Powered by Deep Web Technologies
Note: This page contains sample records for the topic "kw ground mounted" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Department of Veterans Affairs, FONSI - Ground mounted solar...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Ground mounted solar photovoltaic power at San Joaquin National Cemetery Department of Veterans Affairs, FONSI - Ground mounted solar photovoltaic power at San Joaquin National...

2

Department of Veterans Affairs, FONSI - Ground mounted solar photovoltaic  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Ground mounted solar Ground mounted solar photovoltaic power at San Joaquin National Cemetery Department of Veterans Affairs, FONSI - Ground mounted solar photovoltaic power at San Joaquin National Cemetery An Environmental Assessment (EA) has been prepared under the direction of an interdisciplinary team analyzing theproposed construction of a Photovoltaic System at the San Joaquin National Cemetery (SNC) in San Joaquin,Calofornia. CX rulemaking files More Documents & Publications Department of Veterans Affairs, FONSI - Rooftop solar PV power at Calverton National Cemetery Department of Energy Technical Support Document National Environmental Policy Act Implementing Procedures Supplement to Notice of Proposed Rulemaking Proposed Changes and Supplemental Supporting Basis

3

Pattern Of Shallow Ground Water Flow At Mount Princeton Hot Springs,  

Open Energy Info (EERE)

Pattern Of Shallow Ground Water Flow At Mount Princeton Hot Springs, Pattern Of Shallow Ground Water Flow At Mount Princeton Hot Springs, Colorado, Using Geoelectrical Methods Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Pattern Of Shallow Ground Water Flow At Mount Princeton Hot Springs, Colorado, Using Geoelectrical Methods Details Activities (2) Areas (1) Regions (0) Abstract: In geothermal fields, open faults and fractures often act as high permeability pathways bringing hydrothermal fluids to the surface from deep reservoirs. The Mount Princeton area, in south-central Colorado, is an area that has an active geothermal system related to faulting and is therefore a suitable natural laboratory to test geophysical methods. The Sawatch range-front normal fault bordering the half-graben of the Upper Arkansas

4

Ground-Based and Airborne (PMS 2-D Probe Canister-Mounted) 183 GHz Water  

NLE Websites -- All DOE Office Websites (Extended Search)

Ground-Based and Airborne (PMS 2-D Probe Canister-Mounted) 183 GHz Water Ground-Based and Airborne (PMS 2-D Probe Canister-Mounted) 183 GHz Water Vapor Radiometer Pazmany, Andrew ProSensing Inc. Category: Instruments ProSensing Inc. has developed a G-band (183 GHz, 1.5 mm wavelength) water vapor radiometer (GVR) for the measurement of low concentrations of atmospheric water vapor and liquid water. The instrument's precipitable water vapor measurement precision is approximately 0.01 mm in dry (<2 mm vapor column) conditions. The ground-based version of the instrument was first deployed at ProSensing's facility in Amherst, MA in February 2005, then at the North Slope of Alaska DOE ARM site in Barrow AK in April 2005, where it has been continuously operating since. An airborne version, designed to operate from a standard PMS 2-D probe canister, is now being

5

Land use requirements for ground-mounted solar power facilities. | OpenEI  

Open Energy Info (EERE)

Land use requirements for ground-mounted solar power facilities. Land use requirements for ground-mounted solar power facilities. Dataset Summary Description This dataset is part of a larger internal dataset at the National Renewable Energy Laboratory (NREL) that explores various characteristics of large solar electric (both PV and CSP) facilities around the United States. This dataset focuses on the land use characteristics for solar facilities that are either under construction or currently in operation. Source Land-Use Requirements for Solar Power Plants in the United States Date Released June 25th, 2013 (5 months ago) Date Updated Unknown Keywords acres area average concentrating solar power csp Density electric hectares km2 land land requirements land use land-use mean photovoltaic photovoltaics PV solar statistics Data application/vnd.openxmlformats-officedocument.spreadsheetml.sheet icon Master Solar Land Use Spreadsheet (xlsx, 1.5 MiB)

6

Earthquake Experience Data on Anchored, Ground-Mounted Vertical Storage Tanks  

Science Conference Proceedings (OSTI)

Earthquake experience data indicate that anchored, vertical storage tanks similar in structure to those used in nuclear power plant safety systems can survive greater ground motion than accounted for in most nuclear plant designs. Comparison of design parameters for nuclear and nonnuclear storage tanks confirmed the applicability of earthquake experience data to demonstrate the seismic adequacy of nuclear plant storage tanks.

1989-03-17T23:59:59.000Z

7

A validation of ground penetrating radar for reconstructing the internal structure of a rock glacier: Mount Mestas, Colorado, USA  

E-Print Network (OSTI)

Rock glaciers are dynamic landforms and, as such, exhibit interesting and welldeveloped structural features, which translate to surface morphology in the form of ridges and furrows. These distinguishing features have led researchers to study the physics behind the movement and internal deformation of rock glaciers. For years researchers had no access to the internal makeup of rock glaciers. Thus, proposed models and discussion have been based on theoretical concepts of electromagnetic (EM) wave propogation. With the application of ground penetrating radar (GPR) to provide a view of the interior structure of a rock glacier, researchers had “real” data to verify their models. However, no comparison has been made between a GPR profile and an actual cross-section of a rock glacier. The purpose of this thesis is to validate the fidelity of GPR in showing the actual structure of a rock glacier. A trench that was excavated through the toe of a rock glacier on Mount Mestas in south central Colorado provided a view of the actual structure of the landform. The structure in the trench was compared with GPR and EM data. The GPR study was conducted using a PulsEKKOTM 100A subsurface imaging radar with 25, 50, and 100 MHz antennas, to detect dielectric contrasts within the rock glacier. A frequency domain EM34 by Geonics LtdTM was also used to supplement the GPR data by measuring the rock glacier’s conductivity at various depths. This thesis proved, by utilizing statistics, that GPR is a useful tool in visualizing the interior structure of rock glaciers. The 100 MHz antennas clearly show small scale reflection horizons caused by changes in clast orientation and subsurface material composition. These events coincide with structures seen in the trench. Individual clasts greater than 0.375 m were also recognized as point sources in the GPR profiles. Large continuous bedding layers were observed with the 25 and 50 MHz antennas, which reflect the structure seen in the trench. A large scale thrust fault was also located with the GPR. However, this was not visible in the panoramic photograph because the fault occurs below the base of the trench.

Jorgensen, William Revis

2007-05-01T23:59:59.000Z

8

Photovoltaic module mounting system  

SciTech Connect

A solar array mounting system having unique installation, load distribution, and grounding features, and which is adaptable for mounting solar panels having no external frame. The solar array mounting system includes flexible, pedestal-style feet and structural links connected in a grid formation on the mounting surface. The photovoltaic modules are secured in place via the use of attachment clamps that grip the edge of the typically glass substrate. The panel mounting clamps are then held in place by tilt brackets and/or mid-link brackets that provide fixation for the clamps and align the solar panels at a tilt to the horizontal mounting surface. The tilt brackets are held in place atop the flexible feet and connected link members thus creating a complete mounting structure.

Miros, Robert H. J. (Fairfax, CA); Mittan, Margaret Birmingham (Oakland, CA); Seery, Martin N. (San Rafael, CA); Holland, Rodney H. (Novato, CA)

2012-04-17T23:59:59.000Z

9

Photovoltaic module mounting system  

SciTech Connect

A solar array mounting system having unique installation, load distribution, and grounding features, and which is adaptable for mounting solar panels having no external frame. The solar array mounting system includes flexible, pedestal-style feet and structural links connected in a grid formation on the mounting surface. The photovoltaic modules are secured in place via the use of attachment clamps that grip the edge of the typically glass substrate. The panel mounting clamps are then held in place by tilt brackets and/or mid-link brackets that provide fixation for the clamps and align the solar panels at a tilt to the horizontal mounting surface. The tilt brackets are held in place atop the flexible feet and connected link members thus creating a complete mounting structure.

Miros, Robert H. J.; Mittan, Margaret Birmingham; Seery, Martin N; Holland, Rodney H

2012-09-18T23:59:59.000Z

10

Optoelectronic Mounting Structure  

DOE Patents (OSTI)

An optoelectronic mounting structure is provided that may be used in conjunction with an optical transmitter, receiver or transceiver module. The mounting structure may be a flexible printed circuit board. Thermal vias or heat pipes in the head region may transmit heat from the mounting structure to the heat spreader. The heat spreader may provide mechanical rigidity or stiffness to the heat region. In another embodiment, an electrical contact and ground plane may pass along a surface of the head region so as to provide an electrical contact path to the optoelectronic devices and limit electromagnetic interference. In yet another embodiment, a window may be formed in the head region of the mounting structure so as to provide access to the heat spreader. Optoelectronic devices may be adapted to the heat spreader in such a manner that the devices are accessible through the window in the mounting structure.

Anderson, Gene R. (Albuquerque, NM); Armendariz, Marcelino G. (Albuquerque, NM); Baca, Johnny R. F. (Albuquerque, NM); Bryan, Robert P. (Albuquerque, NM); Carson, Richard F. (Albuquerque, NM); Chu, Dahwey (Albuquerque, NM); Duckett, III, Edwin B. (Albuquerque, NM); McCormick, Frederick B. (Albuquerque, NM); Peterson, David W. (Sandia Park, NM); Peterson, Gary D. (Albuquerque, NM); Reber, Cathleen A. (Corrales, NM); Reysen, Bill H. (Lafayette, CO)

2004-10-05T23:59:59.000Z

11

Plastic Mounts  

Science Conference Proceedings (OSTI)

Table 3   Typical properties of plastics suitable for metallographic mounts...metals is in the range 1â??3 Ã? 10 -5 mm/mm/°C. (c) Wood-filled grade, preferably with low filler content. (d) A liquid epoxy resin with an aliphatic amine hardener. (e) Depends on the curing schedule;

12

Plasma Screen Floating Mount  

Engineers at the Savannah River National Laboratory (SRNL) have invented a new mounting system for flat panel video technology.  The plasma screen floating mount is a mounting system proven to eliminate vibration and dampen shock for mobile uses of ...

13

SOFCSOFC (10kW(10kW )) Stack Stack ( )  

E-Print Network (OSTI)

& Mitsubishi (band ) 150 kW module Rolls-Royce () 100kW SOFC TOTO, Kyushu () 20kW stack wet process #12;2 SOFC () Mitsubishi Heavy Ind. § SIS § 250kW § 55% Rolls-Royce § SIS § 250kW (micro GT-SOFC) § 53% (125 kW ) Tokyo Gas § SIS § kW (5kW ) / #12

Hong, Deog Ki

14

Magnetic core mounting system  

DOE Patents (OSTI)

A mounting apparatus for an electromagnetic device such as a transformer of inductor includes a generally planar metallic plate as a first heat sink, and a metallic mounting cup as a second heat sink. The mounting cup includes a cavity configured to receive the electromagnetic device, the cavity being defined by a base, and an axially-extending annular sidewall extending from the base to a flange portion of the mounting cup. The mounting cup includes first and second passages for allowing the leads of first and second windings of the electromagnetic device to be routed out of the cavity. The cavity is filled with a polyurethane potting resin, and the mounting cup, including the potted electromagnetic device, is mounted to the plate heat sink using fasteners. The mounting cup, which surrounds the electromagnetic device, in combination with the potting resin provides improved thermal transfer to the plate heat sink, as well as providing resistance to vibration and shocks.

Ronning, Jeffrey J. (Fishers, IN)

2002-01-01T23:59:59.000Z

15

Timothy L. Mounts Award  

Science Conference Proceedings (OSTI)

Recognizing research relating to the science and technology of edible oils: basic or applied in nature. Eligibility, Nominations Timothy L. Mounts Award Timothy L. Mounts Award  Recognizing research relating to the science and technolo

16

Test #3, natural gas, HRR=400 KW  

Science Conference Proceedings (OSTI)

*. Bookmark and Share. Reduced Scale Enclosure Fire Images (NIST TN1483). Test #3, Natural Gas, HRR-400 kW.

2012-03-20T23:59:59.000Z

17

Mounting for ceramic scroll  

SciTech Connect

A mounting for a ceramic scroll on a metal engine block of a gas turbine engine includes a first ceramic ring and a pair of cross key connections between the first ceramic ring, the ceramic scroll, and the engine block. The cross key connections support the scroll on the engine block independent of relative radial thermal growth and for bodily movement toward an annular mounting shoulder on the engine. The scroll has an uninterrupted annular shoulder facing the mounting shoulder on the engine block. A second ceramic ring is captured between mounting shoulder and the uninterrupted shoulder on the scroll when the latter is bodily shifted toward the mouting shoulder to define a gas seal between the scroll and the engine block.

Petty, Jack D. (Indianapolis, IN)

1993-01-01T23:59:59.000Z

18

The Mount Bachelor Observatory  

Science Conference Proceedings (OSTI)

The Mount Bachelor Observatory, is an EPRI-sponsored high-elevation mountaintop air quality sampling station that provides an ideal location for assessing the origin and impact of long-range transport of critical contaminantssuch as mercury (Hg), ozone (O3), nitrogen oxides (NOx), and particulate matteron the atmospheric composition along North America's West Coast.

2009-12-04T23:59:59.000Z

19

Manipulator mounted transfer platform  

Science Conference Proceedings (OSTI)

The patent describes in a manipulator system for use in hazardous environments including a manipulator adapted for reciprocal movement upon a guide device, a transfer platform. It comprises: a bed frame defining a generally horizontal bed projecting outwardly from the manipulator; and frame mounting means securing the bed frame to the manipulator in a generally cantilevered fashion, thereby essentially minimizing the structure necessary to support the platform outwardly of the manipulator while enhancing operator visibility of the platform and the manipulator during use of the manipulator system.

Dobbins, J.C.; Hoover, M.A.; May, K.W.; Ross, M.J.

1990-01-23T23:59:59.000Z

20

DESIGN STUDY OF A NUCLEAR POWER PLANT FOR 100-KW ELECTRIC AND 400-KW HEAT CAPACITY  

SciTech Connect

A conceptional design study was made of a lowpower ''package'' reactor plant for the production of 100 kw of electrical power and 400 kw of heat at remote Arctic installations. The power plant steam generator is proposed to be an unmanned, heterogeneous, boilingtype reactor capable of continuous operation for extended periods. The design is based on data derived from experiments with boiling-type reactors conducted by Argorne at the Reactor Testing Station, Arco, Idaho.

Treshow, M.; Snider, A.R.; Shaftman, D.H.

1955-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "kw ground mounted" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

CX-005603: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

and 1 ground-mount system. Rooftop units will be located at 4814 Seton Drive (132 kilowatts (kW)), 4815 Seton Drive (105kW), and 4810 Seton Drive (54kW). Ground-mount unit will...

22

Surficial Extent And Conceptual Model Of Hydrothermal System At Mount  

Open Energy Info (EERE)

Surficial Extent And Conceptual Model Of Hydrothermal System At Mount Surficial Extent And Conceptual Model Of Hydrothermal System At Mount Rainier, Washington Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Surficial Extent And Conceptual Model Of Hydrothermal System At Mount Rainier, Washington Details Activities (4) Areas (2) Regions (0) Abstract: A once massive hydrothermal system was disgorged from the summit of Mount Rainier in a highly destructive manner about 5000 years ago. Today, hydrothermal processes are depositing clayey alteration products that have the potential to reset the stage for similar events in the future. Areas of active hydrothermal alteration occur in three representative settings: 1. (1) An extensive area (greater than 12,000 m2) of heated ground and slightly acidic boiling-point fumaroles at 76-82°C at

23

Property:Incentive/WindResMaxKW | Open Energy Information  

Open Energy Info (EERE)

search Property Name IncentiveWindResMaxKW Property Type String Description The maximum installed residential wind capacity in kW that is eligible for a rebate. Ex: The maximum...

24

Property:Incentive/PVComDolKW | Open Energy Information  

Open Energy Info (EERE)

Name IncentivePVComDolKW Property Type String Description The amount per kW of installed capacity of a commercial PV system disbursed as an upfront incentive. Ex: MN's...

25

Property:Incentive/PVResDolKW | Open Energy Information  

Open Energy Info (EERE)

Name IncentivePVResDolKW Property Type String Description The amount per kW of installed capacity of a residential PV system disbursed as an upfront incentive. Ex: MD's...

26

Property:Incentive/WindComMaxKW | Open Energy Information  

Open Energy Info (EERE)

search Property Name IncentiveWindComMaxKW Property Type String Description The maximum installed commercial wind capacity in kW that is eligible for a rebate. This also applies...

27

Property:Incentive/PVComMaxKW | Open Energy Information  

Open Energy Info (EERE)

search Property Name IncentivePVComMaxKW Property Type String Description The maximum installed commercial PV capacity in kW that is eligible for a rebate. This also applies to...

28

Property:Incentive/PVResMaxKW | Open Energy Information  

Open Energy Info (EERE)

search Property Name IncentivePVResMaxKW Property Type String Description The maximum installed residential PV capacity in kW that is eligible for a rebate. CT's maximum...

29

Property:Incentive/WindResDolKW | Open Energy Information  

Open Energy Info (EERE)

Name IncentiveWindResDolKW Property Type String Description The amount per kW of installed capacity of a residential wind system disbursed as an upfront incentive. Ex:...

30

Property:Incentive/WindComDolKW | Open Energy Information  

Open Energy Info (EERE)

Name IncentiveWindComDolKW Property Type String Description The amount per kW of installed capacity of a commercial wind system disbursed as an upfront incentive. Ex: OR's...

31

Electro-optic component mounting device  

DOE Patents (OSTI)

A technique is provided for integrally mounting a device such as an electro-optic device in a transmission line to avoid series resonant effects. A center conductor of the transmission line has an aperture formed therein for receiving the device. The aperture splits the center conductor into two parallel sections on opposite sides of the device. For a waveguide application, the center conductor is surrounded by a conductive ground surface which is spaced apart from the center conductor with a dielectric material. One set of electrodes formed on the surface of the electro-optic device is directly connected to the center conductor and an electrode formed on the surface of the electro-optic device is directly connected to the conductive ground surface. The electrodes formed on the surface of the electro-optic device are formed on curved sections of the surface of the device to mate with correspondingly shaped electrodes on the conductor and ground surface to provide a uniform electric field across the electro-optic device. The center conductor includes a passage formed therein for passage of optical signals to an electro-optic device. 10 figs.

Gruchalla, M.E.

1994-09-13T23:59:59.000Z

32

Property:Incentive/PVPbiFitMaxKW | Open Energy Information  

Open Energy Info (EERE)

PVPbiFitMaxKW PVPbiFitMaxKW Jump to: navigation, search Property Name Incentive/PVPbiFitMaxKW Property Type String Description The maximum installed PV capacity in kW that is eligible for the PBI or FIT. Ex: We Energies' FIT maximum eligible PV system size is 100 kW. Format: 100.0 [1] References ↑ DSIRE Pages using the property "Incentive/PVPbiFitMaxKW" Showing 25 pages using this property. (previous 25) (next 25) A Alliant Energy (Wisconsin Power and Light) - Advanced Renewables Tariff (Wisconsin) + 20 + Ameren Missouri - Solar Renewable Energy Credits + 100 + Anaheim Public Utilities - PV Buydown Program (California) + 1000 + Austin Energy - Commercial PV Incentive Program (Texas) + 20 + Austin Energy - Value of Solar Residential Rate (Texas) + 20 +

33

VIBRATION DAMPING AND SHOCK MOUNT  

DOE Patents (OSTI)

A shock absorbing mount in which vibrations are damped by an interference fit between relatively movable parts of the mount is described. A pair of generally cup-shaped parts or members have skirt portions disposed in an oppositely facing nesting relationship with the skirt of one member frictionally engaging the skirt of the other. The outermost skirt may be slotted to provide spring-like segments which embrace the inner skirt for effecting the interference fit. Belleville washers between the members provide yieldable support for a load carried by the mount. When a resonant frequency of vibration forces acting upon the moumt attains a certain level the kinetic energy of these forces is absorbed by sliding friction between the parts. (AEC)

Stevens, D.J.; Forman, G.W.

1963-12-10T23:59:59.000Z

34

300kW Energy Storage Demonstration Project  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

kW Energy Storage Demonstration Project Technical Overview Presented at: Annual Doe Peer Review Meeting 2008 DOE Energy Storage & Power Electronics Research Programs By Ib I....

35

Apparatus for mounting a diode in a microwave circuit  

DOE Patents (OSTI)

Apparatus for mounting a diode in a microwave circuit for making electrical contact between the circuit and ground and for dissipation of heat between the diode and a heat sink. The diode, supported on a thermally and electrically conductive member, is resiliently pressed in electrical contact with the microwave circuit. A tapered collar on the member is elastically deformably wedged into a tapered aperture formed in a heat sink. The wedged collar tightens firmly around the member establishing good thermal and electrical conduction from the diode to the heat sink and ground. Disassembly is facilitated because of the elastically deformed collar.

Liu, Shing-gong (Princeton, NJ)

1976-07-27T23:59:59.000Z

36

MBO: The Mount Bachelor Observatory  

Science Conference Proceedings (OSTI)

Intercontinental transport of pollutants from Asia has an impact on the atmospheric composition and air quality along the west coast of North America, which in turn has important implications for U.S. air quality. The Mount Bachelor Observatory (MBO) is a high-elevation mountaintop atmospheric observatory, located approximately 120 miles east of Eugene on Oregon's Mt. Bachelor. It provides an ideal location for sampling the global atmosphere in order to assess the impact of Asian long-range transport (AL...

2008-12-23T23:59:59.000Z

37

Tower Design Load Verification on a 1-kW Wind Turbine: Preprint  

DOE Green Energy (OSTI)

Wind turbine testing at the National Wind Technology Center (NWTC) has been done to characterize both tower top loads and thrust loads for small wind turbines, which is part of an ongoing effort to model and predict small wind turbine behavior and the resulting stresses imposed on the supporting tower. To these ends, a 1-kW furling wind turbine mounted on a 10-meter tower was instrumented and monitored via a data acquisition system for nearly a year. This test was conducted to verify the design loads as predicted by the simple design equations provided in the draft revision of the International Electrotechnical Commission (IEC) Small Wind Turbine Safety Standard 61400-02 CDV (hereafter called ''the draft Standard''). Data were captured for several operating conditions covered by the draft Standard. This paper addresses the collected data and what conclusions can be made from it.

Prascher, D.; Huskey, A.

2004-11-01T23:59:59.000Z

38

Mounting support for a photovoltaic module  

DOE Patents (OSTI)

A mounting support for a photovoltaic module is described. The mounting support includes a foundation having an integrated wire-way ledge portion. A photovoltaic module support mechanism is coupled with the foundation.

