Powered by Deep Web Technologies
Note: This page contains sample records for the topic "load serving entity" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Definition: Load-Serving Entity | Open Energy Information  

Open Energy Info (EERE)

Also Known As Electricity companies, electric utility Related Terms transmission service, transmission lines, energy, Interconnected Operations Service, transmission line...

2

Modeling and analysis of unsymmetrical transformer banks serving unbalanced loads  

SciTech Connect

It is a common practice to serve combination three-phase and single-phase loads from an unsymmetrical three-phase transformer bank and a four-wire secondary. Depending upon the loads and company standards, nine different transformer connections can be considered along with either an open four wire or a quadraplex secondary. The selection of the proper connection and transformer ratings can be achieved by the correct modeling and analysis of a system consisting of an equivalent source, transformer bank, secondary, and loads. This paper develops the models for the nine transformer connections, the secondary, and the loads. A computer program has been written that allows the analysis of the system for loading and short-circuit studies. The paper includes several examples of different normal and abnormal operating conditions on some of the transformer connections.

Kersting, W.H. [New Mexico State Univ., Las Cruces, NM (United States). Coll. of Engineering; Phillips, W.H. [WH Power Consultants, Las Cruces, NM (United States)

1996-05-01T23:59:59.000Z

3

Abstract--Load serving entities (LSE) and holders of default service obligations, in restructured electricity markets, provide  

E-Print Network (OSTI)

, in restructured electricity markets, provide electricity service at regulated or contracted fixed prices while standard forward contracts and commodity derivatives. Keywords: Electricity Markets, Risk Management, Volumetric hedging, I. INTRODUCTION The introduction of competitive wholesale markets in the electricity

Oren, Shmuel S.

4

The analysis of an ungrounded Wye-Delta transformer bank serving an induction motor and single-phase lighting loads  

SciTech Connect

This paper documents the detailed analysis of the three-phase ungrounded wye-delta transformer bank serving a combination three-phase induction motor and single-phase lighting load. A 3 x 3 transfer function matrix is developed that makes it possible to determine the load line-to-line voltages with a knowledge of the primary voltages of the transformer bank. Included in the transfer function matrix are the transformer impedances, unsymmetrical secondary impedance matrix, and the impedances of the motor and single-phase lighting load.

Kersting, W.H.; Rathbun, J.S.

2000-02-01T23:59:59.000Z

5

Definition: Native Load | Open Energy Information  

Open Energy Info (EERE)

Terms Load-Serving Entity References Glossary of Terms Used in Reliability Standards An LikeLike UnlikeLike You like this.Sign Up to see what your friends like. inline...

6

Adrien Serve  

NLE Websites -- All DOE Office Websites (Extended Search)

Adrien Serve Sustainable Energy Systems Group Lawrence Berkeley National Laboratory 1 Cyclotron Road MS 90R2002 Berkeley CA 94720 Office Location: 90-2002A (510) 495-2862 AServe...

7

Entity Search and the Web of Data Centralised Entity Search Federated Entity Search P2P Entity Search Conclusions and Future Semantic and Distributed Entity Search in  

E-Print Network (OSTI)

Entity Search and the Web of Data Centralised Entity Search Federated Entity Search P2P Entity Search Conclusions and Future Semantic and Distributed Entity Search in the Web of Data Robert Neumayer/48 #12;Entity Search and the Web of Data Centralised Entity Search Federated Entity Search P2P Entity

8

Entity Name: ABC Company Entity ID:  

Gasoline and Diesel Fuel Update (EIA)

Entity Name: Entity Name: ABC Company Entity ID: 00000 Data Year: 2013 State Include or exclude pre-arranged interruptions? 1 2 3 Do you capture outage records for events that initiate outside your system (customer system that causes di 4 5 6 7 8 Point to calculation in P1782: use percentages weighted based upon the classification of the circuit. 9 10 11 12 REWORD: The percent of customers automatically reported when they have lost power? e.g. SCADA, AMI, Etc. 13 SAIDI value (w/o Major Events included) FORM EIA-861 OMB No. 1905-0129 ANNUAL ELECTRIC POWER INDUSTRY REPORT

9

Extending the entity grid with entity-specific features  

Science Conference Proceedings (OSTI)

We extend the popular entity grid representation for local coherence modeling. The grid abstracts away information about the entities it models; we add discourse prominence, named entity type and coreference features to distinguish between important ...

Micha Eisner; Eugene Charniak

2011-06-01T23:59:59.000Z

10

TAC KBP Entity Selection  

Science Conference Proceedings (OSTI)

... A few terms related to Entity Selection tend to overlap in ... that you want to search for, and hit enter. The search will result in a list of documents that ...

2012-10-17T23:59:59.000Z

11

Serve on a Committee  

Science Conference Proceedings (OSTI)

Consider serving on a committee and make a difference to your professional society. Serve on a Committee Volunteer Opportunities aocs Author authors. speakers awards call for papers committees fats global governance inform job listings member memb

12

Science Serving Sustainability  

NLE Websites -- All DOE Office Websites (Extended Search)

Science Goal 8: Science Serving Sustainability Maintaining the conditions of a building improves the health of not only the surrounding ecosystems, but also the well-being of its...

13

TAC Entity Linking by Performing Full-document Entity ...  

Science Conference Proceedings (OSTI)

... few major global economies that will see respectable GDP growth this ... entities per topic: 12 ... a request by the International Atomic Energy Agency to ...

2012-02-27T23:59:59.000Z

14

TAC Entity Linking by Performing Full-document Entity ...  

Science Conference Proceedings (OSTI)

... name from the TAC 2010 data set varies between 0 (eg, “Manhattan Institute” and ... of which one is in the entity-context space (the projection of the ...

2012-03-27T23:59:59.000Z

15

Science Serving Sustainability  

NLE Websites -- All DOE Office Websites (Extended Search)

Science Science Goal 8: Science Serving Sustainability Maintaining the conditions of a building improves the health of not only the surrounding ecosystems, but also the well-being of its occupants. Energy Conservation» Efficient Water Use & Management» High Performance Sustainable Buildings» Greening Transportation» Green Purchasing & Green Technology» Pollution Prevention» Science Serving Sustainability» ENVIRONMENTAL SUSTAINABILITY GOALS at LANL Community involvement: Andy Erickson and Duncan McBranch of LANL join John Arrowsmith of Los Alamos County to discuss the photovoltaic array collaboration with community leaders. Powered by solar: This collaboratively built model home in Los Alamos is entirely powered by a photovoltaic array field, showcasing the potential for solar-powering communities. Community involvement: A ribbon cutting ceremony marks the opening of the photovoltaic powered model home in Los Alamos County, a joint venture of LANL and the county. Engaging the surrounding communities: LANL takes opportunities to engage the surrounding communities in order to develop relationships fostering sustainable actions. Here, delegates applaud the opening of SERF which will help reduce liquid waste at LANL.

16

PUBLIC SERV COM  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

'EXEC-2009-002897 'EXEC-2009-002897 PUBLIC SERV COM 1 2/25/2009 5:00 PM February 25,2009 The Honorable Steven Chu Secretary, U. S. Department of Energy 1000 Independence Avenue, S .W. Washingon, D.C. 20585 Re: State Energy Program Assurances Dear Secretary Chu: As a condition of receiving our State's share o f the $3.1, billion funding for the S t a t e Energy Program (SEP) under the American Recovery and Renewal Act of 2009 (H.R. l)(ARRA), I am providing the following assurances. I have written to our public u t i l i t y commission and requested that it consider additional actions to promote energy efficiency, consistent with the Federal statutory language contained in H.R. 1 and its obligations to maintain just and reasonable rates, while protecting the public. As set forth in the attached letter, the Chairperson of the Public Service

17

An Evaluation of the HVAC Load Potential for Providing Load Balancing Service  

Science Conference Proceedings (OSTI)

This paper investigates the potential of providing aggregated intra-hour load balancing services using heating, ventilating, and air-conditioning (HVAC) systems. A direct-load control algorithm is presented. A temperature-priority-list method is used to dispatch the HVAC loads optimally to maintain consumer-desired indoor temperatures and load diversity. Realistic intra-hour load balancing signals were used to evaluate the operational characteristics of the HVAC load under different outdoor temperature profiles and different indoor temperature settings. The number of HVAC units needed is also investigated. Modeling results suggest that the number of HVACs needed to provide a {+-}1-MW load balancing service 24 hours a day varies significantly with baseline settings, high and low temperature settings, and the outdoor temperatures. The results demonstrate that the intra-hour load balancing service provided by HVAC loads meet the performance requirements and can become a major source of revenue for load-serving entities where the smart grid infrastructure enables direct load control over the HAVC loads.

Lu, Ning

2012-09-30T23:59:59.000Z

18

Named entity normalization in user generated content  

Science Conference Proceedings (OSTI)

Named entity recognition is important for semantically oriented retrieval tasks, such as question answering, entity retrieval, biomedical retrieval, trend detection, and event and entity tracking. In many of these tasks it is important to be able to ... Keywords: evaluation, named entities, user generated content, wikipedia

Valentin Jijkoun; Mahboob Alam Khalid; Maarten Marx; Maarten de Rijke

2008-07-01T23:59:59.000Z

19

Definition: Interruptible Load Or Interruptible Demand | Open Energy  

Open Energy Info (EERE)

Interruptible Load Or Interruptible Demand Interruptible Load Or Interruptible Demand Jump to: navigation, search Dictionary.png Interruptible Load Or Interruptible Demand Demand that the end-use customer makes available to its Load-Serving Entity via contract or agreement for curtailment.[1] View on Wikipedia Wikipedia Definition View on Reegle Reegle Definition No reegle definition available. Also Known As non-firm service Related Terms transmission lines, electricity generation, transmission line, firm transmission service, smart grid References ↑ Glossary of Terms Used in Reliability Standards An inli LikeLike UnlikeLike You like this.Sign Up to see what your friends like. ne Glossary Definition Retrieved from "http://en.openei.org/w/index.php?title=Definition:Interruptible_Load_Or_Interruptible_Demand&oldid=502615"

20

Ranking entities using web search query logs  

Science Conference Proceedings (OSTI)

Searching for entities is an emerging task in Information Retrieval for which the goal is finding well defined entities instead of documents matching the query terms. In this paper we propose a novel approach to Entity Retrieval by using Web search engine ...

Bodo Billerbeck; Gianluca Demartini; Claudiu S. Firan; Tereza Iofciu; Ralf Krestel

2010-09-01T23:59:59.000Z

Note: This page contains sample records for the topic "load serving entity" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

ATTACHMENT 12 California-Based Entity (CBE) and/or Government Entity in California  

E-Print Network (OSTI)

PON-12-502 ATTACHMENT 12 California-Based Entity (CBE) and/or Government Entity in California Requirement Pursuant to AB 2267 (Fuentes, 2008), the California Energy Commission's Public Interest Energy Research Program must give a priority to "California-based entities" (CBEs) when making awards. An entity

22

Pay-less entity consolidation: exploiting entity search user feedbacks for pay-as-you-go entity data integration  

Science Conference Proceedings (OSTI)

Linked Data consists of billions of RDF triples from hundreds of different sources on the Web. The effective construction and maintenance of links between these sources largely depend on data integration solutions that scale to the large volume and heterogeneity ... Keywords: clustering, entity consolidation, entity search, implicit user feedback, pay-as-you-go data integration

Thanh Tran; Yongtao Ma; Gong Cheng

2012-06-01T23:59:59.000Z

23

Entity set expansion in opinion documents  

Science Conference Proceedings (OSTI)

Opinion mining has been an active research area in recent years. The task is to extract opinions expressed on entities and their attributes. For example, the sentence, "I love the picture quality of Sony cameras," expresses a positive opinion on the ... Keywords: entity extraction, set expansion, text mining

Lei Zhang; Bing Liu

2011-06-01T23:59:59.000Z

24

LINDEN: linking named entities with knowledge base via semantic knowledge  

Science Conference Proceedings (OSTI)

Integrating the extracted facts with an existing knowledge base has raised an urgent need to address the problem of entity linking. Specifically, entity linking is the task to link the entity mention in text with the corresponding real world entity in ... Keywords: entity linking, fact integration, knowledge base, semantic knowledge, wikipedia

Wei Shen; Jianyong Wang; Ping Luo; Min Wang

2012-04-01T23:59:59.000Z

25

Tillamook Intergovernmental Development Entity | Open Energy Information  

Open Energy Info (EERE)

Intergovernmental Development Entity Intergovernmental Development Entity Jump to: navigation, search Name Tillamook Intergovernmental Development Entity Address Tillamook People s Utility District 1115 Pacific Avenue Place Tillamook Zip 97141 Sector Marine and Hydrokinetic Phone number 503-842-2535 Website http://www.tpud.org Region United States LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This company is listed in the Marine and Hydrokinetic Technology Database. This company is involved in the following MHK Projects: Oregon Coastal Wave Energy This article is a stub. You can help OpenEI by expanding it. Retrieved from "http://en.openei.org/w/index.php?title=Tillamook_Intergovernmental_Development_Entity&oldid=678482" Categories: Clean Energy Organizations

26

Introducing baselines for russian named entity recognition  

Science Conference Proceedings (OSTI)

Current research efforts in Named Entity Recognition deal mostly with the English language. Even though the interest in multi-language Information Extraction is growing, there are only few works reporting results for the Russian language. This paper ...

Rinat Gareev, Maksim Tkachenko, Valery Solovyev, Andrey Simanovsky, Vladimir Ivanov

2013-03-01T23:59:59.000Z

27

Sepia : semantic parsing for named entities  

E-Print Network (OSTI)

People's names, dates, locations, organizations, and various numeric expressions, collectively called Named Entities, are used to convey specific meanings to humans in the same way that identifiers and constants convey ...

Marton, Gregory A. (Gregory Adam), 1977-

2004-01-01T23:59:59.000Z

28

Towards a methodology for named entities annotation  

Science Conference Proceedings (OSTI)

Today, the named entity recognition task is considered as fundamental, but it involves some specific difficulties in terms of annotation. Those issues led us to ask the fundamental question of what the annotators should annotate and, even more important, ...

Karën Fort; Maud Ehrmann; Adeline Nazarenko

2009-08-01T23:59:59.000Z

29

Integration of Contracted Renewable Energy and Spot Market Supply to Serve  

E-Print Network (OSTI)

Integration of Contracted Renewable Energy and Spot Market Supply to Serve Flexible Loads Anthony-mail: oren@ieor.berkeley.edu). Abstract: We present a contract for integrating renewable energy supply and electricity spot markets for serving deferrable electric loads in order to mitigate renewable energy

Oren, Shmuel S.

30

Identifying comparable entities on the web  

Science Conference Proceedings (OSTI)

Web search engines are often presented with user queries that involve comparisons of real-world entities. Thus far, this interaction has typically been captured by users submitting appropriately designed keyword queries for which they are presented a ... Keywords: comparables, information extraction, query logs

Alpa Jain; Patrick Pantel

2009-11-01T23:59:59.000Z

31

Configuring load as a resource for competitive electricity markets--Review of demand response programs in the U.S. and around the world  

Science Conference Proceedings (OSTI)

The restructuring of regional and national electricity markets in the U.S. and around the world has been accompanied by numerous problems, including generation capacity shortages, transmission congestion, wholesale price volatility, and reduced system reliability. These problems have created new opportunities for technologies and business approaches that allow load serving entities and other aggregators to control and manage the load patterns of wholesale and retail end-users they serve. Demand Response Programs, once called Load Management, have re-emerged as an important element in the fine-tuning of newly restructured electricity markets. During the summers of 1999 and 2001 they played a vital role in stabilizing wholesale markets and providing a hedge against generation shortfalls throughout the U.S.A. Demand Response Programs include ''traditional'' capacity reservation and interruptible/curtailable rates programs as well as voluntary demand bidding programs offered by either Load Serving Entities (LSEs) or regional Independent System Operators (ISOs). The Lawrence Berkeley National Lab (LBNL) has been monitoring the development of new types of Demand Response Programs both in the U.S. and around the world. This paper provides a survey and overview of the technologies and program designs that make up these emerging and important new programs.

Heffner, Grayson C.

2002-09-01T23:59:59.000Z

32

AEO2011: Electric Power Projections for EMM Region - Texas Regional Entity  

Open Energy Info (EERE)

Texas Regional Entity Texas Regional Entity Dataset Summary Description This dataset comes from the Energy Information Administration (EIA), and is part of the 2011 Annual Energy Outlook Report (AEO2011). This dataset is table 73, and contains only the reference case. The data is broken down into electric power sector, cumulative planned additions,cumulative unplanned additions,cumulative retirements, end-use sector, electricity sales, net energy for load, generation by fuel type and price by service category. Source EIA Date Released April 26th, 2011 (3 years ago) Date Updated Unknown Keywords 2011 AEO EIA Electric Power projections Texas Data application/vnd.ms-excel icon AEO2011: Electric Power Projections for EMM Region - Texas Regional Entity - Reference Case (xls, 259.4 KiB)

33

A bootstrapping approach for geographic named entity annotation  

Science Conference Proceedings (OSTI)

Geographic named entities can be classified into many sub-types that are useful for applications such as information extraction and question answering. In this paper, we present a bootstrapping algorithm for the task of geographic named entity annotation. ...

Seungwoo Lee; Gary Geunbae Lee

2004-10-01T23:59:59.000Z

34

Joint extraction of entities and relations for opinion recognition  

Science Conference Proceedings (OSTI)

We present an approach for the joint extraction of entities and relations in the context of opinion recognition and analysis. We identify two types of opinion-related entities --- expressions of opinions and sources of opinions --- along with the linking ...

Yejin Choi; Eric Breck; Claire Cardie

2006-07-01T23:59:59.000Z

35

UDel: named entity recognition and reference regeneration from surface text  

Science Conference Proceedings (OSTI)

This report describes the methods and results of a system developed for the GREC Named Entity Recognition and GREC Named Entity Regeneration Challenges 2010. We explain our process of automatically annotating surface text, as well as how we use this ...

Nicole L. Sparks; Charles F. Greenbacker; Kathleen F. McCoy; Che-Yu Kuo

2010-07-01T23:59:59.000Z

36

HIPAA 2013 - 2012 Audits of Covered Entity Compliance with ...  

Science Conference Proceedings (OSTI)

... Accepted Government Auditing Standards (The Yellow Book) ... audit criteria ... 5 Page 6. Who Can Be Audited? Any Covered Entity ...

2013-05-20T23:59:59.000Z

37

Graph-based reference table construction to facilitate entity matching  

Science Conference Proceedings (OSTI)

Entity matching plays a crucial role in information integration among heterogeneous data sources, and numerous solutions have been developed. Entity resolution based on reference table has the benefits of high efficiency and being easy to update. In ... Keywords: Entity matching, Graph clustering, Reference table

Fangda Wang, Hongzhi Wang, Jianzhong Li, Hong Gao

2013-06-01T23:59:59.000Z

38

Distributional similarity vs. PU learning for entity set expansion  

Science Conference Proceedings (OSTI)

Distributional similarity is a classic technique for entity set expansion, where the system is given a set of seed entities of a particular class, and is asked to expand the set using a corpus to obtain more entities of the same class as represented ...

Xiao-Li Li; Lei Zhang; Bing Liu; See-Kiong Ng

2010-07-01T23:59:59.000Z

39

CLEAN List Serve | Open Energy Information  

Open Energy Info (EERE)

List Serve List Serve Jump to: navigation, search Home | About | Inventory | Partnerships | Capacity Building | Webinars | Reports | Events | News | List Serve CLEAN List Serve Note: The list is too big to send in a single email, so send your message to part one AND part two CLEAN List Serve Name Organization Email Adib, Rana Renewable Energy Policy Network for the 21st Century (REN21) Agbemabiese, Lawrence United Nations Environment Programme Akbar, Sameer World Bank Alers, Marcel United Nations Development Programme Ashvie, Tim Climate and Development Knowledge Network (CDKN) Barnards, Geoff Bauer, Florian Renewable Energy and Energy Efficiency Partnership (REEEP) Bazilian, Morgan United Nations Industrial Development Organization (UNIDO) Ben Fadhl, Fatma United Nations Environment Programme

40

Minority Serving Institutions | Department of Energy  

NLE Websites -- All DOE Office Websites (Extended Search)

Institutions Institutions Minority Serving Institutions Map by Matt Loveless, Department of Energy. Our Office of Minority Economic Impact works daily to tap into the talents of students and faculty attending our nation's Minority Serving Institutions. To accomplish the mission of the Department of Energy, we need the best and brightest individuals to work at and partner with the Department. We're proud of the work of our Minority Educational Institution partners, and we work to advance our partnerships daily. Minority Serving Institutions are institutions of higher education that serve minority populations. They are unique both in their missions and in their day-to-day operations. Some of these colleges and universities are located in remote regions of the country, whereas others serve urban

Note: This page contains sample records for the topic "load serving entity" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Chapter 12 - Inter-Entity Transactions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

12 12 INTER-ENTITY TRANSACTIONS 1. INTRODUCTION. a. Purpose. The chapter establishes the principles and procedures of financing and accounting for costs of work performed by one DOE office or site/facility management contractor for another, and sets forth the policy governing property transfers to and from Federal agencies. Specific accounts to be used for transfers are further identified in the Standard General Ledger Chart of Accounts and Related Codes. b. Applicability. The provisions of this chapter apply to all Departmental elements except the Federal Energy Regulatory Commission and the Power Marketing Administrations (referred to hereafter as "offices") and to all DOE site/facility management contractors (referred to hereafter as

42

Minority Serving Institutions Internship Program | National Nuclear  

NLE Websites -- All DOE Office Websites (Extended Search)

Institutions Internship Program | National Nuclear Institutions Internship Program | National Nuclear Security Administration Our Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response Recapitalizing Our Infrastructure Continuing Management Reform Countering Nuclear Terrorism About Us Our Programs Our History Who We Are Our Leadership Our Locations Budget Our Operations Media Room Congressional Testimony Fact Sheets Newsletters Press Releases Speeches Events Social Media Video Gallery Photo Gallery NNSA Archive Federal Employment Apply for Our Jobs Our Jobs Working at NNSA Blog Minority Serving Institutions Internship Program Home > Federal Employment > Apply for Our Jobs > How to Apply > Student Jobs > Minority Serving Institutions Internship Program Minority Serving Institutions Internship Program

43

Minority Serving Institutions Internship Program | National Nuclear  

National Nuclear Security Administration (NNSA)

Institutions Internship Program | National Nuclear Institutions Internship Program | National Nuclear Security Administration Our Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response Recapitalizing Our Infrastructure Continuing Management Reform Countering Nuclear Terrorism About Us Our Programs Our History Who We Are Our Leadership Our Locations Budget Our Operations Media Room Congressional Testimony Fact Sheets Newsletters Press Releases Speeches Events Social Media Video Gallery Photo Gallery NNSA Archive Federal Employment Apply for Our Jobs Our Jobs Working at NNSA Blog Minority Serving Institutions Internship Program Home > Federal Employment > Apply for Our Jobs > How to Apply > Student Jobs > Minority Serving Institutions Internship Program Minority Serving Institutions Internship Program

44

Strawberry Electric Serv Dist | Open Energy Information  

Open Energy Info (EERE)

Strawberry Electric Serv Dist Strawberry Electric Serv Dist Jump to: navigation, search Name Strawberry Electric Serv Dist Place Utah Utility Id 18206 Utility Location Yes Ownership P NERC Location WECC NERC WECC Yes Activity Transmission Yes Activity Buying Transmission Yes Activity Distribution Yes References EIA Form EIA-861 Final Data File for 2010 - File1_a[1] Energy Information Administration Form 826[2] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. Utility Rate Schedules Grid-background.png No rate schedules available. Average Rates Residential: $0.1060/kWh Commercial: $0.1170/kWh Industrial: $0.0912/kWh The following table contains monthly sales and revenue data for Strawberry Electric Serv Dist (Utah).

45

Here to Serve | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Here to Serve Here to Serve Here to Serve May 11, 2012 - 8:53am Addthis Dot Harris Dot Harris The Honorable Dot Harris, Director, Office of Economic Impact and Diversity It is a pleasure to join the Administration as the Director of the Office of Economic Impact and Diversity here at the Department of Energy. When President Obama nominated me for this position, I immediately recognized the vital importance of the work that this office does. From assisting small businesses to supporting minority serving institutions to enhancing the diversity and inclusion at the Department, this office has a mission-critical role for our clean energy future. I care deeply about my responsibilities in this position. As the Director at the Office of Economic Impact and Diversity, I'll be leading the

46

One Video Stream to Serve Diverse Receivers  

E-Print Network (OSTI)

The fundamental problem of wireless video multicast is to scalably serve multiple receivers which may have very different channel characteristics. Ideally, one would like to broadcast a single stream that allows each ...

Woo, Grace

2008-10-18T23:59:59.000Z

47

Table3_EntityReductions.xls  

U.S. Energy Information Administration (EIA) Indexed Site

Entity-Level Emission Reductions Reported, Data Year 2005 Entity-Level Emission Reductions Reported, Data Year 2005 (Metric Tons Carbon Dioxide Equivalent) Reduction Type 1991 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 2002 2003 2004 2005 Carbon Dioxide Sequestration 1,540,000 1,540,000 1,540,000 1,540,000 1,540,000 1,540,000 1,540,000 1,540,000 1,540,000 1,540,000 1,540,000 1,540,000 1,540,000 1,540,000 Carbon Dioxide Sequestration 4,150,000 4,150,000 4,150,000 4,150,000 4,150,000 4,150,000 4,150,000 4,150,000 4,150,000 4,150,000 4,150,000 4,150,000 4,150,000 Carbon Dioxide Sequestration 550,000 70,000 290,000 370,000 480,000 440,000 440,000 590,000 530,000 370,000 410,000 410,000 410,000 410,000 410,000 Carbon Dioxide Direct 1,089 38,701 44,225 41,839 41,903 39,980 41,386 Methane Indirect 2,926 15,518 30,562 31,708 20,017 21,045 21,135 Perfluoromethane Direct -211 31,151 31,344

48

DE-AC03-76SF00098. CONFIGURING LOAD AS A RESOURCE FOR COMPETITIVE ELECTRICITY MARKETS – REVIEW OF DEMAND RESPONSE PROGRAMS IN THE U.S. AND AROUND THE WORLD  

E-Print Network (OSTI)

The restructuring of regional and national electricity markets in the U.S. and around the world has been accompanied by numerous problems, including generation capacity shortages, transmission congestion, wholesale price volatility, and reduced system reliability. These problems have created new opportunities for technologies and business approaches that allow load serving entities and other aggregators to control and manage the load patterns of wholesale and retail end-users they serve. Demand Response Programs, once called Load Management, have re-emerged as an important element in the fine-tuning of newly restructured electricity markets. During the summers of 1999 and 2001 they played a vital role in stabilizing wholesale markets and providing a hedge

Grayson C. Heffner; Grayson C. Heffner

2002-01-01T23:59:59.000Z

49

Wyandotte Municipal Serv Comm | Open Energy Information  

Open Energy Info (EERE)

Wyandotte Municipal Serv Comm Wyandotte Municipal Serv Comm Place Michigan Utility Id 21048 Utility Location Yes Ownership M NERC Location RFC NERC RFC Yes Operates Generating Plant Yes Activity Generation Yes Activity Transmission Yes Activity Buying Transmission Yes Activity Distribution Yes References EIA Form EIA-861 Final Data File for 2010 - File1_a[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. Utility Rate Schedules Grid-background.png HEATING STEAM RATE Residential HOT WATER DISTRICT HEATING RATE Commercial LARGE GENERAL SERVICE RATE Commercial Commercial LARGE GENERAL SERVICE RATE Commercial (Time-Differentiated Meter) Commercial LARGE GENERAL SERVICE RATE Industrial (Time-Differentiated Meter)

50

A test collection for entity search in DBpedia  

Science Conference Proceedings (OSTI)

We develop and make publicly available an entity search test collection based on the DBpedia knowledge base. This includes a large number of queries and corresponding relevance judgments from previous benchmarking campaigns, covering a broad range of ... Keywords: dbpedia, entity retrieval, semantic search, test collections

Krisztian Balog; Robert Neumayer

2013-07-01T23:59:59.000Z

51

Classifier Ensemble Selection Using Genetic Algorithm for Named Entity Recognition  

Science Conference Proceedings (OSTI)

In this paper, we propose a classifier ensemble technique based on genetic algorithm (GA) for named entity recognition (NER). We assume that the classifiers based on different feature representations can be effectively combined together using GA to achieve ... Keywords: Classifier ensemble, Genetic algorithm, Maximum entropy, Named entity recognition, Natural language processing

Asif Ekbal; Sriparna Saha

2010-03-01T23:59:59.000Z

52

Named entity recognition in a South African context  

Science Conference Proceedings (OSTI)

The feasibility of a probabilistic Named Entity Recognition system in a South African context was tested. The intended use of the system is in a cyber forensic domain. At the core of the system is a dynamic Bayesian Network, which takes into account ... Keywords: cyber forensics, dynamic Bayesian networks, gazetteers, information extraction, named entity

Anita Louis; Alta De Waal; Cobus Venter

2006-10-01T23:59:59.000Z

53

Detecting, categorizing and clustering entity mentions in Chinese text  

Science Conference Proceedings (OSTI)

The work presented in this paper is motivated by the practical need for content extraction, and the available data source and evaluation benchmark from the ACE program. The Chinese Entity Detection and Recognition (EDR) task is of particular interest ... Keywords: entity mentions in Chinese, mention categorization and mention clustering, mention detection

Wenjie Li; Donglei Qian; Qin Lu; Chunfa Yuan

2007-07-01T23:59:59.000Z

54

Student Research Abstract: Trustworthy Remote Entities in the Smart Grid  

E-Print Network (OSTI)

Student Research Abstract: Trustworthy Remote Entities in the Smart Grid Andrew J. Paverd to enhance user privacy by introducing a novel element into the smart grid architecture. The Trustworthy a group of smart meters and the external smart grid entities. The TRE enhances user privacy by providing

Oxford, University of

55

Deemed Savings Estimates for Legacy Air Conditioning and WaterHeating Direct Load Control Programs in PJM Region  

SciTech Connect

During 2005 and 2006, the PJM Interconnection (PJM) Load Analysis Subcommittee (LAS) examined ways to reduce the costs and improve the effectiveness of its existing measurement and verification (M&V) protocols for Direct Load Control (DLC) programs. The current M&V protocol requires that a PURPA-compliant Load Research study be conducted every five years for each Load-Serving Entity (LSE). The current M&V protocol is expensive to implement and administer particularly for mature load control programs, some of which are marginally cost-effective. There was growing evidence that some LSEs were mothballing or dropping their DLC programs in lieu of incurring the expense associated with the M&V. This project had several objectives: (1) examine the potential for developing deemed savings estimates acceptable to PJM for legacy air conditioning and water heating DLC programs, and (2) explore the development of a collaborative, regional, consensus-based approach for conducting monitoring and verification of load reductions for emerging load management technologies for customers that do not have interval metering capability.

Goldman, Charles

2007-03-01T23:59:59.000Z

56

Load cell  

DOE Patents (OSTI)

A load cell combines the outputs of a plurality of strain gauges to measure components of an applied load. Combination of strain gauge outputs allows measurement of any of six load components without requiring complex machining or mechanical linkages to isolate load components. An example six axis load cell produces six independent analog outputs, each directly proportional to one of the six general load components. 16 figs.

Spletzer, B.L.

1998-12-15T23:59:59.000Z

57

Load cell  

DOE Patents (OSTI)

A load cell combines the outputs of a plurality of strain gauges to measure components of an applied load. Combination of strain gauge outputs allows measurement of any of six load components without requiring complex machining or mechanical linkages to isolate load components. An example six axis load cell produces six independent analog outputs which can be combined to determine any one of the six general load components.

Spletzer, Barry L. (Albuquerque, NM)

2001-01-01T23:59:59.000Z

58

Load cell  

DOE Patents (OSTI)

A load cell combines the outputs of a plurality of strain gauges to measure components of an applied load. Combination of strain gauge outputs allows measurement of any of six load components without requiring complex machining or mechanical linkages to isolate load components. An example six axis load cell produces six independent analog outputs, each directly proportional to one of the six general load components.

Spletzer, Barry L. (Albuquerque, NM)

1998-01-01T23:59:59.000Z

59

Energy Revolving Loan Fund - Public Entities | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Energy Revolving Loan Fund - Public Entities Energy Revolving Loan Fund - Public Entities Energy Revolving Loan Fund - Public Entities < Back Eligibility Local Government Savings Category Heating & Cooling Commercial Heating & Cooling Heating Home Weatherization Commercial Weatherization Sealing Your Home Cooling Other Design & Remodeling Windows, Doors, & Skylights Ventilation Construction Heat Pumps Appliances & Electronics Commercial Lighting Lighting Insulation Water Heating Bioenergy Solar Buying & Making Electricity Wind Maximum Rebate $2,500,000 Program Info Funding Source American Recovery and Reinvestment Act of 2009 (ARRA) State Michigan Program Type State Loan Program Rebate Amount $100,000-$2,500,000 Provider Department of Energy, Labor and Economic Growth '''''Note: Michigan Economic Development Corporation is not currently

60

YAKIMA BASIN JOINT BOARD A Partnership of Public Entities Promoting  

E-Print Network (OSTI)

YAKIMA BASIN JOINT BOARD A Partnership of Public Entities Promoting the Multiple Uses of the Yakima for the opportunity to comment. Sincerely, Jim Trull, President Yakima Basin Joint Board #12;

Note: This page contains sample records for the topic "load serving entity" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

The Importance of Markush Searching for Chemical Entities  

E-Print Network (OSTI)

• What are the patentability requirements of chemical entities? • Why search the patent and non-patent literature? • Why is structure searching essential for chemical entities? • What are the two types of structuresearchable databases for patent and non-patent literature? • How do exemplified compound databases and Markush databases differ? • What value does Markush searching provide? CAS is a division of the American Chemical Society. 2

Elaine Cheeseman Ph. D

2010-01-01T23:59:59.000Z

62

CoServ Electric Cooperative - Commercial Energy Efficient Lighting...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CoServ Electric Cooperative - Commercial Energy Efficient Lighting Rebate Program CoServ Electric Cooperative - Commercial Energy Efficient Lighting Rebate Program Eligibility...

63

Energy Efficiency Goals and Requirements for Public Entities | Department  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Energy Efficiency Goals and Requirements for Public Entities Energy Efficiency Goals and Requirements for Public Entities Energy Efficiency Goals and Requirements for Public Entities < Back Eligibility Institutional Local Government Schools State Government Savings Category Appliances & Electronics Commercial Lighting Lighting Program Info State Texas Program Type Energy Standards for Public Buildings Provider State Energy Conservation Office In 2001, Texas Senate Bill 5 ([http://www.capitol.state.tx.us/tlodocs/77R/billtext/html/SB00005F.htm S.B. 5]), was enacted to help the state comply with federal Clean Air Act standards. S.B. 5 amended the state's Health and Safety Code to require that each political subdivision in 38 (later amended to 41) Texas counties: * Implement all energy efficiency measures that meet the standards

64

Property:GRR/ActionableEntity | Open Energy Information  

Open Energy Info (EERE)

ActionableEntity ActionableEntity Jump to: navigation, search Property Name GRR/ActionableEntity Property Type Page Description The agency, party or organization associated with an action described in an element of the Geothermal Regulatory Roadmap. Subproperties This property has the following 37 subproperties: G GRR/Elements/14-CA-b.1 - NPDES Permit Application GRR/Elements/14-CA-b.10 - Did majority of RWQCB approve the permit GRR/Elements/14-CA-b.12 - Were all EPA objections resolved GRR/Elements/14-CA-b.13 - NPDES Permit issued GRR/Elements/14-CA-b.3 - Is the application complete for the Regional Water Quality Control Board GRR/Elements/14-CA-b.5 - Is the application complete for the US EPA GRR/Elements/14-CA-b.6 - Does RWQCB decide to allow discharge GRR/Elements/14-CA-b.7 - Publish public notice

65

AEO2011: Renewable Energy Generation by Fuel - Texas Regional Entity |  

Open Energy Info (EERE)

Texas Regional Entity Texas Regional Entity Dataset Summary Description This dataset comes from the Energy Information Administration (EIA), and is part of the 2011 Annual Energy Outlook Report (AEO2011). This dataset is table 98, and contains only the reference case. The dataset uses gigawatts, billion kilowatthours and quadrillion Btu. The data is broken down into generating capacity, electricity generation and energy consumption. Source EIA Date Released April 26th, 2011 (3 years ago) Date Updated Unknown Keywords 2011 AEO EIA Energy Generation Fuel Texas Data application/vnd.ms-excel icon AEO2011: Renewable Energy Generation by Fuel - Texas Regional Entity- Reference Case (xls, 118.9 KiB) Quality Metrics Level of Review Peer Reviewed Comment Temporal and Spatial Coverage Frequency Annually

66

New York Power Authority - Energy Services Programs for Public Entities |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Power Authority - Energy Services Programs for Public Power Authority - Energy Services Programs for Public Entities New York Power Authority - Energy Services Programs for Public Entities < Back Eligibility Institutional Local Government Schools Savings Category Heating & Cooling Commercial Heating & Cooling Heating Cooling Manufacturing Other Home Weatherization Commercial Weatherization Sealing Your Home Ventilation Heat Pumps Appliances & Electronics Commercial Lighting Lighting Bioenergy Solar Buying & Making Electricity Water Heating Program Info State New York Program Type State Rebate Program Rebate Amount Not Specified Provider New York Power Authority New York Power Authority (NYPA) provides energy efficiency improvements to eligible public sector organizations at no up-front cost. A range of energy

67

Fuel Cell Financing for Tax-Exempt Entities  

NLE Websites -- All DOE Office Websites (Extended Search)

Financing for Financing for Tax-Exempt Entitities Facilitating deployments by structuring energy service contracts to include the Energy Investment Tax Credit. Introduction The Energy Investment Tax Credit (ITC) 1 can help reduce the cost of installing a fuel cell system. While Department of Treasury regulations prevent tax-exempt entities, e.g., not-for-profit organiza- tions, from directly taking advantage of tax benefits for property that they own, the Internal Revenue Code (IRC) and Treasury regulations allow these entities to enter into contract-for-services agreements with private-sector project developers

68

DOE Joint Genome Institute: Trillions Served: Massive, Complex...  

NLE Websites -- All DOE Office Websites (Extended Search)

the number of burgers served has eclipsed the billion mark, while the U.S. Department of Energy (DOE) Joint Genome Institute (JGI) will now serve up trillions of nucleotides of...

69

CoServ - Solar Energy Rebate (Texas) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2W '''''NOTE: Available funding for fiscal year 2012 has been exhausted for the CoServ Solar PV Rebate Program.''''' CoServ Electric Cooperative provides a variety of "Think...

70

Generalizing from relevance feedback using named entity wildcards  

Science Conference Proceedings (OSTI)

Traditional adaptive filtering systems learn the user's interests in a rather simple way - words from relevant documents are favored in the query model, while words from irrelevant documents are down-weighted. This biases the query model towards specific ... Keywords: adaptive filtering, named entities, relevance feedback

Abhimanyu Lad; Yiming Yang

2007-11-01T23:59:59.000Z

71

Query-Independent learning to rank for RDF entity search  

Science Conference Proceedings (OSTI)

The amount of structured data is growing rapidly. Given a structured query that asks for some entities, the number of matching candidate results is often very high. The problem of ranking these results has gained attention. Because results in ... Keywords: information retrieval, learning to rank, semantic search

Lorand Dali; Blaž Fortuna; Thanh Tran Duc; Dunja Mladeni?

2012-05-01T23:59:59.000Z

72

Clique-based clustering for improving named entity recognition systems  

Science Conference Proceedings (OSTI)

We propose a system which builds, in a semi-supervised manner, a resource that aims at helping a NER system to annotate corpus-specific named entities. This system is based on a distributional approach which uses syntactic dependencies for measuring ...

Julien Ah-Pine; Guillaume Jacquet

2009-03-01T23:59:59.000Z

73

CoServ - Solar Energy Rebate (Texas) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CoServ - Solar Energy Rebate (Texas) CoServ - Solar Energy Rebate (Texas) CoServ - Solar Energy Rebate (Texas) < Back Eligibility Commercial Residential Savings Category Solar Buying & Making Electricity Maximum Rebate $5,000 Program Info Funding Source CoServ Start Date 01/01/2011 State Texas Program Type Utility Rebate Program Rebate Amount $2/W Provider CoServ Electric Cooperative '''''NOTE: Available funding for fiscal year 2012 has been exhausted for the CoServ Solar PV Rebate Program.''''' CoServ Electric Cooperative provides a variety of "Think Green Rebates" to its members, including a solar energy rebate. The solar photovoltaic (PV) system must be less than or equal to 50 kW, but the rebate is available only on the first 2.5 kW. Customers must sign an interconnection agreement

74

Federal Energy Management Program: FDA Construction Project Serves as a  

NLE Websites -- All DOE Office Websites (Extended Search)

FDA Construction FDA Construction Project Serves as a Super ESPC Model to someone by E-mail Share Federal Energy Management Program: FDA Construction Project Serves as a Super ESPC Model on Facebook Tweet about Federal Energy Management Program: FDA Construction Project Serves as a Super ESPC Model on Twitter Bookmark Federal Energy Management Program: FDA Construction Project Serves as a Super ESPC Model on Google Bookmark Federal Energy Management Program: FDA Construction Project Serves as a Super ESPC Model on Delicious Rank Federal Energy Management Program: FDA Construction Project Serves as a Super ESPC Model on Digg Find More places to share Federal Energy Management Program: FDA Construction Project Serves as a Super ESPC Model on AddThis.com... Energy Savings Performance Contracts

75

Load Control  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Visualization and Controls Peer Review Visualization and Controls Peer Review Load Control for System Reliability and Measurement-Based Stability Assessment Dan Trudnowski, PhD, PE Montana Tech Butte, MT 59701 dtrudnowski@mtech.edu 406-496-4681 October 2006 2 Presentation Outline * Introduction - Goals, Enabling technologies, Overview * Load Control - Activities, Status * Stability Assessment - Activities, Status * Wrap up - Related activities, Staff 3 Goals * Research and develop technologies to improve T&D reliability * Technologies - Real-time load control methodologies - Measurement-based stability-assessment 4 Enabling Technologies * Load control enabled by GridWise technology (e.g. PNNL's GridFriendly appliance) * Real-time stability assessment enabled by Phasor Measurement (PMU) technology 5 Project Overview * Time line: April 18, 2006 thru April 17, 2008

76

Definition: Transmission Customer | Open Energy Information  

Open Energy Info (EERE)

Load-Serving Entity, or Purchasing-Selling Entity.1 Related Terms transmission service, transmission lines, transmission line References Glossary of Terms Used in Reliability...

