Sample records for licensing technical support

  1. Technical Support for Improving the Licensing Regulatory Base for Selected Facilities Associated with the Front End of the Fuel Cycle

    SciTech Connect (OSTI)

    Clark, R. G.; Schreiber, R. E.; Jamison, J. D.; Davenport, L. C.; Brite, D. W.

    1982-04-01T23:59:59.000Z

    Pacific Northwest Laboratory (PNL) was asked by the NRC Office of Nuclear Material Safety and Safeguards (NMSS) to determine the adequacy of its health, safety and environmental regulatory base as a guide to applicants for licenses to operate UF{sub 6} conversion facilities and fuel fabrication plants. The regulatory base was defined as the body of documented requirements and guidance to licensees, including laws passed by Congress, Federal Regulations developed by the NRC to implement the laws, license conditions added to each license to deal with special requirements for that specific license, and Regulatory Guides. The study concentrated on the renewal licensing accomplished in the last few years at five typical facilities, and included analyses of licensing documents and interviews with individuals involved with different aspects of the licensing process. Those interviewed included NMSS staff, Inspection and Enforcement (IE) officials, and selected licensees. From the results of the analyses and interviews, the PNL study team concludes that the regulatory base is adequate but should be codified for greater visibility. PNL recommends that NMSS clarify distinctions among legal requirements of the licensee, acceptance criteria employed by NMSS, and guidance used by all. In particular, a prelicensing conference among NMSS, IE and each licensee would be a practical means of setting license conditions acceptable to all parties.

  2. Licensing Support Network: An Electronic Discovery System

    SciTech Connect (OSTI)

    Gil, A. V.; Jensen, D.; McKinnon, B.

    2002-02-26T23:59:59.000Z

    The necessary authorization for the U. S. Department of Energy's (DOE) Office of Civilian Radioactive Waste Management (OCRWM) to submit a License Application (LA) is contingent upon the policy process defined in the Nuclear Waste Policy Act, as amended (NWPA), with some steps yet to occur. In spite of this uncertainty, the DOE must take prudent and appropriate action now, and over the next several years, to prepare for submittal of an application and to facilitate the U. S. Nuclear Regulatory Commission (NRC) review of this application, if the Yucca Mountain site is recommended and approved for repository development. One of these steps the DOE has taken involves working with the NRC's Advisory Review Panel to develop Licensing Support Network (LSN) requirements and guidelines. The NRC has made a prototype of the LSN web page available at www.LSNNET.gov. The OCRWM part of the LSN currently has an indefinite life cycle and may need to remain in existence until the repository is closed, which could be as long as 325 years.

  3. New York: EERE-Supported Catalyst Licensed for Use in Fuel Cell...

    Office of Environmental Management (EM)

    Supported Catalyst Licensed for Use in Fuel Cell Hybrid Advanced Vehicles New York: EERE-Supported Catalyst Licensed for Use in Fuel Cell Hybrid Advanced Vehicles January 24, 2014...

  4. Supporting Technical Documents | Department of Energy

    Office of Environmental Management (EM)

    Environmental Department (NMED) Los Alamos National Laboratory (LANL) Hazardous Waste Facility Permit Supporting Technical Document for the Radiological Release Accident...

  5. Net Zero Waste - Tools and Technical Support ...and other observations...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Net Zero Waste - Tools and Technical Support ...and other observations Net Zero Waste - Tools and Technical Support ...and other observations Presentation at Waste-to-Energy using...

  6. Department of Energy Technical Support Document National Environmental...

    Broader source: Energy.gov (indexed) [DOE]

    This Technical Support Document supplements the Department of Energy's (DOE's) Notice of Proposed Rulemaking. In this Technical Support Document, the Department of Energy presents...

  7. Technical Support and Transfer of Geothrmal Technical Knowledge and Information

    SciTech Connect (OSTI)

    John W. Lund

    2007-11-14T23:59:59.000Z

    The Geo-Heat Center (GHC) staff provided responses to 1442 technical support requests during the contract period (April 1, 2006 to September 30, 2007), which were six quarters under this contract. Our website, consisting of 1900 files, also contributes to our technical assistance activity. Downloaded files were 1,889,323 (3,448 per day) from our website, the total number of users was 1,365,258 (2,491 per day), and the total number of hits were 6,008,500 (10,064 per day). The GHC staff attended 60 workshops, short course and professional meeting and made 29 technical presentations. The staff also prepared and mailed out 2,000 copies of each of five issues of the GHC Quaterly Bulletin which contained 26 articles. We also mailed out approximately 5,000 papers and publications to interested individuals and organizations.

  8. DOE Awards Small Business Task Order for Technical Support to...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Contract Awarded to Small Business for Support Services DOE Awards Support Service Contract DOE Awards Small Business Task Order for Technical Support to the Office of...

  9. DOE Awards Small Business Task Order for Technical Support to...

    Energy Savers [EERE]

    for technical support services to TerranearPMC, LLC of Exton, PA to provide Spent Nuclear Fuel and Excess Nuclear Materials Disposition Planning technical support to the Office of...

  10. DOE Awards Small Business Task Order for Technical Support to...

    Broader source: Energy.gov (indexed) [DOE]

    nuclear energy research. Addthis Related Articles DOE Awards Support Service Contract DOE Awards Small Business Task Order for Technical Support to the Office of...

  11. ALARA Training for Technical Support Personnel

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742Energy China 2015ofDepartmentDepartment of2 of 5) ALARA Training for Technical Support Personnel

  12. ALARA Training for Technical Support Personnel

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742Energy China 2015ofDepartmentDepartment of2 of 5) ALARA Training for Technical Support Personnel3

  13. ALARA Training for Technical Support Personnel

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742Energy China 2015ofDepartmentDepartment of2 of 5) ALARA Training for Technical Support

  14. Research Call to DOE/Federal Laboratories: Technical Support...

    Office of Environmental Management (EM)

    Research Call to DOEFederal Laboratories: Technical Support for Interconnection-Level Electric Infrastructure Planning RC-BM-2010; Due May 3, 2010. Research Call to DOEFederal...

  15. DOE Awards Small Business Contract for Technical Support to the...

    Office of Environmental Management (EM)

    LLC of Idaho Falls, Idaho to provide technical support to the Office of Environmental Management. A time & materials task order will be issued from the master Indefinite...

  16. Radioactive sealed sources: Reasonable accountability, exemption, and licensing activity thresholds -- A technical basis

    SciTech Connect (OSTI)

    Lee, D.W. [Los Alamos National Lab., NM (United States); Shingleton, K.L. [Lawrence Livermore National Lab., CA (United States)

    1996-07-01T23:59:59.000Z

    Perhaps owing to their small size and portability, some radiation accidents/incidents have involved radioactive sealed sources (RSSs). As a result, programs for the control and accountability of RSSs have come to be recommended and emplaced that essentially require RSSs to be controlled in a manner different from bulk, unsealed radioactive material. Crucially determining the total number of RSSs for which manpower-intensive radiation protection surveillance is provided is the individual RSS activity above which such surveillance is required and below which such effort is not considered cost effective. Individual RSS activity thresholds are typically determined through scenarios which impart a chosen internal or external limiting dose to Reference Man under specified exposure conditions. The resultant RSS threshold activity levels have meaning commensurate with the assumed scenario exposure parameters, i.e., if they are realistic and technically based. A review of how the Department of Energy (DOE), the International Atomic Energy Agency (IAEA), and the Nuclear Regulatory Commission (NRC) have determined their respective accountability, exemption, and licensing threshold activity values is provided. Finally, a fully explained method using references readily available to practicing health physicists is developed using realistic, technically-based calculation parameters by which RSS threshold activities may be locally generated.

  17. Technical Qualification Program Description - Integrated Support...

    Broader source: Energy.gov (indexed) [DOE]

    to begin the 18 month qualification period). Technical Qualification Program Description Revision 2, November 2010 5 The position's inclusion in the TQP is: * Specified in the PD...

  18. ALARA Training for Technical Support Personnel

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742Energy China 2015ofDepartmentDepartment of2 of 5) ALARA Training for Technical

  19. U.S. DOE Approach to Address U.S. NRC Key Technical Issues for a License Application

    SciTech Connect (OSTI)

    Ziegler, J. D.; Gunter, T. C.; Gamble, R. P.; Bradbury, R. B.

    2003-02-25T23:59:59.000Z

    Interactions between the U.S. Department of Energy (DOE) staff and the U.S. Nuclear Regulatory Commission (NRC) staff prior to submittal of a license application (LA) for NRC review are focused on resolution of issues relevant to licensing a geologic repository at the Yucca Mountain site. These interactions take place in meetings that are open to the public, the State of Nevada, affected units of local government, and other interested parties. Consistent with a 1992 agreement between the DOE and NRC, resolution of an issue at the staff level can be achieved during the pre-licensing period when the NRC staff has no further questions or comments regarding how the DOE is addressing that issue. In no case does such resolution at the NRC staff level preclude an issue being raised during the licensing proceedings by the NRC or another party to the proceedings. Beginning in 1996, interactions between the DOE and NRC began to focus significant attention on the nine topical areas, called Key Technical Issues (KTIs), that the NRC staff considers to be important in evaluating the post-closure performance of a Yucca Mountain repository. DOENRC meetings to discuss each KTI and achieve technical agreement on the information needed to resolve the issues were held between August 2000 and September 2001. As a result of these meetings, 293 agreements were reached regarding information to be developed by the DOE to supplement the basis for NRC review of the initial LA.* As of April 23, 2003, 77 of these agreements are considered by the NRC to be complete based on information provided by the DOE.

  20. Wikis supporting PLM and Technical Documentation

    E-Print Network [OSTI]

    Høimyr, Nils-Joar; CERN. Geneva. IT Department

    2007-01-01T23:59:59.000Z

    Over the last years, Wikis have arisen as powerful tools for collaborative documentation on the Internet. The Encyclopaedia Wikipedia has become a reference, and the power of community editing in a Wiki allows for capture of knowledge from contributors all over the world. Use of a Wiki for Technical Documentation, along with hyper-links to other data sources such as a Product Lifecycle Management (PLM) system, provides a very effective collaboration tool as information can be easily feed into the system throughout the project life-cycle. In particular for software- and hardware projects with rapidly evolving documentation, the Wiki approach has proved to be successful. Certain Wiki implementations, such as TWiki, are project-oriented and include functionality such as automatic page revisioning. This paper addresses the use of TWiki to document hardware and software projects at CERN, from the requirements and brain-storming phase to end-product documentation. 2 examples are covered: large scale engineering for...

  1. Technical Data to Justify Full Burnup Credit in Criticality Safety Licensing Analysis

    SciTech Connect (OSTI)

    Enercon Services, Inc.

    2011-03-14T23:59:59.000Z

    Enercon Services, Inc. (ENERCON) was requested under Task Order No.2 to identify scientific and technical data needed to benchmark and justify Full Burnup Credit, which adds 16 fission products and 4 minor actinides1 to Actinide-Only burnup credit. The historical perspective for Full Burnup Credit is discussed, and interviews of organizations participating in burnup credit activities are summarized as a basis for identifying additional data needs and making recommendation. Input from burnup credit participants representing two segments of the commercial nuclear industry is provided. First, the Electric Power Research Institute (EPRI) has been very active in the development of Full Burnup Credit, representing the interests of nuclear utilities in achieving capacity gains for storage and transport casks. EPRI and its utility customers are interested in a swift resolution of the validation issues that are delaying the implementation of Full Burnup Credit [EPRI 2010b]. Second, used nuclear fuel storage and transportation Cask Vendors favor improving burnup credit beyond Actinide-Only burnup credit, although their discussion of specific burnup credit achievements and data needs was limited citing business sensitive and technical proprietary concerns. While Cask Vendor proprietary items are not specifically identified in this report, the needs of all nuclear industry participants are reflected in the conclusions and recommendations of this report. In addition, Oak Ridge National Laboratory (ORNL) and Sandia National Laboratory (SNL) were interviewed for their input into additional data needs to achieve Full Burnup Credit. ORNL was very open to discussions of Full Burnup Credit, with several telecoms and a visit by ENERCON to ORNL. For many years, ORNL has provided extensive support to the NRC regarding burnup credit in all of its forms. Discussions with ORNL focused on potential resolutions to the validation issues for the use of fission products. SNL was helpful in ENERCON's understanding of the difficult issues related to obtaining and analyzing additional cross section test data to support Full Burnup Credit. A PIRT (Phenomena Identification and Ranking Table) analysis was performed by ENERCON to evaluate the costs and benefits of acquiring different types of nuclear data in support of Full Burnup Credit. A PIRT exercise is a formal expert elicitation process with the final output being the ranking tables. The PIRT analysis (Table 7-4: Results of PIRT Evaluation) showed that the acquisition of additional Actinide-Only experimental data, although beneficial, was associated with high cost and is not necessarily needed. The conclusion was that the existing Radiochemical Assay (RCA) data plus the French Haut Taux de Combustion (HTC)2 and handbook Laboratory Critical Experiment (LCE) data provide adequate benchmark validation for Actinide-Only Burnup Credit. The PIRT analysis indicated that the costs and schedule to obtain sufficient additional experimental data to support the addition of 16 fission products to Actinide-Only Burnup Credit to produce Full Burnup Credit are quite substantial. ENERCON estimates the cost to be $50M to $100M with a schedule of five or more years. The PIRT analysis highlights another option for fission product burnup credit, which is the application of computer-based uncertainty analyses (S/U - Sensitivity/Uncertainty methodologies), confirmed by the limited experimental data that is already available. S/U analyses essentially transform cross section uncertainty information contained in the cross section libraries into a reactivity bias and uncertainty. Recent work by ORNL and EPRI has shown that a methodology to support Full Burnup Credit is possible using a combination of traditional RCA and LCE validation plus S/U validation for fission product isotopics and cross sections. Further, the most recent cross section data (ENDF/B-VII) can be incorporated into the burnup credit codes at a reasonable cost compared to the acquisition of equivalent experimental data. ENERCON concludes that even with the cos

  2. Technical support section annual work plan for FY 1996

    SciTech Connect (OSTI)

    Adkissson, B.P.; Allison, K.L.; Hess, R.A.; Kunselman, C.W.; Odom, S.M.; Smelcer, D.R.

    1996-04-01T23:59:59.000Z

    The Technical Support Section (TSS) of the Instrumentation and Controls (I&C) Division of Oak Ridge National Laboratory (ORNL) provides technical services such as fabrication, modification, installation, calibration, operation, repair, and preventive maintenance of instruments and other related equipment. Work performed by TSS is in support of basic and applied research and development (R&D), engineering and instrument and computer systems managed by ORNL. It is the mission of TSS to support programs and policies of ORNL, emphasizing safety and ensuring cost-effective support for R&D. Because the activities and priorities of TSS must be adapted to the technical support needs of ORNL, the TSS Annual Work Plan is derived from and driven directly by current trends in the budgets and activities of each ORNL division for which TSS provides support. Trends that will affect TSS planning during this period are reductions in the staffing levels of some R&D programs because of attrition or budget cuts and the establishment of new facilities or environmental safety and health programs. TSS does not have an annual budget to cover operating expenses incurred in providing instrumentation maintenance support to ORNL. Each year TSS contacts ORNL division finance managers or division finance officers to obtain information concerning projected funding levels of programs and facilities they manage. Although TSS has no direct responsibility for the maintenance or repair of real property, it does perform breakdown maintenance, preventive maintenance and calibration of laboratory, production, and experimental equipment, all of which is used for programmatic purposes. Operating expense funds from supported divisions support this type of equipment.

  3. Technical Support Section annual work plan for FY 1995

    SciTech Connect (OSTI)

    Adkisson, B.P.; Hess, R.A.; Kunselman, C.W.; Millet, A.J.; Smelcer, D.R.

    1994-10-01T23:59:59.000Z

    The Technical Support Section (TSS) of the Instrumentation and Controls (I and C) Division of Oak Ridge National Laboratory (ORNL) provides technical services such as fabrication, modification, installation, calibration, operation, repair, and preventive maintenance of instruments and other related equipment. Work performed by TSS is in support of basic and applied research and development (R and D), engineering, and instrument and computer systems managed by ORNL. Because the activities and priorities of TSS must be adapted to the technical support needs of ORNL, the TSS Annual Work Plan is derived from and driven directly by current trends in the budgets and activities of each ORNL division for which TSS provides support. Trends that will affect TSS planning during this period are reductions in the staffing levels of some R and D programs because of attrition or budget cuts and the establishment of new facilities or environmental safety and health programs. The ``Long-Range Work Plan`` is based on estimates of impact of the long-range priorities and directions of the Laboratory. Identifiable proposed new facilities and programs provide additional basis for long-range planning. After identifying long-range initiatives, TSS planning includes future training requirements, reevaluation of qualifications for new-hires, and identification of essential test equipment needed in new work.

  4. Residential Energy Code Technical Support: Training that Works for Enforcement Personnel

    E-Print Network [OSTI]

    Bowman, J.

    1988-01-01T23:59:59.000Z

    Comprehensive enforcement of residential state energy codes depends upon well designed and accessible technical support programs. This paper will explore the challenges of technical program development and delivery, and the solicitation of support...

  5. (Technical and engineering support for the Office of Industrial Programs)

    SciTech Connect (OSTI)

    Not Available

    1991-01-01T23:59:59.000Z

    As of April 19, 1991, technical, operational and analytic support and assistance to the offices and divisions of the Office of Renewable Energy, under contract DE-AC01-86CE30844 was completed. The overall work effort, initiated February 20, 1986, was characterized by timely, comprehensive, high quality, professional responsiveness to a broad range of renewable energy program operational support requirements. These are no instances of failure to respond, nor unacceptable response, during the five-year period. The technology program areas covered are Solar Buildings Technology, Wind Energy Technology, Photovoltaic Energy Technology, Geothermal Energy Technology, Biofuels and Municipal Waste Technology, Solar Thermal Technology, Hydropower Energy Technology, Ocean Energy Technology, and Electric Energy Systems and Energy Storage. The analytical and managerial support provided to the office and staff of the Deputy Assistant Secretary for Renewable Energy enabled a comprehensive evaluation of program and policy alternatives, and the selection and execution of appropriate courses of action from amongst those alternatives. Largely through these means the Office has been able to maintain continuity and a meaningful program thrust through the vacillations of policies and budgets that it has experienced over that it has experienced over the past five years. Appended are summaries of support activities within each of the individual technology program areas, as well as a complete listing of all project deliverables and due-dates for each submittal under the contract.

  6. Task Order Awarded for Technical and Safety Support Services...

    Broader source: Energy.gov (indexed) [DOE]

    Order Awarded for Environmental Technical Services DOE Issues Request for Quotations for Depleted Uranium Hexafluoride Conversion Technical Services DOE Awards Small Business...

  7. Large Hospital 50% Energy Savings: Technical Support Document

    SciTech Connect (OSTI)

    Bonnema, E.; Studer, D.; Parker, A.; Pless, S.; Torcellini, P.

    2010-09-01T23:59:59.000Z

    This Technical Support Document documents the technical analysis and design guidance for large hospitals to achieve whole-building energy savings of at least 50% over ANSI/ASHRAE/IESNA Standard 90.1-2004 and represents a step toward determining how to provide design guidance for aggressive energy savings targets. This report documents the modeling methods used to demonstrate that the design recommendations meet or exceed the 50% goal. EnergyPlus was used to model the predicted energy performance of the baseline and low-energy buildings to verify that 50% energy savings are achievable. Percent energy savings are based on a nominal minimally code-compliant building and whole-building, net site energy use intensity. The report defines architectural-program characteristics for typical large hospitals, thereby defining a prototype model; creates baseline energy models for each climate zone that are elaborations of the prototype models and are minimally compliant with Standard 90.1-2004; creates a list of energy design measures that can be applied to the prototype model to create low-energy models; uses industry feedback to strengthen inputs for baseline energy models and energy design measures; and simulates low-energy models for each climate zone to show that when the energy design measures are applied to the prototype model, 50% energy savings (or more) are achieved.

  8. Webinar: Energy Conservation Standards for Dehumidifiers; Availability of the Preliminary Technical Support Document

    Broader source: Energy.gov [DOE]

    DOE is conducting a public meeting and webinar for the availability of the preliminary technical support document regarding energy conservation standards for residential dehumidifiers. 79 FR 29380 ...

  9. Human System Simulation in Support of Human Performance Technical Basis at NPPs

    SciTech Connect (OSTI)

    David Gertman; Katya Le Blanc; alan mecham; william phoenix; Magdy Tawfik; Jeffrey Joe

    2010-06-01T23:59:59.000Z

    This paper focuses on strategies and progress toward establishing the Idaho National Laboratory’s (INL’s) Human Systems Simulator Laboratory at the Center for Advanced Energy Studies (CAES), a consortium of Idaho State Universities. The INL is one of the National Laboratories of the US Department of Energy. One of the first planned applications for the Human Systems Simulator Laboratory is implementation of a dynamic nuclear power plant simulation (NPP) where studies of operator workload, situation awareness, performance and preference will be carried out in simulated control rooms including nuclear power plant control rooms. Simulation offers a means by which to review operational concepts, improve design practices and provide a technical basis for licensing decisions. In preparation for the next generation power plant and current government and industry efforts in support of light water reactor sustainability, human operators will be attached to a suite of physiological measurement instruments and, in combination with traditional Human Factors Measurement techniques, carry out control room tasks in simulated advanced digital and hybrid analog/digital control rooms. The current focus of the Human Systems Simulator Laboratory is building core competence in quantitative and qualitative measurements of situation awareness and workload. Of particular interest is whether introduction of digital systems including automated procedures has the potential to reduce workload and enhance safety while improving situation awareness or whether workload is merely shifted and situation awareness is modified in yet to be determined ways. Data analysis is carried out by engineers and scientists and includes measures of the physical and neurological correlates of human performance. The current approach supports a user-centered design philosophy (see ISO 13407 “Human Centered Design Process for Interactive Systems, 1999) wherein the context for task performance along with the requirements of the end-user are taken into account during the design process and the validity of design is determined through testing of real end users

  10. Technical Support Document: 50% Energy Savings for Small Office Buildings

    SciTech Connect (OSTI)

    Thornton, Brian A.; Wang, Weimin; Huang, Yunzhi; Lane, Michael D.; Liu, Bing

    2010-04-30T23:59:59.000Z

    The Technical Support Document (TSD) for 50% energy savings in small office buildings documents the analysis and results for a recommended package of energy efficiency measures (EEMs) referred to as the advanced EEMs. These are changes to a building design that will reduce energy usage. The package of advanced EEMs achieves a minimum of 50% energy savings and a construction area weighted average energy savings of 56.6% over the ANSI/ASHRAE/IESNA Standard 90.1-2004 for 16 cities which represent the full range of climate zones in the United States. The 50% goal is for site energy usage reduction. The weighted average is based on data on the building area of construction in the various climate locations. Cost-effectiveness of the EEMs is determined showing an average simple payback of 6.7 years for all 16 climate locations. An alternative set of results is provided which includes a variable air volume HVAC system that achieves at least 50% energy savings in 7 of the 16 climate zones with a construction area weighted average savings of 48.5%. Other packages of EEMs may also achieve 50% energy savings; this report does not consider all alternatives but rather presents at least one way to reach the goal. Design teams using this TSD should follow an integrated design approach and utilize additional analysis to evaluate the specific conditions of a project.

  11. Technical Support Document for Version 3.6.1 of the COMcheck Software

    SciTech Connect (OSTI)

    Bartlett, Rosemarie; Connell, Linda M.; Gowri, Krishnan; Halverson, Mark A.; Lucas, Robert G.; Richman, Eric E.; Schultz, Robert W.; Winiarski, David W.

    2009-09-29T23:59:59.000Z

    This technical support document (TSD) is designed to explain the technical basis for the COMcheck software as originally developed based on the ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989). Documentation for other national model codes and standards and specific state energy codes supported in COMcheck has been added to this report as appendices. These appendices are intended to provide technical documentation for features specific to the supported codes and for any changes made for state-specific codes that differ from the standard features that support compliance with the national model codes and standards.

  12. DOE Selects 8(a) Small Business for Technical Support Services...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Articles DOE Awards Small Business Contract to Support Cleanup of New York West Valley Demonstration Project DOE Awards Support Service Contract DOE Awards Small Business...

  13. Grocery Store 50% Energy Savings Technical Support Document

    SciTech Connect (OSTI)

    Leach, M.; Hale, E.; Hirsch, A.; Torcellini, P.

    2009-09-01T23:59:59.000Z

    This report documents technical analysis for grocery stores aimed at providing design guidance that achieves whole-building energy savings of at least 50% over ASHRAE Standard 90.1-2004.

  14. General Merchandise 50% Energy Savings Technical Support Document

    SciTech Connect (OSTI)

    Hale, E.; Leach, M.; Hirsch, A.; Torcellini, P.

    2009-09-01T23:59:59.000Z

    This report documents technical analysis for medium-box general merchandise stores aimed at providing design guidance that achieves whole-building energy savings of at least 50% over ASHRAE Standard 90.1-2004.

  15. Instrumentation and Controls Division, Technical Support Department Management Plan, FY 1993--FY 1996

    SciTech Connect (OSTI)

    Adkisson, B.P.; Kunselman, C.W.; Effler, R.P.; Miller, D.R.; Millet, A.J.; Stansberry, C.T.

    1993-08-01T23:59:59.000Z

    This report describes the organization, key functions, and major activities of the Technical Support Department The Department is the programmatic support element of the Instrumentation and Controls Division. The Department`s primary focus is the support of existing equipment and systems at Oak Ridge National Laboratory that are generally characterized as instrumentation and controls. The support takes the form of repair, calibration, fabrication, field engineering, preventive maintenance, software support, and record keeping.

  16. The CHPRC Groundwater and Technical Integration Support (Master Project) Quality Assurance Management Plan

    SciTech Connect (OSTI)

    Fix, N. J.

    2009-04-03T23:59:59.000Z

    The scope of the CH2M Hill Plateau Remediation Company, LLC (CHPRC) Groundwater and Technical Integration Support (Master Project) is for Pacific Northwest National Laboratory staff to provide technical and integration support to CHPRC. This work includes conducting investigations at the 300-FF-5 Operable Unit and other groundwater operable units, and providing strategic integration, technical integration and assessments, remediation decision support, and science and technology. The projects under this Master Project will be defined and included within the Master Project throughout the fiscal year, and will be incorporated into the Master Project Plan. This Quality Assurance Management Plan provides the quality assurance requirements and processes that will be followed by the CHPRC Groundwater and Technical Integration Support (Master Project) and all releases associated with the CHPRC Soil and Groundwater Remediation Project. The plan is designed to be used exclusively by project staff.

  17. Puerto Rico Aqueduct and Sewer Authority General Consulting Services and Technical Support

    E-Print Network [OSTI]

    Gilbes, Fernando

    Puerto Rico Aqueduct and Sewer Authority General Consulting Services and Technical Support, and environmental engineering courses at various engineering schools in Puerto Rico. His work experience includes of Puerto Rico, PSC. (Managing Engineer) (2005- Present) Management of environmental services including

  18. High-Btu gas from peat. A feasibility study. Task 11. Technical support. Final report

    SciTech Connect (OSTI)

    Not Available

    1982-05-01T23:59:59.000Z

    In September 1980, the US Department of Energy awarded grant No. DE-FG01-80RA50348 to the Minnesota Gas Company (Minnegasco) to evaluate the commercial viability - technical, economic and environmental - of producing 80 million SCF/day of substitute natural gas (SNG) from peat. Minnegasco's project team for this study consisted of Dravo Engineers and Constructors (for design, engineering and economics of peat harvesting, dewatering and gasification systems); Ertec, Inc. (for environmental and socioeconomic analyses); Institute of Gas Technology (for gasification process information, and technical and engineering support). This report presents the work conducted under Task II (Technical Support) by the Institute of Gas Technology (IGT), the developer of the PEATGAS process, which was selected for the study. Task achievements are presented for: gasifier design and performance; technical support; and task management. 12 figures, 22 tables.

  19. Technical Support Document: Development of the Advanced Energy Design Guide for Small Hospitals and Healthcare Facilities--30% Guide

    SciTech Connect (OSTI)

    Bonnema, E.; Doebber, I.; Pless, S.; Torcellini, P.

    2010-03-01T23:59:59.000Z

    This Technical Support Document describes the process and methodology for the development of the Advanced Energy Design Guide for Small Hospitals and Healthcare Facilities.

  20. The Planning, Licensing, Modifications, and Use of a Russian Vessel for Shipping Spent Nuclear Fuel by Sea in Support of the DOE RRRFR Program

    SciTech Connect (OSTI)

    Michael Tyacke; Dr. Igor Bolshinsky; Wlodzimierz Tomczak; Sergey Naletov; Oleg Pichugin

    2001-10-01T23:59:59.000Z

    The Russian Research Reactor Fuel Return (RRRFR) Program, under the U.S. Department of Energy’s Global Threat Reduction Initiative, began returning Russian-supplied high-enriched uranium (HEU) spent nuclear fuel (SNF), stored at Russian-designed research reactors throughout the world, to Russia in January 2006. During the first years of making HEU SNF shipments, it became clear that the modes of transportation needed to be expanded from highway and railroad to include sea and air to meet the extremely aggressive commitment of completing the first series of shipments by the end of 2010. The first shipment using sea transport was made in October 2008 and used a non-Russian flagged vessel. The Russian government reluctantly allowed a one-time use of the foreign-owned vessel into their highly secured seaport, with the understanding that any future shipments would be made using a vessel owned and operated by a Russian company. ASPOL-Baltic of St. Petersburg, Russia, owns and operates a small fleet of vessels and has a history of shipping nuclear materials. ASPOL-Baltic’s vessels were licensed for shipping nuclear materials; however, they were not licensed to transport SNF materials. After a thorough review of ASPOL Baltic’s capabilities and detailed negotiations, it was agreed that a contract would be let with ASPOL-Baltic to license and refit their MCL Trader vessel for hauling SNF in support of the RRRFR Program. This effort was funded through a contract between the RRRFR Program, Idaho National Laboratory, and Radioactive Waste Management Plant of Swierk, Poland. This paper discusses planning, Russian and international maritime regulations and requirements, Russian authorities’ reviews and approvals, licensing, design, and modifications made to the vessel in preparation for SNF shipments. A brief summary of actual shipments using this vessel, experiences, and lessons learned also are described.

  1. 1E Wind Energy Program: Technical Information and Outreach Support Final Technical Report

    SciTech Connect (OSTI)

    Arnold, Abigail

    2006-03-09T23:59:59.000Z

    A U.S. consensus-based collaborative formed in 1994, the National Wind Coordinating Committee (NWCC) identifies issues that affect the use of wind power, establishes dialogue among key stakeholders, and catalyzes appropriate activities to support the development of environmentally, economically, and politically sustainable commercial markets for wind power. NWCC members include representatives from electric utilities and support organizations, state legislatures, state utility commissions, consumer advocacy offices, wind equipment suppliers and developers, green power marketers, environmental organizations, agriculture and economic development organizations, and state and federal agencies.

  2. LIST OF DECOMMISSIONING LESSONS-LEARNED IN SUPPORT OF THE DEVELOPMENT OF A STANDARD REVIEW PLAN FOR NEW REACTOR LICENSING

    E-Print Network [OSTI]

    Memorandum To; David B. Matthews; Elmo E. Collins

    2006-01-01T23:59:59.000Z

    Staff in the Division of New Reactor Licensing (DNRL) requested assistance from the Division of Waste Management and Environmental Protection (DWMEP) in the development of a standard review plan (SRP) for the licensing of new reactor facilities. Specifically, DNRL staff requested a list of high-level decommissioning lessons-learned that new applicants for a reactor license should address in order to minimize, to the extent practicable, contamination of the facility and the environment, facilitate eventual decommissioning, and minimize, to the extent practicable, the generation of radioactive waste. DWMEP staff met with your staff several times to discuss and clarify the requested input. This requested information is provided in Enclosure 1. I would like to bring to your attention other sources of decommissioning lessons-learned. The list of lessons-learned provided in Enclosure 1 is a subset of a much larger set of decommissioning lessons-learned. DWMEP developed the list in Enclosure 1 by reviewing the lessons-learned described in other documents (Enclosure 2) and selecting those it felt were most significant, based on DWMEP decommissioning experience. Additionally, the Electric Power Research Institute (EPRI) has developed decommissioning lessons-learned. DWMEP has not reviewed those lessons-learned because they are considered proprietary information by EPRI. DWMEP staff also developed a comprehensive bibliography of documents containing decommissioning lessons-learned. The bibliography is posted on the Nuclear Regulatory Commission’s public website. CONTACT: Rafael L. Rodriguez, NMSS/DWMEP

  3. Technical Support Document for Version 3.9.1 of the COMcheck Software

    SciTech Connect (OSTI)

    Bartlett, Rosemarie; Connell, Linda M.; Gowri, Krishnan; Halverson, Mark A.; Lucas, Robert G.; Richman, Eric E.; Schultz, Robert W.; Winiarski, David W.

    2012-09-01T23:59:59.000Z

    COMcheck provides an optional way to demonstrate compliance with commercial and high-rise residential building energy codes. Commercial buildings include all use groups except single family and multifamily not over three stories in height. COMcheck was originally based on ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989) requirements and is intended for use with various codes based on Standard 90.1, including the Codification of ASHRAE/IES Standard 90.1-1989 (90.1-1989 Code) (ASHRAE 1989a, 1993b) and ASHRAE/IESNA Standard 90.1-1999 (Standard 90.1-1999). This includes jurisdictions that have adopted the 90.1-1989 Code, Standard 90.1-1989, Standard 90.1-1999, or their own code based on one of these. We view Standard 90.1-1989 and the 90.1-1989 Code as having equivalent technical content and have used both as source documents in developing COMcheck. This technical support document (TSD) is designed to explain the technical basis for the COMcheck software as originally developed based on the ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989). Documentation for other national model codes and standards and specific state energy codes supported in COMcheck has been added to this report as appendices. These appendices are intended to provide technical documentation for features specific to the supported codes and for any changes made for state-specific codes that differ from the standard features that support compliance with the national model codes and standards. Beginning with COMcheck version 3.8.0, support for 90.1-1989, 90.1-1999, and the 1998 IECC and version 3.9.0 support for 2000 and 2001 IECC are no longer included, but those sections remain in this document for reference purposes.

  4. Technical support for amending standards for management of uranium byproduct materials: 40 cfr part 192-subpart d. Background information document

    SciTech Connect (OSTI)

    Not Available

    1993-10-01T23:59:59.000Z

    The Environmental Protection Agency (EPA) is amending 40 CFR 192, Subpart D, dealing with disposal of uranium mill tailings at non-operational sites licensed by the Nuclear Regulatory Commission (NRC) or an agreement state pursuant to the Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978. The Background Information Document (BID) was prepared in support of the rulemaking proceedings for EPA's action. The BID only considers long-term disposal of tailings at facilities licensed by the NRC or an agreement state, and designated Title II facilities in the UMTRCA.

  5. Technical Support Document for Version 3.9.0 of the COMcheck Software

    SciTech Connect (OSTI)

    Bartlett, Rosemarie; Connell, Linda M.; Gowri, Krishnan; Halverson, Mark A.; Lucas, R. G.; Richman, Eric E.; Schultz, Ralph W.; Winiarski, David W.

    2011-09-01T23:59:59.000Z

    COMcheck provides an optional way to demonstrate compliance with commercial and high-rise residential building energy codes. Commercial buildings include all use groups except single family and multifamily not over three stories in height. COMcheck was originally based on ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989) requirements and is intended for use with various codes based on Standard 90.1, including the Codification of ASHRAE/IES Standard 90.1-1989 (90.1-1989 Code) (ASHRAE 1989a, 1993b) and ASHRAE/IESNA Standard 90.1-1999 (Standard 90.1-1999). This includes jurisdictions that have adopted the 90.1-1989 Code, Standard 90.1-1989, Standard 90.1-1999, or their own code based on one of these. We view Standard 90.1-1989 and the 90.1-1989 Code as having equivalent technical content and have used both as source documents in developing COMcheck. This technical support document (TSD) is designed to explain the technical basis for the COMcheck software as originally developed based on the ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989). Documentation for other national model codes and standards and specific state energy codes supported in COMcheck has been added to this report as appendices. These appendices are intended to provide technical documentation for features specific to the supported codes and for any changes made for state-specific codes that differ from the standard features that support compliance with the national model codes and standards. Beginning with COMcheck version 3.8.0, support for 90.1-1989, 90.1-1999, and the 1998 IECC are no longer included, but those sections remain in this document for reference purposes.

  6. Technical Issues Map for the NHI System Interface and Support Systems Area: 3rd Quarter FY 07

    SciTech Connect (OSTI)

    Steven R. Sherman

    2007-06-01T23:59:59.000Z

    This document provides a mapping of technical issues associated with development of the Next Generation Nuclear Plant (NGNP) intermediate heat transport loop and nuclear hydrogen plant support systems to the work that has been accomplished or is currently underway. The technical issues are ranked according to priority and by assumed resolution dates. Due to funding limitations, not all high-priority technical issues are under study at the present time, and more resources will need to be dedicated to tackling such issues in the future. This technical issues map is useful for understanding the relative importance of various technical challenges and will be used as a planning tool by the NHI technical leadership for future work package planning. The technical map in its present form will be discontinued in FY08 and will be folded into a larger NHI System Interface and Support Systems project management plan and scope baseline statement in FY08.

  7. Sample Licensing Agreements | Partnerships | ORNL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    be modified to meet individual circumstances. Licensing Agreements Nonexclusive Patent License Exclusive Patent License Nonexclusive Copyright License Nondisclosure (NDA)...

  8. Technical Issues Map for the NHI System Interface and Support Systems Area: 1st Quarter FY 07

    SciTech Connect (OSTI)

    Steven R. Sherman

    2006-12-01T23:59:59.000Z

    This document provides a mapping of technical issues associated with development of the Next Generation Nuclear Plant (NGNP) intermediate heat transport loop and nuclear hydrogen plant support systems to the work that has been accomplished or is currently underway. The technical issues are ranked according to priority and by assumed resolution dates. Due to funding limitations, not all high-priority technical issues are under study at the present time, and more resources will need to be dedicated to tackling such issues in the future. This technical issues map is useful for understanding the relative importance of various technical challenges and will be used as a planning tool for future work package planning.

  9. Technical Support Document for Version 3.4.0 of the COMcheck Software

    SciTech Connect (OSTI)

    Bartlett, Rosemarie; Connell, Linda M.; Gowri, Krishnan; Halverson, Mark A.; Lucas, Robert G.; Richman, Eric E.; Schultz, Robert W.; Winiarski, David W.

    2007-09-14T23:59:59.000Z

    COMcheck provides an optional way to demonstrate compliance with commercial and high-rise residential building energy codes. Commercial buildings include all use groups except single family and multifamily not over three stories in height. COMcheck was originally based on ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989) requirements and is intended for use with various codes based on Standard 90.1, including the Codification of ASHRAE/IES Standard 90.1-1989 (90.1-1989 Code) (ASHRAE 1989a, 1993b) and ASHRAE/IESNA Standard 90.1-1999 (Standard 90.1-1999). This includes jurisdictions that have adopted the 90.1-1989 Code, Standard 90.1-1989, Standard 90.1-1999, or their own code based on one of these. We view Standard 90.1-1989 and the 90.1-1989 Code as having equivalent technical content and have used both as source documents in developing COMcheck. This technical support document (TSD) is designed to explain the technical basis for the COMcheck software as originally developed based on the ANSI/ASHRAE/IES Standard 90.1-1989 (Standard 90.1-1989). Documentation for other national model codes and standards and specific state energy codes supported in COMcheck has been added to this report as appendices. These appendices are intended to provide technical documentation for features specific to the supported codes and for any changes made for state-specific codes that differ from the standard features that support compliance with the national model codes and standards.

  10. Material Not Categorized As Waste (MNCAW) data report. Radioactive Waste Technical Support Program

    SciTech Connect (OSTI)

    Casey, C.; Heath, B.A.

    1992-11-01T23:59:59.000Z

    The Department of Energy (DOE), Headquarters, requested all DOE sites storing valuable materials to complete a questionnaire about each material that, if discarded, could be liable to regulation. The Radioactive Waste Technical Support Program entered completed questionnaires into a database and analyzed them for quantities and type of materials stored. This report discusses the data that TSP gathered. The report also discusses problems revealed by the questionnaires and future uses of the data. Appendices contain selected data about material reported.

  11. Technical Support Document: 50% Energy Savings Design Technology Packages for Highway Lodging Buildings

    SciTech Connect (OSTI)

    Jiang, Wei; Gowri, Krishnan; Lane, Michael D.; Thornton, Brian A.; Rosenberg, Michael I.; Liu, Bing

    2009-09-28T23:59:59.000Z

    This Technical Support Document (TSD) describes the process, methodology and assumptions for development of the 50% Energy Savings Design Technology Packages for Highway Lodging Buildings, a design guidance document intended to provide recommendations for achieving 50% energy savings in highway lodging properties over the energy-efficiency levels contained in ANSI/ASHRAE/IESNA Standard 90.1-2004, Energy Standard for Buildings Except Low-Rise Residential Buildings.

  12. Technical Support Document: 50% Energy Savings Design Technology Packages for Medium Office Buildings

    SciTech Connect (OSTI)

    Thornton, Brian A.; Wang, Weimin; Lane, Michael D.; Rosenberg, Michael I.; Liu, Bing

    2009-09-01T23:59:59.000Z

    This Technical Support Document (TSD) describes the process and methodology for development of the Advanced Energy Design Guide for Medium Offices (AEDG-MO or the Guide), a design guidance document which intends to provide recommendations for achieving 50% energy savings in medium office buildings that just meet the requirements of ANSI/ASHRAE/IESNA Standard 90.1-2004, Energy Standard for Buildings Except Low-Rise Residential Buildings.

  13. Technology status in support of refined technical baseline for the Spent Nuclear Fuel project. Revision 1

    SciTech Connect (OSTI)

    Puigh, R.J.; Toffer, H.; Heard, F.J.; Irvin, J.J.; Cooper, T.D.

    1995-10-20T23:59:59.000Z

    The Spent Nuclear Fuel Project (SNFP) has undertaken technology acquisition activities focused on supporting the technical basis for the removal of the N Reactor fuel from the K Basins to an interim storage facility. The purpose of these technology acquisition activities has been to identify technology issues impacting design or safety approval, to establish the strategy for obtaining the necessary information through either existing project activities, or the assignment of new work. A set of specific path options has been identified for each major action proposed for placing the N Reactor fuel into a ``stabilized`` form for interim storage as part of this refined technical basis. This report summarizes the status of technology information acquisition as it relates to key decisions impacting the selection of specific path options. The following specific categories were chosen to characterize and partition the technology information status: hydride issues and ignition, corrosion, hydrogen generation, drying and conditioning, thermal performance, criticality and materials accountability, canister/fuel particulate behavior, and MCO integrity. This report represents a preliminary assessment of the technology information supporting the SNFP. As our understanding of the N Reactor fuel performance develops the technology information supporting the SNFP will be updated and documented in later revisions to this report. Revision 1 represents the incorporation of peer review comments into the original document. The substantive evolution in our understanding of the technical status for the SNFP (except section 3) since July 1995 have not been incorporated into this revision.

  14. ISSUANCE: 2014-11-13 Energy Conservation Standards for Commercial Packaged Boilers: Public Meeting and Availability of the Preliminary Technical Support Document

    Broader source: Energy.gov [DOE]

    Energy Conservation Standards for Commercial Packaged Boilers: Public Meeting and Availability of the Preliminary Technical Support Document

  15. Technical and analytical support to the ARPA Artificial Neural Network Technology Program

    SciTech Connect (OSTI)

    NONE

    1995-09-16T23:59:59.000Z

    Strategic Analysis (SA) has provided ongoing work for the Advanced Research Projects Agency (ARPA) Artificial Neural Network (ANN) technology program. This effort provides technical and analytical support to the ARPA ANN technology program in support of the following information areas of interest: (1) Alternative approaches for application of ANN technology, hardware approaches that utilize the inherent massive parallelism of ANN technology, and novel ANN theory and modeling analyses. (2) Promising military applications for ANN technology. (3) Measures to use in judging success of ANN technology research and development. (4) Alternative strategies for ARPA involvement in ANN technology R&D. These objectives were accomplished through the development of novel information management tools, strong SA knowledge base, and effective communication with contractors, agents, and other program participants. These goals have been realized. Through enhanced tracking and coordination of research, the ANN program is healthy and recharged for future technological breakthroughs.

