National Library of Energy BETA

Sample records for leachate collection system

  1. Leachate treatment system using constructed wetlands, Town of Fenton sanitary landfill, Broome County, New York. Final report

    SciTech Connect (OSTI)

    Not Available

    1993-11-01

    Municipal sanitary landfills generate leachate that New York State regulations require to be collected and treated to avoid contaminating surface water and groundwater. One option for treating leachate is to haul it to municipal wastewater treatment facility. This option may be expensive, may require excessive energy for transportation, and may require pretreatment to protect the receiving facility`s processes. An alternative is on-site treatment and discharge. Personnel from the Town of Fenton, New York; Hawk Engineering, P.C.; Cornell University; and Ithaca College designed, built, and operated a pilot constructed wetland for treating leachate at the Town of Fenton`s municipal landfill. The system, consisting of two overland flow beds and two subsurface flow beds has been effective for 18 months in reducing levels of ammonia (averaging 85% removal by volatilization and denitrification) and total iron (averaging 95% removal by precipitation and sedimentation), two key constituents of the Fenton landfill`s leachate. The system effects these reductions with zero chemical and energy inputs and minimal maintenance. A third key constituent of the leachate, manganese, apparently passes through the beds with minimal removal. Details and wetland considerations are described.

  2. Treatment of municipal landfill leachate using a combined anaerobic digester and activated sludge system

    SciTech Connect (OSTI)

    Kheradmand, S.; Karimi-Jashni, A.; Sartaj, M.

    2010-06-15

    The main objective of this study was to assess the feasibility of treating sanitary landfill leachate using a combined anaerobic and activated sludge system. A high-strength leachate from Shiraz municipal landfill site was treated using this system. A two-stage laboratory-scale anaerobic digester under mesophilic conditions and an activated sludge unit were used. Landfill leachate composition and characteristics varied considerably during 8 months experiment (COD concentrations of 48,552-62,150 mg/L). It was found that the system could reduce the COD of the leachate by 94% at a loading rate of 2.25 g COD/L/d and 93% at loading rate of 3.37 g COD/L/d. The anaerobic digester treatment was quite effective in removing Fe, Cu, Mn, and Ni. However, in the case of Zn, removal efficiency was about 50%. For the rest of the HMs the removal efficiencies were in the range 88.8-99.9%. Ammonia reduction did not occur in anaerobic digesters. Anaerobic reactors increased alkalinity about 3.2-4.8% in the 1st digester and 1.8-7.9% in the 2nd digester. In activated sludge unit, alkalinity and ammonia removal efficiency were 49-60% and 48.6-64.7%, respectively. Methane production rate was in the range of 0.02-0.04, 0.04-0.07, and 0.02-0.04 L/g COD{sub rem} for the 1st digester, the 2nd digester, and combination of both digesters, respectively; the methane content of the biogas varied between 60% and 63%.

  3. Collection Mode Lens System

    DOE Patents [OSTI]

    Fletcher, Daniel A. (Menlo Park, CA); Kino, Gordon S. (Stanford, CA)

    2002-11-05

    A lens system including a collection lens and a microlens spaced from the collection lens adjacent the region to be observed. The diameter of the observablel region depends substantially on the radius of the microlens.

  4. Phytoremediation of landfill leachate

    SciTech Connect (OSTI)

    Jones, D.L. . E-mail: d.jones@bangor.ac.uk; Williamson, K.L.; Owen, A.G.

    2006-07-01

    Leachate emissions from landfill sites are of concern, primarily due to their toxic impact when released unchecked into the environment, and the potential for landfill sites to generate leachate for many hundreds of years following closure. Consequently, economically and environmentally sustainable disposal options are a priority in waste management. One potential option is the use of soil-plant based remediation schemes. In many cases, using either trees (including short rotation coppice) or grassland, phytoremediation of leachate has been successful. However, there are a significant number of examples where phytoremediation has failed. Typically, this failure can be ascribed to excessive leachate application and poor management due to a fundamental lack of understanding of the plant-soil system. On balance, with careful management, phytoremediation can be viewed as a sustainable, cost effective and environmentally sound option which is capable of treating 250 m{sup 3} ha{sup -1} yr{sup -1}. However, these schemes have a requirement for large land areas and must be capable of responding to changes in leachate quality and quantity, problems of scheme establishment and maintenance, continual environmental monitoring and seasonal patterns of plant growth. Although the fundamental underpinning science is well understood, further work is required to create long-term predictive remediation models, full environmental impact assessments, a complete life-cycle analysis and economic analyses for a wide range of landfill scenarios.

  5. Motor Current Data Collection System

    Energy Science and Technology Software Center (OSTI)

    1992-12-01

    The Motor Current Data Collection System (MCDCS) uses IBM compatible PCs to collect, process, and store Motor Current Signature information.

  6. Solar energy collection system

    SciTech Connect (OSTI)

    Hummel, R.L.

    1982-04-06

    A solar energy collection system for a building is described. A solar energy collector is disposed at the exterior surface of the building and includes a solar energy absorbent body having a surface which is exposed to sunlight and from which solar energy can be transmitted as sensible heat. A panel which is transparent to sunlight is spaced from the said surface of the absorbent body so as to define therewith a passageway in which air contacts at least a substantial area of said surface so that air in said passageway absorbs heat transmitted from said surface when the collector is in use. The passageway has an inlet and an outlet and the absorbent body and panel are arranged with the outlet higher than the inlet so that heated air in the passageway tends to rise by convection towards the outlet. The building is provided with heating means including a circulation circuit for a heating fluid. Heat exchange means are coupled to said air passageway outlet of the solar energy collector for passage of heated air therethrough. The heat exchange means are also coupled to the circulation circuit of the building heating means and are arranged to permit heat transfer between said heated air and the heating fluid. A return air flow conduit is coupled between the heat exchange means and the inlet of the air passageway of the solar energy collector for returning heated air from the heat exchange means to the air passageway for recirculation.

  7. Tritium monitor and collection system

    DOE Patents [OSTI]

    Bourne, G.L.; Meikrantz, D.H.; Ely, W.E.; Tuggle, D.G.; Grafwallner, E.G.; Wickham, K.L.; Maltrud, H.R.; Baker, J.D.

    1992-01-14

    This system measures tritium on-line and collects tritium from a flowing inert gas stream. It separates the tritium from other non-hydrogen isotope contaminating gases, whether radioactive or not. The collecting portion of the system is constructed of various zirconium alloys called getters. These alloys adsorb tritium in any of its forms at one temperature and at a higher temperature release it as a gas. The system consists of four on-line getters and heaters, two ion chamber detectors, two collection getters, and two guard getters. When the incoming gas stream is valved through the on-line getters, 99.9% of it is adsorbed and the remainder continues to the guard getter where traces of tritium not collected earlier are adsorbed. The inert gas stream then exits the system to the decay chamber. Once the on-line getter has collected tritium for a predetermined time, it is valved off and the next on-line getter is valved on. Simultaneously, the first getter is heated and a pure helium purge is employed to carry the tritium from the getter. The tritium loaded gas stream is then routed through an ion chamber which measures the tritium activity. The ion chamber effluent passes through a collection getter that readsorbs the tritium and is removable from the system once it is loaded and is then replaced with a clean getter. Prior to removal of the collection getter, the system switches to a parallel collection getter. The effluent from the collection getter passes through a guard getter to remove traces of tritium prior to exiting the system. The tritium loaded collection getter, once removed, is analyzed by liquid scintillation techniques. The entire sequence is under computer control except for the removal and analysis of the collection getter. 7 figs.

  8. Tritium monitor and collection system

    DOE Patents [OSTI]

    Bourne, Gary L. (Idaho Falls, ID); Meikrantz, David H. (Idaho Falls, ID); Ely, Walter E. (Los Alamos, NM); Tuggle, Dale G. (Los Alamos, NM); Grafwallner, Ervin G. (Arco, ID); Wickham, Keith L. (Idaho Falls, ID); Maltrud, Herman R. (Los Alamos, NM); Baker, John D. (Blackfoot, ID)

    1992-01-01

    This system measures tritium on-line and collects tritium from a flowing inert gas stream. It separates the tritium from other non-hydrogen isotope contaminating gases, whether radioactive or not. The collecting portion of the system is constructed of various zirconium alloys called getters. These alloys adsorb tritium in any of its forms at one temperature and at a higher temperature release it as a gas. The system consists of four on-line getters and heaters, two ion chamber detectors, two collection getters, and two guard getters. When the incoming gas stream is valved through the on-line getters, 99.9% of it is adsorbed and the remainder continues to the guard getter where traces of tritium not collected earlier are adsorbed. The inert gas stream then exits the system to the decay chamber. Once the on-line getter has collected tritium for a predetermined time, it is valved off and the next on-line getter is valved on. Simultaneously, the first getter is heated and a pure helium purge is employed to carry the tritium from the getter. The tritium loaded gas stream is then routed through an ion chamber which measures the tritium activity. The ion chamber effluent passes through a collection getter that readsorbs the tritium and is removable from the system once it is loaded and is then replaced with a clean getter. Prior to removal of the collection getter, the system switches to a parallel collection getter. The effluent from the collection getter passes through a guard getter to remove traces of tritium prior to exiting the system. The tritium loaded collection getter, once removed, is analyzed by liquid scintillation techniques. The entire sequence is under computer control except for the removal and analysis of the collection getter.

  9. Sample collection system for gel electrophoresis

    DOE Patents [OSTI]

    Olivares, Jose A.; Stark, Peter C.; Dunbar, John M.; Hill, Karen K.; Kuske, Cheryl R.; Roybal, Gustavo

    2004-09-21

    An automatic sample collection system for use with an electrophoretic slab gel system is presented. The collection system can be used with a slab gel have one or more lanes. A detector is used to detect particle bands on the slab gel within a detection zone. Such detectors may use a laser to excite fluorescently labeled particles. The fluorescent light emitted from the excited particles is transmitted to low-level light detection electronics. Upon the detection of a particle of interest within the detection zone, a syringe pump is activated, sending a stream of buffer solution across the lane of the slab gel. The buffer solution collects the sample of interest and carries it through a collection port into a sample collection vial.

  10. Reduction of COD in leachate from a hazardous waste landfill adjacent to a coke-making facility

    SciTech Connect (OSTI)

    Banerjee, K.; O`Toole, T.J.

    1995-12-01

    A hazardous waste landfill adjacent to a coke manufacturing facility was in operation between July 1990 and December 1991. A system was constructed to collect and treat the leachate from the landfill prior to discharge to the river. Occasionally, the discharge from the treatment facility exceeded the permit limitations for Chemical Oxygen Demand (COD), Biochemical Oxygen Demand (BOD), and Total Organic Carbon (TOC). The objectives of this study were to determine treatment methods which would enable compliance with the applicable discharge limits; to establish the desired operating conditions of the process; and to investigate the effect of various parameters such as pH, catalyst dosage, and reaction time on the COD destruction efficiency. The characteristics of the landfill leachate in question were significantly variable in terms of chemical composition. A review of the influent quality data suggests that the COD concentration ranges between 80 and 390 mg/l. The oxidation processes using Fenton`s reagent or a combination of UV/hydrogen peroxide/catalyst are capable of reducing the COD concentration of the leachate below the discharge limitation of 35 mg/l. The estimated capital cost associated with the Fenton`s reagent process is approximately $525,000, and the annual operating and maintenance cost is $560,000. The estimated capital cost for the UV/hydrogen peroxide/catalyst treatment system is $565,000. The annual operating and maintenance cost of this process would be approximately $430,000.

  11. Greenhouse gas emissions from landfill leachate treatment plants: A comparison of young and aged landfill

    SciTech Connect (OSTI)

    Wang, Xiaojun; Jia, Mingsheng; Chen, Xiaohai; Xu, Ying; Lin, Xiangyu; Kao, Chih Ming; Chen, Shaohua

    2014-07-15

    Highlights: • Young and aged leachate works accounted for 89.1% and 10.9% of 33.35 Gg CO{sub 2} yr{sup −1}. • Fresh leachate owned extremely low ORP and high organic matter content. • Strong CH{sub 4} emissions occurred in the fresh leachate ponds, but small in the aged. • N{sub 2}O emissions became dominant in the treatment units of both systems. • 8.45–11.9% of nitrogen was removed as the form of N{sub 2}O under steady-state. - Abstract: With limited assessment, leachate treatment of a specified landfill is considered to be a significant source of greenhouse gas (GHG) emissions. In our study, the cumulative GHG emitted from the storage ponds and process configurations that manage fresh or aged landfill leachate were investigated. Our results showed that strong CH{sub 4} emissions were observed from the fresh leachate storage pond, with the fluxes values (2219–26,489 mg C m{sup −2} h{sup −1}) extremely higher than those of N{sub 2}O (0.028–0.41 mg N m{sup −2} h{sup −1}). In contrast, the emission values for both CH{sub 4} and N{sub 2}O were low for the aged leachate tank. N{sub 2}O emissions became dominant once the leachate entered the treatment plants of both systems, accounting for 8–12% of the removal of N-species gases. Per capita, the N{sub 2}O emission based on both leachate treatment systems was estimated to be 7.99 g N{sub 2}O–N capita{sup −1} yr{sup −1}. An increase of 80% in N{sub 2}O emissions was observed when the bioreactor pH decreased by approximately 1 pH unit. The vast majority of carbon was removed in the form of CO{sub 2}, with a small portion as CH{sub 4} (<0.3%) during both treatment processes. The cumulative GHG emissions for fresh leachate storage ponds, fresh leachate treatment system and aged leachate treatment system were 19.10, 10.62 and 3.63 Gg CO{sub 2} eq yr{sup −1}, respectively, for a total that could be transformed to 9.09 kg CO{sub 2} eq capita{sup −1} yr{sup −1}.

  12. Global garbage collection for distributed heap storage systems

    SciTech Connect (OSTI)

    Ali, K.A.M.; Haridi, S.

    1986-10-01

    The authors present a garbage-collection algorithm, suitable for loosely-coupled multi-processor systems, in which the processing elements (PEs) share only the communication medium. The algorithm is global, i.e., it involves all the PEs in the system. It allows space compaction, and it uses a system-wide marking phase to mark all accessible objects where a combination of parallel breadth-first/depth-first strategies is used for tracing the object-graphs according to a decentralized credit mechanism that regulates the number of garbage collections messages in the system. The credit mechanism is crucial for determining the space requirement of the garbage-collection messages. Also a variation of this algorithm is presented for systems with high locality of reference. It allows each PE to perform first its local garbage collection and only invokes the global garbage collection when the freed space by the local collector is insufficient.

  13. Nitrogen management in landfill leachate: Application of SHARON, ANAMMOX and combined SHARON-ANAMMOX process

    SciTech Connect (OSTI)

    Sri Shalini, S.; Joseph, Kurian

    2012-12-15

    Highlights: Black-Right-Pointing-Pointer Significant research on ammonia removal from leachate by SHARON and ANAMMOX process. Black-Right-Pointing-Pointer Operational parameters, microbiology, biochemistry and application of the process. Black-Right-Pointing-Pointer SHARON-ANAMMOX process for leachate a new research and this paper gives wide facts. Black-Right-Pointing-Pointer Cost-effective process, alternative to existing technologies for leachate treatment. Black-Right-Pointing-Pointer Address the issues and operational conditions for application in leachate treatment. - Abstract: In today's context of waste management, landfilling of Municipal Solid Waste (MSW) is considered to be one of the standard practices worldwide. Leachate generated from municipal landfills has become a great threat to the surroundings as it contains high concentration of organics, ammonia and other toxic pollutants. Emphasis has to be placed on the removal of ammonia nitrogen in particular, derived from the nitrogen content of the MSW and it is a long term pollution problem in landfills which determines when the landfill can be considered stable. Several biological processes are available for the removal of ammonia but novel processes such as the Single Reactor System for High Activity Ammonia Removal over Nitrite (SHARON) and Anaerobic Ammonium Oxidation (ANAMMOX) process have great potential and several advantages over conventional processes. The combined SHARON-ANAMMOX process for municipal landfill leachate treatment is a new, innovative and significant approach that requires more research to identify and solve critical issues. This review addresses the operational parameters, microbiology, biochemistry and application of both the processes to remove ammonia from leachate.

  14. Electrical Collection and Transmission Systems for Offshore Wind Power: Preprint

    SciTech Connect (OSTI)

    Green, J.; Bowen, A.; Fingersh, L.J.; Wan, Y.

    2007-03-01

    The electrical systems needed for offshore wind farms to collect power from wind turbines--and transmit it to shore--will be a significant cost element of these systems. This paper describes the development of a simplified model of the cost and performance of such systems.

  15. Modcopter: Prompt, Precise Aerial Sample Collection Using Unmanned Systems

    Office of Scientific and Technical Information (OSTI)

    (Technical Report) | SciTech Connect Modcopter: Prompt, Precise Aerial Sample Collection Using Unmanned Systems Citation Details In-Document Search Title: Modcopter: Prompt, Precise Aerial Sample Collection Using Unmanned Systems Authors: Curtis, Aaron [1] ; Elliott, James [2] ; Ronquest, Michael [3] ; Mascarenas, David D. [3] ; Kendrick, David T. [3] ; Lakis, Rollin E. [3] + Show Author Affiliations NM Tech NC State Los Alamos National Laboratory Publication Date: 2013-06-25 OSTI

  16. MODCOPTER: Prompt, Precise Aerial Sample Collection Using Unmanned Systems

    Office of Scientific and Technical Information (OSTI)

    (Technical Report) | SciTech Connect MODCOPTER: Prompt, Precise Aerial Sample Collection Using Unmanned Systems Citation Details In-Document Search Title: MODCOPTER: Prompt, Precise Aerial Sample Collection Using Unmanned Systems Authors: Mascarenas, David D. [1] ; Curtis, Aaron [2] ; Elliott, James [3] ; Ronquest, Michael [1] ; Kendrick, David T. [1] ; Lakis, Rollin E. [1] + Show Author Affiliations Los Alamos National Laboratory New Mexico Tech North Carolina State Publication Date:

  17. MODCOPTER: Prompt, Precise Aerial Sample Collection Using Unmanned Systems

    Office of Scientific and Technical Information (OSTI)

    (Technical Report) | SciTech Connect MODCOPTER: Prompt, Precise Aerial Sample Collection Using Unmanned Systems Citation Details In-Document Search Title: MODCOPTER: Prompt, Precise Aerial Sample Collection Using Unmanned Systems × You are accessing a document from the Department of Energy's (DOE) SciTech Connect. This site is a product of DOE's Office of Scientific and Technical Information (OSTI) and is provided as a public service. Visit OSTI to utilize additional information resources

  18. Collective behaviors of the Casimir force in microelectromechanical systems

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    (Technical Report) | SciTech Connect Collective behaviors of the Casimir force in microelectromechanical systems Citation Details In-Document Search Title: Collective behaviors of the Casimir force in microelectromechanical systems Our goal was to explore the strong dependence of the Casimir force on the shape of the interacting bodies. We made significant progress and measured the Casimir force on silicon surface with rectangular corrugation and showed that the results agree with

  19. Parallel garbage collection on a virtual memory system

    SciTech Connect (OSTI)

    Abraham, S.G.; Patel, J.H.

    1987-01-01

    Since most artificial intelligence applications are programmed in list processing languages, it is important to design architectures to support efficient garbage collection. This paper presents an architecture and an associated algorithm for parallel garbage collection on a virtual memory system. All the previously proposed parallel algorithms attempt to collect cells released by the list processor during the garbage collection cycle. We do not attempt to collect such cells. As a consequence, the list processor incurs little overhead in the proposed scheme, since it need not synchronize with the collector. Most parallel algorithms are designed for shared memory machines which have certain implicit synchronization functions on variable access. The proposed algorithm is designed for virtual memory systems where both the list processor and the garbage collector have private memories. The enforcement of coherence between the two private memories can be expensive and is not necessary in our scheme. 15 refs., 3 figs.

  20. Sandia National Labs: PCNSC: Research: Collective Hierarchical Systems

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Collective Hierarchical Systems: Developing life-emulating technologies by exploiting the physics of far-from-equilibrium, self-assembling systems What is it? We want to establish the Physical, Chemical and Nano Sciences Center and Sandia National Laboratories as major players in developing the interdisciplinary science of complex, far-from-equilibrium, self-assembling systems. These are systems that self-assemble highly organized states dynamically, across multiple length scales, through the

  1. Periodicals collection management using a decision support system

    SciTech Connect (OSTI)

    Compton, M.L.; Moser, E.C.

    1993-12-31

    Sandia National Laboratories is a multiprogram national laboratory established in 1949. The Library currently uses DOBIS for its automated system, including the Periodicals Control function for periodical check-in. DOBIS performs processing and control functions adequately, but could not meet our reporting needs. Therefore the Library`s Periodicals Decision Team decided that they needed another ``system`` for collection management. A Periodicals Decision Support System was created using information downloaded from DOBIS and uploaded into dBASE IV. The Periodical Decision Support System functions as an information-processing system that has aided us in making collection management decisions for periodicals. It certainly allows us to do interactive ad-hoc analysis; although there are no modeling tools currently incorporated in the system. We hope that these modeling tools will come later. We have been gathering information and developing needed reports to achieve this goal.

  2. Hand held data collection and monitoring system for nuclear facilities

    DOE Patents [OSTI]

    Brayton, Darryl D.; Scharold, Paul G.; Thornton, Michael W.; Marquez, Diana L.

    1999-01-01

    Apparatus and method is disclosed for a data collection and monitoring system that utilizes a pen based hand held computer unit which has contained therein interaction software that allows the user to review maintenance procedures, collect data, compare data with historical trends and safety limits, and input new information at various collection sites. The system has a means to allow automatic transfer of the collected data to a main computer data base for further review, reporting, and distribution purposes and uploading updated collection and maintenance procedures. The hand held computer has a running to-do list so sample collection and other general tasks, such as housekeeping are automatically scheduled for timely completion. A done list helps users to keep track of all completed tasks. The built-in check list assures that work process will meet the applicable processes and procedures. Users can hand write comments or drawings with an electronic pen that allows the users to directly interface information on the screen.

  3. Hand held data collection and monitoring system for nuclear facilities

    DOE Patents [OSTI]

    Brayton, D.D.; Scharold, P.G.; Thornton, M.W.; Marquez, D.L.

    1999-01-26

    Apparatus and method is disclosed for a data collection and monitoring system that utilizes a pen based hand held computer unit which has contained therein interaction software that allows the user to review maintenance procedures, collect data, compare data with historical trends and safety limits, and input new information at various collection sites. The system has a means to allow automatic transfer of the collected data to a main computer data base for further review, reporting, and distribution purposes and uploading updated collection and maintenance procedures. The hand held computer has a running to-do list so sample collection and other general tasks, such as housekeeping are automatically scheduled for timely completion. A done list helps users to keep track of all completed tasks. The built-in check list assures that work process will meet the applicable processes and procedures. Users can hand write comments or drawings with an electronic pen that allows the users to directly interface information on the screen. 15 figs.

  4. Secondary ion collection and transport system for ion microprobe

    DOE Patents [OSTI]

    Ward, James W. (Canoga Park, CA); Schlanger, Herbert (Simi Valley, CA); McNulty, Jr., Hugh (Santa Monica, CA); Parker, Norman W. (Camarillo, CA)

    1985-01-01

    A secondary ion collection and transport system, for use with an ion microprobe, which is very compact and occupies only a small working distance, thereby enabling the primary ion beam to have a short focal length and high resolution. Ions sputtered from the target surface by the primary beam's impact are collected between two arcuate members having radii of curvature and applied voltages that cause only ions within a specified energy band to be collected. The collected ions are accelerated and focused in a transport section consisting of a plurality of spaced conductive members which are coaxial with and distributed along the desired ion path. Relatively high voltages are applied to alternate transport sections to produce accelerating electric fields sufficient to transport the ions through the section to an ion mass analyzer, while lower voltages are applied to the other transport sections to focus the ions and bring their velocity to a level compatible with the analyzing apparatus.

  5. Greenhouse gas emissions from landfill leachate treatment plants: A

    Office of Scientific and Technical Information (OSTI)

    comparison of young and aged landfill (Journal Article) | SciTech Connect Greenhouse gas emissions from landfill leachate treatment plants: A comparison of young and aged landfill Citation Details In-Document Search Title: Greenhouse gas emissions from landfill leachate treatment plants: A comparison of young and aged landfill Highlights: * Young and aged leachate works accounted for 89.1% and 10.9% of 33.35 Gg CO{sub 2} yr{sup -1}. * Fresh leachate owned extremely low ORP and high organic

  6. Greenhouse gas emissions from landfill leachate treatment plants...

    Office of Scientific and Technical Information (OSTI)

    ... Subject: 54 ENVIRONMENTAL SCIENCES; 12 MANAGEMENT OF RADIOACTIVE WASTES, AND NON-RADIOACTIVE WASTES FROM NUCLEAR FACILITIES; AGING; CARBON DIOXIDE; GREENHOUSE GASES; LEACHATES; ...

  7. Garbage collection for functional languages in a distributed system

    SciTech Connect (OSTI)

    Eckart, J.D.

    1987-01-01

    Garbage collection is a helpful facility provided by many applicative languages such as Prolog, SISAL, FP, and Lisp. While these, and other, languages provide easy recognition of actions that may be executed in parallel, the garbage-collection algorithms used for single-machine environments become significantly more inefficient in multi-machine environments. Thus, in order to make effective use of these languages, more-efficient algorithms for collecting inter-machine structures is needed. Reference marking is the algorithm developed to meet these needs. It takes advantage of the semantics of applicative languages allowing each parallel action to be responsible for collecting any discarded structures it was responsible for creating. Simulation results comparing the performance of reference marking with other distributed garbage-collection algorithms are given. A variety of problem types and sizes are examined to determine the effects of particular styles of computation on each of the garbage-collection algorithms. The results gathered demonstrate the usefulness of the reference-marking algorithm in both uni- and multi-machine systems.

  8. Leachate concentrations from water leach and column leach tests on fly ash-stabilized soils

    SciTech Connect (OSTI)

    Bin-Shafique, S.; Benson, C.H.; Edil, T.B.; Hwang, K.

    2006-01-15

    Batch water leaching tests (WLTs) and column leaching tests (CLTs) were conducted on coal-combustion fly ashes, soil, and soil-fly ash mixtures to characterize leaching of Cd, Cr, Se, and Ag. The concentrations of these metals were also measured in the field at two sites where soft fine-grained soils were mechanically stabilized with fly ash. Concentrations in leachate from the WLTs on soil-fly ash mixtures are different from those on fly ash alone and cannot be accurately estimated based on linear dilution calculations using concentrations from WLTs on fly ash alone. The concentration varies nonlinearly with fly ash content due to the variation in pH with fly ash content. Leachate concentrations are low when the pH of the leachate or the cation exchange capacity (CEC) of the soil is high. Initial concentrations from CLTs are higher than concentrations from WLTs due to differences in solid-liquid ratio, pH, and solid-liquid contact. However, both exhibit similar trends with fly ash content, leachate pH, and soil properties. Scaling factors can be applied to WLT concentrations (50 for Ag and Cd, 10 for Cr and Se) to estimate initial concentrations for CLTs. Concentrations in leachate collected from the field sites were generally similar or slightly lower than concentrations measured in CLTs on the same materials. Thus, CLTs appear to provide a good indication of conditions that occur in the field provided that the test conditions mimic the field conditions. In addition, initial concentrations in the field can be conservatively estimated from WLT concentrations using the aforementioned scaling factors provided that the pH of the infiltrating water is near neutral.

  9. Solar-thermal-energy collection/storage-pond system

    DOE Patents [OSTI]

    Blahnik, D.E.

    1982-03-25

    A solar thermal energy collection and storage system is disclosed. Water is contained, and the water surface is exposed directly to the sun. The central part of an impermeable membrane is positioned below the water's surface and above its bottom with a first side of the membrane pointing generally upward in its central portion. The perimeter part of the membrane is placed to create a watertight boundary separating the water into a first volume which is directly exposable to the sun and which touches the membranes first side, and a second volumn which touches the membranes second side. A salt is dissolved in the first water volume.

  10. Hybrid Plasma Reactor/Filter for Transportable Collective Protection Systems

    SciTech Connect (OSTI)

    Josephson, Gary B.; Tonkyn, Russell G.; Frye, J. G.; Riley, Brian J.; Rappe, Kenneth G.

    2011-04-06

    Pacific Northwest National Laboratory (PNNL) has performed an assessment of a Hybrid Plasma/Filter system as an alternative to conventional methods for collective protection. The key premise of the hybrid system is to couple a nonthermal plasma (NTP) reactor with reactive adsorption to provide a broader envelope of protection than can be provided through a single-solution approach. The first step uses highly reactive species (e.g. oxygen radicals, hydroxyl radicals, etc.) created in a nonthermal plasma (NTP) reactor to destroy the majority (~75% - 90%) of an incoming threat. Following the NTP reactor an O3 reactor/filter uses the O3 created in the NTP reactor to further destroy the remaining organic materials. This report summarizes the laboratory development of the Hybrid Plasma Reactor/Filter to protect against a worst-case simulant, methyl bromide (CH3Br), and presents a preliminary engineering assessment of the technology to Joint Expeditionary Collective Protection performance specifications for chemical vapor air purification technologies.

  11. Data Collection and Analyses of the CHP System at Eastern Maine...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Data Collection and Analyses of the CHP System at Eastern Maine Medical Center - Final Report, June 2008 Data Collection and Analyses of the CHP System at Eastern Maine Medical ...

  12. Mutagenicity and genotoxicity of coal fly ash water leachate

    SciTech Connect (OSTI)

    Chakraborty, R.; Mukherjee, A.

    2009-03-15

    Fly ash is a by-product of coal-fired electricity generation plants. The prevalent practice of disposal is as slurry of ash and water to storage or ash ponds located near power stations. This has lain to waste thousands of hectares of land all over the world. Since leaching is often the cause of off-site contamination and pathway of introduction into the human environment, a study on the genotoxic effects of fly ash leachate is essential. Leachate prepared from the fly ash sample was analyzed for metal content, and tested for mutagenicity and genotoxicity. Analyses of metals show predominance of the metals - sodium, silicon, potassium, calcium, magnesium, iron, manganese, zinc, and sulphate. The Ames Salmonella mutagenicity assay, a short-term bacterial reverse mutation assay, was conducted on two-tester strains of Salmonella typhimurium strains TA97a and TA102. For genotoxicity, the alkaline version of comet assay on fly ash leachate was carried in vitro on human blood cells and in vivo on Nicotiana plants. The leachate was directly mutagenic and induced significantconcentration-dependent increases in DNA damage in whole blood cells, lymphocytes, and in Nicotiana plants. The comet parameters show increases in tail DNA percentage (%), tail length (mu m), and olive tail moment (arbitrary units). Our results indicate that leachate from fly ash dumpsites has the genotoxic potential and may lead to adverse effects on vegetation and on the health of exposed human populations.

  13. Continuous remote unattended monitoring for safeguards data collection systems

    SciTech Connect (OSTI)

    Klosterbuer, S.F.; Halbig, J.K.; Harker, W.C.; Menlove, H.O.; Painter, J.A.; Stewart, J.E.

    1994-02-01

    To meet increased inspection requirements, unattended and remote monitoring systems have been developed and installed in several large facilities to perform safeguards functions. These unattended monitoring systems are based on instruments originally developed for traditional safeguards and the domestic nuclear industry to nondestructively assay nuclear materials. Through specialized measurement procedures, these instruments have been adapted to be unattended monitors. This paper defines the parts of these unattended monitoring systems, describes the systems that have been installed in the field and their status, and discusses future trends for unattended systems.

  14. Environmental sustainability comparison of a hypothetical pneumatic waste collection system and a door-to-door system

    SciTech Connect (OSTI)

    Punkkinen, Henna; Merta, Elina; Teerioja, Nea; Moliis, Katja; Kuvaja, Eveliina

    2012-10-15

    Highlights: Black-Right-Pointing-Pointer We compare the environmental sustainability of two MSW collection systems. Black-Right-Pointing-Pointer We evaluate pneumatic and door-to-door collection systems. Black-Right-Pointing-Pointer The greenhouse gas emissions of pneumatic collection are around three times higher. Black-Right-Pointing-Pointer System components are decisive but assumptions on electricity use are also important. Black-Right-Pointing-Pointer Pneumatic collection could provide other benefits over door-to-door system. - Abstract: Waste collection is one of the life cycle phases that influence the environmental sustainability of waste management. Pneumatic waste collection systems represent a new way of arranging waste collection in densely populated urban areas. However, limited information is available on the environmental impacts of this system. In this study, we compare the environmental sustainability of conventional door-to-door waste collection with its hypothetical pneumatic alternative. Furthermore, we analyse whether the size of the hypothetical pneumatic system, or the number of waste fractions included, have an impact on the results. Environmental loads are calculated for a hypothetical pneumatic waste collection system modelled on an existing dense urban area in Helsinki, Finland, and the results are compared to those of the prevailing, container-based, door-to-door waste collection system. The evaluation method used is the life-cycle inventory (LCI). In this study, we report the atmospheric emissions of greenhouse gases (GHG), SO{sub 2} and NO{sub x}. The results indicate that replacing the prevailing system with stationary pneumatic waste collection in an existing urban infrastructure would increase total air emissions. Locally, in the waste collection area, emissions would nonetheless diminish, as collection traffic decreases. While the electricity consumption of the hypothetical pneumatic system and the origin of electricity have a significant bearing on the results, emissions due to manufacturing the system's components prove decisive.

  15. High-speed and high-fidelity system and method for collecting network traffic

    DOE Patents [OSTI]

    Weigle, Eric H. (Los Alamos, NM)

    2010-08-24

    A system is provided for the high-speed and high-fidelity collection of network traffic. The system can collect traffic at gigabit-per-second (Gbps) speeds, scale to terabit-per-second (Tbps) speeds, and support additional functions such as real-time network intrusion detection. The present system uses a dedicated operating system for traffic collection to maximize efficiency, scalability, and performance. A scalable infrastructure and apparatus for the present system is provided by splitting the work performed on one host onto multiple hosts. The present system simultaneously addresses the issues of scalability, performance, cost, and adaptability with respect to network monitoring, collection, and other network tasks. In addition to high-speed and high-fidelity network collection, the present system provides a flexible infrastructure to perform virtually any function at high speeds such as real-time network intrusion detection and wide-area network emulation for research purposes.

  16. Collective operations in a file system based execution model

    DOE Patents [OSTI]

    Shinde, Pravin; Van Hensbergen, Eric

    2013-02-12

    A mechanism is provided for group communications using a MULTI-PIPE synthetic file system. A master application creates a multi-pipe synthetic file in the MULTI-PIPE synthetic file system, the master application indicating a multi-pipe operation to be performed. The master application then writes a header-control block of the multi-pipe synthetic file specifying at least one of a multi-pipe synthetic file system name, a message type, a message size, a specific destination, or a specification of the multi-pipe operation. Any other application participating in the group communications then opens the same multi-pipe synthetic file. A MULTI-PIPE file system module then implements the multi-pipe operation as identified by the master application. The master application and the other applications then either read or write operation messages to the multi-pipe synthetic file and the MULTI-PIPE synthetic file system module performs appropriate actions.

  17. Collective operations in a file system based execution model

    DOE Patents [OSTI]

    Shinde, Pravin; Van Hensbergen, Eric

    2013-02-19

    A mechanism is provided for group communications using a MULTI-PIPE synthetic file system. A master application creates a multi-pipe synthetic file in the MULTI-PIPE synthetic file system, the master application indicating a multi-pipe operation to be performed. The master application then writes a header-control block of the multi-pipe synthetic file specifying at least one of a multi-pipe synthetic file system name, a message type, a message size, a specific destination, or a specification of the multi-pipe operation. Any other application participating in the group communications then opens the same multi-pipe synthetic file. A MULTI-PIPE file system module then implements the multi-pipe operation as identified by the master application. The master application and the other applications then either read or write operation messages to the multi-pipe synthetic file and the MULTI-PIPE synthetic file system module performs appropriate actions.

  18. Shunt attachment and method for interfacing current collection systems

    DOE Patents [OSTI]

    Denney, P.E.; Iyer, N.C.; Hannan, W.F. III.

    1992-12-08

    A composite brush to shunt attachment wherein a volatile component of a composite but mostly metallic brush, used for current collection purposes, does not upon welding or brazing, adversely affect the formation of the interfacial bond with a conductive shunt which carries the current from the zone of the brush. The brush to shunt attachment for a brush material of copper-graphite composite and a shunt of copper, or substituting silver for copper as an alternative, is made through a hot isostatic pressing (HIP). The HIP process includes applying high pressure and temperature simultaneously at the brush to shunt interface, after it has been isolated or canned in a metal casing in which the air adjacent to the interface has been evacuated and the interfacial area has been sealed before the application of pressure and temperature. 6 figs.

  19. Shunt attachment and method for interfacing current collection systems

    DOE Patents [OSTI]

    Denney, Paul E. (State College, PA); Iyer, Natraj C. (Columbia, SC); Hannan, III, William F. (Monroeville Boro, PA)

    1992-01-01

    A composite brush to shunt attachment wherein a volatile component of a composite but mostly metallic brush, used for current collection purposes, does not upon welding or brazing, adversely affect the formation of the interfacial bond with a conductive shunt which carries the current from the zone of the brush. The brush to shunt attachment for a brush material of copper-graphite composite and a shunt of copper, or substituting silver for copper as an alternative, is made through a hot isostatic pressing (HIP). The HIP process includes applying high pressure and temperature simultaneously at the brush to shunt interface, after it has been isolated or canned in a metal casing in which the air adjacent to the interface has been evacuated and the interfacial area has been sealed before the application of pressure and temperature.

  20. Multichannel microscale system for high throughput preparative separation with comprehensive collection and analysis

    DOE Patents [OSTI]

    Karger, Barry L.; Kotler, Lev; Foret, Frantisek; Minarik, Marek; Kleparnik, Karel

    2003-12-09

    A modular multiple lane or capillary electrophoresis (chromatography) system that permits automated parallel separation and comprehensive collection of all fractions from samples in all lanes or columns, with the option of further on-line automated sample fraction analysis, is disclosed. Preferably, fractions are collected in a multi-well fraction collection unit, or plate (40). The multi-well collection plate (40) is preferably made of a solvent permeable gel, most preferably a hydrophilic, polymeric gel such as agarose or cross-linked polyacrylamide.

  1. West Valley low-level radioactive waste site revisited: Microbiological analysis of leachates

    SciTech Connect (OSTI)

    Gillow, J.B.; Francis, A.J.

    1990-10-01

    The abundance and types of microorganisms in leachate samples from the West Valley low-level radioactive waste disposal site were enumerated. This study was undertaken in support of the study conducted by Ecology and Environment, Inc., to assess the extent of radioactive gas emissions from the site. Total aerobic and anaerobic bacteria were enumerated as colony forming units (CFU) by dilution agar plate technique, and denitrifiers, sulfate-reducers and methanogens by the most probable number technique (MPN). Of the three trenches 3, 9, and 11 sampled, trench 11 contained the most number of organisms in the leachate. Concentrations of carbon-14 and tritium were highest in trench 11 leachate. Populations of aerobes and anaerobes in trench 9 leachate were one order of magnitude less than in trench 11 leachate while the methanogens were three orders of magnitude greater than in trench 11 leachate. The methane content from trench 9 was high due to the presence of a large number of methanogens; the gas in this trench also contained the most radioactivity. Trench 3 leachate contained the least number of microorganisms. Comparison of microbial populations in leachates sampled from trenches 3 and 9 during October 1978 and 1989 showed differences in the total number of microbial types. Variations in populations of the different types of organisms in the leachate reflect the changing nutrient conditions in the trenches. 14 refs., 3 figs., 4 tabs.

  2. Levelized life-cycle costs for four residue-collection systems and four gas-production systems

    SciTech Connect (OSTI)

    Thayer, G.R.; Rood, P.L.; Williamson, K.D. Jr.; Rollett, H.

    1983-01-01

    Technology characterizations and life-cycle costs were obtained for four residue-collection systems and four gas-production systems. All costs are in constant 1981 dollars. The residue-collection systems were cornstover collection, wheat-straw collection, soybean-residue collection, and wood chips from forest residue. The life-cycle costs ranged from $19/ton for cornstover collection to $56/ton for wood chips from forest residues. The gas-production systems were low-Btu gas from a farm-size gasifier, solar flash pyrolysis of biomass, methane from seaweed farms, and hydrogen production from bacteria. Life-cycle costs ranged from $3.3/10/sup 6/ Btu for solar flash pyrolysis of biomass to $9.6/10/sup 6/ Btu for hydrogen from bacteria. Sensitivity studies were also performed for each system. The sensitivity studies indicated that fertilizer replacement costs were the dominate costs for the farm-residue collection, while residue yield was most important for the wood residue. Feedstock costs were most important for the flash pyrolysis. Yields and capital costs are most important for the seaweed farm and the hydrogen from bacteria system.

  3. Feature test report for the Small Debris Collection and Packaging System

    SciTech Connect (OSTI)

    Brisbin, S.A.

    1995-03-17

    The Spent Nuclear Fuel Equipment Engineering group performed feature testing of the Small Debris Collection and Packaging System (SDCPS) in the 305 Cold Test Facility from January 30, 1995, to February 1, 1995. Feature testing of the Small Debris Collection and Packaging System (SDCPS) was performed for the following reasons: To assess the feasibility of using ``drop-out`` vessels to collect small debris (<2.5 cm) in MK-II fuel canisters while transferring sludge to the Weasel Pit. To evaluate system performance under conditions similar to those in the K-Basins (e.g. submerged under 4.9 meters of water and operated with long handled tools) while using a surrogate sludge mixed with debris. To determine if canister weight could be used to predict the volume of sludge and/or debris contained within the canisters during system operation.

  4. Groundwater and Leachate Monitoring and Sampling at ERDF, CY 2010

    SciTech Connect (OSTI)

    Weiss, R. L.; Lawrence, B. L.

    2011-06-09

    The purpose of this annual monitoring report is to evaluate the conditions of and identify trends for groundwater beneath the ERDF and report leachate results in fulfillment of the requirements specified in the ERDF ROD2 and the ERDF Amended ROD (EPA 1999). The overall objective of the groundwater monitoring program is to determine whether ERDF has impacted the groundwater. This objective is complicated by the fact that the ERDF is situated downgradient of the numerous groundwater contamination plumes originating from the 200 West Area.

  5. Implementing asyncronous collective operations in a multi-node processing system

    DOE Patents [OSTI]

    Chen, Dong; Eisley, Noel A.; Heidelberger, Philip; Kumar, Sameer; Salapura, Valentina; Steinmacher-Burow, Burkhard

    2014-07-08

    A method, system, and computer program product are disclosed for implementing an asynchronous collective operation in a multi-node data processing system. In one embodiment, the method comprises sending data to a plurality of nodes in the data processing system, broadcasting a remote get to the plurality of nodes, and using this remote get to implement asynchronous collective operations on the data by the plurality of nodes. In one embodiment, each of the nodes performs only one task in the asynchronous operations, and each nodes sets up a base address table with an entry for a base address of a memory buffer associated with said each node. In another embodiment, each of the nodes performs a plurality of tasks in said collective operations, and each task of each node sets up a base address table with an entry for a base address of a memory buffer associated with the task.

  6. Collective many-body van der Waals interactions in molecular systems

    Office of Scientific and Technical Information (OSTI)

    (Journal Article) | SciTech Connect Journal Article: Collective many-body van der Waals interactions in molecular systems Citation Details In-Document Search Title: Collective many-body van der Waals interactions in molecular systems Authors: DeStasio, Jr., R.A. ; von Lilienfeld, O.A. ; Tkatchenko, A. [1] + Show Author Affiliations (LCF) [LCF Publication Date: 2012-09-11 OSTI Identifier: 1132743 Report Number(s): ANL/LCF/JA-72880 Journal ID: 0027-8424 DOE Contract Number: DE-AC02-06CH11357

  7. Data Collection and Analyses of the CHP System at Eastern Maine Medical

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Center - Final Report, June 2008 | Department of Energy Data Collection and Analyses of the CHP System at Eastern Maine Medical Center - Final Report, June 2008 Data Collection and Analyses of the CHP System at Eastern Maine Medical Center - Final Report, June 2008 This 2008 report describes the Eastern Maine Medical Center's installation of a Centaur 50 gas turbine and performance data for one year from December 2006 to November 2007. The turbine has a nameplate rating of 4,570 kW and can

  8. Wind energy Computerized Maintenance Management System (CMMS) : data collection recommendations for reliability analysis.

    SciTech Connect (OSTI)

    Peters, Valerie A.; Ogilvie, Alistair B.

    2012-01-01

    This report addresses the general data requirements for reliability analysis of fielded wind turbines and other wind plant equipment. The report provides a rationale for why this data should be collected, a list of the data needed to support reliability and availability analysis, and specific data recommendations for a Computerized Maintenance Management System (CMMS) to support automated analysis. This data collection recommendations report was written by Sandia National Laboratories to address the general data requirements for reliability analysis of operating wind turbines. This report is intended to help develop a basic understanding of the data needed for reliability analysis from a Computerized Maintenance Management System (CMMS) and other data systems. The report provides a rationale for why this data should be collected, a list of the data needed to support reliability and availability analysis, and specific recommendations for a CMMS to support automated analysis. Though written for reliability analysis of wind turbines, much of the information is applicable to a wider variety of equipment and analysis and reporting needs. The 'Motivation' section of this report provides a rationale for collecting and analyzing field data for reliability analysis. The benefits of this type of effort can include increased energy delivered, decreased operating costs, enhanced preventive maintenance schedules, solutions to issues with the largest payback, and identification of early failure indicators.

  9. Experimental study of slab solar collection on the hydronic system of road

    SciTech Connect (OSTI)

    Gao, Qing; Huang, Yong; Li, Ming; Liu, Yan [Jilin University, Changchun (China); Yan, Y.Y. [University of Nottingham (United Kingdom)

    2010-12-15

    This paper studied the slab solar collection (SSC) process, which is one of the essential compositions of road hydronic ice-snow melting (HISM) system that stores solar energy in summer to melt ice and snow on the road in winter. Its aim is to find out the heat transfer characteristic of the SSC and heat collecting efficiency and the influence of pipe spacing and flow rate by experiment. As shown in experimental results, the average heat collecting capacity is about 150-250 W/m{sup 2} in natural summer condition, while the solar radiation intensity is about 300-1000 W/m{sup 2}. It is shown that the increment of fluid flow results in the increment of heat collection efficiency, while the increment of pipe spacing results in the decrement of the efficiency in experiment modes. The results show that the road slab can obtain about 30% solar heat in summertime, and the solar collection can lower the pavement temperature and reduce the insolation weathering. (author)

  10. Capacitated location of collection sites in an urban waste management system

    SciTech Connect (OSTI)

    Ghiani, Gianpaolo; Lagana, Demetrio; Manni, Emanuele; Triki, Chefi

    2012-07-15

    Urban waste management is becoming an increasingly complex task, absorbing a huge amount of resources, and having a major environmental impact. The design of a waste management system consists in various activities, and one of these is related to the location of waste collection sites. In this paper, we propose an integer programming model that helps decision makers in choosing the sites where to locate the unsorted waste collection bins in a residential town, as well as the capacities of the bins to be located at each collection site. This model helps in assessing tactical decisions through constraints that force each collection area to be capacitated enough to fit the expected waste to be directed to that area, while taking into account Quality of Service constraints from the citizens' point of view. Moreover, we propose an effective constructive heuristic approach whose aim is to provide a good solution quality in an extremely reduced computational time. Computational results on data related to the city of Nardo, in the south of Italy, show that both exact and heuristic approaches provide consistently better solutions than that currently implemented, resulting in a lower number of activated collection sites, and a lower number of bins to be used.

  11. Effect of landfill leachate organic acids on trace metal adsorption by kaolinite

    SciTech Connect (OSTI)

    Schroth, B.; Garrison, Sposito

    1997-02-01

    Hexanoic (hex) and fulvic acid (FA), representing early and later stages of landfill leachate evolution, were examined for influence on trace metal adsorption by a poorly crystallized kaolinite (KGa-2). Our experiments represented a model approach to examine possible reaction mechanisms in an environmentally important ternary metal-ligand-mineral surface system. Batch experiments were conducted in 0.01 mol kg(-1) NaClO4 at pH 3-8. Concentrations of metals (Cu, Cd, and Pb) and ligands were representative of those found typically in groundwater immediately downgradient of a landfill. The presence of FA resulted in enhancement of metal adsorption below pH 5, whereas the presence of hex produced no significant net change in metal uptake. Measured surface charge properties of KGa-2 were combined with binary and ternary system data in constructing a quantitative model of the system. The simple combination of binary system results was not effective in predicting the observed ternary system behavior. In both ternary systems, the addition of ternary surface complexes (TSCs) to the models resulted in a satisfactory fit to the data. Our work suggests the strong possibility that TSC involvement in surface reactions of natural adsorbents may be a useful concept.

