National Library of Energy BETA

Sample records for logs cement bond

  1. Cement Bond Log | Open Energy Information

    Open Energy Info (EERE)

    casing and cement and between cement and borehole wall. Most cement-bond logs are a measurement only of the amplitude of the early arriving casing signal. Although a small...

  2. Mud Logging | Open Energy Information

    Open Energy Info (EERE)

    Well Log Techniques Acoustic Logs Cement Bond Log Cross-Dipole Acoustic Log Caliper Log Chemical Logging Density Log Gamma Log Image Logs Mud Logging Neutron Log Pressure...

  3. Phosphate-bonded calcium aluminate cements

    DOE Patents [OSTI]

    Sugama, T.

    1993-09-21

    A method is described for making a rapid-setting phosphate-bonded cementitious material. A powdered aluminous cement is mixed with an aqueous solution of ammonium phosphate. The mixture is allowed to set to form an amorphous cementitious material which also may be hydrothermally treated at a temperature of from about 120 C to about 300 C to form a crystal-containing phosphate-bonded material. Also described are the cementitious products of this method and the cement composition which includes aluminous cement and ammonium polyphosphate. 10 figures.

  4. Phosphate-bonded calcium aluminate cements

    DOE Patents [OSTI]

    Sugama, Toshifumi

    1993-01-01

    A method is described for making a rapid-setting phosphate-bonded cementitious material. A powdered aluminous cement is mixed with an aqueous solution of ammonium phosphate. The mixture is allowed to set to form an amorphous cementitious material which also may be hydrothermally treated at a temperature of from about 120.degree. C. to about 300.degree. C. to form a crystal-containing phosphate-bonded material. Also described are the cementitious products of this method and the cement composition which includes aluminous cement and ammonium polyphosphate.

  5. Map of Cement Site

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    cement

  6. ULTRA-LIGHTWEIGHT CEMENT

    SciTech Connect (OSTI)

    Fred Sabins

    2002-07-30

    The objective of this project is to develop an improved ultra-lightweight cement using ultra-lightweight hollow glass spheres (ULHS). This report includes results from laboratory testing of ULHS systems along with other lightweight cement systems, including foamed and sodium silicate slurries. During this project quarter, a comparison study of the three cement systems examined the effect that cement drillout has on the three cement systems. Testing to determine the effect of pressure cycling on the shear bond properties of the cement systems was also conducted. This report discusses testing that was performed to analyze the alkali-silica reactivity of ULHS in cement slurries.

  7. ULTRA-LIGHTWEIGHT CEMENT

    SciTech Connect (OSTI)

    Fred Sabins

    2002-04-29

    The objective of this project is to develop an improved ultra-lightweight cement using ultra-lightweight hollow glass spheres (ULHS). This report includes results from laboratory testing of ULHS systems along with other lightweight cement systems, including foamed and sodium silicate slurries. During this project quarter, comparison studies of the three cement systems examined several properties: tensile strength, Young's modulus, and shear bond. Testing to determine the effect of temperature cycling on the shear bond properties of the cement systems was also conducted. In addition, the stress-strain behavior of the cement types was studied. This report discusses a software program that is being developed to help design ULHS cements and foamed cements.

  8. ULTRA-LIGHTWEIGHT CEMENT

    SciTech Connect (OSTI)

    Fred Sabins

    2002-10-31

    The objective of this project is to develop an improved ultra-lightweight cement using ultra-lightweight hollow glass spheres (ULHS). This report includes results from laboratory testing of ULHS systems along with other lightweight cement systems, including foamed and sodium silicate slurries. During this project quarter, a comparison study of the three cement systems examined the effect that cement drillout has on the three cement systems. Testing to determine the effect of pressure cycling on the shear bond properties of the cement systems was also conducted. This report discusses testing that will be performed for analyzing the alkali-silica reactivity of ULHS in cement slurries, as well as the results of Field Tests 1 and 2.

  9. ULTRA-LIGHTWEIGHT CEMENT

    SciTech Connect (OSTI)

    Fred Sabins

    2002-01-23

    The objective of this project is to develop an improved ultra-lightweight cement using ultra-lightweight hollow glass spheres (ULHS). This report includes results from laboratory testing of ULHS systems along with other lightweight cement systems: foamed and sodium silicate slurries. Comparison studies of the three cement systems examined several properties: tensile strength, Young's modulus, water permeability, and shear bond. Testing was also done to determine the effect that temperature cycling has on the shear bond properties of the cement systems. In addition, analysis was carried out to examine alkali silica reactivity of slurries containing ULHS. Data is also presented from a study investigating the effects of mixing and pump circulation on breakage of ULHS. Information is also presented about the field application of ULHS in cementing a 7-in. intermediate casing in south Texas.

  10. Change Log

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NERSC-8 Trinity Benchmarks Change Log 09032013 Correction applied to MiniDFT web-page ... results spreadsheet (linked on SSP web page); clarification to benchmark run rules ...

  11. Change Log

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Change Log Change Log Crossroads/NERSC-9 Benchmarks Change Log 05/25/2016 Updated to latest version 3.0 release of the HPCG distribution. For the APEX benchmark, the -DHPCG_CONTIGUOUS_ARRAYS flag is now used which improves the baseline performance on Edison significantly. Please refer to the updated SSI spreadsheet for the new baseline value. 05/17/2016 Updated source distribution. README.APEX now states to use "Grind Time" as the figure of merit. Failed to do this on the 5/10/2016

  12. Change Log

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Change Log Change Log NERSC-8 / Trinity Benchmarks Change Log 09/03/2013 Correction applied to MiniDFT web-page (to remove inconsistency with MiniDFT README). Capability Improvement measurements do not require 10,000 MPI ranks per k-point. 08/06/2013 Various pages have changed to remove "draft" status 08/02/2013 Correction added to FLOP Counts for "Small" Single-Node Miniapplication Tests page 07/12/2013 README files updated for IOR benchmark to correct an error in wording

  13. Outage Log

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Queue Look Scheduled Outages Outage Log Science Gateway Status Login Node Status ... It is a historical record and may not be updated while a system event is in progress. ...

  14. Log Summarization

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Log Summarization and Anomaly Detection for Troubleshooting Distributed Systems Dan Gunter #1 , Brian L. Tierney #2 , Aaron Brown ∗3 , Martin Swany ∗4 , John Bresnahan !5 , Jennifer M. Schopf !6 # Lawrence Berkeley National Laboratory, Berkeley, CA, USA 1 dkgunter@lbl.gov 2 bltierney@lbl.gov ∗ University of Delaware, Newark, DE, USA 3 brown@cis.udel.edu 4 swany@cis.udel.edu ! Argonne National Laboratory, Argonne, IL, USA 5 bresnaha@mcs.anl.gov 6 jms@mcs.anl.gov Abstract- Today's system

  15. Quantification of Wellbore Leakage Risk Using Non-destructive Borehole Logging Techniques

    SciTech Connect (OSTI)

    Duguid, Andrew; Butsch, Robert; Cary, J.; Celia, Michael; Chugunov, Nikita; Gasda, Sarah; Hovorka, Susan; Ramakrishnan, T. S.; Stamp, Vicki; Thingelstad, Rebecca; Wang, James

    2014-08-29

    estimate the flow properties modeling of point pressure tests, modeling of vertical interference tests, and laboratory measurement of cased-hole sidewall cores The wells were in sufficiently good shape to allow the development of the characterization methods while still having enough defects to study differences in results as they relate to well integrity. Samples and tests analyzed from three of five wells studied in showed the cements were largely intact and had not degraded from exposure native brines. Log results taken in conjunction with the core measurements indicate that interfaces and/or problems with cement placement due to eccentering provide preferential flow paths for fluids, which can increase the effective permeability of the barrier several orders of magnitude above the permeability of intact cement. The results of the maps created using logging tools indicating that the cement condition and bond are generally good identify a need for more research to understand how logs can be used to predicteffective well permeabilities such as those measured by the VITs in this study.

  16. Spontaneous Potential Well Log | Open Energy Information

    Open Energy Info (EERE)

    Log Chemical Logging Density Log Gamma Log Image Logs Mud Logging Neutron Log Pressure Temperature Log Single-Well and Cross-Well Resistivity Spontaneous Potential Well Log...

  17. Log-Tool

    SciTech Connect (OSTI)

    Goodall, John

    2012-05-21

    Log files are typically semi- or un-structured. To be useable for visualization and machine learning, they need to be parsed into a standard, structured format. Log-tool is a tool for facilitating the parsing, structuring, and routing of log files (e.g. intrusion detection long, web server logs, system logs). It consists of three main components: (1) Input – it will input data from files, standard input, and syslog, (2) Parser – it will parse the log file based on regular expressions into structured data (JSNO format), (3) Output – it will output structured data into commonly used formats, including Redis (a database), standard output, and syslog.

  18. AIRMaster+ LogTool

    Broader source: Energy.gov [DOE]

    The AIRMaster+ LogTool is a companion tool to AIRMaster+ that helps industrial users determine the operating dynamics of a compressed system. Use the LogTool first to gather critical data in...

  19. Zinc electrode with cement additive

    DOE Patents [OSTI]

    Charkey, Allen

    1982-06-01

    A zinc electrode having a cement additive, preferably, Portland Cement, distributed in the zinc active material.

  20. Well Log ETL tool

    Energy Science and Technology Software Center (OSTI)

    2013-08-01

    This is an executable python script which offers two different conversions for well log data: 1) Conversion from a BoreholeLASLogData.xls model to a LAS version 2.0 formatted XML file. 2) Conversion from a LAS 2.0 formatted XML file to an entry in the WellLog Content Model. Example templates for BoreholeLASLogData.xls and WellLogsTemplate.xls can be found in the package after download.

  1. Caliper Log | Open Energy Information

    Open Energy Info (EERE)

    Information Exploration Group: Downhole Techniques Exploration Sub Group: Well Log Techniques Parent Exploration Technique: Well Log Techniques Information Provided by...

  2. Log-Tool

    Energy Science and Technology Software Center (OSTI)

    2012-05-21

    Log files are typically semi- or un-structured. To be useable for visualization and machine learning, they need to be parsed into a standard, structured format. Log-tool is a tool for facilitating the parsing, structuring, and routing of log files (e.g. intrusion detection long, web server logs, system logs). It consists of three main components: (1) Input – it will input data from files, standard input, and syslog, (2) Parser – it will parse the logmore » file based on regular expressions into structured data (JSNO format), (3) Output – it will output structured data into commonly used formats, including Redis (a database), standard output, and syslog.« less

  3. Logging in to Edison

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Logging in Logging in to Edison Interactive Access You can log in to Edison using SSH (Secure Shell) with the following command from any UNIX, Mac OS X, Linux, FreeBSD, etc. command shell or terminal: ssh -l username edison.nersc.gov There are several SSH-capable clients available for Windows, Mac, and UNIX/Linux machines. NERSC does not support or recommend any particular client. Edison has 12 login nodes. You will be randomly connected to one of those 12 when you ssh to edison.nersc.gov. In

  4. Logging in to Franklin

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Logging in Logging in to Franklin Interactive Access You can log in to Franklin using SSH (Secure Shell) with the following command from any UNIX, Linux, FreeBSD, etc. command shell or terminal: % ssh -l username franklin.nersc.gov There are a number of SSH-capable clients available for Windows, Mac, and UNIX/Linux machines. NERSC does not support or recommend any particular client. Franklin has 10 login nodes; you will be randomly connected to one of those 10 when you ssh to franklin.nersc.gov.

  5. Logging in to Hopper

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Logging in Logging in to Hopper Interactive Access You can log in to Hopper using SSH (Secure Shell) with the following command from any UNIX, Mac OS X, Linux, FreeBSD, etc. command shell or terminal: ssh -l username hopper.nersc.gov There are several SSH-capable clients available for Windows, Mac, and UNIX/Linux machines. NERSC does not support or recommend any particular client. Hopper has 12 login nodes. You will be randomly connected to one of those 12 when you ssh to hopper.nersc.gov. In

  6. ULTRA-LIGHTWEIGHT CEMENT

    SciTech Connect (OSTI)

    Fred Sabins

    2003-10-31

    The objective of this project is to develop an improved ultra- lightweight cement using ultra-lightweight hollow glass spheres (ULHS). This report discusses testing that was performed for analyzing the alkali-silica reactivity of ULHS in cement slurries.

  7. MECS 2006- Cement

    Office of Energy Efficiency and Renewable Energy (EERE)

    Manufacturing Energy and Carbon Footprint for Cement (NAICS 327310) Sector with Total Energy Input, October 2012 (MECS 2006)

  8. Acoustic Logs | Open Energy Information

    Open Energy Info (EERE)

    different types of acoustic logs are used, based on the frequencies used, the way the signal is recorded, and the purpose of the log. All these logs require fluid in the well to...

  9. Density Log | Open Energy Information

    Open Energy Info (EERE)

    Density Log Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Technique: Density Log Details Activities (7) Areas (6) Regions (0) NEPA(0) Exploration...

  10. NMR logging apparatus

    DOE Patents [OSTI]

    Walsh, David O; Turner, Peter

    2014-05-27

    Technologies including NMR logging apparatus and methods are disclosed. Example NMR logging apparatus may include surface instrumentation and one or more downhole probes configured to fit within an earth borehole. The surface instrumentation may comprise a power amplifier, which may be coupled to the downhole probes via one or more transmission lines, and a controller configured to cause the power amplifier to generate a NMR activating pulse or sequence of pulses. Impedance matching means may be configured to match an output impedance of the power amplifier through a transmission line to a load impedance of a downhole probe. Methods may include deploying the various elements of disclosed NMR logging apparatus and using the apparatus to perform NMR measurements.

  11. ULTRA-LIGHTWEIGHT CEMENT

    SciTech Connect (OSTI)

    Fred Sabins

    2001-07-18

    The objective of this project is to develop an improved ultra-lightweight cement using ultra-lightweight hollow glass spheres (ULHS). Work reported herein addresses Task 1: Assess Ultra-Lightweight Cementing Issues, Task 2: Review Russian Ultra-Lightweight Cement Literature, Task 3: Test Ultra-Lightweight Cements, and Task 8: Develop Field ULHS Cement Blending and Mixing Techniques. Results reported this quarter include: preliminary findings from a literature review focusing on problems associated with ultra-lightweight cements; summary of pertinent information from Russian ultra-lightweight cement literature review; laboratory tests comparing ULHS slurries to foamed slurries and sodium silicate slurries for two different applications; and initial laboratory studies with ULHS in preparation for a field job.

  12. Log in | The Ames Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Error message Access denied. You must log in to view this page.

  13. Logs Perl Module

    Energy Science and Technology Software Center (OSTI)

    2007-04-04

    A perl module designed to read and parse the voluminous set of event or accounting log files produced by a Portable Batch System (PBS) server. This module can filter on date-time and/or record type. The data can be returned in a variety of formats.

  14. ULTRA-LIGHTWEIGHT CEMENT

    SciTech Connect (OSTI)

    Fred Sabins

    2001-01-15

    The objective of this project is to develop an improved ultra-lightweigh cement using ultralight hollow glass spheres (ULHS). Work reported herein addresses Task 1: Assess Ultra-Lightweight Cementing Problems, Task 2: Review Russian Ultra-Lightweight Cement Literature, and Task 3: Test Ultra-Lightweight Cements. Results reported this quarter include a review and summary surface pipe and intermediate casing cementing conditions historically encountered in the US and establishment of average design conditions for ULHS cements. Russian literature concerning development and use of ultra-lightweight cements employing either nitrogen or ULHS was reviewed, and a summary is presented. Quality control testing of materials used to formulate ULHS cements in the laboratory was conducted to establish baseline material performance standards. A testing protocol was developed employing standard procedures as well as procedures tailored to evaluate ULHS. This protocol is presented and discussed. finally, results of initial testing of ULHS cements is presented along with analysis to establish cement performance design criteria to be used during the remainder of the project.

  15. ULTRA-LIGHTWEIGHT CEMENT

    SciTech Connect (OSTI)

    Fred Sabins

    2003-01-31

    The objective of this project is to develop an improved ultra-lightweight cement using ultra-lightweight hollow glass spheres (ULHS). This report discusses testing that was performed for analyzing the alkali-silica reactivity of ULHS in cement slurries. DOE joined the Materials Management Service (MMS)-sponsored joint industry project ''Long-Term Integrity of Deepwater Cement under Stress/Compaction Conditions.'' Results of the project contained in two progress reports are also presented in this report.

  16. Neutron Log | Open Energy Information

    Open Energy Info (EERE)

    Dictionary.png Neutron Log: The neutron log responds primarily to the amount of hydrogen in the formation which is contained in oil, natural gas, and water. The amount of...

  17. ULTRA-LIGHTWEIGHT CEMENT

    SciTech Connect (OSTI)

    Fred Sabins

    2004-01-30

    The objective of this project is to develop an improved ultra-lightweight cement using ultra-lightweight hollow glass spheres (ULHS). This report discusses testing that was performed for analyzing the alkali-silica reactivity of ULHS in cement slurries.

  18. Grid Logging: Best Practices Guide

    SciTech Connect (OSTI)

    Tierney, Brian L; Tierney, Brian L; Gunter, Dan

    2008-04-01

    The purpose of this document is to help developers of Grid middleware and application software generate log files that will be useful to Grid administrators, users, developers and Grid middleware itself. Currently, most of the currently generated log files are only useful to the author of the program. Good logging practices are instrumental to performance analysis, problem diagnosis, and security auditing tasks such as incident tracing and damage assessment. This document does not discuss the issue of a logging API. It is assumed that a standard log API such as syslog (C), log4j (Java), or logger (Python) is being used. Other custom logging API or even printf could be used. The key point is that the logs must contain the required information in the required format. At a high level of abstraction, the best practices for Grid logging are: (1) Consistently structured, typed, log events; (2) A standard high-resolution timestamp; (3) Use of logging levels and categories to separate logs by detail and purpose; (4) Consistent use of global and local identifiers; and (5) Use of some regular, newline-delimited ASCII text format. The rest of this document describes each of these recommendations in detail.

  19. ULTRA-LIGHTWEIGHT CEMENT

    SciTech Connect (OSTI)

    Fred Sabins

    2003-07-31

    The objective of this project is to develop an improved ultra-lightweight cement using ultra-lightweight hollow glass spheres (ULHS). This report discusses testing that was performed for analyzing the alkali-silica reactivity of ULHS in cement slurries. Laboratory testing during the eleventh quarter focused on evaluation of the alkali-silica reaction of eight different cement compositions, four of which contain ULHS. This report provides a progress summary of ASR testing. The original laboratory procedure for measuring set cement expansion resulted in unacceptable erosion of the test specimens. In subsequent tests, a different expansion procedure was implemented and an alternate curing method for cements formulated with TXI Lightweight cement was employed to prevent sample failure caused by thermal shock. The results obtained with the modified procedure showed improvement over data obtained with the original procedure, but data for some compositions were still questionable. Additional modification of test procedures for compositions containing TXI Lightweight cement were implemented and testing is ongoing.

  20. Category:Chemical Logging | Open Energy Information

    Open Energy Info (EERE)

    Chemical Logging Jump to: navigation, search Geothermalpower.jpg Looking for the Chemical Logging page? For detailed information on Chemical Logging, click here. Category:Chemical...

  1. Geotech Logging Services | Open Energy Information

    Open Energy Info (EERE)

    Logging Services Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: Geotech Logging Services Author Geotech Logging Servces LLC Published Publisher...

  2. Coiled-tubing logging system

    SciTech Connect (OSTI)

    Howell, E.P.; Smith, L.J.; Blount, C.G.

    1988-03-01

    Techniques have been developed to use coiled tubing containing a seven-conductor wireline to facilitate logging operations. Equipment has been designed to permit the connection of conventional logging tools to the tubing and the recording of logs. Operating techniques have been developed and applied under various wellbore conditions. The system allows traditional log measurements in a well while wellbore conditions are controlled. Advantages of the system include reduced wellbore pressure during peroration to maximize perforation performance; lubrication during pulling or pushing a logging tool through a borehole so that a more uniform velocity can be maintained with a logging sonde; continued circulation and thus borehole stability during logging; temperature reduction for improved reliability of logging sonde electronics in hot holes; and more stable positioning of perforation equipment. The ability of coiled tubing to push tools down highly deviated or horizontal wellbores makes logging or perforating feasible in these wells. Expenses can often be reduced with coiled-tubing logging because a rig is unnecessary during many operations.

  3. Coiled-tubing logging system

    SciTech Connect (OSTI)

    Howell, E.P.; Smith, L.J.; Blount, C.G.

    1986-01-01

    Techniques have been developed which use coiled tubing containing a seven-conductor wireline to facilitate logging operations. Equipment has been designed which permits the connection of conventional logging tools to the tubing and the recording of logs. Also, operating techniques have been developed and applied under various wellbore conditions. The system allows traditional log measurements in a well while controlling wellbore conditions. Advantages of the system include: reduced wellbore pressure during perforation to minimize formation damage: lubrication while pulling or pushing a logging tool through a borehole so that a more uniform velocity can be maintained with a logging sonde; continued circulation and thus borehole stability while logging; temperature reduction for improved reliability of logging sonde electronics in hot holes; and more stable positioning of perforation equipment. The ability of coiled tubing to push tools down highly deviated, or even horizontal wellbores, makes logging or perforating feasible in these wells. Expenses can often be reduced with coiled-tubing logging, since a rig is unnecessary during many operations.

  4. Thermodynamics and cement science

    SciTech Connect (OSTI)

    Damidot, D.; Lothenbach, B.; Herfort, D.; Glasser, F.P.

    2011-07-15

    Thermodynamics applied to cement science has proved to be very valuable. One of the most striking findings has been the extent to which the hydrate phases, with one conspicuous exception, achieve equilibrium. The important exception is the persistence of amorphous C-S-H which is metastable with respect to crystalline calcium silicate hydrates. Nevertheless C-S-H can be included in the scope of calculations. As a consequence, from comparison of calculation and experiment, it appears that kinetics is not necessarily an insuperable barrier to engineering the phase composition of a hydrated Portland cement. Also the sensitivity of the mineralogy of the AFm and AFt phase compositions to the presence of calcite and to temperature has been reported. This knowledge gives a powerful incentive to develop links between the mineralogy and engineering properties of hydrated cement paste and, of course, anticipates improvements in its performance leading to decreasing the environmental impacts of cement production.

  5. Category:Neutron Log | Open Energy Information

    Open Energy Info (EERE)

    Looking for the Neutron Log page? For detailed information on Neutron Log, click here. Category:Neutron Log Add.png Add a new Neutron Log Technique Pages in category...

  6. Chemical Logging | Open Energy Information

    Open Energy Info (EERE)

    concentrations.1 Use in Geothermal Exploration During a chemical logging study at the Raft River Geothermal Test Site, returned drilling fluid samples were collected every...

  7. Acoustic paramagnetic logging tool

    DOE Patents [OSTI]

    Vail, III, William B.

    1988-01-01

    New methods and apparatus are disclosed which allow measurement of the presence of oil and water in geological formations using a new physical effect called the Acoustic Paramagnetic Logging Effect (APLE). The presence of petroleum in formation causes a slight increase in the earth's magnetic field in the vicinity of the reservoir. This is the phenomena of paramagnetism. Application of an acoustic source to a geological formation at the Larmor frequency of the nucleons present causes the paramagnetism of the formation to disappear. This results in a decrease in the earth3 s magnetic field in the vicinity of the oil bearing formation. Repetitively frequency sweeping the acoustic source through the Larmor frequency of the nucleons present (approx. 2 kHz) causes an amplitude modulation of the earth's magnetic field which is a consequence of the APLE. The amplitude modulation of the earth's magnetic field is measured with an induction coil gradiometer and provides a direct measure of the amount of oil and water in the excitation zone of the formation . The phase of the signal is used to infer the longitudinal relaxation times of the fluids present, which results in the ability in general to separate oil and water and to measure the viscosity of the oil present. Such measurements may be preformed in open boreholes and in cased well bores.

  8. FOIA Log 2013.xlsx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Rec'd Requestor HQ, EMCBC or Direct Subject 2/12/13 e-mail to HQ 13-001 10/4/2012 2/4/2013 Jehan Patterson HQ Rec'd 02/01/2013 Ten Categories of Records Since January 1, 2011 Related to DOE Computer Networks (HQ-2012-00062-F/Jehan Patterson) 3/5/13 13-025 13-002 3/5/2013 3/4/2013 Kacee Jackson Direct Request for Buyer Information for Any Buyers, Contracting Officers, or Credit Card Holders 8/6/13 e-mail to CBFO 13-003 7/31/2013 7/31/2013 Mary Grant Direct Miller Act Bond Copy Request for the

  9. ULTRA-LIGHTWEIGHT CEMENT

    SciTech Connect (OSTI)

    Fred Sabins

    2001-10-23

    The objective of this project is to develop an improved ultra-lightweight cement using ultra-lightweight hollow glass spheres (ULHS). Work reported herein addresses tasks performed in the fourth quarter as well as the other three quarters of the past year. The subjects that were covered in previous reports and that are also discussed in this report include: Analysis of field laboratory data of active cement applications from three oil-well service companies; Preliminary findings from a literature review focusing on problems associated with ultra-lightweight cements; Summary of pertinent information from Russian ultra-lightweight cement literature review; and Comparison of compressive strengths of ULHS systems using ultrasonic and crush methods Results reported from the fourth quarter include laboratory testing of ULHS systems along with other lightweight cement systems--foamed and sodium silicate slurries. These comparison studies were completed for two different densities (10.0 and 11.5 lb/gal) and three different field application scenarios. Additional testing included the mechanical properties of ULHS systems and other lightweight systems. Studies were also performed to examine the effect that circulation by centrifugal pump during mixing has on breakage of ULHS.

  10. ULTRA-LIGHTWEIGHT CEMENT

    SciTech Connect (OSTI)

    Fred Sabins

    2003-06-16

    The objective of this project is to develop an improved ultra-lightweight cement using ultra-lightweight hollow glass spheres (ULHS). This report discusses testing that was performed for analyzing the alkali-silica reactivity of ULHS in cement slurries. Laboratory testing during the tenth quarter focused on evaluation of the alkali-silica reaction of eight different cement compositions, four of which contain ULHS. The original laboratory procedure for measuring set cement expansion resulted in test specimen erosion that was unacceptable. A different expansion procedure is being evaluated. This report provides a progress summary of ASR testing. The testing program initiated in November produced questionable initial results so the procedure was modified slightly and the testing was reinitiated. The results obtained with the modified procedure showed improvement over data obtained with the original procedure, but questionable data were obtained from several of the compositions. Additional modification of test procedures for compositions containing TXI Lightweight cement are being implemented and testing is ongoing.

  11. A new approach for deriving pseudovelocity logs from resistivity logs

    SciTech Connect (OSTI)

    Dos Santos, W.L.B.; Ulrych, T.J.; De Lima, O.A.L.

    1988-01-01

    This paper describes a method of generating pseudovelocity logs using measurements of electrical resistivity. A theoretical relation between electrical resistivity and transit time, which is applicable to a wide range of lithologies, has been developed. The application of this relation using a method which defines lithoresistivity zones as lithological intervals related to the same formation and showing small resistivity variations, has been tested in the Reconcavo sedimentary basin in Bahia, Brazil. A comparison of derived pseudovelocity logs with actual sonic logs for five wells shows the validity of the present approach.

  12. Category:Well Log Techniques | Open Energy Information

    Open Energy Info (EERE)

    1 pages C Caliper Log 1 pages Chemical Logging 1 pages D Density Log 1 pages G Gamma Log 1 pages I Image Logs 1 pages M Mud...

  13. High temperature lightweight foamed cements

    DOE Patents [OSTI]

    Sugama, Toshifumi

    1989-01-01

    Cement slurries are disclosed which are suitable for use in geothermal wells since they can withstand high temperatures and high pressures. The formulation consists of cement, silica flour, water, a retarder, a foaming agent, a foam stabilizer, and a reinforcing agent. A process for producing these cements is also disclosed.

  14. High temperature lightweight foamed cements

    DOE Patents [OSTI]

    Sugama, Toshifumi.

    1989-10-03

    Cement slurries are disclosed which are suitable for use in geothermal wells since they can withstand high temperatures and high pressures. The formulation consists of cement, silica flour, water, a retarder, a foaming agent, a foam stabilizer, and a reinforcing agent. A process for producing these cements is also disclosed. 3 figs.

  15. Well Log Techniques | Open Energy Information

    Open Energy Info (EERE)

    formation properties versus depth in a borehole. Other definitions:Wikipedia Reegle Introduction Well logging, also known as wireline logging, is a method of data collection in the...

  16. Vertical Flowmeter Logging | Open Energy Information

    Open Energy Info (EERE)

    Logging Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: Vertical Flowmeter Logging Author U.S. Geological Survey Published USGS Groundwater...

  17. Cement (2010 MECS) | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Cement (2010 MECS) Cement (2010 MECS) Manufacturing Energy and Carbon Footprint for Cement Sector (NAICS 327310) Energy use data source: 2010 EIA MECS (with adjustments) Footprint Last Revised: February 2014 View footprints for other sectors here. Manufacturing Energy and Carbon Footprint Cement (126.44 KB) More Documents & Publications MECS 2006 - Cement Glass and Glass Products (2010 MECS) Textiles

  18. US cement industry

    SciTech Connect (OSTI)

    Nisbet, M.A.

    1997-12-31

    This paper describes the cement and concrete industry, and provides data on energy use and carbon dioxide emissions. The potential impact of an energy tax on the industry is briefly assessed. Opportunities identified for reducing carbon dioxide emissions include improved energy efficiency, alternative fuels, and alternative materials. The key factor in determining CO{sub 2} emissions is the level of domestic production. The projected improvement in energy efficiency and the relatively slow growth in domestic shipments indicate that CO{sub 2} emissions in 2000 should be about 5% above the 1990 target. However, due to the cyclical nature of cement demand, emissions will probably be above target levels during peak demand and below target levels during demand troughs. 7 figs., 2 tabs.

  19. Shut-off of a geopressured water channel behind casing via coiled tubing utilizing a dual slurry cement system: A case history

    SciTech Connect (OSTI)

    Nowak, T.W.; Lange, K.J.; Grant, W.H.; Patout, T.S.

    1995-12-31

    This paper presents a case history involving a unique dual cement system to shut off a geopressured water channel behind casing utilizing coiled tubing. The channeling problem was identified and documented using water flow logging techniques. Logging indicated the lower gravel packed selective could produce salt water if perforated without eliminating the suspected water channel. Reserves did not warrant a major rig workover, making a non-rig workover via coiled tubing the only viable option to repair the well. A unique dual cement system tested on a hesitation squeeze schedule pumped through coiled tubing with extremely limited thickening time was necessary to repair the primary cement job.

  20. Well Log Techniques At Raft River Geothermal Area (1977) | Open...

    Open Energy Info (EERE)

    the rock using well log data. Notes Information is given on the following logs: dual-induction focused log, including resistivity, sp, and conductivity; acoustic log; compensated...

  1. Novel Chemically-Bonded Phosphate Ceramic Borehole Sealants (Ceramicretes) for Arctic Environments

    SciTech Connect (OSTI)

    Shirish Patil; Godwin A. Chukwu; Gang Chen; Santanu Khataniar

    2008-12-31

    Novel chemically bonded phosphate ceramic borehole sealant, i.e. Ceramicrete, has many advantages over conventionally used permafrost cement at Alaska North Slope (ANS). However, in normal field practices when Ceramicrete is mixed with water in blenders, it has a chance of being contaminated with leftover Portland cement. In order to identify the effect of Portland cement contamination, recent tests have been conducted at BJ services in Tomball, TX as well as at the University of Alaska Fairbanks with Ceramicrete formulations proposed by the Argonne National Laboratory. The tests conducted at BJ Services with proposed Ceramicrete formulations and Portland cement contamination have shown significant drawbacks which has caused these formulations to be rejected. However, the newly developed Ceramicrete formulation at the University of Alaska Fairbanks has shown positive results with Portland cement contamination as well as without Portland cement contamination for its effective use in oil well cementing operations at ANS.

  2. Thermal Shock-resistant Cement

    SciTech Connect (OSTI)

    Sugama T.; Pyatina, T.; Gill, S.

    2012-02-01

    We studied the effectiveness of sodium silicate-activated Class F fly ash in improving the thermal shock resistance and in extending the onset of hydration of Secar #80 refractory cement. When the dry mix cement, consisting of Secar #80, Class F fly ash, and sodium silicate, came in contact with water, NaOH derived from the dissolution of sodium silicate preferentially reacted with Class F fly ash, rather than the #80, to dissociate silicate anions from Class F fly ash. Then, these dissociated silicate ions delayed significantly the hydration of #80 possessing a rapid setting behavior. We undertook a multiple heating -water cooling quenching-cycle test to evaluate the cement’s resistance to thermal shock. In one cycle, we heated the 200 and #61616;C-autoclaved cement at 500 and #61616;C for 24 hours, and then the heated cement was rapidly immersed in water at 25 and #61616;C. This cycle was repeated five times. The phase composition of the autoclaved #80/Class F fly ash blend cements comprised four crystalline hydration products, boehmite, katoite, hydrogrossular, and hydroxysodalite, responsible for strengthening cement. After a test of 5-cycle heat-water quenching, we observed three crystalline phase-transformations in this autoclaved cement: boehmite and #61614; and #61543;-Al2O3, katoite and #61614; calcite, and hydroxysodalite and #61614; carbonated sodalite. Among those, the hydroxysodalite and #61614; carbonated sodalite transformation not only played a pivotal role in densifying the cementitious structure and in sustaining the original compressive strength developed after autoclaving, but also offered an improved resistance of the #80 cement to thermal shock. In contrast, autoclaved Class G well cement with and without Class F fly ash and quartz flour failed this cycle test, generating multiple cracks in the cement. The major reason for such impairment was the hydration of lime derived from the dehydroxylation of portlandite formed in the autoclaved

  3. Gujarat Ambuja Cements Limited | Open Energy Information

    Open Energy Info (EERE)

    Limited Jump to: navigation, search Name: Gujarat Ambuja Cements Limited Place: Mumbai, India Zip: 400 021 Sector: Biomass Product: Indian cement company. the company...

  4. Rigless multizone recompletion using a cement packer placed with coiled tubing: A case history

    SciTech Connect (OSTI)

    Nowak, T.W.; Patout, T.S.

    1997-12-01

    Cement packers have been used for some time when reserve estimates have not justified the cost of major rig remedial work. They typically provide a means of zonal isolation of the last reserves in an existing wellbore. The success of these operations has historically been low. This is predominantly because of poor cement bonding in the annulus between the tubing and production casing. Because of the minimal amount of equipment on location and lack of upfront design work involved, most cement packers are doomed to failure before they are even placed. Cement packers have been placed using a large number of methods. In the Ship Shoal 181 field, Well B-4 would not economically justify a major rig workover, even though there were several uphole gas sands capable of producing in this well. With proper upfront planning and design, it would be economical; however, all these reserves could be produced in a through-tubing process using a cement packer. This case history presents a refined look at existing technology involving placement of a cement packer and reviews problems common to cement-packer completions, including a case history. Solutions are also discussed for successfully completing and recovering reserves from not one but several remaining gas intervals. This paper reviews the design considerations and precautions, along with the production results and economics, for placing what is believed to be the largest cement packer placed through coiled tubing.

  5. Chemical logging of geothermal wells

    DOE Patents [OSTI]

    Allen, Charles A.; McAtee, Richard E.

    1981-01-01

    The presence of geothermal aquifers can be detected while drilling in geothermal formations by maintaining a chemical log of the ratio of the concentrations of calcium to carbonate and bicarbonate ions in the return drilling fluid. A continuous increase in the ratio of the concentrations of calcium to carbonate and bicarbonate ions is indicative of the existence of a warm or hot geothermal aquifer at some increased depth.

  6. Chemical logging of geothermal wells

    DOE Patents [OSTI]

    Allen, C.A.; McAtee, R.E.

    The presence of geothermal aquifers can be detected while drilling in geothermal formations by maintaining a chemical log of the ratio of the concentrations of calcium to carbonate and bicarbonate ions in the return drilling fluid. A continuous increase in the ratio of the concentrations of calcium to carbonate and bicarbonate ions is indicative of the existence of a warm or hot geothermal aquifer at some increased depth.

  7. BREAKING BOND

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    BREAKING BOND the Can chemistry help unbind us from fossil fuels? 1663 July 2016 21 When ... Their goal: to use chemistry to construct gasoline-like hydrocarbons from plant sugars. ...

  8. Borehole Geophysical Logging | Open Energy Information

    Open Energy Info (EERE)

    Logging Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: Borehole Geophysical Logging Authors Hager-Richter Geoscience and Inc. Published Publisher Not...

  9. Energy Citations Database (ECD) - Alerts Log On

    Office of Scientific and Technical Information (OSTI)

    Log On You must Log On to use the ECD Alerts. Alerts provide users with e-mail notification of updates to the ECD in specific areas of interest. If you wish to receive an Alert and...

  10. Cement Creek Ranch Pool & Spa Low Temperature Geothermal Facility...

    Open Energy Info (EERE)

    Cement Creek Ranch Pool & Spa Low Temperature Geothermal Facility Jump to: navigation, search Name Cement Creek Ranch Pool & Spa Low Temperature Geothermal Facility Facility Cement...

  11. Leak checker data logging system

    DOE Patents [OSTI]

    Gannon, J.C.; Payne, J.J.

    1996-09-03

    A portable, high speed, computer-based data logging system for field testing systems or components located some distance apart employs a plurality of spaced mass spectrometers and is particularly adapted for monitoring the vacuum integrity of a long string of a superconducting magnets such as used in high energy particle accelerators. The system provides precise tracking of a gas such as helium through the magnet string when the helium is released into the vacuum by monitoring the spaced mass spectrometers allowing for control, display and storage of various parameters involved with leak detection and localization. A system user can observe the flow of helium through the magnet string on a real-time basis hour the exact moment of opening of the helium input valve. Graph reading can be normalized to compensate for magnet sections that deplete vacuum faster than other sections between testing to permit repetitive testing of vacuum integrity in reduced time. 18 figs.

  12. Leak checker data logging system

    DOE Patents [OSTI]

    Gannon, Jeffrey C.; Payne, John J.

    1996-01-01

    A portable, high speed, computer-based data logging system for field testing systems or components located some distance apart employs a plurality of spaced mass spectrometers and is particularly adapted for monitoring the vacuum integrity of a long string of a superconducting magnets such as used in high energy particle accelerators. The system provides precise tracking of a gas such as helium through the magnet string when the helium is released into the vacuum by monitoring the spaced mass spectrometers allowing for control, display and storage of various parameters involved with leak detection and localization. A system user can observe the flow of helium through the magnet string on a real-time basis hour the exact moment of opening of the helium input valve. Graph reading can be normalized to compensate for magnet sections that deplete vacuum faster than other sections between testing to permit repetitive testing of vacuum integrity in reduced time.

  13. Diffusion bonding

    DOE Patents [OSTI]

    Anderson, Robert C.

    1976-06-22

    1. A method for joining beryllium to beryllium by diffusion bonding, comprising the steps of coating at least one surface portion of at least two beryllium pieces with nickel, positioning a coated surface portion in a contiguous relationship with an other surface portion, subjecting the contiguously disposed surface portions to an environment having an atmosphere at a pressure lower than ambient pressure, applying a force upon the beryllium pieces for causing the contiguous surface portions to abut against each other, heating the contiguous surface portions to a maximum temperature less than the melting temperature of the beryllium, substantially uniformly decreasing the applied force while increasing the temperature after attaining a temperature substantially above room temperature, and maintaining a portion of the applied force at a temperature corresponding to about maximum temperature for a duration sufficient to effect the diffusion bond between the contiguous surface portions.

  14. California-Nevada uranium logging. Final report

    SciTech Connect (OSTI)

    Not Available

    1981-04-01

    The purpose of this project was to obtain geophysical logs of industry drill holes to assess the uranium resource potential of geologic formations of interest. The work was part of the US Department of Energy's National Uranium Resource Evaluation (NURE) Program. The principal objective of the logging program was to determine radioelement grade of formations through natural gamma ray detectors. Supplementary information was obtained from resistivity (R), self-potential (SP), point resistance (RE), and neutron density (NN) logs for formation interpretation. Additional data for log interpretation was obtained from caliper logs, casing schedules, and downhole temperature. This data was obtained from well operators when available, with new logs obtained where not formerly available. This report contains a summary of the project and data obtained to date.

  15. ADVANCED CEMENTS FOR GEOTHERMAL WELLS

    SciTech Connect (OSTI)

    SUGAMA,T.