  16. AP1000{sup R} licensing and deployment in the United States

    SciTech Connect (OSTI)

    Jordan, R. P.; Russ, P. A.; Filiak, P. P.; Castiglione, L. L. [Westinghouse Electric Company LLC, 1000 Westinghouse Drive, Cranberry Township, PA 16066 (United States)

    2012-07-01T23:59:59.000Z

    In recent years, both domestic and foreign utilities have turned to the standardized Westinghouse AP1000 plant design in satisfying their near - and long-term - sustainable energy needs. As direct support to these actions, licensing the AP1000 design has played a significant role by providing one of the fundamental bases in clearing regulatory hurdles leading to the start of new plant construction. Within the U.S. alone, Westinghouse AP1000 licensing activities have reached unprecedented milestones with the approvals of both AP1000 Design Certification and Southern Company's combined construction permit and operating license (COL) application directly supporting the construction of two new nuclear plants in Georgia. Further COL application approvals are immediately pending for an additional two AP1000 plants in South Carolina. And, across the U.S. nuclear industry spectrum, there are 10 other COL applications under regulatory review representing some 16 new plants at 10 sites. In total, these actions represent the first wave of new plant licensing under the regulatory approval process since 1978. Fundamental to the Nuclear Regulatory Commission's AP1000 Design Certification is the formal recognition of the AP1000 passive safety design through regulatory acceptance rulemaking. Through recognition and deployment of the AP1000 Design Certification, the utility licensee / operator of this reactor design are now offered an opportunity to use a simplified 'one-step' combined license process, thereby managing substantial back-end construction schedule risk from regulatory and intervention delays. Application of this regulatory philosophy represents both acceptance and encouragement of standardized reactor designs like the AP1000. With the recent AP1000 Design Certification and utility COL acceptances, the fundamental licensing processes of this philosophy have successfully proven the attainment of significant milestones with the next stage licensing actions directed towards deployment. AP1000 Design Certification and COL deployment, and management of the plant construction in accordance with the conditions within these approvals, remain as significant site and corporate responsibilities. These licensing-construction integrated activities must now focus on identifying and resolving 'as-built' departures from the standardized design as assessed against the certified AP1000 technical and licensing basis. Within this paper, significant aspects of the AP1000 U.S. licensing will be discussed, including identifying systems and processes used in ensuring compliance while deploying the standardized design. Critical licensing steps, licensing deployment actions as plant construction progresses and defining the road forward to a successful completion of licensing actions will be addressed. (authors)

  17. License Plate 1 License Plate 2

    E-Print Network [OSTI]

    Wagner, Diane

    License Plate 1 License Plate 2 License Plate 3 License Plate 4 Single Vehicle $254 Multi Vehicle $264 ( up to 4 vehicles) Annual Decal Valid: 09/01/12 - 08/31/13 Fall /Spring Decal (Pick date range , then Single or Multi Vehicle) Multi Vehicles $200 (up to 4 vehicles) Select date range Valid 9/1/12 - 5

  18. Dose Modeling Evaluations and Technical Support Document For the Authorized Limits Request for the DOE-Owned Property Outside the Limited Area, Paducah Gaseous Diffusion Plant Paducah, Kentucky

    SciTech Connect (OSTI)

    Boerner, A. J. [Oak Ridge Institute for Science and Education (ORISE), Oak Ridge, TN (United States). Independent Environmental Assessment and Verification Program; Maldonado, D. G. [Oak Ridge Institute for Science and Education (ORISE), Oak Ridge, TN (United States). Independent Environmental Assessment and Verification Program; Hansen, Tom [Ameriphysics, LLC (United States)

    2012-09-01T23:59:59.000Z

    Environmental assessments and remediation activities are being conducted by the U.S. Department of Energy (DOE) at the Paducah Gaseous Diffusion Plant (PGDP), Paducah, Kentucky. The Oak Ridge Institute for Science and Education (ORISE), a DOE prime contractor, was contracted by the DOE Portsmouth/Paducah Project Office (DOE-PPPO) to conduct radiation dose modeling analyses and derive single radionuclide soil guidelines (soil guidelines) in support of the derivation of Authorized Limits (ALs) for 'DOE-Owned Property Outside the Limited Area' ('Property') at the PGDP. The ORISE evaluation specifically included the area identified by DOE restricted area postings (public use access restrictions) and areas licensed by DOE to the West Kentucky Wildlife Management Area (WKWMA). The licensed areas are available without restriction to the general public for a variety of (primarily) recreational uses. Relevant receptors impacting current and reasonably anticipated future use activities were evaluated. In support of soil guideline derivation, a Conceptual Site Model (CSM) was developed. The CSM listed radiation and contamination sources, release mechanisms, transport media, representative exposure pathways from residual radioactivity, and a total of three receptors (under present and future use scenarios). Plausible receptors included a Resident Farmer, Recreational User, and Wildlife Worker. single radionuclide soil guidelines (outputs specified by the software modeling code) were generated for three receptors and thirteen targeted radionuclides. These soil guidelines were based on satisfying the project dose constraints. For comparison, soil guidelines applicable to the basic radiation public dose limit of 100 mrem/yr were generated. Single radionuclide soil guidelines from the most limiting (restrictive) receptor based on a target dose constraint of 25 mrem/yr were then rounded and identified as the derived soil guidelines. An additional evaluation using the derived soil guidelines as inputs into the code was also performed to determine the maximum (peak) dose for all receptors. This report contains the technical basis in support of the DOE?s derivation of ALs for the 'Property.' A complete description of the methodology, including an assessment of the input parameters, model inputs, and results is provided in this report. This report also provides initial recommendations on applying the derived soil guidelines.

  19. Technical data summary supporting the spent nuclear fuel environment impact statement, March 1994

    SciTech Connect (OSTI)

    Geddes, R.L.; Claxton, R.E.; Lengel, J.D. [and others

    1994-03-01T23:59:59.000Z

    This report has been compiled by the WSRC Nuclear Materials Processing Division`s Planning Section at the request of the Office of Spent Fuel Management and Special Projects (EM-37) to support issuance of the Spent Nuclear Fuel Environmental Impact Statement. Savannah River Site input data evaluates five programmatic options (including {open_quotes}No Action{close_quotes}) ranging up to transfer of all DOE responsibility spent fuel to the SRS. For each option, a range of management/disposition scenarios has been examined. Each case summary provides information relative to the technical proposal, technical issues, environmental impacts, and projected costs for a forty year period (FY-35) when it is assumed that the material will be dispositioned from the SRS. The original issue of the report which was prepared under severe time constraints contained many simplifications and assumptions. Although the revisions have corrected some of the shortcomings of the original report, it is still highly recommended that significant additional study be performed before basing key decisions upon the data contained in this report. The data represents the best effort by a significant group of technical personnel familiar with nuclear materials processing, handling, and storage; but it is likely that careful scrutiny will reveal numerous discrepancies, inconsistencies and omissions. Nor does this report attempt to analyze every potential disposal pathway, but probably establishes the bounds for the most of the viable pathways. The bulk of the effort went into defining the engineering approaches necessary to execute the various mission scenarios which were changed since the last revision. The decision to limit reprocessing to only SRS aluminum clad required a major alteration of the TDS. Collection and/or calculation of much of the various waste, emission, and utility consumption data, so important to an EIS, has been updated since the last revision, but not thoroughly completed.

  20. Technical Support Document: Strategies for 50% Energy Savings in Large Office Buildings

    SciTech Connect (OSTI)

    Leach, M.; Lobato, C.; Hirsch, A.; Pless, S.; Torcellini, P.

    2010-09-01T23:59:59.000Z

    This Technical Support Document (TSD) documents technical analysis that informs design guidance for designing and constructing large office buildings that achieve 50% net site energy savings over baseline buildings defined by minimal compliance with respect to ANSI/ASHRAE/IESNA Standard 90.1-2004. This report also represents a step toward developing a methodology for using energy modeling in the design process to achieve aggressive energy savings targets. This report documents the modeling and analysis methods used to identify design recommendations for six climate zones that capture the range of U.S. climate variability; demonstrates how energy savings change between ASHRAE Standard 90.1-2007 and Standard 90.1-2004 to determine baseline energy use; uses a four-story 'low-rise' prototype to analyze the effect of building aspect ratio on energy use intensity; explores comparisons between baseline and low-energy building energy use for alternate energy metrics (net source energy, energy emissions, and energy cost); and examines the extent to which glass curtain construction limits achieve energy savings by using a 12-story 'high-rise' prototype.

  1. Technical Support Document: Development of the Advanced Energy Design Guide for Large Hospitals - 50% Energy Savings

    SciTech Connect (OSTI)

    Bonnema, E.; Leach, M.; Pless, S.

    2013-06-01T23:59:59.000Z

    This Technical Support Document describes the process and methodology for the development of the Advanced Energy Design Guide for Large Hospitals: Achieving 50% Energy Savings Toward a Net Zero Energy Building (AEDG-LH) ASHRAE et al. (2011b). The AEDG-LH is intended to provide recommendations for achieving 50% whole-building energy savings in large hospitals over levels achieved by following Standard 90.1-2004. The AEDG-LH was created for a 'standard' mid- to large-size hospital, typically at least 100,000 ft2, but the strategies apply to all sizes and classifications of new construction hospital buildings. Its primary focus is new construction, but recommendations may be applicable to facilities undergoing total renovation, and in part to many other hospital renovation, addition, remodeling, and modernization projects (including changes to one or more systems in existing buildings).

  2. Technical Support Document: The Development of the Advanced Energy Design Guide for Highway Lodging Buildings

    SciTech Connect (OSTI)

    Jiang, Wei; Jarnagin, Ronald E.; Gowri, Krishnan; McBride, M.; Liu, Bing

    2008-09-30T23:59:59.000Z

    This Technical Support Document (TSD) describes the process and methodology for development of the Advanced Energy Design Guide for Highway Lodgings (AEDG-HL or the Guide), a design guidance document intended to provide recommendations for achieving 30% energy savings in highway lodging properties over levels contained in ANSI/ASHRAE/IESNA Standard 90.1-1999, Energy Standard for Buildings Except Low-Rise Residential Buildings. The AEDG-HL is the fifth in a series of guides being developed by a partnership of organizations, including the American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc. (ASHRAE), the American Institute of Architects (AIA), the Illuminating Engineering Society of North America (IESNA), the United States Green Buildings Council (USGBC), and the U.S. Department of Energy (DOE).

  3. Support services for the Weatherization Assistance Program opportunity grants: Final technical report

    SciTech Connect (OSTI)

    Not Available

    1987-11-15T23:59:59.000Z

    The Energy-Related Business Development Project was designed by the US Department of Energy Weatherization Assistance Program (DOE/WAP) to promote activities which demonstrate strategies for providing weatherization services without Federal Funds or which promote energy-related business development activities. In December 1985, 38 community action agencies were selected through a competition grant process to participate in this demonstration project. The purpose of this project was to provide training and technical assistance to the selected grantees - to help them develop skills in business development through the identification and evaluation of potential and existing local agency energy-related ventures. This project provided support for grantees to research and package energy-related business plans capable of receiving outside financing.

  4. Technical support services to assist the Office of Environmental Audit in conducting the DOE Environmental Survey and to provide technical assistance on Environmental Compliance issues. Technical progress report, February 16, 1990--August 13, 1990

    SciTech Connect (OSTI)

    NONE

    1995-07-01T23:59:59.000Z

    NUS received authorization from DOE on August 14, 1987 to provide technical support services to assist the Office of Environmental Audit (OEV) in conducting the DOE Environmental Survey and to provide technical assistance on environmental compliance issues. The overall contract is to accomplish a one-time, no-fault baseline Survey of all DOE operating facilities, and to provide technical assistance and support for the resolution of environmental compliance issues. NUS has completed the Preliminary Reports and continues to support DOE on the Prioritization and Tiger Team Assessment efforts. The project requires a broad range of environmental protection expertise, necessitating senior-level personnel as the primary project staff. Many of the tasks assigned by DOE require quick startup and performance, and several tasks may be active at any one time.

  5. Technical Support Document: The Development of the Advanced Energy Design Guide for Small Retail Buildings

    SciTech Connect (OSTI)

    Liu, Bing; Jarnagin, Ronald E.; Winiarski, David W.; Jiang, Wei; McBride, Merle F.; Crall, C.

    2006-09-30T23:59:59.000Z

    The Advanced Energy Design Guide for Small Retail Buildings (AEDG-SR) was developed by a partnership of organizations, including the American Society of Heating, Refrigerating and Air Conditioning Engineers (ASHRAE), the American Institute of Architects (AIA), the Illuminating Engineering Society of North America (IESNA), the United States Green Buildings Council (USGBC), and the Department of Energy (DOE). The guide is intended to offer recommendations to achieve 30% energy savings and thus to encourage steady progress towards net-zero energy buildings. The baseline level energy use was set at buildings built at the turn of the millennium, which are assumed to be based on ANSI/ASHRAE/IESNA Standard 90.1-1999, Energy Standard for Buildings Except Low-Rise Residential Buildings (refer to as the ?Standard? in this report). ASHRAE and its partners are engaged in the development of a series of guides for small commercial buildings, with the AEDG-SR being the second in the series. Previously the partnership developed the Advanced Energy Design Guide for Small Office Buildings: Achieving 30% Energy Savings Over ANSI/ASHRAE/IESNA Standard 90.1-1999, which was published in late 2004. The technical support document prepared by PNNL details how the energy analysis performed in support of the Guide and documents development of recommendation criteria.

  6. Client Support: Responsible for the IT service desk, help center, technical support, divisional support and many other user support issues for CCNY community.

    E-Print Network [OSTI]

    Brinkmann, Peter

    @ccny.cuny.edu Howard Schneiderman, Sophie Davis- Network Administrator 6958 646-261-4675 howie@ccny.cuny.edu IT Service, Service Desk Manager 5828 646-631-0356 ivette@ccny.cuny.edu Patrick Flores, Administration-Tech Support Specialist 5064 917-692-9486 pflores@ccny.cuny.edu Robert Hernandez, CWE- Computer Systems Administrator 212

  7. Technical Issues Map for the NHI System Interface and Support Systems Area: 2nd Quarter FY07

    SciTech Connect (OSTI)

    Steven R. Sherman

    2007-03-01T23:59:59.000Z

    This document provides a mapping of technical issues associated with development of the Next Generation Nuclear Plant (NGNP) intermediate heat transport loop and nuclear hydrogen plant support systems to the work that has been accomplished or is currently underway in the 2nd quarter of FY07.

  8. Impact assessment of draft DOE Order 5820.2B. Radioactive Waste Technical Support Program

    SciTech Connect (OSTI)

    NONE

    1995-04-01T23:59:59.000Z

    The Department of Energy (DOE) has prepared a revision to DOE Order 5820.2A, entitled ``Radioactive Waste Management.`` DOE issued DOE Order 5820.2A in September 1988 and, as the title implies, it covered only radioactive waste forms. The proposed draft order, entitled ``Waste Management,`` addresses the management of both radioactive and nonradioactive waste forms. It also includes spent nuclear fuel, which DOE does not consider a waste. Waste forms covered include hazardous waste, high-level waste, transuranic (TRU) waste, low-level radioactive waste, uranium and thorium mill tailings, mixed waste, and sanitary waste. The Radioactive Waste Technical Support Program (TSP) of Leached Idaho Technologies Company (LITCO) is facilitating the revision of this order. The EM Regulatory Compliance Division (EM-331) has requested that TSP estimate the impacts and costs of compliance with the revised order. TSP requested Dames & Moore to aid in this assessment by comparing requirements in Draft Order 5820.2B to ones in DOE Order 5820.2A and other DOE orders and Federal regulations. The assessment started with a draft version of 5820.2B dated January 14, 1994. DOE has released three updated versions of the draft order since then (dated May 20, 1994; August 26, 1994; and January 23, 1995). Each time DOE revised the order, Dames and Moore updated the assessment work to reflect the text changes. This report reflects the January 23, 1995 version of the draft order.

  9. GPHS-RTGs in support of the Cassini Mission. Semi annual technical report, 30 September 1996--30 March 1997

    SciTech Connect (OSTI)

    NONE

    1997-04-20T23:59:59.000Z

    The technical progress achieved during the period 27 January through 30 September 1996 through 30 March 1997 on Contract DE-AC03-91SF18852 Radioisotope Thermoelectric Generators and Ancillary Activities is described. This report is organized by program task structure: spacecraft integration and liaison; engineering support; safety; qualified unicouple production; ETG fabrication, assembly, and test; ground support equipment (GSE); RTG shipping and launch support; designs, reviews, and mission applications; project management, quality assurance, reliability, contract changes, CAGO acquisition (operating funds), and CAGO maintenance and repair; and CAGO acquisition (capital funds).

  10. Technical support services to assist the Office of Environmental Audit in conducting the DOE Environmental Survey and to provide technical assistance on Environmental Compliance issues. Technical progress report, August 14, 1990--February 15, 1991

    SciTech Connect (OSTI)

    NONE

    1995-07-01T23:59:59.000Z

    NUS received authorization from DOE on August 14, 1987 to provide technical support services to assist the Office of Environmental Audit (OEV) in conducting the DOE Environmental Survey and to provide technical assistance on environmental compliance issues. The overall contract is to accomplish a one-time, no-fault baseline Survey of all DOE operating facilities, and to provide technical assistance and support for the resolution of environmental compliance issues. NUS has completed the Preliminary Reports and continues to support DOE on the Prioritization and Tiger Team Assessment efforts. The project requires a broad range of environmental protection expertise, necessitating senior-level personnel as the primary project staff. Many of the tasks assigned by DOE require quick startup and performance, and several tasks may be active at any one time. The objective of the DOE Environmental Survey Program is to identify and prioritize areas of existing environmental risk at 36 DOE facilities. NUS`role is to technically assist the Office of Environmental Audit in the implementation of the Surveys.

  11. Technical Support Document: Development of the Advanced Energy Design Guide for Small Office Buildings

    SciTech Connect (OSTI)

    Jarnagin, Ronald E.; Liu, Bing; Winiarski, David W.; McBride, Merle F.; Suharli, L.; Walden, D.

    2006-11-30T23:59:59.000Z

    This Technical Support Document (TSD) describes the process and methodology for the development of the Advanced Energy Design Guide for Small Office Buildings (AEDG-SO), a design guidance document intended to provide recommendations for achieving 30% energy savings in small office buildings over levels contained in ANSI/ASHRAE/IESNA Standard 90.1-1999, Energy Standard for Buildings Except Low-Rise Residential Buildings. The AEDG-SO is the first in a series of guides being developed by a partnership of organizations, including the American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc. (ASHRAE), the American Institute of Architects (AIA), the Illuminating Engineering Society of North America (IESNA), the New Buildings Institute (NBI), and the U.S. Department of Energy (DOE). Each of the guides in the AEDG series will provide recommendations and user-friendly design assistance to designers, developers and owners of small commercial buildings that will encourage steady progress towards net-zero energy buildings. The guides will provide prescriptive recommendation packages that are capable of reaching the energy savings target for each climate zone in order to ease the burden of the design and construction of energy-efficient small commercial buildings The AEDG-SO was developed by an ASHRAE Special Project committee (SP-102) made up of representatives of each of the partner organizations in eight months. This TSD describes the charge given to the committee in developing the office guide and outlines the schedule of the development effort. The project committee developed two prototype office buildings (5,000 ft2 frame building and 20,000 ft2 two-story mass building) to represent the class of small office buildings and performed an energy simulation scoping study to determine the preliminary levels of efficiency necessary to meet the energy savings target. The simulation approach used by the project committee is documented in this TSD along with the characteristics of the prototype buildings. The prototype buildings were simulated in the same climate zones used by the prevailing energy codes and standards to evaluate energy savings. Prescriptive packages of recommendations presented in the guide by climate zone include enhanced envelope technologies, lighting and day lighting technologies and HVAC and SWH technologies. The report also documents the modeling assumptions used in the simulations for both the baseline and advanced buildings. Final efficiency recommendations for each climate zone are included, along with the results of the energy simulations indicating an average energy savings over all buildings and climates of approximately 38%.

  12. Determination for the 2006 International Energy Conservation Code, Residential Buildings – Technical Support Document

    SciTech Connect (OSTI)

    Lucas, Robert G.

    2009-09-26T23:59:59.000Z

    Provides a technical analysis showing that the 2006 International Energy Conservation Code contains improvements in energy efficiency compared to its predecessor, the 2003 International Energy Conservation Code. DOE is required by law to issue "determinations" of whether or not new editions of the IECC improve energy efficiency.

  13. Technical support document for the proposed Federal Commercial Building energy code

    SciTech Connect (OSTI)

    Somasundaram, S.; Halverson, M.A.; Jones, C.C.; Hadley, D.L.

    1995-11-01T23:59:59.000Z

    This report presents the justification and technical documentation for all changes and updates made (since 1993) to the Energy Code for Commercial and High-Rise Residential Buildings, the codified version of ASHRAE/IES Standard 90.1-1989, ``Energy Efficient Design of New Buildings Except Low-Rise Residential Buildings.`` These changes and updates, which were subject to the ASHRAE addenda approval process, include Addenda b, c, d, e, g, and i. A seventh addenda, Addenda f, which has not been officially approved by ASHRAE, has been included into the proposed rule. Also included in the changes was technical work conducted to justify revisions to the 1993 DOE lighting power densities. The updated text will be reviewed by the U.S. Department of Energy (DOE) and issued as the new Federal Commercial Building Energy Code (10 CFR 434); Mandatory for New Federal Commercial and Multi-Family High Rise Residential Buildings.

  14. ANL Technical Support Program for DOE Environmental Restoration and Waste Management; Annual report, October 1992--September 1993

    SciTech Connect (OSTI)

    Bates, J.K.; Bourcier, W.L.; Bradley, C.R. [and others

    1994-06-01T23:59:59.000Z

    This report is an overview of the progress during FY 1993 for the Technical Support Program that is part of the ANL Technology Support Activity for DOE Environmental Restoration and Waste Management (EM). The purpose is to evaluate, before hot start-up of the Defense Waste Processing Facility (DWPF) and the West Valley Demonstration Project (WVDP), factors that are anticipated to affect glass reaction in an unsaturated environment typical of what may be expected for the candidate Yucca Mountain repository site. Specific goals for the testing program include the following: reviewing and evaluating available data on parameters that will be important in establishing the long-term performance of glass in a repository environment; performing tests to further quantify the effects of important variables where there are deficiencies in the available data; and initiating long-term tests to determine glass performance under a range of conditions applicable to repository disposal.

  15. Licensing plan for UMTRA project disposal sites. Final [report

    SciTech Connect (OSTI)

    Not Available

    1993-09-01T23:59:59.000Z

    The Uranium Mill Tailings Remedial Action (UMTRA) Project Office developed a plan to define UMTRA Project licensing program objectives and establish a process enabling the DOE to document completion of remedial actions in compliance with 40 CFR 1 92 and the requirements of the NRC general license. This document supersedes the January 1987 Project Licensing Plan (DOE, 1987). The plan summarizes the legislative and regulatory basis for licensing, identifies participating agencies and their roles and responsibilities, defines key activities and milestones in the licensing process, and details the coordination of these activities. This plan provides an overview of the UMTRA Project from the end of remedial actions through the NRC`s acceptance of a disposal site under the general license. The licensing process integrates large phases of the UMTRA Project. Other programmatic UMTRA Project documents listed in Section 6.0 provide supporting information.

  16. Engineering support services for the DOE/GRI coal gasification research program. Final technical progress report, October 1978-November 1982

    SciTech Connect (OSTI)

    Bostwick, L.E.

    1982-01-01T23:59:59.000Z

    The agreement between the United States Government Department of Energy and the Gas Research Institute for the Joint Coal Gasification Research Program provided for one or more technical evaluation contractors. Pullman Kellogg (now the M.W. Kellogg Company) was selected as evaluation contractor to assess, and report to the DOE/GRI Operating Committee on, the relative merits of the active programs covered by the agreement. This report includes the period from 1 October 1978 to 30 November 1982. The objective was to provide engineering support for the DOE/GRI high Btu coal gasification program. This support generally consisted of assistance in developing or advancing each process to its maximum potential. Kellogg monitored and evaluated the startup and operational activities of all pilot plant projects within the combined DOE/GRI program. Kellogg evaluated proposals to determine their technical feasibility as potential processes or as viable processing operations for commercial-scale gasification of coal. Kellogg also recorded observations on the reliability, maintainability, and availability of the equipment used in the pilot plant or PDU facilities. Kellogg performed design reviews, data analyses, and engineering evaluations of proposals, cost estimates and monthly progress reports to provide information considered essential to the overall objectives of the combined DOE/GRI program.

  17. DOE TRANSCOM Technical Support Service DE-EM0002903 G-1 PART I - THE SCHEDULE

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power Administration wouldDECOMPOSITION OF CALCIUMCOSTDOE Solar Training andDOE TRANSCOM Technical

  18. Technical Support Document for the National Environmental Policy Act Implementing Procedures

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn'tOriginEducationVideoStrategic| Department ofGeneralWindBuildingOffice28-98 - May2012 |Technical

  19. Sustainability Support

    Broader source: Energy.gov [DOE]

    Sustainability Support serves as a corporate technical assistance, coordination, and integration resource to support line organizations in the resolution of sustainability issues and management concerns.

  20. Licensing | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    (TDC) Division negotiates and manages license agreements on behalf of UChicago Argonne, LLC, which operates Argonne National Laboratory for the U.S. Department of Energy....

  1. Management support services to the Office of Utility Technologies. Final technical report

    SciTech Connect (OSTI)

    Not Available

    1993-12-16T23:59:59.000Z

    The Office of Utility Technologies works cooperatively with industry and the utility sector to realize the market potential for energy efficiency and renewable energy technologies. Under this contract, BNF has provided management support services for OUT R&D activities for the following Program offices: (1) Office of Energy Management; (2) Office of Solar Energy Conversion; (3) Office of Renewable Energy Conversion; and (4) Deputy Assistant Secretary. During the period between 4/17/91 and 9/17/93, BNF furnished the necessary personnel, equipment, materials, facilities and travel required to provide management support services for each of the above Program Offices. From 9/18/93 to 12/17/93, BNF has been involved in closeout activities, including final product deliverables. Research efforts that have been supported in these Program Offices are: (1) for Energy Management -- Advanced Utility Concepts Division; Utility Systems Division; Integrated Planning; (2) for Solar Energy Conversion -- Photovoltaics Division; Solar Thermal and Biomass Power Division; (3) for Renewable Energy Conversion -- Geothermal Division; Wind, Hydroelectric and Ocean Systems Division; (4) for the Deputy Assistant Secretary -- support as required by the Supporting Staff. This final report contains summaries of the work accomplished for each of the Program Offices listed above.

  2. Radioactive Materials License Commitments

    E-Print Network [OSTI]

    Radioactive Materials License Commitments for The University of Texas at Austin May 2009 July 2009 in the use of radioactive materials. In July 1963, the State of Texas granted The University of Texas at Austin a broad radioactive materials license for research, development and instruction. While this means

  3. Technical Support Document: Development of the Advanced Energy Design Guide for Medium to Big Box Retail Buildings - 50% Energy Savings

    SciTech Connect (OSTI)

    Bonnema, E.; Leach, M.; Pless, S.

    2013-06-01T23:59:59.000Z

    This Technical Support Document describes the process and methodology for the development of the Advanced Energy Design Guide for Medium to Big Box Retail Buildings: Achieving 50% Energy Savings Toward a Net Zero Energy Building (AEDG-MBBR) ASHRAE et al. (2011b). The AEDG-MBBR is intended to provide recommendations for achieving 50% whole-building energy savings in retail stores over levels achieved by following ANSI/ASHRAE/IESNA Standard 90.1-2004, Energy Standard for Buildings Except Low-Rise Residential Buildings (Standard 90.1-2004) (ASHRAE 2004b). The AEDG-MBBR was developed in collaboration with the American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE), the American Institute of Architects (AIA), the Illuminating Engineering Society of North America (IES), the U.S. Green Building Council (USGBC), and the U.S. Department of Energy.

  4. Technical support document: Survey data used in revising the energy conservation requirements in the manufactured home construction and safety standards

    SciTech Connect (OSTI)

    Lee, A.D.; Conner, C.C.

    1992-02-01T23:59:59.000Z

    This report documents data used in the development of revised energy conservation standards for manufactured housing. The approach used in developing the proposed standard revision is a cost-benefit analysis in which the costs of energy conservation measures (ECM) are balanced against the benefits of energy savings. The analysis used to develop the recommendations for revision of the US Department of Housing and Urban Development (HUD) energy conservation standards for manufactured housing requires information on specific ECMs. This technical support document contains the data from two of the three surveys that were used primarily to characterize the available ECMs and their associated costs. The analyses of these data are provided in separate reports. 5 refs.

  5. Cost-Effectiveness Analysis of the 2009 and 2012 IECC Residential Provisions – Technical Support Document

    SciTech Connect (OSTI)

    Mendon, Vrushali V.; Lucas, Robert G.; Goel, Supriya

    2012-12-04T23:59:59.000Z

    This analysis was conducted by Pacific Northwest National Laboratory (PNNL) in support of the U.S. Department of Energy’s (DOE) Building Energy Codes Program (BECP). DOE supports the development and adoption of efficient residential and commercial building energy codes. These codes set the minimum requirements for energy efficient building design and construction and ensure energy savings on a national level. This analysis focuses on one and two family dwellings, townhomes, and low-rise multifamily residential buildings. For these buildings, the basis of the energy codes is the International Energy Conservation Code (IECC). This report does not address commercial and high-rise residential buildings, which reference ANSI/ASHRAE/IES Standard 90.1.

  6. DOE Awards Small Business Task Order for Technical Support to the Office of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE: Alternative FuelsNovember 13, 2014Contributing DataDepartmentGuideandandBestSupport

  7. Data development technical support document for the aircraft crash risk analysis methodology (ACRAM) standard

    SciTech Connect (OSTI)

    Kimura, C.Y.; Glaser, R.E.; Mensing, R.W.; Lin, T.; Haley, T.A.; Barto, A.B.; Stutzke, M.A.

    1996-08-01T23:59:59.000Z

    The Aircraft Crash Risk Analysis Methodology (ACRAM) Panel has been formed by the US Department of Energy Office of Defense Programs (DOE/DP) for the purpose of developing a standard methodology for determining the risk from aircraft crashes onto DOE ground facilities. In order to accomplish this goal, the ACRAM panel has been divided into four teams, the data development team, the model evaluation team, the structural analysis team, and the consequence team. Each team, consisting of at least one member of the ACRAM plus additional DOE and DOE contractor personnel, specializes in the development of the methodology assigned to that team. This report documents the work performed by the data development team and provides the technical basis for the data used by the ACRAM Standard for determining the aircraft crash frequency. This report should be used to provide the generic data needed to calculate the aircraft crash frequency into the facility under consideration as part of the process for determining the aircraft crash risk to ground facilities as given by the DOE Standard Aircraft Crash Risk Assessment Methodology (ACRAM). Some broad guidance is presented on how to obtain the needed site-specific and facility specific data but this data is not provided by this document.

  8. Issuance 2014-11-21:Energy Efficiency Program for Consumer Products: Energy Conservation Standards for Ceiling Fans: Availability of the Preliminary Technical Support Document, Notice of Comment Period Extension

    Broader source: Energy.gov [DOE]

    Energy Efficiency Program for Consumer Products: Energy Conservation Standards for Ceiling Fans: Availability of the Preliminary Technical Support Document, Notice of Comment Period Extension

  9. Microsoft PowerPoint - Nuclear Material Import Export License...

    National Nuclear Security Administration (NNSA)

    Commission (NRC) importexport license? - Licenses for imports - Licenses for exports - Export license monitoring Highlights of importsexports in 2014 - Nuclear...

  10. NEXT GENERATION NUCLEAR PLANT LICENSING BASIS EVENT SELECTION WHITE PAPER

    SciTech Connect (OSTI)

    Mark Holbrook

    2010-09-01T23:59:59.000Z

    The Next Generation Nuclear Plant (NGNP) will be a licensed commercial high temperature gas-cooled reactor (HTGR) plant capable of producing the electricity and high temperature process heat for industrial markets supporting a range of end-user applications. The NGNP Project has adopted the 10 CFR 52 Combined License (COL) application process, as recommended in the Report to Congress, dated August 2008, as the foundation for the NGNP licensing strategy. NRC licensing of the NGNP plant utilizing this process will demonstrate the efficacy of licensing future HTGRs for commercial industrial applications. This white paper is one in a series of submittals that will address key generic issues of the COL priority licensing topics as part of the process for establishing HTGR regulatory requirements.

  11. PNNL Technical Support to The Implementation of EMTA and EMTA-NLA Models in Autodesk® Moldflow® Packages

    SciTech Connect (OSTI)

    Nguyen, Ba Nghiep; Wang, Jin

    2012-12-01T23:59:59.000Z

    Under the Predictive Engineering effort, PNNL developed linear and nonlinear property prediction models for long-fiber thermoplastics (LFTs). These models were implemented in PNNL’s EMTA and EMTA-NLA codes. While EMTA is a standalone software for the computation of the composites thermoelastic properties, EMTA-NLA presents a series of nonlinear models implemented in ABAQUS® via user subroutines for structural analyses. In all these models, it is assumed that the fibers are linear elastic while the matrix material can exhibit a linear or typical nonlinear behavior depending on the loading prescribed to the composite. The key idea is to model the constitutive behavior of the matrix material and then to use an Eshelby-Mori-Tanaka approach (EMTA) combined with numerical techniques for fiber length and orientation distributions to determine the behavior of the as-formed composite. The basic property prediction models of EMTA and EMTA-NLA have been subject for implementation in the Autodesk® Moldflow® software packages. These models are the elastic stiffness model accounting for fiber length and orientation distributions, the fiber/matrix interface debonding model, and the elastic-plastic models. The PNNL elastic-plastic models for LFTs describes the composite nonlinear stress-strain response up to failure by an elastic-plastic formulation associated with either a micromechanical criterion to predict failure or a continuum damage mechanics formulation coupling damage to plasticity. All the models account for fiber length and orientation distributions as well as fiber/matrix debonding that can occur at any stage of loading. In an effort to transfer the technologies developed under the Predictive Engineering project to the American automotive and plastics industries, PNNL has obtained the approval of the DOE Office of Vehicle Technologies to provide Autodesk, Inc. with the technical support for the implementation of the basic property prediction models of EMTA and EMTA-NLA in the Autodesk® Moldflow® packages. This report summarizes the recent results from Autodesk Simulation Moldlow Insight (ASMI) analyses using the EMTA models and EMTA-NLA/ABAQUS® analyses for further assessment of the EMTA-NLA models to support their implementation in Autodesk Moldflow Structural Alliance (AMSA). PNNL’s technical support to Autodesk, Inc. included (i) providing the theoretical property prediction models as described in published journal articles and reports, (ii) providing explanations of these models and computational procedure, (iii) providing the necessary LFT data for process simulations and property predictions, and (iv) performing ABAQUS/EMTA-NLA analyses to further assess and illustrate the models for selected LFT materials.

  12. Technical support to the Solvent Refined Coal (SRC) demonstration projects: assessment of current research and development

    SciTech Connect (OSTI)

    Edwards, M.S.; Rodgers, B.R.; Brown, C.H.; Carlson, P.K.; Gambill, W.R.; Gilliam, T.M.; Holmes, J.M.; Krishnan, R.P.; Parsly, L.F.

    1980-12-01T23:59:59.000Z

    A program to demonstrate Solvent Refined Coal (SRC) technology has been initiated by the US Department of Energy (DOE) in partnership with two industrial groups. Project management responsibility has been assigned to the Oak Ridge Operations Office (ORO) of DOE. ORO requested that the Oak Ridge National Laboratory assess current research and development (R and D) activities and develop recommendations for those activities that might contribute to successful completion of the SRC demonstration plant projects. The objectives of this final report are to discuss in detail the problem areas in SRC; to discuss the current and planned R and D investigations relevant to the problems identified; and to suggest appropriate R and D activities in support of designs for the SRC demonstration plants. Four types of R and D activities are suggested: continuation of present and planned activities; coordination of activities and results, present and proposed; extension/redirection of activities not involving major equipment purchase or modifications; and new activities. Important examples of the first type of activity include continuation of fired heater, slurry rheology, and slurry mixing studies at Ft. Lewis. Among the second type of activity, coordination of data acquisition and interpretation is recommended in the areas of heat transfer, vapor/liquid equilibria, and physical properties. Principal examples of recommendations for extension/redirection include screening studies at laboratory scale on the use of carbonaceous precoat (e.g., anthracite) infiltration, and 15- to 30-day continuous tests of the Texaco gasifier at the Texaco Montebello facility (using SRC residues).

  13. Final Technical Report: Supporting Wind Turbine Research and Testing - Gearbox Durability Study

    SciTech Connect (OSTI)

    Matthew Malkin

    2012-04-30T23:59:59.000Z

    The combination of premature failure of wind turbine gearboxes and the downtime caused by those failures leads to an increase in the cost of electricity produced by the wind. There is a need for guidance to asset managers regarding how to maximize the longevity of their gearboxes in order to help keep the cost of wind energy as low as possible. A low cost of energy supports the US Department of Energy's goal of achieving 20% of the electricity in the United States produced by wind by the year 2030. DNV KEMA has leveraged our unique position in the industry as an independent third party engineering organization to study the problem of gearbox health management and develop guidance to project operators. This report describes the study. The study was conducted in four tasks. In Task 1, data that may be related to gearbox health and are normally available to wind project operators were collected for analysis. Task 2 took a more in-depth look at a small number of gearboxes to gain insight in to relevant failure modes. Task 3 brought together the previous tasks by evaluating the available data in an effort to identify data that could provide early indications of impending gearbox failure. Last, the observations from the work were collected to develop recommendations regarding gearbox health management.

  14. Game-based dynamic simulations supporting technical education and training iJOE International Journal of Online Engineering -www.i-joe.org 1

    E-Print Network [OSTI]

    Foss, Bjarne A.

    . SIMULATIONS AND GAMES FOR LEARNING PURPOSES The development of ICT solutions has allowed for more complex and advanced representations of learning material. In this context, dynamic simulators can be regardedGame-based dynamic simulations supporting technical education and training iJOE International

  15. Licensing East Asian Resources

    E-Print Network [OSTI]

    Chu, Victoria; Eggleston, Holly

    2008-01-01T23:59:59.000Z

    our licensing of East Asian Resources here at UCSD. y It isthe history of electronic resources and the use of licensesclick through, or even use a resource with posted terms on a

  16. Decision making technical support study for the US Army's Chemical Stockpile Disposal Program

    SciTech Connect (OSTI)

    Feldman, D.L.; Dobson, J.E.

    1990-08-01T23:59:59.000Z

    This report examines the adequacy of current command and control systems designed to make timely decisions that would enable sufficient warning and protective response to an accident at the Edgewood area of Aberdeen Proving Ground (APG), Maryland, and at Pine Bluff Arsenal (PBA), Arkansas. Institutional procedures designed to facilitate rapid accident assessment, characterization, warning, notification, and response after the onset of an emergency and computer-assisted decision-making aids designed to provide salient information to on- and-off-post emergency responders are examined. The character of emergency decision making at APG and PBA, as well as potential needs for improvements to decision-making practices, procedures, and automated decision-support systems (ADSSs), are described and recommendations are offered to guide equipment acquisition and improve on- and off-post command and control relationships. We recommend that (1) a continued effort be made to integrate on- and off-post command control, and decision-making procedures to permit rapid decision making; (2) the pathways for alert and notification among on- and off-post officials be improved and that responsibilities and chain of command among off-post agencies be clarified; (3) greater attention be given to organizational and social context factors that affect the adequacy of response and the likelihood that decision-making systems will work as intended; and (4) faster improvements be made to on-post ADSSs being developed at APG and PBA, which hold considerable promise for depicting vast amounts of information. Phased development and procurement of computer-assisted decision-making tools should be undertaken to balance immediate needs against available resources and to ensure flexibility, equity among sites, and compatibility among on- and off-post systems. 112 refs., 6 tabs.

  17. Our primary technical problem was to support the U.S. Department of Energy (DOE) in modernizing its management

    E-Print Network [OSTI]

    Kemner, Ken

    laboratory system. K-AREA MATERIAL STORAGE (KAMS) FACILITY AT THE DOE SAVANNAH RIVER SITE, AIKEN, SC At KAMS's "Most Innovative Use of RFID" Award in 2011. Results Commercialization In July 2012, Argonne National Laboratory and Evigia Systems, Inc. (Ann Arbor, Michigan; www.evigia.com), reached a licensing agreement

  18. GPHS-RTGs in support of the Cassini Mission. Semi annual technical progress report, 1 April 1996--29 September 1996

    SciTech Connect (OSTI)

    NONE

    1996-10-20T23:59:59.000Z

    This technical progress report discusses work on the Radioisotope Generators and Ancillary Activities for the Cassini spacecraft. The Cassini spacecraft is expected to launch in October 1997, and will explore Saturn and its moons. This progress report discusses issues in: spacecraft integration and liason, engineering support, safety, qualified unicouple fabrication, ETG fabrication and testing, ground support equipment, RTG shipping and launch support, designs, reviews and mission application. Safety analysis of the RTGs during reentry and launch accidents are covered. This report covers the period of April 1 to September 29, 1996.

  19. Academic Information Technical Support

    E-Print Network [OSTI]

    Hickman, Mark

    & expensive) #12;Sedimentology&Palaeontology Chris Grimshaw · In charge of Palynology lab, sediment preparation, fossil collections entomology preparation and project room areas. · In sedimentology we provide

  20. Guidance document for revision of DOE Order 5820.2A, Radioactive Waste Technical Support Program. Revision 1

    SciTech Connect (OSTI)

    Kudera, D.E.; McMurtrey, C.D.; Meagher, B.G.

    1993-04-01T23:59:59.000Z

    This document provides guidance for the revision of DOE Order 5820.2A, ``Radioactive Waste Management.`` Technical Working Groups have been established and are responsible for writing the revised order. The Technical Working Groups will use this document as a reference for polices and procedures that have been established for the revision process. The overall intent of this guidance is to outline how the order will be revised and how the revision process will be managed. In addition, this document outlines technical issues considered for inclusion by a Department of Energy Steering Committee.

  1. License Iso. CM35

    Office of Legacy Management (LM)

    License Iso. CM35 hUhUll4MhiM&POlltYll7 llolh-thRqalStract Alolan&le, vlrghla Attoatlonl w. & 0. EutahlDon Pursuant to the Atanic Energy Act of 1954 and Section 40.21 or the Code...

  2. License Application Design Selection Report, REV 01. August 1999

    SciTech Connect (OSTI)

    Hastings, C.R.

    1999-08-30T23:59:59.000Z

    In December 1998, the U.S. Department of Energy (DOE) published the ''Viability Assessment of a Repository at Yucca Mountain'' (DOE 1998b). The Viability Assessment described a preliminary design of a potential repository at Yucca Mountain, Nevada, for disposal of spent nuclear fuel and high-level radioactive waste, and assessed the probable behavior of that repository design in the Yucca Mountain geologic setting. The report concluded that 'Yucca Mountain remains a promising site for a geologic repository and that work should proceed to support a decision in 2001 on whether to recommend the site to the President for development as a repository'. It also concluded that 'uncertainties remain about key natural processes, the preliminary design, and how the site and design would interact'. Recognizing that the design that was evaluated will be refined before a license application could be submitted, the Viability Aassesment notes that 'DOE is evaluating several design options and alternatives that could reduce existing uncertainty and improve the performance of the repository system'. During the preparation of the Viability Assessment, DOE asked the contractor for the Civilian Radioactive Waste Management Program to study alternative design concepts for a potential geologic repository for high-level radioactive waste at Yucca Mountain. The License Application Design Selection (LADS) project was initiated to conduct that study. The goal of the project was to develop and evaluate a diverse range of conceptual repository designs that work well in concert with the Yucca Mountain site and to recommend an initial design concept for the possible Site Recommendation and License Apllication. This report presents the results of the LADS project. The design process consisted of two phases. In Phase I, a series of basic design concepts (design alternatives) and components (design features) were analyzed for their potential value as elements of a repository design. In Phase II, these enhanced design alternatives were refined, screened for accepatable postclosure performance, and evaluated against a set of criteria addressing four broad aspects of the repository: performance demonstrability; flexibility; construction, operations and maintenance; and cost. Based on this evaluation, a conceptual design was recommended to DOE and could be characterized as a low thermal impact design. Included in the report is more in depth information regarding the basis of the recommendation, performance issues, benefits related to reduced uncertainties, construction/operational benefits, technical and programmatic flexibilty and cost impacts.