  12. A Statistical Characterization of School Bus Drive Cycles Collected via Onboard Logging Systems

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ____________________________________ 2013-01-2400 Published 09/24/2013 doi:10.4271/2013-01-2400 saecomveh.saejournals.org A Statistical Characterization of School Bus Drive Cycles Collected via Onboard Logging Systems Adam Duran and Kevin Walkowicz National Renewable Energy Laboratory ABSTRACT In an effort to characterize the dynamics typical of school bus operation, National Renewable Energy Laboratory (NREL) researchers set out to gather in-use duty cycle data from school bus fleets operating

  13. Wind energy Computerized Maintenance Management System (CMMS) : data collection recommendations for reliability analysis.

    SciTech Connect (OSTI)

    Peters, Valerie A.; Ogilvie, Alistair; Veers, Paul S.

    2009-09-01

    This report addresses the general data requirements for reliability analysis of fielded wind turbines and other wind plant equipment. The report provides a list of the data needed to support reliability and availability analysis, and gives specific recommendations for a Computerized Maintenance Management System (CMMS) to support automated analysis. This data collection recommendations report was written by Sandia National Laboratories to address the general data requirements for reliability analysis of fielded wind turbines. This report is intended to help the reader develop a basic understanding of what data are needed from a Computerized Maintenance Management System (CMMS) and other data systems, for reliability analysis. The report provides: (1) a list of the data needed to support reliability and availability analysis; and (2) specific recommendations for a CMMS to support automated analysis. Though written for reliability analysis of wind turbines, much of the information is applicable to a wider variety of equipment and a wider variety of analysis and reporting needs.

  14. Scaling up logic-based truth maintenance systems via fact garbage collection

    SciTech Connect (OSTI)

    Everett, J.O.; Forbus, K.D.

    1996-12-31

    Truth maintenance systems provide caches of beliefs and inferences that support explanations and search. Traditionally, the cost of using a TMS is monotonic growth in the size of this cache. In some applications this cost is too high; for example, intelligent learning environments may require students to explore many alternatives, which leads to unacceptable performance. This paper describes an algorithm for fact garbage collection that retains the explanation-generating capabilities of a TMS while eliminating the increased storage overhead. We describe the application context that motivated this work and the properties of applications that benefit from this technique. We present the algorithm, showing how to balance the tradeoff between maintaining a useful cache and reclaiming storage, and analyze its complexity. We demonstrate that this algorithm can eliminate monotonic storage growth, thus making it more practical to field large-scale TMS-based systems.

  15. Statistical Characterization of School Bus Drive Cycles Collected via Onboard Logging Systems

    SciTech Connect (OSTI)

    Duran, A.; Walkowicz, K.

    2013-10-01

    In an effort to characterize the dynamics typical of school bus operation, National Renewable Energy Laboratory (NREL) researchers set out to gather in-use duty cycle data from school bus fleets operating across the country. Employing a combination of Isaac Instruments GPS/CAN data loggers in conjunction with existing onboard telemetric systems resulted in the capture of operating information for more than 200 individual vehicles in three geographically unique domestic locations. In total, over 1,500 individual operational route shifts from Washington, New York, and Colorado were collected. Upon completing the collection of in-use field data using either NREL-installed data acquisition devices or existing onboard telemetry systems, large-scale duty-cycle statistical analyses were performed to examine underlying vehicle dynamics trends within the data and to explore vehicle operation variations between fleet locations. Based on the results of these analyses, high, low, and average vehicle dynamics requirements were determined, resulting in the selection of representative standard chassis dynamometer test cycles for each condition. In this paper, the methodology and accompanying results of the large-scale duty-cycle statistical analysis are presented, including graphical and tabular representations of a number of relationships between key duty-cycle metrics observed within the larger data set. In addition to presenting the results of this analysis, conclusions are drawn and presented regarding potential applications of advanced vehicle technology as it relates specifically to school buses.

  16. Steam System Balancing and Tuning for Multifamily Residential Buildings in Chicagoland - Second Year of Data Collection

    SciTech Connect (OSTI)

    Choi, J.; Ludwig, P.; Brand, L.

    2013-08-01

    Steam heated buildings often suffer from uneven heating as a result of poor control of the amount of steam entering each radiator. In order to satisfy the heating load to the coldest units, other units are overheated. As a result, some tenants complain of being too hot and open their windows in the middle of winter, while others complain of being too cold and are compelled to use supplemental heat sources. Building on previous research, CNT Energy identified 10 test buildings in Chicago and conducted a study to identify best practices for the methodology, typical costs, and energy savings associated with steam system balancing. A package of common steam balancing measures was assembled and data were collected on the buildings before and after these retrofits were installed to investigate the process, challenges, and the cost effectiveness of improving steam systems through improved venting and control systems. The test buildings that received venting upgrades and new control systems showed 10.2% savings on their natural gas heating load, with a simple payback of 5.1 years. The methodologies for and findings from this study are presented in detail in this report. This report has been updated from a version published in August 2012 to include natural gas usage information from the 2012 heating season and updated natural gas savings calculations.

  17. Experimental evidence of colloids and nanoparticles presence from 25 waste leachates

    SciTech Connect (OSTI)

    Hennebert, Pierre; Avellan, Astrid; Yan, Junfang; Aguerre-Chariol, Olivier

    2013-09-15

    Highlights: This work is the first assessment of colloids in waste leachates. Analytical methods are proposed and discussed. All the waste have at least one element in colloidal form, and some elements are always colloidal. Man-made nanoparticles are observed. It can change the interpretation of leachate elemental concentration. - Abstract: The potential colloids release from a large panel of 25 solid industrial and municipal waste leachates, contaminated soil, contaminated sediments and landfill leachates was studied. Standardized leaching, cascade filtrations and measurement of element concentrations in the microfiltrate (MF) and ultrafiltrate (UF) fraction were used to easily detect colloids potentially released by waste. Precautions against CO{sub 2} capture by alkaline leachates, or bacterial re-growth in leachates from wastes containing organic matter should be taken. Most of the colloidal particles were visible by transmission electron microscopy with energy dispersion spectrometry (TEMEDS) if their elemental MF concentration is greater than 200 ?g l{sup ?1}. If the samples are dried during the preparation for microscopy, neoformation of particles can occur from the soluble part of the element. Size distribution analysis measured by photon correlation spectroscopy (PCS) were frequently unvalid, particularly due to polydispersity and/or too low concentrations in the leachates. A low sensitivity device is required, and further improvement is desirable in that field. For some waste leachates, particles had a zeta potential strong enough to remain in suspension. Mn, As, Co, Pb, Sn, Zn had always a colloidal form (MF concentration/UF concentration > 1.5) and total organic carbon (TOC), Fe, P, Ba, Cr, Cu, Ni are partly colloidal for more than half of the samples). Nearly all the micro-pollutants (As, Ba, Co, Cr, Cu, Mo, Ni, Pb, Sb, Sn, V and Zn) were found at least once in colloidal form greater than 100 ?g l{sup ?1}. In particular, the colloidal forms of Zn were always by far more concentrated than its dissolved form. The TEMEDS method showed various particles, including manufactured nanoparticles (organic polymer, TiO{sub 2}, particles with Sr, La, Ce, Nd). All the waste had at least one element detected as colloidal. The solid waste leachates contained significant amount of colloids different in elemental composition from natural ones. The majority of the elements were in colloidal form for wastes of packaging (3), a steel slag, a sludge from hydrometallurgy, composts (2), a dredged sediment (#18), an As contaminated soil and two active landfill leachates. These results showed that cascade filtration and ICP elemental analysis seems valid methods in this field, and that electronic microscopy with elemental detection allows to identify particles. Particles can be formed from dissolved elements during TEM sample preparation and cross-checking with MF and UF composition by ICP is useful. The colloidal fraction of leachate of waste seems to be a significant source term, and should be taken into account in studies of emission and transfer of contaminants in the environment. Standardized cross-filtration method could be amended for the presence of colloids in waste leachates.

  18. Laboratory measurements of contaminant attenuation of uranium mill tailings leachates by sediments and clay liners

    SciTech Connect (OSTI)

    Serne, R.J.; Peterson, S.R.; Gee, G.W.

    1983-04-01

    We discuss FY82 progress on the development of laboratory tools to aid in the prediction of migration potential of contaminants present in acidic uranium mill tailings leachate. Further, empirical data on trace metal and radionuclide migration through a clay liner are presented. Acidic uranium mill tailings solution from a Wyoming mill was percolated through a composite sediment called Morton Ranch Clay liner. These laboratory columns and subsequent sediment extraction data show: (1) As, Cr, Pb, Ag, Th and V migrate very slowly; (2) U, Cd, Ni, Zn, Fe, Mn and similar transition metals are initially immobilized during acid neutralization but later are remobilized as the tailings solution exhausts the clay liner's acid buffering capacity. Such metals remain immobilized as long as the effluent pH remains above a pH value of 4 to 4.5, but they become mobile once the effluent pH drops below this range; and (3) fractions of the Se and Mo present in the influent tailings solution are very mobile. Possible controlling mechanisms for the pH-dependent immobilization-mobilization of the trace metals are discussed. More study is required to understand the controlling mechanisms for Se and Mo and Ra for which data were not successfully collected. Using several column lengths (from 4.5 to 65 cm) and pore volume residence times (from 0.8 to 40 days) we found no significant differences in contaminant migration rates or types and extent of controlling processes. Thus, we conclude that the laboratory results may be capable of extrapolation to actual disposal site conditions.

  19. Separate collection of household food waste for anaerobic degradation - Comparison of different techniques from a systems perspective

    SciTech Connect (OSTI)

    Bernstad, A.; Cour Jansen, J. la

    2012-05-15

    Highlight: Black-Right-Pointing-Pointer Four modern and innovative systems for household food waste collection are compared. Black-Right-Pointing-Pointer Direct emissions and resource use were based on full-scale data. Black-Right-Pointing-Pointer Conservation of nutrients/energy content over the system was considered. Black-Right-Pointing-Pointer Systems with high energy/nutrient recovery are most environmentally beneficial. - Abstract: Four systems for household food waste collection are compared in relation the environmental impact categories eutrophication potential, acidification potential, global warming potential as well as energy use. Also, a hotspot analysis is performed in order to suggest improvements in each of the compared collection systems. Separate collection of household food waste in paper bags (with and without drying prior to collection) with use of kitchen grinders and with use of vacuum system in kitchen sinks were compared. In all cases, food waste was used for anaerobic digestion with energy and nutrient recovery in all cases. Compared systems all resulted in net avoidance of assessed environmental impact categories; eutrophication potential (-0.1 to -2.4 kg NO{sub 3}{sup -}eq/ton food waste), acidification potential (-0.4 to -1.0 kg SO{sub 2}{sup -}eq/ton food waste), global warming potential (-790 to -960 kg CO{sub 2}{sup -}eq/ton food waste) and primary energy use (-1.7 to -3.6 GJ/ton food waste). Collection with vacuum system results in the largest net avoidance of primary energy use, while disposal of food waste in paper bags for decentralized drying before collection result in a larger net avoidance of global warming, eutrophication and acidification. However, both these systems not have been taken into use in large scale systems yet and further investigations are needed in order to confirm the outcomes from the comparison. Ranking of scenarios differ largely if considering only emissions in the foreground system, indicating the importance of taking also downstream emissions into consideration when comparing different collection systems. The hot spot identification shows that losses of organic matter in mechanical pretreatment as well as tank connected food waste disposal systems and energy in drying and vacuum systems reply to the largest impact on the results in each system respectively.

  20. NUCLEOSYNTHETIC TUNGSTEN ISOTOPE ANOMALIES IN ACID LEACHATES OF THE MURCHISON CHONDRITE: IMPLICATIONS FOR HAFNIUM-TUNGSTEN CHRONOMETRY

    SciTech Connect (OSTI)

    Burkhardt, Christoph; Wieler, Rainer; Kleine, Thorsten; Dauphas, Nicolas

    2012-07-01

    Progressive dissolution of the Murchison carbonaceous chondrite with acids of increasing strengths reveals large internal W isotope variations that reflect a heterogeneous distribution of s- and r-process W isotopes among the components of primitive chondrites. At least two distinct carriers of nucleosynthetic W isotope anomalies must be present, which were produced in different nucleosynthetic environments. The co-variation of {sup 182}W/{sup 184}W and {sup 183}W/{sup 184}W in the leachates follows a linear trend that is consistent with a mixing line between terrestrial W and a presumed s-process-enriched component. The composition of the s-enriched component agrees reasonably well with that predicted by the stellar model of s-process nucleosynthesis. The co-variation of {sup 182}W/{sup 184}W and {sup 183}W/{sup 184}W in the leachates provides a means for correcting the measured {sup 182}W/{sup 184}W and {sup 182}W/{sup 183}W of Ca-Al-rich inclusions (CAI) for nucleosynthetic anomalies using the isotopic variations in {sup 183}W/{sup 184}W. This new correction procedure is different from that used previously, and results in a downward shift of the initial {epsilon}{sup 182}W of CAI to -3.51 {+-} 0.10 (where {epsilon}{sup 182}W is the variation in 0.01% of the {sup 182}W/{sup 183}W ratio relative to Earth's mantle). This revision leads to Hf-W model ages of core formation in iron meteorite parent bodies that are {approx}2 Myr younger than previously calculated. The revised Hf-W model ages are consistent with CAI being the oldest solids formed in the solar system, and indicate that core formation in some planetesimals occurred within {approx}2 Myr of the beginning of the solar system.

  1. System and method for simultaneously collecting serial number information from numerous identity tags

    DOE Patents [OSTI]

    Doty, Michael A. (Manteca, CA)

    1997-01-01

    A system and method for simultaneously collecting serial number information reports from numerous colliding coded-radio-frequency identity tags. Each tag has a unique multi-digit serial number that is stored in non-volatile RAM. A reader transmits an ASCII coded "D" character on a carrier of about 900 MHz and a power illumination field having a frequency of about 1.6 Ghz. A one MHz tone is modulated on the 1.6 Ghz carrier as a timing clock for a microprocessor in each of the identity tags. Over a thousand such tags may be in the vicinity and each is powered-up and clocked by the 1.6 Ghz power illumination field. Each identity tag looks for the "D" interrogator modulated on the 900 MHz carrier, and each uses a digit of its serial number to time a response. Clear responses received by the reader are repeated for verification. If no verification or a wrong number is received by any identity tag, it uses a second digital together with the first to time out a more extended period for response. Ultimately, the entire serial number will be used in the worst case collision environments; and since the serial numbers are defined as being unique, the final possibility will be successful because a clear time-slot channel will be available.

  2. System and method for simultaneously collecting serial number information from numerous identity tags

    DOE Patents [OSTI]

    Doty, M.A.

    1997-01-07

    A system and method are disclosed for simultaneously collecting serial number information reports from numerous colliding coded-radio-frequency identity tags. Each tag has a unique multi-digit serial number that is stored in non-volatile RAM. A reader transmits an ASCII coded ``D`` character on a carrier of about 900 MHz and a power illumination field having a frequency of about 1.6 Ghz. A one MHz tone is modulated on the 1.6 Ghz carrier as a timing clock for a microprocessor in each of the identity tags. Over a thousand such tags may be in the vicinity and each is powered-up and clocked by the 1.6 Ghz power illumination field. Each identity tag looks for the ``D`` interrogator modulated on the 900 MHz carrier, and each uses a digit of its serial number to time a response. Clear responses received by the reader are repeated for verification. If no verification or a wrong number is received by any identity tag, it uses a second digital together with the first to time out a more extended period for response. Ultimately, the entire serial number will be used in the worst case collision environments; and since the serial numbers are defined as being unique, the final possibility will be successful because a clear time-slot channel will be available. 5 figs.

  3. A study of tritium in municipal solid waste leachate and gas

    SciTech Connect (OSTI)

    Mutch Jr, R. D.; Mahony, J. D.

    2008-07-15

    It has become increasingly clear in the last few years that the vast majority of municipal solid waste landfills produce leachate that contains elevated levels of tritium. The authors recently conducted a study of landfills in New York and New Jersey and found that the mean concentration of tritium in the leachate from ten municipal solid waste (MSW) landfills was 33,800 pCi/L with a peak value of 192,000 pCi/L. A 2003 study in California reported a mean tritium concentration of 99,000 pCi/L with a peak value of 304,000 pCi/L. Studies in Pennsylvania and the UK produced similar results. The USEPA MCL for tritium is 20,000 pCi/L. Tritium is also manifesting itself as landfill gas and landfill gas condensate. Landfill gas condensate samples from landfills in the UK and California were found to have tritium concentrations as high as 54,400 and 513,000 pCi/L, respectively. The tritium found in MSW leachate is believed to derive principally from gaseous tritium lighting devices used in some emergency exit signs, compasses, watches, and even novelty items, such as 'glow stick' key chains. This study reports the findings of recent surveys of leachate from a number of municipal solid waste landfills, both open and closed, from throughout the United States and Europe. The study evaluates the human health and ecological risks posed by elevated tritium levels in municipal solid waste leachate and landfill gas and the implications to their safe management. We also assess the potential risks posed to solid waste management facility workers exposed to tritium-containing waste materials in transfer stations and other solid waste management facilities. (authors)

  4. DEVELOPMENT OF A TAMPER RESISTANT/INDICATING AEROSOL COLLECTION SYSTEM FOR ENVIRONMENTAL SAMPLING AT BULK HANDLING FACILITIES

    SciTech Connect (OSTI)

    Sexton, L.

    2012-06-06

    Environmental sampling has become a key component of International Atomic Energy Agency (IAEA) safeguards approaches since its approval for use in 1996. Environmental sampling supports the IAEA's mission of drawing conclusions concerning the absence of undeclared nuclear material or nuclear activities in a Nation State. Swipe sampling is the most commonly used method for the collection of environmental samples from bulk handling facilities. However, augmenting swipe samples with an air monitoring system, which could continuously draw samples from the environment of bulk handling facilities, could improve the possibility of the detection of undeclared activities. Continuous sampling offers the opportunity to collect airborne materials before they settle onto surfaces which can be decontaminated, taken into existing duct work, filtered by plant ventilation, or escape via alternate pathways (i.e. drains, doors). Researchers at the Savannah River National Laboratory and Oak Ridge National Laboratory have been working to further develop an aerosol collection technology that could be installed at IAEA safeguarded bulk handling facilities. The addition of this technology may reduce the number of IAEA inspector visits required to effectively collect samples. The principal sample collection device is a patented Aerosol Contaminant Extractor (ACE) which utilizes electrostatic precipitation principles to deposit particulates onto selected substrates. Recent work has focused on comparing traditional swipe sampling to samples collected via an ACE system, and incorporating tamper resistant and tamper indicating (TRI) technologies into the ACE system. Development of a TRI-ACE system would allow collection of samples at uranium/plutonium bulk handling facilities in a manner that ensures sample integrity and could be an important addition to the international nuclear safeguards inspector's toolkit. This work was supported by the Next Generation Safeguards Initiative (NGSI), Office of Nonproliferation and International Security (NIS), National Nuclear Security Administration (NNSA).

  5. User's guide to closure evaluation system: CES beta-test version 1. 0

    SciTech Connect (OSTI)

    Adams, T.; McCready, J.

    1992-12-01

    The Closure Evaluation System (CES) is a decision support tool, developed by the U.S. EPA's Risk Reduction Engineering Laboratory, to assist reviewers and preparers of Resource Conservation and Recovery Act (RCRA) Part B permit applications. CES is designed to serve as a checklist for identifying potential design problems in the vegetative cover, final cover, and leachate collection components of RCRA landfill closures as set forth in 40 CFR 264 and 40 CFR 265. It is not intended to be a complete automation of the evaluation process. The conclusions reached by the CES system (and it's modules) should serve either as a starting point for a more thorough investigation or as a final check applied after completion of a technical review. The CES system will, nevertheless, be useful in the directing the appropriate users attention to critical closure design issues and in applying design criteria that are supported by RCRA guidance. The CES system incorporates three modules that can assist in the evaluation of a proposed RCRA closure design: The Vegetative Cover Evaluation System (V-CES); The Final Cover Evaluation System (F-CES); and The Leachate Collection Evaluation System (L-CES). Since each module is a stand alone system, you can work with one module during a CES consultation or work with all three modules in any order.

  6. An Evaluation of Long-Term Performance of Liner Systems for Low-Level Waste Disposal Facilities

    SciTech Connect (OSTI)

    Arthur S. Rood; Annette L. Schafer; A. Jeffrey Sondrup

    2011-03-01

    Traditional liner systems consisting of a geosynthetic membrane underlying a waste disposal facility coupled with a leachate collection system have been proposed as a means of containing releases of low-level radioactive waste within the confines of the disposal facility and thereby eliminating migration of radionuclides into the vadose zone and groundwater. However, this type of hydraulic containment liner system is only effective as long as the leachate collection system remains functional or an overlying cover limits the total infiltration to the volumetric pore space of the disposal system. If either the leachate collection system fails, or the overlying cover becomes less effective during the 1,000s of years of facility lifetime, the liner may fill with water and release contaminated water in a preferential or focused manner. If the height of the liner extends above the waste, the waste will become submerged which could increase the release rate and concentration of the leachate. If the liner extends near land surface, there is the potential for contamination reaching land surface creating a direct exposure pathway. Alternative protective liner systems can be engineered that eliminate radionuclide releases to the vadose zone during operations and minimizing long term migration of radionuclides from the disposal facility into the vadose zone and aquifer. Non-traditional systems include waste containerization in steel or composite materials. This type of system would promote drainage of clean infiltrating water through the facility without contacting the waste. Other alternatives include geochemical barriers designed to transmit water while adsorbing radionuclides beneath the facility. Facility performance for a hypothetical disposal facility has been compared for the hydraulic and steel containerization liner alternatives. Results were compared in terms of meeting the DOE Order 435.1 low-level waste performance objective of 25 mrem/yr all-pathways dose during the 1) institutional control period (0-100 years), compliance period (0-1000 years) and post-compliance period (>1000 years). Evaluation of the all pathway dose included the dose from ingestion and irrigation of contaminated groundwater extracted from a well 100 meters downgradient, in addition to the dose received from direct contact of radionuclides deposited near the surface resulting from facility overflow. Depending on the disposal facility radionuclide inventory, facility design, cover performance, and the location and environment where the facility is situated, the dose from exposure via direct contact of near surface deposited radionuclides can be much greater than the dose received via transport to the groundwater and subsequent ingestion.

  7. Demonstration of the BioBaler harvesting system for collection of small-diameter woody biomass

    SciTech Connect (OSTI)

    Langholtz, Matthew H; Caffrey, Kevin R; Barnett, Elliott J; Webb, Erin; Brummette, Mark W; Downing, Mark

    2011-12-01

    As part of a project to investigate sustainable forest management practices for producing wood chips on the Oak Ridge Reservation (ORR) for the ORNL steam plant, the BioBaler was tested in various Oak Ridge locations in August of 2011. The purpose of these tests and the subsequent economic analysis was to determine the potential of this novel woody biomass harvesting method for collection of small-diameter, low value woody biomass. Results suggest that opportunities may exist for economical harvest of low-value and liability or negative-cost biomass. (e.g., invasives). This could provide the ORR and area land managers with a tool to produce feedstock while improving forest health, controlling problem vegetation, and generating local employment.

  8. In the OSTI Collections: Earth System Models | OSTI, US Dept of Energy,

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Office of Scientific and Technical Information Earth System Models Dr. Watson computer sleuthing scientist. Article Acknowledgement: Dr. William N. Watson, Physicist DOE Office of Scientific and Technical Information Experiment, theoretical analysis, and something like both Perfecting and using earth system models Enabling technologies, user training Towards decisions References Reports available from SciTech Connect Research organizations Additional References "The abstract of the

  9. Web-GIS oriented systems viability for municipal solid waste selective collection optimization in developed and transient economies

    SciTech Connect (OSTI)

    Rada, E.C.; Ragazzi, M.; Fedrizzi, P.

    2013-04-15

    Highlights: ? As an appropriate solution for MSW management in developed and transient countries. ? As an option to increase the efficiency of MSW selective collection. ? As an opportunity to integrate MSW management needs and services inventories. ? As a tool to develop Urban Mining actions. - Abstract: Municipal solid waste management is a multidisciplinary activity that includes generation, source separation, storage, collection, transfer and transport, processing and recovery, and, last but not least, disposal. The optimization of waste collection, through source separation, is compulsory where a landfill based management must be overcome. In this paper, a few aspects related to the implementation of a Web-GIS based system are analyzed. This approach is critically analyzed referring to the experience of two Italian case studies and two additional extra-European case studies. The first case is one of the best examples of selective collection optimization in Italy. The obtained efficiency is very high: 80% of waste is source separated for recycling purposes. In the second reference case, the local administration is going to be faced with the optimization of waste collection through Web-GIS oriented technologies for the first time. The starting scenario is far from an optimized management of municipal solid waste. The last two case studies concern pilot experiences in China and Malaysia. Each step of the Web-GIS oriented strategy is comparatively discussed referring to typical scenarios of developed and transient economies. The main result is that transient economies are ready to move toward Web oriented tools for MSW management, but this opportunity is not yet well exploited in the sector.

  10. Numerical Studies of Collective Phenomena in Two-Dimensional Electron and Cold Atom Systems

    SciTech Connect (OSTI)

    Rezayi, Edward

    2013-07-25

    Numerical calculations were carried out to investigate a number of outstanding questions in both two-dimensional electron and cold atom systems. These projects aimed to increase our understanding of the properties of and prospects for non-Abelian states in quantum Hall matter.

  11. Fact Sheet: Best Practices Handbook for the Collection and Use of Solar Energy Applications; Best Practices Handbook for the Collection and Use of Solar Energy Applications (Fact Sheet), Energy Systems Integration (ESI), NREL (National Renewable Energy Laboratory)

    SciTech Connect (OSTI)

    2015-06-01

    This fact sheet presents highlights from the Best Practices Handbook for the Collection and Use of Solar Resource Data for Solar Energy Applications, which provides detailed information about solar resource data and the resulting data products needed for planning each stage of large concentrating solar power systems, from initial site selection to system operations.

  12. A comprehensive collection of systems biology data characterizing the host response to viral infection

    SciTech Connect (OSTI)

    Aevermann, Brian D.; Pickett, Brett E.; Kumar, Sanjeev; Klem, Edward B.; Agnihothram, Sudhakar; Askovich, Peter S.; Bankhead, Armand; Bolles, Meagan; Carter, Victoria; Chang, Jean H.; Clauss, Therese R. W.; Dash, Pradyot; Diercks, Alan H.; Eisfeld, Amie J.; Ellis, Amy L.; Fan, Shufang; Ferris, Martin T.; Gralinski, Lisa; Green, Richard; Gritsenko, Marina A.; Hatta, Masato; Heegel, Robert A.; Jacobs, Jon M.; Jeng, Sophia; Josset, Laurence; Kaiser, Shari M.; Kelly, Sarah; Law, Gale Lynn; Li, Chengjun; Li, Jiangning; Long, Casey; Luna, Maria L.; Matzke, Melissa M.; McDermott, Jason E.; Menachery, Vineet; Metz, Thomas O.; Mitchell, Hugh D.; Monroe, Matthew E.; Navarro, Garnet; Neumann, Gabriele; Podyminogin, Rebecca L.; Purvine, Samuel O.; Rosenberger, Carrie; Sanders, Catherine J.; Schepmoes, Athena A.; Shukla, Anil K.; Sims, Amy; Sova, Pavel; Tam, Vincent C.; Tchitchek, Nicholas; Thomas, Paul G.; Tilton, Susan C.; Totura, Allison L.; Wang, Jing; Webb-Robertson, Bobbie-Jo M.; Wen, Ji; Weiss, Jeffrey M.; Yang, Feng; Yount, Boyd; Zhang, Qibin; Mcweeney, Shannon K.; Smith, Richard D.; Waters, Katrina M.; Kawaoka, Yoshihiro; Baric, Ralph; Aderem, Alan; Katze, Michael G.; Scheuermann, Richard H.

    2014-10-14

    The Systems Biology for Infectious Diseases Research program was established by the U.S. National Institute of Allergy and Infectious Diseases to investigate host-pathogen interactions at a systems level. This program generated 47 transcriptomic and proteomic datasets from 30 studies that investigate in vivo and in vitro host responses to viral infections. Human pathogens in the Orthomyxoviridae and Coronaviridae families, especially pandemic H1N1 and avian H5N1 influenza A viruses and severe acute respiratory syndrome coronavirus (SARS-CoV), were investigated. Study validation was demonstrated via experimental quality control measures and meta-analysis of independent experiments performed under similar conditions. Primary assay results are archived at the GEO and PeptideAtlas public repositories, while processed statistical results together with standardized metadata are publically available at the Influenza Research Database (www.fludb.org) and the Virus Pathogen Resource (www.viprbrc.org). As a result, by comparing data from mutant versus wild-type virus and host strains, RNA versus protein differential expression, and infection with genetically similar strains, these data can be used to further investigate genetic and physiological determinants of host responses to viral infection.

  13. A comprehensive collection of systems biology data characterizing the host response to viral infection

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Aevermann, Brian D.; Pickett, Brett E.; Kumar, Sanjeev; Klem, Edward B.; Agnihothram, Sudhakar; Askovich, Peter S.; Bankhead, Armand; Bolles, Meagan; Carter, Victoria; Chang, Jean H.; et al

    2014-10-14

    The Systems Biology for Infectious Diseases Research program was established by the U.S. National Institute of Allergy and Infectious Diseases to investigate host-pathogen interactions at a systems level. This program generated 47 transcriptomic and proteomic datasets from 30 studies that investigate in vivo and in vitro host responses to viral infections. Human pathogens in the Orthomyxoviridae and Coronaviridae families, especially pandemic H1N1 and avian H5N1 influenza A viruses and severe acute respiratory syndrome coronavirus (SARS-CoV), were investigated. Study validation was demonstrated via experimental quality control measures and meta-analysis of independent experiments performed under similar conditions. Primary assay results are archivedmore » at the GEO and PeptideAtlas public repositories, while processed statistical results together with standardized metadata are publically available at the Influenza Research Database (www.fludb.org) and the Virus Pathogen Resource (www.viprbrc.org). As a result, by comparing data from mutant versus wild-type virus and host strains, RNA versus protein differential expression, and infection with genetically similar strains, these data can be used to further investigate genetic and physiological determinants of host responses to viral infection.« less

  14. Parallel log structured file system collective buffering to achieve a compact representation of scientific and/or dimensional data

    DOE Patents [OSTI]

    Grider, Gary A.; Poole, Stephen W.

    2015-09-01

    Collective buffering and data pattern solutions are provided for storage, retrieval, and/or analysis of data in a collective parallel processing environment. For example, a method can be provided for data storage in a collective parallel processing environment. The method comprises receiving data to be written for a plurality of collective processes within a collective parallel processing environment, extracting a data pattern for the data to be written for the plurality of collective processes, generating a representation describing the data pattern, and saving the data and the representation.

  15. Enhancement of the anaerobic hydrolysis and fermentation of municipal solid waste in leachbed reactors by varying flow direction during water addition and leachate recycle

    SciTech Connect (OSTI)

    Uke, Matthew N.; Stentiford, Edward

    2013-06-15

    Highlights: ? Combined downflow and upflow water addition improved hydraulic conductivity. ? Upflow water addition unclogged perforated screen leading to more leachate flow. ? The volume of water added and transmitted positively correlated with hydrolysis process. ? Combined downflow and upflow water addition increased COD production and yield. ? Combined downflow and upflow leachate recycle improved leachate and COD production. - Abstract: Poor performance of leachbed reactors (LBRs) is attributed to channelling, compaction from waste loading, unidirectional water addition and leachate flow causing reduced hydraulic conductivity and leachate flow blockage. Performance enhancement was evaluated in three LBRs M, D and U at 22 3 C using three water addition and leachate recycle strategies; water addition was downflow in D throughout, intermittently upflow and downflow in M and U with 77% volume downflow in M, 54% volume downflow in U while the rest were upflow. Leachate recycle was downflow in D, alternately downflow and upflow in M and upflow in U. The strategy adopted in U led to more water addition (30.3%), leachate production (33%) and chemical oxygen demand (COD) solubilisation (33%; 1609 g against 1210 g) compared to D (control). The total and volatile solids (TS and VS) reductions were similar but the highest COD yield (g-COD/g-TS and g-COD/g-VS removed) was in U (1.6 and 1.9); the values were 1.33 and 1.57 for M, and 1.18 and 1.41 for D respectively. The strategy adopted in U showed superior performance with more COD and leachate production compared to reactors M and D.

  16. On-Site Pilot Study - Removal of Uranium, Radium-226 and Arsenic from Impacted Leachate by Reverse Osmosis - 13155

    SciTech Connect (OSTI)

    McMurray, Allan; Everest, Chris; Rilling, Ken; Vandergaast, Gary; LaMonica, David

    2013-07-01

    Conestoga-Rovers and Associates (CRA-LTD) performed an on-site pilot study at the Welcome Waste Management Facility in Port Hope, Ontario, Canada, to evaluate the effectiveness of a unique leachate treatment process for the removal of radioactive contaminants from leachate impacted by low-level radioactive waste. Results from the study also provided the parameters needed for the design of the CRA-LTD full scale leachate treatment process design. The final effluent water quality discharged from the process to meet the local surface water discharge criteria. A statistical software package was utilized to obtain the analysis of variance (ANOVA) for the results from design of experiment applied to determine the effect of the evaluated factors on the measured responses. The factors considered in the study were: percent of reverse osmosis permeate water recovery, influent coagulant dosage, and influent total dissolved solids (TDS) dosage. The measured responses evaluated were: operating time, average specific flux, and rejection of radioactive contaminants along with other elements. The ANOVA for the design of experiment results revealed that the operating time is affected by the percent water recovery to be achieved and the flocculant dosage over the range studied. The average specific flux and rejection for the radioactive contaminants were not affected by the factors evaluated over the range studied. The 3 month long on-site pilot testing on the impacted leachate revealed that the CRA-LTD leachate treatment process was robust and produced an effluent water quality that met the surface water discharge criteria mandated by the Canadian Nuclear Safety Commission and the local municipality. (authors)

  17. MOBILIZATION AND CHARACTERIZATION OF COLLOIDS GENERATED FROM CEMENT LEACHATES MOVING THROUGH A SRS SANDY SEDIMENT

    SciTech Connect (OSTI)

    Li, D.; Roberts, K.; Kaplan, D.; Seaman, J.

    2011-09-20

    Naturally occurring mobile colloids are ubiquitous and are involved in many important processes in the subsurface zone. For example, colloid generation and subsequent mobilization represent a possible mechanism for the transport of contaminants including radionuclides in the subsurface environments. For colloid-facilitated transport to be significant, three criteria must be met: (1) colloids must be generated; (2) contaminants must associate with the colloids preferentially to the immobile solid phase (aquifer); and (3) colloids must be transported through the groundwater or in subsurface environments - once these colloids start moving they become 'mobile colloids'. Although some experimental investigations of particle release in natural porous media have been conducted, the detailed mechanisms of release and re-deposition of colloidal particles within natural porous media are poorly understood. Even though this vector of transport is known, the extent of its importance is not known yet. Colloid-facilitated transport of trace radionuclides has been observed in the field, thus demonstrating a possible radiological risk associated with the colloids. The objective of this study was to determine if cementitious leachate would promote the in situ mobilization of natural colloidal particles from a SRS sandy sediment. The intent was to determine whether cementitious surface or subsurface structure would create plumes that could produce conditions conducive to sediment dispersion and mobile colloid generation. Column studies were conducted and the cation chemistries of influents and effluents were analyzed by ICP-OES, while the mobilized colloids were characterized using XRD, SEM, EDX, PSD and Zeta potential. The mobilization mechanisms of colloids in a SRS sandy sediment by cement leachates were studied.

  18. Modeling of leachate generation from MSW landfills by a 2-dimensional 2-domain approach

    SciTech Connect (OSTI)

    Fellner, Johann

    2010-11-15

    The flow of water through Municipal Solid Waste (MSW) landfills is highly non-uniform and dominated by preferential pathways. Thus, concepts to simulate landfill behavior require that a heterogeneous flow regime is considered. Recent models are based on a 2-domain approach, differentiating between channel domain with high hydraulic conductivity, and matrix domain of slow water movement with high water retention capacity. These models focus on the mathematical description of rapid water flow in channel domain. The present paper highlights the importance of water exchange between the two domains, and expands the 1-dimensional, 2-domain flow model by taking into account water flows in two dimensions. A flow field consisting of a vertical path (channel domain) surrounded by the waste mass (matrix domain) is defined using the software HYDRUS-2D. When the new model is calibrated using data sets from a MSW-landfill site the predicted leachate generation corresponds well with the observed leachate discharge. An overall model efficiency in terms of r{sup 2} of 0.76 was determined for a simulation period of almost 4 years. The results confirm that water in landfills follows a preferential path way characterized by high permeability (K{sub s} = 300 m/d) and zero retention capacity, while the bulk of the landfill (matrix domain) is characterized by low permeability (K{sub s} = 0.1 m/d) and high retention capacity. The most sensitive parameters of the model are the hydraulic conductivities of the channel domain and the matrix domain, and the anisotropy of the matrix domain.

  19. Tightly integrated single- and multi-crystal data collection strategy calculation and parallelized data processing in JBluIce beamline control system

    SciTech Connect (OSTI)

    Pothineni, Sudhir Babu; Venugopalan, Nagarajan; Ogata, Craig M.; Hilgart, Mark C.; Stepanov, Sergey; Sanishvili, Ruslan; Becker, Michael; Winter, Graeme; Sauter, Nicholas K.; Smith, Janet L.; Fischetti, Robert F.

    2014-11-18

    The calculation of single- and multi-crystal data collection strategies and a data processing pipeline have been tightly integrated into the macromolecular crystallographic data acquisition and beamline control software JBluIce. Both tasks employ wrapper scripts around existing crystallographic software. JBluIce executes scripts through a distributed resource management system to make efficient use of all available computing resources through parallel processing. The JBluIce single-crystal data collection strategy feature uses a choice of strategy programs to help users rank sample crystals and collect data. The strategy results can be conveniently exported to a data collection run. The JBluIce multi-crystal strategy feature calculates a collection strategy to optimize coverage of reciprocal space in cases where incomplete data are available from previous samples. The JBluIce data processing runs simultaneously with data collection using a choice of data reduction wrappers for integration and scaling of newly collected data, with an option for merging with pre-existing data. Data are processed separately if collected from multiple sites on a crystal or from multiple crystals, then scaled and merged. Results from all strategy and processing calculations are displayed in relevant tabs of JBluIce.

  20. Tightly integrated single- and multi-crystal data collection strategy calculation and parallelized data processing in JBluIce beamline control system

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Pothineni, Sudhir Babu; Venugopalan, Nagarajan; Ogata, Craig M.; Hilgart, Mark C.; Stepanov, Sergey; Sanishvili, Ruslan; Becker, Michael; Winter, Graeme; Sauter, Nicholas K.; Smith, Janet L.; et al

    2014-11-18

    The calculation of single- and multi-crystal data collection strategies and a data processing pipeline have been tightly integrated into the macromolecular crystallographic data acquisition and beamline control software JBluIce. Both tasks employ wrapper scripts around existing crystallographic software. JBluIce executes scripts through a distributed resource management system to make efficient use of all available computing resources through parallel processing. The JBluIce single-crystal data collection strategy feature uses a choice of strategy programs to help users rank sample crystals and collect data. The strategy results can be conveniently exported to a data collection run. The JBluIce multi-crystal strategy feature calculates amore » collection strategy to optimize coverage of reciprocal space in cases where incomplete data are available from previous samples. The JBluIce data processing runs simultaneously with data collection using a choice of data reduction wrappers for integration and scaling of newly collected data, with an option for merging with pre-existing data. Data are processed separately if collected from multiple sites on a crystal or from multiple crystals, then scaled and merged. Results from all strategy and processing calculations are displayed in relevant tabs of JBluIce.« less

  1. Collecting apparatus

    DOE Patents [OSTI]

    Duncan, Charles P.

    1983-01-01

    An improved collecting apparatus for small aquatic or airborne organisms such as plankton, larval fish, insects, etc. The improvement constitutes an apertured removal container within which is retained a collecting bag, and which is secured at the apex of a conical collecting net. Such collectors are towed behind a vessel or vehicle with the open end of the conical net facing forward for trapping the aquatic or airborne organisms within the collecting bag, while allowing the water or air to pass through the apertures in the container. The container is readily removable from the collecting net whereby the collecting bag can be quickly removed and replaced for further sample collection. The collecting bag is provided with means for preventing the bag from being pulled into the container by the water or air flowing therethrough.

  2. Anaerobic treatment of sludge from a nitrification-denitrification landfill leachate plant

    SciTech Connect (OSTI)

    Maranon, E. . E-mail: emara@uniovi.es; Castrillon, L.; Fernandez, Y.; Fernandez, E.

    2006-07-01

    The viability of anaerobic digestion of sludge from a MSW landfill leachate treatment plant, with COD values ranging between 15,000 and 19,400 mg O{sub 2} dm{sup -3}, in an upflow anaerobic sludge blanket reactor was studied. The reactor employed had a useful capacity of 9 l, operating at mesophilic temperature. Start-up of the reactor was carried out in different steps, beginning with diluted sludge and progressively increasing the amount of sludge fed into the reactor. The study was carried out over a period of 7 months. Different amounts of methanol were added to the feed, ranging between 6.75 and 1 cm{sup 3} dm{sup -3} of feed in order to favour the growth of methanogenic flora. The achieved biodegradation of the sludge using an upflow anaerobic sludge blanket Reactor was very high for an HRT of 9 days, obtaining decreases in COD of 84-87% by the end of the process. Purging of the digested sludge represented {approx}16% of the volume of the treated sludge.

  3. Cybersnooping: Collection

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Cybersnooping: Collection and Analysis of Metadata and Content Professor Edward Felten Princeton University Wednesday, Nov 20, 2013 - 4:15PM MBG AUDITORIUM Refreshments at 4:00PM The PrinceTon Plasma Physics laboraTory is a U.s. DeParTmenT of energy faciliTy Recent reports indicate that governments (and perhaps others) have been collecting large amount of metadata and possibly content of phone calls, emails, and other communications. This talk will re- view what we know about current collection

  4. Anaerobic digestion of pressed off leachate from the organic fraction of municipal solid waste

    SciTech Connect (OSTI)

    Nayono, Satoto E.; Winter, Josef; Gallert, Claudia

    2010-10-15

    A highly polluted liquid ('press water') was obtained from the pressing facility for the organic fraction of municipal solid waste in a composting plant. Methane productivity of the squeezed-off leachate was investigated in batch assays. To assess the technical feasibility of 'press water' as a substrate for anaerobic digestion, a laboratory-scale glass column reactor was operated semi-continuously at 37 {sup o}C. A high methane productivity of 270 m{sup -3} CH{sub 4} ton{sup -1} COD{sub added} or 490 m{sup -3} CH{sub 4} ton{sup -1} VS{sub added} was achieved in the batch experiment. The semi-continuously run laboratory-scale reactor was initially operated at an organic loading rate of 10.7 kg COD m{sup -3} d{sup -1}. The loading was increased to finally 27.7 kg COD m{sup -3} d{sup -1}, corresponding to a reduction of the hydraulic retention time from initially 20 to finally 7.7 days. During the digestion, a stable elimination of organic material (measured as COD elimination) of approximately 60% was achieved. Linearly with the increment of the OLR, the volumetric methane production of the reactor increased from 2.6 m{sup 3} m{sub reactor}{sup -3} d{sup -1} to 7.1 m{sup 3} m{sub reactor}{sup -3} d{sup -1}. The results indicated that 'press water' from the organic fraction of municipal solid waste was a suitable substrate for anaerobic digestion which gave a high biogas yield even at very high loading rates.

  5. The Solarize Guidebook: A community guide to collective purchasing of residential PV systems (Book), SunShot, U.S. Department of Energy (DOE)

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    SOLARIZE GUIDEBOOK: A community guide to collective purchasing of residential PV systems 1 ACKNOWLEDGEMENTS This guide is an updated version of the original The Solarize Guidebook, published in February 2011 (see www.nrel.gov/docs/fy11osti/50440.pdf), which was developed for the National Renewable Energy Laboratory and the City of Portland. The original Solarize campaigns were initiated and replicated by Portland's Neighborhood Coalition network with help from the Energy Trust of Oregon, City of

  6. Collective instabilities

    SciTech Connect (OSTI)

    K.Y. Ng

    2003-08-25

    The lecture covers mainly Sections 2.VIII and 3.VII of the book ''Accelerator Physics'' by S.Y. Lee, plus mode-coupling instabilities and chromaticity-driven head-tail instability. Besides giving more detailed derivation of many equations, simple interpretations of many collective instabilities are included with the intention that the phenomena can be understood more easily without going into too much mathematics. The notations of Lee's book as well as the e{sup jwt} convention are followed.

  7. The AmeriFlux Data Activity and Data System: An Evolving Collection of Data Management Techniques, Tools, Products and Services

    SciTech Connect (OSTI)

    Boden, Thomas A; Krassovski, Misha B; Yang, Bai

    2013-01-01

    The Carbon Dioxide Information Analysis Center (CDIAC) at Oak Ridge National Laboratory (ORNL), USA has provided scientific data management support for the U.S. Department of Energy and international climate change science since 1982. Over this period, climate change science has expanded from research focusing on basic understanding of geochemical cycles, particularly the carbon cycle, to integrated research addressing climate change impacts, vulnerability, adaptation, and mitigation. Interests in climate change data and information worldwide have grown remarkably and, as a result, so have demands and expectations for CDIAC s data systems. To meet the growing demands, CDIAC s strategy has been to design flexible data systems using proven technologies blended with new, evolving technologies and standards. CDIAC development teams are multidisciplinary and include computer science and information technology expertise, but also scientific expertise necessary to address data quality and documentation issues and to identify data products and system capabilities needed by climate change scientists. CDIAC has learned there is rarely a single commercial tool or product readily available to satisfy long-term scientific data system requirements (i.e., one size does not fit all and the breadth and diversity of environmental data are often too complex for easy use with commercial products) and typically deploys a variety of tools and data products in an effort to provide credible data freely to users worldwide. Like many scientific data management applications, CDIAC s data systems are highly customized to satisfy specific scientific usage requirements (e.g., developing data products specific for model use) but are also designed to be flexible and interoperable to take advantage of new software engineering techniques, standards (e.g., metadata standards) and tools and to support future Earth system data efforts (e.g., ocean acidification). CDIAC has provided data management support for numerous long-term measurement projects crucial to climate change science. One current example is the AmeriFlux measurement network. AmeriFlux provides continuous measurements from forests, grasslands, wetlands, and croplands in North, Central, and South America and offers important insight about carbon cycling in terrestrial ecosystems. We share our approaches in satisfying the challenges of delivering AmeriFlux data worldwide to benefit others with similar challenges handling climate change data, further heighten awareness and use of an outstanding ecological data resource, and highlight expanded software engineering applications being used for climate change measurement data.

  8. Solar collection

    SciTech Connect (OSTI)

    Cole, S.L.

    1984-08-01

    This report contains summaries and pictures of projects funded by the Appropriate Technology Small Grants Program which include the following solar technologies: solar dish; photovoltaics; passive solar building and solar hot water system; Trombe wall; hot air panel; hybrid solar heating system; solar grain dryer; solar greenhouse; solar hot water workshops; and solar workshops.

  9. New and Improved Data Logging and Collection System for Atmospheric Radiation Measurement Climate Research Facility, Tropical Western Pacific, and North Slope of Alaska Sky Radiation, Ground Radiation, and MET Systems

    SciTech Connect (OSTI)

    Ritsche, M.T.; Holdridge, D.J.; Pearson, R.

    2005-03-18

    Aging systems and technological advances mandated changes to the data collection systems at the Atmospheric Radiation Measurement (ARM) Program's Tropical Western Pacific (TWP) and North Slope of Alaska (NSA) ARM Climate Research Facility (ACRF) sites. Key reasons for the upgrade include the following: achieve consistency across all ACRF sites for easy data use and operational maintenance; minimize the need for a single mentor requiring specialized knowledge and training; provide local access to real-time data for operational support, intensive operational period (IOP) support, and public relations; eliminate problems with physical packaging (condensation, connectors, etc.); and increase flexibility in programming and control of the data logger.

  10. Best Practices Handbook for the Collection and Use of Solar Energy Applications (Fact Sheet), Energy Systems Integration (ESI), NREL (National Renewable Energy Laboratory)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Best Practices Handbook for the Collection and Use of Solar Resource Data for Solar Energy Applications Comprehensive handbook helps the solar industry collect and interpret solar resource data for each stage of a solar energy project. About the Handbook The Best Practices Handbook for the Collection and Use of Solar Radiation Data for Solar Energy Applications provides the solar energy industry with a single document addressing key aspects of solar resource characterization needed for planning

  11. Advanced Containment System

    DOE Patents [OSTI]

    Kostelnik, Kevin M. (Idaho Falls, ID); Kawamura, Hideki (Tokyo, JP); Richardson, John G. (Idaho Falls, ID); Noda, Masaru (Tokyo, JP)

    2005-02-08

    An advanced containment system for containing buried waste and associated leachate. The advanced containment system comprises a plurality of casing sections with each casing section interlocked to an adjacent casing section. Each casing section includes a complementary interlocking structure that interlocks with the complementary interlocking structure on an adjacent casing section. A barrier filler substantially fills the casing sections and may substantially fill the spaces of the complementary interlocking structure to form a substantially impermeable barrier. Some of the casing sections may include sensors so that the casing sections and the zone of interest may be remotely monitored after the casing sections are emplaced in the ground.