    2007-01-01

    Using the conventional well cements consisting of the calcium silicate hydrates (CaO-SiO{sub 2}-H{sub 2}O system) and calcium aluminum silicate hydrates (CaO-Al{sub 2}O{sub 3}-SiO{sub 2}-H{sub 2}O system) for the integrity of geothermal wells, the serious concern confronting the cementing industries was their poor performance in mechanically supporting the metallic well casing pipes and in mitigating the pipe's corrosion in very harsh geothermal reservoirs. These difficulties are particularly acute in two geological regions: One is the deep hot downhole area ({approx} 1700 m depth at temperatures of {approx} 320 C) that contains hyper saline water with high concentrations of CO{sub 2} (> 40,000 ppm) in conjunction with {approx} 100 ppm H{sub 2}S at a mild acid of pH {approx} 5.0; the other is the upper well region between the well's surface and {approx} 1000 m depth at temperatures up to 200 C. The specific environment of the latter region is characterized by highly concentrated H{sub 2}SO{sub 4} (pH < 1.5) brine containing at least 5000 ppm CO{sub 2}. When these conventional cements are emplaced in these harsh environments, their major shortcoming is their susceptibility to reactions with hot CO{sub 2} and H{sub 2}SO4, thereby causing their deterioration brought about by CO{sub 2}-catalyzed carbonation and acid-initiated erosion. Such degradation not only reduced rapidly the strength of cements, lowering the mechanical support of casing pipes, but also increased the extent of permeability of the brine through the cement layer, promoting the rate of the pipe's corrosion. Severely carbonated and acid eroded cements often impaired the integrity of a well in less than one year; in the worst cases, casings have collapsed within three months, leading to the need for costly and time-consuming repairs or redrilling operations. These were the reasons why the geothermal well drilling and cementing industries were concerned about using conventional well cements, and further

  16. Effects of depositional facies and diagenesis on calculating petrophysical properties for wireline logs in Permian carbonate reservoirs of west Texas

    SciTech Connect (OSTI)

    Holtz, M.H.; Major, R.P. )

    1994-03-01

    The complex interplay between depositional facies and diagenesis in carbonate rocks presents numerous problems for calculating petrophysical properties from wireline logs. If carbonate reservoirs are divided into flow units of similar depositional and diagenetic textures, empirical equations that apply specifically to that geologically identified flow unit can be developed to accurately measure porosity and water saturation. In Guadalupian and Leonardian reservoirs, carbonate mudstones deposited in subtidal marine settings are predominantly dolomite, although they contain some shale. The shale in these rocks can be detected with gamma-ray logs and empirical equations for calculation of porosity from log must include a gamma-ray component to compensate for the presence of shale. Because porosity in these rocks is dominantly intercrystalline, capillary pressure characteristics are predictable and saturations can be calculated with the Archie equation. Subtidal carbonate packstones and grainstones are composed of dolomite, anhydrite, and gypsum. The matrix acoustic transit times of these three minerals are similar, and acoustic logs are the best tool for measuring porosity. Neutron logs are the least accurate porosity tools if gypsum is present. Photo-electric density logs can distinguish gypsum from anhydrite. Because porosity in these rocks is dominantly interparticle and/or moldic, dual porosity cementation exponent corrections are needed to calculate saturations with the Archie equation, and capillary pressure saturation relationships are variable. Carbonates deposited in tidal-flat environments are generally composed of dolomite, sulfate minerals, and quartz silt, requiring a full suite of open-hole logs to make reliable porosity measurements. Diagenesis influences reservoir mineralogy and pore types. A common style of burial diagenesis in Guadalupian and Leonardian reservoirs is hydration of anhydrite to gypsum and leaching of sulfate cement and dolomite matrix.

  17. Proven logging technology for high temperatures

    SciTech Connect (OSTI)

    Gonzalez, M.E.

    1995-12-01

    Los Alamos National Laboratory (LANL) hot-hole logging technology for geothermal projects was retrofitted into cased-hole logging tools (gamma ray, neutron and casing collar) for use in deep gas wells. Lab tests indicated that hot-hole tools would last three times longer at 400 F (204 C) bottomhole conditions. During logging runs in Western Oklahoma, Beckham County deep gas wells, standard cased-hole logging tools failed in two to four hours, but hot-hole tools ran successfully for two consecutive six-hour logging runs (12 hours). Subsequent to this, retrofitted tools were equally effective in South Texas and Wyoming. This paper reviews results and design of this equipment.

  18. Method of the cementing of material

    SciTech Connect (OSTI)

    Konovalov, Y.G.; Shutov, G.M.; Khanenya, G.P.; Dyatko, E.K.; Buben, K.K.

    1990-10-30

    Invention relates to woodworking industry and concerns method of cementing of materials of foam plastic with duralumin, glued plywood, etc. Known methods of cementing of materials by effect of electromagnetic field of superhigh frequencies are unproductive and do not make it possible to cement parts on the plane. Target of invention - acceleration of process of cementing of planar, including of complex configuration, parts and assemblies from wood, foam plastic, duralumin, glued plywood and other materials. For this material is cemented under the effect of directed electromagnetic field of superhigh frequency in the range 01-50 GHz, the specific power of 0.5-15 W/cm3.

  19. Process for cementing geothermal wells

    DOE Patents [OSTI]

    Eilers, Louis H.

    1985-01-01

    A pumpable slurry of coal-filled furfuryl alcohol, furfural, and/or a low molecular weight mono- or copolymer thereof containing, preferably, a catalytic amount of a soluble acid catalyst is used to cement a casing in a geothermal well.

  20. Sedimentological analysis using geophysical well logs

    SciTech Connect (OSTI)

    Izotova, T.S. )

    1993-09-01

    The application of geophysical well logs in sedimentology and stratigraphic prospecting holds great promise in solving a number of geological problems. A suite of logs provides data on a wide range of rock properties: vertical and lateral variation of resistivity, natural polarization, natural and induced radioactivity, shear strength, and acoustic properties. Each of these properties is controlled by the depositional environment of the sediments and their later diagenesis. The attention of geologists and geophysicists is drawn to new techniques in the interpretation of geophysical well logs for exploration, appraisal, and development of oil and gas fields. The relationship between geophysical logs and depositional environments is explored. Bulk composition, rock structure, and texture and facies variation can be quantified by electric log parameters. Also, the possibility of using logs to demonstrate long- and short-period sedimentary cycles is demonstrated. Methods of sedimentological analysis using geophysical well logs are demonstrated. The importance of a genetic approach in the interpretation of geological sequences and paleogeological reconstructions is emphasized using examples taken from oil and gas prospecting operations in the Ukraine.

  1. Logging in to Cori P1

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Logging in Logging in to Cori P1 Interactive Access You can log in to Cori using SSH (Secure Shell) with the following command from any UNIX, Mac OS X, Linux, FreeBSD, etc. command shell or terminal: ssh -l username cori.nersc.gov There are several SSH-capable clients available for Windows, Mac, and UNIX/Linux machines. NERSC does not support or recommend any particular client. More information on connecting to NERSC with SSH, including how to generate SSH keys for passworless logins, can be

  2. CMLOG: A common message logging system

    SciTech Connect (OSTI)

    Chen, J.; Akers, W.; Bickley, M.; Wu, D.; Watson, W. III

    1997-12-01

    The Common Message Logging (CMLOG) system is an object-oriented and distributed system that not only allows applications and systems to log data (messages) of any type into a centralized database but also lets applications view incoming messages in real-time or retrieve stored data from the database according to selection rules. It consists of a concurrent Unix server that handles incoming logging or searching messages, a Motif browser that can view incoming messages in real-time or display stored data in the database, a client daemon that buffers and sends logging messages to the server, and libraries that can be used by applications to send data to or retrieve data from the database via the server. This paper presents the design and implementation of the CMLOG system meanwhile it will also address the issue of integration of CMLOG into existing control systems.

  3. Sisyphus - An Event Log Analysis Toolset

    Energy Science and Technology Software Center (OSTI)

    2004-09-01

    Event logs are a ubiquitous source of system feedback from computer systems, but have widely ranging format and can be extremely numerous, particularly from systems with many logging components. Inspection of these logs is fundamental to system debugging; increased capability to quickly extract meaningful information will impact MTTR (mean time to repair) and may impact MTBF (mean time between failure). Sisyphus is a machine-leanring analysis system whose goal is to enable content-novice analysts to efficieniiymore » understand evolving trends, identify anomalies, and investigate cause-effect hypotheses in large multiple-souce log sets. The toolkit is comprised a framework for utilizing third-party frequentitemset data mining tools Teiresias and SLCT. and software to cluster messages according to time statistics, and an interactive results viewer.« less

  4. Logs Wood Chips Straw Corn Switchgrass

    Broader source: Energy.gov (indexed) [DOE]

    Clean energy can come from the sun. The energy in wind can make electricity. Bioenergy comes from plants we can turn into fuel. Logs Wood Chips Straw Corn Switchgrass We can use ...

  5. Formation mechanical properties and the sonic log

    SciTech Connect (OSTI)

    Elphick, R.Y.

    1988-11-01

    A program is presented that calculates the mechanical properties of reservoir rocks from sonic logs. The program was written in Microsoft BASIC and the source code for MS-DOS, Apple Macintosh, and Amiga personal computers is given.

  6. Logging-while-coring method and apparatus

    DOE Patents [OSTI]

    Goldberg, David S.; Myers, Gregory J.

    2007-01-30

    A method and apparatus for downhole coring while receiving logging-while-drilling tool data. The apparatus includes core collar and a retrievable core barrel. The retrievable core barrel receives core from a borehole which is sent to the surface for analysis via wireline and latching tool The core collar includes logging-while-drilling tools for the simultaneous measurement of formation properties during the core excavation process. Examples of logging-while-drilling tools include nuclear sensors, resistivity sensors, gamma ray sensors, and bit resistivity sensors. The disclosed method allows for precise core-log depth calibration and core orientation within a single borehole, and without at pipe trip, providing both time saving and unique scientific advantages.

  7. Logging-while-coring method and apparatus

    DOE Patents [OSTI]

    Goldberg, David S.; Myers, Gregory J.

    2007-11-13

    A method and apparatus for downhole coring while receiving logging-while-drilling tool data. The apparatus includes core collar and a retrievable core barrel. The retrievable core barrel receives core from a borehole which is sent to the surface for analysis via wireline and latching tool The core collar includes logging-while-drilling tools for the simultaneous measurement of formation properties during the core excavation process. Examples of logging-while-drilling tools include nuclear sensors, resistivity sensors, gamma ray sensors, and bit resistivity sensors. The disclosed method allows for precise core-log depth calibration and core orientation within a single borehole, and without at pipe trip, providing both time saving and unique scientific advantages.

  8. Energy Citations Database (ECD) - Alerts Log On

    Office of Scientific and Technical Information (OSTI)

    ECD Alerts Log On Alerts provide users with e-mail notification of updates to the ECD in specific areas of interest. If you wish to receive an Alert and are not registered, please...

  9. Property:FirstWellLog | Open Energy Information

    Open Energy Info (EERE)

    FirstWellLog Jump to: navigation, search Property Name FirstWellLog Property Type Page Retrieved from "http:en.openei.orgwindex.php?titleProperty:FirstWellLog&oldid598766...

  10. Category:Pressure Temperature Log | Open Energy Information

    Open Energy Info (EERE)

    Geothermalpower.jpg Looking for the Pressure Temperature Log page? For detailed information on Pressure Temperature Log, click here. Category:Pressure Temperature Log Add.png Add a...

  11. Category:Cross-Dipole Acoustic Log | Open Energy Information

    Open Energy Info (EERE)

    Cross-Dipole Acoustic Log Jump to: navigation, search Geothermalpower.jpg Looking for the Cross-Dipole Acoustic Log page? For detailed information on Cross-Dipole Acoustic Log,...

  12. High Temperature Cements | Open Energy Information

    Open Energy Info (EERE)

    gles":,"locations":"text":"Cement for...

  13. Squeeze cement method using coiled tubing

    SciTech Connect (OSTI)

    Underdown, D.R.; Ashford, J.D.; Harrison, T.W.; Eastlack, J.K.; Blount, C.G.; Herring, G.D.

    1986-12-09

    A method is described of squeeze cementing a well wherein the well has a casing throughout the wellbore, casing cement between the casing and the wellbore of the well, perforations through the casing and the casing cement to establish fluid communication between the interior of the casing and a formation adjacent the perforations, channels in the casing cement in fluid communication with at least some of the perforations, a well tubing string in the casing extending from the surface to the proximity of the perforations, and a packer means for sealing between the tubing and the casing above the perforations. The method consists of: isolating the casing adjacent the perforations; lowering a coiled tubing down the well tubing string to a point adjacent the perforations; flowing uncontaminated squeeze cement through the coiled tubing and through the perforations into the channels; flowing a cement contaminating liquid down the coiled tubing to mix with the squeeze cement remaining in the casing; allowing the uncontaminated squeeze cement in the channels to harden; and removing the contaminated squeeze cement from the casing through the coiled tubing.

  14. Pressure Temperature Log At Vale Hot Springs Area (Combs, Et...

    Open Energy Info (EERE)

    Unknown Notes Numerous temperature logs were taken with Sandia's platinum-resistance-thermometer (PRT) tool which along with a Sandia logging truck remained on-site for...

  15. Manager's Signature Log Privacy Impact Assessment, Office of...

    Office of Environmental Management (EM)

    Manager's Signature Log Privacy Impact Assessment, Office of Science Chicago Office Manager's Signature Log Privacy Impact Assessment, Office of Science Chicago Office Manager's ...

  16. Energy Efficiency in Log Homes | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    energy efficiency when designing or purchasing a log home. | Photo courtesy of iStockphoto.comtinabelle Consider energy efficiency when designing or purchasing a log home. |...

  17. Green Energy Resources Inc formerly New York International Log...

    Open Energy Info (EERE)

    Inc formerly New York International Log Lumber Company Jump to: navigation, search Name: Green Energy Resources Inc (formerly New York International Log & Lumber Company) Place:...

  18. Preservationists Tour Historic Log Cabin at the Grand Junction...

    Office of Environmental Management (EM)

    Preservationists Tour Historic Log Cabin at the Grand Junction, Colorado, Office Preservationists Tour Historic Log Cabin at the Grand Junction, Colorado, Office April 19, 2016 - ...

  19. COMPARISON OF ACOUSTIC AND ELECTRICAL IMAGE LOGS FROM THE COSO...

    Open Energy Info (EERE)

    image log, but locally approach 100%. This fabric is unlikely to contribute to permeability in the reservoir. Acoustic image logs reveal a similar natural fracture population,...

  20. Chemical Logging At North Brawley Geothermal Area (Department...

    Open Energy Info (EERE)

    Chemical logs were made from well fluids for analysis when designing the first experimental power plant Notes Detailed logs of well fluids were recorded. Non-condensable gases...

  1. Logjam: A scalable unified log file archiver

    Energy Science and Technology Software Center (OSTI)

    2001-08-01

    Log files are a necessary record of events on any system. However, as systems scale, so does the volume of data captured. To complicate matters, this data can be distributed across all nodes within the system. This creates challenges in ways to obtain these files as well as archiving them in a consistent manner. It has become commonplace to develop a custom written utility for each system that is tailored specifically to that system. Formore » computer centers that contain multiple systems, each system would have their own respective utility for gathering and archiving log files. Each time a new log file is produced, a modification to the utility is necessary. With each modification, risks of errors could be introduced as well as spending time to introduce that change. This is precisely the purpose of logjam. Once installed, the code only requires modification when new features are required. A configuration file is used to identify each log file as well as where to harvest it and how to archive it. Adding a new log file is as simple as defining it in a configuration file and testing can be performed in the production environment.« less

  2. INFORMAL REPORT PROPERTIES AND PERFORMANCE OF CEMENT- BASED GROUTS...

    Office of Scientific and Technical Information (OSTI)

    ... Cement Ground Heat Exchanger Grouts, ASHRAE Transactions, Vol. 105, Part 1,446-450, ... Cement Ground Heat Exchanger Grouts, ASHRAE Transactions, Vol. 105, Part 1,446-450, ...

  3. Wellbore Integrity Assurance with NETL's Safe Cementing Research

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Contact Us Wellbore cement integrity is paramount to safe, successful oil and natural gas drilling. Cement acts as the primary barrier between the wellbore and the environment....

  4. Multifunctional Corrosion-resistant Foamed Well Cement Composites...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Multifunctional Corrosion-resistant Foamed Well Cement Composites Multifunctional Corrosion-resistant Foamed Well Cement Composites Multifunctional Corrosion-resistant Foamed Well ...

  5. BEST-Cement for China | Open Energy Information

    Open Energy Info (EERE)

    BEST-Cement for China Jump to: navigation, search Tool Summary LAUNCH TOOL Name: BEST-Cement AgencyCompany Organization: Lawrence Berkeley National Laboratory Partner: Energy...

  6. Development of pulsed neutron uranium logging instrument

    SciTech Connect (OSTI)

    Wang, Xin-guang; Liu, Dan; Zhang, Feng

    2015-03-15

    This article introduces a development of pulsed neutron uranium logging instrument. By analyzing the temporal distribution of epithermal neutrons generated from the thermal fission of {sup 235}U, we propose a new method with a uranium-bearing index to calculate the uranium content in the formation. An instrument employing a D-T neutron generator and two epithermal neutron detectors has been developed. The logging response is studied using Monte Carlo simulation and experiments in calibration wells. The simulation and experimental results show that the uranium-bearing index is linearly correlated with the uranium content, and the porosity and thermal neutron lifetime of the formation can be acquired simultaneously.

  7. Logging of subterranean wells using coiled tubing

    SciTech Connect (OSTI)

    Pilla, J.

    1991-01-15

    This patent describes an apparatus for production logging of a well utilizing artificial lift in a wellbore. It comprises: coiled tubing extending into the wellbore having wireline electrical cable passing through a central bore thereof and having a remote end within the wellbore which end is connected to gas injector means. The wireline cable passing through the gas injector means to a flexible electrically conductive support spacer having an end portion remote from the gas injector means and logging means connected to the end portion of the support spacer.

  8. INSPIRE and SPIRES Log File Analysis

    SciTech Connect (OSTI)

    Adams, Cole; /Wheaton Coll. /SLAC

    2012-08-31

    SPIRES, an aging high-energy physics publication data base, is in the process of being replaced by INSPIRE. In order to ease the transition from SPIRES to INSPIRE it is important to understand user behavior and the drivers for adoption. The goal of this project was to address some questions in regards to the presumed two-thirds of the users still using SPIRES. These questions are answered through analysis of the log files from both websites. A series of scripts were developed to collect and interpret the data contained in the log files. The common search patterns and usage comparisons are made between INSPIRE and SPIRES, and a method for detecting user frustration is presented. The analysis reveals a more even split than originally thought as well as the expected trend of user transition to INSPIRE.

  9. Logging while tripping cuts time to run gamma ray

    SciTech Connect (OSTI)

    1996-06-10

    A new logging tool, sent down the drillstring before a pipe trip out of the hole, logs the well as the pipe is pulled from the hole, cutting the total time required for open hole logging on some wells. This logging while tripping (LWT) technology allows an operator to run a gamma ray and neutron log more quickly than with standard wire line equipment. The drill pipe conveys the logging tools up the well as the pipe is tripped out, and the logging data are stored in the tool`s memory. A transparent logging collar, which meets API 7 and RP7G requirements, holds the tools in the drillstring without interfering with the logging measurements.

  10. Trending: Metal Oxo Bonds

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Trending: Metal Oxo Bonds Trending: Metal Oxo Bonds Print Wednesday, 29 May 2013 00:00 Metal oxides are important for scientific and technical applications in a variety of disciplines, including materials science, chemistry, and biology. Highly covalent metal-oxygen multiple bonds (metal oxos) are the building blocks of metal oxides and have a bearing on the oxide's desirable chemical, magnetic, electronic, and thermal properties. The lack of a more sophisticated grasp of bonding in metal oxides

  11. Energy Efficiency in Log Homes | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Design » Types of Homes » Energy Efficiency in Log Homes Energy Efficiency in Log Homes Consider energy efficiency when designing or purchasing a log home. | Photo courtesy of ©iStockphoto.com/tinabelle Consider energy efficiency when designing or purchasing a log home. | Photo courtesy of ©iStockphoto.com/tinabelle Log homes may be site-built or pre-cut in a factory for delivery to the site. Some log home manufacturers can also customize their designs. Before designing or purchasing a

  12. CONTENTS NETL Boasts State-of-the- Art Capabilities for Cement

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Primary Cementing ......17 Nano Impregnated Cement ... 18 CONTACTS Roy ... Nano Impregnated Cement Honolulu-based Oceanit Laboratories Inc., supported by DOE ...

  13. Bonding thermoplastic polymers

    DOE Patents [OSTI]

    Wallow, Thomas I.; Hunter, Marion C.; Krafcik, Karen Lee; Morales, Alfredo M.; Simmons, Blake A.; Domeier, Linda A.

    2008-06-24

    We demonstrate a new method for joining patterned thermoplastic parts into layered structures. The method takes advantage of case-II permeant diffusion to generate dimensionally controlled, activated bonding layers at the surfaces being joined. It is capable of producing bonds characterized by cohesive failure while preserving the fidelity of patterned features in the bonding surfaces. This approach is uniquely suited to production of microfluidic multilayer structures, as it allows the bond-forming interface between plastic parts to be precisely manipulated at micrometer length scales. The bond enhancing procedure is easily integrated in standard process flows and requires no specialized equipment.

  14. Computational fluid dynamics improves liner cementing operation

    SciTech Connect (OSTI)

    Barton, N.A.; Archer, G.L. ); Seymour, D.A. )

    1994-09-26

    The use of computational fluid dynamics (CFD), an analytical tool for studying fluid mechanics, helped plan the successful cementing of a critical liner in a North Sea extended reach well. The results from CFD analysis increased the confidence in the primary cementing of the liner. CFD modeling was used to quantify the effects of increasing the displacement rate and of rotating the liner on the mud flow distribution in the annulus around the liner.

  15. Clean Energy Bond Finance Model: Industrial Development Bonds (IDBs) |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Bond Finance Model: Industrial Development Bonds (IDBs) Clean Energy Bond Finance Model: Industrial Development Bonds (IDBs) Overview of industrial development bonds. Author: Clean Energy and Bond Finance Initiative (CE+BFI) Industrial Development Bonds (IDBs) Fact Sheet More Documents & Publications Reduce Risk, Increase Clean Energy: How States and Cities are Using Old Finance Tools to Scale Up a New Industry Clean Energy and Bond Finance Initiative Financing

  16. Formation Micro-Imager Logs (FMI) | Open Energy Information

    Open Energy Info (EERE)

    Logs (FMI) Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: Formation Micro-Imager Logs (FMI) Author Shakeel Ahmed Published Publisher Not...

  17. Geophysical logging case history of the Raft River geothermal...

    Open Energy Info (EERE)

    logging case history of the Raft River geothermal system, Idaho Jump to: navigation, search OpenEI Reference LibraryAdd to library Report: Geophysical logging case history of the...

  18. Geochemical Mud Logging of geothermal drilling

    SciTech Connect (OSTI)

    Tonani, F.B.; Guidi, M.; Johnson, S.D.

    1988-01-01

    The experience and results described in the present paper were developed over nearly two decades, with a major R&D project around 1980. The expression Geochemical Mud Logging (GML) has ill defined meaning in the geothermal industry, and ought to be specified. We refer here to GML as featuring mud and formation fluid tracer(s) and temperature as the bare essentials and with specified accuracies. Air and water logging are expected to be less demanding with regard to analysis accuracy, but are not discussed in this report. During application of GML to several drill holes with low formation permeabilities and under conditions of high temperature and high mud weight, GML as specified, revealed unexpected influx of formation brine. Such influx was a recurring feature that has been referenced to individual fractures and reflects both fracture size and permeability. As a consequence, continuous or subcontinuous sampling of mud systems appears more cost effective than trying to keep up with cumulative changes of bulk mud composition; although, the latter approach is more sensitive to extremely low rate, steady, inflow of formation fluid into the mud system. It appears, that based on this influx of formation fluid, permeability can be estimated well before mud losses are detected and/or drill strings are stuck. The main advantages of GML are: (1) the capability to assess formation temperature and permeability in nearly real time, resulting in (a) assessments of undisturbed formation and (b) having data in hand for holes lost during drilling operations and (2) being effective under conditions of very high temperatures where electrical logs are very costly and less reliable. Estimated cost for GML is $1500 per day (1982) based on assessments of R&D operations. However, extrapolating to larger scale services and to different operating conditions is indeed difficult. GML cost is probably the only significant point of controversy with regard to GML being a viable evaluation tool.

  19. Qualified Energy Conservation Bonds (QECBs)

    Broader source: Energy.gov [DOE]

    With tax credit bonds, generally the borrower who issues the bond pays back only the principal of the bond, and the bondholder receives federal tax credits in lieu of the traditional bond interest...

  20. Logging Report for April 19th., and 20th., 1994, Temp/CCL Logs of EE-3A

    SciTech Connect (OSTI)

    Anderson, David W.

    1994-04-27

    Two Temperature/Casing-Collar Locator (CCL), logs of EE-3A were performed on April 19th., and 20th., 1994, in an effort to locate fractures where fluid exits the injection wellbore. The first log was run, to serve as background data for comparison to the second log, which was run after a period of injection. The first log was done under static conditions, (with the exceptions of fluid that escaped through the control head during the log, and the continuous venting of the annulus). The log was then repeated the next day, after an approximate six hours of injection, with the Rotojet pump (at a rate of approximately 24 gpm). It was hoped that the short injection period would create anomalies in temperature across fractures, which could be identified by the log. The results however, were less than hoped for. A depth-driven strip chart, recording both load-cell weight, and CCL was run on both logs. Also, it was planed to speed up the logging rate through the zone of 11,700' to 11,790', which was believed to be an area common to premature set-down. After looking at a variety of previously run logs however, it was determined that these set-downs could occur anywhere in the open hole. For this reason we logged the entire open hole, on both logs, at 75 ft., per minute, and experienced no premature set-downs on either log.

  1. Manager's Signature Log Privacy Impact Assessment, Office of Science

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Chicago Office | Department of Energy Manager's Signature Log Privacy Impact Assessment, Office of Science Chicago Office Manager's Signature Log Privacy Impact Assessment, Office of Science Chicago Office Manager's Signature Log Privacy Impact Assessment, Office of Science Chicago Office Manager's Signature Log Privacy Impact Assessment, Office of Science Chicago Office (110.12 KB) More Documents & Publications Integrated Safety Management Workshop Registration, PIA, Idaho National

  2. Microsoft Word - FOIA Log FY 2001.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    1 FOIA - Request Log 1 Closed/ Date No. Dated Date Rec'd HQ or Dir. Subject Yes/ 3/29/01 001 02/01/01 02/01/01 01-0021C Transfer AL Copies of all documents including studies and memoranda, which may identify or consider WIPP site in Carlsbad, NM as a potential site for storage or disposal of spent reactor fuel or high-level radioactive wastes 2. All documents including studies, memoranda, hypothesizing, considering, recommending, or suggesting the WIPP site in NM as an alternative site to the

  3. Microsoft Word - FOIA Log FY 2002.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 FOIA - Request Log 1 Closed/ Date No. Dated Date Rec'd HQ or Dir. Subject Yes/ 1/30/02 001 12/3/02 12/21/02 Richland Transfer Richland Operation Office search for records they located documents originated by the DOE Carlsbad Field Office that may be responsive to Mr. Hongs request. By transfer of this letter they forwarded Mr. Hong request, along with the documents located at Richland to the Carlsbad FOIA Office. CBFO will respond directly to Mr. Hong with a release determination Yes/ 2/13/02

  4. Microsoft Word - FOIA Log FY 2003.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3 FOIA - Request Log 1 Closed/ Date No. Dated Date Rec'd HQ or Dir. Subject Yes/ 11/03/03 001 12/16/02 1/7/03 Transfer from HQ Documentation provided identifying all Waste Isolation Pilot Plant contractors and their sub- contractors, as well as the principals for those entities. Yes 2/20/04 002 12/16/02 1/7/03 Transfer from HQ Documentation provided concerning the following Waste Isolation Pilot Plant related items: 1) Notify as to whether any portion of Westinghouse TRU Solutions work has been

  5. Microsoft Word - FOIA Log FY 2004.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 FOIA - Request Log 1 Closed/ Date No. Dated Date Rec'd HQ or Dir. Subject Yes 02/20/04 001 02/02/04 02/02/04 Direct Copies of my personnel records that are maintained at 401 N. Canal Street in Carlsbad, New Mexico Yes 03/29/04 002 03/24/04 03/29/04 Direct Transferred to HQ Asking for information regarding Gary K. King during DOE Secretary Bill Richardson's administration from 08//18/1998 through 02/20/2001, including: 1. Travel vouchers and official expenditures made by the United States

  6. Microsoft Word - FOIA Log FY 2007.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    7 FOIA - Request Log 1 Closed/ Date No. Dated Date Rec'd HQ or Dir. Subject Finalized 02/08/07 001 10/05/06 01/08/07 Transfer from DOE- EM-CBC Copies of contract modifications, performance evaluations, task orders and task order proposals related to contract AT30-05EW03000 with Navarro Research and Engineering, Inc. Finalized 01/31/07 002 01/11/07 01/11/07 Direct For a copy of contract DE-AC04-95AL89446 for the period of September 1995 through the end of the contract. Also, if not included in

  7. Log amplifier with pole-zero compensation

    DOE Patents [OSTI]

    Brookshier, W.

    1985-02-08

    A logarithmic amplifier circuit provides pole-zero compensation for improved stability and response time over 6-8 decades of input signal frequency. The amplifer circuit includes a first operational amplifier with a first feedback loop which includes a second, inverting operational amplifier in a second feedstock loop. The compensated output signal is provided by the second operational amplifier with the log elements, i.e., resistors, and the compensating capacitors in each of the feedback loops having equal values so that each break point is offset by a compensating break point or zero.

  8. Log amplifier with pole-zero compensation

    DOE Patents [OSTI]

    Brookshier, William

    1987-01-01

    A logarithmic amplifier circuit provides pole-zero compensation for improved stability and response time over 6-8 decades of input signal frequency. The amplifier circuit includes a first operational amplifier with a first feedback loop which includes a second, inverting operational amplifier in a second feedback loop. The compensated output signal is provided by the second operational amplifier with the log elements, i.e., resistors, and the compensating capacitors in each of the feedback loops having equal values so that each break point or pole is offset by a compensating break point or zero.

  9. Cold bond agglomeration of waste oxides for recycling

    SciTech Connect (OSTI)

    D`Alessio, G.; Lu, W.K.

    1996-12-31

    Recycling of waste oxides has been an on-going challenge for integrated steel plants. The majority of these waste oxides are collected from the cleaning systems of ironmaking and steelmaking processes, and are usually in the form of fine particulates and slurries. In most cases, these waste materials are contaminated by oils and heavy metals and often require treatment at a considerable expense prior to landfill disposal. This contamination also limits the re-use or recycling potential of these oxides as secondary resources of reliable quality. However, recycling of some selected wastes in blast furnaces or steelmaking vessels is possible, but first requires agglomeration of the fine particulate by such methods as cold bond briquetting. Cold bond briquetting technology provides both mechanical compacting and bonding (with appropriate binders) of the particulates. This method of recycling has the potential to be economically viable and environmentally sustainable. The nature of the present study is cold bond briquetting of iron ore pellet fines with a molasses-cement-H{sub 2}O binder for recycling in a blast furnace. The inclusion of molasses is for its contribution to the green strength of briquettes. During the curing stage, significant gains in strength may be credited to molasses in the presence of cement. The interactions of cement (and its substitutes), water and molasses and their effects on the properties of the agglomerates during and after various curing conditions were investigated. Tensile strengths of briquettes made in the laboratory and subjected to experimental conditions which simulated the top part of a blast furnace shaft were also examined.

  10. Well Logging Security Initiatives | Y-12 National Security Complex

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Well Logging Security ... Well Logging Security Initiatives The mp4 video format is not supported by this browser. Download video Captions: On Watch as GTRI demonstrates the threat to the security of (oil) well logging systems and outlines the initiatives that are enhancing the security of these sources worldwide

  11. Analysis of CCRL proficiency cements 151 and 152 using the Virtual Cement and Concrete Testing Laboratory

    SciTech Connect (OSTI)

    Bullard, Jeffrey W. . E-mail: jeffrey.bullard@nist.gov; Stutzman, Paul E.

    2006-08-15

    To test the ability of the Virtual Cement and Concrete Testing Laboratory (VCCTL) software to predict cement hydration properties, characterization of mineralogy and phase distribution is necessary. Compositional and textural characteristics of Cement and Concrete Reference Laboratory (CCRL) cements 151 and 152 were determined via scanning electron microscopy (SEM) analysis followed by computer modeling of hydration properties. The general procedure to evaluate a cement is as follows: (1) two-dimensional SEM backscattered electron and X-ray microanalysis images of the cement are obtained, along with a measured particle size distribution (PSD); (2) based on analysis of these images and the measured PSD, three-dimensional microstructures of various water-to-cement ratios are created and hydrated using VCCTL, and (3) the model predictions for degree of hydration under saturated conditions, heat of hydration (ASTM C186), setting time (ASTM C191), and strength development of mortar cubes (ASTM C109) are compared to experimental measurements either performed at NIST or at the participating CCRL proficiency sample evaluation laboratories. For both cements, generally good agreement is observed between the model predictions and the experimental data.

  12. Alternative Fuel for Portland Cement Processing

    SciTech Connect (OSTI)

    Schindler, Anton K; Duke, Steve R; Burch, Thomas E; Davis, Edward W; Zee, Ralph H; Bransby, David I; Hopkins, Carla; Thompson, Rutherford L; Duan, Jingran; Venkatasubramanian, Vignesh; Stephen, Giles

    2012-06-30

    The production of cement involves a combination of numerous raw materials, strictly monitored system processes, and temperatures on the order of 1500 °C. Immense quantities of fuel are required for the production of cement. Traditionally, energy from fossil fuels was solely relied upon for the production of cement. The overarching project objective is to evaluate the use of alternative fuels to lessen the dependence on non-renewable resources to produce portland cement. The key objective of using alternative fuels is to continue to produce high-quality cement while decreasing the use of non-renewable fuels and minimizing the impact on the environment. Burn characteristics and thermodynamic parameters were evaluated with a laboratory burn simulator under conditions that mimic those in the preheater where the fuels are brought into a cement plant. A drop-tube furnace and visualization method were developed that show potential for evaluating time- and space-resolved temperature distributions for fuel solid particles and liquid droplets undergoing combustion in various combustion atmospheres. Downdraft gasification has been explored as a means to extract chemical energy from poultry litter while limiting the throughput of potentially deleterious components with regards to use in firing a cement kiln. Results have shown that the clinkering is temperature independent, at least within the controllable temperature range. Limestone also had only a slight effect on the fusion when used to coat the pellets. However, limestone addition did display some promise in regards to chlorine capture, as ash analyses showed chlorine concentrations of more than four times greater in the limestone infused ash as compared to raw poultry litter. A reliable and convenient sampling procedure was developed to estimate the combustion quality of broiler litter that is the best compromise between convenience and reliability by means of statistical analysis. Multi-day trial burns were conducted

  13. Dual excitation acoustic paramagnetic logging tool

    DOE Patents [OSTI]

    Vail, III, William B.

    1989-01-01

    New methods and apparatus are disclosed which allow measurement of the presence of oil and water in gelogical formations using a new physical effect called the Acoustic Paramagnetic Logging Effect (APLE). The presence of petroleum in formation causes a slight increase in the earth's magnetic field in the vicinity of the reservoir. This is the phenomena of paramagnetism. Application of an acoustic source to a geological formation at the Larmor frequency of the nucleous present causes the paramagnetism of the formation to disappear. This results in a decrease in the earth's magnetic field in the vicinity of the oil bearing formation. Repetitively frequency sweeping the acoustic source through the Larmor frequency of the nucleons present (approx. 2 kHz) causes an amplitude modulation of the earth's magnetic field which is a consequence of the APLE. The amplitude modulation of the earth's magnetic field is measured with an induction coil gradiometer and provides a direct measure of the amount of oil and water in the excitation zone of the formation. The phase of the signal is used to infer the longitudinal relaxation times of the fluids present, which results in the ability in general to separate oil and water and to measure the viscosity of the oil present. Such measurements may be preformed in open boreholes and in cased well bores. The Dual Excitation Acoustic Paramagnetic Logging Tool employing two acoustic sources is also described.

  14. Dual excitation acoustic paramagnetic logging tool

    DOE Patents [OSTI]

    Vail, W.B. III.

    1989-02-14

    New methods and apparatus are disclosed which allow measurement of the presence of oil and water in geological formations using a new physical effect called the Acoustic Paramagnetic Logging Effect (APLE). The presence of petroleum in formation causes a slight increase in the earth's magnetic field in the vicinity of the reservoir. This is the phenomena of paramagnetism. Application of an acoustic source to a geological formation at the Larmor frequency of the nucleons present causes the paramagnetism of the formation to disappear. This results in a decrease in the earth's magnetic field in the vicinity of the oil bearing formation. Repetitively frequency sweeping the acoustic source through the Larmor frequency of the nucleons present (approx. 2 kHz) causes an amplitude modulation of the earth's magnetic field which is a consequence of the APLE. The amplitude modulation of the earth's magnetic field is measured with an induction coil gradiometer and provides a direct measure of the amount of oil and water in the excitation zone of the formation. The phase of the signal is used to infer the longitudinal relaxation times of the fluids present, which results in the ability in general to separate oil and water and to measure the viscosity of the oil present. Such measurements may be performed in open boreholes and in cased well bores. The Dual Excitation Acoustic Paramagnetic Logging Tool employing two acoustic sources is also described. 6 figs.

  15. Dewarless Logging Tool - 1st Generation

    SciTech Connect (OSTI)

    HENFLING,JOSEPH A.; NORMANN,RANDY A.

    2000-08-01

    This report focuses on Sandia National Laboratories' effort to create high-temperature logging tools for geothermal applications without the need for heat shielding. One of the mechanisms for failure in conventional downhole tools is temperature. They can only survive a limited number of hours in high temperature environments. For the first time since the evolution of integrated circuits, components are now commercially available that are qualified to 225 C with many continuing to work up to 300 C. These components are primarily based on Silicon-On-Insulator (SOI) technology. Sandia has developed and tested a simple data logger based on this technology that operates up to 300 C with a few limiting components operating to only 250 C without thermal protection. An actual well log to 240 C without shielding is discussed. The first prototype high-temperature tool measures pressure and temperature using a wire-line for power and communication. The tool is based around the HT83C51 microcontroller. A brief discussion of the background and status of the High Temperature Instrumentation program at Sandia, objectives, data logger development, and future project plans are given.

  16. Bonded semiconductor substrate

    DOE Patents [OSTI]

    Atwater, Jr.; Harry A. , Zahler; James M.

    2010-07-13

    Ge/Si and other nonsilicon film heterostructures are formed by hydrogen-induced exfoliation of the Ge film which is wafer bonded to a cheaper substrate, such as Si. A thin, single-crystal layer of Ge is transferred to Si substrate. The bond at the interface of the Ge/Si heterostructures is covalent to ensure good thermal contact, mechanical strength, and to enable the formation of an ohmic contact between the Si substrate and Ge layers. To accomplish this type of bond, hydrophobic wafer bonding is used, because as the invention demonstrates the hydrogen-surface-terminating species that facilitate van der Waals bonding evolves at temperatures above 600.degree. C. into covalent bonding in hydrophobically bound Ge/Si layer transferred systems.

  17. BONDING ALUMINUM METALS

    DOE Patents [OSTI]

    Noland, R.A.; Walker, D.E.

    1961-06-13

    A process is given for bonding aluminum to aluminum. Silicon powder is applied to at least one of the two surfaces of the two elements to be bonded, the two elements are assembled and rubbed against each other at room temperature whereby any oxide film is ruptured by the silicon crystals in the interface; thereafter heat and pressure are applied whereby an aluminum-silicon alloy is formed, squeezed out from the interface together with any oxide film, and the elements are bonded.

  18. Trending: Metal Oxo Bonds

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Trending: Metal Oxo Bonds Print Metal oxides are important for scientific and technical applications in a variety of disciplines, including materials science, chemistry, and biology. Highly covalent metal-oxygen multiple bonds (metal oxos) are the building blocks of metal oxides and have a bearing on the oxide's desirable chemical, magnetic, electronic, and thermal properties. The lack of a more sophisticated grasp of bonding in metal oxides constitutes a roadblock to innovation in a wide

  19. Trending: Metal Oxo Bonds

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and technical applications in a variety of disciplines, including materials science, chemistry, and biology. Highly covalent metal-oxygen multiple bonds (metal oxos) are the...

  20. Trending: Metal Oxo Bonds

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    in both in technological and biological processes that are often governed by careful control over the physical and chemical properties of metal-oxygen bonds. For example,...

  1. Microsoft Word - FOIA Log FY 2005.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    5 FOIA - Request Log 1 Closed/ Date No. Dated Date Rec'd HQ or Dir. Subject Yes 02/23/05 001 02/16/05 02/16/05 Direct Copies of the 2004 Modifications to the Westinghouse TRU Solutions contract (No. DE-AC- 04-01AL66444) for the management and operation of the Waste Isolation Pilot Plant. Yes 04/12/05 002 04/11/05 04/11/05 Direct Copies of the scope of work statement for the EE&G Oversight contract for the Waste Isolation Pilot Plant, dated 1999 or 2000 Yes 04/29/05 003 04/20/05 04/20/05

  2. Development of an Improved Cement for Geothermal Wells

    Broader source: Energy.gov [DOE]

    DOE Geothermal Peer Review 2010 - Presentation. Project objectives: Develop a novel, zeolite-containing lightweight, high temperature, high pressure geothermal cement, which will provide operators with an easy to use, flexible cementing system that saves time and simplifies logistics.

  3. Qualified Energy Conservation Bonds

    Broader source: Energy.gov [DOE]

    A Qualified Energy Conservation Bond (QECB) is a bond that enables qualified state, tribal, and local government issuers to borrow money at attractive rates to fund energy conservation projects (it is important to note that QECBs are not grants). A QECB is among the lowest-cost public financing tools because the U.S. Department of the Treasury subsidizes the issuer's borrowing costs.

  4. High temperature expanding cement composition and use

    DOE Patents [OSTI]

    Nelson, Erik B.; Eilers, Louis H.

