National Library of Energy BETA

Sample records for lpg liquid petroleum

  1. Local government energy management: liquid petroleum gas (LPG) as a motor vehicle fuel

    SciTech Connect (OSTI)

    McCoy, G.A.; Kerstetter, J.

    1983-10-01

    The retrofit or conversion of automotive engines to operate on liquid petroleum gas (LPG) or propane fuel is one of many potentially cost-effective strategies for reducing a local government's annual fleet operating and maintenance costs. The cost effectiveness of an LPG conversion decision is highly dependent on the initial conversion cost, vehicle type, current and projected fuel costs, vehicle fuel economy (miles per gallon), and yearly average mileage. A series of plots have been developed which indicate simple paybacks for the conversion of several vehicle types (passenger car, small and standard pickups, and two and three ton trucks) over a wide range of fuel economies and annual usage patterns. A simple payback of less than three years can be achieved for vehicles with poor fuel economy and high annual use. The figures provided in this report may be used by fleet management personnel as a screening tool to identify those passenger cars, small or standard pickups, or light duty trucks which are candidates for LPG conversion. In addition to examining the benefits of an LPG conversion, local governments should also consider the competing energy management strategies of downsizing, and the acquisition of fuel efficient, diesel powered vehicles.

  2. Direct liquid injection of liquid petroleum gas

    SciTech Connect (OSTI)

    Lewis, D.J.; Phipps, J.R.

    1984-02-14

    A fuel injector and injection system for injecting liquified petroleum gas (LPG) into at least one air/fuel mixing chamber from a storage means that stores pressurized LPG in its liquid state. The fuel injector (including a body), adapted to receive pressurized LPG from the storage means and for selectively delivering the LPG to the air/fuel mixing chamber in its liquified state. The system including means for correcting the injector activation signal for pressure and density variations in the fuel.

  3. Legal nature of LPG (liquefied petroleum gas) regulation

    SciTech Connect (OSTI)

    Liddell, G.

    1986-08-01

    The commercial exploitation of Liquefied Petroleum Gas (LPG) in New Zealand has occurred without a particular and comprehensive concern for any legal implications. The paper in Part I examines definitional questions, assesses in Part II the ability of courts and quasi-courts to evaluate risks associated with the product, examines in Part III the utility of common law remedies for injuries or associated with or arising from LPG, analyzes in Part IV the statutory regulation of LPG, concentrating particularly on the Dangerous Goods (Class 2 - Gases) Regulations 1980, discusses in Part V recent planning case-law concerning LPG development, and concludes that some reform is necessary to produce a more-coherent and precise regulatory regime that takes into account both the needs of developers and those affected by the development of LPG.

  4. Cracking in liquid petroleum gas Horton spheres

    SciTech Connect (OSTI)

    Trivedi, D.K. Gupta, S.C.

    1997-07-01

    A gas processing plant on the western coast of India produces sweet gas after processing sour natural gas. Liquid petroleum gas (LPG) is recovered from the sweet gas. The LPG, containing a H{sub 2}S concentration of 10 ppm to 20 ppm, is stored in Horton spheres, each 17 m in diameter with a capacity of {minus}27 C to 55 C. Horton spheres for containing liquid petroleum gas (LPG) were fabricated on-site using prestressed plates of high-strength carbon steel (CS) SA 537 Class-1 with post-weld heat treatment. High-residual tensile stresses and hydrogen absorption from H{sub 2}S present in LPG could be the cause of cracking at weld and heat-affected zone interfaces at high hardness locations. Recommendations are given for inspection and use of lower-strength CS and improved welding procedures.

  5. Upgrading Fischer-Tropsch LPG (liquefied petroleum gas) with the Cyclar process

    SciTech Connect (OSTI)

    Gregor, J.H.; Gosling, C.D.; Fullerton, H.E.

    1989-04-28

    The use of the UOP/BP Cyclar{reg sign} process for upgrading Fischer-Tropsch (F-T) liquefied petroleum gas (LPG) was studied at UOP{reg sign}. The Cyclar process converts LPG into aromatics. The LPG derived from F-T is highly olefinic. Two routes for upgrading F-T LPG were investigated. In one route, olefinic LPG was fed directly to a Cyclar unit (Direct Cyclar). The alternative flow scheme used the Huels CSP process to saturate LPG olefins upstream of the Cyclar unit (Indirect Cyclar). An 18-run pilot plant study verified that each route is technically feasible. An economic evaluation procedure was designed to choose between the Direct and Indirect Cyclar options for upgrading LPG. Four situations involving three different F-T reactor technologies were defined. The main distinction between the cases was the degree of olefinicity, which ranged between 32 and 84 wt % of the fresh feed. 8 refs., 80 figs., 44 tabs.

  6. System and method for converting wellhead gas to liquefied petroleum gases (LPG)

    SciTech Connect (OSTI)

    May, R.L.; Sinclair, B.W.

    1984-07-31

    A method of converting natural wellhead gas to liquefied petroleum gases (LPG) may comprise the steps of: separating natural gas from petroleum fluids exiting a wellhead; compressing the natural gas; refrigerating the natural gas, liquefying at least a portion thereof; separating LPG from gas vapors of the refrigerated natural gas; storing the separated LPG in a storage tank with a vapor space therein; and recirculating a portion of the LPG vapors in the storage tank with the natural gas exiting the wellhead to enhance recovery of LPG. A system for performing the method may comprise: a two-stage gas compressor connected to the wellhead; a refrigeration unit downstream of the gas compressor for refrigerating the compressed gases therefrom; at least one product separator downstream of the refrigerator unit for receiving refrigerated and compressed gases discharged from the refrigerator unit and separating LPG therein from gases remaining in vapor form; and a storage tank for receiving and storing the separated LPG therein, the storage tank having a vapor space therein connected upstream of the gas compressor through a pressure regulator allowing recirculation of some LPG vapors with the natural gases through said system.

  7. Latest techniques and equipment for the conversion of motor vehicles to LPG/petroleum use

    SciTech Connect (OSTI)

    Armstrong, R.

    1980-01-01

    Liquified petroleum gases (LPG) has been used for transportation in Europe, the United States, Japan and to a much lesser extent in Australia for many years. In most cases, the vehicles have been powered by engines designed for petrol operation and subsequently converted to use LPG. The application of LPG as an automotive fuel in different countries depends heavily on the availability of the fuel and the tax policy of the government. The demand for dual fuel equipment is increasing. Some of the problems facing Australia to convert vehicles to LPG use emphasize the institutional and hardware obstacles. Before LPG can be considered to be a safe, viable alternative fuel to petrol, improvements will have to be made in safety standards, in reduced exhaust emissions, in increased fuel efficiency, and in the involvement of car manufacturers. (SAC)

  8. System and method for converting wellhead gas to liquefied petroleum gases (LPG)

    SciTech Connect (OSTI)

    May, R.L.; Snow, N.J. Jr.

    1983-12-06

    A method of converting natural wellhead gas to liquefied petroleum gases (LPG) may comprise the steps of: separating natural gas from petroleum fluids exiting a well-head; compressing the natural gas; refrigerating the natural gas, liquefying at least a portion thereof; and separating LPG from gas vapors of the refrigerated natural gas. A system for performing the method may comprise: a two-stage gas compressor connected to the wellhead; a refrigeration unit downstream of the gas compressor for cooling the compressed gases therefrom; and a product separator downstream of the refrigeration unit for receiving cooled and compressed gases discharged from the refrigeration unit and separating LPG therein from gases remaining in vapor form.

  9. Australian liquids-handling system cuts surges to LPG plant

    SciTech Connect (OSTI)

    McKee, G.; Stenner, T.D. )

    1990-08-06

    This paper reports how a pipeline liquids-handling facility recently commissioned allows gas production to be quickly ramped up to meet customer demand. Its design eliminates trouble-some liquid surges which had hampered plant operations. The pipeline-loop system, located at the Wallumbilla LPG processing plant, Queensland, was built for 60 of the cost of an equivalently sized conventional slug catcher. Its control system enables automatic, unattended handling of liquid surges and pigging slugs from the 102-km Silver Springs to Wallumbilla two-phase pipeline. Because of this system's simple hydraulics, normal slug-catcher piping design problems are eliminated. Safety is improved because the potentially hazardous condensate liquid is contained in a buried pipeline.

  10. LIQUID PROPANE GAS (LPG) STORAGE AREA BOILING LIQUID EXPANDING VAPOR EXPLOSION (BLEVE) ANALYSIS

    SciTech Connect (OSTI)

    PACE, M.E.

    2004-01-13

    The PHA and the FHAs for the SWOC MDSA (HNF-14741) identified multiple accident scenarios in which vehicles powered by flammable gases (e.g., propane), or combustible or flammable liquids (e.g., gasoline, LPG) are involved in accidents that result in an unconfined vapor cloud explosion (UVCE) or in a boiling liquid expanding vapor explosion (BLEVE), respectively. These accident scenarios are binned in the Bridge document as FIR-9 scenarios. They are postulated to occur in any of the MDSA facilities. The LPG storage area will be in the southeast corner of CWC that is relatively remote from store distaged MAR. The location is approximately 30 feet south of MO-289 and 250 feet east of 2401-W by CWC Gate 10 in a large staging area for unused pallets and equipment.

  11. Additional Development of a Dedicated Liquefied Petroleum Gas (LPG) Ultra Low Emissions Vehicle (ULEV)

    SciTech Connect (OSTI)

    IMPCO Technologies

    1998-10-28

    This report describes the last in a series of three projects designed to develop a commercially competitive LPG light-duty passenger car that meets California ULEV standards and corporate average fuel economy (CAFE) energy efficiency guidelines for such a vehicle. In this project, IMPCO upgraded the vehicle's LPG vapor fuel injection system and performed emissions testing. The vehicle met the 1998 ULEV standards successfully, demonstrating the feasibility of meeting ULEV standards with a dedicated LPG vehicle.

  12. Petroleum & Other Liquids

    Gasoline and Diesel Fuel Update (EIA)

    Map details Alaska Arizona Full Region Hawaii Marine Movements Northern California and Northern Nevada Pacific Northwest Southern California and Southern Nevada PADD 5 Transportation Fuels Markets Release date: September 30, 2015 Introduction This study examines supply, demand, and distribution of transportation fuels in Petroleum Administration for Defense District (PADD) 5, a region that includes the western states of California, Arizona, Nevada, Oregon, Washington, Alaska, and Hawaii. For

  13. Fire protection considerations for the design and operation of liquefied petroleum gas (LPG) storage facilities

    SciTech Connect (OSTI)

    Not Available

    1989-01-01

    This standard addresses the design, operation, and maintenance of LPG storage facilities from the standpoint of prevention and control of releases, fire-protection design, and fire-control measures, as well as the history of LPG storage facility failure, facility design philosophy, operating and maintenance procedures, and various fire-protection and firefighting approaches and presentations. The storage facilities covered are LPG installations (storage vessels and associated loading/unloading/transfer systems) at marine and pipeline terminals, natural gas processing plants, refineries, petrochemical plants, and tank farms.

  14. Clean air program: Design guidelines for bus transit systems using liquefied petroleum gas (LPG) as an alternative fuel. Final report, July 1995-April 1996

    SciTech Connect (OSTI)

    Raj, P.K.; Hathaway, W.T.; Kangas, R.

    1996-09-01

    The Federal Transit Administration (FTA) has initiated the development of `Design Guidelines for Bus Transit Systems Using Alternative Fuels.` This report provides design guidelines for the safe uses of Liquefied Petroleum Gas (LPG). It forms a part of the series of individual monographs being published by the FTA on (the guidelines for the safe use of) Compressed Natural Gas (CNG), Liquefied Natural Gas (LNG), Liquefied Petroleum Gas (LPG) and alcohol fuels (Methanol and Ethanol). Each report in this series describes for the subject fuel the important fuel properties, guidelines for the design and operation of bus fueling, storage and maintenance facilities, issues on personnel training and emergency preparedness.

  15. X-ray photoelectron spectroscopy studies on Pd doped SnO{sub 2} liquid petroleum gas sensor

    SciTech Connect (OSTI)

    Phani, A.R.

    1997-10-01

    The present investigation deals with the electrical response of palladium doped tin oxide, as a means of improving the selectivity for liquid petroleum gas (LPG) in the presence of CO, CH{sub 4}. The sensor element with the composition of Pd(1.5 wt{percent}) in the base material SnO{sub 2} sintered at 800{degree}C, has shown a high sensitivity towards LPG with a negligible cross interference of CO and CH{sub 4} at an operating temperature of 350{degree}C. This greatly suggests the possibility of utilizing the sensor for the detection of LPG. X-ray photoelectron spectroscopy studies have been carried out to determine the possible chemical species involved in the gas-solid interaction and the enhancing mechanism of the Pd doped SnO{sub 2} sensor element, towards LPG sensitivity. {copyright} {ital 1997 American Institute of Physics.}

  16. Make aromatics from LPG

    SciTech Connect (OSTI)

    Doolan, P.C. ); Pujado, P.R. )

    1989-09-01

    Liquefied petroleum gas (LPG) consists mainly of the propane and butane fraction recovered from gas fields, associated petroleum gas and refinery operations. Apart from its use in steam cracking and stream reforming, LPG has few petrochemical applications. The relative abundance of LPG and the strong demand for aromatics - benzene, toluene and xylenes (BTX) - make it economically attractive to produce aromatics via the aromatization of propane and butanes. This paper describes the Cyclar process, which is based on a catalyst formulation developed by BP and which uses UOP's CCR catalyst regeneration technology, converts propane, butanes or mixtures thereof to petrochemical-quality aromatics in a single step.

  17. Dehydrocyclodimerization, converting LPG to aromatics

    SciTech Connect (OSTI)

    Johnson, J.A.; Hilder, G.K.

    1984-03-01

    British Petroleum (BP) recognized the potential need for ways of exploiting feedstocks with low opportunity cost and commenced a research program at its Sunbury Research Center to discover and develop a catalyst for the conversion of LPG to a liquid product. The successful outcome of this research program is the Cyclar /SUP SM/ process, a joint development of UOP Process Division and British Petroleum. The Cyclar process offers a single-step conversion of LPG to an aromatic product which has a highvalue, is easily transported and useful both to fuel and petrochemical applications. The LPG producer can invest in a single unit, avoiding the need to identify and develop markets for multiple C/sub 3/ and C/sub 4/ products. This catalytic process, which employs UOP Continuous Catalyst Regeneration (CCR) technology, can also be applied to refinery light ends to produce a high-quality gasoline. Aromatic and hydrogen yields from propane and butane feeds surpass those obtained from catalytic reforming of Light Arabian naphtha. This paper describes the principles of the Cyclar process and illustrates yields and economics for several interesting applications.

  18. LPG emergency response training

    SciTech Connect (OSTI)

    Dix, R.B.; Newton, B.

    1995-12-31

    ROVER (Roll Over Vehicle for Emergency Response) is a specially designed and constructed unit built to allow emergency response personnel and LPG industry employees to get ``up close and personal`` with the type of equipment used for the highway transportation of liquefied petroleum gas (LPG). This trailer was constructed to simulate an MC 331 LPG trailer. It has all the valves, piping and emergency fittings found on highway tankers. What makes this unit different is that it rolls over and opens up to allow program attendees to climb inside the trailer and see it in a way they have never seen one before. The half-day training session is composed of a classroom portion during which attendees will participate in a discussion of hazardous material safety, cargo tank identification and construction. The specific properties of LPG, and the correct procedures for dealing with an LPG emergency. Attendees will then move outside to ROVER, where they will participate in a walkaround inspection of the rolled over unit. All fittings and piping will be representative of both modern and older equipment. Participants will also be able to climb inside the unit through a specially constructed hatch to view cutaway valves and interior construction. While the possibility of an LPG emergency remains remote, ROVER represents Amoco`s continuing commitment to community, education, and safety.

  19. LPG fuel supply system. [Patent for automotive

    SciTech Connect (OSTI)

    Pierson, W.V.

    1982-09-07

    A fuel supply system for an internal combustion engine operated on gaseous fuels, for example, liquid petroleum gas (Lpg). The system includes a housing having a chamber for vaporizing liquid gas, including means for heating the vaporizing chamber. Also included in the housing is a mixing chamber for mixing the vaporized gas with incoming air for delivery to the intake manifold of an internal combustion engine through a standard carburetor. The fuel supply system includes means for mounting the system on the carburetor, including means for supporting an air filter circumjacent the mixing chamber.

  20. New LPG loss-control standards

    SciTech Connect (OSTI)

    Blomquist, D.L. )

    1988-12-01

    API'S (American Petroleum Institute) Committee on Liquified Hydrocarbon Gas and the Committee and Safety and Fire Protection have modified Standard 2510 and added a supplemental Standard 2510A, in response to bad LPG incidents. Requirements have been tightened, with a major objective to prevent LPG releases. Fire protection Standards for the design and operation of LPG facilities are specifically revised. Following important changes are specifically discussed: Versel design, site selection, spacing and impounding; foundations and supports; and piping requirements.

  1. LPG storage vessel cracking experience

    SciTech Connect (OSTI)

    Cantwell, J.E. )

    1988-10-01

    In order to evaluate liquefied petroleum gas (LPG) handling and storage hazards, Caltex Petroleum Corp. (Dallas) surveyed several installations for storage vessel cracking problems. Cracking was found in approximately one-third of the storage vessels. In most cases, the cracking appeared to be due to original fabrication problems and could be removed without compromising the pressure containment. Several in-service cracking problems found were due to exposure to wet hydrogen sulfide. Various procedures were tried in order to minimize the in-service cracking potential. One sphere was condemned because of extensive subsurface cracking. This article's recommendations concern minimizing cracking on new and existing LPG storage vessels.

  2. Risks of LNG and LPG. [Review

    SciTech Connect (OSTI)

    Fay, J.A.

    1980-01-01

    Since the use of liquefied natural gas (LNG) and liquefied petroleum gases (LPG) as fuels is likely to increase and will certainly persist for some time to come, assessment of the safety of LNG/LPG systems will continue to draw attention and is quite likely to force continuing review of operating and design standards for LNG/LPG facilities. Scientific investigations to date appear to have identified the major hazards. Except for the dispersive behavior of vapor clouds - a not-insignificant factor in risk evaluation - the consequences of spills are well circumscribed by current analyses. The physically significant effects accompanying nonexplosive combustion of spilled material are fairly well documented; yet, potentially substantial uncertainties remain. Catastrophic spills of 10/sup 4/-10/sup 5/ m/sup 3/ on land or water are possible, given the current size of storage vessels. Almost all experimental spills have used less than 10 m/sup 3/ of liquid. There is thus some uncertainty regarding the accuracy and validity of extrapolation of current empirical information and physical models to spills of catastrophic size. The less-likely but still-possible explosive or fireball combustion modes are not well understood in respect to their inception. The troubling experience with such violent combustion of similar combustible vapors suggests that this possibility will need further definition. Extant LNG and LPG risk analyses illustrate the difficulties of substantiating the numerous event probabilities and the determination of all event sequences that can lead to hazardous consequences. Their disparate results show that significant improvements are needed. Most importantly, a detailed critique of past efforts and a determination of an exhaustive set of criteria for evaluating the adequacy of a risk analysis should precede any further attempts to improve on existing studies. 44 references, 1 table.

  3. Thermodynamic properties of liquefied petroleum gases (LPG). Interim report 15 Aug 75-31 Jan 77 (final)

    SciTech Connect (OSTI)

    Sallet, D.W.; Wu, K.F.

    1980-04-01

    The thermodynamic properties of several liquefied petroleum gases (with particular emphasis on propane) are discussed in detail. It is concluded that the widely used propane data by Stearns and George are too inconsistent and too inaccurate to be used for mass flow calculations of propane and propane mixtures through safety valves of rail tank cars. Accordingly, the thermodynamic properties of propane, propylene, n-butane, and a mixture of 65% (by mole) propane, 25% propylene, and 10% n-butane are recalculated using equations of states proposed by Benedict-Webb-Rubin (BWR) and by Starling. It is shown that Starling's equation results in thermodynamic properties which are more consistent and compare better with measured values than the BWR equation. Thermodynamic data for the four liquefied petroleum gases discussed above are calculated and presented in tabular form. In addition, predictions of pure propane mass flow rates (based upon isentropic), homogeneous equilibrium flow) are given. The influence of the thermodynamic data upon the predicted mass flow rates is demonstrated.

  4. International Energy Outlook 2016-Petroleum and other liquid fuels - Energy

    Gasoline and Diesel Fuel Update (EIA)

    Information Administration 2. Petroleum and other liquid fuels print version Overview In the International Energy Outlook 2016 (IEO2016) Reference case, worldwide consumption of petroleum and other liquid fuels increases from 90 million barrels per day (b/d) in 2012 to 100 million b/d in 2020 and 121 million b/d in 2040. Much of the growth in world liquid fuels consumption is projected for the emerging, non-Organization for Economic Cooperation and Development (non-OECD) economies of Asia,

  5. Numerical Simulations of Leakage from Underground LPG Storage Caverns

    SciTech Connect (OSTI)

    Yamamoto, Hajime; Pruess, Karsten

    2004-09-01

    To secure a stable supply of petroleum gas, underground storage caverns for liquified petroleum gas (LPG) are commonly used in many countries worldwide. Storing LPG in underground caverns requires that the surrounding rock mass remain saturated with groundwater and that the water pressure be higher than the liquid pressure inside the cavern. In previous studies, gas containment criteria for underground gas storage based on hydraulic gradient and pressure have been discussed, but these studies do not consider the physicochemical characteristics and behavior of LPG such as vaporization and dissolution in groundwater. Therefore, while these studies are very useful for designing storage caverns, they do not provide better understanding of the either the environmental effects of gas contamination or the behavior of vaporized LPG. In this study, we have performed three-phase fluid flow simulations of gas leakage from underground LPG storage caverns, using the multiphase multicomponent nonisothermal simulator TMVOC (Pruess and Battistelli, 2002), which is capable of solving the three-phase nonisothermal flow of water, gas, and a multicomponent mixture of volatile organic chemicals (VOCs) in multidimensional heterogeneous porous media. A two-dimensional cross-sectional model resembling an actual underground LPG facility in Japan was developed, and gas leakage phenomena were simulated for three different permeability models: (1) a homogeneous model, (2) a single-fault model, and (3) a heterogeneous model. In addition, the behavior of stored LPG was studied for the special case of a water curtain suddenly losing its function because of operational problems, or because of long-term effects such as clogging of boreholes. The results of the study indicate the following: (1) The water curtain system is a very powerful means for preventing gas leakage from underground storage facilities. By operating with appropriate pressure and layout, gas containment can be ensured. (2

  6. Cause not found for Texas LPG site blast

    SciTech Connect (OSTI)

    Not Available

    1992-04-20

    This paper reports that National Transportation Safety Board investigators completed the first phase of tests at Seminole Pipeline Co.'s liquid petroleum gas storage dome near Brenham, Tex., without finding the cause of an explosion there Apr. 7. But in a week of investigation, NTSB determined that a release of brine and product occurred at the 350,000 bbl LPG storage dome, about 45 miles northwest of Houston, just before the blast. The explosion sent shock waves felt as far as 130 miles away. Three persons have died from injuries suffered in the accident. Another 18 were injured.