  12. Data Collection and Mapping | Open Energy Information

    Open Energy Info (EERE)

    systems.2 In addition to the collection surface data, field mapping may be used to "ground truth" data collected by other methods, such as remote sensing. Water, gas, soil...

  13. MONTICELLO NPL SITES FFA QUARTERLY REPORT: October 1

    Office of Legacy Management (LM)

    October 1 - December 31,2006 DOE Project Coordinator: Art KJeinrath 1.0 MMTS Activities Repository and Pond 4 * Monthly and quarterly inspection of the repository identified no problems other than shmb damage by voles (inspection checklists attached) * Monthly inspection ofPond 4 identified no unacceptable conditions. * Pond 4 leachate detection and removal systems operated at normal levels (leachate pumping summary attached). * Repository leachate collection and removal system (LCRS) and

  14. Collective network for computer structures

    DOE Patents [OSTI]

    Blumrich, Matthias A. (Ridgefield, CT); Coteus, Paul W. (Yorktown Heights, NY); Chen, Dong (Croton On Hudson, NY); Gara, Alan (Mount Kisco, NY); Giampapa, Mark E. (Irvington, NY); Heidelberger, Philip (Cortlandt Manor, NY); Hoenicke, Dirk (Ossining, NY); Takken, Todd E. (Brewster, NY); Steinmacher-Burow, Burkhard D. (Wernau, DE); Vranas, Pavlos M. (Bedford Hills, NY)

    2011-08-16

    A system and method for enabling high-speed, low-latency global collective communications among interconnected processing nodes. The global collective network optimally enables collective reduction operations to be performed during parallel algorithm operations executing in a computer structure having a plurality of the interconnected processing nodes. Router devices ate included that interconnect the nodes of the network via links to facilitate performance of low-latency global processing operations at nodes of the virtual network and class structures. The global collective network may be configured to provide global barrier and interrupt functionality in asynchronous or synchronized manner. When implemented in a massively-parallel supercomputing structure, the global collective network is physically and logically partitionable according to needs of a processing algorithm.

  15. Collective network for computer structures

    DOE Patents [OSTI]

    Blumrich, Matthias A; Coteus, Paul W; Chen, Dong; Gara, Alan; Giampapa, Mark E; Heidelberger, Philip; Hoenicke, Dirk; Takken, Todd E; Steinmacher-Burow, Burkhard D; Vranas, Pavlos M

    2014-01-07

    A system and method for enabling high-speed, low-latency global collective communications among interconnected processing nodes. The global collective network optimally enables collective reduction operations to be performed during parallel algorithm operations executing in a computer structure having a plurality of the interconnected processing nodes. Router devices are included that interconnect the nodes of the network via links to facilitate performance of low-latency global processing operations at nodes of the virtual network. The global collective network may be configured to provide global barrier and interrupt functionality in asynchronous or synchronized manner. When implemented in a massively-parallel supercomputing structure, the global collective network is physically and logically partitionable according to the needs of a processing algorithm.

  16. Wireless technology collects real-time information from oil and...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Wireless technology collects real-time information from oil and gas wells Wireless technology collects real-time information from oil and gas wells The patented system delivers ...

  17. Draft Sample Collection Instrument

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Sample Collection Instrument Davis-Bacon Semi-annual Labor Compliance Report OMB Control Number 1910-New Please note that different DOE programs will use different collection instruments. Wherever possible, the data collection will be integrated into existing reporting processes for recipients of DOE financial assistance and prime contractors use. The sample collection instrument below would be used by recipients of Energy Efficiency Conservation Block Grants, State Energy Program grants, and

  18. Film Collection Volume One

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Volume One Film Collection Volume Two 75th Anniversary Hydropower in the Northwest Woody Guthrie Videos Strategic Direction Branding & Logos Power of the River History Book...

  19. Distributed resource management: garbage collection

    SciTech Connect (OSTI)

    Bagherzadeh, N.

    1987-01-01

    In recent years, there has been a great interest in designing high-performance distributed symbolic-processing computers. These architectures have special needs for resource management and dynamic reclamation of unused memory cells and objects. The memory management or garbage-collection aspects of these architectures are studied. Also introduced is a synchronous distributed algorithm for garbage collection. A special data structure is defined to handle the distributed nature of the problem. The author formally expresses the algorithm and shows the results of a synchronous garbage-collection simulation and its effect on the interconnection-network message to traffic. He presents an asynchronous distributed garbage collection to handle the resource management for a system that does not require a global synchronization mechanism. The distributed data structure is modified to include the asynchronous aspects of the algorithm. This method is extended to a multiple-mutator scheme, and the problem of having several processors share portion of a cyclical graph is discussed. Two models for the analytical study of the garbage-collection algorithms discussed are provided.

  20. UESC Data Collection Update

    Broader source: Energy.gov [DOE]

    Presentationgiven at the April 2012 Federal Utility Partnership Working Group (FUPWG) meetingprovides an overview of utility energy service contract (UESC) data collection, including what is needed, how to submit data, and why it is important.

  1. Vectorized garbage collection

    SciTech Connect (OSTI)

    Appel, A.W.; Bendiksen, A.

    1988-01-01

    Garbage collection can be done in vector mode on supercomputers like the Cray-2 and the Cyber 205. Both copying collection and mark-and-sweep can be expressed as breadth-first searches in which the queue can be processed in parallel. The authors have designed a copying garbage collector whose inner loop works entirely in vector mode. The only significant limitation of the algorithm is that if the size of the records is not constant, the implementation becomes much more complicated. The authors give performance measurements of the algorithm as implemented for Lisp CONS cells on the Cyber 205. Vector-mode garbage collection performs up to 9 times faster than scalar-mode collection.

  2. Portable data collection device

    DOE Patents [OSTI]

    French, Patrick D. (Aurora, CO)

    1996-01-01

    The present invention provides a portable data collection device that has a variety of sensors that are interchangeable with a variety of input ports in the device. The various sensors include a data identification feature that provides information to the device regarding the type of physical data produced by each sensor and therefore the type of sensor itself. The data identification feature enables the device to locate the input port where the sensor is connected and self adjust when a sensor is removed or replaced. The device is able to collect physical data, whether or not a function of a time.

  3. Portable data collection device

    DOE Patents [OSTI]

    French, P.D.

    1996-06-11

    The present invention provides a portable data collection device that has a variety of sensors that are interchangeable with a variety of input ports in the device. The various sensors include a data identification feature that provides information to the device regarding the type of physical data produced by each sensor and therefore the type of sensor itself. The data identification feature enables the device to locate the input port where the sensor is connected and self adjust when a sensor is removed or replaced. The device is able to collect physical data, whether or not a function of a time. 7 figs.

  4. Information Collection Management Program

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2006-10-11

    This Order sets forth DOE requirements and responsibilities for implementing the information collection management provisions of the Paperwork Reduction Act of 1995 and the Office of Management and Budgets implementing regulation Controlling Paperwork Burdens on the Public, as contained in 5 CFR 1320. No cancellation.

  5. Collective network routing

    DOE Patents [OSTI]

    Hoenicke, Dirk

    2014-12-02

    Disclosed are a unified method and apparatus to classify, route, and process injected data packets into a network so as to belong to a plurality of logical networks, each implementing a specific flow of data on top of a common physical network. The method allows to locally identify collectives of packets for local processing, such as the computation of the sum, difference, maximum, minimum, or other logical operations among the identified packet collective. Packets are injected together with a class-attribute and an opcode attribute. Network routers, employing the described method, use the packet attributes to look-up the class-specific route information from a local route table, which contains the local incoming and outgoing directions as part of the specifically implemented global data flow of the particular virtual network.

  6. Advanced Containment System

    DOE Patents [OSTI]

    Kostelnik, Kevin M. (Idaho Falls, ID); Kawamura, Hideki (Tokyo, JP); Richardson, John G. (Idaho Falls, ID); Noda, Masaru (Tokyo, JP)

    2004-10-12

    An advanced containment system for containing buried waste and associated leachate. A trench is dug on either side of the zone of interest containing the buried waste so as to accommodate a micro tunnel boring machine. A series of small diameter tunnels are serially excavated underneath the buried waste. The tunnels are excavated by the micro tunnel boring machine at a consistent depth and are substantially parallel to each other. As tunneling progresses, steel casing sections are connected end to end in the excavated portion of the tunnel so that a steel tube is formed. Each casing section has complementary interlocking structure running its length that interlocks with complementary interlocking structure on the adjacent casing section. Thus, once the first tube is emplaced, placement of subsequent tubes is facilitated by the complementary interlocking structure on the adjacent, previously placed, casing sections.

  7. Advanced Containment System

    DOE Patents [OSTI]

    Kostelnik, Kevin M. (Idaho Falls, ID); Kawamura, Hideki (Tokyo, JP); Richardson, John G. (Idaho Falls, ID); Noda, Masaru (Tokyo, JP)

    2005-05-24

    An advanced containment system for containing buried waste and associated leachate. A trench is dug on either side of the zone of interest containing the buried waste so as to accommodate a micro tunnel boring machine. A series of small diameter tunnels are serially excavated underneath the buried waste. The tunnels are excavated by the micro tunnel boring machine at a consistent depth and are substantially parallel to each other. As tunneling progresses, steel casing sections are connected end to end in the excavated portion of the tunnel so that a steel tube is formed. Each casing section has complementary interlocking structure running its length that interlocks with complementary interlocking structure on the adjacent casing section. Thus, once the first tube is emplaced, placement of subsequent tubes is facilitated by the complementary interlocking structure on the adjacent, previously placed, casing sections.

  8. Portable liquid collection electrostatic precipitator

    DOE Patents [OSTI]

    Carlson, Duane C.; DeGange, John J.; Halverson, Justin E.

    2005-10-18

    A portable liquid collection electrostatic collection precipitator for analyzing air is provided which is a relatively small, self-contained device. The device has a tubular collection electrode, a reservoir for a liquid, and a pump. The pump pumps the liquid into the collection electrode such that the liquid flows down the exterior of the collection electrode and is recirculated to the reservoir. An air intake is provided such that air to be analyzed flows through an ionization section to ionize analytes in the air, and then flows near the collection electrode where ionized analytes are collected. A portable power source is connected to the air intake and the collection electrode. Ionizable constituents in the air are ionized, attracted to the collection electrode, and precipitated in the liquid. The precipitator may also have an analyzer for the liquid and may have a transceiver allowing remote operation and data collection.

  9. Modcopter: Prompt, Precise Aerial Sample Collection Using Unmanned...

    Office of Scientific and Technical Information (OSTI)

    Title: Modcopter: Prompt, Precise Aerial Sample Collection Using Unmanned Systems Authors: Curtis, Aaron 1 ; Elliott, James 2 ; Ronquest, Michael 3 ; Mascarenas, David D. 3 ...

  10. MODCOPTER: Prompt, Precise Aerial Sample Collection Using Unmanned...

    Office of Scientific and Technical Information (OSTI)

    Title: MODCOPTER: Prompt, Precise Aerial Sample Collection Using Unmanned Systems Authors: Mascarenas, David D. 1 ; Curtis, Aaron 2 ; Elliott, James 3 ; Ronquest, Michael 1 ...

  11. Evidence for coupling between collective state and phonons in...

    Office of Scientific and Technical Information (OSTI)

    for coupling between collective state and phonons in two-dimensional charge-density-wave systems Citation Details In-Document Search Title: Evidence for coupling between...

  12. Information Collection | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Information Collection Information Collection The Office of Environment, Health, Safety and Security (EHSS) continues to seek for ways to minimize the burden of information collection on DOE and its contractors. DOE collects information concerning the health, safety and security of DOE employees including its contractors and facilities. The information collected will be used by DOE to exercise management oversight over Management and Operating (M&O) contractors of DOE's Government-Owned

  13. Aerobic landfill bioreactor

    DOE Patents [OSTI]

    Hudgins, Mark P; Bessette, Bernard J; March, John C; McComb, Scott T.

    2002-01-01

    The present invention includes a system of decomposing municipal solid waste (MSW) within a landfill by converting the landfill to aerobic degradation in the following manner: (1) injecting air via the landfill leachate collection system (2) injecting air via vertical air injection wells installed within the waste mass; (3) applying leachate to the waste mass using a pressurized drip irrigation system; (4) allowing landfill gases to vent; and (5) adjusting air injection and recirculated leachate to achieve a 40% to 60% moisture level and a temperature between 120.degree. F. and 140.degree. F. in steady state.

  14. Aerobic landfill bioreactor

    DOE Patents [OSTI]

    Hudgins, Mark P; Bessette, Bernard J; March, John; McComb, Scott T.

    2000-01-01

    The present invention includes a method of decomposing municipal solid waste (MSW) within a landfill by converting the landfill to aerobic degradation in the following manner: (1) injecting air via the landfill leachate collection system (2) injecting air via vertical air injection wells installed within the waste mass; (3) applying leachate to the waste mass using a pressurized drip irrigation system; (4) allowing landfill gases to vent; and (5) adjusting air injection and recirculated leachate to achieve a 40% to 60% moisture level and a temperature between 120.degree. F. and 140.degree. F. in steady state.

  15. ORISE: Data Collection and Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Data Collection and Analysis The Oak Ridge Institute for Science and Education (ORISE) assists government agencies and organizations in acquiring evidence from systematic data collection procedures and analyzing data before, during and after program implementation. ORISE performs data analysis and collection using one or more of the following tactics: Primary and secondary literature reviews Environmental scans Focus groups Key informant interview Surveys and questionnaires Media analysis and

  16. ORISE: Data Collection and Analysis

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and collection using one or more of the following tactics: Primary and secondary literature reviews Environmental scans Focus groups Key informant interview Surveys and...

  17. Introduction to BPA Film Collection

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of Information Act Investor Relations Library Privacy Publications Tribal Affairs Introduction to BPA Film Collection: Volume One, Disc One, 1939-1954 An error occurred. Try...

  18. EM Launches Comprehensive Flickr Collection

    Broader source: Energy.gov [DOE]

    WASHINGTON, D.C. EM recently established an EM Flickr Collection, which organizes over 1,100 photos from around the EM complex.

  19. Collective neutrino oscillations in supernovae

    SciTech Connect (OSTI)

    Duan, Huaiyu [Department of Physics and Astronomy, University of New Mexico, Albuquerque, NM 87131 (United States)

    2014-06-24

    In a dense neutrino medium neutrinos can experience collective flavor transformation through the neutrino-neutrino forward scattering. In this talk we present some basic features of collective neutrino flavor transformation in the context in core-collapse supernovae. We also give some qualitative arguments for why and when this interesting phenomenon may occur and how it may affect supernova nucleosynthesis.

  20. Microsoft Word - Appendix I-LCRS Operating Plan.doc

    Office of Legacy Management (LM)

    July 2005 Doc. No. S0079000 Page I-3 I1.0 Purpose The purpose of this document is to provide information necessary for the proper operation and maintenance of the Leachate Collection and Removal System (LCRS). Specifically, the subsequent sections will provide the information relating to the management of leachate, maintenance and calibration of liquid level, general equipment maintenance, and reporting requirements. I2.0 Facility Description The LCRS facility is located at the north end of the

  1. Microsoft Word - Appendix J-LCRS-Train 3 Treament Contingency Plan1.doc

    Office of Legacy Management (LM)

    February 2005 Second Draft Final Doc. No. S00790AG Page I-3 I1.0 Purpose The purpose of this document is to provide information necessary for the proper operation and maintenance of the Leachate Collection and Removal System (LCRS). Specifically, the subsequent sections will provide the information relating to the management of leachate, maintenance and calibration of liquid level, general equipment maintenance, and reporting requirements. I2.0 Facility Description The LCRS facility is located

  2. NREL: Distributed Grid Integration - Data Collection and Visualization

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Projects Data Collection and Visualization Projects NREL researchers work with utilities and other organizations, such as the Sacramento Municipal Utility District and the U.S. Army, to create data collection and visualization scenarios that help them to understand and effectively manage distributed energy integration systems. Sacramento Municipal Utility District As part of a larger project with the Sacramento Municipal Utility District (SMUD), NREL is using its data collection and

  3. E P GPT collectively denotes new developments

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    E P GPT collectively denotes new developments in gener- alized perturbation theory (GPT) that place an emphasis on computational efficiency in routine design and safety reactor calculations. Over the past several decades, GPT has distinguished itself as a powerful mathematical analysis tool for estimating the variations in system response resulting from general perturbations in the model's input parameters without explicitly solving for the variations in the state variables. Unfortunately,

  4. eDPS Aerosol Collection

    SciTech Connect (OSTI)

    Venzie, J.

    2015-10-13

    The eDPS Aerosol Collection project studies the fundamental physics of electrostatic aerosol collection for national security applications. The interpretation of aerosol data requires understanding and correcting for biases introduced from particle genesis through collection and analysis. The research and development undertaken in this project provides the basis for both the statistical correction of existing equipment and techniques; as well as, the development of new collectors and analytical techniques designed to minimize unwanted biases while improving the efficiency of locating and measuring individual particles of interest.

  5. Method of concurrently filtering particles and collecting gases

    DOE Patents [OSTI]

    Mitchell, Mark A; Meike, Annemarie; Anderson, Brian L

    2015-04-28

    A system for concurrently filtering particles and collecting gases. Materials are be added (e.g., via coating the ceramic substrate, use of loose powder(s), or other means) to a HEPA filter (ceramic, metal, or otherwise) to collect gases (e.g., radioactive gases such as iodine). The gases could be radioactive, hazardous, or valuable gases.

  6. Collections

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    every field of interest affecting BPA, including "how to" computer texts, economics, geology, psychology, engineering, transmission, management and "worklife." Government...

  7. Education & Collection Facility GSHP Demonstration Project

    SciTech Connect (OSTI)

    Joplin, Jeff

    2015-03-28

    The Denver Museum of Nature & Science (DMNS) designed and implemented an innovative ground source heat pump (GSHP) system for heating and cooling its new Education and Collection Facility (ECF) building addition. The project goal was to successfully design and install an open-loop GSHP system that utilized water circulating within an underground municipal recycled (non-potable) water system as the heat sink/source as a demonstration project. The expected results were to significantly reduce traditional GSHP installation costs while increasing system efficiency, reduce building energy consumption, require significantly less area and capital to install, and be economically implemented wherever access to a recycled water system is available. The project added to the understanding of GSHP technology by implementing the first GSHP system in the United States utilizing a municipal recycled water system as a heat sink/source. The use of this fluid through a GSHP system has not been previously documented. This use application presents a new opportunity for local municipalities to develop and expand the use of underground municipal recycled (non-potable) water systems. The installation costs for this type of technology in the building structure would be a cost savings over traditional GSHP costs, provided the local municipal infrastructure was developed. Additionally, the GSHP system functions as a viable method of heat sink/source as the thermal characteristics of the fluid are generally consistent throughout the year and are efficiently exchanged through the GSHP system and its components. The use of the recycled water system reduces the area required for bore or loop fields; therefore, presenting an application for building structures that have little to no available land use or access. This GSHP application demonstrates the viability of underground municipal recycled (non-potable) water systems as technically achievable, environmentally supportive, and an efficient system.

  8. Radioisotope Detection Device and Methods of Radioisotope Collection

    DOE Patents [OSTI]

    Tranter, Troy J. (Idaho Falls, ID); Oertel, Christopher P. (Idaho Falls, ID); Giles, John R. (Pocatello, ID); Mann, Nicholas R. (Rigby, ID); McIlwain, Michael E. (Idaho Falls, ID)

    2011-04-12

    A device for collection of radionuclides includes a mixture of a polymer, a fluorescent organic scintillator and a chemical extractant. A radionuclide detector system includes a collection device comprising a mixture of a polymer, a fluorescent agent and a selective ligand. The system includes at least one photomultiplier tube (PMT). A method of detecting radionuclides includes providing a collector device comprising a mixture comprising a polymer, a fluorescent organic scintillator and a chemical extractant. An aqueous environment is exposed to the device and radionuclides are collected from the environment. Radionuclides can be concentrated within the device.

  9. Light collection device for flame emission detectors

    DOE Patents [OSTI]

    Woodruff, Stephen D. (Morgantown, WV); Logan, Ronald G. (Morgantown, WV); Pineault, Richard L. (Morgantown, WV)

    1990-01-01

    A light collection device for use in a flame emission detection system such as an on-line, real-time alkali concentration process stream monitor is disclosed which comprises a sphere coated on its interior with a highly diffuse reflective paint which is positioned over a flame emission source, and one or more fiber optic cables which transfer the light generated at the interior of the sphere to a detecting device. The diffuse scattering of the light emitted by the flame uniformly distributes the light in the sphere, and the collection efficiency of the device is greater than that obtainable in the prior art. The device of the present invention thus provides enhanced sensitivity and reduces the noise associated with flame emission detectors, and can achieve substantial improvements in alkali detection levels.

  10. Improved multiprocessor garbage collection algorithms

    SciTech Connect (OSTI)

    Newman, I.A.; Stallard, R.P.; Woodward, M.C.

    1983-01-01

    Outlines the results of an investigation of existing multiprocessor garbage collection algorithms and introduces two new algorithms which significantly improve some aspects of the performance of their predecessors. The two algorithms arise from different starting assumptions. One considers the case where the algorithm will terminate successfully whatever list structure is being processed and assumes that the extra data space should be minimised. The other seeks a very fast garbage collection time for list structures that do not contain loops. Results of both theoretical and experimental investigations are given to demonstrate the efficacy of the algorithms. 7 references.

  11. Sensitivity of nonlinear photoionization to resonance substructure in collective excitation

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Mazza, T.; Karamatskou, A.; Ilchen, M.; Bakhtiarzadeh, S.; Rafipoor, A. J.; O’Keeffe, P.; Kelly, T. J.; Walsh, N.; Costello, J. T.; Meyer, M.; et al

    2015-04-09

    Collective behaviour is a characteristic feature in many-body systems, important for developments in fields such as magnetism, superconductivity, photonics and electronics. Recently, there has been increasing interest in the optically nonlinear response of collective excitations. Here we demonstrate how the nonlinear interaction of a many-body system with intense XUV radiation can be used as an effective probe for characterizing otherwise unresolved features of its collective response. Resonant photoionization of atomic xenon was chosen as a case study. The excellent agreement between experiment and theory strongly supports the prediction that two distinct poles underlie the giant dipole resonance. Our results pavemore » the way towards a deeper understanding of collective behaviour in atoms, molecules and solid-state systems using nonlinear spectroscopic techniques enabled by modern short-wavelength light sources.« less

  12. Sensitivity of nonlinear photoionization to resonance substructure in collective excitation

    SciTech Connect (OSTI)

    Mazza, T.; Karamatskou, A.; Ilchen, M.; Bakhtiarzadeh, S.; Rafipoor, A. J.; O’Keeffe, P.; Kelly, T. J.; Walsh, N.; Costello, J. T.; Meyer, M.; Santra, R.

    2015-04-09

    Collective behaviour is a characteristic feature in many-body systems, important for developments in fields such as magnetism, superconductivity, photonics and electronics. Recently, there has been increasing interest in the optically nonlinear response of collective excitations. Here we demonstrate how the nonlinear interaction of a many-body system with intense XUV radiation can be used as an effective probe for characterizing otherwise unresolved features of its collective response. Resonant photoionization of atomic xenon was chosen as a case study. The excellent agreement between experiment and theory strongly supports the prediction that two distinct poles underlie the giant dipole resonance. Our results pave the way towards a deeper understanding of collective behaviour in atoms, molecules and solid-state systems using nonlinear spectroscopic techniques enabled by modern short-wavelength light sources.

  13. Garbage collection: an exercise in distributed, fault-tolerant programming

    SciTech Connect (OSTI)

    Vestal, S.C.

    1987-01-01

    Two garbage-collection algorithms are presented to reclaim unused storage in object-oriented systems implemented on local area networks. The algorithms are fault-tolerant and allowed parallel, incremental collection in an object address space distributed throughout the system. The two approaches allow multiple collectors, so some unused storage can be reclaimed in partitioned networks. The first method makes use of fault-tolerant reference counts together with an algorithm to collect cycles of objects that would otherwise remain unclaimed. The second method adapts a parallel collector so that it can be used to collect subspaces of the entire network address space. Throughout this work concern is with a methodology for developing distributed, parallel, fault-tolerant programs. Also, there is concern with the suitability of object-oriented systems for such applications.

  14. Records Inventory Data Collection Software

    Energy Science and Technology Software Center (OSTI)

    1995-03-01

    DATALINK was created to provide an easy to use data collection program for records management software products. It provides several useful tools for capturing and validating record index data in the field. It also allows users to easily create a comma delimited, ASCII text file for data export into most records management software products.

  15. Powder collection apparatus/method

    DOE Patents [OSTI]

    Anderson, I.E.; Terpstra, R.L.; Moore, J.A.

    1994-01-11

    Device for separating and collecting ultrafine atomized powder from the gas stream of a gas atomizing apparatus comprises a housing having an interior wall oriented at an angle relative to horizontal so as to form a downwardly converging, conical expansion chamber, an inlet conduit communicated to the expansion chamber proximate an upper region thereof for receiving the gas stream, and an outlet proximate a lower region of the expansion chamber. The inlet conduit is oriented at a compound inclined angle (with respect to horizontal) selected to promote separation and collection of powder from the gas stream in the expansion chamber. The compound angle comprises a first entrance angle that is greater than the angle of repose of the powder on the housing interior wall such that any powder accumulation in the inlet conduit tends to flow down the wall toward the outlet. The second angle is selected generally equal to the angle of the housing interior wall measured from the same horizontal plane so as to direct the gas stream into the expansion chamber generally tangent to the housing interior wall to establish a downward swirling gas stream flow in the expansion chamber. A powder collection container is communicated to the outlet of the expansion chamber to collect the powder for further processing. 4 figures.

  16. The Process Manager Collective Library

    Energy Science and Technology Software Center (OSTI)

    2009-02-26

    The PMGR_COLLECTIVE library provides an interface that MPI implemenataions may call to initialize ranks in a scalable way. It was developed to reduce the startup time MPI appkications, however, other tools such as debugger infrastructures have also found use cases for it. When first developed, it reduced the startup time from 15 minutes to 10 seconds on as 8192-node cluster.

  17. Solar photovoltaic reflective trough collection structure

    DOE Patents [OSTI]

    Anderson, Benjamin J.; Sweatt, William C.; Okandan, Murat; Nielson, Gregory N.

    2015-11-19

    A photovoltaic (PV) solar concentration structure having at least two troughs encapsulated in a rectangular parallelepiped optical plastic structure, with the troughs filled with an optical plastic material, the troughs each having a reflective internal surface and approximately parabolic geometry, and the troughs each including photovoltaic cells situated so that light impinging on the optical plastic material will be concentrated onto the photovoltaic cells. Multiple structures can be connected to provide a solar photovoltaic collection system that provides portable, efficient, low-cost electrical power.

  18. Argon Collection And Purification For Proliferation Detection

    SciTech Connect (OSTI)

    Achey, R.; Hunter, D.

    2015-10-09

    In order to determine whether a seismic event was a declared/undeclared underground nuclear weapon test, environmental samples must be taken and analyzed for signatures that are unique to a nuclear explosion. These signatures are either particles or gases. Particle samples are routinely taken and analyzed under the Comprehensive Nuclear-Test-Ban Treaty Organization (CTBTO) verification regime as well as by individual countries. Gas samples are analyzed for signature gases, especially radioactive xenon. Underground nuclear tests also produce radioactive argon, but that signature is not well monitored. A radioactive argon signature, along with other signatures, can more conclusively determine whether an event was a nuclear test. This project has developed capabilities for collecting and purifying argon samples for ultra-low-background proportional counting. SRNL has developed a continuous gas enrichment system that produces an output stream containing 97% argon from whole air using adsorbent separation technology (the flow diagram for the system is shown in the figure). The vacuum swing adsorption (VSA) enrichment system is easily scalable to produce ten liters or more of 97% argon within twelve hours. A gas chromatographic separation using a column of modified hydrogen mordenite molecular sieve has been developed that can further purify the sample to better than 99% purity after separation from the helium carrier gas. The combination of these concentration and purification systems has the capability of being used for a field-deployable system for collecting argon samples suitable for ultra-low-background proportional counting for detecting nuclear detonations under the On-Site Inspection program of the CTBTO verification regime. The technology also has applications for the bulk argon separation from air for industrial purposes such as the semi-conductor industry.

  19. Multi-input and binary reproducible, high bandwidth floating point adder in a collective network

    DOE Patents [OSTI]

    Chen, Dong; Eisley, Noel A; Heidelberger, Philip; Steinmacher-Burow, Burkhard

    2015-03-10

    To add floating point numbers in a parallel computing system, a collective logic device receives the floating point numbers from computing nodes. The collective logic devices converts the floating point numbers to integer numbers. The collective logic device adds the integer numbers and generating a summation of the integer numbers. The collective logic device converts the summation to a floating point number. The collective logic device performs the receiving, the converting the floating point numbers, the adding, the generating and the converting the summation in one pass. One pass indicates that the computing nodes send inputs only once to the collective logic device and receive outputs only once from the collective logic device.

  20. Training Needs Assessment (TNA) Data Collection Tool

    Broader source: Energy.gov [DOE]

    The TNA Data Collection Tool Instructions provides guidance on how to complete the TNA Data Collection Tool. The TNA Data Collection Tool is an Excel spreadsheet that the organization's designating training POC will use to populate their organizations training needs.

  1. Broadcasting collective operation contributions throughout a parallel computer

    DOE Patents [OSTI]

    Faraj, Ahmad (Rochester, MN)

    2012-02-21

    Methods, systems, and products are disclosed for broadcasting collective operation contributions throughout a parallel computer. The parallel computer includes a plurality of compute nodes connected together through a data communications network. Each compute node has a plurality of processors for use in collective parallel operations on the parallel computer. Broadcasting collective operation contributions throughout a parallel computer according to embodiments of the present invention includes: transmitting, by each processor on each compute node, that processor's collective operation contribution to the other processors on that compute node using intra-node communications; and transmitting on a designated network link, by each processor on each compute node according to a serial processor transmission sequence, that processor's collective operation contribution to the other processors on the other compute nodes using inter-node communications.

  2. The Solarize Guidebook: A community guide to collective purchasing of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    residential PV systems (Book), SunShot, U.S. Department of Energy (DOE) | Department of Energy The Solarize Guidebook: A community guide to collective purchasing of residential PV systems (Book), SunShot, U.S. Department of Energy (DOE) The Solarize Guidebook: A community guide to collective purchasing of residential PV systems (Book), SunShot, U.S. Department of Energy (DOE) This guidebook is intended as a road map for project planners and solar advocates who want to convert

  3. collecting reliability and performance data

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    collecting reliability and performance data - Sandia Energy Energy Search Icon Sandia Home Locations Contact Us Employee Locator Energy & Climate Secure & Sustainable Energy Future Stationary Power Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 Geothermal Natural Gas Safety, Security & Resilience of the Energy Infrastructure Energy Storage Nuclear Power & Engineering Grid Modernization Battery Testing Nuclear Fuel Cycle Defense Waste

  4. Apparatus for collecting solar energy

    SciTech Connect (OSTI)

    Wildenrotter, K.

    1981-08-18

    Apparatus is described for collecting solar energy comprises a collector having a solar-energy collector surface. The collector is mounted on a support and is pivotable between an exposed position in which the collector surface faces the sun and a substantially horizontal sheltered position in which the collector surface faces the earth, thereby protecting the collector surface from the elements and facilitating access thereto for maintenance.

  5. Collecting Personally Identifiable Information Through the Web...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Federal Requirements Collecting Personally Identifiable Information Through the Web and User Research Collecting Personally Identifiable Information Through the Web and User ...

  6. Advances in understanding solar energy collection materials

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Understanding solar energy collection materials Advances in understanding solar energy collection materials A LANL team and collaborators have made advances in the understanding of...

  7. Geothermal Data Development, Collection, and Maintenance | Open...

    Open Energy Info (EERE)

    Data Development, Collection, and Maintenance Jump to: navigation, search Geothermal ARRA Funded Projects for Geothermal Data Development, Collection, and Maintenance Loading...

  8. Strategies for Collecting Household Energy Data | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Collecting Household Energy Data Strategies for Collecting Household Energy Data Better Buildings Neighborhood Program Data and Evaluation Peer Exchange Call: Strategies for ...

  9. Analysis of the Multi-Phase Copying Garbage Collection Algorithm

    SciTech Connect (OSTI)

    Podhorszki, Norbert

    2009-01-01

    The multi-phase copying garbage collection was designed to avoid the need for large amount of reserved memory usually required for the copying types of garbage collection algorithms. The collection is performed in multiple phases using the available free memory. This paper proves that the number of phases depends on the size of the reserved memory and the ratio of the garbage and accessible objects. The performance of the implemented algorithm is tested in a fine-grained parallel Prolog system. We find that reserving only 10% of memory for garbage collection is sufficient for good performance in practice. Additionally, an improvement of the generic algorithm specifically for the tested parallel Prolog system is described.

  10. GPS Travel Survey Data Collection and Analysis | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    GPS Travel Survey Data Collection and Analysis GPS Travel Survey Data Collection and Analysis 2009 DOE Hydrogen Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting, May 18-22, 2009 -- Washington D.C. PDF icon vssp_08_markel.pdf More Documents & Publications Route-Based Controls Potential for Efficiency Gains Light Duty Plug-in Hybrid Vehicle Systems Analysis Heavy-Duty Vehicle Field Evaluations

  11. Truck Duty Cycle and Performance Data Collection and Analysis Program |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy 0 DOE Vehicle Technologies and Hydrogen Programs Annual Merit Review and Peer Evaluation Meeting, June 7-11, 2010 -- Washington D.C. PDF icon vss002_knee_2010_o.pdf More Documents & Publications Heavy Duty & Medium Duty Drive Cycle Data Collection for Modeling Expansion Truck Duty Cycle and Performance Data Collection and Analysis Program 2010 DOE EERE Vehicle Technologies Program Merit Review - Vehicle Systems Sim

  12. THE WORLD'S Biggest Fan Collection

    Energy Savers [EERE]

    WORLD'S Biggest Fan Collection If you only know the Big Ass Fan Company as the preeminent designer and manufacturer of high volume, low speed fans for factories and cows, it's time you get to know us better. While we continue to lead the way in industrial and agricultural air movement, we've also refined these designs to bring the same innovation and benefits of our famous fans to circulate an ocean of air in sound-sensitive commercial spaces and homes. And when our customers said they wanted

  13. PMGR_COLLECTIVE V1.0

    Energy Science and Technology Software Center (OSTI)

    002339WKSTN00 The Process Manager Collective Library http://sourceforge.net/projects/pmgrcollective/

  14. ORISE: Worker Health Studies - Radiation Exposure Data Collection

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    How ORISE is Making a Difference Overview Argonne Electronic Medical Records System Beryllium Testing and Surveillance Radiation Exposure Information and Reporting System (REIRS) U.S. Department of Energy Radiation Exposure Monitoring System (REMS) DOE IISP 10-Year Summary Report Resources Overview Reports Peer-Reviewed Journal Articles Human Subjects Resource Book How to Work With Us Contact Us Oak Ridge Institute for Science Education Radiation Exposure Data Collection ORISE manages large,

  15. Matrix isolation apparatus with extended sample collection capability

    DOE Patents [OSTI]

    Reedy, Gerald T. (Bourbonnais, IL)

    1987-01-01

    A gas-sample collection device provides for the matrix isolation of increased amounts of a sample material for spectrographic analysis from a gas chromatographic separation. The device includes an evacuated sample collection chamber containing a disc-like specular carousel having a generally circular lateral surface upon which the sample is deposited in an inert gas matrix for infrared (IR) spectral analysis. The evacuated sample chamber is mounted in a fixed manner and is coupled to and supports a rotating cryostatic coupler which, in turn, supports the specular carousel within the collection chamber. A rotational drive system connected to the cryostatic coupler provides for its rotational displacement as well as that of the sample collecting carousel. In addition, rotation of the cryostatic coupler effects vertical displacement of the carousel to permit the collection of an extended sample band in a helical configuration on the entire lateral surface of the carousel. The various components of the carousel's angular/linear displacement drive system are located exterior to the cryostatic coupler for easy access and improved operation. The cryostatic coupler includes a 360.degree. rotary union assembly for permitting the delivery of a high pressure working fluid to the cryostatic coupler in a continuous flow manner for maintaining the specular carousel at a low temperature, e.g., 10.degree.-20.degree. K., for improved uninterrupted gas sample collection and analysis.

  16. Devices for collecting chemical compounds

    DOE Patents [OSTI]

    Scott, Jill R; Groenewold, Gary S

    2013-12-24

    A device for sampling chemical compounds from fixed surfaces and related methods are disclosed. The device may include a vacuum source, a chamber and a sorbent material. The device may utilize vacuum extraction to volatilize the chemical compounds from a fixed surface so that they may be sorbed by the sorbent material. The sorbent material may then be analyzed using conventional thermal desorption/gas chromatography/mass spectrometry (TD/GC/MS) instrumentation to determine presence of the chemical compounds. The methods may include detecting release and presence of one or more chemical compounds and determining the efficacy of decontamination. The device may be useful in collection and analysis of a variety of chemical compounds, such as residual chemical warfare agents, chemical attribution signatures and toxic industrial chemicals.

  17. The Collective Atomic Recoil Laser

    SciTech Connect (OSTI)

    Courteille, Ph.W.; Cube, C. avon; Deh, B.; Kruse, D.; Ludewig, A.; Slama, S.; Zimmermann, C.

    2005-05-05

    An ensemble of periodically ordered atoms coherently scatters the light of an incident laser beam. The scattered and the incident light may interfere and give rise to a light intensity modulation and thus to optical dipole forces which, in turn, emphasize the atomic ordering. This positive feedback is at the origin of the collective atomic recoil laser (CARL). We demonstrate this dynamics using ultracold atoms confined by dipole forces in a unidirectionally pumped far red-detuned high-finesse optical ring cavity. Under the influence of an additional dissipative force exerted by an optical molasses the atoms, starting from an unordered distribution, spontaneously form a density grating moving at constant velocity. Additionally, steady state lasing is observed in the reverse direction if the pump laser power exceeds a certain threshold. We compare the dynamics of the atomic trajectories to the behavior of globally coupled oscillators, which exhibit phase transitions from incoherent to coherent states if the coupling strength exceeds a critical value.

  18. Data Collection, Analysis, and Reporting | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Business Operations Project Management Coordination Office Data Collection, Analysis, and Reporting Data Collection, Analysis, and Reporting The Data Collection, Analysis,...

  19. Collective cell motion | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Collective cell motion Share Topic Programs Materials science Materials simulation & theory Mathematics, computing, & computer science Modeling, simulation, & visualization Over...

  20. Emissions from US waste collection vehicles

    SciTech Connect (OSTI)

    Maimoun, Mousa A.; Reinhart, Debra R.; Gammoh, Fatina T.; McCauley Bush, Pamela

    2013-05-15

    Highlights: ? Life-cycle emissions for alternative fuel technologies. ? Fuel consumption of alternative fuels for waste collection vehicles. ? Actual driving cycle of waste collection vehicles. ? Diesel-fueled waste collection vehicle emissions. - Abstract: This research is an in-depth environmental analysis of potential alternative fuel technologies for waste collection vehicles. Life-cycle emissions, cost, fuel and energy consumption were evaluated for a wide range of fossil and bio-fuel technologies. Emission factors were calculated for a typical waste collection driving cycle as well as constant speed. In brief, natural gas waste collection vehicles (compressed and liquid) fueled with North-American natural gas had 610% higher well-to-wheel (WTW) greenhouse gas (GHG) emissions relative to diesel-fueled vehicles; however the pump-to-wheel (PTW) GHG emissions of natural gas waste collection vehicles averaged 6% less than diesel-fueled vehicles. Landfill gas had about 80% lower WTW GHG emissions relative to diesel. Biodiesel waste collection vehicles had between 12% and 75% lower WTW GHG emissions relative to diesel depending on the fuel source and the blend. In 2011, natural gas waste collection vehicles had the lowest fuel cost per collection vehicle kilometer travel. Finally, the actual driving cycle of waste collection vehicles consists of repetitive stops and starts during waste collection; this generates more emissions than constant speed driving.

  1. Draft Sample Collection Instrument | Department of Energy

    Office of Environmental Management (EM)

    Draft Sample Collection Instrument Draft Sample Collection Instrument Davis-Bacon Semi-annual Labor Compliance Report OMB Control Number 1910-New PDF icon dba_collection_instrument_mock_up.pdf More Documents & Publications SEMI-ANNUAL DAVIS-BACON ENFORCEMENT REPORT SEMI-ANNUAL DAVIS-BACON ENFORCEMENT REPORT Labor Standards/Wage and Hour Laws

  2. A hybrid hydrologic-geophysical inverse technique for the assessment and monitoring of leachates in the vadose zone. 1998 annual progress report

    SciTech Connect (OSTI)

    Alumbaugh, D.L.; Glass, R.J.; Yeh, T.C.; LaBrecque, D.

    1998-06-01

    'The objective of this study is to develop and field test a new, integrated Hybrid Hydrologic-Geophysical Inverse Technique (HHGIT) for characterization of the vadose zone at contaminated sites. This new approach to site characterization and monitoring can provide detailed maps of hydrogeological heterogeneity and the extent of contamination by combining information from electric resistivity tomography (ERT) surveys, statistical information about heterogeneity and hydrologic processes, and sparse hydrologic data. Because the electrical conductivity of the vadose zone (from the ERT measurements) can be correlated to the fluid saturation and/or contaminant concentration, the hydrologic and geophysical measurements are related. As of the 21st month of a 36-month project, a three-dimensional stochastic hydrologic inverse model for heterogeneous vadose zones has been developed. This model employs pressure and moisture content measurements under both transient and steady flow conditions to estimate unsaturated hydraulic parameters. In this model, an innovative approach to sequentially condition the estimate using temporal measurements has been incorporated. This allows us to use vast amounts of pressure and moisture content information measured at different times while keeping the computational effort manageable. Using this model the authors have found that the relative importance of the pressure and moisture content measurements in defining the different vadose zone parameters depends on whether the soil is wet or dry. They have also learned that pressure and moisture content measurements collected during steady state flow provide the best characterization of heterogeneity compared to other types of hydrologic data. These findings provide important guidance to the design of sampling scheme of the field experiment described below.'

  3. Microsoft Word - IEEEFieldDataCollectionPaperRev2.doc

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    FIELD DATA COLLECTION FOR QUANTIFICATION OF RELIABILITY AND AVAILABILITY FOR PHOTOVOLTAIC SYSTEMS Elmer Collins, Jeff Mahn, Michael Mundt, Jennifer Granata and Michael Quintana Sandia National Laboratories PO Box 5800, Albuquerque, New Mexico, 87185-1033 ABSTRACT Predicting reliability and availability is a data driven capability of interest to the entire photovoltaic community, from material suppliers to system owners. Sandia National Laboratories is developing a predictive model and a host of

  4. Collecting and Characterizing Validation Data

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and Characterizing Validation Data to Support Advanced Simulation of Nuclear Reactor Hydraulics Nam Dinh North Carolina State University Anh Bui Idaho National Laboratory Hyung Lee Bettis Laboratory ASME 2013 Verification and Validation Symposium Las Vegas, NV, May 22-24, 2013 Multi-Physics, Multi-Scale Problem Validation Hierarchy (Validation Pyramid) of Subcooled Boiling Flow Model Bayesian Framework for Data Integration Nuclear System Analysis - Subcooled Boiling Flow Example * Underlying

  5. Quasi-isochronous muon collection channels

    SciTech Connect (OSTI)

    Ankenbrandt, Charles M.; Neuffer, David; Johnson, Rolland P.

    2015-04-26

    Intense muon beams have many potential commercial and scientific applications, ranging from low-energy investigations of the basic properties of matter using spin resonance to large energy-frontier muon colliders. However, muons originate from a tertiary process that produces a diffuse swarm. To make useful beams, the swarm must be rapidly captured and cooled before the muons decay. In this STTR project a promising new concept for the collection and cooling of muon beams to increase their intensity and reduce their emittances was investigated, namely, the use of a nearly isochronous helical cooling channel (HCC) to facilitate capture of the muons into RF bunches. The muon beam can then be cooled quickly and coalesced efficiently to optimize the luminosity of a muon collider, or could provide compressed muon beams for other applications. Optimal ways to integrate such a subsystem into the rest of a muon collection and cooling system, for collider and other applications, were developed by analysis and simulation. The application of quasi-isochronous helical cooling channels (QIHCC) for RF capture of muon beams was developed. Innovative design concepts for a channel incorporating straight solenoids, a matching section, and an HCC, including RF and absorber, were developed, and its subsystems were simulated. Additionally, a procedure that uses an HCC to combine bunches for a muon collider was invented and simulated. Difficult design aspects such as matching sections between subsystems and intensity-dependent effects were addressed. The bunch recombination procedure was developed into a complete design with 3-D simulations. Bright muon beams are needed for many commercial and scientific reasons. Potential commercial applications include low-dose radiography, muon catalyzed fusion, and the use of muon beams to screen cargo containers for homeland security. Scientific uses include low energy beams for rare process searches, muon spin resonance applications, muon beams for neutrino factories, and muon colliders as Higgs factories or energy-frontier discovery machines.

  6. Installation of reactive metals groundwater collection and treatment systems

    SciTech Connect (OSTI)

    Hopkins, J.K.; Primrose, A.L.; Vogan, J.; Uhland, J.

    1998-07-01

    Three groundwater plumes contaminated with volatile organic compounds (VOCs) and radionuclides at the Rocky Flats Environmental Technology Site are scheduled for remediation by 1999 based on the Rocky Flats Cleanup Agreement (RFCA) (DOE, 1996). These three plumes are among the top 20 environmental cleanup sites at Rocky Flats. One of these plumes, the Mound Site Plume, is derived from a previous drum storage area, and daylights as seeps near the South Walnut Creek drainage. Final design for remediation of the Mound Site Plume has been completed based on use of reactive metals to treat the contaminated groundwater, and construction is scheduled for early 1998. The two other plumes, the 903 Pad/Ryan`s Pit and the East Trenches Plumes, are derived from VOCs either from drums that leaked or that were disposed of in trenches. These two plumes are undergoing characterization and conceptual design in 1998 and construction is scheduled in 1999. The contaminants of concern in these plumes are tetrachloroethene, trichloroethene, carbon tetrachloride and low levels of uranium and americium.

  7. NW-MILO Acoustic Data Collection

    SciTech Connect (OSTI)

    Matzner, Shari; Myers, Joshua R.; Maxwell, Adam R.; Jones, Mark E.

    2010-02-17

    There is an enduring requirement to improve our ability to detect potential threats and discriminate these from the legitimate commercial and recreational activity ongoing in the nearshore/littoral portion of the maritime domain. The Northwest Maritime Information and Littoral Operations (NW-MILO) Program at PNNLs Coastal Security Institute in Sequim, Washington is establishing a methodology to detect and classify these threats - in part through developing a better understanding of acoustic signatures in a near-shore environment. The purpose of the acoustic data collection described here is to investigate the acoustic signatures of small vessels. The data is being recorded continuously, 24 hours a day, along with radar track data and imagery. The recording began in August 2008, and to date the data contains tens of thousands of signals from small vessels recorded in a variety of environmental conditions. The quantity and variety of this data collection, with the supporting imagery and radar track data, makes it particularly useful for the development of robust acoustic signature models and advanced algorithms for signal classification and information extraction. The underwater acoustic sensing system is part of a multi-modal sensing system that is operating near the mouth of Sequim Bay. Sequim Bay opens onto the Straight of Juan de Fuca, which contains part of the border between the U.S. and Canada. Table 1 lists the specific components used for the NW-MILO system. The acoustic sensor is a hydrophone permanently deployed at a mean depth of about 3 meters. In addition to a hydrophone, the other sensors in the system are a marine radar, an electro-optical (EO) camera and an infra-red (IR) camera. The radar is integrated with a vessel tracking system (VTS) that provides position, speed and heading information. The data from all the sensors is recorded and saved to a central server. The data has been validated in terms of its usability for characterizing the signatures of small vessels. The sampling rate of 8 kHz and low pass filtering to 2 kHz results in an alias-free signal in the frequency band that is appropriate for small vessels. Calibration was performed using a Lubell underwater speaker so that the raw data signal levels can be converted to sound pressure. Background noise is present due to a nearby pump and as a result of tidal currents. More study is needed to fully characterize the noise, but it does not pose an obstacle to using the acoustic data for the purposes of vessel detection and signature analysis. The detection range for a small vessel was estimated using the calibrated voltage response of the system and a cylindrical spreading model for transmission loss. The sound pressure of a typical vessel with an outboard motor was found to be around 140 dB mPa, and could theoretically be detected from 10 km away. In practical terms, a small vessel could reliably be detected from 3 - 5 km away. The data is archived in netCDF files, a standard scientific file format that is "self describing". This means that each data file contains the metadata - timestamps, units, origin, etc. - needed to make the data meaningful and portable. Other file formats, such as XML, are also supported. A visualization tool has been developed to view the acoustic data in the form of spectrograms, along with the coincident radar track data and camera images.

