Sample records for led light bulb

  1. GREEN LIVING Replace incandencent and halogen light bulbs with LED and CLFs

    E-Print Network [OSTI]

    Thaxton, Christopher S.

    GREEN LIVING GUIDE ENERGY TRAVEL FOOD sustain yosef WATER Replace incandencent and halogen light for your laundry RESIST THAT SWITCH! Use natural light during the day, and no lights when you are gone USE MORE THAN YOU CAN EAT, reduce your waste stream DRINK FAIR TRADE COFFEE - Check out Conrad

  2. Solar light bulb

    SciTech Connect (OSTI)

    Smith, D.A.

    1983-07-26T23:59:59.000Z

    A system for generating light directly using solar energy is provided herein. It includes a concentrator and accumulator for the sun's rays to generate a concentrated beam of visible solar radiation. A distributor shaft is provided for distributing the beam of visible solar radiation. A fork is provided in the distributor shaft to define a plurality of branch lines, each provided with a mirror at the intersection to direct the beam down the respective branch line to permit parallel fractions of the beam to be reflected off the respective mirrors and to pass down the respective branch line. A solar bulb is provided including a double walled upper bulbous portion including the inlet from the branch line and a pair of heat outlet tubes, and a double walled lower bulbous portion, the upper portion thereof being divergently reflective, with the lower portion having walls which are either transparent or translucent to provide greater light diffusion, and the space between the two walls being maintained under vacuum to provide heat insulation values. A structure is provided within the solar bulb for the absorption and radiation of the concentrated beam of visible solar radiation. Preferably structure is provided connected to the solar bulb to draw in outside air in the summer to direct it past the solar bulb and to air vent hot air produced at the solar bulb to the outside, thereby providing light with minimal heat in the summer. The same structure is operated in the winter to draw in household air to direct it past the solar bulb and to recirculate such heated air produced at the solar bulb to the house, thereby providing light and heat in the winter.

  3. Consumer Light Bulb Changes: Briefing and Resources for Media...

    Broader source: Energy.gov (indexed) [DOE]

    flux") - CFL: Compact Fluorescent Lamp: The curly fluorescent bulbs - LED: Light Emitting Diode: more recently emerging technology, also called "solid state lighting" as it is...

  4. Waste Toolkit A-Z Light bulbs

    E-Print Network [OSTI]

    Melham, Tom

    Waste Toolkit A-Z Light bulbs Can I recycle light bulbs? It depends what type of bulbs you have of in the normal University waste bins (landfill waste). Energy saving bulbs and fluorescent tubes are classified light bulbs? Standard filament bulbs Put in the waste bin (landfill waste) as these are not classified

  5. Comparing Light Bulbs

    Broader source: Energy.gov [DOE]

    In this exercise, students will use a light to demonstrate the difference between being energy-efficient and energy-wasteful, and learn what energy efficiency means.

  6. Wiring Switches to Light Bulbs

    E-Print Network [OSTI]

    Buckley, Stephen M

    2011-01-01T23:59:59.000Z

    Given n buttons and n bulbs so that the ith button toggles the ith bulb and at most two other bulbs, we compute the sharp lower bound on the number of bulbs that can be lit regardless of the action of the buttons.

  7. LED Lighting Basics

    Broader source: Energy.gov [DOE]

    Light-Emitting diodes (LEDs) efficiently produce light in a fundamentally different way than any legacy or traditional source of light.

  8. Metacapacitors for LED Lighting: Metacapacitors

    SciTech Connect (OSTI)

    None

    2010-09-02T23:59:59.000Z

    ADEPT Project: The CUNY Energy Institute is developing less expensive, more efficient, smaller, and longer-lasting power converters for energy-efficient LED lights. LEDs produce light more efficiently than incandescent lights and last significantly longer than compact fluorescent bulbs, but they require more sophisticated power converter technology, which increases their cost. LEDs need more sophisticated converters because they require a different type of power (low voltage direct current, or DC) than what's generally supplied by power outlets. The CUNY Energy Institute is developing sophisticated power converters for LEDs that contain capacitors made from new, nanoscale materials. Capacitors are electrical components that are used to store energy. CUNY's unique capacitors are configured with advanced power circuits to more efficiently control and convert power to the LED lighting source. They also eliminate the need for large magnetic components, instead relying on networks of capacitors that can be easily printed on plastic substrate. CUNY's prototype LED power converter already meets DOE's 2020 projections for the energy efficiency of LED power converters.

  9. Consumer Light Bulb Changes: Briefing and Resources for Media...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Consumer Light Bulb Changes: Briefing and Resources for Media and Retailers Consumer Light Bulb Changes: Briefing and Resources for Media and Retailers This presentation provides...

  10. LED Lighting Retrofit

    E-Print Network [OSTI]

    Shaw-Meadow, N.

    2011-01-01T23:59:59.000Z

    ? Municipal Street Lighting Consortium ? American Public Power Association (APPA) ? Demonstration in Energy Efficiency Development (DEED) ? Source of funding and database of completed LED roadway projects 6 Rules of the Road ESL-KT-11-11-57 CATEE 2011..., 2011 ? 9 Solar-Assisted LED Case Study LaQuinta Hotel, Cedar Park, Texas ? Utilizes 18 - ActiveLED Solar-Assisted Parking Lot Lights ? Utilizes ?power management? to extend battery life while handling light output ? Reduces load which reduces PV...

  11. How to upgrade your incandescent light bulbs Many people are choosing replacements for their standard incandescent light bulbs to save money or energy, because they've heard of new LED

    E-Print Network [OSTI]

    Bystroff, Chris

    or building a new home, work wi efficient light fixture, · use occupancy or vacancy sensors, or · if you are renovating your home

  12. LED lamp or bulb with remote phosphor and diffuser configuration with enhanced scattering properties

    DOE Patents [OSTI]

    Tong, Tao; Le Toquin, Ronan; Keller, Bernd; Tarsa, Eric; Youmans, Mark; Lowes, Theodore; Medendorp, Jr., Nicholas W; Van De Ven, Antony; Negley, Gerald

    2014-11-11T23:59:59.000Z

    An LED lamp or bulb is disclosed that comprises a light source, a heat sink structure and an optical cavity. The optical cavity comprises a phosphor carrier having a conversions material and arranged over an opening to the cavity. The phosphor carrier comprises a thermally conductive transparent material and is thermally coupled to the heat sink structure. An LED based light source is mounted in the optical cavity remote to the phosphor carrier with light from the light source passing through the phosphor carrier. A diffuser dome is included that is mounted over the optical cavity, with light from the optical cavity passing through the diffuser dome. The properties of the diffuser, such as geometry, scattering properties of the scattering layer, surface roughness or smoothness, and spatial distribution of the scattering layer properties may be used to control various lamp properties such as color uniformity and light intensity distribution as a function of viewing angle.

  13. 600 New Lights Bulbs to Improve Energy Efficiency at DOE | Department...

    Broader source: Energy.gov (indexed) [DOE]

    our Washington, D.C., Forrestal North Building canopy with state of the art Light Emitting Diode (LED) fixtures. Every new bulb now uses just 23 watts instead of 205 watts....

  14. 100 Prisoners and A light Bulb Yisong Song

    E-Print Network [OSTI]

    Morrow, James A.

    100 Prisoners and A light Bulb Yisong Song 1. Introduction The article represent three different protocols for solving the "100 Prisoners and a Light Bulb" riddle, including the explicit computations only a light bulb with a toggle switch. The prisoner will be able to observe the current state

  15. How Energy-Efficient Light Bulbs Compare with Traditional Incandescent...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    used light fixtures or bulbs with models that have earned the ENERGY STAR, you can save 75 each year. Compared to traditional incandescents, energy-efficient lightbulbs...

  16. LED Lighting Facts®

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(FactDepartment ofLetter Report:40PM toLED Lighting Facts LED Lighting Facts LEDLED

  17. Full Spectrum Light Therapy Full spectrum light bulbs are said to not only improve mood, but also

    E-Print Network [OSTI]

    Bates, Rebecca A.

    Full Spectrum Light Therapy Full spectrum light bulbs are said to not only improve mood, but also spectrum light bulbs produce light that is seen by the human eye in a bluish-white tint. Where is full

  18. Sandia National Laboratories: efficient LED lighting

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Partnership, Research & Capabilities, Solid-State Lighting Solid state lighting (SSL), which uses light-emitting diodes (LEDs), has the potential to be 10 times more energy...

  19. Free Energy Efficiency Kit includes CFL light bulbs,

    E-Print Network [OSTI]

    Rose, Annkatrin

    Free Energy Efficiency Kit Kit includes CFL light bulbs, spray foam, low-flow shower head, and more for discounted energy assessments. FREE HOME ENERGY EFFICIENCY SEMINAR N e w R i ver L i g ht & Pow e r a n d W! Building Science 101 Presentation BPI Certified Building Professionals will present home energy efficiency

  20. Text-Alternative Version: L Prize™: The Race for Super Efficient Light Bulbs

    Broader source: Energy.gov [DOE]

    Below is the text-alternative version of the L Prize™: The Race for Super Efficient Light Bulbs webcast.

  1. THE LIGHT BULB PROBLEM 1 Ramamohan Paturi2 Sanguthevar Rajasekaran3 John Reif3

    E-Print Network [OSTI]

    Rajasekaran, Sanguthevar

    THE LIGHT BULB PROBLEM 1 Ramamohan Paturi2 Sanguthevar Rajasekaran3 John Reif3 Univ. of California Title: The Light Bulb Problem Corresponding Author: Ramamohan Paturi Department of Computer Science Mail correlational learning problem due to L. G. Valiant, 1985 and 1988: We have a sequence of n random light bulbs

  2. THE LIGHT BULB PROBLEM 1 Ramamohan Paturi2 Sanguthevar Rajasekaran3 John Reif3

    E-Print Network [OSTI]

    Rajasekaran, Sanguthevar

    THE LIGHT BULB PROBLEM 1 Ramamohan Paturi2 Sanguthevar Rajasekaran3 John Reif3 Univ. of California, San Diego Univ. of Pennsylvania Duke University 1 #12;Running Title: The Light Bulb Problem, 1985 and 1988: We have a sequence of n random light bulbs each of which is either on or off with equal

  3. Frequently Asked Questions Information on Compact Fluorescent Light Bulbs (CFLs) and Mercury

    E-Print Network [OSTI]

    Jia, Songtao

    Frequently Asked Questions Information on Compact Fluorescent Light Bulbs (CFLs) and Mercury February 2008 Why should people use CFLs? Switching from traditional light bulbs to CFLs is an effective light bulbs, last up to 10 times longer, cost little up front, and provide a quick return on investment

  4. Labeling energy cost on light bulbs lowers implicit discount rates Jihoon Min a

    E-Print Network [OSTI]

    Michalek, Jeremy J.

    Analysis Labeling energy cost on light bulbs lowers implicit discount rates Jihoon Min a , Inês L considerably. To quantify the influence of factors that drive consumer choices for light bulbs, we conducted incandescent bulbs. About half of the total lighting service (in terms of lumens) was provided by incandes

  5. THE LIGHT BULB PROBLEM 1 Ramamohan Paturi 2 Sanguthevar Rajasekaran 3 John Reif 3

    E-Print Network [OSTI]

    Reif, John H.

    THE LIGHT BULB PROBLEM 1 Ramamohan Paturi 2 Sanguthevar Rajasekaran 3 John Reif 3 Univ. of California, San Diego Univ. of Pennsylvania Duke University 1 #12; Running Title: The Light Bulb Problem, 1985 and 1988: We have a sequence of n random light bulbs each of which is either on or o# with equal

  6. Municipal Consortium LED Street Lighting Workshop Presentations...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Controls Norma Isahakian, City of Los Angeles Bureau of Street Lighting San Jose's "Smart" LED Streetlights: Controlled Amy Olay, City of San Jose Adaptive Lighting Controls...

  7. DOE Requires Westinghouse to Cease Sales of Two Light Bulb Models...

    Broader source: Energy.gov (indexed) [DOE]

    against Westinghouse Lighting Corporation, the company must cease sales of two light bulb models - medium based CFL basic model 15GLOBE652 (Westinghouse product code 3800400)...

  8. Today LED Holiday Lights, Tomorrow the World?

    SciTech Connect (OSTI)

    Gordon, Kelly L.

    2004-12-20T23:59:59.000Z

    This article for The APEM Advantage, the quarterly newsletter of the Association of Professional Energy Managers (APEM) describes the recent increase in the popularity of light emitting diode (LED) lighting and compares LED light output with that of incandescent and compact fluorescent lighting.

  9. LED Light Sources for Projection Display Applications

    E-Print Network [OSTI]

    Palffy-Muhoray, Peter

    LED Light Sources for Projection Display Applications By Chenhui Peng 04-13-2012 #12;Outline · 1. · The first practical LED is in red color and it is made with gallium arsenide (GaAs). 4http://en.wikipedia.org/wiki/Light with holes and release energy in the form of photons. 5http://en.wikipedia.org/wiki/Light-emitting_diode #12

  10. LED Street Lighting Conversion Workshop Presentations

    Broader source: Energy.gov [DOE]

    This page provides links to the presentations given at the National League of Cities Mobile Workshop, LED Street Lighting Conversion: Saving Your Community Money, While Improving Public Safety,...

  11. Text-Alternative Version LED Lighting Forecast

    Broader source: Energy.gov [DOE]

    The DOE report Energy Savings Forecast of Solid-State Lighting in General Illumination Applications estimates the energy savings of LED white-light sources over the analysis period of 2013 to 2030....

  12. LED Lighting Off the Grid

    Energy Savers [EERE]

    D. & Kammen, D. M. Decentralized energy systems for clean electricity access. Nature Climate Change accepted, in press, (2015). Off-Grid Status Quo : Fuel Based Lighting...

  13. Financing Guidance for LED Street Lighting Programs

    Broader source: Energy.gov [DOE]

    Financing an LED street lighting replacement program can present a hurdle for many system owners, even if the planned transition offers very favorable economics. Replacing the existing system requires a significant budget, particularly as the scope of the program increases. Cities such as Los Angeles and Seattle have invested many millions of dollars into their (very successful) LED street lighting replacement programs.

  14. Pittsburgh LED Street Lighting Research Project Performance Criteria

    Broader source: Energy.gov [DOE]

    A Pittsburgh LED Street Lighting Research Project document on Technical and Aesthetic Performance for Business District LED Lighting.

  15. Demonstration Assessment of Light Emitting Diode (LED) Street...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Demonstration Assessment of Light Emitting Diode (LED) Street Lighting, Final Report Demonstration Assessment of Light Emitting Diode (LED) Street Lighting, Final Report This...

  16. Demonstration Assessment of Light-Emitting Diode (LED) Freezer...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Demonstration Assessment of Light-Emitting Diode (LED) Freezer Case Lighting Demonstration Assessment of Light-Emitting Diode (LED) Freezer Case Lighting This document is a report...

  17. LEDs for Energy Efficient Greenhouse Lighting

    E-Print Network [OSTI]

    Singh, Devesh; Meinhardt-Wollweber, Merve; Roth, Bernhard

    2014-01-01T23:59:59.000Z

    Light energy is an important factor for plant growth. In regions where the natural light source, i.e. solar radiation, is not sufficient for growth optimization, additional light sources are being used. Traditional light sources such as high pressure sodium lamps and other metal halide lamps are not very efficient and generate high radiant heat. Therefore, new sustainable solutions should be developed for energy efficient greenhouse lighting. Recent developments in the field of light source technologies have opened up new perspectives for sustainable and highly efficient light sources in the form of light-emitting diodes, i.e. LEDs, for greenhouse lighting. This review focuses on the potential of LEDs to replace traditional light sources in the greenhouse. In a comparative economic analysis of traditional vs. LED lighting, we show that the introduction of LEDs allows reduction of the production cost of vegetables in the long-run of several years, due to the high energy efficiency, low maintenance cost and lon...

  18. Why Did the LED Light Bulb Cross the Road?

    Office of Energy Efficiency and Renewable Energy (EERE)

    Could using humor as a marketing strategy make energy efficiency a bit more digestible? One Illinois grant recipient thinks it could be.

  19. Chapter 30: Quantum Physics 9. The tungsten filament in a standard light bulb can be considered a blackbody radiator.

    E-Print Network [OSTI]

    Kioussis, Nicholas

    . 1 Chapter 30: Quantum Physics 9. The tungsten filament in a standard light bulb can be considered frequency is that of infrared electromagnetic radiation, the light bulb radiates more energy in the infrared

  20. LED Lighting Facts | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(FactDepartment ofLetter Report:40PM toLED Lighting Facts LED Lighting Facts LED

  1. LED Lighting Forecast | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(FactDepartment ofLetter Report:40PM toLED Lighting Facts LED Lighting Facts

  2. LED Outdoor Area Lighting Fact Sheet

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(FactDepartment ofLetter Report:40PM toLED Lighting Facts LED LightingOutdoor Area

  3. Sustainable LED Fluorescent Light Replacement Technology

    SciTech Connect (OSTI)

    None

    2011-06-30T23:59:59.000Z

    Ilumisys and the National Center for Manufacturing Sciences (NCMS) partnered on a three-year project awarded by the United States (U.S.) Department of Energy (DOE), to quantify the impacts of LED lamps, incandescent lamps and fluorescent benchmark lamps over a product lifecycle – i.e. to develop a sustainable design and manufacturing strategy that addresses product manufacturing, use, recycling and disposal scenarios for LED-based lighting. Based on the knowledge gained from extensive product tear-down studies of fluorescent and screw-in lighting products, lifecycle assessment tools, and accelerated lifecycle testing protocols, an interactive Sustainable LED Design Guide has been developed to aid architectural and lighting designers and engineers in making design decisions that consider three important environmental impacts (greenhouse gas emissions, energy use and mercury emission) across all phases of the life of an LED lighting product. Critical information developed for the lifecycle analysis and product feature comparisons is the useful life of the lighting product as well as its performance. The Design Guide is available at www.ncms.org, and was developed based on operational and durability testing of a variety of lighting products including power consumption, light output, and useful life of a lamp in order to allow a more realistic comparison of lamp designs. This report describes the main project tasks, results and innovative features of the lifecycle assessment (LCA)-based design tools, and the key considerations driving the sustainable design of LED lighting systems. The Design Guide incorporates the following three novel features for efficiently evaluating LED lighting features in value-chains: • Bill-of-Materials (BOM) Builder – Designers may import process data for each component and supply functional data for the product, including power, consumption, lumen output and expected useful life. • Environmental Impact Review – Designs are comparable across lifecycle phases, subsystems, and environmental impact category, and can be normalized to a userdefined functional unit. • Drill-down Review – These provide an indepth look at individual lamp designs with the ability to review across subsystem or lifecycle phase.

  4. (Expired) Nationwide Limited Public Interest Waiver for LED Lighting...

    Energy Savers [EERE]

    (Expired) Nationwide Limited Public Interest Waiver for LED Lighting and HVAC Units: February 11, 2010 (Expired) Nationwide Limited Public Interest Waiver for LED Lighting and HVAC...

  5. LED Provides Effective and Efficient Parking Area Lighting at...

    Broader source: Energy.gov (indexed) [DOE]

    White Light Options for Parking Area Lighting Demonstration Assessment of Light Emitting Diode (LED) Street Lighting, Final Report Guide to FEMP-Designated Parking Lot...

  6. Westinghouse Pays $50,000 Civil Penalty to Resolve Light Bulb...

    Broader source: Energy.gov (indexed) [DOE]

    here. Addthis Related Articles DOE Requires Westinghouse to Cease Sales of Two Light Bulb Models and Allows Sale of Another Air-Con Agrees to Pay Civil Penalty to Resolve...

  7. Exam Stochastic Processes 2WB08 January 29, 2007 A light bulb burns for an amount of time having distribution F(), with Laplace trans-

    E-Print Network [OSTI]

    Giardinà, Cristian

    Exam Stochastic Processes 2WB08 ­ January 29, 2007 Problem 1: A light bulb burns for an amount moment µ2. When the light bulb burns out, it is immediately replaced by another light bulb which has the same life time distribution F(·), etc. Let m(t) be the mean number of replacements of light bulbs upto

  8. New and Underutilized Technology: High Bay LED Lighting

    Broader source: Energy.gov [DOE]

    The following information outlines key deployment considerations for high bay LED lighting within the Federal sector.

  9. Text-Alternative Version: Evaluating LED Street Lighting Solutions

    Broader source: Energy.gov [DOE]

    Below is the text-alternative version of the Evaluating LED Street Lighting Solutions webcast, held July 20, 2010.

  10. CBEA LED Site Lighting Specification - Version 1.3, Released...

    Energy Savers [EERE]

    Applications Outdoor Area Lighting Home About the Solid-State Lighting Program R&D Program Market-Based Programs SSL Basics Using LEDs Information Resources Financial Opportunities...

  11. Municipal Consortium LED Street Lighting Workshop Presentations...

    Broader source: Energy.gov (indexed) [DOE]

    A Rational View of LM-79 Reports, IES Files, and Product Variation Gary Steinberg, GE Lighting Solutions Solid-State Street Lighting: Calculating Light Loss Factors Dana Beckwith,...

  12. Municipal Consortium LED Street Lighting Workshop Presentations...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    National Association of Energy Services Companies Calculating Light Loss Factors for Solid-State Lighting Systems Chad Stalker, Philips Lumileds Lighting Intro to MSSLC's...

  13. LED Linear Lamps and Troffer Lighting

    Broader source: Energy.gov [DOE]

    The CALiPER program performed a series of investigations on linear LED lamps. Each report in the series covers the performance of up to 31 linear LED lamps, which were purchased in late 2012 or 2013. The first report focuses on bare lamp performance of LED T8 replacement lamps and subsequent reports examine performance in various troffers, as well as cost-effectiveness. There is also a concise guidance document that describes the findings of the Series 21 studies and provides practical advice to manufacturers, specifiers, and consumers (Report 21.4: Summary of Linear (T8) LED Lamp Testing , 5 pages, June 2014).

  14. Integrated LED-based luminare for general lighting

    DOE Patents [OSTI]

    Dowling, Kevin J.; Lys, Ihor A.; Roberge, Brian; Williamson, Ryan C.; Roberts, Ron; Datta, Michael; Mollnow, Tomas; Morgan, Frederick M.

    2013-03-05T23:59:59.000Z

    Lighting apparatus and methods employing LED light sources are described. The LED light sources are integrated with other components in the form of a luminaire or other general purpose lighting structure. Some of the lighting structures are formed as Parabolic Aluminum Reflector (PAR) luminaires, allowing them to be inserted into conventional sockets. The lighting structures display beneficial operating characteristics, such as efficient operation, high thermal dissipation, high output, and good color mixing.

  15. Webcast: Evaluating LED Street Lighting Solutions

    Broader source: Energy.gov [DOE]

    In this July 20, 2010 webcast, Edward Smalley of Seattle City Light provided an update on DOE Municipal Solid-State Street Lighting Consortium activities. The webcast also presented perspectives...

  16. Considering LEDs for Street and Area Lighting

    Broader source: Energy.gov [DOE]

    View Jim Brodrick's keynote video from the September 2009 IES Street and Area Lighting Conference in Philadelphia.

  17. The Hazards of Use and Disposal of Compact Fluorescent Bulbs Compact fluorescent lights (aka. CFLs) work by exciting a phosphorous coating within the tube to emit

    E-Print Network [OSTI]

    Maroncelli, Mark

    The Hazards of Use and Disposal of Compact Fluorescent Bulbs Compact fluorescent lights (aka. CFLs the bulb to be an efficient light source. By comparison, older home thermometers contain 500 milligrams decade. HOW SHOULD I DISPOSE OF CFL'S? The presence of mercury requires that all CFL bulbs are properly

  18. Measured Off-Grid LED Lighting System Performance

    E-Print Network [OSTI]

    Granderson, Jessica

    2009-01-01T23:59:59.000Z

    Budget: The Economics of Off-Grid Lighting for SmallA. Jacobson. 2007. "The Off-Grid Lighting Market in WesternTesting for Emerging Off-grid White-LED Illumination Systems

  19. Demonstrating LED and Fiber Optic Lighting in Commissary Applications

    Broader source: Energy.gov [DOE]

    Presentation—given at the Federal Utility Partnership Working Group (FUPWG) Fall 2008 meeting—covers goals of the project and applications for light-emitting diodes (LEDs) and fiber optic lighting.

  20. LED Lighting Facts | Department of Energy

    Energy Savers [EERE]

    results according to industry standards. For lighting buyers, designers, and energy efficiency programs, the program provides information essential to evaluating SSL products....

  1. L Prize™: The Race for Super Efficient Light Bulbs

    Broader source: Energy.gov [DOE]

    This September 23, 2008 webcast provided an overview of the Bright Tomorrow Lighting Prize (L Prize) technology competition. The L Prize calls for super-efficient SSL products to replace two of the...

  2. Lighting the Great Outdoors: LEDs in Exterior Applications

    SciTech Connect (OSTI)

    Cook, Tyson D. S.; Bryan, Mary M.; Kinzey, Bruce R.; Myer, Michael

    2008-08-17T23:59:59.000Z

    Recent progress in the development of white light LEDs promises great impact by opening up the huge potential for LED illumination in new areas. One such area is general illumination for exterior applications. For example, there are an estimated combined 60.5 million roadway and parking installations in the U.S. These lights account for an estimated 53.3 TWh of electricity usage annually -- nearly 7% of all lighting. If LEDs could provide the same light performance with just 25% greater efficiency, savings of over 13 TWh could be achieved. In 2007, the authors assessed emerging LED lighting technologies in a parking garage and on a city street. The purpose of these tests was to enable a utility to determine whether energy efficiency programs promoting white light LED products might be justified. The results have supported the great promise of LEDs in exterior applications, while also highlighting the barriers that continue to hinder their widespread adoption. Such barriers include 1) inconsistent product quality across manufacturers; 2) lack of key metrics for comparing LEDs to conventional sources; and 3) high upfront cost of LED luminaires compared to conventional luminaires. This paper examines these barriers, ways in which energy-efficiency programs could help to overcome them, and the potential for energy and financial savings from LED lighting in these two exterior applications.

  3. Keeping Pace with LED Lighting Trends

    Office of Energy Efficiency and Renewable Energy (EERE)

    This year’s Solid State Lighting Market Introduction Workshop, to be held November 13-14 in Portland, Oregon, will include expert guidance from industry leaders and the Energy Department's national laboratories.

  4. Testimonials - Partnerships in LED Lighting - Philips Lumileds...

    Broader source: Energy.gov (indexed) [DOE]

    lighting systems, followed by a computer screen with data, followed by a man wearing a blue lab coat and face mask is entering data in a computer in a laboratory. DOE has helped...

  5. EECBG Success Story: Solar LED Light Pilot Project Illuminates...

    Energy Savers [EERE]

    courtesy of Lionel Green, Sand Mountain Reporter. A strip of new solar-powered light emitting-diode (LED) streetlights in Boaz, Alabama were installed with grant funds from the...

  6. WEBINAR: LED LIGHTING IN A PERFORMING ARTS BUILDING

    Broader source: Energy.gov [DOE]

    Can LEDs render skin tones and makeup accurately in a dressing room? Can they provide the vertical footcandles in a studio to make dancers' bodies visible, or deliver acting studio lighting to...

  7. Optimized Phosphors for Warm White LED Light Engines

    SciTech Connect (OSTI)

    Setlur, Anant; Brewster, Megan; Garcia, Florencio; Hill, M. Christine; Lyons, Robert; Murphy, James; Stecher, Tom; Stoklosa, Stan; Weaver, Stan; Happek, Uwe; Aesram, Danny; Deshpande, Anirudha

    2012-07-30T23:59:59.000Z

    The objective of this program is to develop phosphor systems and LED light engines that have steady-state LED efficacies (using LEDs with a 60% wall-plug efficiency) of 105–120 lm/W with correlated color temperatures (CCT) ~3000 K, color rendering indices (CRI) >85, <0.003 distance from the blackbody curve (dbb), and <2% loss in phosphor efficiency under high temperature, high humidity conditions. In order to reach these goals, this involves the composition and processing optimization of phosphors previously developed by GE in combination with light engine package modification.

  8. LED Lights for All Occasions | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(FactDepartment ofLetter Report:40PM toLED Lighting Facts LED Lighting FactsLED

  9. An Integrated Solid-State LED Luminaire for General Lighting

    SciTech Connect (OSTI)

    Kevin Dowling; Fritz Morgan Ihor Lys; Mike Datta; Bernd Keller; Thomas Yuan

    2009-03-31T23:59:59.000Z

    A strong systems approach to designing and building practical LED-based replacement lamps is lacking. The general method of taking high-performance LEDs and marrying them to standard printed circuit boards, drivers and a heat sink has fallen short of the promise of LED lighting. In this program, a top-down assessment of requirements and a bottom-up reinvention of LED sources, electronics, optics and mechanics have resulted in the highest performance lamp possible. The team, comprised of Color Kinetics, the leaders in LED lighting and Cree, the leaders in LED devices took an approach to reinvent the package, the driver and the overall form and aesthetic of a replacement source. The challenge was to create a new benchmark in LED lighting - the resultant lamp, a PAR38 equivalent, met the light output, color, color quality and efficacy marks set out in the program as well as being dimmable, which is important for market acceptance. The approach combined the use of multiple source die, a chip-on-board approach, a very efficient driver topology, the use of both direct emission and phosphor conversion, and a unique faceted optic to avoid the losses, artifacts and hotspots of lensed approaches. The integral heat sink provided a mechanical base and airflow using a chimney-effect for use in a wide variety of locations and orientations. These research results led to a much better understanding of the system effects of component level technologies. It was clear that best-of-breed sub-system results do not necessarily result in the best end result for the complete system. In doing this work, we did not neglect the practical aspects of these systems. These were not rarified results and commercially impractical but lent themselves to eventual commercial products in the marketplace. The end result - a high performance replacement lamp - will save significant energy while providing a high-quality light source.

  10. Department of Mechanical Engineering Spring 2013 Lumax Lighting 2: LED Industrial High Bay Light Fixture

    E-Print Network [OSTI]

    Demirel, Melik C.

    PENNSTATE Department of Mechanical Engineering Spring 2013 Lumax Lighting 2: LED Industrial High Bay Light Fixture Overview The problem that our sponsor, Rich Taylor, presented to the team was to design a light fixture for an industrial setting using high power LED lights. The challenge

  11. LED Retrofit Project in TSH Basement On July 14 2014, McMaster Facilities Services completed an energy conservation lighting

    E-Print Network [OSTI]

    Haykin, Simon

    replaced with the new LED (light emitting diode) tubes. LEDs have better lighting quality, lower energy

  12. Demonstration Assessment of Light Emitting Diode (LED) Residential Downlights and Undercabinet Lights in the Lane County Tour of Homes, Eugene, Oregon

    SciTech Connect (OSTI)

    Ton, My K.; Richman, Eric E.; Gilbride, Theresa L.

    2008-11-10T23:59:59.000Z

    In August 2008 the Pacific Northwest National Laboratory (PNNL) conducted a light emitting diode (LED) residential lighting demonstration project for the U.S. Department of Energy (DOE), Office of Building Technologies, as part of DOE’s Solid State Lighting (SSL) Technology Demonstration Gateway Program. Two lighting technologies, an LED replacement for downlight lamps (bulbs) and an LED undercabinet lighting fixture, were tested in the demonstration which was conducted in two homes built for the 2008 Tour of Homes in Eugene, Oregon. The homes were built by the Lane County Home Builders Association (HBA), and Future B Homes. The Energy Trust of Oregon (ETO) also participated in the demonstration project. The LED downlight product, the LR6, made by Cree LED Lighting Solutions acts as a screw-in replacement for incandescent and halogen bulbs in recessed can downlights. The second product tested is Phillips/Color Kinetics’ eW® Profile Powercore undercabinet fixture designed to mount under kitchen cabinets to illuminate the countertop and backsplash surfaces. Quantitative and qualitative measurements of light performance and electrical power usage were taken at each site before and after initially installed halogen and incandescent lamps were replaced with the LED products. Energy savings and simple paybacks were also calculated and builders who toured the homes were surveyed for their responses to the LED products. The LED downlight product drew 12 Watts of power, cutting energy use by 82% compared to the 65W incandescent lamp and by 84% compared to the 75W halogen lamp. The LED undercabinet fixture drew 10 watts, cutting energy use by 83% to 90% compared to the halogen product, which was tested at two power settings: a low power 60W setting and a high power 105W setting. The LED downlight consistently provided more light than the halogen and incandescent lamps in horizontal measurements at counter height and floor level. It also outperformed in vertical illuminance measurements taken on the walls, indicating better lateral dispersion of the light. The undercabinet fixture’s light output was midway between the low and high power halogen undercabinet fixture light outputs (35.8 foot candle versus 13.4 fc and 53.4 fc) but it produced a more uniform light (max/min ratio of 7.0 versus 10.8). The color correlated temperature (CCT, the blue or yellowness) of the LED light correlated well with the halogen and incandescent lights (2675 K vs 2700 K). The color rendering of the LED downlight also correlated well at 92 CRI compared to 100 CRI for the halogen and incandescent lamps. The LED undercabinet fixture had measures of 2880 K CCT and 71 CRI compared to the 2700 K and 100 CRI scores for the halogen undercabinet fixture. Builders who toured the homes were surveyed; they gave the LED downlight high marks for brightness, said the undercabinet improved shadows and glare and said both products improved overall visibility, home appearance, and home value. Paybacks on the LED downlight ranged from 7.6 years (assuming electricity cost of 11 c/kWh) to 13.5 years (at 5C/kWh). Paybacks on the LED undercabinet fixture in a new home ranged from 4.4 years (11c/kWh electricity) to 7.6 years (5c/kWh) based on product costs of $95 per LED downlight and $140 per LED undercabinet fixture at 3 hrs per day of usage for the downlight and 2 hrs per day for the undercabinet lighting.

