National Library of Energy BETA

Sample records for log stoneley analysis

  1. Sisyphus - An Event Log Analysis Toolset

    Energy Science and Technology Software Center (OSTI)

    2004-09-01

    Event logs are a ubiquitous source of system feedback from computer systems, but have widely ranging format and can be extremely numerous, particularly from systems with many logging components. Inspection of these logs is fundamental to system debugging; increased capability to quickly extract meaningful information will impact MTTR (mean time to repair) and may impact MTBF (mean time between failure). Sisyphus is a machine-leanring analysis system whose goal is to enable content-novice analysts to efficieniiymore » understand evolving trends, identify anomalies, and investigate cause-effect hypotheses in large multiple-souce log sets. The toolkit is comprised a framework for utilizing third-party frequentitemset data mining tools Teiresias and SLCT. and software to cluster messages according to time statistics, and an interactive results viewer.« less

  2. Conversion of borehole Stoneley waves to channel waves in coal

    SciTech Connect (OSTI)

    Johnson, P.A.; Albright, J.N.

    1987-01-01

    Evidence for the mode conversion of borehole Stoneley waves to stratigraphically guided channel waves was discovered in data from a crosswell acoustic experiment conducted between wells penetrating thin coal strata located near Rifle, Colorado. Traveltime moveout observations show that borehole Stoneley waves, excited by a transmitter positioned at substantial distances in one well above and below a coal stratum at 2025 m depth, underwent partial conversion to a channel wave propagating away from the well through the coal. In an adjacent well the channel wave was detected at receiver locations within the coal, and borehole Stoneley waves, arising from a second partial conversion of channel waves, were detected at locations above and below the coal. The observed channel wave is inferred to be the third-higher Rayleigh mode based on comparison of the measured group velocity with theoretically derived dispersion curves. The identification of the mode conversion between borehole and stratigraphically guided waves is significant because coal penetrated by multiple wells may be detected without placing an acoustic transmitter or receiver within the waveguide. 13 refs., 6 figs., 1 tab.

  3. INSPIRE and SPIRES Log File Analysis

    SciTech Connect (OSTI)

    Adams, Cole; /Wheaton Coll. /SLAC

    2012-08-31

    SPIRES, an aging high-energy physics publication data base, is in the process of being replaced by INSPIRE. In order to ease the transition from SPIRES to INSPIRE it is important to understand user behavior and the drivers for adoption. The goal of this project was to address some questions in regards to the presumed two-thirds of the users still using SPIRES. These questions are answered through analysis of the log files from both websites. A series of scripts were developed to collect and interpret the data contained in the log files. The common search patterns and usage comparisons are made between INSPIRE and SPIRES, and a method for detecting user frustration is presented. The analysis reveals a more even split than originally thought as well as the expected trend of user transition to INSPIRE.

  4. Templates and Examples — Statistics and Search Log Analysis

    Broader source: Energy.gov [DOE]

    Here you will find custom templates and EERE-specific examples you can use to plan, conduct, and report on your usability and analysis activities. These templates are examples of forms you might use, but you are not required to use them for EERE products.

  5. Mud Logging | Open Energy Information

    Open Energy Info (EERE)

    Well Log Techniques Acoustic Logs Cement Bond Log Cross-Dipole Acoustic Log Caliper Log Chemical Logging Density Log Gamma Log Image Logs Mud Logging Neutron Log Pressure...

  6. Change Log

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NERSC-8 Trinity Benchmarks Change Log 09032013 Correction applied to MiniDFT web-page ... results spreadsheet (linked on SSP web page); clarification to benchmark run rules ...

  7. Change Log

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Change Log Change Log Crossroads/NERSC-9 Benchmarks Change Log 03/04/2016 Updated PENNANT benchmark. Updated SSI spreadsheet to reflect new PENNANT reference timing. 02/29/2016 Updated MPI Benchmarks section. Added link for SMB multi-threaded MPI benchmarks, which are to be used for message rate and latency measurements called out in the Application Performance section of the RFP. 02/26/2016 New miniPIC distribution: 1) Updated source and README.APEX, 2) FOM is now updates/second, 3) Edison

  8. Change Log

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Change Log Change Log NERSC-8 / Trinity Benchmarks Change Log 09/03/2013 Correction applied to MiniDFT web-page (to remove inconsistency with MiniDFT README). Capability Improvement measurements do not require 10,000 MPI ranks per k-point. 08/06/2013 Various pages have changed to remove "draft" status 08/02/2013 Correction added to FLOP Counts for "Small" Single-Node Miniapplication Tests page 07/12/2013 README files updated for IOR benchmark to correct an error in wording

  9. SU-C-BRD-03: Analysis of Accelerator Generated Text Logs for Preemptive Maintenance

    SciTech Connect (OSTI)

    Able, CM; Baydush, AH; Nguyen, C; Munley, MT; Gersh, J; Ndlovu, A; Rebo, I; Booth, J; Perez, M; Sintay, B

    2014-06-15

    Purpose: To develop a model to analyze medical accelerator generated parameter and performance data that will provide an early warning of performance degradation and impending component failure. Methods: A robust 6 MV VMAT quality assurance treatment delivery was used to test the constancy of accelerator performance. The generated text log files were decoded and analyzed using statistical process control (SPC) methodology. The text file data is a single snapshot of energy specific and overall systems parameters. A total of 36 system parameters were monitored which include RF generation, electron gun control, energy control, beam uniformity control, DC voltage generation, and cooling systems. The parameters were analyzed using Individual and Moving Range (I/MR) charts. The chart limits were calculated using a hybrid technique that included the use of the standard 3? limits and the parameter/system specification. Synthetic errors/changes were introduced to determine the initial effectiveness of I/MR charts in detecting relevant changes in operating parameters. The magnitude of the synthetic errors/changes was based on: the value of 1 standard deviation from the mean operating parameter of 483 TB systems, a small fraction (? 5%) of the operating range, or a fraction of the minor fault deviation. Results: There were 34 parameters in which synthetic errors were introduced. There were 2 parameters (radial position steering coil, and positive 24V DC) in which the errors did not exceed the limit of the I/MR chart. The I chart limit was exceeded for all of the remaining parameters (94.2%). The MR chart limit was exceeded in 29 of the 32 parameters (85.3%) in which the I chart limit was exceeded. Conclusion: Statistical process control I/MR evaluation of text log file parameters may be effective in providing an early warning of performance degradation or component failure for digital medical accelerator systems. Research is Supported by Varian Medical Systems, Inc.

  10. Spontaneous Potential Well Log | Open Energy Information

    Open Energy Info (EERE)

    Log Chemical Logging Density Log Gamma Log Image Logs Mud Logging Neutron Log Pressure Temperature Log Single-Well and Cross-Well Resistivity Spontaneous Potential Well Log...

  11. Log Summarization

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ... analysis 22, financial time series prediction 23, and biological data sampling 24. ... Kelly 34 proposes how to use queuing theory observations to distinguish performance ...

  12. Chemical Logging At North Brawley Geothermal Area (Department...

    Open Energy Info (EERE)

    Chemical logs were made from well fluids for analysis when designing the first experimental power plant Notes Detailed logs of well fluids were recorded. Non-condensable gases...

  13. Log analysis of six boreholes in conjunction with geologic characterization above and on top of the Weeks Island salt dome

    SciTech Connect (OSTI)

    Sattler, A.R.

    1996-04-01

    Six boreholes were drilled during the geologic characterization and diagnostics of the Weeks Island sinkhole that is over the two-tiered salt mine which was converted for oil storage by the US Strategic Petroleum Reserve. These holes were drilled to provide for geologic characterization of the Weeks Island Salt Dome and its overburden in the immediate vicinity of the sinkhole (mainly through logs and core); to establish a crosswell configuration for seismic tomography; to establish locations for hydrocarbon detection and tracer injection; and to Provide direct observations of sinkhole geometry and material properties. Specific objectives of the logging program were to: (1) identify the top of and the physical state of the salt dome; (2) identify the water table; (3) obtain a relative salinity profile in the aquifer within the alluvium, which ranges from the water table directly to the top of the Weeks Island salt dome; and (4) identify a reflecting horizon seen on seismic profiles over this salt dome. Natural gamma, neutron, density, sonic, resistivity and caliper logs were run. Neutron and density logs were run from inside the well casing because of the extremely unstable condition of the deltaic alluvium overburden above the salt dome. The logging program provided important information about the salt dome and the overburden in that (1) the top of the salt dome was identified at {approximately}189 ft bgl (103 ft msl), and the top of the dome contains relatively few fractures; (2) the water table is approximately 1 ft msl, (3) this aquifer appears to become steadily more saline with depth; and (4) the water saturation of much of the alluvium over the salt dome is shown to be influenced by the prevalent heavy rainfall. This logging program, a part of the sinkhole diagnostics, provides unique information about this salt dome and the overburden.

  14. Log analysis of six boreholes in conjunction with geologic characterization above and on top of the Weeks Island Salt Dome

    SciTech Connect (OSTI)

    Sattler, A.R.

    1996-06-01

    Six boreholes were drilled during the geologic characterization and diagnostics of the Weeks Island sinkhole that is over the two-tiered salt mine which was converted for oil storage by the U.S. Strategic Petroleum Reserve. These holes were drilled to provide for geologic characterization of the Weeks Island Salt Dome and its overburden in the immediate vicinity of the sinkhole (mainly through logs and core); to establish a crosswell configuration for seismic tomography; to establish locations for hydrocarbon detection and tracer injection; and to provide direct observations of sinkhole geometry and material properties. Specific objectives of the logging program were to: (1) identify the top of and the physical state of the salt dome; (2) identify the water table; (3) obtain a relative salinity profile in the aquifer within the alluvium, which ranges from the water table directly to the top of the Weeks Island salt dome; and (4) identify a reflecting horizon seen on seismic profiles over this salt dome. Natural gamma, neutron, density, sonic, resistivity and caliper logs were run.

  15. Well Log ETL tool

    Energy Science and Technology Software Center (OSTI)

    2013-08-01

    This is an executable python script which offers two different conversions for well log data: 1) Conversion from a BoreholeLASLogData.xls model to a LAS version 2.0 formatted XML file. 2) Conversion from a LAS 2.0 formatted XML file to an entry in the WellLog Content Model. Example templates for BoreholeLASLogData.xls and WellLogsTemplate.xls can be found in the package after download.

  16. Caliper Log | Open Energy Information

    Open Energy Info (EERE)

    Information Exploration Group: Downhole Techniques Exploration Sub Group: Well Log Techniques Parent Exploration Technique: Well Log Techniques Information Provided by...

  17. Log-Tool

    Energy Science and Technology Software Center (OSTI)

    2012-05-21

    Log files are typically semi- or un-structured. To be useable for visualization and machine learning, they need to be parsed into a standard, structured format. Log-tool is a tool for facilitating the parsing, structuring, and routing of log files (e.g. intrusion detection long, web server logs, system logs). It consists of three main components: (1) Input – it will input data from files, standard input, and syslog, (2) Parser – it will parse the logmore »file based on regular expressions into structured data (JSNO format), (3) Output – it will output structured data into commonly used formats, including Redis (a database), standard output, and syslog.« less

  18. Logging in to Franklin

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Logging in Logging in to Franklin Interactive Access You can log in to Franklin using SSH (Secure Shell) with the following command from any UNIX, Linux, FreeBSD, etc. command shell or terminal: % ssh -l username franklin.nersc.gov There are a number of SSH-capable clients available for Windows, Mac, and UNIX/Linux machines. NERSC does not support or recommend any particular client. Franklin has 10 login nodes; you will be randomly connected to one of those 10 when you ssh to franklin.nersc.gov.

  19. Acoustic Logs | Open Energy Information

    Open Energy Info (EERE)

    different types of acoustic logs are used, based on the frequencies used, the way the signal is recorded, and the purpose of the log. All these logs require fluid in the well to...

  20. Density Log | Open Energy Information

    Open Energy Info (EERE)

    Density Log Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Technique: Density Log Details Activities (7) Areas (6) Regions (0) NEPA(0) Exploration...

  1. NMR logging apparatus

    DOE Patents [OSTI]

    Walsh, David O; Turner, Peter

    2014-05-27

    Technologies including NMR logging apparatus and methods are disclosed. Example NMR logging apparatus may include surface instrumentation and one or more downhole probes configured to fit within an earth borehole. The surface instrumentation may comprise a power amplifier, which may be coupled to the downhole probes via one or more transmission lines, and a controller configured to cause the power amplifier to generate a NMR activating pulse or sequence of pulses. Impedance matching means may be configured to match an output impedance of the power amplifier through a transmission line to a load impedance of a downhole probe. Methods may include deploying the various elements of disclosed NMR logging apparatus and using the apparatus to perform NMR measurements.

  2. Logs Perl Module

    Energy Science and Technology Software Center (OSTI)

    2007-04-04

    A perl module designed to read and parse the voluminous set of event or accounting log files produced by a Portable Batch System (PBS) server. This module can filter on date-time and/or record type. The data can be returned in a variety of formats.

  3. Log in | The Ames Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Error message Access denied. You must log in to view this page.

  4. Logging-while-coring method and apparatus

    DOE Patents [OSTI]

    Goldberg, David S.; Myers, Gregory J.

    2007-01-30

    A method and apparatus for downhole coring while receiving logging-while-drilling tool data. The apparatus includes core collar and a retrievable core barrel. The retrievable core barrel receives core from a borehole which is sent to the surface for analysis via wireline and latching tool The core collar includes logging-while-drilling tools for the simultaneous measurement of formation properties during the core excavation process. Examples of logging-while-drilling tools include nuclear sensors, resistivity sensors, gamma ray sensors, and bit resistivity sensors. The disclosed method allows for precise core-log depth calibration and core orientation within a single borehole, and without at pipe trip, providing both time saving and unique scientific advantages.

  5. Logging-while-coring method and apparatus

    DOE Patents [OSTI]

    Goldberg, David S. (New York, NY); Myers, Gregory J. (Cornwall, NY)

    2007-11-13

    A method and apparatus for downhole coring while receiving logging-while-drilling tool data. The apparatus includes core collar and a retrievable core barrel. The retrievable core barrel receives core from a borehole which is sent to the surface for analysis via wireline and latching tool The core collar includes logging-while-drilling tools for the simultaneous measurement of formation properties during the core excavation process. Examples of logging-while-drilling tools include nuclear sensors, resistivity sensors, gamma ray sensors, and bit resistivity sensors. The disclosed method allows for precise core-log depth calibration and core orientation within a single borehole, and without at pipe trip, providing both time saving and unique scientific advantages.

  6. Neutron Log | Open Energy Information

    Open Energy Info (EERE)

    Dictionary.png Neutron Log: The neutron log responds primarily to the amount of hydrogen in the formation which is contained in oil, natural gas, and water. The amount of...

  7. Geotech Logging Services | Open Energy Information

    Open Energy Info (EERE)

    Logging Services Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: Geotech Logging Services Author Geotech Logging Servces LLC Published Publisher...

  8. Category:Chemical Logging | Open Energy Information

    Open Energy Info (EERE)

    Chemical Logging Jump to: navigation, search Geothermalpower.jpg Looking for the Chemical Logging page? For detailed information on Chemical Logging, click here. Category:Chemical...

  9. Coiled-tubing logging system

    SciTech Connect (OSTI)

    Howell, E.P.; Smith, L.J.; Blount, C.G.

    1988-03-01

    Techniques have been developed to use coiled tubing containing a seven-conductor wireline to facilitate logging operations. Equipment has been designed to permit the connection of conventional logging tools to the tubing and the recording of logs. Operating techniques have been developed and applied under various wellbore conditions. The system allows traditional log measurements in a well while wellbore conditions are controlled. Advantages of the system include reduced wellbore pressure during peroration to maximize perforation performance; lubrication during pulling or pushing a logging tool through a borehole so that a more uniform velocity can be maintained with a logging sonde; continued circulation and thus borehole stability during logging; temperature reduction for improved reliability of logging sonde electronics in hot holes; and more stable positioning of perforation equipment. The ability of coiled tubing to push tools down highly deviated or horizontal wellbores makes logging or perforating feasible in these wells. Expenses can often be reduced with coiled-tubing logging because a rig is unnecessary during many operations.

  10. Coiled-tubing logging system

    SciTech Connect (OSTI)

    Howell, E.P.; Smith, L.J.; Blount, C.G.

    1986-01-01

    Techniques have been developed which use coiled tubing containing a seven-conductor wireline to facilitate logging operations. Equipment has been designed which permits the connection of conventional logging tools to the tubing and the recording of logs. Also, operating techniques have been developed and applied under various wellbore conditions. The system allows traditional log measurements in a well while controlling wellbore conditions. Advantages of the system include: reduced wellbore pressure during perforation to minimize formation damage: lubrication while pulling or pushing a logging tool through a borehole so that a more uniform velocity can be maintained with a logging sonde; continued circulation and thus borehole stability while logging; temperature reduction for improved reliability of logging sonde electronics in hot holes; and more stable positioning of perforation equipment. The ability of coiled tubing to push tools down highly deviated, or even horizontal wellbores, makes logging or perforating feasible in these wells. Expenses can often be reduced with coiled-tubing logging, since a rig is unnecessary during many operations.

  11. Acoustic paramagnetic logging tool

    DOE Patents [OSTI]

    Vail, III, William B. (Bothell, WA)

    1988-01-01

    New methods and apparatus are disclosed which allow measurement of the presence of oil and water in geological formations using a new physical effect called the Acoustic Paramagnetic Logging Effect (APLE). The presence of petroleum in formation causes a slight increase in the earth's magnetic field in the vicinity of the reservoir. This is the phenomena of paramagnetism. Application of an acoustic source to a geological formation at the Larmor frequency of the nucleons present causes the paramagnetism of the formation to disappear. This results in a decrease in the earth3 s magnetic field in the vicinity of the oil bearing formation. Repetitively frequency sweeping the acoustic source through the Larmor frequency of the nucleons present (approx. 2 kHz) causes an amplitude modulation of the earth's magnetic field which is a consequence of the APLE. The amplitude modulation of the earth's magnetic field is measured with an induction coil gradiometer and provides a direct measure of the amount of oil and water in the excitation zone of the formation . The phase of the signal is used to infer the longitudinal relaxation times of the fluids present, which results in the ability in general to separate oil and water and to measure the viscosity of the oil present. Such measurements may be preformed in open boreholes and in cased well bores.

  12. Chemical Logging | Open Energy Information

    Open Energy Info (EERE)

    concentrations.1 Use in Geothermal Exploration During a chemical logging study at the Raft River Geothermal Test Site, returned drilling fluid samples were collected every...

  13. Category:Neutron Log | Open Energy Information

    Open Energy Info (EERE)

    Looking for the Neutron Log page? For detailed information on Neutron Log, click here. Category:Neutron Log Add.png Add a new Neutron Log Technique Pages in category...

  14. A new approach for deriving pseudovelocity logs from resistivity logs

    SciTech Connect (OSTI)

    Dos Santos, W.L.B.; Ulrych, T.J.; De Lima, O.A.L.

    1988-01-01

    This paper describes a method of generating pseudovelocity logs using measurements of electrical resistivity. A theoretical relation between electrical resistivity and transit time, which is applicable to a wide range of lithologies, has been developed. The application of this relation using a method which defines lithoresistivity zones as lithological intervals related to the same formation and showing small resistivity variations, has been tested in the Reconcavo sedimentary basin in Bahia, Brazil. A comparison of derived pseudovelocity logs with actual sonic logs for five wells shows the validity of the present approach.

  15. Category:Well Log Techniques | Open Energy Information

    Open Energy Info (EERE)

    1 pages C Caliper Log 1 pages Chemical Logging 1 pages D Density Log 1 pages G Gamma Log 1 pages I Image Logs 1 pages M Mud...

  16. Vertical Flowmeter Logging | Open Energy Information

    Open Energy Info (EERE)

    Logging Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: Vertical Flowmeter Logging Author U.S. Geological Survey Published USGS Groundwater...

  17. Well Log Techniques | Open Energy Information

    Open Energy Info (EERE)

    formation properties versus depth in a borehole. Other definitions:Wikipedia Reegle Introduction Well logging, also known as wireline logging, is a method of data collection in the...

  18. Well Log Techniques At Raft River Geothermal Area (1977) | Open...

    Open Energy Info (EERE)

    the rock using well log data. Notes Information is given on the following logs: dual-induction focused log, including resistivity, sp, and conductivity; acoustic log; compensated...

  19. Chemical logging of geothermal wells

    DOE Patents [OSTI]

    Allen, Charles A. (Idaho Falls, ID); McAtee, Richard E. (Idaho Falls, ID)

    1981-01-01

    The presence of geothermal aquifers can be detected while drilling in geothermal formations by maintaining a chemical log of the ratio of the concentrations of calcium to carbonate and bicarbonate ions in the return drilling fluid. A continuous increase in the ratio of the concentrations of calcium to carbonate and bicarbonate ions is indicative of the existence of a warm or hot geothermal aquifer at some increased depth.

  20. Borehole Geophysical Logging | Open Energy Information

    Open Energy Info (EERE)

    Logging Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: Borehole Geophysical Logging Authors Hager-Richter Geoscience and Inc. Published Publisher Not...

  1. Energy Citations Database (ECD) - Alerts Log On

    Office of Scientific and Technical Information (OSTI)

    Log On You must Log On to use the ECD Alerts. Alerts provide users with e-mail notification of updates to the ECD in specific areas of interest. If you wish to receive an Alert and...

  2. Leak checker data logging system

    DOE Patents [OSTI]

    Gannon, J.C.; Payne, J.J.

    1996-09-03

    A portable, high speed, computer-based data logging system for field testing systems or components located some distance apart employs a plurality of spaced mass spectrometers and is particularly adapted for monitoring the vacuum integrity of a long string of a superconducting magnets such as used in high energy particle accelerators. The system provides precise tracking of a gas such as helium through the magnet string when the helium is released into the vacuum by monitoring the spaced mass spectrometers allowing for control, display and storage of various parameters involved with leak detection and localization. A system user can observe the flow of helium through the magnet string on a real-time basis hour the exact moment of opening of the helium input valve. Graph reading can be normalized to compensate for magnet sections that deplete vacuum faster than other sections between testing to permit repetitive testing of vacuum integrity in reduced time. 18 figs.

  3. Leak checker data logging system

    DOE Patents [OSTI]

    Gannon, Jeffrey C. (Arlington, TX); Payne, John J. (Waterman, IL)

    1996-01-01

    A portable, high speed, computer-based data logging system for field testing systems or components located some distance apart employs a plurality of spaced mass spectrometers and is particularly adapted for monitoring the vacuum integrity of a long string of a superconducting magnets such as used in high energy particle accelerators. The system provides precise tracking of a gas such as helium through the magnet string when the helium is released into the vacuum by monitoring the spaced mass spectrometers allowing for control, display and storage of various parameters involved with leak detection and localization. A system user can observe the flow of helium through the magnet string on a real-time basis hour the exact moment of opening of the helium input valve. Graph reading can be normalized to compensate for magnet sections that deplete vacuum faster than other sections between testing to permit repetitive testing of vacuum integrity in reduced time.

  4. Technical evaluation of software for gamma-ray logging system

    SciTech Connect (OSTI)

    Stromswold, D.C.

    1994-05-01

    This report contains results of a technical review of software, identified as LGCALC, that processes data collected by a high-resolution gamma-ray borehole logging system. The software presently operates within Westinghouse Hanford Company, Department of Geosciences, to process data collected by the Radionuclide Logging System. The software has been reviewed for its suitability for processing data to be collected by new high-resolution gamma-ray logging trucks scheduled to begin operational tests within Westinghouse Tank Waste Remediation Systems during 1994. Examination of the program code and hands-on operational tests have shown that this software is suitable for its intended use of processing high-resolution gamma-ray data obtained from borehole logging. Most of the code requires no changes, but in a few limited cases, suggestions have been made to correct errors or improve operation. Section 4 describes these changes. The technical review has confirmed the appropriateness, correctness, completeness, and coding accuracy of algorithms used to process spectral gamma-ray data, leading to a calculation of subsurface radionuclide contaminants. Running the program with test data from calibration models has confirmed that the program operates correctly. Comparisons with hand calculations have shown the correctness of the output from the program, based on known input data. Section 3 describes these tests. The recommended action is to make the near term programming changes suggested in Section 4.1 and then use the LGCALC analysis program with the new high-resolution logging systems once they have been properly calibrated.

  5. Image Logs | Open Energy Information

    Open Energy Info (EERE)

    StratigraphicStructural: -Fault and fracture identification -Rock texture, porosity, and stress analysis -determine dip, thickness, and geometry of rock strata in vicinity of...

  6. Logging in to Cori P1

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Logging in Logging in to Cori P1 Interactive Access You can log in to Cori using SSH (Secure Shell) with the following command from any UNIX, Mac OS X, Linux, FreeBSD, etc. command shell or terminal: ssh -l username cori.nersc.gov There are several SSH-capable clients available for Windows, Mac, and UNIX/Linux machines. NERSC does not support or recommend any particular client. More information on connecting to NERSC with SSH, including how to generate SSH keys for passworless logins, can be

  7. Logs Wood Chips Straw Corn Switchgrass

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    in wind can make electricity. Bioenergy comes from plants we can turn into fuel. Logs Wood Chips Straw Corn Switchgrass We can use energy from the earth to heat and cool our...

  8. Formation mechanical properties and the sonic log

    SciTech Connect (OSTI)

    Elphick, R.Y.

    1988-11-01

    A program is presented that calculates the mechanical properties of reservoir rocks from sonic logs. The program was written in Microsoft BASIC and the source code for MS-DOS, Apple Macintosh, and Amiga personal computers is given.

  9. CMLOG: A common message logging system

    SciTech Connect (OSTI)

    Chen, J.; Akers, W.; Bickley, M.; Wu, D.; Watson, W. III

    1997-12-01

    The Common Message Logging (CMLOG) system is an object-oriented and distributed system that not only allows applications and systems to log data (messages) of any type into a centralized database but also lets applications view incoming messages in real-time or retrieve stored data from the database according to selection rules. It consists of a concurrent Unix server that handles incoming logging or searching messages, a Motif browser that can view incoming messages in real-time or display stored data in the database, a client daemon that buffers and sends logging messages to the server, and libraries that can be used by applications to send data to or retrieve data from the database via the server. This paper presents the design and implementation of the CMLOG system meanwhile it will also address the issue of integration of CMLOG into existing control systems.

  10. Energy Citations Database (ECD) - Alerts Log On

    Office of Scientific and Technical Information (OSTI)

    ECD Alerts Log On Alerts provide users with e-mail notification of updates to the ECD in specific areas of interest. If you wish to receive an Alert and are not registered, please...

  11. Cement Bond Log | Open Energy Information

    Open Energy Info (EERE)

    casing and cement and between cement and borehole wall. Most cement-bond logs are a measurement only of the amplitude of the early arriving casing signal. Although a small...

  12. Category:Cross-Dipole Acoustic Log | Open Energy Information

    Open Energy Info (EERE)

    Cross-Dipole Acoustic Log Jump to: navigation, search Geothermalpower.jpg Looking for the Cross-Dipole Acoustic Log page? For detailed information on Cross-Dipole Acoustic Log,...

  13. Property:FirstWellLog | Open Energy Information

    Open Energy Info (EERE)

    FirstWellLog Jump to: navigation, search Property Name FirstWellLog Property Type Page Retrieved from "http:en.openei.orgwindex.php?titleProperty:FirstWellLog&oldid598766...

  14. Category:Pressure Temperature Log | Open Energy Information

    Open Energy Info (EERE)

    Geothermalpower.jpg Looking for the Pressure Temperature Log page? For detailed information on Pressure Temperature Log, click here. Category:Pressure Temperature Log Add.png Add a...

  15. Gamma-Ray Logging Workshop (February 1981) | Department of Energy

    Office of Environmental Management (EM)

    Gamma-Ray Logging Workshop (February 1981) Gamma-Ray Logging Workshop (February 1981) Gamma-Ray Logging Workshop (February 1981) PDF icon Gamma-Ray Logging Workshop (February 1981) More Documents & Publications Borehole Logging Methods for Exploration and Evaluation of Uranium Deposits (1967) Grade Assignments for Models Used for Calibration of Gross-Count Gamma-Ray Logging Systems (December 1983) Parameter Assignments for Spectral Gamma-Ray Borehole Calibration Models (April 1984)

  16. Green Energy Resources Inc formerly New York International Log...

    Open Energy Info (EERE)

    Inc formerly New York International Log Lumber Company Jump to: navigation, search Name: Green Energy Resources Inc (formerly New York International Log & Lumber Company) Place:...

  17. Energy Efficiency in Log Homes | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    energy efficiency when designing or purchasing a log home. | Photo courtesy of iStockphoto.comtinabelle Consider energy efficiency when designing or purchasing a log home. |...

  18. Method for determining formation quality factor from well log...

    Office of Scientific and Technical Information (OSTI)

    well log data and its application to seismic reservoir characterization Citation Details In-Document Search Title: Method for determining formation quality factor from well log ...

  19. COMPARISON OF ACOUSTIC AND ELECTRICAL IMAGE LOGS FROM THE COSO...

    Open Energy Info (EERE)

    image log, but locally approach 100%. This fabric is unlikely to contribute to permeability in the reservoir. Acoustic image logs reveal a similar natural fracture population,...

  20. Pressure Temperature Log At Vale Hot Springs Area (Combs, Et...

    Open Energy Info (EERE)

    Unknown Notes Numerous temperature logs were taken with Sandia's platinum-resistance-thermometer (PRT) tool which along with a Sandia logging truck remained on-site for...

  1. Logjam: A scalable unified log file archiver

    Energy Science and Technology Software Center (OSTI)

    2001-08-01

    Log files are a necessary record of events on any system. However, as systems scale, so does the volume of data captured. To complicate matters, this data can be distributed across all nodes within the system. This creates challenges in ways to obtain these files as well as archiving them in a consistent manner. It has become commonplace to develop a custom written utility for each system that is tailored specifically to that system. Formore » computer centers that contain multiple systems, each system would have their own respective utility for gathering and archiving log files. Each time a new log file is produced, a modification to the utility is necessary. With each modification, risks of errors could be introduced as well as spending time to introduce that change. This is precisely the purpose of logjam. Once installed, the code only requires modification when new features are required. A configuration file is used to identify each log file as well as where to harvest it and how to archive it. Adding a new log file is as simple as defining it in a configuration file and testing can be performed in the production environment.« less

  2. Development of pulsed neutron uranium logging instrument

    SciTech Connect (OSTI)

    Wang, Xin-guang; Liu, Dan; Zhang, Feng

    2015-03-15

    This article introduces a development of pulsed neutron uranium logging instrument. By analyzing the temporal distribution of epithermal neutrons generated from the thermal fission of {sup 235}U, we propose a new method with a uranium-bearing index to calculate the uranium content in the formation. An instrument employing a D-T neutron generator and two epithermal neutron detectors has been developed. The logging response is studied using Monte Carlo simulation and experiments in calibration wells. The simulation and experimental results show that the uranium-bearing index is linearly correlated with the uranium content, and the porosity and thermal neutron lifetime of the formation can be acquired simultaneously.

  3. Logging of subterranean wells using coiled tubing

    SciTech Connect (OSTI)

    Pilla, J.

    1991-01-15

    This patent describes an apparatus for production logging of a well utilizing artificial lift in a wellbore. It comprises: coiled tubing extending into the wellbore having wireline electrical cable passing through a central bore thereof and having a remote end within the wellbore which end is connected to gas injector means. The wireline cable passing through the gas injector means to a flexible electrically conductive support spacer having an end portion remote from the gas injector means and logging means connected to the end portion of the support spacer.

  4. Borehole Logging Methods for Exploration and Evaluation of Uranium Deposits

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    (1967) | Department of Energy Borehole Logging Methods for Exploration and Evaluation of Uranium Deposits (1967) Borehole Logging Methods for Exploration and Evaluation of Uranium Deposits (1967) Borehole Logging Methods for Exploration and Evaluation of Uranium Deposits (1967) PDF icon Borehole Logging Methods for Exploration and Evaluation of Uranium Deposits (1967) More Documents & Publications Gamma-Ray Logging Workshop (February 1981) Grade Assignments for Models Used for

  5. Logging Calibration Models for Fission Neutron Sondes (September 1981) |

    Office of Environmental Management (EM)

    Department of Energy Logging Calibration Models for Fission Neutron Sondes (September 1981) Logging Calibration Models for Fission Neutron Sondes (September 1981) Logging Calibration Models for Fission Neutron Sondes (September 1981) PDF icon Logging Calibration Models for Fission Neutron Sondes (September 1981) More Documents & Publications A Model for Water Factor Measurements With Fission-Neutron Logging Tools (May 1983) Field Calibration Facilities for Environmental Measurement of

  6. Energy Efficiency in Log Homes | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Design » Types of Homes » Energy Efficiency in Log Homes Energy Efficiency in Log Homes Consider energy efficiency when designing or purchasing a log home. | Photo courtesy of ©iStockphoto.com/tinabelle Consider energy efficiency when designing or purchasing a log home. | Photo courtesy of ©iStockphoto.com/tinabelle Log homes may be site-built or pre-cut in a factory for delivery to the site. Some log home manufacturers can also customize their designs. Before designing or purchasing a

  7. Formation Micro-Imager Logs (FMI) | Open Energy Information

    Open Energy Info (EERE)

    Logs (FMI) Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: Formation Micro-Imager Logs (FMI) Author Shakeel Ahmed Published Publisher Not...

  8. Geophysical logging case history of the Raft River geothermal...

    Open Energy Info (EERE)

    logging case history of the Raft River geothermal system, Idaho Jump to: navigation, search OpenEI Reference LibraryAdd to library Report: Geophysical logging case history of the...

  9. Log amplifier with pole-zero compensation

    DOE Patents [OSTI]

    Brookshier, William

    1987-01-01

    A logarithmic amplifier circuit provides pole-zero compensation for improved stability and response time over 6-8 decades of input signal frequency. The amplifier circuit includes a first operational amplifier with a first feedback loop which includes a second, inverting operational amplifier in a second feedback loop. The compensated output signal is provided by the second operational amplifier with the log elements, i.e., resistors, and the compensating capacitors in each of the feedback loops having equal values so that each break point or pole is offset by a compensating break point or zero.

  10. Microsoft Word - FOIA Log FY 2001.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    1 FOIA - Request Log 1 Closed/ Date No. Dated Date Rec'd HQ or Dir. Subject Yes/ 3/29/01 001 02/01/01 02/01/01 01-0021C Transfer AL Copies of all documents including studies and memoranda, which may identify or consider WIPP site in Carlsbad, NM as a potential site for storage or disposal of spent reactor fuel or high-level radioactive wastes 2. All documents including studies, memoranda, hypothesizing, considering, recommending, or suggesting the WIPP site in NM as an alternative site to the

  11. Microsoft Word - FOIA Log FY 2002.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    2 FOIA - Request Log 1 Closed/ Date No. Dated Date Rec'd HQ or Dir. Subject Yes/ 1/30/02 001 12/3/02 12/21/02 Richland Transfer Richland Operation Office search for records they located documents originated by the DOE Carlsbad Field Office that may be responsive to Mr. Hongs request. By transfer of this letter they forwarded Mr. Hong request, along with the documents located at Richland to the Carlsbad FOIA Office. CBFO will respond directly to Mr. Hong with a release determination Yes/ 2/13/02

  12. Microsoft Word - FOIA Log FY 2004.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 FOIA - Request Log 1 Closed/ Date No. Dated Date Rec'd HQ or Dir. Subject Yes 02/20/04 001 02/02/04 02/02/04 Direct Copies of my personnel records that are maintained at 401 N. Canal Street in Carlsbad, New Mexico Yes 03/29/04 002 03/24/04 03/29/04 Direct Transferred to HQ Asking for information regarding Gary K. King during DOE Secretary Bill Richardson's administration from 08//18/1998 through 02/20/2001, including: 1. Travel vouchers and official expenditures made by the United States

  13. Microsoft Word - FOIA Log FY 2007.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    7 FOIA - Request Log 1 Closed/ Date No. Dated Date Rec'd HQ or Dir. Subject Finalized 02/08/07 001 10/05/06 01/08/07 Transfer from DOE- EM-CBC Copies of contract modifications, performance evaluations, task orders and task order proposals related to contract AT30-05EW03000 with Navarro Research and Engineering, Inc. Finalized 01/31/07 002 01/11/07 01/11/07 Direct For a copy of contract DE-AC04-95AL89446 for the period of September 1995 through the end of the contract. Also, if not included in

  14. Log amplifier with pole-zero compensation

    DOE Patents [OSTI]

    Brookshier, W.