  7. A simple correlation to predict the hydrate quadruple point temperature for LPG mixtures

    SciTech Connect (OSTI)

    Yousif, M.H.

    1997-12-31

    A simple correlation to predict the hydrate upper quadruple point temperature, T{sub Q2B} for liquefied petroleum gas (LPG) mixtures was developed. It was developed for use as a part of a modeling and control system for a LPG pipeline in Russia. For performance reasons, a simple hydrate prediction correlation was required that could be incorporated into the real-time and predictive pipeline simulation models. The operating company required both real time and predictive simulation tools be developed to assist in preventing hydrate blockages while minimizing the use of methanol. In this particular pipeline, LPG fluid moves through the pipeline as a single phase liquid above its bubble point pressure. Because of the very low flow rates, the trace amount of water present in the LPG drops out and creates water pools at low points in the pipeline. The pipeline pressure and seasonal temperatures are conducive for hydrate formation in these pools. Methanol and monoethylene glycol (MEG) are injected in the pipeline to help prevent hydrate formation. The newly developed correlation predicts the hydrate quadruple point temperature using only the composition and the molecular weight of the LPG mixture while retaining an accuracy comparable to the statistical thermodynamic models throughout the range of normal operating conditions.

  8. Emissions from ethanol and LPG fueled vehicles

    SciTech Connect (OSTI)

    Pitstick, M.E.

    1992-01-01

    This paper addresses the environmental concerns of using neat ethanol and liquified petroleum gas (LPG) as transportation fuels in the US Low-level blends of ethanol (10%) with gasoline have been used as fuels in the US for more than a decade, but neat ethanol (85% or more) has only been used extensively in Brazil. LPG, which consists mostly of propane, is already used extensively as a vehicle fuel in the US, but its use has been limited primarily to converted fleet vehicles. Increasing US interest in alternative fuels has raised the possibility of introducing neat ethanol vehicles into the market and expanding the number of LPG vehicles. Use of such vehicles and increased production and consumption of fuel ethanol and LPG will undoubtedly have environmental impacts. If the impacts are determined to be severe, they could act as barriers to the introduction of neat ethanol and LPG vehicles. Environmental concerns include exhaust and evaporative emissions and their impact on ozone formation and global warming, toxic emissions from fuel combustion and evaporation, and agricultural emissions from production of ethanol. The paper is not intended to be judgmental regarding the overall attractiveness of ethanol or LPG compared to other transportation fuels. The environmental concerns are reviewed and summarized, but the only conclusion reached is that there is no single concern that is likely to prevent the introduction of neat ethanol fueled vehicles or the increase in LPG fueled vehicles.

  9. Emissions from ethanol and LPG fueled vehicles

    SciTech Connect (OSTI)

    Pitstick, M.E.

    1992-12-31

    This paper addresses the environmental concerns of using neat ethanol and liquified petroleum gas (LPG) as transportation fuels in the US Low-level blends of ethanol (10%) with gasoline have been used as fuels in the US for more than a decade, but neat ethanol (85% or more) has only been used extensively in Brazil. LPG, which consists mostly of propane, is already used extensively as a vehicle fuel in the US, but its use has been limited primarily to converted fleet vehicles. Increasing US interest in alternative fuels has raised the possibility of introducing neat ethanol vehicles into the market and expanding the number of LPG vehicles. Use of such vehicles and increased production and consumption of fuel ethanol and LPG will undoubtedly have environmental impacts. If the impacts are determined to be severe, they could act as barriers to the introduction of neat ethanol and LPG vehicles. Environmental concerns include exhaust and evaporative emissions and their impact on ozone formation and global warming, toxic emissions from fuel combustion and evaporation, and agricultural emissions from production of ethanol. The paper is not intended to be judgmental regarding the overall attractiveness of ethanol or LPG compared to other transportation fuels. The environmental concerns are reviewed and summarized, but the only conclusion reached is that there is no single concern that is likely to prevent the introduction of neat ethanol fueled vehicles or the increase in LPG fueled vehicles.

  10. Catalytic conversion of LPG

    SciTech Connect (OSTI)

    Pujado, P.R.; Vora, B.V.; Mowry, J.R.; Anderson, R.F.

    1986-01-01

    The low reactivity of light paraffins has long hindered their utilization as petrochemical feedstocks. Except for their use in ethylene crackers, LPG fractions have traditionally been consumed as fuel. New catalytic processes now being commercialized open new avenues for the utilization of LPG as sources of valuable petrochemical intermediates. This paper discusses processes for the dehydrogenation and aromatization of LPG.

  11. Determination of usage patterns and emissions for propane/LPG in California. Final report

    SciTech Connect (OSTI)

    Sullivan, M.

    1992-05-01

    The purpose of the study was to determine California usage patterns of Liquified Petroleum Gas (LPG), and to estimate propane emissions resulting from LPG transfer operations statewide, and by county and air basin. The study is the first attempt to quantify LPG transfer emissions for California. This was accomplished by analyzing data from a telephone survey of California businesses that use LPG, by extracting information from existing databases.

  12. Nonresidential buildings energy consumption survey: 1979 consumption and expenditures. Part 2. Steam, fuel oil, LPG, and all fuels

    SciTech Connect (OSTI)

    Patinkin, L.

    1983-12-01

    This report presents data on square footage and on total energy consumption and expenditures for commercial buildings in the contiguous United States. Also included are detailed consumption and expenditures tables for fuel oil or kerosene, liquid petroleum gas (LPG), and purchased steam. Commercial buildings include all nonresidential buildings with the exception of those where industrial activities occupy more of the total square footage than any other type of activity. 7 figures, 23 tables.

  13. LPG in Venezuela

    SciTech Connect (OSTI)

    Romero, O.

    1986-01-01

    The use of LPG for domestic consumption in Venezuela began in late 1929 when LPG was imported in lots of 500 cylinders. These cylinders were then returned to the U.S. for refilling. Total consumption at that time was some 40M/sup 3/ (250 barrels) per year and by 1937 had grown to some 540M/sup 3/ (3,400 barrels) per year. Local production of LPG from gas began in the mid thirties with a small cooling plant in the Mene Grande Field in the Lake Maracaibo area, the first field to produce oil in Venezuela (1914). This plant produced gasoline for a refinery and some of the first LPG used in Venezuela for domestic consumption. The capacity of this plant was insufficient to satisfy the growing demand for LPG which was supplied from refinery production until the development of the natural gas processing industry. At the present time, Venezuelan refineries are net consumers of LPG.

  14. Custody transfer measurements for LNG/LPG

    SciTech Connect (OSTI)

    Williams, R.A.

    1984-04-01

    The buying, selling, and transportation of Liquefied Natural Gas (LNG) and Liquefied Petroleum Gas (LPG) requires the use of sophisticated measurement systems for accurate determination of the total quantity and energy content for custody transfer reporting and safe cargo handling of these cryogenic products. These systems must meet strict safety standards for operation in a hazardous environment and, at the same time, provide accurate, reliable information for the storage, transfer, and data reporting required for both operational and financial accounting purposes. A brief discussion of LNG and LPG characteristics and detailed description of these special measurement techniques are given in this presentation.

  15. LPG in Mexico

    SciTech Connect (OSTI)

    Miles, E.L.

    1986-01-01

    The authors review LPG in Mexico. They attempt to project numbers to the year 2000 using a supply/demand comparison.

  16. Monitoring system tested during LPG tanker unloading

    SciTech Connect (OSTI)

    Not Available

    1990-05-14

    A specially developed computer-based hazardous-materials monitoring system has been successfully field tested. The test of the portable system occurred during the unloading of 45,000 metric tons of LPG from a 740-ft tanker at the petroleum dock of a plant along the Mississippi River. The function of this system is to detect, report, alarm, and record unacceptable concentrations of hazardous vapors during marine-transfer operations.

  17. Simultaneous boiling and spreading of liquefied petroleum gas on water. Final report, December 12, 1978-March 31, 1981

    SciTech Connect (OSTI)

    Chang, H.R.; Reid, R.C.

    1981-04-01

    An experimental and theoretical investigation was carried out to study the boiling and spreading of liquid nitrogen, liquid methane and liquefied petroleum gas (LPG) on water in a one-dimensional configuration. Primary emphasis was placed on the LPG studies. Experimental work involved the design and construction of a spill/spread/boil apparatus which permitted the measurement of spreading and local boil-off rates. With the equations of continuity and momentum transfer, a mathematical model was developed to describe the boiling-spreading phenomena of cryogens spilled on water. The model accounted for a decrease in the density of the cryogenic liquid due to bubble formation. The boiling and spreading rates of LPG were found to be the same as those of pure propane. An LPG spill was characterized by the very rapid and violent boiling initially and highly irregular ice formation on the water surface. The measured local boil-off rates of LPG agreed reasonably well with theoretical predictions from a moving boundary heat transfer model. The spreading velocity of an LPG spill was found to be constant and determined by the size of the distributor opening. The maximum spreading distance was found to be unaffected by the spilling rate. These observations can be explained by assuming that the ice formation on the water surface controls the spreading of LPG spills. While the mathematical model did not predict the spreading front adequately, it predicted the maximum spreading distance reasonably well.

  18. Jet fuel from LPG

    SciTech Connect (OSTI)

    Maples, R.E.; Jones, J.R.

    1983-02-01

    Explains how jet fuel can be manufactured from propane and/or butane with attractive rates of return. This scheme is advantageous where large reserves of LPG-bearing gas is available or LPG is in excess. The following sequence of processes in involved: dehydrogenation of propane (and/or butane) to propylene (and/or butylene); polymerization of this monomer to a substantial yield of the desired polymer by recycling undesired polymer; and hydrotreating the polymer to saturate double bonds. An attribute of this process scheme is that each of the individual processes has been practiced commercially. The process should have appeal in those parts of the world which have large reserves of LPG-bearing natural gas but little or no crude oil, or where large excesses of LPG are available. Concludes that economic analysis shows attractive rates of return in a range of reasonable propane costs and product selling prices.

  19. Fire safety of LPG in marine transportation

    SciTech Connect (OSTI)

    Martinsen, W.E.; Johnson, D.W.; Welker, J.R.

    1980-08-01

    This report contains an analytical examination of cargo spill and fire hazard potential associated with the marine handling of liquefied petroleum gas (LPG) as cargo. Principal emphasis was on cargo transfer operations for ships unloading at receiving terminals, and barges loading or unloading at a terminal. Major safety systems, including emergency shutdown systems, hazard detection systems, and fire extinguishment and control systems were included in the analysis. Spill probabilities were obtained from fault tree analyses utilizing composite LPG tank ship and barge designs. Failure rates for hardware in the analyses were generally taken from historical data on similar generic classes of hardware, there being very little historical data on the specific items involved. Potential consequences of cargo spills of various sizes are discussed and compared to actual LPG vapor cloud incidents. The usefulness of hazard mitigation systems (particularly dry chemical fire extinguishers and water spray systems) in controlling the hazards posed by LPG spills and spill fires is also discussed. The analysis estimates the probability of fatality for a terminal operator is about 10/sup -6/ to 10/sup -5/ per cargo transfer operation. The probability of fatality for the general public is substantially less.

  20. Emissions from ethanol- and LPG-fueled vehicles

    SciTech Connect (OSTI)

    Pitstick, M.E.

    1995-06-01

    This paper addresses the environmental concerns of using neat ethanol and liquefied petroleum gas (LPG) as transportation fuels in the United States. Low-level blends of ethanol (10%) with gasoline have been used as fuels in the United States for more than a decade, but neat ethanol (85% or more) has only been used extensively in Brazil. LPG, which consists mostly of propane, is already used extensively as a vehicle fuel in the United States, but its use has been limited primarily to converted fleet vehicles. Increasing U.S. interest in alternative fuels has raised the possibility of introducing neat-ethanol vehicles into the market and expanding the number of LPG vehicles. Use of such vehicles, and increased production and consumption of fuel ethanol and LPG, will undoubtedly have environmental impacts. If the impacts are determined to be severe, they could act as barriers to the introduction of neat-ethanol and LPG vehicles. Environmental concerns include exhaust and evaporative emissions and their impact on ozone formation and global warming, toxic emissions from fuel combustion and evaporation, and agricultural impacts from production of ethanol. The paper is not intended to be judgmental regarding the overall attractiveness of ethanol or LPG as compared with other transportation fuels. The environmental concerns are reviewed and summarized, but only conclusion reached is that there is no single concern that is likely to prevent the introduction of neat-ethanol-fueled vehicles or the increase in LPG-fueled vehicles.

  1. Petroleum & Other Liquids - U.S. Energy Information Administration (EIA)

    U.S. Energy Information Administration (EIA) Indexed Site

    Petroleum & Other Liquids Glossary › FAQS › Overview Data Summary Prices Crude reserves and production Refining and processing Imports/exports & movements Stocks Consumption/sales All petroleum & other liquids data reports Analysis & Projections Major Topics Most popular Consumption & sales Crude reserves & production Imports/exports & movements Prices Projections Recurring Refining & processing Stocks All reports Browse by Tag Alphabetical Frequency Tag Cloud

  2. Blast rips Texas LPG storage site

    SciTech Connect (OSTI)

    Not Available

    1992-04-13

    This paper reports that Seminole Pipeline Co. at presstime last week had planned to reopen its 775 mile liquefied petroleum gas pipeline in South Texas by Apr. 12 after a huge explosion devastated the area around a Seminole LPG storage salt dome near Brenham, Tex., forcing the pipeline shutdown. A large fire was still burning at the storage site at presstime last week. The blast - shortly after 7 a.m. Apr. 7 - occurred at a pipeline connecting the main Seminole line with the storage facility and caused shock waves felt 130 miles away. A 5 year old boy who lived in a trailer near Seminole's LPG storage dome was killed, and 20 persons were injured.

  3. Demand for petrochem feedstock to buoy world LPG industry

    SciTech Connect (OSTI)

    Not Available

    1992-05-18

    This paper reports that use of liquefied petroleum gas as petrochemical feedstock will increase worldwide, providing major growth opportunities for LPG producers. World exports of liquefied petroleum gas will increase more slowly than production as producers choose to use LPG locally as chemical feedstock and export in value added forms such as polyethylene. So predicts Poten and Partners Inc., New York. Poten forecasts LPG production in exporting countries will jump to 95 million tons in 2010 from 45 million tons in 1990. However, local and regional demand will climb to 60 million tons/year from 23 million tons/year during the same period. So supplies available for export will rise to 35 million tons in 2010 from 22 million tons in 1990.

  4. Accurate LPG analysis begins with sampling procedures, equipment

    SciTech Connect (OSTI)

    Wilkins, C.M. )

    1990-11-05

    Proper equipment and procedures are essential for obtaining representative samples from an LPG stream. This paper discusses how sampling of light liquid hydrocarbons generally involves one of two methods: flow- proportional composite sampling by a mechanical device or physical transfer of hydrocarbon fluids from a flowing pipeline or other source into a suitable portable sample container. If sampling by proper techniques and equipment supports careful chromatographic analysis, full advantage of accurate mass measurement of LPG can be realized.

  5. Mounded LPG storage - Experience and developments

    SciTech Connect (OSTI)

    Barber, D.

    1988-01-01

    Liquefied petroleum gas (LPG) is stored after production, and for distribution and use, in pressure vessels which vary in size from a few kilogrammes to many thousands of tons. The types of LPG under consideration are commercial butane, commercial propane, or mixtures of the two gases in varying proportions. Mounded storage systems are becoming popular as an alternative to the better-known traditional systems. The most widely used and therefore best-known of the traditional systems are the above-ground pressure-vessel designs. These more commonly comprise factory-made cylinders which are installed horizontally, being supported on saddles at each end of the vessel. When such vessels are installed in an LPG terminal, depot, or filling plant, they are required in multiple units to facilitate the storage of more than one grade of product and to enable regular maintenance and inspection to be carried out. Today's safety regulations require such installations to be divided into sub-groups of six tanks, with all the tanks located at a safe distance from one another, and from other facilities in the immediate area. These safety distances are being increased as a result of experience, which means terminals now require large areas of land.

  6. LPG fuel shutoff system

    SciTech Connect (OSTI)

    Watanabe, T.; Miyata, K.

    1988-01-26

    An LPG fuel shutoff system for use with a vehicle having an LPG fuel engine and having a solenoid valve to supply and shut off LPG fuel is described including: a relay having a relay contact which is closed when an electric current is fed to a coil of the relay; a pressure switch having a first position and a second position and adapted to be in the first position when engine oil pressure rises above a predetermined level; and an oil lamp adapted to light when the engine oil pressure is below the predetermined level, and wherein a solenoid coil of the solenoid valve is connected at one side to a battery through an ignition switch and a fuel switch. The solenoid coil also is connected, at another side of the solenoid coil, in series to the relay contact and the pressure switch in the second position respectively, the coil of the relay is connected to the solenoid valve side of the ignition switch through a starting switch, the oil lamp is connected between the ignition switch and the pressure switch.

  7. Experience with Bi-Fuel LPG Pickups in Texas

    SciTech Connect (OSTI)

    Whalen, P.

    1999-05-12

    The State of Texas requires state agencies to purchase alternative fuel vehicles (AFVs). In 1996, Texas Department of Transportation (TxDOT) representatives added about 400 bi-fuel liquefied petroleum gas (LPG) pickup trucks to their fleet. The fleet managers were willing to share information about their fleets and the operation of these vehicles, so a study was launched to collect operations, maintenance, and cost data for selected LPG and gasoline vehicles (as controls) throughout 18 months of vehicle operation. This case study presents the results of that data collection and its subsequent analysis.

  8. Petroleum: An energy profile, 1999

    SciTech Connect (OSTI)

    1999-07-01

    This report prepared by the Energy Information Administration covers the following topics: petroleum production and end-use sectors; resources and reserves; exploration and production; LPG sources and processing; motor gasoline octane enhancement; constructing pipelines; the strategic petroleum reserve; imports and exports; marketing; district descriptions and maps; and refinery processes and facilities. 33 figs., 7 tabs.

  9. Control and extinguishment of LPG fires. Final report

    SciTech Connect (OSTI)

    Johnson, D.W.; Martinsen, W.E.; Cavin, W.D.; Chilton, P.D.; Lawson, H.P.; Welker, J.R.

    1980-08-01

    Approximately 100 fire control and fire extinguishment tests were run on free-burning liquefied petroleum gases (LPG) pool fires from 25 ft/sup 2/ to 1600 ft/sup 2/ in area. The LPG was contained in concrete pits, and the pit floors were allowed to cool before the fires were ignited so that the burning rates were not influenced by boiloff from the warm floor. High expansion foam was used for fire control. The foam was applied from fixed generators located on the upwind side of the pit. Fires were controlled after foam application of less than a minute to about 10 minutes, depending on the application rate. Fires were extinguished with dry chemical agents applied through fixed piping systems with tankside nozzles and by manual application using hoselines and portable extinguishers. Fires could readily be extinguished in times ranging from a few seconds to about half a minute, depending on the application rate, system design, and ambient conditions. Additional tests were conducted in 1-ft/sup 2/ and 5-ft/sup 2/ pits to determine the boiloff rates for LPG spilled on concrete, a sand/soil mix, and polyurethane foam substrates. Burning rates for free-burning LPG pool fires from 1 ft/sup 2/ to 1600 ft/sup 2/ in area are also reported.

  10. Fire safety of LPG in marine transportation. Final report

    SciTech Connect (OSTI)

    Martinsen, W.E.; Johnson, D.W.; Welker, J.R.

    1980-06-01

    This report contains an analytical examination of cargo spill and fire hazard potential associated with the marine handling of liquefied petroleum gas (LPG) as cargo. Principal emphasis was on cargo transfer operations for ships unloading at receiving terminals, and barges loading or unloading at a terminal. Major safety systems, including emergency shutdown systems, hazard detection systems, and fire extinguishment and control systems were included in the analysis. Spill probabilities were obtained from fault tree analyses utilizing composite LPG tank ship and barge designs. Failure rates for hardware in the analyses were generally taken from historical data on similar generic classes of hardware, there being very little historical data on the specific items involved. Potential consequences of cargo spills of various sizes are discussed and compared to actual LPG vapor cloud incidents. The usefulness of hazard mitigation systems (particularly dry chemical fire extinguishers and water spray systems) in controlling the hazards posed by LPG spills and spill fires is also discussed. The analysis estimates the probability of fatality for a terminal operator is about 10/sup -6/ to 10/sup -5/ per cargo transfer operation. The probability of fatality for the general public is substantially less.

  11. Influence of H{sub 2}O{sub 2} on LPG fuel performance evaluation

    SciTech Connect (OSTI)

    Khan, Muhammad Saad Ahmed, Iqbal Mutalib, Mohammad Ibrahim bin Abdul Nadeem, Saad Ali, Shahid

    2014-10-24

    The objective of this mode of combustion is to insertion of hydrogen peroxide (H{sub 2}O{sub 2}) to the Liquefied Petroleum Gas (LPG) combustion on spark plug ignition engines. The addition of hydrogen peroxide may probably decrease the formation of NO{sub x}, CO{sub x} and unburned hydrocarbons. Hypothetically, Studies have shown that addition of hydrogen peroxide to examine the performance of LPG/H{sub 2}O{sub 2} mixture in numerous volumetric compositions starting from lean LPG until obtaining a better composition can reduce the LPG fuel consumption. The theory behind this idea is that, the addition of H{sub 2}O{sub 2} can cover the lean operation limit, increase the lean burn ability, diminution the burn duration along with controlling the exhaust emission by significantly reducing the greenhouse gaseous.