    1982-01-01

    A hydratable cement composition useful for preparing a pectolite-containing expanding cement at temperatures above about 150.degree. C. comprising a water soluble sodium salt of a weak acid, a 0.1 molar aqueous solution of which salt has a pH of between about 7.5 and about 11.5, a calcium source, and a silicon source, where the atomic ratio of sodium to calcium to silicon ranges from about 0.3:0.6:1 to about 0.03:1:1; aqueous slurries prepared therefrom and the use of such slurries for plugging subterranean cavities at a temperature of at least about 150.degree. C. The invention composition is useful for preparing a pectolite-containing expansive cement having about 0.2 to about 2 percent expansion, by volume, when cured at at least 150.degree. C.

  5. Multifunctional Corrosion-resistant Foamed Well Cement Composites

    Broader source: Energy.gov [DOE]

    Multifunctional Corrosion-resistant Foamed Well Cement Composites presentation at the April 2013 peer review meeting held in Denver, Colorado.

  6. Wellbore Cement: Research That Begins Where the Sidewalk Ends

    Broader source: Energy.gov [DOE]

    As we meander down the sidewalk, how many of us give more than a passing thought to the cement underfoot? Researchers at the National Energy Technology Laboratory think about deteriorating cement a lot, with an aim to preserving its character and protecting the environment. But they’re not looking at sidewalks. Their focus is wellbore cement, the cement encasing pipes that bring oil and gas up to the surface.

  7. Development of an Improved Cement for Geothermal Wells

    Broader source: Energy.gov [DOE]

    Development of an Improved Cement for Geothermal Wells presentation at the April 2013 peer review meeting held in Denver, Colorado.

  8. Development of an Improved Cement for Geothermal Wells

    SciTech Connect (OSTI)

    Trabits, George

    2015-04-20

    After an oil, gas, or geothermal production well has been drilled, the well must be stabilized with a casing (sections of steel pipe that are joined together) in order to prevent the walls of the well from collapsing. The gap between the casing and the walls of the well is filled with cement, which locks the casing into place. The casing and cementing of geothermal wells is complicated by the harsh conditions of high temperature, high pressure, and a chemical environment (brines with high concentrations of carbon dioxide and sulfuric acid) that degrades conventional Portland cement. During the 1990s and early 2000s, the U.S. Department of Energy’s Geothermal Technologies Office (GTO) provided support for the development of fly-ash-modified calcium aluminate phosphate (CaP) cement, which offers improved resistance to degradation compared with conventional cement. However, the use of CaP cements involves some operational constraints that can increase the cost and complexity of well cementing. In some cases, CaP cements are incompatible with chemical additives that are commonly used to adjust cement setting time. Care must also be taken to ensure that CaP cements do not become contaminated with leftover conventional cement in pumping equipment used in conventional well cementing. With assistance from GTO, Trabits Group, LLC has developed a zeolite-containing cement that performs well in harsh geothermal conditions (thermal stability at temperatures of up to 300°C and resistance to carbonation) and is easy to use (can be easily adjusted with additives and eliminates the need to “sterilize” pumping equipment as with CaP cements). This combination of properties reduces the complexity/cost of well cementing, which will help enable the widespread development of geothermal energy in the United States.

  9. Western tight gas sands advanced logging workshop proceedings

    SciTech Connect (OSTI)

    Jennings, J B; Carroll, Jr, H B

    1982-04-01

    An advanced logging research program is one major aspect of the Western Tight Sands Program. Purpose of this workshop is to help BETC define critical logging needs for tight gas sands and to allow free interchange of ideas on all aspects of the current logging research program. Sixteen papers and abstracts are included together with discussions. Separate abstracts have been prepared for the 12 papers. (DLC)

  10. Logging Calibration Models for Fission Neutron Sondes (September...

    Energy Savers [EERE]

    A Model for Water Factor Measurements With Fission-Neutron Logging Tools (May 1983) Field Calibration Facilities for Environmental Measurement of Radium, Thorium, and Potassium ...

  11. Pressure Temperature Log At Fish Lake Valley Area (DOE GTP) ...

    Open Energy Info (EERE)

    Fish Lake Valley Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Pressure Temperature Log At Fish Lake Valley Area (DOE GTP)...

  12. Image Logs At Coso Geothermal Area (2011) | Open Energy Information

    Open Energy Info (EERE)

    Date 2011 Usefulness useful DOE-funding Unknown Exploration Basis Determine crustul stress heterogeneity Notes Borehole induced structures in image logs of wells from the Coso...

  13. Method for determining formation quality factor from well log...

    Office of Scientific and Technical Information (OSTI)

    factor from well log data and its application to seismic reservoir characterization Citation Details In-Document Search Title: Method for determining formation quality factor ...

  14. Signatures in flowing fluid electric conductivity logs (Journal...

    Office of Scientific and Technical Information (OSTI)

    including analysis of natural regional flowin the permeable layer. A numerical model simulates flow and transport inthe wellbore during flowing FEC logging, and fracture ...

  15. Gamma-Ray Logging Workshop (February 1981) | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    for Models Used for Calibration of Gross-Count Gamma-Ray Logging Systems (December 1983) Parameter Assignments for Spectral Gamma-Ray Borehole Calibration Models (April 1984)

  16. Borehole Logging Methods for Exploration and Evaluation of Uranium...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    for Models Used for Calibration of Gross-Count Gamma-Ray Logging Systems (December 1983) Parameter Assignments for Spectral Gamma-Ray Borehole Calibration Models (April 1984

  17. Pressure Temperature Log At Colrado Area (DOE GTP) | Open Energy...

    Open Energy Info (EERE)

    Colrado Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Pressure Temperature Log At Colrado Area (DOE GTP) Exploration Activity...

  18. Pressure Temperature Log At Alum Area (DOE GTP) | Open Energy...

    Open Energy Info (EERE)

    Alum Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Pressure Temperature Log At Alum Area (DOE GTP) Exploration Activity Details...

  19. FMI Log At Maui Area (DOE GTP) | Open Energy Information

    Open Energy Info (EERE)

    Maui Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: FMI Log At Maui Area (DOE GTP) Exploration Activity Details Location Maui...

  20. Pressure Temperature Log At Mccoy Geothermal Area (DOE GTP) ...

    Open Energy Info (EERE)

    Mccoy Geothermal Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Pressure Temperature Log At Mccoy Geothermal Area (DOE GTP)...

  1. FMI Log At Wister Area (DOE GTP) | Open Energy Information

    Open Energy Info (EERE)

    Wister Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: FMI Log At Wister Area (DOE GTP) Exploration Activity Details Location...

  2. Pressure Temperature Log At Wister Area (DOE GTP) | Open Energy...

    Open Energy Info (EERE)

    Wister Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Pressure Temperature Log At Wister Area (DOE GTP) Exploration Activity...

  3. Pressure Temperature Log At Maui Area (DOE GTP) | Open Energy...

    Open Energy Info (EERE)

    Maui Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Pressure Temperature Log At Maui Area (DOE GTP) Exploration Activity Details...

  4. Acoustic Logs At Alum Area (Moos & Ronne, 2010) | Open Energy...

    Open Energy Info (EERE)

    tensile wall fractures, and were adequate to detect stratigraphic features. References Daniel Moos, Joel Ronne (2010) Selecting The Optimal Logging Suite For Geothermal Reservoir...

  5. Gamma Log At Coso Geothermal Area (1977) | Open Energy Information

    Open Energy Info (EERE)

    Coso Geothermal Area (1977) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Gamma Log At Coso Geothermal Area (1977) Exploration Activity Details...

  6. Acoustic Logs At Coso Geothermal Area (1977) | Open Energy Information

    Open Energy Info (EERE)

    1977) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Acoustic Logs At Coso Geothermal Area (1977) Exploration Activity Details Location Coso...

  7. Neutron Log At Coso Geothermal Area (1977) | Open Energy Information

    Open Energy Info (EERE)

    Coso Geothermal Area (1977) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Neutron Log At Coso Geothermal Area (1977) Exploration Activity...

  8. Pressure Temperature Log At Fort Bliss Area (DOE GTP) | Open...

    Open Energy Info (EERE)

    navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Pressure Temperature Log At Fort Bliss Area (DOE GTP) Exploration Activity Details Location Fort Bliss...

  9. Pressure Temperature Log At Silver Peak Area (DOE GTP) | Open...

    Open Energy Info (EERE)

    navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Pressure Temperature Log At Silver Peak Area (DOE GTP) Exploration Activity Details Location Silver Peak...

  10. Pressure Temperature Log At Flint Geothermal Area (DOE GTP) ...

    Open Energy Info (EERE)

    navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Pressure Temperature Log At Flint Geothermal Area (DOE GTP) Exploration Activity Details Location Flint...

  11. Pressure Temperature Log At Glass Buttes Area (DOE GTP) | Open...

    Open Energy Info (EERE)

    navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Pressure Temperature Log At Glass Buttes Area (DOE GTP) Exploration Activity Details Location Glass...

  12. Acoustic Logs At Coso Geothermal Area (2005) | Open Energy Information

    Open Energy Info (EERE)

    Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Acoustic Logs At Coso Geothermal Area (2005) Exploration Activity Details Location Coso...

  13. Well Log Data At North Brawley Geothermal Area (Matlick & Jayne...

    Open Energy Info (EERE)

    to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Well Log Data At North Brawley Geothermal Area (Matlick & Jayne, 2008) Exploration Activity Details...

  14. Well Log Data At North Brawley Geothermal Area (Edmunds & W....

    Open Energy Info (EERE)

    to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Well Log Data At North Brawley Geothermal Area (Edmunds & W., 1977) Exploration Activity Details...

  15. Well Log Data At Blue Mountain Geothermal Area (Fairbank & Niggemann...

    Open Energy Info (EERE)

    to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Well Log Data At Blue Mountain Geothermal Area (Fairbank & Niggemann, 2004) Exploration Activity...

  16. Well Log Techniques At Newberry Caldera Area (DOE GTP) | Open...

    Open Energy Info (EERE)

    navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Well Log Techniques At Newberry Caldera Area (DOE GTP) Exploration Activity Details Location Newberry...

  17. Well Log Techniques At Coso Geothermal Area (1985) | Open Energy...

    Open Energy Info (EERE)

    navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Well Log Techniques At Coso Geothermal Area (1985) Exploration Activity Details Location Coso Geothermal...

  18. Chemical Logging At Dixie Valley Geothermal Area (Los Alamos...

    Open Energy Info (EERE)

    Dixie Valley Geothermal Area (Los Alamos National Laboratory, NM, 2002) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Chemical Logging At Dixie...

  19. Chemical logging- a geothermal technique | Open Energy Information

    Open Energy Info (EERE)

    technique Abstract Chemical logging studies conducted at the Department of Energy's Raft River Geothermal Test Site in south central Idaho resulted in the development of a...

  20. Chemical Logging At Raft River Geothermal Area (1979) | Open...

    Open Energy Info (EERE)

    Raft River Geothermal Area (1979) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Chemical Logging At Raft River Geothermal Area (1979)...

  1. Acoustic Logs At Raft River Geothermal Area (1979) | Open Energy...

    Open Energy Info (EERE)

    Raft River Geothermal Area (1979) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Acoustic Logs At Raft River Geothermal Area (1979) Exploration...

  2. Energy Efficiency in Log Homes | Department of Energy

    Office of Environmental Management (EM)

    or purchasing a manufactured log home, you should consider several factors related to energy efficiency. The R-Value of Wood A material's thermal resistance or resistance to...

  3. Selecting The Optimal Logging Suite For Geothermal Reservoir...

    Open Energy Info (EERE)

    and tensile wall fractures, and were adequate to detect stratigraphic features. Density, photo-electric factor (PEF), neutron, and gamma ray (GR) logs provided sufficient...

  4. Density Log At Valles Caldera - Redondo Geothermal Area (Rowley...

    Open Energy Info (EERE)

    Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Density Log At Valles Caldera - Redondo Geothermal Area (Rowley, Et Al., 1987) Exploration...

  5. Density Log At Valles Caldera - Redondo Geothermal Area (Wilt...

    Open Energy Info (EERE)

    Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Density Log At Valles Caldera - Redondo Geothermal Area (Wilt & Haar, 1986) Exploration...

  6. Evaluation of Emerging Technology for Geothermal Drilling and Logging Applications

    Broader source: Energy.gov [DOE]

    Evaluation of Emerging Technology for Geothermal Drilling and Logging Applications presentation at the April 2013 peer review meeting held in Denver, Colorado.

  7. Drag reduction in coal log pipelines

    SciTech Connect (OSTI)

    Marrero, T.R.; Liu, H.

    1996-12-31

    It is well-known that solutions of dissolved long-chain macromolecules produce lower friction or drag losses than with the solvent alone. In coal log pipeline (CLP), water is the conveying medium. Synthetic polymers such as poly(ethylene oxide) have been dissolved in water and tested for their extent of drag reduction as a function of concentration and other variables. Lab-scale experimental results for CLP indicate substantial drag reduction at low concentration levels of polymer. But, the macromolecules exhibit degradation under mechanical shear stresses. The large molecules break into smaller units. This degradation effect causes a loss of drag reduction. However, high levels of drag reduction can be maintained as follows: (1) by injecting polymer into the CLP at several locations along the pipeline, (2) by injecting polymer of different particle sizes, (3) by using more robust types of polymers, or (4) by using polymer-fiber mixtures. This report presents the value of drag-reducing agents in terms of pumping power net cost savings. In addition, this report outlines the environmental impact of drag reduction polymers, and end-of-pipeline water treatment processes. For an operating CLP, hundreds of miles in length, the use of poly(ethylene oxide) as a drag reducing agent provides significant pumping power cost savings at a minimal materials cost.

  8. How gelation affects oil well cements

    SciTech Connect (OSTI)

    Kieffer, J.; Rae, P.

    1987-05-01

    One of the most common problems seen in the oil industry is that of cement gelation. Gelation can be defined as a premature viscosification or a gel-strength buildup of the cement slurry. This can have important consequences in field operations and may be so severe as to cause job failure. One of the principal difficulties encountered in dealing with cement gelation is the unpredictable nature of the phenomenon and the fact that it may manifest itself under a variety of field conditions. Thus, it may occur immediately after mixing or during the displacement when the slurry has reached circulating temperature; it occasionally is seen only during shutdowns, when the slurry is in static condition, but may appear during pumping when the slurry is under continual shear. The fact that the physico-chemical bases of gelation are complex probably accounts for the broad spectrum of conditions under which gelation can occur. Factors involved include the chemical composition of the cement powder itself, its fineness, its microstructure, the mixwater quality, the types (if any) of additive used, the rate of heat flux into the slurry as well as the final temperature to which the slurry is exposed.

  9. Qualified Energy Conservation Bonds

    Broader source: Energy.gov [DOE]

    Provides an in-depth description of qualified energy conservation bonds, including process and mechanics, case studies, utilization trends, barriers, and regulatory and legal issues. Author: Energy Programs Consortium

  10. Bonding aerogels with polyurethanes

    SciTech Connect (OSTI)

    Matthews, F.M.; Hoffman, D.M.

    1989-11-01

    Aerogels, porous silica glasses with ultra-fine cell size (30nm), are made by a solution gelation (sol-gel) process. The resulting gel is critical point dried to densities from 0.15--0.60 g/cc. This material is machinable, homogeneous, transparent, coatable and bondable. To bond aerogel an adhesive should have long cure time, no attack on the aerogel structure, and high strength. Several epoxies and urethanes were examined to determine if they satisfied these conditions. Bond strengths above 13 psi were found with double bubble and DP-110 epoxies and XI-208/ODA-1000 and Castall U-2630 urethanes. Hardman Kalex Tough Stuff'' A-85 hardness urethane gave 18 psi bond strength. Hardman A-85, Tuff-Stuff'' was selected for further evaluation because it produced bond strengths comparable to the adherend cohesive strength. 5 refs., 2 figs.

  11. Breaking the Bond

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Breaking the Bond 1663 Los Alamos science and technology magazine Latest Issue:July 2016 past issues All Issues » submit Breaking the Bond Can chemistry help unbind us from fossil fuels? July 21, 2016 info graphic gas pump Accelerating toward a more sustainable future: gas pumps may someday soon contain bio-gasoline made from plants. We are condensing millions of years of fossilization into a few chemical reactions. Fossil fuels are a finite resource. Unfortunately, the existing global

  12. Cementation and solidification of Rocky Flats Plant incinerator ash

    SciTech Connect (OSTI)

    Phillips, J.A.; Semones, G.B.

    1994-04-01

    Cementation studies on various aqueous waste streams at Rocky Flats have shown this technology to be effective for immobilizing the RCRA constituents in the waste. Cementation is also being evaluated for encapsulation of incinerator ash. Experiments will initially evaluate a surrogate ash waste using a Taguchi experimental design to optimize the cement formulation and waste loading levels for this application. Variables of waste loading, fly ash additions, water/cement ratio, and cement type will be tested at three levels each during the course of this work. Tests will finally be conducted on actual waste using the optimized cement formulation developed from this testing. This progression of tests will evaluate the effectiveness of cement encapsulation for this waste stream without generating any additional wastes.

  13. Low temperature material bonding technique

    DOE Patents [OSTI]

    Ramsey, J. Michael (Knoxville, TN); Foote, Robert S. (Oak Ridge, TN)

    2002-02-12

    A method of performing a lower temperature bonding technique to bond together two mating pieces of glass includes applying a sodium silicate aqueous solution between the two pieces.

  14. Low Temperature Material Bonding Technique

    DOE Patents [OSTI]

    Ramsey, J. Michael (Knoxville, TN); Foote, Robert S. (Oak Ridge, TN)

    2000-10-10

    A method of performing a lower temperature bonding technique to bond together two mating pieces of glass includes applying a sodium silicate aqueous solution between the two pieces.

  15. Intrinsic differences in atomic ordering of calcium (alumino)silicate hydrates in conventional and alkali-activated cements

    SciTech Connect (OSTI)

    White, Claire E.; Daemen, Luke L.; Hartl, Monika; Page, Katharine

    2015-01-15

    The atomic structures of calcium silicate hydrate (C–S–H) and calcium (–sodium) aluminosilicate hydrate (C–(N)–A–S–H) gels, and their presence in conventional and blended cement systems, have been the topic of significant debate over recent decades. Previous investigations have revealed that synthetic C–S–H gel is nanocrystalline and due to the chemical similarities between ordinary Portland cement (OPC)-based systems and low-CO{sub 2} alkali-activated slags, researchers have inferred that the atomic ordering in alkali-activated slag is the same as in OPC–slag cements. Here, X-ray total scattering is used to determine the local bonding environment and nanostructure of C(–A)–S–H gels present in hydrated tricalcium silicate (C{sub 3}S), blended C{sub 3}S–slag and alkali-activated slag, revealing the large intrinsic differences in the extent of nanoscale ordering between C–S–H derived from C{sub 3}S and alkali-activated slag systems, which may have a significant influence on thermodynamic stability, and material properties at higher length scales, including long term durability of alkali-activated cements.

  16. Effect of different water levels on the properties of HSR Class G cement

    SciTech Connect (OSTI)

    Bensted, J. . Sunbury Research Centre)

    1994-01-01

    HSR (high sulfate-resistant) Class G cement is the most widely utilized oilwell cement in the Eastern Hemisphere. Changes in water level corresponding to small changes in slurry density have a substantial effect upon the physical cementing properties of HSR Class G oilwell cement under comparable conditions. The implications of this for practical oilwell cement slurry formulations for downhole usage are discussed.

  17. Cement Kiln Flue Gas Recovery Scrubber Project

    SciTech Connect (OSTI)

    National Energy Technology Laboratory

    2001-11-30

    The Cement Kiln Flue Gas Recovery Scrubber Project was a technical success and demonstrated the following: CKD can be used successfully as the sole reagent for removing SO2 from cement kiln flue gas, with removal efficiencies of 90 percent or greater; Removal efficiencies for HCl and VOCs were approximately 98 percent and 70 percent, respectively; Particulate emissions were low, in the range of 0.005 to 0.007 grains/standard cubic foot; The treated CKD sorbent can be recycled to the kiln after its potassium content has been reduced in the scrubber, thereby avoiding the need for landfilling; The process can yield fertilizer-grade K2SO4, a saleable by-product; and Waste heat in the flue gas can provide the energy required for evaporation and crystallization in the by-product recovery operation. The demonstration program established the feasibility of using the Recovery Scrubber{trademark} for desulfurization of flue gas from cement kilns, with generally favorable economics, assuming tipping fees are available for disposal of ash from biomass combustion. The process appears to be suitable for commercial use on any type of cement kiln. EPA has ruled that CKD is a nonhazardous waste, provided the facility meets Performance Standards for the Management of CKD (U.S. Environmental Protection Agency 1999d). Therefore, regulatory drivers for the technology focus more on reduction of air pollutants and pollution prevention, rather than on treating CKD as a hazardous waste. Application of the Recovery Scrubbe{trademark} concept to other waste-disposal operations, where pollution and waste reductions are needed, appears promising.

  18. Effective Permeability Change in Wellbore Cement with Carbon Dioxide Reaction

    SciTech Connect (OSTI)

    Um, Wooyong; Jung, Hun Bok; Martin, Paul F.; McGrail, B. Peter

    2011-11-01

    Portland cement, a common sealing material for wellbores for geological carbon sequestration was reacted with CO{sub 2} in supercritical, gaseous, and aqueous phases at various pressure and temperature conditions to simulate cement-CO{sub 2} reaction along the wellbore from carbon injection depth to the near-surface. Hydrated Portland cement columns (14 mm diameter x 90 mm length; water-to-cement ratio = 0.33) including additives such as steel coupons and Wallula basalt fragments were reacted with CO{sub 2} in the wet supercritical (the top half) and dissolved (the bottom half) phases under carbon sequestration condition with high pressure (10 MPa) and temperature (50 C) for 5 months, while small-sized hydrated Portland cement columns (7 mm diameter x 20 mm length; water-to-cement ratio = 0.38) were reacted with CO{sub 2} in dissolved phase at high pressure (10 MPa) and temperature (50 C) for 1 month or with wet CO{sub 2} in gaseous phase at low pressure (0.2 MPa) and temperature (20 C) for 3 months. XMT images reveal that the cement reacted with CO{sub 2} saturated groundwater had degradation depth of {approx}1 mm for 1 month and {approx}3.5 mm for 5 month, whereas the degradation was minor with cement exposure to supercritical CO{sub 2}. SEM-EDS analysis showed that the carbonated cement was comprised of three distinct zones; the innermost less degraded zone with Ca atom % > C atom %, the inner degraded zone with Ca atom % {approx} C atom % due to precipitation of calcite, the outer degraded zone with C atom % > Ca atom % due to dissolution of calcite and C-S-H, as well as adsorption of carbon to cement matrix. The outer degraded zone of carbonated cement was porous and fractured because of dissolution-dominated reaction by carbonic acid exposure, which resulted in the increase in BJH pore volume and BET surface area. In contrast, cement-wet CO{sub 2}(g) reaction at low P (0.2 MPa)-T (20 C) conditions for 1 to 3 months was dominated by precipitation of micron

  19. Geothermal well log interpretation state of the art. Final report

    SciTech Connect (OSTI)

    Sanyal, S.K.; Wells, L.E.; Bickham, R.E.

    1980-01-01

    An in-depth study of the state of the art in Geothermal Well Log Interpretation has been made encompassing case histories, technical papers, computerized literature searches, and actual processing of geothermal wells from New Mexico, Idaho, and California. A classification scheme of geothermal reservoir types was defined which distinguishes fluid phase and temperature, lithology, geologic province, pore geometry, salinity, and fluid chemistry. Major deficiencies of Geothermal Well Log Interpretation are defined and discussed with recommendations of possible solutions or research for solutions. The Geothermal Well Log Interpretation study and report has concentrated primarily on Western US reservoirs. Geopressured geothermal reservoirs are not considered.

  20. Proceedings of the second PFN uranium logging seminar

    SciTech Connect (OSTI)

    Not Available

    1983-01-01

    The Prompt Fission Neutron (PFN) uranium logging system developed by Sandia National Laboratories for the US Department of Energy is described in some detail in papers by the staff that was involved in the final phase of the development project, and by others associated with the project as users of the logging probe or builders of some of the probe hardware. Descriptions are provided of the probe's electronic circuits, the uphole instrumentation, the log interpretation technique, field experience, neutron detection hardware, neutron generator design, life-test results, and observations by Bendix Field Engineering Corporation personnel regarding the use of the probe and its results.

  1. Diffusion Bonding Characterization

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Diffusion Bonding Characterization - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Energy Defense Waste Management Programs

  2. Photochemical tissue bonding

    DOE Patents [OSTI]

    Redmond, Robert W.; Kochevar, Irene E.

    2012-01-10

    Photochemical tissue bonding methods include the application of a photosensitizer to a tissue and/or tissue graft, followed by irradiation with electromagnetic energy to produce a tissue seal. The methods are useful for tissue adhesion, such as in wound closure, tissue grafting, skin grafting, musculoskeletal tissue repair, ligament or tendon repair and corneal repair.

  3. GRAPHITE BONDING METHOD

    DOE Patents [OSTI]

    King, L.D.P.

    1964-02-25

    A process for bonding or joining graphite members together in which a thin platinum foil is placed between the members, heated in an inert atmosphere to a temperature of 1800 deg C, and then cooled to room temperature is described. (AEC)

  4. Lehigh Southwest Cement Company: Compressed Air System Improvement Saves Energy at a Lehigh Southwest Cement Plant

    SciTech Connect (OSTI)

    Not Available

    2003-10-01

    In 2001, Lehigh Southwest Cement Company improved the compressed air system at its cement plant in Tehachapi, California. Consequently, the system was able to operate more efficiently with less compressor capacity and at a lower system pressure. The project yielded total annual savings of 895,000 kWh and $199,000. The initial project cost was $417,000, but Southern California Edison provided a $90,000 incentive payment to reduce the cost to $327,000. Simple payback was about 20 months.

  5. Imaging Wellbore Cement Degradation by Carbon Dioxide under Geologic...

    Office of Scientific and Technical Information (OSTI)

    Journal Article: Imaging Wellbore Cement Degradation by Carbon Dioxide under Geologic Sequestration Conditions Using X-ray Computed Microtomography Citation Details In-Document ...

  6. Stabilizing coal-water mixtures with portland cement

    DOE Patents [OSTI]

    Steinberg, Meyer; Krishna, Coimbatore R.

    1986-01-01

    Coal-water mixes stabilized by the addition of portland cement which may additionally contain retarding carbohydrates, or borax are described.

  7. Dynamic Evolution of Cement Composition and Transport Properties...

    Office of Scientific and Technical Information (OSTI)

    Carbon Sequestration Citation Details In-Document Search Title: Dynamic Evolution of Cement Composition and Transport Properties under Conditions Relevant to Geological Carbon ...

  8. Corrosion-resistant Foamed Cements for Carbon Steels

    SciTech Connect (OSTI)

    Sugama T.; Gill, S.; Pyatina, T., Muraca, A.; Keese, R.; Khan, A.; Bour, D.

    2012-12-01

    The cementitious material consisting of Secar #80, Class F fly ash, and sodium silicate designed as an alternative thermal-shock resistant cement for the Enhanced Geothermal System (EGS) wells was treated with cocamidopropyl dimethylamine oxide-based compound as foaming agent (FA) to prepare numerous air bubble-dispersed low density cement slurries of and #61603;1.3 g/cm3. Then, the foamed slurry was modified with acrylic emulsion (AE) as corrosion inhibitor. We detailed the positive effects of the acrylic polymer (AP) in this emulsion on the five different properties of the foamed cement: 1) The hydrothermal stability of the AP in 200 and #61616;C-autoclaved cements; 2) the hydrolysis-hydration reactions of the slurry at 85 and #61616;C; 3) the composition of crystalline phases assembled and the microstructure developed in autoclaved cements; 4) the mechanical behaviors of the autoclaved cements; and, 5) the corrosion mitigation of carbon steel (CS) by the polymer. For the first property, the hydrothermal-catalyzed acid-base interactions between the AP and cement resulted in Ca-or Na-complexed carboxylate derivatives, which led to the improvement of thermal stability of the AP. This interaction also stimulated the cement hydration reactions, enhancing the total heat evolved during cement’s curing. Addition of AP did not alter any of the crystalline phase compositions responsible for the strength of the cement. Furthermore, the AP-modified cement developed the porous microstructure with numerous defect-free cavities of disconnected voids. These effects together contributed to the improvement of compressive-strength and –toughness of the cured cement. AP modification of the cement also offered an improved protection of CS against brine-caused corrosion. There were three major factors governing the corrosion protection: 1) Reducing the extents of infiltration and transportation of corrosive electrolytes through the cement layer deposited on the underlying CS

  9. Stabilizing coal-water mixtures with Portland cement

    DOE Patents [OSTI]

    Steinberg, M.; Krishna, C.R.

    1984-10-17

    Coal-water mixes stabilized by the addition of Portland cement which may additionally contain retarding carbohydrates, or borax are described. 1 tab.

  10. Investigation of Possible Wellbore Cement Failures During Hydraulic...

    Office of Scientific and Technical Information (OSTI)

    Journal Article: Investigation of Possible Wellbore Cement Failures During Hydraulic Fracturing Operations Citation Details In-Document Search Title: Investigation of Possible ...

  11. Change in pore structure and composition of hardened cement paste...

    Office of Scientific and Technical Information (OSTI)

    To investigate the alteration associated with dissolution, dissolution tests of ordinary Portland cement (OPC) hydrates were performed. Through observation of the samples after ...

  12. Image Logs At Coso Geothermal Area (2004) | Open Energy Information

    Open Energy Info (EERE)

    Coso Geothermal Region Notes During the second year of this project, wellbore logs and stress data were acquired in a new production well drilled in the Coso Geothermal Field,...

  13. Long Valley Caldera Field Trip Log | Open Energy Information

    Open Energy Info (EERE)

    to library Conference Paper: Long Valley Caldera Field Trip Log Abstract NA Authors Gene A. Suemnicht and Bastien Poux Conference NGA Long Valley Field Trip, July 5-7, 2012;...

  14. Efficiently log and perforate 60 + wells with coiled tubing

    SciTech Connect (OSTI)

    Fertl, W.H.; Hotz, R.F.

    1987-07-01

    In today's petroleum industry, more and more emphasis is being placed on logging and completion techniques for highly deviated (extended-reach) and horizontal boreholes. This is the result of cost-effective development of oil and gas via: a minimum number of production platforms on large structures, incremental but marginal reserves in outlying and/or small fault blocks, shallow reservoirs in deep offshore waters, and significant hydrocarbon accumulations in environmentally sensitive and/or restrictive areas, e.g., perma-frost, urban areas, etc. The major challenge in logging such high-angle, extended-reach, and also horizontal boreholes is guiding the logging tool string to the bottom of the wellbore. In the horizontal portion of a borehole, the use of coiled tubing has proven successful in ''pushing'' the logging instrumentation toward the bottom (end) of the borehole.

  15. JOBAID-LOGGING IN TO THE OLC LEARNING SYSTEM

    Office of Energy Efficiency and Renewable Energy (EERE)

    In this job aid you will Log In to the system, Retrieve Forgotten Password and/or User ID, and Use the LMS Help System built into the application.

  16. NMOCD - Form G-105 - Geothermal Resources Well Log | Open Energy...

    Open Energy Info (EERE)

    Jump to: navigation, search OpenEI Reference LibraryAdd to library General: NMOCD - Form G-105 - Geothermal Resources Well Log Author State of New Mexico Energy and Minerals...

  17. Fluid-Rock Characterization and Interactions in NMR Well Logging

    SciTech Connect (OSTI)

    Hirasaki, George J.; Mohanty, Kishore K.

    2003-02-10

    The objective of this project was to characterize the fluid properties and fluid-rock interactions that are needed for formation evaluation by NMR well logging. The advances made in the understanding of NMR fluid properties are summarized in a chapter written for an AAPG book on NMR well logging. This includes live oils, viscous oils, natural gas mixtures, and the relation between relaxation time and diffusivity.

  18. Fluid-Rock Characterization and Interactions in NMR Well Logging

    SciTech Connect (OSTI)

    Hirasaki, George J.; Mohanty, Kishore K.

    2003-02-10

    The objective of this project was to characterize the fluid properties and fluid-rock interactions which are needed for formation evaluation by NMR well logging. NMR well logging is finding wide use in formation evaluation. The formation parameters commonly estimated were porosity, permeability, and capillary bound water. Special cases include estimation of oil viscosity, residual oil saturation, location of oil/water contact, and interpretation on whether the hydrocarbon is oil or gas.

  19. Composition and application of novel sprayable phosphate cement (grancrete) that bonds to styrofoam

    DOE Patents [OSTI]

    Wagh, Arun S.; Paul, Jr., James W.

    2007-01-09

    A dry mix particulate composition of a calcined oxide of Mg and/or Ca, an acid phosphate, and fly ash or equivalent, wherein the calcined oxide is present in the range of from about 17% to about 40% by weight and the acid phosphate is present in the range of from about 29% to about 52% by weight and the fly ash or equivalent is present in the range of from about 24% to about 39% by weight when sand is added to the dry mix, it is present in the range of from about 39% to about 61% by weight of the combined dry mix and sand. A method of forming a structural member is also disclosed wherein an aqueous slurry of about 8 12 pounds of water is added to dry mix and sand.

  20. Microsoft Word - NETL-TRS-X-2015_Field-Generated Foamed Cement...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... The initial field-generated foamed cement testing revealed the structure of the ... The heterogeneous structure suggests the motion of the foamed cement slurry within the vessels ...

  1. Bond Program | Open Energy Information

    Open Energy Info (EERE)

    Bond Program Jump to: navigation, search This article is a stub. You can help OpenEI by expanding it. Retrieved from "http:en.openei.orgwindex.php?titleBondProgram&oldid5427...

  2. Opportunities in Bond Financing

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Opportunities in Bond Financing James Dack Vice President Alternative Energy Finance Group Stern Brothers & Co. Seattle, WA 98101 Biogas and Fuel Cells Workshop National Renewable Energy Laboratory Golden, Colorado June 11-13, 2012 2 INTRODUCTION * Stern Brothers, founded in 1917 and headquartered in St. Louis, is an investment banking firm that is focused on project financing (taxable and tax-exempt) for renewable energy, real estate, higher education and healthcare. * Stern's Alternative

  3. Low temperature reactive bonding

    DOE Patents [OSTI]

    Makowiecki, Daniel M. (Livermore, CA); Bionta, Richard M. (Livermore, CA)

    1995-01-01

    The joining technique requires no external heat source and generates very little heat during joining. It involves the reaction of thin multilayered films deposited on faying surfaces to create a stable compound that functions as an intermediate or braze material in order to create a high strength bond. While high temperatures are reached in the reaction of the multilayer film, very little heat is generated because the films are very thin. It is essentially a room temperature joining process.

  4. Guidebook for Using the Tool BEST Cement: Benchmarking and Energy Savings Tool for the Cement Industry

    SciTech Connect (OSTI)

    Galitsky, Christina; Price, Lynn; Zhou, Nan; Fuqiu , Zhou; Huawen, Xiong; Xuemin, Zeng; Lan, Wang

    2008-07-30

    The Benchmarking and Energy Savings Tool (BEST) Cement is a process-based tool based on commercially available efficiency technologies used anywhere in the world applicable to the cement industry. This version has been designed for use in China. No actual cement facility with every single efficiency measure included in the benchmark will likely exist; however, the benchmark sets a reasonable standard by which to compare for plants striving to be the best. The energy consumption of the benchmark facility differs due to differences in processing at a given cement facility. The tool accounts for most of these variables and allows the user to adapt the model to operational variables specific for his/her cement facility. Figure 1 shows the boundaries included in a plant modeled by BEST Cement. In order to model the benchmark, i.e., the most energy efficient cement facility, so that it represents a facility similar to the user's cement facility, the user is first required to input production variables in the input sheet (see Section 6 for more information on how to input variables). These variables allow the tool to estimate a benchmark facility that is similar to the user's cement plant, giving a better picture of the potential for that particular facility, rather than benchmarking against a generic one. The input variables required include the following: (1) the amount of raw materials used in tonnes per year (limestone, gypsum, clay minerals, iron ore, blast furnace slag, fly ash, slag from other industries, natural pozzolans, limestone powder (used post-clinker stage), municipal wastes and others); the amount of raw materials that are preblended (prehomogenized and proportioned) and crushed (in tonnes per year); (2) the amount of additives that are dried and ground (in tonnes per year); (3) the production of clinker (in tonnes per year) from each kiln by kiln type; (4) the amount of raw materials, coal and clinker that is ground by mill type (in tonnes per year); (5

  5. IMPROVED BONDING METHOD

    DOE Patents [OSTI]

    Padgett, E.V. Jr.; Warf, D.H.

    1964-04-28

    An improved process of bonding aluminum to aluminum without fusion by ultrasonic vibrations plus pressure is described. The surfaces to be bonded are coated with an aqueous solution of alkali metal stearate prior to assembling for bonding. (AEC) O H19504 Present information is reviewed on steady state proliferation, differentiation, and maturation of blood cells in mammals. Data are cited from metabolic tracer studies, autoradiographic studies, cytologic studies, studies of hematopoietic response to radiation injuries, and computer analyses of blood cell production. A 3-step model for erythropoiesis and a model for granulocyte kinetics are presented. New approaches to the study of lymphocytopoiesis described include extracorporeal blood irradiation to deplete lymphocytic tissue without direct injury to the formative tissues as a means to study the stressed system, function control, and rates of proliferation. It is pointed out that present knowledge indicates that lymphocytes comprise a mixed family, with diverse life spans, functions, and migration patterns with apparent aimless recycling from modes to lymph to blood to nodes that has not yet been quantitated. Areas of future research are postulated. (70 references.) (C.H.)

  6. Bonding Tools | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Bonding Tools Bonding Tools Bonds are one of the most common forms of financing used by state and local governments, because they are a low-cost source of capital available to most entities. State and local officials may consider using bonds for a variety of clean energy purposes, including: Financing a specific set of energy upgrades in their own facilities (can be combined with an energy savings performance contract) Capitalizing finance programs (e.g., revolving loan fund) for public sector

  7. Qualified Energy Conservation Bond Webinars

    Broader source: Energy.gov [DOE]

    Provides a listing of past qualified energy conservation bond webinars and associated files. Author: U.S. Department of Energy

  8. Magnesium phosphate glass cements with ceramic-type properties

    DOE Patents [OSTI]

    Sugama, Toshifumi; Kukacka, Lawrence E.

    1984-03-13

    Rapid setting magnesium phosphate (Mg glass) cementitious materials consisting of magnesium phosphate cement paste, polyborax and water-saturated aggregate exhibiting rapid setting and high early strength characteristics. The magnesium glass cement is prepared from a cation-leachable powder and a bivalent metallic ion-accepting liquid such as an aqueous solution of diammonium phosphate and ammonium polyphosphate. The cation-leachable powder includes a mixture of two different magnesium oxide powders processed and sized differently which when mixed with the bivalent metallic ion-accepting liquid provides the magnesium glass cement consisting primarily of magnesium ortho phosphate tetrahydrate, with magnesium hydroxide and magnesium ammonium phosphate hexahydrate also present. The polyborax serves as a set-retarder. The resulting magnesium mono- and polyphosphate cements are particularly suitable for use as a cementing matrix in rapid repair systems for deteriorated concrete structures as well as construction materials and surface coatings for fireproof structures.

  9. Magnesium-phosphate-glass cements with ceramic-type properties

    DOE Patents [OSTI]

    Sugama, T.; Kukacka, L.E.

    1982-09-23

    Rapid setting magnesium phosphate (Mg glass) cementitious materials consisting of magnesium phosphate cement paste, polyborax and water-saturated aggregate, exhibits rapid setting and high early strength characteristics. The magnesium glass cement is prepared from a cation-leachable powder and a bivalent metallic ion-accepting liquid such as an aqueous solution of diammonium phosphate and ammonium polyphosphate. The cation-leachable powder includes a mixture of two different magnesium oxide powders processed and sized differently which when mixed with the bivalent metallic ion-accepting liquid provides the magnesium glass cement consisting primarily of magnesium ortho phosphate tetrahydrate, with magnesium hydroxide and magnesium ammonium phosphate hexahydrate also present. The polyborax serves as a set-retarder. The resulting magnesium mono- and polyphosphate cements are particularly suitable for use as a cementing matrix in rapid repair systems for deteriorated concrete structures as well as construction materials and surface coatings for fireproof structures.

  10. Use of hazardous waste in cement kilns backed

    SciTech Connect (OSTI)

    Krieger, J.

    1993-07-19

    Cement kiln operators who are making use of hazardous waste as a partial substitute for fossil fuel now have a better engineering foundation for determining what is going on in the kilns and how to optimize their operations. A just-released study by a scientific advisory board of experts commissioned by the Cement Kiln Recycling Coalition (CKRC) in Washington, DC, has provided an in-depth look, at such operations and finds the practice to be a fundamentally sound' technology. Long residence times and high temperatures in cement kilns maximize the combustion efficiency for waste-derived fuels, according to the study report. The scientific advisory board notes that all organic compounds can be destroyed in a kiln at 99.9999% efficiency. Also, the behavior of metals in cement kilns can be readily measured, predicted, and controlled. Cement kilns are extremely efficient in reducing metals emissions.

  11. Data Compendium for the Logging Test Pits at the ERDA Grand Junction...

    Office of Environmental Management (EM)

    Data Compendium for the Logging Test Pits at the ERDA Grand Junction Compound (December 1975) Data Compendium for the Logging Test Pits at the ERDA Grand Junction Compound ...

