Powered by Deep Web Technologies
Note: This page contains sample records for the topic "low-pressure sodium lighting" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Propagation of light in low pressure gas  

E-Print Network [OSTI]

The criticism by W. E. Lamb, W. Schleich, M. Scully, C. Townes of a simplified quantum electrodynamics which represents the photon as a true particle is illustrated. Collisions being absent in low-pressure gas, exchanges of energy are radiative and coherent. Thin shells of plasma containing atoms in a model introduced by Str\\"omgren are superradiant, seen as circles possibly dotted. Spectral radiance of novae has magnitude of laser radiance, and column densities are large in nebulae: Superradiance, multiphoton effects, etc., work in astrophysics. The superradiant beams induce multiphotonic scatterings of light emitted by the stars, brightening the limbs of plasma bubbles and darkening the stars. In excited atomic hydrogen, impulsive Raman scatterings shift frequencies of light. Microwaves exchanged with the Pioneer probes are blueshifted, simulating anomalous accelerations. Substituting coherence for wrong calculations in astrophysical papers, improves results, avoids "new physics".

Jacques Moret-Bailly

2012-04-13T23:59:59.000Z

2

Low-Pressure Sodium Lighting Basics | Department of Energy  

Energy Savers [EERE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of Inspector General Office0-72.pdfGeorgeDoesn't HappenLow-Cost Production of Hydrogen andLow-Costof

3

Low pressure carbonylation of heterocycles  

DOE Patents [OSTI]

Heterocycles, e.g., epoxides, are carbonylated at low pressure with high percentage conversion to cyclic, ring expanded products using the catalyst ##STR00001## where L is tetrahydrofuran (THF).

Coates, Geoffrey W. (Lansing, NY); Kramer, John W. (Mt. Pleasant, MI); Schmidt, Joseph A. R. (Sylvania, OH)

2011-01-25T23:59:59.000Z

4

Sustained Recycle in Light Water and Sodium-Cooled Reactors  

SciTech Connect (OSTI)

From a physics standpoint, it is feasible to sustain recycle of used fuel in either thermal or fast reactors. This paper examines multi-recycle potential performance by considering three recycling approaches and calculating several fuel cycle parameters, including heat, gamma, and neutron emission of fresh fuel; radiotoxicity of waste; and uranium utilization. The first recycle approach is homogeneous mixed oxide (MOX) fuel assemblies in a light water reactor (LWR). The transuranic portion of the MOX was varied among Pu, NpPu, NpPuAm, or all-TRU. (All-TRU means all isotopes through Cf-252.) The Pu case was allowed to go to 10% Pu in fresh fuel, but when the minor actinides were included, the transuranic enrichment was kept below 8% to satisfy the expected void reactivity constraint. The uranium portion of the MOX was enriched uranium. That enrichment was increased (to as much as 6.5%) to keep the fuel critical for a typical LWR irradiation. The second approach uses heterogeneous inert matrix fuel (IMF) assemblies in an LWR - a mix of IMF and traditional UOX pins. The uranium-free IMF fuel pins were Pu, NpPu, NpPuAm, or all-TRU. The UOX pins were limited to 4.95% U-235 enrichment. The number of IMF pins was set so that the amount of TRU in discharged fuel from recycle N (from both IMF and UOX pins) was made into the new IMF pins for recycle N+1. Up to 60 of the 264 pins in a fuel assembly were IMF. The assembly-average TRU content was 1-6%. The third approach uses fast reactor oxide fuel in a sodium-cooled fast reactor with transuranic conversion ratio of 0.50 and 1.00. The transuranic conversion ratio is the production of transuranics divided by destruction of transuranics. The FR at CR=0.50 is similar to the CR for the MOX case. The fast reactor cases had a transuranic content of 33-38%, higher than IMF or MOX.

Steven J. Piet; Samuel E. Bays; Michael A. Pope; Gilles J. Youinou

2010-11-01T23:59:59.000Z

5

Using cavitation to measure statistics of low-pressure events in large-Reynolds-number turbulence  

E-Print Network [OSTI]

Using cavitation to measure statistics of low-pressure events in large-Reynolds-number turbulence A is studied using cavitation. The flow is seeded with microscopic gas bubbles and the hydrostatic pressure is reduced until large negative pressure fluctuations trigger cavitation. Cavitation is detected via light

La Porta, Arthur

6

Sensitivity Analysis of Reprocessing Cooling Times on Light Water Reactor and Sodium Fast Reactor Fuel Cycles  

SciTech Connect (OSTI)

The purpose of this study is to quantify the effects of variations of the Light Water Reactor (LWR) Spent Nuclear Fuel (SNF) and fast reactor reprocessing cooling time on a Sodium Fast Reactor (SFR) assuming a single-tier fuel cycle scenario. The results from this study show the effects of different cooling times on the SFR’s transuranic (TRU) conversion ratio (CR) and transuranic fuel enrichment. Also, the decay heat, gamma heat and neutron emission of the SFR’s fresh fuel charge were evaluated. A 1000 MWth commercial-scale SFR design was selected as the baseline in this study. Both metal and oxide CR=0.50 SFR designs are investigated.

R. M. Ferrer; S. Bays; M. Pope

2008-04-01T23:59:59.000Z

7

Mercury Lamps Recycling Fluorescent light-tubes, compact fluorescent bulbs, mercury and sodium vapor lamps, ultraviolet and  

E-Print Network [OSTI]

Mercury Lamps Recycling Fluorescent light-tubes, compact fluorescent bulbs, mercury and sodium vapor lamps, ultraviolet and HID (high-intensity discharge) lamps and all other mercury containing labeled for shipment to a recycling plant for mercury, glass and aluminum recovery. The beneficial re

Baker, Chris I.

8

Low pressure cooling seal system for a gas turbine engine  

DOE Patents [OSTI]

A low pressure cooling system for a turbine engine for directing cooling fluids at low pressure, such as at ambient pressure, through at least one cooling fluid supply channel and into a cooling fluid mixing chamber positioned immediately downstream from a row of turbine blades extending radially outward from a rotor assembly to prevent ingestion of hot gases into internal aspects of the rotor assembly. The low pressure cooling system may also include at least one bleed channel that may extend through the rotor assembly and exhaust cooling fluids into the cooling fluid mixing chamber to seal a gap between rotational turbine blades and a downstream, stationary turbine component. Use of ambient pressure cooling fluids by the low pressure cooling system results in tremendous efficiencies by eliminating the need for pressurized cooling fluids for sealing this gap.

Marra, John J

2014-04-01T23:59:59.000Z

9

Features of plasma glow in low pressure terahertz gas discharge  

SciTech Connect (OSTI)

Investigations of the low pressure (1–100 Torr) gas discharge in the powerful (1 kW) quasi-optical terahertz (0.55 THz) wave beams were made. An intense afterglow was observed after the end of gyrotron terahertz radiation pulse. Afterglow duration significantly exceeded radiation pulse length (8 ?s). This phenomenon could be explained by the strong dependence of the collisional-radiative recombination rate (that is supposed to be the most likely mechanism of electron losses from the low pressure terahertz gas discharge) on electron temperature.

Bratman, V. L.; Golubev, S. V.; Izotov, I. V.; Kalynov, Yu. K.; Koldanov, V. A.; Razin, S. V. [Institute of Applied Physics, Russian Academy of Sciences, Nizhny Novgorod 603950 (Russian Federation)] [Institute of Applied Physics, Russian Academy of Sciences, Nizhny Novgorod 603950 (Russian Federation); Litvak, A. G.; Sidorov, A. V.; Skalyga, V. A.; Zorin, V. G. [Institute of Applied Physics, Russian Academy of Sciences, Nizhny Novgorod 603950 (Russian Federation) [Institute of Applied Physics, Russian Academy of Sciences, Nizhny Novgorod 603950 (Russian Federation); Lobachevsky State University of Nizhny Novgorod (UNN), 23 Gagarina st., 603950 Nizhny Novgorod (Russian Federation)

2013-12-15T23:59:59.000Z

10

LOW-PRESSURE MEMBRANE CONTACTORS FOR CARBON DIOXIDE CAPTURE  

SciTech Connect (OSTI)

This final technical progress report describes work conducted by Membrane Technology and Research, Inc. (MTR) for the Department of Energy (DOE NETL) on development of low-pressure membrane contactors for carbon dioxide (CO2) capture from power plant flue gas (award number DE-FE0007553). The work was conducted from October 1, 2011 through September 30, 2014. The overall goal of this three-year project was to build and operate a prototype 500 m2 low-pressure sweep membrane module specifically designed to separate CO2 from coal-fired power plant flue gas. MTR was assisted in this project by a research group at the University of Toledo, which contributed to the computational fluid dynamics (CFD) analysis of module design and process simulation. This report details the work conducted to develop a new type of membrane contactor specifically designed for the high-gas-flow, low-pressure, countercurrent sweep operation required for affordable membrane-based CO2 capture at coal power plants. Work for this project included module development and testing, design and assembly of a large membrane module test unit at MTR, CFD comparative analysis of cross-flow, countercurrent, and novel partial-countercurrent sweep membrane module designs, CFD analysis of membrane spacers, design and fabrication of a 500 m2 membrane module skid for field tests, a detailed performance and cost analysis of the MTR CO2 capture process with low-pressure sweep modules, and a process design analysis of a membrane-hybrid separation process for CO2 removal from coal-fired flue gas. Key results for each major task are discussed in the report.

Baker, Richard; Kniep, Jay; Hao, Pingjiao; Chan, Chi Cheng; Nguyen, Vincent; Huang, Ivy; Amo, Karl; Freeman, Brice; Fulton, Don; Ly, Jennifer; Lipscomb, Glenn; Lou, Yuecun; Gogar, Ravikumar

2014-09-30T23:59:59.000Z

11

Method of gettering hydrogen under conditions of low pressure  

DOE Patents [OSTI]

A ternary intermetallic compound having the formula Zr(V.sub.1-x Cr.sub.x).sub.2 where x is in the range of 0.01 to 0.90 is capable of reversibly sorbing hydrogen at temperatures ranging from room temperature to 200.degree. C., at pressures down to 10.sup.-6 Torr. The compound is suitable for use as a hydrogen getter in low pressure, high temperature applications such as magnetic confinement fusion devices.

Mendelsohn, Marshall H. (Woodridge, IL); Gruen, Dieter M. (Downers Grove, IL)

1983-01-01T23:59:59.000Z

12

SMC Lite -- An innovative new low pressure, low density SMC  

SciTech Connect (OSTI)

Two fundamental driving forces in the automotive composites industry are the need to reduce cost and reduce weight. Through a combination of resin chemistry, unique thickening technology and Sheet Molding Compound (SMC) formulation, a method has been developed which yields the reduced sheet viscosity required for low pressure molding (<3.5 MPa versus 9.5 MPa for standard SMC), yet yields a handleable, tack-free sheet. A variation of this new resin technology permits the molding of true Class A panels at 1.6 specific gravity versus 1.9 specific gravity panels molded with traditional SMC.

Taylor, W. [Ashland Chemical Co., Columbus, OH (United States)

1996-11-01T23:59:59.000Z

13

On-Site Wastewater Treatment Systems: Low-Pressure Dosing System  

E-Print Network [OSTI]

A low-pressure dosing system treats wastewater and then pumps it into the soil several times daily. This publication explains the advantages and disadvantages of low-pressure dosing systems as well as estimated costs and maintenance requirements....

Lesikar, Bruce J.

1999-09-06T23:59:59.000Z

14

On-Site Wastewater Treatment Systems: Low-Pressure Dosing System (Spanish)  

E-Print Network [OSTI]

A low-pressure dosing system treats wastewater and then pumps it into the soil several times daily. This publication explains the advantages, disadvantages, maintenance steps and estimated costs of low-pressure dosing systems....

Lesikar, Bruce J.

1999-08-12T23:59:59.000Z

15

Nonequilibrium lighting plasmas  

SciTech Connect (OSTI)

In this paper the science of a variety of devices employing nonequilibrium lighting plasmas is reviewed. The devices include the fluorescent lamp, the low-pressure sodium lamp, the neon sign, ultraviolet lamps, glow indicators, and a variety of devices used by spectroscopists, such as the hollow cathode light source. The plasma conditions in representative commercial devices are described. Recent research on the electron gas, the role of heavy particles, spatial and temporal inhomogeneities, and new electrodeless excitation schemes is reviewed. Areas of future activity are expected to be in new applications of high-frequency electronics to commercial devices, new laser-based diagnostics of plasma conditions, and more sophisticated models requiring more reliable and extensive rate coefficient data.

Dakin, J.T. (GE Lighting, Nela Park, Cleveland, OH (US))

1991-12-01T23:59:59.000Z

16

Very low pressure high power impulse triggered magnetron sputtering  

DOE Patents [OSTI]

A method and apparatus are described for very low pressure high powered magnetron sputtering of a coating onto a substrate. By the method of this invention, both substrate and coating target material are placed into an evacuable chamber, and the chamber pumped to vacuum. Thereafter a series of high impulse voltage pulses are applied to the target. Nearly simultaneously with each pulse, in one embodiment, a small cathodic arc source of the same material as the target is pulsed, triggering a plasma plume proximate to the surface of the target to thereby initiate the magnetron sputtering process. In another embodiment the plasma plume is generated using a pulsed laser aimed to strike an ablation target material positioned near the magnetron target surface.

Anders, Andre; Andersson, Joakim

2013-10-29T23:59:59.000Z

17

Low pressure high speed Stirling air engine. Final technical report  

SciTech Connect (OSTI)

The purpose of this project was to design, construct and test a simple, appropriate technology low pressure, high speed, wood-fired Stirling air engine of 100 W output. The final design was a concentric piston/displacer engine of 454 in. bore and 1 in. stroke with a rhombic drive mechanism. The project engine was ultimately completed and tested, using a propane burner for all tests as a matter of convenience. The 100 W aim was exceeded, at atmospheric pressure, over a wide range of engine speed with the maximum power being 112 W at 1150 rpm. A pressure can was constructed to permit pressurization; however the grant funds were running out, and the only pressurized power test attempted was unsuccessful due to seal difficulties. This was a disappointment because numerous tests on the 4 cubic inch engine suggested power would be more than doubled with pressurization at 25 psig. A manifold was designed and constructed to permit operation of the engine over a standard No. 40 pot bellied stove. The engine was run successfully, but at reduced speed and power, over this stove. The project engine started out being rather noisy in operation, but modifications ultimately resulted in a very quiet engine. Various other difficulties and their solutions also are discussed. (LCL)

Ross, M.A.

1980-06-16T23:59:59.000Z

18

Analysis of Low Pressure Steam Turbine Diffuser and Exhaust Hood Systems.  

E-Print Network [OSTI]

??This thesis concerns the computational modelling of low pressure (LP) steam turbine exhaust hood flows. A test case for LP last stage blades (LSBs) with… (more)

BURTON, ZOE

2014-01-01T23:59:59.000Z

19

Photomicrography for the measurement of steam wetness fraction in low pressure turbines.  

E-Print Network [OSTI]

??The measurement of steam wetness fraction at the exit of a low-pressure (LP) turbine stage is important if the highest turbine performance is to be… (more)

Veeder, Tricia Sue

2012-01-01T23:59:59.000Z

20

Use Steam Jet Ejectors or Thermocompressors to Reduce Venting of Low-Pressure Steam  

SciTech Connect (OSTI)

Industrial Technologies Program's BestPractices tip sheet on improving efficiency of industrial steam systems by recovery latent heat from low-pressure steam.

Not Available

2005-09-01T23:59:59.000Z

Note: This page contains sample records for the topic "low-pressure sodium lighting" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

System and Battery Charge Control for PV-Powered AC Lighting Systems  

SciTech Connect (OSTI)

This report reviews a number of issues specific to stand-alone AC lighting systems. A review of AC lighting technology is presented, which discusses the advantages and disadvantages of various lamps. The best lamps for small lighting systems are compact fluorescent. The best lamps for intermediate-size systems are high- or low-pressure sodium. Specifications for battery charging and load control are provided with the goal of achieving lamp lifetimes on the order of 16,000 to 24,000 hours and battery lifetimes of 4 to 5 years. A rough estimate of the potential domestic and global markets for stand-alone AC lighting systems is presented. DC current injection tests were performed on high-pressure sodium lamps and the test results are presented. Finally, a prototype system was designed and a prototype system controller (with battery charger and DC/AC inverter) was developed and built.

Kern, G.

1999-04-01T23:59:59.000Z

22

Experimental study of the effects of wakes on separation in low pressure turbine flow  

E-Print Network [OSTI]

The present study, which is the first of a series of investigations dealing with specific issues of low pressure turbine (LPT) boundary layer aerodynamics, is aimed at providing a detailed unsteady boundary flow information to understand...

O?ztu?rk, Burak

2003-01-01T23:59:59.000Z

23

Flash High-Pressure Condensate to Regenerate Low-Pressure Steam  

SciTech Connect (OSTI)

This revised ITP tip sheet on regenerating low-pressure steam provides how-to advice for improving industrial steam systems using low-cost, proven practices and technologies.

Not Available

2006-01-01T23:59:59.000Z

24

Bilayer graphene growth by low pressure chemical vapor deposition on copper foil  

E-Print Network [OSTI]

Successfully integrating graphene in standard processes for applications in electronics relies on the synthesis of high-quality films. In this work we study Low Pressure Chemical Vapor Deposition (LPCVD) growth of bilayer ...

Fang, Wenjing, S.M. Massachusetts Institute of Technology

2012-01-01T23:59:59.000Z

25

Use Vapor Recompression to Recover Low-Pressure Waste Steam (Revised0  

SciTech Connect (OSTI)

This revised ITP tip sheet on recovering low-pressure waste steam provides how-to advice for improving industrial steam systems using low-cost, proven practices and technologies.

Not Available

2008-03-01T23:59:59.000Z

26

Kinetics and radiative processes in Xe/I{sub 2} inductively coupled rf discharges at low pressure  

SciTech Connect (OSTI)

The environmental concern over the presence of mercury in conventional fluorescent lamps has motivated research into alternative electrically efficient near UV plasma lighting sources. One such candidate is multi-wavelength UV emission from Xe/I{sub 2} mixtures, including excimer radiation from XeI at 253 nm. Previous studies of the XeI system were performed at high pressures and were intended for laser applications. Practical Xe/I{sub 2} lamps will likely operate in the 0.5--10 torr regime and use electrodeless excitation to avoid issues related to electrode erosion by the halogen. In this paper, the authors report on an experimental investigation of low pressure, inductively coupled plasmas sustained in Xe/I{sub 2} mixtures. The goals of this work are to characterize the UV emission and determine excitation mechanisms in a parameter space of interest to lighting applications.

Barnes, P.N.; Verdeyen, J.T.; Kushner, M.J. [Univ. of Illinois, Urbana, IL (United States). Dept. of Electrical and Computer Engineering

1996-12-31T23:59:59.000Z

27

Characterization of Drip Emitters and Computing Distribution Uniformity in a Drip Irrigation System at Low Pressure Under Uniform Land Slopes  

E-Print Network [OSTI]

Characteristics of emitters under low pressure are essential for designing drip irrigation systems. Low pressure data for drip emitters are not available from manufacturers. A laboratory test was conducted to evaluate the performance of five types...

Dutta, Deba P.

2010-01-15T23:59:59.000Z

28

Demonstration Assessment of Light-Emitting Diode (LED) Street Lighting Host Site: Lija Loop, Portland, Oregon  

SciTech Connect (OSTI)

This report describes the process and results of a demonstration of solid-state lighting (SSL) technology in a residential street lighting application, under the U.S. Department of Energy GATEWAY Solid-State Lighting Technology Demonstration Program. In this project, eight 100W (nominal) high-pressure sodium cobra head fixtures were replaced with a like number of LED street light luminaires manufactured by Leotek, Inc. The Leotek product achieved an estimated payback in the Lija Loop installation of about 20 years for replacement scenarios and a much shorter 7.6 years for new installations. Much of the associated energy savings (55%) supporting these payback periods, however, were achieved by reducing average horizontal photopic illuminance a similar amount (53%). Examined from a different perspective, the measured performance suggests that the Leotek product is at approximate parity with the HPS cobra head in terms of average delivered photopic illumination for a given power consumption. HPS comprises the second most efficacious street lighting technology available, exceeded only by low pressure sodium (LPS). LPS technology is not considered suitable for most street lighting applications due to its monochromatic spectral output and poor color rendering ability; therefore, this LED product is performing at an efficiency level comparable to its primary competition in this application.

Kinzey, Bruce R.; Myer, Michael

2009-11-01T23:59:59.000Z

29

A domain-specific analysis system for examining nuclear reactor simulation data for light-water and sodium-cooled fast reactors  

E-Print Network [OSTI]

Building a new generation of fission reactors in the United States presents many technical and regulatory challenges. One important challenge is the need to share and present results from new high-fidelity, high-performance simulations in an easily usable way. Since modern multiscale, multi-physics simulations can generate petabytes of data, they will require the development of new techniques and methods to reduce the data to familiar quantities of interest (e.g., pin powers, temperatures) with a more reasonable resolution and size. Furthermore, some of the results from these simulations may be new quantities for which visualization and analysis techniques are not immediately available in the community and need to be developed. This paper describes a new system for managing high-performance simulation results in a domain-specific way that naturally exposes quantities of interest for light water and sodium-cooled fast reactors. It describes requirements to build such a system and the technical challenges faced...

Billings, Jay Jay; Hull, S Forest; Lingerfelt, Eric J; Wojtowicz, Anna

2014-01-01T23:59:59.000Z

30

Engine having a high pressure hydraulic system and low pressure lubricating system  

DOE Patents [OSTI]

An engine includes a high pressure hydraulic system having a high pressure pump and at least one hydraulically-actuated device attached to an engine housing. A low pressure engine lubricating system is attached to the engine housing and includes a circulation conduit fluidly connected to an outlet from the high pressure pump.

Bartley, Bradley E. (Manito, IL); Blass, James R. (Bloomington, IL); Gibson, Dennis H. (Chillicothe, IL)

2000-01-01T23:59:59.000Z

31

Radiation transport coupled particle-in-cell simulation of low-pressure inductive discharges  

E-Print Network [OSTI]

Radiation transport coupled particle-in-cell simulation of low-pressure inductive discharges Hae driven by an inductive radio frequency wave are simulated with a one-dimensional radiation transport is self-consistently coupled with plasma dynamics. The radiation efficiency is investigated

Lee, Hae June

32

Alternated high-and low-pressure nitriding of austenitic stainless steel: Mechanisms and results  

E-Print Network [OSTI]

Alternated high- and low-pressure nitriding of austenitic stainless steel: Mechanisms and results G a gas mixture of (N2 /H2):(50/50) in pressure, was applied to stainless-steel AISI 304. In the first or plasma nitriding of metal parts, in par- ticular those made of steel and cast iron, is extensively ap

33

Dynamics of Low-Pressure and High-Pressure Fuel Cell Air Supply System1  

E-Print Network [OSTI]

comparing the low pressure system with the high- pressure system equipped with a high-speed compressor pressure of the FC that is defined as the pressure at which the reactant hydrogen and oxygen (air) are delivered to the FC stack flow fields. In the case of stored compressed hydrogen the pressure of the cathode

Peng, Huei

34

Simulation of subcooled boiling at low pressure conditions with RELAP5-3D computer program  

E-Print Network [OSTI]

. Experimental data from the subcooled boiling experiment at low pressure conditions of Bartel, and Zeitoun and Shoukri were simulated. The RELAP5/MOD3.2 was executed to determine the axial void faction distribution. The predictions of void fraction distributions...

Reza, S.M. Mohsin

2002-01-01T23:59:59.000Z

35

Department of Mechanical Engineering Fall 2011 Pratt & Whitney Engine Low Pressure Turbine Vane Cluster Analysis  

E-Print Network [OSTI]

Turbine Vane Cluster Analysis Overview The goal was to provide Pratt & Whitney with a detailed finitePENNSTATE Department of Mechanical Engineering Fall 2011 Pratt & Whitney ­ Engine Low Pressure 3D cloud data to useable CAD model Use finite element analysis to determine the areas of highest

Demirel, Melik C.

36

Observations of an Impurity-driven Hysteresis Behavior in Ice Crystal Growth at Low Pressure  

E-Print Network [OSTI]

mechanisms for this instability, which can be used to produce clean, faceted ice surfaces. 1 IntroductionObservations of an Impurity-driven Hysteresis Behavior in Ice Crystal Growth at Low Pressure Abstract. We describe observations of a novel hysteresis behavior in the growth of ice crystals under near

Libbrecht, Kenneth G.

37

A Concept for a Low Pressure Noble Gas Fill Intervention in the IFE Fusion Test Facility (FTF) Target Chamber  

SciTech Connect (OSTI)

An engineering evaluation has been initiated to investigate conceptual engineering methods for implementing a viable gas shield strategy in the Fusion Test Facility (FTF) target chamber. The employment of a low pressure noble gas in the target chamber to thermalize energetic helium ions prior to interaction with the wall could dramatically increase the useful life of the first wall in the FTF reactor1. For the purpose of providing flexibility, two target chamber configurations are addressed: a five meter radius sphere and a ten meter radius sphere. Experimental studies at Nike have indicated that a low pressure, ambient gas resident in the target chamber during laser pulsing does not appear to impair the ability of laser light from illuminating targets2. In addition, current investigations into delivering, maintaining, and processing low pressure gas appear to be viable with slight modification to current pumping and plasma exhaust processing technologies3,4. Employment of a gas fill solution for protecting the dry wall target chamber in the FTF may reduce, or possibly eliminate the need for other attenuating technologies designed for keeping He ions from implanting in first wall structures and components. The gas fill concept appears to provide an effective means of extending the life of the first wall while employing mostly commercial off the shelf (COTS) technologies. Although a gas fill configuration may provide a methodology for attenuating damage inflicted on chamber surfaces, issues associated with target injection need to be further analyzed to ensure that the gas fill concept is viable in the integrated FTF design5. In the proposed system, the ambient noble gas is heated via the energetic helium ions produced by target detonation. The gas is subsequently cooled by the chamber wall to approximately 800oC, removed from the chamber, and processed by the chamber gas processing system (CGPS). In an optimized scenario of the above stated concept, the chamber wall acts as the primary heat exchanger. During removal, gas is pumped through the laser ports by turbo molecular-drag pumps (TM-DP). For the purpose of reducing organic based lubricants and seals, a magnetically levitated TM-DP is being investigated with pump manufacturers. Currently, magnetically levitated turbo molecular pumps are commercially available. The pumps will be exposed to thermal loads and ionizing radiation (tritium, Ar-41, post detonation neutrons). Although the TM-DP's will be subjected to these various radiations, current designs for similar pumping devices have been hardened and have the ability of locating control electronics in remote radiation shielded enclosures4. The radiation hardened TM-DP's will be 5 required to operate with minimal maintenance for periods of up to 18 continuous months. As part of this initial investigation for developing a conceptual engineering strategy for a gas fill solution, commercial suppliers of low pressure gas pumping systems have been contacted and engaged in this evaluation. Current technology in the area of mechanical pumping systems indicates that the development of a robust pumping system to meet the requirements of the FTF gas fill concept is within the limits of COTS equipment3,4.

C.A. Gentile, W.R. Blanchard, T.A. Kozub, M. Aristova, C. McGahan, S. Natta, K. Pagdon, J. Zelenty

2010-01-14T23:59:59.000Z

38

Heat pump employing optimal refrigerant compressor for low pressure ratio applications  

DOE Patents [OSTI]

What is disclosed is a heat pump apparatus for conditioning a fluid characterized by a fluid handler for circulating the fluid in heat exchange relationship with a refrigerant fluid; two refrigerant heat exchangers; one for effecting the heat exchange with the fluid and a second refrigerant-heat exchange fluid heat exchanger for effecting a low pressure ratio of compression of the refrigerant; a rotary compressor for compressing the refrigerant with low power consumption at the low pressure ratio; at least one throttling valve connecting at the inlet side of heat exchanger in which liquid refrigerant is vaporized; a refrigerant circuit serially connecting the above elements; refrigerant in the circuit; a source of heat exchange fluid; heat exchange fluid circulating device and heat exchange fluid circuit for circulating the heat exchange fluid in heat exchange relationship with the refrigerant.

Ecker, Amir L. (Dallas, TX)

1982-01-01T23:59:59.000Z

39

Instantaneous and efficient surface wave excitation of a low pressure gas or gases  

DOE Patents [OSTI]

A system for instantaneously ionizing and continuously delivering energy in the form of surface waves to a low pressure gas or mixture of low pressure gases, comprising a source of rf energy, a discharge container, (such as a fluorescent lamp discharge tube), an rf shield, and a coupling device responsive to rf energy from the source to couple rf energy directly and efficiently to the gas or mixture of gases to ionize at least a portion of the gas or gases and to provide energy to the gas or gases in the form of surface waves. The majority of the rf power is transferred to the gas or gases near the inner surface of the discharge container to efficiently transfer rf energy as excitation energy for at least one of the gases. The most important use of the invention is to provide more efficient fluorescent and/or ultraviolet lamps.

Levy, Donald J. (Berkeley, CA); Berman, Samuel M. (San Francisco, CA)

1988-01-01T23:59:59.000Z

40

Effect of shockwave-induced density jump on laser plasma interactions in low-pressure ambient air  

E-Print Network [OSTI]

1 Effect of shockwave-induced density jump on laser plasma interactions in low-pressure ambient air jump were investigated in low- pressure ambient air during the laser pulse using an optical interferometer. A tiny shockwave-induced density jump could be observed clearly in ambient air with pressure

Tillack, Mark

Note: This page contains sample records for the topic "low-pressure sodium lighting" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Downhole steam generator using low-pressure fuel and air supply  

DOE Patents [OSTI]

For tertiary oil recovery, an apparatus for downhole steam generation is designed in which water is not injected directly onto the flame in the combustor, the combustion process is isolated from the reservoir pressure, the fuel and oxidant are supplied to the combustor at relatively low pressures, and the hot exhaust gases is prevented from entering the earth formation but is used to preheat the fuel and oxidant and water. The combustion process is isolated from the steam generation process. (DLC)

Fox, R.L.

1981-01-07T23:59:59.000Z

42

Simplified configuration for the combustor of an oil burner using a low pressure, high flow air-atomizing nozzle  

DOE Patents [OSTI]

The invention relates to clean burning of fuel oil with air. More specifically, to a fuel burning combustion head using a low-pressure, high air flow atomizing nozzle so that there will be a complete combustion of oil resulting in a minimum emission of pollutants. The improved fuel burner uses a low pressure air atomizing nozzle that does not result in the use of additional compressors or the introduction of pressurized gases downstream, nor does it require a complex design. Inventors:

Butcher, Thomas A. (Port Jefferson, NY); Celebi, Yusuf (Middle Island, NY); Fisher, Leonard (Colrain, MA)

2000-09-15T23:59:59.000Z

43

Transient evolution of solitary electron holes in low pressure laboratory plasma  

E-Print Network [OSTI]

Solitary electrons holes (SEHs) are localized electrostatic positive potential structures in collisionless plasmas. These are vortex-like structures in the electron phase space. Its existence is cause of distortion of the electron distribution in the resonant region. These are explained theoretically first time by Schamel et.al [Phys. Scr. 20, 336 (1979) and Phys. Plasmas 19, 020501 (2012)]. Propagating solitary electron holes can also be formed in a laboratory plasma when a fast rising high positive voltage pulse is applied to a metallic electrode [Kar et. al., Phys. Plasmas 17, 102113 (2010)] immersed in a low pressure plasma. The temporal evolution of these structures can be studied by measuring the transient electron distribution function (EDF). In the present work, transient EDF is measured after formation of a solitary electron hole in nearly uniform, unmagnetized, and collisionless plasma for applied pulse width and, where and are applied pulse width and inverse of ion plasma frequency respectively. Fo...

Choudhary, Mangilal; Mukherjee, Subroto

2015-01-01T23:59:59.000Z

44

Study of flow fields induced by surface dielectric barrier discharge actuator in low-pressure air  

SciTech Connect (OSTI)

Surface dielectric barrier discharge (SDBD) is a promising method for a flow control. Flow fields induced by a SDBD actuator driven by the ac voltage in static air at low pressures varying from 1.0 to 27.7?kPa are measured by the particle image velocimetry method. The influence of the applied ac voltage frequency and magnitude on the induced flow fields is studied. The results show that three different classes of flow fields (wall jet flow field, complex flow field, and vortex-shape flow field) can be induced by the SDBD actuator in the low-pressure air. Among them, the wall jet flow field is the same as the tangential jet at atmospheric pressure, which is, together with the vertical jet, the complex flow field. The vortex-shape flow field is composed of one vertical jet which points towards the wall and two opposite tangential jets. The complex and the vortex-shape flow fields can be transformed to the wall jet flow field when the applied ac voltage frequency and magnitude are changed. It is found that the discharge power consumption increases initially, decreases, and then increases again at the same applied ac voltage magnitude when the air pressure decreases. The tangential velocity of the wall jet flow field increases when the air pressure decreases. It is however opposite for the complex flow field. The variation of the applied ac voltage frequency influences differently three different flow fields. When the applied ac voltage magnitude increases at the same applied ac voltage frequency, the maximal jet velocity increases, while the power efficiency increases only initially and then decreases again. The discharge power shows either linear or exponential dependences on the applied ac voltage magnitude.

Che, Xueke, E-mail: chedk@163.com, E-mail: st@mail.iee.ac.cn; Nie, Wansheng; Tian, Xihui; Hou, Zhiyong; He, Haobo; Zhou, Penghui; Zhou, Siyin; Yang, Chao [Equipment Academy, Beijing 101416 (China)] [Equipment Academy, Beijing 101416 (China); Shao, Tao, E-mail: chedk@163.com, E-mail: st@mail.iee.ac.cn [Institute of Electrical Engineering, Chinese Academy of Sciences, Beijing 100190 (China)] [Institute of Electrical Engineering, Chinese Academy of Sciences, Beijing 100190 (China)

2014-04-15T23:59:59.000Z

45

DEVELOPMENT OF A LOW PRESSURE, AIR ATOMIZED OIL BURNER WITH HIGH ATOMIZER AIR FLOW  

SciTech Connect (OSTI)

This report describes technical advances made to the concept of a low pressure, air atomized oil burner for home heating applications. Currently all oil burners on the market are of the pressure atomized, retention head type. These burners have a lower firing rate limit of about 0.5 gallons per hour of oil, due to reliability problems related to small flow passage sizes. High pressure air atomized burners have been shown to be one route to avoid this problem but air compressor cost and reliability have practically eliminated this approach. With the low pressure air atomized burner the air required for atomization can be provided by a fan at 5--8 inches of water pressure. A burner using this concept, termed the Fan-Atomized Burner or FAB has been developed and is currently being commercialized. In the head of the FAB, the combustion air is divided into three parts, much like a conventional retention head burner. This report describes development work on a new concept in which 100% of the air from the fan goes through the atomizer. The primary advantage of this approach is a great simplification of the head design. A nozzle specifically sized for this concept was built and is described in the report. Basic flow pressure tests, cold air velocity profiles, and atomization performance have been measured. A burner head/flame tube has been developed which promotes a torroidal recirculation zone near the nozzle for flame stability. The burner head has been tested in several furnace and boiler applications over the tiring rate range 0.2 to 0.28 gallons per hour. In all cases the burner can operate with very low excess air levels (under 10%) without producing smoke. Flue gas NO{sub x} concentration varied from 42 to 62 ppm at 3% 0{sub 2}. The concept is seen as having significant potential and planned development efforts are discussed.

BUTCHER,T.A.

1998-01-01T23:59:59.000Z

46

Spectroscopic study of unique line broadening and inversion in low-pressure microwave generated water plasmas  

E-Print Network [OSTI]

It was demonstrated that low pressure (~0.2 Torr) water vapor plasmas generated in a 10 mm inner diameter quartz tube with an Evenson microwave cavity show at least two features which are not explained by conventional plasma models. First, significant (> 0.25 nm) hydrogen Balmer_ line broadening, of constant width, up to 5 cm from the microwave coupler was recorded. Only hydrogen, and not oxygen, showed significant line broadening. This feature, observed previously in hydrogen-containing mixed gas plasmas generated with high voltage dc and rf discharges was explained by some researchers to result from acceleration of hydrogen ions near the cathode. This explanation cannot apply to the line broadening observed in the (electrodeless) microwave plasmas generated in this work, particularly at distances as great as 5 cm from the microwave coupler. Second, inversion of the line intensities of both the Lyman and Balmer series, again, at distances up to 5 cm from the coupler, were observed. The line inversion suggest...

Mills, R L; Mayo, R M; Nansteel, M; Dhandapani, B; Phillips, J; Phillips, Jonathan

2004-01-01T23:59:59.000Z

47

Transient growth mechanisms of low Reynolds number flow over a low-pressure turbine blade  

E-Print Network [OSTI]

A direct transient growth analysis for three-dimensional perturbations to flow past a periodic array of T-106/300 low-pressure turbine fan blades is presented. The methodology is based on a singular value decomposition of the flow evolution operator, linearised about a steady or periodic base flow. This analysis yields the optimal growth modes. Previous work on global mode stability analysis of this flow geometry showed the flow is asymptotically stable, indicating a non-modal explanation of transition may be more appropriate. The present work extends previous investigations into the transient growth around a steady base flow, to higher Reynolds numbers and periodic base flows. It is found that the notable transient growth of the optimal modes suggests a plausible route to transition in comparison to modal growth for this configuration. The spatial extent and localisation of the optimal modes is examined and possible physical triggering mechanisms are discussed. It is found that for longer times and longer sp...

Sharma, AS; Sherwin, SJ; Theofilis, V; 10.1007/s00162-010-0183-9

2013-01-01T23:59:59.000Z

48

As-deposited low-strain LPCVD (low-pressure, chemical-vapor-deposition) polysilicon  

SciTech Connect (OSTI)

As-deposited polysilicon films with very low residual strain (lower than 5 x 10/sup -5/) are obtained by a low-pressure, chemical-vapor-deposition (LPCVD) process. Straight polysilicon bridges 300 ..mu..m long, 1.2 ..mu..m thick, and 2 to 20 ..mu..m wide, made using this process. No buckling has been observed in any of the nearly one thousand bridges of this type made in two separate process runs. In addition, no problems of sticking between the bridges and the substrate were encountered with these structures. The polysilicon films from which the beams were fabricated were deposited by pyrolyzing silane at 605/degree/C on a phosphosilicate-glass (PSG) layer (8 wt % P). The PSG layer serves as a sacrificial layer to be subsequently etched away to free the bridge. Our research is aimed at obtaining an understanding of these relationships through consideration of the role of interfacial stresses and the kinetics of initial crystalline nucleation. The technique for producing these low-strain films is significant, however, because no high-temperature annealing steps are required to produce them. 4 refs., 4 figs.

Fan, L.S.; Muller, R.S.

1988-08-01T23:59:59.000Z

49

Exhaust Aftertreatment and Low Pressure Loop EGR Applied to an Off-Highway Engine  

SciTech Connect (OSTI)

The goal of the project was to demonstrate that low pressure loop EGR incorporating a diesel oxidation catalyst (DOC) and a diesel particulate filter (DPF) can be applied to an off-highway engine to meet Tier 3 (Task I) and Interim Tier 4 (Task II) off-road emissions standards. Task I data was collected using a John Deere 8.1 liter engine modified with a low pressure loop EGR system. The engine and EGR system was optimized and final data over the ISO 8178 eight mode test indicated the NOx emissions were less than 4 g/kWh and the PM was less than 0.02 g/kWh which means the engine met the Tier 3 off-road standard. Considerable experimental data was collected and used by Michigan Tech University to develop and calibrate the MTU-Filter 1D DPF model. The MTU-Filter 1D DPF code predicts the particulate mass evolution (deposition and oxidation) in the diesel particulate filter (DPF) during simultaneous loading and during thermal and NO{sub 2}-assisted regeneration conditions. It also predicts the pressure drop across the DPF, the flow and temperature fields, the solid filtration efficiency and the particle number distribution downstream of the DPF. A DOC model was also used to predict the NO{sub 2} upstream of the DPF. The DPF model was calibrated to the experimental data at temperatures from 230 C to 550 C, and volumetric flow rates from 9 to 39 actual m{sup 3}/min. Model predictions of the solid particulate mass deposited in the DPF after each loading and regeneration case were in agreement within +/-10g (or +/-10%) of experimental measurements at the majority of the engine operating conditions. The activation temperatures obtained from the model calibration are in good agreement with values reported in the literature and gave good results in the model calibration by using constant pre-exponential factors throughout the entire range of conditions evaluated. The average clean filter permeability was 2.372 x 10{sup -13} m{sup 2}. Estimates of the solid particulate mass packing density inside the porous wall were 1 to 5 kg/m{sup 3}; and percolation factors were 0.81 to 0.97. Average particulate layer permeability was 1.95 x 10{sup -14} m{sup 2}. Solid particulate layer packing density values were between 11 and 128 kg/m{sup 3}. These values were in good agreement with the Peclet number correlation theory reported in the literature. NO{sub 2}-assisted oxidation of PM in the DPF showed experimentally that a significant reduction of the pressure drop can be achieved (<8 kPa) when sufficient NO{sub 2} (>120 ppm) is available and high exhaust gas temperatures ({approx}360-460 C) can be maintained, even at high PM loadings (low NO{sub 2}/solid PM ratios). The CRT{trademark} (DOC-DPF system) showed limited advantages when used with high PM rates (low NOx/PM ratios) in combination with a low pressure loop EGR strategy for a continuous operation of an engine-exhaust aftertreatment system. The 8.1-liter engine was not designed for low-pressure loop EGR and when the EGR was added the NOx emissions were reduced but the PM emissions increased. This corresponds to the well known NOx to PM relationship in which if the NOx is reduced the PM emissions increase. In order for this technology to be successful on this engine family, the engine out PM emissions must be reduced. These results led to Task II. Task II objective was to meet the interim Tier 4 standards using the CCRT{trademark} technology applied to an advanced 6.8 liter John Deere engine. The advanced engine incorporated a 4 valve head, required additional EGR, an advanced high pressure common rail fuel system and a better matched turbocharger. The EGR system was optimized and the goal of less than 2 g/kWh NOx and less than 0.02 g/kWh PM were achieved over the 8 mode test. Again, experimental data was provided to Michigan Tech to study the passive regeneration of the CCRT{trademark} technology. Two computer models, i.e., the MTU 1-D DOC model and the MTU 1-D 2-layer CPF model were developed as part of this research and calibrated using the data obtained from experiments. The 1-D D

Baumgard, Kirby; Triana, Antonio; Johnson, John; Yang, Song; Premchand, Kiran

2006-01-30T23:59:59.000Z

50

Evaluation of HFC-245ca for commercial use in low pressure chillers. Final report, Volume I  

SciTech Connect (OSTI)

Federal regulations banned the production of CFC-11 on January 1, 1996. HCFC-123, the only commercial alternative, will be limited to service applications after January 1, 2020 and will be eliminated from production on January 1, 2030. HFC-245ca has been identified as a potential replacement for CFC-11 in retrofit applications and for HCFC-123 in new chillers, but the marginal flammability of HFC-245ca is a major obstacle to its commercial use as a refrigerant in the United States. This report assesses the commercial viability of HFC-245ca based on its experimental performance in a direct drive low pressure centrifugal chiller exclusive of its flammability characteristics. Three different impeller diameters were tested in the chiller, with all impellers having identical discharge blade angles. Experimental work included tests in a 200 ton 3 stage direct drive chiller with 3 impeller sets properly sized for each of three refrigerants, CFC-11, HCFC-123, and HFC-245ca. The commercial viability assessment focused on both retrofit and new product performance and cost.

Keuper, E.F. [Trane Co., LaCrosse, WI (United States)] [Trane Co., LaCrosse, WI (United States)

1996-03-01T23:59:59.000Z

51

Effect of confining wall potential on charged collimated dust beam in low-pressure plasma  

SciTech Connect (OSTI)

The effect of confining wall potential on charged collimated dust beam in low-pressure plasma has been studied in a dusty plasma experimental setup by applying electrostatic field to each channel of a multicusp magnetic cage. Argon plasma is produced by hot cathode discharge method at a pressure of 5×10{sup ?4} millibars and is confined by a full line cusped magnetic field confinement system. Silver dust grains are produced by gas-evaporation technique and move upward in the form of a collimated dust beam due to differential pressure maintained between the dust and plasma chambers. The charged grains in the beam after coming out from the plasma column enter into the diagnostic chamber and are deflected by a dc field applied across a pair of deflector plates at different confining potentials. Both from the amount of deflection and the floating potential, the number of charges collected by the dust grains is calculated. Furthermore, the collimated dust beam strikes the Faraday cup, which is placed above the deflector plates, and the current (?pA) so produced is measured by an electrometer at different confining potentials. The experimental results demonstrate the significant effect of confining wall potential on charging of dust grains.

Kausik, S. S.; Kakati, B.; Saikia, B. K. [Centre of Plasma Physics, Institute for Plasma Research, Sonapur 782 402 (India)] [Centre of Plasma Physics, Institute for Plasma Research, Sonapur 782 402 (India)

2013-05-15T23:59:59.000Z

52

Studies on hydrogen plasma and dust charging in low-pressure filament discharge  

SciTech Connect (OSTI)

The effect of working gas pressure and dust charging on electron energy probability function has been studied for hydrogen plasma in a multi-dipole dusty plasma device. A cylindrical Langmuir probe is used to evaluate the plasma parameters and electron energy probability function (EEPF) for different working pressures. For lower energy range (below 10?eV), the EEPF follows a bi-Maxwellian shape at very low pressure (6 × 10{sup ?5}?mbar), while elevating the working pressure up to ?2 × 10{sup ?3} mbar, the shape of the EEPF transforms into a single Maxwellian. Some dip structures are observed at high energy range (??>?10?eV) in the EEPF of hydrogen plasma at all the working conditions. In presence of dust particles, it is observed that the shape of the EEPF changes due to the redistribution of the high and low-energy electron populations. Finally, the effect of working pressure on charge accumulation on dust particles is studied with the help of a Faraday cup and electrometer. From the observations, a strong influence of working pressure on plasma parameters, EEPF and dust charging is observed.