  12. The SONATRACH jumbo LPG plant

    SciTech Connect (OSTI)

    Ahmed Khodja, A.; Bennaceur, A.

    1988-01-01

    The authors aim is to give to the 17 TH world gas conference a general idea on SONATRACH LPG PLANT which is located in the ARZEW area. They develop this communication as follows: general presentation of LPG plant: During the communication, the author's will give the assistance all the information concerning the contractions the erection's date and the LPG PLANT process, start-up of the plant: In this chapter, the authors's will describe the start-up condition, the performance test result, the flexibility test result and the total mechanical achievement of the plant; operation by SONATRACH: After the success that obtained during the mechanical achievement and performance test, the contractor handed over the plant to SONATRACH.

  13. LPG storage vessel cracking experience

    SciTech Connect (OSTI)

    Cantwell, J.E.

    1988-01-01

    As part of an overall company program to evaluate LPG handling and storage hazards the authors surveyed several installations for storage vessel cracking problems. Cracking was found in approximately one third of the storage vessels. In most cases the cracking appeared due to original fabrication problems and could be removed without compromising the pressure containment. Several in-service cracking problems due to exposure to wet hydrogen sulfide were found. Various procedures were tried in order to minimize the in-service cracking potential. One sphere was condemned because of extensive subsurface cracking. Recommendations are made to minimize cracking on new and existing LPG storage vessels.

  14. Industrial cooperation in the field of LPG

    SciTech Connect (OSTI)

    Stefano, M.; Trollux, J.; Dune, J.J.

    1988-01-01

    The years to come should confirm the availability of LPG worldwide and enable future users in developing countries to satisfy energy requirements which today are only partly covered, if at all. This paper is designed to point the benefits that these new LPG markets could derive from active cooperation with experienced companies operating in mature LPG markets.

  15. Carbon adsorption system protects LPG storage sphere

    SciTech Connect (OSTI)

    Gothenquist, C.A.; Rooker, K.M.

    1996-07-01

    Chevron U.S.A. Products Co. installed a carbon adsorption system to protect an LPG storage sphere at its refinery in Richmond, Calif. Vessel damage can result when amine contamination leads to emulsion formation and consequent amine carry-over, thus promoting wet-H{sub 2}S cracking. In Chevron`s No. 5 H{sub 2}S recovery plant, a mixture of butane and propane containing H{sub 2}S is contacted with diethanolamine (DEA) in a liquid-liquid absorber. The absorber is a countercurrent contactor with three packed beds. Because the sweetening system did not include a carbon adsorption unit for amine purification, contaminants were building up in the DEA. The contaminants comprised: treatment chemicals, hydrocarbons, foam inhibitors, and amine degradation products. The paper describes the solution to this problem.

  16. Utilization of LPG for vehicles in Japan

    SciTech Connect (OSTI)

    Kusakabe, M.; Makino, M.; Tokunoh, M.

    1988-01-01

    LPG demand for vehicles amounts to 1.8 MM tons annually, equivalent to about 11% of the total LPG consumption in Japan. The feature which dominates the demand of LPG as a vehicle fuel in Japan is the high penetration of LPG powered vehicles into taxi fleets. This has been made possible following the rationalization in the taxi business in the early 1960s. Today, three quarters of LPG vehicles, numbering some 235,000 while representing only about 1% of the total number of vehicles, account for nearly 93% of all taxicabs.

  17. Technical evaluation and assessment of CNG/LPG bi-fuel and flex-fuel vehicle viability

    SciTech Connect (OSTI)

    Sinor, J E

    1994-05-01

    This report compares vehicles using compressed natural gas (CNG), liquefied petroleum gas (LPG), and combinations of the two in bi-fuel or flex-fuel configurations. Evidence shows that environmental and energy advantages can be gained by replacing two-fuel CNG/gasoline vehicles with two-fuel or flex-fuel systems to be economically competitive, it is necessary to develop a universal CNG/LPG pressure-regulator-injector and engine control module to switch from one tank to the other. For flex-fuel CNG/LPG designs, appropriate composition sensors, refueling pumps, fuel tanks, and vaporizers are necessary.

  18. Process for LPG recovery

    SciTech Connect (OSTI)

    Khan, S.A.; Haliburton, J.

    1990-10-30

    This patent describes an improvement in a process for separating propane and heavier hydrocarbons from a gaseous feedstream containing hydrocarbon components of different boiling points wherein the feedstream is cooled and separated into a first vapor fraction and a first liquid fraction and the first liquid fraction is distilled in a deethanizer to form a second vapor fraction and a second liquid fraction. The improvement comprises expanding and transferring the first vapor fraction to the lower portion of a direct heat exchanger, cooling {ital at least a portion of} the second vapor fraction {ital by passing it through an indirect heat exchanger} to form a substantially liquefied stream, {ital partially flashing at least a portion of the liquefied stream and transferring it} to the upper portion of the direct heat exchanger whereby the liquefied stream contacts the first vapor fraction to form a third vapor fraction and a third liquid fraction, {ital transferring} the third liquid fraction to the deethanizer, and removing the third vapor fraction from the direct heat exchanger {ital and passing the third vapor fraction through the indirect heat exchanger}.

  19. An analysis of weep holes as a product detection device for underground compensated LPG storage systems

    SciTech Connect (OSTI)

    Sarica, C.; Demir, H.M.; Brill, J.P.

    1996-09-01

    Weep holes have been used widely to detect the presence of Liquefied Petroleum Gases (LPG) in brine for underground compensated storage systems. When the brine level drops below the weep hole, LPG product enters the brine production system causing an increase in both tubing head pressure and flow rate. To prevent cavern overfill, a cavern shutdown is initiated upon detection of LPG in the surface brine system by pressure or flow instruments at the tubing head. In this study, we have investigated the multiphase flow characteristics of weep hole LPG detection systems to correctly estimate the operating limits. A simple and easy to use model has been developed to predict the tubing head pressure and flow rate increases. The model can be used to implement safer and more efficient operation procedures for underground compensated LPG storage systems. The model predictions for a typical field case are presented. An analysis of weep holes as product detection devices for LPG storage reservoirs has been carried out. It was found that the increases in pressure and flow rates at the tubing head change as a function of injection flow rate of the product. Therefore, a thorough consideration of cavern operating parameters is necessary to evaluate the use constant pressure and flow rate values to initiate emergency shut down of the cavern.

  20. Offshore refrigerated LPG loading/unloading terminal using a CALM buoy

    SciTech Connect (OSTI)

    Bonjour, E.L.; Simon, J.M.

    1985-03-01

    In existing Liquefied Petroleum Gases terminals, the transfer of liquefied gases to the tanker is performed via articulated loading arms or flexible hoses, working under quasistatic conditions. The tanker has to be firmly moored alongside a jetty or a process barge in a protected area (such as a harbour in most cases). This paper gives the main results of the development of an offshore refrigerated LPG (-48/sup 0/C) loading/unloading system, using a CALM buoy and LPG floating hoses working under dynamic conditions. The aim of this new concept is to replace the standard harbour structure for loading/unloading refrigerated LPG and to provide a considerable reduction in investments and a greater flexibility regarding the terminal location. The main components of that terminal have been designed so as to enable the loading of a 75 000 cubic meter LPG carrier in 15 hours. The results of static and dynamic low temperature tests on a LPG swivel joint for CALM buoy and LPG floating hoses show that such a SPM terminal is now a realistic solution.

  1. LPG land transportation and storage safety. Final report

    SciTech Connect (OSTI)

    Not Available

    1981-09-01

    This report contains an analytical examination of fatal accidents involving liquefied petroleum gas (LPG) releases during transportation and/or transportation related storage. Principal emphasis was on accidents during the nine-year period 1971 to 1979. Fatalities to members of the general public (i.e., those at the scene of the accident through coincidence or curiosity) were of special interest. Transportation accidents involving railroad tank cars, trucks, and pipelines were examined as were accidents at storage facilities, including loading and unloading at such facilities. The main sources of the necessary historical accident data were the accident reports submitted to the Department of Transportation by LPG carriers, National Transportation Safety Board accident reports, articles in the National Fire Protection Association journals, other literature, and personal interviews with firemen, company personnel, and others with knowledge of certain accidents. The data indicate that, on the average, releases of LPG during transportation and intermediate storage cause approximately six fatalities per year to members of the general public. The individual risk is about 1 death per 37,000,000 persons; about the same as the risk of a person on the ground being killed by an airplane crash, and much less than the risk of death by lightning, tornadoes, or dam failures.

  2. LPG land transportation and storage safety. Final report

    SciTech Connect (OSTI)

    Martinsen, W.E.; Cavin, W.D.

    1981-09-01

    This report contains an analytical examination of fatal accidents involving liquefied petroleum gas (LPG) releases during transportation and/or transportation related storage. Principal emphasis was on accidents during the nine-year period 1971 through 1979. Fatalities to members of the general public (i.e., those at the scene of the accident through coincidence or curiosity) were of special interest. Transportation accidents involving railroad tank cars, trucks, and pipelines were examined as were accidents at storage facilities, including loading and unloading at such facilities. The main sources of the necessary historical accident data were the accident reports submitted to the Department of Transportation by LPG carriers, National Transportation Safety Board accident reports, articles in the National Fire Protection Association journals, other literature, and personal interviews with firemen, company personnel, and others with knowledge of certain accidents. The data indicate that, on the average, releases of LPG during transportation and intermediate storage cause approximately six fatalities per year to members of the general public. The individual risk is about 1 death per 37,000,000 persons; about the same as the risk of a person on the ground being killed by an airplane crash, and much less than the risk of death by lightning, tornadoes, or dam failures.

  3. LPG Electrical, Inc | Open Energy Information

    Open Energy Info (EERE)

    LPG Electrical, Inc Jump to: navigation, search Name: ANGWIN Electrical Address: 13833 Wellington Trace Rd. 4 Place: Wellington, Florida Zip: 33414 Sector: Services Product:...

  4. Impact of foreign LPG operations on domestic LPG markets

    SciTech Connect (OSTI)

    Jones, C.

    1981-01-01

    During 1978 the federal government passed legislation allowing a major increase in natural gas prices and offering hope that some portion of the supply will be allowed to reach free market levels. The mechanism for decontrol of crude oil was also put into effect. This favorable government action and higher world oil prices have led to a major resurgence in domestic exploration. In addition to the supply effects, there appears to have been a substantial demand response to the latest round of world oil price increases. The purpose of this paper is to discuss how these events have affected domestic LPG markets and pricing.

  5. Refining and end use study of coal liquids. Topical report: Petroleum Refinery; Linear Programming Model; and Design Basis

    SciTech Connect (OSTI)

    1995-03-01

    A model was developed for use in the Bechtel PIMS (Process Industry Modeling System) linear programming software to simulate a generic Midwest (PADD II) petroleum refinery of the future. This ``petroleum-only`` version of the model establishes the size and complexity of the refinery after the year 2000 and prior to the introduction of coal liquids. It should be noted that no assumption has been made on when a plant can be built to produce coal liquids except that it will be after the year 2000. The year 2000 was chosen because it is the latest year where fuel property and emission standards have been set by the Environmental Protection Agency. It assumes the refinery has been modified to accept crudes that are heavier in gravity and higher in sulfur than today`s average crude mix. In addition, the refinery has also been modified to produce a product slate of transportation fuels of the future (i.e. 40% reformulated gasolines). This model will be used as a basis for determining the optimum scheme for processing coal liquids in a petroleum refinery. This report summarizes the design basis for this ``petroleum only`` LP refinery model. A report detailing the refinery configuration when coal liquids are processed will be provided at a later date.

  6. Table 5.1a Petroleum and Other Liquids Overview, 1949-2011

    U.S. Energy Information Administration (EIA) Indexed Site

    a Petroleum and Other Liquids Overview, 1949-2011 Year Production 1 Production as Share of Estimated Consumption Net Imports 2 Net Imports as Share of Estimated Consumption Balancing Item 3 Estimated Consumption 4 Thousand Barrels Percent Thousand Barrels Percent Thousand Barrels 1949 1,998,441 95.0 116,183 5.5 -11,115 2,103,509 1950 2,156,247 91.5 198,955 8.4 1,938 2,357,140 1951 2,455,113 95.9 154,142 6.0 -48,367 2,560,888 1952 2,515,903 94.6 190,319 7.2 -45,542 2,660,680 1953 2,602,845 93.8

  7. Separation of petroleum refinery wastes from a landfill by liquid chromatography

    SciTech Connect (OSTI)

    Mazzocco, D.L.; Willis, W.V.

    1995-12-01

    Large amounts of acidic petroleum refinery wastes (PRW) have been buried in landfills during the period 1930-1950. Many of the compounds IN PRW have not identified. Organosulfur compounds constitute an important fraction of these wastes, and are significant in site closure planning and cleanup operations. Some are difficult analytes because they undergo facile conversions during standard methods of sample preparation and analysis. A mild liquid chromatographic method using cyanopropyl and octadecyl stationary phases and a modified hexane mobile phase was found to separate PRW into five major groups, two of which contain sulfur compounds. GC/MS analysis of collected HPLC fractions identified over 80% of the compounds present. Wastes from three different landfills used in the period 1940-1950 show major similarities, but differ in relative composition. Implications for remediation of PRW in these and similar landfills designated as Superfund sites are discussed.

  8. LPG dealers, manufacturers report diverse effects of recession and war

    SciTech Connect (OSTI)

    Prowler, S.

    1991-01-01

    The author presents a survey of LPG marketers. The effects of the Persian Gulf War and U.S. recession on the LPG industry are discussed.

  9. Algeria LPG pipeline is build by Bechtel

    SciTech Connect (OSTI)

    Horner, C.

    1984-08-01

    The construction of the 313 mile long, 24 in. LPG pipeline from Hassi R'Mel to Arzew, Algeria is described. The pipeline was designed to deliver 6 million tons of LPG annually using one pumping station. Eventually an additional pumping station will be added to raise the system capacity to 9 million tons annually.

  10. Overview of the design, construction, and operation of interstate liquid petroleum pipelines.

    SciTech Connect (OSTI)

    Pharris, T. C.; Kolpa, R. L.

    2008-01-31

    The U.S. liquid petroleum pipeline industry is large, diverse, and vital to the nation's economy. Comprised of approximately 200,000 miles of pipe in all fifty states, liquid petroleum pipelines carried more than 40 million barrels per day, or 4 trillion barrel-miles, of crude oil and refined products during 2001. That represents about 17% of all freight transported in the United States, yet the cost of doing so amounted to only 2% of the nation's freight bill. Approximately 66% of domestic petroleum transport (by ton-mile) occurs by pipeline, with marine movements accounting for 28% and rail and truck transport making up the balance. In 2004, the movement of crude petroleum by domestic federally regulated pipelines amounted to 599.6 billion tonmiles, while that of petroleum products amounted to 315.9 billion ton-miles (AOPL 2006). As an illustration of the low cost of pipeline transportation, the cost to move a barrel of gasoline from Houston, Texas, to New York Harbor is only 3 cents per gallon, which is a small fraction of the cost of gasoline to consumers. Pipelines may be small or large, up to 48 inches in diameter. Nearly all of the mainline pipe is buried, but other pipeline components such as pump stations are above ground. Some lines are as short as a mile, while others may extend 1,000 miles or more. Some are very simple, connecting a single source to a single destination, while others are very complex, having many sources, destinations, and interconnections. Many pipelines cross one or more state boundaries (interstate), while some are located within a single state (intrastate), and still others operate on the Outer Continental Shelf and may or may not extend into one or more states. U.S. pipelines are located in coastal plains, deserts, Arctic tundra, mountains, and more than a mile beneath the water's surface of the Gulf of Mexico (Rabinow 2004; AOPL 2006). The network of crude oil pipelines in the United States is extensive. There are approximately 55

  11. Periodic review enhances LPG metering performance

    SciTech Connect (OSTI)

    Van Orsdol, F.G.

    1988-01-25

    Because of the loss of experienced personnel throughout the industry, the author says one must start over teaching the basics of liquid measurement. Warren Petroleum Co., a division of Chevron U.S.A. Inc., has developed a checklist review method for its metering systems, complete with enough explanation to allow the reviewer to understand why each item is important. Simultaneously, it continues with more in-depth and theoretical training in training course. This article describes the review process.

  12. Africa gaining importance in world LPG trade

    SciTech Connect (OSTI)

    Haun, R.R.; Otto, K.W.; Whitley, S.C.

    1997-05-12

    Major LPG projects planned or under way in Africa will increase the importance of that region`s presence in world LPG trade. Supplies will nearly double between 1995 and 2005, at which time they will remain steady for at least 10 years. At the same time that exports are leveling, however, increasing domestic demand for PG is likely to reduce export-market participation by Algeria, Nigeria, Egypt, and Libya. The growth of Africa`s participation in world LPG supply is reflected in comparisons for the next 15--20 years. Total world supply of LPG in 1995 was about 165 million metric tons (tonnes), of which Africans share was 7.8 million tonnes. By 2000, world supply will grow to slightly more than 200 million tonnes, with Africa`s share expected to increase to 13.2 million tonnes (6.6%). And by 2005, world LPG supply will reach nearly 230 million tonnes; Africa`s overall supply volumes by that year will be nearly 16.2 million tonnes (7%). World LPG supply for export in 1995 was on order of 44 million tonnes with Africa supply about 4 million tonnes (9%). By 2005, world export volumes of LPG will reach nearly 70 million tonnes; Africa`s share will have grown by nearly 10 million tonnes (14.3%).

  13. Fuel switching from wood to LPG can benefit the environment

    SciTech Connect (OSTI)

    Nautiyal, Sunil Kaechele, Harald

    2008-11-15

    The Himalaya in India is one of the world's biodiversity hotspots. Various scientific studies have reported and proven that many factors are responsible for the tremendous decline of the Himalayan forests. Extraction of wood biomass from the forests for fuel is one of the factors, as rural households rely entirely on this for their domestic energy. Efforts continue for both conservation and development of the Himalayan forests and landscape. It has been reported that people are still looking for more viable solutions that could help them to improve their lifestyle as well as facilitate ecosystem conservation and preservation of existing biodiversity. In this direction, we have documented the potential of the introduction of liquefied petroleum gas (LPG), which is one of the solutions that have been offered to the local people as a substitute for woodfuel to help meet their domestic energy demand. The results of the current study found dramatic change in per capita woodfuel consumption in the last two decades in the villages where people are using LPG. The outcome showed that woodfuel consumption had been about 475 kg per capita per year in the region, but after introduction of LPG, this was reduced to 285 kg per capita per year in 1990-1995, and was further reduced to 46 kg per capita per year in 2000-2005. Besides improving the living conditions of the local people, this transformation has had great environmental consequences. Empirical evidence shows that this new paradigm shift is having positive external effects on the surrounding forests. Consequently, we have observed a high density of tree saplings and seedlings in adjacent forests, which serves as an assessment indicator of forest health. With the help of the current study, we propose that when thinking about a top-down approach to conservation, better solutions, which are often ignored, should be offered to local people.

  14. Overfilling of cavern blamed for LPG blasts

    SciTech Connect (OSTI)

    Not Available

    1992-07-06

    Three explosions and a fire Apr. 7 at an LPG salt dome storage cavern near Brenham, Tex., were triggered when the cavern was overfilled, the Texas Railroad Commission (TRC) has reported. This paper reports that a TRC investigation found that LPG escaped to the surface at the Brenham site through brine injection tubing after excessive fill from an LPG line forced the cavern's water level below the brine tubing's bottom. At the surface, LPG was released into a brine storage pit where it turned into a dense, explosive vapor. At 7:08 a.m., the vapor was ignited by an unknown source. The resulting blast killed three persons and injured 19 and brought operations at the site to a halt.

  15. Alternative fuel information: Facts about CNG and LPG conversion

    SciTech Connect (OSTI)

    O`Connor, K.

    1994-06-01

    As new environmental and energy related laws begin to take effect, increasing numbers of alternative fuel vehicles (AFVs) will be required in federal, state, municipal, and private fleets across the country. The National Energy Policy Act of 1992 and the Clean Air Act Amendments of 1990, along with several new state and local laws, will require fleet managers to either purchase original equipment manufacturer (OEM) vehicles, which are produced by automakers, or convert existing vehicles to run on alternative fuels. Because there is a limited availability and selection of OEM vehicles, conversions are seen as a transition to the time when automakers will produce more AFVs for public sale. A converted vehicle is any vehicle that originally was designed to operate on gasoline, and has been altered to run on an alternative fuel such as compressed natural gas (CNG) or propane (liquefied petroleum gas -- LPG), the two most common types of fuel conversions. In the United States, more than 25,000 vehicles already have been converted to COG, and 300,000 have been converted to LPG.

  16. Urban leakage of liquefied petroleum gas and its impact on Mexico City air quality

    SciTech Connect (OSTI)

    Blake, D.R.; Rowland, F.S.

    1995-08-18

    Alkane hydrocarbons (propane, isobutane, and n-butane) from liquefied petroleum gas (LPG) are present in major quantities throughout Mexico City air because of leakage of the unburned gas from numerous urban sources. These hydrocarbons, together with olefinic minor LPG components, furnish substantial amounts of hydroxyl radical reactivity, a major precursor to formation of the ozone component of urban smog. The combined processes of unburned leakage and incomplete combustion of LPG play significant role in causing the excessive ozone characteristic of Mexico City. Reductions in ozone levels should be possible through changes in LPG composition and lowered rates of leakage. 23 refs., 3 tabs.

  17. Design and construction of liquefied petroleum gas installations (LPG)

    SciTech Connect (OSTI)

    Not Available

    1989-01-01

    This standard applies principally to both refrigerated and non-refrigerated installations that are larger in size than or closely associated with operating units, or both. The more complex problems presented by such installations require wider latitude for the designer than installations that are covered by the present National Fire Protection Association standards.