  12. Neutron Log At Alum Area (Moos & Ronne, 2010) | Open Energy Informatio...

    Open Energy Info (EERE)

    Technique Neutron Log Activity Date Usefulness useful DOE-funding Unknown Notes Density, photo-electric factor (PEF), neutron, and gamma ray (GR) logs provided sufficient...

  13. Gamma Log At Alum Area (Moos & Ronne, 2010) | Open Energy Information

    Open Energy Info (EERE)

    Technique Gamma Log Activity Date Usefulness useful DOE-funding Unknown Notes Density, photo-electric factor (PEF), neutron, and gamma ray (GR) logs provided sufficient...

  14. Technical evaluation of software for gamma-ray logging system

    SciTech Connect (OSTI)

    Stromswold, D.C.

    1994-05-01

    This report contains results of a technical review of software, identified as LGCALC, that processes data collected by a high-resolution gamma-ray borehole logging system. The software presently operates within Westinghouse Hanford Company, Department of Geosciences, to process data collected by the Radionuclide Logging System. The software has been reviewed for its suitability for processing data to be collected by new high-resolution gamma-ray logging trucks scheduled to begin operational tests within Westinghouse Tank Waste Remediation Systems during 1994. Examination of the program code and hands-on operational tests have shown that this software is suitable for its intended use of processing high-resolution gamma-ray data obtained from borehole logging. Most of the code requires no changes, but in a few limited cases, suggestions have been made to correct errors or improve operation. Section 4 describes these changes. The technical review has confirmed the appropriateness, correctness, completeness, and coding accuracy of algorithms used to process spectral gamma-ray data, leading to a calculation of subsurface radionuclide contaminants. Running the program with test data from calibration models has confirmed that the program operates correctly. Comparisons with hand calculations have shown the correctness of the output from the program, based on known input data. Section 3 describes these tests. The recommended action is to make the near term programming changes suggested in Section 4.1 and then use the LGCALC analysis program with the new high-resolution logging systems once they have been properly calibrated.

  15. Logging with coiled tubing less effective than with drill pipe

    SciTech Connect (OSTI)

    Van Den Bosch, R. )

    1994-01-31

    Coiled tubing offered neither economic nor operational advantages over drill pipe for conveying logging tools in open hole shallow horizontal wells in Germany. In the past 2 years, Mobil Erdgas-Erdoel GMbH (MEEG) participated in completing eight shallow horizontal wells. These were medium-to-short radius wells at measured depths of between 850 and 2,000 m. The average horizontal section was 350 m. The logging tools were conveyed by coiled tubing or drill pipe. MEEG attempted to log five wells with coiled tubing-conveyed tools, four with 1 1/2-in. tubing. Total depth was reached reliably in only one well, the shallowest and with the shortest horizontal section. Simulation programs were unreliable for calculating the downhole forces of the coil/tool combination or predicting possible helical lockups. In wells with drill pipe-conveyed logs, the tool combination could always be pushed to total depth, and the operations were generally faster and cost less than logging with coiled tubing. Also, drill pipe allowed longer and heavier tool strings. For reliable operations, coiled tubing needs to be more rigid, rig-up/rig-down times need to be improved, and the simulation programs must be more reliable for predicting downhole lock-up.

  16. Global warming impact on the cement and aggregates industries

    SciTech Connect (OSTI)

    Davidovits, J. . Geopolymer Inst.)

    1994-06-01

    CO[sub 2] related energy taxes are focusing essentially on fuel consumption, not on actual CO[sub 2] emission measured at the chimneys. Ordinary Portland cement, used in the aggregates and industries, results from the calcination of limestone and silica. The production of 1 ton of cement directly generates 0.55 tons of chemical-CO[sub 2] and requires the combustion of carbon-fuel to yield an additional 0.40 tons of CO[sub 2]. The 1987 1 billion metric tons world production of cement accounted for 1 billion metric tons of CO[sub 2], i.e., 5% of the 1987 world CO[sub 2] emission. A world-wide freeze of CO[sub 2] emission at the 1990 level as recommended by international institutions, is incompatible with the extremely high cement development needs of less industrialized countries. Present cement production growth ranges from 5% to 16% and suggests that in 25 years from now, world cement CO[sub 2] emissions could equal 3,500 million tons. Eco-taxes when applied would have a spectacular impact on traditional Portland cement based aggregates industries. Taxation based only on fuel consumption would lead to a cement price increase of 20%, whereas taxation based on actual CO[sub 2] emission would multiply cement price by 1.5 to 2. A 25--30% minor reduction of CO[sub 2] emissions may be achieved through the blending of Portland cement with replacement materials such as coal-fly ash and iron blast furnace slag.

  17. Odor investigation of a Portland cement plant

    SciTech Connect (OSTI)

    Pleus, R.C. [Intertox, Inc., Seattle, WA (United States)

    1998-12-31

    The main concern expressed by Smithville residents is whether the odors they were smelling during odor events were due to chemicals that could cause adverse health effects. Odors were allegedly emanating from the town`s Portland cement plant. The purpose of the study was to measure the ambient air for 20 reduced sulfur, 50 volatile organic compounds, and air samples for olfactometric analysis. Carbonyl sulfide was found to be at a concentration that could create a sense of odor and irritation. This sense of irritation may be due to a physiological response by the central nervous system, and is not associated with any known adverse effects. This physiological response could account for some or all of the irritation experienced by residents during odor events. Comparing chemical concentrations that were detected in air samples to standard and recognized guidelines for acceptable exposure, all measured concentrations were found to be well below the acceptable criteria. From these data the authors conclude that no acute or chronic adverse health effects are expected at the concentrations of the chemicals detected downwind of the cement plant, either routinely or during odor events.

  18. Incinerators and cement kilns face off

    SciTech Connect (OSTI)

    Kim, I.

    1994-04-01

    For the past few years, US incinerators have been at odds with thermal waste processors such as cement kilns. Originally, there was enough room in the industrial waste treatment market for both types of treatment. As waste generators turned to pollution prevention and onsite treatment, however, the volume of waste decreased and its composition changed. Now, each sees the other crowding it out of a tightening market, and the fight between them is growing increasingly bitter. At the center of this battle are the products of alternative thermal processes--for cement kilns, the dust formed after processing, and for other processes, a variety of materials, many of which can be used for construction. Currently, these materials are exempted from regulation under the US Resource Conservation and Recovery Act (RCRA). In addition, the alternative processes offer generators a significant cost advantage over incineration. The question that US regulators are now grappling with is whether these materials are safe enough to justify this preferential treatment. So far, the answer seems to be a qualified yes. The paper discusses these issues.

  19. Low temperature reactive bonding

    DOE Patents [OSTI]

    Makowiecki, D.M.; Bionta, R.M.

    1995-01-17

    The joining technique is disclosed that requires no external heat source and generates very little heat during joining. It involves the reaction of thin multilayered films deposited on faying surfaces to create a stable compound that functions as an intermediate or braze material in order to create a high strength bond. While high temperatures are reached in the reaction of the multilayer film, very little heat is generated because the films are very thin. It is essentially a room temperature joining process. 5 figures.

  20. Solder extrusion pressure bonding process and bonded products produced thereby

    DOE Patents [OSTI]

    Beavis, Leonard C.; Karnowsky, Maurice M.; Yost, Frederick G.

    1992-01-01

    Production of soldered joints which are highly reliable and capable of surviving 10,000 thermal cycles between about -40.degree. C. and 110.degree. C. Process involves interposing a thin layer of a metal solder composition between the metal surfaces of members to be bonded and applying heat and up to about 1000 psi compression pressure to the superposed members, in the presence of a reducing atmosphere, to extrude the major amount of the solder composition, contaminants including fluxing gases and air, from between the members being bonded, to form a very thin, strong intermetallic bonding layer having a thermal expansion tolerant with that of the bonded members.

  1. Solder extrusion pressure bonding process and bonded products produced thereby

    DOE Patents [OSTI]

    Beavis, L.C.; Karnowsky, M.M.; Yost, F.G.

    1992-06-16

    Disclosed is a process for production of soldered joints which are highly reliable and capable of surviving 10,000 thermal cycles between about [minus]40 C and 110 C. Process involves interposing a thin layer of a metal solder composition between the metal surfaces of members to be bonded and applying heat and up to about 1000 psi compression pressure to the superposed members, in the presence of a reducing atmosphere, to extrude the major amount of the solder composition, contaminants including fluxing gases and air, from between the members being bonded, to form a very thin, strong intermetallic bonding layer having a thermal expansion tolerant with that of the bonded members.

  2. Energy Efficiency Improvement Opportunities for the Cement Industry

    SciTech Connect (OSTI)

    Price, Lynn; Worrell, Ernst; Galitsky, Christina; Price, Lynn

    2008-01-31

    This report provides information on the energy savings, costs, and carbon dioxide emissions reductions associated with implementation of a number of technologies and measures applicable to the cement industry. The technologies and measures include both state-of-the-art measures that are currently in use in cement enterprises worldwide as well as advanced measures that are either only in limited use or are near commercialization. This report focuses mainly on retrofit measures using commercially available technologies, but many of these technologies are applicable for new plants as well. Where possible, for each technology or measure, costs and energy savings per tonne of cement produced are estimated and then carbon dioxide emissions reductions are calculated based on the fuels used at the process step to which the technology or measure is applied. The analysis of cement kiln energy-efficiency opportunities is divided into technologies and measures that are applicable to the different stages of production and various kiln types used in China: raw materials (and fuel) preparation; clinker making (applicable to all kilns, rotary kilns only, vertical shaft kilns only); and finish grinding; as well as plant wide measures and product and feedstock changes that will reduce energy consumption for clinker making. Table 1 lists all measures in this report by process to which they apply, including plant wide measures and product or feedstock changes. Tables 2 through 8 provide the following information for each technology: fuel and electricity savings per tonne of cement; annual operating and capital costs per tonne of cement or estimated payback period; and, carbon dioxide emissions reductions for each measure applied to the production of cement. This information was originally collected for a report on the U.S. cement industry (Worrell and Galitsky, 2004) and a report on opportunities for China's cement kilns (Price and Galitsky, in press). The information provided in this

  3. Fluid-Rock Characterization and Interactions in NMR Well Logging

    SciTech Connect (OSTI)

    George J. Hirasaki; Kishore K. Mohanty

    2005-09-05

    The objective of this report is to characterize the fluid properties and fluid-rock interactions that are needed for formation evaluation by NMR well logging. The advances made in the understanding of NMR fluid properties are summarized in a chapter written for an AAPG book on NMR well logging. This includes live oils, viscous oils, natural gas mixtures, and the relation between relaxation time and diffusivity. Oil based drilling fluids can have an adverse effect on NMR well logging if it alters the wettability of the formation. The effect of various surfactants on wettability and surface relaxivity are evaluated for silica sand. The relation between the relaxation time and diffusivity distinguishes the response of brine, oil, and gas in a NMR well log. A new NMR pulse sequence in the presence of a field gradient and a new inversion technique enables the T{sub 2} and diffusivity distributions to be displayed as a two-dimensional map. The objectives of pore morphology and rock characterization are to identify vug connectivity by using X-ray CT scan, and to improve NMR permeability correlation. Improved estimation of permeability from NMR response is possible by using estimated tortuosity as a parameter to interpolate between two existing permeability models.

  4. Dual-cone double-helical downhole logging device

    DOE Patents [OSTI]

    Yu, Jiunn S.

    1984-01-01

    A broadband downhole logging device includes a double-helix coil wrapped over a dielectric support and surrounded by a dielectric shield. The device may also include a second coil longitudinally aligned with a first coil and enclosed within the same shield for measuring magnetic permeability of downhole formations and six additional coils for accurately determining downhole parameters.

  5. Strength recovery of cement composites in steam and carbonate environments

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Tom Butcher

    2016-04-28

    The data include compressive strength and Young's Modulus recoveries in steam and carbonate environments at 270degC for four chemically different cement composites after imposed controlled damaged.

  6. Mechanical and acoustic properties of weakly cemented granular rocks

    SciTech Connect (OSTI)

    Nakagawa, S.; Myer, L.R.

    2001-05-09

    This paper presents the results of laboratory measurements on the mechanical and acoustic properties of weakly cemented granular rock. Artificial rock samples were fabricated by cementing sand and glass beads with sodium silicate binder. During uniaxial compression tests, the rock samples showed stress-strain behavior which was more similar to that of soils than competent rocks, exhibiting large permanent deformations with frictional slip. The mechanical behavior of the samples approached that of competent rocks as the amount of binder was increased. For very weak samples, acoustic waves propagating in these rocks showed very low velocities of less than 1000 m/sec for compressional waves. A borehole made within this weakly cemented rock exhibited a unique mode of failure that is called ''anti-KI mode fracture'' in this paper. The effect of cementation, grain type, and boundary conditions on this mode of failure was also examined experimentally.

  7. Transcending Portland Cement with 100 percent fly ash concrete

    SciTech Connect (OSTI)

    Cross, D.; Akin, M.; Stephens, J.; Cuelh, E.

    2009-07-01

    The use of concrete, made with 100% fly ash and no Portland cement, in buildings at the Transportation Institute in Bozeman, MT, USA, is described. 3 refs., 7 figs.

  8. Geochemical and Geomechanical Effects on Wellbore Cement Fractures

    SciTech Connect (OSTI)

    Um, Wooyong; Jung, Hun Bok; Kabilan, Senthil; Fernandez, Carlos A.; Brown, Christopher F.

    2014-12-31

    Experimental studies were conducted using batch reactors, X-ray microtomograpy (XMT), and computational fluid dynamics (CFD) simulation to determine changes in cement fracture surfaces, fluid flow pathways, and permeability with geochemical and geomechanical processes. Composite Portland cement-basalt caprock core with artificial fractures was prepared and reacted with CO2-saturated groundwater at 50°C and 10 MPa for 3 to 3.5 months under static conditions to understand the geochemical and geomechanical effects on the integrity of wellbores containing defects. Cement-basalt interface samples were subjected to mechanical stress at 2.7 MPa before the CO2 reaction. XMT provided three-dimensional (3-D) visualization of the opening and interconnection of cement fractures due to mechanical stress. After the CO2 reaction, XMT images revealed that calcium carbonate precipitation occurred extensively within the fractures in the cement matrix, but only partially along fractures located at the cement-basalt interface. The permeability calculated based on CFD simulation was in agreement with the experimentally measured permeability. The experimental results imply that the wellbore cement with fractures is likely to be healed during exposure to CO2-saturated groundwater under static conditions, whereas fractures along the cement-caprock interface are still likely to remain vulnerable to the leakage of CO2. CFD simulation for the flow of different fluids (CO2-saturated brine and supercritical CO2) using a pressure difference of 20 kPa and 200 kPa along ~2 cm-long cement fractures showed that a pressure gradient increase resulted in an increase of CO2 fluids flux by a factor of only ~3-9 because the friction of CO2 fluids on cement fracture surfaces increased with higher flow rate as well. At the same pressure gradient, the simulated flow rate was higher for supercritical CO2 than CO2-saturated brine by a factor of only ~2-3, because the viscosity of supercritical CO2 is much

  9. Geochemical and Geomechanical Effects on Wellbore Cement Fractures

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Um, Wooyong; Jung, Hun Bok; Kabilan, Senthil; Fernandez, Carlos A.; Brown, Christopher F.

    2014-12-31

    Experimental studies were conducted using batch reactors, X-ray microtomograpy (XMT), and computational fluid dynamics (CFD) simulation to determine changes in cement fracture surfaces, fluid flow pathways, and permeability with geochemical and geomechanical processes. Composite Portland cement-basalt caprock core with artificial fractures was prepared and reacted with CO2-saturated groundwater at 50°C and 10 MPa for 3 to 3.5 months under static conditions to understand the geochemical and geomechanical effects on the integrity of wellbores containing defects. Cement-basalt interface samples were subjected to mechanical stress at 2.7 MPa before the CO2 reaction. XMT provided three-dimensional (3-D) visualization of the opening and interconnectionmore » of cement fractures due to mechanical stress. After the CO2 reaction, XMT images revealed that calcium carbonate precipitation occurred extensively within the fractures in the cement matrix, but only partially along fractures located at the cement-basalt interface. The permeability calculated based on CFD simulation was in agreement with the experimentally measured permeability. The experimental results imply that the wellbore cement with fractures is likely to be healed during exposure to CO2-saturated groundwater under static conditions, whereas fractures along the cement-caprock interface are still likely to remain vulnerable to the leakage of CO2. CFD simulation for the flow of different fluids (CO2-saturated brine and supercritical CO2) using a pressure difference of 20 kPa and 200 kPa along ~2 cm-long cement fractures showed that a pressure gradient increase resulted in an increase of CO2 fluids flux by a factor of only ~3-9 because the friction of CO2 fluids on cement fracture surfaces increased with higher flow rate as well. At the same pressure gradient, the simulated flow rate was higher for supercritical CO2 than CO2-saturated brine by a factor of only ~2-3, because the viscosity of supercritical CO2 is

  10. Evaluation of steel furnace slags as cement additives

    SciTech Connect (OSTI)

    Tuefekci, M.; Demirbas, A.; Genc, H.

    1997-11-01

    Chemical and physical properties and strength development have been studied for six granulated steel furnace slags from the normal steelmaking process. This paper reports results of research performed to develop cement mixture proportions using these slags. The influence of slag proportions, specific surface, and water demand on compressive strength and bulk density of cement blends are presented in this paper. The different test results, which were compared with the Turkish Standards, in general, were found to be within the limits.

  11. Multifunctional Corrosion-resistant Foamed Well Cement Composites

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Multifunctional Corrosion-resistant Foamed Well Cement Composites Project Officer: Dan King/Greg Stillman Total budget: $300 K April 24 , 2013 Principal Investigator: Dr. Toshifumi Sugama Co-PI; Dr. Tatiana Pyatina Presenter Name: Dr. Toshifumi Sugama This presentation does not contain any proprietary confidential, or otherwise restricted information. Microstructure developed in conventional foamed (left) and corrosion- resistant foamed cements (right) 2 | US DOE Geothermal Office

  12. Waste tires as auxiliary fuel for cement kilns

    SciTech Connect (OSTI)

    Dodds, J.

    1987-01-01

    The subject I have been asked to speak about is the utilization of scrap tires as an auxiliary fuel for cement kilns. My experience with scrap tires began five years ago when we performed a technical and economic evaluation for tire pyrolysis. I work for the Idaho National Engineering Laboratory which is supported by the Department of Energy. My interest in scrap tires continued; in 1984 the Department of Energy and the Portland Cement Association jointly sponsored a conference on the utilization of scrap tires in cement kilns. Most of my remarks today are based upon that conference along with some current information in the US. Mr. Sladek requested that I speak on the combustion process, the progress to date, and the factors that impede or encourage implementation of using scrap tires in cement kilns. For discussion purposes it would help if we had a common understanding of the cement manufacturing process. Cement is made by heating a mixture of finely ground limestone and silica from clay or sand to about 1450/degree/C in a large rotating kiln. The heat causes the limestone to decarbonate and subsequently react with the silica to form calcium silicates. 5 figs.

  13. Properties and hydration of blended cements with steelmaking slag

    SciTech Connect (OSTI)

    Kourounis, S.; Tsivilis, S. . E-mail: stsiv@central.ntua.gr; Tsakiridis, P.E.; Papadimitriou, G.D.; Tsibouki, Z.

    2007-06-15

    The present research study investigates the properties and hydration of blended cements with steelmaking slag, a by-product of the conversion process of iron to steel. For this purpose, a reference sample and three cements containing up to 45% w/w steel slag were tested. The steel slag fraction used was the '0-5 mm', due to its high content in calcium silicate phases. Initial and final setting time, standard consistency, flow of normal mortar, autoclave expansion and compressive strength at 2, 7, 28 and 90 days were measured. The hydrated products were identified by X-ray diffraction while the non-evaporable water was determined by TGA. The microstructure of the hardened cement pastes and their morphological characteristics were examined by scanning electron microscopy. It is concluded that slag can be used in the production of composite cements of the strength classes 42.5 and 32.5 of EN 197-1. In addition, the slag cements present satisfactory physical properties. The steel slag slows down the hydration of the blended cements, due to the morphology of contained C{sub 2}S and its low content in calcium silicates.

  14. History and some potentials of oil shale cement

    SciTech Connect (OSTI)

    Knutson, C.F.; Smith, R.P.; Russell, B.F. (Idaho National Engineering Lab., Idaho Falls, ID (USA))

    1989-01-01

    The utilization of oil shale as a cement component is discussed. It was investigated in America and Europe during World War I. Additional development occurred in Western Europe, Russia, and China during the 1920s and 1930s. World War II provided further development incentives and a relatively mature technology was in place in Germany, Russia, and China prior to 1980. The utilization of oil shale in cement has taken a number of different paths. One approach has been to utilize the energy in the oil shale as the principal source for the cement plant and to use the combusted shale as a minor constituent of the plant's cement product. A second approach has been to use the combusted shale as a class C or cementitious fly-ash component in portland cement concrete. Other approaches utilizing eastern oil shale have been to use the combusted oil shale with additives as a specialty cement, or to cocombust the oil shale with coal and utilize the sulfur-rich combustion product.

  15. Cement paste prior to setting: A rheological approach

    SciTech Connect (OSTI)

    Bellotto, Maurizio

    2013-10-15

    The evolution of cement paste during the dormant period is analyzed via small amplitude oscillation rheological measurements. Cement paste, from the very first moments after mixing cement and water, shows the formation of an elastic gel whose strength is rapidly increasing over time. Up to the onset of Portlandite precipitation G?(t) increases by more than 2 orders of magnitude and in the acceleratory period G?(t) continues steadily to increase. A microstructural modification is likely to occur between the dormant and the acceleratory period. At low deformations in the linearity domain the storage modulus G?(?) exhibits a negligible frequency dependence. At higher deformations cement paste shows a yield stress which increases on increasing paste concentration. The presence of superplasticizers decreases the yield stress and increases the gelation threshold of the paste. Above the gelation threshold the evolution of cement paste with superplasticizers follows similar trends to the neat paste. -- Highlights: The gelation of cement paste during the dormant period is analyzed via rheometry. The observed evolution is proposed to be related to the pore structure refinement. Similarities are observed with colloidal gels and colloidal glasses.

  16. Potential for energy conservation in the cement industry

    SciTech Connect (OSTI)

    Garrett-Price, B.A.

    1985-02-01

    This report assesses the potential for energy conservation in the cement industry. Energy consumption per ton of cement decreased 20% between 1972 and 1982. During this same period, the cement industry became heavily dependent on coal and coke as its primary fuel source. Although the energy consumed per ton of cement has declined markedly in the past ten years, the industry still uses more than three and a half times the fuel that is theoretically required to produce a ton of clinker. Improving kiln thermal efficiency offers the greatest opportunity for saving fuel. Improving the efficiency of finish grinding offers the greatest potential for reducing electricity use. Technologies are currently available to the cement industry to reduce its average fuel consumption per ton by product by as much as 40% and its electricity consumption per ton by about 10%. The major impediment to adopting these technologies is the cement industry's lack of capital as a result of low or no profits in recent years.

  17. Increasing Energy Efficiency and Reducing Emissions from China's Cement Kilns. Audit Report of Two Cement Plants in Shandong Province, China

    SciTech Connect (OSTI)

    Price, Lynn; Hasanbeigi, Ali; Zhou, Nan; Thekdi, Arvind; Lan, Wang

    2011-07-01

    The study documented in this report was initiated in order to conduct an energy assessment and to identify the relationship between combustion issues and emissions from cement kilns. A new suspension preheater/precalciner (NSP) rotary cement kiln at one cement manufacturing facility (referred to as Shui Ni 1 in this report) and a vertical shaft kiln (VSK) at another cement manufacturing facility (referred to as Shui Ni 2 in this report), which are both in Shandong Province, were selected to conduct the energy and emission assessments through collection of data. Based on analysis of the data collected during this assessment, several actions are suggested that could lead to reduction in coal use and reduction in emission of gaseous pollutants from the system.

  18. Photoneutron logging system for direct uranium ore-grade determination

    SciTech Connect (OSTI)

    Baker, M.P.; Marks, T.

    1982-06-01

    A prototype photoneutron probe for direct uranium assay in exploratory boreholes has been built and field tested. An approx. 10-Ci /sup 124/Sb gamma-ray source together with a beryllium converter is used to produce neutrons that diffuse into the surrounding formation and cause fissions in any /sup 235/U present. The fission neutrons that return to the probe are energy analyzed and counted by a high-pressure helium detector, thus indicating the concentration of uranium. The response of the probe was measured in concrete models at the US Department of Energy (Grand Junction, Colorado) calibration facility and found to be approx. 35 counts/s for an 1% U/sub 3/O/sub 8/ concentration in an 11.4-cm-diam water-filled borehole (4.5 in.). The response is linear up to a concentration of at least 0.25% by weight U/sub 3/O/sub 8/. Effects resulting from changes in formation density, porosity, and neutron absorber content were also quantified, as well as the tool response as a function of borehole diameter and fluid. A logging vehicle was outfitted, and the photoneutron-based logging system was field tested at an exploration site near Canon City, Colorado. Logging data obtained in several open holes at this site are presented and compared to core chemical analyses and results obtained in the same holes using other logging methods. In about 1 month of field testing, the photoneutron-based uranium exploration system has proved to be simple to use and very reliable. 22 figures, 12 tables.

  19. Method of bonding

    DOE Patents [OSTI]

    Saller, deceased, Henry A. (late of Columbus, OH); Hodge, Edwin S. (Columbus, OH); Paprocki, Stanley J. (Columbus, OH); Dayton, Russell W. (Columbus, OH)

    1987-12-01

    1. A method of making a fuel-containing structure for nuclear reactors, comprising providing an assembly comprising a plurality of fuel units; each fuel unit consisting of a core plate containing thermal-neutron-fissionable material, sheets of cladding metal on its bottom and top surfaces, said cladding sheets being of greater width and length than said core plates whereby recesses are formed at the ends and sides of said core plate, and end pieces and first side pieces of cladding metal of the same thickness as the core plate positioned in said recesses, the assembly further comprising a plurality of second side pieces of cladding metal engaging the cladding sheets so as to space the fuel units from one another, and a plurality of filler plates of an acid-dissolvable nonresilient material whose melting point is above 2000.degree. F., each filler plate being arranged between a pair of said second side pieces and the cladding plates of two adjacent fuel units, the filler plates having the same thickness as the second side pieces; the method further comprising enclosing the entire assembly in an envelope; evacuating the interior of the entire assembly through said envelope; applying inert gas under a pressure of about 10,000 psi to the outside of said envelope while at the same time heating the assembly to a temperature above the flow point of the cladding metal but below the melting point of any material of the assembly, whereby the envelope is pressed against the assembly and integral bonds are formed between plates, sheets, first side pieces, and end pieces and between the sheets and the second side pieces; slowly cooling the assembly to room temperature; removing the envelope; and dissolving the filler plates without attacking the cladding metal.

  20. Smart interfacial bonding alloys

    SciTech Connect (OSTI)

    R. Q. Hwang; J. C. Hamilton; J. E. Houston

    1999-04-01

    The goal of this LDRD was to explore the use of the newly discovered strain-stabilized 2-D interfacial alloys as smart interface bonding alloys (SIBA). These materials will be used as templates for the heteroepitaxial growth of metallic thin films. SIBA are formed by two metallic components which mix at an interface to relieve strain and prevent dislocations from forming in subsequent thin film growth. The composition of the SIBA is determined locally by the amount of strain, and therefore can react smartly to areas of the highest strain to relieve dislocations. In this way, SIBA can be used to tailor the dislocation structure of thin films. This project included growth, characterization and modeling of films grown using SIBA templates. Characterization will include atomic imaging of the dislocations structure, measurement of the mechanical properties of the film using interface force microscopy (IFM) and the nanoindenter, and measurement of the electronic structure of the SIBA with synchrotron photoemission. Resistance of films to sulfidation and oxidation will also be examined. The Paragon parallel processing computer will be used to calculate the structure of the SIBA and thin films in order to develop ability to predict and tailor SIBA and thin film behavior. This work will lead to the possible development of a new class of thin film materials with properties tailored by varying the composition of the SIBA, serving as a buffer layer to relieve the strain between the substrate and the thin film. Such films will have improved mechanical and corrosion resistance allowing application as protective barriers for weapons applications. They will also exhibit enhanced electrical conductivity and reduced electromigration making them particularly suitable for application as interconnects and other electronic needs.

  1. 10 Questions with Well-Bore Cement Researcher Dr. Barbara Kutchko |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy with Well-Bore Cement Researcher Dr. Barbara Kutchko 10 Questions with Well-Bore Cement Researcher Dr. Barbara Kutchko March 31, 2015 - 2:53pm Addthis Barbara Kutchko, a well-bore cement researcher, studies the make-up and properties of cement used in oil and gas drilling. | Photo courtesy of the National Energy Technology Lab (NETL). Barbara Kutchko, a well-bore cement researcher, studies the make-up and properties of cement used in oil and gas drilling. | Photo

  2. Method for vacuum fusion bonding

    DOE Patents [OSTI]

    Ackler, Harold D.; Swierkowski, Stefan P.; Tarte, Lisa A.; Hicks, Randall K.

    2001-01-01

    An improved vacuum fusion bonding structure and process for aligned bonding of large area glass plates, patterned with microchannels and access holes and slots, for elevated glass fusion temperatures. Vacuum pumpout of all components is through the bottom platform which yields an untouched, defect free top surface which greatly improves optical access through this smooth surface. Also, a completely non-adherent interlayer, such as graphite, with alignment and location features is located between the main steel platform and the glass plate pair, which makes large improvements in quality, yield, and ease of use, and enables aligned bonding of very large glass structures.

  3. Fusion bonding and alignment fixture

    DOE Patents [OSTI]

    Ackler, Harold D.; Swierkowski, Stefan P.; Tarte, Lisa A.; Hicks, Randall K.

    2000-01-01

    An improved vacuum fusion bonding structure and process for aligned bonding of large area glass plates, patterned with microchannels and access holes and slots, for elevated glass fusion temperatures. Vacuum pumpout of all the components is through the bottom platform which yields an untouched, defect free top surface which greatly improves optical access through this smooth surface. Also, a completely non-adherent interlayer, such as graphite, with alignment and location features is located between the main steel platform and the glass plate pair, which makes large improvements in quality, yield, and ease of use, and enables aligned bonding of very large glass structures.

  4. Effects of setting regulators on the efficiency of an inorganic acid based alkali-free accelerator reacting with a Portland cement

    SciTech Connect (OSTI)

    Maltese, C. . E-mail: Building.lab@mapei.it; Pistolesi, C.; Bravo, A.; Cella, F.; Cerulli, T.; Salvioni, D.

    2007-04-15

    Today, in the field of underground constructions, alkali-free accelerators are commonly employed, during tunnel excavation, to allow flash concrete setting. In this way, the cementitious sprayed material can firmly bond to the tunnel walls, controlling the convergence (the tendency of the section to squeeze). Their efficiency may be related to many parameters like: cement type, setting regulator, concrete composition, working temperature. Nevertheless, the influence of such factors on the accelerator performance has not been clarified yet. The accelerator efficacy is evaluated by real spraying test in job site or, when only laboratory equipment are available, by measuring the final setting times of cement systems admixed with the accelerator. Several alkali-free flash setting admixtures are available on the market. They can be divided into two main categories both containing aluminium sulphate complexes stabilized either by inorganic acids or by organic acids. In this paper, the influence of different setting regulators on the performances of an inorganic acid based alkali-free accelerator was analysed. Portland cement samples were obtained by mixing clinker with gypsum, {alpha}-hemihydrate, {beta}-hemihydrate or anhydrite. The setting regulator instantaneous dissolution rates were evaluated through conductivity measurements. The setting time of cement pastes with and without the accelerator was measured. It was found that the shorter the final setting time (therefore the more efficient is the accelerator) the lower the setting regulator instantaneous dissolution rate. In order to understand this phenomenon, a comparison was performed between accelerated cement paste samples containing the setting regulator with the highest ({beta}-hemihydrate) and the lowest instantaneous dissolution rate (anhydrite). The analytical work included morphological (Environmental Scanning Electron Microscopy-Field Emission Gun - ESEM-FEG), crystal-chemical (X-Ray Powder Diffraction

  5. Public Bonding Options | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Bonding Options Public Bonding Options Traditionally, state and local governments (as well as certain other nonprofit organizations such as universities and hospitals) have had the ability to issue debt, in the form of bonds, to finance construction and/or improvements to public infrastructure. Bonds issued by state and local governments-often referred to as municipal or public bonds-can also be used, under certain circumstances for private activities. Public bonds vary by tax liability, as well

  6. Clean Energy Revenue Bond Program

    Broader source: Energy.gov [DOE]

    The bonds are exempt from taxation by the state, and any type of renewable energy system and most energy efficiency measures, including energy recovery and combined heat and power (CHP) systems,...

  7. The use of scrap tires in rotary cement kilns

    SciTech Connect (OSTI)

    Blumenthal, M.

    1996-12-31

    The use of scrap tires as a supplemental fuel in the United States Portland cement industry has increased significantly in the past six years. In 1990, there were two kilns using tire-derived fuel (TDF), today 30 kilns use TDF. The outlook for continued and expanded use of TDF in the U.S. cement industry should be considered favorable, with 15 kilns conducting tests to determine TDF`s applicability or in the permitting process. The Council`s estimates are that by the end of 1996, the cement industry could be consuming some 75-100 million of the 253 million annually generated scrap tires in the United States. This level of TDF usage will make the cement industry the largest market segments for scrap tires in the United States. While the long-term outlook is at present positive, there are a series of factors that have, and will likely continue to adversely impact the near-term usage of TDF. These issues, as well as the factors that are likely to positively impact the cement kiln TDF market are the subject of this presentation.

  8. Method to improve commercial bonded SOI material

    DOE Patents [OSTI]

    Maris, Humphrey John; Sadana, Devendra Kumar

    2000-07-11

    A method of improving the bonding characteristics of a previously bonded silicon on insulator (SOI) structure is provided. The improvement in the bonding characteristics is achieved in the present invention by, optionally, forming an oxide cap layer on the silicon surface of the bonded SOI structure and then annealing either the uncapped or oxide capped structure in a slightly oxidizing ambient at temperatures greater than 1200.degree. C. Also provided herein is a method for detecting the bonding characteristics of previously bonded SOI structures. According to this aspect of the present invention, a pico-second laser pulse technique is employed to determine the bonding imperfections of previously bonded SOI structures.

  9. Low Temperature Material Bonding Techniq Ue

    DOE Patents [OSTI]

    Ramsey, J. Michael; Foote, Robert S.

    2002-08-06

    A method of performing a lower temperature bonding technique to bond together two mating pieces of glass includes applying a sodium silicate aqueous solution between the two pieces.

  10. Covalent Bonding in Actinide Sandwich Molecules

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    describe bonding in organometallics are at frequently at odds with classical coordination chemistry, in that they invoke a covalent bond between the metal and the carbon-based...

  11. Local Option- Industrial Facilities and Development Bonds

    Broader source: Energy.gov [DOE]

    Under the Utah Industrial Facilities and Development Act, counties, municipalities, and state universities in Utah may issue Industrial Revenue Bonds (IRBs) or Industrial Development Bonds (IDBs)...

  12. E-print Network Web Log News: Research Communications for Scientists...

    Office of Scientific and Technical Information (OSTI)

    Description This Web Log provides the latest information about changes to E-print Network ... questions, concerns and other input by using the Contact Us page. Web Log Archive

  13. AmeriFlux BR-Sa3 Santarem-Km83-Logged Forest

    SciTech Connect (OSTI)

    Goulden, Mike

    2016-01-01

    This is the AmeriFlux version of the carbon flux data for the site BR-Sa3 Santarem-Km83-Logged Forest. Site Description - Cleared forest. Logged site is near km 83 along BR-183.

  14. New Clean Renewable Energy Bonds | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    New Clean Renewable Energy Bonds New Clean Renewable Energy Bonds New clean renewable energy bonds (CREBs) are tax credit bonds, the proceeds of which are used for capital ...

  15. Logging into Deltek Time & Expense (T&E) | The Ames Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Logging into Deltek Time & Expense (T&E) Document Number: NA Effective Date: 07/2014

  16. High voltage supply for neutron tubes in well logging applications

    DOE Patents [OSTI]

    Humphreys, D. Russell

    1989-01-01

    A high voltage supply is provided for a neutron tube used in well logging. The "biased pulse" supply of the invention combines DC and "full pulse" techniques and produces a target voltage comprising a substantial negative DC bias component on which is superimposed a pulse whose negative peak provides the desired negative voltage level for the neutron tube. The target voltage is preferably generated using voltage doubling techniques and employing a voltage source which generates bipolar pulse pairs having an amplitude corresponding to the DC bias level.

  17. Bond strength of cementitious borehole plugs in welded tuff

    SciTech Connect (OSTI)

    Akgun, H.; Daemen, J.J.K.

    1991-02-01

    Axial loads on plugs or seals in an underground repository due to gas, water pressures and temperature changes induced subsequent to waste and plug emplacement lead to shear stresses at the plug/rock contact. Therefore, the bond between the plug and rock is a critical element for the design and effectiveness of plugs in boreholes, shafts or tunnels. This study includes a systematic investigation of the bond strength of cementitious borehole plugs in welded tuff. Analytical and numerical analysis of borehole plug-rock stress transfer mechanics is performed. The interface strength and deformation are studied as a function of Young`s modulus ratio of plug and rock, plug length and rock cylinder outside-to-inside radius ratio. The tensile stresses in and near an axially loaded plug are analyzed. The frictional interface strength of an axially loaded borehole plug, the effect of axial stress and lateral external stress, and thermal effects are also analyzed. Implications for plug design are discussed. The main conclusion is a strong recommendation to design friction plugs in shafts, drifts, tunnels or boreholes with a minimum length to diameter ratio of four. Such a geometrical design will reduce tensile stresses in the plug and in the host rock to a level which should minimize the risk of long-term deterioration caused by excessive tensile stresses. Push-out tests have been used to determine the bond strength by applying an axial load to cement plugs emplaced in boreholes in welded tuff cylinders. A total of 130 push-out tests have been performed as a function of borehole size, plug length, temperature, and degree of saturation of the host tuff. The use of four different borehole radii enables evaluation of size effects. 119 refs., 42 figs., 20 tabs.

  18. Recommended guidelines for solid fuel use in cement plants

    SciTech Connect (OSTI)

    Young, G.L.; Jayaraman, H.; Tseng, H.

    2007-07-01

    Pulverized solid fuel use at cement plants in North America is universal and includes bituminous and sub-bituminous coal, petroleum coke, and any combination of these materials. Provided are guidelines for the safe use of pulverized solid fuel systems in cement plants, including discussion of the National Fire Protection Association and FM Global fire and explosion prevention standards. Addressed are fire and explosion hazards related to solid fuel use in the cement industry, fuel handling and fuel system descriptions, engineering design theory, kiln system operations, electrical equipment, instrumentation and safety interlock issues, maintenance and training, and a brief review of code issues. New technology on fire and explosion prevention including deflagration venting is also presented.

  19. Hydration of Portland cement with additions of calcium sulfoaluminates

    SciTech Connect (OSTI)

    Le Saout, Gwenn; Lothenbach, Barbara; Hori, Akihiro; Higuchi, Takayuki; Winnefeld, Frank

    2013-01-15

    The effect of mineral additions based on calcium aluminates on the hydration mechanism of ordinary Portland cement (OPC) was investigated using isothermal calorimetry, thermal analysis, X-ray diffraction, scanning electron microscopy, solid state nuclear magnetic resonance and pore solution analysis. Results show that the addition of a calcium sulfoaluminate cement (CSA) to the OPC does not affect the hydration mechanism of alite but controls the aluminate dissolution. In the second blend investigated, a rapid setting cement, the amorphous calcium aluminate reacts very fast to ettringite. The release of aluminum ions strongly retards the hydration of alite but the C-S-H has a similar composition as in OPC with no additional Al to Si substitution. As in CSA-OPC, the aluminate hydration is controlled by the availability of sulfates. The coupling of thermodynamic modeling with the kinetic equations predicts the amount of hydrates and pore solution compositions as a function of time and validates the model in these systems.

  20. Cement-aggregate compatibility and structure property relationships including modelling

    SciTech Connect (OSTI)

    Jennings, H.M.; Xi, Y.

    1993-07-15

    The role of aggregate, and its interface with cement paste, is discussed with a view toward establishing models that relate structure to properties. Both short (nm) and long (mm) range structure must be considered. The short range structure of the interface depends not only on the physical distribution of the various phases, but also on moisture content and reactivity of aggregate. Changes that occur on drying, i.e. shrinkage, may alter the structure which, in turn, feeds back to alter further drying and shrinkage. The interaction is dynamic, even without further hydration of cement paste, and the dynamic characteristic must be considered in order to fully understand and model its contribution to properties. Microstructure and properties are two subjects which have been pursued somewhat separately. This review discusses both disciplines with a view toward finding common research goals in the future. Finally, comment is made on possible chemical reactions which may occur between aggregate and cement paste.

  1. A comparison of normal and worst case cement plant emissions

    SciTech Connect (OSTI)

    Woodford, J.; Gossman, D.; Johnson, N.