  3. Kentucky Water Resources Research Institute Annual Technical Report

    E-Print Network [OSTI]

    support for the Paducah Gaseous Diffusion Plant (CHS), 3) Technical Support for Environmental Construction

  4. Technical Fact Sheets

    Broader source: Energy.gov [DOE]

    Technical Fact Sheets (TFS) provide summary-level information on the impact of new, deployed, applied, and/or planned technical approaches supporting EM cleanup projects.  The TFS is presented as a...

  5. Dose Modeling Evaluations and Technical Support Document for the Authorized Limits Request for the C-746-U Landfill at the Paducah Gaseous Diffusion Plant, Paducah, Kentucky

    SciTech Connect (OSTI)

    Boerner, A. J. [IEAVP, ORISE, Oak Ridge, TN (United States); Maldonado, D. G. [IEAVP, ORISE, Oak Ridge, TN (United States; Hansen, Tom [Ameriphysics, LLC (United States)

    2012-06-01T23:59:59.000Z

    This report contains the technical basis in support of the DOE?s derivation of Authorized Limits (ALs) for the DOE Paducah C-746-U Landfill. A complete description of the methodology, including an assessment of the input parameters, model inputs, and results is provided in this report. This report also provides initial recommendations on applying the derived soil guidelines. The ORISE-derived soil guidelines are specifically applicable to the Landfill at the end of its operational life. A suggested 'upper bound' multiple of the derived soil guidelines for individual shipments is provided.

  6. 2014-10-27 Issuance: Energy Conservation Standards for Ceiling Fan Light Kits; Notice of Public Meeting and Availability of the Preliminary Technical Support Document

    Broader source: Energy.gov [DOE]

    This document is a pre-publication Federal Register notice of public meeting and availability of the preliminary technical support document regarding energy conservation standards for ceiling fan light kits, as issued by the Deputy Assistant Secretary for Energy Efficiency on October 27, 2014. Though it is not intended or expected, should any discrepancy occur between the document posted here and the document published in the Federal Register, the Federal Register publication controls. This document is being made available through the Internet solely as a means to facilitate the public's access to this document.

  7. 2014-09-16 Issuance: Energy Conservation Standards for Ceiling Fans; Notice of Public Meeting and Availability of Preliminary Technical Support Document

    Broader source: Energy.gov [DOE]

    This document is a pre-publication Federal Register notice of public meeting and availability of preliminary technical support document regarding energy conservation standards for ceiling fans, as issued by the Deputy Assistant Secretary on September 16, 2014. Though it is not intended or expected, should any discrepancy occur between the document posted here and the document published in the Federal Register, the Federal Register publication controls. This document is being made available through the Internet solely as a means to facilitate the public's access to this document.

  8. 2014-08-01 Issuance: Energy Conservation Standard for Refrigerated Bottled or Canned Beverage Vending Machines; Notice of Public Meeting and Availability of the Preliminary Technical Support Document

    Broader source: Energy.gov [DOE]

    This document is a pre-publication Federal Register notice of public meeting and availability of the preliminary technical support document for refrigerated bottled or canned beverage vending machines, as issued by the Deputy Assistant Secretary for Energy Efficiency on August 1, 2014. Though it is not intended or expected, should any discrepancy occur between the document posted here and the document published in the Federal Register, the Federal Register publication controls. This document is being made available through the Internet solely as a means to facilitate the public's access to this document.

  9. 2014-11-25 Issuance: Energy Conservation Standards for Miscellaneous Refrigeration Products; Notice of Open Meeting and Availability of the Preliminary Technical Support Document

    Broader source: Energy.gov [DOE]

    This document is a pre-publication Federal Register notice of open meeting and availability of the preliminary technical support document regarding energy conservation standards for miscellaneous refrigeration products, as issued by the Deputy Assistant Secretary for Energy Efficiency on November 25, 2014. Though it is not intended or expected, should any discrepancy occur between the document posted here and the document published in the Federal Register, the Federal Register publication controls. This document is being made available through the Internet solely as a means to facilitate the public's access to this document.

  10. GPHS-RTGs in support of the Cassini Mission. Semiannual technical progress report, 27 September 1993--27 March 1994

    SciTech Connect (OSTI)

    Not Available

    1994-04-24T23:59:59.000Z

    This report is organized by the program task structure as follows: (1) spacecraft integration and liaison; (2) engineering support; (3) safety; (4) qualified unicouple fabrication; (5) ETG fabrication, assembly, and test; (6) ground support equipment (GSE); (7) RTG shipping and launch support; (8) designs, reviews, and mission applications; (9) project management, quality assurance and reliability, contract changes, non-capital CAGO acquisition, and CAGO maintenance; and (H) contractor acquired government owned property (CAGO) acquisition.

  11. NRC antitrust licensing actions, 1978--1996

    SciTech Connect (OSTI)

    Mayer, S.J.; Simpson, J.J.

    1997-09-01T23:59:59.000Z

    NUREG-0447, Antitrust Review of Nuclear Power Plants, was published in May 1978 and includes a compilation and discussion of U.S. Nuclear Regulatory Commission (NRC) proceedings and activity involving the NRC`s competitive review program through February 1978, NUREG-0447 is an update of an earlier discussion of the NRC`s antitrust review of nuclear power plants, NR-AIG-001, The US Nuclear Regulatory Commission`s Antitrust Review of Nuclear Power Plants: The Conditioning of Licenses, which reviewed the Commission`s antitrust review function from its inception in December 1970 through April 1976. This report summarizes the support provided to NRC staff in updating the compilation of the NRC`s antitrust licensing review activities for commercial nuclear power plants that have occurred since February 1978. 4 refs., 4 tabs.

  12. International LicensingInternational Licensing and Intellectualand Intellectual

    E-Print Network [OSTI]

    Lansky, Joshua

    " to license:"incentives" to license: Economic Returns EffectEconomic Returns Effect - reduction in risk("Developed country members shall provide incentives . . . for the purpose of . . .shall provide incentives incentives to marketIncrease incentives to market technologiestechnologies #12;In principle, IPRs can have

  13. Final Report. SFAA No. DEFC02-98CH10961. Technical assistance for joint implementation and other supporting mechanisms and measures for greenhouse gas emissions mitigation

    SciTech Connect (OSTI)

    Knight, Denise

    2001-10-15T23:59:59.000Z

    IIEC, a division of CERF, has developed an extensive base of experience implementing activities that support climate action by developing USIJI projects in transitional countries within Asia, Latin America, Central and Eastern Europe, and southern Africa. IIEC has been able to provide a range of technical and policy assistance to governments and industry in support of sustainable energy use. IIEC continues to work in key countries with local partners to develop and implement energy efficiency policies and standards, develop site-specific projects, and assist governing bodies to establish national priorities and evaluation criteria for approving GHG-mitigation projects. As part of this project, IIEC focused on promoting a series of activities in Thailand and South Africa in order to identify GHG mitigation projects and work within the national approval process of those countries. The sections of this report outline the activities conducted in each country in order to achieve that goal.

  14. TECHNICAL COMPARISON OF CANDIDATE ION EXCHANGE MEDIA FOR SMALL COLUMN ION EXCHANGE (SCIX) APPLICATIONS IN SUPPORT OF SUPPLEMENTAL LAW PRETREATMENT

    SciTech Connect (OSTI)

    RAMSEY AA; THORSON MR

    2010-12-28T23:59:59.000Z

    At-tank supplemental pretreatment including both filtration and small column ion exchange is currently under evaluation to facilitate salt waste retrieval and processing in the Hanford tank farms. Spherical resorcinol formaldehyde (sRF) resin is the baseline ion exchange resin for use in the Waste Treatment and Immobilization Plant (WTP). This document provides background and technical rationale to assist in determining whether spherical resorcinol formaldehyde (sRF) is also the appropriate ion exchange resin for supplemental LAW pretreatment processes and compares sRF with crystalline silicotitanate (CST) as potential supplemental pretreatment ion exchange media.

  15. Microsoft SQL Server 2012 Licensing Guide

    E-Print Network [OSTI]

    Chaudhuri, Surajit

    Microsoft SQL Server 2012 Licensing Guide #12;2 Contents Overview......................................................................................................................................................................................................3 SQL Server 2012 Editions ......................................................................................................................................................................4 How SQL Server 2012 Licenses Are Sold

  16. LOS ALAMOS NATIONAL LABORATORY - EXPRESS LICENSING PROGRAM

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    LOS ALAMOS NATIONAL LABORATORY - EXPRESS LICENSING PROGRAM NON-EXCLUSIVE PATENT LICENSE AGREEMENT This Agreement between Los Alamos National Security, LLC ("LANS"), under its...

  17. Technologies Available for Licensing | Partnerships | ORNL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ORNL Technologies Licensing Guidelines NDA(s) and MTA(s) Sample Agreements Technology Innovation Program Technology Assistance Program Licensing Staff Technology Search Engine...

  18. Dominica Grants Geothermal Exploration and Development License...

    Office of Environmental Management (EM)

    Dominica Grants Geothermal Exploration and Development License to Caribbean Company Dominica Grants Geothermal Exploration and Development License to Caribbean Company July 23,...

  19. Technical data base quarterly report, April--June 1992; Yucca Mountain Site Characterization Project

    SciTech Connect (OSTI)

    NONE

    1992-09-01T23:59:59.000Z

    The acquisition and development of technical data are activities that provide the information base from which the Yucca mountain Site will be characterized and may P-ventually be licensed as a high-level waste repository. The Project Technical Data Base (TDB) is the repository for the regional and site-specific technical data required in intermediate and license application analyses and models. The TDB Quarterly Report provides the mechanism for identifying technical data currently available from the Project TDB. Due to the variety of scientific information generated by YMP activities, the Project TDB consists of three components, each designed to store specific types of data. The Site and Engineering Properties Data Base (SEPDB) maintains technical data best stored in a tabular format. The Geographic Nodal Information Study and Evaluation System (GENISES), which is the Geographic Information System (GIS) component of the Project TDB, maintains spatial or map-like data. The Geologic and Engineering Materials Bibliography of Chemical Species (GEMBOCHS) data base maintains thermodynamic/geochemical data needed to support geochemical reaction models involving the waste package and repository geochemical environment. Each of these data bases are addressed independently within the TDB Quarterly Report.

  20. Engineering support services for the DOE/GRI coal gasification research program. Quarterly technical progress report, January-March 1982

    SciTech Connect (OSTI)

    Bostwick, L.E.; Ethridge, T.R.; Starr, D.W.; Koneru, P.B.; Hubbard, D.A.; Shah, K.V.; Smith, M.R.; Ward, W.E.; Wong, E.W.

    1982-05-01T23:59:59.000Z

    Kellogg continued to actively monitor operations at BI-GAS, Westinghouse and IGT (for peat gasification). Pilot plant/PDU test runs which were monitored and reported included BI-GAS Tests G-18, G-18A and G-18B; Westinghouse PDU Test TP-032-1 and CFSF Test TP-M003; and Peatgas Pilot Plant Test No. 5. Kellogg also monitored winterization/maintenance activities at BI-GAS and Westinghouse and precommissioning of the IGT Wet Carbonization PDU. The final report on the Hygas Data Base Evaluation was issued, while final revisions were completed for the reports concerning PDU data base evaluations of Peatgas and single-stage peat gasification. Efforts toward completion of the brochure describing the DOE/GRI Joint Program proceeded. Normal MPC activities continued. Several technical progress reports were issued during this quarter.

  1. GPHS-RTGs in support of the Cassini Mission. Semi annual technical report, March 31, 1997--September 28, 1997

    SciTech Connect (OSTI)

    NONE

    1997-10-20T23:59:59.000Z

    This progress report describes work on the Radioisotope Thermoelectric Generators and Ancillary Activities carried out as part of the Cassini project. Seperate sections of the report describe activities carried out in support of different tasks assigned as part of this contract.

  2. Statement of work for solar thermal power systems and photovoltaic solar-energy systems technical support services

    SciTech Connect (OSTI)

    none,

    1982-01-01T23:59:59.000Z

    Work is broken down in the following areas: solar thermal central receiver systems analysis; advanced solar thermal systems analysis and engineering; thermal power systems support; total energy systems mission analysis; irrigation and small community mission analysis; photovoltaics mission analysis; Solar Thermal Test Facility and Central Receiver Pilot Plant systems engineering. (LEW)

  3. Technical Support for China's Village Electrification Program: Cooperative Research and Development Final Report, CRADA number CRD-07-00235

    SciTech Connect (OSTI)

    Kline, D.

    2010-07-01T23:59:59.000Z

    This work has two main goals: First, it provides for the analysis of data collected from systems developed in the previous phase of China's rural power program, the Township Electrification Program Second, it will comprise joint IEE-NREL work in support of the upcoming phase, 'Electrification of Unelectrified Areas'.

  4. Provision of utility support services to the US Department of Energy San Francisco Operations Office. Final technical report

    SciTech Connect (OSTI)

    Not Available

    1994-04-01T23:59:59.000Z

    The main purpose of this project was to provide to DOE/SAN continuing, follow-up support to realize savings from a number of alternate supply arrangements that had already been and/or were expected to be identified under the original project. This expected continuation of these efforts is demonstrated by certain of the tasks that are spelled out in the Statement of Work. For example: Evaluate and propose alternative options and methods for improving efficiency, reducing cost, and making effective use of the energy supplies and facilities under various conditions of use; Provide engineering and economic analysis and recommendations for utility-related facilities and service issues, such as high voltage discounts, ownership of facilities, etc.; Assist in developing strategy and documentation in support of negotiating utility contracts and modifications thereto. In addition, the follow-on contract provided for monitoring and intervening in rate cases that had particular relevance to the DOE/SAN laboratories.

  5. Technical documentation in support of the project-specific analysis for construction and operation of the National Ignition Facility

    SciTech Connect (OSTI)

    Lazaro, M.A.; Vinikour, W. [Argonne National Lab., IL (United States). Environmental Assessment Div.; Allison, T. [Argonne National Lab., IL (United States). Decision and Information Sciences Div.] [and others

    1996-09-01T23:59:59.000Z

    This document provides information that supports or supplements the data and impact analyses presented in the National Ignition Facility (NIF) Project-Specific Analysis (PSA). The purposes of NIF are to achieve fusion ignition in the laboratory for the first time with inertial confinement fusion (ICF) technology and to conduct high- energy-density experiments ins support of national security and civilian application. NIF is an important element in the DOE`s science-based SSM Program, a key mission of which is to ensure the reliability of the nation`s enduring stockpile of nuclear weapons. NIF would also advance the knowledge of basic and applied high-energy- density science and bring the nation a large step closer to developing fusion energy for civilian use. The NIF PSA includes evaluations of the potential environmental impacts of constructing and operating the facility at one of five candidate site and for two design options.

  6. ARRA FEMP Technical Assistance -- Federal Aviation Administration Project 209 -- Control Tower and Support Building, Palm Springs, CA

    SciTech Connect (OSTI)

    Arends, J.; Sandusky, William F.

    2010-03-31T23:59:59.000Z

    This report represents findings of a design review team that evaluated construction documents (at the 100% level) and operating specifications for a new control tower and support building that will be built in Palm Springs, California by the Federal Aviation Administration (FAA). The focus of the review was to identify measures that could be incorporated into the final design and operating specifications that would result in additional energy savings for the FAA that would not have otherwise occurred.

  7. Solar Hot Water Contractor Licensing

    Broader source: Energy.gov [DOE]

    In order to be eligible for Maine's solar thermal rebate program, systems must be installed by licensed plumbers who have received additional certification for solar thermal systems from the North...

  8. Vice President, Engineering and Technical Services

    Broader source: Energy.gov [DOE]

    The Engineering and Technical Services organization is responsible for implementing the transmission capital program, providing technical support for the transmission maintenance program and...

  9. ANL technical support program for DOE Environmental Restoration and Waste Management. Annual report, October 1991--September 1992

    SciTech Connect (OSTI)

    Bates, J.K.; Bradley, C.R.; Buck, E.C.; Cunnane, J.C.; Dietz, N.L.; Ebert, W.L.; Emery, J.W.; Feng, X.; Gerding, T.J.; Gong, M.; Hoh, J.C.; Mazer, J.J.; Wronkiewicz, D.J. [Argonne National Lab., IL (United States); Bourcier, W.L.; Morgan, L.E.; Newton, L.; Nielsen, J.K.; Phillips, B.L. [Lawrence Livermore National Lab., CA (United States); Ewing, R.C.; Wang, L. [Univ. of New Mexico, Albuquerque, NM (United States); Li, H.; Tomozawa, M. [Rensselaer Polytechnic Inst., Troy, NY (United States)

    1993-05-01T23:59:59.000Z

    A program was established for DOE Environmental Restoration and Waste Management (EM) to evaluate factors that are anticipated to affect waste glass reaction during repository disposal, especially in an unsaturated environment typical of what may be expected for the proposed Yucca Mountain repository site. This report covers progress in FY 1992 on the following tasks: 1. A compendium of the characteristics of high-level nuclear waste borosilicate glass has been written. 2. A critical review of important parameters that affect the reactivity of glass in an unsaturated environment is being prepared. 3. A series of tests has been started to evaluate the reactivity of fully radioactive glasses in a high-level waste repository environment and compare it to the reactivity of synthetic, nonradioactive glasses of similar composition. 4. The effect of radiation upon the durability of waste glasses at a high glass surface area-to-liquid volume (SA/V) ratio and a high gas-to-liquid volume ratio will be assessed. These tests address both vapor and high SA/V liquid conditions. 5. A series of tests is being performed to compare the extent of reaction of nuclear waste glasses at various SAN ratios. Such differences in the SAN ratio may significantly affect glass durability. 6. A series of natural analogue tests is being analyzed to demonstrate a meaningful relationship between experimental and natural alteration conditions. 7. Analytical electron microscopy (AEM), infrared spectroscopys and nuclear resonant profiling are being used to assess the glass/water reaction pathway by identifying intermediate phases that appear on the reacting glass. Additionally, colloids from the leach solutions are being studied using AEM. 8. A technical review of AEM results is being provided. 9. A study of water diffusion involving nuclear waste glasses is being performed. 10. A mechanistically based model is being developed to predict the performance of glass over repository-relevant time periods.

  10. High temperature turbine technology program. Phase II. Technology test and support studies. Annual technical progress report, January 1, 1979-December 31, 1979

    SciTech Connect (OSTI)

    Not Available

    1980-01-01T23:59:59.000Z

    Work performed on the High Temperature Turbine Technology Program, Phase II - Technology Test and Support Studies during the period from January 1, 1979 through December 31, 1979 is summarized. Objectives of the program elements as well as technical progress and problems encountered during this Phase II annual reporting period are presented. Progress on design, fabrication and checkout of test facilities and test rigs is described. LP turbine cascade tests were concluded. 350 hours of testing were conducted on the LP rig engine first with clean distillate fuel and then with fly ash particulates injected into the hot gas stream. Design and fabrication of the turbine spool technology rig components are described. TSTR 60/sup 0/ sector combustor rig fabrication and testing are reviewed. Progress in the design and fabrication of TSTR cascade rig components for operation on both distillate fuel and low Btu gas is described. The new coal-derived gaseous fuel synthesizing facility is reviewed. Results and future plans for the supporting metallurgical programs are discussed.

  11. Technical support document: Energy conservation standards for consumer products: Dishwashers, clothes washers, and clothes dryers including: Environmental impacts; regulatory impact analysis

    SciTech Connect (OSTI)

    Not Available

    1990-12-01T23:59:59.000Z

    The Energy Policy and Conservation Act as amended (P.L. 94-163), establishes energy conservation standards for 12 of the 13 types of consumer products specifically covered by the Act. The legislation requires the Department of Energy (DOE) to consider new or amended standards for these and other types of products at specified times. This Technical Support Document presents the methodology, data and results from the analysis of the energy and economic impacts of standards on dishwashers, clothes washers, and clothes dryers. The economic impact analysis is performed in five major areas: An Engineering Analysis, which establishes technical feasibility and product attributes including costs of design options to improve appliance efficiency. A Consumer Analysis at two levels: national aggregate impacts, and impacts on individuals. The national aggregate impacts include forecasts of appliance sales, efficiencies, energy use, and consumer expenditures. The individual impacts are analyzed by Life-Cycle Cost (LCC), Payback Periods, and Cost of Conserved Energy (CCE), which evaluate the savings in operating expenses relative to increases in purchase price; A Manufacturer Analysis, which provides an estimate of manufacturers' response to the proposed standards. Their response is quantified by changes in several measures of financial performance for a firm. An Industry Impact Analysis shows financial and competitive impacts on the appliance industry. A Utility Analysis that measures the impacts of the altered energy-consumption patterns on electric utilities. A Environmental Effects analysis, which estimates changes in emissions of carbon dioxide, sulfur oxides, and nitrogen oxides, due to reduced energy consumption in the home and at the power plant. A Regulatory Impact Analysis collects the results of all the analyses into the net benefits and costs from a national perspective. 47 figs., 171 tabs. (JF)

  12. Assessment and recommendations for fissile-material packaging exemptions and general licenses within 10 CFR Part 71

    SciTech Connect (OSTI)

    Parks, C.V.; Hopper, C.M.; Lichtenwalter, J.L. [Oak Ridge National Lab., TN (United States)

    1998-07-01T23:59:59.000Z

    This report provides a technical and regulatory assessment of the fissile material general licenses and fissile material exemptions within Title 10 of the Code of Federal Regulations Part 71. The assessment included literature studies and calculational analyses to evaluate the technical criteria; review of current industry practice and concerns; and a detailed evaluation of the regulatory text for clarity, consistency and relevance. Recommendations for potential consideration by the Nuclear Regulatory Commission staff are provided. The recommendations call for a simplification and consolidation of the general licenses and a change in the technical criteria for the first fissile material exemptions.

  13. Windows Server 2008 R2 Licensing Guide

    E-Print Network [OSTI]

    Narasayya, Vivek

    Windows Server 2008 R2 Licensing Guide m Your Comprehensive Resource for Licensing and Pricing #12;2 Table of Contents Summary 3 Table of Windows Server 2008 R2 Core Product Offerings 3 License Terms ­ Windows Server 2008 R2 Product Line Updates 4 Edition Comparison by Server Role 5 New and Updated Features

  14. Licensed fuel facility status report

    SciTech Connect (OSTI)

    Joy, D.; Brown, C.

    1993-04-01T23:59:59.000Z

    NRC is committed to the periodic publication of licensed fuel facilities inventory difference data, following agency review of the information and completion of any related NRC investigations. Information in this report includes inventory difference data for active fuel fabrication facilities possessing more than one effective kilogram of high enriched uranium, low enriched uranium, plutonium, or uranium-233.

  15. NRC safety research in support of regulation - FY 1994. Volume 9

    SciTech Connect (OSTI)

    NONE

    1995-06-01T23:59:59.000Z

    This report, the tenth in a series of annual reports, was prepared in response to congressional inquiries concerning how nuclear regulatory research is used. It summarizes the accomplishments of the Office of Nuclear Regulatory Research during FY 1994. The goal of the Office of Nuclear Regulatory Research (RES) is to ensure the availability of sound technical bases for timely rulemaking and related decisions in support of NRC regulatory/licensing/inspection activities. RES also has responsibilities related to the resolution of generic safety issues and to the review of licensee submittals regarding individual plant examinations. It is the responsibility of RES to conduct the NRC`s rulemaking process, including the issuance of regulatory guides and rules that govern NRC licensed activities.

  16. GPHS-RTGs in support of the Cassini mission. Semi-annual technical report, 30 March 1992--27 September 1992

    SciTech Connect (OSTI)

    Not Available

    1992-10-01T23:59:59.000Z

    The technical progress achieved during the period 30 March through 27 September 1992 on Contract DE-AC03-91SF18852.000 Radioisotope Thermoelectric Generators and Acillary Activities is described herein.

  17. Aging management of nuclear power plant containments for license renewal

    SciTech Connect (OSTI)

    Liu, W.C.; Kuo, P.T.; Lee, S.S.

    1997-09-01T23:59:59.000Z

    In 1990, the Nuclear Management and Resources Council (NUMARC), now the Nuclear Energy Institute (NEI), submitted for NRC review, the industry reports (IRs), NUMARC Report 90-01 and NUMARC Report 90-10, addressing aging management issues associated with PWR containments and BWR containments for license renewal, respectively. In 1996, the Commission amended 10 CFR 50.55a to promulgate requirements for inservice inspection of containment structures. This rule amendment incorporates by reference the 1992 Edition with the 1992 Addenda of Subsections IWE and IWL of the ASME Code addressing the inservice inspection of metal containments/liners and concrete containments, respectively. The purpose of this report is to reconcile the technical information and agreements resulting from the NUMARC IR reviews which are generally described in NUREG-1557 and the inservice inspection requirements of subsections IWE and IWL as promulgated in {section}50.55a for license renewal consideration. This report concludes that Subsections IWE and IWL as endorsed in {section}50.55a are generally consistent with the technical agreements reached during the IR reviews. Specific exceptions are identified and additional evaluations and augmented inspections for renewal are recommended.

  18. Los Alamos National Laboratory Express Licensing Requirements

    E-Print Network [OSTI]

    contact Laura Barber at Licensing@lanl.gov. Your company information will be treated as "business sensitive" or "proprietary" and will be handled accordingly. #12;

  19. Battelle Memorial Institute Technologies Available for Licensing...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and Fuels Wind Energy Partners (27) Visual Patent Search Success Stories News Events Battelle Memorial Institute Technologies Available for Licensing Battelle is the world's...

  20. Technology available for licensing: CURLS | Argonne National...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Technology available for licensing: CURLS November 21, 2013 Tweet EmailPrint CURLS - the Containment Unidirectional Resource Loading System developed at Argonne - expands the...

  1. Task Order Awarded for Environmental Technical Services | Department...

    Broader source: Energy.gov (indexed) [DOE]

    Project Office Audit Task Order Awarded for Technical and Safety Support Services DOE Issues Request for Quotations for Depleted Uranium Hexafluoride Conversion Technical Services...

  2. This work is licensed under a CREATIVE COMMONS ATTRIBUTION-SHARE ALIKE 3.0 LICENSE

    E-Print Network [OSTI]

    1 This work is licensed under a CREATIVE COMMONS ATTRIBUTION-SHARE ALIKE 3.0 LICENSE (http://creativecommons.org/licenses/by-sa/3.0/) Mario Biagioli Department of the History of Science Harvard University 7/17/2007 EARLY MODERN

  3. Technology Licensing | ornl.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of ScienceandMesa del SolStrengthening a solidSynthesis of 2D AlloysTrails How To License ORNL

  4. SCALE: A modular code system for performing standardized computer analyses for licensing evaluation

    SciTech Connect (OSTI)

    NONE

    1997-03-01T23:59:59.000Z

    This Manual represents Revision 5 of the user documentation for the modular code system referred to as SCALE. The history of the SCALE code system dates back to 1969 when the current Computational Physics and Engineering Division at Oak Ridge National Laboratory (ORNL) began providing the transportation package certification staff at the U.S. Atomic Energy Commission with computational support in the use of the new KENO code for performing criticality safety assessments with the statistical Monte Carlo method. From 1969 to 1976 the certification staff relied on the ORNL staff to assist them in the correct use of codes and data for criticality, shielding, and heat transfer analyses of transportation packages. However, the certification staff learned that, with only occasional use of the codes, it was difficult to become proficient in performing the calculations often needed for an independent safety review. Thus, shortly after the move of the certification staff to the U.S. Nuclear Regulatory Commission (NRC), the NRC staff proposed the development of an easy-to-use analysis system that provided the technical capabilities of the individual modules with which they were familiar. With this proposal, the concept of the Standardized Computer Analyses for Licensing Evaluation (SCALE) code system was born. This manual covers an array of modules written for the SCALE package, consisting of drivers, system libraries, cross section and materials properties libraries, input/output routines, storage modules, and help files.

  5. Engineering-support services for the DOE/GRI coal-gasification research program. Quarterly technical progress report, October-December 1980

    SciTech Connect (OSTI)

    Bostwick, L.E.; Brancheau, R.J.; Chen, R.G.

    1980-01-01T23:59:59.000Z

    Kellogg activities included continued monitoring of test operations at BI-GAS, Westinghouse, Exxon and IGT (for peak gasification). Pilot plant/PDU test runs which were monitored and reported included: BI-GAS tests G-14, G-14A, G-15 and G-15A; Westinghouse PDU tests TP-027-5 and TP-031-1 and CFSF tests TP-M001-1, 2, 3 and 4; Exxon run periods No. 23 and No. 24; and IGT single-stage peat gasification tests BF-1 through BF-6. Draft reports were submitted regarding Hygas data base evaluation, gasifier vessel design and scaleup risks of the Westinghouse oxygen-blown gasifier. Evaluation of the Hygas data base continued, and a similar study of the Peatgas PDU data base was initiated. Work was begun on preparation of a descriptive brochure for the DOE/GRI joint program. Kellogg personnel participated in investigations of welding materials with the MPC. Significant progress was made in the technical/economic assessments of Westinghouse, Exxon and Peatgas and in the technical/economic comparison of Westinghouse and U-gas, with technical definitions being essentially finished and cost estimation begun. Technical definition and preliminary capital cost estimates were completed for the peat harvesting/dewatering study. Work continued in the study of carbonyl formation. Following reviews by the developers, Kellogg began finalization of the report on screening evaluations of Westinghouse, Exxon and Rockwell. Work on the safety assurance study continued, with the commencement of safety audit visits.

  6. TECHNICAL BASIS FOR DOE STANDARD 3013 EQUIVALENCY SUPPORTING REDUCED TEMPERATURE STABILIZATION OF OXALATE-DERIVED PLUTONIUM OXIDE PRODUCED BY THE HB-LINE FACILITY AT SAVANNAH RIVER SITE

    SciTech Connect (OSTI)

    Duffey, J.; Livingston, R.; Berg, J.; Veirs, D.

    2012-07-02T23:59:59.000Z

    The HB-Line (HBL) facility at the Savannah River Site (SRS) is designed to produce high-purity plutonium dioxide (PuO{sub 2}) which is suitable for future use in production of Mixed Oxide (MOX) fuel. The MOX Fuel Fabrication Facility (MFFF) requires PuO{sub 2} feed to be packaged per the U.S. Department of Energy (DOE) Standard 3013 (DOE-STD-3013) to comply with the facility's safety basis. The stabilization conditions imposed by DOE-STD-3013 for PuO{sub 2} (i.e., 950 C for 2 hours) preclude use of the HBL PuO{sub 2} in direct fuel fabrication and reduce the value of the HBL product as MFFF feedstock. Consequently, HBL initiated a technical evaluation to define acceptable operating conditions for production of high-purity PuO{sub 2} that fulfills the DOE-STD-3013 criteria for safe storage. The purpose of this document is to demonstrate that within the defined operating conditions, the HBL process will be equivalent for meeting the requirements of the DOE-STD-3013 stabilization process for plutonium-bearing materials from the DOE complex. The proposed 3013 equivalency reduces the prescribed stabilization temperature for high-purity PuO{sub 2} from oxalate precipitation processes from 950 C to 640 C and places a limit of 60% on the relative humidity (RH) at the lowest material temperature. The equivalency is limited to material produced using the HBL established flow sheet, for example, nitric acid anion exchange and Pu(IV) direct strike oxalate precipitation with stabilization at a minimum temperature of 640 C for four hours (h). The product purity must meet the MFFF acceptance criteria of 23,600 {micro}g/g Pu (i.e., 2.1 wt %) total impurities and chloride content less than 250 {micro}g/g of Pu. All other stabilization and packaging criteria identified by DOE-STD-3013-2012 or earlier revisions of the standard apply. Based on the evaluation of test data discussed in this document, the expert judgment of the authors supports packaging the HBL product under a 3013 equivalency. Under the defined process conditions and associated material specifications, the high-purity PuO{sub 2} produced in HBL presents no unique safety concerns for packaging or storage in the 3013 required configuration. The PuO{sub 2} produced using the HBL flow sheet conditions will have a higher specific surface area (SSA) than PuO{sub 2} stabilized at 950 C and, consequently, under identical conditions will adsorb more water from the atmosphere. The greatest challenge to HBL operators will be controlling moisture content below 0.5 wt %. However, even at the 0.5 wt % moisture limit, the maximum acceptable pressure of a stoichiometric mixture of hydrogen and oxygen in the 3013 container is greater than the maximum possible pressure for the HBL PuO{sub 2} product.

  7. Pipeline gas demonstration plant, Phase I. Quarterly technical progress report for September 1980-November 1980

    SciTech Connect (OSTI)

    Eby, R.J.

    1980-12-01T23:59:59.000Z

    Work was performed in the following tasks in Phase I of the Pipeline Gas Demonstration Plant Program: Site Evaluation and Selection; Demonstration Plant Environmental Analysis; Feedstock Plans, Licenses, Permits and Easements; Demonstration Plant Definitive Design; Construction Planning; Economic Reassessment; Technical Support; Long Lead Procurement List; and Project Management. The Preliminary Construction Schedule was delivered to the Government on October 3, 1980, constituting an early delivery of the construction schedule called for in the scope of work for Task VI. The major work activity continues to be the effort in Task VI, Demonstration Plant Definitive Design, with two 30% Design Review meetings being held with the Government. Work in Task VII, Construction Planning, was initiated. Work has progressed satisfactorily in the other tasks in support of the Demonstration Plant Program. A Cost Change Proposal was submitted because of an increase in the scope of work and an extension of the schedule for Phase I to 47 months.

  8. INTERNAL HAZARDS ANALYSIS FOR LICENSE APPLICATION

    SciTech Connect (OSTI)

    R.J. Garrett

    2005-02-17T23:59:59.000Z

    The purpose of this internal hazards analysis is to identify and document the internal hazards and potential initiating events associated with preclosure operations of the repository at Yucca Mountain. Internal hazards are those hazards presented by the operation of the facility and by its associated processes that can potentially lead to a radioactive release or cause a radiological hazard. In contrast to external hazards, internal hazards do not involve natural phenomena and external man-made hazards. This internal hazards analysis was performed in support of the preclosure safety analysis and the License Application for the Yucca Mountain Project. The methodology for this analysis provides a systematic means to identify internal hazards and potential initiating events that may result in a radiological hazard or radiological release during the repository preclosure period. These hazards are documented in tables of potential internal hazards and potential initiating events (Section 6.6) for input to the repository event sequence categorization process. The results of this analysis will undergo further screening and analysis based on the criteria that apply to the performance of event sequence analyses for the repository preclosure period. The evolving design of the repository will be re-evaluated periodically to ensure that internal hazards that have not been previously evaluated are identified.

  9. Branch technical position on the use of expert elicitation in the high-level radioactive waste program

    SciTech Connect (OSTI)

    Kotra, J.P.; Lee, M.P.; Eisenberg, N.A. [Nuclear Regulatory Commission, Washington, DC (United States); DeWispelare, A.R. [Center for Nuclear Waste Regulatory Analyses, San Antonio, TX (United States)

    1996-11-01T23:59:59.000Z

    Should the site be found suitable, DOE will apply to the US Nuclear Regulatory Commission for permission to construct and then operate a proposed geologic repository for the disposal of spent nuclear fuel and other high-level radioactive waste at Yucca Mountain. In deciding whether to grant or deny DOE`s license application for a geologic repository, NRC will closely examine the facts and expert judgment set forth in any potential DOE license application. NRC expects that subjective judgments of individual experts and, in some cases, groups of experts, will be used by DOE to interpret data obtained during site characterization and to address the many technical issues and inherent uncertainties associated with predicting the performance of a repository system for thousands of years. NRC has traditionally accepted, for review, expert judgment to evaluate and interpret the factual bases of license applications and is expected to give appropriate consideration to the judgments of DOE`s experts regarding the geologic repository. Such consideration, however, envisions DOE using expert judgments to complement and supplement other sources of scientific and technical information, such as data collection, analyses, and experimentation. In this document, the NRC staff has set forth technical positions that: (1) provide general guidelines on those circumstances that may warrant the use of a formal process for obtaining the judgments of more than one expert (i.e., expert elicitation); and (2) describe acceptable procedures for conducting expert elicitation when formally elicited judgments are used to support a demonstration of compliance with NRC`s geologic disposal regulation, currently set forth in 10 CFR Part 60. 76 refs.

  10. Technical Assistance to Developers

    SciTech Connect (OSTI)

    Rockward, Tommy [Los Alamos National Laboratory; Borup, Rodney L. [Los Alamos National Laboratory; Garzon, Fernando H. [Los Alamos National Laboratory; Mukundan, Rangachary [Los Alamos National Laboratory; Spernjak, Dusan [Los Alamos National Laboratory

    2012-07-17T23:59:59.000Z

    This task supports the allowance of technical assistance to fuel-cell component and system developers as directed by the DOE. This task includes testing of novel materials and participation in the further development and validation of single cell test protocols. This task also covers technical assistance to DOE Working Groups, the U.S. Council for Automotive Research (USCAR) and the USCAR/DOE Driving Research and Innovation for Vehicle efficiency and Energy sustainability (U.S. Drive) Fuel Cell Technology Team. Assistance includes technical validation of new fuel cell materials and methods, single cell fuel cell testing to support the development of targets and test protocols, and regular advisory participation in other working groups and reviews. This assistance is made available to PEM fuel cell developers by request and DOE Approval. The objectives are to: (1) Support technically, as directed by DOE, fuel cell component and system developers; (2) Assess fuel cell materials and components and give feedback to developers; (3) Assist the DOE Durability Working Group with the development of various new material durability Testing protocols; and (4) Provide support to the U.S. Council for Automotive Research (USCAR) and the USCAR/DOE Fuel Cell Technology Team. FY2012 specific technical objectives are: (1) Evaluate novel MPL materials; (2) Develop of startup/ shutdown protocol; (3) Test the impact of hydrophobic treatment on graphite bi-polar plates; (4) Perform complete diagnostics on metal bi-polar plates for corrosion; and (5) Participate and lead efforts in the DOE Working Groups.

  11. Consolidated guidance about materials licenses: Program-specific guidance about portable gauge licenses. Final report; Volume 1

    SciTech Connect (OSTI)

    Vacca, P.C.; Whitten, J.E.; Pelchat, J.M.; Arredondo, S.A.; Matson, E.R.; Lewis, S.H.; Collins, D.J.; Santiago, P.A. [Nuclear Regulatory Commission, Washington, DC (United States). Div. of Industrial and Medical Nuclear Safety; Tingle, W. [Dept. of Environment, Health, and Natural Resources, Raleigh, NC (United States). Div. of Radiation Protection

    1997-05-01T23:59:59.000Z

    As part of its redesign of the materials licensing process, NRC is consolidating and updating numerous guidance documents into a single comprehensive repository as described in NUREG-1539 and draft NUREG-1541. NUREG-1556, Vol. 1, is the first program-specific guidance developed for the new process and will serve as a template for subsequent program-specific guidance. This document is intended for use by applicants, licensees, and NRC staff and will also be available to Agreement States. This document supersedes the guidance previously found in draft Regulatory Guide DG-0008, ``Applications for the Use of Sealed Sources in Portable Gauging Devices,`` and in NMSs Policy and guidance Directive 2-07, ``Standard Review Plan for Applications for Use of Sealed Sources in Portable Gauging Devices.`` This final report takes a more risk-informed, performance-based approach to licensing portable gauges, and reduces the information(amount and level of detail) needed to support an application to use these devices. It incorporates many suggests submitted during the comment period on draft NUREG-1556, Volume 1. When published, this final report should be used in preparing portable gauge license applications. NRC staff will use this final report in reviewing these applications.

  12. Hanau licenses voided by German state court

    SciTech Connect (OSTI)

    Not Available

    1993-09-01T23:59:59.000Z

    On July 21, the Higher Administrative Court in the German state of Hesse declared illegal three of the first four partial construction licenses for the plutonium section of the Siemens fuel fabrication complex at Hanau. The licenses were issued in the late 1980s by the former Christian Democrat administration of Hesse, but final licensing of the plant - now 90 percent complete - has been held up by the Social Democrat/Green Party coalition government that is now in power. The court ruling came as a result of four cases, and a so-called urgent application, initiated by antinuclear groups in the area.

  13. NASA Partners License Nanotube Technology for Commercial Use...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    prnewswire.comnews-releasesnasa-partners-license-nanotube-technology-for-commercial-use-149724205.html Submitted: Tuesday, May...

  14. APS Engineering Support Division (AES) | Advanced Photon Source

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    APS Engineering Support Division (AES) The APS Engineering Support Division provides reliable operations and technical support to the Advanced Photon Source user community. AES...

  15. Technical Guidance

    Broader source: Energy.gov [DOE]

    The Office of Technical Guidance, within the Office of Health, Safety and Security develops and issues Government-wide and Department-wide technical guidance to ensure that classified nuclear...

  16. TECHNICAL BASIS FOR DOE STANDARD 3013 EQUIVALENCY SUPPORTING REDUCED TEMPERATURE STABILIZATION OF OXALATE-DERIVED PLUTONIUM DIOXIDE PRODUCED BY THE HB-LINE FACILITY AT SAVANNAH RIVER SITE

    SciTech Connect (OSTI)

    Duffey, J. M.; Livingston, R. R.; Berg, J. M.; Veirs, D. K.

    2013-02-06T23:59:59.000Z

    This report documents the technical basis for determining that stabilizing highpurity PuO{sub 2} derived from oxalate precipitation at the SRS HB-Line facility at a minimum of 625 {degree}C for at least four hours in an oxidizing atmosphere is equivalent to stabilizing at a minimum of 950 {degree}C for at least two hours as regards meeting the objectives of stabilization defined by DOE-STD-3013 if the material is handled in a way to prevent excessive absorption of water.

  17. Onboard Hydrogen/Helium Sensors in Support of the Global Technical Regulation: An Assessment of Performance in Fuel Cell Electric Vehicle Crash Tests

    SciTech Connect (OSTI)

    Post, M. B.; Burgess, R.; Rivkin, C.; Buttner, W.; O'Malley, K.; Ruiz, A.

    2012-09-01T23:59:59.000Z

    Automobile manufacturers in North America, Europe, and Asia project a 2015 release of commercial hydrogen fuel cell powered light-duty road vehicles. These vehicles will be for general consumer applications, albeit initially in select markets but with much broader market penetration expected by 2025. To assure international harmony, North American, European, and Asian regulatory representatives are striving to base respective national regulations on an international safety standard, the Global Technical Regulation (GTR), Hydrogen Fueled Vehicle, which is part of an international agreement pertaining to wheeled vehicles and equipment for wheeled vehicles.

  18. Argument licensing and agreement in Zulu

    E-Print Network [OSTI]

    Halpert, Claire

    2012-01-01T23:59:59.000Z

    In this thesis, I examine some core grammatical phenomena - case licensing, agreement, the EPP - through the lens of the Bantu language Zulu. Zulu has a number of remarkable and puzzling properties whose analysis affords ...

  19. City of Dubuque- Solar Thermal Licensing Requirement

    Broader source: Energy.gov [DOE]

    The City of Dubuque requires a Solar Thermal License in order for a person to install a solar thermal project on a home or business. The requirement does not apply to solar photovoltaics. The...

  20. Engineering-support services for the DOE/GRI coal-gasification research program. Quarterly technical progress report, July-September 1981

    SciTech Connect (OSTI)

    Bostwick, L.E.; Ethridge, T.R.; Gilwood, W.C.; Glasgow, P.E.; Hubbard, D.A.; Shah, K.V.; Singer, D.L.; Smith, M.R.; Ward, W.E.

    1981-01-01T23:59:59.000Z

    During July-September 1981 Kellogg continued to actively monitor operations at BI-GAS, Westinghouse and IGT (for peat gasification). Pilot plant/PDU tests which were monitored and reported included BI-GAS Tests G-17D, G-17E, and G-17F; Westinghouse PDU test runs TP-0282 and TP-028-3 and CFSF Tests TP-M002-2 and TP-M006-1; Peatgas pilot plant Tests number 2 and number 3; and single-stage peat gasification PDU Test BF-21. Work on several task orders was completed with the issue of final reports on technical/economic assessments of Exxon, Westinghouse and Peatgas, the technical/economic comparison of Westinghouse and U-Gas, safety audits, safety assurance, peat harvesting and dewatering, gasifier vessel design and carbonyl formation. Kellogg continued its efforts toward completion of the descriptive brochure for the DOE/GRI Joint program and of the reports on the Hygas and Peatgas data bases. A new subtask, to evaluate the data base for single-stage peat gasification, was undertaken, and Kellogg participated in reviews of the Hygas final report. Normal MPC activities continued.

  1. Engineering-support services for the DOE/GRI coal-gasification research program. Quarterly technical progress report, April-June 1981

    SciTech Connect (OSTI)

    Bernard, D.M.; Bostwick, L.E.; Ethridge, T.R.; Gilwood, W.C.; Hubbard, D.A.; Montgomery, R.L.; Senules, E.A.; Singer, D.L.; Smith, M.R.; Ward, W.E.