    1985-02-08

    A logarithmic amplifier circuit provides pole-zero compensation for improved stability and response time over 6-8 decades of input signal frequency. The amplifer circuit includes a first operational amplifier with a first feedback loop which includes a second, inverting operational amplifier in a second feedstock loop. The compensated output signal is provided by the second operational amplifier with the log elements, i.e., resistors, and the compensating capacitors in each of the feedback loops having equal values so that each break point is offset by a compensating break point or zero.

  15. Manager's Signature Log Privacy Impact Assessment, Office of Science

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Chicago Office | Department of Energy Manager's Signature Log Privacy Impact Assessment, Office of Science Chicago Office Manager's Signature Log Privacy Impact Assessment, Office of Science Chicago Office Manager's Signature Log Privacy Impact Assessment, Office of Science Chicago Office PDF icon Manager's Signature Log Privacy Impact Assessment, Office of Science Chicago Office More Documents & Publications Integrated Safety Management Workshop Registration, PIA, Idaho National

  16. Well Logging Security Initiatives | Y-12 National Security Complex

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Well Logging Security ... Well Logging Security Initiatives The mp4 video format is not supported by this browser. Download video Captions: On Watch as GTRI demonstrates the threat to the security of (oil) well logging systems and outlines the initiatives that are enhancing the security of these sources worldwide

  17. Dual excitation acoustic paramagnetic logging tool

    DOE Patents [OSTI]

    Vail, W.B. III.

    1989-02-14

    New methods and apparatus are disclosed which allow measurement of the presence of oil and water in geological formations using a new physical effect called the Acoustic Paramagnetic Logging Effect (APLE). The presence of petroleum in formation causes a slight increase in the earth's magnetic field in the vicinity of the reservoir. This is the phenomena of paramagnetism. Application of an acoustic source to a geological formation at the Larmor frequency of the nucleons present causes the paramagnetism of the formation to disappear. This results in a decrease in the earth's magnetic field in the vicinity of the oil bearing formation. Repetitively frequency sweeping the acoustic source through the Larmor frequency of the nucleons present (approx. 2 kHz) causes an amplitude modulation of the earth's magnetic field which is a consequence of the APLE. The amplitude modulation of the earth's magnetic field is measured with an induction coil gradiometer and provides a direct measure of the amount of oil and water in the excitation zone of the formation. The phase of the signal is used to infer the longitudinal relaxation times of the fluids present, which results in the ability in general to separate oil and water and to measure the viscosity of the oil present. Such measurements may be performed in open boreholes and in cased well bores. The Dual Excitation Acoustic Paramagnetic Logging Tool employing two acoustic sources is also described. 6 figs.

  18. Dual excitation acoustic paramagnetic logging tool

    DOE Patents [OSTI]

    Vail, III, William B. (Bothell, WA)

    1989-01-01

    New methods and apparatus are disclosed which allow measurement of the presence of oil and water in gelogical formations using a new physical effect called the Acoustic Paramagnetic Logging Effect (APLE). The presence of petroleum in formation causes a slight increase in the earth's magnetic field in the vicinity of the reservoir. This is the phenomena of paramagnetism. Application of an acoustic source to a geological formation at the Larmor frequency of the nucleous present causes the paramagnetism of the formation to disappear. This results in a decrease in the earth's magnetic field in the vicinity of the oil bearing formation. Repetitively frequency sweeping the acoustic source through the Larmor frequency of the nucleons present (approx. 2 kHz) causes an amplitude modulation of the earth's magnetic field which is a consequence of the APLE. The amplitude modulation of the earth's magnetic field is measured with an induction coil gradiometer and provides a direct measure of the amount of oil and water in the excitation zone of the formation. The phase of the signal is used to infer the longitudinal relaxation times of the fluids present, which results in the ability in general to separate oil and water and to measure the viscosity of the oil present. Such measurements may be preformed in open boreholes and in cased well bores. The Dual Excitation Acoustic Paramagnetic Logging Tool employing two acoustic sources is also described.

  19. Microsoft Word - FOIA Log FY 2005.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    5 FOIA - Request Log 1 Closed/ Date No. Dated Date Rec'd HQ or Dir. Subject Yes 02/23/05 001 02/16/05 02/16/05 Direct Copies of the 2004 Modifications to the Westinghouse TRU Solutions contract (No. DE-AC- 04-01AL66444) for the management and operation of the Waste Isolation Pilot Plant. Yes 04/12/05 002 04/11/05 04/11/05 Direct Copies of the scope of work statement for the EE&G Oversight contract for the Waste Isolation Pilot Plant, dated 1999 or 2000 Yes 04/29/05 003 04/20/05 04/20/05

  20. Nuclear, multichannel-sonic, ultrasonic analyses for determination of degree of fracturing and alteration in a fast formation: The deep ocean crust

    SciTech Connect (OSTI)

    Anderson, R.N.; O'Malley, H.; Newmark, R.L.

    1984-01-01

    Multichannel, Full-Waveform Sonic Logs offer quantitative information on the response of the formation to propagating acoustic energy. When coupled with ultrasonic borehole imagery, these logs show clear evidence of fractures intersecting the wellbore. P-wave, S-wave, Stoneley and late arriving normal modal CODA all show energy and frequency changes across fracture zones. One critical ingredient missing from the sonic-ultrasonic cross-correlations to date, has been the ability to estimate the quantity of alteration material infilling fractures. A new nuclear analysis technique has been developed to extract a reliable estimate of the amount of clay infilling in highly fractured basalts from the oceanic crust.

  1. Evaluation of Emerging Technology for Geothermal Drilling and Logging

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Applications | Department of Energy Evaluation of Emerging Technology for Geothermal Drilling and Logging Applications Evaluation of Emerging Technology for Geothermal Drilling and Logging Applications Evaluation of Emerging Technology for Geothermal Drilling and Logging Applications presentation at the April 2013 peer review meeting held in Denver, Colorado. PDF icon sandia_evaluation_drilling_tech_peer2013.pdf More Documents & Publications Evaluation of Emerging Technology for

  2. Western tight gas sands advanced logging workshop proceedings

    SciTech Connect (OSTI)

    Jennings, J B; Carroll, Jr, H B

    1982-04-01

    An advanced logging research program is one major aspect of the Western Tight Sands Program. Purpose of this workshop is to help BETC define critical logging needs for tight gas sands and to allow free interchange of ideas on all aspects of the current logging research program. Sixteen papers and abstracts are included together with discussions. Separate abstracts have been prepared for the 12 papers. (DLC)

  3. Drag reduction in coal log pipelines

    SciTech Connect (OSTI)

    Marrero, T.R.; Liu, H.

    1996-12-31

    It is well-known that solutions of dissolved long-chain macromolecules produce lower friction or drag losses than with the solvent alone. In coal log pipeline (CLP), water is the conveying medium. Synthetic polymers such as poly(ethylene oxide) have been dissolved in water and tested for their extent of drag reduction as a function of concentration and other variables. Lab-scale experimental results for CLP indicate substantial drag reduction at low concentration levels of polymer. But, the macromolecules exhibit degradation under mechanical shear stresses. The large molecules break into smaller units. This degradation effect causes a loss of drag reduction. However, high levels of drag reduction can be maintained as follows: (1) by injecting polymer into the CLP at several locations along the pipeline, (2) by injecting polymer of different particle sizes, (3) by using more robust types of polymers, or (4) by using polymer-fiber mixtures. This report presents the value of drag-reducing agents in terms of pumping power net cost savings. In addition, this report outlines the environmental impact of drag reduction polymers, and end-of-pipeline water treatment processes. For an operating CLP, hundreds of miles in length, the use of poly(ethylene oxide) as a drag reducing agent provides significant pumping power cost savings at a minimal materials cost.

  4. Chemical Logging At Dixie Valley Geothermal Area (Los Alamos...

    Open Energy Info (EERE)

    Dixie Valley Geothermal Area (Los Alamos National Laboratory, NM, 2002) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Chemical Logging At Dixie...

  5. Energy Efficiency in Log Homes | Department of Energy

    Office of Environmental Management (EM)

    or purchasing a manufactured log home, you should consider several factors related to energy efficiency. The R-Value of Wood A material's thermal resistance or resistance to...

  6. Acoustic Logs At Coso Geothermal Area (2005) | Open Energy Information

    Open Energy Info (EERE)

    Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Acoustic Logs At Coso Geothermal Area (2005) Exploration Activity Details Location Coso...

  7. Image Logs At Coso Geothermal Area (2011) | Open Energy Information

    Open Energy Info (EERE)

    Date 2011 Usefulness useful DOE-funding Unknown Exploration Basis Determine crustul stress heterogeneity Notes Borehole induced structures in image logs of wells from the Coso...

  8. Pressure Temperature Log At Fish Lake Valley Area (DOE GTP) ...

    Open Energy Info (EERE)

    Fish Lake Valley Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Pressure Temperature Log At Fish Lake Valley Area (DOE GTP)...

  9. Density Log At Valles Caldera - Redondo Geothermal Area (Rowley...

    Open Energy Info (EERE)

    Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Density Log At Valles Caldera - Redondo Geothermal Area (Rowley, Et Al., 1987) Exploration...

  10. Density Log At Valles Caldera - Redondo Geothermal Area (Wilt...

    Open Energy Info (EERE)

    Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Density Log At Valles Caldera - Redondo Geothermal Area (Wilt & Haar, 1986) Exploration...

  11. Gamma Log At Coso Geothermal Area (1977) | Open Energy Information

    Open Energy Info (EERE)

    Coso Geothermal Area (1977) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Gamma Log At Coso Geothermal Area (1977) Exploration Activity Details...

  12. Acoustic Logs At Coso Geothermal Area (1977) | Open Energy Information

    Open Energy Info (EERE)

    1977) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Acoustic Logs At Coso Geothermal Area (1977) Exploration Activity Details Location Coso...

  13. Neutron Log At Coso Geothermal Area (1977) | Open Energy Information

    Open Energy Info (EERE)

    Coso Geothermal Area (1977) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Neutron Log At Coso Geothermal Area (1977) Exploration Activity...

  14. Selecting The Optimal Logging Suite For Geothermal Reservoir...

    Open Energy Info (EERE)

    and tensile wall fractures, and were adequate to detect stratigraphic features. Density, photo-electric factor (PEF), neutron, and gamma ray (GR) logs provided sufficient...

  15. Well Log Techniques At Newberry Caldera Area (DOE GTP) | Open...

    Open Energy Info (EERE)

    navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Well Log Techniques At Newberry Caldera Area (DOE GTP) Exploration Activity Details Location Newberry...

  16. Well Log Techniques At Coso Geothermal Area (1985) | Open Energy...

    Open Energy Info (EERE)

    navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Well Log Techniques At Coso Geothermal Area (1985) Exploration Activity Details Location Coso Geothermal...

  17. Pressure Temperature Log At Fort Bliss Area (DOE GTP) | Open...

    Open Energy Info (EERE)

    navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Pressure Temperature Log At Fort Bliss Area (DOE GTP) Exploration Activity Details Location Fort Bliss...

  18. Pressure Temperature Log At Silver Peak Area (DOE GTP) | Open...

    Open Energy Info (EERE)

    navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Pressure Temperature Log At Silver Peak Area (DOE GTP) Exploration Activity Details Location Silver Peak...

  19. Pressure Temperature Log At Flint Geothermal Area (DOE GTP) ...

    Open Energy Info (EERE)

    navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Pressure Temperature Log At Flint Geothermal Area (DOE GTP) Exploration Activity Details Location Flint...

  20. Pressure Temperature Log At Glass Buttes Area (DOE GTP) | Open...

    Open Energy Info (EERE)

    navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Pressure Temperature Log At Glass Buttes Area (DOE GTP) Exploration Activity Details Location Glass...

  1. Well Log Data At North Brawley Geothermal Area (Matlick & Jayne...

    Open Energy Info (EERE)

    to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Well Log Data At North Brawley Geothermal Area (Matlick & Jayne, 2008) Exploration Activity Details...

  2. Well Log Data At North Brawley Geothermal Area (Edmunds & W....

    Open Energy Info (EERE)

    to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Well Log Data At North Brawley Geothermal Area (Edmunds & W., 1977) Exploration Activity Details...

  3. Well Log Data At Blue Mountain Geothermal Area (Fairbank & Niggemann...

    Open Energy Info (EERE)

    to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Well Log Data At Blue Mountain Geothermal Area (Fairbank & Niggemann, 2004) Exploration Activity...

  4. Pressure Temperature Log At Colrado Area (DOE GTP) | Open Energy...

    Open Energy Info (EERE)

    Colrado Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Pressure Temperature Log At Colrado Area (DOE GTP) Exploration Activity...

  5. Pressure Temperature Log At Alum Area (DOE GTP) | Open Energy...

    Open Energy Info (EERE)

    Alum Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Pressure Temperature Log At Alum Area (DOE GTP) Exploration Activity Details...

  6. FMI Log At Maui Area (DOE GTP) | Open Energy Information

    Open Energy Info (EERE)

    Maui Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: FMI Log At Maui Area (DOE GTP) Exploration Activity Details Location Maui...

  7. Pressure Temperature Log At Mccoy Geothermal Area (DOE GTP) ...

    Open Energy Info (EERE)

    Mccoy Geothermal Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Pressure Temperature Log At Mccoy Geothermal Area (DOE GTP)...

  8. FMI Log At Wister Area (DOE GTP) | Open Energy Information

    Open Energy Info (EERE)

    Wister Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: FMI Log At Wister Area (DOE GTP) Exploration Activity Details Location...

  9. Pressure Temperature Log At Wister Area (DOE GTP) | Open Energy...

    Open Energy Info (EERE)

    Wister Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Pressure Temperature Log At Wister Area (DOE GTP) Exploration Activity...

  10. Pressure Temperature Log At Maui Area (DOE GTP) | Open Energy...

    Open Energy Info (EERE)

    Maui Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Pressure Temperature Log At Maui Area (DOE GTP) Exploration Activity Details...

  11. Acoustic Logs At Alum Area (Moos & Ronne, 2010) | Open Energy...

    Open Energy Info (EERE)

    tensile wall fractures, and were adequate to detect stratigraphic features. References Daniel Moos, Joel Ronne (2010) Selecting The Optimal Logging Suite For Geothermal Reservoir...

  12. Chemical logging- a geothermal technique | Open Energy Information

    Open Energy Info (EERE)

    technique Abstract Chemical logging studies conducted at the Department of Energy's Raft River Geothermal Test Site in south central Idaho resulted in the development of a...

  13. Chemical Logging At Raft River Geothermal Area (1979) | Open...

    Open Energy Info (EERE)

    Raft River Geothermal Area (1979) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Chemical Logging At Raft River Geothermal Area (1979)...

  14. Acoustic Logs At Raft River Geothermal Area (1979) | Open Energy...

    Open Energy Info (EERE)

    Raft River Geothermal Area (1979) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Acoustic Logs At Raft River Geothermal Area (1979) Exploration...

  15. Geothermal well log interpretation state of the art. Final report

    SciTech Connect (OSTI)

    Sanyal, S.K.; Wells, L.E.; Bickham, R.E.

    1980-01-01

    An in-depth study of the state of the art in Geothermal Well Log Interpretation has been made encompassing case histories, technical papers, computerized literature searches, and actual processing of geothermal wells from New Mexico, Idaho, and California. A classification scheme of geothermal reservoir types was defined which distinguishes fluid phase and temperature, lithology, geologic province, pore geometry, salinity, and fluid chemistry. Major deficiencies of Geothermal Well Log Interpretation are defined and discussed with recommendations of possible solutions or research for solutions. The Geothermal Well Log Interpretation study and report has concentrated primarily on Western US reservoirs. Geopressured geothermal reservoirs are not considered.

  16. Proceedings of the second PFN uranium logging seminar

    SciTech Connect (OSTI)

    Not Available

    1983-01-01

    The Prompt Fission Neutron (PFN) uranium logging system developed by Sandia National Laboratories for the US Department of Energy is described in some detail in papers by the staff that was involved in the final phase of the development project, and by others associated with the project as users of the logging probe or builders of some of the probe hardware. Descriptions are provided of the probe's electronic circuits, the uphole instrumentation, the log interpretation technique, field experience, neutron detection hardware, neutron generator design, life-test results, and observations by Bendix Field Engineering Corporation personnel regarding the use of the probe and its results.

  17. Image Logs At Coso Geothermal Area (2004) | Open Energy Information

    Open Energy Info (EERE)

    Coso Geothermal Region Notes During the second year of this project, wellbore logs and stress data were acquired in a new production well drilled in the Coso Geothermal Field,...

  18. Long Valley Caldera Field Trip Log | Open Energy Information

    Open Energy Info (EERE)

    to library Conference Paper: Long Valley Caldera Field Trip Log Abstract NA Authors Gene A. Suemnicht and Bastien Poux Conference NGA Long Valley Field Trip, July 5-7, 2012;...

  19. NMOCD - Form G-105 - Geothermal Resources Well Log | Open Energy...

    Open Energy Info (EERE)

    Jump to: navigation, search OpenEI Reference LibraryAdd to library General: NMOCD - Form G-105 - Geothermal Resources Well Log Author State of New Mexico Energy and Minerals...

  20. Efficiently log and perforate 60 + wells with coiled tubing

    SciTech Connect (OSTI)

    Fertl, W.H.; Hotz, R.F.

    1987-07-01

    In today's petroleum industry, more and more emphasis is being placed on logging and completion techniques for highly deviated (extended-reach) and horizontal boreholes. This is the result of cost-effective development of oil and gas via: a minimum number of production platforms on large structures, incremental but marginal reserves in outlying and/or small fault blocks, shallow reservoirs in deep offshore waters, and significant hydrocarbon accumulations in environmentally sensitive and/or restrictive areas, e.g., perma-frost, urban areas, etc. The major challenge in logging such high-angle, extended-reach, and also horizontal boreholes is guiding the logging tool string to the bottom of the wellbore. In the horizontal portion of a borehole, the use of coiled tubing has proven successful in ''pushing'' the logging instrumentation toward the bottom (end) of the borehole.

  1. JOBAID-LOGGING IN TO THE OLC LEARNING SYSTEM

    Broader source: Energy.gov [DOE]

    In this job aid you will Log In to the system, Retrieve Forgotten Password and/or User ID, and Use the LMS Help System built into the application.

  2. Fluid-Rock Characterization and Interactions in NMR Well Logging

    SciTech Connect (OSTI)

    Hirasaki, George J.; Mohanty, Kishore K.

    2003-02-10

    The objective of this project was to characterize the fluid properties and fluid-rock interactions that are needed for formation evaluation by NMR well logging. The advances made in the understanding of NMR fluid properties are summarized in a chapter written for an AAPG book on NMR well logging. This includes live oils, viscous oils, natural gas mixtures, and the relation between relaxation time and diffusivity.

  3. Fluid-Rock Characterization and Interactions in NMR Well Logging

    SciTech Connect (OSTI)

    Hirasaki, George J.; Mohanty, Kishore K.

    2003-02-10

    The objective of this project was to characterize the fluid properties and fluid-rock interactions which are needed for formation evaluation by NMR well logging. NMR well logging is finding wide use in formation evaluation. The formation parameters commonly estimated were porosity, permeability, and capillary bound water. Special cases include estimation of oil viscosity, residual oil saturation, location of oil/water contact, and interpretation on whether the hydrocarbon is oil or gas.

  4. Gamma Log At Alum Area (Moos & Ronne, 2010) | Open Energy Information

    Open Energy Info (EERE)

    Technique Gamma Log Activity Date Usefulness useful DOE-funding Unknown Notes Density, photo-electric factor (PEF), neutron, and gamma ray (GR) logs provided sufficient...

  5. Neutron Log At Alum Area (Moos & Ronne, 2010) | Open Energy Informatio...

    Open Energy Info (EERE)

    Technique Neutron Log Activity Date Usefulness useful DOE-funding Unknown Notes Density, photo-electric factor (PEF), neutron, and gamma ray (GR) logs provided sufficient...

  6. Logging with coiled tubing less effective than with drill pipe

    SciTech Connect (OSTI)

    Van Den Bosch, R. )

    1994-01-31

    Coiled tubing offered neither economic nor operational advantages over drill pipe for conveying logging tools in open hole shallow horizontal wells in Germany. In the past 2 years, Mobil Erdgas-Erdoel GMbH (MEEG) participated in completing eight shallow horizontal wells. These were medium-to-short radius wells at measured depths of between 850 and 2,000 m. The average horizontal section was 350 m. The logging tools were conveyed by coiled tubing or drill pipe. MEEG attempted to log five wells with coiled tubing-conveyed tools, four with 1 1/2-in. tubing. Total depth was reached reliably in only one well, the shallowest and with the shortest horizontal section. Simulation programs were unreliable for calculating the downhole forces of the coil/tool combination or predicting possible helical lockups. In wells with drill pipe-conveyed logs, the tool combination could always be pushed to total depth, and the operations were generally faster and cost less than logging with coiled tubing. Also, drill pipe allowed longer and heavier tool strings. For reliable operations, coiled tubing needs to be more rigid, rig-up/rig-down times need to be improved, and the simulation programs must be more reliable for predicting downhole lock-up.

  7. Appendix A Lithologic and Monitor Well Completion Logs

    Office of Legacy Management (LM)

    A Lithologic and Monitor Well Completion Logs This page intentionally left blank WELL INSTALLATION BLANK CASING: 1.25 in. Stainless Steel 0.0 to 0.35 METHOD WELL SCREEN: 1.25 in. Stainless Steel 0.35 to 3.27 DATE DEVELOPED SUMPIEND CAP: 1.25 in. Stainless Steel 3.27 to 3.58 WATER LEVEL (FT BGS) SURFACE SEAL: LOGGED BY P. McKenzie REMARKS Drillers hit water at 5 fl: well point removed. LITHOLOGIC DESCRIPTION LOCATION SHIPROCK, NM SURFACE ELEV. ( FT NGVD) 4890.00 SITE SHIPROCK TOP OF CASING (FT)

  8. Fluid-Rock Characterization and Interactions in NMR Well Logging

    SciTech Connect (OSTI)

    George J. Hirasaki; Kishore K. Mohanty

    2005-09-05

    The objective of this report is to characterize the fluid properties and fluid-rock interactions that are needed for formation evaluation by NMR well logging. The advances made in the understanding of NMR fluid properties are summarized in a chapter written for an AAPG book on NMR well logging. This includes live oils, viscous oils, natural gas mixtures, and the relation between relaxation time and diffusivity. Oil based drilling fluids can have an adverse effect on NMR well logging if it alters the wettability of the formation. The effect of various surfactants on wettability and surface relaxivity are evaluated for silica sand. The relation between the relaxation time and diffusivity distinguishes the response of brine, oil, and gas in a NMR well log. A new NMR pulse sequence in the presence of a field gradient and a new inversion technique enables the T{sub 2} and diffusivity distributions to be displayed as a two-dimensional map. The objectives of pore morphology and rock characterization are to identify vug connectivity by using X-ray CT scan, and to improve NMR permeability correlation. Improved estimation of permeability from NMR response is possible by using estimated tortuosity as a parameter to interpolate between two existing permeability models.

  9. Dual-cone double-helical downhole logging device

    DOE Patents [OSTI]

    Yu, Jiunn S. (Albuquerque, NM)

    1984-01-01

    A broadband downhole logging device includes a double-helix coil wrapped over a dielectric support and surrounded by a dielectric shield. The device may also include a second coil longitudinally aligned with a first coil and enclosed within the same shield for measuring magnetic permeability of downhole formations and six additional coils for accurately determining downhole parameters.

  10. NREL: National Residential Efficiency Measures Database - Change Log

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    History Change Log History Here you can view a list of changes to the National Residential Efficiency Measures Database. Version Date Description v3.0.0 3/21/13 Public Release v2.0.0 11/1/10 Public Release v1.0.0 2/26/10 Public Release v1.0.0Beta 2/18/10 DOE Lab Review

  11. Species characterization and responses of subcortical insects to trap-logs and ethanol in a hardwood biomass plantation: Subcortical insects in hardwood plantations

    SciTech Connect (OSTI)

    Coyle, David R.; Brissey, Courtney L.; Gandhi, Kamal J. K.

    2015-01-02

    1. We characterized subcortical insect assemblages in economically important eastern cottonwood (Populus deltoides Bartr.), sycamore (Platanus occidentalis L.) and sweetgum (Liquidambar styraciflua L.) plantations in the southeastern U.S.A. Furthermore, we compared insect responses between freshly-cut plant material by placing traps directly over cut hardwood logs (trap-logs), traps baited with ethanol lures and unbaited (control) traps. 2. We captured a total of 15 506 insects representing 127 species in four families in 2011 and 2013. Approximately 9% and 62% of total species and individuals, respectively, and 23% and 79% of total Scolytinae species and individuals, respectively, were non-native to North America. 3. We captured more Scolytinae using cottonwood trap-logs compared with control traps in both years, although this was the case with sycamore and sweetgum only in 2013. More woodborers were captured using cottonwood and sweetgum trap-logs compared with control traps in both years, although only with sycamore in 2013. 4. Ethanol was an effective lure for capturing non-native Scolytinae; however, not all non-native species were captured using ethanol lures. Ambrosiophilus atratus (Eichhoff) and Hypothenemus crudiae (Panzer) were captured with both trap-logs and control traps, whereas Coccotrypes distinctus (Motschulsky) and Xyleborus glabratus Eichhoff were only captured on trap-logs. 5. Indicator species analysis revealed that certain scolytines [e.g. Cnestus mutilates (Blandford) and Xylosandrus crassiusculus (Motschulsky)] showed significant associations with trap-logs or ethanol baits in poplar or sweetgum trap-logs. In general, the species composition of subcortical insects, especially woodboring insects, was distinct among the three tree species and between those associated with trap-logs and control traps.

  12. High voltage supply for neutron tubes in well logging applications

    DOE Patents [OSTI]

    Humphreys, D. Russell

    1989-01-01

    A high voltage supply is provided for a neutron tube used in well logging. The "biased pulse" supply of the invention combines DC and "full pulse" techniques and produces a target voltage comprising a substantial negative DC bias component on which is superimposed a pulse whose negative peak provides the desired negative voltage level for the neutron tube. The target voltage is preferably generated using voltage doubling techniques and employing a voltage source which generates bipolar pulse pairs having an amplitude corresponding to the DC bias level.

  13. A Model for Water Factor Measurements With Fission-Neutron Logging Tools

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    (May 1983) | Department of Energy A Model for Water Factor Measurements With Fission-Neutron Logging Tools (May 1983) A Model for Water Factor Measurements With Fission-Neutron Logging Tools (May 1983) A Model for Water Factor Measurements With Fission-Neutron Logging Tools (May 1983) PDF icon A Model for Water Factor Measurements With Fission-Neutron Logging Tools (May 1983) More Documents & Publications Field Calibration Facilities for Environmental Measurement of Radium, Thorium, and

  14. Abbreviated Total-Count Logging Procedures for Use in Remedial Action

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    (December 1982) | Department of Energy Abbreviated Total-Count Logging Procedures for Use in Remedial Action (December 1982) Abbreviated Total-Count Logging Procedures for Use in Remedial Action (December 1982) Abbreviated Total-Count Logging Procedures for Use in Remedial Action (December 1982) PDF icon Abbreviated Total-Count Logging Procedures for Use in Remedial Action (December 1982) More Documents & Publications Field Calibration Facilities for Environmental Measurement of Radium,

  15. Logging into Deltek Time & Expense (T&E) | The Ames Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Logging into Deltek Time & Expense (T&E) Document Number: NA Effective Date: 07/2014

  16. Data Compendium for the Logging Test Pits at the ERDA Grand Junction

    Office of Environmental Management (EM)

    Compound (December 1975) | Department of Energy Data Compendium for the Logging Test Pits at the ERDA Grand Junction Compound (December 1975) Data Compendium for the Logging Test Pits at the ERDA Grand Junction Compound (December 1975) Data Compendium for the Logging Test Pits at the ERDA Grand Junction Compound (December 1975) PDF icon Data Compendium for the Logging Test Pits at the ERDA Grand Junction Compound (December 1975) More Documents & Publications Field Calibration Facilities

  17. Nonprofit Organizations: Have Your Los Alamos Employees/Retirees Log Hours

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    in VolunteerMatch Nonprofit Organizations: Have Your Los Alamos Employees/Retirees Log Hours in VolunteerMatch Community Connections: Your link to news and opportunities from Los Alamos National Laboratory Latest Issue:Mar. 2016 all issues All Issues » submit Nonprofit Organizations: Have Your Los Alamos Employees/Retirees Log Hours in VolunteerMatch Lab employees and retirees should log their VolunteerMatch hours to benefit local nonprofits. March 1, 2013 Volunteers help fill sandbags

  18. Calibration models for density borehole logging - construction report

    SciTech Connect (OSTI)

    Engelmann, R.E.; Lewis, R.E.; Stromswold, D.C.

    1995-10-01

    Two machined blocks of magnesium and aluminum alloys form the basis for Hanford`s density models. The blocks provide known densities of 1.780 {plus_minus} 0.002 g/cm{sup 3} and 2.804 {plus_minus} 0.002 g/cm{sup 3} for calibrating borehole logging tools that measure density based on gamma-ray scattering from a source in the tool. Each block is approximately 33 x 58 x 91 cm (13 x 23 x 36 in.) with cylindrical grooves cut into the sides of the blocks to hold steel casings of inner diameter 15 cm (6 in.) and 20 cm (8 in.). Spacers that can be inserted between the blocks and casings can create air gaps of thickness 0.64, 1.3, 1.9, and 2.5 cm (0.25, 0.5, 0.75 and 1.0 in.), simulating air gaps that can occur in actual wells from hole enlargements behind the casing.

  19. Fluid-Rock Characterization and Interactions in NMR Well Logging

    SciTech Connect (OSTI)

    Hirasaki, George J.; Mohanty, Kishore, K.

    2001-07-13

    The objective of this project is to characterize the fluid properties and fluid-rock interactions that are needed for formation evaluation by NMR well logging. This is the first annual progress report submitted to the DOE. It reports on the work completed during the reporting period even if it may have started before this period. This project is a partnership between Professor George J. Hirasaki at Rice University and Professor Kishore Mohanty at University of Houston. In addition to the DOE, this project is supported by a consortium of oil companies and service companies. The fluid properties characterization has emphasized the departure of live oils from correlations based on dead oils. Also, asphaltic components can result in a difference between the T1 and T2 relaxation time distributions as well as reduce the hydrogen index. The fluid rock characterizations that are reported here are the effects of wettability and internal magnetic field gradients. A pore reconstruction method ha s been developed to recreate three-dimensional porous media from two-dimensional images that reproduce some of their key statistical properties. A Monte Carlo simulation technique has been developed to calculate the magnetization decay in fluid saturated porous media given their pore structure.

  20. Resistivity Log At Fort Bliss Area (Combs, Et Al., 1999) | Open...

    Open Energy Info (EERE)

    well. A suite of geophysical logs (gamma ray, neutron, sonic, and resistivity) was also run after completion of drilling. References Jim Combs, John T. Finger, Colin Goranson,...

  1. Gamma Log At Fort Bliss Area (Combs, Et Al., 1999) | Open Energy...

    Open Energy Info (EERE)

    well. A suite of geophysical logs (gamma ray, neutron, sonic, and resistivity) was also run after completion of drilling. References Jim Combs, John T. Finger, Colin Goranson,...

  2. Neutron Log At Fort Bliss Area (Combs, Et Al., 1999) | Open Energy...

    Open Energy Info (EERE)

    well. A suite of geophysical logs (gamma ray, neutron, sonic, and resistivity) was also run after completion of drilling. References Jim Combs, John T. Finger, Colin Goranson,...

  3. Density Log at Fish Lake Valley Area (DOE GTP) | Open Energy...

    Open Energy Info (EERE)

    Fish Lake Valley Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Density Log at Fish Lake Valley Area (DOE GTP) Exploration...

  4. Resistivity Log At Fish Lake Valley Area (DOE GTP) | Open Energy...

    Open Energy Info (EERE)

    Fish Lake Valley Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Resistivity Log At Fish Lake Valley Area (DOE GTP) Exploration...

  5. FMI Log At New River Area (DOE GTP) | Open Energy Information

    Open Energy Info (EERE)

    GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: FMI Log At New River Area (DOE GTP) Exploration Activity Details Location New River Area...

  6. Density Log at Gabbs Valley Area (DOE GTP) | Open Energy Information

    Open Energy Info (EERE)

    Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Density Log at Gabbs Valley Area (DOE GTP) Exploration Activity Details Location Gabbs Valley...

  7. Density Log at Fort Bliss Area (DOE GTP) | Open Energy Information

    Open Energy Info (EERE)

    Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Density Log at Fort Bliss Area (DOE GTP) Exploration Activity Details Location Fort Bliss...

  8. Density Log at Silver Peak Area (DOE GTP) | Open Energy Information

    Open Energy Info (EERE)

    Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Density Log at Silver Peak Area (DOE GTP) Exploration Activity Details Location Silver Peak...

  9. Density Log at Alum Area (Moos & Ronne, 2010) | Open Energy Informatio...

    Open Energy Info (EERE)

    Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Density Log at Alum Area (Moos & Ronne, 2010) Exploration Activity Details Location Alum...

  10. Well Log Techniques At Snake River Plain Region (DOE GTP) | Open...

    Open Energy Info (EERE)

    navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Well Log Techniques At Snake River Plain Region (DOE GTP) Exploration Activity Details Location Snake...

  11. Pressure Temperature Log At Soda Lake Area (DOE GTP) | Open Energy...

    Open Energy Info (EERE)

    navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Pressure Temperature Log At Soda Lake Area (DOE GTP) Exploration Activity Details Location Soda Lake...

  12. FMI Log At Glass Buttes Area (DOE GTP) | Open Energy Information

    Open Energy Info (EERE)

    Glass Buttes Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: FMI Log At Glass Buttes Area (DOE GTP) Exploration Activity Details...

  13. Gamma Log At Flint Geothermal Area (DOE GTP) | Open Energy Information

    Open Energy Info (EERE)

    Flint Geothermal Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Gamma Log At Flint Geothermal Area (DOE GTP) Exploration Activity...

  14. Gamma Log At Silver Peak Area (DOE GTP) | Open Energy Information

    Open Energy Info (EERE)

    Silver Peak Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Gamma Log At Silver Peak Area (DOE GTP) Exploration Activity Details...

  15. Resistivity Log At Fort Bliss Area (DOE GTP) | Open Energy Information

    Open Energy Info (EERE)

    DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Resistivity Log At Fort Bliss Area (DOE GTP) Exploration Activity Details Location Fort...

  16. Neutron Log At Silver Peak Area (DOE GTP) | Open Energy Information

    Open Energy Info (EERE)

    Silver Peak Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Neutron Log At Silver Peak Area (DOE GTP) Exploration Activity Details...

  17. Acoustic Logs At The Needles Area (DOE GTP) | Open Energy Information

    Open Energy Info (EERE)

    The Needles Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Acoustic Logs At The Needles Area (DOE GTP) Exploration Activity...

  18. Resistivity Log At The Needles Area (DOE GTP) | Open Energy Informatio...

    Open Energy Info (EERE)

    The Needles Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Resistivity Log At The Needles Area (DOE GTP) Exploration Activity...

  19. Well Log Data At Dixie Valley Geothermal Area (Mallan, Et Al...

    Open Energy Info (EERE)

    conducted to help characterize the geothermal reservoir by employing electromagnetic induction logging. The goal was to discern subsurface features that are useful in geothermal...

  20. Well Log Data At Dixie Valley Geothermal Area (Barton, Et Al...

    Open Energy Info (EERE)

    Exploration Basis Well log data was used to investigate the relationship between permeability and the contemporary in situ stress field in the Dixie Valley Geothermal Reservoir....

  1. Cross-Dipole Acoustic Log At Alum Area (Moos & Ronne, 2010) ...

    Open Energy Info (EERE)

    oriented in the strike direction of the fault and of the dipping sediments. References Daniel Moos, Joel Ronne (2010) Selecting The Optimal Logging Suite For Geothermal Reservoir...

  2. Summary Report of Geophysical Logging For The Seismic Boreholes Project at the Hanford Site Waste Treatment Plant.

    SciTech Connect (OSTI)

    Gardner, Martin G.; Price, Randall K.

    2007-02-01

    During the period of June through October 2006, three deep boreholes and one corehole were drilled beneath the site of the Waste Treatment Plant (WTP) at the U.S. Department of Energy (DOE) Hanford Site near Richland, Washington. The boreholes were drilled to provide information on ground-motion attenuation in the basalt and interbedded sediments underlying the WTP site. This report describes the geophysical logging of the deep boreholes that was conducted in support of the Seismic Boreholes Project, defined below. The detailed drilling and geological descriptions of the boreholes and seismic data collected and analysis of that data are reported elsewhere.