  18. LPG odorization with an audit trail

    SciTech Connect (OSTI)

    Astala, A.A.

    1995-12-01

    In this article I have tried to cover a very broad subject in a very limited time while only touching on a few of the ways you could odorize LPG and have an audit trail. I would recommend that if you are interested in this type of odorizing for LPG, you contact your odorant manufacturer and two or three odorant equipment manufacturers and talk to them about what you would like and get their recommendations. By talking to more then one manufacturer you may want to incorporate the ideals of two or three manufacturers into your odorant system to have a system that meets all your needs and requirements.

  19. New method developed for LPG offshore loading

    SciTech Connect (OSTI)

    Not Available

    1985-10-01

    An innovative concept for refrigerated LPG offshore loading has been developed by TOTAL and Enterprise D'Equipments Mecaniques at Hydrauliques. Known as CHAGAL, the system integrates with the catenary anchor leg mooring offshore loading system commonly used for crude oil. CHAGAL provides a suitable answer to short-term development schemes of LPG trade. It can be adapted for possible extrapolation to cryogenic temperatures of LNG and it opens a new way to the development of offshore liquefaction projects for which the offloading of production is still an unsolved key problem.

  20. Next generation processes for NGL/LPG recovery

    SciTech Connect (OSTI)

    Pitman, R.N.; Hudson, H.M.; Wilkinson, J.D.; Cuellar, K.T.

    1998-12-31

    Up to now, Ortloff`s Gas Subcooled Process (GSP) and OverHead Recycle Process (OHR) have been the state-of-the-art for efficient NGL/LPG recovery from natural gas, particularly for those gases containing significant concentrations of carbon dioxide (CO{sub 2}). Ortloff has recently developed new NGL recovery processes that advance the start-of-the-art by offering higher recovery levels, improved efficiency, and even better CO{sub 2} tolerance. The simplicity of the new process designs and the significantly lower gas compression requirements of the new processes reduce the investment and operating costs for gas processing plants. For gas streams containing significant amounts of carbon dioxide, the CO{sub 2} removal equipment upstream of the NGL recovery plant can be smaller or eliminated entirely, reducing both the investment cost and the operating cost for gas processing companies. In addition, the new liquids extraction processes can be designed to efficiently recover or reject ethane, allowing the gas processor to respond quickly to changing market conditions. This next generation of NGL/LPG recovery processes is now being applied to natural gas processing here in the US and abroad. Two of the new plants currently under construction provide practical examples of the benefits of the new processes.

  1. Product transfer service chosen over LPG flaring

    SciTech Connect (OSTI)

    Horn, J.; Powers, M.

    1994-07-01

    Seadrift Pipeline Corp. recently decommissioned its Ella Pipeline, an 108-mile, 8-in. line between the King Ranch and a Union Carbide plant at Seadrift, Texas. The pipeline company opted for the product transfer services of pipeline Dehydrators Inc. to evacuate the ethane-rich LPG mixture from the pipeline instead of flaring the LPG or displacing it with nitrogen at operating pressures into another pipeline. The product transfer system of Pipeline Dehydrators incorporates the use of highly specialized portable compressors, heat exchangers and interconnected piping. The product transfer process of evacuating a pipeline is an economically viable method that safely recovers a very high percentage of the product while maintaining product purity. Using positive-displacement compressors, PLD transferred the LPG from the idled 8-in. Ella line into an adjacent 12-in. ethane pipeline that remained in service at approximately 800 psig. Approximately 4.3 million lb of LPG (97% ethane, 2.7% methane and 0.3% propane) were transferred into the ethane pipeline, lowering the pressure on the Ella Pipeline from 800 psig to 65 psig.

  2. Vaporization, dispersion, and radiant fluxes from LPG spills. Final report

    SciTech Connect (OSTI)

    Not Available

    1981-12-01

    Both burning and non-burning spills of LPG (primarily propane) were studied. Vaporization rates for propane spills on soil, concrete, insulating concrete, asphalt, sod, wood, and polymer foams were measured. Thermal conductivity, heat transfer coefficients, and steady state vaporization rates were determined. Vapor concentrations were measured downwind of open propane pools 25, 100, 400, and 1600 ft/sup 2/ in area. A Gaussian dispersion model modified for area sources provided a good correlation of measured concentrations. Emitted and incident radiant fluxes from propane fires were measured. Simplified flame radiation models were adequate for predicting radiant fluxes; the maximum effective flux emitted at the flame surface was about 50,000 Btu/h-ft/sup 2/. A few tests in which propane was sprayed into the air showed that at moderately high spray rates all the propane flashed to vapor or atomized; no liquid collected on the ground.

  3. Novel coiled tubing application controls large LPG storage well fire

    SciTech Connect (OSTI)

    Gebhardt, F.; Eby, D.; Barnett, D.

    1996-06-01

    Conventional well control techniques for normal oil and gas wells are widely known and have been presented on numerous occasions. However, LPG storage (or cavern) wells rarely blow out and/or catch on fire. As a result, little information has been presented on the topic of well control for these types of wells. This article chronicles a case history of a high-volume liquid propane storage well fire. Because conventional wellhead removal methods could not be applied in this case, the capping/kill plan called for use of coiled tubing in a novel manner to cut the tubing downhole and install an inflatable packer to shut off propane flow. The plan was successfully executed, saving the operator millions of dollars in LPC product loss and cost of control.

  4. Study concerning the utilization of the ocean spreading center environment for the conversion of biomass to a liquid fuel. (Includes Appendix A: hydrothermal petroleum genesis). [Supercritical water

    SciTech Connect (OSTI)

    Steverson, M.; Stormberg, G.

    1985-01-01

    This document contains a report on the feasibility of utilizing energy obtained from ocean spreading centers as process heat for the conversion of municipal solid wastes to liquid fuels. The appendix contains a paper describing hydrothermal petroleum genesis. Both have been indexed separately for inclusion in the Energy Data Base. (DMC)

  5. Risk analysis of an LPG facility

    SciTech Connect (OSTI)

    Daley, H.F.; Chapman, P.D.L.

    1986-01-01

    This paper describes methods used to conduct a safety review of an existing LPG loading, processing, and storage facility. An engineering team conducted a Hazard and Operability study of the plant to identify potential problems. A Probabilistic Risk Assessment was also made on the facility where the probability and consequences of worst case accidents were estimated. Stone and Webster recently completed an analysis of an LPG terminal to determine if there were any engineering, design, or operating deficiencies which could jeopardize the operability of the facility or make operation hazardous. The facility includes a dock for off-loading refrigerated propane and butane, transfer piping from the dock to storage, a heating system, pressurized storage, dehydration, product transfer and loading.

  6. The operation of LPG relief valves

    SciTech Connect (OSTI)

    Stannard, J.H. Jr

    1989-11-01

    As stipulated by NFPA 58, all LPG storage containers must be equipped with one or more pressure relief devices. These devices are sized to prevent rupture of a normally charged container when exposed to fire. This paper describes in detail the functioning of the spring-loaded relief valve. The author discusses how the venting of LPGs can produce unacceptable risks and how training is a necessary part of controlling such a situation.

  7. U.S. LPG pipeline begins deliveries to Pemex terminal

    SciTech Connect (OSTI)

    Bodenhamer, K.C.

    1997-08-11

    LPG deliveries began this spring to the new Mendez LPG receiving terminal near Juarez, State of Chihuahua, Mexico. Supplying the terminal is the 265-mile, 8-in. Rio Grande Pipeline that includes a reconditioned 217-mile, 8-in. former refined-products pipeline from near Odessa, Texas, and a new 48-mile, 8-in. line beginning in Hudspeth County and crossing the US-Mexico border near San Elizario, Texas. Capacity of the pipeline is 24,000 b/d. The LPG supplied to Mexico is a blend of approximately 85% propane and 15% butane. Before construction and operation of the pipeline, PGPB blended the propane-butane mix at a truck dock during loading. Demand for LPG in northern Mexico is strong. Less than 5% of the homes in Juarez have natural gas, making LPG the predominant energy source for cooking and heating in a city of more than 1 million. LPG also is widely used as a motor fuel.

  8. Compressed natural gas and liquefied petroleum gas as alternative fuels

    SciTech Connect (OSTI)

    Moussavi, M.; Al-Turk, M. . Civil Engineering Dept.)

    1993-12-01

    The use of alternative fuels in the transportation industry has gained a strong support in recent years. In this paper an attempt was made to evaluate the use of liquefied petroleum gas (LPG) and compressed natural gas (NG) by 25 LPG-bifuel and 14 NG-bifuel vehicles that are operated by 33 transit systems throughout Nebraska. A set of performance measures such as average fuel efficiency in kilometers per liter, average fuel cost per kilometer, average oil consumption, and average operation and maintenance cost for alternatively fueled vehicles were calculated and compared with similar performance measures of gasoline powered vehicles. The results of the study showed that the average fuel efficiency of gasoline is greater than those of LPG and NG, and the average fuel costs (dollars per kilometer) for LPG and NG are smaller than those for gasoline for most of the vehicles under this study.

  9. Radiological health implications of lead-210 and polonium-210 accumulations in LPG refineries

    SciTech Connect (OSTI)

    Summerlin, J. Jr.; Prichard, H.M.

    1985-04-01

    Radon-222, a naturally occurring radioactive noble gas, is often a contaminant in natural gas. During fractionation at processing plants, Radon tends to be concentrated in the Liquified Petroleum Gas (LPG) product stream. Radon-222 decays into a number of radioactive metallic daughters which can plate out on the interior surfaces of plant machinery. The hazards associated with gamma-emitting short-lived radon daughters have been investigated previously. The present work reports an analysis of the hazards associated with the long-lived daughters; Pb-210, Bi-210, and Po-210. These nuclides do not emit appreciable penetrating radiation, and hence do not represent a hazard as long as they remain on the inside surfaces of equipment. However, when equipment that has had prolonged exposure to an LPG stream is disassembled for repair or routine maintenance, opportunities for exposure to radioactive materials can occur. A series of measurements made on an impeller taken from a pump in an LPG facility is reported. Alpha spectroscopy revealed the presence of Po-210, and further measurements showed that the amount on the impeller surface was well above the exempt quantity. Breathing zone measurements made in the course of cleaning the impeller showed that an inhalation exposure equivalent to breathing Po-210 at the Maximum Permissible Concentration (MPC) for 60 hours could be delivered in less than half an hour. It was concluded that maintenance and repair work on LPG and derivitive product stream equipment must be carried out with the realization that a potential radiological health problem exists.

  10. A technical and economic assessment of petroleum, heavy oil, shale oil and coal liquid refining

    SciTech Connect (OSTI)

    Sikonia, J.G.; Shah, B.R.; Ulowetz, M.A.

    1983-11-01

    Decreasing availability of conventional crude oil will result in the utilization of alternative raw materials for the production of transportation fuels. Based on currently available processes and as a result of detailed pilot plant studies, the differences in the technical and economic aspects of refining alternative feedstocks of heavy oil, coal liquids and shale oil have indicated that heavy, hydrogen-deficient materials require more complex and costly upgrading techniques. Compared to the base case of Arabian Light crude oil, the Mexican Maya heavy oil is worth about $4.35/B less, the coal liquid about $2.38/B less and the shale oil about $5.98/B less. All of these alternative fuels can be upgraded into high quality transportation fuels.

  11. Synergistic routes to liquid fuel for a petroleum-deprived future

    SciTech Connect (OSTI)

    Agrawal, R.; Singh, N.R.

    2009-07-15

    When compared with biomass gasification/Fischer-Tropsch synthesis, hydropyrolysis/hydrodeoxygenation (HDO)-based processes have a potential to achieve high biomass carbon conversion to liquid fuel with much lower amounts of supplementary H{sub 2}. On the basis of this observation, we suggest a Hydrogen Bio-oil (H{sub 2}Bioil) process using fast hydropyrolysis/HDO that has a potential to produce nearly double the amount of liquid fuel when compared with the existing biofuel processes while requiring only modest quantities of supplementary H{sub 2}. The optimal operating mode for the H{sub 2}Bioil process is suggested to be in an entrained bed mode in presence of H{sub 2} with gas phase HDO of hydropyrolyzed vapors. A remarkable result due to reduced need for the supplementary H{sub 2} is that it provides synergistic integration of the H(2)Bioil process with a coal gasification power plant or a small scale steam natural gas (NG) reformer leading to a dramatic increase in the liquid fuel production from biomass and coal or NG. Here, hot synthesis gas (T>500{sup o}C) from a coal gasifier or methane reformer supplies H{sub 2}/CO for hydropyrolysis and deoxygenation as well as heat for the process. This result is exciting, because it presents us with an option to build integrated H{sub 2}Bioil processes sooner rather than later when the cost effective H{sub 2}, becomes available from a carbon-free energy source such as solar or nuclear. The H{sub 2}Bioil process and its integrated version with a small scale NG reformer have strong potential to be attractive on a small scale while being more efficient than any current biomass to liquid fuel process in operation.

  12. Source rock geochemistry and liquid and solid petroleum occurrences of the Ouachita Mountains, Oklahoma

    SciTech Connect (OSTI)

    Curiale, J.A.

    1981-01-01

    Crude oils, solid bitumens and potential oil source rocks of the Frontal and Central Ouachita Mountains of southeastern Oklahoma were examined. The purposes of this study are to characterize the organic matter in each of these materials, and to correlate oils to potential source rocks in the Ouachita Mountains. Four Ouachita Mountain oils and seven solid bitumens (grahamite and impsonite were analyzed. The oils are paraffinic and range from 31.8 to 43.1 API gravity. Results indicate that the oils are thermally mature and generally unaltered. All four oils are commonly sourced, as suggested by n-alkane, sterane and hopane distributions, stable isotope ratios, infrared spectra and vanadium/nickel ratios. A common source for the solid bitumens is also suggested by isotope ratios and pyrolyzate characteristics. An origin due to crude oil biodegradation is suggested for these solids, based on carbon isotope ratios, elemental analyses, and sterane distributions of the solid bitumen pyrolyzates. Several stratigraphic intervals in the Ouachita Mountains possess adequate source potential for petroleum generation, based on contents of total organic carbon and extractable organic matter. Devonian rocks are oil-generative. The entire Paleozoic section examined is thermally mature enough to have generated oil, being located at about the middle of the oil window. In general, the best oil source potential is present in upper Ordovician (Polk Creek/Womble) rocks. Oil-source rock correlation techniques indicate that oils examined from the Frontal and Central Ouachita Mountains have a Siluro-Ordovician (Missouri Mountain-Polk Creek-Womble) source.

  13. Current and future USA-world seaborne imports at LPG

    SciTech Connect (OSTI)

    Bassa, G.

    1980-01-01

    An outline of the current and historical situation of the international LPG trade and comparison between the US and other countries covers methods of marine transportation, including fully refrigerated vessels, semirefrigerated vessels, pressure vessels, and LNG ships fitted for LPG; the temporary abundance of LPG; a comparison of the markets in Japan, Europe, South America, and the US to indicate the potential market in the future, e.g., the need in Japan for LPG as a basic fuel, main use in Europe as a feedstock and as domestic fuel, use as a basic fuel but mainly in the winter months inSouth America, and the volatile spot market in the US; and the conclusion that the capacity to produce LPG will keep pace with demand only as long as adequate prices are paid to offset production costs.

  14. Charcoal versus LPG grilling: A carbon-footprint comparison

    SciTech Connect (OSTI)

    Johnson, Eric

    2009-11-15

    Undoubtedly, grilling is popular. Britons fire up their barbeques some 60 million times a year, consuming many thousands of tonnes of fuel. In milder climates consumption is even higher, and in the developing world, charcoal continues to be an essential cooking fuel. So it is worth comparing the carbon footprints of the two major grill types, charcoal and LPG, and that was the purpose of the study this paper documents. Charcoal and LPG grill systems were defined, and their carbon footprints were calculated for a base case and for some plausible variations to that base case. In the base case, the charcoal grilling footprint of 998 kg CO{sub 2}e is almost three times as large as that for LPG grilling, 349 kg CO{sub 2}e. The relationship is robust under all plausible sensitivities. The overwhelming factors are that as a fuel, LPG is dramatically more efficient than charcoal in its production and considerably more efficient in cooking. Secondary factors are: use of firelighters, which LPG does not need; LPG's use of a heavier, more complicated grill; and LPG's use of cylinders that charcoal does not need.

  15. Cylinder surface, temperature may affect LPG odorization

    SciTech Connect (OSTI)

    McWilliams, H.

    1988-01-01

    A study of possible odorant fade in propane by the Arthur D. Little Co. (Boston) has indicated that oxidation of interior surfaces of LPG containers may cause the odorant, ethyl mercaptan, to fade. The oxidation, ferous oxide, is a black, easily oxidizable powder that is the monoxide of iron. The study, contracted for by the Consumer Product Safety Commission (CPSC), is part of that agency's study of residential LP-gas systems. Another study is currently underway by an NLPGA task force headed by Bob Reid of Petrolane (Long Beach, Calif.). It may not be finished until the end of next year. Recently, the Propane Gas Association of Canada completed a study of odorant fade with the conclusion that much more study is needed on the subject. In addition to the cylinder surface problem, the CPSC study indicated that ambient temperatures might also affect the presence of odorant in product. This article reviews some of the results.

  16. End to deficit of LPG. [Argentina

    SciTech Connect (OSTI)

    Andrich, V.

    1980-03-01

    In the Buenos Aires province of Argentina, Gas de Estado is constructing the future heart of the petrochemical complex, Bahia Blanca. The complex contains 2 absorption-refrigeration plants, a gas compressing plant, equipment maintenance shops and an important operations base for the Argentine truck gas pipelines. This will be the largest LPG plant in Latin America. The General Cerri plant, under construction, is located in an area of 40,000 sq m with new installations to extract ethane and higher hydrocarbons. The design optimizes the extraction of hydrocarbons from the natural gas and recovers 76% of the ethane. Selection of the process resulted from an investigation that compared the system with processes that use water cooling and absorption with refrigerated oil.

  17. LPG export growth will exceed demand by 2000

    SciTech Connect (OSTI)

    True, W.R.

    1994-08-08

    LPG supplies for international trade will increase sharply through 2000 and begin to outstrip demand by 1997 or 1998. This outlook depends on several production projects proceeding as planned. Leading the way to increased volumes are projects in Algeria, Nigeria, and Australia, among others. Purvin and Gertz, Dallas, projected this trend earlier this year at an international LPG seminar near Houston. Representatives from LPG-supplying countries also presented information to support this view and subsequently supplied more specifics to OGJ in response to questions. This paper discusses this information. Trends in Africa, Australia, North America, and South America are forecast.

  18. FCC LPG olefinicity and branching enhanced by octane catalysts

    SciTech Connect (OSTI)

    Keyworth, D.A.; Reid, T.A.; Kreider, K.R.; Yatsu, C.A.

    1989-05-29

    Refiners are increasingly recognizing the downstream opportunities for fluid catalytic cracking LPG olefins for the production of methyl tertiary butyl ether (MTBE), ethyl tertiary butyl ether (ETBE, if the ethanol subsidy is extended to the production of ETBE), and as petrochemical feedstocks. Some of new gasoline FCC octane-enhancing catalysts can support those opportunities because their low non-framework alumina (low NFA) preserve both LPG olefinicity and promote branching of the LPG streams from the FCCU. The combined effect results in more isobutane for alkylate feed, more propylene in the propane/propylene stream, and more isobutene - which makes the addition of an MTBE unit very enticing.

  19. Monitoring, safety systems for LNG and LPG operators

    SciTech Connect (OSTI)

    True, W.R.

    1998-11-16

    Operators in Korea and Australia have chosen monitoring and control systems in recent contracts for LNG and LPG storage. Korea Gas Corp. (Kogas) has hired Whessoe Varec, Calais, to provide monitoring systems for four LNG storage tanks being built at Kogas` Inchon terminal. For Elgas Ltd., Port Botany, Australia, Whessoe Varec has already shipped a safety valve-shutdown system to a new LPG cavern-storage facility under construction. The paper describes the systems, terminal monitoring, dynamic approach to tank management, and meeting the growing demand for LPG.

  20. LPG-recovery processes for baseload LNG plants examined

    SciTech Connect (OSTI)

    Chiu, C.H.

    1997-11-24

    With demand on the rise, LPG produced from a baseload LNG plant becomes more attractive as a revenue-earning product similar to LNG. Efficient use of gas expanders in baseload LNG plants for LPG production therefore becomes more important. Several process variations for LPG recovery in baseload LNG plants are reviewed here. Exergy analysis (based on the Second Law of Thermodynamics) is applied to three cases to compare energy efficiency resulting from integration with the main liquefaction process. The paper discusses extraction in a baseload plant, extraction requirements, process recovery parameters, extraction process variations, and exergy analysis.

  1. Synthesis gas conversion to LPG over molybdenum catalysts

    SciTech Connect (OSTI)

    Murchison, C.B.; Murdick, D.A.

    1980-01-01

    By using a new Dow Chemical Co. carbon-supported molybdenum oxide catalyst promoted with 4.4% K/sub 2/O or Na/sub 2/O, 90%+ conversions of synthesis gas at space velocities of 500-600/hr were achieved with 60-75% selectivities for C/sub 2/-C/sub 5/ paraffins, including 33 and 27% for ethane and propane, respectively, and no liquid products formed. This LPG product is an excellent ethylene cracking feedstock. The catalyst, which can be used in both oxide and sulfided forms, has demonstrated stable performance with feeds containing up to 20 ppm sulfur (H/sub 2/S + COS) and had no coking problems for up to 2000 hr on stream. Excessive sulfur exposure can be reversed by regeneration with hydrogen. Because of the catalyst's low coking rate, high temperatures, i.e., 350/sup 0/-500/sup 0/C, and near-stoichiometric H/sub 2//CO feed ratios can be used.