Brandt, Gregory Michael; Barsun, Stephan K.; Coleman, Nathaniel T.; Zhou, Yin

2013-03-26T23:59:59.000Z

39

Holding fixture for metallographic mount polishing  

DOE Patents (OSTI)

A fixture for holding mounted specimens for polishing, having an arm; a body attached to one end of the arm, the body having at least one flange having an opening to accommodate a mounted specimen; and a means applying pressure against the outer surface of the mounted specimen to hold the specimen in contact with the polishing surface.

Barth, C.H.; Cramer, C.E.

1996-12-31T23:59:59.000Z

40

5-kW Solid Oxide Fuel Cell Case Study  

Science Conference Proceedings (OSTI)

This report chronicles, as a case study, a project in which an Acumentrics 5-kW solid oxide fuel cell was installed at Cuyahoga Valley National Park in Ohio.

2006-03-27T23:59:59.000Z

Note: This page contains sample records for the topic "kw ground mounted" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Bulb mounting of solar cell  

SciTech Connect

An energy converting assembly is provided for parasiting of light from a fluorescent light bulb utilizing a solar cell. The solar cell is mounted on a base member elongated in the dimension of elongation of the fluorescent bulb, and electrical interconnections to the cell are provided. A flexible sheet of opaque material having a flat white interior reflective surface surrounds the fluorescent bulb and reflects light emitted from the bulb back toward the bulb and the solar cell. The reflective sheet is tightly held in contact with the bottom of the bulb by adhesive, a tie strap, an external clip, or the like.

Thompson, M.E.

1983-04-05T23:59:59.000Z

42

SOLERAS - Solar Cooling Engineering Field Tests Project: Carrier Corporation. Fabrication, testing and installation report: 53 kW solar absorption cooling system  

DOE Green Energy (OSTI)

A 53 kW water cooled packaged solar absorption chiller was fabricated and tested. The generator shell and absorber shell had sight glasses added as a diagnostic device. The unit was modified so that a base suitable for mounting pumps, valves and associated piping was cantilevered from one end of the unit. The installation and start-up of the cooling system is outlined.

Not Available

1985-01-01T23:59:59.000Z

43

Nozzle and shroud assembly mounting structure  

DOE Patents (OSTI)

The present nozzle and shroud assembly mounting structure configuration increases component life and reduces maintenance by reducing internal stress between the mounting structure having a preestablished rate of thermal expansion and the nozzle and shroud assembly having a preestablished rate of thermal expansion being less than that of the mounting structure. The mounting structure includes an outer sealing portion forming a cradling member in which an annular ring member is slidably positioned. The mounting structure further includes an inner mounting portion to which a hooked end of the nozzle and shroud assembly is attached. As the inner mounting portion expands and contracts, the nozzle and shroud assembly slidably moves within the outer sealing portion.

Faulder, Leslie J. (San Diego, CA); Frey, deceased, Gary A. (late of Seattle, WA); Nielsen, Engward W. (El Cajon, CA); Ridler, Kenneth J. (San Diego, CA)

1997-01-01T23:59:59.000Z

44

LIGHTNING PROTECTION OF ROOF-MOUNTED SOLAR ...  

Science Conference Proceedings (OSTI)

Page 1. LIGHTNING PROTECTION OF ROOF-MOUNTED SOLAR CELLS ... Working paper developed for a NASA-sponsored study of solar cells ...

2013-05-17T23:59:59.000Z

45

Vlf Electromagnetic Investigations Of The Crater And Central Dome Of Mount  

Open Energy Info (EERE)

Vlf Electromagnetic Investigations Of The Crater And Central Dome Of Mount Vlf Electromagnetic Investigations Of The Crater And Central Dome Of Mount St Helens, Washington Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Vlf Electromagnetic Investigations Of The Crater And Central Dome Of Mount St Helens, Washington Details Activities (1) Areas (1) Regions (0) Abstract: A very low frequency (VLF) electromagnetic induction survey in the crater of Mount St. Helens has identified several electrically conductive structures that appear to be associated with thermal anomalies and ground water within the crater. The most interesting of these conductive structures lies beneath the central dome. It is probably a partial melt of dacite similar to that comprising the June 1981 lobe of the central dome. Author(s): James N. Towle

46

100kW Energy Transfer Multiplexer Power Converter Prototype Development Project  

DOE Green Energy (OSTI)

Project Final Report for "100kW Energy Transfer Multiplexer Power Converter Prototype Development Project" prepared under DOE grant number DE-FG36-03GO13138. This project relates to the further development and prototype construction/evaluation for the Energy Transfer Multiplexer (ETM) power converter topology concept. The ETM uses a series resonant link to transfer energy from any phase of a multiphase input to any phase of a multiphase output, converting any input voltage and frequency to any output voltage and frequency. The basic form of the ETM converter consists of an eight (8)-switch matrix (six phase power switches and two ground power switches) and a series L-C resonant circuit. Electronic control of the switches allows energy to be transferred in the proper amount from any phase to any other phase. Depending upon the final circuit application, the switches may be either SCRs or IGBTs. The inherent characteristics of the ETM converter include the following: Power processing in either direction (bidirectional); Large voltage gain without the need of low frequency magnetics; High efficiency independent of output load and frequency; Wide bandwidth with fast transient response and; Operation as a current source. The ETM is able to synthesize true sinusoidal waveforms with low harmonic distortions. For a low power PM wind generation system, the ETM has the following characteristics and advantages: It provides voltage gain without the need of low frequency magnetics (DC inductors) and; It has constant high efficiency independent of the load. The ETM converter can be implemented into a PM wind power system with smaller size, reduced weight and lower cost. As a result of our analyses, the ETM offers wind power generation technology for the reduction of the cost and size as well as the increase in performance of low power, low wind speed power generation. This project is the further theoretical/analytical exploration of the ETM converter concept in relationship to PM wind power generator applications in the 100kW and under power range. The theoretical/analytical and bench scale work focuses on simplifying the basic ETM converter topology (in terms of parts count and complexity) for the specific application of the low power PM system. The project goals and objectives were for Spellman HV will develop a 100kW prototype ETM power converter based on paralleled lower ratings converters. The proposed configuration of this prototype is a 100kW rated converter comprised of four (4) 34kW rated modules connected in parallel (the fourth converter is included to demonstrate N+1 fault tolerance). This approach is more viable as there is lower technological risk involved in developing a 34kW-rated converter than a single 100kW unit. The modular system approach should have a lower deployment and service cost over a single unit system, because of the economics of scale (smaller units at a higher volume means lower manufacturing cost) and because of improved serviceability (a non-redundant power system with one failed module will still operate at a lower power level). There is also the added benefit that greater commercial application and acceptance should be achieved by having a modular system available in which fault tolerance (N+1 or 2N) is a feature. This modular approach would allow the output power to be increased by adding more paralleled converters. Thus, the maximum output power of the overall power system is a function of the interconnection medium (the hot swap connection subsystem), rather than the ratings of a single module. The project was implemented with Spellman HV acting as the program management and production assembly and test facility; The Baker Company acting as a technical consultant and resource when required; and dtm Associates acting as the design/development resource for the hardware development of the 100kW ETM converter prototype.

S. Merrill Skeist; Richard H. (Dick) Baker; Anthony G.P. Marini; DOE Project Officer - Keith Bennett

2006-03-21T23:59:59.000Z

47

300kW Energy Storage Demonstration Project  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

kW Energy Storage Demonstration kW Energy Storage Demonstration Project Technical Overview Presented at: Annual Doe Peer Review Meeting ─ 2008 DOE Energy Storage & Power Electronics Research Programs By Ib I. Olsen September 29, 2008 116 John Street - Suite 2320 New York, New York 10038 (p) 1.212.732.5507 (f) 1.212.732.5597 www.gaiapowertech.com This project is part of the Joint Energy Storage Initiative between the New York State Energy Research and Development Authority (NYSERDA) and the Energy Storage Systems Program of the U.S. Department of Energy (DOE/ESS), and managed by Sandia National Laboratories (SNL). Sandia is a multi-program laboratory operated by Sandia Corporation, a Lockheed Martin Company, for the United States Department of Energy's National Nuclear Security Administration, under contract DE-AC04-94AL85000

48

64 kW concentrator Photovoltaics Application Test Center. Volume. Final report  

DOE Green Energy (OSTI)

Kaman Sciences Corporation has designed a 64 kW Concentrating Photovoltaic Applications Test Center (APTEC). The APTEC employs a combined concentrating photovoltaic array in a total energy system application for load sharing the electric and thermal demands of a large computer center with the interfaced electric and natural gas utility. The photovoltaic array is composed of two-axis tracking heliostats of Fresnel lens concentrating, silicon solar cell modules. The modules are cooled with a fluid which transfers heat to a ground coupled heat sink/storage unit for subsequent use in meeting the computer center's thermal load demand. The combined photovoltaic power system shares basic components - a power conditioning unit, batteries and thermal conditioning equipment - with the electric and natural gas utility service, improving the computer center's operating availability time and displacing a portion of the fossil fuel required to power the computer center with solar energy. The detailed system design is reported.

Jardine, D.M.; Jones, D.W.

1980-06-01T23:59:59.000Z

49

Mount St. Mary's Abbey | Open Energy Information  

Open Energy Info (EERE)

St. Mary's Abbey St. Mary's Abbey Jump to: navigation, search Name Mount St. Mary's Abbey Facility Mount St. Mary's Abbey Sector Wind energy Facility Type Small Scale Wind Facility Status In Service Owner Mount St. Mary's Abbey Developer Sustainable Energy Developments Energy Purchaser Mount St. Mary's Abbey Location Wrentham MA Coordinates 42.033096°, -71.393711° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":42.033096,"lon":-71.393711,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

50

The Mount Washington Observatory—50 Years Old  

Science Conference Proceedings (OSTI)

The Mount Washington Observatory celebrates its 50th Anniversary this year. The history of the establishment and of the early days of the Observatory is summarized, and its research programs, instrumentation, and facilities from the early days to ...

Alan A. Smith

1982-09-01T23:59:59.000Z

51

Motorized control for mirror mount apparatus  

DOE Patents (OSTI)

A motorized control and automatic braking system for adjusting mirror mount apparatus is disclosed. The motor control includes a planetary gear arrangement to provide improved pitch adjustment capability while permitting a small packaged design. The motor control for mirror mount adjustment is suitable for laser beam propagation applications. The brake is a system of constant contact, floating detents which engage the planetary gear at selected between-teeth increments to stop rotation instantaneously when the drive motor stops.

Cutburth, Ronald W. (Tracy, CA)

1989-01-01T23:59:59.000Z

52

Wind Turbine Safety and Function Test Report for the Gaia-Wind 11-kW Wind Turbine  

DOE Green Energy (OSTI)

This test was conducted as part of the U.S. Department of Energy's (DOE) Independent Testing project. This project was established to help reduce the barriers to wind energy expansion by providing independent testing results for small wind turbines (SWT). In total, four turbines were tested at the National Wind Technology Center (NWTC) as a part of this project. Safety and function testing is one of up to five tests performed on the turbines, including power performance, duration, noise, and power-quality tests. The results of the testing provide the manufacturers with reports that can be used for small wind turbine certification. The test equipment includes a Gaia-Wind 11-kW wind turbine mounted on an 18-m monopole tower. Gaia-Wind Ltd. manufactured the turbine in Denmark. The system was installed by the NWTC site operations group with guidance and assistance from Gaia-Wind.

Huskey, A.; Bowen, A.; Jager, D.

2010-01-01T23:59:59.000Z

53

10 kW SOFC POWER SYSTEM COMMERCIALIZATION  

SciTech Connect

The program is organized into three developmental periods. In Phase 1 the team will develop and demonstrate a proof-of-concept prototype design and develop a manufacturing plan to substantiate potential producibility at a target cost level of $800/kW factory manufacturing cost. Phase 2 will further develop the design and reduce the manufacturing cost to a level of $600 kW. Depending on an assessment of the maturity of the technology at the end of Phase 1, Phase 2 may be structured and supplemented to provide a limited production capability. Finally, in Phase 3, a full Value Package Introduction (VPI) Program will be integrated into the SECA program to develop a mass-producible design at a factory cost of $400/kW with full cross-functional support for unrestricted commercial sales. The path to market for new technology products in the Cummins system involves two processes. The first is called Product Preceding Technology, or PPT. The PPT process provides a methodology for exploring potentially attractive technologies and developing them to the point that they can be reliably scheduled into a new product development program with a manageable risk to the product introduction schedule or product quality. Once a technology has passed the PPT gate, it is available to be incorporated into a Value Package Introduction (VPI) Program. VPI is the process that coordinates the cross-functional development of a fully supported product. The VPI Program is designed to synchronize efforts in engineering, supply, manufacturing, marketing, finance, and product support areas in such a way that the product, when introduced to the market, represents the maximum value to the customer.

Dan Norrick; Brad Palmer; Charles Vesely; Eric Barringer; Cris DeBellis; Rich Goettler; Kurt Kneidel; Milind Kantak; Steve Kung; Tom Morris; Greg Rush

2004-02-01T23:59:59.000Z

54

10 kW SOFC POWER SYSTEM COMMERCIALIZATION  

SciTech Connect

The program is organized into three developmental periods. In Phase 1 the team will develop and demonstrate a proof-of-concept prototype design and develop a manufacturing plan to substantiate potential producibility at a target cost level of $800/kW factory manufacturing cost. Phase 2 will further develop the design and reduce the manufacturing cost to a level of $600 kW. Depending on an assessment of the maturity of the technology at the end of Phase 1, Phase 2 may be structured and supplemented to provide a limited production capability. Finally, in Phase 3, a full Value Package Introduction (VPI) Program will be integrated into the SECA program to develop a mass-producible design at a factory cost of $400/kW with full cross-functional support for unrestricted commercial sales. The path to market for new technology products in the Cummins system involves two processes. The first is called Product Preceding Technology, or PPT. The PPT process provides a methodology for exploring potentially attractive technologies and developing them to the point that they can be reliably scheduled into a new product development program with a manageable risk to the product introduction schedule or product quality. Once a technology has passed the PPT gate, it is available to be incorporated into a Value Package Introduction (VPI) Program. VPI is the process that coordinates the cross-functional development of a fully supported product. The VPI Program is designed to synchronize efforts in engineering, supply, manufacturing, marketing, finance, and product support areas in such a way that the product, when introduced to the market, represents the maximum value to the customer.

Dan Norrick; Brad Palmer; Todd Romine; Charles Vesely; Eric Barringer; Cris DeBellis; Rich Goettler; Kurt Kneidel; Milind Kantak; Steve Kung; Greg Rush

2003-08-01T23:59:59.000Z

55

Grounding and Lightning Protection of Capacitor Controllers  

Science Conference Proceedings (OSTI)

This is the third report in EPRI's capacitor reliability study. It deals with capacitor controller grounding and lightning protection. Prior reports dealt with nuisance fuse operations, operating and construction practices, and use of distribution line capacitors for transmission voltage support. Simulations were performed to investigate various controller mounting locations and grounding configurations and their impact on the magnitude of surges reaching the controller. Once these aspects of capacitor c...

2005-03-08T23:59:59.000Z

56

Grounding intentionality  

E-Print Network (OSTI)

In this thesis, I argue that current attempts to ground intentionality face one of two challenges. Either the grounding feature of intentionality will be itself intentional or the grounding feature is disparate in nature from the representational capacity of an intentional mental state and therefore no connection between the two can be taken to exist. I examine two current accounts of intentionality and the features they utilize to ground it. I maintain that both views fall prey to one or both of the objections I raise. I conclude that any account of intentionality will need to meet both of these challenges in order to be counted successful.

Huizenga Steven R

2004-01-01T23:59:59.000Z

57

205 kW Photovoltaic (PV) System Installed on the U.S. Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

205 kW Photovoltaic (PV) System Installed on the U.S. Department of Energy's Forrestal Building 205 kW Photovoltaic (PV) System Installed on the U.S. Department of Energy's...

58

Mount Wachusetts Wind Farm | Open Energy Information  

Open Energy Info (EERE)

Mount Wachusetts Wind Farm Mount Wachusetts Wind Farm Facility Mount Wachusetts Wind Farm Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner Princeton Municipal Light Developer CEI - Iberdrola Energy Purchaser Princeton Municipal Light Location Near Princeton MA Coordinates 42.588458°, -71.98387° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":42.588458,"lon":-71.98387,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

59

Sensor mount assemblies and sensor assemblies  

DOE Patents (OSTI)

Sensor mount assemblies and sensor assemblies are provided. In an embodiment, by way of example only, a sensor mount assembly includes a busbar, a main body, a backing surface, and a first finger. The busbar has a first end and a second end. The main body is overmolded onto the busbar. The backing surface extends radially outwardly relative to the main body. The first finger extends axially from the backing surface, and the first finger has a first end, a second end, and a tooth. The first end of the first finger is disposed on the backing surface, and the tooth is formed on the second end of the first finger.

Miller, David H. (Redondo Beach, CA)

2012-04-10T23:59:59.000Z

60

500-kW DCHX pilot-plant evaluation testing  

DOE Green Energy (OSTI)

Field tests with the 500 kW Direct Contact Pilot Plant were conducted utilizing brine from well Mesa 6-2. The tests were intended to develop comprehensive performance data, design criteria, and economic factors for the direct contact power plant. The tests were conducted in two phases. The first test phase was to determine specific component performance of the DCHX, turbine, condensers and pumps, and to evaluate chemical mass balances of non-condensible gases in the IC/sub 4/ loop and IC/sub 4/ in the brine stream. The second test phase was to provide a longer term run at nearly fixed operating conditions in order to evaluate plant performance and identify operating cost data for the pilot plant. During these tests the total accumulated run time on major system components exceeded 1180 hours with 777 hours on the turbine prime mover. Direct contact heat exchanger performance exceeded the design prediction.

Hlinak, A.; Lee, T.; Loback, J.; Nichols, K.; Olander, R.; Oshmyansky, S.; Roberts, G.; Werner, D.

1981-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "kw ground mounted" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Ground Water  

NLE Websites -- All DOE Office Websites (Extended Search)

Water Nature Bulletin No. 408-A February 27, 1971 Forest Preserve District of Cook County George W. Dunne, President Roland F. Eisenbeis, Supt. of Conservation GROUND WATER We take...

62

Ground Loops for Heat Pumps and Refrigeration  

E-Print Network (OSTI)

Ground loops are used for water source heat pumps. Refrigeration can be put on a ground loop. Water-cooled condensing units are more efficient than air-cooled, and they can be put indoors. Indoor location makes piping for desuperheater hot water easy. Since refrigeration equipment runs more than heat pumps, energy savings can be large for ground-coupled refrigeration. The paper presents a design procedure for ground loops for heat pumps, hot water, ice machines, and water-cooled refrigeration. It gives an overview of the commercial ground-coupled systems in Louisiana that have both refrigeration and heat pumps. Systems vary from small offices to a three-story office building with 187 tons. A chain of hamburger outlets uses total ground-coupling in all of its stores. A grocery store has ground-coupling for heat pumps and refrigeration. Desuperheaters provide 80 percent of the hot water for a coin laundry in the same building. A comparison of energy costs in a bank with a ground-coupled heat pump system to a similar bank with air-conditioning and gas for heat revealed a 31 percent reduction in utility costs for the ground-coupled building. Two buildings of the Mississippi Power and Light Co. have ground-coupled heat pumps in one, and high efficiency air source heat pumps in the other. Energy savings in nine months was 60,000 kWh (25 percent), and electric peak demand was reduced 42 kW (35 percent).

Braud, H. J.

1986-01-01T23:59:59.000Z

63

10 kW SOFC Power System Commercialization  

DOE Green Energy (OSTI)

Cummins Power Generation (CPG) as the prime contractor and SOFCo-EFS Holdings LLC (SOFCo), as their subcontractor, teamed under the Solid-state Energy Conversion Alliance (SECA) program to develop 3-10kW solid oxide fuel cell systems for use in recreational vehicles, commercial work trucks and stand-by telecommunications applications. The program goal is demonstration of power systems that meet commercial performance requirements and can be produced in volume at a cost of $400/kW. This report summarizes the team's activities during the seventh six-month period (July-December 2005) of the four-year Phase I effort. While there has been significant progress in the development of the SOFC subsystems that can support meeting the program Phase 1 goals, the SOFCo ceramic stack technology has progressed significantly slower than plan and CPG consider it unlikely that the systemic problems encountered will be overcome in the near term. SOFCo has struggled with a series of problems associated with inconsistent manufacturing, inadequate cell performance, and the achievement of consistent, durable, low resistance inter-cell connections with reduced or no precious materials. A myriad of factors have contributed to these problems, but the fact remains that progress has not kept pace with the SECA program. A contributing factor in SOFCo's technical difficulties is attributed to their significantly below plan industry cost share spending over the last four years. This has resulted in a much smaller SOFC stack development program, has contributed to SOFCo not being able to aggressively resolve core issues, and clouds their ability to continue into a commercialization phase. In view of this situation, CPG has conducted an independent assessment of the state-of-the-art in planar SOFC's stacks and have concluded that alternative technology exists offering the specific performance, durability, and low cost needed to meet the SECA objectives. We have further concluded that there is insufficient evidence to reliably predict that SOFCo will be able to achieve the SECA performance and cost goals on a schedule consistent with SECA or CPG commercialization goals. CPG believes SOFCo have made a good faith effort consistent with the available resources, but have repeatedly fallen short of achieving the programs scheduled targets. CPG has therefore initiated a process of application for extension of Phase 1 of our SECA program with the intent of transitioning to an alternative stack supplier with more mature SOFC technology, and demonstrating a system meeting the SECA Phase 1 goals by the end of calendar 2006. We have identified an alternative supplier and will be reporting the progress on transition and program planning in monthly technical reports, reviews, and in the next semiannual report.

Dan Norrick; Brad Palmer; Charles Vesely; Eric Barringer; John Budge; Cris DeBellis; Rich Goettler; Milind Kantak; Steve Kung; Zhien Liu; Tom Morris; Keith Rackers; Gary Roman; Greg Rush; Liang Xue

2006-02-01T23:59:59.000Z

64

NETL F 451.1-1/1 Categorical Exclusion (CX) Designation Form  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Energy Program Revised narrative and budget. Projects allowable include wind < 20kW, rooftop solar, ground mounted solar <20kW, closed loop ground source heat pumps, solar...

65

Fixture for mounting small parts for processing  

DOE Patents (OSTI)

This invention is comprised of a fixture for mounting small parts, such as fusion target spheres or microelectronic components. A glass stalk is drawn and truncated near its tip. The truncated end of the glass stalk is dipped into silicone rubber forming an extending streamer. After the rubber cures for approximately 24 hours, a small part is touched to the streamer, and will be held securely throughout processing. 5 figs.

Foreman, L.R.; Gomez, V.M.; Thomas, M.H.