    1996-12-31

    Lone Star Industries, Inc. in Cape Girardeau, Missouri conducted a trial burn in October, 1995. Two metals emissions test days were conducted. One of the test days was a worst case metals spiking day and one of the test days was a normal emissions day. This paper examines and compares the emissions from these two test days. Much has been made of metals emissions from hazardous waste burning cement kilns, but for the most part, this has been due to the worst case metals emissions data that became available from the 1992 BIF compliance testing performed and reported by 24 cement plants. By comparison, very little data exists on normal cement kiln emissions. This paper provides one comparison.

  2. Degree of dispersion of latex particles in cement paste, as assessed by electrical resistivity measurement

    SciTech Connect (OSTI)

    Fu, X.; Chung, D.D.L.

    1996-12-31

    The degree of dispersion of latex particles in latex-modified cement paste was assessed by measurement of the volume electrical resistivity and modeling this resistivity in terms of latex and cement phases that are partly in series and partly in parallel. The assessment was best at low values of the latex-cement ratio; it underestimated the degree of latex dispersion when the latex/cement ratio was high, especially > 0.2.

  3. FORTE log periodic antenna. Phase 1, Final report

    SciTech Connect (OSTI)

    Not Available

    1993-04-22

    This report summarizes the results of ABLE`s design study of the FORTE deployable log periodic antenna. The resulting Baseline Design of the antenna is the basis for ABLE`s proposal for Phase II of this program. ABLE`s approach to meeting the requirements is to use a coilable ABLE mast as the deployable structure ``backbone`` of the antenna and to use deployable tubes for. the log periodic dipole elements of the antenna. This general approach was adopted at the outset of the Phase I Design Study. The remainder of the study was devoted to detailed design and analysis to properly size these types of mast and antenna elements and to design their deployment mechanisms. Demonstration models of the mast and antenna element deployer were fabricated as part of Phase I study. The study showed that ABLE`s design approach is feasible and can meet all the specified design requirements except the mass limit of 13.5 kg. Results of the design and analysis studies are summarized in this report. The mast and dipole element deployer are to be demonstrated to LANL personnel at the conclusion of this Phase I study.

  4. Temperature influence on water transport in hardened cement pastes

    SciTech Connect (OSTI)

    Drouet, Emeline; Poyet, Stéphane; Torrenti, Jean-Michel

    2015-10-15

    Describing water transport in concrete is an important issue for the durability assessment of radioactive waste management reinforced concrete structures. Due to the waste thermal output such structures would be submitted to moderate temperatures (up to 80 °C). We have then studied the influence of temperature on water transport within hardened cement pastes of four different formulations. Using a simplified approach (describing only the permeation of liquid water) we characterized the properties needed to describe water transport (up to 80 °C) using dedicated experiments. For each hardened cement paste the results are presented and discussed.

  5. Lehigh Southwest Cement Company: Compressed Air System Improvement Saves Energy

    SciTech Connect (OSTI)

    2003-10-01

    In 2001, Lehigh Southwest Cement Company improved the compressed air system at its cement plant in Tehachapi, California. Consequently, the system was able to operate more efficiently with less compressor capacity and at a lower system pressure. The project yielded total annual savings of 895,000 kWh and $199,000. The initial project cost was $417,000, but Southern California Edison provided a $90,000 incentive payment to reduce the cost to $327,000. Simple payback was about 20 months.

  6. Chromium stabilization chemistry of paint removal wastes in Portland cement and blast furnace slag

    SciTech Connect (OSTI)

    Boy, J.H.; Race, T.D.; Reinbold, K.A.

    1995-12-31

    The use of cement based systems for solidification and stabilization of hazardous wastes has been proposed. The stabilization of Cr contaminated paint removal wastes in ordinary Portland cement and in a Portland cement and blast furnace slag matrix was investigated. A loading by volume of 75% waste and 25% cement (or cement + slag) was used. The expression of pore solution was utilized to determine the chemical environment encountered by the waste species in the cement matrix. The highly alkaline conditions of ordinary Portland cement determined the stability of the metal species, with Cr being highly soluble. The replacement of 25% of the Portland cement by blast furnace slag was found to decrease the [OH-] of the pore solution resulting in a decrease of the Cr concentration. For cement wastes forms hydrated for 28 days, the Cr concentration decreased in the expressed pore solution. During the TCLP tests the cement waste form and extraction solution were found to react, changing the chemistry of the extraction solution. The expression of pore solution was found to give a direct measure of the chemistry of the waste species in the cement matrix. This avoids the reaction of the TCLP extraction solution with the cement matrix which changes the solubility of the hazardous metals. 15 refs., 4 figs., 6 tabs.

  7. METHOD FOR PRODUCING CEMENTED CARBIDE ARTICLES

    DOE Patents [OSTI]

    Onstott, E.I.; Cremer, G.D.

    1959-07-14

    A method is described for making molded materials of intricate shape where the materials consist of mixtures of one or more hard metal carbides or oxides and matrix metals or binder metals thereof. In one embodiment of the invention 90% of finely comminuted tungsten carbide powder together with finely comminuted cobalt bonding agent is incorporated at 60 deg C into a slurry with methyl alcohol containing 1.5% paraffin, 3% camphor, 3.5% naphthalene, and 1.8% toluene. The compact is formed by the steps of placing the slurry in a mold at least one surface of which is porous to the fluid organic system, compacting the slurry, removing a portion of the mold from contact with the formed object and heating the formed object to remove the remaining organic matter and to sinter the compact.

  8. Transient liquid phase ceramic bonding

    DOE Patents [OSTI]

    Glaeser, Andreas M. (Berkeley, CA)

    1994-01-01

    Ceramics are joined to themselves or to metals using a transient liquid phase method employing three layers, one of which is a refractory metal, ceramic or alloy. The refractory layer is placed between two metal layers, each of which has a lower melting point than the refractory layer. The three layers are pressed between the two articles to be bonded to form an assembly. The assembly is heated to a bonding temperature at which the refractory layer remains solid, but the two metal layers melt to form a liquid. The refractory layer reacts with the surrounding liquid and a single solid bonding layer is eventually formed. The layers may be designed to react completely with each other and form refractory intermetallic bonding layers. Impurities incorporated into the refractory metal may react with the metal layers to form refractory compounds. Another method for joining ceramic articles employs a ceramic interlayer sandwiched between two metal layers. In alternative embodiments, the metal layers may include sublayers. A method is also provided for joining two ceramic articles using a single interlayer. An alternate bonding method provides a refractory-metal oxide interlayer placed adjacent to a strong oxide former. Aluminum or aluminum alloys are joined together using metal interlayers.

  9. Mercury stabilization in chemically bonded phosphate ceramics

    SciTech Connect (OSTI)

    Wagh, A. S.; Singh, D.; Jeong, S. Y.

    2000-04-04

    Mercury stabilization and solidification is a significant challenge for conventional stabilization technologies. This is because of the stringent regulatory limits on leaching of its stabilized products. In a conventional cement stabilization process, Hg is converted at high pH to its hydroxide, which is not a very insoluble compound; hence the preferred route for Hg sulfidation to convert it into insoluble cinnabar (HgS). Unfortunately, efficient formation of this compound is pH-dependent. At a high pH, one obtains a more soluble Hg sulfate, in a very low pH range, insufficient immobilization occurs because of the escape of hydrogen sulfide, while efficient formation of HgS occurs only in a moderately acidic region. Thus, the pH range of 4 to 8 is where stabilization with Chemically Bonded Phosphate Ceramics (CBPC) is carried out. This paper discusses the authors experience on bench-scale stabilization of various US Department of Energy (DOE) waste streams containing Hg in the CBPC process. This process was developed to treat DOE's mixed waste streams. It is a room-temperature-setting process based on an acid-base reaction between magnesium oxide and monopotassium phosphate solution that forms a dense ceramic within hours. For Hg stabilization, addition of a small amount (< 1 wt.%) of Na{sub 2}S or K{sub 2}S is sufficient in the binder composition. Here the Toxicity Characteristic Leaching Procedure (TCLP) results on CBPC waste forms of surrogate waste streams representing secondary Hg containing wastes such as combustion residues and Delphi DETOX{trademark} residues are presented. The results show that although the current limit on leaching of Hg is 0.2 mg/L, the results from the CBPC waste forms are at least one order lower than this stringent limit. Encouraged by these results on surrogate wastes, they treated actual low-level Hg-containing mixed waste from their facility at Idaho. TCLP results on this waste are presented here. The efficient stabilization in

  10. INFORMATION REGARDING PERFORMANCE AND PAYMENT BONDS

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    C&BS Form Date: 5-20-2015 1 INFORMATION REGARDING PERFORMANCE AND PAYMENT BONDS I. PERFORMANCE BOND A performance bond secures performance and fulfillment of the Subcontractor's obligations under the subcontract. A performance bond is required in accordance with this subcontract. The Subcontractor shall submit the performance bond to the subcontract administrator within five (5) calendar days after notification of award and prior to starting work for any subcontract exceeding $30,000.00. The

  11. Factors affecting the behavior of bentonite fluids and their in-situ conversion into cement. Final report

    SciTech Connect (OSTI)

    Gueven, N.; Carney, L.L.; Malekahmadi, F.; Lee, L.J.

    1984-11-01

    To develop a basic understanding of the effects of common salts, hydroxides, and other mud additives on the rheology and other functions of bentonite fluids, bentonite fluids containing these additives were autoclaved at the temperature range 70 to 600/sup 0/F, and under a pressure of 17,000 psi. Subsequently, the high-temperature rheology of the fluids was measured with a FANN 50C viscometer. Other fluid properties such as plastic viscosity, gel strength, yield point, pH, CEC, and fluid losses were also determined before and after autoclaving of the fluids. The high-temperature reactions occurring in these fluids were studied with x-ray diffraction and electron microscopy. Another costly problem in drilling technology is related to the poor cement bonding of the casing to the formation. As a solution to this troublesome situation, the in-situ conversion of bentonite fluids into cement has been studied. This conversion has been successfully achieved by the addition of lime to bentonite fluids at and above 300/sup 0/F.

  12. Westinghouse Cementation Facility of Solid Waste Treatment System - 13503

    SciTech Connect (OSTI)

    Jacobs, Torsten; Aign, Joerg

    2013-07-01

    During NPP operation, several waste streams are generated, caused by different technical and physical processes. Besides others, liquid waste represents one of the major types of waste. Depending on national regulation for storage and disposal of radioactive waste, solidification can be one specific requirement. To accommodate the global request for waste treatment systems Westinghouse developed several specific treatment processes for the different types of waste. In the period of 2006 to 2008 Westinghouse awarded several contracts for the design and delivery of waste treatment systems related to the latest CPR-1000 nuclear power plants. One of these contracts contains the delivery of four Cementation Facilities for waste treatment, s.c. 'Follow on Cementations' dedicated to three locations, HongYanHe, NingDe and YangJiang, of new CPR-1000 nuclear power stations in the People's Republic of China. Previously, Westinghouse delivered a similar cementation facility to the CPR-1000 plant LingAo II, in Daya Bay, PR China. This plant already passed the hot functioning tests successfully in June 2012 and is now ready and released for regular operation. The 'Follow on plants' are designed to package three 'typical' kind of radioactive waste: evaporator concentrates, spent resins and filter cartridges. The purpose of this paper is to provide an overview on the Westinghouse experience to design and execution of cementation facilities. (authors)

  13. New pulsating casing collar to improve cementing quality

    SciTech Connect (OSTI)

    Chen, P.; He, K.; Wu, J.

    1998-12-31

    This paper presents the design and test results of a new pulsating casing collar which improves cementing quality. The new pulsating casing collar (PCC) is designed according to the Helmholtz oscillator to generate a pulsating jet flow by self-excitation in the cementing process. By placing this new pulsating casing collar at the bottom of casing string, the generated pulsating jet flow transmits vibrating pressure waves up through the annulus and helps remove drilling mud in the annulus. It can therefore improve cementing quality, especially when eccentric annulus exists due to casing eccentricity where the mud is difficult to remove. The new pulsating casing collar consists of a top nozzle, a resonant chamber, and a bottom nozzle. It can be manufactured easily and is easy to use in the field. It has been tested in Jianghan oil-field, P.R. China. The field-test results support the theoretical analysis and laboratory test, and the cementing quality is shown greatly improved by using the new pulsating casing collar.

  14. Hydrocarbon segregation from well logs, Northern Monagas, Venezuela

    SciTech Connect (OSTI)

    Garcia, E. )

    1993-02-01

    A methodology is described to determine vertical hydrocarbon density variations in recent oil discoveries in Northern Monagas state, using well logs. Similarities and differences are established for models obtained in El Carito and El Tejero fault block-s. These models were confirmed using independent information, such as PVT analysis, RFT pressures, oil gravity and GOR's from initial production tests. To explain differences between the models, an hypothesis is proposed for the migration/segregation/deformation sequence in these two blocks, which accounts for the presence of lighter hydrocarbons in El Tejero block, even though it is 1700 ft structurally lower than El Carito. Based on this hypothesis, westward projection of the models predicts lighter hydrocarbons and similar porosities for Casupal-Mata Granda and Tonoro blocks, at depths considerably greater than in El Tejero block.

  15. Experimental study of the relationship between formation factor, porosity, and cementation

    SciTech Connect (OSTI)

    Harig, M.D.; Chaney, R.C.

    1999-07-01

    Cemented granular soils are classified based on the size and distribution of the individual grains and qualitatively on the basis of cementation. To uniquely classify these types of soils, information about the fabric (pore geometry and/or level of cementation) of the specimen needs to be quantified. Electrical resistivity, or its reciprocal, conductivity, methods have been extensively used both in situ and in the laboratory to provide a means for determining a variety of soil index, structural, erosional, and cyclic properties. The objective of this study was to determine the relationship between formation factor (F), porosity (n), and cementation factor (m) of remolded sand-cement specimens. This relationship is shown to provide a mechanism for estimating the level of cementation in undisturbed specimens. The formation factor is the ratio of the electrical resistivity of the sand-water-cement mixture to that of the interstitial water.

  16. Bonded polyimide fuel cell package

    DOE Patents [OSTI]

    Morse, Jeffrey D.; Jankowski, Alan; Graff, Robert T.; Bettencourt, Kerry

    2010-06-08

    Described herein are processes for fabricating microfluidic fuel cell systems with embedded components in which micron-scale features are formed by bonding layers of DuPont Kapton.TM. polyimide laminate. A microfluidic fuel cell system fabricated using this process is also described.

  17. Non-bonded ultrasonic transducer

    DOE Patents [OSTI]

    Eoff, J.M.

    1984-07-06

    A mechanically assembled non-bonded ultrasonic transducer includes a substrate, a piezoelectric film, a wetting agent, a thin metal electrode, and a lens held in intimate contact by a mechanical clamp. No epoxy or glue is used in the assembly of this device.

  18. New Mexico Play Fairway Analysis: Gamma Ray Logs and Heat Generation Calculations for SW New Mexico

    SciTech Connect (OSTI)

    Shari Kelley

    2015-10-23

    For the New Mexico Play fairway Analysis project, gamma ray geophysical well logs from oil wells penetrating the Proterozoic basement in southwestern New Mexico were digitized. Only the portion of the log in the basement was digitized. The gamma ray logs are converted to heat production using the equation (Bucker and Rybach, 1996) : A[µW/m3] = 0.0158 (Gamma Ray [API] – 0.8).

  19. Nonprofit Organizations: Have Your Los Alamos Employees/Retirees Log Hours

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    in VolunteerMatch Nonprofit Organizations: Have Your Los Alamos Employees/Retirees Log Hours in VolunteerMatch Community Connections: Your link to news and opportunities from Los Alamos National Laboratory Latest Issue: September 1, 2016 all issues All Issues » submit Nonprofit Organizations: Have Your Los Alamos Employees/Retirees Log Hours in VolunteerMatch Lab employees and retirees should log their VolunteerMatch hours to benefit local nonprofits. March 1, 2013 Volunteers help fill

  20. Opportunities for Energy Efficiency and Demand Response in the California Cement Industry

    SciTech Connect (OSTI)

    Olsen, Daniel; Goli, Sasank; Faulkner, David; McKane, Aimee

    2010-12-22

    This study examines the characteristics of cement plants and their ability to shed or shift load to participate in demand response (DR). Relevant factors investigated include the various equipment and processes used to make cement, the operational limitations cement plants are subject to, and the quantities and sources of energy used in the cement-making process. Opportunities for energy efficiency improvements are also reviewed. The results suggest that cement plants are good candidates for DR participation. The cement industry consumes over 400 trillion Btu of energy annually in the United States, and consumes over 150 MW of electricity in California alone. The chemical reactions required to make cement occur only in the cement kiln, and intermediate products are routinely stored between processing stages without negative effects. Cement plants also operate continuously for months at a time between shutdowns, allowing flexibility in operational scheduling. In addition, several examples of cement plants altering their electricity consumption based on utility incentives are discussed. Further study is needed to determine the practical potential for automated demand response (Auto-DR) and to investigate the magnitude and shape of achievable sheds and shifts.

  1. Density Log at Fish Lake Valley Area (DOE GTP) | Open Energy...

    Open Energy Info (EERE)

    Fish Lake Valley Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Density Log at Fish Lake Valley Area (DOE GTP) Exploration...

  2. Resistivity Log At Fish Lake Valley Area (DOE GTP) | Open Energy...

    Open Energy Info (EERE)

    Fish Lake Valley Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Resistivity Log At Fish Lake Valley Area (DOE GTP) Exploration...

  3. Well Log Data At Dixie Valley Geothermal Area (Mallan, Et Al...

    Open Energy Info (EERE)

    conducted to help characterize the geothermal reservoir by employing electromagnetic induction logging. The goal was to discern subsurface features that are useful in geothermal...

  4. FMI Log At Glass Buttes Area (DOE GTP) | Open Energy Information

    Open Energy Info (EERE)

    Glass Buttes Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: FMI Log At Glass Buttes Area (DOE GTP) Exploration Activity Details...

  5. Gamma Log At Flint Geothermal Area (DOE GTP) | Open Energy Information

    Open Energy Info (EERE)

    Flint Geothermal Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Gamma Log At Flint Geothermal Area (DOE GTP) Exploration Activity...

  6. Gamma Log At Silver Peak Area (DOE GTP) | Open Energy Information

    Open Energy Info (EERE)

    Silver Peak Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Gamma Log At Silver Peak Area (DOE GTP) Exploration Activity Details...

  7. Resistivity Log At Fort Bliss Area (DOE GTP) | Open Energy Information

    Open Energy Info (EERE)

    DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Resistivity Log At Fort Bliss Area (DOE GTP) Exploration Activity Details Location Fort...

  8. Neutron Log At Silver Peak Area (DOE GTP) | Open Energy Information

    Open Energy Info (EERE)

    Silver Peak Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Neutron Log At Silver Peak Area (DOE GTP) Exploration Activity Details...

  9. Acoustic Logs At The Needles Area (DOE GTP) | Open Energy Information

    Open Energy Info (EERE)

    The Needles Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Acoustic Logs At The Needles Area (DOE GTP) Exploration Activity...

  10. Resistivity Log At The Needles Area (DOE GTP) | Open Energy Informatio...

    Open Energy Info (EERE)

    The Needles Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Resistivity Log At The Needles Area (DOE GTP) Exploration Activity...

  11. Cross-Dipole Acoustic Log At Alum Area (Moos & Ronne, 2010) ...

    Open Energy Info (EERE)

    oriented in the strike direction of the fault and of the dipping sediments. References Daniel Moos, Joel Ronne (2010) Selecting The Optimal Logging Suite For Geothermal Reservoir...

  12. Resistivity Log At Fort Bliss Area (Combs, Et Al., 1999) | Open...

    Open Energy Info (EERE)

    well. A suite of geophysical logs (gamma ray, neutron, sonic, and resistivity) was also run after completion of drilling. References Jim Combs, John T. Finger, Colin Goranson,...

  13. Gamma Log At Fort Bliss Area (Combs, Et Al., 1999) | Open Energy...

    Open Energy Info (EERE)

    well. A suite of geophysical logs (gamma ray, neutron, sonic, and resistivity) was also run after completion of drilling. References Jim Combs, John T. Finger, Colin Goranson,...

  14. Neutron Log At Fort Bliss Area (Combs, Et Al., 1999) | Open Energy...

    Open Energy Info (EERE)

    well. A suite of geophysical logs (gamma ray, neutron, sonic, and resistivity) was also run after completion of drilling. References Jim Combs, John T. Finger, Colin Goranson,...

  15. Pressure Temperature Log At Soda Lake Area (DOE GTP) | Open Energy...

    Open Energy Info (EERE)

    navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Pressure Temperature Log At Soda Lake Area (DOE GTP) Exploration Activity Details Location Soda Lake...

  16. Well Log Techniques At Snake River Plain Region (DOE GTP) | Open...

    Open Energy Info (EERE)

    navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Well Log Techniques At Snake River Plain Region (DOE GTP) Exploration Activity Details Location Snake...

  17. Well Log Data At Dixie Valley Geothermal Area (Barton, Et Al...

    Open Energy Info (EERE)

    Exploration Basis Well log data was used to investigate the relationship between permeability and the contemporary in situ stress field in the Dixie Valley Geothermal Reservoir....

  18. FMI Log At New River Area (DOE GTP) | Open Energy Information

    Open Energy Info (EERE)

    GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: FMI Log At New River Area (DOE GTP) Exploration Activity Details Location New River Area...

  19. Density Log at Gabbs Valley Area (DOE GTP) | Open Energy Information

    Open Energy Info (EERE)

    Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Density Log at Gabbs Valley Area (DOE GTP) Exploration Activity Details Location Gabbs Valley...

  20. Density Log at Fort Bliss Area (DOE GTP) | Open Energy Information

    Open Energy Info (EERE)

    Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Density Log at Fort Bliss Area (DOE GTP) Exploration Activity Details Location Fort Bliss...

  1. Density Log at Silver Peak Area (DOE GTP) | Open Energy Information

    Open Energy Info (EERE)

    Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Density Log at Silver Peak Area (DOE GTP) Exploration Activity Details Location Silver Peak...

  2. Density Log at Alum Area (Moos & Ronne, 2010) | Open Energy Informatio...

    Open Energy Info (EERE)

    Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Density Log at Alum Area (Moos & Ronne, 2010) Exploration Activity Details Location Alum...

  3. Hi Bond Tapes Ltd | Open Energy Information

    Open Energy Info (EERE)

    Hi Bond Tapes Ltd Jump to: navigation, search Name: Hi-Bond Tapes Ltd Place: Northamptonshire, England, United Kingdom Zip: NN17 5TS Product: Northamptonshire-based supplier of...

  4. Calibration models for density borehole logging - construction report

    SciTech Connect (OSTI)

    Engelmann, R.E.; Lewis, R.E.; Stromswold, D.C.

    1995-10-01

    Two machined blocks of magnesium and aluminum alloys form the basis for Hanford`s density models. The blocks provide known densities of 1.780 {plus_minus} 0.002 g/cm{sup 3} and 2.804 {plus_minus} 0.002 g/cm{sup 3} for calibrating borehole logging tools that measure density based on gamma-ray scattering from a source in the tool. Each block is approximately 33 x 58 x 91 cm (13 x 23 x 36 in.) with cylindrical grooves cut into the sides of the blocks to hold steel casings of inner diameter 15 cm (6 in.) and 20 cm (8 in.). Spacers that can be inserted between the blocks and casings can create air gaps of thickness 0.64, 1.3, 1.9, and 2.5 cm (0.25, 0.5, 0.75 and 1.0 in.), simulating air gaps that can occur in actual wells from hole enlargements behind the casing.

  5. Fluid-Rock Characterization and Interactions in NMR Well Logging

    SciTech Connect (OSTI)

    Hirasaki, George J.; Mohanty, Kishore, K.

    2001-07-13

    The objective of this project is to characterize the fluid properties and fluid-rock interactions that are needed for formation evaluation by NMR well logging. This is the first annual progress report submitted to the DOE. It reports on the work completed during the reporting period even if it may have started before this period. This project is a partnership between Professor George J. Hirasaki at Rice University and Professor Kishore Mohanty at University of Houston. In addition to the DOE, this project is supported by a consortium of oil companies and service companies. The fluid properties characterization has emphasized the departure of live oils from correlations based on dead oils. Also, asphaltic components can result in a difference between the T1 and T2 relaxation time distributions as well as reduce the hydrogen index. The fluid rock characterizations that are reported here are the effects of wettability and internal magnetic field gradients. A pore reconstruction method ha s been developed to recreate three-dimensional porous media from two-dimensional images that reproduce some of their key statistical properties. A Monte Carlo simulation technique has been developed to calculate the magnetization decay in fluid saturated porous media given their pore structure.

  6. Bonded, walk-off compensated optical elements

    DOE Patents [OSTI]

    Ebbers, Christopher A.

    2003-04-08

    A bonded, walk-off compensated crystal, for use with optical equipment, and methods of making optical components including same.

  7. Covalent Bonding in Actinide Sandwich Molecules

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Covalent Bonding in Actinide Sandwich Molecules Covalent Bonding in Actinide Sandwich Molecules Print Wednesday, 28 May 2014 00:00 Glenn Seaborg was one of the first scientists to recognize that differences in the degree of covalent bonding in lanthanide and actinide compounds could have profound consequences for their unique chemical reactivity and physical properties. Now, researchers working at ALS Beamline 11.0.2 have found evidence for unexpected bonding interactions in two organometallic

  8. Effect of large additions of Cd, Pb, Cr, Zn, to cement raw meal on the composition and the properties of the clinker and the cement

    SciTech Connect (OSTI)

    Murat, M.; Sorrentino, F.

    1996-03-01

    The utilization of hydraulic binders to solidify and to stabilize industrial wastes and municipal garbage is presently recognized as one of the solutions to the problem of environment protection. Te addition of important quantities of Cd, Pb, Cr, Zn to raw meals of Portland and calcium aluminate cement modifies the mineralogical composition and the properties of the final cement. Portland cement can absorb a large amount of Cd and Zn. This absorption leads to an increase of setting time and a decrease of strengths of the cement. It also can trap chromium with a short setting time and high strengths. Calcium aluminate cements easily trap Cd and Cr with a delayed setting and good strength but also Pb with normal setting time and strengths. Large quantities of zinc oxide have a deleterious effect on calcium aluminate strengths.

  9. Rheology of Carbon Fibre Reinforced Cement-Based Mortar

    SciTech Connect (OSTI)

    Banfill, Phillip F. G.; Starrs, Gerry; McCarter, W. John [School of the Built Environment, Heriot-Watt University, Edinburgh, EH14 4AS (United Kingdom)

    2008-07-07

    Carbon fibre reinforced cement based materials (CFRCs) offer the possibility of fabricating 'smart' electrically conductive materials. Rheology of the fresh mix is crucial to satisfactory moulding and fresh CFRC conforms to the Bingham model with slight structural breakdown. Both yield stress and plastic viscosity increase with increasing fibre length and volume concentration. Using a modified Viskomat NT, the concentration dependence of CFRC rheology up to 1.5% fibre volume is reported.

  10. Hard x-ray nanotomography of amorphous aluminosilicate cements.

    SciTech Connect (OSTI)

    Provis, J. L.; Rose, V.; Winarski, R. P.; van Deventer, J. S. J.

    2011-08-01

    Nanotomographic reconstruction of a sample of low-CO{sub 2} 'geopolymer' cement provides the first three-dimensional view of the pore structure of the aluminosilicate geopolymer gel, as well as evidence for direct binding of geopolymer gel onto unreacted fly ash precursor particles. This is central to understanding and optimizing the durability of concretes made using this new class of binder, and demonstrates the value of nanotomography in providing a three-dimensional view of nanoporous inorganic materials.

  11. Analysis of Energy-Efficiency Opportunities for the Cement Industry in Shandong Province, China

    SciTech Connect (OSTI)

    Price, Lynn; Hasanbeigi, Ali; Lu, Hongyou; Wang, Lan

    2009-10-01

    China's cement industry, which produced 1,388 million metric tons (Mt) of cement in 2008, accounts for almost half of the world's total cement production. Nearly 40% of China's cement production is from relatively obsolete vertical shaft kiln (VSK) cement plants, with the remainder from more modern rotary kiln cement plants, including plants equipped with new suspension pre-heater and pre-calciner (NSP) kilns. Shandong Province is the largest cement-producing Province in China, producing 10% of China's total cement output in 2008. This report documents an analysis of the potential to improve the energy efficiency of NSP kiln cement plants in Shandong Province. Sixteen NSP kiln cement plants were surveyed regarding their cement production, energy consumption, and current adoption of 34 energy-efficient technologies and measures. Plant energy use was compared to both domestic (Chinese) and international best practice using the Benchmarking and Energy Saving Tool for Cement (BEST-Cement). This benchmarking exercise indicated an average technical potential primary energy savings of 12% would be possible if the surveyed plants operated at domestic best practice levels in terms of energy use per ton of cement produced. Average technical potential primary energy savings of 23% would be realized if the plants operated at international best practice levels. Energy conservation supply curves for both fuel and electricity savings were then constructed for the 16 surveyed plants. Using the bottom-up electricity conservation supply curve model, the cost-effective electricity efficiency potential for the studied cement plants in 2008 is estimated to be 373 gigawatt hours (GWh), which accounts for 16% of total electricity use in the 16 surveyed cement plants in 2008. Total technical electricity-saving potential is 915 GWh, which accounts for 40% of total electricity use in the studied plants in 2008. The fuel conservation supply curve model shows the total technical fuel

  12. Corrosion of aluminium metal in OPC- and CAC-based cement matrices

    SciTech Connect (OSTI)

    Kinoshita, Hajime; Swift, Paul; Utton, Claire; Carro-Mateo, Beatriz; Collier, Nick; Milestone, Neil

    2013-08-15

    Corrosion of aluminium metal in ordinary Portland cement (OPC) based pastes produces hydrogen gas and expansive reaction products causing problems for the encapsulation of aluminium containing nuclear wastes. Although corrosion of aluminium in cements has been long known, the extent of aluminium corrosion in the cement matrices and effects of such reaction on the cement phases are not well established. The present study investigates the corrosion reaction of aluminium in OPC, OPC-blast furnace slag (BFS) and calcium aluminate cement (CAC) based systems. The total amount of aluminium able to corrode in an OPC and 4:1 BFS:OPC system was determined, and the correlation between the amount of calcium hydroxide in the system and the reaction of aluminium obtained. It was also shown that a CAC-based system could offer a potential matrix to incorporate aluminium metal with a further reduction of pH by introduction of phosphate, producing a calcium phosphate cement.

  13. Application of resistivity monitoring to evaluate cement grouting effect in earth filled dam

    SciTech Connect (OSTI)

    Kim, Jin-Mo; Yoon, Wang-Jung

    2015-03-10

    In this paper, we applied electrical resistivity monitoring method to evaluate the cement grouting effect. There are a lot of ways to evaluate cement grouting effect. In order to do this evaluation in a great safety, high efficiency, and lower cost, resistivity monitoring is found to be the most appropriate technique. In this paper we have selected a dam site from Korea to acquire resistivity monitoring data and compare the results of inversion to estimate the cement grouting effect.

  14. Ceramic-bonded abrasive grinding tools

    DOE Patents [OSTI]

    Holcombe, Jr., Cressie E.; Gorin, Andrew H.; Seals, Roland D.

    1994-01-01

    Abrasive grains such as boron carbide, silicon carbide, alumina, diamond, cubic boron nitride, and mullite are combined with a cement primarily comprised of zinc oxide and a reactive liquid setting agent and solidified into abrasive grinding tools. Such grinding tools are particularly suitable for grinding and polishing stone, such as marble and granite.

  15. Ceramic-bonded abrasive grinding tools

    DOE Patents [OSTI]

    Holcombe, C.E. Jr.; Gorin, A.H.; Seals, R.D.

    1994-11-22

    Abrasive grains such as boron carbide, silicon carbide, alumina, diamond, cubic boron nitride, and mullite are combined with a cement primarily comprised of zinc oxide and a reactive liquid setting agent and solidified into abrasive grinding tools. Such grinding tools are particularly suitable for grinding and polishing stone, such as marble and granite.

  16. Elastic Moduli of Cemented Sphere Packs (Journal Article) | SciTech...

    Office of Scientific and Technical Information (OSTI)

    Journal Article: Elastic Moduli of Cemented Sphere Packs Citation Details In-Document ... Publication Date: 1999-07-01 OSTI Identifier: 850264 Resource Type: Journal Article ...

  17. DOE Foamed-Cement Research Is Changing Industry | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Foamed-Cement Research Is Changing Industry DOE Foamed-Cement Research Is Changing Industry July 18, 2016 - 11:48am Addthis 3-D renderings (A and B) and scanning electron image of foamed cement. 3-D renderings (A and B) and scanning electron image of foamed cement. The Energy Department's National Energy Technology Laboratory (NETL) is playing a key role in updating a 25-year-old testing standard that helps ensure quality, reduce cost, decrease waste, and support safer oil and gas operations

  18. Qualified Energy Conservation Bonds (QECBs) & New Clean Renewable Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Bonds (New CREBs) | Department of Energy Qualified Energy Conservation Bonds (QECBs) & New Clean Renewable Energy Bonds (New CREBs) Qualified Energy Conservation Bonds (QECBs) & New Clean Renewable Energy Bonds (New CREBs) Provides a presentation overview of qualified energy conservation bond and new clean renewable energy bonds, including characteristics, mechanics, allocated volume, and other information. Author: U.S. Department of Energy Qualified Energy Conservation Bonds &

  19. Assessment of interfacial microstructure and bond properties in aged GRC using a novel microindentation method

    SciTech Connect (OSTI)

    Zhu, W.; Bartos, P.J.M.

    1997-11-01

    Changes of microstructure and properties in the interfacial zone of glass fiber reinforced cement (GRC) under the effect of aging were investigated. A novel technique based on a microindentation apparatus was developed and successfully used to carry out microstrength testing in the interfacial area and push-in tests on selected individual fibers within a strand. By continuously monitoring load vs. displacement, the new technique allowed the microstrength to be measured in small, porous areas of the fiber-matrix interfacial zone, and particularly within the glass fiber strand/bundle. The results showed that the embrittlement of aged GRC was closely associated with a substantial increase of the microstrength values within the fiber bundle during the aging process. It was also revealed that a wide range of bond properties existed within the fiber strand. The resistance to fiber sliding was much greater at the outer filaments than at the inner central filaments of the fiber strand/bundle.

  20. Bell Canyon Test (BCT) cement grout development report

    SciTech Connect (OSTI)

    Gulick, C.W. Jr.; Boa, J.A. Jr.; Buck, A.D.

    1980-12-01

    Development of the cement grout for the Bell Canyon Test was accomplished at the US Army Engineer Waterways Experiment Station (WES), Vicksburg, Mississippi. Initial development work centered on a saltwater grout with Class H cement, fly ash, and an expansive additive. Testing of the saltwater grout showed suitable properties except for the interface between anhydrite rock and grout in small core samples. Higher than expected permeability occurred at the interface because of space between the grout and the anhydrite; the space was produced as a result of allowing the specimens to dry. A change to freshwater grout and proper care to prevent the specimens from drying alleviated this condition. The BCT-1FF freshwater grout mixture was used in both the plug ONE and ONEX field grouting operations. Testing of the development grout mixtures was also done at Dowell, Pennsylvania State University, and Oak Ridge National Laboratory. Results of the testing and evaluation by the four laboratories are included in the report. Field batching, mixing, and placement of the grout at the plug locations for both plug ONE and ONEX were satisfactory with adequate quality control. The freshwater grout mixture maintained adequate flow characteristics for pumpability for 3 1/2 h during each of the two field operations. Physical property and expansivity data for the field samples through 90 days' age are in general agreement with laboratory development data. A large number of samples were obtained for inclusion in the long-term durability studies and the geochemical programs. The high-density, low water-cement ratio expansive grout (BCT-1FF) is considered to be an excellent candidate for plugging boreholes at most locations (except through halite sections).

  1. Covalent Bonding in Actinide Sandwich Molecules

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Covalent Bonding in Actinide Sandwich Molecules Print Glenn Seaborg was one of the first scientists to recognize that differences in the degree of covalent bonding in lanthanide and actinide compounds could have profound consequences for their unique chemical reactivity and physical properties. Now, researchers working at ALS Beamline 11.0.2 have found evidence for unexpected bonding interactions in two organometallic actinide "sandwich" complexes that have been lightning rods in

  2. Covalent Bonding in Actinide Sandwich Molecules

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Covalent Bonding in Actinide Sandwich Molecules Print Glenn Seaborg was one of the first scientists to recognize that differences in the degree of covalent bonding in lanthanide and actinide compounds could have profound consequences for their unique chemical reactivity and physical properties. Now, researchers working at ALS Beamline 11.0.2 have found evidence for unexpected bonding interactions in two organometallic actinide "sandwich" complexes that have been lightning rods in

  3. Covalent Bonding in Actinide Sandwich Molecules

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Covalent Bonding in Actinide Sandwich Molecules Print Glenn Seaborg was one of the first scientists to recognize that differences in the degree of covalent bonding in lanthanide and actinide compounds could have profound consequences for their unique chemical reactivity and physical properties. Now, researchers working at ALS Beamline 11.0.2 have found evidence for unexpected bonding interactions in two organometallic actinide "sandwich" complexes that have been lightning rods in

  4. Covalent Bonding in Actinide Sandwich Molecules

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Covalent Bonding in Actinide Sandwich Molecules Print Glenn Seaborg was one of the first scientists to recognize that differences in the degree of covalent bonding in lanthanide and actinide compounds could have profound consequences for their unique chemical reactivity and physical properties. Now, researchers working at ALS Beamline 11.0.2 have found evidence for unexpected bonding interactions in two organometallic actinide "sandwich" complexes that have been lightning rods in

  5. Covalent Bonding in Actinide Sandwich Molecules

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Covalent Bonding in Actinide Sandwich Molecules Print Glenn Seaborg was one of the first scientists to recognize that differences in the degree of covalent bonding in lanthanide and actinide compounds could have profound consequences for their unique chemical reactivity and physical properties. Now, researchers working at ALS Beamline 11.0.2 have found evidence for unexpected bonding interactions in two organometallic actinide "sandwich" complexes that have been lightning rods in

  6. Covalent Bonding in Actinide Sandwich Molecules

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Covalent Bonding in Actinide Sandwich Molecules Print Glenn Seaborg was one of the first scientists to recognize that differences in the degree of covalent bonding in lanthanide and actinide compounds could have profound consequences for their unique chemical reactivity and physical properties. Now, researchers working at ALS Beamline 11.0.2 have found evidence for unexpected bonding interactions in two organometallic actinide "sandwich" complexes that have been lightning rods in

  7. New subsea wiper plugs hold down deepwater cementing costs

    SciTech Connect (OSTI)

    Stringer, R.; Sonnefeld, A.; Minge, J.

    1997-02-01

    British Petroleum Exploration (BPX) achieved top-quality cementing performance at significantly lower costs in a deepwater area 45 miles offshore Louisiana by using a new method of launching subsea wiper plugs. The method is based on a newly designed subsea casing wiper plug release system, which uses up to three solid wiper plugs loaded in a basket and released by individual darts launched from a surface tool. This design has eliminated the problems sometimes associated with the latching, unlatching and sealing of conventional subsea casing wiper plugs.

  8. TMACS test procedure TP005: Sensor configuration, logging, and data conversion. Revision 4

    SciTech Connect (OSTI)

    Washburn, S.J.

    1994-08-25

    The TMACS Software Project Test Procedures translate the project`s acceptance criteria into test steps. Software releases are certified when the affected Test Procedures are successfully performed and the customers authorize installation of these changes. This Test Procedure addresses the sensor configuration, conversion and logging requirements of the TMACS. The features to be tested are as follows: sensor configuration data; conversion of continuous sensor data to engineering units; conversion of digital data to discrete states; discrete sensor data logging; and continuous sensor data logging.

  9. Covalent Bonding in Actinide Sandwich Molecules

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ALS Beamline 11.0.2 have found evidence for unexpected bonding interactions in two organometallic actinide "sandwich" complexes that have been lightning rods in discussions of...

  10. Metal-bonded graphite foam composites

    SciTech Connect (OSTI)

    Menchhofer, Paul A; Klett, James W

    2015-04-28

    A metal-bonded graphite foam composite includes a ductile metal continuous phase and a dispersed phase that includes graphite foam particles.

  11. Hydrogen Adsorption Induces Interlayer Carbon Bond Formation...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Hydrogen Adsorption Induces Interlayer Carbon Bond Formation in Supported Few-Layer ... that only a sub-monolayer amount of hydrogen adsorption on the topmost layer results ...

  12. Green Infrastructure Bonds | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    allowing the Department of Business, Economic Development, and Tourism to issue Green Infrastructure Bonds to secture low-cost financing for clean energy installations,...

  13. Covalent Bonding in Actinide Sandwich Molecules

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    bonds, are vital as industrial or bioinorganic catalysts and as precursors for nanomaterial synthesis. The work at the ALS also provides conclusive evidence for a new form of...

  14. Tire with outer groove containing bonded tube

    DOE Patents [OSTI]

    Welter, Carolin Anna; Chandra, Dinesh; Benedict, Robert Leon

    2016-02-16

    The invention relates generally to a pneumatic rubber tire which contains an outer, annular, circular groove which contains a flexible tube bonded to the walls of the groove.

  15. Portland cement for SO.sub.2 control in coal-fired power plants

    DOE Patents [OSTI]

    Steinberg, Meyer

    1985-01-01

    There is described a method of removing oxides of sulfur from the emissions of fossil fuel combustion by injecting portland cement into the boiler with the fuel, the combustion air, or downstream with the combustion gases. There is also described the cement products that result from this method.

  16. Portland cement for SO/sub 2/ control in coal-fired power plants

    DOE Patents [OSTI]

    Steinberg, M.