  2. OXY (Occidental Petroleum Corp. ) units plan U. K. work worth $1. 5 billion

    SciTech Connect (OSTI)

    Not Available

    1980-09-15

    Occidental Refineries Ltd., an Occidental Petroleum Corp. subsidiary, plans to spend about $500,000 to build a 60,000 bbl/day hydrocracker on Canvey Island near London to produce aviation fuel, naphtha, and gasoline. Occidental hopes to deflect criticism by environmentalists, concerned about the concentration of petroleum facilities in the area, by installing a minimum amount of LPG storage and not using hydrogen sulfide on the site. During the 1970's, Occidental had prepared the site for the construction of a 125,000 bbl/day refinery, plans for which were scrapped after the demand for product compounds decreased. Occidental Chemical Co., another Occidental Petroleum subsidiary, plans to spend about $500,000 to build a 300,000 ton/yr ethylene plant at Peterhead, Scotl. The cracker would take part of the output from the de-ethanizer at the St. Fergus terminal for the proposed U.K. gas-gathering pipeline. Both projects would require about 3-4 yr to complete. Esso Chemical Ltd. will build a 550,000 ton/yr ethylene plant near the Mossmoran gas liquids plant in Fife, Scotl.

  3. Cost-effectiveness analysis of TxDOT LPG fleet conversion. Volume 1. Interim research report

    SciTech Connect (OSTI)

    Euritt, M.A.; Taylor, D.B.; Mahmassani, H.

    1992-10-01

    Increased emphasis on energy efficiency and air quality has resulted in a number of state and federal initiatives examining the use of alternative fuels for motor vehicles. Texas' program for alternate fuels includes liquefied petroleum gas (LPG). Based on an analysis of 30-year life-cycle costs, development of a propane vehicle program for the Texas Department of Transportation (TxDOT) would cost about $24.3 million (in 1991 dollars). These costs include savings from lower-priced LPG and differentials between propane and gasoline/diesel in infrastructure costs for a fueling station, vehicle costs, and operating costs. The 30-year life-cycle costs translate into an average annual vehicle cost increase of $308, or about 2.5 cents more per vehicle mile of travel. Sensitivity analyses are performed on the discount rate, price of propane, maintenance savings, vehicle utilization, diesel vehicles, extended vehicle life, original equipment manufacturer (OEM) vehicles, and operating and infrastructure costs. The best results are obtained when not converting diesel vehicles, converting only large fleets, and extending the period the vehicle is kept in service. Combining these factors yields results that are most cost-effective for TxDOT. This is volume one of two volumes.

  4. Evaluation of aftermarket fuel delivery systems for natural gas and LPG vehicles

    SciTech Connect (OSTI)

    Willson, B. )

    1992-09-01

    This study was designed to evaluate the effectiveness of aftermarket fuel delivery systems for vehicles fueled by compressed natural gas (CNG) and liquefied petroleum gas (LPG). Most of the CNG and LPG vehicles studied were converted to the alternative fuel after purchase. There are wide variations in the quality of the conversion hardware and the installation. This leads to questions about the overall quality of the converted vehicles, in terms of emissions, safety, and performance. There is a considerable body of emissions data for converted light-duty vehicles, and a smaller amount for medium- and heavy-duty vehicles. However, very few of these data involve real world conditions, and there is growing concern about in-use emissions. This report also attempts to assess factors that could allow in-use emissions to vary from the best-case'' results normally reported. The study also addresses issues of fuel supply, fuel composition, performance, safety, and warranty waivers. The report is based on an extensive literature and product survey and on the author's experience with fuel delivery systems for light-duty vehicles.

  5. Evaluation of aftermarket fuel delivery systems for natural gas and LPG vehicles

    SciTech Connect (OSTI)

    Willson, B.

    1992-09-01

    This study was designed to evaluate the effectiveness of aftermarket fuel delivery systems for vehicles fueled by compressed natural gas (CNG) and liquefied petroleum gas (LPG). Most of the CNG and LPG vehicles studied were converted to the alternative fuel after purchase. There are wide variations in the quality of the conversion hardware and the installation. This leads to questions about the overall quality of the converted vehicles, in terms of emissions, safety, and performance. There is a considerable body of emissions data for converted light-duty vehicles, and a smaller amount for medium- and heavy-duty vehicles. However, very few of these data involve real world conditions, and there is growing concern about in-use emissions. This report also attempts to assess factors that could allow in-use emissions to vary from the ``best-case`` results normally reported. The study also addresses issues of fuel supply, fuel composition, performance, safety, and warranty waivers. The report is based on an extensive literature and product survey and on the author`s experience with fuel delivery systems for light-duty vehicles.

  6. River resort owners find LPG a power behind their success

    SciTech Connect (OSTI)

    Not Available

    1991-01-01

    This paper reports on a restaurant and resort which runs entirely on LPG. It has two generators converted to LPG that supply the power for the complex. Energy supplied from the propane is used in the kitchens, to drive the water pump and provide electricity for lighting and other power needs, and to heat the swimming pool. Far more importantly for the owners has been the fuel cost savings of at least 60%.

  7. World`s LPG supply picture will change by 2000

    SciTech Connect (OSTI)

    True, W.R.

    1995-11-06

    Middle East LPG producers will continue to dominate world export markets in 1996. Led by Saudi Arabia, the Middle East will produce nearly 26 million metric tons of LPG in million metric tons of LPG in 1996, more than 54% of the world`s almost 48 million metric tons of export LPG. In 2000, however, with world exports of LPG expanding to 58.9 million metric tons, Middle East suppliers; share will have remained flat, making up 31.7 million metric tons, or 53.9%. Saudi Arabia`s contribution will exceed 15 million metric tons, reflecting essentially no growth since 1995. These and other patterns, from data compiled by Purvin and Gertz, Dallas, and published earlier this year, show other suppliers of LPG, especially African (Algeria/Nigeria), North Sea, and Latin American (Venezuela/Argentina), picking up larger shares in the last 5 years of this decade. This scenario assumes completion of several major supply projects that are either panned, under construction, or nearing start up in most of these areas. The paper discusses the global picture, the supply situation in the Middle East, Africa, the North Sea, and South America.

  8. Petroleum & Other Liquids

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    16,392 16,668 16,960 18,485 17,800 17,063 1990-2016 Total Motor Gasoline 72,064 72,003 72,493 71,316 70,915 70,125 1990-2016 Finished Motor Gasoline 4,915 5,108 5,450 5,341 4,763 5,914 1994-2016 Reformulated 30 30 21 21 29 28 1993-2016 Blended with Fuel Ethanol 30 30 21 21 29 28 2004-2016 Conventional 4,885 5,078 5,429 5,320 4,734 5,886 1994-2016 Blended with Fuel Ethanol, Ed55 and Lower 52 52 52 52 58 58 2004-2016 Blended with Fuel Ethanol, Greater than Ed55 0 0 0 0 0 0 2010-2016 Other 4,833

  9. Changing Global Petroleum Product Trade Flows

    U.S. Energy Information Administration (EIA) Indexed Site

    U.S. demand for liquid fuels has been relatively flat, while the demand in the rest of the ... U.S. petroleum demand (left axis) rest of world petroleum demand (right axis) ...

  10. Rio Grande pipeline introduces LPG to Mexico

    SciTech Connect (OSTI)

    1997-06-01

    Rio Grande Pipeline, a joint venture between Mid-America Pipeline Co., Amoco Pipeline Co. and Navajo Pipeline Co., has broken new ground in the energy industry as the first LPG pipeline to cross the US-Mexico border. Plans for the project were announced in November 1995 and first deliveries started three months ago on March 21, 1997. The 8-inch, 265-mile pipeline originates near Odessa, TX, where it receives an 85-15 propane-butane mix via a connection to Mid-America Pipeline. From Odessa, product moves west through the Texas desert and crosses the Rio Grande River about 15 miles south of El Paso near Clint, TX and extends 20 miles into Mexico. Capacity of the line is 24,000 bpd and it has been averaging about 22,000 bpd since line-fill. All in all, it sounded like a reasonably feasible, routine project. But perceptions can be deceiving, or at least misleading. In other words, the project can be summarized as follows: one river, two cultures and a world of difference. The official border crossing for pipeline construction took place on Dec. 2, 1996, with a directional drill under the Rio Grande River, but in actuality, the joint venture partners were continually bridging differences in language, laws, customs and norms with Pemex and contracted workers from Mexico.

  11. Indonesia's Arun LPG plant production is unique in Far East markets

    SciTech Connect (OSTI)

    Naklie, M.M.; Penick, D.P.; Denton, L.A.; Kartiyoso, I.

    1987-08-03

    Entry of the Arun (Indonesia) LNG plant into the LPG Far East markets is significant because its supplies for those markets are not tied to gas being extracted in association with crude oil. Arun LPG products are extracted from gas that is processed into and marketed as LNG. This article on the Arun LNG plant analyzes its LPG process and the significance of the LPG project on the plant's markets. Particular attention is paid to: 1.) LPG recovery; 2.) LPG fractionation; and 3.) Far East trade.

  12. The importance of FCC catalyst selection on LPG profitability

    SciTech Connect (OSTI)

    Keyworth, D.A.; Gilman, R.; Pearce, J.R. )

    1989-01-01

    Recently the value of LPG in chemical operations downstream of the FCC unit has increased. Such downstream operations utilize propylene not only in alkylate, but also in rapid growth petrochemical applications such as for a raw material in the manufacture of polypropylene and propylene oxide. Isobutane and the butenes (particularly butene-2 in sulfuric acid catalyzed alkylation units) are prized for alkylate feed. The profit potential and incentives to use other LPG components such as isobutene to make MTBE is now increased because of legislative actions and increased octane performance demand; and because of the greater isobutene content in the LPG from the new FCC octane catalysts. A low non-framework alumina (NFA) zeolite studied made a more olefinic LPG with higher iso-to normal C4 ratio than the other zeolites. Pilot plant data has also shown the new low NFA zeolite gave not only outstanding motor octane (MON) performance, but produced an LPG with better propylene to propane ratio, more isobutene, more n-butenes and more C4 branching than other RE promoted zeolite catalysts. Commercial results have verified the improved performance and profitability for the new low-NFA type zeolite catalysts. Three commercial examples are described.

  13. Petroleum Supply Annual, Volume 1

    U.S. Energy Information Administration (EIA) Indexed Site

    Petroleum & Other Liquids Reports Petroleum Supply Annual, Volume 1 With Data for 2014 | Release Date: September 25, 2015 | Next Release Date: September 2016 Previous Issues Year: 2014 2013 2012 2011 2010 2009 2008 2007 2006 2005 2004 2003 2002 2001 2000 1999 1998 1997 1996 1995 Go Volume 1 - Final annual data for the supply and disposition of crude oil and petroleum products. Volume 1 Tables All Tables All Tables Detailed Statistics Tables National Statistics 1 U.S. Supply, Disposition, and

  14. Cascaded'' pilot regulators help reduce LPG loss in hot weather

    SciTech Connect (OSTI)

    Not Available

    1994-08-08

    Fina Oil and Chemical Co. and Fisher Controls International used engineering resourcefulness to overcome heat-induced product loss from LPG storage bullets at Fina's Port Arthur, Tex., refinery. Fina had installed Fisher's Easy Joe 399A-6365, a pilot-operated, back-pressure-type regulator, on its LPG storage facility in 1991 as part of a fuel products modernization project. The regulators helped control the accumulation of noncondensible vapors, which collect in the storage bullets above the LPG. But summer heat extremes and surges in the tanks and lines made it possible for the operating pressure to increase so that the safety relief valve was activated before the pilot regulator was able to stabilize the pressure. The installation of pilot-type regulators, in cascaded, or series, formation, reduced product venting through relief valves.

  15. Low temperature type new TMCP steel plate for LPG carriers

    SciTech Connect (OSTI)

    Suzuki, Shuichi; Bessyo, Kiyoshi; Arimochi, Kazushige; Yajima, Hiroshi; Tada, Masuo; Sakai, Daisuke

    1994-12-31

    New Thermo-Mechanical Control Process (TMCP) steel plate for LPG carriers of completely liquefied type was developed with non-nickel chemistry. The new steel plate has a capability to arrest a long running brittle crack at {minus}46 C (which is the design temperature of the liquefied LPG tanks). A high heat-input one-pass welding can be applied to this steel despite its nickel-less chemistry. These capabilities were enabled by microalloying technology with low aluminum-medium nitrogen-boron, as well as by the advanced Thermo-Mechanical Control Process. This paper describes the new concept of utilizing the trace elements and the evaluation test results as the steel plate for the LPG tank and hull, especially from the standpoints of the fracture safe reliability at high heat input welding and from that of the shop workability.

  16. Assessment of research and development (R and D) needs in LPG safety and environmental control

    SciTech Connect (OSTI)

    DeSteese, J.G.

    1982-05-01

    The report characterizes the LPG industry covering all operations from production to end use, reviews current knowledge of LPG release phenomenology, summarizes the status of current LPG release prevention and control methodology, and identifies any remaining safety and environmental problems and recommends R and D strategies that may mitigate these problems. (ACR)

  17. Petroleum products

    SciTech Connect (OSTI)

    Not Available

    1987-01-01

    This book is the first of three volumes devoted to petroleum products and lubricants. This volume begins with standard D 56 and contains all petroleum standards up to D 1947. It contains specifications and test methods for fuels, solvents, burner fuel oils, lubricating oils, cutting oils, lubricating greases, fluids measurement and sampling, liquified petroleum gases, light hydrocarbons, plant spray oils, sulfonates, crude petroleum, petrolatam, and wax.

  18. Design considerations for sweetening LPG`s with amines

    SciTech Connect (OSTI)

    Bullin, J.A.; Polasek, J.; Rogers, J.

    1995-11-01

    In recent years, there has been increasing interest in sweetening LPG with amines. However, limited data and design information are available in the literature. In the present paper, the design considerations and alternatives including static mixers, jet educator mixers and columns with structured packing, random packing and sieve trays are compared based on plant operating data.

  19. Expansion fractionation capacity of the LPG-ULE plant

    SciTech Connect (OSTI)

    Morin, L.M.C.

    1999-07-01

    The Western Division of PDVSA has among other facilities a NGL Fractionation Complex located onshore in Ul'e. The complex consists of three plants, the first and second older plants, LPG-1 and LPG-2, which fractionate the NGL to produce propane, a butane mix and natural gasoline. The third plant, LPG-3, fractionates the butane mix from the LPG-1 and 2 plants to produce iso and normal butane. Several optimization projects already in progress will increase the NGL production to 12,200 b/d. For this reason it was decided to conduct a study of the existing fractionation facilities and utilities systems to determine their capacities. This evaluation revealed that some of the fractionation towers would have some limitations in the processing of the expected additional production. The study recommended an option to increase the capacity of the fractionation towers by lowering their operating pressure, in order to take advantage of relative volatility increase between the key components, which allows easier separation, as well as reducing the heat duty required. The completed study also determined that this option is more economically convenient than the replacement of the existing fractionation towers.

  20. Control and extinguishment of LPG fires. Final report

    SciTech Connect (OSTI)

    Not Available

    1980-06-01

    Approximately 100 fire control and fire extinguishment tests were run on free-burning LPG pool fires from 25 ft/sup 2/ to 1600 ft/sup 2/ in area. The LPG was contained in concrete pits, and the pit floors were allowed to cool before the fires were ignited so that the burning rates were not influenced by boiloff from the warm floor. High expansion foam was used for fire control. The foam was applied from fixed generators located on the upwind side of the pit. Fires were controlled after foam application of less than a minute to about 10 minutes, depending on the application rate. Fires were extinguished with dry chemical agents applied through fixed piping systems with tankside nozzles and by manual application using hoselines and portable extinguishers. Fires could readily be extinguished in times ranging from a few seconds to about half a minute, depending on the application rate, system design, and ambient conditions. Additional tests were conducted in 1-ft/sup 2/ and 5-ft/sup 2/ pits to determine the boiloff rates for LPG spilled on concrete, a sand/soil mix, and polyurethane foam substrates. Burning rates for free-burning LPG pool fires from 1 ft/sup 2/ to 1600 ft/sup 2/ in area are also reported.

  1. Petroleum Supply Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    0.PDF Table 20. Blender Net Inputs of Petroleum Products by PAD Districts, January 2014 (Thousand Barrels) Commodity PAD District 1 - East Coast PAD District 2 - Midwest East Coast Appalachian No. 1 Total Indiana, Illinois, Kentucky Minnesota, Wisconsin, North and South Dakota Oklahoma, Kansas, Missouri Total Natural Gas Plant Liquids and Liquefied Refinery Gases ....................................................... 358 2 360 69 38 259 366 Pentanes Plus

  2. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    1 June 2016 Table 32. Blender Net Inputs of Petroleum Products by PAD District, June 2016 (Thousand Barrels) Commodity PAD District 1 - East Coast PAD District 2 - Midwest East Coast Appalachian No. 1 Total Indiana, Illinois, Kentucky Minnesota, Wisconsin, North and South Dakota Oklahoma, Kansas, Missouri Total Natural Gas Plant Liquids and Liquefied Refinery Gases ....................................................... 21 - 21 - 10 85 95 Pentanes Plus

  3. Carbon footprints of heating oil and LPG heating systems

    SciTech Connect (OSTI)

    Johnson, Eric P.

    2012-07-15

    For European homes without access to the natural gas grid, the main fuels-of-choice for heating are heating oil and LPG. How do the carbon footprints of these compare? Existing literature does not clearly answer this, so the current study was undertaken to fill this gap. Footprints were estimated in seven countries that are representative of the EU and constitute two-thirds of the EU-27 population: Belgium, France, Germany, Ireland, Italy, Poland and the UK. Novelties of the assessment were: systems were defined using the EcoBoiler model; well-to-tank data were updated according to most-recent research; and combustion emission factors were used that were derived from a survey conducted for this study. The key finding is that new residential heating systems fuelled by LPG are 20% lower carbon and 15% lower overall-environmental-impact than those fuelled by heating oil. An unexpected finding was that an LPG system's environmental impact is about the same as that of a bio heating oil system fuelled by 100% rapeseed methyl ester, Europe's predominant biofuel. Moreover, a 20/80 blend (by energy content) with conventional heating oil, a bio-heating-oil system generates a footprint about 15% higher than an LPG system's. The final finding is that fuel switching can pay off in carbon terms. If a new LPG heating system replaces an ageing oil-fired one for the final five years of its service life, the carbon footprint of the system's final five years is reduced by more than 50%.

  4. Short-Term Outlook for Hydrocarbon Gas Liquids - Energy Information...

    U.S. Energy Information Administration (EIA) Indexed Site

    Highlights Prices Global Petroleum and Other Liquids U.S. Petroleum and Other Liquids Natural Gas Coal Electricity Renewables and Carbon Dioxide Emissions U.S. Economic Assumptions ...

  5. Cryogenic recovery of LPG from natural gas

    SciTech Connect (OSTI)

    Gray, M.L.; McClintock, W.A.

    1984-02-07

    In accordance with the present invention a natural gas stream predominating in methane and containing significant amounts of C/sub 2/, C/sub 3/, C/sub 4/ and C/sub 5/ and higher molecular weight hydrocarbons is cooled in a plurality of cooling stages to a temperature sufficient to produce at least one liquid phase portion predominating in C/sub 2/, C/sub 3/, C/sub 4/ and C/sub 5/ and higher molecular weight hydrocarbons. Then at least one liquid phase portion predominating in C/sub 2/, C/sub 3/, C/sub 4/ and C/sub 5/ and higher molecular weight hydrocarbons is separated from the main gas stream during the course of the cooling. The thus separated liquid phase portion or portions predominating in C/sub 2/, C/sub 3/, C/sub 4/ and C/sub 5/ and higher molecular weight hydrocarbons is further separated into a vapor phase portion predominating in C/sub 2/, C/sub 3/, and C/sub 4/ hydrocarbons and at least one liquid phase portion predominating in C/sub 5/ and higher molecular weight hydrocarbons, at least one second separation step, at least one portion of the at least one vapor phase portion predominating in C/sub 2/, C/sub 3/ and C/sub 4/, hydrocarbons is recovered as at least one product of the process and at least one portion of the remaining portion of the at least one phase portion predominating in C/sub 2/, C/sub 3/ and C/sub 4/ hydrocarbons is recycled to and recombined with the main gas stream as a liquid phase.

  6. Vaporization, dispersion, and radiant fluxes from LPG spills. Final technical report

    SciTech Connect (OSTI)

    Not Available

    1982-05-01

    Both burning and non-burning spills of LPG (primarily propane) were studied. Vaporization rates for propane spills on soil, concrete, insulating concrete, asphalt, sod, wood, and polymer foams were measured. Thermal conductivity, heat transfer coefficients, and steady state vaporization rates were determined. Vapor concentrations were measured downwind of open propane pools and a Gaussian dispersion model modified for area sources provided a good correlation of measured concentrations. Emitted and incident radiant fluxes from propane fires were measured. Simplified flame radiation models were adequate for predicting radiant fluxes. Tests in which propane was sprayed into the air showed that at moderately high spray rates all the propane flashed to vapor or atomized; no liquid collected on the ground.

  7. Atomic Force Microscopy Studies of Lipophosphoglycan (LPG) Molecules in Lipid Bilayers

    SciTech Connect (OSTI)

    LAST, JULIE A.; HUBER, TINA; SASAKI, DARRYL Y.; SALVATORE, BRIAN; TURCO, SALVATORE J.

    2003-03-01

    Lipophosphoglycan (LPG) is a lypopolysaccharide found on the surface of the parasite Leishmania donovani that is thought to play an essential role in the infection of humans with leishamniasis. LPG acts as an adhesion point for the parasite to the gut of the sand fly, whose bite is responsible for transmitting the disease. In addition, LPG acts to inhibit protein kinase C (PKC) in the human macrophage, possibly by structural changes in the membrane. The Ca{sup 2+} ion is believed to play a role in the infection cycle, acting both as a crosslinker between LPG molecules and by playing a part in modulating PKC activity. To gain insight into the structure of LPG within a supported lipid membrane and into the structural changes that occur due to Ca{sup 2+} ions, we have employed the atomic force microscope (AFM). We have observed that the LPG molecules inhibit bilayer fusion, resulting in bilayer islands on the mica surface. One experiment suggests that the LPG molecules are parallel to the mica surface and that the structure of the LPG changes upon addition of Ca{sup 2+}, with an increase in the height of the LPG molecules from the bilayer surface and an almost complete coverage of LPG on the bilayer island.