1988-09-29T23:59:59.000Z

66

Mounting assembly for heater thermostat control  

Science Conference Proceedings (OSTI)

This patent describes an assembly for mounting a thermostat control on the outer wall of a heater tank including an external spud in which a heating element is mounted. The mounting assembly comprises: a first bracket made from a spring material and including a body having an opening adapted to lockingly fit over the tank spud. The first bracket further includes a pair of laterally-spaced legs extending from the body and having a bent upper end portion adapted to apply spring pressure toward the tank outer wall when the first bracket is locked on the tank spud. Each of the legs includes in the upper end portion an elongated slot having an upper end; a second bracket carrying the thermostat control and having a pair of laterally -spaced, upstanding ears adapted to fit beneath the upper end portions of the legs. Each of the ears includes a nib received in a slot for interlocking the first and the second brackets and having an upper edge adapted to engage the upper end of the slot and cooperate therewith to urge the thermostat control into firmer contact with the tank outer wall in response to upward vertical movement of the second bracket relative to the first bracket; and the assembly further characterized by a retaining lip on the first bracket, the lip located between the legs and positioned to bear against the end wall of the thermostat control when the parts are in assembled position and an outward horizontal load is applied.

Murphy, M.A.

1987-04-14T23:59:59.000Z

67

Molten carbonate fuel cell technology improvement. [25 kW  

DOE Green Energy (OSTI)

This report summarizes the work performed under Department of Energy Contract AC21-87MC23270 during the period March 1, through May 30, 1990. The overall objective of this program is to define a competitive CG/MCFC power plant and the associated technology development requirements and to develop an improved cell configuration for molten carbonate fuel cells which has improved performance, has reduced cell creep and electrolyte management consistent with 40,000 hour projected life, reduces existing cell cost, and is adaptable to a range of power plant applications. The 8-ft{sup 2} 20-cell, 25-kW stack assembly and installation in the test facility were completed. Testing of the stack was started and 896 hours of test time were reached. Manifold seal development focused on a seal to reduce electrolyte transport and test rigs were initiated for shunt current and seal leakage evaluation. Development on sheet metal parts was initiated with focus on improved aluminization for separator plate corrosion protection and nickel clad stainless steel for the anode current collector. Development of porous parts was initiated with focus on an alternative binder for the electrodes. Design of a laboratory scale continuous debinding oven was completed. Development of an improved material blend for the matrix was also initiated. 19 figs., 2 tabs.

Not Available

1990-09-01T23:59:59.000Z

68

Characterization of Settler Tank and KW Container Sludge Simulants  

SciTech Connect

The Sludge Treatment Project (STP), managed by CH2M Hill Plateau Remediation Company (CHPRC) has specified base formulations for non-radioactive sludge simulants for use in the development and testing of equipment for sludge sampling, retrieval, transport, and processing. In general, the simulant formulations are based on the average or design-basis physical and chemical properties obtained by characterizing sludge samples. The simulants include surrogates for uranium metal, uranium oxides (agglomerates and fine particulate), and the predominant chemical phases (iron and aluminum hydroxides, sand). Specific surrogate components were selected to match the nominal particle-size distribution and particle-density data obtained from sludge sample analysis. Under contract to CHPRC, Pacific Northwest National Laboratory (PNNL) has performed physical and rheological characterization of simulants, and the results are reported here. Two base simulant types (dry) were prepared by STP staff at the Maintenance and Storage Facility and received by PNNL on February 12, 2009: Settler Tank Simulant and KW Container Sludge Simulant. The objectives of this simulant characterization effort were to provide baseline characterization data on simulants being used by STP for process development and equipment testing and provide a high-level comparison of the simulant characteristics to the targets used to formulate the simulants.

Burns, Carolyn A.; Luna, Maria; Schmidt, Andrew J.

2009-05-12T23:59:59.000Z

69

Comparison of Distributed Generation Technology Options, 250-400 kW  

Science Conference Proceedings (OSTI)

The Los Angeles County Sanitation Districts own and operate biogas-fueled generating plants at a number of sites. Included in their portfolio are a 250 kW carbonate fuel cell, a 250 kW microturbine, a 400 kW internal combustion engine, and a cluster of ten (10) 30-kW microturbines. This afforded a unique opportunity to compare the power generation technologies. All of these systems use bio-gas that would otherwise be flared and generate power in parallel with the local utility to offset site electrical p...

2006-03-09T23:59:59.000Z

70

225-kW Dynamometer for Testing Small Wind Turbine Components  

DOE Green Energy (OSTI)

Poster for WindPower 2006 held June 4-7, 2006, in Pittsburgh, PA, describing the 225-kW dynamometer for testing small wind turbine components.

Green, J.

2006-06-01T23:59:59.000Z

71

Test #6.5, natural gas, HRR=400 kW  

Science Conference Proceedings (OSTI)

*. Bookmark and Share. Reduced Scale Enclosure Fire Images (NIST TN1483). Test #6.5, natural gas, HRR=400 kW.

2012-03-20T23:59:59.000Z

72

Mechanical filtering characteristics of passive periodic engine mount  

Science Conference Proceedings (OSTI)

The transmission of automotive engine vibrations to the chassis is isolated using a new class of mounts which rely in their operation on optimally designed and periodically distributed viscoelastic inserts. The proposed mount acts as a mechanical filter ... Keywords: Experimental validation, Finite element analysis, Periodic engine mount, Transfer matrix approach

Woojin Jung; Zheng Gu; A. Baz

2010-09-01T23:59:59.000Z

73

Mount Zirkel Wilderness and vicinity, Colorado  

SciTech Connect

Several areas of metallic and nonmetallic mineralization have been identified from surface occurrences within the Mount Zirkel Wilderness and vicinity, Colorado. Three areas of probable copper-lead-zinc-silver-gold resource potential, two areas of probable chrome-platinum resource potential, four areas of probable uranium-thorium resource potential, two areas of probable molybdenum resource potential, and one area of probable fluorspar potential were identified by studies in 1965-1973 by the USGS and USBM. No potential for fossil fuel or geothermal resources was identified.

Snyder, G.L.; Patten, L.L.

1984-01-01T23:59:59.000Z

74

ACHIEVING 800 KW CW BEAM POWER AND CONTINUING ENERGY IMPROVEMENTS IN CEBAF*  

E-Print Network (OSTI)

ACHIEVING 800 KW CW BEAM POWER AND CONTINUING ENERGY IMPROVEMENTS IN CEBAF* C. E. Reece Thomas, CEBAF at Jefferson Lab has demonstrated its full capacity of sustained 800 kW beam power. All systems the energy reach of CEBAF, we began a program of processing all installed cryomodules. This processing has

75

Generator set, 100kW frequency converter. Final technical report  

SciTech Connect

The Contractor shall furnish all engineering labor, tools, services, supplies, materials, equipment, and facilities necessary to perform an investigation and study of means to extend the capability of the contractor's existing Power Center Inverter System to the 100 kW level. This 100 kW Inverter System shall meet the basic performance parameters of the frequency converter.

Corry, T.

1975-07-01T23:59:59.000Z

76

Rigid laser mirror mount and protection assembly  

SciTech Connect

A mounting assembly for supporting a Brewster window and mirror to intercept a laser beam at the end of a gas laser envelope includes an elongated tubular member having one end opening into the gas laser envelope and an opposite end closed by the Brewster window. A rigid housing supporting the mirror is joined to the tubular member close to the end having the Brewster window by a flexible sealed joint that permits limited movement of the housing relative to the tubular member generally along the length of the tubular member while inhibiting flow of contaminants from the exterior into the passage formed by the rigid housing between the Brewster window and mirror. A seal is placed between the rigid housing and mirror to inhibit flow of such contaminants into the passage from the mirror location. A mounting structure joins the rigid housing to the gas laser envelope to secure them together and includes an adjustment mechanism that permits the housing to be moved relative to the envelope for adjusting the angular orientation of the supported mirror relative to the intercepted laser beam.

Mohler, G.E.

1984-03-27T23:59:59.000Z

77

Photo of the Week: Argonne's 10 kW Wind Turbine | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Photo of the Week: Argonne's 10 kW Wind Turbine Photo of the Week: Argonne's 10 kW Wind Turbine Photo of the Week: Argonne's 10 kW Wind Turbine November 9, 2012 - 11:57am Addthis At Argonne National Laboratory, the power generated by this 10 kW wind turbine helps scientists and engineers study the interaction of wind energy, electric vehicle charging and grid technology. The turbine is also estimated to offset more than 10 metric tons of greenhouse gas emissions annually. Learn more about renewable energy research at Argonne. | Photo courtesy of Argonne National Laboratory. At Argonne National Laboratory, the power generated by this 10 kW wind turbine helps scientists and engineers study the interaction of wind

78

Site Visit Report, Hanford Sludge Treatment Project 105-KW - August 2011 |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Sludge Treatment Project 105-KW - August Sludge Treatment Project 105-KW - August 2011 Site Visit Report, Hanford Sludge Treatment Project 105-KW - August 2011 August 2011 Hanford Sludge Treatment Project 105-KW Final Safety Analysis Report Review This report documents the results of a review conducted by the Office of Health, Safety and Security (HSS) of selected aspects of the 105-KW Basin Final Safety Analysis Report (HNF-SD-WM-SAR-062, Revision 14C) for the Sludge Treatment Project at the Hanford Site. HSS's review of the K-West Basin FSAR found it to be generally adequate with respect to the scope of this review. However, some aspects of the FSAR accident analyses of two events may warrant further review: MCO transport cask drop into the K-Basin, and the fire accident event involving the cask

79

Wind Turbine Generator System Duration Test Report for the Gaia-Wind 11 kW Wind Turbine  

DOE Green Energy (OSTI)

This test was conducted as part of the U.S. Department of Energy's (DOE) Independent Testing project. This project was established to help reduce the barriers of wind energy expansion by providing independent testing results for small turbines. In total, five turbines are being tested at the National Renewable Energy Laboratory's (NRELs) National Wind Technology Center (NWTC) as a part of this project. Duration testing is one of up to five tests that may be performed on the turbines, including power performance, safety and function, noise, and power quality tests. The results of the testing will provide the manufacturers with reports that may be used for small wind turbine certification. The test equipment includes a Gaia-Wind 11 kW wind turbine mounted on an 18 m monopole tower. Gaia-Wind Ltd. manufactured the turbine in Denmark, although the company is based in Scotland. The system was installed by the NWTC Site Operations group with guidance and assistance from Gaia-Wind.

Huskey, A.; Bowen, A.; Jager, D.

2010-09-01T23:59:59.000Z

80

Mount Spurr Geothermal Project | Open Energy Information  

Open Energy Info (EERE)

Spurr Geothermal Project Spurr Geothermal Project Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Development Project: Mount Spurr Geothermal Project Project Location Information Coordinates 61.299722222222°, -152.25138888889° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":61.299722222222,"lon":-152.25138888889,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

Note: This page contains sample records for the topic "kw ground mounted" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Rack assembly for mounting solar modules  

SciTech Connect

A rack assembly is provided for mounting solar modules over an underlying body. The rack assembly may include a plurality of rail structures that are arrangeable over the underlying body to form an overall perimeter for the rack assembly. One or more retention structures may be provided with the plurality of rail structures, where each retention structure is configured to support one or more solar modules at a given height above the underlying body. At least some of the plurality of rail structures are adapted to enable individual rail structures to be sealed over the underlying body so as to constrain air flow underneath the solar modules. Additionally, at least one of (i) one or more of the rail structures, or (ii) the one or more retention structures are adjustable so as to adapt the rack assembly to accommodate solar modules of varying forms or dimensions.

Plaisted, Joshua Reed; West, Brian

2012-09-04T23:59:59.000Z

82

Rack assembly for mounting solar modules  

SciTech Connect

A rack assembly is provided for mounting solar modules over an underlying body. The rack assembly may include a plurality of rail structures that are arrangeable over the underlying body to form an overall perimeter for the rack assembly. One or more retention structures may be provided with the plurality of rail structures, where each retention structure is configured to support one or more solar modules at a given height above the underlying body. At least some of the plurality of rail structures are adapted to enable individual rail structures o be sealed over the underlying body so as to constrain air flow underneath the solar modules. Additionally, at least one of (i) one or more of the rail structures, or (ii) the one or more retention structures are adjustable so as to adapt the rack assembly to accommodate solar modules of varying forms or dimensions.

Plaisted, Joshua Reed (Oakland, CA); West, Brian (San Francisco, CA)

2010-12-28T23:59:59.000Z

83

Reusable vibration resistant integrated circuit mounting socket  

DOE Patents (OSTI)

This invention discloses a novel form of socket for integrated circuits to be mounted on printed circuit boards. The socket uses a novel contact which is fabricated out of a bimetallic strip with a shape which makes the end of the strip move laterally as temperature changes. The end of the strip forms a barb which digs into an integrated circuit lead at normal temperatures and holds it firmly in the contact, preventing loosening and open circuits from vibration. By cooling the contact containing the bimetallic strip the barb end can be made to release so that the integrated circuit lead can be removed from the socket without damage either to the lead or to the socket components.

Evans, Craig N. (Irwin, PA)

1995-01-01T23:59:59.000Z

84

Article mounting and position adjustment stage  

DOE Patents (OSTI)

An improved adjustment and mounting stage of the type used for the detection of laser beams is disclosed. A ring sensor holder has locating pins on a first side thereof which are positioned within a linear keyway in a surrounding housing for permitting reciprocal movement of the ring along the keyway. A rotatable ring gear is positioned within the housing on the other side of the ring from the linear keyway and includes an oval keyway which drives the ring along the linear keyway upon rotation of the gear. Motor-driven single-stage and dual (x, y) stage adjustment systems are disclosed which are of compact construction and include a large laser transmission hole. 6 figs.

Cutburth, R.W.; Silva, L.L.

1988-05-10T23:59:59.000Z

85

Platforms: Where the sensors are mounted.  

E-Print Network (OSTI)

and a phase value: · radiometry value is a measure of ground reflectivity. · phase value is a feature, the small particles of "stuff" in the air that includes cloud droplets. Five minutes of LITE observations reveals truth. The curtain is lifted and the truth revealed. The paint on the outside of the can has been

Gilbes, Fernando

86

Geochemistry of a volcanic hydrothermal system at Mount Spurr, Alaska.  

E-Print Network (OSTI)

??Mount Spurr is an ice and snow-covered andesitic volcano located at the northern extent of the Aleutian arc in south central Alaska. Previous workers have… (more)

Garchar, Laura

2012-01-01T23:59:59.000Z

87

Minor Element Distributions in Mount Isa Copper Smelter  

Science Conference Proceedings (OSTI)

On-Site Speaker (Planned), Pengfu Tan. Abstract Scope, Xstrata Copper Smelter at Mount Isa in Australia has operated one copper Isasmelt furnace, two Rotary ...

88

Temporal Geochemical Variations In Volatile Emissions From Mount...  

Open Energy Info (EERE)

Temporal Geochemical Variations In Volatile Emissions From Mount St Helens, Usa, 1980-1994 Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Temporal...

89

Mount Vernon, Ohio: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

Knox County, Ohio. It falls under Ohio's 18th congressional district.12 Registered Energy Companies in Mount Vernon, Ohio Blight-to-Bright Replex Plastics References US...

90

225-kW Dynamometer for Testing Small Wind Turbine Components: Preprint  

DOE Green Energy (OSTI)

This paper describes NREL's new 225-kW dynamometer facility that is suitable for testing a variety of components and subsystems for small wind turbines and discusses opportunities for industry partnerships with NREL for use of the facility.

Green, J.

2006-06-01T23:59:59.000Z

91

Ingersoll Rand VSD Oil Injected Screw Air Compressor (37-75kW ...  

U.S. Energy Information Administration (EIA)

Ingersoll Rand VSD Oil Injected Screw Air Compressor (37-75kW / 50-100HP VSD),Kunshan CompAirs Machinery Plant Co.,Ltd is the leading air compressor ...

92

Beyond kWh and kW demand: Understanding the new real-time electric...  

NLE Websites -- All DOE Office Websites (Extended Search)

Beyond kWh and kW demand: Understanding the new real-time electric power measurement system in LBNL Building 90 Speaker(s): Alex McEachern Date: January 14, 2010 - 12:00pm...

93

The Mount Wilson Ca II K index  

E-Print Network (OSTI)

It is well established that both total and spectral solar irradiance are modulated by variable magnetic activity on the solar surface. However, there is still disagreement about the contribution of individual solar features for changes in the solar output, in particular over decadal time scales. Ionized Ca II K line spectroheliograms are one of the major resources for these long-term trend studies, mainly because such measurements have been available now for more than 100 years. In this paper we introduce a new Ca II K plage and active network index time series derived from the digitization of almost 40,000 photographic solar images that were obtained at the 60-foot solar tower, between 1915 and 1985, as a part of the monitoring program of the Mount Wilson Observatory. We describe here the procedure we applied to calibrate the images and the properties of our new defined index, which is strongly correlated to the average fractional area of the visible solar disk occupied by plages and active network. We show ...

Bertello, Luca; Boyden, John E; 10.1007/s11207-010-9570-z

2010-01-01T23:59:59.000Z

94

Simulation of Dynamic Characteristic for Passive Hydraulic Mount  

Science Conference Proceedings (OSTI)

Dynamic modeling of Passive Hydraulic Engine Mounts (PHEM) is developed with inertia track, decoupler and throttle. Mathematically, the state equations governing vibration isolation behaviors of the PHEMs are presented and solved by means of the lumped ... Keywords: passive hydraulic mount, simulation, test

Zhang Yunxia; Fang Zuhua

2009-08-01T23:59:59.000Z

95

Environmental impacts of large-scale grid-connected ground-mounted PV installations  

E-Print Network (OSTI)

,6]. They highlighted the photovoltaic potential for a low carbon energy supply and the environmental benefits of PV comparison of energy supply options. 21st European Photovoltaic Solar Energy Conference. 2006. [8] IEA European Photovoltaic Energy Conference. 2008. [12] D. Beloin-Saint-Pierre, I. Blanc, J. Payet, P. Jacquin

96

Pattern Of Shallow Ground Water Flow At Mount Princeton Hot Springs...  

Open Energy Info (EERE)

is complicated by quaternary deposits (including glacial and fluvial deposits), we use DC electrical resistivity tomography and self-potential mapping to identify preferential...

97

NETL F 451.1-1/1 Categorical Exclusion (CX) Designation Form  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

R. Benitez State of Georgia State Energy Program - Clean Energy Property Rebate Program Installation of PV on buildings, parking facilities or ground mount < 60kW; wind < 20kW,...

98

NETL F 451.1-1/1 Categorical Exclusion (CX) Designation Form  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

04302012 State of Georgia State Energy Program - Clean Energy Property Rebate Program Installation of PV on buildings, parking facilities or ground mount < 60kW; wind < 20kW,...

99

u.s. DEPARTJvIENT OF ENERGY EERE PROJECT MANAGEMENT CENTER NEPA...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

of DOE SEP funding to the Unified State Laboratories for a ground mounted 36 kW solar (PV) photovoltaic system. The proposed project will be comprised of four 9 kW arrays...

100

Model As-of Right Zoning Ordinance or Bylaw: Allowing Use of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

250 kilowatts (kW) or more). The model "as-of-right" siting must allow for ground-mounted solar photovoltaic installations 250 kW (DC) or more. An essential part of "as-of-right"...

Note: This page contains sample records for the topic "kw ground mounted" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Methods and apparatus for radially compliant component mounting  

DOE Patents (OSTI)

Methods and apparatus for a mounting assembly for a liner of a gas turbine engine combustor are provided. The combustor includes a combustor liner and a radially outer annular flow sleeve. The mounting assembly includes an inner ring surrounding a radially outer surface of the liner and including a plurality of axially extending fingers. The mounting assembly also includes a radially outer ring coupled to the inner ring through a plurality of spacers that extend radially from a radially outer surface of the inner ring to the outer ring.

Bulman, David Edward (Cincinnati, OH); Darkins, Jr., Toby George (Loveland, OH); Stumpf, James Anthony (Columbus, IN); Schroder, Mark S. (Greenville, SC); Lipinski, John Joseph (Simpsonville, SC)

2012-03-27T23:59:59.000Z

102

Qualified Energy Property Tax Exemption for Projects over 250 kW (Payment  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Qualified Energy Property Tax Exemption for Projects over 250 kW Qualified Energy Property Tax Exemption for Projects over 250 kW (Payment in Lieu) Qualified Energy Property Tax Exemption for Projects over 250 kW (Payment in Lieu) < Back Eligibility Commercial Utility Savings Category Bioenergy Commercial Heating & Cooling Manufacturing Buying & Making Electricity Alternative Fuel Vehicles Hydrogen & Fuel Cells Water Solar Wind Program Info Start Date 01/01/2010 State Ohio Program Type Property Tax Incentive Rebate Amount 100% property tax exemption; payment in lieu of tax required Provider Ohio Development Services Agency Ohio's Renewable and Advanced Energy Project Property Tax Exemption, enacted with the passage of Ohio S.B. 232 in the summer of 2010, exempts qualified energy projects in Ohio from public utility tangible personal

103

STATEMENT OF CONSIDERATIONS REQUEST BY KENETECH WINDPOWER, INC. (KW) FOR AN  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

KENETECH WINDPOWER, INC. (KW) FOR AN KENETECH WINDPOWER, INC. (KW) FOR AN ADVANCE WAIVER OF DOMESTIC AND FOREIGN PATENT RIGHTS UNDER NREL SUBCONTRACT NO: AAA-5-13320-02 UNDER DOE CONTRACT NO: DE-AC36-83CH10093 W(A)-95-003; CH-0849 Kenetech Windpower, Inc. (KW) has requested a waiver of domestic and foreign patent rights for all subject inventions arisg from the above referenced subcontract entitled "Advanced Wind Turbine Program Next Generation Turbine Development Project." The objective of the work to be performed under this subcontract is to design and develop an advanced next generation wind turbine capable of producing electricity for $0.04/kWh or less at 5.8 m/s(13mph) sites in the 1998-2000 time period. The work is to proceed in two stages. In the first stage, which is the subject of this waiver, the work comprises a concept study to develop

104

Qualified Energy Property Tax Exemption for Projects 250 kW or Less |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Qualified Energy Property Tax Exemption for Projects 250 kW or Less Qualified Energy Property Tax Exemption for Projects 250 kW or Less Qualified Energy Property Tax Exemption for Projects 250 kW or Less < Back Eligibility Commercial Utility Savings Category Bioenergy Alternative Fuel Vehicles Hydrogen & Fuel Cells Buying & Making Electricity Solar Home Weatherization Water Wind Program Info Start Date 01/01/2010 State Ohio Program Type Property Tax Incentive Rebate Amount 100% exemption Provider Ohio Development Services Agency Ohio's Renewable and Advanced Energy Project Property Tax Exemption, enacted with the passage of Ohio S.B. 232 in the summer of 2010, exempts qualified energy projects in Ohio from public utility tangible personal property taxes and real property taxes*. Before passage of S.B. 232, a renewable energy facility in Ohio that sold electricity to a third-party

105

Trade Study on Aggregation of Multiple 10-KW Solid Ozide Fuel Cell Power Modules  

DOE Green Energy (OSTI)

According to the Solid State Energy Conversion Alliance (SECA) program guidelines, solid oxide fuel cells (SOFC) will be produced in the form of 3-10 kW modules for residential use. In addition to residential use, these modules can also be used in apartment buildings, hospitals, etc., where a higher power rating would be required. For example, a hospital might require a 250 kW power generating capacity. To provide this power using the SECA SOFC modules, 25 of the 10 kW modules would be required. These modules can be aggregated in different architectures to yield the necessary power. This report will show different approaches for aggregating numerous SOFC modules and will evaluate and compare each one with respect to cost, control complexity, ease of modularity, and fault tolerance.

