National Library of Energy BETA

Sample records for machine controls food

  1. Diamond turning machine controller implementation

    SciTech Connect (OSTI)

    Garrard, K.P.; Taylor, L.W.; Knight, B.F.; Fornaro, R.J.

    1988-12-01

    The standard controller for a Pnuemo ASG 2500 Diamond Turning Machine, an Allen Bradley 8200, has been replaced with a custom high-performance design. This controller consists of four major components. Axis position feedback information is provided by a Zygo Axiom 2/20 laser interferometer with 0.1 micro-inch resolution. Hardware interface logic couples the computers digital and analog I/O channels to the diamond turning machine`s analog motor controllers, the laser interferometer, and other machine status and control information. It also provides front panel switches for operator override of the computer controller and implement the emergency stop sequence. The remaining two components, the control computer hardware and software, are discussed in detail below.

  2. Controlling Motion at the Nanoscale: Rise of the Molecular Machines...

    Office of Scientific and Technical Information (OSTI)

    Published Article: Controlling Motion at the Nanoscale: Rise of the Molecular Machines Title: Controlling Motion at the Nanoscale: Rise of the Molecular Machines Authors: ...

  3. Methods and apparatus for controlling rotary machines

    DOE Patents [OSTI]

    Bagepalli, Bharat Sampathkumaran; Jansen, Patrick Lee; Barnes, Gary R.; Fric, Thomas Frank; Lyons, James Patrick Francis; Pierce, Kirk Gee; Holley, William Edwin; Barbu, Corneliu

    2009-09-01

    A control system for a rotary machine is provided. The rotary machine has at least one rotating member and at least one substantially stationary member positioned such that a clearance gap is defined between a portion of the rotating member and a portion of the substantially stationary member. The control system includes at least one clearance gap dimension measurement apparatus and at least one clearance gap adjustment assembly. The adjustment assembly is coupled in electronic data communication with the measurement apparatus. The control system is configured to process a clearance gap dimension signal and modulate the clearance gap dimension.

  4. Control System Design for Automatic Cavity Tuning Machines

    SciTech Connect (OSTI)

    Carcagno, R.; Khabiboulline, T.; Kotelnikov, S.; Makulski, A.; Nehring, R.; Nogiec, J.; Ross, M.; Schappert, W.; /Fermilab; Goessel, A.; Iversen, J.; Klinke, D.; /DESY

    2009-05-01

    A series of four automatic tuning machines for 9-cell TESLA-type cavities are being developed and fabricated in a collaborative effort among DESY, FNAL, and KEK. These machines are intended to support high-throughput cavity fabrication for construction of large SRF-based accelerator projects. Two of these machines will be delivered to cavity vendors for the tuning of XFEL cavities. The control system for these machines must support a high level of automation adequate for industrial use by non-experts operators. This paper describes the control system hardware and software design for these machines.

  5. Interpolator for numerically controlled machine tools

    DOE Patents [OSTI]

    Bowers, Gary L.; Davenport, Clyde M.; Stephens, Albert E.

    1976-01-01

    A digital differential analyzer circuit is provided that depending on the embodiment chosen can carry out linear, parabolic, circular or cubic interpolation. In the embodiment for parabolic interpolations, the circuit provides pulse trains for the X and Y slide motors of a two-axis machine to effect tool motion along a parabolic path. The pulse trains are generated by the circuit in such a way that parabolic tool motion is obtained from information contained in only one block of binary input data. A part contour may be approximated by one or more parabolic arcs. Acceleration and initial velocity values from a data block are set in fixed bit size registers for each axis separately but simultaneously and the values are integrated to obtain the movement along the respective axis as a function of time. Integration is performed by continual addition at a specified rate of an integrand value stored in one register to the remainder temporarily stored in another identical size register. Overflows from the addition process are indicative of the integral. The overflow output pulses from the second integration may be applied to motors which position the respective machine slides according to a parabolic motion in time to produce a parabolic machine tool motion in space. An additional register for each axis is provided in the circuit to allow "floating" of the radix points of the integrand registers and the velocity increment to improve position accuracy and to reduce errors encountered when the acceleration integrand magnitudes are small when compared to the velocity integrands. A divider circuit is provided in the output of the circuit to smooth the output pulse spacing and prevent motor stall, because the overflow pulses produced in the binary addition process are spaced unevenly in time. The divider has the effect of passing only every nth motor drive pulse, with n being specifiable. The circuit inputs (integrands, rates, etc.) are scaled to give exactly n times the desired number of pulses out, in order to compensate for the divider.

  6. Mining Machine Control Signal Processing System

    SciTech Connect (OSTI)

    Fecitt, G.J.

    1984-01-31

    A signal processing system for an underground mining machine having a steerable mineral cutter and a sensor which senses natural radiation emitted from rock strata overlaying the radiation absorbing mineral and which derives a sensor signal representative of the cutting horizon of the cutter, comprises processing means for receiving and processing the sensor signal to derive an operational signal indicative of the cutter horizon of the cutter, calibration means for accepting a fed in calibration signal representative of a known existing condition of the cutting horizon and comparator means for comparing the derived operational signal with the calibration signal to determine an error in the derived operational signal and for instructing the processing means to apply a suitable correction to the derived operational signal.

  7. Control system for an interior permanent magnet synchronous machine

    SciTech Connect (OSTI)

    Bose, B.K.

    1988-10-12

    A high performance, fully operational, four-quadrant control scheme is used in an interior permanent magnet synchronous machine. The machine operates smoothly with full performance in the constant-torque region as well as in the flux-weakening, constant-power region in both directions of motion. The transition between the constant-torque and constant-power regions is very smooth under all conditions of operation. Control in the constant-torque region is based on a vector or field-oriented technique, with the direct-axis aligned with the total stator flux, whereas constant-power region control is accomplished by orientation of the torque angle of the impressed square-wave voltage through the feedforward vector rotator. In a preferred embodiment, the control system employs a digital distributed microcomputer controller arrangement which relies upon various precisely estimated feedback signals, such as torque, flux, etc. The control scheme includes an outer torque control loop primarily for traction type applications, but also contemplates speed and position control loops for various industrial drives. A 70 hp drive system using a Neodymium-Iron-Boron permanent magnet machine and transistor pulse width modulating inverter has been designed and successfully tested. This control scheme also has application in controlling surface permanent magnet machines. 16 figs.

  8. Control coil arrangement for a rotating machine rotor

    DOE Patents [OSTI]

    Shah, Manoj R.; Lewandowsk, Chad R.

    2001-07-31

    A rotating machine (e.g., a turbine, motor or generator) is provided wherein a fixed solenoid or other coil configuration is disposed adjacent to one or both ends of the active portion of the machine rotor for producing an axially directed flux in the active portion so as to provide planar axial control at single or multiple locations for rotor balance, levitation, centering, torque and thrust action. Permanent magnets can be used to produce an axial bias magnetic field. The rotor can include magnetic disks disposed in opposed, facing relation to the coil configuration.

  9. Method and system for controlling a permanent magnet machine

    DOE Patents [OSTI]

    Walters, James E.

    2003-05-20

    Method and system for controlling the start of a permanent magnet machine are provided. The method allows to assign a parameter value indicative of an estimated initial rotor position of the machine. The method further allows to energize the machine with a level of current being sufficiently high to start rotor motion in a desired direction in the event the initial rotor position estimate is sufficiently close to the actual rotor position of the machine. A sensing action allows to sense whether any incremental changes in rotor position occur in response to the energizing action. In the event no changes in rotor position are sensed, the method allows to incrementally adjust the estimated rotor position by a first set of angular values until changes in rotor position are sensed. In the event changes in rotor position are sensed, the method allows to provide a rotor alignment signal as rotor motion continues. The alignment signal allows to align the estimated rotor position relative to the actual rotor position. This alignment action allows for operating the machine over a wide speed range.

  10. Televised remote control system of a continuous mining machine

    SciTech Connect (OSTI)

    Lansberry, J.B.

    1981-08-04

    A method of recovering particulate material from a seam of such material within the earth bounded above and below by different material which comprises the steps of positioning in mining relation to the seam a continuous mining machine having a power driven mechanism thereon for moving the machine through successive seam material cutting cycles which include an advancing movement along a mined entry within the seam in a direction toward the working face of the seam; illuminating portions of the space surrounding the continuous mining machine including portions of the working face disposed forwardly thereof and adjacent portions of the roof, floor and side walls of the mined entry rearwardly of the working face; establishing electromagnetic signals indicative of the appearance of the illuminated portions of the working face of the seam and the adjacent portions of the roof, floor and side walls; transmitting the established electromagnetic signals to a remote control station; converting at the remote control station the transmitted electromagnetic signals to a continuous picture of the appearance of at least a selected portion of the illuminated portions of the working face of the seam and the adjacent portions of the roof, floor and side walls; and controlling from the remote control station the cutting cycle of the continuous mining machine so that the material cut during a cycle is cut from the seam up to the different material defining the roof and down to the different material defining the floor based upon visually distinguishing between the material of the seam and the different material which forms the roof and floor by viewing the continuous picture provided at the remote control station and apparatus for carrying out the method.

  11. Stator for a rotating electrical machine having multiple control windings

    DOE Patents [OSTI]

    Shah, Manoj R.; Lewandowski, Chad R.

    2001-07-17

    A rotating electric machine is provided which includes multiple independent control windings for compensating for rotor imbalances and for levitating/centering the rotor. The multiple independent control windings are placed at different axial locations along the rotor to oppose forces created by imbalances at different axial locations along the rotor. The multiple control windings can also be used to levitate/center the rotor with a relatively small magnetic field per unit area since the rotor and/or the main power winding provides the bias field.

  12. Methods, systems and apparatus for controlling operation of two alternating current (AC) machines

    DOE Patents [OSTI]

    Gallegos-Lopez, Gabriel; Nagashima, James M.; Perisic, Milun; Hiti, Silva

    2012-06-05

    A system is provided for controlling two alternating current (AC) machines via a five-phase PWM inverter module. The system comprises a first control loop, a second control loop, and a current command adjustment module. The current command adjustment module operates in conjunction with the first control loop and the second control loop to continuously adjust current command signals that control the first AC machine and the second AC machine such that they share the input voltage available to them without compromising the target mechanical output power of either machine. This way, even when the phase voltage available to either one of the machines decreases, that machine outputs its target mechanical output power.

  13. Prospects for chaos control of machine tool chatter

    SciTech Connect (OSTI)

    Hively, L.M.; Protopopescu, V.A.; Clapp, N.E.; Daw, C.S.

    1998-06-01

    The authors analyze the nonlinear tool-part dynamics during turning of stainless steel in the nonchatter and chatter regimes, toward the ultimate objective of chatter control. Their previous work analyzed tool acceleration in three dimensions at four spindle speeds. In the present work, the authors analyze the machining power and obtain nonlinear measures of this power. They also calculate the cycle-to-cycle energy for the turning process. Return maps for power cycle times do not reveal fixed points or (un)stable manifolds. Energy return maps do display stable and unstable directions (manifolds) to and from an unstable period-1 orbit, which is the dominant periodicity. Both nonchatter and chatter dynamics have the unusual feature of arriving at the unstable period-1 fixed point and departing from that fixed point of the energy return map in a single step. This unusual feature makes chaos maintenance, based on the well-known Ott-Grebogi-Yorke scheme, a very difficult option for chatter suppression. Alternative control schemes, such as synchronization of the tool-part motion to prerecorded nonchatter dynamics or dynamically damping the period-1 motion, are briefly discussed.

  14. Method and system for controlling a synchronous machine over full operating range

    DOE Patents [OSTI]

    Walters, James E.; Gunawan, Fani S.; Xue, Yanhong

    2002-01-01

    System and method for controlling a synchronous machine are provided. The method allows for calculating a stator voltage index. The method further allows for relating the magnitude of the stator voltage index against a threshold voltage value. An offset signal is generated based on the results of the relating step. A respective state of operation of the machine is determined. The offset signal is processed based on the respective state of the machine.

  15. Direct control of air gap flux in permanent magnet machines

    DOE Patents [OSTI]

    Hsu, John S.

    2000-01-01

    A method and apparatus for field weakening in PM machines uses field weakening coils (35, 44, 45, 71, 72) to produce flux in one or more stators (34, 49, 63, 64), including a flux which counters flux normally produced in air gaps between the stator(s) (34, 49, 63, 64) and the rotor (20, 21, 41, 61) which carries the PM poles. Several modes of operation are introduced depending on the magnitude and polarity of current in the field weakening coils (35, 44, 45, 71, 72). The invention is particularly useful for, but not limited to, the electric vehicle drives and PM generators.

  16. Optimal design of an overall controller of saturated synchronous machine under different loading

    SciTech Connect (OSTI)

    Saleh, A.; El-Gaafary, A.; El-Sherbiny, M.

    1983-06-01

    The main purpose of this paper is to design a feedback system that optimizes the dynamic response of a synchronous machine. Such a system should be stable for any small disturbance. Pontryagin's maximum principle, which gives the solution for the optimal linear regulator problem through the eigenvector method, is applied. The system consists of a synchronous machine connected to an infinite bus through a transmission line. The effect of two control signals fed to the voltage regulator and the mechanical system is investigated. Also the effect of machine saturation on dynamic response is included.

  17. Control system for, and a method of, heating an operator station of a work machine

    DOE Patents [OSTI]

    Baker, Thomas M.; Hoff, Brian D.; Akasam, Sivaprasad

    2005-04-05

    There are situations in which an operator remains in an operator station of a work machine when an engine of the work machine is inactive. The present invention includes a control system for, and a method of, heating the operator station when the engine is inactive. A heating system of the work machine includes an electrically-powered coolant pump, a power source, and at least one piece of warmed machinery. An operator heat controller is moveable between a first and a second position, and is operable to connect the electrically-powered coolant pump to the power source when the engine is inactive and the operator heat controller is in the first position. Thus, by deactivating the engine and then moving the operator heat controller to the first position, the operator may supply electrical energy to the electrically-powered coolant pump, which is operably coupled to heat the operator station.

  18. Pointright: a system to redirect mouse and keyboard control among multiple machines

    DOE Patents [OSTI]

    Johanson, Bradley E.; Winograd, Terry A.; Hutchins, Gregory M.

    2008-09-30

    The present invention provides a software system, PointRight, that allows for smooth and effortless control of pointing and input devices among multiple displays. With PointRight, a single free-floating mouse and keyboard can be used to control multiple screens. When the cursor reaches the edge of a screen it seamlessly moves to the adjacent screen and keyboard control is simultaneously redirected to the appropriate machine. Laptops may also redirect their keyboard and pointing device, and multiple pointers are supported simultaneously. The system automatically reconfigures itself as displays go on, go off, or change the machine they display.

  19. Advanced human-machine interface for collaborative building control

    DOE Patents [OSTI]

    Zheng, Xianjun S.; Song, Zhen; Chen, Yanzi; Zhang, Shaopeng; Lu, Yan

    2015-08-11

    A system for collaborative energy management and control in a building, including an energy management controller, one or more occupant HMIs that supports two-way communication between building occupants and a facility manager, and between building occupants and the energy management controller, and a facility manager HMI that supports two-way communication between the facility manager and the building occupants, and between the facility manager and the energy management controller, in which the occupant HMI allows building occupants to provide temperature preferences to the facility manager and the energy management controller, and the facility manager HMI allows the facility manager to configure an energy policy for the building as a set of rules and to view occupants' aggregated temperature preferences, and the energy management controller determines an optimum temperature range that resolves conflicting occupant temperature preferences and occupant temperature preferences that conflict with the facility manager's energy policy for the building.

  20. Methods, systems and apparatus for controlling operation of two alternating current (AC) machines

    DOE Patents [OSTI]

    Gallegos-Lopez, Gabriel; Nagashima, James M.; Perisic, Milun; Hiti, Silva

    2012-02-14

    A system is provided for controlling two AC machines. The system comprises a DC input voltage source that provides a DC input voltage, a voltage boost command control module (VBCCM), a five-phase PWM inverter module coupled to the two AC machines, and a boost converter coupled to the inverter module and the DC input voltage source. The boost converter is designed to supply a new DC input voltage to the inverter module having a value that is greater than or equal to a value of the DC input voltage. The VBCCM generates a boost command signal (BCS) based on modulation indexes from the two AC machines. The BCS controls the boost converter such that the boost converter generates the new DC input voltage in response to the BCS. When the two AC machines require additional voltage that exceeds the DC input voltage required to meet a combined target mechanical power required by the two AC machines, the BCS controls the boost converter to drive the new DC input voltage generated by the boost converter to a value greater than the DC input voltage.

  1. Adaptive vibration control using synchronous demodulation with machine tool controller motor commutation

    DOE Patents [OSTI]

    Hopkins, David James

    2008-05-13

    A control system and method for actively reducing vibration in a spindle housing caused by unbalance forces on a rotating spindle, by measuring the force-induced spindle-housing motion, determining control signals based on synchronous demodulation, and provide compensation for the measured displacement to cancel or otherwise reduce or attenuate the vibration. In particular, the synchronous demodulation technique is performed to recover a measured spindle housing displacement signal related only to the rotation of a machine tool spindle, and consequently rejects measured displacement not related to spindle motion or synchronous to a cycle of revolution. Furthermore, the controller actuates at least one voice-coil (VC) motor, to cancel the original force-induced motion, and adapts the magnitude of voice coil signal until this measured displacement signal is brought to a null. In order to adjust the signal to a null, it must have the correct phase relative to the spindle angle. The feedback phase signal is used to adjust a common (to both outputs) commutation offset register (offset relative to spindle encoder angle) to force the feedback phase signal output to a null. Once both of these feedback signals are null, the system is compensating properly for the spindle-induced motion.

  2. Study and Development of Anti-Islanding Control for Synchronous Machine-Based Distributed Generators: November 2001--March 2004

    SciTech Connect (OSTI)

    Ye, Z.

    2006-03-01

    This report summarizes the study and development of new active anti-islanding control schemes for synchronous machine-based distributed generators, including engine generators and gas turbines.

  3. Method and system for controlling start of a permanent magnet machine

    DOE Patents [OSTI]

    Walters, James E.; Krefta, Ronald John

    2003-10-28

    Method and system for controlling a permanent magnet machine are provided. The method provides a sensor assembly for sensing rotor sector position relative to a plurality of angular sectors. The method further provides a sensor for sensing angular increments in rotor position. The method allows starting the machine in a brushless direct current mode of operation using a calculated initial rotor position based on an initial angular sector position information from the sensor assembly. Upon determining a transition from the initial angular sector to the next angular sector, the method allows switching to a sinusoidal mode of operation using rotor position based on rotor position information from the incremental sensor.

  4. Method and system for controlling a permanent magnet machine during fault conditions

    DOE Patents [OSTI]

    Krefta, Ronald John; Walters, James E.; Gunawan, Fani S.

    2004-05-25

    Method and system for controlling a permanent magnet machine driven by an inverter is provided. The method allows for monitoring a signal indicative of a fault condition. The method further allows for generating during the fault condition a respective signal configured to maintain a field weakening current even though electrical power from an energy source is absent during said fault condition. The level of the maintained field-weakening current enables the machine to operate in a safe mode so that the inverter is protected from excess voltage.

  5. Methods, systems and apparatus for controlling third harmonic voltage when operating a multi-space machine in an overmodulation region

    SciTech Connect (OSTI)

    Perisic, Milun; Kinoshita, Michael H; Ranson, Ray M; Gallegos-Lopez, Gabriel

    2014-06-03

    Methods, system and apparatus are provided for controlling third harmonic voltages when operating a multi-phase machine in an overmodulation region. The multi-phase machine can be, for example, a five-phase machine in a vector controlled motor drive system that includes a five-phase PWM controlled inverter module that drives the five-phase machine. Techniques for overmodulating a reference voltage vector are provided. For example, when the reference voltage vector is determined to be within the overmodulation region, an angle of the reference voltage vector can be modified to generate a reference voltage overmodulation control angle, and a magnitude of the reference voltage vector can be modified, based on the reference voltage overmodulation control angle, to generate a modified magnitude of the reference voltage vector. By modifying the reference voltage vector, voltage command signals that control a five-phase inverter module can be optimized to increase output voltages generated by the five-phase inverter module.

  6. Method for providing slip energy control in permanent magnet electrical machines

    DOE Patents [OSTI]

    Hsu, John S.

    2006-11-14

    An electric machine (40) has a stator (43), a permanent magnet rotor (38) with permanent magnets (39) and a magnetic coupling uncluttered rotor (46) for inducing a slip energy current in secondary coils (47). A dc flux can be produced in the uncluttered rotor when the secondary coils are fed with dc currents. The magnetic coupling uncluttered rotor (46) has magnetic brushes (A, B, C, D) which couple flux in through the rotor (46) to the secondary coils (47c, 47d) without inducing a current in the rotor (46) and without coupling a stator rotational energy component to the secondary coils (47c, 47d). The machine can be operated as a motor or a generator in multi-phase or single-phase embodiments and is applicable to the hybrid electric vehicle. A method of providing a slip energy controller is also disclosed.

  7. Process automation using combinations of process and machine control technologies with application to a continuous dissolver

    SciTech Connect (OSTI)

    Spencer, B.B.: Yarbro, O.O.

    1991-01-01

    Operation of a continuous rotary dissolver, designed to leach uranium-plutonium fuel from chopped sections of reactor fuel cladding using nitric acid, has been automated. The dissolver is a partly continuous, partly batch process that interfaces at both ends with batchwise processes, thereby requiring synchronization of certain operations. Liquid acid is fed and flows through the dissolver continuously, whereas chopped fuel elements are fed to the dissolver in small batches and move through the compartments of the dissolver stagewise. Sequential logic (or machine control) techniques are used to control discrete activities such as the sequencing of isolation valves. Feedback control is used to control acid flowrates and temperatures. Expert systems technology is used for on-line material balances and diagnostics of process operation. 1 ref., 3 figs.

  8. Gauging apparatus and method, particularly for controlling mining by a mining machine

    SciTech Connect (OSTI)

    Campbell, J.A.; Moynihan, D.J.

    1980-04-29

    Apparatus for and method are claimed for controlling the mining by a mining machine of a seam of material (e.g., coal) overlying or underlying a stratum of undesired material (e.g., clay) to reduce the quantity of undesired material mined with the desired material, the machine comprising a cutter movable up and down and adapted to cut down into a seam of coal on being lowered. The control apparatus comprises a first electrical signal constituting a slow-down signal adapted to be automatically operated to signal when the cutter has cut down into a seam of desired material generally to a predetermined depth short of the interface between the seam and the underlying stratum for slowing down the cutting rate as the cutter approaches the interface, and a second electrical signal adapted to be automatically operated subsequent to the first signal for signalling when the cutter has cut down through the seam to the interface for stopping the cutting operation, thereby to avoid mining undesired material with the desired material. Similar signalling may be provided on an upward cut to avoid cutting into the overlying stratum.

  9. An optimal control to improve transient stability of multi-machine power system

    SciTech Connect (OSTI)

    Yamashita, K.; Okano, K.; Tanoguchi, T.

    1982-03-01

    The authors proposed previously an optimal control method to stabilize the power system under large disturbance. This method is based on Lyapunov function and only those feedback signals are used which are given by the time differentiated state variables. In this paper, the discussion is extended from the earlier paper using the extended Lyapunov function and feedback signals which are represented by state variables. Mathematically speaking, the results of the earlier paper are extended by performing some additional matrix operations. The feedback signal is given by a linear combination of state variables (e.g., phase differences between machines) and time differentiated state variables (e.g., generator speed). The time derivative of the extended Lyapunov function is expressed as a quadratic form of feedback gains and the optimal gains are derived by the quadratic form minimization technique. All the nonlinearities of the analyzed system are always retained. Effectiveness of the proposed control scheme is demonstrated by digital computer simulation of three-machine system subject to a large disturbance.

  10. Electro-mechanical energy conversion system having a permanent magnet machine with stator, resonant transfer link and energy converter controls

    DOE Patents [OSTI]

    Skeist, S. Merrill; Baker, Richard H.

    2006-01-10

    An electro-mechanical energy conversion system coupled between an energy source and an energy load comprising an energy converter device including a permanent magnet induction machine coupled between the energy source and the energy load to convert the energy from the energy source and to transfer the converted energy to the energy load and an energy transfer multiplexer to control the flow of power or energy through the permanent magnetic induction machine.

  11. Technology Roadmap Instrumentation, Control, and Human-Machine Interface to Support DOE Advanced Nuclear Energy Programs

    SciTech Connect (OSTI)

    Donald D Dudenhoeffer; Burce P Hallbert

    2007-03-01

    Instrumentation, Controls, and Human-Machine Interface (ICHMI) technologies are essential to ensuring delivery and effective operation of optimized advanced Generation IV (Gen IV) nuclear energy systems. In 1996, the Watts Bar I nuclear power plant in Tennessee was the last U.S. nuclear power plant to go on line. It was, in fact, built based on pre-1990 technology. Since this last U.S. nuclear power plant was designed, there have been major advances in the field of ICHMI systems. Computer technology employed in other industries has advanced dramatically, and computing systems are now replaced every few years as they become functionally obsolete. Functional obsolescence occurs when newer, more functional technology replaces or supersedes an existing technology, even though an existing technology may well be in working order.Although ICHMI architectures are comprised of much of the same technology, they have not been updated nearly as often in the nuclear power industry. For example, some newer Personal Digital Assistants (PDAs) or handheld computers may, in fact, have more functionality than the 1996 computer control system at the Watts Bar I plant. This illustrates the need to transition and upgrade current nuclear power plant ICHMI technologies.

  12. Instrumentation, Controls, and Human-Machine Interface Technology Development Roadmap in Support of Grid Appropriate Reactors

    SciTech Connect (OSTI)

    Holcomb, David Eugene [ORNL] [ORNL; Upadhyaya, Belle R. [University of Tennessee, Knoxville (UTK)] [University of Tennessee, Knoxville (UTK); Kisner, Roger A [ORNL] [ORNL; O'Hara, John [Brookhaven National Laboratory (BNL)] [Brookhaven National Laboratory (BNL); Quinn, Edward L. [Longenecker & Associates] [Longenecker & Associates; Miller, Don W. [Ohio State University] [Ohio State University

    2009-01-01

    Grid Appropriate Reactors (GARs) are a component of the U.S. Department of Energy s (DOE s) Global Nuclear Energy Partnership (GNEP) program. GARs have smaller output power (<~600 MWe), than those intended for deployment on large, tightly coupled grids. This smaller size is important in avoiding grid destabilization, which can result from having a large fraction of a grid s electrical generation supplied by a single source. GARs are envisioned to be deployed worldwide often in locations without extensive nuclear power experience. DOE recently sponsored the creation of an Instrumentation, Controls, and Human-Machine Interface (ICHMI) technology development roadmap emphasizing the specific characteristics of GARs [1]. This roadmapping effort builds upon and focuses the recently developed, more general nuclear energy ICHMI technology development roadmap [2]. The combination of the smaller plant size, smaller grids, and deployment in locations without extensive prior nuclear power experience presents particular infrastructure, regulation, design, operational, and safeguards challenges for effective GAR deployment. ICHMI technologies are central to efficient GAR operation and as such are a dimension of each of these challenges. Further, while the particular ICHMI technologies to be developed would be useful at larger power plants, they are not high-priority development items at the larger plants. For example, grid transient resilience would be a useful feature for any reactor/grid combination and indeed would have limited some recent blackout events. However, most large reactors have limited passive cooling features. Large plants with active safety response features will likely preserve trip preferential grid transient response. This contrasts sharply with GARs featuring passive shutdown cooling, which can safely support grid stability during large grid transients. ICHMI technologies ranging from alternative control algorithms to simplified human-interface system designs are key to enabling GARs to respond properly and thereby stabilize the grid during transients.

  13. A new pole-placement method for excitation control design to damp SSR of a nonidentical two-machine system

    SciTech Connect (OSTI)

    Li, Q.H.; Zhao, D.Z.; Yu, Y.N.

    1989-08-01

    A new pole-placement method is developed in this paper for excitation control design to control a multimode SSR of the Second Benchmark Model, System 2. The system has two non-identical turbine-generators closely coupled. The method uses signals selected from participation factor analysis for the local feedback. Both eigenvalue analysis and nonlinear simulation test show that the control thus designed is very effective to control the multimode torsional oscillations of the system. Torsional interaction of the two closely coupled machines is also analyzed.

  14. Real time control of micro-machine system using micro-computer based fuzzy logic power system stabilizer

    SciTech Connect (OSTI)

    Hiyama, Takashi . Dept. of Electrical Engineering and Computer Science)

    1994-12-01

    A micro-computer based fuzzy logic power system stabilizer is applied to a micro-machine system to investigate its efficiency in real time control. The stabilizing signal is determined by using measured speed or real power signals at every sampling time to damp the system oscillations. The results show the proposed stabilizer improves the system damping effectively subject to various types of disturbances.

  15. Induction machine

    DOE Patents [OSTI]

    Owen, Whitney H.

    1980-01-01

    A polyphase rotary induction machine for use as a motor or generator utilizing a single rotor assembly having two series connected sets of rotor windings, a first stator winding disposed around the first rotor winding and means for controlling the current induced in one set of the rotor windings compared to the current induced in the other set of the rotor windings. The rotor windings may be wound rotor windings or squirrel cage windings.

  16. z machine

    National Nuclear Security Administration (NNSA)

    Z%20Machine%201808.jpg" alt"Air-gas breakdown when Z Machine at Sandia National Laboratories fires." title"Air-gas breakdown when Z Machine at Sandia National...

  17. FINAL REPORT ON CONTROL ALGORITHM TO IMPROVE THE PARTIAL-LOAD EFFICIENCY OFSURFACE PM MACHINES WITH FRACTIONAL-SLOT CONCENTRATED WINDINGS

    SciTech Connect (OSTI)

    Reddy, P.B.; Jahns, T.M.

    2007-04-30

    Surface permanent magnet (SPM) synchronous machines using fractional-slot concentrated windings are being investigated as candidates for high-performance traction machines for automotive electric propulsion systems. It has been shown analytically and experimentally that such designs can achieve very wide constant-power speed ratios (CPSR) [1,2]. This work has shown that machines of this type are capable of achieving very low cogging torque amplitudes as well as significantly increasing the machine power density [3-5] compared to SPM machines using conventional distributed windings. High efficiency can be achieved in this class of SPM machine by making special efforts to suppress the eddy-current losses in the magnets [6-8], accompanied by efforts to minimize the iron losses in the rotor and stator cores. Considerable attention has traditionally been devoted to maximizing the full-load efficiency of traction machines at their rated operating points and along their maximum-power vs. speed envelopes for higher speeds [9,10]. For example, on-line control approaches have been presented for maximizing the full-load efficiency of PM synchronous machines, including the use of negative d-axis stator current to reduce the core losses [11,12]. However, another important performance specification for electric traction applications is the machine's efficiency at partial loads. Partial-load efficiency is particularly important if the target traction application requires long periods of cruising operation at light loads that are significantly lower than the maximum drive capabilities. While the design of the machine itself is clearly important, investigation has shown that this is a case where the choice of the control algorithm plays a critical role in determining the maximum partial-load efficiency that the machine actually achieves in the traction drive system. There is no evidence that this important topic has been addressed for this type of SPM machine by any other authors. This topic takes on even greater significance for fractional-slot concentrated-winding SPM machine designs. In particular, maximizing the torque/power density of this class of SPM machines typically leads to machine designs with high numbers of poles. The resulting high electrical frequencies can easily result in high stator core losses unless special care is taken during the machine design process. The purpose of this report is to discuss a modified vector control algorithm for a fractional-slot concentrated winding SPM machine that has been developed to maximize the machine's partial-load efficiency over a wide range of operating conditions. For purposes of this discussion, a 55 kW (peak) SPM machine designed to meet requirements established in the US FreedomCar program [13] is used as the basis for demonstrating the proposed technique. A combination of closed-form analysis [14] and finite element analysis (FEA) is used during this investigation.

  18. Final Report on Control Algorithm to Improve the Partial-Load Efficiency of Surface PM Machines with Fractional-Slot Concentrated Windings

    SciTech Connect (OSTI)

    McKeever, John W; Reddy, Patel; Jahns, Thomas M

    2007-05-01

    Surface permanent magnet (SPM) synchronous machines using fractional-slot concentrated windings are being investigated as candidates for high-performance traction machines for automotive electric propulsion systems. It has been shown analytically and experimentally that such designs can achieve very wide constant-power speed ratios (CPSR) [1,2]. This work has shown that machines of this type are capable of achieving very low cogging torque amplitudes as well as significantly increasing the machine power density [3-5] compared to SPM machines using conventional distributed windings. High efficiency can be achieved in this class of SPM machine by making special efforts to suppress the eddy-current losses in the magnets [6-8], accompanied by efforts to minimize the iron losses in the rotor and stator cores. Considerable attention has traditionally been devoted to maximizing the full-load efficiency of traction machines at their rated operating points and along their maximum-power vs. speed envelopes for higher speeds [9,10]. For example, on-line control approaches have been presented for maximizing the full-load efficiency of PM synchronous machines, including the use of negative d-axis stator current to reduce the core losses [11,12]. However, another important performance specification for electric traction applications is the machine's efficiency at partial loads. Partial-load efficiency is particularly important if the target traction application requires long periods of cruising operation at light loads that are significantly lower than the maximum drive capabilities. While the design of the machine itself is clearly important, investigation has shown that this is a case where the choice of the control algorithm plays a critical role in determining the maximum partial-load efficiency that the machine actually achieves in the traction drive system. There is no evidence that this important topic has been addressed for this type of SPM machine by any other authors. This topic takes on even greater significance for fractional-slot concentrated-winding SPM machine designs. In particular, maximizing the torque/power density of this class of SPM machines typically leads to machine designs with high numbers of poles. The resulting high electrical frequencies can easily result in high stator core losses unless special care is taken during the machine design process. The purpose of this report is to discuss a modified vector control algorithm for a fractional-slot concentrated winding SPM machine that has been developed to maximize the machine's partial-load efficiency over a wide range of operating conditions. For purposes of this discussion, a 55 kW (peak) SPM machine designed to meet requirements established in the US FreedomCar program [13] is used as the basis for demonstrating the proposed technique. A combination of closed-form analysis [14] and finite element analysis (FEA) is used during this investigation.

  19. Develop a field grid system for yield mapping and machine control. Quarterly report, July 1, 1995--September 30, 1995

    SciTech Connect (OSTI)

    Hart, F.; Windish, J.

    1995-10-01

    Build and test the Field Grid Sense system for yield mapping and machine control during harvesting. Secondly, use Field Grid Sense with chemical application equipment to demonstrate a workable in-field system. More specifically, the operation of the patented hardware/software Field Grid Sense (FGS) system will be tested in crop harvesting to demonstrate the system`s utility and to analyze the flexibility of operation under true field conditions. Additionally, FGS will again be used with chemical application equipment - equipment that needs modification to correct one or two slight shortcomings. This action will create improved systems and establish the worthiness, efficiency and necessity of chemical application equipment that is controlled and directed via the FGS package.

  20. A Prototyping Environment for Research on Human-Machine Interfaces in Process Control: Use of Microsoft WPF for Microworld and Distributed Control System Development

    SciTech Connect (OSTI)

    Roger Lew; Ronald L. Boring; Thomas A. Ulrich

    2014-08-01

    Operators of critical processes, such as nuclear power production, must contend with highly complex systems, procedures, and regulations. Developing human-machine interfaces (HMIs) that better support operators is a high priority for ensuring the safe and reliable operation of critical processes. Human factors engineering (HFE) provides a rich and mature set of tools for evaluating the performance of HMIs, but the set of tools for developing and designing HMIs is still in its infancy. Here we propose that Microsoft Windows Presentation Foundation (WPF) is well suited for many roles in the research and development of HMIs for process control.

  1. New approach for the solution of optimal control problems on parallel machines. Doctoral thesis

    SciTech Connect (OSTI)

    Stech, D.J.

    1990-01-01

    This thesis develops a highly parallel solution method for nonlinear optimal control problems. Balakrishnan's epsilon method is used in conjunction with the Rayleigh-Ritz method to convert the dynamic optimization of the optimal control problem into a static optimization problem. Walsh functions and orthogonal polynomials are used as basis functions to implement the Rayleigh-Ritz method. The resulting static optimization problem is solved using matrix operations which have well defined massively parallel solution methods. To demonstrate the method, a variety of nonlinear optimal control problems are solved. The nonlinear Raleigh problem with quadratic cost and nonlinear van der Pol problem with quadratic cost and terminal constraints on the states are solved in both serial and parallel on an eight processor Intel Hypercube. The solutions using both Walsh functions and Legendre polynomials as basis functions are given. In addition to these problems which are solved in parallel, a more complex nonlinear minimum time optimal control problem and nonlinear optimal control problem with an inequality constraint on the control are solved. Results show the method converges quickly, even from relatively poor initial guesses for the nominal trajectories.

  2. Control method and system for hydraulic machines employing a dynamic joint motion model

    DOE Patents [OSTI]

    Danko, George

    2011-11-22

    A control method and system for controlling a hydraulically actuated mechanical arm to perform a task, the mechanical arm optionally being a hydraulically actuated excavator arm. The method can include determining a dynamic model of the motion of the hydraulic arm for each hydraulic arm link by relating the input signal vector for each respective link to the output signal vector for the same link. Also the method can include determining an error signal for each link as the weighted sum of the differences between a measured position and a reference position and between the time derivatives of the measured position and the time derivatives of the reference position for each respective link. The weights used in the determination of the error signal can be determined from the constant coefficients of the dynamic model. The error signal can be applied in a closed negative feedback control loop to diminish or eliminate the error signal for each respective link.