Kakati, B., E-mail: bharatkakati15@gmail.com; Kalita, D.; Kausik, S. S.; Saikia, B. K. [Centre of Plasma Physics, Institute for Plasma Research, Nazirakhat, Sonapur 782 402, Kamrup, Assam (India); Bandyopadhyay, M. [ITER-India, Institute for Plasma Research, Bhat, Gandhinagar 382 428 (India)

2014-08-15T23:59:59.000Z

53

Transport of low pressure electronegative SF{sub 6} plasma through a localized magnetic filter  

SciTech Connect (OSTI)

The generation of an ion-ion plasma where only few electrons are present in the discharge could be appropriated in the context of ion plasma source applications. We present in this paper results obtained with a one-dimensional fluid model in the context of low pressure electronegative SF{sub 6} plasma. Without magnetic field, results show that the electron density is still large in the discharge. With a localized magnetic filter, where the magnetic field strength is such that the transport of the electrons is affected while the transport of ion species remains unmagnetized, we show that a region with a negative–positive ion plasma is found downstream the magnetic filter. The negative ions are produced in the filter due to the decrease of electron temperature. We also find conditions when the plasma sheath near the biased electrode collapses and the negative ion extraction from the plasma becomes possible. In addition, the influence of E?×?B electron transport on the one-dimensional model results is discussed.

Levko, D.; Garrigues, L.; Hagelaar, G. J. M. [LAPLACE (Laboratoire Plasma et Conversion d'Energie), Universite de Toulouse, UPS, INPT Toulouse, 118 route de Narbonne, F-31062 Toulouse Cedex 9, France and CNRS, LAPLACE, F-31062 Toulouse (France)

2014-08-15T23:59:59.000Z

54

Operation of a THGEM-based detector in low-pressure Helium  

E-Print Network [OSTI]

In view of a possible application as a charge-particle track readout for an Active Target Time Projection Chamber (AT-TPC), the operating properties of THick Gaseous Electron Multipliers (THGEM) in pure low-pressure Helium were investigated. This paper includes the effective gain dependence on pressure for different detector configurations (single-, double-, triple-cascade setup), long-term gain stability and energy resolution from tracks of 5.5 MeV alpha particles. Stable operational conditions and maximum detector gains of 10^4-10^7 have been achieved in pure Helium at pressure ranging from 100 torr up to 760 torr. Energy resolution of 6.65% (FWHM) for 690 keV of energy deposited by 5.5 MeV alpha particles at 350 torr was measured. The expected energy resolution for the full track is around 2.4% (FWHM). These results, together with the robustness of THGEM electrodes against spark damage, make THGEM structures highly competitive compared to other technologies considered for TPC applications in an active targ...

Cortesi, Marco; Stolz, Andreas

2015-01-01T23:59:59.000Z

55

2110 IEEE TRANSACTIONS ON PLASMA SCIENCE, VOL. 37, NO. 11, NOVEMBER 2009 Low-Pressure Helicon-Plasma Discharge Initiation  

E-Print Network [OSTI]

flow rates and pressures (en,iz > Lsystem) and high magnetic fields (above the threshold value. INTRODUCTION INITIATION of low-pressure helicon discharges is important for several areas of low-temperature in this paper are available online at http://ieeexplore.ieee.org. Digital Object Identifier 10.1109/TPS.2009

Scharer, John E.

56

aqueous sodium sulfate: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

viscosity, 771, for PDMDAAC fractions in sodium chloride solutions by viscosity, size-exclusionchromatography, and light Dubin, Paul D. 32 Structure and Dynamics in Aqueous...

57

Graphene chemical vapor deposition at very low pressure: The impact of substrate surface self-diffusion in domain shape  

SciTech Connect (OSTI)

The initial stages of graphene chemical vapor deposition at very low pressures (<10{sup ?5?}Torr) were investigated. The growth of large graphene domains (?up to 100??m) at very high rates (up to 3??m{sup 2} s{sup ?1}) has been achieved in a cold-wall reactor using a liquid carbon precursor. For high temperature growth (>900?°C), graphene grain shape and symmetry were found to depend on the underlying symmetry of the Cu crystal, whereas for lower temperatures (<900?°C), mostly rounded grains are observed. The temperature dependence of graphene nucleation density was determined, displaying two thermally activated regimes, with activation energy values of 6?±?1?eV for temperatures ranging from 900?°C to 960?°C and 9?±?1?eV for temperatures above 960?°C. The comparison of such dependence with the temperature dependence of Cu surface self-diffusion suggests that graphene growth at high temperatures and low pressures is strongly influenced by copper surface rearrangement. We propose a model that incorporates Cu surface self-diffusion as an essential process to explain the orientation correlation between graphene and Cu crystals, and which can clarify the difference generally observed between graphene domain shapes in atmospheric-pressure and low-pressure chemical vapor deposition.

Cunha, T. H. R.; Ek-Weis, J.; Lacerda, R. G.; Ferlauto, A. S., E-mail: ferlauto@fisica.ufmg.br [Department of Physics, Federal University of Minas Gerais, Belo Horizonte 31270-901 (Brazil)

2014-08-18T23:59:59.000Z

58

EECBG Success Story: Lighting Retrofit Improving Visibility,...  

Broader source: Energy.gov (indexed) [DOE]

New LED lighting fixtures (right) emit a whiter light than existing high-pressure sodium cobra head streetlights (left) and don't spill light onto nearby houses. | Photos courtesy...

59

Development of a Low Pressure, Air Atomized Oil Burner with High Atomizer Air Flow: Progress Report FY 1997  

SciTech Connect (OSTI)

This report describes technical advances made to the concept of a low pressure, air atomized oil burner for home heating applications. Currently all oil burners on the market are of the pressure atomized, retention head type. These burners have a lower firing rate limit of about 0.5 gallons per hour of oil, due to reliability problems related to small flow passage sizes. High pressure air atomized burners have been shown to be one route to avoid this problem but air compressor cost and reliability have practically eliminated this approach. With the low pressure air atomized burner the air required for atomization can be provided by a fan at 5-8 inches of water pressure. A burner using this concept, termed the Fan-Atomized Burner or ''FAB'' has been developed and is currently being commercialized. In the head of the FAB, the combustion air is divided into three parts, much like a conventional retention head burner. This report describes development work on a new concept in which 100% of the air from the fan goes through the atomizer. The primary advantage of this approach is a great simplification of the head design. A nozzle specifically sized for this concept was built and is described in the report. Basic flow pressure tests, cold air velocity profiles, and atomization performance have been measured. A burner head/flame tube has been developed which promotes a toroidal recirculation zone near the nozzle for flame stability. The burner head has been tested in several furnace and boiler applications over the firing rate range 0.2 to 0.28 gallons per hour. In all cases the burner can operate with very low excess air levels (under 10%) without producing smoke. Flue gas NO{sub x} concentration varied from 42 to 62 ppm at 3% O{sub 2}. The concept is seen as having significant potential and planned development efforts are discussed.

Butcher, T.A.

1998-01-01T23:59:59.000Z

60

Kinetics of wet sodium vapor complex plasma  

SciTech Connect (OSTI)

In this paper, we have investigated the kinetics of wet (partially condensed) Sodium vapor, which comprises of electrons, ions, neutral atoms, and Sodium droplets (i) in thermal equilibrium and (ii) when irradiated by light. The formulation includes the balance of charge over the droplets, number balance of the plasma constituents, and energy balance of the electrons. In order to evaluate the droplet charge, a phenomenon for de-charging of the droplets, viz., evaporation of positive Sodium ions from the surface has been considered in addition to electron emission and electron/ion accretion. The analysis has been utilized to evaluate the steady state parameters of such complex plasmas (i) in thermal equilibrium and (ii) when irradiated; the results have been graphically illustrated. As a significant outcome irradiated, Sodium droplets are seen to acquire large positive potential, with consequent enhancement in the electron density.

Mishra, S. K., E-mail: nishfeb@rediffmail.com [Institute for Plasma Research (IPR), Gandhinagar 382428 (India); Sodha, M. S. [Centre of Energy Studies, Indian Institute of Technology Delhi (IITD), New Delhi 110016 (India)] [Centre of Energy Studies, Indian Institute of Technology Delhi (IITD), New Delhi 110016 (India)

2014-04-15T23:59:59.000Z

Note: This page contains sample records for the topic "low-pressure sodium lighting" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Microstructural aspects of low-pressure plasma-sprayed CoNiCrAlY coating on Hastelloy X  

SciTech Connect (OSTI)

A Co-32Ni-21Cr-8Al-0.5Y alloy coating plasma sprayed on Hastelloy X. The microstructure of the coating layer consist of ..gamma.. phase solid solution, ..gamma..' phase, and Y-rich intermetallic phase. This coating exhibits excellent oxidation and sulfidation resistance after exposure in air and in sodium sulfate at 1,000/sup 0/C for 60 h, due to the formation of ..cap alpha..-Al/sub 2/O/sub 3/ oxide scale. However, the presence of chloride in the sodium sulfate leads to rupture of the aluminium oxide scale, and this results in the precipitation of chlorides and sulfides within the coating layer.

Tjong, S.C.; Shih, G.E.; Ho, N.J.

1989-01-01T23:59:59.000Z

62

Experimental and numerical investigations of electron density in low-pressure dual-frequency capacitively coupled oxygen discharges  

SciTech Connect (OSTI)

The electron density is measured in low-pressure dual-frequency (2/60 MHz) capacitively coupled oxygen discharges by utilizing a floating hairpin probe. The dependence of electron density at the discharge center on the high frequency (HF) power, low frequency (LF) power, and gas pressure are investigated in detail. A (1D) particle-in-cell/Monte Carlo method is developed to calculate the time-averaged electron density at the discharge center and the simulation results are compared with the experimental ones, and general agreements are achieved. With increasing HF power, the electron density linearly increases. The electron density exhibits different changes with the LF power at different HF powers. At low HF powers (e.g., 30 W in our experiment), the electron density increases with increasing LF power while the electron density decreases with increasing LF power at relatively high HF powers (e.g., 120 W in our experiment). With increasing gas pressure the electron density first increases rapidly to reach a maximum value and then decreases slowly due to the combined effect of the production process by the ionization and the loss processes including the surface and volume losses.

Liu, Jia; Wen, De-Qi; Liu, Yong-Xin; Gao, Fei; Lu, Wen-Qi; Wang, You-Nian [School of Physics and Optoelectronic Technology, Dalian University of Technology, Dalian 116024 (China)] [School of Physics and Optoelectronic Technology, Dalian University of Technology, Dalian 116024 (China)

2013-11-15T23:59:59.000Z

63

Gasoline from coal in the state of Illinois: feasibility study. Volume I. Design. [KBW gasification process, ICI low-pressure methanol process and Mobil M-gasoline process  

SciTech Connect (OSTI)

Volume 1 describes the proposed plant: KBW gasification process, ICI low-pressure methanol process and Mobil M-gasoline process, and also with ancillary processes, such as oxygen plant, shift process, RECTISOL purification process, sulfur recovery equipment and pollution control equipment. Numerous engineering diagrams are included. (LTN)

Not Available

1980-01-01T23:59:59.000Z

64

Laboratory tests to evaluate and study formation damage with low-density drill-in fluids (LDDIF) for horizontal well completions in low pressure and depleted reservoirs  

E-Print Network [OSTI]

The increasing number of open hole horizontal well completions in low-pressure and depleted reservoirs requires the use of non-damaging low-density drill-in fluids (LDDIF) to avoid formation damage and realize optimum well productivity. To address...

Chen, Guoqiang

2002-01-01T23:59:59.000Z

65

Manufacturing and properties of newly developed 9%CrMoVNiNbN high-pressure low-pressure rotor shaft forging  

SciTech Connect (OSTI)

In order to obtain the improved strength and toughness for high-pressure low-pressure rotor shaft forging, fundamental studies using laboratory heats were performed on the 9CrMoV base materials, and effects of chemistry on toughness and creep rupture strength were investigated. From the investigation, it is showed that the superclean 9CrMoVNiNbN steel with reduced Si and Mn contents and Ni addition provides a superior strength versus toughness balance. Based on these fundamental studies, a trial high-pressure low-pressure rotor shaft forging with diameter of low-pressure section of 1,750 mm and diameter of high-pressure section of 1,200 mm was successfully manufactured from the diameter of 1,800 mm, and the weight of 65 ton ESR ingot. From the evaluation test results of this trial rotor forging, homogeneous distribution of chemistry was confirmed and low impurity contents was observed in the whole forging. The superior strength and toughness were confirmed with good creep rupture strength. The FATT at the center of low-pressure section was {minus}3 C with the tensile strength level of 870 MPa. From the results of fracture toughness test, low cycle fatigue test, and isothermal aging test, superior mechanical properties were demonstrated. Thus, the superclean 9CrMoVNiNbN steel with reduced Si and Mn contents and Ni addition, is particularly suitable for the high-pressure low-pressure rotor material for advanced combined cycle power plants.

Azuma, Tsukasa; Tanaka, Yasuhiko; Ishiguro, Tohru; Yoshida, Hajime; Ikeda, Yasumi [Japan Steel Works, Muroran (Japan)

1997-12-31T23:59:59.000Z

66

Investigation of effect of excitation frequency on electron energy distribution functions in low pressure radio frequency bounded plasmas  

SciTech Connect (OSTI)

Particle in cell (PIC) simulations are employed to investigate the effect of excitation frequency {omega} on electron energy distribution functions (EEDFs) in a low pressure radio frequency (rf) discharge. The discharge is maintained over a length of 0.10 m, bounded by two infinite parallel plates, with the coherent heating field localized at the center of the discharge over a distance of 0.05 m and applied perpendicularly along the y and z directions. On varying the excitation frequency f (={omega}/2{pi}) in the range 0.01-50 MHz, it is observed that for f {<=} 5 MHz the EEDF shows a trend toward a convex (Druyvesteyn-like) distribution. For f > 5 MHz, the distribution resembles more like a Maxwellian with the familiar break energy visible in most of the distributions. A prominent ''hot tail'' is observed at f{>=} 20 MHz and the temperature of the tail is seen to decrease with further increase in frequency (e.g., at 30 MHz and 50 MHz). The mechanism for the generation of the ''hot tail'' is considered to be due to preferential transit time heating of energetic electrons as a function of {omega}, in the antenna heating field. There exists an optimum frequency for which high energy electrons are maximally heated. The occurrence of the Druyvesteyn-like distributions at lower {omega} may be explained by a balance between the heating of the electrons in the effective electric field and elastic cooling due to electron neutral collision frequency {nu}{sub en}; the transition being dictated by {omega} {approx} 2{pi}{nu}{sub en}.

Bhattacharjee, Sudeep [Space plasma, Power and Propulsion, Research School of Physics and Engineering, Australian National University, Canberra ACT 0200 (Australia); Department of Physics, Indian Institute of Technology, Kanpur 208 016 (India); Lafleur, Trevor; Charles, Christine; Boswell, Rod [Space plasma, Power and Propulsion, Research School of Physics and Engineering, Australian National University, Canberra ACT 0200 (Australia)

2011-07-15T23:59:59.000Z

67

Submersible sodium pump  

DOE Patents [OSTI]

An electromagnetic submerged pump has an outer cylindrical stator with an inner cylindrical conductive core for the submerged pumping of sodium in the cylindrical interstitial volume defined between the stator and core. The cylindrical interstitial volume is typically vertically oriented, and defines an inlet at the bottom and an outlet at the top. The outer stator generates upwardly conveyed toroidal magnetic fields, which fields convey preferably from the bottom of the pump to the top of the pump liquid sodium in the cold leg of a sodium cooled nuclear reactor. The outer cylindrical stator has a vertically disposed duct surrounded by alternately stacked layers of coil units and laminates. 14 figs.

Brynsvold, G.V.; Lopez, J.T.; Olich, E.E.; West, C.W.

1989-11-21T23:59:59.000Z

68

46th Street Pilot Street Lighting Project  

E-Print Network [OSTI]

Street to 48th Street) as standard high-pressure sodium (HPS) lighting comparison corridor #12;The over time #12;Initial Lighting Comparison #12;Lighting Project Location #12;Street Light Layout 3046th Street Pilot Street Lighting Project A Joint Venture: Hennepin County & City of Minneapolis

Minnesota, University of

69

Department of Defense/Department of Energy joint demilitarization technology demonstration program executive summary of Phase II demonstrations: The low-pressure rocket motor burns in X-Tunnel  

SciTech Connect (OSTI)

Three low-pressure rocket motor burn tests were executed in May--June 1997 time frame at the X-tunnel complex located on the Department of Energy's Nevada Test Site.

B. W. Bellow; A. E. Moeller; D. Steele; S. M. Williams; R. L. Heinle; C. O. Pruneda; C. A. Velsko; B. E. Watkins; C. J. Hewitt; H. Fry; J. A. Sanchez; J. R. Stephens; J. R. Carson; W. C. Gray; W. C. Thomas; T. J. Tope; S. W. Allendorf; L. R. Carrillo; H. H. Hirano; H. A. Johnsen; J. Lipkin; D. K. Ottesen; R. L. Peabody; C. R. Shaddix; J. C. Swearengen; R. F. Boehm; A. Smiecinski; K. J. Stetzenback

1999-12-01T23:59:59.000Z

70

Pulsed CO{sub 2} laser with an X-ray preioniser based on a high-voltage low-pressure glow discharge  

SciTech Connect (OSTI)

An X-ray preioniser with an electron beam energy density of 0.1 J cm{sup -2} based on a high-voltage (20 - 40 kV) low-pressure glow discharge is developed for repetitively pulsed gas lasers. The electron concentration in the CO{sub 2} - N{sub 2} - He mixture as a function of the voltage across the preioniser is calculated for titanium and other foils. The preioniser can be operated both in a single-pulse regime and at pulse repetition rates ranging up to hundreds of Hertz. A specific energy yield of 51 J L{sup -1} is achieved in the X-ray preionised pulsed CO{sub 2} atmospheric-pressure laser. This preioniser was shown to be efficient for other active media (CO and excimer lasers), which opens up new opportunities for the development of repetitively pulsed gas lasers. (lasers)

Oreshkin, V F; Seregin, Aleksandr M; Sinaiskii, V V; Shchetinkina, T A ['Astrofizika' Research and Production Association (Russian Federation); Sorokin, A R [Institute of Semiconductor Physics, Siberian Branch of the Russian Academy of Sciences, Novosibirsk (Russian Federation)

2003-12-31T23:59:59.000Z

71

1-Dodecane-sulfonic-acid-sodium-salt(LAS) assisted hydrothermal synthesis of Cd{sub x}Zn{sub 1-x}S solid solution as efficient photocatalysts under visible light irradiation  

SciTech Connect (OSTI)

With anionic surfactant LAS assisted, series of zinc cadmium sulfide semiconductor photocatalysts were synthesized by hydrothermal method. These products were characterized by X-ray diffraction (XRD), UV-Vis absorption spectra (UV-Vis) and scanning electron microscopy (FESEM). The photocatalytic activities of as-prepared samples were evaluated by photocatalytic hydrogen production from water under visible-light irradiation. The best synthesis parameters are: Composition 0.9:0.1 (Cd:Zn molar ratio), Temperature 160 deg. C, Hydrothermal Time 48 Hour, LAS Concentration 1.7 mmol/L, the maximum visible-light-catalytic hydrogen production rate is 161.25 {mu}mol/h (lambda>430 nm) which is higher than those of by coprecipitation method. The experiment results indicate that surfactant assisted hydrothermal method is an effective way to get highly active CdZnS solid solution photocatalyst.

Jia, B.; Guo, L. J. [State Key Laboratory of Multiphase Flow in power Engineering, Xi'an Jiaotong University (China)

2010-03-01T23:59:59.000Z

72

ID-69 Sodium drain experiments  

SciTech Connect (OSTI)

This paper describes experiments to determine the sodium retention and drainage from the two key areas of an ID-69. This information is then used as the initiation point for guidelines of how to proceed with washing an ID-69 in the IEM Cell Sodium Removal System.

Johnston, D.C.

1996-09-19T23:59:59.000Z

73

Sodium loop framework structural analysis  

SciTech Connect (OSTI)

This document provides the structural analysis of the Sodium Loop framework in a drop condition. The drop is similar to the US Department of Transportation non-bulk, performance-oriented packaging (Packaging Group I) drop test. The drop height evaluated for the Sodium Loop framework is 5.9 ft.

Nguyen, P.M.

1995-06-06T23:59:59.000Z

74

Tables of thermodynamic properties of sodium  

SciTech Connect (OSTI)

The thermodynamic properties of saturated sodium, superheated sodium, and subcooled sodium are tabulated as a function of temperature. The temperature ranges are 380 to 2508 K for saturated sodium, 500 to 2500 K for subcooled sodium, and 400 to 1600 K for superheated sodium. Tabulated thermodynamic properties are enthalpy, heat capacity, pressure, entropy, density, instantaneous thermal expansion coefficient, compressibility, and thermal pressure coefficient. Tables are given in SI units and cgs units.

Fink, J.K.

1982-06-01T23:59:59.000Z

75

Practical features of illumination with high pressure sodium lamps  

SciTech Connect (OSTI)

A number of concerns raised about the health effects of high pressure sodium lamps (HPS) are discussed. The notion of a ''natural'' human photic environment based on sunlight is disputed. Humans are better adapted to the ''greenish'' spectral composition of forest light than to direct sunlight. It is ironic that the artificial light source which has received the most disapproval, cool white flourescent lamp, has a spectral composition similar to that of forest light. HPS is also available in a full range of colors. Some successful examples of HPS--from North Division High School, in Milwaukee, Wisconsin, to museum exhibits at National Geographic in Washington--are listed.

Corth, R.

1983-06-01T23:59:59.000Z

76

Independent Oversight Review, Sodium Bearing Waste Treatment...  

Energy Savers [EERE]

Federal - June 2012 Independent Oversight Review, Sodium Bearing Waste Treatment Project - Federal - June 2012 June 2012 Review of the Sodium Bearing Waste Treatment Project -...

77

Independent Oversight Review, Sodium Bearing Waste Treatment...  

Energy Savers [EERE]

Contractor - June 2012 Independent Oversight Review, Sodium Bearing Waste Treatment Project - Contractor - June 2012 June 2012 Review of the Sodium Bearing Waste Treatment Project...

78

Simulation of sodium boiling experiments with THERMIT sodium version  

E-Print Network [OSTI]

Natural and forced convection experiments(SBTF and French) are simulated with the sodium version of the thermal-hydraulic computer code THERMIT. Simulation is done for the test secti- -on with the pressure-velocity boundary ...

Huh, Kang Yul

1982-01-01T23:59:59.000Z

79

Investigation of the effects of a thin dielectric layer on low-pressure hydrogen capacitive discharges driven by combined radio frequency and pulse power sources  

SciTech Connect (OSTI)

Negative hydrogen ion sources, for instance for fusion devices, currently attract considerable attention. To generate the precursors—highly rovibrationally excited hydrogen molecules—for negative hydrogen ions effectively by electron excitation, a thin dielectric layer is introduced to cover the surface of the electrically grounded electrode of two parallel metal plates in a low-pressure hydrogen capacitive discharge driven by combined rf and pulse power sources. To understand the characteristics of such discharges, particle-in-cell simulations are conducted to study the effects that the single dielectric layer would bring onto the discharges. The simulation results show that the dielectric layer leads to a much higher plasma density and a much larger production rate of highly vibrationally excited hydrogen molecules compared to discharges without the dielectric layer on the electrode. Further investigation indicates that the nonlinear oscillation of the electrons induced by the nanosecond-pulse continues until it is finally damped down and does not show any dependence on the pulse plateau-time, which is in stark contrast to the case without the dielectric layer present. The physical reason for this phenomenon is explored and explained.

Sun, Jizhong; Fan, Yu; Zou, Ying; Wang, Dezhen [Key Laboratory of Materials Modification by Laser, Ion and Electron Beams (Ministry of Education), School of Physics and Optoelectronic Technology, Dalian University of Technology, Dalian 116024 (China)] [Key Laboratory of Materials Modification by Laser, Ion and Electron Beams (Ministry of Education), School of Physics and Optoelectronic Technology, Dalian University of Technology, Dalian 116024 (China); Stirner, Thomas [Department of Electronic Engineering, University of Applied Sciences Deggendorf, Edlmairstr. 6-8, D-94469 Deggendorf (Germany)] [Department of Electronic Engineering, University of Applied Sciences Deggendorf, Edlmairstr. 6-8, D-94469 Deggendorf (Germany)

2013-11-15T23:59:59.000Z

80

Creep-rupture behavior of seven iron-base alloys after long term aging at 760/sup 0/C in low pressure hydrogen  

SciTech Connect (OSTI)

Candidate iron-base alloys for heater tube application in the Stirling automotive engine were aged at 760/sup 0/C for 3500 h in a low pressure argon or hydrogen atmosphere to determine the effect on mechanical behavior. The seven alloys evaluated were N-155, 19-9DL, 316SS, Nitronic 40, A286, Incoloy 800H, and RA330. Aging produced no appreciable changes in alloy grain size but did promote increased density and growth of precipitate particles in the grains and grain boundaries. Tensile properties were generally degraded by aging, with ductility and strength changes being influenced by grain structure. Aging also decreased creep-rupture strength, with coarse grain materials being more susceptible to strength loss. The presence of hydrogen during aging did not contribute significantly to creep strength degradation in the coarse grain alloys but did result in extensive strength losses in fine grain alloys. Based on current criteria for the Mod I Stirling engine, the N-155 and 19-9DL alloys were the only alloys in this study with strengths adequate for heater tube service at 760/sup 0/C.

Witzke, W.R.; Stephens, J.R.

1980-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "low-pressure sodium lighting" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Surface-Driven Sodium Ion Energy Storage in Nanocellular Carbon...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Surface-Driven Sodium Ion Energy Storage in Nanocellular Carbon Foams. Surface-Driven Sodium Ion Energy Storage in Nanocellular Carbon Foams. Abstract: Sodium ion (Na+) batteries...

82

anticoagulant sodium citrate: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

pressure-velocity boundary ... Huh, Kang Yul 1982-01-01 38 Ground beef shelf life assessment as influenced by sodium lactate, sodium propionate, sodium diacetate, and soy...

83

Fire suppressing apparatus. [sodium fires  

DOE Patents [OSTI]

Apparatus for smothering a liquid sodium fire comprises a pan, a perforated cover on the pan, and tubed depending from the cover and providing communication between the interior of the pan and the ambient atmosphere through the perforations in the cover. Liquid caught in the pan rises above the lower ends of the tubes and thus serves as a barrier which limits the amount of air entering the pan.

Buttrey, K.E.

1980-12-19T23:59:59.000Z

84

Commercial Lighting  

Broader source: Energy.gov [DOE]

Commercial lighting accounts for more than 20 percent of total commercial building energy use. The Energy Department works to reduce lighting energy use through research and deployment.

85

Electrodeless lighting RF power source development. Final report  

SciTech Connect (OSTI)

An efficient, solid state RF power source has been developed on this NICE project for exciting low power electrodeless lamp bulbs. This project takes full advantage of concurrent advances in electrodeless lamp technology. Electrodeless lamp lighting systems utilizing the sulfur based bulb type developed by Fusion Lighting, Inc., is an emerging technology which is based on generating light in a confined plasma created and sustained by RF excitation. The bulb for such a lamp is filled with a particular element and inert gas at low pressure when cold. RF power from the RF source creates a plasma within the bulb which reaches temperatures approaching those of high pressure discharge lamp plasmas. At these temperatures the plasma radiates substantial visible light with a spectrum similar to sunlight.

NONE

1996-08-30T23:59:59.000Z

86

Continuous-wave sodium D2 resonance radiation generated in single-pass sum-frequency  

E-Print Network [OSTI]

-frequency generation. The demonstrated conversion efficiency is 3.2% W-1 cm-1 . This compact solid-state light source applications involving the high- resolution sodium spectrum, including laser remote sensing, biology, communications, display technology [1], and Bose­Einstein condensation [2]. A narrow- band solid-state source

87

Independent Oversight Assessment, Idaho Cleanup Project Sodium...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Bearing Waste Treatment Project - November 2012 November 2012 Assessment of Nuclear Safety Culture at the Idaho Cleanup Project Sodium Bearing Waste Treatment Project This...

88

TOXICOLOGICAL AND STRUCTURAL CONSEQUENCES FROM SODIUM-WATER REACTION IN CELL CONTAINING THE SECONDARY SODIUM TANK  

SciTech Connect (OSTI)

The analysis will show the consequences should the solid sodium in the Secondary Sodium Tank react with a presumed layer of water in the cell. The Peer Review Checklist is attached.

MARUSICH RM

2008-06-25T23:59:59.000Z

89

A layered sodium titanate as promising anode material for sodium ion batteries  

E-Print Network [OSTI]

Sodium ion batteries have recently received great attention for large-scale energy applications because of the abundance and low cost of sodium source. Although some cathode materials with desirable electrochemical properties ...

Wu, Di, S.M. Massachusetts Institute of Technology

2014-01-01T23:59:59.000Z

90

Electrolytic process to produce sodium hypochlorite using sodium ion conductive ceramic membranes  

DOE Patents [OSTI]

An electrochemical process for the production of sodium hypochlorite is disclosed. The process may potentially be used to produce sodium hypochlorite from seawater or low purity un-softened or NaCl-based salt solutions. The process utilizes a sodium ion conductive ceramic membrane, such as membranes based on NASICON-type materials, in an electrolytic cell. In the process, water is reduced at a cathode to form hydroxyl ions and hydrogen gas. Chloride ions from a sodium chloride solution are oxidized in the anolyte compartment to produce chlorine gas which reacts with water to produce hypochlorous and hydrochloric acid. Sodium ions are transported from the anolyte compartment to the catholyte compartment across the sodium ion conductive ceramic membrane. Sodium hydroxide is transported from the catholyte compartment to the anolyte compartment to produce sodium hypochlorite within the anolyte compartment.

Balagopal, Shekar; Malhotra, Vinod; Pendleton, Justin; Reid, Kathy Jo

2012-09-18T23:59:59.000Z

91

E-Print Network 3.0 - aqueous sodium dodecyl Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

of Sodium Dodecyl Sulfate and Sodium Dodecyl Benzenesulfonate on Poly(Vinyl Chloride) Latexes Summary: 1 Adsorption of Sodium Dodecyl Sulfate and Sodium Dodecyl...

92

Atlas Sodium Automated Batch Synthesis System  

E-Print Network [OSTI]

Atlas Sodium Automated Batch Synthesis System (Syrris) June 2013 #12;Introduction to the system · The Atlas Sodium system consists of an Atlas base equipped with a 400ºC hotplate, a stacking dry bath systemL) for automated addition and/or removal of solution. · The system is computer controlled by the Atlas software

Subramanian, Venkat

93

Sodium Heat Engine Development Program  

SciTech Connect (OSTI)

The Sodium Heat Engine (SHE) is an efficient thermoelectric conversion device which directly generates electricity from a thermally regenerative electrochemical cell that relies on the unique conduction properties of {beta}{double prime}-alumina solid electrolyte (BASE). Laboratory models of a variety of SHE devices have demonstrated the feasibility and efficiency of the system, engineering development of large prototype devices has been slowed by a series of materials and fabrication problems. Failure of the electrolyte tubes has been a recurring problem and a number of possible causes have been postulated. To address these issues, a two-phase engineering development program was undertaken. This report summarizes the final results of the first phase of the program, which included extensive materials characterization activities, a study of applicable nondestructive evaluation methods, an investigation of possible stress states that would contribute to fracture, and certain operational issues associated with the electromagnetic pumps used in the SHE prototype. Mechanical and microstructural evaluation of commercially obtained BASE tubes revealed that they should be adequate for SHE applications and that sodium exposure produced no appreciable deleterious strength effects. Processing activities to produce a more uniform and smaller grain size for the BASE tubes were completed using isostatic pressing, extrusion, and slip casting. Green tubes were sintered by conventional and microwave plasma methods. Of particular interest is the residual stress state in the BASE tubes, and both analysis and nondestructive evaluation methods were employed to evaluate these stresses. X-ray and neutron diffraction experiments were performed to determine the bulk residual stresses in commercially fabricated BASE tubes; however, tube-to-tube variations and variations among the various methods employed did not allow formulation of a definitive definition of the as-fabricated stress state.

Singh, J.P.; Kupperman, D.S.; Majumdar, S.; Dorris, S.; Gopalsami, N.; Dieckman, S.L.; Jaross, R.A.; Johnson, D.L.; Gregar, J.S.; Poeppel, R.B.; Raptis, A.C.; Valentin, R.A.

1992-01-01T23:59:59.000Z

94

In-situ method for treating residual sodium  

SciTech Connect (OSTI)

A unique process for deactivating residual sodium in Liquid Metal Fast Breeder Reactor (LMFBR) systems which uses humidified (but not saturated) carbon dioxide at ambient temperature and pressure to convert residual sodium into solid sodium bicarbonate.

Sherman, Steven R. (Idaho Falls, ID); Henslee, S. Paul (Idaho Falls, ID)

2005-07-19T23:59:59.000Z

95

In-Situ Method for Treating Residual Sodium  

DOE Patents [OSTI]

A unique process for deactivating residual sodium in Liquid Metal Fast Breeder Reactor (LMFBR) systems which uses humidified (but not saturated) carbon dioxide at ambient temperature and pressure to convert residual sodium into solid sodium bicarbonate.

Sherman, Steven R.; Henslee, S. Paul

2005-07-19T23:59:59.000Z

96

Smart Lighting Controller!! Smart lighting!  

E-Print Network [OSTI]

1! Smart Lighting Controller!! #12;2! Smart lighting! No need to spend energy lighting the room if://blogs.stthomas.edu/realestate/2011/01/24/residential-real-estate-professionals-how-do-you- develop feedback! There is a connection between the output and the input! Therefore forces inputs to same voltage

Anderson, Betty Lise

97

SciTech Connect: Thermodynamic and transport properties of sodium...  

Office of Scientific and Technical Information (OSTI)

on thermophysical properties of sodium have been included in this critical assessment. Thermodynamic properties of sodium liquid and vapor that have been assessed...

98

A resting bottom sodium cooled fast reactor  

SciTech Connect (OSTI)

This follows ICAPP 2011 paper 11059 'Fast Reactor with a Cold Bottom Vessel', on sodium cooled reactor vessels in thermal gradient, resting on soil. Sodium is frozen on vessel bottom plate, temperature increasing to the top. The vault cover rests on the safety vessel, the core diagrid welded to a toric collector forms a slab, supported by skirts resting on the bottom plate. Intermediate exchangers and pumps, fixed on the cover, plunge on the collector. At the vessel top, a skirt hanging from the cover plunges into sodium, leaving a thin circular slit partially filled by sodium covered by argon, providing leak-tightness and allowing vessel dilatation, as well as a radial relative holding due to sodium inertia. No 'air conditioning' at 400 deg. C is needed as for hanging vessels, and this allows a large economy. The sodium volume below the slab contains isolating refractory elements, stopping a hypothetical corium flow. The small gas volume around the vessel limits any LOCA. The liner cooling system of the concrete safety vessel may contribute to reactor cooling. The cold resting bottom vessel, proposed by the author for many years, could avoid the complete visual inspection required for hanging vessels. However, a double vessel, containing support skirts, would allow introduction of inspecting devices. Stress limiting thermal gradient is obtained by filling secondary sodium in the intermediate space. (authors)

Costes, D. [Consultant (France)

2012-07-01T23:59:59.000Z

99

Commercial Lighting and LED Lighting Incentives  

Broader source: Energy.gov [DOE]

Incentives for energy efficient commercial lighting equipment as well as commercial LED lighting equipment are available to businesses under the Efficiency Vermont Lighting and LED Lighting...

100

IAEA sodium void reactivity benchmark calculations  

SciTech Connect (OSTI)

In this paper, the IAEA-1 992 ``Benchmark Calculation of Sodium Void Reactivity Effect in Fast Reactor Core`` problem is evaluated. The proposed design is a large axially heterogeneous oxide-fueled fast reactor as described in Section 2; the core utilizes a sodium plenum above the core to enhance leakage effects. The calculation methods used in this benchmark evaluation are described in Section 3. In Section 4, the calculated core performance results for the benchmark reactor model are presented; and in Section 5, the influence of steel and interstitial sodium heterogeneity effects is estimated.

Hill, R.N.; Finck, P.J.

1992-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "low-pressure sodium lighting" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

IAEA sodium void reactivity benchmark calculations  

SciTech Connect (OSTI)

In this paper, the IAEA-1 992 Benchmark Calculation of Sodium Void Reactivity Effect in Fast Reactor Core'' problem is evaluated. The proposed design is a large axially heterogeneous oxide-fueled fast reactor as described in Section 2; the core utilizes a sodium plenum above the core to enhance leakage effects. The calculation methods used in this benchmark evaluation are described in Section 3. In Section 4, the calculated core performance results for the benchmark reactor model are presented; and in Section 5, the influence of steel and interstitial sodium heterogeneity effects is estimated.

Hill, R.N.; Finck, P.J.

1992-01-01T23:59:59.000Z

102

Lighting Renovations  

Broader source: Energy.gov [DOE]

When undertaking a lighting renovation in a Federal building, daylighting is the primary renewable energy opportunity. Photovoltaics (PV) also present an excellent opportunity. While this guide...

103

Cerenkov Light  

ScienceCinema (OSTI)

The bright blue glow from nuclear reactors is Cerenkov light. Karl Slifer describes how nuclear physicists can use this phenomenon to study the nucleus of the atom.

Slifer, Karl

2014-05-22T23:59:59.000Z

104

Cerenkov Light  

SciTech Connect (OSTI)

The bright blue glow from nuclear reactors is Cerenkov light. Karl Slifer describes how nuclear physicists can use this phenomenon to study the nucleus of the atom.

Slifer, Karl

2013-06-13T23:59:59.000Z

105

Radial power flattening in sodium fast reactors  

E-Print Network [OSTI]

In order to improve a new design for a uranium startup sodium cooled fast reactor which was proposed at MIT, this thesis evaluated radial power flattening by varying the fuel volume fraction at a fixed U-235 enrichment of ...

Krentz-Wee, Rebecca (Rebecca Elizabeth)

2012-01-01T23:59:59.000Z

106

Sodium Alanate Nanoparticles for Hydrogen Storage.  

E-Print Network [OSTI]

??Preparation and characterization of sodium alanate (NaAlH4) based hydrogen storage materials are described in this book. The effect of the NaAlH4 particle size, particularly in… (more)

Baldé, C.P.

2008-01-01T23:59:59.000Z

107

The Sodium Process Facility at Argonne National Laboratory-West  

SciTech Connect (OSTI)

Argonne National Laboratory-West (ANL-W) has approximately 680,000 liters of raw sodium stored in facilities on site. As mandated by the State of Idaho and the US Department of Energy (DOE), this sodium must be transformed into a stable condition for land disposal. To comply with this mandate, ANL-W designed and built the Sodium Process Facility (SPF) for the processing of this sodium into a dry, sodium carbonate powder. The major portion of the sodium stored at ANL-W is radioactively contaminated. The sodium will be processed in three separate and distinct campaigns: the 290,000 liters of Fermi-1 primary sodium, the 50,000 liters of the Experimental Breeder Reactor-II (EBR-II) secondary sodium, and the 330,000 liters of the EBR-II primary sodium. The Fermi-1 and the EBR-II secondary sodium contain only low-level of radiation, while the EBR-II primary sodium has radiation levels up to 0.5 mSv (50 mrem) per hour at 1 meter. The EBR-II primary sodium will be processed last, allowing the operating experience to be gained with the less radioactive sodium prior to reacting the most radioactive sodium. The sodium carbonate will be disposed of in 270 liter barrels, four to a pallet. These barrels are square in cross-section, allowing for maximum utilization of the space on a pallet, minimizing the required landfill space required for disposal.

Michelbacher, J.A.; Henslee, S.P. McDermott, M.D.; Price, J.R.; Rosenberg, K.E.; Wells, P.B.

1998-07-01T23:59:59.000Z

108

LEDs for Energy Efficient Greenhouse Lighting  

E-Print Network [OSTI]

Light energy is an important factor for plant growth. In regions where the natural light source, i.e. solar radiation, is not sufficient for growth optimization, additional light sources are being used. Traditional light sources such as high pressure sodium lamps and other metal halide lamps are not very efficient and generate high radiant heat. Therefore, new sustainable solutions should be developed for energy efficient greenhouse lighting. Recent developments in the field of light source technologies have opened up new perspectives for sustainable and highly efficient light sources in the form of light-emitting diodes, i.e. LEDs, for greenhouse lighting. This review focuses on the potential of LEDs to replace traditional light sources in the greenhouse. In a comparative economic analysis of traditional vs. LED lighting, we show that the introduction of LEDs allows reduction of the production cost of vegetables in the long-run of several years, due to the high energy efficiency, low maintenance cost and lon...

Singh, Devesh; Meinhardt-Wollweber, Merve; Roth, Bernhard

2014-01-01T23:59:59.000Z

109

Method and system for producing hydrogen using sodium ion separation membranes  

DOE Patents [OSTI]

A method of producing hydrogen from sodium hydroxide and water is disclosed. The method comprises separating sodium from a first aqueous sodium hydroxide stream in a sodium ion separator, feeding the sodium produced in the sodium ion separator to a sodium reactor, reacting the sodium in the sodium reactor with water, and producing a second aqueous sodium hydroxide stream and hydrogen. The method may also comprise reusing the second aqueous sodium hydroxide stream by combining the second aqueous sodium hydroxide stream with the first aqueous sodium hydroxide stream. A system of producing hydrogen is also disclosed.

Bingham, Dennis N; Klingler, Kerry M; Turner, Terry D; Wilding, Bruce M; Frost, Lyman

2013-05-21T23:59:59.000Z

110

Low pressure combustor for generating steam downhole  

SciTech Connect (OSTI)

A compact catalytic combustor for generating steam downhole in an oil reservoir has steam generating tubes that are attached to a metal catalyst support. The metal support comprises sheets of metal that are spaced apart and transverse to the tubes. Heat from combustion is generated on the metal sheets and is conducted to the steam generating tubes. The steam is injected into the oil reservoir. The combustion gas is vented to ground level.

Retallick, W.B.

1983-03-22T23:59:59.000Z

111

Low pressure noncryogenic processing for ethylene recovery  

SciTech Connect (OSTI)

This patent describes a process for recovering ethylene from a hydrocarbon gas feed stream containing components selected from the group consisting of hydrogen, nitrogen, methane, carbon monoxide, at least 5 mol % of ethylene, ethane, heavier saturated and unsaturated hydrocarbons and mixtures. It comprises: countercurrently contacting the hydrocarbon gas feed stream with a lean physical solvent. It comprises paraffinic solvents; naphthenic solvents; benzene, toluene, C{sub 8}--C{sub 10} aromatic compounds; dialkyl ethers of polyalkylene glycol; regenerating the ethylene rich solvent in a distillation column equipped with at least one reflux condenser and at least one reboiler to produce ethylene plus hydrocarbon product as an overhead stream and the lean physical solvent as a bottom stream, the ethylene plus hydrocarbon product being suitable for bypassing a downstream demethanizer.

Mehrta, Y.R.

1991-05-28T23:59:59.000Z

112

Light Computing  

E-Print Network [OSTI]

A configuration of light pulses is generated, together with emitters and receptors, that allows computing. The computing is extraordinarily high in number of flops per second, exceeding the capability of a quantum computer for a given size and coherence region. The emitters and receptors are based on the quantum diode, which can emit and detect individual photons with high accuracy.

Gordon Chalmers

2006-10-13T23:59:59.000Z

113

In sodium tests of ultrasonic transducers  

SciTech Connect (OSTI)

Ultrasonic techniques are seen as suitable candidates for the in-service inspection and for the continuous surveillance of sodium cooled reactors (SFR). These techniques need the development and the qualification of immersed ultrasonic transducers, and materials. This paper presents some developments performed by CEA (DTN and LIST) and AREVA (NDE Solutions), and some results. (authors)

Lhuillier, C.; Descombin, O.; Baque, F. [CEA, DTN, 13108 Saint Paul lez Durance Cedex (France); Marchand, B. [CEA, LIST, 91191 Gif-sur-Yvette (France); Saillant, J. F. [AREVA/NDE Solutions, 4 rue Thomas Dumorey, 71109 Chalon sur Saone Cedex (France); Augem, J. M. [EDF, 12-14 avenue Dutrievoz, 69628 Villeurbanne (France)

2011-07-01T23:59:59.000Z

114

Gypsum and Polyacrylamide Soil Amendments Used With High Sodium Wastewater  

E-Print Network [OSTI]

Using wastewater for irrigation of crops represents an attractive alternative to disposal. Typically, municipal wastewaters are high in sodium, and the resulting high sodium absorption ratio (SAR) alters the soil structure making it more impermeable...

Gardiner, Duane

115

Prediction of slug-to-annular flow pattern transition (STA) for reducing the risk of gas-lift instabilities and effective gas/liquid transport from low-pressure reservoirs  

SciTech Connect (OSTI)

Flow-pattern instabilities have frequently been observed in both conventional gas-lifting and unloading operations of water and oil in low-pressure gas and coalbed reservoirs. This paper identifies the slug-to-annular flow-pattern transition (STA) during upward gas/liquid transportation as a potential cause of flow instability in these operations. It is recommended that the slug-flow pattern be used mainly to minimize the pressure drop and gas compression work associated with gas-lifting large volumes of oil and water. Conversely, the annular flow pattern should be used during the unloading operation to produce gas with relatively small amounts of water and condensate. New and efficient artificial lifting strategies are required to transport the liquid out of the depleted gas or coalbed reservoir level to the surface. This paper presents held data and laboratory measurements supporting the hypothesis that STA significantly contributes to flow instabilities and should therefore be avoided in upward gas/liquid transportation operations. Laboratory high-speed measurements of flow-pressure components under a broad range of gas-injection rates including STA have also been included to illustrate the onset of large STA-related flow-pressure oscillations. The latter body of data provides important insights into gas deliquification mechanisms and identifies potential solutions for improved gas-lifting and unloading procedures. A comparison of laboratory data with existing STA models was performed first. Selected models were then numerically tested in field situations. Effective field strategies for avoiding STA occurrence in marginal and new (offshore) field applications (i.e.. through the use of a slug or annular flow pattern regimen from the bottomhole to wellhead levels) are discussed.

Toma, P.R.; Vargas, E.; Kuru, E.

