Sample records for liquid butane liquid

  1. Liquid-Liquid Extraction Processes

    E-Print Network [OSTI]

    Fair, J. R.; Humphrey, J. L.

    1983-01-01T23:59:59.000Z

    Liquid-liquid extraction is the separation of one or more components of a liquid solution by contact with a second immiscible liquid called the solvent. If the components in the original liquid solution distribute themselves differently between...

  2. Liquid electrode

    DOE Patents [OSTI]

    Ekechukwu, Amy A. (Augusta, GA)

    1994-01-01T23:59:59.000Z

    A dropping electrolyte electrode for use in electrochemical analysis of non-polar sample solutions, such as benzene or cyclohexane. The liquid electrode, preferably an aqueous salt solution immiscible in the sample solution, is introduced into the solution in dropwise fashion from a capillary. The electrolyte is introduced at a known rate, thus, the droplets each have the same volume and surface area. The electrode is used in making standard electrochemical measurements in order to determine properties of non-polar sample solutions.

  3. Liquid electrode

    DOE Patents [OSTI]

    Ekechukwu, A.A.

    1994-07-05T23:59:59.000Z

    A dropping electrolyte electrode is described for use in electrochemical analysis of non-polar sample solutions, such as benzene or cyclohexane. The liquid electrode, preferably an aqueous salt solution immiscible in the sample solution, is introduced into the solution in dropwise fashion from a capillary. The electrolyte is introduced at a known rate, thus, the droplets each have the same volume and surface area. The electrode is used in making standard electrochemical measurements in order to determine properties of non-polar sample solutions. 2 figures.

  4. Liquid foams of graphene

    E-Print Network [OSTI]

    Alcazar Jorba, Daniel

    2012-01-01T23:59:59.000Z

    Liquid foams are dispersions of bubbles in a liquid. Bubbles are stabilized by foaming agents that position at the interface between the gas and the liquid. Most foaming agents, such as the commonly used sodium dodecylsulfate, ...

  5. Safetygram #9- Liquid Hydrogen

    Broader source: Energy.gov [DOE]

    Hydrogen is colorless as a liquid. Its vapors are colorless, odorless, tasteless, and highly flammable.

  6. Liquid Hydrogen Absorber for MICE

    E-Print Network [OSTI]

    Ishimoto, S.

    2010-01-01T23:59:59.000Z

    REFERENCES Figure 5: Liquid hydrogen absorber and test6: Cooling time of liquid hydrogen absorber. Eight CernoxLIQUID HYDROGEN ABSORBER FOR MICE S. Ishimoto, S. Suzuki, M.

  7. Equation for liquid density

    SciTech Connect (OSTI)

    Yaws, C.L.; Yang, H.C.; Hopper, J.R.; Cawley, W.A. (Lamar Univ., Beaumont, TX (US))

    1991-01-01T23:59:59.000Z

    Saturated liquid densities for organic chemicals are given as functions of temperature using a modified Rackett equation.

  8. Liquid detection circuit

    DOE Patents [OSTI]

    Regan, Thomas O. (North Aurora, IL)

    1987-01-01T23:59:59.000Z

    Herein is a circuit which is capable of detecting the presence of liquids, especially cryogenic liquids, and whose sensor will not overheat in a vacuum. The circuit parameters, however, can be adjusted to work with any liquid over a wide range of temperatures.

  9. Radiation monitor for liquids

    DOE Patents [OSTI]

    Koster, J.E.; Bolton, R.D.

    1999-03-02T23:59:59.000Z

    A radiation monitor for use with liquids that utilizes air ions created by alpha radiation emitted by the liquids as its detectable element. A signal plane, held at an electrical potential with respect to ground, collects these air ions. A guard plane or guard rings is used to limit leakage currents. In one embodiment, the monitor is used for monitoring liquids retained in a tank. Other embodiments monitor liquids flowing through a tank, and bodies of liquids, such as ponds, lakes, rivers and oceans. 4 figs.

  10. Radiation monitor for liquids

    DOE Patents [OSTI]

    Koster, James E. (Los Alamos, NM); Bolton, Richard D. (Los Alamos, NM)

    1999-01-01T23:59:59.000Z

    A radiation monitor for use with liquids that utilizes air ions created by alpha radiation emitted by the liquids as its detectable element. A signal plane, held at an electrical potential with respect to ground, collects these air ions. A guard plane or guard rings is used to limit leakage currents. In one embodiment, the monitor is used for monitoring liquids retained in a tank. Other embodiments monitor liquids flowing through a tank, and bodies of liquids, such as ponds, lakes, rivers and oceans.

  11. Liquid Wall Chambers

    SciTech Connect (OSTI)

    Meier, W R

    2011-02-24T23:59:59.000Z

    The key feature of liquid wall chambers is the use of a renewable liquid layer to protect chamber structures from target emissions. Two primary options have been proposed and studied: wetted wall chambers and thick liquid wall (TLW) chambers. With wetted wall designs, a thin layer of liquid shields the structural first wall from short ranged target emissions (x-rays, ions and debris) but not neutrons. Various schemes have been proposed to establish and renew the liquid layer between shots including flow-guiding porous fabrics (e.g., Osiris, HIBALL), porous rigid structures (Prometheus) and thin film flows (KOYO). The thin liquid layer can be the tritium breeding material (e.g., flibe, PbLi, or Li) or another liquid metal such as Pb. TLWs use liquid jets injected by stationary or oscillating nozzles to form a neutronically thick layer (typically with an effective thickness of {approx}50 cm) of liquid between the target and first structural wall. In addition to absorbing short ranged emissions, the thick liquid layer degrades the neutron flux and energy reaching the first wall, typically by {approx}10 x x, so that steel walls can survive for the life of the plant ({approx}30-60 yrs). The thick liquid serves as the primary coolant and tritium breeding material (most recent designs use flibe, but the earliest concepts used Li). In essence, the TLW places the fusion blanket inside the first wall instead of behind the first wall.

  12. Liquid Metal Transformers

    E-Print Network [OSTI]

    Sheng, Lei; Liu, Jing

    2014-01-01T23:59:59.000Z

    The room temperature liquid metal is quickly emerging as an important functional material in a variety of areas like chip cooling, 3D printing or printed electronics etc. With diverse capabilities in electrical, thermal and flowing behaviors, such fluid owns many intriguing properties that had never been anticipated before. Here, we show a group of unconventional phenomena occurring on the liquid metal objects. Through applying electrical field on the liquid metals immersed in water, a series of complex transformation behaviors such as self-assembling of a sheet of liquid metal film into a single sphere, quick mergences of separate metal droplets, controlled self-rotation and planar locomotion of liquid metal objects can be realized. Meanwhile, it was also found that two accompanying water vortexes were induced and reliably swirled near the rotating liquid metal sphere. Further, effects of the shape, size, voltage, orientation and geometries of the electrodes to control the liquid metal transformers were clar...

  13. Liquid level detector

    DOE Patents [OSTI]

    Tshishiku, Eugene M. (Augusta, GA)

    2011-08-09T23:59:59.000Z

    A liquid level detector for conductive liquids for vertical installation in a tank, the detector having a probe positioned within a sheath and insulated therefrom by a seal so that the tip of the probe extends proximate to but not below the lower end of the sheath, the lower end terminating in a rim that is provided with notches, said lower end being tapered, the taper and notches preventing debris collection and bubble formation, said lower end when contacting liquid as it rises will form an airtight cavity defined by the liquid, the interior sheath wall, and the seal, the compression of air in the cavity preventing liquid from further entry into the sheath and contact with the seal. As a result, the liquid cannot deposit a film to form an electrical bridge across the seal.

  14. (Ionization in liquids)

    SciTech Connect (OSTI)

    Not Available

    1991-01-01T23:59:59.000Z

    This document describes charge transport following ionization of model liquids and how this process may be important in carcinogenesis. 15 refs., 2 figs., 4 tabs. (MHB)

  15. Ultrasonic liquid level detector

    DOE Patents [OSTI]

    Kotz, Dennis M. (North Augusta, SC); Hinz, William R. (Augusta, GA)

    2010-09-28T23:59:59.000Z

    An ultrasonic liquid level detector for use within a shielded container, the detector being tubular in shape with a chamber at its lower end into which liquid from in the container may enter and exit, the chamber having an ultrasonic transmitter and receiver in its top wall and a reflector plate or target as its bottom wall whereby when liquid fills the chamber a complete medium is then present through which an ultrasonic wave may be transmitted and reflected from the target thus signaling that the liquid is at chamber level.

  16. Liquid Metal Transformers

    E-Print Network [OSTI]

    Lei Sheng; Jie Zhang; Jing Liu

    2014-01-30T23:59:59.000Z

    The room temperature liquid metal is quickly emerging as an important functional material in a variety of areas like chip cooling, 3D printing or printed electronics etc. With diverse capabilities in electrical, thermal and flowing behaviors, such fluid owns many intriguing properties that had never been anticipated before. Here, we show a group of unconventional phenomena occurring on the liquid metal objects. Through applying electrical field on the liquid metals immersed in water, a series of complex transformation behaviors such as self-assembling of a sheet of liquid metal film into a single sphere, quick mergences of separate metal droplets, controlled self-rotation and planar locomotion of liquid metal objects can be realized. Meanwhile, it was also found that two accompanying water vortexes were induced and reliably swirled near the rotating liquid metal sphere. Further, effects of the shape, size, voltage, orientation and geometries of the electrodes to control the liquid metal transformers were clarified. Such events are hard to achieve otherwise on rigid metal or conventional liquid spheres. This finding has both fundamental and practical significances which suggest a generalized way of making smart soft machine, collecting discrete metal fluids, as well as flexibly manipulating liquid metal objects including accompanying devices.

  17. Liquid Crystal Optofluidics

    SciTech Connect (OSTI)

    Vasdekis, Andreas E.; Cuennet, J. G.; Psaltis, D.

    2012-10-11T23:59:59.000Z

    By employing anisotropic fluids and namely liquid crystals, fluid flow becomes an additional degree of freedom in designing optofluidic devices. In this paper, we demonstrate optofluidic liquid crystal devices based on the direct flow of nematic liquid crystals in microfluidic channels. Contrary to previous reports, in the present embodiment we employ the effective phase delay acquired by light travelling through flowing liquid crystal, without analysing the polarisation state of the transmitted light. With this method, we demonstrate the variation in the diffraction pattern of an array of microfluidic channels acting as a grating. We also discuss our recent activities in integrating mechanical oscillators for on-chip peristaltic pumping.

  18. Scalability of mass transfer in liquid-liquid flow

    E-Print Network [OSTI]

    Woitalka, A.

    We address liquid–liquid mass transfer between immiscible liquids using the system 1-butanol and water, with succinic acid as the mass transfer component. Using this system we evaluate the influence of two-phase flow ...

  19. INEEL Liquid Effluent Inventory

    SciTech Connect (OSTI)

    Major, C.A.

    1997-06-01T23:59:59.000Z

    The INEEL contractors and their associated facilities are required to identify all liquid effluent discharges that may impact the environment at the INEEL. This liquid effluent information is then placed in the Liquid Effluent Inventory (LEI) database, which is maintained by the INEEL prime contractor. The purpose of the LEI is to identify and maintain a current listing of all liquid effluent discharge points and to identify which discharges are subject to federal, state, or local permitting or reporting requirements and DOE order requirements. Initial characterization, which represents most of the INEEL liquid effluents, has been performed, and additional characterization may be required in the future to meet regulations. LEI information is made available to persons responsible for or concerned with INEEL compliance with liquid effluent permitting or reporting requirements, such as the National Pollutant Discharge Elimination System, Wastewater Land Application, Storm Water Pollution Prevention, Spill Prevention Control and Countermeasures, and Industrial Wastewater Pretreatment. The State of Idaho Environmental Oversight and Monitoring Program also needs the information for tracking liquid effluent discharges at the INEEL. The information provides a baseline from which future liquid discharges can be identified, characterized, and regulated, if appropriate. The review covered new and removed buildings/structures, buildings/structures which most likely had new, relocated, or removed LEI discharge points, and at least 10% of the remaining discharge points.

  20. Synthesis of ionic liquids

    DOE Patents [OSTI]

    Dai, Sheng [Knoxville, TN; Luo, Huimin [Knoxville, TN

    2008-09-09T23:59:59.000Z

    Ionic compounds which are liquids at room temperature are formed by the method of mixing a neutral organic liqand with the salt of a metal cation and its conjugate anion. The liquids are hydrophobic, conductive and stable and have uses as solvents and in electrochemical devices.

  1. Synthesis of ionic liquids

    DOE Patents [OSTI]

    Dai, Sheng (Knoxville, TN); Luo, Huimin (Knoxville, TN)

    2011-11-01T23:59:59.000Z

    Ionic compounds which are liquids at room temperature are formed by the method of mixing a neutral organic ligand with the salt of a metal cation and its conjugate anion. The liquids are hydrophobic, conductive and stable and have uses as solvents and in electrochemical devices.

  2. Liquid heat capacity lasers

    DOE Patents [OSTI]

    Comaskey, Brian J. (Walnut Creek, CA); Scheibner, Karl F. (Tracy, CA); Ault, Earl R. (Livermore, CA)

    2007-05-01T23:59:59.000Z

    The heat capacity laser concept is extended to systems in which the heat capacity lasing media is a liquid. The laser active liquid is circulated from a reservoir (where the bulk of the media and hence waste heat resides) through a channel so configured for both optical pumping of the media for gain and for light amplification from the resulting gain.

  3. Liquid sampling system

    DOE Patents [OSTI]

    Larson, L.L.

    1984-09-17T23:59:59.000Z

    A conduit extends from a reservoir through a sampling station and back to the reservoir in a closed loop. A jet ejector in the conduit establishes suction for withdrawing liquid from the reservoir. The conduit has a self-healing septum therein upstream of the jet ejector for receiving one end of a double-ended cannula, the other end of which is received in a serum bottle for sample collection. Gas is introduced into the conduit at a gas bleed between the sample collection bottle and the reservoir. The jet ejector evacuates gas from the conduit and the bottle and aspirates a column of liquid from the reservoir at a high rate. When the withdrawn liquid reaches the jet ejector the rate of flow therethrough reduces substantially and the gas bleed increases the pressure in the conduit for driving liquid into the sample bottle, the gas bleed forming a column of gas behind the withdrawn liquid column and interrupting the withdrawal of liquid from the reservoir. In the case of hazardous and toxic liquids, the sample bottle and the jet ejector may be isolated from the reservoir and may be further isolated from a control station containing remote manipulation means for the sample bottle and control valves for the jet ejector and gas bleed. 5 figs.

  4. Liquid sampling system

    DOE Patents [OSTI]

    Larson, Loren L. (Idaho Falls, ID)

    1987-01-01T23:59:59.000Z

    A conduit extends from a reservoir through a sampling station and back to the reservoir in a closed loop. A jet ejector in the conduit establishes suction for withdrawing liquid from the reservoir. The conduit has a self-healing septum therein upstream of the jet ejector for receiving one end of a double-ended cannula, the other end of which is received in a serum bottle for sample collection. Gas is introduced into the conduit at a gas bleed between the sample collection bottle and the reservoir. The jet ejector evacuates gas from the conduit and the bottle and aspirates a column of liquid from the reservoir at a high rate. When the withdrawn liquid reaches the jet ejector the rate of flow therethrough reduces substantially and the gas bleed increases the pressure in the conduit for driving liquid into the sample bottle, the gas bleed forming a column of gas behind the withdrawn liquid column and interrupting the withdrawal of liquid from the reservoir. In the case of hazardous and toxic liquids, the sample bottle and the jet ejector may be isolated from the reservoir and may be further isolated from a control station containing remote manipulation means for the sample bottle and control valves for the jet ejector and gas bleed.

  5. Electrically Deformable Liquid Marbles

    E-Print Network [OSTI]

    Edward Bormashenko; Roman Pogreb; Tamir Stein; Gene Whyman; Marcelo Schiffer; Doron Aurbach

    2011-02-17T23:59:59.000Z

    Liquid marbles, which are droplets coated with a hydrophobic powder, were exposed to a uniform electric field. It was established that a threshold value of the electric field, 15 cgse, should be surmounted for deformation of liquid marbles. The shape of the marbles was described as a prolate spheroid. The semi-quantitative theory describing deformation of liquid marbles in a uniform electric field is presented. The scaling law relating the radius of the contact area of the marble to the applied electric field shows a satisfactory agreement with the experimental data.

  6. Liquid metal electric pump

    DOE Patents [OSTI]

    Abbin, J.P.; Andraka, C.E.; Lukens, L.L.; Moreno, J.B.

    1992-01-14T23:59:59.000Z

    An electrical pump for pumping liquid metals to high pressures in high temperature environments without the use of magnets or moving mechanical parts. The pump employs a non-porous solid electrolyte membrane, typically ceramic, specific to the liquid metal to be pumped. A DC voltage is applied across the thickness of the membrane causing ions to form and enter the membrane on the electrically positive surface, with the ions being neutralized on the opposite surface. This action provides pumping of the liquid metal from one side of the non-porous solid electrolyte membrane to the other. 3 figs.

  7. Liquid metal electric pump

    DOE Patents [OSTI]

    Abbin, Joseph P. (Albuquerque, NM); Andraka, Charles E. (Albuquerque, NM); Lukens, Laurance L. (Albuquerque, NM); Moreno, James B. (Albuquerque, NM)

    1992-01-01T23:59:59.000Z

    An electrical pump for pumping liquid metals to high pressures in high temperature environments without the use of magnets or moving mechanical parts. The pump employs a non-porous solid electrolyte membrane, typically ceramic, specific to the liquid metal to be pumped. A DC voltage is applied across the thickness of the membrane causing ions to form and enter the membrane on the electrically positive surface, with the ions being neutralized on the opposite surface. This action provides pumping of the liquid metal from one side of the non-porous solid electrolyte membrane to the other.

  8. Liquid Phase Heating Systems

    E-Print Network [OSTI]

    Mordt, E. H.

    1979-01-01T23:59:59.000Z

    Temperature Water (HTW) central district heating systems are far superior to steam systems in large, spread out installations such as airports, universities and office complexes. Water, pressurized to keep it in the liquid state, is distributed at 400o...

  9. Liquidity facilities and signaling

    E-Print Network [OSTI]

    Arregui, Nicolás

    2010-01-01T23:59:59.000Z

    This dissertation studies the role of signaling concerns in discouraging access to liquidity facilities like the IMF contingent credit lines (CCL) and the Discount Window (DW). In Chapter 1, I analyze the introduction of ...

  10. Liquid crystalline composites containing phyllosilicates

    DOE Patents [OSTI]

    Chaiko, David J.

    2004-07-13T23:59:59.000Z

    The present invention provides phyllosilicate-polymer compositions which are useful as liquid crystalline composites. Phyllosilicate-polymer liquid crystalline compositions of the present invention can contain a high percentage of phyllosilicate while at the same time be transparent. Because of the ordering of the particles liquid crystalline composite, liquid crystalline composites are particularly useful as barriers to gas transport.

  11. Liquid mixing device

    SciTech Connect (OSTI)

    O'Leary, R. P.

    1985-08-06T23:59:59.000Z

    A mixing device for mixing at least two liquids to produce a homogenous mixture. The device includes an elongated chamber in which a vertically oriented elongated mixing cavity is located. The cavity is sealed at its lower end and it is open at its upper end and in communication with the interior of the chamber. An elongated conduit extends the length of the cavity and is adapted to receive liquids to be mixed. The conduit includes a plurality of ports located at longitudinally spaced positions therealong and which ports are directed in different directions. The ports create plural streams of liquid which interact and mix with one another within the cavity. The mixed liquids overflow the cavity and out its top end into the chamber 24. The chamber 24 includes an outlet from which the mixed liquids are withdrawn. In accordance with the preferred embodiment gas eductor means are provided in the inlet to the conduit to introduce gas bubbles within the cavity. Gas vent means are also provided in the device to vent any introduced gases from the device so that only the mixed liquids flow out the outlet.

  12. liquid nberwp.tex Liquidity Constraints and Precautionary Saving

    E-Print Network [OSTI]

    Niebur, Ernst

    liquid nberwp.tex Liquidity Constraints and Precautionary Saving Christopher D. Carroll ccarroll to the optimal consumption/saving problem under uncertainty have long known that there are quantitatively important in- teractions between liquidity constraints and precautionary saving behavior. This paper

  13. Properties of Liquid Plutonium

    SciTech Connect (OSTI)

    Freibert, Franz J. [Los Alamos National Laboratory; Mitchell, Jeremy N. [Los Alamos National Laboratory; Schwartz, Daniel S. [Los Alamos National Laboratory; Saleh, Tarik A. [Los Alamos National Laboratory; Migliori, Albert [Los Alamos National Laboratory

    2012-08-02T23:59:59.000Z

    Unalloyed polycrystalline Pu displays extreme thermal expansion behavior, i.e., {alpha} {yields} {beta} {yields} {gamma} {yields} {delta} increases by 25% in volume and {delta} {yields} {var_epsilon} {yields} liquid decreases by 4.5% in volume. Thus, making it difficult to measure density into the liquid state. Dilatometer outfitted with CaF molten metal cell offers a proven capability to measure thermal expansion in molten metals, but has yet to be proven for Pu. Historic data from the liquid nuclear fuels program will prove extremely useful as a guide to future measurements. 3.3at% Ga changes Pu molten metal properties: 50% increase in viscosity and {approx}3% decrease in density. Fe may decrease the density by a small amount assuming an averaging of densities for Pu-Ga and Pu-Fe liquids. More recent Boivineau (2009) work needs some interpretation, but technique is being employed in (U,Pu)O{sub 2} nuclear fuels program (Pu Futures, 2012).

  14. Breakup of Liquid Filaments

    E-Print Network [OSTI]

    Castrejon-Pita, Alfonso A.; Castrejon-Pita, J.R.; Hutchings, I.M.

    2012-01-01T23:59:59.000Z

    , including the dispersion of liquid drugs into res- pirable droplets, microfluidics, crop- and paint-spraying, and ink-jet printing [2–4]. There are also biological sys- tems in which either long filaments remain intact, or many droplets are formed [5, 6...

  15. Imaging Liquids Using Microfluidic Cells

    SciTech Connect (OSTI)

    Yu, Xiao-Ying; Liu, Bingwen; Yang, Li

    2013-05-10T23:59:59.000Z

    Chemistry occurring in the liquid and liquid surface is important in many applications. Chemical imaging of liquids using vacuum based analytical techniques is challenging due to the difficulty in working with liquids with high volatility. Recent development in microfluidics enabled and increased our capabilities to study liquid in situ using surface sensitive techniques such as electron microscopy and spectroscopy. Due to its small size, low cost, and flexibility in design, liquid cells based on microfluidics have been increasingly used in studying and imaging complex phenomena involving liquids. This paper presents a review of microfluidic cells that were developed to adapt to electron microscopes and various spectrometers for in situ chemical analysis and imaging of liquids. The following topics will be covered including cell designs, fabrication techniques, unique technical features for vacuum compatible cells, and imaging with electron microscopy and spectroscopy. Challenges are summarized and recommendations for future development priority are proposed.

  16. Liquid crystalline composites containing phyllosilicates

    DOE Patents [OSTI]

    Chaiko; David J. (Naperville, IL)

    2007-05-08T23:59:59.000Z

    The present invention provides barrier films having reduced gas permeability for use in packaging and coating applications. The barrier films comprise an anisotropic liquid crystalline composite layer formed from phyllosilicate-polymer compositions. Phyllosilicate-polymer liquid crystalline compositions of the present invention can contain a high percentage of phyllosilicate while remaining transparent. Because of the ordering of the particles in the liquid crystalline composite, barrier films comprising liquid crystalline composites are particularly useful as barriers to gas transport.

  17. High temperature liquid level sensor

    DOE Patents [OSTI]

    Tokarz, Richard D. (West Richland, WA)

    1983-01-01T23:59:59.000Z

    A length of metal sheathed metal oxide cable is perforated to permit liquid access to the insulation about a pair of conductors spaced close to one another. Changes in resistance across the conductors will be a function of liquid level, since the wetted insulation will have greater electrical conductivity than that of the dry insulation above the liquid elevation.

  18. Factors influencing quantitative liquid (scanning) transmission...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Factors influencing quantitative liquid (scanning) transmission electron microscopy. Factors influencing quantitative liquid (scanning) transmission electron microscopy. Abstract:...

  19. Analysis & Simulation of Dynamics in Supercooled Liquids

    E-Print Network [OSTI]

    Elmatad, Yael Sarah

    2011-01-01T23:59:59.000Z

    Moreover, the heat capacity of that liquid is also higherthe intensive heat capacities of the liquid and the crystal,

  20. Modeling Liquid-Liquid Equilibrium of Ionic Liquid Systems with NRTL, Electrolyte-NRTL, and UNIQUAC

    E-Print Network [OSTI]

    Stadtherr, Mark A.

    Modeling Liquid-Liquid Equilibrium of Ionic Liquid Systems with NRTL, Electrolyte-NRTL, and UNIQUAC different excess Gibbs free energy models are evaluated: the NRTL, UNIQUAC and electrolyte- NRTL (eNRTL) models. In the case of eNRTL, a new formulation of the model is used, based on a symmetric reference

  1. Help cut pollution with vapor/liquid and liquid/liquid separators

    SciTech Connect (OSTI)

    Woinsky, S.G.

    1994-10-01T23:59:59.000Z

    Vapor/liquid and liquid/liquid separators are common in chemical process industries plants. In addition to separating phases, these devices can aid in reducing pollution in the plant. Two-phase separators achieve pollution prevention via recycling of intermediates and final products. It is doubtful that most vapor/liquid and liquid/liquid separators are used specifically for pollution prevention projects. They may have another purpose yet provide pollution prevention as a bonus. The first step in achieving pollution prevention by design is for operating companies to be aware of vapor/liquid and liquid/liquid separators as potential pollution prevention devices. Then, likely applications need to be investigated. Since the quantities of material recovered are relatively small, higher value products are the most likely targets, especially for liquid/liquid separators. However, for vapor/liquid separators, the costs involved are usually relatively low since only the cost of a separator pad is normally involved, and more moderately valued products can be targets.

  2. Liquid filtration simulation

    SciTech Connect (OSTI)

    Corey, I.; Bergman, W.

    1996-06-01T23:59:59.000Z

    We have a developed a computer code that simulates 3-D filtration of suspended particles in fluids in realistic filter structures. This code, being the most advanced filtration simulation package developed to date, provides LLNL and DOE with new capabilities to address problems in cleaning liquid wastes, medical fluid cleaning, and recycling liquids. The code is an integrated system of commercially available and LLNL-developed software; the most critical are the computational fluid dynamics (CFD) solver and the particle transport program. For the CFD solver, we used a commercial package based on Navier-Stokes equations and a LLNL-developed package based on Boltzman-lattice gas equations. For the particle transport program, we developed a cod based on the 3-D Langevin equation of motion and the DLVO theory of electrical interactions. A number of additional supporting packages were purchased or developed to integrate the simulation tasks and to provide visualization output.

  3. Schrodinger Fermi Liquids

    E-Print Network [OSTI]

    Wang, Juven

    2013-01-01T23:59:59.000Z

    We study a class of strongly interacting many-body fermionic systems in 2+1D non-relativistic conformal field theory via holography. The 5D charged black hole with asymptotic Schrodinger isometry in the bulk gravity side introduces parameters of background density and finite particle number into the boundary field theory. We propose the holographic dictionary, and realize a quantum phase transition of this fermionic liquid with fixed particle number by tuning the background density $\\beta$ at zero temperature. On the larger $\\beta$ side, we find the signal of a sharp quasiparticle pole on the spectral function A(k,w), indicating a well-defined Fermi surface. On the smaller $\\beta$ side, we find only a hump with no sharp peak for A(k,w), indicating the disappearance of Fermi surface. The dynamical exponent $z$ of quasiparticle dispersion goes from being Fermi-liquid-like $z\\simeq1$ scaling at larger $\\beta$ to a non-Fermi-liquid scaling $z\\simeq 3/2$ at smaller $\\beta$. By comparing the structure of Green's fu...

  4. Liquid class predictor for liquid handling of complex mixtures

    DOE Patents [OSTI]

    Seglke, Brent W. (San Ramon, CA); Lekin, Timothy P. (Livermore, CA)

    2008-12-09T23:59:59.000Z

    A method of establishing liquid classes of complex mixtures for liquid handling equipment. The mixtures are composed of components and the equipment has equipment parameters. The first step comprises preparing a response curve for the components. The next step comprises using the response curve to prepare a response indicator for the mixtures. The next step comprises deriving a model that relates the components and the mixtures to establish the liquid classes.

  5. Portable liquid collection electrostatic precipitator

    DOE Patents [OSTI]

    Carlson, Duane C.; DeGange, John J.; Halverson, Justin E.

    2005-10-18T23:59:59.000Z

    A portable liquid collection electrostatic collection precipitator for analyzing air is provided which is a relatively small, self-contained device. The device has a tubular collection electrode, a reservoir for a liquid, and a pump. The pump pumps the liquid into the collection electrode such that the liquid flows down the exterior of the collection electrode and is recirculated to the reservoir. An air intake is provided such that air to be analyzed flows through an ionization section to ionize analytes in the air, and then flows near the collection electrode where ionized analytes are collected. A portable power source is connected to the air intake and the collection electrode. Ionizable constituents in the air are ionized, attracted to the collection electrode, and precipitated in the liquid. The precipitator may also have an analyzer for the liquid and may have a transceiver allowing remote operation and data collection.

  6. Liquid monobenzoxazine based resin system

    DOE Patents [OSTI]

    Tietze, Roger; Nguyen, Yen-Loan; Bryant, Mark

    2014-10-07T23:59:59.000Z

    The present invention provides a liquid resin system including a liquid monobenzoxazine monomer and a non-glycidyl epoxy compound, wherein the weight ratio of the monobenzoxazine monomer to the non-glycidyl epoxy compound is in a range of about 25:75 to about 60:40. The liquid resin system exhibits a low viscosity and exceptional stability over an extended period of time making its use in a variety of composite manufacturing methods highly advantageous.

  7. Supported liquid membrane electrochemical separators

    DOE Patents [OSTI]

    Pemsler, J. Paul (Lexington, MA); Dempsey, Michael D. (Revere, MA)

    1986-01-01T23:59:59.000Z

    Supported liquid membrane separators improve the flexibility, efficiency and service life of electrochemical cells for a variety of applications. In the field of electrochemical storage, an alkaline secondary battery with improved service life is described in which a supported liquid membrane is interposed between the positive and negative electrodes. The supported liquid membranes of this invention can be used in energy production and storage systems, electrosynthesis systems, and in systems for the electrowinning and electrorefining of metals.

  8. Process for preparing liquid wastes

    DOE Patents [OSTI]

    Oden, Laurance L. (Albany, OR); Turner, Paul C. (Albany, OR); O'Connor, William K. (Lebanon, OR); Hansen, Jeffrey S. (Corvallis, OR)

    1997-01-01T23:59:59.000Z

    A process for preparing radioactive and other hazardous liquid wastes for treatment by the method of vitrification or melting is provided for.

  9. Liquid crystal polyester thermosets

    DOE Patents [OSTI]

    Benicewicz, Brian C. (Los Alamos, NM); Hoyt, Andrea E. (Los Alamos, NM)

    1992-01-01T23:59:59.000Z

    The present invention provides (1) curable liquid crystalline polyester monomers represented by the formula: R.sup.1 --A.sup.1 --B.sup.1 --A.sup.2 --B.sup.2 --A.sup.3 --R.sup.2 where R.sup.1 and R.sup.2 are radicals selected from the group consisting of maleimide, substituted maleimide, nadimide, substituted naimide, ethynyl, and (C(R.sup.3).sub.2).sub.2 where R.sup.3 is hydrogen with the proviso that the two carbon atoms of (C(R.sup.3).sub.2).sub.2 are bound on the aromatic ring of A.sup.1 or A.sup.3 to adjacent carbon atoms, A.sup.1 and A.sup.3 are 1,4-phenylene and the same where said group contains one or more substituents selected from the group consisting of halo, e.g., fluoro, chloro, bromo, or iodo, nitro lower alkyl, e.g., methyl, ethyl, or propyl, alkoxy, e.g., methoxy, ethoxy, or propoxy, and fluoroalkyl, e.g., trifluoromethyl, pentafluoroethyl and the like, A.sup.2 is selected from the group consisting of 1,4-phenylene, 4,4'-biphenyl, 2,6-naphthylene and the same where said groups contain one or more substituents selected from the group consisting of halo, e.g., fluoro, chloro, bromo, or iodo, nitro, lower alkyl, e.g., methyl, ethyl, and propyl, lower alkoxy, e.g., methoxy, ethoxy, or propoxy, and fluoroalkyl or fluoroalkoxy, e.g., trifluoromethyl, pentafluoroethyl and the like, and B.sup.1 and B.sup.2 are selected from the group consisting of --C(O)--O-- and --O--C(O)--, (2) thermoset liquid crystalline polyester compositions comprised of heat-cured segments derived from monomers represented by the formula: R.sup.1 --A.sup.1 --B.sup.1 --A.sup.2 --B.sup.2 --A.sup.3 --R.sup.2 as described above, (3) curable blends of at least two of the polyester monomers and (4) processes of preparing the curable liquid crystalline polyester monomers.

  10. Lithium-loaded liquid scintillators

    DOE Patents [OSTI]

    Dai, Sheng (Knoxville, TN); Kesanli, Banu (Mersin, TR); Neal, John S. (Knoxville, TN)

    2012-05-15T23:59:59.000Z

    The invention is directed to a liquid scintillating composition containing (i) one or more non-polar organic solvents; (ii) (lithium-6)-containing nanoparticles having a size of up to 10 nm and surface-capped by hydrophobic molecules; and (iii) one or more fluorophores. The invention is also directed to a liquid scintillator containing the above composition.

  11. Method for treating liquid wastes

    DOE Patents [OSTI]

    Katti, K.V.; Volkert, W.A.; Singh, P.; Ketring, A.R.

    1995-12-26T23:59:59.000Z

    The method of treating liquid waste in a media is accomplished by exposing the media to phosphinimines and sequestering {sup 99}Tc from the media by the phosphinimine (PN) functionalities. The system for treating the liquid waste in the media includes extraction of {sup 99}TcO{sub 4}{sup {minus}} from aqueous solutions into organic solvents or mixed organic/polar media, extraction of {sup 99}Tc from solutions on a solid matrix by using a container containing PN functionalities on solid matrices including an inlet and outlet for allowing flow of media through an immobilized phosphinimine ligand system contained within the container. Also, insoluble suspensions of phosphinimine functionalities on solid matrices in liquid solutions or present on supported liquid membranes (SLM) can be used to sequester {sup 99}Tc from those liquids. 6 figs.

  12. Method for treating liquid wastes

    DOE Patents [OSTI]

    Katti, Kattesh V. (Columbia, MO); Volkert, Wynn A. (Columbia, MO); Singh, Prahlad (Columbia, MO); Ketring, Alan R. (Columbia, MO)

    1995-01-01T23:59:59.000Z

    The method of treating liquid waste in a media is accomplished by exposing the media to phosphinimines and sequestering .sup.99 Tc from the media by the phosphinimine (PN) functionalities. The system for treating the liquid waste in the media includes extraction of .sup.99 TcO.sub.4.sup.- from aqueous solutions into organic solvents or mixed organic/polar media, extraction of .sup.99 Tc from solutions on a solid matrix by using a container containing PN functionalities on solid matrices including an inlet and outlet for allowing flow of media through an immobilized phosphinimine ligand system contained within the container. Also, insoluble suspensions of phosphinimine functionalities on solid matrices in liquid solutions or present on supported liquid membranes (SLM) can be used to sequester .sup.99 Tc from those liquids.

  13. Singular Limits in Polymer Stabilized Liquid Crystals

    E-Print Network [OSTI]

    1910-31-00T23:59:59.000Z

    We investigate equilibrium configurations for a polymer stabilized liquid crys- tal material ... eling the cross section of the liquid crystal-polymer fiber composite.

  14. Imaging Liquids Using Microfluidic Cells. | EMSL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    the difficulty in working with liquids with high volatility. Recent development in microfluidics enabled and increased our capabilities to study liquid in situ using surface...

  15. Liquid Hydrogen Delivery - Strategic Directions for Hydrogen...

    Broader source: Energy.gov (indexed) [DOE]

    Liquid Hydrogen Delivery - Strategic Directions for Hydrogen Delivery Workshop Liquid Hydrogen Delivery - Strategic Directions for Hydrogen Delivery Workshop Targets, barriers and...

  16. Solid-Liquid Interfacial Premelting

    E-Print Network [OSTI]

    Yang, Yang; Asta, Mark; Laird, Brian Bostian

    2013-02-28T23:59:59.000Z

    liquid-liquid miscibility gap, negligible solubility of Pb in the Al solid phase, and a large melting point separa- tion (600 K for Pb and 933 K for Al). We have previously reported results from MD simulations on this system at 625 K, a temperature just... undergoes a roughening transition about 100 K below the melting point of Al. Simulation details.—In our simulations of the Al-Pb solid-liquid interface, we employ a classical many-body potential developed by Landa et al. [42] to model the inter- atomic...

  17. Gaseous and Liquid Hydrogen Storage

    Broader source: Energy.gov [DOE]

    Today's state of the art for hydrogen storage includes 5,000- and 10,000-psi compressed gas tanks and cryogenic liquid hydrogen tanks for on-board hydrogen storage.

  18. Fluorescent optical liquid level sensor

    DOE Patents [OSTI]

    Weiss, Jonathan D. (Albuquerque, NM)

    2001-01-01T23:59:59.000Z

    A liquid level sensor comprising a transparent waveguide containing fluorescent material that is excited by light of a first wavelength and emits at a second, longer wavelength. The upper end of the waveguide is connected to a light source at the first wavelength through a beveled portion of the waveguide such that the input light is totally internally reflected within the waveguide above an air/liquid interface in a tank but is transmitted into the liquid below this interface. Light is emitted from the fluorescent material only in those portions of the waveguide that are above the air/liquid interface, to be collected at the upper end of the waveguide by a detector that is sensitive only to the second wavelength. As the interface moves down in the tank, the signal strength from the detector will increase.

  19. Liquid measurement - Techniques and problems

    SciTech Connect (OSTI)

    Caffey, B.R.

    1984-04-01T23:59:59.000Z

    This paper reviews a few liquid measurement techniques and their associated problems. In measuring liquid petroleum gas, the first obstacle to overcome is accomodating some form of volumetric measurement. This is usually accomplished by orifice, positive displacement, or turbine meters. Each of the three established methods is covered extensively by industry standards in the API Manual of Petroleum Standards. If the operator follows these standards, very accurate results can be achieved.

  20. Calculate viscosities for 355 liquids

    SciTech Connect (OSTI)

    Yaws, C.L.; Lin, Xiaoyan; Li Bu (Lamar Univ., TX (United States))

    1994-04-01T23:59:59.000Z

    Liquid viscosities are important factors in process design and operation. The viscosity of a liquid determines its flow properties, such as velocity and pressure drop. In addition, the heat- and mass-transfer characteristics of a liquid are affected by its viscosity. An equation can be used to calculate liquid viscosities as a function of temperature. In the accompanying table, regression coefficients are included for 355 compounds with five, six or seven carbon atoms--generally the most-widely used in the chemical and petroleum industries. To calculate the viscosity of a liquid at any temperature between its melting and critical points (T[sub min] and T[sub max]), use the following equation: log[sub 10] [eta][sub liq] = A + B/T + CT + DT[sup 2] where [eta][sub liq] = viscosity, cP, A,B,C and D = regression coefficients, and T = liquid temperature, K. Insert the temperature into the equation along with the corresponding regression coefficients from the table. The chemical formulae are listed by the number of carbon atoms.

  1. Adaptive Liquid Crystal Windows

    SciTech Connect (OSTI)

    Taheri, Bahman; Bodnar, Volodymyr

    2011-12-31T23:59:59.000Z

    Energy consumption by private and commercial sectors in the U.S. has steadily grown over the last decade. The uncertainty in future availability of imported oil, on which the energy consumption relies strongly, resulted in a dramatic increase in the cost of energy. About 20% of this consumption are used to heat and cool houses and commercial buildings. To reduce dependence on the foreign oil and cut down emission of greenhouse gases, it is necessary to eliminate losses and reduce total energy consumption by buildings. To achieve this goal it is necessary to redefine the role of the conventional windows. At a minimum, windows should stop being a source for energy loss. Ideally, windows should become a source of energy, providing net gain to reduce energy used to heat and cool homes. It is possible to have a net energy gain from a window if its light transmission can be dynamically altered, ideally electronically without the need of operator assistance, providing optimal control of the solar gain that varies with season and climate in the U.S. In addition, the window must not require power from the building for operation. Resolution of this problem is a societal challenge and of national interest and will have a broad global impact. For this purpose, the year-round, allclimate window solution to provide an electronically variable solar heat gain coefficient (SHGC) with a wide dynamic range is needed. AlphaMicron, Inc. (AMI) developed and manufactured 1ft × 1ft prototype panels for the world’s first auto-adjusting Adaptive Liquid Crystal Windows (ALCWs) that can operate from sunlight without the need for external power source and demonstrate an electronically adjustable SHGC. This novel windows are based on AlphaMicron’s patented e-Tint® technology, a guesthost liquid crystal system implemented on flexible, optically clear plastic films. This technology is suitable both for OEM and aftermarket (retro-fitting) lamination to new and existing windows. Low level of power consumption by ALCWs allows for on-board power electronics for automatic matching of transmission through windows to varying climate conditions without drawing the power from the power grid. ALCWs are capable of transmitting more sunlight in winters to assist in heating and less sunlight in summers to minimize overheating. As such, they can change the window from being a source of energy loss to a source of energy gain. In addition, the scalable AMI’s roll-to-roll process, proved by making 1ft × 1ftALCW prototype panels, allows for cost-effective production of large-scale window panels along with capability to change easily their color and shape. In addition to architectural glazing in houses and commercial buildings, ALCWs can be used in other applications where control of sunlight is needed, such as green houses, used by commercial produce growers and botanical gardens, cars, aircrafts, etc.

  2. Nanophosphor composite scintillator with a liquid matrix

    DOE Patents [OSTI]

    McKigney, Edward Allen (Los Alamos, NM); Burrell, Anthony Keiran (Los Alamos, NM); Bennett, Bryan L. (Los Alamos, NM); Cooke, David Wayne (Santa Fe, NM); Ott, Kevin Curtis (Los Alamos, NM); Bacrania, Minesh Kantilal (Los Alamos, NM); Del Sesto, Rico Emilio (Los Alamos, NM); Gilbertson, Robert David (Los Alamos, NM); Muenchausen, Ross Edward (Los Alamos, NM); McCleskey, Thomas Mark (Los Alamos, NM)

    2010-03-16T23:59:59.000Z

    An improved nanophosphor scintillator liquid comprises nanophosphor particles in a liquid matrix. The nanophosphor particles are optionally surface modified with an organic ligand. The surface modified nanophosphor particle is essentially surface charge neutral, thereby preventing agglomeration of the nanophosphor particles during dispersion in a liquid scintillator matrix. The improved nanophosphor scintillator liquid may be used in any conventional liquid scintillator application, including in a radiation detector.

  3. Liquid Cooling in Data Centers

    SciTech Connect (OSTI)

    Cader, Tahir; Sorell,, Vali; Westra, Levi; Marquez, Andres

    2009-05-01T23:59:59.000Z

    Semiconductor manufacturers have aggressively attacked the problem of escalating microprocessor power consumption levels. Today, server manufacturers can purchase microprocessors that currently have power consumption levels capped at 100W maximum. However, total server power levels continue to increase, with the increase in power consumption coming from the supportin chipsets, memory, and other components. In turn, full rack heat loads are very aggressivley climbing as well, and this is making it increasingly difficult and cost-prohibitive for facility owners to cool these high power racks. As a result, facilities owners are turning to alternative, and more energy efficient, cooling solutions that deploy liquids in one form or another. The paper discusses the advent of the adoption of liquid-cooling in high performance computing centers. An overview of the following competing rack-based, liquid-cooling, technologies is provided: in-row, above rack, refrigerated/enclosed rack, rear door heat exchanger, and device-level (i.e., chip-level). Preparation for a liquid-cooled data center, retroft and greenfield (new), is discussed, with a focus on the key issues that are common to all liquid-cooling technologies that depend upon the delivery of water to the rack (or in some deployments, a Coolant Distribution Unit). The paper then discusses, in some detail, the actual implementation and deployment of a liquid device-level cooled (spray cooled) supercomputer at the Pacific Northwest National Laboratory. Initial results from a successful 30 day compliance test show excellent hardware stability, operating system (OS) and software stack stability, application stability and performance, and an availability level that exceeded expectations at 99.94%. The liquid-cooled supercomputer achieved a peak performance of 9.287 TeraFlops, which placed it at number 101 in the June 2007 Top500 fastest supercomputers worldwide. Long-term performance and energy efficiency testing is currently underway, and detailed results will be reported in upcoming publications.