77

Giving Back to Those Who Served | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Giving Back to Those Who Served Giving Back to Those Who Served Giving Back to Those Who Served November 10, 2010 - 6:58pm Addthis While we officially observe Veterans Day just once a year, we remember the service of those who have worn the uniform of the United States each and every day. Tomorrow, the Department of Energy honors those who serve, nearly 2,300 of which are DOE employees. A day dedicated to love of country, willingness to serve, and willingness to sacrifice for the common good of the Nation, it is appropriate that on this Veterans Day we look for ways we can serve others. The Department, along with the rest of the Federal government, is in the midst of the 2010 Combined Federal Campaign, a fundraising drive dedicated to giving back to those in need. We know why we give. We know how fortunate we are as Federal employees, and

78

Duffy Served as EM's First Assistant Secretary | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Duffy Served as EM's First Assistant Secretary Duffy Served as EM's First Assistant Secretary Duffy Served as EM's First Assistant Secretary June 26, 2013 - 12:00pm Addthis Leo Duffy served as head of DOE's nuclear cleanup program from 1989 to 1993. Leo Duffy served as head of DOE's nuclear cleanup program from 1989 to 1993. Editor's note: In an occasional EM Update series, we feature interviews with former EM Assistant Secretaries to reflect on their achievements and challenges in the world's largest nuclear cleanup and to discuss endeavors in life after EM. More than 24 years ago, Leo Duffy became the first Assistant Secretary of DOE's Office of Environmental Restoration and Waste Management. Confirmed during President George H.W. Bush's administration, Duffy served as the head of this new mission from 1989 to 1993. That pioneering program is now

79

Duffy Served as EM's First Assistant Secretary | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Duffy Served as EM's First Assistant Secretary Duffy Served as EM's First Assistant Secretary Duffy Served as EM's First Assistant Secretary June 26, 2013 - 12:00pm Addthis Leo Duffy served as head of DOE's nuclear cleanup program from 1989 to 1993. Leo Duffy served as head of DOE's nuclear cleanup program from 1989 to 1993. Editor's note: In an occasional EM Update series, we feature interviews with former EM Assistant Secretaries to reflect on their achievements and challenges in the world's largest nuclear cleanup and to discuss endeavors in life after EM. More than 24 years ago, Leo Duffy became the first Assistant Secretary of DOE's Office of Environmental Restoration and Waste Management. Confirmed during President George H.W. Bush's administration, Duffy served as the head of this new mission from 1989 to 1993. That pioneering program is now

80

Giving Back to Those Who Served | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Giving Back to Those Who Served Giving Back to Those Who Served Giving Back to Those Who Served November 10, 2010 - 6:58pm Addthis While we officially observe Veterans Day just once a year, we remember the service of those who have worn the uniform of the United States each and every day. Tomorrow, the Department of Energy honors those who serve, nearly 2,300 of which are DOE employees. A day dedicated to love of country, willingness to serve, and willingness to sacrifice for the common good of the Nation, it is appropriate that on this Veterans Day we look for ways we can serve others. The Department, along with the rest of the Federal government, is in the midst of the 2010 Combined Federal Campaign, a fundraising drive dedicated to giving back to those in need. We know why we give. We know how fortunate we are as Federal employees, and

Note: This page contains sample records for the topic "load serving entity" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Number of Marketers Serving Residential Customers, December 2002  

U.S. Energy Information Administration (EIA)

Number of Marketers Serving Residential Customers, December 2002. State/District *Total Marketers ... Gives number of marketers but no names: Georgia: 10: 10:

82

CoServ Electric Cooperative - Commercial Energy Efficient Lighting...  

Open Energy Info (EERE)

icon Twitter icon CoServ Electric Cooperative - Commercial Energy Efficient Lighting Rebate Program (Texas) This is the approved revision of this page, as well as being...

83

Deadline Monday for Minority Serving Institutions Solar Science...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

25, 2013. The funding opportunity, which was posted February 20 by the Department's SunShot Initative, is seeking applications from Minority Serving Institutions to support...

84

Federal Energy Management Program: FDA Construction Project Serves...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Program: FDA Construction Project Serves as a Super ESPC Model on AddThis.com... Energy Savings Performance Contracts Assistance & Contacts Resources Laws & Regulations...

85

Central Illinois Pub Serv Co (Illinois) EIA Revenue and Sales...  

Open Energy Info (EERE)

navigation, search EIA Monthly Electric Utility Sales and Revenue Data for Central Illinois Pub Serv Co for December 2008. Monthly Electric Utility Sales and Revenue Data Short...

86

Central Illinois Pub Serv Co (Illinois) EIA Revenue and Sales...  

Open Energy Info (EERE)

navigation, search EIA Monthly Electric Utility Sales and Revenue Data for Central Illinois Pub Serv Co for January 2009. Monthly Electric Utility Sales and Revenue Data Short...

87

LOADING DEVICE  

DOE Patents (OSTI)

A device is presented for loading or charging bodies of fissionable material into a reactor. This device consists of a car, mounted on tracks, into which the fissionable materials may be placed at a remote area, transported to the reactor, and inserted without danger to the operating personnel. The car has mounted on it a heavily shielded magazine for holding a number of the radioactive bodies. The magazine is of a U-shaped configuration and is inclined to the horizontal plane, with a cap covering the elevated open end, and a remotely operated plunger at the lower, closed end. After the fissionable bodies are loaded in the magazine and transported to the reactor, the plunger inserts the body at the lower end of the magazine into the reactor, then is withdrawn, thereby allowing gravity to roll the remaining bodies into position for successive loading in a similar manner.

Ohlinger, L.A.

1958-10-01T23:59:59.000Z

88

Columbia Basin Water Transactions Program (Water Entity); National Fish and Wildlife Foundation, Annual Report 2003.  

DOE Green Energy (OSTI)

Launched in 2002, the Columbia Basin Water Transactions Program (CBWTP) is anticipated to be a five-year effort to test new strategies for enhancing tributary flows. The premise of the CBWTP is that water can most readily be made available for instream flows not by attempting to regulate senior water users but, instead, by acquiring water rights from willing sellers and transferring those rights to instream flows within the prior appropriation framework ('first in time, first in right'). The primary goals for this water initiative included: (1) To implement Action 151 of the NOAA Fisheries 2000 Biological Opinion on the Operation of the Federal Columbia River Power System. (2) To implement Provision A.8 of the Council's 2000 Columbia River Basin Fish and Wildlife Program related to securing water for instream flows. (3) To integrate components of the Northwest Power and Conservation Council's Program and Watershed Assessment process with the NOAA Fisheries 2000 Biological Opinion. (4) To ensure actions taken under the program would be effective, fiscally efficient, and biologically beneficial to fish and wildlife in the region. In the spring of 2002, BPA and a group of water experts selected ten local entities in Washington, Oregon, Idaho, and western Montana with a demonstrated potential to innovate and implement tributary flow improvements. We also selected the National Fish and Wildlife Foundation (NFWF) to serve as the regional entity for this initiative. BPA then set up the funding agreement and scope of work to establish what is now known as the Columbia Basin Water Transactions Program. In FY 2003, BPA provided over $1.5 million in funding to the CBWTP and approved 33 water transactions. In FY 2004, BPA will provide up to $4 million to the project to enhance habitat. Thanks to the dedicated efforts of partners throughout the Basin, the CBWTP is off to a strong start in improving tributary flows in key areas across the region.

National Fish and Wildlife Foundation

2004-02-01T23:59:59.000Z

89

CoServ Electric Cooperative - Commercial Energy Efficient Lighting Rebate  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CoServ Electric Cooperative - Commercial Energy Efficient Lighting CoServ Electric Cooperative - Commercial Energy Efficient Lighting Rebate Program CoServ Electric Cooperative - Commercial Energy Efficient Lighting Rebate Program < Back Eligibility Commercial Industrial Savings Category Appliances & Electronics Commercial Lighting Lighting Program Info Funding Source Via partnership with whole sale provider Brazos Electric Power, Inc. and escheat funds Start Date 09/01/2009 State Texas Program Type Utility Rebate Program Rebate Amount Custom Lighting Upgrade: 0.30/watt saved per fixture T8 Fluorescent Upgrade: 1.50 - 2.25/bulb per fixture Provider CoServ Electric Cooperative CoServ Electric Cooperative provides rebates for commercial and industrial customers who upgrade to high efficiency lighting for the workplace. A rebate of $0.30/watt saved is available on custom lighting upgrades and a

90

Deadline Monday for Minority Serving Institutions Solar Science Funding  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Deadline Monday for Minority Serving Institutions Solar Science Deadline Monday for Minority Serving Institutions Solar Science Funding Opportunity Application Deadline Monday for Minority Serving Institutions Solar Science Funding Opportunity Application March 21, 2013 - 4:33pm Addthis Deadline Monday for Minority Serving Institutions Solar Science Funding Opportunity Application The deadline to apply for the Diversity In Science and Technology Advances National Clean Energy in Solar (DISTANCE-SOLAR) Funding Opportunity Announcement, is this Monday, March 25, 2013. The funding opportunity, which was posted February 20 by the Department's SunShot Initative, is seeking applications from Minority Serving Institutions to support solar science and technology research to advance the development of a diverse and innovative workforce.

91

Deadline Monday for Minority Serving Institutions Solar Science Funding  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Deadline Monday for Minority Serving Institutions Solar Science Deadline Monday for Minority Serving Institutions Solar Science Funding Opportunity Application Deadline Monday for Minority Serving Institutions Solar Science Funding Opportunity Application March 21, 2013 - 4:33pm Addthis Deadline Monday for Minority Serving Institutions Solar Science Funding Opportunity Application The deadline to apply for the Diversity In Science and Technology Advances National Clean Energy in Solar (DISTANCE-SOLAR) Funding Opportunity Announcement, is this Monday, March 25, 2013. The funding opportunity, which was posted February 20 by the Department's SunShot Initative, is seeking applications from Minority Serving Institutions to support solar science and technology research to advance the development of a diverse and innovative workforce.

92

Weakly-supervised discovery of named entities using web search queries  

Science Conference Proceedings (OSTI)

A seed-based framework for textual information extraction allows for weakly supervised extraction of named entities from anonymized Web search queries. The extraction is guided by a small set of seed named entities, without any need for handcrafted extraction ... Keywords: knowledge acquisition, named entities, query logs, unstructured text, weakly supervised information extraction

Marius Pa?ca

2007-11-01T23:59:59.000Z

93

Online named entity recognition method for microtexts in social networking services: A case study of twitter  

Science Conference Proceedings (OSTI)

Named entity recognition (NER) methods have been regarded as an efficient strategy to extract relevant entities for answering a given query. The aim of this work is to exploit the conventional NER methods for analyzing a large set of microtexts of which ... Keywords: Multiplex social network, Named entity recognition, Network analysis, Social networks

Jason J. Jung

2012-07-01T23:59:59.000Z

94

Proposal for an extension of traditional named entities: from guidelines to evaluation, an overview  

Science Conference Proceedings (OSTI)

Within the framework of the construction of a fact database, we defined guidelines to extract named entities, using a taxonomy based on an extension of the usual named entities definition. We thus defined new types of entities with broader coverage including ...

Cyril Grouin; Sophie Rosset; Pierre Zweigenbaum; Karën Fort; Olivier Galibert; Ludovic Quintard

2011-06-01T23:59:59.000Z

95

Effective retrieval model for entity with multi-valued attributes: BM25MF and beyond  

Science Conference Proceedings (OSTI)

The task of entity retrieval becomes increasingly prevalent as more and more structured information about entities is available on the Web in various forms such as documents embedding metadata (RDF, RDFa, Microdata, Microformats). International benchmarking ... Keywords: BM25, BM25F, BM25MF, PL2, PL2F, PL2MF, RDF, entity retrieval, ranking, search, semi-structured data

Stéphane Campinas; Renaud Delbru; Giovanni Tummarello

2012-10-01T23:59:59.000Z

96

Minority Serving Institution Internship Program | National Nuclear Security  

NLE Websites -- All DOE Office Websites (Extended Search)

Institution Internship Program | National Nuclear Security Institution Internship Program | National Nuclear Security Administration Our Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response Recapitalizing Our Infrastructure Continuing Management Reform Countering Nuclear Terrorism About Us Our Programs Our History Who We Are Our Leadership Our Locations Budget Our Operations Media Room Congressional Testimony Fact Sheets Newsletters Press Releases Speeches Events Social Media Video Gallery Photo Gallery NNSA Archive Federal Employment Apply for Our Jobs Our Jobs Working at NNSA Blog Minority Serving Institution Internship Program Home > Federal Employment > Our Jobs > Opportunities for Students > Minority Serving Institution Internship Program Minority Serving Institution Internship Program

97

Minority Serving Institution Internship Program | National Nuclear Security  

National Nuclear Security Administration (NNSA)

Institution Internship Program | National Nuclear Security Institution Internship Program | National Nuclear Security Administration Our Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response Recapitalizing Our Infrastructure Continuing Management Reform Countering Nuclear Terrorism About Us Our Programs Our History Who We Are Our Leadership Our Locations Budget Our Operations Media Room Congressional Testimony Fact Sheets Newsletters Press Releases Speeches Events Social Media Video Gallery Photo Gallery NNSA Archive Federal Employment Apply for Our Jobs Our Jobs Working at NNSA Blog Minority Serving Institution Internship Program Home > Federal Employment > Our Jobs > Opportunities for Students > Minority Serving Institution Internship Program Minority Serving Institution Internship Program

98

LOADED WAVEGUIDES  

DOE Patents (OSTI)

>Loaded waveguides are described for the propagation of electromagnetic waves with reduced phase velocities. A rectangular waveguide is dimensioned so as to cut-off the simple H/sub 01/ mode at the operating frequency. The waveguide is capacitance loaded, so as to reduce the phase velocity of the transmitted wave, by connecting an electrical conductor between directly opposite points in the major median plane on the narrower pair of waveguide walls. This conductor may take a corrugated shape or be an aperature member, the important factor being that the electrical length of the conductor is greater than one-half wavelength at the operating frequency. Prepared for the Second U.N. International ConferThe importance of nuclear standards is duscussed. A brief review of the international callaboration in this field is given. The proposal is made to let the International Organization for Standardization (ISO) coordinate the efforts from other groups. (W.D.M.)

Mullett, L.B.; Loach, B.G.; Adams, G.L.

1958-06-24T23:59:59.000Z

99

CoServ - Solar Energy Rebate | Open Energy Information  

Open Energy Info (EERE)

Page Edit with form History Share this page on Facebook icon Twitter icon CoServ - Solar Energy Rebate This is the approved revision of this page, as well as being the most...

100

Bringing Proposal Writing Training to Faculty at Minority Serving  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Bringing Proposal Writing Training to Faculty at Minority Serving Bringing Proposal Writing Training to Faculty at Minority Serving Institutions Bringing Proposal Writing Training to Faculty at Minority Serving Institutions June 20, 2012 - 12:20pm Addthis Bringing Proposal Writing Training to Faculty at Minority Serving Institutions Bill Valdez Bill Valdez Principal Deputy Director Money doesn't grow on trees, but it does grow from developing your school and business to the point that you're ready to compete for a Department of Energy funding opportunity. Our office's mission is to make sure that the energy programs here, including our competitive funding opportunities, are accessible to minorities and historically disadvantaged communities. That's why we're hosting technical assistance workshops at events across the country, engaging students, faculty, and staff at Minority

Note: This page contains sample records for the topic "load serving entity" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Commercial Products Show Potential to serve as Nuclear Material and  

NLE Websites -- All DOE Office Websites (Extended Search)

Commercial Products Show Potential to serve as Nuclear Material and Commercial Products Show Potential to serve as Nuclear Material and Activity Monitoring Technologies | National Nuclear Security Administration Our Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response Recapitalizing Our Infrastructure Continuing Management Reform Countering Nuclear Terrorism About Us Our Programs Our History Who We Are Our Leadership Our Locations Budget Our Operations Media Room Congressional Testimony Fact Sheets Newsletters Press Releases Speeches Events Social Media Video Gallery Photo Gallery NNSA Archive Federal Employment Apply for Our Jobs Our Jobs Working at NNSA Blog Home > NNSA Blog > Commercial Products Show Potential to serve as ... Commercial Products Show Potential to serve as Nuclear Material and

102

Commercial Products Show Potential to serve as Nuclear Material and  

National Nuclear Security Administration (NNSA)

Commercial Products Show Potential to serve as Nuclear Material and Commercial Products Show Potential to serve as Nuclear Material and Activity Monitoring Technologies | National Nuclear Security Administration Our Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response Recapitalizing Our Infrastructure Continuing Management Reform Countering Nuclear Terrorism About Us Our Programs Our History Who We Are Our Leadership Our Locations Budget Our Operations Media Room Congressional Testimony Fact Sheets Newsletters Press Releases Speeches Events Social Media Video Gallery Photo Gallery NNSA Archive Federal Employment Apply for Our Jobs Our Jobs Working at NNSA Blog Home > NNSA Blog > Commercial Products Show Potential to serve as ... Commercial Products Show Potential to serve as Nuclear Material and

103

Power Choice/Pepco Energy Serv | Open Energy Information  

Open Energy Info (EERE)

Choice/Pepco Energy Serv Choice/Pepco Energy Serv Jump to: navigation, search Name Power Choice/Pepco Energy Serv Place New Jersey Utility Id 14405 References EIA Form EIA-861 Final Data File for 2010 - File2_2010[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. Utility Rate Schedules Grid-background.png No rate schedules available. Average Rates No Rates Available References ↑ "EIA Form EIA-861 Final Data File for 2010 - File2_2010" Retrieved from "http://en.openei.org/w/index.php?title=Power_Choice/Pepco_Energy_Serv&oldid=412767" Categories: EIA Utility Companies and Aliases Utility Companies Organizations Stubs What links here Related changes Special pages Printable version

104

Bringing Proposal Writing Training to Faculty at Minority Serving  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Bringing Proposal Writing Training to Faculty at Minority Serving Bringing Proposal Writing Training to Faculty at Minority Serving Institutions Bringing Proposal Writing Training to Faculty at Minority Serving Institutions June 20, 2012 - 12:20pm Addthis Bringing Proposal Writing Training to Faculty at Minority Serving Institutions Bill Valdez Bill Valdez Principal Deputy Director Money doesn't grow on trees, but it does grow from developing your school and business to the point that you're ready to compete for a Department of Energy funding opportunity. Our office's mission is to make sure that the energy programs here, including our competitive funding opportunities, are accessible to minorities and historically disadvantaged communities. That's why we're hosting technical assistance workshops at events across the country, engaging students, faculty, and staff at Minority

105

CoServ Electric Cooperative- Residential Energy Efficiency Rebate Program  

Energy.gov (U.S. Department of Energy (DOE))

CoServ Electric Cooperative's "Think Green Rebate Program" provides a range of incentives encouraging its residential customers to upgrade to high efficiency equipment in their homes. Rebates are...

106

Join our Webinar for Minority Serving Institutions on Science Education  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Join our Webinar for Minority Serving Institutions on Science Join our Webinar for Minority Serving Institutions on Science Education Opportunities This Monday Join our Webinar for Minority Serving Institutions on Science Education Opportunities This Monday December 13, 2012 - 9:19am Addthis Faculty and Students - Check out these Office of Science opportunities before they close by listening in on our webinar: Monday, December 17, at 1pm EST. Faculty and Students - Check out these Office of Science opportunities before they close by listening in on our webinar: Monday, December 17, at 1pm EST. Annie Whatley Annie Whatley Deputy Director, Office of Minority Economic Impact You're Invited: Faculty and Students at Minority Serving Institutions (MSIs) are invited to participate in an Energy Department webinar on Monday, December 17, 2012,

107

Minority Serving Institution Technical Consortium Model | Department of  

NLE Websites -- All DOE Office Websites (Extended Search)

Minority Serving Institution Technical Consortium Model Minority Serving Institution Technical Consortium Model Minority Serving Institution Technical Consortium Model In October 2012, the National Nuclear Security Administration (NNSA) awarded $4 million in grants to 22 Historically Black Colleges and Universities (HBCUs) in key STEM areas. This funding launched NNSA's new Minority Serving Institution Partnership Program, a consortium program organized to build a sustainable STEM pipeline between six Energy Department plants and laboratories and the HBCUs. The Program is designed to enrich the STEM capabilities of HBCUs in a sustainable manner that aligns with the broad interests of Energy Department sites and emphasizes the STEM career pipeline. The program brings together 8 teams from HBCUs that share similar interests

108

Denton County Electric Cooperative d/b/a CoServ Electric Smart Grid Project  

Open Energy Info (EERE)

d/b/a CoServ Electric Smart Grid Project d/b/a CoServ Electric Smart Grid Project Jump to: navigation, search Project Lead Denton County Electric Cooperative d/b/a CoServ Electric Country United States Headquarters Location Corinth, Texas Recovery Act Funding $17,205,844.00 Total Project Value $40,966,296.00 Coverage Area Coverage Map: Denton County Electric Cooperative d/b/a CoServ Electric Smart Grid Project Coordinates 33.1540091°, -97.0647322° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[]}

109

Public Serv Comm of Yazoo City | Open Energy Information  

Open Energy Info (EERE)

Serv Comm of Yazoo City Serv Comm of Yazoo City Jump to: navigation, search Name Public Serv Comm of Yazoo City Place Mississippi Utility Id 21095 Utility Location Yes Ownership P NERC Location SERC NERC SERC Yes NERC SPP Yes RTO SPP Yes Operates Generating Plant Yes Activity Generation Yes Activity Distribution Yes Activity Bundled Services Yes References EIA Form EIA-861 Final Data File for 2010 - File1_a[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. Utility Rate Schedules Grid-background.png Electric - City Commercial Electric - PSC Commercial Electric - Schools Commercial Electric Commercial - Large Commercial Electric Commercial - Seasonal Commercial Electric Commercial - Small Commercial

110

South Carolina Pub Serv Auth | Open Energy Information  

Open Energy Info (EERE)

Pub Serv Auth Pub Serv Auth Jump to: navigation, search Name South Carolina Pub Serv Auth Place South Carolina Utility Id 17543 Utility Location Yes Ownership S NERC Location SERC NERC SERC Yes Operates Generating Plant Yes Activity Generation Yes Activity Transmission Yes Activity Buying Transmission Yes Activity Distribution Yes Activity Wholesale Marketing Yes Alt Fuel Vehicle Yes Alt Fuel Vehicle2 Yes References EIA Form EIA-861 Final Data File for 2010 - File1_a[1] Energy Information Administration Form 826[2] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. Utility Rate Schedules Grid-background.png GA-12(General Service) Commercial GB-12 (Medium General Service) Commercial

111

Rebate Program Serves Alaskans with Disabilities | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Serves Alaskans with Disabilities Serves Alaskans with Disabilities Rebate Program Serves Alaskans with Disabilities July 21, 2010 - 2:10pm Addthis Lorelei Laird Writer, Energy Empowers What are the key facts? Energy efficient appliances are made more affordable in rural Alaska thanks to $500 rebates. With rates of up to .50 kWh in Alaska, energy efficient appliances reduce energy bills. Alaska applies Recovery Act funding to lower administrative costs of their rebate program. According to the U.S. Census Population Finder, the estimated population of Alaska as of 2009 was 698,473. In the same year, Alaska was awarded $658,000 as part of the State Appliance Rebate Program, an American Recovery and Reinvestment Act program that helps Americans purchase ENERGY STAR appliances to replace older, inefficient models. That grant worked out

112

A Minority Serving Institution Leads the Way in Better Buildings |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

A Minority Serving Institution Leads the Way in Better Buildings A Minority Serving Institution Leads the Way in Better Buildings A Minority Serving Institution Leads the Way in Better Buildings July 5, 2012 - 6:06pm Addthis Secretary Chu visits Delaware State University to commemorate the school's efforts with the Better Buildings Initiative. Secretary Chu visits Delaware State University to commemorate the school's efforts with the Better Buildings Initiative. Dot Harris Dot Harris The Honorable Dot Harris, Director, Office of Economic Impact and Diversity In February 2011, President Obama announced the Better Buildings Initiative to make commercial and industrial buildings 20 percent more energy efficient by 2020 and accelerate private sector investment in energy efficiency. Delaware State University (DSU) was selected as one of the

113

Central Vermont Pub Serv Corp | Open Energy Information  

Open Energy Info (EERE)

Pub Serv Corp Pub Serv Corp Jump to: navigation, search Name Central Vermont Pub Serv Corp Place Vermont Service Territory Vermont Website www.cvps.com Green Button Reference Page www.efficiencyvermont.com Green Button Committed Yes Utility Id 3292 Utility Location Yes Ownership I NERC Location NPCC NERC NPCC Yes ISO NE Yes Operates Generating Plant Yes Activity Generation Yes Activity Transmission Yes Activity Distribution Yes Activity Wholesale Marketing Yes Alt Fuel Vehicle Yes Alt Fuel Vehicle2 Yes References EIA Form EIA-861 Final Data File for 2010 - File1_a[1] Energy Information Administration Form 826[2] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. Utility Rate Schedules

114

The use of intelligence information to identify the foreign interests of entities involved with DOE programs  

SciTech Connect

This report investigates whether DOE activities could benefit from greater and more consistent access to intelligence information on selected entities with foreign interests. It does not cover dual-use and munition commodities. The investigation determined what information was available from the national intelligence community and law enforcement agencies that would have prevented DOE contracts with selected entities if the information had been available and regulations regarding contracts with selected entities had been enforced.

Not Available

1993-10-22T23:59:59.000Z

115

New Castle Municipal Serv Comm | Open Energy Information  

Open Energy Info (EERE)

New Castle Municipal Serv Comm New Castle Municipal Serv Comm Place Delaware Utility Id 13424 Utility Location Yes Ownership M NERC Location RFC NERC RFC Yes Activity Distribution Yes References EIA Form EIA-861 Final Data File for 2010 - File1_a[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. Utility Rate Schedules Grid-background.png Commercial Space Heating (Grandfathered) Commercial Large General Service Commercial Demand Rate (Primary) Commercial Large General Service Commercial Demand Rate (Secondary) Commercial Medium General Service Commercial Demand Rate Commercial Residential Service Residential Residential Space Heating Residential Small General Service Commercial Non-Demand Rate Commercial

116

and could possibly serve as a repository for  

NLE Websites -- All DOE Office Websites (Extended Search)

and could possibly serve as a repository for and could possibly serve as a repository for captured CO 2 emissions. The formation is covered by layers of low permeability rock and possesses several properties that are conducive to CO 2 storage, such as the appropriate depth, thickness, porosity, and permeability. Prior to drilling the test well, MRCSP conducted a seismic survey at the site and obtained necessary permits for the injection test from the U.S. Environmental Protection Agency (EPA) and the Kentucky Division of Oil and Gas. Following the permitting process, the researchers injected clean brine in order to determine formation properties like the maximum injection rate and then injected approximately 1,000 metric tons of CO 2 in two, 500-meter-ton steps. The injection rate, pressure, temperature,

117

Creating suites of models with system entity structure: global warming example  

Science Conference Proceedings (OSTI)

We describe how to develop a suite of models in the MS4 Modeling Environment. The approach employs the operation of merging of System Entity Structures supported by the environment. After construction, the suite of models can be hosted on Model Store, ... Keywords: component-based modeling, suite of models, system entity structure, systems of systems

Bernard P. Zeigler, Chungman Seo, Robert Coop, Doohwan Kim

2013-04-01T23:59:59.000Z

118

Domain-independent data cleaning via analysis of entity-relationship graph  

Science Conference Proceedings (OSTI)

In this article, we address the problem of reference disambiguation. Specifically, we consider a situation where entities in the database are referred to using descriptions (e.g., a set of instantiated attributes). The objective of reference disambiguation ... Keywords: Connection strength, RelDC, data cleaning, entity resolution, graph analysis, reference disambiguation, relationship analysis

Dmitri V. Kalashnikov; Sharad Mehrotra

2006-06-01T23:59:59.000Z

119

Exploring phrasal context and error correction heuristics in bootstrapping for geographic named entity annotation  

Science Conference Proceedings (OSTI)

Geographic named entities can be classified into many sub-types that are useful for applications such as information extraction and question answering. In this paper, we present a high-performance bootstrapping algorithm with error correction heuristics ... Keywords: Bootstrapping, Error correcting heuristics, Geographic named entity annotation, Location normalization, Phrasal context

Seungwoo Lee; Gary Geunbae Lee

2007-06-01T23:59:59.000Z

120

Web personal name disambiguation based on reference entity tables mined from the web  

Science Conference Proceedings (OSTI)

Ambiguous personal names are common on the Web, which pose a challenge for many different tasks. The traditional disambiguation employs the clustering methods. However, without reference entity tables, the clustering method can only identify whether ... Keywords: name disambiguation, named entity disambiguation, person resolution, web person search

Xianpei Han; Jun Zhao

2009-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "load serving entity" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Entity-relationship and object-oriented formalisms for modeling spatial environmental data  

Science Conference Proceedings (OSTI)

Entity-Relationship (ER) and Object-Oriented (OO) formalisms are often used to model environmental information of databases or computer programs. The majority of the environmental information is georeferenced. However, for 20 years, researchers have ... Keywords: Entity-relationship formalism, Environmental data, Geographic information system, Object-oriented design, Software engineering

François Pinet

2012-07-01T23:59:59.000Z

122

1995 Pacific Northwest Loads and Resources Study.  

Science Conference Proceedings (OSTI)

The study establishes the planning basis for supplying electricity to customers. The study presents projections of regional and Federal system load and resource capabilities, and serves as a benchmark for annual BPA determinations made pursuant to the 1981 regional power sales contracts.

United States. Bonneville Power Administration.

1995-12-01T23:59:59.000Z

123

How well do home energy audits serve the homeowner?  

NLE Websites -- All DOE Office Websites (Extended Search)

How well do home energy audits serve the homeowner? How well do home energy audits serve the homeowner? Title How well do home energy audits serve the homeowner? Publication Type Conference Proceedings LBNL Report Number LBNL-5712E Year of Publication 2012 Authors Ingle, Aaron, Mithra M. Moezzi, Loren Lutzenhiser, and Richard C. Diamond Conference Name 2012 Summer Study on Energy Efficiency in Buildings Date Published 05/2012 Conference Location Pacific Grove, CA, USA Abstract Home energy audits administered by utilities and government typically provide homeowners with lists of technical upgrade recommendations intended to increase the technical energy efficiency of the house. Audits proceed with assessment of physical characteristics, subsequently processed with a computational model and transformed into a report, sometimes customized by the auditor. While the design of an energy audit reflects program and policy points of view - balancing program cost with expected program savings, educating people about the value of energy efficiency, etc. - it is crucial to consider the criteria for a good home energy audit and recommendations from homeowners' points of view. How well do home energy audits currently meet these criteria? How well do asset-based assessments match what homeowners seem to want? We consider these questions based on a study of 286 homeowners who participated in a Seattle City Light home energy audit program. Findings suggest that there is substantial opportunity to reorient audit programs to better fit the realities of why homeowners undertake energy audits and retrofits. In the Seattle City Light program, participating homeowners found certain elements of the audit they received - interaction with professional auditors, blower door testing, and customized, specific upgrade recommendations - to be more compelling than the standardized and quantitative elements. Rather than being engaged with increasing energy efficiency, as invited by an asset perspective and asset-based efficiency scores, homeowners wanted to build better understanding of their home's energy use and to learn how to solve specific problems, especially reflecting their household's actual energy use practices.

124

Periodic load balancing  

Science Conference Proceedings (OSTI)

Multiprocessor load balancing aims to improve performance by moving jobs from highly loaded processors to more lightly loaded processors. Some schemes allow only migration of new jobs upon arrival, while other schemes allow migration of ... Keywords: heavy traffic diffusion approximations, load balancing, periodic load balancing, reflected Brownian motion, resource sharing, transient behavior

Gísli Hjálmtýsson; Ward Whitt

1998-06-01T23:59:59.000Z

125

DOE Joint Genome Institute: Adaptable Button Mushroom Serves Up  

NLE Websites -- All DOE Office Websites (Extended Search)

8, 2012 8, 2012 Adaptable Button Mushroom Serves Up Biomass-Degrading Genes Critical to Managing the Planet's Carbon Stores The button mushroom occupies a prominent place in our diet and in the grocery store where it boasts a tasty multibillion-dollar niche, while in nature, Agaricus bisporus is known to decay leaf matter on the forest floor. Now, owing to an international collaboration of two-dozen institutions led by the French National Institute for Agricultural Research (INRA) and the U.S. Department of Energy Joint Genome Institute (DOE JGI), the full repertoire of A. bisporus genes has been determined. In particular, new work shows how its genes are actually deployed not only in leaf decay but also wood decay and in the development of fruiting bodies (the above ground part of the mushroom harvested for food). The work also

126

Northern Indiana Pub Serv Co | Open Energy Information  

Open Energy Info (EERE)

Co Co Jump to: navigation, search Name Northern Indiana Pub Serv Co Place Indiana Utility Id 13756 Utility Location Yes Ownership I NERC Location RFC NERC RFC Yes ISO MISO Yes Operates Generating Plant Yes Activity Generation Yes Activity Transmission Yes Activity Buying Transmission Yes Activity Distribution Yes Activity Wholesale Marketing Yes Activity Bundled Services Yes Alt Fuel Vehicle Yes Alt Fuel Vehicle2 Yes References EIA Form EIA-861 Final Data File for 2010 - File1_a[1] Energy Information Administration Form 826[2] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. Utility Rate Schedules Grid-background.png Adjustment of Charges for Cost of Fuel Rider Adjustment of Charges for Regional Transmission Organization

127

Application of association rules mining to Named Entity Recognition and co-reference resolution for the Indonesian language  

Science Conference Proceedings (OSTI)

In this paper, we propose a new method, association rules mining for Named Entity Recognition (NER) and co-reference resolution. The method uses several morphological and lexical features such as Pronoun Class (PC) and Name Class ... Keywords: Indonesia, Indonesian language, NER, association rules mining, co-reference resolution, data mining, entity equivalence, information extraction, information retrieval, named entity recognition

Indra Budi; Stephane Bressan

2007-12-01T23:59:59.000Z

128

USDA Webinar: Value-Added Producer Grants for Tribal Entities | Department  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

USDA Webinar: Value-Added Producer Grants for Tribal Entities USDA Webinar: Value-Added Producer Grants for Tribal Entities USDA Webinar: Value-Added Producer Grants for Tribal Entities January 14, 2014 11:00AM to 12:30PM MST Webinar Sponsored by the U.S. Department of Agriculture (USDA) Rural Development, this tribal-specific training will provide an overview of the FY14 Funding Opportunity and the Value-Added Producer Grants (VAPG) program and provide information about tribal entity eligibility and documentation requirements. Prospective tribal applicants, technical assistance providers, and interested USDA field staff will find the information helpful. Conference Call Information: Toll-free number: +1 800-981-3173 Toll number for DC area: +1 202-720-7039 Participant code: 4248 Join the LiveMeeting Webinar here. For more information, contact Tedd Buelow at 720-544-2911.

129

USDA Webinar: Value-Added Producer Grants for Tribal Entities | Department  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

USDA Webinar: Value-Added Producer Grants for Tribal Entities USDA Webinar: Value-Added Producer Grants for Tribal Entities USDA Webinar: Value-Added Producer Grants for Tribal Entities January 14, 2014 1:00PM EST FY2014 Training Schedule Tuesday, January 14 9:00 - 10:30 AM Alaska Standard Time 10:00 - 11:30 AM Pacific Standard Time 11:00 AM-12:30 PM Mountain Standard Time 12:00 PM - 1:30 PM Central Standard Time 1:00 PM-2:30 PM Eastern Standard Time Topics: FY 14 Funding Opportunity, overview of VAPG program, tribal entity eligibility and documentation requirements. Who should attend: Prospective Tribal applicants, technical assistance providers, interested USDA field staff. Conference Call Information: Toll-free number: +1 800-981-3173 Toll number for DC area: +1 202-720-7039 Participant code: 4248 Join the LiveMeeting Webinar here:

130

Analyzing entities and topics in news articles using statistical topic models  

Science Conference Proceedings (OSTI)

Statistical language models can learn relationships between topics discussed in a document collection and persons, organizations and places mentioned in each document. We present a novel combination of statistical topic models and named-entity recognizers ...

David Newman; Chaitanya Chemudugunta; Padhraic Smyth; Mark Steyvers

2006-05-01T23:59:59.000Z

131

Building Energy Software Tools Directory: HAP System Design Load  

NLE Websites -- All DOE Office Websites (Extended Search)

HAP System Design Load HAP System Design Load HAP System Design Load logo. Provides the load estimating and system design features found in its popular cousin � Carrier�s Hourly Analysis Program (HAP). By focusing on system design features, the HAP System Design Load program serves as a simpler, more efficient tool for those users only interested in system design; energy simulation features are omitted. Like the HAP program, HAP System Design Load provides the ease of use of a Windows-based graphical user interface and the computing power of modern 32-bit software. HAP System Design Load uses a system-based approach to HVAC load estimating. This approach tailors sizing procedures and results to the specific type of system being considered. A wide variety of equipment types

132

Battery loading device  

SciTech Connect

A battery loading device for loading a power source battery, built in small appliances having a battery loading chamber for selectively loading a number of cylindrical unit batteries or a one body type battery having the same voltage as a number of cylindrical unit batteries, whereby the one body type battery and the battery loading chamber are shaped similarly and asymmetrically in order to prevent the one body type battery from being inserted in the wrong direction.

Phara, T.; Suzuki, M.

1984-08-28T23:59:59.000Z

133

FINAL PROJECT REPORT LOAD MODELING TRANSMISSION RESEARCH  

E-Print Network (OSTI)

composition: The total load profile obtained from  load individual load types if  load profiles of individual load composition validation: Load profiles generated by the load 

Lesieutre, Bernard

2013-01-01T23:59:59.000Z

134

Water and energy conservation system for food serving establishments  

SciTech Connect

A water and energy conserving apparatus is described for supplying pre-heated water to a hot water heater and for cooling at least one refrigeration unit using a compressible medium in a food serving establishment comprising, a pre-heater tank adapted to receive water from a cold water source and having a cold water inlet line connected to the cold water source and a cold water outlet line. A heat exchanger which is associated with the refrigeration unit is connected to the cold water output line coming from the tank. A hot water output line is connected between the heat exchanger and the tank for returning water from the heat exchanger to the tank. The compressible medium which is hot is supplied from the refrigeration unit to the heat exchanger and the water flowing through the heat exchanger cools the compressible medium thus picking up heat. A circulator is connected into the hot water output line for circulating water from the tank to the heat exchanger and back. A drain line is connected to the heated water output line and includes a normally closed solenoid valve. The drain line is connected to a drain and is provided to vent water from the pre-heater tank. A thermostat is connected to the cold water output line coming from the tank to sense the temperature. The thermostat is connected to a power supply which powers the solenoid and when the temperature of water in the cold water output line rises above a selected value, which is preferably in the vicinity of 85 degrees Fahrenheit, the solenoid valve is energized to open the flow of water in the drain line and vent water from the pre-heater tank. A pre-heater water line is connected between the pre-heater tank and the hot water heater to supply pre-heated water to the hot water heater to conserve energy used in heating the otherwise cold water normally supplied to the hot water heater.

Papadakos, J.

1981-01-27T23:59:59.000Z

135

Load sensing system  

DOE Patents (OSTI)

A load sensing system inexpensively monitors the weight and temperature of stored nuclear material for long periods of time in widely variable environments. The system can include an electrostatic load cell that encodes weight and temperature into a digital signal which is sent to a remote monitor via a coaxial cable. The same cable is used to supply the load cell with power. When multiple load cells are used, vast

Sohns, Carl W. (Oak Ridge, TN); Nodine, Robert N. (Knoxville, TN); Wallace, Steven Allen (Knoxville, TN)

1999-01-01T23:59:59.000Z

136

Discharge circuits and loads  

SciTech Connect

This will be an overview in which some of the general properties of loads are examined: their interface with the energy storage and switching devices; general problems encountered with different types of loads; how load behavior and fault modes can impact on the design of a power conditioning system (PCS).

Sarjeant, W.J.

1980-10-15T23:59:59.000Z

137

PROGRESS REPORT ON RESOURCE ADEQUACY  

E-Print Network (OSTI)

................................................................. 82 No-Load LSEs (Entities Not Serving Any Electrical Loads).................................. 83 City Procurement as a Share of Forecasted Non-Coincident Peak Load (Percent)......................................................................................... 27 Table 3: LADWP Procurement Shares of Forecasted Peak Load (Percent)............ 29 Table 4: SMUD

138

On loading rate effects in toughening processes  

SciTech Connect

Environmental crack tip reactions are a known source of premature fracture in oxides. These rate-dependent phenomena commonly are studied in strength tests where loading rate serves as the major experimental variable. A material susceptible to environmentally-assisted crack growth is stronger at fast testing rates. A topic which has received far less attention is the influence of stressing rate or loading rate on the shielding processes which occur at some distance from the crack tip, although the inverse has been studied by Deuerler et al. The authors present here the first known documentation of a loading rate effect on shielding phenomena in ceramic materials. For these experiments Coors AD 94 alumina was chosen for study.

Tandon, S.; Faber, K.T. [Northwestern Univ., Evanston, IL (United States)

1996-03-01T23:59:59.000Z

139

WHAT THE SMART GRID MEANS TO YOU AND THE PEOPLE YOU SERVE | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

WHAT THE SMART GRID MEANS TO YOU AND THE PEOPLE YOU SERVE WHAT THE SMART GRID MEANS TO YOU AND THE PEOPLE YOU SERVE The U.S. Department of Energy (DOE) is charged under the Energy...

140

WHAT THE SMART GRID MEANS TO YOU AND THE PEOPLE YOU SERVE | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

SERVE WHAT THE SMART GRID MEANS TO YOU AND THE PEOPLE YOU SERVE The U.S. Department of Energy (DOE) is charged under the Energy Independence and Security Act of 2007 (EISA 2007)...