Ozpineci, B.

2004-12-03T23:59:59.000Z

106

NedPower Mount Storm LLC | Open Energy Information  

Open Energy Info (EERE)

NedPower Mount Storm LLC NedPower Mount Storm LLC Jump to: navigation, search Name NedPower Mount Storm LLC Place Chantilly, Virginia Zip 20151 Sector Wind energy Product Owner of the Mount Storm wind project in Grant County, West Virginia. Coordinates 38.883607°, -77.439755° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":38.883607,"lon":-77.439755,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

107

Temporal Geochemical Variations In Volatile Emissions From Mount St Helens,  

Open Energy Info (EERE)

Temporal Geochemical Variations In Volatile Emissions From Mount St Helens, Temporal Geochemical Variations In Volatile Emissions From Mount St Helens, Usa, 1980-1994 Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Temporal Geochemical Variations In Volatile Emissions From Mount St Helens, Usa, 1980-1994 Details Activities (2) Areas (1) Regions (0) Abstract: Fumarole discharges (95-560°C) collected from the dacite dome inside Mount St. Helens crater show temporal changes in their isotopic and chemical compositions. A ΔD vs. Δ18O plot shows that condensed waters from the gases are mixtures of meteoric and magmatic components, but that the apparent magmatic end-member in 1994 was depleted by about 7‰ in ΔD relative to the apparent end-member in 1980. Based on ΔD modeling, approximately 63% of shallow, post-1980 magma has yet to degas.

108

"Ecological Lessons Learned 30 Years After Mount Saint Helens...  

NLE Websites -- All DOE Office Websites (Extended Search)

MBG AUDITORIUM "Ecological Lessons Learned 30 Years After Mount Saint Helens", Dr. Virginia Dale, Oak Ridge National Laboratory http:mediacentral.princeton.eduid0bi7ab6iz...

109

Surface Mounted Under Counter Dimmable LED Strip-STR8  

Science Conference Proceedings (OSTI)

The product under assessment is an advanced lighting technologya controllable, surface mounted under-counter light emitting diode (LED) strip lighting system that is designed to provide various levels of direct and indirect white light.

2008-06-12T23:59:59.000Z

110

North Wind 4-kW wind-system development. Phase II. Fabrication and test  

DOE Green Energy (OSTI)

This report presents the results of Phase II (testing and fabrication) of a program funded by the US Department of Energy to design, fabricate, and test a cost-effective wind system in the 3 to 6 kW class. During Phase II, using the design developed during Phase I, a prototype 4 kW machine was fabricated and tested in Waitsfield, Vermont. Several problems were encountered and subsequently analyzed. Design modifications, including the use of a larger alternator, are described. Test performed by North Wind and by Rockwell International (which monitored the program) demonstrated the predicted performance characteristics and the validity of the North Wind design.

Lynch, J.; Coleman, C.; Mayer, D.J.

1983-01-01T23:59:59.000Z

111

Wind Energy Project Mount Wachusett Community College Gardner, Massachusetts  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Wind Energy Project Mount Wachusett Community College Gardner, Massachusetts ______________________________________________ Final Environmental Assessment December 2009 DOE/EA# 1661 U.S. Department of Energy Golden Field Office National Renewable Energy Laboratory 1617 Cole Boulevard Golden, CO 80401 Wind Energy Project Mount Wachusett Community College Final Environmental Assessment Gardner, Massachusetts _________________________________________________________________________ ____________________________________________________________________ i CHAPTER 1 INTRODUCTION -------------------------------------------------------- 1 1.1 National Environmental Policy Act/Massachusetts Environmental Policy Act .............................................................................................................1

112

PN1C-F.172a DEPARTAIENT OF ENERGY EERE PROJECT MANAGEMENT CENTER  

NLE Websites -- All DOE Office Websites (Extended Search)

water systems at eight school districts. All systems will be equal to or less than 30 kilowatts (kW) and will be roof mounted or ground mounted systems. If the systems are...

113

Transmission Line Grounding  

Science Conference Proceedings (OSTI)

In 2008, the Electric Power Research Institute (EPRI) published a comprehensive grounding report. Published in two parts, the report covered the theoretical and practical aspects of transmission line grounding practices. To further improve the tools available for grounding analysis, an investigation into practical ways to calculate the fault current distribution and ground potential rise of the transmission line grounding system was conducted. Furthermore, a survey of utilities has documented industry pr...

2011-12-23T23:59:59.000Z

114

Hanford Sludge Treatment Project 105-KW Final Safety Analysis Report Review, August 2011  

NLE Websites -- All DOE Office Websites (Extended Search)

Site Visit Report Site Visit Report Sludge Treatment Project 105-KW Final Safety Analysis Report Review May 2011 August 2011 Office of Enforcement and Oversight Office of Health, Safety and Security U.S. Department of Energy Table of Contents 1.0 Introduction ............................................................................................................................................ 1 2.0 Background ............................................................................................................................................ 1 3.0 Scope ...................................................................................................................................................... 1 4.0 Results .................................................................................................................................................... 2

115

Hanford Sludge Treatment Project 105-KW Final Safety Analysis Report Review, August 2011  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Site Visit Report Site Visit Report Sludge Treatment Project 105-KW Final Safety Analysis Report Review May 2011 August 2011 Office of Enforcement and Oversight Office of Health, Safety and Security U.S. Department of Energy Table of Contents 1.0 Introduction ............................................................................................................................................ 1 2.0 Background ............................................................................................................................................ 1 3.0 Scope ...................................................................................................................................................... 1 4.0 Results .................................................................................................................................................... 2

116

Ris-R-1480(EN) Stand-alone version of the 11kW Gaia  

E-Print Network (OSTI)

This report is part of the reporting done as part of the project "The Gaia wind turbine applied in wind diesel or all the diesel power. The requirement is that the wind power system in manyRisø-R-1480(EN) Stand-alone version of the 11kW Gaia wind turbine Henrik Bindner Pedro A.C. Rosas

117

225-kW Dynamometer for Testing Small Wind Turbine Components: Preprint  

SciTech Connect

This paper describes NREL's new 225-kW dynamometer facility that is suitable for testing a variety of components and subsystems for small wind turbines and discusses opportunities for industry partnerships with NREL for use of the facility.

Green, J.

2006-06-01T23:59:59.000Z

118

Design considerations of a 15kW heat exchanger for the CSPonD Project  

E-Print Network (OSTI)

The objective of this work was to develop a 15 kW heat exchanger model for the CSPonD molten salt receiver that will shuttle the molten salt's thermal energy for conversion to electric power. A heat extraction system ...

Adames, Adrian A

2010-01-01T23:59:59.000Z

119

100 kW CC-OTEC Plant and Deep Ocean water Applications  

E-Print Network (OSTI)

Examine multiple usage of DSW Yokogawa Electric Produce & set up electricity & control system Plant the electric grid for the first time in 15 years in the world. #12;IOES (Institute of Ocean Energy, Saga Univ.) Experiments and Demonstration by IOES (Institute of Ocean Energy, Saga University) 30 kW Electricity

120

Radioactive air emissions notice of construction fuel removal for 105-KW Basin  

Science Conference Proceedings (OSTI)

This document serves as a Notice of Construction (NOC), pursuant to the requirements of Washington Administrative Code (WAC) 246-247-060, and as a request for approval to construct, pursuant to 40 Code of Federal Regulations (CFR) 61.96, for the modifications, installation of new equipment, and fuel removal and sludge relocation activities at 105-KW Basin. The purpose of the activities described in this NOC is to enable the eventual retrieval and transport of the fuel for processing. The fuel retrieval and transport will require an integrated water treatment system for which performance specifications have been developed. These specifications are currently in the procurement process. Following procurement (and before installation of this system and the handling of fuel) design details will be provided to Washington State Department of Health (WDOH). The 105-K West Reactor (105-KW) and its associated spent nuclear fuel (SNF) storage basin were constructed in the early 1950s and are located on the Hanford Site in the 100-K Area about 1,400 feet from the Columbia River. The 105-KW Basin contains 964 Metric Tons of SNF stored under water in approximately 3,800 closed canisters. This SNF has been stored for varying periods of time ranging from 8 to 17 years. The 105-KW Basin is constructed of concrete with an epoxy coating and contains approximately 1.3 million gallons of water with an asphaltic membrane beneath the pool. Although the 105-KW Basin has not been known to leak, the discharge chute and associated construction joint have been isolated from the rest of the basin by metal isolation barriers. This was a precautionary measure, to mitigate the consequences of a seismic event. The proposed modifications described are scheduled to begin in calendar year 1997.

Hays, C.B.

1997-05-29T23:59:59.000Z

Note: This page contains sample records for the topic "kw ground mounted" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Fractional-Slot Surface Mounted PM Motors with Concentrated Windings for HEV Traction Drives  

Science Conference Proceedings (OSTI)

High-power density and efficiency resulting from elimination of rotor windings and reduced magnetic-flux losses have made the rare earth permanent magnet (PM) motor a leading candidate for the Department of Energy's Office of FreedomCAR and Vehicle Technologies (FCVTs) traction drive motor. These traction drives are generally powered by radial-gap motors, having the magnets on or embedded in a rotating cylinder separated from the inside surface of a slotted cylindrical stator by an annular gap. The two main types of radial-gap PM rotors are those with magnets mounted on the surface of a supporting back iron, called PM surface mounted (PMSM) motors, and those with magnets mounted in slots in the rotor, called interior PM (IPM) motors. Most early PM motor research was on the PMSM motor, which was thought to have an inherently low stator inductance. A low stator inductance can lead to currents dangerously exceeding rated current as the back-emf across the inductance increases with speed; consequently, part of the attempted solution has been to increase the stator inductance to reduce the rate of current rise. Although analysis suggested that there should be no problem designing sufficiently high stator inductance into PMSMs, attempts to do so were often not successful and a motor design was sought that would have a higher intrinsic inductance. Commercial research at Toyota has focused on IPM motors because they can achieve a high-saliency ratio, which helps them operate over a high constant power speed ratio (CPSR), but they are more difficult to fabricate. The Oak Ridge National Laboratory's (ORNL) position has been to continue research on brushless direct current (dc) motors (BDCMs) because of ease of fabrication and increased power output. Recently there has been a revival of interest in a fractional-slot PMSMs [15] made with concentrated windings because they possess three important features. First, they can increase the motor's inductance sufficiently to reduce the characteristic current to value of the rated current, which will enable them to operate at high CPSR. This feature also limits short-circuit fault currents. Second, their segmented structure simplifies assembly problems and is expected to reduce assembly costs. Third, the back-emf waveform is nearly sinusoidal with low cogging. To examine in depth this design ORNL entered into a collaborative agreement with the University of Wisconsin to build and test a 6 kW laboratory demonstration unit. Design, fabrication, and testing of the unit to 4000 rpm were completed during FY 2005. The motor will be sent to ORNL to explore ways to control its inverter to achieve higher efficiency during FY 2006. This paper first reviews the concept of characteristic current and what is meant by optimal flux weakening. It then discusses application of the fractional-slot concentrated winding technique to increase the d-axis inductance of a PMSM showing how this approach differs from an integral-slot motor with sinusoidal-distributed windings. This discussion is followed by a presentation of collaborative analyses and comparison with the University of Wisconsin's measured data on a 6 kW, 36-slot, 30-pole motor with concentrated windings. Finally ORNL presents a PMSM design with integral-slot windings that appears to meet the FreedomCAR Specifications, but has some disadvantages. Further collaboration with the University of Wisconsin is planned for FY 2006 to design a motor that meets FreedomCAR specifications.

Bailey, J.M.

2005-10-24T23:59:59.000Z

122

Mount Wachusetts Community College Wind Project | Open Energy Information  

Open Energy Info (EERE)

Wachusetts Community College Wind Project Wachusetts Community College Wind Project Jump to: navigation, search Name Mount Wachusetts Community College Wind Project Facility Mount Wachusetts Community College Wind Project Sector Wind energy Facility Type Community Wind Facility Status In Service Owner Mount Wachusetts Community College Developer Mount Wachusetts Community College Energy Purchaser Mount Wachusetts Community College Location Gardner MA Coordinates 42.58855651°, -71.98396683° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":42.58855651,"lon":-71.98396683,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

123

City of Rocky Mount, North Carolina (Utility Company) | Open Energy  

Open Energy Info (EERE)

Mount, North Carolina (Utility Company) Mount, North Carolina (Utility Company) Jump to: navigation, search Name City of Rocky Mount Place North Carolina Utility Id 16226 Utility Location Yes Ownership M NERC Location SERC NERC SERC Yes ISO Other Yes Activity Distribution Yes References EIA Form EIA-861 Final Data File for 2010 - File1_a[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. Utility Rate Schedules Grid-background.png Area Lighting - 1000W MH Lighting Area Lighting - 1000W MV Lighting Area Lighting - 100W MH Lighting Area Lighting - 100W MH (SE) Lighting Area Lighting - 100W SV Lighting Area Lighting - 100W SV (SE) Lighting Area Lighting - 1500W MH Lighting Area Lighting - 150W SV Lighting Area Lighting - 175W MH Lighting

124

City of Mount Vernon, Missouri (Utility Company) | Open Energy Information  

Open Energy Info (EERE)

Mount Vernon Mount Vernon Place Missouri Utility Id 13040 Utility Location Yes Ownership M NERC Location SPP NERC SPP Yes Activity Distribution Yes References EIA Form EIA-861 Final Data File for 2010 - File1_a[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. Utility Rate Schedules Grid-background.png Industrial Industrial Non-Residential Commercial Non-Residential (with demand meters) Industrial Residential Residential Average Rates Residential: $0.0838/kWh Commercial: $0.0836/kWh Industrial: $0.0717/kWh References ↑ "EIA Form EIA-861 Final Data File for 2010 - File1_a" Retrieved from "http://en.openei.org/w/index.php?title=City_of_Mount_Vernon,_Missouri_(Utility_Company)&oldid=409982"

125

Mount Princeton Area Space Heating Low Temperature Geothermal Facility |  

Open Energy Info (EERE)

Area Space Heating Low Temperature Geothermal Facility Area Space Heating Low Temperature Geothermal Facility Jump to: navigation, search Name Mount Princeton Area Space Heating Low Temperature Geothermal Facility Facility Mount Princeton Area Sector Geothermal energy Type Space Heating Location Mount Princeton, Colorado Coordinates 38.749167°, -106.2425° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[]}

126

Electrical Subsurface Grounding Analysis  

SciTech Connect

The purpose and objective of this analysis is to determine the present grounding requirements of the Exploratory Studies Facility (ESF) subsurface electrical system and to verify that the actual grounding system and devices satisfy the requirements.

J.M. Calle

2000-11-01T23:59:59.000Z

127

Rolling contact mounting arrangement for a ceramic combustor  

DOE Patents (OSTI)

A combustor assembly having a preestablished rate of thermal expansion is mounted within a gas turbine engine housing having a preestablished rate of thermal expansion being greater than the preestablished rate of thermal expansion of the combustor assembly. The combustor assembly is constructed of a inlet end portion, a outlet end portion and a plurality of combustor ring segments positioned between the end portions. A mounting assembly is positioned between the combustor assembly and the gas turbine engine housing to allow for the difference in the rate of thermal expansion while maintaining axially compressive force on the combustor assembly to maintain contact between the separate components.

Boyd, Gary L. (328 Sneath Way, Alpine, CA 91901); Shaffer, James E. (1780 Geronimo Tr., Maitland, FL 32751)

1995-01-01T23:59:59.000Z

128

Rolling contact mounting arrangement for a ceramic combustor  

DOE Patents (OSTI)

A combustor assembly having a preestablished rate of thermal expansion is mounted within a gas turbine engine housing having a preestablished rate of thermal expansion being greater than the preestablished rate of thermal expansion of the combustor assembly. The combustor assembly is constructed of a inlet end portion, a outlet end portion and a plurality of combustor ring segments positioned between the end portions. A mounting assembly is positioned between the combustor assembly and the gas turbine engine housing to allow for the difference in the rate of thermal expansion while maintaining axially compressive force on the combustor assembly to maintain contact between the separate components. 3 figs.

Boyd, G.L.; Shaffer, J.E.

1995-10-17T23:59:59.000Z

129

United Technologies Research Center 8-kW prototype wind system. Final test report  

DOE Green Energy (OSTI)

The United Technologies Research Center 8 kW prototype wind system underwent testing at the Rocky Flats Small Wind Systems Test Center from April 1980 through August 1980. During atmospheric testing, the machine survived wind speeds of 30.8 m/s (69 mph) without incurring damage and proved it was capable of meeting the design specification for power production (8 kW at 9 m/s - 20 mph). Erratic cycling of the generator speed detector was the only operational problem encountered. Vibration tests indicated the first and second bending modes of the tower were excited during actual machine operation, but modifications were not required. Noise measurements revealed that sound pressure levels of the UTRC are within an acceptable range and should pose no barriers to machine use.

Higashi, K. K.

1981-09-01T23:59:59.000Z

130

200 kW, 800 MHz transmitter system for lower hybrid heating  

SciTech Connect

This paper describes a new rf heating system which has just been completed and is now operational on the ATC machine. The system utilizes four UHF TV klystrons to generate at least 200 kW of power at a frequency of 800 MHz. Pulse widths can be varied from 20 $mu$sec up to 20 msec. A radar type floating deck modulator along with photo-optical transmitting and receiving devices have been incorporated into the system to provide the pulse fidelity and versatility which characterizes this equipment. Modular construction was emphasized in the design, when possible, to reduce maintenance and down time in the advent of component falilure. Hybrid combining techniques are utilized in order to provide two 100 kW feeds into the machine. (auth)

Deitz, A.

1975-01-01T23:59:59.000Z

131

MHK Projects/Evopod E35 35kW grid connected demonstrator | Open Energy  

Open Energy Info (EERE)

E35 35kW grid connected demonstrator E35 35kW grid connected demonstrator < MHK Projects Jump to: navigation, search << Return to the MHK database homepage Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":5,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"500px","height":"350px","centre":false,"title":"","label":"","icon":"File:Aquamarine-marker.png","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":55.3028,"lon":-5.59772,"alt":0,"address":"","icon":"http:\/\/prod-http-80-800498448.us-east-1.elb.amazonaws.com\/w\/images\/7\/74\/Aquamarine-marker.png","group":"","inlineLabel":"","visitedicon":""}]}

132

Field Evaluation of the 200 kW PAFC Unit at the Pittsburgh International Airport  

Science Conference Proceedings (OSTI)

Distributed generation, particularly in combination with the benefits of fuel cells, is attracting increasing utility industry interest. This report details more than 20,000 hours of automatic, unattended operation of an ONSI 200 kW phosphoric acid fuel cell at the Pittsburgh International Airport. Also included are installation, operation, and performance data on more than twenty other units in the U.S. ONSI fleet.

1997-09-30T23:59:59.000Z

133

Enertech 15-kW wind-system development. Phase II. Fabrication and test  

DOE Green Energy (OSTI)

This Phase II report presents a description of the Enertech 15 kW prototype wind system hardware fabrication; results of component tests; and results of preliminary testing conducted at Norwich, VT and the RF Wind Energy Research Center. In addition, the assembly sequence is documented. During testing, the unit experienced several operational problems, but testing proved the design concept and demonstrated the system's ability to meet the contract design specifications for power output.

Zickefoose, C.R.

1982-12-01T23:59:59.000Z

134

50 kW PEM Fuel Cell System Design, Fabrication, and Test: System Design -- Final Report  

Science Conference Proceedings (OSTI)

This final report describes the results of a development program funded jointly by the U.S. Department of Energy, Arthur D. Little, and EPRIsolutions. The effort was aimed at the conceptual design and optimization of a 50 kW commercial power system, using advanced proton exchange (or polymer electrolyte) membrane fuel cell (PEMFC) technology and the verification of key design parameters. (Note: This design effort addresses some of the key technical issues faced by the developers of commercial-scale PEMFC...

2000-12-11T23:59:59.000Z

135

Performance of 350kW photovoltaic power system for Saudi Arabian villages after 30 months  

Science Conference Proceedings (OSTI)

The installation and checkout of the 350kW PV system was completed in September 1981. Since then this system has operated satisfactorily over the past two and half years and has experienced very little downtime. The system has a rather unique capability to operate in standalone or any of several cogeneration modes. This paper presents an update of the system performance with emphasis on the photovoltaic field. Research effort being implemented for the next two years are also briefly summarized.

Koshaim, B.; Al-Sani, A.; Huraib, F.; Imamura, M.S.; Salim, A.

1984-05-01T23:59:59.000Z

136

Distributed Generation Study/615 kW Waukesha Packaged System | Open Energy  

Open Energy Info (EERE)

kW Waukesha Packaged System kW Waukesha Packaged System < Distributed Generation Study Jump to: navigation, search Study Location Des Plaines, Illinois Site Description Testing Laboratory Study Type Laboratory Test Technology Internal Combustion Engine Prime Mover Waukesha VGF 36GLD Heat Recovery Systems Sondex PHE-Type SL140-TM-EE-190, Sondex PHE-Type SL140-TM-EE-150, Cain UTR1-810A17.5SSP Fuel Natural Gas System Installer GTI System Enclosure Outdoor System Application Combined Heat and Power Number of Prime Movers 1 Stand-alone Capability None Power Rating 615 kW0.615 MW 615,000 W 615,000,000 mW 6.15e-4 GW 6.15e-7 TW Nominal Voltage (V) 480 Heat Recovery Rating (BTU/hr) 2500000 Cooling Capacity (Refrig/Tons) 90 Origin of Controller 3rd Party Off-the-Shelf Component Integration Factory Integrated

137

Gainesville Regional Utilities - Solar Feed-In Tariff | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Gainesville Regional Utilities - Solar Feed-In Tariff Gainesville Regional Utilities - Solar Feed-In Tariff Gainesville Regional Utilities - Solar Feed-In Tariff < Back Eligibility Commercial Fed. Government Industrial Institutional Local Government Nonprofit Residential Schools State Government Tribal Government Savings Category Solar Buying & Making Electricity Program Info Start Date 03/01/2009 State Florida Program Type Performance-Based Incentive Rebate Amount 2013 Contracts: Rooftop- or pavement-mounted systems Ground-mounted systems Rooftop- or pavement-mounted systems >10kW to 300kW: $0.18/kWh Ground-mounted systems >10kW to 25kW: $0.18/kWh Ground-mounted systems >25kW to 1,000kW: $0.15/kWh Provider Gainesville Regional Utilities NOTE: This program will re-open to new applicants from January 4, 2013

138

Better than blasting for blackwells. [Tractor-mounted ripper  

SciTech Connect

On opencasting, quarrying and rock removal generally, a tractor-mounted ripper is usually felt to be safer and quieter than drilling and blasting with high explosive. Helped by Newram Plant Limited, C.A. Blackwell (Contracts) Limited are seeing if this really is so and if ripping also has any economic and performance advantages.