  4. Liquid membrane purification of biogas

    SciTech Connect (OSTI)

    Majumdar, S.; Guha, A.K.; Lee, Y.T.; Papadopoulos, T.; Khare, S. (Stevens Inst. of Tech., Hoboken, NJ (United States). Dept. of Chemistry and Chemical Engineering)

    1991-03-01T23:59:59.000Z

    Conventional gas purification technologies are highly energy intensive. They are not suitable for economic removal of CO{sub 2} from methane obtained in biogas due to the small scale of gas production. Membrane separation techniques on the other hand are ideally suited for low gas production rate applications due to their modular nature. Although liquid membranes possess a high species permeability and selectivity, they have not been used for industrial applications due to the problems of membrane stability, membrane flooding and poor operational flexibility, etc. A new hollow-fiber-contained liquid membrane (HFCLM) technique has been developed recently. This technique overcomes the shortcomings of the traditional immobilized liquid membrane technology. A new technique uses two sets of hydrophobic, microporous hollow fine fibers, packed tightly in a permeator shell. The inter-fiber space is filled with an aqueous liquid acting as the membrane. The feed gas mixture is separated by selective permeation of a species through the liquid from one fiber set to the other. The second fiber set carries a sweep stream, gas or liquid, or simply the permeated gas stream. The objectives (which were met) of the present investigation were as follows. To study the selective removal of CO{sub 2} from a model biogas mixture containing 40% CO{sub 2} (the rest being N{sub 2} or CH{sub 4}) using a HFCLM permeator under various operating modes that include sweep gas, sweep liquid, vacuum and conventional permeation; to develop a mathematical model for each mode of operation; to build a large-scale purification loop and large-scale permeators for model biogas separation and to show stable performance over a period of one month.

  5. Liquid-phase chromatography detector

    DOE Patents [OSTI]

    Voigtman, E.G.; Winefordner, J.D.; Jurgensen, A.R.

    1983-11-08T23:59:59.000Z

    A liquid-phase chromatography detector comprises a flow cell having an inlet tubular conduit for receiving a liquid chromatographic effluent and discharging it as a flowing columnar stream onto a vertically adjustable receiving surface spaced apart from and located vertically below and in close proximity to the discharge end of the tubular conduit; a receiver adapted to receive liquid overflowing from the receiving surface; an exit conduit for continuously removing liquid from the receiver; a light source for focusing fluorescence-producing light pulses on the flowing columnar stream as it passes from the outlet of the conduit to the receiving surface and a fluorescence detector to detect the produced fluorescence; a source of light pulse for producing acoustic waves in the columnar stream as it passes from the conduit outlet to the receiving surface; and a piezoelectric transducer adapted to detect those waves; and a source of bias voltage applied to the inlet tubular conduit and adapted to produce ionization of the liquid flowing through the flow cell so as to produce photocurrents therein and an electrical system to detect and record the photocurrents. This system is useful in separating and detecting individual chemical compounds from mixtures thereof. 5 figs.

  6. Are polar liquids less simple?

    E-Print Network [OSTI]

    D. Fragiadakis; C. M. Roland

    2012-08-28T23:59:59.000Z

    Strong correlation between equilibrium fluctuations of the potential energy, U, and the virial, W, is a characteristic of a liquid that implies the presence of certain dynamic properties, such as density scaling of the relaxation times and isochronal superpositioning of the relaxation function. In this work we employ molecular dynamics simulations (mds) on methanol and two variations, lacking hydrogen bonds and a dipole moment, to assess the connection between the correlation of U and W and these dynamic properties. We show, in accord with prior results of others [T.S. Ingebrigtsen, T.B. Schroder, J.C. Dyre, Phys. Rev. X 2, 011011 (2012).], that simple van der Waals liquids exhibit both strong correlations and the expected dynamic behavior. However, for polar liquids this correspondence breaks down - weaker correlation between U and W is not associated with worse conformance to density scaling or isochronal superpositioning. The reason for this is that strong correlation between U and W only requires their proportionality, whereas the expected dynamic behavior depends primarily on constancy of the proportionality constant for all state points. For hydrogen-bonded liquids, neither strong correlation nor adherence to the dynamic properties is observed; however, this nonconformance is not directly related to the concentration of hydrogen bonds, but rather to the greater deviation of the intermolecular potential from an inverse power law (IPL). Only (hypothetical) liquids having interactions governed strictly by an IPL are perfectly correlating and exhibit the consequent dynamic properties over all thermodynamic conditions.

  7. Fragmentation of suddenly heated liquids

    SciTech Connect (OSTI)

    Blink, J.A.

    1985-03-01T23:59:59.000Z

    Fragmentation of free liquids in Inertial Confinement Fusion reactors could determine the upper bound on reactor pulse rate. The x-ray ablated materials must cool and recondense to allow driver beam propagation. The increased surface area caused by fragmentation will enhance the cooling and condensation rates. Relaxation from the suddenly heated state will move a liquid into the negative pressure region under the liquid-vapor P-V dome. The lithium equation of state was used to demonstrate that neutron-induced vaporization uses only a minor fraction of the added heat, much less than would be required to drive the expansion. A 77% expansion of the lithium is required before the rapid vaporization process of spinodal decomposition could begin, and nucleation and growth are too slow to contribute to the expansion.

  8. Liquid soap film generates electricity

    E-Print Network [OSTI]

    Ahmad Amjadi; Sadegh Feiz; Reza Montazeri Namin

    2014-04-24T23:59:59.000Z

    We have observed that a rotating liquid soap film generates electricity when placed between two non-contact electrodes with a sufficiently large potential difference. In our experiments suspended liquid film (water + soap film) is formed on the surface of a circular frame, which is forced to rotate in the $x-y$ horizontal plane by a motor. This system is located at the center of two capacitor-like vertical plates to apply an external electric voltage difference in the $x-$direction. The produced electric current is collected from the liquid film using two conducting electrodes that are separated in the $y-$direction. We previously reported that a liquid film in an external electric field rotates when an electric current passes through it, naming it the liquid film motor (LFM). In this paper we report a novel technique, in which a similar device can be used as an electric generator, converting the rotating mechanical energy to electrical energy. The liquid film electric generator (LFEG) is in stark contrast to the LFM, both of which could be designed similarly in very small scales like micro scales with different applications. Although the device is comparable to commercial electric motors or electric generators, there is a significant difference in their working principles. Usually in an electric motor or generator the magnetic field causes the driving force, while in a LFM or LFEG the Coulomb force is the driving force. This fact is also interesting from the Bio-science point of view and brings a similarity to bio motors. Here we have investigated the electrical characteristics of such a generator for the first time experimentally and modelled the phenomenon with electroconvection governing equations. A numerical simulation is performed using the local approximation for the charge-potential relation and results are in qualitative agreement with experiments.

  9. Method of measuring a liquid pool volume

    DOE Patents [OSTI]

    Garcia, G.V.; Carlson, N.M.; Donaldson, A.D.

    1991-03-19T23:59:59.000Z

    A method of measuring a molten metal liquid pool volume and in particular molten titanium liquid pools is disclosed, including the steps of (a) generating an ultrasonic wave at the surface of the molten metal liquid pool, (b) shining a light on the surface of a molten metal liquid pool, (c) detecting a change in the frequency of light, (d) detecting an ultrasonic wave echo at the surface of the molten metal liquid pool, and (e) computing the volume of the molten metal liquid. 3 figures.

  10. New airport liquid analysis system undergoes testing at Albuquerque...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    New airport liquid analysis system New airport liquid analysis system undergoes testing at Albuquerque International Sunport A new tool that distinguishes potential-threat liquids...

  11. THERMODYNAMICS OF SOLID AND LIQUID GROUP III-V ALLOYS

    E-Print Network [OSTI]

    Anderson, T.J.

    2011-01-01T23:59:59.000Z

    a high temperature heat capacity for liquid gallium which isthe molar heat capacity of the stoichiometric liquid and theheat capacity of the supercooled stoichiometric binary liquid

  12. Stiffening solids with liquid inclusions

    E-Print Network [OSTI]

    Robert W. Style; Rostislav Boltyanskiy; Benjamin Allen; Katharine E. Jensen; Henry P. Foote; John S. Wettlaufer; Eric R. Dufresne

    2014-07-24T23:59:59.000Z

    From bone and wood to concrete and carbon fibre, composites are ubiquitous natural and engineering materials. Eshelby's inclusion theory describes how macroscopic stress fields couple to isolated microscopic inclusions, allowing prediction of a composite's bulk mechanical properties from a knowledge of its microstructure. It has been extended to describe a wide variety of phenomena from solid fracture to cell adhesion. Here, we show experimentally and theoretically that Eshelby's theory breaks down for small liquid inclusions in a soft solid. In this limit, an isolated droplet's deformation is strongly size-dependent with the smallest droplets mimicking the behaviour of solid inclusions. Furthermore, in opposition to the predictions of conventional composite theory, we find that finite concentrations of small liquid inclusions enhance the stiffness of soft solids. A straight-forward extension of Eshelby's theory, accounting for the surface tension of the solid-liquid interface, explains our experimental observations. The counterintuitive effect of liquid-stiffening of solids is expected whenever droplet radii are smaller than an elastocapillary length, given by the ratio of the surface tension to Young's modulus of the solid matrix.

  13. Liquid-film electron stripper

    DOE Patents [OSTI]

    Gavin, Basil F. (Albion, CA)

    1986-01-01T23:59:59.000Z

    An improved liquid-film electron stripper particularly for high intensity heavy ion beams which produces constant regenerated, stable, free-standing liquid films having an adjustable thickness between 0.3 to 0.05 microns. The improved electron stripper is basically composed of at least one high speed, rotating disc with a very sharp, precision-like, ground edge on one said of the disc's periphery and with a highly polished, flat, radial surface adjacent the sharp edge. A fine stream of liquid, such as oil, impinges at a 90.degree. angle adjacent the disc's sharp outer edge. Film terminators, located at a selected distance from the disc perimeter are positioned approximately perpendicular to the film. The terminators support, shape, and stretch the film and are arranged to assist in the prevention of liquid droplet formation by directing the collected film to a reservoir below without breaking or interfering with the film. One embodiment utilizes two rotating discs and associated terminators, with the discs rotating so as to form films in opposite directions, and with the second disc being located down beam-line relative to the first disc.

  14. Can hedge funds time market liquidity?

    E-Print Network [OSTI]

    Cao, Charles

    We explore a new dimension of fund managers' timing ability by examining whether they can time market liquidity through adjusting their portfolios' market exposure as aggregate liquidity conditions change. Using a large ...

  15. Mixing in a liquid metal electrode

    E-Print Network [OSTI]

    Kelley, Douglas H.

    Fluid mixing has first-order importance for many engineering problems in mass transport, including design and optimization of liquid-phase energy storage devices. Liquid metal batteries are currently being commercialized ...

  16. ELECTRONS ON THE SURFACE OF LIQUID HELIUM

    E-Print Network [OSTI]

    Lambert, David Kay

    2011-01-01T23:59:59.000Z

    ON THE SURFACE OF LIQUID HELIUM David Kay Lambert (Ph. D.ON THE SURFACE OF LIQUID HELIUM David Kay Lambert Materialsthe potential well near a helium surface, The charge density

  17. MUSHROOM WASTE MANAGEMENT PROJECT LIQUID WASTE MANAGEMENT

    E-Print Network [OSTI]

    of solid and liquid wastes generated at mushroom producing facilities. Environmental guidelines#12;MUSHROOM WASTE MANAGEMENT PROJECT LIQUID WASTE MANAGEMENT PHASE I: AUDIT OF CURRENT PRACTICE The Mushroom Waste Management Project (MWMP) was initiated by Environment Canada, the BC Ministry

  18. Method for enhanced atomization of liquids

    DOE Patents [OSTI]

    Thompson, Richard E. (27121 Puerta del Oro, Mission Viejo, CA 92691); White, Jerome R. (44755 Wyandotte, Hemet, CA 92544)

    1993-01-01T23:59:59.000Z

    In a process for atomizing a slurry or liquid process stream in which a slurry or liquid is passed through a nozzle to provide a primary atomized process stream, an improvement which comprises subjecting the liquid or slurry process stream to microwave energy as the liquid or slurry process stream exits the nozzle, wherein sufficient microwave heating is provided to flash vaporize the primary atomized process stream.

  19. Ionic liquids for rechargeable lithium batteries

    E-Print Network [OSTI]

    Salminen, Justin; Papaiconomou, Nicolas; Kerr, John; Prausnitz, John; Newman, John

    2008-01-01T23:59:59.000Z

    M. Armand, “Room temperature molten salts as lithium batteryZ. Suarez, “Ionic liquid (molten salt) phase organometallic

  20. Heterophase liquid states: Thermodynamics, structure, dynamics

    E-Print Network [OSTI]

    A. S. Bakai

    2015-01-12T23:59:59.000Z

    An overview of theoretical results and experimental data on the thermodynamics, structure and dynamics of the heterophase glass-forming liquids is presented. The theoretical approach is based on the mesoscopic heterophase fluctuations model (HPFM) developed within the framework of the bounded partition function approach. The Fischer cluster phenomenon, glass transition, liquid-liquid transformations, parametric phase diagram, cooperative dynamics and fragility of the glass-forming liquids is considered.

  1. Ionic Liquids for Utilization of Geothermal Energy

    Broader source: Energy.gov [DOE]

    DOE Geothermal Program Peer Review 2010 - Presentation. Project objective: to develop ionic liquids for two geothermal energy related applications.

  2. Cooperative motions in supercooled liquids and glasses

    E-Print Network [OSTI]

    Stevenson, Jacob D.

    2009-01-01T23:59:59.000Z

    P. Heat capacity and entropy of an equilibrium liquid fromliquids should correlate inversely with the con?gurational heat capacity,

  3. Nanoparticle enhanced ionic liquid heat transfer fluids

    DOE Patents [OSTI]

    Fox, Elise B.; Visser, Ann E.; Bridges, Nicholas J.; Gray, Joshua R.; Garcia-Diaz, Brenda L.

    2014-08-12T23:59:59.000Z

    A heat transfer fluid created from nanoparticles that are dispersed into an ionic liquid is provided. Small volumes of nanoparticles are created from e.g., metals or metal oxides and/or alloys of such materials are dispersed into ionic liquids to create a heat transfer fluid. The nanoparticles can be dispersed directly into the ionic liquid during nanoparticle formation or the nanoparticles can be formed and then, in a subsequent step, dispersed into the ionic liquid using e.g., agitation.

  4. Response functions near the liquid-liquid critical point of ST2 water

    E-Print Network [OSTI]

    Stanley, H. Eugene

    speci¿c heat capacity CP and the isothermal compressibility KT . We use two different methods: (i) fromResponse functions near the liquid-liquid critical point of ST2 water Erik Lascaris , T. A, and for four different system sizes, N = 63, 73, 83, and 93. We locate the liquid-liquid phase transition line

  5. Erasing no-man's land by thermodynamically stabilizing the liquid-liquid transition in tetrahedral particles

    E-Print Network [OSTI]

    Loss, Daniel

    compressibility KT and the isobaric heat capacity CP . In the LLCP hypothesis, the density anomalies of waterErasing no-man's land by thermodynamically stabilizing the liquid-liquid transition in tetrahedral, Sapienza, Universit´a di Roma, Piazzale Aldo Moro 2, I-00185, Roma, Italy. EFFECTS OF THE LIQUID-LIQUID

  6. Apparatus and method for spraying liquid materials

    DOE Patents [OSTI]

    Alvarez, J.L.; Watson, L.D.

    1988-01-21T23:59:59.000Z

    A method for spraying liquids involving a flow of gas which shears the liquid. A flow of gas is introduced in a converging-diverging nozzle where it meets and shears the liquid into small particles which are of a size and uniformity which can be controlled through adjustment of pressures and gas velocity. 5 figs.

  7. Liquid Transportation Fuels from Coal and Biomass

    E-Print Network [OSTI]

    Liquid Transportation Fuels from Coal and Biomass Technological Status, Costs, and Environmental for liquid fuels produced from coal or biomass. · Evaluate environmental, economic, policy, and social Impacts Panel on Alternative Liquid Transportation Fuels DOE LDV Workshop 7-26-10 Mike Ramage and Jim

  8. Computation of liquid-liquid equilibrium in multicomponent electrolyte systems

    SciTech Connect (OSTI)

    Vianna, R.F.; d`Avila, S.G. [Universidade Estadual de Campinas (Brazil)

    1996-12-31T23:59:59.000Z

    A computational algorithm for predicting liquid-liquid equilibrium (LLE) data, based on a generalization of the maximum likelihood method applied to implicit constraints, is presented. The algorithm accepts multicomponent data and binary interaction parameters. A comparative study of the models NRTL and electrolyte-NRTL, used for estimating activity coefficients in a quaternary electrolyte system, is presented and discussed. Results show that both models give accurate predictions and the algorithm presents a good performance without convergence or initialization problems. This suggests that the basic NRTL model can be used for describing phase behavior in weak electrolyte systems and the procedure can be of great use for design and optimization of processes involving multicomponent electrolyte systems. 9 refs., 1 fig., 1 tab.

  9. Liquid Propane Injection Technology Conductive to Today's North...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Technology Conductive to Today's North American Specification Liquid Propane Injection Technology Conductive to Today's North American Specification Liquid propane injection...

  10. Liquid Nitrogen Ice Cream (1st Grade) Lesson Plan

    E-Print Network [OSTI]

    . Introduce kids to liquid nitrogen. Explain that it is a liquid and is very cold (kids will be excited

  11. TETRAALKYLPHOSPHONIUM POLYOXOMETALATES AS NOVEL IONIC LIQUIDS.

    SciTech Connect (OSTI)

    DIETZ,M.L.; RICKERT, P.G.; ANTONIO, M.R.; FIRESTONE, M.A.; WISHART, J.F.; SZREDER, T.

    2007-11-30T23:59:59.000Z

    The pairing of a Lindqvist or Keggin polyoxometalate (POM) anion with an appropriate tetraalkylphosphonium cation, [R{sub 3}R{prime}P]{sup +}, has been shown to yield an original family of ionic liquids (POM-ILs), among them salts liquid at or near ambient temperature. The physicochemical properties of several such 'inorganic liquids', in particular their thermal properties, suggests the possible application of these compounds as robust, thermally-stable solvents for liquid-liquid extraction. A preliminary evaluation of the potential of POM-ILs in this application is presented.

  12. High pressure liquid level monitor

    DOE Patents [OSTI]

    Bean, Vern E. (Frederick, MD); Long, Frederick G. (Ijamsville, MD)

    1984-01-01T23:59:59.000Z

    A liquid level monitor for tracking the level of a coal slurry in a high-pressure vessel including a toroidal-shaped float with magnetically permeable bands thereon disposed within the vessel, two pairs of magnetic field generators and detectors disposed outside the vessel adjacent the top and bottom thereof and magnetically coupled to the magnetically permeable bands on the float, and signal processing circuitry for combining signals from the top and bottom detectors for generating a monotonically increasing analog control signal which is a function of liquid level. The control signal may be utilized to operate high-pressure control valves associated with processes in which the high-pressure vessel is used.

  13. Alien liquid detector and control

    SciTech Connect (OSTI)

    Potter, B.M.

    1980-09-02T23:59:59.000Z

    An alien liquid detector employs a monitoring element and an energizing circuit for maintaining the temperature of the monitoring element substantially above ambient temperature. For this purpose an electronic circit controls a flow of heating current to the monitoring element. The presence of an alien liquid is detected by sensing a predetermined change in heating current flow to the monitoring element, e.g., to distinguish between water and oil. In preferred embodiments the monitoring element is a thermistor whose resistance is compared with a reference resistance and heating current through the thermistor is controlled in accordance with the difference. In one embodiment a bridge circuit senses the resistance difference; the difference may be sensed by an operational amplifier arrangement. Features of the invention include positioning the monitoring element at the surface of water, slightly immersed, so that the power required to maintain the thermistor temperature substantially above ambient temperature serves to detect presence of oil pollution at the surface.

  14. Plasma-Surface Interactions on Liquids

    SciTech Connect (OSTI)

    R. Bastasz; W. Eckstein

    2000-05-01T23:59:59.000Z

    Liquid plasma-facing surfaces have been suggested as an option for advanced fusion devices, particularly in regions where solid materials may not survive over long operating periods. Because liquid surfaces can be replenished, they offer the possibility of tolerating intense particle bombardment and of recovering from off-normal events. As a preliminary step in understanding the nature of plasma-surface interactions on liquids, the authors consider some of the surface processes occurring in liquids undergoing irradiation by energetic particles. These include (1) sputtering, (2) segregation of liquid component species and impurities, (3) evaporation, and (4) trapping and release of incident particles. Aspects of these processes are examined for several candidate liquids, which represent three types of low-Z liquids: pure metals (Li), metallic alloys (Sn-Li), and compound insulators (Li{sub 2}BeF{sub 4}).

  15. Transient liquid phase ceramic bonding

    DOE Patents [OSTI]

    Glaeser, Andreas M. (Berkeley, CA)

    1994-01-01T23:59:59.000Z

    Ceramics are joined to themselves or to metals using a transient liquid phase method employing three layers, one of which is a refractory metal, ceramic or alloy. The refractory layer is placed between two metal layers, each of which has a lower melting point than the refractory layer. The three layers are pressed between the two articles to be bonded to form an assembly. The assembly is heated to a bonding temperature at which the refractory layer remains solid, but the two metal layers melt to form a liquid. The refractory layer reacts with the surrounding liquid and a single solid bonding layer is eventually formed. The layers may be designed to react completely with each other and form refractory intermetallic bonding layers. Impurities incorporated into the refractory metal may react with the metal layers to form refractory compounds. Another method for joining ceramic articles employs a ceramic interlayer sandwiched between two metal layers. In alternative embodiments, the metal layers may include sublayers. A method is also provided for joining two ceramic articles using a single interlayer. An alternate bonding method provides a refractory-metal oxide interlayer placed adjacent to a strong oxide former. Aluminum or aluminum alloys are joined together using metal interlayers.

  16. Bent core liquid crystal elastomers

    SciTech Connect (OSTI)

    Verduzco, R.; DiMasi, E.; Luchette, P.; Ho Hong, S.; Harden, J.; Palffy-Muhoray, P.; Kilbey II, S.M.; Sprunt, S.; Gleeson, G.T. Jakli, A.

    2010-07-28T23:59:59.000Z

    Liquid crystal (LC) elastomers with bent-core side-groups incorporate the properties of bent-core liquid crystals in a flexible and self-supporting polymer network. Bent-core liquid crystal elastomers (BCEs) with uniform alignment were prepared by attaching a reactive bent-core LC to poly(hydrogenmethylsiloxane) and crosslinking with a divinyl crosslinker. Phase behavior studies indicate a nematic phase over a wide temperature range that approaches room temperature, and thermoelastic measurements show that these BCEs can reversibly change their length by more than a factor of two upon heating and cooling. Small-angle X-ray scattering studies reveal multiple, broad low-angle peaks consistent with short-range smectic C order of the bent-core side groups. A comparison of these patterns with predictions of a Landau model for short-range smectic C order shows that the length scale for smectic ordering in BCEs is similar to that seen in pure bent-core LCs. The combination of rubber elasticity and smectic ordering of the bent-core side groups suggests that BCEs may be promising materials for sensing, actuating, and other advanced applications.

  17. Liquid Effluents Program mission analysis

    SciTech Connect (OSTI)

    Lowe, S.S.

    1994-09-27T23:59:59.000Z

    Systems engineering is being used to identify work to cleanup the Hanford Site. The systems engineering process transforms an identified mission need into a set of performance parameters and a preferred system configuration. Mission analysis is the first step in the process. Mission analysis supports early decision-making by clearly defining the program objectives, and evaluating the feasibility and risks associated with achieving those objectives. The results of the mission analysis provide a consistent basis for subsequent systems engineering work. A mission analysis was performed earlier for the overall Hanford Site. This work was continued by a ``capstone`` team which developed a top-level functional analysis. Continuing in a top-down manner, systems engineering is now being applied at the program and project levels. A mission analysis was conducted for the Liquid Effluents Program. The results are described herein. This report identifies the initial conditions and acceptable final conditions, defines the programmatic and physical interfaces and sources of constraints, estimates the resources to carry out the mission, and establishes measures of success. The mission analysis reflects current program planning for the Liquid Effluents Program as described in Liquid Effluents FY 1995 Multi-Year Program Plan.

  18. Hindered diffusion of coal liquids

    SciTech Connect (OSTI)

    Tsotsis, T.T.; Sahimi, M. (University of Southern California, Los Angeles, CA (United States). Dept. of Chemical Engineering); Webster, I.A. (Unocal Corp., Los Angeles, CA (United States))

    1992-01-01T23:59:59.000Z

    The molecules comprising coal liquids can range from less than 10 to several hundred [angstrom] in diameter. Their size is, therefore, comparable to the average pore size of most hydroprocessing catalysts. Thus, during processing, transport of these molecules into the catalyst occurs mainly by configurational'' or hindered diffusion,'' which is the result of two phenomena occurring in the pores; the distribution of solute molecules in the pores is affected by the pores and the solute molecules experience an increased hydrodynamic drag. The field of hindered diffusion has been reviewed by Deen [16]. The earliest studies in the filed were by Renkin et al. [17].

  19. Orifice mixing of immiscible liquids

    E-Print Network [OSTI]

    McDonough, Joseph Aloysius

    1960-01-01T23:59:59.000Z

    solution (7). The present study of orif1ce mixing is a continuation of previous research on this project which yielded a relationship explaining the effect of operating conditions upon the format1on of 1nterfacial area for the system water-kerosene.... The experimental technique evolved by Helch (18), Vesselhoff (19), McNair (8), and Scott (IA) was changed only slightly. Their work on water-kerosene was repeated for the liquid pairs trichloroethylene-water, heptanol-water, 20 per oent aqueous sucrose-kerosene...

  20. Natural Gas Plant Liquids Production

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 111 1,613 122 40 Buildingto17 3400,Information Administration22)May£661.DataNov-14Liquids

  1. Tokamak with liquid metal toroidal field coil

    DOE Patents [OSTI]

    Ohkawa, Tihiro (La Jolla, CA); Schaffer, Michael J. (San Diego, CA)

    1981-01-01T23:59:59.000Z

    Tokamak apparatus includes a pressure vessel for defining a reservoir and confining liquid therein. A toroidal liner disposed within the pressure vessel defines a toroidal space within the liner. Liquid metal fills the reservoir outside said liner. Electric current is passed through the liquid metal over a conductive path linking the toroidal space to produce a toroidal magnetic field within the toroidal space about the major axis thereof. Toroidal plasma is developed within the toroidal space about the major axis thereof.

  2. Liquid metal cooled nuclear reactor plant system

    DOE Patents [OSTI]

    Hunsbedt, Anstein (Los Gatos, CA); Boardman, Charles E. (Saratoga, CA)

    1993-01-01T23:59:59.000Z

    A liquid metal cooled nuclear reactor having a passive cooling system for removing residual heat resulting for fuel decay during reactor shutdown, or heat produced during a mishap. The reactor system is enhanced with sealing means for excluding external air from contact with the liquid metal coolant leaking from the reactor vessel during an accident. The invention also includes a silo structure which resists attack by leaking liquid metal coolant, and an added unique cooling means.

  3. Early Events in Ionic Liquid Radiation Chemistry

    SciTech Connect (OSTI)

    Wishart, J.F.; Cook, A.; Rimmer, R.D.; Gohdo, M.

    2010-09-14T23:59:59.000Z

    Ionic liquids are interesting and useful materials whose solvation time scales are up to thousands of times longer than in conventional solvents. The extended lifetimes of pre-solvated electrons and other energetic species in ionic liquids has profound consequences for the radiolytic product distributions and reactivity patterns. We use a newly developed, multiplexed variation of pulse-probe spectroscopy to measure the kinetics of the early dynamical and reactive events in ionic liquids.

  4. Liquid composition having ammonia borane and decomposing to form hydrogen and liquid reaction product

    DOE Patents [OSTI]

    Davis, Benjamin L; Rekken, Brian D

    2014-04-01T23:59:59.000Z

    Liquid compositions of ammonia borane and a suitably chosen amine borane material were prepared and subjected to conditions suitable for their thermal decomposition in a closed system that resulted in hydrogen and a liquid reaction product.

  5. Electrokinetic Power Generation from Liquid Water Microjets

    SciTech Connect (OSTI)

    Duffin, Andrew M.; Saykally, Richard J.

    2008-02-15T23:59:59.000Z

    Although electrokinetic effects are not new, only recently have they been investigated for possible use in energy conversion devices. We have recently reported the electrokinetic generation of molecular hydrogen from rapidly flowing liquid water microjets [Duffin et al. JPCC 2007, 111, 12031]. Here, we describe the use of liquid water microjets for direct conversion of electrokinetic energy to electrical power. Previous studies of electrokinetic power production have reported low efficiencies ({approx}3%), limited by back conduction of ions at the surface and in the bulk liquid. Liquid microjets eliminate energy dissipation due to back conduction and, measuring only at the jet target, yield conversion efficiencies exceeding 10%.

  6. Liquid metal Flow Meter - Final Report

    SciTech Connect (OSTI)

    Andersen, C.; Hoogendoom, S.; Hudson, B.; Prince, J.; Teichert, K.; Wood, J.; Chase, K.

    2007-01-30T23:59:59.000Z

    Measuring the flow of liquid metal presents serious challenges. Current commercially-available flow meters use ultrasonic, electromagnetic, and other technologies to measure flow, but are inadequate for liquid metal flow measurement because of the high temperatures required by most liquid metals. As a result of the reactivity and high temperatures of most liquid metals, corrosion and leakage become very serious safety concerns. The purpose of this project is to develop a flow meter for Lockheed Martin that measures the flow rate of molten metal in a conduit.

  7. Ionic liquids for rechargeable lithium batteries

    E-Print Network [OSTI]

    Salminen, Justin; Papaiconomou, Nicolas; Kerr, John; Prausnitz, John; Newman, John

    2008-01-01T23:59:59.000Z

    molten salts as lithium battery electrolyte,” ElectrochimicaFigure 15. Rechargeable lithium-ion battery. Figure 16 showsbattery. It is essential that an ionic liquid – lithium salt

  8. Hazardous Liquid Pipelines and Storage Facilities (Iowa)

    Broader source: Energy.gov [DOE]

    This statute regulates the permitting, construction, monitoring, and operation of pipelines transporting hazardous liquids, including petroleum products and coal slurries. The definition used in...

  9. Closed-field capacitive liquid level sensor

    DOE Patents [OSTI]

    Kronberg, J.W.

    1995-01-01T23:59:59.000Z

    A liquid level sensor based on a closed field circuit comprises a ring oscillator using a symmetrical array of plate units that creates a displacement current. The displacement current varies as a function of the proximity of a liquid to the plate units. The ring oscillator circuit produces an output signal with a frequency inversely proportional to the presence of a liquid. A continuous liquid level sensing device and a two point sensing device are both proposed sensing arrangements. A second set of plates may be located inside of the probe housing relative to the sensing plate units. The second set of plates prevent any interference between the sensing plate units.

  10. Interfacial ionic liquids: connecting static and dynamic...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    structures separated by an energy barrier (0.15 eV). Keywords: ionic liquid, supercapacitor, electric double layer, epitaxial graphene, x-ray reflectivity, RTIL, interfacial...

  11. Onsite Wastewater Treatment Systems: Liquid Chlorination

    E-Print Network [OSTI]

    Weaver, Richard; Lesikar, Bruce J.; Richter, Amanda; O'Neill, Courtney

    2008-10-23T23:59:59.000Z

    This publication explains the process, components, legal requirements, factors affecting performance, and maintenance needs of liquid chlorination systems for onsite wastewater treatment....

  12. Fully automated multifunctional ultrahigh pressure liquid chromatograp...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    phase liquid chromatography, or SCXRPLC) separations, and online phosphopeptides enrichment using a single binary nano-flow pump has been developed. With a simple operation of...

  13. Assessment of coal liquids as refinery feedstocks

    SciTech Connect (OSTI)

    Zhou, P.

    1992-02-01T23:59:59.000Z

    The R D of direct coal liquefaction has reached such a stage that current two-stage processes can produce coal liquids with high yields and improved quality at a reasonable cost. To fully realize the potential value, these coal liquids should be refined into high-value liquid transportation fuels. The purpose of this study is to assess coal liquids as feedstocks to be processed by modern petroleum refining technologies. After the introduction, Section 2.0 summarizes ASTM specifications for major transportation fuels: gasoline, jet fuel, and diesel fuel, which serve as a target for coal-liquid refining. A concise description of modern refining processes follows with an emphasis on the requirements for the raw materials. These provide criteria to judge the quality of coal liquids as a refinery feedstock for the production of marketable liquid fuels. Section 3.0 surveys the properties of coal liquids produced by various liquefaction processes. Compared with typical petroleum oils, the current two-stage coal liquids are: Light in boiling range and free of resids and metals; very low in sulfur but relatively high in oxygen; relatively low in hydrogen and high in cyclics content; and essentially toxicologically inactive when end point is lower than 650[degrees]F, particularly after hydroprocessing. Despite these characteristics, the coal liquids are basically similar to petroleum. The modern refining technology is capable of processing coal liquids into transportation fuels meeting all specifications, and hydroprocessinq is obviously the major tool. The important point is the determination of a reasonable product slate and an appropriate refining scheme.

  14. Assessment of coal liquids as refinery feedstocks

    SciTech Connect (OSTI)

    Zhou, P.

    1992-02-01T23:59:59.000Z

    The R&D of direct coal liquefaction has reached such a stage that current two-stage processes can produce coal liquids with high yields and improved quality at a reasonable cost. To fully realize the potential value, these coal liquids should be refined into high-value liquid transportation fuels. The purpose of this study is to assess coal liquids as feedstocks to be processed by modern petroleum refining technologies. After the introduction, Section 2.0 summarizes ASTM specifications for major transportation fuels: gasoline, jet fuel, and diesel fuel, which serve as a target for coal-liquid refining. A concise description of modern refining processes follows with an emphasis on the requirements for the raw materials. These provide criteria to judge the quality of coal liquids as a refinery feedstock for the production of marketable liquid fuels. Section 3.0 surveys the properties of coal liquids produced by various liquefaction processes. Compared with typical petroleum oils, the current two-stage coal liquids are: Light in boiling range and free of resids and metals; very low in sulfur but relatively high in oxygen; relatively low in hydrogen and high in cyclics content; and essentially toxicologically inactive when end point is lower than 650{degrees}F, particularly after hydroprocessing. Despite these characteristics, the coal liquids are basically similar to petroleum. The modern refining technology is capable of processing coal liquids into transportation fuels meeting all specifications, and hydroprocessinq is obviously the major tool. The important point is the determination of a reasonable product slate and an appropriate refining scheme.

  15. CMD-3 Liquid Xenon Calorimeter's signals processing

    E-Print Network [OSTI]

    CMD-3 Liquid Xenon Calorimeter's signals processing for timing measurements. Leonid Epshtein Budker connected to constitute 264 «towers»; signal of each tower is processed by electronic channel. Liquid Xenon functional channel scheme and signal's shapes in the typical point. Digital Signal Processing ADCCSALXe

  16. QUANTUM STATISTICS OF METASTABLE LIQUID HELIUM

    E-Print Network [OSTI]

    Caupin, Frédéric

    QUANTUM STATISTICS OF METASTABLE LIQUID HELIUM FR´ED´ERIC CAUPIN AND S´EBASTIEN BALIBAR Laboratoire in the spinodal line of liquid helium 3, for which experimental evidence has been reported. The calculations in the case of superfluid helium 4; we also consider the overpressurized region, and the location

  17. Remarks on Liquid Wall Research Mohamed Abdou

    E-Print Network [OSTI]

    Abdou, Mohamed

    rrr ×= BJF rrr ×= BJF rrr ×= BJF rrr ×= J r V r+- g r B r J r #12;· Magnetic Propulsion Liquid Metal Forces" · Gravity-Momentum Drive (GMD) · GMD with Swirl Flow · Electromagnetically Restrained · Magnetic Propulsion Plasma-Liquid Interface · Fluids with low vapor pressure at high temperature (e.g. Sn

  18. Liquid Biofuels Strategies and Policies in selected

    E-Print Network [OSTI]

    June 2011 Liquid Biofuels Strategies and Policies in selected African Countries A review of some of the challenges, activities and policy options for liquid biofuels Prepared for PISCES by Practical Action Biofuels Strategies and Policies in selected African Countries Although this research is funded by DFID

  19. Sewage sludge dewatering using flowing liquid metals

    DOE Patents [OSTI]

    Carlson, Larry W. (Oswego, IL)

    1986-01-01T23:59:59.000Z

    A method and apparatus for reducing the moisture content of a moist sewage sludge having a moisture content of about 50% to 80% and formed of small cellular micro-organism bodies having internally confined water is provided. A hot liquid metal is circulated in a circulation loop and the moist sewage sludge is injected in the circulation loop under conditions of temperature and pressure such that the confined water vaporizes and ruptures the cellular bodies. The vapor produced, the dried sludge, and the liquid metal are then separated. Preferably, the moist sewage sludge is injected into the hot liquid metal adjacent the upstream side of a venturi which serves to thoroughly mix the hot liquid metal and the moist sewage sludge. The venturi and the drying zone after the venturi are preferably vertically oriented. The dried sewage sludge recovered is available as a fuel and is preferably used for heating the hot liquid metal.

  20. Liquid crystal device and method thereof

    DOE Patents [OSTI]

    Shiyanovskii, Sergij V; Gu, Mingxia; Lavrentovich, Oleg D

    2012-10-23T23:59:59.000Z

    The invention provides a liquid crystal device and method thereof. Subsequent to applying a first electrical voltage on a liquid crystal to induce a reorientation of the liquid crystal, a second electrical voltage with proper polarity is applied on the liquid crystal to assist the relaxation of the reorientation that was induced by the first electrical voltage. The "switch-off" phase of the liquid crystal can therefore be accelerated or temporally shortened, and the device can exhibit better performance such as fast response to on/off signals. The invention can be widely used LCD, LC shutter, LC lens, spatial light modulator, telecommunication device, tunable filter, beam steering device, and electrically driven LC device, among others.

  1. Supported Ionic Liquid Membranes for Gas Separation

    SciTech Connect (OSTI)

    Myers, C.R.; Ilconich, J.B.; Pennline, H.W.; Luebke, D.R.

    2007-08-01T23:59:59.000Z

    Ionic liquids have been rapidly gaining attention for various applications including solvent separation and gas capture. These substances are noted for extremely low vapor pressure and high CO2 solubility making them ideal as transport or capture media for CO2 abatement in power generation applications. Ionic liquids, combined with various supports to form membranes, have been proven selective in CO2 separation. Several ionic liquids and a variety of polymer supports have been studied over a temperature range from 37°C to 300°C and have been optimized for stability. The membranes have demonstrated high permeability and high selectivity since the supported ionic liquid membranes incorporate functionality capable of chemically complexing CO2. A study aimed at improving supported ionic liquid membranes will examine their durability with greater transmembrane pressures and the effects on CO2 permeance, CO2/H2 selectivity and thermal stability.

  2. Dual liquid and gas chromatograph system

    DOE Patents [OSTI]

    Gay, Don D. (Aiken, SC)

    1985-01-01T23:59:59.000Z

    A chromatographic system that utilizes one detection system for gas chromatographic and micro-liquid chromatographic determinations. The detection system is a direct-current, atmospheric-pressure, helium plasma emission spectrometer. The detector utilizes a non-transparent plasma source unit which contains the plasma region and two side-arms which receive effluents from the micro-liquid chromatograph and the gas chromatograph. The dual nature of this chromatographic system offers: (1) extreme flexibility in the samples to be examined; (2) extremely low sensitivity; (3) element selectivity; (4) long-term stability; (5) direct correlation of data from the liquid and gas samples; (6) simpler operation than with individual liquid and gas chromatographs, each with different detection systems; and (7) cheaper than a commercial liquid chromatograph and a gas chromatograph.

  3. LECTRISATION ET CONDUCTION LECTRIQUE DES HYDROCARBURES LIQUIDES par L. BRUNINGHAUS.

    E-Print Network [OSTI]

    Boyer, Edmond

    ÉLECTRISATION ET CONDUCTION ÉLECTRIQUE DES HYDROCARBURES LIQUIDES par L. BRUNINGHAUS. Sommaire. - I. Electrisation des hydrocarbures. - Les hydrocarbures liquides s'électrisent (négativement) lorsqu'ils s hydrocarbures. - Les hydrocarbures liquides mani- festent trois régimes de conduction : 1° En couches épaisses

  4. Essays on Bank Optimal Portfolio Choice under Liquidity Constraint

    E-Print Network [OSTI]

    Kim, Eul Jin

    2012-10-19T23:59:59.000Z

    portfolio choices under liquidity constraints. Our theory predicts that liquidation plays an important role in a bank's portfolio model. Even though liquidation is an off-equilibrium phenomenon, banks can have rich loan portfolios due to the possibility...

  5. On the Fluctuations that Order and Frustrate Liquid Water

    E-Print Network [OSTI]

    Limmer, David

    2013-01-01T23:59:59.000Z

    Most nonpolar liquids have heat capacities that range from 8the maximum liquid state heat capacity[173]. ExperimentallyLIQUID AND SOLID WATER (a) Density (b) Compressibility (c) Heat Capacity

  6. Computer Simulations Indicate Calcium Carbonate Has a Dense Liquid...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Computer Simulations Indicate Calcium Carbonate Has a Dense Liquid Phase Computer Simulations Indicate Calcium Carbonate Has a Dense Liquid Phase Berkeley Lab research could help...

  7. Ventilation System to Improve Savannah River Site's Liquid Waste...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Ventilation System to Improve Savannah River Site's Liquid Waste Operations Ventilation System to Improve Savannah River Site's Liquid Waste Operations August 28, 2014 - 12:00pm...

  8. Energetics of Hydrogen Bond Network Rearrangements in Liquid...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Energetics of Hydrogen Bond Network Rearrangements in Liquid Water Print The unique chemical and physical properties of liquid water are thought to result from the highly...

  9. Dielectric liquid ionization chambers for detecting fast neutrons

    E-Print Network [OSTI]

    Boyd, Erin M

    2008-01-01T23:59:59.000Z

    Three ionization chambers with different geometries have been constructed and filled with dielectric liquids for detection of fast neutrons. The three dielectric liquids studied were Tetramethylsilane (TMS), Tetramethylpentane ...

  10. Formation of Supercooled Liquid Solutions from Nanoscale Amorphous...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Supercooled Liquid Solutions from Nanoscale Amorphous Solid Films of Methanol and Ethanol. Formation of Supercooled Liquid Solutions from Nanoscale Amorphous Solid Films of...

  11. Mixing it up - Measuring diffusion in supercooled liquid solutions...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Mixing it up - Measuring diffusion in supercooled liquid solutions of methanol and ethanol at temperatures near the glass Mixing it up - Measuring diffusion in supercooled liquid...

  12. Agenda for the Derived Liquids to Hydrogen Distributed Reforming...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Derived Liquids to Hydrogen Distributed Reforming Working Group (BILIWG) Hydrogen Production Technical Team Research Review Agenda for the Derived Liquids to Hydrogen Distributed...

  13. Energetic Materials for EGS Well Stimulation (solids, liquids...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energetic Materials for EGS Well Stimulation (solids, liquids, gases) Energetic Materials for EGS Well Stimulation (solids, liquids, gases) Energetic Materials for EGS Well...

  14. Elucidating graphene - Ionic Liquid interfacial region: a combined...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    graphene - Ionic Liquid interfacial region: a combined experimental and computational study. Elucidating graphene - Ionic Liquid interfacial region: a combined experimental and...

  15. New lithium-based ionic liquid electrolytes that resist salt...

    Energy Savers [EERE]

    lithium-based ionic liquid electrolytes that resist salt concentration polarization New lithium-based ionic liquid electrolytes that resist salt concentration polarization...

  16. Ionic Liquid-Enhanced Solid State Electrolyte Interface (SEI...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Liquid-Enhanced Solid State Electrolyte Interface (SEI) for Lithium Sulfur Batteries. Ionic Liquid-Enhanced Solid State Electrolyte Interface (SEI) for Lithium Sulfur Batteries....

  17. Ionic Liquids as Multifunctional Ashless Additives for Engine...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Multifunctional Ashless Additives for Engine Lubrication Ionic Liquids as Multifunctional Ashless Additives for Engine Lubrication A group of oil-miscible ionic liquids has been...

  18. Savannah River Site's Liquid Waste Operations Adds Multi-Functional...

    Office of Environmental Management (EM)

    Savannah River Site's Liquid Waste Operations Adds Multi-Functional Laboratory Savannah River Site's Liquid Waste Operations Adds Multi-Functional Laboratory January 28, 2015 -...

  19. Transfer Lines to Connect Liquid Waste Facilities and Salt Waste...

    Office of Environmental Management (EM)

    Transfer Lines to Connect Liquid Waste Facilities and Salt Waste Processing Facility Transfer Lines to Connect Liquid Waste Facilities and Salt Waste Processing Facility October...

  20. Distributed Reforming of Renewable Liquids via Water Splitting...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Renewable Liquids via Water Splitting using Oxygen Transport Membrane (OTM) (Presentation) Distributed Reforming of Renewable Liquids via Water Splitting using Oxygen Transport...

  1. antiferroelectric liquid crystals: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of phases in antiferroelectric liquid crystals Condensed Matter (arXiv) Summary: The free energy of antiferroelectric liquid crystal which takes into account polar order...