    1984-10-17

    A method is described for removing oxides of sulfur from the emissions of fossil fuel combustion by injecting portland cement into the boiler with the fuel, the combustion air, or downstream with the combustion gases. The cement products that result from this method is also described. 1 tab.

  17. The effect of cure conditions on the stability of cement waste forms after immersion in water

    SciTech Connect (OSTI)

    Siskind, B.; Adams, J.W.; Clinton, J.H.; Piciulo, P.L.; McDaniel, K.

    1988-01-01

    We investigated the effects of curing conditions on the stability of cement-solidified ion-exchange resins after immersion in water. The test specimens consisted of partially depleted mixed-bed bead resins solidified in one of three vendor-supplied Portland I cement formulations, in a reference cement formulation, or in a gypsum-based binder formulation. We cured samples prepared using each formulation in sealed containers for periods of 7, 14, or 28 days as well as in air or with an accelerated heat cure prior to 90-day immersion in water. Two cement formulations exhibited apparent Portland-cement-like behavior, i.e., compressive strength increased or stabilized with increasing cure time. Two cement formulations exhibited behavior apparently unlike that of Portland cement, i.e., compressive strength decreased with increasing cure time. Such non-Portland-cement-like behavior is correlated with higher waste loadings. The gypsum-based formulation exhibited approximately constant compressive strength with cure time. Accelerated heat cures may not give compressive strengths representative of real-time cures. Some physical deterioration (cracking, spalling) of the waste form occurs during immersion.

  18. Study on modification of the high-strength slag cement material

    SciTech Connect (OSTI)

    Wang Fusheng . E-mail: fusheng429@163.com; Sun Ruilian; Cui Yingjing

    2005-07-01

    The influence of the slag powder's fineness, the amounts of activator, type and contents of modification addition on the dry-shrinkage and strength of the high-strength slag cement material was investigated. The experimental data showed that adding 9% Na{sub 2}SiO{sub 3} activator and 10% Portland cement (PC) made the ratios of drying-shrinkage of high-strength slag cement material similar to the ratios of Portland cement and the compressive strengths as higher. The main hydration products are calcium alumina-silicate gels and a little CH; the gel ratio of CaO/SiO{sub 2} is close to 1 and includes a little Na{sub 2}O and MgO for high-strength slag cement material, as shown by means of scanning electron microscope (SEM) and energy-dispersive X-ray analyzer (EDXA)

  19. Apparatus and method for measuring the expansion properties of a cement composition

    DOE Patents [OSTI]

    Spangle, Lloyd B.

    1983-01-01

    An apparatus is disclosed which is useful for measuring the expansion properties of semi-solid materials which expand to a solid phase, upon curing, such as cement compositions. The apparatus includes a sleeve, preferably cylindrical, which has a vertical slit on one side, to allow the sleeve to expand. Mounted on the outside of the sleeve are several sets of pins, consisting of two pins each. The two pins in each set are located on opposite sides of the slit. In the test procedure, the sleeve is filled with wet cement, which is then cured to a solid. As the cement cures it causes the sleeve to expand. The actual expansion of the sleeve represents an expansion factor for the cement. This factor is calculated by measuring the distance across the pins of each set, when the sleeve is empty, and again after the cured cement expands the sleeve.

  20. Property:Building/SPPurchasedEngyNrmlYrMwhYrLogs | Open Energy...

    Open Energy Info (EERE)

    Datasets Community Login | Sign Up Search Property Edit with form History Property:BuildingSPPurchasedEngyNrmlYrMwhYrLogs Jump to: navigation, search This is a property of type...

  1. Lithology and well log study of Campbell E-2 geothermal test...

    Open Energy Info (EERE)

    well log study of Campbell E-2 geothermal test well, Humboldt House geothermal prospect, Pershing County, Nevada Jump to: navigation, search OpenEI Reference LibraryAdd to library...

  2. Temperatures and Natural Gamma-Ray Logs Obtained in 1986 from...

    Open Energy Info (EERE)

    of the formation to absorb injected fluid after the well was completed. Changes in temperature logs run in July and September appear to result from fluid loss to the...

  3. Evaluation of Porous Medium Permeability by Acoustic Logging Finds Geothermal Applications

    SciTech Connect (OSTI)

    Conche, B.; Lebreton, F.; Rojas, J.

    1986-01-21

    In a well, after an acoustic waveform has circulated through the surrounding porous media, the study of its alteration can help in evaluating their permeability. The treatment of the acoustic compressional wave's first three cycles yields a unique parameter called I-c. The recording of this I-c log all along any open hole interval is now possible by respecting some practical rules known by logging companies. Large flows of fluid found in geothermal low-enthalpy operations have provided an opportunity to check the validity of this method. Cumulative I-c derived permeability with depth (''EXAFLO'' log) correlates with the flowmeter log, as examples will show. Some new aspects of the theory underlying the I-c/permeability relationship have been developed and are described here.

  4. Wellbore cement fracture evolution at the cement–basalt caprock interface during geologic carbon sequestration

    SciTech Connect (OSTI)

    Jung, Hun Bok; Kabilan, Senthil; Carson, James P.; Kuprat, Andrew P.; Um, Wooyong; Martin, Paul F.; Dahl, Michael E.; Kafentzis, Tyler A.; Varga, Tamas; Stephens, Sean A.; Arey, Bruce W.; Carroll, KC; Bonneville, Alain; Fernandez, Carlos A.

    2014-08-01

    Composite Portland cement-basalt caprock cores with fractures, as well as neat Portland cement columns, were prepared to understand the geochemical and geomechanical effects on the integrity of wellbores with defects during geologic carbon sequestration. The samples were reacted with CO2-saturated groundwater at 50 ºC and 10 MPa for 3 months under static conditions, while one cement-basalt core was subjected to mechanical stress at 2.7 MPa before the CO2 reaction. Micro-XRD and SEM-EDS data collected along the cement-basalt interface after 3-month reaction with CO2-saturated groundwater indicate that carbonation of cement matrix was extensive with the precipitation of calcite, aragonite, and vaterite, whereas the alteration of basalt caprock was minor. X-ray microtomography (XMT) provided three-dimensional (3-D) visualization of the opening and interconnection of cement fractures due to mechanical stress. Computational fluid dynamics (CFD) modeling further revealed that this stress led to the increase in fluid flow and hence permeability. After the CO2-reaction, XMT images displayed that calcium carbonate precipitation occurred extensively within the fractures in the cement matrix, but only partially along the fracture located at the cement-basalt interface. The 3-D visualization and CFD modeling also showed that the precipitation of calcium carbonate within the cement fractures after the CO2-reaction resulted in the disconnection of cement fractures and permeability decrease. The permeability calculated based on CFD modeling was in agreement with the experimentally determined permeability. This study demonstrates that XMT imaging coupled with CFD modeling represent a powerful tool to visualize and quantify fracture evolution and permeability change in geologic materials and to predict their behavior during geologic carbon sequestration or hydraulic fracturing for shale gas production and enhanced geothermal systems.

  5. Dynamic Evolution of Cement Composition and Transport Properties under Conditions Relevant to Geological Carbon Sequestration

    SciTech Connect (OSTI)

    Brunet, Jean-Patrick Leopold; Li, Li; Karpyn, Zuleima T.; Strazisar, Brian; Bromhal Grant

    2013-08-01

    Assessing the possibility of CO{sub 2} leakage is one of the major challenges for geological carbon sequestration. Injected CO{sub 2} can react with wellbore cement, which can potentially change cement composition and transport properties. In this work, we develop a reactive transport model based on experimental observations to understand and predict the property evolution of cement in direct contact with CO{sub 2}-saturated brine under diffusion-controlled conditions. The model reproduced the observed zones of portlandite depletion and calcite formation. Cement alteration is initially fast and slows down at later times. This work also quantified the role of initial cement properties, in particular the ratio of the initial portlandite content to porosity (defined here as ?), in determining the evolution of cement properties. Portlandite-rich cement with large ? values results in a localized sharp reactive diffusive front characterized by calcite precipitation, leading to significant porosity reduction, which eventually clogs the pore space and prevents further acid penetration. Severe degradation occurs at the cementbrine interface with large ? values. This alteration increases effective permeability by orders of magnitude for fluids that preferentially flow through the degraded zone. The significant porosity decrease in the calcite zone also leads to orders of magnitude decrease in effective permeability, where fluids flow through the low-permeability calcite zone. The developed reactive transport model provides a valuable tool to link cementCO{sub 2} reactions with the evolution of porosity and permeability. It can be used to quantify and predict long-term wellbore cement behavior and can facilitate the risk assessment associated with geological CO{sub 2} sequestration.

  6. Synthesis of belite cement clinker of high hydraulic reactivity

    SciTech Connect (OSTI)

    Kacimi, Larbi Simon-Masseron, Angelique Salem, Souria Ghomari, Abdelhamid Derriche, Zoubir

    2009-07-15

    This study is concerned with the increase of the cooling rate of belite clinker, by using the water quenching for the chemical stabilization of reactive belite, which improves the hydraulic properties of this clinker. The addition of adequate mineralizers, as NaF and Fe{sub 2}O{sub 3}, contributes to the improvement of the clinker properties obtained at low burning temperature. X-ray fluorescence spectroscopy, X-ray diffraction analysis and optical microscopy were used to determine the chemical and mineralogical compositions of this clinker. The samples were analyzed by means of a scanning electronic microscope connected with an energy-dispersive X-ray spectrometer to detect the composition of the belite phase and its morphology. Physical and mechanical properties of this clinker cement were determined. The results show that the belite clinker obtained at 1150 {sup o}C, with lime saturation factor 0.67, is characterized by a great hydraulic reactivity, similar to that of the ordinary alite clinker. The addition of 2% of NaF and the water quenching improved the chemical, mineralogical and structural properties, while improving the cement hydraulic properties.

  7. Leachability of decontamination reagents from cement waste forms

    SciTech Connect (OSTI)

    Piciulo, P.L.; Davis, M.S.; Adams, J.W.

    1984-11-26

    Brookhaven National Laboratory, in order to provide technical information needed by the US Nuclear Regulatory Commission to evaluate the adequacy of near-surface disposal of decontamination wstes, has begun to study the leachability of organic reagents from solidified simulated decontamination wastes. Laboratory-scale cement waste forms containing EDTA, picolinic acid or simulated LOMI decontamination reagent were leach tested. Samples containing an organic reagent on either mixed bed ion-exchange resins or anion exchange resins were tested. A fixed interval leach procedure was used, as well as the standard procedure ANS 16.1. The leachability indices measured for the release of the acid from resin/cement composites are: 10.1 for EDTA on mixed bed resins; 9.1 for picolinic acid on mixed bed resins; 9.2 for picolinic acid on anion exchange resins; 8.8 for picolinic acid in forms containing simulated low oxidation metallic ion (LOMI) reagent on mixed bed resins and 8.7 for picolinic acid in forms containing simulated LOMI reagent on anion exchange resins. The leachability indices measured varied with leach time and the data indicate that the release mechanism may not be simply diffusion controlled. 5 references, 2 tables.

  8. Hydration studies of calcium sulfoaluminate cements blended with fly ash

    SciTech Connect (OSTI)

    Garca-Mat, M.; De la Torre, A.G.; Len-Reina, L.; Aranda, M.A.G.; CELLS-Alba synchrotron, Carretera BP 1413, Km. 3.3, E-08290 Cerdanyola, Barcelona ; Santacruz, I.

    2013-12-15

    The main objective of this work is to study the hydration and properties of calcium sulfoaluminate cement pastes blended with fly ash (FA) and the corresponding mortars at different hydration ages. Laboratory X-ray powder diffraction, rheological studies, thermal analysis, porosimetry and compressive strength measurements were performed. The analysis of the diffraction data by Rietveld method allowed quantifying crystalline phases and overall amorphous contents. The studied parameters were: i) FA content, 0, 15 and 30 wt.%; and ii) water addition, water-to-CSA mass ratio (w/CSA = 0.50 and 0.65), and water-to-binder mass ratio (w/b = 0.50). Finally, compressive strengths after 6 months of 0 and 15 wt.% FA [w/CSA = 0.50] mortars were similar: 73 2 and 72 3 MPa, respectively. This is justified by the filler effect of the FA as no strong evidences of reactivity of FA with CSA were observed. These results support the partial substitution of CSA cements with FA with the economic and environmental benefits.

  9. Evaluation of cement kiln laboratories testing hazardous waste derived fuels

    SciTech Connect (OSTI)

    Nichols, R.E.

    1998-12-31

    Cement kiln operators wishing to burn hazardous waste derived fuels in their kilns must submit applications for Resource Conservation Recovery Act permits. One component of each permit application is a site-specific Waste Analysis Plan. These Plans describe the facilities` sampling and analysis procedures for hazardous waste derived fuels prior to receipt and burn. The Environmental Protection Agency has conducted on-site evaluations of several cement kiln facilities that were under consideration for Resource Conservation Recovery Act permits. The purpose of these evaluations was to determine if the on-site sampling and laboratory operations at each facility complied with their site-specific Waste Analysis Plans. These evaluations covered sampling, laboratory, and recordkeeping procedures. Although all the evaluated facilities were generally competent, the results of those evaluations revealed opportunities for improvement at each facility. Many findings were noted for more than one facility. This paper will discuss these findings, particularly those shared by several facilities (specific facilities will not be identified). Among the findings to be discussed are the ways that oxygen bombs were scrubbed and rinsed, the analytical quality control used, Burn Tank sampling, and the analysis of pH in hazardous waste derived fuels.

  10. SOLID STATE BONDING OF THORIUM WITH ALUMINUM

    DOE Patents [OSTI]

    Storchhelm, S.

    1959-12-01

    A method is described for bonding thorium and aluminum by placing clean surfaces of thorium and aluminum in contact with each other and hot pressing the metals together in a protective atmosphere at a temperature of about 375 to 575 deg C and at a pressure of at least 10 tsi to effect a bond.

  11. Identification of products containing {single_bond}COOH, {single_bond}OH, and {single_bond}C{double_bond}O in atmospheric oxidation of hydrocarbons

    SciTech Connect (OSTI)

    Yu, J.; Flagan, R.C.; Seinfeld, J.H.

    1998-08-15

    Atmospheric oxidation of hydrocarbons by hydroxyl radicals and ozone leads to products containing {single_bond}COOH, {single_bond}OH, and {single_bond}C{double_bond}O functional groups. The high polarity of such compounds precludes direct GC-MS analysis. In addition, many such compounds often exist in a single sample at trace levels. An analytical method has been developed to identify compounds containing one or more functional groups of carbonyl, carboxy, and hydroxy in atmospheric samples. In the method, {single_bond}C{double_bond}O groups are derivatized using O-(2,3,4,5,6-pentafluorobenzyl) hydroxy amine(PFBHA), and {single_bond}COOH and {single_bond}OH groups are derivatized using a silylation reagent N,O-bis(trimethylsilyl)-trifluoroacetamide (BSTFA). The derivatives are easily resolved by a GC column. The chemical ionization mass spectra of these derivatives exhibit several pseudomolecular ions, allowing unambiguous determination of molecular weights. Functional group identification is accomplished by monitoring the ions in the electron ionization mass spectra that are characteristic of each functional group derivative: m/z 181 for carbonyl and m/z 73 and 75 for carboxyl and hydroxy groups. The method is used to identify products in laboratory studies of ozone oxidation of {alpha}-pinene and {Delta}{sup 3}-carene.

  12. Hydrogen bond dynamics in bulk alcohols

    SciTech Connect (OSTI)

    Shinokita, Keisuke; Cunha, Ana V.; Jansen, Thomas L. C.; Pshenichnikov, Maxim S.

    2015-06-07

    Hydrogen-bonded liquids play a significant role in numerous chemical and biological phenomena. In the past decade, impressive developments in multidimensional vibrational spectroscopy and combined molecular dynamicsquantum mechanical simulation have established many intriguing features of hydrogen bond dynamics in one of the fundamental solvents in nature, water. The next class of a hydrogen-bonded liquidalcoholshas attracted much less attention. This is surprising given such important differences between water and alcohols as the imbalance between the number of hydrogen bonds, each molecule can accept (two) and donate (one) and the very presence of the hydrophobic group in alcohols. Here, we use polarization-resolved pump-probe and 2D infrared spectroscopy supported by extensive theoretical modeling to investigate hydrogen bond dynamics in methanol, ethanol, and isopropanol employing the OH stretching mode as a reporter. The sub-ps dynamics in alcohols are similar to those in water as they are determined by similar librational and hydrogen-bond stretch motions. However, lower density of hydrogen bond acceptors and donors in alcohols leads to the appearance of slow diffusion-controlled hydrogen bond exchange dynamics, which are essentially absent in water. We anticipate that the findings herein would have a potential impact on fundamental chemistry and biology as many processes in nature involve the interplay of hydrophobic and hydrophilic groups.

  13. 1 mil gold bond wire study.

    SciTech Connect (OSTI)

    Huff, Johnathon; McLean, Michael B.; Jenkins, Mark W.; Rutherford, Brian Milne

    2013-05-01

    In microcircuit fabrication, the diameter and length of a bond wire have been shown to both affect the current versus fusing time ratio of a bond wire as well as the gap length of the fused wire. This study investigated the impact of current level on the time-to-open and gap length of 1 mil by 60 mil gold bond wires. During the experiments, constant current was provided for a control set of bond wires for 250ms, 410ms and until the wire fused; non-destructively pull-tested wires for 250ms; and notched wires. The key findings were that as the current increases, the gap length increases and 73% of the bond wires will fuse at 1.8A, and 100% of the wires fuse at 1.9A within 60ms. Due to the limited scope of experiments and limited data analyzed, further investigation is encouraged to confirm these observations.

  14. Atomically Bonded Transparent Superhydrophobic Coatings

    SciTech Connect (OSTI)

    Aytug, Tolga

    2015-08-01

    Maintaining clarity and avoiding the accumulation of water and dirt on optically transparent surfaces such as US military vehicle windshields, viewports, periscope optical head windows, and electronic equipment cover glasses are critical to providing a high level of visibility, improved survivability, and much-needed safety for warfighters in the field. Through a combination of physical vapor deposition techniques and the exploitation of metastable phase separation in low-alkali borosilicate, a novel technology was developed for the fabrication of optically transparent, porous nanostructured silica thin film coatings that are strongly bonded to glass platforms. The nanotextured films, initially structurally superhydrophilic, exhibit superior superhydrophobicity, hence antisoiling ability, following a simple but robust modification in surface chemistry. The surfaces yield water droplet contact angles as high as 172°. Moreover, the nanostructured nature of these coatings provides increased light scattering in the UV regime and reduced reflectivity (i.e., enhanced transmission) over a broad range of the visible spectrum. In addition to these functionalities, the coatings exhibit superior mechanical resistance to abrasion and are thermally stable to temperatures approaching 500°C. The overall process technology relies on industry standard equipment and inherently scalable manufacturing processes and demands only nontoxic, naturally abundant, and inexpensive base materials. Such coatings, applied to the optical components of current and future combat equipment and military vehicles will provide a significant strategic advantage for warfighters. The inherent self-cleaning properties of such superhydrophobic coatings will also mitigate biofouling of optical windows exposed to high-humidity conditions and can help decrease repair/replacement costs, reduce maintenance, and increase readiness by limiting equipment downtime.

  15. Boosting investor yields through bond insurance

    SciTech Connect (OSTI)

    Mosbacher, M.L.; Burkhardt, D.A.

    1993-02-01

    The market for utility securities generally tends to be fairly static. Innovative financing techniques are rarely used because of the marketability of utility securities stemming from the companies' generally strong financial credit and the monopoly markets most utilities serve. To many people, utility securities are considered the pillars of the financial world, and innovation is not needed. Further, plain vanilla utility issues are easily understood by investors, as well as by regulators and customers. Over the past several years, however, a new utility bond product has crept into the world of utility securities - insured secondary utility bonds. These insured bonds may possibly be used as an alternative financing technique for newly issued debt. Individual investors often tend to rely on insurance as a tool for reducing credit risk and are willing to take the lower yields as a tradeoff. Insured utility bonds are created by brokerage firms through the acqusition of a portion of an outstanding utility bond issue and subsequent solicitation of the insurance companies for bids. The insurance company then agrees to insure that portion of the issue until maturity for a fee, and the brokerage firm sells those bonds to their customers as a AAA-insured bond. Issuers are encouraged to explore the retail market as a financing alternative. They may find a most cost-effective means of raising capital.

  16. Carbon dioxide capture from a cement manufacturing process

    DOE Patents [OSTI]

    Blount, Gerald C.; Falta, Ronald W.; Siddall, Alvin A.

    2011-07-12

    A process of manufacturing cement clinker is provided in which a clean supply of CO.sub.2 gas may be captured. The process also involves using an open loop conversion of CaO/MgO from a calciner to capture CO.sub.2 from combustion flue gases thereby forming CaCO.sub.3/CaMg(CO.sub.3).sub.2. The CaCO.sub.3/CaMg(CO.sub.3).sub.2 is then returned to the calciner where CO.sub.2 gas is evolved. The evolved CO.sub.2 gas, along with other evolved CO.sub.2 gases from the calciner are removed from the calciner. The reactants (CaO/MgO) are feed to a high temperature calciner for control of the clinker production composition.

  17. Improved method and composition for immobilization of waste in cement-based material

    DOE Patents [OSTI]

    Tallent, O.K.; Dodson, K.E.; McDaniel, E.W.

    1987-10-01

    A composition and method for fixation or immobilization of aqueous hazardous waste material in cement-based materials (grout) is disclosed. The amount of drainable water in the cured grout is reduced by the addition of an ionic aluminum compound to either the waste material or the mixture of waste material and dry-solid cement- based material. This reduction in drainable water in the cured grout obviates the need for large, expensive amounts of gelling clays in grout materials and also results in improved consistency and properties of these cement-based waste disposal materials.

  18. Surface preparation of adhesively bonded joints

    SciTech Connect (OSTI)

    Hogg, I.C.; Janardhana, M.N.

    1993-12-31

    For the bonding of structures, it is essential that correct surface preparation is completed to ensure both a reliable and a durable bond. In a controlled environment this can be achieved easily, but difficulties can occur in the field. This paper is a compilation of research completed in the area of surface preparation for the bonding of aluminum and graphite epoxy composites. Finite element analysis software MSC/NASTRAN has been used to investigate the effect of adhesion on the strength and failure characteristics of a single lap joint.

  19. Process Of Bonding Copper And Tungsten

    DOE Patents [OSTI]

    Slattery, Kevin T.; Driemeyer, Daniel E.; Davis, John W.

    2000-07-18

    Process for bonding a copper substrate to a tungsten substrate by providing a thin metallic adhesion promoting film bonded to a tungsten substrate and a functionally graded material (FGM) interlayer bonding the thin metallic adhesion promoting film to the copper substrate. The FGM interlayer is formed by sintering a stack of individual copper and tungsten powder blend layers having progressively higher copper content/tungsten content, by volume, ratio values in successive powder blend layers in a lineal direction extending from the tungsten substrate towards the copper substrate. The resulting copper to tungsten joint well accommodates the difference in the coefficient of thermal expansion of the materials.

  20. Testing of thermally enhanced cement ground heat exchanger grouts

    SciTech Connect (OSTI)

    Kavanaugh, S.P.; Allan, M.L.

    1999-07-01

    Optimal performance of closed-loop, ground-source heat pumps (ground-coupled heat pumps) is dependent upon the thermal properties of the backfill in the annual region between the ground heat exchanger (GHEX) tubes and the outer bore wall. Equally important is the protection of groundwater aquifers from contaminants that may flow from the surface of other aquifers through poorly sealed boreholes. Conventional cement and bentonite-based grouts have relatively low thermal conductivities. Loop requirements often increase beyond the allotted budget in applications where regulatory bodies require the entire heat exchanger length to be grouted. This paper reports on the results of four mixes of thermally enhanced cementitious grouts. Four grouts were evaluated in a test stand to minimize the impact of external factors typically present in field tests. The test stand accepts up to 6 in. (15 cm) ground heat exchangers in a 10 ft (3 m) test section. Controlled testing is performed in either the cooling mode (loop above 85 F [29 C]) or heating mode (loop at 32 F [0 C]), and the temperature of the outer bore wall is held constant with a groundwater source. Results indicate cement grouts that are enhanced with low-cost additives have thermal conductivities three to four times as large as conventional high-solids bentonite grouts. This would result in reduced heat exchanger lengths compared to those grouted with bentonite. There appears to be no measurable increase in overall borehole resistance due to separation of the colder tubes from the grout in the heating mode. This discussion does not include pumpability, permeability, and material handling issues, which must be thoroughly investigated before any grout can be recommended for use.

  1. A Surprising Path for Proton Transfer Without Hydrogen Bonds

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    A Surprising Path for Proton Transfer Without Hydrogen Bonds Print Hydrogen bonds are found everywhere in chemistry and biology and are critical in DNA and RNA. A hydrogen bond...

  2. A Surprising Path for Proton Transfer Without Hydrogen Bonds

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    A Surprising Path for Proton Transfer Without Hydrogen Bonds A Surprising Path for Proton Transfer Without Hydrogen Bonds Print Wednesday, 25 July 2012 00:00 Hydrogen bonds are...

  3. Evaluation of Simple Causal Message Logging for Large-Scale Fault Tolerant HPC Systems

    SciTech Connect (OSTI)

    Bronevetsky, G; Meneses, E; Kale, L V

    2011-02-25

    The era of petascale computing brought machines with hundreds of thousands of processors. The next generation of exascale supercomputers will make available clusters with millions of processors. In those machines, mean time between failures will range from a few minutes to few tens of minutes, making the crash of a processor the common case, instead of a rarity. Parallel applications running on those large machines will need to simultaneously survive crashes and maintain high productivity. To achieve that, fault tolerance techniques will have to go beyond checkpoint/restart, which requires all processors to roll back in case of a failure. Incorporating some form of message logging will provide a framework where only a subset of processors are rolled back after a crash. In this paper, we discuss why a simple causal message logging protocol seems a promising alternative to provide fault tolerance in large supercomputers. As opposed to pessimistic message logging, it has low latency overhead, especially in collective communication operations. Besides, it saves messages when more than one thread is running per processor. Finally, we demonstrate that a simple causal message logging protocol has a faster recovery and a low performance penalty when compared to checkpoint/restart. Running NAS Parallel Benchmarks (CG, MG and BT) on 1024 processors, simple causal message logging has a latency overhead below 5%.

  4. Clean Energy and Bond Finance Initiative | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Clean Energy and Bond Finance Initiative Clean Energy and Bond Finance Initiative Provides information on Clean Energy and Bond Finance Initiative (CE+BFI). CE+BFI brings together public infrastructure finance agencies, clean energy public fund managers and institutional investors across the country to explore how to raise capital at scale for clean energy development through bond financing. Author: Clean Energy and Bond Finance Initiative Clean Energy and Bond Finance Initiative Website More

  5. Method for forming or bonding a liner

    DOE Patents [OSTI]

    Prevender, Thomas S.

    1980-01-01

    A process and means for forming or bonding a liner to a shell or element wherein the liner is filled with or immersed in water and a portion of the water is frozen.

  6. Local Option- Energy Efficiency Project Bonds

    Broader source: Energy.gov [DOE]

    On March 2015, the Arkansas legislature passed SB 896 or the “Local Government Energy Efficiency Project Bond Act” which provides enabling legislation for a municipality or a county to issue energy...

  7. Producing microchannels using graduated diffusion bonding of...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of precision machined foils or sheets (laminates) to make a micro-channel reactor A novel multi-step process for the diffusion bonding of laminates National Energy Technology...

  8. Opportunities in Bond Financing | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    in Bond Financing Opportunities in Bond Financing Presentation about financial options and opportunities for biogas and fuel cells. Presented by James Dack, Stern Brothers, at the NREL/DOE Biogas and Fuel Cells Workshop held June 11-13, 2012, in Golden, Colorado. june2012_biogas_workshop_dack.pdf (154.9 KB) More Documents & Publications Leveraging Federal Funds Biogas and Fuel Cells Workshop Summary Report: Proceedings from the Biogas and Fuel Cells Workshop, Golden, Colorado, June 11-13,

  9. Method of bonding metals to ceramics

    DOE Patents [OSTI]

    Maroni, Victor A.

    1991-01-01

    A ceramic or glass having a thin layer of silver, gold or alloys thereof at the surface thereof. A first metal is bonded to the thin layer and a second metal is bonded to the first metal. The first metal is selected from the class consisting of In, Ga, Sn, Bi, Zn, Cd, Pb, Tl and alloys thereof, and the second metal is selected from the class consisting of Cu, Al, Pb, An and alloys thereof.

  10. Syntactic foam composites and bonding. Final report

    SciTech Connect (OSTI)

    McWhirter, R.J.

    1980-09-01

    A manufacturing process has been developed to produce billets molded from a composite of carbon microspheres, a polyimide resin, and carbon fibers. The billets then are machined to configuration which results in extremely sharp and fragile edges on one part. To strengthen these parts, a parylene coating is applied, after which the parts are assembled with other parts by bonding. Bonding and assembly problems are discussed in detail; other problems encountered are summarized, and several are referenced to previous reports.

  11. Method of bonding metals to ceramics

    DOE Patents [OSTI]

    Maroni, V.A.

    1991-04-23

    A ceramic or glass having a thin layer of silver, gold or alloys thereof at the surface thereof is disclosed. A first metal is bonded to the thin layer and a second metal is bonded to the first metal. The first metal is selected from the class consisting of In, Ga, Sn, Bi, Zn, Cd, Pb, Tl and alloys thereof, and the second metal is selected from the class consisting of Cu, Al, Pb, Au and alloys thereof. 3 figures.

  12. FITCH RATES ENERGY NORTHWEST, WA'S ELECTRIC REV RFDG BONDS 'AA...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    debt (4.1 billion). KEY RATING DRIVERS BONNEVILLE'S OBLIGATION SECURES BONDS: The rating on the Energy Northwest bonds reflects the credit quality of Bonneville and its...

  13. Qualified Energy Conservation Bonds (QECBs) & New Clean Renewable...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Provides a presentation overview of qualified energy conservation bond and new clean renewable energy bonds, including characteristics, mechanics, allocated volume, and other ...

  14. An unusual carbon-carbon bond cleavage reaction during phosphinothrici...

    Office of Scientific and Technical Information (OSTI)

    An unusual carbon-carbon bond cleavage reaction during phosphinothricin biosynthesis Citation Details In-Document Search Title: An unusual carbon-carbon bond cleavage reaction ...

  15. Photochemical route to actinide-transition metal bonds: synthesis...

    Office of Scientific and Technical Information (OSTI)

    bonds: synthesis, characterization and reactivity of a series of thorium and uranium ... bonds: synthesis, characterization and reactivity of a series of thorium and uranium ...

  16. Fitzgerald Wtr Lgt & Bond Comm | Open Energy Information

    Open Energy Info (EERE)

    Fitzgerald Wtr Lgt & Bond Comm Jump to: navigation, search Name: Fitzgerald Wtr Lgt & Bond Comm Place: Georgia Phone Number: (229) 426-5400 Website: fitzutilities.com Outage...

  17. Intramolecular hydrogen bonding as a synthetic tool to induce...

    Office of Scientific and Technical Information (OSTI)

    hydrogen bonding as a synthetic tool to induce chemical selectivity in acid catalyzed porphyrin synthesis Citation Details In-Document Search Title: Intramolecular hydrogen bonding ...

  18. Taking Advantage of Qualified Energy Conservation Bonds (QECBs...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Advantage of Qualified Energy Conservation Bonds (QECBs) Taking Advantage of Qualified Energy Conservation Bonds (QECBs) This webinar, held on Sept. 22, 2010, provides information ...

  19. Peer Exchange Call on Financing and Revenue: Bond Funding | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Peer Exchange Call on Financing and Revenue: Bond Funding Peer Exchange Call on Financing and Revenue: Bond Funding Better Buildings Neighborhood Program Peer Exchange Call on ...

  20. Fort Bliss Geothermal Area Data: Temperature profile, logs, schematic model and cross section

    SciTech Connect (OSTI)

    Adam Brandt

    2015-11-15

    This dataset contains a variety of data about the Fort Bliss geothermal area, part of the southern portion of the Tularosa Basin, New Mexico. The dataset contains schematic models for the McGregor Geothermal System, a shallow temperature survey of the Fort Bliss geothermal area. The dataset also contains Century OH logs, a full temperature profile, and complete logs from well RMI 56-5, including resistivity and porosity data, drill logs with drill rate, depth, lithology, mineralogy, fractures, temperature, pit total, gases, and descriptions among other measurements as well as CDL, CNL, DIL, GR Caliper and Temperature files. A shallow (2 meter depth) temperature survey of the Fort Bliss geothermal area with 63 data points is also included. Two cross sections through the Fort Bliss area, also included, show well position and depth. The surface map included shows faults and well spatial distribution. Inferred and observed fault distributions from gravity surveys around the Fort Bliss geothermal area.

  1. Calibration models for measuring moisture in unsaturated formations by neutron logging

    SciTech Connect (OSTI)

    Engelman, R.E.; Lewis, R.E.; Stromswold, D.C.

    1995-10-01

    Calibration models containing known amounts of hydrogen have been constructed to simulate unsaturated earth formations for calibrating neutron well logging tools. The models are made of dry mixtures of hydrated alumina (Al(OH){sub 3}) with either silica sand (SiO{sub 2}) or aluminum oxide (Al{sub 2}O{sub 3}). Hydrogen in the hydrated alumina replaces the hydrogen in water for neutron scattering, making it possible to simulate partially saturated formations. The equivalent water contents for the models are 5%, 12%, 20%, and 40% by volume in seven tanks that have a diameter of 1.5 m and a height of 1.8 m. Steel casings of inside diameter 15.4 cm (for three models) and diameter 20.3 cm (for four models) allow logging tool access to simulate logging through cased boreholes.

  2. Experimental study of potential wellbore cement carbonation by various phases of carbon dioxide during geologic carbon sequestration

    SciTech Connect (OSTI)

    Jung, Hun Bok; Um, Wooyong

    2013-08-16

    Hydrated Portland cement was reacted with carbon dioxide (CO2) in supercritical, gaseous, and aqueous phases to understand the potential cement alteration processes along the length of a wellbore, extending from deep CO2 storage reservoir to the shallow subsurface during geologic carbon sequestration. The 3-D X-ray microtomography (XMT) images displayed that the cement alteration was significantly more extensive by CO2-saturated synthetic groundwater than dry or wet supercritical CO2 at high P (10 MPa)-T (50C) conditions. Scanning electron microscopy with energy dispersive spectroscopy (SEM-EDS) analysis also exhibited a systematic Ca depletion and C enrichment in cement matrix exposed to CO2-saturated groundwater. Integrated XMT, XRD, and SEM-EDS analyses identified the formation of extensive carbonated zone filled with CaCO3(s), as well as the porous degradation front and the outermost silica-rich zone in cement after exposure to CO2-saturated groundwater. The cement alteration by CO2-saturated groundwater for 2-8 months overall decreased the porosity from 31% to 22% and the permeability by an order of magnitude. Cement alteration by dry or wet supercritical CO2 was slow and minor compared to CO2-saturated groundwater. A thin single carbonation zone was formed in cement after exposure to wet supercritical CO2 for 8 months or dry supercritical CO2 for 15 months. Extensive calcite coating was formed on the outside surface of a cement sample after exposure to wet gaseous CO2 for 1-3 months. The chemical-physical characterization of hydrated Portland cement after exposure to various phases of carbon dioxide indicates that the extent of cement carbonation can be significantly heterogeneous depending on CO2 phase present in the wellbore environment. Both experimental and geochemical modeling results suggest that wellbore cement exposure to supercritical, gaseous, and aqueous phases of CO2 during geologic carbon sequestration is unlikely to damage the wellbore

  3. Determination of Diffusion Profiles in Altered Wellbore Cement Using X-ray Computed Tomography Methods

    SciTech Connect (OSTI)

    Mason, Harris E.; Walsh, Stuart D. C.; DuFrane, Wyatt L.; Carroll, Susan A.

    2014-06-17

    The development of accurate, predictive models for use in determining wellbore integrity requires detailed information about the chemical and mechanical changes occurring in hardened Portland cements. X-ray computed tomography (XRCT) provides a method that can nondestructively probe these changes in three dimensions. Here, we describe a method for extracting subvoxel mineralogical and chemical information from synchrotron XRCT images by combining advanced image segmentation with geochemical models of cement alteration. The method relies on determining effective linear activity coefficients (ELAC) for the white light source to generate calibration curves that relate the image grayscales to material composition. The resulting data set supports the modeling of cement alteration by CO2-rich brine with discrete increases in calcium concentration at reaction boundaries. The results of these XRCT analyses can be used to further improve coupled geochemical and mechanical models of cement alteration in the wellbore environment.

  4. The role of calcium ions and lignosulphonate plasticiser in the hydration of cement

    SciTech Connect (OSTI)

    Grierson, L.H.; Knight, J.C.; Maharaj, R

    2005-04-01

    Experiments involving equilibrium dialysis, conductivity, X-ray diffraction analysis (XRD), differential thermal analysis (DTA) and isothermal titration calorimetry (ITC) have been carried out to investigate the role of calcium ions and polymeric plasticisers in cement/admixture hydration. Results from a study of lignosulphonic acid, sodium salt, acetate as a plasticiser shows that a plasticiser has dual role; one mainly as a kinetic inhibitor (poison) in cement hydration mechanism and the other as a dispersant. Evidence of a weak Ca{sup 2+} binding to lignosulphonate sulphonic moieties was found at low ionic strengths of 0.1 M using ITC. No evidence of formal Ca{sup 2+} binding to lignosulphonate sulphonic acid moieties was found using equilibrium dialysis at higher ionic strength of 1 M (ionic strengths of 0.4 M are typically found in Portland cement pore solution), as is often suggested in cement/admixture literature.

  5. Trends in characteristics of hazardous waste-derived fuel burned for energy recovery in cement kilns

    SciTech Connect (OSTI)

    Lusk, M.G.; Campbell, C.S.

    1996-12-31

    The Cement Kiln Recycling Coalition (CKRC) is a national trade association representing virtually all the U.S. cement companies involved in the use of waste-derived fuel in the cement manufacturing process as well as those companies involved in the collection, processing, managing, and marketing of such fuel. CKRC, in conjunction with the National Association of Chemical Recyclers (NACR), completed several data collection activities over the past two years to provide the Environmental Protection Agency (EPA) and other interested parties with industry-wide trend analyses. The analyses evaluated the content of specific metals in waste fuels utilized by cement kilns, average Btu value of substitute fuels used by kilns, and provides insight into the trends of these properties. With the exception of the data collected by NACR, the study did not evaluate materials sent to hazardous waste incinerators or materials that are combusted at {open_quotes}on-site{close_quotes} facilities.

  6. Fan System Optimization Improves Production and Saves Energy at Ash Grove Cement Plant

    SciTech Connect (OSTI)

    2002-05-01

    This case study describes an optimization project implemented on a fan system at Ash Grove Cement Company, which led to annual energy and maintenance savings of $16,000 and 175,000 kilowatt-hours (kWh).

  7. New technologies address the problem areas of coiled-tubing cementing

    SciTech Connect (OSTI)

    Carpenter, R.B. )

    1992-05-01

    Coiled-tubing cementing has been practiced successfully on the Alaskan North Slope for several years. This paper discusses the special problems faced when this technology was applied to offshore U.S. gulf coast operations. The innovative solutions and procedures developed to improve the economic and technical success of coiled-tubing cementing are also discussed. Comparative laboratory and computer studies, as well as field case histories, will be presented to show the economic merit of this technology.

  8. Improved coiled-tubing squeeze-cementing techniques at Prudhoe Bay

    SciTech Connect (OSTI)

    Hornbrook, P.R.; Mason, C.M. )

    1991-04-01

    This paper presents major changes in coiled-tubing squeeze-cementing techniques used in the Prudhoe Bay Unit Western Operating Area (PBUWOA). Changes include introduction of a polymer diluent to replace borax contamination, increased differential pressures placed on squeeze and coil, reduced cement volumes, and incorporation of an inflow test and resqueeze procedure. These changes resulted in increased squeeze effectiveness by reducing equipment and engineering time requirements and by shortening well shut-in time after the workover.

  9. The use of Devonian oil shales in the production of portland cement

    SciTech Connect (OSTI)

    Schultz, C.W.; Lamont, W.E.; Daniel, J.

    1991-12-31

    The Lafarge Corporation operates a cement plant at Alpena, Michigan in which Antrim shale, a Devonian oil shale, is used as part of the raw material mix. Using this precedent the authors examine the conditions and extent to which spent shale might be utilized in cement production. They conclude that the potential is limited in size and location but could provide substantial benefit to an oil shale operation meeting these criteria.

  10. The use of Devonian oil shales in the production of portland cement

    SciTech Connect (OSTI)

    Schultz, C.W.; Lamont, W.E. ); Daniel, J. )

    1991-01-01

    The Lafarge Corporation operates a cement plant at Alpena, Michigan in which Antrim shale, a Devonian oil shale, is used as part of the raw material mix. Using this precedent the authors examine the conditions and extent to which spent shale might be utilized in cement production. They conclude that the potential is limited in size and location but could provide substantial benefit to an oil shale operation meeting these criteria.