  3. TMACS test procedure TP005: Sensor configuration, logging, and data conversion. Revision 4

    SciTech Connect (OSTI)

    Washburn, S.J.

    1994-08-25

    The TMACS Software Project Test Procedures translate the project`s acceptance criteria into test steps. Software releases are certified when the affected Test Procedures are successfully performed and the customers authorize installation of these changes. This Test Procedure addresses the sensor configuration, conversion and logging requirements of the TMACS. The features to be tested are as follows: sensor configuration data; conversion of continuous sensor data to engineering units; conversion of digital data to discrete states; discrete sensor data logging; and continuous sensor data logging.

  4. Property:Building/SPPurchasedEngyNrmlYrMwhYrLogs | Open Energy...

    Open Energy Info (EERE)

    Datasets Community Login | Sign Up Search Property Edit with form History Property:BuildingSPPurchasedEngyNrmlYrMwhYrLogs Jump to: navigation, search This is a property of type...

  5. Temperatures and Natural Gamma-Ray Logs Obtained in 1986 from...

    Open Energy Info (EERE)

    of the formation to absorb injected fluid after the well was completed. Changes in temperature logs run in July and September appear to result from fluid loss to the...

  6. Lithology and well log study of Campbell E-2 geothermal test...

    Open Energy Info (EERE)

    well log study of Campbell E-2 geothermal test well, Humboldt House geothermal prospect, Pershing County, Nevada Jump to: navigation, search OpenEI Reference LibraryAdd to library...

  7. Method for determining formation quality factor from well log data and its

    Office of Scientific and Technical Information (OSTI)

    application to seismic reservoir characterization (Patent) | SciTech Connect Patent: Method for determining formation quality factor from well log data and its application to seismic reservoir characterization Citation Details In-Document Search Title: Method for determining formation quality factor from well log data and its application to seismic reservoir characterization A method for seismic characterization of subsurface Earth formations includes determining at least one of

  8. Method for determining formation quality factor from well log data and its

    Office of Scientific and Technical Information (OSTI)

    application to seismic reservoir characterization (Patent) | SciTech Connect Patent: Method for determining formation quality factor from well log data and its application to seismic reservoir characterization Citation Details In-Document Search Title: Method for determining formation quality factor from well log data and its application to seismic reservoir characterization × You are accessing a document from the Department of Energy's (DOE) SciTech Connect. This site is a product of DOE's

  9. Is the assumption of normality or log-normality for continuous response data critical for benchmark dose estimation?

    SciTech Connect (OSTI)

    Shao, Kan; Gift, Jeffrey S.; Setzer, R. Woodrow

    2013-11-01

    Continuous responses (e.g. body weight) are widely used in risk assessment for determining the benchmark dose (BMD) which is used to derive a U.S. EPA reference dose. One critical question that is not often addressed in doseresponse assessments is whether to model the continuous data as normally or log-normally distributed. Additionally, if lognormality is assumed, and only summarized response data (i.e., mean standard deviation) are available as is usual in the peer-reviewed literature, the BMD can only be approximated. In this study, using the hybrid method and relative deviation approach, we first evaluate six representative continuous doseresponse datasets reporting individual animal responses to investigate the impact on BMD/BMDL estimates of (1) the distribution assumption and (2) the use of summarized versus individual animal data when a log-normal distribution is assumed. We also conduct simulation studies evaluating model fits to various known distributions to investigate whether the distribution assumption has influence on BMD/BMDL estimates. Our results indicate that BMDs estimated using the hybrid method are more sensitive to the distribution assumption than counterpart BMDs estimated using the relative deviation approach. The choice of distribution assumption has limited impact on the BMD/BMDL estimates when the within dose-group variance is small, while the lognormality assumption is a better choice for relative deviation method when data are more skewed because of its appropriateness in describing the relationship between mean and standard deviation. Additionally, the results suggest that the use of summarized data versus individual response data to characterize log-normal distributions has minimal impact on BMD estimates. - Highlights: We investigate to what extent the distribution assumption can affect BMD estimates. Both real data analysis and simulation study are conducted. BMDs estimated using hybrid method are more sensitive to distribution assumption. Summarized continuous data are adequate for BMD estimation.

  10. Evaluation of Simple Causal Message Logging for Large-Scale Fault Tolerant HPC Systems

    SciTech Connect (OSTI)

    Bronevetsky, G; Meneses, E; Kale, L V

    2011-02-25

    The era of petascale computing brought machines with hundreds of thousands of processors. The next generation of exascale supercomputers will make available clusters with millions of processors. In those machines, mean time between failures will range from a few minutes to few tens of minutes, making the crash of a processor the common case, instead of a rarity. Parallel applications running on those large machines will need to simultaneously survive crashes and maintain high productivity. To achieve that, fault tolerance techniques will have to go beyond checkpoint/restart, which requires all processors to roll back in case of a failure. Incorporating some form of message logging will provide a framework where only a subset of processors are rolled back after a crash. In this paper, we discuss why a simple causal message logging protocol seems a promising alternative to provide fault tolerance in large supercomputers. As opposed to pessimistic message logging, it has low latency overhead, especially in collective communication operations. Besides, it saves messages when more than one thread is running per processor. Finally, we demonstrate that a simple causal message logging protocol has a faster recovery and a low performance penalty when compared to checkpoint/restart. Running NAS Parallel Benchmarks (CG, MG and BT) on 1024 processors, simple causal message logging has a latency overhead below 5%.

  11. Calibration models for measuring moisture in unsaturated formations by neutron logging

    SciTech Connect (OSTI)

    Engelman, R.E.; Lewis, R.E.; Stromswold, D.C.

    1995-10-01

    Calibration models containing known amounts of hydrogen have been constructed to simulate unsaturated earth formations for calibrating neutron well logging tools. The models are made of dry mixtures of hydrated alumina (Al(OH){sub 3}) with either silica sand (SiO{sub 2}) or aluminum oxide (Al{sub 2}O{sub 3}). Hydrogen in the hydrated alumina replaces the hydrogen in water for neutron scattering, making it possible to simulate partially saturated formations. The equivalent water contents for the models are 5%, 12%, 20%, and 40% by volume in seven tanks that have a diameter of 1.5 m and a height of 1.8 m. Steel casings of inside diameter 15.4 cm (for three models) and diameter 20.3 cm (for four models) allow logging tool access to simulate logging through cased boreholes.

  12. Borehole SASW testing to evaluate log(G{sub max}) - log({sigma}{prime}) relationships in situ

    SciTech Connect (OSTI)

    Kalinski, M.E.; Stokoe, K.H. II; Young, Y.L.; Roesset, J.M.

    1999-07-01

    A new method is being developed for the in-situ measurement of shear wave velocity, V{sub s}, in the soil surrounding a borehole. The method involves the measurement of axially propagating surface waves inside an uncased borehole using the Spectral-Analysis-of-Surface-Waves (SASW) approach. Testing if performed with instrumentation housed inside an inflatable tool. Inflation pressures applied by the tool are used to vary radial stresses in the soil surrounding the borehole. Surface wave velocities over a range of frequencies are measured at each inflation pressure. These measurements are then theoretically modeled so that the variation in V{sub s} (an hence small-strain shear module, G{sub max}) with distance behind the borehole wall is determined at each pressure. The results of field tests with the borehole SASW tool at two sites composed of unsaturated clayey soil are presented. These results are compared with independent field seismic measurements and with laboratory tests on intact specimens using the torsional resonant column to assess the validity of the new field method.

  13. E-print Network Web Log News: Research Communications for Scientists and

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Engineers Website Policies and Important Links E-print Web Log E-print Network News E-print Network About Search Browse by Discipline Find Scientific Societies Receive E-print Alerts Contact Us Help Home OSTI DOE Science.gov Description This Web Log provides the latest information about changes to E-print Network - its content, features, and functionality - as well as news or information of interest regarding e-print information in general. Please provide your comments, questions, concerns

  14. Moab Project Safely Logs 2 Million Work Hours | Department of Energy

    Energy Savers [EERE]

    Safely Logs 2 Million Work Hours Moab Project Safely Logs 2 Million Work Hours March 12, 2014 - 12:00pm Addthis Empty containers on haul trucks are being loaded with mill tailings. Empty containers on haul trucks are being loaded with mill tailings. Media Contacts Donald Metzler, Moab Federal Project Director, (970) 257-2115 Wendee Ryan, S&K Aerospace Public Affairs Manager, (970) 257-2145 (Grand Junction, CO) - The number 1,584 may not mean much to most people, but for the workers on the

  15. Borehole induction logging for the Dynamic Underground Stripping Project LLNL gasoline spill site

    SciTech Connect (OSTI)

    Boyd, S.; Newmark, R.; Wilt, M.

    1994-01-21

    Borehole induction logs were acquired for the purpose of characterizing subsurface physical properties and monitoring steam clean up activities at the Lawrence Livermore National Laboratory. This work was part of the Dynamic Underground Stripping Project`s demonstrated clean up of a gasoline spin. The site is composed of unconsolidated days, sands and gravels which contain gasoline both above and below the water table. Induction logs were used to characterize lithology, to provide ``ground truth`` resistivity values for electrical resistance tomography (ERT), and to monitor the movement of an underground steam plume used to heat the soil and drive volatile organic compounds (VOCs) to the extraction wells.

  16. Outage Log

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    10:00 - 16:50. No user impact was expected. These switches provide connectivity for the meta-data servers for homes, common, project, syscomm, dna and projectb. 111115 9:00...

  17. Idaho National Laboratory PCB Annual Document Log and Annual Records Report for calendar year 2014

    SciTech Connect (OSTI)

    Layton, Deborah L.

    2015-06-01

    The requirements for the reporting of polychlorinated biphenyl (PCB)-related activities are found in 40 Code of Federal Regulations (CFR) 761 Subpart J, "General Records and Reports." The PCB Annual Document Log is a detailed record of the PCB waste handling activities at the facility. The facility must prepare it each year by July 1 and maintain it at the facility for at least 3 years after the facility ceases using or storing PCBs and PCB items. While submittal of the PCB Annual Document Log to the U.S. Environmental Protection Agency (EPA) is not required by regulation, EPA has verbally requested in telephone conversations that this report be submitted to them on an annual basis. The Annual Records are not required to be submitted to EPA and are not considered to be part of the Annual Document Log, but are included to provide the complete disposition history or status of all PCB activities during the year. The Annual Document Log section of this report (Section 2.0) meets the requirements of 40 CFR 761.180(a)(2), as applicable, while the Annual Records section (Section 3.0) meets the requirement of 40 CFR 761.180(a)(1).

  18. Correction of steel casing effect for density log using numerical and experimental methods in the slim borehole

    SciTech Connect (OSTI)

    Hwang, Seho; Shin, Jehyun; Kim, Jongman; Won, Byeongho

    2015-03-10

    Density log is widely applied for a variety of fields such as the petroleum exploration, mineral exploration, and geotechnical survey. The logging condition of density log is normally open holes but there are frequently cased boreholes. The primary calibration curve by slim hole logging manufacturer is normally the calibration curves for the variation of borehole diameter. In this study, we have performed the correction of steel casing effects using numerical and experimental methods. We have performed numerical modeling using the Monte Carlo N-Particle (MCNP) code based on Monte Carlo method, and field experimental method from open and cased hole log. In this study, we used the FDGS (Formation Density Gamma Sonde) for slim borehole with a 100 mCi 137Cs source, three inch borehole and steel casing. The casing effect between numerical and experimental method is well matched.

  19. Log-ratio signal-processing technique for beam position monitors

    SciTech Connect (OSTI)

    Shafer, R.E.

    1993-01-01

    Two basic signal-processing techniques are presently in wide use for the processing of signals from beam position monitors (BPMs); difference-over-sum, and amplitude-modulation-to-phase-modulation (AM-PM) conversion. Difference-over-sum offers simplicity and low cost, but poor real-time normalized response and amplitude dynamic range. AM-PM offers fast real-time response and large dynamic range, but is costly and difficult to implement. Logarithmic-ratio processing, a technique using newly available inexpensive hybrid circuits, appears to offer the advantages of both, and the disadvantages of neither. This paper reviews the features techniques, and highlights the features of the log-ratio technique. Among the advantages of log-ratio is a beam-displacement response linearity that is superior to either difference-over-sum or AM-PM for circular-aperture BPMs.

  20. Log-ratio signal-processing technique for beam position monitors

    SciTech Connect (OSTI)

    Shafer, R.E.

    1993-02-01

    Two basic signal-processing techniques are presently in wide use for the processing of signals from beam position monitors (BPMs); difference-over-sum, and amplitude-modulation-to-phase-modulation (AM-PM) conversion. Difference-over-sum offers simplicity and low cost, but poor real-time normalized response and amplitude dynamic range. AM-PM offers fast real-time response and large dynamic range, but is costly and difficult to implement. Logarithmic-ratio processing, a technique using newly available inexpensive hybrid circuits, appears to offer the advantages of both, and the disadvantages of neither. This paper reviews the features techniques, and highlights the features of the log-ratio technique. Among the advantages of log-ratio is a beam-displacement response linearity that is superior to either difference-over-sum or AM-PM for circular-aperture BPMs.

  1. Quantification of Wellbore Leakage Risk Using Non-destructive Borehole Logging Techniques

    SciTech Connect (OSTI)

    Duguid, Andrew; Butsch, Robert; Cary, J.; Celia, Michael; Chugunov, Nikita; Gasda, Sarah; Hovorka, Susan; Ramakrishnan, T. S.; Stamp, Vicki; Thingelstad, Rebecca; Wang, James

    2014-08-29

    Well integrity is important at all potential CCS locations and may play a crucial role establishing leakage risk in areas where there is a high density of existing wells that could be impacted by the storage operations including depleted petroleum fields where EOR or CCS will occur. To address a need for risk quantification methods that can be directly applied to individual wells using borehole logging tools a study was conducted using data from five wells in Wyoming. The objectives of the study were: Objective 1: Develop methods to establish the baseline flow parameters (porosity and permeability or mobility) from individual measurements of the material properties and defects in a well. Objective 2: Develop a correlation between field flow-property data and cement logs that can be used to establish the flow-properties of well materials and well features using cement mapping tools. Objective 3: Establish a method that uses the flow-property model (Objective 2) to analyze the statistical uncertainties associated with individual well leakage that can provide basis for uncertainty in risk calculations. The project objectives were met through the logging of five wells in Carbon and Natrona County Wyoming to collect data that was used to estimate individual and average well flow properties and model the results using ultrasonic data collected during the logging. Three of the five wells provided data on point and average flow properties for well annuli. Data from the other two wells were used to create models of cement permeability and test whether information collected in one well could be used to characterize another well. The results of the in-situ point measurements were confirmed by the lab measurements sidewall cores collected near the same depths Objective 1 was met using the data collected through logging, testing, and sampling. The methods were developed that can establish baseline flow parameters of wells by both point and average test methods. The methods to estimate the flow properties modeling of point pressure tests, modeling of vertical interference tests, and laboratory measurement of cased-hole sidewall cores The wells were in sufficiently good shape to allow the development of the characterization methods while still having enough defects to study differences in results as they relate to well integrity. Samples and tests analyzed from three of five wells studied in showed the cements were largely intact and had not degraded from exposure native brines. Log results taken in conjunction with the core measurements indicate that interfaces and/or problems with cement placement due to eccentering provide preferential flow paths for fluids, which can increase the effective permeability of the barrier several orders of magnitude above the permeability of intact cement. The results of the maps created using logging tools indicating that the cement condition and bond are generally good identify a need for more research to understand how logs can be used to predicteffective well permeabilities such as those measured by the VITs in this study.

  2. Evaluation of Non-Nuclear Techniques for Well Logging: Final Report

    SciTech Connect (OSTI)

    Bond, Leonard J.; Griffin, Jeffrey W.; Harris, R. V.; Denslow, Kayte M.; Moran, Traci L.

    2011-08-01

    The focus of this study is the understanding of the technical obstacles that hinder the replacement of and the disadvantages from the loss of extensive interpretation experience based on data accumulated with AmBe. Enhanced acoustic and electromagnetic sensing methods in combination with non-isotope-based well logging techniques have the potential to complement and/or replace existing isotope-based techniques, providing the opportunity to reduce oil industry dependence on isotopic sources such as AmBe.

  3. A Statistical Characterization of School Bus Drive Cycles Collected via Onboard Logging Systems

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ____________________________________ 2013-01-2400 Published 09/24/2013 doi:10.4271/2013-01-2400 saecomveh.saejournals.org A Statistical Characterization of School Bus Drive Cycles Collected via Onboard Logging Systems Adam Duran and Kevin Walkowicz National Renewable Energy Laboratory ABSTRACT In an effort to characterize the dynamics typical of school bus operation, National Renewable Energy Laboratory (NREL) researchers set out to gather in-use duty cycle data from school bus fleets operating

  4. U-039: ISC Update: BIND 9 Resolver crashes after logging an error in query.c

    Broader source: Energy.gov [DOE]

    A remote server can cause the target connected client to crash. Organizations across the Internet are reporting crashes interrupting service on BIND 9 nameservers performing recursive queries. Affected servers crash after logging an error in query.c with the following message: "INSIST(! dns_rdataset_isassociated(sigrdataset))" Multiple versions are reported as being affected, including all currently supported release versions of ISC BIND 9. ISC is actively investigating the root cause and working to produce patches which avoid the crash.

  5. U-038: BIND 9 Resolver crashes after logging an error in query.c

    Broader source: Energy.gov [DOE]

    A remote server can cause the target connected client to crash. Organizations across the Internet are reporting crashes interrupting service on BIND 9 nameservers performing recursive queries. Affected servers crash after logging an error in query.c with the following message: "INSIST(! dns_rdataset_isassociated(sigrdataset))" Multiple versions are reported as being affected, including all currently supported release versions of ISC BIND 9. ISC is actively investigating the root cause and working to produce patches which avoid the crash.

  6. High-voltage supply for neutron tubes in well-logging applications

    DOE Patents [OSTI]

    Humphreys, D.R.

    1982-09-15

    A high voltage supply is provided for a neutron tube used in well logging. The biased pulse supply of the invention combines DC and full pulse techniques and produces a target voltage comprising a substantial negative DC bias component on which is superimposed a pulse whose negative peak provides the desired negative voltage level for the neutron tube. The target voltage is preferably generated using voltage doubling techniques and employing a voltage source which generates bipolar pulse pairs having an amplitude corresponding to the DC bias level.

  7. Method of assaying uranium with prompt fission and thermal neutron borehole logging adjusted by borehole physical characteristics. [Patient application

    DOE Patents [OSTI]

    Barnard, R.W.; Jensen, D.H.

    1980-11-05

    Uranium formations are assayed by prompt fission neutron logging techniques. The uranium in the formation is proportional to the ratio of epithermal counts to thermal or epithermal dieaway. Various calibration factors enhance the accuracy of the measurement.

  8. Method of assaying uranium with prompt fission and thermal neutron borehole logging adjusted by borehole physical characteristics

    DOE Patents [OSTI]

    Barnard, Ralston W. (Albuquerque, NM); Jensen, Dal H. (Albuquerque, NM)

    1982-01-01

    Uranium formations are assayed by prompt fission neutron logging techniques. The uranium in the formation is proportional to the ratio of epithermal counts to thermal or eqithermal dieaway. Various calibration factors enhance the accuracy of the measurement.

  9. Calibration of NMR well logs from carbonate reservoirs with laboratory NMR measurements and μXRCT

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Mason, Harris E.; Smith, Megan M.; Hao, Yue; Carroll, Susan A.

    2014-12-31

    The use of nuclear magnetic resonance (NMR) well log data has the potential to provide in-situ porosity, pore size distributions, and permeability of target carbonate CO₂ storage reservoirs. However, these methods which have been successfully applied to sandstones have yet to be completely validated for carbonate reservoirs. Here, we have taken an approach to validate NMR measurements of carbonate rock cores with independent measurements of permeability and pore surface area to volume (S/V) distributions using differential pressure measurements and micro X-ray computed tomography (μXRCT) imaging methods, respectively. We observe that using standard methods for determining permeability from NMR data incorrectlymore » predicts these values by orders of magnitude. However, we do observe promise that NMR measurements provide reasonable estimates of pore S/V distributions, and with further independent measurements of the carbonate rock properties that universally applicable relationships between NMR measured properties may be developed for in-situ well logging applications of carbonate reservoirs.« less

  10. Evaluation of Non-Nuclear Techniques for Well Logging: Technology Evaluation

    SciTech Connect (OSTI)

    Bond, Leonard J.; Denslow, Kayte M.; Griffin, Jeffrey W.; Dale, Gregory E.; Harris, Robert V.; Moran, Traci L.; Sheen, David M.; Schenkel, Thomas

    2010-11-01

    This report presents an initial review of the state-of-the-art nuclear and non-nuclear well logging methods and seeks to understand the technical and economic issues if AmBe, and potentially other isotope sources, are reduced or even eliminated in the oil-field services industry. Prior to considering alternative logging technologies, there is a definite need to open up discussions with industry regarding the feasibility and acceptability of source replacement. Industry views appear to range from those who see AmBe as vital and irreplaceable to those who believe that, with research and investment, it may be possible to transition to electronic neutron sources and employ combinations of non-nuclear technologies to acquire the desired petro-physical parameters. In one sense, the simple answer to the question as to whether petro-physical parameters can be sensed with technologies other than AmBe is probably "Yes". The challenges come when attention turns to record interpretation. The many decades of existing records form a very valuable proprietary resource, and the interpretation of subtle features contained in these records are of significant value to the oil-gas exploration community to correctly characterize a well. The demonstration of equivalence and correspondence/correlation between established and any new sensing modality, and correlations with historic records is critical to ensuring accurate data interpretation. Establishing the technical basis for such a demonstration represents a significant effort.

  11. AVTA Federal Fleet PEV Readiness Data Logging and Characterization Study for the National Park Service: Fort Vancouver National Historic Site

    SciTech Connect (OSTI)

    Stephen Schey; Jim Francfort

    2014-03-01

    Battelle Energy Alliance, LLC, managing and operating contractor for the U.S. Department of Energys Idaho National Laboratory, is the lead laboratory for the U.S. Department of Energys Advanced Vehicle Testing. Battelle Energy Alliance, LLC contracted with Intertek Testing Services, North America (ITSNA) to collect data on federal fleet operations as part of the Advanced Vehicle Testing Activitys Federal Fleet Vehicle Data Logging and Characterization study. The Advanced Vehicle Testing Activity study seeks to collect data to validate the use of advanced electric drive vehicle transportation. This report focuses on the Fort Vancouver National Historic Site (FVNHS) fleet to identify daily operational characteristics of select vehicles and report findings on vehicle and mission characterizations to support the successful introduction of electric vehicles (EVs) into the agencies fleet. Individual observations of the selected vehicles provided the basis for recommendations related to EV adoption and whether a battery electric vehicle (BEV) or plug-in hybrid electric vehicle (PHEV) (collectively plug-in electric vehicles) could fulfill the mission requirements. FVNHS identified three vehicles in its fleet for consideration. While the FVNHS vehicles conduct many different missions, only two (i.e., support and pool missions) were selected by agency management to be part of this fleet evaluation. The logged vehicles included a pickup truck and a minivan. This report will show that BEVs and PHEVs are capable of performing the required missions and providing an alternative vehicle for both mission categories, because each has sufficient range for individual trips and time available each day for charging to accommodate multiple trips per day. These charging events could occur at the vehicles home base, high-use work areas, or in intermediate areas along routes that the vehicles frequently travel. Replacement of vehicles in the current fleet would result in significant reductions in emission of greenhouse gases and petroleum use, while also reducing fuel costs. The Vancouver, Washington area and neighboring Portland, Oregon are leaders in adoption of PEVs in the United States1. PEV charging stations, or more appropriately identified as electric vehicle supply equipment, located on the FVNHS facility would be a benefit for both FVNHS fleets and general public use. Fleet drivers and park visitors operating privately owned plug-in electric vehicles benefit by using the charging infrastructure. ITSNA recommends location analysis of the FVNHS site to identify the optimal station placement for electric vehicle supply equipment. ITSNA recognizes the support of Idaho National Laboratory and ICF International for their efforts to initiate communication with the National Parks Service and FVNHS for participation in this study. ITSNA is pleased to provide this report and is encouraged by the high interest and support from the National Park Service and FVNHS personnel

  12. Shallow infiltration processes at Yucca Mountain, Nevada: Neutron logging data 1984--1993

    SciTech Connect (OSTI)

    Flint, L.E.; Flint, A.L.

    1995-12-31

    To determine site suitability of Yucca Mountain, Nevada, as a potential high-level radioactive waste repository, a study was devised to characterize net infiltration. This study involves a detailed data set produced from 99 neutron boreholes that consisted of volumetric water-content readings with depth from 1984 through 1993 at Yucca Mountain. Boreholes were drilled with minimal disturbance to the surrounding soil or rock in order to best represent field conditions. Boreholes were located in topographic positions representing infiltration zones identified as ridgetops, sideslopes, terraces, and active channels. Through careful field calibration, neutron moisture logs, collected on a monthly basis and representing most of the areal locations at Yucca Mountain, illustrated that the depth of penetration of seasonal moisture, important for escaping loss to evapotranspiration, was influenced by several factors. It was increased (1) by thin soil cover, especially in locations where thin soil is underlain by fractured bedrock; (2) on ridgetops; and (3) during the winter when evapotranspiration is low and runoff is less frequent. This data set helps to provide a seasonal and areal distribution of changes in volumetric water content with which to assess hydrologic processes contributing to net infiltration.

  13. Shallow infiltration processes at Yucca Mountain, Nevada - neutron logging data 1984-93

    SciTech Connect (OSTI)

    Flint, L.E.; Flint, A.L.

    1995-11-01

    To determine site suitability of Yucca Mountain, Nevada, as a potential high-level radioactive waste repository, a study was devised to characterize net infiltration. This study involves a detailed data set produced from 99 neutron boreholes that consisted of volumetric water-content readings with depth from 1984 through 1993 at Yucca Mountain. Boreholes were drilled with minimal disturbance to the surrounding soil or rock in order to best represent field conditions. Boreholes were located in topographic positions representing infiltration zones identified as ridge-tops, sideslopes, terraces, and active channels. Through careful field calibration, neutron moisture logs, collected on a monthly basis and representing most of the areal locations at Yucca Mountain, illustrated that the depth of penetration of seasonal moisture, important for escaping loss to evapotranspiration, was influenced by several factors. It was increased (1) by thin soil cover, especially in locations where thin soil is underlain by fractured bedrock; (2) on ridgetops; and (3) during the winter when evapotranspiration is low and runoff is less frequent. This data set helps to provide a seasonal and areal distribution of changes in volumetric water content with which to assess hydrologic processes contributing to net infiltration.

  14. Parameter estimation from flowing fluid temperature logging data in unsaturated fractured rock using multiphase inverse modeling

    SciTech Connect (OSTI)

    Mukhopadhyay, S.; Tsang, Y.; Finsterle, S.

    2009-01-15

    A simple conceptual model has been recently developed for analyzing pressure and temperature data from flowing fluid temperature logging (FFTL) in unsaturated fractured rock. Using this conceptual model, we developed an analytical solution for FFTL pressure response, and a semianalytical solution for FFTL temperature response. We also proposed a method for estimating fracture permeability from FFTL temperature data. The conceptual model was based on some simplifying assumptions, particularly that a single-phase airflow model was used. In this paper, we develop a more comprehensive numerical model of multiphase flow and heat transfer associated with FFTL. Using this numerical model, we perform a number of forward simulations to determine the parameters that have the strongest influence on the pressure and temperature response from FFTL. We then use the iTOUGH2 optimization code to estimate these most sensitive parameters through inverse modeling and to quantify the uncertainties associated with these estimated parameters. We conclude that FFTL can be utilized to determine permeability, porosity, and thermal conductivity of the fracture rock. Two other parameters, which are not properties of the fractured rock, have strong influence on FFTL response. These are pressure and temperature in the borehole that were at equilibrium with the fractured rock formation at the beginning of FFTL. We illustrate how these parameters can also be estimated from FFTL data.

  15. Posterior propriety for hierarchical models with log-likelihoods that have norm bounds

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Michalak, Sarah E.; Morris, Carl N.

    2015-07-17

    Statisticians often use improper priors to express ignorance or to provide good frequency properties, requiring that posterior propriety be verified. Our paper addresses generalized linear mixed models, GLMMs, when Level I parameters have Normal distributions, with many commonly-used hyperpriors. It provides easy-to-verify sufficient posterior propriety conditions based on dimensions, matrix ranks, and exponentiated norm bounds, ENBs, for the Level I likelihood. Since many familiar likelihoods have ENBs, which is often verifiable via log-concavity and MLE finiteness, our novel use of ENBs permits unification of posterior propriety results and posterior MGF/moment results for many useful Level I distributions, including those commonlymore » used with multilevel generalized linear models, e.g., GLMMs and hierarchical generalized linear models, HGLMs. Furthermore, those who need to verify existence of posterior distributions or of posterior MGFs/moments for a multilevel generalized linear model given a proper or improper multivariate F prior as in Section 1 should find the required results in Sections 1 and 2 and Theorem 3 (GLMMs), Theorem 4 (HGLMs), or Theorem 5 (posterior MGFs/moments).« less

  16. A Brief Review of the Basis for, and the Procedures Currently Utilized in, Gross Gamma-Ray Log Calibration (October 1976)

    Broader source: Energy.gov [DOE]

    A Brief Review of the Basis for, and the Procedures Currently Utilized in, Gross Gamma-Ray Log Calibration (October 1976)

  17. Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    SunShot Grand Challenge: Regional Test Centers Analysis Home/Tag:Analysis - Electricity use by water service sector and county. Shown are electricity use by (a) large-scale conveyance, (b) groundwater irrigation pumping, (c) surface water irrigation pumping, (d) drinking water, and (e) wastewater. Aggregate electricity use across these sectors (f) is also mapped. Permalink Gallery Sandians Recognized in Environmental Science & Technology's Best Paper Competition Analysis, Capabilities,

  18. Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Analysis Home/Analysis - Structures of the zwitterionic coatings synthesized for this study. Permalink Gallery Investigations on Anti-biofouling Zwitterionic Coatings for MHK Is Now in Press Analysis, Capabilities, Energy, News, News & Events, Renewable Energy, Research & Capabilities, Water Power Investigations on Anti-biofouling Zwitterionic Coatings for MHK Is Now in Press Sandia's Marine Hydrokinetic (MHK) Advanced Materials program has a new publication on the antifouling efficacy

  19. Final Data Report: P- and S-Wave Velocity Logging Borings C4993, C4996, and C4997 Part B: Overall Logs

    SciTech Connect (OSTI)

    Diehl, John; Steller, Robert

    2007-03-20

    Insitu borehole P- and S-wave velocity measurements were collected in three borings located within the Waste Treatment Plant (WTP) boundaries at the Hanford Site, southeastern Washington. Geophysical data acquisition was performed between August and October of 2006 by Rob Steller, Charles Carter, Antony Martin and John Diehl of GEOVision. Data analysis was performed by Rob Steller and John Diehl, and reviewed by Antony Martin of GEOVision, and report preparation was performed by John Diehl and reviewed by Rob Steller. The work was performed under subcontract with Battelle, Pacific Northwest Division with Marty Gardner as Battelles Technical Representative and Alan Rohay serving as the Technical Administrator for Pacific Northwest National Laboratory (PNNL). This report describes the field measurements, data analysis, and results of this work.

  20. AVTA Federal Fleet PEV Readiness Data Logging and Characterization Study for the National Park Service: Golden Gate National Recreation Area

    SciTech Connect (OSTI)

    Stephen Schey; Jim Francfort

    2014-03-01

    Battelle Energy Alliance, LLC, managing and operating contractor for the U.S. Department of Energy's Idaho National Laboratory, is the lead laboratory for U.S. Department of Energy Advanced Vehicle Testing. Battelle Energy Alliance, LLC contracted with Intertek Testing Services, North America (ITSNA) to collect data on federal fleet operations as part of the Advanced Vehicle Testing Activity's Federal Fleet Vehicle Data Logging and Characterization study. The Advanced Vehicle Testing Activity study seeks to collect data to validate the utilization of advanced electric drive vehicle transportation. This report focuses on the Golden Gate National Recreation Area (GGNRA) fleet to identify daily operational characteristics of select vehicles and report findings on vehicle and mission characterizations to support the successful introduction of plug-in electric vehicles (PEVs) into the agencies' fleets. Individual observations of these selected vehicles provide the basis for recommendations related to electric vehicle adoption and whether a battery electric vehicle or plug-in hybrid electric vehicle (PHEV) (collectively PEVs) can fulfill the mission requirements. GGNRA identified 182 vehicles in its fleet, which are under the management of the U.S. General Services Administration. Fleet vehicle mission categories are defined in Section 4, and while the GGNRA vehicles conduct many different missions, only two (i.e., support and law enforcement missions) were selected by agency management to be part of this fleet evaluation. The selected vehicles included sedans, trucks, and sport-utility vehicles. This report will show that battery electric vehicles and/or PHEVs are capable of performing the required missions and providing an alternative vehicle for support vehicles and PHEVs provide the same for law enforcement, because each has a sufficient range for individual trips and time is available each day for charging to accommodate multiple trips per day. These charging events could occur at the vehicle home base, high-use work areas, or intermediately along routes that the vehicles frequently travel. Replacement of vehicles in the current fleet would result in significant reductions in the emission of greenhouse gases and petroleum use, while also reducing fuel costs. The San Francisco Bay Area is a leader in the adoption of PEVs in the United States. PEV charging stations, or more appropriately identified as electric vehicle supply equipment, located on the GGNRA facility would be a benefit for both GGNRA fleets and general public use. Fleet drivers and park visitors operating privately owned PEVs benefit by using the charging infrastructure. ITSNA recommends location analysis of the GGNRA site to identify the optimal placement of the electric vehicle supply equipment station. ITSNA recognizes the support of Idaho National Laboratory and ICF International for their efforts to initiate communication with the National Parks Service and GGNRA for participation in the study. ITSNA is pleased to provide this report and is encouraged by the high interest and support from the National Park Service and GGNRA personnel.

  1. IMPROVED V II log(gf) VALUES, HYPERFINE STRUCTURE CONSTANTS, AND ABUNDANCE DETERMINATIONS IN THE PHOTOSPHERES OF THE SUN AND METAL-POOR STAR HD 84937

    SciTech Connect (OSTI)

    Wood, M. P.; Lawler, J. E.; Den Hartog, E. A.; Sneden, C.; Cowan, J. J. E-mail: jelawler@wisc.edu E-mail: chris@verdi.as.utexas.edu

    2014-10-01

    New experimental absolute atomic transition probabilities are reported for 203 lines of V II. Branching fractions are measured from spectra recorded using a Fourier transform spectrometer and an echelle spectrometer. The branching fractions are normalized with radiative lifetime measurements to determine the new transition probabilities. Generally good agreement is found between this work and previously reported V II transition probabilities. Two spectrometers, independent radiometric calibration methods, and independent data analysis routines enable a reduction in systematic uncertainties, in particular those due to optical depth errors. In addition, new hyperfine structure constants are measured for selected levels by least squares fitting line profiles in the FTS spectra. The new V II data are applied to high resolution visible and UV spectra of the Sun and metal-poor star HD 84937 to determine new, more accurate V abundances. Lines covering a range of wavelength and excitation potential are used to search for non-LTE effects. Very good agreement is found between our new solar photospheric V abundance, log ?(V) = 3.95 from 15 V II lines, and the solar-system meteoritic value. In HD 84937, we derive [V/H] = 2.08 from 68 lines, leading to a value of [V/Fe] = 0.24.

  2. Identification and Characterization of Hydrogeologic Units at the Nevada Test Site Using Geophysical Logs: Examples from the Underground Test Area Project

    SciTech Connect (OSTI)

    Lance Prothro, Sigmund Drellack, Margaret Townsend

    2009-03-25

    The diverse and complex geology of the Nevada Test Site region makes for a challenging environment for identifying and characterizing hydrogeologic units penetrated by wells drilled for the U.S. Department of Energy, National Nuclear Security Administration, Underground Test Area (UGTA) Environmental Restoration Sub-Project. Fortunately, UGTA geoscientists have access to large and robust sets of subsurface geologic data, as well as a large historical knowledge base of subsurface geological analyses acquired mainly during the underground nuclear weapons testing program. Of particular importance to the accurate identification and characterization of hydrogeologic units in UGTA boreholes are the data and interpretation principles associated with geophysical well logs. Although most UGTA participants and stakeholders are probably familiar with drill hole data such as drill core and cuttings, they may be less familiar with the use of geophysical logs; this document is meant to serve as a primer on the use of geophysical logs in the UGTA project. Standard geophysical logging tools used in the UGTA project to identify and characterize hydrogeologic units are described, and basic interpretation principles and techniques are explained. Numerous examples of geophysical log data from a variety of hydrogeologic units encountered in UGTA wells are presented to highlight the use and value of geophysical logs in the accurate hydrogeologic characterization of UGTA wells.