  3. TAS::89 0927::TAS RECOVERY - The Lean Green Energy Controller Machine

    SciTech Connect (OSTI)

    Teeter, John; Wang, Gene; Moss, David

    2012-12-30

    Achieving efficiency improvements and providing demand-response programs have been identified as key elements of our national energy initiative. The residential market is the largest, yet most difficult, segment to engage in efforts to meet these objectives. This project developed Energy Management System that engages the consumer and enables Smart Grid services, applications, and business processes to address this need. Our innovative solution provides smart controller providing dynamic optimization of energy consumption for the residential energy consumer. Our solution extends the technical platform to include a cloud based Internet of Things (IoT) aggregation of data sensors and actuators the go beyond energy management and extend to life style services provided through compelling mobile and console based user experiences.

  4. Controlled-force end seal arrangement for an air press of a papermaking machine

    DOE Patents [OSTI]

    Beck, David A.

    2003-07-08

    An air press for pressing a fiber web includes a plurality of rolls and a pair of end seal arrangements. Of the plurality of rolls, each pair of adjacent rolls forms a nip therebetween. Further, each roll has a pair of roll ends, the plurality of rolls together forming two sets of roll ends. Each end seal arrangement coacts with one set of roll ends, the plurality of rolls and the pair of end seal arrangements together defining an air press chamber having an air chamber pressure. Each end seal arrangement is composed of at least one roll seal, including a first roll seal, and an adjustable bias mechanism. Each roll seal forms a seal with at least one roll end, and one side of the first roll seal being exposed to the air chamber pressure. The adjustable bias mechanism is configured for controlling a position of each roll seal relative to a respective at least one roll end and for adjusting a seal force between the roll seal and the respective at least one roll end.

  5. Electric machine

    DOE Patents [OSTI]

    El-Refaie, Ayman Mohamed Fawzi; Reddy, Patel Bhageerath

    2012-07-17

    An interior permanent magnet electric machine is disclosed. The interior permanent magnet electric machine comprises a rotor comprising a plurality of radially placed magnets each having a proximal end and a distal end, wherein each magnet comprises a plurality of magnetic segments and at least one magnetic segment towards the distal end comprises a high resistivity magnetic material.

  6. Doubly fed induction machine

    DOE Patents [OSTI]

    Skeist, S. Merrill; Baker, Richard H.

    2005-10-11

    An electro-mechanical energy conversion system coupled between an energy source and an energy load including an energy converter device having a doubly fed induction machine coupled between the energy source and the energy load to convert the energy from the energy source and to transfer the converted energy to the energy load and an energy transfer multiplexer coupled to the energy converter device to control the flow of power or energy through the doubly fed induction machine.

  7. Reactor refueling machine simulator

    SciTech Connect (OSTI)

    Rohosky, T.L.; Swidwa, K.J.

    1987-10-13

    This patent describes in combination: a nuclear reactor; a refueling machine having a bridge, trolley and hoist each driven by a separate motor having feedback means for generating a feedback signal indicative of movement thereof. The motors are operable to position the refueling machine over the nuclear reactor for refueling the same. The refueling machine also has a removable control console including means for selectively generating separate motor signals for operating the bridge, trolley and hoist motors and for processing the feedback signals to generate an indication of the positions thereof, separate output leads connecting each of the motor signals to the respective refueling machine motor, and separate input leads for connecting each of the feedback means to the console; and a portable simulator unit comprising: a single simulator motor; a single simulator feedback signal generator connected to the simulator motor for generating a simulator feedback signal in response to operation of the simulator motor; means for selectively connecting the output leads of the console to the simulator unit in place of the refueling machine motors, and for connecting the console input leads to the simulator unit in place of the refueling machine motor feedback means; and means for driving the single simulator motor in response to any of the bridge, trolley or hoist motor signals generated by the console and means for applying the simulator feedback signal to the console input lead associated with the motor signal being generated by the control console.

  8. Earth boring machine and method

    SciTech Connect (OSTI)

    Sullinger, R.

    1983-09-13

    An earth boring machine and method are disclosed. An above-ground reference line, such as a laser beam, is established for a hole to be bored. The direction of the reference line is detected. The direction of a cutting head of the boring machine in a bore hole is detected and signals of the detected direction are transmitted to a control unit for comparison with the reference line direction. The boring machine is controlled with, for example, cam actuated adjustable peripheral cutters on the cutting head so that the direction of the boring machine can be adjusted to that of the reference line.

  9. Integrated Inverter For Driving Multiple Electric Machines

    DOE Patents [OSTI]

    Su, Gui-Jia [Knoxville, TN; Hsu, John S [Oak Ridge, TN

    2006-04-04

    An electric machine drive (50) has a plurality of inverters (50a, 50b) for controlling respective electric machines (57, 62), which may include a three-phase main traction machine (57) and two-phase accessory machines (62) in a hybrid or electric vehicle. The drive (50) has a common control section (53, 54) for controlling the plurality of inverters (50a, 50b) with only one microelectronic processor (54) for controlling the plurality of inverters (50a, 50b), only one gate driver circuit (53) for controlling conduction of semiconductor switches (S1-S10) in the plurality of inverters (50a, 50b), and also includes a common dc bus (70), a common dc bus filtering capacitor (C1) and a common dc bus voltage sensor (67). The electric machines (57, 62) may be synchronous machines, induction machines, or PM machines and may be operated in a motoring mode or a generating mode.

  10. A microcomputer-based control and simulation of an advanced IPM (interior permanent magnet) synchronous machine drive system for electric vehicle propulsion

    SciTech Connect (OSTI)

    Bose, B.K.; Szczesny, P.M.

    1987-01-01

    Advanced digital control and computer-aided control system design techniques are playing key roles in the complex drive system design and control implementation. The paper describes a high performance microcomputer-based control and digital simulation of an inverter-fed interior permanent magnet (IPM) synchronous machine which uses Neodymium-Iron-Boron magnet. The fully operational four-quadrant drive system includes constant-torque region with zero speed operation and high speed field-weakening constant-power region. The control uses vector or field-oriented technique in constant-torque region with the direct axis aligned to the stator flux, whereas the constant-power region control is based on torque angle orientation of the impressed square-wave voltage. All the key feedback signals for the control are estimated with precision. The drive system is basically designed with an outer torque control loop for electric vehicle appliation, but speed and position control loops can be added for other industrial applications. The distributed microcomputer-based control system is based on Intel-8096 microcontroller and Texas Instruments TMS32010 type digital signal processor. The complete drive system has been simulated using the VAX-based simulation language SIMMON to verify the feasibility of the control laws and to study the performances of the drive system. The simulation results are found to have excellent correlation with the laboratory breadboard tests. 19 refs., 14 figs., 5 tabs.

  11. U.S. Department Of Energy Advanced Small Modular Reactor R&D Program: Instrumentation, Controls, and Human-Machine Interface (ICHMI) Pathway

    SciTech Connect (OSTI)

    Holcomb, David Eugene; Wood, Richard Thomas

    2013-01-01

    Instrumentation, controls, and human-machine interfaces (ICHMI) are essential enabling technologies that strongly influence nuclear power plant performance and operational costs. The nuclear power industry is currently engaged in a transition from traditional analog-based instrumentation, controls, and human-machine interface systems to implementations employing digital technologies. This transition has primarily occurred in an ad hoc fashion through individual system upgrades at existing plants and has been constrained by licenseability concerns. Although the recent progress in constructing new plants has spurred design of more fully digital plant-wide ICHMI systems, the experience base in the nuclear power application domain is limited. Additionally, development of advanced reactor concepts, such as Generation IV designs and small modular reactors, introduces different plant conditions (e.g., higher temperatures, different coolants, etc.) and unique plant configurations (e.g., multiunit plants with shared systems, balance of plant architectures with reconfigurable co-generation options) that increase the need for enhanced ICHMI capabilities to fully achieve industry goals related to economic competitiveness, safety and reliability, sustainability, and proliferation resistance and physical protection. As a result, significant challenges remain to be addressed to enable the nuclear power industry to complete the transition to safe and comprehensive use of modern ICHMI technology. The U.S. Department of Energy (DOE) has recognized that ICHMI research, development, and demonstration (RD&D) is needed to resolve the technical challenges that may compromise the effective and efficient utilization of modern ICHMI technology and consequently inhibit realization of the benefits offered by expanded utilization of nuclear power. Consequently, several DOE programs have substantial ICHMI RD&D elements within their respective research portfolios. This paper describes current ICHMI research in support of advanced small modular reactors. The objectives that can be achieved through execution of the defined RD&D are to provide optimal technical solutions to critical ICHMI issues, resolve technology gaps arising from the unique measurement and control characteristics of advanced reactor concepts, provide demonstration of needed technologies and methodologies in the nuclear power application domain, mature emerging technologies to facilitate commercialization, and establish necessary technical evidence and application experience to enable timely and predictable licensing. 1 Introduction Instrumentation, controls, and human-machine interfaces are essential enabling technologies that strongly influence nuclear power plant performance and operational costs. The nuclear power industry is currently engaged in a transition from traditional analog-based instrumentation, controls, and human-machine interface (ICHMI) systems to implementations employing digital technologies. This transition has primarily occurred in an ad hoc fashion through individual system upgrades at existing plants and has been constrained by licenseability concerns. Although the recent progress in constructing new plants has spurred design of more fully digital plant-wide ICHMI systems, the experience base in the nuclear power application domain is limited. Additionally, development of advanced reactor concepts, such as Generation IV designs and small modular reactors, introduces different plant conditions (e.g., higher temperatures, different coolants, etc.) and unique plant configurations (e.g., multiunit plants with shared systems, balance of plant architectures with reconfigurable co-generation options) that increase the need for enhanced ICHMI capabilities to fully achieve industry goals related to economic competitiveness, safety and reliability, sustainability, and proliferation resistance and physical protection. As a result, significant challenges remain to be addressed to enable the nuclear power industry to complete the transition to safe and comprehensive use of m

  12. Diagnostics and Control of Natural Gas-Fired furnaces via Flame Image Analysis using Machine Vision & Artificial Intelligence Techniques

    SciTech Connect (OSTI)

    Shahla Keyvan

    2005-12-01

    A new approach for the detection of real-time properties of flames is used in this project to develop improved diagnostics and controls for natural gas fired furnaces. The system utilizes video images along with advanced image analysis and artificial intelligence techniques to provide virtual sensors in a stand-alone expert shell environment. One of the sensors is a flame sensor encompassing a flame detector and a flame analyzer to provide combustion status. The flame detector can identify any burner that has not fired in a multi-burner furnace. Another sensor is a 3-D temperature profiler. One important aspect of combustion control is product quality. The 3-D temperature profiler of this on-line system is intended to provide a tool for a better temperature control in a furnace to improve product quality. In summary, this on-line diagnostic and control system offers great potential for improving furnace thermal efficiency, lowering NOx and carbon monoxide emissions, and improving product quality. The system is applicable in natural gas-fired furnaces in the glass industry and reheating furnaces used in steel and forging industries.

  13. Celestial Mystery Machine

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Celestial Mystery Machine 1663 Los Alamos science and technology magazine Latest Issue:October 2015 past issues All Issues submit Celestial Mystery Machine High-energy gamma...

  14. Climate Time-Machine

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Climate Time-Machine Climate Time-Machine 20th Century Reanalysis Project Explores Earth's Past and Future Climate January 25, 2011 Berkeley Lab Contact: Jon Bashor, ...

  15. Identification of synchronous machine parameters

    SciTech Connect (OSTI)

    Shaban, A.O.

    1985-01-01

    The synchronous machine is an essential component of a power system and determination of its parameters accurately is an important task in securing adequate modes of operation through certain control strategies. An estimation technique based on the Powell algorithm was evaluated for the identification of these parameters on the basis of small-signal input-output data. A fifth order Park domain flux linkage model of a salient pole machine was used for the identification of the parameters. Stator terminal voltages as transformed into the Park domain, field voltage and rotor frequency were used as input signals to the model. The input signals to the actual machine are the stator terminal voltages and the field voltage. The Park domain stator terminal current and field current were used as output signals. Due to the lack of access to real data, digital simulation of an actual machine as used in an effort to establish the machine responses in the time domain to small changes in the input signals. These responses were compared with those obtained from the model with the unknown parameters and utilized in the identification process. The sensitivity of a least-square loss-function with respect to each parameter was tested. The proposed parameter identification method was evaluated with data of two different machines. Careful observation of the results indicates that convergence can only be secured if nonsimultaneous perturbation of the direct - and quadrature - axis components of the terminal voltages is applied.

  16. Initial Experimental Results of a Machine Learning-Based Temperature...

    Office of Scientific and Technical Information (OSTI)

    Temperature Control System for an RF Gun Citation Details In-Document Search Title: Initial Experimental Results of a Machine Learning-Based Temperature Control ...

  17. Novel Flux Coupling Machine without Permanent Magnets - U Machine...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Magnets - U Machine Novel Flux Coupling Machine without Permanent Magnets - U Machine 2009 DOE Hydrogen Program and Vehicle Technologies Program Annual Merit Review and Peer ...

  18. Designing a parallel simula machine

    SciTech Connect (OSTI)

    Papazoglou, M.P.; Georgiadis, P.I.; Maritsas, D.G.

    1983-10-01

    The parallel simula machine (PSM) architecture is based upon a master/slave topology, incorporating a master microprocessor. Interconnection circuitry between the master and slave processor modules uses a timesharing system bus and various programmable interrupt control units. Common and private memory modules reside in the PSM, and direct memory access transfers ease the master processor's workload. 5 references.

  19. Physics Informed Machine Learning

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Physics Informed Machine Learning Physics Informed Machine Learning WHEN: Jan 19, 2016 8:00 AM - Jan 22, 2016 4:00 PM WHERE: Inn at Loretto, Santa Fe CATEGORY: Science TYPE: ...

  20. Stirling machine operating experience

    SciTech Connect (OSTI)

    Ross, B.; Dudenhoefer, J.E.

    1991-01-01

    Numerous Stirling machines have been built and operated, but the operating experience of these machines is not well known. It is important to examine this operating experience in detail, because it largely substantiates the claim that Stirling machines are capable of reliable and lengthy lives. The amount of data that exists is impressive, considering that many of the machines that have been built are developmental machines intended to show proof of concept, and were not expected to operate for any lengthy period of time. Some Stirling machines (typically free-piston machines) achieve long life through non-contact bearings, while other Stirling machines (typically kinematic) have achieved long operating lives through regular seal and bearing replacements. In addition to engine and system testing, life testing of critical components is also considered.

  1. Physics Informed Machine Learning

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Physics Informed Machine Learning Physics Informed Machine Learning WHEN: Jan 19, 2016 8:00 AM - Jan 22, 2016 4:00 PM WHERE: Inn at Loretto, Santa Fe CATEGORY: Science TYPE:...

  2. Estimated general population control limits for unitary agents in drinking water, milk, soil, and unprocessed food items

    SciTech Connect (OSTI)

    Watson, A.P.; Adams, J.D.; Cerar, R.J.; Hess, T.L.; Kistner, S.L.; Leffingwell, S.S.; MacIntosh, R.G.; Ward, J.R.

    1992-01-01

    In the event of an unplanned release of chemical agent during any stage of the Chemical Stockpile Disposal Program (CSDP), the potential exists for contamination of drinking water, forage crops, grains, garden produce, and livestock. Persistent agents such as VX or sulfur mustard pose the greatest human health concern for reentry. This White Paper has been prepared to provide technical bases for these decisions by developing working estimates of agent control limits in selected environmental media considered principal sources of potential human exposure. To date, control limits for public exposure to unitary agents have been established for atmospheric concentrations only. The current analysis builds on previous work to calculate working estimates of control limits for ingestion and dermal exposure to potentially contaminated drinking water, milk, soil, and unprocessed food items such as garden produce. Information characterizing agent desorption from, and detection on or in, contaminated porous media are presently too developed to permit reasonable estimation of dermal exposure from this source. Thus, dermal contact with potentially contaminated porous surfaces is not considered in this document.

  3. Specimen coordinate automated measuring machine/fiducial automated measuring machine

    DOE Patents [OSTI]

    Hedglen, Robert E.; Jacket, Howard S.; Schwartz, Allan I.

    1991-01-01

    The Specimen coordinate Automated Measuring Machine (SCAMM) and the Fiducial Automated Measuring Machine (FAMM) is a computer controlled metrology system capable of measuring length, width, and thickness, and of locating fiducial marks. SCAMM and FAMM have many similarities in their designs, and they can be converted from one to the other without taking them out of the hot cell. Both have means for: supporting a plurality of samples and a standard; controlling the movement of the samples in the +/- X and Y directions; determining the coordinates of the sample; compensating for temperature effects; and verifying the accuracy of the measurements and repeating as necessary. SCAMM and FAMM are designed to be used in hot cells.

  4. HUMAN MACHINE COOPERATIVE TELEROBOTICS

    SciTech Connect (OSTI)

    William R. Hamel; Spivey Douglass; Sewoong Kim; Pamela Murray; Yang Shou; Sriram Sridharan; Ge Zhang; Scott Thayer; Rajiv V. Dubey

    2003-06-30

    The remediation and deactivation and decommissioning (D&D) of nuclear waste storage tanks using telerobotics is one of the most challenging tasks faced in environmental cleanup. Since a number of tanks have reached the end of their design life and some of them have leaks, the unstructured, uncertain and radioactive environment makes the work inefficient and expensive. However, the execution time of teleoperation consumes ten to hundred times that of direct contact with an associated loss in quality. Thus, a considerable effort has been expended to improve the quality and efficiency of telerobotics by incorporating into teleoperation and robotic control functions such as planning, trajectory generation, vision, and 3-D modeling. One example is the Robot Task Space Analyzer (RTSA), which has been developed at the Robotics and Electromechanical Systems Laboratory (REMSL) at the University of Tennessee in support of the D&D robotic work at the Oak Ridge National Laboratory and the National Energy Technology Laboratory. This system builds 3-D models of the area of interest in task space through automatic image processing and/or human interactive manual modeling. The RTSA generates a task plan file, which describes the execution of a task including manipulator and tooling motions. The high level controller of the manipulator interprets the task plan file and executes the task automatically. Thus, if the environment is not highly unstructured, a tooling task, which interacts with environment, will be executed in the autonomous mode. Therefore, the RTSA not only increases the system efficiency, but also improves the system reliability because the operator will act as backstop for safe operation after the 3-D models and task plan files are generated. However, unstructured conditions of environment and tasks necessitate that the telerobot operates in the teleoperation mode for successful execution of task. The inefficiency in the teleoperation mode led to the research described as Human Machine Cooperative Telerobotics (HMCTR). The HMCTR combines the telerobot with robotic control techniques to improve the system efficiency and reliability in teleoperation mode. In this topical report, the control strategy, configuration and experimental results of Human Machines Cooperative Telerobotics (HMCTR), which modifies and limits the commands of human operator to follow the predefined constraints in the teleoperation mode, is described. The current implementation is a laboratory-scale system that will be incorporated into an engineering-scale system at the Oak Ridge National Laboratory in the future.

  5. Machine tool locator

    DOE Patents [OSTI]

    Hanlon, John A.; Gill, Timothy J.

    2001-01-01

    Machine tools can be accurately measured and positioned on manufacturing machines within very small tolerances by use of an autocollimator on a 3-axis mount on a manufacturing machine and positioned so as to focus on a reference tooling ball or a machine tool, a digital camera connected to the viewing end of the autocollimator, and a marker and measure generator for receiving digital images from the camera, then displaying or measuring distances between the projection reticle and the reference reticle on the monitoring screen, and relating the distances to the actual position of the autocollimator relative to the reference tooling ball. The images and measurements are used to set the position of the machine tool and to measure the size and shape of the machine tool tip, and examine cutting edge wear. patent

  6. Initial Experimental Results of a Machine Learning-Based Temperature...

    Office of Scientific and Technical Information (OSTI)

    Initial Experimental Results of a Machine Learning-Based Temperature Control System for an RF Gun Citation Details In-Document Search Title: Initial Experimental Results of a...

  7. Diamond machine tool face lapping machine

    DOE Patents [OSTI]

    Yetter, H.H.

    1985-05-06

    An apparatus for shaping, sharpening and polishing diamond-tipped single-point machine tools. The isolation of a rotating grinding wheel from its driving apparatus using an air bearing and causing the tool to be shaped, polished or sharpened to be moved across the surface of the grinding wheel so that it does not remain at one radius for more than a single rotation of the grinding wheel has been found to readily result in machine tools of a quality which can only be obtained by the most tedious and costly processing procedures, and previously unattainable by simple lapping techniques.

  8. Stirling machine operating experience

    SciTech Connect (OSTI)

    Ross, B.; Dudenhoefer, J.E.

    1994-09-01

    Numerous Stirling machines have been built and operated, but the operating experience of these machines is not well known. It is important to examine this operating experience in detail, because it largely substantiates the claim that stirling machines are capable of reliable and lengthy operating lives. The amount of data that exists is impressive, considering that many of the machines that have been built are developmental machines intended to show proof of concept, and are not expected to operate for lengthy periods of time. Some Stirling machines (typically free-piston machines) achieve long life through non-contact bearings, while other Stirling machines (typically kinematic) have achieved long operating lives through regular seal and bearing replacements. In addition to engine and system testing, life testing of critical components is also considered. The record in this paper is not complete, due to the reluctance of some organizations to release operational data and because several organizations were not contacted. The authors intend to repeat this assessment in three years, hoping for even greater participation.

  9. MACHINE AND FOUNDRY COMPANY

    Office of Legacy Management (LM)

    Machine & Fouudq Co., i3ue Termlual. Office ;s& ' PRI?sI?,NT: S. P:Chartland - DuPont D. B. Craxford - AW ..x.i "7.7, J. J* Crata - LHF 1, . ..( . . . . ,.- ., : pURPOSs ...

  10. Data Machine Independence

    Energy Science and Technology Software Center (OSTI)

    1994-12-30

    Data-machine independence achieved by using four technologies (ASN.1, XDR, SDS, and ZEBRA) has been evaluated by encoding two different applications in each of the above; and their results compared against the standard programming method using C.

  11. Sealing intersecting vane machines

    DOE Patents [OSTI]

    Martin, Jedd N.; Chomyszak, Stephen M.

    2007-06-05

    The invention provides a toroidal intersecting vane machine incorporating intersecting rotors to form primary and secondary chambers whose porting configurations minimize friction and maximize efficiency. Specifically, it is an object of the invention to provide a toroidal intersecting vane machine that greatly reduces the frictional losses through intersecting surfaces without the need for external gearing by modifying the width of one or both tracks at the point of intermeshing. The inventions described herein relate to these improvements.

  12. Sealing intersecting vane machines

    DOE Patents [OSTI]

    Martin, Jedd N.; Chomyszak, Stephen M.

    2005-06-07

    The invention provides a toroidal intersecting vane machine incorporating intersecting rotors to form primary and secondary chambers whose porting configurations minimize friction and maximize efficiency. Specifically, it is an object of the invention to provide a toroidal intersecting vane machine that greatly reduces the frictional losses through intersecting surfaces without the need for external gearing by modifying the width of one or both tracks at the point of intermeshing. The inventions described herein relate to these improvements.

  13. Human-machine interactions

    DOE Patents [OSTI]

    Forsythe, J. Chris; Xavier, Patrick G.; Abbott, Robert G.; Brannon, Nathan G.; Bernard, Michael L.; Speed, Ann E.

    2009-04-28

    Digital technology utilizing a cognitive model based on human naturalistic decision-making processes, including pattern recognition and episodic memory, can reduce the dependency of human-machine interactions on the abilities of a human user and can enable a machine to more closely emulate human-like responses. Such a cognitive model can enable digital technology to use cognitive capacities fundamental to human-like communication and cooperation to interact with humans.

  14. Metalworking and machining fluids

    DOE Patents [OSTI]

    Erdemir, Ali; Sykora, Frank; Dorbeck, Mark

    2010-10-12

    Improved boron-based metal working and machining fluids. Boric acid and boron-based additives that, when mixed with certain carrier fluids, such as water, cellulose and/or cellulose derivatives, polyhydric alcohol, polyalkylene glycol, polyvinyl alcohol, starch, dextrin, in solid and/or solvated forms result in improved metalworking and machining of metallic work pieces. Fluids manufactured with boric acid or boron-based additives effectively reduce friction, prevent galling and severe wear problems on cutting and forming tools.

  15. Extreme ultraviolet lithography machine

    DOE Patents [OSTI]

    Tichenor, Daniel A.; Kubiak, Glenn D.; Haney, Steven J.; Sweeney, Donald W.

    2000-01-01

    An extreme ultraviolet lithography (EUVL) machine or system for producing integrated circuit (IC) components, such as transistors, formed on a substrate. The EUVL machine utilizes a laser plasma point source directed via an optical arrangement onto a mask or reticle which is reflected by a multiple mirror system onto the substrate or target. The EUVL machine operates in the 10-14 nm wavelength soft x-ray photon. Basically the EUV machine includes an evacuated source chamber, an evacuated main or project chamber interconnected by a transport tube arrangement, wherein a laser beam is directed into a plasma generator which produces an illumination beam which is directed by optics from the source chamber through the connecting tube, into the projection chamber, and onto the reticle or mask, from which a patterned beam is reflected by optics in a projection optics (PO) box mounted in the main or projection chamber onto the substrate. In one embodiment of a EUVL machine, nine optical components are utilized, with four of the optical components located in the PO box. The main or projection chamber includes vibration isolators for the PO box and a vibration isolator mounting for the substrate, with the main or projection chamber being mounted on a support structure and being isolated.

  16. Experimental Approach of a High Performance Control of Two PermanentMagnet Synchronous Machines in an Integrated Drive for Automotive Applications

    SciTech Connect (OSTI)

    Tang, Lixin; Su, Gui-Jia

    2006-01-01

    The close-loop digital signal processor (DSP) control of an integrated-dual inverter, which is able to drive two permanent magnet (PM) motors independently, is presented and evaluated experimentally. By utilizing the neutral point of the main traction motor, only two inverter poles are needed for the two-phase auxiliary motor. The modified field-oriented control scheme for this integrated inverter was introduced and employed in real-time control. The experimental results show the inverter is able to control two drives independently. An integrated, component count reduced drive is achieved.

  17. Micro-machined resonator

    DOE Patents [OSTI]

    Godshall, N.A.; Koehler, D.R.; Liang, A.Y.; Smith, B.K.

    1993-03-30

    A micro-machined resonator, typically quartz, with upper and lower micro-machinable support members, or covers, having etched wells which may be lined with conductive electrode material, between the support members is a quartz resonator having an energy trapping quartz mesa capacitively coupled to the electrode through a diaphragm; the quartz resonator is supported by either micro-machined cantilever springs or by thin layers extending over the surfaces of the support. If the diaphragm is rigid, clock applications are available, and if the diaphragm is resilient, then transducer applications can be achieved. Either the thin support layers or the conductive electrode material can be integral with the diaphragm. In any event, the covers are bonded to form a hermetic seal and the interior volume may be filled with a gas or may be evacuated. In addition, one or both of the covers may include oscillator and interface circuitry for the resonator.

  18. Micro-machined resonator

    DOE Patents [OSTI]

    Godshall, Ned A.; Koehler, Dale R.; Liang, Alan Y.; Smith, Bradley K.

    1993-01-01

    A micro-machined resonator, typically quartz, with upper and lower micro-machinable support members, or covers, having etched wells which may be lined with conductive electrode material, between the support members is a quartz resonator having an energy trapping quartz mesa capacitively coupled to the electrode through a diaphragm; the quartz resonator is supported by either micro-machined cantilever springs or by thin layers extending over the surfaces of the support. If the diaphragm is rigid, clock applications are available, and if the diaphragm is resilient, then transducer applications can be achieved. Either the thin support layers or the conductive electrode material can be integral with the diaphragm. In any event, the covers are bonded to form a hermetic seal and the interior volume may be filled with a gas or may be evacuated. In addition, one or both of the covers may include oscillator and interface circuitry for the resonator.

  19. MACHINE AND FOUNDRY COMPANY

    Office of Legacy Management (LM)

    MACHINE AND FOUNDRY COMPANY kt '- : :'~ ENGINEERING DIVISIOJ ---. Cl FIELD iRIP ,REP@?T ,' ~ i;~:z;~zy~ MEETING REPORT : .I.-.-' ~Y ::,:I :. &, .I7 ENGINEERING REPORT- : $T, ~ suBJ:m~i-c n-..*~~.~n~ 9r.1 _ P,Y.~.I~ ADDRESS: :'~.'"I .- .._ c. Plans for - ,:, ..-; .:.j s ,PERSON CONTACTED . . .' ., I : /LV cliq 22: PLPCZS w: - American Machine & Fouudq Co., i3ue Termlual. Office ;s& $' PRI?sI?,NT: S. P~:Chartland - DuPont D. B. Craxford - AW ..x.i "7.7, J. J* Crata - LHF 1, .

  20. Automated fiber pigtailing machine

    DOE Patents [OSTI]

    Strand, O.T.; Lowry, M.E.

    1999-01-05

    The Automated Fiber Pigtailing Machine (AFPM) aligns and attaches optical fibers to optoelectronic (OE) devices such as laser diodes, photodiodes, and waveguide devices without operator intervention. The so-called pigtailing process is completed with sub-micron accuracies in less than 3 minutes. The AFPM operates unattended for one hour, is modular in design and is compatible with a mass production manufacturing environment. This machine can be used to build components which are used in military aircraft navigation systems, computer systems, communications systems and in the construction of diagnostics and experimental systems. 26 figs.

  1. Automated fiber pigtailing machine

    DOE Patents [OSTI]

    Strand, Oliver T.; Lowry, Mark E.

    1999-01-01

    The Automated Fiber Pigtailing Machine (AFPM) aligns and attaches optical fibers to optoelectonic (OE) devices such as laser diodes, photodiodes, and waveguide devices without operator intervention. The so-called pigtailing process is completed with sub-micron accuracies in less than 3 minutes. The AFPM operates unattended for one hour, is modular in design and is compatible with a mass production manufacturing environment. This machine can be used to build components which are used in military aircraft navigation systems, computer systems, communications systems and in the construction of diagnostics and experimental systems.

  2. Intersecting vane machines

    DOE Patents [OSTI]

    Bailey, H. Sterling; Chomyszak, Stephen M.

    2007-01-16

    The invention provides a toroidal intersecting vane machine incorporating intersecting rotors to form primary and secondary chambers whose porting configurations minimize friction and maximize efficiency. Specifically, it is an object of the invention to provide a toroidal intersecting vane machine that greatly reduces the frictional losses through meshing surfaces without the need for external gearing by modifying the function of one or the other of the rotors from that of "fluid moving" to that of "valving" thereby reducing the pressure loads and associated inefficiencies at the interface of the meshing surfaces. The inventions described herein relate to these improvements.

  3. Precision Robotic Assembly Machine

    ScienceCinema (OSTI)

    None

    2010-09-01

    The world's largest laser system is the National Ignition Facility (NIF), located at Lawrence Livermore National Laboratory. NIF's 192 laser beams are amplified to extremely high energy, and then focused onto a tiny target about the size of a BB, containing frozen hydrogen gas. The target must be perfectly machined to incredibly demanding specifications. The Laboratory's scientists and engineers have developed a device called the "Precision Robotic Assembly Machine" for this purpose. Its unique design won a prestigious R&D-100 award from R&D Magazine.

  4. Laser machining of explosives

    DOE Patents [OSTI]

    Perry, Michael D.; Stuart, Brent C.; Banks, Paul S.; Myers, Booth R.; Sefcik, Joseph A.

    2000-01-01

    The invention consists of a method for machining (cutting, drilling, sculpting) of explosives (e.g., TNT, TATB, PETN, RDX, etc.). By using pulses of a duration in the range of 5 femtoseconds to 50 picoseconds, extremely precise and rapid machining can be achieved with essentially no heat or shock affected zone. In this method, material is removed by a nonthermal mechanism. A combination of multiphoton and collisional ionization creates a critical density plasma in a time scale much shorter than electron kinetic energy is transferred to the lattice. The resulting plasma is far from thermal equilibrium. The material is in essence converted from its initial solid-state directly into a fully ionized plasma on a time scale too short for thermal equilibrium to be established with the lattice. As a result, there is negligible heat conduction beyond the region removed resulting in negligible thermal stress or shock to the material beyond a few microns from the laser machined surface. Hydrodynamic expansion of the plasma eliminates the need for any ancillary techniques to remove material and produces extremely high quality machined surfaces. There is no detonation or deflagration of the explosive in the process and the material which is removed is rendered inert.

  5. Substantially Parallel Flux Uncluttered Rotor Machines (U-Machine) - Energy

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Innovation Portal Substantially Parallel Flux Uncluttered Rotor Machines (U-Machine) Oak Ridge National Laboratory Contact ORNL About This Technology Projected performance/speed characteristics of the novel U-machine motor Projected performance/speed characteristics of the novel U-machine motor Technology Marketing SummaryA general concern based on the supply and demand trend of the permanent magnet (PM) raw materials suggests the need for elimination of these materials from electric motors

  6. Clean Cast Steel Technology - Machinability and Technology Transfer

    SciTech Connect (OSTI)

    C. E. Bates; J. A. Griffin

    2000-05-01

    There were two main tasks in the Clean Cast Steel Technology - Machinability and Technology Transfer Project. These were (1) determine the processing facts that control the machinability of cast steel and (2) determine the ability of ladle stirring to homogenize ladle temperature, reduce the tap and pouring temperatures, and reduce casting scrap.

  7. Agile Machining and Inspection Non-Nuclear Report (NNR) Project

    SciTech Connect (OSTI)

    Lazarus, Lloyd

    2009-02-19

    This report is a high level summary of the eight major projects funded by the Agile Machining and Inspection Non-Nuclear Readiness (NNR) project (FY06.0422.3.04.R1). The largest project of the group is the Rapid Response project in which the six major sub categories are summarized. This project focused on the operations of the machining departments that will comprise Special Applications Machining (SAM) in the Kansas City Responsive Infrastructure Manufacturing & Sourcing (KCRIMS) project. This project was aimed at upgrading older machine tools, developing new inspection tools, eliminating Classified Removable Electronic Media (CREM) in the handling of classified Numerical Control (NC) programs by installing the CRONOS network, and developing methods to automatically load Coordinated-Measuring Machine (CMM) inspection data into bomb books and product score cards. Finally, the project personnel leaned perations of some of the machine tool cells, and now have the model to continue this activity.

  8. Brilliant Machines | GE Global Research

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    new window) Click to share on Tumblr (Opens in new window) Brilliant Machines Bradford Miller 2014.05.21 Are the machines of tomorrow really different from what we have now? Closed...

  9. Micro-machined resonator oscillator

    DOE Patents [OSTI]

    Koehler, D.R.; Sniegowski, J.J.; Bivens, H.M.; Wessendorf, K.O.

    1994-08-16

    A micro-miniature resonator-oscillator is disclosed. Due to the miniaturization of the resonator-oscillator, oscillation frequencies of one MHz and higher are utilized. A thickness-mode quartz resonator housed in a micro-machined silicon package and operated as a telemetered sensor beacon'' that is, a digital, self-powered, remote, parameter measuring-transmitter in the FM-band. The resonator design uses trapped energy principles and temperature dependence methodology through crystal orientation control, with operation in the 20--100 MHz range. High volume batch-processing manufacturing is utilized, with package and resonator assembly at the wafer level. Unique design features include squeeze-film damping for robust vibration and shock performance, capacitive coupling through micro-machined diaphragms allowing resonator excitation at the package exterior, circuit integration and extremely small (0.1 in. square) dimensioning. A family of micro-miniature sensor beacons is also disclosed with widespread applications as bio-medical sensors, vehicle status monitors and high-volume animal identification and health sensors. The sensor family allows measurement of temperatures, chemicals, acceleration and pressure. A microphone and clock realization is also available. 21 figs.

  10. Micro-machined resonator oscillator

    DOE Patents [OSTI]

    Koehler, Dale R.; Sniegowski, Jeffry J.; Bivens, Hugh M.; Wessendorf, Kurt O.

    1994-01-01

    A micro-miniature resonator-oscillator is disclosed. Due to the miniaturization of the resonator-oscillator, oscillation frequencies of one MHz and higher are utilized. A thickness-mode quartz resonator housed in a micro-machined silicon package and operated as a "telemetered sensor beacon" that is, a digital, self-powered, remote, parameter measuring-transmitter in the FM-band. The resonator design uses trapped energy principles and temperature dependence methodology through crystal orientation control, with operation in the 20-100 MHz range. High volume batch-processing manufacturing is utilized, with package and resonator assembly at the wafer level. Unique design features include squeeze-film damping for robust vibration and shock performance, capacitive coupling through micro-machined diaphragms allowing resonator excitation at the package exterior, circuit integration and extremely small (0.1 in. square) dimensioning. A family of micro-miniature sensor beacons is also disclosed with widespread applications as bio-medical sensors, vehicle status monitors and high-volume animal identification and health sensors. The sensor family allows measurement of temperatures, chemicals, acceleration and pressure. A microphone and clock realization is also available.

  11. Diagnostics for machine protection of DEMO

    SciTech Connect (OSTI)

    Felton, R.