  8. New construction era reflected in East Texas LPG pipeline

    SciTech Connect (OSTI)

    Mittler, T.J. )

    1990-04-02

    Installation of 240 miles of 6, 10, and 12-in. LPG pipelines from Mont Belvieu to Tyler, Tex., has provided greater feedstock-supply flexibility to a petrochemical plant in Longview, Tex. The project, which took place over 18 months, included tie-ins with metering at four Mont Belvieu suppliers. The new 10 and 12-in. pipelines now transport propane while the new and existing parts of a 6-in. pipeline transport propylene.

  9. Successful operation of a large LPG plant. [Kuwait

    SciTech Connect (OSTI)

    Shtayieh, S.; Durr, C.A.; McMillan, J.C.; Collins, C.

    1982-03-01

    The LPG plant located at Mina-Al Ahmadi, Kuwait, is the heart of Kuwait Oil Co.'s massive Gas Project to use the associated gas from Kuwait's oil production. Operation of this three-train plant has been very successful. A description is given of the three process trains consisting of four basic units: extraction, fractionation, product treating, and refrigeration. Initial problems relating to extraction, fractionation, product treating and, refrigeration are discussed. 1 ref.

  10. Far East LPG sales will grow faster than in West

    SciTech Connect (OSTI)

    1996-12-30

    LPG sales through 2010 in regions east of the Suez Canal (East of Suez) will grow at more than twice those in regions west of the canal. East-of-Suez sales will grow at more than 4.0%/year, compared to slightly less than 2.0%/year growth in sales West of Suez. East-of-Suez sales will reach 92 million tons/year (tpy) by 2010, accounting for 39% of the worldwide total. This share was 31% in1995 and only 27% in 1990. LPG sales worldwide will reach 192 million tons in 2000 and 243 million tpy by 2010. In 1995, they were 163 million tons. These are some of the major conclusions of a recent study by Frank R. Spadine, Christine Kozar, and Rudy Clark of New York City-based consultant Poten and Partners Inc. Details of the study are in the fall report ``World Trade in LPG 1990--2010``. This paper discusses demand segments, seaborne balance, Western sources, largest trading region, North American supplies, and other supplies.

  11. Allocation of energy use in petroleum refineries to petroleum products : implications for life-cycle energy use and emission inventory of petroleum transportation fuels.

    SciTech Connect (OSTI)

    Wang, M.; Lee, H.; Molburg, J.

    2004-01-01

    Studies to evaluate the energy and emission impacts of vehicle/fuel systems have to address allocation of the energy use and emissions associated with petroleum refineries to various petroleum products because refineries produce multiple products. The allocation is needed in evaluating energy and emission effects of individual transportation fuels. Allocation methods used so far for petroleum-based fuels (e.g., gasoline, diesel, and liquefied petroleum gas [LPG]) are based primarily on mass, energy content, or market value shares of individual fuels from a given refinery. The aggregate approach at the refinery level is unable to account for the energy use and emission differences associated with producing individual fuels at the next sub-level: individual refining processes within a refinery. The approach ignores the fact that different refinery products go through different processes within a refinery. Allocation at the subprocess level (i.e., the refining process level) instead of at the aggregate process level (i.e., the refinery level) is advocated by the International Standard Organization. In this study, we seek a means of allocating total refinery energy use among various refinery products at the level of individual refinery processes. We present a petroleum refinery-process-based approach to allocating energy use in a petroleum refinery to petroleum refinery products according to mass, energy content, and market value share of final and intermediate petroleum products as they flow through refining processes within a refinery. The results from this study reveal that product-specific energy use based on the refinery process-level allocation differs considerably from that based on the refinery-level allocation. We calculated well-to-pump total energy use and greenhouse gas (GHG) emissions for gasoline, diesel, LPG, and naphtha with the refinery process-based allocation approach. For gasoline, the efficiency estimated from the refinery-level allocation

  12. Asia, North America lead way in growth of NGL, LPG trade

    SciTech Connect (OSTI)

    Otto, K.; Gist, R.; Whitley, C.; Haun, R.

    1998-01-12

    Recent analyses of world NGL trade indicate that important changes in LPG supply and demand are under way in Asia and North America. LPG markets in the 1990s reflect a rapidly shifting balance between East-of-Suez and West-of-Suez markets. This shift has increased concern about availability of future LPG supplies for Asia. The paper discusses world developments, East versus West of Suez, end uses and supplies in Asia, Canadian ethane, propane, butane, and natural gasoline, Mexican ethane, LPG, and natural gasoline, US ethane, propane, butanes, and iso-C{sub 4} and C{sub 5}.

  13. Cost-effectiveness analysis of TxDOT LPG fleet conversion. Volume 2. Interim research report

    SciTech Connect (OSTI)

    Euritt, M.A.; Taylor, D.B.; Mahmassani, H.

    1992-11-01

    Increased emphasis on energy efficiency and air quality has resulted in a number of state and federal initiatives examining the use of alternative fuels for motor vehicles. Texas' program for alternate fuels includes liquefied petroleum gas (LPG), commonly called propane. Based on an analysis of 30-year life-cycle costs, development of a propane vehicle program for the Texas Department of Transportation (TxDOT) would cost about $24.3 million (in 1991 dollars). These costs include savings from lower-priced propane and differentials between propane and gasoline/diesel in infrastructure costs, vehicle costs, and operating costs. The 30-year life-cycle costs translate into an average annual vehicle cost increase of $308, or about 2.5 cents more per vehicle mile of travel. Based on the cost-effectiveness analysis and assumptions, there are currently no TxDOT locations that can be converted to propane without additional financial outlays. This is volume two of two volumes.

  14. Impact of the revised OSHA exposure standard on evaluation and control of benzene and other volatile organic chemicals in the liquid petroleum pipeline industry

    SciTech Connect (OSTI)

    Mercer, D.O.

    1989-01-01

    The primary purpose of this study was to determine the benzene exposure potential of workers in the liquid petroleum pipeline industry and to assess the impact of compliance with the revised standard on this industry. In addition, exposure to ethylene dibromide (EDB), and ethylene dichloride (EDC), which have toxicological profiles similar to that of benzene and are routinely found in this industry, were evaluated and appropriate control protocols were recommended. Exposure potential to benzene in excess of the 0.5 ppm (8-hour TWA) OSHA action level was shown to be limited to three free product handling operations, and that this increased exposure potential was dependent on the length of time necessary to perform the operations. The incidence and magnitude of benzene overexposure was not severe and control could be accomplished with engineering methods, along with work practice controls and personal protective equipment. Through application of a risk assessment model it was shown that 14 excess leukemia deaths per one thousand workers could be expected in the employee population that routinely performs those operation having maximum benzene exposure potential. This compares to less than on excess leukemia death per one thousand workers in the total work population. The evaluation of EDB and EDC indicated that exposure potential to EDB was of greatest concern. Even though exposure could be limited through application of standard industrial hygiene methods, any control protocol short of total elimination of EDB from the product stream may be not sufficient to reduce exposure to accepted levels.

  15. Petroleum Supply Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    5.PDF Table 15. Natural Gas Plant Net Production and Stocks of Petroleum Products by PAD and Refining Districts, January 2014 (Thousand Barrels) Commodity Production PAD District 1 - East Coast PAD District 2 - Midwest East Coast Appalachian No. 1 Total Indiana, Illinois, Kentucky Minnesota, Wisconsin, North and South Dakota Oklahoma, Kansas, Missouri Total Natural Gas Liquids ................................................ - 4,181 4,181 3,052 1,959 9,877 14,888 Pentanes Plus

  16. Petroleum Supply Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    6.PDF Table 16. Refinery and Blender Net Input of Crude Oil and Petroleum Products by PAD and Refining Districts, January 2014 (Thousand Barrels) Commodity PAD District 1 - East Coast PAD District 2 - Midwest East Coast Appalachian No. 1 Total Indiana, Illinois, Kentucky Minnesota, Wisconsin, North and South Dakota Oklahoma, Kansas, Missouri Total Crude Oil ................................................................. 26,748 2,868 29,616 67,499 14,682 25,866 108,047 Natural Gas Plant Liquids

  17. Petroleum Supply Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    1.PDF Table 31. Exports of Crude Oil and Petroleum Products by PAD District, January 2014 (Thousand Barrels) Commodity PAD Districts U.S. Total 1 2 3 4 5 Total Daily Average Crude Oil 1 ............................................................ 1,496 1,685 4,468 43 6 7,698 248 Natural Gas Plant Liquids and Liquefied Refinery Gases ................................................... 1,533 4,128 12,242 137 456 18,495 597 Pentanes Plus .................................................. 1,190

  18. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    2 June 2016 Table 27. Natural Gas Plant Net Production and Stocks of Petroleum Products by PAD and Refining Districts, June 2016 (Thousand Barrels) Commodity Production PAD District 1 - East Coast PAD District 2 - Midwest East Coast Appalachian No. 1 Total Indiana, Illinois, Kentucky Minnesota, Wisconsin, North and South Dakota Oklahoma, Kansas, Missouri Total Natural Gas Plant Liquids ...................................... 14 9,851 9,865 6,063 6,470 12,522 25,055 Pentanes Plus

  19. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    9 June 2016 Table 49. Exports of Crude Oil and Petroleum Products by PAD District, June 2016 (Thousand Barrels) Commodity PAD Districts U.S. Total 1 2 3 4 5 Total Daily Average Crude Oil 1 ............................................................ 3,576 2,977 4,489 42 406 11,489 383 Natural Gas Plant Liquids and Liquefied Refinery Gases ................................................... 2,704 8,682 21,444 90 1,391 34,311 1,144 Pentanes Plus ..................................................

  20. Urban leakage of liquefied petroleum gas and its potential impact of Mexico City air quality

    SciTech Connect (OSTI)

    Blake, D.R.; Rowland, F.S.

    1995-12-01

    Seventy eight whole air samples were collected at various park locations throughout Mexico City and later assayed for methane, carbon monoxide, 20 halocarbons and 40 C{sub 2}-C{sub 10} hydrocarbons. Propane had the highest median mixing ratio value of all assayed non-methane hydrocarbon compounds (NMHCs) with a concentration as high as 0.1 ppmv. The concentration of n-butane, i-butane, n-pentane and i-pentane were all notably elevated as well. The only significant identified source of propane in Mexico City is liquefied petroleum gas (LPG), which also has a strong component of C{sub 4} and C{sub 5} alkanes. All of these alkanes were present at concentrations well above those observed in other cities where LPG is not the main domestic fuel. Data strongly suggest that as much as 50% of total Mexico City NMHCs is a result of losses associated with the transfer, storage and delivery of LPG. Additionally, using median concentrations and laboratory determined hydroxyl reaction rate constants, LPG emissions account for about 20% of initial reactivities. This suggests that LPG losses may significantly impact photochemical oxidant levels in Mexico City.

  1. Petroleum Marketing Annual Archives

    U.S. Energy Information Administration (EIA) Indexed Site

    Petrolem Reports Petroleum Marketing Annual Archives The Petroleum Marketing Annual was discontinued in 2010. Choose the year from the archive Petroleum Marketing Annual you wish...

  2. Dynamic load measurement on an LPG carrier during voyage

    SciTech Connect (OSTI)

    Kamoi, Noriyuki; Taniguchi, Tomokazu; Kiso, Takashi; Kada, Kazuo; Motoi, Tatsuya; Nakamura, Shinichi

    1994-12-31

    There are few actual ship measurement data showing the propriety of the design loads given by classification societies rules or other relevant rules. Therefore, the authors measured acceleration of ship motion and fluctuating loads on tank supports and chocks of a 75,000 m{sup 3} LPG carrier during her voyage. This paper introduces the subject ship and typical measurement results over about 1.3 years. From the analysis of these data, the authors have made clear the amount of frequency of fluctuating loads during actual navigation and ascertained the propriety of the ship`s design base.

  3. Liquefied Petroleum Gas (LPG) storage facility study, Fort Gordon, Georgia. Final report

    SciTech Connect (OSTI)

    1992-09-01

    Fort Gordon currently purchases natural gas from Atlanta Gas Light Company under a rate schedule for Large Commercial Interruptible Service. This offers a very favorable rate for `interruptible` gas service, however, Fort Gordon must maintain a base level of `firm gas`, purchased at a significantly higher cost, to assure adequate natural gas supplies during periods of curtailment to support family housing requirements and other single fuel users. It is desirable to provide a standby fuel source to meet the needs of family housing and other single fuel users and eliminate the extra costs for the firm gas commitment to Atlanta Gas Light Company. Therefore, a propane-air standby fuel system is proposed to be installed at Fort Gordon.

  4. Liquefied Petroleum Gas (LPG) storage facility study Fort Gordon, Georgia. Final report

    SciTech Connect (OSTI)

    1992-09-01

    Fort Gordon currently purchases natural gas from Atlanta Gas Light Company under a rate schedule for Large Commercial Interruptible Service. This offers a very favorable rate for `interruptible` gas service, however, Fort Gordon must maintain a base level of `firm gas`, purchased at a significantly higher cost, to assure adequate natural gas supplies during periods of curtailment to support family housing requirements and other single fuel users. It is desirable to provide a standby fuel source to meet the needs of family housing and other single fuel users and eliminate the extra costs for the firm gas commitment to Atlanta Gas Light Company. Therefore, a propane-air standby fuel system is proposed to be installed at Fort Gordon.

  5. U.S. Petroleum Flow, 2015

    U.S. Energy Information Administration (EIA) Indexed Site

    Petroleum Flow, 2015 million barrels per day 1 Unfinished oils, hydrogen/oxygenates/renewables/other hydrocarbons, and motor gasoline and aviation gasoline blending components. 2 Renewable fuels and oxygenate plant net production (1.113), net imports (0.654) and adjustments (0.373) minus stock change (0.017) and product supplied (-0.010). 3 Finished petroleum products, liquefied petroleum gases, and pentanes plus. 4 Natural gas plant liquids. 5 Field production (3.273) and renewable fuels and

  6. Conversion of LPG hydrocarbons into distillate fuels using an integral LPG dehydrogenation-MOGD process

    SciTech Connect (OSTI)

    Owen, H.; Zahner, J.C.

    1987-06-23

    This patent describes a process for converting lower paraffinic hydrocarbon feedstock comprising propane and/or butane into heavier hydrocarbons comprising gasoline and distillate, comprising the steps of: feeding the paraffinic feedstock to a dehydrogenation zone under conversion conditions for dehydrogenating at least a portion of the feedstock; recovering a first dehydrogenation gaseous effluent stream comprising propene and/or butene; contacting the first gaseous effluent steam with a liquid lean oil sorbent stream comprising C/sub 5//sup +/ hydrocarbons under sorption conditions to produce a C/sub 3//sup +/ rich liquid absorber stream and a light gas stream; sequentially pressurizing, heating and passing the C/sub 3//sup +/ rich liquid absorber stream to an oligomerization reactor zone at elevated temperature and pressure; contacting the C/sub 3//sup +/ rich stream with oligomerization catalyst in the oligomerization reactor zone for conversion of at least a portion of lower olefins to heavier hydrocarbons under oligomerization reaction conditions to provide a second reactor effluent stream comprising gasoline and distillate boiling range hydrocarbons; flash separating the second reactor effluent stream into a separator vapor stream comprising a major portion of the hydrocarbons which later form the lean oil stream, and a major portion of the C/sub 4//sup -/ hydrocarbons and a separator liquid stream comprising the gasoline and distillate boiling range materials produced in the oligomerization reactor zone; fractionating the separator liquid stream in a first product debutanizer tower into a first debutanizer overhead vapor stream comprising C/sub 4//sup -/ hydrocarbons and a product debutanizer liquid bottoms stream comprising C/sub 5//sup +/ gasoline and distillate boiling range hydrocarbons.

  7. Weekly Petroleum Status Report

    Gasoline and Diesel Fuel Update (EIA)

    Please go to the redesigned Weekly Petroleum Status Report.

  8. Alvord (3000-ft Strawn) LPG flood: design and performance evaluation

    SciTech Connect (OSTI)

    Frazier, G.D.; Todd, M.R.

    1982-01-01

    Mitchell Energy Corporation has implemented a LPG-dry gas miscible process in the Alvord (3000 ft Strawn) Unit in Wise County, Texas utilizing the DOE tertiary incentive program. The field had been waterflooded for 14 years and was producing near its economic limit at the time this project was started. This paper presents the results of the reservoir simulation study that was conducted to evaluate pattern configuration and operating alternatives so as to maximize LPG containment and oil recovery performance. Several recommendations resulting from this study were implemented for the project. Based on the model prediction, tertiary oil recovery is expected to be between 100,000 and 130,000 bbls, or about 7 percent of th oil originally in place in the Unit. An evaluation of the project performance to date is presented. In July of 1981 the injection of a 16% HPV slug of propane was completed. Natural gas is being used to drive the propane slug. A peak oil response of 222 BOPD was achieved in August of 1981 and production has since been declining. The observed performance of the flood indicates that the actual tertiary oil recovered will reach the predicted value, although the project life will be longer than expected. The results presented in this paper indicate that, without the DOE incentive program, the economics for this project would still be uncertain at this time.

  9. New pemex agency, smog checks greet Mexican LPG vehicle users

    SciTech Connect (OSTI)

    Not Available

    1992-10-01

    This paper reports that the relaxation of prohibitions on the use of propane as a motor fuel has spurred sizeable business activity in carburetion and higher demand for LPG throughout Mexico and particularly in Mexico City. However, a number of unforeseen problems have developed that required tough, immediate solutions. After the alternative fuels project began at city hall in Mexico City, publicity spread nationwide, reportedly spurring conversion activity in many other cities. That led to additional demand for fuel of a magnitude that few people had anticipated. In order to assume control of the situation, the national oil company, Pemex, established an official LPG Motor Fuel Department on June 1. Operating in conjunction with the Ministry of Industry, the new department has been busy registering every major propane-powered fleet in the country. Most important, the rate of conversion work must now be pegged to the availability of fuel. It is believed that conversion activity has become more evenly paced since the new Pemex agency took over.over.

  10. This Week In Petroleum Summary Printer-Friendly Version

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    California's ongoing supply disruption (Figure 3). Lower gasoline prices this year are linked to lower crude oil prices. As global petroleum and other liquids production continued...

  11. Total Crude Oil and Petroleum Products Exports

    U.S. Energy Information Administration (EIA) Indexed Site

    Product: Total Crude Oil and Petroleum Products Crude Oil Natural Gas Plant Liquids and Liquefied Refinery Gases Pentanes Plus Liquefied Petroleum Gases Ethane/Ethylene Propane/Propylene Normal Butane/Butylene Isobutane/Isobutylene Other Liquids Hydrogen/Oxygenates/Renewables/Other Hydrocarbons Oxygenates (excl. Fuel Ethanol) Methyl Tertiary Butyl Ether (MTBE) Other Oxygenates Renewable Fuels (incl. Fuel Ethanol) Fuel Ethanol Biomass-Based Diesel Unfinished Oils Naphthas and Lighter Kerosene and

  12. Conversion of LPG hydrocarbons to distillate fuels or lubes using integration of LPG dehydrogenation and mogdl

    SciTech Connect (OSTI)

    Chang, C.D.; Penick, J.E.; Socha, R.F.

    1987-07-07

    This patent describes an apparatus for producing distillates of lubes from paraffins, which comprise: (a) a dehydrogenation reactor including means for passing a paraffinic feedstock stream into a dehydrogenation zone at conditions of pressure and temperature selected to convert the paraffins to an olefin rich effluent stream comprising at least one of the group consisting of propylene and butylene; (b) a low pressure oligomerization catalytic reactor including means for contacting the olefin rich effluent stream in a low pressure oligomerization catalytic reactor zone with a crystalline zeolite oligomerization catalyst at conditions of pressure and temperature selected to convert olefins to a first reactor effluent stream rich in liquid olefinic gasoline range hydrocarbons; (c) a first means for separating the first reactor effluent stream to form a substantially liquid C/sub 5/+ rich stream and a C/sub 4/- rich stream; (d) means for passing the C/sub 5/+ rich stream to a high pressure oligomerization catalytic reactor zone; (e) a high pressure oligomerization catalytic reactor including means for contacting the substantially liquid C/sub 5/+ rich stream in the high pressure oligomerization catalytic reactor zone with a crystalline zeolite oligomerization catalyst at conditions of temperature and pressure selected to produce a second reactor effluent stream which is rich in distillate; (f) second means for separating the second reactor effluent stream to recover an olefinic gasoline stream and a distillate stream; and (g) a hydrotreating reactor including means for contacting the distillate stream with hydrogen in a hydrotreating unit to produce a hydrotreated distillate stream comprising lube range hydrocarbons.

  13. Accuracy of Petroleum Supply Data

    Reports and Publications (EIA)

    2009-01-01

    Accuracy of published data in the Weekly Petroleum Status Report, the Petroleum Supply Monthly, and the Petroleum Supply Annual.