Note: This page contains sample records for the topic "load serving entity" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Load Management - A Better Way  

E-Print Network (OSTI)

Ohio Edison Company serves about 800,000 customers in Ohio and Pennsylvania, making it one of the 20 largest electric utilities in the nation. The 'cost of service' concept has been basic to rate design throughout the history of the company, and is evident today as the demand related charges have escalated in recent rate cases reflecting the higher costs of installing new generating facilities at today's high construction and financing costs. This paper will describe one of the many applications of load management techniques which has enabled the company to shift well over 100,000 kilowatts of customer load from the on-peak period to the off-peak period in the last four to five years. This is helping delay the need for new plants and allows existing plants to be more fully utilized, resulting in lower costs to customers who use their electric service wisely and possibly lower rate increases in the future than would have been required otherwise.

Easley, J. F.

1982-01-01T23:59:59.000Z

142

D-Dupe: An Interactive Tool for Entity Resolution in Social Networks Mustafa Bilgic  

E-Print Network (OSTI)

entity resolution result. We illustrate and evaluate the benefits of D-Dupe on three bibliographic on a portion of the InfoVis data set. (a) shows the initial network before any resolutions have been performed-Dupe on bibliographic collab- oration networks. However D-Dupe's layout and interaction princi- ples are general and can

Shneiderman, Ben

143

A Lazy Learning Model for Entity Linking Using Query-Specific Information  

E-Print Network (OSTI)

Azerbaijan, or other entries in KB that have the same name. Most previous studies on entity linking used: {c1: state of Arizona, c2: Azerbaijan, ..., cN : Alitalia}, automatically creating the labeled set Aq; 48th State; AZ (U.S. state); The Copper State; Arizona, United States; ... c2 Azerbaijan

Tan, Chew Lim

144

A real time Named Entity Recognition system for Arabic text mining  

Science Conference Proceedings (OSTI)

Arabic is the most widely spoken language in the Arab World. Most people of the Islamic World understand the Classic Arabic language because it is the language of the Qur'an. Despite the fact that in the last decade the number of Arabic Internet users ... Keywords: Arabic language, Event detection, Morphological analysis, Named Entity Recognition, Root extraction, Text mining

Harith Al-Jumaily; Paloma Martínez; José L. Martínez-Fernández; Erik Goot

2012-12-01T23:59:59.000Z

145

Unsupervised gene/protein named entity normalization using automatically extracted dictionaries  

Science Conference Proceedings (OSTI)

Gene and protein named-entity recognition (NER) and normalization is often treated as a two-step process. While the first step, NER, has received considerable attention over the last few years, normalization has received much less attention. We have ...

Aaron M. Cohen

2005-06-01T23:59:59.000Z

146

March 23, 2008 DB:EER Model 1 ENHANCED ENTITY-RELATIONSHIP (EER)  

E-Print Network (OSTI)

March 23, 2008 DB:EER Model 1 ENHANCED ENTITY-RELATIONSHIP (EER) MODEL #12;March 23, 2008 DB:EER Model 2 - Objectives Introduction to EER Modeling + Concepts of the EER Model + Specialization Object Modeling + #12;March 23, 2008 DB:EER Model 3 - Introduction to EER Model Since the late 1970

Adam, Salah

147

Electrical and Production Load Factors  

E-Print Network (OSTI)

Load factors are an important simplification of electrical energy use data and depend on the ratio of average demand to peak demand. Based on operating hours of a facility they serve as an important benchmarking tool for the industrial sector. The operating hours of small and medium sized manufacturing facilities are analyzed to identify the most common operating hour or shift work patterns. About 75% of manufacturing facilities fall into expected operating hour patterns with operating hours near 40, 80, 120 and 168 hours/week. Two types of load factors, electrical and production are computed for each shift classification within major industry categories in the U.S. The load factor based on monthly billing hours (ELF) increases with operating hours from about 0.4 for a nominal one shift operation, to about 0.7 for around-the-clock operation. On the other hand, the load factor based on production hours (PLF) shows an inverse trend, varying from about 1.4 for one shift operation to 0.7 for around-the-clock operation. When used as a diagnostic tool, if the PLF exceeds unity, then unnecessary energy consumption may be taking place. For plants operating at 40 hours per week, the ELF value was found to greater than the theoretical maximum, while the PLF value was greater than one, suggesting that these facilities may have significant energy usage outside production hours. The data for the PLF however, is more scattered for plants operating less than 80 hours per week, indicating that grouping PLF data based on operating hours may not be a reasonable approach to benchmarking energy use in industries. This analysis uses annual electricity consumption and demand along with operating hour data of manufacturing plants available in the U.S. Department of Energy’s Industrial Assessment Center (IAC) database. The annual values are used because more desirable monthly data are not available. Monthly data are preferred as they capture the load profile of the facility more accurately. The data there come from Industrial Assessment Centers which employ university engineering students, faculty and staff to perform energy assessments for small to medium-sized manufacturing plants. The nation-wide IAC program is sponsored by the U.S. Department of Energy.

Sen, Tapajyoti

2009-12-01T23:59:59.000Z

148

Load sensing system  

DOE Patents (OSTI)

A load sensing system inexpensively monitors the weight and temperature of stored nuclear material for long periods of time in widely variable environments. The system can include an electrostatic load cell that encodes weight and temperature into a digital signal which is sent to a remote monitor via a coaxial cable. The same cable is used to supply the load cell with power. When multiple load cells are used, vast inventories of stored nuclear material can be continuously monitored and inventoried of minimal cost. 4 figs.

Sohns, C.W.; Nodine, R.N.; Wallace, S.A.

1999-05-04T23:59:59.000Z

149

Entity State  

U.S. Energy Information Administration (EIA) Indexed Site

13,786 1,653 11.99 City of Rushmore - (MN) MN Public 213 2,194 232 10.57 City of Saint Peter MN Public 4,108 94,946 10,164 10.71 City of Sauk Centre- (MN) MN Public 2,411 63,964...

150

Entity State  

Gasoline and Diesel Fuel Update (EIA)

Consumers Sales (megawatthours) Revenue (thousand dollars) Average Retail Price (centskWh) 3 Phases Renewables CA Power Marketer 119 1,122 65 5.79 Commerce Energy, Inc. CA Power...

151

Entity State  

U.S. Energy Information Administration (EIA) Indexed Site

Consumers Sales (megawatthours) Revenue (thousand dollars) Average Retail Price (centskWh) 3 Phases Renewables CA Power Marketer 153 35,958 1,999 5.56 Calpine Power America LLC...

152

The challenge of virginia banks: an evaluation of named entity analysis in a 19th-century newspaper collection  

Science Conference Proceedings (OSTI)

This paper evaluates automatic extraction of ten named entity classes from a 19th century newspaper, the Civil War years of the Richmond Times Dispatch, digitized with IMLS support by the University of Richmond. This paper analyzes success with ... Keywords: digital libraries, historical newspapers, named entity recognition

Gregory Crane; Alison Jones

2006-06-01T23:59:59.000Z

153

Explicit spatial scattering for load balancing in conservatively synchronized parallel discrete-event simulations  

SciTech Connect

We re-examine the problem of load balancing in conservatively synchronized parallel, discrete-event simulations executed on high-performance computing clusters, focusing on simulations where computational and messaging load tend to be spatially clustered. Such domains are frequently characterized by the presence of geographic 'hot-spots' - regions that generate significantly more simulation events than others. Examples of such domains include simulation of urban regions, transportation networks and networks where interaction between entities is often constrained by physical proximity. Noting that in conservatively synchronized parallel simulations, the speed of execution of the simulation is determined by the slowest (i.e most heavily loaded) simulation process, we study different partitioning strategies in achieving equitable processor-load distribution in domains with spatially clustered load. In particular, we study the effectiveness of partitioning via spatial scattering to achieve optimal load balance. In this partitioning technique, nearby entities are explicitly assigned to different processors, thereby scattering the load across the cluster. This is motivated by two observations, namely, (i) since load is spatially clustered, spatial scattering should, intuitively, spread the load across the compute cluster, and (ii) in parallel simulations, equitable distribution of CPU load is a greater determinant of execution speed than message passing overhead. Through large-scale simulation experiments - both of abstracted and real simulation models - we observe that scatter partitioning, even with its greatly increased messaging overhead, significantly outperforms more conventional spatial partitioning techniques that seek to reduce messaging overhead. Further, even if hot-spots change over the course of the simulation, if the underlying feature of spatial clustering is retained, load continues to be balanced with spatial scattering leading us to the observation that spatial scattering can often obviate the need for dynamic load balancing.

Thulasidasan, Sunil [Los Alamos National Laboratory; Kasiviswanathan, Shiva [Los Alamos National Laboratory; Eidenbenz, Stephan [Los Alamos National Laboratory; Romero, Philip [Los Alamos National Laboratory

2010-01-01T23:59:59.000Z

154

Explicit spatial scattering for load balancing in conservatively synchronized parallel discrete-event simulations  

SciTech Connect

We re-examine the problem of load balancing in conservatively synchronized parallel, discrete-event simulations executed on high-performance computing clusters, focusing on simulations where computational and messaging load tend to be spatially clustered. Such domains are frequently characterized by the presence of geographic 'hot-spots' - regions that generate significantly more simulation events than others. Examples of such domains include simulation of urban regions, transportation networks and networks where interaction between entities is often constrained by physical proximity. Noting that in conservatively synchronized parallel simulations, the speed of execution of the simulation is determined by the slowest (i.e most heavily loaded) simulation process, we study different partitioning strategies in achieving equitable processor-load distribution in domains with spatially clustered load. In particular, we study the effectiveness of partitioning via spatial scattering to achieve optimal load balance. In this partitioning technique, nearby entities are explicitly assigned to different processors, thereby scattering the load across the cluster. This is motivated by two observations, namely, (i) since load is spatially clustered, spatial scattering should, intuitively, spread the load across the compute cluster, and (ii) in parallel simulations, equitable distribution of CPU load is a greater determinant of execution speed than message passing overhead. Through large-scale simulation experiments - both of abstracted and real simulation models - we observe that scatter partitioning, even with its greatly increased messaging overhead, significantly outperforms more conventional spatial partitioning techniques that seek to reduce messaging overhead. Further, even if hot-spots change over the course of the simulation, if the underlying feature of spatial clustering is retained, load continues to be balanced with spatial scattering leading us to the observation that spatial scattering can often obviate the need for dynamic load balancing.

Thulasidasan, Sunil [Los Alamos National Laboratory; Kasiviswanathan, Shiva [Los Alamos National Laboratory; Eidenbenz, Stephan [Los Alamos National Laboratory; Romero, Philip [Los Alamos National Laboratory

2010-01-01T23:59:59.000Z

155

Structural load combinations  

SciTech Connect

This paper presents the latest results of the program entitled, ''Probability Based Load Combinations For Design of Category I Structures''. In FY 85, a probability-based reliability analysis method has been developed to evaluate safety of shear wall structures. The shear walls are analyzed using stick models with beam elements and may be subjected to dead load, live load and in-plane eqrthquake. Both shear and flexure limit states are defined analytically. The limit state probabilities can be evaluated on the basis of these limit states. Utilizing the reliability analysis method mentioned above, load combinations for the design of shear wall structures have been established. The proposed design criteria are in the load and resistance factor design (LRFD) format. In this study, the resistance factors for shear and flexure and load factors for dead and live loads are preassigned, while the load factor for SSE is determined for a specified target limit state probability of 1.0 x 10/sup -6/ or 1.0 x 10/sup -5/ during a lifetime of 40 years. 23 refs., 9 tabs.

Hwang, H.; Reich, M.; Ellingwood, B.; Shinozuka, M.

1985-01-01T23:59:59.000Z

156

Watershed Mercury Loading Framework  

Science Conference Proceedings (OSTI)

This report explains and illustrates a simplified stochastic framework, the Watershed Mercury Loading Framework, for organizing and framing site-specific knowledge and information on mercury loading to waterbodies. The framework permits explicit treatment of data uncertainties. This report will be useful to EPRI members, state and federal regulatory agencies, and watershed stakeholders concerned with mercury-related human and ecological health risk.

2003-05-23T23:59:59.000Z

157

load | OpenEI  

Open Energy Info (EERE)

load load Dataset Summary Description This dataset contains hourly load profile data for 16 commercial building types (based off the DOE commercial reference building models) and residential buildings (based off the Building America House Simulation Protocols). This dataset also includes the Residential Energy Consumption Survey (RECS) for statistical references of building types by location. Source Commercial and Residential Reference Building Models Date Released April 18th, 2013 (9 months ago) Date Updated July 02nd, 2013 (7 months ago) Keywords building building demand building load Commercial data demand Energy Consumption energy data hourly kWh load profiles Residential Data Quality Metrics Level of Review Some Review Comment Temporal and Spatial Coverage Frequency Annually

158

Load-management decision  

Science Conference Proceedings (OSTI)

Utilities require baseload, intermediate, and peaking plants to meet fluctuating customer demand. These can be supplemented with off-peak generation and storage and load management, which can take the form of direct utility control over interruptible and deferrable customers or customer incentives that require off-peak demand. Utilities should make a careful analysis of their load profile, their generation mix, their ability to shift loads, and customer attitudes before deciding on a load-management program that fits their individual needs. They should also be aware that load management is only a limited resource with a number of uncertainties. Research programs into customer relations, system reliability, communications devices, and special control switches and meters will help to relieve some of the uncertainties. (DCK)

Lihach, N.; Gupta, P.

1982-05-01T23:59:59.000Z

159

Biological named entity recognition using n-grams and classification methods  

E-Print Network (OSTI)

We propose a biological named entity recognition system which uses classification methods and a n-gram model to annotate terms in text. A novel method is presented to express lexical features in a pattern notation. Prefix and suffix characters are used instead of lists of potential terms or other external resources. Creating classification exemplars is conducted from text by using a word n-gram model. We evaluate our system based on the GE-NIA version 3.02 corpus which contains 2,000 paper abstracts. The system obtains an 0.705 F-score on exact match term performance. Biological concept markers are also assigned to each located term indicating its meaning. Our system retains simplicity and generalizability. Key words: Biological named entity recognition, information extraction, word n-gram, and classification algorithms 1

Sittichai Jiampojamarn; Nick Cercone

2005-01-01T23:59:59.000Z

160

Automated Population of Cyc: Extracting Information about Named-entities from the Web  

E-Print Network (OSTI)

Populating the Cyc Knowledge Base (KB) has been a manual process until very recently. However, there is currently enough knowledge in Cyc for it to be feasible to attempt to acquire additional knowledge autonomously. This paper describes a system that can collect and validate formally represented, fully-integrated knowledge from the Web or any other electronically available text corpus, about various entities of interest (e.g. famous people, organizations, etc.). Experimental results and lessons learned from their analysis are presented.

Purvesh Shah; David Schneider; Cynthia Matuszek; Robert C. Kahlert; Bjørn Aldag; David Baxter; John Cabral; Michael Witbrock; Jon Curtis

2006-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "load serving entity" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

DiffServ node with join minimum cost queue policy and multiclass traffic  

Science Conference Proceedings (OSTI)

DiffServ, the vehicle for providing relative QoS in the Internet is also easily amenable to simple and effective pricing mechanisms. By pricing access to a relative QoS, we can model a DiffServ node as a 'Join Minimum Cost Queue' in which an arriving ... Keywords: diffServ, finite buffer queues, join minimum cost queue, join shortest queue, network pricing, quasi-birth--death processes, queue control

Rahul Tandra; N. Hemachandra; D. Manjunath

2004-01-01T23:59:59.000Z

162

An efficient load model for analyzing demand side management impacts  

SciTech Connect

The main objective of implementing Demand Side Management (DSM) in power systems is to change the utility's load shape--i.e. changes in the time pattern and magnitude of utility's load. Changing the load shape as a result of demand side activities could change the peak load, base load and/or energy demand. Those three variables have to be explicitly modeled into the load curve for properly representing the effects of demand side management. The impact of DSM will be manifested as higher or lower reliability levels. This paper presents an efficient technique to model the system load such that the impact of demand side management on the power system can be easily and accurately evaluated. The proposed technique to model the load duration curve will facilitate the representation of DSM impacts on loss-of-load probability, energy not served and energy consumption. This will provide an analytical method to study the impact of DSM on capacity requirements. So far iterative methods have been applied to study these impacts. The proposed analytical method results in a faster solution with higher accuracy. It takes only 18 seconds on an 80486 PC to solve each case study involving different peak and base loads, and energy use.

Rahman, S.; Rinaldy (Virginia Polytechnic Inst. and State Univ., Blacksburg, VA (United States))

1993-08-01T23:59:59.000Z

163

Estimates of Renewable Energy Capacity Serving U.S. Green Power...  

NLE Websites -- All DOE Office Websites (Extended Search)

Estimates of Renewable Energy Capacity Serving U.S. Green Power Markets (as of December 2004) Lori Bird and Blair Swezey National Renewable Energy Laboratory September 2005 This...

164

Denton County Electric Cooperative d/b/a CoServ Electric Smart...  

Open Energy Info (EERE)

throughout CoServ Electric's service territory and explores the application of distribution automation and customer systems. The project is aimed at improving customer...

165

HLW Glass Waste Loadings  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

HLW HLW Glass Waste Loadings Ian L. Pegg Vitreous State Laboratory The Catholic University of America Washington, DC Overview Overview  Vitrification - general background  Joule heated ceramic melter (JHCM) technology  Factors affecting waste loadings  Waste loading requirements and projections  WTP DWPF  DWPF  Yucca Mountain License Application requirements on waste loading  Summary Vitrification  Immobilization of waste by conversion into a glass  Internationally accepted treatment for HLW  Why glass?  Amorphous material - able to incorporate a wide spectrum of elements over wide ranges of composition; resistant to radiation damage  Long-term durability - natural analogs Relatively simple process - amenable to nuclearization at large  Relatively simple process - amenable to nuclearization at large scale  There

166

OpenEI - load  

Open Energy Info (EERE)

are given by a location defined by the Typical Meteorological Year (TMY) for which the weather data was collected. Commercial load data is sorted by the (TMY) site as a...

167

building load data | OpenEI Community  

Open Energy Info (EERE)

building load data commercial load data dataset datasets electric load data load data load profile OpenEI residential load TMY3 United States Load data Image source: NREL...

168

electric load data | OpenEI Community  

Open Energy Info (EERE)

building load data commercial load data dataset datasets electric load data load data load profile OpenEI residential load TMY3 United States Load data Image source: NREL...

169

commercial load | OpenEI Community  

Open Energy Info (EERE)

building load data commercial load data dataset datasets electric load data load data load profile OpenEI residential load TMY3 United States Load data Image source: NREL...

170

residential load | OpenEI Community  

Open Energy Info (EERE)

building load data commercial load data dataset datasets electric load data load data load profile OpenEI residential load TMY3 United States Load data Image source: NREL...

171

Composite Load Model Evaluation  

Science Conference Proceedings (OSTI)

The WECC load modeling task force has dedicated its effort in the past few years to develop a composite load model that can represent behaviors of different end-user components. The modeling structure of the composite load model is recommended by the WECC load modeling task force. GE Energy has implemented this composite load model with a new function CMPLDW in its power system simulation software package, PSLF. For the last several years, Bonneville Power Administration (BPA) has taken the lead and collaborated with GE Energy to develop the new composite load model. Pacific Northwest National Laboratory (PNNL) and BPA joint force and conducted the evaluation of the CMPLDW and test its parameter settings to make sure that: • the model initializes properly, • all the parameter settings are functioning, and • the simulation results are as expected. The PNNL effort focused on testing the CMPLDW in a 4-bus system. An exhaustive testing on each parameter setting has been performed to guarantee each setting works. This report is a summary of the PNNL testing results and conclusions.

Lu, Ning; Qiao, Hong (Amy)

2007-09-30T23:59:59.000Z

172

Analysis of industrial load management  

SciTech Connect

Industrial Load Management, ILM, has increased the possibilities of changing load profiles and raising load factors. This paper reports on load profile measurements and feasible load management applications that could be implemented in industry e.g. bivalent systems for heating of premises and processes, load priority systems, energy storage and rescheduling processes or parts of processes due to differential electricity rates. Industrial load variations on hourly, daily and seasonal basis are treated as well as the impact by load management on load curves e g peak clipping, valley filling and increased off-peak electricity usage.

Bjork, C.O.; Karlsson, B.G.

1986-04-01T23:59:59.000Z

173

He says, she says, pat says, Tricia says: how much reference resolution matters for entity extraction, relation extraction, and social network analysis  

Science Conference Proceedings (OSTI)

Anaphora resolution (AR) identifies the entities that pronouns refer to. Coreference resolution (CR) associates the various instances of an entity with each other. Given our data, our findings suggest that deduplicating and normalizing text data by using ...

Jana Diesner; Kathleen M. Carley

2009-07-01T23:59:59.000Z

174

Distribution substation load impacts of residential air conditioner load control  

SciTech Connect

An ongoing experiment to monitor the substation level load impacts of end-use load control is described. An overview of the data acquisition system, experimental procedures and analysis techniques are provided. Results of the 1983 and 1984 experiments demonstrate the value of aggregate load impact monitoring as a means of verifying load research results, calculating the diversity of end-use loads, and predicting the impacts of load management on the transmission and distribution systems.

Heffner, G.C.; Kaufman, D.A.

1985-07-01T23:59:59.000Z

175

Harry Black Mr. Harry Black currently serves as the Director of Finance for the City of  

E-Print Network (OSTI)

Harry Black Mr. Harry Black currently serves as the Director of Finance for the City of Baltimore of Risk Management. Mr. Black has served as: Executive Vice President & COO of Global Commerce Solutions. Mr. Black is the author of "Achieving Economic Development Success: Tools that work," a nuts

Noakes, David R.

176

Consistent-degradation macroblock grouping for parallel video streams over DiffServ networks  

Science Conference Proceedings (OSTI)

This paper presents a consistent-degradation macroblock grouping scheme for improving loss resilience of parallel video streams over a two-class DiffServ network. By jointly exploiting the H.264 flexible macroblock ordering (FMO) tool, a multi-stream ... Keywords: DiffServ network, Flexible macroblock ordering, Loss resilience, Parallel video streams, Transmission distortion

Hao Liu; HaiQin Xu; ShuGuang Zhao

2012-01-01T23:59:59.000Z

177

Load Monitoring CEC/LMTF Load Research Program  

SciTech Connect

This white paper addresses the needs, options, current practices of load monitoring. Recommendations on load monitoring applications and future directions are also presented.

Huang, Zhenyu; Lesieutre, B.; Yang, Steve; Ellis, A.; Meklin, A.; Wong, B.; Gaikwad, A.; Brooks, D.; Hammerstrom, Donald J.; Phillips, John; Kosterev, Dmitry; Hoffman, M.; Ciniglio, O.; Hartwell, R.; Pourbeik, P.; Maitra, A.; Lu, Ning

2007-11-30T23:59:59.000Z

178

Demand or Request: Will Load Behave?  

Science Conference Proceedings (OSTI)

Power planning engineers are trained to design an electric system that satisfies predicted electrical demand under stringent conditions of availability and power quality. Like responsible custodians, we plan for the provision of electrical sustenance and shelter to those in whose care regulators have given us the responsibility to serve. Though most customers accept this nurturing gladly, a growing number are concerned with the economic costs and environmental impacts of service at a time when technology (particularly distributed generation, storage, automation, and information networks) offers alternatives for localized control and competitive service. As customers’ and their systems mature, a new relationship with the electricity provider is emerging. Demand response is perhaps the first unsteady step where the customer participates as a partner in system operations. This paper explores issues system planners need to consider as demand response matures to significant levels beyond direct load control and toward a situation where service is requested and bargains are reached with the electricity provider based on desired load behavior. On one hand, predicting load growth and behavior appears more daunting than ever. On the other, for the first time load becomes a new resource whose behavior can be influenced during system operations to balance system conditions.

Widergren, Steven E.

2009-07-30T23:59:59.000Z

179

SYSPLAN. Load Leveling Battery System Costs  

SciTech Connect

SYSPLAN evaluates capital investment in customer side of the meter load leveling battery systems. Such systems reduce the customer`s monthly electrical demand charge by reducing the maximum power load supplied by the utility during the customer`s peak demand. System equipment consists of a large array of batteries, a current converter, and balance of plant equipment and facilities required to support the battery and converter system. The system is installed on the customer`s side of the meter and controlled and operated by the customer. Its economic feasibility depends largely on the customer`s load profile. Load shape requirements, utility rate structures, and battery equipment cost and performance data serve as bases for determining whether a load leveling battery system is economically feasible for a particular installation. Life-cycle costs for system hardware include all costs associated with the purchase, installation, and operation of battery, converter, and balance of plant facilities and equipment. The SYSPLAN spreadsheet software is specifically designed to evaluate these costs and the reduced demand charge benefits; it completes a 20 year period life cycle cost analysis based on the battery system description and cost data. A built-in sensitivity analysis routine is also included for key battery cost parameters. The life cycle cost analysis spreadsheet is augmented by a system sizing routine to help users identify load leveling system size requirements for their facilities. The optional XSIZE system sizing spreadsheet which is included can be used to identify a range of battery system sizes that might be economically attractive. XSIZE output consisting of system operating requirements can then be passed by the temporary file SIZE to the main SYSPLAN spreadsheet.

Hostick, C.J. [Pacific Northwest Lab., Richland, WA (United States)

1988-03-22T23:59:59.000Z

180

Ocean Viruses: Tiny entities with Global Impacts ( JGI Seventh Annual User Meeting 2012: Genomics of Energy and Environment)  

Science Conference Proceedings (OSTI)

Matt Sullivan from the University of Arizona on "Ocean Viruses: Tiny Entities with Global Impacts" at the 7th Annual Genomics of Energy & Environment Meeting on March 22, 2012 in Walnut Creek, Calif.

Sullivan, Matthew B [University of Arizona

2012-03-22T23:59:59.000Z

Note: This page contains sample records for the topic "load serving entity" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Annual Report of the Columbia River Treaty, Canadian and United States Entities, October 1, 1995--September 30, 1996.  

DOE Green Energy (OSTI)

Agreements approved by the Entities during the period of this report include: (1) Columbia River Treaty Entity Agreement on the Detailed Operating Plan for Columbia River Storage for 1 August 1995 through 31 July 1996, signed 31 January 1996. (2) Columbia River Treaty Entity Agreement on the Detailed Operating Plan for Columbia River Storage for 1 August 1996 through 31 July 1997, signed 29 August 1996. (3) Columbia River Treaty Entity Agreement on Resolving the Dispute on Critical Period Determination, the Capacity Entitlement for the 1998/99, 1999/00, and 2000/01 AOP/DDPB`s, and Operating Procedures for the 2001/02 and Future AOP`s, signed 29 August 1996.

Columbia River Treaty Operating Committee; B.C. Hydro; United States. Bonneville Power Administration

1996-11-01T23:59:59.000Z

182

Mass-Loaded Flows  

E-Print Network (OSTI)

A key process within astronomy is the exchange of mass, momentum, and energy between diffuse plasmas in many types of astronomical sources (including planetary nebulae, wind-blown bubbles, supernova remnants, starburst superwinds, and the intracluster medium) and dense, embedded clouds or clumps. This transfer affects the large scale flows of the diffuse plasmas as well as the evolution of the clumps. I review our current understanding of mass-injection processes, and examine intermediate-scale structure and the global effect of mass-loading on a flow. I then discuss mass-loading in a variety of diffuse sources.

J. M. Pittard

2006-07-13T23:59:59.000Z

183

Cooling load estimation methods  

DOE Green Energy (OSTI)

Ongoing research on quantifying the cooling loads in residential buildings, particularly buildings with passive solar heating systems, is described. Correlations are described that permit auxiliary cooling estimates from monthly average insolation and weather data. The objective of the research is to develop a simple analysis method, useful early in design, to estimate the annual cooling energy required of a given building.

McFarland, R.D.

1984-01-01T23:59:59.000Z

184

LOADING AND UNLOADING DEVICE  

DOE Patents (OSTI)

A device for loading and unloading fuel rods into and from a reactor tank through an access hole includes parallel links carrying a gripper. These links enable the gripper to go through the access hole and then to be moved laterally from the axis of the access hole to the various locations of the fuel rods in the reactor tank.

Treshow, M.

1960-08-16T23:59:59.000Z

185

Multidimensional spectral load balancing  

DOE Patents (OSTI)

A method of and apparatus for graph partitioning involving the use of a plurality of eigenvectors of the Laplacian matrix of the graph of the problem for which load balancing is desired. The invention is particularly useful for optimizing parallel computer processing of a problem and for minimizing total pathway lengths of integrated circuits in the design stage.

Hendrickson, Bruce A. (Albuquerque, NM); Leland, Robert W. (Albuquerque, NM)

1996-12-24T23:59:59.000Z

186

Buildings Stock Load Control  

E-Print Network (OSTI)

Researchers and practitioners have proposed a variety of solutions to reduce electricity consumption and curtail peak demand. This research focuses on electricity demand control by applying some strategies in existing building to reduce it during the extreme climate period. The first part of this paper presents the objectives of the study: ? to restrict the startup polluting manufacturing units (power station), ? to limit the environmental impacts (greenhouse emission), ? to reduce the transport and distribution electricity infrastructures The second part presents the approach used to rise the objectives : ? To aggregat the individual loads and to analyze the impact of different strategies from load shedding to reduce peak power demand by: ? Developing models of tertiary buildings stocks (Schools, offices, Shops, hotels); ? Making simulations for different load shedding strategies to calculate potential peak power saving. The third part is dedicated to the description of the developed models: An assembly of the various blocks of the library of simbad and simulink permit to model building. Finally the last part prensents the study results: Graphs and tables to see the load shedding strategies impacts.

Joutey, H. A.; Vaezi-Nejad, H.; Clemoncon, B.; Rosenstein, F.

2006-01-01T23:59:59.000Z

187

OpenEI Community - load data  

Open Energy Info (EERE)

building load data commercial load data dataset datasets electric load data load data load profile OpenEI residential load TMY3 United States Utility Rate OpenEI Community...

188

OpenEI Community - electric load data  

Open Energy Info (EERE)

building load data commercial load data dataset datasets electric load data load data load profile OpenEI residential load TMY3 United States Utility Rate OpenEI Community...

189

OpenEI Community - building load  

Open Energy Info (EERE)

building load data commercial load data dataset datasets electric load data load data load profile OpenEI residential load TMY3 United States Utility Rate OpenEI Community...

190

OpenEI Community - residential load  

Open Energy Info (EERE)

building load data commercial load data dataset datasets electric load data load data load profile OpenEI residential load TMY3 United States Utility Rate OpenEI Community...

191

OpenEI Community - commercial load  

Open Energy Info (EERE)

building load data commercial load data dataset datasets electric load data load data load profile OpenEI residential load TMY3 United States Utility Rate OpenEI Community...

192

OpenEI Community - building load data  

Open Energy Info (EERE)

building load data commercial load data dataset datasets electric load data load data load profile OpenEI residential load TMY3 United States Utility Rate OpenEI Community...

193

EM Employee Serves Military in Afghanistan, Manages $5.8 Billion Army Task  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Employee Serves Military in Afghanistan, Manages $5.8 Billion Employee Serves Military in Afghanistan, Manages $5.8 Billion Army Task Order EM Employee Serves Military in Afghanistan, Manages $5.8 Billion Army Task Order February 27, 2013 - 12:00pm Addthis James Hawkins James Hawkins BAGRAM AIRFIELD, Afghanistan - EM employee James Hawkins is currently serving the U.S. military in Afghanistan, where he is administering a $5.8 billion task order for the Army. A major in the U.S. Air Force Reserves, Hawkins is an administrative contracting officer for the Defense Contract Management Agency, a component of the Defense Department that directly contributes to the military readiness of the U.S. and its allies. Hawkins is an acquisition planning manager and procurement analyst in the Office of Procurement Planning in EM's Office of Acquisition and Project

194

Four Minority Serving Institutions Selected to Compete in the 2013 Solar  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Four Minority Serving Institutions Selected to Compete in the 2013 Four Minority Serving Institutions Selected to Compete in the 2013 Solar Decathlon Four Minority Serving Institutions Selected to Compete in the 2013 Solar Decathlon January 27, 2012 - 3:38pm Addthis An aerial shot of Orange County Great Park, site of the 2013 Solar Decathlon. An aerial shot of Orange County Great Park, site of the 2013 Solar Decathlon. Of the elite twenty teams that have been selected from across the country and around the world to compete in the 2013 Solar Decathlon, four are Minority Serving Institutions (MSIs), showcasing the talent of our nation's MSIs in science, technology, engineering, and mathematics. Congratulations are in order to these MSIs - and their partners - for making it to the Solar Decathlon: The University of Texas at El Paso and El Paso Community College (El

195

Return of the RedwoodGrillE All sandwiches served with lettuce, tomato, red onion and  

E-Print Network (OSTI)

.. . . . . . . . . . . . . . . . . . . . .$3.29 Organic spring mix garnished with carrot, red onion, tomato and cucumber with choice. . . . . . . . . . . . . . . . . . . . . . . . . . $5.69 Choose your flavor; served over white rice and garnished with bok choy, carrot, cabbage, red

California at Santa Cruz, University of

196

Chemical & Engineering News Serving the chemical, life sciences and laboratory worlds  

E-Print Network (OSTI)

Chemical & Engineering News Serving the chemical, life sciences and laboratory worlds Science the hydroxyl oxygen and alcoholic hydrogen stabilizes the transition state. Chemical & Engineering News ISSN 0009-2347 Copyright © 2010 American Chemical Society #12;

Truhlar, Donald G

197

Load Capacity of Bodies  

E-Print Network (OSTI)

For the stress analysis in a plastic body $\\Omega$, we prove that there exists a maximal positive number $C$, the \\emph{load capacity ratio,} such that the body will not collapse under any external traction field $t$ bounded by $Y_{0}C$, where $Y_0$ is the elastic limit. The load capacity ratio depends only on the geometry of the body and is given by $$ \\frac{1}{C}=\\sup_{w\\in LD(\\Omega)_D} \\frac{\\int_{\\partial\\Omega}|w|dA} {\\int_{\\Omega}|\\epsilon(w)|dV}=\\left\\|\\gamma_D\\right\\|. $$ Here, $LD(\\Omega)_D$ is the space of isochoric vector fields $w$ for which the corresponding stretchings $\\epsilon(w)$ are assumed to be integrable and $\\gamma_D$ is the trace mapping assigning the boundary value $\\gamma_D(w)$ to any $w\\in LD(\\Omega)_D$.

Reuven Segev

2005-11-01T23:59:59.000Z

198

Improved load ratio method for predicting crack length  

SciTech Connect

The elastic compliance from unloading/reloading sequences in a load-displacement record estimates well crack length in elastic-plastic fracture toughness tests of compact tension [C(T)] and bending type specimens. The need for partial unloading of the specimen makes it difficult to run the test under static loading and impossible under either dynamic loading or very high temperatures. Furthermore, fracture toughness testing in which crack length is determined from elastic compliance requires high precision testing equipment and highly skilled technicians. As a result, such tests are confined usually to research laboratories and seldom used under production settings. To eliminate these problems, an improved load ratio method of predicting crack length is proposed that utilizes only the recorded load versus load-line displacement curve (or load versus crack-mouth-opening displacement curve) without unloading/reloading sequences. As a result, the instrumentation is much simpler than in the elastic compliance or potential drop methods. If only a monotonic load-displacement record is to be measured the fracture toughness test becomes almost as simple to perform as a tension test. The method described here improves in three ways the ``original load ratio method`` proposed by Hu et al. First, a blunting term is added to the crack length before maximum load. Second, a strain hardening correction is included after maximum load. And, third, the initial crack length and the physical (final) crack length measured at the end of the test serve to anchor the predicted crack lengths, forcing agreement between predicted and measured values. The method predicts crack extension with excellent accuracy in specimens fabricated from A302, A508, and A533B piping and pressure vessel steels, A588 and A572 structural steels, and HY-80 ship steel.

Chen, X.; Albrecht, P. [Univ. of Maryland, College Park, MD (United States). Inst. for Systems Research; Wright, W. [Federal Highway Administration, McLean, VA (United States). Turner-Fairbank Highway Research Center; Joyce, J.A. [Naval Academy, Annapolis, MD (United States). Mechanical Engineering Dept.

1995-04-01T23:59:59.000Z

199

Load responsive hydrodynamic bearing  

Science Conference Proceedings (OSTI)

A load responsive hydrodynamic bearing is provided in the form of a thrust bearing or journal bearing for supporting, guiding and lubricating a relatively rotatable member to minimize wear thereof responsive to relative rotation under severe load. In the space between spaced relatively rotatable members and in the presence of a liquid or grease lubricant, one or more continuous ring shaped integral generally circular bearing bodies each define at least one dynamic surface and a plurality of support regions. Each of the support regions defines a static surface which is oriented in generally opposed relation with the dynamic surface for contact with one of the relatively rotatable members. A plurality of flexing regions are defined by the generally circular body of the bearing and are integral with and located between adjacent support regions. Each of the flexing regions has a first beam-like element being connected by an integral flexible hinge with one of the support regions and a second beam-like element having an integral flexible hinge connection with an adjacent support region. A least one local weakening geometry of the flexing region is located intermediate the first and second beam-like elements. In response to application of load from one of the relatively rotatable elements to the bearing, the beam-like elements and the local weakening geometry become flexed, causing the dynamic surface to deform and establish a hydrodynamic geometry for wedging lubricant into the dynamic interface.

Kalsi, Manmohan S. (Houston, TX); Somogyi, Dezso (Sugar Land, TX); Dietle, Lannie L. (Stafford, TX)

2002-01-01T23:59:59.000Z

200

MEMORANDUM FOR DISTRIBUTION FROM: DEAN G. SUBJECT: Business Process Change for Inter-Entity Transactions  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

6, 2004 6, 2004 MEMORANDUM FOR DISTRIBUTION FROM: DEAN G. SUBJECT: Business Process Change for Inter-Entity Transactions The i~i~ple~iientation of Oracle Public Sector Financials software as the Department's new core fi~iaiicial systeni on October 1 , 2004, will require a business process change in the way the Department finances and accouiits for work performed by one DOE office or integrated contractor for another. The purpose of this memorandum is to notify you of thc changes required and to ask for your feedback on the proposed approach. Our currcnt policy on accounting for transfers is set forth in the DOE Accounting Handbook, Chapter 12, "Transfers." On the basis of input from the I-MANAGEISTARS Project Team, my office has revised Chapter 12 to describe how work performed by one

Note: This page contains sample records for the topic "load serving entity" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

An Overview of the Lawrence Berkeley Laboratory Extended Entity-Relationship Database Tools  

E-Print Network (OSTI)

In this overview we briefly describe a collection of tools developed at Lawrence Berkeley Laboratory (LBL) for aiding users in specifying database structures and in querying databases using object-oriented concepts on top of commercial relational database management systems. These tools are based on an Extended Entity-Relationship (EER) model and allow users to deal with concise EER structures and queries rather than relational database definitions and queries which are usually large, hard to maintain, and involve terms that obscure the semantics of the application. Using the LBL/EER database tools users are insulated from the underlying database management system, and thus can avoid learning database management specific concepts and query languages. 1 Introduction Database applications involve large amounts of data that must be maintained and made available to users for analysis and manipulation. Database management systems (DBMSs) provide the capabilities required for stor...

Victor M. Markowitz; Arie Shoshani

1993-01-01T23:59:59.000Z

202

FDA Construction Project Serves as a Super ESPC Model | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

FDA Construction Project Serves as a Super ESPC Model FDA Construction Project Serves as a Super ESPC Model FDA Construction Project Serves as a Super ESPC Model October 7, 2013 - 1:55pm Addthis The U.S. Food and Drug Administration (FDA) has initiated an $890 million energy-saving construction project at the site of its new headquarters-a 1940s-era Navy base in White Oak, Maryland. Using a wide range of energy efficiency measures and solar energy, it has led to one of the largest Super Energy Savings Performance Contracts (ESPC). Watch the video modules below to learn more about this successful Super ESPC project. And find out how you can apply the FDA's energy management performance model to your federal agency's construction or building renovation project. Related Links Learn more about the energy-efficient and renewable energy technologies

203

Lawrence Livermore, Intel, Cray produce big data machine to serve as  

NLE Websites -- All DOE Office Websites (Extended Search)

1 1 For immediate release: 11/04/2013 | NR-13-11-01 High Resolution Image Catalyst is a unique high performance computing (HPC) cluster that will serve research scientists and provide a proving ground for new HPC and Big Data technologies and architectures. It was recently installed at Lawrence Livermore National Laboratory. Lawrence Livermore, Intel, Cray produce big data machine to serve as catalyst for next-generation HPC clusters Donald B Johnston, LLNL, (925) 423-4902, johnston19@llnl.gov Lawrence Livermore National Laboratory in partnership with Intel and Cray, today announced a unique high performance computing (HPC) cluster that will serve research scientists at all three institutions and provide a proving ground for new HPC and Big Data technologies and architectures.

204

Family-Owned Restaurant Serves Up Huge Energy Savings | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Family-Owned Restaurant Serves Up Huge Energy Savings Family-Owned Restaurant Serves Up Huge Energy Savings Family-Owned Restaurant Serves Up Huge Energy Savings May 8, 2013 - 2:27pm Addthis Energy efficiency upgrades helped the Athenian Corner reduce its operating costs and improved the restaurant's bottom line. | Photo courtesy of BetterBuildings Lowell Energy Upgrade program. Energy efficiency upgrades helped the Athenian Corner reduce its operating costs and improved the restaurant's bottom line. | Photo courtesy of BetterBuildings Lowell Energy Upgrade program. Rebecca Matulka Rebecca Matulka Digital Communications Specialist, Office of Public Affairs What are the key facts? The Athenian Corner, a family-owned restaurant in Lowell, Massachusetts, made energy efficiency upgrades that are saving it more than

205

Central Illinois Pub Serv Co (Illinois) EIA Revenue and Sales - February  

Open Energy Info (EERE)

source source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit History Facebook icon Twitter icon » Central Illinois Pub Serv Co (Illinois) EIA Revenue and Sales - February 2008 Jump to: navigation, search EIA Monthly Electric Utility Sales and Revenue Data for Central Illinois Pub Serv Co for February 2008. Monthly Electric Utility Sales and Revenue Data Short Name 2008-02 Utility Company Central Illinois Pub Serv Co (Illinois) Place Illinois Start Date 2008-02-01 End Date 2008-03-01 Residential Revenue(Thousand $) 32207 Residential Sales (MWh) 371971 Residential Consumers 331256 Commercial Revenue(Thousand $) 18469 Commercial Sales (MWh) 200148 Commercial Consumers 52121

206

Central Illinois Pub Serv Co (Illinois) EIA Revenue and Sales - November  

Open Energy Info (EERE)

source source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit History Facebook icon Twitter icon » Central Illinois Pub Serv Co (Illinois) EIA Revenue and Sales - November 2008 Jump to: navigation, search EIA Monthly Electric Utility Sales and Revenue Data for Central Illinois Pub Serv Co for November 2008. Monthly Electric Utility Sales and Revenue Data Short Name 2008-11 Utility Company Central Illinois Pub Serv Co (Illinois) Place Illinois Start Date 2008-11-01 End Date 2008-12-01 Residential Revenue(Thousand $) 36996 Residential Sales (MWh) 319196 Residential Consumers 331439 Commercial Revenue(Thousand $) 20266 Commercial Sales (MWh) 191904 Commercial Consumers 48563

207

Central Illinois Pub Serv Co (Illinois) EIA Revenue and Sales - September  

Open Energy Info (EERE)

source source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit History Facebook icon Twitter icon » Central Illinois Pub Serv Co (Illinois) EIA Revenue and Sales - September 2008 Jump to: navigation, search EIA Monthly Electric Utility Sales and Revenue Data for Central Illinois Pub Serv Co for September 2008. Monthly Electric Utility Sales and Revenue Data Short Name 2008-09 Utility Company Central Illinois Pub Serv Co (Illinois) Place Illinois Start Date 2008-09-01 End Date 2008-10-01 Residential Revenue(Thousand $) 21156 Residential Sales (MWh) 187445 Residential Consumers 329283 Commercial Revenue(Thousand $) 14874 Commercial Sales (MWh) 128656 Commercial Consumers 48190

208

Variable loading roller  

DOE Patents (OSTI)

An automatic loading roller for transmitting torque in traction drive devices in manipulator arm joints includes a two-part camming device having a first cam portion rotatable in place on a shaft by an input torque and a second cam portion coaxially rotatable and translatable having a rotating drive surface thereon for engaging the driven surface of an output roller with a resultant force proportional to the torque transmitted. Complementary helical grooves in the respective cam portions interconnected through ball bearings interacting with those grooves effect the rotation and translation of the second cam portion in response to rotation of the first. 14 figs.