2007-08-15T23:59:59.000Z

116

Sodium and sulfur release and recapture during black liquor burning  

SciTech Connect (OSTI)

The objective of this study was to provide data on sulfur and sodium volatilization during black liquor burning, and on SO2 capture by solid sodium carbonate and sodium chloride. This data was interpreted and modeled into rate equations suitable for use in computational models for recovery boilers.

Frederick, W.J.; Iisa, K.; Wag, K.; Reis, V.V.; Boonsongsup, L.; Forssen, M.; Hupa, M.

1995-08-01T23:59:59.000Z

117

Corrosion performance of advanced structural materials in sodium.  

SciTech Connect (OSTI)

This report gives a description of the activities in design, fabrication, construction, and assembling of a pumped sodium loop for the sodium compatibility studies on advanced structural materials. The work is the Argonne National Laboratory (ANL) portion of the effort on the work project entitled, 'Sodium Compatibility of Advanced Fast Reactor Materials,' and is a part of Advanced Materials Development within the Reactor Campaign. The objective of this project is to develop information on sodium corrosion compatibility of advanced materials being considered for sodium reactor applications. This report gives the status of the sodium pumped loop at Argonne National Laboratory, the specimen details, and the technical approach to evaluate the sodium compatibility of advanced structural alloys. This report is a deliverable from ANL in FY2010 (M2GAN10SF050302) under the work package G-AN10SF0503 'Sodium Compatibility of Advanced Fast Reactor Materials.' Two reports were issued in 2009 (Natesan and Meimei Li 2009, Natesan et al. 2009) which examined the thermodynamic and kinetic factors involved in the purity of liquid sodium coolant for sodium reactor applications as well as the design specifications for the ANL pumped loop for testing advanced structural materials. Available information was presented on solubility of several metallic and nonmetallic elements along with a discussion of the possible mechanisms for the accumulation of impurities in sodium. That report concluded that the solubility of many metals in sodium is low (<1 part per million) in the temperature range of interest in sodium reactors and such trace amounts would not impact the mechanical integrity of structural materials and components. The earlier report also analyzed the solubility and transport mechanisms of nonmetallic elements such as oxygen, nitrogen, carbon, and hydrogen in laboratory sodium loops and in reactor systems such as Experimental Breeder Reactor-II, Fast Flux Test Facility, and Clinch River Breeder Reactor. Among the nonmetallic elements discussed, oxygen is deemed controllable and its concentration in sodium can be maintained in sodium for long reactor life by using cold-trap method. It was concluded that among the cold-trap and getter-trap methods, the use of cold trap is sufficient to achieve oxygen concentration of the order of 1 part per million. Under these oxygen conditions in sodium, the corrosion performance of structural materials such as austenitic stainless steels and ferritic steels will be acceptable at a maximum core outlet sodium temperature of {approx}550 C. In the current sodium compatibility studies, the oxygen concentration in sodium will be controlled and maintained at {approx}1 ppm by controlling the cold trap temperature. The oxygen concentration in sodium in the forced convection sodium loop will be controlled and monitored by maintaining the cold trap temperature in the range of 120-150 C, which would result in oxygen concentration in the range of 1-2 ppm. Uniaxial tensile specimens are being exposed to flowing sodium and will be retrieved and analyzed for corrosion and post-exposure tensile properties. Advanced materials for sodium exposure include austenitic alloy HT-UPS and ferritic-martensitic steels modified 9Cr-1Mo and NF616. Among the nonmetallic elements in sodium, carbon was assessed to have the most influence on structural materials since carbon, as an impurity, is not amenable to control and maintenance by any of the simple purification methods. The dynamic equilibrium value for carbon in sodium systems is dependent on several factors, details of which were discussed in the earlier report. The current sodium compatibility studies will examine the role of carbon concentration in sodium on the carburization-decarburization of advanced structural materials at temperatures up to 650 C. Carbon will be added to the sodium by exposure of carbon-filled iron tubes, which over time will enable carbon to diffuse through iron and dissolve into sodium. The method enables addition of dissolved carbon (without carb

Natesan, K.; Momozaki, Y.; Li, M.; Rink, D.L. (Nuclear Engineering Division)

2012-05-16T23:59:59.000Z

118

Lighting Inventory Lighting Theatre and Drama  

E-Print Network [OSTI]

Lighting Inventory Lighting Theatre and Drama Description Totals R.Halls Wells- Metz Light ERS ETC SourceFour 25 25 50 degree ERS Strand Lighting 64 14 24 12 14 36 degree ERS ETC Source Four 15 15 36 degree ERS Strand Lighting 124 60 58 2 4 26 degree ERS ETC SourceFour 2 2 26 degree ERS Strand

Indiana University

119

Cast Stone Formulation At Higher Sodium Concentrations  

SciTech Connect (OSTI)

A low temperature waste form known as Cast Stone is being considered to provide supplemental Low Activity Waste (LAW) immobilization capacity for the Hanford site. Formulation of Cast Stone at high sodium concentrations is of interest since a significant reduction in the necessary volume of Cast Stone and subsequent disposal costs could be achieved if an acceptable waste form can be produced with a high sodium molarity salt solution combined with a high water to premix (or dry blend) ratio. The objectives of this study were to evaluate the factors involved with increasing the sodium concentration in Cast Stone, including production and performance properties and the retention and release of specific components of interest. Three factors were identified for the experimental matrix: the concentration of sodium in the simulated salt solution, the water to premix ratio, and the blast furnace slag portion of the premix. The salt solution simulants used in this study were formulated to represent the overall average waste composition. The cement, blast furnace slag, and fly ash were sourced from a supplier in the Hanford area in order to be representative. The test mixes were prepared in the laboratory and fresh properties were measured. Fresh density increased with increasing sodium molarity and with decreasing water to premix ratio, as expected given the individual densities of these components. Rheology measurements showed that all of the test mixes produced very fluid slurries. The fresh density and rheology data are of potential value in designing a future Cast Stone production facility. Standing water and density gradient testing showed that settling is not of particular concern for the high sodium compositions studied. Heat of hydration measurements may provide some insight into the reactions that occur within the test mixes, which may in turn be related to the properties and performance of the waste form. These measurements showed that increased sodium concentration in the salt solution reduced the time to peak heat flow, and reducing the amount of slag in the premix increased the time to peak heat flow. These observations may help to describe some of the cured properties of the samples, in particular the differences in compressive strength observed after 28 and 90 days of curing. Samples were cured for at least 28 days at ambient temperature in the laboratory prior to cured properties analyses. The low activity waste form for disposal at the Hanford Site is required to have a compressive strength of at least 500 psi. After 28 days of curing, several of the test mixes had mean compressive strengths that were below the 500 psi requirement. Higher sodium concentrations and higher water to premix ratios led to reduced compressive strength. Higher fly ash concentrations decreased the compressive strength after 28 days of curing. This may be explained in that the cementitious phases matured more quickly in the mixes with higher concentrations of slag, as evidenced by the data for the time to peak heat generation. All of the test mixes exhibited higher mean compressive strengths after 90 days of curing, with only one composition having a mean compressive strength of less than 500 psi. Leachability indices were determined for the test mixes for contaminants of interest. The leaching performance of the mixes evaluated in this study was not particularly sensitive to the factors used in the experimental design. This may be beneficial in demonstrating that the performance of the waste form is robust with respect to changes in the mix composition. The results of this study demonstrate the potential to achieve significantly higher waste loadings in Cast Stone and other low temperature, cementitious waste forms. Additional work is needed to elucidate the hydration mechanisms occurring in Cast Stone formulated with highly concentrated salt solutions since these reactions are responsible for determining the performance of the cured waste form. The thermal analyses completed in this study provide some preliminary insight, although the l

Fox, K. M.; Roberts, K. A.; Edwards, T. B.

2014-02-28T23:59:59.000Z

120

Cast Stone Formulation At Higher Sodium Concentrations  

SciTech Connect (OSTI)

A low temperature waste form known as Cast Stone is being considered to provide supplemental Low Activity Waste (LAW) immobilization capacity for the Hanford site. Formulation of Cast Stone at high sodium concentrations is of interest since a significant reduction in the necessary volume of Cast Stone and subsequent disposal costs could be achieved if an acceptable waste form can be produced with a high sodium molarity salt solution combined with a high water to premix (or dry blend) ratio. The objectives of this study were to evaluate the factors involved with increasing the sodium concentration in Cast Stone, including production and performance properties and the retention and release of specific components of interest. Three factors were identified for the experimental matrix: the concentration of sodium in the simulated salt solution, the water to premix ratio, and the blast furnace slag portion of the premix. The salt solution simulants used in this study were formulated to represent the overall average waste composition. The cement, blast furnace slag, and fly ash were sourced from a supplier in the Hanford area in order to be representative. The test mixes were prepared in the laboratory and fresh properties were measured. Fresh density increased with increasing sodium molarity and with decreasing water to premix ratio, as expected given the individual densities of these components. Rheology measurements showed that all of the test mixes produced very fluid slurries. The fresh density and rheology data are of potential value in designing a future Cast Stone production facility. Standing water and density gradient testing showed that settling is not of particular concern for the high sodium compositions studied. Heat of hydration measurements may provide some insight into the reactions that occur within the test mixes, which may in turn be related to the properties and performance of the waste form. These measurements showed that increased sodium concentration in the salt solution reduced the time to peak heat flow, and reducing the amount of slag in the premix increased the time to peak heat flow. These observations may help to describe some of the cured properties of the samples, in particular the differences in compressive strength observed after 28 and 90 days of curing. Samples were cured for at least 28 days at ambient temperature in the laboratory prior to cured properties analyses. The low activity waste form for disposal at the Hanford Site is required to have a compressive strength of at least 500 psi. After 28 days of curing, several of the test mixes had mean compressive strengths that were below the 500 psi requirement. Higher sodium concentrations and higher water to premix ratios led to reduced compressive strength. Higher fly ash concentrations decreased the compressive strength after 28 days of curing. This may be explained in that the cementitious phases matured more quickly in the mixes with higher concentrations of slag, as evidenced by the data for the time to peak heat generation. All of the test mixes exhibited higher mean compressive strengths after 90 days of curing, with only one composition having a mean compressive strength of less than 500 psi. Leach indices were determined for the test mixes for contaminants of interest. The leaching performance of the mixes evaluated in this study was not particularly sensitive to the factors used in the experimental design. This may be beneficial in demonstrating that the performance of the waste form is robust with respect to changes in the mix composition. The results of this study demonstrate the potential to achieve significantly higher waste loadings in Cast Stone and other low temperature, cementitious waste forms. Additional work is needed to elucidate the hydration mechanisms occurring in Cast Stone formulated with highly concentrated salt solutions since these reactions are responsible for determining the performance of the cured waste form. The thermal analyses completed in this study provide some preliminary insight, although the limited

Fox, K. M.; Roberts, K. A.; Edwards, T. B.

2013-09-17T23:59:59.000Z

Note: This page contains sample records for the topic "low-pressure sodium lighting" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Cast Stone Formulation At Higher Sodium Concentrations  

SciTech Connect (OSTI)

A low temperature waste form known as Cast Stone is being considered to provide supplemental Low Activity Waste (LAW) immobilization capacity for the Hanford site. Formulation of Cast Stone at high sodium concentrations is of interest since a significant reduction in the necessary volume of Cast Stone and subsequent disposal costs could be achieved if an acceptable waste form can be produced with a high sodium molarity salt solution combined with a high water to premix (or dry blend) ratio. The objectives of this study were to evaluate the factors involved with increasing the sodium concentration in Cast Stone, including production and performance properties and the retention and release of specific components of interest. Three factors were identified for the experimental matrix: the concentration of sodium in the simulated salt solution, the water to premix ratio, and the blast furnace slag portion of the premix. The salt solution simulants used in this study were formulated to represent the overall average waste composition. The cement, blast furnace slag, and fly ash were sourced from a supplier in the Hanford area in order to be representative. The test mixes were prepared in the laboratory and fresh properties were measured. Fresh density increased with increasing sodium molarity and with decreasing water to premix ratio, as expected given the individual densities of these components. Rheology measurements showed that all of the test mixes produced very fluid slurries. The fresh density and rheology data are of potential value in designing a future Cast Stone production facility. Standing water and density gradient testing showed that settling is not of particular concern for the high sodium compositions studied. Heat of hydration measurements may provide some insight into the reactions that occur within the test mixes, which may in turn be related to the properties and performance of the waste form. These measurements showed that increased sodium concentration in the salt solution reduced the time to peak heat flow, and reducing the amount of slag in the premix increased the time to peak heat flow. These observations may help to describe some of the cured properties of the samples, in particular the differences in compressive strength observed after 28 and 90 days of curing. Samples were cured for at least 28 days at ambient temperature in the laboratory prior to cured properties analyses. The low activity waste form for disposal at the Hanford Site is required to have a compressive strength of at least 500 psi. After 28 days of curing, several of the test mixes had mean compressive strengths that were below the 500 psi requirement. Higher sodium concentrations and higher water to premix ratios led to reduced compressive strength. Higher fly ash concentrations decreased the compressive strength after 28 days of curing. This may be explained in that the cementitious phases matured more quickly in the mixes with higher concentrations of slag, as evidenced by the data for the time to peak heat generation. All of the test mixes exhibited higher mean compressive strengths after 90 days of curing, with only one composition having a mean compressive strength of less than 500 psi. Leach indices were determined for the test mixes for contaminants of interest. The leaching performance of the mixes evaluated in this study was not particularly sensitive to the factors used in the experimental design. This may be beneficial in demonstrating that the performance of the waste form is robust with respect to changes in the mix composition. The results of this study demonstrate the potential to achieve significantly higher waste loadings in Cast Stone and other low temperature, cementitious waste forms. Additional work is needed to elucidate the hydration mechanisms occurring in Cast Stone formulated with highly concentrated salt solutions since these reactions are responsible for determining the performance of the cured waste form. The thermal analyses completed in this study provide some preliminary insight, although the limited

Fox, K. M.; Edwards, T. A.; Roberts, K. B.

2013-10-02T23:59:59.000Z

122

Acid/Base Recovery From Sodium Sulfate  

E-Print Network [OSTI]

escalating In price due to the Imbalance In market demand. Chlorine and caustic are produced together by the electrolysis 01 sodium chloride brine solutions. Every ECU (electrochemical unit) 01 chlorine resu~s In the production 01 one ECU 01 caustic soda... cell also produces an acid product that is contaminated with unreacted sullate. The voltage 01 a three compartment is higher, however, and the process system Is more complex. Process System Current density and efficiency determines the amount 01...

Niksa, M. J.

123

Light Source  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: VegetationEquipment Surfaces and Interfaces Sample6, 2011 LawrenceEfeedstocks and the climateLife a Light

124

Light' Darkness  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: VegetationEquipment Surfaces and Interfaces Sample6, 2011 LawrenceEfeedstocks and the climateLifeLight to

125

Residential Lighting  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administration the1 -the Mid-Infrared atEffectquestionnairesU.S. EnergyEnergy EfficiencyLighting

126

Light Water Reactor Sustainability  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

3 Light Water Reactor Sustainability Program ACCOMPLISHMENTS REPORT 2013 Accomplishments Report | Light Water Reactor Sustainability 2 T he mission of the Light Water Reactor...

127

Light Water Reactor Sustainability  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

4 Light Water Reactor Sustainability ACCOMPLISHMENTS REPORT 2014 Accomplishments Report | Light Water Reactor Sustainability 2 T he mission of the Light Water Reactor...

128

Recent Sodium Technology Development for the Decommissioning of the Rapsodie and Superphenix Reactors and the Management of Sodium Wastes  

SciTech Connect (OSTI)

The Commissariat a l'Energie Atomique (CEA) has recently developed and/or conducted experiments on several processes in support of the decommissioning of two French liquid-metal fast reactors (LMFRs), Rapsodie and Superphenix, as well as on the treatment of CEA sodium wastes. CEA has demonstrated that it is possible to define appropriate and efficient processes to meet the different situations encountered in decommissioning LMFRs. Mechanical techniques derived from standard technologies have been successfully applied to fast reactor decommissioning to complete primary vessel draining from sodium. In addition, specific chemical processes have been developed to deal safely with metallic sodium reactivity. Sodium-contaminated equipment has been successfully cleaned by reacting sodium with water mist in an atmosphere with carbon dioxide to form inert sodium carbonate. Bulk sodium has been successfully converted into aqueous caustic soda by injection of liquid-metallic sodium into sodium hydroxide solution. Several processes were also defined to deal with specific sodium wastes. In all cases the principle is based on a sodium/water chemical reaction where the released hydrogen and heat are controlled. With the development of a wide variety of processes, all steps in the decommissioning of LMFRs are assumed to be now properly mastered.

Rodriguez, G.; Gastaldi, O.; Baque, F. [Commissariat a l'Energie Atomique Cadarache (France)

2005-04-15T23:59:59.000Z

129

Report on sodium compatibility of advanced structural materials.  

SciTech Connect (OSTI)

This report provides an update on the evaluation of sodium compatibility of advanced structural materials. The report is a deliverable (level 3) in FY11 (M3A11AN04030403), under the Work Package A-11AN040304, 'Sodium Compatibility of Advanced Structural Materials' performed by Argonne National Laboratory (ANL), as part of Advanced Structural Materials Program for the Advanced Reactor Concepts. This work package supports the advanced structural materials development by providing corrosion and tensile data from the standpoint of sodium compatibility of advanced structural alloys. The scope of work involves exposure of advanced structural alloys such as G92, mod.9Cr-1Mo (G91) ferritic-martensitic steels and HT-UPS austenitic stainless steels to a flowing sodium environment with controlled impurity concentrations. The exposed specimens are analyzed for their corrosion performance, microstructural changes, and tensile behavior. Previous reports examined the thermodynamic and kinetic factors involved in the purity of liquid sodium coolant for sodium reactor applications as well as the design, fabrication, and construction of a forced convection sodium loop for sodium compatibility studies of advanced materials. This report presents the results on corrosion performance, microstructure, and tensile properties of advanced ferritic-martensitic and austenitic alloys exposed to liquid sodium at 550 C for up to 2700 h and at 650 C for up to 5064 h in the forced convection sodium loop. The oxygen content of sodium was controlled by the cold-trapping method to achieve {approx}1 wppm oxygen level. Four alloys were examined, G92 in the normalized and tempered condition (H1 G92), G92 in the cold-rolled condition (H2 G92), G91 in the normalized and tempered condition, and hot-rolled HT-UPS. G91 was included as a reference to compare with advanced alloy, G92. It was found that all four alloys showed weight loss after sodium exposures at 550 and 650 C. The weight loss of the four alloys was comparable after sodium exposures at 550 C; the weight loss of ferritic-martensitic steels, G92 and G91 is more significant than that of austenitic stainless steel, HT-UPS after sodium exposures at 650 C. Sodium exposures up to 2700 h at 550 C had no significant influence on tensile properties, while sodium exposures up to 5064 h at 650 C dramatically lowered the tensile strengths of the four alloys. The ultimate tensile strength of H1 G92, H2 G92, and G91 ferritic-martensitic steels was reduced to as much as nearly half of its initial value after sodium exposures at 650 C. Though the uniform elongation was recovered to some extent, these three ferritic-martensitic steels showed considerable strain softening after sodium exposures. The yield stress of HT-UPS austenitic stainless steel increased, the ultimate tensile strength decreased, and the total elongation was reduced after sodium exposures at 650 C. The dynamic strain aging effect observed in the as-received HT-UPS specimens became less pronounced after sodium exposures at 650 C. Microstructural characterization of sodium-exposed specimens showed no appreciable surface deterioration or grain structure changes under an optical microscope, except for the H2 G92 steel, in which the martensite structure transformed to large grain ferrite after sodium exposures at 650 C. TEM observations of the sodium-exposed H2 G92 steel showed significant recrystallization after sodium exposure for 2700 h at 550 C, and transformation of martensite to ferrite and high density of precipitates in nearly dislocation-free matrix after sodium exposures at 650 C. Further microstructural analysis and evaluation of decarburization/carburization behavior is needed to understand the dramatic changes in the tensile strengths of advanced ferritic-martensitic and austenitic steels after sodium exposures at 650 C.

Li, M.; Natesan, K.; Momozaki, Y.; Rink, D.L.; Soppet, W.K.; Listwan, J.T. (Nuclear Engineering Division)

2012-07-09T23:59:59.000Z

130

Factors contributing to the breakdown of sodium beta-alumina  

SciTech Connect (OSTI)

Clarification of the breakdown process occurring during charge transfer in sodium beta alumina solid electrolytes was derived from: (1) studying the effects of molten sodium contact at 350/sup 0/C on single crystal sodium beta alumina and polycrystalline sodium beta alumina; (2) determination of critical current density by monitoring acoustic emissions accompanying crack growth in sodium/sodium beta alumina/sodium cells subjected to linear current ramping at 1 mA cm/sup -2/ sec/sup -1/; (3) failure analysis conducted on cycled electrolytes, some from commercial sodium/sulfur cells, which had been subjected to up to 703 Ahr cm/sup -2/ of charge transfer. Gray coloration developing in beta aluminas in contact with molten sodium was found to be a consequence of formation, through reduction by sodium, of oxygen vacancies charge compensated by electrons. Electronic conductivity of the electrolyte increases as a result. No second phase formation was detected. Colored electrolytes from sodium/sulfur cells show evidence of a newly recognized degradation mechanism in which fracture occurs when sodium is reduced and deposited internally under pressure as metal in regions where an electronic conductivity gradient exists. Heating colored beta aluminas in air produces reoxidation and bleaching. Kinetics and other properties of the coloration and bleaching processes were determined. Critical current density was found to bear an inverse relation to average electrolyte grain size. Evidence was found in the cycled electrolytes for a slow crack growth mechanism and a progressive mode of degradation advancing from the sulfur electrode interface. Implications of the findings for the construction and operation of sodium/sulfur battery systems are discussed.

Buechele, A.C.

1982-05-01T23:59:59.000Z

131

Sustainable Office Lighting Options  

E-Print Network [OSTI]

Sustainable Office Lighting Options Task Lighting: Task lighting is a localized method of lighting a workspace so that additional, unnecessary lighting is eliminated, decreasing energy usage and costs. Illumination levels in the targeted work areas are higher with task lighting than with the ambient levels

Massachusetts at Amherst, University of

132

SWAAM-LT: The long-term, sodium/water reaction analysis method computer code  

SciTech Connect (OSTI)

The SWAAM-LT Code, developed for analysis of long-term effects of sodium/water reactions, is discussed. The theoretical formulation of the code is described, including the introduction of system matrices for ease of computer programming as a general system code. Also, some typical results of the code predictions for available large scale tests are presented. Test data for the steam generator design with the cover-gas feature and without the cover-gas feature are available and analyzed. The capabilities and limitations of the code are then discussed in light of the comparison between the code prediction and the test data.

Shin, Y.W.; Chung, H.H.; Wiedermann, A.H. [Argonne National Lab., IL (United States); Tanabe, H. [Power Reactor and Nuclear Fuel Development Corp., Tokai, Ibaraki (Japan)

1993-01-01T23:59:59.000Z

133

High-Compression-Ratio; Atkinson-Cycle Engine Using Low-Pressure Direct Injection and Pneumatic-Electronic Valve Actuation Enabled by Ionization Current and Foward-Backward Mass Air Flow Sensor Feedback  

SciTech Connect (OSTI)

This report describes the work completed over a two and one half year effort sponsored by the US Department of Energy. The goal was to demonstrate the technology needed to produce a highly efficient engine enabled by several technologies which were to be developed in the course of the work. The technologies included: (1) A low-pressure direct injection system; (2) A mass air flow sensor which would measure the net airflow into the engine on a per cycle basis; (3) A feedback control system enabled by measuring ionization current signals from the spark plug gap; and (4) An infinitely variable cam actuation system based on a pneumatic-hydraulic valve actuation These developments were supplemented by the use of advanced large eddy simulations as well as evaluations of fuel air mixing using the KIVA and WAVE models. The simulations were accompanied by experimental verification when possible. In this effort a solid base has been established for continued development of the advanced engine concepts originally proposed. Due to problems with the valve actuation system a complete demonstration of the engine concept originally proposed was not possible. Some of the highlights that were accomplished during this effort are: (1) A forward-backward mass air flow sensor has been developed and a patent application for the device has been submitted. We are optimistic that this technology will have a particular application in variable valve timing direct injection systems for IC engines. (2) The biggest effort on this project has involved the development of the pneumatic-hydraulic valve actuation system. This system was originally purchased from Cargine, a Swedish supplier and is in the development stage. To date we have not been able to use the actuators to control the exhaust valves, although the actuators have been successfully employed to control the intake valves. The reason for this is the additional complication associated with variable back pressure on the exhaust valves when they are opened. As a result of this effort, we have devised a new design and have filed for a patent on a method of control which is believed to overcome this problem. The engine we have been working with originally had a single camshaft which controlled both the intake and exhaust valves. Single cycle lift and timing control was demonstrated with this system. (3) Large eddy simulations and KIVA based simulations were used in conjunction with flow visualizations in an optical engine to study fuel air mixing. During this effort we have devised a metric for quantifying fuel distribution and it is described in several of our papers. (4) A control system has been developed to enable us to test the benefits of the various technologies. This system used is based on Opal-RT hardware and is being used in a current DOE sponsored program.

Harold Schock; Farhad Jaberi; Ahmed Naguib; Guoming Zhu; David Hung

2007-12-31T23:59:59.000Z

134

Sodium fast reactor safety and licensing research plan. Volume II.  

SciTech Connect (OSTI)

Expert panels comprised of subject matter experts identified at the U.S. National Laboratories (SNL, ANL, INL, ORNL, LBL, and BNL), universities (University of Wisconsin and Ohio State University), international agencies (IRSN, CEA, JAEA, KAERI, and JRC-IE) and private consultation companies (Radiation Effects Consulting) were assembled to perform a gap analysis for sodium fast reactor licensing. Expert-opinion elicitation was performed to qualitatively assess the current state of sodium fast reactor technologies. Five independent gap analyses were performed resulting in the following topical reports: (1) Accident Initiators and Sequences (i.e., Initiators/Sequences Technology Gap Analysis), (2) Sodium Technology Phenomena (i.e., Advanced Burner Reactor Sodium Technology Gap Analysis), (3) Fuels and Materials (i.e., Sodium Fast Reactor Fuels and Materials: Research Needs), (4) Source Term Characterization (i.e., Advanced Sodium Fast Reactor Accident Source Terms: Research Needs), and (5) Computer Codes and Models (i.e., Sodium Fast Reactor Gaps Analysis of Computer Codes and Models for Accident Analysis and Reactor Safety). Volume II of the Sodium Research Plan consolidates the five gap analysis reports produced by each expert panel, wherein the importance of the identified phenomena and necessities of further experimental research and code development were addressed. The findings from these five reports comprised the basis for the analysis in Sodium Fast Reactor Research Plan Volume I.

Ludewig, H. (Brokhaven National Laboratory, Upton, NY); Powers, D. A.; Hewson, John C.; LaChance, Jeffrey L.; Wright, A. (Argonne National Laboratory, Argonne, IL); Phillips, J.; Zeyen, R. (Institute for Energy Petten, Saint-Paul-lez-Durance, France); Clement, B. (IRSN/DPAM.SEMIC Bt 702, Saint-Paul-lez-Durance, France); Garner, Frank (Radiation Effects Consulting, Richland, WA); Walters, Leon (Advanced Reactor Concepts, Los Alamos, NM); Wright, Steve; Ott, Larry J. (Oak Ridge National Laboratory, Oak Ridge, TN); Suo-Anttila, Ahti Jorma; Denning, Richard (Ohio State University, Columbus, OH); Ohshima, Hiroyuki (Japan Atomic Energy Agency, Ibaraki, Japan); Ohno, S. (Japan Atomic Energy Agency, Ibaraki, Japan); Miyhara, S. (Japan Atomic Energy Agency, Ibaraki, Japan); Yacout, Abdellatif (Argonne National Laboratory, Argonne, IL); Farmer, M. (Argonne National Laboratory, Argonne, IL); Wade, D. (Argonne National Laboratory, Argonne, IL); Grandy, C. (Argonne National Laboratory, Argonne, IL); Schmidt, R.; Cahalen, J. (Argonne National Laboratory, Argonne, IL); Olivier, Tara Jean; Budnitz, R. (Lawrence Berkeley National Laboratory, Berkeley, CA); Tobita, Yoshiharu (Japan Atomic Energy Agency, Ibaraki, Japan); Serre, Frederic (Centre d'%C3%94etudes nucl%C3%94eaires de Cadarache, Cea, France); Natesan, Ken (Argonne National Laboratory, Argonne, IL); Carbajo, Juan J. (Oak Ridge National Laboratory, Oak Ridge, TN); Jeong, Hae-Yong (Korea Atomic Energy Research Institute, Daejeon, Korea); Wigeland, Roald (Idaho National Laboratory, Idaho Falls, ID); Corradini, Michael (University of Wisconsin-Madison, Madison, WI); Thomas, Justin (Argonne National Laboratory, Argonne, IL); Wei, Tom (Argonne National Laboratory, Argonne, IL); Sofu, Tanju (Argonne National Laboratory, Argonne, IL); Flanagan, George F. (Oak Ridge National Laboratory, Oak Ridge, TN); Bari, R. (Brokhaven National Laboratory, Upton, NY); Porter D. (Idaho National Laboratory, Idaho Falls, ID); Lambert, J. (Argonne National Laboratory, Argonne, IL); Hayes, S. (Idaho National Laboratory, Idaho Falls, ID); Sackett, J. (Idaho National Laboratory, Idaho Falls, ID); Denman, Matthew R.

2012-05-01T23:59:59.000Z

135

Sodium cobalt bronze batteries and a method for making same  

DOE Patents [OSTI]

A solid state secondary battery utilizing a low cost, environmentally sound, sodium cobalt bronze electrode. A method is provided for producing same.

Doeff, Marca M. (Hayward, CA); Ma, Yanping (Berkeley, CA); Visco, Steven J. (Berkeley, CA); DeJonghe, Lutgard (Lafayette, CA)

1999-01-01T23:59:59.000Z

136

Sodium cobalt bronze batteries and a method for making same  

DOE Patents [OSTI]

A solid state secondary battery utilizing a low cost, environmentally sound, sodium cobalt bronze electrode is described. A method is provided for producing same. 11 figs.

Doeff, M.M.; Ma, Y.; Visco, S.J.; DeJonghe, L.

1999-06-29T23:59:59.000Z

137

Idaho Site Obtains Patent for Nuclear Reactor Sodium Cleanup...  

Office of Environmental Management (EM)

Idaho Site Obtains Patent for Nuclear Reactor Sodium Cleanup Treatment March 28, 2013 - 12:00pm Addthis CWI engineers Jeff Jones, David Tolman, right, and Kirk Dooley...

138

Efficacy of soluble sodium tripolyphosphate amendments for the...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

of soluble sodium tripolyphosphate amendments for the in-situ immobilisation of uranium."Environmental Chemistry 4:293-300. Authors: DM Wellman EM Pierce MM Valenta...

139

Sodium dichromate expedited response action assessment  

SciTech Connect (OSTI)

The US Environmental Protection Agency (EPA) and Washington Department of Ecology (Ecology) recommended that the US Department of Energy (DOE) perform an expedited response action (ERA) for the Sodium Dichromate Barrel Disposal Landfill. The ERA lead regulatory agency is Ecology and EPA is the support agency. The ERA was categorized as non-time-critical, which required preparation of an engineering evaluation and cost analysis (EE/CA). The EE/CA was included in the ERA proposal. The EE/CA is a rapid, focused evaluation of available technologies using specific screening factors to assess feasibility, appropriateness, and cost. The ERA goal is to reduce the potential for any contaminant migration from the landfill to the soil column, groundwater, and Columbia River. Since the Sodium Dichromate Barrel Disposal Landfill is the only waste site within the operable unit, the removal action may be the final remediation of the 100-IU-4 Operable Unit. This ERA process started in March 1992. The ERA proposal went through a parallel review process with Westinghouse Hanford Company (WHC), DOE Richland Operations (RL), EPA, Ecology, and a 30-day public comment period. Ecology and EPA issued an Action Agreement Memorandum in March 1993 (Appendix A). The memorandum directed excavation of all anomalies and disposal of the collected materials at the Hanford Site Central Landfill. Primary field activities were completed by the end of April 1993. Final waste disposal of a minor quantity of hazardous waste was completed in July 1993.

Not Available

1993-09-01T23:59:59.000Z

140

Thermal analysis for fuel handling system for sodium cooled reactor considering minor actinide-bearing metal fuel.  

SciTech Connect (OSTI)

The Advanced Burner Reactor (ABR) is one of the components of the Global Nuclear Energy Partnership (GNEP) used to close the fuel cycle. ABR is a sodium-cooled fast reactor that is used to consume transuranic elements resulting from the reprocessing of light water reactor spent nuclear fuel. ABR-1000 [1000 MW(thermal)] is a fast reactor concept created at Argonne National Laboratory to be used as a reference concept for various future trade-offs. ABR-1000 meets the GNEP goals although it uses what is considered base sodium fast reactor technology for its systems and components. One of the considerations of any fast reactor plant concept is the ability to perform fuel-handling operations with new and spent fast reactor fuel. The transmutation fuel proposed as the ABR fuel has a very little experience base, and thus, this paper investigates a fuel-handling concept and potential issues of handling fast reactor fuel containing minor actinides. In this study, two thermal analyses supporting a conceptual design study on the ABR-1000 fuel-handling system were carried out. One analysis investigated passive dry spent fuel storage, and the other analysis investigated a fresh fuel shipping cask. Passive dry storage can be made suitable for the ABR-1000 spent fuel storage with sodium-bonded metal fuel. The thermal analysis shows that spent fast reactor fuel with a decay heat of 2 kW or less can be stored passively in a helium atmosphere. The 2-kW value seems to be a reasonable and practical level, and a combination of reasonably-sized in-sodium storage followed by passive dry storage could be a candidate for spent fuel storage for the next-generation sodium-cooled reactor with sodium-bonded metal fuel. Requirements for the shipping casks for minor actinide-bearing fuel with a high decay heat level are also discussed in this paper. The shipping cask for fresh sodium-cooled-reactor fuel should be a dry type to reduce the reaction between residual moisture on fresh fuel and the sodium coolant. The cladding temperature requirement is maintained below the creep temperature limit to avoid any damage before core installation. The thermal analysis shows that a helium gas-filled cask can accommodate ABR-1000 fresh minor actinide-bearing fuel with 700-W decay heat. The above analysis results revealed the overall requirement for minor actinide-bearing metal fuel handling. The information is thought to be helpful in the design of the ABR-1000 and future sodium-cooled-reactor fuel-handling system.

Chikazawa, Y.; Grandy, C.; Nuclear Engineering Division

2009-03-01T23:59:59.000Z

Note: This page contains sample records for the topic "low-pressure sodium lighting" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Lighting Options for Homes.  

SciTech Connect (OSTI)

This report covers many aspects of various lighting options for homes. Types of light sources described include natural light, artificial light, incandescent lamps, fluorescent lamps, and high intensity discharge lamps. A light source selection guide gives the physical characteristics of these, design considerations, and common applications. Color, strategies for efficient lighting, and types of lighting are discussed. There is one section giving tips for various situations in specific rooms. Rooms and types of fixtures are shown on a matrix with watts saved by using the recommended type lighting for that room and room location. A major emphasis of this report is saving energy by utilizing the most suitable, recommended lighting option. (BN)

Baker, W.S.

1991-04-01T23:59:59.000Z

142

Mobile lighting apparatus  

DOE Patents [OSTI]

A mobile lighting apparatus includes a portable frame such as a moveable trailer or skid having a light tower thereon. The light tower is moveable from a stowed position to a deployed position. A hydrogen-powered fuel cell is located on the portable frame to provide electrical power to an array of the energy efficient lights located on the light tower.

Roe, George Michael; Klebanoff, Leonard Elliott; Rea, Gerald W; Drake, Robert A; Johnson, Terry A; Wingert, Steven John; Damberger, Thomas A; Skradski, Thomas J; Radley, Christopher James; Oros, James M; Schuttinger, Paul G; Grupp, David J; Prey, Stephen Carl

2013-05-14T23:59:59.000Z

143

RESEARCH Open Access Half-molar sodium lactate infusion improves  

E-Print Network [OSTI]

RESEARCH Open Access Half-molar sodium lactate infusion improves cardiac performance in acute heart for the myocardium at rest and during stress. We tested the effects of half-molar sodium lactate infusion on cardiac by 1 ml/kg/h continuous infusion for 24 hours. The control group received only a 3 ml/kg bolus

Paris-Sud XI, Université de

144

Mercury exosphere I. Global circulation model of its sodium component  

E-Print Network [OSTI]

Mercury exosphere I. Global circulation model of its sodium component Francois Leblanc a,*, R 2010 Accepted 27 April 2010 Available online 5 May 2010 Keywords: Mercury, Atmosphere Aeronomy a b s t r a c t Our understanding of Mercury's sodium exosphere has improved considerably in the last 5

Johnson, Robert E.

145

Neutronic Assessment of Transmutation Target Compositions in Heterogeneous Sodium Fast Reactor Geometries  

SciTech Connect (OSTI)

The sodium fast reactor is under consideration for consuming the transuranic waste in the spent nuclear fuel generated by light water reactors. This work is concerned with specialized target assemblies for an oxide-fueled sodium fast reactor that are designed exclusively for burning the americium and higher mass actinide component of light water reactor spent nuclear fuel (SNF). The associated gamma and neutron radioactivity, as well as thermal heat, associated with decay of these actinides may significantly complicate fuel handling and fabrication of recycled fast reactor fuel. The objective of using targets is to isolate in a smaller number of assemblies these concentrations of higher actinides, thus reducing the volume of fuel having more rigorous handling requirements or a more complicated fabrication process. This is in contrast to homogeneous recycle where all recycled actinides are distributed among all fuel assemblies. Several heterogeneous core geometries were evaluated to determine the fewest target assemblies required to burn these actinides without violating a set of established fuel performance criteria. The DIF3D/REBUS code from Argonne National Laboratory was used to perform the core physics and accompanying fuel cycle calculations in support of this work. Using the REBUS code, each core design was evaluated at the equilibrium cycle condition.

Samuel E. Bays; Rodolfo M. Ferrer; Michael A. Pope; Benoit Forget; Mehdi Asgari

2008-02-01T23:59:59.000Z

146

Calibration of the On-Line Aerosol Monitor (OLAM) with ammonium chloride and sodium chloride aerosols  

SciTech Connect (OSTI)

The On-Line Aerosol Monitor (OLAM) is a light attenuation device designed and built at the Idaho National Engineering Laboratory (INEL) by EG&G Idaho. Its purpose is to provide an on-line indication of aerosol concentration in the PHEBUS-FP tests. It does this by measuring the attenuation of a light beam across a tube through which an aerosol is flowing. The OLAM does not inherently give an absolute response and must be calibrated. A calibration has been performed at Sandia National Laboratories` (SNL) Sandia Aerosol Research Laboratory (SARL) and the results are described here. Ammonium chloride and sodium chloride calibration aerosols are used for the calibration and the data for the sodium chloride aerosol is well described by a model presented in this report. Detectable instrument response is seen over a range of 0.1 cm{sup 3} of particulate material per m{sup 3} of gas to 10 cm{sup 3} of particulate material per m{sup 3} of gas.

Brockmann, J.E.; Lucero, D.A.; Romero, T. [Sandia National Labs., Albuquerque, NM (United States); Pentecost, G. [Idaho National Engineering Lab., Idaho Falls, ID (United States)

1993-12-01T23:59:59.000Z

147

Low temperature sodium-beta battery  

DOE Patents [OSTI]

A battery that will operate at ambient temperature or lower includes an enclosure, a current collector within the enclosure, an anode that will operate at ambient temperature or lower within the enclosure, a cathode that will operate at ambient temperature or lower within the enclosure, and a separator and electrolyte within the enclosure between the anode and the cathode. The anode is a sodium eutectic anode that will operate at ambient temperature or lower and is made of a material that is in a liquid state at ambient temperature or lower. The cathode is a low melting ion liquid cathode that will operate at ambient temperature or lower and is made of a material that is in a liquid state at ambient temperature or lower.

Farmer, Joseph C

2013-11-19T23:59:59.000Z

148

EK101 Engineering Light Smart Lighting  

E-Print Network [OSTI]

EK101 Engineering Light Smart Lighting Homework for 9/10 1. Make an estimate (using if the patent is granted.) 3. What is a lumen? A lux? How are the two related? How would you use a lux meter, (Lux, Lumens/m2) Luminous Flux: Perceivable light power from a source, (Lumens) Use the lux meter

Bifano, Thomas

149

Environmental and health aspects of lighting: Mercury  

SciTech Connect (OSTI)

Most discharge lamps, including fluorescent lamps, metal halide lamps, and high pressure sodium lamps, contain Mercury, a toxic chemical. Lighting professionals need to be able to respond to questions about the direct hazards of Mercury from accidentally breaking lamps, and the potential environmental hazards of lamp operation and disposal. We calculated the exposures that could occur from an accidental breakage of lamps. Acute poisoning appears almost impossible. Under some circumstances a sealed environment, such as a space station, could be contaminated enough to make it unhealthy for long-term occupation. Mercury becomes a potential environmental hazard after it becomes methylated. Mercury is methylated in aquatic environments, where it may accumulate in fish, eventually rendering them toxic to people and other animals. Lighting causes Mercury to enter the environment directly from lamp disposal, and indirectly from power plant emissions. The environmental tradeoffs between incandescent and discharge lamps depend upon the amounts released by these two sources, their local concentrations, and their probabilities of being methylated. Indirect environmental effects of lighting also include the release of other heavy metals (Cadmium, Lead and Arsenic), and other air pollutants and carbon dioxide that are emitted by fossil fuel power plants. For a given light output, the level of power plant emissions depends upon the efficacy of the light source, and is thus much larger for incandescent lamps than for fluorescent or discharge lamps. As disposal and control technologies change the relative direct and indirect emissions from discharge and incandescent lamps will change.

Clear, R.; Berman, S.

1993-07-01T23:59:59.000Z

150

Production of sodium-22 from proton irradiated aluminum  

DOE Patents [OSTI]

A process for selective separation of sodium-22 from a proton irradiated minum target including dissolving a proton irradiated aluminum target in hydrochloric acid to form a first solution including aluminum ions and sodium ions, separating a portion of the aluminum ions from the first solution by crystallization of an aluminum salt, contacting the remaining first solution with an anion exchange resin whereby ions selected from the group consisting of iron and copper are selectively absorbed by the anion exchange resin while aluminum ions and sodium ions remain in solution, contacting the solution with an cation exchange resin whereby aluminum ions and sodium ions are adsorbed by the cation exchange resin, and, contacting the cation exchange resin with an acid solution capable of selectively separating the adsorbed sodium ions from the cation exchange resin while aluminum ions remain adsorbed on the cation exchange resin is disclosed.

Taylor, Wayne A. (Los Alamos, NM); Heaton, Richard C. (Los Alamos, NM); Jamriska, David J. (Los Alamos, NM)

1996-01-01T23:59:59.000Z

151

Theoretical Adiabatic Temperature and Chemical Composition of Sodium Combustion Flame  

SciTech Connect (OSTI)

Sodium fire safety analysis requires fundamental combustion properties, e.g., heat of combustion, flame temperature, and composition. We developed the GENESYS code for a theoretical investigation of sodium combustion flame.Our principle conclusions on sodium combustion under atmospheric air conditions are (a) the maximum theoretical flame temperature is 1950 K, and it is not affected by the presence of moisture; the uppermost limiting factor is the chemical instability of the condensed sodium-oxide products under high temperature; (b) the main combustion product is liquid Na{sub 2}O in dry air condition and liquid Na{sub 2}O with gaseous NaOH in moist air; and (c) the chemical equilibrium prediction of the residual gaseous reactants in the flame is indispensable for sodium combustion modeling.

Okano, Yasushi; Yamaguchi, Akira [O-arai Engineering Center (Japan)

2003-12-15T23:59:59.000Z

152

Calcium and sodium bentonite for hydraulic containment applications  

SciTech Connect (OSTI)

The hydraulic conductivity of calcium and sodium bentonites was investigated for sand-bentonite mixtures, a thin bentonite layer simulating a geosynthetic clay liner (GCL), and bentonite-cement mixtures simulating backfill for a vertical cutoff wall. The permeant liquids were tap water and distilled water containing 0.25 M calcium chloride. In general, the hydraulic performance of calcium bentonite was not significantly better than the performance of sodium bentonite for either the clay-amended sand or the GCL application, and was substantially worse than the performance of sodium bentonite in the bentonite-cement mixture. A drained angle of internal friction of 21{degree} was measured for calcium bentonite, compared to 10{degree} for sodium bentonite. Except for a larger drained shear strength, no advantage of calcium bentonite over sodium bentonite could be identified from the results of this study.

Gleason, M.H. [GeoSyntec Consultants, Columbia, MD (United States); Daniel, D.E. [Univ. of Illinois, Urbana, IL (United States). Dept. of Civil Engineering; Eykholt, G.R. [Univ. of Wisconsin, Madison, WI (United States). Dept. of Civil Engineering

1997-05-01T23:59:59.000Z

153

Specific light in sculpture  

E-Print Network [OSTI]

Specific light is defined as light from artificial or altered natural sources. The use and manipulation of light in three dimensional sculptural work is discussed in an historic and contemporary context. The author's work ...

Powell, John William

1989-01-01T23:59:59.000Z

154

Decommissioning of Experimental Breeder Reactor - II Complex, Post Sodium Draining  

SciTech Connect (OSTI)

The Experimental Breeder Reactor - II (EBR-II) was shutdown in September 1994 as mandated by the United States Department of Energy. This sodium-cooled reactor had been in service since 1964. The bulk sodium was drained from the primary and secondary systems and processed. Residual sodium remaining in the systems after draining was converted into sodium bicarbonate using humid carbon dioxide. This technique was tested at Argonne National Laboratory in Illinois under controlled conditions, then demonstrated on a larger scale by treating residual sodium within the EBR-II secondary cooling system, followed by the primary tank. This process, terminated in 2002, was used to place a layer of sodium bicarbonate over all exposed surfaces of sodium. Treatment of the remaining EBR-II sodium is governed by the Resource Conservation and Recovery Act (RCRA). The Idaho Department of Environmental Quality issued a RCRA Operating Permit in 2002, mandating that all hazardous materials be removed from EBR-II within a 10 year period, with the ability to extend the permit and treatment period for another 10 years. A preliminary plan has been formulated to remove the remaining sodium and NaK from the primary and secondary systems using moist carbon dioxide, steam and nitrogen, and a water flush. The moist carbon dioxide treatment was resumed in May 2004. As of August 2005, approximately 60% of the residual sodium within the EBR-II primary tank had been treated. This process will continue through the end of 2005, when it is forecast that the process will become increasingly ineffective. At that time, subsequent treatment processes will be planned and initiated. It should be noted that the processes and anticipated costs associated with these processes are preliminary. Detailed engineering has not been performed, and approval for these methods has not been obtained from the regulator or the sponsors.