  3. Consortium for coal log pipeline research and development. Final technical progress report, August 10, 1993--August 9, 1996

    SciTech Connect (OSTI)

    Marrero, T.R.

    1996-10-01

    The main objective of this project was to conduct intensive research and development of the Coal Log Pipeline (CLP). Specifically, the R & D was to concentrate on previously neglected and insufficiently studied aspects of CLP which were deemed significant. With improvements in these areas, CLP could be implemented for commercial use within five years. CLP technology is capable of transporting coal logs for long distances. The many potential advantages of CLP over truck and railroad transportation include: lower freight costs, less energy consumption, less air pollution, decreased environmental problems, increased safety, and improved reliability. Previous studies have shown that CLP is advantageous over slurry pipeline technology. First, CLP uses one-third the water required by a coal slurry pipeline. Second, CLP provides easier coal dewatering. Third, the CLP conveying capacity of coal is twice as much as a slurry transport line of equal diameter. In many situations, the cost for transporting each ton of coal is expected to be less expensive by CLP as compared to other competing modes of transportation such as: truck, unit train and slurry pipeline.

  4. Statistical Characterization of School Bus Drive Cycles Collected via Onboard Logging Systems

    SciTech Connect (OSTI)

    Duran, A.; Walkowicz, K.

    2013-10-01

    In an effort to characterize the dynamics typical of school bus operation, National Renewable Energy Laboratory (NREL) researchers set out to gather in-use duty cycle data from school bus fleets operating across the country. Employing a combination of Isaac Instruments GPS/CAN data loggers in conjunction with existing onboard telemetric systems resulted in the capture of operating information for more than 200 individual vehicles in three geographically unique domestic locations. In total, over 1,500 individual operational route shifts from Washington, New York, and Colorado were collected. Upon completing the collection of in-use field data using either NREL-installed data acquisition devices or existing onboard telemetry systems, large-scale duty-cycle statistical analyses were performed to examine underlying vehicle dynamics trends within the data and to explore vehicle operation variations between fleet locations. Based on the results of these analyses, high, low, and average vehicle dynamics requirements were determined, resulting in the selection of representative standard chassis dynamometer test cycles for each condition. In this paper, the methodology and accompanying results of the large-scale duty-cycle statistical analysis are presented, including graphical and tabular representations of a number of relationships between key duty-cycle metrics observed within the larger data set. In addition to presenting the results of this analysis, conclusions are drawn and presented regarding potential applications of advanced vehicle technology as it relates specifically to school buses.

  5. Methods and apparatus to produce stick-slip motion of logging tool attached to a wireline drawn upward by a continuously rotating wireline drum

    DOE Patents [OSTI]

    Vail, III, William Banning (Bothell, WA); Momii, Steven Thomas (Seattle, WA)

    1998-01-01

    Methods and apparatus are described to produce stick-slip motion of a logging tool within a cased well attached to a wireline that is drawn upward by a continuously rotating wireline drum. The stick-slip motion results in the periodic upward movement of the tool in the cased well described in terms of a dwell time during which time the tool is stationary, the move time during which time the tool moves, and the stroke that is upward distance that the tool translates during the "slip" portion of the stick-slip motion. This method of measurement is used to log the well at different vertical positions of the tool. Therefore, any typical "station-to-station logging tool" may be modified to be a "continuous logging tool", where "continuous" means that the wireline drum continually rotates while the tool undergoes stick-slip motion downhole and measurements are performed during the dwell times when the tool is momentarily stationary. The stick-slip methods of operation and the related apparatus are particularly described in terms of making measurements of formation resistivity from within a cased well during the dwell times when the tool is momentarily stationary during the periodic stick-slip motion of the logging tool.

  6. Methods and apparatus to produce stick-slip motion of logging tool attached to a wireline drawn upward by a continuously rotating wireline drum

    DOE Patents [OSTI]

    Vail, W.B. III; Momii, S.T.

    1998-02-10

    Methods and apparatus are described to produce stick-slip motion of a logging tool within a cased well attached to a wireline that is drawn upward by a continuously rotating wireline drum. The stick-slip motion results in the periodic upward movement of the tool in the cased well described in terms of a dwell time during which time the tool is stationary, the move time during which time the tool moves, and the stroke that is upward distance that the tool translates during the ``slip`` portion of the stick-slip motion. This method of measurement is used to log the well at different vertical positions of the tool. Therefore, any typical ``station-to-station logging tool`` may be modified to be a ``continuous logging tool,`` where ``continuous`` means that the wireline drum continually rotates while the tool undergoes stick-slip motion downhole and measurements are performed during the dwell times when the tool is momentarily stationary. The stick-slip methods of operation and the related apparatus are particularly described in terms of making measurements of formation resistivity from within a cased well during the dwell times when the tool is momentarily stationary during the periodic stick-slip motion of the logging tool. 12 figs.

  7. Logging in to Franklin

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Freedom is suitable for running memory-intensive utilities and serial programs like IDL, DDT, parallel make, hsi, and htar. The command to access Freedom is: % ssh -l username...

  8. FOIA Log 2014.xlsx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Closed Corespond ance No. FOIA No. Dated Date Rec'd Requestor HQ, EMCBC or Direct Subject 1/21/14 14-0103 14-001 1/21/2013 12/20/2013 Kelly Vaselli/Fadduol, Cluff & Hardy, P.C. Direct WIPP Fire/Medic Personnel Responding to an Oilfield Fire at XTO Well "Nash49H" on November 8, 2012 4/2/14 14-0126 14-002 2/17/2014 2/17/2014 Zack Ponce, Reporter @ Carlsbad Curren Direct Records Relating to the Inspection Reports for Fire Suppression Systems and CAMs Used in the U/G from 01/01/2010

  9. FOIA Log 2013.xlsx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    121013 13-0168 13-005 11182013 11262013 Jeanne Haffner, Dept. of the History of Science, Harvard University Direct Request for All Records Related to PICs, or Marker for...

  10. FOIA Log 2012.xlsx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Rec'd Requestor HQ, EMCBC or Direct Subject 11012 12-0004 12-001 12272011 192012 Alison D. MetzlerSullivan Papain Block McGrath & Cannovo P.C. DirectTransferred to Chicago...

  11. Job Logs & Statistics

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Software Policies User Surveys NERSC Users Group User Announcements Help Staff Blogs Request Repository Mailing List Operations for: Passwords & Off-Hours Status...

  12. Logging in to Hopper

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    it so that the applications run on the Hopper compute nodes. Accelerated X11 Performance NX is a freely available software package that greatly improves X11 performance over the...

  13. Logging in to Edison

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    so that the applications run on the Edison compute nodes. Accelerated X11 Performance NX is a freely available software package that greatly improves X11 performance over the...

  14. Recovery Efficiency Test Project: Phase 1, Activity report. Volume 1: Site selection, drill plan preparation, drilling, logging, and coring operations

    SciTech Connect (OSTI)

    Overbey, W.K. Jr.; Carden, R.S.; Kirr, J.N.

    1987-04-01

    The recovery Efficiency Test well project addressed a number of technical issues. The primary objective was to determine the increased efficiency gas recovery of a long horizontal wellbore over that of a vertical wellbore and, more specifically, what improvements can be expected from inducing multiple hydraulic fractures from such a wellbore. BDM corporation located, planned, and drilled a long radius turn horizontal well in the Devonian shale Lower Huron section in Wayne County, West Virginia, demonstrating that state-of-the-art technology is capable of drilling such wells. BDM successfully tested drilling, coring, and logging in a horizontal well using air as the circulating medium; conducted reservoir modeling studies to protect flow rates and reserves in advance of drilling operations; observed two phase flow conditions in the wellbore not observed previously; cored a fracture zone which produced gas; observed that fractures in the core and the wellbore were not systematically spaced (varied from 5 to 68 feet in different parts of the wellbore); observed that highest gas show rates reported by the mud logger corresponded to zone with lowest fracture spacing (five feet) or high fracture frequency. Four and one-half inch casting was successfully installed in the borehole and was equipped to isolate the horizontal section into eight (8) zones for future testing and stimulation operations. 6 refs., 48 figs., 10 tabs.

  15. Determination of Transport Properties From Flowing Fluid Temperature LoggingIn Unsaturated Fractured Rocks: Theory And Semi-Analytical Solution

    SciTech Connect (OSTI)

    Mukhopadhyay, Sumit; Tsang, Yvonne W.

    2008-08-01

    Flowing fluid temperature logging (FFTL) has been recently proposed as a method to locate flowing fractures. We argue that FFTL, backed up by data from high-precision distributed temperature sensors, can be a useful tool in locating flowing fractures and in estimating the transport properties of unsaturated fractured rocks. We have developed the theoretical background needed to analyze data from FFTL. In this paper, we present a simplified conceptualization of FFTL in unsaturated fractured rock, and develop a semianalytical solution for spatial and temporal variations of pressure and temperature inside a borehole in response to an applied perturbation (pumping of air from the borehole). We compare the semi-analytical solution with predictions from the TOUGH2 numerical simulator. Based on the semi-analytical solution, we propose a method to estimate the permeability of the fracture continuum surrounding the borehole. Using this proposed method, we estimated the effective fracture continuum permeability of the unsaturated rock hosting the Drift Scale Test (DST) at Yucca Mountain, Nevada. Our estimate compares well with previous independent estimates for fracture permeability of the DST host rock. The conceptual model of FFTL presented in this paper is based on the assumptions of single-phase flow, convection-only heat transfer, and negligible change in system state of the rock formation. In a sequel paper [Mukhopadhyay et al., 2008], we extend the conceptual model to evaluate some of these assumptions. We also perform inverse modeling of FFTL data to estimate, in addition to permeability, other transport parameters (such as porosity and thermal conductivity) of unsaturated fractured rocks.

  16. Spectral Analysis

    Energy Science and Technology Software Center (OSTI)

    2001-11-01

    SPEX enables the user to interactively create, display, compare, and analyze spectra (in particular gamma-ray spectra). It includes features from the INEEL GAUSS software series and the ORNL DAMM program. Input data is spectrum histograms, energy calibration, peakwidth calibrationb, and peak energy listgs. Output data includes new spectra created from projections, postscript for printing current view, summary log, gaussian fit log, exported energy calibratgion, exported peak lists and banana gates.

  17. IMPROVED V I log(gf) VALUES AND ABUNDANCE DETERMINATIONS IN THE PHOTOSPHERES OF THE SUN AND METAL-POOR STAR HD 84937

    SciTech Connect (OSTI)

    Lawler, J. E.; Wood, M. P.; Den Hartog, E. A.; Feigenson, T.; Sneden, C.; Cowan, J. J. E-mail: mpwood@wisc.edu E-mail: tfeigenson@wisc.edu E-mail: cowan@nhn.ou.edu

    2015-01-01

    New emission branching fraction measurements for 836 lines of the first spectrum of vanadium (V I) are determined from hollow cathode lamp spectra recorded with the National Solar Observatory 1 m Fourier transform spectrometer (FTS) and a high-resolution echelle spectrometer. The branching fractions are combined with recently published radiative lifetimes from laser-induced fluorescence measurements to determine accurate absolute atomic transition probabilities for the 836 lines. The FTS data are also used to extract new hyperfine structure A coefficients for 26 levels of neutral vanadium. These new laboratory data are applied to determine the V abundance in the Sun and metal-poor star HD 84937, yielding log ?(V) = 3.956 0.004 (? = 0.037) based on 93V I lines and log ?(V) = 1.89 0.03 (? = 0.07) based on nine V I lines, respectively, using the Holweger-Mller 1D model. These new V I abundance values for the Sun and HD 84937 agree well with our earlier determinations based upon V II.

  18. Parallel log structured file system collective buffering to achieve a compact representation of scientific and/or dimensional data

    DOE Patents [OSTI]

    Grider, Gary A.; Poole, Stephen W.

    2015-09-01

    Collective buffering and data pattern solutions are provided for storage, retrieval, and/or analysis of data in a collective parallel processing environment. For example, a method can be provided for data storage in a collective parallel processing environment. The method comprises receiving data to be written for a plurality of collective processes within a collective parallel processing environment, extracting a data pattern for the data to be written for the plurality of collective processes, generating a representation describing the data pattern, and saving the data and the representation.

  19. METALLICITIES, DUST, AND MOLECULAR CONTENT OF A QSO-DAMPED Ly{alpha} SYSTEM REACHING log N(H I) = 22: AN ANALOG TO GRB-DLAs

    SciTech Connect (OSTI)

    Guimaraes, R.; Noterdaeme, P.; Petitjean, P.; Ledoux, C.; Srianand, R.; Rahmani, H.; Lopez, S.

    2012-06-15

    We present the elemental abundance and H{sub 2} content measurements of a damped Ly{alpha} (DLA) system with an extremely large H I column density, log N(H I) (cm{sup -2}) = 22.0 {+-} 0.10, at z{sub abs} = 3.287 toward the QSO SDSS J081634+144612. We measure column densities of H{sub 2}, C I, C I*, Zn II, Fe II, Cr II, Ni II, and Si II from a high signal-to-noise and high spectral resolution VLT-UVES spectrum. The overall metallicity of the system is [Zn/H] = -1.10 {+-} 0.10 relative to solar. Two molecular hydrogen absorption components are seen at z = 3.28667 and 3.28742 (a velocity separation of Almost-Equal-To 52 km s{sup -1}) in rotational levels up to J = 3. We derive a total H{sub 2} column density of log N(H{sub 2}) (cm{sup -2}) = 18.66 and a mean molecular fraction of f = 2N(H{sub 2})/[2N(H{sub 2}) + N(H I)] = 10{sup -3.04{+-}0.37}, typical of known H{sub 2}-bearing DLA systems. From the observed abundance ratios we conclude that dust is present in the interstellar medium of this galaxy, with an enhanced abundance in the H{sub 2}-bearing clouds. However, the total amount of dust along the line of sight is not large and does not produce any significant reddening of the background QSO. The physical conditions in the H{sub 2}-bearing clouds are constrained directly from the column densities of H{sub 2} in different rotational levels, C I and C I*. The kinetic temperature is found to be T Almost-Equal-To 75 K and the particle density lies in the range n{sub H} = 50-80 cm{sup -3}. The neutral hydrogen column density of this DLA is similar to the mean H I column density of DLAs observed at the redshift of {gamma}-ray bursts (GRBs). We explore the relationship between GRB-DLAs and the high column density end of QSO-DLAs finding that the properties (metallicity and depletion) of DLAs with log N(H I) > 21.5 in the two populations do not appear to be significantly different.

  20. Geothermal Well Logging: Geological Wireline Logs and Fracture...

    Open Energy Info (EERE)

    Course on Geothermal Drilling, Resource Development and Power Plants; Santa Tecla, El Salvador; 20110116 Published Iceland GeoSurvey, 2011 DOI Not Provided Check for DOI...

  1. Interpretation of Flow Logs from Nevada Test Site Boreholes to Estimate Hydraulic conductivity Using Numerical Simulations Constrained by Single-Well Aquifer Tests

    SciTech Connect (OSTI)

    Garcia, C. Amanda; Halford, Keith J.; Laczniak, Randell J.

    2010-02-12

    Hydraulic conductivities of volcanic and carbonate lithologic units at the Nevada Test Site were estimated from flow logs and aquifer-test data. Borehole flow and drawdown were integrated and interpreted using a radial, axisymmetric flow model, AnalyzeHOLE. This integrated approach is used because complex well completions and heterogeneous aquifers and confining units produce vertical flow in the annular space and aquifers adjacent to the wellbore. AnalyzeHOLE simulates vertical flow, in addition to horizontal flow, which accounts for converging flow toward screen ends and diverging flow toward transmissive intervals. Simulated aquifers and confining units uniformly are subdivided by depth into intervals in which the hydraulic conductivity is estimated with the Parameter ESTimation (PEST) software. Between 50 and 150 hydraulic-conductivity parameters were estimated by minimizing weighted differences between simulated and measured flow and drawdown. Transmissivity estimates from single-well or multiple-well aquifer tests were used to constrain estimates of hydraulic conductivity. The distribution of hydraulic conductivity within each lithology had a minimum variance because estimates were constrained with Tikhonov regularization. AnalyzeHOLE simulated hydraulic-conductivity estimates for lithologic units across screened and cased intervals are as much as 100 times less than those estimated using proportional flow-log analyses applied across screened intervals only. Smaller estimates of hydraulic conductivity for individual lithologic units are simulated because sections of the unit behind cased intervals of the wellbore are not assumed to be impermeable, and therefore, can contribute flow to the wellbore. Simulated hydraulic-conductivity estimates vary by more than three orders of magnitude across a lithologic unit, indicating a high degree of heterogeneity in volcanic and carbonate-rock units. The higher water transmitting potential of carbonate-rock units relative to volcanic-rock units is exemplified by the large difference in their estimated maximum hydraulic conductivity; 4,000 and 400 feet per day, respectively. Simulated minimum estimates of hydraulic conductivity are inexact and represent the lower detection limit of the method. Minimum thicknesses of lithologic intervals also were defined for comparing AnalyzeHOLE results to hydraulic properties in regional ground-water flow models.

  2. Statistical Software for spatial analysis of stratigraphic data sets

    Energy Science and Technology Software Center (OSTI)

    2003-04-08

    Stratistics s a tool for statistical analysis of spatially explicit data sets and model output for description and for model-data comparisons. lt is intended for the analysis of data sets commonly used in geology, such as gamma ray logs and lithologic sequences, as well as 2-D data such as maps. Stratistics incorporates a far wider range of spatial analysis methods drawn from multiple disciplines, than are currently available in other packages. These include incorporation ofmore » techniques from spatial and landscape ecology, fractal analysis, and mathematical geology. Its use should substantially reduce the risk associated with the use of predictive models« less

  3. Gamma Log | Open Energy Information

    Open Energy Info (EERE)

    in mining, mineral exploration, water-well drilling, for formation evaluation in oil and gas well drilling and for other related purposes. Different types of rock emit different...

  4. FOIA_Log_2011.pdf

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

  5. Log in | The Ames Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Primary

  6. Request Log Closedl Date Yes

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    documents related to a survey, conducted by the Oak Ridge Institute for Science and Education in 1997. or certain building areas at the Engelhard1D.E. Uakepeace facility in...

  7. Trip Information Log Tracking System

    Energy Science and Technology Software Center (OSTI)

    1992-06-23

    The system is focused on the Employee Business Travel Event. The system must be able to CRUD (Create, Retrieve, Update, Delete) instances of the Travel Event as well as the ability to CRUD frequent flyer milage associated with airline travel. Additionally the system must provide for a compliance reporting system to monitor reductions in travel costs and lost opportunity costs (i.e., not taking advantage of business class or 7 day advance tickets).

  8. AVTA Federal Fleet PEV Readiness Data Logging and Characterization Study for the United States Forest Service: Caribou-Targhee National Forest

    SciTech Connect (OSTI)

    Stephen Schey; Jim Francfort; Ian Nienhueser

    2014-06-01

    Battelle Energy Alliance, LLC, managing and operating contractor for the U.S. Department of Energys Idaho National Laboratory, is the lead laboratory for U.S. Department of Energy Advanced Vehicle Testing. Battelle Energy Alliance, LLC contracted with Intertek Testing Services, North America (ITSNA) to collect and evaluate data on federal fleet operations as part of the Advanced Vehicle Testing Activitys Federal Fleet Vehicle Data Logging and Characterization study. The Advanced Vehicle Testing Activity study seeks to collect and evaluate data to validate the utilization of advanced electric drive vehicle transportation. This report focuses on the Caribou-Targhee National Forest (CTNF) fleet to identify daily operational characteristics of select vehicles and report findings on vehicle and mission characterizations to support the successful introduction of plug-in electric vehicles (PEVs) into the agencies fleets. Individual observations of these selected vehicles provide the basis for recommendations related to electric vehicle adoption and whether a battery electric vehicle (BEV) or plug-in hybrid electric vehicle (PHEV) (collectively plug-in electric vehicles, or PEVs) can fulfill the mission requirements. ITSNA acknowledges the support of Idaho National Laboratory and CTNF for participation in the study. ITSNA is pleased to provide this report and is encouraged by enthusiasm and support from the Forest Service and CTNF personnel.

  9. NREL: Energy Analysis - Manufacturing Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Energy Analysis Home Capabilities & Expertise Key Activities Analysis of Project Finance ... Supply Constraints Analysis Workforce Development Analysis Resource Assessment Models & ...

  10. SDSS/SEGUE spectral feature analysis for stellar atmospheric parameter estimation

    SciTech Connect (OSTI)

    Li, Xiangru; Lu, Yu; Yang, Tan; Wang, Yongjun; Wu, Q. M. Jonathan; Luo, Ali; Zhao, Yongheng; Zuo, Fang

    2014-08-01

    Large-scale and deep sky survey missions are rapidly collecting a large amount of stellar spectra, which necessitate the estimation of atmospheric parameters directly from spectra and make it feasible to statistically investigate latent principles in a large data set. We present a technique for estimating parameters T{sub eff}, log g, and [Fe/H] from stellar spectra. With this technique, we first extract features from stellar spectra using the LASSO algorithm; then, the parameters are estimated from the extracted features using the support vector regression. On a subsample of 20,000 stellar spectra from the Sloan Digital Sky Survey (SDSS) with reference parameters provided by the SDSS/SEGUE Spectroscopic Parameter Pipeline, estimation consistency are 0.007458 dex for log T{sub eff} (101.609921 K for T{sub eff}), 0.189557 dex for log g, and 0.182060 for [Fe/H], where the consistency is evaluated by mean absolute error. Prominent characteristics of the proposed scheme are sparseness, locality, and physical interpretability. In this work, each spectrum consists of 3821 fluxes, and 10, 19, and 14 typical wavelength positions are detected, respectively, for estimating T{sub eff}, log g, and [Fe/H]. It is shown that the positions are related to typical lines of stellar spectra. This characteristic is important in investigating physical indications from analysis results. Then, stellar spectra can be described by the individual fluxes on the detected positions (PD) or local integration of fluxes near them (LI). The aforementioned consistency is the result based on features described by LI. If features are described by PD, consistency is 0.009092 dex for log T{sub eff} (124.545075 K for T{sub eff}), 0.198928 dex for log g, and 0.206814 dex for [Fe/H].

  11. Petrophysical Analysis and Geographic Information System for San Juan Basin Tight Gas Reservoirs

    SciTech Connect (OSTI)

    Martha Cather; Robert Lee; Robert Balch; Tom Engler; Roger Ruan; Shaojie Ma

    2008-10-01

    The primary goal of this project is to increase the availability and ease of access to critical data on the Mesaverde and Dakota tight gas reservoirs of the San Juan Basin. Secondary goals include tuning well log interpretations through integration of core, water chemistry and production analysis data to help identify bypassed pay zones; increased knowledge of permeability ratios and how they affect well drainage and thus infill drilling plans; improved time-depth correlations through regional mapping of sonic logs; and improved understanding of the variability of formation waters within the basin through spatial analysis of water chemistry data. The project will collect, integrate, and analyze a variety of petrophysical and well data concerning the Mesaverde and Dakota reservoirs of the San Juan Basin, with particular emphasis on data available in the areas defined as tight gas areas for purpose of FERC. A relational, geo-referenced database (a geographic information system, or GIS) will be created to archive this data. The information will be analyzed using neural networks, kriging, and other statistical interpolation/extrapolation techniques to fine-tune regional well log interpretations, improve pay zone recognition from old logs or cased-hole logs, determine permeability ratios, and also to analyze water chemistries and compatibilities within the study area. This single-phase project will be accomplished through four major tasks: Data Collection, Data Integration, Data Analysis, and User Interface Design. Data will be extracted from existing databases as well as paper records, then cleaned and integrated into a single GIS database. Once the data warehouse is built, several methods of data analysis will be used both to improve pay zone recognition in single wells, and to extrapolate a variety of petrophysical properties on a regional basis. A user interface will provide tools to make the data and results of the study accessible and useful. The final deliverable for this project will be a web-based GIS providing data, interpretations, and user tools that will be accessible to anyone with Internet access. During this project, the following work has been performed: (1) Assimilation of most special core analysis data into a GIS database; (2) Inventorying of additional data, such as log images or LAS files that may exist for this area; (3) Analysis of geographic distribution of that data to pinpoint regional gaps in coverage; (4) Assessment of the data within both public and proprietary data sets to begin tuning of regional well logging analyses and improve payzone recognition; (5) Development of an integrated web and GIS interface for all the information collected in this effort, including data from northwest New Mexico; (6) Acquisition and digitization of logs to create LAS files for a subset of the wells in the special core analysis data set; and (7) Petrophysical analysis of the final set of well logs.

  12. Partially penetrating fractures: Pressure transient analysis of an infinite conductivity fracture

    SciTech Connect (OSTI)

    Rodriguez, F.; Cinco-Ley, H.; Horne, R.N.

    1984-04-01

    The effect of the partial penetration of an infinite conductivity fracture on the transient pressure behavior of a vertically fractured well is investigated. Analysis of results shows that the pressure behavior of a well intersected by a partially-penetrating infinite conductivity vertical fracture can be divided into three flow periods: 1) the early time flow period which is characterized by a formation linear flow as in the case of a fully-penetrating infinite-conductivity vertical fracture, 2) the infinite-acting flow period and 3) the pseudoradial flow period which develops after the effects of the vertical boundaries of the reservoir are felt in the pressure behavior of the well. A log-log graph of log(h /SUB f/ /h)p /SUB wD/ versus log t /SUB Dxf/ shows a slope of one half during the early time flow period of a well with an infinite-conductivity partially penetrating fracture. The time for the end of the early time flow period is directly related to the square of the dimensionless height of the fracture, h /SUB fD/, which is defined as the ratio between the height of the fracture and its half length.

  13. Subsurface basin analysis of fault-controlled turbidite system in Bradano trough, southern Adriatic foredeep, Italy

    SciTech Connect (OSTI)

    Casnedi, R.

    1988-11-01

    Subsurface data (seismic lines, wireline logs, cores, and drill cuttings) from intensive hydrocarbon exploration in the Pliocene-Pleistocene Bradano Trough were used in performing a three-dimensional basin analysis and in reconstructing the time-space evolution of the basin. A middle Pliocene sedimentary system characterizes the hydrocarbon-bearing sands of the major gas field of the Bradano Trough, the Candela field. This system includes two phases of deposition in a migrating basin. 9 figures.

  14. CILC Studies with Comparative Analysis to Existing Plants L2.MPO.P7.06

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    CILC Studies with Comparative Analysis to Existing Plants L2.MPO.P7.06 BRIAN KENDRICK Los Alamos National Laboratory VICTOR PETROV DANIEL WALTER ANNALISA MANERA University of Michigan CASL-U-2013-0 -000 CASL-U-2013-0224-000 L2.MPO.P7.06 ii REVISION LOG Revision Date Affected Pages Revision Description 0 09/30/2013 All Initial Issuance Document pages that are: Export Controlled ________________ ___________________________________ IP/Proprietary/NDA Controlled _____

  15. IMPROVED Ni I log(gf) VALUES AND ABUNDANCE DETERMINATIONS IN THE PHOTOSPHERES OF THE SUN AND METAL-POOR STAR HD 84937

    SciTech Connect (OSTI)

    Wood, M. P.; Lawler, J. E.; Sneden, C.; Cowan, J. J. E-mail: jelawler@wisc.edu E-mail: cowan@nhn.ou.edu

    2014-04-01

    Atomic transition probability measurements for 371 Ni I lines in the UV through near-IR are reported. Branching fractions from data recorded using a Fourier transform spectrometer and a new echelle spectrograph are combined with published radiative lifetimes to determine these transition probabilities. Generally good agreement is found in comparisons to previously reported Ni I transition probability measurements. Use of the new echelle spectrograph, independent radiometric calibration methods, and independent data analysis routines enable a reduction of systematic errors and overall improvement in transition probability uncertainty over previous measurements. The new Ni I data are applied to high-resolution visible and UV spectra of the Sun and metal-poor star HD 84937 to derive new, more accurate Ni abundances. Lines covering a wide range of wavelength and excitation potential are used to search for non-LTE effects.

  16. IMPROVED Ti II log(gf) VALUES AND ABUNDANCE DETERMINATIONS IN THE PHOTOSPHERES OF THE SUN AND METAL-POOR STAR HD 84937

    SciTech Connect (OSTI)

    Wood, M. P.; Lawler, J. E.; Sneden, C.; Cowan, J. J. E-mail: jelawler@wisc.edu E-mail: cowan@nhn.ou.edu

    2013-10-01

    Atomic transition probability measurements for 364 lines of Ti II in the UV through near-IR are reported. Branching fractions from data recorded using a Fourier transform spectrometer (FTS) and a new echelle spectrometer are combined with published radiative lifetimes to determine these transition probabilities. The new results are in generally good agreement with previously reported FTS measurements. Use of the new echelle spectrometer, independent radiometric calibration methods, and independent data analysis routines enables a reduction of systematic errors and overall improvement in transition probability accuracy over previous measurements. The new Ti II data are applied to high-resolution visible and UV spectra of the Sun and metal-poor star HD 84937 to derive new, more accurate Ti abundances. Lines covering a range of wavelength and excitation potential are used to search for non-LTE effects. The Ti abundances derived using Ti II for these two stars match those derived using Ti I and support the relative Ti/Fe abundance ratio versus metallicity seen in previous studies.

  17. SUPPLEMENT ANALYSIS

    Energy Savers [EERE]

    812 Supplement Analysis 1 October 2013 SUPPLEMENT ANALYSIS for the FINAL ENVIRONMENTAL ASSESSMENT for NECO (FORMERLY HAXTUN) WIND ENERGY PROJECT LOGAN AND PHILLIPS COUNTIES, COLORADO U. S. Department of Energy Office of Energy Efficiency and Renewable Energy Golden Field Office and U.S. Department of Energy Western Area Power Administration Rocky Mountain Customer Service Region OCTOBER 2013 DOE/EA-1812/SA-1 DOE/EA-1812 Supplement Analysis 2 October 2013 SUPPLEMENT ANALYSIS for the FINAL

  18. Pressure Temperature Log | Open Energy Information

    Open Energy Info (EERE)

    to reach equilibrium with the surrounding formation is going to provide the most accurate reservoir temperature (Blackwell, et al., 2010). Potential Pitfalls Fluids are being...

  19. Connect & Log In | Argonne Leadership Computing Facility

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Unauthorized or improper use of this system may result in administrative disciplinary action and civil and criminal penalties. By continuing to use this system you indicate...

  20. Microsoft Word - FOIA Log FY 2003.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    to scope of work, and the like Yes 12403 003 11503 12203 Direct Requested that you forward to this office your latest organizational chart, andor staff directory at your...

  1. Uncertainty Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Analysis - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion ...

  2. NREL: Energy Analysis - Market Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Market Analysis The laboratory's market analysis helps increase the use of renewable energy (RE) and energy efficiency (EE) technologies in the marketplace by providing strategic information to stakeholders interested in rapidly changing electricity markets. Our high-quality and objective crosscutting assessments and analysis support informed decision making. Primary focuses include: Energy Technology/Program Cost, Performance, and Market Data The Office of Energy Efficiency and Renewable Energy

  3. Program Analysis

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and abate nearly 20,000 mmt of CO2 through 2050. EE portfolio analysis wNEMS+MARKAL (Frances Wood, OnLocation, and Chip Friley, BNL) Heavily leverages ANL's Autonomie Tool...

  4. Supplement Analysis

    Energy Savers [EERE]

    Supplement Analysis to the LCLS-ll Environmental Assessment, July. 2014 U.S. DEPARTMENT OF Office of *ENERGY 1 Science SLAG Site Office SLAC National Accelerator Laboratory 2575 Sand Hill Road, MS-8A Menlo Park, CA 94025 DATE: September 15, 2015 MEMORANDUM FOR: Paul Golan, Site Manager, SLAC Site Office THROUGH: James Elmore, ISC-OR NEPA Compliance Officer, Oak Ridge Office FROM: Mitzi Heard, NEPA Coornator, SLAC Site Office SUBJECT: Supplement Analysis to SLAC LCLS-I1 Environmental Assessment.

  5. NREL: Energy Analysis - Sustainability Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Sustainability Analysis The laboratory's Sustainability Analysis looks at the environmental, life-cycle, climate, and other impacts of renewable energy technologies. Our energy choices have global implications that affect greenhouse gas emissions, water resource distribution, mineral consumption, and equipment manufacturing and transportation. The school of thought is that renewable energy technologies are more sustainable than many current sources of energy. However, we need to verify that this

  6. Seismic analysis applied to the delimiting of a gas reservoir

    SciTech Connect (OSTI)

    Ronquillo, G.; Navarro, M.; Lozada, M.; Tafolla, C.

    1996-08-01

    We present the results of correlating seismic models with petrophysical parameters and well logs to mark the limits of a gas reservoir in sand lenses. To fulfill the objectives of the study, we used a data processing sequence that included wavelet manipulation, complex trace attributes and pseudovelocities inversion, along with several quality control schemes to insure proper amplitude preservation. Based on the analysis and interpretation of the seismic sections, several areas of interest were selected to apply additional signal treatment as preconditioning for petrophysical inversion. Signal classification was performed to control the amplitudes along the horizons of interest, and to be able to find an indirect interpretation of lithologies. Additionally, seismic modeling was done to support the results obtained and to help integrate the interpretation. The study proved to be a good auxiliary tool in the location of the probable extension of the gas reservoir in sand lenses.

  7. Nonparametric Multivariate Anomaly Analysis in Support of HPC Resilience

    SciTech Connect (OSTI)

    Ostrouchov, George; Naughton, III, Thomas J; Engelmann, Christian; Vallee, Geoffroy R; Scott, Stephen L

    2009-01-01

    Large-scale computing systems provide great potential for scientific exploration. However, the complexity that accompanies these enormous machines raises challeges for both, users and operators. The effective use of such systems is often hampered by failures encountered when running applications on systems containing tens-of-thousands of nodes and hundreds-of-thousands of compute cores capable of yielding petaflops of performance. In systems of this size failure detection is complicated and root-cause diagnosis difficult. This paper describes our recent work in the identification of anomalies in monitoring data and system logs to provide further insights into machine status, runtime behavior, failure modes and failure root causes. It discusses the details of an initial prototype that gathers the data and uses statistical techniques for analysis.

  8. Analysis Repository

    SciTech Connect (OSTI)

    DOE

    2012-03-16

    The Analysis Repository is a compilation of analyses and analytical models relevant to assessing hydrogen fuel and fuel cell issues. Projects in the repository relate to: hydrogen production, delivery, storage, fuel cells, and hydrogen vehicle technology; hydrogen production feedstock cost and availability; electricity production, central and distributed; energy resource estimation and forecasting.

  9. Energy Market Analysis

    Broader source: Energy.gov [DOE]

    Energy Market Analysis synthesizes all analysis efforts in the analysis spectrum. Scenario analyses, in the context of market analysis, are used to answer several questions:

  10. Financial Analysis

    Energy Science and Technology Software Center (OSTI)

    2010-12-31

    This tool takes into account the net cost savings, implementation costs, and operations and maintenance costs of an energy conservation measure, as well as typical project lifetime and the relating discount and escalation rates. The result is a cash flow analysis over the project lifetime with calculations for simple payback, discounted payback, net present value, and savings to investment ratio. The tool also displays the results graphically.

  11. Uncertainty Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Analysis - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Fuel Cycle Defense Waste Management Programs Advanced Nuclear Energy

  12. Polyculture Analysis

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Polyculture Analysis 24 March 2015 Deborah Newby, Ph.D. Idaho National Laboratory This presentation does not contain any proprietary, confidential, or otherwise restricted information Algal Feedstocks DOE Bioenergy Technologies Office (BETO) 2015 Project Peer Review Hub -- Sandia National Laboratories Oak Ridge National Laboratory Pacific Northwest National Laboratory 2 | Bioenergy Technologies Office Goal Statement (Hub) Challenge: * To contribute to meeting the Renewable Fuel Standard, DOE

  13. systems analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    systems analysis - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Fuel Cycle Defense Waste Management Programs Advanced Nuclear

  14. Microalgae Analysis

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Microalgae Analysis March 24, 2015 Algal Feedstocks Review Mark Wigmosta Pacific Northwest National Laboratory This presentation does not contain any proprietary, confidential, or otherwise restricted information Goal: Enable Economically Feasible and Sustainable Algal Biofuels to Achieve Advanced Biofuel Targets Key challenge: "A national assessment of land requirements for algae cultivation that takes into account climatic conditions; fresh water, inland and coastal saline water, and

  15. Petrofacies analysis - the petrophysical tool for geologic/engineering reservoir characterization

    SciTech Connect (OSTI)

    Watney, W.L.; Guy, W.J.; Gerlach, P.M.