Williams, D.M.

1988-01-21T23:59:59.000Z

209

Copyright 2009, The Ohio State University Selecting, Storing, and Serving Ohio Strawberries--page 1  

E-Print Network (OSTI)

in the refrigerator immediately. Just before serving, wash them in gently flowing· coldwaterinacolander to the many variables, such as moisture con- tent, size, and variety, it is impossible to give specific temperature for 24 hours or until jam has set. Store uncooked jams in refrigerator or freezer. They can

210

Integrating Renewable Energy Contracts and Wholesale Dynamic Pricing to Serve Aggregate  

E-Print Network (OSTI)

1 Integrating Renewable Energy Contracts and Wholesale Dynamic Pricing to Serve Aggregate Flexible batteries, with renewable energy resources. We formulate a stochastic optimal control problem that describes and the degree to which the aggregator can respond to dynamic pricing. Index Terms--Dynamic pricing, renewable

Oren, Shmuel S.

211

I. Bread, cereal, rice, and pasta 6-11 servings (aim for 50% whole grain)  

E-Print Network (OSTI)

Cranberry juice Dinner leftovers such as Chicken and veggie stir-fry over Steamed brown rice Low fat yogurt, and cheese (2-3 servings) IV. Fats, oils, and sweets (sparingly) Breakfast Ideas Oatmeal Raisins or dried cranberries Low-fat milk Low-fat mozzarella cheese sticks Whole-grain crackers Mixed dried fruits Low-fat

de la Torre, José R.

212

MTS Table Top Load frame  

NLE Websites -- All DOE Office Websites (Extended Search)

MTS Table Top Load frame MTS Table Top Load frame The Non-destructive Evaluation group operates an MTS Table Top Load frame for ultimate strength and life cycle testing of various ceramic, ceramic-matrix (FGI), carbon, carbon fiber, cermet (CMC) and metal alloy engineering samples. The load frame is a servo-hydraulic type designed to function in a closed loop configuration under computer control. The system can perform non-cyclic, tension, compression and flexure testing and cyclic fatigue tests. The system is comprised of two parts: * The Load Frame and * The Control System. Load Frame The Load Frame (figure 1) is a cross-head assembly which includes a single moving grip, a stationary grip and LVDT position sensor. It can generate up to 25 kN (5.5 kip) of force in the sample under test and can

213

Towards a syntactic signature for domain models: proposed descriptive metrics for visualizing the entity fan-out frequency distribution  

Science Conference Proceedings (OSTI)

The main objective of this paper is to find a minimal set of measures that allow the immediate, intuitive characterisation and visualization of the syntactic structure of models covering a particular application domain. The measures are validated ... Keywords: case measures, enterprise models, entity fan-out distribution, metrics, model analysis, model complexity, modelling

Jean-Paul van Belle

2002-09-01T23:59:59.000Z

214

Low-cost load research for electric utilities  

Science Conference Proceedings (OSTI)

Golden Valley Electric Association (GVEA) developed two pragmatic approaches to meet most load-research objectives at a substantially lower cost than would be incurred with traditional techniques. GVEA serves three customer classes, with most of its load in the Fairbanks area. GVEA's new approaches simulate load curves for individual customer classes to the degree necessary to meet most load-research objectives for the utility, including applications to cost-of-service analysis, rate design, demand-side management, and load forecasting. These approaches make class load-shape information available to utilities that cannot otherwise afford to develop such data. Although the two approaches were developed for a small utility, they are likely to work at least as well for medium and large utilities. The first approach simulates class curves by combining load data from system feeders with information on customer mix and energy usage. GVEA's supervisory control and data acquisition system gives hourly data on feeder loads, and its billing database provides the number of customers and kilowatt-hour usage by customer class on each feeder. The second approach enhances load-research results by redefining target parameters. Data from several like-hours are used to calculate substitutes for the parameters traditionally defined from single-hour data points. The precision of peak responsibility estimates, for example, can be improved if several of the highest hourly demands in a given time period are used rather than the single highest hourly demand. Arguably, use of several highest hourly demands can also improve the reliability of the allocation of responsibility.

Gray, D.A.; Butcher, M.

1994-08-01T23:59:59.000Z

215

Comparison of Wind Power and Load Forecasting Error Distributions: Preprint  

DOE Green Energy (OSTI)

The introduction of large amounts of variable and uncertain power sources, such as wind power, into the electricity grid presents a number of challenges for system operations. One issue involves the uncertainty associated with scheduling power that wind will supply in future timeframes. However, this is not an entirely new challenge; load is also variable and uncertain, and is strongly influenced by weather patterns. In this work we make a comparison between the day-ahead forecasting errors encountered in wind power forecasting and load forecasting. The study examines the distribution of errors from operational forecasting systems in two different Independent System Operator (ISO) regions for both wind power and load forecasts at the day-ahead timeframe. The day-ahead timescale is critical in power system operations because it serves the unit commitment function for slow-starting conventional generators.

Hodge, B. M.; Florita, A.; Orwig, K.; Lew, D.; Milligan, M.

2012-07-01T23:59:59.000Z

216

Energy Efficiency Indicators for High Electric-Load Buildings  

NLE Websites -- All DOE Office Websites (Extended Search)

Energy Efficiency Indicators for High Electric-Load Buildings Energy Efficiency Indicators for High Electric-Load Buildings Speaker(s): Bernard Aebischer Date: February 6, 2003 - 12:00pm Location: Bldg. 90 Seminar Host/Point of Contact: Kristina LaCommare Energy per unit of floor area is not an adequate indictor for energy efficiency in high electric-load buildings. For two activities, restaurants and computer centres, alternative indicators for energy efficiency are discussed. Prerequisites in order to be able to use these indicators in energy efficiency programmes are discussed. The opportunity of an internationally coordinated research activity is also presented. Since 1999, Dr. Bernard Aebischer has served as a senior scientist at CEPE (Centre for Energy Policy and Economics) of the Swiss Federal Institutes of

217

Direct versus Facility Centric Load Control for Automated Demand Response  

SciTech Connect

Direct load control (DLC) refers to the scenario where third party entities outside the home or facility are responsible for deciding how and when specific customer loads will be controlled in response to Demand Response (DR) events on the electric grid. Examples of third parties responsible for performing DLC may be Utilities, Independent System Operators (ISO), Aggregators, or third party control companies. DLC can be contrasted with facility centric load control (FCLC) where the decisions for how loads are controlled are made entirely within the facility or enterprise control systems. In FCLC the facility owner has more freedom of choice in how to respond to DR events on the grid. Both approaches are in use today in automation of DR and both will continue to be used in future market segments including industrial, commercial and residential facilities. This paper will present a framework which can be used to differentiate between DLC and FCLC based upon where decisions are made on how specific loads are controlled in response to DR events. This differentiation is then used to compare and contrast the differences between DLC and FCLC to identify the impact each has on:(1)Utility/ISO and third party systems for managing demand response, (2)Facility systems for implementing load control, (3)Communications networks for interacting with the facility and (4)Facility operators and managers. Finally a survey of some of the existing DR related specifications and communications standards is given and their applicability to DLC or FCLC. In general FCLC adds more cost and responsibilities to the facilities whereas DLC represents higher costs and complexity for the Utility/ISO. This difference is primarily due to where the DR Logic is implemented and the consequences that creates. DLC may be more certain than FCLC because it is more predictable - however as more loads have the capability to respond to DR signals, people may prefer to have their own control of end-use loads and FCLC systems. Research is needed to understand the predictability of FCLC which is related to the perceived value of the DR from the facility manager or home owner's perspective.

Koch, Ed; Piette, Mary Ann

2009-11-06T23:59:59.000Z

218

A Hybrid Query Language for an Extended Entity-Relationship Model  

E-Print Network (OSTI)

We present the hybrid query language HQL/EER for an Extended Entity-Relationship model. As its main characteristic, this language allows a user to use both graphical and textual elements in the formulation of one and the same query. We demonstrate the lookand -feel of this query language by means of examples, and show how syntax and semantics of this language are formally defined using programmed graph rewriting systems. Although we present the language in the context of the EER model, the concept of hybrid languages is applicable in the context of other database models as well. We illustrate this claim by discussing a prototype implementation of a Hybrid Query Tool based on an object-oriented approach, namely the Object Modeling Technique (OMT). 1 Introduction The database research efforts of the past decade have provided us with a wide range of both database models and systems, allowing the user to perform complex manipulations on data structures of high modeling power. Th...

Marc Andries; Gregor Engels

1993-01-01T23:59:59.000Z

219

Effects of pulsed-power loads upon an electric power grid  

DOE Green Energy (OSTI)

Certain proposed particle-accelerator and laser experiments, and other devices related to fusion research, require multi-megawatt, repetitive power pulses, often at low (subsynchronous) frequency. While some power-delivery technologies call for a certain degree of buffering of the utility demand using capacitive, inductive, or inertial energy storage, considerations have also been made for serving such loads directly from the line. In either case, such pulsed loads represent non-traditional applications from the utility's perspective which, in certain cases, can have significant design and operational implications. This paper outlines an approach to the analysis of the effects of such loads upon the electric power grid using existing analysis techniques. The impacts studied include busvoltage flicker, transient and dynamic stability, and torsional excitation. The impact of a particular pulsed load is examined and illustrated for the power network serving the Los Alamos National Laboratory. 19 refs., 13 figs.

Smolleck, H.A.; Ranade, S.J.; Prasad, N.R. (New Mexico State Univ., Las Cruces, NM (USA). Dept. of Electrical and Computer Engineering); Velasco, R.O. (Los Alamos National Lab., NM (USA))

1990-01-01T23:59:59.000Z

220

Central Illinois Pub Serv Co (Illinois) EIA Revenue and Sales - March 2008  

Open Energy Info (EERE)

March 2008 March 2008 Jump to: navigation, search EIA Monthly Electric Utility Sales and Revenue Data for Central Illinois Pub Serv Co for March 2008. Monthly Electric Utility Sales and Revenue Data Short Name 2008-03 Utility Company Central Illinois Pub Serv Co (Illinois) Place Illinois Start Date 2008-03-01 End Date 2008-04-01 Residential Revenue(Thousand $) 25715 Residential Sales (MWh) 250621 Residential Consumers 337464 Commercial Revenue(Thousand $) 15187 Commercial Sales (MWh) 156079 Commercial Consumers 52810 Industrial Revenue (Thousand $) 1664 Industrial Sales (MWh) 17211 Industrial Consumers 529 Other Revenue (Thousand $) 106 Other Sales (MWh) 880 Other Consumers 1 Total Revenue (Thousand $) 42672 Total Sales (MWh) 424791 Total Consumers 390804 Source: Energy Information Administration. Form EIA-826 Database Monthly

Note: This page contains sample records for the topic "load serving entity" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Central Illinois Pub Serv Co (Illinois) EIA Revenue and Sales - May 2008 |  

Open Energy Info (EERE)

Central Illinois Central Illinois Pub Serv Co for May 2008. Monthly Electric Utility Sales and Revenue Data Short Name 2008-05 Utility Company Central Illinois Pub Serv Co (Illinois) Place Illinois Start Date 2008-05-01 End Date 2008-06-01 Residential Revenue(Thousand $) 24553 Residential Sales (MWh) 218454 Residential Consumers 337410 Commercial Revenue(Thousand $) 19095 Commercial Sales (MWh) 187996 Commercial Consumers 55845 Industrial Revenue (Thousand $) 1116 Industrial Sales (MWh) 34382 Industrial Consumers 519 Other Revenue (Thousand $) 52 Other Sales (MWh) 702 Other Consumers 1 Total Revenue (Thousand $) 44816 Total Sales (MWh) 441534 Total Consumers 393775 Source: Energy Information Administration. Form EIA-826 Database Monthly Electric Utility Sales and Revenue Data [1]

222

Central Illinois Pub Serv Co (Illinois) EIA Revenue and Sales - January  

Open Energy Info (EERE)

January January 2009 Jump to: navigation, search EIA Monthly Electric Utility Sales and Revenue Data for Central Illinois Pub Serv Co for January 2009. Monthly Electric Utility Sales and Revenue Data Short Name 2009-01 Utility Company Central Illinois Pub Serv Co (Illinois) Place Illinois Start Date 2009-01-01 End Date 2009-02-01 Residential Revenue(Thousand $) 38208 Residential Sales (MWh) 442616 Residential Consumers 329875 Commercial Revenue(Thousand $) 18652 Commercial Sales (MWh) 197785 Commercial Consumers 47346 Industrial Revenue (Thousand $) 1173 Industrial Sales (MWh) 16509 Industrial Consumers 453 Other Revenue (Thousand $) 100 Other Sales (MWh) 1537 Other Consumers 1 Total Revenue (Thousand $) 58133 Total Sales (MWh) 658447 Total Consumers 377675

223

Central Illinois Pub Serv Co (Illinois) EIA Revenue and Sales - April 2008  

Open Energy Info (EERE)

Central Illinois Central Illinois Pub Serv Co for April 2008. Monthly Electric Utility Sales and Revenue Data Short Name 2008-04 Utility Company Central Illinois Pub Serv Co (Illinois) Place Illinois Start Date 2008-04-01 End Date 2008-05-01 Residential Revenue(Thousand $) 24400 Residential Sales (MWh) 247343 Residential Consumers 331573 Commercial Revenue(Thousand $) 14383 Commercial Sales (MWh) 152042 Commercial Consumers 52280 Industrial Revenue (Thousand $) 1241 Industrial Sales (MWh) 13081 Industrial Consumers 524 Other Revenue (Thousand $) 92 Other Sales (MWh) 1113 Other Consumers 1 Total Revenue (Thousand $) 40116 Total Sales (MWh) 413579 Total Consumers 384378 Source: Energy Information Administration. Form EIA-826 Database Monthly Electric Utility Sales and Revenue Data [1]

224

Central Illinois Pub Serv Co (Illinois) EIA Revenue and Sales - December  

Open Energy Info (EERE)

Central Illinois Central Illinois Pub Serv Co for December 2008. Monthly Electric Utility Sales and Revenue Data Short Name 2008-12 Utility Company Central Illinois Pub Serv Co (Illinois) Place Illinois Start Date 2008-12-01 End Date 2009-01-01 Residential Revenue(Thousand $) 35185 Residential Sales (MWh) 410509 Residential Consumers 327240 Commercial Revenue(Thousand $) 19393 Commercial Sales (MWh) 208884 Commercial Consumers 48125 Industrial Revenue (Thousand $) 1172 Industrial Sales (MWh) 15357 Industrial Consumers 466 Other Revenue (Thousand $) 78 Other Sales (MWh) 1202 Other Consumers 1 Total Revenue (Thousand $) 55828 Total Sales (MWh) 635952 Total Consumers 375832 Source: Energy Information Administration. Form EIA-826 Database Monthly Electric Utility Sales and Revenue Data [1]

225

Central Illinois Pub Serv Co (Illinois) EIA Revenue and Sales - June 2008 |  

Open Energy Info (EERE)

June 2008 June 2008 Jump to: navigation, search EIA Monthly Electric Utility Sales and Revenue Data for Central Illinois Pub Serv Co for June 2008. Monthly Electric Utility Sales and Revenue Data Short Name 2008-06 Utility Company Central Illinois Pub Serv Co (Illinois) Place Illinois Start Date 2008-06-01 End Date 2008-07-01 Residential Revenue(Thousand $) 39796 Residential Sales (MWh) 376563 Residential Consumers 348410 Commercial Revenue(Thousand $) 25354 Commercial Sales (MWh) 244206 Commercial Consumers 62285 Industrial Revenue (Thousand $) 1913 Industrial Sales (MWh) 11642 Industrial Consumers 542 Other Revenue (Thousand $) 54 Other Sales (MWh) 697 Other Consumers 1 Total Revenue (Thousand $) 67117 Total Sales (MWh) 633108 Total Consumers 411238 Source: Energy Information Administration. Form EIA-826 Database Monthly

226

Central Illinois Pub Serv Co (Illinois) EIA Revenue and Sales - February  

Open Energy Info (EERE)

February February 2009 Jump to: navigation, search EIA Monthly Electric Utility Sales and Revenue Data for Central Illinois Pub Serv Co for February 2009. Monthly Electric Utility Sales and Revenue Data Short Name 2009-02 Utility Company Central Illinois Pub Serv Co (Illinois) Place Illinois Start Date 2009-02-01 End Date 2009-03-01 Residential Revenue(Thousand $) 28078 Residential Sales (MWh) 297866 Residential Consumers 341636 Commercial Revenue(Thousand $) 15755 Commercial Sales (MWh) 165037 Commercial Consumers 49052 Industrial Revenue (Thousand $) 639 Industrial Sales (MWh) 16720 Industrial Consumers 474 Other Revenue (Thousand $) 128 Other Sales (MWh) 2187 Other Consumers 1 Total Revenue (Thousand $) 44600 Total Sales (MWh) 481810 Total Consumers 391163

227

Central Illinois Pub Serv Co (Illinois) EIA Revenue and Sales - January  

Open Energy Info (EERE)

January January 2008 Jump to: navigation, search EIA Monthly Electric Utility Sales and Revenue Data for Central Illinois Pub Serv Co for January 2008. Monthly Electric Utility Sales and Revenue Data Short Name 2008-01 Utility Company Central Illinois Pub Serv Co (Illinois) Place Illinois Start Date 2008-01-01 End Date 2008-02-01 Residential Revenue(Thousand $) 38361 Residential Sales (MWh) 457391 Residential Consumers 334784 Commercial Revenue(Thousand $) 20964 Commercial Sales (MWh) 244215 Commercial Consumers 52783 Industrial Revenue (Thousand $) 1321 Industrial Sales (MWh) 21368 Industrial Consumers 539 Other Revenue (Thousand $) 52 Other Sales (MWh) 707 Other Consumers 1 Total Revenue (Thousand $) 60698 Total Sales (MWh) 723681 Total Consumers 388107

228

Central Illinois Pub Serv Co (Illinois) EIA Revenue and Sales - October  

Open Energy Info (EERE)

Central Illinois Central Illinois Pub Serv Co for October 2008. Monthly Electric Utility Sales and Revenue Data Short Name 2008-10 Utility Company Central Illinois Pub Serv Co (Illinois) Place Illinois Start Date 2008-10-01 End Date 2008-11-01 Residential Revenue(Thousand $) 27599 Residential Sales (MWh) 248769 Residential Consumers 329654 Commercial Revenue(Thousand $) 19506 Commercial Sales (MWh) 193998 Commercial Consumers 48492 Industrial Revenue (Thousand $) 1811 Industrial Sales (MWh) 14741 Industrial Consumers 477 Other Revenue (Thousand $) 55 Other Sales (MWh) 713 Other Consumers 1 Total Revenue (Thousand $) 48971 Total Sales (MWh) 458221 Total Consumers 378624 Source: Energy Information Administration. Form EIA-826 Database Monthly Electric Utility Sales and Revenue Data [1]

229

Monitoring-based temporal prediction of power entities in smart grid cities  

Science Conference Proceedings (OSTI)

This paper develops prediction models for groundwater and wind speed in smart grid cities, where the gradual penetration of electric vehicles keeps increasing load in its power system. As a major consumption source and a renewable energy source, water ... Keywords: artificial neural network, electric vehicle, groundwater, smart grid city, wind power

Junghoon Lee; Seong Baeg Kim; Gyung-Leen Park; Chan Jung Park

2012-10-01T23:59:59.000Z

230

Load Management: Opportunity or Calamity?  

E-Print Network (OSTI)

After the change in the economics of generating electricity which took place in 1973, many utilities are examining options to hold down their costs. One fact which is clear is that the difference between peak and off peak generating costs is much larger now than prior to 1973. Utilities are examining two options which can be termed load management. One option is to control discretionary loads during peak periods. Cycling of residential water heaters or shutting off industrial electric furnaces during peak periods are both examples of load control which lower the costs borne by the utility. The other option is the use of seasonal surcharges or time-of-day rates to induce customers to alter their usage patterns. Both these load management options focus on reducing utility costs overall without regard to the cost to the consumers affected by the load management options. The issue, then, is whether industrial customers can find opportunities to lower their costs under load management.

Males, R.; Hassig, N.

1981-01-01T23:59:59.000Z

231

Dynamic load balancing of applications  

DOE Patents (OSTI)

An application-level method for dynamically maintaining global load balance on a parallel computer, particularly on massively parallel MIMD computers. Global load balancing is achieved by overlapping neighborhoods of processors, where each neighborhood performs local load balancing. The method supports a large class of finite element and finite difference based applications and provides an automatic element management system to which applications are easily integrated.

Wheat, Stephen R. (Albuquerque, NM)

1997-01-01T23:59:59.000Z

232

Dynamic load balancing of applications  

DOE Patents (OSTI)

An application-level method for dynamically maintaining global load balance on a parallel computer, particularly on massively parallel MIMD computers is disclosed. Global load balancing is achieved by overlapping neighborhoods of processors, where each neighborhood performs local load balancing. The method supports a large class of finite element and finite difference based applications and provides an automatic element management system to which applications are easily integrated. 13 figs.

Wheat, S.R.

1997-05-13T23:59:59.000Z

233

Unbundling the retail gas market: Current activities and guidance for serving residential and small customers  

Science Conference Proceedings (OSTI)

The restructuring of retail gas services has followed a typical pattern for previously heavily regulated industries: large customers are initially given rights to purchase unbundled services from different entities, with the same rights dispersed over time to smaller customers. For about ten years now industrial customers in most states have been able to {open_quotes}play the market{close_quotes}. Since the passage of the Federal Energy Regulatory Commission (FERC) Order 636 in 1992, interest has centered on expanding service unbundling to small retail customers, including residential customers. Importantly, the Order prohibited pipelines from providing bundled sales service. This is not surprising - in the telecommunications industry, for example, the unbundling of wholesale services was a strong stimulant for developing competition in the local exchange market. The push for small-customer service unbundling has derived from the basic but politically attractive idea that all retail customers should directly benefit from competitive forces in the natural gas industry. When one looks at the movement of prices since 1985, it is easy to see that large retail customers have enjoyed more favorable prices than other retail customers. For example, over the period 1985 to 1994 gas prices to industrial customers and electric utilities fell around 23 percent and 36 percent, respectively. In comparison, gas prices to residential customers increased by around 5 percent while gas prices to commercial customers decreased slightly by about 1 percent. This report examines various aspects of unbundling to small retail gas customers, with special emphasis on residential customers.

Costello, K.W.; Lemon, J.R.

1996-05-01T23:59:59.000Z

234

Alaska Village Electric Load Calculator  

DOE Green Energy (OSTI)

As part of designing a village electric power system, the present and future electric loads must be defined, including both seasonal and daily usage patterns. However, in many cases, detailed electric load information is not readily available. NREL developed the Alaska Village Electric Load Calculator to help estimate the electricity requirements in a village given basic information about the types of facilities located within the community. The purpose of this report is to explain how the load calculator was developed and to provide instructions on its use so that organizations can then use this model to calculate expected electrical energy usage.

Devine, M.; Baring-Gould, E. I.

2004-10-01T23:59:59.000Z

235

High-Power Rf Load  

DOE Patents (OSTI)

A compact high-power RF load comprises a series of very low Q resonators, or chokes [16], in a circular waveguide [10]. The sequence of chokes absorb the RF power gradually in a short distance while keeping the bandwidth relatively wide. A polarizer [12] at the input end of the load is provided to convert incoming TE.sub.10 mode signals to circularly polarized TE.sub.11 mode signals. Because the load operates in the circularly polarized mode, the energy is uniformly and efficiently absorbed and the load is more compact than a rectangular load. Using these techniques, a load having a bandwidth of 500 MHz can be produced with an average power dissipation level of 1.5 kW at X-band, and a peak power dissipation of 100 MW. The load can be made from common lossy materials, such as stainless steel, and is less than 15 cm in length. These techniques can also produce loads for use as an alternative to ordinary waveguide loads in small and medium RF accelerators, in radar systems, and in other microwave applications. The design is easily scalable to other RF frequencies and adaptable to the use of other lossy materials.

Tantawi, Sami G. (San Mateo, CA); Vlieks, Arnold E. (Livermore, CA)

1998-09-01T23:59:59.000Z

236

Static identification of delinquent loads  

E-Print Network (OSTI)

The effective use of processor caches is crucial to the performance of applications. It has been shown that cache misses are not evenly distributed throughout a program. In applications running on RISC-style processors, a small number of delinquent load instructions are responsible for most of the cache misses. Identification of delinquent loads is the key to the success of many cache optimization and prefetching techniques. In this paper, we propose a method for identifying delinquent loads that can be implemented at compile time. Our experiments over eighteen benchmarks from the SPEC suite shows that our proposed scheme is stable across benchmarks, inputs, and cache structures, identifying an average of 10 % of the total number of loads in the benchmarks we tested that account for over 90 % of all data cache misses. As far as we know, this is the first time a technique for static delinquent load identification with such a level of precision and coverage has been reported. While comparable techniques can also identify load instructions that cover 90 % of all data cache misses, they do so by selecting over 50 % of all load instructions in the code, resulting in a high number of false positives. If basic block profiling is used in conjunction with our heuristic, then our results show that it is possible to pin down just 1.3 % of the load instructions that account for 82 % of all data cache misses. 1.

Vlad-mihai Panait; Amit Sasturkar Ý

2004-01-01T23:59:59.000Z

237

LOAD FORECASTING Eugene A. Feinberg  

E-Print Network (OSTI)

's electricity price forecasting model, produces forecast of gas demand consistent with electric load. #12Gas demand Council's Market Price of Electricity Forecast Natural GasDemand Electric Load Aggregating Natural between the natural gas and electricity and new uses of natural gas emerge. T natural gas forecasts

Feinberg, Eugene A.

238

1998 Pacific Northwest Loads and Resources Study: The White Book.  

DOE Green Energy (OSTI)

The Pacific Northwest Loads and Resources Study (White Book) is published annually by BPA and establishes the planning basis for supplying electricity to customers. It serves a dual purpose. First, the White Book presents projections of regional and Federal system load and resource capabilities, along with relevant definitions and explanations. Second, the White Book serves as a benchmark for annual BPA determinations made pursuant to the 1981 regional power sales contracts. Specifically, BPA uses the information in the White Book for determining the notice required when customers request to increase or decrease the amount of power purchased from BPA. The White Book compiles information obtained from several formalized resource planning reports and data submittals, including those from the Northwest Power Planning Council (Council) and the Pacific Northwest Utilities Conference Committee (PNUCC). The White Book is not an operational planning guide, nor is it used for inventory planning to determine BPA revenues. Operation of the Federal Columbia River Power System (FCRPS) is based on a set of criteria different from that used for resource planning decisions. Operational planning is dependent upon real-time or near-term knowledge of system conditions, including expectations of river flows and runoff, market opportunities, availability of reservoir storage, energy exchanges, and other factors affecting the dynamics of operating a power system. The 1998 White Book is presented in two documents: (1) this summary of Federal system and Pacific Northwest region loads and resources; and (2) a technical appendix detailing the loads and resources for each major Pacific Northwest generating utility. This analysis updates the December 1997 Pacific Northwest Loads and Resources Study.

United States. Bonneville Power Administration.

1998-12-01T23:59:59.000Z

239

An Evaluation of the Water Heater Load Potential for Providing Regulation Service  

Science Conference Proceedings (OSTI)

This paper investigates the possibility of providing aggregated regulation services with small loads, such as water heaters or air conditioners. A direct-load control algorithm is presented to aggregate the water heater load for the purpose of regulation. A dual-element electric water heater model is developed, which accounts for both thermal dynamics and users’ water consumptions. A realistic regulation signal was used to evaluate the number of water heaters needed and the operational characteristics of a water heater when providing 2-MW regulation service. Modeling results suggest that approximately 33,333 water heaters are needed to provide a 2-MW regulation service 24 hours a day. However, if water heaters only provide regulation from 6:00 to 24:00, approximately 20,000 will be needed. Because the control algorithm has considered the thermal setting of the water heater, the customer comfort is obstructed little. Therefore, the aggregated regulation service provided by water heater loads can become a major source of revenue for load-service entities when the smart grid enables the direct load control.

Kondoh, Junji; Lu, Ning; Hammerstrom, Donald J.

2011-08-31T23:59:59.000Z

240

building load | OpenEI  

Open Energy Info (EERE)

load load Dataset Summary Description This dataset contains hourly load profile data for 16 commercial building types (based off the DOE commercial reference building models) and residential buildings (based off the Building America House Simulation Protocols). This dataset also includes the Residential Energy Consumption Survey (RECS) for statistical references of building types by location. Source Commercial and Residential Reference Building Models Date Released April 18th, 2013 (9 months ago) Date Updated July 02nd, 2013 (7 months ago) Keywords building building demand building load Commercial data demand Energy Consumption energy data hourly kWh load profiles Residential Data Quality Metrics Level of Review Some Review Comment Temporal and Spatial Coverage Frequency Annually

Note: This page contains sample records for the topic "load serving entity" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Wind load reduction for heliostats  

DOE Green Energy (OSTI)

This report presents the results of wind-tunnel tests supported through the Solar Energy Research Institute (SERI) by the Office of Solar Thermal Technology of the US Department of Energy as part of the SERI research effort on innovative concentrators. As gravity loads on drive mechanisms are reduced through stretched-membrane technology, the wind-load contribution of the required drive capacity increases in percentage. Reduction of wind loads can provide economy in support structure and heliostat drive. Wind-tunnel tests have been directed at finding methods to reduce wind loads on heliostats. The tests investigated primarily the mean forces, moments, and the possibility of measuring fluctuating forces in anticipation of reducing those forces. A significant increase in ability to predict heliostat wind loads and their reduction within a heliostat field was achieved.

Peterka, J.A.; Hosoya, N.; Bienkiewicz, B.; Cermak, J.E.

1986-05-01T23:59:59.000Z

242

load data | OpenEI Community  

Open Energy Info (EERE)

51 51 Varnish cache server Home Groups Community Central Green Button Applications Developer Utility Rate FRED: FRee Energy Database More Public Groups Private Groups Features Groups Blog posts Content Stream Documents Discussions Polls Q & A Events Notices My stuff Energy blogs 429 Throttled (bot load) Error 429 Throttled (bot load) Throttled (bot load) Guru Meditation: XID: 2142234851 Varnish cache server load data Home Sfomail's picture Submitted by Sfomail(48) Member 17 May, 2013 - 12:03 Commercial and Residential Hourly Load Data Now Available on OpenEI! building load building load data commercial load data dataset datasets electric load data load data load profile OpenEI residential load TMY3 United States Load data Image source: NREL Files: application/zip icon System Advisor Model Tool for Downloading Load Data

243

Spinning Reserve from Responsive Load  

SciTech Connect

As power system costs rise and capacity is strained demand response can provide a significant system reliability benefit at a potentially attractive cost. The 162 room Music Road Hotel in Pigeon Forge Tennessee agreed to host a spinning reserve test. The Tennessee Valley Authority (TVA) supplied real-time metering and monitoring expertise to record total hotel load during both normal operations and testing. Preliminary testing showed that hotel load can be curtailed by 22% to 37% depending on the outdoor temperature and the time of day. The load drop was very rapid, essentially as fast as the 2 second metering could detect.

Kueck, John D [ORNL; Kirby, Brendan J [ORNL; Laughner, T [Tennessee Valley Authority (TVA); Morris, K [Tennessee Valley Authority (TVA)

2009-01-01T23:59:59.000Z

244

Advanced nonintrusive load monitoring system  

E-Print Network (OSTI)

There is a need for flexible, inexpensive metering technologies that can be deployed in many different monitoring scenarios. Individual loads may be expected to compute information about their power consumption. Utility ...

Wichakool, Warit, 1977-

2011-01-01T23:59:59.000Z

245

OpenEI - building load  

Open Energy Info (EERE)

are given by a location defined by the Typical Meteorological Year (TMY) for which the weather data was collected. Commercial load data is sorted by the (TMY) site as a...

246

Permanent Load Shift Control Strategies  

NLE Websites -- All DOE Office Websites (Extended Search)

of Permanent Load Shifting for HVAC and other storage assets as it relates to summer on-peak demand, how it can be dynamically and autonomously controlled, and its relationship...

247

Building load control and optimization  

E-Print Network (OSTI)

Researchers and practitioners have proposed a variety of solutions to reduce electricity consumption and curtail peak demand. This research focuses on load control by improving the operations in existing building HVAC ...

Xing, Hai-Yun Helen, 1976-

2004-01-01T23:59:59.000Z

248

Random Deployment of Data Collectors for Serving Randomly-Located Sensors  

E-Print Network (OSTI)

Recently, wireless communication industries have begun to extend their services to machine-type communication devices as well as to the user equipment. Such machine-type communication devices as meters and sensors need intermittent uplink resources to report measured or sensed data to their serving data collector. It is however hard to dedicate limited uplink resources to each of them. Thus, efficient service of a tremendous number of devices with low activities may consider simple random access as a solution. The data collectors receiving the measured data from many sensors simultaneously can successfully decode only signals with signal-to-interference-plus-noise-ratio (SINR) above a certain value. The main design issues for this environment become how many data collectors are needed, how much power sensor nodes transmit with, and how wireless channels affect the performance. This paper provides answers to those questions through a stochastic analysis based on a spatial point process and on simulations.

Kwon, Taesoo

2011-01-01T23:59:59.000Z

249

Load transfer coupling regression curve fitting for distribution load forecasting  

SciTech Connect

The planning of distribution facilities requires forecasts of future substation and feeder loads. Extrapolation based on a curve fit to past annual peak loads is currently the most popular manner of accomplishing this forecast. Curve fitting suffers badly from data shifts caused by switching as loads are routinely moved from one substation to another during the course of utility operations. This switching contaminates the data, reducing forecast accuracy. A new regression application reduces error due to these transfers by over an order of magnitude. A key to the usefulness of this method is that the amount of the transfer, and its direction (whether it was to or from a substation), is not a required input. The new technique, aspects of computer implementation of it, and a series of tests showing its advantage over normal multiple regression methods are given.

Willis, H.L.; Powell, R.W.

1984-05-01T23:59:59.000Z

250

Realizing load reduction functions by aperiodic switching of load groups  

SciTech Connect

This paper investigates the problem of scheduling ON/OFF switching of residential appliances under the control of a Load Management System (LMS). The scheduling process is intended to reduce the controlled appliances` power demand in accordance with a predefined load reduction profile. To solve this problem, a solution approach, based on the methodology of Pulse Width Modulation (PWM), is introduced. This approach provides a flexible mathematical basis for studying different aspects of the scheduling problem. The conventional practices in this area are shown to be special cases of the PWM technique. By applying the PWM-based technique to the scheduling problem, important classes of scheduling errors are identified and analytical expressions describing them are derived. These expressions are shown to provide sufficient information to compensate for the errors. Detailed simulations of load groups` response to switching actions are use to support conclusions of this study.

Navid-Azarbaijani, N. [McGill Univ., Montreal, Quebec (Canada). Dept. of Electrical Engineering; Banakar, M.H. [CAE Electronics Ltd., St. Laurent, Quebec (Canada)

1996-05-01T23:59:59.000Z

251

Validation of a Building Simulation Tool Using Field Data for Three Identical Configuration Full-Serve Restaurants Using Different HVAC Systems  

E-Print Network (OSTI)

A new building application for a pre-existing HVAC software tool which calculates the benefits of desiccant-assisted HVAC equipment versus the performance of a standard vapor-compression system is used to model the monitored results, see Yborra and Spears (2000), for three full-service restaurants. A standard vapor-compression system, an enthalpy assisted vapor-compression system, and a desiccant-assisted vapor-compression system are compared. The vapor-compression portion of each system is comprised of three rooftop units, specifications for each may be found in Yborra and Spears, "Field- Evaluation of Alternative HVAC Strategies to Meet Ventilation, Comfort, and Humidity Control Criteria at Three Full-Serve Restaurants". The software tool uses DOE 2.1E as a calculation engine which runs in the background. Previously, the software tool could model two different hotel configurations, a quickserve restaurant, a supermarket, a retail store, an ice arena, a school, a movie theater, a nursing home and a hospital. With the larger eating area, the full-serve restaurant had the capacity for sensible or enthalpy heat recovery from the exhausted air in the sit-down area. Quick-Serve Restaurants (QSR's) were precluded from these energy saving devices as the exhausted air was heavily laden with grease. Still, even with the kitchen exhausts facing away from the rooftop unit (RTU) intakes, the enthalpy wheels showed noticeable loading from grease. As the field monitoring was performed near Philadelphia, PA, National Renewable Energy Laboratory (NREL) hour-by-hour bin TMY2 meteorological data was used for Philadelphia to model the annual outdoor conditions experienced by each site. Output was provided in the form of humidity bins, monthly energy usage and cost, as well as total annual gas and electric costs. As the fill-serve restaurants were located on the North-Eastem region of the United States, patron comfort was of greater importance to management than annual energy cost savings. Once the model results were determined to properly reflect those of the case studies, the different building equipment types were "moved" around the United States by choosing different bin weather data sets corresponding to Chicago, IL, Atlanta, GA, and Houston, TX. While the default energy rates available in the program are 4 years old, the economic results provide a sound cost comparison.

Brillhart, P. L.; Worek, W. M.

2000-01-01T23:59:59.000Z

252

FINAL PROJECT REPORT LOAD MODELING TRANSMISSION RESEARCH  

E-Print Network (OSTI)

PSLF that incorporates motor  A?C, ZIP, and electronic load the fractions motors A?C, ZIP, and electronic loads.    Usethat incorporates motor  A?C, ZIP, and  electronic load 

Lesieutre, Bernard

2013-01-01T23:59:59.000Z

253

load profile | OpenEI Community  

Open Energy Info (EERE)

load profile Home Sfomail's picture Submitted by Sfomail(48) Member 17 May, 2013 - 13:03 Commercial and Residential Hourly Load Data Now Available on OpenEI building load building...

254

Monthly Crustal Loading Corrections for Satellite Altimetry  

Science Conference Proceedings (OSTI)

Satellite altimeter measurements of sea surface height include a small contribution from vertical motion of the seafloor caused by crustal loading. Loading by ocean tides is routinely allowed for in altimeter data processing. Here, loading by ...

R. D. Ray; S. B. Luthcke; T. van Dam

2013-05-01T23:59:59.000Z

255

Annual Report of the Columbia River Treaty, Canadian and United States Entities: 1 October 1992--30 September 1993.  

DOE Green Energy (OSTI)

This annual Columbia River Treaty Entity Report is for the 1993 Water Year, 1 October 1992 through 30 September 1993. It includes information on the operation of Mica, Arrow, Duncan, and Libby reservoirs during that period with additional information covering the reservoir system operating year, 1 August 1992 through 31 July 1993. The power and flood control effects downstream in Canada and the United States are described. This report is the twenty-seventh of a series of annual reports covering the period since the ratification of the Columbia River Treaty in September 1964.

Columbia River Treaty Operating Committee; B.C. Hydro; United States. Bonneville Power Administration

1993-11-01T23:59:59.000Z

256

Peak load management: Potential options  

SciTech Connect

This report reviews options that may be alternatives to transmission construction (ATT) applicable both generally and at specific locations in the service area of the Bonneville Power Administration (BPA). Some of these options have potential as specific alternatives to the Shelton-Fairmount 230-kV Reinforcement Project, which is the focus of this study. A listing of 31 peak load management (PLM) options is included. Estimated costs and normalized hourly load shapes, corresponding to the respective base load and controlled load cases, are considered for 15 of the above options. A summary page is presented for each of these options, grouped with respect to its applicability in the residential, commercial, industrial, and agricultural sectors. The report contains comments on PLM measures for which load shape management characteristics are not yet available. These comments address the potential relevance of the options and the possible difficulty that may be encountered in characterizing their value should be of interest in this investigation. The report also identifies options that could improve the efficiency of the three customer utility distribution systems supplied by the Shelton-Fairmount Reinforcement Project. Potential cogeneration options in the Olympic Peninsula are also discussed. These discussions focus on the options that appear to be most promising on the Olympic Peninsula. Finally, a short list of options is recommended for investigation in the next phase of this study. 9 refs., 24 tabs.

Englin, J.E.; De Steese, J.G.; Schultz, R.W.; Kellogg, M.A.

1989-10-01T23:59:59.000Z

257

Building Energy Software Tools Directory: Load Express  

NLE Websites -- All DOE Office Websites (Extended Search)

graphical interface makes Load Express a powerful engineering tool with a very short learning curve. The "rookie" or experienced user can quickly and accurately perform load...

258

Self-aligning biaxial load frame  

DOE Patents (OSTI)

An self-aligning biaxial loading apparatus for use in testing the strength of specimens while maintaining a constant specimen centroid during the loading operation. The self-aligning biaxial loading apparatus consists of a load frame and two load assemblies for imparting two independent perpendicular forces upon a test specimen. The constant test specimen centroid is maintained by providing elements for linear motion of the load frame relative to a fixed cross head, and by alignment and linear motion elements of one load assembly relative to the load frame. 3 figures.