  13. Proposal -Interactive City Lighting LED based lighting systems have enabled radically new

    E-Print Network [OSTI]

    Proposal - Interactive City Lighting Abstract LED based lighting systems have also be integrated with sensors and smart environments. This has opened up a new world. The use of the LED as a potential means for providing interactive city lighting for social

  14. Bulb mounting of solar cell

    SciTech Connect (OSTI)

    Thompson, M.E.

    1983-04-05T23:59:59.000Z

    An energy converting assembly is provided for parasiting of light from a fluorescent light bulb utilizing a solar cell. The solar cell is mounted on a base member elongated in the dimension of elongation of the fluorescent bulb, and electrical interconnections to the cell are provided. A flexible sheet of opaque material having a flat white interior reflective surface surrounds the fluorescent bulb and reflects light emitted from the bulb back toward the bulb and the solar cell. The reflective sheet is tightly held in contact with the bottom of the bulb by adhesive, a tie strap, an external clip, or the like.

  15. Mercury Lamps Recycling Fluorescent light-tubes, compact fluorescent bulbs, mercury and sodium vapor lamps, ultraviolet and

    E-Print Network [OSTI]

    Baker, Chris I.

    Mercury Lamps Recycling Fluorescent light-tubes, compact fluorescent bulbs, mercury and sodium labeled for shipment to a recycling plant for mercury, glass and aluminum recovery. The beneficial re can be recycled infinitely without losing its purity or strength. While the primary end product

  16. Have You Used LED Lighting? Tell Us About It. | Department of...

    Broader source: Energy.gov (indexed) [DOE]

    It. May 7, 2009 - 5:00am Addthis This week, John shared his experiences with light-emitting diode (LED) lighting. In a future blog, he'll share more about LED lighting. Have you...

  17. LEDs: The Future of Lighting is Here | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(FactDepartment ofLetter Report:40PM toLED Lighting Facts LEDLEDs on Semipolar

  18. #AskEnergySaver: LED Lights | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: The Future of Bad CholesteroliManage#AskEnergySaver: LED Lights #AskEnergySaver:

  19. LED Traffic Lights Get Buy American Stamp | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742Energy ChinaofSchaeferApril 1, 1999 InspectionVolunteersKarenThisDepartment ofLED traffic lights

  20. Quasars Are Not Light-Bulbs: Testing Models of Quasar Lifetimes with the Observed Eddington Ratio Distribution

    E-Print Network [OSTI]

    Hopkins, Philip F

    2008-01-01T23:59:59.000Z

    We use the observed distribution of Eddington ratios as a function of supermassive black hole (BH) mass to constrain models of AGN lifetimes and lightcurves. Given the observed AGN luminosity function, a model for AGN lifetimes (time above a given luminosity) translates directly to a predicted Eddington ratio distribution. Models for self-regulated BH growth, in which feedback produces a 'blowout' decay phase after some peak luminosity (shutting down accretion) make specific predictions for the lifetimes distinct from those expected if AGN are simply gas starved (without feedback) and very different from simple phenomenological 'light bulb' models. Present observations of the Eddington ratio distribution, spanning 5 decades in Eddington ratio, 3 in BH mass, and redshifts z=0-1, agree with the predictions of self-regulated models, and rule out 'light-bulb', pure exponential, and gas starvation models at high significance. We compare the Eddington ratio distributions at fixed BH mass and fixed luminosity (both ...

  1. LED Site Lighting in the Commercial Building Sector: Opportunities, Challenges, and the CBEA Performance Specification

    Broader source: Energy.gov [DOE]

    This March 26, 2009 webcast presented information about the Commercial Building Energy Alliances' (CBEA) efforts to explore the viability of LED site lighting in commercial parking lots. LED...

  2. TOMORROW: Department of Energy to Announce Philips Lighting North...

    Office of Environmental Management (EM)

    American consumers and businesses money. Philips developed a highly efficient light emitting diode (LED) bulb to meet rigorous requirements of the L Prize competition - ensuring...

  3. Assessing the Performance of 5mm White LED Light Sources for Developing-Country Applications

    E-Print Network [OSTI]

    Mills, Evan

    2007-01-01T23:59:59.000Z

    lamp calibrated by Labsphere Spectral measurements - LEDs inLEDs we tested is exceptionally good (as good or better than many compact fluorescent lamps),lamp. Off-grid lighting products using the poorer LEDs would

  4. New Family of Tiny Crystals Glow Bright in LED Lights | Advanced...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    crystals that glow different colors may be the missing ingredient for white light-emitting diode (LED) lighting that illuminates homes and offices as effectively as natural...

  5. Light source comprising a common substrate, a first led device and a second led device

    SciTech Connect (OSTI)

    Choong, Vi-En (Carlsbad, CA)

    2010-02-23T23:59:59.000Z

    At least one stacked organic or polymeric light emitting diode (PLEDs) devices to comprise a light source is disclosed. At least one of the PLEDs includes a patterned cathode which has regions which transmit light. The patterned cathodes enable light emission from the PLEDs to combine together. The light source may be top or bottom emitting or both.

  6. Psychophysical evaluations of modulated color rendering for energy performance of LED-based architectural lighting

    E-Print Network [OSTI]

    Thompson, Maria do Rosário

    2007-01-01T23:59:59.000Z

    This thesis is focused on the visual perception evaluation of colors within an environment of a highly automated lighting control strategy. Digitally controlled lighting systems equipped with light emitting diodes, LEDs, ...

  7. Article Published on LED Lumen Maintenance and Light Loss Factors...

    Broader source: Energy.gov (indexed) [DOE]

    of a comprehensive lifetime rating - as well as the problematic relationship between SSL lifetime and lumen maintenance - determining an appropriate LLD factor for LED products...

  8. Demonstration Assessment of Light-Emitting Diode (LED) Parking Lot Lighting in Leavenworth, KS

    SciTech Connect (OSTI)

    Myer, Michael; Kinzey, Bruce R.; Curry, Ku'uipo

    2011-05-06T23:59:59.000Z

    This report describes the process and results of a demonstration of solid-state lighting (SSL) technology in a commercial parking lot lighting application, under the U.S. Department of Energy (DOE) Solid-State Lighting Technology GATEWAY Demonstration Program. The parking lot is for customers and employees of a Walmart Supercenter in Leavenworth, Kansas and this installation represents the first use of the LED Parking Lot Performance Specification developed by the DOE’s Commercial Building Energy Alliance. The application is a parking lot covering more than a half million square feet, lighted primarily by light-emitting diodes (LEDs). Metal halide wall packs were installed along the building facade. This site is new construction, so the installed baseline(s) were hypothetical designs. It was acknowledged early on that deviating from Walmart’s typical design would reduce the illuminance on the site. Walmart primarily uses 1000W pulse-start metal halide (PMH) lamps. In order to provide a comparison between both typical design and a design using conventional luminaires providing a lower illuminance, a 400W PMH design was also considered. As mentioned already, the illuminance would be reduced by shifting from the PMH system to the LED system. The Illuminating Engineering Society of North America (IES) provides recommended minimum illuminance values for parking lots. All designs exceeded the recommended illuminance values in IES RP-20, some by a wider margin than others. Energy savings from installing the LED system compared to the different PMH systems varied. Compared to the 1000W PMH system, the LED system would save 63 percent of the energy. However, this corresponds to a 68 percent reduction in illuminance as well. In comparison to the 400W PMH system, the LED system would save 44 percent of the energy and provide similar minimum illuminance values at the time of relamping. The LED system cost more than either of the PMH systems when comparing initial costs. However, when the life-cycle costs from energy and maintenance were factored into the scenario, the LED system had lower costs at the end of a 10-year analysis period. The LED system had a 6.1 year payback compared to the 1000W PMH system and a 7.5 year payback versus the 400W PMH system. The costs reflect high initial cost for the LED luminaire, plus more luminaires and (subsequently) more poles for the LED system. The other major issue affecting cost effectiveness was that Leavenworth, Kansas has very low electricity costs. The melded rate for this site was $0.056 per kWh for electricity. However, if the national electricity rate of $0.1022/kWh was used the payback would change to between four and five years for the LED system. This demonstration met the GATEWAY requirements of saving energy, matching or improving illumination, and being cost effective. The project also demonstrated that the Commercial Building Energy Alliance (CBEA) specification works in practice. Walmart appreciated having an entire site lighted by LEDs to gain more experience with the technology. Walmart is reviewing the results of the demonstration as they consider their entire real estate portfolio.

  9. Measured Off-Grid LED Lighting System Performance

    E-Print Network [OSTI]

    Granderson, Jessica

    2009-01-01T23:59:59.000Z

    The Specter of Fuel-Based Lighting," Science 308:1263-1264.Mills. 2008. "Solid-State Lighting on a Shoestring Budget:The Economics of Off-Grid Lighting for Small Businesses in

  10. Demonstration Assessment of Light-Emitting Diode (LED) Accent Lighting at the Field Museum in Chicago, IL

    SciTech Connect (OSTI)

    Myer, Michael; Kinzey, Bruce R.

    2010-12-10T23:59:59.000Z

    This report reviews a demonstration of light-emitting diode (LED) accent lighting compared to halogen (typical) accent lighting in a gallery of the Field Museum in Chicago, IL.

  11. Quasars Are Not Light-Bulbs: Testing Models of Quasar Lifetimes with the Observed Eddington Ratio Distribution

    E-Print Network [OSTI]

    Philip F. Hopkins; Lars Hernquist

    2009-04-30T23:59:59.000Z

    We use the observed distribution of Eddington ratios as a function of supermassive black hole (BH) mass to constrain models of AGN lifetimes and lightcurves. Given the observed AGN luminosity function, a model for AGN lifetimes (time above a given luminosity) translates directly to a predicted Eddington ratio distribution. Models for self-regulated BH growth, in which feedback produces a 'blowout' decay phase after some peak luminosity (shutting down accretion) make specific predictions for the lifetimes distinct from those expected if AGN are simply gas starved (without feedback) and very different from simple phenomenological 'light bulb' models. Present observations of the Eddington ratio distribution, spanning 5 decades in Eddington ratio, 3 in BH mass, and redshifts z=0-1, agree with the predictions of self-regulated models, and rule out 'light-bulb', pure exponential, and gas starvation models at high significance. We compare the Eddington ratio distributions at fixed BH mass and fixed luminosity (both are consistent, but the latter are much less constraining). We present empirical fits to the lifetime distribution and show how the Eddington ratio distributions place tight limits on AGN lifetimes at various luminosities. We use this to constrain the shape of the typical AGN lightcurve, and provide simple analytic fits. Given independent constraints on episodic lifetimes, most local BHs must have gained their mass in no more than a couple of bright episodes, in agreement with merger-driven fueling models.

  12. LED Lighting Flicker and Potential Health Concerns: IEEE Standard PAR1789 Update

    E-Print Network [OSTI]

    Lehman, Brad

    LED Lighting Flicker and Potential Health Concerns: IEEE Standard PAR1789 Update Arnold Wilkins for mitigating health risks to viewers" has been formed to advise the lighting industry, ANSI/NEMA, IEC, EnergyStar and other standards groups about the emerging concern of flicker in LED lighting. This paper introduces

  13. Demonstration Assessment of Light-Emitting Diode (LED) Street Lighting Host Site: Lija Loop, Portland, Oregon

    SciTech Connect (OSTI)

    Kinzey, Bruce R.; Myer, Michael

    2009-11-01T23:59:59.000Z

    This report describes the process and results of a demonstration of solid-state lighting (SSL) technology in a residential street lighting application, under the U.S. Department of Energy GATEWAY Solid-State Lighting Technology Demonstration Program. In this project, eight 100W (nominal) high-pressure sodium cobra head fixtures were replaced with a like number of LED street light luminaires manufactured by Leotek, Inc. The Leotek product achieved an estimated payback in the Lija Loop installation of about 20 years for replacement scenarios and a much shorter 7.6 years for new installations. Much of the associated energy savings (55%) supporting these payback periods, however, were achieved by reducing average horizontal photopic illuminance a similar amount (53%). Examined from a different perspective, the measured performance suggests that the Leotek product is at approximate parity with the HPS cobra head in terms of average delivered photopic illumination for a given power consumption. HPS comprises the second most efficacious street lighting technology available, exceeded only by low pressure sodium (LPS). LPS technology is not considered suitable for most street lighting applications due to its monochromatic spectral output and poor color rendering ability; therefore, this LED product is performing at an efficiency level comparable to its primary competition in this application.

  14. Slutrapport for PSO 337-068 Udvikling af LED lyskilder og lamper

    E-Print Network [OSTI]

    bulb. - two LED pendants/lamps, a LED table lamp and a chair with LED lighting developed by designers Cluster lampe 13 Teknisk design af Cluster 15 Konklusion 16 Lysflyder 17 Hvordan opstod ideen om en LEDSlutrapport for PSO 337-068 Udvikling af LED lyskilder og lamper Carsten Dam-Hansen, Paul Michael

  15. Text-Alternative Version: MSSLC Member Case Studies- LED Street Lighting Programs Webinar

    Broader source: Energy.gov [DOE]

    Below is the text-alternative version of the "MSSLC Member Case Studies - LED Street Lighting Programs" webcast, held May 8, 2013.

  16. Text Alternative Version: Life-Cycle Assessment of Energy and Environmental Impacts of LED Lighting Products

    Broader source: Energy.gov [DOE]

    Below is the text-alternative version of the "Life-Cycle Assessment of Energy and Environmental Impacts of LED Lighting Products" webcast, held March 28, 2013.

  17. Scalable Light Module for Low-Cost, High Efficiency LED Luminaires...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Low-Cost, High Efficiency LED Luminaires More Documents & Publications Low-Cost Light-Emitting Diode Luminaire for General Illumination 2015 Project Portfolio 2014 Solid-State...

  18. Text-Alternative Version: CALiPER Series 21 on LED Linear Lamps and Troffer Lighting

    Broader source: Energy.gov [DOE]

    Following is a text version of a video about CALiPER Application Report Series 21 on LED Linear Lamps and Troffer Lighting.

  19. LED Linear Lamps and Troffer Lighting: CALiPER Report Series 21

    ScienceCinema (OSTI)

    Beeson, Tracy; Miller, Naomi

    2014-06-23T23:59:59.000Z

    Video about CALiPER Report Series 21 on LED Linear Lamps and Troffer Lighting, featuring interviews with Tracy Beeson and Naomi Miller of Pacific Northwest National Laboratory.

  20. Researchers Say They've Solved the Mystery of LED Lighting "Droop...

    Broader source: Energy.gov (indexed) [DOE]

    Sciences Team. Despite being cool, ultra-efficient and long lasting, the light-emitting diode (LED) faces a problem called "efficiency droop." New findings from simulations...

  1. Depth of cure and compressive strength of dental composites cured with blue light emitting diodes (LEDs)

    E-Print Network [OSTI]

    Ashworth, Stephen H.

    Depth of cure and compressive strength of dental composites cured with blue light emitting diodes with either a light emitting diode (LED) based light curing unit (LCU) or a conventional halogen LCU do reserved. Keywords: Blue light emitting diodes; Light curing unit; Composites; Irradiance; Spectrum; Depth

  2. LED Light Fixture Project FC1 Director's Conference Room: Life Cycle Cost and Break-even Analysis

    E-Print Network [OSTI]

    Johnston, Daniel

    . A light-emitting diode (LED) is a solid-state lighting source that switches on instantly, is readily

  3. Member Case Studies: LED Street Lighting Programs in Algona (IA), Asheville (NC), and Boston (MA)

    Broader source: Energy.gov [DOE]

    This May 8, 2013 webcast featured presentations from DOE Municipal Solid-State Street Lighting Consortium member cities about their experiences with LED street lighting. Presenters John Bilsten of...

  4. Shedding new light on LEDs | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    diodes, are the secret behind your iPhone screen, flatscreen TVs, Christmas lights and crosswalk signals. They can last longer and save more energy than traditional...

  5. 78.1: Ultra Compact Polarization Recycling System for White Light LED based Pico-Projection System

    E-Print Network [OSTI]

    78.1: Ultra Compact Polarization Recycling System for White Light LED based Pico-Projection System polarization recycling system, for white light LED based projectors, is proposed. White light LED is applied. In this paper, we propose an ultra compact polarization recycling system for white light LED based projection

  6. Largest-area Photonic Crystal LED Fabricated Demonstrates Uniform Light Emission

    Broader source: Energy.gov [DOE]

    Lumileds Lighting, the University of New Mexico, and Sandia National Laboratories teamed to demonstrate uniform light emission from the largest-area III-Nitride photonic crystal LED (1 x 1 mm2) ever fabricated. Most previous photonic crystal LED research has relied on small-area patterns written by slow, serial-writing electron-beam lithography.

  7. Article Published on LED Lumen Maintenance and Light Loss Factors

    Broader source: Energy.gov [DOE]

    An article has been published in LEUKOS: The Journal of the Illuminating Engineering Society of North America (IES) that may be of interest to the solid-state lighting community. Entitled "Lumen...

  8. Energy 101: Lighting Choices | Department of Energy

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    in your home to energy-saving incandescent, compact fluorescent lamp (CFL), or light emitting diode (LED) bulbs could save you about 50 per year. For more information on lighting...

  9. Chip-Scale Power Conversion for LED Lighting: Integrated Power Chip Converter for Solid-State Lighting

    SciTech Connect (OSTI)

    None

    2010-10-01T23:59:59.000Z

    ADEPT Project: Teledyne is developing cost-effective power drivers for energy-efficient LED lights that fit on a compact chip. These power drivers are important because they transmit power throughout the LED device. Traditional LED driver components waste energy and don't last as long as the LED itself. They are also large and bulky, so they must be assembled onto a circuit board separately which increases the overall manufacturing cost of the LED light. Teledyne is shrinking the size and improving the efficiency of its LED driver components by using thin layers of an iron magnetic alloy and new gallium nitride on silicon devices. Smaller, more efficient components will enable the drivers to be integrated on a single chip, reducing costs. The new semiconductors in Teledyne's drivers can also handle higher levels of power and last longer without sacrificing efficiency. Initial applications for Teledyne's LED power drivers include refrigerated grocery display cases and retail lighting.

  10. Considerations When Comparing LED and Conventional Lighting | Department of

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 1112011AT&T, Inc.'sEnergyTexas1.SpaceFluor Federal Services -Energy Using LEDs »

  11. LED Holiday Lights: Festive, Safe, and Efficient! | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(FactDepartment ofLetter Report:40PM to 2:05PMDOE-STD-1107-97LSEED:LDVFrequentlyLED

  12. LED Lighting on the National Mall | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the.pdfBreaking ofOil & Gas » MethaneJohnsonKristina Pflanz About Us KristinaLED

  13. High Efficiency LED Lamp for Solid-State Lighting

    SciTech Connect (OSTI)

    James Ibbetson

    2006-12-31T23:59:59.000Z

    This report contains a summary of technical achievements during a three-year project to demonstrate high efficiency, solid-state lamps based on gallium nitride/silicon carbide light-emitting diodes. Novel chip designs and fabrication processes are described for a new type of nitride light-emitting diode with the potential for very high efficiency. This work resulted in the demonstration of blue light-emitting diodes in the one watt class that achieved up to 495 mW of light output at 350 mA drive current, corresponding to quantum and wall plug efficiencies of 51% and 45%, respectively. When combined with a phosphor in Cree's 7090 XLamp package, these advanced blue-emitting devices resulted in white light-emitting diodes whose efficacy exceeded 85 lumens per watt. In addition, up to 1040 lumens at greater than 85 lumens per watt was achieved by combining multiple devices to make a compact white lamp module with high optical efficiency.

  14. Electrophoretic Deposition of Highly Efficient Phosphors for White Solid State Lighting using near UV-Emitting LEDs /

    E-Print Network [OSTI]

    Choi, Jae Ik

    2014-01-01T23:59:59.000Z

    application in white light emitting diode,” J. Mater. Res. ,phosphors for white light emitting diodes (LEDs)”, 220 thconverted white light emitting diodes by electrophoretic

  15. The light-emitting diode (LED) is an fairly new kind of light source found currently in

    E-Print Network [OSTI]

    The light-emitting diode (LED) is an fairly new kind of light source found currently in only a few applications, such as traffic lights and exit signs. As a relatively untested technology, luminaire this technology an ideal replacement for less efficient incandescent light sources, particularly in applications

  16. An Efficient LED System-in-Module for General Lighting Applications

    SciTech Connect (OSTI)

    None

    2008-09-14T23:59:59.000Z

    The objective of the project was to realize an LED-based lighting technology platform for general illumination, starting with LED chips, and integrating the necessary technologies to make compact, user-friendly, high-efficiency, energy-saving sources of controlled white (or variable-colored) light. The project is to build the system around the LEDs, and not to work on the LEDs themselves, in order that working products can be introduced soon after the LEDs reach suitable efficiency for mass-production of high-power light sources for general illumination. Because the light sources are intended for general illumination, color must be accurately maintained, requiring feedback control in the electronics. The project objective has been realized and screw base demonstrators, based on the technology developed in the project, have been built.

  17. Vehicle Traffic Control Signal Heads— Light Emitting Diode Circular Signal Supplement (VTCSH-LED). This replaced the so-called Interim LED Purchase Specifications,

    E-Print Network [OSTI]

    S. Behura

    Engineers ’ (ITE) specification for light-emitting diode (LED) circular traffic signals recently was updated (June 27, 2005) and published under the name

  18. Measured Off-Grid LED Lighting System Performance

    SciTech Connect (OSTI)

    Granderson, Jessica; Galvin, James; Bolotov, Dmitriy; Clear, Robert; Jacobson, Arne; Mills, Evan

    2008-12-18T23:59:59.000Z

    This report is a product of our ongoing effort to support the development of high-quality yet affordable products for off-grid lighting in the developing world that have good potential to succeed in the market. The effort includes work to develop low-cost testing procedures, to identify useful performance metrics, and to facilitate the development of industry standards and product rating protocols. We conducted laboratory testing of nine distinct product lines. In some cases we also tested multiple generations of a single product line and/or operating modes for a product. The resultsare summarized in Table 1. We found that power consumption and light output varied by nearly a factor of 12, with efficacy varying by a factor of more than six. Of particular note, overall luminous efficacy varied from 8.2 to 53.1 lumens per watt. Color quality indices variedmaterially, especially for correlated color temperature. Maximum illuminance, beamcandlepower, and luminance varied by 8x, 32x, and 61x respectively, suggesting considerable differences among products in terms of service levels and visual comfort. Glare varied by1.4x, and was above acceptable thresholds in most cases. Optical losses play a role in overall performance, varying by a factor of 3.2 and ranging as high as 24percent. These findings collectively indicate considerable potential for improved product design.

  19. Tired of changing light bulbs AND want to save money? Still using 100 year-old technology?

    E-Print Network [OSTI]

    Glashausser, Charles

    ?) ·Fine print: You will also reduce Global Warming pollution. Over its lifetime, a "100W" Compact will prevent global warming pollution equal to 100 to 150 gallons of gasoline AND reduce poisons like mercury bulb but lasts THIRTEEN times longer! The Compact bulb will save you $90 just in electricity cost over

  20. LED Linear Lamps and Troffer Lighting: CALiPER Report Series 21

    Broader source: Energy.gov [DOE]

    View the video about CALiPER Report Series 21 on LED Linear Lamps and Troffer Lighting, featuring interviews with Tracy Beeson and Naomi Miller of Pacific Northwest National Laboratory.

  1. Life-Cycle Assessment of Energy and Environmental Impacts of LED Lighting Products

    Broader source: Energy.gov [DOE]

    This March 28, 2013 webcast reviewed DOE's recently completed three-part study of the life-cycle energy and environmental impacts of LED lighting products relative to incandescent and CFL...

  2. LED Provides Effective and Efficient Parking Area Lighting at the NAVFAC Engineering Service Center

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(FactDepartment ofLetter Report:40PM toLED Lighting Facts LED LightingOutdoorLED

  3. Replacement of Lighting Fixtures with LED Energy Efficient Lights at the Parking Facility, Milwaukee, Wisconsin

    SciTech Connect (OSTI)

    David Brien

    2012-06-21T23:59:59.000Z

    The Forest County Potawatomi Community (FCPC or Tribe) owns a six-story parking facility adjacent to its Potawatomi Bingo Casino (the Casino) in Milwaukee, Wisconsin, as well as a valet parking facility under the Casino (collectively, the Parking Facility). The Parking Facility contained 205-watt metal halide-type lights that, for security reasons, operated 24 hours per day, 7 days per week. Starting on August 30, 2010, the Tribe replaced these fixtures with 1,760 state-of-the-art, energy efficient 55-Watt LED lights. This project resulted in an immediate average reduction in monthly peak demand of 238 kW over the fourth quarter of 2010. The average reduction in monthly peak demand from October 1 through December 31, 2010 translates into a forecast annual electrical energy reduction of approximately 1,995,000 kWh or 47.3% of the pre-project demand. This project was technically effective, economically feasible, and beneficial to the public not only in terms of long term energy efficiency and associated emissions reductions, but also in the short-term jobs provided for the S.E. Wisconsin region. The project was implemented, from approval by U.S. Department of Energy (DOE) to completion, in less than 6 months. The project utilized off-the-shelf proven technologies that were fabricated locally and installed by local trade contractors.

  4. LED Traffic Light as a Communications Device Grantham Pang, Thomas Kwan, Chi-Ho Chan, Hugh Liu.

    E-Print Network [OSTI]

    Pang, Grantham

    :http://www.eee.hku.hk/~gpang Abstract The visible light from an LED (light emitting diode) traffic light can be modulated and encoded on the description of an audio information system made up of high brightness, visible light emitting diodes (LEDs messages 1. Introduction Recently, high intensity light emitting diodes for traffic signals are available

  5. Crystal coat warms up LED light 16:46 01 February 2008

    E-Print Network [OSTI]

    Demir, Hilmi Volkan

    in the commercial market. Illuminating buildings accounts for about a quarter of the electricity used in the US in the home. Now researchers have used nanocrystals to create LEDs that give off a warm white light. Fine Articles 'Smart' lamp offers true mood lighting http://technology.newscientist.com/article/mg19626276

  6. Lamp bulb with integral reflector

    DOE Patents [OSTI]

    Levin, Izrail (Silver Spring, MD); Shanks, Bruce (Gaithersburg, MD); Sumner, Thomas L. (Wheaton, MD)

    2001-01-01T23:59:59.000Z

    An improved electrodeless discharge lamp bulb includes an integral ceramic reflector as a portion of the bulb envelope. The bulb envelope further includes two pieces, a reflector portion or segment is cast quartz ceramic and a light transmissive portion is a clear fused silica. In one embodiment, the cast quartz ceramic segment includes heat sink fins or stubs providing an increased outside surface area to dissipate internal heat. In another embodiment, the quartz ceramic segment includes an outside surface fused to eliminate gas permeation by polishing.

  7. Lumen Maintenance and Light Loss Factors: Consequences of Current Design Practices for LED's

    SciTech Connect (OSTI)

    Royer, Michael P.

    2013-09-17T23:59:59.000Z

    Synopsis: Light loss factors are used to help lighting systems meet quantitative design criteria throughout the life of the installation, but they also influence energy use. As the light sources currently being specified continue to evolve, it is necessary to reevaluate the methods used in calculating light loss factors, as well as carefully consider the consequences of different product performance attributes. Because of the unique operating characteristics of LEDs and lack of a comprehensive lifetime rating—as well as the problematic relationship between lifetime and lumen maintenance—determining an appropriate lamp lumen depreciation (LLD) factor for LED products is difficult. As a result, a unique solution has been advocated: when quantity of light is an important design consideration, the IES recommends using an LLD of not greater than 0.70. This method deviates from the typical practice for conventional sources of using the ratio of mean to initial lumen output, and can misrepresent actual performance, increase energy use, and inhibit comparisons between products. This paper discusses the complications related to LLD and LEDs, compares the performance of conventional and LED products, and examines alternatives to a maximum LLD of 0.70 for LEDs.

  8. LED Lamp Project Lights the Way to Flicker-Free Replacement Jade Sky Technologies and UC Davis's California Lighting Technology Center demonstrate the

    E-Print Network [OSTI]

    California at Davis, University of

    LED Lamp Project Lights the Way to Flicker-Free Replacement Jade Sky the flicker and dimming requirements set by the Voluntary California Quality LED Lamp for incentivized LED replacement lamps. These criteria go beyond energy efficiency

  9. Pousset, Obein, Razet, LED lighting quality with CQS samples CIE 2010 : Lighting Quality and Energy Efficiency, 14-17 March 2010, Vienna, Austria 1

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    A psychophysical experiment developed to evaluate light quality of Light Emitting Diodes (LEDs) is described. Keywords: Light Emitting Diode, quality of light, Color Rendering Index, Color Quality Scale, visual

  10. Development of Advanced LED Phosphors by Spray-based Processes for Solid State Lighting

    SciTech Connect (OSTI)

    Cabot Corporation

    2007-09-30T23:59:59.000Z

    The overarching goal of the project was to develop luminescent materials using aerosol processes for making improved LED devices for solid state lighting. In essence this means improving white light emitting phosphor based LEDs by improvement of the phosphor and phosphor layer. The structure of these types of light sources, displayed in Figure 1, comprises of a blue or UV LED under a phosphor layer that converts the blue or UV light to a broad visible (white) light. Traditionally, this is done with a blue emitting diode combined with a blue absorbing, broadly yellow emitting phosphor such as Y{sub 3}Al{sub 5}O{sub 12}:Ce (YAG). A similar result may be achieved by combining a UV emitting diode and at least three different UV absorbing phosphors: red, green, and blue emitting. These emitted colors mix to make white light. The efficiency of these LEDs is based on the combined efficiency of the LED, phosphor, and the interaction between the two. The Cabot SSL project attempted to improve the over all efficiency of the LED light source be improving the efficiency of the phosphor and the interaction between the LED light and the phosphor. Cabot's spray based process for producing phosphor powders is able to improve the brightness of the powder itself by increasing the activator (the species that emits the light) concentration without adverse quenching effects compared to conventional synthesis. This will allow less phosphor powder to be used, and will decrease the cost of the light source; thus lowering the barrier of entry to the lighting market. Cabot's process also allows for chemical flexibility of the phosphor particles, which may result in tunable emission spectra and so light sources with improved color rendering. Another benefit of Cabot's process is the resulting spherical morphology of the particles. Less light scattering results when spherical particles are used in the phosphor layer (Figure 1) compared to when conventional, irregular shaped phosphor particles are used. This spherical morphology will result in better light extraction and so an improvement of efficiency in the overall device. Cabot is a 2.5 billion dollar company that makes specialized materials using propriety spray based technologies. It is a core competency of Cabot's to exploit the spray based technology and resulting material/morphology advantages. Once a business opportunity is clearly identified, Cabot is positioned to increase the scale of the production to meet opportunity's need. Cabot has demonstrated the capability to make spherical morphology micron-sized phosphor powders by spray based routes for PDP and CRT applications, but the value proposition is still unproven for LED applications. Cabot believes that the improvements in phosphor powders yielded by their process will result in a commercial advantage over existing technologies. Through the SSL project, Cabot has produced a number of different compositions in a spherical morphology that may be useful for solid state lights, as well as demonstrated processes that are able to produce particles from 10 nanometers to 3 micrometers. Towards the end of the project we demonstrated that our process produces YAG:Ce powder that has both higher internal quantum efficiency (0.6 compared to 0.45) and external quantum efficiency (0.85 compared to 0.6) than the commercial standard (see section 3.4.4.3). We, however, only produced these highly bright materials in research and development quantities, and were never able to produce high quantum efficiency materials in a reproducible manner at a commercial scale.

  11. Demonstration Assessment of Light-Emitting Diode (LED) Roadway Lighting at the I-35W Bridge, Minneapolis, MN

    SciTech Connect (OSTI)

    Kinzey, Bruce R.; Myer, Michael

    2009-08-31T23:59:59.000Z

    This report describes the process and results of a demonstration of solid-state lighting (SSL) technology conducted in 2009 at the recently reconstructed I-35W bridge in Minneapolis, MN. The project was supported under the U.S. Department of Energy (DOE) Solid-State Lighting GATEWAY Technology Demonstration Program. Other participants in the demonstration project included the Minnesota Department of Transportation (Mn/DOT), Federal Highways Administration (FHWA), and BetaLED™ (a division of Ruud Lighting). Pacific Northwest National Laboratory (PNNL) conducted the measurements and analysis of the results. DOE has implemented a three-year evaluation of the LED luminaires in this installation in order to develop new longitudinal field data on LED performance in a challenging, real-world environment. This document provides information through the initial phase of the I-35W bridge project, up to and including the opening of the bridge to the public and the initial feedback received on the LED lighting installation from bridge users. Initial findings of the evaluation are favorable, with minimum energy savings level of 13% for the LED installation relative to the simulated base case using 250W high-pressure sodium (HPS) fixtures. The LEDs had an average illuminance level of 0.91 foot candles compared to 1.29 fc for the HPS lamps. The LED luminaires cost $38,000 more than HPS lamps, yielding a lengthy payback period, however the bridge contractor had offered to include the LED luminaires as part of the construction package at no additional cost. One potentially significant benefit of the LEDs in this installation is avoiding rolling lane closures on the heavily-traveled interstate bridge for the purpose of relamping the HPS fixtures. Rolling lane closures involve multiple crew members and various maintenance and safety vehicles, diversion of traffic, as well as related administrative tasks (e.g., approvals, scheduling, etc.). Mn/DOT records show an average cost of relamping fixtures along interstate roadways of between $130-150 per pole. The previous bridge saw a lamp mortality rate of approximately 50% every two years, though the new bridge was designed to minimize many of the vibration issues. A voluntary Web-based feedback survey of nearly 500 self-described bridge users showed strong preference for the LED lighting - positive comments outnumbered negative ones by about five-to-one.