J. A. (Bart) Michelbacher; S. Paul Henslee; Collin J. Knight; Steven R. sherman

2005-09-01T23:59:59.000Z

155

On the white light luminescence induced by irradiation of sodium nitrate single crystals by 1064 nm laser light  

E-Print Network [OSTI]

NO3). NaNO3 is a major component of high level nuclear wastes in underground storage tanks associated with US plutonium production during the cold war. Analyzing such wastes safely and accurately requires), jtd@wsu.edu (J.T. Dickinson). 1 Present Address: Hellenic Institute of Metrology, Industrial Area

Dickinson, J. Thomas

156

E-Print Network 3.0 - acetate sodium lactate Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

sodium-high lactate infusion'. Of course, it is easy to demonstrate that high lactate infusion... . Also, sodium-lactate infusion in humans ... Source: Ecole Polytechnique, Centre...

157

E-Print Network 3.0 - advanced fast sodium Sample Search Results  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

sodium in the PFBR). The same initiating events occurring in both thermal and fast reactors could produce... specifications of demonstration fast reactors.* Thermal Sodium void...

158

Experimental investigations on sodium plugging in narrow flow channels.  

SciTech Connect (OSTI)

A series of experiments was performed to investigate the potential for plugging of narrow flow channels of sodium by impurities (e.g., oxides). In the first phase of the experiments, clean sodium was circulated through the test sections simulating flow channels in a compact diffusion-bonded heat exchanger such as a printed circuit heat exchanger. The primary objective was to see if small channels whose cross sections are semicircles of 2, 4, and 6 mm in diameter are usable in liquid sodium applications where sodium purity is carefully controlled. It was concluded that the 2-mm channels, the smallest of the three, could be used in clean sodium systems at temperatures even as low as 100 to 110 C without plugging. In the second phase, sodium oxide was added to the loop, and the oxygen concentration in the liquid sodium was controlled by means of varying the cold-trap temperature. Intentional plugging was induced by creating a cold spot in the test sections, and the subsequent plugging behavior was observed. It was found that plugging in the 2-mm test section was initiated by lowering the cold spot temperature below the cold-trap temperature by 10 to 30 C. Unplugging of the plugged channels was accomplished by heating the affected test section.

Momozaki, Y.; Cho, D. H.; Sienicki, J. J.; Moisseytsev, A.; Nuclear Engineering Division

2010-08-01T23:59:59.000Z

159

Applicability of RELAP5-3D for Thermal-Hydraulic Analyses of a Sodium-Cooled Actinide Burner Test Reactor  

SciTech Connect (OSTI)

The Actinide Burner Test Reactor (ABTR) is envisioned as a sodium-cooled, fast reactor that will burn the actinides generated in light water reactors to reduce nuclear waste and ease proliferation concerns. The RELAP5-3D computer code is being considered as the thermal-hydraulic system code to support the development of the ABTR. An evaluation was performed to determine the applicability of RELAP5-3D for the analysis of a sodium-cooled fast reactor. The applicability evaluation consisted of several steps, including identifying the important transients and phenomena expected in the ABTR, identifying the models and correlations that affect the code’s calculation of the important phenomena, and evaluating the applicability of the important models and correlations for calculating the important phenomena expected in the ABTR. The applicability evaluation identified code improvements and additional models needed to simulate the ABTR. The accuracy of the calculated thermodynamic and transport properties for sodium was also evaluated.

C. B. Davis

2006-07-01T23:59:59.000Z

160

Risk Management for Sodium Fast Reactors.  

SciTech Connect (OSTI)

Accident management is an important component to maintaining risk at acceptable levels for all complex systems, such as nuclear power plants. With the introduction of self - correcting, or inherently safe, reactor designs the focus has shifted from management by operators to allowing the syste m's design to manage the accident. While inherently and passively safe designs are laudable, extreme boundary conditions can interfere with the design attributes which facilitate inherent safety , thus resulting in unanticipated and undesirable end states. This report examines an inherently safe and small sodium fast reactor experiencing a beyond design basis seismic event with the intend of exploring two issues : (1) can human intervention either improve or worsen the potential end states and (2) can a Bayes ian Network be constructed to infer the state of the reactor to inform (1). ACKNOWLEDGEMENTS The author s would like to acknowledge the U.S. Department of E nergy's Office of Nuclear Energy for funding this research through Work Package SR - 14SN100303 under the Advanced Reactor Concepts program. The authors also acknowledge the PRA teams at A rgonne N ational L aborator y , O ak R idge N ational L aborator y , and I daho N ational L aborator y for their continue d contributions to the advanced reactor PRA mission area.

Denman, Matthew R; Groth, Katrina; Cardoni, Jeffrey N; Wheeler, Timothy A.

2015-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "low-pressure sodium lighting" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Sodium Bearing Waste Processing Alternatives Analysis  

SciTech Connect (OSTI)

A multidisciplinary team gathered to develop a BBWI recommendation to DOE-ID on the processing alternatives for the sodium bearing waste in the INTEC Tank Farm. Numerous alternatives were analyzed using a rigorous, systematic approach. The data gathered were evaluated through internal and external peer reviews for consistency and validity. Three alternatives were identified to be top performers: Risk-based Calcination, MACT to WIPP Calcination and Cesium Ion Exchange. A dual-path through early Conceptual design is recommended for MACT to WIPP Calcination and Cesium Ion Exchange since Risk-based Calcination does not require design. If calcination alternatives are not considered based on giving Type of Processing criteria significantly greater weight, the CsIX/TRUEX alternative follows CsIX in ranking. However, since CsIX/TRUEX shares common uncertainties with CsIX, reasonable backups, which follow in ranking, are the TRUEX and UNEX alternatives. Key uncertainties must be evaluated by the decision-makers to choose one final alternative. Those key uncertainties and a path forward for the technology roadmapping of these alternatives is provided.

Murphy, James Anthony; Palmer, Brent J; Perry, Keith Joseph

2003-12-01T23:59:59.000Z

162

Lighting and Daylight Harvesting  

E-Print Network [OSTI]

exposing us to the latest products and technologies. Daylight Harvesting A system of controlling the direction and the quantity of light both natural and artificial within a given space. This implies: Control of fenestration in terms of size..., transmission and direction. Control of reflected light within a space. Control of electric light in terms of delivery and amount Daylight harvesting systems are typically designed to maintain a minimum recommended light level. This light level...

Bos, J.

2011-01-01T23:59:59.000Z

163

Loop simulation capability for sodium-cooled systems  

E-Print Network [OSTI]

A one-dimensional loop simulation capability has been implemented in the thermal-hydraulic analysis code, THERMIT-4E. This code had been used to simulate and investigate flow in test sections of experimental sodium loops ...

Adekugbe, Oluwole A.

1984-01-01T23:59:59.000Z

164

aged sodium borophosphate: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

ultraviolet flux will produce a similar variation in the column of neutral sodium for a fixed mass flux and density. However, if the cold gas is in pressure equilibrium with a hot...

165

aqueous sodium chloride: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

made with either sodium chloride or potassium chloride. The addition of 75 or 150 porn N02 did not lower plate counts (P&0. 05... Kayfus, Timothy Jon 2012-06-07 58 Systematic...

166

Reactor protection system design alternatives for sodium fast reactors  

E-Print Network [OSTI]

Historically, unprotected transients have been viewed as design basis events that can significantly challenge sodium-cooled fast reactors. The perceived potential consequences of a severe unprotected transient in a ...

DeWitte, Jacob D. (Jacob Dominic)

2011-01-01T23:59:59.000Z

167

Probabilistic transient analysis of fuel choices for sodium fast reactors  

E-Print Network [OSTI]

This thesis presents the implications of using a risk-informed licensing framework to inform the design of Sodium Fast Reactors. NUREG-1860, more commonly known as the Technology Neutral Framework (TNF), is a risk-informed ...

Denman, Matthew R

2011-01-01T23:59:59.000Z

168

SLAM: a sodium-limestone concrete ablation model  

SciTech Connect (OSTI)

SLAM is a three-region model, containing a pool (sodium and reaction debris) region, a dry (boundary layer and dehydrated concrete) region, and a wet (hydrated concrete) region. The model includes a solution to the mass, momentum, and energy equations in each region. A chemical kinetics model is included to provide heat sources due to chemical reactions between the sodium and the concrete. Both isolated model as well as integrated whole code evaluations have been made with good results. The chemical kinetics and water migration models were evaluated separately, with good results. Several small and large-scale sodium limestone concrete experiments were simulated with reasonable agreement between SLAM and the experimental results. The SLAM code was applied to investigate the effects of mixing, pool temperature, pool depth and fluidization. All these phenomena were found to be of significance in the predicted response of the sodium concrete interaction. Pool fluidization is predicted to be the most important variable in large scale interactions.

Suo-Anttila, A.J.

1983-12-01T23:59:59.000Z

169

Sodium Ion Insertion in Hollow Carbon Nanowires for Battery Applicatio...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

B Schwenzer, J Xiao, Z Nie, LV Saraf, Z Yang, and J Liu.2012."Sodium Ion Insertion in Hollow Carbon Nanowires for Battery Applications."Nano Letters 12(7):37833787....

170

The Salt or Sodium Chloride Content of Feeds  

E-Print Network [OSTI]

of Sodium Chloride.--In order to test the recovery of added salt, several molasses feeds were selected, weighed out, and varying amounts of salt added, in the form of a N/10 solution of sodium chloride. The salt was added hy a different person from... ............................... . . Preliminary ~vork on laboratory methocls ........ . . ............................... Laboratory method adopted.. ............................. Tests of the laboratory niethod. ................... Application of the methold to feed mixtures...

Fraps, G. S. (George Stronach); Lomanitz, S. (Sebastian)

1920-01-01T23:59:59.000Z

171

Advanced sodium fast reactor accident source terms : research needs.  

SciTech Connect (OSTI)

An expert opinion elicitation has been used to evaluate phenomena that could affect releases of radionuclides during accidents at sodium-cooled fast reactors. The intent was to identify research needed to develop a mechanistic model of radionuclide release for licensing and risk assessment purposes. Experts from the USA, France, the European Union, and Japan identified phenomena that could affect the release of radionuclides under hypothesized accident conditions. They qualitatively evaluated the importance of these phenomena and the need for additional experimental research. The experts identified seven phenomena that are of high importance and have a high need for additional experimental research: High temperature release of radionuclides from fuel during an energetic eventEnergetic interactions between molten reactor fuel and sodium coolant and associated transfer of radionuclides from the fuel to the coolantEntrainment of fuel and sodium bond material during the depressurization of a fuel rod with breached claddingRates of radionuclide leaching from fuel by liquid sodiumSurface enrichment of sodium pools by dissolved and suspended radionuclidesThermal decomposition of sodium iodide in the containment atmosphereReactions of iodine species in the containment to form volatile organic iodides. Other issues of high importance were identified that might merit further research as development of the mechanistic model of radionuclide release progressed.

Powers, Dana Auburn; Clement, Bernard [IRSN/DPAM.SEMIC Bt 702, Saint-Paul-lez-Durance, France; Denning, Richard [Ohio State University, Columbus, OH; Ohno, Shuji [Japan Atomic Energy Agency, Ibaraki, Japan; Zeyen, Roland [Institute for Energy Petten, Saint-Paul-lez-Durance, France

2010-09-01T23:59:59.000Z

172

Classification : Original Article VOLTAGE-GATED SODIUM CHANNELS POTENTIATE THE INVASIVE  

E-Print Network [OSTI]

- gated sodium channels in non-small-cell lung cancer cell lines. Functional voltage-gated sodium channels cancerous cell lines H23, H460 and Calu-1 possess functional sodium channels while normal and weakly metastatic cell lines do not. While all the cell lines expressed mRNA for numerous sodium channel isoforms

Boyer, Edmond

173

Method of and apparatus for removing silicon from a high temperature sodium coolant  

DOE Patents [OSTI]

A method of and system for removing silicon from a high temperature liquid sodium coolant system for a nuclear reactor. The sodium is cooled to a temperature below the silicon saturation temperature and retained at such reduced temperature while inducing high turbulence into the sodium flow for promoting precipitation of silicon compounds and ultimate separation of silicon compound particles from the liquid sodium.

Yunker, Wayne H. (Richland, WA); Christiansen, David W. (Kennewick, WA)

1987-01-01T23:59:59.000Z

174

Evaluation of lithium as a toxicant and the modifying effect of sodium  

SciTech Connect (OSTI)

Routine compliance tests conducted for a groundwater treatment facility at the Y-12 Plant on the Department of Energy`s (DOE) Oak Ridge Reservation (ORR), TN, showed that the effluent was acutely toxic to Ceriodaphnia dubia and fathead minnow (Pimephales promelas) larvae. An evaluation of suspected contaminants revealed that increased toxicity coincided with increased concentrations of lithium. Lithium is a light, strong metal that is used in DOE operations, including fusion weapons and fission reactors. Little has been published about lithium toxicity. Toxicity tests were conducted with fathead minnows and C. dubia using lithium chloride and lithium tetraborate. Dilute mineral water (DMW) or the receiving stream water (East Fork Poplar Creek) was used as the dilution water in the toxicity evaluation. A concentration of 1 mg Li/L in DMW reduced the survival of both test species; 0.5 mg Li/L in DMW reduced C. dubia reproduction and minnow growth. Sodium appears to influence the toxicity of Li; the metal was six times more toxic in the low-sodium DMW than in stream water containing 30 mg Na/L. Tests with LiCl in combination with NaCl and NA{sub 2}SO{sub 4} demonstrated that the presence of sodium reduced the toxicity of Li to C. dubia. In laboratory tests with a snail (Elimia clavaeformis) common on the ORR, the feeding rate declined in 0.15 mg Li/L. Because Li has also been demonstrated to be toxic to several plant species, tests with LiCi were also conducted using buttercrunch lettuce (Lactuca saliva). The EC{sub 50} for seed growth after 8 d incubation was 37.5 mg Li/L. These findings are significant because of widespread industrial use and potential accumulation of Li in soils.

Kszos, L.A.; Stewart, A.J.; O`Reilly, S.E. [Oak Ridge National Lab., TN (United States)

1995-12-31T23:59:59.000Z

175

Experimental Development and Demonstration of Ultrasonic Measurement Diagnostics for Sodium Fast Reactor Thermal-hydraulics  

SciTech Connect (OSTI)

This research project will address some of the principal technology issues related to sodium-cooled fast reactors (SFR), primarily the development and demonstration of ultrasonic measurement diagnostics linked to effective thermal convective sensing under normatl and off-normal conditions. Sodium is well-suited as a heat transfer medium for the SFR. However, because it is chemically reactive and optically opaque, it presents engineering accessibility constraints relative to operations and maintenance (O&M) and in-service inspection (ISI) technologies that are currently used for light water reactors. Thus, there are limited sensing options for conducting thermohydraulic measurements under normal conditions and off-normal events (maintenance, unanticipated events). Acoustic methods, primarily ultrasonics, are a key measurement technology with applications in non-destructive testing, component imaging, thermometry, and velocimetry. THis project would have yielded a better quantitative and qualitative understanding of the thermohydraulic condition of solium under varied flow conditions. THe scope of work will evaluate and demonstrate ultrasonic technologies and define instrumentation options for the SFR.

Tokuhiro, Akira; Jones, Byron

2013-09-13T23:59:59.000Z

176

Kyler Nelson Light Timer  

E-Print Network [OSTI]

designated by the user, the Arduino board will dim the light to save energy. The user designates the time instance, the light is dimmed using pulse width modulation (PWM) in the Arduino's pin number 11

Kachroo, Pushkin

177

AIRPORT LIGHTING Session Highlights  

E-Print Network [OSTI]

AIRPORT LIGHTING Session Highlights In May 2002, the Airport Technical Assistance Program, also known as AirTAP, sponsored three airport-lighting training sessions at different locations in Minnesota information on airport lighting and navigational aid equipment selection, funding, maintenance, and operation

Minnesota, University of

178

Advanced Demand Responsive Lighting  

E-Print Network [OSTI]

Advanced Demand Responsive Lighting Host: Francis Rubinstein Demand Response Research Center demand responsive lighting systems ­ Importance of dimming ­ New wireless controls technologies · Advanced Demand Responsive Lighting (commenced March 2007) #12;Objectives · Provide up-to-date information

179

Light emitting device comprising phosphorescent materials for white light generation  

DOE Patents [OSTI]

The present invention relates to phosphors for energy downconversion of high energy light to generate a broadband light spectrum, which emit light of different emission wavelengths.

Thompson, Mark E.; Dapkus, P. Daniel

2014-07-22T23:59:59.000Z

180

Light Duty Combustion Research: Advanced Light-Duty Combustion...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Combustion Research: Advanced Light-Duty Combustion Experiments Light Duty Combustion Research: Advanced Light-Duty Combustion Experiments 2009 DOE Hydrogen Program and Vehicle...

Note: This page contains sample records for the topic "low-pressure sodium lighting" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Energy savings with solid-state ballasted high-pressure sodium lamps  

SciTech Connect (OSTI)

The performance of three types of solid-state ballasts used to operate high-pressure sodium lamps is discussed. Each type of solid-state ballast has been designed to operate an HPS lamp of a different wattage (150, 200, and 400 watts). The performance of these ballasts compared to standard core-coil ballasts operating the same HPS lamps shows that system efficiency improves as much as 17%. The solid-state ballasted HPS system also demonstrates excellent regulation with respect to input voltage and output power. These new ballasts can dim the HPS lamps and reduce flicker from more than 60% to less than 3%. Refitting street lighting with these new HPS systims provides an attractive return on initial capital investment.

Verderber, R.R.; Morse, O.

1981-04-01T23:59:59.000Z

182

Photonic crystal light source  

DOE Patents [OSTI]

A light source is provided by a photonic crystal having an enhanced photonic density-of-states over a band of frequencies and wherein at least one of the dielectric materials of the photonic crystal has a complex dielectric constant, thereby producing enhanced light emission at the band of frequencies when the photonic crystal is heated. The dielectric material can be a metal, such as tungsten. The spectral properties of the light source can be easily tuned by modification of the photonic crystal structure and materials. The photonic crystal light source can be heated electrically or other heating means. The light source can further include additional photonic crystals that exhibit enhanced light emission at a different band of frequencies to provide for color mixing. The photonic crystal light source may have applications in optical telecommunications, information displays, energy conversion, sensors, and other optical applications.

Fleming, James G. (Albuquerque, NM); Lin, Shawn-Yu (Albuquerque, NM); Bur, James A. (Corrales, NM)

2004-07-27T23:59:59.000Z

183

Light extraction from organic light-emitting diodes for lighting applications by sand-blasting  

E-Print Network [OSTI]

Light extraction from organic light-emitting diodes for lighting applications by sand@ust.hk Abstract: Light extraction from organic light-emitting diodes (OLEDs) by scattering the light is one of the effective methods for large-area lighting applications. In this paper, we present a very simple and cost

184

SMART LIGHTING SYSTEMS ULTIMATE LIGHTING The Smart Lighting  

E-Print Network [OSTI]

Integration (Holistic Integrated Design) · Sensors as important as LEDs · Interconnected systems (human, building, grid) · Artistic Design Freedom · Lighting is Health, Entertainment, Information and Illumination Cost at any brightness · Chip level integrated electronics THE ERC RESEARCH COVERS THE ENTIRE SUPPLY

Linhardt, Robert J.

185

Energy Saving Melting and Revert Reduction Technology (Energy-SMARRT): Light Metals Permanent Mold Casting  

SciTech Connect (OSTI)

Current vehicles use mostly ferrous components for structural applications. It is possible to reduce the weight of the vehicle by substituting these parts with those made from light metals such as aluminum and magnesium. Many alloys and manufacturing processes can be used to produce these light metal components and casting is known to be most economical. One of the high integrity casting processes is permanent mold casting which is the focus of this research report. Many aluminum alloy castings used in automotive applications are produced by the sand casting process. Also, aluminum-silicon (Al-Si) alloys are the most widely used alloy systems for automotive applications. It is possible that by using high strength aluminum alloys based on an aluminum-copper (Al-Cu) system and permanent mold casting, the performance of these components can be enhanced significantly. This will also help to further reduce the weight. However, many technological obstacles need to be overcome before using these alloys in automotive applications in an economical way. There is very limited information in the open literature on gravity and low-pressure permanent mold casting of high strength aluminum alloys. This report summarizes the results and issues encountered during the casting trials of high strength aluminum alloy 206.0 (Al-Cu alloy) and moderate strength alloy 535.0 (Al-Mg alloy). Five engineering components were cast by gravity tilt-pour or low pressure permanent mold casting processes at CanmetMATERIALS (CMAT) and two production foundries. The results of the casting trials show that high integrity engineering components can be produced successfully from both alloys if specific processing parameters are used. It was shown that a combination of melt processing and mold temperature is necessary for the elimination of hot tears in both alloys.

Fasoyinu, Yemi [CanmetMATERIALS] [CanmetMATERIALS

2014-03-31T23:59:59.000Z

186

Arnold Schwarzenegger LIGHTING RESEARCH PROGRAM  

E-Print Network [OSTI]

Project Summaries ELEMENT 2: ADVANCE LIGHTING TECHNOLOGIES PROJECT 2.1 LIGHT EMITTING DIODE (LED light emitting diodes (LED) technology for general lighting applications by developing a task lamp

187

Numerical Methodology to Evaluate Fast Reactor Sodium Combustion  

SciTech Connect (OSTI)

In the present study, a numerical methodology for sodium combustion has been developed for the safety evaluation of a liquid-metal-cooled fast reactor. The methodology includes a fast-running zone model computer program for safety evaluation, a field model program for multidimensional thermal hydraulics, and a chemical reaction analysis program based on chemical equilibrium theory. Two recently performed experiments have been analyzed using the computer programs, and the numerical results are in good agreement with the experiments. Although sodium combustion is a complex phenomenon, use of these computer programs gives better understanding of the coupled thermal hydraulics and chemical reaction.

Yamaguchi, Akira; Takata, Takashi; Okano, Yasushi [Japan Nuclear Cycle Development Institute (Japan)

2001-12-15T23:59:59.000Z

188

The magnesium nutrition of cotton as influenced by sodium  

E-Print Network [OSTI]

1964 Major Subject. Plant Physic logy THE MAGNESIUM NUTRITION OF COTTON AS INFLUENCED BY SODIUM A Thesis By MERVYN M. THENABADU Approved as to style and content by: Chairman of Commi. e Nun Head of Department Member Mem, er Member Member... REVIEW OF LITERATURE (a) Sodium as a plant nutrient (b) I'he role of magnesium in plant nutrition MATERIALS AND METHODS RESUL:S DISCUSSION 13 21 24 (a) The effect of treatments on grcwth and reproduction (b) The effect of treatments on the ccr...

Thenabadu, Mervyn Wellesly

2012-06-07T23:59:59.000Z

189

Aluminum Zintl anion moieties within sodium aluminum clusters  

SciTech Connect (OSTI)

Through a synergetic combination of anion photoelectron spectroscopy and density functional theory based calculations, we have established that aluminum moieties within selected sodium-aluminum clusters are Zintl anions. Sodium–aluminum cluster anions, Na{sub m}Al{sub n}{sup ?}, were generated in a pulsed arc discharge source. After mass selection, their photoelectron spectra were measured by a magnetic bottle, electron energy analyzer. Calculations on a select sub-set of stoichiometries provided geometric structures and full charge analyses for both cluster anions and their neutral cluster counterparts, as well as photodetachment transition energies (stick spectra), and fragment molecular orbital based correlation diagrams.

Wang, Haopeng; Zhang, Xinxing; Ko, Yeon Jae; Grubisic, Andrej; Li, Xiang; Ganteför, Gerd; Bowen, Kit H., E-mail: AKandalam@wcupa.edu, E-mail: kiran@mcneese.edu, E-mail: kbowen@jhu.edu [Department of Chemistry, Johns Hopkins University, Baltimore, Maryland 21218 (United States); Schnöckel, Hansgeorg [Institute of Inorganic Chemistry, Karlsruhe Institute of Technology, 76128 Karlsruhe (Germany)] [Institute of Inorganic Chemistry, Karlsruhe Institute of Technology, 76128 Karlsruhe (Germany); Eichhorn, Bryan W. [Department of Chemistry, University of Maryland at College Park, College Park, Maryland 20742 (United States)] [Department of Chemistry, University of Maryland at College Park, College Park, Maryland 20742 (United States); Lee, Mal-Soon; Jena, P. [Department of Physics, Virginia Commonwealth University, Richmond, Virginia 23284 (United States)] [Department of Physics, Virginia Commonwealth University, Richmond, Virginia 23284 (United States); Kandalam, Anil K., E-mail: AKandalam@wcupa.edu, E-mail: kiran@mcneese.edu, E-mail: kbowen@jhu.edu [Department of Physics, West Chester University of Pennsylvania, West Chester, Pennsylvania 19383 (United States); Kiran, Boggavarapu, E-mail: AKandalam@wcupa.edu, E-mail: kiran@mcneese.edu, E-mail: kbowen@jhu.edu [Department of Chemistry, McNeese State University, Lake Charles, Louisiana 70609 (United States)] [Department of Chemistry, McNeese State University, Lake Charles, Louisiana 70609 (United States)

2014-02-07T23:59:59.000Z

190

New Light Sources for Tomorrow's Lighting Designs  

E-Print Network [OSTI]

, pioneered for headlam~for the automotive industry, has led to the development of halo en capsule lamps for general lighting. The original90-watt family PAR 38 lamps using tungsten halogen capsules produces the sa amount of useful light in the beam as a I... quartz PAR lamps with similar benefi . Each of these tungsten halogen capsule PAR wattages are av ilable in narrow spot, spot, and flood beam patterns. The most recent developments in the PAR halogen psule family include two entirely new lamp designs...

Krailo, D. A.

191

National Synchrotron Light Source  

ScienceCinema (OSTI)

A tour of Brookhaven's National Synchrotron Light Source (NSLS), hosted by Associate Laboratory Director for Light Sources, Stephen Dierker. The NSLS is one of the world's most widely used scientific research facilities, hosting more than 2,500 guest researchers each year. The NSLS provides intense beams of infrared, ultraviolet, and x-ray light for basic and applied research in physics, chemistry, medicine, geophysics, environmental, and materials sciences.

BNL

2009-09-01T23:59:59.000Z

192

LED Lighting Retrofit  

E-Print Network [OSTI]

? Municipal Street Lighting Consortium ? American Public Power Association (APPA) ? Demonstration in Energy Efficiency Development (DEED) ? Source of funding and database of completed LED roadway projects 6 Rules of the Road ESL-KT-11-11-57 CATEE 2011..., 2011 ? 9 Solar-Assisted LED Case Study LaQuinta Hotel, Cedar Park, Texas ? Utilizes 18 - ActiveLED Solar-Assisted Parking Lot Lights ? Utilizes ?power management? to extend battery life while handling light output ? Reduces load which reduces PV...

Shaw-Meadow, N.

2011-01-01T23:59:59.000Z

193

High efficiency incandescent lighting  

DOE Patents [OSTI]

Incandescent lighting structure. The structure includes a thermal emitter that can, but does not have to, include a first photonic crystal on its surface to tailor thermal emission coupled to, in a high-view-factor geometry, a second photonic filter selected to reflect infrared radiation back to the emitter while passing visible light. This structure is highly efficient as compared to standard incandescent light bulbs.

Bermel, Peter; Ilic, Ognjen; Chan, Walker R.; Musabeyoglu, Ahmet; Cukierman, Aviv Ruben; Harradon, Michael Robert; Celanovic, Ivan; Soljacic, Marin

2014-09-02T23:59:59.000Z

194

Ion Recognition Approach to Volume Reduction of Alkaline Tank Waste by Separation and Recycle of Sodium Hydroxide and Sodium Nitrate  

SciTech Connect (OSTI)

This research has focused on new liquid-liquid extraction chemistry applicable to separation of major sodium salts from alkaline tank waste. It was the overall goal to provide the scientific foundation upon which the feasibility of liquid-liquid extraction chemistry for bulk reduction of the volume of tank waste can be evaluated. Sodium hydroxide represented the initial test case and primary focus. It is a primary component of the waste1 and has the most value for recycle. A full explanation of the relevance of this research to USDOE Environmental Management needs will be given in the Relevance, Impact, and Technology Transfer section below. It should be noted that this effort was predicated on the need for sodium removal primarily from low-activity waste, whereas evolving needs have shifted attention to volume reduction of the high-activity waste. The results of the research to date apply to both applications, though treatment of high-activity wastes raises new questions that will be addressed in the renewal period. Toward understanding the extractive chemistry of sodium hydroxide and other sodium salts, it was the intent to identify candidate extractants and determine their applicable basic properties regarding selectivity, efficiency, speciation, and structure. A hierarchical strategy was to be employed in which the type of liquid-liquid-extraction system varied in sophistication from simple, single-component solvents to solvents containing designer host molecules. As an aid in directing this investigation toward addressing the fundamental questions having the most value, a conceptualization of an ideal process was advanced. Accordingly, achieving adequate selectivity for sodium hydroxide represented a primary goal, but this result is worthwhile for waste applications only if certain conditions are met.

Moyer, Bruce A.; Marchand, Alan P.; Bonnesen, Peter V.; Bryan, Jeffrey C.; Haverlock, Tamara J.

2002-03-30T23:59:59.000Z

195

Total Light Management  

Broader source: Energy.gov [DOE]

Presentation covers total light management, and is given at the Spring 2010 Federal Utility Partnership Working Group (FUPWG) meeting in Providence, Rhode Island.

196

Lighting Technology Panel  

Broader source: Energy.gov [DOE]

Presentation covers the Lighting Technology Panel for the Federal Utility Partnership Working Group (FUPWG) meeting, held on November 18-19, 2009. 

197

Comparing Light Bulbs  

Broader source: Energy.gov [DOE]

In this exercise, students will use a light to demonstrate the difference between being energy-efficient and energy-wasteful, and learn what energy efficiency means.

198

Solid-State Lighting  

Broader source: Energy.gov (indexed) [DOE]

research and design. Quality LED luminaires require program designed to successfully move solid-state lighting precise design of several components -LED arrays, electronic into the...

199

FATE OF INGESTED SODIUM BICARBONATE IN THE FOWL  

E-Print Network [OSTI]

. 100 calcium while rations 3 and4contained 3.85 p. 100 calcium. Sodium bicarbonate was added at a level. The duodenum was entered at the top of the loop and the electrode tip immersed its full length down the posterior side of the loop. The #12;mid-intestinal reading was taken with the incision at approximately

Paris-Sud XI, Université de

200

Electrochemical Recovery of Sodium Hydroxide from Alkaline Salt Solution  

SciTech Connect (OSTI)

A statistically designed set of tests determined the effects of current density, temperature, and the concentrations of nitrate/nitrite, hydroxide and aluminate on the recovery of sodium as sodium hydroxide (caustic) from solutions simulating those produced from the Savannah River Site (SRS) In-Tank Precipitation process. These tests included low nitrate and nitrite concentrations which would be produced by electrolytic nitrate/nitrite destruction. The tests used a two compartment electrochemical cell with a Nafion Type 324 ion-exchange membrane. Caustic was successfully recovered from the waste solutions. Evaluation of the testing results indicated that the transport of sodium across the membrane was not significantly affected by any of the varied parameters. The observed variance in the sodium flux is attributed to experimental errors and variations in the performance characteristics of individual pieces of the organic-based Nafion membrane.Additional testing is recommended to determine the maximum current density, to evaluate the chemical durability of the organic membrane as a function of current density and to compare the durability and performance characteristics of the organic-based Nafion membrane with that of other commercially available organic membranes and the inorganic class of membranes under development by Ceramatec and PNNL.

Hobbs, D.T. [Westinghouse Savannah River Company, AIKEN, SC (United States); Edwards, T.B.

1996-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "low-pressure sodium lighting" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Process for making boron nitride using sodium cyanide and boron  

DOE Patents [OSTI]

This a very simple process for making boron nitride by mixing sodium cyanide and boron phosphate and heating the mixture in an inert atmosphere until a reaction takes place. The product is a white powder of boron nitride that can be used in applications that require compounds that are stable at high temperatures and that exhibit high electrical resistance.

Bamberger, Carlos E. (Oak Ridge, TN)

1990-01-01T23:59:59.000Z

202

ORIGINAL RESEARCH Systematic family-wide analysis of sodium bicarbonate  

E-Print Network [OSTI]

ORIGINAL RESEARCH Systematic family-wide analysis of sodium bicarbonate cotransporter NBCn1/SLC4A7/NBCn1 pulled down syntrophin c2 and con- versely GST/syntrophin c2 pulled down NBCn1. Moreover normally moves Na+ and HCO3 Ã? into cells and protects intracel- lular pH (pHi) from falling below normal

Hall, Randy A

203

Laboratory-scale sodium-carbonate aggregate concrete interactions. [LMFBR  

SciTech Connect (OSTI)

A series of laboratory-scale experiments was made at 600/sup 0/C to identify the important heat-producing chemical reactions between sodium and carbonate aggregate concretes. Reactions between sodium and carbonate aggregate were found to be responsible for the bulk of heat production in sodium-concrete tests. Exothermic reactions were initiated at 580+-30/sup 0/C for limestone and dolostone aggregates as well as for hydrated limestone concrete, and at 540+-10/sup 0/C for dehydrated limestone concrete, but were ill-defined for dolostone concrete. Major reaction products included CaO, MgO, Na/sub 2/CO/sub 3/, Na/sub 2/O, NaOH, and elemental carbon. Sodium hydroxide, which forms when water is released from cement phases, causes slow erosion of the concrete with little heat production. The time-temperature profiles of these experiments have been modeled with a simplified version of the SLAM computer code, which has allowed derivation of chemical reaction rate coefficients.

Westrich, H.R.; Stockman, H.W.; Suo-Anttila, A.

1983-09-01T23:59:59.000Z

204

Method of Manufacturing Micro-Disperse Particles of Sodium Borohydride  

DOE Patents [OSTI]

A compact solid source of hydrogen gas, where the gas is generated by contacting water with micro-disperse particles of sodium borohydride in the presence of a catalyst, such as cobalt or ruthenium. The micro-disperse particles can have a substantially uniform diameter of 1-10 microns, and preferably about 3-5 microns. Ruthenium or cobalt catalytic nanoparticles can be incorporated in the micro-disperse particles of sodium borohydride, which allows a rapid and complete reaction to occur without the problems associated with caking and scaling of the surface by the reactant product sodium metaborate. A closed loop water management system can be used to recycle wastewater from a PEM fuel cell to supply water for reacting with the micro-disperse particles of sodium borohydride in a compact hydrogen gas generator. Capillary forces can wick water from a water reservoir into a packed bed of micro-disperse fuel particles, eliminating the need for using an active pump.

Kravitz, Stanley H. (Placitas, NM); Hecht, Andrew M. (Sandia Park, NM); Sylwester. Alan P. (Albuquerque, NM); Bell, Nelson S. (Albuquerque, NM)

2008-09-23T23:59:59.000Z

205

Method of generating hydrogen gas from sodium borohydride  

DOE Patents [OSTI]

A compact solid source of hydrogen gas, where the gas is generated by contacting water with micro-disperse particles of sodium borohydride in the presence of a catalyst, such as cobalt or ruthenium. The micro-disperse particles can have a substantially uniform diameter of 1-10 microns, and preferably about 3-5 microns. Ruthenium or cobalt catalytic nanoparticles can be incorporated in the micro-disperse particles of sodium borohydride, which allows a rapid and complete reaction to occur without the problems associated with caking and scaling of the surface by the reactant product sodium metaborate. A closed loop water management system can be used to recycle wastewater from a PEM fuel cell to supply water for reacting with the micro-disperse particles of sodium borohydride in a compact hydrogen gas generator. Capillary forces can wick water from a water reservoir into a packed bed of micro-disperse fuel particles, eliminating the need for using an active pump.

Kravitz, Stanley H. (Placitas, NM); Hecht, Andrew M. (Sandia Park, NM); Sylwester, Alan P. (Albuquerque, NM); Bell, Nelson S. (Albuquerque, NM)

2007-12-11T23:59:59.000Z

206

Immobilization of sodium nitrate waste with polymers: Topical report  

SciTech Connect (OSTI)

This report describes the development of solidification systems for sodium nitrate waste. Sodium nitrate waste was solidified in the polymers polyethylene, polyester-styrene (PES), and water-extendible polyester-styrene (WEP). Evaluations were made of the properties of waste forms containing various amounts of sodium nitrate by leaching immersion in water, measuring compressive strengths and by the EPA Extraction Procedure. Results of the leaching test are presented as cumulative fraction leached (CFL), incremental leaching rate, and average leaching indices (LI). For waste forms containing 30 to 70 wt% sodium nitrate, the CFL ranged from 9.0 x 10/sup -3/ to 7.3 x 10/sup -1/ and the LI from 11 to 7.8. After ninety days immersion in water, the compressive strengths ranged from 720 psi to 2550 psi. The nitrate releases from these samples using the EPA Extraction Procedure were below 500 ppM. The nitrate releases from PES waste forms were similar to those from polyethylene waste forms at the same waste loadings. The compressive yield strengths, measured after ninety-day immersion in water, ranged between 2070 and 7710 psi. In the case of WEP waste forms, only 30 wt% loaded samples passed the immersion test. 23 refs., 24 figs., 12 tabs.

Franz, E.M.; Heiser, J.H. III; Colombo, P.

1987-04-01T23:59:59.000Z

207

Compatibility Assessment of Advanced Stainless Steels in Sodium  

SciTech Connect (OSTI)

Type 316L stainless steel capsules containing commercially pure sodium and miniature tensile specimens of HT-UPS (austenitic, 14Cr-16Ni), NF-616 (ferritic/martensitic, 9Cr-2W-0.5Mo), or 316L (austenitic, 17Cr-10Ni-2Mo) stainless steel were exposed at 600 or 700 C for 100 and 400 h as a screening test for compatibility. Using weight change, tensile testing, and metallographic analysis, HT-UPS and 316L were found to be largely immune to changes resulting from sodium exposure, but NF-616 was found susceptible to substantial decarburization at 700 C. Subsequently, two thermal convection loops (TCLs) constructed of 316L and loaded with commercially pure sodium and miniature tensile specimens of HT-UPS and 316L were operated for 2000 h each one between 500 and 650 C, the other between 565 and 725 C at a flow rate of about 1.5 cm/s. Changes in specimen appearance, weight, and tensile properties were observed to be very minor in all cases, and there was no metallographic evidence of microstructure changes, composition gradients, or mass transfer resulting from prolonged exposure in a TCL. Thus, it appears that HT-UPS and 316L stainless steels are similarly compatible with commercially pure sodium under these exposure conditions.

Pawel, Steven J [ORNL

2012-01-01T23:59:59.000Z

208

OpenGL Lighting 13. OpenGL Lighting  

E-Print Network [OSTI]

OpenGL Lighting 13. OpenGL Lighting · Overview of Lighting in OpenGL In order for lighting to have an effect in OpenGL, two things are required: A light An object to be lit Lights can be set to any color determine how they reflect the light which hits them. The color(s) of an object is determined

McDowell, Perry

209

Chemistry of Petroleum Crude Oil Deposits: Sodium Naphthenates 2009 NHMFL Science Highlight for NSF  

E-Print Network [OSTI]

Chemistry of Petroleum Crude Oil Deposits: Sodium Naphthenates 2009 NHMFL Science Highlight for NSF-355. Chemistry of Petroleum Crude Oil Deposits: Sodium Naphthenates 2009 NHMFL Science Highlight for NSF DMR

Weston, Ken

210

apical sodium-chloride cotransporter: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

g magnesium chloride, 3.24 g magnesium sulfate bromide, 34 mg strontium chloride, 22 mg boric acid, 4 mg sodium silicate, 2.4 mg sodium fluoride, 1.6 mg Bae, Jin-Woo 302 The...

211

Light intensity compressor  

DOE Patents [OSTI]

In a system for recording images having vastly differing light intensities over the face of the image, a light intensity compressor is provided that utilizes the properties of twisted nematic liquid crystals to compress the image intensity. A photoconductor or photodiode material that is responsive to the wavelength of radiation being recorded is placed adjacent a layer of twisted nematic liquid crystal material. An electric potential applied to a pair of electrodes that are disposed outside of the liquid crystal/photoconductor arrangement to provide an electric field in the vicinity of the liquid crystal material. The electrodes are substantially transparent to the form of radiation being recorded. A pair of crossed polarizers are provided on opposite sides of the liquid crystal. The front polarizer linearly polarizes the light, while the back polarizer cooperates with the front polarizer and the liquid crystal material to compress the intensity of a viewed scene. Light incident upon the intensity compressor activates the photoconductor in proportion to the intensity of the light, thereby varying the field applied to the liquid crystal. The increased field causes the liquid crystal to have less of a twisting effect on the incident linearly polarized light, which will cause an increased percentage of the light to be absorbed by the back polarizer. The intensity of an image may be compressed by forming an image on the light intensity compressor.

Rushford, Michael C. (Livermore, CA)

1990-01-01T23:59:59.000Z

212

Splayed mirror light pipes  

SciTech Connect (OSTI)

An expression is given for the transmission of the rectangular-section mirror light pipe. The expression is used to model throughputs for simulated solar conditions over a calender year. It is found that the splaying of a mirror light pipe results in a significant increase in throughputs particularly in winter months. (author)

Swift, P.D. [School of Physical Sciences, Dublin City University, Dublin 9 (Ireland)

2010-02-15T23:59:59.000Z

213

Explosively pumped laser light  

DOE Patents [OSTI]

A single shot laser pumped by detonation of an explosive in a shell casing. The shock wave from detonation of the explosive causes a rare gas to luminesce. The high intensity light from the gas enters a lasing medium, which thereafter outputs a pulse of laser light to disable optical sensors and personnel.

Piltch, Martin S. (Los Alamos, NM); Michelotti, Roy A. (Los Alamos, NM)

1991-01-01T23:59:59.000Z

214

Reducing home lighting expenses  

SciTech Connect (OSTI)

Ways to reduce lighting expenses are summarized. These include: turning off lights when not in use; keeping fixtures and lamps clean; replacing lamps with more efficient types; using three-way bulbs; use of daylighting; buying fewer lamps and reducing lamp wattage; consider repainting rooms; replacing recessed fixtures with tracklighting; and using efficient lamps for outdoor use. (MCW)

Aimone, M.A.

1981-02-01T23:59:59.000Z

215

Method of and apparatus for removing silicon from a high temperature sodium coolant  

DOE Patents [OSTI]

This patent discloses a method of and system for removing silicon from a high temperature liquid sodium coolant system for a nuclear reactor. The sodium is cooled to a temperature below the silicon saturation temperature and retained at such reduced temperature while inducing high turbulence into the sodium flow for promoting precipitation of silicon compounds and ultimate separation of silicon compound particles from the liquid sodium.

Yunker, W.H.; Christiansen, D.W.

1983-11-25T23:59:59.000Z

216

Go No-Go Recommendation for Sodium Borohydride for On-Board Vehicular Hydrogen Storage  

Fuel Cell Technologies Publication and Product Library (EERE)

Independent review panel recommendation for go/no go decision on use of hydrolysis of sodium borohydride for hydrogen storage.

217

VIRTUAL LIGHT: DIGITALLY-GENERATED LIGHTING FOR VIDEO CONFERENCING APPLICATIONS  

E-Print Network [OSTI]

VIRTUAL LIGHT: DIGITALLY-GENERATED LIGHTING FOR VIDEO CONFERENCING APPLICATIONS Andrea Basso method to improve the lighting conditions of a real scene or video sequence. In particular we concentrate on modifying real light sources intensities and inserting virtual lights into a real scene viewed from a fixed

Fisher, Kathleen

218

Lighting affects appearance LightSource emits photons  

E-Print Network [OSTI]

1 Lighting affects appearance #12;2 LightSource emits photons Photons travel in a straight line). And then some reach the eye/camera. #12;3 Reflectance Model how objects reflect light. Model light sources Algorithms for computing Shading: computing intensities within polygons Determine what light strikes what

Jacobs, David

219

Ultracold Molecules from Ultracold Atoms: Interactions in Sodium and Lithium Gas  

E-Print Network [OSTI]

Ultracold Molecules from Ultracold Atoms: Interactions in Sodium and Lithium Gas by Caleb from Ultracold Atoms: Interactions in Sodium and Lithium Gas by Caleb A Christensen Submitted of Philosophy Abstract The thesis presents results from experiments in which ultracold Sodium-6 and Lithium-23

220

Synthesis of highly ordered mesoporous silica materials using sodium silicate and amphiphilic block copolymers  

E-Print Network [OSTI]

Synthesis of highly ordered mesoporous silica materials using sodium silicate and amphiphilic block) structures, using sodium silicate as the silica source and amphiphilic block copolymers as the structure of mesoporous silica material using nonionic surfac- tant and sodium silicate in the pH range 3­10.5. However

Kim, Ji Man

Note: This page contains sample records for the topic "low-pressure sodium lighting" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Exhaust Aftertreatment and Low Pressure Loop EGR Applied to an...  

Broader source: Energy.gov (indexed) [DOE]

Loop EGR Applied to an Off-Highway Engine Project Director- Kirby Baumgard John Deere Power Systems DOE Project Officer- Steve Cooke Subcontract with Michigan Tech August 21...