    2014-08-21

    DEMO aims to (i) integrate, demonstrate and validate all relevant technology necessary to convert fusion energy to electrical energy and (ii) that the machine and its operations are economically and environmentally acceptable. To maintain the efficiency and availability of the machine, there are several physics and combined physics/technology issues as well as the engineering issues. Machine Protection (also known as Protection of Investment) addresses both the risks to plant (to avoid costly repair or replacement) and the risks to normal operating time (to avoid loss of productivity and the return on investment). The plasma-related Machine Protection issues involve measurement and control of plasma stability, plasma purity, and plasma-wall interactions. Machine Protection aims to avoid hitting catastrophic limits by using early warning alarm systems, and controlled termination or avoidance, involving coordinated actions of the magnets, gas and auxiliary heating or current-drive systems. This article outlines the key processes, some of which are used in present-day tokamaks and some of which are new specifically for DEMO (e.g. First wall and divertor power handling) and reveals the need to research and develop new science and technology for Machine Protections in DEMO's high radiation and thermal fields. This work was funded by the RCUK Energy Programme under grant EP/I501045 and the European Communities under the contract of Association between EURATOM and CCFE and conducted partly under EFDA PPPT (WP13-DAS04). The views and opinions expressed herein do not necessarily reflect those of the European Commission.

  12. Z Machine | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    Confinement Fusion ICF Facilities Z Machine Z Machine Air-gas breakdown when Z Machine at Sandia National Laboratories fires. The Z Machine is a pulsed power driver that ...

  13. Programmable phase plate for tool modification in laser machining applications

    DOE Patents [OSTI]

    Thompson Jr., Charles A.; Kartz, Michael W.; Brase, James M.; Pennington, Deanna; Perry, Michael D.

    2004-04-06

    A system for laser machining includes a laser source for propagating a laser beam toward a target location, and a spatial light modulator having individual controllable elements capable of modifying a phase profile of the laser beam to produce a corresponding irradiance pattern on the target location. The system also includes a controller operably connected to the spatial light modulator for controlling the individual controllable elements. By controlling the individual controllable elements, the phase profile of the laser beam may be modified into a desired phase profile so as to produce a corresponding desired irradiance pattern on the target location capable of performing a machining operation on the target location.

  14. Machine for applying a two component resin to a roadway surface

    DOE Patents [OSTI]

    Huszagh, Donald W.

    1985-01-01

    A portable machine for spraying two component resins onto a roadway, the machine having a pneumatic control system, including apparatus for purging the machine of mixed resin with air and then removing remaining resin with solvent. Interlocks prevent contamination of solvent and resin, and mixed resin can be purged in the event of a power failure.

  15. Machine for applying a two component resin to a roadway surface

    DOE Patents [OSTI]

    Huszagh, D.W.

    1984-01-01

    A portable machine for spraying two component resins onto a roadway, the machine having a pneumatic control system, including means for purging the machine of mixed resin with air and then removing remaining resin with solvent. Interlocks prevent contamination of solvent and resin, and mixed resin can be purged in the event of a power failure.

  16. Quantification of uncertainty in machining operations for on-machine acceptance.

    SciTech Connect (OSTI)

    Claudet, Andre A.; Tran, Hy D.; Su, Jiann-Chemg

    2008-09-01

    Manufactured parts are designed with acceptance tolerances, i.e. deviations from ideal design conditions, due to unavoidable errors in the manufacturing process. It is necessary to measure and evaluate the manufactured part, compared to the nominal design, to determine whether the part meets design specifications. The scope of this research project is dimensional acceptance of machined parts; specifically, parts machined using numerically controlled (NC, or also CNC for Computer Numerically Controlled) machines. In the design/build/accept cycle, the designer will specify both a nominal value, and an acceptable tolerance. As part of the typical design/build/accept business practice, it is required to verify that the part did meet acceptable values prior to acceptance. Manufacturing cost must include not only raw materials and added labor, but also the cost of ensuring conformance to specifications. Ensuring conformance is a substantial portion of the cost of manufacturing. In this project, the costs of measurements were approximately 50% of the cost of the machined part. In production, cost of measurement would be smaller, but still a substantial proportion of manufacturing cost. The results of this research project will point to a science-based approach to reducing the cost of ensuring conformance to specifications. The approach that we take is to determine, a priori, how well a CNC machine can manufacture a particular geometry from stock. Based on the knowledge of the manufacturing process, we are then able to decide features which need further measurements from features which can be accepted 'as is' from the CNC. By calibration of the machine tool, and establishing a machining accuracy ratio, we can validate the ability of CNC to fabricate to a particular level of tolerance. This will eliminate the costs of checking for conformance for relatively large tolerances.

  17. CENTRIFUGAL CASTING MACHINE

    DOE Patents [OSTI]

    Shuck, A.B.

    1958-04-01

    A device is described that is specifically designed to cast uraniumn fuel rods in a vacuunn, in order to obtain flawless, nonoxidized castings which subsequently require a maximum of machining or wastage of the expensive processed material. A chamber surrounded with heating elements is connected to the molds, and the entire apparatus is housed in an airtight container. A charge of uranium is placed in the chamber, heated, then is allowed to flow into the molds While being rotated. Water circulating through passages in the molds chills the casting to form a fine grained fuel rod in nearly finished form.

  18. Stirling cycle machine

    SciTech Connect (OSTI)

    Burnett, S.C.; Purcell, J.R.; Creedon, W.P.; Joshi, C.H.

    1990-06-05

    This patent describes an improvement in a Stirling cycle machine including first and second variable-volume, compression-expansion chambers containing a gas a regenerator interconnecting the chambers and for conducting the gas therebetween, and eccentric drive means for driving the first and second chambers. It comprises: the eccentric drive means comprising a pair of rotatably mounted shafts, at least one pair of eccentric disks fixed on the shafts in phase with each other, and means for causing the shafts and thereby the eccentric disks to rotate in opposite directions.

  19. Joint environmental assessment 1997--2001 of the California Department of Food and Agriculture Curly Top Virus Control Program for Bureau of Land Management and Department of Energy

    SciTech Connect (OSTI)

    1997-03-01

    The DOE, Naval Petroleum reserves in California (NPRC), proposes to sign an Amendment to the Cooperative Agreement and Supplement with the California Department of Food and Agriculture (CDFA) to extend the term of the Curly Top Virus Control Program (CTVCP) in California. This program involves Malathion spraying on NPRC lands to control the beet leafhopper, over a five year period from 1997 through 2001. It is expected that approximately 330 acres on Naval Petroleum Reserve Number 1 (NPR-1) and approximately 9,603 acres on Naval Petroleum Reserve Number 2 (NPR-2) will be treated with Malathion annually by CDFA during the course of this program. The actual acreage subject to treatment can vary from year to year. Pursuant to the requirements of the National Environmental Policy Act of 1969 (NEPA), as amended, the potential impacts of the proposed action were analyzed in a Joint Environmental Assessment (DOE/EA-1011) with the US Department of Interior, Bureau of Land Management (BLM) acting as lead agency, in consultation with the CDFA, and the DOE acting as a cooperating agency. Based on the analysis in the EA, DOE has determined that the conduct of the Curly Top Virus Control Program in California is not a major Federal action significantly affecting the quality of the human environment, within the meaning of the NEPA. Therefore, the preparation of an Environmental Impact Statement is not required and DOE is consequently issuing a FONSI.

  20. Estimated general population control limits for unitary agents in drinking water, milk, soil, and unprocessed food items. For use in reentry decision-making

    SciTech Connect (OSTI)

    Watson, A.P.; Adams, J.D.; Cerar, R.J.; Hess, T.L.; Kistner, S.L.; Leffingwell, S.S.; MacIntosh, R.G.; Ward, J.R.

    1992-01-01

    In the event of an unplanned release of chemical agent during any stage of the Chemical Stockpile Disposal Program (CSDP), the potential exists for contamination of drinking water, forage crops, grains, garden produce, and livestock. Persistent agents such as VX or sulfur mustard pose the greatest human health concern for reentry. This White Paper has been prepared to provide technical bases for these decisions by developing working estimates of agent control limits in selected environmental media considered principal sources of potential human exposure. To date, control limits for public exposure to unitary agents have been established for atmospheric concentrations only. The current analysis builds on previous work to calculate working estimates of control limits for ingestion and dermal exposure to potentially contaminated drinking water, milk, soil, and unprocessed food items such as garden produce. Information characterizing agent desorption from, and detection on or in, contaminated porous media are presently too developed to permit reasonable estimation of dermal exposure from this source. Thus, dermal contact with potentially contaminated porous surfaces is not considered in this document.

  1. Mysteries of 'molecular machines' revealed

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Mysteries of 'molecular machines' revealed Mysteries of 'molecular machines' revealed Scientists are making it easier for pharmaceutical companies and researchers to see the detailed inner workings of molecular machines. December 22, 2014 A picture of a membrane protein called cysZ determined with Phenix software using data that could not previously be analyzed. A picture of a membrane protein called cysZ determined with Phenix software using data that could not previously be analyzed. Contact

  2. Green Machine | Open Energy Information

    Open Energy Info (EERE)

    Information Name Green Machine Facility Geothermal Power Plant Sector Geothermal energy Location Information Coordinates 45.943161, 24.96676 Loading map......

  3. Positional reference system for ultraprecision machining

    DOE Patents [OSTI]

    Arnold, Jones B.; Burleson, Robert R.; Pardue, Robert M.

    1982-01-01

    A stable positional reference system for use in improving the cutting tool-to-part contour position in numerical controlled-multiaxis metal turning machines is provided. The reference system employs a plurality of interferometers referenced to orthogonally disposed metering bars which are substantially isolated from machine strain induced position errors for monitoring the part and tool positions relative to the metering bars. A microprocessor-based control system is employed in conjunction with the plurality of position interferometers and part contour description data inputs to calculate error components for each axis of movement and output them to corresponding axis drives with appropriate scaling and error compensation. Real-time position control, operating in combination with the reference system, makes possible the positioning of the cutting points of a tool along a part locus with a substantially greater degree of accuracy than has been attained previously in the art by referencing and then monitoring only the tool motion relative to a reference position located on the machine base.

  4. Positional reference system for ultraprecision machining

    DOE Patents [OSTI]

    Arnold, J.B.; Burleson, R.R.; Pardue, R.M.

    1980-09-12

    A stable positional reference system for use in improving the cutting tool-to-part contour position in numerical controlled-multiaxis metal turning machines is provided. The reference system employs a plurality of interferometers referenced to orthogonally disposed metering bars which are substantially isolated from machine strain induced position errors for monitoring the part and tool positions relative to the metering bars. A microprocessor-based control system is employed in conjunction with the plurality of positions interferometers and part contour description data input to calculate error components for each axis of movement and output them to corresponding axis driven with appropriate scaling and error compensation. Real-time position control, operating in combination with the reference system, makes possible the positioning of the cutting points of a tool along a part locus with a substantially greater degree of accuracy than has been attained previously in the art by referencing and then monitoring only the tool motion relative to a reference position located on the machine base.

  5. Vending Machine Controls | Open Energy Information

    Open Energy Info (EERE)

    Contact needs updating Image needs updating Reference needed Missing content Broken link Other Additional Comments Cancel Submit Category: Articles with outstanding TODO tasks...

  6. NREL: Transportation Research - Power Electronics and Electric Machines

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Electric Machines A photo of a researcher using testing equipment in a lab. NREL R&D is making wide-scale adoption of electric-drive vehicles more feasible by developing technologies and components with superior reliability, efficiency, and durability, while dramatically decreasing costs. Photo by Dennis Schroeder, NREL NREL's power electronics and electric machines research focuses on systems for electric-drive vehicles (EDVs) that control the flow of electricity between the battery, the

  7. Hybrid-secondary uncluttered induction machine

    DOE Patents [OSTI]

    Hsu, John S.

    2001-01-01

    An uncluttered secondary induction machine (100) includes an uncluttered rotating transformer (66) which is mounted on the same shaft as the rotor (73) of the induction machine. Current in the rotor (73) is electrically connected to current in the rotor winding (67) of the transformer, which is not electrically connected to, but is magnetically coupled to, a stator secondary winding (40). The stator secondary winding (40) is alternately connected to an effective resistance (41), an AC source inverter (42) or a magnetic switch (43) to provide a cost effective slip-energy-controlled, adjustable speed, induction motor that operates over a wide speed range from below synchronous speed to above synchronous speed based on the AC line frequency fed to the stator.

  8. Methods, systems and apparatus for synchronous current regulation of a five-phase machine

    DOE Patents [OSTI]

    Gallegos-Lopez, Gabriel; Perisic, Milun

    2012-10-09

    Methods, systems and apparatus are provided for controlling operation of and regulating current provided to a five-phase machine when one or more phases has experienced a fault or has failed. In one implementation, the disclosed embodiments can be used to synchronously regulate current in a vector controlled motor drive system that includes a five-phase AC machine, a five-phase inverter module coupled to the five-phase AC machine, and a synchronous current regulator.

  9. Slide system for machine tools

    DOE Patents [OSTI]

    Douglass, S.S.; Green, W.L.

    1980-06-12

    The present invention relates to a machine tool which permits the machining of nonaxisymmetric surfaces on a workpiece while rotating the workpiece about a central axis of rotation. The machine tool comprises a conventional two-slide system (X-Y) with one of these slides being provided with a relatively short travel high-speed auxiliary slide which carries the material-removing tool. The auxiliary slide is synchronized with the spindle speed and the position of the other two slides and provides a high-speed reciprocating motion required for the displacement of the cutting tool for generating a nonaxisymmetric surface at a selected location on the workpiece.

  10. Victory Power Machine Group | Open Energy Information

    Open Energy Info (EERE)

    Machine Group Jump to: navigation, search Name: Victory Power Machine Group Place: Dongying, Shandong Province, China Zip: 257032 Product: the biggest equipment manufacture of...

  11. Soil Machine Dynamics Ltd | Open Energy Information

    Open Energy Info (EERE)

    Machine Dynamics Ltd Jump to: navigation, search Name: Soil Machine Dynamics Ltd Region: United Kingdom Sector: Marine and Hydrokinetic Website: http: This company is listed in the...

  12. Machine Status | Argonne Leadership Computing Facility

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    User Support User Support Machine Status Presentations Training & Outreach User Survey Machine Status MIRA 0 CETUS 0 VESTA 0 TUKEY 0...

  13. Fuzzy logic controller optimization

    DOE Patents [OSTI]

    Sepe, Jr., Raymond B; Miller, John Michael

    2004-03-23

    A method is provided for optimizing a rotating induction machine system fuzzy logic controller. The fuzzy logic controller has at least one input and at least one output. Each input accepts a machine system operating parameter. Each output produces at least one machine system control parameter. The fuzzy logic controller generates each output based on at least one input and on fuzzy logic decision parameters. Optimization begins by obtaining a set of data relating each control parameter to at least one operating parameter for each machine operating region. A model is constructed for each machine operating region based on the machine operating region data obtained. The fuzzy logic controller is simulated with at least one created model in a feedback loop from a fuzzy logic output to a fuzzy logic input. Fuzzy logic decision parameters are optimized based on the simulation.

  14. State machine analysis of sensor data from dynamic processes

    DOE Patents [OSTI]

    Cook, William R.; Brabson, John M.; Deland, Sharon M.

    2003-12-23

    A state machine model analyzes sensor data from dynamic processes at a facility to identify the actual processes that were performed at the facility during a period of interest for the purpose of remote facility inspection. An inspector can further input the expected operations into the state machine model and compare the expected, or declared, processes to the actual processes to identify undeclared processes at the facility. The state machine analysis enables the generation of knowledge about the state of the facility at all levels, from location of physical objects to complex operational concepts. Therefore, the state machine method and apparatus may benefit any agency or business with sensored facilities that stores or manipulates expensive, dangerous, or controlled materials or information.

  15. Process for laser machining and surface treatment

    DOE Patents [OSTI]

    Neil, George R.; Shinn, Michelle D.

    2004-10-26

    An improved method and apparatus increasing the accuracy and reducing the time required to machine materials, surface treat materials, and allow better control of defects such as particulates in pulsed laser deposition. The speed and quality of machining is improved by combining an ultrashort pulsed laser at high average power with a continuous wave laser. The ultrashort pulsed laser provides an initial ultrashort pulse, on the order of several hundred femtoseconds, to stimulate an electron avalanche in the target material. Coincident with the ultrashort pulse or shortly after it, a pulse from a continuous wave laser is applied to the target. The micromachining method and apparatus creates an initial ultrashort laser pulse to ignite the ablation followed by a longer laser pulse to sustain and enlarge on the ablation effect launched in the initial pulse. The pulse pairs are repeated at a high pulse repetition frequency and as often as desired to produce the desired micromachining effect. The micromachining method enables a lower threshold for ablation, provides more deterministic damage, minimizes the heat affected zone, minimizes cracking or melting, and reduces the time involved to create the desired machining effect.

  16. biomass briquetting machine | OpenEI Community

    Open Energy Info (EERE)

    biomass briquetting machine Home There are currently no posts in this category. Syndicate content...

  17. Food Sales Buildings

    U.S. Energy Information Administration (EIA) Indexed Site

    Sales Characteristics by Activity... Food Sales Food sales buildings are buildings that are used for retail or wholesale sale of food. Basic Characteristics See also: Equipment |...

  18. Baseline Test Specimen Machining Report

    SciTech Connect (OSTI)

    mark Carroll

    2009-08-01

    The Next Generation Nuclear Plant (NGNP) Project is tasked with selecting a high temperature gas reactor technology that will be capable of generating electricity and supplying large amounts of process heat. The NGNP is presently being designed as a helium-cooled high temperature gas reactor (HTGR) with a large graphite core. The graphite baseline characterization project is conducting the research and development (R&D) activities deemed necessary to fully qualify nuclear-grade graphite for use in the NGNP reactor. Establishing nonirradiated thermomechanical and thermophysical properties by characterizing lot-to-lot and billet-to-billet variations (for probabilistic baseline data needs) through extensive data collection and statistical analysis is one of the major fundamental objectives of the project. The reactor core will be made up of stacks of graphite moderator blocks. In order to gain a more comprehensive understanding of the varying characteristics in a wide range of suitable graphites, any of which can be classified as “nuclear grade,” an experimental program has been initiated to develop an extensive database of the baseline characteristics of numerous candidate graphites. Various factors known to affect the properties of graphite will be investigated, including specimen size, spatial location within a graphite billet, specimen orientation within a billet (either parallel to [P] or transverse to [T] the long axis of the as-produced billet), and billet-to-billet variations within a lot or across different production lots. Because each data point is based on a certain position within a given billet of graphite, particular attention must be paid to the traceability of each specimen and its spatial location and orientation within each billet. The evaluation of these properties is discussed in the Graphite Technology Development Plan (Windes et. al, 2007). One of the key components in the evaluation of these graphite types will be mechanical testing on specimens drawn from carefully controlled sections of each billet. To this end, this report will discuss the machining of the first set of test specimens that will be evaluated in this program through tensile, compressive, and flexural testing. Validation that the test specimens have been produced to the tolerances required by the applicable ASTM standards, and to the quality control levels required by this program, will demonstrate the viability of sending graphite to selected suppliers that will provide valuable and certifiable data to future data sets that are integral to the NGNP program and beyond.

  19. Thin seam mining machine

    SciTech Connect (OSTI)

    Nelson, R.L.

    1984-05-22

    A low profile thin seam miner includes a main frame mounting a lower transverse axis rotary cutter and a parallel axis conveyor rearwardly of the lower cutter. The main frame also mounts a forward transverse axis rotary cutter somewhat above the lower cutter, the forward upper cutter being supported on a longitudinal boom pivoted to the main frame and being vertically swingable under influence of a single cylinder. The main frame and all of its parts is incrementally advanced into the seam by the alternating action of two horizontal longitudinal parallel axis cylinders connected between the main frame and a pair of floor-engaging plates. Two vertical axis jacks are connected between the two floor-engaging plates and two cooperating overhead roof plates, connected with the floor-engaging plates by separate toggle linkages. Two more generally upright cylinders connected between the floor plates and the rear of the main frame can tilt the main frame on a transverse pivot axis to vary the depth of cut of the lower rear cutter responsive to the control of a sensing tooth on such cutter. The single cylinder connected with the boom of the forward upper cutter can swing the boom on its transverse pivot axis to vary the depth of cut of the forward upper cutter, responsive to the control of a sensing tooth on such cutter.

  20. Axial gap rotating electrical machine

    DOE Patents [OSTI]

    None

    2016-02-23

    Direct drive rotating electrical machines with axial air gaps are disclosed. In these machines, a rotor ring and stator ring define an axial air gap between them. Sets of gap-maintaining rolling supports bear between the rotor ring and the stator ring at their peripheries to maintain the axial air gap. Also disclosed are wind turbines using these generators, and structures and methods for mounting direct drive rotating electrical generators to the hubs of wind turbines. In particular, the rotor ring of the generator may be carried directly by the hub of a wind turbine to rotate relative to a shaft without being mounted directly to the shaft.

  1. Cooling system for rotating machine

    DOE Patents [OSTI]

    Gerstler, William Dwight; El-Refaie, Ayman Mohamed Fawzi; Lokhandwalla, Murtuza; Alexander, James Pellegrino; Quirion, Owen Scott; Palafox, Pepe; Shen, Xiaochun; Salasoo, Lembit

    2011-08-09

    An electrical machine comprising a rotor is presented. The electrical machine includes the rotor disposed on a rotatable shaft and defining a plurality of radial protrusions extending from the shaft up to a periphery of the rotor. The radial protrusions having cavities define a fluid path. A stationary shaft is disposed concentrically within the rotatable shaft wherein an annular space is formed between the stationary and rotatable shaft. A plurality of magnetic segments is disposed on the radial protrusions and the fluid path from within the stationary shaft into the annular space and extending through the cavities within the radial protrusions.

  2. Holiday Food Drive

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Food Drive Holiday Food Drive Laboratory employees helped donate 300 boxes of nonperishable food items and 360 frozen turkeys during the 2015 annual food drive. September 16, 2013 LANL employees organize food for the Holiday Food Drive. Contacts Annual Food & Holiday Gift Drives Mike Martinez (505) 699-3388 Community Relations & Partnerships (505) 665-4400 Email Helping feed Northern New Mexico families During the Laboratory's 2015 Annual Food Drive, employees and subcontract workers

  3. Cryogenic expansion machine

    DOE Patents [OSTI]

    Pallaver, Carl B.; Morgan, Michael W.

    1978-01-01

    A cryogenic expansion engine includes intake and exhaust poppet valves each controlled by a cam having adjustable dwell, the valve seats for the valves being threaded inserts in the valve block. Each cam includes a cam base and a ring-shaped cam insert disposed at an exterior corner of the cam base, the cam base and cam insert being generally circular but including an enlarged cam dwell, the circumferential configuration of the cam base and cam dwell being identical, the cam insert being rotatable with respect to the cam base. GI CONTRACTUAL ORIGIN OF THE INVENTION The invention described herein was made in the course of, or under, a contract with the UNITED STATES ENERGY RESEARCH AND DEVELOPMENT ADMINISTRATION.

  4. Mobile machine hazardous working zone warning system

    DOE Patents [OSTI]

    Schiffbauer, W.H.; Ganoe, C.W.

    1999-08-17

    A warning system is provided for a mobile working machine to alert an individual of a potentially dangerous condition in the event the individual strays into a hazardous working zone of the machine. The warning system includes a transmitter mounted on the machine and operable to generate a uniform magnetic field projecting beyond an outer periphery of the machine in defining a hazardous working zone around the machine during operation. A receiver, carried by the individual and activated by the magnetic field, provides an alarm signal to alert the individual when he enters the hazardous working zone of the machine. 3 figs.

  5. Mobile machine hazardous working zone warning system

    DOE Patents [OSTI]

    Schiffbauer, William H.; Ganoe, Carl W.

    1999-01-01

    A warning system is provided for a mobile working machine to alert an individual of a potentially dangerous condition in the event the individual strays into a hazardous working zone of the machine. The warning system includes a transmitter mounted on the machine and operable to generate a uniform magnetic field projecting beyond an outer periphery of the machine in defining a hazardous working zone around the machine during operation thereof. A receiver, carried by the individual and activated by the magnetic field, provides an alarm signal to alert the individual when he enters the hazardous working zone of the machine.

  6. Gelcasting compositions having improved drying characteristics and machinability

    DOE Patents [OSTI]

    Janney, Mark A.; Walls, Claudia A. H.

    2001-01-01

    A gelcasting composition has improved drying behavior, machinability and shelf life in the dried and unfired state. The composition includes an inorganic powder, solvent, monomer system soluble in the solvent, an initiator system for polymerizing the monomer system, and a plasticizer soluble in the solvent. Dispersants and other processing aides to control slurry properties can be added. The plasticizer imparts an ability to dry thick section parts, to store samples in the dried state without cracking under conditions of varying relative humidity, and to machine dry gelcast parts without cracking or chipping. A method of making gelcast parts is also disclosed.

  7. High-precision micro/nano-scale machining system

    DOE Patents [OSTI]

    Kapoor, Shiv G.; Bourne, Keith Allen; DeVor, Richard E.

    2014-08-19

    A high precision micro/nanoscale machining system. A multi-axis movement machine provides relative movement along multiple axes between a workpiece and a tool holder. A cutting tool is disposed on a flexible cantilever held by the tool holder, the tool holder being movable to provide at least two of the axes to set the angle and distance of the cutting tool relative to the workpiece. A feedback control system uses measurement of deflection of the cantilever during cutting to maintain a desired cantilever deflection and hence a desired load on the cutting tool.

  8. Aqueous cutting fluid for machining fissionable materials

    DOE Patents [OSTI]

    Duerksen, Walter K.; Googin, John M.; Napier, Jr., Bradley

    1984-01-01

    The present invention is directed to a cutting fluid for machining fissionable material. The cutting fluid is formed of glycol, water and boron compound in an adequate concentration for effective neutron attenuation so as to inhibit criticality incidents during machining.

  9. z machine | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    The Z Machine The Z Machine is a pulsed power driver that delivers enormous power in a short duration pulse to a small complex target at the center of the large (34 meters in ...

  10. Permutation parity machines for neural cryptography

    SciTech Connect (OSTI)

    Reyes, Oscar Mauricio; Zimmermann, Karl-Heinz

    2010-06-15

    Recently, synchronization was proved for permutation parity machines, multilayer feed-forward neural networks proposed as a binary variant of the tree parity machines. This ability was already used in the case of tree parity machines to introduce a key-exchange protocol. In this paper, a protocol based on permutation parity machines is proposed and its performance against common attacks (simple, geometric, majority and genetic) is studied.

  11. Evaluation Of Electrochemical Machining Technology For Surface...

    Office of Scientific and Technical Information (OSTI)

    Evaluation Of Electrochemical Machining Technology For Surface Improvements In Additive Manufactured Components ... ORNL Manufacturing Demonstration Facility worked with ECM ...

  12. Method and apparatus for monitoring machine performance

    DOE Patents [OSTI]

    Smith, Stephen F.; Castleberry, Kimberly N.

    1996-01-01

    Machine operating conditions can be monitored by analyzing, in either the time or frequency domain, the spectral components of the motor current. Changes in the electric background noise, induced by mechanical variations in the machine, are correlated to changes in the operating parameters of the machine.

  13. Debugging Fortran on a shared memory machine

    SciTech Connect (OSTI)

    Allen, T.R.; Padua, D.A.

    1987-01-01

    Debugging on a parallel processor is more difficult than debugging on a serial machine because errors in a parallel program may introduce nondeterminism. The approach to parallel debugging presented here attempts to reduce the problem of debugging on a parallel machine to that of debugging on a serial machine by automatically detecting nondeterminism. 20 refs., 6 figs.

  14. Food Service Buildings

    U.S. Energy Information Administration (EIA) Indexed Site

    was a food service building were only asked whether the building was a restaurant, bar, fast food chain, or cafeteria (all the same category) or some other type of food service...

  15. High-speed micro-electro-discharge machining.

    SciTech Connect (OSTI)

    Chandrasekar, Srinivasan Dr. (.School of Industrial Engineering, West Lafayette, IN); Moylan, Shawn P. (School of Industrial Engineering, West Lafayette, IN); Benavides, Gilbert Lawrence

    2005-09-01

    When two electrodes are in close proximity in a dielectric liquid, application of a voltage pulse can produce a spark discharge between them, resulting in a small amount of material removal from both electrodes. Pulsed application of the voltage at discharge energies in the range of micro-Joules results in the continuous material removal process known as micro-electro-discharge machining (micro-EDM). Spark erosion by micro-EDM provides significant opportunities for producing small features and micro-components such as nozzle holes, slots, shafts and gears in virtually any conductive material. If the speed and precision of micro-EDM processes can be significantly enhanced, then they have the potential to be used for a wide variety of micro-machining applications including fabrication of microelectromechanical system (MEMS) components. Toward this end, a better understanding of the impacts the various machining parameters have on material removal has been established through a single discharge study of micro-EDM and a parametric study of small hole making by micro-EDM. The main avenues for improving the speed and efficiency of the micro-EDM process are in the areas of more controlled pulse generation in the power supply and more controlled positioning of the tool electrode during the machining process. Further investigation of the micro-EDM process in three dimensions leads to important design rules, specifically the smallest feature size attainable by the process.

  16. Micro-machined calorimetric biosensors

    DOE Patents [OSTI]

    Doktycz, Mitchel J.; Britton, Jr., Charles L.; Smith, Stephen F.; Oden, Patrick I.; Bryan, William L.; Moore, James A.; Thundat, Thomas G.; Warmack, Robert J.

    2002-01-01

    A method and apparatus are provided for detecting and monitoring micro-volumetric enthalpic changes caused by molecular reactions. Micro-machining techniques are used to create very small thermally isolated masses incorporating temperature-sensitive circuitry. The thermally isolated masses are provided with a molecular layer or coating, and the temperature-sensitive circuitry provides an indication when the molecules of the coating are involved in an enthalpic reaction. The thermally isolated masses may be provided singly or in arrays and, in the latter case, the molecular coatings may differ to provide qualitative and/or quantitative assays of a substance.

  17. Hypervelocity cutting machine and method

    DOE Patents [OSTI]

    Powell, James R.; Reich, Morris

    1996-11-12

    A method and machine 14 are provided for cutting a workpiece 12 such as concrete. A gun barrel 16 is provided for repetitively loading projectiles 22 therein and is supplied with a pressurized propellant from a storage tank 28. A thermal storage tank 32,32A is disposed between the propellant storage tank 28 and the gun barrel 16 for repetitively receiving and heating propellant charges which are released in the gun barrel 16 for repetitively firing projectiles 22 therefrom toward the workpiece 12. In a preferred embodiment, hypervelocity of the projectiles 22 is obtained for cutting the concrete workpiece 12 by fracturing thereof.

  18. Free-piston cutting machine

    DOE Patents [OSTI]

    Ciccarelli, Gaby; Subudhi, Manomohan; Hall, Robert E.

    2000-01-01

    A cutting machine includes a gun barrel for receiving a projectile. A compression tube is disposed in flow communication with the barrel and includes a piston therein. A reservoir is disposed in flow communication with the tube and receives a first gas under pressure. A second gas fills the compression tube on a front face of the piston. And, the pressurized first gas is discharged into the tube on a back face of the piston to accelerate the piston through the tube for compressing the second gas, and in turn launching the projectile through the barrel to impact a workpiece.

  19. Hypervelocity cutting machine and method

    DOE Patents [OSTI]

    Powell, J.R.; Reich, M.

    1996-11-12

    A method and machine are provided for cutting a workpiece such as concrete. A gun barrel is provided for repetitively loading projectiles therein and is supplied with a pressurized propellant from a storage tank. A thermal storage tank is disposed between the propellant storage tank and the gun barrel for repetitively receiving and heating propellant charges which are released in the gun barrel for repetitively firing projectiles therefrom toward the workpiece. In a preferred embodiment, hypervelocity of the projectiles is obtained for cutting the concrete workpiece by fracturing thereof. 10 figs.

  20. Setup reduction approaches for machining

    SciTech Connect (OSTI)

    Gillespie, L.K.

    1997-04-01

    Rapid setup is a common improvement approach in press working operations such as blanking and shearing. It has paid major dividends in the sheet metal industry. It also has been a major improvement thrust for high-production machining operations. However, the literature does not well cover all the setup operations and constraints for job shop work. This review provides some insight into the issues involved. It highlights the floor problems and provides insights for further improvement. The report is designed to provide a quick understanding of the issues.

  1. Chip breaking system for automated machine tool

    DOE Patents [OSTI]

    Arehart, Theodore A.; Carey, Donald O.

    1987-01-01

    The invention is a rotary selectively directional valve assembly for use in an automated turret lathe for directing a stream of high pressure liquid machining coolant to the interface of a machine tool and workpiece for breaking up ribbon-shaped chips during the formation thereof so as to inhibit scratching or other marring of the machined surfaces by these ribbon-shaped chips. The valve assembly is provided by a manifold arrangement having a plurality of circumferentially spaced apart ports each coupled to a machine tool. The manifold is rotatable with the turret when the turret is positioned for alignment of a machine tool in a machining relationship with the workpiece. The manifold is connected to a non-rotational header having a single passageway therethrough which conveys the high pressure coolant to only the port in the manifold which is in registry with the tool disposed in a working relationship with the workpiece. To position the machine tools the turret is rotated and one of the tools is placed in a material-removing relationship of the workpiece. The passageway in the header and one of the ports in the manifold arrangement are then automatically aligned to supply the machining coolant to the machine tool workpiece interface for breaking up of the chips as well as cooling the tool and workpiece during the machining operation.

  2. On-machine sensors to measure paper mechanical properties, Report No. 1

    SciTech Connect (OSTI)

    Hall, M.S.; Habeger, C.C. Jr.

    1988-10-01

    This project is a four-year program which began October 1, 1986. The work may be separated into two distinct parts and four phases. Part I (Phases 1 and 2) is being emphasized to date, and Part II (Phases 3 and 4) will be initiated upon successful completion of Part I. Part I of this project is specifically concerned with the development of a sensor to make on-machine measurements of elastic stiffness in the thickness direction of the paper and the integration of this sensor with an appropriate in-plane sensor. Upon completion of Part I (Phases 1 and 2), we expect to be able to independently monitor the effects of refining, jet-to-wire speed ratios, and draws (and the related drying restraints) on paper properties. This means that we should be able to control these three machine variables continuously and independently during the manufacturing process. Part II of the project will then be concerned with the development of algorithms, hardware, and software necessary to control these variables on the paper machine in the machine direction (Phase 3) and the cross-machine direction (Phase 4). Project objectives call for a successful demonstration of the sensor and control scheme on a laboratory scale paper machine. Success would lead to further work on a pilot scale and eventual scale-up to a full size paper machine. 22 refs., 19 figs., 5 tabs.

  3. Beverage Vending Machines | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Beverage Vending Machines Beverage Vending Machines The Department of Energy (DOE) develops standardized data templates for reporting the results of tests conducted in accordance with current DOE test procedures. Templates may be used by third-party laboratories under contract with DOE that conduct testing in support of ENERGY STAR® verification, DOE rulemakings, and enforcement of the federal energy conservation standards. File Beverage Vending Machines -- v2.0 More Documents &

  4. Methods, systems and apparatus for optimization of third harmonic current injection in a multi-phase machine

    DOE Patents [OSTI]

    Gallegos-Lopez, Gabriel

    2012-10-02

    Methods, system and apparatus are provided for increasing voltage utilization in a five-phase vector controlled machine drive system that employs third harmonic current injection to increase torque and power output by a five-phase machine. To do so, a fundamental current angle of a fundamental current vector is optimized for each particular torque-speed of operating point of the five-phase machine.

  5. Human Reliability Analysis for Digital Human-Machine Interfaces

    SciTech Connect (OSTI)

    Ronald L. Boring

    2014-06-01

    This paper addresses the fact that existing human reliability analysis (HRA) methods do not provide guidance on digital human-machine interfaces (HMIs). Digital HMIs are becoming ubiquitous in nuclear power operations, whether through control room modernization or new-build control rooms. Legacy analog technologies like instrumentation and control (I&C) systems are costly to support, and vendors no longer develop or support analog technology, which is considered technologically obsolete. Yet, despite the inevitability of digital HMI, no current HRA method provides guidance on how to treat human reliability considerations for digital technologies.

  6. Electron beam machining using rotating and shaped beam power distribution

    DOE Patents [OSTI]

    Elmer, John W.; O'Brien, Dennis W.

    1996-01-01

    An apparatus and method for electron beam (EB) machining (drilling, cutting and welding) that uses conventional EB guns, power supplies, and welding machine technology without the need for fast bias pulsing technology. The invention involves a magnetic lensing (EB optics) system and electronic controls to: 1) concurrently bend, focus, shape, scan, and rotate the beam to protect the EB gun and to create a desired effective power-density distribution, and 2) rotate or scan this shaped beam in a controlled way. The shaped beam power-density distribution can be measured using a tomographic imaging system. For example, the EB apparatus of this invention has the ability to drill holes in metal having a diameter up to 1000 .mu.m (1 mm or larger), compared to the 250 .mu.m diameter of laser drilling.

  7. Electron beam machining using rotating and shaped beam power distribution

    DOE Patents [OSTI]

    Elmer, J.W.; O`Brien, D.W.

    1996-07-09

    An apparatus and method are disclosed for electron beam (EB) machining (drilling, cutting and welding) that uses conventional EB guns, power supplies, and welding machine technology without the need for fast bias pulsing technology. The invention involves a magnetic lensing (EB optics) system and electronic controls to: (1) concurrently bend, focus, shape, scan, and rotate the beam to protect the EB gun and to create a desired effective power-density distribution, and (2) rotate or scan this shaped beam in a controlled way. The shaped beam power-density distribution can be measured using a tomographic imaging system. For example, the EB apparatus of this invention has the ability to drill holes in metal having a diameter up to 1,000 {micro}m (1 mm or larger), compared to the 250 {micro}m diameter of laser drilling. 5 figs.

  8. DOE - Office of Legacy Management -- Transcontinental Machine...

    Office of Legacy Management (LM)

    Year: 1990 US.06-1 Site Operations: Metal Fabrication operations - Machined Uranium slugs in support of Savannah River program for evaluation of Uranium fabrication methods. ...