  2. antiferroelectric liquid crystal: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of phases in antiferroelectric liquid crystals Condensed Matter (arXiv) Summary: The free energy of antiferroelectric liquid crystal which takes into account polar order...

  3. Experimental and Modeling Studies of the Characteristics of Liquid...

    Energy Savers [EERE]

    Experimental and Modeling Studies of the Characteristics of Liquid Biofuels for Enhanced Combustion Experimental and Modeling Studies of the Characteristics of Liquid Biofuels for...

  4. alcohol liquid diet: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    biodiesel. Open Access Theses and Dissertations Summary: ??The most widely used process technology for biodiesel manufacture is the base-catalysed liquid-liquid...

  5. alkaline radioactive liquid: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    that is, their capital and the margins charged by their financiers. In times of crisis, reductions in market liquidity and funding liquidity are mutually reinforcing,...

  6. Improved peptide elution time prediction for reversed-phase liquid...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    peptide elution time prediction for reversed-phase liquid chromatography-MS by incorporating peptide sequence Improved peptide elution time prediction for reversed-phase liquid...

  7. Liquid-liquid equilibria of fuel oxygenate + water + hydrocarbon mixtures. 3: Effect of temperature

    SciTech Connect (OSTI)

    Wagner, G. [Universitaet Karlsruhe (Germany). Institut fuer Thermische Verfahrenstechnik; Sandler, S.I. [Univ. of Delaware, Newark, DE (United States). Center for Molecular and Engineering Thermodynamics

    1995-09-01T23:59:59.000Z

    The authors have measured the ternary liquid-liquid equilibria of water + ethanol mixtures with, separately, 2,2,4-trimethylpentane and toluene at 5 and 40 C, water + tert-amyl alcohol (TAOH) mixtures with, separately, toluene and hexane at 5 and 40 C, and of water + TAOH + pentane mixtures at 5 C. The ethanol-containing systems exhibit type 1 liquid-liquid phase behavior, and the TAOH-containing systems exhibit type 2 behavior. These data, together with the data they have previously reported at 25 C, provide information on how the liquid-liquid equilibria of these systems change as a function of temperature. While the addition of ethanol is found to increase the solubility of hydrocarbons in the aqueous phase, the concentration of the hydrocarbon in the water-rich phase decreases with increasing temperature. With the exception of hydrocarbon in the water-rich phase, the experimental data could be correlated quite well with either the UNIQUAC or NRTL models. For most of the systems considered here the predictions of the phase behavior with the liquid-liquid UNIFAC group-contribution model are only qualitatively correct. However, the liquid-liquid UNIFAC model erroneously predicts type 2 phase behavior to occur for water + ethanol + 2,2,4-trimethylpentane system at 5 C.

  8. Viscosity of a nanoconfined liquid during compression

    SciTech Connect (OSTI)

    Khan, Shah H. [Institute of Physics and Electronics, University of Peshawar, Peshawar 25120 (Pakistan); Kramkowski, Edward L.; Ochs, Peter J.; Wilson, David M.; Hoffmann, Peter M., E-mail: hoffmann@wayne.edu [Department of Physics and Astronomy, Wayne State University, Detroit, Michigan 48201 (United States)

    2014-01-13T23:59:59.000Z

    The viscous behavior of liquids under nanoconfinement is not well understood. Using a small-amplitude atomic force microscope, we found bulk-like viscosity in a nanoconfined, weakly interacting liquid. A further decrease in viscosity was observed at confinement sizes of a just few molecular layers. Overlaid over the continuum viscous behavior, we measured non-continuum stiffness and damping oscillations. The average stiffness of the confined liquid was found to scale linearly with the size of the confining tip, while the damping scales with the radius of curvature of the tip end.

  9. Light Collection in Liquid Noble Gases

    SciTech Connect (OSTI)

    McKinsey, Dan [Yale University

    2013-05-29T23:59:59.000Z

    Liquid noble gases are increasingly used as active detector materials in particle and nuclear physics. Applications include calorimeters and neutrino oscillation experiments as well as searches for neutrinoless double beta decay, direct dark matter, muon electron conversion, and the neutron electric dipole moment. One of the great advantages of liquid noble gases is their copious production of ultraviolet scintillation light, which contains information about event energy and particle type. I will review the scintillation properties of the various liquid noble gases and the means used to collect their scintillation light, including recent advances in photomultiplier technology and wavelength shifters.

  10. Shearing Flows in Liquid Crystal Models

    E-Print Network [OSTI]

    Dorn, Timothy

    2012-05-31T23:59:59.000Z

    . The director field is the realization of local averaging to de- scribe the natural state in a nematic liquid crystal, Figure 1.1. For any natural alignment of the liquid crystal, n?, one prescribes that W (n?,?n?) = 0. Since the director field is used... derivative of h by the formula D Dt h(t,x) = ?h? t +(u · ~?)h. The acceleration is of the liquid crystal material through the point x is given by a(t,x) = Du Dt . Following the classical approach one assumes that for every open subset Wt ??, trav- eling along...

  11. Proton Electrodynamics in Liquid Water

    E-Print Network [OSTI]

    A. A. Volkov; V. G. Artemov; A. V. Pronin

    2013-02-20T23:59:59.000Z

    The dielectric spectrum of liquid water, $10^{4} - 10^{11}$ Hz, is interpreted in terms of diffusion of charges, formed as a result of self-ionization of H$_{2}$O molecules. This approach explains the Debye relaxation and the dc conductivity as two manifestations of this diffusion. The Debye relaxation is due to the charge diffusion with a fast recombination rate, $1/\\tau_{2}$, while the dc conductivity is a manifestation of the diffusion with a much slower recombination rate, $1/\\tau_{1}$. Applying a simple model based on Brownian-like diffusion, we find $\\tau_{2} \\simeq 10^{-11}$ s and $\\tau_{1} \\simeq 10^{-6}$ s, and the concentrations of the charge carriers, involved in each of the two processes, $N_{2} \\simeq 5 \\times 10^{26}$ m$^{-3}$ and $N_{1} \\simeq 10^{14}$ m$^{-3}$. Further, we relate $N_{2}$ and $N_{1}$ to the total concentration of H$_{3}$O$^{+}$--OH$^{-}$ pairs and to the pH index, respectively, and find the lifetime of a single water molecule, $\\tau_{0} \\simeq 10^{-9}$ s. Finally, we show that the high permittivity of water results mostly from flickering of separated charges, rather than from reorientations of intact molecular dipoles.

  12. Electron localization in liquid acetonitrile.

    SciTech Connect (OSTI)

    Shkrob, I. A.; Sauer, M. C.; Chemistry

    2002-10-03T23:59:59.000Z

    Time-resolved one- and two-pulse laser dc photoconductivity has been used to observe two kinds of reducing species, anion-1 and anion-2, in liquid acetonitrile. At 25 C, the standard enthalpy of conversion from anion-1 to anion-2 is -44.3 {+-} 3.6 kJ/mol and the conversion time is 3 ns. The high-temperature form, anion-1, absorbs in the IR and migrates >3.3 times faster than any other ion in acetonitrile. This rapid migration has a low activation energy of 3.2 kJ/mol (vs 7.6 kJ/mol for other ions). Anion-1 rapidly transfers the electron to acceptors with high electron affinity, with rate constant up to 10{sup 11} M{sup -1} s{sup -1}. The low-temperature form, anion-2, absorbs in the visible and exhibits normal mobility and electron-transfer rates, ca. 1.5 x 10{sup 10} M{sup -1} s{sup -1}. It reacts, by proton transfer, with two hydrogen-bonded molecules of water and/or aliphatic alcohols. Laser photoexcitation of these two solvent anions in their respective absorption bands leads to the formation of CH{sub 3} and CN{sup -}. We present arguments indicating that anion-2 is a dimer radical anion of acetonitrile, whereas anion-1 is a multimer radical anion that may be regarded as a 'solvated electron'.

  13. Laser Micromachining: Advantages of Liquid Environments

    E-Print Network [OSTI]

    Petta, Jason

    Laser Micromachining: Advantages of Liquid Environments Marc J. Palmeri Princeton University Arnold Lab #12;Outline · Motivation ­ Applications of laser micromachining ­ Problems with laser micromachining · How do lasers work? · What is laser micromachining? · Micromachining assembly · Methods

  14. Liquid Lithium Experiments in CDX-U

    SciTech Connect (OSTI)

    R. Majeski; R. Doerner; R. Kaita; G. Antar; J. Timberlake; et al

    2000-11-15T23:59:59.000Z

    The initial results of experiments involving the use of liquid lithium as a plasma facing component in the Current Drive Experiment-Upgrade (CDX-U) are reported. Studies of the interaction of a steady-state plasma with liquid lithium in the Plasma Interaction with Surface and Components Experimental Simulator (PISCES-B) are also summarized. In CDX-U a solid or liquid lithium covered rail limiter was introduced as the primary limiting surface for spherical torus discharges. Deuterium recycling was observed to be reduced, but so far not eliminated, for glow discharge-cleaned lithium surfaces. Some lithium influx was observed during tokamak operation. The PISCES-B results indicate that the rates of plasma erosion of lithium can exceed predictions by an order of magnitude at elevated temperatures. Plans to extend the CDX-U experiments to large area liquid lithium toroidal belt limiters are also described.

  15. Future of Liquid Biofuels for APEC Economies

    SciTech Connect (OSTI)

    Milbrandt, A.; Overend, R. P.

    2008-05-01T23:59:59.000Z

    This project was initiated by APEC Energy Working Group (EWG) to maximize the energy sector's contribution to the region's economic and social well-being through activities in five areas of strategic importance including liquid biofuels production and development.

  16. Experimental investigation on liquid behaviors in nanopores

    E-Print Network [OSTI]

    Lu, Weiyi

    2011-01-01T23:59:59.000Z

    an nd as an ex xternal pressu ure is applie ed, the liquid d1–90 mm/min. Wh hen the pressu ure reached ab bout 50 MPa, ,

  17. Phosphonium-based ionic liquids and uses

    DOE Patents [OSTI]

    Del Sesto, Rico E; Koppisch, Andrew T; Lovejoy, Katherine S; Purdy, Geraldine M

    2014-12-30T23:59:59.000Z

    Phosphonium-based room temperature ionic liquids ("RTILs") were prepared. They were used as matrices for Matrix-Assisted Laser Desorption Ionization (MALDI) mass spectrometry and also for preparing samples of dyes for analysis.

  18. Liquid crystal variable retarders in atomic scattering

    SciTech Connect (OSTI)

    Furst, J.E.; Yu, D.H.; Hayes, P.A.; DSouza, C.M.; Williams, J.F. [Physics Department, Centre for Atomic, Molecular, and Surface Physics, The University of Western Australia, Nedlands. WA. 6907 (Australia)] [Physics Department, Centre for Atomic, Molecular, and Surface Physics, The University of Western Australia, Nedlands. WA. 6907 (Australia)

    1996-11-01T23:59:59.000Z

    The applications of liquid crystal variable retarders in the production of spin-polarized electrons and in the determination of the polarization of optical radiation from atoms excited by polarized electrons are discussed. The advantages of using liquid crystal variable retarders in the measurement of Stokes parameters are insensitivity to the incident photon direction, large transmission diameter, variable retardation over large wavelength range without mechanical movement, and {ital in} {ital situ} calibration. {copyright} {ital 1996 American Institute of Physics.}

  19. Superbase-derived protic ionic liquids

    DOE Patents [OSTI]

    Dai, Sheng; Luo, Huimin; Baker, Gary A.

    2013-09-03T23:59:59.000Z

    Protic ionic liquids having a composition of formula (A.sup.-)(BH.sup.+) wherein A.sup.- is a conjugate base of an acid HA, and BH.sup.+ is a conjugate acid of a superbase B. In particular embodiments, BH.sup.+ is selected from phosphazenium species and guanidinium species encompassed, respectively, by the general formulas: ##STR00001## The invention is also directed to films and membranes containing these protic ionic liquids, with particular application as proton exchange membranes for fuel cells.

  20. Photosensitive dopants for liquid noble gases

    DOE Patents [OSTI]

    Anderson, David F. (Wheaton, IL)

    1988-01-01T23:59:59.000Z

    In an ionization type detector for high energy radiation wherein the energy of incident radiation is absorbed through the ionization of a liquid noble gas and resulting free charge is collected to form a signal indicative of the energy of the incident radiation, an improvement comprising doping the liquid noble gas with photosensitive molecules to convert scintillation light due to recombination of ions, to additional free charge.

  1. Equilibration of a spinless Luttinger liquid.

    SciTech Connect (OSTI)

    Matveev, K. A.; Andreev, A. V. (Materials Science Division); (Univ. Washington)

    2012-01-01T23:59:59.000Z

    We study how a Luttinger liquid of spinless particles in one dimension approaches thermal equilibrium. Full equilibration requires processes of backscattering of excitations, which occur at energies of the order of the bandwidth. Such processes are not accounted for by the Luttinger-liquid theory. We treat the high-energy excitations as mobile impurities and derive an expression for the equilibration rate in terms of their spectrum. Our results apply at any interaction strength.

  2. Nonconventional Liquid Fuels (released in AEO2006)

    Reports and Publications (EIA)

    2006-01-01T23:59:59.000Z

    Higher prices for crude oil and refined petroleum products are opening the door for nonconventional liquids to displace petroleum in the traditional fuel supply mix. Growing world demand for diesel fuel is helping to jump-start the trend toward increasing production of nonconventional liquids, and technological advances are making the nonconventional alternatives more viable commercially. Those trends are reflected in the Annual Energy Outlook 2006 projections.

  3. Behavior of Supercooled Aqueous Solutions Stemming from Hidden Liquid-Liquid Transition in Water

    E-Print Network [OSTI]

    John W. Biddle; Vincent Holten; Mikhail A. Anisimov

    2014-08-21T23:59:59.000Z

    A popular hypothesis that explains the anomalies of supercooled water is the existence of a metastable liquid-liquid transition hidden below the line of homogeneous nucleation. If this transition exists and if it is terminated by a critical point, the addition of a solute should generate a line of liquid-liquid critical points emanating from the critical point of pure metastable water. We have analyzed thermodynamic consequences of this scenario. In particular, we consider the behavior of two systems, H2O-NaCl and H2O-glycerol. We find the behavior of the heat capacity in supercooled aqueous solutions of NaCl, as reported by Archer and Carter, to be consistent with the presence of the metastable liquid-liquid transition. We suggest an interpretation of the liquid-liquid transition in aqueous solutions of glycerol, recently observed by Murata and Tanaka, elucidating the non-conserved nature of the order parameter, its coupling with density and concentration, and the peculiarity of "spinodal decomposition without phase separation". We also show how the shape of the critical line in a solution controls the difference in concentration of the coexisting liquid phases.

  4. Boiling of nuclear liquid in the micro-canonical ensemble

    E-Print Network [OSTI]

    -dependence of the nuclear symmetry energy and the critical temperature of 1 #12;Boiling of nuclear liquid in the microBoiling of nuclear liquid in the micro-canonical ensemble K. Miyazaki E-mail: miyazakiro@rio.odn.ne.jp Abstract New calculus of the liquid-gas phase transition is developed for the boiling of nuclear liquid

  5. FULLY INTEGRATED ONE PHASE LIQUID COOLING SYSTEM FOR ORGANIC BOARDS

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    FULLY INTEGRATED ONE PHASE LIQUID COOLING SYSTEM FOR ORGANIC BOARDS D. May1 , B. Wunderle1 , F approach: A liquid cooling system has to be cus- tomised to its application. Further, it requires many dis in designing liquid cooling solu- tions are performance, reliability and price. To that end a one-phase liquid

  6. Semiconductor liquid crystal composition and methods for making the same

    DOE Patents [OSTI]

    Alivisatos, A. Paul; Li, Liang-shi

    2005-04-26T23:59:59.000Z

    Semiconductor liquid crystal compositions and methods for making such compositions are disclosed. One embodiment of the invention is directed to a liquid crystal composition including a solvent and semiconductor particles in the solvent. The solvent and the semiconductor particles are in an effective amount in the liquid crystal composition to form a liquid crystal phase.

  7. Liquid fuels production from biomass. Final report

    SciTech Connect (OSTI)

    Levy, P. F.; Sanderson, J. E.; Ashare, E.; Wise, D. L.; Molyneaux, M. S.

    1980-06-30T23:59:59.000Z

    The current program to convert biomass into liquid hydrocarbon fuels is an extension of a previous program to ferment marine algae to acetic acid. In that study it was found that marine algae could be converted to higher aliphatic organic acids and that these acids could be readily removed from the fermentation broth by membrane or liquid-liquid extraction. It was then proposed to convert these higher organic acids via Kolbe electrolysis to aliphatic hydrocarbons, which may be used as a diesel fuel. The specific goals for the current porgram are: (1) establish conditions under which substrates other than marine algae may be converted in good yield to organic acids, here the primary task is methane suppression; (2) modify the current 300-liter fixed packed bed batch fermenter to operate in a continuous mode; (3) change from membrane extraction of organic acids to liquid-liquid extraction; (4) optimize the energy balance of the electrolytic oxidation process, the primary task is to reduce the working potential required for the electrolysis while maintaining an adequate current density; (5) scale the entire process up to match the output of the 300 liter fermenter; and (6) design pilot plant and commercial size plant (1000 tons/day) processes for converting biomass to liquid hydrocarbon fuels and perform an economic analysis for the 1000 ton/day design.

  8. Process for stabilization of coal liquid fractions

    DOE Patents [OSTI]

    Davies, Geoffrey (Boston, MA); El-Toukhy, Ahmed (Alexandria, EG)

    1987-01-01T23:59:59.000Z

    Coal liquid fractions to be used as fuels are stabilized against gum formation and viscosity increases during storage, permitting the fuel to be burned as is, without further expensive treatments to remove gums or gum-forming materials. Stabilization is accomplished by addition of cyclohexanol or other simple inexpensive secondary and tertiary alcohols, secondary and tertiary amines, and ketones to such coal liquids at levels of 5-25% by weight with respect to the coal liquid being treated. Cyclohexanol is a particularly effective and cost-efficient stabilizer. Other stabilizers are isopropanol, diphenylmethanol, tertiary butanol, dipropylamine, triethylamine, diphenylamine, ethylmethylketone, cyclohexanone, methylphenylketone, and benzophenone. Experimental data indicate that stabilization is achieved by breaking hydrogen bonds between phenols in the coal liquid, thereby preventing or retarding oxidative coupling. In addition, it has been found that coal liquid fractions stabilized according to the invention can be mixed with petroleum-derived liquid fuels to produce mixtures in which gum deposition is prevented or reduced relative to similar mixtures not containing stabilizer.

  9. Damping of liquid sloshing by foams

    E-Print Network [OSTI]

    Alban Sauret; François Boulogne; Jean Cappello; Emilie Dressaire; Howard A. Stone

    2015-02-01T23:59:59.000Z

    When a container is set in motion, the free surface of the liquid starts to oscillate or slosh. Such effects can be observed when a glass of water is handled carelessly and the fluid sloshes or even spills over the rims of the container. However, beer does not slosh as readily as water, which suggests that foam could be used to damp sloshing. In this work, we study experimentally the effect on sloshing of a liquid foam placed on top of a liquid bath. We generate a monodisperse two-dimensional liquid foam in a rectangular container and track the motion of the foam. The influence of the foam on the sloshing dynamics is experimentally characterized: only a few layers of bubbles are sufficient to significantly damp the oscillations. We rationalize our experimental findings with a model that describes the foam contribution to the damping coefficient through viscous dissipation on the walls of the container. Then we extend our study to confined three-dimensional liquid foam and observe that the behavior of 2D and confined 3D systems are very similar. Thus we conclude that only the bubbles close to the walls have a significant impact on the dissipation of energy. The possibility to damp liquid sloshing using foam is promising in numerous industrial applications such as the transport of liquefied gas in tankers or for propellants in rocket engines.

  10. SEAPORT LIQUID NATURAL GAS STUDY

    SciTech Connect (OSTI)

    COOK,Z.

    1999-02-01T23:59:59.000Z

    The Seaport Liquid Natural Gas Study has attempted to evaluate the potential for using LNG in a variety of heavy-duty vehicle and equipment applications at the Ports of Los Angeles and Oakland. Specifically, this analysis has focused on the handling and transport of containerized cargo to, from and within these two facilities. In terms of containerized cargo throughput, Los Angeles and Oakland are the second and sixth busiest ports in the US, respectively, and together handle nearly 4.5 million TEUs per year. At present, the landside handling and transportation of containerized cargo is heavily dependent on diesel-powered, heavy-duty vehicles and equipment, the utilization of which contributes significantly to the overall emissions impact of port-related activities. Emissions from diesel units have been the subject of increasing scrutiny and regulatory action, particularly in California. In the past two years alone, particulate matter from diesel exhaust has been listed as a toxic air contaminant by CAM, and major lawsuits have been filed against several of California's largest supermarket chains, alleging violation of Proposition 65 statutes in connection with diesel emissions from their distribution facilities. CARE3 has also indicated that it may take further regulatory action relating to the TAC listing. In spite of these developments and the very large diesel emissions associated with port operations, there has been little AFV penetration in these applications. Nearly all port operators interviewed by CALSTART expressed an awareness of the issues surrounding diesel use; however, none appeared to be taking proactive steps to address them. Furthermore, while a less controversial issue than emissions, the dominance of diesel fuel use in heavy-duty vehicles contributes to a continued reliance on imported fuels. The increasing concern regarding diesel use, and the concurrent lack of alternative fuel use and vigorous emissions reduction activity at the Ports provide both the backdrop and the impetus for this study.

  11. Liquid over-feeding air conditioning system and method

    DOE Patents [OSTI]

    Mei, Viung C. (Oak Ridge, TN); Chen, Fang C. (Knoxville, TN)

    1993-01-01T23:59:59.000Z

    A refrigeration air conditioning system utilizing a liquid over-feeding operation is described. A liquid refrigerant accumulator-heat exchanger is placed in the system to provide a heat exchange relationship between hot liquid refrigerant discharged from condenser and a relatively cool mixture of liquid and vaporous refrigerant discharged from the evaporator. This heat exchange relationship substantially sub-cools the hot liquid refrigerant which undergoes little or no evaporation across the expansion device and provides a liquid over-feeding operation through the evaporator for effectively using 100 percent of evaporator for cooling purposes and for providing the aforementioned mixture of liquid and vaporous refrigerant.

  12. Liquid over-feeding air conditioning system and method

    DOE Patents [OSTI]

    Mei, V.C.; Chen, F.C.

    1993-09-21T23:59:59.000Z

    A refrigeration air conditioning system utilizing a liquid over-feeding operation is described. A liquid refrigerant accumulator-heat exchanger is placed in the system to provide a heat exchange relationship between hot liquid refrigerant discharged from condenser and a relatively cool mixture of liquid and vaporous refrigerant discharged from the evaporator. This heat exchange relationship substantially sub-cools the hot liquid refrigerant which undergoes little or no evaporation across the expansion device and provides a liquid over-feeding operation through the evaporator for effectively using 100 percent of evaporator for cooling purposes and for providing the aforementioned mixture of liquid and vaporous refrigerant. 1 figure.

  13. Fuel gas production by microwave plasma in liquid

    SciTech Connect (OSTI)

    Nomura, Shinfuku; Toyota, Hiromichi; Tawara, Michinaga; Yamashita, Hiroshi; Matsumoto, Kenya [Graduate School of Science and Engineering, Ehime University, 3 Bunkyo-cho, Matsuyama, Ehime 790-8577 (Japan); Shikoku Industry and Technology Promotion Center, 2-5 Marunouchi, Takamatsu, Kagawa 760-0033 (Japan)

    2006-06-05T23:59:59.000Z

    We propose to apply plasma in liquid to replace gas-phase plasma because we expect much higher reaction rates for the chemical deposition of plasma in liquid than for chemical vapor deposition. A reactor for producing microwave plasma in a liquid could produce plasma in hydrocarbon liquids and waste oils. Generated gases consist of up to 81% hydrogen by volume. We confirmed that fuel gases such as methane and ethylene can be produced by microwave plasma in liquid.

  14. Rotor for processing liquids using movable capillary tubes

    DOE Patents [OSTI]

    Johnson, W.F.; Burtis, C.A.; Walker, W.A.

    1987-07-17T23:59:59.000Z

    A rotor assembly for processing liquids, especially whole blood samples, is disclosed. The assembly includes apparatus for separating non-liquid components of whole blood samples from liquid components, apparatus for diluting the separated liquid component with a diluent and apparatus for transferring the diluted sample to an external apparatus for analysis. The rotor assembly employs several movable capillary tubes to handle the sample and diluents. A method for using the rotor assembly to process liquids is also described. 5 figs.

  15. Rotor for processing liquids using movable capillary tubes

    DOE Patents [OSTI]

    Johnson, Wayne F. (Loudon, TN); Burtis, Carl A. (Oak Ridge, TN); Walker, William A. (Knoxville, TN)

    1989-05-30T23:59:59.000Z

    A rotor assembly for processing liquids, especially whole blood samples, is disclosed. The assembly includes apparatus for separating non-liquid components of whole blood samples from liquid components, apparatus for diluting the separated liquid component with a diluent and apparatus for transferring the diluted sample to an external apparatus for analysis. The rotor assembly employs several movable capillary tubes to handle the sample and diluents. A method for using the rotor assembly to process liquids is also described.

  16. Rotor for processing liquids using movable capillary tubes

    DOE Patents [OSTI]

    Johnson, Wayne F. (Loudon, TN); Burtis, Carl A. (Oak Ridge, TN); Walker, William A. (Knoxville, TN)

    1989-01-01T23:59:59.000Z

    A rotor assembly for processing liquids, especially whole blood samples, is disclosed. The assembly includes apparatus for separating non-liquid components of whole blood samples from liquid components, apparatus for diluting the separated liquid component with a diluent and apparatus for transferring the diluted sample to an external apparatus for analysis. The rotor assembly employs several movable capillary tubes to handle the sample and diluents. A method for using the rotor assembly to process liquids is also described.

  17. SEPARATION OF COPPER FROM METALS IN AN ALLOY BY LIQUID-LIQUID EXTRACTION

    E-Print Network [OSTI]

    Weston, Ken

    /L. Extraction. The extraction procedure is the same for the sample, standards and blank (water between sample extractions with water. The chloroform extracts at this point will normally be cloudySEPARATION OF COPPER FROM METALS IN AN ALLOY BY LIQUID-LIQUID EXTRACTION Background Reading: Harris

  18. Quaternary liquid-liquid equilibrium of n-heptane-toluene-o-xylene-propylene carbonate

    SciTech Connect (OSTI)

    Salem, A.B.S.H.; Hamad, E.Z.; Al-Naafa, M.A. (King Fahd Univ. of Petroleum and Minerals, Dhahran (Saudi Arabia). Chemical Engineering Dept.)

    1994-03-01T23:59:59.000Z

    Liquid-liquid equilibrium data for the system n-heptane/toluene/o-xylene/propylene carbonate were obtained at 25 OC. Experimental tie line data were measured by gas chromatographic analysis. The UNIQUAC and NRTL models were used to predict the quaternary data from the corresponding ternary data. Agreement between the predictions and the experimental data was satisfactory.

  19. Liquid-liquid equilibria for ternary systems containing hydrocarbons and propylene carbonate

    SciTech Connect (OSTI)

    Annesini, M.C.; Gironi, F.; Marrelli, L.

    1985-04-01T23:59:59.000Z

    Experimental data of liquid-liquid equillibrium at 20/sup 0/C are reported for six ternary systems containing propylene carbonate with n-hexane-benzene, n-hexane-ethylbenzene, n-heptane-toluene, n-heptane-ethylbenzene, n-octane-o-xylene, and n-octane-ethylbenzene. The data are correlated by means of NRTL and UNIQUAC models and relative parameters are given.

  20. Images reveal that atmospheric particles can undergo liquid-liquid phase separations

    SciTech Connect (OSTI)

    You, Yuan; Renbaum-Wolff, Lindsay; Carreras-Sospedra, Marc; Hanna, Sarah; Hiranuma, Naruki; Kamal, Saeid; Smith, Mackenzie L.; Zhang, Xiaolu; Weber, Rodney; Shilling, John E.; Dabdub, Donald; Martin, Scot T.; Bertram, Allan K.

    2012-07-30T23:59:59.000Z

    A large fraction of submicron atmospheric particles contains both organic material and inorganic salts. As the relative humidity cycles in the atmosphere, these mixed particles can undergo a range of phase transitions, possibly including liquid-liquid phase separation. If liquid-liquid phase separation occurs, the gas-particle partitioning of atmospheric semi-volatile organic compounds, the scattering and absorption of solar radiation, and the uptake of reactive gas species on atmospheric particles will be affected, with important implications for climate predictions. The actual occurrence of these types of phase transitions within individual atmospheric particles has been considered uncertain, in large part because of the absence of observations for real-world samples. Here, using optical and fluorescence microscopy, we observe the coexistence of two non-crystalline phases in particles generated from real-world samples collected on multiple days in Atlanta, Georgia, and in particles generated in the laboratory using atmospheric conditions. These results reveal that atmospheric particles can undergo liquid-liquid phase separations. Using a box model, we show that liquid-liquid phase separation can result in increased concentrations of gas-phase NO3 and N2O5 in the Atlanta region, due to decreased particle uptake of N2O5.

  1. Process for the production of liquid hydrocarbons

    DOE Patents [OSTI]

    Bhatt, Bharat Lajjaram; Engel, Dirk Coenraad; Heydorn, Edward Clyde; Senden, Matthijis Maria Gerardus

    2006-06-27T23:59:59.000Z

    The present invention concerns a process for the preparation of liquid hydrocarbons which process comprises contacting synthesis gas with a slurry of solid catalyst particles and a liquid in a reactor vessel by introducing the synthesis gas at a low level into the slurry at conditions suitable for conversion of the synthesis gas into liquid hydrocarbons, the solid catalyst particles comprising a catalytic active metal selected from cobalt or iron on a porous refractory oxide carrier, preferably selected from silica, alumina, titania, zirconia or mixtures thereof, the catalyst being present in an amount between 10 and 40 vol. percent based on total slurry volume liquids and solids, and separating liquid material from the solid catalyst particles by using a filtration system comprising an asymmetric filtration medium (the selective side at the slurry side), in which filtration system the average pressure differential over the filtration medium is at least 0.1 bar, in which process the particle size distribution is such that at least a certain amount of the catalyst particles is smaller than the average pore size of the selective layer of the filtration medium. The invention also comprises an apparatus to carry out the process described above.

  2. Global cloud liquid water path simulations

    SciTech Connect (OSTI)

    Lemus, L. [Southern Hemisphere Meteorology, Clayton, Victoria (Australia)] [Southern Hemisphere Meteorology, Clayton, Victoria (Australia); Rikus, L. [Bureau of Meteorology Research Centre, Melbourne, Victoria (Australia)] [Bureau of Meteorology Research Centre, Melbourne, Victoria (Australia); Martin, C.; Platt, R. [CSIRO, Aspendale, Victoria (Australia)] [CSIRO, Aspendale, Victoria (Australia)

    1997-01-01T23:59:59.000Z

    A new parameterization of cloud liquid water and ice content has been included in the Bureau of Meteorology Global Assimilation and Prediction System. The cloud liquid water content is derived from the mean cloud temperatures in the model using an empirical relationship based on observations. The results from perpetual January and July simulations are presented and show that the total cloud water path steadily decreases toward high latitudes, with two relative maxima at midlatitudes and a peak at low latitudes. To validate the scheme, the simulated fields need to be processed to produce liquid water paths that can be directly compared with the corresponding field derived from Special Sensor Microwave/Imager (SSM/I) data. This requires the identification of cloud ice water content within the parameterization and a prescription to account for the treatment of strongly precipitating subgrid-scale cloud. The resultant cloud liquid water paths agree qualitatively with the SSM/I data but show some systematic errors that are attributed to corresponding errors in the model`s simulation of cloud amounts. Given that a more quantitative validation requires substantial improvement in the model`s diagnostic cloud scheme, the comparison with the SSM/I data indicates that the cloud water path, derived from the cloud liquid water content parameterization introduced in this paper, is consistent with the observations and can be usefully incorporated in the prediction system. 40 refs., 11 figs., 1 tab.

  3. Double-duct liquid metal magnetohydrodynamic engine

    DOE Patents [OSTI]

    Haaland, Carsten M. (Oak Ridge, TN)

    1995-01-01T23:59:59.000Z

    An internal combustion, liquid metal (LM) magnetohydrodynamic (MHD) engine and an alternating current (AC) magnetohydrodynamic generator, are used in combination to provide useful AC electric energy output. The engine design has-four pistons and a double duct configuration, with each duct containing sodium potassium liquid metal confined between free pistons located at either end of the duct. The liquid metal is forced to flow back and forth in the duct by the movement of the pistons, which are alternatively driven by an internal combustion process. In the MHD generator, the two LM-MHD ducts pass in close proximity through a Hartmann duct with output transformer. AC power is produced by operating the engine with the liquid metal in the two generator ducts always flowing in counter directions. The amount of liquid metal maintained in the ducts may be varied. This provides a variable stroke length for the pistons. The engine/generator provides variable AC power at variable frequencies that correspond to the power demands of the vehicular propulsion. Also the engine should maintain nearly constant efficiency throughout the range of power usage. Automobiles and trucks could be powered by the invention, with no transmission or power converter devices being required.

  4. Double-duct liquid metal magnetohydrodynamic engine

    DOE Patents [OSTI]

    Haaland, Carsten M. (Oak Ridge, TN)

    1997-01-01T23:59:59.000Z

    An internal combustion, liquid metal (LM) magnetohydrodynamic (MHD) engine and an alternating current (AC) magnetohydrodynamic generator, are used in combination to provide useful AC electric energy output. The engine design has four pistons and a double duct configuration, with each duct containing sodium potassium liquid metal confined between free pistons located at either end of the duct. The liquid metal is forced to flow back and forth in the duct by the movement of the pistons, which are alternatively driven by an internal combustion process. In the MHD generator, the two LM-MHD ducts pass in close proximity through a Hartmann duct with output transformer. AC power is produced by operating the engine with the liquid metal in the two generator ducts always flowing in counter directions. The amount of liquid metal maintained in the ducts may be varied. This provides a variable stroke length for the pistons. The engine/generator provides variable AC power at variable frequencies that correspond to the power demands of the vehicular propulsion. Also the engine should maintain nearly constant efficiency throughout the range of power usage. Automobiles and trucks could be powered by the invention, with no transmission or power converter devices being required.

  5. Charge transfer reactions in nematic liquid crystals

    SciTech Connect (OSTI)

    Wiederrecht, G.P. [Argonne National Lab., IL (United States). Chemistry Div.; Wasielewski, M.R. [Argonne National Lab., IL (United States). Chemistry Div.; [Northwestern Univ., Evanston, IL (United States). Dept. of Chemistry; Galili, T.; Levanon, H. [Hebrew Univ. of Jerusalem (Israel). Dept. of Physical Chemistry

    1998-07-01T23:59:59.000Z

    Ultrafast transient absorption studies of intramolecular photoinduced charge separation and thermal charge recombination were carried out on a molecule consisting of a 4-(N-pyrrolidino)naphthalene-1,8-imide donor (PNI) covalently attached to a pyromellitimide acceptor (PI) dissolved in the liquid crystal 4{prime}-(n-pentyl)-4-cyanobiphenyl (5CB). The temperature dependencies of the charge separation and recombination rates were obtained at temperatures above the nematic-isotropic phase transition of 5CB, where ordered microdomains exist and scattering of visible light by these domains is absent. The authors show that excited state charge separation is dominated by molecular reorientation of 5CB perpendicular to the director within the liquid crystal microdomains. They also show that charge recombination is adiabatic and is controlled by the comparatively slow collective reorientation of the liquid crystal microdomains relative to the orientation of PNI{sup +}-PI{sup {minus}}. They also report the results of time resolved electron paramagnetic resonance (TREPR) studies of photoinduced charge separation in a series of supramolecular compounds dissolved in oriented liquid crystal solvents. These studies permit the determination of the radical pair energy levels as the solvent reorganization energy increases from the low temperature crystalline phase, through the soft glass phase, to the nematic phase of the liquid crystal.

  6. Removal of arsenic compounds from petroliferous liquids

    DOE Patents [OSTI]

    Fish, R.H.

    1984-04-06T23:59:59.000Z

    The present invention in one aspect comprises a process for removing arsenic from petroliferous-derived liquids by contacting said liquid with a divinylbenzene-crosslinked polystyrene polymer (i.e. PS-DVB) having catechol ligands anchored to said polymer, said contacting being at an elevated temperature. In another aspect, the invention is a process for regenerating spent catecholated polystyrene polymer by removal of the arsenic bound to it from contacting petroliferous liquid in accordance with the aspect described above which regenerating process comprises: (a) treating said spent catecholated polystyrene polymer with an aqueous solution of at least one member selected from the group consisting of carbonates and bicarbonates of ammonium, alkali metals, and alkaline earth metals, said solution having a pH between about 8 and 10, and said treating being at a temperature in the range of about 20/sup 0/ to 100/sup 0/C; (b) separating the solids and liquids from each other. In a preferred embodiment the regeneration treatment is in two steps wherein step: (a) is carried out with an aqueous alcoholic carbonate solution which includes at least one lower alkyl alcohol, and, steps (c) and (d) are added. Steps (c) and (d) comprise: (c) treating the solids with an aqueous alcoholic solution of at least one ammonium, alkali or alkaline earth metal bicarbonate at a temperature in the range of about 20 to 100/sup 0/C; and (d) separating the solids from the liquids.

  7. Systems and methods for analyzing liquids under vacuum

    DOE Patents [OSTI]

    Yu, Xiao-Ying; Yang, Li; Cowin, James P.; Iedema, Martin J.; Zhu, Zihua

    2013-10-15T23:59:59.000Z

    Systems and methods for supporting a liquid against a vacuum pressure in a chamber can enable analysis of the liquid surface using vacuum-based chemical analysis instruments. No electrical or fluid connections are required to pass through the chamber walls. The systems can include a reservoir, a pump, and a liquid flow path. The reservoir contains a liquid-phase sample. The pump drives flow of the sample from the reservoir, through the liquid flow path, and back to the reservoir. The flow of the sample is not substantially driven by a differential between pressures inside and outside of the liquid flow path. An aperture in the liquid flow path exposes a stable portion of the liquid-phase sample to the vacuum pressure within the chamber. The radius, or size, of the aperture is less than or equal to a critical value required to support a meniscus of the liquid-phase sample by surface tension.

  8. High throughput liquid absorption preconcentrator sampling instrument

    DOE Patents [OSTI]

    Zaromb, Solomon (Hinsdale, IL); Bozen, Ralph M. (Hattiesburg, MS)

    1992-01-01T23:59:59.000Z

    A system for detecting trace concentrations of an analyte in air includes a preconcentrator for the analyte and an analyte detector. The preconcentrator includes an elongated tubular container comprising a wettable material. The wettable material is continuously wetted with an analyte-sorbing liquid which flows from one part of the container to a lower end. Sampled air flows through the container in contact with the wetted material with a swirling motion which results in efficient transfer of analyte vapors or aerosol particles to the sorbing liquid and preconcentration of traces of analyte in the liquid. The preconcentrated traces of analyte may be either detected within the container or removed therefrom for injection into a separate detection means or for subsequent analysis.

  9. Unreacted Hugoniots for porous and liquid explosives

    SciTech Connect (OSTI)

    Gustavsen, R.L.; Sheffield, S.A.

    1993-08-01T23:59:59.000Z

    Numerous authors have measured the Hugoniots of a variety of granular explosives pressed to different densities. Each explosive at each density was typically then treated as a unique material having its own Hugoniot. By combining methods used by Hayes, Sheffield and Mitchell (for describing the Hugoniot of HNS at various densities) with Hermann`s P-{alpha} model, it is only necessary to know some thermodynamic constants or the Hugoniot of the initially solid material and the porous material sound speed to obtain accurate unreacted Hugoniots for the porous explosive. We discuss application of this method to several materials including HMX, PETN, TNT, and Tetryl, as well as HNS. We also show that the ``Universal Liquid Hugoniot`` can be used to calculate the unreacted Hugoniot for liquid explosives. With this method only the ambient pressure sound speed and density are needed to predict the Hugoniot. Applications presented include nitromethane and liquid TNT.

  10. High throughput liquid absorption preconcentrator sampling instrument

    DOE Patents [OSTI]

    Zaromb, S.; Bozen, R.M.

    1992-12-22T23:59:59.000Z

    A system for detecting trace concentrations of an analyte in air includes a preconcentrator for the analyte and an analyte detector. The preconcentrator includes an elongated tubular container comprising a wettable material. The wettable material is continuously wetted with an analyte-sorbing liquid which flows from one part of the container to a lower end. Sampled air flows through the container in contact with the wetted material with a swirling motion which results in efficient transfer of analyte vapors or aerosol particles to the sorbing liquid and preconcentration of traces of analyte in the liquid. The preconcentrated traces of analyte may be either detected within the container or removed therefrom for injection into a separate detection means or for subsequent analysis. 12 figs.

  11. Liquid injection plasma deposition method and apparatus

    DOE Patents [OSTI]

    Kong, Peter C. (Idaho Falls, ID); Watkins, Arthur D. (Idaho Falls, ID)

    1999-01-01T23:59:59.000Z

    A liquid injection plasma torch deposition apparatus for depositing material onto a surface of a substrate may comprise a plasma torch for producing a jet of plasma from an outlet nozzle. A plasma confinement tube having an inlet end and an outlet end and a central bore therethrough is aligned with the outlet nozzle of the plasma torch so that the plasma jet is directed into the inlet end of the plasma confinement tube and emerges from the outlet end of the plasma confinement tube. The plasma confinement tube also includes an injection port transverse to the central bore. A liquid injection device connected to the injection port of the plasma confinement tube injects a liquid reactant mixture containing the material to be deposited onto the surface of the substrate through the injection port and into the central bore of the plasma confinement tube.

  12. Liquid injection plasma deposition method and apparatus

    DOE Patents [OSTI]

    Kong, P.C.; Watkins, A.D.

    1999-05-25T23:59:59.000Z

    A liquid injection plasma torch deposition apparatus for depositing material onto a surface of a substrate may comprise a plasma torch for producing a jet of plasma from an outlet nozzle. A plasma confinement tube having an inlet end and an outlet end and a central bore therethrough is aligned with the outlet nozzle of the plasma torch so that the plasma jet is directed into the inlet end of the plasma confinement tube and emerges from the outlet end of the plasma confinement tube. The plasma confinement tube also includes an injection port transverse to the central bore. A liquid injection device connected to the injection port of the plasma confinement tube injects a liquid reactant mixture containing the material to be deposited onto the surface of the substrate through the injection port and into the central bore of the plasma confinement tube. 8 figs.

  13. Separations by supported liquid membrane cascades

    DOE Patents [OSTI]

    Danesi, P.R.

    1983-09-01T23:59:59.000Z

    The invention describes a new separation technique which leads to multi-stage operations by the use of a series (a cascade) of alternated carrier-containing supported-liquid cation exchanger extractant and a liquid anion exchanger extractant (or a neutral extractant) as carrier. The membranes are spaced between alternated aqueous electrolytic solutions of different composition which alternatively provide positively charged extractable species and negatively charged (or zero charged) extractable species, of the chemical species to be separated. The alternated aqueous electrolytic solutions in addition to providing the driving force to the process, simultaneously function as a stripping solution from one type of membrane and as an extraction-promoting solution for the other type of membrane. The aqueous electrolytic solution and the supported liquid membranes are arranged to provide a continuous process.

  14. DOE studies on coal-to-liquids

    SciTech Connect (OSTI)

    NONE

    2007-07-01T23:59:59.000Z

    The US DOE National Energy Technology Laboratory has issued reports that examine the feasibility of coal-to-liquids (CTL) facilities, both general and site specific, which are available at www.netl.gov/energy-analyses/ref-shelf.html. The US Department of Defence has been investigating use of Fischer-Tropsch fuels. Congress is considering various CTL proposals while the private sector is building pilot plants and performing feasibility studies for proposed plants. The article includes a table listing 14 coal-to-liquids plants under consideration. The private sector has formed the coal-to-liquids coalition (www.futurecoalfuels.org). The article mentions other CTL projects in South Africa, China, Indonesia, the Philippines and New Zealand. 1 tab.

  15. Renormalization group flow for noncommutative Fermi liquids

    SciTech Connect (OSTI)

    Estrada-Jimenez, Sendic [Centro de Estudios en Fisica y Matematicas Basicas y Aplicadas, Universidad Autonoma de Chiapas, Calle 4a Oriente Norte 1428 Tuxtla Gutierrez, Chiapas (Mexico); Garcia-Compean, Hugo [Departamento de Fisica, Centro de Investigacion y de Estudios Avanzados del IPN P.O. Box 14-740, 07000 Mexico D.F. (Mexico); Wu Yongshi [Department of Physics and Astronomy, University of Utah Salt Lake City, Utah 84112 (United States); Department of Physics, Fudan University, Shanghai 200433 (China)

    2011-06-15T23:59:59.000Z

    Some recent studies of the AdS/CFT correspondence for condensed matter systems involve the Fermi liquid theory as a boundary field theory. Adding B-flux to the boundary D-branes leads in a certain limit to the noncommutative Fermi liquid, which calls for a field theory description of its critical behavior. As a preliminary step to more general consideration, the modification of the Landau's Fermi liquid theory due to noncommutativity of spatial coordinates is studied in this paper. We carry out the renormalization of interactions at tree level and one loop in a weakly coupled fermion system in two spatial dimensions. Channels ZS, ZS' and BCS are discussed in detail. It is shown that while the Gaussian fixed-point remains unchanged, the BCS instability is modified due to the space noncommutativity.