222

Low pressure EGR system having full range capability  

DOE Patents [OSTI]

An exhaust treatment system for an engine is disclosed and may have an air induction circuit, an exhaust circuit, and an exhaust recirculation circuit. The air induction circuit may be configured to direct air into the engine. The exhaust circuit may be configured to direct exhaust from the engine and include a turbine driven by the exhaust, a particulate filter disposed in series with and downstream of the turbine, and a catalytic device disposed in series with and downstream of the particulate filter. The exhaust recirculation circuit may be configured to selectively redirect at least some of the exhaust from between the particulate filter and the catalytic device to the air induction circuit. The catalytic device is selected to create backpressure within the exhaust circuit sufficient to ensure that, under normal engine operating conditions above low idle, exhaust can flow into the air induction circuit without throttling of the air.

Easley, Jr., William Lanier; Milam, David Michael; Roozenboom, Stephan Donald; Bond, Michael Steven; Kapic, Amir

2009-09-22T23:59:59.000Z

223

THE ABSORPTION OF HYDROGEN ON LOW PRESSURE HYDRIDE MATERIALS  

SciTech Connect (OSTI)

For this study, hydrogen getter materials (Zircaloy-4 and pure zirconium) that have a high affinity for hydrogen (and low overpressure) have been investigated to determine the hydrogen equilibrium pressure on Zircaloy-4 and pure zirconium. These materials, as with most getter materials, offered significant challenges to overcome given the low hydrogen equilibrium pressure for the temperature range of interest. Hydrogen-zirconium data exists for pure zirconium at 500 C and the corresponding hydrogen overpressure is roughly 0.01 torr. This manuscript presents the results of the equilibrium pressures for the absorption and desorption of hydrogen on zirconium materials at temperatures ranging from 400 C to 600 C. The equilibrium pressures in this temperature region range from 150 mtorr at 600 C to less than 0.1 mtorr at 400 C. It has been shown that the Zircaloy-4 and zirconium samples are extremely prone to surface oxidation prior to and during heating. This oxidation precludes the hydrogen uptake, and therefore samples must be heated under a minimum vacuum of 5 x 10{sup -6} torr. In addition, the Zircaloy-4 samples should be heated at a sufficiently low rate to maintain the system pressure below 0.5 mtorr since an increase in pressure above 0.5 mtorr could possibly hinder the H{sub 2} absorption kinetics due to surface contamination. The results of this study and the details of the testing protocol will be discussed.

Morgan, G.; Korinko, P.

2012-04-03T23:59:59.000Z

224

A study of boiling water flow regimes at low pressures  

E-Print Network [OSTI]

"A comprehensive experimental program to examine flow regimes at pressures below 100 psia for boiling of water in tubes was carried out. An electrical probe, which measures the resistance of the fluid between the centerline ...

Fiori, Mario P.

1966-01-01T23:59:59.000Z

225

Low-pressure spark gap triggered by an ion diode  

DOE Patents [OSTI]

Spark gap apparatus for use as an electric switch operating at high voltage, high current and high repetition rate. Mounted inside a housing are an anode, cathode and ion plate. An ionizable fluid is pumped through the chamber of the housing. A pulse of current to the ion plate causes ions to be emitted by the ion plate, which ions move into and ionize the fluid. Electric current supplied to the anode discharges through the ionized fluid and flows to the cathode. Current stops flowing when the current source has been drained. The ionized fluid recombines into its initial dielectric ionizable state. The switch is now open and ready for another cycle.

Prono, D.S.

1982-08-31T23:59:59.000Z

226

Stable levitation and dynamics of ice particles at low pressures  

E-Print Network [OSTI]

We demonstrate stable levitation and trapping of ice particles of 30~200 micon at low background gas pressures in the presence of a temperature gradient. The thermophoretic force levitates the particles, which have long lifetimes of over an hour. The equilibrium position depends on the background pressure and temperature gradient, which is consistent with theoretical expectations. Furthermore, we investigate interesting launching and merging dynamics of the levitated particles, as well as the development of instability at high background pressures. Our system provides a robust platform to investigate the aggregation of floating ice particles in air, and potentially chemical and biological processes in a microgravity environment.

Nicholas Kowalski; Bernard Xie; Colin V. Parker; Cheng Chin

2015-04-13T23:59:59.000Z

227

Electrical breakdown at low pressure for planar microelectromechanical systems with  

E-Print Network [OSTI]

is a major drawback for the simulation of Microelectromechanical systems (MEMS). However when the Navier

Dalang, Robert C.

228

Low-pressure-ratio regenerative exhaust-heated gas turbine  

SciTech Connect (OSTI)

A design study of coal-burning gas-turbine engines using the exhaust-heated cycle and state-of-the-art components has been completed. In addition, some initial experiments on a type of rotary ceramic-matrix regenerator that would be used to transfer heat from the products of coal combustion in the hot turbine exhaust to the cool compressed air have been conducted. Highly favorable results have been obtained on all aspects on which definite conclusions could be drawn.

Tampe, L.A.; Frenkel, R.G.; Kowalick, D.J.; Nahatis, H.M.; Silverstein, S.M.; Wilson, D.G.

1991-01-01T23:59:59.000Z

229

Alternative Strategies for Low Pressure End Uses | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "ofEarly Career Scientists' ResearchThe OfficeUtility Fed.9-0s) All OtherDepartment ofThis tip sheet outlines

230

Manifestation of constrained dynamics in a low pressure spark  

E-Print Network [OSTI]

Some features of neutron emission from dense plasma focus suggest that the participating deuterons have energy in the range of 105 eV and have a directionality of toroidal motion. Theoretical models of these devices assume that the plasma evolves through a purely irrotational flow and thus fail to predict such solenoidal flow on the scale of the plasma dimensions. Predictions of a relaxation theory are consistent with experimental data [S K H Auluck, Physics of Plasmas,18, 032508 (2011)], but the assumptions upon which it is based are not compatible with known features of these devices. There is thus no satisfactory theoretical construct which provides the necessity for solenoidal flow in these devices. This paper proposes such theoretical construct, namely, the principle of constrained dynamics, and describes an experiment which provides support for this idea. The experiment consisted of low inductance, self-breaking spark discharge in helium at a pressure ~100 hPa between two pointed electrodes separated by...

Auluck, S K H

2013-01-01T23:59:59.000Z

231

Synthesis of YBCO Superconductors Using Low-Pressure Processing - Energy  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security AdministrationcontrollerNanocrystallineForeign Object Damage 3 B.Catalysts. | EMSLInnovation

232

Emergency Filter for Low Pressure EGR | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-UpHeat PumpRecord ofESPC ENABLE: ECMConstruction andElectrolytes76 I Street,lines

233

Sandia National Laboratories: low-pressure metal hydride design  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administration the1developmentturbine blade manufacturinglife-cycleion

234

Crystallization of Sodium Phosphate Dodecahydrate and Re-Crystallization to Natrophosphate in Simulated Hanford Nuclear Waste  

SciTech Connect (OSTI)

The nuclear waste at the Hanford site near Richland, WA, has large concentrations of phosphate in the form of the phosphate ion, sodium phosphate dodecahydrate (Na3PO4.12H2O.(1/4)NaOH) and natrophosphate (Na7F(PO4)3.19H2O). Sodium phosphate dodecahydrate can form a gel and natrophosphate can crystallize large particles, complicating the processing of slurries of both salts. The gel is regarded as more problematic, so natrophosphate has historically been crystallized to prevent phosphate gelling. This study determined that natrophosphate crystals can grow to large size in short time periods (a few weeks), time periods relevant to short process shutdowns. Solutions of NaOH and NaAl(OH)4 were blended at different ratios with stock solutions containing NaOH, NaF, and Na3PO4 at 50 °C. The mixtures were allowed to cool to 22 °C, and the crystal growth was monitored by Polarized Light Microscopy (PLM) for 17 days. Four of the six blends investigated gelled rapidly due to Na3PO4.12H2O.(1/4)NaOH precipitation. The gel slowly dissipated over time as the solids recrystallized into natrophosphate. In one case, the natrophosphate reached sizes of greater than 1000 microns in diameter in just 4 days. This rapid gelling and crystallization kinetics is important to engineers trying to manage nuclear wastes high in phosphates. Hanford tank farm engineers are developing sampling plans to support temperature and process control strategies for preventing the formation of solid phosphates. They are also developing methods of suspending large natrophosphate crystals.

Reynolds, J. G.

2014-12-22T23:59:59.000Z

235

Green Light Pulse Oximeter  

DOE Patents [OSTI]

A reflectance pulse oximeter that determines oxygen saturation of hemoglobin using two sources of electromagnetic radiation in the green optical region, which provides the maximum reflectance pulsation spectrum. The use of green light allows placement of an oximetry probe at central body sites (e.g., wrist, thigh, abdomen, forehead, scalp, and back). Preferably, the two green light sources alternately emit light at 560 nm and 577 nm, respectively, which gives the biggest difference in hemoglobin extinction coefficients between deoxyhemoglobin, RHb, and oxyhemoglobin, HbO.sub.2.

Scharf, John Edward (Oldsmar, FL)

1998-11-03T23:59:59.000Z

236

White light velocity interferometer  

DOE Patents [OSTI]

The invention is a technique that allows the use of broadband and incoherent illumination. Although denoted white light velocimetry, this principle can be applied to any wave phenomenon. For the first time, powerful, compact or inexpensive sources can be used for remote target velocimetry. These include flash and arc lamps, light from detonations, pulsed lasers, chirped frequency lasers, and lasers operating simultaneously in several wavelengths. The technique is demonstrated with white light from an incandescent source to measure a target moving at 16 m/s.

Erskine, David J. (Oakland, CA)

1997-01-01T23:59:59.000Z

237

White light velocity interferometer  

DOE Patents [OSTI]

The invention is a technique that allows the use of broadband and incoherent illumination. Although denoted white light velocimetry, this principle can be applied to any wave phenomenon. For the first time, powerful, compact or inexpensive sources can be used for remote target velocimetry. These include flash and arc lamps, light from detonations, pulsed lasers, chirped frequency lasers, and lasers operating simultaneously in several wavelengths. The technique is demonstrated with white light from an incandescent source to measure a target moving at 16 m/s. 41 figs.

Erskine, D.J.

1997-06-24T23:59:59.000Z

238

White light velocity interferometer  

DOE Patents [OSTI]

The invention is a technique that allows the use of broadband and incoherent illumination. Although denoted white light velocimetry, this principle can be applied to any wave phenomenon. For the first time, powerful, compact or inexpensive sources can be used for remote target velocimetry. These include flash and arc lamps, light from detonations, pulsed lasers, chirped frequency lasers, and lasers operating simultaneously in several wavelengths. The technique is demonstrated with white light from an incandescent source to measure a target moving at 16 m/s.

Erskine, David J. (Oakland, CA)

1999-01-01T23:59:59.000Z

239

White light velocity interferometer  

DOE Patents [OSTI]

The invention is a technique that allows the use of broadband and incoherent illumination. Although denoted white light velocimetry, this principle can be applied to any wave phenomenon. For the first time, powerful, compact or inexpensive sources can be used for remote target velocimetry. These include flash and arc lamps, light from detonations, pulsed lasers, chirped frequency lasers, and lasers operating simultaneously in several wavelengths. The technique is demonstrated with white light from an incandescent source to measure a target moving at 16 m/s. 41 figs.

Erskine, D.J.

1999-06-08T23:59:59.000Z

240

Lakeview Light and Power- Commercial Lighting Rebate Program  

Broader source: Energy.gov [DOE]

Lakeview Light and Power offers a commercial lighting rebate program. Rebates apply to the installation of energy efficient lighting retrofits in non-residential buildings. The rebate program is...

Note: This page contains sample records for the topic "low-pressure sodium lighting" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Clinch River breeder reactor sodium fire protection system design and development  

SciTech Connect (OSTI)

To assure the protection of the public and plant equipment, improbable accidents were hypothesized to form the basis for the design of safety systems. One such accident is the postulated failure of the Intermediate Heat Transfer System (IHTS) piping within the Steam Generator Building (SGB), resulting in a large-scale sodium fire. This paper discusses the design and development of plant features to reduce the consequences of the accident to acceptable levels. Additional design solutions were made to mitigate the sodium spray contribution to the accident scenario. Sodium spill tests demonstrated that large sodium leaks can be safely controlled in a sodium-cooled nuclear power plant.

Foster, K.W.; Boasso, C.J.; Kaushal, N.N.

1984-04-13T23:59:59.000Z

242

Light Vector Mesons  

E-Print Network [OSTI]

This article reviews the current status of experimental results obtained in the measurement of light vector mesons produced in proton-proton and heavy ion collisions at different energies. The review is focused on two phenomena related to the light vector mesons; the modification of the spectral shape in search of Chiral symmetry restoration and suppression of the meson production in heavy ion collisions. The experimental results show that the spectral shape of light vector mesons are modified compared to the parameters measured in vacuum. The nature and the magnitude of the modification depends on the energy density of the media in which they are produced. The suppression patterns of light vector mesons are different from the measurements of other mesons and baryons. The mechanisms responsible for the suppression of the mesons are not yet understood. Systematic comparison of existing experimental results points to the missing data which may help to resolve the problem.

Alexander Milov

2008-12-21T23:59:59.000Z

243

National Synchrotron Light Source  

ScienceCinema (OSTI)

A tour of Brookhaven's National Synchrotron Light Source (NSLS). The NSLS is one of the world's most widely used scientific research facilities, hosting more than 2,500 guest researchers each year. The NSLS provides intense beams of infrared, ultraviole

None

2010-01-08T23:59:59.000Z

244

Efficient Light Sources Today  

E-Print Network [OSTI]

This paper reviews new lamp and lighting technology in terms of application and economic impact. Included are the latest advances in High Intensity Discharge systems, energy saving fluorescent lamps and ballasts, and the new state of the art high...

Hart, A. L.

1982-01-01T23:59:59.000Z

245

Natural lighting and skylights  

E-Print Network [OSTI]

outlined herein, the feasibility of using scale models for studying skylights is also an established fact. The method of analysis by models can be a valuable tool to any designer who is concerned about day-lighting....

Evans, Benjamin Hampton

1961-01-01T23:59:59.000Z

246

Reading Municipal Light Department- Business Lighting Rebate Program  

Broader source: Energy.gov [DOE]

Reading Municipal Light Department (RMLD) offers incentives for non-residential customers to install energy efficient lights and sensors in existing facilities. In addition to rebates for the...

247

Types of Lighting in Commercial Buildings - Lighting Characteristics  

Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

of a light source's accuracy in rendering different colors when compared to a reference light source. The highest attainable CRI is 100. Lamps with CRIs above 70 are...

248

Columbia Water and Light- HVAC and Lighting Efficiency Rebates  

Broader source: Energy.gov [DOE]

Columbia Water and Light (CWL) offers rebates to its commercial and industrial customers for the purchase of high efficiency HVAC installations and efficient lighting. Incentives for certain...

249

Induction Lighting: An Old Lighting Technology Made New Again...  

Broader source: Energy.gov (indexed) [DOE]

around the same time that his rival, Thomas Edison, was working to improve the incandescent light bulb. In the early 1990s, several major lighting manufacturers introduced...

250

Peninsula Light Company- Commercial Efficient Lighting Rebate Program  

Broader source: Energy.gov [DOE]

Peninsula Light Company (PLC) offers a rebate program for commercial customers who wish to upgrade to energy efficient lighting. Participating customers must be served by PLC commercial service....

251

Solid state lighting component  

DOE Patents [OSTI]

An LED component comprising an array of LED chips mounted on a planar surface of a submount with the LED chips capable of emitting light in response to an electrical signal. The LED chips comprise respective groups emitting at different colors of light, with each of the groups interconnected in a series circuit. A lens is included over the LED chips. Other embodiments can comprise thermal spreading structures included integral to the submount and arranged to dissipate heat from the LED chips.

Yuan, Thomas; Keller, Bernd; Ibbetson, James; Tarsa, Eric; Negley, Gerald

2010-10-26T23:59:59.000Z

252

Solid state lighting component  

DOE Patents [OSTI]

An LED component comprising an array of LED chips mounted on a planar surface of a submount with the LED chips capable of emitting light in response to an electrical signal. The LED chips comprise respective groups emitting at different colors of light, with each of the groups interconnected in a series circuit. A lens is included over the LED chips. Other embodiments can comprise thermal spreading structures included integral to the submount and arranged to dissipate heat from the LED chips.

Keller, Bernd; Ibbetson, James; Tarsa, Eric; Negley, Gerald; Yuan, Thomas

2012-07-10T23:59:59.000Z

253

Light and Energy -Daylight measurements  

E-Print Network [OSTI]

Light and Energy - Daylight measurements #12;Light and Energy - Daylight measurements Authors: Jens;3 Title Light and Energy Subtitle Daylight measurements Authors Jens Christoffersen, Ásta Logadóttir ........................................................................................................ 5 Daylight quantity

254

Energy Conservation in Industrial Lighting  

E-Print Network [OSTI]

In order to reduce energy use in lighting Union Carbide recently issued drastically reduced new lighting level standards. A computerized lighting cost program was also developed. Using this program a number of additional energy saving techniques...

Meharg, E.

1979-01-01T23:59:59.000Z

255

Lighting and the Bottom Line  

E-Print Network [OSTI]

A discussion of the cost of light and how it relates to the cost of people. The new Illuminating Engineering Society recommended method of determining lighting levels will be explained. Also several ways of providing good lighting to increase...

Christensen, M.

1981-01-01T23:59:59.000Z

256

Selective Adsorption of Sodium Aluminum Fluoride Salts from Molten Aluminum  

SciTech Connect (OSTI)

Aluminum is produced in electrolytic reduction cells where alumina feedstock is dissolved in molten cryolite (sodium aluminum fluoride) along with aluminum and calcium fluorides. The dissolved alumina is then reduced by electrolysis and the molten aluminum separates to the bottom of the cell. The reduction cell is periodically tapped to remove the molten aluminum. During the tapping process, some of the molten electrolyte (commonly referred as “bath” in the aluminum industry) is carried over with the molten aluminum and into the transfer crucible. The carryover of molten bath into the holding furnace can create significant operational problems in aluminum cast houses. Bath carryover can result in several problems. The most troublesome problem is sodium and calcium pickup in magnesium-bearing alloys. Magnesium alloying additions can result in Mg-Na and Mg-Ca exchange reactions with the molten bath, which results in the undesirable pickup of elemental sodium and calcium. This final report presents the findings of a project to evaluate removal of molten bath using a new and novel micro-porous filter media. The theory of selective adsorption or removal is based on interfacial surface energy differences of molten aluminum and bath on the micro-porous filter structure. This report describes the theory of the selective adsorption-filtration process, the development of suitable micro-porous filter media, and the operational results obtained with a micro-porous bed filtration system. The micro-porous filter media was found to very effectively remove molten sodium aluminum fluoride bath by the selective adsorption-filtration mechanism.

Leonard S. Aubrey; Christine A. Boyle; Eddie M. Williams; David H. DeYoung; Dawid D. Smith; Feng Chi

2007-08-16T23:59:59.000Z

257

Cleaning Cesium Radionuclides from BN-350 Primary Sodium  

SciTech Connect (OSTI)

This paper reports the successful design and operation of a system to remove highly radioactive cesium from the sodium coolant of the BN-350 reactor in Aktau, Kazakhstan. As an international effort between the United States and the Republic of Kazakhstan, a cesium-trapping system was jointly designed, fabricated, installed, and successfully operated. The results are significant for a number of reasons, including (a) a significant reduction of radioactivity levels of the BN-350 coolant and reactor surfaces, thereby reducing exposure to workers during shutdown operations; (b) demonstration of scientific ideas; and (c) the engineering application of effective cesium trap deployment for commercial-sized liquid-metal reactors. About 255 300 GBq (6900 Ci) of cesium was trapped, and the {sup 137}Cs specific activity in BN-350 primary sodium was decreased from 296 MBq/kg (8000 {mu}Ci/kg) to 0.37 MBq/kg (10 {mu}Ci/kg) by using seven cesium traps containing reticulated vitreous carbon (RVC) as the cesium adsorbent. Cesium trapping was accomplished by pumping sodium from the primary circuit, passing it through a block of RVC within each trap, and returning the cleaned sodium to the primary circuit. Both to predict and to analyze the behavior of the cesium traps in the BN-350 reactor primary circuit, a model was developed that satisfactorily describes the observed results of the cesium trapping. By using this model, thermodynamic parameters, such as the heat of adsorption of cesium atoms on RVC and on internal piping surfaces of the BN-350 reactor primary circuit, -22.7 and -5.0 kJ/mole, respectively, were extracted from the experimental data.

Romanenko, O.G.; Allen, K.J.; Wachs, D.M.; Planchon, H.P.; Wells, P.B.; Michelbacher, J.A.; Nazarenko, P.; Dumchev, I.; Maev, V.; Zemtzev, B.; Tikhomirov, L.; Yakovlev, V.; Synkov, A

2005-04-15T23:59:59.000Z

258

Light diffusing fiber optic chamber  

DOE Patents [OSTI]

A light diffusion system for transmitting light to a target area. The light is transmitted in a direction from a proximal end to a distal end by an optical fiber. A diffusing chamber is operatively connected to the optical fiber for transmitting the light from the proximal end to the distal end and transmitting said light to said target area. A plug is operatively connected to the diffusing chamber for increasing the light that is transmitted to the target area.

Maitland, Duncan J. (Lafayette, CA)

2002-01-01T23:59:59.000Z

259

Sodium boiling dryout correlation for LMFBR fuel assemblies  

SciTech Connect (OSTI)

Under certain postulated accident conditions for a Liquid Metal Fast Breeder Reactor (LMFBR), such as the failure of the shutdown heat removal system (SHRS), sodium boiling and clad dryout might occur in the fuel assemblies. It is important to predict the time from boiling inception to dryout, since sustained clad dryout will result in core damage. In this paper a dryout correlation is presented. This correlation is based on 21 boiling tests which resulted in dryout from the THORS BUNDLE 6A, a 19-pin full-length simulated LMFBR fuel assembly and from the THORS Bundle 9, a 61-pin full-length simulated LMFBR fuel assembly. All these tests were performed as follows: for each specified bundle power, an initial steady-state high sodium flow was established, for which sodium boiling did not occur in the bundle. The temperature at the outlet of the test section was approx. 700/sup 0/C. Then, using a programmable pump control system, the flow was reduced to a low value and boiling occurred.

Carbajo, J.J.; Rose, S.D.

1984-01-01T23:59:59.000Z

260

Sodium-Bearing Waste Treatment, Applied Technology Plan  

SciTech Connect (OSTI)

Settlement Agreement between the Department of Energy and the State of Idaho mandates treatment of sodium-bearing waste at the Idaho Nuclear Technology and Engineering Center within the Idaho National Engineering and Environmental Laboratory. One of the requirements of the Settlement Agreement is to complete treatment of sodium-bearing waste by December 31, 2012. Applied technology activities are required to provide the data necessary to complete conceptual design of four identified alternative processes and to select the preferred alternative. To provide a technically defensible path forward for the selection of a treatment process and for the collection of needed data, an applied technology plan is required. This document presents that plan, identifying key elements of the decision process and the steps necessary to obtain the required data in support of both the decision and the conceptual design. The Sodium-Bearing Waste Treatment Applied Technology Plan has been prepared to provide a description/roadmap of the treatment alternative selection process. The plan details the results of risk analyzes and the resulting prioritized uncertainties. It presents a high-level flow diagram governing the technology decision process, as well as detailed roadmaps for each technology. The roadmaps describe the technical steps necessary in obtaining data to quantify and reduce the technical uncertainties associated with each alternative treatment process. This plan also describes the final products that will be delivered to the Department of Energy Idaho Operations Office in support of the office's selection of the final treatment technology.

Lance Lauerhass; Vince C. Maio; S. Kenneth Merrill; Arlin L. Olson; Keith J. Perry

2003-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "low-pressure sodium lighting" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

July 18, 2012 Using QECBs for Street Lighting Upgrades  

E-Print Network [OSTI]

lighting technologies (e.g. light-emitting diodes, induction lighting) can reduce street light energy

262

Efficiency Maine Residential Lighting Program  

Broader source: Energy.gov [DOE]

Efficiency Maine's Residential Lighting Program works directly with retailers and manufacturers to encourage residential customers to purchase energy-efficient lighting. Rebate amounts average $1...

263

Ion Recognition Approach to Volume Reduction of Alkaline Tank Waste by Separation and Recycle of Sodium Hydroxide and Sodium Nitrate  

SciTech Connect (OSTI)

Disposal of high-level nuclear waste is horrendously expensive, in large part because the actual radioactive matter in the tanks has been diluted over 1000-fold by ordinary inorganic chemicals. Treatment processes themselves can exacerbate the problem by adding further volume to the waste. Waste retrieval and sludge washing, for example, will require copious amounts of sodium hydroxide. If the needed sodium hydroxide could be separated from the waste and recycled, however, the addition of fresh sodium hydroxide could be avoided, ultimately reducing the final waste volume and associated disposal costs. The major objective of this research is to explore new liquid-liquid extraction approaches to the selective separation of sodium hydroxide from alkaline high-level wastes stored in underground tanks at the Hanford and Savannah River sites. Consideration is also given to separating potassium and abundant anions, including nitrate, nitrite, aluminate, and carbonate. Salts of these ions represent possible additional value for recycle, alternative disposal, or even use as commodity chemicals. A comprehensive approach toward understanding the extractive chemistry of these salts is envisioned, involving systems of varying complexity, from use of simple solvents to new bifunctional host molecules for ion-pair recognition. These extractants will ideally require no adjustment of the waste composition and will release the extracted salt into water, thereby consuming no additional chemicals and producing no additional waste volume. The overall goal of this research is to provide a scientific foundation upon which the feasibility of new liquid-liquid extraction chemistry applicable to the bulk reduction of the volume of tank waste can be evaluated.

Moyer, Bruce A.; Marchand, Alan P.

2001-06-01T23:59:59.000Z

264

Ion Recognition Approach to Volume Reduction of Alkaline Tank Waste by Separation and Recycle of Sodium Hydroxide and Sodium Nitrate  

SciTech Connect (OSTI)

Disposal of high- level waste is horrendously expensive, in large part because the actual radioactive matter in the tanks has been diluted over 1000-fold by ordinary inorganic chemicals. Treatment processes themselves can exacerbate the problem by adding further volume to the waste. Waste retrieval and sludge washing, for example, will require copious amounts of sodium hydroxide. If the needed sodium hydroxide could be separated from the waste and recycled, however, the addition of fresh sodium hydroxide could be avoided, ultimately reducing the final waste volume and associated disposal costs. The major objective of this research is to explore new liquid- liquid extraction approaches to the selective separation of sodium hydroxide from alkaline high-level wastes stored in underground tanks at the Hanford and Savannah River sites. Consideration is also given to separating potassium and abundant anions, including nitrate, nitrite, aluminate, and carbonate. Salts of these ions represent possible additional value for recycle, alternative disposal, or even use as commodity chemicals. A comprehensive approach toward understanding the extractive chemistry of these salts is envisioned, involving systems of varying complexity, from use of simple solvents to new bifunctional host molecules for ion-pair recognition. These extractants will ideally require no adjustment of the waste composition and will release the extracted salt into water, thereby consuming no additional chemicals and producing no additional waste volume. The overall goal of this research is to provide a scientific foundation upon which the feasibility of new liquid-liquid extraction chemistry applicable to the bulk reduction of the volume of tank waste can be evaluated.

Moyer, Bruce A.; Marchand, Alan P.

2000-06-01T23:59:59.000Z

265

Lighting affects appearance LightSource emits photons  

E-Print Network [OSTI]

1 Lighting affects appearance #12;2 LightSource emits photons Photons travel in a straight line). And then some reach the eye/camera. #12;3 Basic fact: Light is linear Double intensity of sources, double photons reaching eye. Turn on two lights, and photons reaching eye are same as sum of number when each

Jacobs, David

266

ECE 466: LED Lighting Systems -Incandescent lightings rise and  

E-Print Network [OSTI]

versus cost - Power Electronic Drives for CFL and LED light sources to achieve dimmable operation - Basic electric AC and DC circuits at Sophomore level or equivalents Absolutes Lighting System Requirements index as a metric of a light source - Power Electronic Energy sources driving light sources in a compact

Schumacher, Russ

267

Lighting and Surfaces 11.1 Introduction to Lighting  

E-Print Network [OSTI]

-object-at-a-time. "Intrinsic" light is the light emitted by the object itself, such as the glow from a TV screen, a light-emitting diode, or a star. "Ambient" light is an illumination that seems to come from all sides. In the real

Boyd, John P.

268

Sandia National Laboratories: White Light Creation Architectures  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

TechnologiesWhite Light Creation Architectures White Light Creation Architectures Overview of SSL White Light Creation Architectures The entire spectral range of visible light can...

269

Pupillary efficient lighting system  

DOE Patents [OSTI]

A lighting system having at least two independent lighting subsystems each with a different ratio of scotopic illumination to photopic illumination. The radiant energy in the visible region of the spectrum of the lighting subsystems can be adjusted relative to each other so that the total scotopic illumination of the combined system and the total photopic illumination of the combined system can be varied independently. The dilation or contraction of the pupil of an eye is controlled by the level of scotopic illumination and because the scotopic and photopic illumination can be separately controlled, the system allows the pupil size to be varied independently of the level of photopic illumination. Hence, the vision process can be improved for a given level of photopic illumination.

Berman, Samuel M. (San Francisco, CA); Jewett, Don L. (Mill Valley, CA)

1991-01-01T23:59:59.000Z

270

Light harvesting arrays  

DOE Patents [OSTI]

A light harvesting array useful for the manufacture of devices such as solar cells comprises: (a) a first substrate comprising a first electrode; and (b) a layer of light harvesting rods electrically coupled to the first electrode, each of the light harvesting rods comprising a polymer of Formula I: X.sup.1.paren open-st.X.sup.m+1).sub.m (I) wherein m is at least 1, and may be from two, three or four to 20 or more; X.sup.1 is a charge separation group (and preferably a porphyrinic macrocycle, which may be one ligand of a double-decker sandwich compound) having an excited-state of energy equal to or lower than that of X.sup.2, and X.sup.2 through X.sup.m+1 are chromophores (and again are preferably porphyrinic macrocycles).

Lindsey, Jonathan S. (Raleigh, NC)

2002-01-01T23:59:59.000Z

271

Light emitting ceramic device  

DOE Patents [OSTI]

A light-emitting ceramic based panel, hereafter termed "electroceramescent" panel, is herein claimed. The electroceramescent panel is formed on a substrate providing mechanical support as well as serving as the base electrode for the device. One or more semiconductive ceramic layers directly overlay the substrate, and electrical conductivity and ionic diffusion are controlled. Light emitting regions overlay the semiconductive ceramic layers, and said regions consist sequentially of a layer of a ceramic insulation layer and an electroluminescent layer, comprised of doped phosphors or the equivalent. One or more conductive top electrode layers having optically transmissive areas overlay the light emitting regions, and a multi-layered top barrier cover comprising one or more optically transmissive non-combustible insulation layers overlay said top electrode regions.

Valentine, Paul; Edwards, Doreen D.; Walker, Jr., William John; Slack, Lyle H.; Brown, Wayne Douglas; Osborne, Cathy; Norton, Michael; Begley, Richard

2010-05-18T23:59:59.000Z

272

Radioluminescent lighting technology  

SciTech Connect (OSTI)

The glow-in-the-dark stereotype that characterizes the popular image of nuclear materials is not accidental. When the French scientist, Henri Becquerel, first discovered radioactivity in 1896, he was interested in luminescence. Radioluminescence, the production of light from a mixture of energetic and passive materials, is probably the oldest practical application of the unstable nucleus. Tritium-based radioluminescent lighting, in spite of the biologically favorable character of the gaseous tritium isotope, was included in the general tightening of environmental and safety regulations. Tritium light manufacturers would have to meet two fundamental conditions: (1) The benefit clearly outweighed the risk, to the extent that even the perceived risk of a skeptical public would be overcome. (2) The need was significant enough that the customer/user would be willing and able to afford the cost of regulation that was imposed both in the manufacture, use and eventual disposal of nuclear materials. In 1981, researchers at Oak Ridge National Laboratory were investigating larger radioluminescent applications using byproduct nuclear material such as krypton-85, as well as tritium. By 1982, it appeared that large source, (100 Curies or more) tritium gas tube, lights might be useful for marking runways and drop zones for military operations and perhaps even special civilian aviation applications. The successful development of this idea depended on making the light bright enough and demonstrating that large gas tube sources could be used and maintained safely in the environment. This successful DOE program is now in the process of being completed and closed-out. Working closely with the tritium light industry, State governments and other Federal agencies, the basic program goals have been achieved. This is a detailed report of what they have learned, proven, and discovered. 91 refs., 29 figs., 5 tabs. (JF)

Not Available

1990-01-01T23:59:59.000Z

273

MANDATORY MEASURES INDOOR LIGHTING CONTROLS  

E-Print Network [OSTI]

MANDATORY MEASURES INDOOR LIGHTING CONTROLS (Reference: Sub-Chapter 4, Section 130.1) #12;SECTION 4 MANDATORY LIGHTING CONTROLS 1. 130.1 (a) Area Controls: Manual controls that control lighting in each area separately 2. 130.1 (b) Multi-level Controls: Allow occupants to choose the appropriate light level for each

California at Davis, University of

274

MANDATORY MEASURES INDOOR LIGHTING CONTROLS  

E-Print Network [OSTI]

MANDATORY MEASURES INDOOR LIGHTING CONTROLS (Reference: Sub-Chapter 4, Section 130.1) #12;SECTION 3 MANDATORY LIGHTING CONTROLS 1. 130.1 (a) Area Controls: Manual controls that control lighting in each area separately 2. 130.1 (b) Multi-level Controls: "Dimmability." Allow occupants to choose the appropriate light

California at Davis, University of

275

LIGHTING 101 1. Common terminology  

E-Print Network [OSTI]

SECTION 3 LIGHTING 101 1. Common terminology 2. Sources & luminaires 3. Controls #12;SECTION 3SECTION 3 DISCUSSION: COMMON LIGHTING TERMINOLOGY 1. What are the definitions of the following lighting terms? 2. Do you use these terms in professional practice? 3. What other lighting terminology do you use

California at Davis, University of

276

MANDATORY MEASURES INDOOR LIGHTING CONTROLS  

E-Print Network [OSTI]

MANDATORY MEASURES INDOOR LIGHTING CONTROLS (Reference: Sub-Chapter 4, Section 130.1) #12;SECTION 5 MANDATORY LIGHTING CONTROLS 1. Area Controls: Manual controls that control lighting in each area separately 2. Multi-level Controls: Allow occupants to choose the appropriate light level for each area 3. Shut

California at Davis, University of

277

LIGHTING 101 1. Common terminology  

E-Print Network [OSTI]

LIGHTING 101 1. Common terminology 2. Sources and luminaires 3. Controls #12;SECTION 2 DISCUSSION: COMMON LIGHTING TERMINOLOGY 1. What are the definitions of the following lighting terms? 2. Do you use these terms in professional practice? 3. What other lighting terminology do you use on the job? SLIDE 14

California at Davis, University of

278

Extreme Ultraviolet Light Chris Cosio  

E-Print Network [OSTI]

Prospectus Extreme Ultraviolet Light Chris Cosio #12;The field of extreme ultraviolet light (XUV to the way XUV interacts with object, XUV properties are difficult to observe. Extreme ultraviolet light is absorbed by all objects it comes in contact with. Furthermore, extreme ultraviolet light also has low

Hart, Gus

279

On the Criticality Safety of Transuranic Sodium Fast Reactor Fuel Transport Casks  

SciTech Connect (OSTI)

This work addresses the neutronic performance and criticality safety issues of transport casks for fuel pertaining to low conversion ratio sodium cooled fast reactors, conventionally known as Advanced Burner Reactors. The criticality of a one, three, seven and 19-assembly cask capacity is presented. Both dry “helium” and flooded “water” filled casks are considered. No credit for fuel burnup or fission products was assumed. As many as possible of the conservatisms used in licensing light water reactor universal transport casks were incorporated into this SFR cask criticality design and analysis. It was found that at 7-assemblies or more, adding moderator to the SFR cask increases criticality margin. Also, removal of MAs from the fuel increases criticality margin of dry casks and takes a slight amount of margin away for wet casks. Assuming credit for borated fuel tube liners, this design analysis suggests that as many as 19 assemblies can be loaded in a cask if limited purely by criticality safety. If no credit for boron is assumed, the cask could possibly hold seven assemblies if low conversion ratio fast reactor grade fuel and not breeder reactor grade fuel is assumed. The analysis showed that there is a need for new cask designs for fast reactors spent fuel transportation. There is a potential of modifying existing transportation cask design as the starting point for fast reactor spent fuel transportation.

Samuel Bays; Ayodeji Alajo

2010-05-01T23:59:59.000Z

280

The case for endurance testing of sodium-heated steam generators  

SciTech Connect (OSTI)

It is generally believed that a nuclear power comeback before the end of the century will be through the vehicle of the light water reactor (LWR). The newer designs, with their important technical and economic advances, should attract wide interest and result in commercial success for the manufacturers and their utility customers. To develop the liquid-metal fast breeder reactor (LMFBR), approximately $30 billion has been spent worldwide, a third of which has been spent in the US. As a result of this considerable investment, most of the technical obstacles to deployment of the LMFBR have been removed with a few exceptions, one of which is the long-term performance of sodium-heated steam generators. Of the difficulties that have beset the current vintage of nuclear power plants, the performance of steam generators in pressurized water reactors (PWRs) was the most egregious. There was very little development testing and no model testing of PWR steam generators. Development occurred in the plants themselves resulting in many outages and more than $5 billion in lost revenue and replacement power costs. As a result, the electric utility industry is certain to exercise caution regarding acquisition of the LMFBR and will demand strong objective evidence of steam generator reliability. Only long-term endurance testing of prototypic models under prototypic conditions will satisfy this demand.

Onesto, A.T.; Zweig, H.R.; Gibbs, D.C. (Energy Technology Engineering Center, Canoga Park, CA (United States))

1992-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "low-pressure sodium lighting" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Windows and lighting program  

SciTech Connect (OSTI)

More than 30% of all energy use in buildings is attributable to two sources: windows and lighting. Together they account for annual consumer energy expenditures of more than $50 billion. Each affects not only energy use by other major building systems, but also comfort and productivity -- factors that influence building economics far more than does direct energy consumption alone. Windows play a unique role in the building envelope, physically separating the conditioned space from the world outside without sacrificing vital visual contact. Throughout the indoor environment, lighting systems facilitate a variety of tasks associated with a wide range of visual requirements while defining the luminous qualities of the indoor environment. Windows and lighting are thus essential components of any comprehensive building science program. Despite important achievements in reducing building energy consumption over the past decade, significant additional savings are still possible. These will come from two complementary strategies: (1) improve building designs so that they effectively apply existing technologies and extend the market penetration of these technologies; and (2) develop advanced technologies that increase the savings potential of each application. Both the Windows and Daylighting Group and the Lighting System Research Group have made substantial contributions in each of these areas, and continue to do so through the ongoing research summarized here. 23 refs., 16 figs.

Not Available

1990-06-01T23:59:59.000Z

282

Radioluminescent polymer lights  

SciTech Connect (OSTI)

The preparation of radioluminescent light sources where the tritium is located on the aryl-ring in a polymer has been demonstrated with deuterium/tritium substitution. This report discusses tests, results, and future applications of radioluminescent polymers. 10 refs. (FI)

Jensen, G.A.; Nelson, D.A.; Molton, P.M.

1990-09-01T23:59:59.000Z

283

Sweetness and light   

E-Print Network [OSTI]

1. Sweetness and Light. A novel. Judi lives in a nice, clean house with her seventeen year old stepson, who won’t talk to her in anything but monosyllables. His father, Nelson, and she are struggling to relate to each ...

Craig, Katie

2014-07-03T23:59:59.000Z

284

Dynamic stability experiments in sodium-heated steam generators. [LMFBR  

SciTech Connect (OSTI)

Seventy-two dynamic stability tests were performed in the sodium-heated boiling-water test facility at Argonne National Laboratory. A full-scale LMFBR steam generator tube was employed as the test section operating over the water parameter ranges of 6.9 to 15.9 MPa pressure and 170 to 800 kg/m/sup 2/.s mass flux. The stability thresholds from the test compared well to the predictions of a modified version of a correlation equation recently published by other investigators. Typical experimental data and the modified correlation equation are presented.

France, D.M.; Roy, R.; Carlson, R.D.; Chiang, T.

1984-01-01T23:59:59.000Z

285

Interaction Between Trace Metals, Sodium and Sorbents in Combustion.  

SciTech Connect (OSTI)

The proposed research is directed at an understanding of how to exploit interactions between sodium, toxic metals and sorbents, in order to optimize sorbents injection procedures, which can be used to capture and transform these metals into environmentally benign forms. The research will use a 17kW downflow, laboratory combustor, to yield data that can be interpreted in terms of fundamental kinetic mechanisms. Metals to be considered are lead, cadmium, and arsenic. Sorbents will be kaolinite, bauxite, and limestone. The role of sulfur will also be determined.

Wendt, O.L.; Davis, S.

1997-10-17T23:59:59.000Z

286

Nanofriction on Sodium Polystyrene Sulfonate Brushes in Water  

E-Print Network [OSTI]

We investigated the frictional properties of sodium polystyrene sulfonate (NaPSS) brushes in water by frictional force microscopy (FFM). Polyelectrolyte brushes were prepared on silicon wafers by the grafting-to method. The brushes considerably reduce the frictional force and coefficient of kinetic friction compared to hydrodynamic lubrication on a smooth Si wafer. Frictional force is independent of sliding speed, but is lower for lower degrees of NaPSS polymerization. Nanoindentation tests indicate that the polymer chains in a brush are stretched strongly away from the substrate. These results suggest that polymer chains point support the FFM probe tip in water and reduced contact area and friction.

Takuya Fujima; Eitaro Futakuchi; Fumihiro Kino

2014-02-19T23:59:59.000Z

287

Sodium Ion Insertion in Hollow Carbon Nanowires for Battery Applications. |  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administrationcontroller systemsBiSite CulturalDepartment ofat Home |EMSL Sodium Ion Insertion

288

Conceptual design of a pressure tube light water reactor with variable moderator control  

SciTech Connect (OSTI)

This paper presents the development of innovative pressure tube light water reactor with variable moderator control. The core layout is derived from a CANDU line of reactors in general, and advanced ACR-1000 design in particular. It should be stressed however, that while some of the ACR-1000 mechanical design features are adopted, the core design basics of the reactor proposed here are completely different. First, the inter fuel channels spacing, surrounded by the calandria tank, contains a low pressure gas instead of heavy water moderator. Second, the fuel channel design features an additional/external tube (designated as moderator tube) connected to a separate moderator management system. The moderator management system is design to vary the moderator tube content from 'dry' (gas) to 'flooded' (light water filled). The dynamic variation of the moderator is a unique and very important feature of the proposed design. The moderator variation allows an implementation of the 'breed and burn' mode of operation. The 'breed and burn' mode of operation is implemented by keeping the moderator tube empty ('dry' filled with gas) during the breed part of the fuel depletion and subsequently introducing the moderator by 'flooding' the moderator tube for the 'burn' part. This paper assesses the conceptual feasibility of the proposed concept from a neutronics point of view. (authors)

Rachamin, R.; Fridman, E. [Reactor Safety Div., Inst. of Resource Ecology, Helmholtz-Zentrum Dresden-Rossendorf, POB 51 01 19, 01314 Dresden (Germany); Galperin, A. [Dept. of Nuclear Engineering, Ben-Gurion Univ. of the Negev, POB 653, Beer Sheva 84105 (Israel)

2012-07-01T23:59:59.000Z

289

ELECTROCHEMICAL RESEARCH IN CHEMICAL HYDROGEN STORAGE MATERIALS: SODIUM BOROHYDRIDE AND ORGANOTIN HYDRIDES.  

E-Print Network [OSTI]

??Chemical storage of hydrogen involves release of hydrogen in a controlled manner from materials in which the hydrogen is covalently bound. Sodium borohydride and aminoborane… (more)

McLafferty, Jason

2009-01-01T23:59:59.000Z

290

E-Print Network 3.0 - affecting sodium hypochlorite Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Workshop Summary: equipment, vehicles Sodium hypochlorite (bleach) 200-500 ppm Nets, boots, clothing. Surfaces must be clean... hypochlorite solution.Note: Bleach is 5.25%...

291

E-Print Network 3.0 - alkaline sodium borohydride Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Aardahl, PNNL) The most critical hurdle for the use of sodium ... Source: DOE Office of Energy Efficiency and Renewable Energy, Hydrogen, Fuel Cells and Infrastructure...

292

E-Print Network 3.0 - aluminum sodium chloride Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

agents Water Acetyl chloride, alkaline and alkaline... hypochlorite, all oxidizing agents Carbon tetrachloride Sodium ... Source: Hall, Sharon J. - School of Life Sciences, Arizona...

293

REACTIONS OF SODIUM PEROXIDE WITH COMPONENTS OF LEGACY PLUTONIUM MATERIALS  

SciTech Connect (OSTI)

Plutonium oxide (PuO{sub 2}) calcined at >900 C resists dissolution in nitric acid (HNO{sub 3})-potassium fluoride (KF) solutions, a common method for their dissolution. The Savannah River National Laboratory (SRNL) has developed an alternate method for large samples of PuO{sub 2}-bearing materials using sodium peroxide (Na{sub 2}O{sub 2}) fusion as a pretreatment. The products of the reaction between Na{sub 2}O{sub 2} and PuO{sub 2} have been reported in the literature. As part of the SRNL development effort, additional data about the reaction between Na{sub 2}O{sub 2} and PuO{sub 2} were required. Also needed were data concerning the reaction of Na{sub 2}O{sub 2} with other components that may be present in the feed materials. Sodium peroxide was reacted with aluminum metal (Al), beryllium metal (Be), graphite, potassium chloride (KCl), magnesium chloride (MgCl{sub 2}), and calcium chloride (CaCl{sub 2}). The paper reports and discusses the reaction products of these and related compounds with Na{sub 2}O{sub 2}.

Pierce, R.; Missimer, D.; Crowder, M.

2011-10-04T23:59:59.000Z

294

Sodium fast reactor safety and licensing research plan. Volume I.  