  12. Calibration of Cangaroo II Telescope Using a Fast Blue LED Light Flasher

    E-Print Network [OSTI]

    Enomoto, Ryoji

    , as well as test the data acquisition electronics. Our technique is an independent variation of the laser , and a risetime of #24; 1 ns. The LED has a double emitter giving a non-uniform light pool. By drilling a small

  13. Advanced method for increasing the efficiency of white light quantum dot LEDs

    SciTech Connect (OSTI)

    Duty, Chad E [ORNL; Bennett, Charlee J C [ORNL; Sabau, Adrian S [ORNL; Jellison Jr, Gerald Earle [ORNL; Boudreaux, Philip R [ORNL; Walker, Steven C [ORNL; Ott, Ronald D [ORNL

    2011-01-01T23:59:59.000Z

    Covering a light-emitting diode (LED) with quantum dots (QDs) can produce a broad spectrum of white light. However, current techniques for applying QDs to LEDs suffer from a high density of defects and a non-uniform distribution of QDs, which, respectively, diminish the efficiency and quality of emitted light. Oak Ridge National Laboratory (ORNL) has the unique capability to thermally anneal QD structures at extremely high power densities for very short durations. This process, called pulse thermal processing (PTP), reduces the number of point defects while maintaining the size and shape of the original QD nanostructure. Therefore, the efficiency of the QD wavelength conversion layer is improved without altering the emission spectrum defined by the size distribution of theQD nanoparticles. The current research uses a thermal model to predict annealing temperatures during PTP and demonstrates up to a 300% increase in photoluminescence for QDs on passive substrates.

  14. Phosphors for near UV-Emitting LED's for Efficacious Generation of White Light

    SciTech Connect (OSTI)

    McKittrick, Joanna

    2013-09-30T23:59:59.000Z

    1) We studied phosphors for near-UV (nUV) LED application as an alternative to blue LEDs currently being used in SSL systems. We have shown that nUV light sources could be very efficient at high current and will have significantly less binning at both the chip and phosphor levels. We identified phosphor blends that could yield 4100K lamps with a CRI of approximately 80 and LPWnUV,opt equal to 179 for the best performing phosphor blend. Considering the fact that the lamps were not optimized for light coupling, the results are quite impressive. The main bottleneck is an optimum blue phosphor with a peak near 440 nm with a full width half maximum of about 25 nm and a quantum efficiency of >95%. Unfortunately, that may be a very difficult task when we want to excite a phosphor at ~400 nm with a very small margin for Stokes shift. Another way is to have all the phosphors in the blend having the excitation peak at 400 nm or slightly shorter wavelength. This could lead to a white light source with no body color and optimum efficacy due to no self-absorption effects by phosphors in the blend. This is even harder than finding an ideal blue phosphor, but not necessarily impossible. 2) With the phosphor blends identified, light sources using nUV LEDs at high current could be designed with comparable efficacy to those using blue LEDs. It will allow us to design light sources with multiple wattages using the same chips and phosphor blends simply by varying the input current. In the case of blue LEDs, this is not currently possible because varying the current will lower the efficacy at high current and alter the color point. With improvement of phosphor blends, control over CRI could improve. Less binning at the chip level and also at the phosphor blend level could reduce the cost of SSL light sources. 3) This study provided a deeper understanding of phosphor characteristics needed for LEDs in general and nUV LEDs in particular. Two students received Ph.D. degrees and three undergraduates participated in this work. Two of the undergraduate students are now in graduate school. The results were widely disseminated – 20 archival journal publications (published, accepted or in preparation) and three conference proceedings resulted. The students presented their work at 11 different national/international conferences (32 oral or poster presentations) and the PI’s delivered 12 invited, keynote or plenary lectures.

  15. Light-emitting diodes (LEDs), with high efficiency, dimmabil-ity, long life, and directional light output, could be the ideal

    E-Print Network [OSTI]

    The Issue Light-emitting diodes (LEDs), with high efficiency, dimmabil- ity, long life, and directional light output, could be the ideal light source for the common recessed-can downlight. How- ever, many existing LED downlight products fail to live up to expectations, providing poor light distribution

  16. Impact of photonic crystals on LED light extraction efficiency: approaches and limits to vertical structure designs

    SciTech Connect (OSTI)

    Matioli, Elison; Weisbuch, Claude

    2010-01-01T23:59:59.000Z

    The enhancement of the extraction efficiency in light emitting diodes (LEDs) through the use of photonic crystals (PhCs) requires a structure design that optimizes the interaction of the guided modes with the PhCs. The main optimization parameters are related to the vertical structure of the LED, such as the thickness of layers, depth of the PhCs, position of the quantum wells as well as the PhC period and fill factor. We review the impact of the vertical design of different approaches of PhC LEDs through a theoretical and experimental standpoint, assessing quantitatively the competing mechanisms that act over each guided mode. Three approaches are described to overcome the main limitation of LEDs with surface PhCs, i.e. the insufficient interaction of low order guided modes with the PhCs. The introduction of an AlGaN confining layer in such structure is shown to be effective in extracting a fraction of the optical energy of low order modes; however, this approach is limited by the growth of the lattice mismatched AlGaN layer on GaN. The second approach, based on thin-film LEDs with PhCs, is limited by the presence of an absorbing reflective metal layer close to the guided modes that plays a major role in the competition between PhC extraction and metal dissipation. Finally, we demonstrate both experimentally and theoretically the superior extraction of the guided light in embedded PhC LEDs due to the higher interaction between all optical modes and the PhCs, which resulted in a close to unity extraction efficiency for this device. The use of high-resolution angle-resolved measurements to experimentally determine the PhC extraction parameters was an essential tool for corroborating the theoretical models and quantifying the competing absorption and extraction mechanisms in LEDs.

  17. Text-Alternative Version: LED Site Lighting in the Commercial Building Sector: Opportunities, Challenges, and the CBEA Performance Specification

    Broader source: Energy.gov [DOE]

    Below is the text-alternative version of the LED Site Lighting in the Commercial Building Sector: Opportunities, Challenges, and the CBEA Performance Specification webcast.

  18. LED lamp

    DOE Patents [OSTI]

    Galvez, Miguel; Grossman, Kenneth; Betts, David

    2013-11-12T23:59:59.000Z

    There is herein described a lamp for providing white light comprising a plurality of light sources positioned on a substrate. Each of said light sources comprises a blue light emitting diode (LED) and a dome that substantially covers said LED. A first portion of said blue light from said LEDs is transmitted through said domes and a second portion of said blue light is converted into a red light by a first phosphor contained in said domes. A cover is disposed over all of said light sources that transmits at least a portion of said red and blue light emitted by said light sources. The cover contains a second phosphor that emits a yellow light in response to said blue light. The red, blue and yellow light combining to form the white light and the white light having a color rendering index (CRI) of at least about 80.

  19. Self-reported Impacts of LED Lighting Technology Compared to Fuel-based Lighting on Night Market Business Prosperity in Kenya

    E-Print Network [OSTI]

    Johnstone, Peter

    2009-01-01T23:59:59.000Z

    Time period Pre 07/2008 Lighting Technology (Nightly Cost,2 Self-reported Impacts of LED Lighting Technology Comparedto Fuel-based Lighting on Night Market Business Prosperity

  20. Development of Advanced Manufacturing Methods for Warm White LEDs for General Lighting

    SciTech Connect (OSTI)

    Deshpande, Anirudha; Kolodin, Boris; Jacob, Cherian; Chowdhury, Ashfaqul; Kuenzler, Glenn; Sater, Karen; Aesram, Danny; Glaettli, Steven; Gallagher, Brian; Langer, Paul; Setlur, Anant; Beers, Bill

    2012-03-31T23:59:59.000Z

    GE Lighting Solutions will develop precise and efficient manufacturing techniques for the “remote phosphor” platform of warm-white LED products. In volume, this will be demonstrated to drive significant materials, labor and capital productivity to achieve a maximum possible 53% reduction in overall cost. In addition, the typical total color variation for these white LEDs in production will be well within the ANSI bins and as low as a 4-step MacAdam ellipse centered on the black body curve. Achievement of both of these objectives will be demonstrated while meeting a performance target of > 75 lm/W for a warm-white LED and a reliability target of <30% lumen drop / <2-step MacAdam ellipse shift, estimated over 50,000 hrs.

  1. Research on optimization of cooling structure of LED element (The 2nd report)

    SciTech Connect (OSTI)

    Kobayashi, T.; Sakate, Y. [Department of Electronics and Control Engineering, Tsuyama National College of Technology, Okayama (Japan); Hashimoto, R. [Collaborative Research Center, Hiroshima University, Hiroshima (Japan); Takashina, T. [International Industry Academia Collaboration Division, Hiroshima University, Hiroshima (Japan); Kanematsu, H. [Department of Materials Science and Engineering, Suzuka National College of Technology, Mie (Japan); Utsumi, Y. [Laboratory of Advanced Science and Technology for Industry, University of Hyogo, Hyogo (Japan)

    2014-02-20T23:59:59.000Z

    This report shows a design guideline on the parts dimension of LED light bulb for heat transfer. LED light bulb is popular owing to the high efficiency and long life. However, LED element is a point heat source. Therefore, LED light bulb has some problems about heat transfer when it is used for lighting. It sometimes causes deterioration by the raise of local temperature, resulting in lowering of efficiency and shorter life. Thus the thermal analysis focused on the number of element, all parts thickness, length, and radiant heat was studied, as systematic report on the points has not been found. In this report, heat radiation was taken into account in the thermal analysis in addition to natural heat convection. Furthermore the temperature of a heat sink model for LED light bulb was measured with thermocouples and thermo-viewer to verify the calculation. The emissivity of aluminum used for the calculation was 0.4. As the result of analysis, it was found that the maximum temperature was mainly influenced by ring length, ring diameter and disk thickness as a design guideline. Concretely, longer length, larger diameter and thicker disk gave lower temperature of LED element. The temperatures of the best and worst model were around 70 °C and 120 °C respectively in the above condition. The temperatures calculated were consistent with those in experiment.

  2. Design and fabrication of high-index-contrast self-assembled texture for light extraction enhancement in LEDs

    E-Print Network [OSTI]

    Sheng, Xing

    We developed a high-index-contrast photonic structure for improving the light extraction efficiency of light-emitting diodes (LEDs) by a self-assembly approach. In this approach, a two-dimensional grating can be ...

  3. Assessing the Performance of LED-Based Flashlights Available in the Kenyan Off-Grid Lighting Market

    E-Print Network [OSTI]

    Tracy, Jennifer

    2010-01-01T23:59:59.000Z

    testing of emerging off-grid White-LED illumination systems,the economics behind off-grid lighting products for smallAvailable in the Kenyan Off-Grid Lighting Market Jennifer

  4. Demonstration Assessment of Light Emitting Diode (LED) Commercial Garage Lights In the Providence Portland Medical Center, Portland, Oregon

    SciTech Connect (OSTI)

    Ton, My K.; Richman, Eric E.; Gilbride, Theresa L.

    2008-11-11T23:59:59.000Z

    This U.S. Department of Energy GATEWAY Demonstration project studied the applicability of light-emitting diode (LED) luminaires for commercial parking garage applications. High-pressure sodium (HPS) area luminaires were replaced with new LED area luminaires. The project was supported under the U.S. Department of Energy (DOE) Solid State Lighting Program. Other participants in the demonstration project included Providence Portland Medical Center in Portland, Oregon, the Energy Trust of Oregon, and Lighting Sciences Group (LSG) Inc. Pacific Northwest National Laboratory (PNNL) conducted the measurements and analysis of the results. PNNL manages GATEWAY demonstrations for DOE and represents their perspective in the conduct of the work. Quantitative and qualitative measurements of light and electrical power were taken at the site for both HPS and LED light sources. Economic costs were estimated and garage users’ responses to the new light sources were gauged with a survey. Six LED luminaires were installed in the below-ground parking level A, replacing six existing 150W HPS lamps spread out over two rows of parking spaces. Illuminance measurements were taken at floor level approximately every 4 ft on a 60-ft x 40-ft grid to measure light output of these LED luminaires which were termed the “Version 1” luminaires. PNNL conducted power measurements of the circuit in the garage to which the 6 luminaires were connected and determined that they drew an average of 82 W per lamp. An improved LED luminaire, Version 2, was installed in Level B of the parking garage. Illuminance measurements were not made of this second luminaire on site due to higher traffic conditions, but photometric measurements of this lamp and Version 1 were made in an independent testing laboratory and power usage for Version 2 was also measured. Version 1 was found to produce 3600 lumens and Version 2 was found to produce 4700 lumens of light and to consume 78 Watts. Maximum and minimum light levels were measured for the HPS and LED Version 1 luminaires and projected for the Version 2 luminaires. Maximum light levels were 23.51 foot candles, 20.54 fc, and 26.7 fc respectively and minimum light levels were 1.49 fc, 1.45 fc, and 1.88 fc. These results indicate very similar or even slightly higher light levels produced by the LED lamps, despite the higher lumen output of the HPS lamp. The LED lamps provide higher luminaire efficacy because all of the light is directed down and out. None of it is “lost” in the fixture. Also the HPS luminaire had poorly designed optics and a plastic covering that tended to get dirty and cracked, further decreasing the realized light output.[is this an accurate way to say this?] Consumer perceptions of the Version 2 LED were collected via a written survey form given to maintenance and security personnel. More than half felt the LED luminaires provided more light than the HPS lamps and a majority expressed a preference for the new lamps when viewing the relamped area through a security camera. Respondents commented that the LED luminaires were less glary, created less shadows, had a positive impact on visibility, and improved the overall appearance of the area. PNNL conducted an economic analysis and found that the Version 1 lamp produced annual energy savings of 955 kWh and energy cost savings of $76.39 per lamp at electricity rates of 6.5 cents per kWh and $105.03 at 11 cents per kWh. PNNL found that the Version 2 lamp produced annual energy savings of 991 kWh and energy cost savings of $79.26 per lamp at electricity rates of 6.5 cents per kWh and $108.98 at 11 cents per kWh. PNNL also calculated simple payback and found that Version 1 showed paybacks of 5.4 yrs at 6.5c/kWh and 4.1 yrs at 11c/kWh while Version 2 showed paybacks of 5.2 yrs at 6.5c/kWh and 3.9 yrs at 11c/kWh.

  5. Revolutionary Method for Increasing the Efficiency of White Light Quantum Dot LEDs

    SciTech Connect (OSTI)

    Duty, Chad E [ORNL; Bennett, Charlee J C [ORNL; Sabau, Adrian S [ORNL; Jellison Jr, Gerald Earle [ORNL; Boudreaux, Philip R [ORNL; Walker, Steven C [ORNL; Ott, Ronald D [ORNL

    2011-01-01T23:59:59.000Z

    Covering a light-emitting diode (LED) with quantum dots (QDs) can produce a broad spectrum of white light. However, current techniques for applying QDs to LEDs suffer from a high density of defects and a non-uniform distribution of QDs, which respec-tively diminish the efficiency and quality of emitted light. Oak Ridge National Laboratory (ORNL) has the unique capability to thermally anneal QD structures at extremely high power densities for very short durations. This process, called pulse thermal proc-essing (PTP), reduces the number of point defects while main-taining the size and shape of the original QD nanostructure. Therefore, the efficiency of the QD wavelength conversion layer is improved without altering the emission spectrum defined by the size distribution of the quantum dot nanoparticles. The cur-rent research uses a thermal model to predict annealing tempera-tures during PTP and demonstrates up to a 300% increase in pho-toluminescence for QDs on passive substrates

  6. Philips Light Sources & Electronics is Developing an Efficient, Smaller, Cost-Effective Family of LED Drivers

    Broader source: Energy.gov [DOE]

    With the help of DOE funding, Philips Light Sources & Electronics is developing a new family of LED drivers that are more efficient and cost-effective as well as smaller in size than currently available drivers. The new drivers are switch-mode power supplies that are similar to today's drivers, but with an improved design. In addition, they have a different topology—boost plus LLC—for wattages of 40W and above, but they retain the commonly used flyback topology at lower wattages.

  7. Solar LED Light Pilot Project Illuminates the Way in Alabama | Department

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33Frequently AskedEnergyIssues DOE's Nuclear EnergySmart Metersof Energy LED Light Pilot

  8. LED Surgical Task Lighting Scoping Study: A Hospital Energy Alliance Project

    SciTech Connect (OSTI)

    Tuenge, Jason R.

    2011-01-17T23:59:59.000Z

    Tungsten-halogen (halogen) lamps have traditionally been used to light surgical tasks in hospitals, even though they are in many respects ill-suited to the application due to the large percentage of radiant energy outside the visible spectrum and issues with color rendering/quality. Light-emitting diode (LED) technology offers potential for adjustable color and improved color rendition/quality, while simultaneously reducing side-effects from non-visible radiant energy. It also has the potential for significant energy savings, although this is a fairly narrow application in the larger commercial building energy use sector. Based on analysis of available products and Hospital Energy Alliance member interest, it is recommended that a product specification and field measurement procedure be developed for implementation in demonstration projects.

  9. LED Lighting in a Performing Arts Building at the University of Florida

    SciTech Connect (OSTI)

    Miller, Naomi J.; Kaye, Stan; Coleman, Patricia; Wilkerson, Andrea M.; Perrin, Tess E.; Sullivan, Gregory P.

    2014-07-01T23:59:59.000Z

    The U.S. DOE GATEWAY Demonstration Program supports demonstrations of high-performance solid-state lighting (SSL) products in order to develop empirical data and experience with the in-the-field applications of this advanced lighting technology. This report describes the process and results of the 2013 - 2014 GATEWAY demonstration of SSL technology in the Nadine McGuire Theatre and Dance Pavilion at the University of Florida, Gainesville, FL. The LED solutions combined with dimming controls utilized in four interior spaces - the Acting Studio, Dance Studio, Scene Shop, and Dressing Room - received high marks from instructors, students/performers, and reduced energy use in all cases. The report discusses in depth and detail of each project area including specifications, energy savings, and user observations. The report concludes with lessons learned during the demonstration.

  10. Off-grid energy services for the poor: Introducing LED lighting in the Millennium Villages Project in Malawi

    E-Print Network [OSTI]

    Modi, Vijay

    ) powered by batteries, which are in turn charged by grid electricity or small solar panels, have emerged 2009 Keywords: Solar Lighting Development a b s t r a c t Lanterns that use light-emitting diodes (LEDs as a cost-competitive alternative to kerosene and other fuel-based lighting technologies, offering brighter

  11. Development of substrate-removal-free vertical ultraviolet light-emitting diode (RefV-LED)

    SciTech Connect (OSTI)

    Kurose, N., E-mail: kurose@fc.ritsumei.ac.jp; Aoyagi, Y. [The Research Organization of Science and Technology, Ritsumeikan University, 1-1-1, Noji-higashi, Kusatsu, Shiga 525-8577 (Japan)] [The Research Organization of Science and Technology, Ritsumeikan University, 1-1-1, Noji-higashi, Kusatsu, Shiga 525-8577 (Japan); Shibano, K.; Araki, T. [Department of Science and Technology, Ritsumeikan University, 1-1-1, Noji-higashi, Kusatsu, Shiga 525-8577 (Japan)] [Department of Science and Technology, Ritsumeikan University, 1-1-1, Noji-higashi, Kusatsu, Shiga 525-8577 (Japan)

    2014-02-15T23:59:59.000Z

    A vertical ultraviolet (UV) light-emitting diode (LED) that does not require substrate removal is developed. Spontaneous via holes are formed in n-AlN layer epitaxially grown on a high conductive n+Si substrate and the injected current flows directly from the p-electrode to high doped n{sup +} Si substrate through p-AlGaN, multi-quantum wells, n-AlGaN and spontaneous via holes in n-AlN. The spontaneous via holes were formed by controlling feeding-sequence of metal-organic gas sources and NH{sub 3} and growth temperature in MOCVD. The via holes make insulating n-AlN to be conductive. We measured the current-voltage, current-light intensity and emission characteristics of this device. It exhibited a built-in voltage of 3.8 V and emission was stated at 350 nm from quantum wells with successive emission centered at 400?nm. This UV LED can be produced, including formation of n and p electrodes, without any resist process.

  12. LED Update

    SciTech Connect (OSTI)

    Johnson, Mark L.; Gordon, Kelly L.

    2006-09-01T23:59:59.000Z

    This article, which will appear in RESIDENTIAL LIGHTING MAGAZINE, interviews PNNL's Kelly Gordon and presents the interview in question and answer format. The topic is a light emitting diode (LED) lighting also known as solid state lighting. Solid state lighting will be a new category in an energy efficient lighting fixture design competition called Lighting for Tomorrow sponsored by the US Department of Energy Emerging Technologies Office, the American Institute for Lighting, and the Consortium for Energy Efficiency. LED technology has been around since the ’60s, but it has been used mostly for indicator lights on electronics equipment. The big breakthrough was the development in the 1990s of blue LEDs which can be combined with the red and green LEDs that already existed to make white light. LEDs produce 25 to 40 lumens of light per watt of energy used, almost as much as a CFL (50 lumens per watt) and much more efficient than incandescent sources, which are around 15 lumens per watt. They are much longer lived and practical in harsh environments unsuitable for incandescent lighting. They are ready for niche applications now, like under-counter lighting and may be practical for additional applications as technological challenges are worked out and the technology is advancing in leaps and bounds.

  13. Jacketed lamp bulb envelope

    DOE Patents [OSTI]

    MacLennan, Donald A. (Gaithersburg, MD); Turner, Brian P. (Damascus, MD); Gitsevich, Aleksandr (Gaithersburg, MD); Bass, Gary K. (Mt. Airy, MD); Dolan, James T. (Frederick, MD); Kipling, Kent (Gaithersburg, MD); Kirkpatrick, Douglas A. (Great Falls, VA); Leng, Yongzhang (Damascus, MD); Levin, Izrail (Silver Spring, MD); Roy, Robert J. (Frederick, MD); Shanks, Bruce (Gaithersburg, MD); Smith, Malcolm (Alexandria, VA); Trimble, William C. (Columbia, MD); Tsai, Peter (Olney, MD)

    2001-01-01T23:59:59.000Z

    A jacketed lamp bulb envelope includes a ceramic cup having an open end and a partially closed end, the partially closed end defining an aperture, a lamp bulb positioned inside the ceramic cup abutting the aperture, and a reflective ceramic material at least partially covering a portion of the bulb not abutting the aperture. The reflective ceramic material may substantially fill an interior volume of the ceramic cup not occupied by the bulb. The ceramic cup may include a structural feature for aiding in alignment of the jacketed lamp bulb envelope in a lamp. The ceramic cup may include an external flange about a periphery thereof. One example of a jacketed lamp bulb envelope includes a ceramic cup having an open end and a closed end, a ceramic washer covering the open end of the ceramic cup, the washer defining an aperture therethrough, a lamp bulb positioned inside the ceramic cup abutting the aperture, and a reflective ceramic material filling an interior volume of the ceramic cup not occupied by the bulb. A method of packing a jacketed lamp bulb envelope of the type comprising a ceramic cup with a lamp bulb disposed therein includes the steps of filling the ceramic cup with a flowable slurry of reflective material, and applying centrifugal force to the cup to pack the reflective material therein.

  14. How Many CASTLE Bulbs Would You Need To Match the Brightness of the Sun?

    E-Print Network [OSTI]

    Collar, Juan I.

    How Many CASTLE Bulbs Would You Need To Match the Brightness of the Sun? = × ? Please do all million miles), so if we were to try to build the Sun out of light bulbs, we'd need a bunch! But, how many objects: the Sun, and a CASTLE light bulb. What do we mean by "brightness?" The electromagnetic (EM

  15. Numerical Modelling of Light Emission and Propagation in (Organic) LEDs with the Green's Tensor

    E-Print Network [OSTI]

    Floreano, Dario

    light emitting diodes, light emission, light extraction, dipole radiation, stratified media, layered surpasses incandescent sources by a factor of 2 and with further improvements light emitting diodes could on light extraction techniques from inorganic light emitting diodes we recommend chapter 5 in 1 . Organic

  16. Illuminating the Pecking Order in Off-Grid Lighting: A Demonstration of LED Lighting for Saving Energy in the Poultry Sector

    SciTech Connect (OSTI)

    Tracy, Jennifer; Mills, Evan

    2010-11-06T23:59:59.000Z

    The Lumina Project and Lighting Africa conducted a full-scale field test involving a switch from kerosene to solar-LED lighting for commercial broiler chicken production at an off-grid farm in Kenya. The test achieved lower operating costs, produced substantially more light, improved the working environment, and had no adverse effect on yields. A strategy using conventional solar-fluorescent lighting also achieved comparable yields, but entailed a six-fold higher capital cost and significantly higher recurring battery replacement costs. Thanks to higher energy and optical efficiencies, the LED system provided approximately twice the illumination to the chicken-production area and yet drew less than half the power.At the study farm, 3000 chickens were grown in each of three identical houses under kerosene, fluorescent, and LED lighting configurations. Under baseline conditions, a yearly expenditure of 1,200 USD is required to illuminate the three houses with kerosene. The LED system eliminates this fuel use and expense with a corresponding simple payback time of 1.5 years, while the solar-fluorescent system has a payback time of 9.3 years. The corresponding reduction in fuel expenditure in both cases represents a 15percent increase in after-tax net income (revenues minus expenses) across the entire business operation. The differential cost-effectiveness between the LED and fluorescent systems would be substantially greater if the fluorescent system were upsized to provide the same light as the LED system. Providing light with the fluorescent or LED systems is also far more economical than connecting to the grid in this case. The estimated grid-connection cost at this facility is 1.7 million Kenya Schillings (approximately 21,250 USD), which is nearly six-times the cost of the fluorescent system and 35-times the cost of the LED system.The LED system also confers various non-energy benefits. The relative uniformity of LED lighting, compared to the fluorescent or kerosene lighting, reduced crowding which in turn created a less stressful environment for the chickens. The far higher levels of illumination also created a better environment for the workers, while eliminating the time required for obtaining fuel and maintaining kerosene lanterns. An additional advantage of the LED system relative to the solar fluorescent system was that the former does not require a skilled technician to carry out the installation. The portable LED system lighting layout is also more easily adjusted than that of the hardwired fluorescent systems. Furthermore, switching to the LED system avoids over one metric ton of carbon dioxide emissions per house on an annual basis compared to kerosene. There is high potential for replication of this particular LED lighting strategy in the developing world. In order to estimate the scale of kerosene use and the potential for savings, more information is needed on the numbers of chickens produced off-grid, as well as lighting uses for other categories of poultry production (egg layers, indigenous broilers ). Our discovery that weight gain did not slow in the solar-fluorescent house after it experienced extended lighting outages beginning on day 14 of the 35-day study suggests that conventional farming practices in Kenyan broiler operations may call for more hours of lighting than is needed to achieve least-cost production.

  17. Demonstration Assessment of Light-Emitting Diode (LED) Parking Lot Lighting at T.J.Maxx in Manchester, NH Phase I

    SciTech Connect (OSTI)

    Myer, Michael; Goettel, Russell T.

    2010-06-29T23:59:59.000Z

    A report describing the process and results of replacing existing parking lot lighting, looking at a LED option with occupancy sensors, and conventional alternates. Criteria include payback, light levels, occupant satisfaction. This report is Phase I of II. Phase I deals with initial installation.

  18. Demonstration Assessment of LED Roadway Lighting: NE Cully Boulevard Portland, OR

    SciTech Connect (OSTI)

    Royer, Michael P.; Poplawski, Michael E.; Tuenge, Jason R.

    2012-06-29T23:59:59.000Z

    A new roadway lighting demonstration project was initiated in late 2010, which was planned in conjunction with other upgrades to NE Cully Boulevard, a residential collector road in the northeast area of Portland, OR. With the NE Cully Boulevard project, the Portland Bureau of Transportation hoped to demonstrate different light source technologies and different luminaires side-by-side. This report documents the initial performance of six different newly installed luminaires, including three LED products, one induction product, one ceramic metal halide product, and one high-pressure sodium (HPS) product that represented the baseline solution. It includes reported, calculated, and measured performance; evaluates the economic feasibility of each of the alternative luminaires; and documents user feedback collected from a group of local Illuminating Engineering Society (IES) members that toured the site. This report does not contain any long-term performance evaluations or laboratory measurements of luminaire performance. Although not all of the installed products performed equally, the alternative luminaires generally offered higher efficacy, more appropriate luminous intensity distributions, and favorable color quality when compared to the baseline HPS luminaire. However, some products did not provide sufficient illumination to all areas—vehicular drive lanes, bicycle lanes, and sidewalks—or would likely fail to meet design criteria over the life of the installation due to expected depreciation in lumen output. While the overall performance of the alternative luminaires was generally better than the baseline HPS luminaire, cost remains a significant barrier to widespread adoption. Based on the cost of the small quantity of luminaires purchased for this demonstration, the shortest calculated payback period for one of the alternative luminaire types was 17.3 years. The luminaire prices were notably higher than typical prices for currently available luminaires purchased in larger quantities. At prices that are more typical, the payback would be less than 10 years. In addition to the demonstration luminaires, a networked control system was installed for additional evaluation and demonstration purposes. The capability of control system to measure luminaire input power was explored in this study. A more exhaustive demonstration and evaluation of the control system will be the subject of future GATEWAY report(s).

  19. Assessing the Performance of 5mm White LED Light Sources for Developing-Country Applications

    E-Print Network [OSTI]

    Mills, Evan

    2007-01-01T23:59:59.000Z

    with fluorescent lighting for off-grid applications in theProject includes an Off-Grid Lighting Technology Assessmentand the market success of off-grid lighting solutions for

  20. Research Support in Hungary Machine scheduling LED public lighting Microsimulation in public transportation Finally Optimization and Operation Research methods for

    E-Print Network [OSTI]

    Balázs, Bánhelyi

    Euros per full time researcher year. The Hungarian research support scheme has several other smallerResearch Support in Hungary Machine scheduling LED public lighting Microsimulation in public transportation Finally Optimization and Operation Research methods for Real Life Industrial Problems Tibor

  1. DOE Publishes GATEWAY Report on High-Luminous-Flux LED Lighting...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of the lighting system, despite the reduction in pole height. The combination of the optics and lower pole height reduced stray light considerably. The expected annual...

  2. Text-Alternative Version: LED Lighting in a Performing Arts Building Webinar

    Broader source: Energy.gov [DOE]

     Welcome ladies and gentlemen. I'm Bob Davis with the Pacific Northwest National Laboratory, and I'd like to welcome you to today's webcast titled, LEDs, Can They Perform in a Performing Arts...

  3. Essays on Environmental and Resource Economics

    E-Print Network [OSTI]

    Toledo, Chantal Nathalie

    2013-01-01T23:59:59.000Z

    Light Bulb Offer (UC BerkeleyBetween Light Bulbs . . . . . . . . . . . . . . . . .Reasons for the Light Bulb Choice, ILB (left) or LED (right)

  4. Fundamental Studies and Development of III-N Visible LEDs for High-Power Solid-State Lighting Applications

    SciTech Connect (OSTI)

    Dupuis, Russell

    2012-02-29T23:59:59.000Z

    The goal of this program is to understand in a fundamental way the impact of strain, defects, polarization, and Stokes loss in relation to unique device structures upon the internal quantum efficiency (IQE) and efficiency droop (ED) of III-nitride (III-N) light-emitting diodes (LEDs) and to employ this understanding in the design and growth of high-efficiency LEDs capable of highly-reliable, high-current, high-power operation. This knowledge will be the basis for our advanced device epitaxial designs that lead to improved device performance. The primary approach we will employ is to exploit new scientific and engineering knowledge generated through the application of a set of unique advanced growth and characterization tools to develop new concepts in strain-, polarization-, and carrier dynamics-engineered and low-defect materials and device designs having reduced dislocations and improved carrier collection followed by efficient photon generation. We studied the effects of crystalline defect, polarizations, hole transport, electron-spillover, electron blocking layer, underlying layer below the multiplequantum- well active region, and developed high-efficiency and efficiency-droop-mitigated blue LEDs with a new LED epitaxial structures. We believe new LEDs developed in this program will make a breakthrough in the development of high-efficiency high-power visible III-N LEDs from violet to green spectral region.

  5. Light extraction in individual GaN nanowires on Si for LEDs

    E-Print Network [OSTI]

    Zhou, Xiang

    GaN-based nanowires hold great promise for solid state lighting applications because of their waveguiding properties and the ability to grow nonpolar GaN nanowire-based heterostructures, which could lead to increased light ...

  6. Demonstration Assessment of Light-Emitting Diode (LED) Roadway Lighting on Residential and Commercial Streets in Palo Alto, CA

    SciTech Connect (OSTI)

    Myer, Michael; Kinzey, Bruce R.; Tam, Christine

    2010-06-24T23:59:59.000Z

    This report is part of a GATEWAY demonstration that replaced existing HPS streetlights with two different types of LED products and one induction product. Energy savings ranged from 6% to 44%.

  7. Demonstration Assessment of Light-Emitting Diode (LED) Retrofit Lamps at the Lobby of the Bonneville Power Administration, Portland, OR

    SciTech Connect (OSTI)

    Miller, Naomi

    2011-07-01T23:59:59.000Z

    This report describes the process and results of a demonstration of solid-state lighting (SSL) technology in the lobby of the Bonneville Power Administration (BPA) headquarters building in Portland, Oregon. The project involved a simple retrofit of 32 track lights used to illuminate historical black-and-white photos and printed color posters from the 1930s and 1940s. BPA is a federal power marketing agency in the Northwestern United States, and selected this prominent location to demonstrate energy efficient light-emitting diode (LED) retrofit options that not only can reduce the electric bill for their customers but also provide attractive alternatives to conventional products, in this case accent lighting for BPA's historical artwork.

  8. Municipal Consortium LED Street Lighting Workshop Presentations and Materials—Los Angeles, CA

    Broader source: Energy.gov [DOE]

    This page provides links to the presentations given at the DOE Municipal Solid-State Street Lighting Consortium Workshop held in Los Angeles April 19–20, 2012.