    1981-01-01T23:59:59.000Z

    Kellog activities during April to June 1981 included continued monitoring of activities at Bi-Gas, Westinghouse, Exxon and IGT (for peat gasification). Pilot plant/PDU tests which were monitored and reported include Bi-Gas tests G-16B, G-17, G-17A, G-17B, and G-17C; Westinghouse PDU test runs TP-029-1/030-1, TP-030-2 and TP-028-1 and CFSF tests TP-M002-1 and TP-M002-2; Exxon run period number 28; Peatgas pilot plant Test RF-1 and gasification Test number 1; and IGT single-stage peat gasification PDU Tests BF-13 through BF-20. Significant milestones were reached with the issue of draft reports for several tasks, including carbonyl formation, peat harvesting/dewatering, technical/economic assessments of Exxon, Westinghouse and PeatGas, technical/economic comparison of Westinghouse and U-Gas, gasifier design, safety audits, Hygas data base evaluation and the safety assurance study. In addition, final reports were issued for the Westinghouse oxygen blown gasifier risk analysis and for the PDU screening evaluations of Exxon, Westinghouse and Rockwell. Work on the Peatgas PDU data base evaluation continued, and a review of the Hygas final report was begun.

  2. Engineering-support services for the DOE/GRI Coal-Gasification Research Program. Quarterly technical progress report, July-September 1980

    SciTech Connect (OSTI)

    Bostwick, L.E.; Brancheau, R.J.; Castiglioni, B.P.

    1982-01-01T23:59:59.000Z

    Kellogg activities included contained monitoring of test operations at the Hygas, BI-GAS, Westinghoue, Exxon and Bell plant sites. Peat gasification laboratory tests were also monitored; Rockwell testing ended during June. Pilot Plant/PDU test runs monitored and reported were: Hygas Test 87 (the last of the pilot plant series), BI-GAS Tests G-13 and G-14, Westinghouse test runs TP-027, TP-027-4 and TP-027-5, Exxon test periods 19 through 21 and Bell Tests 2174 through 3195. Kellogg continued its work on the Hygas data base evaluation and began an evaluation of the scaleup risks of the Westinghouse oxygen-blown gasifier. Work under new task orders was initiated. The topics included are: Technical/Economic Assessments of Westinghouse, Exxon and Peatgas, Gasifier Vessel Design, Technical/Economic Comparisons of Westinghouse and U-Gas, Peat Harvesting and Dewatering, and Carbonyl Formation in Coal Gasification processes. Economics are essentially complete for the Screening Evaluations of Westinghouse, Exxon and Rockwell and report preparation has begun. Work on the Pilot/Plant PDU Safety Evaluation Task continued.

  3. SAE Standards Support

    SciTech Connect (OSTI)

    Gowri, Krishnan

    2012-11-01T23:59:59.000Z

    This report summarizes PNNL activities in FY 2012 in support of the following two vehicle communication standards activities: • Technical support to SAE, ANSI and NIST technical working groups. PNNL actively contributed to the use case development, harmonization, and evaluation of the SAE standards activities for vehicle to grid communication • Tested and validated a set of potential technologies for meeting SAE communication requirements and provided recommendations for technology choices.

  4. OSH technical reference manual

    SciTech Connect (OSTI)

    Not Available

    1993-11-01T23:59:59.000Z

    In an evaluation of the Department of Energy (DOE) Occupational Safety and Health programs for government-owned contractor-operated (GOCO) activities, the Department of Labor`s Occupational Safety and Health Administration (OSHA) recommended a technical information exchange program. The intent was to share written safety and health programs, plans, training manuals, and materials within the entire DOE community. The OSH Technical Reference (OTR) helps support the secretary`s response to the OSHA finding by providing a one-stop resource and referral for technical information that relates to safe operations and practice. It also serves as a technical information exchange tool to reference DOE-wide materials pertinent to specific safety topics and, with some modification, as a training aid. The OTR bridges the gap between general safety documents and very specific requirements documents. It is tailored to the DOE community and incorporates DOE field experience.

  5. Facility worker technical basis document

    SciTech Connect (OSTI)

    SHULTZ, M.V.

    2003-08-28T23:59:59.000Z

    This technical basis document was developed to support the Tank Farm Documented Safety Analysis (DSA). It describes the criteria and methodology for allocating controls to hazardous conditions with significant facility work consequence and presents the results of the allocation.

  6. Sodium fast reactor safety and licensing research plan. Volume I.

    SciTech Connect (OSTI)

    Sofu, Tanju (Argonne National Laboratory, Argonne, IL); LaChance, Jeffrey L.; Bari, R. (Brokhaven National Laboratory Upton, NY); Wigeland, Roald (Idaho National Laboratory, Idaho Falls, ID); Denman, Matthew R.; Flanagan, George F. (Oak Ridge National Laboratory, Oak Ridge, TN)

    2012-05-01T23:59:59.000Z

    This report proposes potential research priorities for the Department of Energy (DOE) with the intent of improving the licensability of the Sodium Fast Reactor (SFR). In support of this project, five panels were tasked with identifying potential safety-related gaps in available information, data, and models needed to support the licensing of a SFR. The areas examined were sodium technology, accident sequences and initiators, source term characterization, codes and methods, and fuels and materials. It is the intent of this report to utilize a structured and transparent process that incorporates feedback from all interested stakeholders to suggest future funding priorities for the SFR research and development. While numerous gaps were identified, two cross-cutting gaps related to knowledge preservation were agreed upon by all panels and should be addressed in the near future. The first gap is a need to re-evaluate the current procedures for removing the Applied Technology designation from old documents. The second cross-cutting gap is the need for a robust Knowledge Management and Preservation system in all SFR research areas. Closure of these and the other identified gaps will require both a reprioritization of funding within DOE as well as a re-evaluation of existing bureaucratic procedures within the DOE associated with Applied Technology and Knowledge Management.

  7. ISET Journal of Earthquake Technology, Technical Note, Vol. 46, No. 3-4, Sept.-Dec. 2009, pp. 147155 APPLICATION OF LEAST SQUARES SUPPORT VECTOR MACHINE IN

    E-Print Network [OSTI]

    Gupta, Vinay Kumar

    support vector machine (LSSVM) in the prediction of seismic attenuation based on rock properties, Attenuations, and Petrophysical Properties of Reservoir Sedimentary Rocks", Geophysical Prospecting, Vol. 42­191. 4. Boadu, F.K. (1997). "Rock Properties and Seismic Attenuation: Neural Network Analysis", Pure

  8. License Structure for Multi-Module Facilities

    SciTech Connect (OSTI)

    Thomas Hicks

    2010-08-01T23:59:59.000Z

    The Next Generation Nuclear Plant (NGNP) Project is intended to be the prototype for multi-module commercial high temperature gas reactors (HTGRs) for process heat and/or electricity generation. Part of the objectives of the project are to establish the conditions that would govern or enhance the design, licensing, construction and operation of numerous, modular nuclear plants, particularly suited for industrial applications or that could reduce the risk of such projects. A determination is desired regarding whether a multi-module reactor plant can be licensed with a single Nuclear Regulatory Commission (NRC) review, hearing, and safety evaluation report. If it is determined that a multi-modular reactor plant can be licensed under a single review/hearing process, the structure and the duration of the license for each module will also need to be determined. The purpose of this paper is to describe for the NRC the NGNP position on these two issues and obtain either NRC general concurrence or comments on the approach to these issues. While the current NGNP planning provides for only a single reactor module, the project is intended to provide the basis and establish a licensing framework that can be used by future commercial HTGRs and other reactor designs, including a variety of small modular reactor technologies, with configurations reflecting design standardization of multi-module plants. Therefore, it is important to identify a path for addressing these modular reactor plant issues so that the resolution can be factored into the NGNP Project planning. The NGNP position is that a single combined license (COL) application can be submitted for a multi-modular reactor facility, the COL application can undergo a single NRC review/hearing process, and each module should be issued a separate license.

  9. Licensing review of foreign I and C systems for Ukrainian nuclear power plants

    SciTech Connect (OSTI)

    Brenman, O. [Westinghouse Electric Company, 4350 Northern Pike, Monroeville, PA 15146 (United States); Denning, R. S.; Cybulskis, P. [Battelle, 505 King Ave., Columbus, OH 43201 (United States); Vynogradskaia, S. V.; Yastrebenetsky, M. A. [SSTC NRS, Chernishevsky Str.53, Kharkov, 61002 (Ukraine); Afanasiev, N. V. [PO South Ukraine NPP, NAEK Energoatom, Yuzhnoukrainsk. Mykolayv Region 55000 (Ukraine)

    2006-07-01T23:59:59.000Z

    This paper describes the licensing process of the foreign-supplied systems for Ukrainian Nuclear Power Plants, starting from the tender package and specifications (Terms of Reference), through the implementation activities, and to the system final acceptance. Special attention is given to the licensing reviews of I and C software and Preliminary and Final Safety Analysis Reports. The actual licensing process involves the submission of many documents from the plant designer, the NPP, the foreign supplier, expert institution, and others, such as the State Scientific-and-Technical Center for Nuclear and Radiation Safety (SSTC NRS), and requires various expert reviews and approvals from the Ukrainian regulatory body State Nuclear Regulatory Commission of Ukraine (SNRCU). It is extremely important for each foreign supplier to understand the split of responsibilities and scope of activities carried out by all parties involved in the licensing process. The paper summarizes extensive experience of the co-authors and provides some recommendations for international vendors who are considering supplying their I and C systems to Ukraine. (authors)

  10. Technical support document: Energy efficiency standards for consumer products: Room air conditioners, water heaters, direct heating equipment, mobile home furnaces, kitchen ranges and ovens, pool heaters, fluorescent lamp ballasts and television sets. Volume 1, Methodology

    SciTech Connect (OSTI)

    Not Available

    1993-11-01T23:59:59.000Z

    The Energy Policy and Conservation Act (P.L. 94-163), as amended, establishes energy conservation standards for 12 of the 13 types of consumer products specifically covered by the Act. The legislation requires the Department of Energy (DOE) to consider new or amended standards for these and other types of products at specified times. DOE is currently considering amending standards for seven types of products: water heaters, direct heating equipment, mobile home furnaces, pool heaters, room air conditioners, kitchen ranges and ovens (including microwave ovens), and fluorescent light ballasts and is considering establishing standards for television sets. This Technical Support Document presents the methodology, data, and results from the analysis of the energy and economic impacts of the proposed standards. This volume presents a general description of the analytic approach, including the structure of the major models.

  11. The Independent Technical Analysis Process

    SciTech Connect (OSTI)

    Duberstein, Corey A.; Ham, Kenneth D.; Dauble, Dennis D.; Johnson, Gary E.

    2007-04-13T23:59:59.000Z

    The Bonneville Power Administration (BPA) contracted with the Pacific Northwest National Laboratory (PNNL) to provide technical analytical support for system-wide fish passage information (BPA Project No. 2006-010-00). The goal of this project was to produce rigorous technical analysis products using independent analysts and anonymous peer reviewers. In the past, regional parties have interacted with a single entity, the Fish Passage Center to access the data, analyses, and coordination related to fish passage. This project provided an independent technical source for non-routine fish passage analyses while allowing routine support functions to be performed by other well-qualified entities.

  12. Final technical report for the Award DE-FG02-08ER64574, with list of 30 refereed journal articles that acknowledge support from this award.

    SciTech Connect (OSTI)

    Wojciech W. Grabowski

    2012-04-02T23:59:59.000Z

    In this project, we focused on applications of the new warm-rain and ice microphysics schemes to simulate various cloud systems. The overall goal was either to evaluate and improve specific aspects of the schemes (through comparisons with ARM/ASR observations) or to understand the coupling between aerosols, cloud microphysics and cloud dynamics in variety of situations. These studies are relevant to the indirect impact of atmospheric aerosols on climate. Below we report on selected key aspects of the research and then list all peer-reviewed papers that acknowledge support from this grant. Overall, studies partially supported by this grant resulted in 30 peer-reviewed publications (listed below), several dozens of conference presentations (including posters and oral presentations at the ASR Science Team Meetings), and two PhD dissertations. More detailed summaries of our accomplishments are included in yearly reports. Here we summarize only major efforts.

  13. American Recovery and Reinvestment Act (ARRA) FEMP Technical Assistance Federal Aviation Administration Project 209 - Control Tower and Support Building, Las Vegas, NV

    SciTech Connect (OSTI)

    Arends, J.; Sandusky, William F.

    2010-03-31T23:59:59.000Z

    This report represents findings of a design review team that evaluated construction documents (at the 70% level) and operating specifications for a new control tower and support building that will be built in Las Vegas, Nevada by the Federal Aviation Administration (FAA). The focus of the review was to identify measures that could be incorporated into the final design and operating specification that would result in additional energy savings for the FAA that would not have otherwise occurred.

  14. American Recovery and Reinvestment Act (ARRA) FEMP Technical Assistance Federal Aviation Administration – Project 209 Control Tower and Support Building Oakland, CA

    SciTech Connect (OSTI)

    Arends, J.; Sandusky, William F.

    2010-03-01T23:59:59.000Z

    This report represents findings of a design review team that evaluated construction documents (at the 70% level) and operating specifications for a new control tower and support building that will be build at Oakland, California by the Federal Aviation Administration (FAA). The focus of the review was to identify measures that could be incorporated into the final design and operating specification that would result in additional energy savings for the FAA that would not have otherwise occurred.

  15. Evaluation of using cyclocranes to support drilling and production of oil and gas in wetland areas. Fourth quarterly technical progress report, Second quarter, 1993

    SciTech Connect (OSTI)

    Eggington, W.J.

    1993-09-01T23:59:59.000Z

    The planned program falls under wetlands area research related to drilling, production, and transportation of oil and gas resources. Specifically the planned program addresses an evaluation of using cyclocraft to transport drill rigs, mud, pipes and other materials and equipment in a cost effective and environmentally safe manner to support oil and gas drilling and production operations in wetland areas. The cyclocraft is a proven hybrid aircraft that utilizes aerostatic and aerodynamic lift. This type of aircraft has considerable payload capacity, VTOL capability, high controllability, low operating cost, low downwash and high safety. The benefits of using a cyclocraft to transport drill rigs and materials over environmentally-sensitive surfaces would be significant. The cyclocraft has considerable cost and operational advantages over the helicopter. The major activity during the second quarter of 1993 was focussed on completion of Task 4, Preliminary Design. The selected design has been designated H.1 Cyclocraft by MRC. Also during the report period, Task 6, Ground Support, was completed and a report containing the results was submitted to DOE. This task addressed the complete H.1 Cyclocraft system, i.e. it included the need personnel, facilities and equipment to support cyclocraft operations in wetland areas.

  16. Dredging Operations Technical Support Program. General decision-making framework for management of dredged material: Example application to Commencement Bay, Washington. Final report

    SciTech Connect (OSTI)

    Lee, C.R.; Tatem, H.E.; Brandon, D.L.; Kay, S.H.; Peddicord, R.K.

    1991-06-01T23:59:59.000Z

    Navigable waterways of the United States have a vital role in the Nation's economic growth. The US Army Corps of Engineers is responsible for the dredging and disposal of large volumes of sediment each year. Dredging is a process by which sediments are removed from the bottom of streams, rivers, lakes, and coastal waters, transported via ship, barge, or pipeline, and discharged to land or water. The presence of contamination in some locations has generated concern that dredged material disposal may adversely affect water quality and aquatic organisms or terrestrial organisms. Since many of the waterways are located in industrial and urban areas, some sediments may be highly contaminated with hazardous materials. A general decision-making framework based on the results of technically sound tests protocols is described. The decision-making framework includes consideration of sediment chemistry, physical chemistry of disposal site environments, and biological effects of sediment contaminants, as well as comparison of test results from sediments to be dredged with test results from reference sediments and with established criteria. The framework provides the basis for selection of the environmentally preferable disposal alternative and for identification of potentially appropriate control measures to minimize problems associated with the presence of contaminants.

  17. Engineering support services for the DOE/GRI coal-gasification research program. Quarterly technical progress report, April-June 1980

    SciTech Connect (OSTI)

    Bostwick, L.E.; Brancheau, R.J.; Chen, R.G.

    1980-01-01T23:59:59.000Z

    Kellogg activities included continued monitoring of test operations at the Hygas, BI-GAS, Westinghouse, Exxon, Rockwell and Bell plant sites, and of peat gasification laboratory activities. Pilot plant/PDU test runs monitored and reported were: Hygas Tests 85 and 86; BI-GAS Tests G-11C, 11D, 11E, 11F, G-12 and G-12A; Westinghouse test runs TP-023-4, TP-027-1, TP-027-2 and TP-027-3; Exxon test periods 13 through 17; and Rockwell Tests 318-063 through 318-073. Kellogg made significant progress toward completion of the Operating Plan Requirements for the individual developers, and began an evaluation of the Hygas data base. The final report on Westinghouse Risk Analysis were issued. Progress was made in completing the reports of the screening evaluations of Exxon, Rockwell and Westinghouse. The safety assurance study continued, as did normal participation in MPC activities. New task orders for technical/economic studies were submitted for review and approval.

  18. SCALE: A modular code system for performing standardized computer analyses for licensing evaluation: Functional modules, F9-F11

    SciTech Connect (OSTI)

    NONE

    1997-03-01T23:59:59.000Z

    This Manual represents Revision 5 of the user documentation for the modular code system referred to as SCALE. The history of the SCALE code system dates back to 1969 when the current Computational Physics and Engineering Division at Oak Ridge National Laboratory (ORNL) began providing the transportation package certification staff at the U.S. Atomic Energy Commission with computational support in the use of the new KENO code for performing criticality safety assessments with the statistical Monte Carlo method. From 1969 to 1976 the certification staff relied on the ORNL staff to assist them in the correct use of codes and data for criticality, shielding, and heat transfer analyses of transportation packages. However, the certification staff learned that, with only occasional use of the codes, it was difficult to become proficient in performing the calculations often needed for an independent safety review. Thus, shortly after the move of the certification staff to the U.S. Nuclear Regulatory Commission (NRC), the NRC staff proposed the development of an easy-to-use analysis system that provided the technical capabilities of the individual modules with which they were familiar. With this proposal, the concept of the Standardized Computer Analyses for Licensing Evaluation (SCALE) code system was born. This volume consists of the section of the manual dealing with three of the functional modules in the code. Those are the Morse-SGC for the SCALE system, Heating 7.2, and KENO V.a. The manual describes the latest released versions of the codes.

  19. SCALE: A modular code system for performing standardized computer analyses for licensing evaluation: Control modules C4, C6

    SciTech Connect (OSTI)

    NONE

    1997-03-01T23:59:59.000Z

    This Manual represents Revision 5 of the user documentation for the modular code system referred to as SCALE. The history of the SCALE code system dates back to 1969 when the current Computational Physics and Engineering Division at Oak Ridge National Laboratory (ORNL) began providing the transportation package certification staff at the U. S. Atomic Energy Commission with computational support in the use of the new KENO code for performing criticality safety assessments with the statistical Monte Carlo method. From 1969 to 1976 the certification staff relied on the ORNL staff to assist them in the correct use of codes and data for criticality, shielding, and heat transfer analyses of transportation packages. However, the certification staff learned that, with only occasional use of the codes, it was difficult to become proficient in performing the calculations often needed for an independent safety review. Thus, shortly after the move of the certification staff to the U.S. Nuclear Regulatory Commission (NRC), the NRC staff proposed the development of an easy-to-use analysis system that provided the technical capabilities of the individual modules with which they were familiar. With this proposal, the concept of the Standardized Computer Analyses for Licensing Evaluation (SCALE) code system was born. This volume is part of the manual related to the control modules for the newest updated version of this computational package.

  20. Kirkland gets license in hot Philippines area

    SciTech Connect (OSTI)

    Kirkland, A.S.

    1992-08-03T23:59:59.000Z

    This paper reports that Kirkland As, Oslo, has received a geophysical survey and exploration contract (GSEC) in a sizzling exploration and development theater off the Philippines. The license covers about 6,000 sq miles of undisputed waters, with depths mostly less than 300 ft, and lies in the Reed Bank area off Northwest Palawan Island, where several major oil and gas strikes have been made recently. Kirkland has 1 year in which to carry out its seismic work commitment. The terms of the GSEC then give an option to drill one well in a 6 month period. Once the results have been analyzed, the company can either drill another well or enter into a service contract for the license. Kirkland has a 65% share in the license, with the remainder split between Philippine companies Philodrill Corp., Beguet Mining Corp. subsidiary Petrofields, and Seafront Resources Corp. The Philippines is one of Kirkland's main areas of activity, the Kirkland Commercial Manager Ralph Baxter.

  1. Evaluation of using cyclocranes to support drilling & production of oil & gas in wetland areas. Sixth quarterly technical progress report, incorporating milestone schedule/status, October 1993--December 1993

    SciTech Connect (OSTI)

    Eggington, W.J.

    1994-04-01T23:59:59.000Z

    This report is a progress report on a planned program falling under wetlands area research related to drilling, production, and transportation of oil and gas resources. Specifically the planned program addresses an evaluation of using cyclocraft to transport drill rigs, mud, pipes and other materials and equipment in a cost effective and environmentally safe manner to support oil and gas drilling and production operations in wetland areas. During this period, task 5, subscale tests, and task 7, environmental impacts, were completed. Work was continued on task 10, technology transfer, and the preparation of the final report as part of task 11.

  2. Technical and economic assessment of the IGT peat-gasification process. Engineering support services for the DOE/GRI Coal Gasification Research Program

    SciTech Connect (OSTI)

    Bostwick, L.E.; Hubbard, D.A.; Laramore, R.W.; Senules, E.A.; Shah, K.V.

    1981-04-01T23:59:59.000Z

    Kellogg has completed a moderately detailed design and cost estimate of a 250 billion Btu/Day grass-roots SNG plant using the Peatgas process. Results indicate that the cost of SNG would be $4.40/MM Btu, using a cost of $1.50/MM Btu for peat feedstock at 50% moisture. The SNG cost is reasonably competitive with that currently estimated for SNG from coal, and Kellogg would anticipate that capital cost reductions, via design optimization, could reduce the NSG cost to a level which is quite competitive. The cost of peat feedstock is a critical area of concern in evaluating economics of the Peatgas process. The value chosen for the base-case economics ($1.50/MM Btu) is in the higher portion of the price range considered typical by most investigators; the price of $1.50/MM Btu was chosen arbitrarily to represent a 50% increase over the cost of coal ($1.00/MM Btu) used by Kellogg in parallel studies, to reflect higher costs for land use and reclamation and for harvesting and dewatering of peat. In a study concurrent with that reported here, Kellogg found that one method of wet harvesting and mechanical/thermal dewatering yields a peat (50% moisture) cost which is unfavorably high and was therefore rejected for use as a base-case cost since much cheaper feedstock is apparently available by other harvesting/dewatering methods. The base-case cost of SNG is moderate somewhat by the values placed on the benzene and oil coproducts (i.e., $1.10 and $0.75 per gallon, respectively). The total of such credits amounts to about 39% of the gross operating cost; a reduction in value of the coproducts would adversely affect the cost of SNG. Certain technical factors are discussed: materials handling problems, high reactivity, low sulfur content, and limited gasification data.

  3. Evaluation of using cyclocranes to support drilling and production of oil and gas in wetland areas. Fifth quarterly technical progress report, Third quarter, 1993

    SciTech Connect (OSTI)

    Eggington, W.J.

    1993-12-31T23:59:59.000Z

    The planned program falls under wetlands area research related to drilling, production, and transportation of oil and gas resources. Specifically the planned program addresses an evaluation of using cyclocraft to transport drill rigs, mud, pipes and other materials and equipment in a cost effective and environmentally safe manner to support oil and gas drilling and production operations in wetland areas. The cyclocraft is a proven hybrid aircraft that utilizes aerostatic and aerodynamic lift. This type of aircraft has considerable payload capacity, VTOL capability, high controllability, low operating cost, low downwash and high safety. The benefits of using a cyclocraft to transport drill rigs and materials over environmentally-sensitive surfaces would be significant. The cyclocraft has considerable cost and operational advantages over the helicopter. In 1992, Task 1, Environmental Considerations, and Task 2, Transport Requirements, were completed. In the first two quarters of 1993, Task 3, Parametric Analysis, Task 4, Preliminary Design, and Task 6, Ground Support, were completed. Individual reports containing results obtained from each of these tasks were submitted to DOE. In addition, through June 30, 1993, a Subscale Test Plan was prepared under Task 5, Subscale Tests, and work was initiated on Task 7, Environmental Impacts, Task 8, Development Plan, Task 9, Operating Costs, and Task 10, Technology Transfer.

  4. Strategic Basis for License Application Planning for a Potential Yucca Mountain Repository

    SciTech Connect (OSTI)

    Newberry, C. M.; Brocoum, S. J.; Gamble, R. P.; Murray, R. C.; Cline, M.

    2002-02-26T23:59:59.000Z

    If Yucca Mountain, Nevada is designated as the site for development of a geologic repository for disposal of spent nuclear fuel and high-level radioactive waste, the Department of Energy (DOE) must obtain Nuclear Regulatory Commission (NRC) approval first for repository construction, then for an operating license, and, eventually, for repository closure and decommissioning. The licensing criteria defined in Code of Federal Regulations, Title 10, Part 63 (10 CFR Part 63) establish the basis for these NRC decisions. Submittal of a license application (LA) to the NRC for authorization to construct a repository at the Yucca Mountain site is, at this point, only a potential future action by the DOE. The policy process defined in the Nuclear Waste Policy Act (NWPA), as amended, for recommendation and designation of Yucca Mountain as a repository site makes it difficult to predict whether or when the site might be designated. The DOE may only submit a LA to the NRC if the site designation takes effect. In spite of this uncertainty, the DOE must take prudent and appropriate action now, and over the next several years, to prepare for development and timely submittal of a LA. This is particularly true given the need for the DOE to develop, load, and certify the operation of its electronic information system to provide access to its relevant records as part of the licensing support network (LSN) in compliance with NRC requirements six months prior to LA submittal. The DOE must also develop a LA, which is a substantially different document from those developed to support a Site Recommendation (SR) decision. The LA must satisfy NRC licensing criteria and content requirements, and address the acceptance criteria defined by the NRC in its forthcoming Yucca Mountain Review Plan (YMRP). The content of the LA must be adequate to facilitate NRC acceptance and docketing for review, and the LA and its supporting documents must provide the documented basis for the NR C findings required for a construction authorization. The LA must also support a licensing proceeding before an Atomic Safety and Licensing Board panel prior to NRC action on any decision to authorize construction. The DOE has established a strategic basis for planning that is intended to provide the framework for development of an integrated plan for activities leading to preparation and submittal of a LA.

  5. Open Science: Open source licenses in scientific research 

    E-Print Network [OSTI]

    Guadamuz, Andres

    2006-01-01T23:59:59.000Z

    The article examines the validity of OSS (open source software) licenses for scientific, as opposed to creative works. It draws on examples of OSS licenses to consider their suitability for the scientific community and ...

  6. Slide11 | OSTI, US Dept of Energy, Office of Scientific and Technical...

    Office of Scientific and Technical Information (OSTI)

    principals * Administration provided by Chair(s) selected from Alliance * Technical team provides technical direction and recommendations * Major support provided by CENDI *...

  7. Slide09 | OSTI, US Dept of Energy, Office of Scientific and Technical...

    Office of Scientific and Technical Information (OSTI)

    principals * Administration provided by Chair(s) selected from Alliance * Technical team provided original technical direction and recommendations * Major support provided by...

  8. Sustainable energy for all. Technical report of task force 1 in support of the objective to achieve universal access to modern energy services by 2030

    SciTech Connect (OSTI)

    Birol, Fatih [International Energy Agency, Paris (France); Brew-Hammond, Abeeku (University of Science and Technology (Ghana

    2012-04-15T23:59:59.000Z

    The UN Secretary General established the Sustainable Energy for All initiative in order to guide and support efforts to achieve universal access to modern energy, rapidly increase energy efficiency, and expand the use of renewable energies. Task forces were formed involving prominent energy leaders and experts from business, government, academia and civil society worldwide. The goal of the Task Forces is to inform the implementation of the initiative by identifying challenges and opportunities for achieving its objectives. This report contains the findings of Task Force One which is dedicated to the objective of achieving universal access to modern energy services by 2030. The report shows that universal energy access can be realized by 2030 with strong, focused actions set within a coordinated framework.

  9. Social License and Environment Protection: Why Businesses Go Beyond Compliance

    E-Print Network [OSTI]

    Gunningham, Neil; Kagan, Robert A.; Thornton, Dorothy

    2002-01-01T23:59:59.000Z

    financial analysts -- the economic license does not encourage a firm to invest in very costly environmental measures or technologies

  10. Engineering support services for the DOE/GRI coal-gasification research program. Monthly technical progress report, 22 August - 25 September, 1981

    SciTech Connect (OSTI)

    Bostwick, L.E.; Ethridge, T.R.; Starr, D.W.; Hubbard, D.A.; Koneru, P.B.; Smith, M.R.; Ward, W.E.; Wong, E.W.

    1982-01-01T23:59:59.000Z

    The objective of this contract is to provide engineering support services to the Department of Energy/Gas Research Institute in the high Btu coal gasification research program. The gasification research program is to determine the specific process and/or combination of component processing steps that offer the greatest economic potential for commercial application. During September, Kellogg continued active monitoring of operations at Westinghouse, IGT, Peatgas, and BI-GAS. Efforts relative to Hygas, Rockwell, Exxon and Bell were minimal. Test runs monitored and reported here are BI-GAS tests 17E and 17F, Westinghouse PDU test TP-028-3, and IGT Peatgas test 3. Kellog attended meetings on 1 and 22 September to discuss the review of the Hygas final report. Comments on Kellogg's draft report on the Hygas data base evaluation were received. Kellogg's evaluations of PDU operating data from Westinghouse and Exxon continues. The Kellogg report on Peatgas PDU data base evaluation was issued in draft form. At DOE's request, Kellogg began work on an evaluation of the existing data base (by IGT) for single-stage gasification of peat. Work on the descriptive brochure continued, aimed toward issue of a draft in the near future. Kellogg also provided input regarding Westinghouse test runs to a DOE consultant.

  11. Technical basis for storage of Zircaloy-clad spent fuel in inert gases

    SciTech Connect (OSTI)

    Johnson, A.B. Jr.; Gilbert, E.R.

    1983-09-01T23:59:59.000Z

    This report summarizes the technical bases to establish safe conditions for dry storage of Zircaloy-clad fuel. Dry storage of fuel with zirconium alloy cladding has been licensed in Canada, the Federal Republic of Germany, and Switzerland. In addition, dry storage demonstrations, hot cell tests, and modeling have been conducted using Zircaloy-clad fuel. The demonstrations have included irradiated boiling water reactor, pressurized heavy-water reactor, and pressurized water reactor (PWR) fuel assemblies. Irradiated fuel has been emplaced in and retrieved from metal casks, dry wells, silos, and a vault. Dry storage tests and demonstrations have involved {similar_to}5,000 fuel rods, and {similar_to}600 rods have been monitored during dry storage in inert gases with maximum cladding temperatures ranging from 50 to 570{sup 0}C. Although some tests and demonstrations are still in progress, there is currently no evidence that any rods exposed to inert gases have failed (one PWR rod exposed to an air cover gas failed at {similar_to}70{sup 0}C). Based on this favorable experience, it is concluded that there is sufficient information on fuel rod behavior, storage conditions, and potential cladding failure mechanisms to support licensing of dry storage in the United States. This licensing position includes a requirement for inert cover gases and a maximum cladding temperature guideline of 380{sup 0}C for Zircaloy-clad fuel. Using an inert cover gas assures that even if fuel with cladding defects were placed in dry storage, or if defects develop during storage, the defects would not propagate. Tests and demonstrations involving Zircaloy-clad rods and assemblies with maximum cladding temperatures above 400{sup 0}C are in progress. When the results from these tests have been evaluated, the viability of higher temperature limits should be examined. Acceptable conditions for storage in air and dry storage of consolidated fuel are issues yet to be resolved.

  12. SUMMARY OF AVC/H.264 LICENSE TERMS1 The AVC Patent Portfolio License is divided into two principal parts (see Diagram): (a)

    E-Print Network [OSTI]

    Rodriguez, Carlos

    SUMMARY OF AVC/H.264 LICENSE TERMS1 The AVC Patent Portfolio License is divided into two principal and may not be relied upon for any purpose. The AVC Patent Portfolio License provides the actual terms of license on which users may rely. 2 Sections 2.1 and 2.6 of the AVC Patent Portfolio License 3 Sections 2

  13. Honda Transmission Technical Center

    High Performance Buildings Database

    Russells Point, OH The Honda Transmission Technical Center is located on the Honda of America Manufacturing Plant facility site in Russells Point, Ohio. This facility is used for product engineering and market quality testing and analysis of automatic transmissions. The building contains a large workshop area for ten cars, a future dynamometer, two laboratories, an open office area, three conference rooms, a break room, restrooms, and related support areas.

  14. Technical planning activity: Final report

    SciTech Connect (OSTI)

    Not Available

    1987-01-01T23:59:59.000Z

    In April 1985, the US Department of Energy's (DOE's) Office of Fusion Energy commissioned the Technical Planning Activity (TPA). The purpose of this activity was to develop a technical planning methodology and prepare technical plans in support of the strategic and policy framework of the Magnetic Fusion Program Plan issued by DOE in February 1985. Although this report represents the views of only the US magnetic fusion community, it is international in scope in the sense that the technical plans contained herein describe the full scope of the tasks that are prerequisites for the commercialization of fusion energy. The TPA has developed a well-structured methodology that includes detailed definitions of technical issues, definitions of program areas and elements, statements of research and development objectives, identification of key decision points and milestones, and descriptions of facility requirements.

  15. EPA's Financial and Technical Resources

    E-Print Network [OSTI]

    Perea, S. M.

    2011-01-01T23:59:59.000Z

    EPA?s Financial and Technical Resources Suzanna M. Perea, EPA Region VI CATEE Conference November 9, 2011 EPA?s Primary Role Where and how communities are built has a major impact on the environment and on public health. Many programs... are aimed at supporting activities that build more sustainable communities. Protecting Human Health and the Environment Smart Growth Implementation Assistance (SGIA) Grants http://www.epa.gov/smartgrowth/sgia.htm Building Blocks Technical...

  16. Technical Assessment Team (TAT) Supporting Technical Documents | Department

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn April 23,EnergyChicopee ElectricCommunity-Based EnergyNWSmallTaxUniversityTheof

  17. Licensing and {open_quotes}CRADA`s{close_quotes} in Oak Ridge technology transfer

    SciTech Connect (OSTI)

    Prosser, G.A.

    1993-10-01T23:59:59.000Z

    In the belief that effective technology transfer is a ``contact sport,`` Martin Marietta Energy Systems (Energy Systems), the Department of Energy`s (DOE`s) management contractor in Oak Ridge, Tennessee, encourages its research and engineering employees to directly interact with their commercial-sector counterparts. Over the years, relationships which have been initiated through such technical interactions have led to many of the patent licenses ad cooperative research and development agreements (CRADAs) which currently exist among Energy Systems, US companies, universities, and industrial consortia. The responsibility for creating and implementing Energy Systems policies and procedures to accomplish DOE`s technology transfer objectives in Oak Ridge lies with the Office of Technology Transfer (OTT). In addition, licensing executives within OTT are responsible for negotiating the terms and conditions of patent licenses and CRADAs for the commercialization of government-funded technologies and research expertise. Other technology transfer initiatives in Oak Ridge help companies in a wide range of industries overcome manufacturing obstacles, enabling them to retain existing jobs and to create new business opportunities.

  18. PRELIMINARY TECHNICAL SUPPORT ENERGY EFFICIENCY PROGRAM

    E-Print Network [OSTI]

    ......................................................................ES-4 ES.3.1 Market and Technology Assessment Office of Energy Efficiency and Renewable Energy Building Technologies Program Appliances and Commercial

  19. Technical Support Document: Energy Conservation Standards for

    Broader source: Energy.gov (indexed) [DOE]

    fuel burning is considered an environmental hazard because it contributes to the "greenhouse effect" by trap- ping heat from the sun that has been absorbed by the Earth and emitted...

  20. TECHNICAL SUPPORT DOCUMENT: ENERGY CONSERVATION STANDARDS FOR...

    Broader source: Energy.gov (indexed) [DOE]

    of heat near the Earth's surface. This trapping of heat, referred t o as the "greenhouse effect", raises the mean global temperature. Because of human activity, the C 0 2...

  1. Technical support for combustion 2000 program

    SciTech Connect (OSTI)

    Ahluwalia, R.K.; Im, K.H.; Natesan, K.; Livengood, C.D.; Schmalzer, D.K.

    1993-07-01T23:59:59.000Z

    The high-temperature advanced furnace (HITAF) is an important component of the high-performance power system (HIPPS) being developed in the Combustion 2000 program. The purpose of HITAF is to raise superheated steam for the Rankin cycle and to heat the clean working fluid (air) to 1,800-2,400{degree}F for the Brayton cycle. Analytical and experimental investigations are being carried out to design, analyze and assess different concepts for high temperature advanced furnaces capable of heating compressed air to 1,800-2,400{degree}F; to evaluate performance of metallic and ceramic materials for service at elevated temperatures in HITAF environment; and to conduct critical, systems-oriented evaluations of advanced flue-gas cleanup (FGC) technologies appropriate to the low-emission-boiler systems (LEBS).

  2. ALARA Training for Technical Support Personnel

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742Energy China 2015ofDepartmentDepartment of

  3. ATVM Technical Support Document | Department of Energy

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directed off Energy.gov. Are you0 ARRA Newsletters 2010 ARRAAATTACHMENTfLASH2011-6(2)-OPAMATVM FAQs

  4. Supporting Technical Documents | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn April 23, 2014,Zaleski -BlueprintThis document detailsEnergyIn the fall of

  5. University of Toronto Department of Computer Science 2012 Steve Easterbrook. This presentation is available free for non-commercial use with attribution under a creative commons license. 1

    E-Print Network [OSTI]

    Easterbrook, Steve

    free for non-commercial use with attribution under a creative commons license. 5 Tool 1: Work Breakdown" releases" #12;2 University of Toronto Department of Computer Science © 2012 Steve Easterbrook Structure" 1.1 Software Systems Engineering" 1.1.1 Support to Systems Engineering" 1.1.2 Support to Hardware

  6. Title 18 CFR 4 Licenses, Permits, Exemptions, and Determination...

    Open Energy Info (EERE)

    Title 18 CFR 4 Licenses, Permits, Exemptions, and Determination of Project Costs Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document-...

  7. FERC Handbook for Hydroelectric Project Licensing and 5 MW Exemptions...

    Open Energy Info (EERE)

    GuidanceGuideHandbook Abstract This handbook outlines the requirements for hydropower licenses issued by the Federal Energy Regulatory Commission. Author Federal Energy...

  8. Vermont Permit and License Information: NPDES Stormwater General...

    Open Energy Info (EERE)

    SitesLegal Abstract Permit and licensing information for Clean Water Act 304 National Pollution Discharge Elimination System (NPDES) Permits for general construction. Published NA...

  9. FERC Hydropower Licensing and Endangered Species - A Guide for...

    Open Energy Info (EERE)

    Energy Regulatory Commission. 2001. FERC Hydropower Licensing and Endangered Species - A Guide for Applicants, Contractors, and Staff. Federal Energy Regulatory Commission....

  10. Guidelines to Consider for Participating in the Alternative Licensing...

    Open Energy Info (EERE)

    Guidelines to Consider for Participating in the Alternative Licensing Process Jump to: navigation, search OpenEI Reference LibraryAdd to library PermittingRegulatory Guidance -...

  11. Y-12 cleaning technology licensed by Knoxville engineering firm...

    National Nuclear Security Administration (NNSA)

    cleaning technology licensed by Knoxville engineering firm | National Nuclear Security Administration Facebook Twitter Youtube Flickr RSS People Mission Managing the Stockpile...

  12. Argonne announces new licensing agreement with AKHAN Semiconductor...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Argonne announces new licensing agreement with AKHAN Semiconductor By Jared Sagoff * November 19, 2014 Tweet EmailPrint ARGONNE, Ill. - The U.S. Department of Energy's (DOE)...

  13. Water Resources Center Annual Technical Report

    E-Print Network [OSTI]

    Water Resources Center Annual Technical Report FY 2007 Water Resources Center Annual Technical Report FY 2007 1 #12;Introduction The Rhode Island Water Resources Center has supported one information transfer project, "Clean Drinking Water in Rhode Island" and one research project "Enhancing Drinking Water

  14. Waste transfer leaks technical basis document

    SciTech Connect (OSTI)

    ZIMMERMAN, B.D.

    2003-03-22T23:59:59.000Z

    This document provides technical support for the onsite radiological and toxicological, and offsite toxicological, portions of the waste transfer leak accident presented in the Documented Safety Analysis. It provides the technical basis for frequency and consequence bin selection, and selection of safety SSCs and TSRs.

  15. 21st Century Truck Partnership - Roadmap and Technical White...

    Broader source: Energy.gov (indexed) [DOE]

    Appendix containing supporting information to the 21st Century Partnership's Roadmap and Technical White Papers (21CTP-003). 21ctproadmapappendix2007.pdf More Documents &...

  16. Advanced Reactor Licensing: Experience with Digital I&C Technology in Evolutionary Plants

    SciTech Connect (OSTI)

    Wood, RT

    2004-09-27T23:59:59.000Z

    This report presents the findings from a study of experience with digital instrumentation and controls (I&C) technology in evolutionary nuclear power plants. In particular, this study evaluated regulatory approaches employed by the international nuclear power community for licensing advanced l&C systems and identified lessons learned. The report (1) gives an overview of the modern l&C technologies employed at numerous evolutionary nuclear power plants, (2) identifies performance experience derived from those applications, (3) discusses regulatory processes employed and issues that have arisen, (4) captures lessons learned from performance and regulatory experience, (5) suggests anticipated issues that may arise from international near-term deployment of reactor concepts, and (6) offers conclusions and recommendations for potential activities to support advanced reactor licensing in the United States.

  17. Land Use License | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere I Geothermal Pwer Plant Jump to: navigation,working-groupsIllinois:LakeIowa:LambdaNew York:Texas:LicenseLegal

  18. NRC Licensing Strategy Development for the NGNP

    SciTech Connect (OSTI)

    Mark R. Holbrook; Trevor Cook

    2008-09-01T23:59:59.000Z

    The Next Generation Nuclear Plant (NGNP) project will provide the basis for commercialization of a new generation of advanced nuclear plants that utilize hightemperature gas-cooled reactor (HTGR) technology. The inherently safe HTGR design characteristics can be utilized to supply high-temperature process heat, co-generated electricity, and/or hydrogen for a number of industrial applications (e.g., petrochemical processes). Completion of the NGNP will result in a facility that demonstrates the safety and economics of the design, the commercial industrial potential of the technology, and the viability of the licensing strategy.

  19. FERC Licensing Processes Matrix | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are beingZealand JumpConceptual Model,DOEHazelPennsylvania: EnergyExolis Energy JumpFAC 04-08 JumpLicensing Processes

  20. Licensing Technologies | Y-12 National Security Complex

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHigh SchoolIn12electron 9 5Let us count the ways.ICRUOpportunityLicensing

  1. Property:FERC License | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are beingZealand Jump to:Ezfeedflag Jump to: navigation, search Property Name Ezfeedflag Property Type BooleanLicense

  2. TTWG Licensing Guide | Department of Energy

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directed offOCHCO Overview OCHCOSystems Analysis Success Stories Systems AnalysisTESTIMONYTTWG Licensing

  3. Technologies Available for Licensing | Partnerships | ORNL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of ScienceandMesa del SolStrengthening a solidSynthesis of 2D AlloysTrails NewsTechnology Licensing How

  4. Technical requirements specification for tank waste retrieval

    SciTech Connect (OSTI)

    Lamberd, D.L.

    1996-09-26T23:59:59.000Z

    This document provides the technical requirements specification for the retrieval of waste from the underground storage tanks at the Hanford Site. All activities covered by this scope are conducted in support of the Tank Waste Remediation System (TWRS) mission.