SciTech Connect (OSTI)

This report proposes potential research priorities for the Department of Energy (DOE) with the intent of improving the licensability of the Sodium Fast Reactor (SFR). In support of this project, five panels were tasked with identifying potential safety-related gaps in available information, data, and models needed to support the licensing of a SFR. The areas examined were sodium technology, accident sequences and initiators, source term characterization, codes and methods, and fuels and materials. It is the intent of this report to utilize a structured and transparent process that incorporates feedback from all interested stakeholders to suggest future funding priorities for the SFR research and development. While numerous gaps were identified, two cross-cutting gaps related to knowledge preservation were agreed upon by all panels and should be addressed in the near future. The first gap is a need to re-evaluate the current procedures for removing the Applied Technology designation from old documents. The second cross-cutting gap is the need for a robust Knowledge Management and Preservation system in all SFR research areas. Closure of these and the other identified gaps will require both a reprioritization of funding within DOE as well as a re-evaluation of existing bureaucratic procedures within the DOE associated with Applied Technology and Knowledge Management.

Sofu, Tanju (Argonne National Laboratory, Argonne, IL); LaChance, Jeffrey L.; Bari, R. (Brokhaven National Laboratory Upton, NY); Wigeland, Roald (Idaho National Laboratory, Idaho Falls, ID); Denman, Matthew R.; Flanagan, George F. (Oak Ridge National Laboratory, Oak Ridge, TN)

2012-05-01T23:59:59.000Z

295

Preliminary engineering design of sodium-cooled CANDLE core  

SciTech Connect (OSTI)

The CANDLE burning process is characterized by the autonomous shifting of burning region with constant reactivity and constant spacial power distribution. Evaluations of such critical burning process by using widely used neutron diffusion and burning codes under some realistic engineering constraints are valuable to confirm the technical feasibility of the CANDLE concept and to put the idea into concrete core design. In the first part of this paper, it is discussed that whether the sustainable and stable CANDLE burning process can be reproduced even by using conventional core analysis tools such as SLAROM and CITATION-FBR. As a result, it is certainly possible to demonstrate it if the proper core configuration and initial fuel composition required as CANDLE core are applied to the analysis. In the latter part, an example of a concrete image of sodium cooled, metal fuel, 2000MWt rating CANDLE core has been presented by assuming an emerging inevitable technology of recladding. The core satisfies engineering design criteria including cladding temperature, pressure drop, linear heat rate, and cumulative damage fraction (CDF) of cladding, fast neutron fluence and sodium void reactivity which are defined in the Japanese FBR design project. It can be concluded that it is feasible to design CANDLE core by using conventional codes while satisfying some realistic engineering design constraints assuming that recladding at certain time interval is technically feasible.

Takaki, Naoyuki; Namekawa, Azuma; Yoda, Tomoyuki; Mizutani, Akihiko; Sekimoto, Hiroshi [Department of Nuclear Engineering, Tokai University, Kitakaname, Hiratsuka, Kanagawa 259-1292 (Japan); AISA, Fuchu, Ishioka, Ibaraki 315-0013 (Japan); Research Laboratory for Nuclear Reactors, Tokyo Institute of Technology, Ookayama, Meguro-ku, Tokyo, 152-8550 (Japan)

2012-06-06T23:59:59.000Z

296

TRUEX partitioning studies applied to ICPP sodium-bearing waste  

SciTech Connect (OSTI)

The Idaho Chemical Processing Plant (ICPP), located in southeast Idaho at the USDOE Idaho National Engineering Laboratory, formerly reprocessed highly enriched spent nuclear fuel to recover fissionable uranium. The HLW raffinates from the combined PUREX/REDOX type uranium recovery process were converted to solid oxides (calcine) in a high temperature fluidized bed. Liquid effluents from the calcination process were combined with liquid sodium bearing waste (SBW) generated primarily in conjunction with decontamination activities. Due to the high sodium content in the SBW, this secondary waste stream is not directly amenable to solidification via calcination. Currently, approximately 1.5 millon gallons of liquid SBW are stored at the ICPP in large tanks. Several treatment options for the SBW are currently being considered, including the TRansUranic EXtraction (TRUEX) process developed by Horwitz and co-workers at Argonne National Laboratory (ANL), in preparation for the final disposition of SBW. Herein described are experimental results of radionuclide tracer studies with simulated SBW using the TRUEX process solvent.

Herbst, R.S.; Brewer, K.N.; Law, J.D.; Tranter, T.J.; Todd, T.A.

1994-05-01T23:59:59.000Z

297

Selection of materials for sodium fast reactor steam generators  

SciTech Connect (OSTI)

Sodium Fast Reactor (SFR) is considered in France as the most mature technology of the different Generation IV systems. In the short-term the designing work is focused on the identification of the potential tracks to demonstrate licensing capability, availability, in-service inspection capability and economical performance. In that frame materials selection for the major components, as the steam generator, is a particularly key point managed within a French Research and Development program launched by AREVA, CEA and EDF. The choice of the material for the steam generator is indeed complex because various aspects shall be considered like mechanical and thermal properties at high temperature, interaction with sodium on one side and water and steam on the other side, resistance to wastage, procurement, fabrication, weldability and ability for inspection and in-situ intervention. The following relevant options are evaluated: the modified 9Cr1Mo ferritic-martensitic grade and the Alloy 800 austenitic grade. The objective of this paper is to assess for both candidates their abilities to reach the current SFR needs regarding material design data, from AFCEN RCC-MRx Code in particular, compatibility with environments and manufacturability. (authors)

Dubiez-Le Goff, S.; Garnier, S.; Gelineau, O. [AREVA (France); Dalle, F. [Commissariat a l'energie atomique et aux energies alternatives - CEA (France); Blat-Yrieix, M.; Augem, J. M. [Electricite de France - EDF (France)

2012-07-01T23:59:59.000Z

298

Light cone matrix product  

SciTech Connect (OSTI)

We show how to combine the light-cone and matrix product algorithms to simulate quantum systems far from equilibrium for long times. For the case of the XXZ spin chain at {Delta} = 0.5, we simulate to a time of {approx} 22.5. While part of the long simulation time is due to the use of the light-cone method, we also describe a modification of the infinite time-evolving bond decimation algorithm with improved numerical stability, and we describe how to incorporate symmetry into this algorithm. While statistical sampling error means that we are not yet able to make a definite statement, the behavior of the simulation at long times indicates the appearance of either 'revivals' in the order parameter as predicted by Hastings and Levitov (e-print arXiv:0806.4283) or of a distinct shoulder in the decay of the order parameter.

Hastings, Matthew B [Los Alamos National Laboratory

2009-01-01T23:59:59.000Z

299

OLEDS FOR GENERAL LIGHTING  

SciTech Connect (OSTI)

The goal of this program was to reduce the long term technical risks that were keeping the lighting industry from embracing and developing organic light-emitting diode (OLED) technology for general illumination. The specific goal was to develop OLEDs for lighting to the point where it was possible to demonstrate a large area white light panel with brightness and light quality comparable to a fluorescence source and with an efficacy comparable to that of an incandescent source. it was recognized that achieving this would require significant advances in three area: (1) the improvement of white light quality for illumination, (2) the improvement of OLED energy efficiency at high brightness, and (3) the development of cost-effective large area fabrication techniques. The program was organized such that, each year, a ''deliverable'' device would be fabricated which demonstrated progress in one or more of the three critical research areas. In the first year (2001), effort concentrated on developing an OLED capable of generating high illumination-quality white light. Ultimately, a down-conversion method where a blue OLED was coupled with various down-conversion layers was chosen. Various color and scattering models were developed to aid in material development and device optimization. The first year utilized this approach to deliver a 1 inch x 1 inch OLED with higher illumination-quality than available fluorescent sources. A picture of this device is shown and performance metrics are listed. To their knowledge, this was the first demonstration of true illumination-quality light from an OLED. During the second year, effort concentrated on developing a scalable approach to large area devices. A novel device architecture consisting of dividing the device area into smaller elements that are monolithically connected in series was developed. In the course of this development, it was realized that, in addition to being scalable, this approach made the device tolerant to the most common OLED defect--electrical shorts. This architecture enabled the fabrication of a 6 inch x 6 inch OLED deliverable for 2002. A picture of this deliverable is shown and the performance metrics are listed. At the time, this was the highest efficiency, highest lumen output illumination-quality OLED in existence. The third year effort concentrated on improving the fabrication yield of the 6 inch x 6 inch devices and improving the underlying blue device efficiency. An efficiency breakthrough was achieved through the invention of a new device structure such that now 15 lumen per watt devices could be fabricated. A 2 feet x 2 feet OLED panel consisting of sixteen 6 inch x 6 inch high efficiency devices tiled together was then fabricated. Pictures of this panel are shown with performance metrics listed. This panel met all project objectives and was the final deliverable for the project. It is now the highest efficiency, highest lumen output, illumination-quality OLED in existence.

Anil Duggal; Don Foust; Chris Heller; Bill Nealon; Larry Turner; Joe Shiang; Nick Baynes; Tim Butler; Nalin Patel

2004-02-29T23:59:59.000Z

300

Fusion pumped light source  

DOE Patents [OSTI]

Apparatus is provided for generating energy in the form of light radiation. A fusion reactor is provided for generating a long, or continuous, pulse of high-energy neutrons. The neutron flux is coupled directly with the lasing medium. The lasing medium includes a first component selected from Group O of the periodic table of the elements and having a high inelastic scattering cross section. Gamma radiation from the inelastic scattering reactions interacts with the first component to excite the first component, which decays by photon emission at a first output wavelength. The first output wavelength may be shifted to a second output wavelength using a second liquid component responsive to the first output wavelength. The light outputs may be converted to a coherent laser output by incorporating conventional optics adjacent the laser medium.

Pappas, Daniel S. (Los Alamos, NM)

1989-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "low-pressure sodium lighting" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Turbo-Charged Lighting Design  

E-Print Network [OSTI]

TURBO-CHARGED LIGHTING DESIGN William H. Clark II Design Engineer O'Connell Robertson & Assoc Austin/ Texas ABSTRACT The task of the lighting designer has become very complex, involving thousands of choices for fixture types and hundreds...

Clark, W. H. II

302

Faster than Light Quantum Communication  

E-Print Network [OSTI]

Faster than light communication might be possible using the collapse of the quantum wave-function without any accompanying paradoxes.

A. Y. Shiekh

2008-04-05T23:59:59.000Z

303

Webinar: Fuel Cell Mobile Lighting  

Broader source: Energy.gov [DOE]

Video recording of the Fuel Cell Technologies Office webinar, Fuel Cell Mobile Lighting, originally presented on November 13, 2012.

304

Photodetector with enhanced light absorption  

DOE Patents [OSTI]

A photodetector including a light transmissive electrically conducting layer having a textured surface with a semiconductor body thereon. This layer traps incident light thereby enhancing the absorption of light by the semiconductor body. A photodetector comprising a textured light transmissive electrically conducting layer of SnO.sub.2 and a body of hydrogenated amorphous silicon has a conversion efficiency about fifty percent greater than that of comparative cells. The invention also includes a method of fabricating the photodetector of the invention.

Kane, James (Lawrenceville, NJ)

1985-01-01T23:59:59.000Z

305

MANDATORY MEASURES OUTDOOR LIGHTING CONTROLS  

E-Print Network [OSTI]

MANDATORY MEASURES OUTDOOR LIGHTING CONTROLS (Reference: Sub-Chapter 4, Section 130.2) #12;SECTION level of each multi-tier garage. · General lighting must have occupant sensing controls with at least one control step between 20% and 50% of design lighting power · No more than 500 watts of rated

California at Davis, University of

306

MANDATORY MEASURES OUTDOOR LIGHTING CONTROLS  

E-Print Network [OSTI]

MANDATORY MEASURES OUTDOOR LIGHTING CONTROLS (Reference: Sub-Chapter 4, Section 130.2) #12;SECTION 5 Additions and Alterations Any alteration that increases the connected lighting load must meet all No measures required OUTDOOR LIGHTING11/20/2014 #12;SECTION 5 BACKLIGHT, UPLIGHT, AND GLARE (BUG) RATINGS

California at Davis, University of

307

MANDATORY MEASURES OUTDOOR LIGHTING CONTROLS  

E-Print Network [OSTI]

MANDATORY MEASURES OUTDOOR LIGHTING CONTROLS (Reference: Sub-Chapter 4, Section 130.2) #12;SECTION performance in relation to lighting trespass, sky glow, and high angle brightness. This is necessary in order to reduce light pollution, which has a negative effect on wildlife and the surrounding environments

California at Davis, University of

308

Arnold Schwarzenegger, LIGHTING RESEARCH PROGRAM  

E-Print Network [OSTI]

;#12;Prepared By: Lighting Research Center Andrew Bierman, Project Lead Troy, New York 12180 Managed ByArnold Schwarzenegger, Governor LIGHTING RESEARCH PROGRAM PROJECT 3.2 ENERGY EFFICIENT LOAD- SHEDDING LIGHTING TECHNOLOGY Prepared For: California Energy Commission Public Interest Energy Research

309

STATE OF CALIFORNIA RESIDENTIAL LIGHTING  

E-Print Network [OSTI]

STATE OF CALIFORNIA RESIDENTIAL LIGHTING CEC-CF-6R-LTG-01 (Revised 08/09) CALIFORNIA ENERGY COMMISSION INSTALLATION CERTIFICATE CF-6R-LTG-01 Residential Lighting (Page 1 of 6) Site Address: Enforcement Agency: Permit Number: 2008 Residential Compliance Forms August 2009 1. Kitchen Lighting Does project

310

4June2013 Page 1 of 8 Sodium Hydroxide (Pellets) SOP Standard Operating Procedures  

E-Print Network [OSTI]

4June2013 Page 1 of 8 Sodium Hydroxide (Pellets) SOP Standard Operating Procedures Strong Corrosives ­ Strong Bases (SB) Sodium Hydroxide (Pellets) PrintOH Form: pellets Color: white Melting point/freezing point: 318 °C (604 °F

Cohen, Ronald C.

311

Sequential Treatment by Ionizing Radiation and Sodium Arsenite Dramatically Accelerates TRAIL-Mediated Apoptosis of  

E-Print Network [OSTI]

is critically important in the translocation of death receptor to the cell surface. Moreover, sodium arsenite and further down-regulates cFLIP levels in melanoma cells. We have evaluated the effects of sequentialSequential Treatment by Ionizing Radiation and Sodium Arsenite Dramatically Accelerates TRAIL

312

Effect of sodium chloride concentration on the heat resistance and recovery of  

E-Print Network [OSTI]

Effect of sodium chloride concentration on the heat resistance and recovery of Salmonella inhibitory effect in the recovery media. Keywords : Salmonella typhimurium, Sodium chloride, Heat treatment, but they also generate damaged cells. The ability of heated cells to survive depends on the recovery conditions

Paris-Sud XI, Université de

313

Atomistic structure of sodium and calcium silicate intergranular films in alumina  

E-Print Network [OSTI]

Atomistic structure of sodium and calcium silicate intergranular films in alumina David A. Litton March 1998; accepted 21 October 1998) Sodium silicate intergranular films (IGF) in contact. The results were compared to previous simulations of calcium silicate and sol-gel silica IGF's in contact

Garofalini, Stephen H.

314

Sodium fast reactor fuels and materials : research needs.  

SciTech Connect (OSTI)

An expert panel was assembled to identify gaps in fuels and materials research prior to licensing sodium cooled fast reactor (SFR) design. The expert panel considered both metal and oxide fuels, various cladding and duct materials, structural materials, fuel performance codes, fabrication capability and records, and transient behavior of fuel types. A methodology was developed to rate the relative importance of phenomena and properties both as to importance to a regulatory body and the maturity of the technology base. The technology base for fuels and cladding was divided into three regimes: information of high maturity under conservative operating conditions, information of low maturity under more aggressive operating conditions, and future design expectations where meager data exist.

Denman, Matthew R.; Porter, Douglas (Idaho National Laboratory, Idaho Falls, ID); Wright, Art (Argonne National Laboratory Argonne, IL); Lambert, John (Argonne National Laboratory Argonne, IL); Hayes, Steven (Idaho National Laboratory, Idaho Falls, ID); Natesan, Ken (Argonne National Laboratory Argonne, IL); Ott, Larry J. (Oak Ridge National Laboratory, Oak Ridge, TN); Garner, Frank (Radiation Effects Consulting. Richland, WA); Walters, Leon (Advanced Reactor Concepts, Idaho Falls, ID); Yacout, Abdellatif (Argonne National Laboratory Argonne, IL)

2011-09-01T23:59:59.000Z

315

Sodium-Bearing Waste Treatment Alternatives Implementation Study  

SciTech Connect (OSTI)

The purpose of this document is to discuss issues related to the implementation of each of the five down-selected INEEL/INTEC radioactive liquid waste (sodium-bearing waste - SBW) treatment alternatives and summarize information in three main areas of concern: process/technical, environmental permitting, and schedule. Major implementation options for each treatment alternative are also identified and briefly discussed. This report may touch upon, but purposely does not address in detail, issues that are programmatic in nature. Examples of these include how the SBW will be classified with respect to the Nuclear Waste Policy Act (NWPA), status of Waste Isolation Pilot Plant (WIPP) permits and waste storage availability, available funding for implementation, stakeholder issues, and State of Idaho Settlement Agreement milestones. It is assumed in this report that the SBW would be classified as a transuranic (TRU) waste suitable for disposal at WIPP, located in New Mexico, after appropriate treatment to meet transportation requirements and waste acceptance criteria (WAC).

Charles M. Barnes; James B. Bosley; Clifford W. Olsen

2004-07-01T23:59:59.000Z

316

Feasibility Study for Vitrification of Sodium-Bearing Waste  

SciTech Connect (OSTI)

Treatment of sodium-bearing waste (SBW) at the Idaho Nuclear Technology and Engineering Center (INTEC) within the Idaho National Engineering and Environmental Laboratory is mandated under a Settlement Agreement between the Department of Energy and the State of Idaho. One of the requirements of the Settlement Agreement is the complete calcination (i.e., treatment) of all SBW by December 31, 2012. One of the proposed options for treatment of SBW is vitrification. This study will examine the viability of SBW vitrification. This study describes the process and facilities to treat the SBW, from beginning waste input from INTEC Tank Farm to the final waste forms. Schedules and cost estimates for construction and operation of a Vitrification Facility are included. The study includes a facility layout with drawings, process description and flow diagrams, and preliminary equipment requirements and layouts.

J. J. Quigley; B. D. Raivo; S. O. Bates; S. M. Berry; D. N. Nishioka; P. J. Bunnell

2000-09-01T23:59:59.000Z

317

Sodium Heat Engine Development Program. Phase 1, Final report  

SciTech Connect (OSTI)

The Sodium Heat Engine (SHE) is an efficient thermoelectric conversion device which directly generates electricity from a thermally regenerative electrochemical cell that relies on the unique conduction properties of {beta}{double_prime}-alumina solid electrolyte (BASE). Laboratory models of a variety of SHE devices have demonstrated the feasibility and efficiency of the system, engineering development of large prototype devices has been slowed by a series of materials and fabrication problems. Failure of the electrolyte tubes has been a recurring problem and a number of possible causes have been postulated. To address these issues, a two-phase engineering development program was undertaken. This report summarizes the final results of the first phase of the program, which included extensive materials characterization activities, a study of applicable nondestructive evaluation methods, an investigation of possible stress states that would contribute to fracture, and certain operational issues associated with the electromagnetic pumps used in the SHE prototype. Mechanical and microstructural evaluation of commercially obtained BASE tubes revealed that they should be adequate for SHE applications and that sodium exposure produced no appreciable deleterious strength effects. Processing activities to produce a more uniform and smaller grain size for the BASE tubes were completed using isostatic pressing, extrusion, and slip casting. Green tubes were sintered by conventional and microwave plasma methods. Of particular interest is the residual stress state in the BASE tubes, and both analysis and nondestructive evaluation methods were employed to evaluate these stresses. X-ray and neutron diffraction experiments were performed to determine the bulk residual stresses in commercially fabricated BASE tubes; however, tube-to-tube variations and variations among the various methods employed did not allow formulation of a definitive definition of the as-fabricated stress state.

Singh, J.P.; Kupperman, D.S.; Majumdar, S.; Dorris, S.; Gopalsami, N.; Dieckman, S.L.; Jaross, R.A.; Johnson, D.L.; Gregar, J.S.; Poeppel, R.B.; Raptis, A.C.; Valentin, R.A.

1992-01-01T23:59:59.000Z

318

105-DR Large Sodium Fire Facility closure plan. Revision 1  

SciTech Connect (OSTI)

The Hanford Site, located northwest of the city of Richland, Washington, houses reactors, chemical-separation systems, and related facilities used for the production of special nuclear materials, and activities associated with nuclear energy development. The 105-DR Large Sodium Fire Facility (LSFF), which was in operation from about 1972 to 1986, was a research laboratory that occupied the former ventilation supply room on the southwest side of the 105-DR Reactor facility. The LSFF was established to provide a means of investigating fire and safety aspects associated with large sodium or other metal alkali fires in the liquid metal fast breeder reactor (LMFBR) facilities. The 105-DR Reactor facility was designed and built in the 1950`s and is located in the 100-D Area of the Hanford Site. The building housed the 105-DR defense reactor, which was shut down in 1964. The LSFF was initially used only for engineering-scale alkali metal reaction studies. In addition, the Fusion Safety Support Studies program sponsored intermediate-size safety reaction tests in the LSFF with lithium and lithium lead compounds. The facility has also been used to store and treat alkali metal waste, therefore the LSFF is subject to the regulatory requirements for the storage and treatment of dangerous waste. Closure will be conducted pursuant to the requirements of the Washington Administrative Code (WAC) 173-303-610. This closure plan presents a description of the facility, the history of waste managed, and the procedures that will be followed to close the LSFF as an Alkali Metal Treatment Facility. No future use of the LSFF is expected.

Not Available

1993-05-01T23:59:59.000Z

319

Pedestrian Friendly Outdoor Lighting  

SciTech Connect (OSTI)

This GATEWAY report discusses the problems of pedestrian lighting that occur with all technologies with a focus on the unique optical options and opportunities offered by LEDs through the findings from two pedestrian-focused projects, one at Stanford University in California, and one at the Chautauqua Institution in upstate New York. Incorporating user feedback this report reviews the tradeoffs that must be weighed among visual comfort, color, visibility, efficacy and other factors to stimulate discussion among specifiers, users, energy specialists, and in industry in hopes that new approaches, metrics, and standards can be developed to support pedestrian-focused communities, while reducing energy use.

Miller, Naomi J.; Koltai, Rita; McGowan, Terry

2013-12-31T23:59:59.000Z

320

Advances in Lighting  

E-Print Network [OSTI]

colour rendition. The quartz-halogen incandescent lam s operate at higher temperatures, and have a somewhat higher efficacy, but they are rarely used except for special applicati ns. 3-2 High Intensity Discharge Lamps. Mercury is the grandfather... of the H.I.D. lamps. Its blue-green light, has been used almost exclusively for streetlighti and, often with colour-improving phospho it is still being used in industrial and commercial applications. Reactor-type ballasted mercury lamps can now...

Tumber, A. J.

1981-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "low-pressure sodium lighting" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Lights, Conformational Change... Action!  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: VegetationEquipment Surfaces and Interfaces Sample6, 2011 LawrenceEfeedstocksHomesLighting the

322

Lighting | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of InspectorConcentrating Solar Powerstories on climateJuno Beach,October,Lighthouse Solar Jump to:Lighting Jump

323

Ecological Consequences of Artificial Night Lighting  

E-Print Network [OSTI]

of Artificial Night Lighting Catherine Rich and Travisof artificial night lighting. This book provides editedage of modern urban lighting was ushered in. Coincidentally,

Piselli, Kathy

2006-01-01T23:59:59.000Z

324

LIGHTING CONTROLS: SURVEY OF MARKET POTENTIAL  

E-Print Network [OSTI]

REFERENCES Task Report to Lighting Systems Research,Berkeley Laboratory, "Lighting Control System Market1980). Task Report to Lighting Systems Research, Lawrence

Verderber, R.R.

2010-01-01T23:59:59.000Z

325

Demand Responsive Lighting: A Scoping Study  

E-Print Network [OSTI]

3 3.0 Previous Experience with Demand Responsive Lighting11 4.3. Prevalence of Lighting13 4.4. Impact of Title 24 on Lighting

Rubinstein, Francis; Kiliccote, Sila

2007-01-01T23:59:59.000Z

326

Municipal Consortium LED Street Lighting Workshop Presentations...  

Broader source: Energy.gov (indexed) [DOE]

A Rational View of LM-79 Reports, IES Files, and Product Variation Gary Steinberg, GE Lighting Solutions Solid-State Street Lighting: Calculating Light Loss Factors Dana Beckwith,...

327

Municipal Consortium LED Street Lighting Workshop Presentations...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

National Association of Energy Services Companies Calculating Light Loss Factors for Solid-State Lighting Systems Chad Stalker, Philips Lumileds Lighting Intro to MSSLC's...

328

Sandia National Laboratories: Light Creation Materials  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

TechnologiesLight Creation Materials Light Creation Materials Overview of SSL Light Creation Materials Different families of inorganic semiconductor materials can...

329

Photon echo studies of photosynthetic light harvesting  

E-Print Network [OSTI]

of the B800-B820 light-harvesting complex. Proc Natl Acadphotosynthetic light harvesting Elizabeth L. Read Æ Hohjaitransfer events in light harvesting. Here, we outline the

Read, Elizabeth L.; Lee, Hohjai; Fleming, Graham R.

2009-01-01T23:59:59.000Z

330

Sandia National Laboratories: Light Creation Materials  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

EFRCOverviewLight Creation Materials Light Creation Materials Overview of SSL Light Creation Materials Different families of inorganic semiconductor materials can contribute to...

331

Ion Recognition Approach to Volume Reduction of Alkaline Tank Waste by Separation and Recycle of Sodium Hydroxide and Sodium Nitrate  

SciTech Connect (OSTI)

The objective of this research is to explore new liquid-liquid extraction approaches to the selective separation of major sodium salts from alkaline high-level wastes stored in underground tanks at Hanford, Savannah River, and Oak Ridge sites. Disposal of high level waste is horrendously expensive, in large part because the actual radioactive matter in the tanks has been diluted over 1000-fold by ordinary inorganic chemicals. Since the residual bulk chemicals must still undergo expensive treatment and disposal after most of the hazardous radionuclides have been removed, large cost savings will result from processes that reduce the overall waste volume. It is proposed that major cost savings can be expected if sodium hydroxide needed for sludge washing can be obtained from the waste itself, thus avoiding the addition of yet another bulk chemical to the waste and still further increase of the waste volume and disposal cost. Secondary priority is given to separating potassium an d abundant anions, including nitrate, nitrite, aluminate, and carbonate. Salts of these ions represent possible additional value for recycle, alternative disposal, or even use as commodity chemicals. A comprehensive approach toward understanding the extractive chemistry of these salts is envisioned, involving systems of varying complexity, from use of simple solvents to new bifunctional host molecules for ion-pair recognition. These extractants will ideally require no adjustment of the waste composition and will release the extracted salt into water, thereby consuming no additional chemicals and producing no additional waste volume. The overall goal of this research is to provide a scientific foundation upon which the feasibility of new liquid-liquid extraction chemistry applicable to the bulk reduction of the volume of tank waste can be evaluated.

Moyer, Bruce A.; Marchand, Alan P.; Bryan, Jeffrey C.; Bonnesen, Peter V.

1999-06-01T23:59:59.000Z

332

Mercury's sodium exosphere: Magnetospheric ion recycling Service d'Aeronomie du CNRS/IPSL, Verrie`res-Le-Buisson, France  

E-Print Network [OSTI]

Mercury's sodium exosphere: Magnetospheric ion recycling F. Leblanc Service d'Ae´ronomie du CNRS December 2003. [1] A three-dimensional Monte Carlo model of Mercury's neutral sodium exosphere was used in the surface concentration of sodium along Mercury's motion around the Sun [Leblanc and Johnson, 2003]. Four

Johnson, Robert E.

333

Energy Savings Estimates of Light Emitting Diodes in Niche Lighting...  

Office of Environmental Management (EM)

in Niche Lighting Applications Prepared for: Building Technologies Program Office of Energy Efficiency and Renewable Energy U.S. Department of Energy Prepared by: Navigant...

334

Light modulating device  

DOE Patents [OSTI]

In a device for transmitting light, means for controlling the transmissivity of the device, including a ceramic, reversibly electrochromic, crystalline element having a highly reflective state when injected with electrons and charge compensating ions and a highly transmissive state when the electrons and ions are removed, the crystalline element being characterized as having a reflectivity of at least 50% in the reflective state and not greater than 10% in the transmissive state, and means for modulating the crystalline element between the reflective and transmissive states by injecting ions into the crystalline element in response to an applied electrical current of a first polarity and removing the ions in response to an applied electrical current of a second polarity.

Rauh, R. David (Newton, MA); Goldner, Ronald B. (Lexington, MA)

1989-01-01T23:59:59.000Z

335

Light modulating device  

DOE Patents [OSTI]

In a device for transmitting light, means for controlling the transmissivity of the device, including a ceramic, reversibly electrochromic, crystalline element having a highly reflective state when injected with electrons and charge compensating ions and a highly transmissive state when the electrons and ions are removed, the crystalline element being characterized as having a reflectivity of at least 50% in the reflective state and not greater than 10% in the transmissive state, and means for modulating the crystalline element between the reflective and transmissive states by injecting ions into the crystalline element in response to an applied electrical current of a first polarity and removing the ions in response to an applied electrical current of a second polarity are disclosed. 1 fig.

Rauh, R.D.; Goldner, R.B.

1989-12-26T23:59:59.000Z

336

Energy and lighting  

SciTech Connect (OSTI)

Advances in research for new types of lighting with increased efficacies (lumens/watt) are discussed in the following areas: (1) high-frequency, solid-state ballasts, (2) isotopic enhancement of mercury isotopes, (3) magnetic augmentation, (4) electrodeless, ultra-high frequency, (5) tuned phosphors, (6) two-photon phosphors, (7) heat mirrors, and (3) advanced control circuits to take advantage of daylight and occupancy. As of 1985, improvements in efficacy have been accomplished on an economic basis to save energy for (1) high-frequency ballasts (25%), (2) isotopic enhancement (5%), and (8) advanced control circuits (up to 50%). Most of these advances depend on a deeper understanding of the weakly ionized plasma as a radiating and diffusing medium. 3 figures, 4 tables.

Berman, S.

1985-01-01T23:59:59.000Z

337

Cost effective lighting  

SciTech Connect (OSTI)

Long-life replacement lamps for the incandescent lamp have been evaluated with regard to their cost effectiveness. The replacements include the use of energy buttons that extend lamp life as well as an adaptive fluorescent circline lamp that will fit into existing incandescent lamp sockets. The initial, operating, and replacement costs for one million lumen-hours are determined for each lamp system. We find the most important lighting cost component is the operating cost. Using lamps that are less efficient or devices that cause lamps to operate less efficiently are not cost-effective. The adaptive fluorescent circline lamp, even at an initial cost of $15.00, is the most cost effective source of illumination compared to the incandescent lamp and lamp systems examined. 3 refs., 6 tabs.

Morse, O.; Verderber, R.

1987-07-01T23:59:59.000Z

338

Posters | Posters --721 Exploring lighting cultures  

E-Print Network [OSTI]

Posters | Posters -- 721 Exploring lighting cultures Beyond light and emotions Vincent LAGANIER 1 , Jasmine van der POL 2 1. Lighting Applications Services (LiAS), Philips Lighting, France vincent.laganier@philips.com 2

Boyer, Edmond

339

Creative and Constructive Play with Light  

E-Print Network [OSTI]

children identify objects with these properties. Predict what materials light will pass through. Use paint and mixing light. Mixing paint creates a muddy brown or black. Mixing light creates white light

340

Analysis and methodology for measuring oxygen concentration in liquid sodium with a plugging meter  

SciTech Connect (OSTI)

Oxygen concentration in liquid sodium is a critical measurement in assessing the potential for corrosion damage in sodium-cooled fast reactors (SFRs). There has been little recent work on sodium reactors and oxygen detection. Thus, the technical expertise dealing with oxygen measurements within sodium is no longer readily available in the U.S. Two methods of oxygen detection that have been investigated are the plugging meter and the galvanic cell. One of the overall goals of the Univ. of Wisconsin's sodium research program is to develop an affordable, reliable galvanic cell oxygen sensor. Accordingly, attention must first be dedicated to a well-known standard known as a plugging meter. Therefore, a sodium loop has been constructed on campus in effort to develop the plugging meter technique and gain experience working with liquid metal. The loop contains both a galvanic cell test section and a plugging meter test section. Consistent plugging results have been achieved below 20 [wppm], and a detailed process for achieving effective plugging has been developed. This paper will focus both on an accurate methodology to obtain oxygen concentrations from a plugging meter, and on how to easily control the oxygen concentration of sodium in a test loop. Details of the design, materials, manufacturing, and operation will be presented. Data interpretation will also be discussed, since a modern discussion of plugging data interpretation does not currently exist. (authors)

Nollet, B. K.; Hvasta, M.; Anderson, M. [Univ. of Wisconsin-Madison, 1500 Engineering Dr., Madison, WI 53706 (United States)

2012-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "low-pressure sodium lighting" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Embodied Energy and Off-Grid Lighting  

E-Print Network [OSTI]

as a point of comparison with LED lighting product embodieda fairer comparison between off- grid LED lighting and other

Alstone, Peter

2012-01-01T23:59:59.000Z

342

Overcoming Common Pitfalls: Energy Efficient Lighting Projects...  

Broader source: Energy.gov (indexed) [DOE]

Overcoming Common Pitfalls: Energy Efficient Lighting Projects Overcoming Common Pitfalls: Energy Efficient Lighting Projects Transcript Presentation More Documents & Publications...

343

Automatic Mechetronic Wheel Light Device  

DOE Patents [OSTI]

A wheel lighting device for illuminating a wheel of a vehicle to increase safety and enhance aesthetics. The device produces the appearance of a "ring of light" on a vehicle's wheels as the vehicle moves. The "ring of light" can automatically change in color and/or brightness according to a vehicle's speed, acceleration, jerk, selection of transmission gears, and/or engine speed. The device provides auxiliary indicator lights by producing light in conjunction with a vehicle's turn signals, hazard lights, alarm systems, and etc. The device comprises a combination of mechanical and electronic components and can be placed on the outer or inner surface of a wheel or made integral to a wheel or wheel cover. The device can be configured for all vehicle types, and is electrically powered by a vehicle's electrical system and/or battery.

Khan, Mohammed John Fitzgerald (Silver Spring, MD)

2004-09-14T23:59:59.000Z

344

Environmental, health, and safety issues of sodium-sulfur batteries for electric and hybrid vehicles  

SciTech Connect (OSTI)

This report examines the shipping regulations that govern the shipment of dangerous goods. Since the elemental sodium contained in both sodium-sulfur and sodium-metal-chloride batteries is classified as a dangerous good, and is listed on both the national and international hazardous materials listings, both national and international regulatory processes are considered in this report The interrelationships as well as the differences between the two processes are highlighted. It is important to note that the transport regulatory processes examined in this report are reviewed within the context of assessing the necessary steps needed to provide for the domestic and international transport of sodium-beta batteries. The need for such an assessment was determined by the Shipping Sub-Working Group (SSWG) of the EV Battery Readiness Working Group (Working Group), created in 1990. The Working Group was created to examine the regulatory issues pertaining to in-vehicle safety, shipping, and recycling of sodium-sulfur batteries, each of which is addressed by a sub-working group. The mission of the SSWG is to establish basic provisions that will ensure the safe and efficient transport of sodium-beta batteries. To support that end, a proposal to the UN Committee of Experts was prepared by the SSWG, with the goal of obtaining a proper shipping name and UN number for sodium-beta batteries and to establish the basic transport requirements for such batteries (see the appendix for the proposal as submitted). It is emphasized that because batteries are large articles containing elemental sodium and, in some cases, sulfur, there is no existing UN entry under which they can be classified and for which modal transport requirements, such as the use of packaging appropriate for such large articles, are provided for. It is for this reason that a specific UN entry for sodium-beta batteries is considered essential.

Hammel, C.J.

1992-09-01T23:59:59.000Z

345

Far UV excitation of hydrogen and light emission; applications in astrophysics  

E-Print Network [OSTI]

Assuming a spherical symmetry, the extreme UV emitted by a very hot source ionizes low pressure molecular hydrogen making a transparent bubble of H II (Protons and electrons). For an increase of radius, intensity of extreme UV and temperature decrease, so that the plasma contains more and more atoms. A spherical shell, mainly of neutral atoms (H I) appears. If this shell is optically thick at Lyman frequencies of H I, it is superradiant and a competition of modes selects modes tangent to a sphere for which many atoms are excited. Thus, a shell of plasma emits, into a given direction, tangential rays showing a ring in which selected modes are brighter. While at Lyman frequencies, absorption of rays emitted by the source excites the atoms able to amplify the superradiance, a more powerful amplification of superradiance results from an induced scattering of the radial beams, which extends to feet of lines and progressively to the whole spectrum. Thermodynamics says that the brightness of radial and tangential beams tends to be equal; if the solid angle of observation is much larger for the ring than for the source, almost the whole light emitted by the source is transferred to the rings, and the source becomes invisible. Paradoxically, a glow due to incoherent scattering and impurities around the source remains visible. As the scattering decreases with the decrease of the radial intensity, the brightness of the ring decreases with radius. These characteristics are found in supernova remnant 1987A.

Jacques Moret-Bailly

2007-07-20T23:59:59.000Z

346

Utility lighting summit proves illuminating  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Utility-lighting-summit-proves-illuminating Sign In About | Careers | Contact | Investors | bpa.gov Search News & Us Expand News & Us Projects & Initiatives Expand Projects...

347

Photonic crystal light emitting diode.  

E-Print Network [OSTI]

?? This master's thesis describe electromagnetic simulations of a gallium antimonide (GaSb) light emitting diode, LED. A problem for such devices is that most of… (more)

Leirset, Erlend

2010-01-01T23:59:59.000Z

348

Linac Coherent Light Source Overview  

ScienceCinema (OSTI)

Take an animated tour of the Linac Coherent Light Source (LCLS). Follow the laser pulse from the injector gun all the way through to the Far Experimental Hall.

None

2013-05-29T23:59:59.000Z

349

Light Water Reactor Sustainability Newsletter  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

and nuclear waste disposal. Dr. Corradini has extensive research experience in the phenomenology of beyond design basis Meet the New LWRS Program Pathway Lead accidents in light...

350

LED Lighting Off the Grid  

Energy Savers [EERE]

D. & Kammen, D. M. Decentralized energy systems for clean electricity access. Nature Climate Change accepted, in press, (2015). Off-Grid Status Quo : Fuel Based Lighting...

351

Pedestrian-Friendly Nighttime Lighting  

Broader source: Energy.gov [DOE]

This November 19, 2013 webinar presented issues and considerations related to pedestrian-friendly nighttime lighting, such as color rendering, safety, and adaptation. When it comes to outdoor...

352

Light Water Reactor Sustainability Newsletter  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

hydraulics software RELAP-7 (which is under development in the Light Water Reactor Sustainability LWRS Program). A novel interaction between the probabilistic part (i.e., RAVEN)...

353

Light Water Reactor Sustainability Newsletter  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

30-35, August 2012. Clayton, D. A. and M. S. Hileman, 2012, Light Water Reactor Sustainability Non-Destructive Evaluation for Concrete Research and Development Roadmap, ORNLTM-...

354

Linac Coherent Light Source Overview  

Broader source: Energy.gov [DOE]

Take an animated tour of the Linac Coherent Light Source (LCLS). Follow the laser pulse from the injector gun all the way through to the Far Experimental Hall.

355

Lighting with Paint FABIO PELLACINI  

E-Print Network [OSTI]

Lighting with Paint FABIO PELLACINI Dartmouth College and FRANK BATTAGLIA, R. KEITH MORLEY, animation, rendering, optimization, painting ACM Reference Format: Pellacini, F., Battaglia, F., Morley, R

Pellacini, Fabio

356

Book review Light Scattering Reviews 4: Single Light Scattering and  

E-Print Network [OSTI]

-monograph on the use of space-time Green functions in the description of the diffusive radiation transport in active equation of the radiative transfer theory in the classical style of the ``Soviet'' school of radiativeBook review Light Scattering Reviews 4: Single Light Scattering and Radiative Transfer, A

357

EK101 Engineering Light Project: Evaluate Residential Lighting  

E-Print Network [OSTI]

for residential lighting (LED, Compact Fluorescent, Incandescent). Develop a plan of experiments to be conducted, CF, and Incandescent bulbs for the past ten years. (try the wayback time machine if other sources fail). Discuss the key challenges associated with a transition from incandescent lighting

Bifano, Thomas

358

Nittany Lights Landscape Lighting Sept. 28-30, 2012  

E-Print Network [OSTI]

Nittany Lights ­ Landscape Lighting Workshop Sept. 28-30, 2012 Penn State Campus - University Park with a lecture at the Palmer Art Museum to be provided by internationally known architectural/landscape artist get a chance to think beyond budgets, maintenance, codes, etc and get back to the fun creative side

359

Tolerance Test of Eisenia Fetida for Sodium Chloride  

SciTech Connect (OSTI)

Saltwater spills that make soil excessively saline often occur at petroleum exploration and production (E&P) sites and are ecologically damaging. Brine scars appear when produced water from an E&P site is spilled onto surrounding soil, causing loss of vegetation and subsequent soil erosion. Revegetating lands damaged by brine water can be difficult. The research reported here considers earthworms as a bioremedial treatment for increasing the salt mobility in this soil and encouraging plant growth and a healthy balance of soil nutrients. To determine the practical application of earthworms to remediate brine-contaminated soil, a 17-d test was conducted to establish salt tolerance levels for the common compost earthworm (Eisenia fetida) and relate those levels to soil salinity at brine-spill sites. Soil samples were amended with sodium chloride in concentrations ranging from 1 to 15 g/kg, which represent contamination levels at some spill sites. The survival rate of the earthworms was near 90% in all tested concentrations. Also, reproduction was noted in a number of the lower-concentration test replicates but absent above the 3-g/kg concentrations. Information gathered in this investigation can be used as reference in further studies of the tolerance of earthworms to salty soils, as results suggest that E. fetida is a good candidate to enhance remediation at brine-damaged sites.

Kerr, M.; Stewart, A.J.

2003-01-01T23:59:59.000Z

360

Sodium-bearing Waste Treatment Technology Evaluation Report  

SciTech Connect (OSTI)

Sodium-bearing waste (SBW) disposition is one of the U.S. Department of Energy (DOE) Idaho Operation Office’s (NE-ID) and State of Idaho’s top priorities at the Idaho National Engineering and Environmental Laboratory (INEEL). The INEEL has been working over the past several years to identify a treatment technology that meets NE-ID and regulatory treatment requirements, including consideration of stakeholder input. Many studies, including the High-Level Waste and Facilities Disposition Environmental Impact Statement (EIS), have resulted in the identification of five treatment alternatives that form a short list of perhaps the most appropriate technologies for the DOE to select from. The alternatives are (a) calcination with maximum achievable control technology (MACT) upgrade, (b) steam reforming, (c) cesium ion exchange (CsIX) with immobilization, (d) direct evaporation, and (e) vitrification. Each alternative has undergone some degree of applied technical development and preliminary process design over the past four years. This report presents a summary of the applied technology and process design activities performed through February 2004. The SBW issue and the five alternatives are described in Sections 2 and 3, respectively. Details of preliminary process design activities for three of the alternatives (steam reforming, CsIX, and direct evaporation) are presented in three appendices. A recent feasibility study provides the details for calcination. There have been no recent activities performed with regard to vitrification; that section summarizes and references previous work.

Charles M. Barnes; Arlin L. Olson; Dean D. Taylor

2004-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "low-pressure sodium lighting" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Demonstration Assessment of Light Emitting Diode (LED) Walkway Lighting at the Federal Aviation Administration William J. Hughes Technical Center, in Atlantic City, New Jersey  

SciTech Connect (OSTI)

This report documents the results of a collaborative project to demonstrate a solid state lighting (SSL) general illumination product in an outdoor area walkway application. In the project, six light-emitting diode (LED) luminaires were installed to replace six existing high pressure sodium (HPS) luminaires mounted on 14-foot poles on a set of exterior walkways and stairs at the Federal Aviation Administration (FAA) William J. Hughes Technical Center in Atlantic City, New Jersey, during December, 2007. The effort was a U.S. Department of Energy (DOE) SSL Technology Gateway Demonstration that involved a collaborative teaming agreement between DOE, FAA and Ruud Lighting (and their wholly owned division, Beta LED). Pre- and post-installation power and illumination measurements were taken and used in calculations of energy savings and related economic payback, while personnel impacted by the new lights were provided questionnaires to gauge their perceptions and feedback. The SSL product demonstrated energy savings of over 25% while maintaining illuminance levels and improving illuminance uniformity. PNNL's economic analysis yielded a variety of potential payback results depending on the assumptions used. In the best case, replacing HPS with the LED luminaire can yield a payback as low as 3 years. The new lamps were quite popular with the affected personnel, who gave the lighting an average score of 4.46 out of 5 for improvement.

Kinzey, Bruce R.; Myer, Michael

2008-03-18T23:59:59.000Z

362

Light-by-Light Scattering Effect in Light-Cone Supergraphs  

E-Print Network [OSTI]

We give a relatively simple explanation of the light-cone supergraph prediction for the UV properties of the maximally supersymmetric theories. It is based on the existence of a dynamical supersymmetry which is not manifest in the light-cone supergraphs. It suggests that N=4 supersymmetric Yang-Mills theory is UV finite and N=8 supergravity is UV finite at least until 7 loops whereas the $n$-point amplitudes have no UV divergences at least until $L=n+3$. Here we show that this prediction can be deduced from the properties of light-cone supergraphs analogous to the light-by-light scattering effect in QED. A technical aspect of the argument relies on the observation that the dynamical supersymmetry action is, in fact, a compensating field-dependent gauge transformation required for the retaining the light-cone gauge condition $A_+=0$.