1979-10-01T23:59:59.000Z

139

Improved ADCP Performance Using a Hydrodynamically Designed Boom Mount  

Science Conference Proceedings (OSTI)

This paper presents the results of the design and testing of a hydrodynamic mount for a direct-reading 150-kHz acoustic Doppler current profiler (ADCP) operated over the side of a small inshore vessel in transect mode (i.e., while steaming). The ...

E. B. Colbourne; J. Helbig; D. Cumming

1993-08-01T23:59:59.000Z

140

Mixed reality with multimodal head-mounted pico projector  

Science Conference Proceedings (OSTI)

Many kinds of displays can be used for augmented reality (AR). Multimodal head-mounted pico projector is a concept, which is little explored for AR. It opens new possibilities for wearable displays. In this paper we present our proof-of-concept prototype ... Keywords: augmented reality, mixed reality, multimodality, pico projector, wearable displays

Antti Sand; Ismo Rakkolainen

2013-03-01T23:59:59.000Z

Note: This page contains sample records for the topic "kw ground mounted" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Electrical grounding prong socket  

SciTech Connect

The invention is a socket for a grounding prong used in a three prong electrical plug and a receptacle for the three prong plug. The socket being sufficiently spacious to prevent the socket from significantly stretching when a larger, U-shaped grounding prong is inserted into the socket, and having a ridge to allow a snug fit when a smaller tubular shape grounding prong is inserted into the socket.

Leong, Robert (Dublin, CA)

1991-01-01T23:59:59.000Z

142

Predaceous Ground Beetles  

E-Print Network (OSTI)

Predaceous ground beetles can be a nuisance to homeowners, especially when they are numerous. This publication describes the beetles and discusses ways to prevent and treat them.

Sansone, Chris; Minzenmayer, Rick

2003-06-30T23:59:59.000Z

143

Substation grounding programs  

SciTech Connect

This document is a users manual and applications guide for the software package SGA. This package comprises four computer programs, namely SOMIP, SMECC, SGSYS, and TGRND. The first three programs are analysis models which are to be used in the design process of substation grounding systems. The fourth program, TGRND, is an analysis program for determining the transient response of a grounding system. This report, Volume 3, is a users manual and an installation and validation manual for the computer program SGSYS (Substation Grounding SYStem Analysis Program). This program analyzes the substation ground field given the total electric current injected into the ground field and the design of the grounding system. Standard outputs of the program are (1) total ground resistance, (2) step voltage, (3) touch voltage, (4) voltages on a grid of points, (5) voltage profile along straight lines, (6) transfer voltages, (7) ground potential rise, (8) body currents, (9) step voltage profile along straight lines, and (10) touch voltage profile along straight lines. This program can be utilized in an interactive or batch mode. In the interactive mode, the user defines the grounding system geometry, soil parameters, and output requests interactively, with the use of a user friendly conversational program. The users manual describes data requirements and data preparation procedures. An appendix provides forms which facilitate data collection procedures. The installation and validation manual describes the computer files which make up the program SGSYS and provides a test case for validation purposes.

Meliopoulos, A.P.S. (Georgia Inst. of Tech., Atlanta, GA (United States). Electric Power Lab.)

1992-05-01T23:59:59.000Z

144

4 kW Test of Solid Oxide Electrolysis Stacks with Advanced Electrode-Supported Cells  

DOE Green Energy (OSTI)

A new test stand has been developed at the Idaho National Laboratory for multi-kW testing of solid oxide electrolysis stacks. This test stand will initially be operated at the 4 KW scale. The 4 kW tests will include two 60-cell stacks operating in parallel in a single hot zone. The stacks are internally manifolded with an inverted-U flow pattern and an active area of 100 cm2 per cell. Process gases to and from the two stacks are distributed from common inlet/outlet tubing using a custom base manifold unit that also serves as the bottom current collector plate. The solid oxide cells incorporate a negative-electrode-supported multi-layer design with nickel-zirconia cermet negative electrodes, thin-film yttria-stabilized zirconia electrolytes, and multi-layer lanthanum ferrite-based positive electrodes. Treated metallic interconnects with integral flow channels separate the cells and electrode gases. Sealing is accomplished with compliant mica-glass seals. A spring-loaded test fixture is used for mechanical stack compression. Due to the power level and the large number of cells in the hot zone, process gas flow rates are high and heat recuperation is required to preheat the cold inlet gases upstream of the furnace. Heat recuperation is achieved by means of two inconel tube-in-tube counter-flow heat exchangers. A current density of 0.3 A/cm2 will be used for these tests, resulting in a hydrogen production rate of 25 NL/min. Inlet steam flow rates will be set to achieve a steam utilization value of 50%. The 4 kW test will be performed for a minimum duration of 1000 hours in order to document the long-term durability of the stacks. Details of the test apparatus and initial results will be provided.

J. E. O'Brien; X. Zhang; G. K. Housley; L. Moore-McAteer; G. Tao

2012-06-01T23:59:59.000Z

145

Performance Assessment of the 6kW Ultra Capacitor Based Bonitron Ride-Through System  

Science Conference Proceedings (OSTI)

The objective of this report is to describe and document the operation and performance of the Bonitron adjustable speed drive voltage sag protection device. This report will describe the different tests that were conducted and their results to characterize the Bonitron. The tests that were conducted include voltage sag and swell protection, interruption, re-closure, and life cycle tests. Additional characterization tests will also be discussed. The Bonitron was tested at 100% load using a 7.5kW/10Hp ...

2012-12-31T23:59:59.000Z

146

High Temperature Electrolysis 4 kW Experiment Design, Operation, and Results  

SciTech Connect

This report provides results of long-term stack testing completed in the new high-temperature steam electrolysis multi-kW test facility recently developed at INL. The report includes detailed descriptions of the piping layout, steam generation and delivery system, test fixture, heat recuperation system, hot zone, instrumentation, and operating conditions. This facility has provided a demonstration of high-temperature steam electrolysis operation at the 4 kW scale with advanced cell and stack technology. This successful large-scale demonstration of high-temperature steam electrolysis will help to advance the technology toward near-term commercialization.

J.E. O'Brien; X. Zhang; K. DeWall; L. Moore-McAteer; G. Tao

2012-09-01T23:59:59.000Z

147

Apparatus for mounting photovoltaic power generating systems on buildings  

DOE Patents (OSTI)

Rectangular photovoltaic (PV) modules are mounted on a building roof by mounting stands that are distributed in rows and columns. Each stand comprises a base plate and first and second different height brackets attached to opposite ends of the base plate. Each first and second bracket comprises two module-support members. One end of each module is pivotally attached to and supported by a first module-support member of a first bracket and a second module-support member of another first bracket. At its other end each module rests on but is connected by flexible tethers to module-support members of two different second brackets. The tethers are sized to allow the modules to pivot up away from the module-support members on which they rest to a substantially horizontal position in response to wind uplift forces.

Russell, Miles C. (Lincoln, MA)

2009-08-18T23:59:59.000Z

148

Design of Energy Scavengers Mounted on Rotating Shafts  

E-Print Network (OSTI)

In this paper, a novel energy scavenger is proposed. The scavenger consists of a cantilever beam on which piezoelectric films and a mass are mounted. The mass at the tip of the beam is known as the proof mass and the device is called either an energy scavenger or a beam-mass system. The beam-mass system is mounted on a rotating shaft, where the axis of the shaft is horizontal. A single-degree-of-freedom (SDOF) mathematical model is derived for the scavenger and its properties are carefully examined. From the model, it becomes clear that the rotation of the shaft and gravity cause both parametric excitations and exogenous forces which make the beam-mass system vibrate. Guidelines are provided as how to choose the scavenger parameters in order to have it resonate. Examples are given to illustrate the performance of the proposed scavenger.

Shahruz, S M

2008-01-01T23:59:59.000Z

149

Development of the Platform-Mounted Dynamic Voltage Restorer (PMDVR)  

Science Conference Proceedings (OSTI)

The uninterrupted supply of electrical power is critical for many commercial utility customers with sensitive loads. A voltage sag of a few cycles could cause loss of many thousands of dollars due to lost production from process stoppage and associated clean-up issues. The Platform Mounted Dynamic Voltage Restorer (PMDVR) is a distribution voltage level device that compensates for changes in supply line voltage to maintain acceptable input power to customers.

1998-12-31T23:59:59.000Z

150

Distributed Energy Storage Systems for Padmounted or Pole Mount Transformers  

Science Conference Proceedings (OSTI)

The goal of this project is to define the specifications for distributed energy storage systems in a neighborhood or a community setting also known as a distributed energy storage (DES) system, where they can be co-located with pad-mounted transformers. In 2009, the program collaborated with a utility stakeholder interest group to further enhance functional specifications developed by AEP for such energy storage systems. Initial technology mapping, screening and cost and value analysis have also been con...

2009-12-10T23:59:59.000Z

151

Test probe for surface mounted leadless chip carrier  

DOE Patents (OSTI)

A test probe for a surface mounted leadless chip carrier is disclosed. The probed includes specially designed connector pins which allow size reductions in the probe. A thermoplastic housing provides spring action to ensure good mechanical and electrical contact between the pins and the contact strips of a leadless chip carrier. Other features include flexible wires molded into the housing and two different types of pins alternately placed in the housing. These features allow fabrication of a smaller and simpler test probe.

Meyer, Kerry L. (Raytown, MO); Topolewski, John (Lenexa, KS)

1989-05-23T23:59:59.000Z

152

Concentration system performance degradation in the aftermath of Mount Pinatubo  

Science Conference Proceedings (OSTI)

Major volcanic eruptions occur every few years, but most have little effect on solar radiation or climate. However, in the last ten years two volcanoes have decreased solar radiation and influenced weather at a level that might be expected at the frequency of about once a century. The Mexican volcano El Chichon and the Philippine volcano Mount Pinatubo put 6 and 20 million metric tons of SO{sub 2} in the stratosphere, respectively. SO{sub 2} is converted into H{sub 2}SO{sub 4}, which mixes with water to produce aerosol. Since there is no weather in the stratosphere and the aerosol is small, these aerosol particles remain suspended until coagulation and sedimentation bring them to the troposphere where they are removed by normal wet and dry deposition processes. The extinction in the direct solar irradiance from El Chichon was found to peak during the winter of 1983 at about 11% for northern, mid latitudes. Mount Pinatubo`s peak extinction during 1992 was about 15%. Data from four northern, mid-latitude sites are examined to compare the direct consequences of the volcano`s eruption on the performance of concentrating solar energy systems and the indirect effects that may be associated with Mount Pinatubo`s perturbation of the weather.

Michalsky, J.J.; Perez, R.; Seals, R. [State Univ. of New York, Albany, NY (United States). Atmospheric Sciences Research Center; Ineichen, P. [Geneva Univ. (Switzerland). Groupe de Physique Appliquee

1993-11-01T23:59:59.000Z

153

Ballast-mounted PV arrays: Phase 2 final report  

DOE Green Energy (OSTI)

The expansive flat rooftops of industrial and commercial buildings across America offer the largest, most secure, and potentially least-cost real estate opportunity to install massive amounts of solar photovoltaic generation in the building sector. Unfortunately, mechanical penetration of roofing membranes is very expensive and perceived by building owners and operators to increase the likelihood of leaking. In response Ascension Technology has pioneered the development of low-cost ballasted approaches for mounting PV arrays. Recently, however, we have experienced our first two instances in which strong winds have moved our arrays on rooftops and heightened our interest, and the PV industries' need, to develop zero-penetration mounting techniques that are more secure, yet remain low in cost. In this PV BONUS project, Ascension Technology and its partners addressed wind loading on solar panels and the suitability of using frictional forces between ballast trays and roofing materials to resist PV arrays sliding on rooftops. The primary goal of the project is to capture the potential cost savings made possible by ballast-mounting by showing under what conditions it can satisfy wind loading concerns. A secondary goal is to address a more geographically constrained concern regarding withstanding seismic forces.

Edward C. Kern

2000-03-01T23:59:59.000Z

154

Ballast-mounted PV arrays: Phase 2 final report  

SciTech Connect

The expansive flat rooftops of industrial and commercial buildings across America offer the largest, most secure, and potentially least-cost real estate opportunity to install massive amounts of solar photovoltaic generation in the building sector. Unfortunately, mechanical penetration of roofing membranes is very expensive and perceived by building owners and operators to increase the likelihood of leaking. In response Ascension Technology has pioneered the development of low-cost ballasted approaches for mounting PV arrays. Recently, however, we have experienced our first two instances in which strong winds have moved our arrays on rooftops and heightened our interest, and the PV industries' need, to develop zero-penetration mounting techniques that are more secure, yet remain low in cost. In this PV BONUS project, Ascension Technology and its partners addressed wind loading on solar panels and the suitability of using frictional forces between ballast trays and roofing materials to resist PV arrays sliding on rooftops. The primary goal of the project is to capture the potential cost savings made possible by ballast-mounting by showing under what conditions it can satisfy wind loading concerns. A secondary goal is to address a more geographically constrained concern regarding withstanding seismic forces.

Edward C. Kern

2000-03-01T23:59:59.000Z

155

Wind Turbine Generator System Acoustic Noise Test Report for the Gaia Wind 11-kW Wind Turbine  

DOE Green Energy (OSTI)

This report details the acoustic noise test conducted on the Gaia-Wind 11-kW wind turbine at the National Wind Technology Center. The test turbine is a two- bladed, downwind wind turbine with a rated power of 11 kW. The test turbine was tested in accordance with the International Electrotechnical Commission standard, IEC 61400-11 Ed 2.1 2006-11 Wind Turbine Generator Systems -- Part 11 Acoustic Noise Measurement Techniques.

Huskey, A.

2011-11-01T23:59:59.000Z

156

History of Residential Grounding  

Science Conference Proceedings (OSTI)

This report describes the development of residential electrical service grounding practices in the United States. The report focuses on the history of the National Electrical Code (NEC), which prescribes standards for wiring practices in residences, including grounding of the building electrical service.

2002-09-19T23:59:59.000Z

157

Ways of grounding imagination  

Science Conference Proceedings (OSTI)

This paper discusses and evaluates use of different participatory design methods in relation to addressing the challenge of grounding imagination. It presents reflections on the use of three participatory design methods, deployed in the WorkSpace project: ... Keywords: PD methods, analytical triangulation, bricolage, future laboratory, grounding imagination, in-situ prototyping experiments

Monika Büscher; Mette Agger Eriksen; Jannie Friis Kristensen; Preben Holst Mogensen

2004-07-01T23:59:59.000Z

158

Ground Motion Workshop  

NLE Websites -- All DOE Office Websites (Extended Search)

2nd Advanced ICFA Beam Dynamics Workshop 2nd Advanced ICFA Beam Dynamics Workshop on Ground Motion in Future Accelerators November 6 - 9, 2000 SLAC Coordinators: Andrei Seryi & Tor Raubenheimer Proceedings Updated June 26, 2001 Agenda and Presentations Workshop photos Summaries Useful links Poster Goals Introduction to the problems Structure Registration Registered participants Committees Location, Accommodations and Travel Workshop on Ground Motion in Future Accelerators A workshop was held at SLAC that was devoted to ground motion and its effects on future accelerators. Ground motion and vibration can be a limiting effect in synchrotron light sources, hadron circular colliders, and electron/positron linear colliders. Over the last several years, there has been significant progress in the understanding of the ground motion and its effects, however, there are

159

Solar energy collector for mounting over windows of buildings for space heating thereof  

SciTech Connect

The ornamental design for a solar energy collector for mounting over windows of buildings for space heating thereof, as shown.

Arrington, P.M.

1982-09-07T23:59:59.000Z

160

METHOD OF LOCATING GROUNDS  

DOE Patents (OSTI)

ABS>This patent presents a method for locating a ground in a d-c circult having a number of parallel branches connected across a d-c source or generator. The complete method comprises the steps of locating the ground with reference to the mildpoint of the parallel branches by connecting a potentiometer across the terminals of the circuit and connecting the slider of the potentiometer to ground through a current indicating instrument, adjusting the slider to right or left of the mildpoint so as to cause the instrument to indicate zero, connecting the terminal of the network which is farthest from the ground as thus indicated by the potentiometer to ground through a condenser, impressing a ripple voltage on the circuit, and then measuring the ripple voltage at the midpoint of each parallel branch to find the branch in which is the lowest value of ripple voltage, and then measuring the distribution of the ripple voltage along this branch to determine the point at which the ripple voltage drops off to zero or substantially zero due to the existence of a ground. The invention has particular application where a circuit ground is present which will disappear if the normal circuit voltage is removed.

Macleish, K.G.

1958-02-11T23:59:59.000Z

Note: This page contains sample records for the topic "kw ground mounted" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Demonstrating the Feasibility of Molten Aluminum for Destroying Polymeric Encapsulants in SNG-Bearing Metallographic Mounts  

SciTech Connect

DOE-owned spent nuclear fuel (SNF) rods have been cross sectioned and mounted for metallography throughout the history of nuclear reactors. Many hundreds of these ''met mounts'' have accumulated in storage across the DOE complex. However, because of potential hydrogen generation from radiolysis of the polymeric encapsulants, the met mounts are problematic for eventual disposal in a geologic repository.

Dan Stout; Scott Ploger

2004-08-31T23:59:59.000Z

162

Development of a 402.5 MHz 140 kW Inductive Output Tube  

SciTech Connect

This report contains the results of Phase I of an SBIR to develop a Pulsed Inductive Output Tube (IOT) with 140 kW at 400 MHz for powering H-proton beams. A number of sources, including single beam and multiple beam klystrons, can provide this power, but the IOT provides higher efficiency. Efficiencies exceeding 70% are routinely achieved. The gain is typically limited to approximately 24 dB; however, the availability of highly efficient, solid state drivers reduces the significance of this limitation, particularly at lower frequencies. This program initially focused on developing a 402 MHz IOT; however, the DOE requirement for this device was terminated during the program. The SBIR effort was refocused on improving the IOT design codes to more accurately simulate the time dependent behavior of the input cavity, electron gun, output cavity, and collector. Significant improvement was achieved in modeling capability and simulation accuracy.

R. Lawrence Ives; Michael Read, Robert Jackson

2012-05-09T23:59:59.000Z

163

DOE: T-O-D rates shift kWh and kW  

SciTech Connect

Technical report:In 1975, FEA, in cooperation with state and local utility authorities, initiated a series of field projects that collected electricity usage data under new electric utility rate designs and load management techniques. Individual projects included a wide range of load-management and electricity rate design alternatives, with emphasis on several forms of time-of-day rates. The program is now funded by the U.S. Dept. of Energy. Objectives of the program, kWh usage effects, kw demand effects, and sources of the load changes are discussed. Initial results indicate actual or effective shifts in electricity consumption from peak to off-peak periods, and reductions in diversified demand coincident with system peaks. (10 graphs)

Johnson, C.R.; Mintz, S.

1978-11-15T23:59:59.000Z

164

A 350 MHz, 200 kW CW, Multiple Beam Inductive Output Tube - Final Report  

SciTech Connect

This program developed a 200 kW CW, 350 MHz, multiple beam inductive output tube (MBIOT) for driving accelerator cavities. The MBIOT operates at 30 kV with a gain of 23 dB. The estimated efficiency is 70%. The device uses seven electron beams, each transmitting 1.4 A of current. The tube is approximately six feet long and weighs approximately 400 lbs. The prototype device will be evaluated as a potential RF source for the Advanced Photon Source at Argonne National Laboratory (ANL). Because of issues related to delivery of the electron guns, it was not possible to complete assembly and test of the MBIOT during the Phase II program. The device is being completed with support from Calabazas Creek Research, Inc., Communications & Power Industries, LLC. and the Naval Surface Weapons Center (NSWC) in Dahlgren, VA. The MBIOT will be initially tested at NSWC before delivery to ANL. The testing at NSWC is scheduled for February 2013.

R.Lawrece Ives; George Collins; David Marsden Michael Read; Edward Eisen; Takuchi Kamura, Philipp Borchard

2012-11-28T23:59:59.000Z

165

Management Of Hanford KW Basin Knockout Pot Sludge As Spent Nuclear Fuel  

SciTech Connect

CH2M HILL Plateau Remediation Company (CHPRC) and AREVA Federal Services, LLC (AFS) have been working collaboratively to develop and deploy technologies to remove, transport, and interim store remote-handled sludge from the 10S-K West Reactor Fuel Storage Basin on the U.S. Department of Energy (DOE) Hanford Site near Richland, WA, USA. Two disposal paths exist for the different types of sludge found in the K West (KW) Basin. One path is to be managed as Spent Nuclear Fuel (SNF) with eventual disposal at an SNF at a yet to be licensed repository. The second path will be disposed as remote-handled transuranic (RH-TRU) waste at the Waste Isolation Pilot Plant (WIPP) in Carlsbad, NM. This paper describes the systems developed and executed by the Knockout Pot (KOP) Disposition Subproject for processing and interim storage of the sludge managed as SNF, (i.e., KOP material).

Raymond, R. E. [CH2M HIll Plateau Remediation Company, Richland, WA (United States); Evans, K. M. [AREVA, Avignon (France)

2012-10-22T23:59:59.000Z

166

Enertech 2-kW high-reliability wind system. Phase II. Fabrication and testing  

SciTech Connect

A high-reliability wind machine rated for 2 kW in a 9 m/s wind has been developed. Activities are summarized that are centered on the fabrication and testing of prototypes of the wind machine. The test results verified that the wind machine met the power output specification and that the variable-pitch rotor effectively controlled the rotor speed for wind speeds up to 50 mph. Three prototypes of the wind machine were shipped to the Rocky Flats test center in September through November of 1979. Work was also performed to reduce the start-up wind speed. The start-up wind speed to the Enertech facility has been reduced to 4.5 m/s.

Cordes, J.A.; Johnson, B.A.