  11. Secure optionally passive RFID tag or sensor with external power source and data logging

    DOE Patents [OSTI]

    Nekoogar, Faranak; Reynolds, Matthew; Lefton, Scott; Dowla, Farid; Twogood, Richard

    2016-05-31

    A secure optionally passive RFID tag or sensor system comprises a passive RFID tag having means for receiving radio signals from at least one base station and for transmitting radio signals to at least one base station, where the tag is capable of being powered exclusively by received radio energy, and an external power and data logging device having at least one battery and electronic circuitry including a digital memory configured for storing and recalling data. The external power and data logging device has a means for powering the tag, and also has a means.

  12. Borehole induction logging for the Dynamic Underground Stripping Project LLNL gasoline spill site

    SciTech Connect (OSTI)

    Boyd, S.; Newmark, R.; Wilt, M.

    1994-01-21

    Borehole induction logs were acquired for the purpose of characterizing subsurface physical properties and monitoring steam clean up activities at the Lawrence Livermore National Laboratory. This work was part of the Dynamic Underground Stripping Project`s demonstrated clean up of a gasoline spin. The site is composed of unconsolidated days, sands and gravels which contain gasoline both above and below the water table. Induction logs were used to characterize lithology, to provide ``ground truth`` resistivity values for electrical resistance tomography (ERT), and to monitor the movement of an underground steam plume used to heat the soil and drive volatile organic compounds (VOCs) to the extraction wells.

  13. Guidance for Energy Efficiency and Conservation Block Grant Grantees on Qualified Energy Conservation Bonds and New Clean Renewable Energy Bonds

    Broader source: Energy.gov [DOE]

    Guidance for Energy Efficiency and Conservation Block Grant Program grantees regarding Qualified Energy Conservation Bonds (QECBs) and New Clean Renewable Energy Bonds (New CREBs)

  14. New high temperature cementing materials for geothermal wells: stability and properties. Final report

    SciTech Connect (OSTI)

    Roy, D.M.; White, E.L.; Langton, C.A.; Grutzeck, M.W.

    1980-07-01

    Potential high-temperature cements have been formulated and evaluated in terms of their properties for geothermal well cementing. Phase formation and compatibility in two major compositional regions were investigated in the temperature region between 200 and 400/sup 0/C and pressures up to 69 MPa (10,000 psi). These were followed by an evaluation of properties of the cements formed. One area in the system Ca0-Mg0-Si0/sub 2/-H/sub 2/0 centered around the xonotlite-chrysotile join while the other area of interest centered around the anorthite composition in the system Ca0-Al/sub 2/O/sub 3/-SiO/sub 2/-H/sub 2/O. After numerous exploratory studies, the magnesia-containing mixtures were prepared by mixing a Class J cement with various sources of magnesia such as calcined chrysotile, or magnesium oxide. Calcium oxide and silica fine quartz powder were also added to adjust the compositions. The aluminous system cements were formulated from high-alumina cements which were mixed with various silica sources.

  15. Percutaneous Extraction of Cement Leakage After Vertebroplasty Under CT and Fluoroscopy Guidance: A New Technique

    SciTech Connect (OSTI)

    Amoretti, Nicolas Huwart, Laurent

    2012-12-15

    Purpose: We report a new minimally invasive technique of extraction of cement leakage following percutaneous vertebroplasty in adults. Methods: Seven adult patients (five women, two men; mean age: 81 years) treated for vertebral compression fractures by percutaneous vertebroplasty had cement leakage into perivertebral soft tissues along the needle route. Immediately after vertebroplasty, the procedure of extraction was performed under computed tomography (CT) and fluoroscopy guidance: a Chiba needle was first inserted using the same route as the vertebroplasty until contact was obtained with the cement fragment. This needle was then used as a guide for an 11-gauge Trocar t'am (Thiebaud, France). After needle withdrawal, a 13-gauge endoscopy clamp was inserted through the cannula to extract the cement fragments. The whole procedure was performed under local anesthesia. Results: In each patient, all cement fragments were withdrawn within 10 min, without complication. Conclusions: This report suggests that this CT- and fluoroscopy-guided percutaneous technique of extraction could reduce the rate of cement leakage-related complications.

  16. Literature survey on cements for remediation of deformed casing in geothermal wells

    SciTech Connect (OSTI)

    Allan, M.L.; Philippacopoulos, A.J.

    1998-12-31

    Brookhaven National Laboratory was requested to conduct a literature survey for the best available cement to use in the proposed casing patch as part of the Geothermal Drilling Organization (GDO) project on remediation of deformed casings. A total of 50 wells have been identified with deformed production casing in Unocal`s portion of The Geysers geothermal field. A procedure to address the casing deformation and avoid abandonment of these wells has been developed as described in the Geysers Deformed Casing Remediation Proposal. The proposed remediation procedure involves isolation of the zone of interest with an inflatable packer, milling the deformed casing and cementing a 7 inch diameter liner to extend approximately 100 ft above and 100 ft below the milled zone. During the milling operation it is possible that the original cement and surrounding formation may slough away. In order to specify a suitable cement formulation for the casing patch it is first necessary to identify and understand the deformation mechanism/s operating in The Geysers field. Subsequently, the required cement mechanical properties to withstand further deformation of the repaired system must be defined. From this information it can be determined whether available cement formulations meet these requirements. In addition to The Geysers, other geothermal fields are at possible risk of casing deformation due to subsidence, seismic activity, lateral and vertical formation movement or other processes. Therefore, the proposed remediation procedure may have applications in other fields.

  17. Appraisal of coal resources from uranium drill-hole logs, southern San Juan basin, New Mexico

    SciTech Connect (OSTI)

    Feldman, S.C.

    1984-04-01

    Geophysical logs from uranium drill holes in the Grants region are a valuable source of information on coal resources. Coal occurs in the southern San Juan basin of New Mexico in the Upper Cretaceous Gallup Sandstone, Crevasse Canyon Formation, and Menefee Formation. Uranium has been mined from the Upper Jurassic Morrison Formation that underlies the coal-bearing Cretaceous formations and is separated from them by approximately 1000 ft (300 m) of section. Permission was obtained from Santa Fe Mining, Inc., Pathfinder Mines Corp., and Ranchers Exploration and Development Corp. to examine their uranium drill logs for information on coal. Over 1400 logs spudded above the base of the Gallup formation were examined, and depth to coal, coal thickness, and coal stratigraphic horizon were determined for coal beds at least 3 ft (1 m) thick. Coal isopachs have been drawn, and depth from the surface to the first coal have been contoured for the Crevasse Canyon and Menefee Formations. Data from an earlier study, which used geophysical logs from petroleum test borings, has been incorporated. The relationship between the coal resources determined from uranium drill holes and known coal deposits and mines in the southern San Juan basin is discussed.

  18. Idaho National Laboratory PCB Annual Document Log and Annual Records Report for calendar year 2014

    SciTech Connect (OSTI)

    Layton, Deborah L.

    2015-06-01

    The requirements for the reporting of polychlorinated biphenyl (PCB)-related activities are found in 40 Code of Federal Regulations (CFR) 761 Subpart J, "General Records and Reports." The PCB Annual Document Log is a detailed record of the PCB waste handling activities at the facility. The facility must prepare it each year by July 1 and maintain it at the facility for at least 3 years after the facility ceases using or storing PCBs and PCB items. While submittal of the PCB Annual Document Log to the U.S. Environmental Protection Agency (EPA) is not required by regulation, EPA has verbally requested in telephone conversations that this report be submitted to them on an annual basis. The Annual Records are not required to be submitted to EPA and are not considered to be part of the Annual Document Log, but are included to provide the complete disposition history or status of all PCB activities during the year. The Annual Document Log section of this report (Section 2.0) meets the requirements of 40 CFR 761.180(a)(2), as applicable, while the Annual Records section (Section 3.0) meets the requirement of 40 CFR 761.180(a)(1).

  19. Qualified Energy Conservation Bond State-by-State Summary Tables

    Broader source: Energy.gov [DOE]

    Provides a list of qualified energy conservation bond state summary tables. Author: Energy Programs Consortium

  20. Permeability of consolidated incinerator facility wastes stabilized with portland cement

    SciTech Connect (OSTI)

    Walker, B.W.

    2000-04-19

    The Consolidated Incinerator Facility (CIF) at the Savannah River Site (SRS) burns low-level radioactive wastes and mixed wastes as a method of treatment and volume reduction. The CIF generates secondary waste, which consists of ash and offgas scrubber solution. Currently the ash is stabilized/solidified in the Ashcrete process. The scrubber solution (blowdown) is sent to the SRS Effluent Treatment Facility (ETF) for treatment as wastewater. In the past, the scrubber solution was also stabilized/solidified in the Ashcrete process as blowcrete, and will continue to be treated this way for listed waste burns and scrubber solutions that do not meet the ETF Waste Acceptance Criteria (WAC). The disposal plan for Ashcrete and special case blowcrete is to bury these containerized waste forms in shallow unlined trenches in E-Area. The WAC for intimately mixed, cement-based wasteforms intended for direct disposal specifies limits on compressive strength and permeability. Simulated waste and actual CIF ash and scrubber solution were mixed in the laboratory and cast into wasteforms for testing. Test results and related waste disposal consequences are given in this report.

  1. Epoxy bond and stop etch fabrication method

    DOE Patents [OSTI]

    Simmons, Jerry A.; Weckwerth, Mark V.; Baca, Wes E.

    2000-01-01

    A class of epoxy bond and stop etch (EBASE) microelectronic fabrication techniques is disclosed. The essence of such techniques is to grow circuit components on top of a stop etch layer grown on a first substrate. The first substrate and a host substrate are then bonded together so that the circuit components are attached to the host substrate by the bonding agent. The first substrate is then removed, e.g., by a chemical or physical etching process to which the stop etch layer is resistant. EBASE fabrication methods allow access to regions of a device structure which are usually blocked by the presence of a substrate, and are of particular utility in the fabrication of ultrafast electronic and optoelectronic devices and circuits.

  2. Process Of Bonding Copper And Tungsten

    DOE Patents [OSTI]

    Slattery, Kevin T.; Driemeyer, Daniel E.

    1999-11-23

    Process for bonding a copper substrate to a tungsten substrate by providing a thin metallic adhesion promoting film bonded to a tungsten substrate and a functionally graded material (FGM) interlayer bonding the thin metallic adhesion promoting film to the copper substrate. The FGM interlayer is formed by thermal plasma spraying mixtures of copper powder and tungsten powder in a varied blending ratio such that the blending ratio of the copper powder and the tungsten powder that is fed to a plasma torch is intermittently adjusted to provide progressively higher copper content/tungsten content, by volume, ratio values in the interlayer in a lineal direction extending from the tungsten substrate towards the copper substrate. The resulting copper to tungsten joint well accommodates the difference in the coefficient of thermal expansion of the materials.

  3. Bonded ultrasonic transducer and method for making

    DOE Patents [OSTI]

    Dixon, Raymond D.; Roe, Lawrence H.; Migliori, Albert

    1995-01-01

    An ultrasonic transducer is formed as a diffusion bonded assembly of piezoelectric crystal, backing material, and, optionally, a ceramic wear surface. The mating surfaces of each component are silver films that are diffusion bonded together under the application of pressure and heat. Each mating surface may also be coated with a reactive metal, such as hafnium, to increase the adhesion of the silver films to the component surfaces. Only thin silver films are deposited, e.g., a thickness of about 0.00635 mm, to form a substantially non-compliant bond between surfaces. The resulting transducer assembly is substantially free of self-resonances over normal operating ranges for taking resonant ultrasound measurements.

  4. Bonded ultrasonic transducer and method for making

    DOE Patents [OSTI]

    Dixon, R.D.; Roe, L.H.; Migliori, A.

    1995-11-14

    An ultrasonic transducer is formed as a diffusion bonded assembly of piezoelectric crystal, backing material, and, optionally, a ceramic wear surface. The mating surfaces of each component are silver films that are diffusion bonded together under the application of pressure and heat. Each mating surface may also be coated with a reactive metal, such as hafnium, to increase the adhesion of the silver films to the component surfaces. Only thin silver films are deposited, e.g., a thickness of about 0.00635 mm, to form a substantially non-compliant bond between surfaces. The resulting transducer assembly is substantially free of self-resonances over normal operating ranges for taking resonant ultrasound measurements. 12 figs.

  5. Method of bonding metals to ceramics

    DOE Patents [OSTI]

    Maroni, Victor A.

    1992-01-01

    A method of forming a composite by providing a ceramic capable of having zero electrical resistance and complete diamagnetism at superconducting temperatures, bonding a thin layer of Ag, Au or alloys thereof with the ceramic. Thereafter, there is bonded a first metal to the ceramic surface at a temperature less than about 400.degree. C., and then a second metal is bonded to the first metal at a temperature less than about 400.degree. C. to form a composite wherein the first metal is selected from the class consisting of In, Ga, Sn, Bi, Zn, Cd, Pb, Ti and alloys thereof and wherein the second metal is selected from the class consisting of Al, Cu, Pb and Zn and alloys thereof.

  6. Fundamental aspects of recoupled pair bonds. II. Recoupled pair bond dyads in carbon and sulfur difluoride

    SciTech Connect (OSTI)

    Dunning, Thom H. Takeshita, Tyler Y.; Xu, Lu T.

    2015-01-21

    Formation of a bond between a second ligand and a molecule with a recoupled pair bond results in a recoupled pair bond dyad. We examine the recoupled pair bond dyads in the a{sup 3}B{sub 1} states of CF{sub 2} and SF{sub 2}, which are formed by the addition of a fluorine atom to the a{sup 4}Σ{sup −} states of CF and SF, both of which possess recoupled pair bonds. The two dyads are very different. In SF{sub 2}, the second FS–F bond is very strong (D{sub e} = 106.3 kcal/mol), the bond length is much shorter than that in the SF(a{sup 4}Σ{sup −}) state (1.666 Å versus 1.882 Å), and the three atoms are nearly collinear (θ{sub e} = 162.7°) with only a small barrier to linearity (0.4 kcal/mol). In CF{sub 2}, the second FC–F bond is also very strong (D{sub e} = 149.5 kcal/mol), but the bond is only slightly shorter than that in the CF(a{sup 4}Σ{sup −}) state (1.314 Å versus 1.327 Å), and the molecule is strongly bent (θ{sub e} = 119.0°) with an 80.5 kcal/mol barrier to linearity. The a{sup 3}B{sub 1} states of CF{sub 2} and SF{sub 2} illustrate the fundamental differences between recoupled pair bond dyads formed from 2s and 3p lone pairs.

  7. Production of cements from Illinois coal ash. Technical report, September 1, 1995--November 30, 1995

    SciTech Connect (OSTI)

    Wagner, J.C.; Bhatty, J.I.; Mishulovich, A.

    1995-12-31

    The objective of this program is to convert Illinois coal combustion residues, such as fly ash, bottom ash, and boiler slag, into novel cementitious materials for use in the construction industry. Currently only about 30% of the 5 million tons of these coal combustion residues generated in Illinois each year are utilized, mainly as aggregate. These residues are composed largely Of SiO{sub 2}, Al{sub 2}O{sub 3}, Fe{sub 2}O{sub 3}, MgO, and CaO, which are also the major components of cement. The process being developed in this program will use the residues directly in the manufacture of cement products. Therefore, a much larger amount of residues can be utilized. To achieve the above objective, in the first phase (current year) samples of coal combustion residues will be blended and mixed, as needed, with a lime or cement kiln dust (CKD) to adjust the CaO composition. Six mixtures will be melted in a laboratory-scale furnace at CTL. The resulting products will then be tested for cementitious properties. Two preliminary blends have been tested. One blend used fly ash with limestone, while the other used fly ash with CKD. Each blend was melted and then quenched, and the resulting product samples were ground to a specific surface area similar to portland cement. Cementitious properties of these product samples were evaluated by compression testing of 1-inch cube specimens. The specimens were formed out of cement paste where a certain percentage of the cement paste is displaced by one of the sample products. The specimens were cured for 24 hours at 55{degrees}C and 100% relative humidity. The specimens made with the product samples obtained 84 and 89% of the strength of a pure portland cement control cube. For comparison, similar (pozzolanic) materials in standard concrete practice are required to have a compressive strength of at least 75% of that of the control.

  8. Evaluation of cement production using a pressurized fluidized-bed combustor

    SciTech Connect (OSTI)

    DeLallo, M.; Eshbach, R.

    1994-01-01

    There are several primary conclusions which can be reached and used to define research required in establishing the feasibility of using PFBC-derived materials as cement feedstock. 1. With appropriate blending almost any material containing the required cement-making materials can be utilized to manufacture cement. However, extensive blending with multiple materials or the use of ash in relatively small quantities would compromise the worth of this concept. 2. The composition of a potential feedstock must be considered not only with respect to the presence of required materials, but just as significantly, with respect to the presence and concentration of known deleterious materials. 3. The processing costs for rendering the feedstock into an acceptable composition and the energy costs associated with both processing and burning must be considered. It should be noted that the cost of energy to produce cement, expressed as a percentage of the price of the product is higher than for any other major industrial product. Energy consumption is, therefore, a major issue. 4. The need for conformance to environmental regulations has a profound effect on the cement industry since waste materials can neither be discharged to the atmosphere or be shipped to a landfill. 5. Fifth, the need for achieving uniformity in the composition of the cement is critical to controlling its quality. Unfortunately, certain materials in very small concentrations have the capability to affect the rate and extent to which the cementitious compound in portland cement are able to form. Particularly critical are variations in the ash, the sulfur content of the coal or the amount and composition of the stack dust returned to the kiln.

  9. Cementation and solidification of miscellaneous mixed wastes at the Rocky Flats Environmental Technology Site

    SciTech Connect (OSTI)

    Phillips, J.A.; Semones, G.B.

    1995-02-01

    The Rocky Flats Environmental Technology Site produces a variety of wastes which are amenable to micro-encapsulation in cement Portland cement is an inexpensive and readily available material for this application. The Waste Projects (WP) group at Rocky Flats evaluated cementation to determine its effectiveness in encapsulating several wastes. These included waste analytical laboratory solutions, incinerator ash, hydroxide precipitation sludge, and an acidic solution from the Delphi process (a chemical oxidation technology being evaluated as an alternative to incineration). WP prepared surrogate wastes and conducted designed experiments to optimize the cement formulation for the waste streams. These experiments used a Taguchi or factorial experimental design, interactions between the variables were also considered in the testing. Surrogate waste samples were spiked with various levels of each of six Resource Conservation and Recovery Act (RCRA) listed metals (Cd, Cr, Ba, Pb, Ni, and Ag), cemented using the optimized formulation, and analyzed for leach resistance using the Toxicity Characteristic Leaching Procedure (TCLP). The metal spike levels chosen were based on characterization data, and also based on an estimate of the highest levels of contaminants suspected in the waste. This paper includes laboratory test results for each waste studied. These include qualitative observations as well as quantitative data from TCLP analyses and environmental cycling studies. The results from these experiments show that cement stabilization of the different wastes can produce final waste forms which meet the current RCRA Land Disposal Restriction (LDR) requirements. Formulations that resulted in LDR compliant waste forms are provided. The volume increases associated with cementation are also lower than anticipated. Future work will include verification studies with actual mixed radioactive waste as well as additional formulation development studies on other waste streams.

  10. Adhesive bonding using variable frequency microwave energy

    DOE Patents [OSTI]

    Lauf, R.J.; McMillan, A.D.; Paulauskas, F.L.; Fathi, Z.; Wei, J.

    1998-08-25

    Methods of facilitating the adhesive bonding of various components with variable frequency microwave energy are disclosed. The time required to cure a polymeric adhesive is decreased by placing components to be bonded via the adhesive in a microwave heating apparatus having a multimode cavity and irradiated with microwaves of varying frequencies. Methods of uniformly heating various articles having conductive fibers disposed therein are provided. Microwave energy may be selectively oriented to enter an edge portion of an article having conductive fibers therein. An edge portion of an article having conductive fibers therein may be selectively shielded from microwave energy. 26 figs.

  11. Adhesive bonding using variable frequency microwave energy

    DOE Patents [OSTI]

    Lauf, R.J.; McMillan, A.D.; Paulauskas, F.L.; Fathi, Z.; Wei, J.

    1998-09-08

    Methods of facilitating the adhesive bonding of various components with variable frequency microwave energy are disclosed. The time required to cure a polymeric adhesive is decreased by placing components to be bonded via the adhesive in a microwave heating apparatus having a multimode cavity and irradiated with microwaves of varying frequencies. Methods of uniformly heating various articles having conductive fibers disposed therein are provided. Microwave energy may be selectively oriented to enter an edge portion of an article having conductive fibers therein. An edge portion of an article having conductive fibers therein may be selectively shielded from microwave energy. 26 figs.

  12. Adhesive bonding using variable frequency microwave energy

    DOE Patents [OSTI]

    Lauf, Robert J.; McMillan, April D.; Paulauskas, Felix L.; Fathi, Zakaryae; Wei, Jianghua

    1998-01-01

    Methods of facilitating the adhesive bonding of various components with variable frequency microwave energy are disclosed. The time required to cure a polymeric adhesive is decreased by placing components to be bonded via the adhesive in a microwave heating apparatus having a multimode cavity and irradiated with microwaves of varying frequencies. Methods of uniformly heating various articles having conductive fibers disposed therein are provided. Microwave energy may be selectively oriented to enter an edge portion of an article having conductive fibers therein. An edge portion of an article having conductive fibers therein may be selectively shielded from microwave energy.

  13. Bonded Radii and the Contraction of the Electron Density of the Oxygen Atom by Bonded Interactions

    SciTech Connect (OSTI)

    Gibbs, Gerald V.; Ross, Nancy L.; Cox, David F.; Rosso, Kevin M.; Iversen, Bo B.; Spackman, M. A.

    2013-02-21

    The bonded radii for more than 550 bonded pairs of atoms, comprising more than 50 crystals, determined from experimental and theoretical electron density distributions, are compared with the effective ionic, ri(M), and crystal radii, rc(M), for metal atoms, M, bonded to O atoms. At odds with the fixed ionic radius of 1.40 , assumed for the O atom in the compilation of the ionic radii, the bonded radius for the atom, rb(O), is not fixed but displays a relatively wide range of values as the O atom is progressively polarized by the M-O bonded interactions: as such, rb(O) decreases systematically from 1.40 (the Pauling radius of the oxide anion) as bond lengths decrease when bonded to an electropositive atom like sodium, to 0.64 (Braggs atomic radius of the O atom) when bonded to an electronegative atom like nitrogen. Both rb(M) and rb(O) increase in tandum with the increasing coordination number of the M atom. The bonded radii of the M atoms are highly correlated with both ri(M) and rc(M), but they both depart systematically from rb(M) and become smaller as the electronegativity of the M atom increases and the M-O bond length decreases. The well-developed correlations between both sets of radii and rb(M) testifies to the relative precision of both sets of radii and the fact that both sets are highly correlated the M-O bond 1 lengths. On the other hand, the progressive departure of rb(O) from the fixed ionic radius of the O atom with the increasing electronegativity of the bonded M atom indicates that any compilation of sets of ionic radii, assuming that the radius for the oxygen atom is fixed in value, is problematical and impacts on the accuracy of the resulting sets of ionic and crystal radii thus compiled. The assumption of a fixed O atom radius not only results in a negative ionic radii for several atoms, but it also results in values of rb(M) that are much as ~ 0.6 larger than the ri(M) and rc(M) values, respectively, particularly for the more

  14. Fluorinated diamond bonded in fluorocarbon resin

    DOE Patents [OSTI]

    Taylor, Gene W.

    1982-01-01

    By fluorinating diamond grit, the grit may be readily bonded into a fluorocarbon resin matrix. The matrix is formed by simple hot pressing techniques. Diamond grinding wheels may advantageously be manufactured using such a matrix. Teflon fluorocarbon resins are particularly well suited for using in forming the matrix.

  15. METHOD AND ALLOY FOR BONDING TO ZIRCONIUM

    DOE Patents [OSTI]

    McCuaig, F.D.; Misch, R.D.

    1960-04-19

    A brazing alloy can be used for bonding zirconium and its alloys to other metals, ceramics, and cermets, and consists of 6 to 9 wt.% Ni, 6 to 9 wn~.% Cr, Mo, or W, 0 to 7.5 wt.% Fe, and the balance Zr.

  16. Thermally stable, plastic-bonded explosives

    DOE Patents [OSTI]

    Benziger, Theodore M.

    1979-01-01

    By use of an appropriate thermoplastic rubber as the binder, the thermal stability and thermal stress characteristics of plastic-bonded explosives may be greatly improved. In particular, an HMX-based explosive composition using an oil-extended styrene-ethylenebutylene-styrene block copolymer as the binder exhibits high explosive energy and thermal stability and good handling safety and physical properties.

  17. Non-bonded piezoelectric ultrasonic transducer

    DOE Patents [OSTI]

    Eoff, James M.

    1985-01-01

    A mechanically assembled non-bonded ultrasonic transducer includes a substrate, a piezoelectric film, a wetting agent, a thin metal electrode, and a lens held in intimate contact by a mechanical clamp. No epoxy or glue is used in the assembly of this device.

  18. Correction of steel casing effect for density log using numerical and experimental methods in the slim borehole

    SciTech Connect (OSTI)

    Hwang, Seho; Shin, Jehyun; Kim, Jongman; Won, Byeongho

    2015-03-10

    Density log is widely applied for a variety of fields such as the petroleum exploration, mineral exploration, and geotechnical survey. The logging condition of density log is normally open holes but there are frequently cased boreholes. The primary calibration curve by slim hole logging manufacturer is normally the calibration curves for the variation of borehole diameter. In this study, we have performed the correction of steel casing effects using numerical and experimental methods. We have performed numerical modeling using the Monte Carlo N-Particle (MCNP) code based on Monte Carlo method, and field experimental method from open and cased hole log. In this study, we used the FDGS (Formation Density Gamma Sonde) for slim borehole with a 100 mCi 137Cs source, three inch borehole and steel casing. The casing effect between numerical and experimental method is well matched.

  19. Log-ratio signal-processing technique for beam position monitors

    SciTech Connect (OSTI)

    Shafer, R.E.

    1993-01-01

    Two basic signal-processing techniques are presently in wide use for the processing of signals from beam position monitors (BPMs); difference-over-sum, and amplitude-modulation-to-phase-modulation (AM-PM) conversion. Difference-over-sum offers simplicity and low cost, but poor real-time normalized response and amplitude dynamic range. AM-PM offers fast real-time response and large dynamic range, but is costly and difficult to implement. Logarithmic-ratio processing, a technique using newly available inexpensive hybrid circuits, appears to offer the advantages of both, and the disadvantages of neither. This paper reviews the features techniques, and highlights the features of the log-ratio technique. Among the advantages of log-ratio is a beam-displacement response linearity that is superior to either difference-over-sum or AM-PM for circular-aperture BPMs.

  20. Log-ratio signal-processing technique for beam position monitors

    SciTech Connect (OSTI)

    Shafer, R.E.

    1993-02-01

    Two basic signal-processing techniques are presently in wide use for the processing of signals from beam position monitors (BPMs); difference-over-sum, and amplitude-modulation-to-phase-modulation (AM-PM) conversion. Difference-over-sum offers simplicity and low cost, but poor real-time normalized response and amplitude dynamic range. AM-PM offers fast real-time response and large dynamic range, but is costly and difficult to implement. Logarithmic-ratio processing, a technique using newly available inexpensive hybrid circuits, appears to offer the advantages of both, and the disadvantages of neither. This paper reviews the features techniques, and highlights the features of the log-ratio technique. Among the advantages of log-ratio is a beam-displacement response linearity that is superior to either difference-over-sum or AM-PM for circular-aperture BPMs.

  1. Experimental approaches for the development of gamma spectroscopy well logging system

    SciTech Connect (OSTI)

    Shin, Jehyun; Hwang, Seho; Kim, Jongman; Won, Byeongho

    2015-03-10

    This article discusses experimental approaches for the development of gamma spectroscopy well logging system. Considering the size of borehole sonde, we customize 2 x 2 inches inorganic scintillators and the system including high voltage, preamplifier, amplifier and multichannel analyzer (MCA). The calibration chart is made by test using standard radioactive sources so that the measured count rates are expressed by energy spectrum. Optimum high-voltage supplies and the measurement parameters of each detector are set up by experimental investigation. Also, the responses of scintillation detectors have been examined by analysis according to the distance between source and detector. Because gamma spectroscopy well logging needs broad spectrum, high sensitivity and resolution, the energy resolution and sensitivity as a function of gamma ray energy are investigated by analyzing the gamma ray activities of the radioactive sources.

  2. 3-D Finite Element Analysis of Induction Logging in a Dipping Formation

    SciTech Connect (OSTI)

    EVERETT,MARK E.; BADEA,EUGENE A.; SHEN,LIANG C.; MERCHANT,GULAMABBAS A.; WEISS,CHESTER J.

    2000-07-20

    Electromagnetic induction by a magnetic dipole located above a dipping interface is of relevance to the petroleum well-logging industry. The problem is fully three-dimensional (3-D) when formulated as above, but reduces to an analytically tractable one-dimensional (1-D) problem when cast as a small tilted coil above a horizontal interface. The two problems are related by a simple coordinate rotation. An examination of the induced eddy currents and the electric charge accumulation at the interface help to explain the inductive and polarization effects commonly observed in induction logs from dipping geological formations. The equivalence between the 1-D and 3-D formulations of the problem enables the validation of a previously published finite element solver for 3-D controlled-source electromagnetic induction.

  3. U-038: BIND 9 Resolver crashes after logging an error in query.c

    Broader source: Energy.gov [DOE]

    A remote server can cause the target connected client to crash. Organizations across the Internet are reporting crashes interrupting service on BIND 9 nameservers performing recursive queries. Affected servers crash after logging an error in query.c with the following message: "INSIST(! dns_rdataset_isassociated(sigrdataset))" Multiple versions are reported as being affected, including all currently supported release versions of ISC BIND 9. ISC is actively investigating the root cause and working to produce patches which avoid the crash.

  4. U-039: ISC Update: BIND 9 Resolver crashes after logging an error in query.c

    Broader source: Energy.gov [DOE]

    A remote server can cause the target connected client to crash. Organizations across the Internet are reporting crashes interrupting service on BIND 9 nameservers performing recursive queries. Affected servers crash after logging an error in query.c with the following message: "INSIST(! dns_rdataset_isassociated(sigrdataset))" Multiple versions are reported as being affected, including all currently supported release versions of ISC BIND 9. ISC is actively investigating the root cause and working to produce patches which avoid the crash.

  5. Recognition of hydrocarbon expulsion using well logs: Bakken Formation, Williston Basin

    SciTech Connect (OSTI)

    Cunningham, R.; Zelt, F.B.; Morgan, S.R.; Passey, Q.R. ); Snavely, P.D. III; Webster, R.L. )

    1990-05-01

    The Upper Mississippian-Lower Devonian Bakken Formation forms a source/carrier/reservoir system in the Williston basin. Hydrocarbon expulsion within the Bakken has been identified by overlaying sonic and resistivity logs. Typically, these curves track in organically lean, water-saturated mudrocks because both respond mainly to porosity; however, in thermally mature organic-rich rocks and hydrocarbon reservoirs or carrier beds, the curves separate due to the anomalously high resistivity associated with replacement of pore water by hydrocarbons. Sonic/resistivity-log overlays for wells throughout the Montana and North Dakota parts of the Williston basin reveal significant increases and maximum in-curve separation within the middle siltstone member of the Bakken at subsurface temperatures of about 170 and 200{degree}F, respectively. Sequence-stratigraphic characteristics of the Bakken define the framework within which the expulsion process operates. The organic-rich upper and lower shale members represent the transgressive and early highstand systems tracts of two adjacent depositional sequences. A sequence boundary within the intervening middle siltstone member separates nearshore siltstone and sandstone of the late highstand systems tract in the lower sequence from cross-bedded subtidal to intertidal sandstones of the lowstand systems tract in the upper sequence. Reservoir properties vary across this sequence boundary. The authors attribute the log separation in the siltstone member to hydrocarbons expelled from the adjacent shales. Abrupt shifts in several geochemical properties of the shale members, indicative of hydrocarbon generation occur over the same subsurface temperature range as the rapid increase in log separation in the middle siltstone, thus indicating the contemporaneity of generation and expulsion.

  6. Evaluation of Non-Nuclear Techniques for Well Logging: Final Report

    SciTech Connect (OSTI)

    Bond, Leonard J.; Griffin, Jeffrey W.; Harris, R. V.; Denslow, Kayte M.; Moran, Traci L.

    2011-08-01

    The focus of this study is the understanding of the technical obstacles that hinder the replacement of and the disadvantages from the loss of extensive interpretation experience based on data accumulated with AmBe. Enhanced acoustic and electromagnetic sensing methods in combination with non-isotope-based well logging techniques have the potential to complement and/or replace existing isotope-based techniques, providing the opportunity to reduce oil industry dependence on isotopic sources such as AmBe.

  7. Fracture identification and evaluation using borehole imaging and full wave form logs in the Permian basin

    SciTech Connect (OSTI)

    Sanders, L. )

    1994-03-01

    The borehole imaging and acoustic full wave form logs provide an excellent means for identifying and evaluating naturally occurring fractures. The natural fractures can provide the porosity and permeability essential for a productive reservoir. The detection of these fractures may be accomplished by tow types of wireline logging tools: borehole imaging devices and acoustic full wave form tools. The borehole imaging tools produce images based upon the electromagnetic or the acoustic properties of the borehole wall. Fractures will appear as darker images that are distinct from the nonfracture formation. These images are coupled with a reference azimuth that allows for the determination of the orientation of the fracture image. The acoustic full wave form logs are used to detect fractures by analyzing various acoustic properties of the formation. The travel time, amplitude, and frequency responses of fractured formations differ remarkably from the responses of nonfractured formations because of the reduction of the acoustic energy in the fractures. The various field examples from the Queen sandstone to the Ellenburger formation demonstrate the advantages and disadvantages unique to the borehole imaging and the acoustic full wave form devices. Within this geologic framework, comparisons are made among the data extracted from whole cores, borehole imaging devices, and the acoustic full wave form tools in establishing a systematic approach for the identification and evaluation of fractures.

  8. {sup 1}H NMR relaxometry as an indicator of setting and water depletion during cement hydration

    SciTech Connect (OSTI)

    Wang, Biyun; Faure, Paméla; Thiéry, Mickaël; Baroghel-Bouny, Véronique

    2013-03-15

    Proton nuclear magnetic resonance relaxometry has been used to detect setting and microstructure evolution during cement hydration. NMR measurements were performed since casting, during setting and until hardening (from 0 to 3 days). The mobility of water molecules was assessed by an analysis focused on the diagram of longitudinal relaxation time T{sub 1} generated by an Inversion Recovery sequence. The initial stiffening of the solid network was identified by an analysis of the relaxation rate 1/T{sub 1}. The kinetics of water depletion was investigated by using a simple one-pulse acquisition sequence. In parallel, conventional techniques (Vicat needle and temperature monitoring), as well as numerical simulations of hydration, were used to complement and validate these NMR results. Cement pastes and mortars with different water-to-cement ratios made of grey or white OPCs were tested. Furthermore, the effects of the addition of sand, super-plasticizer and silica fume on the hydration kinetics were investigated.

  9. Hydration mechanisms of ternary Portland cements containing limestone powder and fly ash

    SciTech Connect (OSTI)

    De Weerdt, K.; Haha, M. Ben; Le Saout, G.; Kjellsen, K.O.; Justnes, H.; Lothenbach, B.

    2011-03-15

    The effect of minor additions of limestone powder on the properties of fly ash blended cements was investigated in this study using isothermal calorimetry, thermogravimetry (TGA), X-ray diffraction (XRD), scanning electron microscopy (SEM) techniques, and pore solution analysis. The presence of limestone powder led to the formation of hemi- and monocarbonate and to a stabilisation of ettringite compared to the limestone-free cements, where a part of the ettringite converted to monosulphate. Thus, the presence of 5% of limestone led to an increase of the volume of the hydrates, as visible in the increase in chemical shrinkage, and an increase in compressive strength. This effect was amplified for the fly ash/limestone blended cements due to the additional alumina provided by the fly ash reaction.

  10. The necessity for a practical approach to address organic emissions from cement kilns

    SciTech Connect (OSTI)

    Yonley, C.; Schreiber, B.; Kellerman, S.; Kellett, C.

    1998-12-31

    There is an inherent difficulty in monitoring organic emissions from hazardous waste combustion in the cement process. Data gathered by the EPA and the industry indicate that organic emissions at the main stack of cement kilns are principally from process characteristics and/or the desorption of organic constituents contained in the raw materials. Organic emissions are primarily based on the facility design and origin of the raw materials. One would generally conclude that organic emissions from fuels are essentially non-existent. To understand alternatives for monitoring organic emissions, this paper reviews some of the historical background behind the issue and reviews trends of characteristic organic emissions data. Based on this discussion and review, some approaches are presented to address organic emissions testing and monitoring when utilizing hazardous waste fuel in a cement kiln.

  11. Inorganic Corrosion-Inhibitive Pigments for High-Temperature Alkali-activated Well Casing Foam Cement

    SciTech Connect (OSTI)

    Sugama, T.; Pyatina, T.

    2014-11-01

    This study evaluates inorganic pigments for improving carbon steel (CS) brine-corrosion protection by the sodium metasilicate-activated calcium aluminate cement/Fly Ash blend at 300°C. Calcium borosilicate (CBS) and zinc phosphate, significantly improved CS corrosion-protection by decreasing cement’s permeability for corrosive ions and inhibiting anodic corrosion. An amorphous Na2O-Al2O3-SiO2-H2O phase tightly attached to CS surface formed at 300oC in CBS-modified cement pore solution. The corrosion rate of the CS covered with this phase was nearly 4-fold lower than in the case of nonmodified cement pore solution where the major phase formed on the surface of CS was crystalline analcime.

  12. Inorganic Corrosion-Inhibitive Pigments for High-Temperature Alkali-activated Well Casing Foam Cement

    SciTech Connect (OSTI)

    Sugama, T.; Pyatina, T.

    2014-11-14

    This study evaluates inorganic pigments for improving carbon steel (CS) brine-corrosion protection by the sodium metasilicate-activated calcium aluminate cement/Fly Ash blend at 300°C. Calcium borosilicate (CBS) and zinc phosphate, significantly improved CS corrosion-protection by decreasing cement’s permeability for corrosive ions and inhibiting anodic corrosion. An amorphous Na2O-Al2O3-SiO2-H2O phase tightly attached to CS surface formed at 300oC in CBS-modified cement pore solution. The corrosion rate of the CS covered with this phase was nearly 4-fold lower than in the case of nonmodified cement pore solution where the major phase formed on the surface of CS was crystalline analcime.

  13. Individual and combined effects of chloride, sulfate, and magnesium ions on hydrated Portland-cement paste

    SciTech Connect (OSTI)

    Poole, T.S.; Wakeley, L.D.; Young, C.L.

    1994-03-01

    Ground water with a high concentration of magnesium ion is known to cause deterioration to portland cement concretes. A proposed mechanism for this deterioration process published previously involves an approximate 1:1 replacement of Ca ions by Mg ions in the crystalline phases of hydrated cement. The current study was undertaken to determine which ions, among magnesium, chloride, and sulfate, cause deterioration; whether their deleterious action is individual or interdependent; and to relate this mechanism of deterioration to the outlook for a 100-yr service life of concretes used in mass placements at the Waste Isolation Pilot Plant. Loss of Ca ion by cement pastes was found to be strongly related to the concentration of Mg ion in simulated ground-water solutions in which the paste samples were aged. This was true of both salt- containing and conventional cement pastes. No other ion in the solutions exerted a strong effect on Ca loss. Ca ion left first from calcium hydroxide in the pastes, depleting all calcium hydroxide by 60 days. Some calcium silicate hydrate remained even after 90 days in the solutions with the highest concentration of Mg ion, while the paste samples deteriorated noticeably. The results indicated a mechanism that involves dissolution of Ca phases and transport of Ca ions to the surface of the sample, followed by formation of Mg-bearing phases at this reaction surface rather than directly by substitution within the microstructure of hydrated cement. Given that calcium hydroxide and calcium silicate hydrate are the principal strength-giving phases of hydrated cement, this mechanism indicates the likelihood of significant loss of integrity of a concrete exposed to Mg-bearing ground water at the WIPP. The rate of deterioration ultimately will depend on Mg-ion concentration, the microstructure materials of the concrete exposed to that groundwater, and the availability of brine.

  14. ASSESSMENT OF TECHNETIUM LEACHABILITY IN CEMENT STABILIZED BASIN 43 GROUNDWATER BRINE

    SciTech Connect (OSTI)

    COOKE GA; DUNCAN JB; LOCKREM LL

    2008-09-30

    This report is an initial report on the laboratory effort executed under RPP-PLAN-33338, Test Plan for the Assessment of Technetium Leachability in Cement-Stabilized Basin 43 Groundwater Brine. This report delineates preliminary data obtained under subcontract 21065, release 30, from the RJ Lee Group, Inc., Center for Laboratory Sciences. The report is predicated on CLS RPT-816, Draft Report: Assessment of Technetium Leachability in Cement Stabilized Basin 43 Groundwater Brine. This document will be revised on receipt of the final RJ Lee Group, Inc., Center for Laboratory Sciences report, which will contain data subjected to quality control and quality assurance criteria.

  15. Policy Options for Encouraging Energy Efficiency Best Practices in Shandong Province's Cement Industry

    SciTech Connect (OSTI)

    Price, Lynn; Zhou, Nan; Lu, Hongyou; Sambeek, Emiel van; Yowargana, Ping; Shuang, Liu; Kejun, Jiang

    2012-07-12

    This research intends to explore possible design options for a sectoral approach in the cement sector in Shandong Province and to consider its respective advantages and disadvantages for future application. An effort has been made in this research to gather and analyze data that will provide a transparent and robust basis for development of a Business-As-Usual (BAU) scenario, maximum technology potential scenario, and ultimately a sector crediting baseline. Surveys among cement companies and discussions with stakeholders were also conducted in order to better understand the industry and local needs related to the sectoral approach.