  8. Geothermal Academy: Focus Center for Data Collection, Analysis, and Dissemination

    SciTech Connect (OSTI)

    Nakagawa, Masami, Ph.D.; Fujiono, Hendro, Ph.D.; McCartney, John S., Ph.D.; Reed, Adam, J.D., Esq.

    2011-10-31

    Geothermal Academy: A Pathway for Confirmation of Ground-Source Heat Pumps in the United States. In 2008, Oak Ridge National Laboratory issued a report on geothermal heats pumps (GHPs) focused on the market status, barriers to adoption, and actions to overcome these barriers (Hughes 2008). Of the barriers raised in this report, of the most pressing is the lack of performance and energy usage data for GHPs. Further, an associated barrier is a lack of a fair comparison of the energy usage of conventional heating and cooling systems for the same building. Because of these barriers, we are not able to say how much energy is used by well-designed GHP systems on a long-term basis, nor are we able to say how better their energy usage is compared to conventional systems. The need for a fair comparison with conventional systems is particularly relevant as modern versions of conventional air conditioners, gas furnaces, and boilers have also incorporated energy saving technologies. As a first step to address this barrier, the Geothermal Academy has developed a framework for data collection. This framework has already been applied to several geothermal installations in Colorado (Nakagawa etal. 2010). The framework classifies data into different categories based on the relevance of the dat to understanding the energy consumption of a GHP system. The categories are: direct energy consumption data, heat exchange performance data, and GHP design parameter data. The main recommendation of this project is to include a minimal data collection system on each heat pump installed in the U.S., capable of measuring the electrical energy consumed, the entering/exiting fluid temperatures, and circulation rates. This is a viable and cost effective solution which will provide performance data, as data collection systems are only a fraction of the cost of a GHP unit and modern GHP units already incorporate sensors to monitor energy usage and the entering and exiting fluid temperatures. Specifically, these sensors are used to control the GHP unit to provide the heat exchange required to provide a desired temperature within a building. Accordingly, it is straightforward for this operational data to be collected to start building a database of GHP performance such that can provide statistically relevant comparison with other heating and cooling systems. In addition to collecting the data, such a system could be easily implemented with a wireless transmitter so that data could be sent to a home PC where it could be transmitted to a central database. Display of the data on a user's PC would provide feedback on the performance of their system which could perhaps refine their use of the system to reach their personal energy goals. Although a system such as that described above has yet to be incorporated directly into commercial GHP systems, it is straightforward and inexpensive to outfit a GHP with a data acquisition system and supplemental sensors. A secondary recommendation is to consider funding a pilot effort that will collect the energy and performance time series data from a representative sample of installations. A preliminary pilot effort was undertaken by the Geothermal Academy at a middle school in Ft. Collins, Colorado, which demonstrated the feasibility and ease of such an effort. A full-scale pilot effort would be most suited to evaluate the performance of GHP installations in different climate settings, preferably focusing on residential, commercial, and public buildings. If a full-scale pilot effort were to be undertaken, it is recommended to also identify large buildings which may incorporate a back-up conventional heating and cooling system in order to provide statistically relevant comparison data to assess the improvement in GHP energy usage over other heating and cooling technologies. Such a data collection system would provide several benefits to the different sectors of society (consumers, installers, policy makers, researchers, utility companies, government regulators) which are concerned with GHP technology and implementation.

  9. Containment System Michael F

    Office of Scientific and Technical Information (OSTI)

    ... in the blender or conveying system must be collected and handled as a dilute pesticidefertilizer mixture. Spilled materials and product cleaned from the blender should be ...

  10. Data Collection and Analysis | Department of Energy

    Energy Savers [EERE]

    Services » Data Collection and Analysis Data Collection and Analysis The Office of Technology Transitions tracks more than 70 technology transfer-related metrics from across all of DOE’s laboratories, sites, and facilities. The Office of Technology Transitions tracks more than 70 technology transfer-related metrics from across all of DOE's laboratories, sites, and facilities. Data collection and analysis is one of the three pillars of the Office of Technology Transitions (OTT). Every year,

  11. Collective Bargaining Agreement | Department of Energy

    Office of Environmental Management (EM)

    Collective Bargaining Agreement Collective Bargaining Agreement This collective bargaining agreement is entered into to prescribe certain rights and obligations of the employees of the Department of Energy (DOE) Headquarters represented by the National Treasury Employees Union and to delineate procedures which are designed to meet the special requirements and needs of DOE Headquarters. The provisions of this agreement have been negotiated and should be interpreted in a manner consistent with the

  12. Department of Energy Proposed Agency Information Collection:...

    Broader source: Energy.gov (indexed) [DOE]

    Department of Energy proposed Agency Information Collection: The Department of Energy (DOE) invites public comment on DOE's request to the Office of Management and Budget (OMB) to...

  13. Proposed Agency Information Collection: Federal Register Notice...

    Broader source: Energy.gov (indexed) [DOE]

    the Office of Management and Budget (OMB) to extend for three years the emergency Information Collection Request Title: OE Recovery Act Financial Assistance Grants, OMB Control...

  14. Proposed Agency Information Collection: Federal Register Notice...

    Office of Environmental Management (EM)

    54 - Aug. 10, 2011 Proposed Agency Information Collection: Federal Register Notice Volume 76, No. 154 - Aug. 10, 2011 The Department of Energy (DOE) invites public comment on DOE's...

  15. Information Collection Management | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    unless the ICR is related to statistical energy information collections and customer surveys which is handled by the Energy Information Administration. Provided below are PRA...

  16. Co-collection: Back to the past

    SciTech Connect (OSTI)

    Miller, C.

    1995-10-01

    In the early `70s, when haulers began collecting newspapers for recycling at the curbside, they collected them at the same time and with the same truck as garbage. A rack underneath the compactor truck or a trailer behind the truck held the newspaper. These early rack and trailer programs had several advantages. Racks and trailers were easy to install and maintain. In addition, they allowed the hauler to combine garbage and recyclables collection. However, both racks and trailers had limited capacity.time-consuming, off-route unloading was common. They were also unsuited for multi-material recycling. As haulers began collecting glass and metals at the curbside, co-collection was displaced by separate collection of recyclables. Today, curbside recycling is firmly established in communities throughout the US. In an attempt to lower costs, haulers are starting to use co-collection trucks to combine recyclables and garbage collection. While co-collection of recyclables and garbage is still uncommon, its advocates argue it is the wave of the future.

  17. Parallel garbage collection without synchronization overhead. Technical report

    SciTech Connect (OSTI)

    Patel, J.H.

    1984-08-01

    Incremental garbage-collection schemes incur substantial overhead that is directly translated as reduced execution efficiency for the user. Parallel garbage-collection schemes implemented via time-slicing on a serial processor also incur this overhead, which might even be aggravated due to context switching. It is useful, therefore, to examine the possibility of implementing a parallel garbage-collection algorithm using a separate processor operating asynchronously with the main-list processor. The overhead in such a scheme arises from the synchronization necessary to manage the two processors, maintaining memory consistency. In this paper, the authors present an architecture and supporting parallel garbage-collection algorithms designed for a virtual memory system with separate processors for list processing and for garbage collection. Each processor has its own primary memory; in addition, there is a small common memory which both processors may access. Individual memories swap off a common secondary memory, but no locking mechanism is required. In particular, a page may reside in both memories simultaneously, and indeed may be accessed and modified freely by each processor. A secondary memory controller ensures consistency without necessitating numerous lockouts on the pages.

  18. Wireless technology collects real-time information from oil and gas wells

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Wireless technology collects real-time information from oil and gas wells Wireless technology collects real-time information from oil and gas wells The patented system delivers continuous electromagnetic data on the reservoir conditions, enabling economical and effective monitoring and analysis. April 3, 2012 One of several active projects, LANL and Chevron co-developed INFICOMM(tm), a wireless technology used to collect real-time temperature and pressure information from sensors in oil and gas

  19. Item Management Control System

    Energy Science and Technology Software Center (OSTI)

    1993-08-06

    The Item Management Control System (IMCS) has been developed at Idaho National Engineering Laboratory to assist in organizing collections of documents using an IBM-PC or similar DOS system platform.

  20. Internal Benchmarking Outreach and Data Collection Techniques

    Broader source: Energy.gov [DOE]

    U.S. Department of Energy (DOE) Technical Assistance Program (TAP) presentation at a TAP webinar held on April 11, 2013 and dealing with internal benchmarking outreach and data collection techniques.

  1. Advances in understanding solar energy collection materials

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Understanding solar energy collection materials Advances in understanding solar energy collection materials A LANL team and collaborators have made advances in the understanding of how carbon nanotubes move charges created by light. November 9, 2012 Efficient energy transport in photovoltaic carbon nanomaterials Efficient energy transport in photovoltaic carbon nanomaterials. A LANL team and collaborators have made advances in the understanding of how carbon nanotubes move charges created by

  2. Information Collection Management | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Information Collection Management Information Collection Management Forms44.jpg The Paperwork Reduction Act (PRA) of 1995 requires federal agencies and government-owned, contractor-operated facilities to obtain approval from the Office of Management and Budget (OMB) before requesting most types of information from the public, including forms, interviews, and record-keeping requirements, among others. DOE's Chief Information Officer (CIO) is the Senior Official responsible for DOE PRA compliance.

  3. Coherent neutron scattering and collective dynamics on mesoscale

    SciTech Connect (OSTI)

    Novikov, Vladimir [ORNL; Schweizer, Kenneth S [ORNL; Sokolov, Alexei P [ORNL

    2013-01-01

    By combining, and modestly extending, a variety of theoretical concepts for the dynamics of liquids in the supercooled regime, we formulate a simple analytic model for the temperature and wavevector dependent collective density fluctuation relaxation time that is measurable using coherent dynamic neutron scattering. Comparison with experiments on the ionic glass-forming liquid Ca K NO3 in the lightly supercooled regime suggests the model captures the key physics in both the local cage and mesoscopic regimes, including the unusual wavevector dependence of the collective structural relaxation time. The model is consistent with the idea that the decoupling between diffusion and viscosity is reflected in a different temperature dependence of the collective relaxation time at intermediate wavevectors and near the main (cage) peak of the static structure factor. More generally, our analysis provides support for the ideas that decoupling information and growing dynamic length scales can be at least qualitatively deduced by analyzing the collective relaxation time as a function of temperature and wavevector, and that there is a strong link between dynamic heterogeneity phenomena at the single and many particle level. Though very simple, the model can be applied to other systems, such as molecular liquids.

  4. Financial Metrics Data Collection Protocol, Version 1.0

    SciTech Connect (OSTI)

    Fowler, Kimberly M.; Gorrissen, Willy J.; Wang, Na

    2010-04-30

    Brief description of data collection process and plan that will be used to collect financial metrics associated with sustainable design.

  5. Reducing collective quantum state rotation errors with reversible dephasing

    SciTech Connect (OSTI)

    Cox, Kevin C.; Norcia, Matthew A.; Weiner, Joshua M.; Bohnet, Justin G.; Thompson, James K.

    2014-12-29

    We demonstrate that reversible dephasing via inhomogeneous broadening can greatly reduce collective quantum state rotation errors, and observe the suppression of rotation errors by more than 21?dB in the context of collective population measurements of the spin states of an ensemble of 2.110{sup 5} laser cooled and trapped {sup 87}Rb atoms. The large reduction in rotation noise enables direct resolution of spin state populations 13(1) dB below the fundamental quantum projection noise limit. Further, the spin state measurement projects the system into an entangled state with 9.5(5) dB of directly observed spectroscopic enhancement (squeezing) relative to the standard quantum limit, whereas no enhancement would have been obtained without the suppression of rotation errors.

  6. Collection and recycling of electronic scrap: A worldwide overview and comparison with the Brazilian situation

    SciTech Connect (OSTI)

    Reis de Oliveira, Camila; Moura Bernardes, Andrea; Gerbase, Annelise Engel

    2012-08-15

    Highlights: Black-Right-Pointing-Pointer Review of the different e-waste collection systems and recycling processes. Black-Right-Pointing-Pointer We present the e-waste collection systems used in Europe and in the US. Black-Right-Pointing-Pointer We present e-waste collection systems used in Asia and Latin America. Black-Right-Pointing-Pointer E-waste management between developed and developing countries is very different. Black-Right-Pointing-Pointer We made a comparison of the world situation to the current Brazilian reality. - Abstract: Recycling and the related issue of sustainable development are increasing in importance around the world. In Brazil, the new National Policy on Solid Wastes has prompted discussion on the future of electronic waste (e-waste). Over the last 10 years, different e-waste collection systems and recycling processes have been applied globally. This paper presents the systems used in different countries and compares the world situation to the current Brazilian reality. To establish a recycling process, it is necessary to organize efficient collection management. The main difficulty associated with the implementation of e-waste recycling processes in Brazil is the collection system, as its efficiency depends not only on the education and cooperation of the people but also on cooperation among industrial waste generators, distributors and the government. Over half a million waste pickers have been reported in Brazil and they are responsible for the success of metal scrap collection in the country. The country also has close to 2400 companies and cooperatives involved in recycling and scrap trading. On the other hand, the collection and recycling of e-waste is still incipient because e-wastes are not seen as valuable in the informal sector. The Brazilian challenge is therefore to organize a system of e-waste management including the informal sector without neglecting environmentally sound management principles.

  7. MicroED data collection and processing

    SciTech Connect (OSTI)

    Hattne, Johan; Reyes, Francis E.; Nannenga, Brent L.; Shi, Dan; Cruz, M. Jason de la; Leslie, Andrew G. W.; Gonen, Tamir

    2015-07-01

    The collection and processing of MicroED data are presented. MicroED, a method at the intersection of X-ray crystallography and electron cryo-microscopy, has rapidly progressed by exploiting advances in both fields and has already been successfully employed to determine the atomic structures of several proteins from sub-micron-sized, three-dimensional crystals. A major limiting factor in X-ray crystallography is the requirement for large and well ordered crystals. By permitting electron diffraction patterns to be collected from much smaller crystals, or even single well ordered domains of large crystals composed of several small mosaic blocks, MicroED has the potential to overcome the limiting size requirement and enable structural studies on difficult-to-crystallize samples. This communication details the steps for sample preparation, data collection and reduction necessary to obtain refined, high-resolution, three-dimensional models by MicroED, and presents some of its unique challenges.

  8. Collective excitation spectra of transitional even nuclei

    SciTech Connect (OSTI)

    Quentin, P. Paris-11 Univ., 91 - Orsay . Centre de Spectrometrie Nucleaire et de Spectrometrie de Masse); Deloncle, I.; Libert, J. . Centre de Spectrometrie Nucleaire et de Spectrometrie de Masse); Sauvage, J. . Inst. de Physique Nucleaire)

    1990-11-06

    This talk is dealing with the nuclear low energy collective motion as described in the context of microscopic versions of the Bohr Hamiltonian. Two different ways of building microscopically Bohr collective Hamiltonians will be sketched; one within the framework of the Generator Coordinate Method, the other using the Adiabatic Time-Dependent Hartree-Fock-Boholyubov approximation. A sample of recent results will be presented which pertains to the description of transitional even nuclei and to the newly revisited phenomenon of superdeformation at low spin.

  9. Digestion of frozen/thawed food waste in the hybrid anaerobic solid-liquid system

    SciTech Connect (OSTI)

    Stabnikova, O. Liu, X.Y.; Wang, J.Y.

    2008-07-01

    The hybrid anaerobic solid-liquid (HASL) system, which is a modified two-phase anaerobic digester, is to be used in an industrial scale operation to minimize disposal of food waste at incineration plants in Singapore. The aim of the present research was to evaluate freezing/thawing of food waste as a pre-treatment for its anaerobic digestion in the HASL system. The hydrolytic and fermentation processes in the acidogenic reactor were enhanced when food waste was frozen for 24 h at -20 deg. C and then thawed for 12 h at 25 deg. C (experiment) in comparison with fresh food waste (control). The highest dissolved COD concentrations in the leachate from the acidogenic reactors were 16.9 g/l on day 3 in the control and 18.9 g/l on day 1 in the experiment. The highest VFA concentrations in the leachate from the acidogenic reactors were 11.7 g/l on day 3 in the control and 17.0 g/l on day 1 in the experiment. The same volume of methane was produced during 12 days in the control and 7 days in the experiment. It gave the opportunity to diminish operational time of batch process by 42%. The effect of freezing/thawing of food waste as pre-treatment for its anaerobic digestion in the HASL system was comparable with that of thermal pre-treatment of food waste at 150 deg. C for 1 h. However, estimation of energy required either to heat the suspended food waste to 150 deg. C or to freeze the same quantity of food waste to -20 deg. C showed that freezing pre-treatment consumes about 3 times less energy than thermal pre-treatment.

  10. Metal current collect protected by oxide film

    DOE Patents [OSTI]

    Jacobson, Craig P. (Lafayette, CA); Visco, Steven J. (Berkeley, CA); DeJonghe, Lutgard C. (Lafayette, CA)

    2004-05-25

    Provided are low-cost, mechanically strong, highly electronically conductive current collects and associated structures for solid-state electrochemical devices, techniques for forming these structures, and devices incorporating the structures. The invention provides solid state electrochemical devices having as current interconnects a ferritic steel felt or screen coated with a protective oxide film.

  11. 2004 Savannah River Cooling Tower Collection (U)

    SciTech Connect (OSTI)

    Garrett, Alfred; Parker, Matthew J.; Villa-Aleman, E.

    2005-05-01

    The Savannah River National Laboratory (SRNL) collected ground truth in and around the Savannah River Site (SRS) F-Area cooling tower during the spring and summer of 2004. The ground truth data consisted of air temperatures and humidity inside and around the cooling tower, wind speed and direction, cooling water temperatures entering; inside adn leaving the cooling tower, cooling tower fan exhaust velocities and thermal images taken from helicopters. The F-Area cooling tower had six cells, some of which were operated with fans off during long periods of the collection. The operating status (fan on or off) for each of the six cells was derived from operations logbooks and added to the collection database. SRNL collected the F-Area cooling tower data to produce a database suitable for validation of a cooling tower model used by one of SRNL's customer agencies. SRNL considers the data to be accurate enough for use in a model validation effort. Also, the thermal images of the cooling tower decks and throats combined with the temperature measurements inside the tower provide valuable information about the appearance of cooling towers as a function of fan operating status and time of day.

  12. ACRF Data Collection and Processing Infrastructure

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    6 ACRF Data Collection and Processing Infrastructure December 2004 M.C. Macduff, Pacific Northwest National Laboratory R.C. Eagan Argonne National Laboratory Work supported by the U.S. Department of Energy, Office of Science, Office of Biological and Environmental Research M.C. Macduff et al., November 2004, ARM TR-046 Contents 1. Introduction ............................................................................................................................................ 1 2. Global

  13. Quantum chaos in the nuclear collective model. II. Peres lattices

    SciTech Connect (OSTI)

    Stransky, Pavel; Hruska, Petr; Cejnar, Pavel [Institute of Particle and Nuclear Physics, Faculty of Mathematics and Physics, Charles University, V Holesovickach 2, 180 00 Prague (Czech Republic)

    2009-06-15

    This is a continuation of our paper [Phys. Rev. E 79, 046202 (2009)] devoted to signatures of quantum chaos in the geometric collective model of atomic nuclei. We apply the method by Peres to study ordered and disordered patterns in quantum spectra drawn as lattices in the plane of energy vs average of a chosen observable. Good qualitative agreement with standard measures of chaos is manifested. The method provides an efficient tool for studying structural changes in eigenstates across quantum spectra of general systems.

  14. H2 Refuel H-Prize Technical Data Collection Requirements

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    H2 Refuel H-Prize Technical Data Collection Requirements Katie Randolph, PhD Sarah Studer, PhD U.S. Department of Energy Fuel Cell Technologies Office 2 Question and Answer * Please type your question into the question box hydrogenandfuelcells.energy.gov Fuel Cell Technologies Office | 3 5/15/2015 2014-2016 H-Prize competition Challenging America's innovators to develop on-site systems to generate and dispense hydrogen to fuel vehicles at homes, community centers or small businesses. The Best

  15. A garbage collection algorithm for shared memory parallel processors

    SciTech Connect (OSTI)

    Crammond, J. )

    1988-12-01

    This paper describes a technique for adapting the Morris sliding garbage collection algorithm to execute on parallel machines with shared memory. The algorithm is described within the framework of an implementation of the parallel logic language Parlog. However, the algorithm is a general one and can easily be adapted to parallel Prolog systems and to other languages. The performance of the algorithm executing a few simple Parlog benchmarks is analyzed. Finally, it is shown how the technique for parallelizing the sequential algorithm can be adapted for a semi-space copying algorithm.

  16. Contacts for Information Collection Management | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Information Collection Management Contacts for Information Collection Management Information Collection Program, and Information Quality Guidelines Christina Rouleau, IM-23 Records Management Division Office of the CIO US Department of Energy 301-903-6227 Christina.Rouleau

  17. Value Stream Mapping: Foam Collection and Processing.

    SciTech Connect (OSTI)

    Sorensen, Christian

    2015-07-01

    The effort to collect and process foam for the purpose of recycling performed by the Material Sustainability and Pollution Prevention (MSP2) team at Sandia National Laboratories is an incredible one, but in order to make it run more efficiently it needed some tweaking. This project started in June of 2015. We used the Value Stream Mapping process to allow us to look at the current state of the foam collection and processing operation. We then thought of all the possible ways the process could be improved. Soon after that we discussed which of the "dreams" were feasible. And finally, we assigned action items to members of the team so as to ensure that the improvements actually occur. These improvements will then, due to varying factors, continue to occur over the next couple years.

  18. Water Data Collection in the 2007 CBECS

    Gasoline and Diesel Fuel Update (EIA)

    Water Data Collection in the 2007 CBECS CBECS 2007 - Release date: August 28, 2012 Did you know? Select water data results are described in the accompanying report, Energy Characteristics and Energy Consumed in Large Hospital Buildings in the United States in 2007 and tabulated in 2007 CBECS Large Hospital Building List of Tables. The 2007 round of the Commercial Buildings Energy Consumption Survey (CBECS) was the first time in the 30 year CBECS history that questions about water consumption

  19. Federal Register Notice: Proposed Agency Information Collection

    Broader source: Energy.gov [DOE]

    Federal Register Notice on the DOEs invitation for public comment on its request to the Office of Management and Budget (OMB) to extend for three years the Information Collection Request Title: OE Recovery Act Financial Assistance Grants, OMB Control No. 19105149 that DOE is developing for submission to OMB pursuant to the Paperwork Reduction Act of 1995. Comments due on or before November 7, 2011.

  20. Federal Register Notice: Proposed Agency Information Collection

    Broader source: Energy.gov [DOE]

    Federal Register Notice on the DOEs invitation for public comment on its intent to request the Office of Management and Budget (OMB) to extend for four years the Information Collection Request Title: OE Recovery Act Financial Assistance Grants, OMB Control No. 19105149 that DOE is developing for submission to OMB pursuant to the Paperwork Reduction Act of 1995. Comments due on or before October 11, 2011.

  1. Biomass Engineering: Harvest, Collection, and Storage

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    1.2.1.1 Biomass Engineering: Harvest, Collection, and Storage March 25, 2015 William A Smith, Ian J Bonner, & Lynn M Wendt Idaho National Laboratory Biomass and Bioenergy This presentation does not contain any proprietary, confidential, or otherwise restricted information DOE Bioenergy Technologies Office 2015 Project Peer Review Feedstock Supply and Logistics 2 | Bioenergy Technologies Office Goal Statement * Objective - Identify and develop solutions to feedstock supply and storage

  2. Aluminum low temperature smelting cell metal collection

    DOE Patents [OSTI]

    Beck, Theodore R. (Seattle, WA); Brown, Craig W. (Seattle, WA)

    2002-07-16

    A method of producing aluminum in an electrolytic cell containing alumina dissolved in an electrolyte. The method comprises the steps of providing a molten salt electrolyte in an electrolytic cell having an anodic liner for containing the electrolyte, the liner having an anodic bottom and walls including at least one end wall extending upwardly from the anodic bottom, the anodic liner being substantially inert with respect to the molten electrolyte. A plurality of non-consumable anodes is provided and disposed vertically in the electrolyte. A plurality of cathodes is disposed vertically in the electrolyte in alternating relationship with the anodes. The anodes are electrically connected to the anodic liner. An electric current is passed through the anodic liner to the anodes, through the electrolyte to the cathodes, and aluminum is deposited on said cathodes. Oxygen bubbles are generated at the anodes and the anodic liner, the bubbles stirring the electrolyte. Molten aluminum is collected from the cathodes into a tubular member positioned underneath the cathodes. The tubular member is in liquid communication with each cathode to collect the molten aluminum therefrom while excluding electrolyte. Molten aluminum is delivered through the tubular member to a molten aluminum reservoir located substantially opposite the anodes and cathodes. The molten aluminum is collected from the cathodes and delivered to the reservoir while avoiding contact of the molten aluminum with the anodic bottom.

  3. Optical selection and collection of DNA fragments

    DOE Patents [OSTI]

    Roslaniec, Mary C. (Los Alamos, NM); Martin, John C. (Los Alamos, NM); Jett, James H. (Los Alamos, NM); Cram, L. Scott (Los Alamos, NM)

    1998-01-01

    Optical selection and collection of DNA fragments. The present invention includes the optical selection and collection of large (>.mu.g) quantities of clonable, chromosome-specific DNA from a sample of chromosomes. Chromosome selection is based on selective, irreversible photoinactivation of unwanted chromosomal DNA. Although more general procedures may be envisioned, the invention is demonstrated by processing chromosomes in a conventional flow cytometry apparatus, but where no droplets are generated. All chromosomes in the sample are first stained with at least one fluorescent analytic dye and bonded to a photochemically active species which can render chromosomal DNA unclonable if activated. After passing through analyzing light beam(s), unwanted chromosomes are irradiated using light which is absorbed by the photochemically active species, thereby causing photoinactivation. As desired chromosomes pass this photoinactivation point, the inactivating light source is deflected by an optical modulator; hence, desired chromosomes are not photoinactivated and remain clonable. The selection and photoinactivation processes take place on a microsecond timescale. By eliminating droplet formation, chromosome selection rates 50 times greater than those possible with conventional chromosome sorters may be obtained. Thus, usable quantities of clonable DNA from any source thereof may be collected.

  4. Energy Conservation Program: Data Collection and Comparison with...

    Energy Savers [EERE]

    Energy Conservation Program: Data Collection and Comparison with Forecasted Unit Sales for Five Lamp Types, Notice of Data Availability Energy Conservation Program: Data Collection ...

  5. DOE Technical Standards Archived Collection | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    DOE Technical Standards Program DOE Technical Standards Archived Collection DOE Technical Standards Archived Collection Document ID Filter Document ID sort descending Title Date ...

  6. Truck Duty Cycle and Performance Data Collection and Analysis...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    More Documents & Publications Heavy Duty & Medium Duty Drive Cycle Data Collection for Modeling Expansion Truck Duty Cycle and Performance Data Collection and Analysis Program 2010 ...

  7. Truck Duty Cycle and Performance Data Collection and Analysis...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    More Documents & Publications Truck Duty Cycle and Performance Data Collection and Analysis Program Heavy Duty & Medium Duty Drive Cycle Data Collection for Modeling Expansion ...

  8. Heavy Duty & Medium Duty Drive Cycle Data Collection for Modeling...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Heavy Duty & Medium Duty Drive Cycle Data Collection for Modeling Expansion Heavy Duty & Medium Duty Drive Cycle Data Collection for Modeling Expansion 2009 DOE Hydrogen Program ...

  9. Heat Flow Database Expansion for NGDS Data Development, Collection...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Heat Flow Database Expansion for NGDS Data Development, Collection and Maintenance (SMU) Heat Flow Database Expansion for NGDS Data Development, Collection and Maintenance (SMU) ...

  10. Data Collection for Improved Cold Temperature Thermal Modeling...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Modeling and Strategy Development Data Collection for Improved Cold Temperature Thermal ... More Documents & Publications Data Collection for Improved Cold Temperature Thermal ...

  11. City of Fort Collins Comment on Information Collection Extension...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    City of Fort Collins Comment on Information Collection Extension, October 2011 City of Fort Collins Comment on Information Collection Extension, October 2011 The City of Fort...

  12. Understanding Collection-Related Losses in Organic Solar Cells...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Understanding Collection-Related Losses in Organic Solar Cells Home > Research > ANSER Research Highlights > Understanding Collection-Related Losses in Organic Solar Cells...

  13. ORISE: Worker Health Studies - Radiation Exposure Data Collection

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Collection ORISE manages large, occupation radition exposure databases for both DOE and NRC Radiation Exposure Data Collection The Oak Ridge Institute for Science and Education...

  14. Collective Dissipation from Saddle to Scission in a Microscopic...

    Office of Scientific and Technical Information (OSTI)

    Collective Dissipation from Saddle to Scission in a Microscopic Approach Citation Details In-Document Search Title: Collective Dissipation from Saddle to Scission in a Microscopic ...

  15. Scalable Run Time Data Collection Analysis and Visualization...

    Office of Scientific and Technical Information (OSTI)

    Scalable Run Time Data Collection Analysis and Visualization (Presentation). Citation Details In-Document Search Title: Scalable Run Time Data Collection Analysis and Visualization...

  16. OVIS: Scalable Run Time Data Collection Analysis and Visualization...

    Office of Scientific and Technical Information (OSTI)

    OVIS: Scalable Run Time Data Collection Analysis and Visualization (Abstract). Citation Details In-Document Search Title: OVIS: Scalable Run Time Data Collection Analysis and...

  17. User Statistics Collection Practices Archives | U.S. DOE Office...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Policies and Processes User Statistics Collection Practices User Statistics Collection Practices Archives User Facilities User Facilities Home User Facilities at a Glance...

  18. Evidence for collective multiparticle correlations in p–Pb collisions

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Khachatryan, V.; Sirunyan, A. M.; Tumasyan, A.; Adam, W.; Bergauer, T.; Dragicevic, M.; Erö, J.; Friedl, M.; Frühwirth, R.; Ghete, V. M.; et al

    2015-06-29

    The second-order azimuthal anisotropy Fourier harmonics, v₂, are obtained in p−Pb and PbPb collisions over a wide pseudorapidity (η) range based on correlations among six or more charged particles. The p-Pb data, corresponding to an integrated luminosity of 35  nb⁻¹, were collected during the 2013 LHC p-Pb run at a nucleon-nucleon center-of-mass energy of 5.02  TeV by the CMS experiment. A sample of semiperipheral PbPb collision data at √s = 2.76  TeV, corresponding to an integrated luminosity of 2.5  μb⁻¹ and covering a similar range of particle multiplicities as the p−Pb data, is also analyzed for comparison. The six- and eight-particle cumulant and themore » Lee-Yang zeros methods are used to extract the v₂ coefficients, extending previous studies of two- and four-particle correlations. For both the p−Pb and PbPb systems, the v₂ values obtained with correlations among more than four particles are consistent with previously published four-particle results. These data support the interpretation of a collective origin for the previously observed long-range (large Δη) correlations in both systems. The ratios of v2 values corresponding to correlations including different numbers of particles are compared to theoretical predictions that assume a hydrodynamic behavior of a p−Pb system dominated by fluctuations in the positions of participant nucleons. These results provide new insights into the multiparticle dynamics of collision systems with a very small overlapping region.« less

  19. Vacuum Attachment for Collection of Lithium Powder ---- Inventor(s) Hans

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Schneider and Stephan Jurczynski | Princeton Plasma Physics Lab Vacuum Attachment for Collection of Lithium Powder ---- Inventor(s) Hans Schneider and Stephan Jurczynski The Vacuum Attachment is part of an integrated system designed to collect Lithium (Li) Power for storage in mineral oil or to passivate it in Vinegar or Chilled Water. Major components are: Mister, Li Trap, Oil Trap or Combustion Chamber and Ash rated Shop Vacuum. The Mister provides a fine coating of mineral oil, vinegar or

  20. Quadrupole collective dynamics from energy density functionals: Collective Hamiltonian and the interacting boson model

    SciTech Connect (OSTI)

    Nomura, K.; Vretenar, D.; Niksic, T.; Otsuka, T.; Shimizu, N.

    2011-07-15

    Microscopic energy density functionals have become a standard tool for nuclear structure calculations, providing an accurate global description of nuclear ground states and collective excitations. For spectroscopic applications, this framework has to be extended to account for collective correlations related to restoration of symmetries broken by the static mean field, and for fluctuations of collective variables. In this paper, we compare two approaches to five-dimensional quadrupole dynamics: the collective Hamiltonian for quadrupole vibrations and rotations and the interacting boson model (IBM). The two models are compared in a study of the evolution of nonaxial shapes in Pt isotopes. Starting from the binding energy surfaces of {sup 192,194,196}Pt, calculated with a microscopic energy density functional, we analyze the resulting low-energy collective spectra obtained from the collective Hamiltonian, and the corresponding IBM Hamiltonian. The calculated excitation spectra and transition probabilities for the ground-state bands and the {gamma}-vibration bands are compared to the corresponding sequences of experimental states.

  1. Light Collection in Liquid Noble Gases

    SciTech Connect (OSTI)

    McKinsey, Dan [Yale University

    2013-05-29

    Liquid noble gases are increasingly used as active detector materials in particle and nuclear physics. Applications include calorimeters and neutrino oscillation experiments as well as searches for neutrinoless double beta decay, direct dark matter, muon electron conversion, and the neutron electric dipole moment. One of the great advantages of liquid noble gases is their copious production of ultraviolet scintillation light, which contains information about event energy and particle type. I will review the scintillation properties of the various liquid noble gases and the means used to collect their scintillation light, including recent advances in photomultiplier technology and wavelength shifters.

  2. 'Bradbury Science Museum Collections Inventory Photos Disc #4

    SciTech Connect (OSTI)

    Strohmeyer, Wendy J.

    2015-11-16

    The photos on Bradbury Science Museum Collections Inventory Photos Disc #4 is another in an ongoing effort to catalog all artifacts held by the Museum. Photos will be used as part of the condition report for the artifact, and will become part of the collection record in the collections database for that artifact. The collections database will be publically searchable on the Museum website.

  3. Benchmarking Outreach and Data Collection Techniques for External Portfolios

    Broader source: Energy.gov [DOE]

    This presentation contains information on Benchmarking Outreach and Data Collection Techniques for External Portfolios.

  4. Automated collection and processing of environmental samples

    DOE Patents [OSTI]

    Troyer, Gary L. (Richland, WA); McNeece, Susan G. (Richland, WA); Brayton, Darryl D. (Richland, WA); Panesar, Amardip K. (Kennewick, WA)

    1997-01-01

    For monitoring an environmental parameter such as the level of nuclear radiation, at distributed sites, bar coded sample collectors are deployed and their codes are read using a portable data entry unit that also records the time of deployment. The time and collector identity are cross referenced in memory in the portable unit. Similarly, when later recovering the collector for testing, the code is again read and the time of collection is stored as indexed to the sample collector, or to a further bar code, for example as provided on a container for the sample. The identity of the operator can also be encoded and stored. After deploying and/or recovering the sample collectors, the data is transmitted to a base processor. The samples are tested, preferably using a test unit coupled to the base processor, and again the time is recorded. The base processor computes the level of radiation at the site during exposure of the sample collector, using the detected radiation level of the sample, the delay between recovery and testing, the duration of exposure and the half life of the isotopes collected. In one embodiment, an identity code and a site code are optically read by an image grabber coupled to the portable data entry unit.

  5. Information Collection Requests/Paper Reduction Act | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Information Collection Requests/Paper Reduction Act Information Collection Requests/Paper Reduction Act Training Presentation on the on Information Collection and the Paper Reduction Act PDF icon Information Collection Requests/Paper Reduction Act More Documents & Publications Step by Step Instruction - ICR - FINAL Notice of Office of Management and Budget Action to Approve with Change the Information Collection Request (ICR) for an Extension of the ICR for OE Recovery Act Financial

  6. Early detection and evaluation of waste through sensorized containers for a collection monitoring application

    SciTech Connect (OSTI)

    Rovetta, Alberto; Fan Xiumin; Vicentini, Federico; Zhu Minghua; Giusti, Alessandro; He Qichang

    2009-12-15

    The present study describes a novel application for use in the monitoring of municipal solid waste, based on distributed sensor technology and geographical information systems. Original field testing and evaluation of the application were carried out in Pudong, Shanghai (PR China). The local waste management system in Pudong features particular requirements related to the rapidly increasing rate of waste production. In view of the fact that collected waste is currently deployed to landfills or to incineration plants within the context investigated, the key aspects to be taken into account in waste collection procedures include monitoring of the overall amount of waste produced, quantitative measurement of the waste present at each collection point and identification of classes of material present in the collected waste. The case study described herein focuses particularly on the above mentioned aspects, proposing the implementation of a network of sensorized waste containers linked to a data management system. Containers used were equipped with a set of sensors mounted onto standard waste bins. The design, implementation and validation procedures applied are subsequently described. The main aim to be achieved by data collection and evaluation was to provide for feasibility analysis of the final device. Data pertaining to the content of waste containers, sampled and processed by means of devices validated on two purpose-designed prototypes, were therefore uploaded to a central monitoring server using GPRS connection. The data monitoring and management modules are integrated into an existing application used by local municipal authorities. A field test campaign was performed in the Pudong area. The system was evaluated in terms of real data flow from the network nodes (containers) as well as in terms of optimization functions, such as collection vehicle routing and scheduling. The most important outcomes obtained were related to calculations of waste weight and volume. The latter data were subsequently used as parameters for the routing optimization of collection trucks and material density evaluation.

  7. Diffractometer data collecting method and apparatus

    DOE Patents [OSTI]

    Steinmeyer, P.A.

    1991-04-16

    Diffractometer data is collected without the use of a movable receiver. A scanning device, positioned in the diffractometer between a sample and detector, varies the amount of the beam diffracted from the sample that is received by the detector in such a manner that the beam is detected in an integrated form. In one embodiment, a variable diameter beam stop is used which comprises a drop of mercury captured between a pair of spaced sheets and disposed in the path of the diffracted beam. By varying the spacing between the sheets, the diameter of the mercury drop is varied. In another embodiment, an adjustable iris diaphragm is positioned in the path of the diffracted beam and the iris opening is adjusted to control the amount of the beam reaching the detector. 5 figures.

  8. State protection under collective damping and diffusion

    SciTech Connect (OSTI)

    Ponte, M. A. de [Instituto de Fisica de Sao Carlos, Universidade de Sao Paulo, Caixa Postal 369, 13560-590 Sao Carlos, SP (Brazil); Departamento de Fisica, Universidade Regional do Cariri, 63010-970 Juazeiro do Norte, CE (Brazil); Mizrahi, S. S. [Departamento de Fisica, Universidade Federal de Sao Carlos, 13565-905 Sao Carlos, SP (Brazil); Moussa, M. H. Y. [Instituto de Fisica de Sao Carlos, Universidade de Sao Paulo, Caixa Postal 369, 13560-590 Sao Carlos, SP (Brazil)

    2011-07-15

    In this paper we provide a recipe for state protection in a network of oscillators under collective damping and diffusion. Our strategy is to manipulate the network topology, i.e., the way the oscillators are coupled together, the strength of their couplings, and their natural frequencies, in order to create a relaxation-diffusion-free channel. This protected channel defines a decoherence-free subspace (DFS) for nonzero-temperature reservoirs. Our development also furnishes an alternative approach to build up DFSs that offers two advantages over the conventional method: it enables the derivation of all the network-protected states at once, and also reveals, through the network normal modes, the mechanism behind the emergence of these protected domains.

  9. Device for collecting emissions from kerosene heaters

    SciTech Connect (OSTI)

    Gilloti, N.J.

    1984-09-04

    An apparatus for both improving the heat distribution throughout a room from a portable kerosene heater and for collecting undesirable emissions resulting from the burning of the kerosene, includes a base adapted to be mounted on the top of the heater, the base supporting a vertically extending shaft on which is mounted a heat-driven fan formed of either paper or metal, and a disposable disk mounted a spaced distance above the fan on the same shaft, the disk serving as a collector for the undesirable emissions. When the device is placed on an operating kerosene heater, the rising hot air and gases from the heater cause the fan to rotate, which in turn causes emissions from the burning fuel to move upwardly in a more or less cylindrical path. As the products of combustion move upwardly, certain emissions therein such as soot, oily vapors, etc. deposit or condense onto the surface of the spinner and disposable disk.

  10. Experimental nuclear reaction data collection EXFOR

    SciTech Connect (OSTI)

    Semkova, V.; Otuka, N.; Simakov, S. P.; Zerkin, V.

    2011-07-01

    The International Network of Nuclear Reaction Data Centres (NRDC) constitutes a worldwide cooperation of 14 nuclear data centres. The main activity of the NRDC Network is collection and compilation of experimental nuclear reaction cross section data and the related bibliographic information in the EXFOR and CINDA databases as well as dissemination of nuclear reaction data and associated documentation to users. The database contains information and numerical data from more than about 19000 experiments consisting of more than 140000 datasets. EXFOR is kept up to date by constantly adding newly published experimental information. Tools developed for data dissemination utilise modern database technologies with fast online capabilities over the Internet. Users are provided with sophisticated search options, a user-friendly retrieval interface for downloading data in different formats, and additional output options such as improved data plotting capabilities. The present status of the EXFOR database will be presented together with the latest development for data access and retrieval. (authors)

  11. Apparatus and method for collection and concentration of respirable particles into a small fluid volume

    DOE Patents [OSTI]

    Simon, Jonathan N. (San Leandro, CA); Brown, Steve B. (Livermore, CA)

    2002-01-01

    An apparatus and method for the collection of respirable particles and concentration of such particles into a small fluid volume. The apparatus captures and concentrates small (1-10 .mu.m) respirable particles into a sub-millileter volume of fluid. The method involves a two step operation, collection and concentration: wherein collection of particles is by a wetted surface having small vertical slits that act as capillary channels; and concentration is carried out by transfer of the collected particles to a small volume (sub-milliliter) container by centrifugal force whereby the particles are forced through the vertical slits and contact a non-wetted wall surface, and are deflected to the bottom where they are contained for analysis, such as a portable flow cytometer or a portable PCR DNA analysis system.

  12. Effects of aqueous-soluble organic compounds on the removal of selected radionuclides from high-level waste part I: Distribution of Sr, Cs, and Tc onto 18 absorbers from an irradiated, organic-containing leachate simulant for Hanford Tank 101-SY

    SciTech Connect (OSTI)

    Marsh, S.F.; Svitra, Z.V.; Bowen, S.M.

    1995-01-01

    Many of the radioactive waste storage tanks at U.S. Department of Energy facilities contain organic compounds that have been degraded by radiolysis and chemical reactions. In this investigation, we measured the effect of some aqueous-soluble organic compounds on the sorption of strontium, cesium, and technetium onto 18 absorbers that offer high sorption of strontium from organic-free solutions. For our test solution we used a leachate from a simulated slurry for Hanford Tank 101-SY that initially contained ethylenediaminetetraacetic acid (EDTA) and then was gamma-irradiated to 34 Mrads. We measured distribution coefficients (Kds) for each element/absorber combination for dynamic contact periods of 30 min, 2 h, and 6 h to obtain information about sorption kinetics. To facilitate comparisons, we include Kd values for these same element/absorber combinations from three organic-free simulant solutions. The Kd values for strontium sorption from the simulant that contained the degraded organics usually decreased by large factors, whereas the Kd values for cesium and technetium sorption were relatively unaffected.

  13. Smisc - A collection of miscellaneous functions

    Energy Science and Technology Software Center (OSTI)

    2015-08-31

    A collection of functions for statistical computing and data manipulation. These include routines for rapidly aggregating heterogeneous matrices, manipulating file names, loading R objects, sourcing multiple R files, formatting datetimes, multi-core parallel computing, stream editing, specialized plotting, etc. • Smisc-package A collection of miscellaneous functions allMissing Identifies missing rows or columns in a data frame or matrix as.numericSilent Silent wrapper for coercing a vector to numeric comboList Produces all possible combinations of a set ofmore » linear model predictors cumMax Computes the maximum of the vector up to the current index cumsumNA Computes the cummulative sum of a vector without propogating NAs d2binom Probability functions for the sum of two independent binomials dataIn A flexible way to import data into R. dbb The Beta-Binomial Distribution df2list Row-wise conversion of a data frame to a list dfplapply Parallelized single row processing of a data frame dframeEquiv Examines the equivalence of two dataframes or matrices dkbinom Probability functions for the sum of k independent binomials factor2character Converts all factor variables in a dataframe to character variables findDepMat Identify linearly dependent rows or columns in a matrix formatDT Converts date or datetime strings into alternate formats getExtension Filename manipulations: remove the extension or path, extract the extension or path getPath Filename manipulations: remove the extension or path, extract the extension or path grabLast Filename manipulations: remove the extension or path, extract the extension or path ifelse1 Non-vectorized version of ifelse integ Simple numerical integration routine interactionPlot Two-way Interaction Plot with Error Bar linearMap Linear mapping of a numerical vector or scalar list2df Convert a list to a data frame loadObject Loads and returns the object(s) in an ".Rdata" file more Display the contents of a file to the R terminal movAvg2 Calculate the moving average using a 2-sided window openDevice Opens a graphics device based on the filename extension p2binom Probability functions for the sum of two independent binomials padZero Pad a vector of numbers with zeros parseJob Parses a collection of elements into (almost) equal sized groups pbb The Beta-Binomial Distribution pcbinom A continuous version of the binomial cdf pkbinom Probability functions for the sum of k independent binomials plapply Simple parallelization of lapply plotFun Plot one or more functions on a single plot PowerData An example of power data pvar Prints the name and value of one or more objects qbb The Beta-Binomial Distribution rbb And numerous others (space limits reporting).« less

  14. Parallel Radioisotope Collection and Analysis in Response to the Fukushima Release

    SciTech Connect (OSTI)

    Woods, Vincent T.; Bowyer, Ted W.; Biegalski, S.; Greenwood, Lawrence R.; Haas, Derek A.; Hayes, James C.; Lepel, Elwood A.; Miley, Harry S.; Morris, Scott J.

    2013-05-01

    Two independent air samplers were operated at Pacific Northwest National Laboratory in parallel during the collection of samples from the Fukushima reactor releases. One system is an automated aerosol collection and analysis unit, while the other was a manual sampler of higher daily air volume. The samples collected each day showed excellent correlation in radionuclide activity, although some variations were seen. These variations illustrate the reproducibility of the air sample radionuclide measurements made by the Comprehensive Nuclear-Test-Ban Treaty International Monitoring System (IMS) and show a simple way to acquire useful parallel samples for scientific purposes. In particular, a party wishing to have a “copy” of a sample acquired by the verification regime of the treaty could employ this method and have results similar to the IMS station at low cost and even higher sensitivity.

  15. Low-energy collective modes of deformed superfluid nuclei within...

    Office of Scientific and Technical Information (OSTI)

    Low-energy collective modes of deformed superfluid nuclei within the finite-amplitude method Citation Details In-Document Search Title: Low-energy collective modes of deformed ...

  16. Understanding Collection-Related Losses in Organic Solar Cells | ANSER

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Center | Argonne-Northwestern National Laboratory Understanding Collection-Related Losses in Organic Solar Cells Home > Research > ANSER Research Highlights > Understanding Collection-Related Losses in Organic Solar Cells

  17. How to Collect and Examine your Building Data

    SciTech Connect (OSTI)

    2009-01-18

    This fact sheet provides advice on how to collect and analyze data when conducting an energy audit on a building.

  18. Benchmarking Outreach and Data Collection Techniques for External Portfolios

    Broader source: Energy.gov [DOE]

    This document contains the transcript for the Benchmarking Outreach and Data Collection Techniques webinar, held on April 25, 2013.

  19. Data Collection & Analysis Software | Stanford Synchrotron Radiation

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Lightsource Collection & Analysis Software Techniques Data Collection Packages Data Analysis Packages Macromolecular Crystallography See http://smb.slac.stanford.edu/facilities/ See http://smb.slac.stanford.edu/facilities/ Materials Scattering SPEC Super X-ray Absorption Spectroscopy XAS Collect uses an X Window-based graphical user interface. It is designed to allow quick and easy XAS experimental setup and data collection, and to make optimal use of available beam time. It has many

  20. Commercial Building Energy Asset Score 2013 Pilot Data Collection Form |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Pilot Data Collection Form Commercial Building Energy Asset Score 2013 Pilot Data Collection Form This form is intended to facilitate your data collection. The Energy Asset Scoring Tool uses the "block" concept to simplify your building geometry. Most buildings can be scored as one block PDF icon Commercial Building Energy Asset Score 2013 Pilot Data Collection Form More Documents & Publications Commercial Building Energy Asset Score Sample Report Chapter

  1. Town of Danvers Comment on Information Collection Extension | Department of

    Energy Savers [EERE]

    Energy Town of Danvers Comment on Information Collection Extension Town of Danvers Comment on Information Collection Extension The Town of Danvers provided comments to the Department of Energy's notice of intent to seek approval of an extension of Information Collection 1910-5149 for Recovery Act Smart Grid Investment Grant reporting for four years, which was published in the Federal Register August 10, 2011, Vol. 76, No. 154, page 49460. Danvers finds the current collection period

  2. OMB 1910-5122, Human Reliability Program- Description of Collections

    Broader source: Energy.gov [DOE]

    Office of Environment, Health, Safety and Security: OMB 1910-5122, Human Reliability Program - Description of Collections

  3. Home Energy Score Data Collection Form | Department of Energy

    Energy Savers [EERE]

    Data Collection Form Home Energy Score Data Collection Form Input sheet for qualified assessors to collect data for input into the Home Energy Scoring Tool for evaluation. PDF icon Data Collection Sheet More Documents & Publications Home Energy Score Sample Report Building America Efficient Solutions for Existing Homes Case Study: Deep Energy Retrofit of 1910 House, Portland, Oregon Building America Whole-House Solutions for New Homes: New Traditions, Vancouver, Washington

  4. Controlling Data Collection to Support SAR Image Rotation

    DOE Patents [OSTI]

    Doerry, Armin W. (Albuquerque, NM); Cordaro, J. Thomas (Albuquerque, NM); Burns, Bryan L. (Tijeras, NM)

    2008-10-14

    A desired rotation of a synthetic aperture radar (SAR) image can be facilitated by adjusting a SAR data collection operation based on the desired rotation. The SAR data collected by the adjusted SAR data collection operation can be efficiently exploited to form therefrom a SAR image having the desired rotational orientation.