Renata Kallosh; Pierre Ramond

2010-06-24T23:59:59.000Z

363

Process Flow Chart for Immobilizing of Radioactive High Concentration Sodium Hydroxide Product from the Sodium Processing Facility at the BN-350 Nuclear power plant in Aktau, Kazakhstan  

SciTech Connect (OSTI)

This paper describes the results of a joint research investigations carried out by the group of Kazakhstan, British and American specialists in development of a new material for immobilization of radioactive 35% sodium hydroxide solutions from the sodium coolant processing facility of the BN-350 nuclear power plant. The resulting solid matrix product, termed geo-cement stone, is capable of isolating long lived radionuclides from the environment. The physico-mechanical properties of geo-cement stone have been investigated and the flow chart for its production verified in a full scale experiments. (author)

Burkitbayev, M.; Omarova, K.; Tolebayev, T. [Ai-Farabi Kazakh National University, Chemical Faculty, Republic of Kazakhstan (Kazakhstan); Galkin, A. [KATEP Ltd., Republic of Kazakhstan (Kazakhstan); Bachilova, N. [NIISTROMPROEKT Ltd., Republic of Kazakhstan (Kazakhstan); Blynskiy, A. [Nuclear Technology Safety Centre, Republic of Kazakhstan (Kazakhstan); Maev, V. [MAEK-Kazatomprom Ltd., Republic of Kazakhstan (Kazakhstan); Wells, D. [NUKEM Limited- a member of the Freyssinet Group, Winfrith Technology Centre, Dorchester, Dorset (United Kingdom); Herrick, A. [NUKEM Limited- a member of the Freyssinet Group, Caithness (United Kingdom); Michelbacher, J. [Idaho National Laboratory, Idaho Falls (United States)

2008-07-01T23:59:59.000Z

364

Development of a model to predict flow oscillations in low-flow sodium boiling  

E-Print Network [OSTI]

An experimental and analytical program has been carried out in order to better understand the cause and effect of flow oscillations in boiling sodium systems. These oscillations have been noted in previous experiments with ...

Levin, Alan Edward

1980-01-01T23:59:59.000Z

365

EIS-0306: Treatment and Management of Sodium-Bonded Spent Nuclear Fuel  

Broader source: Energy.gov [DOE]

This EIS evaluates the potential environmental impacts of the proposed electrometallurgical treatment of DOE-owned sodium bonded spent nuclear fuel in the Fuel Conditioning Facility at Argonne...

366

Metal corrosion in a supercritical carbon dioxide - liquid sodium power cycle.  

SciTech Connect (OSTI)

A liquid sodium cooled fast reactor coupled to a supercritical carbon dioxide Brayton power cycle is a promising combination for the next generation nuclear power production process. For optimum efficiency, a microchannel heat exchanger, constructed by diffusion bonding, can be used for heat transfer from the liquid sodium reactor coolant to the supercritical carbon dioxide. In this work, we have reviewed the literature on corrosion of metals in liquid sodium and carbon dioxide. The main conclusions are (1) pure, dry CO{sub 2} is virtually inert but can be highly corrosive in the presence of even ppm concentrations of water, (2) carburization and decarburization are very significant mechanism for corrosion in liquid sodium especially at high temperature and the mechanism is not well understood, and (3) very little information could be located on corrosion of diffusion bonded metals. Significantly more research is needed in all of these areas.

Moore, Robert Charles; Conboy, Thomas M.

2012-02-01T23:59:59.000Z

367

An Evaluation of the Annular Fuel and Bottle-Shaped Fuel Concepts for Sodium Fast Reactors  

E-Print Network [OSTI]

Two innovative fuel concepts, the internally and externally cooled annular fuel and the bottle-shaped fuel, were investigated with the goal of increasing the power density and reduce the pressure drop in the sodium-cooled ...

Memmott, Matthew

368

Ultracold molecules from ultracold atoms : interactions in sodium and lithium gas  

E-Print Network [OSTI]

The thesis presents results from experiments in which ultracold Sodium-6 and Lithium-23 atomic gases were studied near a Feshbach resonance at high magnetic fields. The enhanced interactions between atoms in the presence ...

Christensen, Caleb A

2011-01-01T23:59:59.000Z

369

The Beta-Neutrino Correlation in Sodium-21 and Other Nuclei  

E-Print Network [OSTI]

RIA?INTproc?abetanu THE BETA-NEUTRINO CORRELATION IN SODIUM-electrons shaken off in beta decay. High detection ef?ciencyTOF template spectra for beta decays to 21 Ne + , are shown

Vetter, Paul A.; Abo-Shaeer, Jamil; Freedman, Stuart J.; Maruyama, Reina

2008-01-01T23:59:59.000Z

370

Application of the Technology Neutral Framework to Sodium-­Cooled Fast Reactors  

E-Print Network [OSTI]

Sodium cooled fast reactors (SFRs) are considered as a novel example to exercise the Technology Neutral Framework (TNF) proposed in NUREG-1860. One reason for considering SFRs is that they have historically had a licensing ...

Johnson, Brian C.

371

Applying risk informed methodologies to improve the economics of sodium-cooled fast reactors  

E-Print Network [OSTI]

In order to support the increasing demand for clean sustainable electricity production and for nuclear waste management, the Sodium-Cooled Fast Reactor (SFR) is being developed. The main drawback has been its high capital ...

Nitta, Christopher C

2010-01-01T23:59:59.000Z

372

Population strategies to decrease sodium intake : a global cost-effectiveness analysis  

E-Print Network [OSTI]

Excessive sodium consumption is both prevalent and very costly in many countries around the world. Recent research has found that more than 90% of the world's adult population live in countries with mean intakes exceeding ...

Webb, Michael William, S.M. Massachusetts Institute of Technology

2013-01-01T23:59:59.000Z

373

Application of the technology neutral framework to sodium cooled fast reactors  

E-Print Network [OSTI]

Sodium cooled fast reactors (SFRs) are considered as a novel example to exercise the Technology Neutral Framework (TNF) proposed in NUREG- 1860. One reason for considering SFRs is that they have historically had a licensing ...

Johnson, Brian C. (Brian Carl)

2010-01-01T23:59:59.000Z

374

Materials issues in high temperature ultrasonic transducers for under-sodium viewing  

SciTech Connect (OSTI)

Liquid sodium is used as the coolant in some fast spectrum nuclear reactors. This material is optically opaque. To facilitate operations and maintenance activities, an ultrasonic under-sodium viewing system has been developed. In the USA, the technology was successfully demonstrated in the 1970s and, over the intervening 30+ years, the capability was lost. This paper reports materials challenges encountered in developing both single-element and linear phased-array 2-MHz transducers that must operate at temperatures up to 260 deg. C. The critical issues are fundamentally material selection: the ability of a transducer to be immersed into liquid sodium and function at 260 deg. C, to achieve wetting and transmission of ultrasound into the sodium, and to be able to be removed and re-used.

Bond, L. J.; Griffin, J. W.; Posakony, G. J.; Harris, R. V.; Baldwin, D. L. [Pacific Northwest National Laboratory, Richland, WA 99354 (United States)

2012-05-17T23:59:59.000Z

375

Thermal-hydraulic analysis of innovative fuel configurations for the sodium fast reactor  

E-Print Network [OSTI]

The sodium fast reactor (SFR) is currently being reconsidered as an instrument for actinide management throughout the world, thanks in part to international programs such as the Generation-IV and especially the Global ...

Memmott, Matthew J

2009-01-01T23:59:59.000Z

376

Tools for supercritical carbon dioxide cycle analysis and the cycle's applicability to sodium fast reactors  

E-Print Network [OSTI]

The Sodium-Cooled Fast Reactor (SFR) and the Supercritical Carbon Dioxide (S-C0?) Recompression cycle are two technologies that have the potential to impact the power generation landscape of the future. In order for their ...

Ludington, Alexander R. (Alexander Rockwell)

2009-01-01T23:59:59.000Z

377

E-Print Network 3.0 - actual ineel sodium-bearing Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

for: actual ineel sodium-bearing Page: << < 1 2 3 4 5 > >> 1 RAC Report No. 4-CDC-Task Order 1-1999-Final FINAL REPORT Summary: Dose Reconstruction Study at the INEEL Centers for...

378

Sodium-Copper Exchange on Wyoming Montmorillonite in Chloride, Perchlorate, Nitrate, and Sulfate Solutions  

E-Print Network [OSTI]

Sodium-Copper Exchange on Wyoming Montmorillonite in Chloride, Perchlorate, Nitrate, and Sulfate. The copper exchange capacity (CuEC) and Na-Cu exchange reactions on Wyoming montmo- rillonite were studied

Sparks, Donald L.

379

The role of sodium bicarbonate in the nucleation of noctilucent clouds  

E-Print Network [OSTI]

for the sublimation of H2O to bulk ice. A 1-dimensional model of sodium chemistry was then employed to show and particles; cloud physics and chemistry; middle atmosphere ± composition and chemistry) Introduction

Boyer, Edmond

380

Lighting and Dark Sky Regulations  

E-Print Network [OSTI]

.........................................................................................................2 C. Cherokee County, Georgia's Outdoor Lighting and Road Glare Ordinance visited Apr. 0, 2008) (providing links to ordinances throughout the United States). 2 See, e.g. Cherokee Protection Ordinance (Dec. , 200). 5 See, e.g. Model Lighting Section for Zoning Ordinances and Cherokee

Rosemond, Amy Daum

Note: This page contains sample records for the topic "low-pressure sodium lighting" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Quantum Coherence in Photosynthetic Light  

E-Print Network [OSTI]

the following: How do light-harvesting systems deliver such high efficiency in the presence of disordered:333­61 First published online as a Review in Advance on December 13, 2011 The Annual Review of Condensed Matter quantum efficiency of photosynthetic light harvesting. Further, this speculation has led to much effort

Fleming, Graham R.

382

Light beam frequency comb generator  

DOE Patents [OSTI]

A light beam frequency comb generator uses an acousto-optic modulator to generate a plurality of light beams with frequencies which are uniformly separated and possess common noise and drift characteristics. A well collimated monochromatic input light beam is passed through this modulator to produce a set of both frequency shifted and unshifted optical beams. An optical system directs one or more frequency shifted beams along a path which is parallel to the path of the input light beam such that the frequency shifted beams are made incident on the modulator proximate to but separated from the point of incidence of the input light beam. After the beam is thus returned to and passed through the modulator repeatedly, a plurality of mutually parallel beams are generated which are frequency-shifted different numbers of times and possess common noise and drift characteristics.

Priatko, Gordon J. (Cupertino, CA); Kaskey, Jeffrey A. (Livermore, CA)

1992-01-01T23:59:59.000Z

383

Growth and bone development in weanling quarter horses fed diets supplemented with sodium zeolite-A  

E-Print Network [OSTI]

GROWTH AND BONE DEVELOPMENT IN WEANLING QUARTER HORSES FED DIETS SUPPLEMENTED WITH SODIUM ZEOLITE-A A Thesis by KIMBERLY SUZANNE FREY Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment... of the requirements for the degree of MASTER OF SCIENCE December 1991 Major Subject: Nutrition GROWTH AND BONE DEVELOPMENT IN WEANLING QUARTER HORSES FED DIETS SUPPLER WITH SODIUM ZEOLITE-A A Thesis by KIMBERLY SUZPZPK FREY Approved as to style and content by...

Frey, Kimberly Suzanne

1991-01-01T23:59:59.000Z

384

Sodium and potassium levels in the serum of acutely irradiated and non-irradiated rats  

E-Print Network [OSTI]

SODIUM AND POTASSIUM LEVELS IN THE SERUM OF ACUTELY IRRADIATED AND NON-IRRADIATED RATS A Thesis By DAVID PRESTON SHEPHERD Submitted to the Graduate College of the Texas ARM University in partial fulfillment of the requirements for the degree... of MASTER OF SCIENCE August 1967 Major Subject: Zoology SODIUM AND POTASSIUM LEVELS IN THE SERUM OF ACUTELY IRRADIATED AND NON-IRRADIATED RATS A Thesis By DAVID PRESTON SHEPHERD Approved as to style and content by: (Chairman of Committee) (Head...

Shepherd, David Preston

1967-01-01T23:59:59.000Z

385

Evolution of Sodium Technology R and D Actions Supporting French Liquid-Metal Fast Breeder Reactors  

SciTech Connect (OSTI)

This paper describes the evolution of sodium technology research and development in parallel to sodium-cooled fast breeder reactor (FBR) developments in France and provides information concerning operating plants and existing projects. This paper also discusses how supporting research has adapted to the decline in FBR activities since the decommissioning of Superphenix, while capitalizing on knowledge acquired over more than four decades to be passed down to future generations.

Rodriguez, G.; Baque, F.; Astegiano, J.C. [Commissariat a l'Energie Atomique, Cadarache (France)

2005-04-15T23:59:59.000Z

386

Characterization of the liquid sodium spray generated by a pipework hole  

SciTech Connect (OSTI)

Due to its advantageous thermodynamic characteristics at high temperature (550 deg. C), liquid sodium is the main candidate to be the cooling fluid for Generation TV nuclear reactors SFR (Sodium-cooled Fast Reactors). Now, sodium reacts very violently, both with the water and the oxygen of the air. Only few data were known about the liquid sodium behaviour when spread in the environment through micro defects. These are often present in a cooling circuit in welded or sealed joints and more rarely in the pipes. Micro defects, on the other hand, can be also generated in a cooling circuit because of the vibrations always present in a circuit into which a fluid runs. A new set-up, named LISOF, was built for testing high temperature liquid sodium when passing through micro defects and generating sprays or jets. Sprays and jets were generated by means of nozzles embedding sub milli-metric holes the diameter of which was: 0.2 mm, 0.4 mm, 0.5 mm. Tests were performed by pressurizing liquid sodium (550 deg. C) at: 3, 6 and 9 barg. Normal and high speed cinematography were used for the direct observation of the liquid sodium sprays while Phase Doppler Interferometry was used for the measurement of the droplets characteristics and velocity. Tests concerning the behaviour of the high temperature liquid sodium firing in air or in contact with the cement cover applied to a scaled down core catcher simulacrum were also performed. The paper presents the built set-up and the collected results. (authors)

Torsello, G.; Parozzi, F.; Nericcio, L. [RSE - Nuclear and Industrial Plant Safety Team, Power Generation System Dept., via Rubattino 54, 20134 Milano (Italy); Araneo, L.; Cozzi, F. [Politecnico di Milano, Energy Dept., via Lambruschini 4, 20156 Milano (Italy); Carcassi, M.; Mattei, N. [Universita di Pisa-Facolta d'Ingegneria DIMNP-Mechanical, Nuclear and Production Dep., Largo L. Lazzarino 2, 56126 Pisa (Italy)

2012-07-01T23:59:59.000Z

387

The tolerance of two varieties of cotton to relatively high levels of sodium and magnesium  

E-Print Network [OSTI]

THE TO'ERANCE OF TNO VARIETIES OF COTTON TO RELATIVELY HIGH LEVELS OF SODIUM AND MAGNESIUM A Tnesis by Msnhar C. Parekh Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirements for the degree...) (Nember) (Nemb ) August 1969 ABSTRACT The Tolerance of Two Varieties of Cotton to Relatively High Levels of Sodium and Magnesium. (August 1969) Masher C. Parekh, B. S. , Gujarat University, Directed by: Dr. H. E. Joham An experiment was conducted...

Parekh, Manhar C

2012-06-07T23:59:59.000Z

388

Solar-thermal Water Splitting Using the Sodium Manganese Oxide Process & Preliminary H2A Analysis  

SciTech Connect (OSTI)

There are three primary reactions in the sodium manganese oxide high temperature water splitting cycle. In the first reaction, Mn2O3 is decomposed to MnO at 1,500°C and 50 psig. This reaction occurs in a high temperature solar reactor and has a heat of reaction of 173,212 J/mol. Hydrogen is produced in the next step of this cycle. This step occurs at 700°C and 1 atm in the presence of sodium hydroxide. Finally, water is added in the hydrolysis step, which removes NaOH and regenerates the original reactant, Mn2O3. The high temperature solar�driven step for decomposing Mn2O3 to MnO can be carried out to high conversion without major complication in an inert environment. The second step to produce H2 in the presence of sodium hydroxide is also straightforward and can be completed. The third step, the low temperature step to recover the sodium hydroxide is the most difficult. The amount of energy required to essentially distill water to recover sodium hydroxide is prohibitive and too costly. Methods must be found for lower cost recovery. This report provides information on the use of ZnO as an additive to improve the recovery of sodium hydroxide.

Todd M. Francis, Paul R. Lichty, Christopher Perkins, Melinda Tucker, Peter B. Kreider, Hans H. Funke, Allan Lewandowski, and Alan W. Weimer

2012-10-24T23:59:59.000Z

389

Ion Recognition Approach to Volume Reduction of Alkaline Tank Waste by Separation of Sodium Salts  

SciTech Connect (OSTI)

The purpose of this research involving collaboration between Oak Ridge National Laboratory (ORNL) and Pacific Northwest National Laboratory (PNNL) is to explore new approaches to the separation of sodium hydroxide, sodium nitrate, and other sodium salts from high-level alkaline tank waste. The principal potential benefit is a major reduction in disposed waste volume, obviating the building of expensive new waste tanks and reducing the costs of vitrification. Principles of ion recognition are being researched toward discovery of liquid-liquid extraction systems that selectively separate sodium hydroxide and sodium nitrate from other waste components. The successful concept of pseudo hydroxide extraction using fluorinated alcohols and phenols is being developed at ORNL and PNNL toward a greater understanding of the controlling equilibria, role of solvation, and of synergistic effects involving crown ethers. Synthesis efforts are being directed toward enhanced sodium binding by crown ethers, both neutral and proton-ionizable. Studies with real tank waste at PNNL will provide feedback toward solvent compositions that have promising properties.

Moyer, Bruce A.; Bonnesen, Peter V.; Custelcean, Radu; Delmau, Laetitia H.; Engle, Nancy L.; Kang, Hyun-Ah; Keever, Tamara J.; Marchand, Alan P.; Gadthula, Srinivas; Gore, Vinayak K.; Huang, Zilin; Sivappa, Rasapalli; Tirunahari, Pavan K.; Levitskaia, Tatiana G.; Lumetta, Gregg J.

2005-09-26T23:59:59.000Z

390

An evaluation of neutralization for processing sodium-bearing liquid waste  

SciTech Connect (OSTI)

This report addresses an alternative concept for potentially managing the sodium-bearing liquid waste generated at the Idaho Chemical Processing Plant from the current method of calcining a blend of sodium waste and high-level liquid waste. The concept is based on removing the radioactive components from sodium-bearing waste by neutralization and grouting the resulting low-level waste for on-site near-surface disposal. Solidifying the sodium waste as a remote-handled transuranic waste is not considered to be practical because of excessive costs and inability to dispose of the waste in a timely fashion. Although neutralization can remove most radioactive components to provide feed for a solidified low-level waste, and can reduce liquid inventories four to nine years more rapidly than the current practice of blending sodium-bearing liquid waste with first-cycle raffinite, the alternative will require major new facilities and will generate large volumes of low-level waste. Additional facility and operating costs are estimated to be at least $500 million above the current practice of blending and calcining. On-site, low-level waste disposal may be technically difficult and conflict which national and state policies. Therefore, it is recommended that the current practice of calcining a blend of sodium-bearing liquid waste and high-level liquid waste be continued to minimize overall cost and process complexities. 17 refs., 4 figs., 16 tabs.

Chipman, N.A.; Engelgau, G.O.; Berreth, J.R.

1989-01-01T23:59:59.000Z

391

Impending U.S. lighting standards will boost market for halogen-infrared lamps: New product line expanding  

SciTech Connect (OSTI)

Many of the incandescent floodlights and spotlights manufactured today will not meet lighting efficiency standards taking effect in the US in 1995. As these models cease production, demand will grow for higher efficiency units to fill this huge market, which now totals about 100 million lamps per year. One prime contender is a new class of halogen lamps that use a spectrally selective coating to reflect heat back onto the filament, reducing the amount of electricity needed to generate light. GE Lighting`s Halogen-IR line is the only series of such lamps currently available to replace the conventional floodlights and spotlights that will be banned by the new standards. Other manufacturers may adopt the technology, however, and the Japanese producer Ushio already sells in the US a line of smaller halogen lamps with a similar heat-reflective coating. In terms of efficacy and lifetime, Halogen-IR lamps out perform standard incandescents and standard halogens, but fall far short of fluorescent, metal halide, and high-pressure sodium sources. These other lighting systems are more appropriate and cost-effective than incandescents for many ambient lighting applications. For accent lighting and other tasks that are best suited to incandescent lighting, however, the Halogen-IR lamp is often a superior choice.

Sardinsky, R.; Shepard, M.

1993-12-31T23:59:59.000Z

392

A Novel Low-Cost Sodium-Zinc Chloride Battery  

SciTech Connect (OSTI)

The sodium-metal halide (ZEBRA) battery has been considered as one of the most attractive energy storage systems for stationary and transportation applications. Even though Na-NiCl2 battery has been widely investigated, there is still a need to develop a more economical system to make this technology more attractive for commercialization. In the present work, a novel low-cost Na-ZnCl2 battery with a thin planar ??-Al2O3 solid electrolyte (BASE) was proposed, and its electrochemical reactions and battery performance were investigated. Compared to the Na-NiCl2 chemistry, the ZnCl2-based chemistry was more complicated, in which multiple electrochemical reactions including liquid-phase formation occurred at temperatures above 253°C. During the first stage of charge, NaCl reacted with Zn to form Na in the anode and Na2ZnCl4 in the cathode. Once all the residual NaCl was consumed, further charging led to the formation of a NaCl-ZnCl2 liquid phase. At the end of charge, the liquid phase reacted with Zn to produce solid ZnCl2. To identify the effects of liquid-phase formation on electrochemical performance, button cells were assembled and tested at 280°C and 240°C. At 280°C where the liquid phase formed during cycling, cells revealed quite stable cyclability. On the other hand, more rapid increase in polarization was observed at 240°C where only solid-state electrochemical reactions occurred. SEM analysis indicated that the stable performance at 280°C was due to the suppressed growth of Zn and NaCl particles, which were generated from the liquid phase during discharge of each cycle.

Lu, Xiaochuan; Li, Guosheng; Kim, Jin Yong; Lemmon, John P.; Sprenkle, Vincent L.; Yang, Zhenguo

2013-02-28T23:59:59.000Z

393

OLED lighting devices having multi element light extraction and luminescence conversion layer  

DOE Patents [OSTI]

An apparatus such as a light source has a multi element light extraction and luminescence conversion layer disposed over a transparent layer of the light source and on the exterior of said light source. The multi-element light extraction and luminescence conversion layer includes a plurality of light extraction elements and a plurality of luminescence conversion elements. The light extraction elements diffuses the light from the light source while luminescence conversion elements absorbs a first spectrum of light from said light source and emits a second spectrum of light.

Krummacher, Benjamin Claus (Regensburg, DE); Antoniadis, Homer (Mountain View, CA)

2010-11-16T23:59:59.000Z

394

Using QECBs for Street Lighting Upgrades: Lighting the Way to...  

Broader source: Energy.gov (indexed) [DOE]

Summarizes how the City of San Diego leveraged 13.1 million in qualified energy conservation bonds to increase the size of a street lighting upgrade project. Author: Lawrence...

395

Inorganic volumetric light source excited by ultraviolet light  

DOE Patents [OSTI]

The invention relates to a composition for the volumetric generation of radiation. The composition comprises a porous substrate loaded with a component capable of emitting radiation upon interaction with an exciting radiation. Preferably, the composition is an aerogel substrate loaded with a component, e.g., a phosphor, capable of interacting with exciting radiation of a first energy, e.g., ultraviolet light, to produce radiation of a second energy, e.g., visible light. 4 figures.

Reed, S.; Walko, R.J.; Ashley, C.S.; Brinker, C.J.

1994-04-26T23:59:59.000Z

396

Inorganic volumetric light source excited by ultraviolet light  

DOE Patents [OSTI]

The invention relates to a composition for the volumetric generation of radiation. The composition comprises a porous substrate loaded with a component capable of emitting radiation upon interaction with an exciting radiation. Preferably, the composition is an aerogel substrate loaded with a component, e.g., a phosphor, capable of interacting with exciting radiation of a first energy, e.g., ultraviolet light, to produce radiation of a second energy, e.g., visible light.

Reed, Scott (Albuquerue, NM); Walko, Robert J. (Albuquerue, NM); Ashley, Carol S. (Albuquerue, NM); Brinker, C. Jeffrey (Albuquerue, NM)

1994-01-01T23:59:59.000Z

397

Saturable absorption and 'slow light'  

E-Print Network [OSTI]

Quantitative evaluation of some recent 'slow light' experiments based on coherent population oscillations (CPO) shows that they can be more simply interpreted as saturable absorption phenomena. Therefore they do not provide an unambiguous demonstration of 'slow light'. Indeed a limiting condition on the spectral bandwidth is not generally satisfied, such that the requirements for burning a narrow spectral hole in the homogeneously broadened absorption line are not met. Some definitive tests of 'slow light' phenomena are suggested, derived from analysis of phase shift and pulse delay for a saturable absorber

Adrian C Selden

2006-03-25T23:59:59.000Z

398

Projection screen having reduced ambient light scattering  

DOE Patents [OSTI]

An apparatus and method for improving the contrast between incident projected light and ambient light reflected from a projection screen are described. The efficiency of the projection screen for reflection of the projected light remains high, while permitting the projection screen to be utilized in a brightly lighted room. Light power requirements from the projection system utilized may be reduced.

Sweatt, William C. (Albuquerque, NM)

2010-05-11T23:59:59.000Z

399

Residential Lighting: Title 24 and Technology Update  

E-Print Network [OSTI]

Residential Lighting: Title 24 and Technology Update Best practices in lighting design to comply;INTRODUCTION Course Topics Part 1: Technology Overview · Common lighting terminology · Residential lighting residential lighting regulation · Design examples to reach or exceed code Part 5: Compliance Process · Step

California at Davis, University of

400

Next Generation Light Source Workshops  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Next Generation Light Source Workshops A series of workshops will be held in late August with the goal of refining the scientific drivers for the facility and translating the...

Note: This page contains sample records for the topic "low-pressure sodium lighting" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Preparation of polyaniline/sodium alanate hybrid using a spray-drying process  

SciTech Connect (OSTI)

Nowadays, hydrogen is highly interesting as an energy source, in particular in the automotive field. In fact, hydrogen is attractive as a fuel because it prevents air pollution and greenhouse emissions. One of the main problems with the utilization of hydrogen as a fuel is its on-board storage. The purpouse of this work was to develop a new hybrid material consisting of a polyaniline matrix with sodium alanate (NaAlH{sub 4}) using a spray-drying process. The polyaniline used for this experiment was synthesized by following a well-established method for the synthesis of the emeraldine base form of polyaniline using dodecylbenzenesulfonic acid as dopant. Micro particles of polyaniline/sodium alanate hybrids with 30 and 50 wt% of sodium alanate were prepared by using a spray-drying technique. Dilute solutions of polyaniline/sodium alanate were first prepared, 10g of the solid materials were mixed with 350 ml of toluene under stirring at room temperature for 24h and the solutions were dried using spray-dryer (Büchi, Switzerland) with 115°C of an inlet temperature. The hybrids were analyzed by differential scanning calorimetry, FT-IR and scanning electron microscopy (SEM). The addition of sodium alanate decreased the glass transition temperature of the hybrids when compared to neat polyaniline. FT-IR spectrum analysis was performed to identify the bonding environment of the synthesized material and was observed that simply physically mixture occurred between polyaniline and sodium alanate. The SEM images of the hybrids showed the formation of microspheres with sodium alanate dispersed in the polymer matrix.

Moreira, B. R., E-mail: bru-rms@yahoo.com.br, E-mail: fabiopassador@gmail.com, E-mail: pessan@ufscar.br; Passador, F. R., E-mail: bru-rms@yahoo.com.br, E-mail: fabiopassador@gmail.com, E-mail: pessan@ufscar.br; Pessan, L. A., E-mail: bru-rms@yahoo.com.br, E-mail: fabiopassador@gmail.com, E-mail: pessan@ufscar.br [Dep. de Engenharia de Materiais, Federal University of São Carlos (Brazil)

2014-05-15T23:59:59.000Z

402

Ion Recognition Approach to Volume Reduction of Alkaline Tank Waste by Separation of Sodium Salts  

SciTech Connect (OSTI)

In this project, now completing its third year of its second renewal period, a collaborative project involving Oak Ridge National Laboratory, Pacific Northwest National Laboratory, and the University of North Texas has been addressing outstanding questions regarding the separation of the bulk sodium constituents of alkaline tank waste. The principal potential benefit of this research is a major reduction in the volume of radioactive tank waste, obviating the building of expensive new tanks and reducing the costs of vitrification. As a general approach, principles of ion recognition are being explored toward discovery and basic understanding of liquid-liquid extraction systems that selectively separate sodium hydroxide and sodium salts from waste-like matrices. Questions being addressed pertain to applicable extraction equilibria and how extraction properties relate to extractant structure. Progress has included the elucidation of the promising concept of pseudo hydroxide extraction (PHE), demonstration of crown-ether synergized PHE, demonstration of combined sodium hydroxide/sodium nitrate separation, and synthesis of novel ditopic receptors for ditopic PHE. In future efforts (pending renewal), a thermochemical study of PHE relating extractant acidity to extraction strength is proposed, and this study will be extended to systems containing crown ethers, including proton-ionizable ones. A series of crown ethers will be synthesized for this purpose and to investigate the extraction of bulk sodium salts (e.g., nitrate, nitrite, and sulfate), possibly in combination with sodium hydroxide. Simple proof-of-principle tests with real tank waste at PNNL will provide feedback toward solvent designs that have desirable properties. In view of the upcoming milestone of completion of the second renewal period, this report will, in addition to providing a summary of the past year's progress, summarize all of the work completed since the start of this project.

Moyer, Bruce A.; Marchand, Alan P.; Lumetta, Gregg J.

2004-06-30T23:59:59.000Z

403

Photonic-band-gap properties for two-component slow light  

SciTech Connect (OSTI)

We consider two-component ''spinor'' slow light in an ensemble of atoms coherently driven by two pairs of counterpropagating control laser fields in a double tripod-type linkage scheme. We derive an equation of motion for the spinor slow light (SSL) representing an effective Dirac equation for a massive particle with the mass determined by the two-photon detuning. By changing the detuning the atomic medium acts as a photonic crystal with a controllable band gap. If the frequency of the incident probe light lies within the band gap, the light experiences reflection from the sample and can tunnel through it. For frequencies outside the band gap, the transmission and reflection probabilities oscillate with the increasing length of the sample. In both cases the reflection takes place into the complementary mode of the probe field. We investigate the influence of the finite excited state lifetime on the transmission and reflection coefficients of the probe light. We discuss possible experimental implementations of the SSL using alkali-metal atoms such as rubidium or sodium.

Ruseckas, J.; Kudriasov, V.; Juzeliunas, G.; Unanyan, R. G.; Otterbach, J.; Fleischhauer, M. [Institute of Theoretical Physics and Astronomy, Vilnius University, A. Gostauto 12, Vilnius 01108 (Lithuania); Fachbereich Physik and Research Center OPTIMAS, Technische Universitaet Kaiserslautern, Kaiserslautern D-67663 (Germany)

2011-06-15T23:59:59.000Z

404

Flexible liquid core light guide with focusing and light shaping attachments  

DOE Patents [OSTI]

A liquid light guide system for ultraviolet light is disclosed that has a light shaping arrangement for the emitted light, a stable liquid core and sheath and reliable and effective end closures. 12 figs.

Kross, B.J.; Majewski, S.; Zorn, C.J.; Majewski, L.A.

1997-11-04T23:59:59.000Z

405

Office Lighting: Title 24 & Technology Update  

E-Print Network [OSTI]

Office Lighting: Title 24 & Technology Update Kelly Cunningham Outreach Director kcunning@ucdavis.edu California Lighting Technology Center, UC Davis RESEARCH . INNOVATION . PARTNERSHIP Supporting compliance apply the Title 24 Building Energy Efficiency Standards code requirements specific to lighting

California at Davis, University of

406

Embodied Energy and Off-Grid Lighting  

E-Print Network [OSTI]

Self-reported Impacts of LED Lighting Technology Comparedto Fuel-based Lighting on Night Market Business Prosperity28, no. 4, pp. 533-546. Lighting Africa (prepared by Dalberg

Alstone, Peter

2012-01-01T23:59:59.000Z

407

Beyond the Replacement Paradigm: Smart Lighting  

E-Print Network [OSTI]

Switches · Smart Building & Grid Interfaces · Efficient full spectrum LEDs without droop · Versatile, low - Visible Light Communications Integration of smart fixtures, networked sensors and control systemsBeyond the Replacement Paradigm: Smart Lighting Robert F. Karlicek, Jr. Director, Smart Lighting

Salama, Khaled

408

Lumental : web-based tunable lighting control  

E-Print Network [OSTI]

Dynamically adjusting the light spectrum of spectrum-tunable light fixtures promises significant energy savings over binary or incremental dimming control. To enable this level of controllability, lighting must evolve from ...

Hall, Harrison King

2012-01-01T23:59:59.000Z

409

Novel phosphors for solid state lighting  

E-Print Network [OSTI]

Solid state white light emitting diode lighting devices outperform conventional light sources in terms of lifetime, durability, and lumens per watt. However, the capital contribution is still to high to encourage widespread adoption. Furthermore...

Furman, Joshua D

2010-11-16T23:59:59.000Z

410

Lighting and GeometryLighting and Geometry Prof. Michael Misha Kazhdan  

E-Print Network [OSTI]

Lighting and GeometryLighting and Geometry Prof. Michael Misha Kazhdan misha· The viewer · The lights N Viewer · The lights · The geometry · The surface properties N L2 V Viewer L1Outline · Surface Properties (Review) · Lighting· Lighting · Geometry· Geometry #12;Surface Properties (Review

Fröhlich, Peter

411

Oscillating light wall above a sunspot light bridge  

E-Print Network [OSTI]

With the high tempo-spatial \\emph{Interface Region Imaging Spectrograph} 1330 {\\AA} images, we find that many bright structures are rooted in the light bridge of NOAA 12192, forming a \\emph{light wall}. The light wall is brighter than the surrounding areas, and the wall top is much brighter than the wall body. The New Vacuum Solar Telescope H$\\alpha$ and the \\emph{Solar Dynamics Observatory} 171 {\\AA} and 131 {\\AA} images are also used to study the light wall properties. In 1330 {\\AA}, 171 {\\AA}, and 131 {\\AA}, the top of the wall has a higher emission, while in the H$\\alpha$ line, the wall top emission is very low. The wall body corresponds to bright areas in 1330 {\\AA} and dark areas in the other lines. The top of the light wall moves upward and downward successively, performing oscillations in height. The deprojected mean height, amplitude, oscillation velocity, and the dominant period are determined to be 3.6 Mm, 0.9 Mm, 15.4 km s$^{-1}$, and 3.9 min, respectively. We interpret the oscillations of the lig...

Yang, Shuhong; Jiang, Fayu; Xiang, Yongyuan

2015-01-01T23:59:59.000Z

412

Science, Optics and You: Light and Colors  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

opticstutorialsindex.html INTRODUCTION LIGHT AND COLORS MODULE m4 SCIENCE, OPTICS & YOU GUIDEBOOK - 62 - SCIENCE, OPTICS & YOU GUIDEBOOK - 63 - m4: Light &...

413

Municipal Consortium LED Street Lighting Workshop Presentations...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Controls Norma Isahakian, City of Los Angeles Bureau of Street Lighting San Jose's "Smart" LED Streetlights: Controlled Amy Olay, City of San Jose Adaptive Lighting Controls...

414

Scientists produce transparent, light-harvesting material  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Transparent, light-harvesting material Scientists produce transparent, light-harvesting material The material could be used in development of transparent solar panels. November 3,...

415

LIGHT WATER REACTOR SUSTAINABILITY PROGRAM: INTRODUCTION  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

LIGHT WATER REACTOR SUSTAINABILITY PROGRAM: INTRODUCTION The Light Water Reactor Sustainability (LWRS) Program is the primary programmatic activity that addresses Objective 1...

416

OTEC- Commercial Lighting Retrofit Rebate Program  

Broader source: Energy.gov [DOE]

The Oregon Trail Electric Consumers Cooperative (OTEC) offers a commercial lighting retrofit program that provides rebates for commercial businesses that change existing lighting to more energy...

417

Combined Utilization of Cation Exchanger and Neutral Receptor to Volume Reduction of Alkaline Tank Waste by Separation of Sodium Salts  

SciTech Connect (OSTI)

In this report, novel approaches to the selective liquid-liquid extraction separation of sodium hydroxide and sodium nitrate from high-level alkaline tank waste will be discussed. Sodium hydroxide can be successfully separated from alkaline tank-waste supernatants by weakly acidic lipophilic hydroxy compounds via a cation-exchange mechanism referred to as pseudo hydroxide extraction. In a multi-cycle process, as sodium hydroxide in the aqueous phase becomes depleted, it is helpful to have a neutral sodium receptor in the extraction system to exploit the high nitrate concentration in the waste solution to promote sodium removal by an ion-pair extraction process. Simultaneous utilization of an ionizable organic hydroxy compound and a neutral extractant (crown ether) in an organic phase results in the synergistic enhancement of ion exchange and improved separation selectivity due to the receptor's strong and selective sodium binding. Moreover, combination of the hydroxy compound and the crown ether provides for mutually increased solubility, even in a non-polar organic solvent. Accordingly, application of Isopar{reg_sign} L, a kerosene-like alkane solvent, becomes feasible. This investigation involves examination of such dual-mechanism extraction phases for sodium extraction from simulated and actual salt cake waste solutions. Sodium salts can be regenerated upon the contact of the loaded extraction phases with water. Finally, conditions of potential extraction/strip cycling will be discussed.

Levitskaia, Tatiana G.; Lumetta, Gregg J.; Moyer, Bruce A.

2004-03-29T23:59:59.000Z

418

THE LUMINA PROJECT http://light.lbl.gov  

E-Print Network [OSTI]

components for the LED lights. #12;2 Introduction Solid-state lighting based on light emitting diode (LED

Jacobson, Arne

419

Types of Lighting in Commercial Buildings - Lighting Types  

Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) " ,"ClickPipelinesProved ReservesFeet)per Thousand28 198 18 Q 10 14.0 12.2 1.1 QPDF LightingLighting

420

LED Provides Effective and Efficient Parking Area Lighting at...  

Broader source: Energy.gov (indexed) [DOE]

White Light Options for Parking Area Lighting Demonstration Assessment of Light Emitting Diode (LED) Street Lighting, Final Report Guide to FEMP-Designated Parking Lot...

Note: This page contains sample records for the topic "low-pressure sodium lighting" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Demonstration Assessment of Light-Emitting Diode (LED) Freezer...  

Broader source: Energy.gov (indexed) [DOE]

Demonstration Assessment of Light-Emitting Diode (LED) Freezer Case Lighting Demonstration Assessment of Light-Emitting Diode (LED) Freezer Case Lighting This document is a report...

422

Demonstration Assessment of Light Emitting Diode (LED) Street...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Demonstration Assessment of Light Emitting Diode (LED) Street Lighting, Final Report Demonstration Assessment of Light Emitting Diode (LED) Street Lighting, Final Report This...

423

Demonstration Assessment of Light-Emitting Diode (LED) Roadway Lighting at the I-35W Bridge, Minneapolis, MN  

SciTech Connect (OSTI)

This report describes the process and results of a demonstration of solid-state lighting (SSL) technology conducted in 2009 at the recently reconstructed I-35W bridge in Minneapolis, MN. The project was supported under the U.S. Department of Energy (DOE) Solid-State Lighting GATEWAY Technology Demonstration Program. Other participants in the demonstration project included the Minnesota Department of Transportation (Mn/DOT), Federal Highways Administration (FHWA), and BetaLED™ (a division of Ruud Lighting). Pacific Northwest National Laboratory (PNNL) conducted the measurements and analysis of the results. DOE has implemented a three-year evaluation of the LED luminaires in this installation in order to develop new longitudinal field data on LED performance in a challenging, real-world environment. This document provides information through the initial phase of the I-35W bridge project, up to and including the opening of the bridge to the public and the initial feedback received on the LED lighting installation from bridge users. Initial findings of the evaluation are favorable, with minimum energy savings level of 13% for the LED installation relative to the simulated base case using 250W high-pressure sodium (HPS) fixtures. The LEDs had an average illuminance level of 0.91 foot candles compared to 1.29 fc for the HPS lamps. The LED luminaires cost $38,000 more than HPS lamps, yielding a lengthy payback period, however the bridge contractor had offered to include the LED luminaires as part of the construction package at no additional cost. One potentially significant benefit of the LEDs in this installation is avoiding rolling lane closures on the heavily-traveled interstate bridge for the purpose of relamping the HPS fixtures. Rolling lane closures involve multiple crew members and various maintenance and safety vehicles, diversion of traffic, as well as related administrative tasks (e.g., approvals, scheduling, etc.). Mn/DOT records show an average cost of relamping fixtures along interstate roadways of between $130-150 per pole. The previous bridge saw a lamp mortality rate of approximately 50% every two years, though the new bridge was designed to minimize many of the vibration issues. A voluntary Web-based feedback survey of nearly 500 self-described bridge users showed strong preference for the LED lighting - positive comments outnumbered negative ones by about five-to-one.

Kinzey, Bruce R.; Myer, Michael

2009-08-31T23:59:59.000Z

424

Two-dimensional computational modeling of sodium boiling in simulated LMFBR fuel-pin bundles  

SciTech Connect (OSTI)

Extensive sodium boiling tests have been carried out in two simulated LMFBR fuel pin bundles in the Thermal-Hydraulic Out-of-Reactor Safety (THORS) Facility at Oak Ridge National Laboratory. Experimental results from a 19-pin bundle (THORS Bundle 6A) have been previously reported, and experimental results from a 61-pin bundle (THORS Bundle 9) will be reported soon. The results discussed here are from the 19-pin bundle. Preliminary analysis has shown that the computational methods used and conclusions reached are equally valid for the 61-pin bundle, as well as the 19-pin in-reactor Sodium Loop Safety Facility (SLSF) W-1 experiment. The main result of THORS sodium boiling experimentation is that boiling behavior is determined by two-dimensional effects, i.e., the rates of mass, momentum and energy transfer in the direction perpendicular to the axes of the fuel pins.

Dearing, J.F.

1981-01-01T23:59:59.000Z

425

Development and application of modeling tools for sodium fast reactor inspection  

SciTech Connect (OSTI)

To support the development of in-service inspection methods for the Advanced Sodium Test Reactor for Industrial Demonstration (ASTRID) project led by the French Atomic Energy Commission (CEA), several tools that allow situations specific to Sodium cooled Fast Reactors (SFR) to be modeled have been implemented in the CIVA software and exploited. This paper details specific applications and results obtained. For instance, a new specular reflection model allows the calculation of complex echoes from scattering structures inside the reactor vessel. EMAT transducer simulation models have been implemented to develop new transducers for sodium visualization and imaging. Guided wave analysis tools have been developed to permit defect detection in the vessel shell. Application examples and comparisons with experimental data are presented.

Le Bourdais, Florian; Marchand, Benoît; Baronian, Vahan [CEA LIST, Centre de Saclay F-91191 Gif-sur-Yvette (France)

2014-02-18T23:59:59.000Z

426

Hemodynamic characterization of chronic bile duct-ligated rats: effect of pentobarbital sodium  

SciTech Connect (OSTI)

Systemic and splanchnic hemodynamics of the chronic bile duct-ligated rat were characterized by radioactive microspheres. Conscious and pentobarbital sodium-anesthetized, bile duct-ligated and sham-operated rats had cardiac output and regional organ blood flows determined. The conscious bile duct-ligated rat compared with the sham-operated showed a hyperdynamic circulation with an increased cardiac output and portal tributary blood flow. Pentobarbital sodium anesthesia induced marked hemodynamic changes in both sham-operated and bile duct-ligated rats. The latter group was especially sensitive to its effects; thus, comparison of cardiac output and portal tributary blood flow between anesthetized bile duct-ligated and sham-operated rats showed no significant differences. The authors conclude that the rat with cirrhosis due to chronic bile duct ligation is an excellent model for hemodynamic investigations but should be studied in the conscious state, since pentobarbital sodium anesthesia eliminated the hyperdynamic circulation.

Lee, S.S.; Girod, C.; Braillon, A.; Hadengue, A.; Lebrec, D.

1986-08-01T23:59:59.000Z

427

GIF sodium fast reactor project R and D on safety and operation  

SciTech Connect (OSTI)

The 'Safety and Operation' project is started in 2009 within the framework of Generation-IV International Forum (GIF) Sodium Fast Reactor (SFR) research and development program. In the safety area, the project involves R and D activities on phenomenological model development and experimental programs, conceptual studies in support of the design of safety provisions, preliminary assessment of safety systems, framework and methods for analysis of safety architecture. In the operation area, the project involves R and D activities on fast reactors safety tests and analysis of reactor operations, feedback from decommissioning, in-service inspection technique development, under-sodium viewing and sodium chemistry. This paper presents a summary of such activities and the main achievements. (authors)

Vasile, A.; Sofu, T.; Jeong, H. Y.; Sakai, T. [CEA DEN Cadarache, DER, 13108 Saint-Paul-Lez-Durance (France)

2012-07-01T23:59:59.000Z

428

Design and development of a high-temperature sodium compatibility testing facility  

SciTech Connect (OSTI)

The use of advanced alloys within sodium-cooled fast reactors (SFRs) has been identified as a means of increasing plant efficiency and reducing construction costs. In particular, alloys such as NF-616, NF-709 and HT-UPS are promising because they exhibit greater strength than traditional structural materials such as 316-SS. However, almost nothing is known about the sodium compatibility of these new alloys. Therefore, research taking place at the Univ. of Wisconsin-Madison is focused on studying the effects of sodium corrosion on these materials under prototypic SFR operating conditions (600 [ deg. C], V Na=10 [m/s], C 0{approx} 1 [wppm]). This paper focuses on the design and construction of the testing facility with an emphasis on moving magnet pumps (MMPs). Corrosion data from a preliminary 500 [hr] natural convection test will also be presented. (authors)

Hvasta, M. G.; Nolet, B. K.; Anderson, M. H. [Univ. of Wisconsin-Madison, 1500 Engineering Dr., Madison - ERB 841, WI 53705 (United States)

2012-07-01T23:59:59.000Z

429

Electromagnetic reactions on light nuclei  

E-Print Network [OSTI]

Electromagnetic reactions on light nuclei are fundamental to advance our understanding of nuclear structure and dynamics. The perturbative nature of the electromagnetic probes allows to clearly connect measured cross sections with the calculated structure properties of nuclear targets. We present an overview on recent theoretical ab-initio calculations of electron-scattering and photonuclear reactions involving light nuclei. We encompass both the conventional approach and the novel theoretical framework provided by chiral effective field theories. Because both strong and electromagnetic interactions are involved in the processes under study, comparison with available experimental data provides stringent constraints on both many-body nuclear Hamiltonians and electromagnetic currents. We discuss what we have learned from studies on electromagnetic observables of light nuclei, starting from the deuteron and reaching up to nuclear systems with mass number A=16.