1981-06-01T23:59:59.000Z

167

Test Results From The Idaho National Laboratory 15kW High Temperature Electrolysis Test Facility  

DOE Green Energy (OSTI)

A 15kW high temperature electrolysis test facility has been developed at the Idaho National Laboratory under the United States Department of Energy Nuclear Hydrogen Initiative. This facility is intended to study the technology readiness of using high temperature solid oxide cells for large scale nuclear powered hydrogen production. It is designed to address larger-scale issues such as thermal management (feed-stock heating, high temperature gas handling, heat recuperation), multiple-stack hot zone design, multiple-stack electrical configurations, etc. Heat recuperation and hydrogen recycle are incorporated into the design. The facility was operated for 1080 hours and successfully demonstrated the largest scale high temperature solid-oxide-based production of hydrogen to date.

Carl M. Stoots; Keith G. Condie; James E. O'Brien; J. Stephen Herring; Joseph J. Hartvigsen

2009-07-01T23:59:59.000Z

168

Verification test of a 25kW class SOFC cogeneration system  

DOE Green Energy (OSTI)

Osaka Gas and Tokyo Gas have high expectations for natural-gas-fueled Solid Oxide Fuel Cell (SOFC) cogeneration systems. SOFC offers many advantages for on-site cogeneration systems, such as high electrical efficiency, high quality by-product heat and low emissions. They are now executing a joint development program with Westinghouse Electric Corporation (hereinafter called as WELCO). This program is aimed to verify a 25kW class SOFC cogeneration system. This system, which was modified by replacing previous zirconia porous support tube cells (PST cells) with newly designed air electrode supported cells (AES cells), commenced operation on March 21, 1995. The system has been successfully operated for 13,100 hours as of February 7, 1997. This paper presents the performance evaluation of the new AES cells and the results of system operation at WELCO.

Yokoyama, H. [Osaka Gas Company Limited (Japan). Fuel Cell Development Dept.; Miyahara, A. [Tokyo Gas Company Limited (Japan). Duel Cell R& D Dept.; Veyo, S.E. [Westinghouse Electric Corp., Pittsburgh, PA (United States). Westinghouse Science & Technology Center

1997-12-31T23:59:59.000Z

169

Commercialization of a 2.5kW Utility Interactive Inverter for Distributed Generation  

SciTech Connect

Through this project, Advanced Energy Conversion (AEC) has developed, tested, refined and is preparing to commercialize a 2.5kW utility-interactive inverter system for distributed generation. The inverter technology embodies zero-voltage switching technology that will ultimately yield a system that is smaller, less expensive and more efficient than existing commercial technologies. This program has focused on commercial success through careful synthesis of technology, market-focus and business development. AEC was the primary participant. AEC is utilizing contract manufacturers in the early stages of production, allowing its technical staff to focus on quality control issues and product enhancements. The objective of this project was to bring the AEC inverter technology from its current pre-production state to a commercial product. Federal funds have been used to build and test production-intent inverters, support the implementation of the commercialization plan and bring the product to the point of UL certification.

Torrey, David A.

2006-05-26T23:59:59.000Z

170

Solar concentration of 50,000 achieved with output power approaching 1 kW  

SciTech Connect

The authors have achieved a 50,000 {+-} 3,000 times concentration of sunlight using a unique dielectric nonimaging concentrator in an experiment performed at the National Renewable Energy Laboratory. The scale of the experiment is several times larger than that of previous experiments. Total output power approaching 1 kW passes through a 4.6 mm diameter aperture. An extractor tip is added to the concentrator profile which allows measurement of flux levels using an air calorimeter. This new device has the potential to allow the use of dielectric concentrators at larger scale for thermal electric power generation. The authors report on the implications of this experiment for the future use of dielectric concentrators.

Jenkins, D.; Winston, R.; Bliss, J.; O`Gallagher, J. [Univ. of Chicago, IL (United States); Lewandowski, A.; Bingham, C. [National Renewal Energy Lab., Golden, CO (United States)

1996-08-01T23:59:59.000Z

171

Installation system for integral mounting of thermal or photovoltaic panels  

Science Conference Proceedings (OSTI)

A unique installation system for mounting solar thermal or photovoltaic solar collector panels as an integral part of a structure is described. The most common example would have the collector array replacing the sheathing and shingles of a roof supported by trusses or rafters on 24 inch centers. The design achieves the goals of a good integral installation which is reliably weathertight, rapid and easy to execute by typical construction workers with little specific extra training and no special tools. All materials and components are commercially available and have proven performance.

Rost, D.F. (Solar Energy Engineering, Poland, OH); Ameduri, G.; Groves, L.

1981-01-01T23:59:59.000Z

172

Test probe for surface mounted leadless chip carrier  

DOE Patents (OSTI)

A test probe for a surface mounted leadless chip carrier is disclosed. The probe includes specially designed connector pins which allow size reductions in the probe. A thermoplastic housing provides spring action to ensure good mechanical and electrical contact between the pins and the contact strips of a leadless chip carrier. Other features include flexible wires molded into the housing and two different types of pins alternately placed in the housing. These features allow fabrication of a smaller and simpler test probe. 1 fig.

Meyer, K.L.; Topolewski, J.

1987-10-02T23:59:59.000Z

173

Substation Grounding Grids  

Science Conference Proceedings (OSTI)

This report is an account of research performed by the Electric Power Research Institute (EPRI) in 2011 on the subject of degradation of buried grounding grids in electric power substations. Substation ground grids are usually made of copper conductors, which are placed below grade and are joined together and to the above-grade structures with various types of connectors. While above-grade connections are visible and may be inspected, below-grade connections are not visible or readily accessible for insp...

2011-12-22T23:59:59.000Z

174

EPRI Substation Grounding Project  

Science Conference Proceedings (OSTI)

The Electric Power Research Institute (EPRI) has been conducting research in the area of substation grounding and fault current management for several decades. This research has resulted in a large number of reports and other products. To help users locate the results of EPRI’s research in substation grounding and fault current management, an annual update is prepared containing brief descriptions of the products.ObjectiveThe objective of this report is ...

2012-09-06T23:59:59.000Z

175

Substation grounding programs  

SciTech Connect

This document is a users manual and applications guide for the software package SGA. This package comprises four computer programs, namely SOMIP, SMECC, SGSYS, and TGRND. The first three programs are analysis models which are to be used in the design process of substation grounding systems. The fourth program, TGRND, is an analysis program for determining the transient response of a grounding system. This report, Volume 2, is a users manual and an installation and validation manual for the computer program SMECC (Substation Maximum Earth Current Computation Program). This program analyzes the electric current distribution among grounded structures inside and outside a substation for different fault conditions. The fault conditions are automatically selected by the program, or they may be specified by the user, or both. The fault condition resulting in maximum substation earth current is identified and reported. Data requirements for this program are: ground impedance, transformer data, transmission line data, transmission line grounding impedances, etc. The program provides four types of standard outputs: (1) a report of voltages and current flow in the unfaulted system, (2) a brief report of the maximum ground potential rise (worst fault condition), (3) a summary report of all fault conditions which have been analyzed by the program, and (4) a detailed report of voltages and current flow for a selected set of fault conditions.

Meliopoulos, A.P.S. (Georgia Inst. of Tech., Atlanta, GA (United States). Electric Power Lab.)

1992-05-01T23:59:59.000Z

176

Technical Review Report for the Mound 1KW Package Safety Analysis Report for Packaging Addendum No. 1, through Revision b  

SciTech Connect

This Technical Review Report (TRR) documents the review, performed by the Lawrence Livermore National Laboratory (LLNL) staff, at the request of the U.S. Department of Energy (DOE), on the 'Mound 1KW Package Safety Analysis Report for Packaging, Addendum No. 1, Revision b', dated May 2007 (Addendum 1). The Mound 1KW Package is certified by DOE Certificate of Compliance (CoC) number USA/9516/B(U)F-85 for the transportation of Type B quantities of plutonium heat source material. The safety analysis of the package is documented in the 'Safety Analysis Report for Packaging (SARP) for the Mound 1KW Package' (i.e., the Mound 1KW SARP, or the SARP). Addendum 1 incorporates a new fueled capsule assembly payload. The following changes have been made to add this payload: (1) The primary containment vessel (PCV) will be of the same design, but will increase in height to 11.16 in.; (2) A new graphite support block will be added to support up to three fueled capsule assemblies per package; (3) The cutting groove height on the secondary containment vessel (SCV) will be heightened to accommodate the taller PCV; and (4) A 3.38 in. high graphite filler block will be placed on top of the PCV. All other packaging features, as described in the Mound 1KW SARP [3], remain unchanged. This report documents the LLNL review of Addendum 1[1]. The specific review for each SARP Chapter is documented herein.

DiSabatino, A; West, M; Hafner, R; Russell, E

2007-10-04T23:59:59.000Z

177

Guide for Transmission Line Grounding  

Science Conference Proceedings (OSTI)

Electrical utilities have a duty to provide effective grounding for managing steady-state and fault currents, whether near a large generating station or at a remote distribution pole ground. For transmission lines, this imperative is usually met with investment in overhead ground wires and grounding electrodes. Effective grounding at each tower improves reliability8212by providing low path impedance to lightning strokes8212and contributes to safety. However, the fundamental physical parameters in ground ...

2007-12-20T23:59:59.000Z

178

NedPower Mount Storm Wind Farm | Open Energy Information  

Open Energy Info (EERE)

Wind Farm Wind Farm Jump to: navigation, search Name NedPower Mount Storm Wind Farm Facility NedPower Mount Storm Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner Shell Wind Energy/Dominion Energy Developer NedPower/Shell Wind Energy/Dominion Energy Energy Purchaser Dominion Energy Location Grant County WV Coordinates 39.251507°, -79.178989° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":39.251507,"lon":-79.178989,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

179

Development and Demonstration of a New Generation High Efficiency 10kW Stationary Fuel Cell System  

SciTech Connect

The overall project objective is to develop and demonstrate a polymer electrolyte membrane fuel cell combined heat and power (PEMFC CHP) system that provides the foundation for commercial, mass produced units which achieve over 40% electrical efficiency (fuel to electric conversion) from 50-100% load, greater than 70% overall efficiency (fuel to electric energy + usable waste heat energy conversion), have the potential to achieve 40,000 hours durability on all major process components, and can be produced in high volumes at under $400/kW (revised to $750/kW per 2011 DOE estimates) capital cost.

Howell, Thomas Russell

2013-04-30T23:59:59.000Z

180

Substation grounding programs  

SciTech Connect

This document is a users manual and applications guide for the software package SGA. This package comprises four computer programs, namely SOMIP, SMECC, SGSYS, and TGRND. The first three programs are analysis models which are to be used in the design process of substation grounding systems. The fourth program, TGRND, is an analysis program for determining the transient response of a grounding system. This report, Volume 5, is an applications guide of the three computer programs. SOMIP, SMECC, and SGSYS, for the purpose of designing a safe substation grounding system. The applications guide utilizes four example substation grounding systems for the purpose of illustrating the application of the programs, SOMIP, SMECC, and SGSYS. The examples are based on data provided by four contributing utilities, namely, Houston Lighting and Power Company, Southern Company Services, Puget Sound Power and Light Company, and Arizona Public Service Company. For the purpose of illustrating specific capabilities of the computer programs, the data have been modified. As a result, the final designs of the four systems do not necessarily represent actual grounding system designs by these utilities. The example system 1 is a 138 kV/35 kV distribution substation. The example system 2 is a medium size 230 kV/115 kV transmission substation. The third example system is a generation substation while the last is a large 525 kV/345 kV/230 kV transmission substation. The four examples cover most of the practical problems that a user may encounter in the design of substation grounding systems.

Meliopoulos, A.P.S. (Georgia Inst. of Tech., Atlanta, GA (United States). Electric Power Lab.)

1992-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "kw ground mounted" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

150,000 r/min-1.5 kW PM Efficiency Improvement by Means of Permeance Coefficient Optimization of 150,000-r/min, 1.5-kW PM Motor  

E-Print Network (OSTI)

University of Technology) This paper describes an ultra high-speed permanent-magnet synchronous motor design. Configuration of ultra high-speed PM motor. Core Coil (Winding) Air Permanent Magnet Shaft Stator Air 2 FEM Optimization of 150,000-r/min, 1.5-kW PM Motor Masaru Kano, Student Member, Toshihiko Noguchi, Member (Nagaoka

Fujimoto, Hiroshi

182

Substation Ground Grid Impedance Measurement  

Science Conference Proceedings (OSTI)

Because safety impacts all segments of the electric power industry, the integrity and conformance to standards of substation grounding systems is of paramount importance. This report summarizes field demonstrations of commercially available meters for performance evaluation of large grounding systems, including the EPRI Ground Grid Evaluator (commercially known as the Smart Ground Multimeter or SGM).

2007-12-13T23:59:59.000Z

183

Laboratory Performance Testing of Residential Window Mounted Air Conditioners  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Laboratory Performance Testing of Residential Window Mounted Air Conditioners Jon Winkler Chuck Booten Dane Christensen Jeff Tomerlin April 29, 2012 NREL is a national laboratory of the U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, operated by the Alliance for Sustainable Energy, LLC. Why should we care? * Window AC unit sales dominate US market o 7.5 million units sold in 2011 - 36% more than ducted systems - Approx. 30% of installed capacity o Inexpensive relative to central units o Easy installation o Attractive for retrofits * Need accurate models in whole-building tools o Costs/savings relative to other solutions can be quantified o Spot cooling can reduce energy use, but when, where and by

184

City of Mount Dora, Florida (Utility Company) | Open Energy Information  

Open Energy Info (EERE)

Dora, Florida (Utility Company) Dora, Florida (Utility Company) Jump to: navigation, search Name City of Mount Dora Place Florida Utility Id 13033 Utility Location Yes Ownership M NERC Location FRCC NERC FRCC Yes Activity Distribution Yes References EIA Form EIA-861 Final Data File for 2010 - File1_a[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. Utility Rate Schedules Grid-background.png General Service Commercial Demand Commercial General Service Non-Demand Single Phase Commercial General Service Non-Demand Three Phase Commercial Private Area Lighting 100 W HPS Lighting Public Street and Highway Lighting 100 W HPS Lighting Public Street and Highway Lighting 150 W HPS Lighting Public Street and Highway Lighting 175 W MV Lighting

185

Regenerative braking device with rotationally mounted energy storage means  

DOE Patents (OSTI)

A regenerative braking device for an automotive vehicle includes an energy storage assembly (12) having a plurality of rubber rollers (26, 28) mounted for rotation between an input shaft (30) and an output shaft (32), clutches (50, 56) and brakes (52, 58) associated with each shaft, and a continuously variable transmission (22) connectable to a vehicle drivetrain and to the input and output shafts by the respective clutches. In a second embodiment the clutches and brakes are dispensed with and the variable ratio transmission is connected directly across the input and output shafts. In both embodiments the rubber rollers are torsionally stressed to accumulate energy from the vehicle when the input shaft rotates faster or relative to the output shaft and are torsionally relaxed to deliver energy to the vehicle when the output shaft rotates faster or relative to the input shaft.

Hoppie, Lyle O. (Birmingham, MI)

1982-03-16T23:59:59.000Z

186

Wind loading on tracking and field-mounted solar collectors  

SciTech Connect

Current design and testing procedures for wind loading are discussed. The test results corresponding to numerous wind tests on heliostats, parabolic troughs, parabolic dishes, and field mounted photovoltaic arrays are discussed and the applicability of the findings across the various technologies is assessed. One of the most significant consistencies in the data from all of the technologies is the apparent benefit provided by fences and field shielding. Taken in toto, these data show that load reductions of three, or possibly more, seem feasible, though a more thorough understanding of the phenomena involved must be attained before this benefit can be realized. It is recommended that the required understanding be developed to take advantage of this benefit and that field tests be conducted to correlate with both analyses and tests.

Murphy, L.M.

1980-12-01T23:59:59.000Z

187

Frequency-Domain Synthesis Of The Fatigue Load Spectrum For The Nps 100-Kw Wind Turbine  

E-Print Network (OSTI)

* The LIFE2 code is a fatigue/fracture mechanics code that is specialized to the analysis of wind turbine components. Two frequency-domain stress spectra techniques contained in this code are used to analyze the measured frequency loads spectra from the Northern Power Systems 100-kW turbine. Results of the two techniques are compared to cycle counts obtained directly from time series data. These results provide the wind turbine designer with two techniques for determining the cycle-counts from frequency data and illustrate the accuracy that the designer can expect from various cycle-counting techniques. INTRODUCTION The LIFE2 code is a fatigue/fracture mechanics code that is specialized to the analysis of wind turbine components. 1 This code permits the analysis of both time series 2 and frequency domain data. 3 In the case of the former, a "rainflow counting" algorithm is used to convert time series data into a cycle count matrix suitable for fatigue analysis. For the latter,...

Herbert J. Sutherland; Richard M. Osgood

1992-01-01T23:59:59.000Z

188

Design of a 3 kW wind turbine generator with thin airfoil blades  

SciTech Connect

Three blades of a 3 kW prototype wind turbine generator were designed with thin airfoil and a tip speed ratio of 3. The wind turbine has been controlled via two control methods: the variable pitch angle and by regulation of the field current of the generator and examined under real wind conditions. The characteristics of the thin airfoil, called ''Seven arcs thin airfoil'' named so because the airfoil is composed of seven circular arcs, are analyzed with the airfoil design and analysis program XFOIL. The thin airfoil blade is designed and calculated by blade element and momentum theory. The performance characteristics of the machine such as rotational speed, generator output as well as stability for wind speed changes are described. In the case of average wind speeds of 10 m/s and a maximum of 19 m/s, the automatically controlled wind turbine ran safely through rough wind conditions and showed an average generator output of 1105 W and a power coefficient 0.14. (author)

Ameku, Kazumasa; Nagai, Baku M.; Roy, Jitendro Nath [Faculty of Mechanical Engineering, University of the Ryukyus, 1 Senbaru, Nishihara-cho, Okinawa 903-0213 (Japan)

2008-09-15T23:59:59.000Z

189

Test results from the 500 kW direct contact pilot plant at East Mesa  

DOE Green Energy (OSTI)

A 500 kW power plant utilizing direct contact heat exchange (DCHX) between the geothermal brine and the isobutane (IC/sub 4/) working fluid is being operated at the East Mesa test facility. The power plant incorporates a 40-inch-diameter direct-contactor approximately 35 feet tall. The purpose of the pilot plant is to determine the feasibility of large-scale direct-contact heat exchange and power plant operation with the DCHX. The binary cycle offers higher conversion factors (heat energy transformed to electrical energy) than the flashed steam approach for geothermal brines in the 300 to 400/sup 0/F range and preliminary results indicate the DCHX system may have higher performance than the conventional tube-and-shell binary approach. This performance advantage results from the absence of any fouling and the very close pinch temperatures achieved in the DCHX itself. The baseline performance tests for the plant were completed in January 1980. The results of these tests and follow-on testing are covered.

Nichols, K.E.; Olander, R.G.; Lobach, J.L.

1980-09-01T23:59:59.000Z

190

Characterization of Settler Tank, KW Container and KE Container Sludge Simulants  

Science Conference Proceedings (OSTI)

The Sludge Treatment Project (STP), managed by CH2M Hill Plateau Remediation Company (CHPRC) has specified base formulations for non-radioactive sludge simulants for use in the development and testing of equipment for sludge sampling, retrieval, transport, and processing. In general, the simulant formulations are based on the average or design-basis physical and chemical properties obtained by characterizing sludge samples. The simulants include surrogates for uranium metal, uranium oxides (agglomerates and fine particulate), and the predominant chemical phases (iron and aluminum hydroxides, sand). Specific surrogate components were selected to match the nominal particle-size distribution and particle-density data obtained from sludge sample analysis. Under contract to CHPRC, Pacific Northwest National Laboratory (PNNL) has performed physical and rheological characterization of simulants, and the results are reported here. Two base simulant types (dry) were prepared by STP staff at the Maintenance and Storage Facility and received by PNNL in February 2009: Settler Tank Simulant and KW Container Sludge Simulant. A third simulant, KE Container Sludge Simulant was received by PNNL in December 2010. The objectives of this simulant characterization effort were to provide baseline characterization data on simulants being used by STP for process development and equipment testing and provide a high-level comparison of the simulant characteristics to the targets used to formulate the simulants.

Burns, Carolyn A.; Luna, Maria L.; Schmidt, Andrew J.

2011-04-01T23:59:59.000Z

191

Development of a 75-kW heat-pipe receiver for solar heat-engines  

DOE Green Energy (OSTI)

A program is now underway to develop commercial power conversion systems that use parabolic dish mirrors in conjunction with Stirling engines to convert solar energy to electric power. In early prototypes, the solar concentrator focused light directly on the heater tubes of the Stirling engine. Liquid-metal heat-pipes are now being developed to transfer energy from the focus of the solar concentrator to the heater tubes of the engine. The dome-shaped heat-pipe receivers are approximately one-half meters in diameter and up to 77-kW of concentrated solar energy is delivered to the absorber surface. Over the past several years, Sandia National Laboratories, through the sponsorship of the Department of Energy, has conducted a major program to explore receiver designs and identify suitable wick materials. A high-flux bench-scale system has been developed to test candidate wick designs, and full-scale systems have been tested on an 11-meter test-bed solar concentrator. Procedures have also been developed in this program to measure the properties of wick materials, and an extensive data-base on wick materials for high temperature heat pipes has been developed. This paper provides an overview of the receiver development program and results from some of the many heat-pipe tests.

Adkins, D.R.; Andraka, C.E.; Moss, T.A.

1995-05-01T23:59:59.000Z

192

FLOATING PRESSURE CONVERSION AND EQUIPMENT UPGRADES OF TWO 3.5KW, 20K, HELIUM REFRIGERATORS  

SciTech Connect

Two helium refrigerators, each rated for 3.5 KW at 20 K, are used at NASA's Johnson Space Center (JSC) in Building No. 32 to provide cryogenic-pumping within two large thermal-vacuum chambers. These refrigerators were originally commissioned in 1996. New changes to the controls of these refrigerators were recently completed. This paper describes some of the control issues that necessitated the controls change-over. It will describe the modifications and the new process control which allows the refrigerators to take advantage of the Ganni Cycle “floating pressure” control technology. The controls philosophy change-over to the floating pressure control technology was the first application on a helium gas refrigeration system. Previous implementations of the floating pressure technology have been on 4 K liquefaction and refrigeration systems, which have stored liquid helium volumes that have level indications used for varying the pressure levels (charge) in the system for capacity modulation. The upgrades have greatly improved the performance, stability, and efficiency of these two refrigerators. The upgrades have also given the operators more information and details about the operational status of the main components (compressors, expanders etc.) of the refrigerators at all operating conditions (i.e. at various loads in the vacuum chambers). The performance data of the two systems, pre and post upgrading are presented.

J. Homan, V. Ganni, A. Sidi-Yekhlef, J. Creel, R. Norton, R. Linza, G. Vargas, J. Lauterbach, J. Urbin, D. Howe

2010-04-01T23:59:59.000Z

193

Improved Smart Ground Multimeter  

Science Conference Proceedings (OSTI)

The Smart Ground Multimeter (SGM) underwent three major redesigns since its original development in the early 1980s. This report describes the latest redesign and provides useful tips on the assessment of measured data quality and on resolving measurement problems in the field.