  9. Municipal Consortium LED Street Lighting Workshop Presentations and Materials—Dallas, TX

    Broader source: Energy.gov [DOE]

    This page provides links to the presentations given at the DOE Municipal Solid-State Street Lighting Consortium Workshop held in Dallas March 15–16, 2012.

  10. Municipal Consortium LED Street Lighting Workshop: April 19–20, Los Angeles, CA

    Broader source: Energy.gov [DOE]

    Workshop Location: The Sheraton Los Angeles Downtown Hotel, 711 Hope Street, Los Angeles, CA 90017City Partner: City of Los Angeles Bureau of Street LightingCost: $175

  11. Municipal Consortium LED Street Lighting Workshop Presentations and Materials—Boston, MA

    Broader source: Energy.gov [DOE]

    This page provides links to the presentations given at the DOE Municipal Solid-State Street Lighting Consortium Workshop held in Boston August 2–3, 2012.

  12. Jade Sky Technologies Partners with CLTC on LED Replacement Lamp Upgrade Project UC Davis' California Lighting Technology Center will utilize Jade Sky Technologies' driver ICs to help spur

    E-Print Network [OSTI]

    California at Davis, University of

    Jade Sky Technologies Partners with CLTC on LED Replacement Lamp Upgrade Project UC Davis and power factor. "JST shares our goal of making the transition to LED lamps a satisfying experience of cost-effective, easy-to-use LED lighting solutions Milpitas, Calif. ­ October 15, 2013 ­ Jade Sky

  13. Portable leD ViDeo light SyStem USER'S GUIDE

    E-Print Network [OSTI]

    Jacobs, Laurence J.

    first use. Beyond the initial charge, no additional battery conditioning is required. a. PlugD lighting system 2 Package Contents 2 Miniburst Controllers & Connectors 4 Charging the battery 5 operatingBurst lights can be plugged directly into a standard AC outlet to power the unit for longer shoots. b. Battery

  14. Demonstration Assessment of Light Emitting Diode (LED) Walkway Lighting at the Federal Aviation Administration William J. Hughes Technical Center, in Atlantic City, New Jersey

    SciTech Connect (OSTI)

    Kinzey, Bruce R.; Myer, Michael

    2008-03-18T23:59:59.000Z

    This report documents the results of a collaborative project to demonstrate a solid state lighting (SSL) general illumination product in an outdoor area walkway application. In the project, six light-emitting diode (LED) luminaires were installed to replace six existing high pressure sodium (HPS) luminaires mounted on 14-foot poles on a set of exterior walkways and stairs at the Federal Aviation Administration (FAA) William J. Hughes Technical Center in Atlantic City, New Jersey, during December, 2007. The effort was a U.S. Department of Energy (DOE) SSL Technology Gateway Demonstration that involved a collaborative teaming agreement between DOE, FAA and Ruud Lighting (and their wholly owned division, Beta LED). Pre- and post-installation power and illumination measurements were taken and used in calculations of energy savings and related economic payback, while personnel impacted by the new lights were provided questionnaires to gauge their perceptions and feedback. The SSL product demonstrated energy savings of over 25% while maintaining illuminance levels and improving illuminance uniformity. PNNL's economic analysis yielded a variety of potential payback results depending on the assumptions used. In the best case, replacing HPS with the LED luminaire can yield a payback as low as 3 years. The new lamps were quite popular with the affected personnel, who gave the lighting an average score of 4.46 out of 5 for improvement.

  15. Assessing the Performance of LED-Based Flashlights Available in the Kenyan Off-Grid Lighting Market

    SciTech Connect (OSTI)

    Tracy, Jennifer; Jacobson, Arne; Mills, Evan

    2010-03-02T23:59:59.000Z

    Low cost rechargeable flashlights that use LED technology are increasingly available in African markets. While LED technology holds promise to provide affordable, high quality lighting services, the widespread dissemination of low quality products may make it difficult to realize this potential. This study includes performance results for three brands of commonly available LED flashlights that were purchased in Kenya in 2009. The performance of the flashlights was evaluated by testing five units for each of the three brands. The tests included measurements of battery capacity, time required to charge the battery, maximum illuminance at one meter, operation time and lux-hours from a fully charged battery, light distribution, and color rendering. All flashlights tested performed well below the manufacturers? rated specifications; the measured battery capacity was 30-50percent lower than the rated capacity and the time required to fully charge the battery was 6-25percent greater than the rated time requirement. Our analysis further shows that within each brand there is considerable variability in each performance indicator. The five samples within a single brand varied from each other by as much as 22percent for battery capacity measurements, 3.6percent for the number of hours required for a full charge, 23percent for maximum initial lux, 38percent for run time, 11percent for light distribution and by as much as 200percent for color rendering. Results obtained are useful for creating a framework for quality assurance of off-grid LED products and will be valuable for informing consumers, distributors and product manufacturers about product performance.

  16. Self-reported Impacts of LED Lighting Technology Compared to Fuel-based Lighting on Night Market Business Prosperity in Kenya

    SciTech Connect (OSTI)

    Johnstone, Peter; Jacobson, Arne; Mills, Evan; Mumbi, Maina

    2009-02-11T23:59:59.000Z

    The notion of"productive use" is often invoked in discussions about whether new technologies improve productivity or otherwise enhance commerce in developing-country contexts. It an elusive concept,especially when quantitative measures are sought. Improved and more energy efficient illumination systems for off-gridapplication--the focus of the Lumina Project--provide a case in which a significant productivity benefit can be imagined, given the importance of light to the successful performance of many tasks, and the very low quality of baseline illumination provided by flame-based source. This Research Note summarizes self-reported quantitative and qualitative impacts of switching to LED lighting technology on the prosperity of night-market business owners and operators. The information was gathered in the context of our 2008 market testing field work in Kenya?s Rift Valley Province, which was performed in the towns of Maai Mahiu and Karagita by Arne Jacobson, Kristen Radecsky, Peter Johnstone, Maina Mumbi, and others. Maai Mahiu is a crossroads town; provision of services to travelers and freight carriers is a primary income source for the residents. In contrast, the primary income for Karagita's residents is from work in the large, factory style flower farms on the eastern shores of Lake Naivasha that specialize in producing cut flowers for export to the European market. According to residents, both towns had populations of 6,000 to 8,000 people in June 2008. We focused on quantifying the economics of fuel-based and LED lighting technology in the context of business use by night market vendors and shop keepers. Our research activities with the business owners and operators included baseline measurement of their fuel-based lighting use, an initial survey, offering for sale data logger equipped rechargeable LED lamps, monitoring the adoption of the LED lamps, and a follow-up survey.

  17. Two-color photoionization of calcium using SHG and LED light

    E-Print Network [OSTI]

    Schuck, C; Almendros, M; Hennrich, M; Eschner, J

    2009-01-01T23:59:59.000Z

    We present a photoionization method to load single 40Ca ions in a linear Paul trap from an atomic beam. Neutral Ca I atoms are resonantly excited from the ground state to the intermediate 4s4p 1P_1-level using coherent 423nm radiation produced by single-pass second harmonic generation in a periodically poled KTiOPO_4 crystal pumped with an 120mW extended cavity diode laser. Ionization is then attained with a high-power light emitting diode imaged to the trap center, using an appropriately designed optical system composed of standard achromatic doublet lenses. The setup simplifies previous implementations at similar efficiency, and it hardly requires any maintenance at all.

  18. Two-color photoionization of calcium using SHG and LED light

    E-Print Network [OSTI]

    C. Schuck; F. Rohde; M. Almendros; M. Hennrich; J. Eschner

    2009-11-19T23:59:59.000Z

    We present a photoionization method to load single 40Ca ions in a linear Paul trap from an atomic beam. Neutral Ca I atoms are resonantly excited from the ground state to the intermediate 4s4p 1P_1-level using coherent 423nm radiation produced by single-pass second harmonic generation in a periodically poled KTiOPO_4 crystal pumped with an 120mW extended cavity diode laser. Ionization is then attained with a high-power light emitting diode imaged to the trap center, using an appropriately designed optical system composed of standard achromatic doublet lenses. The setup simplifies previous implementations at similar efficiency, and it hardly requires any maintenance at all.

  19. Ordered progression of nematogenesis from stem cells through differentiation stages in the tentacle bulb of Clytia hemisphaerica (Hydrozoa, Cnidaria)

    E-Print Network [OSTI]

    Gibson, Matt

    bulb of Clytia hemisphaerica (Hydrozoa, Cnidaria) Elsa Denker, Michaël Manuel, Lucas Leclère, Hervé Le of the tentacle bulb, a specialized swelling at the tentacle base. Analysis by a variety of light and electron-temporal characteristics are markedly more ordered. The tentacle bulb nematogenic ectoderm (TBE) was found to be polarized

  20. Assessing the Performance of LED-Based Flashlights Available in the Kenyan Off-Grid Lighting Market

    E-Print Network [OSTI]

    Tracy, Jennifer

    2010-01-01T23:59:59.000Z

    30), 477-499. Efficient Lighting Initiative. 2004. Lighting Energy Bill, Internationalfor Energy-Efficient Lighting and Lawrence Berkeley National

  1. Self-reported Impacts of LED Lighting Technology Compared to Fuel-based Lighting on Night Market Business Prosperity in Kenya

    E-Print Network [OSTI]

    Johnstone, Peter

    2009-01-01T23:59:59.000Z

    s kiosk illuminated by her LED lamp [1/2009] “A.N. ” Market:charge at a shop) “The [LED] lamp is very important and mylamp, hurricane lamp, and LED lamp illuminate night market

  2. Dendritic processing within olfactory bulb circuits

    E-Print Network [OSTI]

    Betz, William J.

    Dendritic processing within olfactory bulb circuits Nathan E. Schoppa1 and Nathan N. Urban2 1 of the olfactory bulb. How- ever, the mechanisms by which this map is transformed into an odor code by the bulb circuitry remain unclear. Recent physiological studies in bulb slices have ident- ified several synaptic

  3. LEDs_3LEDs_3 current efficiency

    E-Print Network [OSTI]

    Pulfrey, David L.

    efficiencySec. 8.2 From our toolbox Current efficiency #12;4 Light extraction efficiencyLight extraction extraction efficiencyDesign to improve extraction efficiencySec. 8.4 What are the features of this LED from;6 Various efficienciesVarious efficienciesSecs. 8.4, 8.5 Present record is 56%Wall-plug efficiency Wall

  4. Synthesis and luminescence properties of rare earth activated phosphors for near UV-emitting LEDs for efficacious generation of white light

    E-Print Network [OSTI]

    Han, Jinkyu

    2013-01-01T23:59:59.000Z

    high-color-rendering LED lamps using oxyfluoride andin white LED. (a) Typical LED lamp package. (b) Uniformin white LED. (a) Typical LED lamp package. (b) Uniform

  5. Self-reported Impacts of LED Lighting Technology Compared to Fuel-based Lighting on Night Market Business Prosperity in Kenya

    E-Print Network [OSTI]

    Johnstone, Peter

    2009-01-01T23:59:59.000Z

    Pre 07/2008 Lighting Technology (Nightly Cost, Ksh) Pressure07/2008 Lighting Technology (Nightly Cost, Ksh) Hurricane07/2008 Lighting Technology (Nightly Cost, Ksh) Hurricane

  6. Potential Environmental Impacts from the Metals in Incandescent, Compact Fluorescent Lamp (CFL), and Light-Emitting Diode (LED)

    E-Print Network [OSTI]

    Short, Daniel

    the lighting products are to be categorized as hazardous waste under existing U.S. federal and California state in lighting products without compromising their performance and useful lifespan. INTRODUCTION The U.S. Energy to increase energy efficiency for general lighting. Therefore, consumers are replacing incandescent light

  7. Illuminating the Pecking Order in Off-Grid Lighting: A Demonstration of LED Lighting for Saving Energy in the Poultry Sector

    E-Print Network [OSTI]

    Tracy, Jennifer

    2012-01-01T23:59:59.000Z

    workers in comparison to the other lighting systems. Therelamps. 3. In comparison to the other lighting systems, the

  8. Sandia National Laboratories: LED

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    electroluminescence was first reported by H.J. Round in 1907, and the first light-emitting diode (LED) was reported by O.V. Losev in 1927. Not until the birth of semiconductor...

  9. LED Record Efficacy and Brightness

    Broader source: Energy.gov [DOE]

    Designed for general lighting applications such as street, industrial, and parking garage lighting, the Cree XLamp® power LED sets new records for LED brightness and efficacy, up to 85 lm/W at 350 mA. The XLamp utilizes Cree's performance breakthrough EZBright™ LED chip; both products include technology that was developed in part with R&D funding support from DOE.

  10. The evolving price of household LED lamps: Recent trends and historical comparisons for the US market

    SciTech Connect (OSTI)

    Gerke, Brian F.; Ngo, Allison T.; Alstone, Andrea L.; Fisseha, Kibret S.

    2014-10-14T23:59:59.000Z

    In recent years, household LED light bulbs (LED A lamps) have undergone a dramatic price decline. Since late 2011, we have been collecting data, on a weekly basis, for retail offerings of LED A lamps on the Internet. The resulting data set allows us to track the recent price decline in detail. LED A lamp prices declined roughly exponentially with time in 2011-2014, with decline rates of 28percent to 44percent per year depending on lumen output, and with higher-lumen lamps exhibiting more rapid price declines. By combining the Internet price data with publicly available lamp shipments indices for the US market, it is also possible to correlate LED A lamp prices against cumulative production, yielding an experience curve for LED A lamps. In 2012-2013, LED A lamp prices declined by 20-25percent for each doubling in cumulative shipments. Similar analysis of historical data for other lighting technologies reveals that LED prices have fallen significantly more rapidly with cumulative production than did their technological predecessors, which exhibited a historical decline of 14-15percent per doubling of production.

  11. Illuminating the Pecking Order in Off-Grid Lighting: A Demonstration of LED Lighting for Saving Energy in the Poultry Sector

    E-Print Network [OSTI]

    Tracy, Jennifer

    2012-01-01T23:59:59.000Z

    the Pecking Order in Off-Grid Lighting A Demonstration ofanalysis and information on off-grid lighting solutions fordevelopment of commercial off-grid lighting markets in Sub-

  12. Illuminating the Pecking Order in Off-Grid Lighting: A Demonstration of LED Lighting for Saving Energy in the Poultry Sector

    E-Print Network [OSTI]

    Tracy, Jennifer

    2012-01-01T23:59:59.000Z

    each of the three systems. Lighting System Kerosene Solar-opened and all available lighting points in use—we measuredin comparison to the other lighting systems. There is

  13. Stochastic modeling of hourly dry-bulb and wet-bulb temperatures

    SciTech Connect (OSTI)

    Kline, D.E.; Woeste, F.E.

    1984-01-01T23:59:59.000Z

    A stochastic model of hourly dry-bulb and wet-bulb temperatures was developed. The periodic variations over the course of a year were estimated by least-square approximation. A multisite Markov model was used to simulate the stochastic nature of the data. These two models were combined to simulate years of hourly dry-bulb and wet-bulb temperatures.

  14. Fooling Mother Nature: Forcing Flower Bulbs

    E-Print Network [OSTI]

    Liskiewicz, Maciej

    Fooling Mother Nature: Forcing Flower Bulbs for Indoor Bloom by George Graine,Virginia Cooperative Bulbs for Indoor Bloom George Graine,Virginia Cooperative Extension Master Gardener, Fairfax County, VA Introduction Have you ever wondered if it is possible to enjoy the beauty of bulbs in the middle of winter

  15. Sandia National Laboratories: high-brightness LED

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Partnership, Research & Capabilities, Solid-State Lighting Solid state lighting (SSL), which uses light-emitting diodes (LEDs), has the potential to be 10 times more energy...

  16. S 1.1.1 Highly Polarized Non-polar GaN-based LED Unpolarized LED

    E-Print Network [OSTI]

    Lü, James Jian-Qiang

    Jiaxiang Zhang Solution: Smart Lighting Solid state lighting + Control theory + Animal experiments are advancing solid state devices to move lighting beyond the Bulb and improve human health." Drinking WaterN-based power electronics. Common Vision ­ · Incorporate smart lighting features in everyday lighting fixtures

  17. Self-reported Impacts of LED Lighting Technology Compared to Fuel-based Lighting on Night Market Business Prosperity in Kenya

    E-Print Network [OSTI]

    Johnstone, Peter

    2009-01-01T23:59:59.000Z

    Project includes an Off-Grid Lighting Technology Assessmentand the market success of off-grid lighting solutions forillumination systems for off-grid application—the focus of

  18. Demonstration Assessment of Light-Emitting Diode (LED) Retrofit Lamps at Intercontinental Hotel in San Francisco, CA

    SciTech Connect (OSTI)

    Miller, Naomi J.; Curry, Ku'Uipo J.

    2010-11-01T23:59:59.000Z

    This document is a report of observations and results obtained from a lighting demonstration project conducted under the U.S. Department of Energy (DOE) GATEWAY Demonstration Program. The program supports demonstrations of high-performance solid-state lighting (SSL) products in order to develop empirical data and experience with in-the-field applications of this advanced lighting technology. The DOE GATEWAY Demonstration Program focuses on providing a source of independent, third-party data for use in decision-making by lighting users and professionals; this data should be considered in combination with other information relevant to the particular site and application under examination. Each GATEWAY Demonstration compares SSL products against the incumbent technologies used in that location. Depending on available information and circumstances, the SSL product may also be compared to alternate lighting technologies. Though products demonstrated in the GATEWAY program have been prescreened and tested to verify their actual performance, DOE does not endorse any commercial product or in any way guarantee that users will achieve the same results through use of these products.

  19. (bulb) , (1) Gas(1) Gas(1) Gas(1) Gas----saturation methodsaturation methodsaturation methodsaturation method

    E-Print Network [OSTI]

    Hong, Deog Ki

    (bulb) , . . , . . 1. . (1) Gas(1Static MethodStatic Method Isoteniscope bulb U-tube . bulb U-tube bulb . bulb . U bulb . manometer . . Isoteniscope Boling Point Method . #12;2. (1) Boiling

  20. Lighting a building with a single bulb : toward a system for illumination in the 21st c.; or, A centralized illumination system for the efficient decoupling and recovery of lighting related heat

    E-Print Network [OSTI]

    Levens, Kurt Antony, 1961-

    1997-01-01T23:59:59.000Z

    Piping light represents the first tenable method for recovery and reutilization of lighting related heat. It can do this by preserving the energy generated at the lamp as radiative, departing from precedent and avoiding ...

  1. Ceramic Mugs & Dishes Incandescent Light Bulbs

    E-Print Network [OSTI]

    Yamamoto, Keith

    , MU East Rock Hall/19-B CELL PHONES - EYEGLASSES 654 Minnesota Street Room 208, copy room CVRI Helen. Zion Cancer Research Building N423 Parnassus Campus: eyeglasses "I" level, Optometry Store, MU West

  2. Type of Space Bulb Type #/House Fixture Style Greenhouse #

    E-Print Network [OSTI]

    Pawlowski, Wojtek

    Type of Space Bulb Type #/House Fixture Style Greenhouse # 1 Lu 430/Lu 400 24 White box style 2 Lu No bulbs 0 N/A Seed harvest room F32 T8/TL 841 90 bulbs VIGS Room F032 /741/ECO 60 bulbs Chamber Model Bulb

  3. Series Input Modular Architecture for Driving Multiple LEDs

    E-Print Network [OSTI]

    , where each cell drives four 700 mA LEDs. Keywords ­ solid-state lighting, light emitting diodes, LED have been achieved over the past decade in solid state light emitting diodes (LEDs), leading to high

  4. A Practical Primer to LED Technology

    Broader source: Energy.gov (indexed) [DOE]

    heatsink is what allows the high flux LED to generate much more light An LED (Light Emitting Diode) consists of a chip of semiconducting material treated to create a structure...

  5. High Efficiency m-plane LEDs on Low Defect Density Bulk GaN Substrates

    SciTech Connect (OSTI)

    David, Aurelien

    2012-10-15T23:59:59.000Z

    Solid-state lighting is a key technology for reduction of energy consumption in the US and worldwide. In principle, by replacing standard incandescent bulbs and other light sources with sources based on light-emitting diodes (LEDs), ultimate energy efficiency can be achieved. The efficiency of LEDs has improved tremendously over the past two decades, however further progress is required for solid- state lighting to reach its full potential. The ability of an LED at converting electricity to light is quantified by its internal quantum efficiency (IQE). The material of choice for visible LEDs is Gallium Nitride (GaN), which is at the basis of blue-emitting LEDs. A key factor limiting the performance of GaN LEDs is the so-called efficiency droop, whereby the IQE of the LED decreases significantly at high current density. Despite decades of research, efficiency droop remains a major issue. Since high-current operation is necessary for practical lighting applications, reducing droop is a major challenge for the scientific community and the LED industry. Our approach to solving the droop issue is the use of newly available low-defect-density bulk GaN non-polar substrates. In contrast to the standard foreign substrates (sapphire, silicon carbide, silicon) used in the industry, we have employed native bulk GaN substrates with very low defect density, thus ensuring exquisite material quality and high IQE. Whereas all commercial LEDs are grown along the c-plane crystal direction of GaN, we have used m-plane non-polar substrates; these drastically modify the physical properties of the LED and enable a reduction of droop. With this approach, we have demonstrated very high IQE performance and low droop. Our results focused on violet and blue LEDs. For these, we have demonstrated very high peak IQEs and current droops of 6% and 10% respectively (up to a high current density of 200A.cm-2). All these results were obtained under electrical operation. These high IQE and low droop values are in line with the program’s milestones. They demonstrate that bulk non-polar GaN substrates represent a disruptive technology for LED performance. Application of this technology to real-world products is feasible, provided that the cost of GaN substrates is compatible with the market’s requirement.

  6. Cree LED Lighting Solutions Formerly LED Lighting Fixtures LLF | Open

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are beingZealand JumpConceptual Model, clickInformationNew|CoreCp Holdings Llc JumpIowa:Crawfordsville, Iowa:Energy

  7. Demonstration of LED Street Lighting

    Office of Scientific and Technical Information (OSTI)

    is calculated as the quotient of total lumens delivered to the target area (in this case, vehicular travel lanes) and the laboratory measured input power of the luminaire....

  8. LED Lighting | Department of Energy

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directed off Energy.gov. Are you sure you wantJoin us for #SpaceWeek Join us for #SpaceWeek June 8,

  9. Vapochromic LED

    DOE Patents [OSTI]

    Kunugi, Yoshihito (Hiroshima, JP); Mann, Kent R. (North Oaks, MN); Miller, Larry L. (Minnetonka, MN); Exstrom, Christopher L. (Kearney, NE)

    2003-06-17T23:59:59.000Z

    A sandwich device was prepared by electrodeposition of an insoluble layer of oligomerized tris(4-(2-thienyl)phenyl)amine onto conducting indium-tin oxide coated glass, spin coating the stacked platinum compound, tetrakis(p-decylphenylisocyano)platinum tetranitroplatinate, from toluene onto the oligomer layer, and then coating the platinum complex with aluminum by vapor deposition. This device showed rectification of current and gave electroluminescence. The electroluminescence spectrum (.lambda..sub.max =545 nm) corresponded to the photoluminescence spectrum of the platinum complex. Exposure of the device to acetone vapor caused the electroemission to shift to 575 nm. Exposure to toluene vapor caused a return to the original spectrum. These results demonstrate a new type of sensor that reports the arrival of organic vapors with an electroluminescent signal. The sensor comprises (a) a first electrode; (b) a hole transport layer formed on the first electrode; (c) a sensing/emitting layer formed on the hole transport layer, the sensing/emitting layer comprising a material that changes color upon exposure to the analyte vapors; (d) an electron conductor layer formed on the sensing layer; and (e) a second electrode formed on the electron conductor layer. The hole transport layer emits light at a shorter wavelength than the sensing/emitting layer and at least the first electrode comprises an optically transparent material.

  10. Vapochromic LED

    DOE Patents [OSTI]

    Kunugi, Yoshihito (Hiroshima, JP); Mann, Kent R. (North Oaks, MN); Miller, Larry L. (Minnetonka, MN); Exstrom, Christopher L. (Kearney, NE)

    2002-01-15T23:59:59.000Z

    A sandwich device was prepared by electrodeposition of an insoluble layer of oligomerized tris(4-(2-thienyl)phenyl)amine onto conducting indium-tin oxide coated glass, spin coating the stacked platinum compound, tetrakis(p-decylphenylisocyano)platinum tetranitroplatinate, from toluene onto the oligomer layer, and then coating the platinum complex with aluminum by vapor deposition. This device showed rectification of current and gave electroluminescence. The electroluminescence spectrum (.mu..sub.max =545 nm) corresponded to the photoluminescence spectrum of the platinum complex. Exposure of the device to acetone vapor caused the electroemission to shift to 575 nm. Exposure to toluene vapor caused a return to the original spectrum. These results demonstrate a new type of sensor that reports the arrival of organic vapors with an electroluminescent signal. The sensor comprises (a) a first electrode; (b) a hole transport layer formed on the first electrode; (c) a sensing/emitting layer formed on the hole transport layer, the sensing/emitting layer comprising a material that changes color upon exposure to the analyte vapors; (d) an electron conductor layer formed on the sensing layer; and (e) a second electrode formed on the electron conductor layer. The hole transport layer emits light at a shorter wavelength than the sensing/emitting layer and at least the first electrode comprises an optically transparent material.

  11. Sandia National Laboratories: white LED

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    electroluminescence was first reported by H.J. Round in 1907, and the first light-emitting diode (LED) was reported by O.V. Losev in 1927. Not until the birth of semiconductor...

  12. Sandia National Laboratories: Red LED

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    electroluminescence was first reported by H.J. Round in 1907, and the first light-emitting diode (LED) was reported by O.V. Losev in 1927. Not until the birth of semiconductor...

  13. Sandia National Laboratories: Blue LED

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    electroluminescence was first reported by H.J. Round in 1907, and the first light-emitting diode (LED) was reported by O.V. Losev in 1927. Not until the birth of semiconductor...

  14. Department of Energy Announces Philips Lighting North America...

    Energy Savers [EERE]

    Product Delivers on Department's Challenge to Replace Common Light Bulb with Energy-Saving Lighting Alternative Washington, D.C. - The U.S. Department of Energy today...

  15. The New York City Bulb Garden [Transforming the American Garden: 12 New Landscape Designs-Exhibitor

    E-Print Network [OSTI]

    Schwartz, Martha

    1986-01-01T23:59:59.000Z

    point of intersection. The bulbs selected for this schemefall and late fall. The bulbs have been selected for theiris designed for flexibility. Bulbs can be replaced and new

  16. Synthesis and luminescence properties of rare earth activated phosphors for near UV-emitting LEDs for efficacious generation of white light

    E-Print Network [OSTI]

    Han, Jinkyu

    2013-01-01T23:59:59.000Z

    LEDs is the significant current droop at high current, whicha binning problem and current droop problems [9]. Thus, theinvestigated due to less current droop and improved binning

  17. Spatial assessment of net mercury emissions from the use of fluorescent bulbs

    SciTech Connect (OSTI)

    Matthew J. Eckelman; Paul T. Anastas; Julie B. Zimmerman [Yale University, New Haven, CT (United States). Department of Chemical Engineering

    2008-11-15T23:59:59.000Z

    While fluorescent lighting is an important technology for reducing electrical energy demand, mercury used in the bulbs is an ongoing concern. Using state and country level data, net emissions of mercury from the marginal use of fluorescent lightbulbs are examined for a base year of 2004 for each of the 50 United States and 130 countries. Combustion of coal for electric power generation is generally the largest source of atmospheric mercury pollution; reduction in electricity demand from the substitution of incandescent bulbs with fluorescents leads to reduced mercury emissions during the use of the bulb. This analysis considers the local mix of power sources, coal quality, thermal conversion efficiencies, distribution losses, and any mercury control technologies that might be in place. Emissions of mercury from production and end-of-life treatment of the bulbs are also considered, providing a life-cycle perspective. Net reductions in mercury over the entire life cycle range from -1.2 to 97 mg per bulb depending on the country. The consequences for atmospheric mercury emissions of several policy scenarios are also discussed. 46 refs., 4 figs., 3 tabs.

  18. LED Replacements for Linear Fluorescent Lamps Webcast

    Broader source: Energy.gov [DOE]

    In this June 20, 2011 webcast on LED products marketed as replacements for linear fluorescent lamps, Jason Tuenge of the Pacific Northwest National Laboratory (PNNL) discussed current Lighting...

  19. Challenges in LED Research and Development

    Broader source: Energy.gov [DOE]

    View the video about LED lighting technology, where it is headed, and the DOE’s role in its continued R&D.

  20. Synthesis and luminescence properties of rare earth activated phosphors for near UV-emitting LEDs for efficacious generation of white light

    E-Print Network [OSTI]

    Han, Jinkyu

    2013-01-01T23:59:59.000Z

    Luo, S. Lu. ?White light emitting diode by using a-Ca 2 P 2silicates for near-UV light emitting diode applications,? J.S.Y. Choi. ?White light-emitting diodes of GaN-based Sr 2

  1. The Somatotopic Organization of the Olfactory Bulb in Elasmobranchs

    E-Print Network [OSTI]

    Kajiura, Stephen

    The Somatotopic Organization of the Olfactory Bulb in Elasmobranchs Tricia L. Meredith,1, University of Colorado Denver, Anschutz Medical Campus, Aurora, Colorado 80045 ABSTRACT The olfactory bulbs-olfac- tory bulbs.'' Somatotopy could provide a preadaptation which facilitated the evolution of olfactory

  2. Cellular/Molecular Detecting Activity in Olfactory Bulb Glomeruli with

    E-Print Network [OSTI]

    Newman, Eric A.

    Cellular/Molecular Detecting Activity in Olfactory Bulb Glomeruli with Astrocyte Recording Didier, Oregon 97239 In the olfactory bulb, axons of olfactory sensory neurons (OSNs) expressing the same to examine functional compartmentalization within and between olfactory bulb glomeruli. Key words: olfactory

  3. BULB: Onion-Based Measuring of OSS Communities

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    BULB: Onion-Based Measuring of OSS Communities Terhi Kilamo1 , Timo Aaltonen1 , and Teemu J. Heinim based on scarce information. In this paper a measuring model for open source commu- nities, BULB, is introduced. BULB provides a way of collecting relevant information and relates it to the well-known onion

  4. Encoding Pheromonal Signals in the Accessory Olfactory Bulb of

    E-Print Network [OSTI]

    Fee, Michale S.

    Encoding Pheromonal Signals in the Accessory Olfactory Bulb of Behaving Mice Minmin Luo,1 * Michale single neurons in the accessory olfactory bulb, a nucleusthatprocessespheromonalsignals with sources of pheromones (4, 5). Olfactory receptor neurons project to the main olfactory bulb (MOB), whose

  5. LED Market Intelligence Report

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    early adopters of LED technologies, particularly around dimming capabilities. 16 LED Market Intelligence Report Home Depot Walmart Cree Philips TCP GE LSG Osram Feit Costco...

  6. LEDs_2LEDs_2 radiative recombination efficiency

    E-Print Network [OSTI]

    Pulfrey, David L.

    (E) lead to a peak in the light intensity. E.F. Schubert, Light-Emitting Diodes, CUP, 2006 [EFS] #12

  7. Multicolor, High Efficiency, Nanotextured LEDs

    SciTech Connect (OSTI)

    Jung Han; Arto Nurmikko

    2011-09-30T23:59:59.000Z

    We report on research results in this project which synergize advanced material science approaches with fundamental optical physics concepts pertaining to light-matter interaction, with the goal of solving seminal problems for the development of very high performance light emitting diodes (LEDs) in the blue and green for Solid State Lighting applications. Accomplishments in the duration of the contract period include (i) heteroepitaxy of nitrogen-polar LEDs on sapphire, (ii) heteroepitaxy of semipolar (11{bar 2}2) green LEDs on sapphire, (iii) synthesis of quantum-dot loaded nanoporous GaN that emits white light without phosphor conversion, (iv) demonstration of the highest quality semipolar (11{bar 2}2) GaN on sapphire using orientation-controlled epitaxy, (v) synthesis of nanoscale GaN and InGaN medium, and (vi) development of a novel liftoff process for manufacturing GaN thin-film vertical LEDs. The body of results is presented in this report shows how a solid foundation has been laid, with several noticeable accomplishments, for innovative research, consistent with the stated milestones.

  8. Microwave generated plasma light source apparatus

    SciTech Connect (OSTI)

    Yoshizawa, K.; Ito, H.; Kodama, H.; Komura, H.; Minowa, Y.

    1985-02-05T23:59:59.000Z

    A microwave generated plasma light source including a microwave generator, a microwave cavity having a light reflecting member forming at least a portion of the cavity, and a member transparent to light and opaque to microwaves disposed across an opening of the cavity opposite the feeding opening through which the microwave generator is coupled. An electrodeless discharge bulb is disposed at a position in the cavity such that the cavity operates as a resonant cavity at least when the bulb is emitting light. In the bulb is encapsulated at least one discharge light emissive substance. The bulb has a shape and is sufficiently small that the bulb acts substantially as a point light source.

  9. EECBG Success Story: Small Nebraska Town Welcomes LEDs and Energy...

    Broader source: Energy.gov (indexed) [DOE]

    historic square, built in the 1850's, is about to become home to something new: LED lights. Learn more. Addthis Related Articles Tecumseh is installing 95 new LED light fixtures...

  10. LED Manufacturing Process Modifications Will Boost Quality and

    E-Print Network [OSTI]

    2012 The Issue Highly energyefficient LightEmitting Diode (LED) lighting products have made great process that will enable LED manufacturers to produce higher quality, energyefficient products at lower

  11. LEDs Go Ivy League: Princeton’s Dillon Gymnasium

    Broader source: Energy.gov [DOE]

    View the video about LED lighting in Dillon Gymnasium, a focal point of sports and recreation at Princeton since 1947. William Evans discusses measurable benefits of LED lighting in the gym and...