Sonia Bacca; Saori Pastore

2014-07-13T23:59:59.000Z

430

Enrichment of light hydrocarbon mixture  

SciTech Connect (OSTI)

Light hydrocarbon enrichment is accomplished using a vertically oriented distillation column having a plurality of vertically oriented, nonselective micro/mesoporous hollow fibers. Vapor having, for example, both propylene and propane is sent upward through the distillation column in between the hollow fibers. Vapor exits neat the top of the column and is condensed to form a liquid phase that is directed back downward through the lumen of the hollow fibers. As vapor continues to ascend and liquid continues to countercurrently descend, the liquid at the bottom of the column becomes enriched in a higher boiling point, light hydrocarbon (propane, for example) and the vapor at the top becomes enriched in a lower boiling point light hydrocarbon (propylene, for example). The hollow fiber becomes wetted with liquid during the process.

Yang; Dali (Los Alamos, NM); Devlin, David (Santa Fe, NM); Barbero, Robert S. (Santa Cruz, NM); Carrera, Martin E. (Naperville, IL); Colling, Craig W. (Warrenville, IL)

2010-08-10T23:59:59.000Z

431

Enrichment of light hydrocarbon mixture  

DOE Patents [OSTI]

Light hydrocarbon enrichment is accomplished using a vertically oriented distillation column having a plurality of vertically oriented, nonselective micro/mesoporous hollow fibers. Vapor having, for example, both propylene and propane is sent upward through the distillation column in between the hollow fibers. Vapor exits neat the top of the column and is condensed to form a liquid phase that is directed back downward through the lumen of the hollow fibers. As vapor continues to ascend and liquid continues to countercurrently descend, the liquid at the bottom of the column becomes enriched in a higher boiling point, light hydrocarbon (propane, for example) and the vapor at the top becomes enriched in a lower boiling point light hydrocarbon (propylene, for example). The hollow fiber becomes wetted with liquid during the process.

Yang, Dali (Los Alamos, NM); Devlin, David (Santa Fe, NM); Barbero, Robert S. (Santa Cruz, NM); Carrera, Martin E. (Naperville, IL); Colling, Craig W. (Warrenville, IL)

2011-11-29T23:59:59.000Z

432

Draft Environmental Impact Statement for the Treatment and Management of Sodium-Bonded Spent Nuclear Fuel  

SciTech Connect (OSTI)

This document summarizes the U.S. Department of Energy's ''Draft Environmental Impact Statement for the Treatment and Management of Sodium-Bonded Spent Nuclear Fuel''. In addition to information concerning the background, purpose and need for the proposed action, and the National Environmental Policy Act process, this summary describes the characteristics of sodium-bonded spent nuclear fuel, the proposed treatment methods, the proposed facilities, the alternatives considered, and the environmental consequences of these alternatives. A glossary is included at the end to assist the reader with some of the technical terms used in this document.

N /A

1999-07-30T23:59:59.000Z

433

Galvanic corrosion of structural aluminum coupled with mild steel in a dilute sodium dichromate electrolyte  

E-Print Network [OSTI]

GALVANIC COP?'SION OF STRUCTURAL ALI'I'lINUl'I COUPLED WITH MILD STEEL IN A OILLrl'E SODIUM DICHPOliATE FLECTROLY'I E A Tl. esi, ROBERT FRANKLIN FORD, JR. Submitted to the Graduate Co11ege of Texas AEM University in Partia1 fuifiilment.... Approved as to style and content by: + ~J Co-Chairman of Commii:t C Co-Chair n of Committe~e Member+ I Head of D=p rtm t) Januar; IDIO ABSTRACT Calvanic Corrosion of Structural Aluminum Coup'led with Mild Steel in a Dilute Sodium Dichromate...

Ford, Robert Franklin

1970-01-01T23:59:59.000Z

434

Method of making a current collector for a sodium/sulfur battery  

DOE Patents [OSTI]

This specification is directed to a method of making a current collector for a sodium/sulfur battery. The current collector so-made is electronically conductive and resistant to corrosive attack by sulfur/polysulfide melts. The method includes the step of forming the current collector for the sodium/sulfur battery from a composite material formed of aluminum filled with electronically conductive fibers selected from the group of fibers consisting essentially of graphite fibers having a diameter up to 10 microns and silicon carbide fibers having a diameter in a range of 500--1,000 angstroms. 2 figs.

Tischer, R.P.; Winterbottom, W.L.; Wroblowa, H.S.

1987-03-10T23:59:59.000Z

435

Method of making a current collector for a sodium/sulfur battery  

DOE Patents [OSTI]

This specification is directed to a method of making a current collector (14) for a sodium/sulfur battery (10). The current collector so-made is electronically conductive and resistant to corrosive attack by sulfur/polysulfide melts. The method includes the step of forming the current collector for the sodium/sulfur battery from a composite material (16) formed of aluminum filled with electronically conductive fibers selected from the group of fibers consisting essentially of graphite fibers having a diameter up to 10 microns and silicon carbide fibers having a diameter in a range of 500-1000 angstroms.

Tischer, Ragnar P. (Birmingham, MI); Winterbottom, Walter L. (Farmington Hills, MI); Wroblowa, Halina S. (West Bloomfield, MI)

1987-01-01T23:59:59.000Z

436

Preliminary analysis of patent trends for sodium/sulfur battery technology  

SciTech Connect (OSTI)

This document summarizes development trends in sodium/sulfur battery technology based on data from US patents. Purpose of the study was to use the activity, timing and ownership of 285 US patents to identify and describe broad patterns of change in sodium/sulfur battery technology. The analysis was conducted using newly developed statistical and computer graphic techniques for describing technology development trends from patent data. This analysis suggests that for some technologies trends in patent data provide useful information for public and private R and D planning.

Triplett, M.B.; Winter, C.; Ashton, W.B.

1985-07-01T23:59:59.000Z

437

Monitored lighting energy savings from dimmable lighting controls in  

E-Print Network [OSTI]

, product, or process disclosed, or represents that its use would not infringe privately owned rights. Reference herein to any specific commercial product, process, or service by its trade name, trademark 94720, USA Abstract Digital addressable, dimmable lighting controls were introduced to the US market

438

National Synchrotron Light Source Activity Report 1998  

SciTech Connect (OSTI)

National Synchrotron Light Source Activity Report for period October 1, 1997 through September 30, 1998

Rothman, Eva

1999-05-01T23:59:59.000Z

439

National Synchrotron Light Source annual report 1991  

SciTech Connect (OSTI)

This report contains abstracts from research conducted at the national synchrotron light source. (LSP)

Hulbert, S.L.; Lazarz, N.N. (eds.)

1992-04-01T23:59:59.000Z

440

Organic electroluminescent devices having improved light extraction  

DOE Patents [OSTI]

Organic electroluminescent devices having improved light extraction include a light-scattering medium disposed adjacent thereto. The light-scattering medium has a light scattering anisotropy parameter g in the range from greater than zero to about 0.99, and a scatterance parameter S less than about 0.22 or greater than about 3.

Shiang, Joseph John (Niskayuna, NY)

2007-07-17T23:59:59.000Z

Note: This page contains sample records for the topic "low-pressure sodium lighting" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Demand Responsive Lighting: A Scoping Study  

E-Print Network [OSTI]

9: Lighting Energy Usage for Commercial Building Lighting incommercial buildings. 4.2. Energy The California Energy Commission has analyzed lighting energy usageCommercial Sector on 2003 Peak Day [Source: CEC 2003 Data] Figure 9: Lighting Energy Usage for Commercial Building

Rubinstein, Francis; Kiliccote, Sila

2007-01-01T23:59:59.000Z

442

Nonimaging light concentrator with uniform irradiance  

DOE Patents [OSTI]

A nonimaging light concentrator system including a primary collector of light, an optical mixer disposed near the focal zone for collecting light from the primary collector, the optical mixer having a transparent entrance aperture, an internally reflective housing for substantially total internal reflection of light, a transparent exit aperture and an array of photovoltaic cells disposed near the transparent exit aperture.

Winston, Roland (Chicago, IL); Gee, Randy C. (Arvada, CO)

2003-04-01T23:59:59.000Z

443

Light modulated switches and radio frequency emitters  

DOE Patents [OSTI]

The disclosure relates to a light modulated electron beam driven radiofrequency emitter. Pulses of light impinge on a photoemissive device which generates an electron beam having the pulse characteristics of the light. The electron beam is accelerated through a radiofrequency resonator which produces radiofrequency emission in accordance with the electron, hence, the light pulses.

Wilson, Mahlon T. (Los Alamos, NM); Tallerico, Paul J. (Los Alamos, NM)

1982-01-01T23:59:59.000Z

444

Highly Efficient Silicon Light Emitting Diode  

E-Print Network [OSTI]

silicon light-emitting diodes (LED) that efficiently emit photons with energy around the silicon bandgap

Leminh Holleman Wallinga; P. Leminh; J. Holleman; H. Wallinga

2000-01-01T23:59:59.000Z

445

Today LED Holiday Lights, Tomorrow the World?  

SciTech Connect (OSTI)

This article for The APEM Advantage, the quarterly newsletter of the Association of Professional Energy Managers (APEM) describes the recent increase in the popularity of light emitting diode (LED) lighting and compares LED light output with that of incandescent and compact fluorescent lighting.

Gordon, Kelly L.

2004-12-20T23:59:59.000Z

446

Damage tolerant light absorbing material  

DOE Patents [OSTI]

A light absorbing article comprised of a composite of carbon-bonded carbon fibers, is prepared by: blending carbon fibers with a carbonizable organic powder to form a mixture; dispersing the mixture into an aqueous slurry; vacuum molding the aqueous slurry to form a green article; drying and curing the green article to form a cured article; and, carbonizing the cured article at a temperature of at least about 1000 C to form a carbon-bonded carbon fiber light absorbing composite article having a bulk density less than 1 g/cm[sup 3]. 9 figures.

Lauf, R.J.; Hamby, C. Jr.; Akerman, M.A.; Seals, R.D.

1993-09-07T23:59:59.000Z

447

Solid state electrochromic light modulator  

DOE Patents [OSTI]

An all solid-state variable transmission electrochromic device has a source of charge compensating ions. An inorganic oxide counterelectrode film which on reduction with the accompanying insertion of the charge compensating ions increases its transmission of light of predetermined wavelength is separated from a primary electrochromic film which on reduction with the accompanying insertion of the charge compensating ions decreases its transmission of light of predetermined wavelength by an insulating electrolyte film that transports the charge compensating ions. First and second electrodes are contiguous with the inorganic oxide counter electrode film and the primary electrochromic film, respectively, and separated by the three films.

Cogan, Stuart F. (111 Downey St., Norwood, MA 02062); Rauh, R. David (111 Downey St., Norwood, MA 02062)

1990-01-01T23:59:59.000Z

448

Solid state electrochromic light modulator  

DOE Patents [OSTI]

An all solid-state variable transmission electrochromic device has a source of charge compensating ions. An inorganic oxide counterelectrode film which on reduction with the accompanying insertion of the charge compensating ions increases its transmission of light of predetermined wavelength is separated from a primary electrochromic film which on reduction with the accompanying insertion of the charge compensating ions decreases its transmission of light of predetermined wavelength by an insulating electrolyte film that transports the charge compensating ions. First and second electrodes are contiguous with the inorganic oxide counter electrode film and the primary electrochromic film, respectively, and separated by the three films.

Cogan, Stuart F. (Sudbury, MA); Rauh, R. David (Newton, MA)

1993-01-01T23:59:59.000Z

449

Solid state electrochromic light modulator  

DOE Patents [OSTI]

An all solid-state variable transmission electrochromic device has a source of charge compensating ions. An inorganic oxide counter electrode film which on reduction with the accompanying insertion of the charge compensating ions increases its transmission of light of predetermined wavelength is separated from a primary electrochromic film which on reduction with the accompanying insertion of the charge compensating ions decreases its transmission of light of predetermined wavelength by an insulating electrolyte film that transports the charge compensating ions. First and second electrodes are contiguous with the inorganic oxide counter electrode film and the primary electrochromic film, respectively, and separated by the three films. 4 figs.

Cogan, S.F.; Rauh, R.D.

1990-07-03T23:59:59.000Z

450

Damage tolerant light absorbing material  

DOE Patents [OSTI]

A light absorbing article comprised of a composite of carbon-bonded carbon fibers, prepared by: blending carbon fibers with a carbonizable organic powder to form a mixture; dispersing the mixture into an aqueous slurry; vacuum molding the aqueous slurry to form a green article; drying and curing the green article to form a cured article; and, carbonizing the cured article at a temperature of at least about 1000.degree. C. to form a carbon-bonded carbon fiber light absorbing composite article having a bulk density less than 1 g/cm.sup.3.

Lauf, Robert J. (Oak Ridge, TN); Hamby, Jr., Clyde (Harriman, TN); Akerman, M. Alfred (Knoxville, TN); Seals, Roland D. (Oak Ridge, TN)

1993-01-01T23:59:59.000Z

451

Fluorescent Lighting | Department of Energy  

Office of Environmental Management (EM)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "of Energy Power.pdf Flash2006-14.pdfattachment.pdf6.pdf5.pdfFluorescent Lighting Fluorescent Lighting

452

Simplified modeling of liquid sodium medium with temperature and velocity gradient using real thermal-hydraulic data. Application to ultrasonic thermometry in sodium fast reactor  

SciTech Connect (OSTI)

In the framework of the French R and D program for the Generation IV reactors and specifically for the sodium cooled fast reactors (SFR), studies are carried out on innovative instrumentation methods in order to improve safety and to simplify the monitoring of fundamental physical parameters during reactor operation. The aim of the present work is to develop an acoustic thermometry method to follow up the sodium temperature at the outlet of subassemblies. The medium is a turbulent flow of liquid sodium at 550 Degree-Sign C with temperature inhomogeneities. To understand the effect of disturbance created by this medium, numerical simulations are proposed. A ray tracing code has been developed with Matlab Copyright-Sign in order to predict acoustic paths in this medium. This complex medium is accurately described by thermal-hydraulic data which are issued from a simulation of a real experiment in Japan. The analysis of these results allows understanding the effects of medium inhomogeneities on the further thermometric acoustic measurement.

Massacret, N.; Jeannot, J. P. [DEN/DTN/STPA/LIET, CEA Cadarache, Saint Paul Lez Durance (France); Moysan, J.; Ploix, M. A.; Corneloup, G. [Aix-Marseille Univ, LMA UPR 7051 CNRS, site LCND, 13625 Aix-en-Provence (France)

2013-01-25T23:59:59.000Z

453

Illuminating system and method for specialized and decorative lighting using liquid light guides  

DOE Patents [OSTI]

The present invention comprises an illumination system for specialized decorative lighting including a light source, a flexible plastic tube sheath for distributing the light to a remote location, a transparent liquid core filling the tube that has an index of refraction greater than that of the plastic tube and an arrangement where light coupled from the light source is caused to leak from the liquid light guide at desired locations for the purposes of specialized lighting, such as underwater illumination in swimming pools.

Zorn, Carl J. (Yorktown, VA); Kross, Brian J. (Yorktown, VA); Majewski, Stanislaw (Grafton, VA); Wojcik, Randolph F. (Yorktown, VA)

1998-01-01T23:59:59.000Z

454

Strategy Guideline: High Performance Residential Lighting  

SciTech Connect (OSTI)

The Strategy Guideline: High Performance Residential Lighting has been developed to provide a tool for the understanding and application of high performance lighting in the home. The high performance lighting strategies featured in this guide are drawn from recent advances in commercial lighting for application to typical spaces found in residential buildings. This guide offers strategies to greatly reduce lighting energy use through the application of high quality fluorescent and light emitting diode (LED) technologies. It is important to note that these strategies not only save energy in the home but also serve to satisfy the homeowner's expectations for high quality lighting.

Holton, J.

2012-02-01T23:59:59.000Z

455

Light-induced disassembly of dusty bodies in inner protoplanetary discs: implications for the formation of planets  

E-Print Network [OSTI]

Laboratory experiments show that a solid-state greenhouse effect in combination with thermophoresis can efficiently erode a dust bed in a low-pressure gaseous environment. The surface of an illuminated, light absorbing dusty body is cooler than the dust below the surface (solidstate greenhouse effect). This temperature gradient leads to a directed momentum transfer between gas and dust particles and the dust particles are subject to a force towards the surface(thermophoresis). If the thermophoretic force is stronger than gravity and cohesion, dust particles are ejected. Applied to protoplanetary discs, dusty bodies smaller than several kilometres in size which are closer to a star than about 0.4 au are subject to a rapid and complete disassembly to submillimetre size dust aggregates by this process. While an inward-drifting dusty body is destroyed, the generated dust is not lost for the disc by sublimation or subsequent accretion on to the star but can be reprocessed by photophoresis or radiation pressure. Pl...

Wurm, Gerhard

2007-01-01T23:59:59.000Z

456

Sodium Cooled Fast Reactors and the Pyro-Process: Conversion of Nuclear Waste into a Fuel Source  

E-Print Network [OSTI]

1 Sodium Cooled Fast Reactors and the Pyro-Process: Conversion of Nuclear Waste into a Fuel Source. Belanger Chair, Department of Physics #12;2 Abstract A review of the sodium cooled fast reactor........................................................................................23 1.3.5 Reactor Startup

Belanger, David P.

457

Structure and hydrogen dynamics of pure and Ti-doped sodium alanate Jorge iguez,1,2  

E-Print Network [OSTI]

Structure and hydrogen dynamics of pure and Ti-doped sodium alanate Jorge Íñiguez,1,2 T. Yildirim,1, Honolulu, Hawaii 96822, USA (Received 2 June 2004; published 3 August 2004) We have studied the structure, energetics, and dynamics of pure and Ti-doped sodium alanate NaAlH4 , focusing on the possibility

Yildirim, Taner

458

The feasibility of meeting the World Health Organization guidelines for sodium and potassium: a cross-national comparison study  

E-Print Network [OSTI]

and meat/poultry mixed dishes, are among the most important sources of dietary sodium in the US.31 32 Processed foods, including breads, cereals and grains contribute a majority of sodium in the United Kingdom, and France as well.12 33 It is important...

Drewnowski, Adam; Rehm, Colin D.; Maillot, Matthieu; Mendoza, Alfonso; Monsivais, Pablo

2015-01-01T23:59:59.000Z

459

Nature and distribution of iron sites in a sodium silicate glass investigated by neutron diffraction and EPSR simulation  

E-Print Network [OSTI]

1 Nature and distribution of iron sites in a sodium silicate glass investigated by neutron distributed in the silicate network and shares corner with silicate tetrahedra. The existence of a majority, such as the increase of the elastic modulus of sodium silicate glasses with increasing Fe-concentration. Our data

Boyer, Edmond

460

The light meson spectroscopy program  

SciTech Connect (OSTI)

Recent discoveries of a number of unexpected new charmomium-like meson states at the BaBar and Belle B-factories have demonstrated how little is still known about meson spectroscopy. In this talk we will review recent highlights of the light quark spectroscopy from collider and fixed target experiments.

Smith, Elton S. [JLAB

2014-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "low-pressure sodium lighting" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Metacapacitors for LED Lighting: Metacapacitors  

SciTech Connect (OSTI)

ADEPT Project: The CUNY Energy Institute is developing less expensive, more efficient, smaller, and longer-lasting power converters for energy-efficient LED lights. LEDs produce light more efficiently than incandescent lights and last significantly longer than compact fluorescent bulbs, but they require more sophisticated power converter technology, which increases their cost. LEDs need more sophisticated converters because they require a different type of power (low voltage direct current, or DC) than what's generally supplied by power outlets. The CUNY Energy Institute is developing sophisticated power converters for LEDs that contain capacitors made from new, nanoscale materials. Capacitors are electrical components that are used to store energy. CUNY's unique capacitors are configured with advanced power circuits to more efficiently control and convert power to the LED lighting source. They also eliminate the need for large magnetic components, instead relying on networks of capacitors that can be easily printed on plastic substrate. CUNY's prototype LED power converter already meets DOE's 2020 projections for the energy efficiency of LED power converters.

None

2010-09-02T23:59:59.000Z

462

Bright prospects for lighting retrofits  

SciTech Connect (OSTI)

Great potential for energy savings can be found in the alleys, hallways and stairwells of multifamily buildings, but this potential is not always easy to realize. This article discusses the solution to common problems, retrofitting mistakes, retrofitting for savings, replacements for incandescent bulbs, better exit lights. 1 fig., 1 tab.

Hasterok, L. [Wisconsin Energy Conservation Corp., Madison, WI (United States)

1995-09-01T23:59:59.000Z

463

National Synchrotron Light Source II  

ScienceCinema (OSTI)

The National Synchrotron Light Source II (NSLS-II) at the U.S. Department of Energy's Brookhaven National Laboratory is a proposed new state-of-the-art medium energy storage ring designed to deliver world-leading brightness and flux with top-off operation

Steve Dierker

2010-01-08T23:59:59.000Z

464

High Performance Outdoor Lighting Accelerator  

Broader source: Energy.gov [DOE]

Hosted by the U.S. Department of Energy (DOE)’s Weatherization and Intergovernmental Programs Office (WIPO), this webinar covered the expansion of the Better Buildings platform to include the newest initiative for the public sector: the High Performance Outdoor Lighting Accelerator (HPOLA).

465

CSC418 / CSCD18 / CSC2504 Basic Lighting and Reflection 8 Basic Lighting and Reflection  

E-Print Network [OSTI]

CSC418 / CSCD18 / CSC2504 Basic Lighting and Reflection 8 Basic Lighting and Reflection Up things, on the lighting that illuminates the scene, and on the interaction of light with the objects in the scene. Some of the basic qualitative properties of lighting and object reflectance that we need

Toronto, University of

466

Light Collages: Lighting Design for Effective Visualization Chang Ha Lee Xuejun Hao Amitabh Varshney  

E-Print Network [OSTI]

Light Collages: Lighting Design for Effective Visualization Chang Ha Lee Xuejun Hao Amitabh 20742 {chlee, hao, varshney}@cs.umd.edu ABSTRACT We introduce Light Collages ­ a lighting design system perception of features with lighting that is locally consistent and globally inconsistent. Inspired

Varshney, Amitabh

467

Enhanced coupling of light from organic light emitting diodes using nanoporous films  

E-Print Network [OSTI]

Enhanced coupling of light from organic light emitting diodes using nanoporous films H. J. Peng, Y the light extraction efficiency for organic light emitting diode OLED . Nanoporous alumina film was used by Bragg scattering. The corrugated light- emitting diode had two-times the efficiency as compared

468

Simultaneous measurement of the surface temperature and the release of atomic sodium from a burning black liquor droplet  

SciTech Connect (OSTI)

Simultaneous measurement of the concentration of released atomic sodium, swelling, surface and internal temperature of a burning black liquor droplet under a fuel lean and rich condition has been demonstrated. Two-dimensional two-colour optical pyrometry was employed to determine the distribution of surface temperature and swelling of a burning black liquor droplet while planar laser-induced fluorescence (PLIF) was used to assess the temporal release of atomic sodium. The key findings of these studies are: (i) the concentration of atomic sodium released during the drying and devolatilisation stages was found to be correlated with the external surface area; and (ii) the insignificant presence of atomic sodium during the char consumption stage shows that sodium release is suppressed by the lower temperature and by the high CO{sub 2} content in and around the particle. (author)

Saw, Woei L.; Nathan, Graham J. [Centre for Energy Technology, The University of Adelaide, SA 5006 (Australia); School of Mechanical Engineering, The University of Adelaide (Australia); Ashman, Peter J.; Alwahabi, Zeyad T. [Centre for Energy Technology, The University of Adelaide, SA 5006 (Australia); School of Chemical Engineering, The University of Adelaide (Australia); Hupa, Mikko [Process Chemistry Centre, Aabo Akademi, Biskopsgatan 8 FI-20500 Aabo (Finland)

2010-04-15T23:59:59.000Z

469

Sodium shortage as a constraint on the carbon cycle in an inland tropical rainforest  

E-Print Network [OSTI]

Sodium shortage as a constraint on the carbon cycle in an inland tropical rainforest Michael- composition of pure cellulose by up to 50%, compared with stream water alone. These effects emerged after 134). We provide experimental evidence that Na shortage slows the carbon cycle. Because 80% of global

Kaspari, Mike

470

Advanced Materials for Sodium-Beta Alumina Batteries: Status, Challenges and Perspectives  

SciTech Connect (OSTI)

The increasing penetration of renewable energy and the trend toward clean, efficient transportation have spurred growing interests in sodium-beta alumina batteries that store electrical energy via sodium ion transport across a ?"-Al2O3 solid electrolyte at elevated temperatures (typically 300~350°C). Currently, the negative electrode or anode is metallic sodium in molten state during battery operation; the positive electrode or cathode can be molten sulfur (Na-S battery) or solid transition metal halides plus a liquid phase secondary electrolyte (e.g., ZEBRA battery). Since the groundbreaking works in the sodium-beta alumina batteries a few decades ago, encouraging progress has been achieved in improving battery performance, along with cost reduction. However there remain issues that hinder broad applications and market penetration of the technologies. To better the Na-beta alumina technologies require further advancement in materials along with component and system design and engineering. This paper offers a comprehensive review on materials of electrodes and electrolytes for the Na-beta alumina batteries and discusses the challenges ahead for further technology improvement.

Lu, Xiaochuan; Xia, Guanguang; Lemmon, John P.; Yang, Zhenguo

2010-05-01T23:59:59.000Z

471

Review of FY2001 Development Work for Vitrification of Sodium Bearing Waste  

SciTech Connect (OSTI)

Treatment of sodium-bearing waste (SBW) at the Idaho Nuclear Technology and Engineering Center (INTEC) within the Idaho National Engineering and Environmental Laboratory is mandated by the Settlement Agreement between the Department of Energy and the State of Idaho. This report discusses significant findings from vitrification technology development during 2001 and their impacts on the design basis for SBW vitrification.

Barnes, C.M.; Taylor, D.D.

2002-09-09T23:59:59.000Z

472

Deficiencies of sodium and iodine in grazing sheep in northern China  

E-Print Network [OSTI]

Deficiencies of sodium and iodine in grazing sheep in northern China DG Masters JR Lindsay SX Yu DX of Traditional Veterinary Medicine, Chinese Academy of Agricultural Science, Xiaoxihu, Lanzhou, Gansu, China An examination of the mineral status of grazing sheep at 3 sites in northern China has provided evidence

Paris-Sud XI, Université de

473

Bonding in Sodium Chloride Nanotubes: A New Analysis via Madelung Constants and Cohesive Energies  

E-Print Network [OSTI]

1 Bonding in Sodium Chloride Nanotubes: A New Analysis via Madelung Constants and Cohesive Energies is introduced which employs a linear relationship between nanotube cohesive energies determined via Density between ionic and cohesive bonding energies indicate that, as the nanotubes become longer, ionic bonding

Hanusa, Christopher

474

Ice iron/sodium film as cause for high noctilucent cloud radar reflectivity  

E-Print Network [OSTI]

Ice iron/sodium film as cause for high noctilucent cloud radar reflectivity P. M. Bellan1 Received] Noctilucent clouds, tiny cold electrically charged ice grains located at about 85 km altitude, exhibit by assuming the ice grains are coated by a thin metal film; substantial evidence exists indicating

Bellan, Paul M.

475

indirect study, coal was oxidatively de-graded with sodium dichromate and the  

E-Print Network [OSTI]

Cleaning Technology (Noyes Data Corporation, Park Ridge, N.J., 1981). 10. Z. Hussain, E. Umbach, D. Aindirect study, coal was oxidatively de- graded with sodium dichromate and the esterified products- vestigators concluded (17, p. 380) that "thiophene derivatives must be indige- nous to coal." The direct XANES

Howat, Ian M.

476

Pressure-Induced Structural Transformations of the Zintl Phase Sodium Silicide Ral Quesada Cabreraa  

E-Print Network [OSTI]

and reduction of Na+ to metallic sodium. We have combined our experimental studies with DFT calculations and germanides belong to the family of Zintl phases, in which polyanionic species, formed of the tetrelide atoms counterbalance the electropositive metal cations [1-3]. These compounds are interesting because the Si and Ge

Paris-Sud XI, Université de

477

Molecular Dynamic Simulation of Sodium in 7-Pin LMFBR Bundle Under Hypothetical Accident Conditions  

SciTech Connect (OSTI)

In the frame of safety analysis of liquid metal fast breeder reactors (LMFBRs) under hypothetical Unprotected Loss of Flow (ULOF) conditions two-phase flow of sodium is simulated in a 7-pin bundle, with hexagonal lattice. Molecular dynamics, with the application of the Direct Simulation Monte Carlo (DSMC) method, and a macroscopic model describing rewetting sequences due to the flow of a sodium liquid film along the pin surfaces, are applied to simulate the coolant in the bundle. The pin surfaces and the inner surface of the hexagonal canning are treated in the Monte Carlo simulation as diffusively reflecting surfaces. Collisions of sodium molecules are computed with the 'hard-sphere' model. With respect to previous work the following improvements of the computational code were made: i) The full bundle is simulated, thus allowing for asymmetries, like a skewed power distribution, to be accounted for; ii) A pin model calculates detailed temperature distributions in the pins, so that temperature boundary conditions are computed and not imposed; iii) Post processing visualisation of computed results was developed. An out of pile sodium boiling experiment run at the Nuclear Research Center of Karlsruhe, Germany, is simulated and conclusions are drawn about the applicability of the methodology in computer codes dedicated to breeder reactors safety analysis. (authors)

Bottoni, Maurizio [University of Ferrara, Physics Department, Via Paradiso 12, I-44100 Ferrara (Italy); Bottoni, Claudio; Scanu, John [University of Pisa, Lungarno Pacinotti, 43 - 56126 Pisa (Italy)

2006-07-01T23:59:59.000Z

478

Original article Increased late sodium current in myocytes from a canine heart failure  

E-Print Network [OSTI]

Original article Increased late sodium current in myocytes from a canine heart failure model and from failing human heart Carmen R. Valdivia, William W. Chu, Jielin Pu 1 , Jason D. Foell, Robert A December 2004 Abstract Electrophysiological remodeling of ion channels in heart failure causes action

Kamp, Tim

479

Mechanism and kinetics of a sodium-driven bacterial flagellar motor  

E-Print Network [OSTI]

Mechanism and kinetics of a sodium-driven bacterial flagellar motor Chien-Jung Loa,b , Yoshiyuki potential difference. It consists of an 50-nm rotor and up to 10 independent stators anchored to the cell of electrical and chemical potential. All 25 torque­speed curves had the same concave-down shape as fully

Berry, Richard

480

determines the number of sodium spikes fired per event by individual cells (Maruta  

E-Print Network [OSTI]

determines the number of sodium spikes fired per event by individual cells (Maruta et al., 2007; Mathy et al., 2009) and may thereby mediate the direction and speed of learning in Purkinje cells (Mathy, apparently even down to the level of electrical synapses of the infe- rior olive (Lefler et al., 2014; Mathy

Oertner, Thomas

Note: This page contains sample records for the topic "low-pressure sodium lighting" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Room-temperature stationary sodium-ion batteries for large-scale electric energy storage  

E-Print Network [OSTI]

energy and utility applications, such as pump hydro, compressed air, y-wheel and electrochemicalRoom-temperature stationary sodium-ion batteries for large-scale electric energy storage Huilin Pan attention particularly in large- scale electric energy storage applications for renewable energy and smart

Wang, Wei Hua

482

Evaluation of a sodium/Hastelloy-X heat pipe for wing leading edge cooling  

SciTech Connect (OSTI)

This report covers assembly of a sodium heat pipe, testing to verify performance during start-up and under steady-state conditions with stagnation point heat loads to about 80 W/cm{sup 2}, performance analysis and evaluation. Evaluation of this leading edge cooling concept is offered and recommendations for further research discussed.

Merrigan, M.A.; Sena, J.T. [Los Alamos National Lab., NM (United States); Glass, D.E. [Analytical Services and Materials, Hampton, VA (United States)

1996-12-31T23:59:59.000Z

483

Effects of Sodium Chloride Particles, Ozone, UV, and Relative Humidity on Atmospheric Corrosion of Silver  

E-Print Network [OSTI]

Effects of Sodium Chloride Particles, Ozone, UV, and Relative Humidity on Atmospheric Corrosion The corrosion of Ag contaminated with NaCl particles in gaseous environments containing humidity and ozone analyzed using a coulometric reduction technique. The atmospheric corrosion of Ag was greatly accelerated

484

Review of FY 2001 Development Work for Vitrification of Sodium Bearing Waste  

SciTech Connect (OSTI)

Treatment of sodium-bearing waste (SBW) at the Idaho Nuclear Technology and Engineering Center (INTEC) within the Idaho National Engineering and Environmental Laboratory is mandated by the Settlement Agreement between the Department of Energy and the State of Idaho. This report discusses significant findings from vitrification technology development during 2001 and their impacts on the design basis for SBW vitrification.

Taylor, Dean Dalton; Barnes, Charles Marshall

2002-09-01T23:59:59.000Z

485

Behavioral/Systems/Cognitive Sodium and Calcium Current-Mediated Pacemaker Neurons  

E-Print Network [OSTI]

Behavioral/Systems/Cognitive Sodium and Calcium Current-Mediated Pacemaker Neurons and Respiratory excitability, which is inconsistent with a pacemaker-essential mechanism of respiratory rhythmogenesis evaluate here in the mamma- lian respiratory network. The cellular mechanisms that underlie respiratory

Del Negro, Christopher A.

486

Effect of lasalocid sodium on rumen fermentation and digestion in sheep  

E-Print Network [OSTI]

Effect of lasalocid sodium on rumen fermentation and digestion in sheep P. THIVEND, J.-P. JOUANY Laboratoire de la Digestion des Ruminants, 1. N. R. A., Theix, 63122 Ceyrat France. Summary. Four adult sheep had taken place in the rumen bacterial population (table 3). Overall digestive utilization of organic

Paris-Sud XI, Université de

487

Modeling Zinc and Sodium Chloride Migration in Vadose Zone Soils Beneath Stormwater Infiltration Devices  

E-Print Network [OSTI]

be seen in the field. Based on model results, shallow groundwater will be rapidly and highly impactedModeling Zinc and Sodium Chloride Migration in Vadose Zone Soils Beneath Stormwater Infiltration device. Introduction Urbanization has increased the amount of impervious surfaces, leading to an increase

Clark, Shirley E.

488

Power Quality Improvements in Lighting Systems Mr. Ashish Shrivastava  

E-Print Network [OSTI]

from early incandescent lamps to present generation light emitting diodes (LEDs). Incandescent light

Kumar, M. Jagadesh

489

Legislative Directive: EISA 2007, Subtitle B: Lighting Energy Efficiency  

Broader source: Energy.gov [DOE]

Legislative Directive: EISA 2007, Subtitle B: Lighting Energy Efficiency, Sec. 321: Lighting Energy Efficiency

490

Final Environmental Impact Statement for the Treatment and Management of Sodium-Bonded Spent Nuclear Fuel  

SciTech Connect (OSTI)

DOE is responsible for the safe and efficient management of its sodium-bonded spent nuclear fuel. This fuel contains metallic sodium, a highly reactive material; metallic uranium, which is also reactive; and in some cases, highly enriched uranium. The presence of reactive materials could complicate the process of qualifying and licensing DOE's sodium-bonded spent nuclear fuel inventory for disposal in a geologic repository. Currently, more than 98 percent of this inventory is located at the Idaho National Engineering and Environmental Laboratory (INEEL), near Idaho Falls, Idaho. In addition, in a 1995 agreement with the State of Idaho, DOE committed to remove all spent nuclear fuel from Idaho by 2035. This EIS evaluates the potential environmental impacts associated with the treatment and management of sodium-bonded spent nuclear fuel in one or more facilities located at Argonne National Laboratory-West (ANL-W) at INEEL and either the F-Canyon or Building 105-L at the Savannah River Site (SRS) near Aiken, South Carolina. DOE has identified and assessed six proposed action alternatives in this EIS. These are: (1) electrometallurgical treatment of all fuel at ANL-W, (2) direct disposal of blanket fuel in high-integrity cans with the sodium removed at ANL-W, (3) plutonium-uranium extraction (PUREX) processing of blanket fuel at SRS, (4) melt and dilute processing of blanket fuel at ANL-W, (5) melt and dilute processing of blanket fuel at SRS, and (6) melt and dilute processing of all fuel at ANL-W. In addition, Alternatives 2 through 5 include the electrometallurgical treatment of driver fuel at ANL-W. Under the No Action Alternative, the EIS evaluates both the continued storage of sodium-bonded spent nuclear fuel until the development of a new treatment technology or direct disposal without treatment. Under all of the alternatives, the affected environment is primarily within 80 kilometers (50 miles) of spent nuclear fuel treatment facilities. Analyses indicate little difference in the environmental impacts among alternatives. DOE has identified electrometallurgical treatment as its Preferred Alternative for the treatment and management of all sodium-bonded spent nuclear fuel, except for the Fermi-1 blanket fuel. The No Action Alternative is preferred for the Fermi-1 blanket spent nuclear fuel.

N /A

2000-08-04T23:59:59.000Z

491

Lighting the Way with Compact Fluorescent Lighting | Department of Energy  

Energy Savers [EERE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion |Energy UsageAUDITVehicles »Exchange Visitorsfor Shade Landscaping for ShadeLessonsLight

492

Lighting  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: VegetationEquipment Surfaces and Interfaces Sample6, 2011 LawrenceEfeedstocks

493

Effect of Sodium Carboxymethyl Celluloses on Water-catalyzed Self-degradation of 200-degree C-heated Alkali-Activated Cement  

SciTech Connect (OSTI)

We investigated the usefulness of sodium carboxymethyl celluloses (CMC) in promoting self-degradation of 200°C-heated sodium silicate-activated slag/Class C fly ash cementitious material after contact with water. CMC emitted two major volatile compounds, CO2 and acetic acid, creating a porous structure in cement. CMC also reacted with NaOH from sodium silicate to form three water-insensitive solid reaction products, disodium glycolate salt, sodium glucosidic salt, and sodium bicarbonate. Other water-sensitive solid reaction products, such as sodium polysilicate and sodium carbonate, were derived from hydrolysates of sodium silicate. Dissolution of these products upon contact with water generated heat that promoted cement’s self-degradation. Thus, CMC of high molecular weight rendered two important features to the water-catalyzed self-degradation of heated cement: One was the high heat energy generated in exothermic reactions in cement; the other was the introduction of extensive porosity into cement.

Sugama T.; Pyatina, T.

2012-05-01T23:59:59.000Z

494

Demonstration Assessment of Light Emitting Diode (LED) Commercial Garage Lights In the Providence Portland Medical Center, Portland, Oregon  

SciTech Connect (OSTI)

This U.S. Department of Energy GATEWAY Demonstration project studied the applicability of light-emitting diode (LED) luminaires for commercial parking garage applications. High-pressure sodium (HPS) area luminaires were replaced with new LED area luminaires. The project was supported under the U.S. Department of Energy (DOE) Solid State Lighting Program. Other participants in the demonstration project included Providence Portland Medical Center in Portland, Oregon, the Energy Trust of Oregon, and Lighting Sciences Group (LSG) Inc. Pacific Northwest National Laboratory (PNNL) conducted the measurements and analysis of the results. PNNL manages GATEWAY demonstrations for DOE and represents their perspective in the conduct of the work. Quantitative and qualitative measurements of light and electrical power were taken at the site for both HPS and LED light sources. Economic costs were estimated and garage users’ responses to the new light sources were gauged with a survey. Six LED luminaires were installed in the below-ground parking level A, replacing six existing 150W HPS lamps spread out over two rows of parking spaces. Illuminance measurements were taken at floor level approximately every 4 ft on a 60-ft x 40-ft grid to measure light output of these LED luminaires which were termed the “Version 1” luminaires. PNNL conducted power measurements of the circuit in the garage to which the 6 luminaires were connected and determined that they drew an average of 82 W per lamp. An improved LED luminaire, Version 2, was installed in Level B of the parking garage. Illuminance measurements were not made of this second luminaire on site due to higher traffic conditions, but photometric measurements of this lamp and Version 1 were made in an independent testing laboratory and power usage for Version 2 was also measured. Version 1 was found to produce 3600 lumens and Version 2 was found to produce 4700 lumens of light and to consume 78 Watts. Maximum and minimum light levels were measured for the HPS and LED Version 1 luminaires and projected for the Version 2 luminaires. Maximum light levels were 23.51 foot candles, 20.54 fc, and 26.7 fc respectively and minimum light levels were 1.49 fc, 1.45 fc, and 1.88 fc. These results indicate very similar or even slightly higher light levels produced by the LED lamps, despite the higher lumen output of the HPS lamp. The LED lamps provide higher luminaire efficacy because all of the light is directed down and out. None of it is “lost” in the fixture. Also the HPS luminaire had poorly designed optics and a plastic covering that tended to get dirty and cracked, further decreasing the realized light output.[is this an accurate way to say this?] Consumer perceptions of the Version 2 LED were collected via a written survey form given to maintenance and security personnel. More than half felt the LED luminaires provided more light than the HPS lamps and a majority expressed a preference for the new lamps when viewing the relamped area through a security camera. Respondents commented that the LED luminaires were less glary, created less shadows, had a positive impact on visibility, and improved the overall appearance of the area. PNNL conducted an economic analysis and found that the Version 1 lamp produced annual energy savings of 955 kWh and energy cost savings of $76.39 per lamp at electricity rates of 6.5 cents per kWh and $105.03 at 11 cents per kWh. PNNL found that the Version 2 lamp produced annual energy savings of 991 kWh and energy cost savings of $79.26 per lamp at electricity rates of 6.5 cents per kWh and $108.98 at 11 cents per kWh. PNNL also calculated simple payback and found that Version 1 showed paybacks of 5.4 yrs at 6.5c/kWh and 4.1 yrs at 11c/kWh while Version 2 showed paybacks of 5.2 yrs at 6.5c/kWh and 3.9 yrs at 11c/kWh.

Ton, My K.; Richman, Eric E.; Gilbride, Theresa L.

2008-11-11T23:59:59.000Z

495

Monitored lighting energy savings from dimmable lighting controls in The New York Times Headquarters Building  

E-Print Network [OSTI]

A. , D’Herdt, P. , 2008, Lighting energy savings in officesLux Europa, 11 th European Lighting Conference, Istanbul,evaluation of the dimmable lighting, automated shading, and

Fernandes, Luis L.

2014-01-01T23:59:59.000Z

496

LIGHTING RESEARCH PROGRAM Project 5.4 DALI Lighting Control Device Standard  

E-Print Network [OSTI]

LIGHTING RESEARCH PROGRAM Project 5.4 DALI Lighting Control Device Standard Development FINAL CONTROL DEVICE STANDARD PROPOSED BY NEMA ......10 TECHNICAL ASSESSMENT REPORT Electronics Co.; Al Lombardi, Leviton Manufacturing Co., Inc.; Mike Stein, Universal Lighting Technologies

497

E-Print Network 3.0 - aluminum sodium fluoride Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Information Sciences 28 List of Acronyms, Abbreviations and Symbols Summary: Light Emitting Diode LiAlH4 lithium aluminum hydride LiF lithium fluoride LS Light Scattering...

498

Lighting system with thermal management system  

DOE Patents [OSTI]

Lighting systems having unique configurations are provided. For instance, the lighting system may include a light source, a thermal management system and driver electronics, each contained within a housing structure. The light source is configured to provide illumination visible through an opening in the housing structure. The thermal management system is configured to provide an air flow, such as a unidirectional air flow, through the housing structure in order to cool the light source. The driver electronics are configured to provide power to each of the light source and the thermal management system.

Arik, Mehmet; Weaver, Stanton; Stecher, Thomas; Seeley, Charles; Kuenzler, Glenn; Wolfe, Jr., Charles; Utturkar, Yogen; Sharma, Rajdeep; Prabhakaran, Satish; Icoz, Tunc

2013-05-07T23:59:59.000Z

499

Variable area light reflecting assembly  

DOE Patents [OSTI]

Device for tracking daylight and projecting it into a building. The device tracks the sun and automatically adjusts both the orientation and area of the reflecting surface. The device may be mounted in either a wall or roof of a building. Additionally, multiple devices may be employed in a light shaft in a building, providing daylight to several different floors. The preferred embodiment employs a thin reflective film as the reflecting device. One edge of the reflective film is fixed, and the opposite end is attached to a spring-loaded take-up roller. As the sun moves across the sky, the take-up roller automatically adjusts the angle and surface area of the film. Additionally, louvers may be mounted at the light entrance to the device to reflect incoming daylight in an angle perpendicular to the device to provide maximum reflective capability when daylight enters the device at non-perpendicular angles.

Howard, Thomas C. (Raleigh, NC)

1986-01-01T23:59:59.000Z

500

Variable area light reflecting assembly  

DOE Patents [OSTI]

Device is described for tracking daylight and projecting it into a building. The device tracks the sun and automatically adjusts both the orientation and area of the reflecting surface. The device may be mounted in either a wall or roof of a building. Additionally, multiple devices may be employed in a light shaft in a building, providing daylight to several different floors. The preferred embodiment employs a thin reflective film as the reflecting device. One edge of the reflective film is fixed, and the opposite end is attached to a spring-loaded take-up roller. As the sun moves across the sky, the take-up roller automatically adjusts the angle and surface area of the film. Additionally, louvers may be mounted at the light entrance to the device to reflect incoming daylight in an angle perpendicular to the device to provide maximum reflective capability when daylight enters the device at non-perpendicular angles. 9 figs.

Howard, T.C.

1986-12-23T23:59:59.000Z