Ward, M.B.; Epstein, J.S.; Lloyd, W.R.

1994-01-18T23:59:59.000Z

259

Decentralized customerlevel under frequency load shedding in...  

Open Energy Info (EERE)

enables the management of large groups of distributed loads under a single innovative control schemes to use the flexibility of electrical loads for power system purposes....

260

Method for loading resin beds  

DOE Patents (OSTI)

An improved method of preparing nuclear reactor fuel by carbonizing a uranium loaded cation exchange resin provided by contacting a H.sup.+ loaded resin with a uranyl nitrate solution deficient in nitrate, comprises providing the nitrate deficient solution by a method comprising the steps of reacting in a reaction zone maintained between about 145.degree.-200.degree. C, a first aqueous component comprising a uranyl nitrate solution having a boiling point of at least 145.degree. C with a second aqueous component to provide a gaseous phase containing HNO.sub.3 and a reaction product comprising an aqueous uranyl nitrate solution deficient in nitrate.

Notz, Karl J. (Oak Ridge, TN); Rainey, Robert H. (Knoxville, TN); Greene, Charles W. (Knoxville, TN); Shockley, William E. (Oak Ridge, TN)

1978-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "load serving entity" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

PRB rail loadings shatter record  

Science Conference Proceedings (OSTI)

Rail transport of coal in the Powder River Basin has expanded, with a record 2,197 trains loaded in a month. Arch Coal's Thunder basin mining complex has expanded by literally bridging the joint line railway. The dry fork mine has also celebrated its safety achievements. 4 photos.

Buchsbaum, L.

2008-09-15T23:59:59.000Z

262

Automatic Electric Load Identification in  

E-Print Network (OSTI)

Abstract — A microgrid is the power system of choice for the electrification of rural areas in developing countries. It should be able to adapt to changing load situations without the need for specialists to change the configuration of the microgrid controller. This paper proposes a self-configuring microgrid management system that is able to adjust both generation and demand of the system, so that also in case of growing electricity demand the grid can still be operable by disconnecting unessential loads. A crucial task for the microgrid controller is to automatically identify the connected loads on the basis of their consumption behaviors. For this, a template-matching algorithm is proposed that is based on Dynamic Time Warping, which is primarily used in speech recognition. It has been found that for load profile analysis, simple signal features such as the number of rising edges or the aggregated energy consumption in a given time window is sufficient to describe the signal. In contrast to speech recognition, frequency domain analysis is not necessary.

Self-configuring Microgrids; Friederich Kupzog; Tehseen Zia; Adeel Abbas Zaidi

2009-01-01T23:59:59.000Z

263

On-line load relief control  

SciTech Connect

This paper describes the results of an investigation concerning the on-line prediction and enhancement of load relief. The effects of voltage fluctuation, system voltage profile control and generator voltage adjustment on load relief and load shedding operations during under-frequency transients are studied. The technique promoted in the paper may be used to reduce system spinning reserve or prospective load shedding.

Jovanovic, S.; Fox, B.; Thompson, J.G. (Queen' s Univ. of Belfast (United Kingdom))

1994-11-01T23:59:59.000Z

264

Load Forecasting for Modern Distribution Systems  

Science Conference Proceedings (OSTI)

Load forecasting is a fundamental activity for numerous organizations and activities within a utility, including planning, operations, and control. Transmission and Distribution (T&D) planning and design engineers use the load forecast to determine whether any changes and additions are needed to the electric system to satisfy the anticipated load. Other load forecast users include system operations, financial ...

2013-03-08T23:59:59.000Z

265

Load Forecast For use in Resource Adequacy  

E-Print Network (OSTI)

Load Forecast 2019 For use in Resource Adequacy Massoud Jourabchi #12;In today's presentation d l­ Load forecast methodology ­ Drivers of the forecast f i­ Treatment of conservation ­ Incorporating impact of weather ­ Forecast for 2019 #12;Regional Loads (MWA and MW)Regional Loads (MWA and MW

266

Evolving non-intrusive load monitoring  

Science Conference Proceedings (OSTI)

Non-intrusive load monitoring (NILM) identifies used appliances in a total power load according to their individual load characteristics. In this paper we propose an evolutionary optimization algorithm to identify appliances, which are modeled as on/off ... Keywords: NILM, evolution, evolutionary algorithm, knapsack problem, non-intrusive load monitoring

Dominik Egarter; Anita Sobe; Wilfried Elmenreich

2013-04-01T23:59:59.000Z

267

Characterizing Household Plug Loads through Self-Administered Load Research  

Science Conference Proceedings (OSTI)

Household miscellaneous loads, which include consumer electronics, are the fastest growing segment of household energy use in the United States. Although the relative energy intensity of applications such as heating and cooling is declining, the DOEAnnual Energy Outlook forecasts that the intensity of residential miscellaneous end uses will increase substantially by 2030. Studies by TIAX and Ecos Consulting reveal that miscellaneous devices8212smaller devices in terms of energy draw but growing in usage8...

2009-12-09T23:59:59.000Z

268

Load-shape development aids planning  

SciTech Connect

The concept that provides capable, load-shape development, is being adopted by several utilities and power pools. Public Service Electric and Gas Company has developed a computer simulation model that can predict a utility's load shape for up to a 30-year period. The objective of the PSE and G model, known as EICS (Electric Load-Curve Synthesis) is to provide a demand profile, to examine the impact of load mangement and other activities upon a system's load shape, and to apply appropriate forecast non-load-management and load-management impacts before finally examining the resulting revised load-shape. Other models dealing with load-shape are discussed. Specifically, the Systems Control Inc. model for EPRI (SCI/EPRI), useful in performing accurate simulations of various load-control strategies involving customer appliance control is mentioned.

Gellings, C.W.

1979-12-15T23:59:59.000Z

269

Remote Area Power Supply (RAPS) load and resource profiles.  

SciTech Connect

In 1997, an international team interested in the development of Remote Area Power Supply (RAPS) systems for rural electrification projects around the world was organized by the International Lead Zinc Research Organization (ILZRO) with the support of Sandia National Laboratories (SNL). The team focused on defining load and resource profiles for RAPS systems. They identified single family homes, small communities, and villages as candidates for RAPS applications, and defined several different size/power requirements for each. Based on renewable energy and resource data, the team devised a ''strawman'' series of load profiles. A RAPS system typically consists of a renewable and/or conventional generator, power conversion equipment, and a battery. The purpose of this report is to present data and information on insolation levels and load requirements for ''typical'' homes, small communities, and larger villages around the world in order to facilitate the development of robust design practices for RAPS systems, and especially for the storage battery component. These systems could have significant impact on areas of the world that would otherwise not be served by conventional electrical grids.

Giles, Lauren (Energetics, Inc., Washington, DC); Skolnik, Edward G. (Energetics, Inc., Washington, DC); Marchionini, Brian (Energetics, Inc., Washington, DC); Fall, Ndeye K. (Energetics, Inc., Washington, DC)

2007-07-01T23:59:59.000Z

270

Remote Area Power Supply (RAPS) load and resource profiles.  

SciTech Connect

In 1997, an international team interested in the development of Remote Area Power Supply (RAPS) systems for rural electrification projects around the world was organized by the International Lead Zinc Research Organization (ILZRO) with the support of Sandia National Laboratories (SNL). The team focused on defining load and resource profiles for RAPS systems. They identified single family homes, small communities, and villages as candidates for RAPS applications, and defined several different size/power requirements for each. Based on renewable energy and resource data, the team devised a ''strawman'' series of load profiles. A RAPS system typically consists of a renewable and/or conventional generator, power conversion equipment, and a battery. The purpose of this report is to present data and information on insolation levels and load requirements for ''typical'' homes, small communities, and larger villages around the world in order to facilitate the development of robust design practices for RAPS systems, and especially for the storage battery component. These systems could have significant impact on areas of the world that would otherwise not be served by conventional electrical grids.

Giles, Lauren (Energetics, Inc., Washington, DC); Skolnik, Edward G. (Energetics, Inc., Washington, DC); Marchionini, Brian (Energetics, Inc., Washington, DC); Fall, Ndeye K. (Energetics, Inc., Washington, DC)

2007-07-01T23:59:59.000Z

271

Load Scheduling with Profile Information  

E-Print Network (OSTI)

. Within the past five years, many manufactures have added hardware performance counters to their microprocessors to generate profile data cheaply. We show how to use Compaq's DCPI tool to determine load latencies which are at a fine, instruction granularity and use them as fodder for improving instruction scheduling. We validate our heuristic for using DCPI latency data to classify loads as hits and misses against simulation numbers. We map our classification into the Multiflow compiler's intermediate representation, and use a locality sensitive Balanced scheduling algorithm. Our experiments illustrate that our algorithm improves run times by 1% on average, but up to 10% on a Compaq Alpha. 1 Introduction This paper explores how to use hardware performance counters to produce fine grain latency information to improve compiler scheduling. We use this information to hide latencies with any available instruction level parallelism (ILP). (ILP for an instruction is the number of o...

Götz Lindenmaier; Kathryn S. McKinley; Olivier Temam

2000-01-01T23:59:59.000Z

272

AMENDED AND RESTATED DELEGATION AGREEMENT BETWEEN NORTH AMERICAN ELECTRIC RELIABILITY CORPORATION AND TEXAS REGIONAL ENTITY – A DIVISION OF ELECTRIC RELIABILITY  

E-Print Network (OSTI)

(“NERC”), an organization certified by the Federal Energy Regulatory Commission (“Commission”) pursuant to Section 215(c) of the Federal Power Act to establish and enforce Reliability Standards for the bulk power system, and the Texas Regional Entity – a Division of Electric Reliability Council of Texas, Inc. (“Texas RE”), an organization established to develop and enforce Reliability Standards within the geographic boundaries identified on Exhibit A to this Agreement, and for other purposes. NERC and Texas RE may be individually referred to herein as “Party ” or collectively as “Parties.” WITNESSETH WHEREAS, Subtitle A of the Electricity Modernization Act of 2005 added Section 215 to the Federal Power Act (16 U.S.C. § 824n) (hereafter “the Act”) and, among other things, provides for the establishment of an electric reliability organization (“ERO”) to develop and enforce Reliability Standards applicable to all owners, operators, and users of the bulk power system; WHEREAS, the Commission has adopted regulations for the implementation of the Act

unknown authors

2009-01-01T23:59:59.000Z

273

PASSIVE DETECTION OF VEHICLE LOADING  

SciTech Connect

The Digital Imaging and Remote Sensing Laboratory (DIRS) at the Rochester Institute of Technology, along with the Savannah River National Laboratory is investigating passive methods to quantify vehicle loading. The research described in this paper investigates multiple vehicle indicators including brake temperature, tire temperature, engine temperature, acceleration and deceleration rates, engine acoustics, suspension response, tire deformation and vibrational response. Our investigation into these variables includes building and implementing a sensing system for data collection as well as multiple full-scale vehicle tests. The sensing system includes; infrared video cameras, triaxial accelerometers, microphones, video cameras and thermocouples. The full scale testing includes both a medium size dump truck and a tractor-trailer truck on closed courses with loads spanning the full range of the vehicle's capacity. Statistical analysis of the collected data is used to determine the effectiveness of each of the indicators for characterizing the weight of a vehicle. The final sensing system will monitor multiple load indicators and combine the results to achieve a more accurate measurement than any of the indicators could provide alone.

Garrett, A.

2012-01-03T23:59:59.000Z

274

1995 Pacific Northwest Loads and Resources Study, Technical Appendix: Volume 1.  

SciTech Connect

The Pacific Northwest Loads and Resources Study (WhiteBook), is published annually by BPA, and establishes the planning basis for supplying electricity to customers. It serves a dual purpose. First, the White Book presents projections of regional and Federal system load and resource capabilities, along with relevant definitions and explanations. Second, the White Book serves as a benchmark for annual BPA determinations made pursuant to the 1981 regional power sales contracts. Specifically, BPA uses the, information in the White Book for determining the notice required when customers request to increase or decrease the amount of power purchased from BPA. Aside from these purposes, the White Book is used for input to BPA`s resource planning process. The White Book compiles information obtained from several formalized resource planning reports and data submittals, including those from the Northwest Power Planning Council (Council) and the Pacific Northwest Utilities Conference Committee (PNUCC).

United States. Bonneville Power Administration.

1995-12-01T23:59:59.000Z

275

Tennessee | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

entries for the individual states, shown below in the Authority listings. Typically energy must be delivered to an in-state utility or Load Serving Entity, and often only a...

276

North Carolina | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

shown below in the Authority listings. Typically energy must be delivered to an in-state utility or Load Serving Entity, and often only a portion of compliance targets may be...

277

Illinois | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

entries for the individual states, shown below in the Authority listings. Typically energy must be delivered to an in-state utility or Load Serving Entity, and often only a...

278

Univariate Modeling and Forecasting of Monthly Energy Demand Time Series  

E-Print Network (OSTI)

in this report. #12;i ABSTRACT These electricity demand forms and instructions ask load-serving entities and Instructions for Electricity Demand Forecasts. California Energy Commission, Electricity Supply Analysis.................................................................................................................................7 Form 1 Historic and Forecast Electricity Demand

Abdel-Aal, Radwan E.

279

Definition: Energy Emergency | Open Energy Information  

Open Energy Info (EERE)

Emergency Jump to: navigation, search Dictionary.png Energy Emergency A condition when a Load-Serving Entity has exhausted all other options and can no longer provide its...

280

Independent review of estimated load reductions for PJM's small customer load response pilot project  

E-Print Network (OSTI)

of Estimated Load Reductions for PJM’s Small Customer Loadof Estimated Load Reductions for PJM’s Small Customer LoadResponse Pilot Project Prepared for PJM Interconnection, LLC

Heffner, G.; Moezzi, M.; Goldman, C.

2004-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "load serving entity" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Automated fuel pin loading system  

DOE Patents (OSTI)

An automated loading system for nuclear reactor fuel elements utilizes a gravity feed conveyor which permits individual fuel pins to roll along a constrained path perpendicular to their respective lengths. The individual lengths of fuel cladding are directed onto movable transports, where they are aligned coaxially with the axes of associated handling equipment at appropriate production stations. Each fuel pin can be reciprocated axially and/or rotated about its axis as required during handling steps. The fuel pins are inserted as a batch prior to welding of end caps by one of two disclosed welding systems.

Christiansen, David W. (Kennewick, WA); Brown, William F. (West Richland, WA); Steffen, Jim M. (Richland, WA)

1985-01-01T23:59:59.000Z

282

High loading uranium fuel plate  

DOE Patents (OSTI)

Two embodiments of a high uranium fuel plate are disclosed which contain a meat comprising structured uranium compound confined between a pair of diffusion bonded ductile metal cladding plates uniformly covering the meat, the meat having a uniform high fuel loading comprising a content of uranium compound greater than about 45 Vol. % at a porosity not greater than about 10 Vol. %. In a first embodiment, the meat is a plurality of parallel wires of uranium compound. In a second embodiment, the meat is a dispersion compact containing uranium compound. The fuel plates are fabricated by a hot isostatic pressing process.

Wiencek, Thomas C. (Bolingbrook, IL); Domagala, Robert F. (Indian Head Park, IL); Thresh, Henry R. (Palos Heights, IL)

1990-01-01T23:59:59.000Z

283

37th Telecommunications Policy Research Conference, Sept. 2009 The Business Case of a Nationwide Wireless Network that Serves both Public  

E-Print Network (OSTI)

of public safety. In 2007, the U.S. Federal Communications Commission tried to establish a public-private again, and if so, how. Thus, this paper considers the viability of a public- private partnership penetration each year. We apply this model to both a public-private partnership that serves commercial

Peha, Jon M.

284

Penn State Faculty Handbook The Faculty Handbook is designed to serve as an orientation and reference guide for all faculty,  

E-Print Network (OSTI)

Penn State Faculty Handbook Welcome The Faculty Handbook is designed to serve as an orientation to locate and use a wide range of University resources. The Handbook contains information about the overall of the University #12;2 About the Faculty Handbook This handbook is intended for use as a general reference rather

Maroncelli, Mark

285

Interruptible load control for Taiwan Power Company  

SciTech Connect

Load management is the planning and implementation of those utility activities designed to influence customer use of electricity in ways that will produce desired changes in the utility's load shape. Interruptible load program is an option of load management which provides incentive rate to customers to interrupt or reduce the power demand during the system peak period or emergency condition. Therefore, how to design a proper incentive rate is the most important issue in implementing this program. This paper describes three alternatives designed for the interruptible load program, one of which was activated by Taiwan Power Company (Taipower) and some preliminary results were obtained. The effect of the interruptible load to the system peak demand reduction and the change of daily load curve for large industrial customers were analyzed. This paper estimates the avoided cost and design more appropriate incentive rate structure for interruptible load program.

Chen, C.S.; Leu, J.T. (Dept. of Electrical Engineering, National Sun Yat-Sen Univ., Kaohsiung (TW))

1990-05-01T23:59:59.000Z

286

Loads on drillpipe during jarring operations  

Science Conference Proceedings (OSTI)

Jarring implies heavy loads on the drillstring. The highest load on the drillpipe before jarring is at the rig floor. This paper discusses loads on drillpipe before, under, and after jarring. The authors show that for most situations, the shock wave from the jar impact does not imply additional load on the drillpipe compared with static load. The theoretical results are confirmed by measurements of a jarring operation with stuck point at [approx] 1,200 m measured depth. Loads on the drillpipe can be a limited factor in jarring operations because fear of possible additional loads from jarring dynamics may restrict the trip force (overpull) on the jar. The main conclusion is that dynamic jar forces do not give additional loads on drillpipe. This information can be used to set an optimal trip force on the jar.

Aarrestad, T.V.; Kyllingstad, A.

1994-12-01T23:59:59.000Z

287

1994 Pacific Northwest Loads and Resources Study.  

Science Conference Proceedings (OSTI)

The 1994 Pacific Northwest Loads and Resources Study presented herein establishes a picture of how the agency is positioned today in its loads and resources balance. It is a snapshot of expected resource operation, contractual obligations, and rights. This study does not attempt to present or analyze future conservation or generation resource scenarios. What it does provide are base case assumptions from which scenarios encompassing a wide range of uncertainties about BPA`s future may be evaluated. The Loads and Resources Study is presented in two documents: (1) this summary of Federal system and Pacific Northwest region loads and resources and (2) a technical appendix detailing the loads and resources for each major Pacific Northwest generating utility. This analysis updates the 1993 Pacific Northwest Loads and Resources Study, published in December 1993. In this loads and resources study, resource availability is compared with a range of forecasted electricity consumption. The Federal system and regional analyses for medium load forecast are presented.

United States. Bonneville Power Administration.

1994-12-01T23:59:59.000Z

288

Plug Load Behavioral Change Demonstration Project  

SciTech Connect

This report documents the methods and results of a plug load study of the Environmental Protection Agency's Region 8 Headquarters in Denver, Colorado, conducted by the National Renewable Energy Laboratory. The study quantified the effect of mechanical and behavioral change approaches on plug load energy reduction and identified effective ways to reduce plug load energy. Load reduction approaches included automated energy management systems and behavioral change strategies.

Metzger, I.; Kandt, A.; VanGeet, O.

2011-08-01T23:59:59.000Z

289

Spinning reserve from hotel load response  

SciTech Connect

Even though preliminary tests were not conducted during times of highest system or hotel loading during the summer, they showed that hotel load can be curtailed by 22 to 37 percent depending on the outdoor temperature and time of day. Full response occurred in 12 to 60 seconds from when the system operator's command to shed load was issued and the load drop was very rapid. (author)

Kirby, Brendan; Kueck, John; Laughner, Theo; Morris, Keith

2008-12-15T23:59:59.000Z

290

Load Shape Library Version 1.0  

Science Conference Proceedings (OSTI)

The downloadable report details EPRI's efforts to develop a framework of a load database and web-accessible repository of end-use and whole-premise data for application to energy efficiency assessments. The tool provides access to the best available end-use load data and whole-premise data by sector, region and building type. Improved end-use load research data will benefit load forecasters, system planners, energy efficiency program managers and rate design analysts by facilitating integration ...

2013-02-12T23:59:59.000Z

291

Load Scheduling with Profile Information  

E-Print Network (OSTI)

Abstract Within the past five years, many manufactureshave added hardware performance counters to their microprocessors to generate profile data cheaply.Translating aggregate data such as basic block execution frequencies from the executable to the com-piler intermediate representation is fairly straightforward. In this paper, we show how to use Com-paq's DCPI tool to determine load latencies which are at a fine, instruction granularity and then usethem to provide fodder for improving instruction scheduling. We validate our heuristic for usingDCPI latency data to classify loads as hits and misses against simulation numbers, demonstratingthat we can gather correct latencies cheaply at runtime. We map our classification into the Multiflowcompiler's intermediate representation, and use a locality sensitive Balanced scheduling algorithm. Ourexperiments illustrate that our algorithm has the potential to improve run times by up to 10 % on a Com-paq Alpha when compared to Balanced scheduling, but that a variety of pitfalls make consistent im-provements difficult to attain. 1 Introduction In this paper, we explore how to use hardware per-formance counters to produce fine grain latency information to improve compiler scheduling. We usethis information to hide latencies with any avail\\Lambda The authors

unknown authors

1999-01-01T23:59:59.000Z

292

Glossary of terms related to load management  

Science Conference Proceedings (OSTI)

Part I of the Glossary of Terms related to Load Management has been prepared by the Terminology Task Force of the Load Management Subcommittee. The glossary contains many definitions of terms used by the electric utility industry concerning the subject of Load Management. The terms are listed in alphabetical order and cross-referenced where necessary.

Gellings, C.W.

1985-09-01T23:59:59.000Z

293

Properly Evaluating load-following products  

SciTech Connect

The authors briefly survey the jurisdictions where load-following products have been successfully used, examine the characteristics of the load-following products, and explain the shortcomings and inaccurate conclusions of previous analyses. A more thorough analysis reveals that the load-following products fulfill the public policy objectives for which they have been designed and do not adversely impact wholesale electricity markets.

Cavicchi, Joseph; Lemon, Andrew

2009-01-15T23:59:59.000Z

294

Adaptive load sharing for network processors  

Science Conference Proceedings (OSTI)

A novel scheme for processing packets in a router is presented that provides load sharing among multiple network processors distributed within the router. It is complemented by a feedback control mechanism designed to prevent processor overload. Incoming ... Keywords: computer networks, feedback control, load balancing, load sharing, packet processing, router architecture

Lukas Kencl; Jean-Yves Le Boudec

2008-04-01T23:59:59.000Z

295

Efficient real-time divisible load scheduling  

Science Conference Proceedings (OSTI)

Providing QoS and performance guarantees to arbitrarily divisible loads has become a significant problem for many cluster-based research computing facilities. While progress is being made in scheduling arbitrarily divisible loads, current approaches ... Keywords: Arbitrarily divisible loads, Cluster computing, Real-time computing, Scheduling efficiency

Anwar Mamat; Ying Lu; Jitender Deogun; Steve Goddard

2012-12-01T23:59:59.000Z

296

Domestic load scheduling using genetic algorithms  

Science Conference Proceedings (OSTI)

An approach using a genetic algorithm to optimize the scheduling of domestic electric loads, according to technical and user-defined constraints and input signals, is presented and illustrative results are shown. The aim is minimizing the end-user's ... Keywords: automated energy management, domestic load scheduling, electric loads, genetic algorithms

Ana Soares; Állvaro Gomes; Carlos Henggeler Antunes; Hugo Cardoso

2013-04-01T23:59:59.000Z

297

Neural-wavelet Methodology for Load Forecasting  

Science Conference Proceedings (OSTI)

Intelligent demand-side management represents a future trend of power system regulation. A key issue in intelligent demand-side management is accurate prediction of load within a local area grid (LAG), which is defined as a set of customers with an appropriate ... Keywords: load forecasting, load identification, neural-wavelet

Rong Gao; Lefteri H. Tsoukalas

2001-05-01T23:59:59.000Z

298

Value of Demand Response Theoretical thoughts Klaus Skytte  

E-Print Network (OSTI)

/MWh consumer surplus CP MWhqload MB #12;Determination of load profile MWh/h qt load Timet #12 Companies Private households #12;Determination of load each hour /MWh CP MWhqload MB #12;Consumer surplus the welfare losses in each period. The load-serving entity might determine the consumer price (CP

299

Critically loaded queueing models that are throughput suboptimal  

E-Print Network (OSTI)

This paper introduces and analyzes the notion of throughput suboptimality for many-server queueing systems in heavy traffic. The queueing model under consideration has multiple customer classes, indexed by a finite set $\\mathcal{I}$, and heterogenous, exponential servers. Servers are dynamically chosen to serve customers, and buffers are available for customers waiting to be served. The arrival rates and the number of servers are scaled up in such a way that the processes representing the number of class-$i$ customers in the system, $i\\in\\mathcal{I}$, fluctuate about a static fluid model, that is assumed to be critically loaded in a standard sense. At the same time, the fluid model is assumed to be throughput suboptimal. Roughly, this means that the servers can be allocated so as to achieve a total processing rate that is greater than the total arrival rate. We show that there exists a dynamic control policy for the queueing model that is efficient in the following strong sense: Under this policy, for every f...

Atar, Rami; 10.1214/08-AAP551

2009-01-01T23:59:59.000Z

300

Medical Students must obtain approval to invite outside commercial entities and vendors to exhibit at student events and/or other activities.  

E-Print Network (OSTI)

Medical Students must obtain approval to invite outside commercial entities and vendors to exhibit at student events and/or other activities. Medical students must adhere to UCDHS policies under Hospital Chapter 270, Pharmaceuticals Manufacturer's Representatives, the Office of Medical Education Room Usage

Leistikow, Bruce N.

Note: This page contains sample records for the topic "load serving entity" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Documentation of the status of international geothermal power plants and a list by country of selected geothermally active governmental and private sector entities  

DOE Green Energy (OSTI)

This report includes the printouts from the International Geothermal Power Plant Data Base and the Geothermally Active Entity Data Base. Also included are the explanation of the abbreviations used in the power plant data base, maps of geothermal installations by country, and data base questionnaires and mailing lists.

Not Available

1992-10-01T23:59:59.000Z

302

1993 Pacific Northwest Loads and Resources Study.  

SciTech Connect

The Loads and Resources Study is presented in three documents: (1) this summary of Federal system and Pacific Northwest region loads and resources; (2) a technical appendix detailing forecasted Pacific Northwest economic trends and loads, and (3) a technical appendix detailing the loads and resources for each major Pacific Northwest generating utility. In this loads and resources study, resource availability is compared with a range of forecasted electricity consumption. The forecasted future electricity demands -- firm loads -- are subtracted from the projected capability of existing and {open_quotes}contracted for{close_quotes} resources to determine whether Bonneville Power Administration (BPA) and the region will be surplus or deficit. If resources are greater than loads in any particular year or month, there is a surplus of energy and/or capacity, which BPA can sell to increase revenues. Conversely, if firm loads exceed available resources, there is a deficit of energy and/or capacity, and additional conservation, contract purchases, or generating resources will be needed to meet load growth. The Pacific Northwest Loads and Resources Study analyzes the Pacific Northwest`s projected loads and available generating resources in two parts: (1) the loads and resources of the Federal system, for which BPA is the marketing agency; and (2) the larger Pacific Northwest regional power system, which includes loads and resource in addition to the Federal system. The loads and resources analysis in this study simulates the operation of the power system under the Pacific Northwest Coordination Agreement (PNCA) produced by the Pacific Northwest Coordinating Group. This study presents the Federal system and regional analyses for five load forecasts: high, medium-high, medium, medium-low, and low. This analysis projects the yearly average energy consumption and resource availability for Operating Years (OY) 1994--95 through 2003--04.

United States. Bonneville Power Administration.

1993-12-01T23:59:59.000Z

303

Low cutter load raise head  

SciTech Connect

A raise head having a multiplicity of cutters for enlarging a pilot hole into a larger diameter hole by disintegrating the earth formations that surround the pilot hole is provided that will require lower cutter loads to penetrate the formations being bored by directing the rock fracture planes toward the pilot hole forcing the rock to yield with less input energy. The cutters are positioned on the raise head to provide an earth formation contact profile with a major portion of said earth formation contact profile extending outward and upward from said pilot hole. The included angle between the major portion of the earth formation contact profile and the axis of the pilot hole is less than 90/sup 0/.

Saxman, W.C.

1981-03-31T23:59:59.000Z

304

Kinesin's backsteps under mechanical load  

E-Print Network (OSTI)

Kinesins move processively toward the plus end of microtubules by hydrolyzing ATP for each step. From an enzymatic perspective, the mechanism of mechanical motion coupled to the nucleotide chemistry is often well explained using a single-loop cyclic reaction. However, several difficulties arise in interpreting kinesin's backstepping within this framework, especially when external forces oppose the motion of kinesin. We review evidence, such as an ATP-independent stall force and a slower cycle time for backsteps, that has emerged to challenge the idea that kinesin backstepping is due to ATP synthesis, i.e., the reverse cycle of kinesin's forward-stepping chemomechanics. Supplementing the conventional single-loop chemomechanics with routes for ATP-hydrolyzing backward steps and nucleotide-free steps, especially under load, gives a better physical interpretation of the experimental data on backsteps.

Changbong Hyeon; Stefan Klumpp; José N. Onuchic

2009-04-18T23:59:59.000Z

305

High payload six-axis load sensor  

DOE Patents (OSTI)

A repairable high-payload six-axis load sensor includes a table, a base, and at least three shear-pin load transducers removably mounted between the table and the base. Removable mounting permits easy replacement of damaged shear pins. Preferably, the shear-pin load transducers are responsive to shear forces imparted along the two axes perpendicular to an axis of minimum sensitivity characteristic of the transducer. Responsive to an applied shear force, each shear-pin load transducer can produce an electrical signal proportional to the reaction force. The load sensor can further include a structure for receiving the proportional electrical signals and computing the applied load corresponding to the proportional electrical signals. The computed load can be expressed in terms of a three-dimensional XYZ Cartesian coordinate system.

Jansen, John F. (Knoxville, TN); Lind, Randall F. (Knoxville, TN)

2003-01-01T23:59:59.000Z

306

Analysis Methodology for Industrial Load Profiles  

E-Print Network (OSTI)

A methodology is provided for evaluating the impact of various demand-side management (DSM) options on industrial customers. The basic approach uses customer metered load profile data as a basis for the customer load shape. DSM technologies are represented as load shapes and are used as a basis for altering the customers existing measured load shape. The impact of load shape changes on the customer is evaluated in terms of a change in the electric bill by using a software analytical tool called LOADEXPERT™. The software calculates the customer's bill for a particular rate structure and a given load shape. The output data from LOADEXPERT™ are used to calculate the rate of return on the DSM technology investment. Other uses of load profile data are provided.

Reddoch, T. W.

1991-06-01T23:59:59.000Z

307

A Novel Approach to Determining Motor Load  

E-Print Network (OSTI)

Properly sized electric motors are essential if industrial plant efficiency is to be optimized and energy costs minimized. Because of the difficulty in making power measurements on three phase motors, loading is rarely, if ever, checked. A simple indication of motor load can be achieved by measuring operating speed because speed and load are almost linearly related. The decrease in motor speed from no load conditions, referred to as slip, can be determined with a non-contact, optical tachometer. Field measurements of motor slip were conducted at a textile plant to quantify motor load conditions. To verify the relationship between operating speed and load, measurements of motor power consumption on a representative number of motors were also conducted. The results of the motor survey, including number of motors, size, and load, are summarized in this paper along with an estimate of the savings from replacing oversized motors.

Brown, M.

1992-04-01T23:59:59.000Z

308

Exploring the inherent benefits of RFID and automated self-serve checkouts in a B2C environment  

Science Conference Proceedings (OSTI)

Automated identification services such as RFID and self-serve checkouts that require many different technological components in order to successfully operate and be accepted in a B2C (Business-to-Customer) environment. In theory, ... Keywords: B2C, CRM, RFID, SCM, autoID, automatic identification, business information systems, business-to-, customer, customer relationship management, radio frequency identification, retail grocery, retailing, self service checkouts, self-checkout, strategy, supply chain management, technology adoption

Alan D. Smith

2005-07-01T23:59:59.000Z

309

Static load test of Arquin-designed CMU wall.  

Science Conference Proceedings (OSTI)

The Arquin Corporation has developed a new method of constructing CMU (concrete masonry unit) walls. This new method uses polymer spacers connected to steel wires that serve as reinforcing as well as means of accurately placing the spacers so that the concrete block can be dry stacked. The hollows of the concrete block used in constructing the wall are then filled with grout. As part of a New Mexico Small Business Assistance Program (NMSBAP), Sandia National Laboratories conducted a series of tests that statically loaded wall segments to compare the Arquin method to a more traditional method of constructing CMU walls. A total of 12 tests were conducted, three with the Arquin method using a W5 reinforcing wire, three with the traditional method of construction using a number 3 rebar as reinforcing, three with the Arquin method using a W2 reinforcing wire, and three with the traditional construction method but without rebar. The results of the tests showed that the walls constructed with the Arquin method and with a W5 reinforcing wire withstood more load than any of the other three types of walls that were tested.

Jensen, Richard Pearson; Cherry, Jeffery L.

2008-12-01T23:59:59.000Z

310

Dynamic load test of Arquin-designed CMU wall.  

SciTech Connect

The Arquin Corporation has developed a new method of constructing CMU (concrete masonry unit) walls. This new method uses polymer spacers connected to steel wires that serve as reinforcing as well as a means of accurately placing the spacers so that the concrete block can be dry stacked. The hollows of the concrete block are then filled with grout. As part of a New Mexico Small Business Assistance Program (NMSBA), Sandia National Laboratories conducted a series of tests that dynamically loaded wall segments to compare the performance of walls constructed using the Arquin method to a more traditional method of constructing CMU walls. A total of four walls were built, two with traditional methods and two with the Arquin method. Two of the walls, one traditional and one Arquin, had every third cell filled with grout. The remaining two walls, one traditional and one Arquin, had every cell filled with grout. The walls were dynamically loaded with explosive forces. No significant difference was noted between the performance of the walls constructed by the Arquin method when compared to the walls constructed by the traditional method.

Jensen, Richard Pearson

2010-02-01T23:59:59.000Z

311

Entity State Ownership  

U.S. Energy Information Administration (EIA) Indexed Site

Northern California Power Agny Northern California Power Agny CA Political Subdivision 1 366,159 20,892.0 5.71 Constellation NewEnergy, Inc CT Power Marketer 2 33,816 2,550.5 7.54 HESS CORPORATION CT Power Marketer 1 106,596 5,490.0 5.15 American PowerNet DC Power Marketer 1 148,928 8,161.0 5.48 Reliant Energy Northeast LLC DC Power Marketer 1 200,803 13,152.0 6.55 Constellation NewEnergy, Inc IL Power Marketer 3 781,822 37,958.5 4.86 Massachusetts Bay Trans Authority MA Political Subdivision 3 55,875 6,106.0 10.93 NextEra Energy Power Marketing MA Power Marketer 1 284,229 7,954.4 2.80 American PowerNet MD Power Marketer 1 121,566 6,618.0 5.44 Constellation NewEnergy, Inc MD Power Marketer 2 151,684 13,222.6 8.72 PPL EnergyPlus LLC MD Power Marketer 1 9,108 544.5 5.98 Reliant Energy Northeast LLC MD Power Marketer 1 157,011 10,282.7 6.55 Constellation NewEnergy, Inc

312

Entity State Ownership  

U.S. Energy Information Administration (EIA) Indexed Site

3,912 3,912 142,255 16,970.0 11.93 Alaska Power and Telephone Co AK Investor Owned 4,803 24,391 7,470.0 30.63 Alaska Village Elec Coop, Inc AK Cooperative 6,148 31,085 19,275.0 62.01 Anchorage Municipal Light and Power AK Municipal 24,443 146,789 17,221.2 11.73 Barrow Utils & Elec Coop, Inc AK Cooperative 1,471 11,511 1,364.0 11.85 Bethel Utilities Corp AK Investor Owned 1,671 10,677 5,990.0 56.10 Chugach Electric Assn Inc AK Cooperative 69,495 549,748 76,083.0 13.84 City & Borough of Sitka - (AK) AK Municipal 3,669 47,899 4,570.0 9.54 City of Petersburg - (AK) AK Municipal 1,354 20,803 2,010.2 9.66 City of Seward - (AK) AK Municipal 2,064 16,488 3,344.0 20.28 City of Unalaska - (AK) AK Municipal 686 4,009 1,997.6 49.83 City of Wrangell - (AK) AK Municipal 1,170 15,273 1,604.0 10.50 Copper Valley Elec Assn, Inc AK Cooperative

313

Entity State Ownership  

U.S. Energy Information Administration (EIA) Indexed Site

41 41 71,558 3,893.2 5.44 City of Corona - (CA) CA Municipal 7 40,918 3,592.4 8.78 Commerce Energy, Inc. CA Power Marketer 7,862 391,246 24,362.0 6.23 Constellation NewEnergy, Inc CA Power Marketer 38 2,158,578 102,576.2 4.75 Direct Energy Business CA Power Marketer 29 241,690 14,996.0 6.20 Marin Energy Authority CA Power Marketer 6 31,782 2,241.5 7.05 Noble Americas Energy Solutions LLC CA Power Marketer 56 1,875,061 126,908.8 6.77 Pilot Power Group Inc CA Power Marketer 41 498,646 29,521.7 5.92 Shell Energy North America (US), L.P. CA Power Marketer 31 2,259,297 98,489.5 4.36 Constellation NewEnergy, Inc CT Power Marketer 574 1,159,360 96,511.6 8.32 Farmington River Power Company CT Investor Owned 1 23,588 1,484.4 6.29 HOP Energy, LLC CT Power Marketer 2 5,198 409.2 7.87 Integrys Energy Services, Inc. CT Power Marketer 63 109,635

314

Entity State Ownership  

U.S. Energy Information Administration (EIA) Indexed Site

City of North Little Rock - (AR) City of North Little Rock - (AR) AR Municipal 1 349 41.0 11.75 Entergy Arkansas Inc AR Investor Owned 1 114 11.0 9.65 City & County of San Francisco CA Municipal 1 103,268 4,130.0 4.00 City of Pasadena - (CA) CA Municipal 1 9,538 1,365.5 14.32 Los Angeles Department of Water & Power CA Municipal 2 16,946 2,655.0 15.67 Sacramento Municipal Util Dist CA Political Subdivision 1 28,918 3,485.2 12.05 San Diego Gas & Electric Co CA Investor Owned 4 95,213 6,744.0 7.08 Southern California Edison Co CA Investor Owned 1 51,664 6,759.0 13.08 WAPA-- Western Area Power Administration CA Federal 1 14,049 299.0 2.13 Public Service Co of Colorado CO Investor Owned 1 52,471 5,083.0 9.69 Florida Power & Light Co FL Investor Owned 1 80,521 6,752.0 8.39 JEA FL Municipal 1 3,374 341.1 10.11 Georgia Power Co GA Investor Owned 1 156,955

315

Entity State Ownership  

U.S. Energy Information Administration (EIA) Indexed Site

2,174 2,174 129,783 12,857.0 9.91 Alaska Power and Telephone Co AK Investor Owned 2,173 40,397 10,705.0 26.50 Alaska Village Elec Coop, Inc AK Cooperative 1,775 42,871 23,433.0 54.66 Anchorage Municipal Light and Power AK Municipal 6,304 953,876 83,738.0 8.78 Barrow Utils & Elec Coop, Inc AK Cooperative 400 38,069 3,929.0 10.32 Bethel Utilities Corp AK Investor Owned 1,017 30,229 16,102.0 53.27 Chugach Electric Assn Inc AK Cooperative 9,204 574,284 67,370.0 11.73 City & Borough of Sitka - (AK) AK Municipal 1,622 58,534 5,638.0 9.63 City of Petersburg - (AK) AK Municipal 717 9,064 1,030.5 11.37 City of Seward - (AK) AK Municipal 503 8,651 1,869.0 21.60 City of Unalaska - (AK) AK Municipal 242 11,183 4,906.4 43.87 City of Wrangell - (AK) AK Municipal 778 19,919 2,132.0 10.70 Copper Valley Elec Assn, Inc AK Cooperative 797 65,757

316

Entity State Ownership  

U.S. Energy Information Administration (EIA) Indexed Site

354 354 148,820 7,268.5 4.88 Calpine Power America LLC CA Power Marketer 1 1,072,508 54,458.0 5.08 City of Corona - (CA) CA Municipal 859 65,933 5,749.5 8.72 Commerce Energy, Inc. CA Power Marketer 23,386 596,604 37,753.0 6.33 Constellation NewEnergy, Inc CA Power Marketer 362 4,777,373 250,287.4 5.24 Direct Energy Business CA Power Marketer 480 4,028,166 249,932.0 6.20 Glacial Energy Holdings CA Power Marketer 98 74,913 5,896.2 7.87 Liberty Power Corp. CA Power Marketer 26 62,311 3,307.0 5.31 Marin Energy Authority CA Power Marketer 45,658 535,094 41,883.2 7.83 Noble Americas Energy Solutions LLC CA Power Marketer 201 7,533,445 471,887.5 6.26 Northern California Power Agny CA Political Subdivision 1 366,159 20,892.0 5.71 Pilot Power Group Inc CA Power Marketer 921 1,468,892 84,041.1 5.72 Shell Energy North America (US), L.P.

317

Entity State Ownership  

U.S. Energy Information Administration (EIA) Indexed Site

94 94 127,106 11,993.0 9.44 Chugach Electric Assn Inc AK Cooperative 7 54,804 5,902.0 10.77 City & Borough of Sitka - (AK) AK Municipal 15 4,968 476.0 9.58 City of Petersburg - (AK) AK Municipal 39 19,905 2,208.6 11.10 City of Seward - (AK) AK Municipal 126 33,599 5,828.0 17.35 City of Unalaska - (AK) AK Municipal 16 27,024 10,572.0 39.12 Cordova Electric Coop, Inc AK Cooperative 5 8,004 1,902.0 23.76 Golden Valley Elec Assn Inc AK Cooperative 496 855,521 160,872.2 18.80 Homer Electric Assn Inc AK Cooperative 23 127,076 11,094.0 8.73 Ketchikan Public Utilities AK Municipal 13 24,453 2,046.9 8.37 Kodiak Electric Assn Inc AK Cooperative 102 87,040 14,770.0 16.97 Alabama Power Co AL Investor Owned 5,839 22,157,722 1,345,850.0 6.07 Albertville Municipal Utilities Board AL Municipal 18 293,204 21,775.0 7.43 Arab Electric Coop Inc AL

318

Contextually-related Entities  

Science Conference Proceedings (OSTI)

... Other weak blue-chip issues included Chevron, which went down 2 to 64 7/8 in Big Board composite trading of 1.3 million shares; Goodyear Tire & ...