2006-12-18T23:59:59.000Z

194

Substation grounding programs  

SciTech Connect

The five volume report comprises the user manual, installation, and validation manual and an applications guide for the SGA (Substation Grounding Analysis) software package. SGA consists of four computer programs: (1) SOMIP, (2) SMECC, (3) SGSYS, and (4) TGRND. The first three programs provide a comprehensive analysis tool for the design of substation grounding systems to meet safety standards. The fourth program, TGRND, provides a state of the art analysis tool for computing transient ground potential rise and ground system impedance. This part of the report, Volume 1, is a users manual and an installation and validation manual for the computer program SOMIP (SOil Measurement Interpretation Program). This program computes the best estimate of the parameters of a two layer soil model from usual soil resistivity measurements. Four pin or three pin soil measurements can be accommodated. In addition, it provides error bounds on the soil parameters for a given confidence level. The users manual describes data requirements and data preparation procedures. The installation and validation manual describes the computer files which make up the program SOMIP and provides two test cases for validation purposes. 4 refs.

Meliopoulos, A.P.S. (Georgia Inst. of Tech., Atlanta, GA (United States). School of Electrical Engineering)

1992-05-01T23:59:59.000Z

195

Wind Turbine Generator System Power Performance Test Report for the Gaia-Wind 11-kW Wind Turbine  

DOE Green Energy (OSTI)

This test was conducted as part of the U.S. Department of Energy's (DOE) Independent Testing project. It is a power performance test that the National Renewable Energy Laboratory (NREL) conducted on the Gaia-Wind 11-kW small wind turbine.

Huskey, A.; Bowen, A.; Jager, D.

2009-12-01T23:59:59.000Z

196

160,000-r/min, 2.7-kW Electric Drive of Supercharger for Automobiles  

E-Print Network (OSTI)

,000-r/min, 2.7-kW permanent-magnet synchronous motor drive is discussed and its experimental test-supercharger; centrifugal compressor; ultra high- speed permanent magnet synchronous motor; pseudo-current- source inverter, Nagasaki, Nagasaki 851-0392, Japan Abstract--This paper describes an ultra high-speed permanent- magnet

Fujimoto, Hiroshi

197

220,000-r/min, 2-kW Permanent Magnet Motor Drive for Turbocharger Toshihiko Noguchi, Yosuke Takata *  

E-Print Network (OSTI)

220,000-r/min, 2-kW Permanent Magnet Motor Drive for Turbocharger Toshihiko Noguchi, Yosuke Takata-speed permanent-magnet synchronous motor drive, which is embedded in a turbocharger of an internal permanent magnet. Also, it is indispensable to reduce the motor inductance less than 10 (µH) because dc bus

Fujimoto, Hiroshi

198

Assessment of a 200-kW Fuel Cell at the U.S. Army Natick Research Center  

Science Conference Proceedings (OSTI)

The utility industry is showing renewed interest in distributed generation, with a particular interest in fuel cells. This on-going project will provide long-term data on performance and operating characteristics of an ONSI 200-kW phosphoric acid fuel cell at the U.S. Army RD&E Center in Natick, Massachusetts.

1997-10-04T23:59:59.000Z

199

1?10 kW Stationary Combined Heat and Power Systems Status and Technical Potential: Independent Review  

DOE Green Energy (OSTI)

This independent review examines the status and technical potential of 1-10 kW stationary combined heat and power fuel cell systems and analyzes the achievability of the DOE cost, efficiency, and durability targets for 2012, 2015, and 2020.

Maru, H. C.; Singhal, S. C.; Stone, C.; Wheeler, D.

2010-11-01T23:59:59.000Z

200

Wind Turbine Generator System Power Performance Test Report for the Gaia-Wind 11-kW Wind Turbine  

SciTech Connect

This test was conducted as part of the U.S. Department of Energy's (DOE) Independent Testing project. It is a power performance test that the National Renewable Energy Laboratory (NREL) conducted on the Gaia-Wind 11-kW small wind turbine.

Huskey, A.; Bowen, A.; Jager, D.

2009-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "kw ground mounted" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Modeling and Implementation of a 1 kW, Air Cooled HTPEM Fuel Cell in a Hybrid Electrical Vehicle  

E-Print Network (OSTI)

Modeling and Implementation of a 1 kW, Air Cooled HTPEM Fuel Cell in a Hybrid Electrical Vehicle engine vehicles (1). Hybrid systems of many kinds, combining a primary energy source having a high energy://www.ecsdl.org/terms_use.jsp #12;article, a model of a hybrid vehicle, including a HTPEM with lead acid batteries, is de- veloped

Nielsen, Mads Pagh

202

Performance Comparison of a BIPV Roofing Tile System in Two Mounting Configurations (Poster)  

DOE Green Energy (OSTI)

This work examined the thermal and power characteristics of a building-integrated photovoltaic (BIPV) roofing system using two installation techniques, counter-batten and direct-mount.

Muller, M.; Rodriquez, J.; Marion, B.

2009-06-01T23:59:59.000Z

203

Performance Comparison of a BIPV Roofing Tile System in Two Mounting Configurations: Preprint  

DOE Green Energy (OSTI)

This work examined the thermal and power characteristics of a building-integrated photovoltaic (BIPV) roofing system using two installation techniques, counter-batten and direct-mount.

Muller, M. T.; Rodrigeuz, J.; Marion, B.

2009-06-01T23:59:59.000Z

204

Status of the Advanced Stirling Conversion System Project for 25 kW dish Stirling applications  

DOE Green Energy (OSTI)

Under the Department of Energy's (DOE) Solar Thermal Technology Program, Sandia National Laboratories is evaluating heat engines for terrestrial Solar Heat Receivers. The Stirling engine has been identified by Sandia as one of the most promising heat engines for terrestrial applications. The Stirling engine also has the potential to meet DOE's performance and cost goals. The NASA Lewis Research Center is conducting technology development for Stirling convertors directed toward a dynamic power source for space applications. Space power requirements include high reliability with very long life, low vibration and high system efficiency. The free-piston Stirling engine has the potential for future high power space conversion systems, either nuclear or solar powered. Although both applications appear to be quite different, their requirements complement each other. NASA Lewis is providing management of the Advanced Stirling Conversion System (ASCS) Project through an Interagency Agreement (IAA) with the DOE. Parallel contracts continue with both Cummins Engine Company (CEC), Columbus, Indiana, and Stirling Technology Company (STC), Richland, Washington for the designs of an ASCS. Each system'' design features a solar receiver/liquid metal heat transport system, and a free-piston Stirling convertor with a means to provide nominally 25 kW of electric power to a utility grid while meeting DOE's performance and long-term'' cost goals. The Cummins free- piston Stirling convertor incorporates a linear alternator to directly provide the electrical output, while the STC design generates electrical power indirectly through a hydraulic pump/motor coupled to an induction generator. Both the Cummins and STC ASCS designs will use technology which can reasonably be expected to be available in the early 1990's. 17 refs., 7 figs., 3 tabs.

Shaltens, R.K.; Schreiber, J.G.

1991-01-01T23:59:59.000Z

205

Ground State Entanglement Energetics  

E-Print Network (OSTI)

We consider the ground state of simple quantum systems coupled to an environment. In general the system is entangled with its environment. As a consequence, even at zero temperature, the energy of the system is not sharp: a projective measurement can find the system in an excited state. We show that energy fluctuation measurements at zero temperature provide entanglement information. For two-state systems which exhibit a persistent current in the ground state, energy fluctuations and persistent current fluctuations are closely related. The harmonic oscillator serves to illustrate energy fluctuations in a system with an infinite number of states. In addition to the energy distribution we discuss the energy-energy time-correlation function in the zero-temperature limit.

M. Buttiker; A. N. Jordan

2005-01-04T23:59:59.000Z

206

CEUS Ground Motion Project  

Science Conference Proceedings (OSTI)

Three utilities are currently pursuing early site permits (ESPs) for possible siting of new nuclear power plant facilities in the central and eastern United States (CEUS). The geological, seismological, and engineering characteristics of a site and its environs must be investigated in sufficient scope and detail. These investigations are needed to adequately evaluate a proposed site and to provide sufficient information for estimating the site's safe shutdown earthquake (SSE) ground motion. Nuclear Regul...

2003-12-02T23:59:59.000Z

207

Ground Squirrels and Gophers  

NLE Websites -- All DOE Office Websites (Extended Search)

Squirrels and Gophers Squirrels and Gophers Nature Bulletin No. 224-A April 2, 1966 Forest Preserve District of Cook County Seymour Simon, President Roland F. Eisenbeis, Supt. of Conservation GROUND SQUIRRELS AND GOPHERS On sunny summer days, a dusty-colored animal with yellowish and brown stripes, about the size of a small rat, often may be noticed creeping through the grass of prairies, pastures, golf courses or lawns. Watch him. He pauses every few feet to sit up, look and listen for a moment. Nervous and timid, he crouches low at every distant sound or passing shadow. Startle him and he scurries away, and then may suddenly halt and freeze, bolt upright, as stiff and straight as a stake driven in the ground. If approached, he gives a loud shrill trilling whistle and, with a flip of his tail, pops out of sight. Watch that spot closely and, in less than a minute, a snaky head appears. Be quiet. He has many enemies above ground and he also has a lot of curiosity. Presently he sits up upon his haunches again.

208

Performance Evaluation of a 4.5 kW (1.3 Refrigeration Tons) Air-Cooled Lithium Bromide/Water Solar Powered (Hot-Water-Fired) Absorption Unit  

Science Conference Proceedings (OSTI)

During the summer months, air-conditioning (cooling) is the single largest use of electricity in both residential and commercial buildings with the major impact on peak electric demand. Improved air-conditioning technology has by far the greatest potential impact on the electric industry compared to any other technology that uses electricity. Thermally activated absorption air-conditioning (absorption chillers) can provide overall peak load reduction and electric grid relief for summer peak demand. This innovative absorption technology is based on integrated rotating heat exchangers to enhance heat and mass transfer resulting in a potential reduction of size, cost, and weight of the "next generation" absorption units. Rotartica Absorption Chiller (RAC) is a 4.5 kW (1.3 refrigeration tons or RT) air-cooled lithium bromide (LiBr)/water unit powered by hot water generated using the solar energy and/or waste heat. Typically LiBr/water absorption chillers are water-cooled units which use a cooling tower to reject heat. Cooling towers require a large amount of space, increase start-up and maintenance costs. However, RAC is an air-cooled absorption chiller (no cooling tower). The purpose of this evaluation is to verify RAC performance by comparing the Coefficient of Performance (COP or ratio of cooling capacity to energy input) and the cooling capacity results with those of the manufacturer. The performance of the RAC was tested at Oak Ridge National Laboratory (ORNL) in a controlled environment at various hot and chilled water flow rates, air handler flow rates, and ambient temperatures. Temperature probes, mass flow meters, rotational speed measuring device, pressure transducers, and a web camera mounted inside the unit were used to monitor the RAC via a web control-based data acquisition system using Automated Logic Controller (ALC). Results showed a COP and cooling capacity of approximately 0.58 and 3.7 kW respectively at 35 C (95 F) design condition for ambient temperature with 40 C (104 F) cooling water temperature. This is in close agreement with the manufacturer data of 0.60 for COP and 3.9 kW for cooling capacity. This study resulted in a complete performance map of RAC which will be used to evaluate the potential benefits of rotating heat exchangers in making the "next-generation" absorption chillers more compact and cost effective without any significant degradation in the performance. In addition, the feasibility of using rotating heat exchangers in other applications will be evaluated.

Zaltash, Abdolreza [ORNL; Petrov, Andrei Y [ORNL; Linkous, Randall Lee [ORNL; Vineyard, Edward Allan [ORNL

2007-01-01T23:59:59.000Z

209

Evaluating requirements for gaze-based interaction in a see-through head mounted display  

Science Conference Proceedings (OSTI)

This study suggests an approach to the evaluation of gaze-based interaction with information displayed on a see-through HMD. For these purposes, a mock-up system consisting of a head-mounted eye tracker and a see-through HMD was developed. In a series ... Keywords: eye tracking, gaze control, head-mounted displays, human computer interaction

Sven-Thomas Graupner; Michael Heubner; Sebastian Pannasch; Boris M. Velichkovsky

2008-03-01T23:59:59.000Z

210

A 200 000 rpm, 2 kW Slotless Permanent Magnet Pierre-Daniel Pfister, Student Member IEEE and Yves Perriard, Senior Member IEEE  

E-Print Network (OSTI)

A 200 000 rpm, 2 kW Slotless Permanent Magnet Motor Pierre-Daniel Pfister, Student Member IEEE high speed (200 krpm, 2 kW) slotless permanent magnet motor, using an analytical model that reached 200 krpm. Index Terms--Very high speed, Slotless permanent magnet motor, Multiphysics analytical

Psaltis, Demetri

211

NETL F 451.1-1/1 Categorical Exclusion (CX) Designation Form  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Carolina Green Business Fund - Vestal Farms The project will install a ground mounted biogas-to-energy system at the existing Vestal Farms hog farm. includes: 100 kW internal...

212

NETL F 451.1-1/1 Categorical Exclusion (CX) Designation Form  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Carolina Green Business Fund - Storms Farms The project will install a ground mounted biogas-to-energy system at existing Storms Farms hog farm. includes: two 100 kW internal...

213

NETL F 451.1-1/1 Categorical Exclusion (CX) Designation Form  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Carolina Green Business Fund - Butler Farms The project will install a ground mounted biogas-to-energy system at the existing Butler Farm hog farm. includes:100 kw internal...

214

NETL F 451.1-1/1 Categorical Exclusion (CX) Designation Form  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

MD 21811 Grants to Promote Mid-size Renewables at Private and Government Buildings - Ocean Landings Installation of 70 kW ground mounted solar array PV system with inverters. 05...

215

Supporting Solar Power in Renewables Portfolio Standards: Experience from the United States  

E-Print Network (OSTI)

large (>500 kW) rooftop systems and “solar gardens” owned bySolar PV Distributed Generation Program: Duke Energy plans to install 10 MW of ground-mounted and rooftop

Wiser, Ryan

2010-01-01T23:59:59.000Z

216

U.S. DEPARTMENT OF ENERGY - NETL CATEGORICAL EXCLUSION (CX) DESIGNATIO...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

East Haddam, CT Solar PV Program - Ballek Garden Center Installation of 50.36 kW (AC) solar PV system. The ground mounted system will be installed at the existing facility to...

217

U.S. DEPARTMENT OF ENERGY - NETL CATEGORICAL EXCLUSION (CX) DESIGNATIO...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Mansfield, CT Solar PV Program - Windham Water Works Installation of 80.08 kW (AC) solar PV system at the existing Windham Water Works location. The ground mounted system will...

218

U.S. DEPARTMENT OF ENERGY - NETL CATEGORICAL EXCLUSION (CX) DESIGNATIO...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Sterling, CT Solar PV Program - Molodich Farm Installation of 115.92 kW (DC) ground mounted solar photovoltaic (PV) system and one buried conduit. Teresa Jones Digitally signed by...

219

Model As-of Right Zoning Ordinance or Bylaw: Allowing Use of Large-Scale Solar Energy Facilities  

Energy.gov (U.S. Department of Energy (DOE))

Note: This model ordinance was designed to provide guidance to local governments seeking to develop siting rules for large-scale, ground-mounted solar (250 kW and above). While it was developed as...

220

Beyond kWh and kW demand: Understanding the new real-time electric power  

NLE Websites -- All DOE Office Websites (Extended Search)

Beyond kWh and kW demand: Understanding the new real-time electric power Beyond kWh and kW demand: Understanding the new real-time electric power measurement system in LBNL Building 90 Speaker(s): Alex McEachern Date: January 14, 2010 - 12:00pm Location: 90-3122 In the Summer of 2009, LBNL researchers installed end-use sub-metering equipment and associated Energy Information System (EIS) tools to characterize energy use and comfort in Building 90. Seven of 40 key electric loads were measured using advanced meters that make sophisticated real-time measurements of dozens of power flow parameters, power disturbances, and harmonics. The talk will review some electrical engineering fundamentals, how use and interpret data measured in building 90 in real-time. The real-time data available includes power, volt-amps, VAR's, unbalance voltage and current, voltage and current distortion,

Note: This page contains sample records for the topic "kw ground mounted" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

1Â…10 kW Stationary Combined Heat and Power Systems Status and Technical Potential: Independent Review  

NLE Websites -- All DOE Office Websites (Extended Search)

1-10 kW Stationary Combined Heat 1-10 kW Stationary Combined Heat and Power Systems Status and Technical Potential National Renewable Energy Laboratory 1617 Cole Boulevard * Golden, Colorado 80401 303-275-3000 * www.nrel.gov NREL is a national laboratory of the U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, operated by the Alliance for Sustainable Energy, LLC. Contract No. DE-AC36-08GO28308 Independent Review Published for the U.S. Department of Energy Hydrogen and Fuel Cells Program NREL/BK-6A10-48265 November 2010 NOTICE This report was prepared as an account of work sponsored by an agency of the United States government. Neither the United States government nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or

222

Assessment of a Transportable 200-kW Fuel Cell in Rural Distributed Generation Applications: Final Report: Georgia, Colorado, Alaska  

Science Conference Proceedings (OSTI)

Distributed generation is particularly attractive to electric cooperatives in rural areas because of their low customer densities and the rapid load growth that often occurs at the end of long radial distribution lines. EPRI and the National Rural Electric Cooperative Association (NRECA) Cooperative Research Network cosponsored this project to demonstrate the use of transportable 200-kW phosphoric acid fuel cell power plants in rural distributed generation applications. This final report details the proj...

2002-07-19T23:59:59.000Z

223

Wind Turbinie Generator System Power Performance Test Report for the Mariah Windspire 1-kW Wind Turbine  

DOE Green Energy (OSTI)

This report summarizes the results of a power performance test that NREL conducted on the Mariah Windspire 1-kW wind turbine. During this test, two configurations were tested on the same turbine. In the first configuration, the turbine inverter was optimized for power production. In the second configuration, the turbine inverter was set for normal power production. In both configurations, the inverter experienced failures and the tests were not finished.

Huskey, A.; Bowen, A.; Jager, D.

2009-12-01T23:59:59.000Z

224

Development of a low-cost, light-weight, efficient, 1. 5 kW inverter. Final report  

SciTech Connect

The effective use of low-voltage dc power sources, such as fuel cells and batteries, requires efficient power conversion equipment to provide ac voltages. The development of a silent, light-weight inverter is discussed in this paper. The inverter is capable of delivering 1.5 kW into a 0.8-1.0 power factor load at 120 or 240 Vac and at 60 or 400 Hz. (GRA)

Suelzle, L.R.; Suelzle, J.S.

1975-09-01T23:59:59.000Z

225

Test and Evaluation of a 6 kW Microgenerator Aisin G-60 Phase-1 Field Demonstration  

Science Conference Proceedings (OSTI)

This case study documents the demonstration experiences and lessons learned from a 6 kW microgenerator in a field demonstration operating on natural gas at an end-user site. The microgenerator uses a novel internal combustion engine and generator packaged for combined heat and power applications. The test and evaluation case study is one of several distributed generation project case studies under research by EPRI's Distributed Energy Resources Program. This case study was designed to help utilities and ...

2004-12-27T23:59:59.000Z

226

Ground-source heat pump case studies and utility programs  

DOE Green Energy (OSTI)

Ground-source heat pump systems are one of the promising new energy technologies that has shown rapid increase in usage over the past ten years in the United States. These systems offer substantial benefits to consumers and utilities in energy (kWh) and demand (kW) savings. The purpose of this study was to determine what existing monitored data was available mainly from electric utilities on heat pump performance, energy savings and demand reduction for residential, school and commercial building applications. In order to verify the performance, information was collected for 253 case studies from mainly utilities throughout the United States. The case studies were compiled into a database. The database was organized into general information, system information, ground system information, system performance, and additional information. Information was developed on the status of demand-side management of ground-source heat pump programs for about 60 electric utility and rural electric cooperatives on marketing, incentive programs, barriers to market penetration, number units installed in service area, and benefits.

Lienau, P.J.; Boyd, T.L.; Rogers, R.L.

1995-04-01T23:59:59.000Z

227

Ground potential rise monitor  

SciTech Connect

A device and method for detecting ground potential rise (GPR) comprising positioning a first electrode and a second electrode at a distance from each other into the earth. The voltage of the first electrode and second electrode is attenuated by an attenuation factor creating an attenuated voltage. The true RMS voltage of the attenuated voltage is determined creating an attenuated true RMS voltage. The attenuated true RMS voltage is then multiplied by the attenuation factor creating a calculated true RMS voltage. If the calculated true RMS voltage is greater than a first predetermined voltage threshold, a first alarm is enabled at a local location. If user input is received at a remote location acknowledging the first alarm, a first alarm acknowledgment signal is transmitted. The first alarm acknowledgment signal is then received at which time the first alarm is disabled.

Allen, Zachery W. (Mandan, ND); Zevenbergen, Gary A. (Arvada, CO)

2012-04-03T23:59:59.000Z

228

Case History of Reapplication of a 2500 KW Steam Turbine/Gear Drive Generator  

E-Print Network (OSTI)

In today' s equipment market more and more projects are turning toward existing equipment to justify a project. New equipment's delivery time and/or capital cost can keep a good project "grounded". In the turbomachinery industry, a few companies have developed the expertise to identify candidates of existing machines that can be adopted for many new applications. These companies can inspect, modify, recondition and rerate the equipment as needed, which helps bring in a project within budget and on time. This paper is the history of such an application. The delivery schedule requirements and limited capital made the project feasible only through the technology of reapplying existing machines to a new service. The project involves a plant that extracts landfill gas and converts it to diesel fuel, naphtha and a high grade of wax. The plant requires a steam turbine generator set to produce electrical power for its base load operation. This paper covers the history of how the turbine, gear and generator were selected, along with the highlights of the engineering work required to insure the mechanical operation of the string of equipment.

Smith, S.

1991-06-01T23:59:59.000Z

229

Ground Water Management Regulations (Louisiana) | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Ground Water Management Regulations (Louisiana) Ground Water Management Regulations (Louisiana) Eligibility Agricultural Construction Developer Fuel Distributor Industrial...