  9. FormCampusMachineShopsLabs.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Highway Baton Rouge, Louisiana 70806 225-578-8887 225-578-6954 (Fax) Form for Campus Machine Shops and Labs Purchaser's Name Phone ...

  10. High pressure water jet mining machine

    DOE Patents [OSTI]

    Barker, Clark R.

    1981-05-05

    A high pressure water jet mining machine for the longwall mining of coal is described. The machine is generally in the shape of a plowshare and is advanced in the direction in which the coal is cut. The machine has mounted thereon a plurality of nozzle modules each containing a high pressure water jet nozzle disposed to oscillate in a particular plane. The nozzle modules are oriented to cut in vertical and horizontal planes on the leading edge of the machine and the coal so cut is cleaved off by the wedge-shaped body.

  11. Evaluation Of Electrochemical Machining Technology For Surface...

    Office of Scientific and Technical Information (OSTI)

    Technology For Surface Improvements In Additive Manufactured Components Citation Details In-Document Search Title: Evaluation Of Electrochemical Machining Technology For ...

  12. Akrong Machine Services | Open Energy Information

    Open Energy Info (EERE)

    Address: 17 w. Rosewood Ave Place: Akron, Ohio Zip: 44301 Sector: Carbon Product: Manufacturing Phone Number: 330-724-1802 Website: akronmachining.com References: Akron Machine...

  13. Diagnostics - Rotating Wall Machine - UW Plasma Physics

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    all diagnostics and feedthroughs must ultimately enter from either end of the machine. ... All signals are integrated prior to digitization by Sterling Scientific analog ...

  14. Machine vision method and apparatus

    SciTech Connect (OSTI)

    Iadipaolo, R.M.; Tkaczyk, R.J.

    1987-07-07

    A machine vision apparatus is described for acquiring the image of a moving object comprising: means for moving the object along a predetermined path; a first linear sensor arranged to track the progress of the object along the path and for generating signals representing objects positions; a second linear sensor arranged to sense portions of the object in a plane transverse of the path for generating streams of data representing line images in the plane; and synchronizing means coupled to the sensors and responsive to the signals for outputting streams of data from the second sensor at predetermined object positions whereby as the object advances through the plane the second sensor obtains many lines images which cumulatively represent an image of the object.

  15. Mining machine having vibration sensor

    SciTech Connect (OSTI)

    Peterson, C.R.

    1987-04-07

    This patent describes a mining machine having means for sensing property variations of the materials associated with a seam of a mine comprising: a cutting tool including a member rotatable about an axis, at least one cutter carried by the rotatable member at a point spaced from the axis for cutting material from the seam, a conductor rod carried by the rotatable member and held in releasable engagement with the cutter, the rod extending to the axis of the rotatable member to conduct to the axis, strain waves which are induced by variations in cutter vibration as the cutter encounters property variations of the materials associated with the seam, and a transducer located at the axis of the rotatable member in communication with the conductor rod to convert the strain waves in the rod to electric signals.

  16. DOE Funds Demonstration of "Ultrasonic Machining"

    Broader source: Energy.gov [DOE]

    Approximately 50 people attended a demonstration of a technology called "ultrasonic machining" at AREVA's Technical Training Center on June 9, 2011. The technology, originally developed by the Edison Welding Institute (EWI), applies ultrasonic acoustic vibrations to traditional machining processes to reduce friction and improve performance.

  17. Design and fabrication of a unique electromechanical machine for long-term fatigue testing

    SciTech Connect (OSTI)

    Boling, K.W.

    1984-12-01

    An electromechanical machine has been designed and fabricated for performing long-term fatigue tests under conditions that simulate those in modern plants. The machine is now commercially available. Its advantages over current electrohydraulic machines are lower initial cost, minimum maintenance requirements, and greater reliability especially when performing long tests. The machine operates in closed-loop fashion by utilizing continuous feedback signals from the specimen extensometer or load cell, it is programmable for testing in strain or load control. The maximum ram rate is 0.056 mm/s (0.134 in./min), maximum ram travel is 102 mm (4 in.) and load capacity is +-44 (+-10 kips). Induction heating controls speciment temperatures to 1000/sup 0/C.

  18. Carbon Emissions: Food Industry

    U.S. Energy Information Administration (EIA) Indexed Site

    Food Industry Carbon Emissions in the Food Industry The Industry at a Glance, 1994 (SIC Code: 20) Total Energy-Related Emissions: 24.4 million metric tons of carbon (MMTC) -- Pct....

  19. Hybrid-secondary uncluttered permanent magnet machine and method

    DOE Patents [OSTI]

    Hsu, John S.

    2005-12-20

    An electric machine (40) has a stator (43), a permanent magnet rotor (38) with permanent magnets (39) and a magnetic coupling uncluttered rotor (46) for inducing a slip energy current in secondary coils (47). A dc flux can be produced in the uncluttered rotor when the secondary coils are fed with dc currents. The magnetic coupling uncluttered rotor (46) has magnetic brushes (A, B, C, D) which couple flux in through the rotor (46) to the secondary coils (47c, 47d) without inducing a current in the rotor (46) and without coupling a stator rotational energy component to the secondary coils (47c, 47d). The machine can be operated as a motor or a generator in multi-phase or single-phase embodiments and is applicable to the hybrid electric vehicle. A method of providing a slip energy controller is also disclosed.

  20. Simplified Hybrid-Secondary Uncluttered Machine And Method

    DOE Patents [OSTI]

    Hsu, John S [Oak Ridge, TN

    2005-05-10

    An electric machine (40, 40') has a stator (43) and a rotor (46) and a primary air gap (48) has secondary coils (47c, 47d) separated from the rotor (46) by a secondary air gap (49) so as to induce a slip current in the secondary coils (47c, 47d). The rotor (46, 76) has magnetic brushes (A, B, C, D) or wires (80) which couple flux in through the rotor (46) to the secondary coils (47c, 47d) without inducing a current in the rotor (46) and without coupling a stator rotational energy component to the secondary coils (47c, 47d). The machine can be operated as a motor or a generator in multi-phase or single-phase embodiments. A method of providing a slip energy controller is also disclosed.

  1. Machinability study of Aermet 100

    SciTech Connect (OSTI)

    Squire, D.V.; Syn, C.K.; Fix, B.L.

    1995-02-08

    Machinability of Aermet 100, an ultrahigh strength alloy developed for Navy by Carpenter Technology as a candidate material for aircraft landing gear application, was studied by performing single-point turning tests. Coated and uncoated carbides, ceramic, and cermet cutting tool inserts of a square geometry (SNG 432 type) were used. Round stock workpieces were tested in the as - received, unaged condition and without using any cutting fluid. The turning tests for each tool material were conducted by (i) first establishing the cutting conditions that would allow the continued generation of broken chips during a given cutting test, (ii) measuring intermittently the flank wear as a function of cutting time under such established cutting conditions for discontinuous broken chips, and (iii) determining the tool life using the criteria specified in the ISO Standard 3685: 1993(E). Cutting tools except some uncoated carbide and ceramic were used with a mechanical chip breaker to induce chip breakage and avoid the generation of long continuous chips. The results obtained include the optimal cutting conditions for discontinuous chips, tool wear - cutting time curves, and records of tool life and tool failure mode for each tool material. From the measured tool life and cutting conditions, the amount of material removed by each cutting material was calculated. Coated carbide with CVD tri-phase coating showed the longest tool life that exceeded the twelve minute criterion and removed the highest amount of material per tool. Other tools failed by cutting edge chipping and their lives were shorter.

  2. Welding Behavior of Free Machining Stainless Steel

    SciTech Connect (OSTI)

    BROOKS,JOHN A.; ROBINO,CHARLES V.; HEADLEY,THOMAS J.; MICHAEL,JOSEPH R.

    2000-07-24

    The weld solidification and cracking behavior of sulfur bearing free machining austenitic stainless steel was investigated for both gas-tungsten arc (GTA) and pulsed laser beam weld processes. The GTA weld solidification was consistent with those predicted with existing solidification diagrams and the cracking response was controlled primarily by solidification mode. The solidification behavior of the pulsed laser welds was complex, and often contained regions of primary ferrite and primary austenite solidification, although in all cases the welds were found to be completely austenite at room temperature. Electron backscattered diffraction (EBSD) pattern analysis indicated that the nature of the base metal at the time of solidification plays a primary role in initial solidification. The solid state transformation of austenite to ferrite at the fusion zone boundary, and ferrite to austenite on cooling may both be massive in nature. A range of alloy compositions that exhibited good resistance to solidification cracking and was compatible with both welding processes was identified. The compositional range is bounded by laser weldability at lower Cr{sub eq}/Ni{sub eq} ratios and by the GTA weldability at higher ratios. It was found with both processes that the limiting ratios were somewhat dependent upon sulfur content.

  3. Food and Beverage Sector (NAICS 311 and 312) Combustion Emissions...

    Office of Environmental Management (EM)

    Within the plant boundary, food and beverage companies have control over facility energy consumption. Outside the plant boundary, where energy is generated by or provided by ...

  4. A waterjet mining machine for use in room and pillar mining operations

    SciTech Connect (OSTI)

    Summers, D.A.

    1990-06-01

    A new mining machine is constructed for use in room and pillar mining operations. This machine uses the action of computer controlled, centrally located high pressure cutting lances to cut deep slots in a coal face. These slots stress relieve the coal ahead of the machine and outline blocks of coal. The movement forward of the machine then wedges up the lower block of coal. This wedging action is assisted by the gathering arms of the loader section of the machine, and by underlying oscillating waterjets which create a slot ahead of the loading wedge as it advances. Finally the top section of coal is brought down by the sequential advance of wedge faced roof support members, again assisted by the waterjet action from the central cutting arms. The machine is designed to overcome major disadvantages of existing room and pillar mining machines in regard to a reduction in respirable dust, the creation of an immediate roof support, and an increase in product size, with concomitant reduction in cleaning costs.

  5. Electric machine for hybrid motor vehicle

    DOE Patents [OSTI]

    Hsu, John Sheungchun

    2007-09-18

    A power system for a motor vehicle having an internal combustion engine and an electric machine is disclosed. The electric machine has a stator, a permanent magnet rotor, an uncluttered rotor spaced from the permanent magnet rotor, and at least one secondary core assembly. The power system also has a gearing arrangement for coupling the internal combustion engine to wheels on the vehicle thereby providing a means for the electric machine to both power assist and brake in relation to the output of the internal combustion engine.

  6. Z Machine | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    Z Machine Air-gas breakdown when Z Machine at Sandia National Laboratories fires. The Z Machine is a pulsed power driver that delivers enormous power in a short duration pulse to a small complex target at the center of the large (34 meters in diameter) accelerator. Pulsed power technology is used to store 20 megajoules of electrical energy over a period of minutes and then to release that energy in a short duration (100- to 300-nanosecond) immense power burst. Z's experimental strength is its

  7. Other: Nanoscale Machines: These Squeaky Wheels Will Get No Grease...

    Office of Scientific and Technical Information (OSTI)

    Nanoscale Machines: These Squeaky Wheels Will Get No Grease Citation Details Title: Nanoscale Machines: These Squeaky Wheels Will Get No Grease...

  8. El Ma Electronic Machining srl | Open Energy Information

    Open Energy Info (EERE)

    Ma Electronic Machining srl Jump to: navigation, search Name: El.Ma. Electronic Machining srl Place: Riva del Garda (TN), Italy Zip: 38066 Sector: Hydro, Hydrogen, Solar, Wind...

  9. DOE - Office of Legacy Management -- American Machine and Foundry...

    Office of Legacy Management (LM)

    to American Machine and Foundry Co - Bus Terminal NY.59-1 - OTS Note; Mitchell to Williams (DOE); Subject: Elimination Recommendation for American Machine & Foundry in N YC;...

  10. DOE - Office of Legacy Management -- Etna Machine Co - OH 28

    Office of Legacy Management (LM)

    Etna Machine Co - OH 28 FUSRAP Considered Sites Site: Etna Machine Co. (OH.28 ) Eliminated from further consideration under FUSRAP Designated Name: Not Designated Alternate Name:...

  11. Mid States Tool and Machine Inc | Open Energy Information

    Open Energy Info (EERE)

    Tool and Machine Inc Jump to: navigation, search Name: Mid States Tool and Machine Inc Place: decatur, Indiana Zip: 46733 Sector: Services Product: Provides engineering and...

  12. Jiangsu Yawei Machine Tool Co | Open Energy Information

    Open Energy Info (EERE)

    Yawei Machine Tool Co Jump to: navigation, search Name: Jiangsu Yawei Machine Tool Co Place: Jiangsu Province, China Product: Chinese sheet matal fabrication industry manufacturer....

  13. Power Electronics and Electric Machines Merit Review, May 2005...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Electric Machines Merit Review, May 2005 Power Electronics and Electric Machines Merit ... PDF icon Annual Review Report More Documents & Publications Power Electronics and ...

  14. KCP relocates 18-ton machine | National Nuclear Security Administratio...

    National Nuclear Security Administration (NNSA)

    relocations. It took nearly three days to disassemble the machine and prepare it for transport. The machine was partially disassembled, removing auxiliary pieces from the main...

  15. Advnaced Power Electronics and Electric Machines (APEEM) R&D...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Advnaced Power Electronics and Electric Machines (APEEM) R&D Program Overview Advnaced Power Electronics and Electric Machines (APEEM) R&D Program Overview 2010 DOE Vehicle ...

  16. International Business Machines Corp IBM | Open Energy Information

    Open Energy Info (EERE)

    Business Machines Corp IBM Jump to: navigation, search Name: International Business Machines Corp (IBM) Place: Armonk, New York Zip: 10504 Sector: Services Product: IBM is a...

  17. Sandia National Laboratories: Contact Z-Machine

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    About Z Z Research Z News Contact Us Facebook Twitter YouTube Flickr RSS Z-Machine Contact Z For more information, please contact us. * Items are Required First Name * Last Name *...

  18. CRAD, Machine Shop Safe Operations Assessment Plan

    Broader source: Energy.gov [DOE]

    The purpose of this assessment is to verify that machine shop operators are provided a safe and healthful workplace which will reduce or prevent injuries, illnesses, and accidental losses.

  19. Seattle City Light- Vending Machine Rebate Program

    Broader source: Energy.gov [DOE]

    Seattle City Light offers qualifying customers $80 rebates for the purchase of VendingMiser Energy Efficient Vending Machines. VendingMiser reduces the energy consumption of cold drink vending...

  20. Method of fabricating a micro machine

    SciTech Connect (OSTI)

    Stalford, Harold L

    2014-11-11

    A micro machine may be in or less than the micrometer domain. The micro machine may include a micro actuator and a micro shaft coupled to the micro actuator. The micro shaft is operable to be driven by the micro actuator. A tool is coupled to the micro shaft and is operable to perform work in response to at least motion of the micro shaft.

  1. Production and Machining of Thin Wall Gray and Ductile Cast Iron

    SciTech Connect (OSTI)

    Fleischman, E.H.; Li, H.; Griffin, R.; Bates, C.E.; Eleftheriou, E.

    2000-11-03

    The University of Alabama at Birmingham, in cooperation with the American Foundry Society, companies across North America, with support from the U.S. Department of Energy, is conducting a project to develop an understanding of the factors that control the machinability of cast gray and ductile iron. Differences of as much as 500% have been found in machinability have been observed at the same strength. The most machinable irons were those with a high cell counts and few carbonitride inclusions. Additions of tin and copper can be added to both gray and ductile iron to stabilize the pearlite, but excessive additions (above those required to produce the desired pearlite content) degrade the machinability.

  2. Survey of ceramic machining in Japan

    SciTech Connect (OSTI)

    Bandyopadhyay, B.P.; Blau, P.J.

    1993-07-01

    This report is a compilation of four subcontract reports provided by B. P. Bandyopadhyay who, while a visiting professor at Toyohashi University in Japan, conducted a survey of ceramic machining technology in that country from January 1 through December 31, 1992. Various aspects of machining technology were surveyed: types of parts being produced, types of ceramic materials being used, the nature of current ceramic machining research and development, and types of machine tools. The four separate reports compiled here were originally provided in a narrative, chronological form, and some of the information has been reorganized into topical areas for this compilation. This report is organized into three sections: The first describes ten ceramic machining research and development organizations and provides a reference list of their current technical publications; the second, two major trade shows; and the third, several other products and commercial developments noted during the course of Bandyopadhyay`s stay in Japan. An Appendix lists key individuals who are currently conducting ceramic machining research in Japan.

  3. Simplified theory of Ringbom Stirling machines

    SciTech Connect (OSTI)

    Rochelle, P.; Stouffs, P.

    1998-07-01

    This paper presents a first order analysis of four types of overdriven free-displacer Stirling machines. All the presented types of machines can work as refrigerating machines, prime movers or heat exchange accelerators depending on parameters such as the hot to cold source temperatures ratio, the dimensional mass of working gas in the machine, the displacer rod to displacer cross sectional area ratio, the corrected dead space to piston cylinder volume ratio and the displacer to piston cylinder volume ratio. In its analytical form this theory holds for machines at low speed as it is assumed that the piston displacement can be neglected during the displacer movement duration. This analysis may be used to find the conditions and values giving either the best theoretical refrigerating cycle or the best theoretical prime mover cycle, the associated reference work, reference time, efficiency and heat quantities involved. A table gives the analytical expressions and the limiting values of the main parameters for the four different types of Ringbom machines considered. The preliminary design of a Ringbom prime mover is then presented. The main parameters influences are predicted and the magnitude of work, rotational speed limit and efficiency are obtained.

  4. Machine-z: Rapid machine-learned redshift indicator for Swift gamma-ray

    Office of Scientific and Technical Information (OSTI)

    bursts (Journal Article) | DOE PAGES Machine-z: Rapid machine-learned redshift indicator for Swift gamma-ray bursts This content will become publicly available on March 8, 2017 Title: Machine-z: Rapid machine-learned redshift indicator for Swift gamma-ray bursts Studies of high-redshift gamma-ray bursts (GRBs) provide important information about the early Universe such as the rates of stellar collapsars and mergers, the metallicity content, constraints on the re-ionization period, and probes

  5. Machine-z: Rapid machine-learned redshift indicator for Swift...

    Office of Scientific and Technical Information (OSTI)

    458; Journal Issue: 4; Journal ID: ISSN 0035-8711 ... Country of Publication: United States Language: English Subject: 79 ASTRONOMY AND ASTROPHYSICS GRB; machine learning; ...

  6. Machine-z: Rapid machine-learned redshift indicator for Swift gamma-ray

    Office of Scientific and Technical Information (OSTI)

    bursts (Journal Article) | SciTech Connect Journal Article: Machine-z: Rapid machine-learned redshift indicator for Swift gamma-ray bursts Citation Details In-Document Search This content will become publicly available on March 8, 2017 Title: Machine-z: Rapid machine-learned redshift indicator for Swift gamma-ray bursts Studies of high-redshift gamma-ray bursts (GRBs) provide important information about the early Universe such as the rates of stellar collapsars and mergers, the metallicity

  7. Pet Food Safety A Shared Concern

    SciTech Connect (OSTI)

    Buchanan, Robert L; Baker, Robert C; Charlton, Adrian J; Riviere, Jim E; Standaert, Robert F

    2011-01-01

    The safety of the food supply is a subject of intense interest to consumers, particularly as a result of large scale outbreaks that involve hundreds and sometimes thousands of consumers. During the last decade this concern about food safety has expanded to include the diets of companion animals as a result of several incidences of chemical toxicities and infectious disease transmission. This has led to increased research into the causes and controls for these hazards for both companion animals and their owners. The following summary provides an introduction to the issues, challenges, and new tools being developed to ensure that commercial pet foods are both nutritious and safe.

  8. Temporary Food Service

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Food Service The SLAC Café, auditorium and visitor center have been closed and will be replaced with a new Science and User Support Building (SUSB). During this construction (2013-2015), temporary food service will be provided by the Cardinal Chef Mobile Gourmet food trucks. On-Site The food trucks are located in front of Building 27. Hours of Operation Monday through Friday Breakfast: 7:30AM-9:30AM Lunch: 11:00AM-2:00PM Menu: http://www-project.slac.stanford.edu/foodtruckmenu/default.asp Local

  9. Holiday Food Drive

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Community Programs Office (505) 665-4400 Email Get Expertise Helping feed Northern New Mexico families During the Laboratory's 2015 Annual Food Drive, employees and subcontract...

  10. briquetting machine plant India | OpenEI Community

    Open Energy Info (EERE)

    briquetting machine plant India Home There are currently no posts in this category. Syndicate content...

  11. Machine plumbness criteria: Interim technology release

    SciTech Connect (OSTI)

    Not Available

    1987-06-01

    The objective of this technology release is to define the maximum allowable deviation from plumb of the centrifuge machine and to recommend machine installation techniques to achieve the specified criteria. The centrifuge feature used as a reference for plumbness is the casing centerline as defined by a line drawn between the theoretical centers of the top and bottom flange faces. In practice, this measurement is accomplished by using specified casing flange diameters or bolt patterns as the reference points. The criterion adopted for GCEP is that each machine shall be plumb within 0.5 in. over the length of the casing as initially installed. Over a long period of time the plumbness is allowed to degrade to 1.0 in. This standard should be achievable using the currently planned installation techniques and within a time limit consistent with GCEP operational objectives. For development testing, centrifuge machines are meticulously adjusted using a plumb bob to achieve a plumbness with 1/8 in. About one to two days are required to complete the installation. This level of effort is justified for a development machine especially where baseline data is being gathered. A more reasonable standard with a corresponding reduction in installation time is required for GCEP. The specified criteria of 0.5 in. maximum out-of-plumb at time of installation and 1.0 in., ultimate, are believed to be a reasonable compromise. Machine design features or operating modes that are dependent on vertical alignment were examined to assess the impact of the selected plumbness criteria. Machine performance and design requirements are defined in the applicable technology release documents.

  12. Machine protection system for rotating equipment and method

    DOE Patents [OSTI]

    Lakshminarasimha, Arkalgud N. (Marietta, GA); Rucigay, Richard J. (Marietta, GA); Ozgur, Dincer (Kennesaw, GA)

    2003-01-01

    A machine protection system and method for rotating equipment introduces new alarming features and makes use of full proximity probe sensor information, including amplitude and phase. Baseline vibration amplitude and phase data is estimated and tracked according to operating modes of the rotating equipment. Baseline vibration and phase data can be determined using a rolling average and variance and stored in a unit circle or tracked using short term average and long term average baselines. The sensed vibration amplitude and phase is compared with the baseline vibration amplitude and phase data. Operation of the rotating equipment can be controlled based on the vibration amplitude and phase.

  13. Guest Editorial: Electric Machines in Renewable Energy Applications

    SciTech Connect (OSTI)

    Aliprantis, Dionysios; El-Sharkawi, Mohamed; Muljadi, Eduard; Brown, Ian; Chiba, Akira; Dorrell, David; Erlich, Istvan; Kerszenbaum, Isidor; Levi, Emil; Mayor, Kevin; Mohammed, Osama; Papathanassiou, Stavros; Popescu, Mircea; Qiao, Wei; Wu, Dezheng

    2015-12-01

    The main objective of this special issue is to collect and disseminate publications that highlight recent advances and breakthroughs in the area of renewable energy resources. The use of these resources for production of electricity is increasing rapidly worldwide. As of 2015, a majority of countries have set renewable electricity targets in the 10%-40% range to be achieved by 2020-2030, with a few notable exceptions aiming for 100% generation by renewables. We are experiencing a truly unprecedented transition away from fossil fuels, driven by environmental, energy security, and socio-economic factors.Electric machines can be found in a wide range of renewable energy applications, such as wind turbines, hydropower and hydrokinetic systems, flywheel energy storage devices, and low-power energy harvesting systems. Hence, the design of reliable, efficient, cost-effective, and controllable electric machines is crucial in enabling even higher penetrations of renewable energy systems in the smart grid of the future. In addition, power electronic converter design and control is critical, as they provide essential controllability, flexibility, grid interface, and integration functions.

  14. The effect of nonlinear thermo-fluid-dynamic terms on free-piston Stirling machine stability

    SciTech Connect (OSTI)

    Benvenuto, G.; Monte, F. de

    1996-12-31

    In this work a new linearization technique of the dynamic balance equations of a free-piston Stirling machine is developed. It takes into account the nonlinear thermo-fluid-dynamic terms inherent in the machine, although keeping the linearity of the differential dynamic equations. This allows the equations of motion to be solved still analytically and, therefore, useful algebraic relations (already established by the authors in past studies) linking together the various machine parameters to be used. The advantages related to the proposed linearization methodology are the following: (1) it gives a right interpretation of the machine working when the operational parameters vary, because the considered nonlinear terms have a stabilizing effect; (2) it can be used to predict the machine performance not only with more accuracy, but especially in a more exhaustive way, allowing to estimate also the piston stroke and, therefore, the delivered power; (3) it enables to design the machine in such a way to enhance its stability, thus eliminating the necessity of power control systems.

  15. Automatic feed system for ultrasonic machining

    DOE Patents [OSTI]

    Calkins, Noel C.

    1994-01-01

    Method and apparatus for ultrasonic machining in which feeding of a tool assembly holding a machining tool toward a workpiece is accomplished automatically. In ultrasonic machining, a tool located just above a workpiece and vibrating in a vertical direction imparts vertical movement to particles of abrasive material which then remove material from the workpiece. The tool does not contact the workpiece. Apparatus for moving the tool assembly vertically is provided such that it operates with a relatively small amount of friction. Adjustable counterbalance means is provided which allows the tool to be immobilized in its vertical travel. A downward force, termed overbalance force, is applied to the tool assembly. The overbalance force causes the tool to move toward the workpiece as material is removed from the workpiece.

  16. Micro-machined thermo-conductivity detector

    DOE Patents [OSTI]

    Yu, Conrad

    2003-01-01

    A micro-machined thermal conductivity detector for a portable gas chromatograph. The detector is highly sensitive and has fast response time to enable detection of the small size gas samples in a portable gas chromatograph which are in the order of nanoliters. The high sensitivity and fast response time are achieved through micro-machined devices composed of a nickel wire, for example, on a silicon nitride window formed in a silicon member and about a millimeter square in size. In addition to operating as a thermal conductivity detector, the silicon nitride window with a micro-machined wire therein of the device can be utilized for a fast response heater for PCR applications.

  17. Machine Learning Toolkit for Extreme Scale

    Energy Science and Technology Software Center (OSTI)

    2014-03-31

    Support Vector Machines (SVM) is a popular machine learning technique, which has been applied to a wide range of domains such as science, finance, and social networks for supervised learning. MaTEx undertakes the challenge of designing a scalable parallel SVM training algorithm for large scale systems, which includes commodity multi-core machines, tightly connected supercomputers and cloud computing systems. Several techniques are proposed for improved speed and memory space usage including adaptive and aggressive elimination ofmore » samples for faster convergence , and sparse format representation of data samples. Several heuristics for earliest possible to lazy elimination of non-contributing samples are considered in MaTEx. In many cases, where an early sample elimination might result in a false positive, low overhead mechanisms for reconstruction of key data structures are proposed. The proposed algorithm and heuristics are implemented and evaluated on various publicly available datasets« less

  18. Multi-winding homopolar electric machine

    DOE Patents [OSTI]

    Van Neste, Charles W

    2012-10-16

    A multi-winding homopolar electric machine and method for converting between mechanical energy and electrical energy. The electric machine includes a shaft defining an axis of rotation, first and second magnets, a shielding portion, and a conductor. First and second magnets are coaxial with the shaft and include a charged pole surface and an oppositely charged pole surface, the charged pole surfaces facing one another to form a repulsive field therebetween. The shield portion extends between the magnets to confine at least a portion of the repulsive field to between the first and second magnets. The conductor extends between first and second end contacts and is toroidally coiled about the first and second magnets and the shield portion to develop a voltage across the first and second end contacts in response to rotation of the electric machine about the axis of rotation.

  19. Method for machining steel with diamond tools

    DOE Patents [OSTI]

    Casstevens, John M.

    1986-01-01

    The present invention is directed to a method for machining optical quality inishes and contour accuracies of workpieces of carbon-containing metals such as steel with diamond tooling. The wear rate of the diamond tooling is significantly reduced by saturating the atmosphere at the interface of the workpiece and the diamond tool with a gaseous hydrocarbon during the machining operation. The presence of the gaseous hydrocarbon effectively eliminates the deterioration of the diamond tool by inhibiting or preventing the conversion of the diamond carbon to graphite carbon at the point of contact between the cutting tool and the workpiece.

  20. Method for machining steel with diamond tools

    DOE Patents [OSTI]

    Casstevens, J.M.

    1984-01-01

    The present invention is directed to a method for machine optical quality finishes and contour accuracies of workpieces of carbon-containing metals such as steel with diamond tooling. The wear rate of the diamond tooling is significantly reduced by saturating the atmosphere at the interface of the workpiece and the diamond tool with a gaseous hydrocarbon during the machining operation. The presence of the gaseous hydrocarbon effectively eliminates the deterioration of the diamond tool by inhibiting or preventing the conversion of the diamond carbon to graphite carbon at the point of contact between the cutting tool and the workpiece.

  1. Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Vanderhoff, Alex

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 6/1/13 to 6/30/13

  2. Green Machine Florida Canyon Hourly Data 20130731

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Vanderhoff, Alex

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 7/1/13 to 7/31/13.

  3. 20130416_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Vanderhoff, Alex

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 4/16/13.

  4. 20140430_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Thibedeau, Joe

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 01 April to 30 April 2014.

  5. Apparatus for cooling an electric machine

    DOE Patents [OSTI]

    Palafox, Pepe; Gerstler, William Dwight; Shen, Xiaochun; El-Refaie, Ayman Mohamed Fawzi; Lokhandwalla, Murtuza; Salasoo, Lembit

    2013-07-16

    Provided is an apparatus, for example, for use with a rotating electric machine, that includes a housing. The housing can include a housing main portion and a housing end portion. The housing main portion can be configured to be disposed proximal to a body portion of a stator section of an electric machine. The housing main portion can define a main fluid channel that is configured to conduct fluid therethrough. The housing end portion can receive fluid from said main fluid channel and direct fluid into contact with a winding end portion of a conductive winding of the stator section.

  6. High slot utilization systems for electric machines

    DOE Patents [OSTI]

    Hsu, John S

    2009-06-23

    Two new High Slot Utilization (HSU) Systems for electric machines enable the use of form wound coils that have the highest fill factor and the best use of magnetic materials. The epoxy/resin/curing treatment ensures the mechanical strength of the assembly of teeth, core, and coils. In addition, the first HSU system allows the coil layers to be moved inside the slots for the assembly purpose. The second system uses the slided-in teeth instead of the plugged-in teeth. The power density of the electric machine that uses either system can reach its highest limit.

  7. Green Machine Florida Canyon Hourly Data 20130731

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Vanderhoff, Alex

    2013-08-30

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 7/1/13 to 7/31/13.

  8. 20140430_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Thibedeau, Joe

    2014-05-05

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 01 April to 30 April 2014.

  9. 20130416_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Vanderhoff, Alex

    2013-04-24

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 4/16/13.

  10. Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Vanderhoff, Alex

    2013-07-15

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 6/1/13 to 6/30/13

  11. Integrated Inverter Control for Multiple Electric Machines - Energy

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Integrated Field Exercise NNSA Administrator Recognizes Los Alamos Employees for Exceptional Work Recognizing the LANL IFE14 team's "extraordinary effort," Administrator Klotz, center, presented team leader Ward Hawkins (second from left) with the NNSA Silver Medal, and team members Richard Kelley, left, and Aviva Sussman, second from right with the NNSA Excellence Medal. Not pictured are Emily Report) | SciTech Connect

    Integrated Genome-Based Studies of Shewanella Ecophysiology

  12. List of Vending Machine Controls Incentives | Open Energy Information

    Open Energy Info (EERE)

    Eligible Technologies Active APS - Energy Efficiency Solutions for Business (Arizona) Utility Rebate Program Arizona Commercial Industrial Institutional Local Government Retail...

  13. Electric machine and current source inverter drive system

    DOE Patents [OSTI]

    Hsu, John S

    2014-06-24

    A drive system includes an electric machine and a current source inverter (CSI). This integration of an electric machine and an inverter uses the machine's field excitation coil for not only flux generation in the machine but also for the CSI inductor. This integration of the two technologies, namely the U machine motor and the CSI, opens a new chapter for the component function integration instead of the traditional integration by simply placing separate machine and inverter components in the same housing. Elimination of the CSI inductor adds to the CSI volumetric reduction of the capacitors and the elimination of PMs for the motor further improve the drive system cost, weight, and volume.

  14. Direct fired absorption machine flue gas recuperator

    DOE Patents [OSTI]

    Reimann, Robert C.; Root, Richard A.

    1985-01-01

    A recuperator which recovers heat from a gas, generally the combustion gas of a direct-fired generator of an absorption machine. The recuperator includes a housing with liquid flowing therethrough, the liquid being in direct contact with the combustion gas for increasing the effectiveness of the heat transfer between the gas and the liquid.

  15. Needle bar for warp knitting machines

    DOE Patents [OSTI]

    Hagel, Adolf; Thumling, Manfred

    1979-01-01

    Needle bar for warp knitting machines with a number of needles individually set into slits of the bar and having shafts cranked to such an extent that the head section of each needle is in alignment with the shaft section accommodated by the slit. Slackening of the needles will thus not influence the needle spacing.

  16. Covered Product Category: Refrigerated Beverage Vending Machines

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance and Federal efficiency requirements across a variety of product categories, including refrigerated beverage vending machines, which are covered by the ENERGY STAR® program. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  17. Transient simulation of absorption machines

    SciTech Connect (OSTI)

    Anand, D.K.; Allen, R.W.; Kumar, B.

    1982-08-01

    This paper presents a model for a water-cooled Lithium-Bromide/water absorption chiller and predicts its transient response both during the start-up phase and during the shutoff period. The simulation model incorporates such influencing factors as the thermodynamic properties of the working fluid, the absorbent, the heat-transfer configuration of different components of the chiller and related physical data. The time constants of different components are controlled by a set of key parameters that have been identified in this study. The results show a variable but at times significant amount of time delay before the chiller capacity gets close to its steady-state value. The model is intended to provide an insight into the mechanism of build-up to steady-state performance. By recognizing the significant factors contributing to transient degradation, steps can be taken to reduce such degradation. The evaluation of the residual capacity in the shut-off period will yield more realistic estimates of chiller COP for a chiller satisfying dynamic space cooling load.

  18. Transient simulation of absorption machines

    SciTech Connect (OSTI)

    Anand, D.K.; Allen, R.W.; Kumar, B.

    1982-08-01

    This paper presents a model for a water-cooled Lithium-Bromide/water absorption chiller and predicts its transient response both during the start-up phase and during the shutoff period. The simulation model incorporates such influencing factors as the thermodynamic properties of the working fluid, the absorbent, the heat-transfer configuration of different components of the chiller and related physical data. The time constants of different components are controlled by a set of key parameters that have been identified in this study. The results show a variable but at times significant amount of time delay before the chiller capacity gets close to its steadystate value. The model is intended to provide an insight into the mechanism of build-up to steady-state performance. By recognizing the significant factors contributing to transient degradation, steps can be taken to reduce such degradation. The evaluation of the residual capacity in the shut-off period will yield more realistic estimates of chiller COP for a chiller satisfying dynamic space cooling load.

  19. MTX (Microwave Tokamak Experiment) facility and machine grounding plan

    SciTech Connect (OSTI)

    Bell, H.H.; Rice, B.W.; Petersen, D.E.; Herrera, C.H.

    1987-10-07

    A key issue in the design of fusion research experiments and their related facilities is the control of ground currents. Because of the large magnetic field, high voltages and high currents present in most of these installations, it is essential to avoid ground loops, and to control ground currents during both normal operations and fault conditions. This paper describes the grounding policy that was developed for MTX. The vault area was divided into zones, and each of the four walls was treated as a separate grounding area. Cable runs and magnet buss bars were run into the machine radially. The paper also describes the steps taken to isolate diagnostic signals and power for pumps and instruments. The paper outlines some of the field calculations used to predict problem areas, and to reveal voltage isolation levels that were required. The paper includes the active ground fault detection system used to insure the integrity of the ground system. 2 refs., 5 figs.