2004-10-27T23:59:59.000Z

319

Investigation of residential central air conditioning load shapes in NEMS  

E-Print Network (OSTI)

of Residential Central Air Conditioning Load Shapes in NEMSof Residential Central Air Conditioning Load Shapes in NEMSof Residential Central Air Conditioning Load Shapes in NEMS

Hamachi LaCommare, Kristina; Marnay, Chris; Gumerman, Etan; Chan, Peter; Rosenquist, Greg; Osborn, Julie

2002-01-01T23:59:59.000Z

320

Wind loading on solar collectors  

DOE Green Energy (OSTI)

The present design methodology for the determination of wind loading on the various solar collectors has been reviewed and assessed. The total force coefficients of flat plates of aspect ratios 1.0 and 3.0, respectively, at various angles of attack obtained by using the guidelines of the ANSI A58.1-1982, have been compared with those obtained by using the methodology of the ASCE Task Committee, 1961, and the experimental results of the full-scale test of heliostats by Peglow. The turbulent energy spectra, currently employed in the building code, are compared with those of Kaimal et al., Lumley, and Ponofsky for wind velocities of 20.0 m/s and 40.24 m/s at an elevation of 9.15 m. The longitudinal spectra of the building code overestimates the Kaimal spectra in the frequency range of 0.007 Hz to 0.08 Hz and underestimates beyond the frequency of 0.08 Hz. The peak angles of attack, on the heliostat, stowed in horizontal position, due to turbulent vertical and lateral components of wind velocity, have been estimated by using Daniel's methodology for three wind velocities and compared with the value suggested by the code. The experimental results of a simple test in the laboratory indicate the feasibility of decreasing the drag forces of the flat plate by reducing the solidity ratio.

Bhaduri, S.; Murphy, L.M.

1985-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "load serving entity" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

On Load Balancing in a Dense Wireless  

E-Print Network (OSTI)

We study the load balancing problem in a dense wireless multihop network, where a typical path consists of large number of hops, i.e., the spatial scales of a typical distance between source and destination, and mean distance between the neighbouring nodes are strongly separated. In this limit, we present a general framework for analysing the traffic load resulting from a given set of paths and traffic demands. We formulate the load balancing problem as a minmax problem and give two lower bounds for the achievable minimal maximum traffic load. The framework is illustrated by an example of uniformly distributed traffic demands in a unit disk with a few families of paths given in advance. With these paths we are able to decrease the maximum traffic load by factor of 33 40% depending on the assumptions. The obtained traffic load level also comes quite near the tightest lower bound.

Multihop Network Esa; Esa Hyytiä

2006-01-01T23:59:59.000Z

322

Profile Guided Load Marking for Memory Renaming  

E-Print Network (OSTI)

Memory operations remain a significant bottleneck in dynamically scheduled pipelined processors, due in part to the inability to statically determine the existence of memory address dependencies. Hardware memory renaming techniques have been proposed which predict which stores a load might be dependent upon. These prediction techniques can be used to speculatively forward a value from a predicted store dependency to a load through a value prediction table; however, these techniques require large and time-consuming hardware tables. In this paper we propose a software-guided approach for identifying dependencies between store and load instructions and the Load Marking (LM) architecture to communicate these dependencies to the hardware. Compiler analysis and profiles are used to find important store/load relationships, and these relationships are identified during execution via hints or an n-bit tag. For those loads that are not marked for renaming, we then use additional profiling inform...

Glenn Reinman; Brad Calder; Dean Tullsen; Gary Tyson; Todd Austin

1998-01-01T23:59:59.000Z

323

Assessment of Industrial-Sector Load Shapes  

Science Conference Proceedings (OSTI)

The load shapes of industrial-sector customers are becoming increasingly important for utility forecasting, marketing, and demand-side management planning and evaluation activities. This report analyzes load shapes for various industry segments and investigates the transfer of these load shapes across service territories. This report is available only to funders of Program 101A or 101.001. Funders may download this report at http://my.primen.com/Applications/DE/Community/index.asp .

1993-02-18T23:59:59.000Z

324

Trends in electric utility load duration curves  

SciTech Connect

This report documents the development and analysis of annual and quarterly load duration curves for each of the 10 Federal regions. The report describes analyses performed to test for changes in load duration curve shapes over time. These analyses are intended to aid the electric utility analyses and modeling activities of the Energy Information Administration (EIA) by expanding the understanding of current and expected load duration curve shapes. 7 figs., 13 tabs.

1984-12-01T23:59:59.000Z

325

Loads, capacity, and failure rate modeling  

SciTech Connect

Both failure rate and load capacity (stress-strength) interferenece methodologies are employed in the reliability analysis at nuclear facilities. Both of the above have been utilized in a heuristic failure rate model in terms of load capacity inference. Analytical solutions are used to demonstrate that infant mortality and random aging failures may be expressed implicity in terms of capacity variability, load variability, and capacity deterioration, and that mode interactions play a role in the formation of the bathtub curve for failure rates.

Lewis, E.E.; Chen, Hsin-Chieh

1994-12-31T23:59:59.000Z

326

1991 Pacific Northwest Loads and Resources Study.  

SciTech Connect

This study establishes the Bonneville Power Administration's (BPA) planning basis for supplying electricity to BPA customers. The Loads and Resources Study is presented in three documents: (1) this summary of federal system and Pacific Northwest region loads and resources; (2) a technical appendix detailing forecasted Pacific Northwest economic trends and loads, and (3) a technical appendix detailing the loads and resources for each major Pacific Northwest generating utility. This analysis updates our 1990 study. BPS's long-range planning incorporates resource availability with a range of forecasted electrical consumption. The forecasted future electrical demands-firm loads--are subtracted from the projected capability of existing resources to determine whether BPA and the region will be surplus or deficit. If resources are greater than loads in any particular year or month, there is a surplus of energy and/or capacity, which BPA can sell to increase revenues. Conversely, if firm loads exceed available resources, there is a deficit of energy and/or capacity, then additional conservation, contract purchases, or generating resources will be needed to meet load growth. This study analyzes the Pacific Northwest's projected loads and available generating resources in two parts: (1) the loads and resources of the federal system, for which BPA is the marketing agency; and (2) the larger Pacific Northwest regional profile, which includes loads and resources in addition to the federal system. This study presents the federal system and regional analyses for five load forecasts: high, medium-high, medium, medium-low, and low. This analysis projects the yearly average energy consumption and resource availability for 1992- 2012.

United States. Bonneville Power Administration.

1991-12-01T23:59:59.000Z

327

Reservoir compaction loads on casings and liners  

Science Conference Proceedings (OSTI)

Pressure drawdown due to production from a reservoir causes compaction of the reservoir formation which induces axial and radial loads on the wellbore. Reservoir compaction loads increase during the production life of a well, and are greater for deviated wells. Presented here are casing and liner loads at initial and final pressure drawdowns for a particular reservoir and at well deviation angles of 0 to 45 degrees.

Wooley, G.R.; Prachner, W.

1984-09-01T23:59:59.000Z

328

NORMAL LOAD BEARING BY SITE SPECIFIC CANISTER  

Science Conference Proceedings (OSTI)

The overall purpose of this calculation is to perform a preliminary analysis of the Site Specific Canister/Basket, subject to static gravity loads that include the self weight of the Canister Shell, the Basket, the Spent Nuclear Fuel, the Shield Plug and the related hardware, so that the loads are approximately known for sizing purposes. Based on these loads the stress levels in various components of the Site Specific Canister/Basket are evaluated.

NA

2005-03-23T23:59:59.000Z

329

Measured Peak Equipment Loads in Laboratories  

SciTech Connect

This technical bulletin documents measured peak equipment load data from 39 laboratory spaces in nine buildings across five institutions. The purpose of these measurements was to obtain data on the actual peak loads in laboratories, which can be used to rightsize the design of HVAC systems in new laboratories. While any given laboratory may have unique loads and other design considerations, these results may be used as a 'sanity check' for design assumptions.

Mathew, Paul A.

2007-09-12T23:59:59.000Z

330

300 Billion Served  

Science Conference Proceedings (OSTI)

Understanding the public's sources, perceptions, uses, and values of weather forecasts is integral to providing those forecasts in the most societally beneficial manner. To begin developing this knowledge, we conducted a nationwide survey with ...

Jeffrey K. Lazo; Rebecca E. Morss; Julie L. Demuth

2009-06-01T23:59:59.000Z

331

Testimonials: Why Serve?  

Science Conference Proceedings (OSTI)

... So I've picked up so much in leadership management skills just by ... better leadership skills, a major level of excitement and energy, and more ...

2013-06-27T23:59:59.000Z

332

Load relaxation studies of zircaloy-4  

SciTech Connect

The results of the present work have shown (1) the load relaxation data of Zircaloy-4 in the temperature range of 200/sup 0/C to 385/sup 0/C can be represented by the phenomenological model based on Hart's plastic equation of state; (2) the room temperature load relaxation data reflect the effects of deformation twinning; (3) at higher temperatures the load relaxation data suggest the contribution of grain boundary sliding; and (4) the effects of strain aging can be identified based on the load relaxation data.

Huang, F.H.; Sabol, G.P.; McDonald, S.G.; Li, C.Y.

1976-01-01T23:59:59.000Z

333

OpenEI Community - load profile  

Open Energy Info (EERE)

/0 en Commercial and /0 en Commercial and Residential Hourly Load Data Now Available on OpenEI! http://en.openei.org/community/blog/commercial-and-residential-hourly-load-data-now-available-openei <span class=Load data" src="http://en.openei.org/community/files/load_data_figure_small.jpg" style="width:527px; height:285px" title="" />Image source: NREL 

Files: 
application/zip icon

334

NREL: Vehicle Ancillary Loads Reduction - Laboratory Capabilities  

NLE Websites -- All DOE Office Websites (Extended Search)

VALR Lab. NREL's Vehicle Ancillary Loads Reduction Laboratory houses ADAM, our advanced thermal manikin, as well as a passenger compartment climate simulator, testing equipment...

335

Building Energy Software Tools Directory: Load Express  

NLE Websites -- All DOE Office Websites (Extended Search)

Create project files with Load Express in just 4 easy steps. Select a weather profile, enter simulation parameters, define the zonesrooms in the building and create air handler...

336

Effect of Nonproportional Loadings on Ductile Fracture  

Science Conference Proceedings (OSTI)

Abstract Scope, This study aims at understanding the effects of load path ... D-2: Forging of Magnesium Alloy by Impulsive Energy at Room Temperature.

337

Thermoplastic Flour Containing Eugenol-loaded Chitosan ...  

Science Conference Proceedings (OSTI)

Presentation Title, Thermoplastic Flour Containing Eugenol-loaded Chitosan ... Properties of AA 7075 Reinforced with Nanometric ZrO2 Obtained by Ball-milling.

338

Building Energy Software Tools Directory : HVAC Residential Load...  

NLE Websites -- All DOE Office Websites (Extended Search)

HVAC Residential Load Calcs HD for the iPad Back to Tool HVAC Residential Load Calcs HD screenshot HVAC Residential Load Calcs HD screenshot HVAC Residential Load Calcs HD...

339

Methods for Analyzing Electric Load Shape and its Variability  

E-Print Network (OSTI)

15 Figure 12: Load profile by day of week, averaged over thebetween the average load profile and the profile of a givenfrom the average load profile. Figure 12: Load profile by

Price, Philip

2010-01-01T23:59:59.000Z

340

Decentralized agent-based underfrequency load shedding  

Science Conference Proceedings (OSTI)

As part of the transition to a smart grid efforts are being made to decentralize control of electric power systems and modernize protection schemes that are currently in use. One specific application of distributed control is underfrequency load shedding ... Keywords: UFLS, Underfrequency load shedding, intelligent agents

Sara Mullen; Getiria Onsongo

2010-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "load serving entity" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Design Ground Snow Loads for Ohio  

Science Conference Proceedings (OSTI)

The weight of snow with a mean recurrence interval of 50 years, called the design ground snow load, is used by engineers and planners to estimate the weight of snow that roofs must be designed to support National maps of ground snow load have ...

Thomas W. Schmidlin; Dennis J. Edgell; Molly A. Delaney

1992-06-01T23:59:59.000Z

342

Apparatus for loading a band saw blade  

DOE Patents (OSTI)

A band saw blade is loaded between pairs of guide wheels upon tensioning the blade by guiding the blade between pairs of spaced guide plates which define converging slots that converge toward the guide wheels. The approach is particularly useful in loading blades on underwater band saw machines used to cut radioactive materials. 2 figs.

Reeves, S.R.

1990-03-20T23:59:59.000Z

343

Protecting consumer privacy from electric load monitoring  

Science Conference Proceedings (OSTI)

The smart grid introduces concerns for the loss of consumer privacy; recently deployed smart meters retain and distribute highly accurate profiles of home energy use. These profiles can be mined by Non Intrusive Load Monitors (NILMs) to expose much of ... Keywords: load monitor, privacy, smart meter

Stephen McLaughlin; Patrick McDaniel; William Aiello

2011-10-01T23:59:59.000Z

344

Quantifying the effectiveness of load balance algorithms  

Science Conference Proceedings (OSTI)

Load balance is critical for performance in large parallel applications. An imbalance on today's fastest supercomputers can force hundreds of thousands of cores to idle, and on future exascale machines this cost will increase by over a factor of a thousand. ... Keywords: framework, load balance, modeling, performance, simulation

Olga Pearce; Todd Gamblin; Bronis R. de Supinski; Martin Schulz; Nancy M. Amato

2012-06-01T23:59:59.000Z

345

Household type load's effects on photovoltaic systems  

Science Conference Proceedings (OSTI)

The solar energy is one of the most important energy sources available because, besides the fact that it is not polluting the environment and it helps to the reduction of green house effect, it is free of charge and it can be easily converted to other ... Keywords: A.C. loads, D.C. loads, compact fluorescent lamp, photovoltaic system, power LED

Nazmi Ekren; Nevzat Onat; Safak Saglam

2008-12-01T23:59:59.000Z

346

Load Modeling Using a Measurement Based Approach  

Science Conference Proceedings (OSTI)

This report summarizes the work performed in the second phase of a multi-year collaborative load modeling research program that was initiated in 2004. The measurement based approach described in this report will help utilities to develop representative load models using suitable measurement data.

2007-12-17T23:59:59.000Z

347

Apparatus for loading a band saw blade  

DOE Patents (OSTI)

A band saw blade is loaded between pairs of guide wheels upon tensioning the blade by guiding the blade between pairs of spaced guide plates which define converging slots that converge toward the guide wheels. The approach is particularly useful in loading blades on underwater band saw machines used to cut radioactive materials.

Reeves, Steven R. (49 Williams Ave., West Valley, NY 14171)

1990-01-01T23:59:59.000Z

348

The Promise of Load Balancing the Parameterization of Moist Convection Using a Model Data Load Index  

Science Conference Proceedings (OSTI)

The parameterization of physical processes in atmospheric general circulation models contributes to load imbalances among individual processors of message-passing distributed-multiprocessor systems. Load imbalances increase the overall time to ...

S. P. Muszala; D. A. Connors; J. J. Hack; G. Alaghband

2006-04-01T23:59:59.000Z

349

Estimating Demand Response Load Impacts: Evaluation of Baseline Load Models for Non-  

E-Print Network (OSTI)

, and the Office of Electricity Delivery and Energy Reliability, Permitting, Siting and Analysis of the ULBNL-63728 Estimating Demand Response Load Impacts: Evaluation of Baseline Load Models for Non .............................................................................................................. 9 4. Baseline Profile (BLP) Models

350

Independent review of estimated load reductions for PJM's small customer load response pilot project  

E-Print Network (OSTI)

Abbreviations ADDF ALM AMR CSP DOE DR ELRP ETS EWH FERC HVa Curtailment Service Provider (CSP) at PJM’s request. LBNLof load control tests. The CSP collected hourly load data

Heffner, G.; Moezzi, M.; Goldman, C.

2004-01-01T23:59:59.000Z

351

Combi Systems for Low Load homes  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

text styles text styles Combi Systems for Low Load Homes Center for Energy and Environment, NorthernSTAR, Ben Schoenbauer * Low load homes are more common than ever. * Typical space heating and DHW equipment have capacities larger than necessary * A single heating plant could provide high efficiency heat at lower costs, increased durability and improved combustion safety Context Technical Approach * A condensing water heater and hydronic air handler will used to provide space and water heating loads in almost 300 weatherized homes. * System specifications, sizing, and installation optimization guidelines were all developed. * Contractor capability was developed in MN market, but may not be developed in all local. 4 Recommended Guidance * Determine peak load on system: - Space heating design load (ie 40,000 Btu/hr)

352

Plug Load Energy Analysis: The Role of Plug Loads in LEED Certification  

E-Print Network (OSTI)

benchmark and is bound to change as the proportion of plug load energy use grows in commercial buildings.

Fuertes, Gwen; Schiavon, Stefano

2013-01-01T23:59:59.000Z

353

Combustion Impacts of Flexible Operation: Low Load, Load Following, and Increased Staging Impact on Boiler Tubes  

Science Conference Proceedings (OSTI)

Over the past few years, coal-fired generating units have changed from stable base load operation to flexible operation, including periods of prolonged low-load operation. These changes in operation can have various adverse effects on all plant equipment, particularly in older units and may impact their ability to operate without tube failures due to elevated levels of fireside corrosion and circumferential cracking. This report discusses the combustion-related impacts of low-load, load-following, ...

2013-12-23T23:59:59.000Z

354

Using Utility Load Data to Estimate Demand for Space Cooling and Potential for Shiftable Loads  

SciTech Connect

This paper describes a simple method to estimate hourly cooling demand from historical utility load data. It compares total hourly demand to demand on cool days and compares these estimates of total cooling demand to previous regional and national estimates. Load profiles generated from this method may be used to estimate the potential for aggregated demand response or load shifting via cold storage.

Denholm, P.; Ong, S.; Booten, C.

2012-05-01T23:59:59.000Z

355

An Analysis of Load Balancing Technology - Comparing LSF with other Load Balancing Software Packages  

E-Print Network (OSTI)

This paper examines what the load balancing needs of organizations are today, the solution LSF (Load Sharing Facility) provides for them, and how other currently available load balancing products compare to LSF. Jean Suplick (suplick@cxsoft.convex.com) CXSOFT Richardson, Texas January 1994 Why clusters?

Jean Suplick

1994-01-01T23:59:59.000Z

356

Variability of Load and Net Load in Case of Large Scale Distributed Wind Power  

Science Conference Proceedings (OSTI)

Large scale wind power production and its variability is one of the major inputs to wind integration studies. This paper analyses measured data from large scale wind power production. Comparisons of variability are made across several variables: time scale (10-60 minute ramp rates), number of wind farms, and simulated vs. modeled data. Ramp rates for Wind power production, Load (total system load) and Net load (load minus wind power production) demonstrate how wind power increases the net load variability. Wind power will also change the timing of daily ramps.

Holttinen, H.; Kiviluoma, J.; Estanqueiro, A.; Gomez-Lazaro, E.; Rawn, B.; Dobschinski, J.; Meibom, P.; Lannoye, E.; Aigner, T.; Wan, Y. H.; Milligan, M.

2011-01-01T23:59:59.000Z

357

Dehumidification and cooling loads from ventilation air  

SciTech Connect

The importance of controlling humidity in buildings is cause for concern, in part, because of indoor air quality problems associated with excess moisture in air-conditioning systems. But more universally, the need for ventilation air has forced HVAC equipment (originally optimized for high efficiency in removing sensible heat loads) to remove high moisture loads. To assist cooling equipment and meet the challenge of larger ventilation loads, several technologies have succeeded in commercial buildings. Newer technologies such as subcool/reheat and heat pipe reheat show promise. These increase latent capacity of cooling-based systems by reducing their sensible capacity. Also, desiccant wheels have traditionally provided deeper-drying capacity by using thermal energy in place of electrical power to remove the latent load. Regardless of what mix of technologies is best for a particular application, there is a need for a more effective way of thinking about the cooling loads created by ventilation air. It is clear from the literature that all-too-frequently, HVAC systems do not perform well unless the ventilation air loads have been effectively addressed at the original design stage. This article proposes an engineering shorthand, an annual load index for ventilation air. This index will aid in the complex process of improving the ability of HVAC systems to deal efficiently with the amount of fresh air the industry has deemed useful for maintaining comfort in buildings. Examination of typical behavior of weather shows that latent loads usually exceed sensible loads in ventilation air by at least 3:1 and often as much as 8:1. A designer can use the engineering shorthand indexes presented to quickly assess the importance of this fact for a given system design. To size those components after they are selected, the designer can refer to Chapter 24 of the 1997 ASHRAE Handbook--Fundamentals, which includes separate values for peak moisture and peak temperature.

Harriman, L.G. III [Mason-Grant, Portsmouth, NH (United States); Plager, D. [Quantitative Decision Support, Portsmouth, NH (United States); Kosar, D. [Gas Research Inst., Chicago, IL (United States)

1997-11-01T23:59:59.000Z

358

Automatic Detection of Unsafe Component Loadings  

E-Print Network (OSTI)

Dynamic loading of software components (e.g., libraries or modules) is a widely used mechanism for improved system modularity and flexibility. Correct component resolution is critical for reliable and secure software execution, however, programming mistakes may lead to unintended or even malicious components to be resolved and loaded. In particular, dynamic loading can be hijacked by placing an arbitrary file with the specified name in a directory searched before resolving the target component. Although this issue has been known for quite some time, it was not considered serious because exploiting it requires access to the local file system on the vulnerable host. Recently such vulnerabilities started to receive considerable attention as their remote exploitation became realistic; it is now important to detect and fix these vulnerabilities. In this paper, we present the first automated technique to detect vulnerable and unsafe dynamic component loadings. Our analysis has two phases: 1) apply dynamic binary instrumentation to collect runtime information on component loading (online phase); and 2) analyze the collected information to detect vulnerable component loadings (offline phase). For evaluation, we implemented our technique to detect vulnerable and unsafe DLL loadings in popular Microsoft Windows software. Our results show that unsafe DLL loading is prevalent and can lead to serious security threats. Our tool detected more than 1,700 unsafe DLL loadings in 28 widely used software and discovered serious attack vectors for remote code execution. Microsoft has opened a Microsoft Security Response Center (MSRC) case on our reported issues and is working with us and other affected software vendors to develop necessary patches.

Taeho Kwon; Zhendong Su

2010-01-01T23:59:59.000Z

359

Load Data Analysis and PowerShape Training: Strategic Load Research and Advanced Topics in Load Profiling for Settlements  

Science Conference Proceedings (OSTI)

Load shapes, representing usage patterns in the electric and gas industry, are a key factor in energy company operations and management. In the emerging restructured energy market, retail energy suppliers market energy to final customers and must arrange for electricity generation or gas delivery to meet their customers' needs. EPRI and Primen sponsored a workshop in September 2000 that addressed a range of issues associated with load shapes, including modeling, profiling for retail market settlement, re...

2000-12-20T23:59:59.000Z

360

Space cooling demands from office plug loads  

Science Conference Proceedings (OSTI)

Undersizing space cooling systems for office buildings can result in uncomfortable and angry tenants on peak cooling days. However, oversizing wastes money because more capacity is installed than is needed, and oversized systems have a lower energy efficiency which makes operating costs higher than necessary. Oversizing can adversely affect comfort as well, because oversized systems may provide poor humidity control and large temperature variations. Correct system sizing requires estimating building heat loads accurately. This paper discusses the heat load generated by the plug load, which includes any electrical equipment that is plugged into outlets.

Komor, P.

1997-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "load serving entity" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Definition: Base Load | Open Energy Information  

Open Energy Info (EERE)

Load Load Jump to: navigation, search Dictionary.png Base Load The minimum amount of electric power delivered or required over a given period at a constant rate.[1] View on Wikipedia Wikipedia Definition Baseload (also base load, or baseload demand) is the minimum amount of power that a utility or distribution company must make available to its customers, or the amount of power required to meet minimum demands based on reasonable expectations of customer requirements. Baseload values typically vary from hour to hour in most commercial and industrial areas. Related Terms electricity generation, power, smart grid References ↑ Glossary of Terms Used in Reliability Standards An in Like Like You like this.Sign Up to see what your friends like. line Glossary Definition Retrieved from

362

Modeling and control of thermostatically controlled loads  

SciTech Connect

As the penetration of intermittent energy sources grows substantially, loads will be required to play an increasingly important role in compensating the fast time-scale fluctuations in generated power. Recent numerical modeling of thermostatically controlled loads (TCLs) has demonstrated that such load following is feasible, but analytical models that satisfactorily quantify the aggregate power consumption of a group of TCLs are desired to enable controller design. We develop such a model for the aggregate power response of a homogeneous population of TCLs to uniform variation of all TCL setpoints. A linearized model of the response is derived, and a linear quadratic regulator (LQR) has been designed. Using the TCL setpoint as the control input, the LQR enables aggregate power to track reference signals that exhibit step, ramp and sinusoidal variations. Although much of the work assumes a homogeneous population of TCLs with deterministic dynamics, we also propose a method for probing the dynamics of systems where load characteristics are not well known.

Backhaus, Scott N [Los Alamos National Laboratory; Sinitsyn, Nikolai [Los Alamos National Laboratory; Kundu, S. [UNIV OF MICHIGAN; Hiskens, I. [UNIV OF MICHIGAN

2011-01-04T23:59:59.000Z

363

Impact of load type on microgrid stability  

E-Print Network (OSTI)

Microgrids show great promise as a means of integrating distributed generation sources into the public grid distribution system. In order to provide uninterrupted,high quality power to local loads, microgrids must have the ...

Monnin, Jared P

2012-01-01T23:59:59.000Z

364

High density load bearing insulation peg  

DOE Patents (OSTI)

A high density peg is disclosed which can support a large load and exhibits excellent thermal resistance produced by a method wherein the peg is made in compliance with specified conditions of time, temperature and pressure. 4 figs.

Nowobilski, J.J.; Owens, W.J.

1985-01-29T23:59:59.000Z

365

Passive load control for large wind turbines.  

DOE Green Energy (OSTI)

Wind energy research activities at Sandia National Laboratories focus on developing large rotors that are lighter and more cost-effective than those designed with current technologies. Because gravity scales as the cube of the blade length, gravity loads become a constraining design factor for very large blades. Efforts to passively reduce turbulent loading has shown significant potential to reduce blade weight and capture more energy. Research in passive load reduction for wind turbines began at Sandia in the late 1990's and has moved from analytical studies to blade applications. This paper discusses the test results of two Sandia prototype research blades that incorporate load reduction techniques. The TX-100 is a 9-m long blade that induces bend-twist coupling with the use of off-axis carbon in the skin. The STAR blade is a 27-m long blade that induces bend-twist coupling by sweeping the blade in a geometric fashion.

Ashwill, Thomas D.

2010-05-01T23:59:59.000Z

366

S-Band Loads for SLAC Linac  

SciTech Connect

The S-Band loads on the current SLAC linac RF system were designed, in some cases, 40+ years ago to terminate 2-3 MW peak power into a thin layer of coated Kanthal material as the high power absorber [1]. The technology of the load design was based on a flame-sprayed Kanthal wire method onto a base material. During SLAC linac upgrades, the 24 MW peak klystrons were replaced by 5045 klystrons with 65+ MW peak output power. Additionally, SLED cavities were introduced and as a result, the peak power in the current RF setup has increased up to 240 MW peak. The problem of reliable RF peak power termination and RF load lifetime required a careful study and adequate solution. Results of our studies and three designs of S-Band RF load for the present SLAC RF linac system is discussed. These designs are based on the use of low conductivity materials.

Krasnykh, A.; Decker, F.-J.; /SLAC; LeClair, R.; /INTA Technologies, Santa Clara

2012-08-28T23:59:59.000Z

367

High density load bearing insulation peg  

DOE Patents (OSTI)

A high density peg which can support a large load and exhibits excellent thermal resistance produced by a method wherein the peg is made in compliance with specified conditions of time, temperature and pressure.

Nowobilski, Jeffert J. (Orchard Park, NY); Owens, William J. (Kenmore, NY)

1985-01-01T23:59:59.000Z

368

Peak Load Shifting by Thermal Energy Storage  

Science Conference Proceedings (OSTI)

This technical update from the Electric Power Research Institute (EPRI) reviews the technology of storing energy in hot water and explores the potential for implementing this form of thermal energy storagethrough means of smart electric water heatersas a way to shift peak load on the electric grid. The report presents conceptual background, discusses strategies for peak load shifting and demand response, documents a series of laboratory tests conducted on a representative model of smart water heater, and...

2011-12-14T23:59:59.000Z

369

Gearbox Reliability Collaborative (GRC) Description and Loading  

SciTech Connect

This document describes simulated turbine load cases in accordance to the IEC 61400-1 Ed.3 standard, which is representative of the typical wind turbine design process. The information presented herein is intended to provide a broad understanding of the gearbox reliability collaborative 750kW drivetrain and turbine configuration. In addition, fatigue and ultimate strength drivetrain loads resulting from simulations are presented. This information provides the bases for the analytical work of the gearbox reliability collaborative effort.

Oyague, F.

2011-11-01T23:59:59.000Z

370

URANIUM AND PLUTONIUM LOADING ONTO MONOSODIUM TITANATE MST IN TANK 50H  

SciTech Connect

A possible disposition pathway for the residue from the abandoned In-Tank Precipitation (ITP) sends the material from Tank 48H in increments to Saltstone via aggregation in Tank 50H. After entering Tank 50H, the amount of fissile material sorbed on MST may increase as a result of contacting waste solutions with dissolved uranium and plutonium. SRNL recommends that nuclear criticality safety evaluations use uranium and plutonium loadings onto MST of 14.0 {+-} 1.04 weight percent (wt %) for uranium and 2.79 {+-} 0.197 wt % for plutonium given the assumed streams defined in this report. These values derive from recently measured for conditions relevant to the Actinide Removal Process (ARP) and serve as conservative upper bounds for uranium and plutonium loadings during the proposed transfers of MST from Tank 48H into Tank 50H.

Hobbs, D

2006-08-31T23:59:59.000Z

371

Load apparatus and method for bolt-loaded compact tension test specimen  

DOE Patents (OSTI)

A bolt-loaded compact tension test specimen load apparatus includes: a) a body having first and second opposing longitudinal ends, the first end comprising an externally threaded portion sized to be threadedly received within the test specimen threaded opening; b) a longitudinal loading rod having first and second opposing longitudinal ends, the loading rod being slidably received in a longitudinal direction within the body internally through the externally threaded portion and slidably extending longitudinally outward of the body first longitudinal end; c) a force sensitive transducer slidably received within the body and positioned to engage relative to the loading rod second longitudinal end; and d) a loading bolt threadedly received relative to the body, the loading bolt having a bearing end surface and being positioned to bear against the transducer to forcibly sandwich the transducer between the loading bolt and loading rod. Also disclosed is a method of in situ determining applied force during crack propagation in a bolt-loaded compact tension test specimen.

Buescher, Jr., Brent J. (Idaho Falls, ID); Lloyd, W. Randolph (Idaho Falls, ID); Ward, Michael B. (Idaho Falls, ID); Epstein, Jonathan S. (Idaho Falls, ID)

1997-01-01T23:59:59.000Z

372

Review: Stability of nonlinear masonry members under combined load  

Science Conference Proceedings (OSTI)

Under examination is the post buckling of unreinforced load-bearing masonry walls or piers subject to a combined load consisting of a uniformly distributed axial load and a concentrated eccentric load at the top end. Fixed free-ended prismatic columns ... Keywords: Brick walls, Combined load, Instability, Masonry, No-tension material, Nonlinear constitutive law

Igino Mura

2008-08-01T23:59:59.000Z

373

Conditional model of peak and minimum loads and the load duration curve for electricity  

SciTech Connect

This report presents a model that extends the traditional model of electricity demand to account for intra-period load variation, the kind of variation that is important for evaluating marginal-cost-reflecting price structures. The time-of-day rate is one such price structure. The traditional model of electricity demand explains inter-period demand variation. It says nothing about load variation. The report explains how a model that integrates with previous studies of electricity demand might be formulated. It specifies two concrete models within this framework and estimates them for a number of different utility companies. The model's within-sample-period performance in predicting peak loads is presented for one version of the model extension along with estimations for other variations. In addition a number of plots of actual load distributions, a summation of load variation information, against the actual load distributions, are presented and used to evaluate the performance of specific models.

Trimble, J.L.; Stallings, D.E.; Thomas, B.

1980-05-01T23:59:59.000Z

374

Indoor Air Quality Impacts of a Peak Load Shedding Strategy for a Large  

NLE Websites -- All DOE Office Websites (Extended Search)

Indoor Air Quality Impacts of a Peak Load Shedding Strategy for a Large Indoor Air Quality Impacts of a Peak Load Shedding Strategy for a Large Retail Building Title Indoor Air Quality Impacts of a Peak Load Shedding Strategy for a Large Retail Building Publication Type Report LBNL Report Number LBNL-59293 Year of Publication 2006 Authors Hotchi, Toshifumi, Alfred T. Hodgson, and William J. Fisk Keywords market sectors, technologies Abstract Mock Critical Peak Pricing (CPP) events were implemented in a Target retail store in the San Francisco Bay Area by shutting down some of the building's packaged rooftop air-handling units (RTUs). Measurements were made to determine how this load shedding strategy would affect the outdoor air ventilation rate and the concentrations of volatile organic compounds (VOCs) in the sales area. Ventilation rates prior to and during load shedding were measured by tracer gas decay on two days. Samples for individual VOCs, including formaldehyde and acetaldehyde, were collected from several RTUs in the morning prior to load shedding and in the late afternoon. Shutting down a portion (three of 11 and five of 12, or 27 and 42%) of the RTUs serving the sales area resulted in about a 30% reduction in ventilation, producing values of 0.50-0.65 air changes per hour. VOCs with the highest concentrations (>10 μg/m3) in the sales area included formaldehyde, 2-butoxyethanol, toluene and decamethylcyclopentasiloxane. Substantial differences in concentrations were observed among RTUs. Concentrations of most VOCs increased during a single mock CPP event, and the median increase was somewhat higher than the fractional decrease in the ventilation rate. There are few guidelines for evaluating indoor VOC concentrations. For formaldehyde, maximum concentrations measured in the store during the event were below guidelines intended to protect the general public from acute health risks.

375

Indoor Air Quality Impacts of a Peak Load Shedding Strategy for a Large  

NLE Websites -- All DOE Office Websites (Extended Search)

Indoor Air Quality Impacts of a Peak Load Shedding Strategy for a Large Indoor Air Quality Impacts of a Peak Load Shedding Strategy for a Large Retail Building Title Indoor Air Quality Impacts of a Peak Load Shedding Strategy for a Large Retail Building Publication Type Report Year of Publication 2006 Authors Hotchi, Toshifumi, Alfred T. Hodgson, and William J. Fisk Publisher Lawrence Berkeley National Laboratory Abstract Mock Critical Peak Pricing (CPP) events were implemented in a Target retail store in the San Francisco Bay Area by shutting down some of the building's packaged rooftop air-handling units (RTUs). Measurements were made to determine how this load shedding strategy would affect the outdoor air ventilation rate and the concentrations of volatile organic compounds (VOCs) in the sales area. Ventilation rates prior to and during load shedding were measured by tracer gas decay on two days. Samples for individual VOCs, including formaldehyde and acetaldehyde, were collected from several RTUs in the morning prior to load shedding and in the late afternoon. Shutting down a portion (three of 11 and five of 12, or 27 and 42%) of the RTUs serving the sales area resulted in about a 30% reduction in ventilation, producing values of 0.50-0.65 air changes per hour. VOCs with the highest concentrations (>10 μg/m3) in the sales area included formaldehyde, 2-butoxyethanol, toluene and decamethylcyclopentasiloxane. Substantial differences in concentrations were observed among RTUs. Concentrations of most VOCs increased during a single mock CPP event, and the median increase was somewhat higher than the fractional decrease in the ventilation rate. There are few guidelines for evaluating indoor VOC concentrations. For formaldehyde, maximum concentrations measured in the store during the event were below guidelines intended to protect the general public from acute health risks

376

Harmonic approaches to non-intrusive load diagnostics  

E-Print Network (OSTI)

The Non-Intrusive Load Monitor (NILM) is a system that monitors, records and processes voltage and current measurements to establish the operating characteristics of individual loads on a load center from a single aggregate ...

Fuller, Ashley E. (Ashley Eliot)

2008-01-01T23:59:59.000Z

377

Building Energy Software Tools Directory: HVAC Residential Load...  

NLE Websites -- All DOE Office Websites (Extended Search)

HVAC Residential Load Calcs HD for the iPad Carmel Software logo HVAC Residential Load Calcs HD is a comprehensive HVAC heating and cooling load calculation application for the...

378

IMPROVEMENTS TO THE RADIANT TIME SERIES METHOD COOLING LOAD CALCULATION  

E-Print Network (OSTI)

IMPROVEMENTS TO THE RADIANT TIME SERIES METHOD COOLING LOAD CALCULATION PROCEDURE By BEREKET TO THE RADIANT TIME SERIES METHOD COOLING LOAD CALCULATION PROCEDURE Dissertation Approved: Dr. Jeffrey D- Original RTSM.......................................................153 4.4.1 RTSM Peak Design Cooling Load

379

Direct versus Facility Centric Load Control for Automated Demand Response  

E-Print Network (OSTI)

actions to influence load profiles of their customers atISO needs to influence the load profile of a Facility arebe a specific target load profile to be achieved while in

Piette, Mary Ann

2010-01-01T23:59:59.000Z

380

Property Models for High Waste Loaded Hanford HLW Glasses  

High Waste Loading Was Shown for Selected Wastes Examples of the high loaded glasses Al 2O 3 loadings in the 24-26 wt% range compared to <15% for a

Note: This page contains sample records for the topic "load serving entity" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

How and why distribution loads vary  

SciTech Connect

Because the maximum-use rates of gas customers having differing appliance combinations do not coincide, a distribution system's peak-hour flow rate depends on the relative proportions of the load contributed by the appliances of all the different types of residential, commercial, and industrial customers. The maximum load on Central Hudson's distribution system coincides with the maximum hourly gas flow rate for all residential space-heating purposes; however, Central Hudson analyzes the peak-hour load of its commercial and industrial customers individually. The gas-system sendout presented as a sendout-duration curve is a convenient way to show how these various loads determine gas requirements and to compare the economics of alternative supply methods. The sendout-duration curve consists of long-term weather data plotted against time intervals of 1-365 days. If the threshold temperature and the heating load per degree-day are known, the curve allows the calculation of both normal and design annual peakshaving quantities.

Haber, D.P.

1980-01-01T23:59:59.000Z

382

Status of load management storage demonstrations  

DOE Green Energy (OSTI)

DOE is funding a nationwide demonstration of electric load management through the use of utility-controlled, customer-side thermal energy storage for residential space conditioning. The general concept of the projects was developed with the assistance of a broadly based working group drawn from the utility industry. This paper presents the current status of these demonstrations. Ten demonstrations are underway - five heat storage and five cool storage - using between 30 and 50 near-commercial thermal storage devices. The installations and experimental program are designed to: (1) collect reliable load research data for assessing the impact on the utility system; (2) delineate and solve installation problems; (3) establish maintainability; (4) illuminate customer and utility acceptance; and (5) generate cost data. The results obtained are expected to assist utilities in making local load-management decisions, to assist DOE in establishing priorities for R and D efforts in load management, and to provide objective information related to the electric system impact, energy conservation, and cost-effectiveness of this form of load management.

Long, H M; Mohre, D L

1979-01-01T23:59:59.000Z

383

A practical approach for electricity load forecasting  

E-Print Network (OSTI)

Abstract—This paper is a continuation of our daily energy peak load forecasting approach using our modified network which is part of the recurrent networks family and is called feed forward and feed back multi context artificial neural network (FFFB-MCANN). The inputs to the network were exogenous variables such as the previous and current change in the weather components, the previous and current status of the day and endogenous variables such as the past change in the loads. Endogenous variable such as the current change in the loads were used on the network output. Experiment shows that using endogenous and exogenous variables as inputs to the FFFB-MCANN rather than either exogenous or endogenous variables as inputs to the same network produces better results. Experiments show that using the change in variables such as weather components and the change in the past load as inputs to the FFFB-MCANN rather than the absolute values for the weather components and past load as inputs to the same network has a dramatic impact and produce better accuracy.

T. Rashid; T. Kechadi

2005-01-01T23:59:59.000Z

384

Wall Street: Money Never Sleeps (2010) In 2001, Gordon Gekko (Michael Douglas) is released from prison after serving eight years for  

E-Print Network (OSTI)

prison after serving eight years for insider trading and securities fraud. Seven years later, Gekko of an African oil field owned by Churchill Schwartz. The company loses $120 million, and Bretton offers Moore

Schenato, Luca

385

Load cell having strain gauges of arbitrary location  

DOE Patents (OSTI)

A load cell utilizes a plurality of strain gauges mounted upon the load cell body such that there are six independent load-strain relations. Load is determined by applying the inverse of a load-strain sensitivity matrix to a measured strain vector. The sensitivity matrix is determined by performing a multivariate regression technique on a set of known loads correlated to the resulting strains. Temperature compensation is achieved by configuring the strain gauges as co-located orthogonal pairs.