    1997-08-01

    Petrofacies analysis is defined as the characterization and classification of pore types and fluid saturations as revealed by petrophysical measures of a reservoir. The word {open_quotes}petrofacies{close_quotes} makes an explicit link between petroleum engineers concerns with pore characteristics as arbiters of production performance, and the facies paradigm of geologists as a methodology for genetic understanding and prediction. In petrofacies analysis, the porosity and resistivity axes of the classical Pickett plot are used to map water saturation, bulk volume water, and estimated permeability, as well as capillary pressure information, where it is available. When data points are connected in order of depth within a reservoir, the characteristic patterns reflect reservoir rock character and its interplay with the hydrocarbon column. A third variable can be presented at each point on the crossplot by assigning a color scale that is based on other well logs, often gamma ray or photoelectric effect, or other derived variables. Contrasts between reservoir pore types and fluid saturations will be reflected in changing patterns on the crossplot and can help discriminate and characterize reservoir heterogeneity. Many hundreds of analyses of well logs facilitated by spreadsheet and object-oriented programming have provided the means to distinguish patterns typical of certain complex pore types for sandstones and carbonate reservoirs, occurrences of irreducible water saturation, and presence of transition zones. The result has been an improved means to evaluate potential production such as bypassed pay behind pipe and in old exploration holes, or to assess zonation and continuity of the reservoir. Petrofacies analysis is applied in this example to distinguishing flow units including discrimination of pore type as assessment of reservoir conformance and continuity. The analysis is facilitated through the use of color cross sections and cluster analysis.

  16. AnalyzeHOLE: An Integrated Wellbore Flow Analysis Tool

    SciTech Connect (OSTI)

    Keith J. Halford

    2009-10-01

    Conventional interpretation of flow logs assumes that hydraulic conductivity is directly proportional to flow change with depth. However, well construction can significantly alter the expected relation between changes in fluid velocity and hydraulic conductivity. Strong hydraulic conductivity contrasts between lithologic intervals can be masked in continuously screened wells. Alternating intervals of screen and blank casing also can greatly complicate the relation between flow and hydraulic properties. More permeable units are not necessarily associated with rapid fluid-velocity increases. Thin, highly permeable units can be misinterpreted as thick and less permeable intervals or not identified at all. These conditions compromise standard flow-log interpretation because vertical flow fields are induced near the wellbore. AnalyzeHOLE, an integrated wellbore analysis tool for simulating flow and transport in wells and aquifer systems, provides a better alternative for simulating and evaluating complex well-aquifer system interaction. A pumping well and adjacent aquifer system are simulated with an axisymmetric, radial geometry in a two-dimensional MODFLOW model. Hydraulic conductivities are distributed by depth and estimated with PEST by minimizing squared differences between simulated and measured flows and drawdowns. Hydraulic conductivity can vary within a lithology but variance is limited with regularization. Transmissivity of the simulated system also can be constrained to estimates from single-well, pumping tests. Water-quality changes in the pumping well are simulated with simple mixing models between zones of differing water quality. These zones are differentiated by backtracking thousands of particles from the well screens with MODPATH. An Excel spreadsheet is used to interface the various components of AnalyzeHOLE by (1) creating model input files, (2) executing MODFLOW, MODPATH, PEST, and supporting FORTRAN routines, and (3) importing and graphically displaying pertinent results.

  17. Resource Analysis | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Resource Analysis Technological Feasibility & Cost Analysis Environmental Analysis Delivery Analysis Infrastructure Development & Financial Analysis Energy Market Analysis DOE H2A ...

  18. Economic Analysis of Policy Effects Analysis Platform

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Economic Analysis of Policy Effects Analysis Platform March 24, 2015 Jason Hansen, PhD ... * Annual Milestone (93015): Identify economic benefits of co- products on biorefinery ...

  19. Petrophysical evaluation of subterranean formations

    DOE Patents [OSTI]

    Klein, James D; Schoderbek, David A; Mailloux, Jason M

    2013-05-28

    Methods and systems are provided for evaluating petrophysical properties of subterranean formations and comprehensively evaluating hydrate presence through a combination of computer-implemented log modeling and analysis. Certain embodiments include the steps of running a number of logging tools in a wellbore to obtain a variety of wellbore data and logs, and evaluating and modeling the log data to ascertain various petrophysical properties. Examples of suitable logging techniques that may be used in combination with the present invention include, but are not limited to, sonic logs, electrical resistivity logs, gamma ray logs, neutron porosity logs, density logs, NRM logs, or any combination or subset thereof.

  20. Role of Analysis

    Broader source: Energy.gov [DOE]

    Presentation on the role of analysis to the DOE Systems Analysis Workshop held in Washington, D.C. July 28-29, 2004 to discuss and define role of systems analysis in DOE Hydrogen Program.

  1. Stability analysis of self-similar behaviors in perfect fluid gravitational collapse

    SciTech Connect (OSTI)

    Mitsuda, Eiji; Tomimatsu, Akira

    2006-06-15

    Stability of self-similar solutions for gravitational collapse is an important problem to be investigated from the perspectives of their nature as an attractor, critical phenomena, and instability of a naked singularity. In this paper we study spherically symmetric non-self-similar perturbations of matter and metrics in spherically symmetric self-similar backgrounds. The collapsing matter is assumed to be a perfect fluid with the equation of state P={alpha}{rho}. We construct a single wave equation governing the perturbations, which makes their time evolution in arbitrary self-similar backgrounds analytically tractable. Further we propose an analytical application of this master wave equation to the stability problem by means of the normal mode analysis for the perturbations having the time dependence given by exp(i{omega}log vertical t vertical bar), and present some sufficient conditions for the absence of nonoscillatory unstable normal modes with purely imaginary {omega}.

  2. Planning, Budget, and Analysis

    Broader source: Energy.gov [DOE]

    Presentation on Planning, Budget, and Analysis to the DOE Systems Analysis Workshop held in Washington, D.C. July 28-29, 2004.

  3. Analysis Methodologies | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Systems Analysis » Analysis Methodologies Analysis Methodologies A spectrum of analysis methodologies are used in combination to provide a sound understanding of hydrogen and fuel cell systems and developing markets, as follows: Resource Analysis Technological Feasibility and Cost Analysis Environmental Analysis Delivery Analysis Infrastructure Development and Financial Analysis Energy Market Analysis In general, each methodology builds on previous efforts to quantify the benefits, drawbacks,

  4. Advanced Multivariate Analysis Tools Applied to Surface Analysis...

    Office of Scientific and Technical Information (OSTI)

    Advanced Multivariate Analysis Tools Applied to Surface Analysis. Citation Details In-Document Search Title: Advanced Multivariate Analysis Tools Applied to Surface Analysis. No...

  5. NREL: Energy Analysis - Solar Technology Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Solar Technology Analysis NREL conducts analysis to support research and development done by the Solar Energy Technologies Program in three major technology areas: concentrating solar power; solar electricity, also known as photovoltaics or PV; and solar heating and lighting. For example, in the area of photovoltaics, EERE's systems modeling and analysis activity rigorously assesses the performance, reliability, installed costs, and levelized energy costs (LECs) of a wide variety of flat-plate

  6. NREL: Energy Analysis - Wind Technology Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Wind and Hydropower Technology Analysis Wind and hydropower analysis supports advanced technologies that convert more of the nation's wind into electricity. Grid Operational Impact Analysis The wind program will address the variable, normally uncontrollable nature of wind power plant output, and the additional needs that its operation imposes on the overall grid. At present, the generation and transmission operational impacts that occur due to wind variability are not well quantified. This

  7. K Basin Hazard Analysis

    SciTech Connect (OSTI)

    PECH, S.H.

    2000-08-23

    This report describes the methodology used in conducting the K Basins Hazard Analysis, which provides the foundation for the K Basins Final Safety Analysis Report. This hazard analysis was performed in accordance with guidance provided by DOE-STD-3009-94, Preparation Guide for U. S. Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports and implements the requirements of DOE Order 5480.23, Nuclear Safety Analysis Report.

  8. K Basins Hazard Analysis

    SciTech Connect (OSTI)

    WEBB, R.H.

    1999-12-29

    This report describes the methodology used in conducting the K Basins Hazard Analysis, which provides the foundation for the K Basins Safety Analysis Report (HNF-SD-WM-SAR-062, Rev.4). This hazard analysis was performed in accordance with guidance provided by DOE-STD-3009-94, Preparation Guide for U. S. Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports and implements the requirements of DOE Order 5480.23, Nuclear Safety Analysis Report.

  9. Fluid Inclusion Analysis At Coso Geothermal Area (2004-2005)...

    Open Energy Info (EERE)

    and much fine scale detail when the logs are analyzed in detail. References Dilley, L. M.; Norman, D.I.; Berard, B. (1 January 2004) FLUID INCLUSION STRATIGRAPHY: NEW METHOD...

  10. Core Analysis At Fort Bliss Area (Combs, Et Al., 1999) | Open...

    Open Energy Info (EERE)

    well. A suite of geophysical logs (gamma ray, neutron, sonic, and resistivity) was also run tier completion of drilling. References Jim Combs, John T. Finger, Colin Goranson,...

  11. Pressure Temperature Log At Roosevelt Hot Springs Geothermal...

    Open Energy Info (EERE)

    Unknown Exploration Basis Faulder 1991 Conceptual Geological Model compilation and literature review of the Roosevelt Hot Springs Geothermal Area. Notes Pre-exploitation...

  12. Pressure Temperature Log At Valles Caldera - Redondo Geothermal...

    Open Energy Info (EERE)

    New Mexico (VC-1) Jamie N. Gardner, Fraser E. Goff, Sue Goff, Larry Maassen, K. Mathews, Daniel Wachs, D. Wilson (1987) Core Lithology, Valles Caldera No. 1, New Mexico...

  13. Neutron Log At Valles Caldera - Redondo Geothermal Area (Rowley...

    Open Energy Info (EERE)

    New Mexico (VC-1) Jamie N. Gardner, Fraser E. Goff, Sue Goff, Larry Maassen, K. Mathews, Daniel Wachs, D. Wilson (1987) Core Lithology, Valles Caldera No. 1, New Mexico...

  14. Caliper Log At Valles Caldera - Redondo Geothermal Area (Rowley...

    Open Energy Info (EERE)

    New Mexico (VC-1) Jamie N. Gardner, Fraser E. Goff, Sue Goff, Larry Maassen, K. Mathews, Daniel Wachs, D. Wilson (1987) Core Lithology, Valles Caldera No. 1, New Mexico...

  15. Gamma Log At Valles Caldera - Redondo Geothermal Area (Rowley...

    Open Energy Info (EERE)

    New Mexico (VC-1) Jamie N. Gardner, Fraser E. Goff, Sue Goff, Larry Maassen, K. Mathews, Daniel Wachs, D. Wilson (1987) Core Lithology, Valles Caldera No. 1, New Mexico...

  16. Resistivity Log At Valles Caldera - Redondo Geothermal Area ...

    Open Energy Info (EERE)

    New Mexico (VC-1) Jamie N. Gardner, Fraser E. Goff, Sue Goff, Larry Maassen, K. Mathews, Daniel Wachs, D. Wilson (1987) Core Lithology, Valles Caldera No. 1, New Mexico...

  17. Acoustic Logs At Steamboat Springs Area (Combs, Et Al., 1999...

    Open Energy Info (EERE)

    acoustic borehole televiewer (BHTV) yielded wellbore images down to 520';and a Sandia memory tool gave pressuretemperature data for a shut-in test at the end of the project....

  18. Acoustic Logs At Newberry Caldera Area (Combs, Et Al., 1999)...

    Open Energy Info (EERE)

    more improvements DOE-funding Unknown Notes The acoustic borehole televiewer (BHTV) was run twice in the wellbore with limited success. There were several problems with the tool's...

  19. Pressure Temperature Log At Chena Geothermal Area (Holdmann,...

    Open Energy Info (EERE)

    during the GRED III Phase I exploration program. References Gwen Holdmann, Dick Benoit, David Blackwell (2006) Integrated Geoscience Investigation and Geothermal Exploration at...

  20. Uniduto Log stica S A UNIDUTO | Open Energy Information

    Open Energy Info (EERE)

    the development, construction and operation of an ethanol pipeline network linking the port terminal on the coast of Sao Paulo state and the city of Paulinia. References: Uniduto...

  1. Pressure Temperature Log At Steamboat Springs Area (Combs, Et...

    Open Energy Info (EERE)

    normal test. If this effect is not compensated, heating the electronics will cause the signal output to drift, giving unreliable data. A properly cahbrated tool accounts for the...

  2. Manager's Signature Log Privacy Impact Assessment, Office of...

    Energy Savers [EERE]

    PIA - Tour Tracker Energy Employees' Occupational Illness Compensation Program Act (EEOICPA) Tracking Database, INL Energy Employees' Occupational Illness Compensation Program...

  3. Electric Micro Imager Log At Coso Geothermal Area (2003) | Open...

    Open Energy Info (EERE)

    be corrected for well-bore deviation. References Rose, P.; Barton, C.; McCulloch, J.; Moore, J.N.; Kovac, K.; Sheridan, J.; Spielman, P.; Berard, B. (1 January 2003) The Coso EGS...

  4. Resistivity Log At Alum Area (Moos & Ronne, 2010) | Open Energy...

    Open Energy Info (EERE)

    and Cross-Well Resistivity Activity Date Usefulness useful DOE-funding Unknown Notes Density and electrical resistivity data were important to calibrate structural models based...

  5. Well Log Data At Valles Caldera - Redondo Geothermal Area (Shevenell...

    Open Energy Info (EERE)

    extending to the AET-4 well near Jemez Springs. References Lisa Shevenell, Fraser E. Goff, Dan Miles, Al Waibel, Chandler Swanberg (1988) Lithologic Descriptions and Temperature...

  6. Chicago Office Manager's Signature Log Privacy Impact Assessment

    Energy Savers [EERE]

  7. Resistivity Log At Valles Caldera - Sulphur Springs Geothermal...

    Open Energy Info (EERE)

    presents a good target for surface geophysical prospecting. References Michael Wilt, Stephen Vonder Haar (1986) A Geological And Geophysical Appraisal Of The Baca Geothermal...

  8. Cross-Dipole Acoustic Log | Open Energy Information

    Open Energy Info (EERE)

    Sonic Imager Internet. 2013. cited 20131010. Available from: http:www.slb.comservicescharacterizationgeomechanicswirelinedipoleshearsonicimager.aspx ...

  9. Resistivity Log At Long Valley Caldera Geothermal Area (Nordquist...

    Open Energy Info (EERE)

    Volcanic Complex: A Preliminary Magnetotelluric and Magnetic Variation Interpretation Philip E. Wannamaker, P.M. Wright, Zhou Zi-xing, Li Xing-bin, Zhao Jing-xiang (1991)...

  10. Gamma Log At Lightning Dock Geothermal Area (Witcher, 2006) ...

    Open Energy Info (EERE)

    Usefulness useful DOE-funding Unknown Exploration Basis Part of the Geothermal Resource Evaluation and Definition (GRED) Program administered by DOE-AAO under Cooperative...

  11. d+d Fusions with Log-normal Model

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    MacKenzie Warrens 1 Cryo-cooled gas mixture of D 2 + 3 He was released from the gas jet 90-180J pulse from the Texas Pettawatt Laser irradiated the D 2 clusters Coulomb...

  12. Descriptive logs, skeletonized samples, and photographs of core...

    Open Energy Info (EERE)

    skeletonized samples, and photographs of core from Presco Energy's thermal gradient wells P3-1, P10-1, and P32-2 in the Rye Patch area, Pershing County, Nevada Jump to:...

  13. Systems Analysis Workshop Purpose

    Broader source: Energy.gov [DOE]

    Presentation on SAW purpose to the DOE Systems Analysis Workshop held in Washington, D.C. July 28-29, 2004 to discuss and define role of systems analysis in DOE Hydrogen Program.

  14. Office of Analysis

    Broader source: Energy.gov [DOE]

    The Office of Analysis provides analysis of Department of Energy (DOE)-wide performance in protecting the public, the workers and the environment while performing the missions of DOE.

  15. Systems Analysis Workshop Agenda

    Broader source: Energy.gov [DOE]

    Agenda from DOE Systems Analysis Workshop held in Washington, D.C. July 28-29, 2004 to discuss and define role of systems analysis in DOE Hydrogen Program.

  16. NETL: SOFC Systems Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Systems Analysis NETL possesses strong systems analysis and policy support capabilities. Systems analysis support of the SOFC Program consists of conducting various energy analyses that provide input to decisions on issues such as national plans and programs, resource use, environmental and energy security policies, technology options for R&D programs and pathways to the commercialization and deployment of SOFC power systems. Here is a partial listing of SOFC systems analysis:

  17. Modeling & Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    A view upwind of SWIS' aerosol-generating system. Permalink Gallery Sandia Wake-Imaging System Successfully Deployed at Scaled Wind Farm Technology Facility Analysis, Capabilities, Energy, Facilities, Modeling, Modeling, Modeling & Analysis, Modeling & Analysis, News, News & Events, Partnership, Renewable Energy, Research & Capabilities, SWIFT, Systems Analysis, Technical Highlights, Wind Energy, Wind News Sandia Wake-Imaging System Successfully Deployed at Scaled Wind Farm

  18. Sensitivity and Uncertainty Analysis

    Broader source: Energy.gov [DOE]

    Summary Notes from 15 November 2007 Generic Technical Issue Discussion on Sensitivity and Uncertainty Analysis and Model Support

  19. NREL: Energy Analysis - Technology Systems Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Technology Systems Analysis NREL's Technology Systems Analysis examines RD&D areas in terms of potential costs, benefits, risks, uncertainties, and timeframes. The following pages provide information on specific technology areas: Biomass Building Electric Infrastructure Systems Energy Sciences Geothermal Hydrogen and Fuel Cells Solar Vehicles and Fuels Research Wind Key staff analyst Summary bios of staff expertise and interests Team Lead: Margaret Mann Administrative Support: Catherine

  20. NREL: Energy Analysis - Biomass Technology Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Biomass Technology Analysis Conducting full life-cycle assessments for biomass products, including electricity, biodiesel, and ethanol, is important for determining environmental benefits. NREL analysts use a life-cycle inventory modeling package and supporting databases to conduct life-cycle assessments. These tools can be applied on a global, regional, local, or project basis. Integrated system analyses, technoeconomic analyses, life-cycle assessments (LCAs), and other analysis tools are

  1. NREL: Energy Analysis - Building Technologies Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Building Technologies Analysis The Building Technologies analysis supports research and development on technologies and practices for energy efficiency, working closely with the building industry and manufacturers; promotes energy and money-saving opportunities to builders and consumers; and works with state and local regulatory groups to improve building codes and appliance standards. Building Energy Software Tools Directory Described here are 283 energy-related software tools for buildings,

  2. Economic Analysis of Policy Effects Analysis Platform

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Economic Analysis of Policy Effects Analysis Platform March 24, 2015 Jason Hansen, PhD Idaho National Laboratory This presentation does not contain any proprietary, confidential, or otherwise restricted information DOE Bioenergy Technologies Office (BETO) 2015 Project Peer Review 4.1.2.20 2 | Bioenergy Technologies Office * The goal of this project is to 1) identify risk factors in the biofuel supply system, 2) translate risk factors to implications, and 3) identify strategies and polices to

  3. Static downhole characteristics of well CGEH-1 at Coso Hot Springs...

    Open Energy Info (EERE)

    Geothermal Exploration Activities Activities (5) Acoustic Logs At Coso Geothermal Area (1977) Cuttings Analysis At Coso Geothermal Area (1977) Gamma Log At Coso Geothermal Area...

  4. Sustainability & Strategic Analysis

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Kristen Johnson Technology Manager Bioenergy Technologies Office Peer Review March 23, 2015 Sustainability & Strategic Analysis 2 | Bioenergy Technologies Office * The Team * Goals & Objectives * Challenges * Approach & Partnerships * Budget * Key Accomplishments * Future Directions * Upcoming Activities Introduction: Analysis & Sustainability (A&S) 3 | Bioenergy Technologies Office Introductions: Analysis & Sustainability Staff Alison Goss Eng Alicia Lindauer Zia Haq

  5. The Tariff Analysis Project: A Database and Analysis Platform...

    Open Energy Info (EERE)

    Tariff Analysis Project: A Database and Analysis Platform for Electricity Tariffs Jump to: navigation, search Tool Summary LAUNCH TOOL Name: The Tariff Analysis Project: A Database...

  6. Delivery Analysis | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Systems Analysis » Analysis Methodologies » Delivery Analysis Delivery Analysis Delivery Analysis identifies the most economic options for delivering hydrogen, and provides a foundation for additional research on alternative storage and transportation options. Additionally, delivery analysis provides crucial information to technology feasibility analysis, in determining the optimal production capacities and locations. Delivery analyses will be conducted to determine the most promising

  7. Infrastructure Development and Financial Analysis | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Resource Analysis Technological Feasibility & Cost Analysis Environmental Analysis Delivery Analysis Infrastructure Development & Financial Analysis Energy Market Analysis DOE H2A ...

  8. ENHANCED UNCERTAINTY ANALYSIS FOR SRS COMPOSITE ANALYSIS

    SciTech Connect (OSTI)

    Smith, F.; Phifer, M.

    2011-06-30

    The Composite Analysis (CA) performed for the Savannah River Site (SRS) in 2009 (SRS CA 2009) included a simplified uncertainty analysis. The uncertainty analysis in the CA (Smith et al. 2009b) was limited to considering at most five sources in a separate uncertainty calculation performed for each POA. To perform the uncertainty calculations in a reasonable amount of time, the analysis was limited to using 400 realizations, 2,000 years of simulated transport time, and the time steps used for the uncertainty analysis were increased from what was used in the CA base case analysis. As part of the CA maintenance plan, the Savannah River National Laboratory (SRNL) committed to improving the CA uncertainty/sensitivity analysis. The previous uncertainty analysis was constrained by the standard GoldSim licensing which limits the user to running at most four Monte Carlo uncertainty calculations (also called realizations) simultaneously. Some of the limitations on the number of realizations that could be practically run and the simulation time steps were removed by building a cluster of three HP Proliant windows servers with a total of 36 64-bit processors and by licensing the GoldSim DP-Plus distributed processing software. This allowed running as many as 35 realizations simultaneously (one processor is reserved as a master process that controls running the realizations). These enhancements to SRNL computing capabilities made uncertainty analysis: using 1000 realizations, using the time steps employed in the base case CA calculations, with more sources, and simulating radionuclide transport for 10,000 years feasible. In addition, an importance screening analysis was performed to identify the class of stochastic variables that have the most significant impact on model uncertainty. This analysis ran the uncertainty model separately testing the response to variations in the following five sets of model parameters: (a) K{sub d} values (72 parameters for the 36 CA elements in sand and clay), (b) Dose Parameters (34 parameters), (c) Material Properties (20 parameters), (d) Surface Water Flows (6 parameters), and (e) Vadose and Aquifer Flow (4 parameters). Results provided an assessment of which group of parameters is most significant in the dose uncertainty. It was found that K{sub d} and the vadose/aquifer flow parameters, both of which impact transport timing, had the greatest impact on dose uncertainty. Dose parameters had an intermediate level of impact while material properties and surface water flows had little impact on dose uncertainty. Results of the importance analysis are discussed further in Section 7 of this report. The objectives of this work were to address comments received during the CA review on the uncertainty analysis and to demonstrate an improved methodology for CA uncertainty calculations as part of CA maintenance. This report partially addresses the LFRG Review Team issue of producing an enhanced CA sensitivity and uncertainty analysis. This is described in Table 1-1 which provides specific responses to pertinent CA maintenance items extracted from Section 11 of the SRS CA (2009). As noted above, the original uncertainty analysis looked at each POA separately and only included the effects from at most five sources giving the highest peak doses at each POA. Only 17 of the 152 CA sources were used in the original uncertainty analysis and the simulation time was reduced from 10,000 to 2,000 years. A major constraint on the original uncertainty analysis was the limitation of only being able to use at most four distributed processes. This work expanded the analysis to 10,000 years using 39 of the CA sources, included cumulative dose effects at downstream POAs, with more realizations (1,000) and finer time steps. This was accomplished by using the GoldSim DP-Plus module and the 36 processors available on a new windows cluster. The last part of the work looked at the contribution to overall uncertainty from the main categories of uncertainty variables: K{sub d}s, dose parameters, flow parameters, and material propertie

  9. NREL: Energy Analysis - Jenny Heeter

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Market analysis Policy analysis Utility regulation and analysis Primary research interests Voluntary green power market Renewable energy certificate markets and pricing Solar ...

  10. Chemical Sector Analysis | NISAC

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NISACChemical Sector Analysis content top Chemical Supply Chain Analysis Posted by Admin on Mar 1, 2012 in | Comments 0 comments Chemical Supply Chain Analysis NISAC has developed a range of capabilities for analyzing the consequences of disruptions to the chemical manufacturing industry. Each capability provides a different but complementary perspective on the questions of interest-questions like Given an event, will the entire chemical sector be impacted or just parts? Which chemicals, plants,

  11. Decision Analysis for EGS

    Broader source: Energy.gov [DOE]

    Project objectives: DEVELOPMENT OF ANALYSIS TOOLS TO ASSESS: Uncertainties associated with exploration for EGS; Uncertainties associated with development of EGS; Uncertainties associated with operation of EGS.

  12. Asset Protection Analysis Guide

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2008-08-21

    The Guide provides examples of the application of as set protection analysis to several common problems. Canceled by DOE N 251.80.

  13. Sandia Energy - Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Climate Change Is the Subject of a New Book Analysis, Climate, Global Climate & Energy, Monitoring, News, News & Events, Sensing, Sensing & Monitoring, Water Security Climate...

  14. Performance Analysis with Vampir

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    (frank.winkler@tu-dresden.de) Performance Analysis with Vampir Disclaimer Performance tools will not automatically make you code run faster. They help you understand, what your...

  15. Independent Statistics & Analysis

    U.S. Energy Information Administration (EIA) Indexed Site

    October 2014 Independent Statistics & Analysis www.eia.gov U.S. Department of Energy Washington, DC 20585 Quarterly Coal Distribution Report April - June 2014 This report was...

  16. Modeling and Analysis

    Broader source: Energy.gov [DOE]

    DOE modeling and analysis activities focus on reducing uncertainties and improving transparency in photovoltaics (PV) and concentrating solar power (CSP) performance modeling. The overall goal of...

  17. Automated Hazard Analysis

    Energy Science and Technology Software Center (OSTI)

    2003-06-26

    The Automated Hazard Analysis (AHA) application is a software tool used to conduct job hazard screening and analysis of tasks to be performed in Savannah River Site facilities. The AHA application provides a systematic approach to the assessment of safety and environmental hazards associated with specific tasks, and the identification of controls regulations, and other requirements needed to perform those tasks safely. AHA is to be integrated into existing Savannah River site work control andmore » job hazard analysis processes. Utilization of AHA will improve the consistency and completeness of hazard screening and analysis, and increase the effectiveness of the work planning process.« less

  18. Fast Analysis and Simulation Team | NISAC

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NISACFast Analysis and Simulation Team

  19. K Basin safety analysis

    SciTech Connect (OSTI)

    Porten, D.R.; Crowe, R.D.

    1994-12-16

    The purpose of this accident safety analysis is to document in detail, analyses whose results were reported in summary form in the K Basins Safety Analysis Report WHC-SD-SNF-SAR-001. The safety analysis addressed the potential for release of radioactive and non-radioactive hazardous material located in the K Basins and their supporting facilities. The safety analysis covers the hazards associated with normal K Basin fuel storage and handling operations, fuel encapsulation, sludge encapsulation, and canister clean-up and disposal. After a review of the Criticality Safety Evaluation of the K Basin activities, the following postulated events were evaluated: Crane failure and casks dropped into loadout pit; Design basis earthquake; Hypothetical loss of basin water accident analysis; Combustion of uranium fuel following dryout; Crane failure and cask dropped onto floor of transfer area; Spent ion exchange shipment for burial; Hydrogen deflagration in ion exchange modules and filters; Release of Chlorine; Power availability and reliability; and Ashfall.

  20. NREL: Energy Analysis - Energy Analysis Newsletter

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Decision Insight and Market Impacts Newsletter Unsubscribe Please enter your email address to unsubscribe from the Decision Insight and Market Impacts Newsletter. Complete E-mail Address: Unsubscribe If you have any questions about this online subscription service, please contact us. Printable Version Energy Analysis Home Capabilities & Expertise Key Activities Models & Tools Data & Resources Publications Partnerships Staff Working with Us Related Links News Did you find what you

  1. NREL: Energy Analysis - Energy Sciences Technology Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Energy Sciences Technology Analysis To help meet the nation's needs for clean energy, inexpensive alternative fuels, and a healthy environment, researchers in NREL's Energy Sciences are improving our understanding of the science behind renewable energy and energy-efficient technologies. These technologies include photovoltaics (solar cells), fuels and energy systems made from biomass (plants and waste products) and hydrogen, and advanced energy storage and transmission systems. In this work, our

  2. NREL: Energy Analysis - Geothermal Technology Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Geothermal Technology Analysis The Department of Energy's (DOE) Geothermal Energy Program focuses in three areas: energy systems research and testing (working to enhance conversion of geothermal energy into heat and electricity) led by NREL; drilling technologies research (for both hardware and diagnostic tools) led by Sandia National Laboratories; and geoscience and supporting technologies research (exploration and resource management) led by the Idaho National Engineering and Environmental

  3. Hazard Analysis Database Report

    SciTech Connect (OSTI)

    GAULT, G.W.

    1999-10-13

    The Hazard Analysis Database was developed in conjunction with the hazard analysis activities conducted in accordance with DOE-STD-3009-94, Preparation Guide for US Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports, for the Tank Waste Remediation System (TWRS) Final Safety Analysis Report (FSAR). The FSAR is part of the approved TWRS Authorization Basis (AB). This document describes, identifies, and defines the contents and structure of the TWRS FSAR Hazard Analysis Database and documents the configuration control changes made to the database. The TWRS Hazard Analysis Database contains the collection of information generated during the initial hazard evaluations and the subsequent hazard and accident analysis activities. The database supports the preparation of Chapters 3,4, and 5 of the TWRS FSAR and the USQ process and consists of two major, interrelated data sets: (1) Hazard Evaluation Database--Data from the results of the hazard evaluations; and (2) Hazard Topography Database--Data from the system familiarization and hazard identification.

  4. Graphical Contingency Analysis Tool

    Energy Science and Technology Software Center (OSTI)

    2010-03-02

    GCA is a visual analytic tool for power grid contingency analysis to provide more decision support for power grid operations. GCA allows power grid operators to quickly gain situational awareness of power grid by converting large amounts of operational data to graphic domain with a color contoured map; identify system trend and foresee and discern emergencies by performing trending analysis; identify the relationships between system configurations and affected assets by conducting clustering analysis; and identifymore » the best action by interactively evaluate candidate actions.« less

  5. Demand Response Analysis Tool

    SciTech Connect (OSTI)

    2012-03-01

    Demand Response Analysis Tool is a software developed at the Lawrence Berkeley National Laboratory. It is initially funded by Southern California Edison. Our goal in developing this tool is to provide an online, useable, with standardized methods, an analysis tool to evaluate demand and demand response performance of commercial and industrial facilities. The tool provides load variability and weather sensitivity analysis capabilities as well as development of various types of baselines. It can be used by researchers, real estate management firms, utilities, or any individuals who are interested in analyzing their demand and demand response capabilities.

  6. Demand Response Analysis Tool

    Energy Science and Technology Software Center (OSTI)

    2012-03-01

    Demand Response Analysis Tool is a software developed at the Lawrence Berkeley National Laboratory. It is initially funded by Southern California Edison. Our goal in developing this tool is to provide an online, useable, with standardized methods, an analysis tool to evaluate demand and demand response performance of commercial and industrial facilities. The tool provides load variability and weather sensitivity analysis capabilities as well as development of various types of baselines. It can be usedmore » by researchers, real estate management firms, utilities, or any individuals who are interested in analyzing their demand and demand response capabilities.« less

  7. Contributed Review: Nuclear magnetic resonance core analysis at 0.3 T

    SciTech Connect (OSTI)

    Mitchell, Jonathan Fordham, Edmund J.

    2014-11-15

    Nuclear magnetic resonance (NMR) provides a powerful toolbox for petrophysical characterization of reservoir core plugs and fluids in the laboratory. Previously, there has been considerable focus on low field magnet technology for well log calibration. Now there is renewed interest in the study of reservoir samples using stronger magnets to complement these standard NMR measurements. Here, the capabilities of an imaging magnet with a field strength of 0.3 T (corresponding to 12.9 MHz for proton) are reviewed in the context of reservoir core analysis. Quantitative estimates of porosity (saturation) and pore size distributions are obtained under favorable conditions (e.g., in carbonates), with the added advantage of multidimensional imaging, detection of lower gyromagnetic ratio nuclei, and short probe recovery times that make the system suitable for shale studies. Intermediate field instruments provide quantitative porosity maps of rock plugs that cannot be obtained using high field medical scanners due to the field-dependent susceptibility contrast in the porous medium. Example data are presented that highlight the potential applications of an intermediate field imaging instrument as a complement to low field instruments in core analysis and for materials science studies in general.

  8. Geotechnical Analysis Report for July 1999-June 2000

    SciTech Connect (OSTI)

    Westinghouse TRU Solutions

    2002-10-01

    This Geotechnical Analysis Report (GAR) presents and interprets the geotechnical data from the underground excavations at the Waste Isolation Pilot Plant (WIPP). The data, which are obtained as part of a regular monitoring program, are used to characterize conditions, to compare actual performance to the design assumptions, and to evaluate and forecast the performance of the underground excavations during operations. GARs have been available to the public since 1983. During the Site and Preliminary Design Validation (SPDV) Program, the architect/engineer for the project produced these reports on a quarterly basis to document the geomechanical performance during and immediately after excavation of the underground facility. Since the completion of the construction phase of the project in 1987, the management and operating contractor for the facility has prepared these reports annually. This report describes the performance and condition of selected areas from July 1, 1999, to June 30, 2000. It is divided into ten chapters. The remainder of Chapter 1 provides background information on the WIPP, its mission, and the purpose and scope of the geomechanical monitoring program. Chapter 2 describes the local and regional geology of the WIPP site. Chapters 3 and 4 describe the geomechanical instrumentation located in the shafts and shaft stations, present the data collected by that instrumentation, and provide interpretation of these data. Chapters 5, 6, and 7 present the results of geomechanical monitoring in the three main portions of the WIPP underground facility (the access drifts, the Northern Experimental Area, and the Waste Disposal Area). Chapter 8 discusses the results of the Geoscience Program, which includes fracture mapping, borehole logging, and borehole observations. Chapter 9 provides an assessment of the hydrologic conditions near the Exhaust Shaft. Chapter 10 summarizes the results of the geomechanical monitoring and compares the current excavation performance to the design requirements.

  9. Geotechnical Analysis Report for July 2000-June 2001

    SciTech Connect (OSTI)

    Westinghouse TRU Solutions

    2002-09-26

    This Geotechnical Analysis Report (GAR) presents and interprets the geotechnical data from the underground excavations at the Waste Isolation Pilot Plant (WIPP). The data, which are obtained as part of a regular monitoring program, are used to characterize conditions, to compare actual performance to the design assumptions, and to evaluate and forecast the performance of the underground excavations during operations. GARs have been available to the public since 1983. During the Site and Preliminary Design Validation (SPDV) Program, the architect/engineer for the project produced these reports on a quarterly basis to document the geomechanical performance during and immediately after excavation of the underground facility. Since the completion of the construction phase of the project in 1987, the management and operating contractor for the facility has prepared these reports annually. This report describes the performance and condition of selected areas from July 1, 2000, to June 30, 2001. It is divided into ten chapters. The remainder of Chapter 1 provides background information on WIPP, its mission, and the purpose and scope of the geomechanical monitoring program. Chapter 2 describes the local and regional geology of the WIPP site. Chapters 3 and 4 describe the geomechanical instrumentation located in the shafts and shaft stations, present the data collected by that instrumentation, and provide interpretation of these data. Chapters 5, 6, and 7 present the results of geomechanical monitoring in the three main portions of the WIPP underground facility (the access drifts, the Northern Experimental Area, and the Waste Disposal Area). Chapter 8 discusses the results of the Geoscience Program, which include fracture and stratigraphic mapping, borehole and core logging, and borehole observations. Chapter 9 provides an assessment of the hydrologic conditions near the Exhaust Shaft. Chapter 10 summarizes the results of the geomechanical monitoring and compares the current excavation performance to the design requirements.