  14. Petroleum Supply Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    5.PDF Table 25. Imports of Crude Oil and Petroleum Products by PAD District, January 2014 (Thousand Barrels, Except Where Noted) Commodity PAD Districts U.S. Total 1 2 3 4 5 Total Daily Average Crude Oil 1,2 ................................................................................. 16,975 63,997 113,277 7,841 33,179 235,269 7,589 Natural Gas Plant Liquids and Liquefied Refinery Gases ...... 2,374 3,314 358 431 234 6,711 216 Pentanes Plus

  15. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    7 June 2016 Table 37. Imports of Crude Oil and Petroleum Products by PAD District, June 2016 (Thousand Barrels, Except Where Noted) Commodity PAD Districts U.S. Total 1 2 3 4 5 Total Daily Average Crude Oil 1,2 ................................................................................. 27,006 56,339 99,092 8,151 37,732 228,320 7,611 Natural Gas Plant Liquids and Liquefied Refinery Gases ...... 839 2,061 43 201 331 3,475 116 Pentanes Plus

  16. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    8 June 2016 Table 38. Year-to-Date Imports of Crude Oil and Petroleum Products by PAD District, January-June 2016 (Thousand Barrels) Commodity PAD Districts U.S. Total 1 2 3 4 5 Total Daily Average Crude Oil 1,2 ............................................................................. 153,535 398,183 603,557 45,937 219,143 1,420,355 7,804 Natural Gas Plant Liquids and Liquefied Refinery Gases .. 8,648 14,318 1,358 2,024 1,851 28,199 155 Pentanes Plus

  17. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    0 June 2016 Table 50. Year-to-Date Exports of Crude Oil and Petroleum Products by PAD District, January-June 2016 (Thousand Barrels) Commodity PAD Districts U.S. Total 1 2 3 4 5 Total Daily Average Crude Oil 1 ............................................................ 27,101 11,565 45,321 2,305 1,319 87,611 481 Natural Gas Plant Liquids and Liquefied Refinery Gases ................................................... 11,668 53,121 146,224 1,006 7,255 219,273 1,205 Pentanes Plus

  18. Century-Midas steps slowly into the RV (recreational vehicles) LPG conversion market

    SciTech Connect (OSTI)

    Kincaid, J.

    1980-02-01

    Midas International will obtain LPG carburetion equipment from Century for installation in up to 20,000 RV. The market for gasoline-powered RV has been depressed since the surge in gasoline prices, and the installation of Century's equipment represents an attempt to attract customers by reducing RV operating costs. According to J. Kincaid (Midas Inst.), propane, besides being cheaper than gasoline, is also cheaper than diesel fuel, despite the better mileage obtained with diesel fuel, because the use of diesel fuel requires the installation of a diesel engine, which is far more expensive than installation of LPG carburetion. Although most of the LPG carburetion manufacturers, with a backlog of orders, did not evince interest in Midas' search for conversion equipment for RV, Century responded, at least partly because Midas also manufactures fleet delivery trucks, which represent a potentially much larger market for LPG conversion and use.

  19. Evaluation of aftermarket LPG conversion kits in light-duty vehicle applications. Final report

    SciTech Connect (OSTI)

    Bass, E.A.

    1993-06-01

    SwRI was contracted by NREL to evaluate three LPG conversion kits on a Chevrolet Lumina. The objective of the project was to measure the Federal Test Procedure (FTP) emissions and fuel economy of these kits, and compare their performance to gasoline-fueled operation and to each other. Varying LPG fuel blends allowed a preliminary look at the potential for fuel system disturbance. The project required kit installation and adjustment according to manufacturer`s instructions. A limited amount of trouble diagnosis was also performed on the fuel systems. A simultaneous contract from the Texas Railroad Commission, in cooperation with NREL, provided funds for additional testing with market fuels (HD5 propane and industry average gasoline) and hydrocarbon (HC) emissions speciation to determine the ozone-forming potential of LPG HC emissions. This report documents the procurement, installation, and testing of these LPG conversion kits.

  20. Product Supplied for Total Crude Oil and Petroleum Products

    U.S. Energy Information Administration (EIA) Indexed Site

    Product: Total Crude Oil and Petroleum Products Crude Oil Natural Gas Liquids and LRGs Pentanes Plus Liquefied Petroleum Gases Ethane/Ethylene Propane/Propylene Normal Butane/Butylene Isobutane/Isobutylene Other Liquids Hydrogen/Oxygenates/Renewables/Other Hydrocarbons Unfinished Oils Motor Gasoline Blend. Comp. (MGBC) MGBC - Reformulated MGBC - Conventional Aviation Gasoline Blend. Comp. Finished Petroleum Products Finished Motor Gasoline Reformulated Gasoline Conventional Gasoline Finished

  1. Petroleum Marketing Annual

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    PDF 1.2MB . Front Matter . Petroleum Marketing Annual Cover Page, Preface, and Table of Contents PDF . Highlights . Petroleum Marketing Annual Highlights PDF . . Summary Statistics ...

  2. Petroleum Marketing Annual

    Gasoline and Diesel Fuel Update (EIA)

    PDF 2.9MB . . Front Matter . Petroleum Marketing Annual Cover Page, Contacts, Preface, and Table of Contents PDF . . Highlights . Petroleum Marketing Annual Highlights PDF . . ...

  3. Petroleum Marketing Annual 1997

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    PDF 1.2MB . . Front Matter . Petroleum Marketing Annual Cover Page, Contacts, Preface, and Table of Contents PDF . . Highlights . Petroleum Marketing Annual Highlights PDF . . ...

  4. Petroleum Marketing Annual 2009

    U.S. Energy Information Administration (EIA) Indexed Site

    Petroleum Marketing Annual 2009 Released: August 6, 2010 Next Release Date: Discontinued find annual data in Petroleum Marketing Monthly Monthly price and volume statistics on...

  5. Petroleum Marketing Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    U.S. Refi ner retail petroleum product prices U.S. Energy Information Administration | Petroleum Marketing Monthly 7 September 2016

  6. Petroleum Marketing Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    U.S. Refi ner retail petroleum product volumes U.S. Energy Information Administration | Petroleum Marketing Monthly 9 September 2016

  7. Petroleum Marketing Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    U.S. Refi ner wholesale petroleum product volumes U.S. Energy Information Administration | Petroleum Marketing Monthly 13 September 20

  8. Petroleum Supply Monthly

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    ... This "green" coke may be sold as is or further purifed by calcining. Petroleum Products. ... products respectively, (including Energy Information AdministrationPetroleum ...

  9. Retraying and revamp double big LPG fractionators's capacity

    SciTech Connect (OSTI)

    Sasson, R. , Friendswood, TX ); Pate, R. )

    1993-08-02

    Enterprise operates two LPG fractionation units at Mont Belvieu: the Seminole unit and the West Texas unit. In 1985, Nye Engineering Inc., Friendswood, Texas, designed improvements to expand the Seminole plant from 60,000 b/d of C[sub 2] + feed to 90,000 b/d. The primary modifications made to increase the West Texas plant's capacity and reduce fuel consumption were the following: retraying the deethanizer and depropanizer columns with new High Capacity Nye Trays. Lowering the pressure in the de-ethanizer and depropanizer to improve the separating efficiency of the columns. Replacing the debutanizer with a high-pressure column that rejects its condensing heat as reboil for the de-ethanizer. Adjusting the feed temperature to balance the load in the top and bottom of the depropanizer column to prevent premature flooding in one section of the tower. Installing convection heaters to recover existing stack gas heat into the process. In conjunction with the capacity expansion, there was a strong incentive to improve the fuel efficiency of the unit. The modifications are described.

  10. Combined application of normal and reversed-phase high-performance liquid chromatography to determining the group composition of aromatic hydrocarbons in petroleum products

    SciTech Connect (OSTI)

    Belous, E.F.; Lanin, S.N.; Nikitin, Yu.S.

    1995-01-01

    The quality and working characteristics of motor fuels essentially depend on the concentration of aromatic hydrocarbons (AHs). Therefore, the development of procedures for the group determination of aromatic hydrocarbons is an important and topical problem in the processing and quality control of petroleum products. The aim of this work was to improve the group separation and quantitative determination of monocyclic and bicyclic aromatic hydrocarbons (MAH and BAH) in light-end products.

  11. Weekly Petroleum Status Report

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    34 A. The Energy Information ... Petroleum Supply Reporting System ......importers, exporters, bulk storage terminals, and pipelines. ...

  12. Petroleum Marketing Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    Crude oil prices U.S. Energy Information Administration | Petroleum Marketing Monthly 3 September 2016

  13. Coal liquefaction and hydroprocessing of petroleum oils

    SciTech Connect (OSTI)

    Rosenthal, J.W.; Dahlberg, A.J.

    1983-12-27

    This invention comprises a process for hydroprocessing a petroleum oil containing soluble metals compounds while suppressing the accumulation of coke within the hydroprocessing zone, comprising the steps of forming a mixture comprising particulate coal and a petroleum oil containing soluble metal compounds to form a feed slurry; and contacting said feed slurry with added hydrogen in said hydroprocessing zone under hydroprocessing conditions to produce an effluent comprising a normally liquid portion having a reduced soluble metals concentration and undissolved solids containing metal from said soluble metals compounds in said petroleum oil.

  14. Determination of combustion products from alternative fuels - part 1. LPG and CNG combustion products

    SciTech Connect (OSTI)

    Whitney, K.A.; Bailey, B.K.

    1994-10-01

    This paper describes efforts underway to identify volatile organic exhaust species generated by a light-duty vehicle operating over the Federal Test Procedure (FTP) on CNG and LPG, and to compare them to exhaust constituents generated from the same vehicle operating on a fuel blended to meet California Phase 2 specifications. The exhaust species from this vehicle were identified and quantified for fuel/air equivalence ratios of 0.8, 1.0, and 1.2, nominally, and were analyzed with and without the vehicle`s catalytic converter in place to determine the influence of the vehicle`s catalyst on species formation. Speciation data showed greater than 87 percent of all LPG and greater than 95 percent of all CNG hydrocarbon exhaust constituents to be composed of C{sub 1} to C{sub 3} compounds. In addition, toxic emissions from the combustion of CNG and LPG were as low as 10 percent of those generated by combustion of gasoline. A comparison of ozone forming potential of the three fuels was made based on the Maximum Incremental Reactivity scale used by the California Air Resources Board. Post-catalyst results from stoichiometric operation indicated that LPG and CNG produced 63 percent and 88 percent less potential ozone than reformulated gasoline, respectively. On average over all equivalence ratios, CNG and LPG exhaust constituents were approximately 65 percent less reactive than those from reformulated gasoline. 4 refs., 3 figs., 14 tabs.

  15. ITP Petroleum Refining: Energy Bandwidth for Petroleum Refining...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Bandwidth for Petroleum Refining Processes ITP Petroleum Refining: Energy Bandwidth for Petroleum Refining Processes bandwidth.pdf (1.16 MB) More Documents & Publications ITP ...

  16. ITP Petroleum Refining: Petroleum Technology Vision 2020 | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Petroleum Technology Vision 2020 ITP Petroleum Refining: Petroleum Technology Vision 2020 techvision.pdf (684.96 KB) More Documents & Publications Manufacturing Energy and Carbon ...

  17. ITP Petroleum Refining: Profile of the Petroleum Refining Industry...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Profile of the Petroleum Refining Industry in California: California Industries of the Future Program ITP Petroleum Refining: Profile of the Petroleum Refining Industry in ...

  18. ITP Petroleum Refining: Energy Efficiency Roadmap for Petroleum...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Efficiency Roadmap for Petroleum Refineries in California ITP Petroleum Refining: Energy Efficiency Roadmap for Petroleum Refineries in California refiningroadmap.pdf (1.34 ...

  19. New and existing gas wells promise bountiful LPG output in Michigan

    SciTech Connect (OSTI)

    Not Available

    1991-01-01

    Michigan remains the leading LP-gas producer in the Northeast quadrant of the U.S. This paper reports that boosted by a number of new natural gas wells and a couple of new gas processing plants, the state is firmly anchored in the butane/propane production business. Since 1981, more than 100 deep gas wells, most in excess of 8000 feet in depth, have been completed as indicated producers in the state. Many of these are yielding LPG-grade stock. So, combined with LPG-grade production from shallower geologic formations, the supply picture in this area looks promising for the rest of the country.

  20. Ageing effect in spray pyrolysed B:SnO{sub 2} thin films for LPG sensing

    SciTech Connect (OSTI)

    Skariah, Benoy E-mail: dr.boben1@gmail.com; Thomas, Boben E-mail: dr.boben1@gmail.com

    2014-10-15

    For LPG sensing, boron doped (0.2 to 0.8 wt. %) polycrystalline tin oxide thin films are deposited by spray pyrolysis in the temperature range 325 - 430 C. Sensor response of 56 % is achieved for 1000 ppm of LPG, at an operating temperature of 350 C. The effects of ageing under ambient conditions on the sensor response are investigated for a storage period of six years. Ageing increases the film resistance but the gas response is lowered. XRD, SEM, FESEM, FTIR and XPS are utilized for structural, morphological and compositional charaterisations.

  1. Petroleum | Open Energy Information

    Open Energy Info (EERE)

    Petroleum (Redirected from Oil) Jump to: navigation, search This article is a stub. You can help OpenEI by expanding it. Petroleum is a fossil fuel consisting of various...

  2. Petroleum Marketing Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    8 Entire . The entire report as a single file. PDF 1.2MB . Front Matter . Petroleum Marketing Annual Cover Page, Preface, and Table of Contents PDF . Highlights . Petroleum...

  3. Petroleum Marketing Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    9 Entire . The entire report as a single file. PDF 1.2MB . Front Matter . Petroleum Marketing Annual Cover Page, Preface, and Table of Contents PDF . Highlights . Petroleum...

  4. Petroleum supply monthly

    SciTech Connect (OSTI)

    Not Available

    1983-05-01

    Information on the supply and distribution of petroleum and petroleum products in the US as of March 1983 is presented. Data include statistics on crude oil, motor gasoline, distillate fuel oil, residual fuel oil, liquefied petroleum gases, imports, exports, stocks, and transport. This issue also features 2 articles entitled: Summer Gasoline Overview and Principal Factors Influencing Motor Gasoline Demand. (DMC)

  5. Petroleum Supply Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    8.PDF Table 38. Movements of Crude Oil and Petroleum Products by Tanker and Barge Between PAD Districts, January 2014 (Thousand Barrels) Commodity From 1 to From 2 to 2 3 5 1 3 5 Crude Oil ................................................................. 106 498 - 223 2,810 - Petroleum Products ............................................... 107 40 0 1,206 2,416 0 Liquefied Petroleum Gases .................................. - 0 - 0 0 - Unfinished Oils

  6. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    6 June 2016 Table 59. Movements of Crude Oil and Petroleum Products by Tanker and Barge Between PAD Districts, June 2016 (Thousand Barrels) Commodity From 1 to From 2 to 2 3 5 1 3 5 Crude Oil ................................................................. 0 0 - 357 848 - Petroleum Products ............................................... 125 0 0 723 2,384 0 Liquefied Petroleum Gases .................................. - 0 - 0 0 - Unfinished Oils

  7. Conception and construction of an LPG tank using a composite membrane technology

    SciTech Connect (OSTI)

    Fuvel, P.; Claude, J.

    1985-03-01

    TECHNIGAZ and TOTAL C.F.P. have developed a new LPG storage technology derived from the membrane concept used for LNG storage and transportation. This technology called GMS uses a composite membrane as primary barrier. A 2 000 m/sup 3/ storage pilot unit, based on that concept, is under construction in TOTAL's refinery at DUNKIRK (France) since September 1983.

  8. This Week In Petroleum Summary Printer-Friendly Version

    Gasoline and Diesel Fuel Update (EIA)

    34.2, the highest in the country last year. (API gravity is an inverse measure of the density of a petroleum liquid relative to water. The higher the number, the lower the density...

  9. This Week In Petroleum Summary Printer-Friendly Version

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    by Saudi Arabia, are continuing the policy of defending market share in a low oil price environment. EIA expects global consumption of petroleum and other liquids to grow by 1.4...

  10. Petroleum marketing monthly

    SciTech Connect (OSTI)

    1995-11-01

    The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data.

  11. Recent advances in the speciation of selenium in petroleum refinery and municipal waste using ICP-MS and ICP-MS coupled with liquid chromatography

    SciTech Connect (OSTI)

    Roehl, R.

    1996-09-01

    An analytical scheme for the speciation of selenium in petroleum refinery waste waters reported at the 1994 Winter Plasma Conference included methods for the determination of total, dissolved, particulate and volatile selenium, as well as for the separate quantitation of dissolved selenite, selenate and selenocyanate. Several of those methods have been improved significantly. Determinations of total, dissolved, and particulate selenium are based on the ICP-MS quantitation of the {sup 82}Se isotope in waste water samples or sample fractions digested with hydrogen peroxide and nitric acid. These analyses now include corrections for potential isobaric interferences are minimized by monitoring the signals for Br{sup +} and m/z 79 and SO{sub 3}H{sup +} at m/z 83 and correcting the apparent {sup 82}Se{sup +} signal using appropriate equations with correction factors derived from the analysis of calibration solutions containing sulfate and bromide. The correction factors used in those equations relate ionic species of different composition to each other (e.g., Br{sup +} and HBr{sup +}). To help ensure that the relative rate of formation of those ions in the plasma is not sample dependent, high concentrations of sodium and other easily ionized elements are removed from the sample digests by cation-exchange.

  12. Safety issues relating to the liquefied petroleum gas, compressed natural gas and liquefied natural gas

    SciTech Connect (OSTI)

    Petru, T.D.

    1995-12-31

    The Railroad Commission of Texas, LP-Gas Division, is statutorily responsible for the safety aspects of liquefied petroleum gas (LPG) most commonly known as LP-gas or propane, compressed natural gas (CNG) and liquefied natural gas (LNG). This presentation will address the safety issues relating to their use as alternative fuels. The paper discusses the safety of pressure vessels used for storage of the fuels at refueling facilities and the containers mounted in vehicles. Other topics include the lack of odorants in LNG, the use of protective clothing when handling cryogenic fluids, and where to obtain a copy of the safety regulations for handling these three fuels.

  13. Petroleum Supply Monthly

    SciTech Connect (OSTI)

    1996-02-01

    The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major U.S. geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

  14. Petroleum supply monthly

    SciTech Connect (OSTI)

    1995-10-01

    The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blends, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

  15. Price Competitive Sale of Strategic Petroleum Reserve Petroleum; Standard

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Sales Provisions; Final Rule | Department of Energy Price Competitive Sale of Strategic Petroleum Reserve Petroleum; Standard Sales Provisions; Final Rule Price Competitive Sale of Strategic Petroleum Reserve Petroleum; Standard Sales Provisions; Final Rule Standard sales provisions for the SPR. Price Competitive Sale of Strategic Petroleum Reserve Petroleum; Standard Sales Provisions; Final Rule (286.15 KB) More Documents & Publications Strategic Petroleum Reserve Test Sale 2014 Report

  16. Petroleum marketing annual 1994

    SciTech Connect (OSTI)

    1995-08-24

    The Petroleum Marketing Annual (PMA) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysis, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the fob and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Annual. For this production, all estimates have been recalculated since their earlier publication in the Petroleum Marketing Monthly (PMM). These calculations made use of additional data and corrections that were received after the PMM publication date.

  17. Waste Heat Powered Ammonia Absorption Refrigeration Unit for LPG Recovery

    SciTech Connect (OSTI)

    Donald C, Energy Concepts Co.; Lauber, Eric, Western Refining Co.

    2008-06-20

    An emerging DOE-sponsored technology has been deployed. The technology recovers light ends from a catalytic reformer plant using waste heat powered ammonia absorption refrigeration. It is deployed at the 17,000 bpd Bloomfield, New Mexico refinery of Western Refining Company. The technology recovers approximately 50,000 barrels per year of liquefied petroleum gas that was formerly being flared. The elimination of the flare also reduces CO2 emissions by 17,000 tons per year, plus tons per year reductions in NOx, CO, and VOCs. The waste heat is supplied directly to the absorption unit from the Unifiner effluent. The added cooling of that stream relieves a bottleneck formerly present due to restricted availability of cooling water. The 350oF Unifiner effluent is cooled to 260oF. The catalytic reformer vent gas is directly chilled to minus 25oF, and the FCC column overhead reflux is chilled by 25oF glycol. Notwithstanding a substantial cost overrun and schedule slippage, this project can now be considered a success: it is both profitable and highly beneficial to the environment. The capabilities of directly-integrated waste-heat powered ammonia absorption refrigeration and their benefits to the refining industry have been demonstrated.

  18. Petroleum marketing monthly

    SciTech Connect (OSTI)

    1996-07-01

    Petroleum Marketing Monthly (PPM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o. b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

  19. Petroleum marketing monthly

    SciTech Connect (OSTI)

    1996-02-01

    The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

  20. Petroleum marketing monthly

    SciTech Connect (OSTI)

    1995-08-01

    The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

  1. Strategic Petroleum Reserve

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Petroleum Reserve Test Sale 2014 Report to Congress November 2014 United States Department of Energy Washington, DC 20585 Strategic Petroleum Reserve Test Sale 2014 Final Report | Page i Message from the Secretary Section 161 of the Energy Policy and Conservation Act (42 U.S.C. 6245), as amended, requires the Secretary of Energy to provide a detailed explanation of any test of the Strategic Petroleum Reserve drawdown and sales procedures. The Department of Energy carried out such a test

  2. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    8 June 2016 Appendix D Northeast Reserves Reserves inventories are not considered to be in the commercial sector and are excluded from EIA's commercial motor gasoline and distillate fuel oil supply and disposition statistics, such as those reported in the Weekly Petroleum Status Report, Petroleum Supply Monthly, and This Week In Petroleum. Northeast Home Heating Oil Reserve classifed as ultra-low sulfur distillate (15 parts per million) Terminal Operator Location Thousand Barrels Buckeye

  3. International petroleum statistics report

    SciTech Connect (OSTI)

    1996-08-01

    This report provides information on current international petroleum production, demand, imports, and stocks. World oil demand and OECD demand data are presented for the years 1970 thru 1995.

  4. Petroleum Supply Monthly

    Gasoline and Diesel Fuel Update (EIA)

    Table 1. U.S. Supply, Disposition, and Ending Stocks of Crude Oil and Petroleum Products, September 2005 (Thousand Barrels) Field Production Refinery and Blender Net Production...

  5. Petroleum | Open Energy Information

    Open Energy Info (EERE)

    Petroleum is a fossil fuel consisting of various hydrocarbons.1 References "http:lsa.colorado.eduessencetextspetroleum.htm" Retrieved from "http:en.openei.orgw...

  6. LPG buses in southern California leave the competition at the curb

    SciTech Connect (OSTI)

    Not Available

    1992-03-01

    This paper reports that after the first year of a landmark experiment in which LPG has been competing against methanol and CNG in city buses, propane appears to be pulling out in front of the pack. According to Efren Medellin, superintendent of vehicle maintenance at the Orange County Transit Authority, two LPG buses had registered a total of 31,000 moles with relatively little, if any, downtime. The two methanol buses had run a total of 30,000 miles while the two CNG buses had traveled only 5000 miles. Furthermore the methanol and CNG buses have had their share of downtime for new parts and other problems. The propane-powered buses appear to be running consistently well without mechanical difficulties. The only problem that occurred was occasional backfiring. As a result, the electronic controls were replaced and no subsequent complaints were heard.