Spletzer, Barry (Albuquerque, NM)

2007-03-13T23:59:59.000Z

386

AMENDED AND RESTATED DELEGATION AGREEMENT BETWEEN NORTH AMERICAN ELECTRIC RELIABILITY CORPORATION AND TEXAS RELIABILITY ENTITY, INC. AMENDED AND RESTATED DELEGATION AGREEMENT (“Agreement”) made  

E-Print Network (OSTI)

an organization certified by the Federal Energy Regulatory Commission (“Commission”) pursuant to Section 215(c) of the Federal Power Act to establish and enforce Reliability Standards for the Bulk-Power System, and Texas Reliability Entity, Inc. (“Texas RE”) , an organization established to develop and enforce Reliability Standards within the geographic boundaries identified on Exhibit A to this Agreement, and for other purposes. NERC and Texas RE may be individually referred to herein as “Party ” or collectively as “Parties.” WITNESSETH WHEREAS, Subtitle A of the Electricity Modernization Act of 2005 added Section 215 to the Federal Power Act (16 U.S.C. § 824n) (hereafter “the Act”), which, among other things, provides for the establishment of an electric reliability organization (“ERO”) to develop and enforce Reliability Standards applicable to all owners, operators, and users of the Bulk-Power System; WHEREAS, the Commission has adopted regulations for the implementation of the Act, which are set forth at Chapter I, Title 18, Code of Federal Regulations, Part 39 (the “ERO Regulations”); WHEREAS, the Commission has certified NERC as the ERO that will, in accordance with the Act, establish and enforce Reliability Standards for the Bulk-Power System, subject to certain delegation provisions described below; WHEREAS, the Act recognizes the international interdependency of electric reliability within North America and envisions the ERO and such applicable Regional Entities as international organizations;

unknown authors

2011-01-01T23:59:59.000Z

387

A comparison of measured wind park load histories with the WISPER and WISPERX load spectra  

DOE Green Energy (OSTI)

The blade-loading histories from two adjacent Micon 65/13 wind turbines are compared with the variable-amplitude test-loading histories known as the WISPER and WISPERX spectra. These standardized loading sequences were developed from blade flapwise load histories taken from nine different horizontal-axis wind turbines operating under a wide range of conditions in Europe. The subject turbines covered a broad spectrum of rotor diameters, materials, and operating environments. The final loading sequences were developed as a joint effort of thirteen different European organizations. The goal was to develop a meaningful loading standard for horizontal-axis wind turbine blades that represents common interaction effects seen in service. In 1990, NREL made extensive load measurements on two adjacent Micon 65/13 wind turbines in simultaneous operation in the very turbulent environment of a large wind park. Further, before and during the collection of the loads data, comprehensive measurements of the statistics of the turbulent environment were obtained at both the turbines under test and at two other locations within the park. The trend to larger but lighter wind turbine structures has made an understanding of the expected lifetime loading history of paramount importance. Experience in the US has shown that the turbulence-induced loads associated with multi-row wind parks in general are much more severe than for turbines operating individually or within widely spaced environments. Multi-row wind parks are much more common in the US than in Europe. In this paper we report on our results in applying the methodology utilized to develop the WISPER and WISPERX standardized loading sequences using the available data from the Micon turbines. While the intended purpose of the WISPER sequences were not to represent a specific operating environment, we believe the exercise is useful, especially when a turbine design is likely to be installed in a multi-row wind park.

Kelley, N.D.

1995-01-01T23:59:59.000Z

388

Comparison of Building Energy Modeling Programs: Building Loads  

NLE Websites -- All DOE Office Websites (Extended Search)

Comparison of Building Energy Modeling Programs: Building Loads Title Comparison of Building Energy Modeling Programs: Building Loads Publication Type Report LBNL Report Number...

389

The Effect of Daylighting Strategies on Building Cooling Loads...  

NLE Websites -- All DOE Office Websites (Extended Search)

The Effect of Daylighting Strategies on Building Cooling Loads and Overall Energy Performance Title The Effect of Daylighting Strategies on Building Cooling Loads and Overall...

390

Repository Reference Disposal Concepts and Thermal Load Management...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Repository Reference Disposal Concepts and Thermal Load Management Analysis Repository Reference Disposal Concepts and Thermal Load Management Analysis A disposal concept consists...

391

Definition: Dispersed Load By Substations | Open Energy Information  

Open Energy Info (EERE)

By Substations Jump to: navigation, search Dictionary.png Dispersed Load By Substations Substation load information configured to represent a system for power flow or system...

392

Methods and apparatus for reduction of asymmetric rotor loads in ...  

A method for reducing load and providing yaw alignment in a wind turbine includes measuring displacements or moments resulting from asymmetric loads on the wind turbine.

393

Building Energy Software Tools Directory: Prophet Load Profiler  

NLE Websites -- All DOE Office Websites (Extended Search)

Shots Keywords energy analysis, load profiling, cost comparison, energy budgeting, rate analysis, data collection, real-time monitoring, load shedding ValidationTesting NA...

394

Energetical factors in power systems with nonlinear loads  

Science Conference Proceedings (OSTI)

Based on the volt-ampere charac- teristic of the nonlinear load, an equivalent circuit, containing linear elements, can be determined. In this way, load-flow and.

395

Used Nuclear Fuel Loading and Structural Performance Under Normal...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Used Nuclear Fuel Loading and Structural Performance Under Normal Conditions of Transport - Modeling, Simulation and Experimental Integration RD&D Plan Used Nuclear Fuel Loading...

396

Definition: Direct Control Load Management | Open Energy Information  

Open Energy Info (EERE)

Control Load Management Jump to: navigation, search Dictionary.png Direct Control Load Management Demand-Side Management that is under the direct control of the system operator....

397

Definition: Circuit Peak Load Management | Open Energy Information  

Open Energy Info (EERE)

Circuit Peak Load Management Jump to: navigation, search Dictionary.png Circuit Peak Load Management An application utilizing sensors, information processors, communications, and...

398

Definition: Real-Time Load Transfer | Open Energy Information  

Open Energy Info (EERE)

Real-time load transfer is achieved through real-time feeder reconfiguration and optimization to relieve load on equipment, improve asset utilization, improve distribution...

399

Load Control for System Reliability and Measurement-Based Stability...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Load Control for System Reliability and Measurement-Based Stability Assessment Load Control for System Reliability and Measurement-Based Stability Assessment Research and develop...

400

Load attenuating passively adaptive wind turbine blade  

DOE Patents (OSTI)

A method and apparatus for improving wind turbine performance by alleviating loads and controlling the rotor. The invention employs the use of a passively adaptive blade that senses the wind velocity or rotational speed, and accordingly modifies its aerodynamic configuration. The invention exploits the load mitigation prospects of a blade that twists toward feather as it bends. The invention includes passively adaptive wind turbine rotors or blades with currently preferred power control features. The apparatus is a composite fiber horizontal axis wind-turbine blade, in which a substantial majority of fibers in the blade skin are inclined at angles of between 15 and 30 degrees to the axis of the blade, to produces passive adaptive aeroelastic tailoring (bend-twist coupling) to alleviate loading without unduly jeopardizing performance.

Veers, Paul S. (Albuquerque, NM); Lobitz, Donald W. (Albuquerque, NM)

2003-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "load serving entity" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Estimating Demand Response Load Impacts: Evaluation of Baseline Load Models for Non-Residential Buildings in California  

E-Print Network (OSTI)

This  baseline  load  profile  (BLP)  is  key  to to  as  the  baseline  load  profile  or  BLP  and  is  key actual  and  estimated  load  profiles  look,  Figure  1 

Coughlin, Katie; Piette, Mary Ann; Goldman, Charles; Kiliccote, Sila

2008-01-01T23:59:59.000Z

402

Matching equipment size to the cooling load  

SciTech Connect

This article presents a heat extraction rate analysis method, using ASHRAE algorithms that enables HVAC system designers to optimally size cooling equipment. The final stage of the cooling load calculation process determines the heat extraction rate required to achieve design conditions. Put another way, this stage determines the equipment capacity required to match the cooling load profile, and it does so in a manner that predicts the resulting space temperature profile, and it does so in a manner that predicts the resulting space temperature profile. It is a stage in the design process that, in practice, may not be given the attention it deserves.

Bloom, B. (Harvey Toub Engineering, Atlanta, GA (United States))

1993-10-01T23:59:59.000Z

403

Demand-Side Response from Industrial Loads  

Science Conference Proceedings (OSTI)

Through a research study funded by the Department of Energy, Smart Grid solutions company ENBALA Power Networks along with the Oak Ridge National Laboratory (ORNL) have geospatially quantified the potential flexibility within industrial loads to leverage their inherent process storage to help support the management of the electricity grid. The study found that there is an excess of 12 GW of demand-side load flexibility available in a select list of top industrial facilities in the United States. Future studies will expand on this quantity of flexibility as more in-depth analysis of different industries is conducted and demonstrations are completed.

Starke, Michael R [ORNL; Alkadi, Nasr E [ORNL; Letto, Daryl [Enbala Power Networks; Johnson, Brandon [University of Tennessee, Knoxville (UTK); Dowling, Kevin [University of Tennessee, Knoxville (UTK); George, Raoule [Enbala Power Networks; Khan, Saqib [University of Texas, Austin

2013-01-01T23:59:59.000Z

404

New method developed for LPG offshore loading  

SciTech Connect

An innovative concept for refrigerated LPG offshore loading has been developed by TOTAL and Enterprise D'Equipments Mecaniques at Hydrauliques. Known as CHAGAL, the system integrates with the catenary anchor leg mooring offshore loading system commonly used for crude oil. CHAGAL provides a suitable answer to short-term development schemes of LPG trade. It can be adapted for possible extrapolation to cryogenic temperatures of LNG and it opens a new way to the development of offshore liquefaction projects for which the offloading of production is still an unsolved key problem.

1985-10-01T23:59:59.000Z

405

LOADED WAVE GUIDES FOR LINEAR ACCELERATORS  

DOE Patents (OSTI)

A periodically loaded waveguide having substantially coaxially arranged elements which provide an axial field for the acceleration of electrons is described. Radiofrequency energy will flow in the space between the inner wall of an outer guide and the peripheries of equally spaced irises or washes arranged coaxially with each other and with the outer guide, where the loading due to the geometry of the irises is such as to reduce the phase velocity of the r-f energy flowing in the guide from a value greater than that of light to the velocity of light or less.

Walkinshaw, W.; Mullett, L.B.

1959-12-01T23:59:59.000Z

406

Exploring the feasibility of developing partnerships between Hispanic-serving organizations and the 4-H clubs in the state of Texas, in both urban and rural communities  

E-Print Network (OSTI)

The primary purpose of this study was to explore the phics. feasibility of developing partnerships between Hispanic-serving organizations and the 4-H club in both rural and urban areas in the state of Texas. The study also identified existing and non-existing Hispanic-serving organizations in the state of Texas, current relationships between Hispanic-service organizations and the 4-H program in the state of Texas, and benefits that can arise between these partnerships. The study was conducted during late spring and early summer, 1998. The target sample for this study was three hundred forty Hispanic-serving organizations in the state of Texas. There were eight Hispanic-serving organization directories that were used as the sampling frame for the study. The instrument used consisted of fifteen questions to determine familiarity of 4-H clubs, programs that focus on youth, youth and volunteer training, and current and potential collaboration between the 4-H program and Hispanic-serving organizations. The questionnaire also included two open-ended questions regarding benefits and alternative practices. l . The majority of the surveys came from urban areas where there were more Hispanic serving organizations to cater to the needs of the Hispanic population. The areas were Austin, Brownsville, Dallas, El Paso, Fort Worth, Houston, and San Antonio. 2. 75 percent of all organizations that responded to the survey were involved in service to youth in some form or fashion. The Hispanic-serving organizations that responded to the survey did not dedicate sufficient time (determined by the researcher) to the four main components of the 4-H program (leadership, youth training programs, public speaking, and community service). 4. Hispanic-serving organizations showed some familiarity with the 4-H program. However, 4-H is still seen as a club for the youth that live on a farm or rich. 5. Less than eve percent of Hispanic-serving organizations were currently working with the local 4-H program in their communities. Organizations are unsure as to what 4-H can provide to their community. 6. More than 50 percent of the Hispanic-serving organizations that responded to the survey were interested in developing a partnership with the 4-H club.

Rodriguez, Reyes Isaac

1998-01-01T23:59:59.000Z

407

Load relaxation studies of a metallic glass  

SciTech Connect

Experimental results of load relaxation studies of a commercial metallic glass as a function of temperature are reported. The data suggest that metallic glasses exhibit deformation behavior with flow laws similar to those governing plastic deformation in crystalline solids. The lack of appreciable work hardening in annealed material and the identification of an anelastic component are also indicated by the experimental observations. (GHT)

Hadnagy, T.D.; Krenisky, D.J.; Ast, D.G.; Li, C.Y.

1977-01-01T23:59:59.000Z

408

Flexible loads in future energy networks  

Science Conference Proceedings (OSTI)

We develop a vignette of an information-rich energy network with flexible and responsive electrical loads in the form of a domestic refrigerator augmented with a thermal storage system and a supply-following controller that responds to the availability ... Keywords: renewable, supply-following

Jay Taneja, Ken Lutz, David Culler

2013-01-01T23:59:59.000Z

409

Exercising flexible load contracts: Two simple strategies  

Science Conference Proceedings (OSTI)

A flexible load contract is a type of swing option where the holder has the right to receive a given quantity of electricity within a specified period, at a fixed maximum effect (delivery rate). The contract is flexible, in the sense that delivery (the ... Keywords: energy, exercise strategy, flexibility, swing option, uncertainty

Petter Bjerksund; Bjarte Myksvoll; Gunnar Stensland

2008-03-01T23:59:59.000Z

410

Incentivizing Advanced Load Scheduling in Smart Homes  

Science Conference Proceedings (OSTI)

In recent years, researchers have proposed numerous advanced load scheduling algorithms for smart homes with the goal of reducing the grid's peak power usage. In parallel, utilities have introduced variable rate pricing plans to incentivize residential ... Keywords: Battery, Electricity, Energy, Grid

Ye Xu, David Irwin, Prashant Shenoy

2013-11-01T23:59:59.000Z

411

Appliance Commitment for Household Load Scheduling  

Science Conference Proceedings (OSTI)

This paper presents a novel appliance commitment algorithm that schedules thermostatically-controlled household loads based on price and consumption forecasts considering users comfort settings to meet an optimization objective such as minimum payment or maximum comfort. The formulation of an appliance commitment problem was described in the paper using an electrical water heater load as an example. The thermal dynamics of heating and coasting of the water heater load was modeled by physical models; random hot water consumption was modeled with statistical methods. The models were used to predict the appliance operation over the scheduling time horizon. User comfort was transformed to a set of linear constraints. Then, a novel linear, sequential, optimization process was used to solve the appliance commitment problem. The simulation results demonstrate that the algorithm is fast, robust, and flexible. The algorithm can be used in home/building energy-management systems to help household owners or building managers to automatically create optimal load operation schedules based on different cost and comfort settings and compare cost/benefits among schedules.

Du, Pengwei; Lu, Ning

2011-06-30T23:59:59.000Z

412

Valve for fuel pin loading system  

DOE Patents (OSTI)

A cyclone valve surrounds a wall opening through which cladding is projected. An axial valve inlet surrounds the cladding. Air is drawn through the inlet by a cyclone stream within the valve. An inflatable seal is included to physically engage a fuel pin subassembly during loading of fuel pellets.

Christiansen, D.W.

1984-01-01T23:59:59.000Z

413

Lifeline-based global load balancing  

Science Conference Proceedings (OSTI)

On shared-memory systems, Cilk-style work-stealing has been used to effectively parallelize irregular task-graph based applications such as Unbalanced Tree Search (UTS). There are two main difficulties in extending this approach to distributed memory. ... Keywords: distributed work-stealing, global load balancing, uts, x10

Vijay A. Saraswat; Prabhanjan Kambadur; Sreedhar Kodali; David Grove; Sriram Krishnamoorthy

2011-02-01T23:59:59.000Z

414

Propagation in LHM slab loaded rectangular waveguide  

Science Conference Proceedings (OSTI)

The strange properties of Left - Handed Materials (LHM), whose permittivity and permeability are both negative, is briefly introduced. The electric- and magnetic-field components are given in rectangular waveguide loaded with LHM by use of field component ... Keywords: cutoff wavelength, dispersion equation, group velocity, left-handed materials, rectangular waveguide

Rui-Lian Li

2011-09-01T23:59:59.000Z

415

Economic load dispatch using improved harmony search  

Science Conference Proceedings (OSTI)

This paper presents the use of the improved harmony search method for solving economic load dispatch problems. The harmony search method mimics a jazz improvisation process by musicians in order to seek a fantastic state of harmony. To assess the searching ... Keywords: adaptive tabu search, economic dispatch, evolutionary programming, genetic algorithms, particle swarm optimization

T. Ratniyomchai; A. Oonsivilai; P. Pao-La-Or; T. Kulworawanichpong

2010-04-01T23:59:59.000Z

416

Load forecast and treatment of conservation  

E-Print Network (OSTI)

Load forecast and treatment of conservation July 28th 2010 Resource Adequacy Technical Committee conservation is implicitly incorporated in the short-term demand forecast? #12;3 Incorporating conservation in the short-term model Our short-term model is an econometric model which can not explicitly forecast

417

Valve for fuel pin loading system  

DOE Patents (OSTI)

A cyclone valve surrounds a wall opening through which cladding is projected. An axial valve inlet surrounds the cladding. Air is drawn through the inlet by a cyclone stream within the valve. An inflatable seal is included to physically engage a fuel pin subassembly during loading of fuel pellets.

Christiansen, David W. (Kennewick, WA)

1985-01-01T23:59:59.000Z

418

Independent review of estimated load reductions for PJM's small customer load response pilot project  

SciTech Connect

This study describes the results of a low-cost approach used to measure reported load reductions from a residential electric water heater (EWH) load control program operated as part of PJM Interconnection's Demand Response small customer pilot program. Lawrence Berkeley National Laboratory (LBNL) conducted this independent review of the engineering estimates for EWH load control reported by a Curtailment Service Provider (CSP) at PJM's request. LBNL employed low-cost measurement and verification (M&V) approaches that utilized existing interval metering equipment to monitor results for a series of load control tests. The CSP collected hourly load data for two substations and several hundred households over a six-week period in October and November 2003. During this time period, the CSP operated its electric water heater load control program during pre-specified test periods in the morning, afternoon and early evening. LBNL then analyzed substation and premise-level data from these tests in order to verify the diversified demand reductions claimed by the CSP for customers participating in the EWH load control program. We found that the observed load reductions for the premise-level data aggregated over all households in the two participating electric cooperatives were, respectively, 40 percent-60 percent less and 3 percent less-10 percent higher than the estimated diversified demand reduction values assumed by the CSP, depending on whether observed or normalized results are considered. We also analyzed sub-station level data and found that the observed load reductions during the test periods were significantly lower than expected, although confounding influences and operational problems signifiogram during pre-specified test periods in the morning, afternoon and early evening. LBNL then analyzed substation and premise-level data from these tests in order to verify the diversified demand reductions claimed by the CSP for customers participating in the EWH load control program. We found that the observed load reductions for the premise-level data aggregated over all households in the two participating electric cooperatives were, respectively, 40 percent-60 percent less and 3 percent less-10 percent higher than the estimated diversified demand reduction values assumed by the CSP, depending on whether observed or normalized results are considered. We also analyzed sub-station level data and found that the observed load reductions during the test periods were significantly lower than expected, although confounding influences and operational problems significantly limit our ability to differentiate between control-related and non-control related differences in substation-level load shape data. The usefulness and accuracy of the results were hampered by operational problems encountered during the measurement period as well as in sufficient number of load research grade interval meters at one cooperative. Given the larger sample size at one electric cooperative and more statistically-robust results, there is some basis to suggest that the Adjusted Diversified Demand Factor (ADDF) values used by the CSP somewhat over-state the actual load reductions. Given the results and limitations of the M&V approach as implemented, we suggest several options for PJM to consider: (1) require load aggregators participating in ISODR programs to utilize formal PURPA-compliant load research samples in their M&V plans, and (2) continue developing lower cost M&V approaches for mass market load control programs that incorporate suggested improvements described in this study.

Heffner, G.; Moezzi, M.; Goldman, C.

2004-06-01T23:59:59.000Z

419

Microarchitecture support for improving the performance of load target prediction  

Science Conference Proceedings (OSTI)

Presents a load target prediction scheme that mitigates the impact of load latency for modern microprocessors. The scheme uses a cache-like buffer to provide the base address, offset and operand size at the instruction fetching stage of a pipeline so ... Keywords: load target prediction, load-use stall, pipeline, speculative data access, superscalar procesor

Chung-Ho Chen; Akida Wu

1997-12-01T23:59:59.000Z

420

Load Balancing Content-Based Publish/Subscribe Systems  

Science Conference Proceedings (OSTI)

Distributed content-based publish/subscribe systems suffer from performance degradation and poor scalability caused by uneven load distributions typical in real-world applications. The reason for this shortcoming is the lack of a load balancing scheme. ... Keywords: PADRES, Publish/subscribe, ToPSS, content-based routing, load balancing, load estimation, offload algorithms, subscriber migration

Alex King Yeung Cheung; Hans-Arno Jacobsen

2010-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "load serving entity" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Vehicle Tank & Loading Rack Meters - 2013-04-22  

Science Conference Proceedings (OSTI)

Vehicle Tank & Loading Rack Meters. Purpose: ... Participants should bring a calculator to the training. Materials & Supplies: ...

2013-06-03T23:59:59.000Z

422

Classification and forecasting of load curves Nolwen Huet  

E-Print Network (OSTI)

on up to stabilisation of the clusters. Finally, the load profiles are predicted by covariance analysis of electricity customer uses. This load curve is only available for customers with automated meter readingClassification and forecasting of load curves Nolwen Huet Abstract The load curve, which gives

Cuesta, Juan Antonio

423

Reliability analysis of RC containment structures under combined loads  

SciTech Connect

This paper discusses a reliability analysis method and load combination design criteria for reinforced concrete containment structures under combined loads. The probability based reliability analysis method is briefly described. For load combination design criteria, derivations of the load factors for accidental pressure due to a design basis accident and safe shutdown earthquake (SSE) for three target limit state probabilities are presented.

Hwang, H.; Reich, M.; Kagami, S.

1984-01-01T23:59:59.000Z

424

The Temperature Sensitivity of the Residential Load and Commercial Building Load  

SciTech Connect

This paper presents a building modeling approach to quickly quantify climate change impacts on energy consumption, peak load, and load composition of residential and commercial buildings. This research focuses on addressing the impact of temperature changes on the building heating and cooling load in 10 major cities across the Western United States and Canada. A building simulation software are first used to quantify the hourly energy consumption of different building types by end-use and by vintage. Then, the temperature sensitivities are derived based on the climate data inputs.

Lu, Ning; Taylor, Zachary T.; Jiang, Wei; Correia, James; Leung, Lai R.; Wong, Pak C.

2009-07-26T23:59:59.000Z

425

Comparison of Zone Cooling Load for Radiant and All-Air Conditioning Systems  

E-Print Network (OSTI)

change the cooling load profile for the mechanical systems.and the resulting cooling load profile has been reported inimplications for cooling load profile and peak cooling load

Feng, Jingjuan; Schiavon, Stefano; Bauman, Fred

2012-01-01T23:59:59.000Z

426

LIST OF 361 ACORN COUNCIL AFFLILIATES, SUBSIDIARIES AN ALLIED ORGANIZATION (Note: The word ACORN is not always included in the associated entity name)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

361 ACORN COUNCIL AFFLILIATES, SUBSIDIARIES, AND ALLIED 361 ACORN COUNCIL AFFLILIATES, SUBSIDIARIES, AND ALLIED ORGANIZATIONS (Note: The word "ACORN" is not always included in the associated entity name) 1. Association of Community Organizations for Reform Now (ACORN) 2. ACORN National Office: Brooklyn, NY 3. ACORN Bronx, NY 4. ACORN Brooklyn, NY 5. ACORN Buffalo, NY 6. ACORN Hempstead, NY 7. ACORN HOUSING CORPORATION Brooklyn, NY 8. PROJECT VOTE Brooklyn, NY 9. MHANY Brooklyn, NY 10. ACORN National Office: Washington, D.C. 11. ACORN Washington, DC 12. ACORN HOUSING CORPORATION Washington, DC 13. ACORN Political 1334 G St, NW Suite B Washington, DC 20005 14. AISJ Washington, DC 15. ACORN National Office: Little Rock, AR 16. ACORN Pine Bluff, AR 17. ACORN Housing Corporation Little Rock, AR

427

Technical Update: Load Modeling in Power System Studies  

Science Conference Proceedings (OSTI)

EPRI has been engaged in load modeling research since the 1980’s. In the past, EPRI conducted significant research in the area of load modeling and worked together with the Western Electricity Coordinating Council (WECC) Load Modeling Task Force in the development of the new composite load model developed and currently to be deployed in WECC. This work included extensive testing of various load components, such as residential air-conditioners, in the EPRI laboratories in Knoxville, TN. In ...

2013-12-10T23:59:59.000Z

428

Conductor Wind Loading--Results of EPRI Field Validation Studies  

Science Conference Proceedings (OSTI)

A comprehensive evaluation of current wind load methods indicates that several factors can adversely affect the performance of wind load models. There are wide variations and biased values associated with some of the wind parameters, and inaccurate drag coefficient and air density values can influence the wind load models. Several modified approaches were tested to properly incorporate wind gusts and spatial effects in wind load calculations. The improvement in the wind load predictions made by some of t...

1995-05-12T23:59:59.000Z

429

Estimating Demand Response Load Impacts: Evaluation of Baseline Load Models for Non-Residential Buildings in California  

E-Print Network (OSTI)

energy  use  for  space  conditioning,  non? weather Physically,  space?conditioning  loads  are  affected  by 

Coughlin, Katie; Piette, Mary Ann; Goldman, Charles; Kiliccote, Sila

2008-01-01T23:59:59.000Z

430

Load-shape modeling in southeastern utility systems  

SciTech Connect

Load models are tools which have a wide range of application in the electric-utility industry. Some uses include monitoring load-management policies and helping with on-line commitment problems. The output from a load model can be placed in a suitable software environment where daily load curves are computed and displayed. Also, load models can be extended to perform forecasting functions. A weather sensitive load model that takes into account both weekdays and weekends on an hourly basis has been developed and applied to load shape modeling and short term forecasting on three southeastern electric utilities. A software package associated with the load modeling theory was developed and tested. This load-modeling program computes the daily load curve in terms of identifiable components. The program uses historical hourly load data to compute coefficients related to load components including base, growth, seasonal and weather. These coefficients can be used in a mathematical model to compute an estimate of the daily load curve with load values for each hour of the day. The load-modeling procedure described employs a linear least squares method for computing coefficients in the mathematical model.

Lebby, G.L.

1985-01-01T23:59:59.000Z

431

2012 CERTS LAAR Program Peer Review - Integration and Extension of Direct Load Management of Smart Loads - Anna Scaglioni, UC Davis  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Integration and Extension of Direct Integration and Extension of Direct Load Management of Smart Loads Anna Scaglione, UC Davis GRA: Mahnoosh Alizadeh Project objective  Invent methods to "store" load demand for * Real-time "generation following" * Integration of load reserves as dispatchable assets in the Energy Market  Architecture for virtual "reserves" (queues) of electrical load demand * Watts to Job mapping (analysis)  Captures digitally the service requirements - Equal service type = Equal queue * Job to Watts mapping (synthesis)  Allows to optimally schedule the load profile Major technical accomplishments  Centralized model: Digital Direct Load Scheduling (DDLS) - Year 1-Year 2

432

Decision matrix for liquid loading in gas wells for cost/benefit analyses of lifting options  

E-Print Network (OSTI)

Field-proven solutions already exist to reduce the loss of gas production when liquid loading begins to occur. However, the choice of remedial technique, its feasibility, and its cost, vary considerably depending on a field's location, size export route, and the individual operator's experience. The selection of the best remedial technique and the timeframe within which the remedial action is undertaken are critical to a project's profitability. Although there are literature reviews available regarding solutions to liquid loading problems in gas wells, a tool capable of helping an operator select the best remedial option for a specific field case still does not exist. This thesis proposes a newly developed decision matrix to screen the possible remedial options available to the operator. The matrix can not only provide a critical evaluation of potential solutions to the problem of liquid loading in gas wells vis-a?-vis the existing technical and economic constraints, but can also serve as a reference to operators for investment decisions and as a quick screening tool for the selection of production optimisation strategies. Under its current status of development, this new tool consists of a decision algorithm built around a decision tree. Unlike other data mining techniques, decision trees quickly allow for subdividing large initial datasets into successively smaller sets by a series of decision rules. The rules are based on information available in the public domain. The effectiveness of the matrix is now ready to be tested against real field datasets.

Park, Han-Young

2008-05-01T23:59:59.000Z

433

A new generation of load sharing algorithms: the semi-adaptive load sharing algorithm  

E-Print Network (OSTI)

Distributed systems have become a popular computing environment. Due to their high potentials in improving performance and resource sharing, the evolution and maturing of technologies such as networks and computer hardware, have led to more realizations of distributed computing capabilities. One of the key factors that impacts the system's performance is how load sharing is handled. Most of the work done in load sharing algorithms focused on either one of two approaches: the static approach, or the dynamic approach. Static load sharing is characterized with its simplicity and minimal overhead induced on the system when performing load distribution. This is attributed to the fact that their load sharing decisions do not require any information exchange between nodes. However, static algorithms are not capable of adapting to traffic changes. Hence, this will affect the distributed system adaptability and stability features against load alteration. The second approach in load sharing algorithums is the dynamic approach. In this approach, nodes base their sharing decisions on the knowledge of the status on other nodes. This knowledge enables nodes to make improved decisions when selecting a remote execution site. Therefore, these algorithms provide the distributed system with adaptability and stability. Nevertheless, information exchange between nodes has proven to be expensive. The problem lies in the communication and processing overheads which these algorithms impose on the system. This research work presents a Semi-Adaptive load sharing approach that attempts to lay a common ground between the dynamic and the static approaches. This approach provides the system with adaptability features at are supplied with tools to control the level of adaptability and information exchange in the system. It is argued that this approach is adaptable, scalable, stable, fault tolerant, and will generate low and controlled system overheads. Two implementations of the Semi-Adaptive approach are presented: The Controller Load Sharing Protocol (CLSP) and The Pool Load Sharing Protocol (PLSP). The study of CLSP and PLSP include simulating their performance under various conditions. The simulation include comparing the performance of these two protocols against two load sharing algorithms representing the static and dynamic families. Furthermore, the properties of CLSP and PLSP are investigated. Finally, based on the study and analysis of both protocols, the research work proposes possible areas of improvement in the final conclusion.

Morsy, Hazem Kamal

1997-01-01T23:59:59.000Z

434

Calculations of slurry pump jet impingement loads  

SciTech Connect

This paper presents a methodology to calculate the impingement load in the region of a submerged turbulent jet where a potential core exits and the jet is not fully developed. The profile of the jet flow velocities is represented by a piece-wise linear function which satisfies the conservation of momentum flux of the jet flow. The adequacy of the of the predicted jet expansion is further verified by considering the continuity of the jet flow from the region of potential core to the fully developed region. The jet impingement load can be calculated either as a direct impingement force or a drag force using the jet velocity field determined by the methodology presented.

Wu, T.T.

1996-03-04T23:59:59.000Z

435

Two-phase jet loads. [PWR  

Science Conference Proceedings (OSTI)

Two-phase jets are currently being studied to improve engineering models for the prediction of loads on pipes and structures during LOCAs. Multi-dimensional computer codes such as BEACON/MOD2, CSQ, and TRAC-P1A are being employed to predict flow characteristics and flow-structure loading. Our ultimate goal is to develop a new approximate engineering model which is superior to the F.J. Moody design model. Computer results are compared with data obtained from foreign sources, and a technique for using the TRAC-P1A vessel component as a containment model is presented. In general, good agreement with the data is obtained for saturated stagnation conditions; however, difficulties are encountered for subcooled stagnation conditions, possibly due to nucleation delay and non-equilibrium effects.

Tomasko, D.

1980-01-01T23:59:59.000Z

436

NREL: Vehicle Ancillary Loads Reduction - Integrated Modeling  

NLE Websites -- All DOE Office Websites (Extended Search)

Integrated Modeling Integrated Modeling NREL's Vehicle Ancillary Loads Reduction (VALR) team predicts the impact of advanced vehicle cooling technologies before testing by using an integrated modeling process. Evaluating the heat load on a vehicle under real world conditions is a difficult task. An accepted method to evaluate passenger compartment airflow and heat transfer is computational fluid dynamics. (CFD). Combining analytical models with CFD provides a powerful tool to assist industry both on current vehicles and on future design studies. Flow chart showing the vehicle integrated modeling process which considers solar radiation, air conditioning, and vehicles with CAD, glazing, cabin thermal/fluid, and thermal comfort modeling tools. Results are provided for fuel economy, tailpipe emissions and occupant thermal comfort.

437

EPRI/GRI Load Shape Workshop: Load Data Analysis for Gas and Electric Markets  

Science Conference Proceedings (OSTI)

Load shapes, representing usage patterns in the electric and gas industry, are a key factor in energy company operations and management. In the emerging restructured energy market, retail energy suppliers market energy to final customers and must arrange for electricity generation or gas delivery to meet their customers' needs. EPRI and GRI sponsored a two-day workshop in June, 1999 that addressed a range of issues associated with load shapes, including modeling, profiling for retail market settlement, r...

1999-11-10T23:59:59.000Z

438

Load diagram for a perforated plate tray  

E-Print Network (OSTI)

1 decimals noggrannhet c. Upprita i x,y-diagrammet q-linjen och bestäm (grafiskt, eller med must be produced. The feed stream F is a saturated liquid, i.e. q = 1, while the reflux ratio R = 1Load diagram for a perforated plate tray vG, vL: velocities G, L: densities QL, QG: volume flows H

Zevenhoven, Ron

439

Composition containing aerogel substrate loaded with tritium  

DOE Patents (OSTI)

The invention provides a process for loading an aerogel substrate with tritium and the resultant compositions. According to the process, an aerogel substrate is hydrolyzed so that surface OH groups are formed. The hydrolyzed aerogel is then subjected to tritium exchange employing, for example, a tritium-containing gas, whereby tritium atoms replace H atoms of surface OH groups. OH and/or CH groups of residual alcohol present in the aerogel may also undergo tritium exchange.

Ashley, Carol S. (Albuquerque, NM); Brinker, C. Jeffrey (Albuquerque, NM); Ellefson, Robert E. (Centerville, OH); Gill, John T. (Miamisburg, OH); Reed, Scott (Albuquerque, NM); Walko, Robert J. (Albuquerque, NM)

1992-01-01T23:59:59.000Z

440

Electricity pricing for conservation and load shifting  

Science Conference Proceedings (OSTI)

The electricity industry is facing the challenge of increasing costs of reliably meeting demand growth and fully complying with legislative renewable portfolio standards and greenhouse gas reduction targets. However, an electric utility's existing tariffs often don't have rates that increase with consumption volume or vary by time of use, thus not fully exploiting the potential benefits from customer conservation and load shifting. (author)

Orans, Ren; Woo, C.K.; Horii, Brian; Chait, Michele; DeBenedictis, Andrew

2010-04-15T23:59:59.000Z

Note: This page contains sample records for the topic "load serving entity" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Combined transmission distribution load flow model employing system reduction and voltage variable load representation  

SciTech Connect

In the few decades since its introduction the digital computer has found widespread application within the electric power industry. One of the more fruitful areas for its utilization has been in the determination of the steady-state voltage conditions throughout the system. A power system naturally breaks down into two very distinct parts: transmission and distribution, and traditionally, the voltage problem has been separated the same way. In the transmission system it is referred to as a load flow problem, and in the distribution part it is called a voltage profile. In addition, the loads are often treated differently. Transmission loads are usually considered to be constant power, and the equations that result are therefore nonlinear. In the distribution portion the loads, though specified in terms of power, are sometimes handled as constant impedances, with linear equations. This work produced a new model wherein a mesh transmission system is combined with a radial distribution system and they are solved simultaneously. A system reduction technique is used to eliminate part of the transmission system from consideration, and thereby keep the problem at a manageable size. The solution algorithm incorporates a voltage variable load model which approximates the behavior of real loads more nearly than the common representations.

Enouen, P.W.

1985-01-01T23:59:59.000Z

442

ALPHA ATTENUATION DUE TO DUST LOADING  

SciTech Connect

Previous studies had been done in order to show the attenuation of alpha particles in filter media. These studies provided an accurate correction for this attenuation, but there had not yet been a study with sufficient results to properly correct for attenuation due to dust loading on the filters. At the Savannah River Site, filter samples are corrected for attenuation due to dust loading at 20%. Depending on the facility the filter comes from and the duration of the sampling period, the proper correction factor may vary. The objective of this study was to determine self-absorption curves for each of three counting instruments. Prior work indicated significant decreases in alpha count rate (as much as 38%) due to dust loading, especially on filters from facilities where sampling takes place over long intervals. The alpha count rate decreased because of a decrease in the energy of the alpha. The study performed resulted in a set of alpha absorption curves for each of three detectors. This study also took into account the affects of the geometry differences in the different counting equipment used.

Dailey, A; Dennis Hadlock, D

2007-08-09T23:59:59.000Z

443

Load controller and method to enhance effective capacity of a photovotaic power supply using a dynamically determined expected peak loading  

DOE Patents (OSTI)

A load controller and method are provided for maximizing effective capacity of a non-controllable, renewable power supply coupled to a variable electrical load also coupled to a conventional power grid. Effective capacity is enhanced by monitoring power output of the renewable supply and loading, and comparing the loading against the power output and a load adjustment threshold determined from an expected peak loading. A value for a load adjustment parameter is calculated by subtracting the renewable supply output and the load adjustment parameter from the current load. This value is then employed to control the variable load in an amount proportional to the value of the load control parameter when the parameter is within a predefined range. By so controlling the load, the effective capacity of the non-controllable, renewable power supply is increased without any attempt at operational feedback control of the renewable supply. The expected peak loading of the variable load can be dynamically determined within a defined time interval with reference to variations in the variable load.

Perez, Richard (Delmar, NY)

2003-04-01T23:59:59.000Z

444

Definition: Direct Load Control Device | Open Energy Information  

Open Energy Info (EERE)

Load Control Device Load Control Device Jump to: navigation, search Dictionary.png Direct Load Control Device A remotely controllable switch that can turn power to a load or appliance on or off. Such a device could also be used to regulate the amount of power that a load can consume. Direct load control devices can be operated by a utility or third party energy provider to reduce a customer's energy demand at certain times.[1] Related Terms power, load References ↑ https://www.smartgrid.gov/category/technology/direct_load_control_device [[Ca LikeLike UnlikeLike You like this.Sign Up to see what your friends like. tegory: Smart Grid Definitionssmart grid,smart grid, |Template:BASEPAGENAME]]smart grid,smart grid, Retrieved from "http://en.openei.org/w/index.php?title=Definition:Direct_Load_Control_Device&oldid=502631

445

G&T adds versatile load management system  

SciTech Connect

Wolverine`s load management system was designed in response to the need to reduce peak demand. The Energy Management System (EMS) prepares short term (seven day) load forecasts, based on a daily peak demand forecst, augmented by a similar day profile based on weather conditions. The software combines the similar day profile with the daily peak demand forecast to yield an hourly load forecast for an entire week. The software uses the accepted load forecast case in many application functions, including interchange scheduling, unit commitment, and transaction evaluation. In real time, the computer updates the accepted forecast hourly, based in actual changes in the weather and load. The load management program executes hourly. The program uses impact curves to calculate a load management strategy that reduces the load forecast below a desired load threshold.

Nickel, J.R.; Baker, E.D.; Holt, J.W.; Chan, M.L.

1995-04-01T23:59:59.000Z

446

Development and characterization of a multi-camera 2D-vision system for enhanced performance of a drink serving robotic cell  

Science Conference Proceedings (OSTI)

A 2D-vision system is integrated into a drink-serving robotic cell, to enhance its flexibility. Two videocameras are used in a hybrid configuration scheme. The former is rigidly mounted on the robot end effector, the latter is fixed to the workplace. ... Keywords: 2D calibration, Blob analysis, Machine vision, Pattern-matching, Robotics

Paolo Bellandi; Giovanna Sansoni; Angelo Vertuan

2012-02-01T23:59:59.000Z

447

Residential equipment part load curves for use in DOE-2  

SciTech Connect

DOE-2 (DOE2 90) includes several correlation curves that predict the energy use of systems underpart load conditions. DOE-2 simulates systems on an hour-by-hour basis, so the correlations are intended to predict part load energy use (and efficiency) as a function of the part load ratio (PLR) for each hour, where PLR = Hourly Load/Available Capacity. Generally residential and small commercial HVAC equipment meets the load at off-design conditions by cycling on and off. Therefore, the part load correlations must predict the degradation due to this on and off operation over an hourly interval.

Henderson, Hugh; Huang, Y.J.; Parker, D.

1999-02-01T23:59:59.000Z

448

The effect of load parameters on system thermal performance  

SciTech Connect

The effects of load size, load profile and hot water set temperature on system thermal performance are investigated in order to determine the relative importance of these design parameters in sizing a solar water heating system. The WATSUN IV computer program was used to introduce various load sizes, load profiles and set temperatures to a base model. The results indicate that variations in load size have a significant effect on the thermal performance of the system. However, variations in load profile and hot water set temperature seem to have no significant effect on system performance.

Vakili, M.

1984-02-01T23:59:59.000Z

449

Methods for Analyzing Electric Load Shape and its Variability  

Science Conference Proceedings (OSTI)

Current methods of summarizing and analyzing electric load shape are discussed briefly and compared. Simple rules of thumb for graphical display of load shapes are suggested. We propose a set of parameters that quantitatively describe the load shape in many buildings. Using the example of a linear regression model to predict load shape from time and temperature, we show how quantities such as the load?s sensitivity to outdoor temperature, and the effectiveness of demand response (DR), can be quantified. Examples are presented using real building data.

Price, Philip

2010-05-12T23:59:59.000Z

450

SLUDGE TREATMENT PROJECT COST COMPARISON BETWEEN HYDRAULIC LOADING AND SMALL CANISTER LOADING CONCEPTS  

SciTech Connect

The Sludge Treatment Project (STP) is considering two different concepts for the retrieval, loading, transport and interim storage of the K Basin sludge. The two design concepts under consideration are: (1) Hydraulic Loading Concept - In the hydraulic loading concept, the sludge is retrieved from the Engineered Containers directly into the Sludge Transport and Storage Container (STSC) while located in the STS cask in the modified KW Basin Annex. The sludge is loaded via a series of transfer, settle, decant, and filtration return steps until the STSC sludge transportation limits are met. The STSC is then transported to T Plant and placed in storage arrays in the T Plant canyon cells for interim storage. (2) Small Canister Concept - In the small canister concept, the sludge is transferred from the Engineered Containers (ECs) into a settling vessel. After settling and decanting, the sludge is loaded underwater into small canisters. The small canisters are then transferred to the existing Fuel Transport System (FTS) where they are loaded underwater into the FTS Shielded Transfer Cask (STC). The STC is raised from the basin and placed into the Cask Transfer Overpack (CTO), loaded onto the trailer in the KW Basin Annex for transport to T Plant. At T Plant, the CTO is removed from the transport trailer and placed on the canyon deck. The CTO and STC are opened and the small canisters are removed using the canyon crane and placed into an STSC. The STSC is closed, and placed in storage arrays in the T Plant canyon cells for interim storage. The purpose of the cost estimate is to provide a comparison of the two concepts described.