  12. Dual LED/incandescent security fixture

    DOE Patents [OSTI]

    Gauna, Kevin Wayne

    2005-06-21T23:59:59.000Z

    A dual LED and incandescent security lighting system uses a hybrid approach to LED illumination. It combines an ambient LED illuminator with a standard incandescent lamp on a motion control sensor. The LED illuminator will activate with the onset of darkness (daylight control) and typically remain on during the course of the night ("always on"). The LED illumination, typically amber, is sufficient to provide low to moderate level lighting coverage to the wall and ground area adjacent to and under the fixture. The incandescent lamp is integrated with a motion control circuit and sensor. When movement in the field of view is detected (after darkness), the incandescent lamp is switched on, providing an increased level of illumination to the area. Instead of an "always on" LED illuminator, the LEDs may also be switched off when the incandescent lamp is switched on.

  13. High Performance Green LEDs by Homoepitaxial

    SciTech Connect (OSTI)

    Wetzel, Christian; Schubert, E Fred

    2009-11-22T23:59:59.000Z

    This work's objective was the development of processes to double or triple the light output power from green and deep green (525 - 555 nm) AlGaInN light emitting diode (LED) dies within 3 years in reference to the Lumileds Luxeon II. The project paid particular effort to all aspects of the internal generation efficiency of light. LEDs in this spectral region show the highest potential for significant performance boosts and enable the realization of phosphor-free white LEDs comprised by red-green-blue LED modules. Such modules will perform at and outperform the efficacy target projections for white-light LED systems in the Department of Energy's accelerated roadmap of the SSL initiative.

  14. White LED with High Package Extraction Efficiency

    SciTech Connect (OSTI)

    Yi Zheng; Matthew Stough

    2008-09-30T23:59:59.000Z

    The goal of this project is to develop a high efficiency phosphor converting (white) Light Emitting Diode (pcLED) 1-Watt package through an increase in package extraction efficiency. A transparent/translucent monolithic phosphor is proposed to replace the powdered phosphor to reduce the scattering caused by phosphor particles. Additionally, a multi-layer thin film selectively reflecting filter is proposed between blue LED die and phosphor layer to recover inward yellow emission. At the end of the project we expect to recycle approximately 50% of the unrecovered backward light in current package construction, and develop a pcLED device with 80 lm/W{sub e} using our technology improvements and commercially available chip/package source. The success of the project will benefit luminous efficacy of white LEDs by increasing package extraction efficiency. In most phosphor-converting white LEDs, the white color is obtained by combining a blue LED die (or chip) with a powdered phosphor layer. The phosphor partially absorbs the blue light from the LED die and converts it into a broad green-yellow emission. The mixture of the transmitted blue light and green-yellow light emerging gives white light. There are two major drawbacks for current pcLEDs in terms of package extraction efficiency. The first is light scattering caused by phosphor particles. When the blue photons from the chip strike the phosphor particles, some blue light will be scattered by phosphor particles. Converted yellow emission photons are also scattered. A portion of scattered light is in the backward direction toward the die. The amount of this backward light varies and depends in part on the particle size of phosphors. The other drawback is that yellow emission from phosphor powders is isotropic. Although some backward light can be recovered by the reflector in current LED packages, there is still a portion of backward light that will be absorbed inside the package and further converted to heat. Heat generated in the package may cause a deterioration of encapsulant materials, affecting the performance of both the LED die and phosphor, leading to a decrease in the luminous efficacy over lifetime. Recent studies from research groups at Rensselaer Polytechnic Institute found that, under the condition to obtain a white light, about 40% of the light is transmitted outward of the phosphor layer and 60% of the light is reflected inward.1,2 It is claimed that using scattered photon extraction (SPE) technique, luminous efficacy is increased by 60%. In this project, a transparent/translucent monolithic phosphor was used to replace the powdered phosphor layer. In the normal pcLED package, the powdered phosphor is mixed with silicone either to be deposited on the top of LED die forming a chip level conversion (CLC) white LED or to be casted in the package forming a volume conversion white LED. In the monolithic phosphors there are no phosphor powder/silicone interfaces so it can reduce the light scattering caused by phosphor particles. Additionally, a multi-layer thin film selectively reflecting filter is inserted in the white LED package between the blue LED die and phosphor layer. It will selectively transmit the blue light from the LED die and reflect the phosphor's yellow inward emission outward. The two technologies try to recover backward light to the outward direction in the pcLED package thereby improving the package extraction efficiency.

  15. Chemical Dependencies of Learning in the Rabbit Olfactory Bulb: Acquisition of the Transient Spatial Pattern Chance Depends on Norepinephrine

    E-Print Network [OSTI]

    Gray, Charles M; Freeman, Walter J III; Skinner, James E

    1986-01-01T23:59:59.000Z

    of neurons in the olfactory bulb following prolonged odorforcbrain (3): Olfactory bulb. anterior olfactory nucleus.39;thc rat olfactory bulb (2): Fluorescnce histochemical.

  16. LED ProspectsLED Prospects photometric units

    E-Print Network [OSTI]

    Pulfrey, David L.

    Illuminated by: (a) high-CRI source (b) low-CRI source EFS #12;6 http://www.ecse.rpi.edu/~schubert/Light-Emitting-Diodes-dot-org/ #12;7 http://www.ecse.rpi.edu/~schubert/Light-Emitting-Diodes-dot-org/ #12;8 http://www.ecse.rpi.edu/~schubert/Light-Emitting-Diodes-dot-org/ #12;9 http://www.ecse.rpi.edu/~schubert/Light-Emitting-Diodes-dot-org/ #12;10 http://www.ecse.rpi.edu/~schubert/Light-Emitting-Diodes

  17. Jacob P. Brenner Design Specifications for Wet-Bulb Aspirator Apparatus

    E-Print Network [OSTI]

    Wisconsin at Madison, University of

    Jacob P. Brenner Thesis: Design Specifications for Wet-Bulb Aspirator Apparatus Project Description the concentration of water vapor in the air is the wet-bulb temperature. The wet-bulb temperature along with the dry-bulb for the testing of HVAC&R equipment. The focus of this research is on the accurate measurement of the wet-bulb

  18. Ammothermal Growth of Gan Substrates For Leds: High-Pressure Ammonothermal Process for Bulk Gallium Nitride Crystal Growth for Energy Efficient Commercially Competitive Lighting

    SciTech Connect (OSTI)

    None

    2011-01-01T23:59:59.000Z

    Broad Funding Opportunity Announcement Project: The new GaN crystal growth method is adapted from that used to grow quartz crystals, which are very inexpensive and represent the second-largest market for single crystals for electronic applications (after silicon). More extreme conditions are required to grow GaN crystals and therefore a new type of chemical growth chamber was invented that is suitable for large-scale manufacturing. A new process was developed that grows GaN crystals at a rate that is more than double that of current processes. The new technology will enable GaN substrates with best-in-world quality at lowest-in-world prices, which in turn will enable new generations of white LEDs, lasers for full-color displays, and high-performance power electronics.

  19. THE LUMINA PROJECT http://light.lbl.gov

    E-Print Network [OSTI]

    Jacobson, Arne

    components for the LED lights. #12;2 Introduction Solid-state lighting based on light emitting diode (LED

  20. Energy Efficiency and Conservation Block Grant Program

    Broader source: Energy.gov (indexed) [DOE]

    approximately 277 conventional60-watt light bulbs in tribal homes with 13-watt Light Emitting Diode (LED) bulbs; * Replacement of approximately 18 40-watt conventional fluorescent...

  1. CX-004575: Categorical Exclusion Determination | Department of...

    Broader source: Energy.gov (indexed) [DOE]

    approximately 277 conventional 60-watt light bulbs in tribal homes with 13-watt Light Emitting Diode (LED) bulbs; ? Replacement of approximately 18 40-watt conventional fluorescent...

  2. SuperBulbs Inc | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnualProperty Edit with formSoutheastern ILSunseeker Energy Holding AG JumpSunways AGSuperBulbs Inc

  3. Physiological properties and factors affecting migration of neural precursor cells in the adult olfactory bulb

    E-Print Network [OSTI]

    Darcy, Daniel Paul

    2007-01-01T23:59:59.000Z

    neurons in the olfactory bulb." J Neurosci 26(41): 10508-in the olfactory bulb." The Journal of comparative neurologycells to the olfactory bulb." J Neurosci 21(21): 8505-13.

  4. LED Essentials- Technology, Applications, Advantages, Disadvantages

    Broader source: Energy.gov [DOE]

    On October 11, 2007, Kevin Dowling, VP of Innovation for Philips Solid-State Lighting Solutions, presented a broad introduction to LED technology, and discussed the technology status, advantages...

  5. LED Color Stability: 10 Important Questions

    Broader source: Energy.gov [DOE]

    This April 15, 2014 webinar examined the causes of color shift, and took a look at existing metrics used to describe color shift/color stability in LED lighting. The lumen maintenance lifetime of...

  6. Solving the 'Green Gap' in LED Technology

    Broader source: Energy.gov [DOE]

    One long-standing high-priority research area for DOE is to increase the efficiency of deep green LEDs. Although most products today use phosphor conversion (PC) to produce white light from a blue LED, having a good green source could lead to color-mixed white sources that would avoid the losses associated with the PC approach.

  7. Embodied Energy and Off-Grid Lighting

    E-Print Network [OSTI]

    Alstone, Peter

    2012-01-01T23:59:59.000Z

    as a point of comparison with LED lighting product embodieda fairer comparison between off- grid LED lighting and other

  8. Modeling the wet bulb globe temperature using standard meteorological measurements.

    SciTech Connect (OSTI)

    Liljegren, J. C.; Carhart, R. A.; Lawday, P.; Tschopp, S.; Sharp, R.; Decision and Information Sciences

    2008-10-01T23:59:59.000Z

    The U.S. Army has a need for continuous, accurate estimates of the wet bulb globe temperature to protect soldiers and civilian workers from heat-related injuries, including those involved in the storage and destruction of aging chemical munitions at depots across the United States. At these depots, workers must don protective clothing that increases their risk of heat-related injury. Because of the difficulty in making continuous, accurate measurements of wet bulb globe temperature outdoors, the authors have developed a model of the wet bulb globe temperature that relies only on standard meteorological data available at each storage depot for input. The model is composed of separate submodels of the natural wet bulb and globe temperatures that are based on fundamental principles of heat and mass transfer, has no site-dependent parameters, and achieves an accuracy of better than 1 C based on comparisons with wet bulb globe temperature measurements at all depots.

  9. Building highly efficient LEDs in the yellow-green spectrum

    SciTech Connect (OSTI)

    None

    2012-01-01T23:59:59.000Z

    Argonne and Purdue researchers are peering deep into the atomic structure and composition of LED lights in order to build highly efficient LEDs in the yellow-green spectrum.

  10. Text-Alternative Version: Challenges in LED Research and Development

    Broader source: Energy.gov [DOE]

    Narrator: LEDs have made remarkable progress in the past decade and gained a strong foothold in the US marketplace. In 2012, LED lighting saved an estimated 71 trillion BTUs, equivalent to annual...

  11. Fabrication of InGaP LEDs on a graded buffer substrate

    E-Print Network [OSTI]

    Martínez, Josué F

    2007-01-01T23:59:59.000Z

    Introduction: Computer display panels create a vast color palette by combining color from three light emitting diodes (LEDs), each producing red, green, or blue light. The light from these three LEDs is chosen so that the ...

  12. A new maintenance friendly concept for bulb type generators

    SciTech Connect (OSTI)

    Scheidl, W.

    1998-07-01T23:59:59.000Z

    Bulb type generators in the rating range up to 15 MW are in a severe competition with geared up machines which operate at much higher speed and are therefore smaller and cheaper. Up to now the conventional bulb type generator in the standard design as it is used on several rivers in Austria and many other countries was not so economic in the lower rating range. A new and maintenance friendly concept for the bulb type generator design especially for these lower rating range ended in a more economic solution and is now able to compete with the geared up machines.

  13. Reducing home lighting expenses

    SciTech Connect (OSTI)

    Aimone, M.A.

    1981-02-01T23:59:59.000Z

    Ways to reduce lighting expenses are summarized. These include: turning off lights when not in use; keeping fixtures and lamps clean; replacing lamps with more efficient types; using three-way bulbs; use of daylighting; buying fewer lamps and reducing lamp wattage; consider repainting rooms; replacing recessed fixtures with tracklighting; and using efficient lamps for outdoor use. (MCW)

  14. A Second UV "Light Bulb" behind the SN 1006 Remnant

    E-Print Network [OSTI]

    Winkler, P F; Long, Knox S.

    1997-01-01T23:59:59.000Z

    A point X-ray source located 9 arcmin northeast of the center of SN~1006 has been spectroscopically identified as a background QSO, with a redshift of 0.335. The object is moderately bright, with magnitude V=18.3. If its ultraviolet spectrum is typical of low-z quasars, this object will be a second (after the Schweizer-Middleditch star) source to use for absorption spectroscopy of material within SN 1006. Absorption spectra provide a unique probe for unshocked ejecta within this supernova remnant, and can possibly solve the long-standing problem of "missing" iron in the remnants of Type Ia supernovae.

  15. A Second UV "Light Bulb" behind the SN 1006 Remnant

    E-Print Network [OSTI]

    P. Frank Winkler; Knox S. Long

    1997-07-22T23:59:59.000Z

    A point X-ray source located 9 arcmin northeast of the center of SN~1006 has been spectroscopically identified as a background QSO, with a redshift of 0.335. The object is moderately bright, with magnitude V=18.3. If its ultraviolet spectrum is typical of low-z quasars, this object will be a second (after the Schweizer-Middleditch star) source to use for absorption spectroscopy of material within SN 1006. Absorption spectra provide a unique probe for unshocked ejecta within this supernova remnant, and can possibly solve the long-standing problem of "missing" iron in the remnants of Type Ia supernovae.

  16. Westinghouse and Fuzhou Permitted to Restart Distribution of Light Bulb

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA group currentBradley Nickell DirectorThe&Management Alert WesternProducts |

  17. How Energy-Efficient Light Bulbs Compare with Traditional Incandescents |

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33Frequently20,000 RussianBy: Thomas P. D'Agostino,GlenLearningDepartmentDistributed

  18. The History of the Light Bulb | Department of Energy

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directed off Energy.gov. Are you sure you wantJoin us for|Idaho |EnergyTanklessThe CleanThe History ofThe

  19. The History of the Light Bulb | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the.pdfBreakingMayDepartmentTest for PumpingThe Facts on Gas Prices:TheTheHistory ofTheThe

  20. New GATEWAY Report Monitors LED System Performance in a High...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    the light. The Yuma site is an extreme environment: high ambient temperatures and direct solar radiation heat up the luminaires throughout the day, and at sunset the LED...

  1. LED Luminaire Lifetime: Recommendations for Testing and Reporting

    Broader source: Energy.gov (indexed) [DOE]

    product life, and many relied on the gradual lumen depreciation of the LED (light-emitting diode) source as the best indicator- resulting, on occasion, in unrealistic claims...

  2. The City of Los Angeles LED Streetlight Program

    Broader source: Energy.gov [DOE]

    View the video about the Los Angeles LED streetlight program, featuring an interview with City of Los Angeles Bureau of Street Lighting Director, Ed Ebrahimian.

  3. LEDs Go Ivy League: Princeton University and DOE GATEWAY Demonstrations

    Broader source: Energy.gov [DOE]

    View the video about LED lighting at Princeton University, which has dramatically reduced energy costs in a number of installations around campus. William Evans, electrical engineer, describes the...

  4. DOE Lighting Program Update: LED Validation Activities

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    savings equivalent to: - 190 terawatt (billion kilowatt) hours - Output of 24 1,000 MW power plants - 31.4 million metric tons of greenhouse gas emissions * Additional benefits...

  5. LED / Lighting Ultrafast Submicron Thermoreflectance Imaging

    E-Print Network [OSTI]

    duty cycles can be used to identify the current distribution profile before self-heating diameter copper vias in interconnects. Using electrical resistance measurements alone isn't enough

  6. Demonstration Assessment of LED Parking Structure Lighting

    Office of Scientific and Technical Information (OSTI)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItem Not Found Item Not Found The itemAIR57451 Clean Energy5655994DP-1513Assessment of

  7. Demonstration Assessment of LED Roadway Lighting

    Office of Scientific and Technical Information (OSTI)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItem Not Found Item Not Found The itemAIR57451 Clean

  8. Demonstration Assessment of LED Freezer Case Lighting

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny:Revised Finding of No53197 This

  9. Testimonials - Partnerships in LED Lighting - Philips Lumileds

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of ScienceandMesa del SolStrengthening a solidSynthesis of 2D AlloysTrailsANDDepartment of

  10. An LED pulser for measuring photomultiplier linearity

    E-Print Network [OSTI]

    Friend, M; Quinn, B

    2011-01-01T23:59:59.000Z

    A light-emitting diode (LED) pulser for testing the low-rate response of a photomultiplier tube (PMT) to scintillator-like pulses has been designed, developed, and implemented. This pulser is intended to simulate 80 ns full width at half maximum photon pulses over the dynamic range of the PMT, in order to precisely determine PMT linearity. This particular design has the advantage that, unlike many LED test rigs, it does not require the use of multiple calibrated LEDs, making it insensitive to LED gain drifts. Instead, a finite-difference measurement is made using two LEDs which need not be calibrated with respect to one another. These measurements give a better than 1% mapping of the response function, allowing for the testing and development of particularly linear PMT bases.

  11. LED MR16 Lamps

    Broader source: Energy.gov [DOE]

    The following CALiPER report provides detailed analysis of LED MR16 lamp performance, covering basic performance characteristics as well as subjective evaluation of beam, shadow, and color quality. Pending reports will offer analysis on performance attributes that are not captured by LM-79 testing. These reports are intended to educate the industry on market trends, potential issues, and important areas for improvement.

  12. Global LED Manufacturing

    Energy Savers [EERE]

    0.20.5W 5630 PPA 0.51.0W 7030 PCT XVGA HDMI UHD 4K2K UHD 8K4K 0.81.2W 3030 EMC 1.22.0W 3535 EMC w Flip-Chip 0.50.8W 2835 PCT ? 1.01.5 W ???? Revolution of LED...

  13. Sandia National Laboratories: LEDs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    News & Events, Photovoltaic, Research & Capabilities, Solar, Solid-State Lighting Titanium-dioxide (TiO2) nanoparticles show great promise as fillers to tune the refractive...

  14. Concord Municipal Light Plant- Commercial Energy Efficiency Rebate Program

    Broader source: Energy.gov [DOE]

    Concord Municipal Light Plant (CMLP) offers rebates to commercial customers for a variety of appliances, ETS heating systems, general lighting upgrades, CFL bulbs, and exit sign retrofit kits. A...

  15. MOF Coating a Promising Path to White LEDs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    (MOF); the structure was determined at Beamline 11.3.1. Coating a blue light-emitting diode (LED) with this compound readily generates white light with high luminous...

  16. LED Price Tracking Form

    Broader source: Energy.gov [DOE]

    DOE intends to update the SSL Pricing and Efficacy Trend Analysis for Utility Program Planning report on an annual basis, but doing so requires that we have sufficient product and purchase data including acquisition date, purchase price, product category, and rated initial lumens. Those interested in helping collect this data are asked to use the LED Price Tracking FormMicrosoft Excel and follow the instructions for submitting data.

  17. LED PAR38 Lamps

    Broader source: Energy.gov [DOE]

    The following CALiPER reports provide detailed analysis of LED PAR38 lamp performance, covering basic performance characteristics as well as subjective evaluation of beam, shadow, and color quality. Pending reports will offer analysis on flicker, dimming and power quality characteristics; stress testing; and lumen and chromaticity maintenance. These reports are intended to educate the industry on market trends, potential issues, and important areas for improvement.

  18. Expandable LED array interconnect

    DOE Patents [OSTI]

    Yuan, Thomas Cheng-Hsin; Keller, Bernd

    2011-03-01T23:59:59.000Z

    A light emitting device that can function as an array element in an expandable array of such devices. The light emitting device comprises a substrate that has a top surface and a plurality of edges. Input and output terminals are mounted to the top surface of the substrate. Both terminals comprise a plurality of contact pads disposed proximate to the edges of the substrate, allowing for easy access to both terminals from multiple edges of the substrate. A lighting element is mounted to the top surface of the substrate. The lighting element is connected between the input and output terminals. The contact pads provide multiple access points to the terminals which allow for greater flexibility in design when the devices are used as array elements in an expandable array.

  19. Arnold Schwarzenegger LIGHTING RESEARCH PROGRAM

    E-Print Network [OSTI]

    Project Summaries ELEMENT 2: ADVANCE LIGHTING TECHNOLOGIES PROJECT 2.1 LIGHT EMITTING DIODE (LED light emitting diodes (LED) technology for general lighting applications by developing a task lamp

  20. High efficiency incandescent lighting

    DOE Patents [OSTI]

    Bermel, Peter; Ilic, Ognjen; Chan, Walker R.; Musabeyoglu, Ahmet; Cukierman, Aviv Ruben; Harradon, Michael Robert; Celanovic, Ivan; Soljacic, Marin

    2014-09-02T23:59:59.000Z

    Incandescent lighting structure. The structure includes a thermal emitter that can, but does not have to, include a first photonic crystal on its surface to tailor thermal emission coupled to, in a high-view-factor geometry, a second photonic filter selected to reflect infrared radiation back to the emitter while passing visible light. This structure is highly efficient as compared to standard incandescent light bulbs.

  1. Radiation Dose-Volume Effects and the Penile Bulb

    SciTech Connect (OSTI)

    Roach, Mack, E-mail: mroach@radonc.ucsf.ed [Department of Radiation Oncology, University of California-San Francisco, San Francisco, CA (United States); Nam, Jiho [Department of Radiation Oncology, University of North Carolina at Chapel Hill, Chapel Hill, NC (United States); Gagliardi, Giovanna [Department of Medical Physics, Karolinska University Hospital and Karolinska Institutet, Stockholm (Sweden); El Naqa, Issam; Deasy, Joseph O. [Department of Radiation Oncology, School of Medicine, Washington University in St. Louis, St. Louis, MO (United States); Marks, Lawrence B. [Department of Radiation Oncology, University of North Carolina at Chapel Hill, Chapel Hill, NC (United States)

    2010-03-01T23:59:59.000Z

    The dose, volume, and clinical outcome data for penile bulb are reviewed for patients treated with external-beam radiotherapy. Most, but not all, studies find an association between impotence and dosimetric parameters (e.g., threshold doses) and clinical factors (e.g., age, comorbid diseases). According to the data available, it is prudent to keep the mean dose to 95% of the penile bulb volume to <50 Gy. It may also be prudent to limit the D70 and D90 to 70 Gy and 50 Gy, respectively, but coverage of the planning target volume should not be compromised. It is acknowledged that the penile bulb may not be the critical component of the erectile apparatus, but it seems to be a surrogate for yet to be determined structure(s) critical for erectile function for at least some techniques.

  2. Cree Sets New Benchmarks for LED Efficacy and Brightness

    Broader source: Energy.gov [DOE]

    Cree has successfully created a cool white LED prototype that delivers 107 lm/W at 350mA. This achievement builds on the Cree EZBright® LED chip platform, developed in part with prior funding support from DOE. Cree made the prototype LED under their DOE project focused on developing LED chips incorporating photonic crystal elements for improved light extraction and novel package technology for higher down-conversion efficiency compared to conventional LEDs. Based on a 1 millimeter-square chip, the new prototype LED produces white light with a CCT of 5500K and a CRI of 73. Integration of four of these prototype LEDs can produce luminous flux of more than 450 lumens.

  3. TESLA-FEL 2007-03 Application of low cost GaAs LED as neutron

    E-Print Network [OSTI]

    neutrons in unbiased Gallium Arsenide (GaAs) Light Emitting Diodes (LED) resulted in a reduction Keywords: COTS components, Displacement damage, Electron Linear Accelerator, GaAs Light emitting diode (LED) Gallium Arsenide (GaAs) light emitting diode (LED) for the assessment of integrated neutron fluence

  4. Modlisation des rythmes rapides bta et gamma du bulbe olfactif Nicolas Fourcaud-Trocm

    E-Print Network [OSTI]

    Boyer, Edmond

    Modélisation des rythmes rapides bêta et gamma du bulbe olfactif Nicolas Fourcaud-Trocmé Université mammifères, la première zone corticale traitant l'information olfactive est le bulbe olfactif (BO). Le codage anesthésié. MOTS-CLES bulbe olfactif, oscillations, bêta, gamma, modèle 1. Introduction En neurosciences, les

  5. Onion ipmPIPE -Diagnostic Pocket Series Bulb Growth Stages of Onion (Allium cepa L.)

    E-Print Network [OSTI]

    Pappu, Hanu R.

    Onion ipmPIPE - Diagnostic Pocket Series Bulb Growth Stages of Onion (Allium cepa L.) Fig 1 Fig 2 Fig 3 Fig 4 Fig 5 Fig 6 Fig 7 Fig 8 Allium Type: Fresh Market and Storage Onion Both pre- and post-bulb planting (seeds, transplants, sets). Pre-Bulb Growth Stages 1 ­ radical and flag leaf emergence (10-30 days

  6. Amlioration des plantes Production de bulbes in vitro et de novo

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Amélioration des plantes Production de bulbes in vitro et de novo à partir de tissus de tiges à bulbes, 29260 Ploudaniel; 2 Université Blaise Pascal, laboratoire de physiologie et génétique décembre 1992) Résumé — L'obtention de novo de bulbes in vitro est possible chez la tulipe dans un

  7. Behavioral/Systems/Cognitive Olfactory Bulb Gamma Oscillations Are Enhanced with

    E-Print Network [OSTI]

    Kopell, Nancy

    Behavioral/Systems/Cognitive Olfactory Bulb Gamma Oscillations Are Enhanced with Task Demands.However,thereisstillnodirectevidencethatsuchoscillationsareintrinsicallyalteredinintactsystems to aid in stimulus disambiguation. Here we show that gamma oscillatory power in the rat olfactory bulb; sensory acuity; beta oscillations; olfactory bulb; piriform (pyriform) Introduction The chemotopic

  8. Dendrodendritic Inhibition in the Olfactory Bulb Is Driven by NMDA Receptors

    E-Print Network [OSTI]

    Betz, William J.

    Dendrodendritic Inhibition in the Olfactory Bulb Is Driven by NMDA Receptors Nathan E. Schoppa,1 J synapses between mitral and granule cells in the rat olfactory bulb. In whole-cell patch-clamp recordings in bulb slices, stimulation of mitral cells elicited slowly decaying, GABAA receptor-mediated reciprocal

  9. ACTION DE L'ABLATION DES BULBES OLFACTIFS SUR LES MCANISMES DE LA REPRODUCTION

    E-Print Network [OSTI]

    Boyer, Edmond

    ACTION DE L'ABLATION DES BULBES OLFACTIFS SUR LES MÉCANISMES DE LA REPRODUCTION CHEZ LA TRUIE J. P Recheyches zoolechniques, Jouy-en-Josas (Seine et Oise). SOMMAIRE L'ablation chirurgicale des bulbes involution utérine. L'ablation totale des bulbes olfactifs semble donc perturber la décharge des hormones

  10. STABLE FREQUENCY RESPONSE TO VARYING STIMULUS INTENSITY IN A MODEL OF THE RAT OLFACTORY BULB

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    STABLE FREQUENCY RESPONSE TO VARYING STIMULUS INTENSITY IN A MODEL OF THE RAT OLFACTORY BULB Thomas Neurosciences et Systèmes sensoriels, CNRS UMR 5020, Lyon, France ABSTRACT In the rat olfactory bulb (OB), fast. Introduction The rat olfactory bulb (OB) is a rich and complex sensory processing system that shows stimulus

  11. Editorial Focus Fish Smell. Focus on "Odorant Specificity of Single Olfactory Bulb Neurons

    E-Print Network [OSTI]

    Stephens, Jacqueline

    Editorial Focus Fish Smell. Focus on "Odorant Specificity of Single Olfactory Bulb Neurons to Amino bulb, or antennal lobe. The precise nature of these odor features is yet to be determined for the most of this type in the fish, precise subclasses of olfactory bulb neurons for coding biologically significant

  12. Dendrodendritic Inhibition and Simulated Odor Responses in a Detailed Olfactory Bulb Network Model

    E-Print Network [OSTI]

    Feng, Jianfeng

    Dendrodendritic Inhibition and Simulated Odor Responses in a Detailed Olfactory Bulb Network Model responses in a detailed olfac- tory bulb network model. J Neurophysiol 90: 1921­1935, 2003. First published May 7, 2003; 10.1152/jn.00623.2002. In the olfactory bulb, both the spatial distribution

  13. Neuronal representation of odourants in the olfactory bulb of Xenopus laevis tadpoles

    E-Print Network [OSTI]

    Neuronal representation of odourants in the olfactory bulb of Xenopus laevis tadpoles Dirk Czesnik representation, olfactory bulb Abstract When an odourant enters the nose, olfactory receptor neurons (ORNs) convey information about it to the olfactory bulb (OB), where this information is processed and where

  14. Rhythm sequence through the olfactory bulb layers during the time window of a respiratory cycle

    E-Print Network [OSTI]

    Roux, Stephane

    Rhythm sequence through the olfactory bulb layers during the time window of a respiratory cycle 07, France Keywords: LFP, olfactory bulb, oscillations, rat, synchronization Abstract The mammalian olfactory bulb is characterized by prominent oscillatory activity of its local ®eld potentials. Breathing

  15. Structure of lateral inhibition in an olfactory bulb Andrew Davison, Jianfeng Feng, and David Brown

    E-Print Network [OSTI]

    Feng, Jianfeng

    Structure of lateral inhibition in an olfactory bulb model Andrew Davison, Jianfeng Feng, and David Abstract. It has been shown that mutual lateral inhibition of the projection neurones in the olfactory bulb, mediated by interneurones, serves to tune the representation of odours in the bulb and reduce the overlap

  16. THE EFFECT OF SNOWPACK WARMING ON THE STRESS BULB BELOW A SKIER Thomas Exner *

    E-Print Network [OSTI]

    Jamieson, Bruce

    THE EFFECT OF SNOWPACK WARMING ON THE STRESS BULB BELOW A SKIER Thomas Exner * Dept. of Geoscience exist to quantify or validate the temperature effect on the stress bulb below a skier. In this study we periods. Increasing temperatures of the near-surface layers altered the shape of the stress bulb, but so

  17. Linear programming applied to the ower sector: a Gladiolus bulb production case study

    E-Print Network [OSTI]

    Dragoti-Çela, Eranda

    Linear programming applied to the ¯ower sector: a Gladiolus bulb production case study Jose representative Brazilian bulb growing and trading company's decision making process, during the Gladiolus production planning activity. The pertinent LP model was focused on client's bulb requests to be attended

  18. Photoperiod Mediated Changes in Olfactory Bulb Neurogenesis and Olfactory Behavior in Male White-

    E-Print Network [OSTI]

    Nelson, Randy J.

    Photoperiod Mediated Changes in Olfactory Bulb Neurogenesis and Olfactory Behavior in Male White to long day lengths (LD) and short day lengths (SD) for 10 to 15 weeks and then examined olfactory bulb cell proliferation and survival using the thymidine analog BrdU, olfactory bulb granule cell morphology

  19. fMRI visualisation of transient activations in the rat olfactory bulb using short odour stimulations

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    fMRI visualisation of transient activations in the rat olfactory bulb using short odour in the olfactory bulb OB displays both spatial and temporal organization. The difficulty when assessing spatio of the olfactory bulb (OB). Hence, in this structure, the identity of odorants is associated with a unique spatial

  20. Calcium Influx through NMDA Receptors Directly Evokes GABA Release in Olfactory Bulb Granule Cells

    E-Print Network [OSTI]

    Strowbridge, Ben

    Calcium Influx through NMDA Receptors Directly Evokes GABA Release in Olfactory Bulb Granule Cells, Case Western Reserve University, Cleveland, Ohio 44106-4975 Recurrent inhibition in olfactory bulb on the activation of NMDA receptors. Using whole-cell recordings from rat olfactory bulb slices, we now show

  1. Solid state lighting component

    DOE Patents [OSTI]

    Yuan, Thomas; Keller, Bernd; Ibbetson, James; Tarsa, Eric; Negley, Gerald

    2010-10-26T23:59:59.000Z

    An LED component comprising an array of LED chips mounted on a planar surface of a submount with the LED chips capable of emitting light in response to an electrical signal. The LED chips comprise respective groups emitting at different colors of light, with each of the groups interconnected in a series circuit. A lens is included over the LED chips. Other embodiments can comprise thermal spreading structures included integral to the submount and arranged to dissipate heat from the LED chips.

  2. Solid state lighting component

    DOE Patents [OSTI]

    Keller, Bernd; Ibbetson, James; Tarsa, Eric; Negley, Gerald; Yuan, Thomas

    2012-07-10T23:59:59.000Z

    An LED component comprising an array of LED chips mounted on a planar surface of a submount with the LED chips capable of emitting light in response to an electrical signal. The LED chips comprise respective groups emitting at different colors of light, with each of the groups interconnected in a series circuit. A lens is included over the LED chips. Other embodiments can comprise thermal spreading structures included integral to the submount and arranged to dissipate heat from the LED chips.