  5. Strategies for Collecting Household Energy Data | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Collecting Household Energy Data Strategies for Collecting Household Energy Data Better Buildings Neighborhood Program Data and Evaluation Peer Exchange Call: Strategies for Collecting Household Energy Data, Call Slides and Discussion Summary, July 19, 2012. PDF icon Call Slides and Discussion Summary More Documents & Publications Homeowner and Contractor Surveys Mastermind: Jim Mikel, Spirit Foundation Generating Energy Efficiency Project Leads and Allocating Leads to Contractors

  6. Data Collection and Normalization for the Development of Cost Estimating Relationships

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1997-03-28

    Cost estimating relationships or parametric equations are mathematical statements that indicate that the cost is proportional to a physical commodity. Parametric estimating requires that the statistical analysis be performed on data points to correlate the cost drivers and other system parameters. This chapter discusses considerations for data collection and normalization.

  7. DOE Science Showcase - Earth System Models | OSTI, US Dept of...

    Office of Scientific and Technical Information (OSTI)

    Earth System Models Research in DOE Databases In the OSTI Collections: Earth System Models, Dr. William Watson DOE PAGESBeta - journal articles and accepted manuscripts resulting ...

  8. Power throttling of collections of computing elements

    DOE Patents [OSTI]

    Bellofatto, Ralph E. (Ridgefield, CT); Coteus, Paul W. (Yorktown Heights, NY); Crumley, Paul G. (Yorktown Heights, NY); Gara, Alan G. (Mount Kidsco, NY); Giampapa, Mark E. (Irvington, NY); Gooding; Thomas M. (Rochester, MN); Haring, Rudolf A. (Cortlandt Manor, NY); Megerian, Mark G. (Rochester, MN); Ohmacht, Martin (Yorktown Heights, NY); Reed, Don D. (Mantorville, MN); Swetz, Richard A. (Mahopac, NY); Takken, Todd (Brewster, NY)

    2011-08-16

    An apparatus and method for controlling power usage in a computer includes a plurality of computers communicating with a local control device, and a power source supplying power to the local control device and the computer. A plurality of sensors communicate with the computer for ascertaining power usage of the computer, and a system control device communicates with the computer for controlling power usage of the computer.

  9. Greenhouse gases emission from municipal waste management: The role of separate collection

    SciTech Connect (OSTI)

    Calabro, Paolo S.

    2009-07-15

    The municipal solid waste management significantly contributes to the emission in the atmosphere of greenhouse gases (e.g. CO{sub 2}, CH{sub 4}, N{sub 2}O) and therefore the management process from collection to treatment and disposal has to be optimized in order to reduce these emissions. In this paper, starting from the average composition of undifferentiated municipal solid waste in Italy, the effect of separate collection on greenhouse gases emissions from municipal waste management has been assessed. Different combinations of separate collection scenarios and disposal options (i.e. landfilling and incineration) have been considered. The effect of energy recovery from waste both in landfills and incinerators has also been addressed. The results outline how a separate collection approach can have a significant effect on the emission of greenhouse gases and how wise municipal solid waste management, implying the adoption of Best Available Technologies (i.e. biogas recovery and exploitation system in landfills and energy recovery system in Waste to Energy plants), can not only significantly reduce greenhouse gases emissions but, in certain cases, can also make the overall process a carbon sink. Moreover it has been shown that separate collection of plastic is a major issue when dealing with global warming relevant emissions from municipal solid waste management.

  10. Municipal solid waste source-separated collection in China: A comparative analysis

    SciTech Connect (OSTI)

    Tai Jun; Zhang Weiqian; Che Yue; Feng Di

    2011-08-15

    A pilot program focusing on municipal solid waste (MSW) source-separated collection was launched in eight major cities throughout China in 2000. Detailed investigations were carried out and a comprehensive system was constructed to evaluate the effects of the eight-year implementation in those cities. This paper provides an overview of different methods of collection, transportation, and treatment of MSW in the eight cities; as well as making a comparative analysis of MSW source-separated collection in China. Information about the quantity and composition of MSW shows that the characteristics of MSW are similar, which are low calorific value, high moisture content and high proportion of organisms. Differences which exist among the eight cities in municipal solid waste management (MSWM) are presented in this paper. Only Beijing and Shanghai demonstrated a relatively effective result in the implementation of MSW source-separated collection. While the six remaining cities result in poor performance. Considering the current status of MSWM, source-separated collection should be a key priority. Thus, a wider range of cities should participate in this program instead of merely the eight pilot cities. It is evident that an integrated MSWM system is urgently needed. Kitchen waste and recyclables are encouraged to be separated at the source. Stakeholders involved play an important role in MSWM, thus their responsibilities should be clearly identified. Improvement in legislation, coordination mechanisms and public education are problematic issues that need to be addressed.

  11. Bechtel Environmental Integrated Database Management System

    Energy Science and Technology Software Center (OSTI)

    1995-04-11

    Bechtel Environmental Integrated Data Management System (BEIDMS1.4) is an Oracle based relational database that stores data related to all aspects of environmental data collection.

  12. CAISI Operational Assessment (OA) data collection results. Final report

    SciTech Connect (OSTI)

    1997-01-31

    One of the lessons learned from Operation Desert Shield/Storm was the inability of deployed Combat Service Support (CSS) computers to exchange data effectively in a battlefield environment. The work-around solution to this previously identified problem has been to physically carry floppy disks between computers. A General Officer Steering Committee, directed by the Vice Chief of Staff of the Army, determined that immediate corrective action was necessary to ensure viability of the CSS Battlefield Mission Area. The study recommended that a three-phased system development plan address short-, mid- and long-term CSS automation communication interface requirements. In response to this study, Program Executive Office (PEO) Standard Army Management Information System (STAMIS) authorized the development of the CSS Automated Information System Interface (CAISI). Phase I (Near-Term) equipped the {open_quotes}first to fight{close_quotes} Contingency Corps units. Phase II (Mid-Term) is being fielded to the remainder of Force Package One units in the active force. Phase III (Long-Term) will equip the remaining units. CAISI is now in the early stages of Phase II fielding. Prior to full Phase II fielding, CAISI must be approved for production by a Milestone III decision authority. Part of the data that will be used in the Milestone III decision is a demonstration of the CAISI`s operational suitability, as assessed by the US Army Operational Test and Evaluation Command (OPTEC). This assessment will be performed through an Operational Assessment (OA) using data provided from previous technical testing, such as the CAISI Customer User Test (CUT), and a field training exercise conducted by units of the XVIII Airborne Corps. The field training exercise data collection took place during two events.

  13. Using DRASTIC'' to improve the accuracy of a geographical information system used for solid waste disposal facility siting: A case study

    SciTech Connect (OSTI)

    Padgett, D.A. . Dept. of Geography)

    1993-01-01

    Beginning in 1989, the citizens and commissioners of Alachua County, Florida began to develop a siting plan for a new solid waste disposal facility (SWDF). Through a cooperative effort with a private consulting firm, several evaluative criteria were selected and then translated into parameters for a geographical information system (GIS). Despite efforts to avoid vulnerable hydrogeology, the preferred site selected was in close proximity to the well field supplying Gainesville, Florida, home to approximately 75 percent of the county's population. The results brought forth a wave of protests from local residents claiming that leachate from the proposed SWDF would contaminate their drinking water. In this study, DRASTIC'' was applied in order to improve the accuracy and defensibility of the aquifer protection-based GIS parameters. DRASTIC'', a method for evaluating ground water contamination potential, is an acronym which stands for Depth to Water, Net Recharge, Aquifer Media, Soil Media, Topography, Impact of Vadose Zone Media, and Conductivity (Hydraulic)''.

  14. Work plan for the Oak Ridge National Laboratory groundwater program: Continuous groundwater collection

    SciTech Connect (OSTI)

    NONE

    1995-08-01

    The continuous collection of groundwater data is a basic and necessary part of Lockeheed Martin Energy Systems` ORNL Environmental Restoration Area-Wide Groundwater Program. Continuous groundwater data consist primarily of continually recorded groundwater levels, and in some instances, specific conductivity, pH, and/or temperature measurements. These data will be collected throughout the ORNL site. This Work Plan (WP) addresses technical objectives, equipment requirements, procedures, documentation requirements, and technical instructions for the acquisition of the continuous groundwater data. Intent of this WP is to provide an approved document that meets all the necessary requirements while retaining the flexibility necessary to effectively address ORNL`s groundwater problems.

  15. Control of the positional relationship between a sample collection instrument and a surface to be analyzed during a sampling procedure with image analysis

    DOE Patents [OSTI]

    Van Berkel, Gary J.; Kertesz, Vilmos

    2011-08-09

    A system and method utilizes an image analysis approach for controlling the collection instrument-to-surface distance in a sampling system for use, for example, with mass spectrometric detection. Such an approach involves the capturing of an image of the collection instrument or the shadow thereof cast across the surface and the utilization of line average brightness (LAB) techniques to determine the actual distance between the collection instrument and the surface. The actual distance is subsequently compared to a target distance for re-optimization, as necessary, of the collection instrument-to-surface during an automated surface sampling operation.

  16. Heat Flow Database Expansion for NGDS Data Development, Collection and

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Maintenance (SMU) | Department of Energy Heat Flow Database Expansion for NGDS Data Development, Collection and Maintenance (SMU) Heat Flow Database Expansion for NGDS Data Development, Collection and Maintenance (SMU) Heat Flow Database Expansion for NGDS Data Development, Collection and Maintenance (SMU) presentation at the April 2013 peer review meeting held in Denver, Colorado. PDF icon blackwell_smu_peer2013.pdf More Documents & Publications How to Utilize the National Geothermal

  17. COLLOQUIUM: Cybersnooping: Collection and Analysis of Metadata and Content

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    | Princeton Plasma Physics Lab November 20, 2013, 4:00pm to 5:15pm Colloquia MBG Auditorium COLLOQUIUM: Cybersnooping: Collection and Analysis of Metadata and Content Professor Edward Felten Princeton University Abstract: PDF icon COLL.11.20.13.pdf Recent reports indicate that governments (and perhaps others) have been collecting large amount of metadata and possibly content of phone calls, emails, and other communications. This talk will review what we know about current collection

  18. Center for Nanophase Materials Sciences (CNMS) - Collective Phenomena in

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Nanophases (CPN) COLLECTIVE PHENOMENA IN NANOPHASES The overarching research goal of the Collective Phenomena in Nanophases (CPN) theme is to understand how collective phenomena arise from correlations and fluctuations, confinement, and coordination across length and time scales, and to control these phenomena to produce complex functionality. In particular, we seek to understand the mechanism(s) whereby unique assemblies of atoms and molecules are formed under realistic conditions to enable

  19. Collecting Personally Identifiable Information Through the Web and User

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Research | Department of Energy Federal Requirements » Collecting Personally Identifiable Information Through the Web and User Research Collecting Personally Identifiable Information Through the Web and User Research The Office of Energy Efficiency and Renewable Energy (EERE) has requirements for websites, applications, customer surveys, and user experience (UX) research that collect data on individuals-also called personally identifiable information (PII). The U.S. Department of Energy

  20. Collective Impact for Zero Net Energy Homes | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Collective Impact for Zero Net Energy Homes Collective Impact for Zero Net Energy Homes This presentation was delivered at the U.S. Department of Energy Building America meeting on April 29-30, 2013, in Denver, Colorado. PDF icon collective_impact_znerh_rashkin.pdf More Documents & Publications Update on U.S. Department of Energy Building America Program Goals Update on U.S. Department of Energy Building America Program Goals Building America Roadmap to High

  1. Building America Webinar: Opportunities in Large Data Collection and

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Analysis-Presentation #3 | Department of Energy 3 Building America Webinar: Opportunities in Large Data Collection and Analysis-Presentation #3 This is the third presentation, Indoor Temperature and Humidity Data Collection and Analysis, in the webinar on April 16, 2014. PDF icon BA_Webinar_Booten_Metzger_Norton_4-16-14.pdf More Documents & Publications Building America Webinar: Opportunities in Large Data Collection and Analysis Building America Best Practices Series, Volume 7.3: Guide

  2. City of Fort Collins Comment on Information Collection Extension, October

    Office of Environmental Management (EM)

    2011 | Department of Energy City of Fort Collins Comment on Information Collection Extension, October 2011 City of Fort Collins Comment on Information Collection Extension, October 2011 The City of Fort Collins provided comments to the Department of Energy's notice of intent to seek approval of an extension of Information Collection 1910-5149 for Recovery Act Smart Grid Investment Grant reporting for four years, which was published in the Federal Register August 10, 2011, Vol. 76, No. 154,

  3. Energy Conservation Program: Data Collection and Comparison with...

    Energy Savers [EERE]

    EERE-2011-BT-NOA-0013 Energy Conservation Program: Data Collection and Comparison with Forecasted Unit Sales of Five Lamp Types AGENCY: Office of Energy Efficiency and Renewable ...

  4. DOE Collects Civil Penalties for Failure to Certify Consumer...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Consumer Refrigeration Products DOE Collects Civil Penalties for Failure to Certify ... DOE assessed civil penalties of 8,000 per manufacturer for first-time violators and civil ...

  5. DOE Collects Civil Penalties for Failure to Certify Commercial...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Commercial Refrigeration Equipment DOE Collects Civil Penalties for Failure to Certify ... DOE assessed civil penalties of 8,000 from both Atosa Catering Equipment, Inc. and RPI ...

  6. Carbon Cycling, Environmental & Rural Economic Impacts from Collecting...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Review March 24, 2015 Technology Area Review Steve Kelley, NCSU Rick Gustafson, U of WA Elaine Oneil, CORRIM Carbon Cycling, Environmental & Rural Economic Impacts from Collecting ...

  7. Concentrating Solar Power: Best Practices Handbook for the Collection...

    Open Energy Info (EERE)

    Power: Best Practices Handbook for the Collection and Use of Solar Resource Data Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Concentrating Solar Power: Best...

  8. Website Collects EMs D&D Lessons Learned

    Broader source: Energy.gov [DOE]

    WASHINGTON, D.C. EM is taking steps to collect lessons learned and best practices in the Cold War cleanup gained through the experience of its workforce.

  9. Category:Data Collection and Mapping | Open Energy Information

    Open Energy Info (EERE)

    (XRF) 1 pages M Macrophotography 1 pages P Portable X-Ray Diffraction (XRD) 1 pages Pages in category "Data Collection and Mapping" The following 6...

  10. Data Collection Requirements for the Federal Funding Accounting...

    Broader source: Energy.gov (indexed) [DOE]

    Policy Flash Data Collection Requirements for the Federal Funding Accounting and Transparency Act (FFATA) of 2006 More Documents & Publications Microsoft Word -...

  11. Interpretation of chemical analyses of waters collected from...

    Open Energy Info (EERE)

    chemical analyses of waters collected from two geothermal wells at Coso, California Jump to: navigation, search OpenEI Reference LibraryAdd to library Journal Article:...

  12. Heat Flow Database Expansion for NGDS Data Development, Collection...

    Open Energy Info (EERE)

    Database Expansion for NGDS Data Development, Collection and Maintenance Geothermal Project Jump to: navigation, search Last modified on July 22, 2011. Project Title Heat Flow...

  13. Hydraulic Fracturing Data Collection Tools Improve Environmental Reporting, Monitoring, Protection

    Broader source: Energy.gov [DOE]

    Two data collection tools specifically developed for hydraulic fracturing are available to help regulatory agencies monitor drilling and completion operations and enhance environmental protection.

  14. Utility Energy Service Contract Data Collection Template and Confidentiality Statement

    Broader source: Energy.gov [DOE]

    Template agencies and utilities can use to voluntarily collect utility energy service contract (UESC) project data for the Federal Energy Management Program.

  15. Document Details Document Number

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Document Details Document Number Date of Document Document Title/Description [Links below to each document] D195066340 Not listed. N/A REVISIONS IN STRATIGRAPHIC NOMENCLATURE OF COLUMBIA RIVER BASALT GROUP D196000240 Not listed. N/A EPA DENIAL OF LINER LEACHATE COLLECTION SYSTEM REQUIREMENTS D196005916 Not listed. N/A LATE CENOZOIC STRATIGRAPHY AND TECTONIC EVOLUTION WITHIN SUBSIDING BASIN SOUTH CENTRAL WASHINGTON D196025993 RHO-BWI-ST-14 N/A SUPRABASALT SEDIMENTS OF COLD CREEK SYNCLINE AREA

  16. Lower granite GIS data description and collection guidelines

    SciTech Connect (OSTI)

    Gordon, J.L.; Evans, B.J.; Perry, E.M.

    1995-12-01

    The Lower Granite Geographic Information System (GIS) was developed jointly by the US Army Corps of Engineers (USCOE) Walla Walla District and the Pacific Northwest Laboratory (PNL). The goal of the project is to use GIS technology to analyze impacts of the drawdown mitigation option on the physical and biological environment of the Lower Granite Reservoir. The drawdown mitigation option is based on the hypothesis that faster juvenile salmon travel to the ocean would result in higher juvenile survival and greater smolt-to-adult return ratios; to accomplish this, reservoir elevations would be lowered to increase channel velocities. Altering the elevation of the reservoirs on the Snake River is expected to have a variety of impacts to the Physical environment including changes to water velocity, temperature, dissolved gases, and turbidity. The GIS was developed to evaluate these changes and the resulting impacts on the anadromous and resident fish of the Snake River, as well as other aquatic organisms and terrestrial wildlife residing in the adjacent riparian areas. The Lower Granite GIS was developed using commercial hardware and software and is supported by a commercial relational database. Much of the initial system development involved collecting and incorporating data describing the river channel characteristics, hydrologic properties, and aquatic ecology. Potentially meaningful data for the Lower Granite GIS were identified and an extensive data search was performed. Data were obtained from scientists who are analyzing the habitats, limnology, and hydrology of the Snake River. The next six sections of this document describe the bathymetry, fish abundance, substrate, sediment chemistry, and channel hydrology data.

  17. Annual collectible energy of a two-axis tracking flat-plate solar collector

    SciTech Connect (OSTI)

    Attalage, R.A.; Reddy, T.A. )

    1992-01-01

    A correlation for annual collectible energy of a two-axis tracking flat-plate solar collector has been developed using simulated results based on typical meteorological year (TMY) data for 26 US locations. A preliminary validation of this correlation has been carried out with data from four Australian locations. With the advent of increasing interest in photovoltaic systems, there are a number of advantages of using a two-axis flat-plate collector. Since the tracking system is generally much cheaper than the collector panel, such a mode permits the incident solar radiation to be collected more efficiently. Incidence angle effects are minimized and, moreover, contrary to concentrating collectors, such a mode enables both the diffuse and beam components of solar radiation to be collected. In tropical locations where the diffuse fraction is generally high, this may be a great advantage. The objective of this study was to develop a correlation for the annual collectible energy of a two-axis tracking flat-plate collector.

  18. Significance of water fluxes in a deep arid-region vadose zone to waste disposal strategies

    SciTech Connect (OSTI)

    Johnejack, K.R.; Blout, D.O.; Sully, M.J.; Emer, D.F.; Hammermeister, D.P. [Reynolds Electrical and Engineering Co., Inc., Las Vegas, NV (United States); Dever, L.G.; O`Neill, L.J. [DOE Nevada Operations Office, Las Vegas, NV (United States). Waste Management Div.; Tyler, S.W. [Desert Research Institute, Reno, NV (United States). Water Resources Center; Chapman, J. [Desert Research Institute, Las Vegas, NV (United States). Water Resources Center

    1994-03-01

    Recently collected subsurface site characterization data have led to the development of a conceptual model of water movement beneath the Area 5 Radioactive Waste Management Site (RWMS) at the Nevada Test Site (NTS) that differs significantly from the conceptual model of water movement inherent in Resource Conservation and Recovery Act (RCRA) regulations. At the Area 5 RWMS, water fluxes in approximately the upper 75 m (250 ft) of the vadose zone point in the upward direction (rather than downward) which effectively isolates this region from the deep (approximately 250 m (820 ft)) uppermost aquifer. Standard RCRA approaches for detection and containment (groundwater monitoring and double liners/leachate collection/leak detection systems) are not able to fulfill their intended function in this rather unique hydrogeologic environment. In order to better fulfill the waste detection and containment intentions of RCRA for mixed waste disposal at the Area 5 RWMS, the Department of Energy, Nevada Operations Office (DOE/NV) is preparing a single petition for both a waiver from groundwater monitoring and an exemption from double liners with leachate collection/leak detection. DOE/NV proposes in this petition that the containment function of liners and leachate collection is better accomplished by the natural hydrogeologic processes operating in the upper vadose zone; and the detection function of groundwater monitoring and the leak detection system in liners is better fulfilled by an alternative vadose zone monitoring system. In addition, an alternative point of compliance is proposed that will aid in early detection, as well as limit the extent of potential contamination before detection. Finally, special cell design features and operation practices will be implemented to limit leachate formation, especially while the cell is open to the atmosphere during waste emplacement.

  19. Storing and managing information artifacts collected by information analysts using a computing device

    DOE Patents [OSTI]

    Pike, William A; Riensche, Roderick M; Best, Daniel M; Roberts, Ian E; Whyatt, Marie V; Hart, Michelle L; Carr, Norman J; Thomas, James J

    2012-09-18

    Systems and computer-implemented processes for storage and management of information artifacts collected by information analysts using a computing device. The processes and systems can capture a sequence of interactive operation elements that are performed by the information analyst, who is collecting an information artifact from at least one of the plurality of software applications. The information artifact can then be stored together with the interactive operation elements as a snippet on a memory device, which is operably connected to the processor. The snippet comprises a view from an analysis application, data contained in the view, and the sequence of interactive operation elements stored as a provenance representation comprising operation element class, timestamp, and data object attributes for each interactive operation element in the sequence.

  20. Computer memory management system

    DOE Patents [OSTI]

    Kirk, III, Whitson John

    2002-01-01

    A computer memory management system utilizing a memory structure system of "intelligent" pointers in which information related to the use status of the memory structure is designed into the pointer. Through this pointer system, The present invention provides essentially automatic memory management (often referred to as garbage collection) by allowing relationships between objects to have definite memory management behavior by use of coding protocol which describes when relationships should be maintained and when the relationships should be broken. In one aspect, the present invention system allows automatic breaking of strong links to facilitate object garbage collection, coupled with relationship adjectives which define deletion of associated objects. In another aspect, The present invention includes simple-to-use infinite undo/redo functionality in that it has the capability, through a simple function call, to undo all of the changes made to a data model since the previous `valid state` was noted.

  1. In the OSTI Collections: Quantum Chaos | OSTI, US Dept of Energy, Office of

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Scientific and Technical Information Quantum Chaos View Past "In the OSTI Collections" Articles. Article Acknowledgement: Dr. William N. Watson, Physicist DOE Office of Scientific and Technical Information The correspondence principle Billiards Chaos in specific quantum-physical systems Explorations of general theoretical concepts References Research Organizations Reports available through E-print Network Additional References The correspondence principle Any theory whose logical

  2. Financial and economic determinants of collective action: The case of wastewater management

    SciTech Connect (OSTI)

    Brunner, Norbert; Starkl, Markus

    2012-01-15

    Where public environmental funds support development of wastewater infrastructure, funding institutions ensure the economic use of funds, while the beneficiaries minimize their own costs. In rural areas, there is often a choice between decentralized or centralized (multi-village) systems: if the centralized system is most economic, then only this system is eligible for public funding. However, its implementation requires a voluntary cooperation of the concerned communities, who need to organize themselves to develop and run the infrastructure. The paper analyzes the social determinants of collaboration in a generic case study, using the following variables: method of (economic) assessment, modeled by the social discount rate, funding policy, modeled by the funding rate, and users' self-organization, modeled by cost sharing. In a borderline situation, where the centralized system turns out to be most economic, but this assessment is contingent on the assessment method, collective action may fail: the advantages of collective action from funding are too small to outweigh organizational deficiencies. Considering in this situation sanitation as a human right, authors recommend using innovative forms of organization and, if these fail, reassessing either the amount of funding or the eligibility for funding of more acceptable alternatives. - Highlights: Black-Right-Pointing-Pointer A generic case study models collective action and funding in wastewater management. Black-Right-Pointing-Pointer Determinants of success: economic assessment, funding policy and self-organization. Black-Right-Pointing-Pointer Success indicators: conflict rate, funds needed to make cost shares fair. Black-Right-Pointing-Pointer Method for analyzing centralized vs. decentralized disputes. Black-Right-Pointing-Pointer If collective action has less benefits, innovative cost sharing may ensure success.

  3. Microsoft Word - Wind Turbine CMMS Data Collection Recommendations - 2012-02-02b.docx

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    12-0828 Unlimited Release Printed February 2012 Supersedes SAND2009-4184 dated September 2009. Wind Energy Computerized Maintenance Management System (CMMS): Data Collection Recommendations for Reliability Analysis Valerie A. Peters, Alistair B. Ogilvie Wind Energy Technologies, Org-06121 Sandia National Laboratories P.O. Box 5800 Albuquerque, NM 87185-1124 Prepared by Sandia National Laboratories Albuquerque, New Mexico 87185 and Livermore, California 94550 Sandia National Laboratories is a

  4. SystemConfidence

    Energy Science and Technology Software Center (OSTI)

    2012-09-25

    SystemConfidence is a benchmark developed at ORNL which can measure statistical variation in which the user can plot. The portions of the code which manage the collection of the histograms and computing statistics on the histograms were designed with the intent that we could use these functions in other codes.

  5. Soil chemical sensor and precision agricultural chemical delivery system and method

    DOE Patents [OSTI]

    Colburn, J.W. Jr.

    1991-07-23

    A real time soil chemical sensor and precision agricultural chemical delivery system includes a plurality of ground-engaging tools in association with individual soil sensors which measure soil chemical levels. The system includes the addition of a solvent which rapidly saturates the soil/tool interface to form a conductive solution of chemicals leached from the soil. A multivalent electrode, positioned within a multivalent frame of the ground-engaging tool, applies a voltage or impresses a current between the electrode and the tool frame. A real-time soil chemical sensor and controller senses the electrochemical reaction resulting from the application of the voltage or current to the leachate, measures it by resistivity methods, and compares it against pre-set resistivity levels for substances leached by the solvent. Still greater precision is obtained by calibrating for the secondary current impressed through solvent-less soil. The appropriate concentration is then found and the servo-controlled delivery system applies the appropriate amount of fertilizer or agricultural chemicals substantially in the location from which the soil measurement was taken. 5 figures.

  6. Soil chemical sensor and precision agricultural chemical delivery system and method

    DOE Patents [OSTI]

    Colburn, Jr., John W. (Houston, TX)

    1991-01-01

    A real time soil chemical sensor and precision agricultural chemical delivery system includes a plurality of ground-engaging tools in association with individual soil sensors which measure soil chemical levels. The system includes the addition of a solvent which rapidly saturates the soil/tool interface to form a conductive solution of chemicals leached from the soil. A multivalent electrode, positioned within a multivalent frame of the ground-engaging tool, applies a voltage or impresses a current between the electrode and the tool frame. A real-time soil chemical sensor and controller senses the electrochemical reaction resulting from the application of the voltage or current to the leachate, measures it by resistivity methods, and compares it against pre-set resistivity levels for substances leached by the solvent. Still greater precision is obtained by calibrating for the secondary current impressed through solvent-less soil. The appropriate concentration is then found and the servo-controlled delivery system applies the appropriate amount of fertilizer or agricultural chemicals substantially in the location from which the soil measurement was taken.

  7. Shaft seal system

    DOE Patents [OSTI]

    Kapich, Davorin D. (Carlsbad, CA)

    1985-01-01

    A shaft seal system is disclosed for isolating two regions of different fluid mediums through which a rotatable shaft extends. The seal system includes a seal housing through which the shaft extends and which defines an annular land and an annular labyrinth both of which face on the shaft so that each establishes a corresponding fluid sealing annulus. A collection cavity is formed in communication with the annular sealing spaces, and fluids compatible with the fluids in each of the two regions to be isolated are introduced, respectively, into the annular sealing spaces and collected in the collection cavity from which the fluid mixture is removed and passed to a separator which separates the fluids and returns them to their respective annular sealing spaces in a recycling manner. In the illustrated embodiment, the isolated fluid mediums comprise a liquid region and a gas region. Gas is removed from the gas region and passed through a purifier and a gas pump operative to introduce the purified gas through the labyrinth sealing annulus to the collection cavity. After passing to the separator, the separated gas is passed through a dryer from which the dried gas is caused to pass through the labyrinth sealing annulus into the collection cavity independently of the purified gas so as to insure isolation of the gas region in the event of sealing gas pump malfunction.

  8. Computer systems and software description for gas characterization system

    SciTech Connect (OSTI)

    Vo, C.V.

    1997-04-01

    The Gas Characterization System Project was commissioned by TWRS management with funding from TWRS Safety, on December 1, 1994. The project objective is to establish an instrumentation system to measure flammable gas concentrations in the vapor space of selected watch list tanks, starting with tank AN-105 and AW-101. Data collected by this system is meant to support first tank characterization, then tank safety. System design is premised upon Characterization rather than mitigation, therefore redundancy is not required.

  9. Operational experience using the novel FixCup collecting main valve

    SciTech Connect (OSTI)

    Giertz, J.; Huhn, F.; Spitz, J.

    1996-12-31

    On the occasion of the 1995 AIME conference the new PROven (Pressure Regulated Oven) process to control the pressure in coke ovens individually was introduced. This process was made feasible with a new collecting main valve, termed FixCup, with the aid of this valve a variable flow resistance to the raw gas discharge can be realized using a water immersion system. However, just the application of the FixCup system alone--without any pressure regulation--is very advantageous and cost saving. Thyssen has equipped 30 ovens with the new valve. The special constructive features as well as the operational experience using the FixCup valve are treated.

  10. Collective motion of two-electron atom in hyperspherical adiabatic approximation

    SciTech Connect (OSTI)

    Mohamed, A. S.; Nikitin, S. I.

    2015-03-30

    This work is devoted to calculate bound states in the two-electron atoms. The separation of variables has carried out in hyper spherical coordinate system (R, ?, ?). Assuming collective motion of the electrons, where the hper angle (???/4) and (???). The separation of the rotational variables leads to system of differential equations with more simple form as compared with non restricted motion. Energy of doubly excited P{sup e} and D{sup 0} states are calculated semi classically by using quantization condition of Bohr -Somerfield. The results compared with previously published data.

  11. NREL Offers an Open-Source Solution for Large-Scale Energy Data Collection

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and Analysis - News Releases | NREL NREL Offers an Open-Source Solution for Large-Scale Energy Data Collection and Analysis June 18, 2013 The Energy Department's National Renewable Energy Laboratory (NREL) is launching an open-source system for storing, integrating, and aligning energy-related time-series data. NREL's Energy DataBus is used for tracking and analyzing energy use on its own campus. The system is applicable to other facilities-including anything from a single building to a

  12. Determining collective barrier operation skew in a parallel computer

    DOE Patents [OSTI]

    Faraj, Daniel A.

    2015-11-24

    Determining collective barrier operation skew in a parallel computer that includes a number of compute nodes organized into an operational group includes: for each of the nodes until each node has been selected as a delayed node: selecting one of the nodes as a delayed node; entering, by each node other than the delayed node, a collective barrier operation; entering, after a delay by the delayed node, the collective barrier operation; receiving an exit signal from a root of the collective barrier operation; and measuring, for the delayed node, a barrier completion time. The barrier operation skew is calculated by: identifying, from the compute nodes' barrier completion times, a maximum barrier completion time and a minimum barrier completion time and calculating the barrier operation skew as the difference of the maximum and the minimum barrier completion time.

  13. Determining collective barrier operation skew in a parallel computer

    DOE Patents [OSTI]

    Faraj, Daniel A.

    2015-12-24

    Determining collective barrier operation skew in a parallel computer that includes a number of compute nodes organized into an operational group includes: for each of the nodes until each node has been selected as a delayed node: selecting one of the nodes as a delayed node; entering, by each node other than the delayed node, a collective barrier operation; entering, after a delay by the delayed node, the collective barrier operation; receiving an exit signal from a root of the collective barrier operation; and measuring, for the delayed node, a barrier completion time. The barrier operation skew is calculated by: identifying, from the compute nodes' barrier completion times, a maximum barrier completion time and a minimum barrier completion time and calculating the barrier operation skew as the difference of the maximum and the minimum barrier completion time.

  14. Collection and Analysis of Reservoir Data from Testing and Operation...

    Open Energy Info (EERE)

    Reservoir Data from Testing and Operation of the Raft River 5 MW Power Plant Jump to: navigation, search OpenEI Reference LibraryAdd to library Conference Proceedings: Collection...

  15. OVIS: Scalable Run Time Data Collection Analysis and Visualization

    Office of Scientific and Technical Information (OSTI)

    (Abstract). (Conference) | SciTech Connect OVIS: Scalable Run Time Data Collection Analysis and Visualization (Abstract). Citation Details In-Document Search Title: OVIS: Scalable Run Time Data Collection Analysis and Visualization (Abstract). Abstract not provided. Authors: Chen, Frank Xiaoxiao ; Das, Ananya Publication Date: 2009-07-01 OSTI Identifier: 1141424 Report Number(s): SAND2009-4761C 506638 DOE Contract Number: DE-AC04-94AL85000 Resource Type: Conference Resource Relation:

  16. Mapping quadrupole collectivity in the Cd isotopes: The breakdown of

    Office of Scientific and Technical Information (OSTI)

    harmonic vibrational motion (Journal Article) | SciTech Connect Mapping quadrupole collectivity in the Cd isotopes: The breakdown of harmonic vibrational motion Citation Details In-Document Search Title: Mapping quadrupole collectivity in the Cd isotopes: The breakdown of harmonic vibrational motion The stable Cd isotopes have long been used as paradigms for spherical vibrational motion. Extensive investigations with in-beam {gamma} spectroscopy have resulted in very-well-established level

  17. Collective Dissipation from Saddle to Scission in a Microscopic Approach

    Office of Scientific and Technical Information (OSTI)

    (Technical Report) | SciTech Connect Collective Dissipation from Saddle to Scission in a Microscopic Approach Citation Details In-Document Search Title: Collective Dissipation from Saddle to Scission in a Microscopic Approach Authors: Younes, W ; Gogny, D Publication Date: 2012-09-28 OSTI Identifier: 1053675 Report Number(s): LLNL-TR-586694 DOE Contract Number: W-7405-ENG-48 Resource Type: Technical Report Research Org: Lawrence Livermore National Laboratory (LLNL), Livermore, CA Sponsoring

  18. DOE Collections, Office of Scientific and Technical Information, USDOE

    Office of Scientific and Technical Information (OSTI)

    DOE Collections At OSTI you can find research results and science information from the Manhattan Project to the present, download documents, view energy citations, discover patents and e-prints, read about ongoing DOE accomplishments, search multimedia, science conference proceedings, scientific research data, and software, and connect to federated search of DOE collections, U.S., and global science portals, as well as customized resources. SciTech Connect Information Bridge DOE R&D

  19. Diffusion in confinement: kinetic simulations of self- and collective

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    diffusion behavior of adsorbed gases | Center for Gas SeparationsRelevant to Clean Energy Technologies | Blandine Jerome confinement: kinetic simulations of self- and collective diffusion behavior of adsorbed gases Previous Next List M. K. F. Abouelnasr and B. Smit, PCCP 14 (33), 11600 (2012) DOI: 10.1039/C2CP41147D abo121 Abstract The self- and collective-diffusion behaviors of adsorbed methane, helium, and isobutane in zeolite frameworks LTA, MFI, AFI, and SAS were examined at various

  20. Data Collection for Improved Cold Temperature Thermal Modeling and Strategy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Development | Department of Energy Modeling and Strategy Development Data Collection for Improved Cold Temperature Thermal Modeling and Strategy Development 2011 DOE Hydrogen and Fuel Cells Program, and Vehicle Technologies Program Annual Merit Review and Peer Evaluation PDF icon vss050_jehlik_2011_o.pdf More Documents & Publications Data Collection for Improved Cold Temperature Thermal Modeling Energy Management Strategies for Fast Battery Temperature Rise and Engine Efficiency

  1. Data Collection for Improved Cold Temperature Thermal Modeling | Department

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    of Energy Modeling Data Collection for Improved Cold Temperature Thermal Modeling 2012 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting PDF icon vss088_jehlik_2012_p.pdf More Documents & Publications Data Collection for Improved Cold Temperature Thermal Modeling and Strategy Development Advanced Technology Vehicle Lab Benchmarking - Level 2 (in-depth)

  2. Scalable Run Time Data Collection Analysis and Visualization

    Office of Scientific and Technical Information (OSTI)

    (Presentation). (Conference) | SciTech Connect Scalable Run Time Data Collection Analysis and Visualization (Presentation). Citation Details In-Document Search Title: Scalable Run Time Data Collection Analysis and Visualization (Presentation). Abstract not provided. Authors: Gentile, Ann C. ; Chen, Frank Xiaoxiao [1] ; Das, Ananya + Show Author Affiliations Sandia National Laboratories, Livermore, CA [Sandia National Laboratories, Livermore, CA Publication Date: 2009-07-01 OSTI Identifier:

  3. Building America Webinar: Opportunities in Large Data Collection and

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Analysis | Department of Energy Analysis Building America Webinar: Opportunities in Large Data Collection and Analysis This introductory presentation for the webinar held on April 16, 2014, gives an overview of the Building America program and the webinar. PDF icon BA_Webinar_Intro_4-16-14.pdf More Documents & Publications Building America Webinar: Opportunities in Large Data Collection and Analysis Building America Webinar: Retrofitting Central Space Conditioning Strategies for

  4. Truck Duty Cycle and Performance Data Collection and Analysis Program |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy 1 DOE Hydrogen and Fuel Cells Program, and Vehicle Technologies Program Annual Merit Review and Peer Evaluation PDF icon vss002_knee_2011_o.pdf More Documents & Publications Truck Duty Cycle and Performance Data Collection and Analysis Program Heavy Duty & Medium Duty Drive Cycle Data Collection for Modeling Expansion Roadmap and Technical White Papers for 21st Century Truck Partnership

  5. Building America Webinar: Opportunities in Large Data Collection and

    Energy Savers [EERE]

    Analysis | Department of Energy Opportunities in Large Data Collection and Analysis Building America Webinar: Opportunities in Large Data Collection and Analysis The webinar, presented on April 16, 2014, focused on specific Building America projects that are looking to gather and analyze large bodies of data on new and existing homes, and discussed opportunities for industry to collaborate with researchers to gather and analyze valuable data. View the presentations: Introduction and Building

  6. DOE Collects Civil Penalties for Failure to Certify Compliance | Department

    Energy Savers [EERE]

    of Energy Collects Civil Penalties for Failure to Certify Compliance DOE Collects Civil Penalties for Failure to Certify Compliance March 4, 2016 - 6:06pm Addthis DOE recently resolved enforcement actions against a variety of companies for failure to certify that the products they were distributing meet the applicable energy or water conservation standards. DOE found that Utility Refrigerator had failed to certify the compliance of its commercial refrigeration equipment, Fujitsu General

  7. Proposed Agency Information Collection: Federal Register Notice Volume 76,

    Energy Savers [EERE]

    No. 154 - Aug. 10, 2011 | Department of Energy 54 - Aug. 10, 2011 Proposed Agency Information Collection: Federal Register Notice Volume 76, No. 154 - Aug. 10, 2011 The Department of Energy (DOE) invites public comment on DOE's intent to request OMB to renew Information Collection Request Title: OE Recovery Act Financial Assistance Grants, OMB Control No. 1910-5149 for an additional four years that DOE is developing for submission to the Office of Management and Budget (OMB) pursuant to the

  8. DOE Collects Civil Penalties for Failure to Certify Commercial

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Refrigeration Equipment | Department of Energy Collects Civil Penalties for Failure to Certify Commercial Refrigeration Equipment DOE Collects Civil Penalties for Failure to Certify Commercial Refrigeration Equipment November 18, 2015 - 11:54am Addthis The General Counsel's enforcement office recently resolved enforcement actions against two companies that failed to submit required reports to certify that their commercial refrigeration equipment complies with federal energy conservation

  9. DOE Technical Standards Archived Collection | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Technical Standards Archived Collection DOE Technical Standards Archived Collection Document ID Filter Document ID sort descending Title Date DOE-HDBK-1131-2007 General Employee Radiological Training Replaced by DOE-HDBK-1131-2007 (CN1) (Reaffirmed 2013) This handbook describes the DOE General Employee Radiological Training program. It is intended for use by DOE contractors for the development of facility-specific general employee radiological training. 01/15/2008 DOE-HDBK-1131-98 General

  10. Optical Design Considerations for Efficient Light Collection from Liquid Scintillation Counters

    SciTech Connect (OSTI)

    Bernacki, Bruce E.; Douglas, Matthew; Erchinger, Jennifer L.; Fuller, Erin S.; Keillor, Martin E.; Morley, Shannon M.; Mullen, Crystal A.; Orrell, John L.; Panisko, Mark E.; Warren, Glen A.; Wright, Michael E.

    2015-01-01

    Liquid scintillation counters measure charged particle-emitting radioactive isotopes and are used for environmental studies, nuclear chemistry, and life science. Alpha and beta emissions arising from the material under study interact with the scintillation cocktail to produce light. The prototypical liquid scintillation counter employs low-level photon-counting detectors to measure the arrival of the scintillation light produced as a result of the dissolved material under study interacting with the scintillation cocktail. For reliable operation the counting instrument must convey the scintillation light to the detectors efficiently and predictably. Current best practices employ the use of two or more detectors for coincidence processing to discriminate true scintillation events from background events due to instrumental effects such as photomultiplier tube dark rates, tube flashing, or other light emission not generated in the scintillation cocktail vial. In low background liquid scintillation counters additional attention is paid to shielding the scintillation cocktail from naturally occurring radioactive material (NORM) present in the laboratory and within the instruments construction materials. Low background design is generally at odds with optimal light collection. This study presents the evolution of a light collection design for liquid scintillation counting in a low background shield. The basic approach to achieve both good light collection and a low background measurement is described. The baseline signals arising from the scintillation vial are modeled and methods to efficiently collect scintillation light are presented as part of the development of a customized low-background, high sensitivity liquid scintillation counting system.

  11. Using Public Participation to Improve MELs Energy Data Collection

    SciTech Connect (OSTI)

    Cheung, Iris; Kloss, Margarita; Brown, Rich; Meier, Alan

    2014-03-11

    Miscellaneous Electric Loads (MELs) have proliferated in the last decade, and comprise an increasing share of building energy consumption. Because of the diversity of MELs and our lack of understanding about how people use them, large-scale data collection is needed to inform meaningful energy reduction strategies. Traditional methods of data collection, however, usually incur high labor and metering equipment expenses. As an alternative, this paper investigates the feasibility of crowdsourcing data collection to satisfy at least part of the data collection needs with acceptable accuracy. This study assessed the reliability and accuracy of crowdsourced data, by recruiting over 20 volunteers (from the 2012 Lawrence Berkeley Lab, Open House event) to test our crowdsourcing protocol. The protocol asked volunteers to perform the following tasks for three test products with increasing complexity - record power meter and product characteristics, identify all power settings available, and report the measured power. Based on our collected data and analysis, we concluded that volunteers performed reasonably well for devices with functionalities with which they are familiar, and might not produce highly accurate field measurements for complex devices. Accuracy will likely improve when participants are measuring the power used by devices in their home which they know how to operate, by providing more specific instructions including instructional videos. When integrated with existing programs such as the Home Energy Saver tool, crowdsourcing data collection from individual homeowners has the potential to generate a substantial amount of information about MELs energy use in homes.

  12. Mechanism of supporting sub-communicator collectives with O(64) counters as opposed to one counter for each sub-communicator

    DOE Patents [OSTI]

    Kumar, Sameer; Mamidala, Amith R.; Ratterman, Joseph D.; Blocksome, Michael; Miller, Douglas

    2013-09-03

    A system and method for enhancing barrier collective synchronization on a computer system comprises a computer system including a data storage device. The computer system includes a program stored in the data storage device and steps of the program being executed by a processor. The system includes providing a plurality of communicators for storing state information for a bather algorithm. Each communicator designates a master core in a multi-processor environment of the computer system. The system allocates or designates one counter for each of a plurality of threads. The system configures a table with a number of entries equal to the maximum number of threads. The system sets a table entry with an ID associated with a communicator when a process thread initiates a collective. The system determines an allocated or designated counter by searching entries in the table.

  13. OpenSM Monitoring System

    Energy Science and Technology Software Center (OSTI)

    2015-04-17

    The OpenSM Monitoring System includes a collection of diagnostic and monitoring tools for use on Infiniband networks. The information this system gathers is obtained from a service, which in turn is obtained directly from the OpenSM subnet manager.

  14. Application of bar codes to the automation of analytical sample data collection

    SciTech Connect (OSTI)

    Jurgensen, H A

    1986-01-01

    The Health Protection Department at the Savannah River Plant collects 500 urine samples per day for tritium analyses. Prior to automation, all sample information was compiled manually. Bar code technology was chosen for automating this program because it provides a more accurate, efficient, and inexpensive method for data entry. The system has three major functions: sample labeling is accomplished at remote bar code label stations composed of an Intermec 8220 (Intermec Corp.) interfaced to an IBM-PC, data collection is done on a central VAX 11/730 (Digital Equipment Corp.). Bar code readers are used to log-in samples to be analyzed on liquid scintillation counters. The VAX 11/730 processes the data and generates reports, data storage is on the VAX 11/730 and backed up on the plant's central computer. A brief description of several other bar code applications at the Savannah River Plant is also presented.

  15. Mechanism to support generic collective communication across a variety of programming models

    DOE Patents [OSTI]

    Almasi, Gheorghe (Ardsley, NY); Dozsa, Gabor (Ardsley, NY); Kumar, Sameer (White Plains, NY)

    2011-07-19

    A system and method for supporting collective communications on a plurality of processors that use different parallel programming paradigms, in one aspect, may comprise a schedule defining one or more tasks in a collective operation, an executor that executes the task, a multisend module to perform one or more data transfer functions associated with the tasks, and a connection manager that controls one or more connections and identifies an available connection. The multisend module uses the available connection in performing the one or more data transfer functions. A plurality of processors that use different parallel programming paradigms can use a common implementation of the schedule module, the executor module, the connection manager and the multisend module via a language adaptor specific to a parallel programming paradigm implemented on a processor.

  16. Using Public Participation to Improve MELs Energy Data Collection

    SciTech Connect (OSTI)

    Kloss, Margarita; Cheung, Iris; Brown, Richard; Meier, Alan

    2014-08-11

    Miscellaneous and electronic loads (MELs) comprise an increasing share of building energy consumption. Large-scale data collection is needed to inform meaningful energy reduction strategies because of the diversity of MELs and our lack of understanding about how people use them. Traditional methods of data collection, however, usually incur high labor and metering equipment expenses. As an alternative, this paper investigates the feasibility of crowdsourcing data collection to satisfy at least part of the data collection needs with acceptable accuracy. We assessed the reliability and accuracy of crowd-sourced data by recruiting 18 volunteers and testing our crowdsourcing protocol. The protocol asked volunteers to perform measurement tasks for three MELs devices of increasing complexity 1) record power meter and MELs product characteristics, 2) identify and measure all power modes available, and 3) report the measured power. Volunteers performed reasonably well for devices with functionalities with which they were familiar, but many could not correctly identify all available power modes in complex devices. Accuracy may improve when participants measure the power used by familiar devices in their home, or by providing more specific instructions, e.g. videos. Furthermore, crowdsourcing data collection from individual homeowners has the potential to generate valuable information about MELs energy use in homes when integrated with existing programs such as Home Energy Saver and Building America.

  17. North American Industry Classification System (NAICS) Search Tool

    Broader source: Energy.gov [DOE]

    The North American Industry Classification System (NAICS) is the standard used by Federal statistical agencies in classifying business establishments for the purpose of collecting, analyzing, and...