  5. Technical Brief

    E-Print Network [OSTI]

    Depleted Uranium; Brian Littleton

    2006-01-01T23:59:59.000Z

    ii iiiFOREWARD The Depleted Uranium Technical Brief is designed to convey available information and knowledge about depleted uranium to EPA Remedial Project Managers, On-Scene Coordinators, contractors, and other Agency managers involved with the remediation of sites contaminated with this material. It addresses relative questions regarding the chemical and radiological health concerns involved with depleted uranium in the environment. This technical brief was developed to address the common misconception that depleted uranium represents only a radiological health hazard. It provides accepted data and references to additional sources for both the radiological and chemical characteristics, health risk as well as references for both the monitoring and measurement and applicable treatment techniques for depleted uranium. Please Note: This document has been changed from the original publication dated

  6. SCALE: A modular code system for performing standardized computer analyses for licensing evaluation: Functional modules F1-F8

    SciTech Connect (OSTI)

    NONE

    1997-03-01T23:59:59.000Z

    This Manual represents Revision 5 of the user documentation for the modular code system referred to as SCALE. The history of the SCALE code system dates back to 1969 when the current Computational Physics and Engineering Division at Oak Ridge National Laboratory (ORNL) began providing the transportation package certification staff at the U.S. Atomic Energy Commission with computational support in the use of the new KENO code for performing criticality safety assessments with the statistical Monte Carlo method. From 1969 to 1976 the certification staff relied on the ORNL staff to assist them in the correct use of codes and data for criticality, shielding, and heat transfer analyses of transportation packages. However, the certification staff learned that, with only occasional use of the codes, it was difficult to become proficient in performing the calculations often needed for an independent safety review. Thus, shortly after the move of the certification staff to the U.S. Nuclear Regulatory Commission (NRC), the NRC staff proposed the development of an easy-to-use analysis system that provided the technical capabilities of the individual modules with which they were familiar. With this proposal, the concept of the Standardized Computer Analyses for Licensing Evaluation (SCALE) code system was born. This volume consists of the section of the manual dealing with eight of the functional modules in the code. Those are: BONAMI - resonance self-shielding by the Bondarenko method; NITAWL-II - SCALE system module for performing resonance shielding and working library production; XSDRNPM - a one-dimensional discrete-ordinates code for transport analysis; XSDOSE - a module for calculating fluxes and dose rates at points outside a shield; KENO IV/S - an improved monte carlo criticality program; COUPLE; ORIGEN-S - SCALE system module to calculate fuel depletion, actinide transmutation, fission product buildup and decay, and associated radiation source terms; ICE.

  7. Facility worker technical basis document

    SciTech Connect (OSTI)

    EVANS, C.B.

    2003-03-21T23:59:59.000Z

    This report documents the technical basis for facility worker safety to support the Tank Farms Documented Safety Analysis and described the criteria and methodology for allocating controls to hazardous conditions with significant facility worker consequences and presents the results of the allocation.

  8. CUNY EXPORT CONTROL PROCEDURES 12. Licensed Software Programs

    E-Print Network [OSTI]

    Rosen, Jay

    CUNY EXPORT CONTROL PROCEDURES 12. Licensed Software Programs This section addresses the export control implications of licensing a software product that has been identified as "export controlled as "export controlled." In such cases and for purposes of understanding access implications for CUNY

  9. Technology Available for Licensing Office of Technology Management

    E-Print Network [OSTI]

    Lee, Dongwon

    Technology Available for Licensing Office of Technology Management The Pennsylvania State University 113 Technology Center, University Park, PA 16802 814.865.6277 phone; 814.865.3591 fax Contact: Matthew D. Smith Sr. Technology Licensing Officer The Pennsylvania State University Phone: (814) 863

  10. Patent License for OpenSSL 1. Definitions

    E-Print Network [OSTI]

    Rogaway, Phillip

    Patent License for OpenSSL 1. Definitions 1.1 "Licensor" means Phillip Rogaway. orOne Shields Avenue, Davis, CA 95616-8562. 1.2 "Licensed Patents" means any patent that claims priority to United States Patent Application No. 09/918,615 entitled "Method and Apparatus for Facilitating Efficient

  11. Non-exclusive License: AGMT-XXXX U.S. DEPARTMENT OF ENERGY NATIONAL...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    for the computation of any royalty fees payable under this License, and shall render to LICENSOR annually, within thirty days of the anniversary date of this License, an...

  12. Exclusive License: AGMT-XXXX U.S. DEPARTMENT OF ENERGY NATIONAL...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    for the computation of any royalty fees payable under this License, and shall render to LICENSOR annually, within thirty days of the anniversary date of this License, an...

  13. Technical information

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 111 1,613 122 40Coal StocksProvedFeet)ThousandNumber andCrude StreamCrudeTechnical

  14. Technical Sessions

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What'sis Taking Over Our InstagramStructureProposedPAGESafety Tag:8,, 20153 To synchronizeTechnical

  15. FLAMMABLE GAS TECHNICAL BASIS DOCUMENT

    SciTech Connect (OSTI)

    KRIPPS, L.J.

    2003-10-09T23:59:59.000Z

    This technical basis document was developed to support of the Tank Farms Documented Safety Analysis (DSA) and describes the risk binning process for the flammable gas representative accidents and associated represented hazardous conditions. The purpose of the risk binning process is to determine the need for safety-significant structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls for a given representative accident or represented hazardous condition based on an evaluation of the event frequency and consequence. Note that the risk binning process is not applied to facility workers, because all facility worker hazardous conditions are considered for safety-significant SSC and/or TSR-level controls.

  16. Coordinating NRC License Closure/Termination and Army Corps of Engineers FUSRAP Cleanups

    SciTech Connect (OSTI)

    Walter, N. [MACTEC, 511 Congress Street, Portland, ME 04101 (United States); Greene, D. R. [LeBoeuf, Lamb, Greene and MacRae LLP, 225 Asylum Street, Hartford, CT 06103 (United States); Knauerhase, R. K. [Combustion Engineering, 2000 Day Hill Road, CEP 5580-2207, Windsor, CT 06095 (United States)

    2006-07-01T23:59:59.000Z

    Overlapping regulatory cleanup programs present a significant challenge for business entities seeking to close and redevelop properties in an environmentally-appropriate but cost-effective manner. In the nuclear decontamination context, this challenge has been recognized in Memoranda of Understanding ('MOUs') between regulators with overlapping responsibilities seeking to minimize duplicative efforts/costs while fulfilling their respective regulatory obligations. For instance, an MOU between the Army Corps of Engineers (the 'Corps') and the Nuclear Regulatory Commission ('NRC') for coordinating Corps' cleanups under the Formerly Utilized Sites Remedial Action Program ('FUSRAP') and NRC D and D to close and terminate an NRC license was reached in July 2001. Similarly, U.S. Environmental Protection Agency ('EPA') and NRC entered into an MOU in October 2002 addressing the interaction between NRC decontamination and decommissioning ('D and D') oversight and EPA's authority under the Comprehensive Environmental Response, Compensation and Liability Act ('CERCLA') at NRC-licensed sites. Yet, despite these MOU agreements, the simultaneous application of different regulatory programs, differing perspectives on their respective objectives and limited experience in addressing such circumstances often can lead to issues that demand creative solutions. This paper examines the interplay of these regulatory programs, the MOU of the agencies seeking to address their responsibilities under them and the coordination of the cleanups and license closure/termination process under the programs. It also offers technical and practical suggestions and insight to cost-effectively manage such efforts based on experiences with these programs and the regulators and stakeholders involved (at the federal, state and local levels). (authors)

  17. FLAMMABLE GAS TECHNICAL BASIS DOCUMENT

    SciTech Connect (OSTI)

    KRIPPS, L.J.

    2005-03-03T23:59:59.000Z

    This document describes the qualitative evaluation of frequency and consequences for DST and SST representative flammable gas accidents and associated hazardous conditions without controls. The evaluation indicated that safety-significant structures, systems and components (SSCs) and/or technical safety requirements (TSRs) were required to prevent or mitigate flammable gas accidents. Discussion on the resulting control decisions is included. This technical basis document was developed to support WP-13033, Tank Farms Documented Safety Analysis (DSA), and describes the risk binning process for the flammable gas representative accidents and associated represented hazardous conditions. The purpose of the risk binning process is to determine the need for safety-significant structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls for a given representative accident or represented hazardous condition based on an evaluation of the event frequency and consequence.

  18. Organic solvent technical basis document

    SciTech Connect (OSTI)

    SANDGREN, K.R.

    2003-03-22T23:59:59.000Z

    This technical basis document was developed to support the Tank Farms Documented Safety Analysis (DSA), and describes the risk binning process and the technical basis for assigning risk bins for the organic solvent fire representative and associated represented hazardous conditions. The purpose of the risk binning process is to determine the need for safety-significant structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls for a given representative accident or represented hazardous conditions based on an evaluation of the frequency and consequence. Note that the risk binning process is not applied to facility workers, because all facility worker hazardous conditions are considered for safety-significant SSCs and/or TSR-level controls. Determination of the need for safety-class SSCs was performed in accordance with DOE-STD-3009-94, Preparation Guide for US Department of Energy Nonreactor Nuclear Facility Documented Safety Analyses, as described in this report.

  19. Technical Report 20061 COASTAL HABITATS IN

    E-Print Network [OSTI]

    Technical Report 2006­1 COASTAL HABITATS IN PUGET SOUND: A Research Plan in Support of the Puget Sound Nearshore Partnership Prepared in support of the Puget Sound Nearshore Partnership November 2006 Logsdon, University of Washington Doug Myers, Puget Sound Action Team Jan Newton, University of Washington

  20. Development of Regulatory Technical Requirements for the Advanced Integral Type Research Reactor

    SciTech Connect (OSTI)

    Jo, Jong Chull; Yune, Young Gill; Kim, Woong Sik; Kim, Hho Jung [Korea Institute of Nuclear Safety, 19 Kusung-dong, Yusung-ku, Taejon, 305-338 (Korea, Republic of)

    2004-07-01T23:59:59.000Z

    This paper presents the current status of the study on the development of regulatory technical requirements for the licensing review of an advanced integral type research reactor of which the license application is expected in a few years. According to the Atomic Energy Act of Korea, both research and education reactors are subject to the technical requirements for power reactors in the licensing review. But, some of the requirements may not be applicable or insufficient for the licensing reviews of reactors with unique design features. Thus it is necessary to identify which review topics or areas can not be addressed by the existing requirements and to develop the required ones newly or supplement appropriately. Through the study performed so far, it has been identified that the following requirements need to be developed newly for the licensing review of SMART-P: the use of proven technology, the interfacial facility, the non-safety systems, and the metallic fuels. The approach and basis for the development of each of the requirements are discussed. (authors)

  1. Air Risk Information Support Center

    SciTech Connect (OSTI)

    Shoaf, C.R.; Guth, D.J. [Environmental Protection Agency, Washington, DC (United States)

    1990-12-31T23:59:59.000Z

    The Air Risk Information Support Center (Air RISC) was initiated in early 1988 by the US Environmental Protection Agency`s (EPA) Office of Health and Environmental Assessment (OHEA) and the Office of Air Quality Planning and Standards (OAQPS) as a technology transfer effort that would focus on providing information to state and local environmental agencies and to EPA Regional Offices in the areas of health, risk, and exposure assessment for toxic air pollutants. Technical information is fostered and disseminated by Air RISCs three primary activities: (1) a {open_quotes}hotline{close_quotes}, (2) quick turn-around technical assistance projects, and (3) general technical guidance projects. 1 ref., 2 figs.

  2. Office for Analysis and Evaluation of Operational Data 1996 annual report. Volume 10, Number 3: Technical training

    SciTech Connect (OSTI)

    NONE

    1997-12-01T23:59:59.000Z

    This annual report of the US Nuclear Regulatory Commission`s Office for Analysis and Evaluation of Operational Data (AEOD) describes activities conducted during 1996. The report is published in three parts. NUREG-1272, Vol. 10, No. 1, covers power reactors and presents an overview of the operating experience of the nuclear power industry from the NRC perspective, including comments about trends of some key performance measures. The report also includes the principal findings and issues identified in AEOD studies over the past year and summarizes information from such sources as licensee event reports and reports to the NRC`s Operations Center. NUREG-1272, Vol. 10, No. 2, covers nuclear materials and presents a review of the events and concerns during 1996 associated with the use of licensed material in nonreactor applications, such as personnel overexposures and medical misadministrations. Both reports also contain a discussion of the Incident Investigation Team program and summarize both the Incident Investigation Team and Augmented Inspection Team reports. Each volume contains a list of the AEOD reports issued from CY 1980 through 1996. NUREG-1272, Vol. 10, No. 3, covers technical training and presents the activities of the Technical Training Center in support of the NRC`s mission in 1996.

  3. Technology available for license: Charging of liquid energy storage...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Technology available for license: Charging of liquid energy storage media through radiolysis (ANL-IN-14-036) January 23, 2015 Tweet EmailPrint This technology utilizes radiolysis...

  4. George Mason University Licensed as of 03/2013

    E-Print Network [OSTI]

    /27/2013 2:07:58PM Standard License 4imprint Inc. (49210) PO Box 320 Oshkosh, WI 54903-0320 Mr. John Lord Non-Wool Headwear) Product Categories Advanced Graphic Products dba Advanced-Online (58410) 750

  5. Vertimass licenses ORNL biofuel-to-hydrocarbon conversion technology...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    McCorkle Communications and Media Relations 865.574.7308 Vertimass licenses ORNL biofuel-to-hydrocarbon conversion technology Vertimass LLC, a California-based start-up...

  6. LICENSE HISTORY MO.8 Petrolite Corporation, St. Louis

    Office of Legacy Management (LM)

    et al Multiple. . 70-621, 12-15-61, SNM license for 0.5 kg. of U-235, 93% enriched as a fuel loading and star-up curce for Webster Groves, Missouri reactor. l Discussion:...

  7. Categorization of Used Nuclear Fuel Inventory in Support of a...

    Energy Savers [EERE]

    of Used Nuclear Fuel Inventory in Support of a Comprehensive National Nuclear Fuel Cycle Strategy The Office of Nuclear Energy has conducted a technical review and assessment of...

  8. agile combat support: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Intern Sales and Technical Support Engineer 2052185 (4 Positions) Agilent Technologies wine country, is the R&D headquarters of Agilent's Microwave and Communication Division...

  9. FACILITY WORKER TECHNICAL BASIS DOCUMENT

    SciTech Connect (OSTI)

    SHULTZ, M.V.

    2005-03-31T23:59:59.000Z

    This technical basis document was developed to support RPP-13033, ''Tank Farms Documented Safety Analysis (DSA). It describes the criteria and methodology for allocating controls to hazardous conditions with significant facility worker (FW) consequence and presents the results of the allocation. The criteria and methodology for identifying controls that address FW safety are in accordance with DOE-STD-3009-94, ''Preparation Guide for US Department of Energy Nonreactor Nuclear Facility Documented Safety Analyses''.

  10. Technical Consultant Report Template

    Broader source: Energy.gov [DOE]

    Technical Consultant Report Template, from the Tool Kit Framework: Small Town University Energy Program (STEP).

  11. Document: P1312 Category: Nanotechnology, Physical Science Applications License Status: Available for licensing Texas Industry Cluster: Energy

    E-Print Network [OSTI]

    Lightsey, Glenn

    : Available for licensing Texas Industry Cluster: Energy Scalable methods of producing three-dimensional nanocomposites for energy, semiconductor, and advanced manufacturing applications Problem Currently, the production of nanoparticles and nanostructured films is difficult, because nanoparticles are hard to produce

  12. LLNL 1981: technical horizons

    SciTech Connect (OSTI)

    Not Available

    1981-07-01T23:59:59.000Z

    Research programs at LLNL for 1981 are described in broad terms. In his annual State of the Laboratory address, Director Roger Batzel projected a $481 million operating budget for fiscal year 1982, up nearly 13% from last year. In projects for the Department of Energy and the Department of Defense, the Laboratory applies its technical facilities and capabilities to nuclear weapons design and development and other areas of defense research that include inertial confinement fusion, nonnuclear ordnances, and particle-beam technology. LLNL is also applying its unique experience and capabilities to a variety of projects that will help the nation meet its energy needs in an environmentally acceptable manner. A sampling of recent achievements by LLNL support organizations indicates their diversity. (GHT)

  13. Connecting to Purdue's License Server for ENVI and IDL The license server for IDL and ENVI is: wppapplm01.itap.purdue.edu. The port number is 1700.

    E-Print Network [OSTI]

    Connecting to Purdue's License Server for ENVI and IDL The license server for IDL and ENVI is this information in the environment variables for your computer so that ENVI or IDL can find the license server for the older server with a Variable Value named 1700@wpvappkey01.purdue.edu, change this value to 1700@wppapplm

  14. University of Toronto Department of Computer Science 2004-5 Steve Easterbrook. This presentation is available free for non-commercial use with attribution under a creative commons license. 1

    E-Print Network [OSTI]

    Easterbrook, Steve

    Breakdown Structure 1.1 Software Systems Engineering 1.1.1 Support to Systems Engineering 1.1.2 Support is available free for non-commercial use with attribution under a creative commons license. 5 Tool 1: Work Evaluation 1.2.4 Development facilities and tools Source: Adapted from Blum, 1992, p438 see also: van Vliet

  15. Report of the LANL Fellows Committee on Metrics for the Technical/Business Interface

    E-Print Network [OSTI]

    @lanl.gov, 505-606-1430 Robert Benjamin David Forslund Benjamin Sims (consulting sociologist, CCS-6) 1. Charge of the Technical/Business Interface in supporting technical productivity. Potential ways to collect data

  16. Technical basis for the aboveground structure failure and associated represented hazardous conditions

    SciTech Connect (OSTI)

    GOETZ, T.G.

    2003-07-25T23:59:59.000Z

    This technical basis document describes the risk binning process and the technical basis for assigning risk bins for the aboveground structure failure representative accident and associated represented hazardous conditions. This document was developed to support the documented safety analysis.

  17. University of Toronto Department of Computer Science 2008 Steve Easterbrook. This presentation is available free for non-commercial use with attribution under a creative commons license. 1

    E-Print Network [OSTI]

    Easterbrook, Steve

    commons license. 5 Tool 1: Work Breakdown Structure 1.1 Software Systems Engineering 1.1.1 Support Software 1.2.3.1 Package Evaluation 1.2.4 Development facilities and tools Source: Adapted from Blum, 1992 & Evaluation 1.3.2 End-Product Acceptance Test 1.3.3 Test Bed & Tool Support 1.3.4 Test Data Management 1

  18. License Stewardship Approach to Commercial Nuclear Power Plant Decommissioning

    SciTech Connect (OSTI)

    Daly, P.T.; Hlopak, W.J. [Commercial Services Group, EnergySolutions 1009 Commerce Park, Oak Ridge, TN (United States)

    2008-07-01T23:59:59.000Z

    The paper explores both the conceptual approach to decommissioning commercial nuclear facilities using a license stewardship approach as well as the first commercial application of this approach. The license stewardship approach involves a decommissioning company taking control of a site and the 10 CFR 50 License in order to complete the work utilizing the established trust fund. In conclusion: The license stewardship approach is a novel way to approach the decommissioning of a retired nuclear power plant that offers several key advantages to all parties. For the owner and regulators, it provides assurance that the station will be decommissioned in a safe, timely manner. Ratepayers are assured that the work will be completed for the price they already have paid, with the decommissioning contractor assuming the financial risk of decommissioning. The contractor gains control of the assets and liabilities, the license, and the decommissioning fund. This enables the decommissioning contractor to control their work and eliminates redundant layers of management, while bringing more focus on achieving the desired end state - a restored site. (authors)

  19. Pipeline gas demonstration plant, Phase I. Quarterly technical progress report, December 1980-February 1981

    SciTech Connect (OSTI)

    Eby, R.J.

    1981-03-01T23:59:59.000Z

    Work was performed in the following areas of the Pipeline Gas Demonstration Plant Program: site evaluation and selection; demonstration plant environmental analysis; feedstock plans, licenses, permits and easements; demonstration plant definitive design; construction planning; economic reassessment; technical support; long lead procurement list; and project management. Major work activity continued to be the effort on Demonstration Plant Definitive Design. A Construction Readiness Audit was held on January 14 to 16, 1981 by a Government/Procon team to review the project and assess the readiness of the project to proceed into the construction phase. Documents for the 60% Design Review were prepared for ICGG review and submitted to the Contracting Officer's authorized representative prior to transmittal to the Corps of Engineers for review. The Corps of Engineers conducted a design audit. The primary objective of the audit was to prepare an independent estimate of the work remaining to complete Phase I of the project. Work continued on the production of a single bid package for the Demonstration Plant, suitable for release to a single constructor, and organized so it can be easily broken down into subpackages by construction specialty. A formal audit of the ICGG R/QA Plan and implementation thereof was performed February 11-12, 1981 by the Corps of Engineers. The Contract Deliverable Final Feedstock-Product-Waste Disposal Plan was delivered to the Government on February 25, 1981.

  20. Methodology and assumptions for evaluating heating and cooling energy requirements in new single-family residential buildings: Technical support document for the PEAR (Program for Energy Analysis of Residences) microcomputer program

    SciTech Connect (OSTI)

    Huang, Y.J.; Ritschard, R.; Bull, J.; Byrne, S.; Turiel, I.; Wilson, D.; Hsui, C.; Foley, D.

    1987-01-01T23:59:59.000Z

    This report provides technical documentation for a software package called PEAR (Program for Energy Analysis of Residences) developed by LBL. PEAR offers an easy-to-use and accurate method of estimating the energy savings associated with various energy conservation measures used in site-built, single-family homes. This program was designed for use by non-technical groups such as home builders, home buyers or others in the buildings industry, and developed as an integral part of a set of voluntary guidelines entitled Affordable Housing Through Energy Conservation: A Guide to Designing and Constructing Energy Efficient Homes. These guidelines provide a method for selecting and evaluating cost-effective energy conservation measures based on the energy savings estimated by PEAR. This work is part of a Department of Energy program aimed at conducting research that will improve the energy efficiency of the nation's stock of conventionally-built and manufactured homes, and presenting the results to the public in a simplified format.

  1. Federal Technical Capability Manual

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2004-05-18T23:59:59.000Z

    Provides requirements and responsibilities to ensure recruitment and hiring of technically capable personnel to retain critical technical capabilities within the Department at all times. Cancels DOE M 426.1-1. Canceled by DOE O 426.1.

  2. Radioisotope thermoelectric generator licensed hardware package and certification tests

    SciTech Connect (OSTI)

    Goldmann, L.H.; Averette, H.S. [Westinghouse Hanford Company, P.O. Box 1970, M/S R3-86 or N1-32, Richland, Washington 99352 (United States)

    1995-01-20T23:59:59.000Z

    This paper presents the Licensed Hardware package and the Certification Test portions of the Radioisitope Themoelectric Generator Transportation System. This package has been designed to meet those portions of the {ital Code} {ital of} {ital Federal} {ital Regulations} (10 CFR 71) relating to ``Type B`` shipments of radioactive materials. The licensed hardware is now in the U. S. Department of Energy licensing process that certifies the packaging`s integrity under accident conditions. The detailed information for the anticipated license is presented in the safety analysis report for packaging, which is now in process and undergoing necessary reviews. As part of the licensing process, a full-size Certification Test Article unit, which has modifications slightly different than the Licensed Hardware or production shipping units, is used for testing. Dimensional checks of the Certification Test Article were made at the manufacturing facility. Leak testing and drop testing were done at the 300 Area of the U.S. Department of Energy`s Hanford Site near Richland, Washington. The hardware includes independent double containments to prevent the environmental spread of {sup 238}Pu, impact limiting devices to protect portions of the package from impacts, and thermal insulation to protect the seal areas from excess heat during accident conditions. The package also features electronic feed-throughs to monitor the Radioisotope Thermoelectric Generator`s temperature inside the containment during the shipment cycle. This package is designed to safely dissipate the typical 4,500 thermal watts produced in the largest Radioisotope Thermoelectric Generators. The package also contains provisions to ensure leak tightness when radioactive materials, such as a Radioisotope Thermoelectric Generator for the Cassini Mission, planned for 1997 by the National Aeronautics and Space Administration, are being prepared for shipment. (Abstract Truncated)

  3. FLAMMABLE GAS TECHNICAL BASIS DOCUMENT

    SciTech Connect (OSTI)

    KRIPPS, L.J.

    2005-02-18T23:59:59.000Z

    This document describes the qualitative evaluation of frequency and consequences for double shell tank (DST) and single shell tank (SST) representative flammable gas accidents and associated hazardous conditions without controls. The evaluation indicated that safety-significant SSCs and/or TSRS were required to prevent or mitigate flammable gas accidents. Discussion on the resulting control decisions is included. This technical basis document was developed to support of the Tank Farms Documented Safety Analysis (DSA) and describes the risk binning process for the flammable gas representative accidents and associated represented hazardous conditions. The purpose of the risk binning process is to determine the need for safety-significant structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls for a given representative accident or represented hazardous condition based on an evaluation of the event frequency and consequence.

  4. Federal Technical Capability

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2009-11-19T23:59:59.000Z

    This directive defines requirements and responsibilities for meeting the Department of Energy (DOE) commitment to recruiting, deploying, developing, and retaining a technically competent workforce that will accomplish DOE missions in a safe and efficient manner through the Federal Technical Capability Program (FTCP). Cancels DOE M 426.1-1A, Federal Technical Capability Manual.

  5. Technical Standards Program

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2011-02-23T23:59:59.000Z

    The Order promotes DOE's use of Voluntary Consensus Standards (VCS) as the primary method for application of technical standards and establishes and manages the DOE Technical Standards Program (TSP) including technical standards development, information, activities, issues, and interactions. Admin Chg 1 dated 3-12-13.

  6. Technical Standards Program

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1999-11-19T23:59:59.000Z

    The Technical Standards Program (TSP) promotes the use of voluntary consensus standards by the Department of Energy (DOE), provides DOE with the means to develop needed technical standards, and manages overall technical standards information, activities, issues, and interactions. Cancels DOE O 1300.2A. Canceled by DOE O 252.1A

  7. The use for frequency-consequence curves in future reactor licensing

    E-Print Network [OSTI]

    Debesse, Laurène

    2007-01-01T23:59:59.000Z

    The licensing of nuclear power plants has focused until now on Light Water Reactors and has not incorporated systematically insights and benefits from Probabilistic Risk Assessment (PRA). With the goal of making the licensing ...

  8. Photovoltaics at DOE's National Renewable Energy Laboratory License...

    Energy Savers [EERE]

    Areas Laws & Requirements Reporting & Data Training Project Funding Products & Technologies Technical Assistance Institutional Change Awards Publications Case Studies Tools News...

  9. Emerging information technology and the expanding role of technical communicators

    E-Print Network [OSTI]

    McGuire, Richard Charles

    1996-01-01T23:59:59.000Z

    owners. In particular, Chapter III focuses on functionality that supports the use of document style sheets, document templates, macro programming, and object linking to demonstrate how this functionality expands the role of technical communicators... . . . . . . . . . . . . . . . . . . . . . . . . . . 23 III REDEFINING DOCUMENTS, REDEFINING ROLES . . 26 Style Sheets . Using Templates with Styles . . . . . . . . . . . . . . . How Templates and Style Sheets Redefine the Role of Technical Communicators . . . . . . . . . . . Macros Document...

  10. Technical basis document for natural event hazards

    SciTech Connect (OSTI)

    CARSON, D.M.

    2003-08-28T23:59:59.000Z

    This technical basis document was developed to support the documented safety analysis (DSA) and describes the risk binning process and the technical basis for assigning risk bins for natural event hazard (NEH)-initiated accidents. The purpose of the risk binning process is to determine the need for safety-significant structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls for a given representative accident or represented hazardous conditions based on an evaluation of the frequency and consequence. Note that the risk binning process is not applied to facility workers, because all facility worker hazardous conditions are considered for safety-significant SSCs and/or TSR-level controls This report documents the technical basis for assigning risk bins for Natural Event Hazards Representative Accident and associated represented hazardous conditions.

  11. Implementation Guide for Use in Developing Technical Safety Requirements

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2014-09-08T23:59:59.000Z

    The guide was developed in support of Title 10 Code of Federal Regulations (CFR) Part 830, Nuclear Safety Management. It provides guidance for the requirements defined in 10 CFR §830.205, Technical Safety Requirements.

  12. Computational Analysis of Merchant Marine GPS Data* CASOS Technical Report

    E-Print Network [OSTI]

    Sadeh, Norman M.

    . Keywords: Geospatial analysis, network analysis, clustering * This work was supported in partComputational Analysis of Merchant Marine GPS Data* CASOS Technical Report George B. Davis ISRI - Institute for Software Research International CASOS - Center for Computational Analysis

  13. Technical Analysis of Commodity Markets: Emphasis on Bar Charts 

    E-Print Network [OSTI]

    Purcell, Wayne D.

    1999-07-12T23:59:59.000Z

    Technical analysis of futures markets can be complex, but this publication explains fairly simple methods of using bar charts to predict price trends. Understanding resistance and support planes, chart gaps and other signals can equip producers...

  14. Kentucky Water Resources Research Institute Annual Technical Report

    E-Print Network [OSTI]

    and the Paducah Gaseous Diffusion Plant), the Kentucky Deparmtnet of Military Affairs (Technical Support and cleanup at the Paducah Gaseous Diffusion Plant over the next several years. Five research projects were

  15. Kentucky Water Resources Research Institute Annual Technical Report

    E-Print Network [OSTI]

    ), and the Kentucky River Authority (KRA): 1) Technical Support for the Paducah Gaseous Diffusion Plant (CHS) 2 capability of wetland soils and paleowetland sediments in the vicinity of the Paducah Gaseous Diffusion Plant

  16. Decision Tree for Export Control License Is the article subject to export control regulations?

    E-Print Network [OSTI]

    Hutcheon, James M.

    Decision Tree for Export Control License Is the article subject to export control regulations if further export review is required. Yes Yes Yes Yes No No No No No export requirements Obtain export license No export requirements Obtain export license #12;

  17. Chameleonic Radio Technical Memo No. 1

    E-Print Network [OSTI]

    Ellingson, Steven W.

    Chameleonic Radio Technical Memo No. 1 Prototyping a Software Defined Radio Receiver Based on USRP Defined Radio (SDR) is an emerging technology which supports multi- standard, multi-mode and future proof radio designs. There are several SDR software architectures have been developed during the last few

  18. Oklahoma Water Research Institute Annual Technical Report

    E-Print Network [OSTI]

    Oklahoma Water Research Institute Annual Technical Report FY 2003 Introduction The Environmental Institute at Oklahoma State University has as its mission to serve as a center for stimulation and promotion and sustaining the natural environment. The federally supported Oklahoma Water Resources Research Institute

  19. Technical assistance contractor Management Plan. Final [report

    SciTech Connect (OSTI)

    Not Available

    1993-09-01T23:59:59.000Z

    The Technical Assistance Contractor (TAC) for the Uranium Mill Tailings Remedial Action (UMTRA) Project comprises Jacobs Engineering Group Inc. (JEG) and its major teaming partners [Roy F. Weston, Inc. (RFW), Sergent, Hauskins & Beckwith Agra, Inc. (SHB Agra), and Geraghty & Miller, Inc. (G&M)]. The first three companies have worked together effectively on the UMTRA Project for more than 10 years. With the initiation of the UMTRA Groundwater Project in April 1991, a need arose to increase the TAC`s groundwater technical breadth and depth, so G&M was brought in to augment the team`s capabilities. The TAC contract`s scope is to provide technical, analytical, environmental, engineering, design, inspection, and management support services to the US Department of Energy (DOE) for both surface and groundwater projects. The TAC team continues to support the DOE in completing surface remedial actions and initiating groundwater remediation work for start-up, characterization, design, construction oversight, and remedial operations. A key feature of the TAC`s management approach is the extensive set of communication systems implemented for the UMTRA Project. These systems assist all functional disciplines in performing UMTRA Project tasks associated with management, technical support, administrative support, and financial/project controls.

  20. Financial and Technical Resources The HUD Perspective

    E-Print Network [OSTI]

    Jensen, J.

    2011-01-01T23:59:59.000Z

    Financial and Technical Resources The HUD Perspective U.S. Department of Housing and Urban Development Jerry Jensen, HUD Fort Worth Regional Office CATEE Conference November 9, 2011 Partnership for Sustainable Communities: Livability... Principles 1. Provide more transportation choices. 2. Promote equitable, affordable housing. 3. Enhance economic competitiveness. 4. Support existing communities. 5. Coordinate policies and leverage investment. 6. Value communities and neighborhoods...

  1. Technical basis document for external events

    SciTech Connect (OSTI)

    OBERG, B.D.

    2003-03-22T23:59:59.000Z

    This document supports the Tank Farms Documented Safety Analysis and presents the technical basis for the frequencies of externally initiated accidents. The consequences of externally initiated events are discussed in other documents that correspond to the accident that was caused by the external event. The external events include aircraft crash, vehicle accident, range fire, and rail accident.

  2. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-04/4178-2 2. Government Accession No. 3 of Transportation 16. Abstract Changes in the AASHTO Standard Specifications for Structural Supports for Highway commonly used connection details exhibit poor fatigue performance. This study was initiated to confirm

  3. Water Resources Research Institute Annual Technical Report

    E-Print Network [OSTI]

    Water Resources Research Institute Annual Technical Report FY 2003 Introduction The Idaho Water an autonomous statewide source of support for water research and training without regard to specific topic soils contain appreciable amounts of active clay minerals and exhibit shrink-swell behavior in response

  4. Technical Report Documentation Page 1. Report No.

    E-Print Network [OSTI]

    Texas at Austin, University of

    Technical Report Documentation Page 1. Report No. FHWA/TX-05/0-4079-1 2. Government Accession No. 3 estimation tool developed in Excel, accompanied by a supporting document providing instructions on its Estate, Condemnation Rates, Uniform Act 18. Distribution Statement No restrictions. This document

  5. CUNY EXPORT CONTROL PROCEDURES 5. Licenses and export authorizations

    E-Print Network [OSTI]

    Rosen, Jay

    CUNY EXPORT CONTROL PROCEDURES 5. Licenses and export authorizations This Section addresses how, ITAR items of any kind must not be exported, nor accessed by a non-U.S. person, without proper required depends on the type of export transaction subject to control; for example, temporary versus

  6. Wave Energy Development in Oregon Licensing & Permitting Requirements

    E-Print Network [OSTI]

    July 09 Wave Energy Development in Oregon Licensing & Permitting Requirements Prepared by Pacific Energy Ventures on behalf of the Oregon Wave Energy Trust w w w . o r e g o n w a v e . o r g #12;This study was commissioned by Oregon Wave Energy Trust. Oregon Wave Energy Trust is funded by the Oregon

  7. Choosing intellectual protection: imitation, patent strength and licensing

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Choosing intellectual protection: imitation, patent strength and licensing David Encaoua and Yassine Lefouili March 22, 2006 (revised version) Abstract Patents are probabilistic rights. We set up a multi-stage model in which choosing between patent and trade secrecy is a¤ected by three parameters

  8. License renewal demonstration program: NRC observations and lessons learned

    SciTech Connect (OSTI)

    Prato, R.J.; Kuo, P.T.; Newberry, S.F.

    1996-12-01T23:59:59.000Z

    This report summarizes the Nuclear Regulatory Commission staff`s observations and lessons learned from the five License Renewal Demonstration Program (LRDP) site visits performed by the staff from March 25, 1996, through August 16, 1996. The LRDP was a Nuclear Energy Institute (NEI) program intended to assess the effectiveness of the guidance provided by NEI 95-10, Revision 0, {open_quotes}Industry Guideline for Implementing the Requirements of 10 CFR Part 54 - The License Renewal Rule,{close_quotes} to implement the requirements of Title 10 of the Code of Federal Regulations, Part 54 (10 CFR Part 54), {open_quotes}Requirements for Renewal of Operating Licenses for Nuclear Power Plants.{close_quotes} In general, NEI 95-10 appeared to contain the basic guidance needed for scoping, screening, identifying aging effects, developing aging management programs, and performing time-limited aging analyses. However, inconsistent implementation of this guidance in some areas was an indication that clarification of existing guidance and/or the inclusion-of some new guidance may be needed for applicants to develop a license renewal program that is consistent with the intent of the rule.

  9. Ozone database in support of CMIP5 simulations: results and corresponding

    E-Print Network [OSTI]

    Wirosoetisno, Djoko

    Ozone database in support of CMIP5 simulations: results and corresponding radiative forcing 1234567 Attribution 3.0 License. Atmospheric Chemistry and Physics Ozone database in support of CMIP5 simulations 2011 Abstract. A continuous tropospheric and stratospheric ver- tically resolved ozone time series

  10. Standard technical specifications: Babcock and Wilcox Plants. Revision 1

    SciTech Connect (OSTI)

    NONE

    1995-04-01T23:59:59.000Z

    This report documents the results of the combined effort of the NRC and the industry to produce improved Standard Technical Specifications (STS), Revision 1 for Babcock & Wilcox Plants. The changes reflected in Revision 1 resulted from the experience gained from license amendment applications to convert to these improved STS or to adopt partial improvements to existing technical specifications. This NUREG is the result of extensive public technical meetings and discussions between the Nuclear Regulatory Commission (NRC) staff and various nuclear power plant licensees, Nuclear Steam Supply System (NSSS) Owners Groups, NSSS vendors, and the Nuclear Energy Institute (NEI). The improved STS were developed based on the criteria in the Final Commission Policy Statement on Technical Specifications Improvements for Nuclear Power Reactors, dated July 22, 1993. The improved STS will be used as the basis for individual nuclear power plant licensees to develop improved plant-specific technical specifications. This report contains three volumes. Volume 1 contains the Specifications for all chapters and sections of the improved STS. Volume 2 contains the Bases for Chapters 2.0 and 3.0, and Sections 3.1--3.3 of the improved STS. Volume 3 contains the Bases for Sections 3.4--3.9 of the improved STS.

  11. Final Technical Report

    SciTech Connect (OSTI)

    Stoessel, Chris

    2013-11-13T23:59:59.000Z

    This project developed a new high-performance R-10/high SHGC window design, reviewed market positioning and evaluated manufacturing solutions required for broad market adoption. The project objectives were accomplished by: identifying viable technical solutions based on modeling of modern and potential coating stacks and IGU designs; development of new coating material sets for HM thin film stacks, as well as improved HM IGU designs to accept multiple layers of HM films; matching promising new coating designs with new HM IGU designs to demonstrate performance gains; and, in cooperation with a window manufacturer, assess the potential for high-volume manufacturing and cost efficiency of a HM-based R-10 window with improved solar heat gain characteristics. A broad view of available materials and design options was applied to achieve the desired improvements. Gated engineering methodologies were employed to guide the development process from concept generation to a window demonstration. The project determined that a slightly de-rated window performance allows formulation of a path to achieve the desired cost reductions to support end consumer adoption.

  12. Document: L1334 | Category: Physical Science, Materials License Status: Available for licensing || Texas Industry Cluster: Biotechnology and Life Sciences

    E-Print Network [OSTI]

    Lightsey, Glenn

    for licensing || Texas Industry Cluster: Biotechnology and Life Sciences Nanocomposite membranes for energy. These markets include hydrogen production, medical devices, advanced materials, and drug delivery. Development Engineering, The University of Texas at Austin OTC Contact Brian Cummings, Associate Director, Life Sciences

  13. Technical Assistance Contractor management plan. Revision 1

    SciTech Connect (OSTI)

    NONE

    1995-08-01T23:59:59.000Z

    The Technical Assistance Contractor (TAC) for the Uranium Mill Tailings Remedial Action (UMTRA) Project comprises Jacobs Engineering Group Inc. (JEG) as the prime contractor and three teaming partner subcontractors: Roy F. Weston, Inc. (RFW), AGRA Earth and Environmental, Inc. (AGRA), and Geraghty and Miller, Inc. (G and M). The TAC contract`s scope is to provide technical, analytical, environmental, engineering, design, inspection, and management support services to the US Department of Energy (DOE) for both Surface and Ground Water Projects. The TAC team supports the DOE in completing surface remedial action and initiating ground water remediation work for start-up, characterization, compliance planning, design, construction oversight, and remedial operations. The TAC provides the DOE UMTRA Project Team with a dedicated management, scientific, and technical resource base in Albuquerque, New Mexico, which is supplemented by corporate resources. A carefully developed and maintained staff of technical experts is available to assess, analyze, develop, and execute cost-effective solutions to the demanding technical and institutional problems presented by the UMTRA Project.

  14. Regulators Experiences in Licensing and Inspection of Dry Cask Storage Facilities

    SciTech Connect (OSTI)

    Baggett, S.; Brach, E.W. [Spent Fuel Project Office, U.S. Nuclear Regulatory Commission, Washington, DC 20555 (United States)

    2006-07-01T23:59:59.000Z

    The United States Nuclear Regulatory Commission (NRC), through the combination of a rigorous licensing and inspection program, ensures the safety and security of dry cask storage. NRC authorizes the storage of spent fuel at an independent spent fuel storage installation (ISFSI) under two licensing options: site-specific licensing and general licensing. In July 1986, the NRC issued the first site-specific license to the Surry Nuclear Power Plant in Virginia authorizing the interim storage of spent fuel in a dry storage cask configuration. Today, there are over 30 ISFSIs currently licensed by the NRC with over 700 loaded dry casks. Current projections identify over 50 ISFSIs by the year 2010. No releases of spent fuel dry storage cask contents or other significant safety problems from the storage systems in use today have been reported. This paper discusses the NRC licensing and inspection experiences. (authors)

  15. Technical Talks Timing

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    a technical talk is to communicate information to the audience. The Speaker Keep in mind that your objective is communication of information. Mumbling, monotone speech and use...

  16. DOE Technical Assistance Program

    Broader source: Energy.gov (indexed) [DOE]

    Designing Effective Residential Retrofit Programs eere.energy.gov The Parker Ranch installation in Hawaii DOE Technical Assistance Program Quality Assurance for Residential...

  17. Investing in the Energy Future: An Industry Guide to Licensing Technologies at the National Renewable Energy Laboratory (NREL) (Brochure)

    SciTech Connect (OSTI)

    Not Available

    2010-09-01T23:59:59.000Z

    Provides an overview of NREL's licensing opportunities and processes, and commercialization programs.

  18. NRC safety research in support of regulation. Volume 8, FY 1993

    SciTech Connect (OSTI)

    Not Available

    1994-06-01T23:59:59.000Z

    This report, the ninth in a series of annual reports, was prepared in response to congressional inquiries concerning how nuclear regulatory research is used. It summarizes the accomplishments of the Office of Nuclear Regulatory Research during FY 1993. A special emphasis on accomplishments in nuclear power plant aging research reflects recognition that number of plants are entering the final portion of their original 40-year operating licenses and that, in addition to current aging effects, a focus on safety considerations for license renewal becomes timely. The primary purpose of performing regulatory research is to develop and provide the Commission and its staff with sound technical bases for regulatory decisions on the safe operation of licensed nuclear reactors and facilities, to find unknown or unexpected safety problems, and to develop data and related information for the purpose of revising the Commission`s rules, regulatory guides, or other guidance.

  19. Sustainable energy for all. Technical report of task force 2 in support of doubling the global rate of energy efficiency improvement and doubling the share of renewable energy in the global energy mix by 2030

    SciTech Connect (OSTI)

    Nakicenovic, Nebojsa [International Institute for Applied Systems Analysis and Vienna University of Technology (Austria); Kammen, Daniel [Univ. of California, Berkeley, CA (United States); Jewell, Jessica [International Institute for Applied Systems Analysis (Austria)

    2012-04-15T23:59:59.000Z

    The UN Secretary General established the Sustainable Energy for All initiative in order to guide and support efforts to achieve universal access to modern energy, rapidly increase energy efficiency, and expand the use of renewable energies. Task forces were formed involving prominent energy leaders and experts from business, government, academia and civil society worldwide. The goal of the Task Forces is to inform the implementation of the initiative by identifying challenges and opportunities for achieving its objectives. This report contains the findings of Task Force Two which is dedicated energy efficiency and renewable energy objectives. The report shows that doubling the rate of energy efficiency improvements and doubling the share of energy from renewable sources by 2030 is challenging but feasible if sufficient actions are implemented. Strong and well-informed government policies as well as extensive private investment should focus on the high impact areas identified by the task force.

  20. Status of development and licensing support for advanced liquid metal reactors in the United States

    SciTech Connect (OSTI)

    Pedersen, D.R. (Argonne National Lab., IL (United States)); Gyorey, G. (General Electric Co., San Jose, CA (United States))

    1991-01-01T23:59:59.000Z

    The cornerstones of the United States Advanced Liquid Metal Cooled Reactor (ALMR) program sponsored by the Department of Energy are: the ALMR plant design program at General Electric based on the PRISM (Power Reactor Innovative Small Module) concept, and the Integral Fast Reactor program (IFR) at Argonne National Laboratory (ANL). The goal of the US program is to produce a standard, commercial ALMR, including the associated fuel cycle. The paper addresses the status of the IFR program, the ALMR program and the interaction of the ALMR program with the regulatory environment.