  16. Liquid Water Oceans in Ice Giants

    E-Print Network [OSTI]

    Sloane J. Wiktorowicz; Andrew P. Ingersoll

    2006-09-26T23:59:59.000Z

    Aptly named, ice giants such as Uranus and Neptune contain significant amounts of water. While this water cannot be present near the cloud tops, it must be abundant in the deep interior. We investigate the likelihood of a liquid water ocean existing in the hydrogen-rich region between the cloud tops and deep interior. Starting from an assumed temperature at a given upper tropospheric pressure (the photosphere), we follow a moist adiabat downward. The mixing ratio of water to hydrogen in the gas phase is small in the photosphere and increases with depth. The mixing ratio in the condensed phase is near unity in the photosphere and decreases with depth; this gives two possible outcomes. If at some pressure level the mixing ratio of water in the gas phase is equal to that in the deep interior, then that level is the cloud base. Alternately, if the mixing ratio of water in the condensed phase reaches that in the deep interior, then the surface of a liquid ocean will occur. We find that Neptune is both too warm (photospheric temperature too high) and too dry (mixing ratio of water in the deep interior too low) for liquid oceans to exist at present. To have a liquid ocean, Neptune's deep interior water to gas ratio would have to be higher than current models allow, and the density at 19 kbar would have to be ~ 0.8 g/cm^3. Such a high density is inconsistent with gravitational data obtained during the Voyager flyby. As Neptune cools, the probability of a liquid ocean increases. Extrasolar "hot Neptunes," which presumably migrate inward toward their parent stars, cannot harbor liquid water oceans unless they have lost almost all of the hydrogen and helium from their deep interiors.

  17. A method of measuring a molten metal liquid pool volume

    DOE Patents [OSTI]

    Garcia, G.V.; Carlson, N.M., Donaldson, A.D.

    1990-12-12T23:59:59.000Z

    A method of measuring a molten metal liquid pool volume and in particular molten titanium liquid pools, including the steps of (a) generating an ultrasonic wave at the surface of the molten metal liquid pool, (b) shining a light on the surface of a molten metal liquid pool, (c) detecting a change in the frequency of light, (d) detecting an ultrasonic wave echo at the surface of the molten metal liquid pool, and (e) computing the volume of the molten metal liquid. 3 figs.

  18. Anisotropic wave propagation in nematic liquid crystals

    E-Print Network [OSTI]

    Paolo Biscari; Antonio DiCarlo; Stefano S. Turzi

    2014-05-10T23:59:59.000Z

    Despite the fact that quantitative experimental data have been available for more than forty years now, nematoacoustics still poses intriguing theoretical and experimental problems. In this paper, we prove that the main observed features of acoustic wave propagation through a nematic liquid crystal cell -- namely, the anisotropy of sound velocity and its frequency dependence -- may be plausibly explained by a first-gradient continuum theory characterized by a hyperelastic anisotropic response from an evolving relaxed configuration. We compare and contrast our proposal with a competing theory where the liquid crystal is modeled as an isotropically compressible, anisotropic second-gradient fluid.

  19. Liquid additives for particulate emissions control

    DOE Patents [OSTI]

    Durham, Michael Dean (Castle Rock, CO); Schlager, Richard John (Aurora, CO); Ebner, Timothy George (Westminster, CO); Stewart, Robin Michele (Arvada, CO); Hyatt, David E. (Denver, CO); Bustard, Cynthia Jean (Littleton, CO); Sjostrom, Sharon (Denver, CO)

    1999-01-01T23:59:59.000Z

    The present invention discloses a process for removing undesired particles from a gas stream including the steps of contacting a composition containing an adhesive with the gas stream; collecting the undesired particles and adhesive on a collection surface to form an aggregate comprising the adhesive and undesired particles on the collection surface; and removing the agglomerate from the collection zone. The composition may then be atomized and injected into the gas stream. The composition may include a liquid that vaporizes in the gas stream. After the liquid vaporizes, adhesive particles are entrained in the gas stream. The process may be applied to electrostatic precipitators and filtration systems to improve undesired particle collection efficiency.

  20. ICARUS and Status of Liquid Argon Technology

    E-Print Network [OSTI]

    Dorota Stefan

    2011-10-07T23:59:59.000Z

    ICARUS is the largest liquid argon TPC detector ever built (~600 ton LAr mass). It operates underground at the LNGS laboratory in Gran Sasso. It has been smoothly running since summer 2010, collecting data with the CNGS beam and with cosmics. Liquid argon TPCs are really "electronic bubble chamber" providing a completely uniform imaging and calorimetry with unprecedented accuracy on massive volumes. ICARUS is internationally considered as a milestone towards the realization of the next generation of massive detectors (~tens of ktons) for neutrino and rare event physics. Results will be presented on the data collected during 2010 with the detector at LNGS.

  1. A Regenerable Filter for Liquid Argon Purification

    SciTech Connect (OSTI)

    Curioni, A.; Fleming, B.T.; /Yale U.; Jaskierny, W.; Kendziora, C.; Krider, J.; Pordes, S.; /Fermilab; Soderberg, Mitchell Paul; Spitz, J.; /Yale U.; Tope, T.; /Fermilab; Wongjirad, T.; /Yale U.

    2009-03-01T23:59:59.000Z

    A filter system for removing electronegative impurities from liquid argon is described. The active components of the filter are adsorbing molecular sieve and activated-copper-coated alumina granules. The system is capable of purifying liquid argon to an oxygen-equivalent impurity concentration of better than 30 parts per trillion, corresponding to an electron drift lifetime of at least 10 ms. Reduction reactions that occur at {approx} 250 C allow the filter material to be regenerated in situ through a simple procedure. In the following work we describe the filter design, performance, and regeneration process.

  2. Liquid Phases in SU(3) Chiral Perturbation Theory: Drops of Strange Chiral Nucleon Liquid & Ordinary Chiral Heavy Nuclear Liquid

    E-Print Network [OSTI]

    Bryan W. Lynn

    2010-05-12T23:59:59.000Z

    Chiral SU(3) Perturbation Theory (SU3XPT) identifies hadrons as the building blocks of strongly interacting matter at low densities and temperatures. We show that it admits two co-existing chiral nucleon liquid phases at zero external pressure with well-defined surfaces: 1) ordinary microscopic chiral heavy nuclear liquid drops (XNL) and 2) a new Strange Chiral Nucleon Liquid (SXNL) phase with both microscopic and macroscopic drop sizes. Liquid drops of both XNL and SXNL are simultaneously solutions to the SU3XPT semi-classical equations of motion and obey all relevant CVC and PCAC equations. Axial-vector currents are conserved inside macroscopic drops of SXNL, a new form of baryonic matter with zero electric charge density, which is by nature "dark". The numerical values of all SU3XPT coefficients are used to fit current scattering experiments and ordinary XNL drops (identified with the ground state of ordinary even-even spin-zero spherical closed-shell nuclei). SXNL then also emerges (i.e. without new adjustable parameters). For certain SU3XPT coefficients, finite microscopic and macroscopic drops of SXNL may be the ground state of a collection of nucleons: ordinary heavy nuclei may be meta-stable, while oceans of SXNL may force qualitative and experimentally observable changes to the neutron star equation of state.

  3. VOC and HAP recovery using ionic liquids

    SciTech Connect (OSTI)

    Michael R. Milota : Kaichang Li

    2007-05-29T23:59:59.000Z

    During the manufacture of wood composites, paper, and to a lesser extent, lumber, large amounts of volatile organic compounds (VOCs) such as terpenes, formaldehyde, and methanol are emitted to air. Some of these compounds are hazardous air pollutants (HAPs). The air pollutants produced in the forest products industry are difficult to manage because the concentrations are very low. Presently, regenerative thermal oxidizers (RTOs and RCOs) are commonly used for the destruction of VOCs and HAPs. RTOs consume large amounts of natural gas to heat air and moisture. The combustion of natural gas generates increased CO2 and NOx, which have negative implications for global warming and air quality. The aforementioned problems are addressed by an absorption system containing a room-temperature ionic liquid (RTIL) as an absorbent. RTILs are salts, but are in liquid states at room temperature. RTILs, an emerging technology, are receiving much attention as replacements for organic solvents in industrial processes with significant cost and environmental benefits. Some of these processes include organic synthesis, extraction, and metal deposition. RTILs would be excellent absorbents for exhausts from wood products facilities because of their unique properties: no measurable vapor pressure, high solubility of wide range of organic compounds, thermal stability to 200°C (almost 400°F), and immisciblity with water. Room temperature ionic liquids were tested as possible absorbents. Four were imidizolium-based and were eight phosphonium-based. The imidizolium-based ionic liquids proved to be unstable at the conditions tested and in the presence of water. The phosphonium-based ionic liquids were stable. Most were good absorbents; however, cleaning the contaminates from the ionic liquids was problematic. This was overcome with a higher temperature (120°C) than originally proposed and a very low pressure (1 kPa. Absorption trials were conducted with tetradecy(trihexyl)phosphonium dicyanamide as the RTIL. It was determined that it has good absorption properties for methanol and ?-pinene, is thermally stable, and is relatively easy to synthesize. It has a density of 0.89 g/mL at 20°C and a molecular weight of 549.9 g/mol. Trials were conducted with a small absorption system and a larger absorption system. Methanol, formaldehyde, and other HAPs were absorbed well, nearly 100%. Acetaldehyde was difficult to capture. Total VOC capture, while satisfactory on methanol and ?-pinene in a lab system, was less than expected in the field, 60-80%. The inability to capture the broad spectrum of total organics is likely due to difficulties in cleaning them from the ionic liquid rather than the ability of the ionic liquid to absorb. It’s likely that a commercial system could be constructed to remove 90 to 100% of the gas contaminates. Selecting the correct ionic liquid would be key to this. Absorption may not be the main selection criterion, but rather how easily the ionic liquid can be cleaned is very important. The ionic liquid absorption system might work very well in a system with a limited spectrum of pollutants, such as a paint spray line, where there are not very high molecular weight, non volatile, compounds in the exhaust.

  4. Liquid Fuels from Lignins: Annual Report

    SciTech Connect (OSTI)

    Chum, H. L.; Johnson, D. K.

    1986-01-01T23:59:59.000Z

    This task was initiated to assess the conversion of lignins into liquid fuels, primarily of lignins relevant to biomass-to-ethanol conversion processes. The task was composed of a literature review of this area and an experimental part to obtain pertinent data on the conversion of lignins germane to biomass-to-ethanol conversion processes.

  5. Supporting Information Liquid Crystalline Peptide Nanowires**

    E-Print Network [OSTI]

    Ihee, Hyotcherl

    1 Supporting Information Liquid Crystalline Peptide Nanowires** Tae Hee Han, Jangbae Kim, Ji Sun Park, Chan Beum Park, Hyotcherl Ihee,* and Sang Ouk Kim* #12;2 Figure S1. Size distribution of as orientation effect was also considered by using the March-Dollase function. The global isotropic temperature

  6. Improved liquid-film electron stripper

    DOE Patents [OSTI]

    Gavin, B.F.

    1984-11-01T23:59:59.000Z

    An improved liquid-film electron stripper particularly for high intensity heavy ion beams which produces constant regenerated, stable, free-standing liquid films having an adjustable thickness between 0.3 to 0.05 microns. The improved electron stripper is basically composed of at least one high speed, rotating disc with a very sharp, precision-like, ground edge on one side of the disc's periphery and with highly polished, flat, radial surface adjacent the sharp edge. A fine stream of liquid, such as oil, impinges at a 90/sup 0/ angle adjacent the disc's sharp outer edge. Film terminators, located at a selected distance from the disc perimeter are positioned approximately perpendicular to the film. The terminators support, shape, and stretch the film and are arranged to assist in the prevention of liquid droplet formation by directing the collected film to a reservoir below without breaking or interfering with the film. One embodiment utilizes two rotating discs and associated terminators, with the discs rotating so as to form films in opposite directions, and with the second disc being located down beam-line relative to the first disc.

  7. Local Energy Landscape in a Simple Liquid

    E-Print Network [OSTI]

    Takuya Iwashita; Takeshi Egami

    2014-10-31T23:59:59.000Z

    It is difficult to relate the properties of liquids and glasses directly to their structure because of complexity in the structure which defies precise definition. The potential energy landscape (PEL) approach is a very insightful way to conceptualize the structure-property relationship in liquids and glasses, particularly on the effect of temperature and history. However, because of the highly multi-dimensional nature of the PEL it is hard to determine, or even visualize, the actual details of the energy landscape. In this article we introduce a modified concept of the local energy landscape (LEL) which is limited in phase space, and demonstrate its usefulness using molecular dynamics simulation on a simple liquid at high temperatures. The local energy landscape is given as a function of the local coordination number, the number of the nearest neighbor atoms. The excitations in the LEL corresponds to the so-called beta-relaxation process. The LEL offers a simple but useful starting point to discuss complex phenomena in liquids and glasses.

  8. Liquid uranium alloy-helium fission reactor

    DOE Patents [OSTI]

    Minkov, Vladimir (Skokie, IL)

    1986-01-01T23:59:59.000Z

    This invention teaches a nuclear fission reactor having a core vessel and at least one tandem heat exchanger vessel coupled therewith across upper and lower passages to define a closed flow loop. Nuclear fuel such as a uranium alloy in its liquid phase fills these vessels and flow passages. Solid control elements in the reactor core vessel are adapted to be adjusted relative to one another to control fission reaction of the liquid fuel therein. Moderator elements in the other vessel and flow passages preclude fission reaction therein. An inert gas such as helium is bubbled upwardly through the heat exchanger vessel operable to move the liquid fuel upwardly therein and unidirectionally around the closed loop and downwardly through the core vessel. This helium gas is further directed to heat conversion means outside of the reactor vessels to utilize the heat from the fission reaction to generate useful output. The nuclear fuel operates in the 1200.degree.-1800.degree. C. range, and even higher to 2500.degree. C., limited only by the thermal effectiveness of the structural materials, increasing the efficiency of power generation from the normal 30-35% with 300.degree.-500.degree. C. upper limit temperature to 50-65%. Irradiation of the circulating liquid fuel, as contrasted to only localized irradiation of a solid fuel, provides improved fuel utilization.

  9. Discotic Liquid Crystals and Polymersomes: Molecule Goniometers

    E-Print Network [OSTI]

    Chang, Ya-Wen

    2012-10-19T23:59:59.000Z

    ................................ 6 1.2.4 Discotic Liquid Crystals ................................................... 9 1.2.5 Microfluidics .................................................................... 11 1.3. Dissertation Outline... ........................................................... 15 2.1.2 Di-block Copolymers, Lipids, and Particles .................... 15 2.1.3 Reactive Fluorophores ...................................................... 16 2.1.4 Surface Functionalization Chemicals...

  10. Combined plasma/liquid cleaning of substrates

    DOE Patents [OSTI]

    Selwyn, Gary S. (Los Alamos, NM); Henins, Ivars (Los Alamos, NM)

    2003-04-15T23:59:59.000Z

    Apparatus and method for cleaning substrates. A substrate is held and rotated by a chuck and an atmospheric pressure plasma jet places a plasma onto predetermined areas of the substrate. Subsequently liquid rinse is sprayed onto the predetermined areas. In one embodiment, a nozzle sprays a gas onto the predetermined areas to assist in drying the predetermined areas when needed.

  11. Program performs vapor-liquid equilibrium calculations

    SciTech Connect (OSTI)

    Rice, V.L.

    1982-06-28T23:59:59.000Z

    A program designed for the Hewlett-Packard HP-41CV or 41C calculators solves basic vapor-liquid equilibrium problems, including figuring the dewpoint, bubblepoint, and equilibrium flash. The algorithm uses W.C. Edmister's method for predicting ideal-solution K values.

  12. 1,2,3-triazolium ionic liquids

    DOE Patents [OSTI]

    Luebke, David; Nulwala, Hunaid; Tang, Chau

    2014-12-09T23:59:59.000Z

    The present invention relates to compositions of matter that are ionic liquids, the compositions comprising substituted 1,2,3-triazolium cations combined with any anion. Compositions of the invention should be useful in the separation of gases and, perhaps, as catalysts for many reactions.

  13. Separations by supported liquid membrane cascades

    DOE Patents [OSTI]

    Danesi, Pier R. (Clarendon Hills, IL)

    1986-01-01T23:59:59.000Z

    The invention describes a new separation technique which leads to multi-stage operations by the use of a series (a cascade) of alternated carrier-containing supported-liquid membranes. The membranes contain alternatively a liquid cation exchanger extractant and a liquid anion exchanger extractant (or a neutral extractant) as carrier. The membranes are spaced between alternated aqueous electrolytic solutions of different composition which alternatively provide positively charged extractable species and negatively charged (or zero charged) extractable species, of the chemical species to be separated. The alternated aqueous electrolytic solutions in addition to providing the driving force to the process, simultaneously function as a stripping solution from one type of membrane and as an extraction-promoting solution for the other type of membrane. The aqueous electrolytic solutions and the supported liquid membranes are arranged in such a way to provide a continuous process which leads to the continuous enrichment of the species which show the highest permeability coefficients. By virtue of the very high number of stages which can be arranged, even chemical species having very similar chemical behavior (and consequently very similar permeability coefficients) can be completely separated. The invention also provide a way to concentrate the separated species.

  14. Performance Characteristics of Coal-to-Liquids (CTL) Diesel in...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Characteristics of Coal-to-Liquids (CTL) Diesel in a 50-State Emissions Compliant Passenger Car Performance Characteristics of Coal-to-Liquids (CTL) Diesel in a 50-State Emissions...

  15. System for removing liquid waste from a tank

    DOE Patents [OSTI]

    Meneely, Timothy K. (Penn Hills, PA); Sherbine, Catherine A. (N. Versailles Township, Allegheny County, PA)

    1994-01-01T23:59:59.000Z

    A tank especially suited for nuclear applications is disclosed. The tank comprises a tank shell for protectively surrounding the liquid contained therein; an inlet positioned on the tank for passing a liquid into the tank; a sump positioned in an interior portion of the tank for forming a reservoir of the liquid; a sloped incline for resting the tank thereon and for creating a natural flow of the liquid toward the sump; a pump disposed adjacent the tank for pumping the liquid; and a pipe attached to the pump and extending into the sump for passing the liquid therethrough. The pump pumps the liquid in the sump through the pipe and into the pump for discharging the liquid out of the tank.

  16. On the Fluctuations that Order and Frustrate Liquid Water

    E-Print Network [OSTI]

    Limmer, David

    2013-01-01T23:59:59.000Z

    the forces of hydrogen bonds to the properties of liquid andhydrogen bond network couples to the dynamically heterogeneous propertiesproperties of liquid water manifest how the strength of these hydrogen

  17. Adsorption of Polypropylene and Polyethylene on Liquid Chromatographic

    E-Print Network [OSTI]

    Li, Jing

    Adsorption of Polypropylene and Polyethylene on Liquid Chromatographic Column Packings T. Macko1 tested as column packings for adsorption of isotactic polypropylene and linear polyethylene from dilute sorbent - mobile phase, where adsorption of polypropylene was observed. Keywords Column liquid

  18. System for removing liquid waste from a tank

    DOE Patents [OSTI]

    Meneely, T.K.; Sherbine, C.A.

    1994-04-26T23:59:59.000Z

    A tank especially suited for nuclear applications is disclosed. The tank comprises a tank shell for protectively surrounding the liquid contained therein; an inlet positioned on the tank for passing a liquid into the tank; a sump positioned in an interior portion of the tank for forming a reservoir of the liquid; a sloped incline for resting the tank thereon and for creating a natural flow of the liquid toward the sump; a pump disposed adjacent the tank for pumping the liquid; and a pipe attached to the pump and extending into the sump for passing the liquid there through. The pump pumps the liquid in the sump through the pipe and into the pump for discharging the liquid out of the tank. 2 figures.

  19. area liquid lithium: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    liquid lithium plasma-facing surface will be used 11 Waste-Lithium-Liquid (WLL) Flow Battery for Stationary Energy Storage Applications Youngsik Kim* and Nina MahootcheianAsl...

  20. Systems and methods for monitoring a solid-liquid interface

    DOE Patents [OSTI]

    Stoddard, Nathan G; Lewis, Monte A.; Clark, Roger F

    2013-06-11T23:59:59.000Z

    Systems and methods are provided for monitoring a solid-liquid interface during a casting process. The systems and methods enable determination of the location of a solid-liquid interface during the casting process.

  1. advanced liquid metal: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    14 15 16 17 18 19 20 21 22 23 24 25 Next Page Last Page Topic Index 1 Liquid Metal Transformers CERN Preprints Summary: The room temperature liquid metal is quickly emerging as an...

  2. Household Need for Liquidity and the Credit Card Debt Puzzle

    E-Print Network [OSTI]

    Telyukova, Irina

    2008-01-01T23:59:59.000Z

    on credit cards; “save” to saving in liquid assets. Creditgroups) Savings accounts (avg. across groups) Borrow & Savesave for retirement in retirement accounts, emergencies, including home-related ones, by their de?nition are likely to require liquid savings.

  3. Modeling the operating voltage of liquid metal battery cells

    E-Print Network [OSTI]

    Newhouse, Jocelyn Marie

    2014-01-01T23:59:59.000Z

    A one-dimensional, integrative model of the voltage during liquid metal battery operation has been developed to enhance the understanding of performance at the cell level. Two liquid metal batteries were studied: Mg-Sb for ...

  4. Engineering-Scale Liquid Cadmium Cathode Experiments

    SciTech Connect (OSTI)

    D Vaden; B. R. Westphal; S. X. Li; T. A. Johnson; K. B. Davies; D. M. Pace

    2006-08-01T23:59:59.000Z

    Recovery of transuranic actinides (TRU) using electrorefining is a process being investigated as part of the Department of Energy (DOE) Advanced Fuel Cycle Initiative (AFCI). TRU recovery via electrorefining onto a solid cathode is very difficult as the thermodynamic properties of transuranics are not favourable for them to remain in the metal phase while significant quantities of uranium trichloride exist in the electrolyte. Theoretically, the concentration of transuranics in the electrolyte must be approximately 106 greater than the uranium concentration in the electrolyte to produce a transuranic deposit on a solid cathode. Using liquid cadmium as a cathode contained within a LiCl-KCl eutectic salt, the co-deposition of uranium and transuranics is feasible because the activity of the transuranics in liquid cadmium is very small. Depositing transuranics and uranium in a liquid cadmium cathode (LCC) theoretically requires the concentration of transuranics to be two to three times the uranium concentration in the electrolyte. Three LCC experiments were performed in an Engineering scale elecdtrorefiner, which is located in the argon hot cell of the Fuel Conditioning Facility at the Materials and Fuels Complex on the Idaho National Laboratory. Figure 1 contains photographs of the LCC assembly in the hot cell prior to the experiment and a cadmium ingot produced after the first LCC test. Figure 1. Liquid Cadmium Cathode (left) and Cadmium Ingot (right) The primary goal of the engineering-scale liquid cadmium cathode experiments was to electrochemically collect kilogram quantities of uranium and plutonium via a LCC. The secondary goal was to examine fission product contaminations in the materials collected by the LCC. Each LCC experiment used chopped spent nuclear fuel from the blanket region of the Experimental Breeder Reactor II loaded into steel baskets as the anode with the LCC containing 26 kg of cadmium metal. In each experiment, between one and two kilograms of heavy metal was collected in the LCC after passing an integrated current over 500 amp hours. Analysis of samples from the liquid cadmium cathode ingots showed detectable amounts of transuranics and rare-earth elements. Acknowledgements K. B. Davies and D. M. Pace for the mechanical and electrical engineering needed to prepare the equipment for the engineering-scale liquid cadmium cathode experiments.

  5. Dependence of solid-liquid interface free energy on liquid structure

    SciTech Connect (OSTI)

    Wilson, S R [Ames Laboratory; Mendelev, M I [Ames Laboratory

    2014-09-01T23:59:59.000Z

    The Turnbull relation is widely believed to enable prediction of solid–liquid interface (SLI) free energies from measurements of the latent heat and the solid density. Ewing proposed an additional contribution to the SLI free energy to account for variations in liquid structure near the interface. In the present study, molecular dynamics (MD) simulations were performed to investigate whether SLI free energy depends on liquid structure. Analysis of the MD simulation data for 11 fcc metals demonstrated that the Turnbull relation is only a rough approximation for highly ordered liquids, whereas much better agreement is observed with Ewing’s theory. A modification to Ewing’s relation is proposed in this study that was found to provide excellent agreement with MD simulation data.

  6. Laser capillary spectrophotometric acquisition of bivariate drop size and concentration data for liquid-liquid dispersion

    DOE Patents [OSTI]

    Tavlarides, L.L.; Bae, J.H.

    1991-12-24T23:59:59.000Z

    A laser capillary spectrophotometric technique measures real time or near real time bivariate drop size and concentration distribution for a reactive liquid-liquid dispersion system. The dispersion is drawn into a precision-bore glass capillary and an appropriate light source is used to distinguish the aqueous phase from slugs of the organic phase at two points along the capillary whose separation is precisely known. The suction velocity is measured, as is the length of each slug from which the drop free diameter is calculated. For each drop, the absorptivity at a given wavelength is related to the molar concentration of a solute of interest, and the concentration of given drops of the organic phase is derived from pulse heights of the detected light. This technique permits on-line monitoring and control of liquid-liquid dispersion processes. 17 figures.

  7. MagViz Bottled Liquid Scanner at Albuquerque International Sunport

    ScienceCinema (OSTI)

    Surko, Stephen; Dennis, Steve; Espy, Michelle

    2014-08-12T23:59:59.000Z

    The next-generation bottled liquid scanner, MagViz BLS, is demonstrated at the Albuquerque International Sunport, New Mexico

  8. Metal-air low temperature ionic liquid cell

    DOE Patents [OSTI]

    Friesen, Cody A; Buttry, Daniel A

    2014-11-25T23:59:59.000Z

    The present application relates to an electrochemical metal-air cell in which a low temperature ionic liquid is used.

  9. Plasmas in Multiphase Media: Bubble Enhanced Discharges in Liquids and Plasma/Liquid Phase Boundaries

    SciTech Connect (OSTI)

    Kushner, Mark Jay [University of Michigan] [University of Michigan

    2014-07-10T23:59:59.000Z

    In this research project, the interaction of atmospheric pressure plasmas with multi-phase media was computationally investigated. Multi-phase media includes liquids, particles, complex materials and porous surfaces. Although this investigation addressed fundamental plasma transport and chemical processes, the outcomes directly and beneficially affected applications including biotechnology, medicine and environmental remediation (e.g., water purification). During this project, we made advances in our understanding of the interaction of atmospheric pressure plasmas in the form of dielectric barrier discharges and plasma jets with organic materials and liquids. We also made advances in our ability to use computer modeling to represent these complex processes. We determined the method that atmospheric pressure plasmas flow along solid and liquid surfaces, and through endoscopic like tubes, deliver optical and high energy ion activation energy to organic and liquid surfaces, and produce reactivity in thin liquid layers, as might cover a wound. We determined the mechanisms whereby plasmas can deliver activation energy to the inside of liquids by sustaining plasmas in bubbles. These findings are important to the advancement of new technology areas such as plasma medicine

  10. Liquid Lithium Limiter Effects on Tokamak Plasmas and Plasma-Liquid Surface Interactions

    SciTech Connect (OSTI)

    R. Kaita; R. Majeski; R. Doerner; G. Antar; M. Baldwin; R. Conn; P. Efthimion; M. Finkenthal; D. Hoffman; B. Jones; S. Krashenninikov; H. Kugel; S. Luckhardt; R. Maingi; J. Menard; T. Munsat; D. Stutman; G. Taylor; J. Timberlake; V. Soukhanovskii; D. Whyte; R. Woolley; L. Zakharov

    2002-10-15T23:59:59.000Z

    We present results from the first experiments with a large area liquid lithium limiter in a magnetic fusion device, and its effect on improving plasma performance by reducing particle recycling. Using large area liquid metal surfaces in any major fusion device is unlikely before a test on a smaller scale. This has motivated its demonstration in the CDX-U spherical torus with a unique, fully toroidal lithium limiter. The highest current discharges were obtained with a liquid lithium limiter. There was a reduction in recycling, as indicated by a significant decrease in the deuterium-alpha emission and oxygen radiation. How these results might extrapolate to reactors is suggested in recycling/retention experiments with liquid lithium surfaces under high-flux deuterium and helium plasma bombardment in PISCES-B. Data on deuterium atoms retained in liquid lithium indicate retention of all incident ions until full volumetric conversion to lithium deuteride. The PISCES-B results also show a material loss mechanism that lowers the maximum operating temperature compared to that for the liquid surface equilibrium vapor pressure. This may restrict the lithium temperature in reactors.

  11. NATURAL CONVECTION OF SUBCOOLED LIQUID NITROGEN IN A VERTICAL CAVITY

    E-Print Network [OSTI]

    Chang, Ho-Myung

    temperature superconductor) power devices, such as HTS transformers, fault current limiters, and terminals power transformer cooled by natural convection of subcooled liquid nitrogen. A liquid nitrogen bath of subcooled liquid nitrogen system for an HTS transformer, operating at around 65 K. This system consists

  12. Electrohydrodynamically driven large-area liquid ion sources

    DOE Patents [OSTI]

    Pregenzer, Arian L. (Corrales, NM)

    1988-01-01T23:59:59.000Z

    A large-area liquid ion source comprises means for generating, over a large area of the surface of a liquid, an electric field of a strength sufficient to induce emission of ions from a large area of said liquid. Large areas in this context are those distinct from emitting areas in unidimensional emitters.

  13. Cost of meeting geothermal liquid effluent disposal regulations

    SciTech Connect (OSTI)

    Wells, K.D.; Currie, J.W.; Price, B.A.; Rogers, E.A.

    1981-06-01T23:59:59.000Z

    Background information is presented on the characteristics of liquid wastes and the available disposal options. Regulations that may directly or indirectly influence liquid waste disposal are reviewed. An assessment of the available wastewater-treatment systems is provided. A case study of expected liquid-waste-treatment and disposal costs is summarized. (MHR)

  14. (Electron transfer rates at semiconductor/liquid interfaces)

    SciTech Connect (OSTI)

    Lewis, N.S.

    1992-01-01T23:59:59.000Z

    Work has focused on several aspects of the fundamental chemistry and physics semiconductor/liquid junction behavior. These projects have been directed primarily towards GaAs/liquid contacts, because GaAs/liquid systems provide high energy conversion efficiencies and offer an opportunity to gain mechanistic understanding of the factors that are important to control in an efficient photoelectrochemical energy conversion system.

  15. [Electron transfer rates at semiconductor/liquid interfaces]. Progress report

    SciTech Connect (OSTI)

    Lewis, N.S.

    1992-08-01T23:59:59.000Z

    Work has focused on several aspects of the fundamental chemistry and physics semiconductor/liquid junction behavior. These projects have been directed primarily towards GaAs/liquid contacts, because GaAs/liquid systems provide high energy conversion efficiencies and offer an opportunity to gain mechanistic understanding of the factors that are important to control in an efficient photoelectrochemical energy conversion system.

  16. Long range forces between atomic impurities in liquid helium

    E-Print Network [OSTI]

    Long range forces between atomic impurities in liquid helium J. Dupont-Roc Laboratoire Kastler in a polarizable medium. We show that atomic impurities in liquid helium may indeed realize repulsive forces embedded in liquid helium, super uid or not. Solid helium have also been used. Successful theoretical

  17. Liquid crystals and Q-tensors The free energy

    E-Print Network [OSTI]

    Segatti, Antonio

    Liquid crystals and Q-tensors The free energy A temperature-dependent model Mathematical results #12;Liquid crystals and Q-tensors The free energy A temperature-dependent model Mathematical results, Non-isothermal nematic liquid crystals flows with the Ball-Majumdar free energy, Ann. Mat. Pura Appl

  18. RF cavity using liquid dielectric for tuning and cooling

    DOE Patents [OSTI]

    Popovic, Milorad (Warrenville, IL); Johnson, Rolland P. (Newport News, VA)

    2012-04-17T23:59:59.000Z

    A system for accelerating particles includes an RF cavity that contains a ferrite core and a liquid dielectric. Characteristics of the ferrite core and the liquid dielectric, among other factors, determine the resonant frequency of the RF cavity. The liquid dielectric is circulated to cool the ferrite core during the operation of the system.

  19. High air volume to low liquid volume aerosol collector

    DOE Patents [OSTI]

    Masquelier, Donald A. (Tracy, CA); Milanovich, Fred P. (Lafayette, CA); Willeke, Klaus (Cincinnati, OH)

    2003-01-01T23:59:59.000Z

    A high air volume to low liquid volume aerosol collector. A high volume flow of aerosol particles is drawn into an annular, centripetal slot in a collector which directs the aerosol flow into a small volume of liquid pool contained is a lower center section of the collector. The annular jet of air impinges into the liquid, imbedding initially airborne particles in the liquid. The liquid in the pool continuously circulates in the lower section of the collector by moving to the center line, then upwardly, and through assistance by a rotating deflector plate passes back into the liquid at the outer area adjacent the impinging air jet which passes upwardly through the liquid pool and through a hollow center of the collector, and is discharged via a side outlet opening. Any liquid droplets escaping with the effluent air are captured by a rotating mist eliminator and moved back toward the liquid pool. The collector includes a sensor assembly for determining, controlling, and maintaining the level of the liquid pool, and includes a lower centrally located valve assembly connected to a liquid reservoir and to an analyzer for analyzing the particles which are impinged into the liquid pool.

  20. Tribological Properties of Ionic Liquids Lubricants Containing Nanoparticles

    E-Print Network [OSTI]

    Lu, Wei

    2014-05-14T23:59:59.000Z

    and with organic solvents and electrochemical properties [7]. Because of these properties ionic liquids become a new green solvent or lubricant in industrial application. 1.2.2 The application of ionic liquid in tribology 1.2.2.1 Ionic liquids as lubrication...

  1. Energy Landscape Diversity and Supercooled Liquid Properties Frank H. Stillingera

    E-Print Network [OSTI]

    Stillinger, Frank

    typically exhibit little difference between liquid and crystal heat capacities Cp , and tend to have of the latter have liquid heat capacities that are significantly larger than the corresponding crystal values of the so-called "Kauzmann paradox". 5 The supercooled-liquid versus crystal heat capacity discrepancy, when

  2. The physics of liquid water Bernard Cabane1

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    with extraordinary properties: it has unusually high melting and boiling temperatures, a huge heat capacity, oneThe physics of liquid water Bernard Cabane1 , Rodolphe Vuilleumier2 1 PMMH, ESPCI, 10 rue Vauquelin, France Abstract Liquid water is a liquid with extraordinary properties: it has a very high cohesion

  3. A Microfluidic System for the Continuous Recycling of Unmodified Homogeneous Palladium Catalysts through Liquid/Liquid Phase Separation

    E-Print Network [OSTI]

    Li, Pengfei

    A prototype microflow system for the continuous recycling of homogeneous catalysts through liquid/liquid phase separation was developed and its effectiveness demonstrated in a challenging palladium-catalyzed hydroxylation ...

  4. Liquid-Liquid Phase Transition in Confined Water: A Monte Carlo Study Martin Meyer and H. Eugene Stanley*

    E-Print Network [OSTI]

    Stanley, H. Eugene

    Liquid-Liquid Phase Transition in Confined Water: A Monte Carlo Study Martin Meyer and H. Eugene Stanley* Center for Polymer Studies and Department of Physics, Boston UniVersity, Boston, Massachusetts

  5. Sum frequency generation study on the orientation of room-temperature ionic liquid at the grapheneionic liquid interface

    E-Print Network [OSTI]

    Bao, Jiming

    such as dye-sensitized solar cells and super capacitors, room-temperature ionic liquids are considered

  6. Experimental partitioning of uranium between liquid iron sulfide and liquid silicate: Implications for radioactivity in the Earth's core

    E-Print Network [OSTI]

    Minarik, William

    Experimental partitioning of uranium between liquid iron sulfide and liquid silicate: Implications Measurable uranium (U) is found in metal sulfide liquids in equilibrium with molten silicate at conditions shows that K is depleted in the Earth by $50%, while U and Th are slightly enriched (Palme and O

  7. Method and apparatus for destroying organic contaminants in aqueous liquids

    DOE Patents [OSTI]

    Donaldson, Terrence L. (Lenior City, TN); Wilson, James H. (Oak Ridge, TN)

    1993-01-01T23:59:59.000Z

    A method and apparatus for destroying organic contaminants, such as trichloroethylene, in aqueous liquids, such as groundwater, utilizing steam stripping integrated with biodegradation. The contaminated aqueous liquid is fed into a steam stripper causing the volatilization of essentially all of the organic contaminants and a portion of the aqueous liquid. The majority of the aqueous liquid is discharged from the steam stripper. The volatilized vapors are then condensed to the liquid phase and introduced into a bioreactor. The bioreactor contains methanotrophic microorganisms which convert the organic contaminants into mainly carbon dioxide. The effluent from the bioreactor is then recycled back to the steam stripper for further processing.

  8. Method and apparatus for destroying organic contaminants in aqueous liquids

    DOE Patents [OSTI]

    Donaldson, T.L.; Wilson, J.H.

    1993-09-21T23:59:59.000Z

    A method and apparatus for destroying organic contaminants, such as trichloroethylene, in aqueous liquids, such as groundwater, utilizing steam stripping integrated with biodegradation. The contaminated aqueous liquid is fed into a steam stripper causing the volatilization of essentially all of the organic contaminants and a portion of the aqueous liquid. The majority of the aqueous liquid is discharged from the steam stripper. The volatilized vapors are then condensed to the liquid phase and introduced into a bioreactor. The bioreactor contains methanotrophic microorganisms which convert the organic contaminants into mainly carbon dioxide. The effluent from the bioreactor is then recycled back to the steam stripper for further processing. 2 figures.

  9. Methods of hydrotreating a liquid stream to remove clogging compounds

    DOE Patents [OSTI]

    Minderhoud, Johannes Kornelis [Amsterdam, NL; Nelson, Richard Gene [Katy, TX; Roes, Augustinus Wilhelmus Maria [Houston, TX; Ryan, Robert Charles [Houston, TX; Nair, Vijay [Katy, TX

    2009-09-22T23:59:59.000Z

    A method includes producing formation fluid from a subsurface in situ heat treatment process. The formation fluid is separated to produce a liquid stream and a gas stream. At least a portion of the liquid stream is provided to a hydrotreating unit. At least a portion of selected in situ heat treatment clogging compositions in the liquid stream are removed to produce a hydrotreated liquid stream by hydrotreating at least a portion of the liquid stream at conditions sufficient to remove the selected in situ heat treatment clogging compositions.

  10. Use of ionic liquids as coordination ligands for organometallic catalysts

    DOE Patents [OSTI]

    Li, Zaiwei (Moreno Valley, CA); Tang, Yongchun (Walnut, CA); Cheng; Jihong (Arcadia, CA)

    2009-11-10T23:59:59.000Z

    Aspects of the present invention relate to compositions and methods for the use of ionic liquids with dissolved metal compounds as catalysts for a variety of chemical reactions. Ionic liquids are salts that generally are liquids at room temperature, and are capable of dissolving a many types of compounds that are relatively insoluble in aqueous or organic solvent systems. Specifically, ionic liquids may dissolve metal compounds to produce homogeneous and heterogeneous organometallic catalysts. One industrially-important chemical reaction that may be catalyzed by metal-containing ionic liquid catalysts is the conversion of methane to methanol.

  11. Methods and systems for monitoring a solid-liquid interface

    DOE Patents [OSTI]

    Stoddard, Nathan G. (Gettysburg, PA); Clark, Roger F. (Frederick, MD); Kary, Tim (Union Bridge, MD)

    2010-07-20T23:59:59.000Z

    Methods and systems are provided for monitoring a solid-liquid interface, including providing a vessel configured to contain an at least partially melted material; detecting radiation reflected from a surface of a liquid portion of the at least partially melted material that is parallel with the liquid surface; measuring a disturbance on the surface; calculating at least one frequency associated with the disturbance; and determining a thickness of the liquid portion based on the at least one frequency, wherein the thickness is calculated based on.times. ##EQU00001## where g is the gravitational constant, w is the horizontal width of the liquid, and f is the at least one frequency.

  12. Heat capacity of liquids: an approach from the solid phase

    E-Print Network [OSTI]

    Kostya Trachenko

    2008-08-20T23:59:59.000Z

    We calculate the energy and heat capacity of a liquid on the basis of its elastic properties and vibrational states. The experimental decrease of liquid heat capacity with temperature is attributed to the increasing loss of two transverse modes with frequency $\\omegaliquid relaxation time. In a simple model, liquid heat capacity is related to viscosity and is compared with the experimental data of mercury. We also calculate the vibrational energy of a quantum liquid, and show that transverse phonons can not be excited in the low-temperature limit. Finally, we discuss the implications of the proposed approach to liquids for the problem of glass transition.

  13. Comments on Fermi Liquid from Holography

    E-Print Network [OSTI]

    Manuela Kulaxizi; Andrei Parnachev

    2008-10-13T23:59:59.000Z

    We investigate the signatures of Fermi liquid formation in the N=4 super Yang-Mills theory coupled to fundamental hypermultiplet at nonvanishing chemical potential for the global U(1) vector symmetry. At strong 't Hooft coupling the system can be analyzed in terms of the D7 brane dynamics in AdS_5 x S^5 background. The phases with vanishing and finite charge density are separated at zero temperature by a quantum phase transition. In case of vanishing hypermultiplet mass, Karch, Son and Starinets discovered a gapless excitation whose speed equals the speed of sound. We find that this zero sound mode persists to all values of the hypermultiplet mass, and its speed vanishes at the point of phase transition. The value of critical exponent and the ratio of the velocities of zero and first sounds are consistent with the predictions of Landau Fermi liquid theory at strong coupling.

  14. Comments on Fermi Liquid from Holography

    E-Print Network [OSTI]

    Kulaxizi, Manuela

    2008-01-01T23:59:59.000Z

    We investigate the signatures of Fermi liquid formation in the N=4 super Yang-Mills theory coupled to fundamental hypermultiplet at nonvanishing chemical potential for the global U(1) vector symmetry. At strong 't Hooft coupling the system can be analyzed in terms of the D7 brane dynamics in AdS_5 x S^5 background. The phases with vanishing and finite charge density are separated at zero temperature by a quantum phase transition. In case of vanishing hypermultiplet mass, Karch, Son and Starinets discovered a gapless excitation whose speed equals the speed of sound. We find that this zero sound mode persists to all values of the hypermultiplet mass, and its speed vanishes at the point of phase transition. The value of critical exponent and the ratio of the velocities of zero and first sounds are consistent with the predictions of Landau Fermi liquid theory at strong coupling.

  15. Kinetics of complex plasma with liquid droplets

    SciTech Connect (OSTI)

    Misra, Shikha; Sodha, M. S. [Centre of Energy Studies, Indian Institute of Technology Delhi (IITD), New Delhi 110016 (India)] [Centre of Energy Studies, Indian Institute of Technology Delhi (IITD), New Delhi 110016 (India); Mishra, S. K. [Institute for Plasma Research (IPR), Gandhinagar 382428 (India)] [Institute for Plasma Research (IPR), Gandhinagar 382428 (India)

    2013-12-15T23:59:59.000Z

    This paper provides a theoretical basis for the reduction of electron density by spray of water (or other liquids) in hot plasma. This phenomenon has been observed in a hypersonic flight experiment for relief of radio black out, caused by high ionization in the plasma sheath of a hypersonic vehicle, re-entering the atmosphere. The analysis incorporates a rather little known phenomenon for de-charging of the droplets, viz., evaporation of ions from the surface and includes the charge balance on the droplets and number cum energy balance of electrons, ions, and neutral molecules; the energy balance of the evaporating droplets has also been taken into account. The analysis has been applied to a realistic situation and the transient variations of the charge and radius of water droplets, and other plasma parameters have been obtained and discussed. The analysis through made in the context of water droplets is applicable to all liquids.

  16. Ionic Liquid Membranes for Carbon Dioxide Separation

    SciTech Connect (OSTI)

    Myers, C.R.; Ilconich, J.B.; Luebke, D.R.; Pennline, H.W.