GEUTHER J; CONRAD EA; RHOADARMER D

2009-08-24T23:59:59.000Z

451

Smard Grid Software Applications for Distribution Network Load Forecasting Eugene A. Feinberg, Jun Fei  

E-Print Network (OSTI)

of the distribution network. Keywords: load forecasting, feeder, transformer, load pocket, SmartGrid I. INTRODUCTION

Feinberg, Eugene A.

452

Distribution load study aids system planning  

SciTech Connect

The Walnut Metering Project is an experimental substation and distribution system metering installation designed to provide quantitative data for distribution system planning. The design and operation of the metering equipment are discussed. After 3 years of operation it was concluded that the primary economic benefits anticipated from the determination of substation area diversity characteristics did not materialize because the peaking characteristics of the substations in the area were typically coincident with each other. However, the data obtained had a significant positive impact, both economically and operationally, in the field of equipment loadability, and is beneficial to activities related to load projections and distribution system planning. (LCL)

Scofield J.M.

1976-07-01T23:59:59.000Z

453

DIELECTRIC-LOADED WAVE-GUIDES  

DOE Patents (OSTI)

This patent presents a particular arrangement for delectric loading of a wave-guide carrying an electromagnetic wave in the E or TM mode of at least the second order, to reduce the power dissipated as the result of conduction loss in the wave-guide walls. To achieve this desirabie result, the effective dielectric constants in the radial direction of adjacent coaxial tubular regions bounded approximateiy by successive nodai surfaces within the electromagnetic field are of two different values alternating in the radial direction, the intermost and outermost regions being of the lower value, and the dielectric constants between nodes are uniform.

Robertson-Shersby-Harvie, R.B.; Mullett, L.B.

1957-04-23T23:59:59.000Z

454

Analysis of parametric transformer with rectifier load  

SciTech Connect

This paper describes a push-pull parametric transformer constructed using a pair of orthogonal-cores. The operating characteristics of the parametric transformer with a rectifier load were analyzed based on SPICE simulations. The analysis results show good agreement with experiment. It was found that the input surge current of the full-wave rectifier circuit with a smoothing capacitor can be compensated by the parametric transformer. Use of the parametric transformer as a power stabilizer is anticipated owing to its various functions such as for voltage regulation and overload protection.

Ichinokura, O.; Jinzenji, T. (Tohoku Univ., Sendai (Japan)); Tajima, K. (Akita Univ. (Japan))

1993-03-01T23:59:59.000Z

455

Crack coalescence in rock-like material under cycling loading  

E-Print Network (OSTI)

A total of 170 tests (68 tests for monotonic loading, 102 tests for cyclic loading) have been performed to investigate crack initiation, propagation and coalescence. The specimens have two pre-existing flaws which are ...

Ko, Tae Young, 1973-

2005-01-01T23:59:59.000Z

456

NREL: Vehicle Ancillary Loads Reduction - About the Project  

NLE Websites -- All DOE Office Websites (Extended Search)

same effect on fuel cell power sources of the future. The largest ancillary load is the air-conditioning system when it is operating. (Typically it imposes a mechanical load of...

457

Assessing and Reducing Miscellaneous Electric Loads (MELs) in Lodging  

SciTech Connect

Miscellaneous electric loads (MELs) are the loads outside of a building's core functions of heating, ventilating, air conditioning, lighting, and water heating. This report reviews methods to reduce MELs in lodging.

Rauch, Emily M.

2011-09-01T23:59:59.000Z

458

Dynamic load management for MMOGs in distributed environments  

Science Conference Proceedings (OSTI)

To support thousands of concurrent players in virtual worlds simulated by contemporary Massively Multiplayer Online Games, most implementations employ static game world partitioning for distributing the load among multiple game server instances. Further, ... Keywords: load balancing, mmogs

Herbert Jordan; Radu Prodan; Vlad Nae; Thomas Fahringer

2010-05-01T23:59:59.000Z

459

Load Profiling Based Routing for Guaranteed Bandwidth Flows  

E-Print Network (OSTI)

. To support the stringent Quality of Service (QoS) requirements of real-time (e.g. audio/video) applications in integrated services networks, several routing algorithms that allow for the reservation of the needed bandwidth over a Virtual Circuit (VC), established on one of several candidate routes, have been proposed. Traditionally, such routing is done using the least-loaded concept, and thus results in balancing the load across the set of candidate routes. In this paper, we propose the use of load profiling as an attractive alternative to load balancing for routing guaranteed bandwidth VCs (flows). Load profiling techniques allow the distribution of "available" bandwidth across a set of candidate routes to match the characteristics of incoming VC QoS requests. We thoroughly characterize the performance of VC routing using load profiling and contrast it to routing using load balancing and load packing. We do so both analytically and via extensive simulations of multi-class traffic r...

Ibrahim Matta; Azer Bestavros; Marwan Krunz

1999-01-01T23:59:59.000Z

460

deformation and failure of metals subjected to laser shock loading  

Science Conference Proceedings (OSTI)

The spall stress in laser pulse loading is much higher than in gas-gun loading because of the much ... Dynamic Contact Failure of Two Brittle Particles under Compression ... Natural Fiber Composite in a Novel Multi-Material Ballistic Armor.

Note: This page contains sample records for the topic "load serving entity" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Exploiting home automation protocols for load monitoring in smart buildings  

Science Conference Proceedings (OSTI)

Monitoring and controlling electrical loads is crucial for demand-side energy management in smart grids. Home automation (HA) protocols, such as X10 and Insteon, have provided programmatic load control for many years, and are being widely deployed in ...

David Irwin; Sean Barker; Aditya Mishra; Prashant Shenoy; Anthony Wu; Jeannie Albrecht

2011-11-01T23:59:59.000Z

462

A fuzzy logic based approach to direct load control  

SciTech Connect

Demand side management programs are strategies designed to alter the shape of the load curve. In order to successfully implement such a strategy, customer acceptance of the program is vital. It is thus desirable to design a model for direct load control which may accommodate customer preferences. This paper presents a methodology for optimizing both customer satisfaction and utility unit commitment savings, based on a fuzzy load model for the direct load control of appliances.

Bhattacharyya, K.; Crow, M.L. [Univ. of Missouri, Rolla, MO (United States). Dept. of Electrical Engineering

1996-05-01T23:59:59.000Z

463

Load Profiling and Settlement for Retail Markets Methods Assessment Study  

Science Conference Proceedings (OSTI)

Retail electric competition requires estimation of hourly loads for each retail supplier. Load profiling is the means by which loads for customers who do not have hourly metering are accounted for. This report presents an assessment of alternative load profiling and settlement methods for retail electric markets and provides a framework for evaluating costs and benefits of potential improvements to profiling and settlement systems. This report is available only to funders of Program 101A or 101.001. Fund...

1999-06-01T23:59:59.000Z

464

Load management strategies for electric utilities: a production cost simulation  

SciTech Connect

This paper deals with the development and application of a simulation model for analyzing strategies for managing the residential loads of electric utilities. The basic components of the model are (1) a production-cost model, which simulates daily operation of an electric power system; (2) a load model, which disaggregates system loads into appliance loads and other loads; and (3) a comparison model, which compares the production costs and energy consumption needed to meet a particular load profile to the corresponding costs and energy consumption required for another load profile. The profiles in each pair define alternative ways of meeting the same demand. A method for disaggregating load profiles into appliance components is discussed and several alternative strategies for residential load management for a typical northeastern electric utility are formulated. The method is based on an analysis of the composition of electric loads for a number of classes of residential customers in the model utility system. The effect of alternative load management strategies on the entire residential loadcurve is determined by predicting the effects of these strategies on the specific appliance components of the loadcurve. The results of using the model to analyze alternative strategies for residential load management suggest that load management strategies in the residential sector, if adopted by utilities whose operating and load characteristics are similar to those of the system modeled here, must take into account a wide variety of appliances to achieve significant changes in the total load profile. Moreover, the results also suggest that it is not easy to reduce costs significantly through new strategies for managing residential loads only and that, to be worthwhile, cost-reducing strategies will have to encompass many kinds of appliances.

Blair, P.D.

1979-03-01T23:59:59.000Z

465

Behavior of Laminate Reactive Materials under Dynamic Loading ...  

Science Conference Proceedings (OSTI)

Presentation Title, Behavior of Laminate Reactive Materials under Dynamic Loading ... Atomistically-Informed Dislocation Dynamics Simulations of High Rate  ...

466

Failure Prediction of Complex Structures Under Loading and ...  

loads; environmental corrosion is another significant stress factor. ... among different materials and how they exhibit crack growth. This method can ...

467

Spinning Reserve from Hotel Air Conditioning Load - SHORT VERSION  

SciTech Connect

Even though preliminary tests were not conducted during times of highest system or hotel loading during the summer, they showed that hotel load can be curtailed by 22 to 37 percent depending on the outdoor temperature and time of day. Full response occurred in 12 to 60 seconds from when the system operator's command to shed load was issued and the load drop was very rapid.

Kueck, John D [ORNL; Kirby, Brendan J [ORNL

2008-01-01T23:59:59.000Z

468

SAPHIRE 8 Volume 7 - Data Loading  

Science Conference Proceedings (OSTI)

The Systems Analysis Programs for Hands-on Integrated Reliability Evaluations (SAPHIRE) is a software application developed for performing a complete probabilistic risk assessment (PRA) using a personal computer. SAPHIRE Version 8 is funded by the U.S. Nuclear Regulatory Commission and developed by the Idaho National Laboratory. This report is intended to assist the user to enter PRA data into the SAPHIRE program using the built-in MAR-D ASCII-text file data transfer process. Towards this end, a small sample database is constructed and utilized for demonstration. Where applicable, the discussion includes how the data processes for loading the sample database relate to the actual processes used to load a larger PRA models. The procedures described herein were developed for use with SAPHIRE Version 8. The guidance specified in this document will allow a user to have sufficient knowledge to both understand the data format used by SAPHIRE and to carry out the transfer of data between different PRA projects.

K. J. Kvarfordt; S. T. Wood; C. L. Smith; S. R. Prescott

2011-03-01T23:59:59.000Z

469

A new approach applied to adaptive centralized load shedding scheme  

Science Conference Proceedings (OSTI)

One of major contingencies of an electric power system is due to imbalance between loads and generated power. This leads to instability in the power system and hence to a blackout. A load shedding scheme may be used to avoid such problem by reducing ... Keywords: adaptive load shedding scheme, critical power, power system, threshold power

Hamid Bentarzi; Abderrahmane Ouadi; Nadir Ghout; Farid Maamri; Nikos E. Mastorakis

2009-12-01T23:59:59.000Z

470

Model Based Load Indices (MBLI) for Scientific Stefan P. Muszala  

E-Print Network (OSTI)

Model Based Load Indices (MBLI) for Scientific Simulation by Stefan P. Muszala B.S., B.A. Rutgers and Computer Engineering 2008 #12;This thesis entitled: Model Based Load Indices (MBLI) for Scientific Engineering) Model Based Load Indices (MBLI) for Scientific Simulation Thesis directed by Dr. Daniel Connors

Colorado at Boulder, University of

471

Gravity Load Collapse of Building Frames during Earthquakes  

E-Print Network (OSTI)

Gravity Load Collapse of Building Frames during Earthquakes J. P. Moehle, K. J. Elwood, H. Sezen to frames designed primarily for gravity loads. Columns generally were not designed to have strengths capacity of the column. As the axial capacity diminishes, the gravity loads carried by the column must

Sezen, Halil

472

Dynamic modelling of metals - Time scales and target loads  

Science Conference Proceedings (OSTI)

Over the past decade steady-state methods have been developed to assess critical loads of metals avoiding long-term risks in view of food quality and eco-toxicological effects on organisms in soils and surface waters. However, dynamic models are needed ... Keywords: Critical loads, Delay times, Dynamic modelling, Metals, Scenario analysis, Target loads

Maximilian Posch; Wim de Vries

2009-01-01T23:59:59.000Z

473

Finite element modeling of transmission line under downburst wind loading  

Science Conference Proceedings (OSTI)

Despite the fact that extensive research has been carried out on transmission lines subjected to normal wind loads, their behaviour under high intensity wind loads (HIW), such as downburst, is poorly defined. This paper describes a detailed numerical ... Keywords: Downbursts, Finite element, Microbursts, Transmission line, Transmission tower, Wind load

A. Y. Shehata; A. A. El Damatty; E. Savory

2005-10-01T23:59:59.000Z

474

Variable Selection for Five-Minute Ahead Electricity Load Forecasting  

Science Conference Proceedings (OSTI)

We use autocorrelation analysis to extract 6 nested feature sets of previous electricity loads for 5-minite ahead electricity load forecasting. We evaluate their predictive power using Australian electricity data. Our results show that the most important ... Keywords: very short-term electricity load forecasting, prediction, variable selection, autocorrelation analysis

Irena Koprinska; Rohen Sood; Vassilios Agelidis

2010-08-01T23:59:59.000Z

475

Power load forecasting Organization: Huizhou Electric Power, P. R. China  

E-Print Network (OSTI)

, regression, artificial intelligence. 1. Introduction Accurate models for electric power load forecasting are essential to the operation and planning of a utility company. Load forecasting helps an electric utility as electric load forecasting. In particular, ARMA (autoregressive moving average), ARIMA (autore- gressive

476

Workload-Aware Load Balancing for Clustered Web Servers  

Science Conference Proceedings (OSTI)

We focus on load balancing policies for homogeneous clustered Web servers that tune their parameters on-the-fly to adapt to changes in the arrival rates and service times of incoming requests. The proposed scheduling policy, AdaptLoad, monitors the incoming ... Keywords: Clustered Web servers, self-managing clusters, load balance, locality awareness, workload characterization, static and dynamic pages.

Qi Zhang; Alma Riska; Wei Sun; Evgenia Smirni; Gianfranco Ciardo

2005-03-01T23:59:59.000Z

477

Commercial Nonintrusive Load Monitoring System Beta Test Results  

Science Conference Proceedings (OSTI)

Monitoring many different individual loads on customer premises is a costly, complex, and trouble-prone operation. The availability of a single instrument that could plug into the meter socket and measure individual premise loads would greatly simplify and reduce the cost of customer load monitoring. This report provides the test results of such a prototype instrument.

1999-12-15T23:59:59.000Z

478

In situ Characterization of Pt Catalysts Supported on Ceria Modified TiO(2) for the WGS reaction: Influence of Ceria Loading  

Science Conference Proceedings (OSTI)

This work analyzes the influence of cerium content (6-15 wt%) on a TiO{sub 2} support over the structure and water gas shift (WGS) activity of Pt catalysts. The structural properties of these Pt/Ce-TiO{sub 2} catalysts were characterized by XRD, TEM and XANES. Physicochemical characterization of the catalysts showed differences in the structure and dispersion of Ce entities on the support with Ce loading. For the samples with low ceria content (6 wt%), cerium is deposited on the support in the form of CeO{sub x} clusters in a highly dispersed state in close interaction with the Ti atoms. The formation of CeO{sub x} clusters at low Ce-loading on the support facilitates the dispersion of small particles of Pt and improves the reducibility of ceria component at low temperatures. The changes in platinum dispersion and support reducibility with Ce-loading on the TiO{sub 2} support lead to significant differences in the WGS activity. Pt supported on the sample with lower Ce content (6 wt%) shows better activity than those corresponding to catalysts with higher Ce content (15 wt%). Activity measurements coupled with catalysts characterization suggest that the improvement in the reducibility of the support with lower Ce content was associated with the presence of CeO{sub x} clusters of high reducibility that improve the chemical activity of the oxide-metal interfaces at which the WGS reaction takes place.

Rodriguez J. A.; Barrio, L.; Zhou, G.; Gonzalez, I.D.; Estrella, M.; Hanson, J.; Navarro, R.M.; Fierro, J.L.G.

2012-01-01T23:59:59.000Z

479

On traffic load distribution and load balancing in dense wireless multihop networks  

Science Conference Proceedings (OSTI)

We study the load balancing problem in a dense wireless multihop network, where a typical path consists of a large number of hops, that is, the spatial scales of a typical distance between source and destination and mean distance between the neighboring ...

Esa Hyytiä; Jorma Virtamo

2007-01-01T23:59:59.000Z

480

Probability based load factors for design of concrete containment structures  

SciTech Connect

This paper describes a procedure for developing probability-based load combinations for the design of concrete containments. The proposed criteria are in a load and resistance factor design (LRFD) format. The load factors and resistance factors are derived for use in limit states design and are based on a target limit state probability. In this paper, the load factors for accident pressure and safe shutdown earthquake are derived for three target limit state probabilities. Other load factors are recommended on the basis of prior experience with probability-based design criteria for ordinary building construction. 6 refs.

Hwang, H.; Kagami, S.; Reich, M.; Ellingwood, B.; Shinozuka, M.

1985-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "load serving entity" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Estimation of structural reliability under combined loads. [PWR; BWR  

DOE Green Energy (OSTI)

For the overall safety evaluation of seismic category I structures subjected to various load combinations, a quantitative measure of the structural reliability in terms of a limit state probability can be conveniently used. For this purpose, the reliability analysis method for dynamic loads, which has recently been developed by the authors, was combined with the existing standard reliability analysis procedure for static and quasi-static loads. The significant parameters that enter into the analysis are: the rate at which each load (dead load, accidental internal pressure, earthquake, etc.) will occur, its duration and intensity. All these parameters are basically random variables for most of the loads to be considered. For dynamic loads, the overall intensity is usually characterized not only by their dynamic components but also by their static components. The structure considered in the present paper is a reinforced concrete containment structure subjected to various static and dynamic loads such as dead loads, accidental pressure, earthquake acceleration, etc. Computations are performed to evaluate the limit state probabilities under each load combination separately and also under all possible combinations of such loads.

Shinozuka, M.; Kako, T.; Hwang, H.; Brown, P.; Reich, M.

1983-01-01T23:59:59.000Z

482

DC switching regulated power supply for driving an inductive load  

DOE Patents (OSTI)

A power supply for driving an inductive load current from a dc power supply hrough a regulator circuit including a bridge arrangement of diodes and switching transistors controlled by a servo controller which regulates switching in response to the load current to maintain a selected load current. First and second opposite legs of the bridge are formed by first and second parallel-connected transistor arrays, respectively, while the third and fourth legs of the bridge are formed by appropriately connected first and second parallel connected diode arrays, respectively. The regulator may be operated in three "stages" or modes: (1) For current runup in the load, both first and second transistor switch arrays are turned "on" and current is supplied to the load through both transistor arrays. (2) When load current reaches the desired level, the first switch is turned "off", and load current "flywheels" through the second switch array and the fourth leg diode array connecting the second switch array in series with the load. Current is maintained by alternating between modes 1 and 2 at a suitable duty cycle and switching rate set by the controller. (3) Rapid current rundown is accomplished by turning both switch arrays "off", allowing load current to be dumped back into the source through the third and fourth diode arrays connecting the source in series opposition with the load to recover energy from the inductive load. The three operating states are controlled automatically by the controller.

Dyer, George R. (Norris, TN)

1986-01-01T23:59:59.000Z

483

NREL: Vehicle Ancillary Loads Reduction - Physiological Model  

NLE Websites -- All DOE Office Websites (Extended Search)

Physiological Model Physiological Model The Vehicle Ancillary Loads Reduction team developed a three-dimensional model to simulate human internal thermal physiological systems (muscle, blood, etc.) and thermoregulatory responses such as metabolic heat generation. The model was developed with ANSYS, a finite element software which computes heat flow by conduction, convection, and mass transport of the blood. A human tissue system model represents the human body, including the physiological and thermal properties of the tissues. The arms and legs consist of bone, muscle, fat, and skin. There are additional lung, abdominal, and brain tissues in the torso and head zones. The model calculates the conduction heat transfer based on the temperature gradients between the tissue nodes. Blood flow is modeled with a network of supply

484

Piezoelectric film load cell robot collision detector  

DOE Patents (OSTI)

A piezoelectric load cell which can be utilized for detecting collisions and obstruction of a robot arm end effector includes a force sensing element of metallized polyvinylidene fluoride (PVDF) film. The piezoelectric film sensing element and a resilient support pad are clamped in compression between upper and lower plates. The lower plate has a central recess in its upper face for supporting the support pad and sensing element, while the upper plate has a corresponding central projection formed on its lower face for bearing on the sensing element and support pad. The upper and lower plates are doweled together for concentric alignment and screwed together. The upper and lower plates are also adapted for mounting between the robot arm wrist and end effector. 3 figs.

Lembke, J.R.

1989-04-18T23:59:59.000Z

485

Piezoelectric film load cell robot collision detector  

DOE Patents (OSTI)

A piezoelectric load cell which can be utilized for detecting collisions and obstruction of a robot arm end effector includes a force sensing element of metallized polyvinylidene fluoride (PVDF) film. The piezoelectric film sensing element and a resilient support pad are clamped in compression between upper and lower plates. The lower plate has a central recess in its upper face for supporting the support pad and sensing element, while the upper plate has a corresponding central projection formed on its lower face for bearing on the sensing element and support pad. The upper and lower plates are dowelled together for concentric alignment and screwed together. The upper and lower plates are also adapted for mounting between the robot arm wrist and end effector. 3 figs.

Lembke, J.R.

1988-03-15T23:59:59.000Z

486

Active load control techniques for wind turbines.  

DOE Green Energy (OSTI)

This report provides an overview on the current state of wind turbine control and introduces a number of active techniques that could be potentially used for control of wind turbine blades. The focus is on research regarding active flow control (AFC) as it applies to wind turbine performance and loads. The techniques and concepts described here are often described as 'smart structures' or 'smart rotor control'. This field is rapidly growing and there are numerous concepts currently being investigated around the world; some concepts already are focused on the wind energy industry and others are intended for use in other fields, but have the potential for wind turbine control. An AFC system can be broken into three categories: controls and sensors, actuators and devices, and the flow phenomena. This report focuses on the research involved with the actuators and devices and the generated flow phenomena caused by each device.

van Dam, C.P. (University of California, Davis, CA); Berg, Dale E.; Johnson, Scott J. (University of California, Davis, CA)

2008-07-01T23:59:59.000Z

487

Building Energy Software Tools Directory: QwickLoad  

NLE Websites -- All DOE Office Websites (Extended Search)

QwickLoad QwickLoad QwickLoad logo QwickLoad uses the ASHRAE TFM (Transfer Function Method) algorithms combined with a screen interface that provides building load calculations. It includes a Duct Sizing Program and supports IP and SI units. QwickLoad Residential 7.0 provides heat gain and heat loss calculations for up to 10 zones. QwickLoad Commercial 7.0 provides heat gain and heat loss calculations for up to 500 zones. Zones and plenums can be added or deleted with one button click. Intuitive screens for entering building information. Default is automatically displayed. Construction types for roofs, walls, partitions, windows, shade types, and scheduling control. Complete air-conditioning and heating system control and supply, return, heating and cooling duct static pressure specification. Energy recovery ventilator can

488

Technical Assistance to ISO's and Grid Operators For Loads Providing  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Technical Assistance to ISO's and Grid Operators For Loads Technical Assistance to ISO's and Grid Operators For Loads Providing Ancillary Services To Enhance Grid Reliability Technical Assistance to ISO's and Grid Operators For Loads Providing Ancillary Services To Enhance Grid Reliability Project demonstrates and promotes the use of responsive load to provide ancillary services; helps ISOsand grid operators understand the resource and how best to apply it. Technical Assistance to ISO's and Grid Operators For Loads Providing Ancillary Services To Enhance Grid Reliability More Documents & Publications Loads Providing Ancillary Services: Review of International Experience 2012 Load as a Resource Program Peer Review New York Independent System Operator, Smart Grid RFI: Addressing Policy and Logistical Challenges.

489

Optimum matching of ohmic loads to the photovoltaic array  

SciTech Connect

Optimum matching of loads to the photovoltaic (PV) generator is most desirable for more accurate sizing, higher system performance and maximum utilization of the costly solar array generator. The quality of load matching depends on the PV array characteristics, the load characteristics, and the insolation profile. A matching factor is defined as the ratio of the load energy to the array maximum energy over a one day period. Optimum matching is achieved by determining the optimal array parameters with respect to the load parameters. Optimization is done using direct-search techniques. Results show that the theoretical optimum matching factor for an ohmic load is 94.34%. For an electrolytic load the matching factor could reach 99.83%. A maximum power tracker can be eliminated if optimum matching is achieved.

Khouzam, K.; Khouzam, L.; Groumpos, P. (Cleveland State Univ., OH (USA))

1991-01-01T23:59:59.000Z

490

Load Response Fundamentally Matches Power System Reliability Requirements  

Science Conference Proceedings (OSTI)

Responsive load is the most underutilized reliability resource available to the power system. Loads are frequently barred from providing the highest value and most critical reliability services; regulation and spinning reserve. Advances in communications and control technology now make it possible for some loads to provide both of these services. The limited storage incorporated in some loads better matches their response capabilities to the fast reliability-service markets than to the hourly energy markets. Responsive loads are frequently significantly faster and more accurate than generators, increasing power system reliability. Incorporating fast load response into microgrids further extends the reliability response capabilities that can be offered to the interconnected power system. The paper discusses the desired reliability responses, why this matches some loads' capabilities, what the advantages are for the power system, implications for communications and monitoring requirements, and how this resource can be exploited.

Kirby, Brendan J [ORNL

2007-01-01T23:59:59.000Z

491

Entity-Oriented Data Science  

Science Conference Proceedings (OSTI)

... Page 9. Common Graph Data Analysis Patterns ... Machine: Intel Core2 Quad CPU 2.66GHz machines with 4GB RAM running Ubuntu 12.04 Linux ...

2013-09-05T23:59:59.000Z

492

2010 ANNUAL REPORT SERVING THE MEMBERS WHO SERVE ...  

Science Conference Proceedings (OSTI)

Dec 31, 2010 ... The Minerals, Metals & Materials Society. 2. “TMS is just like a complete piece of material. Each participant is like a component of this material.”.

493

"YEAR","MONTH","STATE","UTILITY CODE","UTILITY NAME","RESIDENTIAL PHOTOVOLTAIC ELECTRIC ENERGY SOLD BACK (MWh)","COMMERCIAL PHOTOVOLTAIC ELECTRIC ENERGY SOLD BACK (MWh)","INDUSTRIAL PHOTOVOLTAIC ELECTRIC ENERGY SOLD BACK (MWh)","TRANSPORTATION PHOTOVOLTAIC ELECTRIC ENERGY SOLD BACK (MWh)","TOTAL PHOTOVOLTAIC ELECTRIC ENERGY SOLD BACK (MWh)","RESIDENTIAL PHOTOVOLTAIC INSTALLED NET METERING CAPACITY (MW)","COMMERCIAL PHOTOVOLTAIC INSTALLED NET METERING CAPACITY (MW)","INDUSTRIAL PHOTOVOLTAIC INSTALLED NET METERING CAPACITY (MW)","TRANSPORTATION PHOTOVOLTAIC INSTALLED NET METERING CAPACITY (MW)","TOTAL PHOTOVOLTAIC INSTALLED NET METERING CAPACITY (MW)","RESIDENTIAL PHOTOVOLTAIC NET METERING CUSTOMER COUNT","COMMERCIAL PHOTOVOLTAIC NET METERING CUSTOMER COUNT","INDUSTRIAL PHOTOVOLTAIC NET METERING CUSTOMER COUNT","TRANSPORTATION PHOTOVOLTAIC NET METERING CUSTOMER COUNT","TOTAL PHOTOVOLTAIC NET METERING CUSTOMER COUNT","RESIDENTIAL WIND ELECTRIC ENERGY SOLD BACK (MWh)","COMMERCIAL WIND ELECTRIC ENERGY SOLD BACK (MWh)","INDUSTRIAL WIND ELECTRIC ENERGY SOLD BACK (MWh)","TRANSPORTATION WIND ELECTRIC ENERGY SOLD BACK (MWh)","TOTAL WIND ELECTRIC ENERGY SOLD BACK (MWh)","RESIDENTIAL WIND INSTALLED NET METERING CAPACITY (MW)","COMMERCIAL WIND INSTALLED NET METERING CAPACITY (MW)","INDUSTRIAL WIND INSTALLED NET METERING CAPACITY (MW)","TRANSPORTATION WIND INSTALLED NET METERING CAPACITY (MW)","TOTAL WIND INSTALLED NET METERING CAPACITY (MW)","RESIDENTIAL WIND NET METERING CUSTOMER COUNT","COMMERCIAL WIND NET METERING CUSTOMER COUNT","INDUSTRIAL WIND NET METERING CUSTOMER COUNT","TRANSPORTATION WIND NET METERING CUSTOMER COUNT","TOTAL WIND NET METERING CUSTOMER COUNT","RESIDENTIAL OTHER ELECTRIC ENERGY SOLD BACK (MWh)","COMMERCIAL OTHER ELECTRIC ENERGY SOLD BACK (MWh)","INDUSTRIAL OTHER ELECTRIC ENERGY SOLD BACK (MWh)","TRANSPORTATION OTHER ELECTRIC ENERGY SOLD BACK (MWh)","TOTAL OTHER ELECTRIC ENERGY SOLD BACK (MWh)","RESIDENTIAL OTHER INSTALLED NET METERING CAPACITY (MW)","COMMERCIAL OTHER INSTALLED NET METERING CAPACITY (MW)","INDUSTRIAL OTHER INSTALLED NET METERING CAPACITY (MW)","TRANSPORTATION OTHER INSTALLED NET METERING CAPACITY (MW)","TOTAL OTHER INSTALLED NET METERING CAPACITY (MW)","RESIDENTIAL OTHER NET METERING CUSTOMER COUNT","COMMERCIAL OTHER NET METERING CUSTOMER COUNT","INDUSTRIAL OTHER NET METERING CUSTOMER COUNT","TRANSPORTATION OTHER NET METERING CUSTOMER COUNT","TOTAL OTHER NET METERING CUSTOMER COUNT","RESIDENTIAL TOTAL ENERGY SOLD BACK TO THE UTILITY (MWh)","COMMERCIAL TOTAL ELECTRIC ENERGY SOLD BACK (MWh)","INDUSTRIAL TOTAL ELECTRIC ENERGY SOLD BACK (MWh)","TRANSPORTATION TOTAL ELECTRIC ENERGY SOLD BACK (MWh)","TOTAL ELECTRIC ENERGY SOLD BACK (MWh)","RESIDENTIAL TOTAL INSTALLED NET METERING CAPACITY (MW)","COMMERCIAL TOTAL INSTALLED NET METERING CAPACITY (MW)","INDUSTRIAL TOTAL INSTALLED NET METERING CAPACITY (MW)","TRANSPORTATION TOTAL INSTALLED NET METERING CAPACITY (MW)","TOTAL INSTALLED NET METERING CAPACITY (MW)","RESIDENTIAL TOTAL NET METERING CUSTOMER COUNT","COMMERCIAL TOTAL NET METERING CUSTOMER COUNT","INDUSTRIAL TOTAL NET METERING CUSTOMER COUNT","TRANSPORTATION TOTAL NET METERING CUSTOMER COUNT","TOTAL NET METERING CUSTOMER COUNT","RESIDENTIAL ELECTRIC ENERGY SOLD BACK TO THE UTILITY FOR ALL STATES SERVED(MWh)","COMMERCIAL ELECTRIC ENERGY SOLD BACK TO THE UTILITY FOR ALL STATES SERVED(MWh)","INDUSTRIAL ELECTRIC ENERGY SOLD BACK TO THE UTILITY FOR ALL STATES SERVED(MWh)","TRANSPORTATION ELECTRIC ENERGY SOLD BACK TO THE UTILITY FOR ALL STATES SERVED(MWh)","TOTAL ELECTRIC ENERGY SOLD BACK TO THE UTILITYFOR ALL STATES SERVED(MWh)","RESIDENTIAL INSTALLED NET METERING CAPACITY FOR ALL STATES SERVED(MW)","COMMERCIAL INSTALLED NET METERING CAPACITY FOR ALL STATES SERVED(MW)","INDUSTRIAL INSTALLED NET METERING CAPACITY FOR ALL STATES SERVED(MW)","TRANSPORTATION INSTALLED NET METERING CAPACITY FOR ALL STATES SERVED(MW)","INSTALLED NET METERING CAPACITY FOR ALL STATES SERVED(MW)","RESIDENTIAL NET METERING CUSTOMER COUNT FOR ALL STATES SERVED","COMMERCIAL NET METERING CUSTOMER COUNT FOR ALL STATES SERVED","INDUSTRIAL NET METERING CUSTOMER COUNT FOR ALL STATES SERVED","TRANSPORTATION NET METERING CUSTOMER COUNT FOR ALL STATES SERVED","NET METERING CUSTOMER COUNT FOR ALL STATES SERVED"  

U.S. Energy Information Administration (EIA) Indexed Site

UTILITYFOR ALL STATES SERVED(MWh)","RESIDENTIAL INSTALLED NET METERING CAPACITY FOR ALL STATES SERVED(MW)","COMMERCIAL INSTALLED NET METERING CAPACITY FOR ALL STATES SERVED(MW)","INDUSTRIAL INSTALLED NET METERING CAPACITY FOR ALL STATES SERVED(MW)","TRANSPORTATION INSTALLED NET METERING CAPACITY FOR ALL STATES SERVED(MW)","INSTALLED NET METERING CAPACITY FOR ALL STATES SERVED(MW)","RESIDENTIAL NET METERING CUSTOMER COUNT FOR ALL STATES SERVED","COMMERCIAL NET METERING CUSTOMER COUNT FOR ALL STATES SERVED","INDUSTRIAL NET METERING CUSTOMER COUNT FOR ALL STATES SERVED","TRANSPORTATION NET METERING CUSTOMER COUNT FOR ALL STATES SERVED","NET METERING CUSTOMER COUNT FOR ALL STATES SERVED"

494

"YEAR","MONTH","STATE","UTILITY CODE","UTILITY NAME","RESIDENTIAL PHOTOVOLTAIC ELECTRIC ENERGY SOLD BACK (MWh)","COMMERCIAL PHOTOVOLTAIC ELECTRIC ENERGY SOLD BACK (MWh)","INDUSTRIAL PHOTOVOLTAIC ELECTRIC ENERGY SOLD BACK (MWh)","TRANSPORTATION PHOTOVOLTAIC ELECTRIC ENERGY SOLD BACK (MWh)","TOTAL PHOTOVOLTAIC ELECTRIC ENERGY SOLD BACK (MWh)","RESIDENTIAL PHOTOVOLTAIC INSTALLED NET METERING CAPACITY (MW)","COMMERCIAL PHOTOVOLTAIC INSTALLED NET METERING CAPACITY (MW)","INDUSTRIAL PHOTOVOLTAIC INSTALLED NET METERING CAPACITY (MW)","TRANSPORTATION PHOTOVOLTAIC INSTALLED NET METERING CAPACITY (MW)","TOTAL PHOTOVOLTAIC INSTALLED NET METERING CAPACITY (MW)","RESIDENTIAL PHOTOVOLTAIC NET METERING CUSTOMER COUNT","COMMERCIAL PHOTOVOLTAIC NET METERING CUSTOMER COUNT","INDUSTRIAL PHOTOVOLTAIC NET METERING CUSTOMER COUNT","TRANSPORTATION PHOTOVOLTAIC NET METERING CUSTOMER COUNT","TOTAL PHOTOVOLTAIC NET METERING CUSTOMER COUNT","RESIDENTIAL WIND ELECTRIC ENERGY SOLD BACK (MWh)","COMMERCIAL WIND ELECTRIC ENERGY SOLD BACK (MWh)","INDUSTRIAL WIND ELECTRIC ENERGY SOLD BACK (MWh)","TRANSPORTATION WIND ELECTRIC ENERGY SOLD BACK (MWh)","TOTAL WIND ELECTRIC ENERGY SOLD BACK (MWh)","RESIDENTIAL WIND INSTALLED NET METERING CAPACITY (MW)","COMMERCIAL WIND INSTALLED NET METERING CAPACITY (MW)","INDUSTRIAL WIND INSTALLED NET METERING CAPACITY (MW)","TRANSPORTATION WIND INSTALLED NET METERING CAPACITY (MW)","TOTAL WIND INSTALLED NET METERING CAPACITY (MW)","RESIDENTIAL WIND NET METERING CUSTOMER COUNT","COMMERCIAL WIND NET METERING CUSTOMER COUNT","INDUSTRIAL WIND NET METERING CUSTOMER COUNT","TRANSPORTATION WIND NET METERING CUSTOMER COUNT","TOTAL WIND NET METERING CUSTOMER COUNT","RESIDENTIAL OTHER ELECTRIC ENERGY SOLD BACK (MWh)","COMMERCIAL OTHER ELECTRIC ENERGY SOLD BACK (MWh)","INDUSTRIAL OTHER ELECTRIC ENERGY SOLD BACK (MWh)","TRANSPORTATION OTHER ELECTRIC ENERGY SOLD BACK (MWh)","TOTAL OTHER ELECTRIC ENERGY SOLD BACK (MWh)","RESIDENTIAL OTHER INSTALLED NET METERING CAPACITY (MW)","COMMERCIAL OTHER INSTALLED NET METERING CAPACITY (MW)","INDUSTRIAL OTHER INSTALLED NET METERING CAPACITY (MW)","TRANSPORTATION OTHER INSTALLED NET METERING CAPACITY (MW)","TOTAL OTHER INSTALLED NET METERING CAPACITY (MW)","RESIDENTIAL OTHER NET METERING CUSTOMER COUNT","COMMERCIAL OTHER NET METERING CUSTOMER COUNT","INDUSTRIAL OTHER NET METERING CUSTOMER COUNT","TRANSPORTATION OTHER NET METERING CUSTOMER COUNT","TOTAL OTHER NET METERING CUSTOMER COUNT","RESIDENTIAL TOTAL ENERGY SOLD BACK TO THE UTILITY (MWh)","COMMERCIAL TOTAL ELECTRIC ENERGY SOLD BACK (MWh)","INDUSTRIAL TOTAL ELECTRIC ENERGY SOLD BACK (MWh)","TRANSPORTATION TOTAL ELECTRIC ENERGY SOLD BACK (MWh)","TOTAL ELECTRIC ENERGY SOLD BACK (MWh)","RESIDENTIAL TOTAL INSTALLED NET METERING CAPACITY (MW)","COMMERCIAL TOTAL INSTALLED NET METERING CAPACITY (MW)","INDUSTRIAL TOTAL INSTALLED NET METERING CAPACITY (MW)","TRANSPORTATION TOTAL INSTALLED NET METERING CAPACITY (MW)","TOTAL INSTALLED NET METERING CAPACITY (MW)","RESIDENTIAL TOTAL NET METERING CUSTOMER COUNT","COMMERCIAL TOTAL NET METERING CUSTOMER COUNT","INDUSTRIAL TOTAL NET METERING CUSTOMER COUNT","TRANSPORTATION TOTAL NET METERING CUSTOMER COUNT","TOTAL NET METERING CUSTOMER COUNT","RESIDENTIAL ELECTRIC ENERGY SOLD BACK TO THE UTILITY FOR ALL STATES SERVED(MWh)","COMMERCIAL ELECTRIC ENERGY SOLD BACK TO THE UTILITY FOR ALL STATES SERVED(MWh)","INDUSTRIAL ELECTRIC ENERGY SOLD BACK TO THE UTILITY FOR ALL STATES SERVED(MWh)","TRANSPORTATION ELECTRIC ENERGY SOLD BACK TO THE UTILITY FOR ALL STATES SERVED(MWh)","TOTAL ELECTRIC ENERGY SOLD BACK TO THE UTILITY FOR ALL STATES SERVED(MWh)","RESIDENTIAL INSTALLED NET METERING CAPACITY FOR ALL STATES SERVED(MW)","COMMERCIAL INSTALLED NET METERING CAPACITY FOR ALL STATES SERVED(MW)","INDUSTRIAL INSTALLED NET METERING CAPACITY FOR ALL STATES SERVED(MW)","TRANSPORTATION INSTALLED NET METERING CAPACITY FOR ALL STATES SERVED(MW)","INSTALLED NET METERING CAPACITY FOR ALL STATES SERVED(MW)","RESIDENTIAL NET METERING CUSTOMER COUNT FOR ALL STATES SERVED","COMMERCIAL NET METERING CUSTOMER COUNT FOR ALL STATES SERVED","INDUSTRIAL NET METERING CUSTOMER COUNT FOR ALL STATES SERVED","TRANSPORTATION NET METERING CUSTOMER COUNT FOR ALL STATES SERVED","NET METERING CUSTOMER COUNT FOR ALL STATES SERVED"  

U.S. Energy Information Administration (EIA) Indexed Site

UTILITY FOR ALL STATES SERVED(MWh)","RESIDENTIAL INSTALLED NET METERING CAPACITY FOR ALL STATES SERVED(MW)","COMMERCIAL INSTALLED NET METERING CAPACITY FOR ALL STATES SERVED(MW)","INDUSTRIAL INSTALLED NET METERING CAPACITY FOR ALL STATES SERVED(MW)","TRANSPORTATION INSTALLED NET METERING CAPACITY FOR ALL STATES SERVED(MW)","INSTALLED NET METERING CAPACITY FOR ALL STATES SERVED(MW)","RESIDENTIAL NET METERING CUSTOMER COUNT FOR ALL STATES SERVED","COMMERCIAL NET METERING CUSTOMER COUNT FOR ALL STATES SERVED","INDUSTRIAL NET METERING CUSTOMER COUNT FOR ALL STATES SERVED","TRANSPORTATION NET METERING CUSTOMER COUNT FOR ALL STATES SERVED","NET METERING CUSTOMER COUNT FOR ALL STATES SERVED"

495

High Dielectric Dummy Loads for ITER ICRH Antenna Laboratory Testing: Numerical Simulation of One Triplet Loading by Ferroelectric Ceramics  

SciTech Connect

Up to now, classical 'water' loads have been used for low power testing of ITER ICRH prototype or mock-up antennas . A fair description of the antenna frequency response is obtained excepted for the phasing (0 {pi} 0 {pi}). High dielectric loads are requested to improve the antenna response in the low frequency band. In view of laboratory testing, dummy loads are also required to have efficient wave spatial attenuation to avoid standing waves and to minimize load