  18. Toward a new metric for ranking high performance computing systems...

    Office of Scientific and Technical Information (OSTI)

    as a true measure of system performance for a growing collection of important science and engineering applications. In this paper we describe a new high performance conjugate...

  19. Collective Memory Transfers for Multi-Core Chips

    SciTech Connect (OSTI)

    Michelogiannakis, George; Williams, Alexander; Shalf, John

    2013-11-13

    Future performance improvements for microprocessors have shifted from clock frequency scaling towards increases in on-chip parallelism. Performance improvements for a wide variety of parallel applications require domain-decomposition of data arrays from a contiguous arrangement in memory to a tiled layout for on-chip L1 data caches and scratchpads. How- ever, DRAM performance suffers under the non-streaming access patterns generated by many independent cores. We propose collective memory scheduling (CMS) that actively takes control of collective memory transfers such that requests arrive in a sequential and predictable fashion to the memory controller. CMS uses the hierarchically tiled arrays formal- ism to compactly express collective operations, which greatly improves programmability over conventional prefetch or list- DMA approaches. CMS reduces application execution time by up to 32% and DRAM read power by 2.2, compared to a baseline DMA architecture such as STI Cell.

  20. Solarize Guidebook: A Community Guide to Collective Purchasing of Residential PV Systems (Book)

    SciTech Connect (OSTI)

    Not Available

    2012-05-01

    This guidebook is intended as a road map for project planners and solar advocates who want to convert 'interest' into 'action,' to break through market barriers and permanently transform the market for residential solar installations in their communities. It describes the key elements of the Solarize campaigns in Portland, and offers several program refinements from projects beyond Portland. The guidebook provides lessons, considerations, and step-by-step plans for project organizers to replicate the success of Solarize Portland.

  1. Steam System Balancing and Tuning for Multifamily Residential Buildings in Chicagoland - Second Year of Data Collection

    SciTech Connect (OSTI)

    Choi, Jayne; Ludwig, Peter; Brand, Larry

    2013-08-01

    Steam heated buildings often suffer from uneven heating as a result of poor control of the amount of steam entering each radiator. In order to satisfy the heating load to the coldest units, other units are overheated. As a result, some tenants complain of being too hot and open their windows in the middle of winter, while others complain of being too cold and are compelled to use supplemental heat sources.

  2. Solarize Guidebook: A Community Guide to Collective Purchasing of Residential PV Systems

    SciTech Connect (OSTI)

    Irvine, L.; Sawyer, A.; Grove, J.

    2011-02-01

    This handbook is intended as a road map for project planners and solar advocates who want to convert interest into action, to break through market barriers and permanently transform the market for residential solar installations in their communities. It describes the key elements of the Solarize campaigns in Portland, and offers several program refinements from projects beyond Portland. The handbook provides lessons, considerations, and step-by-step plans for project organizers to replicate the success of Solarize Portland.

  3. LM to Meet Energy Metering Goals Through Enhanced Data Collection at Groundwater Treatment Systems

    Broader source: Energy.gov [DOE]

    The federal government, including the U.S. Department of Energy (DOE) Office of Legacy Management (LM), has been challenged by Executive and DOE orders to reach two goals related to energy usage...

  4. Collection of liquid from below-ground location

    DOE Patents [OSTI]

    Phillips, Steven J. (Kennewick, WA); Alexander, Robert G. (Kennewick, WA)

    1995-01-01

    A method of retrieving liquid from a below-ground collection area by permitting gravity flow of the liquid from the collection area to a first closed container; monitoring the level of the liquid in the closed container; and after the liquid reaches a given level in the first closed container, transferring the liquid to a second closed container disposed at a location above the first closed container, via a conduit, by introducing into the first closed container a gas which is substantially chemically inert with respect to the liquid, the gas being at a pressure sufficient to propel the liquid from the first closed container to the second closed container.

  5. Portable data collection device with self identifying probe

    DOE Patents [OSTI]

    French, P.D.

    1998-11-17

    The present invention provides a portable data collection device that has a variety of sensors that are interchangeable with a variety of input ports in the device. The various sensors include a data identification feature that provides information to the device regarding the type of physical data produced by each sensor and therefore the type of sensor itself. The data identification feature enables the device to locate the input port where the sensor is connected and self adjust when a sensor is removed or replaced. The device is able to collect physical data, whether or not a function of time. The sensor may also store a unique sensor identifier. 13 figs.

  6. Hardware support for collecting performance counters directly to memory

    DOE Patents [OSTI]

    Gara, Alan; Salapura, Valentina; Wisniewski, Robert W.

    2012-09-25

    Hardware support for collecting performance counters directly to memory, in one aspect, may include a plurality of performance counters operable to collect one or more counts of one or more selected activities. A first storage element may be operable to store an address of a memory location. A second storage element may be operable to store a value indicating whether the hardware should begin copying. A state machine may be operable to detect the value in the second storage element and trigger hardware copying of data in selected one or more of the plurality of performance counters to the memory location whose address is stored in the first storage element.

  7. Portable data collection device with self identifying probe

    DOE Patents [OSTI]

    French, Patrick D.

    1998-01-01

    The present invention provides a portable data collection device that has a variety of sensors that are interchangeable with a variety of input ports in the device. The various sensors include a data identification feature that provides information to the device regarding the type of physical data produced by each sensor and therefore the type of sensor itself. The data identification feature enables the device to locate the input port where the sensor is connected and self adjust when a sensor is removed or replaced. The device is able to collect physical data, whether or not a function of time. The sensor may also store a unique sensor identifier.

  8. HB-Line Plutonium Oxide Data Collection Strategy

    SciTech Connect (OSTI)

    Watkins, R.; Varble, J.; Jordan, J.

    2015-05-26

    HB-Line and H-Canyon will handle and process plutonium material to produce plutonium oxide for feed to the Mixed Oxide Fuel Fabrication Facility (MFFF). However, the plutonium oxide product will not be transferred to the MFFF directly from HB-Line until it is packaged into a qualified DOE-STD-3013-2012 container. In the interim, HB-Line will load plutonium oxide into an inner, filtered can. The inner can will be placed in a filtered bag, which will be loaded into a filtered outer can. The outer can will be loaded into a certified 9975 with getter assembly in compliance with onsite transportation requirement, for subsequent storage and transfer to the K-Area Complex (KAC). After DOE-STD-3013-2012 container packaging capabilities are established, the product will be returned to HB-Line to be packaged into a qualified DOE-STD-3013-2012 container. To support the transfer of plutonium oxide to KAC and then eventually to MFFF, various material and packaging data will have to be collected and retained. In addition, data from initial HB-Line processing operations will be needed to support future DOE-STD-3013-2012 qualification as amended by the HB-Line DOE Standard equivalency. As production increases, the volume of data to collect will increase. The HB-Line data collected will be in the form of paper copies and electronic media. Paper copy data will, at a minimum, consist of facility procedures, nonconformance reports (NCRs), and DCS print outs. Electronic data will be in the form of Adobe portable document formats (PDFs). Collecting all the required data for each plutonium oxide can will be no small effort for HB-Line, and will become more challenging once the maximum annual oxide production throughput is achieved due to the sheer volume of data to be collected. The majority of the data collected will be in the form of facility procedures, DCS print outs, and laboratory results. To facilitate complete collection of this data, a traveler form will be developed which identifies the required facility procedures, DCS print outs, and laboratory results needed to assemble a final data package for each HB-Line plutonium oxide interim oxide can. The data traveler may identify the specific values (data) required to be extracted from the collected facility procedures and DCS print outs. The data traveler may also identify associated criteria to be checked. Inevitably there will be procedure anomalies during the course of the HB-Line plutonium oxide campaign that will have to be addressed in a timely manner.

  9. Unusual Layer-Dependent Charge Distribution, Collective Mode Coupling, and

    Office of Scientific and Technical Information (OSTI)

    Superconductivity in Multilayer Cuprate Ba2Ca3Cu4O8F2 (Journal Article) | SciTech Connect Layer-Dependent Charge Distribution, Collective Mode Coupling, and Superconductivity in Multilayer Cuprate Ba2Ca3Cu4O8F2 Citation Details In-Document Search Title: Unusual Layer-Dependent Charge Distribution, Collective Mode Coupling, and Superconductivity in Multilayer Cuprate Ba2Ca3Cu4O8F2 Low energy ultrahigh momentum resolution angle resolved photoemission spectroscopy study on four-layer self-doped

  10. Unusual layer-dependent charge distribution, collective mode coupling, and

    Office of Scientific and Technical Information (OSTI)

    superconductivity in multilayer cuprate Ba2Ca3Cu4O8F2 (Journal Article) | SciTech Connect layer-dependent charge distribution, collective mode coupling, and superconductivity in multilayer cuprate Ba2Ca3Cu4O8F2 Citation Details In-Document Search Title: Unusual layer-dependent charge distribution, collective mode coupling, and superconductivity in multilayer cuprate Ba2Ca3Cu4O8F2 Low energy ultrahigh momentum resolution angle resolved photoemission spectroscopy study on four-layer self-doped

  11. Reducing power consumption while performing collective operations on a plurality of compute nodes

    DOE Patents [OSTI]

    Archer, Charles J. (Rochester, MN); Blocksome, Michael A. (Rochester, MN); Peters, Amanda E. (Rochester, MN); Ratterman, Joseph D. (Rochester, MN); Smith, Brian E. (Rochester, MN)

    2011-10-18

    Methods, apparatus, and products are disclosed for reducing power consumption while performing collective operations on a plurality of compute nodes that include: receiving, by each compute node, instructions to perform a type of collective operation; selecting, by each compute node from a plurality of collective operations for the collective operation type, a particular collective operation in dependence upon power consumption characteristics for each of the plurality of collective operations; and executing, by each compute node, the selected collective operation.

  12. Collisions of deformable cells lead to collective migration

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Löber, Jakob; Ziebert, Falko; Aranson, Igor S.

    2015-03-17

    Collective migration of eukaryotic cells plays a fundamental role in tissue growth, wound healing and immune response. The motion, arising spontaneously or in response to chemical and mechanical stimuli, is also important for understanding life-threatening pathologies, such as cancer and metastasis formation. We present a phase-field model to describe the movement of many self-organized, interacting cells. The model takes into account the main mechanisms of cell motility – acto-myosin dynamics, as well as substrate-mediated and cell-cell adhesion. It predicts that collective cell migration emerges spontaneously as a result of inelastic collisions between neighboring cells: collisions lead to a mutual alignmentmore » of the cell velocities and to the formation of coherently-moving multi-cellular clusters. Small cell-to-cell adhesion, in turn, reduces the propensity for large-scale collective migration, while higher adhesion leads to the formation of moving bands. Our study provides valuable insight into biological processes associated with collective cell motility.« less

  13. DOE Hosts Festival to Collect Items for Area Food Banks

    Broader source: Energy.gov [DOE]

    WASHINGTON, D.C. – Deputy Secretary of Energy Daniel Poneman and a representative of the Capital Area Food Bank are among the guest speakers at an event this Tuesday, July 31, to collect food items for the DOE Feeds Families drive.

  14. Collisions of deformable cells lead to collective migration

    SciTech Connect (OSTI)

    Löber, Jakob; Ziebert, Falko; Aranson, Igor S.

    2015-03-17

    Collective migration of eukaryotic cells plays a fundamental role in tissue growth, wound healing and immune response. The motion, arising spontaneously or in response to chemical and mechanical stimuli, is also important for understanding life-threatening pathologies, such as cancer and metastasis formation. We present a phase-field model to describe the movement of many self-organized, interacting cells. The model takes into account the main mechanisms of cell motility – acto-myosin dynamics, as well as substrate-mediated and cell-cell adhesion. It predicts that collective cell migration emerges spontaneously as a result of inelastic collisions between neighboring cells: collisions lead to a mutual alignment of the cell velocities and to the formation of coherently-moving multi-cellular clusters. Small cell-to-cell adhesion, in turn, reduces the propensity for large-scale collective migration, while higher adhesion leads to the formation of moving bands. Our study provides valuable insight into biological processes associated with collective cell motility.

  15. COLLECTIVE BARGAINING AGREEMENT BETWEEN NATIONAL SECURITY TECHNOLOGIES LLC (NSTEC)

    National Nuclear Security Administration (NNSA)

    COLLECTIVE BARGAINING AGREEMENT BETWEEN NATIONAL SECURITY TECHNOLOGIES LLC (NSTEC) AND LOCAL JOINT EXECUTIVE BOARD OF LAS VEGAS CULINARY WORKERS, LOCAL UNION NO. 226 OCTOBER 1, 2012 THROUGH SEPTEMBER 30, 2017 Page 1 of 38 TABLE OF CONTENTS ARTICLE PAGE PREAMBLE .............*....*...................*.......................................................................*.......................................*........*..*....... 3 1. UNION RECOGNITION

  16. Introduction: Opportunities in Large Data Collection and Analysis

    Energy Savers [EERE]

    Building America Opportunities in Large Data Collection and Analysis April 16, 2014 Moderator: Stacey Rothgeb - National Renewable Energy Laboratory Panelists: Omari Faakye - Steven Winter Associates, Inc. Noel Merket - National Renewable Energy Laboratory Chuck Booten - National Renewable Energy Laboratory Paul Norton - Norton Energy R & D Cheryn Metzger - National Renewable Energy Laboratory Stacey Rothgeb, Senior Engineer, National Renewable Energy Laboratory Stacey Rothgeb joined NREL

  17. Electrochemical thermodynamic measurement system

    DOE Patents [OSTI]

    Reynier, Yvan (Meylan, FR); Yazami, Rachid (Los Angeles, CA); Fultz, Brent T. (Pasadena, CA)

    2009-09-29

    The present invention provides systems and methods for accurately characterizing thermodynamic and materials properties of electrodes and electrochemical energy storage and conversion systems. Systems and methods of the present invention are configured for simultaneously collecting a suite of measurements characterizing a plurality of interconnected electrochemical and thermodynamic parameters relating to the electrode reaction state of advancement, voltage and temperature. Enhanced sensitivity provided by the present methods and systems combined with measurement conditions that reflect thermodynamically stabilized electrode conditions allow very accurate measurement of thermodynamic parameters, including state functions such as the Gibbs free energy, enthalpy and entropy of electrode/electrochemical cell reactions, that enable prediction of important performance attributes of electrode materials and electrochemical systems, such as the energy, power density, current rate and the cycle life of an electrochemical cell.

  18. State Geothermal Resource Assessment and Data Collection Efforts

    Broader source: Energy.gov [DOE]

    HawaiiNational Geothermal Data System Aids in Discovering Hawaii's Geothermal Resource (November 20, 2012)

  19. Programming Hybrid HPC Systems

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Programming Hybrid HPC Systems What is Old is New Again Viktor K. Decyk UCLA Abstract The next generation of supercomputers will likely consist of a hierarchy of parallel computers. If we can define each node as a parameterized abstract machine, then it is possible to design algorithms even if the actual hardware varies. Such an abstract machine can be defined to consist of a collection of vector (SIMD) processors, each with a small shared memory, communicating via a larger global memory. This

  20. Passive recovery of DNAPL from clayey soil via vertical collection wells

    SciTech Connect (OSTI)

    Tease, B.; Gagnon, D.

    1995-12-01

    A release of dense non-aqueous phase liquids (DNAPL) from two underground storage tanks (USTs), created a contaminant plume that extended approximately 30 feet into lacustrine sediments comprised mainly of varved clay. Subsurfaces investigations indicated that the release was comprised primarily of the chlorinated solvent Trichloroethene which had migrated horizontally approximately 250 feet cross-gradient to groundwater flow. A relatively narrow zone of free phase product extended from the UST area approximately 150-200 feet along the plume of migration at a depth of 20-30 feet below the ground surface. Since clay varves interconnected by vertical fractures is believed to have facilitated the DNAPL migration, 4{close_quotes} diameter stainless steel collection recovery of 10-20 quarts of DNAPL per each collection event, over a 4 month period supported what is believed to be preferential DNAPL migration. DNAPL recovery continued for a total of 6 months before the point of diminimus return (1-2 quarts/month) resulted in adopting a quarterly recovery schedule. To date, 201 quarts of free phase DNAPL have been recovered. DNAPL mobility, delineation, well installation and collection techniques are discussed. Compared to conventional remediation alternatives, this passive recovery system provides an innovative approach to a difficult and costly problem; recovery of DNAPL isolated within clay.

  1. High-density grids for efficient data collection from multiple crystals

    SciTech Connect (OSTI)

    Baxter, Elizabeth L.; Aguila, Laura; Alonso-Mori, Roberto; Barnes, Christopher O.; Bonagura, Christopher A.; Brehmer, Winnie; Brunger, Axel T.; Calero, Guillermo; Caradoc-Davies, Tom T.; Chatterjee, Ruchira; Degrado, William F.; Fraser, James S.; Ibrahim, Mohamed; Kern, Jan; Kobilka, Brian K.; Kruse, Andrew C.; Larsson, Karl M.; Lemke, Heinrik T.; Lyubimov, Artem Y.; Manglik, Aashish; McPhillips, Scott E.; Norgren, Erik; Pang, Siew S.; Soltis, S. M.; Song, Jinhu; Thomaston, Jessica; Tsai, Yingssu; Weis, William I.; Woldeyes, Rahel A.; Yachandra, Vittal; Yano, Junko; Zouni, Athina; Cohen, Aina E.

    2016-01-01

    Higher throughput methods to mount and collect data from multiple small and radiation-sensitive crystals are important to support challenging structural investigations using microfocus synchrotron beamlines. Furthermore, efficient sample-delivery methods are essential to carry out productive femtosecond crystallography experiments at X-ray free-electron laser (XFEL) sources such as the Linac Coherent Light Source (LCLS). To address these needs, a high-density sample grid useful as a scaffold for both crystal growth and diffraction data collection has been developed and utilized for efficient goniometer-based sample delivery at synchrotron and XFEL sources. A single grid contains 75 mounting ports and fits inside an SSRL cassette or uni-puck storage container. The use of grids with an SSRL cassette expands the cassette capacity up to 7200 samples. Grids may also be covered with a polymer film or sleeve for efficient room-temperature data collection from multiple samples. New automated routines have been incorporated into theBlu-Ice/DCSSexperimental control system to support grids, including semi-automated grid alignment, fully automated positioning of grid ports, rastering and automated data collection. Specialized tools have been developed to support crystallization experiments on grids, including a universal adaptor, which allows grids to be filled by commercial liquid-handling robots, as well as incubation chambers, which support vapor-diffusion and lipidic cubic phase crystallization experiments. Experiments in which crystals were loaded into grids or grown on grids using liquid-handling robots and incubation chambers are described. Crystals were screened at LCLS-XPP and SSRL BL12-2 at room temperature and cryogenic temperatures.

  2. High-density grids for efficient data collection from multiple crystals

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Baxter, Elizabeth L.; Aguila, Laura; Alonso-Mori, Roberto; Barnes, Christopher O.; Bonagura, Christopher A.; Brehmer, Winnie; Brunger, Axel T.; Calero, Guillermo; Caradoc-Davies, Tom T.; Chatterjee, Ruchira; et al

    2015-11-03

    Higher throughput methods to mount and collect data from multiple small and radiation-sensitive crystals are important to support challenging structural investigations using microfocus synchrotron beamlines. Furthermore, efficient sample-delivery methods are essential to carry out productive femtosecond crystallography experiments at X-ray free-electron laser (XFEL) sources such as the Linac Coherent Light Source (LCLS). To address these needs, a high-density sample grid useful as a scaffold for both crystal growth and diffraction data collection has been developed and utilized for efficient goniometer-based sample delivery at synchrotron and XFEL sources. A single grid contains 75 mounting ports and fits inside an SSRL cassettemore » or uni-puck storage container. The use of grids with an SSRL cassette expands the cassette capacity up to 7200 samples. Grids may also be covered with a polymer film or sleeve for efficient room-temperature data collection from multiple samples. New automated routines have been incorporated into theBlu-Ice/DCSSexperimental control system to support grids, including semi-automated grid alignment, fully automated positioning of grid ports, rastering and automated data collection. Specialized tools have been developed to support crystallization experiments on grids, including a universal adaptor, which allows grids to be filled by commercial liquid-handling robots, as well as incubation chambers, which support vapor-diffusion and lipidic cubic phase crystallization experiments. Experiments in which crystals were loaded into grids or grown on grids using liquid-handling robots and incubation chambers are described. As a result, crystals were screened at LCLS-XPP and SSRL BL12-2 at room temperature and cryogenic temperatures.« less

  3. Cooling water distribution system

    DOE Patents [OSTI]

    Orr, Richard

    1994-01-01

    A passive containment cooling system for a nuclear reactor containment vessel. Disclosed is a cooling water distribution system for introducing cooling water by gravity uniformly over the outer surface of a steel containment vessel using an interconnected series of radial guide elements, a plurality of circumferential collector elements and collector boxes to collect and feed the cooling water into distribution channels extending along the curved surface of the steel containment vessel. The cooling water is uniformly distributed over the curved surface by a plurality of weirs in the distribution channels.

  4. Control of the positional relationship between a sample collection instrument and a surface to be analyzed during a sampling procedure using a laser sensor

    DOE Patents [OSTI]

    Van Berkel, Gary J. (Clinton, TN); Kertesz, Vilmos (Knoxville, TN)

    2012-02-21

    A system and method utilizes distance-measuring equipment including a laser sensor for controlling the collection instrument-to-surface distance during a sample collection process for use, for example, with mass spectrometric detection. The laser sensor is arranged in a fixed positional relationship with the collection instrument, and a signal is generated by way of the laser sensor which corresponds to the actual distance between the laser sensor and the surface. The actual distance between the laser sensor and the surface is compared to a target distance between the laser sensor and the surface when the collection instrument is arranged at a desired distance from the surface for sample collecting purposes, and adjustments are made, if necessary, so that the actual distance approaches the target distance.

  5. Collecting and recirculating condensate in a nuclear reactor containment

    DOE Patents [OSTI]

    Schultz, T.L.

    1993-10-19

    An arrangement passively cools a nuclear reactor in the event of an emergency, condensing and recycling vaporized cooling water. The reactor is surrounded by a containment structure and has a storage tank for cooling liquid, such as water, vented to the containment structure by a port. The storage tank preferably is located inside the containment structure and is thermally coupleable to the reactor, e.g. by a heat exchanger, such that water in the storage tank is boiled off to carry away heat energy. The water is released as a vapor (steam) and condenses on the cooler interior surfaces of the containment structure. The condensed water flows downwardly due to gravity and is collected and routed back to the storage tank. One or more gutters are disposed along the interior wall of the containment structure for collecting the condensate from the wall. Piping is provided for communicating the condensate from the gutters to the storage tank. 3 figures.

  6. Collecting and recirculating condensate in a nuclear reactor containment

    DOE Patents [OSTI]

    Schultz, Terry L. (Murrysville Boro, PA)

    1993-01-01

    An arrangement passively cools a nuclear reactor in the event of an emergency, condensing and recycling vaporized cooling water. The reactor is surrounded by a containment structure and has a storage tank for cooling liquid, such as water, vented to the containment structure by a port. The storage tank preferably is located inside the containment structure and is thermally coupleable to the reactor, e.g. by a heat exchanger, such that water in the storage tank is boiled off to carry away heat energy. The water is released as a vapor (steam) and condenses on the cooler interior surfaces of the containment structure. The condensed water flows downwardly due to gravity and is collected and routed back to the storage tank. One or more gutters are disposed along the interior wall of the containment structure for collecting the condensate from the wall. Piping is provided for communicating the condensate from the gutters to the storage tank.

  7. Collection of liquid from below-ground location

    DOE Patents [OSTI]

    Phillips, S.J.; Alexander, R.G.

    1995-05-30

    A method is described for retrieving liquid from a below-ground collection area by permitting gravity flow of the liquid from the collection area to a first closed container; monitoring the level of the liquid in the closed container; and after the liquid reaches a given level in the first closed container, transferring the liquid to a second closed container disposed at a location above the first closed container, via a conduit, by introducing into the first closed container a gas which is substantially chemically inert with respect to the liquid, the gas being at a pressure sufficient to propel the liquid from the first closed container to the second closed container. 3 figs.

  8. Collective aspects of protein folding illustrated by a toy model

    SciTech Connect (OSTI)

    Stillinger, F.H. [AT& T Bell Laboratories, Murray Hill, New Jersey 07974 (United States)] [AT& T Bell Laboratories, Murray Hill, New Jersey 07974 (United States); Head-Gordon, T. [Life Sciences Division, Lawrence Berkeley Laboratory, University of California, Berkeley, California 94720 (United States)] [Life Sciences Division, Lawrence Berkeley Laboratory, University of California, Berkeley, California 94720 (United States)

    1995-09-01

    A simple toy model for polypeptides serves as a testbed to illuminate some nonlocal, or collective, aspects of protein folding phenomena. The model is two dimensional and has only two amino acids, but involves a continuous range of backbone bend angles. Global potential energy minima and their folding structures have been determined for leading members of two special and contrasting polypeptide sequences, center doped and Fibonacci, named descriptively for their primary structures. The results display the presence of spontaneous symmetry breaking, elastic strain, and substantial conformational variation for specific embedded amino acid strings. We conclude that collective variables generated by the primary amino acid structure may be required for fully effective protein folding predictors, including those based on neural networks.

  9. Impedances and collective instabilities of the Tevatron at Run II

    SciTech Connect (OSTI)

    Ng, King-Yuen, FERMI

    1998-09-01

    The longitudinal and transverse coupling impedances of the Tevatron vacuum chamber are estimated and summed up. The resistive-wall impedances of the beam pipe and the laminations in the Lambertson magnets dominate below {approximately} 50 MHz. Then come the inductive parts of the bellows and BPM`s. The longitudinal and transverse collective instabilities, for both single bunch and multi bunches, are studied using Run II parameters. As expected the transverse coupled-bunch instability driven by the resistive-wall impedance is the most severe collective instability. However, it can be damped by a transverse damper designed for the correction of injection offsets. The power of such a damper has been studied.

  10. Electrodeposited cobalt sulfide hole collecting layer for polymer solar cells

    SciTech Connect (OSTI)

    Zampetti, Andrea; De Rossi, Francesca; Brunetti, Francesca; Reale, Andrea; Di Carlo, Aldo; Brown, Thomas M., E-mail: thomas.brown@uniroma2.it [CHOSE (Centre for Hybrid and Organic Solar Energy), Department of Electronic Engineering, University of Rome Tor Vergata, Via del Politecnico 1, 00133 Rome (Italy)

    2014-08-11

    In polymer solar cells based on the blend of regioregular poly(3-hexylthiophene) (P3HT) and phenyl-C61-butyric acid methyl ester, the hole collecting layer has to be endowed with its ionization potential close to or greater than that of P3HT (?5?eV). Conductive polymer blends such as poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) and metal oxides such as vanadium pentoxide (V{sub 2}O{sub 5}) and molybdenum trioxide (MoO{sub 3}) satisfy this requirement and have been the most common materials used so far in bulk heterojunction structures. We report here cobalt sulfide (CoS) to be a promising hole collecting material deposited by convenient and room temperature electrodeposition. By simply tuning the CoS electrodeposition parameters, power conversion efficiencies similar (within 15%) to a reference structure with PEDOT:PSS were obtained.

  11. Mobile Data Collection Applications: A Proof of Concept

    SciTech Connect (OSTI)

    Chang, J

    2006-09-20

    This project's goal is to provide a proof of concept for mobile data collection applications, and identify the best ways such applications could be implemented and used. Such an application should decrease the time and resources users now need to devote to redundant data processes, and provide an easy of locating and retrieving data at a later time. The two types of available mobile devices, Personal Digital Assistants and Tablet Personal Computers, each have their particular strengths that suggest themselves for certain types of applications. As such, parallel data collection applications have been developed, with a common web application for uploading information to the database. While these aspects have been developed and proven, it still remains to refine these applications, develop the tables to hold their data, and field-test with users for their feedback.

  12. Physics of collisions between ultrarelativistic nuclei: Manifestation of collective effects

    SciTech Connect (OSTI)

    Korotkikh, V. L.

    2009-11-15

    Experimental results concerning heavy-ion collisions studied by means of the Relativistic Heavy-Ion Collider (RHIC) at an energy of 100 GeV per nucleon and showing manifestations of collective effects are surveyed. These effects are interpreted as a consequence of the formation of a dense thermalized medium referred to as quark-gluon plasma (strongly interacting quark-gluon plasma, quark-gluon matter, parton medium). An azimuthal anisotropy of particles, the suppression of the particle yield at high transverse momenta in relation to proton-proton collisions, and a change in the shape of the peak from a hadron jet in nucleus-nucleus collisions are spectacular manifestations of collective effects.

  13. Optimal Heat Collection Element Shapes for Parabolic Trough Concentrators

    SciTech Connect (OSTI)

    Bennett, C

    2007-11-15

    For nearly 150 years, the cross section of the heat collection tubes used at the focus of parabolic trough solar concentrators has been circular. This type of tube is obviously simple and easily fabricated, but it is not optimal. It is shown in this article that the optimal shape, assuming a perfect parabolic figure for the concentrating mirror, is instead oblong, and is approximately given by a pair of facing parabolic segments.

  14. Coordinated garbage collection for raid array of solid state disks

    DOE Patents [OSTI]

    Dillow, David A; Ki, Youngjae; Oral, Hakki S; Shipman, Galen M; Wang, Feiyi

    2014-04-29

    An optimized redundant array of solid state devices may include an array of one or more optimized solid-state devices and a controller coupled to the solid-state devices for managing the solid-state devices. The controller may be configured to globally coordinate the garbage collection activities of each of said optimized solid-state devices, for instance, to minimize the degraded performance time and increase the optimal performance time of the entire array of devices.

  15. Radial electron collection in dye-sensitized solar cells.

    SciTech Connect (OSTI)

    Martinson, A. B. B.; Elam, J. W.; Liu, J.; Pellin, M. J.; Marks, T. J.; Hupp, J. T.; Materials Science Division; Northwestern Univ.

    2008-01-01

    We introduce a new photoelectrode architecture consisting of concentric conducting and semiconducting nanotubes for use in dye-sensitized solar cells (DSSCs). Atomic layer deposition is employed to grow indium tin oxide (ITO) within a porous template and subsequently coat the high area photoelectrode with amorphous TiO2. Compared with control devices lacking a current collector within the pores, the new photoelectrode geometry exhibits dramatically higher current densities, an effect attributed to the radial collection of electrons.

  16. SLAC Large Detector (SLD) Image and Event Display Collections

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Perl, Joseph; Cowan, Ray; Johnson, Tony

    The SLD makes use of the unique capabilities of the Stanford Linear Collider (SLC) to perform studies of polarized Z particles produced in collisions between electrons and positrons. The SLD Event Display Collection shows computer generated pictures of a number of Z particle decays as reconstructed by the SLD detector. More than 90 images, each in several formats, captured from 1991 - 1996 events, are archived here. There are also figures and data plots available.

  17. Laboratory employees collect backpacks, school supplies for area school

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    children School supplies for children Laboratory employees collect backpacks, school supplies for area school children Employees donated more than 1,000 backpacks and thousands of school supplies, including pencils, pens, and notebooks. August 20, 2010 Los Alamos National Laboratory sits on top of a once-remote mesa in northern New Mexico with the Jemez mountains as a backdrop to research and innovation covering multi-disciplines from bioscience, sustainable energy sources, to plasma physics

  18. Interactive Uses of the NSDL: .Atmospheric Visualization Collection

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Interactive Uses of the NSDL: Atmospheric Visualization Collection C. M. Klaus, E. N. Vernon, T. McCollum, T. R. Gobble, H. M. Anthony, and D. Johnson Argonne National Laboratory Argonne, Illinois K. Andrew Eastern Illinois University Charleston, Illinois G. G. Mace University of Utah Salt Lake City, Utah C. P. Bahrmann University of Oklahoma Norman, Oklahoma User Interfaces The National Science Digital Library (NSDL) has three user interfaces for accessing data images. 1. The Geophysical Focus

  19. Apparatus and process for collection of gas and vapor samples

    DOE Patents [OSTI]

    Jackson, Dennis G. (Augusta, GA); Peterson, Kurt D. (Aiken, SC); Riha, Brian D. (Augusta, GA)

    2008-04-01

    A gas sampling apparatus and process is provided in which a standard crimping tool is modified by an attached collar. The collar permits operation of the crimping tool while also facilitating the introduction of a supply of gas to be introduced into a storage vial. The introduced gas supply is used to purge ambient air from a collection chamber and an interior of the sample vial. Upon completion of the purging operation, the vial is sealed using the crimping tool.

  20. Building America Webinar: Opportunities in Large Data Collection and

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Analysis-Presentation #1 | Department of Energy 1 Building America Webinar: Opportunities in Large Data Collection and Analysis-Presentation #1 This presentation is titled Multifamily Envelope Leakage Model and is included in the webinar on April 16, 2014. PDF icon BA_Webinar_ Faakye _4-16-14.pdf More Documents & Publications Building America Webinar: Multifamily Ventilation Strategies and Compartmentalization Requirements - Sean Maxwell Building America Webinar: High Performance

  1. Pantex collects food for kids | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    collects food for kids | National Nuclear Security Administration Facebook Twitter Youtube Flickr RSS People Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response Recapitalizing Our Infrastructure Countering Nuclear Terrorism About Our Programs Our History Who We Are Our Leadership Our Locations Budget Our Operations Library Bios Congressional Testimony Fact Sheets Newsletters Press Releases Photo Gallery Jobs Apply for Our Jobs Our Jobs Working at

  2. Indoor Temperature and Humidity Data Collection and Analysis

    Energy Savers [EERE]

    NREL is a national laboratory of the U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, operated by the Alliance for Sustainable Energy, LLC. Indoor Temperature and Humidity Data Collection and Analysis Chuck Booten, NREL Paul Norton, NERD Cheryn Metzger, NREL Why do we care about indoor Temp/RH? "Anecdotal evidence from the field and controlled studies have raised concerns about the accuracy of software-based energy analysis for existing homes. ....

  3. Steam System Modeler | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Steam System Modeler Steam System Modeler April 17, 2014 - 11:34am Addthis There is often flexibility in the operational conditions and requirements of any steam system. In order to optimize performance, the impacts of potential adjustments need to be understood individually and collectively. The Steam System Modeler allows you to create up to a 3-pressure-header basic model of your current steam system. A second model can then be created by adjusting a series of characteristics simulating

  4. Comparison of Particulate Collection in Probes and on Filters

    SciTech Connect (OSTI)

    Eaton, J.M.; Humphreys, M.P.

    2001-06-14

    Major radionuclide emissions from the Department of Energy's Y-12 National Security Complex are nuclides of uranium which are emitted as a particulate. The radionuclide NESHAP regulation requires stack sampling to be conducted in accordance with ANST Standard N13.1, 1969. Appendix B of this standard requires in every case where sampling delivery lines are used that an evaluation should be made of deposition in these lines. A number of Y-12 Complex stacks are fitted with continuous samplers which draw particulate laden air through a probe and across a sample filter. One approach to evaluate line loss as required by the ANSI standard is to establish a representative factor that is used for all subsequent sampling efforts. Another approach is to conduct a routine probe wash procedure on an ongoing basis to account for line losses. In 1991, Y-12 National Security Complex personnel began routine probe washes as part of their sample collection procedure. Since then, 50-80 stacks have been sampled on a near continuous basis and probe washes have been conducted quarterly. Particulate collection in probes versus particulate collection on filters is recorded as a probe factor and probe factor trends for a 10-year period are available.

  5. H2 Refuel H-Prize Technical Data Collection Requirements | Department...

    Broader source: Energy.gov (indexed) [DOE]

    Technical Data Collection Requirements" held on May 14, 2015. PDF icon H2 Refuel H-Prize Technical Data Collection Requirements Webinar Slides More Documents & Publications H2 ...

  6. UTEX The Culture Collection of Algae at The University of Texas...

    Open Energy Info (EERE)

    UTEX The Culture Collection of Algae at The University of Texas at Austin Jump to: navigation, search Name: University of Texas at Austin The Culture Collection of Algae...

  7. Secondary fuel delivery system

    DOE Patents [OSTI]

    Parker, David M. (Oviedo, FL); Cai, Weidong (Oviedo, FL); Garan, Daniel W. (Orlando, FL); Harris, Arthur J. (Orlando, FL)

    2010-02-23

    A secondary fuel delivery system for delivering a secondary stream of fuel and/or diluent to a secondary combustion zone located in the transition piece of a combustion engine, downstream of the engine primary combustion region is disclosed. The system includes a manifold formed integral to, and surrounding a portion of, the transition piece, a manifold inlet port, and a collection of injection nozzles. A flowsleeve augments fuel/diluent flow velocity and improves the system cooling effectiveness. Passive cooling elements, including effusion cooling holes located within the transition boundary and thermal-stress-dissipating gaps that resist thermal stress accumulation, provide supplemental heat dissipation in key areas. The system delivers a secondary fuel/diluent mixture to a secondary combustion zone located along the length of the transition piece, while reducing the impact of elevated vibration levels found within the transition piece and avoiding the heat dissipation difficulties often associated with traditional vibration reduction methods.

  8. Automated imaging system for single molecules

    DOE Patents [OSTI]

    Schwartz, David Charles; Runnheim, Rodney; Forrest, Daniel

    2012-09-18

    There is provided a high throughput automated single molecule image collection and processing system that requires minimal initial user input. The unique features embodied in the present disclosure allow automated collection and initial processing of optical images of single molecules and their assemblies. Correct focus may be automatically maintained while images are collected. Uneven illumination in fluorescence microscopy is accounted for, and an overall robust imaging operation is provided yielding individual images prepared for further processing in external systems. Embodiments described herein are useful in studies of any macromolecules such as DNA, RNA, peptides and proteins. The automated image collection and processing system and method of same may be implemented and deployed over a computer network, and may be ergonomically optimized to facilitate user interaction.

  9. Beryllium-Associated Worker Registry Data Collection and Management Guidance

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    87-2007 June 2007 DOE TECHNICAL STANDARD Beryllium-Associated Worker Registry Data Collection and Management Guidance U.S. Department of Energy AREA SAFT Washington, D.C. 20585 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited NOT MEASUREMENT SENSITIVE DOE-STD-1187-2007 ii Available on the Department of Energy Technical Standards Program Web site at http://www.hss.energy.gov/NuclearSafety/techstds/ DOE-STD-1187-2007 iii FOREWORD 1. This standard provides acceptable

  10. New sensor array changes the data collection game | Argonne National...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    From climate studies to understanding the dynamics of particular types of air pollution to identifying trends in noise or increases in pedestrian traffic-the Waggle system...

  11. Concentrating Solar Power: Best Practices Handbook for the Collection and Use of Solar Resource Data (CSP)

    SciTech Connect (OSTI)

    Stoffel, T.; Renne, D.; Myers, D.; Wilcox, S.; Sengupta, M.; George, R.; Turchi, C.

    2010-09-01

    As the world looks for low-carbon sources of energy, solar power stands out as the most abundant energy resource. Harnessing this energy is the challenge for this century. Photovoltaics and concentrating solar power (CSP) are two primary forms of electricity generation using sunlight. These use different technologies, collect different fractions of the solar resource, and have different siting and production capabilities. Although PV systems are most often deployed as distributed generation sources, CSP systems favor large, centrally located systems. Accordingly, large CSP systems require a substantial investment, sometimes exceeding $1 billion in construction costs. Before such a project is undertaken, the best possible information about the quality and reliability of the fuel source must be made available. That is, project developers need to have reliable data about the solar resource available at specific locations to predict the daily and annual performance of a proposed CSP plant. Without these data, no financial analysis is possible. This handbook presents detailed information about solar resource data and the resulting data products needed for each stage of the project.

  12. Collective Effects in a Diffraction Limited Storage Ring

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Nagaoka, Ryutaro; Bane, Karl L.F.

    2015-10-20

    Our paper gives an overview of collective effects that are likely to appear and possibly limit the performance in a diffraction-limited storage ring (DLSR) that stores a high-intensity ultra-low-emittance beam. Beam instabilities and other intensity-dependent effects that may significantly impact the machine performance are covered. The latter include beam-induced machine heating, Touschek scattering, intra-beam scattering, as well as incoherent tune shifts. The general trend that the efforts to achieve ultra-low emittance result in increasing the machine coupling impedance and the beam sensitivity to instability is reviewed. The nature of coupling impedance in a DLSR is described, followed by a seriesmore » of potentially dangerous beam instabilities driven by the former, such as resistive-wall, TMCI (transverse mode coupling instability), head-tail and microwave instabilities. Additionally, beam-ion and CSR (coherent synchrotron radiation) instabilities are also treated. Means to fight against collective effects such as lengthening of the bunch with passive harmonic cavities and bunch-by-bunch transverse feedback are introduced. Numerical codes developed and used to evaluate the machine coupling impedance, as well as to simulate beam instability using the former as inputs are described.« less

  13. Alpha-beta coordination method for collective search

    DOE Patents [OSTI]

    Goldsmith, Steven Y. (Albuquerque, NM)

    2002-01-01

    The present invention comprises a decentralized coordination strategy called alpha-beta coordination. The alpha-beta coordination strategy is a family of collective search methods that allow teams of communicating agents to implicitly coordinate their search activities through a division of labor based on self-selected roles and self-determined status. An agent can play one of two complementary roles. An agent in the alpha role is motivated to improve its status by exploring new regions of the search space. An agent in the beta role is also motivated to improve its status, but is conservative and tends to remain aggregated with other agents until alpha agents have clearly identified and communicated better regions of the search space. An agent can select its role dynamically based on its current status value relative to the status values of neighboring team members. Status can be determined by a function of the agent's sensor readings, and can generally be a measurement of source intensity at the agent's current location. An agent's decision cycle can comprise three sequential decision rules: (1) selection of a current role based on the evaluation of the current status data, (2) selection of a specific subset of the current data, and (3) determination of the next heading using the selected data. Variations of the decision rules produce different versions of alpha and beta behaviors that lead to different collective behavior properties.

  14. Collective mode evidence of high-spin bosonization in a trapped one-dimensional atomic Fermi gas with tunable spin

    SciTech Connect (OSTI)

    Liu, Xia-Ji Hu, Hui

    2014-11-15

    We calculate the frequency of collective modes of a one-dimensional repulsively interacting Fermi gas with high-spin symmetry confined in harmonic traps at zero temperature. This is a system realizable with fermionic alkaline-earth-metal atoms such as {sup 173}Yb, which displays an exact SU(?) spin symmetry with ??2 and behaves like a spinless interacting Bose gas in the limit of infinite spin components ???, namely high-spin bosonization. We solve the homogeneous equation of state of the high-spin Fermi system by using Bethe ansatz technique and obtain the density distribution in harmonic traps based on local density approximation. The frequency of collective modes is calculated by exactly solving the zero-temperature hydrodynamic equation. In the limit of large number of spin-components, we show that the mode frequency of the system approaches that of a one-dimensional spinless interacting Bose gas, as a result of high-spin bosonization. Our prediction of collective modes is in excellent agreement with a very recent measurement for a Fermi gas of {sup 173}Yb atoms with tunable spin confined in a two-dimensional tight optical lattice.

  15. Heterogeneous ice nucleation and water uptake by field-collected atmospheric particles below 273 K

    SciTech Connect (OSTI)

    Wang, Bingbing; Laskin, Alexander; Roedel, Tobias R.; Gilles, Marry K.; Moffet, Ryan C.; Tivanski, Alexei V.; Knopf, Daniel A.

    2012-09-25

    Atmospheric ice formation induced by particles with complex chemical and physical properties through heterogeneous nucleation is not well understood. Heterogeneous ice nucleation and water uptake by ambient particles collected from urban environments in Los Angeles and Mexico City are presented. Using a vapour controlled cooling system equipped with an optical microscopy, the range of onset conditions for ice nucleation and water uptake by the collected particles was determined as a function of temperature (200{273 K) and relative humidity with respect to ice (RHice) up to water saturation. Three distinctly different types of authentic atmospheric particles were investigated including soot particles associated with organics/inorganics, inorganic particles of marine origin coated with organic material, and Pb/Zn containing inorganic particles apportioned to anthropogenic emissions relevant to waste incineration. Single particle characterization was provided by micro-spectroscopic analyses using computer controlled scanning electron microscopy with energy dispersive analysis of X-rays (CCSEM/EDX) and scanning transmission X-ray microscopy with near edge X-ray absorption ne structure spectroscopy (STXM/NEXAFS). Above 230 K, signicant differences in water uptake and immersion freezing effciencies of the different particle types were observed. Below 230 K, the particles exhibited high deposition ice nucleation effciencies and formed ice at RHice values well below homogeneous ice nucleation limits. The data show that the chemical composition of these eld{collected particles plays an important role in determining water uptake and immersion freezing. Heterogeneous ice nucleation rate coeffcients, cumulative ice nuclei (IN) spectrum, and IN activated fraction for deposition ice nucleation are derived. The presented ice nucleation data demonstrate that anthropogenic and marine particles comprising of various chemical and physical properties exhibit distinctly different ice nucleation effciencies and can serve as effcient IN at atmospheric conditions typical for cirrus and mixed phase clouds. This indicates a potential link between human activities and cloud formation, and thus climate.

  16. Consideration of liners and covers in performance assessments

    SciTech Connect (OSTI)

    Phifer, Mark A.; Seitz, Robert R.; Suttora, Linda C.

    2014-09-18

    On-site disposal cells are in use and being considered at several United States Department of Energy (USDOE) sites as the final disposition for large amounts of waste associated with cleanup of contaminated areas and facilities. These disposal cells are typically regulated by States and/or the U.S. Environmental Protection Agency under the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) in addition to having to comply with requirements in DOE Order 435.1, Radioactive Waste Management due to the radioactive waste. The USDOE-Environmental Management Office of Site Restoration formed a working group to foster improved communication and sharing of information for personnel associated with these CERCLA disposal cells and work towards more consistent assumptions, as appropriate, for technical and policy considerations related to CERCLA risk assessments and DOE Order 435.1 performance assessments in support of a Record of Decision and Disposal Authorization Statement, respectively. One of the issues considered by the working group, which is addressed in this report, was how to appropriately consider the performance of covers and liners/leachate collections systems in the context of a DOE Order 435.1 performance assessment (PA). This same information may be appropriate for consideration within CERCLA risk assessments for these facilities. These OSDCs are generally developed to meet hazardous waste (HW) disposal design standards under the Resource Conservation and Recovery Act (RCRA) as well as the DOE Order 435.1 performance based standards for disposal of radioactive waste. To meet the standards for HW, the facilities typically include engineered covers and liner/leachate collection systems. Thus, when considering such facilities in the context of a DOE Order 435.1 PA, there is a need to address the evolution of performance of covers and liner/leachate collection systems in the context of meeting a performance standard considering time frames of 1,000 years for compliance and potentially thousands of years based on the wastes to test the robustness of the system. Experience has shown that there are a range of expectations and perspectives from the different regulators involved at different sites when reviewing assumptions related to cover and liner/leachate collection system performance. However for HW disposal alone under RCRA the design standards are typically considered sufficient by the regulators without a requirement to assess long-term performance thus avoiding the need to consider the details addressed in this report. This report provides suggestions for a general approach to address covers and liners/leachate collection systems in a DOE Order 435.1 PA and how to integrate assessments with defense-in-depth considerations such as design, operations, and waste acceptance criteria to address uncertainties. The emphasis is on water balances and management in such assessments. Specific information and references are provided for details needed to address the evolution of individual components of cover and liner/leachate collection systems. This information was then synthesized into suggestions for best practices for cover and liner system design and examples of approaches to address the performance of covers and liners as part of a performance assessment of the disposal system. Numerous references are provided for sources of information to help describe the basis for performance of individual components of cover and liner systems.

  17. Embedding global barrier and collective in torus network with each node combining input from receivers according to class map for output to senders

    DOE Patents [OSTI]

    Chen, Dong; Coteus, Paul W; Eisley, Noel A; Gara, Alan; Heidelberger, Philip; Senger, Robert M; Salapura, Valentina; Steinmacher-Burow, Burkhard; Sugawara, Yutaka; Takken, Todd E

    2013-08-27

    Embodiments of the invention provide a method, system and computer program product for embedding a global barrier and global interrupt network in a parallel computer system organized as a torus network. The computer system includes a multitude of nodes. In one embodiment, the method comprises taking inputs from a set of receivers of the nodes, dividing the inputs from the receivers into a plurality of classes, combining the inputs of each of the classes to obtain a result, and sending said result to a set of senders of the nodes. Embodiments of the invention provide a method, system and computer program product for embedding a collective network in a parallel computer system organized as a torus network. In one embodiment, the method comprises adding to a torus network a central collective logic to route messages among at least a group of nodes in a tree structure.

  18. Regularities and symmetries of subsets of collective 0{sup +} states

    SciTech Connect (OSTI)

    Bonatsos, Dennis; McCutchan, E. A.; Casten, R. F.; Casperson, R. J.; Werner, V.; Williams, E.

    2009-09-15

    The energies of subsets of excited 0{sup +} states in geometric collective models are investigated and found to exhibit intriguing regularities. In models with an infinite square well potential, it is found that a single formula, dependent on only the number of dimensions, describes a subset of 0{sup +} states. The same behavior of a subset of 0{sup +} states is seen in the large boson number limit of the interacting boson approximation (IBA) model near the critical point of a first-order phase transition, in contrast to the fact that these 0{sup +} state energies exhibit a harmonic behavior in all three limiting symmetries of the IBA. Finally, the observed regularities in 0{sup +} energies are analyzed in terms of the underlying group theoretical framework of the different models.