  1. Status of development and licensing support for advanced liquid metal reactors in the United States

    SciTech Connect (OSTI)

    Pedersen, D.R. [Argonne National Lab., IL (United States); Gyorey, G. [General Electric Co., San Jose, CA (United States)

    1991-12-01T23:59:59.000Z

    The cornerstones of the United States Advanced Liquid Metal Cooled Reactor (ALMR) program sponsored by the Department of Energy are: the ALMR plant design program at General Electric based on the PRISM (Power Reactor Innovative Small Module) concept, and the Integral Fast Reactor program (IFR) at Argonne National Laboratory (ANL). The goal of the US program is to produce a standard, commercial ALMR, including the associated fuel cycle. The paper addresses the status of the IFR program, the ALMR program and the interaction of the ALMR program with the regulatory environment.

  2. New York: EERE-Supported Catalyst Licensed for Use in Fuel Cell Hybrid

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE: Alternative JC3 RSS September 9, 2013 V-237:MultimediaConsumers'Department ofof EnergyAdvanced

  3. Race to license new MTBE and TAME routes heats up

    SciTech Connect (OSTI)

    Rotman, D.

    1993-01-06T23:59:59.000Z

    With refineries and petrochemical manufacturers continuing to gear up production of oxygenates for use in reformulated fuels, new routes to methyl tert-butyl ether (MTBE) and tert-amyl methyl ether (TAME) are clearly hot items in the licensing market. And probably nowhere has the competition become as intense as in offerings for skeletal isomerization technologies to boost ethers production from fluid catalytic cracking and steam cracking.

  4. Federal Technical Capability

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2009-11-19T23:59:59.000Z

    To define requirements and responsibilities for meeting the Department of Energy (DOE) commitment to recruiting, deploying, developing, and retaining a technically competent workforce that will accomplish DOE missions in a safe and efficient manner through the Federal Technical Capability Program (FTCP). Chg. 1 dated 9-20-11 Cancels DOE O 426.1. Cancels DOE P 426.1.

  5. About Technical Assistance

    Broader source: Energy.gov [DOE]

    As technologies proceed along the development pipeline, most face major hurdles as they attempt to enter commercial markets. Our Technical Assistance program helps lower a range of institutional barriers to prepare innovative, energy-efficient technologies and energy management systems for full commercial deployment. These projects and activities address barriers that are not technical, Technology Readiness Level 9.

  6. Technical Report Computer Laboratory

    E-Print Network [OSTI]

    Haddadi, Hamed

    the opportunity to consider a physical attack, with very little to lose. We thus set out to analyse the deviceTechnical Report Number 592 Computer Laboratory UCAM-CL-TR-592 ISSN 1476-2986 Unwrapping J. Murdoch Technical reports published by the University of Cambridge Computer Laboratory are freely

  7. Federal Technical Capability Manual

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2000-06-05T23:59:59.000Z

    The Federal Technical Capability Manual provides the process for the recruitment, deployment, development, and retention of Federal personnel with the demonstrated technical capability to safely accomplish the Departments missions and responsibilities at defense nuclear facilities. Canceled by DOE M 426.1-1A. Does not cancel other directives.

  8. Depleted Uranium Technical Brief

    E-Print Network [OSTI]

    Depleted Uranium Technical Brief United States Environmental Protection Agency Office of Air and Radiation Washington, DC 20460 EPA-402-R-06-011 December 2006 #12;#12;Depleted Uranium Technical Brief EPA of Radiation and Indoor Air Radiation Protection Division ii #12;iii #12;FOREWARD The Depleted Uranium

  9. MATHEMATICAL ENGINEERING TECHNICAL REPORTS

    E-Print Network [OSTI]

    Yamamoto, Hirosuke

    MATHEMATICAL ENGINEERING TECHNICAL REPORTS A Subband Coding Approach to Control under Limited Data Rates and Message Losses Hideaki ISHII and Shinji HARA (Communicated by Kazuo Murota) METR 2006­22 April METR technical reports are published as a means to ensure timely dissemination of scholarly

  10. Improved best estimate plus uncertainty methodology including advanced validation concepts to license evolving nuclear reactors

    SciTech Connect (OSTI)

    Unal, Cetin [Los Alamos National Laboratory; Williams, Brian [Los Alamos National Laboratory; Mc Clure, Patrick [Los Alamos National Laboratory; Nelson, Ralph A [IDAHO NATIONAL LAB

    2010-01-01T23:59:59.000Z

    Many evolving nuclear energy programs plan to use advanced predictive multi-scale multi-physics simulation and modeling capabilities to reduce cost and time from design through licensing. Historically, the role of experiments was primary tool for design and understanding of nuclear system behavior while modeling and simulation played the subordinate role of supporting experiments. In the new era of multi-scale multi-physics computational based technology development, the experiments will still be needed but they will be performed at different scales to calibrate and validate models leading predictive simulations. Cost saving goals of programs will require us to minimize the required number of validation experiments. Utilization of more multi-scale multi-physics models introduces complexities in the validation of predictive tools. Traditional methodologies will have to be modified to address these arising issues. This paper lays out the basic aspects of a methodology that can be potentially used to address these new challenges in design and licensing of evolving nuclear technology programs. The main components of the proposed methodology are verification, validation, calibration, and uncertainty quantification. An enhanced calibration concept is introduced and is accomplished through data assimilation. The goal is to enable best-estimate prediction of system behaviors in both normal and safety related environments. To achieve this goal requires the additional steps of estimating the domain of validation and quantification of uncertainties that allow for extension of results to areas of the validation domain that are not directly tested with experiments, which might include extension of the modeling and simulation (M&S) capabilities for application to full-scale systems. The new methodology suggests a formalism to quantify an adequate level of validation (predictive maturity) with respect to required selective data so that required testing can be minimized for cost saving purposes by showing further testing wold not enhance the quality of the validation of predictive tools. The proposed methodology is at a conceptual level. When matured and if considered favorably by the stakeholders, it could serve as a new framework for the next generation of the best estimate plus uncertainty licensing methodology that USNRC developed previously. In order to come to that level of maturity it is necessary to communicate the methodology to scientific, design and regulatory stakeholders for discussion and debates. This paper is the first step to establish this communication.

  11. TECHNICAL BASIS DOCUMENT FOR NATURAL EVENT HAZARDS

    SciTech Connect (OSTI)

    KRIPPS, L.J.

    2006-07-31T23:59:59.000Z

    This technical basis document was developed to support the documented safety analysis (DSA) and describes the risk binning process and the technical basis for assigning risk bins for natural event hazard (NEH)-initiated accidents. The purpose of the risk binning process is to determine the need for safety-significant structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls for a given representative accident or represented hazardous conditions based on an evaluation of the frequency and consequence. Note that the risk binning process is not applied to facility workers, because all facility worker hazardous conditions are considered for safety-significant SSCs and/or TSR-level controls.

  12. Technical basis document for natural event hazards

    SciTech Connect (OSTI)

    CARSON, D.M.

    2003-03-20T23:59:59.000Z

    This technical basis document was developed to support the Tank Farms Documented Safety Analysis (DSA), and describes the risk binning process and the technical basis for assigning risk bins for natural event hazards (NEH)-initiated representative accident and associated represented hazardous conditions. The purpose of the risk binning process is to determine the need for safety-significant structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls for a given representative accident or represented hazardous conditions based on an evaluation of the frequency and consequence. Note that the risk binning process is not applied to facility workers, because all facility worker hazardous conditions are considered for safety-significant SSCs and/or TSR-level controls. Determination of the need for safety-class SSCs was performed in accordance with DOE-STD-3009-94, ''Preparation Guide for US Department of Energy Nonreactor Nuclear Facility Documented Safety Analyses'', as described in this report.

  13. Geotechnical support and topical studies for nuclear waste geologic repositories

    SciTech Connect (OSTI)

    Not Available

    1989-01-01T23:59:59.000Z

    The present report lists the technical reviews and comments made during the fiscal year 1988 and summarizes the technical progress of the topical studies. In the area of technical assistance, there were numerous activities detailed in the next section. These included 24 geotechnical support activities, including reviews of 6 Study Plans (SP) and participation in 6 SP Review Workshops, review of one whole document Site Characterization Plan (SCP) and participation in the Assembled Document SCP Review Workshops by 6 LBL reviewers; the hosting of a DOE program review, the rewriting of the project statement of work, 2 trips to technical and planning meetings; preparation of proposed work statements for two new topics for DOE, and 5 instances of technical assistance to DOE. These activities are described in a Table in the following section entitled Geoscience Technical Support for Nuclear Waste Geologic Repositories.''

  14. Kentucky Water Resources Research Institute Annual Technical Report

    E-Print Network [OSTI]

    contaminants at the Maxey Flats Nuclear Disposal Site and the Paducah Gaseous Diffusion Plant). The Kentucky Diffusion Plant. Over 20 technical projects supported through the consortium presented results during 2007 with efforts supporting a variety of environmental assessment and cleanup activities at the Paducah Gasous

  15. NASA Technical Memorandum 108846 Interviews with the Apollo

    E-Print Network [OSTI]

    Rathbun, Julie A.

    NASA Technical Memorandum 108846 Interviews with the Apollo Lunar Surface Astronauts in Support-1000 #12;Interviews with the Apollo Lunar Surface Astronauts in Support of Planning for EVA Systems Design interviews were conducted with the Apollo astronauts who landed on the Moon. The purpose of these interviews

  16. Active Technical Standards Managers List

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    TECHNICAL STANDARDS PROGRAM ASSIGNMENT TELEPHONEFAXEMAIL NAME DOE FACILITYADDRESS LOC CODE AU-30 Jeff D. Feit DOE Technical Standards Program, Manager U.S. Department of Energy...

  17. EPA Tribal Training and Outreach Support for the American Indian Air Quality Training Program

    Broader source: Energy.gov [DOE]

    The U.S. Environmental Protection Agency (EPA) is accepting applications to provide training, and technical and outreach support for the American Indian Air Quality Training Program.

  18. "Furthering Your Local Governments' Energy Efficiency Goals-- Part 1- Getting Support From Local Leaders "

    Broader source: Energy.gov [DOE]

    DOE’s technical assistance program webcast on furthering your local government’s energy efficiency goals. This is part one, gaining support from local leaders.

  19. Collaboration and Consensus Building in States to Support Energy Efficiency as a Resource

    Broader source: Energy.gov [DOE]

    This presentation, given through the DOE's Technical Assitance Program (TAP), provides information on collaboration and consensus building in states to support energy efficiency as a resource.

  20. Southwest Region Experiment Station - Final Technical Report

    SciTech Connect (OSTI)

    Rosenthal, A

    2011-08-19T23:59:59.000Z

    Southwest Technology Development Institute (SWTDI), an independent, university-based research institute, has been the operator of the Southwest Region Photovoltaic Experiment Station (SWRES) for almost 30 years. The overarching mission of SWTDI is to position PV systems and solar technologies to become cost-effective, major sources of energy for the United States. Embedded in SWTDI's general mission has been the more-focused mission of the SWRES: to provide value added technical support to the DOE Solar Energy Technologies Program (SETP) to effectively and efficiently meet the R&D needs and targets specified in the SETP Multi-Year Technical Plan. : The DOE/SETP goals of growing U.S. PV manufacturing into giga-watt capacities and seeing tera-watt-hours of solar energy production in the U.S. require an infrastructure that is under development. The staff of the SWRES has supported DOE/SETP through a coherent, integrated program to address infrastructural needs inhibiting wide-scale PV deployment in three major technical categories: specialized engineering services, workforce development, and deployment facilitation. The SWRES contract underwent three major revisions during its five year period-of- performance, but all tasks and deliverables fell within the following task areas: Task 1: PV Systems Assistance Center 1. Develop a Comprehensive multi-year plan 2. Provide technical workforce development materials and workshops for PV stakeholder groups including university, professional installers, inspectors, state energy offices, Federal agencies 3. Serve on the NABCEP exam committee 4. Provide on-demand technical PV system design reviews for U.S. PV stakeholders 5. Provide PV system field testing and instrumentation, technical outreach (including extensive support for the DOE Market Transformation program) Task 2: Design-for-Manufacture PV Systems 1. Develop and install 18 kW parking carport (cost share) and PV-thermal carport (Albuquerque) deriving and publishing lessons learned Task 3: PV Codes and Standards 1. Serve as the national lead for development and preparation of all proposals (related to PV) to the National Electrical Code 2. Participate in the Standards Technical Panels for modules (UL1703) and inverters (UL1741) Task 4: Assess Inverter Long Term Reliability 1. Install and monitor identical inverters at SWRES and SERES 2. Operate and monitor all inverters for 5 years, characterizing all failures and performance trends Task 5: Test and Evaluation Support for Solar America Initiative 1. Provide test and evaluation services to the National Laboratories for stage gate and progress measurements of SAI TPP winners

  1. Repression of DNA replication licensing in quiescence is independent of geminin and may define the cell cycle state of progenitor cells

    SciTech Connect (OSTI)

    Kingsbury, Sarah R. [Wolfson Institute for Biomedical Research, University College London, Cruciform Building, Gower Street, London WC1E 6BT (United Kingdom); Loddo, Marco [Department of Pathology, University College London, Rockefeller Building, University Street, London WC1E 6JJ (United Kingdom); Fanshawe, Thomas [Centre for Applied Medical Statistics and General Practice and Primary Care Research Unit, Department of Public Health and Primary Care, University of Cambridge, Forvie Site, Robinson Way, Cambridge CB2 2SR (United Kingdom); Obermann, Ellen C. [Department of Pathology, University College London, Rockefeller Building, University Street, London WC1E 6JJ (United Kingdom); Prevost, A. Toby [Medical Research Council Biostatistics Unit, Institute of Public Health, Forvie Site, Robinson Way, Cambridge CB2 2SR (United Kingdom); Stoeber, Kai [Wolfson Institute for Biomedical Research, University College London, Cruciform Building, Gower Street, London WC1E 6BT (United Kingdom) and Department of Pathology, University College London, Rockefeller Building, University Street, London WC1E 6JJ (United Kingdom)]. E-mail: k.stoeber@ucl.ac.uk; Williams, Gareth H. [Wolfson Institute for Biomedical Research, University College London, Cruciform Building, Gower Street, London WC1E 6BT (United Kingdom); Department of Pathology, University College London, Rockefeller Building, University Street, London WC1E 6JJ (United Kingdom)

    2005-09-10T23:59:59.000Z

    The DNA replication (or origin) licensing machinery ensures precise duplication of the genome and contributes to the regulation of proliferative capacity in metazoa. Using an in vitro fibroblast model system coupled to a cell-free DNA replication assay, we have studied regulation of the origin licensing pathway during exit from and re-entry into the mitotic cell cycle. We show that in the quiescent state (G0) loss of proliferative capacity is achieved in part through down-regulation of the replication licensing factors Cdc6 and Mcm2-7. The origin licensing repressor geminin is absent in quiescent fibroblasts, suggesting that this powerful inhibitor of the licensing machinery is not required to suppress proliferative capacity in G0. Geminin expression is induced at a late stage in the G0-S transition post pre-RC assembly. Ectopic geminin can block re-acquisition of DNA replication competence during re-entry into the cell cycle, indicating that geminin levels must be tightly down-regulated for escape from G0. Analysis of geminin levels in thyroid shows that geminin expression is suppressed in anatomical compartments/tissues harbouring quiescent cells, confirming our in vitro data. Spatio-temporal control of geminin expression may therefore be of particular relevance for multi-potential stem cells which cycle infrequently. In support of this hypothesis, we have identified a unique population of cells in the putative stem cell niche of intestinal epithelium that are unlicensed and lack geminin expression, a prerequisite for successful re-entry into cycle. Our data argue that the prolonged cell cycle times observed for intestinal stem cells could be due to exit of progenitor cells from cycle into an unlicensed 'out-of-cycle' state, a powerful mechanism by which rapidly proliferating tissues may resist genotoxic insult.

  2. Technical Foundations of the Agent Contest 2008

    E-Print Network [OSTI]

    Zachmann, Gabriel

    (Technical Computer Science) Prof. Dr. Gabriel Zachmann (Computer Graphics) #12;Technical Foundations

  3. Technical Standards, Style Guide- August 1, 2000

    Broader source: Energy.gov [DOE]

    Style Guide for the Preparation of DOE Technical Standards (Standards, Handbooks, and Technical Standards Lists)

  4. Final Scientific/Technical Report, USDOE Award DE-FG-02ER54684, Recipient: CompX, Project Title: Fokker-Planck/Ray Tracing for Electron Bernstein and Fast Wave Modeling in Support of NSTX.

    SciTech Connect (OSTI)

    R.W. Harvey, CompX, Del Mar, CA 92014

    2009-11-12T23:59:59.000Z

    This DOE grant supported fusion energy research, a potential long-term solution to the world's energy needs. Magnetic fusion, exemplified by confinement of very hot ionized gases, i.e., plasmas, in donut-shaped tokamak vessels is a leading approach for this energy source. Thus far, a mixture of hydrogen isotopes has produced 10's of megawatts of fusion power for seconds in a tokamak reactor at Princeton Plasma Physics Laboratory in New Jersey. The research grant under consideration, ER54684, uses computer models to aid in understanding and projecting efficacy of heating and current drive sources in the National Spherical Torus Experiment, a tokamak variant, at PPPL. The NSTX experiment explores the physics of very tight aspect ratio, almost spherical tokamaks, aiming at producing steady-state fusion plasmas. The current drive is an integral part of the steady-state concept, maintaining the magnetic geometry in the steady-state tokamak. CompX further developed and applied models for radiofrequency (rf) heating and current drive for applications to NSTX. These models build on a 30 year development of rf ray tracing (the all-frequencies GENRAY code) and higher dimensional Fokker-Planck rf-collisional modeling (the 3D collisional-quasilinear CQL3D code) at CompX. Two mainline current-drive rf modes are proposed for injection into NSTX: (1) electron Bernstein wave (EBW), and (2) high harmonic fast wave (HHFW) modes. Both these current drive systems provide a means for the rf to access the especially high density plasma--termed high beta plasma--compared to the strength of the required magnetic fields. The CompX studies entailed detailed modeling of the EBW to calculate the efficiency of the current drive system, and to determine its range of flexibility for driving current at spatial locations in the plasma cross-section. The ray tracing showed penetration into NSTX bulk plasma, relatively efficient current drive, but a limited ability to produce current over the whole radial plasma cross-section. The actual EBW experiment will cost several million dollars, and remains in the proposal stage. The HHFW current drive system has been experimentally implemented on NSTX, and successfully drives substantial current. The understanding of the experiment is to be accomplished in terms of general concepts of rf current drive, and also detailed modeling of the experiment which can discern the various competing processes which necessarily occur simultaneously in the experiment. An early discovery of the CompX codes, GENRAY and CQL3D, was that there could be significant interference between the neutral beam injection fast ions in the machine (injected for plasma heating) and the HHFW energy. Under many NSTX experimental conditions, power which could go to the fast ions would then be unavailable for current drive by the desired HHFW interaction with electrons. This result has been born out by experiments; the modeling helps in understanding difficulties with HHFW current drive, and has enabled adjustment of the experiment to avoid interaction with neutral beam injected fast ions thereby achieving stronger HHFW current drive. The detailed physics modeling of the various competing processes is almost always required in fusion energy plasma physics, to ensure a reasonably accurate and certain interpretation of the experiment, enabling the confident design of future, more advanced experiments and ultimately a commercial fusion reactor. More recent work entails detailed investigation of the interaction of the HHFW radiation for fast ions, accounting for the particularly large radius orbits in NSTX, and correlations between multiple HHFW-ion interactions. The spherical aspect of the NSTX experiment emphasized particular physics such as the large orbits which are present to some degree in all tokamaks, but gives clearer clues on the resulting physics phenomena since competing physics effects are reduced.

  5. Atomic Safety and Licensing Board Panel annual report, Fiscal year 1992

    SciTech Connect (OSTI)

    Not Available

    1993-09-01T23:59:59.000Z

    In Fiscal Year 1992, the Atomic Safety and Licensing Board Panel (``the Panel``) handled 38 proceedings. The cases addressed issues in the construction, operation, and maintenance of commercial nuclear power reactors and other activities requiring a license from the Nuclear Regulatory Commission. This reports sets out the Panel`s caseload during the year and summarizes, highlights, and analyzes how the wide-ranging issues raised in those proceedings were addressed by the Panel`s judges and licensing boards.

  6. 1993 DOE technical standards managers workshop: Proceedings

    SciTech Connect (OSTI)

    Not Available

    1993-12-31T23:59:59.000Z

    This workshop is focused on the benefits of the DOE technical standards program, which is focused toward the preferred use of non-Government standards for DOE activities and the development of DOE technical standards when non-Government standards are not available or are inappropriate. One goal of the program is to replace redundant site-specific standards with more universally accepted documents that have been scrutinized by experts. This replacement is discussed at the workshop along with the problems encountered and solutions found. The workshop provided an opportunity for geographically dispersed people to meet and advance their standards knowledge and efforts to support the program. Safety issues have been the driving force behind the program to date. Several companies offer products and services that support the development, processing, and retrieval of standards. This document mostly comprise vugraphs.

  7. Profit Neutrality in Licensing: The Boundary Between Antitrust Law and Patent Law

    E-Print Network [OSTI]

    Maurer, Stephen M.; Scotchmer, Suzanne

    2004-01-01T23:59:59.000Z

    Strategy 1-32. [22] Royal Industries v. St. Regis Paperal. , 2004, at 31:20; Royal Industries 1969), to licenses

  8. ASTM standards associated with PWR and BWR power plant licensing, operation and surveillance

    SciTech Connect (OSTI)

    McElroy, W.N. [Consultants and Technology Services, Richland, WA (United States); McElroy, R.J. [AEA Reactor Services, Harwell (United Kingdom); Gold, R. [Metrology Control Corp., Richland, WA (United States); Lippincott, E.P. [Westinghouse Electric Corp., Pittsburgh, PA (United States); Lowe, A.L. Jr. [BW Nuclear Technologies, Lynchburg, VA (United States)

    1994-12-31T23:59:59.000Z

    This paper considers ASTM Standards that are available, under revision, and are being considered in support of Pressurized Water Reactor (PWR) and Boiling Water Reactor (BWR) Nuclear Power Plant (NPP) licensing, regulation, operation, surveillance and life attainment. The current activities of ASTM Committee E10 and its Subcommittees E10.02 and current activities of ASTM Committee E10 and its Subcommittees E10.02 and E10.05 and their Task Groups (TG) are described. A very important aspect of these efforts is the preparation, revision, and balloting of standards identified in the ASTM E706 Standard on Master Matrix for Light Water Reactor (LWR) Pressure Vessel (PV) Surveillance Standards. The current version (E706-87) of the Master Matrix identifies 21 ASTM LWR physics-dosimetry-metallurgy standards for Reactor Pressure Vessel (RPV) and Support Structure (SS) surveillance programs, whereas, for the next revision 34 standards are identified. The need for national and international coordination of Standards Technology Development, Transfer and Training (STDTT) is considered in this and other Symposium papers that address specific standards related physics-dosimetry-metallurgy issues. 69 refs.

  9. Technical Planning Basis

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2007-07-11T23:59:59.000Z

    The Guide assists DOE/NNSA field elements and operating contractors in identifying and analyzing hazards at facilities and sites to provide the technical planning basis for emergency management programs. Cancels DOE G 151.1-1, Volume 2.

  10. Technical Standards Program

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2011-02-23T23:59:59.000Z

    The order establishes the DOE Technical Standards Program. Cancels DOE O 252.1 and DOE G 252.1-1. Admin Chg 1, dated 3-12-13 cancels DOE O 252.1A.

  11. DOE Technical Assistance Program

    Broader source: Energy.gov (indexed) [DOE]

    Solid-State Solutions for Municipal Lighting: What You'll Need to Know eere.energy.gov The Parker Ranch installation in Hawaii DOE Technical Assistance Program Solid-State...

  12. Lightweight Support for FineGrained Persistence on Stock Hardware

    E-Print Network [OSTI]

    Massachusetts at Amherst, University of

    cannot survive the Ph.D. experience without the support and guidance of a great many people. To those and improving the garbage collector toolkit, Rick Hudson for our many technical discussions, and Norm Walsh

  13. Lightweight Support for Fine-Grained Persistence on Stock Hardware

    E-Print Network [OSTI]

    Hosking, Antony

    cannot survive the Ph.D. experience without the support and guidance of a great many people. To those the garbage collector toolkit, Rick Hudson for our many technical discussions, and Norm Walsh for his advice

  14. Procurement of a fully licensed radioisotope thermoelectric generator transportation system

    SciTech Connect (OSTI)

    Adkins, H.E.; Bearden, T.E. (Westinghouse Hanford Company, P.O. Box 1970, N1-42, Richland, Washington 99352 (US))

    1991-01-01T23:59:59.000Z

    A fully licensed transportation system for Radioisotope Thermoelectric Generators and Light-Weight Radioisotope Heater Units is currently being designed and built. The system will comply with all applicable U.S. Department of Transportation regulations without the use of a DOE Alternative.'' The U.S. Department of Transportation has special double containment'' requirements for plutonium. The system packaging uses a doubly contained bell jar'' concept. A refrigerated trailer is used for cooling the high-heat payloads. The same packaging is used for both high- and low-heat payloads. The system is scheduled to be available for use by mid-1992.

  15. Procurement of a fully licensed radioisotope thermoelectric generator transportation system

    SciTech Connect (OSTI)

    Adkins, H.E.; Bearden, T.E.

    1990-10-01T23:59:59.000Z

    A fully licensed transportation system for Radioisotope Thermoelectric Generators and Light-Weight Radioisotope Heater Units is currently being designed and built. The system will comply with all applicable US Department of Transportation regulations without the use of a DOE Alternative.'' The US Department of Transportation has special double containment'' requirements for plutonium. The system packaging uses a doubly contained bell jar'' concept. A refrigerated trailer is used for cooling the high-heat payloads. The same packaging is used for both high- and low-heat payloads. The system is scheduled to be available for use by mid-1992. 4 refs., 4 figs., 2 tabs.

  16. Sandia Energy - NuMAD License and Disclaimer

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of ScienceandMesa del Sol Home Distribution Grid Integration PermalinkClimate ChangeLicense and

  17. Property:Permit/License Buildout (MW) | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere I Geothermal PwerPerkinsInformationInformationMarine/Riverline Conditions Jump to:Permit/License

  18. The Future of Technical Assistance, Funding and Finding Alternatives

    E-Print Network [OSTI]

    Oliver, R.

    2011-01-01T23:59:59.000Z

    ? Tools ? Local and individual technical support ? Budget analysis for operations and maintenance ? Cost analysis and management ? Financial alternatives ? Grant writing ? Construction and retrofit alternatives ? Back office Putting an energy...The Future of Technical Assistance, Funding and Financing Alternatives Rich Oliver, McKinstry More ?no cost or at risk? assistance in Texas than ever before ? Mentoring by Private Sector ? Education and outreach services ? Documents...

  19. TECHNICAL BASIS FOR VENTILATION REQUIREMENTS IN TANK FARMS OPERATING SPECIFICATIONS DOCUMENTS

    SciTech Connect (OSTI)

    BERGLIN, E J

    2003-06-23T23:59:59.000Z

    This report provides the technical basis for high efficiency particulate air filter (HEPA) for Hanford tank farm ventilation systems (sometimes known as heating, ventilation and air conditioning [HVAC]) to support limits defined in Process Engineering Operating Specification Documents (OSDs). This technical basis included a review of older technical basis and provides clarifications, as necessary, to technical basis limit revisions or justification. This document provides an updated technical basis for tank farm ventilation systems related to Operation Specification Documents (OSDs) for double-shell tanks (DSTs), single-shell tanks (SSTs), double-contained receiver tanks (DCRTs), catch tanks, and various other miscellaneous facilities.

  20. Final technical evaluation report for the proposed revised reclamation plan for the Atlas Corporation Moab Mill

    SciTech Connect (OSTI)

    NONE

    1997-03-01T23:59:59.000Z

    This final Technical Evaluation Report (TER) summarizes the US Nuclear Regulatory Commission staff`s review of Atlas Corporation`s proposed reclamation plan for its uranium mill tailings pile near Moab, Utah. The proposed reclamation would allow Atlas to (1) reclaim the tailings pile for permanent disposal and long-term custodial care by a government agency in its current location on the Moab site, (2) prepare the site for closure, and (3) relinquish responsibility of the site after having its NRC license terminated. The NRC staff concludes that, subject to license conditions identified in the TER, the proposed reclamation plan meets the requirements identified in NRC regulations, which appear primarily in 10 CFR Part 40. 112 refs., 6 figs., 16 tabs.

  1. International Support On Hosting or Hiring Internationals Since 9/11

    E-Print Network [OSTI]

    Almor, Amit

    -Mail: isfs@sc.edu Website: http://hr.sc.edu/international.html #12;Hosting or Hiring Internationals | Page 2. Instructions are on the ISFS website; Best practice is to submit form both to Immigration & to International Support. State law sets special requirements for issuance of a S.C. driver's license E-Verify/FAR rules

  2. University of Rochester Model Non-Exclusive Patent License revised 11-08-2013

    E-Print Network [OSTI]

    University of Rochester Model Non-Exclusive Patent License revised 11-08-2013 DRAFT DATED__________ FOR DISCUSSION PURPOSES ONLY NON EXCLUSIVE PATENT LICENSE AGREEMENT This agreement (hereinafter "Agreement, University is the owner by assignment of the Patent Rights as defined below. 1.2 University desires

  3. Profit Neutrality in Licensing: The Boundary Between Antitrust Law and Patent Law

    E-Print Network [OSTI]

    Sadoulet, Elisabeth

    Profit Neutrality in Licensing: The Boundary Between Antitrust Law and Patent Law Stephen M. Maurer a century, courts and commentators have struggled to find principles that reconcile patent and antitrust law, especially as to patent licensing. We interpret case law and commentary to arrive at three unifying

  4. Supporting steel

    SciTech Connect (OSTI)

    Badra, C. [International Trade Commission, Washington, DC (United States)

    1995-10-01T23:59:59.000Z

    The US Department of Energy (DOE) and the American Iron and Steel Institute (AISI) have just completed a pilot program on the technical and economic viability of direct ironmaking by a process based on bath smelting. In this process, oxygen, prereduced iron ore pellets, coal, and flux are charged into a molten slag bath containing a high percentage of carbon. The carbon removes oxygen from the iron ore and generates carbon monoxide and liquid iron. Oxygen is then injected to burn some of the carbon monoxide gas before it leaves the smelting vessel. The partially combusted gas is sued to preheat and prereduced the ore before it is injected into the bath. There are several competing cokeless ironmaking processes in various stages of development around the world. A brief comparison of these processes provides a useful perspective with which to gauge the progress and objectives of the AISI-DOE research initiative. The principal competing foreign technologies include the Corex process, DIOS, HIsmelt, and Jupiter. The advantages of the direct ironmaking process examined by AISI-DOE were not sufficiently demonstrated to justify commercialization without further research. However, enough knowledge was gained from laboratory and pilot testing to teach researchers how to optimize the direct ironmaking process and to provide the foundation for future research. Researchers now better understand issues such as the dissolution of materials, reduction mechanisms and rates, slag foaming and control, the behavior of sulfur, dust generation, and the entire question of energy efficiency--including post combustion and the role of coal/volatile matter.

  5. DOE Awards $15 Million in Technical Assistance to Support Major...

    Office of Environmental Management (EM)

    of Energy (DOE) today announced the first phase of awards, valued at 15 million, for the Net-Zero Energy Commercial Building Initiative (CBI). Twenty-one companies, which will...

  6. DOCKET NO: A-98-49 TECHNICAL SUPPORT DOCUMENT FOR

    E-Print Network [OSTI]

    ............................................................15 2.2.2 Oak Ridge National Laboratory CRA Data Assembly..............................16 2.2.3 Savannah River Site CRA Data Assembly................................................17 2.3 SNL/LANL Data

  7. DOE Seeks Expression of Interest for Carlsbad Technical Support Services |

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 111 1,613PortsmouthBartlesvilleAbout »Department of2Violating

  8. Notice of Technical Workshop in Support of 2009 Electric Transmission

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn'tOrigin of Contamination in ManyDepartment of Energy NorthB O N N E V I

  9. Technical, Engineering, and Programmatic Support (TEPS) Blanket Purchase

    National Nuclear Security Administration (NNSA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA groupTuba City,EnrichedSupplemental Directives | National Nuclear

  10. Research Call to DOE/Federal Laboratories: Technical Support for

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 1112011 Strategic2 OPAM615_CostNSAR -Department ofEMSpent NuclearEnergy

  11. ARPA-E Technical Support Memo Appendices | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742Energy China 2015ofDepartmentDepartment of2 of 5) ALARA TrainingANDREW ( ARI )GrandAPPENDICES

  12. ARPA-E Technical Support Memo | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742Energy China 2015ofDepartmentDepartment of2 of 5) ALARA TrainingANDREW ( ARI

  13. Task Order Awarded for Technical Support Services | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn April 23, 2014,ZaleskiThis Decision considersTable 1: PointsGasContact Lynette

  14. ALARA Training for Technical Support Personnel - Change Notice Approval Memo

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 1112011 Strategic2UraniumEnergyDepartment54th6-04v2.pdf4.pdf AL2010-04.pdf AL2010-04.pdf2

  15. Research Call to DOE/Federal Laboratories: Technical Support for

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn April 23, 2014, an OHASeptemberAssessments |FossilThis document providesDepartment

  16. Grocery Store 50% Energy Savings Technical Support Document 2009 | Open

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are8COaBulkTransmissionSitingProcess.pdfGetec AG ContractingGreenOrderNebraska:Gridley,Grocery 2009 TSD MiamiEnergy

  17. Department of Energy Technical Support Document National Environmental

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny:Revised Finding of No53197E T A * S H I E L D * A L A R AFY'07 |Policy Act

  18. Fayetteville Shale Decision Support and Information System FINAL TECHNICAL REPORT

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power AdministrationField8,Dist. Category UC-lFederalFYRANDOMFailure Modesflow

  19. NREL: Technology Deployment - Project Technical Assistance and Support

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What's Possible for Renewable Energy: Grid Integration NRELCostBuildingModels andProject Success

  20. General Merchandise 50% Energy Savings Technical Support Document 2009 |

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are8COaBulkTransmissionSitingProcess.pdf Jump1946865°,Park, Texas:Webinars/Puesta enOpenEnergy InformationOpen

  1. Net Zero Waste - Tools and Technical Support ...and other observations |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn'tOrigin of Contamination in Many DevilsForum |Energy NovemberC OEnergyDepartment

  2. Climate Vison: Resources and Links - Technical Information

    Office of Scientific and Technical Information (OSTI)

    Technical Information Publications Case Studies Publications DOE BestPractices Technical Publications The DOE BestPractices team offers a broad selection of technical publications...

  3. Technical Consultant RFP | Department of Energy

    Energy Savers [EERE]

    RFP Technical Consultant RFP Technical Consultant RFP, from the Tool Kit Framework: Small Town University Energy Program (STEP). C3b Technical Consultant RFP.pdf More Documents &...

  4. The Independent Technical Analysis Process Final Report 2006-2007.

    SciTech Connect (OSTI)

    Duberstein, Corey; Ham, Kenneth; Dauble, Dennis; Johnson, Gary [Pacific Northwest National Laboratory

    2007-03-01T23:59:59.000Z

    The Bonneville Power Administration (BPA) contracted with the Pacific Northwest National Laboratory (PNNL) to provide technical analytical support for system-wide fish passage information (BPA Project No. 2006-010-00). The goal of this project was to produce rigorous technical analysis products using independent analysts and anonymous peer reviewers. This project provided an independent technical source for non-routine fish passage analyses while allowing routine support functions to be performed by other well-qualified entities. The Independent Technical Analysis Process (ITAP) was created to provide non-routine analysis for fish and wildlife agencies and tribes in particular and the public in general on matters related to juvenile and adult salmon and steelhead passage through the mainstem hydrosystem. The process was designed to maintain the independence of analysts and reviewers from parties requesting analyses, to avoid potential bias in technical products. The objectives identified for this project were to administer a rigorous, transparent process to deliver unbiased technical assistance necessary to coordinate recommendations for storage reservoir and river operations that avoid potential conflicts between anadromous and resident fish. Seven work elements, designated by numbered categories in the Pisces project tracking system, were created to define and accomplish project goals as follows: (1) 118 Coordination - Coordinate technical analysis and review process: (a) Retain expertise for analyst/reviewer roles. (b) Draft research directives. (c) Send directive to the analyst. (d) Coordinate two independent reviews of the draft report. (e) Ensure reviewer comments are addressed within the final report. (2) 162 Analyze/Interpret Data - Implement the independent aspects of the project. (3) 122 Provide Technical Review - Implement the review process for the analysts. (4) 132 Produce Annual Report - FY06 annual progress report with Pisces Disseminate (5) 161 Disseminate Raw/Summary Data and Results - Post technical products on the ITAP web site. (6) 185-Produce Pisces Status Report - Provide periodic status reports to BPA. (7) 119 Manage and Administer Projects - project/contract administration.

  5. Sensor network based vehicle classification and license plate identification system

    SciTech Connect (OSTI)

    Frigo, Janette Rose [Los Alamos National Laboratory; Brennan, Sean M [Los Alamos National Laboratory; Rosten, Edward J [Los Alamos National Laboratory; Raby, Eric Y [Los Alamos National Laboratory; Kulathumani, Vinod K [WEST VIRGINIA UNIV.

    2009-01-01T23:59:59.000Z

    Typically, for energy efficiency and scalability purposes, sensor networks have been used in the context of environmental and traffic monitoring applications in which operations at the sensor level are not computationally intensive. But increasingly, sensor network applications require data and compute intensive sensors such video cameras and microphones. In this paper, we describe the design and implementation of two such systems: a vehicle classifier based on acoustic signals and a license plate identification system using a camera. The systems are implemented in an energy-efficient manner to the extent possible using commercially available hardware, the Mica motes and the Stargate platform. Our experience in designing these systems leads us to consider an alternate more flexible, modular, low-power mote architecture that uses a combination of FPGAs, specialized embedded processing units and sensor data acquisition systems.

  6. Technical Report Computer Laboratory

    E-Print Network [OSTI]

    Haddadi, Hamed

    for criminal activity. One general attack route to breach the security is to carry out physical attack afterTechnical Report Number 829 Computer Laboratory UCAM-CL-TR-829 ISSN 1476-2986 Microelectronic report is based on a dissertation submitted January 2009 by the author for the degree of Doctor

  7. MATHEMATICAL ENGINEERING TECHNICAL REPORTS

    E-Print Network [OSTI]

    Yamamoto, Hirosuke

    MATHEMATICAL ENGINEERING TECHNICAL REPORTS Modeling of Contagious Credit Events and Risk Analysis holder. #12;Modeling of Contagious Credit Events and Risk Analysis of Credit Portfolios Suguru YAMANAKA This paper presents a new model of the intensities of contagious credit events such as rating changes

  8. Final Technical Report: Development of Post?Installation Monitoring Capabilities

    SciTech Connect (OSTI)

    Polagye, Brian [University of Washington] [University of Washington

    2014-03-31T23:59:59.000Z

    The development of approaches to harness marine and hydrokinetic energy at large?scale is predicated on the compatibility of these generation technologies with the marine environment. At present, aspects of this compatibility are uncertain. Demonstration projects provide an opportunity to address these uncertainties in a way that moves the entire industry forward. However, the monitoring capabilities to realize these advances are often under?developed in comparison to the marine and hydrokinetic energy technologies being studied. Public Utility District No. 1 of Snohomish County has proposed to deploy two 6?meter diameter tidal turbines manufactured by OpenHydro in northern Admiralty Inlet, Puget Sound, Washington. The goal of this deployment is to provide information about the environmental, technical, and economic performance of such turbines that can advance the development of larger?scale tidal energy projects, both in the United States and internationally. The objective of this particular project was to develop environmental monitoring plans in collaboration with resource agencies, while simultaneously advancing the capabilities of monitoring technologies to the point that they could be realistically implemented as part of these plans. In this, the District was joined by researchers at the Northwest National Marine Renewable Energy Center at the University of Washington, Sea Mammal Research Unit, LLC, H.T. Harvey & Associates, and Pacific Northwest National Laboratory. Over a two year period, the project team successfully developed four environmental monitoring and mitigation plans that were adopted as a condition of the operating license for the demonstration project that issued by the Federal Energy Regulatory Commission in March 2014. These plans address nearturbine interactions with marine animals, the sound produced by the turbines, marine mammal behavioral changes associated with the turbines, and changes to benthic habitat associated with colonization of the subsea base support structure. In support of these plans, the project team developed and field tested a strobe?illuminated stereooptical camera system suitable for studying near?turbine interactions with marine animals. The camera system underwent short?term field testing at the proposed turbine deployment site and a multi?month endurance test in shallower water to evaluate the effectiveness of biofouling mitigation measures for the optical ports on camera and strobe pressure housings. These tests demonstrated that the camera system is likely to meet the objectives of the near?turbine monitoring plan and operate, without maintenance, for periods of at least three months. The project team also advanced monitoring capabilities related to passive acoustic monitoring of marine mammals and monitoring of tidal currents. These capabilities will be integrated in a recoverable monitoring package that has a single interface point with the OpenHydro turbines, connects to shore power and data via a wet?mate connector, and can be recovered to the surface for maintenance and reconfiguration independent of the turbine. A logical next step would be to integrate these instruments within the package, such that one instrument can trigger the operation of another.

  9. TECHNICAL STANDARDS PROGRAM TOPICAL COMMITTEES

    Broader source: Energy.gov [DOE]

    PurposeThis procedure describes how topical committees are organized and recognized under the Technical Standards Program. 

  10. 1998 federal technical standards workshop: Proceedings

    SciTech Connect (OSTI)

    NONE

    1998-10-01T23:59:59.000Z

    The theme for the 1998 workshop was Standards Management -- A World of Change and Opportunities. The workshop`s goal was to further the implementation of the National Technology Transfer and Advancement Act of 1995 (Public Law 104-113) through the sharing of standards management success stories, lessons learned, and emerging initiatives within the Executive Branch of the Federal Government. The target audience for this workshop included agency/department and contractor personnel and representatives of standards developing organizations that either used technical standards in their work for the Federal Government of participated in standards writing/management activities in support of the missions and programs of Federal agencies/departments. As with previous standards workshops sponsored by the DOE, views on the technical subject areas under the workshop theme were solicited from and provided by agency Standards Executives and standards program managers, voluntary standards organizations, and the private sector. This report includes vugraphs of the presentations.

  11. Regulatory and technical reports (abstract index journal): Annual compilation for 1994. Volume 19, Number 4

    SciTech Connect (OSTI)

    NONE

    1995-03-01T23:59:59.000Z

    This compilation consists of bibliographic data and abstracts for the formal regulatory and technical reports issued by the US Nuclear Regulatory Commission (NRC) Staff and its contractors. It is NRC`s intention to publish this compilation quarterly and to cumulate it annually. The main citations and abstracts in this compilation are listed in NUREG number order. These precede the following indexes: secondary report number index, personal author index, subject index, NRC originating organization index (staff reports), NRC originating organization index (international agreements), NRC contract sponsor index (contractor reports), contractor index, international organization index, and licensed facility index. A detailed explanation of the entries precedes each index.

  12. Business Case for Technical Qualification Program Accreditation...

    Broader source: Energy.gov (indexed) [DOE]

    Business Case for Technical Qualification Program Accreditation Incentives Business Case for Technical Qualification Program Accreditation Incentives TQP Accreditation standardize...

  13. Technical basis for the aboveground structure failure accident & associated represented hazardous conditions

    SciTech Connect (OSTI)

    GOETZ, T.G.

    2003-05-15T23:59:59.000Z

    This technical basis document describes the risk binning process and the technical basis for assigning risk bins for the above-ground structure failure representative accident and associated represented hazardous conditions. This document was developed to support the documented safety analysis.

  14. Solar water heating technical support. Technical report for November 1997--April 1998 and final report

    SciTech Connect (OSTI)

    Huggins, J.

    1998-10-01T23:59:59.000Z

    This progress report covers the time period November 1, 1997 through April 30, 1998, and also summarizes the project as the final report. The topics of the report include certification of solar collectors for water heating systems, modeling and testing of solar collectors and gas water heater backup systems, ratings of collectors for specific climates, and solar pool heating systems.