  10. Geotechnical Analysis Report for July 2001 - June 2002

    SciTech Connect (OSTI)

    Washington TRU Solutions LLC

    2002-09-20

    This Geotechnical Analysis Report (GAR) presents and interprets the geotechnical data from the underground excavations at the Waste Isolation Pilot Plant (WIPP). The data, which are obtained as part of a regular monitoring program, are used to characterize conditions, to compare actual performance to the design assumptions, and to evaluate and forecast the performance of the underground excavations. GARs have been available to the public since 1983. During the Site and Preliminary Design Validation (SPDV) Program, the architect/engineer for the project produced these reports on a quarterly basis to document the geomechanical performance during and immediately after excavation of the underground facility. Since the completion of the construction phase of the project in 1987, the management and operating contractor for the facility has prepared these reports annually. This report describes the performance and condition of selected areas from July 1, 2001, to June 30, 2002. It is divided into ten chapters. The remainder of Chapter 1 provides background information on WIPP, its mission, and the purpose and scope of the geomechanical monitoring program. Chapter 2 describes the local and regional geology of the WIPP site. Chapters 3 and 4 describe the geomechanical instrumentation located in the shafts and shaft stations, present the data collected by that instrumentation, and provide interpretation of these data. Chapters 5, 6, and 7 present the results of geomechanical monitoring in the three main portions of the WIPP underground facility (the access drifts, the Northern Experimental Area, and the Waste Disposal Area). Chapter 8 discusses the results of the Geoscience Program, which include fracture and stratigraphic mapping, borehole and core logging, and borehole observations. Chapter 9 summarizes the results of the geomechanical monitoring and compares the current excavation performance to the design requirements. Chapter 10 lists the References and Bibliography.

  11. Geotechnical Analysis Report for July 1998-June 1999

    SciTech Connect (OSTI)

    Westinghouse

    2002-08-29

    This Geotechnical Analysis Report (GAR) presents and interprets the geotechnical data from the underground excavations at the Waste Isolation Pilot Plant (WIPP). The data, which are obtained as part of a regular monitoring program, are used to characterize conditions, to compare actual performance to the design assumptions, and to evaluate and forecast the performance of the underground excavations during operations. GARs have been available to the public since 1983. During the Site and Preliminary Design Validation (SPDV) Program, the architect/engineer for the project produced these reports on a quarterly basis to document the geomechanical performance during and immediately after excavation of the underground facility. Since the completion of the construction phase of the project in 1987, the management and operating contractor for the facility has prepared these reports annually. This report describes the performance and condition of selected areas from July 1, 1998, to June 30, 1999. It is divided into nine chapters. The remainder of Chapter 1.0 provides background information on the WIPP, its mission, and the purpose and scope of the geomechanical monitoring program. Chapter 2.0 describes the local and regional geology of the WIPP site. Chapters 3.0 and 4.0 describe the geomechanical instrumentation located in the shafts and shaft stations, present the data collected by that instrumentation, and provide interpretation of these data. Chapters 5.0, 6.0, and 7.0 present the results of geomechanical monitoring in the three main portions of the WIPP underground facility (the access drifts, the Northern Experimental Area, and the Waste Disposal Area). Chapter 8.0 discusses the results of the Geoscience Program, which includes fracture mapping, borehole logging, and borehole observations. Chapter 9.0 summarizes the results of the geomechanical monitoring and compares the current excavation performance to the design requirements.

  12. Hydrogen Analysis | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Analysis Hydrogen Analysis Presentation on Hydrogen Analysis to the DOE Systems Analysis Workshop held in Washington, D.C. July 28-29, 2004 to discuss and define role of systems analysis in DOE Hydrogen Program. PDF icon 6_h2a_mann.pdf More Documents & Publications H2A Delivery Models and Results H2A Delivery Components Model and Analysis Hydrogen Delivery Analysis Plus Meeting: DTT, STT, HPTT, Other Analysts, Invited Guests

  13. Energy Analysis | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Services » Energy Analysis Energy Analysis Photo courtesy of Dennis Schroeder, NREL 24348 Photo courtesy of Dennis Schroeder, NREL 24348 Energy analysis informs EERE decision-making by delivering analytical products in four main areas: Data Resources, Market Intelligence, Energy Systems Analysis, and Portfolio Impacts Analysis. The Energy Analysis website is designed to help energy experts and policymakers access energy analysis resources related to renewable energy and energy efficiency. It

  14. Fluid Inclusion Gas Analysis

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Dilley, Lorie

    2013-01-01

    Fluid inclusion gas analysis for wells in various geothermal areas. Analyses used in developing fluid inclusion stratigraphy for wells and defining fluids across the geothermal fields. Each sample has mass spectrum counts for 180 chemical species.

  15. Building America Analysis Spreadsheets

    Broader source: Energy.gov [DOE]

    The Building America Analysis Spreadsheets are companions to the House Simulation Protocols, and can assist with many of the calculations and look-up tables found in the report. The spreadsheets...

  16. Energy Sector Market Analysis

    SciTech Connect (OSTI)

    Arent, D.; Benioff, R.; Mosey, G.; Bird, L.; Brown, J.; Brown, E.; Vimmerstedt, L.; Aabakken, J.; Parks, K.; Lapsa, M.; Davis, S.; Olszewski, M.; Cox, D.; McElhaney, K.; Hadley, S.; Hostick, D.; Nicholls, A.; McDonald, S.; Holloman, B.

    2006-10-01

    This paper presents the results of energy market analysis sponsored by the Department of Energy's (DOE) Weatherization and International Program (WIP) within the Office of Energy Efficiency and Renewable Energy (EERE). The analysis was conducted by a team of DOE laboratory experts from the National Renewable Energy Laboratory (NREL), Oak Ridge National Laboratory (ORNL), and Pacific Northwest National Laboratory (PNNL), with additional input from Lawrence Berkeley National Laboratory (LBNL). The analysis was structured to identify those markets and niches where government can create the biggest impact by informing management decisions in the private and public sectors. The analysis identifies those markets and niches where opportunities exist for increasing energy efficiency and renewable energy use.

  17. Systems Analysis Sub site

    SciTech Connect (OSTI)

    EERE

    2012-03-16

    Systems analysis provides direction, focus, and support for the development and introduction of hydrogen production, storage, and end-use technologies, and provides a basis for recommendations on a balanced portfolio of activities.

  18. Fluid Inclusion Gas Analysis

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Dilley, Lorie

    Fluid inclusion gas analysis for wells in various geothermal areas. Analyses used in developing fluid inclusion stratigraphy for wells and defining fluids across the geothermal fields. Each sample has mass spectrum counts for 180 chemical species.

  19. Supervisory Program Analysis Officer

    Broader source: Energy.gov [DOE]

    A successful candidate in this position will be responsible for the program analysis and evaluation of all activities which fall within the purview of the Office. The incumbent directs a moderate...

  20. NREL: Energy Analysis - Publications

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Analysis The front cover of the Reimagining What's Possible brochure. PDF 3.6 MB Making Sustainable Energy Choices: Insights on the EnergyWater Land Nexus The front cover of...

  1. Performance Measurement Analysis System

    Energy Science and Technology Software Center (OSTI)

    1989-06-01

    The PMAS4.0 (Performance Measurement Analysis System) is a user-oriented system designed to track the cost and schedule performance of Department of Energy (DOE) major projects (MPs) and major system acquisitions (MSAs) reporting under DOE Order 5700.4A, Project Management System. PMAS4.0 provides for the analysis of performance measurement data produced from management control systems complying with the Federal Government''s Cost and Schedule Control Systems Criteria.

  2. NREL Sustainability Analysis

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Date: March 25, 2015 Technology Area: Sustainability PIs: Daniel Inman and Garvin Heath Organization: National Renewable Energy Laboratory This presentation does not contain any proprietary, confidential, or otherwise restricted information. NREL Sustainability Analysis WBS 4.2.1.30 2 Goal - Air Emissions from Bioenergy Systems NREL's sustainability analysis program aims to better understand air emissions from the biofuel supply chain, applicable air regulations and implications for cost,

  3. Interactive Comparative Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Comparative Analysis Interactive Comparative Analysis We can learn the correlations between sensors and modalities that differentiate activities (or operating modes) by using transfer learning. Our new approach to data fusion and signature discovery has a number of advantages and applications: * Finding correlations that differentiate datasets requires less data than finding correlations that explain datasets. * The differences between datasets are smaller in number, and often easier to

  4. Hurricane Irene Analysis | NISAC

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    SheetsHurricane Irene Analysis content top Hurricane Irene Analysis Hurricane Irene was the only 2011 hurricane to make a U.S. landfall. As Irene neared landfall, NISAC modeled the hurricane's potential impacts on critical infrastructure in several key sectors located in the projected storm track. This provided situational awareness and advanced warning of potential infrastructure impacts for DHS and Federal Emergency Management Agency (FEMA) leadership and personnel on the ground, both federal

  5. Modeling & Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    SunShot Grand Challenge: Regional Test Centers Modeling & Analysis Home/Tag:Modeling & Analysis - Electricity use by water service sector and county. Shown are electricity use by (a) large-scale conveyance, (b) groundwater irrigation pumping, (c) surface water irrigation pumping, (d) drinking water, and (e) wastewater. Aggregate electricity use across these sectors (f) is also mapped. Permalink Gallery Sandians Recognized in Environmental Science & Technology's Best Paper

  6. Strategic Analysis and Modeling

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    NREL is a national laboratory of the U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, operated by the Alliance for Sustainable Energy, LLC. Strategic Analysis and Modeling Mary J. Biddy, Ling Tao, Eric Tan, Yimin Zhang National Renewable Energy Laboratory March 24, 2015 Analysis and Sustainability Peer Review 2015 DOE Bioenergy Technologies Office (BETO) Project Peer Review 2 Goal Statement * Develop tools and perform analyses to address key questions in support of

  7. DOE Retro Analysis Plan

    Office of Environmental Management (EM)

    Retro Analysis Plan August 2, 2011 Page 1 August 2, 2011 Daniel Cohen, Esq. Office of General Counsel U.S. Department of Energy 1000 Independence Avenue, SW Washington, DC 20585 Re: Preliminary Plan for Retrospective Analysis Dear Mr. Cohen: These comments are submitted by the Air-Conditioning, Heating, and Refrigeration Institute (AHRI) in response to the U.S. Department of Energy's (DOE) notice appearing in the July 11, 2011 Federal Register requesting comments on the Preliminary Plan for

  8. Analysis | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Analysis Analysis The Bioenergy Technologies Office uses a wide range of analytical tools, data, and methodologies to support decision making, guide research, and demonstrate progress toward goals. The wide variety of available biomass feedstocks, conversion technologies, and integration strategies offer a broad range of feasible biofuels scenarios, so the Office focuses its analytical activities on the biofuels research and development (R&D) pathways that offer the best potential for

  9. TIME DELAY AND ACCRETION DISK SIZE MEASUREMENTS IN THE LENSED QUASAR SBS 0909+532 FROM MULTIWAVELENGTH MICROLENSING ANALYSIS

    SciTech Connect (OSTI)

    Hainline, Laura J.; Morgan, Christopher W.; MacLeod, Chelsea L.; Landaal, Zachary D. [Department of Physics, United States Naval Academy, 572C Holloway Rd, Annapolis, MD 21402 (United States); Kochanek, C. S. [Department of Astronomy, The Ohio State University, 140 West 18th Ave, Columbus, OH 43210 (United States); Harris, Hugh C.; Tilleman, Trudy [United States Naval Observatory, Flagstaff Station, 10391 West Naval Observatory Road, Flagstaff, AZ 86001-8521 (United States); Goicoechea, L. J.; Shalyapin, V. N. [Facultad de Ciencias, Universidad de Cantabria, Avda. de Los Castros s/n, E-39005 Santander (Spain); Falco, Emilio E., E-mail: hainline@usna.edu, E-mail: cmorgan@usna.edu, E-mail: macleod@usna.edu, E-mail: m123894@usna.edu, E-mail: ckochanek@astronomy.ohio-state.edu, E-mail: hch@nofs.navy.mil, E-mail: trudy@nofs.navy.mil, E-mail: goicol@unican.es, E-mail: vshal@ukr.net, E-mail: falco@cfa.harvard.edu [Harvard-Smithsonian Center for Astrophysics, 60 Garden St, Cambridge, MA 02138 (United States)

    2013-09-01

    We present three complete seasons and two half-seasons of Sloan Digital Sky Survey (SDSS) r-band photometry of the gravitationally lensed quasar SBS 0909+532 from the U.S. Naval Observatory, as well as two seasons each of SDSS g-band and r-band monitoring from the Liverpool Robotic Telescope. Using Monte Carlo simulations to simultaneously measure the system's time delay and model the r-band microlensing variability, we confirm and significantly refine the precision of the system's time delay to {Delta}t{sub AB} = 50{sub -4}{sup +2} days, where the stated uncertainties represent the bounds of the formal 1{sigma} confidence interval. There may be a conflict between the time delay measurement and a lens consisting of a single galaxy. While models based on the Hubble Space Telescope astrometry and a relatively compact stellar distribution can reproduce the observed delay, the models have somewhat less dark matter than we would typically expect. We also carry out a joint analysis of the microlensing variability in the r and g bands to constrain the size of the quasar's continuum source at these wavelengths, obtaining log {l_brace}(r{sub s,r}/cm)[cos i/0.5]{sup 1/2}{r_brace} = 15.3 {+-} 0.3 and log {l_brace}(r{sub s,g}/cm)[cos i/0.5]{sup 1/2}{r_brace} = 14.8 {+-} 0.9, respectively. Our current results do not formally constrain the temperature profile of the accretion disk but are consistent with the expectations of standard thin disk theory.

  10. Analysis of Critical Permeabilty, Capillary Pressure and Electrical Properties for Mesaverde Tight Gas Sandstones from Western U.S. Basins

    SciTech Connect (OSTI)

    Alan Byrnes; Robert Cluff; John Webb; John Victorine; Ken Stalder; Daniel Osburn; Andrew Knoderer; Owen Metheny; Troy Hommertzheim; Joshua Byrnes; Daniel Krygowski; Stefani Whittaker

    2008-06-30

    Although prediction of future natural gas supply is complicated by uncertainty in such variables as demand, liquefied natural gas supply price and availability, coalbed methane and gas shale development rate, and pipeline availability, all U.S. Energy Information Administration gas supply estimates to date have predicted that Unconventional gas sources will be the dominant source of U.S. natural gas supply for at least the next two decades (Fig. 1.1; the period of estimation). Among the Unconventional gas supply sources, Tight Gas Sandstones (TGS) will represent 50-70% of the Unconventional gas supply in this time period (Fig. 1.2). Rocky Mountain TGS are estimated to be approximately 70% of the total TGS resource base (USEIA, 2005) and the Mesaverde Group (Mesaverde) sandstones represent the principal gas productive sandstone unit in the largest Western U.S. TGS basins including the basins that are the focus of this study (Washakie, Uinta, Piceance, northern Greater Green River, Wind River, Powder River). Industry assessment of the regional gas resource, projection of future gas supply, and exploration programs require an understanding of reservoir properties and accurate tools for formation evaluation. The goal of this study is to provide petrophysical formation evaluation tools related to relative permeability, capillary pressure, electrical properties and algorithms for wireline log analysis. Detailed and accurate moveable gas-in-place resource assessment is most critical in marginal gas plays and there is need for quantitative tools for definition of limits on gas producibility due to technology and rock physics and for defining water saturation. The results of this study address fundamental questions concerning: (1) gas storage; (2) gas flow; (3) capillary pressure; (4) electrical properties; (5) facies and upscaling issues; (6) wireline log interpretation algorithms; and (7) providing a web-accessible database of advanced rock properties. The following text briefly discusses the nature of these questions. Section I.2 briefly discusses the objective of the study with respect to the problems reviewed.

  11. Sandia Energy - PV Modeling & Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    PV Modeling & Analysis Home Stationary Power Energy Conversion Efficiency Solar Energy Photovoltaics PV Modeling & Analysis PV Modeling & AnalysisTara Camacho-Lopez2015-05-11T20:03...

  12. Production, Storage, and FC Analysis

    Broader source: Energy.gov [DOE]

    Presentation on Production, Storage, and FC Analysis to the DOE Systems Analysis Workshop held in Washington, D.C. July 28-29, 2004 to discuss and define role of systems analysis in DOE Hydrogen Program.

  13. Systems Analysis | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    About the Geothermal Technologies Office » Systems Analysis Systems Analysis What is the Systems Analysis program? The Systems Analysis program in the Geothermal Technologies Office focuses primarily on: Environmental issues Policy, regulatory, and financing Economic Analysis and validation Data and Tools that support geothermal exploration and development As a key part of the Systems Analysis portfolio, a two-year, comprehensive Vision Study for geothermal energy development is underway to

  14. Compression Algorithm Analysis of In-Situ (S)TEM Video: Towards Automatic Event Detection and Characterization

    SciTech Connect (OSTI)

    Teuton, Jeremy R.; Griswold, Richard L.; Mehdi, Beata L.; Browning, Nigel D.

    2015-09-23

    Precise analysis of both (S)TEM images and video are time and labor intensive processes. As an example, determining when crystal growth and shrinkage occurs during the dynamic process of Li dendrite deposition and stripping involves manually scanning through each frame in the video to extract a specific set of frames/images. For large numbers of images, this process can be very time consuming, so a fast and accurate automated method is desirable. Given this need, we developed software that uses analysis of video compression statistics for detecting and characterizing events in large data sets. This software works by converting the data into a series of images which it compresses into an MPEG-2 video using the open source avconv utility [1]. The software does not use the video itself, but rather analyzes the video statistics from the first pass of the video encoding that avconv records in the log file. This file contains statistics for each frame of the video including the frame quality, intra-texture and predicted texture bits, forward and backward motion vector resolution, among others. In all, avconv records 15 statistics for each frame. By combining different statistics, we have been able to detect events in various types of data. We have developed an interactive tool for exploring the data and the statistics that aids the analyst in selecting useful statistics for each analysis. Going forward, an algorithm for detecting and possibly describing events automatically can be written based on statistic(s) for each data type.

  15. Advanced engineering analysis

    SciTech Connect (OSTI)

    Freeman, W.R.

    1992-11-01

    The Advanced Engineering Analysis project is being used to improve the breadth of engineering analysis types, the particular phenomena which may be simulated, and also increase the accuracy and usability of the results of both new and current types of simulations and analyses. This is an interim report covering several topics under this project. Information on two new implementations of failure criteria for metal forming, the implementation of coupled fluid flow/heat transfer analysis capabilities, the integration of experimental shock and vibration test data with analyses, a correction to a contact solution problem with a 3-D parabolic brick finite element, and the development and implementation of a file translator to link IDEAS to DYNA3D is provided in this report.

  16. Contamination analysis unit

    DOE Patents [OSTI]

    Gregg, Hugh R. (Livermore, CA); Meltzer, Michael P. (Livermore, CA)

    1996-01-01

    The portable Contamination Analysis Unit (CAU) measures trace quantifies of surface contamination in real time. The detector head of the portable contamination analysis unit has an opening with an O-ring seal, one or more vacuum valves and a small mass spectrometer. With the valve closed, the mass spectrometer is evacuated with one or more pumps. The O-ring seal is placed against a surface to be tested and the vacuum valve is opened. Data is collected from the mass spectrometer and a portable computer provides contamination analysis. The CAU can be used to decontaminate and decommission hazardous and radioactive surface by measuring residual hazardous surface contamination, such as tritium and trace organics It provides surface contamination data for research and development applications as well as real-time process control feedback for industrial cleaning operations and can be used to determine the readiness of a surface to accept bonding or coatings.

  17. Contamination analysis unit

    DOE Patents [OSTI]

    Gregg, H.R.; Meltzer, M.P.

    1996-05-28

    The portable Contamination Analysis Unit (CAU) measures trace quantities of surface contamination in real time. The detector head of the portable contamination analysis unit has an opening with an O-ring seal, one or more vacuum valves and a small mass spectrometer. With the valve closed, the mass spectrometer is evacuated with one or more pumps. The O-ring seal is placed against a surface to be tested and the vacuum valve is opened. Data is collected from the mass spectrometer and a portable computer provides contamination analysis. The CAU can be used to decontaminate and decommission hazardous and radioactive surfaces by measuring residual hazardous surface contamination, such as tritium and trace organics. It provides surface contamination data for research and development applications as well as real-time process control feedback for industrial cleaning operations and can be used to determine the readiness of a surface to accept bonding or coatings. 1 fig.

  18. NREL: Energy Analysis - Daniel Getman

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Daniel Getman Photo of Daniel Getman. Daniel Getman is a member of the Data Analysis and Visualization Group in the Strategic Energy Analysis Center. Geospatial Data Science Team...

  19. NREL: Energy Analysis - David Keyser

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of expertise Economic impact studies Time series analysis Analysis of labor and demographic data Primary research interests Static and dynamic economic impact models Labor...

  20. Germanium-76 Sample Analysis

    SciTech Connect (OSTI)

    Kouzes, Richard T.; Engelhard, Mark H.; Zhu, Zihua

    2011-04-01

    The MAJORANA DEMONSTRATOR is a large array of ultra-low background high-purity germanium detectors, enriched in 76Ge, designed to search for zero-neutrino double-beta decay (0???). The DEMONSTRATOR will utilize 76Ge from Russia, and the first one gram sample was received from the supplier for analysis on April 24, 2011. The Environmental Molecular Sciences facility, a DOE user facility at PNNL, was used to make the required isotopic and chemical purity measurements that are essential to the quality assurance for the MAJORANA DEMONSTRATOR. The results of this first analysis are reported here.

  1. Retrofit Financial Analysis Tool

    Office of Energy Efficiency and Renewable Energy (EERE)

    The Street and Parking Facility Lighting Retrofit Financial Analysis Tool was developed by a partnership of the DOE Municipal Solid-State Street Lighting Consortium, the Clinton Climate Initiative (CCI)/C40, and the Federal Energy Management Program (FEMP), for the financial analysis of retrofitting street and parking facility lighting with more efficient alternatives. Property owners, city and other government agencies, utilities, and energy efficiency organizations can use this tool to compute annualized energy and energy-cost savings, maintenance savings, greenhouse gas reductions, net present value, and simple payback associated with potential lighting upgrades.

  2. Radiative Flux Analysis

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Long, Chuck [NOAA

    2008-05-14

    The Radiative Flux Analysis is a technique for using surface broadband radiation measurements for detecting periods of clear (i.e. cloudless) skies, and using the detected clear-sky data to fit functions which are then used to produce continuous clear-sky estimates. The clear-sky estimates and measurements are then used in various ways to infer cloud macrophysical properties.

  3. Country Analysis Briefs

    Reports and Publications (EIA)

    2028-01-01

    An ongoing compilation of country energy profiles. The Energy Information Administration (EIA) maintains Country Analysis Briefs (CABs) for specific countries that are important to world energy markets, including members of the Organization of the Petroleum Exporting Countries (OPEC), major non-OPEC oil producers, major energy transit countries, major energy consumers, and other areas of current interest to energy analysts and policy makers.

  4. Electronic Mail Analysis Capability

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2001-01-08

    Establishes the pilot program to test the Department of Energy (DOE) Electronic Mail Analysis Capability (EMAC), which will be used to monitor and analyze outgoing and incoming electronic mail (e-mail) from the National Nuclear Security Administration (NNSA) and DOE laboratories that are engaged in nuclear weapons design or work involving special nuclear material. No cancellation.

  5. Shot loading trainer analysis

    SciTech Connect (OSTI)

    Peterson, T.K.

    1995-02-15

    This document presents the results from the analysis of the shot loading trainer (SLT). This device will be used to test the procedure for installing shot into the annulus of the Project W-320 shipping container. To ensure that the shot is installed uniformly around the container, vibrators will be used to settle the shot. The SLT was analyzed to ensure that it would not jeopardize worker safety during operation. The results from the static analysis of the SLT under deadweight and vibrator operating loads show that the stresses in the SLT are below code allowables. The results from the modal analysis show that the natural frequencies of the SLT are far below the operating frequencies of the vibrators, provided the SLT is mounted on pneumatic tires. The SLT was also analyzed for wind, seismic, deadweight, and moving/transporting loads. Analysis of the SLT is in accordance with SDC-4.1 for safety class 3 structures (DOE-RL 1993) and the American Institute of Steel Construction (AISC) Manual of Steel Construction (AISC 1989).

  6. Handsfree Surface Analysis

    Energy Science and Technology Software Center (OSTI)

    2006-11-01

    The HANDSFREE SURFACE ANALYSIS software code enables unattended analysis of surfaces by desorption electrospray (DESI) and liquid-junction surface sampling probe (SSP) mass spectrometry. The software allows automated lane scanning, imaging (e.g. lane rastering), spot and array sampling, and array scanning methods by controlling the movement of the sample attached to a computer-controlled stage. The software is able to collect, visualize and analyze mass spectrometry data real-time for surface analysis purposes by interacting with mass spectrometrymore » instrumentation software. The software also enables data post processing for imaging and other analytical purposes. The software also contains image analysis approaches to control the sampling capillary-to-surface distance when used with DESI, and for automated formation and real-time reoptimization of the sampling probe-to-surface liquid microjunction when used with SSP. Control of these distances is essential to automated, hands-free operation of a DESI or SSP mass spectrometry system.« less

  7. Regional Analysis Briefs

    Reports and Publications (EIA)

    2028-01-01

    Regional Analysis Briefs (RABs) provide an overview of specific regions that play an important role in world energy markets, either directly or indirectly. These briefs cover areas that are currently major producers (Caspian Sea), have geopolitical importance (South China Sea), or may have future potential as producers or transit areas (East Africa, Eastern Mediterranean).

  8. NID Copper Sample Analysis

    SciTech Connect (OSTI)

    Kouzes, Richard T.; Zhu, Zihua

    2011-09-12

    The current focal point of the nuclear physics program at PNNL is the MAJORANA DEMONSTRATOR, and the follow-on Tonne-Scale experiment, a large array of ultra-low background high-purity germanium detectors, enriched in 76Ge, designed to search for zero-neutrino double-beta decay (0???). This experiment requires the use of germanium isotopically enriched in 76Ge. The MAJORANA DEMONSTRATOR is a DOE and NSF funded project with a major science impact. The DEMONSTRATOR will utilize 76Ge from Russia, but for the Tonne-Scale experiment it is hoped that an alternate technology, possibly one under development at Nonlinear Ion Dynamics (NID), will be a viable, US-based, lower-cost source of separated material. Samples of separated material from NID require analysis to determine the isotopic distribution and impurities. DOE is funding NID through an SBIR grant for development of their separation technology for application to the Tonne-Scale experiment. The Environmental Molecular Sciences facility (EMSL), a DOE user facility at PNNL, has the required mass spectroscopy instruments for making isotopic measurements that are essential to the quality assurance for the MAJORANA DEMONSTRATOR and for the development of the future separation technology required for the Tonne-Scale experiment. A sample of isotopically separated copper was provided by NID to PNNL in January 2011 for isotopic analysis as a test of the NID technology. The results of that analysis are reported here. A second sample of isotopically separated copper was provided by NID to PNNL in August 2011 for isotopic analysis as a test of the NID technology. The results of that analysis are also reported here.

  9. STEP Utility Bill Analysis Report

    Broader source: Energy.gov [DOE]

    STEP Utility Bill Analysis Report, from the Tool Kit Framework: Small Town University Energy Program (STEP).

  10. REMOTE AREA RADIATION MONITORING (RARM) ALTERNATIVES ANALYSIS

    SciTech Connect (OSTI)

    NELSON RL

    2008-07-18

    The Remote Area Radiation Monitoring (RARM) system will be used to provide real-time radiation monitoring information to the operations personnel during tank retrieval and transfer operations. The primary focus of the system is to detect potential anomalous (waste leaks) or transient radiological conditions. This system will provide mobile, real-time radiological monitoring, data logging, and status at pre-selected strategic points along the waste transfer route during tank retrieval operations. The system will provide early detection and response capabilities for the Retrieval and Closure Operations organization and Radiological Control personnel.

  11. NREL: Energy Analysis - Jobs and Economic Competitiveness

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and Policy Impacts Analysis Workforce Development Competitive Advantage Competitve ... Energy Analysis Home Capabilities & Expertise Key Activities Analysis of Project Finance ...

  12. NREL: Energy Analysis - David Hurlbut

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Hurlbut Photo of David Hurlbut David Hurlbut is a member of the Market and Policy Impact Analysis Group in the Strategic Energy Analysis Center. Senior Analyst On staff since January 2007 Phone number: 303-384-7334 E-mail: david.hurlbut@nrel.gov Areas of expertise Policy and legislative analysis Statistical analysis and econometrics Optimization modeling Cost-benefit analysis Primary research interests Economic incentives and market behavior affecting energy efficiency and renewable energy

  13. Category:Core Analysis | Open Energy Information

    Open Energy Info (EERE)

    Analysis page? For detailed information on Core Analysis as exploration techniques, click here. Category:Core Analysis Add.png Add a new Core Analysis Technique Pages in...

  14. System Analysis Success Stories | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    System Analysis Success Stories System Analysis Success Stories Program Links System Analysis Projects System Analysis Success Stories Economic Impact Tools National Geothermal Data System (NGDS) Initiative

  15. NREL: Energy Analysis - News

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Bookmark and Share News The Decision Insight and Market Impacts newsletter highlights the lab's analysts and analysis activities in renewable energy and energy efficiency technologies are having an impact on U.S. energy goals. The newsletter features recent publications and websites, updates to our models and tools, and staff activities. You can subscribe to receive the newsletter monthly by email. March 2016 NREL is the nation's leader in clean energy technologies, practices, and strategies.

  16. NREL: Energy Analysis - Webmaster

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Webmaster Please enter your name and email address in the boxes provided, then type your message below. When you are finished, click "Send Message." NOTE: If you enter your e-mail address incorrectly, we will be unable to reply. Your name: Your email address: Your message: Send Message Printable Version Energy Analysis Home Capabilities & Expertise Key Activities Models & Tools Data & Resources Publications Partnerships Staff Working with Us Related Links News Did you find

  17. Transportation Energy Systems Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Systems Analysis - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Fuel Cycle Defense Waste Management Programs Advanced Nuclear

  18. Modeling & Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    nrt_blade_tip Permalink Gallery National Rotor Testbed aerodynamic design complete Modeling & Analysis, News, Renewable Energy, SWIFT, Wind Energy, Wind News National Rotor Testbed aerodynamic design complete The aerodynamic design of the National Rotor Testbed (NRT) blade has been completed (see example, above). The goal of the NRT rotor is to replicate the wake characteristics of a utility-scale rotor at the Scaled Wind Farm Technology (SWiFT) test site. This will allow researchers at

  19. Modeling & Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NearyFig1 Permalink Gallery University of Illinois uses Sandia Labs' reference hydrokinetic turbine to study potential bed erosion effects Energy, Modeling & Analysis, News, Partnership, Renewable Energy, Water Power University of Illinois uses Sandia Labs' reference hydrokinetic turbine to study potential bed erosion effects Sandia Labs Water Power Technologies Department promotes open-source marine hydrokinetic research by disseminating information on MHK technology designs initially

  20. Residual gas analysis device

    DOE Patents [OSTI]

    Thornberg, Steven M. (Peralta, NM)

    2012-07-31

    A system is provided for testing the hermeticity of a package, such as a microelectromechanical systems package containing a sealed gas volume, with a sampling device that has the capability to isolate the package and breach the gas seal connected to a pulse valve that can controllably transmit small volumes down to 2 nanoliters to a gas chamber for analysis using gas chromatography/mass spectroscopy diagnostics.

  1. safety analysis report

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    analysis report - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Fuel Cycle Defense Waste Management Programs Advanced Nuclear

  2. Independent Statistics & Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    April 2015 Independent Statistics & Analysis www.eia.gov U.S. Department of Energy Washington, DC 20585 Annual Coal Distribution Report 2013 This report was prepared by the U.S. Energy Information Administration (EIA), the statistical and analytical agency within the U.S. Department of Energy. By law, EIA's data, analyses, and forecasts are independent of approval by any other officer or employee of the United States Government. The views in this report therefore should not be construed as

  3. Independent Statistics & Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Independent Statistics & Analysis www.eia.gov U.S. Department of Energy Washington, DC 20585 Quarterly Coal Report (Abbreviated) July - September 2015 January 2016 This report was prepared by the U.S. Energy Information Administration (EIA), the statistical and analytical agency within the U.S. Department of Energy. By law, EIA's data, analyses, and forecasts are independent of approval by any other officer or employee of the United States Government. The views in this report therefore

  4. Mesh Morphing Pier Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Application of Mesh Morphing in STAR-CCM+ to Analysis of Scour at Cylindrical Piers Mesh morphing is a fluid structure interaction capability in STAR-CCM+ to move vertices in the computational mesh in a way that preserves mesh quality when a boundary moves. The equations being solved include terms that account for the motion of the mesh maintaining mass and property balances during the solution process. Initial work on leveraging the mesh morphing FSI capability for efficient application to

  5. Characterization and Failure Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and Failure Analysis - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Fuel Cycle Defense Waste Management Programs Advanced

  6. Independent Statistics & Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    March 2016 Independent Statistics & Analysis www.eia.gov U.S. Department of Energy Washington, DC 20585 Quarterly Coal Distribution Report October - December 2014 This report was prepared by the U.S. Energy Information Administration (EIA), the statistical and analytical agency within the U.S. Department of Energy. By law, EIA's data, analyses, and forecasts are independent of approval by any other officer or employee of the United States Government. The views in this report therefore should

  7. Automated Job Hazards Analysis

    Broader source: Energy.gov [DOE]

    AJHA Program - The Automated Job Hazard Analysis (AJHA) computer program is part of an enhanced work planning process employed at the Department of Energy's Hanford worksite. The AJHA system is routinely used to performed evaluations for medium and high risk work, and in the development of corrective maintenance work packages at the site. The tool is designed to ensure that workers are fully involved in identifying the hazards, requirements, and controls associated with tasks.

  8. SAMPLING AND ANALYSIS PROTOCOLS

    SciTech Connect (OSTI)

    Jannik, T; P Fledderman, P

    2007-02-09

    Radiological sampling and analyses are performed to collect data for a variety of specific reasons covering a wide range of projects. These activities include: Effluent monitoring; Environmental surveillance; Emergency response; Routine ambient monitoring; Background assessments; Nuclear license termination; Remediation; Deactivation and decommissioning (D&D); and Waste management. In this chapter, effluent monitoring and environmental surveillance programs at nuclear operating facilities and radiological sampling and analysis plans for remediation and D&D activities will be discussed.

  9. Statistical Analysis.indd

    Energy Savers [EERE]

    LM Stakeholder Interaction and External Communications June 2014 Page 1 OVERVIEW The U.S. Department of Energy (DOE) Offi ce of Legacy Management (LM) makes every effort to communicate with its stakeholders through public and small group meetings, conferences, briefi ngs, news releases, telephone, e-mail, informational materials, and through the LM website. To assess the effectiveness of LM's communication with stakeholders across the nation, an analysis of stakeholder interaction was performed.

  10. Association of residential dampness and mold with respiratory tract infections and bronchitis: a meta-analysis

    SciTech Connect (OSTI)

    Fisk, William J.; Eliseeva, Ekaterina A.; Mendell, Mark J.

    2010-11-15

    Dampness and mold have been shown in qualitative reviews to be associated with a variety of adverse respiratory health effects, including respiratory tract infections. Several published meta-analyses have provided quantitative summaries for some of these associations, but not for respiratory infections. Demonstrating a causal relationship between dampness-related agents, which are preventable exposures, and respiratory tract infections would suggest important new public health strategies. We report the results of quantitative meta-analyses of published studies that examined the association of dampness or mold in homes with respiratory infections and bronchitis. For primary studies meeting eligibility criteria, we transformed reported odds ratios (ORs) and confidence intervals (CIs) to the log scale. Both fixed and random effects models were applied to the log ORs and their variances. Most studies contained multiple estimated ORs. Models accounted for the correlation between multiple results within the studies analyzed. One set of analyses was performed with all eligible studies, and another set restricted to studies that controlled for age, gender, smoking, and socioeconomic status. Subgroups of studies were assessed to explore heterogeneity. Funnel plots were used to assess publication bias. The resulting summary estimates of ORs from random effects models based on all studies ranged from 1.38 to 1.50, with 95% CIs excluding the null in all cases. Use of different analysis models and restricting analyses based on control of multiple confounding variables changed findings only slightly. ORs (95% CIs) from random effects models using studies adjusting for major confounding variables were, for bronchitis, 1.45 (1.32-1.59); for respiratory infections, 1.44 (1.31-1.59); for respiratory infections excluding nonspecific upper respiratory infections, 1.50 (1.32-1.70), and for respiratory infections in children or infants, 1.48 (1.33-1.65). Little effect of publication bias was evident. Estimated attributable risk proportions ranged from 8% to 20%. Residential dampness and mold are associated with substantial and statistically significant increases in both respiratory infections and bronchitis. If these associations were confirmed as causal, effective control of dampness and mold in buildings would prevent a substantial proportion of respiratory infections.