  19. Regularities and symmetries of subsets of collective 0{sup+} states.

    SciTech Connect (OSTI)

    Bonatsos, D.; McCutchan, E. A.; Casten, R. F.; Casperson, R. J.; Werner, V.; Williams, E.; Physics; N.C.S.R.; Yale Univ.

    2009-09-01

    The energies of subsets of excited 0{sup +} states in geometric collective models are investigated and found to exhibit intriguing regularities. In models with an infinite square well potential, it is found that a single formula, dependent on only the number of dimensions, describes a subset of 0{sup +} states. The same behavior of a subset of 0{sup +} states is seen in the large boson number limit of the interacting boson approximation (IBA) model near the critical point of a first-order phase transition, in contrast to the fact that these 0{sup +} state energies exhibit a harmonic behavior in all three limiting symmetries of the IBA. Finally, the observed regularities in 0{sup +} energies are analyzed in terms of the underlying group theoretical framework of the different models.

  20. Regularities and symmetries of collective 0{sup+} states.

    SciTech Connect (OSTI)

    Bonatsos, D.; McCutchan, E. A.; Casten, R. F.; Casperson, R. J.; Werner, V.; Williams, E.; Physics; N.C.S.R.

    2009-01-01

    The energies of subsets of excited 0{sup +} states in geometric collective models are investigated and found to exhibit intriguing regularities. In models with an infinite square well potential, it is found that a single formula, dependent on only the number of dimensions, describes a subset of 0{sup +} states. The same behavior of a subset of 0{sup +} states is seen in the large boson number limit of the interacting boson approximation (IBA) model near the critical point of a first-order phase transition, in contrast to the fact that these 0{sup +} state energies exhibit a harmonic behavior in all three limiting symmetries of the IBA. Finally, the observed regularities in 0{sup +} energies are analyzed in terms of the underlying group theoretical framework of the different models.

  1. The data collection component of the Hanford Meteorology Monitoring Program

    SciTech Connect (OSTI)

    Glantz, C.S.; Islam, M.M.

    1988-09-01

    An intensive program of meteorological monitoring is in place at the US Department of Energy's Hanford Site. The Hanford Meteorology Monitoring Program involves the measurement, observation, and storage of various meteorological data; continuous monitoring of regional weather conditions by a staff of professional meteorologists; and around-the-clock forecasting of weather conditions for the Hanford Site. The objective of this report is to document the data collection component of the program. In this report, each meteorological monitoring site is discussed in detail. Each site's location and instrumentation are described and photographs are presented. The methods for processing and communicating data to the Hanford Meteorology Station are also discussed. Finally, the procedures followed to maintain and calibrate these instruments are presented. 2 refs., 83 figs., 15 tabs.

  2. Collective alignment of polar filaments by molecular motors.

    SciTech Connect (OSTI)

    Ziebert, F.; Aranson, I. S.; Vershinin, M.; Gross, S. P.; Materials Science Division; Univ. of California at Irvine

    2009-04-01

    We study the alignment of polar biofilaments, such as microtubules and actin, subject to the action of multiple molecular motors attached simultaneously to more than one filament. Focusing on a paradigm model of only two filaments interacting with multiple motors, we were able to investigate in detail the alignment dynamics. While almost no alignment occurs in the case of a single motor, the filaments become rapidly aligned due to the collective action of the motors. Our analysis shows that the alignment time is governed by the number of bound motors and the magnitude of the motors stepping fluctuations. We predict that the time scale of alignment is in the order of seconds, much faster than that reported for passive crosslink-induced bundling. In vitro experiments on the alignment of microtubules by multiple-motor covered beads are in qualitative agreement. We also discuss another mode of fast alignment of filaments, namely the cooperation between motors and passive crosslinks.

  3. Optimized collectives using a DMA on a parallel computer

    DOE Patents [OSTI]

    Chen, Dong; Gabor, Dozsa; Giampapa, Mark E.; Heidelberger; Phillip

    2011-02-08

    Optimizing collective operations using direct memory access controller on a parallel computer, in one aspect, may comprise establishing a byte counter associated with a direct memory access controller for each submessage in a message. The byte counter includes at least a base address of memory and a byte count associated with a submessage. A byte counter associated with a submessage is monitored to determine whether at least a block of data of the submessage has been received. The block of data has a predetermined size, for example, a number of bytes. The block is processed when the block has been fully received, for example, when the byte count indicates all bytes of the block have been received. The monitoring and processing may continue for all blocks in all submessages in the message.

  4. Collective accelerator using field-reversed plasma rings

    SciTech Connect (OSTI)

    Hartman, C.W.

    1981-09-19

    This note discusses the possibility of magnetically accelerating the plasma rings. At low-to-moderate ring kinetic energy, application to heating, fueling, and efficient current drive of conventional fusion reactors appears possible. At high ring kinetic energy, applications to inertial-confinement fusion through pellet heating and to transuranic element synthesis appear possible. The rings may be considered to be a self-linking flux bundle having net helicity. From an accelerator point of view, the rings represent collective particle entities held together by magnetic forces and may be viewed as macroparticles or micropellets having large magnetic moment per unit mass. Because of the relatively long lifetime and resiliency of the rings, it appears possible to accelerate to multimegajoule kinetic energy over reasonable distances and to focus the rings to centimeter-size dimensions.

  5. Device for collecting chemical compounds and related methods

    DOE Patents [OSTI]

    Scott, Jill R.; Groenewold, Gary S.; Rae, Catherine

    2013-01-01

    A device for sampling chemical compounds from fixed surfaces and related methods are disclosed. The device may include a vacuum source, a chamber and a sorbent material. The device may utilize vacuum extraction to volatilize the chemical compounds from the fixed surfaces so that they may be sorbed by the sorbent material. The sorbent material may then be analyzed using conventional thermal desorption/gas chromatography/mass spectrometry (TD/GC/MS) instrumentation to determine presence of the chemical compounds. The methods may include detecting release and presence of one or more chemical compounds and determining the efficacy of decontamination. The device may be useful in collection and analysis of a variety of chemical compounds, such as residual chemical warfare agents, chemical attribution signatures and toxic industrial chemicals.

  6. Efficient parallel global garbage collection on massively parallel computers

    SciTech Connect (OSTI)

    Kamada, Tomio; Matsuoka, Satoshi; Yonezawa, Akinori

    1994-12-31

    On distributed-memory high-performance MPPs where processors are interconnected by an asynchronous network, efficient Garbage Collection (GC) becomes difficult due to inter-node references and references within pending, unprocessed messages. The parallel global GC algorithm (1) takes advantage of reference locality, (2) efficiently traverses references over nodes, (3) admits minimum pause time of ongoing computations, and (4) has been shown to scale up to 1024 node MPPs. The algorithm employs a global weight counting scheme to substantially reduce message traffic. The two methods for confirming the arrival of pending messages are used: one counts numbers of messages and the other uses network `bulldozing.` Performance evaluation in actual implementations on a multicomputer with 32-1024 nodes, Fujitsu AP1000, reveals various favorable properties of the algorithm.

  7. Coordinating Garbage Collection for Arrays of Solid-state Drives

    SciTech Connect (OSTI)

    Kim, Youngjae; Lee, Junghee; Oral, H Sarp; Dillow, David A; Wang, Feiyi; Shipman, Galen M

    2014-01-01

    Although solid-state drives (SSDs) offer significant performance improvements over hard disk drives (HDDs) for a number of workloads, they can exhibit substantial variance in request latency and throughput as a result of garbage collection (GC). When GC conflicts with an I/O stream, the stream can make no forward progress until the GC cycle completes. GC cycles are scheduled by logic internal to the SSD based on several factors such as the pattern, frequency, and volume of write requests. When SSDs are used in a RAID with currently available technology, the lack of coordination of the SSD-local GC cycles amplifies this performance variance. We propose a global garbage collection (GGC) mechanism to improve response times and reduce performance variability for a RAID of SSDs. We include a high-level design of SSD-aware RAID controller and GGC-capable SSD devices and algorithms to coordinate the GGC cycles. We develop reactive and proactive GC coordination algorithms and evaluate their I/O performance and block erase counts for various workloads. Our simulations show that GC coordination by a reactive scheme improves average response time and reduces performance variability for a wide variety of enterprise workloads. For bursty, write-dominated workloads, response time was improved by 69% and performance variability was reduced by 71%. We show that a proactive GC coordination algorithm can further improve the I/O response times by up to 9% and the performance variability by up to 15%. We also observe that it could increase the lifetimes of SSDs with some workloads (e.g. Financial) by reducing the number of block erase counts by up to 79% relative to a reactive algorithm for write-dominant enterprise workloads.

  8. Chemical analyses and preliminary interpretation of waters collected...

    Open Energy Info (EERE)

    system appears to be a hot water type. The surface expression of fumarole and acid sulfate pools and shallow steam wells gives a false indication of an extensive vapor...

  9. DOE SBIR Phase II Final Report: Distributed Relevance Ranking in Heterogeneous Document Collections

    SciTech Connect (OSTI)

    Abe Lederman

    2007-01-08

    This report contains the comprehensive summary of the work performed on the SBIR Phase II project (Distributed Relevance Ranking in Heterogeneous Document Collections) at Deep Web Technologies (http://www.deepwebtech.com). We have successfully completed all of the tasks defined in our SBIR Proposal work plan (See Table 1 - Phase II Tasks Status). The project was completed on schedule and we have successfully deployed an initial production release of the software architecture at DOE-OSTI for the Science.gov Alliance's search portal (http://www.science.gov). We have implemented a set of grid services that supports the extraction, filtering, aggregation, and presentation of search results from numerous heterogeneous document collections. Illustration 3 depicts the services required to perform QuickRank filtering of content as defined in our architecture documentation. Functionality that has been implemented is indicated by the services highlighted in green. We have successfully tested our implementation in a multi-node grid deployment both within the Deep Web Technologies offices, and in a heterogeneous geographically distributed grid environment. We have performed a series of load tests in which we successfully simulated 100 concurrent users submitting search requests to the system. This testing was performed on deployments of one, two, and three node grids with services distributed in a number of different configurations. The preliminary results from these tests indicate that our architecture will scale well across multi-node grid deployments, but more work will be needed, beyond the scope of this project, to perform testing and experimentation to determine scalability and resiliency requirements. We are pleased to report that a production quality version (1.4) of the science.gov Alliance's search portal based on our grid architecture was released in June of 2006. This demonstration portal is currently available at http://science.gov/search30 . The portal allows the user to select from a number of collections grouped by category and enter a query expression (See Illustration 1 - Science.gov 3.0 Search Page). After the user clicks search a results page is displayed that provides a list of results from the selected collections ordered by relevance based on the query expression the user provided. Our grid based solution to deep web search and document ranking has already gained attention within DOE, other Government Agencies and a fortune 50 company. We are committed to the continued development of grid based solutions to large scale data access, filtering, and presentation problems within the domain of Information Retrieval and the more general categories of content management, data mining and data analysis.

  10. A Robust and Flexible Design for GCEP Unattended Online Enrichment Monitoring: An OLEM Collection Node Network

    SciTech Connect (OSTI)

    Younkin, James R; March-Leuba, Jose A; Garner, James R

    2013-01-01

    Oak Ridge National Laoratory (ORNL) has engineered an on-line enrichment monitor (OLEM) to continuously measure U-235 emissions from the UF6 gas flowing through a unit header pipe of a gas centrifuge enrichment plant (GCEP) as a component of the International Atomic Energy Agency s (IAEA) new generation of technology to support enrichment plant safeguards1. In contrast to other enrichment monitoring approaches, OLEM calibrates and corrects for the pressure and temperature dependent UF6 gas-density without external radiation sources by using the inherent unit header pipe pressure dynamics and combining U-235 gamma-ray spectrometery using a shielded NaI detector with gas pressure and temperature data near the spectrum measurement point to obtain the enrichment of the gas as a function of time. From a safeguards perspective, OLEM can provide early detection of a GCEP being misused for production of highly enriched uranium, but would not detect directly the isolation and use of a cascade within the production unit to produce HEU. OLEM may also reduce the number of samples collected for destructive assay and, if coupled with load cell monitoring, could support isotope mass balance verification and unattended cylinder verification. The earlier paper presented OLEM as one component along with shared load cells and unattended cylinder verification, in the IAEA emering toolbox for unattended instruments at GCEPs1 and described the OLEM concept and how previous modeling studies and field measurements helped confirm the viability of a passive on-line enrichment monitor for meeting IAEA objectives and to support the development of performance targets. Phase I of the United States Support Program (USSP) OLEM project completed a preliminary hardware, software and communications design; phase II will build and test field prototypes in controlled laboratory settings and then at an operational facility. That paper also discussed many of the OLEM collection node commercial off the shelf (COTS) components and summarized the OLEM collection node data security provisions. This paper will discuss a secure and redundant network of OLEM collection nodes, auxiliary detection units and supporting junction boxes distributed throughout a facility for monitoring enrichment on product, feed and tails unit header pipes; the purpose and capability of the built-in Electronic Optical Sealing System (EOSS) network gateway; and a network approach for obtaining reliable and authenticated pressure measurements.

  11. The US Support Program Assistance to the IAEA Safeguards Information Technology, Collection, and Analysis 2008

    SciTech Connect (OSTI)

    Tackentien,J.

    2008-06-12

    One of the United States Support Program's (USSP) priorities for 2008 is to support the International Atomic Energy Agency's (IAEA) development of an integrated and efficient safeguards information infrastructure, including reliable and maintainable information systems, and effective tools and resources to collect and analyze safeguards-relevant information. The USSP has provided funding in support of this priority for the ISIS Re-engineering Project (IRP), and for human resources support to the design and definition of the enhanced information analysis architecture project (nVision). Assistance for several other information technology efforts is provided. This paper will report on the various ongoing support measures undertaken by the USSP to support the IAEA's information technology enhancements and will provide some insights into activities that the USSP may support in the future.

  12. Collection efficiency of photoelectrons injected into near- and supercritical argon gas

    SciTech Connect (OSTI)

    Borghesani, A. F.; Lamp, P.

    2013-01-21

    Injection of photoelectrons into gaseous or liquid dielectrics is a widely used technique to produce cold plasmas in weakly ionized systems for investigating the transport properties of electrons. We report measurements of the collection efficiency of photoelectrons injected into dense argon gas for T= 152.7 K, close to the critical temperature T{sub c} Almost-Equal-To 150.9 K, and for T= 200.0 K. The high-field data agree with the Young-Bradbury model and with previous measurements below T{sub c} and at an intermediate temperature above T{sub c}. The effective, density-dependent electron-atom momentum transfer scattering cross section can be deduced. However, the weak-field data near T{sub c} show large deviations from the theoretical model. We show that the electron behavior at weak field is influenced by electrostriction effects that are only important near the critical point.

  13. A preliminary assessment of the state of harvest and collection technology for forest residues

    SciTech Connect (OSTI)

    Webb, Erin; Perlack, Robert D; Blackwelder, D. Brad; Muth, David J.; Hess, J. Richard

    2008-08-01

    To meet the 'Twenty in Ten Initiative' goals set in the 2007 State of the Union address, forest resources will be needed as feedstocks for lignocellulosic ethanol production. It has been estimated that 368 million dry tons can be produced annually in the U.S. from logging residues and fuel treatment thinnings. Currently, very little of this woody biomass is used for energy production due to the costs and difficulty in collecting and transporting this material. However, minimizing biomass costs (including harvest, handling, transport, storage, and processing costs) delivered to the refinery is necessary to develop a sustainable cellulosic ethanol industry. Achieving this goal requires a fresh look at conventional timber harvesting operations to identify ways of efficiently integrating energy wood collection and developing cost-effective technologies to harvest small-diameter trees. In conventional whole-tree logging operations, entire trees are felled and skidded from the stump to the landing. The residues (also called slash), consisting of tops and limbs, accumulate at the landing when trees are delimbed. This slash can be ground at the landing with a mobile grinder or transported to another central location with a stationary grinder. The ground material is transported via chip vans, or possibly large roll on/off containers, to the user facility. Cut-to-length harvesting systems are gaining popularity in some locations. In these operations, specialized harvesters that can fall, delimb, and cut logs to length are used. The small diameter tops and limbs accumulate along the machine's track. It can be left in the forest to dry or removed soon after harvest while logs are extracted. Removing slash during the same operation as the wood has been shown to be more efficient. However, leaving residue in the forest to dry reduces moisture content, which improves grinder performance, reduces dry matter loss during storage, and inhibits colonization of fungi that produce harmful spores. In recent years, new machines that are specially designed for collection of small diameter wood have been developed in the U.S. and Europe. Residue bundlers and balers improve transportation and handling efficiency by densifying the material and packaging it so that it can be handled with conventional equipment. An experimental integrated harvester/grinder can fall small diameter trees and feed them into a grinder. The ground material is collected in a bin that can be dumped into a chip van. The harvester head is also capable of delimbing and bucking (cut into sections) small timber to be used for pulp and posts. Limitations of these new technologies are their large capital costs and complexity, leading to high maintenance costs and the need for highly trained operators. To ensure that quality feedstock materials consistently enter the mouth of the refinery, the uniform format supply system concept proposes that feedstock diversity be managed at harvest, much like the current grain supply system. This allows for standardization of key infrastructure components and facilitation of a biomass commodity system. Challenges in achieving a uniform woody biomass supply include, but are not limited to, developing machines for efficient harvest of small-diameter trees in a range of topographies and conditions, developing machines and operating plans for grinding biomass as near to the stump as possible, developing cost-effective drying strategies to reduce losses and mold growth during wood chip storage, and quantifying environmental impacts of slash removal and fuel thinnings to aid landowner decisions and policy development.

  14. Approaches to consider covers and liners in a low-level waste disposal facility performance assessment

    SciTech Connect (OSTI)

    Seitz, R.

    2015-03-17

    On-site disposal cells are in use and being considered at several USDOE sites as the final disposition for large amounts of waste associated with cleanup of contaminated areas and facilities. These disposal cells are typically regulated by States and/or the USEPA in addition to having to comply with requirements in DOE Order 435.1, Radioactive Waste Management. The USDOE-EM Office of Site Restoration formed a working group to foster improved communication and sharing of information for personnel associated with these Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) disposal cells and work towards more consistent assumptions, as appropriate, for technical and policy considerations related to performance and risk assessments in support of a Record of Decision and Disposal Authorization Statement. One task completed by the working group addressed approaches for considering the performance of covers and liners/leachate collections systems in the context of a performance assessment (PA). A document has been prepared which provides recommendations for a general approach to address covers and liners/leachate collection systems in a PA and how to integrate assessments with defense-in-depth considerations such as design, operations and waste acceptance criteria to address uncertainties. Specific information and references are provided for details needed to address the evolution of individual components of cover and liner/leachate collection systems. This information is then synthesized into recommendations for best practices for cover and liner system design and examples of approaches to address the performance of covers and liners as part of a performance assessment of the disposal system.

  15. SUMP MEASURING SYSTEM

    SciTech Connect (OSTI)

    Vrettos, N; Athneal Marzolf, A; Casandra Robinson, C; James Fiscus, J; Daniel Krementz, D; Thomas Nance, T

    2007-11-26

    The process sumps in H-Canyon at the Savannah River Site (SRS) collect leaks from process tanks and jumpers. To prevent build-up of fissile material the sumps are frequently flushed which generates liquid waste and is prone to human error. The development of inserts filled with a neutron poison will allow a reduction in the frequency of flushing. Due to concrete deterioration and deformation of the sump liners the current dimensions of the sumps are unknown. Knowledge of these dimensions is necessary for development of the inserts. To solve this problem a remote Sump Measurement System was designed, fabricated, and tested to aid development of the sump inserts.

  16. Robust Systems Test Framework

    Energy Science and Technology Software Center (OSTI)

    2003-01-01

    The Robust Systems Test Framework (RSTF) provides a means of specifying and running test programs on various computation platforms. RSTF provides a level of specification above standard scripting languages. During a set of runs, standard timing information is collected. The RSTF specification can also gather job-specific information, and can include ways to classify test outcomes. All results and scripts can be stored into and retrieved from an SQL database for later data analysis. RSTF alsomore » provides operations for managing the script and result files, and for compiling applications and gathering compilation information such as optimization flags.« less

  17. Aerosol sampling system

    DOE Patents [OSTI]

    Masquelier, Donald A.

    2004-02-10

    A system for sampling air and collecting particulate of a predetermined particle size range. A low pass section has an opening of a preselected size for gathering the air but excluding particles larger than the sample particles. An impactor section is connected to the low pass section and separates the air flow into a bypass air flow that does not contain the sample particles and a product air flow that does contain the sample particles. A wetted-wall cyclone collector, connected to the impactor section, receives the product air flow and traps the sample particles in a liquid.

  18. System Diagram

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    System Diagram System Diagram Diagram of I/O architecture on Hopper Diagram of external I/O services on the Hopper system Last edited: 2016-02-01 08:07:48

  19. System Diagram

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    System Diagram System Diagram Diagram of IO architecture on Hopper Diagram of external IO services on the Hopper system Last edited: 2011-04-14 15:11:1...

  20. Report on the performance monitoring system for the interim waste containment at the Niagara Falls Storage Site, Lewiston, New York

    SciTech Connect (OSTI)

    Not Available

    1985-10-01

    The Niagara Falls Storage Site (NFSS) is an interim storage site for low-level radioactive waste, established by the US Department of Energy (DOE) at Lewiston, New York. The waste containment structure for encapsulating low-level radioactive waste at the NFSS has been designed to minimize infiltration of rainfall, prevent pollution of groundwater, preclude formation of leachate, and prevent radon emanation. Accurately determining the performance of the main engineered elements of the containment structure will be important in establishing confidence in the ability of the structure to retain the wastes. For this purpose, a waste containment performance monitoring system has been developed to verify that these elements are functioning as intended. The key objective of the performance monitoring system is the early detection of trends that could be indicative of weaknesses developing in the containment structure so that corrective action can be taken before the integrity of the structure is compromised. Consequently, subsurface as well as surface monitoring techniques will be used. After evaluating several types of subsurface instrumentation, it was determined that vibrating wire pressure transducers, in combination with surface monitoring techniques, would satisfactorily monitor the parameters of concern, such as water accumulation inside the containment facility, waste settlement, and shrinkage of the clay cover. Surface monitoring will consist of topographic surveys based on predetermined gridlines, walkover surveys, and aerial photography to detect vegetative stress or other changes not evident at ground level. This report details the objectives of the performance monitoring system, identifies the elements of the containment design whose performance will be monitored, describes the monitoring system recommended, and outlines the costs associated with the monitoring system. 5 refs., 4 figs., 3 tabs.

  1. Solid-state detector and optical system for microchip analyzers

    DOE Patents [OSTI]

    Mathies, Richard A.; Kamei, Toshihiro; Scherer, James R.; Street, Robert A.

    2005-03-15

    A miniaturized optical excitation and detector system is described for detecting fluorescently labeled analytes in electrophoretic microchips and microarrays. The system uses miniature integrated components, light collection, optical fluorescence filtering, and an amorphous a-Si:H detector for detection. The collection of light is accomplished with proximity gathering and/or a micro-lens system. Optical filtering is accomplished by integrated optical filters. Detection is accomplished utilizing a-Si:H detectors.

  2. File Systems

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    File Systems File Systems For a general description of the different file systems available on PDSF please see Eliza File Systems and Other File Systems. Below is a summary of how ATLAS uses the various systems: /common In the past ATLAS used /common primarily for their software installations but with cvmfs (see below) this is no longer necessary. ATLAS users also have made personal directories under /common/atlas. However, this is not the intended use of /common, as described on Other File

  3. Computer System,

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    undergraduate summer institute http:isti.lanl.gov (Educational Prog) 2016 Computer System, Cluster, and Networking Summer Institute Purpose The Computer System,...

  4. Secure Video Surveillance System Acquisition Software

    Energy Science and Technology Software Center (OSTI)

    2009-12-04

    The SVSS Acquisition Software collects and displays video images from two cameras through a VPN, and store the images onto a collection controller. The software is configured to allow a user to enter a time window to display up to 2 1/2, hours of video review. The software collects images from the cameras at a rate of 1 image per second and automatically deletes images older than 3 hours. The software code operates in amore » linux environment and can be run in a virtual machine on Windows XP. The Sandia software integrates the different COTS software together to build the video review system.« less

  5. Webinar May 14: H2 Refuel H-Prize Technical Data Collection Requiremen...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    4: H2 Refuel H-Prize Technical Data Collection Requirements Webinar May 14: H2 Refuel H-Prize Technical Data Collection Requirements April 6, 2015 - 11:26am Addthis The technical...

  6. Giant Collective Spin-Orbit Field in a Quantum Well: Fine Structure...

    Office of Scientific and Technical Information (OSTI)

    Giant Collective Spin-Orbit Field in a Quantum Well: Fine Structure of Spin Plasmons Citation Details In-Document Search Title: Giant Collective Spin-Orbit Field in a Quantum Well: ...

  7. Lattice and Collective Effects for PEP-X

    SciTech Connect (OSTI)

    Bane, Karl; Cai, Yunhai; Chao, Alex; Hettel, Robert; Huang, Zhirong; Nosochkov, Yuri; Stupakov, Gennady; Wang, Lanfa; Wang, Min-Huey; /SLAC

    2008-05-13

    This is a more comprehensive report of the accelerator physics in the white paper 'PEP-X Light Source at SLAC'. A new light source called 'PEP-X' would reside in the 2.2-km PEP-II tunnel. It has a hybrid lattice where two of its six arcs contain DBA cells that provide a total of 30 straight sections for insertion device beam lines and the remaining arcs contain TME cells for an extremely low emittance. Using 90 meter damping wigglers the horizontal emittance at 4.5 GeV is further reduced to 0.1 nm-rad. Many collective effects including intra-beam scattering, Touschek lifetime, and fast ion instability are studied. We expect that PEP-X will produce photon beams having brightnesses near 10{sup 22} (ph/s/mm{sup 2}/mrad{sup 2}/0.1% BW) at 10 keV and 10{sup 21} at 35 keV.

  8. User Statistics Collection Practices Archives | U.S. DOE Office of Science

    Office of Science (SC) Website

    (SC) Policies and Processes » User Statistics Collection Practices » User Statistics Collection Practices Archives User Facilities User Facilities Home User Facilities at a Glance User Resources User Statistics Policies and Processes Definition Designation Process Official List of SC User Facilities User Statistics Collection Practices User Statistics Collection Practices Archives Science Highlights Frequently Asked Questions User Facility News Contact Information Office of Science U.S.

  9. In the OSTI Collections: Carbon Sequestration, Figure 1 | OSTI, US Dept of

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Energy, Office of Scientific and Technical Information In the OSTI Collections: Carbon Sequestration, Figure 1

  10. Preliminary Evaluation of the Trench 1 Collection Drain Floodplain Area of

    Energy Savers [EERE]

    the Shiprock, New Mexico, Site | Department of Energy Preliminary Evaluation of the Trench 1 Collection Drain Floodplain Area of the Shiprock, New Mexico, Site Preliminary Evaluation of the Trench 1 Collection Drain Floodplain Area of the Shiprock, New Mexico, Site Preliminary Evaluation of the Trench 1 Collection Drain Floodplain Area of the Shiprock, New Mexico, Site PDF icon Preliminary Evaluation of the Trench 1 Collection Drain Floodplain Area of the Shiprock, New Mexico, Site More

  11. Public Law 104-134, the Debt Collection Improvement Act of 1996 |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy 4-134, the Debt Collection Improvement Act of 1996 Public Law 104-134, the Debt Collection Improvement Act of 1996 Public Law 104-13, the Debt Collection Improvement Act of 1996 PDF icon Public Law 104-134, the Debt Collection Improvement Act of 1996 More Documents & Publications PSH-14-0004 - In the Matter of Personnel Security PSH-14-0094 - In the Matter of Personnel Security Programs of HUD 2013

  12. WITS - WASTE DATA COLLECTION WITH OUR PALMS AT OUR FINGERTIPS

    SciTech Connect (OSTI)

    B. MARTINEZ

    2000-11-01

    The waste management and environmental compliance group (NMT-7) at the Los Alamos National Laboratory (LANL) has initiated a project to build a computer-based system for tracking inventory, storage and disposal information for hazardous and radioactive waste and contaminated byproducts. This project, the Waste Inventory Tracking System (WITS), will initially be used in TA-55 (which includes the Los Alamos National Laboratory Plutonium Facility) and the Chemical and Metallurgy Research (CMR) building where wastes are generated. The system handles numerous waste types with variation in size, disposal method, and hazard classification including: low level waste such as room trash (compactable waste), SEG waste (non-compactable), and over-sized waste, mixed waste, hazardous and chemical waste, universal waste, and waste containing asbestos and PCB's. WITS is designed to provide up-to-date location, status, content information, radioactivity analyses, and other inventory information for every waste item and container managed by NMT-7. The system will support comprehensive reporting capabilities and cradle-to-grave audit trails. WITS is intended to facilitate handling of waste by NMT-7 staff to help minimize waste disposal costs, ensure compliance with applicable regulations, and standardize waste management methodologies and practices. This paper compares current management practices with revised methodologies supported by WITS. It shows how automating inventory tracking helps achieve these goals.

  13. Work Authorization System

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    ... long-term liabilities; and accounting for equity revenues, collections, expenses, and ... long-term liabilities; and accounting for equity revenues, collections, expenses, and ...

  14. Pressure Systems

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Engineering > Pressure Systems Privacy and Security Notice Skip over navigation Search the JLab Site Pressure Systems Please upgrade your browser. This site's design is only visible in a graphical browser that supports web standards, but its content is accessible to any browser. Concerns? Engineering Division print version Design Authority List Design Authority Toolbox Welding Documentation Pressure Systems Forms PS-1 Pressure System Project Cover Sheet PS-2 Overpressure by System Design

  15. Directory of Energy Data Collection Forms: Forms in use as of October 1993

    SciTech Connect (OSTI)

    Not Available

    1993-12-28

    This is the seventeenth edition of the Directory of Energy Data Collection forms, an authoritative listing of selected public use forms currently used as basic energy information gathering tools by the Department of Energy (DOE). Originally entitled EIA Data Collection forms, this directory provides an overview of DOE`s energy information collection programs for decisionmakers in Government and industry.

  16. OMB Form 83-D, Paperwork Reduction Act Collection Discontinuation Form, October 2004

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    COLLECTION DISCONTINUATION FORM Agency/Subagency OMB Control Number Current Expiration Date Requested Expiration Date to Discontinue Collection Title of Collection: Reason for Discontinuation: For OIRA Use Date: OMB FORM 83-D, 10/2004 Signature of Senior Official or Designee: month year month year Adobe Professional 7.0

  17. U.S. DEPARTMENT OF ENERGY Information Collection Clearance Manager Appointment

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    1.5 (05-2014) U.S. DEPARTMENT OF ENERGY Information Collection Clearance Manager Appointment SECTION I. Appointment Information Pursuant to DOE Order 200.2, Information Collection Management Program, (Name) _______________________________________________ is hereby appointed to serve as the Information Collection Clearance Manager representing (DOE Element) _______________________________________________. The incumbents' responsibilities include providing varying levels of administrative and

  18. Audio-magnetotelluric data collected in the area of Beatty, Nevada

    SciTech Connect (OSTI)

    Williams, J.M.

    1998-11-01

    In the summer of 1997, electrical geophysical data was collected north of Beatty, Nevada. Audio-magnetotellurics (AMT) was the geophysical method used to collect 16 stations along two profiles. The purpose of this data collection was to determine the depth to the alluvial basement, based upon the needs of the geologists requesting the data.

  19. Adaptable radiation monitoring system and method

    DOE Patents [OSTI]

    Archer, Daniel E. (Livermore, CA); Beauchamp, Brock R. (San Ramon, CA); Mauger, G. Joseph (Livermore, CA); Nelson, Karl E. (Livermore, CA); Mercer, Michael B. (Manteca, CA); Pletcher, David C. (Sacramento, CA); Riot, Vincent J. (Berkeley, CA); Schek, James L. (Tracy, CA); Knapp, David A. (Livermore, CA)

    2006-06-20

    A portable radioactive-material detection system capable of detecting radioactive sources moving at high speeds. The system has at least one radiation detector capable of detecting gamma-radiation and coupled to an MCA capable of collecting spectral data in very small time bins of less than about 150 msec. A computer processor is connected to the MCA for determining from the spectral data if a triggering event has occurred. Spectral data is stored on a data storage device, and a power source supplies power to the detection system. Various configurations of the detection system may be adaptably arranged for various radiation detection scenarios. In a preferred embodiment, the computer processor operates as a server which receives spectral data from other networked detection systems, and communicates the collected data to a central data reporting system.

  20. Radiant energy collection and conversion apparatus and method

    DOE Patents [OSTI]

    Hunt, Arlon J.

    1982-01-01

    The apparatus for collecting radiant energy and converting same to alternate energy form includes a housing having an interior space and a radiation transparent window allowing, for example, solar radiation to be received in the interior space of the housing. Means are provided for passing a stream of fluid past said window and for injecting radiation absorbent particles in said fluid stream. The particles absorb the radiation and because of their very large surface area, quickly release the heat to the surrounding fluid stream. The fluid stream particle mixture is heated until the particles vaporize. The fluid stream is then allowed to expand in, for example, a gas turbine to produce mechanical energy. In an aspect of the present invention properly sized particles need not be vaporized prior to the entrance of the fluid stream into the turbine, as the particles will not damage the turbine blades. In yet another aspect of the invention, conventional fuel injectors are provided to inject fuel into the fluid stream to maintain the proper temperature and pressure of the fluid stream should the source of radiant energy be interrupted. In yet another aspect of the invention, an apparatus is provided which includes means for providing a hot fluid stream having hot particles disbursed therein which can radiate energy, means for providing a cooler fluid stream having cooler particles disbursed therein, which particles can absorb radiant energy and means for passing the hot fluid stream adjacent the cooler fluid stream to warm the cooler fluid and cooler particles by the radiation from the hot fluid and hot particles.

  1. Radiant energy collection and conversion apparatus and method

    DOE Patents [OSTI]

    Hunt, A.J.

    The apparatus for collecting radiant energy and converting to alternate energy forms includes a housing having an interior space and a radiation transparent window allowing solar radiation to be received in the interior space of the housing. Means are provided for passing a stream of fluid past the window and for injecting radiation absorbent particles in said fluid stream. The particles absorb the radiation and because of their very large surface area, quickly release the heat to the surrounding fluid stream. The fluid stream particle mixture is heated until the particles vaporize. The fluid stream is then allowed to expand in, for example, a gas turbine to produce mechanical energy. In an aspect of the present invention properly sized particles need not be vaporized prior to the entrance of the fluid stream into the turbine, as the particles will not damage the turbine blades. In yet another aspect of the invention, conventional fuel injectors are provided to inject fuel into the fluid stream to maintain the proper temperature and pressure of the fluid stream should the source of radiant energy be interrupted. In yet another aspect of the invention, an apparatus is provided which includes means for providing a hot fluid stream having hot particles disbursed therein which can radiate energy, means for providing a cooler fluid stream having cooler particles disbursed therein, which particles can absorb radiant energy and means for passing the hot fluid stream adjacent the cooler fluid stream to warm the cooler fluid and cooler particles by the radiation from the hot fluid and hot particles.

  2. File Systems

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    File Systems File Systems For a general description of the different file systems available on PDSF please see Eliza File Systems and Other File Systems. Below is a summary of how ALICE uses the various systems: /common ALICE uses /common to build the software that supports its grid-based automated production work. This software includes AliRoot, Geant, AliEn, and XRootD. /eliza6, /eliza8, /eliza17 ALICE has space on 3 elizas: 16TB on /eliza6, 6TB on /eliza8 and 11TB on /eliza17. The space on

  3. File Systems

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    File Systems File Systems For a general description of the different file systems available on PDSF please see Eliza File Systems and Other File Systems. Below is a summary of how STAR uses the various systems: /common The STAR software is installed on /common. For 32sl44 it is under /common/star/star44 and for sl53 it is under /common/star/star53. In both cases the software consists primarily of a STAR-specific ROOT installation on which releases of the STAR libraries are built as shown on the

  4. Files systems

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Files systems Files systems NERSC's global home and project file systems are available on Franklin. Additionally, Franklin has over 400 TB of locally attached high-performance /scratch disk space For information on the NERSC file systems, see the link at right. Scratch File Systems Size Aggregate Peak Performance # IO Servers Interconnect File System Software Disk Array Vendor $SCRATCH 209 TB 17 GB/sec 24 Lustre DDN $SCRATCH2 209 TB 17 GB/sec 24 Lustre DDN SCRATCH and SCRATCH2 There are two

  5. Method and device for removing a non-aqueous phase liquid from a groundwater system

    DOE Patents [OSTI]

    Looney, Brian B. (Aiken, SC); Rossabi, Joseph (Aiken, SC); Riha, Brian D. (Augusta, GA)

    2002-01-01

    A device for removing a non-aqueous phase liquid from a groundwater system includes a generally cylindrical push-rod defining an internal recess therein. The push-rod includes first and second end portions and an external liquid collection surface. A liquid collection member is detachably connected to the push-rod at one of the first and second end portions thereof. The method of the present invention for removing a non-aqueous phase liquid from a contaminated groundwater system includes providing a lance including an external hydrophobic liquid collection surface, an internal recess, and a collection chamber at the bottom end thereof. The lance is extended into the groundwater system such that the top end thereof remains above the ground surface. The liquid is then allowed to collect on the liquid collection surface, and flow downwardly by gravity into the collection chamber to be pumped upwardly through the internal recess in the lance.

  6. Using contingent valuation to explore willingness to pay for renewable energy: A comparison of collective and voluntary payment vehicles

    SciTech Connect (OSTI)

    Wiser, Ryan H.

    2002-07-28

    Some of the most basic questions about the organization and functioning of society involve issues raised by the existence of public goods. With respect to environmental public goods, how should funds used to support environmental improvement be collected and used? In particular, are collective, mandatory payments superior to voluntary, charitable payments due to the possibility of free riding? And to what degree should the government be involved in spending these funds: should the government directly fund environmental improvement projects or should the private sector be used to collect funds and determine funding priorities? This report explores these questions from the perspective of renewable energy: wind, geothermal, biomass, hydropower, and solar. In particular, this report analyzes the payment preferences of U.S. households through the implementation of a large-scale contingent valuation (CV) survey of willingness to pay (WTP) for renewable energy. Renewable energy can be supported through a mandatory ''tax'' on electric bills or through voluntary payments via green power marketing; the government may or may not be heavily involved in the collection and expenditure of such funds. The question of how households prefer to pay for renewable energy is therefore highly relevant. The primary objective of this study is to explore variations in stated WTP for renewable energy under the following four payment and provision contexts: (1) A mandatory increase in the electricity bills of all customers, the funds from which are collected and spent by the government on renewable energy projects. (2) A voluntary increase in the electricity bills of those customers who choose to pay, the funds from which are collected and spent by the government on renewable energy projects. (3) A voluntary increase in the electricity bills of those customers who choose to pay, the funds from which are collected and spent by electricity suppliers on renewable energy projects. (4) A mandatory increase in the electricity bills of all customers, the funds from which are collected and spent by electricity suppliers on renewable energy projects. These payment and provision scenarios are consistent with contemporary forms of support for renewable energy. The first scenario--mandatory payments and government provision--is consistent with a system-benefits charge policy, a policy that has been adopted in 15 U.S. states. The third scenario--voluntary payments to an electricity supplier--is consistent with competitive green power marketing. The fourth scenario--mandatory payments through electricity suppliers--is consistent with a renewables portfolio standard, a policy adopted in thirteen U.S. states as of mid 2003. The second scenario--voluntary payments and government provision--has only been used in a limited fashion in the United States. In addition to having contemporary policy relevance, these four contingent valuation scenarios allow one to distinguish differences in stated WTP based on: (1) the payment method--is WTP affected by whether payments are to be made collectively or voluntarily? and (2) the provision arrangement--does the manner in which a good is provided, in this case through the government or the private sector, affect stated WTP? A split-sample, dichotomous choice contingent valuation survey of 1,574 U.S. residents was developed and implemented to test the sensitivity of stated WTP to these variables at three different payment levels, or bid points. Three secondary objectives also influenced research design, and are discussed in this report. First, this study indirectly and tentatively evaluates the importance of ''participation expectations'' in contingent valuation surveys: specifically, are individuals who state a WTP for renewable energy more likely to think that others will also contribute? Such relationships are commonly discussed in the sociology, social psychology, and marketing literatures, and are also frequently referenced in the collective action literature, but have yet to be tested thoroughly in a contingent valuation co

  7. BUNCOMBE COUNTY WASTEWATER PRE-TREATMENT AND LANDFILL GAS TO ENERGY PROJECT

    SciTech Connect (OSTI)

    Jon Creighton

    2012-03-13

    The objective of this project was to construct a landfill gas-to-energy (LFGTE) facility that generates a renewable energy source utilizing landfill gas to power a 1.4MW generator, while at the same time reducing the amount of leachate hauled offsite for treatment. The project included an enhanced gas collection and control system, gas conditioning equipment, and a 1.4 MW generator set. The production of cleaner renewable energy will help offset the carbon footprint of other energy sources that are currently utilized.

  8. Summary - Operational Issues at the Environmental Restoration Disposal Facility (ERDF) at Hanford

    Office of Environmental Management (EM)

    ERDF ETR Report Date: June 2007 ETR-6 United States Department of Energy Office of Environmental Management (DOE-EM) External Technical Review of the Operational Issues at the Environmental Restoration Disposal Facility(ERDF) at Hanford Why DOE-EM Did This Review The ERDF is a large- scale disposal facility authorized to receive waste from Hanford cleanup activities. It contains double-lined cells with a RCRA Subtitle C- type liner and leachate collection system. By 2007, 6.8 million tons of

  9. Quantitative Adaptation Analytics for Assessing Dynamic Systems of Systems.

    SciTech Connect (OSTI)

    Gauthier, John H.; Miner, Nadine E.; Wilson, Michael L.; Le, Hai D.; Kao, Gio K; Melander, Darryl J.; Longsine, Dennis Earl; Vander Meer, Robert Charles,

    2015-01-01

    Our society is increasingly reliant on systems and interoperating collections of systems, known as systems of systems (SoS). These SoS are often subject to changing missions (e.g., nation- building, arms-control treaties), threats (e.g., asymmetric warfare, terrorism), natural environments (e.g., climate, weather, natural disasters) and budgets. How well can SoS adapt to these types of dynamic conditions? This report details the results of a three year Laboratory Directed Research and Development (LDRD) project aimed at developing metrics and methodologies for quantifying the adaptability of systems and SoS. Work products include: derivation of a set of adaptability metrics, a method for combining the metrics into a system of systems adaptability index (SoSAI) used to compare adaptability of SoS designs, development of a prototype dynamic SoS (proto-dSoS) simulation environment which provides the ability to investigate the validity of the adaptability metric set, and two test cases that evaluate the usefulness of a subset of the adaptability metrics and SoSAI for distinguishing good from poor adaptability in a SoS. Intellectual property results include three patents pending: A Method For Quantifying Relative System Adaptability, Method for Evaluating System Performance, and A Method for Determining Systems Re-Tasking.

  10. System for particle concentration and detection

    SciTech Connect (OSTI)

    Morales, Alfredo M.; Whaley, Josh A.; Zimmerman, Mark D.; Renzi, Ronald F.; Tran, Huu M.; Maurer, Scott M.; Munslow, William D.

    2013-03-19

    A new microfluidic system comprising an automated prototype insulator-based dielectrophoresis (iDEP) triggering microfluidic device for pathogen monitoring that can eventually be run outside the laboratory in a real world environment has been used to demonstrate the feasibility of automated trapping and detection of particles. The system broadly comprised an aerosol collector for collecting air-borne particles, an iDEP chip within which to temporarily trap the collected particles and a laser and fluorescence detector with which to induce a fluorescence signal and detect a change in that signal as particles are trapped within the iDEP chip.

  11. System Effectiveness

    SciTech Connect (OSTI)

    Powell, Danny H; Elwood Jr, Robert H

    2011-01-01

    An effective risk assessment system is needed to address the threat posed by an active or passive insider who, acting alone or in collusion, could attempt diversion or theft of nuclear material. It is critical that a nuclear facility conduct a thorough self-assessment of the material protection, control, and accountability (MPC&A) system to evaluate system effectiveness. Self-assessment involves vulnerability analysis and performance testing of the MPC&A system. The process should lead to confirmation that mitigating features of the system effectively minimize the threat, or it could lead to the conclusion that system improvements or upgrades are necessary to achieve acceptable protection against the threat. Analysis of the MPC&A system is necessary to understand the limits and vulnerabilities of the system to internal threats. Self-assessment helps the facility be prepared to respond to internal threats and reduce the risk of theft or diversion of nuclear material. MSET is a self-assessment or inspection tool utilizing probabilistic risk assessment (PRA) methodology to calculate the system effectiveness of a nuclear facility's MPC&A system. MSET analyzes the effectiveness of an MPC&A system based on defined performance metrics for MPC&A functions based on U.S. and international best practices and regulations. A facility's MC&A system can be evaluated at a point in time and reevaluated after upgrades are implemented or after other system changes occur. The total system or specific subareas within the system can be evaluated. Areas of potential performance improvement or system upgrade can be assessed to determine where the most beneficial and cost-effective improvements should be made. Analyses of risk importance factors show that sustainability is essential for optimal performance. The analyses reveal where performance degradation has the greatest detrimental impact on total system risk and where performance improvements have the greatest reduction in system risk. The risk importance factors show the amount of risk reduction achievable with potential upgrades and the amount of risk reduction actually achieved after upgrades are completed. Applying the risk assessment tool gives support to budget prioritization by showing where budget support levels must be sustained for MC&A functions most important to risk. Results of the risk assessment are also useful in supporting funding justifications for system improvements that significantly reduce system risk.

  12. Mercury in Fish Collected Upstream and Downstream of Los Alamos National Laboratory, New Mexico: 1991--2004.

    SciTech Connect (OSTI)

    P.R. Fresquez

    2004-10-15

    Small amounts of mercury (Hg) may exist in some canyon drainage systems within Los Alamos National Laboratory lands as a result of past discharges of untreated effluents. This paper reports on the concentrations of Hg in muscle (fillets) of various types of fish species collected downstream of LANL's influence from 1991 through 2004. The mean Hg concentration in fish from Cochiti reservoir (0.22 {micro}g/g wet weight), which is located downstream of LANL, was similar to fish collected from a reservoir upstream of LANL (Abiquiu) (0.26 {micro}g/g wet weight). Mercury concentrations in fish collected from both reservoirs exhibited significantly (Abiquiu = p < 0.05 and Cochiti = p < 0.10) decreasing trends over time. Predator fish like the northern pike (Esox lucius) contained significantly higher concentrations of Hg (0.39 {micro}g/g wet weight) than bottom-feeding fish like the white sucker (Catostomus commersoni) (0.10 {micro}g/g wet weight).

  13. The Autonomous Pathogen Detection System

    SciTech Connect (OSTI)

    Dzenitis, J M; Makarewicz, A J

    2009-01-13

    We developed, tested, and now operate a civilian biological defense capability that continuously monitors the air for biological threat agents. The Autonomous Pathogen Detection System (APDS) collects, prepares, reads, analyzes, and reports results of multiplexed immunoassays and multiplexed PCR assays using Luminex{copyright} xMAP technology and flow cytometer. The mission we conduct is particularly demanding: continuous monitoring, multiple threat agents, high sensitivity, challenging environments, and ultimately extremely low false positive rates. Here, we introduce the mission requirements and metrics, show the system engineering and analysis framework, and describe the progress to date including early development and current status.

  14. Energy Balance Bowen Ratio System

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    0 Energy Balance Bowen Ratio System Estimates of surface energy fluxes are a primary product of the data collection systems at the ARM SGP CART site. Surface fluxes tell researchers a great deal about the effects of interactions between the sun's energy and Earth. Surface fluxes of latent and sensible heat can be estimated by measuring temperature and relative humidity gradients across a vertical distance. Sensible heat is what we feel coming from a warm sidewalk or a metal car door; it can be

  15. Performance model assessment for multi-junction concentrating photovoltaic systems.

    SciTech Connect (OSTI)

    Riley, Daniel M.; McConnell, Robert.; Sahm, Aaron; Crawford, Clark; King, David L.; Cameron, Christopher P.; Foresi, James S.

    2010-03-01

    Four approaches to modeling multi-junction concentrating photovoltaic system performance are assessed by comparing modeled performance to measured performance. Measured weather, irradiance, and system performance data were collected on two systems over a one month period. Residual analysis is used to assess the models and to identify opportunities for model improvement.

  16. Directory of energy data collection forms: Forms in use as of October 1994

    SciTech Connect (OSTI)

    Not Available

    1994-12-15

    This 18th edition directory provides an overview of DOE`s energy information collection programs for decisionmakers in Government and industry; selected public use forms currently used as basic energy information gathering tools by DOE are covered. For each form, an abstract is included that describes the form`s uses, its respondents, and the data collected. Also shown are frequently requested items: energy sources and functions covered by the form, general categories of respondents, collection frequency, public laws and regulations, reporting requirement, name and phone number of the data collection manager, and the publications resulting from the data collection. Indexes, arranged according to energy source/function, publications, respondent categories, former EIA form number designations, and collection authorities, are provided.