  20. New Accessory for Cleaning the Inside of the Machine Tool Cavity

    SciTech Connect (OSTI)

    Lazarus, Lloyd

    2009-04-21

    The best way to extend the life of a metalworking fluid (MWF) is to make sure the machine tool and MWF delivery system are properly cleaned at least once per year. The dilemma the MWF manager is faced with is: How does one clean the machine tool and the MWF system on a large machine tool with an enclosure in a timely manner without impacting production schedules? Remember the walls and roof of the machine enclosure are coated with a film of dried contaminated MWF that must also be removed. If not removed, the deposits on these surfaces can recontaminate the fresh charge of MWF. I have found a product that with this revised procedure helps to shorten the machine tool down time involved with machine cleaning. (1) Discuss with your MWF supplier if they have a machine cleaning product that can be used with your current water based MWF during normal machining operations. Most MWF manufacturers have a machine cleaner that can be used at a lower concentration (1-2% vs. 5%) and can be used while still making production parts for a short period of time (usually 24-48 hours). (2) Make sure this machine cleaner is compatible with the work-piece material you are machining into product. Most cleaners are compatible with ferrous alloys. Because of the increased alkalinity of the fluid you might experience staining if you are machining copper or aluminum alloys. (3) Remove the chips from the chips pans and fluid channels. (4) During off shift hours circulate the MWF using a new product marketed by Rego-Fix called a 'Hydroball'. This device has a 5/8 inch diameter straight shank which allows it to be installed in any collet or solid quick change tool holder. It has multiple nozzles so that the user can control the spray pattern generated when the MWF is circulated. It allows the user to utilize the high pressure, through spindle MWF delivery capability of your machine tool for cleaning purposes. The high pressure MWF system can now be effectively used for cleaning purposes. This will also work with standard pressure system but you must reduce the number of nozzles utilized. By combining the movement of the machine axis around the operating envelope and the MWF circulation you can do a reasonably effective job of washing the inside of the machine tool operating cavity. Way covers will be moved and surfaces exposed because of axis movement. Spray direction will change to better wash fixtures and machine tool components. Deposits will start to breakdown and be washed into the machine tool sump. Since the cycle will run four or more hours it can be done with a weaker cleaning solution. The distributor states that the unit can be rotated up to 50 RPM. When running it has the same effect as the washing rotor inside of your home dishwasher. Inside the cavity on a machining center there is a lot of splash. During normal operations, MWF deposits buildup on the walls and roof of the enclosures. If these deposits (containing bacteria, mold and other contaminants) are not removed they will inoculate the fresh charge of MWF when they are resaturated. When you clean the inside of machine tool cavity, time is spent removing these deposits on the walls and roof of the enclosure. Getting to these surfaces is very difficult usually requiring that a member of the cleaning crew get inside the machine tool to reach them. The Hydro ball is effective in distributing the cleaning solution on all surfaces of the enclosure under high pressure. The only negative we have found is you get to find all the gaps and leaks in your machine tool enclosure. By running the hydro ball with the machine cleaner enriched MWF during off shift (4-8 hours) you can effectively remove these deposits and buildups on the internal surfaces of the cavity of the machine tool and wash them down into the sump. You also clean the internal components of the MWF system without interrupting normal scheduled work. (5) Pump out the spent MWF. You will have found that most of the deposits have been washed from the internal surfaces of the enclosure. For extremely dirty machines you might have to

  1. Y-12 sets the pace in precision machining - Or: Establishing...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    precision machining (title used by The Oak Ridger) Beginning in the very early years of Y-12's history, precision machining has played a strong and leader- ship role in the...

  2. DOE - Office of Legacy Management -- Landis Machine Tool Co ...

    Office of Legacy Management (LM)

    Also see Documents Related to LANDIS MACHINE TOOL CO. PA.34-1 - DOE Memorandum; A. Williams to the File; Subject: Elimination of the Landis Machine Company site; April 24, 1991...

  3. DOE - Office of Legacy Management -- National Acme Machine Co...

    Office of Legacy Management (LM)

    Acme Machine Co - OH 0-04 FUSRAP Considered Sites Site: NATIONAL ACME MACHINE CO. (OH.0-04 ) Eliminated from further consideration under FUSRAP Designated Name: Not Designated...

  4. Machine Learning for the Grid (Conference) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    Machine Learning for the Grid Citation Details In-Document Search Title: Machine Learning for the Grid You are accessing a document from the Department of Energy's (DOE) SciTech ...

  5. New "Cool Roof Time Machine" Will Accelerate Cool Roof Deployment...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    "Cool Roof Time Machine" Will Accelerate Cool Roof Deployment New "Cool Roof Time Machine" Will Accelerate Cool Roof Deployment April 24, 2015 - 4:21pm Addthis Berkeley Lab...

  6. A high performance inverter-fed drive system of an interior permanent magnet synchronous machine

    SciTech Connect (OSTI)

    Bose, B.K.

    1987-01-01

    A high performance fully operational four-quadrant control scheme of an interior permanent magnet synchronous machine is described. The machine operates smoothly with full performance in constant-torque region as well as in flux-weakening constant-power region in both the directions of motion. The transition between constant-torque region and constant-power region is very smooth at all conditions of operation. The control in constant-torque region is based on vector or field-oriented technique with the direct-axis aligned to the total stator flux, whereas the constant-power region control is implemented by orientation of torque angle of the impressed square-wave voltage through the feedforward vector rotator. The control system is implemented digitally using distributed microcomputer system and all the essential feedback signals, such as torque, flux, etc., are estimated with precision. The control has been described with an outer torque control loop primarily for traction type applications, but speed and position control loops can be easily added to extend its application to other industrial drives. A 70 hp drive system using a Neodymium-Iron-Boron PM machine and transistor PWM inverter has been designed and extensively tested in laboratory on a dynamometer, and performances are found to be excellent.

  7. March 8, 2006: Sandia's Z Machine | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    8, 2006: Sandia's Z Machine March 8, 2006: Sandia's Z Machine March 8, 2006: Sandia's Z Machine March 8, 2006 The Department's Sandia National Laboratories announces that its Z machine has produced plasmas that exceed temperatures of 2 billion degrees Kelvin-hotter than the interiors of stars. The unexpectedly hot output, if its cause were understood and harnessed, could eventually mean that smaller, less costly nuclear fusion plants would produce the same amount of energy as larger plants. The

  8. Covered Product Category: Water-Cooled Ice Machines

    Broader source: Energy.gov [DOE]

    The Federal Energy Management Program (FEMP) provides acquisition guidance and federal efficiency requirements for water-cooled ice machines.

  9. Attend a Webinar on AMO's Next Generation Electric Machines Funding

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Opportunity | Department of Energy a Webinar on AMO's Next Generation Electric Machines Funding Opportunity Attend a Webinar on AMO's Next Generation Electric Machines Funding Opportunity March 24, 2015 - 3:09pm Addthis AMO's Next Generation Electric Machines (NGEM) program recently released the Funding Opportunity Announcement (FOA): Next Generation Electric Machines: Megawatt Class Motors. $20 million will fund four to six projects that develop a new generation of energy efficient, high

  10. Multilevel-Dc-Bus Inverter For Providing Sinusoidal And Pwm Electrical Machine Voltages

    DOE Patents [OSTI]

    Su, Gui-Jia [Knoxville, TN

    2005-11-29

    A circuit for controlling an ac machine comprises a full bridge network of commutation switches which are connected to supply current for a corresponding voltage phase to the stator windings, a plurality of diodes, each in parallel connection to a respective one of the commutation switches, a plurality of dc source connections providing a multi-level dc bus for the full bridge network of commutation switches to produce sinusoidal voltages or PWM signals, and a controller connected for control of said dc source connections and said full bridge network of commutation switches to output substantially sinusoidal voltages to the stator windings. With the invention, the number of semiconductor switches is reduced to m+3 for a multi-level dc bus having m levels. A method of machine control is also disclosed.

  11. Evaluation Of Electrochemical Machining Technology For Surface Improvements

    Office of Scientific and Technical Information (OSTI)

    In Additive Manufactured Components (Technical Report) | SciTech Connect Evaluation Of Electrochemical Machining Technology For Surface Improvements In Additive Manufactured Components Citation Details In-Document Search Title: Evaluation Of Electrochemical Machining Technology For Surface Improvements In Additive Manufactured Components ORNL Manufacturing Demonstration Facility worked with ECM Technologies LLC to investigate the use of precision electro-chemical machining technology to

  12. R&D ERL: Machine Protection System

    SciTech Connect (OSTI)

    Altinbas, Z.

    2010-01-01

    The Machine Protection System (MPS) is a device-safety system that is designed to prevent damage to hardware by generating interlocks, based upon the state of input signals generated by selected sub-system. It exists to protect key machinery such as the 50 kW and 1 MW RF Systems. When a fault state occurs, the MPS is capable of responding with an interlock signal within several microseconds. The Machine Protection System inputs are designed to be fail-safe. In addition, all fault conditions are latched and time-stamped. The ERL MPS is based on a National Instruments hardware platform, and is programmed by utilizing National Instruments development environment for a visual programming language.

  13. Requirements for CEC POP machine protection system

    SciTech Connect (OSTI)

    Pinayev, I.

    2015-02-18

    The requirements of CEC POP machine protection system are meant to prevent damage to a vacuum chamber by a missteered electron beam. In this example, beam energy = 22 MeV, Maximal bunch charge = 5 nC, Maximal repetition rate = 78 kHz, Normalized emittance = 5 mm mrad, Minimal β-function = 1 m. From this information the requirements of the protection system can be calculated by factoring the information into equations to find beam densities and temperature excursions.

  14. Nanostructured Materials by Machining | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Presentation given at the 2007 Diesel Engine-Efficiency & Emissions Research Conference (DEER 2007). 13-16 August, 2007, Detroit, Michigan. Sponsored by the U.S. Department of Energy's (DOE) Office of FreedomCAR and Vehicle Technologies (OFCVT). PDF icon deer07_trumble.pdf More Documents & Publications Ultra-Fine Grain Foils and Sheets by Large-Strain Extrusion Machining 2011 Annual Progress Report for Lightweighting Materials Vehicle Technologies Office: 2010 Lightweight Materials

  15. Abrasive slurry composition for machining boron carbide

    DOE Patents [OSTI]

    Duran, E.L.

    1984-11-29

    An abrasive slurry particularly suited for use in drilling or machining boron carbide consists essentially of a suspension of boron carbide and/or silicon carbide grit in a carrier solution consisting essentially of a dilute solution of alkylaryl polyether alcohol in octyl alcohol. The alkylaryl polyether alcohol functions as a wetting agent which improves the capacity of the octyl alcohol for carrying the grit in suspension, yet without substantially increasing the viscosity of the carrier solution.

  16. Abrasive slurry composition for machining boron carbide

    DOE Patents [OSTI]

    Duran, Edward L.

    1985-01-01

    An abrasive slurry particularly suited for use in drilling or machining boron carbide consists essentially of a suspension of boron carbide and/or silicon carbide grit in a carrier solution consisting essentially of a dilute solution of alkylaryl polyether alcohol in octyl alcohol. The alkylaryl polyether alcohol functions as a wetting agent which improves the capacity of the octyl alcohol for carrying the grit in suspension, yet without substantially increasing the viscosity of the carrier solution.

  17. Dovetail spoke internal permanent magnet machine

    DOE Patents [OSTI]

    Alexander, James Pellegrino; EL-Refaie, Ayman Mohamed Fawzi; Lokhandwalla, Murtuza; Shah, Manoj Ramprasad; VanDam, Jeremy Daniel

    2011-08-23

    An internal permanent magnet (IPM) machine is provided. The IPM machine includes a stator assembly and a stator core. The stator core also includes multiple stator teeth. The stator assembly is further configured with stator windings to generate a stator magnetic field when excited with alternating currents and extends along a longitudinal axis with an inner surface defining a cavity. The IPM machine also includes a rotor assembly and a rotor core. The rotor core is disposed inside the cavity and configured to rotate about the longitudinal axis. The rotor assembly further includes a shaft. The shaft further includes multiple protrusions alternately arranged relative to multiple bottom structures provided on the shaft. The rotor assembly also includes multiple stacks of laminations disposed on the protrusions and dovetailed circumferentially around the shaft. The rotor assembly further includes multiple pair of permanent magnets for generating a magnetic field, which magnetic field interacts with the stator magnetic field to produce a torque. The multiple pair of permanent magnets are disposed between the stacks. The rotor assembly also includes multiple middle wedges mounted between each pair of the multiple permanent magnets.

  18. DOE-HDBK-1122-99; Radiological Control Technician Training

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Course Number: Radiological Control Technicians Module ... Module 2.15 Radiological Considerations for First Aid ... want to remove the machine from the room ASAP. 2) ...

  19. Radioactivity in food crops

    SciTech Connect (OSTI)

    Drury, J.S.; Baldauf, M.F.; Daniel, E.W.; Fore, C.S.; Uziel, M.S.

    1983-05-01

    Published levels of radioactivity in food crops from 21 countries and 4 island chains of Oceania are listed. The tabulation includes more than 3000 examples of 100 different crops. Data are arranged alphabetically by food crop and geographical origin. The sampling date, nuclide measured, mean radioactivity, range of radioactivities, sample basis, number of samples analyzed, and bibliographic citation are given for each entry, when available. Analyses were reported most frequently for /sup 137/Cs, /sup 40/K, /sup 90/Sr, /sup 226/Ra, /sup 228/Ra, plutonium, uranium, total alpha, and total beta, but a few authors also reported data for /sup 241/Am, /sup 7/Be, /sup 60/Co, /sup 55/Fe, /sup 3/H, /sup 131/I, /sup 54/Mn, /sup 95/Nb, /sup 210/Pb, /sup 210/Po, /sup 106/Ru, /sup 125/Sb, /sup 228/Th, /sup 232/Th, and /sup 95/Zr. Based on the reported data it appears that radioactivity from alpha emitters in food crops is usually low, on the order of 0.1 Bq.g/sup -1/ (wet weight) or less. Reported values of beta radiation in a given crop generally appear to be several orders of magnitude greater than those of alpha emitters. The most striking aspect of the data is the great range of radioactivity reported for a given nuclide in similar food crops with different geographical origins.

  20. 1000–ton testing machine for cyclic fatigue tests of materials at liquid nitrogen temperatures

    SciTech Connect (OSTI)

    Khitruk, A. A.; Klimchenko, Yu. A.; Kovalchuk, O. A.; Marushin, E. L.; Mednikov, A. A.; Nasluzov, S. N.; Privalova, E. K.; Rodin, I. Yu.; Stepanov, D. B.; Sukhanova, M. V.

    2014-01-29

    One of the main tasks of superconductive magnets R and D is to determine the mechanical and fatigue properties of structural materials and the critical design elements in the cryogenic temperature range. This paper describes a new facility built based on the industrial 1000-ton (10 MN) testing machine Schenk PC10.0S. Special equipment was developed to provide the mechanical and cyclic tensile fatigue tests of large-scale samples at the liquid nitrogen temperature and in a given load range. The main feature of the developed testing machine is the cryostat, in which the device converting a standard compression force of the testing machine to the tensile force affected at the test object is placed. The control system provides the remote control of the test and obtaining, processing and presentation of test data. As an example of the testing machine operation the test program and test results of the cyclic tensile fatigue tests of fullscale helium inlet sample of the PF1 coil ITER are presented.

  1. West Valley Demonstration Project Food Drive Delivers Food for...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    grocery stores to purchase food at or below wholesale price. Volunteers help load the food into trucks, bring it to the pantries, and stock the shelves. "The support we receive...

  2. CEBAF Control Room Renovation

    SciTech Connect (OSTI)

    Michael Spata; Anthony Cuffe; Thomas Oren

    2005-03-22

    The Machine Control Center (MCC) at Jefferson Lab's Continuous Electron Beam Accelerator Facility (CEBAF) was constructed in the early 1990s and based on proven technology of that era. Through our experience over the last 15 years and in our planning for the facilities 12 GeV upgrade we reevaluated the control room environment to capitalize on emerging visualization and display technologies and improve on work-flow processes and ergonomic attributes. The renovation was performed in two phases during the summer of 2004, with one phase occurring during machine operations and the latter, more extensive phase, occurring during our semi-annual shutdown period. The new facility takes advantage of advances in display technology, analog and video signal management, server technology, ergonomic workspace design, lighting engineering, acoustic ceilings and raised flooring solutions to provide a marked improvement in the overall environment of machine operations.

  3. Rotating electric machine with fluid supported parts

    DOE Patents [OSTI]

    Smith, Jr., Joseph L. (Concord, MA); Kirtley, Jr., James L. (Brookline, MA)

    1981-01-01

    A rotating electric machine in which the armature winding thereof and other parts are supported by a liquid to withstand the mechanical stresses applied during transient overloads and the like. In particular, a narrow gap is provided between the armature winding and the stator which supports it and this gap is filled with an externally pressurized viscous liquid. The liquid is externally pressurized sufficiently to balance the static loads on the armature winding. Transient mechanical loads which deform the armature winding alter the gap dimensions and thereby additionally pressurize the viscous liquid to oppose the armature winding deformation and more nearly uniformly to distribute the resulting mechanical stresses.

  4. Refueling machine with relative positioning capability

    DOE Patents [OSTI]

    Challberg, Roy Clifford; Jones, Cecil Roy

    1998-01-01

    A refueling machine having relative positioning capability for refueling a nuclear reactor. The refueling machine includes a pair of articulated arms mounted on a refueling bridge. Each arm supports a respective telescoping mast. Each telescoping mast is designed to flex laterally in response to application of a lateral thrust on the end of the mast. A pendant mounted on the end of the mast carries an air-actuated grapple, television cameras, ultrasonic transducers and waterjet thrusters. The ultrasonic transducers are used to detect the gross position of the grapple relative to the bail of a nuclear fuel assembly in the fuel core. The television cameras acquire an image of the bail which is compared to a pre-stored image in computer memory. The pendant can be rotated until the television image and the pre-stored image match within a predetermined tolerance. Similarly, the waterjet thrusters can be used to apply lateral thrust to the end of the flexible mast to place the grapple in a fine position relative to the bail as a function of the discrepancy between the television and pre-stored images.

  5. Refueling machine with relative positioning capability

    DOE Patents [OSTI]

    Challberg, R.C.; Jones, C.R.

    1998-12-15

    A refueling machine is disclosed having relative positioning capability for refueling a nuclear reactor. The refueling machine includes a pair of articulated arms mounted on a refueling bridge. Each arm supports a respective telescoping mast. Each telescoping mast is designed to flex laterally in response to application of a lateral thrust on the end of the mast. A pendant mounted on the end of the mast carries an air-actuated grapple, television cameras, ultrasonic transducers and waterjet thrusters. The ultrasonic transducers are used to detect the gross position of the grapple relative to the bail of a nuclear fuel assembly in the fuel core. The television cameras acquire an image of the bail which is compared to a pre-stored image in computer memory. The pendant can be rotated until the television image and the pre-stored image match within a predetermined tolerance. Similarly, the waterjet thrusters can be used to apply lateral thrust to the end of the flexible mast to place the grapple in a fine position relative to the bail as a function of the discrepancy between the television and pre-stored images. 11 figs.

  6. Method for measuring the contour of a machined part

    DOE Patents [OSTI]

    Bieg, L.F.

    1995-05-30

    A method is disclosed for measuring the contour of a machined part with a contour gage apparatus, having a probe assembly including a probe tip for providing a measure of linear displacement of the tip on the surface of the part. The contour gage apparatus may be moved into and out of position for measuring the part while the part is still carried on the machining apparatus. Relative positions between the part and the probe tip may be changed, and a scanning operation is performed on the machined part by sweeping the part with the probe tip, whereby data points representing linear positions of the probe tip at prescribed rotation intervals in the position changes between the part and the probe tip are recorded. The method further allows real-time adjustment of the apparatus machining the part, including real-time adjustment of the machining apparatus in response to wear of the tool that occurs during machining. 5 figs.

  7. Method for measuring the contour of a machined part

    DOE Patents [OSTI]

    Bieg, Lothar F.

    1995-05-30

    A method for measuring the contour of a machined part with a contour gage apparatus, having a probe assembly including a probe tip for providing a measure of linear displacement of the tip on the surface of the part. The contour gage apparatus may be moved into and out of position for measuring the part while the part is still carried on the machining apparatus. Relative positions between the part and the probe tip may be changed, and a scanning operation is performed on the machined part by sweeping the part with the probe tip, whereby data points representing linear positions of the probe tip at prescribed rotation intervals in the position changes between the part and the probe tip are recorded. The method further allows real-time adjustment of the apparatus machining the part, including real-time adjustment of the machining apparatus in response to wear of the tool that occurs during machining.

  8. Framework for autonomous navigation of a continuous mining machine

    SciTech Connect (OSTI)

    Anderson, D.L.

    1989-01-01

    This report includes a discussion of the navigational tasks performed by operators of mobile mining equipment, with the focus on the navigational information and guidance techniques required by continuous mining machine operators. Some previous research and attempts in remote and autonomous navigation of continuous mining machines are mentioned. Issues of research in autonomous navigation of various other mobile robots are presented, with attention focused on their applicability to a continuous mining machine navigating in the mining environment. Conclusions are stated on methods of automating the navigational tasks of a contionuous mining machine, and a decision to concentrate intitial attempts on the tasks of autonomous face navigation is defended. This report includes a presentation of the Bureau's proposed solution for autonomous face navigation of a continous mining machine, which includes the employment of a mobile roof support as a reference for guidance in the face area, and a navigational guidance system for the continuous mining machine.

  9. Means and method of balancing multi-cylinder reciprocating machines

    DOE Patents [OSTI]

    Corey, John A.; Walsh, Michael M.

    1985-01-01

    A virtual balancing axis arrangement is described for multi-cylinder reciprocating piston machines for effectively balancing out imbalanced forces and minimizing residual imbalance moments acting on the crankshaft of such machines without requiring the use of additional parallel-arrayed balancing shafts or complex and expensive gear arrangements. The novel virtual balancing axis arrangement is capable of being designed into multi-cylinder reciprocating piston and crankshaft machines for substantially reducing vibrations induced during operation of such machines with only minimal number of additional component parts. Some of the required component parts may be available from parts already required for operation of auxiliary equipment, such as oil and water pumps used in certain types of reciprocating piston and crankshaft machine so that by appropriate location and dimensioning in accordance with the teachings of the invention, the virtual balancing axis arrangement can be built into the machine at little or no additional cost.

  10. West Pico Food | Open Energy Information

    Open Energy Info (EERE)

    Pico Food Jump to: navigation, search Name: West Pico Food Place: Vernon, California Sector: Solar Product: A distributor of wholesale frozen foods to supermarket chains in...

  11. NREL: Transportation Research - Power Electronics and Electric Machines

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Publications and Electric Machines Publications NREL and its partners have produced many papers and presentations related to power electronics and electric machines. For more information about the following publications, contact Sreekant Narumanchi. A photo of a group of researchers sitting around a table with printed publications and laptops. Reports from power electronics and electric machines research are available to the public. Photo by Pat Corkery, NREL Software Spray System Evaluation

  12. Purchasing Energy-Efficient Refrigerated Beverage Vending Machines |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Refrigerated Beverage Vending Machines Purchasing Energy-Efficient Refrigerated Beverage Vending Machines The Federal Energy Management Program (FEMP) provides acquisition guidance for refrigerated beverage vending machines, a product category covered by ENERGY STAR efficiency requirements. Federal laws and requirements mandate that agencies purchase ENERGY STAR-qualified products or FEMP-designated products in all product categories covered by these programs and in any

  13. Machine learning helps discover the most luminous supernova in history

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Machine learning helps discover supernova Machine learning helps discover the most luminous supernova in history Machine-learning technology developed at Los Alamos National Laboratory played a key role in the discovery of supernova ASASSN-15lh. January 14, 2016 An artist's impression of the record-breaking superluminous supernova ASASSN-15lh as it would appear from an exoplanet located about 10,000 light years away in the host galaxy of the supernova. (Credit: Beijing Planetarium / Jin Ma) An

  14. Energy Cost Calculator for Commercial Ice Machines | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Ice Machines Energy Cost Calculator for Commercial Ice Machines Vary capacity size, energy cost, hours of operation, and /or efficiency level. INPUT SECTION Input the following data (if any parameter is missing, calculator will set to default value). Defaults Type of Ice Cube Machine Ice Making Head Self-Contained Remote Condensing Unit Ice Making Head Type of Condenser Air Cooled Water Cooled Air Cooled Ice Harvest Rate (lbs. ice per 24 hrs.) lbs. per 24 hrs. 500 lbs. per 24 hrs. Energy

  15. Fusion Machines of the World | Princeton Plasma Physics Lab

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Fusion Machines of the World NSTX-U IS ONE OF AN ELITE GROUP of magnetic fusion facilities scattered across the globe. These powerful and complex machines are advancing mankind's quest to harness fusion as a safe, clean and abundant source of energy for producing electricity. Here is a selection of major facilities. Publication File: PDF icon NSTX-U_presskit_print_FusionMachines-World

  16. Y-12 leads the way in specialized machining

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    leads the way in specialized machining The original nine major buildings at Y-12, five "Alpha" buildings and four "Beta" buildings were originally built to house calutrons to...

  17. Next Generation Electric Machines: Megawatt Class Motors FOA Informational Webinar

    Broader source: Energy.gov [DOE]

    The Next Generation Electric Machines: Megawatt Class Motors FOA Informational Webinar will discuss standard procedures regarding the EERE Office and FOA process.

  18. Covered Product Category: Water-Cooled Ice Machines | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Covered Product Category: Water-Cooled Ice Machines The Federal Energy Management Program (FEMP) provides acquisition guidance and federal efficiency requirements for water-cooled ...

  19. Effect of Machining Procedures on the Strength of Ceramics for...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Effect of Machining Procedures on the Strength of Ceramics for Advanced Diesel Engine Applications Poster presentation at the 2007 Diesel Engine-Efficiency & Emissions Research ...

  20. Rapid Compression Machine Â… A Key Experimental Device to Effectively...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    to Effectively Collaborate with Basic Energy Sciences Rapid Compression Machine A Key Experimental Device to Effectively Collaborate with Basic Energy Sciences 2011 DOE ...

  1. DOE - Office of Legacy Management -- American Machine and Metals...

    Office of Legacy Management (LM)

    Metals Inc - IL 24 FUSRAP Considered Sites Site: American Machine and Metals Inc (IL.24 ) Eliminated from consideration under FUSRAP Designated Name: Not Designated Alternate Name:...

  2. DOE - Office of Legacy Management -- American Machine and Foundry...

    Office of Legacy Management (LM)

    Buffalo - NY 63 FUSRAP Considered Sites Site: American Machine and Foundry Co - Buffalo (NY.63 ) Eliminated from further consideration under FUSRAP Designated Name: Not Designated...

  3. Multi-winding Homopolar Electric Machine Offers Variable Voltage...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Technologies Find More Like This Return to Search Multi-winding Homopolar Electric Machine Offers Variable Voltage at Low Rotational Speed Oak Ridge National Laboratory Contact...

  4. Vision Machine & Fabrication Corp. Named Top Small Business Subcontrac...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Vision Machine & Fabrication Corp. Named Top Small Business Subcontractor at Jefferson Lab for FY 2014 NEWPORT NEWS, VA, Sept. 10, 2015 - Jefferson Science Associates, the...

  5. Using support vector machines to improve elemental ion identification...

    Office of Scientific and Technical Information (OSTI)

    elemental ions in X-ray crystal structures has been extended to use support vector machine (SVM) classifiers trained on selected structures in the PDB, with significantly...

  6. Sandia gives Japanese elected official a tour of Z machine |...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    gives Japanese elected official a tour of Z machine | National Nuclear Security Administration Facebook Twitter Youtube Flickr RSS People Mission Managing the Stockpile Preventing...

  7. John Hsu, Oak Ridge National Laboratory, Flux Coupling Machines...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    John Hsu, Oak Ridge National Laboratory, Flux Coupling Machines and Switched Reluctance Motors to Replace Permanent Magnets in Electric Vehicles John Hsu, Oak Ridge National...

  8. Overcoming residual stresses and machining distortion in the...

    Office of Scientific and Technical Information (OSTI)

    in the production of aluminum alloy satellite boxes. Citation Details In-Document Search Title: Overcoming residual stresses and machining distortion in the production of ...

  9. DOE - Office of Legacy Management -- Cincinnati Milling and Machining...

    Office of Legacy Management (LM)

    & Machining Co. (OH.25 ) Eliminated from consideration under FUSRAP - Referred to NRC Designated Name: Not Designated Alternate Name: None Location: Cincinnati , Ohio...

  10. Purchasing Energy-Efficient Air-Cooled Ice Machines | Department...

    Broader source: Energy.gov (indexed) [DOE]

    Federal Energy Management Program (FEMP) provides acquisition guidance for air-cooled ice machines, a product category covered by ENERGY STAR efficiency requirements. Federal laws ...

  11. Machine Learning Techniques Applied to Sensor Data Correction...

    Office of Scientific and Technical Information (OSTI)

    Center Sponsoring Org: ORNL LDRD Director's R&D Country of Publication: United States Language: English Subject: sensor data validation; building technologies; machine learning

  12. Logomatic Gmbh Grinding Machines Fabrication | Open Energy Information

    Open Energy Info (EERE)

    Machines Fabrication Place: Mainaschaff, Germany Zip: D-63814 Sector: Solar Product: German manufacturer of capital equipment for semiconductor and solar industries; for solar,...

  13. Covered Product Category: Air-Cooled Ice Machines

    Broader source: Energy.gov [DOE]

    The Federal Energy Management Program (FEMP) provides acquisition guidance for air-cooled ice machines, which are covered by the ENERGY STAR program.

  14. Stabilized free-piston Stirling cycle machine

    SciTech Connect (OSTI)

    Emigh, S.G.; White, M.A.; Kennewich, P.R.

    1990-11-06

    This patent describes a free piston Stirling cycle machine. It comprises: a displacer cylinder having a central cylindrical axis; a displacer located within the displacer cylinder and movably mounted along the axis; an enclosed gas spring; working gas means including an enclosed volume of pressurized working gas directed to opposite axial ends of the displacer for cyclically reciprocating the displacer along its axis in a Stirling cycle mode of operation; counterbalance means mounted for axial motion directly related to that of the displacer, stabilizer means mechanically coupled to the counterbalance means for cyclically constraining reciprocating axial motion of the counterbalance means in a repetitive pattern; and hydrostatic fluid means operatively coupling the counterbalance means to the gas spring for accommodating fluid volumetric displacement due to engine operation, the hydrostatic fluid means also being operably coupling the displacer and counterbalance means for imparting axial movement between them.

  15. Highly accurate articulated coordinate measuring machine

    DOE Patents [OSTI]

    Bieg, Lothar F.; Jokiel, Jr., Bernhard; Ensz, Mark T.; Watson, Robert D.

    2003-12-30

    Disclosed is a highly accurate articulated coordinate measuring machine, comprising a revolute joint, comprising a circular encoder wheel, having an axis of rotation; a plurality of marks disposed around at least a portion of the circumference of the encoder wheel; bearing means for supporting the encoder wheel, while permitting free rotation of the encoder wheel about the wheel's axis of rotation; and a sensor, rigidly attached to the bearing means, for detecting the motion of at least some of the marks as the encoder wheel rotates; a probe arm, having a proximal end rigidly attached to the encoder wheel, and having a distal end with a probe tip attached thereto; and coordinate processing means, operatively connected to the sensor, for converting the output of the sensor into a set of cylindrical coordinates representing the position of the probe tip relative to a reference cylindrical coordinate system.

  16. Radioactive hot cell access hole decontamination machine

    DOE Patents [OSTI]

    Simpson, William E.

    1982-01-01

    Radioactive hot cell access hole decontamination machine. A mobile housing has an opening large enough to encircle the access hole and has a shielding door, with a door opening and closing mechanism, for uncovering and covering the opening. The housing contains a shaft which has an apparatus for rotating the shaft and a device for independently translating the shaft from the housing through the opening and access hole into the hot cell chamber. A properly sized cylindrical pig containing wire brushes and cloth or other disks, with an arrangement for releasably attaching it to the end of the shaft, circumferentially cleans the access hole wall of radioactive contamination and thereafter detaches from the shaft to fall into the hot cell chamber.

  17. Mining machine with cutter drums and sensing apparatus

    SciTech Connect (OSTI)

    Borowski, K.

    1980-02-19

    A drum cutter for a mining machine includes spaced-apart pick elements projecting radially therefrom and a disc forming part of a sensing apparatus disposed to follow a preceding one of the pick elements through rotational movement of the drum cutter. A disc is mounted by a pivot pin extending generally parallel with the rotational axis of the drum cutter. A sensor responds to the radial loading on the disc and produces a signal delivered to a controller for an actuator coupled to a pivot arm carrying the drum cutter. The disc is mounted to project radially about 10-20 millimeters beyond the radially-projected distance by a pick element. The sensor is a strain gage, a piezoelectric gage, an induction gage, a capacitive gage or a load cell. The sensor may be mounted within a hydraulically-power piston and cylinder assembly forming the actuator for the pivot arm. When a load cell is used, it filters out and detects pressure variations at peak magnitudes occurring as the disc penetrates the mine face with a rhythmic rotation for producing corresponding electric signals that are delivered to the controller for the pivot arm.

  18. Spectral output of Z-machine implosions.

    SciTech Connect (OSTI)

    Idzorek, G. C.; Chrien, Robert E.; Peterson, D. L.; Watt, R. G.; Chandler, G. A.; Fehl, D. L.; Sanford, T. W. L.

    2001-01-01

    Sandia National Laboratories Z-machine has developed into a reproducible, high power (>200 TW), high temperature (>200 eV) driver for radiation physics experiments. Imploding cylindrical wire arrays on the Z-machine produce a radiation source with a bolometric temperature of about 200 eV. By surrounding the z-pinch implosion with a vacuum hohlraum a nearly Planckian source of about 140 eV temperature is created with peak radiation powers of about 200 terawatts and integrated energy of 2 megajoules or more. In this energy rich environment we can field a dozen experiments all being driven by an identical source. In addition to 'standard' vacuum hohlraums we also use dynamic hohlraums consisting of two nested wire arrays converging onto an axially centered foam cylinder. Radiation flowing from the ends on the cylinder indicates a Planckian source temperature well over 200 eV. Only two experiments can be fielded on a dynamic hohlraum (one on each end) but the higher source temperature justifies the added complexity of the set-up. We routinely use arrays of filtered silicon photodiodes (SiD) and filtered photocathode x-ray diodes (XRD) to determine the temperature of the source. Three different techniques for unfolding spectra from the XRD and SiD detector data are being used. They are: (1) Treat each detector independently and find the Planckian temperature for a given source size and solid angle that would give the measured detector signal, (2) Use all detector signals and detector spectral responses simultaneously and find a spectrum that best fits the observed data, (3) Use all detector signals and averaged detector spectral responses and find a histogram spectrum that best fits the observed data. When used as complementary set of analysis tools these techniques generate remarkably consistent results showing nearly Planckian behavior on our vacuum hohlraum experiments.

  19. Flat Ge-doped optical fibres for food irradiation dosimetry

    SciTech Connect (OSTI)

    Noor, N. Mohd; Jusoh, M. A.; Razis, A. F. Abdull; Alawiah, A.; Bradley, D. A.

    2015-04-24

    Exposing food to radiation can improve hygiene quality, germination control, retard sprouting, and enhance physical attributes of the food product. To provide for food safety, radiation dosimetry in irradiated food is required. Herein, fabricated germanium doped (Ge-doped) optical fibres have been used. The fibres have been irradiated using a gamma source irradiator, doses in the range 1 kGy to 10 kGy being delivered. Using Ge-doped optical fibres of variable size, type and dopant concentration, study has been made of linearity, reproducibility, and fading. The thermoluminescence (TL) yield of the fibres were obtained and compared. The fibres exhibit a linear dose response over the investigated range of doses, with mean reproducibility to within 2.69 % to 8.77 %, exceeding the dose range of all commercial dosimeters used in evaluating high doses for the food irradiation industry. TL fading of the Ge-doped flat fibres has been found to be < 13%.

  20. Feature Based Machining Process Planning V5.1

    Energy Science and Technology Software Center (OSTI)

    2001-07-30

    The purpose of the FB-Machining Advisor product is to provide industry with an end user product that will enable end users to more effectively interact with a solid model for manufacturing applications. The product allows end users to visualize and organize their manufacturing process plans as they are being conceived; avoid redundant and time consuming geometric construction and calculation; automate geometric reasoning processes, and automate downstream manufacturing applications. The product augments a solid model representationmore » of the part with a set of machining features (e.g., pockets, steps, holes, cutouts). The product also enables end users to interact with a solid model to create process plans. It will automatically recognize, or interactively create and modify surface based machining features (represented by sets of faces on the solid model) and volumetric machining features which are represented by delta volumes (solid bodies representing volumes of material to be removed from the part). The FB-Machining Advisor will generate “in process shapes” that represent the shape of the work piece prior or subsequent to a material removal operation. It is designed to facilitate process change propagation in order to minimize rework resulting from process modifications. The machining features will provide vital shape and tolerance information (i.e. depth of pocket, minimum side radius of pocket, diameter of hole, maximum surface finish of side walls). The FB-Machining Advisor also integrates solid model based (3 Dimensional) tolerance information with the machining feature representations.« less

  1. Traction sheave elevator, hoisting unit and machine space

    DOE Patents [OSTI]

    Hakala, Harri; Mustalahti, Jorma; Aulanko, Esko

    2000-01-01

    Traction sheave elevator consisting of an elevator car moving along elevator guide rails, a counterweight moving along counterweight guide rails, a set of hoisting ropes (3) on which the elevator car and counterweight are suspended, and a drive machine unit (6) driving a traction sheave (7) acting on the hoisting ropes (3) and placed in the elevator shaft. The drive machine unit (6) is of a flat construction. A wall of the elevator shaft is provided with a machine space with its open side facing towards the shaft, the essential parts of the drive machine unit (6) being placed in the space. The hoisting unit (9) of the traction sheave elevator consists of a substantially discoidal drive machine unit (6) and an instrument panel (8) mounted on the frame (20) of the hoisting unit.

  2. Food Service | Open Energy Information

    Open Energy Info (EERE)

    Building Types 1 References EIA CBECS Building Types U.S. Energy Information Administration (Oct 2008) Retrieved from "http:en.openei.orgwindex.php?titleFoodService&old...

  3. Food Sales | Open Energy Information

    Open Energy Info (EERE)

    Building Types 1 References EIA CBECS Building Types U.S. Energy Information Administration (Oct 2008) Retrieved from "http:en.openei.orgwindex.php?titleFoodSales&oldid...

  4. Method and radial gap machine for high strength undiffused brushless operation

    DOE Patents [OSTI]

    Hsu, John S.