    2008-07-12T23:59:59.000Z

    Recent scientific studies are rapidly advancing novel technological improvements and engineering developments that demonstrate the ability to minimize, eliminate, or facilitate the removal of various contaminants and green house gas emissions in power generation. The Integrated Gasification Combined Cycle (IGCC) shows promise for carbon dioxide mitigation not only because of its higher efficiency as compared to conventional coal firing plants, but also due to a higher driving force in the form of high partial pressure. One of the novel technological concepts currently being developed and investigated is membranes for carbon dioxide (CO2) separation, due to simplicity and ease of scaling. A challenge in using membranes for CO2 capture in IGCC is the possibility of failure at elevated temperatures or pressures. Our earlier research studies examined the use of ionic liquids on various supports for CO2 separation over the temperature range, 37°C-300°C. The ionic liquid, 1-hexyl-3methylimidazolium Bis(trifluoromethylsulfonyl)imide, ([hmim][Tf2N]), was chosen for our initial studies with the following supports: polysulfone (PSF), poly(ether sulfone) (PES), and cross-linked nylon. The PSF and PES supports had similar performance at room temperature, but increasing temperature caused the supported membranes to fail. The ionic liquid with the PES support greatly affected the glass transition temperature, while with the PSF, the glass transition temperature was only slightly depressed. The cross-linked nylon support maintained performance without degradation over the temperature range 37-300°C with respect to its permeability and selectivity. However, while the cross-linked nylon support was able to withstand temperatures, the permeability continued to increase and the selectivity decreased with increasing temperature. Our studies indicated that further testing should examine the use of other ionic liquids, including those that form chemical complexes with CO2 based on amine interactions. The hypothesis is that the performance at the elevated temperatures could be improved by allowing a facilitated transport mechanism to become dominant. Several amine-based ionic liquids were tested on the cross-linked nylon support. It was found that using the amine-based ionic liquid did improve selectivity and permeability at higher temperature. The hypothesis was confirmed, and it was determined that the type of amine used also played a role in facilitated transport. Given the appropriate aminated ionic liquid with the cross-linked nylon support, it is possible to have a membrane capable of separating CO2 at IGCC conditions. With this being the case, the research has expanded to include separation of other constituents besides CO2 (CO, H2S, etc.) and if they play a role in membrane poisoning or degradation. This communication will discuss the operation of the recently fabricated ionic liquid membranes and the impact of gaseous components other than CO2 on their performance and stability.

  17. Liquid additives for particulate emissions control

    DOE Patents [OSTI]

    Durham, M.D.; Schlager, R.J.; Ebner, T.G.; Stewart, R.M.; Hyatt, D.E.; Bustard, C.J.; Sjostrom, S.

    1999-01-05T23:59:59.000Z

    The present invention discloses a process for removing undesired particles from a gas stream including the steps of contacting a composition containing an adhesive with the gas stream; collecting the undesired particles and adhesive on a collection surface to form an aggregate comprising the adhesive and undesired particles on the collection surface; and removing the agglomerate from the collection zone. The composition may then be atomized and injected into the gas stream. The composition may include a liquid that vaporizes in the gas stream. After the liquid vaporizes, adhesive particles are entrained in the gas stream. The process may be applied to electrostatic precipitators and filtration systems to improve undesired particle collection efficiency. 11 figs.

  18. Ultrasonic characterization of single drops of liquids

    DOE Patents [OSTI]

    Sinha, Dipen N. (Los Alamos, NM)

    1998-01-01T23:59:59.000Z

    Ultrasonic characterization of single drops of liquids. The present invention includes the use of two closely spaced transducers, or one transducer and a closely spaced reflector plate, to form an interferometer suitable for ultrasonic characterization of droplet-size and smaller samples without the need for a container. The droplet is held between the interferometer elements, whose distance apart may be adjusted, by surface tension. The surfaces of the interferometer elements may be readily cleansed by a stream of solvent followed by purified air when it is desired to change samples. A single drop of liquid is sufficient for high-quality measurement. Examples of samples which may be investigated using the apparatus and method of the present invention include biological specimens (tear drops; blood and other body fluid samples; samples from tumors, tissues, and organs; secretions from tissues and organs; snake and bee venom, etc.) for diagnostic evaluation, samples in forensic investigations, and detection of drugs in small quantities.

  19. Equilibrium composition between liquid and clathrate reservoirs on Titan

    E-Print Network [OSTI]

    Mousis, Olivier; Lunine, Jonathan I; Sotin, Christophe

    2015-01-01T23:59:59.000Z

    Hundreds of lakes and a few seas of liquid hydrocarbons have been observed by the Cassini spacecraft to cover the polar regions of Titan. A significant fraction of these lakes or seas could possibly be interconnected with subsurface liquid reservoirs of alkanes. In this paper, we investigate the interplay that would happen between a reservoir of liquid hydrocarbons located in Titan's subsurface and a hypothetical clathrate reservoir that progressively forms if the liquid mixture diffuses throughout a preexisting porous icy layer. To do so, we use a statistical-thermodynamic model in order to compute the composition of the clathrate reservoir that forms as a result of the progressive entrapping of the liquid mixture. This study shows that clathrate formation strongly fractionates the molecules between the liquid and the solid phases. Depending on whether the structure I or structure II clathrate forms, the present model predicts that the liquid reservoirs would be mainly composed of either propane or ethane, r...

  20. Collection of liquid from below-ground location

    DOE Patents [OSTI]

    Phillips, S.J.; Alexander, R.G.

    1995-05-30T23:59:59.000Z

    A method is described for retrieving liquid from a below-ground collection area by permitting gravity flow of the liquid from the collection area to a first closed container; monitoring the level of the liquid in the closed container; and after the liquid reaches a given level in the first closed container, transferring the liquid to a second closed container disposed at a location above the first closed container, via a conduit, by introducing into the first closed container a gas which is substantially chemically inert with respect to the liquid, the gas being at a pressure sufficient to propel the liquid from the first closed container to the second closed container. 3 figs.

  1. Ternary liquid scintillator for optical fiber applications

    DOE Patents [OSTI]

    Franks, Larry A. (Santa Barbara, CA); Lutz, Stephen S. (Santa Barbara, CA)

    1982-01-01T23:59:59.000Z

    A multicomponent liquid scintillator solution for use as a radiation-to-light converter in conjunction with a fiber optic transmission system. The scintillator includes a quantity of 5-amino-9-diethylaminobenz (a) phenoxazonium nitrate (Nile Blue Nitrate) as a solute in a fluor solvent such as benzyl alcohol. The use of PPD as an additional solute is also disclosed. The system is controllable by addition of a suitable quenching agent, such as phenol.

  2. Hydrophilization of Liquid Surfaces by Plasma Treatment

    E-Print Network [OSTI]

    Victor Multanen; Gilad Chaniel; Roman Grynyov; Ron Yosef Loew; Naor Siany; Edward Bormashenko

    2014-09-01T23:59:59.000Z

    The impact of the cold radiofrequency air plasma on the surface properties of silicone oils (polydimethylsiloxane) was studied. Silicone oils of various molecular masses were markedly hydrophilized by the cold air plasma treatment. A pronounced decrease of the apparent water contact angles was observed after plasma treatment. A general theoretical approach to the calculation of apparent contact angles is proposed. The treated liquid surfaces demonstrated hydrophobic recovery. The characteristic time of the hydrophobic recovery grew with the molecular mass of the silicone oil.

  3. System and method for liquid silicon containment

    SciTech Connect (OSTI)

    Cliber, James A; Clark, Roger F; Stoddard, Nathan G; Von Dollen, Paul

    2014-06-03T23:59:59.000Z

    This invention relates to a system and a method for liquid silicon containment, such as during the casting of high purity silicon used in solar cells or solar modules. The containment apparatus includes a shielding ember adapted to prevent breaching molten silicon from contacting structural elements or cooling elements of a casting device, and a volume adapted to hold a quantity of breaching molten silicon with the volume formed by a bottom and one or more sides.

  4. System and method for liquid silicon containment

    DOE Patents [OSTI]

    Cliber, James A; Clark, Roger F; Stoddard, Nathan G; Von Dollen, Paul

    2013-05-28T23:59:59.000Z

    This invention relates to a system and a method for liquid silicon containment, such as during the casting of high purity silicon used in solar cells or solar modules. The containment apparatus includes a shielding member adapted to prevent breaching molten silicon from contacting structural elements or cooling elements of a casting device, and a volume adapted to hold a quantity of breaching molten silicon with the volume formed by a bottom and one or more sides.

  5. Dark Matter Search with Moderately Superheated Liquids

    E-Print Network [OSTI]

    L. A. Hamel; L. Lessard; V. Zacek; Bhaskar Sur

    1996-02-14T23:59:59.000Z

    We suggest the use of moderately superheated liquids in the form of superheated droplet detectors for a new type of neutralino search experiment. The advantage of this method for Dark Matter detection is, that the detector material is cheap, readily available and that it is easily possible to fabricate a large mass detector. Moreover the detector can be made "background blind", i.e. exclusively sensitive to nuclear recoils.

  6. Viscosity anomaly in core-softened liquids

    E-Print Network [OSTI]

    Yu. D. Fomin; V. N. Ryzhov

    2013-03-18T23:59:59.000Z

    The present article presents a molecular dynamics study of several anomalies of core-softened systems. It is well known that many core-softened liquids demonstrate diffusion anomaly. Usual intuition relates the diffusion coefficient to shear viscosity via Stockes-Einstein relation. However, it can break down at low temperature. In this respect it is important to see if viscosity also demonstrates anomalous behavior.

  7. Photorefractivity in liquid crystalline composite materials

    SciTech Connect (OSTI)

    Wiederrecht, G.P. [Argonne National Lab., IL (United States); Wasielewski, M.R. [Northwestern Univ., Evanston, IL (United States). Dept. of Chemistry

    1997-09-01T23:59:59.000Z

    We report recent improvements in the photorefractive of liquid crystalline thin film composites containing electron donor and acceptor molecules. The improvements primarily result from optimization of the exothermicity of the intermolecular charge transfer reaction and improvement of the diffusion characteristics of the photogenerated ions. Intramolecular charge transfer dopants produce greater photorefractivity and a 10-fold decrease in the concentration of absorbing chromophores. The mechanism for the generation of mobile ions is discussed.

  8. Noble Travails: Noble Liquid Dark Matter Detectors

    E-Print Network [OSTI]

    Golwala, Sunil

    , or water, 0.1x flux per 10 cm Cosmic Ray Muons generate high energy neutrons 50 MeV - 3 GeV which are toughGaitskell Noble Travails: Noble Liquid Dark Matter Detectors Rick Gaitskell Particle Astrophysics://particleastro.brown.edu/ http://gaitskell.brown.edu v1 #12;LUX Dark Matter Collaboration 2007 v01_7mm Dark Matter Theory

  9. The absorption of ultrasonic waves in liquids

    E-Print Network [OSTI]

    Hudson, Paul A

    1951-01-01T23:59:59.000Z

    in ?tope Of 6 Cas tO S aastana of 46 on, . oar chest runs were asks on each ltqnid to in euro that the data ?O~w rsp~oOucible, f ~ I'hs syparatno u~ in this work was stailar in tgye to that use'l at the K~X~t~ ?~iatIon tabor ster7i Ths liquid ", el...

  10. Effects of Nitrogen contamination in liquid Argon

    E-Print Network [OSTI]

    R. Acciarri; M. Antonello; B. Baibussinov; M. Baldo-Ceolin; P. Benetti; F. Calaprice; E. Calligarich; M. Cambiaghi; N. Canci; F. Carbonara; F. Cavanna; S. Centro; A. G. Cocco; F. Di Pompeo; G. Fiorillo; C. Galbiati; V. Gallo; L. Grandi; G. Meng; I. Modena; C. Montanari; O. Palamara; L. Pandola; F. Pietropaolo; G. L. Raselli; M. Roncadelli; M. Rossella; C. Rubbia; E. Segreto; A. M. Szelc; S. Ventura; C. Vignoli

    2008-04-08T23:59:59.000Z

    A dedicated test of the effects of Nitrogen contamination in liquid Argon has been performed at the INFN-Gran Sasso Laboratory (LNGS, Italy) within the WArP R&D program. A detector has been designed and assembled for this specific task and connected to a system for the injection of controlled amounts of gaseous Nitrogen into the liquid Argon. Purpose of the test is to detect the reduction of the Ar scintillation light emission as a function of the amount of the Nitrogen contaminant injected in the Argon volume. A wide concentration range, spanning from about 10^-1 ppm up to about 10^3 ppm, has been explored. Measurements have been done with electrons in the energy range of minimum ionizing particles (gamma-conversion from radioactive sources). Source spectra at different Nitrogen contaminations are analyzed, showing sensitive reduction of the scintillation yield at increasing concentrations. The rate constant of the light quenching process induced by Nitrogen in liquid Ar has been found to be k(N2)=0.11 micros^-1 ppm^-1. Direct PMT signals acquisition at high time resolution by fast Waveform recording allowed to extract with high precision the main characteristics of the scintillation light emission in pure and contaminated LAr. In particular, the decreasing behavior in lifetime and relative amplitude of the slow component is found to be appreciable from O(1 ppm) of Nitrogen concentrations.

  11. Liquid Vortex Shielding for Fusion Energy Applications

    SciTech Connect (OSTI)

    Bardet, Philippe M. [University of California, Berkeley (United States); Supiot, Boris F. [University of California, Berkeley (United States); Peterson, Per F. [University of California, Berkeley (United States); Savas, Oemer [University of California, Berkeley (United States)

    2005-05-15T23:59:59.000Z

    Swirling liquid vortices can be used in fusion chambers to protect their first walls and critical elements from the harmful conditions resulting from fusion reactions. The beam tube structures in heavy ion fusion (HIF) must be shielded from high energy particles, such as neutrons, x-rays and vaporized coolant, that will cause damage. Here an annular wall jet, or vortex tube, is proposed for shielding and is generated by injecting liquid tangent to the inner surface of the tube both azimuthally and axially. Its effectiveness is closely related to the vortex tube flow properties. 3-D particle image velocimetry (PIV) is being conducted to precisely characterize its turbulent structure. The concept of annular vortex flow can be extended to a larger scale to serve as a liquid blanket for other inertial fusion and even magnetic fusion systems. For this purpose a periodic arrangement of injection and suction holes around the chamber circumference are used, generating the layer. Because it is important to match the index of refraction of the fluid with the tube material for optical measurement like PIV, a low viscosity mineral oil was identified and used that can also be employed to do scaled experiments of molten salts at high temperature.

  12. Liquid uranium alloy-helium fission reactor

    DOE Patents [OSTI]

    Minkov, V.

    1984-06-13T23:59:59.000Z

    This invention describes a nuclear fission reactor which has a core vessel and at least one tandem heat exchanger vessel coupled therewith across upper and lower passages to define a closed flow loop. Nuclear fuel such as a uranium alloy in its liquid phase fills these vessels and flow passages. Solid control elements in the reactor core vessel are adapted to be adjusted relative to one another to control fission reaction of the liquid fuel therein. Moderator elements in the other vessel and flow passages preclude fission reaction therein. An inert gas such as helium is bubbled upwardly through the heat exchanger vessel operable to move the liquid fuel upwardly therein and unidirectionally around the closed loop and downwardly through the core vessel. This helium gas is further directed to heat conversion means outside of the reactor vessels to utilize the heat from the fission reaction to generate useful output. The nuclear fuel operates in the 1200 to 1800/sup 0/C range, and even higher to 2500/sup 0/C.

  13. Fermionic Luttinger liquids from a microscopic perspective

    E-Print Network [OSTI]

    Manuel Valiente; Lawrence G. Phillips; Nikolaj T. Zinner; Patrik Ohberg

    2015-05-13T23:59:59.000Z

    We consider interacting one-dimensional, spinless Fermi gases, whose low-energy properties are described by Luttinger liquid theory. We perform a systematic, in-depth analysis of the relation between the macroscopic, phenomenological parameters of Luttinger liquid effective field theory, and the microscopic interactions of the Fermi gas. In particular, we begin by explaining how to model effective interactions in one dimension, which we then apply to the main forward scattering channel -- the interbranch collisions -- common to these systems. We renormalise the corresponding interbranch phenomenological constants in favour of scattering phase shifts. Interestingly, our renormalisation procedure shows (i) how Luttinger's model arises in a completely natural way -- and not as a convenient approximation -- from Tomonaga's model, and (ii) the reasons behind the interbranch coupling constant remaining unrenormalised in Luttinger's model. We then consider the so-called intrabranch processes, whose phenomenological coupling constant is known to be fixed by charge conservation, but whose microscopic origin is not well understood. We show that, contrary to general belief and common sense, the intrabranch interactions appearing in Luttinger liquid theory do not correspond to an intrabranch scattering channel, nor an energy shift due to intrabranch interactions, in the microscopic theory. Instead, they are due to interbranch processes. We finally apply our results to a particular example of an exactly solvable model, namely the fermionic dual to the Lieb-Liniger model in the Tonks-Girardeau and super-Tonks-Girardeau regimes.

  14. Stretchable liquid crystal blue phase gels

    E-Print Network [OSTI]

    F. Castles; S. M. Morris; J. M. C. Hung; M. M. Qasim; A. D. Wright; S. Nosheen; S. S. Choi; B. I. Outram; S. J. Elston; C. Burgess; L. Hill; T. D. Wilkinson; H. J. Coles

    2014-01-26T23:59:59.000Z

    Liquid crystalline polymers are materials of considerable scientific interest and technological value to society [1-3]. An important subset of such materials exhibit rubber-like elasticity; these can combine the remarkable optical properties of liquid crystals with the favourable mechanical properties of rubber and, further, exhibit behaviour not seen in either type of material independently [2]. Many of their properties depend crucially on the particular mesophase employed. Stretchable liquid crystalline polymers have previously been demonstrated in the nematic, chiral nematic, and smectic mesophases [2,4]. Here were report the fabrication of a stretchable gel of blue phase I, which forms a self-assembled, three-dimensional photonic crystal that may have its optical properties manipulated by an applied strain and, further, remains electro-optically switchable under a moderate applied voltage. We find that, unlike its undistorted counterpart, a mechanically deformed blue phase exhibits a Pockels electro-optic effect, which sets out new theoretical challenges and new possibilities for low-voltage electro-optic devices.

  15. Phase-Changing Ionic Liquids: CO2 Capture with Ionic Liquids Involving Phase Change

    SciTech Connect (OSTI)

    None

    2010-07-01T23:59:59.000Z

    IMPACCT Project: Notre Dame is developing a new CO2 capture process that uses special ionic liquids (ILs) to remove CO2 from the gas exhaust of coal-fired power plants. ILs are salts that are normally liquid at room temperature, but Notre Dame has discovered a new class of ILs that are solid at room temperature and change to liquid when they bind to CO2. Upon heating, the CO2 is released for storage, and the ILs re-solidify and donate some of the heat generated in the process to facilitate further CO2 release. These new ILs can reduce the energy required to capture CO2 from the exhaust stream of a coal-fired power plant when compared to state-ofthe- art technology.

  16. How the Liquid-Liquid Transition Affects Hydrophobic Hydration in Deeply Supercooled Water

    E-Print Network [OSTI]

    Dietmar Paschek

    2005-03-21T23:59:59.000Z

    We determine the phase diagram of liquid supercooled water by extensive computer simulations using the TIP5P-E model [J. Chem. Phys. {\\bf 120}, 6085 (2004)]. We find that the transformation of water into a low density liquid in the supercooled range strongly enhances the solubility of hydrophobic particles. The transformation of water into a tetrahedrally structured liquid is accompanied by a minimum in the hydration entropy and enthalpy. The corresponding change in sign of the solvation heat capacity indicates a loss of one characteristic signature of hydrophobic hydration. The observed behavior is found to be qualitatively in accordance with the predictions of the information theory model of Garde et al. [Phys. Rev. Lett. {\\bf 77}, 4966 (1996)].

  17. Thermodynamic Model of Liquid-Liquid Phase Equilibrium in Solutions of Alkanethiol-Coated Nanoparticles

    E-Print Network [OSTI]

    Ezequiel R. Soule; Cristina E. Hoppe; Julio Borrajo; Roberto J. J. Williams

    2013-11-21T23:59:59.000Z

    A thermodynamic model for a mixture of alkanethiol-coated nanoparticles (NPs) and low molecular weight (non-polymeric) solvent is developed, and calculations of liquid-liquid phase equilibrium for different values of NP core radius, alkanethiol chain length, solvent molar volume and alkanethiol-solvent interaction parameter, are presented. The model takes into account the swelling of the organic coronas and the dispersion of particles with swollen coronas in the solvent. The energetic interaction between alkyl chains and solvent is considered, both within the corona and between the outer alkyl segments and free solvent. Swelling involves mixing of alkanethiol chains and solvent in the corona and stretching of the organic chains. Dispersion considers an entropic contribution based on Carnahan Starling equation of state and an enthalpic term calculated considering the surface contacts between alkyl segments placed in the external boundary of the corona and the molecules of free solvent. Two different kinds of phase equilibrium are found. One of them, observed at high values of the interaction parameter, is the typical liquid-liquid equilibrium for compact NPs in a poor solvent where a complete phase separation is observed when cooling (increasing the interaction parameter). The second liquid-liquid equilibrium is observed at low values of the interaction parameter, where swelling of coronas is favored. In this region two different phases co-exist, one more concentrated in NPs that exhibit relatively compact coronas and the other one more diluted in NPs with extended coronas. In diluted solutions of NPs the deswelling of the fully extended coronas takes place abruptly in a very small temperature range, leading to a solution of compact NPs. This critical transition might find practical applications similar to those found for the abrupt shrinkage of hydrogels at a critical temperature.

  18. Dye-Induced Enhancement of Optical Nonlinearity in Liquids and Liquid Crystals

    SciTech Connect (OSTI)

    Muenster, R.; Jarasch, M.; Zhuang, X.; Shen, Y. [Department of Physics, University of California, Berkeley, California 94720-7300 (United States)] [Department of Physics, University of California, Berkeley, California 94720-7300 (United States)

    1997-01-01T23:59:59.000Z

    Optical nonlinearity of liquid crystals (LC) in the isotropic phase can be enhanced by 1 order of magnitude by dissolving 0.1{percent} of anthraquinone dye in the LC. The enhancement decreases by {approximately}30{percent} when the LC transforms into the nematic phase. The same guest-host effect also exists in non-LC liquids. It can be explained by a model based on the change of guest-host interaction induced by optical excitations of the dye. {copyright} {ital 1996} {ital The American Physical Society}

  19. Structure and Depletion at Fluoro- and Hydro-carbon/Water Liquid/Liquid Interfaces

    E-Print Network [OSTI]

    Kaoru Kashimoto; Jaesung Yoon; Binyang Hou; Chiu-hao Chen; Binhua Lin; Makoto Aratono; Takanori Takiue; Mark L. Schlossman

    2008-07-18T23:59:59.000Z

    The results of x-ray reflectivity studies of two oil/water (liquid/liquid) interfaces are inconsistent with recent predictions of the presence of a vapor-like depletion region at hydrophobic/aqueous interfaces. One of the oils, perfluorohexane, is a fluorocarbon whose super-hydrophobic interface with water provides a stringent test for the presence of a depletion layer. The other oil, heptane, is a hydrocarbon and, therefore, is more relevant to the study of biomolecular hydrophobicity. These results are consistent with the sub-angstrom proximity of water to soft hydrophobic materials.

  20. Liquid-liquid equilibrium of cyclohexane-n-hexane-methanol mixtures; Effect of water content

    SciTech Connect (OSTI)

    Alessi, P.; Fermeglia, M.; Kikic, I. (Istituto di Chimica Applicata e Industriale, University of Trieste, via Valerio 2, I-34127 Trieste (IT))

    1989-04-01T23:59:59.000Z

    Experimental liquid-liquid equilibrium data for the ternary system cyclohexane-n-hexane-methanol and for the binary systems n-hexane-methanol and cyclohexane-methanol are presented over a temperature range from 284 to 298{Kappa} at pressure of 0.1 MPa. Attention is given to the effect of the purity of methanol as far as the water content is concerned. The data are correlated by means of excess Gibbs energy models (NRTL and UNIQUAC), and the binary interaction parameters are reported.

  1. Electromagnetic induction pump for pumping liquid metals and other conductive liquids

    DOE Patents [OSTI]

    Smither, Robert K. (Hinsdale, IL)

    1993-01-01T23:59:59.000Z

    An electromagnetic induction pump in which an electrically conductive liquid is made to flow by means of a force created by interaction of a permanent magnetic field and a DC current. The pump achieves high efficiency through combination of: powerful permanent magnet materials which provide a high strength field that is uniform and constant; steel tubing formed into a coil which is constructed to carry conducting liquids with minimal electrical resistance and heat; and application of a voltage to induce a DC current which continuously produces a force in the direction of the desired flow.

  2. Electromagnetic induction pump for pumping liquid metals and other conductive liquids

    DOE Patents [OSTI]

    Smither, R.K.

    1993-05-11T23:59:59.000Z

    An electromagnetic induction pump is described in which an electrically conductive liquid is made to flow by means of a force created by interaction of a permanent magnetic field and a DC current. The pump achieves high efficiency through combination of: powerful permanent magnet materials which provide a high strength field that is uniform and constant; steel tubing formed into a coil which is constructed to carry conducting liquids with minimal electrical resistance and heat; and application of a voltage to induce a DC current which continuously produces a force in the direction of the desired flow.

  3. Ultrasonic, Non-Invasive Classification/Discrimination of Liquid Explosives (LEs) and Threat Liquids from Non-Threat Liquids in Sealed Containers

    SciTech Connect (OSTI)

    Diaz, Aaron A.; Cinson, Anthony D.; Tucker, Brian J.; Samuel, Todd J.; Morales, Romarie

    2009-07-20T23:59:59.000Z

    Government agencies and homeland security organizations are searching for more effective approaches for dealing with the increasing demand for inspections involving potential threat liquids and hazardous chemicals, including liquid explosives (LEs). The quantity and variability of hand-held and cargo-sized containers being shipped worldwide drives the need for rapid and effective ways for conducting non-intrusive inspections of liquid-filled containers of a diverse range of types, shapes and sizes. Such inspections need to quickly classify/discriminate between liquids within containers and also ascertain the presence of unexpected objects within a container. The science base, methodology and prototype device for classification/discrimination between classes of liquids has been developed. The Pacific Northwest National Laboratory (PNNL) has developed a methodology and prototype device for classification/discrimination of a wide variety of liquids (including threat liquids and their precursors), providing noninvasive liquid classification/discrimination capabilities using a nondestructive ultrasonic measurement approach for inspecting sealed containers. The Container Screening Device (CSD) employs frequency-modulated (FM) chirp excitation and pulse-compression signal processing techniques to measure ultrasonic velocity and a relative attenuation value for liquids within a container, and is capable of determining other acoustic properties from through-transmission, contact measurements over a wide frequency range. Recent algorithm developments are beginning to address the issues of container wall variations and thickness. A description of the basic science, measurement approach and sources of variability in the measurement will be presented and laboratory measurements acquired from a suite of commercial products and precursor liquids used in the manufacturing of Homemade Explosives (HMEs) will be given.

  4. Instabilities during liquid migration into superheated hydrothermal systems

    SciTech Connect (OSTI)

    Fitzgerald, Shaun D.; Woods, Andrew W.

    1995-01-26T23:59:59.000Z

    Hydrothermal systems typically consist of hot permeable rock which contains either liquid or liquid and saturated steam within the voids. These systems vent fluids at the surface through hot springs, fumaroles, mud pools, steaming ground and geysers. They are simultaneously recharged as meteoric water percolates through the surrounding rock or through the active injection of water at various geothermal reservoirs. In a number of geothermal reservoirs from which significant amounts of hot fluid have been extracted and passed through turbines, superheated regions of vapor have developed. As liquid migrates through a superheated region of a hydrothermal system, some of the liquid vaporizes at a migrating liquid-vapor interface. Using simple physical arguments, and analogue laboratory experiments we show that, under the influence of gravity, the liquid-vapor interface may become unstable and break up into fingers.

  5. Non-electrolyte viscous liquid mixtures

    E-Print Network [OSTI]

    Wakefield, Dawn Lee

    1982-01-01T23:59:59.000Z

    . Equations Proposed for the Dependence of Viscosity of Liquid Mixtures on Chemical Composition at Constant Temperature, 36 TABLE III. TABLE IV. Compar1son of Errors in Determining Mixture Viscosit1es Using the Congruence-Viscos1ty Equat1on 86... states theory simplif1ed the more complex initial equations into the reasonably simple eq 3 lg. For ideal systems there is no "interaction viscosity, ny2 and the equation reduces to 2 + 2 nM Xl"1 X2n2 or nM = ZX 0 2 o o o (3. 20) R1ce compared...

  6. Algorithmic Cooling in Liquid State NMR

    E-Print Network [OSTI]

    Yosi Atia; Yuval Elias; Tal Mor; Yossi Weinstein

    2014-11-17T23:59:59.000Z

    Algorithmic cooling is a method that employs thermalization to increase the qubits' purification level, namely it reduces the qubit-system's entropy. We utilized gradient ascent pulse engineering (GRAPE), an optimal control algorithm, to implement algorithmic cooling in liquid state nuclear magnetic resonance. Various cooling algorithms were applied onto the three qubits of 13C2-trichloroethylene, cooling the system beyond Shannon's entropy bound in several different ways. For example, in one experiment a carbon qubit was cooled by a factor of 4.61. This work is a step towards potentially integrating tools of NMR quantum computing into in vivo magnetic resonance spectroscopy.

  7. DNA adsorption at liquid/solid interfaces

    E-Print Network [OSTI]

    Carine Douarche; Robert Cortès; Steven J. Roser; Jean-Louis Sikorav; Alan Braslau

    2008-09-26T23:59:59.000Z

    DNA adsorption on solid or liquid surfaces is a topic of broad fundamental and applied interest. Here we study by x-ray reflectivity the adsorption of monodisperse double-stranded DNA molecules a positively-charged surface, obtained through chemical grafting of a homogeneous organicmonomolecular layer of N-(2-aminoethyl) dodecanamide on an oxide-free monocrystalline Si(111) wafer. The adsorbed dsDNA is found to embed into the soft monolayer which is deformed in the process. The surface coverage is very high and this adsorbed layer is expected to display 2D nematic ordering.

  8. Commissioning of the ATLAS Liquid Argon Calorimeter

    E-Print Network [OSTI]

    S. Laplace

    2010-05-17T23:59:59.000Z

    The in-situ commissioning of the ATLAS liquid argon calorimeter is taking place since three years. During this period, it has been fully tested by means of frequent calibration runs, and the analysis of the large cosmic muon data samples and of the few beam splash events that occurred on September 10th, 2008. This has allowed to obtain a stable set of calibration constants for the first collisions, and to measure the in-situ calorimeter performances that were found to be at the expected level.

  9. Adsorptive Drying of Organic Liquids- An Update

    E-Print Network [OSTI]

    Joshi, S.; Humphrey, J. L.; Fair, J. R.

    (which is very heat sensitive and can poly merize in the presence of adsorbents) by freeze drying at -20 0 C and centrifuging the ice crystals. The water oontent was reduced from 700 ppm to 1~0 ppm. Pervaporation One of the recent advances... at The University of Texas at Austin will also be given. INTRODUCTION In the process industries it is often necessary to dry fluids before they can be processed further. For example, if a liquid is to be subjected to cryo genic conditions, its frost point must...

  10. High-pressure liquid chromatographic gradient mixer

    DOE Patents [OSTI]

    Daughton, C.G.; Sakaji, R.H.

    1982-09-08T23:59:59.000Z

    A gradient mixer effects the continuous mixing of any two miscible solvents without excessive decay or dispersion of the resultant isocratic effluent or of a linear or exponential gradient. The two solvents are fed under low or high pressure by means of two high performance liquid chromatographic pumps. The mixer comprises a series of ultra-low dead volume stainless steel tubes and low dead volume chambers. The two solvent streams impinge head-on at high fluxes. This initial nonhomogeneous mixture is then passed through a chamber packed with spirally-wound wires which cause turbulent mixing thereby homogenizing the mixture with minimum band-broadening.

  11. High pressure liquid chromatographic gradient mixer

    DOE Patents [OSTI]

    Daughton, Christian G. (San Pablo, CA); Sakaji, Richard H. (El Cerrito, CA)

    1985-01-01T23:59:59.000Z

    A gradient mixer which effects the continuous mixing of any two miscible solvents without excessive decay or dispersion of the resultant isocratic effluent or of a linear or exponential gradient. The two solvents are fed under low or high pressure by means of two high performance liquid chromatographic pumps. The mixer comprises a series of ultra-low dead volume stainless steel tubes and low dead volume chambers. The two solvent streams impinge head-on at high fluxes. This initial nonhomogeneous mixture is then passed through a chamber packed with spirally-wound wires which cause turbulent mixing thereby homogenizing the mixture with minimum "band-broadening".

  12. Durable electrooptic devices comprising ionic liquids

    SciTech Connect (OSTI)

    Agrawal, Anoop (Tucson, AZ); Cronin, John P. (Tucson, AZ); Tonazzi, Juan C. L. (Tucson, AZ); Warner, Benjamin P. (Los Alamos, NM); McCleskey, T. Mark (Los Alamos, NM); Burrell, Anthony K. (Los Alamos, NM)

    2005-11-01T23:59:59.000Z

    Electrolyte solutions for electrochromic devices such as rear view mirrors and displays with low leakage currents are prepared using inexpensive, low conductivity conductors. Preferred electrolytes include bifunctional redox dyes and molten salt solvents with enhanced stability toward ultraviolet radiation. The solvents include lithium or quaternary ammonium cations, and perfluorinated sulfonylimide anions selected from trifluoromethylsulfonate (CF3SO3-), bis(trifluoromethylsulfonyl)imide ((CF3SO2)2N-), bis(perfluoroethylsulfonyl)imide ((CF3CF2SO2)2N-) and tris(trifluoromethylsulfonyl)methide ((CF3SO2)3C-). Electroluminescent, electrochromic and photoelectrochromic devices with nanostructured electrodes include ionic liquids with bifunctional redox dyes.

  13. Ultrasonic characterization of solid liquid suspensions

    DOE Patents [OSTI]

    Panetta, Paul D.

    2010-06-22T23:59:59.000Z

    Using an ultrasonic field, properties of a solid liquid suspension such as through-transmission attenuation, backscattering, and diffuse field are measured. These properties are converted to quantities indicating the strength of different loss mechanisms (such as absorption, single scattering and multiple scattering) among particles in the suspension. Such separation of the loss mechanisms can allow for direct comparison of the attenuating effects of the mechanisms. These comparisons can also indicate a model most likely to accurately characterize the suspension and can aid in determination of properties such as particle size, concentration, and density of the suspension.

  14. Examination of Liquid Fluoride Salt Heat Transfer

    SciTech Connect (OSTI)

    Yoder Jr, Graydon L [ORNL] [ORNL

    2014-01-01T23:59:59.000Z

    The need for high efficiency power conversion and energy transport systems is increasing as world energy use continues to increase, petroleum supplies decrease, and global warming concerns become more prevalent. There are few heat transport fluids capable of operating above about 600oC that do not require operation at extremely high pressures. Liquid fluoride salts are an exception to that limitation. Fluoride salts have very high boiling points, can operate at high temperatures and low pressures and have very good heat transfer properties. They have been proposed as coolants for next generation fission reactor systems, as coolants for fusion reactor blankets, and as thermal storage media for solar power systems. In each case, these salts are used to either extract or deliver heat through heat exchange equipment, and in order to design this equipment, liquid salt heat transfer must be predicted. This paper discusses the heat transfer characteristics of liquid fluoride salts. Historically, heat transfer in fluoride salts has been assumed to be consistent with that of conventional fluids (air, water, etc.), and correlations used for predicting heat transfer performance of all fluoride salts have been the same or similar to those used for water conventional fluids an, water, etc). A review of existing liquid salt heat transfer data is presented, summarized, and evaluated on a consistent basis. Less than 10 experimental data sets have been found in the literature, with varying degrees of experimental detail and measured parameters provided. The data has been digitized and a limited database has been assembled and compared to existing heat transfer correlations. Results vary as well, with some data sets following traditional correlations; in others the comparisons are less conclusive. This is especially the case for less common salt/materials combinations, and suggests that additional heat transfer data may be needed when using specific salt eutectics in heat transfer equipment designs. All of the data discussed above were taken under forced convective conditions (both laminar and turbulent). Some recent data taken at ORNL under free convection conditions are also presented and results discussed. This data was taken using a simple crucible experiment with an instrumented nickel heater inserted in the salt to induce natural circulation within the crucible. The data was taken over a temperature range of 550oC to 650oC in FLiNaK salt. This data covers both laminar and turbulent natural convection conditions, and is compared to existing forms of natural circulation correlations.

  15. Air Liquide Hydrogen Energy | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnualProperty Edit withTianlinPapersWindeySanta2004) |Agawam,Ahmeek,Wisconsin: EnergyAir Liquide

  16. Liquid Propane Injection Applications | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(FactDepartment ofLetterEconomy and EmissionsDepartment of EnergyLiquid propane

  17. Natural Gas Plant Liquids Proved Reserves

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere IRaghuraji Agro IndustriesTownDells,1Stocks Nov-14 Dec-14 Jan-15LiquidBG 0 20Year Jan Feb2009FieldNatural

  18. Liquid Resources LLC | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are beingZealand Jump to: navigation, searchOf Kilauea Volcano,LakefrontLighthouse SolarI Jump to:Link toLiquid

  19. LiquidPiston Inc | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are beingZealand Jump to: navigation, searchOf Kilauea Volcano,LakefrontLighthouse SolarI Jump to:LinkLiquidPiston Inc

  20. Air Liquide Group | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnual Siteof Energy 2,AUDITCaliforniaWeifangwikiAgoura Hills,Oeste PaulistaLiquide Group Place:

  1. Fission and Nuclear Liquid-Gas Phase Transition

    E-Print Network [OSTI]

    E. A. Cherepanov; V. A. Karnaukhov

    2007-03-30T23:59:59.000Z

    The temperature dependence of the liquid-drop fission barrier is considered, the critical temperature for the liquid-gas phase transition in nuclear matter being a parameter. Experimental and calculated data on the fission probability are compared for highly excited $^{188}$Os. The calculations have been made in the framework of the statistical model. It is concluded that the critical temperature for the nuclear liquid--gas phase transition is higher than 16 MeV.

  2. Simulations of liquid ribidium expanded to the critical density

    SciTech Connect (OSTI)

    Ross, M; Yang, L H; Pilgrim, W

    2006-05-16T23:59:59.000Z

    Quantum molecular dynamic simulations were used to examine the change in atomic and electronic structure in liquid rubidium along its liquid-vapor coexistence curve. Starting from the liquid at the triple point, with increasing expansion we observe a continuous increase in the electron localization leading to ion clustering near the metal-nonmetal transition at about twice the critical density, in agreement with electrical measurements, and to the presence of dimers near and below the critical density.

  3. Superhydrophobic coated apparatus for liquid purification by evaporative condensation

    DOE Patents [OSTI]

    Simpson, John T; McNeany, Steve R; Dinsmore, Thomas V; Hunter, Scott R; Ivanov, Ilia N

    2014-03-11T23:59:59.000Z

    Disclosed are examples of apparatuses for evaporative purification of a contaminated liquid. In each example, there is a first vessel for storing the contaminated fluid. The first vessel includes a surface coated with a layer of superhydrophobic material and the surface is at least partially in contact with the contaminated liquid. The contaminants do not adhere to the surface as the purified liquid evaporates, thus simplifying maintenance of the apparatus.

  4. Energy Recovery By Direct Contact Gas-Liquid Heat Exchange

    E-Print Network [OSTI]

    Fair, J. R.; Bravo, J. L.

    ENERGY RECOVERY BY DIRECf CONTACf GAS-LIQUID HEAT EXCHANGE James R. Fair and Jose L. Bravo Separations Research Program The University o/Texas at Austin Austin, Texas ABSIRACf Energy from hot gas discharge streams can be recovered... by transfer directly to a coolant liquid in one of several available gas-liquid contacting devices. The design of the device is central to the theme of this paper, and experimental work has verified that the analogy between heat transfer and mass transfer...

  5. Shock compression of liquid helium to 56 GPa (560 kbar)

    SciTech Connect (OSTI)

    Nellis, W.J.; Holmes, N.C.; Mitchell, A.C.; Trainor, R.J.; Governo, G.K.; Ross, M.; Young, D.A.

    1984-09-24T23:59:59.000Z

    The first shock-compression experiments on liquid helium are reported. With a two-stage light-gas gun, liquid He at 4.3 K and 1 atm was shocked to 16 GPa and 12 000 K and double shocked to 56 GPa and 21 000 K. Liquid perturbation theory has been used to determine an effective interatomic potential from which the equation of state of He can be obtained over a wide range of densities and temperatures.

  6. aux interfaces liquide: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    (81 C), its relative safety (compared to liquids such as benzene and toluene of graphite under water and under cyclohexane will be discussed. From the results of this...

  7. Bio-Derived Liquids to Hydrogen Distributed Reforming Targets...

    Broader source: Energy.gov (indexed) [DOE]

    Development Manager, U.S. DOE Office of Energy Efficiency and Renewable Energy Hydrogen, Fuel Cells and Infrastructure Technologies Program Bio-Derived Liquids to Hydrogen...

  8. aqueous liquid waste: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Majda 2005-01-01 18 Momentum, Heat, and Neutral Mass Transport in Convective Atmospheric Pressure Plasma-Liquid Systems and Implications for Aqueous Targets CERN Preprints...

  9. ENVIRONMENTAL BIOTECHNOLOGY Effect of bulk liquid BOD concentration on activity

    E-Print Network [OSTI]

    Nerenberg, Robert

    BOD. FISH results indicated increasing abundance of heterotrophs with increasing bulk liquid BOD); however, competition of heterotrophs and nitrifiers in biofilm systems limits nitrification rates

  10. Measuring Diffusivity in Supercooled Liquid Nanoscale Films using...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    gas has been shown to be an effective probe of the diffusivity of supercooled liquid methanol in the experimentally challenging regime near the glass transition temperature. The...

  11. Soft ionization of thermally evaporated hypergolic ionic liquid aerosols

    E-Print Network [OSTI]

    Koh, Christine J.

    2013-01-01T23:59:59.000Z

    + ][Dca ? ]. Figure 2. Aerosol particle size distribution ofhypergolic ionic liquid aerosols Christine J. Koh † , Chen-ionization of evaporated IL aerosols Isolated ion pairs of a

  12. Notes 06. Liquid cavitation in fluid film bearings

    E-Print Network [OSTI]

    San Andres, Luis

    2009-01-01T23:59:59.000Z

    NOTES 6. CAVITATION IN LIQUID FILM BEARINGS. Dr. Luis San Andr?s ? 2009 1 NOTES 6. LIQUID CAVITATION IN FLUID FILM BEARINGS Lecture 6 describes the phenomenon of liquid cavitation in steadily loaded fluid film bearings and notes the most... ? Density at Pcav [kg/m 3 ] ? Fluid absolute viscosity [N.s/m 2 ] ? Journal angular speed (rad/s) Subscripts * Inception of the cavitation zone a Ambient value cav Cavitation NOTES 6. CAVITATION IN LIQUID FILM BEARINGS. Dr. Luis San Andr?s ? 2009...

  13. Lipid extraction from microalgae using a single ionic liquid

    DOE Patents [OSTI]

    Salvo, Roberto Di; Reich, Alton; Dykes, Jr., H. Waite H.; Teixeira, Rodrigo

    2013-05-28T23:59:59.000Z

    A one-step process for the lysis of microalgae cell walls and separation of the cellular lipids for use in biofuel production by utilizing a hydrophilic ionic liquid, 1-butyl-3-methylimidazolium. The hydrophilic ionic liquid both lyses the microalgae cell walls and forms two immiscible layers, one of which consists of the lipid contents of the lysed cells. After mixture of the hydrophilic ionic liquid with a suspension of microalgae cells, gravity causes a hydrophobic lipid phase to move to a top phase where it is removed from the mixture and purified. The hydrophilic ionic liquid is recycled to lyse new microalgae suspensions.

  14. Fabrication of fiber supported ionic liquids and methods of use

    DOE Patents [OSTI]

    Luebke, David R; Wickramanayake, Shan

    2013-02-26T23:59:59.000Z

    One or more embodiments relates to the production of a fabricated fiber having an asymmetric polymer network and having an immobilized liquid such as an ionic liquid within the pores of the polymer network. The process produces the fabricated fiber in a dry-wet spinning process using a homogenous dope solution, providing significant advantage over current fabrication methods for liquid-supporting polymers. The fabricated fibers may be effectively utilized for the separation of a chemical species from a mixture based on the selection of the polymer, the liquid, and the solvent utilized in the dope.

  15. Compositions and methods useful for ionic liquid treatment of biomass

    DOE Patents [OSTI]

    Dibble, Dean C.; Cheng, Aurelia; George, Anthe

    2014-07-29T23:59:59.000Z

    The present invention provides for novel compositions and methods for recycling or recovering ionic liquid used in IL pretreated cellulose and/or lignocellulosic biomass (LBM).

  16. Methods of making composite optical devices employing polymer liquid crystal

    DOE Patents [OSTI]

    Jacobs, S.D.; Marshall, K.L.; Cerqua, K.A.

    1991-10-08T23:59:59.000Z

    Composite optical devices are disclosed using polymer liquid crystal materials both as optical and adhesive elements. The devices are made by assembling a heated polymer liquid crystal compound, while in a low viscosity form between optically transparent substrates. The molecules of the polymer are oriented, while in the liquid crystalline state and while above the glass transition temperature (T[sub g]) of the polymer, to provide the desired optical effects, such as polarization, and selective reflection. The liquid crystal polymer cements the substrates together to form an assembly providing the composite optical device. 7 figures.