  15. Deployment support leading to implementation

    SciTech Connect (OSTI)

    NONE

    1999-11-01T23:59:59.000Z

    This quarterly report discusses progress on the following tasks and subtasks: (Task 1)--Field demonstration of prefabricated vertical drains (PVD) technology: Subtask 1.1--Pilot scale demonstration of TCE flushing through PVDs at the DOE/RMI Extrusion Plant; Subtask 1.2--Technical support on surfactants and QA/QC for field operations employing PVDs at the RMI Ashtabula, Ohio, site; Subtask 1.3--Operational support of the PVDs and engineering/design/construction/operations of a wastewater treatment plant for extracted fluids; Subtask 1.4--Installation of PVDs at the RMI Ashtabulah, Ohio, site; and Subtask 1.5--Removal of surfactants and trichloroethylene (TCE) from extracted groundwater at the RMI Ashtabula, Ohio, site; (Task 2)--Watershed economics and overview studies; and (Task 3)--Project management.

  16. Slide04 | OSTI, US Dept of Energy, Office of Scientific and Technical...

    Office of Scientific and Technical Information (OSTI)

    * Support * Assist * Partner * Equals Success * OSTI and the Labs are partners in making scientific and technical information available. * 30.7 million Full-Text Downloads in FY09...

  17. Hanford site solid waste management environmental impact statement technical information document [SEC 1 THRU 4

    SciTech Connect (OSTI)

    FRITZ, L.L.

    2003-04-01T23:59:59.000Z

    This Technical Information Document (TID) provides engineering data to support DOE/EIS-0286, ''Hanford Site Solid (Radioactive and Hazardous) Waste Program Environmental Impact Statement,'' including assumptions and waste volumes calculation data.

  18. Final Technical Report

    SciTech Connect (OSTI)

    Maxwell, Mike, J., P.E.

    2012-08-30T23:59:59.000Z

    The STI product is the Final Technical Report from ReliOn, Inc. for contract award DE-EE0000487: Recovery Act PEM Fuel Cell Systems Providing Emergency Reserve and Backup Power. The program covered the turnkey deployment of 431 ReliOn fuel cell systems at 189 individual sites for AT&T and PG&E with ReliOn functioning as the primary equipment supplier and the project manager. The Final Technical Report provides an executive level summary, a comparison of the actual accomplishments vs. the goals and objectives of the project, as well as a summary of the project activity from the contract award date of August 1, 2009 through the contract expiration date of December 31, 2011. Two photos are included in the body of the report which show hydrogen storage and bulk hydrogen refueling technologies developed as a result of this program.

  19. Partial Support for the Federal Committee for Meteorological Services and Supporting Research

    SciTech Connect (OSTI)

    Williamson, Samuel P

    2012-04-30T23:59:59.000Z

    DOE E-link Report Number DOE/ER62778 1999-2012 Please see attached Final Technical Report (size too large to post here). Annual Products Provided to DOE: Federal Plan for Meteorological Services and Supporting Research; National Hurricane Operations Plan; Interdepartmental Hurricane Conference Summary Report. All reports and publications can be found on the OFCM website, www.ofcm.noaa.gov.

  20. Technical Surveillance Countermeasures Program

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1993-06-18T23:59:59.000Z

    To prescribe policies, responsibilities and authorities to establish Department of Energy (DOE) Technical Surveillance Countermeasures (TSCM) Program. This order implements the DOE TSCM Procedural Guide, DOE TSCM Operations Manual, DOE TSCM Report Writing Guide and Threat Assessment Scheduling System (TASS) which contain classified policies and procedures concerning the DOE TSCM Program. Cancels DOE 5636.3A. Canceled by DOE O 471.2 dated 9-28-95.

  1. Technical approach document

    SciTech Connect (OSTI)

    Not Available

    1989-12-01T23:59:59.000Z

    The Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978, Public Law 95-604 (PL95-604), grants the Secretary of Energy the authority and responsibility to perform such actions as are necessary to minimize radiation health hazards and other environmental hazards caused by inactive uranium mill sites. This Technical Approach Document (TAD) describes the general technical approaches and design criteria adopted by the US Department of Energy (DOE) in order to implement remedial action plans (RAPS) and final designs that comply with EPA standards. It does not address the technical approaches necessary for aquifer restoration at processing sites; a guidance document, currently in preparation, will describe aquifer restoration concerns and technical protocols. This document is a second revision to the original document issued in May 1986; the revision has been made in response to changes to the groundwater standards of 40 CFR 192, Subparts A--C, proposed by EPA as draft standards. New sections were added to define the design approaches and designs necessary to comply with the groundwater standards. These new sections are in addition to changes made throughout the document to reflect current procedures, especially in cover design, water resources protection, and alternate site selection; only minor revisions were made to some of the sections. Sections 3.0 is a new section defining the approach taken in the design of disposal cells; Section 4.0 has been revised to include design of vegetated covers; Section 8.0 discusses design approaches necessary for compliance with the groundwater standards; and Section 9.0 is a new section dealing with nonradiological hazardous constituents. 203 refs., 18 figs., 26 tabs.

  2. To appear, WEDA 29th Technical Conference & 40th

    E-Print Network [OSTI]

    US Army Corps of Engineers

    To appear, WEDA 29th Technical Conference & 40th TAMU Dredging Seminar, in press, 2009 DEPTH-UTILIZATION ANALYSIS FOR ESTIMATING ECONOMIC ACTIVITY SUPPORTED BY DREDGING Kenneth N. Mitchell1 and James E. Walker2 of dollars annually towards operation and maintenance, primarily dredging, of federal channels and waterways

  3. D.C. Water Resources Research Center Annual Technical Report

    E-Print Network [OSTI]

    and among agencies, universities, and other area researchers; and to support the development and Guidelines under the Water Resources Development Act, and other federal spending and activities relatedD.C. Water Resources Research Center Annual Technical Report FY 2009 D.C. Water Resources Research

  4. Kentucky Water Resources Research Institute Annual Technical Report

    E-Print Network [OSTI]

    development for pH, nutrients, and pathogens in several Kentucky streams, 2) Evaluation of the impacts of Environmental Health (NIEH), and east Kentucky PRIDE (Personal Responsibility in a Desirable Environment): 1) Environmental Protection Scholarship (NREPC), 2) Technical support for the Maxey Flats Nuclear Disposal Site

  5. Oklahoma Water Resources Research Institute Annual Technical Report

    E-Print Network [OSTI]

    Resources Board. Decision Support System for Long Term Planning of Rural and Urban Water Supply Systems CostOklahoma Water Resources Research Institute Annual Technical Report FY 2006 #12;Introduction developing the natural environment. The Oklahoma Water Resources Research Institute (OWRRI), located within

  6. Oklahoma Water Resources Research Institute Annual Technical Report

    E-Print Network [OSTI]

    Oklahoma Water Resources Research Institute Annual Technical Report FY 2004 Introduction The Environmental Institute at Oklahoma State University has as its mission to serve as a center for stimulation, protecting, utilizing and sustaining the natural environment. The federally supported Oklahoma Water

  7. Kentucky Water Resources Research Institute Annual Technical Report

    E-Print Network [OSTI]

    on environmental assessment and cleanup evaluation at the Paducah Gaseous Diffusion Plant over the next several for Health Services (Technical Support for the Maxey Flats Nuclear Disposal Site and the Paducah Gaseous Diffusion Plant Federal Facilities Agreement and Agreement in Principle), the Kentucky Department

  8. Kentucky Water Resources Research Institute Annual Technical Report

    E-Print Network [OSTI]

    Flats Disposal Site (CHS) 2) Technical support for the Paducah Gaseous Diffusion Plant (CHS) 3 soils and paleowetland sediments in the vicinity of the Paducah Gaseous Diffusion Plant (PGDP) to bind Attenuation of a Trichloroethene-Contaminated Aquifer System, Paducah, Kentucky, MS Thesis, Department

  9. The Control Technical Reference Model Holger A. Dippel

    E-Print Network [OSTI]

    Michel, Howard E.

    TRM is the International Organization for Standardization's (ISO) Open Systems Interconnection (OSI for computer networks, the International Organization for Standardization (ISO) formed a #12;subcommittee (SC16 component-driven, technical framework categorizing the standards and technologies to support and enable

  10. Burnup Credit Approach Used in the Yucca Mountain License Application

    SciTech Connect (OSTI)

    Scaglione, John M [ORNL] [ORNL; Wagner, John C [ORNL] [ORNL

    2010-01-01T23:59:59.000Z

    The United States Department of Energy has submitted a license application (LA) for construction authorization of a deep geologic repository at Yucca Mountain, Nevada. The license application is currently under review by the United States Nuclear Regulatory Commission (NRC). This paper will describe the methodology and approach used in the LA to address the issue of criticality and the role of burnup credit during the postclosure period. The most significant and effective measures for prevention of criticality in the repository include multiple redundant barriers that act to isolate fissionable material from water (which can act as a moderator, corrosive agent, and transporter of fissile material); inherent geometry of waste package internals and waste forms; presence of fixed neutron absorbers in waste package internals; and fuel burnup for commercial spent nuclear fuel. A probabilistic approach has been used to screen criticality from the total system performance assessment. Within the probabilistic approach, criticality is considered an event, and the total probability of a criticality event occurring within 10,000 years of disposal is calculated and compared against the regulatory criterion. The total probability of criticality includes contributions associated with both internal (within waste packages) and external (external to waste packages) criticality for each of the initiating events that could lead to waste package breach. The occurrence of and conditions necessary for criticality in the repository have been thoroughly evaluated using a comprehensive range of parameter distributions. A simplified design-basis modeling approach has been used to evaluate the probability of criticality by using numerous significant and conservative assumptions. Burnup credit is used only for evaluations of in-package configurations and uses a combination of conservative and bounding modeling approximations to ensure conservatism. This paper will review the NRC regulatory criteria relevant to postclosure criticality, explain the role of criticality within the overall repository performance assessment, describe the strategy for preventing criticality via design features and waste form properties, and discuss the numerous considerations relevant to criticality and burnup credit for spent nuclear fuel disposed of in a geologic repository, with emphasis on the burnup credit approach and analyses.

  11. Model and Analytic Processes for Export License Assessments

    SciTech Connect (OSTI)

    Thompson, Sandra E.; Whitney, Paul D.; Weimar, Mark R.; Wood, Thomas W.; Daly, Don S.; Brothers, Alan J.; Sanfilippo, Antonio P.; Cook, Diane; Holder, Larry

    2011-09-29T23:59:59.000Z

    This paper represents the Department of Energy Office of Nonproliferation Research and Development (NA-22) Simulations, Algorithms and Modeling (SAM) Program's first effort to identify and frame analytical methods and tools to aid export control professionals in effectively predicting proliferation intent; a complex, multi-step and multi-agency process. The report focuses on analytical modeling methodologies that alone, or combined, may improve the proliferation export control license approval process. It is a follow-up to an earlier paper describing information sources and environments related to international nuclear technology transfer. This report describes the decision criteria used to evaluate modeling techniques and tools to determine which approaches will be investigated during the final 2 years of the project. The report also details the motivation for why new modeling techniques and tools are needed. The analytical modeling methodologies will enable analysts to evaluate the information environment for relevance to detecting proliferation intent, with specific focus on assessing risks associated with transferring dual-use technologies. Dual-use technologies can be used in both weapons and commercial enterprises. A decision-framework was developed to evaluate which of the different analytical modeling methodologies would be most appropriate conditional on the uniqueness of the approach, data availability, laboratory capabilities, relevance to NA-22 and Office of Arms Control and Nonproliferation (NA-24) research needs and the impact if successful. Modeling methodologies were divided into whether they could help micro-level assessments (e.g., help improve individual license assessments) or macro-level assessment. Macro-level assessment focuses on suppliers, technology, consumers, economies, and proliferation context. Macro-level assessment technologies scored higher in the area of uniqueness because less work has been done at the macro level. An approach to developing testable hypotheses for the macro-level assessment methodologies is provided. The outcome of this works suggests that we should develop a Bayes Net for micro-level analysis and continue to focus on Bayes Net, System Dynamics and Economic Input/Output models for assessing macro-level problems. Simultaneously, we need to develop metrics for assessing intent in export control, including the risks and consequences associated with all aspects of export control.

  12. Standard technical specifications: Combustion engineering plants. Volume 1, Revision 1: Specifications

    SciTech Connect (OSTI)

    NONE

    1995-04-01T23:59:59.000Z

    This report documents the results of the combined effort of the NRC and the industry to produce improved Standard Technical Specifications (STS), Revision 1 for Combustion Engineering Plants. The changes reflected in Revision 1 resulted from the experience gained from license amendment applications to convert to these improved STS or to adopt partial improvements to existing technical specifications. This NUREG is the result of extensive public technical meetings and discussions between the Nuclear Regulatory Commission (NRC) staff and various nuclear power plant licensees, Nuclear Steam Supply System (NSSS) Owners Groups, NSSS vendors, and the Nuclear Energy Institute (NEI). The improved STS were developed based on the criteria in the Final Commission Policy Statement on Technical Specifications Improvements for Nuclear Power Reactors, dated July 22, 1993. The improved STS will be used as the basis for individual nuclear power plant licensees to develop improved plant-specific technical specifications. This report contains three volumes. Volume 1 contains the Specifications for all chapters and sections of the improved STS. Volume 2 contains the Bases for Chapters 2.0 and 3.0, and Sections 3.1--3.3 of the improved STS. Volume 3 contains the Bases for Sections 3.4--3.9 of the improved STS.

  13. Licensing and Deployment of Advanced Reactors Andrew C. Kadak, Ph.D.

    E-Print Network [OSTI]

    of advanced reactors of the type proposed for Generation IV will require a new strategy for licensing since many of the proposed Generation IV technologies include concepts such as high temperature gas

  14. Pricing and licensing of software products and services : a study on industry trends

    E-Print Network [OSTI]

    Nayak, Shivashis

    2006-01-01T23:59:59.000Z

    The software product business reached the $150 billion mark at the end of 2005. The pricing and licensing of new products, maintenance services, services and service maintenance have become an important strategy to deliver ...

  15. Atomic Energy and Radioactive Substances: Licensing and Regulation of Sites: The Nuclear Installations Regulations, 1962 

    E-Print Network [OSTI]

    Wood, Richard; Maclay, John. S.

    1962-01-01T23:59:59.000Z

    These regulations, made by the Minister of Power and the Secretary of State for Scotland acting jointly, prescribe for the purpose of subsection (1)(b) of section one of the Nuclear Installations (Licensing and Insurance) Act, 1959, certain classes...

  16. Better Lucky Than Rich? Welfare Analysis of Automobile License Allocations in Beijing and Shanghai

    E-Print Network [OSTI]

    Schweik, Charles M.

    Better Lucky Than Rich? Welfare Analysis of Automobile License Allocations in Beijing and Shanghai externalities from automobile use than a uniform price auction, the advantage is offset by the significant automobile sales in China grew from 2.4 millio

  17. Photovoltaics at DOE's National Renewable Energy Laboratory License...

    Office of Environmental Management (EM)

    INSTALLATION AND OPERATION OF A SOLAR ROOF-TOP ELECTRIC GENERATING SYSTEM AT THE NATIONAL RENEWABLE ENERGY LABORATORY, RESEARCH SUPPORT FACILITY United States of America Department...

  18. Proceedings: Decommissioning--License Termination Plans and Final Site Release Workshop

    SciTech Connect (OSTI)

    None

    2004-03-01T23:59:59.000Z

    This report presents the proceedings of an EPRI workshop dealing with the subject of decommissioning license termination and final site release. The workshop was the ninth in a series designed to aid utility personnel in assessing technologies for decommissioning nuclear power plants. It focused on specific aspects of license termination activities and final site release as they relate to nuclear plant decommissioning. The information presented will help utilities control decommissioning costs by selecting the best practices and technologies

  19. A hierarchical structure of neural network implemented for the recognition of automobile license plate number

    E-Print Network [OSTI]

    Chang, Joongho

    1994-01-01T23:59:59.000Z

    A HIERARCHICAL STRUCTURE OF NEURAL NETWORK IMPLEMENTED FOR THE RECOGNITION OF AUTOMOBILE LICENSE PLATE NURSER A Thesis by JOONGHO CHANG Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfdlment... of the requirements for the degree of MASTER OF SCIENCE August 1994 Major Subject: Electrical Engineering A HIERARCHICAL STRUCTURE OF NEURAL NETWORK IMPLEMENTED FOR THE RECOGNITION OF AUTOMOBILE LICENSE PLATE NUMBER A Thesis by JOONGHO CHANG Submitted...

  20. Sodium fast reactor safety and licensing research plan. Volume II.

    SciTech Connect (OSTI)

    Ludewig, H. (Brokhaven National Laboratory, Upton, NY); Powers, D. A.; Hewson, John C.; LaChance, Jeffrey L.; Wright, A. (Argonne National Laboratory, Argonne, IL); Phillips, J.; Zeyen, R. (Institute for Energy Petten, Saint-Paul-lez-Durance, France); Clement, B. (IRSN/DPAM.SEMIC Bt 702, Saint-Paul-lez-Durance, France); Garner, Frank (Radiation Effects Consulting, Richland, WA); Walters, Leon (Advanced Reactor Concepts, Los Alamos, NM); Wright, Steve; Ott, Larry J. (Oak Ridge National Laboratory, Oak Ridge, TN); Suo-Anttila, Ahti Jorma; Denning, Richard (Ohio State University, Columbus, OH); Ohshima, Hiroyuki (Japan Atomic Energy Agency, Ibaraki, Japan); Ohno, S. (Japan Atomic Energy Agency, Ibaraki, Japan); Miyhara, S. (Japan Atomic Energy Agency, Ibaraki, Japan); Yacout, Abdellatif (Argonne National Laboratory, Argonne, IL); Farmer, M. (Argonne National Laboratory, Argonne, IL); Wade, D. (Argonne National Laboratory, Argonne, IL); Grandy, C. (Argonne National Laboratory, Argonne, IL); Schmidt, R.; Cahalen, J. (Argonne National Laboratory, Argonne, IL); Olivier, Tara Jean; Budnitz, R. (Lawrence Berkeley National Laboratory, Berkeley, CA); Tobita, Yoshiharu (Japan Atomic Energy Agency, Ibaraki, Japan); Serre, Frederic (Centre d'%C3%94etudes nucl%C3%94eaires de Cadarache, Cea, France); Natesan, Ken (Argonne National Laboratory, Argonne, IL); Carbajo, Juan J. (Oak Ridge National Laboratory, Oak Ridge, TN); Jeong, Hae-Yong (Korea Atomic Energy Research Institute, Daejeon, Korea); Wigeland, Roald (Idaho National Laboratory, Idaho Falls, ID); Corradini, Michael (University of Wisconsin-Madison, Madison, WI); Thomas, Justin (Argonne National Laboratory, Argonne, IL); Wei, Tom (Argonne National Laboratory, Argonne, IL); Sofu, Tanju (Argonne National Laboratory, Argonne, IL); Flanagan, George F. (Oak Ridge National Laboratory, Oak Ridge, TN); Bari, R. (Brokhaven National Laboratory, Upton, NY); Porter D. (Idaho National Laboratory, Idaho Falls, ID); Lambert, J. (Argonne National Laboratory, Argonne, IL); Hayes, S. (Idaho National Laboratory, Idaho Falls, ID); Sackett, J. (Idaho National Laboratory, Idaho Falls, ID); Denman, Matthew R.

    2012-05-01T23:59:59.000Z

    Expert panels comprised of subject matter experts identified at the U.S. National Laboratories (SNL, ANL, INL, ORNL, LBL, and BNL), universities (University of Wisconsin and Ohio State University), international agencies (IRSN, CEA, JAEA, KAERI, and JRC-IE) and private consultation companies (Radiation Effects Consulting) were assembled to perform a gap analysis for sodium fast reactor licensing. Expert-opinion elicitation was performed to qualitatively assess the current state of sodium fast reactor technologies. Five independent gap analyses were performed resulting in the following topical reports: (1) Accident Initiators and Sequences (i.e., Initiators/Sequences Technology Gap Analysis), (2) Sodium Technology Phenomena (i.e., Advanced Burner Reactor Sodium Technology Gap Analysis), (3) Fuels and Materials (i.e., Sodium Fast Reactor Fuels and Materials: Research Needs), (4) Source Term Characterization (i.e., Advanced Sodium Fast Reactor Accident Source Terms: Research Needs), and (5) Computer Codes and Models (i.e., Sodium Fast Reactor Gaps Analysis of Computer Codes and Models for Accident Analysis and Reactor Safety). Volume II of the Sodium Research Plan consolidates the five gap analysis reports produced by each expert panel, wherein the importance of the identified phenomena and necessities of further experimental research and code development were addressed. The findings from these five reports comprised the basis for the analysis in Sodium Fast Reactor Research Plan Volume I.

  1. Clean Energy Innovation: Sources of Technical and Commercial Breakthroughs

    SciTech Connect (OSTI)

    Perry, T. D., IV; Miller, M.; Fleming, L.; Younge, K.; Newcomb, J.

    2011-03-01T23:59:59.000Z

    Low-carbon energy innovation is essential to combat climate change, promote economic competitiveness, and achieve energy security. Using U.S. patent data and additional patent-relevant data collected from the Internet, we map the landscape of low-carbon energy innovation in the United States since 1975. We isolate 10,603 renewable and 10,442 traditional energy patents and develop a database that characterizes proxy measures for technical and commercial impact, as measured by patent citations and Web presence, respectively. Regression models and multivariate simulations are used to compare the social, institutional, and geographic drivers of breakthrough clean energy innovation. Results indicate statistically significant effects of social, institutional, and geographic variables on technical and commercial impacts of patents and unique innovation trends between different energy technologies. We observe important differences between patent citations and Web presence of licensed and unlicensed patents, indicating the potential utility of using screened Web hits as a measure of commercial importance. We offer hypotheses for these revealed differences and suggest a research agenda with which to test these hypotheses. These preliminary findings indicate that leveraging empirical insights to better target research expenditures would augment the speed and scale of innovation and deployment of clean energy technologies.

  2. Technical safety requirements control level verification

    SciTech Connect (OSTI)

    STEWART, J.L.

    1999-05-21T23:59:59.000Z

    A Technical Safety Requirement (TSR) control level verification process was developed for the Tank Waste Remediation System (TWRS) TSRs at the Hanford Site in Richland, WA, at the direction of the US. Department of Energy, Richland Operations Office (RL). The objective of the effort was to develop a process to ensure that the TWRS TSR controls are designated and managed at the appropriate levels as Safety Limits (SLs), Limiting Control Settings (LCSs), Limiting Conditions for Operation (LCOs), Administrative Controls (ACs), or Design Features. The TSR control level verification process was developed and implemented by a team of contractor personnel with the participation of Fluor Daniel Hanford, Inc. (FDH), the Project Hanford Management Contract (PHMC) integrating contractor, and RL representatives. The team was composed of individuals with the following experience base: nuclear safety analysis; licensing; nuclear industry and DOE-complex TSR preparation/review experience; tank farm operations; FDH policy and compliance; and RL-TWRS oversight. Each TSR control level designation was completed utilizing TSR control logic diagrams and TSR criteria checklists based on DOE Orders, Standards, Contractor TSR policy, and other guidance. The control logic diagrams and criteria checklists were reviewed and modified by team members during team meetings. The TSR control level verification process was used to systematically evaluate 12 LCOs, 22 AC programs, and approximately 100 program key elements identified in the TWRS TSR document. The verification of each TSR control required a team consensus. Based on the results of the process, refinements were identified and the TWRS TSRs were modified as appropriate. A final report documenting key assumptions and the control level designation for each TSR control was prepared and is maintained on file for future reference. The results of the process were used as a reference in the RL review of the final TWRS TSRs and control suite. RL concluded that the TSR control level verification process is clear and logically based upon DOE Order 5480.22, Technical Safety Requirements, and other TSR control selection guidelines. The process provides a documented, traceable basis for TSR level decisions and is a valid reference for preparation of new TSRs.

  3. Draft 1992 Resource Program : Technical Report.

    SciTech Connect (OSTI)

    United States. Bonneville Power Administration.

    1992-01-01T23:59:59.000Z

    The 1992 Resource Program will propose actions to meet future loads placed on the Bonneville Power Administration (BPA). It will also discuss and attempt to resolve resource-related policy issues. The Resource Program assesses resource availability and costs, and analyzes resource requirements and alternative ways of meeting those requirements through both conservation and generation resources. These general resource conclusions are then translated to actions for both conservation and generation. The Resource Program recommends budgets for the Office of Energy Resources for Fiscal Years (FY) 1994 and 1995. BPA's Resource Program bears directly on an important BPA responsibility: the obligation under the Northwest Power Act{sup 3} to meet the power requirements of public and private utility and direct service industrial (DSI) customers according to their contractual agreements. BPA's Draft 1992 Resource Program is contained in four documents: (1) 1992 Resource Program Summary; (2) Technical Report; (3) Technical Assumptions Appendix; and, (4) Conservation Implementation Plan. This volume is the Draft 1992 Resource Program Technical Report, a comprehensive document that provides supporting data and analyses for Resource Program recommendations.

  4. Draft 1992 Resource Program : Technical Report.

    SciTech Connect (OSTI)

    United States. Bonneville Power Administration.

    1992-01-01T23:59:59.000Z

    The 1992 Resource Program will propose actions to meet future loads placed on the Bonneville Power Administration (BPA). It will also discuss and attempt to resolve resource-related policy issues. The Resource Program assesses resource availability and costs, and analyzes resource requirements and alternative ways of meeting those requirements through both conservation and generation resources. These general resource conclusions are then translated to actions for both conservation and generation. The Resource Program recommends budgets for the Office of Energy Resources for Fiscal Years (FY) 1994 and 1995. BPA`s Resource Program bears directly on an important BPA responsibility: the obligation under the Northwest Power Act{sup 3} to meet the power requirements of public and private utility and direct service industrial (DSI) customers according to their contractual agreements. BPA`s Draft 1992 Resource Program is contained in four documents: (1) 1992 Resource Program Summary; (2) Technical Report; (3) Technical Assumptions Appendix; and, (4) Conservation Implementation Plan. This volume is the Draft 1992 Resource Program Technical Report, a comprehensive document that provides supporting data and analyses for Resource Program recommendations.

  5. RADTRAN 6 technical manual.

    SciTech Connect (OSTI)

    Weiner, Ruth F.; Neuhauser, Karen Sieglinde; Heames, Terence John; O'Donnell, Brandon M.; Dennis, Matthew L.

    2014-01-01T23:59:59.000Z

    This Technical Manual contains descriptions of the calculation models and mathematical and numerical methods used in the RADTRAN 6 computer code for transportation risk and consequence assessment. The RADTRAN 6 code combines user-supplied input data with values from an internal library of physical and radiological data to calculate the expected radiological consequences and risks associated with the transportation of radioactive material. Radiological consequences and risks are estimated with numerical models of exposure pathways, receptor populations, package behavior in accidents, and accident severity and probability.

  6. Boiler MACT Technical Assistance

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: The FutureCommentsEnergyandapproximately 10|BlueFireBoiler MACT Technical

  7. Final Technical Report

    SciTech Connect (OSTI)

    Sobecky, Patricia A; Taillefert, Martial

    2013-03-29T23:59:59.000Z

    This final technical report describes results and findings from a research project to examine the role of microbial phosphohydrolase enzymes in naturally occurring subsurface microorganisms for the purpose of promoting the immobilization of the radionuclide uranium through the production of insoluble uranium phosphate minerals. The research project investigated the microbial mechanisms and the physical and chemical processes promoting uranium biomineralization and sequestration in oxygenated subsurface soils. Uranium biomineralization under aerobic conditions can provide a secondary biobarrier strategy to immobilize radionuclides should the metal precipitates formed by microbial dissimilatory mechanisms remobilize due to a change in redox state.

  8. SPEAR3 | Technical Documentation

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What's PossibleRadiation Protection245C Unlimited ReleaseWelcome ton n u a l r e p o Technical

  9. Technical Review Panel Report

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33Frequently AskedEnergyIssuesEnergy Solar Decathlon | DepartmentEnergyOffice -TechnicalTRP

  10. External Technical Review Report

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 111 1,613 122Commercial602 1,39732 DOEDepartment of EnergyEric J.ExploringExternal Technical

  11. ARM - Technical Reports

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItem NotEnergy,ARMForms About Become a UsergovAboutRecoverygovPublicationsTechnical

  12. Mechanical Engineering Department Technical Review

    SciTech Connect (OSTI)

    Carr, R.B.; Denney, R.M. (eds.)

    1981-07-01T23:59:59.000Z

    The Mechanical Engineering Department Technical Review is published to inform readers of various technical activities within the Department, promote exchange of ideas, and give credit to personnel who are achieving the results. The report is presented in two parts: technical achievements and publication abstracts. The first is divided into seven sections, each of which reports on an engineering division and its specific activities related to nuclear tests, nuclear explosives, weapons, energy systems, engineering sciences, magnetic fusion, and materials fabrication.

  13. Mechanical Engineering Department technical abstracts

    SciTech Connect (OSTI)

    Denney, R.M. (ed.)

    1982-07-01T23:59:59.000Z

    The Mechanical Engineering Department publishes listings of technical abstracts twice a year to inform readers of the broad range of technical activities in the Department, and to promote an exchange of ideas. Details of the work covered by an abstract may be obtained by contacting the author(s). Overall information about current activities of each of the Department's seven divisions precedes the technical abstracts.

  14. Mechanical engineering department technical review

    SciTech Connect (OSTI)

    Carr, R.B. Denney, R.M. (eds.)

    1981-01-01T23:59:59.000Z

    The Mechanical Engineering Department Technical Review is published to: (1) inform the readers of various technical activities within the department, (2) promote exchange of ideas, and (3) give credit to the personnel who are achieving the results. The report is formatted into two parts: technical acievements and publication abstracts. The first is divided into eight sections, one for each division in the department providing the reader with the names of the personnel and the division accomplishing the work.

  15. Scientific and Technical Information Management

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2003-10-14T23:59:59.000Z

    The Order establishes requirements and responsibilities for managing DOE's scientific and technical information. Cancels DOE O 241.1. Canceled by DOE O 241.1B.

  16. Technical Services | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    noteworthy for their unique technical capabilities: Central Shops facility performs welding and brazing for high-vacuum applications, machining of radioactive materials, and a...

  17. Hydrogen Storage Technical Team Roadmap

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    and technology pathways are impacted by their analyses. These technical teams include Fuel Cells, Fuel Pathway Integration, Hydrogen Delivery, Hydrogen Production, Materials,...

  18. APS Technical Systems Monitoring Page

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Photon Source Technical Systems Accelerator Systems Storage Ring Status for the past 24 hours with real Time of Day User beam delineated. Current, Lifetime, History with 24-hr...

  19. Document: P1332 Category: Physical Sciences, Chemical/Materials License Status: Available for licensing Texas Industry Cluster: Petroleum Refining & Chemical Products

    E-Print Network [OSTI]

    Lightsey, Glenn

    for licensing Texas Industry Cluster: Petroleum Refining & Chemical Products Lower-cost fuel cells Problem, and they offer an alternative to petroleum-burning internal combustion engines. The U.S. Environ- mental and as a replacement for off-grid small power and grid production power plants. Development Stage/IP Status Lab

  20. MILITARY TECHNICAL ACADEMY Vol. XXII, No. 4

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    #12;MILITARY TECHNICAL ACADEMY Vol. XXII, No. 4 © Military Technical Academy Publishing House Technical Academy of Bucharest, Romania Col. Prof. Eng. IOAN NICOLAESCU, Ph.D. The Military Technical Academy of Bucharest, Romania Prof. Eng. VICTOR-VALERIU PATRICIU, Ph.D. The Military Technical Academy

  1. Primer Control System Cyber Security Framework and Technical Metrics

    SciTech Connect (OSTI)

    Wayne F. Boyer; Miles A. McQueen

    2008-05-01T23:59:59.000Z

    The Department of Homeland Security National Cyber Security Division supported development of a control system cyber security framework and a set of technical metrics to aid owner-operators in tracking control systems security. The framework defines seven relevant cyber security dimensions and provides the foundation for thinking about control system security. Based on the developed security framework, a set of ten technical metrics are recommended that allow control systems owner-operators to track improvements or degradations in their individual control systems security posture.

  2. Technical background document for soil screening guidance. Review draft

    SciTech Connect (OSTI)

    Not Available

    1994-12-01T23:59:59.000Z

    The document provides the technical background behind the development of the November 1994 Soil Screening Guidance for Superfund. These documents define the Soil Screening framework, a suite of methodologies for developing Soil Screening Levels (SSLs) for 107 chemicals commonly found at Superfund sites. The document is an updated version of the background document developed in support of the September 30, 1993, draft SSL guidance (PB93-963508). The document and the Guidance is available for public comment and is currently undergoing extensive peer review. Because the guidance is still under review, it and this document should not be used until they are finalized following this rigorous technical review and public comment.

  3. The Office of Environmental Management technical reports: a bibliography

    SciTech Connect (OSTI)

    NONE

    1997-07-01T23:59:59.000Z

    The Office of Environmental Management`s (EM) technical reports bibliography is an annual publication that contains information on scientific and technical reports sponsored by the Office of Environmental Management added to the Energy Science and Technology Database from July 1, 1995 through Sept. 30, 1996. This information is divided into the following categories: Focus Areas and Crosscutting Programs. Support Programs, Technology Integration and International Technology Exchange are now included in the General category. EM`s Office of Science and Technology sponsors this bibliography.

  4. Technical assistance contractor management plan: Surface and ground water

    SciTech Connect (OSTI)

    Not Available

    1994-09-01T23:59:59.000Z

    This report presents the general management structure of the Technical Assistance Contractor (TAC) for the Uranium Mill Tailings Remedial Action (UMTRA) Project. This team is a partnership of four major private subcontractors, which teamed together, are striving to be the leader in environmental restoration of uranium mining and milling operations. It will provide a pool of experts in various aspects of the technologies necessary to accomplish this goal, available to DOE to deal with mission concerns. The report expands on goals from TAC`s mission statement, which include management concerns, environment, safety, and health, quality, technical support, communications, and personnel.

  5. Technical Assistance Project for the Minnesota Pollution Control Agency

    SciTech Connect (OSTI)

    Vimmerstedt, L.

    2006-12-01T23:59:59.000Z

    This report was prepared in response to a request for technical assistance from the Minnesota Pollution Control Agency (MPCA). The U.S. Department of Energy's (DOE) Office of Energy Efficiency and Renewable Energy supported the National Renewable Energy Laboratory (NREL) in its response to this request through the Technical Assistance Project. Discussion with the MPCA identified the following as the highest-priority questions: What is the effect of (1) size of Renewable Energy Reserve (RER) and (2) duration of allocation award on (a) NOx emissions in Minnesota and (b) retail electricity prices? What data is available on the response of wind energy development to financial incentives? This report addresses those questions.

  6. Joint Technical Operations Team | National Nuclear Security Administra...

    National Nuclear Security Administration (NNSA)

    Render Safe Joint Technical Operations Team Joint Technical Operations Team JTOT Logo NNSA's Joint Technical Operations Team (JTOT) provides specialized technical...

  7. Nuclear Power 2010 Program Dominion Virginia Power Cooperative Project U.S. Department of Energy Cooperative Agreement DE-FC07-05ID14635 Construction and Operating License Demonstration Project Final Report

    SciTech Connect (OSTI)

    Eugene S. Grecheck

    2010-11-30T23:59:59.000Z

    This report serves to summarize the major activities completed as part of Virginia Electric and Power Company's North Anna construction and operating license demonstration project with DOE. Project successes, lessons learned, and suggestions for improvement are discussed. Objectives of the North Anna COL project included preparation and submittal of a COLA to the USNRC incorporating ESBWR technology for a third unit a the North Anna Power Station site, support for the NRC review process and mandatory hearing, obtaining NRC approval of the COLA and issuance of a COL, and development of a business case necessary to support a decision on building a new nuclear power plant at the North Anna site.

  8. The Persistence of Economic Factors in Shaping Regulation and Environmental Performance: The Limits of Regulation and Social License Pressures

    E-Print Network [OSTI]

    Thornton, Dorothy; Kagan, Robert; Gunningham, Neil

    2007-01-01T23:59:59.000Z

    license. That is, economic incentives drive the choice ofa company has strong economic incentives to buy new trucks.$/mile. While the similar economic incentives applied to all

  9. Texas Phosphorus Index TECHNICAL NOTES

    E-Print Network [OSTI]

    Mukhtar, Saqib

    for West Texas, see Figure 1. NRCS and Extension Service specialists in Texas developed the P indicesTexas Phosphorus Index TECHNICAL NOTES U.S. DEPARTMENT OF AGRICULTURE NATURAL RESOURCES CONSERVATION SERVICE TEXAS Revised December, 2012 AGRONOMY TECHNICAL NOTE NUMBER ­ 15 PHOSPHORUS ASSESSMENT

  10. Computer Science Department Technical Report

    E-Print Network [OSTI]

    Shahriar, Selim

    of computing #12;Virtuoso: A System for Virtual Machine Marketplaces Technical Report NWU-CS-04-39 Alex that presents the abstraction of a new raw physical machine on the buyer's network. This report describesComputer Science Department Technical Report NWU-CS-04-39 July 20, 2004 Virtuoso: A System

  11. Technical applications of aerogels

    SciTech Connect (OSTI)

    Hrubesh, L.W.

    1997-08-18T23:59:59.000Z

    Aerogel materials posses such a wide variety of exceptional properties that a striking number of applications have developed for them. Many of the commercial applications of aerogels such as catalysts, thermal insulation, windows, and particle detectors are still under development and new application as have been publicized since the ISA4 Conference in 1994: e.g.; supercapacitors, insulation for heat storage in automobiles, electrodes for capacitive deionization, etc. More applications are evolving as the scientific and engineering community becomes familiar with the unusual and exceptional physical properties of aerogels, there are also scientific and technical application, as well. This paper discusses a variety of applications under development at Lawrence Livermore National Laboratory for which several types of aerogels are formed in custom sizes and shapes. Particular discussions will focus on the uses of aerogels for physics experiments which rely on the exceptional, sometimes unique, properties of aerogels.

  12. FINAL/ SCIENTIFIC TECHNICAL REPORT

    SciTech Connect (OSTI)

    McDonald, Henry; Singh, Suminderpal

    2006-08-28T23:59:59.000Z

    The overall objective of the Chattanooga fuel cell demonstrations project was to develop and demonstrate a prototype 5-kW grid-parallel, solid oxide fuel cell (SOFC) system that co-produces hydrogen, based on Ion America’s technology. The commercial viability of the 5kW SOFC system was tested by transporting, installing and commissioning the SOFC system at the Alternative Energy Laboratory at the University of Tennessee – Chattanooga. The system also demonstrated the efficiency and the reliability of the system running on natural gas. This project successfully contributed to the achievement of DOE technology validation milestones from the Technology Validation section of the Hydrogen, Fuel Cells and Infrastructure Technologies Program Multi-Year Research, Development and Demonstration Plan. Results of the project can be found in the final technical report.

  13. Technical solutions to nonproliferation challenges

    SciTech Connect (OSTI)

    Satkowiak, Lawrence [Director, Nonproliferation, Safeguards and Security Programs, Oak Ridge National Laboratory, Oak Ridge, Tennessee (United States)

    2014-05-09T23:59:59.000Z

    The threat of nuclear terrorism is real and poses a significant challenge to both U.S. and global security. For terrorists, the challenge is not so much the actual design of an improvised nuclear device (IND) but more the acquisition of the special nuclear material (SNM), either highly enriched uranium (HEU) or plutonium, to make the fission weapon. This paper provides two examples of technical solutions that were developed in support of the nonproliferation objective of reducing the opportunity for acquisition of HEU. The first example reviews technologies used to monitor centrifuge enrichment plants to determine if there is any diversion of uranium materials or misuse of facilities to produce undeclared product. The discussion begins with a brief overview of the basics of uranium processing and enrichment. The role of the International Atomic Energy Agency (IAEA), its safeguard objectives and how the technology evolved to meet those objectives will be described. The second example focuses on technologies developed and deployed to monitor the blend down of 500 metric tons of HEU from Russia's dismantled nuclear weapons to reactor fuel or low enriched uranium (LEU) under the U.S.-Russia HEU Purchase Agreement. This reactor fuel was then purchased by U.S. fuel fabricators and provided about half the fuel for the domestic power reactors. The Department of Energy established the HEU Transparency Program to provide confidence that weapons usable HEU was being blended down and thus removed from any potential theft scenario. Two measurement technologies, an enrichment meter and a flow monitor, were combined into an automated blend down monitoring system (BDMS) and were deployed to four sites in Russia to provide 24/7 monitoring of the blend down. Data was downloaded and analyzed periodically by inspectors to provide the assurances required.

  14. 1 Copyright 1997 by ASME Creating practical design support systems is a complex design

    E-Print Network [OSTI]

    Reich, Yoram

    1 Copyright 1997 by ASME ABSTRACT Creating practical design support systems is a complex design that supports such iterations by, for example, supporting easy scripting and testing with throw­away code. Proceedings of DETC `97 1997 ASME Design Engineering Technical Conference September 14­17, 1997, Sacramento

  15. MIXING OF INCOMPATIBLE MATERIALS IN WASTE TANKS TECHNICAL BASIS DOCUMENT

    SciTech Connect (OSTI)

    SANDGREN, K.R.

    2003-10-15T23:59:59.000Z

    This document presents onsite radiological, onsite toxicological, and offsite toxicological consequences, risk binning, and control decision results for the mixing of incompatible materials in waste tanks representative accident. This technical basis document was developed to support the tank farms documented safety analysis (DSA) and describes the risk binning process, the technical basis for assigning risk bins, and the controls selected for the mixing of incompatible materials representative accident and associated represented hazardous conditions. The purpose of the risk binning process is to determine the need for safety-significant structures, systems, and components (SSC) and/or technical safety requirement (TSR)-level controls for a given representative accident or represented hazardous conditions based on an evaluation of the frequency and consequence. Note that the risk binning process is not applied to facility workers, because all facility worker hazardous conditions are considered for safety-significant SSCs and/or TSR-level controls.

  16. Technical basis document for the evaporator dump accident

    SciTech Connect (OSTI)

    GOETZ, T.G.

    2003-03-22T23:59:59.000Z

    This technical basis document was developed to support the documented safety analysis (DSA) and describes the risk binning process and the technical basis for assigning risk bins for the evaporator dump representative accident and associated represented hazardous conditions. The purpose of the risk binning process is to determine the need for safety-significant structures, systems, and components (SSC) and/or technical safety requirement (TSR)-level controls for a given representative accident or represented hazardous conditions based on an evaluation of the frequency and consequence. Note that the risk binning process is not applied to facility workers, because all facility worker hazardous conditions are considered for safety-significant SSCs and/or TSR-level controls. Determination of the need for safety-class SSCs was performed in accordance with DOE-STD-3009-94, ''Preparation Guide for US Department of Energy Nonreactor Nuclear Facility Documented Safety Analyses'', as described in this report.

  17. Mixing of incompatible materials in waste tanks technical basis document

    SciTech Connect (OSTI)

    SANDGREN, K.R.

    2003-03-21T23:59:59.000Z

    This technical basis document was developed to support the Tank Farms Documented Safety Analysis (DSA) and describes the risk binning process, the technical basis for assigning risk bins, and the controls selected for the mixing of incompatible materials representative accident and associated represented hazardous conditions. The purpose of the risk binning process is to determine the need for safety-significant structures, systems, and components (SSCs) and/or technical safety requirement (TSR)-level controls for a given representative accident or represented hazardous conditions based on an evaluation of the frequency and consequence. Note that the risk binning process is not applied to facility workers, because all facility worker hazardous conditions are considered for safety-significant SSCs and/or TSR level controls. Determination of the need for safety-class SSCs was performed in accordance with DOE-STD-3009-94, ''Preparation Guide for US Department of Energy Nonreactor Nuclear Facility Documented Safety Analyses'', as described in this report.