    2006-10-31

    A radial gap brushless electric machine (30) having a stator (31) and a rotor (32) and a main air gap (34) also has at least one stationary excitation coil (35a, 36a) separated from the rotor (32) by a secondary air gap (35e, 35f, 36e, 36f) so as to induce a secondary flux in the rotor (32) which controls a resultant flux in the main air gap (34). Permanent magnetic (PM) material (38) is disposed in spaces between the rotor pole portions (39) to inhibit the second flux from leaking from the pole portions (39) prior to reaching the main air gap (34). By selecting the direction of current in the stationary excitation coil (35a, 36a) both flux enhancement and flux weakening are provided for the main air gap (34). A method of non-diffused flux enhancement and flux weakening for a radial gap machine is also disclosed.

  5. LTC vacuum blasting machine (concrete): Baseline report

    SciTech Connect (OSTI)

    1997-07-31

    The LTC shot blast technology was tested and is being evaluated at Florida International University (FIU) as a baseline technology. In conjunction with FIU`s evaluation of efficiency and cost, this report covers the evaluation conducted for safety and health issues. It is a commercially available technology and has been used for various projects at locations throughout the country. The LTC 1073 Vacuum Blasting Machine uses a high-capacity, direct-pressure blasting system which incorporates a continuous feed for the blast media. The blast media cleans the surface within the contained brush area of the blast. It incorporates a vacuum system which removes dust and debris from the surface as it is blasted. The safety and health evaluation during the testing demonstration focused on two main areas of exposure: dust and noise. Dust exposure during maintenance activities was minimal, but due to mechanical difficulties dust monitoring could not be conducted during operation. Noise exposure was significant. Further testing for each of these exposures is recommended because of the outdoor environment where the testing demonstration took place. This may cause the results to be inaccurate. It is feasible that the dust and noise levels will be higher in an enclosed environment. In addition, other safety and health issues found were ergonomics, heat stress, tripping hazards, electrical hazards, lockout/tagout, and arm-hand vibration.

  6. LTC vacuum blasting machine (metal): Baseline report

    SciTech Connect (OSTI)

    1997-07-31

    The LTC coating removal technology was tested and is being evaluated at Florida International University (FIU) as a baseline technology. In conjunction with evaluation of efficiency and cost, this report covers the evaluation conducted for safety and health issues. It is a commercially available technology and has been used for various projects at locations throughout the country. The LTC coating removal system consisted of several hand tools, a Roto Peen scaler, and a needlegun. They are designed to remove coatings from steel, concrete, brick, and wood. These hand tools are used with the LTC PTC-6 vacuum system to capture dust and debris as removal of the coating takes place. The safety and health evaluation during the testing demonstration focused on two main areas of exposure: dust and noise. The dust exposure was minimal but noise exposure was significant. Further testing for each exposure is recommended because of the environment where the testing demonstration took place. It is feasible that the dust and noise levels will be higher in an enclosed operating environment of different construction. In addition, other areas of concern found were arm-hand vibration, whole-body vibration, ergonomics, heat stress, tripping hazards, electrical hazards, machine guarding, and lockout/tagout.

  7. Method for laser machining explosives and ordnance

    DOE Patents [OSTI]

    Muenchausen, Ross E.; Rivera, Thomas; Sanchez, John A.

    2003-05-06

    Method for laser machining explosives and related articles. A laser beam is directed at a surface portion of a mass of high explosive to melt and/or vaporize the surface portion while directing a flow of gas at the melted and/or vaporized surface portion. The gas flow sends the melted and/or vaporized explosive away from the charge of explosive that remains. The method also involves splitting the casing of a munition having an encased explosive. The method includes rotating a munition while directing a laser beam to a surface portion of the casing of an article of ordnance. While the beam melts and/or vaporizes the surface portion, a flow of gas directed at the melted and/or vaporized surface portion sends it away from the remaining portion of ordnance. After cutting through the casing, the beam then melts and/or vaporizes portions of the encased explosive and the gas stream sends the melted/vaporized explosive away from the ordnance. The beam is continued until it splits the article, after which the encased explosive, now accessible, can be removed safely for recycle or disposal.

  8. Method and machine for high strength undiffused brushless operation

    DOE Patents [OSTI]

    Hsu, John S.

    2003-06-03

    A brushless electric machine (30) having a stator (31) and a rotor (32) and a main air gap (34), the rotor (32) having pairs of rotor pole portions (22b, 22c, 32f, 32l) disposed at least partly around the axis of rotation (32p) and facing the main air gap (24b, 24c, 34), at least one stationary winding (20b, 20c, 33b) separated from the rotor (22b, 22c, 32) by a secondary air gap (23b, 23c, 35) so as to induce a rotor-side flux in the rotor (22b, 22c, 32) which controls a resultant flux in the main air gap (24b, 24c, 34). PM material (27b, 27c) is disposed in spaces between the rotor pole portions (22b, 22c, 32f, 32l) to inhibit the rotor-side flux from leaking from said pole portions (22b, 22c, 32f, 32l) prior to reaching the main air gap (24b, 24c, 34). By selecting the direction of current in the stationary winding (20b, 20c, 33b) both flux enhancement and flux weakening are provided for the main air gap (24b, 24c, 34). The stationary windings (31a, 33b) which are used for both primary and secondary excitation allow for easier adaptation to cooling systems as described. A method of non-diffused flux enhancement and flux weakening is also disclosed.

  9. Rotor apparatus for high strength undiffused brushless electric machine

    DOE Patents [OSTI]

    Hsu, John S [Oak Ridge, TN

    2006-01-24

    A radial gap brushless electric machine (30) having a stator (31) and a rotor (32) and a main air gap (34) also has at least one stationary excitation coil (35a, 36a) separated from the rotor (32) by a secondary air gap (35e, 35f, 36e, 36f) so as to induce a secondary flux in the rotor (32) which controls a resultant flux in the main air gap (34). Permanent magnetic (PM) material (38) is disposed in spaces between the rotor pole portions (39) to inhibit the second flux from leaking from the pole portions (39) prior to reaching the main air gap (34). By selecting the direction of current in the stationary excitation coil (35a, 36a) both flux enhancement and flux weakening are provided for the main air gap (34). Improvements of a laminated rotor, an end pole structure, and an arrangement of the PM elements for providing an arrangement of the flux paths from the auxiliary field coil assemblies are also disclosed.

  10. Automatic ball bar for a coordinate measuring machine

    DOE Patents [OSTI]

    Jostlein, H.

    1997-07-15

    An automatic ball bar for a coordinate measuring machine determines the accuracy of a coordinate measuring machine having at least one servo drive. The apparatus comprises a first and second gauge ball connected by a telescoping rigid member. The rigid member includes a switch such that inward radial movement of the second gauge ball relative to the first gauge ball causes activation of the switch. The first gauge ball is secured in a first magnetic socket assembly in order to maintain the first gauge ball at a fixed location with respect to the coordinate measuring machine. A second magnetic socket assembly secures the second gauge ball to the arm or probe holder of the coordinate measuring machine. The second gauge ball is then directed by the coordinate measuring machine to move radially inward from a point just beyond the length of the ball bar until the switch is activated. Upon switch activation, the position of the coordinate measuring machine is determined and compared to known ball bar length such that the accuracy of the coordinate measuring machine can be determined. 5 figs.

  11. Automatic ball bar for a coordinate measuring machine

    DOE Patents [OSTI]

    Jostlein, Hans

    1997-01-01

    An automatic ball bar for a coordinate measuring machine determines the accuracy of a coordinate measuring machine having at least one servo drive. The apparatus comprises a first and second gauge ball connected by a telescoping rigid member. The rigid member includes a switch such that inward radial movement of the second gauge ball relative to the first gauge ball causes activation of the switch. The first gauge ball is secured in a first magnetic socket assembly in order to maintain the first gauge ball at a fixed location with respect to the coordinate measuring machine. A second magnetic socket assembly secures the second gauge ball to the arm or probe holder of the coordinate measuring machine. The second gauge ball is then directed by the coordinate measuring machine to move radially inward from a point just beyond the length of the ball bar until the switch is activated. Upon switch activation, the position of the coordinate measuring machine is determined and compared to known ball bar length such that the accuracy of the coordinate measuring machine can be determined.

  12. Alternator control for battery charging

    DOE Patents [OSTI]

    Brunstetter, Craig A.; Jaye, John R.; Tallarek, Glen E.; Adams, Joseph B.

    2015-07-14

    In accordance with an aspect of the present disclosure, an electrical system for an automotive vehicle has an electrical generating machine and a battery. A set point voltage, which sets an output voltage of the electrical generating machine, is set by an electronic control unit (ECU). The ECU selects one of a plurality of control modes for controlling the alternator based on an operating state of the vehicle as determined from vehicle operating parameters. The ECU selects a range for the set point voltage based on the selected control mode and then sets the set point voltage within the range based on feedback parameters for that control mode. In an aspect, the control modes include a trickle charge mode and battery charge current is the feedback parameter and the ECU controls the set point voltage within the range to maintain a predetermined battery charge current.

  13. Graphite fiber reinforced structure for supporting machine tools

    DOE Patents [OSTI]

    Knight, Jr., Charles E.; Kovach, Louis; Hurst, John S.

    1978-01-01

    Machine tools utilized in precision machine operations require tool support structures which exhibit minimal deflection, thermal expansion and vibration characteristics. The tool support structure of the present invention is a graphite fiber reinforced composite in which layers of the graphite fibers or yarn are disposed in a 0/90.degree. pattern and bonded together with an epoxy resin. The finished composite possesses a low coefficient of thermal expansion and a substantially greater elastic modulus, stiffness-to-weight ratio, and damping factor than a conventional steel tool support utilized in similar machining operations.

  14. Water spray ventilator system for continuous mining machines

    DOE Patents [OSTI]

    Page, Steven J.; Mal, Thomas

    1995-01-01

    The invention relates to a water spray ventilator system mounted on a continuous mining machine to streamline airflow and provide effective face ventilation of both respirable dust and methane in underground coal mines. This system has two side spray nozzles mounted one on each side of the mining machine and six spray nozzles disposed on a manifold mounted to the underside of the machine boom. The six spray nozzles are angularly and laterally oriented on the manifold so as to provide non-overlapping spray patterns along the length of the cutter drum.

  15. Power Electronics and Electrical Machines Review, August 2006 | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy Electrical Machines Review, August 2006 Power Electronics and Electrical Machines Review, August 2006 This report is a summary of the Review Panel at the FY06 DOE FreedomCAR and Vehicle Technologies (FCVT) Annual Review of Advanced Power Electronics and Electric Machine (APEEM) research activities held on August 15-17, 2006. PDF icon Annual Review Report More Documents & Publications FY 2011 Annual Progress Report for Energy Storage R&D FY 2011 Annual Progress Report for

  16. Flotation machine and process for removing impurities from coals

    DOE Patents [OSTI]

    Szymocha, K.; Ignasiak, B.; Pawlak, W.; Kulik, C.; Lebowitz, H.E.

    1997-02-11

    The present invention is directed to a type of flotation machine that combines three separate operations in a single unit. The flotation machine is a hydraulic separator that is capable of reducing the pyrite and other mineral matter content of a coal. When the hydraulic separator is used with a flotation system, the pyrite and certain other minerals particles that may have been entrained by hydrodynamic forces associated with conventional flotation machines and/or by the attachment forces associated with the formation of microagglomerates are washed and separated from the coal. 4 figs.

  17. Flotation machine and process for removing impurities from coals

    DOE Patents [OSTI]

    Szymocha, K.; Ignasiak, B.; Pawlak, W.; Kulik, C.; Lebowitz, H.E.

    1995-12-05

    The present invention is directed to a type of flotation machine that combines three separate operations in a single unit. The flotation machine is a hydraulic separator that is capable of reducing the pyrite and other mineral matter content of a coal. When the hydraulic separator is used with a flotation system, the pyrite and certain other mineral particles that may have been entrained by hydrodynamic forces associated with conventional flotation machines and/or by the attachment forces associated with the formation of microagglomerates are washed and separated from the coal. 4 figs.

  18. Flotation machine and process for removing impurities from coals

    DOE Patents [OSTI]

    Szymocha, Kazimierz; Ignasiak, Boleslaw; Pawlak, Wanda; Kulik, Conrad; Lebowitz, Howard E.

    1997-01-01

    The present invention is directed to a type of flotation machine that combines three separate operations in a single unit. The flotation machine is a hydraulic separator that is capable of reducing the pyrite and other mineral matter content of a coal. When the hydraulic separator is used with a flotation system, the pyrite and certain other minerals particles that may have been entrained by hydrodynamic forces associated with conventional flotation machines and/or by the attachment forces associated with the formation of microagglomerates are washed and separated from the coal.

  19. Flotation machine and process for removing impurities from coals

    DOE Patents [OSTI]

    Szymocha, Kazimierz; Ignasiak, Boleslaw; Pawlak, Wanda; Kulik, Conrad; Lebowitz, Howard E.

    1995-01-01

    The present invention is directed to a type of flotation machine that combines three separate operations in a single unit. The flotation machine is a hydraulic separator that is capable of reducing the pyrite and other mineral matter content of a coal. When the hydraulic separator is used with a flotation system, the pyrite and certain other minerals particles that may have been entrained by hydrodynamic forces associated with conventional flotation machines and/or by the attachment forces associated with the formation of microagglomerates are washed and separated from the coal.

  20. System and method for cooling a superconducting rotary machine

    DOE Patents [OSTI]

    Ackermann, Robert Adolf (Schenectady, NY); Laskaris, Evangelos Trifon (Schenectady, NY); Huang, Xianrui (Clifton Park, NY); Bray, James William (Niskayuna, NY)

    2011-08-09

    A system for cooling a superconducting rotary machine includes a plurality of sealed siphon tubes disposed in balanced locations around a rotor adjacent to a superconducting coil. Each of the sealed siphon tubes includes a tubular body and a heat transfer medium disposed in the tubular body that undergoes a phase change during operation of the machine to extract heat from the superconducting coil. A siphon heat exchanger is thermally coupled to the siphon tubes for extracting heat from the siphon tubes during operation of the machine.

  1. Excitation system for rotating synchronous machines

    DOE Patents [OSTI]

    Umans, Stephen D.; Driscoll, David J.

    2002-01-01

    A system for providing DC current to a rotating superconducting winding is provided. The system receives current feedback from the superconducting winding and determines an error signal based on the current feedback and a reference signal. The system determines a control signal corresponding to the error signal and provides a positive and negative superconducting winding excitation voltage based on the control signal.

  2. DOE - Office of Legacy Management -- Heald Machine Co - MA 15

    Office of Legacy Management (LM)

    Location: Worcester , Massachusetts MA.15-1 Evaluation Year: 1994 MA.15-2 MA.15-3 Site Operations: Research and development on uranium slug drilling machines in the early 1960s. ...

  3. Inventors in Action: Extreme Subsea Machines | GE Global Research

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Sabedotti, Offshore and Subsea Systems COE leader, took questions about the extreme machines used in oil and gas recovery and processing on the ocean floor during a Google Hangout. ...

  4. High Metal Removal Rate Process for Machining Difficult Materials

    Broader source: Energy.gov [DOE]

    The goal of the project is to develop an automated, ultrafast laser machining device that will be used to prototype GDI injectors. The platform will turn CAD drawings into high-precision prototypes.

  5. Driving Research in Electric Machines |GE Global Research

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Driving Research in Electric Machines Click to email this to a friend (Opens in new window) Share on Facebook (Opens in new window) Click to share (Opens in new window) Click to...

  6. Remembering the long day's journey to a historic machine's Christmas...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Remembering the long day's journey to a historic machine's Christmas Eve first plasma By John Greenwald December 21, 2012 Tweet Widget Google Plus One Share on Facebook The big...

  7. An object-oriented extension for debugging the virtual machine

    SciTech Connect (OSTI)

    Pizzi, R.G. Jr.

    1994-12-01

    A computer is nothing more then a virtual machine programmed by source code to perform a task. The program`s source code expresses abstract constructs which are compiled into some lower level target language. When a virtual machine breaks, it can be very difficult to debug because typical debuggers provide only low-level target implementation information to the software engineer. We believe that the debugging task can be simplified by introducing aspects of the abstract design and data into the source code. We introduce OODIE, an object-oriented extension to programming languages that allows programmers to specify a virtual environment by describing the meaning of the design and data of a virtual machine. This specification is translated into symbolic information such that an augmented debugger can present engineers with a programmable debugging environment specifically tailored for the virtual machine that is to be debugged.

  8. Micro transport machine and methods for using same

    DOE Patents [OSTI]

    Stalford, Harold

    2015-10-13

    A micro transport machine may include a substrate and a movable device comprising a drive component responsive to a wireless power source. The movable device is operable to move between a plurality of disparate areas on the substrate.

  9. Power Electronics and Electrical Machines Review, August 2006...

    Office of Environmental Management (EM)

    Power Electronics and Electrical Machines Review, August 2006 This report is a summary of the Review Panel at the FY06 DOE FreedomCAR and Vehicle Technologies (FCVT) Annual Review ...

  10. A Machine Learning System for Recognizing Subclasses (Demo)

    SciTech Connect (OSTI)

    Vatsavai, Raju

    2012-01-01

    Thematic information extraction from remote sensing images is a complex task. In this demonstration, we present *Miner machine learning system. In particular, we demonstrate an advanced subclass recognition algorithm that is specifically designed to extract finer classes from aggregate classes.

  11. Mineral mining machine cutter driving mechanism having a load sensing device to regulate the haulage speed of the machine when the cutter driving mechanism is overloaded

    SciTech Connect (OSTI)

    Wilson, S.L.

    1981-05-26

    A mineral mining machine is disclosed that has a haulage drive mechanism and at least one cutter drive unit for cutting elements which may be at each end of the mining machine. The cutting elements are driven by an electric motor through a variable speed gear-train and the haulage mechanism is driven by a hydraulic motor through a geartrain. The invention provides for a torque sensing device associated with a part of each cutter drive mechanism to sense the power transmitted by the cutter gear-train and a power sensing device associated with the electric motor. The torque sensing devices are in the form of a mechanical or electrical transducer which provides a signal when the power transmitted by the cutter gear-trains exceed or tends to exceed the rated value of the cutter gears. The signal is transmitted to a hydraulic pump to control the output to the hydraulic motor and thereby effect reduction of the haulage speed. A signal from the power sensing device also controls the hydraulic pump to effect reduction of the haulage speed.

  12. Proton storage ring: man/machine interface

    SciTech Connect (OSTI)

    Lander, R.F.; Clout, P.N.

    1985-01-01

    The human interface of the Proton Storage Ring Control System at Los Alamos is described in some detail, together with the software environment in which operator interaction programs are written. Some examples of operator interaction programs are given.

  13. Machine Learning Techniques Applied to Sensor Data Correction in Building

    Office of Scientific and Technical Information (OSTI)

    Technologies (Conference) | SciTech Connect Machine Learning Techniques Applied to Sensor Data Correction in Building Technologies Citation Details In-Document Search Title: Machine Learning Techniques Applied to Sensor Data Correction in Building Technologies Since commercial and residential buildings account for nearly half of the United States' energy consumption, making them more energy-efficient is a vital part of the nation's overall energy strategy. Sensors play an important role in

  14. Machine Learning for the Grid (Conference) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    Conference: Machine Learning for the Grid Citation Details In-Document Search Title: Machine Learning for the Grid Authors: Deka, Deepjyoti [1] ; Backhaus, Scott N. [1] ; Chertkov, Michael [1] ; Lokhov, Andrey [1] ; Misra, Sidhant [1] ; Vuffray, Marc Denis [1] ; Dvijotham, Krishnamurthy [1] + Show Author Affiliations Los Alamos National Laboratory Publication Date: 2016-02-02 OSTI Identifier: 1237248 Report Number(s): LA-UR-16-20576 DOE Contract Number: AC52-06NA25396 Resource Type: Conference

  15. Machine learning strategy for accelerated design of polymer dielectrics

    Office of Scientific and Technical Information (OSTI)

    (Journal Article) | SciTech Connect Machine learning strategy for accelerated design of polymer dielectrics Citation Details In-Document Search Title: Machine learning strategy for accelerated design of polymer dielectrics The ability to efficiently design new and advanced dielectric polymers is hampered by the lack of sufficient, reliable data on wide polymer chemical spaces, and the difficulty of generating such data given time and computational/experimental constraints. Here, we address

  16. Steady State Advanced Tokamak (SSAT): The mission and the machine

    Office of Scientific and Technical Information (OSTI)

    (Technical Report) | SciTech Connect Technical Report: Steady State Advanced Tokamak (SSAT): The mission and the machine Citation Details In-Document Search Title: Steady State Advanced Tokamak (SSAT): The mission and the machine Extending the tokamak concept to the steady state regime and pursuing advances in tokamak physics are important and complementary steps for the magnetic fusion energy program. The required transition away from inductive current drive will provide exciting

  17. Steady State Advanced Tokamak (SSAT): The mission and the machine

    Office of Scientific and Technical Information (OSTI)

    (Technical Report) | SciTech Connect Technical Report: Steady State Advanced Tokamak (SSAT): The mission and the machine Citation Details In-Document Search Title: Steady State Advanced Tokamak (SSAT): The mission and the machine Extending the tokamak concept to the steady state regime and pursuing advances in tokamak physics are important and complementary steps for the magnetic fusion energy program. The required transition away from inductive current drive will provide exciting

  18. Technology of mirror machines: LLL facilities for magnetic mirror fusion

    Office of Scientific and Technical Information (OSTI)

    experiments (Conference) | SciTech Connect Technology of mirror machines: LLL facilities for magnetic mirror fusion experiments Citation Details In-Document Search Title: Technology of mirror machines: LLL facilities for magnetic mirror fusion experiments Significant progress in plasma confinement and temperature has been achieved in the 2XIIB facility at Livermore. These encouraging results, and their theoretical corroboration, have provided a firm basis for the design of a new generation

  19. DOE Announces Webinars on Next Generation Electric Machines, Zero Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Buildings, and More | Department of Energy Next Generation Electric Machines, Zero Energy Buildings, and More DOE Announces Webinars on Next Generation Electric Machines, Zero Energy Buildings, and More March 26, 2015 - 8:44am Addthis EERE offers webinars to the public on a range of subjects, from adopting the latest energy efficiency and renewable energy technologies, to training for the clean energy workforce. Webinars are free; however, advanced registration is typically required. You can

  20. NREL: Transportation Research - Power Electronics and Electric Machines

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Facilities and Electric Machines Facilities NREL's power electronics and electric machines thermal management test facilities feature a wide range of equipment and enable world-class experimental and modeling capabilities. NREL researchers excel at testing and measurement in the areas of heat transfer, reliability characterization, and thermal and thermomechanical modeling. The following list describes NREL's innovative testing capabilities and equipment. A photo of four researchers in

  1. Funding Opportunity: Next Generation Electric Machines: Megawatt Class

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Motors | Department of Energy Funding Opportunity: Next Generation Electric Machines: Megawatt Class Motors Funding Opportunity: Next Generation Electric Machines: Megawatt Class Motors March 19, 2015 - 4:45pm Addthis This Funding Opportunity Announcement (FOA) is focused on developing MV integrated drive systems that leverage the benefits of state of the art power electronics (i.e., wide band gap devices) with energy efficient, high speed, direct drive, megawatt (MW) class electric motors

  2. Los Alamos's portable MRI machine may benefit New Mexicans

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Los Alamos's portable MRI machine Community Connections: Your link to news and opportunities from Los Alamos National Laboratory Latest Issue:May 2016 all issues All Issues » submit Los Alamos's portable MRI machine may benefit New Mexicans New technology may serve New Mexico's rural communities. April 4, 2016 Los Alamos experts have developed a smaller, less expensive MRI system to serve the battlefield setting and beyond. Los Alamos experts, engineer Al Urbaitis and physicist Per Magnelind,

  3. Be a Lean, Mean, Green Eating Machine | Department of Energy

    Energy Savers [EERE]

    Be a Lean, Mean, Green Eating Machine Be a Lean, Mean, Green Eating Machine January 31, 2012 - 2:53pm Addthis Kristin Swineford Communication Specialist, Weatherization and Intergovernmental Programs Like most Americans, I watched the State of the Union to hear President Obama outline his goals for the year ahead, to understand his energy outlook and plans, and of course, to see what Michelle would be wearing (a stunning royal blue, of course). When listening to the President highlight his

  4. Machine learning accelerates the discovery of new materials

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    News Releases » News Releases - 2016 » May » Machine learning accelerates the discovery of new materials Machine learning accelerates the discovery of new materials Researchers recently demonstrated how an informatics-based adaptive design strategy, tightly coupled to experiments, can accelerate the discovery of new materials with targeted properties. May 9, 2016 Adaptive design framework. Adaptive design framework. Contact Nancy Ambrosiano Communications Office (505) 667-0471 Email

  5. Vision Machine & Fabrication Corp. Named Top Small Business Subcontractor

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    at Jefferson Lab for FY 2014 | Jefferson Lab Vision Machine & Fabrication Corp. Named Top Small Business Subcontractor at Jefferson Lab for FY 2014 Vision Machine & Fabrication Corp. Named Top Small Business Subcontractor at Jefferson Lab for FY 2014 NEWPORT NEWS, VA, Sept. 10, 2015 - Jefferson Science Associates, the operations and management contractor for the Department of Energy's Thomas Jefferson National Accelerator Facility, has presented its fiscal year 2014 Outstanding Small

  6. Adjustable Portable Tensile Testing Machine | Princeton Plasma Physics Lab

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Adjustable Portable Tensile Testing Machine Thise invention describes a load-testing device that allows users to apply a load or force to any item. Additionally, this device allows users to operate the item while the load is applied to provide both static as well as dynamic capacities. The load-testing machine is adjustable to accommodate various desired loads and is also portable, allowing tests to be performed at various locations. No.: M-890 Inventor(s): Michael E Viola

  7. Silicon Micromachined Dimensional Calibration Artifact for Mesoscale Measurement Machines

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Micromachined Dimensional Calibration Artifact for Mesoscale Measurement Machines 1 Silicon Micromachined Dimensional Calibration Artifact for Mesoscale Measurement Machines 2 Sandia National Laboratories PO Box 5800 Albuquerque, NM 87185 USA Hy D. Tran, PhD, PE Phone: (505)844-5417 Fax: (505)844-4372 hdtran@sandia.gov AFFIRMATION: I affirm that all information submitted as a part of, or supplemental to, this entry is a fair and accurate representation of this product.

  8. Ultrashort pulse laser machining of metals and alloys

    DOE Patents [OSTI]

    Perry, Michael D.; Stuart, Brent C.

    2003-09-16

    The invention consists of a method for high precision machining (cutting, drilling, sculpting) of metals and alloys. By using pulses of a duration in the range of 10 femtoseconds to 100 picoseconds, extremely precise machining can be achieved with essentially no heat or shock affected zone. Because the pulses are so short, there is negligible thermal conduction beyond the region removed resulting in negligible thermal stress or shock to the material beyond approximately 0.1-1 micron (dependent upon the particular material) from the laser machined surface. Due to the short duration, the high intensity (>10.sup.12 W/cm.sup.2) associated with the interaction converts the material directly from the solid-state into an ionized plasma. Hydrodynamic expansion of the plasma eliminates the need for any ancillary techniques to remove material and produces extremely high quality machined surfaces with negligible redeposition either within the kerf or on the surface. Since there is negligible heating beyond the depth of material removed, the composition of the remaining material is unaffected by the laser machining process. This enables high precision machining of alloys and even pure metals with no change in grain structure.

  9. Homopolar machine for reversible energy storage and transfer systems

    DOE Patents [OSTI]

    Stillwagon, Roy E.

    1978-01-01

    A homopolar machine designed to operate as a generator and motor in reversibly storing and transferring energy between the machine and a magnetic load coil for a thermo-nuclear reactor. The machine rotor comprises hollow thin-walled cylinders or sleeves which form the basis of the system by utilizing substantially all of the rotor mass as a conductor thus making it possible to transfer substantially all the rotor kinetic energy electrically to the load coil in a highly economical and efficient manner. The rotor is divided into multiple separate cylinders or sleeves of modular design, connected in series and arranged to rotate in opposite directions but maintain the supply of current in a single direction to the machine terminals. A stator concentrically disposed around the sleeves consists of a hollow cylinder having a number of excitation coils each located radially outward from the ends of adjacent sleeves. Current collected at an end of each sleeve by sleeve slip rings and brushes is transferred through terminals to the magnetic load coil. Thereafter, electrical energy returned from the coil then flows through the machine which causes the sleeves to motor up to the desired speed in preparation for repetition of the cycle. To eliminate drag on the rotor between current pulses, the brush rigging is designed to lift brushes from all slip rings in the machine.

  10. Homopolar machine for reversible energy storage and transfer systems

    DOE Patents [OSTI]

    Stillwagon, Roy E.

    1981-01-01

    A homopolar machine designed to operate as a generator and motor in reversibly storing and transferring energy between the machine and a magnetic load coil for a thermo-nuclear reactor. The machine rotor comprises hollow thin-walled cylinders or sleeves which form the basis of the system by utilizing substantially all of the rotor mass as a conductor thus making it possible to transfer substantially all the rotor kinetic energy electrically to the load coil in a highly economical and efficient manner. The rotor is divided into multiple separate cylinders or sleeves of modular design, connected in series and arranged to rotate in opposite directions but maintain the supply of current in a single direction to the machine terminals. A stator concentrically disposed around the sleeves consists of a hollow cylinder having a number of excitation coils each located radially outward from the ends of adjacent sleeves. Current collected at an end of each sleeve by sleeve slip rings and brushes is transferred through terminals to the magnetic load coil. Thereafter, electrical energy returned from the coil then flows through the machine which causes the sleeves to motor up to the desired speed in preparation for repetition of the cycle. To eliminate drag on the rotor between current pulses, the brush rigging is designed to lift brushes from all slip rings in the machine.

  11. Food Services | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Employee Services » Food Services Food Services The Department offers many food services for employees within the Headquarters' buildings. Forrestal Forrestal Cafeteria (2nd floor, West Building). See the Cafeteria web page for further information. Hours: Monday-Friday 6:45 a.m. to 3:00 p.m. Breakfast hours are from 6:45 a.m. until 10:00 a.m., lunch from 11:00 a.m. until 2:00 p.m., and a "Happy Hour" is featured from 2:00-2:30 p.m. offering 30% off all hot and cold buffet items. Other

  12. Whole Building Efficiency for Whole Foods: Preprint

    SciTech Connect (OSTI)

    Deru, M.; Doebber, I.; Hirsch, A.

    2013-02-01

    The National Renewable Energy Laboratory partnered with Whole Foods Market under the Commercial Building Partnership (CBP) program to design and implement a new store in Raleigh, North Carolina. The result was a design with a predicted energy savings of 40% over ASHRAE Standard 90.1-2004, and 25% energy savings over their standard design. Measured performance of the as-built building showed that the building did not achieve the predicted performance. A detailed review of the project several months after opening revealed a series of several items in construction and controls items that were not implemented properly and were not fully corrected in the commissioning process.

  13. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    EE, Food Service Equipment, Vending Machine Controls, Commercial Refrigeration Equipment Energy Optimization (Electric)- Commercial Efficiency Program Energy Optimization...

  14. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    pending approval, Other EE, Food Service Equipment, Vending Machine Controls, Personal Computing Equipment, LED Lighting, Tankless Water Heater, Commercial Refrigeration...

  15. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Whole Building, Other EE, Food Service Equipment, Vending Machine Controls, Personal Computing Equipment, Reflective Roofs, Commercial Refrigeration Equipment Business Energy...

  16. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    pending approval, Other EE, Food Service Equipment, Vending Machine Controls, Personal Computing Equipment, LED Lighting, Commercial Refrigeration Equipment Rocky Mountain...

  17. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Food Service Equipment, Vending Machine Controls, LED Lighting, Commercial Refrigeration Equipment Michigan Saves- Business Energy Financing Pre-qualification application...

  18. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    approval, Food Service Equipment, Vending Machine Controls, Commercial Refrigeration Equipment Michigan Saves- Business Energy Financing Pre-qualification application...

  19. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Food Service Equipment, Vending Machine Controls, Commercial Refrigeration Equipment Mora Municipal Utilities- Commercial & Industrial Energy Efficiency Rebate Program Southern...

  20. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Others pending approval, Other EE, Food Service Equipment, Vending Machine Controls, Data Center Equipment, Commercial Refrigeration Equipment Rochester Public Utilities-...

  1. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and Manufacturing Equipment, Comprehensive MeasuresWhole Building, Other EE, Food Service Equipment, Vending Machine Controls, Personal Computing Equipment, Reflective...

  2. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Equipment, CustomOthers pending approval, Other EE, Food Service Equipment, Vending Machine Controls, Commercial Refrigeration Equipment Longmont Power & Communications-...

  3. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Compressed air, Motors, Motor VFDs, Other EE, Food Service Equipment, Vending Machine Controls, Commercial Cooking Equipment, LED Lighting, Commercial Refrigeration...

  4. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Equipment, Agricultural Equipment, CustomOthers pending approval, Other EE, Food Service Equipment, Vending Machine Controls, LED Lighting, Commercial Refrigeration...

  5. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Equipment, Agricultural Equipment, CustomOthers pending approval, Other EE, Food Service Equipment, Vending Machine Controls, Personal Computing Equipment, LED...

  6. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Food Service Equipment, Vending Machine Controls, Personal Computing Equipment, Tankless Water Heater Energy Efficiency Investment Fund Rebates Specific efficiency requirements...

  7. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Food Service Equipment, Vending Machine Controls, Commercial Refrigeration Equipment Reading Municipal Light Department- Business Energy Efficiency Rebate Program Reading...

  8. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Equipment, Agricultural Equipment, CustomOthers pending approval, Other EE, Food Service Equipment, Vending Machine Controls, Personal Computing Equipment, Data...

  9. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    approval, Other EE, Food Service Equipment, Vending Machine Controls, Commercial Cooking Equipment, LED Lighting, Commercial Refrigeration Equipment PEPCO- Commercial and...

  10. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    approval, Other EE, Food Service Equipment, Vending Machine Controls, Commercial Cooking Equipment, LED Lighting, Commercial Refrigeration Equipment Renewable Energy and...

  11. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    approval, Other EE, Food Service Equipment, Vending Machine Controls, Commercial Cooking Equipment, LED Lighting, Commercial Refrigeration Equipment Multifamily Energy...

  12. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    approval, Other EE, Food Service Equipment, Vending Machine Controls, Commercial Cooking Equipment, LED Lighting, Commercial Refrigeration Equipment Enterprise Energy Fund...

  13. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    VFDs, Other EE, Food Service Equipment, Vending Machine Controls, LED Lighting Energy Optimization (Electric)- Commercial Efficiency Program Energy Optimization Eligibility:...

  14. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Other EE, Food Service Equipment, Vending Machine Controls, LED Lighting Energy Optimization (Electric)- Commercial Efficiency Program Energy Optimization Eligibility:...

  15. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Equipment, Agricultural Equipment, CustomOthers pending approval, Other EE, Food Service Equipment, Vending Machine Controls, Reflective Roofs, LED Lighting,...

  16. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    approval, Other EE, Food Service Equipment, Vending Machine Controls, Personal Computing Equipment, Data Center Equipment, LED Lighting, Commercial Refrigeration Equipment...

  17. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    EE, Food Service Equipment, Vending Machine Controls, Personal Computing Equipment, Data Center Equipment, LED Lighting, Tankless Water Heater, Commercial Refrigeration...

  18. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Food Service Equipment, Vending Machine Controls, Personal Computing Equipment, Data Center Equipment, Reflective Roofs, LED Lighting, Commercial Refrigeration Equipment Xcel...

  19. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Food Service Equipment, Vending Machine Controls, Personal Computing Equipment, Data Center Equipment, Reflective Roofs, LED Lighting, Commercial Refrigeration Equipment Alliant...

  20. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Food Service Equipment, Vending Machine Controls, Personal Computing Equipment, Data Center Equipment, LED Lighting, Tankless Water Heater, Commercial Refrigeration Equipment...

  1. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Building, CustomOthers pending approval, Other EE, Food Service Equipment, Vending Machine Controls, Personal Computing Equipment, Commercial Refrigeration Equipment...

  2. Biomass Boiler for Food Processing Applications | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Biomass Boiler for Food Processing Applications Biomass Boiler for Food Processing Applications Biomass Boiler Uses a Combination of Wood Waste and Tire-Derived Fuel In 2011, the ...

  3. Thanksgiving Goodwill: West Valley Demonstration Project Food...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Thanksgiving Goodwill: West Valley Demonstration Project Food Drive Provides 640 Turkeys to People in Need Thanksgiving Goodwill: West Valley Demonstration Project Food Drive...

  4. ISSUANCE 2015-10-20: Energy Conservation Program: Energy Conservation Standards for Refrigerated Beverage Vending Machines

    Broader source: Energy.gov [DOE]

    Energy Conservation Program: Energy Conservation Standards for Refrigerated Beverage Vending Machines

  5. The Kelastic variable wall mining machine. Interim final report

    SciTech Connect (OSTI)

    1995-11-12

    This machine cuts coal along a longwall face extending up to 500 feet by a rotating auger with bits. The machine also transports the coal that is cut acting as screw conveyor. By virtue of an integral shroud comprising part of the conveyor the machine is also amenable to a separation of the zones where men work from air being contaminated by dust and methane gas by the cutting action. Beginning as single intake air courses, the air separates at the working section where one split provides fresh air to the Occupied Zone (OZ) for human needs and the other split purges and carries away dust and methane from face fragmentation in the Cutting Zone (CZ). The attractiveness of the Variable Wall Mining Machine is that it addresses the limitations of current longwall mining equipment: it can consistently out-produce continuous mining machines and most longwall shearing machines. It also is amenable to configuring an environment, the dual-duct system, where the air for human breathing is separated from dust-laden ventilating air with methane mixtures. The objective of the research was to perform a mathematical and experimental study of the interrelationships of the components of the system so that a computer model could demonstrate the workings of the system in an animation program. The analysis resulted in the compilation of the parameters for three different configurations of a dual aircourse system of ventilating underground mines. In addressing the goal of an inherently safe mining system the dual-duct adaptation to the Variable Wall Mining Machine appears to offer the path to solution. The respirable dust problem is solvable; the explosive dust problem is nearly solvable; and the explosive methane problem can be greatly reduced. If installed in a highly gassy mine, the dual duct models would also be considerably less costly.