  17. Tokamak with liquid metal for inducing toroidal electrical field

    DOE Patents [OSTI]

    Ohkawa, Tihiro (La Jolla, CA)

    1981-01-01T23:59:59.000Z

    A tokamak apparatus includes a vessel for defining a reservoir and confining liquid therein. A toroidal liner disposed within said vessel defines a toroidal space within the liner confines gas therein. Liquid metal fills the reservoir outside the liner. A magnetic field is established in the liquid metal to develop magnetic flux linking the toroidal space. The gas is ionized. The liquid metal and the toroidal space are moved relative to one another transversely of the space to generate electric current in the ionized gas in the toroidal space about its major axis and thereby heat plasma developed in the toroidal space.

  18. Controlled Rapid Pressurization Using Liquid Propellants for EGS Well Stimulation

    Broader source: Energy.gov [DOE]

    Project objective: Investigate the use of non-toxic? or negligible environmental impact liquid propellants for the stimulation of geothermal fields.

  19. Bio-Derived Liquids to Hydrogen Distributed Reforming Working...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Working Group (BILIWG), Hydrogen Separation and Purification Working Group (PURIWG) & Hydrogen Production Technical Team Bio-Derived Liquids to Hydrogen Distributed Reforming...

  20. Existence of solutions to boundary value problems for smectic liquid ...

    E-Print Network [OSTI]

    2009-05-25T23:59:59.000Z

    Existence of solutions to boundary value problems for smectic liquid crys- tals. Abstract. We investigate variational problems for an energy developed by the.

  1. Enabling Small-Scale Biomass Gasification for Liquid Fuel Production...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Technologies II: Bio-Oils, Sugar Intermediates, Precursors, Distributed Models, and Refinery Co-Processing Enabling Small-Scale Biomass Gasification for Liquid Fuel Production...

  2. Ionic Liquids as Novel Engine Lubricants or Lubricant Additives...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    test results showed that compared with fully-formulated engine oils, selected low-viscosity ionic liquids, used as neat lubricants or basestock, produced significantly lower...

  3. Methods of making composite optical devices employing polymer liquid crystal

    DOE Patents [OSTI]

    Jacobs, Stephen D. (Pittsford, NY); Marshall, Kenneth L. (Henrietta, NY); Cerqua, Kathleen A. (Fairport, NY)

    1991-01-01T23:59:59.000Z

    Composite optical devices using polymer liquid crystal materials both as optical and adhesive elements. The devices are made by assembling a heated polymer liquid crystal compound, while in a low viscosity form between optically transparent substrates. The molecules of the polymer are oriented, while in the liquid crystalline state and while above the glass transition temperature (T.sub.g) of the polymer, to provide the desired optical effects, such as polarization, and selective reflection. The liquid crystal polymer cements the substrates together to form an assembly providing the composite optical device.

  4. Water-saving liquid-gas conditioning system

    DOE Patents [OSTI]

    Martin, Christopher; Zhuang, Ye

    2014-01-14T23:59:59.000Z

    A method for treating a process gas with a liquid comprises contacting a process gas with a hygroscopic working fluid in order to remove a constituent from the process gas. A system for treating a process gas with a liquid comprises a hygroscopic working fluid comprising a component adapted to absorb or react with a constituent of a process gas, and a liquid-gas contactor for contacting the working fluid and the process gas, wherein the constituent is removed from the process gas within the liquid-gas contactor.

  5. Optofluidic-Tunable Color Filters And Spectroscopy Based On Liquid...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Based On Liquid-Crystal Microflows. Abstract: The integration of color filters with microfluidics has attracted substantial attention in recent years, for on-chip absorption,...

  6. Sandia Energy - "Bionic" Liquids from Lignin: Joint BioEnergy...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Liquids from Lignin: Joint BioEnergy Institute Results Pave the Way for Closed-Loop Biofuel Refineries Home Renewable Energy Energy Transportation Energy Biofuels Facilities...

  7. Biomass and Natural Gas to Liquid Transportation Fuels

    Broader source: Energy.gov [DOE]

    Breakout Session 1: New Developments and Hot Topics Session 1-D: Natural Gas & Biomass to Liquids Josephine Elia, Graduate Student, Princeton University

  8. Bio-Derived Liquids to Hydrogen Distributed Reforming Targets

    Broader source: Energy.gov [DOE]

    Presentation by Arlene Anderson at the October 24, 2006 Bio-Derived Liquids to Hydrogen Distributed Reforming Working Group Kick-Off Meeting.

  9. Use of graphitized carbon beads for gas liquid chromatography

    DOE Patents [OSTI]

    Talmi, Yair (Oak Ridge, TN); Pollock, Charles B. (Oak Ridge, TN)

    1976-01-01T23:59:59.000Z

    Carbonized resin microspheroids are used as a column packing in gas-solid chromatography and as a support in gas-liquid chromatography.

  10. Electric field effects in liquid crystals with dielectric dispersion

    SciTech Connect (OSTI)

    Lavrentovich, Oleg D. [Kent State University

    2014-11-29T23:59:59.000Z

    The project is focused on the experimental and theoretical exploration of the coupling of an externally applied electric field and a nematic liquid crystal.

  11. New imaging tool directly measures liquid surfaces | EMSL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    directly measures liquid surfaces Released: May 30, 2013 Basic scientific insights of interest for energy storage, environmental cleanup The schematic of a vacuum compatible...

  12. Municipal Solid Waste (MSW) to Liquid Fuels Synthesis, Volume...

    Office of Environmental Management (EM)

    1: Availability of Feedstock and Technology Municipal Solid Waste (MSW) to Liquid Fuels Synthesis, Volume 1: Availability of Feedstock and Technology Municipal solid waste (MSW) is...

  13. Polymer-Ceramic Conversion of Liquid Polyaluminasilazanes for...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    were synthesized by simply reacting a liquid polyureasilazane with aluminum isopropoxide. The reaction was studied by FTIR and MS. The resultant...

  14. Liquid Fuels and Natural Gas in the Americas

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    materials) D 6751. Biofuels: Liquid fuels and blending components produced from biomass feedstocks, used primarily for transportation. Bitumen: A naturally occurring viscous...

  15. Liquid Hydrogen Production and Delivery from a Dedicated Wind...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    a Dedicated Wind Power Plant Liquid Hydrogen Production and Delivery from a Dedicated Wind Power Plant This May 2012 study assesses the costs and potential for remote renewable...

  16. A quantitative account of quantum effects in liquid water. |...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    report quantum statistical mechanical simulations of liquid water with the TTM2.1-F flexible, polarizable interaction potential for water. The potential is the first...

  17. Aprotic Heterocyclic Anion Triazolide Ionic Liquids - A New Class of Ionic Liquid Anion Accessed by the Huisgen Cycloaddition Reaction

    SciTech Connect (OSTI)

    Thompson, Robert L.; Damodaran, Krishnan; Luebke, David; Nulwala, Hunaid

    2013-06-01T23:59:59.000Z

    The triazole core is a highly versatile heterocyclic ring which can be accessed easily with the Cu(I)-catalyzed Huisgen cycloaddition reaction. Herein we present the preparation of ionic liquids that incorporate a 1,2,3-triazolide anion. These ionic liquids were prepared by a facile procedure utilizing a base-labile pivaloylmethyl group at the 1-position, which can act as precursors to 1H- 4-substituted 1,2,3-triazole. These triazoles were then subsequently converted into ionic liquids after deprotonation using an appropriate ionic liquid cation hydroxide. The densities and thermal decompositions of these ionic liquids were measured. These novel ionic liquids have potential applications in gas separations and in metal-free catalysis.

  18. Liquid chromatographic analysis of coal surface properties

    SciTech Connect (OSTI)

    Kwon, K.C.

    1991-01-01T23:59:59.000Z

    The main objectives of this proposed research are to refine further the inverse liquid chromatography technique for the study of surface properties of raw coals, treated coals and coal minerals in water, to evaluate relatively surface properties of raw coals, treated coals and coal minerals by inverse liquid chromatography, and to evaluate floatability of various treated coals in conjunction with surface properties of coals. Alcohols such as methanol, ethanol, isopropanol, isobutanol, tert-butanol, heptanol, 1-hexadecanol, 2-methyl-pentanol, 4-methyl-2-penthanol (methylisobutyl carbinol), n-octanol, s-octanol, and cyclohexanol as probe compounds are utilized to evaluate hydrophilicity of coals and coal minerals. N-alkanes such as hexane, heptane and octane, and stearic acid are employed as probe compounds to evaluate hydrophobicity of coals and coal minerals. Aromatic compounds such as benzene and toluene as probe compounds are used to examine aromaticity of coal surface. Aromatic acids such as o-cresol, m-cresol, p-cresol, phenol and B-naphthol are used to detect aromatic acidic sites of coal surface. Hydrophilicity, hydrophobicity and aromaticity of surfaces for either raw coals or treated coals in water are relatively determined by evaluating both equilibrium physical/chemical adsorption and dynamic adsorption of probe compounds on various raw coals and treated coals to compare affinities of coals for water.

  19. Future radioactive liquid waste streams study

    SciTech Connect (OSTI)

    Rey, A.S.

    1993-11-01T23:59:59.000Z

    This study provides design planning information for the Radioactive Liquid Waste Treatment Facility (RLWTF). Predictions of estimated quantities of Radioactive Liquid Waste (RLW) and radioactivity levels of RLW to be generated are provided. This information will help assure that the new treatment facility is designed with the capacity to treat generated RLW during the years of operation. The proposed startup date for the RLWTF is estimated to be between 2002 and 2005, and the life span of the facility is estimated to be 40 years. The policies and requirements driving the replacement of the current RLW treatment facility are reviewed. Historical and current status of RLW generation at Los Alamos National Laboratory are provided. Laboratory Managers were interviewed to obtain their insights into future RLW activities at Los Alamos that might affect the amount of RLW generated at the Lab. Interviews, trends, and investigation data are analyzed and used to create scenarios. These scenarios form the basis for the predictions of future RLW generation and the level of RLW treatment capacity which will be needed at LANL.

  20. Strong liquid-crystalline polymeric compositions

    DOE Patents [OSTI]

    Dowell, F.

    1993-12-07T23:59:59.000Z

    Strong liquid-crystalline polymeric (LCP) compositions of matter are described. LCP backbones are combined with liquid crystalline (LC) side chains in a manner which maximizes molecular ordering through interdigitation of the side chains, thereby yielding materials which are predicted to have superior mechanical properties over existing LCPs. The theoretical design of LCPs having such characteristics includes consideration of the spacing distance between side chains along the backbone, the need for rigid sections in the backbone and in the side chains, the degree of polymerization, the length of the side chains, the regularity of the spacing of the side chains along the backbone, the interdigitation of side chains in sub-molecular strips, the packing of the side chains on one or two sides of the backbone to which they are attached, the symmetry of the side chains, the points of attachment of the side chains to the backbone, the flexibility and size of the chemical group connecting each side chain to the backbone, the effect of semiflexible sections in the backbone and the side chains, and the choice of types of dipolar and/or hydrogen bonding forces in the backbones and the side chains for easy alignment. 27 figures.

  1. Liquid suspensions of reversible metal hydrides

    DOE Patents [OSTI]

    Reilly, J.J.; Grohse, E.W.; Winsche, W.E.

    1983-12-08T23:59:59.000Z

    The reversibility of the process M + x/2 H/sub 2/ ..-->.. MH/sub x/, where M is a metal hydride former that forms a hydride MH/sub x/ in the presence of H/sub 2/, generally used to store and recall H/sub 2/, is found to proceed under a liquid, thereby to reduce contamination, provide better temperature control and provide in situ mobility of the reactants. Thus, a slurry of particles of a metal hydride former with an inert solvent is subjected to temperature and pressure controlled atmosphere containing H/sub 2/, to store hydrogen (at high pressures) and to release (at low pressures) previously stored hydrogen. The direction of the flow of the H/sub 2/ through the liquid is dependent upon the H/sub 2/ pressure in the gas phase at a given temperature. When the former is above the equilibrium absorption pressure of the respective hydride the reaction proceeds to the right, i.e., the metal hydride is formed and hydrogen is stored in the solid particle. When the H/sub 2/ pressure in the gas phase is below the equilibrium dissociation pressure of the respective hydride the reaction proceeds to the left, the metal hydride is decomposed and hydrogen is released into the gas phase.

  2. Used powdex resin for liquid waste processing

    SciTech Connect (OSTI)

    Pearson, C.J.; Bramblett, J.W.

    1995-05-01T23:59:59.000Z

    Powdex resin has traditionally been used on the Secondary side for condensate polishing. The resins on these polishers are backwashed periodically based on chemical breakthrough or high differential pressure. Upon the backwash, the ion exchange capacity on the powdex resin is not completely exhausted. In the past, this partially used powdex resin was sluiced to a liner and treated as waste for disposal. In an effort to reduce radioactivity being released from segregated, high chemical concentration wastes, the idea of trying used powdex resin was initiated. In 1992, Duke Power Company began processing problem liquid waste streams with used Secondary powdex and subsequent decanting of the waste water for release. the results have shown significant reductions in the activity of this water. This paper will detail the history, method, and the results of using Secondary powdex for liquid radwaste processing. It will also describe the benefits, such as: (1) Processing waste streams not suitable for bead resin demineralizers. (2) Ability to process large volumes of waste water in a short period of time. (3) Recycling media thought to be useless. (4) > 80% Reduction in activity of water processed. (5) Overall curies reduction. (6) Improved bead demineralizer performance.

  3. Ultrasonic characterization of single drops of liquids

    DOE Patents [OSTI]

    Sinha, D.N.

    1998-04-14T23:59:59.000Z

    Ultrasonic characterization of single drops of liquids is disclosed. The present invention includes the use of two closely spaced transducers, or one transducer and a closely spaced reflector plate, to form an interferometer suitable for ultrasonic characterization of droplet-size and smaller samples without the need for a container. The droplet is held between the interferometer elements, whose distance apart may be adjusted, by surface tension. The surfaces of the interferometer elements may be readily cleansed by a stream of solvent followed by purified air when it is desired to change samples. A single drop of liquid is sufficient for high-quality measurement. Examples of samples which may be investigated using the apparatus and method of the present invention include biological specimens (tear drops; blood and other body fluid samples; samples from tumors, tissues, and organs; secretions from tissues and organs; snake and bee venom, etc.) for diagnostic evaluation, samples in forensic investigations, and detection of drugs in small quantities. 5 figs.

  4. Development of Practical Supported Ionic Liquid Membranes: A Systematic Approach

    SciTech Connect (OSTI)

    Luebke, D.R.; Ilconich, J.B.; Myers, C.R.; Pennline, H.W.

    2007-11-01T23:59:59.000Z

    Supported liquid membranes (SLMs) are a class of materials that allow the researcher to utilize the wealth of knowledge available on liquid properties to optimize membrane performance. These membranes also have the advantage of liquid phase diffusivities, which are higher than those observed in polymers and grant proportionally greater permeabilities. The primary shortcoming of the supported liquid membranes demonstrated in past research has been the lack of stability caused by volatilization of the transport liquid. Ionic liquids, which may possess high CO2 solubility relative to light gases such as H2, are excellent candidates for this type of membrane since they are stable at elevated temperatures and have negligible vapor pressure. A study has been conducted evaluating the use of a variety of ionic liquids in supported ionic liquid membranes for the capture of CO2 from streams containing H2. In a joint project, researchers at the University of Notre Dame synthesized and characterized ionic liquids, and researchers at the National Energy Technology Laboratory incorporated candidate ionic liquids into supports and evaluated membrane performance for the resulting materials. Several steps have been taken in the development of practical supported ionic liquid membranes. Proof-of-concept was established by showing that ionic liquids could be used as the transport media in SLMs. Results showed that ionic liquids are suitable media for gas transport, but the preferred polymeric supports were not stable at temperatures above 135oC. The use of cross-linked nylon66 supports was found to produce membranes mechanically stable at temperatures exceeding 300oC but CO2/H2 selectivity was poor. An ionic liquid whose selectivity does not decrease with increasing temperature was needed, and a functionalized ionic liquid that complexes with CO2 was used. An increase in CO2/H2 selectivity with increasing temperature over the range of 37 to 85oC was observed and the dominance of a facilitated transport mechanism established. The presentation will detail membrane development, the effect of increasing transmembrane pressure, and preliminary results dealing with other gas pairs and contaminants.

  5. Carbon Dioxide Separation with Supported Ionic Liquid Membranes

    SciTech Connect (OSTI)

    Luebke, D.R.; Ilconich, J.B.; Myers, C.R.; Pennline, H.W.

    2007-04-01T23:59:59.000Z

    Supported liquid membranes are a class of materials that allow the researcher to utilize the wealth of knowledge available on liquid properties as a direct guide in the development of a capture technology. These membranes also have the advantage of liquid phase diffusivities higher than those observed in polymeric membranes which grant proportionally greater permeabilities. The primary shortcoming of the supported liquid membranes demonstrated in past research has been the lack of stability caused by volatilization of the transport liquid. Ionic liquids, which possess high carbon dioxide solubility relative to light gases such as hydrogen, are an excellent candidate for this type of membrane since they have negligible vapor pressure and are not susceptible to evaporation. A study has been conducted evaluating the use of several ionic liquids, including 1-hexyl-3-methyl-imidazolium bis(trifuoromethylsulfonyl)imide, 1-butyl-3-methyl-imidazolium nitrate, and 1-ethyl-3-methyl-imidazolium sulfate in supported ionic liquid membranes for the capture of carbon dioxide from streams containing hydrogen. In a joint project, researchers at the University of Notre Dame lent expertise in ionic liquid synthesis and characterization, and researchers at the National Energy Technology Laboratory incorporated candidate ionic liquids into supports and evaluated the resulting materials for membrane performance. Initial results have been very promising with carbon dioxide permeabilities as high as 950 barrers and significant improvements in carbon dioxide/hydrogen selectivity over conventional polymers at 37C and at elevated temperatures. Results include a comparison of the performance of several ionic liquids and a number of supports as well as a discussion of innovative fabrication techniques currently under development.

  6. NOCHAR Polymers: An Aqueous and Organic Liquid Solidification Process for Cadarache LOR (Liquides Organiques Radioactifs) - 13195

    SciTech Connect (OSTI)

    Vaudey, Claire-Emilie; Renou, Sebastien; Porco, Julien [AREVA CL BU, STMI ZAC de Courcelle 1 route de la Noue 91196 Gif-sur-Yvette (France)] [AREVA CL BU, STMI ZAC de Courcelle 1 route de la Noue 91196 Gif-sur-Yvette (France); Kelley, Dennis [Pacific World Trade, Inc. Hillsdale Technical Center 6970 Hillsdale Court Indianapolis, Indiana 46250 (United States)] [Pacific World Trade, Inc. Hillsdale Technical Center 6970 Hillsdale Court Indianapolis, Indiana 46250 (United States); Cochaud, Chantal [CEA Cadarache, DSN/SGTD, 13108 St Paul Lez Durance Cedex (France)] [CEA Cadarache, DSN/SGTD, 13108 St Paul Lez Durance Cedex (France); Serrano, Roger [CEA Marcoule, DPAD, BP 17171, 30207 Bagnols sur Ceze Cedex (France)] [CEA Marcoule, DPAD, BP 17171, 30207 Bagnols sur Ceze Cedex (France)

    2013-07-01T23:59:59.000Z

    To handle the Very Low Level Waste (VLLW) and the Low Level Waste (LLW) in France, two options can be considered: the incineration at CENTRACO facility and the disposal facility on ANDRA sites. The waste acceptance in these radwaste routes is dependent upon the adequacy between the waste characteristics (physical chemistry and radiological) and the radwaste route specifications. If the waste characteristics are incompatible with the radwaste route specifications (presence of significant quantities of chlorine, fluorine, organic component etc or/and high activity limits), it is necessary to find an alternative solution that consists of a waste pre-treatment process. In the context of the problematic Cadarache LOR (Liquides Organiques Radioactifs) waste streams, two radioactive scintillation cocktails have to be treated. The first one is composed of organic liquids at 13.1 % (diphenyloxazol, mesitylene, TBP, xylene) and water at 86.9 %. The second one is composed of TBP at 8.6 % and water at 91.4 %. They contain chlorine, fluorine and sulphate and have got alpha/beta/gamma spectra with mass activities equal to some kBq.g{sup -1}. Therefore, tritium is present and creates the second problematic waste stream. As a consequence, in order for disposal acceptance at the ANDRA site, it is necessary to pre-treat the waste. The NOCHAR polymers as an aqueous and organic liquid solidification process seem to be an adequate solution. Indeed, these polymers constitute an important variety of products applied to the treatment of radioactive aqueous and organic liquids (solvent, oil, solvent/oil mixing etc) and sludge through a mechanical and chemical solidification process. For Cadarache LOR, N910 and N960 respectively dedicated to the organic and aqueous liquids solidification are considered. With the N910, the organic waste solidification occurs in two steps. As the organic liquid travels moves through the polymer strands, the strands swell and immobilise the liquid. Then as the polymer-organic cure, over time, the polymer continues to collapse on the organic to create a permanent bond. The N960 has the ability to absorb aqueous waste up to 100 times its own weight. It creates a strong mechanical bond which permanently traps the contamination imbedded in the aqueous liquids. As a consequence, these two polymers seem to be able to constitute a suitable solidification matrix for a final acceptance in storage on ANDRA sites. In order to validate the polymers as an acceptable aqueous and organic solidification process for Cadarache LOR, some solidification tests realized with N910 and N960, have been carried out for different Waste/Polymer ratios. The determination of the best Waste/Polymer ratio and of the optimal experimental parameters has been made through an exudation test. Indeed, the process prevents leaching and it results in the absence of residual free organic or aqueous liquid which is forbidden in storage by ANDRA specifications. With these test results, we generated scientific data which are fundamental to obtain an ANDRA agreement. As a conclusion, the aim of this study is to demonstrate that the solidification by polymers can constitute a pre-treatment solution for Cadarache LOR and more generally, for various organic and mixed organic/aqueous waste which can not be directly acceptable at CENTRACO facility or at ANDRA storage sites. This work is, therefore, a solid background to demonstrate the feasibility of the waste pre-treatment by solidification with polymers and to encourage the development of this process. (authors)

  7. Polymer-stabilized blue phase liquid crystals: a tutorial [Invited

    E-Print Network [OSTI]

    Wu, Shin-Tson

    Polymer-stabilized blue phase liquid crystals: a tutorial [Invited] Jin Yan and Shin-Tson Wu@mail.ucf.edu Abstract: Blue phase liquid crystals exhibit several attractive features, such as self-assembled three, and submillisecond response time. This tutorial gives step-by-step introduction on basic blue- phase materials

  8. High average power laser using a transverse flowing liquid host

    DOE Patents [OSTI]

    Ault, Earl R.; Comaskey, Brian J.; Kuklo, Thomas C.

    2003-07-29T23:59:59.000Z

    A laser includes an optical cavity. A diode laser pumping device is located within the optical cavity. An aprotic lasing liquid containing neodymium rare earth ions fills the optical cavity. A circulation system that provides a closed loop for circulating the aprotic lasing liquid into and out of the optical cavity includes a pump and a heat exchanger.

  9. MOTT INSULATORS, SPIN LIQUIDS AND QUANTUM DISORDERED SUPERCONDUCTIVITY

    E-Print Network [OSTI]

    COURSE 7 MOTT INSULATORS, SPIN LIQUIDS AND QUANTUM DISORDERED SUPERCONDUCTIVITY MATTHEW P.A. FISHER insulators and quantum magnetism 583 3.1 Spin models and quantum magnetism . . . . . . . . . . . . . . . . . . . . . . . . . . . . 637 #12;MOTT INSULATORS, SPIN LIQUIDS AND QUANTUM DISORDERED SUPERCONDUCTIVITY Matthew P.A. Fisher

  10. Head-on impact of liquid drops Robert D. Schroll

    E-Print Network [OSTI]

    Zhang, Wendy

    ) ]1/2 U0 impact speed 1 m/s C speed of sound 1500 m/s Us variation ! liquid ejected radially ! = radius / impact speed impact time-scale #12;Deformation Dominated by Inertia volume conservation ! pressure variation ! liquid ejected radially ! = radius / impact speed

  11. PHASE TRANSITION NEAR A LIQUID-GAS COEXISTENCE EQUILIBRIUM

    E-Print Network [OSTI]

    Wang, Xiao-Ping

    , are the states in which gas and liquid can stay in equilibrium. We denote c± = -p (±), the speed of sound) in general in a oscillatory manner with fre- quency determined in part by the speeds of sound in gas, the time needed for the sound wave to travel in liquid from the interface to the tube boundary

  12. Thick Liquid Blanket Concept APEX Interim Report November, 1999

    E-Print Network [OSTI]

    California at Los Angeles, University of

    the liquid impinges on the edge plasma or the corona surrounding the burning core plasma. The ability of the edge plasma to shield the core plasma from contamination by the evaporating liquid is the primary. The contamination in the core plasma from Li or F (and other elements) must be so low that its radiation does

  13. Structure and magnetic behavior of transition metal based ionic liquids

    SciTech Connect (OSTI)

    Del Sesto, Rico E [Los Alamos National Laboratory (LANL); Mccleskey, T [Los Alamos National Laboratory (LANL); Burrell, Anthony K [ORNL; Baker, Gary A [ORNL; Thompson, Joe D. [Los Alamos National Laboratory (LANL); Scott, Brian L. [Los Alamos National Laboratory (LANL); Wilkes, John S [United States Air Force Academy (USAFA), Colorado; Williams, Peg [United States Air Force Academy (USAFA), Colorado

    2008-01-01T23:59:59.000Z

    A series of ionic liquids containing different paramagnetic anions have been prepared and all show paramagnetic behavior with potential applications for magnetic and electrochromic switching as well as novel magnetic transport; also, the tetraalkylphosphonium-based ionic liquids reveal anomalous magnetic behavior.

  14. RESEARCH ARTICLE Particles for tracing turbulent liquid helium

    E-Print Network [OSTI]

    Lathrop, Daniel P.

    RESEARCH ARTICLE Particles for tracing turbulent liquid helium Gregory P. Bewley Æ K. R of local flow velocities in turbulent liquid helium, using tracer particles. We survey and evaluate, we note that cryogenic helium is attractive for experimental studies because its kinematic viscosity

  15. LIQUID MIXING STUDIES WITH AN INTEGRATED MIXER/VALVE

    E-Print Network [OSTI]

    Voldman, Joel

    181 LIQUID MIXING STUDIES WITH AN INTEGRATED MIXER/VALVE Joel Voldman* , Martha L. Gray, and testing of an integrated mixer/valve and a method for determining its mixing performance. The method of their mixing performance - the mixing time. We have designed and fabricated a microfabricated liquid mixer/valve

  16. Liquid Lithium Wall Experiments in CDX-U R. Majeski,

    E-Print Network [OSTI]

    California at Los Angeles, University of

    Liquid Lithium Wall Experiments in CDX-U R. Kaita, a R. Majeski, a S. Luckhardt, b R. Doerner, b M ABSTRACT The concept of a flowing lithium first wall for a fusion reactor may lead to a significant advance is intensely heated and well diagnosed, and an extensive liquid lithium plasma-facing surface will be used

  17. Viscosity, hard sphere diameter and interionic potential for liquid lead

    E-Print Network [OSTI]

    Boyer, Edmond

    L-347 Viscosity, hard sphere diameter and interionic potential for liquid lead G. Chaussemy The Macedo-Litovitz equation for a hard sphere liquid provides a satisfactory model for the viscosity of lead and molecular dynamics. The activation energy for viscosity (0.07 eV) is similar to the height of the interionic

  18. High power laser having a trivalent liquid host

    DOE Patents [OSTI]

    Ault, Earl R.

    2005-08-16T23:59:59.000Z

    A laser having a lasing chamber and a semiconductor pumping device with trivalent titanium ions dissolved in a liquid host within the lasing chamber. Since the host is a liquid, it can be removed from the optical cavity when it becomes heated avoiding the inevitable optical distortion and birefringence common to glass and crystal hosts.

  19. Global Assessments and Guidelines for Sustainable Liquid Biofuel

    E-Print Network [OSTI]

    Global Assessments and Guidelines for Sustainable Liquid Biofuel Production in Developing Countries Biofuel Production in Developing Countries FINAL REPORT A GEF Targeted Research Project Organized by Bernd for Sustainable Liquid Biofuels. A GEF Targeted Research Project. Heidelberg/Paris/Utrecht/Darmstadt, 29 February

  20. Magnetic propulsion of liquid Li in tokamaks 1

    E-Print Network [OSTI]

    Zakharov, Leonid E.

    Magnetic propulsion of liquid Li in tokamaks 1 Leonid E. Zakharov, Princeton University, Princeton of the torus. This effect of magnetic propulsion can be used for developing new approaches for protecting circumference. On the other hand, when the liquid lithium is held in a closed volume, magnetic propulsion

  1. Polarization controllable Fresnel lens using dye-doped liquid crystals

    E-Print Network [OSTI]

    Wu, Shin-Tson

    Polarization controllable Fresnel lens using dye- doped liquid crystals Tsung-Hsien Lin,1,2 Yuhua controllable Fresnel zone plate lens is demonstrated using a photo-induced alignment of the dye-doped liquid. X. Ren, S. Liu, and X. Zhang, "Fabrication of off-axis holographic Fresnel lens used as multiplexer

  2. Switchable Fresnel lens using polymer-stabilized liquid crystals

    E-Print Network [OSTI]

    Wu, Shin-Tson

    Switchable Fresnel lens using polymer-stabilized liquid crystals Yun-Hsing Fan, Hongwen Ren@mail.ucf.edu http:/lcd.creol.ucf.edu Abstract: A switchable Fresnel zone plate lens is demonstrated using a polymer controllable liquid crystal Fresnel lens," Proc. SPIE 1168, 352-357 (1989). 2. J. S. Patel and K. Rastani

  3. OIL DROPLET MANIPULATION USING LIQUID DIELECTROPHORESIS ON ELECTRET WITH SUPERLYOPHOBIC

    E-Print Network [OSTI]

    Kasagi, Nobuhide

    OIL DROPLET MANIPULATION USING LIQUID DIELECTROPHORESIS ON ELECTRET WITH SUPERLYOPHOBIC SURFACES flow friction for water and oil. Charge stability of electret in liquid is much improved with new hysteresis of SLS for oil droplets are experimentally demonstrated, indicating low motion resistance

  4. Sample Lesson Plan Flammable and Combustible Liquids 1 Lesson Plan

    E-Print Network [OSTI]

    Homes, Christopher C.

    . Explain at least 2 ways to avoid explosion or fire from flammable or combustible liquids. Possible 2000 F. There are two primary hazards associated with flammable and combustible liquids: explosion and fire. In order to prevent these hazards, this standard addresses the primary concern of design

  5. Irrigation of Liquid Manures with Solid Set Systems

    E-Print Network [OSTI]

    Kaye, Jason P.

    Irrigation of Liquid Manures with Solid Set Systems Albert R. Jarrett, Professor, Agricultural Extension Solid Set Irrigation System Solid set irrigation is a system of irrigation sprinklers and piping moved from one location to another). Solid set irrigation systems are rarely used to apply liquid manure

  6. Thin liquid lithium targets for high power density

    E-Print Network [OSTI]

    McDonald, Kirk

    High charge state High velocity flow ~60 m/s High heat capacity of Li Absorbs power depositedThin liquid lithium targets for high power density applications: heavy ion beam strippers and beta Hilton Malmö City #12;Outline Liquid Lithium Stripper idea for FRIB Brief theory of film stability

  7. Liquid Fuels and Natural Gas in the Americas

    Reports and Publications (EIA)

    2014-01-01T23:59:59.000Z

    The Energy Information Administration's (EIA) Liquid Fuels and Natural Gas in the Americas report, published today, is a Congressionally-requested study examining the energy trends and developments in the Americas over the past decade. The report focuses on liquid fuels and natural gas—particularly reserves and resources, production, consumption, trade, and investment—given their scale and significance to the region.

  8. Molecular dynamics of liquid benzene via femtosecond pulses laser excitation

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    1749 Molecular dynamics of liquid benzene via femtosecond pulses laser excitation J. Etchepare, G moléculaires. Abstract. 2014 We analyse the complex response of liquid benzene to the applied 45 fs FHWM new results obtained by the transient grating temporal behaviour analysis of benzene, a molecule

  9. Elementary excitations of liquid 4 He in aerogel

    E-Print Network [OSTI]

    Glyde, Henry R.

    Elementary excitations of liquid 4 He in aerogel O. Plantevin and B. Fa°k Commissariat a` l-roton excitations of liquid 4 He immersed in aerogel of 95% porosity have been measured using inelastic neutron.25 K. Aerogel grown with deuterated materials not exposed to air was used and measure- ments in bulk

  10. Heterogeneous cavitation in liquid helium 4 near a glass plate

    E-Print Network [OSTI]

    Caupin, Frédéric

    Heterogeneous cavitation in liquid helium 4 near a glass plate X. Chavanne, S. Balibar and F wave to study cavitation, i.e. the nucleation of bubbles, in liquid helium 4 near a clean glass plate and threshold pressures in the range 0 to -3 bar, significantly less negative than for homogeneous cavitation

  11. Liquids: Condensed, disordered, and sometimes complex David Chandler1

    E-Print Network [OSTI]

    Chandler, David

    and foams and domain structures of fluid membranes. They also play a significant role in forces affecting liquids approaching a glass transition. In this case, its source is correlated molecular dynamics. In particular, mol- ecules in glass-forming supercooled liquids are so tightly packed that no significant

  12. Graphene terahertz modulators by ionic liquid gating

    E-Print Network [OSTI]

    Wu, Yang; Qiu, Xuepeng; Liu, Jingbo; Deorani, Praveen; Banerjee, Karan; Son, Jaesung; Chen, Yuanfu; Chia, Elbert E M; Yang, Hyunsoo

    2015-01-01T23:59:59.000Z

    Graphene based THz modulators are promising due to the conical band structure and high carrier mobility of graphene. Here, we tune the Fermi level of graphene via electrical gating with the help of ionic liquid to control the THz transmittance. It is found that, in the THz range, both the absorbance and reflectance of the device increase proportionately to the available density of states due to intraband transitions. Compact, stable, and repeatable THz transmittance modulation up to 93% (or 99%) for a single (or stacked) device has been demonstrated in a broad frequency range from 0.1 to 2.5 THz, with an applied voltage of only 3 V at room temperature.

  13. Halogenation of Imidazolium Ionic Liquids. Thermodynamics Perspective

    E-Print Network [OSTI]

    Chaban, Vitaly V

    2015-01-01T23:59:59.000Z

    Imidazolium cations are promising for anion exchange membranes, and electrochemical applications and gas capture. They can be chemically modified in many ways including halogenation. Halogenation possibilities of the imidazole ring constitute a particular interest. This work investigates fluorination and chlorination reactions of all symmetrically non-equivalent sites of the imidazolium cation. Halogenation of all carbon atoms is thermodynamically permitted. Out of these, the most favorable site is the first methylene group of the alkyl chain. In turn, the least favorable site is carbon of the imidazole ring. Temperature dependence of enthalpy, entropy, and Gibbs free energy at 1 bar is discussed. The reported results provide an important guidance in functionalization of ionic liquids in search of task-specific compounds.

  14. Conversion of olefins to liquid motor fuels

    DOE Patents [OSTI]

    Rabo, Jule A. (Armonk, NY); Coughlin, Peter K. (Yorktown Heights, NY)

    1988-01-01T23:59:59.000Z

    Linear and/or branched claim C.sub.2 to C.sub.12 olefins are converted to hydrocarbon mixtures suitable for use as liquid motor fuels by contact with a catalyst capable of ensuring the production of desirable products with only a relatively minor amount of heavy products boiling beyond the diesel oil range. The catalyst having desirable stability during continuous production operations, comprises a steam stabilized zeolite Y catalyst of hydrophobic character, desirably in aluminum-extracted form. The olefins such as propylene, may be diluted with inerts, such as paraffins or with water, the latter serving to moderate the acidity of the catalyst, or to further moderate the activity of the aluminum-extracted catalyst, so as to increase the effective life of the catalyst.

  15. Durable electrooptic devices comprising ionic liquids

    SciTech Connect (OSTI)

    Burrell, Anthony K. (Los Alamos, NM); Agrawal, Anoop (Tucson, AZ); Cronin; John P. (Tucson, AZ); Tonazzi, Juan C. L. (Tucson, AZ); Warner, Benjamin P. (Los Alamos, NM); McCleskey, T. Mark (Los Alamos, NM)

    2009-12-15T23:59:59.000Z

    Electrolyte solutions for electrochromic devices such as rear view mirrors and displays with low leakage currents are prepared using inexpensive, low conductivity conductors. Preferred electrolytes include bifunctional redox dyes and molten salt solvents with enhanced stability toward ultraviolet radiation. The solvents include lithium or quaternary ammonium cations, and perfluorinated sulfonylimide anions selected from trifluoromethylsulfonate (CF.sub.3SO.sub.3.sup.-), bis(trifluoromethylsulfonyl)imide ((CF.sub.3SO.sub.2).sub.2N.sup.-), bis(perfluoroethylsulfonyl)imide ((CF.sub.3CF.sub.2SO.sub.2).sub.2N.sup.-) and tris(trifluoromethylsulfonyl)methide ((CF.sub.3SO.sub.2).sub.3C.sup.-). Electroluminescent, electrochromic and photoelectrochromic devices with nanostructured electrodes include ionic liquids with bifunctional redox dyes. Some of the electrolyte solutions color to red when devices employing the solutions are powered, leading to red or neutral electrooptic devices.

  16. Durable Electrooptic Devices Comprising Ionic Liquids

    DOE Patents [OSTI]

    Burrell, Anthony K. (Los Alamos, NM); Agrawal, Anoop (Tucson, AZ); Cronin, John P. (Tucson, AZ); Tonazzi, Juan C. L. (Tucson, AZ); Warner, Benjamin P. (Los Alamos, NM); McCleskey, T. Mark (Los Alamos, NM)

    2008-11-11T23:59:59.000Z

    Electrolyte solutions for electrochromic devices such as rear view mirrors and displays with low leakage currents are prepared using inexpensive, low conductivity conductors. Preferred electrolytes include bifunctional redox dyes and molten salt solvents with enhanced stability toward ultraviolet radiation. The solvents include lithium or quaternary ammonium cations, and perfluorinated sulfonylimide anions selected from trifluoromethylsulfonate (CF.sub.3SO.sub.3.sup.-), bis(trifluoromethylsulfonyl)imide ((CF.sub.3SO.sub.2).sub.2N.sup.-), bis(perfluoroethylsulfonyl)imide ((CF.sub.3CF.sub.2SO.sub.2).sub.2N.sup.-) and tris(trifluoromethylsulfonyl)methide ((CF.sub.3SO.sub.2).sub.3C.sup.-). Electroluminescent, electrochromic and photoelectrochromic devices with nanostructured electrodes include ionic liquids with bifunctional redox dyes. Some of the electrolyte solutions color to red when devices employing the solutions are powered, leading to red or neutral electrooptic devices.

  17. Durable electrooptic devices comprising ionic liquids

    SciTech Connect (OSTI)

    Warner, Benjamin P. (Los Alamos, NM); McCleskey, T. Mark (Los Alamos, NM); Burrell, Anthony K. (Los Alamos, NM)

    2006-10-10T23:59:59.000Z

    Electrolyte solutions for electrochromic devices such as rear view mirrors and displays with low leakage currents are prepared using inexpensive, low conductivity conductors. Preferred electrolytes include bifunctional redox dyes and molten salt solvents with enhanced stability toward ultraviolet radiation. The solvents include lithium or quaternary ammonium cations, and perfluorinated sulfonylimide anions selected from trifluoromethylsulfonate (CF.sub.3SO.sub.3.sup.-), bis(trifluoromethylsulfonyl)imide ((CF.sub.3SO.sub.2).sub.2N.sup.-), bis(perfluoroethylsulfonyl)imide ((CF.sub.3CF.sub.2SO.sub.2).sub.2N.sup.-) and tris(trifluoromethylsulfonyl)methide ((CF.sub.3SO.sub.2).sub.3C.sup.-). Electroluminescent, electrochromic and photoelectrochromic devices with nanostructured electrodes include ionic liquids with bifunctional redox dyes.

  18. Ternary liquid mixture viscosities and densities

    SciTech Connect (OSTI)

    Wei, I.C.; Rowley, R.L.

    1984-01-01T23:59:59.000Z

    Liquid mixture viscosities and densities have been measured at 298.15 K and ambient pressure for 20 ternary systems. Twelve ternary compositions, encompassing the entire composition range, have been chosen for each system in an effort to test a newly proposed predictive equation based on local compositions. Viscosities calculated by using the local composition model agreed with the experimental data within an average absolute deviation of 6.4%. No adjustable parameters were used and only binary interactions in the form of NRTL constants were input. The results of these studies indicate that the local composition model predictions are generally as good for multicomponent systems as they are for the corresponding binaries. 24 references, 3 tables.

  19. Biomass gasification for liquid fuel production

    SciTech Connect (OSTI)

    Najser, Jan, E-mail: jan.najser@vsb.cz, E-mail: vaclav.peer@vsb.cz; Peer, Václav, E-mail: jan.najser@vsb.cz, E-mail: vaclav.peer@vsb.cz [VSB - Technical university of Ostrava, Energy Research Center, 17. listopadu 15/2172, 708 33 Ostrava-Poruba (Czech Republic); Vantuch, Martin [University of Zilina, Faculty of Mechanical Engineering, Department of Power Engineering, Univerzitna 1, 010 26 Zilina (Slovakia)

    2014-08-06T23:59:59.000Z

    In our old fix-bed autothermal gasifier we tested wood chips and wood pellets. We make experiments for Czech company producing agro pellets - pellets made from agricultural waste and fastrenewable natural resources. We tested pellets from wheat and rice straw and hay. These materials can be very perspective, because they do?t compete with food production, they were formed in sufficient quantity and in the place of their treatment. New installation is composed of allothermal biomass fixed bed gasifier with conditioning and using produced syngas for Fischer - Tropsch synthesis. As a gasifying agent will be used steam. Gas purification will have two parts - separation of dust particles using a hot filter and dolomite reactor for decomposition of tars. In next steps, gas will be cooled, compressed and removed of sulphur and chlorine compounds and carbon dioxide. This syngas will be used for liquid fuel synthesis.

  20. Acetonitrile Drastically Boosts Conductivity of Ionic Liquids

    E-Print Network [OSTI]

    Chaban, Vitaly V; Kalugin, Oleg N; Prezhdo, Oleg V

    2012-01-01T23:59:59.000Z

    We apply a new methodology in the force field generation (PCCP 2011, 13, 7910) to study the binary mixtures of five imidazolium-based room-temperature ionic liquids (RTILs) with acetonitrile (ACN). The investigated RTILs are composed of tetrafluoroborate (BF4) anion and dialkylimidazolium cations, where one of the alkyl groups is methyl for all RTILs, and the other group is different for each RTILs, being ethyl (EMIM), butyl (BMIM), hexyl (HMIM), octyl (OMIM), and decyl (DMIM). Specific densities, radial distribution functions, ionic cluster distributions, heats of vaporization, diffusion constants, shear viscosities, ionic conductivities, and their correlations are discussed. Upon addition of ACN, the ionic conductivity of RTILs is found to increase by more than 50 times, that significantly exceeds an impact of most known solvents. Remarkably, the sharpest conductivity growth is found for the long-tailed imidazolium-based cations. This new fact motivates to revisit an application of these binary systems as a...

  1. In Situ Electron Energy Loss Spectroscopy in Liquids

    E-Print Network [OSTI]

    Holtz, Megan E; Gao, Jie; Abruña, Héctor D; Muller, David A

    2012-01-01T23:59:59.000Z

    In situ scanning transmission electron microscopy (STEM) through liquids is a promising approach for exploring biological and materials processes. However, options for in situ chemical identification are limited: X-ray analysis is precluded because the holder shadows the detector, and electron energy loss spectroscopy (EELS) is degraded by multiple scattering events in thick layers. Here, we explore the limits of EELS for studying chemical reactions in their native environments in real time and on the nanometer scale. The determination of the local electron density, optical gap and thickness of the liquid layer by valence EELS is demonstrated for liquids. By comparing theoretical and experimental plasmon energies, we find that liquids appear to follow the free-electron model that has been previously established for solids. Signals at energies below the optical gap and plasmon energy of the liquid provide a high signal-to-background ratio as demonstrated for LiFePO4 in aqueous solution. The potential for using...

  2. Reimagining liquid transportation fuels : sunshine to petrol.

    SciTech Connect (OSTI)

    Johnson, Terry Alan (Sandia National Laboratories, Livermore, CA); Hogan, Roy E., Jr.; McDaniel, Anthony H. (Sandia National Laboratories, Livermore, CA); Siegel, Nathan Phillip; Dedrick, Daniel E. (Sandia National Laboratories, Livermore, CA); Stechel, Ellen Beth; Diver, Richard B., Jr.; Miller, James Edward; Allendorf, Mark D. (Sandia National Laboratories, Livermore, CA); Ambrosini, Andrea; Coker, Eric Nicholas; Staiger, Chad Lynn; Chen, Ken Shuang; Ermanoski, Ivan; Kellog, Gary L.