  18. Derived Concentration Technical Standard

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2011-05-05T23:59:59.000Z

    This standard supports the implementation of Department of Energy (DOE) Order 458.1, Radiation Protection of the Public and the Environment. It also establishes the numerical values of DCSs in a manner reflecting the current state of knowledge and practice in radiation protection

  19. SOFTWARE AND STRICT PRODUCTS LIABILITY: TECHNICAL CHALLENGES TO LEGAL NOTIONS OF RESPONSIBILITY

    E-Print Network [OSTI]

    Redmiles, David F.

    of innovative product technologies. Technological development must be supported but only to the extent such that known distinctions break down and become useless in promoting the social and technical goals that supported their creation in the law. 1. INTRODUCTION Software1 is a relatively new technological artifact

  20. Weatherization Assistance Program Technical Assistance Center

    SciTech Connect (OSTI)

    Robert Adams

    2009-01-07T23:59:59.000Z

    The following is a synopsis of the major achievements attributed to the operation of the Weatherization Assistance Program Technical Assistance Center (WAPTAC) by the National Association for State Community Services Programs (NASCSP). During the past five years, the WAPTAC has developed into the premier source for information related to operating the Weatherization Assistance Program (WAP) at the state and local levels. The services provide through WAPTAC include both virtual technical support as well as hands-on training and instruction in classroom and in the field. The WAPTAC achieved several important milestones during its operation including the establishment of a national Weatherization Day now celebrated in most states, the implementation of a comprehensive Public Information Campaign (PIC) to raise the awareness of the Program among policy makers and the public, the training of more than 150 new state managers and staff as they assume their duties in state offices around the country, and the creation and support of a major virtual information source on the Internet being accessed by thousands of staff each month. The Weatherization Assistance Program Technical Assistance Center serves the Department of Energy's (DOE) Office of Weatherization and Intergovernmental Program as a valuable training and technical assistance resource for the network of 54 direct state grantees (50 states, District of Columbia and three Native American tribes) and the network of 900 local subgrantees (comprised of community action agencies, units of local government, and other non-profit organizations). The services provided through WAPTAC focus on standardizing and improving the daily management of the WAP. Staff continually identify policies changes and best practices to help the network improve its effectiveness and enhance the benefits of the Program for the customers who receive service and the federal and private investors. The operations of WAPTAC are separated into six distinct areas: (1) Orientation for New WAP State Directors and Staff; (2) Pollution Occurrence Insurance Project; (3) Public Information Campaign; (4) State Management Training Project; (5) System for Integrating and Reviewing Technologies and Techniques; and (6) WAPTAC Services.

  1. Boiler Maximum Achievable Control Technology (MACT) Technical...

    Energy Savers [EERE]

    Boiler Maximum Achievable Control Technology (MACT) Technical Assistance - Fact Sheet, April 2015 Boiler Maximum Achievable Control Technology (MACT) Technical Assistance - Fact...

  2. Building America Residential Energy Efficiency Technical Update...

    Energy Savers [EERE]

    Residential Energy Efficiency Technical Update Meeting: August 2011 Building America Residential Energy Efficiency Technical Update Meeting: August 2011 On this page, you may link...

  3. Low Emission Development Strategies (LEDS): Technical, Institutional...

    Open Energy Info (EERE)

    Strategies (LEDS): Technical, Institutional and Policy Lessons Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Low Emission Development Strategies (LEDS): Technical,...

  4. Independent Oversight Review, Babcock & Wilcox Technical Services...

    Office of Environmental Management (EM)

    Independent Oversight Review, Babcock & Wilcox Technical Services Y-12, LLC - July 2012 Independent Oversight Review, Babcock & Wilcox Technical Services Y-12, LLC - July 2012 July...

  5. Federal Energy Management Program (FEMP) Technical Assistance...

    Energy Savers [EERE]

    Federal Energy Management Program (FEMP) Technical Assistance Request Portal User Guide Federal Energy Management Program (FEMP) Technical Assistance Request Portal User Guide...

  6. A Technical Databook for Geothermal Energy Utilization

    E-Print Network [OSTI]

    Phillips, S.L.

    1981-01-01T23:59:59.000Z

    A TECHNICAL DATABOOK FOR GEOTHERMAL ENERGY UTILIZATION S.L.Technical Databook for Geothermal Energy Utilization* s. L.Survey, Menlo Park, CA. Geothermal Energy Development, CA.

  7. Space Conditioning Standing Technical Commitee Presentation ...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Commitee Presentation Space Conditioning Standing Technical Commitee Presentation This presentation outlines the goals of the Space Conditioning Standing Technical ommittee, as...

  8. Technical Consultant Report Template | Department of Energy

    Energy Savers [EERE]

    C3d Technical Consultant Report Template.pdf More Documents & Publications External Independent Review (EIR) Report Template Technical Consultant Contract Evaluation Consultant RFP...

  9. Previous Technical Assistance | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Technical assistance provided to WGAWIEB by the Electricity Market Studies Group of LBNL and The Regulatory Assistance Project (RAP); and More limited technical assistance...

  10. Energy Department Technical Assistance Bolsters Tribal Clean...

    Energy Savers [EERE]

    Technical Assistance Bolsters Tribal Clean Energy Deployment Energy Department Technical Assistance Bolsters Tribal Clean Energy Deployment December 2, 2011 - 3:39pm Addthis The...

  11. Ocean Thermal Extractable Energy Visualization: Final Technical...

    Office of Environmental Management (EM)

    Ocean Thermal Extractable Energy Visualization: Final Technical Report Ocean Thermal Extractable Energy Visualization: Final Technical Report Report about the Ocean Thermal...

  12. Technical Journal The Bendix Technical Journal publishes noteworthy results of

    E-Print Network [OSTI]

    Rathbun, Julie A.

    ADVISORY BOARD E. C. Johnson, Chairman R. E. Esch W. E. Kock L. J. Larsen TECHNICAL CONSULTANTS ALSEP: The Scientific Voice of the Moon L. R. Lewis Some Aspects of ALSEP Structural/Thermal Design J. L

  13. Hydropower: A Regulatory Guide to Permitting and Licensing in Idaho, Montana, Oregon, and Washington.

    SciTech Connect (OSTI)

    McCoy, Gilbert A.

    1992-12-01T23:59:59.000Z

    The design, construction and operation of a hydropower project can result in many potential impacts. These potential impacts are of concern to a host of federal, state, and local authorities. Early consultation with land and water management, fish and wildlife resource protection, and health and human safety-oriented agencies should occur to determine specific concerns and study requirements for each proposed project. This Guide to Permitting and Licensing outlines the characteristic features of attractive hydropower sites; summarizes an array of developmental constraints; illustrates potential environmental impacts and concerns; and summarizes all federal, state, and local permitting and licensing requirements.

  14. Yucca Mountain Site Characterization Project technical data catalog quarterly supplement

    SciTech Connect (OSTI)

    NONE

    1995-03-31T23:59:59.000Z

    The Department of Energy (DOE)/Nuclear Regulatory Commission (NRC) Site-Specific Procedural Agreement for Geologic Repository Site Investigation and Characterization Program requires the DOE to develop and maintain a catalog of data which will be updated and provided to the NRC at least quarterly. This catalog is to include a description of the data; the time (date), place, and method of acquisition; and where the data may be examined. The Yucca Mountain Site Characterization Project (YMP) Technical Data Catalog is published and distributed in accordance with t requirements of the Site-Specific Agreement. The YMP Technical Data Catalog is a report based on reference information contained in the YMP Automated Technical Data Tracking System (ATDT). The reference information is provided by Participants for data acquired or developed in support of the YMP. The Technical Data Catalog is updated quarterly and distributed in the month following the end of each quarter. A complete revision to the catalog is published at the end of each fiscal year. Supplements to the end-of-year edition are published each quarter. These supplements provide information related to new data items not included in previous quarterly updates and data items affected by changes to@ previously published reference information. The Technical Data Catalog, dated September 30, 1994, should be retained as the baseline document for the supplements until the end-of-year revision is published and distributed in October 1995.

  15. Yucca Mountain Site Characterization Project: Technical Data Catalog quarterly supplement

    SciTech Connect (OSTI)

    NONE

    1994-03-31T23:59:59.000Z

    The March 21, 1993, Department of Energy (DOE)/Nuclear Regulatory Commission (NRC) Site-Specific Procedural Agreement for Geologic Repository Site Investigation and Characterization Program requires the DOE to develop and maintain a catalog of data which will be updated and provided to the NRC at least quarterly. This catalog is to include a description of the data; the time (date), place, and method of acquisition; and where it may be examined. The Yucca Mountain Site Characterization Project (YMP) Technical Data Catalog is published and distributed in accordance with the requirements of the Site-Specific Agreement. The YMP Technical Data Catalog is a report based on reference information contained in the YMP Automated Technical Data Tracking System (ATDT). The reference information is provided by Participants for data acquired or developed in support of the YMP. The Technical Data Catalog is updated quarterly and published in the month following the end of each quarter. A complete revision to the Catalog is published at the end of each fiscal year. Supplements to the end-of-year edition are published each quarter. These supplements provide information related to new data items not included in previous quarterly updates and data items affected by changes to previously published reference information. The Technical Data Catalog, dated September 30, 1993, should be retained as the baseline document for the supplements until the end-of-year revision is published and distributed in October 1994.

  16. Technical Letter Report: Evaluation and Analysis of a Few International Periodic Safety Review Summary Reports

    SciTech Connect (OSTI)

    Chopra, Omesh K. [Argonne National Lab., IL (United States). Environmental Science Division; Diercks, Dwight R. [Argonne National Lab., IL (United States). Nuclear Engineering Division; Ma, David Chia-Chiun [Argonne National Lab., IL (United States). Environmental Science Division; Garud, Yogendra S. [Argonne National Lab., IL (United States). Environmental Science Division

    2013-12-17T23:59:59.000Z

    At the request of the United States (U.S.) government, the International Atomic Energy Agency (IAEA) assembled a team of 20 senior safety experts to review the regulatory framework for the safety of operating nuclear power plants in the United States. This review focused on the effectiveness of the regulatory functions implemented by the NRC and on its commitment to nuclear safety and continuous improvement. One suggestion resulting from that review was that the U.S. Nuclear Regulatory Commission (NRC) incorporate lessons learned from periodic safety reviews (PSRs) performed in other countries as an input to the NRC’s assessment processes. In the U.S., commercial nuclear power plants (NPPs) are granted an initial 40-year operating license, which may be renewed for additional 20-year periods, subject to complying with regulatory requirements. The NRC has established a framework through its inspection, and operational experience processes to ensure the safe operation of licensed nuclear facilities on an ongoing basis. In contrast, most other countries do not impose a specific time limit on the operating licenses for NPPs, they instead require that the utility operating the plant perform PSRs, typically at approximately 10-year intervals, to assure continued safe operation until the next assessment. The staff contracted with Argonne National Laboratory (Argonne) to perform a pilot review of selected translated PSR assessment reports and related documentation from foreign nuclear regulatory authorities to identify any potential new regulatory insights regarding license renewal-related topics and NPP operating experience (OpE). A total of 14 PSR assessment documents from 9 countries were reviewed. For all of the countries except France, individual reports were provided for each of the plants reviewed. In the case of France, three reports were provided that reviewed the performance assessment of thirty-four 900-MWe reactors of similar design commissioned between 1978 and 1988. All of the reports reviewed were the regulator’s assessment of the PSR findings rather than the original PSR report, and all but one were English translations from the original language. In these reviews, it was found that most of the countries base their regulatory guidance to some extent (and often to a large extent) on U.S. design codes and standards, NRC regulatory guidance, and U.S. industry guidance. In addition, many of the observed operational technical issues and OpE events reported for U.S. reactors are also cited in the PSR reports. The PSR reports also identified a number of potential technical material/component performance issues and OpE events that are not commonly reported for U.S. plants.

  17. GEM Technical Design Report

    SciTech Connect (OSTI)

    Not Available

    1993-07-31T23:59:59.000Z

    The GEM collaboration was formed in June 1991 to develop a major detector for the SSC. The primary physics objectives of GEM are those central to the motivation for the SSC, to study high p{sub T} physics - exemplified by the search for Higgs bosons - and to search for new physics beyond the standard model. The authors present in this Technical Design Report (TDR) a detector with broad capabilities for the discovery and subsequent study of electroweak symmetry breaking, the origin of mass and flavor, and other physics requiring precise measurements of gammas, electrons, and muons - hence the name, GEM. In addition, as a design goal, they have taken care to provide the robustness needed to do the physics that requires high luminosity. Finally, good coverage and hermeticity allow the detection of missing transverse energy, E{sub T}. The GEM design emphasizes clean identification and high resolution measurement of the primary physics signatures for high p{sub T} physics. The approach is to make precise energy measurements that maximize the sensitivity to rare narrow resonances, to detect the elementary interaction products (quarks, leptons, and photons), and to build in the features required to reduce backgrounds.

  18. FINAL TECHNICAL REPORT

    SciTech Connect (OSTI)

    STEFAN VASILE; ZHENG LI

    2010-06-17T23:59:59.000Z

    High-resolution tracking detectors based on Active Pixel Sensor (APS) have been valuable tools in Nuclear Physics and High-Energy Physics research, and have contributed to major discoveries. Their integration time, radiation length and readout rate is a limiting factor for the planed luminosity upgrades in nuclear and high-energy physics collider-based experiments. The goal of this program was to demonstrate and develop high-gain, high-resolution tracking detector arrays with faster readout, and shorter radiation length than APS arrays. These arrays may operate as direct charged particle detectors or as readouts of high resolution scintillating fiber arrays. During this program, we developed in CMOS large, high-resolution pixel sensor arrays with integrated readout, and reset at pixel level. Their intrinsic gain, high immunity to surface and moisture damage, will allow operating these detectors with minimal packaging/passivation requirements and will result in radiation length superior to APS. In Phase I, we designed and fabricated arrays with calorimetric output capable of sub-pixel resolution and sub-microsecond readout rate. The technical effort was dedicated to detector and readout structure development, performance verification, as well as to radiation damage and damage annealing.

  19. Hanford Waste Vitrification Plant technical manual

    SciTech Connect (OSTI)

    Larson, D.E. [ed.; Watrous, R.A.; Kruger, O.L. [and others

    1996-03-01T23:59:59.000Z

    A key element of the Hanford waste management strategy is the construction of a new facility, the Hanford Waste Vitrification Plant (HWVP), to vitrify existing and future liquid high-level waste produced by defense activities at the Hanford Site. The HWVP mission is to vitrify pretreated waste in borosilicate glass, cast the glass into stainless steel canisters, and store the canisters at the Hanford Site until they are shipped to a federal geological repository. The HWVP Technical Manual (Manual) documents the technical bases of the current HWVP process and provides a physical description of the related equipment and the plant. The immediate purpose of the document is to provide the technical bases for preparation of project baseline documents that will be used to direct the Title 1 and Title 2 design by the A/E, Fluor. The content of the Manual is organized in the following manner. Chapter 1.0 contains the background and context within which the HWVP was designed. Chapter 2.0 describes the site, plant, equipment and supporting services and provides the context for application of the process information in the Manual. Chapter 3.0 provides plant feed and product requirements, which are primary process bases for plant operation. Chapter 4.0 summarizes the technology for each plant process. Chapter 5.0 describes the engineering principles for designing major types of HWVP equipment. Chapter 6.0 describes the general safety aspects of the plant and process to assist in safe and prudent facility operation. Chapter 7.0 includes a description of the waste form qualification program and data. Chapter 8.0 indicates the current status of quality assurance requirements for the Manual. The Appendices provide data that are too extensive to be placed in the main text, such as extensive tables and sets of figures. The Manual is a revision of the 1987 version.

  20. 1994 DOE Technical Standards Program Workshop: Proceedings

    SciTech Connect (OSTI)

    Spellman, D.J.

    1994-12-31T23:59:59.000Z

    The DOE Technical Standards Program has been structured to provide guidance and assistance for the development, adoption, and use of voluntary standards within the Department. OMB Circular A-119, ``Federal Participation in the Development and Use of Voluntary Standards`` establishes the policy to be followed in working with voluntary standards bodies, and in adopting and using voluntary standards whenever feasible. The DOE Technical Standards Program is consistent with this policy and is dedicated to the task of promoting its implementation. The theme of this year`s workshop is ``Standards Initiatives in Environmental Management fostering the development and use of industry standards for safe, environmentally responsible operations.`` The objective of the workshop is to increase the participant`s awareness of the standardization activities taking place nationally and internationally and the impact of these activities on their efforts, and to facilitate the exchange of experiences, processes, and tools for implementing the program. Workshop sessions will include presentations by industry and Government notables in the environment, safety, and health arena with ample opportunity for everyone to ask questions and share experiences. There will be a breakout session which will concentrate on resolution of issues arising from the implementation of the DOE Technical Standards Program and a plenary session to discuss the plans developed by the breakout groups. Many organizations provide services and products which support the development, processing, distribution, and retrieval of standards. Those organizations listed at the end of the agenda will have exhibits available for your perusal throughout the workshop. Last year`s workshop was very successful in stimulating an understanding of an interest in the standards program. This year, we hope to build on that success and provide an environment for the synergism of ideas to enhance the program and advance its implementation.

  1. Istanbul Technical University Istanbul, Turkey

    E-Print Network [OSTI]

    Duchowski, Andrew T.

    and ocean engineering Faculty of science and letters Faculty of management Faculty of Aeronautics Engineering Shipbuilding and Ocean Engineering Mathematics Engineering Physics Engineering Chemistry distinguished in Turkey with its engineering and architecture education. Istanbul Technical University

  2. Offshoring and Directed Technical Change

    E-Print Network [OSTI]

    Acemoglu, Daron

    2012-11-24T23:59:59.000Z

    To study the short-run and long-run implications on wage inequality, we introduce directed technical change into a Ricardian model of offshoring. A unique final good is produced by combining a skilled and an unskilled ...

  3. Technical challenges for dismantlement verification

    SciTech Connect (OSTI)

    Olinger, C.T.; Stanbro, W.D.; Johnston, R.G.; Nakhleh, C.W.; Dreicer, J.S.

    1997-11-01T23:59:59.000Z

    In preparation for future nuclear arms reduction treaties, including any potential successor treaties to START I and II, the authors have been examining possible methods for bilateral warhead dismantlement verification. Warhead dismantlement verification raises significant challenges in the political, legal, and technical arenas. This discussion will focus on the technical issues raised by warhead arms controls. Technical complications arise from several sources. These will be discussed under the headings of warhead authentication, chain-of-custody, dismantlement verification, non-nuclear component tracking, component monitoring, and irreversibility. The authors will discuss possible technical options to address these challenges as applied to a generic dismantlement and disposition process, in the process identifying limitations and vulnerabilities. They expect that these considerations will play a large role in any future arms reduction effort and, therefore, should be addressed in a timely fashion.

  4. Guam Initial Technical Assessment Report

    SciTech Connect (OSTI)

    Baring-Gould, I.; Conrad, M.; Haase, S.; Hotchkiss, E.; McNutt, P.

    2011-04-01T23:59:59.000Z

    Under an interagency agreement, funded by the Department of Interior's (DOI) Office of Insular Affairs (OIA), the National Renewable Energy Laboratory (NREL) was tasked to deliver technical assistance to the island of Guam by conducting an island initial technical assessment that would lay out energy consumption and production data and establish a baseline. This assessment will be used to conduct future analysis and studies by NREL that will estimate energy efficiency and renewable energy potential for the island of Guam.

  5. TECHNICAL BASIS FOR THE NUCLEAR CRITICALITY REPRESENTATIVE ACCIDENT & ASSOCIATED REPRESENTED HAZARDOUS CONDITIONS

    SciTech Connect (OSTI)

    GOETZ, T.G.

    2003-06-17T23:59:59.000Z

    This document was developed to support the documented safety analysis (DSA) and describes the process and basis for assigning risk bins for the nuclear criticality representative accident and associated hazardous conditions. Revision 1 incorporates ORP IRT comments to enhance the technical presentation and also makes editorial changes. This technical basis document was developed to support the documented safety analysis (DSA), and describes the risk binning process and the technical basis for assigning risk bins for the nuclear criticality representative accident and associated hazardous conditions. The purpose of the risk binning process is to determine the need for safety-significant structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls for a given representative accident or represented hazardous condition based on an evaluation of the frequency and consequence.

  6. Cassini RTG Program. Monthly technical progress report, October 30--November 26, 1995

    SciTech Connect (OSTI)

    NONE

    1995-12-24T23:59:59.000Z

    The technical progress achieved during the period 30 October through 26 November, 1995 is described herein. This report is organized by program task structure: (1) spacecraft integration and liaison; (2) engineering support; (3) safety; (4) qualified unicouple production; (5) ETG fabrication, assembly, and test; (6) ground support equipment (GSE); (7) RTG shipping and launch support; (8) designs, reviews, and mission applications; (9) project management, quality assurance, reliability, contract changes, CAGO acquisition (operating funds), and GACO maintenance and repair; and CAGO acquisition (capital funds).

  7. The Office of Industrial Technologies technical reports

    SciTech Connect (OSTI)

    Not Available

    1992-01-01T23:59:59.000Z

    The US Department of Energy's Office of Industrial Technologies (OIT) conducts R D activities which focus on the objectives of improving energy efficiency and providing for fuel flexibility within US industry in the area of industrial energy conservation. The Office also conducts programs to reduce waste generation, increase recycling efforts, and improve the use of wastes as process feedstocks. An active program of technology transfer and education supports these activities and encourages adoption of new technologies. To accomplish these objectives OIT cooperates with the private sector to identify its technological needs and to share R D efforts. R D is conducted to the point that a new technology is shown to work and that it can be transferred to the private sector end-users. This bibliography contains information on all scientific and technical reports sponsored by the DOE Industrial Energy Conservation Program during the years 1988--1990.

  8. Technical guidance for siting criteria development

    SciTech Connect (OSTI)

    Aldrich, D.C.; Sprung, J.L.; Alpert, D.J.; Diegert, K.; Ostmeyer, R.M.; Ritchie, L.T.; Strip, D.R.; Johnson, J.D.; Hansen, K.; Robinson, J.

    1982-12-01T23:59:59.000Z

    Technical guidance to support the formulation and comparison of possible siting criteria for nuclear power plants has been developed in four areas: (1) consequences of hypothetical severe nuclear-power-plant accidents, (2) characteristics of population distributions about current reactor sites, (3) site availability within the continental United States, and (4) socioeconomic impacts of reactor siting. The impact on consequences of source-term magnitude, meteorology, population distribution, and emergency response have been analyzed. Population distributions about current sites were analyzed to identify statistical characteristics, time trends, and regional differences. A site-availability data bank was constructed for the continential United States. The data bank contains information about population densities, seismicity, topography, water availability, and land-use restrictions. Finally, the socioeconomic impacts of rural-industrialization projects, energy boomtowns, and nuclear power plants were examined to determine their nature, magnitude, and dependence on site demography and remoteness.

  9. Notwithstanding our concerns for reliability, the Energy Commission supports efforts to reduce the impacts of once-through cooling on marine and estuarine

    E-Print Network [OSTI]

    cooling towers and half of the projects under licensing review at the Energy Commission are using recycled#12;2 Notwithstanding our concerns for reliability, the Energy Commission supports efforts for improving environmental quality in the aquatic ecosystems along our coastline. In our 2005 Integrated Energy

  10. Final Technical Report

    SciTech Connect (OSTI)

    Jack Brenizer

    2011-05-16T23:59:59.000Z

    The Consortium of Big-10 University Research and Training Reactors was by design a strategic partnership of seven leading institutions. We received the support of both our industry and DOE laboratory partners. Investiments in reactor, laboratory and program infrastructure, allowed us to lead the national effort to expand and improve the education of engineers in nuclear science and engineering, to provide outreach and education to pre-college educators and students and to become a key resource of ideas and trained personnel for our U.S. industrial and DOE laboratory collaborators.

  11. CTBT technical issues handbook

    SciTech Connect (OSTI)

    Zucca, J.J. [ed.

    1994-05-01T23:59:59.000Z

    The purpose of this handbook is to give the nonspecialist in nuclear explosion physics and nuclear test monitoring an introduction to the topic as it pertains to a Comprehensive Test Ban Treaty (CTBT). The authors have tried to make the handbook visually oriented, with figures paired to short discussions. As such, the handbook may be read straight through or in sections. The handbook covers four main areas and ends with a glossary, which includes both scientific terms and acronyms likely to be encountered during CTBT negotiations. The following topics are covered: (1) Physics of nuclear explosion experiments. This is a description of basic nuclear physics and elementary nuclear weapon design. Also discussed are testing practices. (2) Other nuclear experiments. This section discusses experiments that produce small amounts of nuclear energy but differ from explosion experiments discussed in the first chapter. This includes the type of activities, such as laser fusion, that would continue after a CTBT is in force. (3) Monitoring tests in various environments. This section describes the different physical environments in which a test could be conducted (underground, in the atmosphere, in space, underwater, and in the laboratory); the sources of non-nuclear events (such as earthquakes and mining operations); and the opportunities for evasion. (4) On-site inspections. A CTBT is likely to include these inspections as an element of the verification provisions, in order to resolve the nature of ambiguous events. This chapter describes some technical considerations and technologies that are likely to be useful. (5) Selecting verification measures. This chapter discusses the uncertain nature of the evidence from monitoring systems and how compliance judgments could be made, taking the uncertainties into account. It also discusses how to allocate monitoring resources, given the likelihood of testing by various countries in various environments.

  12. Final Technical Report

    SciTech Connect (OSTI)

    Joel Walls, Richard Uden, Scott Singleton, Rone Shu, Gary Mavko

    2005-04-12T23:59:59.000Z

    Using current methods, oil and gas in the subsurface cannot be reliably predicted from seismic data. This causes domestic oil and gas fields to go undiscovered and unexploited, thereby increasing the need to import energy. The general objective of this study was to demonstrate a simple and effective methodology for estimating reservoir properties (gas saturation in particular, but also including lithology, net to gross ratios, and porosity) from seismic attenuation and other attributes using P and S-waves. Phase I specific technical objectives: • Develop Empirical or Theoretical Rock Physics Relations for Qp and Qs • Create P-wave and S-wave Synthetic Seismic Modeling Algorithms with Q • Compute P-wave and S-wave Q Attributes from Multi-component Seismic Data All objectives defined in the Phase I proposal were accomplished. During the course of this project, a new class of seismic analysis was developed based on compressional and shear wave inelastic rock properties (attenuation). This method provides a better link between seismic data and the presence of hydrocarbons. The technique employs both P and S-wave data to better discriminate between attenuation due to hydrocarbons versus energy loss due to other factors such as scattering and geometric spreading. It was demonstrated that P and S attenuation can be computed from well log data and used to generate synthetic seismograms. Rock physics models for P and S attenuation were tested on a well from the Gulf of Mexico. The P and S-wave Q attributes were computed on multi-component 2D seismic data intersecting this well. These methods generated reasonable results, and most importantly, the Q attributes indicated gas saturation.

  13. Final Technical Report

    SciTech Connect (OSTI)

    Juan Camilo Serrano

    2011-12-16T23:59:59.000Z

    New and novel material and process technologies applied in wind blade designs and production are critical to increasing the competitiveness of wind power generation against traditional sources of energy. In this project, through collaboration between PPG Industries and MAG Industrial Automation Systems, the potential of using automated manufacturing for the production of fiber glass composite wind blades was evaluated from both technical and economic points of view. Further, it was demonstrated that by modifying the standard blade raw material forms through the use of cost effective pre-impregnated rovings coupled with using an automated fiber placement machine to lay up the parts, it is possible to produce state of the art composite laminates with significantly improved mechanical performance and with higher processing rates than standard blade production technology allows for today, thereby lowering the cost of energy over turbine blades made using traditional processes and materials. In conformity with the scope of work of the submitted proposal, the project team completed each task and documented and reported its findings on the appropriate quarterly report submitted to the DOE project team. The activities and this report are divided into 5 subtasks: (1) Material Investigation - Reviews traditional materials and key specifications and testing methods; (2) Manufacturing and Automation - Identifies new candidate material forms and automated layup processes; (3) Process Development - Performs trials of candidate materials and processes; (4) Predictive Analysis - Assesses impact of new material forms and automated processes on a model blade design; and (5) Feasibility Assessment - Compares traditional manufacturing processes and materials to new candidate material forms and automated processes.

  14. Nuclear Data Capabilities Supported by the DOE NCSP

    E-Print Network [OSTI]

    Danon, Yaron

    Nuclear Data Capabilities Supported by the DOE NCSP Symposium on Nuclear Data for Criticality responsible for developing, implementing, and maintaining nuclear criticality safety. 3 #12;NCSP Technical the Production Codes and Methods for Criticality Safety Engineers (e.g. MCNP, SCALE, & COG) · Nuclear Data

  15. Proceedings of the technical review on advances in geothermal reservoir technology---Research in progress

    SciTech Connect (OSTI)

    Lippmann, M.J. (ed.)

    1988-09-01T23:59:59.000Z

    This proceedings contains 20 technical papers and abstracts describing most of the research activities funded by the Department of Energy (DOE's) Geothermal Reservoir Technology Program, which is under the management of Marshall Reed. The meeting was organized in response to several requests made by geothermal industry representatives who wanted to learn more about technical details of the projects supported by the DOE program. Also, this gives them an opportunity to personally discuss research topics with colleagues in the national laboratories and universities.

  16. POLICY STATEMENT University of Georgia Research Foundation, Inc. Policy on Equity Acquisition in Licensing

    E-Print Network [OSTI]

    Arnold, Jonathan

    POLICY STATEMENT University of Georgia Research Foundation, Inc. Policy on Equity Acquisition the interests of the company over their responsibilities to UGARF and the University of Georgia. This Policy with this Policy. II. Policy In the course of intellectual property licensing, UGARF, through the work of TCO, may

  17. ECONOMIC MODELING OF RE-LICENSING AND DECOMMISSIONING OPTIONS FOR THE

    E-Print Network [OSTI]

    ECONOMIC MODELING OF RE-LICENSING AND DECOMMISSIONING OPTIONS FOR THE KLAMATH BASIN HYDROELECTRIC to remove the dams and buy replacement power than the earlier analysis had indicated. The Klamath Project, and steelhead trout on the West Coast of the United States. PacifiCorp's 169-megawatt Klamath Hydroelectric

  18. Licensed fuel facility status report: Inventory difference data, July 1, 1994--June 30, 1995. Volume 15

    SciTech Connect (OSTI)

    Joy, D.R.

    1996-05-01T23:59:59.000Z

    The Nuclear Regulatory Commission (NRC) is committed to the periodic publication of licensed fuel facility inventory difference data, following agency review of the information and completion of any related NRC investigations. Information in this report includes inventory difference data for active fuel fabrication facilities possessing more than one effective kilogram of special nuclear material.

  19. Licensed fuel facility. Volume 14. Inventory difference data, status report, July 1, 1993--June 30, 1994

    SciTech Connect (OSTI)

    Joy, D R

    1995-03-01T23:59:59.000Z

    The Nuclear Regulatory Commission is committed to an annual publication of licensed fuel facilities` inventory difference (ID) results, after Agency review of the information and completion of any related investigations. Information in this report includes ID results for active fuel fabrication and/or recovery facilities.

  20. Licensed fuel facility status report. Inventory difference data, July 1, 1991--June 30, 1992: Volume 12

    SciTech Connect (OSTI)

    Joy, D.; Brown, C.

    1993-04-01T23:59:59.000Z

    NRC is committed to the periodic publication of licensed fuel facilities inventory difference data, following agency review of the information and completion of any related NRC investigations. Information in this report includes inventory difference data for active fuel fabrication facilities possessing more than one effective kilogram of high enriched uranium, low enriched uranium, plutonium, or uranium-233.

  1. Licensed fuel facility status report: Inventory difference data, July 1, 1990--June 30, 1991. Volume 11

    SciTech Connect (OSTI)

    Not Available

    1992-03-01T23:59:59.000Z

    NRC is committed to the periodic publication of licensed fuel facilities inventory difference data, following agency review of the information and completion of any related NRC investigations. Information in this report includes inventory difference data for active fuel fabrication facilities possessing more than one effective kilogram of high enriched uranium, low enriched uranium, plutonium, or uranium-233.

  2. Application for Replacement of Certificates, Permits, or Licenses Page 1 of 4

    E-Print Network [OSTI]

    Application for Replacement of Certificates, Permits, or Licenses Page 1 of 4 Revised: 12/10/2012 OMB Control No. 0648-0272 Expiration Date: 11/30/2015 APPLICATION FOR REPLACEMENT OF CERTIFICATES ­ REPLACEMENT REQUEST (Check Only the Items That Apply) PART I ­ BSAI Crab Permits and Scallop Permits [ ] Crab

  3. Agricultural and Related Pest Control Applicator License Classifications under the Florida Department of

    E-Print Network [OSTI]

    Watson, Craig A.

    PI-59 Agricultural and Related Pest Control Applicator License Classifications under the Florida Department of Agriculture and Consumer Services (FDACS)1 Frederick M. Fishel2 1. This document is PI-59, one Gainesville, FL 32611. The Institute of Food and Agricultural Sciences (IFAS) is an Equal Opportunity

  4. Utah Department of Health Bureau of Health Facility Licensing, Certification and Resident Assessment

    E-Print Network [OSTI]

    Tipple, Brett

    Utah Department of Health Bureau of Health Facility Licensing, Certification and Resident of Utah Rule R432-31 (http://health.utah.gov/hflcra/forms.php) This is a physician order sheet based be effectively managed at current setting. ___ Limited additional interventions: Includes care above. May also

  5. Job Title Licensed Professional Counselor Foster Care & Adoption Home-Based Services

    E-Print Network [OSTI]

    Azevedo, Ricardo

    compassionately provides quality, continuity, and a continuum of care approach to treatment. These integrated providers firmly believe that mental health and substance abuse treatment is most effective and outcomeJob Title Licensed Professional Counselor Foster Care & Adoption Home-Based Services Employer

  6. Job Title Licensed Clinical Psychologist Employer/ Agency SELIM Behavioral Health Network, Inc

    E-Print Network [OSTI]

    Azevedo, Ricardo

    , and a continuum of care approach to treatment. These integrated relationships bring innovative ways to serve health and substance abuse treatment is most effective and outcome achieved when it is delivered from and substance abuse service provider. Our network consist of expert clinical providers, Licensed Professional

  7. Student Organization Licensing Agreement WHEREAS, the Board of Regents of the University of Oklahoma ("University") owns

    E-Print Network [OSTI]

    Oklahoma, University of

    of Oklahoma ("University") owns certain marks, logos and other intellectual property related to the University; and WHEREAS, the Student Organization wishes to use the mark "Sooner", "Sooners" or "Oklahoma" in its, nontransferable license to use "Sooner", "Sooners" or "Oklahoma" to promote or identify itself. 2. The Student

  8. Technology Available for Licensing Intellectual Property Office -The Pennsylvania State University

    E-Print Network [OSTI]

    Lee, Dongwon

    CO2 without the need for high temperature, high energy-consuming processes. Along with its uniqueTechnology Available for Licensing Intellectual Property Office - The Pennsylvania State University showing inter-chain hydrogen bonding. Background Improving the mechanical properties of paper and reducing

  9. Occupational radiation Exposure at Agreement State-Licensed Materials Facilities, 1997-2010

    SciTech Connect (OSTI)

    U.S. Nuclear Regulatory Commission, Office of Nuclear Regulatory Research

    2012-07-07T23:59:59.000Z

    The purpose of this report is to examine occupational radiation exposures received under Agreement State licensees. As such, this report reflects the occupational radiation exposure data contained in the Radiation Exposure Information and Reporting System (REIRS) database, for 1997 through 2010, from Agreement State-licensed materials facilities.

  10. The illegal practice and resulting risks versus the controlled use of licensed drugs

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    The illegal practice and resulting risks versus the controlled use of licensed drugs: views coupled to mass spectrometry. anabolic I illegal practice / cattle / residue Résumé ― Usage illégal until 1988 and have been used to some extent in growing animals such as veal calves. Many illegal

  11. Reactor vessel support system

    DOE Patents [OSTI]

    Golden, Martin P. (Trafford, PA); Holley, John C. (McKeesport, PA)

    1982-01-01T23:59:59.000Z

    A reactor vessel support system includes a support ring at the reactor top supported through a box ring on a ledge of the reactor containment. The box ring includes an annular space in the center of its cross-section to reduce heat flow and is keyed to the support ledge to transmit seismic forces from the reactor vessel to the containment structure. A coolant channel is provided at the outside circumference of the support ring to supply coolant gas through the keyways to channels between the reactor vessel and support ledge into the containment space.

  12. 2011 PERFORMANCE ASSESSMENT COMMUNITY OF PRACTICE TECHNICAL EXCHANGE - SUMMARY

    SciTech Connect (OSTI)

    Seitz, R.

    2011-12-30T23:59:59.000Z

    The Performance Assessment Community of Practice (PA CoP) was developed in 2008 to improve consistency and quality in the preparation of performance assessments (PAs) and risk assessments across the Department of Energy (DOE) Complex. The term, PA, is used to represent all of these modeling applications in this report. The PA CoP goals are to foster the exchange of information among PA practitioners and to share lessons learned from PAs conducted for DOE, commercial disposal facilities, and international entities. Technical exchanges and workshops are a cornerstone of PA CoP activities. Previous technical exchanges have addressed Engineered Barriers (2009 - http://www.cresp.org/education/workshops/pacop/), the Advanced Simulation Capability for Environmental Management and the Cementitious Barriers Partnership (2010 - http://srnl.doe.gov/copexchange/links.htm). Each technical exchange also includes summary presentations regarding activities at DOE, the Nuclear Regulatory Commission (NRC) and other organizations (e.g., International Atomic Energy Agency (IAEA)) as well as a number of presentations from selected sites to provide insight and perspective from on-going modeling activities. Through the deployment of PA Assistance Teams, the PA CoP has also been engaged in the development of new PAs across the DOE Complex. As a way of improving consistency in the preparation of new PAs, the teams provide technical advice and share experiences, noteworthy practices, and lessons learned from previous Low-Level Waste Disposal Facility Federal Review Group (LFRG) reviews. Teams have provided support for PAs at Hanford, Idaho, Paducah and Portsmouth. The third annual PA CoP Technical Exchange was held on May 25-26, 2011 in Atlanta, GA. The PA CoP Steering Committee Meeting held its first meeting on May 24 prior to the Technical Exchange. Decision making using models and software quality assurance were the topical emphasis for the exchange. A new feature at the 2011 technical exchange was the use of panel discussions to solicit feedback from regulators and practitioners. This report summarizes discussions and recommendations from the steering committee meeting and presentations and feedback obtained at the technical exchange. Appendix I includes the steering committee meeting agenda and Appendix II includes the agenda for the technical exchange and a screenshot of the presentations and video files that are available online.

  13. Technical Report: Final

    SciTech Connect (OSTI)

    Lueking, Angela D.; Wang, Cheng-Yu

    2014-09-30T23:59:59.000Z

    The objective of this work was to develop catalyzed nanoporous materials that have superior hydrogen uptake between 300K and 400K and moderate pressures. Platinum nanoparticles were introduced to both activated carbons (ACs) and microporous metal organic frameworks (MMOFs) in order to dissociate molecular hydrogen into an active hydrogen species that diffuses from the catalyst to weakly chemisorbs to the AC/MMOF support; this combined sequence is referred to as the hydrogen spillover mechanism. For all materials studied, maximum excess hydrogen uptake was 1-1.4 wt% (excess) at 300K, falling short of DOE storage goals (5.5 wt% by 2015). Select Pt/AC materials (after in situ catalyst activation) had high uptake (up to 1.4 wt%) at low pressure which significantly exceeded that expected for physisorption. The uptake was not correlated to size of Pt catalyst, but appeared to be associated with high surface activity of the AC support and the methodology of catalyst doping. Multiple techniques were explored to introduce Pt nanoparticles into MMOFs, but most led to significant structural degradation. Ultimately, a ‘pre-bridge’ (PB) technique was used to introduce Pt/AC catalysts into MMOFs, as the PB technique led to virtually non-detectable changes in structure. At high pressure, hydrogen spillover of ~1 wt% (excess) to a PB-MMOF was very slow (i.e. >80 hours at 70-80 bar), which can be attributed to high diffusion barriers in a complex three-surface domain material (Pt, AC, MMOF) as well as unexpected evidence for mechanical instability of the undoped MMOF precursor. In a low-pressure comparison study of three PB-MMOFs, we found evidence that the doping technique may introduce defects which may contribute to enhanced adsorption at 300K. However, we could not rule out the effect of active Pt sites, as common predictors of adsorption generally favored the materials without Pt. Furthermore, spectroscopic evidence provided definitive evidence of weak hydrogen chemisorption to two MMOFs and AC, and was found only for materials containing Pt catalyst. Overall, high uptake via hydrogen spillover requires high catalytic activity and an energy neutral surface landscape for ready diffusion, with little to no correlation to the size of the Pt nanoparticle or textural properties (i.e. surface area or porosity) of the AC or MMOF support.

  14. Improving the effectiveness of impact assessment pertaining to Indigenous peoples in the Brazilian environmental licensing procedure

    SciTech Connect (OSTI)

    Hanna, Philippe [Department of Cultural Geography, Faculty of Spatial Sciences, University of Groningen, PO Box 800, 9700 AV Groningen (Netherlands); Vanclay, Frank, E-mail: frank.vanclay@rug.nl [Department of Cultural Geography, Faculty of Spatial Sciences, University of Groningen, PO Box 800, 9700 AV Groningen (Netherlands); Langdon, Esther Jean [Department of Anthropology, Center for Philosophy and Human Sciences, Federal University of Santa Catarina PO Box 5104, 88040-970, Florianópolis, SC (Brazil); Arts, Jos [Department of Planning, Faculty of Spatial Sciences, University of Groningen, PO Box 800, 9700 AV Groningen (Netherlands)

    2014-04-01T23:59:59.000Z

    The number of environmental licence applications for projects affecting Indigenous peoples in Brazil has increased since the implementation of a major infrastructure program (Programa de Aceleração do Crescimento) in 2007. This increase has caused problems for Brazilian agencies involved in environmental licensing procedures (IBAMA, FUNAI and others). We analyze the Brazilian environmental licensing procedure for situations involving Indigenous peoples, Maroons (Quilombolas) or other traditional communities in order to identify potential improvements for Brazil and potentially other countries. Although Brazilian procedures are consistent with international best practice in environmental licensing, in practice social impacts are inadequately addressed, mitigation measures are poorly implemented, and there is a lack of enforcement and compliance. The paper is based on document analysis and interviews with key actors in governmental and non-governmental organizations and Indigenous leaders. We suggest that Free, Prior and Informed Consent (FPIC) processes need to be conducted at the earliest stages of project planning, and that Indigenous peoples should actively participate in impact assessment, monitoring and evaluation processes. In order to achieve a social licence to operate, there needs to be full recognition of traditional knowledge and acceptance of Indigenous values and concepts. We also recommend increased involvement of social experts and mediators as well as improved accountability, enforcement and grievance mechanisms in the licensing process. - Highlights: • The Brazilian environmental licensing system needs to address social impacts better. • Communities need to be consulted at the earliest stage possible. • Indigenous peoples need to be invited to participate in impact assessment teams. • Independent Indigenous committees to monitor implementation of mitigation measures. • Accountability, enforcement and grievance mechanisms need to be improved.

  15. Consortium Support (Fixed Support) | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE: Alternative FuelsNovember 13, 2014 BuildingEnergyEnergyConsortium Support (Fixed Support)

  16. Nutrient Management TrainingNutrient Management Training for Technical Service Providersfor Technical Service Providers

    E-Print Network [OSTI]

    Nutrient ManagementNutrient Management ­­ Record KeepingRecord Keeping ­­ Feed ManagementFeed ManagementNutrient Management TrainingNutrient Management Training for Technical Service Providersfor Management Planning Technical Guidance.Management Planning Technical Guidance. Manure and Wastewater Handling

  17. Enabling Services Dyslexia Support

    E-Print Network [OSTI]

    Anderson, Jim

    Enabling Services Dyslexia Support information for students website: www.soton.ac.uk/edusupport/dyslexia, George Thomas Building (37), Highfield Campus #12;2 Contents About Dyslexia Support.........................................................11 National and Local Organisations: .....................................12 #12;3 About Dyslexia

  18. Supported PV module assembly

    DOE Patents [OSTI]

    Mascolo, Gianluigi; Taggart, David F.; Botkin, Jonathan D.; Edgett, Christopher S.

    2013-10-15T23:59:59.000Z

    A supported PV assembly may include a PV module comprising a PV panel and PV module supports including module supports having a support surface supporting the module, a module registration member engaging the PV module to properly position the PV module on the module support, and a mounting element. In some embodiments the PV module registration members engage only the external surfaces of the PV modules at the corners. In some embodiments the assembly includes a wind deflector with ballast secured to a least one of the PV module supports and the wind deflector. An array of the assemblies can be secured to one another at their corners to prevent horizontal separation of the adjacent corners while permitting the PV modules to flex relative to one another so to permit the array of PV modules to follow a contour of the support surface.

  19. Emergency Medical Support

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1997-08-21T23:59:59.000Z

    This volume defines coordination between emergency planners and emergency medical support. Canceled by DOE G 151.1-4.

  20. Office of Sustainability Support

    Broader source: Energy.gov [DOE]

    The Office of Sustainability Support serves as AU’s organizational lead in partnering with the Department’s Sustainability Performance Office to support the understanding and implementation of sustainability programs and requirements within the Department, including through supporting development and implementation of DOE’s annual Strategic Sustainability Program Plan.