  11. NID Copper Sample Analysis

    SciTech Connect (OSTI)

    Kouzes, Richard T.; Zhu, Zihua

    2011-02-01

    The current focal point of the nuclear physics program at PNNL is the MAJORANA DEMONSTRATOR, and the follow-on Tonne-Scale experiment, a large array of ultra-low background high-purity germanium detectors, enriched in 76Ge, designed to search for zero-neutrino double-beta decay (0???). This experiment requires the use of germanium isotopically enriched in 76Ge. The DEMONSTRATOR will utilize 76Ge from Russia, but for the Tonne-Scale experiment it is hoped that an alternate technology under development at Nonlinear Ion Dynamics (NID) will be a viable, US-based, lower-cost source of separated material. Samples of separated material from NID require analysis to determine the isotopic distribution and impurities. The MAJORANA DEMONSTRATOR is a DOE and NSF funded project with a major science impact. DOE is funding NID through an SBIR grant for development of their separation technology for application to the Tonne-Scale experiment. The Environmental Molecular Sciences facility (EMSL), a DOE user facility at PNNL, has the required mass spectroscopy instruments for making these isotopic measurements that are essential to the quality assurance for the MAJORANA DEMONSTRATOR and for the development of the future separation technology required for the Tonne-Scale experiment. A sample of isotopically separated copper was provided by NID to PNNL for isotopic analysis as a test of the NID technology. The results of that analysis are reported here.

  12. Text analysis methods, text analysis apparatuses, and articles of manufacture

    DOE Patents [OSTI]

    Whitney, Paul D; Willse, Alan R; Lopresti, Charles A; White, Amanda M

    2014-10-28

    Text analysis methods, text analysis apparatuses, and articles of manufacture are described according to some aspects. In one aspect, a text analysis method includes accessing information indicative of data content of a collection of text comprising a plurality of different topics, using a computing device, analyzing the information indicative of the data content, and using results of the analysis, identifying a presence of a new topic in the collection of text.

  13. Advanced Multivariate Analysis Tools Applied to Surface Analysis.

    Office of Scientific and Technical Information (OSTI)

    (Conference) | SciTech Connect Advanced Multivariate Analysis Tools Applied to Surface Analysis. Citation Details In-Document Search Title: Advanced Multivariate Analysis Tools Applied to Surface Analysis. No abstract prepared. Authors: Ohlhausen, James Anthony Publication Date: 2010-08-01 OSTI Identifier: 1022188 Report Number(s): SAND2010-5304C TRN: US201117%%662 DOE Contract Number: AC04-94AL85000 Resource Type: Conference Resource Relation: Conference: Proposed for presentation at the

  14. Clean Energy Policy Analysis: Impact Analysis of Potential Clean Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Policy Options for the Hawaii Clean Energy Initiative | Department of Energy Clean Energy Policy Analysis: Impact Analysis of Potential Clean Energy Policy Options for the Hawaii Clean Energy Initiative Clean Energy Policy Analysis: Impact Analysis of Potential Clean Energy Policy Options for the Hawaii Clean Energy Initiative This report provides detailed analyses of the following policies to determine the impact they may have on ratepayers, businesses, and the state in terms of energy

  15. Arundo Donax Analysis Report

    SciTech Connect (OSTI)

    Corrie I. Nichol, Ph.D.; Tyler L. Westover, Ph.D.

    2012-01-01

    This is a summary report of preliminary analysis conducted on Arundo Donax. Arundo Donax was received from Greenwood Resources via Portland General Electric. PGE plans to transition a coal-fired boiler to 100% biomass by 2020, and has partnered with EPRI and INL to conduct the necessary testing and development to understand what needs to take place to make this transition. Arundo Donax is a promising energy crop for biopower, and is as yet relatively untested and uncharacterized. The INL has begun initial characterization of this material, and this summary report presents the initial findings.

  16. Building Energy Consumption Analysis

    Energy Science and Technology Software Center (OSTI)

    2005-03-02

    DOE2.1E-121SUNOS is a set of modules for energy analysis in buildings. Modules are included to calculate the heating and cooling loads for each space in a building for each hour of a year (LOADS), to simulate the operation and response of the equipment and systems that control temperature and humidity and distribute heating, cooling and ventilation to the building (SYSTEMS), to model energy conversion equipment that uses fuel or electricity to provide the required heating,more » cooling and electricity (PLANT), and to compute the cost of energy and building operation based on utility rate schedule and economic parameters (ECONOMICS).« less

  17. PCard Data Analysis Tool

    Energy Science and Technology Software Center (OSTI)

    2005-04-01

    The Procurement Card data analysis and monitoring tool enables due-diligence review using predefined user-created queries and reports. The system tracks individual compliance emails. More specifically, the tool: - Helps identify exceptions or questionable and non-compliant purchases, - Creates audit random sample on request, - Allows users to create and run new or ad-hoc queries and reports, - Monitors disputed charges, - Creates predefined Emails to Cardholders requesting documentation and/or clarification, - Tracks audit status, notes,more » Email status (date sent, response), audit resolution.« less

  18. Dynamic cable analysis models

    SciTech Connect (OSTI)

    Palo, P.A.; Meggitt, D.J.; Nordell, W.J.

    1983-05-01

    This paper presents a summary of the development and validation of undersea cable dynamics computer models by the Naval Civil Engineering Laboratory (NCEL) under the sponsorship of the Naval Facilities Engineering Command. These models allow for the analysis of both small displacement (strumming) and large displacement (static and dynamic) deformations of arbitrarily configured cable structures. All of the large displacement models described in this paper are available to the public. This paper does not emphasize the theoretical development of the models (this information is available in other references) but emphasizes the various features of the models, the comparisons between model output and experimental data, and applications for which the models have been used.

  19. Drift Degradation Analysis

    SciTech Connect (OSTI)

    D. Kicker

    2004-09-16

    Degradation of underground openings as a function of time is a natural and expected occurrence for any subsurface excavation. Over time, changes occur to both the stress condition and the strength of the rock mass due to several interacting factors. Once the factors contributing to degradation are characterized, the effects of drift degradation can typically be mitigated through appropriate design and maintenance of the ground support system. However, for the emplacement drifts of the geologic repository at Yucca Mountain, it is necessary to characterize drift degradation over a 10,000-year period, which is well beyond the functional period of the ground support system. This document provides an analysis of the amount of drift degradation anticipated in repository emplacement drifts for discrete events and time increments extending throughout the 10,000-year regulatory period for postclosure performance. This revision of the drift degradation analysis was developed to support the license application and fulfill specific agreement items between the U.S. Nuclear Regulatory Commission (NRC) and the U.S. Department of Energy (DOE). The earlier versions of ''Drift Degradation Analysis'' (BSC 2001 [DIRS 156304]) relied primarily on the DRKBA numerical code, which provides for a probabilistic key-block assessment based on realistic fracture patterns determined from field mapping in the Exploratory Studies Facility (ESF) at Yucca Mountain. A key block is defined as a critical block in the surrounding rock mass of an excavation, which is removable and oriented in an unsafe manner such that it is likely to move into an opening unless support is provided. However, the use of the DRKBA code to determine potential rockfall data at the repository horizon during the postclosure period has several limitations: (1) The DRKBA code cannot explicitly apply dynamic loads due to seismic ground motion. (2) The DRKBA code cannot explicitly apply loads due to thermal stress. (3) The DRKBA code, which determines structurally controlled key-block failure, is not applicable for stress-controlled failure in the lithophysal units. To address these limitations, additional numerical codes have been included that can explicitly apply seismic and thermal loads, providing significant improvements to the analysis of drift degradation and extending the validity of drift degradation models.

  20. Tiling Microarray Analysis Tools

    SciTech Connect (OSTI)

    2005-05-04

    TiMAT is a package of 23 command line Java applications for use in the analysis of Affymetrix tiled genomic microarray data. TiMAT enables: 1) Rebuilding the genome annotation for entire tiled arrays (repeat filtering, chromosomal coordinate assignment). 2) Post processing of oligo intensity values (quantile normalization, median scaling, PMMM transformation), 3) Significance testing (Wilcoxon rank sum and signed rank tests, intensity difference and ratio tests) and Interval refinement (filtering based on multiple statistics, overlap comparisons), 4) Data visualization (detailed thumbnail/zoomed view with Interval Plots and data export to Affymetrix's Integrated Genome Browser) and Data reports (spreadsheet summaries and detailed profiles)

  1. Tiling Microarray Analysis Tools

    Energy Science and Technology Software Center (OSTI)

    2005-05-04

    TiMAT is a package of 23 command line Java applications for use in the analysis of Affymetrix tiled genomic microarray data. TiMAT enables: 1) Rebuilding the genome annotation for entire tiled arrays (repeat filtering, chromosomal coordinate assignment). 2) Post processing of oligo intensity values (quantile normalization, median scaling, PMMM transformation), 3) Significance testing (Wilcoxon rank sum and signed rank tests, intensity difference and ratio tests) and Interval refinement (filtering based on multiple statistics, overlap comparisons),more4) Data visualization (detailed thumbnail/zoomed view with Interval Plots and data export to Affymetrix's Integrated Genome Browser) and Data reports (spreadsheet summaries and detailed profiles)less

  2. Fast Analysis and Simulation Team | NISAC

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    SheetsFast Analysis and Simulation Team content top Fast Analysis and Simulation Team

  3. Systems Analysis Workshop Discussion Summary

    Broader source: Energy.gov [DOE]

    Discussion Summary from DOE Systems Analysis Workshop held in Washington, D.C. July 28-29, 2004 to discuss and define role of systems analysis in DOE Hydrogen Program.

  4. Systems Analysis Workshop Welcome & Introductions

    Broader source: Energy.gov [DOE]

    Welcome and introduction to the DOE Systems Analysis Workshop held in Washington, D.C. July 28-29, 2004 to discuss and define role of systems analysis in DOE Hydrogen Program.

  5. Crude Oil Analysis Database

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Shay, Johanna Y.

    The composition and physical properties of crude oil vary widely from one reservoir to another within an oil field, as well as from one field or region to another. Although all oils consist of hydrocarbons and their derivatives, the proportions of various types of compounds differ greatly. This makes some oils more suitable than others for specific refining processes and uses. To take advantage of this diversity, one needs access to information in a large database of crude oil analyses. The Crude Oil Analysis Database (COADB) currently satisfies this need by offering 9,056 crude oil analyses. Of these, 8,500 are United States domestic oils. The database contains results of analysis of the general properties and chemical composition, as well as the field, formation, and geographic location of the crude oil sample. [Taken from the Introduction to COAMDATA_DESC.pdf, part of the zipped software and database file at http://www.netl.doe.gov/technologies/oil-gas/Software/database.html] Save the zipped file to your PC. When opened, it will contain PDF documents and a large Excel spreadsheet. It will also contain the database in Microsoft Access 2002.

  6. Risk Analysis Virtual ENvironment

    Energy Science and Technology Software Center (OSTI)

    2014-02-10

    RAVEN has 3 major functionalities: 1. Provides a Graphical User Interface for the pre- and post-processing of the RELAP-7 input and output. 2. Provides the capability to model nuclear power plants control logic for the RELAP-7 code and dynamic control of the accident scenario evolution. This capability is based on a software structure that realizes a direct connection between the RELAP-7 solver engine (MOOSE) and a python environment where the variables describing the plant statusmore » are accessible in a scripting environment. RAVEN support the generation of the probabilistic scenario control by supplying a wide range of probability and cumulative distribution functions and their inverse functions. 3. Provides a general environment to perform probability risk analysis for RELAP-7, RELAP-5 and any generic MOOSE based applications. The probabilistic analysis is performed by sampling the input space of the coupled code parameters and it is enhanced by using modern artificial intelligence algorithms that accelerate the identification of the areas of major risk (in the input parameter space). This environment also provides a graphical visualization capability to analyze the outcomes. Among other approaches, the classical Monte Carlo and Latin Hypercube sampling algorithms are available. For the acceleration of the convergence of the sampling methodologies, Support Vector Machines, Bayesian regression, and collocation stochastic polynomials chaos are implemented. The same methodologies here described could be used to solve optimization and uncertainties propagation problems using the RAVEN framework.« less

  7. Sensitivity testing and analysis

    SciTech Connect (OSTI)

    Neyer, B.T.

    1991-01-01

    New methods of sensitivity testing and analysis are proposed. The new test method utilizes Maximum Likelihood Estimates to pick the next test level in order to maximize knowledge of both the mean, {mu}, and the standard deviation, {sigma} of the population. Simulation results demonstrate that this new test provides better estimators (less bias and smaller variance) of both {mu} and {sigma} than the other commonly used tests (Probit, Bruceton, Robbins-Monro, Langlie). A new method of analyzing sensitivity tests is also proposed. It uses the Likelihood Ratio Test to compute regions of arbitrary confidence. It can calculate confidence regions, for {mu}, {sigma}, and arbitrary percentiles. Unlike presently used methods, such as the program ASENT which is based on the Cramer-Rao theorem, it can analyze the results of all sensitivity tests, and it does not significantly underestimate the size of the confidence regions. The new test and analysis methods will be explained and compared to the presently used methods. 19 refs., 12 figs.

  8. analysis | OpenEI Community

    Open Energy Info (EERE)

    Alaska analysis appropriations Categorical Exclusions Coordinating Permit Office Cost Mechanisms Cost Recovery geothermal Hawaii NEPA permitting quarterly meeting White...

  9. NREL: Energy Analysis - Anelia Milbrandt

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Anelia Milbrandt Photo of Anelia Milbrandt. Anelia Milbrandt is a member of the Technology Systems and Sustainability Analysis Group in the Strategic Energy Analysis Center. She is also a member of the NREL International Studies Team. Senior Energy Resources Analyst On staff since 2003 Phone number: 303-275-4633 Email: anelia.milbrandt@nrel.gov Areas of expertise Biomass resource assessment Geospatial modeling and analysis Integrated resource, infrastructure, and market analysis Primary research

  10. NREL: Energy Analysis - Daniel Inman

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Inman Photo of Daniel Inman. Daniel Inman is a member of the Technology Systems and Sustainability Analysis Group in the Strategic Energy Analysis Center. Research Scientist On staff since February 2008 Phone number: 303-384-6845 E-mail: Daniel.Inman@nrel.gov Areas of expertise Life-cycle modeling of renewable fuels Feedstock production and handling Biofuel sustainability Statistical analysis of temporal and spatial datasets System dynamics Primary research interests Sustainability analysis

  11. NREL: Energy Analysis - Eric Lantz

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Eric Lantz Photo of Eric Lantz Eric Lantz is a member of the Market and Policy Impact Analysis Group in the Strategic Energy Analysis Center. Energy Analyst On staff since September 2008 Phone number: 303-384-7418 E-mail: eric.lantz@nrel.gov Areas of expertise Economic development impacts analysis State and federal policy analysis Primary research interests Policy applications for expanding renewable energy markets Evaluating economic and fiscal impacts of energy policy alternatives Social

  12. NREL: Energy Analysis - Ethan Warner

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Ethan Warner Photo of Ethan Warner Ethan Warner is a member of the Technology Systems and Sustainability Analysis Group in the Strategic Energy Analysis Center. Sustainability Analyst On staff since August 2009 Phone number: 303-384-7471 E-mail: ethan.warner@nrel.gov Areas of expertise Life cycle assessment System dynamics modeling Energy policy Policy analysis Risk analysis Primary research interests System dynamics modeling of renewable technologies and energy systems Technological, social,

  13. NREL: Energy Analysis - Lori Bird

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Lori Bird Photo of Lori Bird Lori Bird is a member of the Market and Policy Impact Analysis Group in the Strategic Energy Analysis Center. Principal Analyst On staff since early 1999 Phone number: 303-384-7412 E-mail: lori.bird@nrel.gov Areas of expertise Market analysis Policy analysis Primary research interests Renewable energy and carbon markets Renewable energy policy Interplay of emissions and renewables policies Education and background training M.E.S. in environmental management, 1997,

  14. NREL: Energy Analysis - Margaret Mann

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Margaret Mann Photo of Margaret Mann Margaret Mann is the group manager of the Technology Systems and Sustainability Analysis Group in the Strategic Energy Analysis Center. Group Manager On staff since 1993 Phone number: 303-275-2921 E-mail: margaret.mann@nrel.gov Areas of expertise Technical and economic feasibility analysis Environmental analysis Strategic planning for market development Primary research interests Life cycle assessment of renewable energy and conventional technologies

  15. NREL: Energy Analysis - Monisha Shah

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Monisha Shah Photo of Monisha Shah. Monisha Shah is a member of the Washington D.C. Office in the Strategic Energy Analysis Center. Senior Energy Analyst Phone number: 202-488-2229 Email: monisha.shah@nrel.gov Areas of expertise Energy, environmental, and economic modeling and analysis Benefits analysis (environmental, economic, health) Strategic analysis, program development and management, international capacity building Primary research interests International and domestic climate change

  16. NREL: Energy Analysis - Philipp Beiter

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Philipp Beiter Photo of Philipp Beiter Philipp Beiter is a member of the Market and Policy Impact Group in the Strategic Energy Analysis Center. Energy Markets and Policy Analyst On staff since October 2014 Phone number: 303-275-4383 E-mail: Philipp.Beiter@nrel.gov Areas of expertise Energy policy analysis Regulatory policy Data analysis and statistical modeling Primary research interests Electricity markets Utility business models for distributed generation Regulatory analysis Grid integration

  17. NREL: Energy Analysis - Scott Jenne

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Scott Jenne Photo of Scott Jenne Scott Jenne is a member of the Technology Systems and Sustainability Analysis Group in the Strategic Energy Analysis Center. Multidisciplinary Energy Engineer On staff since 2011 Phone number: 303-384-7248 E-mail: scott.jenne@nrel.gov Areas of expertise Techno-Economic Analysis Mechanical design 3D modeling and finite element analysis (FEA) Wave energy conversion Geothermal power cycles Primary research interests Cost reduction pathways of RE systems Integration

  18. NREL: Energy Analysis - Timothy Remo

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Timothy Remo Photo of Timothy Remo Timothy Remo is a member of the Technology Systems and Sustainability Analysis Group in the Strategic Energy Analysis Center. Solar PV Technologies Analyst and Engineer On staff since March 2015 Phone number: 303-275-3882 E-mail: Timothy.Remo@nrel.gov Areas of expertise Photovoltaic and Semiconductor Manufacturing Cost analysis Process development and process optimization Design of Experiments and data analysis Primary research interests PV growth as cost

  19. Geographically-Based Infrastructure Analysis

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Previous and Ongoing * HYDS ME - Evaluates best infrastructure options * Interstate Infrastructure Analysis - Minimal infrastructure to facilitate interstate travel during ...

  20. Financial Analysis | Department of Energy

    Energy Savers [EERE]

    Financial Analysis Financial Analysis The first step in financing a street lighting retrofit is a detailed financial analysis. Because street lighting systems are designed to last ten or twenty years, or even longer, all aspects of first costs, ongoing expenses, and long-term savings are important. While a preliminary or first-level analysis can be used to determine such things as simple payback, rate of return, and cost of light, the results may neglect a number of important economic

  1. Supply Forecast and Analysis (SFA)

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Matthew Langholtz Science Team Leader Oak Ridge National Laboratory DOE Bioenergy Technologies Office (BETO) 2015 Project Peer Review Supply Forecast and Analysis (SFA) 2 | Bioenergy Technologies Office Goal Statement * Provide timely and credible estimates of feedstock supplies and prices to support - the development of a bioeconomy; feedstock demand analysis of EISA, RFS2, and RPS mandates - the data and analysis of other projects in Analysis and Sustainability, Feedstock Supply and Logistics,

  2. Project Analysis Standard Operating Procedure

    Energy Savers [EERE]

    and Project Analysis Standard Operating Procedure (EPASOP) Issued by Office of Acquisition and Project Management MA-63 March 12, 2014 DEPARTMENT OF ENERGY Office of Acquisition and Project Management (OAPM) EVMS & PROJECT ANALYSIS SOP MARCH 2014 ii Earned Value Management System (EVMS) and Project Analysis Standard Operating Procedure (EPASOP) OPR: MA-63 March 2014 1. PURPOSE. This EVMS and Project Analysis Standard Operating Procedure (EPASOP) will serve as a primary reference for MA-631

  3. NREL: Energy Analysis - Key Activities

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Electric Sector Integration Energy-Water Nexus Life Cycle Assessment Harmonization Manufacturing Analysis Resource Assessment Models & Tools Data & Resources Publications...

  4. Systems Analysis | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Systems Analysis Systems Analysis Systems analysis provides direction, focus, and support for the development and introduction of hydrogen production, storage, and end-use technologies, and provides a basis for recommendations on a balanced portfolio of activities. All areas of the Fuel Cell Technologies Office-hydrogen production, delivery, storage, fuel cells, technology validation, and safety, codes and standards-rely on the conclusions and recommendations drawn from systems analysis results

  5. Renewable Fuels Legislation Impact Analysis

    Reports and Publications (EIA)

    2005-01-01

    An analysis based on an extension of the ethanol supply curve in our model to allow for enough ethanol production to meet the requirements of S. 650. This analysis provides an update of the May 23, 2005 analysis, with revised ethanol production and cost assumptions.

  6. Cross-impacts analysis development and energy policy analysis applications

    SciTech Connect (OSTI)

    Roop, J.M.; Scheer, R.M.; Stacey, G.S.

    1986-12-01

    Purpose of this report is to describe the cross-impact analysis process and microcomputer software developed for the Office of Policy, Planning, and Analysis (PPA) of DOE. First introduced in 1968, cross-impact analysis is a technique that produces scenarios of future conditions and possibilities. Cross-impact analysis has several unique attributes that make it a tool worth examining, especially in the current climate when the outlook for the economy and several of the key energy markets is uncertain. Cross-impact analysis complements the econometric, engineering, systems dynamics, or trend approaches already in use at DOE. Cross-impact analysis produces self-consistent scenarios in the broadest sense and can include interaction between the economy, technology, society and the environment. Energy policy analyses that couple broad scenarios of the future with detailed forecasting can produce more powerful results than scenario analysis or forecasts can produce alone.

  7. SDI CFD MODELING ANALYSIS

    SciTech Connect (OSTI)

    Lee, S.

    2011-05-05

    The Savannah River Remediation (SRR) Organization requested that Savannah River National Laboratory (SRNL) develop a Computational Fluid Dynamics (CFD) method to mix and blend the miscible contents of the blend tanks to ensure the contents are properly blended before they are transferred from the blend tank; such as, Tank 50H, to the Salt Waste Processing Facility (SWPF) feed tank. The work described here consists of two modeling areas. They are the mixing modeling analysis during miscible liquid blending operation, and the flow pattern analysis during transfer operation of the blended liquid. The transient CFD governing equations consisting of three momentum equations, one mass balance, two turbulence transport equations for kinetic energy and dissipation rate, and one species transport were solved by an iterative technique until the species concentrations of tank fluid were in equilibrium. The steady-state flow solutions for the entire tank fluid were used for flow pattern analysis, for velocity scaling analysis, and the initial conditions for transient blending calculations. A series of the modeling calculations were performed to estimate the blending times for various jet flow conditions, and to investigate the impact of the cooling coils on the blending time of the tank contents. The modeling results were benchmarked against the pilot scale test results. All of the flow and mixing models were performed with the nozzles installed at the mid-elevation, and parallel to the tank wall. From the CFD modeling calculations, the main results are summarized as follows: (1) The benchmark analyses for the CFD flow velocity and blending models demonstrate their consistency with Engineering Development Laboratory (EDL) and literature test results in terms of local velocity measurements and experimental observations. Thus, an application of the established criterion to SRS full scale tank will provide a better, physically-based estimate of the required mixing time, and elevation of transfer pump for minimum sludge disturbance. (2) An empirical equation for a tank with no cooling coils agrees reasonably with the current modeling results for the dual jet. (3) From the sensitivity study of the cooling coils, it was found that the tank mixing time for the coiled tank was about two times longer than that of the tank fluid with no coils under the 1/10th scale, while the coiled tank required only 50% longer than the one without coils under the full scale Tank 50H. In addition, the time difference is reduced when the pumping U{sub o}d{sub o} value is increased for a given tank. (4) The blending time for T-shape dual jet pump is about 20% longer than that of 15{sup o} upward V-shape pump under the 1/10th pilot-scale tank, while the time difference between the two pumps is about 12% for the full-scale Tank 50H. These results are consistent with the literature information. (5) A transfer pump with a solid-plate suction screen operating at 130 gpm can be located 9.5 inches above settled sludge for 2 in screen height in a 85 ft waste tank without disturbing any sludge. Detailed results are summarized in Table 13. Final pump performance calculations were made by using the established CW pump design, and operating conditions to satisfy the two requirements of minimum sludge disturbance, and adequate blending of tank contents. The final calculation results show that the blending times for the coiled and uncoiled tanks coupled with the CW pump design are 159 and 83 minutes, respectively. All the results are provided in Table 16.

  8. Malware detection and analysis

    DOE Patents [OSTI]

    Chiang, Ken; Lloyd, Levi; Crussell, Jonathan; Sanders, Benjamin; Erickson, Jeremy Lee; Fritz, David Jakob

    2016-03-22

    Embodiments of the invention describe systems and methods for malicious software detection and analysis. A binary executable comprising obfuscated malware on a host device may be received, and incident data indicating a time when the binary executable was received and identifying processes operating on the host device may be recorded. The binary executable is analyzed via a scalable plurality of execution environments, including one or more non-virtual execution environments and one or more virtual execution environments, to generate runtime data and deobfuscation data attributable to the binary executable. At least some of the runtime data and deobfuscation data attributable to the binary executable is stored in a shared database, while at least some of the incident data is stored in a private, non-shared database.

  9. Sensitivity Test Analysis

    Energy Science and Technology Software Center (OSTI)

    1992-02-20

    SENSIT,MUSIG,COMSEN is a set of three related programs for sensitivity test analysis. SENSIT conducts sensitivity tests. These tests are also known as threshold tests, LD50 tests, gap tests, drop weight tests, etc. SENSIT interactively instructs the experimenter on the proper level at which to stress the next specimen, based on the results of previous responses. MUSIG analyzes the results of a sensitivity test to determine the mean and standard deviation of the underlying population bymore » computing maximum likelihood estimates of these parameters. MUSIG also computes likelihood ratio joint confidence regions and individual confidence intervals. COMSEN compares the results of two sensitivity tests to see if the underlying populations are significantly different. COMSEN provides an unbiased method of distinguishing between statistical variation of the estimates of the parameters of the population and true population difference.« less

  10. Building Energy Consumption Analysis

    Energy Science and Technology Software Center (OSTI)

    2005-01-24

    DOE2.1E-121 is a set of modules for energy analysis in buildings. Modules are included to calculate the heating and cooling loads for each space in a building for each hour of a year (LOADS), to simulate the operation and response of the equipment and systems that control temperature and humidity and distribute heating, cooling and ventilation to the building (SYSTEMS), to model energy conversion equipment that uses fuel or electricity to provide the required heating,more » cooling and electricity (PLANT), and to compute the cost of energy and building operation based on utility rate schedule and economic parameters (ECONOMICS). DOE2.1E-121 contains modifications to DOE2.1E which allows 1000 zones to be modeled.« less

  11. Integrated fluorescence analysis system

    DOE Patents [OSTI]

    Buican, Tudor N. (Los Alamos, NM); Yoshida, Thomas M. (Los Alamos, NM)

    1992-01-01

    An integrated fluorescence analysis system enables a component part of a sample to be virtually sorted within a sample volume after a spectrum of the component part has been identified from a fluorescence spectrum of the entire sample in a flow cytometer. Birefringent optics enables the entire spectrum to be resolved into a set of numbers representing the intensity of spectral components of the spectrum. One or more spectral components are selected to program a scanning laser microscope, preferably a confocal microscope, whereby the spectrum from individual pixels or voxels in the sample can be compared. Individual pixels or voxels containing the selected spectral components are identified and an image may be formed to show the morphology of the sample with respect to only those components having the selected spectral components. There is no need for any physical sorting of the sample components to obtain the morphological information.

  12. Ultrasound Analysis of Slurries

    DOE Patents [OSTI]

    Soong, Yee and Blackwell, Arthur G.

    2005-11-01

    An autoclave reactor allows for the ultrasonic analysis of slurry concentration and particle size distribution at elevated temperatures and pressures while maintaining the temperature- and pressure-sensitive ultrasonic transducers under ambient conditions. The reactor vessel is a hollow stainless steel cylinder containing the slurry which includes a stirrer and a N, gas source for directing gas bubbles through the slurry. Input and output transducers are connected to opposed lateral portions of the hollow cylinder for respectively directing sound waves through the slurry and receiving these sound waves after transmission through the slurry, where changes in sound wave velocity and amplitude can be used to measure slurry parameters. Ultrasonic adapters connect the transducers to the reactor vessel in a sealed manner and isolate the transducers from the hostile conditions within the vessel without ultrasonic signal distortion or losses.

  13. Stack Trace Analysis Tool

    Energy Science and Technology Software Center (OSTI)

    2008-01-16

    STAT is a light weight debugging tool that gathers and merges stack traces from all of the processes in a parallel application. STAT uses the MRNet free based overlay network to broadcast commands from the tool front-end to the STAT daemons and for the front-end to gather the traces from the STAT daemons. As the traces propagate through the MRNet network tree, they are merged across all tasks to form a single call prefix tree.more » The call prefix tree can be examined to identify tasks with similar function call patterns and to delineate a small set of equivalence classes. A representative task from each of these classes can then be fed into a full feature debugger like TotalView for root cause analysis.« less

  14. Ultrasound Analysis Of Slurries

    DOE Patents [OSTI]

    Soong, Yee (Monroeville, PA); Blackwell, Arthur G. (Duquesne, PA)

    2005-11-01

    An autoclave reactor allows for the ultrasonic analysis of slurry concentration and particle size distribution at elevated temperatures and pressures while maintaining the temperature- and pressure-sensitive ultrasonic transducers under ambient conditions. The reactor vessel is a hollow stainless steel cylinder containing the slurry which includes a stirrer and a N.sub.2 gas source for directing gas bubbles through the slurry. Input and output transducers are connected to opposed lateral portions of the hollow cylinder for respectively directing sound waves through the slurry and receiving these sound waves after transmission through the slurry, where changes in sound wave velocity and amplitude can be used to measure slurry parameters. Ultrasonic adapters connect the transducers to the reactor vessel in a sealed manner and isolate the transducers from the hostile conditions within the vessel without ultrasonic signal distortion or losses.

  15. Sandia PUF Analysis Tool

    Energy Science and Technology Software Center (OSTI)

    2014-06-11

    This program is a graphical user interface for measuring and performing inter-active analysis of physical unclonable functions (PUFs). It is intended for demonstration and education purposes. See license.txt for license details. The program features a PUF visualization that demonstrates how signatures differ between PUFs and how they exhibit noise over repeated measurements. A similarity scoreboard shows the user how close the current measurement is to the closest chip signatures in the database. Other metrics suchmore » as average noise and inter-chip Hamming distances are presented to the user. Randomness tests published in NIST SP 800-22 can be computed and displayed. Noise and inter-chip histograms for the sample of PUFs and repeated PUF measurements can be drawn.« less

  16. Stack Trace Analysis Tool

    Energy Science and Technology Software Center (OSTI)

    2013-02-19

    STAT is a light weight debugging tool that gathers and merges stack traces from all of the processes in a parallell application. STAT uses the MRNet tree based overlay network to broadcast commands from the tool front-end to the STAT daemons and for the front-end to gather the traces from the STAT daemons. As the traces propagate through the MRNet network tree, they are merged across all tasks to from a single call prefix tree.more » The call prefix tree can be examined to identify tasks with similar function call patterns and to delineate a small set of equivalence slasses. A representative task from each of these classes can then be fed into a full feature debugger like TotalView for root cause analysis.« less

  17. Chemical process hazards analysis

    SciTech Connect (OSTI)

    1996-02-01

    The Office of Worker Health and Safety (EH-5) under the Assistant Secretary for the Environment, Safety and Health of the US Department (DOE) has published two handbooks for use by DOE contractors managing facilities and processes covered by the Occupational Safety and Health Administration (OSHA) Rule for Process Safety Management of Highly Hazardous Chemicals (29 CFR 1910.119), herein referred to as the PSM Rule. The PSM Rule contains an integrated set of chemical process safety management elements designed to prevent chemical releases that can lead to catastrophic fires, explosions, or toxic exposures. The purpose of the two handbooks, ``Process Safety Management for Highly Hazardous Chemicals`` and ``Chemical Process Hazards Analysis,`` is to facilitate implementation of the provisions of the PSM Rule within the DOE. The purpose of this handbook ``Chemical Process Hazards Analysis,`` is to facilitate, within the DOE, the performance of chemical process hazards analyses (PrHAs) as required under the PSM Rule. It provides basic information for the performance of PrHAs, and should not be considered a complete resource on PrHA methods. Likewise, to determine if a facility is covered by the PSM rule, the reader should refer to the handbook, ``Process Safety Management for Highly Hazardous Chemicals`` (DOE- HDBK-1101-96). Promulgation of the PSM Rule has heightened the awareness of chemical safety management issues within the DOE. This handbook is intended for use by DOE facilities and processes covered by the PSM rule to facilitate contractor implementation of the PrHA element of the PSM Rule. However, contractors whose facilities and processes not covered by the PSM Rule may also use this handbook as a basis for conducting process hazards analyses as part of their good management practices. This handbook explains the minimum requirements for PrHAs outlined in the PSM Rule. Nowhere have requirements been added beyond what is specifically required by the rule.

  18. Accident tolerant fuel analysis

    SciTech Connect (OSTI)

    Smith, Curtis; Chichester, Heather; Johns, Jesse; Teague, Melissa; Tonks, Michael Idaho National Laboratory; Youngblood, Robert

    2014-09-01

    Safety is central to the design, licensing, operation, and economics of Nuclear Power Plants (NPPs). Consequently, the ability to better characterize and quantify safety margin holds the key to improved decision making about light water reactor design, operation, and plant life extension. A systematic approach to characterization of safety margins and the subsequent margins management options represents a vital input to the licensee and regulatory analysis and decision making that will be involved. The purpose of the Risk Informed Safety Margin Characterization (RISMC) Pathway research and development (R&D) is to support plant decisions for risk-informed margins management by improving economics and reliability, and sustaining safety, of current NPPs. Goals of the RISMC Pathway are twofold: (1) Develop and demonstrate a risk-assessment method coupled to safety margin quantification that can be used by NPP decision makers as part of their margin recovery strategies. (2) Create an advanced ''RISMC toolkit'' that enables more accurate representation of NPP safety margin. In order to carry out the R&D needed for the Pathway, the Idaho National Laboratory is performing a series of case studies that will explore methods- and tools-development issues, in addition to being of current interest in their own right. One such study is a comparative analysis of safety margins of plants using different fuel cladding types: specifically, a comparison between current-technology Zircaloy cladding and a notional ''accident-tolerant'' (e.g., SiC-based) cladding. The present report begins the process of applying capabilities that are still under development to the problem of assessing new fuel designs. The approach and lessons learned from this case study will be included in future Technical Basis Guides produced by the RISMC Pathway. These guides will be the mechanism for developing the specifications for RISMC tools and for defining how plant decision makers should propose and evaluate margin recovery strategies.

  19. Accident Tolerant Fuel Analysis

    SciTech Connect (OSTI)

    Curtis Smith; Heather Chichester; Jesse Johns; Melissa Teague; Michael Tonks; Robert Youngblood

    2014-09-01

    Safety is central to the design, licensing, operation, and economics of Nuclear Power Plants (NPPs). Consequently, the ability to better characterize and quantify safety margin holds the key to improved decision making about light water reactor design, operation, and plant life extension. A systematic approach to characterization of safety margins and the subsequent margins management options represents a vital input to the licensee and regulatory analysis and decision making that will be involved. The purpose of the Risk Informed Safety Margin Characterization (RISMC) Pathway research and development (R&D) is to support plant decisions for risk-informed margins management by improving economics and reliability, and sustaining safety, of current NPPs. Goals of the RISMC Pathway are twofold: (1) Develop and demonstrate a risk-assessment method coupled to safety margin quantification that can be used by NPP decision makers as part of their margin recovery strategies. (2) Create an advanced RISMC toolkit that enables more accurate representation of NPP safety margin. In order to carry out the R&D needed for the Pathway, the Idaho National Laboratory is performing a series of case studies that will explore methods- and tools-development issues, in addition to being of current interest in their own right. One such study is a comparative analysis of safety margins of plants using different fuel cladding types: specifically, a comparison between current-technology Zircaloy cladding and a notional accident-tolerant (e.g., SiC-based) cladding. The present report begins the process of applying capabilities that are still under development to the problem of assessing new fuel designs. The approach and lessons learned from this case study will be included in future Technical Basis Guides produced by the RISMC Pathway. These guides will be the mechanism for developing the specifications for RISMC tools and for defining how plant decision makers should propose and evaluate margin recovery strategies.