  7. Converting LPG caverns to natural-gas storage permits fast response to market

    SciTech Connect (OSTI)

    Crossley, N.G.

    1996-02-19

    Deregulation of Canada`s natural-gas industry in the late 1980s led to a very competitive North American natural-gas storage market. TransGas Ltd., Regina, Sask., began looking for method for developing cost-effective storage while at the same time responding to new market-development opportunities and incentives. Conversion of existing LPG-storage salt caverns to natural-gas storage is one method of providing new storage. To supply SaskEnergy Inc., the province`s local distribution company, and Saskatchewan customers, TransGas previously had developed solution-mined salt storage caverns from start to finish. Two Regina North case histories illustrate TransGas` experiences with conversion of LPG salt caverns to gas storage. This paper provides the testing procedures for the various caverns, cross-sectional diagrams of each cavern, and outlines for cavern conversion. It also lists storage capacities of these caverns.

  8. Alvord (3,000-ft strawn) LPG flood - design and performance evaluation

    SciTech Connect (OSTI)

    Frazier, G.D.; Todd, M.R.

    1982-01-01

    Mitchell Energy Corporation has implemented a LPG-dry gas miscible process in the Alvord (3000' Strawn) Unit in Wise County, Texas utilizing the DOE tertiary incentive program. The field had been waterflooded for 14 years and was producing near its economic limit at the time this project was started. This paper presents the results of the reservoir simulation study that was conducted to evaluate pattern configuration and operating alternatives so as to maximize LPG containment and oil recovery performance. Several recommendations resulting from this study were implemented for the project. Based on the model predictions, tertiary oil recovery is expected to be between 100,000 and 130,000 bbls, or about 7 percent of the oil originally in place in the Unit. 12 refs.

  9. Cryogenic flexible pipes for offshore LNG-LPG production

    SciTech Connect (OSTI)

    Dumay, J.M.

    1981-01-01

    Available in long, flexible pieces (up to several miles), the high-performance Coflexip pipe comprises four basic layers: (1) an interlocked, spiraled-steel carcass to resist crushing and prevent deformation, (2) an inner thermoplastic sheath to render the line internally leakproof, (3) two cross-laid steel-wire armors to oppose the stresses induced by internal pressure, and (4) an external thermoplastic sheath to ensure water-tightness and resist corrosion. Coflexip pipe is particularly suitable for transporting cryogenic liquids such as LNG from, for example, an offshore liquefaction plant.

  10. Buckley, J.S. 02 PETROLEUM; PETROLEUM; ENHANCED RECOVERY; ASPHALTENES...

    Office of Scientific and Technical Information (OSTI)

    Reservoir Wettability and its Effect on Oil Recovery. Buckley, J.S. 02 PETROLEUM; PETROLEUM; ENHANCED RECOVERY; ASPHALTENES; MINERALS; SURFACES; MICA; WETTABILITY We report on the...

  11. N/sub 2/-driven LPG achieves miscibitity at high temperatures

    SciTech Connect (OSTI)

    Carlisle, L.; Crawford, P.B.; Montes, M. Jr.; Reeves, S.

    1982-11-01

    Shows that miscibility can be achieved at very low pressures above the critical temperature of propane. One can calculate the critical pressure and temperature for a variety of fluids of practical interest in achieving miscibility between the miscible slug and driving gas when applying enhanced oil recovery programs. A study of the critical properties of normally available reservoir fluids indicates that one method of achieving miscibility at lower pressures, even at high reservoir temperatures, might be to use LPG slugs pushed by nitrogen. Table gives the oil recovery for different LPG slug sizes when operating at a reservoir pressure of 2,000 psig and a reservoir temperature of 250F. Diagram shows the approximate critical temperature loci for ternary systems made up of 3 components from the group nitrogen, methane, ethane, and propane. By finding the desired reservoir temperature and then estimating the critical pressure required, one may select compositions and operating pressures required to achieve critical slug-driving gas mixtures for use in enhanced oil recovery programs. When using CO/sub 2/ for miscibility, the miscibility pressure increases with temperature. Use of LPG slugs results in a substantial reduction in the pressure required for miscibility.

  12. Petroleum 1996: Issues and Trends

    Reports and Publications (EIA)

    1997-01-01

    Examines historical trends and focuses on major petroleum issues and the events they represent. It analyzes different dimensions of the petroleum industry and related markets in terms of how they relate to the volatility in petroleum markets.

  13. Petroleum: An Energy Profile 1999

    Reports and Publications (EIA)

    1999-01-01

    Explains in layman's terms the major components and operations of the U.S. petroleum industry that include: petroleum products, resources and reserves, drilling and exploration, refining, storage and transportation, imports, exports, and petroleum marketing.

  14. Petroleum Supply Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    8.PDF Table 28. PAD District 2 - Imports of Crude Oil and Petroleum Products by Country of Origin, January 2014 (Thousand Barrels) Country of Origin Crude Oil 1,2 Pentanes Plus Liquefied Petroleum Gases Unfinished Oils 1 Finished Motor Gasoline Motor Gasoline Blending Components Reform- ulated Conven- tional Total Reform- ulated Conven- tional Total OPEC ..................................... 1,552 - - - - - - - - - Algeria ................................ - - - - - - - - - - Angola

  15. Petroleum Supply Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    0.PDF Table 30. PAD District 4 and 5 - Imports of Crude Oil and Petroleum Products by Country of Origin, January 2014 (Thousand Barrels) Country of Origin Crude Oil 1,2 Pentanes Plus Liquefied Petroleum Gases Unfinished Oils 1 Finished Motor Gasoline Motor Gasoline Blending Components Reform- ulated Conven- tional Total Reform- ulated Conven- tional Total PAD District 4 OPEC ..................................... - - - - - - - - - - Algeria ................................ - - - - - - - - - -

  16. Petroleum Supply Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    2.PDF Table 32. Exports of Crude Oil and Petroleum Products by Destination, January 2014 (Thousand Barrels) Destination Crude Oil 1 Pentanes Plus Liquefied Petroleum Gases Unfinished Oils Finished Motor Gasoline Motor Gasoline Blending Components Reform- ulated Conven- tional Total Reform- ulated Conven- tional Total Argentina ............................ - 0 - 3 - 349 349 - - - Australia .............................. - 0 575 0 - 0 0 - - - Bahamas ............................ - 0 4 - - 179 179

  17. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    1 June 2016 Table 42. PAD District 2 - Imports of Crude Oil and Petroleum Products by Country of Origin, June 2016 (Thousand Barrels) Country of Origin Crude Oil 1,2 Pentanes Plus Liquefied Petroleum Gases Unfinished Oils 1 Finished Motor Gasoline Motor Gasoline Blending Components Reform- ulated Conven- tional Total Reform- ulated Conven- tional Total OPEC ..................................... 801 - - - - - - - - - Algeria ................................ - - - - - - - - - - Angola

  18. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    9 June 2016 Table 44. PAD District 4 and 5 - Imports of Crude Oil and Petroleum Products by Country of Origin, June 2016 (Thousand Barrels) Country of Origin Crude Oil 1,2 Pentanes Plus Liquefied Petroleum Gases Unfinished Oils 1 Finished Motor Gasoline Motor Gasoline Blending Components Reform- ulated Conven- tional Total Reform- ulated Conven- tional Total PAD District 4 OPEC ..................................... - - - - - - - - - - Algeria ................................ - - - - - - - - - -

  19. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    1 June 2016 Table 51. Exports of Crude Oil and Petroleum Products by Destination, June 2016 (Thousand Barrels) Destination Crude Oil 1 Pentanes Plus Liquefied Petroleum Gases Unfinished Oils Finished Motor Gasoline Motor Gasoline Blending Components Reform- ulated Conven- tional Total Reform- ulated Conven- tional Total Argentina ............................ - 0 312 64 - - - - - - Australia .............................. - - 426 - - 0 0 - 0 0 Bahamas ............................ - 0 31 0 - 37 37

  20. Petroleum Reserves | Department of Energy

    Office of Environmental Management (EM)

    the Strategic Petroleum Reserve, the Northeast Home Heating Oil Reserve, and the Northeast Gasoline Supply Reserve. OPR also manages the Naval Petroleum and Oil Shale Reserves. ...

  1. Petroleum supply monthly, April 1994

    SciTech Connect (OSTI)

    Not Available

    1994-04-01

    Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographical regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US. The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the US.

  2. Petroleum Refining | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Energy Efficiency Roadmap for Petroleum Refineries in California (2004) ... Photo credit: iStockphoto.com15906809 Petroleum Refining The United States is the largest, most ...

  3. Petroleum Market Model of the National Energy Modeling System. Part 1

    SciTech Connect (OSTI)

    1997-12-18

    The purpose of this report is to define the objectives of the Petroleum Market Model (PMM), describe its basic approach, and provide detail on how it works. This report is intended as a reference document for model analysts, users, and the public. The PMM models petroleum refining activities, the marketing of petroleum products to consumption regions, the production of natural gas liquids in gas processing plants, and domestic methanol production. The PMM projects petroleum product prices and sources of supply for meeting petroleum product demand. The sources of supply include crude oil, both domestic and imported; other inputs including alcohols and ethers; natural gas plant liquids production; petroleum product imports; and refinery processing gain. In addition, the PMM estimates domestic refinery capacity expansion and fuel consumption. Product prices are estimated at the Census division level and much of the refining activity information is at the Petroleum Administration for Defense (PAD) District level.

  4. Petroleum supply monthly, January 1994

    SciTech Connect (OSTI)

    Not Available

    1994-01-01

    Data presented describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States. The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

  5. Petroleum supply monthly, February 1994

    SciTech Connect (OSTI)

    Not Available

    1994-03-01

    The Petroleum Supply Monthly presents data describing the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US. The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders; operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. Data are divided into two sections: Summary statistics and Detailed statistics.

  6. Petroleum supply monthly, August 1993

    SciTech Connect (OSTI)

    Not Available

    1993-09-01

    This publication the Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report, (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. Data presented are divided into Summary Statistics and Detailed Statistics.

  7. Petroleum Market Model of the National Energy Modeling System

    SciTech Connect (OSTI)

    1997-01-01

    The purpose of this report is to define the objectives of the Petroleum Market Model (PMM), describe its basic approach, and provide detail on how it works. This report is intended as a reference document for model analysts, users, and the public. The PMM models petroleum refining activities, the marketing of petroleum products to consumption regions. The production of natural gas liquids in gas processing plants, and domestic methanol production. The PMM projects petroleum product prices and sources of supply for meeting petroleum product demand. The sources of supply include crude oil, both domestic and imported; other inputs including alcohols and ethers; natural gas plant liquids production; petroleum product imports; and refinery processing gain. In addition, the PMM estimates domestic refinery capacity expansion and fuel consumption. Product prices are estimated at the Census division level and much of the refining activity information is at the Petroleum Administration for Defense (PAD) District level. This report is organized as follows: Chapter 2, Model Purpose; Chapter 3, Model Overview and Rationale; Chapter 4, Model Structure; Appendix A, Inventory of Input Data, Parameter Estimates, and Model Outputs; Appendix B, Detailed Mathematical Description of the Model; Appendix C, Bibliography; Appendix D, Model Abstract; Appendix E, Data Quality; Appendix F, Estimation methodologies; Appendix G, Matrix Generator documentation; Appendix H, Historical Data Processing; and Appendix I, Biofuels Supply Submodule.

  8. Two petroleum additives deals stall on the consolidation trail

    SciTech Connect (OSTI)

    Kiesche, E.S.

    1992-04-22

    The consolidation of the lubricant and fuel additives market is turning out to be anything but a slick transition. Two deals have fallen through since the beginning of April. Ethyl Corp. (Richmond, VA) has discontinued negotiations for the acquisition of BP Chemicals` (London) Adibis petroleum additives business and Lubrizol`s (Wickliffe, OH) proposed purchase of Amoco Chemical`s petroleum additives business is stalled, and may be completely derailed by antitrust concerns. Meanwhile, a third petroleum additives business, the European joint venture between Amoco and Finzis being liquidated.

  9. Petroleum Supply Annual 2014, Volume 1

    U.S. Energy Information Administration (EIA) Indexed Site

    Table 2. U.S. Daily Average Supply and Disposition of Crude Oil and Petroleum Products, 2014 (Thousand Barrels per Day) Commodity Supply Disposition Field Production Renewable Fuels and Oxygenate Plant Net Production Refinery and Blender Net Production Imports Adjust- ments 1 Stock Change 2 Refinery and Blender Net Inputs Exports Products Supplied 3 Crude Oil 4 ............................................................ 8,719 - - - - 7,344 222 86 15,848 351 0 Natural Gas Plant Liquids and

  10. Weekly Petroleum Status Report

    U.S. Energy Information Administration (EIA) Indexed Site

    8 Figure 10. U.S. Average Retail Regular Motor Gasoline and On-Highway Diesel Fuel Prices, January 2015 to Present Note: See Appendix B, Weekly Petroleum Price Surveys, page 40 for ...

  11. Petroleum marketing annual, 1991

    SciTech Connect (OSTI)

    Not Available

    1992-08-01

    The Petroleum Marketing Annual contains statistical data on a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the free-on-board and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented. For this publication, all estimates have been recalculated since their earlier publication in the Petroleum Marketing Monthly (PMM). These calculations made use of additional data and corrections that were received after the PMM publication dates.

  12. Petroleum Marketing Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    5 Entire . The entire report as a single file. PDF 2.9MB . . Front Matter . Petroleum Marketing Annual Cover Page, Contacts, Preface, and Table of Contents PDF . . Highlights ....

  13. Petroleum Marketing Annual 2009

    U.S. Energy Information Administration (EIA) Indexed Site

    cents per gallon to dollars per gallon later this year for the 2010 data. Petroleum Marketing Annual --- Full report in PDF (1.2 MB) Summary Statistics Summary Statistics Tables...

  14. Petroleum Marketing Annual 2008

    U.S. Energy Information Administration (EIA) Indexed Site

    8 Released: August 27, 2009 Petroleum Marketing Annual --- Full report in PDF (1.2 MB) Summary Statistics Summary Statistics Tables PDF 1 Crude Oil Prices PDF TXT 1A Refiner...

  15. Petroleum Marketing Annual 1997

    U.S. Energy Information Administration (EIA) Indexed Site

    7 Entire . The entire report as a single file. PDF 1.2MB . . Front Matter . Petroleum Marketing Annual Cover Page, Contacts, Preface, and Table of Contents PDF . . Highlights ....

  16. Petroleum Marketing Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    6 Entire . The entire report as a single file. PDF 2.9MB . . Front Matter . Petroleum Marketing Annual Cover Page, Contacts, Preface, and Table of Contents PDF . . Highlights ....

  17. Petroleum Marketing Annual 2007

    U.S. Energy Information Administration (EIA) Indexed Site

    7 Released: August 29, 2008 Petroleum Marketing Annual --- Full report in PDF (1.2 MB) Summary Statistics Summary Statistics Tables PDF 1 Crude Oil Prices PDF TXT 1A Refiner...

  18. Petroleum marketing annual 1993

    SciTech Connect (OSTI)

    Not Available

    1995-01-01

    The Petroleum Marketing Annual (PMA) contains statistical data on a variety of crude oils and refined petroleum products. The publication provides statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the free-on-board (f.o.b.) and landed cost of imported crude oil, and the refiners acquisition cost of crude oil. Sales data for motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane are presented. For this publication, all estimates have been recalculated since their earlier publication in the Petroleum Marketing Monthly (PMM). These calculations made use of additional data and corrections that were received after the PMM publication dates.

  19. Weekly Petroleum Status Report

    U.S. Energy Information Administration (EIA) Indexed Site

    Table 4. Stocks of Crude Oil by PAD District, and Stocks of Petroleum Products, 1 U.S. Totals (Million Barrels) Product Region Current Week Last Week Year Ago 2 Years Ago 61716 ...

  20. NAFTA opportunities: Petroleum refining

    SciTech Connect (OSTI)

    Not Available

    1993-01-01

    The North American Free Trade Agreement (NAFTA) creates a more transparent environment for the sale of refined petroleum products to Mexico, and locks in access to Canada's relatively open market for these products. Canada and Mexico are sizable United States export markets for refined petroleum products, with exports of $556 million and $864 million, respectively, in 1992. These markets represent approximately 24 percent of total U.S. exports of these goods.

  1. Petroleum Supply Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    2.PDF Table 22. Refinery Stocks of Crude Oil and Petroleum Products by PAD and Refining Districts, January 2014 (Thousand Barrels) Commodity PAD District 1 - East Coast PAD District 2 - Midwest East Coast Appalachian No. 1 Total Indiana, Illinois, Kentucky Minnesota, Wisconsin, North and South Dakota Oklahoma, Kansas, Missouri Total Crude Oil ..................................................................... 7,495 446 7,941 9,590 1,697 1,988 13,275 Petroleum Products

  2. Petroleum Supply Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    6.PDF Table 26. Imports of Crude Oil and Petroleum Products into the United States by Country of Origin, January 2014 (Thousand Barrels) Country of Origin Crude Oil 1,2 Pentanes Plus Liquefied Petroleum Gases Unfinished Oils 1 Finished Motor Gasoline Motor Gasoline Blending Components Reform- ulated Conven- tional Total Reform- ulated Conven- tional Total OPEC ..................................... 99,127 - - 2,384 - - - - 1,652 1,652 Algeria ................................ - - - 2,119 - - - - -

  3. Petroleum Supply Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    7.PDF Table 27. PAD District 1 - Imports of Crude Oil and Petroleum Products by Country of Origin, January 2014 (Thousand Barrels) Country of Origin Crude Oil 1,2 Pentanes Plus Liquefied Petroleum Gases Unfinished Oils 1 Finished Motor Gasoline Motor Gasoline Blending Components Reform- ulated Conven- tional Total Reform- ulated Conven- tional Total OPEC ..................................... 5,672 - - - - - - - 1,652 1,652 Algeria ................................ - - - - - - - - - - Angola

  4. Petroleum Supply Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    9.PDF Table 29. PAD District 3 - Imports of Crude Oil and Petroleum Products by Country of Origin, January 2014 (Thousand Barrels) Country of Origin Crude Oil 1,2 Pentanes Plus Liquefied Petroleum Gases Unfinished Oils 1 Finished Motor Gasoline Motor Gasoline Blending Components Reform- ulated Conven- tional Total Reform- ulated Conven- tional Total OPEC ..................................... 69,917 - - 2,005 - - - - - - Algeria ................................ - - - 1,740 - - - - - - Angola

  5. Petroleum Supply Annual

    U.S. Energy Information Administration (EIA) Indexed Site

    3.PDF Table 33. Net Imports of Crude Oil and Petroleum Products into the United States by Country, January 2014 (Thousand Barrels per Day) Country of Origin Crude Oil 1 Pentanes Plus Liquefied Petroleum Gases Unfinished Oils Finished Motor Gasoline Motor Gasoline Blending Components Reform- ulated Conven- tional Total Reform- ulated Conven- tional Total OPEC ..................................... 3,198 0 -27 60 - -36 -36 0 52 52 Algeria ................................ - - - 68 - - - - - - Angola

  6. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    3 June 2016 Table 34. Refinery Stocks of Crude Oil and Petroleum Products by PAD and Refining Districts, June 2016 (Thousand Barrels) Commodity PAD District 1 - East Coast PAD District 2 - Midwest East Coast Appalachian No. 1 Total Indiana, Illinois, Kentucky Minnesota, Wisconsin, North and South Dakota Oklahoma, Kansas, Missouri Total Crude Oil ..................................................................... 12,055 729 12,784 10,352 2,180 1,915 14,447 Petroleum Products

  7. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    9 June 2016 Table 39. Imports of Crude Oil and Petroleum Products into the United States by Country of Origin, June 2016 (Thousand Barrels) Country of Origin Crude Oil 1,2 Pentanes Plus Liquefied Petroleum Gases Unfinished Oils 1 Finished Motor Gasoline Motor Gasoline Blending Components Reform- ulated Conven- tional Total Reform- ulated Conven- tional Total OPEC ..................................... 90,723 - - 4,059 - - - - 1,218 1,218 Algeria ................................ 1,253 - - 4,059 -

  8. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    3 June 2016 Table 40. Year-to-Date Imports of Crude Oil and Petroleum Products into the United States by Country of Origin, January-June 2016 (Thousand Barrels) Country of Origin Crude Oil 1,2 Pentanes Plus Liquefied Petroleum Gases Unfinished Oils 1 Finished Motor Gasoline Motor Gasoline Blending Components Reform- ulated Conven- tional Total Reform- ulated Conven- tional Total OPEC ..................................... 563,597 - - 25,955 - 2 2 - 8,201 8,201 Algeria

  9. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    7 June 2016 Table 41. PAD District 1 - Imports of Crude Oil and Petroleum Products by Country of Origin, June 2016 (Thousand Barrels) Country of Origin Crude Oil 1,2 Pentanes Plus Liquefied Petroleum Gases Unfinished Oils 1 Finished Motor Gasoline Motor Gasoline Blending Components Reform- ulated Conven- tional Total Reform- ulated Conven- tional Total OPEC ..................................... 13,026 - - 402 - - - - 522 522 Algeria ................................ - - - 402 - - - - - - Angola

  10. Petroleum Supply Monthly

    U.S. Energy Information Administration (EIA) Indexed Site

    5 June 2016 Table 43. PAD District 3 - Imports of Crude Oil and Petroleum Products by Country of Origin, June 2016 (Thousand Barrels) Country of Origin Crude Oil 1,2 Pentanes Plus Liquefied Petroleum Gases Unfinished Oils 1 Finished Motor Gasoline Motor Gasoline Blending Components Reform- ulated Conven- tional Total Reform- ulated Conven- tional Total OPEC ..................................... 55,521 - - 3,240 - - - - 696 696 Algeria ................................ 1,253 - - 3,240 - - - - - -