  6. Automated manual transmission controller

    DOE Patents [OSTI]

    Lawrie, Robert E.; Reed, Jr., Richard G.; Bernier, David R.

    1999-12-28

    A powertrain system for a hybrid vehicle. The hybrid vehicle includes a heat engine, such as a diesel engine, and an electric machine, which operates as both an electric motor and an alternator, to power the vehicle. The hybrid vehicle also includes a manual-style transmission configured to operate as an automatic transmission from the perspective of the driver. The engine and the electric machine drive an input shaft which in turn drives an output shaft of the transmission. In addition to driving the transmission, the electric machine regulates the speed of the input shaft in order to synchronize the input shaft during either an upshift or downshift of the transmission by either decreasing or increasing the speed of the input shaft. When decreasing the speed of the input shaft, the electric motor functions as an alternator to produce electrical energy which may be stored by a storage device. Operation of the transmission is controlled by a transmission controller which receives input signals and generates output signals to control shift and clutch motors to effect smooth launch, upshift shifts, and downshifts of the transmission, so that the transmission functions substantially as an automatic transmission from the perspective of the driver, while internally substantially functioning as a manual transmission.

  7. PWM Inverter control and the application thereof within electric vehicles

    DOE Patents [OSTI]

    Geppert, Steven

    1982-01-01

    An inverter (34) which provides power to an A.C. machine (28) is controlled by a circuit (36) employing PWM control strategy whereby A.C. power is supplied to the machine at a preselectable frequency and preselectable voltage. This is accomplished by the technique of waveform notching in which the shapes of the notches are varied to determine the average energy content of the overall waveform. Through this arrangement, the operational efficiency of the A.C. machine is optimized. The control circuit includes a micro-computer and memory element which receive various parametric inputs and calculate optimized machine control data signals therefrom. The control data is asynchronously loaded into the inverter through an intermediate buffer (38). In its preferred embodiment, the present invention is incorporated within an electric vehicle (10) employing a 144 VDC battery pack (32) and a three-phase induction motor (18).

  8. Holographic Labeling And Reading Machine For Authentication And Security Appications

    DOE Patents [OSTI]

    Weber, David C.; Trolinger, James D.

    1999-07-06

    A holographic security label and automated reading machine for marking and subsequently authenticating any object such as an identification badge, a pass, a ticket, a manufactured part, or a package is described. The security label is extremely difficult to copy or even to read by unauthorized persons. The system comprises a holographic security label that has been created with a coded reference wave, whose specification can be kept secret. The label contains information that can be extracted only with the coded reference wave, which is derived from a holographic key, which restricts access of the information to only the possessor of the key. A reading machine accesses the information contained in the label and compares it with data stored in the machine through the application of a joint transform correlator, which is also equipped with a reference hologram that adds additional security to the procedure.

  9. Method for producing hard-surfaced tools and machine components

    DOE Patents [OSTI]

    McHargue, Carl J.

    1985-01-01

    In one aspect, the invention comprises a method for producing tools and machine components having superhard crystalline-ceramic work surfaces. Broadly, the method comprises two steps: A tool or machine component having a ceramic near-surface region is mounted in ion-implantation apparatus. The region then is implanted with metal ions to form, in the region, a metastable alloy of the ions and said ceramic. The region containing the alloy is characterized by a significant increase in hardness properties, such as microhardness, fracture-toughness, and/or scratch-resistance. The resulting improved article has good thermal stability at temperatures characteristic of typical tool and machine-component uses. The method is relatively simple and reproducible.

  10. Novel Transverse Flux Machine for Vehicle Traction Applications: Preprint

    SciTech Connect (OSTI)

    Wan, Z.; Ahmed, A.; Husain, I.; Muljadi, E.

    2015-04-02

    A novel transverse flux machine topology for electric vehicle traction applications using ferrite magnets is presented in this paper. The proposed transverse flux topology utilizes novel magnet arrangements in the rotor that are similar to the Halbach array to boost flux linkage; on the stator side, cores are alternately arranged around a pair of ring windings in each phase to make use of the entire rotor flux that eliminates end windings. Analytical design considerations and finite-element methods are used for an optimized design of a scooter in-wheel motor. Simulation results from finite element analysis (FEA) show that the motor achieved comparable torque density to conventional rare-earth permanent magnet (PM) machines. This machine is a viable candidate for direct-drive applications with low cost and high torque density.

  11. Method for producing hard-surfaced tools and machine components

    DOE Patents [OSTI]

    McHargue, C.J.

    1981-10-21

    In one aspect, the invention comprises a method for producing tools and machine components having superhard crystalline-ceramic work surfaces. Broadly, the method comprises two steps: a tool or machine component having a ceramic near-surface region is mounted in ion-implantation apparatus. The region then is implanted with metal ions to form, in the region, a metastable alloy of the ions and said ceramic. The region containing the alloy is characterized by a significant increase in hardness properties, such as microhardness, fracture-toughness, and/or scratch-resistance. The resulting improved article has good thermal stability at temperatures characteristic of typical tool and machine-component uses. The method is relatively simple and reproducible.

  12. SU-E-T-373: A Motorized Stage for Fast and Accurate QA of Machine Isocenter

    SciTech Connect (OSTI)

    Moore, J; Velarde, E; Wong, J

    2014-06-01

    Purpose: Precision delivery of radiation dose relies on accurate knowledge of the machine isocenter under a variety of machine motions. This is typically determined by performing a Winston-Lutz test consisting of imaging a known object at multiple gantry/collimator/table angles and ensuring that the maximum offset is within specified tolerance. The first step in the Winston-Lutz test is careful placement of a ball bearing at the machine isocenter as determined by repeated imaging and shifting until accurate placement has been determined. Conventionally this is performed by adjusting a stage manually using vernier scales which carry the limitation that each adjustment must be done inside the treatment room with the risks of inaccurate adjustment of the scale and physical bumping of the table. It is proposed to use a motorized system controlled outside of the room to improve the required time and accuracy of these tests. Methods: The three dimensional vernier scales are replaced by three motors with accuracy of 1 micron and a range of 25.4mm connected via USB to a computer in the control room. Software is designed which automatically detects the motors and assigns them to proper axes and allows for small shifts to be entered and performed. Input values match calculated offsets in magnitude and sign to reduce conversion errors. Speed of setup, number of iterations to setup, and accuracy of final placement are assessed. Results: Automatic BB placement required 2.25 iterations and 13 minutes on average while manual placement required 3.76 iterations and 37.5 minutes. The average final XYZ offsets is 0.02cm, 0.01cm, 0.04cm for automatic setup and 0.04cm, 0.02cm, 0.04cm for manual setup. Conclusion: Automatic placement decreased time and repeat iterations for setup while improving placement accuracy. Automatic placement greatly reduces the time required to perform QA.

  13. Intense x-ray machine for penetrating radiography

    SciTech Connect (OSTI)

    Lucht, R.A.; Eckhouse, S.

    1989-01-01

    Penetrating radiography has been used for many years in the nuclear weapons research programs. In frequently penetrating radiography has been used in conventional weapons research programs. For example the Los Alamos PHERMEX machine was used to view uranium rods penetrating steel for the GAU-8 program, and the Ector machine was used to see low-density regions in forming metal jets. The armor/anti-armor program at Los Alamos has created a need for an intense flash x-ray machine that can be dedicated to conventional weapons research. The Balanced Technology Initiative, through DARPA, has funded the design and construction of such a machine at Los Alamos. It will be an 8- to 10-MeV diode machine capable of delivering a dose of 500 R at 1 m with a spot size of less than 5 mm. The machine used an 87.5-stage low-inductance Marx generator that charges up a 7.4-/Omega/, 32-ns water line. The water line is discharged through a self-breakdown oil switch into a 12.4-/Omega/ water line that rings up the voltage into the high-impendance x-ray diode. A long (233-cm) vacuum drift tube is used to separate the large-diameter oil-insulated diode region from the x-ray source area that may be exposed to high overpressures by the explosive experiments. The electron beam is self-focused at the target area using a low-pressure background gas. 15 refs., 11 figs.

  14. Superconducting PM undiffused machines with stationary superconducting coils

    DOE Patents [OSTI]

    Hsu, John S.; Schwenterly, S. William

    2004-03-02

    A superconducting PM machine has a stator, a rotor and a stationary excitation source without the need of a ferromagnetic frame which is cryogenically cooled for operation in the superconducting state. PM material is placed between poles on the rotor to prevent leakage or diffusion of secondary flux before reaching the main air gap, or to divert PM flux where it is desired to weaken flux in the main air gap. The PM material provides hop-along capability for the machine in the event of a fault condition.

  15. 20140501-0531_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Thibedeau, Joe

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 01 May to 31 May 2014.

  16. 20140101-0131_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Thibedeau, Joe

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 01 Jan to 31 Jan 2014.

  17. 20130501-20130531_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Vanderhoff, Alex

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from May 2013

  18. 20130901-0930_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Thibedeau, Joe

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 1 September 2013 to 30 September 2013.

  19. 20131001-1031_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Thibedeau, Joe

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 1 Oct 2013 to 31 Oct 2013.

  20. 20140301-0331_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Thibedeau, Joe

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 01 Mar to 31 Mar 2014.

  1. 20131201-1231_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Thibedeau, Joe

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 01 Dec to 31 Dec 2013.

  2. 20140701-0731_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Thibedeau, Joe

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 01 July to 31 July 2014.

  3. 20130801-0831_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Vanderhoff, Alex

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 8/1/13 to 8/31/13.

  4. 20140201-0228_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Thibedeau, Joe

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 01 Feb to 28 Feb 2014.

  5. 20140601-0630_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Thibedeau, Joe

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 01 June to 30 June 2014.

  6. 20131101-1130_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Thibedeau, Joe

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 01 Nov to 30 Nov 2013.

  7. Fermilab | Directorate | PIP-II Machine Advisory Committee (XMAC)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    PIP-II Machine Advisory Committee (P2MAC) Meeting of the Fermilab PIP-II Advisory Committee March 9-11, 2015 2014 Recommendations Response 2014 XMAC Report P2MAC Charge PIP-II Website Agenda Final Report Fermilab PIP-II Machine Advisory Committee Roland Garoby, Chair (ESS, Sweden) Frank Gerigk (CERN) Kazuo Hasegawa (J-PARC, Japan) Deepak Raparia (Brookhaven National Laboratory) Rick Baartman (TRIUMF, Canada) Jie Wei (Michigan State University) Hans Weise (DESY, Germany) Sang-ho Kim (Oak Ridge

  8. 20130801-0831_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Vanderhoff, Alex

    2013-09-10

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 8/1/13 to 8/31/13.

  9. 20140601-0630_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Thibedeau, Joe

    2014-06-30

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 01 June to 30 June 2014.

  10. 20131201-1231_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Thibedeau, Joe

    2014-01-08

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 01 Dec to 31 Dec 2013.

  11. 20140701-0731_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Thibedeau, Joe

    2014-07-31

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 01 July to 31 July 2014.

  12. 20140201-0228_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Thibedeau, Joe

    2014-03-03

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 01 Feb to 28 Feb 2014.

  13. 20130501-20130531_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Vanderhoff, Alex

    2013-06-18

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from May 2013

  14. 20140301-0331_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Thibedeau, Joe

    2014-04-07

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 01 Mar to 31 Mar 2014.

  15. 20130901-0930_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Thibedeau, Joe

    2013-10-25

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 1 September 2013 to 30 September 2013.

  16. 20131101-1130_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Thibedeau, Joe

    2013-12-02

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 01 Nov to 30 Nov 2013.

  17. 20131001-1031_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Thibedeau, Joe

    2013-11-05

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 1 Oct 2013 to 31 Oct 2013.

  18. 20140501-0531_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Thibedeau, Joe

    2014-06-02

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 01 May to 31 May 2014.

  19. 20140101-0131_Green Machine Florida Canyon Hourly Data

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Thibedeau, Joe

    2014-02-03

    Employing innovative product developments to demonstrate financial and technical viability of producing electricity from low temperature geothermal fluids, coproduced in a mining operation, by employing ElectraTherm's modular and mobile heat-to-power "micro geothermal" power plant with output capacity expected in the 30-70kWe range. The Green Machine is an Organic Rankine Cycle power plant. The Florida Canyon machine is powered by geothermal brine with air cooled condensing. The data provided is an hourly summary from 01 Jan to 31 Jan 2014.

  20. Control system for supercharged internal combustion engine

    SciTech Connect (OSTI)

    Kawamura, H.

    1988-05-24

    A control system for controlling an internal combustion engine is described having a supercharge including a rotatable shaft and an exhaust turbine driven by exhaust gas. The control system comprising: a rotary electric machine mounted on the rotatable shaft of the supercharger for imposing a load on the exhaust turbine of the supercharger; setting means for setting an engine brake mode of the internal combustion engine; and operating means for operating the rotary electric machine when the engine brake mode is set by the setting means.

  1. Emulating a million machines to investigate botnets.

    SciTech Connect (OSTI)

    Rudish, Donald W.

    2010-06-01

    Researchers at Sandia National Laboratories in Livermore, California are creating what is in effect a vast digital petridish able to hold one million operating systems at once in an effort to study the behavior of rogue programs known as botnets. Botnets are used extensively by malicious computer hackers to steal computing power fron Internet-connected computers. The hackers harness the stolen resources into a scattered but powerful computer that can be used to send spam, execute phishing, scams or steal digital information. These remote-controlled 'distributed computers' are difficult to observe and track. Botnets may take over parts of tens of thousands or in some cases even millions of computers, making them among the world's most powerful computers for some applications.

  2. Micro rotary machine and methods for using same

    SciTech Connect (OSTI)

    Stalford, Harold

    2015-01-13

    A micro rotary machine may include a micro actuator and a micro shaft coupled to the micro actuator. The micro shaft comprises a horizontal shaft and is operable to be rotated by the micro actuator. A micro tool is coupled to the micro shaft and is operable to perform work in response to motion of the micro shaft.

  3. Purchasing Energy-Efficient Air-Cooled Ice Machines

    Broader source: Energy.gov [DOE]

    The Federal Energy Management Program (FEMP) provides acquisition guidance for air-cooled ice machines, a product category covered by ENERGY STAR efficiency requirements. Federal laws and requirements mandate that agencies purchase ENERGY STAR-qualified products or FEMP-designated products in all product categories covered by these programs and in any acquisition actions that are not specifically exempted by law.

  4. Purchasing Energy-Efficient Refrigerated Beverage Vending Machines

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance and Federal efficiency requirements across a variety of product categories, including refrigerated beverage vending machines, which are covered by the ENERGY STAR® program. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

  5. Fracture mechanics applied to the machining of brittle materials

    SciTech Connect (OSTI)

    Hiatt, G.D.; Strenkowski, J.S.

    1988-12-01

    Research has begun on incorporating fracture mechanics into a model of the orthogonal cutting of brittle materials. Residual stresses are calculated for the machined material by a combination of Eulerian and Lagrangian finite element models and then used in the calculation of stress intensity factors by the Green`s Function Method.

  6. Micro rotary machine and methods for using same

    DOE Patents [OSTI]

    Stalford, Harold L.

    2012-04-17

    A micro rotary machine may include a micro actuator and a micro shaft coupled to the micro actuator. The micro shaft comprises a horizontal shaft and is operable to be rotated by the micro actuator. A micro tool is coupled to the micro shaft and is operable to perform work in response to motion of the micro shaft.

  7. Data flow machine for data driven computing

    DOE Patents [OSTI]

    Davidson, George S.; Grafe, Victor G.

    1995-01-01

    A data flow computer which of computing is disclosed which utilizes a data driven processor node architecture. The apparatus in a preferred embodiment includes a plurality of First-In-First-Out (FIFO) registers, a plurality of related data flow memories, and a processor. The processor makes the necessary calculations and includes a control unit to generate signals to enable the appropriate FIFO register receiving the result. In a particular embodiment, there are three FIFO registers per node: an input FIFO register to receive input information form an outside source and provide it to the data flow memories; an output FIFO register to provide output information from the processor to an outside recipient; and an internal FIFO register to provide information from the processor back to the data flow memories. The data flow memories are comprised of four commonly addressed memories. A parameter memory holds the A and B parameters used in the calculations; an opcode memory holds the instruction; a target memory holds the output address; and a tag memory contains status bits for each parameter. One status bit indicates whether the corresponding parameter is in the parameter memory and one status but to indicate whether the stored information in the corresponding data parameter is to be reused. The tag memory outputs a "fire" signal (signal R VALID) when all of the necessary information has been stored in the data flow memories, and thus when the instruction is ready to be fired to the processor.

  8. Data flow machine for data driven computing

    DOE Patents [OSTI]

    Davidson, G.S.; Grafe, V.G.

    1988-07-22

    A data flow computer and method of computing is disclosed which utilizes a data driven processor node architecture. The apparatus in a preferred embodiment includes a plurality of First-In-First-Out (FIFO) registers, a plurality of related data flow memories, and a processor. The processor makes the necessary calculations and includes a control unit to generate signals to enable the appropriate FIFO register receiving the result. In a particular embodiment, there are three FIFO registers per node: an input FIFO register to receive input information from an outside source and provide it to the data flow memories; an output FIFO register to provide output information from the processor to an outside recipient; and an internal FIFO register to provide information from the processor back to the data flow memories. The data flow memories are comprised of four commonly addressed memories. A parameter memory holds the A and B parameters used in the calculations; an opcode memory holds the instruction; a target memory holds the output address; and a tag memory contains status bits for each parameter. One status bit indicates whether the corresponding parameter is in the parameter memory and one status bit to indicate whether the stored information in the corresponding data parameter is to be reused. The tag memory outputs a ''fire'' signal (signal R VALID) when all of the necessary information has been stored in the data flow memories, and thus when the instruction is ready to be fired to the processor. 11 figs.

  9. Data flow machine for data driven computing

    SciTech Connect (OSTI)

    Davidson, G.S.; Grafe, V.G.

    1995-11-07

    A data flow computer is disclosed which utilizes a data driven processor node architecture. The apparatus in a preferred embodiment includes a plurality of First-In-First-Out (FIFO) registers, a plurality of related data flow memories, and a processor. The processor makes the necessary calculations and includes a control unit to generate signals to enable the appropriate FIFO register receiving the result. In a particular embodiment, there are three FIFO registers per node: an input FIFO register to receive input information form an outside source and provide it to the data flow memories; an output FIFO register to provide output information from the processor to an outside recipient; and an internal FIFO register to provide information from the processor back to the data flow memories. The data flow memories are comprised of four commonly addressed memories. A parameter memory holds the A and B parameters used in the calculations; an opcode memory holds the instruction; a target memory holds the output address; and a tag memory contains status bits for each parameter. One status bit indicates whether the corresponding parameter is in the parameter memory and one status but to indicate whether the stored information in the corresponding data parameter is to be reused. The tag memory outputs a ``fire`` signal (signal R VALID) when all of the necessary information has been stored in the data flow memories, and thus when the instruction is ready to be fired to the processor. 11 figs.

  10. Quench monitoring and control system and method of operating same

    DOE Patents [OSTI]

    Ryan, David Thomas; Laskaris, Evangelos Trifon; Huang, Xianrui

    2006-05-30

    A rotating machine comprising a superconductive coil and a temperature sensor operable to provide a signal representative of superconductive coil temperature. The rotating machine may comprise a control system communicatively coupled to the temperature sensor. The control system may be operable to reduce electric current in the superconductive coil when a signal representative of a defined superconducting coil temperature is received from the temperature sensor.

  11. FEMA and RAM Analysis for the Multi Canister Overpack (MCO) Handling Machine

    SciTech Connect (OSTI)

    SWENSON, C.E.

    2000-06-01

    The Failure Modes and Effects Analysis and the Reliability, Availability, and Maintainability Analysis performed for the Multi-Canister Overpack Handling Machine (MHM) has shown that the current design provides for a safe system, but the reliability of the system (primarily due to the complexity of the interlocks and permissive controls) is relatively low. No specific failure modes were identified where significant consequences to the public occurred, or where significant impact to nearby workers should be expected. The overall reliability calculation for the MHM shows a 98.1 percent probability of operating for eight hours without failure, and an availability of the MHM of 90 percent. The majority of the reliability issues are found in the interlocks and controls. The availability of appropriate spare parts and maintenance personnel, coupled with well written operating procedures, will play a more important role in successful mission completion for the MHM than other less complicated systems.

  12. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Lighting ControlsSensors, Energy Mgmt. SystemsBuilding Controls, Motors, Other EE, Food Service Equipment, Vending Machine Controls, LED Lighting, Tankless Water Heater,...

  13. Method and apparatus for controlling a powertrain system including a multi-mode transmission

    SciTech Connect (OSTI)

    Hessell, Steven M.; Morris, Robert L.; McGrogan, Sean W.; Heap, Anthony H.; Mendoza, Gil J.

    2015-09-08

    A powertrain including an engine and torque machines is configured to transfer torque through a multi-mode transmission to an output member. A method for controlling the powertrain includes employing a closed-loop speed control system to control torque commands for the torque machines in response to a desired input speed. Upon approaching a power limit of a power storage device transferring power to the torque machines, power limited torque commands are determined for the torque machines in response to the power limit and the closed-loop speed control system is employed to determine an engine torque command in response to the desired input speed and the power limited torque commands for the torque machines.

  14. Method and apparatus for characterizing and enhancing the dynamic performance of machine tools

    DOE Patents [OSTI]

    Barkman, William E; Babelay, Jr., Edwin F

    2013-12-17

    Disclosed are various systems and methods for assessing and improving the capability of a machine tool. The disclosure applies to machine tools having at least one slide configured to move along a motion axis. Various patterns of dynamic excitation commands are employed to drive the one or more slides, typically involving repetitive short distance displacements. A quantification of a measurable merit of machine tool response to the one or more patterns of dynamic excitation commands is typically derived for the machine tool. Examples of measurable merits of machine tool performance include dynamic one axis positional accuracy of the machine tool, dynamic cross-axis stability of the machine tool, and dynamic multi-axis positional accuracy of the machine tool.

  15. Y-12 continues to push the state-of-the-art in machining - Or...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    continues to push the state-of-the-art in machining - Or: Machining technology helped give U.S. edge during Cold War (title used in The Oak Ridger) The decade of the 1960"s brought...

  16. Jack Case ? the man who helped bring uranium machining to Y...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    the man who helped bring uranium machining to Y-12 Most of you realize that Y-12 is basically a huge and very precise machine shop. For years it has been the nation's only uranium...

  17. Employees give to local food bank

    Broader source: Energy.gov [DOE]

    Employees in DOE's Oak Ridge Office of EM donated 3,209 pounds of food to the Second Harvest Food Bank of East Tennessee. The donation was part of the national Feds Feed Families campaign.

  18. Bioenergy Impacts Â… Non-Food

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    the cost of producing biofuel from non-food sources (such as corn stalks, grasses, and ... Biofuel from non-food sources is becoming cheaper to produce BIOENERGY IMPACTS To learn ...

  19. Microsoft PowerPoint - Machine Learning with User Intelligence [Compatibility Mode]

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    1872 This document is approved for public release; further dissemination unlimited Machine Learning with User Intelligence Machine Learning with User Intelligence Automated data analysis tools are unable to bridge the semantic gap between complex data and critical information. Advancing the Training Dialog and the Training Vocabulary moves machine learning into end-user environments Our advances in machine learning theory and algorithms can benefit a wide range of applications. * Interactive

  20. On-machine sensors to measure paper mechanical properties. Final report

    SciTech Connect (OSTI)

    Hall, M.S.; Brodeur, P.H.; Jackson, T.G.

    1993-10-01

    The measurement of the velocity of ultrasound provides a nondestructive means to characterize the elastic stiffness properties of paper. The objective of this project is to develop sensors capable of measuring the velocity of ultrasound in the thickness and in-plane directions of moving paper webs. On-machine measurements would allow continuous monitoring of product quality as well as provide data for controlling the papermaking process. This final report first reviews the background and various technical approaches explored. Then the preferred configurations and examples of measurements on moving paper webs in the laboratory are presented and discussed. The report concludes with a summary of project results and recommendations for further developments. Transducers mounted in fluid-filled wheels are used to make thickness direction, ZD, ultrasound velocity measurements on paper webs moving in the nip between two such wheels. Comparisons of the arrival times of echo and transmitted pulses with and without the paper web in the nip provide a measure of the transit time and caliper. Bimorph transducers mounted in an aluminum cylinder are used for machine direction (MD) and cross direction (CD) in-plane measurements. These ZD and in-plane sensors are mounted on a web handler in the IPST laboratory.

  1. THERMAL STUDY OF THE DIII-D MACHINE HEAT REMOVAL CAPACITY

    SciTech Connect (OSTI)

    YIP,H; ADERSON,P.M; HOLTROP,K.L; HARRISON,S

    2003-10-01

    OAK-B135 With each plasma shot, the DIII-D tokamak dissipates 0.5 to 1.0 GJ of energy. Plasma shots may occur as frequently as every ten minutes, and the energy is removed in the form of heat by a cooling water system. to remove heat from the machine, cooling water circulates through each major heat source. These sources include the power supplies, motor/generator, rf current drives, neutral beam power supplies, magnetic field coils, and vacuum vessel. The cooling water system consists of isolated primary and secondary cooling loops separated by intermediate heat exchangers. As future DIII-D plans include operation during summer months and longer pulse duration, the cooling system's overall heat removal capability and performance efficiency must be assessed. Temperature and flow data from around the DIII-D facility are collected by a programmable logic controller (PLC); the data are used to analyze the heat generating sources, the heat transfer rate to intermediate heat exchangers, and the ultimate heat rejection to the environment via the cooling towers. A comparison of the original DIII-D machine design versus the actual performance determines the margin of heat removal capacity. projections of the heat removal rate for various longer plasma shots are made. Improvements in design and/or operational procedure will be necessary to attain the desired pulse duration.

  2. POLYSHIFT Communications Software for the Connection Machine System CM-200

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    George, William; Brickner, Ralph G.; Johnsson, S. Lennart

    1994-01-01

    We describe the use and implementation of a polyshift function PSHIFT for circular shifts and end-offs shifts. Polyshift is useful in many scientific codes using regular grids, such as finite difference codes in several dimensions, and multigrid codes, molecular dynamics computations, and in lattice gauge physics computations, such as quantum chromodynamics (QCD) calculations. Our implementation of the PSHIFT function on the Connection Machine systems CM-2 and CM-200 offers a speedup of up to a factor of 3–4 compared with CSHIFT when the local data motion within a node is small. The PSHIFT routine is included in the Connection Machine Scientificmore » Software Library (CMSSL).« less

  3. Machine learning strategies for systems with invariance properties

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Ling, Julia; Jones, Reese E.; Templeton, Jeremy Alan

    2016-05-06

    Here, in many scientific fields, empirical models are employed to facilitate computational simulations of engineering systems. For example, in fluid mechanics, empirical Reynolds stress closures enable computationally-efficient Reynolds-Averaged Navier-Stokes simulations. Likewise, in solid mechanics, constitutive relations between the stress and strain in a material are required in deformation analysis. Traditional methods for developing and tuning empirical models usually combine physical intuition with simple regression techniques on limited data sets. The rise of high-performance computing has led to a growing availability of high-fidelity simulation data, which open up the possibility of using machine learning algorithms, such as random forests or neuralmore » networks, to develop more accurate and general empirical models. A key question when using data-driven algorithms to develop these models is how domain knowledge should be incorporated into the machine learning process. This paper will specifically address physical systems that possess symmetry or invariance properties. Two different methods for teaching a machine learning model an invariance property are compared. In the first , a basis of invariant inputs is constructed, and the machine learning model is trained upon this basis, thereby embedding the invariance into the model. In the second method, the algorithm is trained on multiple transformations of the raw input data until the model learns invariance to that transformation. Results are discussed for two case studies: one in turbulence modeling and one in crystal elasticity. It is shown that in both cases embedding the invariance property into the input features yields higher performance with significantly reduced computational training costs.« less

  4. Diamond tool machining of materials which react with diamond

    DOE Patents [OSTI]

    Lundin, Ralph L.; Stewart, Delbert D.; Evans, Christopher J.

    1992-01-01

    Apparatus for the diamond machining of materials which detrimentally react with diamond cutting tools in which the cutting tool and the workpiece are chilled to very low temperatures. This chilling halts or retards the chemical reaction between the workpiece and the diamond cutting tool so that wear rates of the diamond tool on previously detrimental materials are comparable with the diamond turning of materials which do not react with diamond.

  5. Diamond tool machining of materials which react with diamond

    DOE Patents [OSTI]

    Lundin, R.L.; Stewart, D.D.; Evans, C.J.

    1992-04-14

    An apparatus is described for the diamond machining of materials which detrimentally react with diamond cutting tools in which the cutting tool and the workpiece are chilled to very low temperatures. This chilling halts or retards the chemical reaction between the workpiece and the diamond cutting tool so that wear rates of the diamond tool on previously detrimental materials are comparable with the diamond turning of materials which do not react with diamond. 1 figs.

  6. Fault Detection Tool Project: Automatic Discovery of Faults using Machine

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Learning Fault Detection Tool Project: Automatic Discovery of Faults using Machine Learning - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization

  7. power electronics and machines | netl.doe.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Advanced Power Electronics and Electrical Machines Improvements in electric traction drives are essential to electric drive vehicles, and have the potential to significantly reduce petroleum consumption in the transportation sector as well as help meet national economic and energy security goals. Hybrid electric vehicles (HEVs) can reduce petroleum use compared to average conventional vehicles by as much as 50%, while plug-in electric vehicles (PEVs) extend these savings even further. Advanced

  8. A Novel Transverse Flux Machine for Vehicle Traction Applications: Preprint

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    A Novel Transverse Flux Machine for Vehicle Traction Applications Preprint Z. Wan, A. Ahmed, and I. Husain North Carolina State University E. Muljadi National Renewable Energy Laboratory To be presented at the 2015 IEEE Power and Energy Society General Meeting Denver, Colorado July 26-30, 2015 Conference Paper NREL/CP-5D00-63661 April 2015 NOTICE The submitted manuscript has been offered by an employee of the Alliance for Sustainable Energy, LLC (Alliance), a contractor of the US Government

  9. Remembering the long day's journey to a historic machine's Christmas

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Eve first plasma | Princeton Plasma Physics Lab Remembering the long day's journey to a historic machine's Christmas Eve first plasma By John Greenwald December 21, 2012 Tweet Widget Google Plus One Share on Facebook The big moment arrives: The successful first plasma brought cheers to the command center. (Photo by Princeton Plasma Physics Laboratory) The big moment arrives: The successful first plasma brought cheers to the command center. 'Twas the night before Christmas and all through the

  10. Permanent magnet machine with windings having strand transposition

    DOE Patents [OSTI]

    Qu, Ronghai; Jansen, Patrick Lee

    2009-04-21

    This document discusses, among other things, a stator with transposition between the windings or coils. The coils are free from transposition to increase the fill factor of the stator slots. The transposition at the end connections between an inner coil and an outer coil provide transposition to reduce circulating current loss. The increased fill factor reduces further current losses. Such a stator is used in a dual rotor, permanent magnet machine, for example, in a compressor pump, wind turbine gearbox, wind turbine rotor.

  11. Radiator debris removing apparatus and work machine using same

    DOE Patents [OSTI]

    Martin, Kevin L. (Washburn, IL); Elliott, Dwight E. (Chillicothe, IL)

    2008-09-02

    A radiator assembly includes a finned radiator core and a debris removing apparatus having a compressed air inlet and at least one compressed air outlet configured to direct compressed air through the radiator core. A work machine such as a wheel loader includes a radiator and a debris removing apparatus coupled with on-board compressed air and having at least one pressurized gas outlet configured to direct a gas toward the face of the radiator.

  12. Classifier based on support vector machine for JET plasma configurations

    SciTech Connect (OSTI)

    Dormido-Canto, S.; Farias, G.; Dormido, R.; Sanchez, J.; Duro, N.; Vargas, H.

    2008-10-15

    The last flux surface can be used to identify the plasma configuration of discharges. For automated recognition of JET configurations, a learning system based on support vector machines has been developed. Each configuration is described by 12 geometrical parameters. A multiclass system has been developed by means of the one-versus-the-rest approach. Results with eight simultaneous classes (plasma configurations) show a success rate close to 100%.

  13. Advanced Power Electronics and Electric Machines | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    09 DOE Hydrogen Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting, May 18-22, 2009 -- Washington D.C. PDF icon ape_0_rogers.pdf More Documents & Publications Advnaced Power Electronics and Electric Machines (APEEM) R&D Program Overview Advanced Power Electronics and Electric Motors (APEEM) R&D Program Overview Advanced Power Electronics and Electric Motors R&D

  14. Machine learning strategies for systems with invariance properties

    SciTech Connect (OSTI)

    Ling, Julia; Jones, Reese E.; Templeton, Jeremy Alan

    2016-01-01

    Here, in many scientific fields, empirical models are employed to facilitate computational simulations of engineering systems. For example, in fluid mechanics, empirical Reynolds stress closures enable computationally-efficient Reynolds-Averaged Navier-Stokes simulations. Likewise, in solid mechanics, constitutive relations between the stress and strain in a material are required in deformation analysis. Traditional methods for developing and tuning empirical models usually combine physical intuition with simple regression techniques on limited data sets. The rise of high-performance computing has led to a growing availability of high-fidelity simulation data, which open up the possibility of using machine learning algorithms, such as random forests or neural networks, to develop more accurate and general empirical models. A key question when using data-driven algorithms to develop these models is how domain knowledge should be incorporated into the machine learning process. This paper will specifically address physical systems that possess symmetry or invariance properties. Two different methods for teaching a machine learning model an invariance property are compared. In the first , a basis of invariant inputs is constructed, and the machine learning model is trained upon this basis, thereby embedding the invariance into the model. In the second method, the algorithm is trained on multiple transformations of the raw input data until the model learns invariance to that transformation. Results are discussed for two case studies: one in turbulence modeling and one in crystal elasticity. It is shown that in both cases embedding the invariance property into the input features yields higher performance with significantly reduced computational training costs.

  15. Coordinated joint motion control system with position error correction

    DOE Patents [OSTI]

    Danko, George L.

    2016-04-05

    Disclosed are an articulated hydraulic machine supporting, control system and control method for same. The articulated hydraulic machine has an end effector for performing useful work. The control system is capable of controlling the end effector for automated movement along a preselected trajectory. The control system has a position error correction system to correct discrepancies between an actual end effector trajectory and a desired end effector trajectory. The correction system can employ one or more absolute position signals provided by one or more acceleration sensors supported by one or more movable machine elements. Good trajectory positioning and repeatability can be obtained. A two joystick controller system is enabled, which can in some cases facilitate the operator's task and enhance their work quality and productivity.

  16. Coordinated joint motion control system with position error correction

    DOE Patents [OSTI]

    Danko, George

    2011-11-22

    Disclosed are an articulated hydraulic machine supporting, control system and control method for same. The articulated hydraulic machine has an end effector for performing useful work. The control system is capable of controlling the end effector for automated movement along a preselected trajectory. The control system has a position error correction system to correct discrepancies between an actual end effector trajectory and a desired end effector trajectory. The correction system can employ one or more absolute position signals provided by one or more acceleration sensors supported by one or more movable machine elements. Good trajectory positioning and repeatability can be obtained. A two-joystick controller system is enabled, which can in some cases facilitate the operator's task and enhance their work quality and productivity.

  17. Coordinate measuring machine test standard apparatus and method

    DOE Patents [OSTI]

    Bieg, Lothar F.

    1994-08-30

    A coordinate measuring machine test standard apparatus and method which iudes a rotary spindle having an upper phase plate and an axis of rotation, a kinematic ball mount attached to the phase plate concentric with the axis of rotation of the phase plate, a groove mounted at the circumference of the phase plate, and an arm assembly which rests in the groove. The arm assembly has a small sphere at one end and a large sphere at the other end. The small sphere may be a coordinate measuring machine probe tip and may have variable diameters. The large sphere is secured in the kinematic ball mount and the arm is held in the groove. The kinematic ball mount includes at least three mounting spheres and the groove is an angular locating groove including at least two locking spheres. The arm may have a hollow inner core and an outer layer. The rotary spindle may be a ratio reducer. The device is used to evaluate the measuring performance of a coordinate measuring machine for periodic recertification, including 2 and 3 dimensional accuracy, squareness, straightness, and angular accuracy.

  18. Coordinate measuring machine test standard apparatus and method

    DOE Patents [OSTI]

    Bieg, L.F.

    1994-08-30

    A coordinate measuring machine test standard apparatus and method are disclosed which includes a rotary spindle having an upper phase plate and an axis of rotation, a kinematic ball mount attached to the phase plate concentric with the axis of rotation of the phase plate, a groove mounted at the circumference of the phase plate, and an arm assembly which rests in the groove. The arm assembly has a small sphere at one end and a large sphere at the other end. The small sphere may be a coordinate measuring machine probe tip and may have variable diameters. The large sphere is secured in the kinematic ball mount and the arm is held in the groove. The kinematic ball mount includes at least three mounting spheres and the groove is an angular locating groove including at least two locking spheres. The arm may have a hollow inner core and an outer layer. The rotary spindle may be a ratio reducer. The device is used to evaluate the measuring performance of a coordinate measuring machine for periodic recertification, including 2 and 3 dimensional accuracy, squareness, straightness, and angular accuracy. 5 figs.