  20. Hypothesis analysis methods, hypothesis analysis devices, and articles of manufacture

    DOE Patents [OSTI]

    Sanfilippo, Antonio P. (Richland, WA); Cowell, Andrew J. (Kennewick, WA); Gregory, Michelle L. (Richland, WA); Baddeley, Robert L. (Richland, WA); Paulson, Patrick R. (Pasco, WA); Tratz, Stephen C. (Richland, WA); Hohimer, Ryan E. (West Richland, WA)

    2012-03-20

    Hypothesis analysis methods, hypothesis analysis devices, and articles of manufacture are described according to some aspects. In one aspect, a hypothesis analysis method includes providing a hypothesis, providing an indicator which at least one of supports and refutes the hypothesis, using the indicator, associating evidence with the hypothesis, weighting the association of the evidence with the hypothesis, and using the weighting, providing information regarding the accuracy of the hypothesis.

  1. NREL: Energy Analysis - Hydrogen and Fuel Cells Technology Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Hydrogen and Fuel Cells Technology Analysis NREL's hydrogen systems analysis activities provide direction, insight, and support for the development, demonstration, and deployment of a broad range of hydrogen technologies. Analysis focuses on hydrogen production, storage, and delivery systems for fuel cell electric vehicles (FCEVs) as well as stationary fuel cells and emerging-market applications such as material handling and backup power. NREL's hydrogen systems analysts evaluate R&D goals

  2. Real time analysis under EDS

    SciTech Connect (OSTI)

    Schneberk, D.

    1985-07-01

    This paper describes the analysis component of the Enrichment Diagnostic System (EDS) developed for the Atomic Vapor Laser Isotope Separation Program (AVLIS) at Lawrence Livermore National Laboratory (LLNL). Four different types of analysis are performed on data acquired through EDS: (1) absorption spectroscopy on laser-generated spectral lines, (2) mass spectrometer analysis, (3) general purpose waveform analysis, and (4) separation performance calculations. The information produced from this data includes: measures of particle density and velocity, partial pressures of residual gases, and overall measures of isotope enrichment. The analysis component supports a variety of real-time modeling tasks, a means for broadcasting data to other nodes, and a great degree of flexibility for tailoring computations to the exact needs of the process. A particular data base structure and program flow is common to all types of analysis. Key elements of the analysis component are: (1) a fast access data base which can configure all types of analysis, (2) a selected set of analysis routines, (3) a general purpose data manipulation and graphics package for the results of real time analysis. Each of these components are described with an emphasis upon how each contributes to overall system capability. 3 figs.

  3. Analysis Models and Tools: Systems Analysis of Hydrogen and Fuel...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Power (FCPower) Model PDF icon Global Pathways Analysis Tool (GPAT) PDF icon Greenhouse Gases, Regulated Emissions, and Energy use in Transportation (GREET) Model PDF icon ...

  4. NREL: Energy Analysis - About the Strategic Energy Analysis Center

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Resource Assessment Electric Sector Integration Jobs and Economic Competitiveness Life Cycle Assessment Harmonization Analysis of Project Finance What is the SEAC? NREL and the...

  5. NREL: Energy Analysis - Vehicles and Fuels Research Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Analysis and Integration Evaluates advanced vehicle technologies to determine their impact on fuel economy, vehicle performance, exhaust emissions, and more. Transportation...

  6. Pulse Analysis Spectroradiometer System (PASS) Software - Energy...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Energy Analysis Energy Analysis Find More Like This Return to Search Pulse Analysis ... SummaryFlashing artificial light sources are used extensively in photovoltaic ...

  7. Analysis of Geothermal Reservoir Stimulation using Geomechanics...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Stochastic Analysis of Injection-Induced Seismicity Analysis of Geothermal Reservoir Stimulation using Geomechanics-Based Stochastic Analysis of Injection-Induced Seismicity ...

  8. Threat Analysis Framework | Department of Energy

    Office of Environmental Management (EM)

    Threat Analysis Framework Threat Analysis Framework The need to protect national critical infrastructure has led to the development of a threat analysis framework. The threat ...

  9. EA-1975: Supplement Analysis | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    5: Supplement Analysis EA-1975: Supplement Analysis LINAC Coherent Light Source-Il, SLAC National Accelerator Laboratory, Menlo Park, California This document provides an analysis...

  10. Frequency Response Analysis Tool

    SciTech Connect (OSTI)

    Etingov, Pavel V.; Kosterev, Dmitry; Dai, T.

    2014-12-31

    Frequency response has received a lot of attention in recent years at the national level, which culminated in the development and approval of North American Electricity Reliability Corporation (NERC) BAL-003-1 Frequency Response and Frequency Bias Setting Reliability Standard. This report is prepared to describe the details of the work conducted by Pacific Northwest National Laboratory (PNNL) in collaboration with the Bonneville Power Administration and Western Electricity Coordinating Council (WECC) Joint Synchronized Information Subcommittee (JSIS) to develop a frequency response analysis tool (FRAT). The document provides the details on the methodology and main features of the FRAT. The tool manages the database of under-frequency events and calculates the frequency response baseline. Frequency response calculations are consistent with frequency response measure (FRM) in NERC BAL-003-1 for an interconnection and balancing authority. The FRAT can use both phasor measurement unit (PMU) data, where available, and supervisory control and data acquisition (SCADA) data. The tool is also capable of automatically generating NERC Frequency Response Survey (FRS) forms required by BAL-003-1 Standard.

  11. Residential Building Energy Analysis

    Energy Science and Technology Software Center (OSTI)

    1990-09-01

    PEAR (Program for Energy Analysis of Residences) provides an easy-to-use and accurate method of estimating the energy and cost savings associated with various energy conservation measures in site-built single-family homes. Measures such as ceiling, wall, and floor insulation; different window type and glazing layers; infiltration levels; and equipment efficiency can be considered. PEAR also allows the user to consider the effects of roof and wall color, movable night insulation on the windows, reflective and heatmore » absorbing glass, an attached sunspace, and use of a night temperature setback. Regression techniques permit adjustments for different building geometries, window areas and orientations, wall construction, and extension of the data to 880 U.S. locations determined by climate parameters. Based on annual energy savings, user-specified costs of conservation measures, fuel, lifetime of measure, loan period, and fuel escalation and interest rates, PEAR calculates two economic indicators; the Simple Payback Period (SPP) and the Savings-to-Investment Ratio (SIR). Energy and cost savings of different sets of conservation measures can be compared in a single run. The program can be used both as a research tool by energy policy analysts and as a method for nontechnical energy calculation by architects, home builders, home owners, and others in the building industry.« less

  12. Community Energy Consumption Analysis

    Energy Science and Technology Software Center (OSTI)

    1992-02-21

    The TDIST3 program performs an analysis of large integrated community total energy systems (TES) supplying thermal and electrical energy from one or more power stations. The program models the time-dependent energy demands of a group of representative building types, distributes the thermal demands within a thermal utility system (TUS), simulates the dynamic response of a group of power stations in meeting the TUS demands, and designs an optimal base-loaded (electrically) power plant and thermal energymore » storage reservoir combination. The capital cost of the TES is evaluated. The program was developed primarily to analyze thermal utility systems supplied with high temperature water (HTW) from more than one power plant. The TUS consists of a transmission loop and secondary loops with a heat exchanger linking each secondary loop to the transmission loop. The power stations electrical output supplies all community buildings and the HTW supplies the thermal demand of the buildings connected through the TUS, a piping network. Basic components of the TES model are one or more power stations connected to the transmission loop. These may be dual-purpose, producing electricity and HTW, or just heating plants producing HTW. A thermal storage reservoir is located at one power station. The secondary loops may have heating plants connected to them. The transmission loop delivers HTW to local districts; the secondary loops deliver the energy to the individual buildings in a district.« less

  13. Signal Processing, Analysis, & Display

    Energy Science and Technology Software Center (OSTI)

    1986-06-01

    SIG is a general-purpose signal processing, analysis, and display program. Its main purpose is to perform manipulations on time- and frequency-domain signals. However, it has been designed to ultimately accommodate other representations for data such as multiplexed signals and complex matrices. Two user interfaces are provided in SIG - a menu mode for the unfamiliar user and a command mode for more experienced users. In both modes errors are detected as early as possible andmoreare indicated by friendly, meaningful messages. An on-line HELP package is also included. A variety of operations can be performed on time- and frequency-domain signals including operations on the samples of a signal, operations on the entire signal, and operations on two or more signals. Signal processing operations that can be performed are digital filtering (median, Bessel, Butterworth, and Chebychev), ensemble average, resample, auto and cross spectral density, transfer function and impulse response, trend removal, convolution, Fourier transform and inverse window functions (Hamming, Kaiser-Bessel), simulation (ramp, sine, pulsetrain, random), and read/write signals. User definable signal processing algorithms are also featured. SIG has many options including multiple commands per line, command files with arguments,commenting lines, defining commands, and automatic execution for each item in a repeat sequence. Graphical operations on signals and spectra include: x-y plots of time signals; real, imaginary, magnitude, and phase plots of spectra; scaling of spectra for continuous or discrete domain; cursor zoom; families of curves; and multiple viewports.less

  14. Quantum Graph Analysis

    SciTech Connect (OSTI)

    Maunz, Peter Lukas Wilhelm; Sterk, Jonathan David; Lobser, Daniel; Parekh, Ojas D.; Ryan-Anderson, Ciaran

    2016-01-01

    In recent years, advanced network analytics have become increasingly important to na- tional security with applications ranging from cyber security to detection and disruption of ter- rorist networks. While classical computing solutions have received considerable investment, the development of quantum algorithms to address problems, such as data mining of attributed relational graphs, is a largely unexplored space. Recent theoretical work has shown that quan- tum algorithms for graph analysis can be more efficient than their classical counterparts. Here, we have implemented a trapped-ion-based two-qubit quantum information proces- sor to address these goals. Building on Sandia's microfabricated silicon surface ion traps, we have designed, realized and characterized a quantum information processor using the hyperfine qubits encoded in two 171 Yb + ions. We have implemented single qubit gates using resonant microwave radiation and have employed Gate set tomography (GST) to characterize the quan- tum process. For the first time, we were able to prove that the quantum process surpasses the fault tolerance thresholds of some quantum codes by demonstrating a diamond norm distance of less than 1 . 9 x 10 [?] 4 . We used Raman transitions in order to manipulate the trapped ions' motion and realize two-qubit gates. We characterized the implemented motion sensitive and insensitive single qubit processes and achieved a maximal process infidelity of 6 . 5 x 10 [?] 5 . We implemented the two-qubit gate proposed by Molmer and Sorensen and achieved a fidelity of more than 97 . 7%.

  15. MGR External Events Hazards Analysis

    SciTech Connect (OSTI)

    L. Booth

    1999-11-06

    The purpose and objective of this analysis is to apply an external events Hazards Analysis (HA) to the License Application Design Selection Enhanced Design Alternative 11 [(LADS EDA II design (Reference 8.32))]. The output of the HA is called a Hazards List (HL). This analysis supersedes the external hazards portion of Rev. 00 of the PHA (Reference 8.1). The PHA for internal events will also be updated to the LADS EDA II design but under a separate analysis. Like the PHA methodology, the HA methodology provides a systematic method to identify potential hazards during the 100-year Monitored Geologic Repository (MGR) operating period updated to reflect the EDA II design. The resulting events on the HL are candidates that may have potential radiological consequences as determined during Design Basis Events (DBEs) analyses. Therefore, the HL that results from this analysis will undergo further screening and analysis based on the criteria that apply during the performance of DBE analyses.

  16. Environmental Analysis | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Environmental Analysis Environmental Analysis Environmental Analysis is used by the Program to quantify the environmental impacts of hydrogen technologies. Specifically, life cycle assessment is used to identify and evaluate the emissions, resource consumption, and energy use of all processes required to make the process of interest operate, including raw material extraction, transportation, processing, and final disposal of all products and by-products. Also known as cradle-to-grave or

  17. ORISE: Data Collection and Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Data Collection and Analysis The Oak Ridge Institute for Science and Education (ORISE) assists government agencies and organizations in acquiring evidence from systematic data collection procedures and analyzing data before, during and after program implementation. ORISE performs data analysis and collection using one or more of the following tactics: Primary and secondary literature reviews Environmental scans Focus groups Key informant interview Surveys and questionnaires Media analysis and

  18. ORISE: Media Analysis and Monitoring

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Media Analysis and Monitoring The Oak Ridge Institute for Science and Education (ORISE) uses comprehensive media analysis and monitoring tools to define media interest and the public's perceptions of a particular issue. ORISE's media analysis process includes analyzing news reports combined with media outlet data, such as circulation, readership, number of viewers and listeners; recording frequency of publication and collecting quotes from subject matter experts. To improve the overall

  19. NREL: Energy Analysis - Ahmad Mayyas

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Ahmad Mayyas Photo of Ahmad Mayyas Ahmad Mayyas is a member of the Technology Systems and Sustainability Analysis Group in the Strategic Energy Analysis Center. Clean Energy Manufacturing and Cost Analyst On staff since April, 2015 Phone number: 303-384-7446 E-mail: Ahmad.Mayyas@nrel.gov Areas of expertise Life cycle assessment of renewable and sustainable energy systems Design for sustainability/environment for automobiles Sustainable manufacturing and energy analysis Advanced engineering

  20. NREL: Energy Analysis - Anthony Lopez

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Anthony Lopez Photo of Anthony Lopez Anthony Lopez is the section supervisor of the Data Analysis and Visualization Group in the Strategic Energy Analysis Center. GIS Scientist IV - Section Supervisor On staff since April 2009 Phone number: 303-275-3654 E-mail: anthony.lopez@nrel.gov Areas of expertise Spatial Database Design and Utilization High Performance Computing Parallel Processing and Analysis of Large Geospatial Datasets Visualization of Complex Spatial-Temporal Datasets Renewable

  1. NREL: Energy Analysis - Cara Marcy

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Cara Marcy Photo of Cara Marcy Cara Marcy is a member of the Market and Policy Impact Group in the Strategic Energy Analysis Center. Renewable Electricity Analyst On staff since September 2015 Phone number: 303-275-3740 E-mail: Cara.Marcy@nrel.gov Areas of expertise Energy policy analysis Data analysis and modeling Utility-scale wind, solar, and energy storage Primary research interests Renewable electricity policy and market modelling Renewable generation and energy storage integration Regional

  2. NREL: Energy Analysis - Daniel Steinberg

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Steinberg Photo of Daniel Steinberg Daniel Steinberg is a section supervisor of the Energy Forecasting and Modeling Group in the Strategic Energy Analysis Center. Senior Policy and Economic Analyst - Electricity Planning Section Supervisor On staff since September 2009 Phone number: 303-275-4287 E-mail: daniel.steinberg@nrel.gov Areas of expertise Energy policy and regulatory analysis Econometric analysis Modeling of interactions between climate change and the energy sector Primary research

  3. NREL: Energy Analysis - Dave Bielen

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Dave Bielen Photo of Dave Bielen Dave Bielen is a member of the Energy Forecasting and Modeling Group in the Strategic Energy Analysis Center. Energy and Environmental Policy Analyst On staff since June 2015 Phone number: 303-275-4921 E-mail: david.bielen@nrel.gov Areas of expertise Environmental policy design Dynamic programming Time series and microeconometric analysis Primary research interests Distributional impact analysis of environmental and energy policy GHG emissions mitigation in the

  4. NREL: Energy Analysis - David Harrison

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Harrison David Harrison is a member of the Data Analysis and Visualization Group in the Strategic Energy Analysis Center. Software Engineer On staff since 2009 Phone number: 303-275-4411 E-mail: david.harrison@nrel.gov Areas of expertise Data design and database administration Custom software solutions Full systems development life cycle Primary research interests Oracle and PostgreSQL database management Open source NoSQL implementations Geographic data design, maintenance, and analysis

  5. NREL: Energy Analysis - David Mooney

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Mooney Photo of David Mooney David Mooney is the center director of the Strategic Energy Analysis Center. Center Director On staff since August 2002 Phone number: 303-384-6782 E-mail: David.Mooney@nrel.gov Analysis expertise Strategic planning Broad knowledge base in technologies and markets for energy technologies and their integration into the current energy infrastructure. Technical and operational knowledge of the photovoltaics technologies and industry Design and cost analysis of

  6. NREL: Energy Analysis - Dylan Hettinger

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Dylan Hettinger Photo of Dylan Hettinger. Dylan Hettinger is a member of the Data Analysis and Visualization Group in the Strategic Energy Analysis Center. GIS Programmer Analyst On staff since 2010 Phone number: 303-275-3750 E-mail: dylan.hettinger@nrel.gov Areas of expertise Information design Spatial analysis and cartography Prior work experience AMEC Earth & Environmental, Denver, CO Greenhorne & O'Mara, Raleigh, NC Personal interests/hobbies All kinds of climbing and cycling

  7. NREL: Energy Analysis - Garvin Heath

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Garvin Heath Photo of Garvin Heath Garvin Heath is a member of the Technology Systems and Sustainability Analysis Group in the Strategic Energy Analysis Center. Senior Scientist On staff since January 2008 Phone number: 303-384-7460 E-mail: garvin.heath@nrel.gov Areas of expertise Life cycle assessment Sustainability analysis Air quality modeling Exposure assessment Primary research interests Health and environmental impacts of energy technologies, including externalities Life cycle assessment

  8. NREL: Energy Analysis - Katherine Young

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Katherine Young, P.E. Photo of Katherine Young Katherine Young is a member of the Technology Systems and Sustainability Analysis Group in the Strategic Energy Analysis Center. Geothermal Energy Engineer On staff since June 2008 Phone number: 303-384-7402 E-mail: katherine.young@nrel.gov Areas of expertise Geothermal exploration analysis Regulatory and permitting Resource reporting Geothermal direct use (thermal applications) Water rights and resources engineering Database planning and

  9. NREL: Energy Analysis - Kathleen Nawaz

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Kathleen Nawaz Photo of Kathleen Nawaz Kathleen Nawaz is a Senior Advisor for the Strategic Energy Analysis Center at the Washington D.C. Office. Senior Advisor On staff since 2001 Phone number: 202-488-2218 E-mail: kathleen.nawaz@nrel.gov Areas of expertise Global climate change and renewable energy Co-benefits/development impact analysis Low carbon transportation Primary research interests Low emissions development planning and analysis Energy and international development Education and

  10. NREL: Energy Analysis - Meghan Mooney

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Meghan Mooney Photo of Meghan Mooney Meghan Mooney is a member of the Data Analysis and Visualization Group in the Strategic Energy Analysis Center. GIS Scientist II On staff since June 2015 Phone number: 303-384-7315 E-mail: meghan.mooney@nrel.gov Areas of expertise Spatial Analysis Statistics Cartography Transportation/mobility Primary research interests Transportation and alternative fuels Mobility and behavioral dimensions of climate change VGI and mixed methods GIS Education and background

  11. NREL: Energy Analysis - Michael Bahl

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Bahl Photo of Michael Bahl Michael Bahl is a member of the Data Analysis and Visualization Group in the Strategic Energy Analysis Center. Senior Research Engineer On staff since December 2010 Phone number: 303-275-4464 E-mail: michael.bahl@nrel.gov Areas of expertise Software development and architecture of enterprise solutions Process improvement and guidance Scrum Master Primary research interests Analysis and management of large data sets Education and background training M.S. in computer

  12. NREL: Energy Analysis - Michael Gleason

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Gleason Michael Gleason is a member of the Data Analysis and Visualization Group in the Strategic Energy Analysis Center. Scientist III - GIS On staff since April 2014 Phone number: 303-275-4109 E-mail: Michael.Gleason@nrel.gov Areas of expertise Geospatial analysis and modeling Scientific programming Multivariate data visualization Technical writing and editing Primary research interests Modeling technical resource potential for renewable technologies Modeling market diffusion of distributed

  13. NREL: Energy Analysis - Nick Langle

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Langle Photo of Nick Langle. Nick Langle is a member of the Data Analysis and Visualization Group in the Strategic Energy Analysis Center. Front End Web Engineer On staff since July 2010 Phone number: 303-275-3775 E-mail: nicholas.langle@nrel.gov Areas of expertise HTML / CSS / Javascript / jQuery UI / UX Responsive Web Design Semantic MediaWiki SEO Primary research interests Web Design & Usability Data Visualization & Analytics Geospatial Analysis Transportation & Alternative Fuels

  14. NREL: Energy Analysis - Paul Schwabe

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Schwabe Photo of Paul Schwabe Paul Schwabe is a member of the Market and Policy Impact Analysis Group in the Strategic Energy Analysis Center. Energy and Financial Analyst On staff since August 2008 Phone number: 303-384-7468 E-mail: paul.schwabe@nrel.gov Areas of expertise Electricity market financial analysis Natural gas volume and revenue forecasting Energy efficiency and conservation, including electric and natural gas rate decoupling Primary research interests Market penetration and

  15. NREL: Energy Analysis - Rebecca Hanes

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Rebecca Hanes Photo of Rebecca Hanes Rebecca Hanes is a member of the Technology Systems and Sustainability Analysis Group in the Strategic Energy Analysis Center. Chemical Engineering Analyst for Renewable Energy Technologies On staff since July 2015 Phone number: 303-275-4397 E-mail: rebecca.hanes@nrel.gov Areas of expertise Mathematical and theoretical aspects of life cycle inventories Economic and environmentally extended input-output analysis Sustainable design and optimization of

  16. NREL: Energy Analysis - Stuart Cohen

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Stuart Cohen Photo of Stuart Cohen Stuart Cohen is a member of the Energy Forecasting and Modeling Group in the Strategic Energy Analysis Center. Electric System Modeler On staff since September 2012 Phone number: 303-275-4369 E-mail: stuart.cohen@nrel.gov Areas of expertise Electricity system analysis Optimization and data analysis in GAMS and MATLAB Carbon capture and sequestration Primary research interests Multi-scale electricity systems modeling and optimization (e.g. ReEDS) Optimizing

  17. NREL: Energy Analysis - Tyler Stehly

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Tyler Stehly Photo of Tyler Stehly. Tyler Stehly is a member of the Technology Systems and Sustainability Analysis Group in the Strategic Energy Analysis Center. Engineering Wind Technology Analyst On staff since 2012 Phone number: 303-384-7190 E-mail: Tyler.Stehly@nrel.gov Areas of expertise Energy economic models Wind energy systems Cost of energy analysis Project cost estimation Technical report writing Primary research interests Wind technologies Renewable energy systems Mechanisms and

  18. NREL: Energy Analysis - Yimin Zhang

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Yimin Zhang Photo of Yimin Zhang Yimin Zhang is a member of the Technology Systems and Sustainability Analysis Group in the Strategic Energy Analysis Center. Research Analyst On staff since April 2010 Phone number: 303-275-3258 E-mail: yimin.zhang@nrel.gov Areas of expertise Life cycle assessment Cost-effectiveness analysis of greenhouse gas emissions reduction Primary research interests Life cycle assessment for biofuels Sustainability Competing uses of biomass resources Education and

  19. Articles about Wind Program Analysis

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    6301 Articles about Wind Program Analysis en New Report Shows Domestic Offshore Wind Industry Potential, 21 Projects Planned in U.S. Waters http:energy.goveerearticles...

  20. FP-33 Final Analysis Report

    SciTech Connect (OSTI)

    Williams, R. W.

    2015-10-02

    This report describes an analysis of 244Pu from VNIIEF (FP-33) sent to the Lawrence Livermore National Laboratory as test samples.

  1. Cuttings Analysis | Open Energy Information

    Open Energy Info (EERE)

    And Deep Electrical Sounding Cuttings Analysis At Long Valley Caldera Geothermal Area (Smith & Suemnicht, 1991) Long Valley Caldera Geothermal Area 1985 1988 Oxygen Isotope...

  2. NREL: Energy Analysis - Carolyn Davidson

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Carolyn Davidson Photo of Carolyn Davidson Carolyn Davidson is a member of the Energy Forecasting and Modeling Group in the Strategic Energy Analysis Center. Economic Analyst On...

  3. Global Pathways Analysis Tool (GPAT)

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Pathways Analysis Tool (GPAT) (Sandia National Laboratories) Objectives Calculate least-cost pathways for hydrogen supply for eight participating countries: France, Germany, ...

  4. NREL: Energy Analysis - Related Links

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    analysis capabilities, energy-modeling, and technology expertise related to renewable energy. International Applications NREL's International Program in its effort to promote the...

  5. Biomass Rapid Analysis Network (BRAN)

    SciTech Connect (OSTI)

    Not Available

    2003-10-01

    Helping the emerging biotechnology industry develop new tools and methods for real-time analysis of biomass feedstocks, process intermediates and The Biomass Rapid Analysis Network is designed to fast track the development of modern tools and methods for biomass analysis to accelerate the development of the emerging industry. The network will be led by industry and organized and coordinated through the National Renewable Energy Lab. The network will provide training and other activities of interest to BRAN members. BRAN members will share the cost and work of rapid analysis method development, validate the new methods, and work together to develop the training for the future biomass conversion workforce.

  6. Analysis of Cluster Management Tools

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Analysis of Configuration Management Tools Computer System, Cluster, and Networking Summer Institute Team: Evan Leeseberg, James Kang, Katherine Nystrom Mentors: Kevin Tegtmeier,...

  7. Program Direction and Analysis Jobs

    Office of Science (SC) Website

    sc-4organizationprogram-direction-and-analysis Below is a list of currently open federal employment opportunities in the Office of Science. Prospective applicants should follow...

  8. NREL: Energy Analysis - Mackay Miller

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and multilateral initiatives including the US-China Renewable Energy Partnership and 21st Century Power Partnership Quantitative social network analysis of innovation pathways...

  9. Signal Processing, Analysis, & Display

    Energy Science and Technology Software Center (OSTI)

    1986-06-01

    SIG is a general-purpose signal processing, analysis, and display program. Its main purpose is to perform manipulations on time- and frequency-domain signals. However, it has been designed to ultimately accommodate other representations for data such as multiplexed signals and complex matrices. Two user interfaces are provided in SIG - a menu mode for the unfamiliar user and a command mode for more experienced users. In both modes errors are detected as early as possible andmore » are indicated by friendly, meaningful messages. An on-line HELP package is also included. A variety of operations can be performed on time- and frequency-domain signals including operations on the samples of a signal, operations on the entire signal, and operations on two or more signals. Signal processing operations that can be performed are digital filtering (median, Bessel, Butterworth, and Chebychev), ensemble average, resample, auto and cross spectral density, transfer function and impulse response, trend removal, convolution, Fourier transform and inverse window functions (Hamming, Kaiser-Bessel), simulation (ramp, sine, pulsetrain, random), and read/write signals. User definable signal processing algorithms are also featured. SIG has many options including multiple commands per line, command files with arguments,commenting lines, defining commands, and automatic execution for each item in a repeat sequence. Graphical operations on signals and spectra include: x-y plots of time signals; real, imaginary, magnitude, and phase plots of spectra; scaling of spectra for continuous or discrete domain; cursor zoom; families of curves; and multiple viewports.« less

  10. Sandia Infrared Analysis Program

    Energy Science and Technology Software Center (OSTI)

    2004-05-11

    SandIR is a sophisticated Windows2000/WindowsXP program for the capture and analysis of thermal images in real time. It is a 32-bit, 5 thread C++ OOP application that rests on Microsoft’s MFC and DirectDraw libraries, the DT3152LS driver functions and the LabEngine link libraries of Origin 4.1 for full functionality. Images may be loaded in from saved files or viewed live by connection to a FLIR (Inframetrics) 600 or 760 IR camera or a video cassettemore » recorder playing tapes recorded from a FLIR (Inframetrlcs) 600 or 760 IR camera- At this time, no other IR camera formats are supported. The raw radiosity data used by SandiR is derived from the 8-bit, 256 level, RS-170 (grayscale) NTSC camera signal. The FLIR camera images contain 175x131 pixels of real IR data. SandIR displays these data in a 604x410 image. The maximum matrix size is 640x452 Including VIR and grayscale. Live IR images can be frozen and then stored to computer disk. An incrementing save command makes It easy to save a sequence of images with a series of related file names. These files can then be loaded into SandIR at a later time for anatysis by a number of predefined tools or data probes. Multiple pseudo-color palettes containing 64 colors are available as well as a 256 level grayscale palette for image colorizing. SandtR always processes all the data in the ROt for each acquired image; so a complete temperature matrix is always available for any frozen image. SandIR performs nearly 7 million temperature calculations per second and updates the image display through Direct Draw over the PCI bus at frequencies of 30 Hz. 3-d surface plots, projections, wire maps or contour plots of absolute temperatures are also updated at 20 to 30 Hz which approaches the real-time acquisition rate of the camera, These plots may be viewed full-screen or frozen in separate windows for comparison to later images. The full set of both 2-d and 3-d Origin plotting tools can be used to manipulate the attached plots. M plots can be manually rescaled. As, Origin script window can be used to send text commands directly to the Origin graphics server. This allows any of the SandIR plots to be formatted using the full power and capabilities of Origin. A section tool is provided to dissector cleave the surface plots. The options button in the Origin 3-d toolbar can be used to enhance the plotting resolution, which defaults to 24x16 when In surveillance mode, Note, higher resolutions slow the plot update rate and are best used for frozen images. The program provides an extensive range of tools, which can be applied to static images loaded from disk as well as live images. Tools used on live images display and update in real time with temperature data overlaid on the image itself. Active spot and area tools may be selected for temporal plotting using acquisition time intervals in the range of 33 ms to 1 hour. Temporal data are plotted on a scrolling strlpchart and can be recorded to an ascii or Excel file. Analysis tools include: Spot temperature tools to display the temperature at a set point in the image; Cursor probe to display the temperature under the tip of the mouse Line tools to be used as graphic objects or rulers, or to display the temperature profile along the line in a separate xy graphic window; On-screen profile tools, which superimpose the display of a temperature profile over the image itself; Rectangle, ellipse and polygon tools to be used as graphic objects, to display the maximum, minimum and mean temperatures within the region; Annotation tool to identify points in the image and make notations on the Image; Selector tool used to move or delete one of the above analysis tools.« less

  11. Text analysis devices, articles of manufacture, and text analysis methods

    DOE Patents [OSTI]

    Turner, Alan E; Hetzler, Elizabeth G; Nakamura, Grant C

    2013-05-28

    Text analysis devices, articles of manufacture, and text analysis methods are described according to some aspects. In one aspect, a text analysis device includes processing circuitry configured to analyze initial text to generate a measurement basis usable in analysis of subsequent text, wherein the measurement basis comprises a plurality of measurement features from the initial text, a plurality of dimension anchors from the initial text and a plurality of associations of the measurement features with the dimension anchors, and wherein the processing circuitry is configured to access a viewpoint indicative of a perspective of interest of a user with respect to the analysis of the subsequent text, and wherein the processing circuitry is configured to use the viewpoint to generate the measurement basis.

  12. Analysis Activities at Idaho National Engineering & Environmental...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Activities at Idaho National Engineering & Environmental Laboratory Analysis Activities at Idaho National Engineering & Environmental Laboratory Presentation on INEENL's analysis...

  13. Southeast European Regional Electricity Market Analysis | Open...

    Open Energy Info (EERE)

    National Laboratory Partner United States Agency for International Development, Montgomery Watson Harza Sector Energy Topics Market analysis, Background analysis Website...

  14. Analysis of Geothermal Reservoir Stimulation Using Geomechanics...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Stochastic Analysis of Injection-induced Seismicity; 2010 Geothermal ... Stochastic Analysis of Injection-induced Seismicity; 2010 Geothermal ...

  15. Technoeconomic Analysis of Photoelectrochemical (PEC) Hydrogen...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Analysis of Photoelectrochemical (PEC) Hydrogen Production Technoeconomic Analysis of Photoelectrochemical (PEC) Hydrogen Production This report documents the engineering and cost...

  16. VCAT: Visual Crosswalk Analysis Tool

    SciTech Connect (OSTI)

    Cleland, Timothy J.; Forslund, David W.; Cleland, Catherine A.

    2012-08-31

    VCAT is a knowledge modeling and analysis tool. It was synthesized from ideas in functional analysis, business process modeling, and complex network science. VCAT discovers synergies by analyzing natural language descriptions. Specifically, it creates visual analytic perspectives that capture intended organization structures, then overlays the serendipitous relationships that point to potential synergies within an organization or across multiple organizations.

  17. The principal component analysis method used with polynomial Chaos expansion to propagate uncertainties through critical transport problems

    SciTech Connect (OSTI)

    Rising, M. E.; Prinja, A. K.

    2012-07-01

    A critical neutron transport problem with random material properties is introduced. The total cross section and the average neutron multiplicity are assumed to be uncertain, characterized by the mean and variance with a log-normal distribution. The average neutron multiplicity and the total cross section are assumed to be uncorrected and the material properties for differing materials are also assumed to be uncorrected. The principal component analysis method is used to decompose the covariance matrix into eigenvalues and eigenvectors and then 'realizations' of the material properties can be computed. A simple Monte Carlo brute force sampling of the decomposed covariance matrix is employed to obtain a benchmark result for each test problem. In order to save computational time and to characterize the moments and probability density function of the multiplication factor the polynomial chaos expansion method is employed along with the stochastic collocation method. A Gauss-Hermite quadrature set is convolved into a multidimensional tensor product quadrature set and is successfully used to compute the polynomial chaos expansion coefficients of the multiplication factor. Finally, for a particular critical fuel pin assembly the appropriate number of random variables and polynomial expansion order are investigated. (authors)

  18. Miniaturized flow injection analysis system

    DOE Patents [OSTI]

    Folta, James A. (Livermore, CA)

    1997-01-01

    A chemical analysis technique known as flow injection analysis, wherein small quantities of chemical reagents and sample are intermixed and reacted within a capillary flow system and the reaction products are detected optically, electrochemically, or by other means. A highly miniaturized version of a flow injection analysis system has been fabricated utilizing microfabrication techniques common to the microelectronics industry. The microflow system uses flow capillaries formed by etching microchannels in a silicon or glass wafer followed by bonding to another wafer, commercially available microvalves bonded directly to the microflow channels, and an optical absorption detector cell formed near the capillary outlet, with light being both delivered and collected with fiber optics. The microflow system is designed mainly for analysis of liquids and currently measures 38.times.25.times.3 mm, but can be designed for gas analysis and be substantially smaller in construction.

  19. Miniaturized flow injection analysis system

    DOE Patents [OSTI]

    Folta, J.A.

    1997-07-01

    A chemical analysis technique known as flow injection analysis is described, wherein small quantities of chemical reagents and sample are intermixed and reacted within a capillary flow system and the reaction products are detected optically, electrochemically, or by other means. A highly miniaturized version of a flow injection analysis system has been fabricated utilizing microfabrication techniques common to the microelectronics industry. The microflow system uses flow capillaries formed by etching microchannels in a silicon or glass wafer followed by bonding to another wafer, commercially available microvalves bonded directly to the microflow channels, and an optical absorption detector cell formed near the capillary outlet, with light being both delivered and collected with fiber optics. The microflow system is designed mainly for analysis of liquids and currently measures 38{times}25{times}3 mm, but can be designed for gas analysis and be substantially smaller in construction. 9 figs.

  20. SYNTHESIS OF SAFETY ANALYSIS AND FIRE HAZARD ANALYSIS METHODOLOGIES

    SciTech Connect (OSTI)

    Coutts, D

    2007-04-17

    Successful implementation of both the nuclear safety program and fire protection program is best accomplished using a coordinated process that relies on sound technical approaches. When systematically prepared, the documented safety analysis (DSA) and fire hazard analysis (FHA) can present a consistent technical basis that streamlines implementation. If not coordinated, the DSA and FHA can present inconsistent conclusions, which can create unnecessary confusion and can promulgate a negative safety perception. This paper will compare the scope, purpose, and analysis techniques for DSAs and FHAs. It will also consolidate several lessons-learned papers on this topic, which were prepared in the 1990s.