  3. Commercial Lighting and LED Lighting Incentives | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742Energy China U.S. DepartmentEnergy This partAs the DepartmentSchools Institutional Savings

  4. Demonstration Assessment of Light Emitting Diode (LED) Street Lighting,

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny:Revised Finding of No53197 ThisFinal Report | Department of Energy

  5. LED Chips and Packaging for 120 LPW SSL Component

    SciTech Connect (OSTI)

    James Ibbetson

    2009-09-30T23:59:59.000Z

    Cree has developed a new, high-efficiency, low-cost, light emitting diode (LED) lamp module that should be capable of replacing standard, halogen, fluorescent and metal halide lamps based on the total cost of ownership. White LEDs are produced by combining one or more saturated color LEDs with a phosphor or other light down-converting media to achieve white broad-band illumination. This two year project addressed LED chip and package efficiency improvements to establish a technology platform suitable for low-cost, high-efficiency commercial luminaires. Novel photonic-crystal LEDs were developed to improve the light extraction efficiency of blue GaN-based LEDs compared to the baseline technology. Improved packaging designs that reduced down-conversion and absorption related light losses, led to a higher overall LED efficiency. Specifically, blue LEDs were demonstrated with light output nearing 600 mW and an external quantum efficiency greater than 60 percent (using 1 mm2 chips at an operating current of 350 mA). The results were achieved using a novel, production capable photonic-crystal LED fabrication process. These LEDs formed the basis for a multi-chip white lamp module prototype, which provided 510 lumens light output at a correlated color temperature (CCT) of 3875 K and an operating current of 350 mA per 1mm2 chip. The overall conversion efficiency at 4100 K improved to ~ 65%. The resulting efficacy is 112 lumens per watt (LPW) â?? a 33% improvement over the start of the project. In addition, a proof-of-concept luminaire was demonstrated that provided a flux of 1700 lumens at a 3842 K CCT.

  6. An Brief Overview Of Using LEDs In Lab

    E-Print Network [OSTI]

    Baas, Bevan

    Diodes · A Light-Emitting Diode (LED) is a special type of diode that emits photons (light) when current ­ Forward biased Diode Operation 0 V 5 V Current ~0 high (too high)5 V 0 V I anode cathode #12;3 Light-Emitting

  7. New Lighting Fixtures: Combining Creativity and Style with Energy Efficiency

    SciTech Connect (OSTI)

    Gordon, Kelly L.; Foster, Rebecca; McGowan, Terry

    2004-10-01T23:59:59.000Z

    This article for a building trade magazine describes a national design competition for energy efficient lighting sponsored by the U.S. Department of Energy, the American Lighting Association, and the Consortium for Energy Efficiency, with winners announced at ALA's Annual Conference May 14, 2004, in Tucson. The Lighting for Tomorrow competition was the first national lighting fixture design competition focusing on energy-efficient residential lighting. The competition invited fixture manufacturers and designers to come up with beautiful, functional lighting fixtures that also happen to be energy efficient. Fixtures were required to use a ''dedicated'' energy-efficient light source, such as a pin-based fluorescent lamp that cannot be replaced with a screw-in incandescent bulb. Fixtures also had to meet a minimum energy efficiency level that eliminated use of incandescent and halogen lamps, leaving the door open only to fluorescent sources and LEDs. More than 150 paper designs were submitted in the first phase of the competition, in 2003. Of those, 24 finalists were invited to submit working prototypes in 2004, and the winners were announced in May. The Grand Prize of $10,000 went to American Fluorescent of Waukegan, Illinois, for its ''Salem'' chandelier. Some winning fixtures are already available through Lowe's Home Improvement Centers.

  8. Phosphors for LED lamps

    DOE Patents [OSTI]

    Murphy, James Edward; Manepalli, Satya Kishore; Kumar, Prasanth Nammalwar

    2013-08-13T23:59:59.000Z

    A phosphor, a phosphor blend including the phosphor, a phosphor prepared by a process, and a lighting apparatus including the phosphor blend are disclosed. The phosphor has the formula (Ca.sub.1-p-qCe.sub.pK.sub.q).sub.xSc.sub.y(Si.sub.1-rGa.sub.r).sub.zO.su- b.12+.delta. or derived from a process followed using disclosed amounts of reactants. In the formula, (0

  9. Influence du poids et de la densit de plantation des bulbes d'chalote sur les caractristiques de

    E-Print Network [OSTI]

    Boyer, Edmond

    Influence du poids et de la densité de plantation des bulbes d'échalote sur les caractéristiques de la récolte et la prolificité des bulbes-fils Joseph COHAT Corentin TROMEUR LN.R.A., Station damélioration de la Pomme de terre et des Plantes à bulbes, F 29207 Landerneau RÉSUMÉ Des bulbes d'échalote de

  10. Influence d'un trempage des bulbes dans une solution d'acide 2-chloro thylphosphonique (thphon) sur la

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Influence d'un trempage des bulbes dans une solution d'acide 2-chloro éthylphosphonique (éthéphon la Pomme de terre et des Plantes à bulbes, F 29207 Landerneau RÉSUMÉ Le trempage des bulbes d augmentation du pourcentage de floraison. Ceci résulte d'une diminution du nombre de bulbes qui Ethéphon

  11. Electrodeless lighting RF power source development. Final report

    SciTech Connect (OSTI)

    NONE

    1996-08-30T23:59:59.000Z

    An efficient, solid state RF power source has been developed on this NICE project for exciting low power electrodeless lamp bulbs. This project takes full advantage of concurrent advances in electrodeless lamp technology. Electrodeless lamp lighting systems utilizing the sulfur based bulb type developed by Fusion Lighting, Inc., is an emerging technology which is based on generating light in a confined plasma created and sustained by RF excitation. The bulb for such a lamp is filled with a particular element and inert gas at low pressure when cold. RF power from the RF source creates a plasma within the bulb which reaches temperatures approaching those of high pressure discharge lamp plasmas. At these temperatures the plasma radiates substantial visible light with a spectrum similar to sunlight.

  12. EnergyUnited- Commercial Energy Efficient Lighting Rebate Program

    Broader source: Energy.gov [DOE]

    Commercial and industrial members who upgrade to energy-efficient light bulbs which meet EnergyUnited's standards are eligible for a prescriptive, "per unit" rebate. The cooperative will provide a...

  13. TRUE COLORS: LEDS AND THE RELATIONSHIP BETWEEN CCT, CRI, OPTICAL SAFETY, MATERIAL DEGRADATION, AND PHOTOBIOLOGICAL STIMULATION

    SciTech Connect (OSTI)

    Royer, Michael P.

    2014-08-30T23:59:59.000Z

    This document analyzes the optical, material, and photobiological hazards of LED light sources compared to conventional light sources. It documents that LEDs generally produce the same amount of blue light, which is the primary contributor to the risks, as other sources at the same CCT. Duv may have some effect on the amount of blue light, but CRI does not.

  14. Sandia National Laboratories: AlGaAs LEDs

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    electroluminescence was first reported by H.J. Round in 1907, and the first light-emitting diode (LED) was reported by O.V. Losev in 1927. Not until the birth of semiconductor...

  15. Laboratory Evaluation of LED T8 Replacement Lamp Products

    SciTech Connect (OSTI)

    Richman, Eric E.; Kinzey, Bruce R.; Miller, Naomi J.

    2011-05-23T23:59:59.000Z

    A report on a lab setting analysis involving LED lamps intended to directly replace T8 fluorescent lamps (4') showing light output, power, and economic comparisons with other fluorescent options.

  16. af led lyskilder: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Effective Fabrication of a Solar PV Panel for LED Lighting CiteSeer Summary: Abstract Solar cells are very fragile so they need a encapsulant and encasing for protection and...

  17. Semiconductors 4-bit I2C LED dimmer

    E-Print Network [OSTI]

    Berns, Hans-Gerd

    with SMBus · Internal power-on reset · Noise filter on SCL/SDA inputs · 4 open drain outputs directly drive for dimming LEDs in 256 discrete steps for Red/Green/Blue (RGB) color mixing and back light applications to 1.69 second. The open drain outputs directly drive the LEDs with maximum output sink current of 25 m

  18. CX-004962: Categorical Exclusion Determination | Department of...

    Broader source: Energy.gov (indexed) [DOE]

    halide light fixtures in the City Hall and Community Center parking lots with light-emitting diode (LED) light fixtures; and 3) replace incandescent light bulbs on traffic...

  19. Use Patterns of LED Flashlights in Kenya and a One-Year Cost Analysis of Flashlight Ownership

    SciTech Connect (OSTI)

    Tracy, Jennifer; Jacobson, Arne; Mills, Evan

    2010-02-16T23:59:59.000Z

    Flashlight usage is widespread across much of sub-Saharan Africa.1 In Kenya in particular, over half of all households report owning a flashlight (Kamfor, 2002). Aside from household use, flashlights are also widely used to perform income-earning jobs in Kenya. Lumina Research Note No.4, the first report in this series documenting flashlight use in Kenya, highlights flashlight use patterns of night watchmen and bicycle taxi drivers. Both of these are occupations that rely on the use of flashlights on a nightly basis (Tracy et al., 2009). Also highlighted by Research Note No.4, flashlight users in Kenya have reported being highly dissatisfied with the quality of the low-cost LED flashlights that are available, and they identify several reoccurring problems they have faced as flashlight end-users (Tracy et al., 2009). The fact that there exists a substantial dependency upon flashlights in Kenya and that users are disgruntled with the available products suggests reasons for concern about flashlight quality. This concern is present despite two recent technological transitions in the flashlight market. First, LED technology has quickly emerged as the dominant source of portable lighting in Kenya, outpacing incandescent flashlights (Johnstone et al., 2009). LED technology has the potential to provide efficiency and performance benefits relative to incandescent bulbs, and low-cost LEDs have achieved price levels that make them cost competitive with conventional lighting sources for a number of applications (Mills, 2005). Second, rechargeable sealed-lead acid (SLA) batteries are also becoming more prevalent alternatives to disposable dry cell batteries. Flashlights using rechargeable SLA batteries tend to have a lower total cost of ownership over a two-year period than a flashlight using dry cell batteries (Radecsky, 2009); however, as this current report highlights, this may vary depending on the intensity of use patterns. To avoid a potential market spoiling effect for off-grid lighting products based on LED technology (Mills and Jacobson, 2008; Lighting Africa, 2007) a better understanding of flashlight use-patterns is crucial (Tracy et al., 2009). In addition, the economic implications faced by rural flashlight end-users provide further incentive for a move toward higher quality low-cost flashlights. In this report, our team uses interviews with 46 end users of flashlights to collect information about their use patterns and costs associated with owning and operating flashlight products. While flashlights used in their portable mode typically do not represent a substitute for kerosene or other forms of fuel-based lighting, at times they are used in stationary applications in place of a fuel-based lamp. In either case, these products often represent end users first exposure to LED technology and rechargeable dry cell batteries, and thus stand to either provide a positive or negative impression of these technologies for a diversity of lighting applications.

  20. The Evolution of LED Packaging

    E-Print Network [OSTI]

    Linhardt, Robert J.

    better ­ Socket Saturation??? · Solid State Lighting Markets changing ­ Commoditization ­ Vertical the Lighting Space ­ An LCD TV Back Light Unit is a lot like a Fluorescent Lighting Fixture ©2012 Rensselaer overheat encapsulant) · Need to worry about "body color" (color in off state is a lighting design concern

  1. Quality and Performance of LED Flashlights in Kenya: Common End User Preferences and Complaints

    E-Print Network [OSTI]

    Tracy, Jenny

    2010-01-01T23:59:59.000Z

    at ensure the success of the off-grid lighting market. Theand E. Mills. 2008. "Measured Off? Grid LED Lighting Systemtechnology into the broader off-grid lighting market. The

  2. Estimating Wet Bulb Globe Temperature Using Standard Meteorological Measurements

    SciTech Connect (OSTI)

    Hunter, C.H.

    1999-11-18T23:59:59.000Z

    The heat stress management program at the Department of Energy''s Savannah River Site (SRS) requires implementation of protective controls on outdoor work based on observed values of wet bulb globe temperature (WBGT). To ensure continued compliance with heat stress program requirements, a computer algorithm was developed which calculates an estimate of WBGT using standard meteorological measurements. In addition, scripts were developed to generate a calculation every 15 minutes and post the results to an Intranet web site.

  3. anticorrelation light yield: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    for Light Engineering Websites Summary: Smart lighting: New Roles for Light in the Solid State Lighting World Robert F. Karlicek, Jr as the largest supplier of LED Lighting...

  4. Low-Cost Illumination-Grade LEDs

    SciTech Connect (OSTI)

    Epler, John

    2013-08-31T23:59:59.000Z

    Solid State Lighting is a cost-effective, energy-conserving technology serving a rapidly expand- ing multi-billion dollar market. This program was designed to accelerate this lighting revolution by reducing the manufacturing cost of Illumination-Grade LEDs. The technical strategy was to investigate growth substrate alternatives to standard planar sapphire, select the most effective and compatible option, and demonstrate a significant increase in Lumen/$ with a marketable LED. The most obvious alternate substrate, silicon, was extensively studied in the first two years of the program. The superior thermal and mechanical properties of Si were expected to improve wavelength uniformity and hence color yield in the manufacture of high-power illumination- grade LEDs. However, improvements in efficiency and epitaxy uniformity on standard c-plane sapphire diminished the advantages of switching to Si. Furthermore, the cost of sapphire decreased significantly and the cost of processing Si devices using our thin film process was higher than expected. We concluded that GaN on Si was a viable technology but not a practical option for Philips Lumileds. Therefore in 2012 and 2013, we sought and received amendments which broadened the scope to include other substrates and extended the time of execution. Proprietary engineered substrates, off-axis (non-c-plane) sapphire, and c-plane patterned sapphire substrates (PSS) were all investigated in the final 18 months of this program. Excellent epitaxy quality was achieved on all three candidates; however we eliminated engineered substrates and non-c-plane sapphire because of their higher combined cost of substrate, device fabrication and packaging. Ultimately, by fabricating a flip-chip (FC) LED based upon c-plane PSS we attained a 42% reduction in LED manufacturing cost relative to our LUXEON Rebel product (Q1-2012). Combined with a flux gain from 85 to 102 Lm, the LUXEON Q delivered a 210% increase in Lm/$ over this time period. The technology was commercialized in our LUXEON Q product in Sept., 2013. Also, the retention of the sapphire increased the robustness of the device, enabling sales of low-cost submount-free chips to lighting manufacturers. Thus, blue LED die sales were initiated in the form of a PSS-FC in February, 2013.

  5. LED structure with enhanced mirror reflectivity

    DOE Patents [OSTI]

    Bergmann, Michael; Donofrio, Matthew; Heikman, Sten; Schneider, Kevin S; Haberern, Kevin W; Edmond, John A

    2014-04-01T23:59:59.000Z

    Embodiments of the present invention are generally related to LED chips having improved overall emission by reducing the light-absorbing effects of barrier layers adjacent mirror contacts. In one embodiment, a LED chip comprises one or more LEDs, with each LED having an active region, a first contact under the active region having a highly reflective mirror, and a barrier layer adjacent the mirror. The barrier layer is smaller than the mirror such that it does not extend beyond the periphery of the mirror. In another possible embodiment, an insulator is further provided, with the insulator adjacent the barrier layer and adjacent portions of the mirror not contacted by the active region or by the barrier layer. In yet another embodiment, a second contact is provided on the active region. In a further embodiment, the barrier layer is smaller than the mirror such that the periphery of the mirror is at least 40% free of the barrier layer, and the second contact is below the first contact and accessible from the bottom of the chip.

  6. Product Quality Assurance for Off-Grid Lighting in Africa

    SciTech Connect (OSTI)

    World Bank; Mills, Evan; Mills, Evan

    2008-07-13T23:59:59.000Z

    Although the emergence of markets for high efficiency off-grid lighting technologies holds promise, realizing the potential of this opportunity on a long-term, sustainable basis requires careful attention to issues of product quality, consumer protection, and the potential for significant 'market spoiling', in anticipation of increases of sales of low cost, low performance off-grid lighting products. The goal of the Lighting Africa quality assurance workshop was to articulate strategies to mitigate the dangers of market spoiling and to explore ways to protect consumers from misleading advertising for sales of inferior, off-grid lighting products in the context of Lighting Africa's overarching objective to support the industry in developing a robust off-grid lighting market in Africa. The workshop resulted in the identification of two strategic approaches for meeting Lighting Africa quality assurance programmatic needs. The first strategy is intended to meet a short-term programmatic need for quality associated with requests for lighting products by bulk procurement agents, such as in a World Bank-financed project. The development of procurement specifications and test procedures that could be used in a quality/usability screening method in order to provide guidance for forthcoming large volume purchases emerged as the best solution to meet this need. Such approaches are used in World Bank-financed solar home systems (SHSs) projects in Bangladesh, Sri Lanka, and China, among others. However, unlike the SHSs which have multiple balance-of-system (BOS) components warranting the need for an array of specifications for individual components, stand alone lighting systems require specifications that are amenable to individual light points. To test this approach, Lighting Africa elected to use the technical specifications issued by the Photovoltaic Global Approval Program for solar lanterns that use CFL bulbs (PVRS11A) as the basis of qualifying such products. A contract has been competitively awarded to the Global Approval Program for Photovoltaics (PV GAP) under the Lighting Africa Program to select and test ten solar lantern product models. Lantern selection will be determined based on a number of criteria, among them, the ability to provide a daily duty cycle of at least 3 hours of light, the number of days of autonomy of battery, the volume of sales (especially in Africa), and whether or not the manufacturing facility is ISO 9000 certified. Those that are confirmed as meeting the specifications may be eligible to receive a PVGAP quality seal. The work is being carried out in partnership with the Photovoltaic and Wind Quality Test Center in Beijing, China and TUV Rhineland in Koeln, Germany. As off-grid LED-based stand-alone lighting products is in a nascent stage of development compared to CFL-based lanterns, Lighting Africa will support the development of a 'Quality Screening' approach to selecting LED lighting, in order not to delay consumers benefiting from such advances. The screening methodology could be used by procurement agencies to qualify LED lighting products for bulk or programmatic procurements. The main elements of this work comprises of developing a procurement specification and test procedure for undertaking a 'quick' quality/usability screening to be used for procuring LED lights and to test up to 30 LED-based lights to screen products that meet the requirement. The second strategy is intended to meet a longer-term need associated with creating a self-sustaining product quality assurance program that will effectively protect the African consumer, prevent significant market spoiling, adapt with expected technological advancements over the long-term--in other words, give consumers the ability to detect quality products and the information needed to find products that meet their specific needs from among the myriad of lighting products that become available commercially. Workshop discussions and the discussions evolving from the workshop led the Lighting Africa team to opt for an approach similar to that of th

  7. Ongoing LED RD Challenges (LED droop still challenge)

    Energy Savers [EERE]

    and Nonpolar GaN Semi polar GaN SOLUTION New GaN Crystal Planes * Semipolar planes for blue, green and yellow LEDs A. Romanov et al. : J. Appl. Phys. 100 (2006) 023533. (1122)...

  8. An Investigation into the Perception of Color under LED White Composite Spectra with Modulated Color Rendering

    E-Print Network [OSTI]

    O'Reilly, Una-May

    emitting diodes, LEDs. We examined seven LED white composite spectra with different color rendering of a pilot study that evaluates the perceptual impact of modulation of color rendering using multi-chip light

  9. Design and Predictive Control of a Net Zero Energy Home

    E-Print Network [OSTI]

    Morelli, F.; Abbarno, N.; Boese, E.; Bullock, J.; Carter, B.; Edwards, R.; Lapite, O.; Mann, D.; Mulvihill, C.; Purcell, E.; Stein, M. IV; Rasmussen, B. P.

    2013-01-01T23:59:59.000Z

    the same amount of light as traditional incandescent bulbs with less energy. Incandescent bulbs are inherently inefficient as most of the energy they consume goes towards heat generation. Compact fluorescent (CFL) and light emitting diode (LED) bulbs... as heat [1]. Compact fluorescent lamps (CFLs) and Light Emitting Diodes (LEDs) were analyzed in comparison with incandescent lamps. To determine the most energy efficient bulb, energy consumption for each type of bulb is needed. To do this, the amount...

  10. Development of Diagnostic Rules for a Dry Bulb Economizer Mixed Air Loop

    E-Print Network [OSTI]

    Underwood, D.

    1990-01-01T23:59:59.000Z

    knowledge base for a two fan variable air volume (VAV) air handling unit. Rules for the mixed air loop with a dry bulb economizer are presented....

  11. Maintenance Practices for LED Streetlights

    Broader source: Energy.gov [DOE]

    This April 14, 2014 webinar answered important questions about the maintenance and reliability of LED streetlights, and how to take these issues into account when planning and preparing for a...

  12. Microwave-driven ultraviolet light sources

    SciTech Connect (OSTI)

    Manos, Dennis M. (Williamsburg, VA); Diggs, Jessie (Norfolk, VA); Ametepe, Joseph D. (Roanoke, VA)

    2002-01-29T23:59:59.000Z

    A microwave-driven ultraviolet (UV) light source is provided. The light source comprises an over-moded microwave cavity having at least one discharge bulb disposed within the microwave cavity. At least one magnetron probe is coupled directly to the microwave cavity.

  13. Lighting

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHigh SchoolIn12electron 9 5Let us countLighting Sign In About | Careers |

  14. Energy Efficiency Through Lighting Upgrades

    SciTech Connect (OSTI)

    Kara Berst; Maria Howeth

    2010-06-01T23:59:59.000Z

    Lighting upgrades including neon to LED, incandescent to CFL's and T-12 to T-8 and T-5's were completed through this grant. A total of 16 Chickasaw nation facilities decreased their carbon footprint because of these grant funds. Calculations used were based on comparing the energy usage from the previous year�¢����s average and the current energy usage. For facilities without a full year's set of energy bills, the month after installation was compared to the same month from the previous year. Overall, the effect the lighting change-outs had for the gaming centers and casinos far exceeded expectations. For the Madill Gaming Center; both an interior and exterior upgrade was performed which resulted in a 31% decrease in energy consumption. This same reduction was seen in every facility that participated in the grant. Just by simply changing out light bulbs to newer energy efficient equivalents, a decrease in energy usage can be achieved and this was validated by the return on investment seen at Chickasaw Nation facilities. Along with the technical project tasks were awareness sessions presented at Chickasaw Head Starts. The positive message of environmental stewardship was passed down to head start students and passed along to Chickasaw employees. Excitement was created in those that learned what they could do to help reduce their energy bills and many followed through and took the idea home. For a fairy low cost, the general public can also use this technique to lower their energy consumption both at home and at work. Although the idea behind the project was somewhat simple, true benefits have been gained through environmental awareness and reductions of energy costs.

  15. University of Winnipeg Department of Theatre and Film Safe Handling of Lighting Instruments Updated: 09/2010

    E-Print Network [OSTI]

    Martin, Jeff

    . - Depending on the facility you are working in wattages may vary. Replace bulbs only of the same type the pipe and lower or hand it down to a spotter. CHANGING LAMPS: - The light must be physically unplugged to change a bulb you must wait a minimum of 5 minutes after the lamp has been on and you must use gloves

  16. CX-000135: Categorical Exclusion Determination | Department of...

    Broader source: Energy.gov (indexed) [DOE]

    involve changing the Tribe's street lights from incandescent bulbs to LED (light-emitting diode) lighting fixtures. DOCUMENT(S) AVAILABLE FOR DOWNLOAD CX-000135.pdf More...

  17. Sandia Energy - (Lighting and) Solid-State Lighting: Science...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    on the third and upcoming revolution (illumination). Topics cover the basics of light-emitting diode (LED) operation; a 200-year history of lighting technology; the importance of...

  18. Sandia National Laboratories: (Lighting and) Solid-State Lighting...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    on the third and upcoming revolution (illumination). Topics cover the basics of light-emitting diode (LED) operation; a 200-year history of lighting technology; the importance of...

  19. LED lamp power management system and method

    DOE Patents [OSTI]

    Gaines, James; Clauberg, Bernd; Van Erp, Josephus A. M.

    2013-03-19T23:59:59.000Z

    An LED lamp power management system and method including an LED lamp having an LED controller 58; a plurality of LED channels 60 operably connected to the LED controller 58, each of the plurality of LED channels 60 having a channel switch 62 in series with at least one shunted LED circuit 83, the shunted LED circuit 83 having a shunt switch 68 in parallel with an LED source 80. The LED controller 58 reduces power loss in one of the channel switch 62 and the shunt switch 68 when LED lamp electronics power loss (P.sub.loss) exceeds an LED lamp electronics power loss limit (P.sub.lim); and each of the channel switches 62 receives a channel switch control signal 63 from the LED controller 58 and each of the shunt switches 68 receives a shunt switch control signal 69 from the LED controller 58.

  20. LED lamp color control system and method

    DOE Patents [OSTI]

    Gaines, James; Clauberg, Bernd; Van Erp, Josephus A.M.

    2013-02-05T23:59:59.000Z

    An LED lamp color control system and method including an LED lamp having an LED controller 58; and a plurality of LED channels 60 operably connected to the LED controller 58, each of the plurality of LED channels 60 having a channel switch 62 in series with at least one shunted LED circuit 83, the shunted LED circuit 83 having a shunt switch 68 in parallel with an LED source 80. The LED controller 58 determines whether the LED source 80 is in a feedback controllable range, stores measured optical flux for the LED source 80 when the LED source 80 is in the feedback controllable range, and bypasses storing the measured optical flux when the LED source 80 is not in the feedback controllable range.

  1. Metameric Modulation for Diffuse Visible Light Communications with Constant Ambient Lighting

    E-Print Network [OSTI]

    Little, Thomas

    untapped for wireless communications. Advancements in light emitting diode (LED) technology are making

  2. Californidfsdfsdfsdfa OMNI-DIRECTIONAL LED

    E-Print Network [OSTI]

    California at Davis, University of

    BY: Principal Investigator: Michael Siminovitch, Ph.D. Director of Engineering: Keith Graeber Project Manager: Nicole Graeber California Lighting Technology Center University of California, Davis 633 Pena

  3. Randolph EMC- Commercial and Industrial Efficient Lighting Rebate Program (North Carolina)

    Broader source: Energy.gov [DOE]

    Commercial and industrial members who upgrade to energy-efficient light bulbs which meet Randolph EMC's standards are eligible for a prescriptive incentive payment. The cooperative will provide a...

  4. Olfactory deprivation increases dopamine D2 receptor density in the rat olfactory bulb

    SciTech Connect (OSTI)

    Guthrie, K.M.; Pullara, J.M.; Marshall, J.F.; Leon, M. (University of California, Irvine (USA))

    1991-05-01T23:59:59.000Z

    Unilateral olfactory deprivation during postnatal development results in significant anatomical and neurochemical changes in the deprived olfactory bulb. Perhaps the most dramatic neurochemical change is the loss of dopaminergic expression by neurons of the glomerular region. The authors describe here the effects of early olfactory deprivation on other elements of the bulb dopaminergic system, namely the dopamine receptors of the olfactory bulb. Rat pups had a single naris occluded on postnatal day 2 (PN2). On PN20 or PN60, animals were sacrificed and the bulbs were examined for catecholamine levels or D2 and D1 dopamine receptor binding. Receptor densities were quantified by in vitro autoradiography using the tritiated antagonists spiperone (D2) and SCH23390 (D1). Dopamine uptake sites were similarly examined using tritiated mazindol. No significant specific labeling of D1 or mazindol sites was observed in the olfactory bulbs of control or experimental animals at either age. Normal animals displayed prominent labeling of D2 sites in the glomerular and nerve layers. After 60 days of deprivation, deprived bulbs exhibited an average increase in D2 receptor density of 32%. As determined by Scatchard analysis, the mean values for Kd and Bmax were 0.134 nM and 293 fmol/mg protein in normal bulbs, and 0.136 nM and 403 fmol/mg protein in deprived bulbs. The results suggest that, as in the neostriatum, dopamine depletion in the olfactory bulb leads to an upregulation of D2 receptor sites. This change may represent an attempt by the system to adapt neurochemically to reduced dopaminergic activity and thereby maintain bulb function.

  5. Influence des conditions de conservation des bulbes d'chalote (Allium cepa L. var. aggregatum) sur leur

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Influence des conditions de conservation des bulbes d'échalote (Allium cepa L. var. aggregatum) sur leur levée Joseph COHAT LN.R.A., Station d'Amélioration de la Pomme de terre & des Plantes à bulbes, F 29207 Landerneau RÉSUMÉ Les bulbes d'échalote de Jersey (type demi-longue) sont dormants au moment de la

  6. A Bit About Bulbs Night temperatures are cool, the air is almost crisp. The vegetable harvest is tapering

    E-Print Network [OSTI]

    New Hampshire, University of

    A Bit About Bulbs Night temperatures are cool, the air is almost crisp. The vegetable harvest! There is always something to do, and right now is the time to plant spring-flowering bulbs. Whether your preference is for naturalized or formal bulb plantings, on a small or large scale, keep kinds and colors

  7. Impairment of Neurogensis in the Olfactory Bulb of Transgenic Mice Overexpressing Human Wildtype Alpha Synuclein Under the Thy-1 Promoter

    E-Print Network [OSTI]

    Allman, John M.

    Impairment of Neurogensis in the Olfactory Bulb of Transgenic Mice Overexpressing Human Wildtype, cortex and olfactory bulb (Rockenstein et al., 2002). These mice demonstrate early and progressive motor by olfactory ensheathing glia, and eventually reach the olfactory bulb (Gritti et al., 2002). Recent studies

  8. Dynamical Mechanisms of Odor Processing in Olfactory Bulb Mitral Cells Daniel B. Rubin and Thomas A. Cleland

    E-Print Network [OSTI]

    Cleland, Thomas A.

    Dynamical Mechanisms of Odor Processing in Olfactory Bulb Mitral Cells Daniel B. Rubin and Thomas A- nisms of odor processing in olfactory bulb mitral cells. J Neuro- physiol 96: 555­568, 2006. First, conductance-based compartmental model of olfactory bulb mitral cells that exhibits the complex dynamical

  9. Stability of fast oscillations in mammalian olfactory bulb: experiment and modeling Nicolas Fourcaud-Trocmea,b,c,d,

    E-Print Network [OSTI]

    Voegtlin, Thomas

    Stability of fast oscillations in mammalian olfactory bulb: experiment and modeling Nicolas Cortex, Vandoeuvre-les-Nancy, F-54506, France Abstract In the rat olfactory bulb (OB), fast oscillations observed stability of the oscillatory regimes. Keywords: olfactory bulb, beta oscillations, gamma

  10. Odor vapor pressure and quality modulate local field potential oscillatory patterns in the olfactory bulb of the

    E-Print Network [OSTI]

    Roux, Stephane

    in the olfactory bulb of the anesthetized rat Tristan Cenier,1 Corine Amat,1 Philippe Litaudon,1 Samuel Garcia,1 potentials, molecular features, olfactory bulb, oscillations, respiratory cycle Abstract A central question-temporal pattern of activation in the olfactory bulb (OB), in both glomerular and mitral cell layers. Mitral

  11. Scaling Up: Kilolumen Solid-State Lighting Exceeding 100 LPW via Remote Phosphor

    SciTech Connect (OSTI)

    Waqidi Falicoff

    2008-09-15T23:59:59.000Z

    This thirty-month project was successful in attaining its ambitious objectives of demonstrating a radically novel 'remote-phosphor' LED light source that can out-perform conventional conformal coated phosphor LED sources. Numerous technical challenges were met with innovative techniques and optical configurations. This product development program for a new generation of solid-state light sources has attained unprecedented luminosity (over 1 kilo-lumen) and efficacy (based on the criterion lumens per 100mw radiant blue). LPI has successfully demonstrated its proprietary technology for optical synthesis of large uniform sources out of the light output of an array of separated LEDs. Numerous multiple blue LEDs illuminate single a phosphor patch. By separating the LEDs from the phosphor, the phosphor and LEDs operate cooler and with higher efficiency over a wide range of operating conditions (from startup to steady state). Other benefits of the system include: better source uniformity, more types of phosphor can be used (chemical interaction and high temperatures are no longer an issue), and the phosphor can be made up from a pre-manufactured sheet (thereby lowering cost and complexity of phosphor deposition). Several laboratory prototypes were built and operated at the expected high performance level. The project fully explored two types of remote phosphor system: transmissive and reflective. The first was found to be well suited for a replacement for A19 type incandescent bulbs, as it was able to replicate the beam pattern of a traditional filament bulb. The second type has the advantages that it is pre-collimate source that has an adjustable color temperature. The project was divided in two phases: Phase I explored a transmissive design and Phase II of the project developed reflective architectures. Additionally, in Phase II the design of a spherical emitting transmissive remote phosphor bulb was developed that is suitable for replacement of A19 and similar light bulbs. In Phase II several new reflective remote phosphor systems were developed and patents applied for. This research included the development of reflective systems in which the short-pass filter operated at a nominal incidence angle of 15{sup o}, a major advancement of this technology. Another goal of the project was to show that it is possible to align multiple optics to multiple LEDs (spaced apart for better thermal management) to within an accuracy in the z-direction of 10 microns or less. This goal was achieved. A further goal was to show it is possible to combine and homogenize the output from multiple LEDs without any flux loss or significant increase in etendue. This goal also was achieved. The following color-coded computer drawing of the Phase 2 reflective remote phosphor prototype gives an idea of the accuracy challenges encountered in such an assembly. The actual setup has less functional clarity due to the numerous items of auxiliary equipment involved. Not only did 10 degrees of freedoms alignment have to be supplied to the LEDs and component prisms as well, but there were also micro-titrating glue dispensers and vacuum hoses. The project also utilized a recently introduced high-index glass, available in small customized prisms. This prototype also embodies a significant advance in thin-film design, by which an unprecedented 98% single-pass efficiency was attained over a 30 degree range of incidence angle (Patents Pending). Such high efficiency is especially important since it applies to the blue light going to the phosphor and then again to the phosphor's light, so that the 'system' efficiency associated with short-pass filter was 95.5%. Other losses have to be kept equally small, towards which a new type of ultra-clear injection-moldable acrylic was discovered and used to make ultra-transparent CPC optics. Several transmissive remote phosphor prototypes were manufactured that could replace screw-in type incandescent bulbs. The CRI of the white light from these prototypes varied from 55 to 93. The system efficiency achieved was between 27 to 29.5

  12. LED Luminaire Lifetime: Recommendations For Testing and Reporting |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(FactDepartment ofLetter Report:40PM toLED Lighting Facts LED Lighting

  13. LED Performance Specification Series: T8 Replacement Lamps

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(FactDepartment ofLetter Report:40PM toLED Lighting Facts LED LightingOutdoor

  14. LED T8 Replacement Lamps | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(FactDepartment ofLetter Report:40PM toLED Lighting Facts LED LightingOutdoorLEDT8

  15. Low Cost Lithography Tool for High Brightness LED Manufacturing

    SciTech Connect (OSTI)

    Andrew Hawryluk; Emily True

    2012-06-30T23:59:59.000Z

    The objective of this activity was to address the need for improved manufacturing tools for LEDs. Improvements include lower cost (both capital equipment cost reductions and cost-ofownership reductions), better automation and better yields. To meet the DOE objective of $1- 2/kilolumen, it will be necessary to develop these highly automated manufacturing tools. Lithography is used extensively in the fabrication of high-brightness LEDs, but the tools used to date are not scalable to high-volume manufacturing. This activity addressed the LED lithography process. During R&D and low volume manufacturing, most LED companies use contact-printers. However, several industries have shown that these printers are incompatible with high volume manufacturing and the LED industry needs to evolve to projection steppers. The need for projection lithography tools for LED manufacturing is identified in the Solid State Lighting Manufacturing Roadmap Draft, June 2009. The Roadmap states that Projection tools are needed by 2011. This work will modify a stepper, originally designed for semiconductor manufacturing, for use in LED manufacturing. This work addresses improvements to yield, material handling, automation and throughput for LED manufacturing while reducing the capital equipment cost.