    2012-01-01T23:59:59.000Z

    Two of the most daunting problems facing humankind in the twenty-first century are energy security and climate change. This report summarizes work accomplished towards addressing these problems through the execution of a Grand Challenge LDRD project (FY09-11). The vision of Sunshine to Petrol is captured in one deceptively simple chemical equation: Solar Energy + xCO{sub 2} + (x+1)H{sub 2}O {yields} C{sub x}H{sub 2x+2}(liquid fuel) + (1.5x+.5)O{sub 2} Practical implementation of this equation may seem far-fetched, since it effectively describes the use of solar energy to reverse combustion. However, it is also representative of the photosynthetic processes responsible for much of life on earth and, as such, summarizes the biomass approach to fuels production. It is our contention that an alternative approach, one that is not limited by efficiency of photosynthesis and more directly leads to a liquid fuel, is desirable. The development of a process that efficiently, cost effectively, and sustainably reenergizes thermodynamically spent feedstocks to create reactive fuel intermediates would be an unparalleled achievement and is the key challenge that must be surmounted to solve the intertwined problems of accelerating energy demand and climate change. We proposed that the direct thermochemical conversion of CO{sub 2} and H{sub 2}O to CO and H{sub 2}, which are the universal building blocks for synthetic fuels, serve as the basis for this revolutionary process. To realize this concept, we addressed complex chemical, materials science, and engineering problems associated with thermochemical heat engines and the crucial metal-oxide working-materials deployed therein. By project's end, we had demonstrated solar-driven conversion of CO{sub 2} to CO, a key energetic synthetic fuel intermediate, at 1.7% efficiency.

  3. LIQUID PROPANE GAS (LPG) STORAGE AREA BOILING LIQUID EXPANDING VAPOR EXPLOSION (BLEVE) ANALYSIS

    SciTech Connect (OSTI)

    PACE, M.E.

    2004-01-13T23:59:59.000Z

    The PHA and the FHAs for the SWOC MDSA (HNF-14741) identified multiple accident scenarios in which vehicles powered by flammable gases (e.g., propane), or combustible or flammable liquids (e.g., gasoline, LPG) are involved in accidents that result in an unconfined vapor cloud explosion (UVCE) or in a boiling liquid expanding vapor explosion (BLEVE), respectively. These accident scenarios are binned in the Bridge document as FIR-9 scenarios. They are postulated to occur in any of the MDSA facilities. The LPG storage area will be in the southeast corner of CWC that is relatively remote from store distaged MAR. The location is approximately 30 feet south of MO-289 and 250 feet east of 2401-W by CWC Gate 10 in a large staging area for unused pallets and equipment.

  4. Liquid-liquid equilibria of the ternary system water + acetic acid + 2-methyl-2-butanol

    SciTech Connect (OSTI)

    Fahim, M.A.; Al-Muhtaseb, S.A. [United Arab Emirates Univ., Al-Ain (United Arab Emirates). Dept. of Chemical and Petroleum Engineering] [United Arab Emirates Univ., Al-Ain (United Arab Emirates). Dept. of Chemical and Petroleum Engineering

    1996-11-01T23:59:59.000Z

    Liquid-liquid equilibria for the ternary system water + acetic acid + 2-methyl-2-butanol were measured over a temperature range of (288 to 323) K. The results were used to estimate the interaction parameters between each of the three compounds for the NRTL and UNIQUAC models and between each of the main groups of H{sub 2}O, CH{sub 2} (paraffinic CH{sub 2}), OH, and COOH for the UJNIFAC model as a function of temperature. The estimated interaction parameters were successfully used to predict the equilibrium compositions by the three models. The NRTL equation was the most accurate model in correlating the overall equilibrium compositions of the studied system. The UNIFAC model satisfactorily predicted the equilibrium compositions.

  5. Liquid-liquid equilibria of the ternary system water + acetic acid + 1-hexanol

    SciTech Connect (OSTI)

    Fahim, M.A. [Kuwait Univ., Safat (Kuwait). Dept. of Chemical Engineering] [Kuwait Univ., Safat (Kuwait). Dept. of Chemical Engineering; Al-Muhtaseb, S.A.; Al-Nashef, I.M. [U.A.E. Univ., Al-Ain (United Arab Emirates). Dept. of Chemical and Petroleum Engineering] [U.A.E. Univ., Al-Ain (United Arab Emirates). Dept. of Chemical and Petroleum Engineering

    1997-01-01T23:59:59.000Z

    The recovery of organic acids from dilute solutions resulting from fermentation processes is important and many solvents have been tried to improve such recovery. Liquid-liquid equilibria for the ternary system water + acetic acid + 1-hexanol were measured over a temperature range of (288 to 323) K. The results were used to estimate the interaction parameters between each of the three compounds for the NRTL and UNIQUAC models and between each of the main groups of H{sub 2}O, CH{sub 2} (paraffinic CH{sub 2}), OH, and COOH for the UNIFAC model as a function of temperature. The estimated interaction parameters were successfully used to predict the equilibrium compositions by the three models. The NRTL equation was the most accurate model in correlating the overall equilibrium compositions of the studied system. The UNIQUAC and UNIFAC models satisfactorily predicted the equilibrium compositions.

  6. Glass transition in biomolecules and the liquid-liquid critical point of water

    E-Print Network [OSTI]

    P. Kumar; Z. Yan; L. Xu; M. G. Mazza; S. V. Buldyrev; S. -H. Chen; S. Sastry; H. E. Stanley

    2006-08-28T23:59:59.000Z

    Using molecular dynamics simulations, we investigate the relation between the dynamic transitions of biomolecules (lysozyme and DNA) and the dynamic and thermodynamic properties of hydration water. We find that the dynamic transition of the macromolecules, sometimes called a ``protein glass transition'', occurs at the temperature of dynamic crossover in the diffusivity of hydration water, and also coincides with the maxima of the isobaric specific heat $C_P$ and the temperature derivative of the orientational order parameter. We relate these findings to the hypothesis of a liquid-liquid critical point in water. Our simulations are consistent with the possibility that the protein glass transition results from crossing the Widom line, which is defined as the locus of correlation length maxima emanating from the hypothesized second critical point of water.

  7. Ionic liquid ion source emitter arrays fabricated on bulk porous substrates for spacecraft propulsion

    E-Print Network [OSTI]

    Courtney, Daniel George

    2011-01-01T23:59:59.000Z

    Ionic Liquid Ion Sources (ILIS) are a subset of electrospray capable of producing bipolar beams of pure ions from ionic liquids. Ionic liquids are room temperature molten salts, characterized by negligible vapor pressures, ...

  8. Studies of ionic liquids in lithium-ion battery test systems

    E-Print Network [OSTI]

    Salminen, Justin; Prausnitz, John M.; Newman, John

    2006-01-01T23:59:59.000Z

    of ionic liquids in lithium-ion battery test systems J.battery point of view, it is essential that an ionic liquid – lithiumlead to battery short-out. The ionic-liquid / lithium-salt

  9. The use of ionic liquid ion sources (ILIS) in FIB applications

    E-Print Network [OSTI]

    Zorzos, Anthony Nicholas

    2009-01-01T23:59:59.000Z

    A new monoenergetic, high-brightness ion source can be constructed using an arrangement similar to liquid metal ion sources (LMIS) by substituting the liquid metal with an ionic liquid, or room temperature molten salt. Ion ...

  10. Probing Liquid Surfaces under Vacuum Using SEM and TOF-SIMS....

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Liquid Surfaces under Vacuum Using SEM and TOF-SIMS. Probing Liquid Surfaces under Vacuum Using SEM and TOF-SIMS. Abstract: Applying vacuum-based molecular probes of liquid...

  11. Effects of heat and mass transport on the hydrodynamics and stability of liquid desiccant films

    E-Print Network [OSTI]

    Pineda Vargas, Sergio Manuel

    2013-01-01T23:59:59.000Z

    5.8 Average liquid properties heat capacity, thermal5.9 Average liquid properties heat capacity, thermalFigure 5.8: Average liquid properties heat capacity, thermal

  12. Issues and design concepts for high-activity liquid packaging

    SciTech Connect (OSTI)

    Meinert, N.M. [Westinghouse Hanford Co., Richland, WA (United States); Riley, D. [Walla Walla College of Engineering, Walla Walla, WA (United States); Wells, A.H. [Nuclear Assurance Corp., Norcross, GA (United States)

    1994-02-01T23:59:59.000Z

    The tank waste pretreatment process involves the separation of low-level and high-level constituents. The liquid high-level defense production waste will be vitrified into thousands of glass logs at the US DOE sites and then transported to a high-level repository for final disposal. Pretreatment and vitrification technology will need to be developed and tested to assess cost-effectiveness. The appropriate pretreatment strategy for complex high-activity liquid will depend on proving a competent process. As technology development matures, actual liquid will be substituted for simulants, and pilot scale plants will replace laboratory scale process demonstrations. Development of this strategy depends on tank waste sample analyses and a high-activity liquid supply for process testing. However, high-activity liquid transportation beyond DOE site boundaries is limited to Type B quantities in volumes less than 50 mL; no licensed packaging exists for greater than 50 mL quantities. The following paper summarizes the need for a high-activity liquid packaging, and identifies the agencies effecting packaging design and transportation. The high-activity liquid packaging concept retrofits licensed spent fuel casks by replacing the spent fuel basket with a sturdy containment vessel appropriate for the chemical nature of the liquid. A Nuclear Packaging (Pacific Nuclear`s NuPat{trademark} 125-B) spent fuel cask was hypothetically retrofitted with a containment vessel filled with liquid source term, the radionuclide inventory contained in the liquid. The structural, thermal, dose rate, and criticality consequences of retrofitting the cask body were evaluated based on data in the 125-B Cask Safety Analysis Report for Packaging. In addition, future packaging development work is discussed.

  13. Creaming and breaking of liquid emulsions: a free boundary problem 1 / 48 Creaming and breaking of liquid

    E-Print Network [OSTI]

    Rosso, Fabio

    , as opposite to the other case called instead a water-in-oil emulsion. #12;Creaming and breaking of liquid emulsions: a free boundary problem 4 / 48 What is an emulsion? Everyday life examples (a) water-in-oil of the model 5 A priori estimates 6 Existence and uniqueness #12;Creaming and breaking of liquid emulsions

  14. Environ. Sci. Technol. 1994, 28, 1331-1340 Semlempirical Thermodynamic Modeling of Liquid-Liquid Phase Equilibria

    E-Print Network [OSTI]

    Peters, Catherine A.

    -Liquid Phase Equilibria: Coal Tar Dissolutionin Water-Miscible Solvents Catherine A. Peters'it and Richard 0 coaltar, solvent,and water using the nonrandom, two-liquid (NRTL) equation, a semi- empiricalexcessfreeenergyequation. Coaltar,a complex mixtureofpolycyclicaromatichydrocarbons(PAHs),was represented

  15. Liquid-liquid equilibria of water + methanol + 1-octanol and water + ethanol + 1-octanol at various temperatures

    SciTech Connect (OSTI)

    Arce, A.; Blanco, A.; Souza, P.; Vidal, I. (Univ. of Santiago de Compostela (Spain). Dept. of Chemical Engineering)

    1994-04-01T23:59:59.000Z

    This study is part of a wider program of research on the recovery of light alcohols from dilute aqueous solutions using high molecular weight solvents. The authors report liquid-liquid equilibrium data and binodal curves for the systems water + methanol + 1-octanol and water + ethanol + 1-octanol at 25, 35, and 45 C. The data were fitted to the NRTL and UNIQUAC equations.

  16. Calculation of Vapor-Liquid-Liquid Equilibria for the Fischer-Tropsch Reactor Effluents using Modified Peng-Robinson

    E-Print Network [OSTI]

    Skogestad, Sigurd

    Calculation of Vapor-Liquid-Liquid Equilibria for the Fischer- Tropsch Reactor Effluents using equilibrium in Fischer­Tropsch synthesis products. A group contribution method allowing the estimation the Fischer­Tropsch method is used to produce high-molecular-weight hydrocarbons from synthesis gas (syngas

  17. Many-body dissipative particle dynamics simulation of liquid/vapor and liquid/solid interactions

    SciTech Connect (OSTI)

    Arienti, Marco; Pan, Wenxiao; Li, Xiaoyi; Karniadakis, George E.

    2011-05-27T23:59:59.000Z

    The combination of short-range repulsive and long-range attractive forces in Many-body Dissipative Particle Dynamics (MDPD) is examined at a vapor/liquid and liquid/solid interface. Based on the radial distribution of the virial pressure in a drop at equilibrium, a systematic study is carried out to characterize the sensitivity of the surface tension coefficient with respect to the inter-particle interaction parameters. For the first time, this study highlights the approximately cubic dependence of the surface tension coefficient on the bulk density of the fluid. In capillary flow, MDPD solutions are shown to satisfy the condition on the wavelength of an axial disturbance leading to the pinch-off of a cylindrical liquid thread. Correctly, no pinch-off occurs below the cutoff wavelength. MDPD is augmented by a set of bell-shaped weight functions to model interaction with a solid wall. There, hydrophilic and hydrophobic behaviors, including the occurrence of slip in the latter, are reproduced using a modification in the weight function that avoids particle clustering. Finally, the dynamics of droplets entering an inverted Y-shaped fracture junction is correctly captured in simulations parameterized by the Bond number, proving the flexibility of MDPD in modeling interface-dominated flows.

  18. Solvatochromic characterization of the liquid phase in liquid-supercritical CO{sub 2} mixtures

    SciTech Connect (OSTI)

    Kelley, S.P.; Lemert, R.M. [Univ. of Toledo, OH (United States). Chemical Engineering Dept.] [Univ. of Toledo, OH (United States). Chemical Engineering Dept.

    1996-07-01T23:59:59.000Z

    The solvatochromic dye phenol blue (N,N-dimethylindoaniline) is used to characterize the solvent strength (polarity) of the saturated liquid phase in a series of solvent-carbon dioxide binary mixtures. Data were obtained at 35 and 55 C and at pressures up to {approximately}70 bar. Five solvents were investigated--acetone, cyclohexane, methanol, THF, and toluene. The polarity of the liquid phase decreases significantly with increasing pressure due to the increasing carbon dioxide content of this phase at equilibrium. For example, the polarity of acetone saturated with carbon dioxide at 35 C and {approximately}60 bar is equivalent to the polarity of pure cyclohexane at ambient pressure. The local environment about the dye is significantly richer in the polar liquid component than the bulk composition would indicate. The degree of enrichment reflects concentration effects at low pressure, and both concentration and pressure effects at high pressure where the mixtures are highly compressible. The NRTL model of Renon and Prausnitz is able to predict these local compositions with reasonable accuracy except at CO{sub 2}-rich conditions where compressibility effects are important.

  19. Solubilities and liquid phase nonidealities in coal liquids: Final report, July 30, 1984-July 30, 1987

    SciTech Connect (OSTI)

    McLaughlin, E.; Coon, J.E.

    1988-01-01T23:59:59.000Z

    The research effort was a three year study of the solubilities of polynuclear aromatic hydrocarbons (PAH's) in organic solvents and the vapor-liquid equilibria of some of these same systems. Solubilities of 102 systems were determined as functions of temperature from ambient temperature to the melting point of the solute. The systems are listed and results are presented. Solubility data were analyzed using four solution models (Regular Solution theory, Extended Regular Solution theory, Wilson's Equation, and UNIQUAC) and binary interaction parameters have been obtained for the liquid phase. Also included are analyses of 35 more systems that have been previously published, for the purpose of composition of the predicted activity coefficients. Vapor pressures were determined for five solvents versus temperature. Also determined were the vapor-liquid equilibria for a test system and for six new systems at three temperatures each. New systems are (tetralin-decalin, tetralin-biphenyl, decalin- biphenyl, tetralin-fluorene, tetralin-fluorene, tetralin- dibenzothiophene, and tetralin-dibenzofuran. Results have been analyzed using four common solution models (Wilson's, UNIQUAC, NRTL, and Van Laar) and the optimum binary parameters determined. We have compared the parameters (for Wilson's and UNIQUAC) for the two methods and discussed the pros and cons of each method as a source for these parameters. Some initial steps have been made towards utilizing statistical mechanical methods for these types of systems. 46 refs., 26 figs., 57 tabs.

  20. Strategies for Detecting Organic Liquids on Soils Using Mid-Infrared...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Strategies for Detecting Organic Liquids on Soils Using Mid-Infrared Reflection Spectroscopy . Strategies for Detecting Organic Liquids on Soils Using Mid-Infrared Reflection...

  1. Direct Observation of Colloidal Nanocrystals by Using Liquid Cell Transmission Electron Microscopy

    E-Print Network [OSTI]

    Park, Jungwon

    2012-01-01T23:59:59.000Z

    1 1.2 Preparation of Graphene Liquidcorrected TEM. 1.2 Preparation of Graphene Liquid Cells The3 Figure 1.2. Preparation of a graphene liquid

  2. Two-dimensional liquid chromatography system for online top-down...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    liquid chromatography system for online top-down mass spectrometry. Two-dimensional liquid chromatography system for online top-down mass spectrometry. Abstract: An online...

  3. Determining Transition State Geometries in Liquids Using 2D-IR

    E-Print Network [OSTI]

    Cahoon, James

    2008-01-01T23:59:59.000Z

    Material Determining transition state geometries in liquidsDetermining transition state geometries in liquids using 2D-are determined by the transition state connecting reactant

  4. Performance Evaluation for Modular, Scalable Liquid-Rack Cooling Systems in Data Centers

    E-Print Network [OSTI]

    Xu, TengFang

    2009-01-01T23:59:59.000Z

    Scalable Liquid-Rack Cooling Systems in Data Centers FinalFOR A MODULAR, SCALABLE LIQUID-RACK COOLING SYSTEM IN DATAINFORMATION ON THE CHARACTERISTICS OF COOLING SYSTEMS,

  5. Performance Evaluation for Modular, Scalable Liquid-Rack Cooling Systems in Data Centers

    E-Print Network [OSTI]

    Xu, TengFang

    2009-01-01T23:59:59.000Z

    Liquid-Rack Cooling Systems in Data Centers Final Report ToCOOLING SYSTEM IN DATA CENTERS ..Liquid-Rack Cooling System in Data Centers 1 Problem

  6. Toward new solid and liquid phase systems for the containment, transport and delivery of hydrogen

    Broader source: Energy.gov [DOE]

    Toward new solid and liquid phase systems for the containment, transport and delivery of hydrogen.Solid and liquid hydrogen carriers for use in hydrogen storage and delivery.

  7. Gas Transport and Control in Thick-Liquid Inertial Fusion Power Plants

    E-Print Network [OSTI]

    Debonnel, Christophe Sylvain

    2006-01-01T23:59:59.000Z

    c v is the solid or liquid heat capacity at constant volume,heat capacities and might be slightly retrograde. Retrograde liquid-

  8. Soft ionization of thermally evaporated hypergolic ionic liquid aerosols

    SciTech Connect (OSTI)

    University of California; ERC, Incorporated, Edwards Air Force Base; Air Force Research Laboratory, Edwards Air Force Base; National Synchrotron Radiation Research Center (NSRRC); Institute of Chemistry, Hebrew University; Koh, Christine J.; Liu, Chen-Lin; Harmon, Christopher W.; Strasser, Daniel; Golan, Amir; Kostko, Oleg; Chambreau, Steven D.; Vaghjiani, Ghanshyam L.; Leone, Stephen R.

    2011-07-19T23:59:59.000Z

    Isolated ion pairs of a conventional ionic liquid, 1-Ethyl-3-Methyl-Imidazolium Bis(trifluoromethylsulfonyl)imide ([Emim+][Tf2N?]), and a reactive hypergolic ionic liquid, 1-Butyl-3-Methyl-Imidazolium Dicyanamide ([Bmim+][Dca?]), are generated by vaporizing ionic liquid submicron aerosol particles for the first time; the vaporized species are investigated by dissociative ionization with tunable vacuum ultraviolet (VUV) light, exhibiting clear intact cations, Emim+ and Bmim+, presumably originating from intact ion pairs. Mass spectra of ion pair vapor from an effusive source of the hypergolic ionic liquid show substantial reactive decomposition due to the internal energy of the molecules emanating from the source. Photoionization efficiency curves in the near threshold ionization region of isolated ion pairs of [Emim+][Tf2N?]ionic liquid vapor are compared for an aerosol source and an effusive source, revealing changes in the appearance energy due to the amount of internal energy in the ion pairs. The aerosol source has a shift to higher threshold energy (~;;0.3 eV), attributed to reduced internal energy of the isolated ion pairs. The method of ionic liquid submicron aerosol particle vaporization, for reactive ionic liquids such as hypergolic species, is a convenient, thermally ?cooler? source of isolated intact ion pairs in the gas phase compared to effusive sources.

  9. Soft ionization of thermally evaporated hypergolic ionic liquid aerosols

    SciTech Connect (OSTI)

    University of California; ERC, Incorporated, Edwards Air Force Base; Air Force Research Laboratory, Edwards Air Force Base; National Synchrotron Radiation Research Center (NSRRC); Koh, Christine J.; Liu, Chen-Lin; Harmon, Christopher W.; Strasser, Daniel; Golan, Amir; Kostko, Oleg; Chambreau, Steven D.; L.Vaghjiani, Ghanshyam; Leone, Stephen R.

    2012-03-16T23:59:59.000Z

    Isolated ion pairs of a conventional ionic liquid, 1-Ethyl-3-Methyl-Imidazolium Bis(trifluoromethylsulfonyl)imide ([Emim+][Tf2N?]), and a reactive hypergolic ionic liquid, 1- Butyl-3-Methyl-Imidazolium Dicyanamide ([Bmim+][Dca?]), are generated by vaporizing ionic liquid submicron aerosol particles for the first time; the vaporized species are investigated by dissociative ionization with tunable vacuum ultraviolet (VUV) light, exhibiting clear intact cations, Emim+ and Bmim+, presumably originating from intact ion pairs. Mass spectra of ion pair vapor from an effusive source of the hypergolic ionic liquid show substantial reactive decomposition due to the internal energy of the molecules emanating from the source. Photoionization efficiency curves in the near threshold ionization region of isolated ion pairs of [Emim+][Tf2N?] ionic liquid vapor are compared for an aerosol source and an effusive source, revealing changes in the appearance energy due to the amount of internal energy in the ion pairs. The aerosol source has a shift to higher threshold energy (~;;0.3 eV), attributed to reduced internal energy of the isolated ion pairs. The method of ionic liquid submicron aerosol particle vaporization, for reactive ionic liquids such as hypergolic species, is a convenient, thermally ?cooler? source of isolated intact ion pairs in the gas phase compared to effusive sources.

  10. A High Temperature Liquid Plasma Model of the Sun

    E-Print Network [OSTI]

    Pierre-Marie Robitaille

    2004-10-04T23:59:59.000Z

    In this work, a liquid model of the Sun is presented wherein the entire solar mass is viewed as a high density/high energy plasma. This model challenges our current understanding of the densities associated with the internal layers of the Sun, advocating a relatively constant density, almost independent of radial position. The incompressible nature of liquids is advanced to prevent solar collapse from gravitational forces. The liquid plasma model of the Sun is a non-equilibrium approach, where nuclear reactions are free to occur throughout the solar mass. The primary means of addressing internal heat transfer are convection and conduction. As a result of the convective processes on the solar surface, the liquid model brings into question the established temperature of the solar photosphere by highlighting a violation of Kirchhoff's law of thermal emission. Along these lines, the model emphasizes that radiative emission is a surface phenomenon. Strong evidence is provided that the Sun is a high density/high energy liquid plasma. This evidence is based on our knowledge of Planckian thermal emission and condensed matter, including the existence of pressure ionization and liquid metallic hydrogen at high temperatures and pressures. The equations of magnetohydrodynamics are invoked as the proper vehicle for the understanding od stellar convection and structure. Prior to introducing the liquid plasma model, the historic and scientific justifications for the gaseous model of the Sun are reviewed and the gaseous equations of state are also discussed.

  11. X-rays at Solid-Liquid Surfaces

    SciTech Connect (OSTI)

    Dosch, Helmut (Max Planck Institute for Metals Research) [Max Planck Institute for Metals Research

    2007-05-02T23:59:59.000Z

    Solid-liquid interfaces play an important role in many areas of current and future technologies, and in our biosphere. They play a key role in the development of nanofluidics and nanotribology, which sensitively depend on our knowledge of the microscopic structures and phenomena at the solid-liquid interface. The detailed understanding of how a fluid meets a wall is also a theoretical challenge. In particular, the phenomena at repulsive walls are of interest, since they affect many different phenomena, such as water-repellent surfaces or the role of the hydrophobic interaction in protein folding. Recent x-ray reflectivity studies of various solid-liquid interfaces have disclosed rather intriguiing phenomena, which will be discussed in this lecture: premelting of ice in contact with silica; liquid Pb in contact with Si; water in contact with hydrophobic surfaces. These experiments, carried out with high-energy x-ray microbeams, reveal detailed insight into the liquid density profile closest to the wall. A detailed insight into atomistic phenomena at solid-liquid interfaces is also a prerequisite in the microscopic control of electrochemical reactions at interfaces. Recent x-ray studies show the enormous future potential of such non-destructive analytical tools for the in situ observation of (electro-)chemical surface reactions. This lecture will review recent x-ray experiments on solid-liquid interfaces.

  12. Liquid xenon detectors for particle physics and astrophysics

    SciTech Connect (OSTI)

    Aprile, E.; Doke, T. [Department of Physics, Columbia University, New York, New York 10027 (United States); Advanced Research Institute for Science and Engineering, Waseda University, Tokyo 169-8555 (Japan)

    2010-07-15T23:59:59.000Z

    This article reviews the progress made over the last 20 years in the development and applications of liquid xenon detectors in particle physics, astrophysics, and medical imaging experiments. A summary of the fundamental properties of liquid xenon as radiation detection medium, in light of the most current theoretical and experimental information is first provided. After an introduction of the different type of liquid xenon detectors, a review of past, current, and future experiments using liquid xenon to search for rare processes and to image radiation in space and in medicine is given. Each application is introduced with a survey of the underlying scientific motivation and experimental requirements before reviewing the basic characteristics and expected performance of each experiment. Within this decade it appears likely that large volume liquid xenon detectors operated in different modes will contribute to answering some of the most fundamental questions in particle physics, astrophysics, and cosmology, fulfilling the most demanding detection challenges. From detectors based solely on liquid xenon (LXe) scintillation, such as in the MEG experiment for the search of the rare ''{mu}{yields}e{gamma}'' decay, currently the largest liquid xenon detector in operation, and in the XMASS experiment for dark matter detection, to the class of time projection chambers which exploit both scintillation and ionization of LXe, such as in the XENON dark matter search experiment and in the Enriched Xenon Observatory for neutrinoless double beta decay, unrivaled performance and important contributions to physics in the next few years are anticipated.

  13. Enzymantic Conversion of Coal to Liquid Fuels

    SciTech Connect (OSTI)

    Richard Troiano

    2011-01-31T23:59:59.000Z

    The work in this project focused on the conversion of bituminous coal to liquid hydrocarbons. The major steps in this process include mechanical pretreatment, chemical pretreatment, and finally solubilization and conversion of coal to liquid hydrocarbons. Two different types of mechanical pretreatment were considered for the process: hammer mill grinding and jet mill grinding. After research and experimentation, it was decided to use jet mill grinding, which allows for coal to be ground down to particle sizes of 5 {mu}m or less. A Fluid Energy Model 0101 JET-O-MIZER-630 size reduction mill was purchased for this purpose. This machine was completed and final testing was performed on the machine at the Fluid Energy facilities in Telford, PA. The test results from the machine show that it can indeed perform to the required specifications and is able to grind coal down to a mean particle size that is ideal for experimentation. Solubilization and conversion experiments were performed on various pretreated coal samples using 3 different approaches: (1) enzymatic - using extracellular Laccase and Manganese Peroxidase (MnP), (2) chemical - using Ammonium Tartrate and Manganese Peroxidase, and (3) enzymatic - using the live organisms Phanerochaete chrysosporium. Spectral analysis was used to determine how effective each of these methods were in decomposing bituminous coal. After analysis of the results and other considerations, such as cost and environmental impacts, it was determined that the enzymatic approaches, as opposed to the chemical approaches using chelators, were more effective in decomposing coal. The results from the laccase/MnP experiments and Phanerochaete chrysosporium experiments are presented and compared in this final report. Spectra from both enzymatic methods show absorption peaks in the 240nm to 300nm region. These peaks correspond to aromatic intermediates formed when breaking down the coal structure. The peaks then decrease in absorbance over time, corresponding to the consumption of aromatic intermediates as they undergo ring cleavage. The results show that this process happens within 1 hour when using extracellular enzymes, but takes several days when using live organisms. In addition, live organisms require specific culture conditions, control of contaminants and fungicides in order to effectively produce extracellular enzymes that degrade coal. Therefore, when comparing the two enzymatic methods, results show that the process of using extracellular lignin degrading enzymes, such as laccase and manganese peroxidase, appears to be a more efficient method of decomposing bituminous coal.

  14. Process for blending coal with water immiscible liquid

    DOE Patents [OSTI]

    Heavin, Leonard J. (Olympia, WA); King, Edward E. (Gig Harbor, WA); Milliron, Dennis L. (Lacey, WA)

    1982-10-26T23:59:59.000Z

    A continuous process for blending coal with a water immiscible liquid produces a uniform, pumpable slurry. Pulverized raw feed coal and preferably a coal derived, water immiscible liquid are continuously fed to a blending zone (12 and 18) in which coal particles and liquid are intimately admixed and advanced in substantially plug flow to form a first slurry. The first slurry is withdrawn from the blending zone (12 and 18) and fed to a mixing zone (24) where it is mixed with a hot slurry to form the pumpable slurry. A portion of the pumpable slurry is continuously recycled to the blending zone (12 and 18) for mixing with the feed coal.

  15. Detection of free liquid in containers of solidified radioactive waste

    DOE Patents [OSTI]

    Greenhalgh, Wilbur O. (Richland, WA)

    1985-01-01T23:59:59.000Z

    A method of nondestructively detecting the presence of free liquid within a sealed enclosure containing solidified waste by measuring the levels of waste at two diametrically opposite locations while slowly tilting the enclosure toward one of said locations. When the measured level remains constant at the other location, the measured level at said one location is noted and any measured difference of levels indicates the presence of liquid on the surface of the solidified waste. The absence of liquid in the enclosure is verified when the measured levels at both locations are equal.

  16. Carbon Dioxide Separation with Supported Ionic Liquid Membranes

    SciTech Connect (OSTI)

    Luebke, D.R.; Ilconich, J.B.; Pennline, H.W.; Myers, C.R.

    2007-05-01T23:59:59.000Z

    A practical form of CO2 capture at water-gas shift conditions in the IGCC process could serve the dual function of producing a pure CO2 stream for sequestration and forcing the equilibrium-limited shift reaction to completion enriching the stream in H2. The shift temperatures, ranging from the low temperature shift condition of 260°C to the gasification condition of 900°C, limit capture options by diminishing associative interactions which favor removal of CO2 from the gas stream. Certain sorption interactions, such as carbonate formation, remain available but generally involve exceptionally high sorbent regeneration energies that contribute heavily to parasitic power losses. Carbon dioxide selective membranes need only establish an equilibrium between the gas phase and sorption states in order to transport CO2, giving them a potential energetic advantage over other technologies. Supported liquid membranes take advantage of high, liquid phase diffusivities and a solution diffusion mechanism similar to that observed in polymeric membranes to achieve superior permeabilities and selectivites. The primary shortcoming of the supported liquid membranes demonstrated in past research has been the lack of stability caused by volatilization of the transport liquid. Ionic liquids, which possess high CO2 solubility relative to light gases such as H2, are excellent candidates for this type of membrane since they have negligible vapor pressure and are not susceptible to evaporation. A study has been conducted evaluating the use of ionic liquids including 1-hexyl-3-methyl-imidazolium bis(trifuoromethylsulfonyl)imide in supported ionic liquid membranes for the capture of CO2 from streams containing H2. In a joint project, researchers at the University of Notre Dame synthesized and characterized ionic liquids, and researchers at the National Energy Technology Laboratory incorporated candidate ionic liquids into supports and evaluated the resulting materials for membrane performance. Improvements to the ionic liquid and support have allowed testing of these supported ionic liquid membranes at temperatures up to 300°C without loss of support mechanical stability or degradation of the ionic liquid. Substantial improvements in selectivity have also been observed at elevated temperature with the best membrane currently achieving optimum performance at 75°C.

  17. Liquid film thickness measurement by two-line TDLAS

    SciTech Connect (OSTI)

    Yang, Huinan [School of Energy and Power Engineering, University of Shanghai for Science and Technology, 200093, Shanghai, China and IVG, University of Duisburg-Essen, 47057, Duisburg (Germany); Chen, Jun; Cai, Xiaoshu [School of Energy and Power Engineering, University of Shanghai for Science and Technology, 200093, Shanghai (China); Greszik, Daniel; Dreier, Thomas; Schulz, Christof [IVG, University of Duisburg-Essen, 47057, Duisburg (Germany)

    2014-04-11T23:59:59.000Z

    A fiber-based two-line tunable diode-laser absorption sensor with two near-infrared (NIR) distributed-feedback (DFB) diode lasers at ?1.4 ?m was used for non-intrusive time-resolved liquid water film thickness measurement. When probing the liquid film at two different wavelengths with significantly different absorption cross-sections, the additional signal losses due to surface fowling, reflection and beam steering can be eliminated. In this work, the evaporation process of a liquid film on transparent quartz plate was tracked and large fluctuations of film thickness were found at the end of the evaporation.

  18. Decommissioning and Dismantling of Liquid Waste Storage and Liquid Waste Treatment Facility from Paldiski Nuclear Site, Estonia

    SciTech Connect (OSTI)

    Varvas, M. [AS ALARA, Leetse tee 21, Paldiski, 76806 (Estonia); Putnik, H. [Delegation of the European Commission to Russia, Kadashevskaja nab. 14/1 119017 Moscow (Russian Federation); Nirvin, B.; Pettersson, S. [SKB, Box 5864, Stockholm, SE-102 40 (Sweden); Johnsson, B. [Studsvik RadWaste, Nykoping, SE-611 82 (Sweden)

    2006-07-01T23:59:59.000Z

    The Paldiski Nuclear Facility in Estonia, with two nuclear reactors was owned by the Soviet Navy and was used for training the navy personnel to operate submarine nuclear reactors. After collapse of Soviet Union the Facility was shut down and handed over to the Estonian government in 1995. In co-operation with the Paldiski International Expert Reference Group (PIERG) decommission strategy was worked out and started to implement. Conditioning of solid and liquid operational waste and dismantling of contaminated installations and buildings were among the key issues of the Strategy. Most of the liquid waste volume, remained at the Facility, was processed in the frames of an Estonian-Finnish co-operation project using a mobile wastewater purification unit NURES (IVO International OY) and water was discharged prior to the site take-over. In 1999-2002 ca 120 m{sup 3} of semi-liquid tank sediments (a mixture of ion exchange resins, sand filters, evaporator and flocculation slurry), remained after treatment of liquid waste were solidified in steel containers and stored into interim storage. The project was carried out under the Swedish - Estonian co-operation program on radiation protection and nuclear safety. Contaminated installations in buildings, used for treatment and storage of liquid waste (Liquid Waste Treatment Facility and Liquid Waste Storage) were then dismantled and the buildings demolished in 2001-2004. (authors)

  19. Electrohydrodynamic instabilities in thin liquid trilayer films

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Roberts, Scott A. [Sandia National Lab., Albuquerque, NM (United States); Kumar, Satish [Univ. of Minnesota, Minneapolis, MN (United States)

    2010-09-12T23:59:59.000Z

    Experiments by Dickey et al. [Langmuir, 22, 4315 (2006)] and Leach et al. [Chaos, 15, 047506 (2005)] show that novel pillar shapes can be generated from electrohydrodynamic instabilities at the interfaces of thin polymer/polymer/air trilayer films. In this paper, we use linear stability analysis to investigate the effect of free charge and ac electric fields on the stability of trilayer systems. Our work is also motivated by our recent theoretical study [J. Fluid Mech., 631, 255 (2009)] which demonstrates how ac electric fields can be used to increase control over the pillar formation process in thin liquid bilayer films. For perfect dielectric films, the effect of an AC electric field can be understood by considering an equivalent DC field. Leaky dielectric films yield pillar configurations that are drastically different from perfect dielectric films, and AC fields can be used to control the location of free charge within the trilayer system. This can alter the pillar instability modes and generate smaller diameter pillars when conductivities are mismatched. The results presented here may be of interest for the creation of complex topographical patterns on polymer coatings and in microelectronics.

  20. Infrared curing simulations of liquid composites molding

    SciTech Connect (OSTI)

    Nakouzi, S.; Pancrace, J.; Schmidt, F. M.; Le Maoult, Y.; Berthet, F. [Universite de Toulouse (France); INSA, UPS, Mines Albi, ISAE, ICA - Institut Clement Ader, Campus Jarlard, F-81013 Albi cedex 09 (France); Ecole des Mines Albi, Campus Jarlard, F-81013 Albi (France)

    2011-05-04T23:59:59.000Z

    Infrared radiation is an effective energy source to cure thermosetting polymers. Its usage is expected to reduce curing time in comparison with thermal heating and mold thermally regulated. In addition, because of the polymerization mechanism and instant on-off control of this power, an improvement in the final properties of the material is also expected. In this paper, we studied the infrared interaction with carbon (or glass) fibers reinforced epoxy matrix, where Liquid resin infusion (LRI) is used to manufacture the composite. Temperature of the composite is a key parameter that affects its mechanical properties and is controlled by the infrared emitters and the exothermic heat released from the polymerization. Radiative heat flux is computed using the in-lab developed software RAYHEAT. Then, the heat flux (or absorbed energy for glass fibers) is exported to the finite element based program COMSOLMULTIPHYSICS where heat balance equation is solved. This equation is coupled with the exothermic heat released during the curing process in order to predict the composite temperature versus time and degree of cure. Numerical simulations will be performed on planar parts (sheet shape) as well as curvilinear shapes. Experimental validations of the infrared curing carbon (glass)-epoxy composite system are presented in this paper Sheet surface temperature distribution are measured thanks to infrared camera. Kinetic parameters were estimated from differential scanning calorimeter (DSC) experimental data.

  1. Parameter exploration of optically trapped liquid aerosols

    E-Print Network [OSTI]

    D. R. Burnham; P. J. Reece; D. McGloin

    2010-06-24T23:59:59.000Z

    When studying the motion of optically trapped particles on the $\\mu s$ time scale, in low viscous media such as air, inertia cannot be neglected. Resolution of unusual and interesting behaviour not seen in colloidal trapping experiments is possible. In attempt to explain the phenomena we use power spectral methods to perform a parameter study of the Brownian motion of optically trapped liquid aerosol droplets concentrated around the critically damped regime. We present evidence that the system is suitably described by a simple harmonic oscillator model which must include a description of Fax\\'{e}n's correction, but not necessarily frequency dependent hydrodynamic corrections to Stokes' law. We also provide results describing how the system behaves under several variables and discuss the difficulty in decoupling the parameters responsible for the observed behaviour. We show that due to the relatively low dynamic viscosity and high trap stiffness it is easy to transfer between over- and under-damped motion by experimentally altering either trap stiffness or damping. Our results suggest stable aerosol trapping may be achieved in under-damped conditions, but the onset of deleterious optical forces at high trapping powers prevents the probing of the upper stability limits due to Brownian motion.

  2. Colloidal liquids of yolk-shell particles

    E-Print Network [OSTI]

    L. E. Sanchez Diaz; E. C. Cortes-Morales; X. Li; Wei-Ren Chen; M. Medina-Noyola

    2014-07-23T23:59:59.000Z

    In this paper we develop statistical mechanical tools to describe the intermediate- and long-time collective- and self-diffusion properties of a liquid of strongly-interacting hollow spherical particles (shells), each bearing a smaller solid sphere (yolk) in its interior. To decouple two complex effects we assume that the hydrodynamic interactions can be accounted for through the effective short-time self-diffusion coefficients $D^0_s$ and $D^0_y$ that describe the short-time Brownian motion of the yolk and the shell particles, and develop a self-consistent generalized Langevin equation theory to describe the intermediate- and long-time effects of the direct shell-shell, yolk-shell and yolk-yolk interactions. In a concrete application, we consider the simplest yolk-shell model system involving purely repulsive hard-body interactions between all (shell and yolk) particles. Using a softened version of these interparticle potentials we perform Brownian dynamics simulations to determine the mean squared displacement of both types of particles, as well as the intermediate scattering function of the yolk-shell complex. We compare the theoretical and simulation results between them, and with the results for the same system in the absence of yolks. We find that the yolks, which have no effect on the shell-shell static structure, influences the dynamic properties in a predictable manner, fully captured by the theory.

  3. Acoustic detection of Immiscible Liquids in Sand

    SciTech Connect (OSTI)

    Geller, Jil T.; Kowalsky, Michael B.; Seifert, Patricia K.; Nihei, Kurt T.

    1999-03-01T23:59:59.000Z

    Laboratory cross-well P-wave transmission at 90 kHz was measured in a 61 cm diameter by 76 cm tall water-saturated sand pack, before and after introducing a non-aqueous phase organic liquid (NAPL) (n-dodecane). In one experiment NAPL was introduced to form a lens trapped by a low permeability layer; a second experiment considered NAPL residual trapped behind the front of flowing NAPL. The NAPL caused significant changes in the travel time and amplitude of first arrivals, as well as the generation of diffracted waves arriving after the direct wave. The spatial variations in NAPL saturation obtained from excavation at the end of the experiment correlated well with the observed variations in the P-wave amplitudes and travel times. NAPL residual saturation changes from NAPL flow channels of 3 to 4% were detectable and the 40 to 80% NAPL saturation in the NAPL lens was clearly visible at acoustic frequencies. The results of these experiments demonstrate that small NAPL saturations may be more easily detected with amplitude rather than travel time data, but that the relationships between the amplitude changes and NAPL saturation maybe more complex than those for velocity.

  4. Liquid cooled, linear focus solar cell receiver

    DOE Patents [OSTI]

    Kirpich, Aaron S. (Broomall, PA)

    1985-01-01T23:59:59.000Z

    Separate structures for electrical insulation and thermal conduction are established within a liquid cooled, linear focus solar cell receiver for use with parabolic or Fresnel optical concentrators. The receiver includes a V-shaped aluminum extrusion having a pair of outer faces each formed with a channel receiving a string of solar cells in thermal contact with the extrusion. Each cell string is attached to a continuous glass cover secured within the channel with spring clips to isolate the string from the external environment. Repair or replacement of solar cells is effected simply by detaching the spring clips to remove the cover/cell assembly without interrupting circulation of coolant fluid through the receiver. The lower surface of the channel in thermal contact with the cells of the string is anodized to establish a suitable standoff voltage capability between the cells and the extrusion. Primary electrical insulation is provided by a dielectric tape disposed between the coolant tube and extrusion. Adjacent solar cells are soldered to interconnect members designed to accommodate thermal expansion and mismatches. The coolant tube is clamped into the extrusion channel with a releasably attachable clamping strip to facilitate easy removal of the receiver from the coolant circuit.

  5. Electrohydrodynamic instabilities in thin liquid trilayer films

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Roberts, Scott A.; Kumar, Satish

    2010-01-01T23:59:59.000Z

    Experiments by Dickey and Leach show that novel pillar shapes can be generated from electrohydrodynamic instabilities at the interfaces of thin polymer/polymer/air trilayer films. In this paper, we use linear stability analysis to investigate the effect of free charge and ac electric fields on the stability of trilayer systems. Our work is also motivated by our recent theoretical study which demonstrates how ac electric fields can be used to increase control over the pillar formation process in thin liquid bilayer films. For perfect dielectric films, the effect of an AC electric field can be understood by considering an equivalent DCmore »field. Leaky dielectric films yield pillar configurations that are drastically different from perfect dielectric films, and AC fields can be used to control the location of free charge within the trilayer system. This can alter the pillar instability modes and generate smaller diameter pillars when conductivities are mismatched. The results presented here may be of interest for the creation of complex topographical patterns on polymer coatings and in microelectronics.« less

  6. Electron Liquids in Semiconductor Quantum Structures

    SciTech Connect (OSTI)

    Aron Pinczuk

    2009-05-25T23:59:59.000Z

    The groups led by Stormer and Pinczuk have focused this project on goals that seek the elucidation of novel many-particle effects that emerge in two-dimensional electron systems (2DES) as the result from fundamental quantum interactions. This experimental research is conducted under extreme conditions of temperature and magnetic field. From the materials point of view, the ultra-high mobility systems in GaAs/AlGaAs quantum structures continue to be at the forefront of this research. The newcomer materials are based on graphene, a single atomic layer of graphite. The graphene research is attracting enormous attention from many communities involved in condensed matter research. The investigated many-particle phenomena include the integer and fractional quantum Hall effect, composite fermions, and Dirac fermions, and a diverse group of electron solid and liquid crystal phases. The Stormer group performed magneto-transport experiments and far-infrared spectroscopy, while the Pinczuk group explores manifestations of such phases in optical spectra.

  7. Liquid cooled, linear focus solar cell receiver

    DOE Patents [OSTI]

    Kirpich, A.S.