  17. Solar thermal power system

    DOE Patents [OSTI]

    Bennett, Charles L.

    2010-06-15

    A solar thermal power generator includes an inclined elongated boiler tube positioned in the focus of a solar concentrator for generating steam from water. The boiler tube is connected at one end to receive water from a pressure vessel as well as connected at an opposite end to return steam back to the vessel in a fluidic circuit arrangement that stores energy in the form of heated water in the pressure vessel. An expander, condenser, and reservoir are also connected in series to respectively produce work using the steam passed either directly (above a water line in the vessel) or indirectly (below a water line in the vessel) through the pressure vessel, condense the expanded steam, and collect the condensed water. The reservoir also supplies the collected water back to the pressure vessel at the end of a diurnal cycle when the vessel is sufficiently depressurized, so that the system is reset to repeat the cycle the following day. The circuital arrangement of the boiler tube and the pressure vessel operates to dampen flow instabilities in the boiler tube, damp out the effects of solar transients, and provide thermal energy storage which enables time shifting of power generation to better align with the higher demand for energy during peak energy usage periods.

  18. Temperature System

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    1 Soil Water and Temperature System  SWATS In the realm of global climate modeling, numerous variables affect the state of the atmosphere and climate. One important area is soil moisture and temperature. The ARM Program uses several types of instruments to gather soil moisture information. An example is the soil water and temperature system (SWATS) (Figure 1). A SWATS is located at each of 21 extended facility sites within the CART site boundary. Each system is configured to measure soil

  19. Methods to Collect, Compile, and Analyze Observed Short-lived Fission Product Gamma Data

    SciTech Connect (OSTI)

    Finn, Erin C.; Metz, Lori A.; Payne, Rosara F.; Friese, Judah I.; Greenwood, Lawrence R.; Kephart, Jeremy D.; Pierson, Bruce D.; Ellis, Tere A.

    2011-09-29

    A unique set of fission product gamma spectra was collected at short times (4 minutes to 1 week) on various fissionable materials. Gamma spectra were collected from the neutron-induced fission of uranium, neptunium, and plutonium isotopes at thermal, epithermal, fission spectrum, and 14-MeV neutron energies. This report describes the experimental methods used to produce and collect the gamma data, defines the experimental parameters for each method, and demonstrates the consistency of the measurements.

  20. User Statistics Collection Practices | U.S. DOE Office of Science (SC)

    Office of Science (SC) Website

    User Statistics Collection Practices User Facilities User Facilities Home User Facilities at a Glance User Resources User Statistics Policies and Processes Definition Designation Process Official List of SC User Facilities User Statistics Collection Practices User Statistics Collection Practices Archives Science Highlights Frequently Asked Questions User Facility News Contact Information Office of Science U.S. Department of Energy 1000 Independence Ave., SW Washington, DC 20585 P: (202)

  1. Collection Descriptions for the E-print Network -- Energy, science, and

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    technology for the research community -- Hosted by the Office of Scientific and Technical Information, U.S. Department of Energy Collection Descriptions E-prints on Subject Web Sites Coverage: provided by each unique Web site crawled (over 2.5 million documents) Description: The E-prints on Subject Web Sites collections contain electronic scientific and technical information created by scientists and research engineers active in their respective fields. These collections are intended for use

  2. Exhaust system with emissions storage device and plasma reactor

    DOE Patents [OSTI]

    Hoard, John W. (Livonia, MI)

    1998-01-01

    An exhaust system for a combustion system, comprising a storage device for collecting NO.sub.x, hydrocarbon, or particulate emissions, or mixture of these emissions, and a plasma reactor for destroying the collected emissions is described. After the emission is collected in by the storage device for a period of time, the emission is then destroyed in a non-thermal plasma generated by the plasma reactor. With respect to the direction of flow of the exhaust stream, the storage device must be located before the terminus of the plasma reactor, and it may be located wholly before, overlap with, or be contained within the plasma reactor.

  3. Integrated Building Management System (IBMS)

    SciTech Connect (OSTI)

    Anita Lewis

    2012-07-01

    This project provides a combination of software and services that more easily and cost-effectively help to achieve optimized building performance and energy efficiency. Featuring an open-platform, cloud- hosted application suite and an intuitive user experience, this solution simplifies a traditionally very complex process by collecting data from disparate building systems and creating a single, integrated view of building and system performance. The Fault Detection and Diagnostics algorithms developed within the IBMS have been designed and tested as an integrated component of the control algorithms running the equipment being monitored. The algorithms identify the normal control behaviors of the equipment without interfering with the equipment control sequences. The algorithms also work without interfering with any cooperative control sequences operating between different pieces of equipment or building systems. In this manner the FDD algorithms create an integrated building management system.

  4. Miniaturized flow injection analysis system

    DOE Patents [OSTI]

    Folta, James A. (Livermore, CA)

    1997-01-01

    A chemical analysis technique known as flow injection analysis, wherein small quantities of chemical reagents and sample are intermixed and reacted within a capillary flow system and the reaction products are detected optically, electrochemically, or by other means. A highly miniaturized version of a flow injection analysis system has been fabricated utilizing microfabrication techniques common to the microelectronics industry. The microflow system uses flow capillaries formed by etching microchannels in a silicon or glass wafer followed by bonding to another wafer, commercially available microvalves bonded directly to the microflow channels, and an optical absorption detector cell formed near the capillary outlet, with light being both delivered and collected with fiber optics. The microflow system is designed mainly for analysis of liquids and currently measures 38.times.25.times.3 mm, but can be designed for gas analysis and be substantially smaller in construction.

  5. Miniaturized flow injection analysis system

    DOE Patents [OSTI]

    Folta, J.A.

    1997-07-01

    A chemical analysis technique known as flow injection analysis is described, wherein small quantities of chemical reagents and sample are intermixed and reacted within a capillary flow system and the reaction products are detected optically, electrochemically, or by other means. A highly miniaturized version of a flow injection analysis system has been fabricated utilizing microfabrication techniques common to the microelectronics industry. The microflow system uses flow capillaries formed by etching microchannels in a silicon or glass wafer followed by bonding to another wafer, commercially available microvalves bonded directly to the microflow channels, and an optical absorption detector cell formed near the capillary outlet, with light being both delivered and collected with fiber optics. The microflow system is designed mainly for analysis of liquids and currently measures 38{times}25{times}3 mm, but can be designed for gas analysis and be substantially smaller in construction. 9 figs.

  6. A Collection of Algal Genomes from the JGI (Conference) | SciTech...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Citation Details In-Document Search Title: A Collection of Algal Genomes from the JGI Algae, defined as photosynthetic eukaryotes other than plants, constitute a major component...

  7. Roadmap to Monitor Data Collected during the WSCC Breakup of August 10, 1996

    SciTech Connect (OSTI)

    Hauer, John F.; Burns, J. W.

    2010-06-30

    This document describes a roadmap to assist users in using the monitoring data collected during the WSCC breakup of August 10, 1996.

  8. Collection of solid and gaseous samples to diagnose inertial confinement fusion implosions

    SciTech Connect (OSTI)

    Stoyer, M. A.; Velsko, C. A.; Spears, B. K.; Hicks, D. G.; Hudson, G. B.; Sangster, T. C.; Freeman, C. G.

    2012-02-15

    Collection of representative samples of debris following inertial confinement fusion implosions in order to diagnose implosion conditions and efficacy is a challenging endeavor because of the unique conditions within the target chamber such as unconverted laser light, intense pulse of x-rays, physical chunks of debris, and other ablative effects. We present collection of gas samples following an implosion for the first time. High collection fractions for noble gases were achieved. We also present collection of solid debris samples on flat plate collectors. Geometrical collection efficiencies for Au hohlraum material were achieved and collection of capsule debris (Be and Cu) was also observed. Asymmetric debris distributions were observed for Au and Be samples. Collection of Be capsule debris was higher for solid collectors viewing the capsule through the laser entrance hole in the hohlraum than for solid collectors viewing the capsule around the waist of the hohlraum. Collection of Au hohlraum material showed the opposite pattern: more Au debris was collected around the waist than through the laser entrance hole. The solid debris collectors were not optimized for minimal Cu backgrounds, which limited the conclusions about the symmetry of the Cu debris. The quality of the data limited conclusions on chemical fractionation effects within the burning, expanding, and then cooling plasma.

  9. User Statistics Collection Practices | U.S. DOE Office of Science...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    User Statistics Collection Practices User Facilities User Facilities Home User Facilities at a Glance User Resources User Statistics Policies and Processes Definition Designation...

  10. System Description for the KW Basin Integrated Water Treatment System (IWTS) (70.3)

    SciTech Connect (OSTI)

    DERUSSEAU, R.R.

    2000-04-18

    This is a description of the system that collects and processes the sludge and radioactive ions released by the spent nuclear fuel (SNF) processing operations conducted in the 105 KW Basin. The system screens, settles, filters, and conditions the basin water for reuse. Sludge and most radioactive ions are removed before the water is distributed back to the basin pool. This system is part of the Spent Nuclear Fuel Project (SNFP).

  11. Genotypic and phenotypic characterization of aerosolized bacteria collected from African dust events

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Wilson, Christina A.; Brigmon, Robin L.; Yeager, Chris; Smith, Garriet W.; Polson, Shawn W.

    2013-07-31

    Twenty-one bacteria were isolated and characterized from air samples collected in Africa and the Caribbean by the United States Geological Survey (USGS). Isolates were selected based on preliminary characterization as possible pathogens. Identification of the bacterial isolates was 25 achieved using 16S rRNA gene sequence analysis, fatty acid methyl esters (FAMEs) profiling, the BIOLOG Microlog® System (carbon substrate assay), and repetitive extragenic palindromic (REP)-PCR analysis. The majority of isolates (18/21) were identified as species of the genus Bacillus. Three isolates were classified within the Bacillus cereus senso lato group, which includes Bacillus anthracis, Bacillus thuringiensis, and Bacillus cereus strains. Onemore » isolate was identified as a Staphylococcus sp., 30 most closely related to species (i.e Staphylococcus kloosii, Staphylococcus warneri) that are commonly associated with human or animal skin, but can also act as opportunistic pathogen. Another isolate was tentatively identified as Tsukamurella inchonensis, a known respiratory pathogen, and was resistant to the ten antibiotics tested including vancomycin.« less

  12. Genotypic and phenotypic characterization of aerosolized bacteria collected from African dust events

    SciTech Connect (OSTI)

    Wilson, Christina A.; Brigmon, Robin L.; Yeager, Chris; Smith, Garriet W.; Polson, Shawn W.

    2013-07-31

    Twenty-one bacteria were isolated and characterized from air samples collected in Africa and the Caribbean by the United States Geological Survey (USGS). Isolates were selected based on preliminary characterization as possible pathogens. Identification of the bacterial isolates was 25 achieved using 16S rRNA gene sequence analysis, fatty acid methyl esters (FAMEs) profiling, the BIOLOG Microlog System (carbon substrate assay), and repetitive extragenic palindromic (REP)-PCR analysis. The majority of isolates (18/21) were identified as species of the genus Bacillus. Three isolates were classified within the Bacillus cereus senso lato group, which includes Bacillus anthracis, Bacillus thuringiensis, and Bacillus cereus strains. One isolate was identified as a Staphylococcus sp., 30 most closely related to species (i.e Staphylococcus kloosii, Staphylococcus warneri) that are commonly associated with human or animal skin, but can also act as opportunistic pathogen. Another isolate was tentatively identified as Tsukamurella inchonensis, a known respiratory pathogen, and was resistant to the ten antibiotics tested including vancomycin.

  13. Astrometry of Pluto from 1930-1951 observations: The Lampland plate collection

    SciTech Connect (OSTI)

    Buie, Marc W.; Folkner, William M. E-mail: william.m.folkner@jpl.nasa.gov

    2015-01-01

    We present a new analysis of 843 photographic plates of Pluto taken by Carl Lampland at Lowell Observatory from 19301951. This large collection of plates contains useful astrometric information that improves our knowledge of Pluto's orbit. This improvement provides critical support to the impending flyby of Pluto by New Horizons. New Horizons can do inbound navigation of the system to improve its targeting. This navigation is capable of nearly eliminating the sky-plane errors but can do little to constrain the time of closest approach. Thus the focus on this work was to better determine Pluto's heliocentric distance and to determine the uncertainty on that distance with a particular eye to eliminating systematic errors that might have been previously unrecognized. This work adds 596 new astrometric measurements based on the USNO CCD Astrograph Catalog 4. With the addition of these data the uncertainty of the estimated heliocentric position of Pluto in Developmental Ephemerides 432 (DE432) is at the level of 1000 km. This new analysis gives us more confidence that these estimations are accurate and are sufficient to support a successful flyby of Pluto by New Horizons.

  14. 1.2.1.1 Harvest, Collection and Storage Quarter 3 Milestone Report

    SciTech Connect (OSTI)

    Lynn M Wendt; William A Smith; Kara G Cafferty; Ian J Bonner; Qiyang Huang; Rachel D Colby

    2014-07-01

    Single pass baling of corn stover is required in order to meet targets for the herbaceous biomass 2017 logistics design case. Single-pass pass stover harvest is based on the grain harvest and generally results in stover with a moisture content of 30-50% wet basis (w.b). Aerobic storage of corn stover with high moisture results in high levels of dry matter loss (DML), up to 25%. Anaerobic storage (ensiling) reduces DML to less than 5%, but additional costs are associated with handling and transporting the extra moisture in the biomass. This milestone provides a best-estimate of costs for using high moisture feedstock within the conventional baled logistics system. The costs of three (3) anaerobic storage systems that reduce dry matter losses (bale wrap, silage tube, and silage drive over pile) are detailed in this milestone and compared to both a conventional dry-baled corn stover case and a high moisture bale case, both stored aerobically. The total logistics cost (harvest, collection, storage, and transportation) of the scenarios are as follows: the conventional multi-pass dry bale case and the single-pass high moisture case stored aerobically were nearly equivalent at $61.15 and $61.24/DMT. The single-pass bale wrap case was the lowest at $57.63/DMT. The bulk anaerobic cases were the most expensive at $84.33 for the silage tube case and $75.97 for the drive over pile, which reflect the additional expense of transporting high-moisture bulk material; however, a reduction in preprocessing costs may occur because these feedstocks are size reduced in the field. In summary, the costs estimates presented in this milestone report can be used to determine if anaerobic storage of high-moisture corn stover is an economical option for dry matter preservation.

  15. A multi-channel gel electrophoresis and continuous fraction collection apparatus for high throughput protein separation and characterization

    SciTech Connect (OSTI)

    Choi, Megan; Nordmeyer, Robert A.; Cornell, Earl; Dong, Ming; Biggin, Mark D.; Jin, Jian

    2009-10-02

    To facilitate a direct interface between protein separation by PAGE and protein identification by mass spectrometry, we developed a multichannel system that continuously collects fractions as protein bands migrate off the bottom of gel electrophoresis columns. The device was constructed using several short linear gel columns, each of a different percent acrylamide, to achieve a separation power similar to that of a long gradient gel. A Counter Free-Flow elution technique then allows continuous and simultaneous fraction collection from multiple channels at low cost. We demonstrate that rapid, high-resolution separation of a complex protein mixture can be achieved on this system using SDS-PAGE. In a 2.5 h electrophoresis run, for example, each sample was separated and eluted into 48-96 fractions over a mass range of 10-150 kDa; sample recovery rates were 50percent or higher; each channel was loaded with up to 0.3 mg of protein in 0.4 mL; and a purified band was eluted in two to three fractions (200 L/fraction). Similar results were obtained when running native gel electrophoresis, but protein aggregation limited the loading capacity to about 50 g per channel and reduced resolution.

  16. Power system

    DOE Patents [OSTI]

    Hickam, Christopher Dale (Glasford, IL)

    2008-03-18

    A power system includes a prime mover, a transmission, and a fluid coupler having a selectively engageable lockup clutch. The fluid coupler may be drivingly connected between the prime mover and the transmission. Additionally, the power system may include a motor/generator drivingly connected to at least one of the prime mover and the transmission. The power-system may also include power-system controls configured to execute a control method. The control method may include selecting one of a plurality of modes of operation of the power system. Additionally, the control method may include controlling the operating state of the lockup clutch dependent upon the mode of operation selected. The control method may also include controlling the operating state of the motor/generator dependent upon the mode of operation selected.

  17. Intelligent Leak Detection System

    SciTech Connect (OSTI)

    2014-10-27

    apability of underground carbon dioxide storage to confine and sustain injected CO2 for a very long time is the main concern for geologic CO2 sequestration. If a leakage from a geological CO2 sequestration site occurs, it is crucial to find the approximate amount and the location of the leak in order to implement proper remediation activity. An overwhelming majority of research and development for storage site monitoring has been concentrated on atmospheric, surface or near surface monitoring of the sequestered CO2. This study aims to monitor the integrity of CO2 storage at the reservoir level. This work proposes developing in-situ CO2 Monitoring and Verification technology based on the implementation of Permanent Down-hole Gauges (PDG) or ?Smart Wells? along with Artificial Intelligence and Data Mining (AI&DM). The technology attempts to identify the characteristics of the CO2 leakage by de-convolving the pressure signals collected from Permanent Down-hole Gauges (PDG). Citronelle field, a saline aquifer reservoir, located in the U.S. was considered for this study. A reservoir simulation model for CO2 sequestration in the Citronelle field was developed and history matched. The presence of the PDGs were considered in the reservoir model at the injection well and an observation well. High frequency pressure data from sensors were collected based on different synthetic CO2 leakage scenarios in the model. Due to complexity of the pressure signal behaviors, a Machine Learning-based technology was introduced to build an Intelligent Leakage Detection System (ILDS). The ILDS was able to detect leakage characteristics in a short period of time (less than a day) demonstrating the capability of the system in quantifying leakage characteristics subject to complex rate behaviors. The performance of ILDS was examined under different conditions such as multiple well leakages, cap rock leakage, availability of an additional monitoring well, presence of pressure drift and noise in the pressure sensor and uncertainty in the reservoir model.

  18. System and method for secure group transactions

    DOE Patents [OSTI]

    Goldsmith, Steven Y. (Rochester, MN)

    2006-04-25

    A method and a secure system, processing on one or more computers, provides a way to control a group transaction. The invention uses group consensus access control and multiple distributed secure agents in a network environment. Each secure agent can organize with the other secure agents to form a secure distributed agent collective.

  19. Compressor bleed cooling fluid feed system

    DOE Patents [OSTI]

    Donahoo, Eric E; Ross, Christopher W

    2014-11-25

    A compressor bleed cooling fluid feed system for a turbine engine for directing cooling fluids from a compressor to a turbine airfoil cooling system to supply cooling fluids to one or more airfoils of a rotor assembly is disclosed. The compressor bleed cooling fluid feed system may enable cooling fluids to be exhausted from a compressor exhaust plenum through a downstream compressor bleed collection chamber and into the turbine airfoil cooling system. As such, the suction created in the compressor exhaust plenum mitigates boundary layer growth along the inner surface while providing flow of cooling fluids to the turbine airfoils.

  20. New tracking system of the SND detector

    SciTech Connect (OSTI)

    Avdeeva, E. G. Bogdanchikov, A. G.; Botov, A. A.; Bukin, D. A.; Vasiljev, A. V.; Vesenev, V. M.; Golubev, V.B.; Dimova, T.V.; Druzhinin, V. P.; Korol, A. A.; Koshuba, S. V.; Obrazovsky, A. E.; Pakhtusova, E. V.; Serednyakov, S. I.; Sirotkin, A. A.; Surin, I.K.; Usov, Yu.V.; Filatov, P.V.; Kharlamov, A.G.

    2010-11-15

    A new tracking system (TS) of the Spherical Neutral Detector (SND) for experiments at the VEPP-2000 e{sup +}e{sup -} collider is described. The TS is completely assembled, mounted on the detector, and ready for collecting data from the VEPP-2000. Test experiments with cosmic-ray events and VEPP-2000 beams showed a stable operation of the system. The simulation, calibration, and reconstruction procedures were debugged by using available data.

  1. ORISE: Radiological Assessment and Monitoring System (RAMS)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Radiological Assessment and Monitoring System (RAMS) ORISE develops paperless tool to assist with data entry for radiological monitoring During the Empire 09 exercise, the Oak Ridge Institute for Science and Education tested for the first time a paperless system of data management to support the operations of the Federal Radiological Monitoring and Assessment Center. How ORISE is Making a Difference The paperless FRMAC provides tools that enables the FRMAC to collect and process field

  2. NREL: Transportation Research - Systems Analysis and Integration

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Publications Systems Analysis and Integration Publications NREL publishes technical reports, fact sheets, and other documents about its systems analysis and integration activities. For a complete collection of publications, search NREL's Publications Database or find publications via the following author and keyword selections: Authors: Robb Barnitt Brennan Borlaug Aaron Brooker Evan Burton Yuche Chen Josh Eichman Jeff Gonder Jacob Holden Tony Markel Marc Melaina Michael Penev Laurie Ramroth

  3. * Systems update

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Systems update * Mendel Move update * Cori update * Edison update * NUG annual meeting * Queues and System Usage * User Survey results * Data movement and networks mini-tutorial * Globus at NERSC * Cori, Edison and all file systems are now in operation at Wang Hall * HPSS remains in Oakland, connected to Wang Hall via a 400 GB/sec network link * A cluster servicing JGI & PDSF is shut down and in process of move from OSF to Wang Hall * No overall Genepool or PDSF downtime due to move 5 - 6 -

  4. Roof aperture system for selective collection and control of solar energy for building heating, cooling and daylighting

    DOE Patents [OSTI]

    Sanders, William J. (Kansas City, KS); Snyder, Marvin K. (Overland Park, KS); Harter, James W. (Independence, MO)

    1983-01-01

    The amount of building heating, cooling and daylighting is controlled by at least one pair of solar energy passing panels, with each panel of the pair of panels being exposed to a separate direction of sun incidence. A shutter-shade combination is associated with each pair of panels and the shutter is connected to the shade so that rectilinear movement of the shutter causes pivotal movement of the shade.

  5. Roof aperture system for selective collection and control of solar energy for building heating, cooling and daylighting

    SciTech Connect (OSTI)

    Sanders, W.J.; Harter, J.W.; Snyder, M.K.

    1983-12-06

    The amount of building heating, cooling and daylighting is controlled by at least one pair of solar energy passing panels, with each panel of the pair of panels being exposed to a separate direction of sun incidence. A shutter-shade combination is associated with each pair of panels and the shutter is connected to the shade so that rectilinear movement of the shutter causes pivotal movement of the shade.

  6. Directory of energy data collection forms. Forms in use as of October 1995

    SciTech Connect (OSTI)

    1996-01-01

    This is an authoritative listing of selected public use forms currently used as basic energy information gathering tools by the Department of Energy (DOE). This directory provides an overview of DOE`s energy information collection programs for decisionmakers in Government and industry. Forms designed to collect energy information and used by the Energy Information Administration (EIA) as of October 1995 are included in this directory. For each form listed in this directory, an abstract is included that describes the form`s uses, its respondents, and the data collected. For the reader`s convenience in finding specific types of collections, several indices have been provided in this directory. A listing of the forms grouped by energy source and function begins on page 26. Beginning on page 38 are the publications derived from the collections, and on page 50, are the forms linked to general respondent categories.

  7. Development of a Visual Inspection Data Collection Tool for Evaluation of Fielded PV Module Condition

    SciTech Connect (OSTI)

    Packard, C. E.; Wohlgemuth, J. H.; Kurtz, S. R.

    2012-08-01

    A visual inspection data collection tool for the evaluation of fielded photovoltaic (PV) modules has been developed to facilitate describing the condition of PV modules with regard to field performance. The proposed data collection tool consists of 14 sections, each documenting the appearance or properties of a part of the module. This report instructs on how to use the collection tool and defines each attribute to ensure reliable and valid data collection. This tool has been evaluated through the inspection of over 60 PV modules produced by more than 20 manufacturers and fielded at two different sites for varying periods of time. Aggregated data from such a single data collection tool has the potential to enable longitudinal studies of module condition over time, technology evolution, and field location for the enhancement of module reliability models.

  8. Battery system

    DOE Patents [OSTI]

    Dougherty, Thomas J; Wood, Steven J; Trester, Dale B; Andrew, Michael G

    2013-08-27

    A battery module includes a plurality of battery cells and a system configured for passing a fluid past at least a portion of the plurality of battery cells in a parallel manner.

  9. Accelerator Systems

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Accelerator Systems Accelerator Systems MaRIE will provide in-situ dynamic observations of microstructure for transformational materials performance in extremes CONTACT Richard Sheffield (505) 667-1237 Email Revolutionizing Microstructural Physics to Empower Nuclear Energy Realizing MaRIE's full suite of capabilities requires developing and integrating a suite of probes including proton beam radiography, electron radiography and a source of hard, brilliant, and coherent photons. The preferred

  10. Dynamic Information Architecture System

    Energy Science and Technology Software Center (OSTI)

    1997-02-12

    The Dynamic Information System (DIAS) is a flexible object-based software framework for concurrent, multidiscplinary modeling of arbitrary (but related) processes. These processes are modeled as interrelated actions caused by and affecting the collection of diverse real-world objects represented in a simulation. The DIAS architecture allows independent process models to work together harmoniously in the same frame of reference and provides a wide range of data ingestion and output capabilities, including Geographic Information System (GIS) typemore » map-based displays and photorealistic visualization of simulations in progress. In the DIAS implementation of the object-based approach, software objects carry within them not only the data which describe their static characteristics, but also the methods, or functions, which describe their dynamic behaviors. There are two categories of objects: (1) Entity objects which have real-world counterparts and are the actors in a simulation, and (2) Software infrastructure objects which make it possible to carry out the simulations. The Entity objects contain lists of Aspect objects, each of which addresses a single aspect of the Entity''s behavior. For example, a DIAS Stream Entity representing a section of a river can have many aspects correspondimg to its behavior in terms of hydrology (as a drainage system component), navigation (as a link in a waterborne transportation system), meteorology (in terms of moisture, heat, and momentum exchange with the atmospheric boundary layer), and visualization (for photorealistic visualization or map type displays), etc. This makes it possible for each real-world object to exhibit any or all of its unique behaviors within the context of a single simulation.« less

  11. Integrated Energy System Dispatch Optimization

    SciTech Connect (OSTI)

    Firestone, Ryan; Stadler, Michael; Marnay, Chris

    2006-06-16

    On-site cogeneration of heat and electricity, thermal and electrical storage, and curtailing/rescheduling demand options are often cost-effective to commercial and industrial sites. This collection of equipment and responsive consumption can be viewed as an integrated energy system(IES). The IES can best meet the sites cost or environmental objectives when controlled in a coordinated manner. However, continuously determining this optimal IES dispatch is beyond the expectations for operators of smaller systems. A new algorithm is proposed in this paper to approximately solve the real-time dispatch optimization problem for a generic IES containing an on-site cogeneration system subject to random outages, limited curtailment opportunities, an intermittent renewable electricity source, and thermal storage. An example demonstrates how this algorithm can be used in simulation to estimate the value of IES components.

  12. Systems Studies

    SciTech Connect (OSTI)

    Graham, R.L.

    1998-03-17

    The Systems Studies Activity had two objectives: (1) to investigate nontechnical barriers to the deployment of biomass production and supply systems and (2) to enhance and extend existing systems models of bioenergy supply and use. For the first objective, the Activity focused on existing bioenergy markets. Four projects were undertaken: a comparative analysis of bioenergy in Sweden and Austria; a one-day workshop on nontechnical barriers jointly supported by the Production Systems Activity; the development and testing of a framework for analyzing barriers and drivers to bioenergy markets; and surveys of wood pellet users in Sweden, Austria and the US. For the second objective, two projects were undertaken. First, the Activity worked with the Integrated BioEnergy Systems (TBS) Activity of TEA Bioenergy Task XIII to enhance the BioEnergy Assessment Model (BEAM). This model is documented in the final report of the IBS Activity. The Systems Studies Activity contributed to enhancing the feedstock portion of the model by developing a coherent set of willow, poplar, and switchgrass production modules relevant to both the US and the UK. The Activity also developed a pretreatment module for switchgrass. Second, the Activity sponsored a three-day workshop on modeling bioenergy systems with the objectives of providing an overview of the types of models used to evaluate bioenergy and promoting communication among bioenergy modelers. There were nine guest speakers addressing different types of models used to evaluate different aspects of bioenergy, ranging from technoeconomic models based on the ASPEN software to linear programming models to develop feedstock supply curves for the US. The papers from this workshop have been submitted to Biomass and Bioenergy and are under editorial review.

  13. Toward a new metric for ranking high performance computing systems.

    Office of Scientific and Technical Information (OSTI)

    (Technical Report) | SciTech Connect Toward a new metric for ranking high performance computing systems. Citation Details In-Document Search Title: Toward a new metric for ranking high performance computing systems. The High Performance Linpack (HPL), or Top 500, benchmark [1] is the most widely recognized and discussed metric for ranking high performance computing systems. However, HPL is increasingly unreliable as a true measure of system performance for a growing collection of important

  14. Computerized Accident Incident Reporting System | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Computerized Accident Incident Reporting System Computerized Accident Incident Reporting System CAIRS Database The Computerized Accident/Incident Reporting System is a database used to collect and analyze DOE and DOE contractor reports of injuries, illnesses, and other accidents that occur during DOE operations. CAIRS is a Government computer system and, as such, has security requirements that must be followed. Access to the database is open to DOE and DOE contractors. Additional information

  15. Pollution Prevention Tracking and Reporting System | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Pollution Prevention Tracking and Reporting System Pollution Prevention Tracking and Reporting System Welcome to the Department of Energy's Pollution Prevention Tracking and Reporting System (PPTRS). DOE uses this system to collect information about, and assess the performance of, the Department's efforts in pollution prevention, sustainable acquisition, and recycling. DATA ENTRY: PPTRS will be open for data entry from October 1, 2013, through November 22, 2013. Click here to enter the PPTRS. To

  16. Extraterrestrial Materials: The Role of Synchrotron Radiation Analyses in the Study of Our Solar System

    ScienceCinema (OSTI)

    Sutton, Stephen R. [University of Chicago, Chicago, Illinois, United States

    2010-01-08

    Sample-return missions and natural collection processes have provided us with a surprisingly extensive collection of matter from Solar System bodies other than the Earth. These collections include samples from the Moon, Mars, asteroids, interplanetary dust, and, recently, from the Sun (solar wind) and a comet. This presentation will describe some of these materials, how they were collected, and what we have learned from them. Synchrotron radiation analyses of these materials are playing an increasingly valuable role in unraveling the histories and properities of the parent Solar System bodies.

  17. Microsoft PowerPoint - 4A Craig Benson

    Office of Environmental Management (EM)

    Liners and Covers: Field Performance & Life Expectancy Craig H. Benson, PhD, PE, NAE Wisconsin Distinguished Professor University of Wisconsin-Madison Interagency Steering Committee on Performance and Risk Assessment Community of Practice Annual Technical Exchange Meeting 11-12 December 2014 Las Vegas, Nevada, USA Covers & Waste Containment Waste Groundwater Native soil Leachate storage pond Groundwater monitoring well Rainwater retention pond Gas vent or collection well Leachate

  18. Analytical Services Management System

    Energy Science and Technology Software Center (OSTI)

    2005-03-30

    Analytical Services Management System (ASMS) provides sample management services. Sample management includes sample planning for analytical requests, sample tracking for shipping and receiving by the laboratory, receipt of the analytical data deliverable, processing the deliverable and payment of the laboratory conducting the analyses. ASMS is a web based application that provides the ability to manage these activities at multiple locations for different customers. ASMS provides for the assignment of single to multiple samples for standardmore »chemical and radiochemical analyses. ASMS is a flexible system which allows the users to request analyses by line item code. Line item codes are selected based on the Basic Ordering Agreement (BOA) format for contracting with participating laboratories. ASMS also allows contracting with non-BOA laboratories using a similar line item code contracting format for their services. ASMS allows sample and analysis tracking from sample planning and collection in the field through sample shipment, laboratory sample receipt, laboratory analysis and submittal of the requested analyses, electronic data transfer, and payment of the laboratories for the completed analyses. The software when in operation contains business sensitive material that is used as a principal portion of the Kaiser Analytical Management Services business model. The software version provided is the most recent version, however the copy of the application does not contain business sensitive data from the associated Oracle tables such as contract information or price per line item code.« less

  19. Impact of geothermal technology improvements on royalty collections on federal lands: Volume II: Appendices

    SciTech Connect (OSTI)

    Not Available

    1988-10-01

    This volume contains the appendices for the ''Impact of Geothermal Technology Improvements on Royalty Collections on Federal Lands, Final Report, Volume I.'' The material in this volume supports the conclusions presented in Volume I and details each Known Geothermal Resource Area's (KGRA's) royalty estimation. Appendix A details the physical characteristics of each KGRA considered in Volume I. Appendix B supplies summary narratives on each state which has a KGRA. The information presented in Appendix C shows the geothermal power plant area proxies chosen for each KGRA considered within the report. It also provides data ranges which fit into the IMGEO model for electric energy cost estimates. Appendix D provides detailed cost information from the IMGEO model if no Geothermal Program RandD goals were completed beyond 1987 and if all the RandD goals were completed by the year 2000. This appendix gives an overall electric cost and major system costs, which add up to the overall electric cost. Appendix E supplies information for avoided cost projections for each state involved in the study that were used in the IMGEO model run to determine at what cost/kWh a 50 MWe plant could come on line. Appendix F supplies the code used in the determination of royalty income, as well as, tabled results of the royalty runs (detailed in Appendix G). The tabled results show royalty incomes, assuming a 10% discount rate, with and without RandD and with and without a $0.01/kWh transmission cost. Individual data sheets for each KGRA royalty income run are presented in Appendix G.

  20. Concurrent Collections (CnC): A new approach to parallel programming

    ScienceCinema (OSTI)

    None

    2011-10-06

    A common approach in designing parallel languages is to provide some high level handles to manipulate the use of the parallel platform. This exposes some aspects of the target platform, for example, shared vs. distributed memory. It may expose some but not all types of parallelism, for example, data parallelism but not task parallelism. This approach must find a balance between the desire to provide a simple view for the domain expert and provide sufficient power for tuning. This is hard for any given architecture and harder if the language is to apply to a range of architectures. Either simplicity or power is lost. Instead of viewing the language design problem as one of providing the programmer with high level handles, we view the problem as one of designing an interface. On one side of this interface is the programmer (domain expert) who knows the application but needs no knowledge of any aspects of the platform. On the other side of the interface is the performance expert (programmer or program) who demands maximal flexibility for optimizing the mapping to a wide range of target platforms (parallel / serial, shared / distributed, homogeneous / heterogeneous, etc.) but needs no knowledge of the domain. Concurrent Collections (CnC) is based on this separation of concerns. The talk will present CnC and its benefits. About the speaker Kathleen Knobe has focused throughout her career on parallelism especially compiler technology, runtime system design and language design. She worked at Compass (aka Massachusetts Computer Associates) from 1980 to 1991 designing compilers for a wide range of parallel platforms for Thinking Machines, MasPar, Alliant, Numerix, and several government projects. In 1991 she decided to finish her education. After graduating from MIT in 1997, she joined Digital Equipment?s Cambridge Research Lab (CRL). She stayed through the DEC/Compaq/HP mergers and when CRL was acquired and absorbed by Intel. She currently works in the Software and Services Group / Technology Pathfinding and Innovation.

  1. Assembly for collecting samples for purposes of identification or analysis and method of use

    DOE Patents [OSTI]

    Thompson, Cyril V. (Knoxville, TN) [Knoxville, TN; Smith, Rob R. (Knoxville, TN) [Knoxville, TN

    2010-02-02

    An assembly and an associated method for collecting a sample of material desired to be characterized with diagnostic equipment includes or utilizes an elongated member having a proximal end with which the assembly is manipulated by a user and a distal end. In addition, a collection tip which is capable of being placed into contact with the material to be characterized is supported upon the distal end. The collection tip includes a body of chemically-inert porous material for binding a sample of material when the tip is placed into contact with the material and thereby holds the sample of material for subsequent introduction to the diagnostic equipment.

  2. 3-Year Renewal Request of OMB 1910-1800, Security, Information Collections

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    | Department of Energy 3-Year Renewal Request of OMB 1910-1800, Security, Information Collections 3-Year Renewal Request of OMB 1910-1800, Security, Information Collections Following are the collection instruments for your viewing. DOE F 5631.34, Data Report on Spouse/Cohabitant Security Incident Notification Report and Report of Preliminary Security Incident/Infraction (DOE F 471.1 and DOE F 5639.3) DOE F 5631.20, Request for Visitor Access Approval DOE Form 5631.18, Security

  3. Custody transfer enhanced by electronic billing system

    SciTech Connect (OSTI)

    Knox, R.M.

    1986-10-20

    Transcontinental Gas Pipe Line (TGPL) Corp. engineers have developed an electronic billing system for custody transfer that can reduce the cost of doing business and improve the accuracy of transfer measurements. The system accurately measures gas flow and quality, transmits gas data to a central facility, provides a capability to review the collected data, prepares bills based upon these data, and reduces staffing associated with the data collection and billing process. On-line flow computers are keys to this electronic billing system. These computers, referred to as remote terminal units (RTU's), are currently in service at TGPL at more than 30 locations with 30 more locations due to be on-line within 6 months and an additional 40 locations due within 15 months. These RTU's will be obtaining gas data from metering stations located in New York, New Jersey, Pennsylvania, Maryland, Virginia, North Carolina, Georgia, Louisiana, and Texas.

  4. The Energy DataBus: NREL's Open-Source Application for Large-Scale Energy Data Collection and Analysis

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    NRELs Energy DataBus is used for tracking and analyzing energy use on its own campus. The system is applicable to other facilitiesincluding anything from a single building to a large military base or college campusor for other energy data management needs. Managing and minimizing energy consumption on a large campus is usually a difficult task for facility managers: There may be hundreds of energy meters spread across a campus, and the meter data are often recorded by hand. Even when data are captured electronically, there may be measurement issues or time periods that may not coincide. Making sense of this limited and often confusing data can be a challenge that makes the assessment of building performance a struggle for many facility managers. The Energy DataBus software was developed by NREL to address these issues on its own campus, but with an eye toward offering its software solutions to other facilities. Key features include the software's ability to store large amounts of data collected at high frequenciesNREL collects some of its energy data every secondand rich functionality to integrate this wide variety of data into a single database [copied from http://en.openei.org/wiki/NREL_Energy_DataBus].

  5. Epizootic ulcerative syndrome caused by Aphanomyces invadans in captive bullseye snakehead Channa marulius collected from south Florida, USA

    SciTech Connect (OSTI)

    Saylor, Ryan; Miller, Debra; Vandersea, Mark; Bevelhimer, Mark S; Schofield, Pamela; Bennett, Wayne

    2010-02-01

    Epizootic ulcerative syndrome (EUS) caused by the oomycete Aphanomyces invadans is an invasive, opportunistic disease of both freshwater and estuarine fishes. Originally documented as the cause of mycotic granulomatosis of ornamental fishes in Japan and as the cause of EUS of fishes in southeast Asia and Australia, this pathogen is also present in estuaries and freshwater bodies of the Atlantic and gulf coasts of the USA. We describe a mass mortality event of 343 captive juvenile bullseye snakehead Channa marulius collected from freshwater canals in Miami-Dade County, Florida. Clinical signs appeared within the first 2 d of captivity and included petechiae, ulceration, erratic swimming, and inappetence. Histological examination revealed hyphae invading from the skin lesions deep into the musculature and internal organs. Species identification was confirmed using a species-specific PCR assay. Despite therapeutic attempts, 100% mortality occurred. This represents the first documented case of EUS in bullseye snakehead fish collected from waters in the USA. Future investigation of the distribution and prevalence of A. invadans within the bullseye snakehead range in south Florida may give insight into this pathogen-host system.

  6. The Energy DataBus: NREL's Open-Source Application for Large-Scale Energy Data Collection and Analysis

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    NREL’s Energy DataBus is used for tracking and analyzing energy use on its own campus. The system is applicable to other facilities—including anything from a single building to a large military base or college campus—or for other energy data management needs. Managing and minimizing energy consumption on a large campus is usually a difficult task for facility managers: There may be hundreds of energy meters spread across a campus, and the meter data are often recorded by hand. Even when data are captured electronically, there may be measurement issues or time periods that may not coincide. Making sense of this limited and often confusing data can be a challenge that makes the assessment of building performance a struggle for many facility managers. The Energy DataBus software was developed by NREL to address these issues on its own campus, but with an eye toward offering its software solutions to other facilities. Key features include the software's ability to store large amounts of data collected at high frequencies—NREL collects some of its energy data every second—and rich functionality to integrate this wide variety of data into a single database [copied from http://en.openei.org/wiki/NREL_Energy_DataBus].

  7. Classified Information Systems Security Manual

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    1999-08-03

    This Manual provides requirements and implementation instructions for the graded protection of the confidentiality, integrity, and availability of information processed on all automated information systems used to collect, create, process, transmit, store, and disseminate classified information by, or on behalf of, the Department of Energy (DOE). DOE N 205.4 cancels Chapter III section 8, Incident Reporting, and DOE N 205.3 cancels Chapter VI, paragraph 4j(2), 4j(6); and Chapter VII, paragraph 12a(2)(a). Cancels: DOE M 5639.6A-1. Canceled by DOE M 205.1-4.

  8. Gas Main Sensor and Communications Network System

    SciTech Connect (OSTI)

    Hagen Schempf

    2006-05-31

    Automatika, Inc. was contracted by the Department of Energy (DOE) and with co-funding from the Northeast Gas Association (NGA), to develop an in-pipe natural gas prototype measurement and wireless communications system for assessing and monitoring distribution networks. This projected was completed in April 2006, and culminated in the installation of more than 2 dozen GasNet nodes in both low- and high-pressure cast-iron and steel mains owned by multiple utilities in the northeastern US. Utilities are currently logging data (off-line) and monitoring data in real time from single and multiple networked sensors over cellular networks and collecting data using wireless bluetooth PDA systems. The system was designed to be modular, using in-pipe sensor-wands capable of measuring, flow, pressure, temperature, water-content and vibration. Internal antennae allowed for the use of the pipe-internals as a waveguide for setting up a sensor network to collect data from multiple nodes simultaneously. Sensor nodes were designed to be installed with low- and no-blow techniques and tools. Using a multi-drop bus technique with a custom protocol, all electronics were designed to be buriable and allow for on-board data-collection (SD-card), wireless relaying and cellular network forwarding. Installation options afforded by the design included direct-burial and external polemounted variants. Power was provided by one or more batteries, direct AC-power (Class I Div.2) and solar-array. The utilities are currently in a data-collection phase and intend to use the collected (and processed) data to make capital improvement decisions, compare it to Stoner model predictions and evaluate the use of such a system for future expansion, technology-improvement and commercialization starting later in 2006.

  9. Systems Engineering

    Broader source: Energy.gov [DOE]

    Project objectives: to create an interactive, physics based, systems analysis tool for geothermal energy development that will: Identify points of attack to maximize efforts and investment dollars; Identify the parameter space where geothermal energy production is physically and economically viable; Provide a platform for public education and interaction.

  10. Situational Awareness for Strategic Leadership (part of CORE system)

    Energy Science and Technology Software Center (OSTI)

    2009-10-02

    System allows for information to be collected, shared, and commented on by a large group of users. The interaction with the system is independent of time and location, so that input of information and conversations can occur more naturally as they currently do with email.

  11. Directory of Energy Data Collection Forms: Forms in use as of October 1996

    SciTech Connect (OSTI)

    1996-12-01

    This is the twentieth edition of the Directory of Energy Collection Data Forms, an authoritative listing of selected public use forms currently used as basic energy information gathering tools by the Department of Energy.

  12. Collection from Current and Former Employees for Indebtedness to the United States

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2003-09-26

    To prescribe the policy and procedures for collecting debts owed by current and former Department of Energy (DOE) and National Nuclear Security Administration (NNSA) employees to the United States Government. Supersedes DOE 2200.2B.

  13. Collective properties of the final state in processes involving the production of hadron jets

    SciTech Connect (OSTI)

    Okorokov, V. A. Ponosov, A. K.

    2013-10-15

    Experimental results obtained by studying soft hadron jets in pion-proton and pion-nucleus reactions at intermediate energies with the aid of traditional collective variables are presented. Analytic approximations that describe, at a qualitative level, the dependences of collective parameters on the energy and multiplicity are proposed. Estimates obtained for strong coupling constant by studying collective variables are in reasonable agreement with its world-average value and with the results extracted by using different methods. The behavior of traditional collective variables as functions of the multiplicity in various interactions makes it possible to obtain a universal estimate for the lower boundary of the region of experimental manifestations of jets in multiparticle-production processes.

  14. Proposed Agency Information Collection: Federal Register Notice Volume 76, No. 195- Oct. 7, 2011

    Broader source: Energy.gov [DOE]

    The Department of Energy (DOE) invites public comment on DOEs request the Office of Management and Budget (OMB) to extend for three years the emergency Information Collection Request Title: OE...

  15. Venice Park landfill: Working with the community

    SciTech Connect (OSTI)

    McAdams, C.L.

    1993-09-01

    Venice Park landfill was one of the first sites to be permitted under Michigan's proposed Public Act 641. PA 641 essentially changed the rules and regulations for landfills from the simple design of digging a hole and filling it. It also upgraded standards to those that are more sophisticated, including liners, leachate collection systems, and gas extraction systems. In 1992, methane gas from the landfill was collected into wells drilled into the trash varying in depth from 30-50 feet in depth. A vacuum pulls the gas from the trash into the wells, then through a piping system. The landfill uses about 80-100 kilowatts in-house. The remainder of the gas is sold to Consumers Power Co. which uses landfill gas to supply power to homes.

  16. Develop NREL Center for Low Temperature Research/Project Data Collection |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Department of Energy Develop NREL Center for Low Temperature Research/Project Data Collection Develop NREL Center for Low Temperature Research/Project Data Collection Project objective: Low-Temperature Geothermal (LTGT) represents a huge; underutilized resource of renewable energy in the United States.; This project will accelerate the commercial application of these resources. PDF icon low_williams_nrel_center.pdf More Documents & Publications Novel Energy Conversion Equipment for Low

  17. Low-energy collective modes of deformed superfluid nuclei within the

    Office of Scientific and Technical Information (OSTI)

    finite-amplitude method (Journal Article) | SciTech Connect Low-energy collective modes of deformed superfluid nuclei within the finite-amplitude method Citation Details In-Document Search Title: Low-energy collective modes of deformed superfluid nuclei within the finite-amplitude method Authors: Hinohara, Nobuo ; Kortelainen, Markus ; Nazarewicz, Witold Publication Date: 2013-06-17 OSTI Identifier: 1103819 Type: Publisher's Accepted Manuscript Journal Name: Physical Review C Additional

  18. Electron density magnification of the collective spin-orbit field in

    Office of Scientific and Technical Information (OSTI)

    quantum wells (Journal Article) | SciTech Connect Electron density magnification of the collective spin-orbit field in quantum wells Citation Details In-Document Search This content will become publicly available on September 27, 2016 Title: Electron density magnification of the collective spin-orbit field in quantum wells Authors: Baboux, F. ; Perez, F. ; Ullrich, C. A. ; Karczewski, G. ; Wojtowicz, T. Publication Date: 2015-09-28 OSTI Identifier: 1222050 Grant/Contract Number:

  19. State Heating Oil and Propane Program Expansion of Propane Data Collection

    U.S. Energy Information Administration (EIA) Indexed Site

    State Heating Oil and Propane Program Expansion of Propane Data Collection Marcela Rourk April 14, 2014 | Washington, DC Key Topics Marcela Rourk, Washington, DC April 14, 2014 2 * Overview and history of State Heating Oil and Propane Program (SHOPP) * Expansion of propane data collection * What is expected of SEOs that participate? * Benefits of participation What is SHOPP? Marcela Rourk, Washington, DC April 14, 2014 3 * State Heating Oil and Propane Program (SHOPP) - cooperative data

  20. Seismic safety margins research program. Phase I. Final report: plant/site selection and data collection (Project I)

    SciTech Connect (OSTI)

    Chuang, T. Y.

    1981-05-01

    Project I of Phase I of the Seismic Safety Margins Research Program (SSMRP) comprised two parts: the selection of a representative nuclear power plant/site for study in Phase I and the collection of data needed by the other SSMRP projects. Unit 1 of the Zion Nuclear Power Plant in Zion, Illinois, was selected for the SSMRP Phase I studies. The Zion plant and its site were found to be reasonably representative of operating and future plants with regard to its nuclear steam supply system; the type of containment structure (prestressed concrete); its electrical capacity (1100 MWe); its location (the Midwest); the peak seismic accelaration used for design (0.17g); and the properties of the underlying soil (the low-strain shear-wave velocity is 1650 ft/s in a 50- to 100-ft-thick layer of soil overlying sedimentary bedrock).