  16. Issues, Models and Solutions for Triac Modulated Phase Dimming of LED Lamps

    E-Print Network [OSTI]

    Lehman, Brad

    Issues, Models and Solutions for Triac Modulated Phase Dimming of LED Lamps Dustin Rand (Raytheon Edison socket LED lamps directly from residential phase modulated dimmer switches. In order to explain brightness "White Light" LEDs have experts predicting that the "bright white replacement lamp" could trigger

  17. Task lights, commonly used in offices, homes, and dormitories, often use

    E-Print Network [OSTI]

    and posing difficulties in focusing the light. Light-emitting diode (LED) lighting, a fairly new solid

  18. LOW-COST LED LUMINAIRE FOR GENERAL ILLUMINATION

    SciTech Connect (OSTI)

    Lowes, Ted

    2014-07-31T23:59:59.000Z

    During this two-year Solid-State Lighting (SSL) Manufacturing R&D project Cree developed novel light emitting diode (LED) technologies contributing to a cost-optimized, efficient LED troffer luminaire platform emitting at ~3500K correlated color temperature (CCT) at a color rendering index (CRI) of >90. To successfully achieve program goals, Cree used a comprehensive approach to address cost reduction of the various optical, thermal and electrical subsystems in the luminaire without impacting performance. These developments built on Cree’s high- brightness, low-cost LED platforms to design a novel LED component architecture that will enable low-cost troffer luminaire designs with high total system efficacy. The project scope included cost reductions to nearly all major troffer subsystems as well as assembly costs. For example, no thermal management components were included in the troffer, owing to the optimized distribution of compact low- to mid-power LEDs. It is estimated that a significant manufacturing cost savings will result relative to Cree’s conventional troffers at the start of the project. A chief project accomplishment was the successful development of a new compact, high-efficacy LED component geometry with a broad far-field intensity distribution and even color point vs. emission angle. After further optimization and testing for production, the Cree XQ series of LEDs resulted. XQ LEDs are currently utilized in Cree’s AR series troffers, and they are being considered for use in other platforms. The XQ lens geometry influenced the independent development of Cree’s XB-E and XB-G high-voltage LEDs, which also have a broad intensity distribution at high efficacy, and are finding wide implementation in Cree’s omnidirectional A-lamps.

  19. Low Emission Development Strategies (LEDS): Technical, Institutional...

    Open Energy Info (EERE)

    Strategies (LEDS): Technical, Institutional and Policy Lessons Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Low Emission Development Strategies (LEDS): Technical,...

  20. The Problem Conventional office lighting typically consists of bright fluo-

    E-Print Network [OSTI]

    by delamping--result in lower power consump- tion. The PLS, which features light-emitting diode (LED lighting is reduced and three light-emitting diode (LED) task lights (two desk lamps and one undercabinet

  1. Solid-State Lighting

    Broader source: Energy.gov (indexed) [DOE]

    into the market. On the market side, DOE works closely with drivers, heat sinks, and optics. LEDs must be carefully energy efficiency program partners, lighting professionals,...

  2. Odor recognition and segmentation by coupled olfactory bulb and cortical networks

    E-Print Network [OSTI]

    Li, Z; Li, Zhaoping; Hertz, John

    1999-01-01T23:59:59.000Z

    We present a model of a coupled system of the olfactory bulb and cortex. Odor inputs to the epithelium are transformed to oscillatory bulbar activities. The cortex recognizes the odor by resonating to the bulbar oscillating pattern when the amplitude and phase patterns from the bulb match an odor memory stored in the intracortical synapses. We assume a cortical structure which transforms the odor information in the oscillatory pattern to a slow DC feedback signal to the bulb. This feedback suppresses the bulbar response to the pre-existing odor, allowing subsequent odor objects to be segmented out for recognition.

  3. Optical Wireless based on High Brightness Visible LEDs Grantham Pang, Thomas Kwan, Hugh Liu, Chi-Ho Chan

    E-Print Network [OSTI]

    Pang, Grantham

    and encoded with audio or data signal. Hence, an LED indicator lamp or traffic light can become an information for incandescent lamps [3,4]. This advancement has led to the production of large- area full-color LED displaysOptical Wireless based on High Brightness Visible LEDs Grantham Pang, Thomas Kwan, Hugh Liu, Chi

  4. WhiteOptics' Low-Cost Reflector Composite Boosts LED Fixture Efficiency

    Broader source: Energy.gov [DOE]

    With the help of DOE funding, WhiteOptics has developed a composite coating that can be used to improve efficiency in backlit, indirect, and cavity-mixing LED luminaire designs by maximizing light reflection and output. The highly diffuse coating, which is based on a novel high-reflectance particle technology, allows for uniform distribution of light without exaggerating the point-source nature of the LEDs, and is intended to offer an overall system cost-improving solution for LED optics.

  5. LACKEY, PAUL E. An Investigation of Bridge Deck Overhang Falsework Systems Installed onto Bulb Tee Girders. (Under the direction of Dr. Emmett Sumner.)

    E-Print Network [OSTI]

    Bulb Tee Girders. (Under the direction of Dr. Emmett Sumner.) Bulb Tee girders provide a practical moments of inertia to withstand the massive moments created in the spans. A bulb tee girder possesses the thin top flange of an exterior bulb tee girder in the bridge deck overhang falsework system to fail

  6. Philips' LED Luminaires Brighten the Rensselaer Engineering Fabrication & Prototyping Facility (also known as the Machine Shop)

    E-Print Network [OSTI]

    Linhardt, Robert J.

    . #12;To help bridge its research efforts with currently available solid state lighting technology outreach to increase campus and community awareness as to the benefits of solid state lighting. About Royal a donation of LED fixtures from Philips Lighting. The Smart Lighting Sustainability Club, comprised

  7. Feedback-Controlled LED Photobioreactor for Photophysiological Studies of Cyanobacteria

    SciTech Connect (OSTI)

    Melnicki, Matthew R.; Pinchuk, Grigoriy E.; Hill, Eric A.; Kucek, Leo A.; Stolyar, Sergey; Fredrickson, Jim K.; Konopka, Allan; Beliaev, Alex S.

    2013-04-09T23:59:59.000Z

    A custom photobioreactor (PBR) was designed to enable automatic light adjustments using computerized feedback control. A black anodized aluminum enclosure, constructed to surround the borosilicate reactor vessel, prevents the transmission of ambient light and serves as a mount for arrays of light-emitting diodes (LEDs). The high-output LEDs provide narrow-band light of either 630 or 680 nm for preferential excitation of the cyanobacterial light-harvesting pigments, phycobilin or chlorophyll a, respectively. Custom developed software BioLume provides automatic control of optical properties and a computer feedback loop can automatically adjust the incident irradiance as necessary to maintain a fixed transmitted light through the culture, based on user-determined set points. This feedback control serves to compensate for culture dynamics which have optical effects, (e.g., changing cell density, pigment adaptations) and thus can determine the appropriate light conditions for physiological comparisons or to cultivate light-sensitive strains, without prior analyses. The LED PBR may also be controlled as a turbidostat, using a feedback loop to continuously adjust the rate of media-dilution based on the transmitted light measurements, with a fast and precise response. This cultivation system gains further merit as a high-performance analytical device, using non-invasive tools (e.g., dissolved gas sensors, online mass spectrometry) to automate real-time measurements, thus permitting unsupervised experiments to search for optimal growth conditions, to monitor physiological responses to perturbations, as well as to quantitate photophysiological parameters using an in situ light-saturation response routine.

  8. Designing Interactive Lighting Dzmitry Aliakseyeu, Bernt Meerbeek, Jon

    E-Print Network [OSTI]

    The Light Emitting Diode (LED) has caused a profound change within the lighting industry. This is due

  9. Small Area Array-Based LED Luminaire Design

    SciTech Connect (OSTI)

    Thomas Yuan

    2008-01-09T23:59:59.000Z

    This report contains a summary of technical achievements during a three-year project to demonstrate high efficiency LED luminaire designs based on small area array-based gallium nitride diodes. Novel GaN-based LED array designs are described, specifically addressing the thermal, optical, electrical and mechanical requirements for the incorporation of such arrays into viable solid-state LED luminaires. This work resulted in the demonstration of an integrated luminaire prototype of 1000 lumens cool white light output with reflector shaped beams and efficacy of 89.4 lm/W at CCT of 6000oK and CRI of 73; and performance of 903 lumens warm white light output with reflector shaped beams and efficacy of 63.0 lm/W at CCT of 2800oK and CRI of 82. In addition, up to 1275 lumens cool white light output at 114.2 lm/W and 1156 lumens warm white light output at 76.5 lm/W were achieved if the reflector was not used. The success to integrate small area array-based LED designs and address thermal, optical, electrical and mechanical requirements was clearly achieved in these luminaire prototypes with outstanding performance and high efficiency.

  10. Visible Light Communications: Recent Activities in Japan

    E-Print Network [OSTI]

    Lü, James Jian-Qiang

    The Graduate School of System Design and Management, Keio University, Yokohama, Japan Smart Spaces: A Smart, visible light LEDs are beginning to be used in every home and office, which makes visible light LEDs ideal, and the market share of LED lighting will be more than 30 percent of total lighting market in 2016. Prediction

  11. A critical period for activity-dependent synaptic development during olfactory bulb adult neurogenesis

    E-Print Network [OSTI]

    Kelsch, Wolfgang

    New neurons integrate in large numbers into the mature olfactory bulb circuit throughout life. The factors controlling the synaptic development of adult-born neurons and their connectivity remain essentially unknown. We ...

  12. Adaptive Street Lighting Controls

    Broader source: Energy.gov [DOE]

    This two-part DOE Municipal Solid-State Street Lighting Consortium webinar focused on LED street lighting equipped with adaptive control components. In Part I, presenters Amy Olay of the City of...

  13. Sandia National Laboratories: Lighting

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Lighting Solid-State Lighting Science EFRC On November 11, 2010, in Welcome History of Incandescence History of LEDs Grand Challenges Our EFRC SSLS-EFRC Contacts News Publications...

  14. Program Name: Simple Steps, Smart Savings Simple Steps, Smart...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and install high-quality, energy-efficient compact fluorescent lamps (CFLs), light emitting diode bulbs (LEDs), light fixtures and energy-saving showerheads. Beginning in...

  15. U.S. Energy Information Administration (EIA) - Sector

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    of incandescent bulbs with more efficient compact fluorescent lighting and light-emitting diode (LED) lamps. Among electric end-use services in the residential sector,...

  16. 2.44a0005 Physiology of the Main Olfactory Bulb Matthew Ennis1

    E-Print Network [OSTI]

    Hayar, Abdallah

    -inhibition 27 2.44.6.4.2 Lateral inhibition 27 2.44.6.4.3 Role of Ca2þ influx through NMDA receptors and voltage.44.8 Neurophysiology of Primary Olfactory Cortical Inputs to Main Olfactory Bulb 29 2.44.9 Oscillations and Synchrony in Main Olfactory Bulb 29 2.44.9.1 Oscillations 29 2.44.9.1.1 Theta rhythm 30 2.44.9.1.2 Gamma rhythm 30 2

  17. Interrelationships between air velocity and natural wet-bulb thermometer response

    E-Print Network [OSTI]

    Jones, Nathan Glenn

    1983-01-01T23:59:59.000Z

    INTERRELATIONSHIPS BETWEEN AIR VFLOCITY ANO NATURAL WET-BULB THERMOMETER RESPONSE A Thesis by NATHAN GLENN JONES Submitted to the Graduate Colleqe of Texas ASM University i n partial fulfillment of the requirement for the degree of MASTER... OF SCIENCE AUGUST 1983 Major Subject: Industrial Hygiene INTERRELATIONSHIPS BETWEEN AIR VELOCITY AND NATURAL WET-BULB THERMOMETER RESPONSE A Thesis by NATHAN GLENN JONES Approved as to style an content by: airman o ommittee er Member ~~' A~ Member...

  18. Vision Research 41 (2001) 427439 Characterization and use of a digital light projector for vision

    E-Print Network [OSTI]

    Brainard, David H.

    2001-01-01T23:59:59.000Z

    . For example, a light emitting diode (LED)-based stimulator has many ideal characteristics. LEDs have high

  19. Many exterior entry and walkway lights in residential and commercial

    E-Print Network [OSTI]

    be difficult since retail stocking is inconsistent. The Light-Emitting Diode (LED) Hybrid Outdoor Fixture

  20. An LED-based Flasher System for VERITAS

    E-Print Network [OSTI]

    Hanna, D; McCutcheon, M; Nikkinen, L; 10.1016/j.nima.2009.10.107

    2009-01-01T23:59:59.000Z

    We describe a flasher system designed for use in monitoring the gains of the photomultiplier tubes used in the VERITAS gamma-ray telescopes. This system uses blue light-emitting diodes (LEDs) so it can be operated at much higher rates than a traditional laser-based system. Calibration information can be obtained with better statistical precision with reduced loss of observing time. The LEDs are also much less expensive than a laser. The design features of the new system are presented, along with measurements made with a prototype mounted on one of the VERITAS telescopes.

  1. LEDs Ready for Takeoff at Louisiana Airport | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(FactDepartment ofLetter Report:40PM toLED Lighting Facts LED

  2. Controls for Solid-State Lighting

    SciTech Connect (OSTI)

    Rubinstein, Francis

    2007-06-22T23:59:59.000Z

    This study predicts new hybrid lighting applications for LEDs. In hybrid lighting, LEDs provide a low-energy 'standby' light level while another, more powerful, efficient light source provides light for occupied periods. Lighting controls will allow the two light sources to work together through an appropriate control strategy, typically motion-sensing. There are no technical barriers preventing the use of low through high CRI LEDs for standby lighting in many interior and exterior applications today. The total luminous efficacy of LED systems could be raised by increasing the electrical efficiency of LED drivers to the maximum practically achievable level (94%). This would increase system luminous efficacy by 20-25%. The expected market volumes for many types of LEDs should justify the evolution of new LED drivers that use highly efficient ICs and reduce parts count by means of ASICs. Reducing their electronics parts count by offloading discrete components onto integrated circuits (IC) will allow manufacturers to reduce the cost of LED driver electronics. LED luminaire manufacturers will increasingly integrate the LED driver and thermal management directly in the LED fixture. LED luminaires of the future will likely have no need for separable lamp and ballast because the equipment life of all the LED luminaire components will all be about the same (50,000 hours). The controls and communications techniques used for communicating with conventional light sources, such as dimmable fluorescent lighting, are appropriate for LED illumination for energy management purposes. DALI has been used to control LED systems in new applications and the emerging ZigBee protocol could be used for LEDs as well. Major lighting companies are already moving in this direction. The most significant finding is that there is a significant opportunity to use LEDs today for standby lighting purposes. Conventional lighting systems can be made more efficient still by using LEDs to provide a low-energy standby state when lower light levels are acceptable.

  3. DOE Lighting Program Update: LED Validation Activities | Department...

    Energy Savers [EERE]

    & Requirements Reporting & Data Training Project Funding Products & Technologies Technical Assistance Institutional Change Awards Publications Case Studies Tools News Contact Us...

  4. New LED light sources and lamps for general illumination

    E-Print Network [OSTI]

    , Henrik Pedersen and Paul Michael Petersen Risø DTU, Optics and Plasma Research Department, DK-4000

  5. DOE Publishes GATEWAY Report on LED Lighting in a Performing...

    Broader source: Energy.gov (indexed) [DOE]

    video, is available on the GATEWAY Demonstration Indoor Projects webpage. Addthis Related Articles DOE Releases Report on SSL Adoption in Museums DOE Publishes CALiPER Report on...

  6. LED Lighting: Just the Facts, Please! | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    that it will adequately meet your needs. What it means is that you can have peace of mind when checking out the label-that the information listed is accurate. You still need to...

  7. Slideshow: Flipping the Switch on LED Lighting for the National...

    Broader source: Energy.gov (indexed) [DOE]

    President & CEO, OSRAM SYLVANIA - Eric Spiegel, President and Chief Executive Officer, Siemens Corporation & CEO, U.S. Region - Interior Department Secretary Ken Salazar - Joseph...

  8. Measured Off-Grid LED Lighting System Performance

    E-Print Network [OSTI]

    Granderson, Jessica

    2009-01-01T23:59:59.000Z

    beam candlepower, and luminance varied by 8x, 32x, and 61xMaximum beam candlepower Luminance (cd/m2) Daylight glarequality, luminous intensity, luminance, and glare. Note that

  9. LIGHT EMITTING DIODE (LED) TRAFFIC SIGNAL SURVEY RESULTS

    E-Print Network [OSTI]

    Joaquin County Salinas Simi Valley West Sacramento San Luis Obispo County San Anselmo Solvang Westlake

  10. Which LED Lighting Products Would You Consider Trying? | Department of

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA group currentBradley Nickell DirectorThe&ManagementEfficiencyEnergy On

  11. #AskEnergySaver: LED Lights | Department of Energy

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directed off Energy.gov. Are you sure you wantJoin us for|IdahotheWhat is the FOIA

  12. Energy - LEDs to light UT arena | ornl.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power AdministrationField Campaign:INEAWater UseCElizabethTwoJaniceEnerG2EnergeticsU.S.Energy -

  13. Demonstration Assessment of LED Post-Top Lighting.

    Office of Scientific and Technical Information (OSTI)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItem Not Found Item Not Found The itemAIR57451 Clean Energy5655994DP-1513Assessment

  14. DOE Publishes Report on Color Stability of LED Lighting Products |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: Theof"WaveInteractions and Policy (2009)| DepartmentofandPlanning

  15. REA Refrigerated Display Case LED Lighting Performance Specification |

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn April 23, 2014, an OHASeptember 2010In addition to 1 |D I S P U T E SBuilding

  16. Secretary Moniz Applauds Detroit's LED Street Lighting Upgrades |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn'tOriginEducationVideo »Usage »DownloadSolarSequestrationofPrepared fortheDepartment of

  17. (Expired) Nationwide Limited Public Interest Waiver for LED Lighting and

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: The Future of Bad CholesteroliManage#AskEnergySaver:Energy 'TisJointHVAC

  18. Save Money with LED Holiday Light Strings | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn April 23, 2014,Zaleski - Policy Advisor, Energy DepartmentAssessmentAllison Casey Senior

  19. Demonstration Assessment of LED Roadway Lighting: Philadelphia, PA |

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power Administration wouldDECOMPOSITIONPortalTo help ensure that sulfates in engineSciTech

  20. New DOE Report Estimates LED Savings in Common Lighting Applications |

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742Energy China 2015of 2005 attheMohammed Khan -DepartmentDepartment of Energy WASHINGTON,

  1. Memorandum of Decision: Withdrawal of LED Lighting Waiver | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(FactDepartment3311, 3312), OctoberMay 18-19, 2004MWMemo of- March 16, 2012

  2. Article Published on LED Lumen Maintenance and Light Loss Factors |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: The FutureComments from Tarasa U.S.LLC |AquionMr. EdwardArticle 29 Employee

  3. LED Holiday Lights: Festive, Safe, and Efficient! | Department of Energy

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directed offOCHCO2:Introduction to Energy PerformanceJohn CymbalskyKristina Johnson About UsNovember 23, 2010

  4. Have You Used LED Light Strings? | Department of Energy

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33Frequently Asked Questions for DOE FYAffairs,Assessment Documents3622,Notice ofHavasupaiHaveUsed

  5. Demonstration Assessment of Light-Emitting Diode (LED) Freezer Case

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the YouTube| DepartmentStatement Delphi Statement From October, 2008, a statement

  6. Appraisers Project Plan: Wireless Controls and Retrofit LED Lighting

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: The FutureComments from Tarasa U.S.LLC | DepartmentReport |Strategies |

  7. LED Lights for All Occasions | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742Energy ChinaofSchaeferApril 1, 1999 InspectionVolunteersKarenThis pageSeptember172ONDepartment

  8. LED Watch: The Outlook for OLEDs

    Broader source: Energy.gov [DOE]

    December 2014 LED Watch: The Outlook for OLEDs James Brodrick, U.S. Department of Energy LD+A Magazine

  9. Investigation of a moly-oxide electrodeless discharge for lighting applications

    SciTech Connect (OSTI)

    Giuliani, J.L.; Meger, R.A.; Pechacek, R.E.; Hinshelwood, D.D.; Shamamian, V.; Butler, J.E.

    1999-07-01T23:59:59.000Z

    Due to the hazardous material designation of spent fluorescent bulbs on board naval vessels, the Naval Research Laboratory has been investigating alternative lighting concepts which are free of mercury. The ideal goal is an efficient, large volume source, which provides white light directly without the use of a phosphor coating. Experiments with a {mu}wave plasma reactor normally used to diamond growth at {approximately}40 Torr revealed that a combination of O{sub 2}, N{sub 2}, and a heated molybdenum puck led to intense plasma emission in the visible domain. As the reactor was not designed for lighting studies, the authors have been investigating the process in glass tubes with a re-entry geometry and RF driven coils. Results will be presented on the initial discovery, the role of moly-oxide in surface evaporation, and the favorable emission spectrum of atomic molybdenum for visible light. Initial studies of the RF system, including coil design, measured electron density, B-dot measurements, E-to-H transitions, and spectroscopic analysis of various compositions will also be discussed. Finally, the essential problem of a recycling process for the moly emitters from the glass walls back to the moderate pressure plasma using chlorine will be addressed.

  10. DOE Solid-State Lighting Program Overview Brochure

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Lighting Program Shaping the Future of Solid-State Lighting Today, LED (light emitting diode) technologies illuminate grocery display cases, make parking garages and...

  11. Energy Department Announces Indoor Lighting Winners of Next Generation...

    Broader source: Energy.gov (indexed) [DOE]

    was launched in 2008 to promote excellence in the design of energy-efficient light-emitting diode (LED) commercial lighting fixtures or "luminaires." Solid-state lighting...

  12. advanced blue light: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of dental composites cured with blue light emitting diodes with either a light emitting diode (LED) based light curing unit (LCU) or a conventional halogen LCU do reserved....

  13. Coupled optical and electronic simulations of electrically pumped photonic-crystal-based LEDs

    E-Print Network [OSTI]

    Dutton, Robert W.

    to investigate design tradeoffs in electrically pumped photonic crystal light emitting diodes. A finite. Keywords: Photonic crystal light emitting diode, electrically pumped device 1. INTRODUCTION Recently optoelectronic devices, such as light emitting diodes (LEDs) and lasers. It has been suggested that a thin slab

  14. Ruofan Wu, Hieu Pham Trung Nguyen and Zetian Mi INTRODUCTION TO LEDs

    E-Print Network [OSTI]

    Barthelat, Francois

    -in-a-Wire Light Emitting Diodes and Prevention Method Nano-electronic Devices and Materials, Electrical Computer., Efficiency droop in nitride-based light-emitting diodes. Physica Status Solidi a-Applications and Materials history. Nature Photonics 2007, 1 (4), 189-192. [4] Holonyak, N., Is the light emitting diode (LED

  15. 3654 JOURNAL OF LIGHTWAVE TECHNOLOGY, VOL. 24, NO. 10, OCTOBER 2006 High-Sensitivity Detection of Narrowband Light in a

    E-Print Network [OSTI]

    Guillas, Serge

    -emitting diode (LED), narrowband-filtered white light, and LED signal sources in a more intense tungsten-halogen-lamp

  16. OSRAM SYLVANIA Develops High-Efficiency LED Troffer Replacement

    Broader source: Energy.gov [DOE]

    With the help of DOE funding, OSRAM SYLVANIA is developing a high-efficiency LED 2'x2' troffer replacement that is expected to be commercially available in the spring of 2012 and to be cost-competitive with existing troffers of that size. It is projected to have a light output of up to 4,000 lumens, an efficacy of more than 100 lm/W, and a CCT of 3500K.

  17. Transcranial LED therapy for cognitive dysfunction in chronic, mild traumatic brain injury: Two case reports

    E-Print Network [OSTI]

    Hamblin, Michael R.

    Two chronic, traumatic brain injury (TBI) cases are presented, where cognitive function improved following treatment with transcranial light emitting diodes (LEDs). At age 59, P1 had closed-head injury from a motor vehicle ...

  18. Deposition of colloidal quantum dots by microcontact printing for LED display technology

    E-Print Network [OSTI]

    Kim, LeeAnn

    2006-01-01T23:59:59.000Z

    This thesis demonstrates a new deposition method of colloidal quantum dots within a quantum dot organic light-emitting diode (QD-LED). A monolayer of quantum dots is microcontact printed as small as 20 ,Lm lines as well ...

  19. adjustable red-green-blue led: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    or by combining green and red phosphors on a background consisting of a blue-light emitting diode (LED) or by employing nanocrystals (NCs) of the three primary colors (red,...

  20. Text-Alternative Version: CALiPER Report Series 20 on LED PAR38 Lamps

    Broader source: Energy.gov [DOE]

    Michael Royer, Lighting Engineer, Pacific Northwest National Laboratory: The CALiPER program looks at typical LED lamp performance attributes. As we've gone through the progression of reports, we...

  1. DOE Publishes CALiPER Snapshot Report on LED MR16 Lamps

    Broader source: Energy.gov [DOE]

    The U.S. Department of Energy's CALiPER program has released a Snapshot Report on MR16 lamps, which utilizes the LED Lighting Facts® program's extensive product database to help industry...

  2. Quality and Performance of LED Flashlights in Kenya: Common End User Preferences and Complaints

    E-Print Network [OSTI]

    Tracy, Jenny

    2010-01-01T23:59:59.000Z

    grid lighting market. The lead acid batteries embedded inrechargeable sealed lead-acid batteries are the most popularlead-acid (SLA) battery, LED flashlights powered by dry cell batteries,

  3. Digital Architecture for Driving Large LED Arrays with Dynamic Bus Voltage Regulation and Phase Shifted PWM

    E-Print Network [OSTI]

    Emitting Diodes (HB-LEDs) with improved system efficiency and reduced EMI. Key advantages are achieved - This paper introduces a digital architecture suitable for driving a large number of High Brightness Light

  4. Successful Selection of LED Streetlight Luminaires: Optimizing Illumination and Economic Performance

    Broader source: Energy.gov [DOE]

    This March 6, 2013 webcast reviewed the factors involved in successful selection of LED streetlight luminaires. Presenters Eric Haugaard of Cree Lighting and Chad Stalker of Philips Lumileds guided...

  5. System and method for monitoring wet bulb temperature in a flue gas stream

    SciTech Connect (OSTI)

    Glover, R.L.; Bland, V.V.

    1990-01-02T23:59:59.000Z

    This patent describes in a system for monitoring wet bulb temperature in a flue gas stream means for extracting a sample of the gas from the flue, means for heating the sample to maintain the sample at substantially the same temperature as the gas in the flue, a sensor for measuring the wet bulb temperature of the sample, a reservoir of liquid, a liquid absorbent wick surrounding the sensor and extending into the liquid in the reservoir, and means for maintaining the liquid in the reservoir at a substantially constant level.

  6. STATEMENT OF CONSIDERATIONS REQUEST BY LUMILEDS LIGHTING, U.S...

    Broader source: Energy.gov (indexed) [DOE]

    white light LEDs and then be used in LEDs to determine their effectiveness under actual operating conditions. The program will concentrate on these key issues regarding the...

  7. Light extraction efficiency enhancement of InGaN quantum wells light-emitting diodes with

    E-Print Network [OSTI]

    Gilchrist, James F.

    Light extraction efficiency enhancement of InGaN quantum wells light-emitting diodes@lehigh.edu Abstract: Improvement of light extraction efficiency of InGaN light emitting diodes (LEDs) using microstructures on the light extraction efficiency of III-Nitride LEDs was studied. Depending on the size

  8. Quality and Performance of LED Flashlights in Kenya: Common End User Preferences and Complaints

    SciTech Connect (OSTI)

    Tracy, Jenny; Jacobson, Arne; Mills, Evan

    2009-09-14T23:59:59.000Z

    Flashlights that use LED technology have quickly emerged as the dominant source of portable lighting in Kenya. While flashlights do not normally provide a substitute for kerosene and other highly inefficient fuels, they are an important early manifestation of LED lighting in the developing world that can serve as a platform - or deterrent - to the diffusion of the technology into the broader off-grid lighting market. The lead acid batteries embedded in flashlights also represent an important source of hazardous waste, and flashlight durability is thus an important determinant of the rate of waste disposal. Low-cost LED flashlights with prices from $1 to $4 are now widely available in shops and markets throughout Kenya. The increased penetration of LED technology in the flashlight market is significant, as over half of all Kenyan households report owning a flashlight (Kamfor, 2002). While this shift from conventional incandescent technology to modern LEDs may appear to be a promising development, end users that our research team interviewed expressed a number of complaints about the quality and performance of these new flashlights. This raises concerns about the interests of low-income flashlight users, and it may also indicate the onset of a broader market spoiling effect for off-grid lighting products based on LED technology (Mills and Jacobson, 2008; Lighting Africa, 2007). The quality of low-cost LED flashlights can contribute to market spoiling because these products appear to represent the first contact that most Kenyans have with LED technology. In this report, our team uses interviews with 46 end users of flashlights to collect information about their experiences, perceptions, and preferences. We focus especially on highlighting common complaints from respondents about the flashlights that they have used, as well as on noting the features that they indicated were important when evaluating the quality of a flashlight. In previous laboratory tests, researchers from our team found a wide range of quality and performance among battery powered LED lights (Granderson, et al. 2008).

  9. Enhancing the Field of View Limitation of Visible Light Communication-based Platoon

    E-Print Network [OSTI]

    Boyer, Edmond

    . In the mean time, Light Emitting Diode (LED) has become very common in automotive lighting due to its long

  10. Engineering for Environmental Sustainability http://engineering.tufts.edu/ Energy-efficient Visible Light Communication

    E-Print Network [OSTI]

    Tufts University

    Light Communication What is the problem? The white light-emitting diode (LED) stands at the threshold

  11. Consumer Light Bulb Changes: Briefing and Resources for Media and Retailers

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 1112011AT&T, Inc.'sEnergyTexas1.SpaceFluor Federal ServicesDepartment ofDepartment of|

  12. Westinghouse Pays $50,000 Civil Penalty to Resolve Light Bulb Efficiency

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA group currentBradley Nickell DirectorThe&Management Alert Western

  13. What Light Bulbs Do You Use in Your Home? | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOn AprilA group currentBradley Nickell DirectorThe&Management AlertWhatOnOn

  14. Buying the Perfect Energy-Efficient Light Bulb in 5 Easy Steps | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the YouTube platformBuilding Removal Ongoing atGreenhouse GasesRespond to

  15. A Winning Light Bulb With the Potential to Save the Nation Billions |

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directed off Energy.gov. Are you sure you wantJoin us for|IdahotheWhatProposed - FINALAA Tale of

  16. DOE Requires Westinghouse to Cease Sales of Two Light Bulb Models and

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: Theof"WaveInteractions and PolicyCybersecurity ThreatsViolatingAllows Sale of

  17. DOE Withdraws the Energy Star Label from 34 Compact Fluorescent Light Bulbs

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: Theof"WaveInteractionsMaterials | DepartmentEnergy Will Not| Department

  18. Bulbs for Winter Bloom The trees have all dropped their leaves and our gardens are covered by a blanket of snow. It is too

    E-Print Network [OSTI]

    New Hampshire, University of

    Bulbs for Winter Bloom The trees have all dropped their leaves and our gardens are covered into an inside garden. Paperwhite Narcissus and Amaryllis bulbs both produce beautiful flowers. They are easy bulbs to grow inside a house. Paperwhites come in two colors, white and yellow. They are extremely easy

  19. Instructions for Corning Model 220 pH Meter The electrode tip is a fragile glass bulb. Be careful or you will break it with a

    E-Print Network [OSTI]

    Cross, George

    Instructions for Corning Model 220 pH Meter The electrode tip is a fragile glass bulb. Be careful a polymer body electrode can create sufficient internal pressure to "explode" the glass bulb. When of cotton in the plastic electrode cover sleeve, add pH 7 buffer, and insert the electrode bulb

  20. UNH Cooperative Extension Info Line Question of the Week Q. What should I do with the Amaryllis bulb I just received?