    1983-12-08T23:59:59.000Z

    Separate structures for electrical insulation and thermal conduction are established within a liquid cooled, linear focus solar cell receiver for use with parabolic or Fresnel optical concentrators. The receiver includes a V-shaped aluminum extrusion having a pair of outer faces each formed with a channel receiving a string of solar cells in thermal contact with the extrusion. Each cell string is attached to a continuous glass cover secured within the channel with spring clips to isolate the string from the external environment. Repair or replacement of solar cells is effected simply by detaching the spring clips to remove the cover/cell assembly without interrupting circulation of coolant fluid through the receiver. The lower surface of the channel in thermal contact with the cells of the string is anodized to establish a suitable standoff voltage capability between the cells and the extrusion. Primary electrical insulation is provided by a dielectric tape disposed between the coolant tube and extrusion. Adjacent solar cells are soldered to interconnect members designed to accommodate thermal expansion and mismatches. The coolant tube is clamped into the extrusion channel with a releasably attachable clamping strip to facilitate easy removal of the receiver from the coolant circuit.

  8. NMR STUDIES OF LIQUID CRYSTALS AND MOLECULES DISSOLVED IN LIQUID CRYSTAL SOLVENTS

    SciTech Connect (OSTI)

    Drobny, G.P.

    1982-11-01T23:59:59.000Z

    This thesis describes several studies in which nuclear magnetic resonance (nmr) spectroscopy has been used to probe the structure, orientation and dynamics of liquid crystal mesogens and molecules dissolved in liquid crystalline phases. In addition, a modern high field nmr spectrometer is described which has been used to perform such nmr studies. Chapter 1 introduces the quantum mechanical formalisms used throughout this thesis and briefly reviews the fundamentals of nuclear spin physics and pulsed nmr spectroscopy. First the density operator is described and a specific form for the canonical ensemble is derived. Then Clebsch-Gordon coefficients, Wigner rotation matrices, and irreducible tensor operators are reviewed. An expression for the equilibrium (Curie) magnetization is obtained and the linear response of a spin system to a strong pulsed r.f. irradiation is described. Finally, the spin interaction Hamiltonians relevant to this work are reviewed together with their truncated forms. Chapter 2 is a deuterium magnetic resonance study of two 'nom' liquid crystals which possess several low temperature mesomorphic phases. Specifically, deuterium quadrupolar echo spectroscopy is used to determine the orientation of the liquid crystal molecules in smectic phases, the changes in molecular orientation and motion that occur at smectic-smectic phase transitions, and the order of the phase transitions. For both compounds, the phase sequence is determined to be isotropic, nematic, smectic A, smectic C, smectic B{sub A}, smectic B{sub C}, and crystalline. The structure of the smectic A phase is found to be consistent with the well-known model of a two dimensional liquid in which molecules are rapidly rotating about their long axes and oriented at right angles to the plane of the layers. Molecules in the smectic C phase are found to have their long axes tilted with respect to the layer normal, and the tilt angle is temperature dependent, increasing from zero at the smectic A - smectic C transition and reaching a maximum at 9{sup o} at the smectic C - smectic B{sub A} transition. This finding contradicts the results of X-ray diffraction studies which indicate that the tilt angle is 18{sup o} and temperature independent. The smectic B{sub A} - smectic B{sub C} phase transition is observed for the first time, and is found to be first order, a result that contradicts the prediction of a mean theory by McMillian. Chapter 3 is a multiple quantum nmr study of n-hexane oriented in a nematic liquid crystal solvent. The basic three pulse multiple quantum experiment is discussed which enables the observation of transitions for which |{Delta}m|>1, and then the technique of the separation of multiple quantum orders by phase incrementation in the multiple quantum evolution period is reviewed (TPPI). An explicit example of multiple quantum nmr is given by the calculation of the multiple quantum spectrum of an oriented methyl group.

  9. Modeling multiphase flow for high viscosity liquids: a study of vertical/inclined zero net liquid flow

    E-Print Network [OSTI]

    Rodriguez, Jose Ramon

    2001-01-01T23:59:59.000Z

    conducted with superficial gas velocities ranging trom approximately 0. 100 to 4. 500 m/s, liquid viscosity from 1 to 124 cps and inclination angle from 90 to 50'. These tests yielded ZNLF liquid holdup measurements in the range of 0. 800 to 0. 040. A... is increased from horizontal, which leads to a higher slippage and liquid holdup. 38 0 900 Hte 0 800 0. 700 0 600 0 500 0 400 0 300 0. 200 + 0 100 0 000 20 80 120 140 Vtseosttt, eps e0103 ~ 0207 40413 x0827 x 1240 ~ 1654 +2067 -2894 -3720 44547...

  10. Vapor-liquid equilibria of coal-derived liquids; 3: Binary systems with tetralin at 200 mmHg

    SciTech Connect (OSTI)

    Blanco, B.; Beltran, S.; Cabezas, J.L. (University Coll., Burgos (Spain). Dept. of Chemical Engineering); Coca, J. (Univ. of Oviedo (Spain). Dept. of Chemical Engineering)

    1994-01-01T23:59:59.000Z

    Isobaric vapor-liquid equilibrium data are reported for binary systems of tetralin with p-xylene, [gamma]-picoline, piperidine, and pyridine; all systems were measured at 26.66 kPa (200 mmHg) with a recirculation still. Liquid-phase activity coefficients were correlated using the Van Laar, Wilson, NRTL, and UNIQUAC equations. Vapor-phase nonidealities were found negligible under the experimental conditions of this work, and deviations of the liquid phase from the ideal behavior, as described by Raoult's law, were found to be slightly positive for all the systems.

  11. Liquid crystal devices especially for use in liquid crystal point diffraction interferometer systems

    DOE Patents [OSTI]

    Marshall, Kenneth L. (Rochester, NY)

    2009-02-17T23:59:59.000Z

    Liquid crystal point diffraction interferometer (LCPDI) systems that can provide real-time, phase-shifting interferograms that are useful in the characterization of static optical properties (wavefront aberrations, lensing, or wedge) in optical elements or dynamic, time-resolved events (temperature fluctuations and gradients, motion) in physical systems use improved LCPDI cells that employ a "structured" substrate or substrates in which the structural features are produced by thin film deposition or photo resist processing to provide a diffractive element that is an integral part of the cell substrate(s). The LC material used in the device may be doped with a "contrast-compensated" mixture of positive and negative dichroic dyes.

  12. Liquid membrane coated ion-exchange column solids

    DOE Patents [OSTI]

    Barkey, Dale P. (Berkeley, CA)

    1989-01-01T23:59:59.000Z

    This invention relates to a method for improving the performance of liquid embrane separations by coating a liquid membrane onto solid ion-exchange resin beads in a fixed bed. Ion-exchange beads fabricated from an ion-exchange resin are swelled with water and are coated with a liquid membrane material that forms a film over the beads. The beads constitute a fixed bed ion-exchange column. Fluid being treated that contains the desired ion to be trapped by the ion-exchange particle is passed through the column. A carrier molecule, contained in the liquid membrane ion-exchange material, is selected for the desired ion in the fluid. The carrier molecule forms a complex with the desired ion, transporting it through the membrane and thus separating it from the other ions. The solution is fed continuously until breakthrough occurs at which time the ion is recovered, and the bed is regenerated.

  13. Liquid membrane coated ion-exchange column solids

    DOE Patents [OSTI]

    Barkey, Dale P. (Berkeley, CA)

    1988-01-01T23:59:59.000Z

    This invention relates to a method for improving the performance of liquid membrane separations by coating a liquid membrane onto solid ion-exchange resin beads in a fixed bed. Ion-exchange beads fabricated from an ion-exchange resin are swelled with water and are coated with a liquid membrane material that forms a film over the beads. The beads constitute a fixed bed ion-exchange column. Fluid being treated that contains the desired ion to be trapped by the ion-exchange particle is passed through the column. A carrier molecule, contained in the liquid membrane ion-exchange material, is selective for the desired ion in the fluid. The carrier molecule forms a complex with the desired ion, transporting it through the membrane and thus separating it from the other ions. The solution is fed continuously until breakthrough occurs at which time the ion is recovered, and the bed is regenerated.

  14. Elasto-capillary thinning and breakup of model elastic liquids

    E-Print Network [OSTI]

    Kinleya) Department of Mechanical Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 and breakup of polymeric liquid jets. Newtonian jets rapidly neck down under capillary action and pinch off

  15. Technology available for license: Charging of liquid energy storage...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Technology available for license: Charging of liquid energy storage media through radiolysis (ANL-IN-14-036) January 23, 2015 Tweet EmailPrint This technology utilizes radiolysis...

  16. Keer electro-optic measurements in liquid dielectrics

    E-Print Network [OSTI]

    Zhang, Xuewei

    2014-01-01T23:59:59.000Z

    Kerr electro-optic technique has been used to measure the electric field distribution in high voltage stressed dielectric liquids, where the difference between refractive indices for light polarized parallel and perpendicular ...

  17. Photodegradation mechanisms of tetraphenyl butadiene coatings for liquid argon detectors

    E-Print Network [OSTI]

    Jones, Benjamin James Poyner

    We report on studies of degradation mechanisms of tetraphenyl butadiene (TPB) coatings of the type used in neutrino and dark matter liquid argon experiments. Using gas chromatography coupled to mass spectrometry we have ...

  18. Shear and Extensional Rheology of Cellulose/Ionic Liquid Solutions

    E-Print Network [OSTI]

    Haward, Simon J.

    In this study, we characterize the shear and extensional rheology of dilute to semidilute solutions of cellulose in the ionic liquid 1-ethyl-3-methylimidazolium acetate (EMIAc). In steady shear flow, the semidilute solutions ...

  19. Ionic Liquids as Novel Lubricant Additives for Next-Generation...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Ionic Liquids as Novel Lubricant Additives for Next-Generation Fuel-Efficient Engines May 15 2015 10:00 AM - 11:00 AM Jun Qu, Materials Science and Technology Division ORNL...

  20. Title of dissertation: HYDROMAGNETIC TURBULENT INSTABILITY IN LIQUID SODIUM

    E-Print Network [OSTI]

    Lathrop, Daniel P.

    ABSTRACT Title of dissertation: HYDROMAGNETIC TURBULENT INSTABILITY IN LIQUID SODIUM EXPERIMENTS Daniel R. Sisan, Doctor of Philosophy, 2004 Dissertation directed by: Professor Daniel P. Lathrop Department of Physics This dissertation describes the observation of magnetically-induced instabil- ities

  1. Advanced Chemical Heat Pumps Using Liquid-Vapor Reactions 

    E-Print Network [OSTI]

    Kirol, L.

    1987-01-01T23:59:59.000Z

    Chemical heat pumps utilizing liquid-vapor reactions can be configured in forms analogous to electric drive vapor-compression heat pumps and heat activated absorption heat pumps. Basic thermodynamic considerations eliminate some heat pumps and place...

  2. Liquid metal batteries : ambipolar electrolysis and alkaline earth electroalloying cells

    E-Print Network [OSTI]

    Bradwell, David (David Johnathon)

    2011-01-01T23:59:59.000Z

    Three novel forms of liquid metal batteries were conceived, studied, and operated, and their suitability for grid-scale energy storage applications was evaluated. A ZnlITe ambipolar electrolysis cell comprising ZnTe dissolved ...

  3. Design of biomimetic compliant devices for locomotion in liquid environments

    E-Print Network [OSTI]

    Valdivia y Alvarado, Pablo (Pablo Alvaro), 1977-

    2007-01-01T23:59:59.000Z

    Presently, there is a need for devices capable of autonomous locomotion in liquid environments. Humanitarian, industrial and defense applications are numerous and include examples such as search and rescue missions, ocean ...

  4. Low-Emissions Burner Technology using Biomass-Derived Liquid...

    Broader source: Energy.gov (indexed) [DOE]

    This factsheet describes a project that developed fuel-flexible, low-emissions burner technology capable of using biomass-derived liquid fuels, such as glycerin or fatty acids, as...

  5. Municipal Solid Waste (MSW) to Liquid Fuels Synthesis, Volume...

    Energy Savers [EERE]

    2: A Techno-economic Evaluation of the Production of Mixed Alcohols Municipal Solid Waste (MSW) to Liquid Fuels Synthesis, Volume 2: A Techno-economic Evaluation of the Production...

  6. Enhancing cholesteric liquid crystal laser performance using a cholesteric reflector

    E-Print Network [OSTI]

    Wu, Shin-Tson

    laser based on a free- standing film of photo polymerized cholesteric liquid crystal," Appl. Phys. Lett as an optic fiber-based temperature sensor," Appl. Phys. Lett. 85, 2691-2693 (2004). 15. Y. Huang, Y. Zhou

  7. Nuclear tanker producing liquid fuels from air and water

    E-Print Network [OSTI]

    Galle-Bishop, John Michael

    2011-01-01T23:59:59.000Z

    Emerging technologies in CO? air capture, high temperature electrolysis, microchannel catalytic conversion, and Generation IV reactor plant systems have the potential to create a shipboard liquid fuel production system ...

  8. Molecular Dynamics Modeling of Ionic Liquids in Electrospray Propulsion

    E-Print Network [OSTI]

    . Lozano June 2010 SSL # 6-10 #12;#12;Molecular Dynamics Modeling of Ionic Liquids in Electrospray Propulsion Nanako Takahashi, Paulo C. Lozano June 2010 SSL # 6-10 This work is based on the unaltered text

  9. The mathematical modeling of a Tuned Liquid Damper

    E-Print Network [OSTI]

    Tokarczyk, Bryan Lee

    1997-01-01T23:59:59.000Z

    The goal of this research is the simplification of the mathematical modeling process of a Tuned Liquid Damper. In an environment of increasingly flexible and lightly damped structures, the suppression of structural vibrations is an important topic...

  10. NUMERICAL SIMULATION OF RESERVOIR COMPACTION IN LIQUID DOMINATED GEOTHERMAL SYSTEMS

    E-Print Network [OSTI]

    Lippmann, M.J.

    2010-01-01T23:59:59.000Z

    13. modeling of liquid geothermal systems: Ph.D. thesis,of water dominated geothermal fields with large temper~of land subsidence in geothermal areas: Proc. 2nd Int. Symp.

  11. Liquidity and Asset Returns Under Asymmetric Information and Imperfect Competition

    E-Print Network [OSTI]

    Wang, Jiang

    We analyze how asymmetric information and imperfect competition affect liquidity and asset prices. Our model has three periods: Agents are identical in the first, become heterogeneous and trade in the second, and consume ...

  12. Stochastic and deterministic causes of streamer branching in liquid dielectrics

    E-Print Network [OSTI]

    Jadidian, Jouya

    Streamer branching in liquid dielectrics is driven by stochastic and deterministic factors. The presence of stochastic causes of streamer branching such as inhomogeneities inherited from noisy initial states, impurities, ...

  13. Turning methane into usable liquid fuel: Illinois Institute of...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    liquid fuel: Illinois Institute of Technology and Argonne to receive 2M for hybrid fuel cells August 4, 2014 Tweet EmailPrint Researchers from the US Department of Energy's...

  14. Nanoparticles at liquid interfaces: Rotational dynamics and angular locking

    SciTech Connect (OSTI)

    Razavi, Sepideh; Kretzschmar, Ilona [Department of Chemical Engineering, City College of City University of New York, New York, New York 10031 (United States)] [Department of Chemical Engineering, City College of City University of New York, New York, New York 10031 (United States); Koplik, Joel [Department of Physics and The Benjamin Levich Institute for Physico-chemical Hydrodynamics, City College of City University of New York, New York, New York 10031 (United States)] [Department of Physics and The Benjamin Levich Institute for Physico-chemical Hydrodynamics, City College of City University of New York, New York, New York 10031 (United States); Colosqui, Carlos E., E-mail: carlos.colosqui@stonybrook.edu [Department of Mechanical Engineering, Stony Brook University, Stony Brook, New York 11794 (United States)

    2014-01-07T23:59:59.000Z

    Nanoparticles with different surface morphologies that straddle the interface between two immiscible liquids are studied via molecular dynamics simulations. The methodology employed allows us to compute the interfacial free energy at different angular orientations of the nanoparticle. Due to their atomistic nature, the studied nanoparticles present both microscale and macroscale geometrical features and cannot be accurately modeled as a perfectly smooth body (e.g., spheres and cylinders). Under certain physical conditions, microscale features can produce free energy barriers that are much larger than the thermal energy of the surrounding media. The presence of these energy barriers can effectively “lock” the particle at specific angular orientations with respect to the liquid-liquid interface. This work provides new insights on the rotational dynamics of Brownian particles at liquid interfaces and suggests possible strategies to exploit the effects of microscale features with given geometric characteristics.

  15. A microprocessor driven liquid crystal graphics display for aircraft use

    E-Print Network [OSTI]

    Marzke, Lee Howard

    1984-01-01T23:59:59.000Z

    A complete graphics system for use in modular avionics is built around a liquid crystal flat panel display. Screen refresh is handled by display controller that provides a bit mapped representation of the display in RAM. ...

  16. Refining and End Use Study of Coal Liquids.

    SciTech Connect (OSTI)

    NONE

    1997-12-31T23:59:59.000Z

    Progress in a study to determine the most cost effective and suitable combination of existing petroleum refinery processes needed to make specification transportation fuels or blending stocks, from direct and indirect coal liquefaction product liquids is reported.

  17. accumulation capillary liquid: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    free standing liquid film. The force falls off as an inverse power law in particles separation. We derive and validate an explicit expression for this exponent whose magnitude is...

  18. acid liquid membrane: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    bulk solutions of polyelectrolyte bounded by semipermeable membranes and separated by a thin film of salt-free liquid. Although the membranes are neutral, the counter-ions of the...

  19. Temperature-dependent structural heterogeneity in calcium silicate liquids.

    SciTech Connect (OSTI)

    Benmore, C. J.; Weber, J. K. R.; Wilding, M. C.; Du, J.; Parise, J. B. (X-Ray Science Division); (Materials Development Inc.); (Aberystwyth Univ.); (State Univ. of New York at Stony Brook); (Univ. of North Texas)

    2010-12-07T23:59:59.000Z

    X-ray diffraction measurements performed on aerodynamically levitated CaSiO{sub 3} droplets have been interpreted using a structurally heterogeneous liquid-state model. When cooled, the high-temperature liquid shows evidence of the polymerization of edge shared Ca octahedra. Diffraction isosbestic points are used to characterize the polymerization process in the pair-distribution function. This behavior is linear in the high-temperature melt but exhibits rapid growth just above the glass transition temperature around 1.2T{sub g}. The heterogeneous liquid interpretation is supported by molecular-dynamics simulations which show the CaSiO{sub 3} glass has more edge-shared polyhedra and fewer corner shared polyhedra than the liquid model.

  20. Tunable-focus liquid lens controlled using a servo motor

    E-Print Network [OSTI]

    Wu, Shin-Tson

    operation, this liquid lens has potential applications in zoom lenses, auto beam steering, and eyeglasses lenses are useful for auto beam steering, cell phone cameras, eyeglasses, and other optical signal

  1. a Newtonian liquid surface Matthew Thrasher, Sunghwan Jung,

    E-Print Network [OSTI]

    Texas at Austin. University of

    a lubricating layer air. Figure 2 shows rebound nearly vertical small velocities and becomes more oblique larger into a mineral oil. 1 1 Thrasher, S. Y. Pang, C.­P. Chuu, Swinney, bouncing Newtonian liquid rebounding surface

  2. Ultrafast photo-acoustic spectroscopy of super-cooled liquids

    E-Print Network [OSTI]

    Klieber, Christoph

    2010-01-01T23:59:59.000Z

    Picosecond laser ultrasonic techniques for acoustic wave generation and detection were adapted to probe longitudinal and transverse acoustic waves in liquids at gigahertz frequencies. The experimental effort was designed ...

  3. LIQUID PHASE SINTERING OF IRON WITH COPPER BASE ALLOY POWDERS

    E-Print Network [OSTI]

    Chen, M.-H.

    2010-01-01T23:59:59.000Z

    Symposium on Powder Metallurgy - The Iron and Steel Inst.a Liquid Phase", Powder Metallurgy, 17 (33), 227 (1974). H.Other made by powder metallurgy techniques. ses to produce

  4. Spectroscopic investigations of hydrogen bond dynamics in liquid water

    E-Print Network [OSTI]

    Fecko, Christopher J., 1975-

    2004-01-01T23:59:59.000Z

    Many of the remarkable physical and chemical properties of liquid water are due to the strong influence hydrogen bonds have on its microscopic dynamics. However, because of the fast timescales involved, there are relatively ...

  5. Nanoscale electrostatic actuators in liquid electrolytes: analysis and experiment

    E-Print Network [OSTI]

    Kim, Doyoung

    2006-04-12T23:59:59.000Z

    The objective of this dissertation is to analytically model a parallel plate electrostatic actuator operating in a liquid electrolyte and experimentally verify the analysis. The model assumes the system remains in thermodynamic equilibrium during...

  6. Boiling and condensation in a liquid-filled enclosure

    E-Print Network [OSTI]

    Bar-Cohen Avram

    1971-01-01T23:59:59.000Z

    A combined experimental and analytical investigation of boiling and condensation in a liquid-filled enclosure, with water and Freon- 113 as the working fluids, is described. The operating characteristics of a boiling system, ...

  7. Designing liquid repellent surfaces for fabrics, feathers and fog

    E-Print Network [OSTI]

    Chhatre, Shreerang S. (Shreerang Sharad)

    2013-01-01T23:59:59.000Z

    Omniphobicity refers to a property of surfaces which are not wetted by water, oils, alcohols and other low surface tension liquids. Robust omniphobic surfaces can be applied in many areas including fabrics with chemical / ...

  8. Carbon Nanotube-Reinforced Thermotropic Liquid Crystal Polymer Nanocomposites

    E-Print Network [OSTI]

    Kim, Jun Young

    This paper focuses on the fabrication via simple melt blending of thermotropic liquid crystal polyester (TLCP) nanocomposites reinforced with a very small quantity of modified carbon nanotube (CNT) and the unique effects ...

  9. Kinetics and Solvent Effects in the Synthesis of Ionic Liquids

    E-Print Network [OSTI]

    Schleicher, Jay C.

    2007-12-12T23:59:59.000Z

    Ionic liquids (ILs) are being recognized as environmentally friendly ("green") solvents. However, their synthesis is often conducted in the very solvents that they will reportedly replace. This research has investigated the kinetics and solvent...

  10. The radiation chemistry of ionic liquids: a review

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Mincher, Bruce J.; Wishart, James F.

    2014-07-03T23:59:59.000Z

    Ionic liquids have received increasing attention as media for radiochemical separations. Recent literature includes examinations of the efficiencies and mechanisms of the solvent extraction of lanthanides, actinides and fission products into ionic liquid solutions. For radiochemical applications, including as replacement solvents for nuclear fuel reprocessing, a thorough understanding of the radiation chemistry of ionic liquids will be required. Such an understanding can be achieved based upon a combination of steady-state radiolysis experiments coupled with post-irradiation product identification and pulse-radiolysis experiments to acquire kinetic information. These techniques allow for the elucidation of radiolytic mechanisms. This contribution reviews the current ionic liquid radiation chemistry literature as it affects separations, with these considerations in mind.

  11. Dehydrogenation of liquid fuel in microchannel catalytic reactor

    DOE Patents [OSTI]

    Toseland, Bernard Allen (Coopersburg, PA); Pez, Guido Peter (Allentown, PA); Puri, Pushpinder Singh (Emmaus, PA)

    2010-08-03T23:59:59.000Z

    The present invention is an improved process for the storage and delivery of hydrogen by the reversible hydrogenation/dehydrogenation of an organic compound wherein the organic compound is initially in its hydrogenated state. The improvement in the route to generating hydrogen is in the dehydrogenation step and recovery of the dehydrogenated organic compound resides in the following steps: introducing a hydrogenated organic compound to a microchannel reactor incorporating a dehydrogenation catalyst; effecting dehydrogenation of said hydrogenated organic compound under conditions whereby said hydrogenated organic compound is present as a liquid phase; generating a reaction product comprised of a liquid phase dehydrogenated organic compound and gaseous hydrogen; separating the liquid phase dehydrogenated organic compound from gaseous hydrogen; and, recovering the hydrogen and liquid phase dehydrogenated organic compound.

  12. Reactor Neutrino Experiments with a Large Liquid Scintillator Detector

    E-Print Network [OSTI]

    Joachim Kopp; Manfred Lindner; Alexander Merle; Mark Rolinec

    2007-01-19T23:59:59.000Z

    We discuss several new ideas for reactor neutrino oscillation experiments with a Large Liquid Scintillator Detector. We consider two different scenarios for a measurement of the small mixing angle $\\theta_{13}$ with a mobile $\\bar{\

  13. Hydrocarbon Gas Liquids (HGL): Recent Market Trends and Issues

    Reports and Publications (EIA)

    2014-01-01T23:59:59.000Z

    Over the past five years, rapid growth in U.S. onshore natural gas and oil production has led to increased volumes of natural gas plant liquids (NGPL) and liquefied refinery gases (LRG). The increasing economic importance of these volumes, as a result of their significant growth in production, has revealed the need for better data accuracy and transparency to improve the quality of historical data and projections for supply, demand, and prices of these liquids, co-products, and competing products. To reduce confusion in terminology and improve its presentation of data, EIA has worked with industry and federal and state governments to clarify gas liquid terminology and has developed the term Hydrocarbon Gas Liquids, or HGL.

  14. Investigations of amino acid-based surfactants at liquid interfaces 

    E-Print Network [OSTI]

    Yang, Dengliang

    2005-11-01T23:59:59.000Z

    Herein are presented collective studies of amino acid-based surfactants, also known as lipoamino acids, at liquid interfaces. Chapter III describes an investigation of domain morphology of N-Stearoylglutamic acid (N-SGA) ...

  15. Liquid water: A very complex fluid H EUGENE STANLEY

    E-Print Network [OSTI]

    Stanley, H. Eugene

    Liquid water: A very complex fluid H EUGENE STANLEY Center for Polymer Studies and Department, M Canpolat, M Meyer, O Mishima, R Sadr-Lahijany, A Scala and F W Starr. It is also based on earlier

  16. Rényi entropy, mutual information, and fluctuation properties of Fermi liquids

    E-Print Network [OSTI]

    Swingle, Brian Gordon

    We compute the leading contribution to the ground-state Rényi entropy S[subscript ?] for a region of linear size L in a Fermi liquid in d dimensions. The result contains a universal boundary law violating term simply related ...

  17. Liquid Effluent Retention Facility (LERF) Final Hazard Category Determination

    SciTech Connect (OSTI)

    HUTH, L.L.

    2001-06-06T23:59:59.000Z

    The Liquid Effluent Retention Facility was designed to store 242-A Evaporator process condensate and other liquid waste streams for treatment at the 200 East Area Effluent Treatment Facility. The Liquid Effluent Retention Facility has been previously classified as a Category 3 Nonreactor Nuclear Facility. As defined in Hazard Categorization and Accident Analysis Techniques for Compliance with DOE Order 5480.23, Nuclear Safety Analysis Reports (DOE 1992, DOE 1997), Category 3 Nuclear Facilities have the potential for significant localized (radiological) consequences. However, based on current facility design, operations, and radioactive constituent concentrations, the Liquid Effluent Retention Facility does not have the potential for significant localized (radiological) consequences and is categorized as a Radiological Facility. This report documents the final hazard categorization process performed in accordance with DOE Order 5480.23, Nuclear Safety Analysis Reports. This report describes the current configuration and operations of the Liquid Effluent Retention Facility. Also included is a preliminary hazard categorization, which is based on current and proposed radioactive and hazardous material inventories, a preliminary hazards and accident analysis, and a final hazard category determination. The results of the hazards and accident analysis, based on the current configuration and operations of the Liquid Effluent Retention Facility and the current and proposed radioactive and hazardous material inventories, demonstrate that the Liquid Effluent Retention Facility does not have the potential for significant localized (radiological) consequences. Based on the final hazard category analysis, the Liquid Effluent Retention Facility is a Radiological Facility. The final hazard category determination is based on a comparative evaluation of the consequence basis for the Category 3 threshold quantities to the calculated consequences for credible releases The basis for the Category 3 threshold quantities is 10 rem-equivalent man at 30 meters (98 feet) (DOE 1992, DOE 1997). The calculated 12 hour consequences to an individual located at 30 meters (98 feet) for two credible scenarios, spray release and a pool release, are 3.50 rem and 1.32 rem, respectively, which based upon the original hazard categorization criteria (DOE 1992) classified the Liquid Effluent Retention Facility as a Radiological Facility. Comparison of the calculated 24 hour consequences to an individual located at 30 meters (98 feet) for two credible scenarios, spray release and a pool release, 7.00 rem and 2.64 rem respectively, confirmed the Liquid Effluent Retention Facility classification as a Radiological Facility under the current hazard categorization criteria (DOE 1997). Both result in dose consequence values less than the allowable, 10 rem, meeting the requirements for categorizing the Liquid Effluent Retention Facility as a Radiological Facility.

  18. Retrograde Melting and Internal Liquid Gettering in Silicon

    SciTech Connect (OSTI)

    Hudelson, Steve; Newman, Bonna K.; Bernardis, Sarah; Fenning, David P.; Bertoni, Mariana I.; Marcus, Matthew A.; Fakra, Sirine C.; Lai, Barry; Buonassisi, Tonio

    2011-07-01T23:59:59.000Z

    Retrograde melting (melting upon cooling) is observed in silicon doped with 3d transition metals, via synchrotron-based temperature-dependent X-ray microprobe measurements. Liquid metal-silicon droplets formed via retrograde melting act as efficient sinks for metal impurities dissolved within the silicon matrix. Cooling results in decomposition of the homogeneous liquid phase into solid multiple-metal alloy precipitates. These phenomena represent a novel pathway for engineering impurities in semiconductor-based systems.

  19. Algebraic spin liquid in an exactly solvable spin model

    SciTech Connect (OSTI)

    Yao, Hong; Zhang, Shou-Cheng; Kivelson, Steven A.; /Stanford U., Phys. Dept.

    2010-03-25T23:59:59.000Z

    We have proposed an exactly solvable quantum spin-3/2 model on a square lattice. Its ground state is a quantum spin liquid with a half integer spin per unit cell. The fermionic excitations are gapless with a linear dispersion, while the topological 'vison' excitations are gapped. Moreover, the massless Dirac fermions are stable. Thus, this model is, to the best of our knowledge, the first exactly solvable model of half-integer spins whose ground state is an 'algebraic spin liquid.'

  20. Use of silicon in liquid sintered silicon nitrides and sialons

    DOE Patents [OSTI]

    Raj, Rishi (Ithaca, NY); Baik, Sunggi (Ithaca, NY)

    1984-12-11T23:59:59.000Z

    This invention relates to the production of improved high density nitrogen based ceramics by liquid-phase densification of silicon nitride or a compound of silicon-nitrogen-oxygen-metal, e.g. a sialon. In the process and compositions of the invention minor amounts of finely divided silicon are employed together with the conventional liquid phase producing additives to enhance the densification of the resultant ceramic.

  1. Use of silicon in liquid sintered silicon nitrides and sialons

    DOE Patents [OSTI]

    Raj, R.; Baik, S.

    1984-12-11T23:59:59.000Z

    This invention relates to the production of improved high density nitrogen based ceramics by liquid-phase densification of silicon nitride or a compound of silicon-nitrogen-oxygen-metal, e.g. a sialon. In the process and compositions of the invention minor amounts of finely divided silicon are employed together with the conventional liquid phase producing additives to enhance the densification of the resultant ceramic. 4 figs.

  2. Membrane contactor assisted extraction/reaction process employing ionic liquids

    DOE Patents [OSTI]

    Lin, Yupo J. (Naperville, IL); Snyder, Seth W. (Lincolnwood, IL)

    2012-02-07T23:59:59.000Z

    The present invention relates to a functionalized membrane contactor extraction/reaction system and method for extracting target species from multi-phase solutions utilizing ionic liquids. One preferred embodiment of the invented method and system relates to an extraction/reaction system wherein the ionic liquid extraction solutions act as both extraction solutions and reaction mediums, and allow simultaneous separation/reactions not possible with prior art technology.

  3. Advanced Chemical Heat Pumps Using Liquid-Vapor Reactions

    E-Print Network [OSTI]

    Kirol, L.

    ADVANCED CHEMICAL HEAT PUMPS USING LIQUID-VAPOR REACTIONS LANCE KIROL Senior Program Specialist Idaho National Engineering Laboratory Idaho Falls, Idaho . ABSTRACT Chemical heat pumps utilizing liquid-vapor reactions can be configured... in forms analogous to electric drive vapor-compression heat pumps and heat activated absorption heat pumps. Basic thermodynamic considerations eliminate some heat pumps and place restrictive working fluid requirements on others, but two thermodynam...

  4. Liquid-phase compositions from vapor-phase analyses

    SciTech Connect (OSTI)

    Davis, W. Jr. (Oak Ridge Gaseous Diffusion Plant, TN (USA)); Cochran, H.D. (Oak Ridge National Lab., TN (USA))

    1990-02-01T23:59:59.000Z

    Arsenic normally is not considered to be a contaminant. However, because arsenic was found in many cylinders of UF{sub 6}, including in corrosion products, a study was performed of the distribution of the two arsenic fluorides, AsF{sub 3} and AsF{sub 5}, between liquid and vapor phases. The results of the study pertain to condensation or vaporization of liquid UF{sub 6}. This study includes use of various experimental data plus many extrapolations necessitated by the meagerness of the experimental data. The results of this study provide additional support for the vapor-liquid equilibrium model of J.M. Prausnitz and his coworkers as a means of describing the distribution of various impurities between vapor and liquid phases of UF{sub 6}. Thus, it is concluded that AsF{sub 3} will tend to concentrate in the liquid phase but that the concentration of AsF{sub 5} in the vapor phase will exceed its liquid-phase concentration by a factor of about 7.5, which is in agreement with experimental data. Because the weight of the liquid phase in a condensation operation may be in the range of thousands of times that of the vapor phase, most of any AsF{sub 5} will be in the liquid phase in spite of this separation factor of 7.5. It may also be concluded that any arsenic fluorides fed into a uranium isotope separation plant will either travel with other low-molecular-weight gases or react with materials present in the plant. 25 refs., 3 figs., 6 tabs.

  5. MISE AU POINT LES MOBILITS DES IONS DANS LES HYDROCARBURES LIQUIDES

    E-Print Network [OSTI]

    Boyer, Edmond

    495. MISE AU POINT LES MOBILITÉS DES IONS DANS LES HYDROCARBURES LIQUIDES Par JACQUES MATHIEU, JEAN hydrocarbures liquides, on étudie la variation de cette mobilité en fonction de la viscosité du liquide et de la des- cription des méthodes de mesures des mobilités ioniques dans le cas des hydrocarbures liquides et

  6. Fumigation with the Liquid Fumigants Carbon Tetrachloride, Ethylene Dichloride and Ethylene Dibromide 

    E-Print Network [OSTI]

    Anonymous

    1966-01-01T23:59:59.000Z

    Fumigation with the Liquid Fumigants Carbon Tetrachloride, Ethylene Dichloride and Ethylene Dibromide...

  7. Viscosity of liquid He-4 and quantum of circulation: Why and how are they related?

    E-Print Network [OSTI]

    V. S. L'vov; L. Skrbek

    2011-02-16T23:59:59.000Z

    The relationship between the apparently unrelated physical quantities -- kinematic viscosity of liquid He-4, $\

  8. LIQUID CRYSTAL THERMOGRAPHY ON THE FLUID SOLID INTERFACE OF ROTATING SYSTEMS

    E-Print Network [OSTI]

    Camci, Cengiz

    = Aluminum c = centrifugal lc = liquid crystal o = aerodynamic wall friction related p = at constant pressu

  9. Variable-focus liquid lens Hongwen Ren and Shin-Tson Wu

    E-Print Network [OSTI]

    Wu, Shin-Tson

    . Introduction Variable focus liquid lenses are attractive for cellular phone, camera, eyeglasses, and other

  10. The Efficiency of Liquidity Management in Islamic Banks (Conservative vs. Profit)

    E-Print Network [OSTI]

    The Efficiency of Liquidity Management in Islamic Banks (Conservative vs. Profit) Professor Abdul-Iraq) ABSTRACT The aim of this paper is to explaim and examines the liquidity efficiency in Islamic Banks to measure liquidity efficiency, where measurement of liquidity management efficiency helps in the planning

  11. 1. Theory for Liquid Heat Capacity I ) Polynomial equation (HC_CPLEQN)

    E-Print Network [OSTI]

    Hong, Deog Ki

    1. Theory for Liquid Heat Capacity I ) Polynomial equation (HC_CPLEQN) Polynomial equation is usedJ/kg-mol.K. II ) Corresponding States Method for Liquid Heat Capacity (HC_CPLCSP) The expression basedGraw-Hill, New York, 2000 2. KDB Routines for Liquid Heat Capacity Calculation KDB liquid heat capacity

  12. ARM: Microwave Radiometer data (MWR Profiles - QME), water vapor, temp, cloud liquid water, precip water retrievals

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Cadeddu, Maria

    Microwave Radiometer data (MWR Profiles - QME), water vapor, temp, cloud liquid water, precip water retrievals

  13. LIQUID PHASE DEPOSITION OF ELECTROCHROMIC THIN FILMS T. J. Richardson and M. D. Rubin

    E-Print Network [OSTI]

    , and readily scalable to larger substrates. Keywords: liquid phase deposition; electrochromic films; thin film

  14. Apparatus for detecting the presence of a liquid

    DOE Patents [OSTI]

    Kronberg, J.W.

    1993-01-01T23:59:59.000Z

    This invention is comprised of an apparatus for detecting the presence of a liquid in a region, including an electrically passive sensor adapted for contacting the liquid, and an electrically active detector. The sensor is a circuit with a pair of spaced-apart terminals connected to a switch that closes in the presence of the liquid. The detector carries an alternating current with a resonant frequency. When the sensor is placed in a region and liquid is present, the circuit of the sensor is closed. By bringing the detector close to the sensor, an alternating current is induced in the sensor that will, in turn, alter the resonant frequency of the detector. This change is signaled by a transducer. The switch can operate by a change in conductivity of a material between the terminals of the sensor or by expansion of a liquid absorber that pushes the two terminals together, or by a change in the conductivity of the space between the terminals as a result of the liquid. The detector generates an audible or visible signal, or both, in response to the current change.

  15. Apparatus and method for comparing corresponding acoustic resonances in liquids

    DOE Patents [OSTI]

    Sinha, Dipen N. (Los Almos, NM)

    1999-01-01T23:59:59.000Z

    Apparatus and method for comparing corresponding acoustic resonances in liquids. The present invention permits the measurement of certain characteristics of liquids which affect the speed of sound therein. For example, a direct correlation between the octane rating of gasoline and the speed of sound in a gasoline sample has been experimentally observed. Therefore, changes in the speed of sound therein can be utilized as a sensitive parameter for determining changes in composition of a liquid sample. The present apparatus establishes interference patterns inside of a liquid without requiring the use of very thin, rigorously parallel ceramic discs, but rather uses readily available piezoelectric transducers attached to the outside surface of the usual container for the liquid and located on the same side thereof in the vicinity of one another. That is, various receptacle geometries may be employed, and the driving and receiving transducers may be located on the same side of the receptacle. The cell may also be constructed of any material that is inert to the liquid under investigation. A single-transducer embodiment, where the same transducer provides the excitation to the sample container and receives signals impressed therein, is also described.

  16. Ionic liquids and electrochemistry: from proteins to electrochromic devices.

    SciTech Connect (OSTI)

    Keizer, T. S. (Timothy S.); McCleskey, T. M. (Thomas Mark); Baker, G. A. (Gary A.); Burrell, A. K. (Anthony K.); Baker, S. N. (Sheila N.); Warner, B. P. (Benjamin P.); Hall, S. B. (Simon B.)

    2004-01-01T23:59:59.000Z

    We will report on a wide range of activities within the chemistry division at Los Alamos National Laboratory. Results on basic and applied research involving electrochemistry will be discussed. Topics will include electrochemistry of proteins, sensors based on electrochemical signals, temperature sensors, electrochromic devices in ionic liquids and the characterization of organic cation radicals. We have recently developed several applications in ionic liquids that include electrochromic devices, temperature sensors and chemical sensors. The electrochromic windows are being marketed as selftinting automotive mirrors. The ionic liquid based temperature sensor is stable and accurate over a wide range and has the potential to provide high-resolution temperature imaging. Chemical sensors have been developed that use electrochemistry to detect low levels of potential chemical agents in air. We have also studied the basic chemistry of charge transfer complexes and proteins in ionic liquids. Charge transfer complexes display unique behavior in ionic liquid compare to traditional solvents. Proteins can be solubilized at high levels that make it possible to probe electrochemistry in the proper ionic liquid.

  17. VAPOR SPACE AND LIQUID/AIR INTERFACECORROSION TESTS

    SciTech Connect (OSTI)

    Zapp, P.; Hoffman, E.

    2009-11-09T23:59:59.000Z

    The phenomena of vapor space corrosion and liquid/air interface corrosion of carbon steel in simulated liquid waste environments have been investigated. Initial experiments have explored the hypothesis that vapor space corrosion may be accelerated by the formation of a corrosive electrolyte on the tank wall by a process of evaporation of relatively warmer waste and condensation of the vapor on the relatively cooler tank wall. Results from initial testing do not support the hypothesis of electrolyte transport by evaporation and condensation. The analysis of the condensate collected by a steel specimen suspended over a 40 C simulated waste solution showed no measurable concentrations of the constituents of the simulated solution and a decrease in pH from 14 in the simulant to 5.3 in the condensate. Liquid/air interface corrosion was studied as a galvanic corrosion system, where steel at the interface undergoes accelerated corrosion while steel in contact with bulk waste is protected. The zero-resistance-ammeter technique was used to measure the current flow between steel specimens immersed in solutions simulating (1) the high-pH bulk liquid waste and (2) the expected low-pH meniscus liquid at the liquid/air interface. Open-circuit potential measurements of the steel specimens were not significantly different in the two solutions, with the result that (1) no consistent galvanic current flow occurred and (2) both the meniscus specimen and bulk specimen were subject to pitting corrosion.

  18. Photorefractivity in polymer-stabilized nematic liquid crystals

    SciTech Connect (OSTI)

    Wiederrecht, G.P. [Argonne National Lab., IL (United States). Chemistry Div.; Wasielewski, M.R. [Argonne National Lab., IL (United States). Chemistry Div.]|[Northwestern Univ., Evanston, IL (United States). Dept. of Chemistry

    1998-07-01T23:59:59.000Z

    Polymer-stabilized liquid crystals, consisting of low concentrations of a polymeric electron acceptor, are shown to exhibit significantly enhanced photorefractive properties. The charge generation and transport properties of these composite systems are strongly modified from nematic liquid crystals doped with electron donors and acceptors. The new composites are produced by polymerizing a small quantity of a 1,4:5,8-naphthalenediimide electron acceptor functionalized with an acrylate group in an aligned nematic liquid crystal. Photopolymerization creates an anisotropic gel-like medium in which the liquid crystal is free to reorient in the presence of a space charge field, while maintaining charge trapping sites in the polymerized regions of the material. The presence of these trapping sites results in the observation of longer lived, higher resolution holographic gratings in the polymer-stabilized liquid crystals than observed in nematic liquid crystals alone. These gratings display Bragg regime diffraction. Asymmetric beam coupling, photo-conductivity, and four-wave mixing experiments are performed to characterize the photophysics of these novel materials.

  19. Apparatus and method for comparing corresponding acoustic resonances in liquids

    DOE Patents [OSTI]

    Sinha, D.N.

    1999-03-23T23:59:59.000Z

    Apparatus and method are disclosed for comparing corresponding acoustic resonances in liquids. The present invention permits the measurement of certain characteristics of liquids which affect the speed of sound therein. For example, a direct correlation between the octane rating of gasoline and the speed of sound in a gasoline sample has been experimentally observed. Therefore, changes in the speed of sound therein can be utilized as a sensitive parameter for determining changes in composition of a liquid sample. The present apparatus establishes interference patterns inside of a liquid without requiring the use of very thin, rigorously parallel ceramic discs, but rather uses readily available piezoelectric transducers attached to the outside surface of the usual container for the liquid and located on the same side thereof in the vicinity of one another. That is, various receptacle geometries may be employed, and the driving and receiving transducers may be located on the same side of the receptacle. The cell may also be constructed of any material that is inert to the liquid under investigation. A single-transducer embodiment, where the same transducer provides the excitation to the sample container and receives signals impressed therein, is also described. 5 figs.

  20. Apparatus for detecting the presence of a liquid

    DOE Patents [OSTI]

    Kronberg, James W. (Aiken, SC)

    1995-01-01T23:59:59.000Z

    An apparatus for detecting the presence of a liquid in a region, including an electrically passive sensor adapted for contacting the liquid, and an electrically active detector. The sensor is a circuit with a pair of spaced-apart terminals connected to a switch that closes in the presence of the liquid. The detector carries an alternating current with a resonant frequency. When the sensor is placed in a region and liquid is present in the region, the circuit of the sensor is closed. By bringing the detector close to the sensor, an alternating current is induced in the sensor that will, in turn, alter the resonant frequency of the detector. The change in the resonant frequency is signaled by a transducer. The switch can operate by a change in conductivity of a material between the terminals of the sensor or by expansion of a liquid absorber that pushes the two terminals together, or by a change in the conductivity of the space between the terminals as a result of the presence of the liquid. The detector generates an audible or visible signal, or both, in response to the change in current.