  16. Soil stabilization and pavement recycling with self-cementing coal fly ash

    SciTech Connect (OSTI)

    2008-01-15

    This manual provides design information for self-cementing coal fly ash as the sole stabilizing agent for a wide range of engineering applications. As in any process, the application of sound engineering practices, appropriate testing, and evaluation of fly ash quality and characteristics will lend themselves to successful projects using the guidelines in this manual. Topics discussed include: self-cementing coal fly ash characteristics; laboratory mix design; stabilization of clay soils; stabilisation of granular materials; construction considerations; high sulfate ash; environmental considerations for fly ash stabilization; design considerations; state specification/guidelines/standards; and a sample of a typical stabilization specification.

  17. CSER 00-001 Criticality Safety Evaluation Report for Cementation Operations at the PFP

    SciTech Connect (OSTI)

    DOBBIN, K.D.

    2000-04-18

    Glovebox HA-20MB is located in Room 235B of the 234-5Z Building at the Plutonium Finishing Plant. This enclosure contains mixers, mixer bowls, a crusher unit, an isolated inoperable conveyor unit, plutonium residue feed cans, cemented cans, and a feedwater container. Plutonium residue, not conducive to other forms of stabilization, is prepared for storage and ultimate disposal by cementation. The feed residue material cans can have plutonium contents of only a few grams or up to 200 grams. This evaluation accommodates this wide range of container fissile concentrations.

  18. A Signal-Inducing Bone Cement for Magnetic Resonance Imaging-Guided Spinal Surgery Based on Hydroxyapatite and Polymethylmethacrylate

    SciTech Connect (OSTI)

    Wichlas, Florian, E-mail: florian.wichlas@charite.de; Seebauer, Christian J.; Schilling, Rene [University Charite, Center for Musculoskeletal Surgery (Germany); Rump, Jens [University Charite, Department of Radiology (Germany); Chopra, Sascha S. [University Charite, Center for Musculoskeletal Surgery (Germany); Walter, Thula; Teichgraeber, Ulf K. M. [University Charite, Department of Radiology (Germany); Bail, Hermann J. [University Charite, Center for Musculoskeletal Surgery (Germany)

    2012-06-15

    The aim of this study was to develop a signal-inducing bone cement for magnetic resonance imaging (MRI)-guided cementoplasty of the spine. This MRI cement would allow precise and controlled injection of cement into pathologic lesions of the bone. We mixed conventional polymethylmethacrylate bone cement (PMMA; 5 ml methylmethacrylate and 12 g polymethylmethacrylate) with hydroxyapatite (HA) bone substitute (2-4 ml) and a gadolinium-based contrast agent (CA; 0-60 {mu}l). The contrast-to-noise ratio (CNR) of different CA doses was measured in an open 1.0-Tesla scanner for fast T1W Turbo-Spin-Echo (TSE) and T1W TSE pulse sequences to determine the highest signal. We simulated MRI-guided cementoplasty in cadaveric spines. Compressive strength of the cements was tested. The highest CNR was (1) 87.3 (SD 2.9) in fast T1W TSE for cements with 4 {mu}l CA/ml HA (4 ml) and (2) 60.8 (SD 2.4) in T1W TSE for cements with 1 {mu}l CA/ml HA (4 ml). MRI-guided cementoplasty in cadaveric spine was feasible. Compressive strength decreased with increasing amounts of HA from 46.7 MPa (2 ml HA) to 28.0 MPa (4 ml HA). An MRI-compatible cement based on PMMA, HA, and CA is feasible and clearly visible on MRI images. MRI-guided spinal cementoplasty using this cement would permit direct visualization of the cement, the pathologic process, and the anatomical surroundings.

  19. Bond order potential module for LAMMPS

    Energy Science and Technology Software Center (OSTI)

    2012-09-11

    pair_bop is a module for performing energy calculations using the Bond Order Potential (BOP) for use in the parallel molecular dynamics code LAMMPS. The bop pair style computes BOP based upon quantum mechanical incorporating both sigma and pi bondings. By analytically deriving the BOP pair bop from quantum mechanical theory its transferability to different phases can approach that of quantum mechanical methods. This potential is extremely effective at modeling 111-V and II-VI compounds such asmore » GaAs and CdTe. This potential is similar to the original BOP developed by Pettifor and later updated by Murdock et al. and Ward et al.« less

  20. Article coated with flash bonded superhydrophobic particles

    DOE Patents [OSTI]

    Simpson, John T [Clinton, TN; Blue, Craig A [Knoxville, TN; Kiggans, Jr., James O [Oak Ridge, TN

    2010-07-13

    A method of making article having a superhydrophobic surface includes: providing a solid body defining at least one surface; applying to the surface a plurality of diatomaceous earth particles and/or particles characterized by particle sizes ranging from at least 100 nm to about 10 .mu.m, the particles being further characterized by a plurality of nanopores, wherein at least some of the nanopores provide flow through porosity, the particles being further characterized by a plurality of spaced apart nanostructured features that include a contiguous, protrusive material; flash bonding the particles to the surface so that the particles are adherently bonded to the surface; and applying a hydrophobic coating layer to the surface and the particles so that the hydrophobic coating layer conforms to the nanostructured features.

  1. Reversible Sigma C-C Bond Formation Between Phenanthroline Ligands...

    Office of Scientific and Technical Information (OSTI)

    Reversible Sigma C-C Bond Formation Between Phenanthroline Ligands Activated by (C5Me5)2Yb Citation Details In-Document Search Title: Reversible Sigma C-C Bond Formation Between ...

  2. Pre-plated reactive diffusion-bonded battery electrode plaques

    DOE Patents [OSTI]

    Maskalick, Nicholas J.

    1984-01-01

    A high strength, metallic fiber battery plaque is made using reactive diffusion bonding techniques, where a substantial amount of the fibers are bonded together by an iron-nickel alloy.

  3. Fractional vortices in the XY model with {pi} bonds (Journal...

    Office of Scientific and Technical Information (OSTI)

    Fractional vortices in the XY model with pi bonds Citation Details In-Document Search Title: Fractional vortices in the XY model with pi bonds We define a new set of excitations ...

  4. Vacuum fusion bonding of glass plates

    DOE Patents [OSTI]

    Swierkowski, Steve P.; Davidson, James C.; Balch, Joseph W.

    2001-01-01

    An improved apparatus and method for vacuum fusion bonding of large, patterned glass plates. One or both glass plates are patterned with etched features such as microstructure capillaries and a vacuum pumpout moat, with one plate having at least one hole therethrough for communication with a vacuum pumpout fixture. High accuracy alignment of the plates is accomplished by a temporary clamping fixture until the start of the fusion bonding heat cycle. A complete, void-free fusion bond of seamless, full-strength quality is obtained through the plates; because the glass is heated well into its softening point and because of a large, distributed force that is developed that presses the two plates together from the difference in pressure between the furnace ambient (high pressure) and the channeling and microstructures in the plates (low pressure) due to the vacuum drawn. The apparatus and method may be used to fabricate microcapillary arrays for chemical electrophoresis; for example, any apparatus using a network of microfluidic channels embedded between plates of glass or similar moderate melting point substrates with a gradual softening point curve, or for assembly of glass-based substrates onto larger substrates, such as in flat panel display systems.

  5. Vacuum fusion bonding of glass plates

    DOE Patents [OSTI]

    Swierkowski, Steve P.; Davidson, James C.; Balch, Joseph W.

    2000-01-01

    An improved apparatus and method for vacuum fusion bonding of large, patterned glass plates. One or both glass plates are patterned with etched features such as microstructure capillaries and a vacuum pumpout moat, with one plate having at least one hole therethrough for communication with a vacuum pumpout fixture. High accuracy alignment of the plates is accomplished by a temporary clamping fixture until the start of the fusion bonding heat cycle. A complete, void-free fusion bond of seamless, full-strength quality is obtained through the plates; because the glass is heated well into its softening point and because of a large, distributed force that is developed that presses the two plates together from the difference in pressure between the furnace ambient (high pressure) and the channeling and microstructures in the plates (low pressure) due to the vacuum drawn. The apparatus and method may be used to fabricate microcapillary arrays for chemical electrophoresis; for example, any apparatus using a network of microfluidic channels embedded between plates of glass or similar moderate melting point substrates with a gradual softening point curve, or for assembly of glass-based substrates onto larger substrates, such as in flat panel display systems.

  6. Microchannel cooling of face down bonded chips

    DOE Patents [OSTI]

    Bernhardt, Anthony F.

    1993-01-01

    Microchannel cooling is applied to flip-chip bonded integrated circuits, in a manner which maintains the advantages of flip-chip bonds, while overcoming the difficulties encountered in cooling the chips. The technique is suited to either multichip integrated circuit boards in a plane, or to stacks of circuit boards in a three dimensional interconnect structure. Integrated circuit chips are mounted on a circuit board using flip-chip or control collapse bonds. A microchannel structure is essentially permanently coupled with the back of the chip. A coolant delivery manifold delivers coolant to the microchannel structure, and a seal consisting of a compressible elastomer is provided between the coolant delivery manifold and the microchannel structure. The integrated circuit chip and microchannel structure are connected together to form a replaceable integrated circuit module which can be easily decoupled from the coolant delivery manifold and the circuit board. The coolant supply manifolds may be disposed between the circuit boards in a stack and coupled to supplies of coolant through a side of the stack.

  7. Microchannel cooling of face down bonded chips

    DOE Patents [OSTI]

    Bernhardt, A.F.

    1993-06-08

    Microchannel cooling is applied to flip-chip bonded integrated circuits, in a manner which maintains the advantages of flip-chip bonds, while overcoming the difficulties encountered in cooling the chips. The technique is suited to either multi chip integrated circuit boards in a plane, or to stacks of circuit boards in a three dimensional interconnect structure. Integrated circuit chips are mounted on a circuit board using flip-chip or control collapse bonds. A microchannel structure is essentially permanently coupled with the back of the chip. A coolant delivery manifold delivers coolant to the microchannel structure, and a seal consisting of a compressible elastomer is provided between the coolant delivery manifold and the microchannel structure. The integrated circuit chip and microchannel structure are connected together to form a replaceable integrated circuit module which can be easily decoupled from the coolant delivery manifold and the circuit board. The coolant supply manifolds may be disposed between the circuit boards in a stack and coupled to supplies of coolant through a side of the stack.

  8. Thermal Modeling of A Friction Bonding Process

    SciTech Connect (OSTI)

    John Dixon; Douglas Burkes; Pavel Medvedev

    2007-10-01

    A COMSOL model capable of predicting temperature evolution during nuclear fuel fabrication is being developed at the Idaho National Laboratory (INL). Fuel plates are fabricated by friction bonding (FB) uranium-molybdenum (U-Mo) alloy foils positioned between two aluminum plates. The ability to predict temperature distribution during fabrication is imperative to ensure good quality bonding without inducing an undesirable chemical reaction between U-Mo and aluminum. A three-dimensional heat transfer model of the FB process implementing shallow pin penetration for cladding monolithic nuclear fuel foils is presented. Temperature distribution during the FB process as a function of fabrication parameters such as weld speed, tool load, and tool rotational frequency are predicted. Model assumptions, settings, and equations are described in relation to standard friction stir welding. Current experimental design for validation and calibration of the model is also demonstrated. Resulting experimental data reveal the accuracy in describing asymmetrical temperature distributions about the tool face. Temperature of the bonded plate drops beneath the pin and is higher on the advancing side than the retreating side of the tool.

  9. A Surprising Path for Proton Transfer Without Hydrogen Bonds

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    A Surprising Path for Proton Transfer Without Hydrogen Bonds A Surprising Path for Proton Transfer Without Hydrogen Bonds Print Wednesday, 25 July 2012 00:00 Hydrogen bonds are found everywhere in chemistry and biology and are critical in DNA and RNA. A hydrogen bond results from the attractive dipolar interaction of a chemical group containing a hydrogen atom with a group containing an electronegative atom, such as nitrogen, oxygen, or fluorine, in the same or a different molecule. Conventional

  10. Energetics of Hydrogen Bond Network Rearrangements in Liquid Water

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Energetics of Hydrogen Bond Network Rearrangements in Liquid Water Energetics of Hydrogen Bond Network Rearrangements in Liquid Water Print Wednesday, 25 May 2005 00:00 The unique chemical and physical properties of liquid water are thought to result from the highly directional hydrogen bonding (H-bonding) network structure and its associated dynamics. However, despite intense experimental and theoretical scrutiny, a complete description of this structure has been elusive. Recently, with the

  11. Taking Advantage of Qualified Energy Conservation Bonds | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energy Taking Advantage of Qualified Energy Conservation Bonds Taking Advantage of Qualified Energy Conservation Bonds This webinar, held on Sept. 22, 2010, provides information on qualified energy conservation bonds. Transcript Presentation (2.03 MB) More Documents & Publications Aggregating QECB Allocations and Using QECBs to Support the Private Sector: A Case Study on Massachusetts Making it Easier to Complete Clean Energy Projects with Qualified Energy Conservation Bonds (QECBs)

  12. Qualified Energy Conservation Bonds: Updates from the Field

    Office of Energy Efficiency and Renewable Energy (EERE)

    This webinar, held on March 28, 2011, focuses on qualified energy conservation bond updates, including issuance trends and performance contracting.

  13. Effect of radon transport in groundwater upon gamma-ray borehole logs

    SciTech Connect (OSTI)

    Nelson, P.H.; Rachiele, R.; Smith, A.

    1980-09-01

    Granitic rock at an experimental waste storage site at Stripa, Sweden, is unusually high in natural radioelements (40 ppM uranium) with higher concentrations occurring locally in thin chloritic zones and fractures. Groundwater seeping through fractures into open boreholes is consequently highly anomalous in its radon content, with activity as high as one microcurie per liter. When total count gamma-ray logs are run in boreholes where groundwater inflow is appreciable, the result is quite unusual: the radon daughter activity in the water adds considerably to the contribution from the rock, and in fact often dominates the log response. The total gamma activity increases where radon-charged groundwater enters a borehole, and remains at a high level as the water flows along the hole in response to the hydraulic gradient. As a consequence, the gamma log serves as a flow profile, locating zones of water entry (or loss) by an increase (or decrease) in the total gamma activity. A simple model has been developed for flow through a thin crack emanating radon at a rate E showing that the radon concentration of water entering a hole is E/..lambda..h, where ..lambda.. is the radon decay rate and h the crack aperture, assuming that the flow rate and crack source area are such that an element of water resides within the source area for several radon half-lives or more. Concentration measurements can provide a measurement of the inflow rate. Data from the 127-mm holes in the time-scale drift behave in this fashion.

  14. 1990 yearly calibration of Pacific Northwest Laboratory's gross-gamma borehole geophysical logging system

    SciTech Connect (OSTI)

    Arthur, R.J.

    1990-08-01

    This report describes the 1990 yearly calibration of a gross-gamma geophysical pulse logging system owned by the US Department of Energy (DOE) and operated by Pacific Northwest Laboratory (PNL). The calibration was conducted to permit the continued use of this system for geological and hydrologic studies associated with remedial investigation at the Hanford Site. Primary calibrations to equivalent uranium units were conducted in borehole model standards that were recently moved to the Hanford Site from the DOE field calibration facility in Spokane, Washington. The calibrations were performed in borehole models SBL/SBH and SBA/SBB, which contain low equivalent-uranium concentrations. The integrity of the system throughout the previous year from gamma-ray monitoring was demonstrated using the before- and after-logging field calibration readings with the field source in calibration Positions 1 and 2. Most of the Position 1 readings are within an 8% limit that is set by the governing PNL technical reference procedure as a critical value above which the instrument is considered suspect. Many of the Position 2 readings exceed the 8% limit; however, the fluctuation was traced to field-source geometry variability that affected Position 1 count rates by up to 6% and Position 2 count rates by as much as 16%. Correlations were established based on two similar approaches for relating observed count rate in before- and after-logging field calibrations to equivalent uranium concentrations. The temperature drift of the gamma-ray probe was documented and amounts to less than 0.1%/{degree}C within the temperature range 0{degree}C to 42{degree}C. The low-energy cutoff for the gross gamma-ray probe was determined to be between 46.5 and 59.5 keV. 10 refs., 4 figs., 13 tabs.

  15. Recovery Act Production of Algal BioCrude Oil from Cement Plant Carbon Dioxide

    SciTech Connect (OSTI)

    Robert Weber; Norman Whitton

    2010-09-30

    The consortium, led by Sunrise Ridge Algae Inc, completed financial, legal, siting, engineering and environmental permitting preparations for a proposed demonstration project that would capture stack gas from an operating cement plant and convert the carbon dioxide to beneficial use as a liquid crude petroleum substitute and a coal substitute, using algae grown in a closed system, then harvested and converted using catalyzed pyrolysis.

  16. Systematic approach for the design of pumpable cement-based grouts for immobilization of hazardous wastes

    SciTech Connect (OSTI)

    Sams, T.L.; Gilliam, T.M.

    1987-01-01

    Cement-based grouts have been proven to be an economical and environmentally acceptable means of waste disposal. Costs can be reduced if the grout is pumped to the disposal site. This paper presents a systematic approach to guide the development of pumpable grouts. 20 refs., 2 figs.

  17. Cement paste surface roughness analysis using coherence scanning interferometry and confocal microscopy

    SciTech Connect (OSTI)

    Apedo, K.L.; Munzer, C.; He, H.; Montgomery, P.; Serres, N.; Fond, C.; Feugeas, F.

    2015-02-15

    Scanning electron microscopy and scanning probe microscopy have been used for several decades to better understand the microstructure of cementitious materials. Very limited work has been performed to date to study the roughness of cementitious materials by optical microscopy such as coherence scanning interferometry (CSI) and chromatic confocal sensing (CCS). The objective of this paper is to better understand how CSI can be used as a tool to analyze surface roughness and topography of cement pastes. Observations from a series of images acquired using this technique on both polished and unpolished samples are described. The results from CSI are compared with those from a STIL confocal microscopy technique (SCM). Comparison between both optical techniques demonstrates the ability of CSI to measure both polished and unpolished cement pastes. - Highlights: • Coherence scanning interferometry (CSI) was used to analyze cement paste surfaces. • The results from the CSI were compared with those from a confocal microscopy. • 3D roughness parameters were obtained using the window resizing method. • Polished and unpolished cement pastes were studied.

  18. Improved microstructure of cement-based composites through the addition of rock wool particles

    SciTech Connect (OSTI)

    Lin, Wei-Ting; Cheng, An; Huang, Ran; Zou, Si-Yu

    2013-10-15

    Rock wool is an inorganic fibrous substance produced by steam blasting and cooling molten glass. As with other industrial by-products, rock wool particles can be used as cementitious materials or ultra fine fillers in cement-based composites. This study investigated the microstructure of mortar specimens produced with cement-based composites that include various forms of rock wool particles. It conducted compressive strength testing, rapid chloride penetration tests, X-ray diffraction analysis, thermo-gravimetric analysis, and scanning electronic microscopy to evaluate the macro- and micro-properties of the cement-based composites. Test results indicate that inclusion of rock wool particles in composites improved compressive strength and reduced chloride ion penetration at the age of 91 days due to the reduction of calcium hydroxide content. Microscopic analysis confirms that the use of rock wool particles contributed to the formation of a denser, more compact microstructure within the hardened paste. In addition, X-ray diffraction analysis shows few changes in formation of pozzolanic reaction products and no new hydrations are formed with incorporating rock wool particles. - Highlights: We report the microstructural characterization of cement-based composites. Different mixes produced with various rock wool particles have been tested. The influence of different mixes on macro and micro properties has been discussed. The macro properties are included compressive strength and permeability. XRD and SEM observations confirm the pozzolanic reaction in the resulting pastes.

  19. Method of assaying uranium with prompt fission and thermal neutron borehole logging adjusted by borehole physical characteristics. [Patient application

    DOE Patents [OSTI]

    Barnard, R.W.; Jensen, D.H.

    1980-11-05

    Uranium formations are assayed by prompt fission neutron logging techniques. The uranium in the formation is proportional to the ratio of epithermal counts to thermal or epithermal dieaway. Various calibration factors enhance the accuracy of the measurement.

  20. Method of assaying uranium with prompt fission and thermal neutron borehole logging adjusted by borehole physical characteristics

    DOE Patents [OSTI]

    Barnard, Ralston W.; Jensen, Dal H.

    1982-01-01

    Uranium formations are assayed by prompt fission neutron logging techniques. The uranium in the formation is proportional to the ratio of epithermal counts to thermal or eqithermal dieaway. Various calibration factors enhance the accuracy of the measurement.

  1. High-voltage supply for neutron tubes in well-logging applications

    DOE Patents [OSTI]

    Humphreys, D.R.

    1982-09-15

    A high voltage supply is provided for a neutron tube used in well logging. The biased pulse supply of the invention combines DC and full pulse techniques and produces a target voltage comprising a substantial negative DC bias component on which is superimposed a pulse whose negative peak provides the desired negative voltage level for the neutron tube. The target voltage is preferably generated using voltage doubling techniques and employing a voltage source which generates bipolar pulse pairs having an amplitude corresponding to the DC bias level.

  2. LITERATURE SURVEY ON CEMENTS FOR REMEDIATION OF DEFORMED CASING IN GEOTHERMAL WELLS

    SciTech Connect (OSTI)

    ALLAN,M.L.; PHILIPPACOPOULOS,A.J.

    1998-11-01

    Brookhaven National Laboratory was requested to conduct a literature survey for the best available cement to use in the proposed casing patch as part of the Geothermal Drilling Organization (GDO) project on remediation of deformed casings. A total of 50 wells has been identified with deformed production casing in Unocal's portion of The Geysers geothermal field. Reduced internal diameter and casing doglegs result in lost production and the possible need for abandonment. The cause of the deformations is believed to be formation movement along fault planes and/or along weaker layers or interfaces between high impedance contrast media. Apparently, it is unclear whether shear or axial compression is the dominant failure mechanism. A procedure to address the casing deformation and avoid abandonment of these wells has been developed as described in the Geysers Deformed Casing Remediation Proposal. The proposed remediation procedure involves isolation of the zone of interest with an inflatable packer, milling the deformed casing and cementing a 7 inch diameter liner to extend approximately 100 ft above and 100 ft below the milled zone. During the milling operation it is possible that the original cement and surrounding formation may slough away. In order to specify a suitable cement formulation for the casing patch it is first necessary to identify and understand the deformation mechanism/s operating in The Geysers field. Subsequently, the required cement mechanical properties to withstand further deformation of the repaired system must be defined. From this information it can be determined whether available cement formulations meet these requirements. In addition to The Geysers, other geothermal fields are at possible risk of casing deformation due to subsidence, seismic activity, lateral and vertical formation movement or other processes. Therefore, the proposed remediation procedure may have applications in other fields. The literature survey focused on published

  3. Emerging Energy-efficiency and CO{sub 2} Emission-reduction Technologies for Cement and Concrete Production

    SciTech Connect (OSTI)

    Hasanbeigi, Ali; Price, Lynn; Lin, Elina

    2012-04-06

    Globally, the cement industry accounts for approximately 5 percent of current anthropogenic carbon dioxide (CO{sub 2}) emissions. World cement demand and production are increasing significantly, leading to an increase in this industry's absolute energy use and CO{sub 2} emissions. Development of new energy-efficiency and CO{sub 2} emission-reduction technologies and their deployment in the market will be key for the cement industry's mid- and long-term climate change mitigation strategies. This report is an initial effort to compile available information on process description, energy savings, environmental and other benefits, costs, commercialization status, and references for emerging technologies to reduce the cement industry's energy use and CO{sub 2} emissions. Although studies from around the world identify a variety of sector-specific and cross-cutting energy-efficiency technologies for the cement industry that have already been commercialized, information is scarce and/or scattered regarding emerging or advanced energy-efficiency and low-carbon technologies that are not yet commercialized. This report consolidates available information on nineteen emerging technologies for the cement industry, with the goal of providing engineers, researchers, investors, cement companies, policy makers, and other interested parties with easy access to a well-structured database of information on these technologies.

  4. Determining the slag fraction, water/binder ratio and degree of hydration in hardened cement pastes

    SciTech Connect (OSTI)

    Yio, M.H.N. Phelan, J.C.; Wong, H.S.; Buenfeld, N.R.

    2014-02-15

    A method for determining the original mix composition of hardened slag-blended cement-based materials based on analysis of backscattered electron images combined with loss on ignition measurements is presented. The method does not require comparison to reference standards or prior knowledge of the composition of the binders used. Therefore, it is well-suited for application to real structures. The method is also able to calculate the degrees of reaction of slag and cement. Results obtained from an experimental study involving sixty samples with a wide range of water/binder (w/b) ratios (0.30 to 0.50), slag/binder ratios (0 to 0.6) and curing ages (3 days to 1 year) show that the method is very promising. The mean absolute errors for the estimated slag, water and cement contents (kg/m{sup 3}), w/b and s/b ratios were 9.1%, 1.5%, 2.5%, 4.7% and 8.7%, respectively. 91% of the estimated w/b ratios were within 0.036 of the actual values. -- Highlights: •A new method for estimating w/b ratio and slag content in cement pastes is proposed. •The method is also able to calculate the degrees of reaction of slag and cement. •Reference standards or prior knowledge of the binder composition are not required. •The method was tested on samples with varying w/b ratios and slag content.

  5. Groundwater flow, late cementation, and petroleum accumulation the Permian Lyons Sandstone, Denver basin

    SciTech Connect (OSTI)

    Lee, M.K.; Bethke, C.M. )

    1994-02-01

    The gray diagenetic facies of the Permian Lyons Sandstone, associated with all known petroleum accumulations in the formation, formed late in the history of the Denver basin as an alteration product of the formation's red facies. The red facies that makes up most of the sandstone contains iron oxide coating, quartz overgrowths and calcite cements. The gray facies, which occurs locally in the deep basin, is distinguished by pore-filling dolomite and anhydrite cements and by a lack of iron oxide and calcite. The dolomite and anhydrite cements overlie bitumen that was deposited by migrating oil, and hence formed after oil was first generated in the basin, late in the Cretaceous or early in the Tertiary. The isotopic composition of oxygen in the dolomite ranges to such light values that the cement must have formed deep in the basin in the presence of meteoric water. The gray facies likely formed in a regime of groundwater flow resulting from Laramide uplift of the Front Range during the Tertiary. In our model, saline groundwater flowed eastward through the Pennsylvanian Fountain Formation and then upwelled along the basin axis, where is discharged into the Lyons Sandstone. The saline water mixed with more dilute groundwater in the Lyons, driving a reaction that dissolved calcite and, by a common-ion effect, precipitated dolomite and anhydrite. The facies' gray color resulted from reduction of ferric oxide in the presence of migrating oil or the Fountain brine. Underlying source beds by this time had begun to generate petroleum, which migrated by buoyancy into the Lyons. The association of the gray facies with petroleum accumulations can be explained if the Fountain brines discharged across aquitards along the same fractures that transmitted oil. As petroleum accumulated in the Lyons, the newly formed cements prevented continued migration, as is observed in shallower strata, by sealing oil into the reservoirs from which it is produced today. 77 refs., 16 figs., 5 tabs.

  6. Method for bonding a transmission line to a downhole tool

    DOE Patents [OSTI]

    Hall, David R.; Fox, Joe

    2007-11-06

    An apparatus for bonding a transmission line to the central bore of a downhole tool includes a pre-formed interface for bonding a transmission line to the inside diameter of a downhole tool. The pre-formed interface includes a first surface that substantially conforms to the outside contour of a transmission line and a second surface that substantially conforms to the inside diameter of a downhole tool. In another aspect of the invention, a method for bonding a transmission line to the inside diameter of a downhole tool includes positioning a transmission line near the inside wall of a downhole tool and placing a mold near the transmission line and the inside wall. The method further includes injecting a bonding material into the mold and curing the bonding material such that the bonding material bonds the transmission line to the inside wall.

  7. Bond selective chemistry beyond the adiabatic approximation

    SciTech Connect (OSTI)

    Butler, L.J.

    1993-12-01

    One of the most important challenges in chemistry is to develop predictive ability for the branching between energetically allowed chemical reaction pathways. Such predictive capability, coupled with a fundamental understanding of the important molecular interactions, is essential to the development and utilization of new fuels and the design of efficient combustion processes. Existing transition state and exact quantum theories successfully predict the branching between available product channels for systems in which each reaction coordinate can be adequately described by different paths along a single adiabatic potential energy surface. In particular, unimolecular dissociation following thermal, infrared multiphoton, or overtone excitation in the ground state yields a branching between energetically allowed product channels which can be successfully predicted by the application of statistical theories, i.e. the weakest bond breaks. (The predictions are particularly good for competing reactions in which when there is no saddle point along the reaction coordinates, as in simple bond fission reactions.) The predicted lack of bond selectivity results from the assumption of rapid internal vibrational energy redistribution and the implicit use of a single adiabatic Born-Oppenheimer potential energy surface for the reaction. However, the adiabatic approximation is not valid for the reaction of a wide variety of energetic materials and organic fuels; coupling between the electronic states of the reacting species play a a key role in determining the selectivity of the chemical reactions induced. The work described below investigated the central role played by coupling between electronic states in polyatomic molecules in determining the selective branching between energetically allowed fragmentation pathways in two key systems.

  8. Special purpose revenue bonds: boon or bane

    SciTech Connect (OSTI)

    Taussig, R.A.

    1985-02-21

    Utilities are looking with increasing interest at the advantages offered by industrial development bonds (IDBs), a financing tool made available to investor-owned utilities through provision of federal law. IDBs are not without problems, however, particularly if regulatory agencies account for them improperly in rate cases. Regulatory agencies should allow returns based on the funds-used rather than the total-funds approach or the tariffs will not compensate investors adequately. The author examines both the risks to be avoided and the benefits when using IDBs.

  9. Printability Optimization For Fine Pitch Solder Bonding

    SciTech Connect (OSTI)

    Kwon, Sang-Hyun; Lee, Chang-Woo; Yoo, Sehoon

    2011-01-17

    Effect of metal mask and pad design on solder printability was evaluated by DOE in this study. The process parameters were stencil thickness, squeegee angle, squeegee speed, mask separating speed, and pad angle of PCB. The main process parameters for printability were stencil thickness and squeegee angle. The response surface showed that maximum printability of 1005 chip was achieved at the stencil thickness of 0.12 mm while the maximum printability of 0603 and 0402 chip was obtained at the stencil thickness of 0.05 mm. The bonding strength of the MLCC chips was also directly related with the printability.

  10. Repairable chip bonding/interconnect process

    DOE Patents [OSTI]

    Bernhardt, A.F.; Contolini, R.J.; Malba, V.; Riddle, R.A.

    1997-08-05

    A repairable, chip-to-board interconnect process which addresses cost and testability issues in the multi-chip modules is disclosed. This process can be carried out using a chip-on-sacrificial-substrate technique, involving laser processing. This process avoids the curing/solvent evolution problems encountered in prior approaches, as well is resolving prior plating problems and the requirements for fillets. For repairable high speed chip-to-board connection, transmission lines can be formed on the sides of the chip from chip bond pads, ending in a gull wing at the bottom of the chip for subsequent solder. 10 figs.

  11. METHOD OF MAKING METAL BONDED CARBON BODIES

    DOE Patents [OSTI]

    Goeddel, W.V.; Simnad, M.T.

    1961-09-26

    A method of producing carbon bodies having high structural strength and low permeability is described. The method comprises mixing less than 10 wt.% of a diffusional bonding material selected from the group consisting of zirconium, niobium, molybdenum, titanium, nickel, chromium, silicon, and decomposable compounds thereof with finely divided particles of carbon or graphite. While being maintained at a mechanical pressure over 3,000 psi, the mixture is then heated uniformly to a temperature of 1500 deg C or higher, usually for less than one hour. The resulting carbon bodies have a low diffusion constant, high dimensional stability, and high mechanical strength.

  12. Repairable chip bonding/interconnect process

    DOE Patents [OSTI]

    Bernhardt, Anthony F.; Contolini, Robert J.; Malba, Vincent; Riddle, Robert A.

    1997-01-01

    A repairable, chip-to-board interconnect process which addresses cost and testability issues in the multi-chip modules. This process can be carried out using a chip-on-sacrificial-substrate technique, involving laser processing. This process avoids the curing/solvent evolution problems encountered in prior approaches, as well is resolving prior plating problems and the requirements for fillets. For repairable high speed chip-to-board connection, transmission lines can be formed on the sides of the chip from chip bond pads, ending in a gull wing at the bottom of the chip for subsequent solder.

  13. The application of moment methods to the analysis of fluid electrical conductivity logs in boreholes

    SciTech Connect (OSTI)

    Loew, S. ); Tsang, Chin-Fu; Hale, F.V. ); Hufschmied, P. , Baden )

    1990-08-01

    This report is one of a series documenting the results of the Nagra-DOE Cooperative (NDC-I) research program in which the cooperating scientists explore the geological, geophysical, hydrological, geochemical, and structural effects anticipated from the use of a rock mass as a geologic repository for nuclear waste. Previous reports have presented a procedure for analyzing a time sequence of wellbore electric conductivity logs in order to obtain outflow parameters of fractures intercepted by the borehole, and a code, called BORE, used to simulate borehole fluid conductivity profiles given these parameters. The present report describes three new direct (not iterative) methods for analyzing a short time series of electric conductivity logs based on moment quantities of the individual outflow peaks and applies them to synthetic as well as to field data. The results of the methods discussed show promising results and are discussed in terms of their respective advantages and limitations. In particular it is shown that one of these methods, the so-called Partial Moment Method,'' is capable of reproducing packer test results from field experiments in the Leuggern deep well within a factor of three, which is below the range of what is recognized as the precision of packer tests themselves. Furthermore the new method is much quicker than the previously used iterative fitting procedure and is even capable of handling transient fracture outflow conditions. 20 refs., 11 figs., 10 tabs.

  14. Calibration of NMR well logs from carbonate reservoirs with laboratory NMR measurements and μXRCT

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Mason, Harris E.; Smith, Megan M.; Hao, Yue; Carroll, Susan A.

    2014-12-31

    The use of nuclear magnetic resonance (NMR) well log data has the potential to provide in-situ porosity, pore size distributions, and permeability of target carbonate CO₂ storage reservoirs. However, these methods which have been successfully applied to sandstones have yet to be completely validated for carbonate reservoirs. Here, we have taken an approach to validate NMR measurements of carbonate rock cores with independent measurements of permeability and pore surface area to volume (S/V) distributions using differential pressure measurements and micro X-ray computed tomography (μXRCT) imaging methods, respectively. We observe that using standard methods for determining permeability from NMR data incorrectlymore » predicts these values by orders of magnitude. However, we do observe promise that NMR measurements provide reasonable estimates of pore S/V distributions, and with further independent measurements of the carbonate rock properties that universally applicable relationships between NMR measured properties may be developed for in-situ well logging applications of carbonate reservoirs.« less

  15. Evaluation of Non-Nuclear Techniques for Well Logging: Technology Evaluation

    SciTech Connect (OSTI)

    Bond, Leonard J.; Denslow, Kayte M.; Griffin, Jeffrey W.; Dale, Gregory E.; Harris, Robert V.; Moran, Traci L.; Sheen, David M.; Schenkel, Thomas

    2010-11-01

    This report presents an initial review of the state-of-the-art nuclear and non-nuclear well logging methods and seeks to understand the technical and economic issues if AmBe, and potentially other isotope sources, are reduced or even eliminated in the oil-field services industry. Prior to considering alternative logging technologies, there is a definite need to open up discussions with industry regarding the feasibility and acceptability of source replacement. Industry views appear to range from those who see AmBe as vital and irreplaceable to those who believe that, with research and investment, it may be possible to transition to electronic neutron sources and employ combinations of non-nuclear technologies to acquire the desired petro-physical parameters. In one sense, the simple answer to the question as to whether petro-physical parameters can be sensed with technologies other than AmBe is probably "Yes". The challenges come when attention turns to record interpretation. The many decades of existing records form a very valuable proprietary resource, and the interpretation of subtle features contained in these records are of significant value to the oil-gas exploration community to correctly characterize a well. The demonstration of equivalence and correspondence/correlation between established and any new sensing modality, and correlations with historic records is critical to ensuring accurate data interpretation. Establishing the technical basis for such a demonstration represents a significant effort.

  16. Chemically bonded phospho-silicate ceramics

    DOE Patents [OSTI]

    Wagh, Arun S.; Jeong, Seung Y.; Lohan, Dirk; Elizabeth, Anne

    2003-01-01

    A chemically bonded phospho-silicate ceramic formed by chemically reacting a monovalent alkali metal phosphate (or ammonium hydrogen phosphate) and a sparsely soluble oxide, with a sparsely soluble silicate in an aqueous solution. The monovalent alkali metal phosphate (or ammonium hydrogen phosphate) and sparsely soluble oxide are both in powder form and combined in a stochiometric molar ratio range of (0.5-1.5):1 to form a binder powder. Similarly, the sparsely soluble silicate is also in powder form and mixed with the binder powder to form a mixture. Water is added to the mixture to form a slurry. The water comprises 50% by weight of the powder mixture in said slurry. The slurry is allowed to harden. The resulting chemically bonded phospho-silicate ceramic exhibits high flexural strength, high compression strength, low porosity and permeability to water, has a definable and bio-compatible chemical composition, and is readily and easily colored to almost any desired shade or hue.

  17. Solving the Mystery of the Billion-Dollar Bond, Double Bond

    Broader source: Energy.gov [DOE]

    Plant fatty acids are used in a vast range of products, from polymers to plastics and soaps to industrial feed stocks -- making up an estimated $150 billion market annually. A new discovery of inserting double bonds in the fatty acids could show the way to the designer production of plant fatty acids, and, in turn, to new industrial applications and new products.

  18. Use of X-ray diffraction to quantify amorphous supplementary cementitious materials in anhydrous and hydrated blended cements

    SciTech Connect (OSTI)

    Snellings, R.; Salze, A.; Scrivener, K.L.

    2014-10-15

    The content of individual amorphous supplementary cementitious materials (SCMs) in anhydrous and hydrated blended cements was quantified by the PONKCS [1] X-ray diffraction (XRD) method. The analytical precision and accuracy of the method were assessed through comparison to a series of mixes of known phase composition and of increasing complexity. A 2σ precision smaller than 2–3 wt.% and an accuracy better than 2 wt.% were achieved for SCMs in mixes with quartz, anhydrous Portland cement, and hydrated Portland cement. The extent of reaction of SCMs in hydrating binders measured by XRD was 1) internally consistent as confirmed through the standard addition method and 2) showed a linear correlation to the cumulative heat release as measured independently by isothermal conduction calorimetry. The advantages, limitations and applicability of the method are discussed with reference to existing methods that measure the degree of reaction of SCMs in blended cements.

  19. CHARACTERIZATION OF MONOLITHIC FUEL FOIL PROPERTIES AND BOND STRENGTH

    SciTech Connect (OSTI)

    D E Burkes; D D Keiser; D M Wachs; J S Larson; M D Chapple

    2007-03-01

    Understanding fuel foil mechanical properties, and fuel / cladding bond quality and strength in monolithic plates is an important area of investigation and quantification. Specifically, what constitutes an acceptable monolithic fuel – cladding bond, how are the properties of the bond measured and determined, and what is the impact of fabrication process or change in parameters on the level of bonding? Currently, non-bond areas are quantified employing ultrasonic determinations that are challenging to interpret and understand in terms of irradiation impact. Thus, determining mechanical properties of the fuel foil and what constitutes fuel / cladding non-bonds is essential to successful qualification of monolithic fuel plates. Capabilities and tests related to determination of these properties have been implemented at the INL and are discussed, along with preliminary results.

  20. Assessing the effect of cement-steel interface on well casing corrosion in aqueous CO2 environments

    SciTech Connect (OSTI)

    Han, Jiabin; Carey, James W; Zhang, Jinsuo

    2010-01-01

    CO{sub 2} leakage is a critical safety concern for geologic storage. In wellbore environments, important leakage paths include the rock-cement and cement-casing interfaces. If the cement-casing interface is filled with escaping CO{sub 2}, the well casing directly contacts the CO{sub 2}. This can cause severe corrosion in the presence of water. This paper studies the effect of steel-cement interface gaps, ranging from 1 mm to 0 um, on casing corrosion. Corrosion kinetics were measured employing electrochemical techniques including linear polarization resistance, open circuit potential and electrochemical impedance spectroscopy. The experimental results showed that the corrosion of steel is not significant where the gap between steel and cement is small ({le} 100 {micro}m). Corrosion rates are controlled by the diffusion of corrosive species (H{sub 2}CO{sub 3} and H{sup +}) along the interface. In contrast, steel corrosion is severe in a broad gap where the corrosion process is limited only by the reaction kinetics of steel and corrosive species. The threshold leading to severe corrosion in terms of the cement-steel interface size (100 {micro}m) was determined. Our research clarifies a corrosion scenario at the cement-steel interface. Casing steel corrosion is initiated when attacked by corrosive species at the cement-steel interface. For relatively tight interfaces, this results in a slow thinning of the casing and expansion of the interface width. If the gap increases beyond the critical threshold size, the corrosion rate increases significantly, and a potentially damaging cycle of corrosion and interface expansion is developed.