    E-Print Network [OSTI]

    New Hampshire, University of

    bulb I just received? A. Few flowers give greater satisfaction than the spectacular amaryllis. Amaryllis are available from September to March as dormant bulbs ready for planting. They can be purchased as bulbs or as pre packaged units complete with pots and potting medium. Shortly after planting one or two

  1. Plant Disease Note 2004 | Iris Yellow Spot Virus in Onion Bulb and Seed Crops in Washington Overview Current Issue Past Issues Search PD Search APS Journals

    E-Print Network [OSTI]

    Pappu, Hanu R.

    Plant Disease Note 2004 | Iris Yellow Spot Virus in Onion Bulb and Seed Crops in Washington Yellow Spot Virus in Onion Bulb and Seed Crops in Washington. L. J. du Toit, Washington State University of the NP gene. In August 2003, symptoms of IYSV infection were observed in two onion bulb crops, each

  2. Locally Led Conservation The Local Work Group

    E-Print Network [OSTI]

    Grants ­ Conservation Stewardship Program ­ Environmental Quality Incentive Program ­ Farm & Ranch Lands1 Locally Led Conservation & The Local Work Group Mark Habiger NRCS #12;2 What Is "Locally Led Conservation"? · Community Stakeholders ­ 1. Assessing their natural resource conservation needs ­ 2. Setting

  3. Transformations in Lighting: The Ninth Annual Solid-State Lighting...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    in DOE's "Transformations in Lighting" Solid-State Lighting (SSL) R&D Workshop. DOE SSL Portfolio Manager James Brodrick kicked off Day 1 by observing that although LED...

  4. Energy-Efficient Lighting The typical American family spends more

    E-Print Network [OSTI]

    Energy-Efficient Lighting The typical American family spends more than $1,500 a year on household their energy efficiency is taken into account. CFLs last 8­10 times longer than standard incandescent bulbs energy bills--and many households spend considerably more. Costs could climb even higher in the future

  5. Volunteer Potato Density Influences Critical Time of Weed Removal in Bulb Onion

    E-Print Network [OSTI]

    Sims, Gerald K.

    Volunteer Potato Density Influences Critical Time of Weed Removal in Bulb Onion Martin M. Williams II, Corey V. Ransom, and W. Mack Thompson* Volunteer potato is highly competitive with onion and few control tactics are effective for removing this weed from an onion crop. Both volunteer potato density

  6. U.S. Energy Information Administration (EIA) - Sector

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    incandescent bulbs. High-performance incandescent, compact fluorescent, and light-emitting diode (LED) lamps continue to replace low-efficacy incandescent lamps. In 2035,...

  7. High Power UV LED Industrial Curing Systems

    SciTech Connect (OSTI)

    Karlicek, Robert, F., Jr; Sargent, Robert

    2012-05-14T23:59:59.000Z

    UV curing is a green technology that is largely underutilized because UV radiation sources like Hg Lamps are unreliable and difficult to use. High Power UV LEDs are now efficient enough to replace Hg Lamps, and offer significantly improved performance relative to Hg Lamps. In this study, a modular, scalable high power UV LED curing system was designed and tested, performing well in industrial coating evaluations. In order to achieve mechanical form factors similar to commercial Hg Lamp systems, a new patent pending design was employed enabling high irradiance at long working distances. While high power UV LEDs are currently only available at longer UVA wavelengths, rapid progress on UVC LEDs and the development of new formulations designed specifically for use with UV LED sources will converge to drive more rapid adoption of UV curing technology. An assessment of the environmental impact of replacing Hg Lamp systems with UV LED systems was performed. Since UV curing is used in only a small portion of the industrial printing, painting and coating markets, the ease of use of UV LED systems should increase the use of UV curing technology. Even a small penetration of the significant number of industrial applications still using oven curing and drying will lead to significant reductions in energy consumption and reductions in the emission of green house gases and solvent emissions.

  8. Sixth International Conference on Solid State Lighting, edited by Ian T. Ferguson, Nadarajah Narendran, Tsunemasa Taguchi, Ian E. Ashdown,

    E-Print Network [OSTI]

    Weiss, Sharon

    commercial white light emitting diodes (LEDs) rely on complicated fabrication methods to produce white light: Cadmium Selenide, Nanocrystal, Photoluminescence, Phosphor, White Light, Light Emitting Diode, LED 1. INTRODUCTION 1.1 Solid state lighting Solid state lighting, in the form of white light emitting diodes (LEDs

  9. Typically, hotel bathroom lights are left on between five to eight hours per occupied

    E-Print Network [OSTI]

    -public spaces, the energy efficient, super bright light-emitting diode (LED) nightlight remains on whenever

  10. Toward ZnO Light Emitting Diode

    E-Print Network [OSTI]

    Liu, Jianlin

    2008-01-01T23:59:59.000Z

    applications such as light emitting diodes (LEDs) and laser009 "Toward ZnO Light Emitting Diode" Jianlin Liu July 2008Title: “Toward ZnO Light Emitting Diode” Sponsor: UC Energy

  11. EECBG Success Story: Lighting Retrofit Improving Visibility,...

    Broader source: Energy.gov (indexed) [DOE]

    New LED lighting fixtures (right) emit a whiter light than existing high-pressure sodium cobra head streetlights (left) and don't spill light onto nearby houses. | Photos courtesy...

  12. Embodied Energy and Off-Grid Lighting

    E-Print Network [OSTI]

    Alstone, Peter

    2012-01-01T23:59:59.000Z

    Self-reported Impacts of LED Lighting Technology Comparedto Fuel-based Lighting on Night Market Business Prosperity28, no. 4, pp. 533-546. Lighting Africa (prepared by Dalberg

  13. Beyond the Replacement Paradigm: Smart Lighting

    E-Print Network [OSTI]

    Salama, Khaled

    Switches · Smart Building & Grid Interfaces · Efficient full spectrum LEDs without droop · Versatile, low - Visible Light Communications Integration of smart fixtures, networked sensors and control systemsBeyond the Replacement Paradigm: Smart Lighting Robert F. Karlicek, Jr. Director, Smart Lighting

  14. Decisions that led to Y-12

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    German physicists Otto Hahn and Fritz Strass- mann's claim that they had achieved nuclear fission. He led a team that included Alfred O. C. Nier who was an expert on mass...

  15. LEDS-An overview of the state of the art in technology and application

    SciTech Connect (OSTI)

    Johnson, Stephen

    2002-03-01T23:59:59.000Z

    Solid state lighting in the form of Light Emitting Diodes (LEDs) is bringing new sources with different operating characteristics to the market. With the control in dimension, optics, intensity and color, these sources have the potential to transform the way we use light. This paper will review the recent improvements in performance that have been achieved by these devices, focusing on those product attributes identified as being critical to end users. The paper will conclude with a consideration of applications capitalizing on the LEDs' unique operating and physical properties.

  16. Application Summary Report 22: LED MR16 Lamps

    SciTech Connect (OSTI)

    Royer, Michael P.

    2014-07-23T23:59:59.000Z

    This report analyzes the independently tested photometric performance of 27 LED MR16 lamps. It describes initial performance based on light output, efficacy, distribution, color quality, electrical characteristics, and form factor, with comparisons to a selection of benchmark halogen MR16s and ENERGY STAR qualification thresholds. Three types of products were targeted. First, CALiPER sought 3000 K lamps with the highest rated lumen output (i.e., at least 500 lm) or a claim of equivalency to a 50 W halogen MR16 or higher. The test results indicate that while the initial performance of LED MR16s has improved across the board, market-available products still do not produce the lumen output and center beam intensity of typical 50 W halogen MR16 lamps. In fact, most of the 18 lamps in this category had lower lumen output and center beam intensity than a typical 35 W halogen MR16 lamp. Second, CALiPER sought lamps with a CRI of 90 or greater. Only four manufacturers were identified with a product in this category. CALiPER testing confirmed the performance of these lamps, which are a good option for applications where high color fidelity is needed. A vast majority of the LED MR16 lamps have a CRI in the low 80s; this is generally acceptable for ambient lighting, but may not always be acceptable for focal lighting. For typical LED packages, there is a fundamental tradeoff between CRI and efficacy, but the lamps in the high-CRI group in this report still offer comparable performance to the rest of the Series 22 products in other performance areas. Finally, CALiPER sought lamps with a narrow distribution, denoted as a beam angle less than 15°. Five such lamps were purchased. Notably, no lamp was identified as having high lumen output (500 lumens or greater), high CRI (90 or greater), a narrow distribution (15° or less), and an efficacy greater than 60 lm/W. This would be an important achievement for LED MR16s especially if output could reach approximately 700 800 lumens, or the approximate equivalent of a 50 W halogen MR16 lamp. Many factors beyond photometric performance should be considered during specification. For example, performance over time, transformer and dimmer compatibility, and total system performance are all critical to a successful installation. Subsequent CALiPER reports will investigate more complex issues.

  17. LEDS GP Success Story: Fostering Coordinated LEDS Support in Kenya (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2014-03-01T23:59:59.000Z

    The LEDS Global Partnership (LEDS GP) strives to advance climate-resilient, low-emission development through catalyzing collaboration, information exchange, and action on the ground. The Government of Kenya is a key LEDS GP member and offers an inspiring example of how LEDS GP is having an impact globally. The 2012 LEDS Collaboration in Action workshop in London provided an interactive space for members to share experiences on cross-ministerial LEDS leadership and to learn about concrete development impacts of LEDS around the world. Inspired by these stories, the Kenya's Ministry of State for Planning, National Development and Vision 2030 (MPND) began to collaborate closely with the Ministry of Environment and Mineral Resources to create strong links between climate change action and development in the country, culminating in the integration of Kenya's National Climate Change Action Plan and the country's Medium Term Development Plan.

  18. Energy Efficiency of LEDs | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    application efficacy. ledenergyefficiency.pdf More Documents & Publications Outdoor Area Lighting Solid-State Lighting R&D Multi-Year Program Plan SSL R&D Multi-Year Program Plan...

  19. White light emitting diode as liquid crystal display backlight

    E-Print Network [OSTI]

    Soon, Chian Myau

    2007-01-01T23:59:59.000Z

    The discovery of high brightness (white) light emitting diode (LED) is considered as a real threat to the current lighting industry in various applications. One of the most promising sectors would be using white LED to ...

  20. Apply: Solid-State Lighting Advanced Technology R&D - 2014(DE...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Through research and development of solid-state lighting (SSL),including both light-emitting diode (LED) and organic light emitting diode (OLED) technologies, the objectives of...

  1. artificial blue-light photoreceptors: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of dental composites cured with blue light emitting diodes with either a light emitting diode (LED) based light curing unit (LCU) or a conventional halogen LCU do reserved....

  2. Some cultural practices affecting bulb rot, plant and floral development, and seed yield of the White Grano onion

    E-Print Network [OSTI]

    Enzie, Joseph Vincent

    1955-01-01T23:59:59.000Z

    L IBRARY A&IW COLLEGE OF TEXAS SOME CULTURAL PRACTICES AFFECTING BULB ROT, PLANT AND FLORAL DEVELOPMENT, AND SEED YIELD OF THE WHITE GRANO ONION A Dissertation By JOSEPH V. ENZIE Submitted to the Graduate School of the Agricultural... and Mechanical College of Texas in partial fulfillment of the requirements for the degree of DOCTOR OF PHILOSOPHY May 1955 Major Subject: Horticulture SOME CULTURAL PRACTICES AFFECTING BULB ROT, PLANT AND FLORAL DEVELOPMENT, AND SEED YIELD OF THE WHITE GRANO...

  3. 130 LPW 1000 Lm Warm White LED for Illumination

    SciTech Connect (OSTI)

    Soer, Wouter

    2012-06-14T23:59:59.000Z

    An illumination-grade warm-white LED, having correlated color temperature (CCT) between 2700 and 3500 K and capable of producing 1000 lm output at over 130 lm/W at room temperature, has been developed in this program. The high-power warm-white LED is an ideal source for use in indoor and outdoor lighting applications. Over the two year period, we have made the following accomplishments: • Developed a low-cost high-power white LED package and commercialized a series of products with CCT ranging from 2700 to 5700 K under the product name LUXEON M; • Demonstrated a record efficacy of 124.8 lm/W at a flux of 1023 lm, CCT of 3435 K and color rendering index (CRI) over 80 at room temperature in the productized package; • Demonstrated a record efficacy of 133.1 lm/W at a flux of 1015 lm, CCT of 3475 K and CRI over 80 at room temperature in an R&D package. The new high-power LED package is a die-on-ceramic surface mountable LED package. It has four 2 mm2 InGaN pump dice, flip-chip attached to a ceramic submount in a 2x2 array configuration. The submount design utilizes a design approach that combines a high-thermal- conductivity ceramic core for die attach and a low-cost and low-thermal-conductivity ceramic frame for mechanical support and as optical lens carrier. The LED package has a thermal resistance of less than 1.25 K/W. The white LED fabrication also adopts a new batch level (instead of die-by-die) phosphor deposition process with precision layer thickness and composition control, which provides not only tight color control, but also low cost. The efficacy performance goal was achieved through the progress in following key areas: (1) high-efficiency royal blue pump LED development through active region design and epitaxial growth quality improvement (funded by internal programs); (2) improvement in extraction efficiency from the LED package through improvement of InGaN-die-level and package-level optical extraction efficiency; and (3) improvement in phosphor system efficiency by improving the lumen equivalent (LE) and phosphor package efficiency (PPE) through improvement in phosphor-package interactions. The high-power warm-white LED product developed has been proven to have good reliability through extensive reliability tests. The new kilo-lumen package has been commercialized under the product name LUXEON M. As of the end of the program, the LUXEON M product has been released in the following CCT/CRI combinations: 3000K/70, 4000K/70, 5000K/70, 5700K/70, 2700K/80, 3000K/80 and 4000K/80. LM-80 tests for the products with CCTs of 4000 K and higher have reached 8500 hours, and per IESNA TM-21-11 have established an L70 lumen maintenance value of >51,000 hours at A drive current and up to 120 °C board temperature.

  4. Shaping the Next - Buildings and Energy: Advanced Lighting

    SciTech Connect (OSTI)

    Richman, Eric E.

    2014-01-01T23:59:59.000Z

    short bit on advanced lighting for the future relating specifically to controls and new tech such as LEDs

  5. Marine Corps Base Quantico Achieves 85% Savings in Parking Lighting...

    Broader source: Energy.gov (indexed) [DOE]

    conducting a major overhaul of its outdoor lighting (replacing 2,000 fixtures with LED lights), while boosting safety and security throughout the site. mcbquantico2014.pdf More...

  6. I Have Seen the Light and It's Green...or Pink, or Blue, or Purple...

    Office of Environmental Management (EM)

    or Blue, or Purple. Shucks, it's LED Solid-State Lighting. I Have Seen the Light and It's Green...or Pink, or Blue, or Purple. Shucks, it's LED Solid-State Lighting. May 5, 2009 -...

  7. High Efficacy Green LEDs by Polarization Controlled MOVPE

    SciTech Connect (OSTI)

    Wetzel, Christian

    2013-03-31T23:59:59.000Z

    Amazing performance in GaInN/GaN based LEDs has become possible by advanced epitaxial growth on a wide variety of substrates over the last decade. An immediate push towards product development and worldwide competition for market share have effectively reduced production cost and generated substantial primary energy savings on a worldwide scale. At all times of the development, this economic pressure forced very fundamental decisions that would shape huge industrial investment. One of those major aspects is the choice of epitaxial growth substrate. The natural questions are to what extend a decision for a certain substrate will limit the ultimate performance and to what extent, the choice of a currently more expensive substrate such as native GaN could overcome any of the remaining performance limitations. Therefore, this project has set out to explore what performance characteristic could be achieved under the utilization of bulk GaN substrate. Our work was guided by the hypotheses that line defects such as threading dislocations in the active region should be avoided and the huge piezoelectric polarization needs to be attenuated – if not turned off – for higher performing LEDs, particularly in the longer wavelength green and deep green portions of the visible spectrum. At their relatively lower performance level, deep green LEDs are a stronger indicator of relative performance improvements and seem particular sensitive to the challenges at hand. The project therefore made use of recently developed non-polar and semipolar bulk GaN substrates that were made available at Kyma Technologies by crystallographic cuts from thick polar growth of GaN. This approach naturally leads to rather small pieces of substrates, cm along the long side while mm along the short one. Small size and limited volume of sample material therefore set the limits of the ensuing development work. During the course of the project we achieved green and deep green LEDs in all those crystal growth orientations: polar c-plane, non- polar a-plane, non-polar m-plane, and semipolar planes. The active region in those structures shows dramatically reduced densities of threading dislocations unless the wavelength was extended as far as 510 nm and beyond. With the appearance of such defects, the light output power dropped precipitously supporting the necessity to avoid any and all of such defects to reach the active region. Further aspects of the non-polar growth orientation proved extremely promising for the development of such structures. Chief among them is our success to achieve extremely uniform quantum wells in these various crystal orientations that prove devoid of any alloy fluctuation beyond the theoretical limit of a binominal distribution. This became very Rensselaer Wetzel DE?EE0000627 3 directly apparent in highly advanced atom probe tomography performed in collaboration at Northwestern University. Furthermore, under reduced or absence of piezoelectric polarization, green emitters in those growth geometries exhibit an unsurpassed wavelength stability over very wide excitation and drive current ranges. Such a performance had not been possible in any polar c-plane growth and now places green LEDs in terms of wavelength stability up par with typical 450 nm blue emitters. The project also incorporated enabling opportunities in the development of micro and nano- patterned substrate technologies. Originally developped as a means to enhance generated light extraction we have demonstrated that the method of nano-patterning, in contrast to micro- patterning also results in a substantial reduction of threading dislocation generation. In green LEDs, we thereby see equal contributions of enhanced light extraction and reduced defect generation to a threefold enhancement of the green light output power. These results have opened entirely new approaches for future rapid and low cost epitaxial material development by avoidance of thick defect accommodation layers. All methods developed within this project have meanwhile widely been publicized by the members o

  8. LED exit signs: Improved technology leads the way to energy savings

    SciTech Connect (OSTI)

    Sardinsky, R.; Hawthorne, S.

    1994-12-31T23:59:59.000Z

    Recent innovations in light-emitting diode (LED) exit signs may make LED signs the best choice among the energy efficient options available. In the past, LED signs have offered low power consumption, projected long lamp life, and low maintenance requirements. Now, the best of the LED signs also offer improved optical designs that reduce their already low power consumption while improving visibility and appearance, and even reduce their cost. LED exit signs are gaining market share, and E Source expects this technology to eventually dominate over incandescent, compact fluorescent, and electroluminescent signs. More research is needed, however, to confirm manufacturers` claims of 20-year operating lives for LED signs. Conservative estimates place the number of exit signs in US buildings at about 40 million. Although each sign represents a very small part of a building`s load, exit signs are ready targets for energy efficiency upgrades -- they operate continuously and most use inefficient incandescent sources. With an LED sign, annual energy and maintenance costs can be reduced by more than 90 percent compared to a typical incandescent sign. Low annual costs help to offset the LED sign`s relatively high first cost. More than 25 utilities offer DSM incentives for energy efficient exit signs, and efficient alternatives are becoming more readily available. Recent improvements in optical designs enable many LED signs to visually out perform other sources. In addition to these benefits, LED exit signs have lower life cycle cost than most other options. The biggest barrier to their success, however, is that their first cost has been considerably higher than competing technologies. LED sign prices are falling rapidly, though, because manufacturers are continually improving optical designs of the fixtures to use fewer LEDs and thus even less energy while providing better performance.

  9. LED-Induced Fluorescence System for Tea Classification and Quality Assessment

    E-Print Network [OSTI]

    Dong, Yongjiang; Mei, Liang; Feng, Chao; Yan, Chunsheng; He, Sailing

    2013-01-01T23:59:59.000Z

    A fluorescence system is developed by using several light emitting diodes (LEDs) with different wavelengths as excitation light sources. The fluorescence detection head consists of multi LED light sources and a multimode fiber for fluorescence collection, where the LEDs and the corresponding filters can be easily chosen to get appropriate excitation wavelengths for different applications. By analyzing fluorescence spectra with the principal component analysis method, the system is utilized in the classification of four types of green tea beverages and two types of black tea beverages. Qualities of the Xihu Longjing tea leaves of different grades, as well as the corresponding liquid tea samples, are studied to further investigate the ability and application of the system in the evaluation of classification/quality of tea and other foods.

  10. Assessment of LED Technology in Ornamental Post-Top Luminaires (Host Site: Sacramento, CA)

    SciTech Connect (OSTI)

    Tuenge, Jason R.

    2011-12-01T23:59:59.000Z

    The DOE Municipal Solid-State Street Lighting Consortium has evaluated four different LED replacements for existing ornamental post-top street lights in Sacramento, California. The project team was composed of the City and its consultant, PNNL (representing the Consortium), and the Sacramento Municipal Utility District. Product selection was finalized in March 2011, yielding one complete luminaire replacement and three lamp-ballast retrofit kits. Computer simulations, field measurements, and laboratory testing were performed to compare the performance and cost-effectiveness of the LED products relative to the existing luminaire with 100 W high-pressure sodium lamp. After it was confirmed the LED products were not equivalent to HPS in terms of initial photopic illumination, the following parameters were scaled proportionally to enable equitable (albeit hypothetical) comparisons: light output, input wattage, and pricing. Four replacement scenarios were considered for each LED product, incorporating new IES guidance for mesopic multipliers and lumen maintenance extrapolation, but life cycle analysis indicated cost effectiveness was also unacceptable. Although LED efficacy and pricing continue to improve, this project serves as a timely and objective notice that LED technology may not be quite ready yet for such applications.

  11. Sandia National Laboratories: warm white LED

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Unfortunately, red emitters that satisfy all criteria for use in solid-state lighting (SSL) applications are ... Last Updated: May 23, 2013 Go To Top Exceptional service in...

  12. Demonstration of LED Retrofit Lamps at the Smithsonian American Art Museum, Washington, DC

    SciTech Connect (OSTI)

    Miller, Naomi J.; Rosenfeld, Scott M.

    2012-06-22T23:59:59.000Z

    This report documents observations and results obtained from a lighting demonstration project conducted under the U.S. Department of Energy GATEWAY Solid-State Lighting (SSL) Technology Demonstration Program at the Smithsonain American Art Museum in Washington, DC. LED Lamp samples were tested in the museum workshop, temporarily installed in a gallery for feedback, and ultimately replaced all traditional incandescent lamps in one gallery of modernist art at the American Art Museum and partially replacing lamps in two galleries at the Musesum's Renwick Gallery. This report describes the selection and testing process, technology challenges, perceptions, economics, energy use, and mixed results of usign LED replacement lamps in art galleries housing national treasures.

  13. Table Set-up with equipment Target Audience: Parents of elementary school students (grades 3-6), Middle and High School Students

    E-Print Network [OSTI]

    Linhardt, Robert J.

    on significantly different technology (e.g. incandescent, CFL, LED) as an example of information on light bulbs simple reflector lamps (clamp on) for display of bulbs (desk lamp is good because of the length of the support). Table of lamp specifications for a variety of standard bulbs available from national chains (e

  14. Long-term Testing Results for the 2008 Installation of LED Luminaires at the I-35 West Bridge in Minneapolis

    SciTech Connect (OSTI)

    Kinzey, Bruce R.; Davis, Robert G.

    2014-09-30T23:59:59.000Z

    This document reports the long-term testing results from an extended GATEWAY project that was first reported in “Demonstration Assessment of Light-Emitting Diode (LED) Roadway Lighting at the I-35W Bridge, in Minneapolis, MN,” August 2009. That original report presented the results of lighting the newly reconstructed I 35W Bridge using LEDs in place of conventional high-pressure sodium (HPS) roadway luminaires, comparing energy use and illuminance levels with a simulated baseline condition. That installation was an early stage implementation of LED lighting and remains one of the oldest installations in continued operation today. This document provides an update of the LED system’s performance since its installation in September 2008.

  15. Nice, Cte d'Azur, France, 27-29 September 2006 THERMAL MODELING OF HIGH POWER LED MODULES

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    generation a part of the input electric power is converted into light, which is described by the wall plugNice, Côte d'Azur, France, 27-29 September 2006 THERMAL MODELING OF HIGH POWER LED MODULES D a study of accuracy issues in thermal modeling of high power LED modules on system level. Both physical

  16. Current crowding in GaInN / GaN LEDs grown on insulating substrates X. Guo, E. F. Schubert and J. Jahns

    E-Print Network [OSTI]

    Jahns, Jürgen

    Current crowding in GaInN / GaN LEDs grown on insulating substrates X. Guo, E. F. Schubert and J spreading in a mesa-structure GaN-based LED grown on an insulating or semi-insulating substrate. (b. Jahns Current crowding in mesa-structure GaInN/GaN light-emitting diodes (LEDs) grown on insulating

  17. DOE Science Showcase - Light-emitting Diode (LED) Lighting Research | OSTI,

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisitingContract Management Fermi SitePART IScientificScientific andOffice ofUS Dept

  18. Demonstration Assessment of Light-Emitting Diode (LED) Post-Top Lighting at

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power Administration wouldDECOMPOSITIONPortalTo help ensure that sulfates in

  19. Energy Department Announces New University-Led Projects to Create...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    University-Led Projects to Create More Efficient, Lower Cost Concentrating Solar Power Systems Energy Department Announces New University-Led Projects to Create More Efficient,...

  20. Research Led by Sandia Reveals Leading-Edge Erosion Significantly...

    Broader source: Energy.gov (indexed) [DOE]

    Research Led by Sandia Reveals Leading-Edge Erosion Significantly Reduces Wind Turbine Performance Research Led by Sandia Reveals Leading-Edge Erosion Significantly Reduces Wind...

  1. Life-Cycle Assessment of Energy and Environmental Impacts of LED Lighting Products Part 3: LED Environmental Testing

    Office of Scientific and Technical Information (OSTI)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItem Not Found Item Not Found TheHot electron dynamics in807 DE89 002669LifeBUILDING

  2. Life-Cycle Assessment of Energy and Environmental Impacts of LED Lighting Products, Part 2: LED Manufacturing and Performance

    Office of Scientific and Technical Information (OSTI)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItem Not Found Item Not Found TheHot electron dynamics in807 DE89 002669LifeBUILDINGfor:

  3. Seventh International Conference on Solid State Lighting, Edited by Ian T. Ferguson, Nadarajah Narendran, Tsunemasa Taguchi, Ian E. Ashdown,

    E-Print Network [OSTI]

    Weiss, Sharon

    Selenide, Nanocrystal, Photoluminescence, Phosphor, White Light, Light Emitting Diode, LED 1. INTRODUCTION 1.1 Solid state lighting and white-light LEDs The use of white light emitting diodes (LEDs emitting diodes[11] , though they are a less mature technology as compared to inorganic semiconductor

  4. LED North America - Energy Innovation Portal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHigh SchoolIn12electron 9 5 - -/e),,s - 1 2 3 4 5 6 7 8 9LDRD, What doesLED

  5. White LED with High Package Extraction Efficiency

    Office of Scientific and Technical Information (OSTI)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItem Not Found Item Not Found The item youTheWSRC-TR-97-0100WHITE LED WITH HIGH PACKAGE

  6. SemiLEDs | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are beingZealand Jump to:Ezfeedflag JumpID-f < RAPID‎ |Rippey JumpAir JumpCalifornia | OpenSelawik|SemiLEDs Jump

  7. SunLed Technologies | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere IRaghuraji Agro Industries PvtStratosolar Jump to: navigation,SunElectra Jump to: navigation,SunLed

  8. Recessed LED Downlights | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn'tOrigin of ContaminationHubs+18, 2012 Qualified11Department ofMeetingSynthetic DieselRecessed LED

  9. Light-Emitting Diodes in the Solid-State Lighting Systems

    E-Print Network [OSTI]

    Sparavigna, Amelia Carolina

    2014-01-01T23:59:59.000Z

    Red and green light-emitting diodes (LEDs) had been produced for several decades before blue emitting diodes, suitable for lighting applications, were widely available. Today, we have the possibility of combining the three fundamental colours to have a bright white light. And therefore, a new form of lighting, the solid-state lighting, has now become a reality. Here we discuss LEDs and some of their applications in displays and lamps.

  10. Epitaxial Growth of GaN-based LEDs on Simple Sacrificial Substrates

    SciTech Connect (OSTI)

    Ian Ferguson; Chris Summers

    2009-12-31T23:59:59.000Z

    The objective of this project is to produce alternative substrate technologies for GaN-based LEDs by developing an ALD interlayer of Al{sub 2}O{sub 3} on sacrificial substrates such as ZnO and Si. A sacrificial substrate is used for device growth that can easily be removed using a wet chemical etchant leaving only the thin GaN epi-layer. After substrate removal, the GaN LED chip can then be mounted in several different ways to a metal heat sink/reflector and light extraction techniques can then be applied to the chip and compared for performance. Success in this work will lead to high efficiency LED devices with a simple low cost fabrication method and high product yield as stated by DOE goals for its solid state lighting portfolio.

  11. Embodied Energy and Off-Grid Lighting

    E-Print Network [OSTI]

    Alstone, Peter

    2012-01-01T23:59:59.000Z

    Life Cycle Assessment of Off-Grid Lighting Applications:Testing for Emerging Off-grid White-LED Illumination SystemsBudget: The Economics of Off-Grid Lighting for Small

  12. Text-Alternative Version: LED Essentials- Technology, Applications, Advantages, Disadvantages

    Broader source: Energy.gov [DOE]

    Below is the text-alternative version of the LED Essentials - Technology, Applications, Advantages, Disadvantages webcast.

  13. COMMUNIQU DE PRESSE NATIONAL I PARIS I 31 JANVIER 2014 La course la miniaturisation des diodes lectroluminescentes (DEL, en anglais : Light-

    E-Print Network [OSTI]

    Arleo, Angelo

    diodes électroluminescentes (DEL, en anglais : Light- Emitting Diode, LED) vient sans doute de franchir l

  14. Observed Minimum Illuminance Threshold for Night Market Vendors in Kenya who use LED Lamps

    SciTech Connect (OSTI)

    Johnstone, Peter; Jacobson, Arne; Mills, Evan; Radecsky, Kristen

    2009-03-21T23:59:59.000Z

    Creation of light for work, socializing, and general illumination is a fundamental application of technology around the world. For those who lack access to electricity, an emerging and diverse range of LED based lighting products hold promise for replacing and/or augmenting their current fuel-based lighting sources that are costly and dirty. Along with analysis of environmental factors, economic models for total cost-ofownership of LED lighting products are an important tool for studying the impacts of these products as they emerge in markets of developing countries. One important metric in those models is the minimum illuminance demanded by end-users for a given task before recharging the lamp or replacing batteries. It impacts the lighting service cost per unit time if charging is done with purchased electricity, batteries, or charging services. The concept is illustrated in figure 1: LED lighting products are generally brightest immediately after the battery is charged or replaced and the illuminance degrades as the battery is discharged. When a minimum threshold level of illuminance is reached, the operational time for the battery charge cycle is over. The cost to recharge depends on the method utilized; these include charging at a shop at a fixed price per charge, charging on personal grid connections, using solar chargers, and purchasing dry cell batteries. This Research Note reports on the observed"charge-triggering" illuminance level threshold for night market vendors who use LED lighting products to provide general and task oriented illumination. All the study participants charged with AC power, either at a fixed-price charge shop or with electricity at their home.

  15. Wire-shaped semiconductor light-emitting diodes for general-purpose lighting

    SciTech Connect (OSTI)

    Mauk, Michael G.

    2002-10-28T23:59:59.000Z

    The object of this work is to develop and optimize a new type of light-emitting diode (LED) with a wire-shaped, cylindrical geometry.

  16. A strategy for the use of light emitting diodes by autonomous underwater vehicles

    E-Print Network [OSTI]

    Curran, Joseph R. (Joseph Robinson)

    2004-01-01T23:59:59.000Z

    Light Emitting Diode (LED) technology has advanced dramatically in a few short years. An expensive and difficult to manufacture LED array containing nearly 100 individual LEDs and measuring at least 5 cm² can now be replaced ...

  17. Over the past decade, lighting became more efficient across all...

    Broader source: Energy.gov (indexed) [DOE]

    of light output (in lumen-hours) provided by each lamp type. "Other" includes light-emitting diode (LED) lamps as well as other lamps such as fiber optic lights, induction lamps,...

  18. Scientists at the National Renewable Energy Laboratory (NREL) invent a deep green LED that can lead to higher-efficiency

    E-Print Network [OSTI]

    Scientists at the National Renewable Energy Laboratory (NREL) invent a deep green LED that can lead by the so-called "green gap:"the inability to develop light in the green spectrum that can be combined with red and blue to produce white light. NREL researchers conceptualized a green emission by taking

  19. ONION (Allium cepa, 47 cultivars) B.K. Schroeder, Washington State University (WSU), Pullman, Enterobacter bulb decay; Enterobacter cloacae WA 99164; T.D. Waters, WSU Franklin Co. Extension, Pasco WA

    E-Print Network [OSTI]

    Schroeder, Brenda K.

    , Enterobacter bulb decay; Enterobacter cloacae WA 99164; T.D. Waters, WSU Franklin Co. Extension, Pasco WA 99301 in storage in Washington State, 2008-2009. An onion bulb storage trial was completed to survey 47 storage to Enterobacter cloacae, causal agent of Enterobacter bulb decay. Seeds of each cultivar were planted near Pasco

  20. ONION (Allium cepa, 55 cultivars) B.K. Schroeder, Washington State University (WSU), Pullman, Enterobacter bulb decay; Enterobacter cloacae WA 99164; T. Waters, WSU Franklin Co. Extension, Pasco WA

    E-Print Network [OSTI]

    Schroeder, Brenda K.

    , Enterobacter bulb decay; Enterobacter cloacae WA 99164; T. Waters, WSU Franklin Co. Extension, Pasco WA 99301 for resistance to Enterobacter cloacae in storage, 2007-2008. An onion bulb storage trial was completed to survey for resistance to Enterobacter cloacae, causal agent of Enterobacter bulb decay. Seeds of each cultivar were