  19. CBC Control Panel (Closed Brayton Cycle Control System) v 1.0

    Energy Science and Technology Software Center (OSTI)

    2012-09-13

    The CBC Control Panel is a LabviewTM Virtual Interface program that performs data acquisition, displays this data (over 100 channels), and provides control mechanisms for Closed Brayton Cycle (CBC) power conversion systems. The Program uses a state point control method that transitions the CBC from an IDLE/OFF state to RUNNING state, to SHUTDOWN, and ultimately bac~ to IDLE/OFF. During each state a set of rules control the behavior of the machine.

  20. Method and apparatus for characterizing and enhancing the functional performance of machine tools

    DOE Patents [OSTI]

    Barkman, William E; Babelay, Jr., Edwin F; Smith, Kevin Scott; Assaid, Thomas S; McFarland, Justin T; Tursky, David A; Woody, Bethany; Adams, David

    2013-04-30

    Disclosed are various systems and methods for assessing and improving the capability of a machine tool. The disclosure applies to machine tools having at least one slide configured to move along a motion axis. Various patterns of dynamic excitation commands are employed to drive the one or more slides, typically involving repetitive short distance displacements. A quantification of a measurable merit of machine tool response to the one or more patterns of dynamic excitation commands is typically derived for the machine tool. Examples of measurable merits of machine tool performance include workpiece surface finish, and the ability to generate chips of the desired length.

  1. Electrical machines and assemblies including a yokeless stator with modular lamination stacks

    DOE Patents [OSTI]

    Qu, Ronghai; Jansen, Patrick Lee; Bagepalli, Bharat Sampathkumar; Carl, Jr., Ralph James; Gadre, Aniruddha Dattatraya; Lopez, Fulton Jose

    2010-04-06

    An electrical machine includes a rotor with an inner rotor portion and an outer rotor portion, and a double-sided yokeless stator. The yokeless stator includes modular lamination stacks and is configured for radial magnetic flux flow. The double-sided yokeless stator is concentrically disposed between the inner rotor portion and the outer rotor portion of the electrical machine. Examples of particularly useful embodiments for the electrical machine include wind turbine generators, ship propulsion motors, switch reluctance machines and double-sided synchronous machines.

  2. Dual-rotor, radial-flux, toroidally-wound, permanent-magnet machine

    DOE Patents [OSTI]

    Qu, Ronghai; Lipo, Thomas A.

    2005-08-02

    The present invention provides a novel dual-rotor, radial-flux, toroidally-wound, permanent-magnet machine. The present invention improves electrical machine torque density and efficiency. At least one concentric surface-mounted permanent magnet dual-rotor is located inside and outside of a torus-shaped stator with back-to-back windings, respectively. The machine substantially improves machine efficiency by reducing the end windings and boosts the torque density by at least doubling the air gap and optimizing the machine aspect ratio.

  3. Anaerobic treatment of food wastes

    SciTech Connect (OSTI)

    Criner, G. )

    1991-04-01

    This article describes a research project at the University of Maine in which food wastes from the University cafeteria salad bar are processed in the anaerobic facility which normally treats only animal wastes. The project has benefited the University in several ways: avoidance of waste disposal fees; increased electricity co-generated from the biogas process; and use of the residual as fertilizer. An economic analysis indicated that the estimated cost of anaerobic treatment of the salad bar wastes was $4520/yr and benefits were $4793/yr. Since the digester was already in use, this cost was not factored into the analysis. Further studies are being planned.

  4. Characterization of radial turbulent fluxes in the Santander linear plasma machine

    SciTech Connect (OSTI)

    Mier, J. A. Anabitarte, E.; Sentíes, J. M.; Sánchez, R.; Newman, D. E.; Castellanos, O. F.; Milligen, B. Ph. van

    2014-05-15

    It is shown that the statistical and correlation properties of the local turbulent flux measured at different radial locations of the cold, weakly ionized plasmas inside the Santander Linear Plasma Machine [Castellanos et al., Plasma Phys. Control. Fusion 47, 2067 (2005)] are consistent with diffusive-like transport dynamics. This is in contrast to the dynamical behavior inferred from similar measurements taken in hotter, fully ionized tokamak and stellarator edge plasmas, in which long-term correlations and other features characteristic of complex, non-diffusive transport dynamics have been reported in the past. These results may shed some light on a recent controversy regarding the possible universality of the dynamics of turbulent transport in magnetized plasmas.

  5. Heat engine generator control system

    DOE Patents [OSTI]

    Rajashekara, Kaushik (Carmel, IN); Gorti, Bhanuprasad Venkata (Towson, MD); McMullen, Steven Robert (Anderson, IN); Raibert, Robert Joseph (Fishers, IN)

    1998-01-01

    An electrical power generation system includes a heat engine having an output member operatively coupled to the rotor of a dynamoelectric machine. System output power is controlled by varying an electrical parameter of the dynamoelectric machine. A power request signal is related to an engine speed and the electrical parameter is varied in accordance with a speed control loop. Initially, the sense of change in the electrical parameter in response to a change in the power request signal is opposite that required to effectuate a steady state output power consistent with the power request signal. Thereafter, the electrical parameter is varied to converge the output member speed to the speed known to be associated with the desired electrical output power.

  6. Heat engine generator control system

    DOE Patents [OSTI]

    Rajashekara, K.; Gorti, B.V.; McMullen, S.R.; Raibert, R.J.

    1998-05-12

    An electrical power generation system includes a heat engine having an output member operatively coupled to the rotor of a dynamoelectric machine. System output power is controlled by varying an electrical parameter of the dynamoelectric machine. A power request signal is related to an engine speed and the electrical parameter is varied in accordance with a speed control loop. Initially, the sense of change in the electrical parameter in response to a change in the power request signal is opposite that required to effectuate a steady state output power consistent with the power request signal. Thereafter, the electrical parameter is varied to converge the output member speed to the speed known to be associated with the desired electrical output power. 8 figs.

  7. CEBAF Control Room Renovation

    SciTech Connect (OSTI)

    Michael Spata; Thomas Oren

    2005-05-01

    The Machine Control Center at Jefferson Lab's Continuous Electron Beam Accelerator Facility was initially constructed in the early 1990s and based on proven technology of that era. Through our experience over the last 15 years and in our planning for the facilities 12 GeV upgrade we reevaluated the control room environment to capitalize on emerging visualization and display technologies and improve on workflow processes and ergonomic attributes. This effort also sets the foundation for the redevelopment of the accelerator's control system to deliver high reliability performance with improvements in beam specifications management and information flow. The complete renovation was performed over a three-week period with no interruption to beam operations. We present the results of this effort.

  8. Microcomputer-based instrument for the detection and analysis of precession motion in a gas centrifuge machine. Revision 1

    SciTech Connect (OSTI)

    Paulus, S.S.

    1986-03-01

    The Centrifuge Procession Analyzer (CPA) is a microcomputer-based instrument which detects precession motion in a gas centrifuge machine and calculates the amplitude and frequency of precession. The CPA consists of a printed circuit board which contains signal-conditioning circuitry and a 24-bit counter and an INTEL iSBC 80/24 single/board computer. Pression motion is detected by monitoring a signal generated by a variable reluctance pick-up coil in the top of the centrifuge machine. This signal is called a Fidler signal. The initial Fidler signal triggers a counter which is clocked by a high-precision, 20.000000-MHz, temperature-controlled, crystal oscillator. The contents of the counter are read by the computer and the counter reset after every ten Fidler signals. The speed of the centrifuge machine and the amplitude and frequency of precession are calculated and the results are displayed on a liquid crystal display on the front panel of the CPA. The report contains results from data generated by a Fidler signal simulator and data taken when the centrifuge was operated under three test conditions: (1) nitrogen gas during drive-up, steady state, and drive-down; (2) xenon gas during slip test, steady state, and the addition of gas; and (3) no gas during steady state. The qualitative results were consistent with experience with centrifuge machines using UF/sub 6/ in that the amplitude of precession increased and the frequency of precession decreased during drive-up, drive-down and the slip check. The magnitude of the amplitude and frequency of precession were proportional to the molecular weight of the gases in steady state.

  9. Microcomputer-based instrument for the detection and analysis of precession motion in a gas centrifuge machine

    SciTech Connect (OSTI)

    Paulus, S.S.

    1986-03-01

    The Centrifuge Precession Analyzer (CPA) is a microcomputer-based instrument which detects precession motion in a gas centrifuge machine and calculates the amplitude and frequency of precession. The CPA consists of a printed circuit board which contains signal-conditioning circuitry and a 24-bit counter and an INTEL iSBC 80-/24 single-board computer. Precession motion is detected by monitoring a signal generated by a variable reluctance pick-up coil in the top of the centrifuge machine. This signal is called a Fidler signal. The initial Fidler signal triggers a counter which is clocked by a high-precision, 20.000000-MHz, temperature-controlled, crystal oscillator. The contents of the counter are read by the computer, and the counter reset after every ten Fidler signals. The speed of the centrifuge machine and the amplitude and frequency of precession are calculated, and the results are displayed on a liquid crystal display on the front panel of the CPA. The thesis contains results from data generated by a Fidler signal simulator and data taken when the centrifuge was operated under three test conditions: (1) nitrogen gas during drive-up, steady state, and drive-down, (2) xenon gas during slip test, steady state, and the addition of gas, and (3) no gas during steady state. The qualitative results were consistent with experience with centrifuge machines UF/sub 6/ in that the amplitude of precession increased and the frequency of precession decreased during drive-up, drive-down and the slip check. The magnitude of the amplitude and frequency of precession were proportional to the molecular weight of the gases in steady state.

  10. Automated manual transmission clutch controller

    DOE Patents [OSTI]

    Lawrie, Robert E.; Reed, Jr., Richard G.; Rausen, David J.

    1999-11-30

    A powertrain system for a hybrid vehicle. The hybrid vehicle includes a heat engine, such as a diesel engine, and an electric machine, which operates as both an electric motor and an alternator, to power the vehicle. The hybrid vehicle also includes a manual-style transmission configured to operate as an automatic transmission from the perspective of the driver. The engine and the electric machine drive an input shaft which in turn drives an output shaft of the transmission. In addition to driving the transmission, the electric machine regulates the speed of the input shaft in order to synchronize the input shaft during either an upshift or downshift of the transmission by either decreasing or increasing the speed of the input shaft. When decreasing the speed of the input shaft, the electric motor functions as an alternator to produce electrical energy which may be stored by a storage device. Operation of the transmission is controlled by a transmission controller which receives input signals and generates output signals to control shift and clutch motors to effect smooth launch, upshift shifts, and downshifts of the transmission, so that the transmission functions substantially as an automatic transmission from the perspective of the driver, while internally substantially functioning as a manual transmission.

  11. Characterizing the Plasma of the Resistive Wall Machine

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Plasma of the Rotating Wall Machine by David A. Hannum A dissertation submitted in partial fulfillment of the requirements for the degree of Doctor of Philosophy (Physics) at the University of Wisconsin-Madison 2010 Copyright ©2010 David A. Hannum. Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version 1.3 or any later version published by the Free Software Foundation; with no Invariant Sections, no Front-Cover Texts,

  12. A pipe cleaning machine: ERIP recommendation No. 571

    SciTech Connect (OSTI)

    Bratcher, H. Jr.; Hinick, M.B.; Balsam, J.W.

    1992-06-12

    The subject invention, ``A Pipe Cleaning Machine,`` known as ``Buffy,`` is a device that strips pipeline of its coating down to the metal. The apparatus consists of a series of motor-driven metal brushes mounted on a ring structure that fits the around the pipe`s circumference. Once stripped, the pipeline may or may not be abrasive-blasted, but is then coated and wrapped, and the trench is back-filled. Present models of the Buffy can be used on pipe up to 36`` in diameter. One of the device`s unique features is its ability to operate while the pipeline remains in service.

  13. Lightweight piston-rod assembly for a reciprocating machine

    DOE Patents [OSTI]

    Corey, John A.; Walsh, Michael M.

    1986-01-01

    In a reciprocating machine, there is provided a hollow piston including a dome portion on one end and a base portion on the opposite end. The base portion includes a central bore into which a rod is hermetically fixed in radial and angular alignment. The extending end of the rod has a reduced diameter portion adapted to fit into the central bore of a second member such as a cross-head assembly, and to be secured thereto in radial and axial alignment with the piston.

  14. Magnetic field measurements via visible spectroscopy on the Z machine

    SciTech Connect (OSTI)

    Gomez, M. R. Hansen, S. B.; Peterson, K. J.; Bliss, D. E.; Carlson, A. L.; Lamppa, D. C.; Rochau, G. A.; Schroen, D. G.

    2014-11-15

    Sandia's Z Machine uses its high current to magnetically implode targets relevant to inertial confinement fusion. Since target performance is highly dependent on the applied drive field, measuring magnetic field at the target is essential for accurate simulations. Recently, the magnetic field at the target was measured through splitting of the sodium 3s-3p doublet at 5890 and 5896 Ă…. Spectroscopic dopants were applied to the exterior of the target, and spectral lines were observed in absorption. Magnetic fields in excess of 200 T were measured, corresponding to drive currents of approximately 5 MA early in the pulse.

  15. Apparatus For Laminating Segmented Core For Electric Machine

    DOE Patents [OSTI]

    Lawrence, Robert Anthony; Stabel, Gerald R

    2003-06-17

    A segmented core for an electric machine includes segments stamped from coated electric steel. The segments each have a first end, a second end, and winding openings. A predetermined number of segments are placed end-to-end to form layers. The layers are stacked such that each of the layers is staggered from adjacent layers by a predetermined rotation angle. The winding openings of each of the layers are in vertical alignment with the winding openings of the adjacent layers. The stack of layers is secured to form the segmented core.

  16. ISSUANCE 2015-07-15: Energy Conservation Program: Test Procedure for Refrigerated Bottled or Canned Beverage Vending Machines, Final Rule

    Broader source: Energy.gov [DOE]

    Energy Conservation Program: Test Procedure for Refrigerated Bottled or Canned Beverage Vending Machines, Final Rule

  17. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Building Controls, Motors, Motor VFDs, CustomOthers pending approval, Other EE, Food Service Equipment, Vending Machine Controls, Commercial Cooking Equipment, LED...

  18. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Mgmt. SystemsBuilding Controls, Motor VFDs, CustomOthers pending approval, Other EE, Food Service Equipment, Vending Machine Controls, LED Lighting Alliant Energy Interstate...

  19. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Mgmt. SystemsBuilding Controls, Motor VFDs, CustomOthers pending approval, Other EE, Food Service Equipment, Vending Machine Controls, LED Lighting Tacoma Power- Commercial and...

  20. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Controls, Windows, Motors, Motor VFDs, CustomOthers pending approval, Other EE, Food Service Equipment, Vending Machine Controls, LED Lighting, Commercial Refrigeration...

  1. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    SystemsBuilding Controls, Motors, Motor VFDs, CustomOthers pending approval, Other EE, Food Service Equipment, Vending Machine Controls, Data Center Equipment, LED Lighting,...

  2. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    SystemsBuilding Controls, Motor VFDs, CustomOthers pending approval, Other EE, Food Service Equipment, Vending Machine Controls, LED Lighting Unitil (Electric)- Commercial...

  3. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    SystemsBuilding Controls, Motors, Motor VFDs, CustomOthers pending approval, Other EE, Food Service Equipment, Vending Machine Controls, Commercial Cooking Equipment, LED...

  4. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Controls, Windows, Motors, Motor VFDs, CustomOthers pending approval, Other EE, Food Service Equipment, Vending Machine Controls, Commercial Refrigeration Equipment...

  5. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Mgmt. SystemsBuilding Controls, Motors, Motor VFDs, CustomOthers pending approval, Food Service Equipment, Vending Machine Controls, Personal Computing Equipment, Commercial...

  6. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Lighting, Lighting ControlsSensors, Motors, CustomOthers pending approval, Other EE, Food Service Equipment, Vending Machine Controls, LED Lighting, Commercial Refrigeration...

  7. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Mgmt. SystemsBuilding Controls, Motor VFDs, CustomOthers pending approval, Other EE, Food Service Equipment, Vending Machine Controls, LED Lighting, Tankless Water Heater PEPCO-...

  8. Tax Credits, Rebates & Savings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Mgmt. SystemsBuilding Controls, Motor VFDs, CustomOthers pending approval, Other EE, Food Service Equipment, Vending Machine Controls, LED Lighting, Tankless Water Heater...

  9. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Building Controls, Motors, Motor VFDs, CustomOthers pending approval, Other EE, Food Service Equipment, Vending Machine Controls, Commercial Refrigeration Equipment Michigan...

  10. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    SystemsBuilding Controls, Motors, Motor VFDs, CustomOthers pending approval, Other EE, Food Service Equipment, Vending Machine Controls, Commercial Refrigeration Equipment City...

  11. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Controls, Windows, Motors, Motor VFDs, CustomOthers pending approval, Other EE, Food Service Equipment, Vending Machine Controls, Commercial Refrigeration Equipment Local...

  12. Tax Credits, Rebates & Savings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Controls, CustomOthers pending approval, Other EE, Food Service Equipment, Vending Machine Controls, Personal Computing Equipment, Data Center Equipment, LED Lighting,...

  13. Flexible Distributed Energy and Water from Waste for the Food and Beverage

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Industry - Fact Sheet, 2014 | Department of Energy Flexible Distributed Energy and Water from Waste for the Food and Beverage Industry - Fact Sheet, 2014 Flexible Distributed Energy and Water from Waste for the Food and Beverage Industry - Fact Sheet, 2014 GE Global Research, in collaboration with GE Water & Process Technologies, GE Intelligent Platforms, SRA International, and Anheuser-Busch, developed a systematic plant-wide automation for online monitoring and supervisory control. The

  14. Digestion of frozen/thawed food waste in the hybrid anaerobic solid-liquid system

    SciTech Connect (OSTI)

    Stabnikova, O. Liu, X.Y.; Wang, J.Y.

    2008-07-01

    The hybrid anaerobic solid-liquid (HASL) system, which is a modified two-phase anaerobic digester, is to be used in an industrial scale operation to minimize disposal of food waste at incineration plants in Singapore. The aim of the present research was to evaluate freezing/thawing of food waste as a pre-treatment for its anaerobic digestion in the HASL system. The hydrolytic and fermentation processes in the acidogenic reactor were enhanced when food waste was frozen for 24 h at -20 deg. C and then thawed for 12 h at 25 deg. C (experiment) in comparison with fresh food waste (control). The highest dissolved COD concentrations in the leachate from the acidogenic reactors were 16.9 g/l on day 3 in the control and 18.9 g/l on day 1 in the experiment. The highest VFA concentrations in the leachate from the acidogenic reactors were 11.7 g/l on day 3 in the control and 17.0 g/l on day 1 in the experiment. The same volume of methane was produced during 12 days in the control and 7 days in the experiment. It gave the opportunity to diminish operational time of batch process by 42%. The effect of freezing/thawing of food waste as pre-treatment for its anaerobic digestion in the HASL system was comparable with that of thermal pre-treatment of food waste at 150 deg. C for 1 h. However, estimation of energy required either to heat the suspended food waste to 150 deg. C or to freeze the same quantity of food waste to -20 deg. C showed that freezing pre-treatment consumes about 3 times less energy than thermal pre-treatment.

  15. Ethanol: Producting Food, Feed, and Fuel

    Broader source: Energy.gov [DOE]

    At the August 7, 2008 joint quarterly Web conference of DOE's Biomass and Clean Cities programs, Todd Sneller (Nebraska Ethanol Board) discussed the food versus fuel issue.

  16. Covered Product Category: Hot Food Holding Cabinets

    Broader source: Energy.gov [DOE]

    The Federal Energy Management Program (FEMP) provides acquisition guidance for hot food holding cabinets, which are covered by the ENERGY STAR program.

  17. Pole-phase modulated toroidal winding for an induction machine

    DOE Patents [OSTI]

    Miller, John Michael (Saline, MI); Ostovic, Vlado (Weinheim, DE)

    1999-11-02

    A stator (10) for an induction machine for a vehicle has a cylindrical core (12) with inner and outer slots (26, 28) extending longitudinally along the inner and outer peripheries between the end faces (22, 24). Each outer slot is associated with several adjacent inner slots. A plurality of toroidal coils (14) are wound about the core and laid in the inner and outer slots. Each coil occupies a single inner slot and is laid in the associated outer slot thereby minimizing the distance the coil extends from the end faces and minimizing the length of the induction machine. The toroidal coils are configured for an arbitrary pole phase modulation wherein the coils are configured with variable numbers of phases and poles for providing maximum torque for cranking and switchable to a another phase and pole configuration for alternator operation. An adaptor ring (36) circumferentially positioned about the stator improves mechanical strength, and provides a coolant channel manifold (34) for removing heat produced in stator windings during operation.

  18. Fault diagnosis via neural networks: The Boltzmann machine

    SciTech Connect (OSTI)

    Marseguerra, M.; Zio, E. . Dept. of Nuclear Engineering)

    1994-07-01

    The Boltzmann machine is a general-purpose artificial neural network that can be used as an associative memory as well as a mapping tool. The usual information entropy is introduced, and a network energy function is suitably defined. The network's training procedure is based on the simulated annealing during which a combination of energy minimization and entropy maximization is achieved. An application in the nuclear reactor field is presented in which the Boltzmann input-output machine is used to detect and diagnose a pipe break in a simulated auxiliary feedwater system feeding two coupled steam generators. The break may occur on either the hot or the cold leg of any of the two steam generators. The binary input data to the network encode only the trends of the thermohydraulic signals so that the network is actually a polarity device. The results indicate that the trained neural network is actually capable of performing its task. The method appears to be robust enough so that it may also be applied with success in the presence of substantial amounts of noise that cause the network to be fed with wrong signals.

  19. Effective and efficient optics inspection approach using machine learning algorithms

    SciTech Connect (OSTI)

    Abdulla, G; Kegelmeyer, L; Liao, Z; Carr, W

    2010-11-02

    The Final Optics Damage Inspection (FODI) system automatically acquires and utilizes the Optics Inspection (OI) system to analyze images of the final optics at the National Ignition Facility (NIF). During each inspection cycle up to 1000 images acquired by FODI are examined by OI to identify and track damage sites on the optics. The process of tracking growing damage sites on the surface of an optic can be made more effective by identifying and removing signals associated with debris or reflections. The manual process to filter these false sites is daunting and time consuming. In this paper we discuss the use of machine learning tools and data mining techniques to help with this task. We describe the process to prepare a data set that can be used for training and identifying hardware reflections in the image data. In order to collect training data, the images are first automatically acquired and analyzed with existing software and then relevant features such as spatial, physical and luminosity measures are extracted for each site. A subset of these sites is 'truthed' or manually assigned a class to create training data. A supervised classification algorithm is used to test if the features can predict the class membership of new sites. A suite of self-configuring machine learning tools called 'Avatar Tools' is applied to classify all sites. To verify, we used 10-fold cross correlation and found the accuracy was above 99%. This substantially reduces the number of false alarms that would otherwise be sent for more extensive investigation.

  20. A Numerical Comparison of Rule Ensemble Methods and Support Vector Machines

    Office of Scientific and Technical Information (OSTI)

    (Technical Report) | SciTech Connect A Numerical Comparison of Rule Ensemble Methods and Support Vector Machines Citation Details In-Document Search Title: A Numerical Comparison of Rule Ensemble Methods and Support Vector Machines Machine or statistical learning is a growing field that encompasses many scientific problems including estimating parameters from data, identifying risk factors in health studies, image recognition, and finding clusters within datasets, to name just a few

  1. Review of safety guidelines and licensing procedures applicable in Italy with regard to fusion machines

    SciTech Connect (OSTI)

    Sgalambro, G.

    1993-06-01

    A consistent set of general safety criteria has been set up in Italy dealing with fusion machines, considering also the most recent recommendations issued by ICRP. The paper gives a short discussion of the more safety relevant aspects in the design of fusion machines starting from the consideration of the applicable dose limits. The procedure for the licensing of fusion machines is presented in the second part of the paper.

  2. AMO FOA Targets Advanced Components for Next-Generation Electric Machines |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy FOA Targets Advanced Components for Next-Generation Electric Machines AMO FOA Targets Advanced Components for Next-Generation Electric Machines March 19, 2015 - 10:21am Addthis AMO's Next Generation Electric Machines (NGEM) program announced up to $20 million is now available to develop a new generation of energy efficient, high power density, high speed integrated MV drive systems for a wide variety of critical energy applications. This Financial Opportunity

  3. DOE - Office of Legacy Management -- Simmons Machine and Tool Inc - NY 35

    Office of Legacy Management (LM)

    Simmons Machine and Tool Inc - NY 35 FUSRAP Considered Sites Site: SIMMONS MACHINE AND TOOL, INC (NY.35) Eliminated from consideration under FUSRAP Designated Name: Not Designated Alternate Name: None Location: 1000 North Broadway , Albany , New York NY.35-1 Evaluation Year: 1987 NY.35-2 Site Operations: Tested equipment and machined uranium to test the equipment (one time event). NY.35-1 NY.35-2 Site Disposition: Eliminated - Potential for contamination considered remote due to limited scope

  4. Characterization of Contact and Bulk Thermal Resistance of Laminations for Electric Machines

    SciTech Connect (OSTI)

    Cousineau, J. Emily; Bennion, Kevin; DeVoto, Doug; Mihalic, Mark; Narumanchi, Sreekant

    2015-06-30

    The ability to remove heat from an electric machine depends on the passive stack thermal resistances within the machine and the convective cooling performance of the selected cooling technology. This report focuses on the passive thermal design, specifically properties of the stator and rotor lamination stacks. Orthotropic thermal conductivity, specific heat, and density are reported. Four materials commonly used in electric machines were tested, including M19 (29 and 26 gauge), HF10, and Arnon 7 materials.

  5. Using condition monitoring for maintenance, control of hydro plants

    SciTech Connect (OSTI)

    Brown, N.; Varo, R.; Morras, F.A.

    1994-12-31

    Electric utilities are actively seeking ways of optimizing the economics of their operations by improving productivity and reducing time and money spent on maintenance. Iberdrola, a Spanish utility, is using advanced machine condition-monitoring technology to centralize control and maintenance of its hydropower projects as a means of achieving those goals. The company is using a blend of technologies to supervise their projects from a regional control center. The monitoring scheme makes use of data from on-line, machine-condition monitors, displays from in-plant audio asnd video equipment, and analysis from the control center`s SCADA system.

  6. Numerical Simulation of Earth Pressure on Head Chamber of Shield Machine with FEM

    SciTech Connect (OSTI)

    Li Shouju; Kang Chengang [State Key Laboratory of structural analysis for industrial equipment, Dalian University of Technology, Dalian 116023 (China); Sun, Wei [School of Mechanical Engineering, Dalian University of Technology, Dalian 116023 (China); Shangguan Zichang [School of Civil and Hydraulic Engineering, Dalian University of Technology, Dalian 116023 (China); Institute of Civil Engineering, Dalian Fishery University, Dalian 116023 (China)

    2010-05-21

    Model parameters of conditioned soils in head chamber of shield machine are determined based on tree-axial compression tests in laboratory. The loads acting on tunneling face are estimated according to static earth pressure principle. Based on Duncan-Chang nonlinear elastic constitutive model, the earth pressures on head chamber of shield machine are simulated in different aperture ratio cases for rotating cutterhead of shield machine. Relationship between pressure transportation factor and aperture ratio of shield machine is proposed by using aggression analysis.

  7. Analysis of Strand-Specific RNA-Seq Data Using Machine Learning...

    Office of Scientific and Technical Information (OSTI)

    Clostridium thermocellum using a machine-learning approach. ... Nucleic Acids Research; Journal ID: ISSN 0305-1048 ... Country of Publication: United States Language: English ...

  8. Watt-Sun: A Multi-Scale, Multi-Model, Machine-Learning Solar...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    forecasting technology will be developed that leverages big data processing, deep machine learning, and cloud modeling integrated in a universal platform with an open architecture. ...

  9. Design of a Modular E-Core Flux Concentrating Axial Flux Machine: Preprint

    SciTech Connect (OSTI)

    Husain, Tausif; Sozer, Yilmaz; Husain, Iqbal; Muljadi, Eduard

    2015-08-24

    In this paper a novel E-Core axial flux machine is proposed. The machine has a double-stator, single-rotor configuration with flux-concentrating ferrite magnets and pole windings across each leg of an E-Core stator. E-Core stators with the proposed flux-concentrating rotor arrangement result in better magnet utilization and higher torque density. The machine also has a modular structure facilitating simpler construction. This paper presents a single-phase and a three-phase version of the E-Core machine. Case studies for a 1.1-kW, 400-rpm machine for both the single-phase and three-phase axial flux machines are presented. The results are verified through 3D finite element analysis. facilitating simpler construction. This paper presents a single-phase and a three-phase version of the E-Core machine. Case studies for a 1.1-kW, 400-rpm machine for both the single-phase and three-phase axial flux machines are presented. The results are verified through 3D finite element analysis.

  10. MECS 2006 - Food and Beverage | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Food and Beverage MECS 2006 - Food and Beverage Manufacturing Energy and Carbon Footprint for Food and Beverage (NAICS 311, 312) Sector with Total Energy Input, October 2012 (MECS 2006) All available footprints and supporting documents Manufacturing Energy and Carbon Footprint PDF icon Food and Beverage More Documents & Publications Food and Beverage (2010 MECS) MECS 2006 - Alumina and Aluminum MECS 2006 - Cement

  11. Weld Properties of a Free Machining Stainless Steel

    SciTech Connect (OSTI)

    J. A. Brooks; S. H. Goods; C. V. Robino

    2000-08-01

    The all weld metal tensile properties from gas tungsten arc and electron beam welds in free machining austenitic stainless steels have been determined. Ten heats with sulfur contents from 0.04 to 0.4 wt.% and a wide range in Creq/Nieq ratios were studied. Tensile properties of welds with both processes were related to alloy composition and solidification microstructure. The yield and ultimate tensile strengths increased with increasing Creq/Nieq ratios and ferrite content, whereas the ductility measured by RA at fracture decreased with sulfur content. Nevertheless, a range in alloy compositions was identified that provided a good combination of both strength and ductility. The solidification cracking response for the same large range of compositions are discussed, and compositions identified that would be expected to provide good performance in welded applications.

  12. Topical Report Tantalum – 2.5% Tungsten Machinability Testing

    SciTech Connect (OSTI)

    L. J. Lazarus

    2009-09-02

    Protection Association (NFPA). NFPA 484, Standard for Combustible Metals, Chapter 9 Tantalum and Annex E, supplemental Information on Tantalum require cutting oil be used when machining tantalum because it burns at such a high temperature that it breaks down the water in a water-based metalworking fluid (MWF). The NFPA guide devotes approximately 20 pages to this material. The Kansas City Plant (KCP) uses Fuchs Lubricants Ecocut Base 44 LVC as a MWF. This is a highly chlorinated oil with a high flash point (above 200° F). The chlorine is very helpful in preventing BUE (Built Up Edge) that occurs frequently with this very gummy material. The Ecocut is really a MWF additive that Fuchs uses to add chlorinated fats to other non-chlorinated MWF.

  13. Beam-machine Interaction at the CERN LHC

    SciTech Connect (OSTI)

    Boccone, V.; Bruce, R.; Brugger, M.; Calviani, M.; Cerutti, F. Esposito, L.S.; Ferrari, A.; Lechner, A.; Mereghetti, A.; Nowak, E.; Shetty, N.V.; Skordis, E.; Versaci, R.; Vlachoudis, V.

    2014-06-15

    The radiation field generated by a high energy and intensity accelerator is of concern in terms of element functionality threat, component damage, electronics reliability, and material activation, but also provides signatures that allow actual operating conditions to be monitored. The shower initiated by an energetic hadron involves many different physical processes, down to slow neutron interactions and fragment de-excitation, which need to be accurately described for design purposes and to interpret operation events. The experience with the transport and interaction Monte Carlo code FLUKA at the Large Hadron Collider (LHC), operating at CERN with 4 TeV proton beams (and equivalent magnetic rigidity Pb beams) and approaching nominal luminosity and energy, is presented. Design, operation and upgrade challenges are reviewed in the context of beam-machine interaction account and relevant benchmarking examples based on radiation monitor measurements are shown.

  14. Main roll for an air press of a papermaking machine

    DOE Patents [OSTI]

    Beck, David A.

    2004-03-09

    A roll for use in an air press assembly of a papermaking machine has a pair of ends associated therewith. The roll includes a pair of edge portions with each edge portion extending to one of the pair of ends. Each edge portion has an edge surface portion composed of a first material, the first material having a first hardness. The roll further includes a middle portion located between the pair of edge portions, the middle portion having a middle surface portion composed of a second material. The second material has a second hardness, the second material being harder than the first material. The first material is preferably a soft, seal material which promotes reduced air leakage from the air press assembly.

  15. Diamond Wire Saw for Precision Machining of Laser Target Components

    SciTech Connect (OSTI)

    Bono, M J; Bennett, D W

    2005-08-08

    The fabrication of precision laser targets requires a wide variety of specialized mesoscale manufacturing techniques. The diamond wire saw developed in this study provides the capability to precisely section meso-scale workpieces mounted on the assembly stations used by the Target Fabrication Group. This new capability greatly simplifies the fabrication of many types of targets and reduces the time and cost required to build the targets. A variety of materials are used to fabricate targets, including metals, plastics with custom designed chemical formulas, and aerogels of various densities. The materials are usually provided in the form of small pieces or cast rods that must be machined to the required shape. Many of these materials, such as metals and some plastics, can be trimmed using a parting tool on a diamond turning machine. However, other materials, such as aerogels and brittle materials, cannot be adequately cut with a parting tool. In addition, the geometry of the parts often requires that the workpieces be held in a special assembly station, which excludes the use of a parting tool. In the past, these materials were sectioned using a small, handheld coping saw that used a diamond-impregnated wire as a blade. This miniature coping saw was effective, but it required several hours to cut through certain materials. Furthermore, the saw was guided by hand and often caused significant damage to fragile aerogels. To solve these problems, the diamond wire saw shown in Figure 1 was developed. The diamond wire saw is designed to machine through materials that are mounted in the Target Fabrication Group's benchtop assembly stations. These assembly stations are the primary means of aligning and assembling target components, and there is often a need to machine materials while they are mounted in the assembly stations. Unfortunately, commercially available saws are designed for very different applications and are far too large to be used with the assembly stations. Therefore, a custom diamond wire saw was designed and constructed. The diamond wire saw cuts through workpieces using a continuous loop of diamond-impregnated wire of length 840 mm. The wire loop runs around several idler pulleys and is driven by a simple geared DC motor that rotates at 17 rpm. The linear speed of the wire is 107 inches/minute. The saw is oriented at an angle of 20{sup o} from horizontal, so the operator can view the wire through the cutout at the front end of the saw. When looking through a microscope or camera with a horizontal line of sight, the operator can clearly see the wire as it cuts through the workpiece, as shown in the right side of Figure 1. The saw is mounted on a two-axis stage that allows the operator to align the wire with the workpiece. To cut through the workpiece, the operator drives the wire through the workpiece by turning the feed micrometer. An image of the interior of the diamond wire saw appears in Figure 2. This picture was taken after removing the protective cover plate from the saw.

  16. 2016 Rube Goldberg Machine Contest | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Rube Goldberg Machine Contest 1 of 33 1 of 33 2 of 33 3 of 33 4 of 33 5 of 33 6 of 33 7 of 33 8 of 33 9 of 33 10 of 33 11 of 33 12 of 33 13 of 33 14 of 33 15 of 33 16 of 33 17 of 33 18 of 33 19 of 33 20 of 33 21 of 33 22 of 33 23 of 33 24 of 33 25 of 33 26 of 33 27 of 33 28 of 33 29 of 33 30 of 33 31 of 33 32 of 33 33 of 33 Browse By - Any - Energy -Energy efficiency --Vehicles ---Automotive engineering ---Hybrid & electric vehicles -Energy sources --Nuclear energy -Energy usage --Energy

  17. Pumpkin Power: Turning Food Waste into Energy | Department of...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Pumpkin Power: Turning Food Waste into Energy Pumpkin Power: Turning Food Waste into Energy November 1, 2013 - 1:28pm Addthis Pumpkin Power: Turning Food Waste into Energy Matthew...

  18. Coupling for joining a ball nut to a machine tool carriage

    DOE Patents [OSTI]

    Gerth, Howard L.

    1979-01-01

    The present invention relates to an improved coupling for joining a lead screw ball nut to a machine tool carriage. The ball nut is coupled to the machine tool carriage by a plurality of laterally flexible bolts which function as hinges during the rotation of the lead screw for substantially reducing lateral carriage movement due to wobble in the lead screw.

  19. Control system health test system and method

    DOE Patents [OSTI]

    Hoff, Brian D.; Johnson, Kris W.; Akasam, Sivaprasad; Baker, Thomas M.

    2006-08-15

    A method is provided for testing multiple elements of a work machine, including a control system, a component, a sub-component that is influenced by operations of the component, and a sensor that monitors a characteristic of the sub-component. In one embodiment, the method is performed by the control system and includes sending a command to the component to adjust a first parameter associated with an operation of the component. Also, the method includes detecting a sensor signal from the sensor reflecting a second parameter associated with a characteristic of the sub-component and determining whether the second parameter is acceptable based on the command. The control system may diagnose at least one of the elements of the work machine when the second parameter of the sub-component is not acceptable.

  20. Trade My Food | Open Energy Information

    Open Energy Info (EERE)

    search for food they would like to trade for. Example: Alicia grows parsley, Bob is a fisherman. Alicia wants some fish. Bob wants some parsley. They find each other on...