230

A Structural Model Guide For Geothermal Exploration In Ancestral Mount Bao,  

Open Energy Info (EERE)

Model Guide For Geothermal Exploration In Ancestral Mount Bao, Model Guide For Geothermal Exploration In Ancestral Mount Bao, Leyte, Philippines Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: A Structural Model Guide For Geothermal Exploration In Ancestral Mount Bao, Leyte, Philippines Details Activities (0) Areas (0) Regions (0) Abstract: The Tongonan Geothermal Field is the largest producing geothermal field in the Philippines having an installed capacity of 700 MW. It hosts several major power plants that tap geothermal power from the northern flank of the eroded Ancestral Mount Bao (AMB) volcano in Leyte Island, Philippines. A structural model guide is presented to delineate exploration targets in other flanks of the 1200 km2 area of the AMB volcano. If applied, the model constrains the coverage of geothermal exploration to

231

Mount Princeton Hot Springs Pool & Spa Low Temperature Geothermal Facility  

Open Energy Info (EERE)

Mount Princeton Hot Springs Pool & Spa Low Temperature Geothermal Facility Mount Princeton Hot Springs Pool & Spa Low Temperature Geothermal Facility Facility Mount Princeton Hot Springs Sector Geothermal energy Type Pool and Spa Location Mount Princeton, Colorado Coordinates 38.749167°, -106.2425° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[]}

232

V-227: VMware Workstation and Player vmware-mount Command Flaw Lets Local  

NLE Websites -- All DOE Office Websites (Extended Search)

7: VMware Workstation and Player vmware-mount Command Flaw Lets 7: VMware Workstation and Player vmware-mount Command Flaw Lets Local Users Gain Root Privileges V-227: VMware Workstation and Player vmware-mount Command Flaw Lets Local Users Gain Root Privileges August 26, 2013 - 6:00am Addthis PROBLEM: A vulnerability was reported in VMware Workstation and Player on Debian-based systems PLATFORM: VMware Workstation 8.x, 9.x and Player 4.x, 5.x ABSTRACT: VMware Workstation and Player contain a vulnerability in the handling of the vmware-mount command REFERENCE LINKS: Security Tracker Alert ID 1028948 VMware Security Advisory VMSA-2013-0010 CVE-2013-1662 IMPACT ASSESSMENT: Medium DISCUSSION: A local malicious user may exploit this vulnerability to escalate their privileges to root on the host OS. The issue is present when Workstation or

233

A Prehistoric Lahar-Dammed Lake And Eruption Of Mount Pinatubo Described In  

Open Energy Info (EERE)

Prehistoric Lahar-Dammed Lake And Eruption Of Mount Pinatubo Described In Prehistoric Lahar-Dammed Lake And Eruption Of Mount Pinatubo Described In A Philippine Aborigine Legend Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: A Prehistoric Lahar-Dammed Lake And Eruption Of Mount Pinatubo Described In A Philippine Aborigine Legend Details Activities (0) Areas (0) Regions (0) Abstract: The prehistoric eruptions of Mount Pinatubo have followed a cycle: centuries of repose terminated by a caldera-forming eruption with large pyroclastic flows; a post-eruption aftermath of rain-triggered lahars in surrounding drainages and dome-building that fills the caldera; and then another long quiescent period. During and after the eruptions lahars descending along volcano channels may block tributaries from watersheds

234

The 1935–2003 Air Temperature Record from the Summit of Mount Washington, New Hampshire  

Science Conference Proceedings (OSTI)

Meteorological observations have been taken continuously at the summit of Mount Washington since 1932. Results of an analysis of the air temperature record over the 1935–2003 period show a statistically significant increase in mean temperature of ...

Andrea N. Grant; Alexander A. P. Pszenny; Emily V. Fischer

2005-11-01T23:59:59.000Z

235

Weather And Death On Mount Everest: An Analysis Of The Into Thin Air Storm  

Science Conference Proceedings (OSTI)

Scientific interest in Mount Everest has been largely focused on the physiology of hypoxia caused by the summit's low barometric pressure. Although weather is recognized as a significant risk for climbers on the mountain, it has not been ...

G. W. K. Moore; John L. Semple

2006-04-01T23:59:59.000Z

236

An Investigation of the Consistency of TAO–TRITON Buoy-Mounted Capacitance Rain Gauges  

Science Conference Proceedings (OSTI)

The common use of remotely located, buoy-mounted capacitance rain gauges in the tropical oceans for satellite rainfall verification studies provides motivation for an in situ gauge bias assessment. A comparison of the biases in rainfall catchment ...

Mark L. Morrissey; Howard J. Diamond; Michael J. McPhaden; H. Paul Freitag; J. Scott Greene

2012-06-01T23:59:59.000Z

237

Mount Kenya Global Atmosphere Watch Station (MKN): Installation and Meteorological Characterization  

Science Conference Proceedings (OSTI)

The meteorological conditions at the Mount Kenya (station identifier MKN) tropical Global Atmosphere Watch Programme station are described. Like other stations in mountainous terrain, the site experiences thermally induced wind systems that ...

Stephan Henne; Wolfgang Junkermann; Josiah M. Kariuki; John Aseyo; Jörg Klausen

2008-11-01T23:59:59.000Z

238

Effects of the Mount St. Helens Volcanic Cloud on Turbidity at Ann Arbor, Michigan  

Science Conference Proceedings (OSTI)

Measurements of turbidity were made at the University of Michigan irradiance and meteorological measurement facility just prior to, during and after the passage of the volcanic cloud from the 18 May 1980 eruption of Mount St. Helens. They were ...

Edward Ryznar; Michael R. Weber; Thomas S. Hallaron

1981-11-01T23:59:59.000Z

239

Effects of a Thermistor String Mounted between the Acoustic Beams of an Acoustic Doppler Current Profiler  

Science Conference Proceedings (OSTI)

A useful extension of upward-looking buoy-mounted acoustic Doppler current profilers (ADCPs), in particular for studying surface-mixed-layer dynamics from underneath, would be to combine them with a thermistor cable for obtaining simultaneous ...

Friedrich Schott

1988-02-01T23:59:59.000Z

240

An optical see-through head mounted display with addressable focal planes  

Science Conference Proceedings (OSTI)

Most existing stereoscopic head mounted displays (HMDs), presenting a pair of stereoscopic images at a fixed focal distance, lack the ability to correctly render the naturally coupled accommodation and convergence cues. Psychophysical studies have shown ...

Sheng Liu; Dewen Cheng; Hong Hua

2008-09-01T23:59:59.000Z

Note: This page contains sample records for the topic "kw ground mounted" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Comparison of Different Bin-mapping Methods for a Bottom-mounted Acoustic Profiler  

Science Conference Proceedings (OSTI)

Acouste Doppler current profilers (ADCPS) can measure profiles of velocity components and some other properties of bodies of water. If the profiler is firmly mounted, the profiles can be recorded without immediate coordinate transform. This gives ...

Kari Pulkkinen

1993-06-01T23:59:59.000Z

242

Assimilation of Ship-Mounted ADCP Data for Barotropic Tides: Application to the Ross Sea  

Science Conference Proceedings (OSTI)

The application of a generalized inverse approach for assimilating vessel-mounted acoustic Doppler current profiler (VM-ADCP) data into numerical solutions of barotropic tides is described. The derived estimates of tidal currents can be used to ...

S. Y. Erofeeva; Laurie Padman; Gary Egbert

2005-06-01T23:59:59.000Z

243

Evolution Of Hydrothermal Waters At Mount St Helens, Washington, Usa | Open  

Open Energy Info (EERE)

Evolution Of Hydrothermal Waters At Mount St Helens, Washington, Usa Evolution Of Hydrothermal Waters At Mount St Helens, Washington, Usa Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Evolution Of Hydrothermal Waters At Mount St Helens, Washington, Usa Details Activities (4) Areas (1) Regions (0) Abstract: Hydrothermal water samples at Mount St. Helens collected between 1985 and 1989 and in 1994 are used to identify water types and describe their evolution through time. Two types of low temperature hydrothermal systems are associated with the 1980 eruptions and were initiated soon after emplacement of shallow magma and pyroclastic flows. The Loowit hot spring system is located in the breach zone and is associated with the magma conduit and nearby avalanche deposits, whereas the Pumice Plain (PP)

244

Design and development of an automated pinning machine for the surface mount electronics industry  

E-Print Network (OSTI)

This thesis describes the development of a concept for a pinning process and the associated machinery to handle odd-form pins specific to a company in the surface mount electronics industry. The developed pinning machine ...

Cook, Daniel J., M. Eng. (Daniel James). Massachusetts Institute of Technology

2012-01-01T23:59:59.000Z

245

Wind Turbine Generator System Power Quality Test Report for the Gaia Wind 11-kW Wind Turbine  

DOE Green Energy (OSTI)

This report details the power quality test on the Gaia Wind 11-kW Wind Turbine as part of the U.S. Department of Energy's Independent Testing Project. In total five turbines are being tested as part of the project. Power quality testing is one of up to five test that may be performed on the turbines including power performance, safety and function, noise, and duration tests. The results of the testing provide manufacturers with reports that may be used for small wind turbine certification.

Curtis, A.; Gevorgian, V.

2011-07-01T23:59:59.000Z

246

Five kW Solid Oxide Fuel Cell Demonstration Project: Case Study: Exit Glacier Nature Center Acumentrics Demonstration  

Science Conference Proceedings (OSTI)

This case study documents the demonstration experiences and lessons learned from a 5 kW solid oxide fuel cell system operating on propane at the Kenai Fiords National Park at the Exit Glacier Visitor Center, Seward, Alaska. The case study is one of several fuel cell project case studies under research by EPRI's Distributed Energy Resources Program. This case study is designed to help utilities and other interested parties understand the early applications of fuel cell systems to help them in their resour...

2005-02-17T23:59:59.000Z

247

Mime: compact, low power 3D gesture sensing for interaction with head mounted displays  

Science Conference Proceedings (OSTI)

We present Mime, a compact, low-power 3D sensor for unencumbered free-form, single-handed gestural interaction with head-mounted displays (HMDs). Mime introduces a real-time signal processing framework that combines a novel three-pixel time-of-flight ... Keywords: 3d sensing, gesture sensing, glasses, hand tracking, head mounted displays, mobile, time-of- flight imaging

Andrea Colaço, Ahmed Kirmani, Hye Soo Yang, Nan-Wei Gong, Chris Schmandt, Vivek K. Goyal

2013-10-01T23:59:59.000Z

248

Advanced, High-Reliability, System-Integrated 500kW PV Inverter Development: Final Subcontract Report, 29 September 2005 - 31 May 2008  

DOE Green Energy (OSTI)

Xantrex Technology accomplished subcontract goals of reducing parts cost, weight, and size of its 500-kW inverter by 25% compared to state-of-the-art PV inverters, while extending reliability by 25%.

West, R.

2008-08-01T23:59:59.000Z

249

EPA Final Ground Water Rule  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Office of Nuclear Safety and Environment Office of Nuclear Safety and Environment Nuclear Safety and Environment Information Brief HS-20-IB-2007-02 (March 2007) EPA Final Ground Water Rule Safe Drinking Water Act: National Primary Drinking Water Regulations Ground Water Rule - 40 CFR Parts 9, 141 and 142 Final Rule: 71 FR 65574 Effective Date: January 8, 2007 1 RULE SYNOPSIS On November 8, 2006, the U.S. Environmental Protection Agency (EPA) published a final Ground Water Rule (GWR) to promote increased protection against microbial pathogens that may be present in public water systems (PWSs) that use ground water sources for their supply (these systems are known as ground water systems). This Rule establishes a risk-targeted approach

250

Scaling and Optimization of Magnetic Refrigeration for Commercial Building HVAC Systems Greater than 175 kW in Capacity  

Science Conference Proceedings (OSTI)

Heating, ventilation, air-conditioning and refrigeration (HVACR) account for approximately one- third of building energy consumption. Magnetic refrigeration presents an opportunity for significant energy savings and emissions reduction for serving the building heating, cooling, and refrigeration loads. In this paper, we have examined the magnet and MCE material requirements for scaling magnetic refrigeration systems for commercial building cooling applications. Scaling relationships governing the resources required for magnetic refrigeration systems have been developed. As system refrigeration capacity increases, the use of superconducting magnet systems becomes more applicable, and a comparison is presented of system requirements for permanent and superconducting (SC) magnetization systems. Included in this analysis is an investigation of the ability of superconducting magnet based systems to overcome the parasitic power penalty of the cryocooler used to keep SC windings at cryogenic temperatures. Scaling relationships were used to develop the initial specification for a SC magnet-based active magnetic regeneration (AMR) system. An optimized superconducting magnet was designed to support this system. In this analysis, we show that the SC magnet system consisting of two 0.38 m3 regenerators is capable of producing 285 kW of cooling power with a T of 28 K. A system COP of 4.02 including cryocooler and fan losses which illustrates that an SC magnet-based system can operate with efficiency comparable to traditional systems and deliver large cooling powers of 285.4 kW (81.2 Tons).

Abdelaziz, Omar [ORNL; West, David L [ORNL; Mallow, Anne M [ORNL

2012-01-01T23:59:59.000Z

251

Exergy and Energy analysis of a ground-source heat pump for domestic water heating under simulated occupancy conditions  

SciTech Connect

This paper presents detailed analysis of a water to water ground source heat pump (WW-GSHP) to provide all the hot water needs in a 345 m2 house located in DOE climate zone 4 (mixed-humid). The protocol for hot water use is based on the Building America Research Benchmark Definition (Hendron 2008; Hendron and Engebrecht 2010) which aims to capture the living habits of the average American household and its impact on energy consumption. The entire house was operated under simulated occupancy conditions. Detailed energy and exergy analysis provides a complete set of information on system efficiency and sources of irreversibility, the main cause of wasted energy. The WW-GSHP was sized at 5.275 kW (1.5-ton) for this house and supplied hot water to a 303 L (80 gal) water storage tank. The WW-GSHP shared the same ground loop with a 7.56 kW (2.1-ton) water to air ground source heat pump (WA-GSHP) which provided space conditioning needs to the entire house. Data, analyses, and measures of performance for the WW-GSHP in this paper complements the results of the WA-GSHP published in this journal (Ally, Munk et al. 2012). Understanding the performance of GSHPs is vital if the ground is to be used as a viable renewable energy resource.

Ally, Moonis Raza [ORNL; Munk, Jeffrey D [ORNL; Baxter, Van D [ORNL; Gehl, Anthony C [ORNL

2012-01-01T23:59:59.000Z

252

Alternative Materials for Ground Electrodes  

Science Conference Proceedings (OSTI)

Power utility companies struggle with issues resulting from copper theftespecially on transmission line support structures accessible to the public and fitted with copper grounding conductors. It is increasingly important to identify alternative materials that can be used to provide a durable grounding system yet not be targeted for theft. In response, EPRI is investigating the use of alternative materials for electrode designsexamining life expectancy, corrosion, material compatibility and current handl...

2010-12-23T23:59:59.000Z

253

205 kW Photovoltaic (PV) System Installed on the U.S. Department of Energy's Forrestal Building  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Project Description Project Description The Energy Policy Act of 2005 (EPAct 2005), the Energy Independence and Security Act of 2007 (EISA 2007), and Presidential Executive Order 13423 all contain requirements for Federal facilities to decrease energy consumption and increase the use of renewable energy by the year 2015. To provide leadership in meeting these requirements, DOE, in partnership with the General Services Administration (GSA), has installed a rooftop solar electric, or PV, system on the roof of DOE's headquarters in Washington, D.C. The 205 kilowatt (kW) installation is one of the largest of its kind in the Nation's capital. A display in the For- restal building will show the power output of the PV system during the day and the energy produced over

254

Enertech 15-kW wind-system development: Phase I. Design and analysis. Volume I. Executive summary  

Science Conference Proceedings (OSTI)

A utility interfaced wind machine rated for 15 kW at 9 m/s (20.1 mph) has been designed to be cost effective in 5.4 m/s (12 mph) average wind sites. Approximately 18 months into the research and development program a completed design meeting contract specifications was submitted to the buyer. The design is for a horizontal axis, down wind machine which features three fixed pitch wood-epoxy blades and free yaw. Rotor diameter is 44 feet (13.4 meters). Unit shutdown is provided by an electrohydraulic brake. Blade tip brakes provide back-up rotor overspeed protection. Design merits have been verified through dynamic truck testing of a prototype unit.

Not Available

1981-09-01T23:59:59.000Z

255

Enertech 15-kW wind-system development. Phase I. Design and Analysis. Volume II. Technical report  

SciTech Connect

A utility interfaced wind machine rated for 15 kW at 9 m/s (20.1 mph) has been designed to be cost effective in 5.4 m/s (12 mph) average wind sites. Approximately 18 months into the research and development program a completed design meeting contract specifications was submitted to the buyer. The design is for a horizontal axis, down wind machine which features three fixed pitch wood-epoxy blades and free yaw. Rotor diameter is 44 feet (13.4 meters). Unit shutdown is provided by an electrohydraulic brake. Blade tip brakes provide back-up rotor overspeed protection. Design merits have been verified through dynamic truck testing of a prototype unit.

Dodge, D.M. (ed.)

1981-09-01T23:59:59.000Z

256

Testing of a 50-kW wind-diesel hybrid system at the National Wind Technology Center  

DOE Green Energy (OSTI)

To further the development of commercial hybrid power systems, the National Renewable Energy Laboratory (NREL), in collaboration with the New World Village Power Corporation (NWVP), tested a NWVP 50-kW wind-diesel hybrid system connected to a 15/50 Atlantic Orient Corporation (AOC) wind turbine. Testing was conducted from October 1995 through March 1996 at the National Wind Technology Center (NWTC). A main objective of the testing was to better understand the application of wind turbines to weak grids typical of small villages. Performance results contained in this paper include component characterization, such as power conversion losses for the rotary converter systems and battery round trip efficiencies. In addition, systems operation over this period is discussed with special attention given to dynamic issues. Finally, future plans for continued testing and research are discussed.

Corbus, D.A.; Green, J.; Allderdice, A.; Rand, K.; Bianchi, J. [National Renewable Energy Lab., Golden, CO (United States); Linton, E. [New World Village Power, Waitsfield, VT (United States)

1996-07-01T23:59:59.000Z

257

Review of the State-of-the-Art in Power Electronics Suitable for 10-KW Military Power Systems  

SciTech Connect

The purpose of this report is to document the technological opportunities of integrating power electronics-based inverters into a TEP system, primarily in the 10-kW size range. The proposed enhancement offers potential advantages in weight reduction, improved efficiency, better performance in a wider range of generator operating conditions, greater versatility and adaptability, and adequate reliability. In order to obtain strong assurance of the availability of inverters that meet required performance and reliability levels, a market survey was performed. The survey obtained positive responses from several manufacturers in the motor drive and distributed generation industries. This study also includes technology reviews and assessments relating to circuit topologies, reliability issues, vulnerability to pulses of electromagnetic energy, potential improvements in semiconductor materials, and potential performance improvement through cryogenics.

Staunton, R.H.

2003-12-19T23:59:59.000Z

258

A 55 kW Three-Phase Inverter With Si IGBT s and SiC Schottky Diodes  

SciTech Connect

Silicon carbide (SiC) power devices are expected to have an impact on power converter efficiency, weight, volume, and reliability. Currently, only SiC Schottky diodes are commercially available at relatively low current ratings. Oak Ridge National Laboratory has collaborated with Cree and Semikron to build a Si insulated-gate bipolar transistor-SiC Schottky diode hybrid 55-kW inverter by replacing the Si p-n diodes in Semikron's automotive inverter with Cree's made-to-order higher current SiC Schottky diodes. This paper presents the developed models of these diodes for circuit simulators, shows inverter test results, and compares the results with those of a similar all-Si inverter.

Ozpineci, Burak [ORNL; Chinthavali, Madhu Sudhan [ORNL; Tolbert, Leon M [ORNL; Kashyap, Avinash S [ORNL; Mantooth, Homer A [ORNL

2006-01-01T23:59:59.000Z

259

A 55-kW Three-Phase Inverter with Si IGBTs and SiC Schottky Diodes  

SciTech Connect

Silicon carbide (SiC) power devices are expected to have an impact on power converter efficiency, weight, volume, and reliability. Currently, only SiC Schottky diodes are commercially available at relatively low current ratings. Oak Ridge National Laboratory has collaborated with Cree and Semikron to build a Si insulated-gate bipolar transistor-SiC Schottky diode hybrid 55-kW inverter by replacing the Si p-n diodes in Semikron's automotive inverter with Cree's made-to-order higher current SiC Schottky diodes. This paper presents the developed models of these diodes for circuit simulators, shows inverter test results, and compares the results with those of a similar all-Si inverter.

Tolbert, Leon M [ORNL; Ozpineci, Burak [ORNL; Chinthavali, Madhu Sudhan [ORNL; Mantooth, Homer A [ORNL; Kashyap, Avinash S [ORNL

2009-01-01T23:59:59.000Z

260

Advanced Photovoltaic Inverter Functionality using 500 kW Power Hardware-in-Loop Complete System Laboratory Testing: Preprint  

Science Conference Proceedings (OSTI)

With the increasing penetration of distribution connected photovoltaic (PV) systems, more and more PV developers and utilities are interested in easing future PV interconnection concerns by mitigating some of the impacts of PV integration using advanced PV inverter controls and functions. This paper describes the testing of a 500 kW PV inverter using Power Hardware-in-Loop (PHIL) testing techniques. The test setup is described and the results from testing the inverter in advanced functionality modes, not commonly used in currently interconnected PV systems, are presented. PV inverter operation under PHIL evaluation that emulated both the DC PV array connection and the AC distribution level grid connection are shown for constant power factor (PF) and constant reactive power (VAr) control modes. The evaluation of these modes was completed under varying degrees of modeled PV variability.

Mather, B. A.; Kromer, M. A.; Casey, L.

2013-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "kw ground mounted" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Development of a Residential Ground-Source Integrated Heat Pump  

Science Conference Proceedings (OSTI)

A residential-size ground-source integrated heat pump (GSIHP) system has been developed and is currently being field tested. The system is a nominal 2-ton (7 kW) cooling capacity, variable-speed unit, which is multi-functional, e.g. space cooling, space heating, dedicated water heating, and simultaneous space cooling and water heating. High-efficiency brushless permanent-magnet (BPM) motors are used for the compressor, indoor blower, and pumps to obtain the highest component performance and system control flexibility. Laboratory test data were used to calibrate a vapor-compression simulation model (HPDM) for each of the four primary modes of operation. The model was used to optimize the internal control options and to simulate the selected internal control strategies, such as controlling to a constant air supply temperature in the space heating mode and a fixed water temperature rise in water heating modes. Equipment performance maps were generated for each operation mode as functions of all independent variables for use in TRNSYS annual energy simulations. These were performed for the GSIHP installed in a well-insulated 2600 ft2(242 m2) house and connected to a vertical ground loop heat exchanger(GLHE). We selected a 13 SEER (3.8 CSPF )/7.7 HSPF (2.3 HSPF, W/W) ASHP unit with 0.90 Energy Factor (EF) resistance water heater as the baseline for energy savings comparisons. The annual energy simulations were conducted over five US climate zones. In addition, appropriate ground loop sizes were determined for each location to meet 10-year minimum and maximum design entering water temperatures (EWTs) to the equipment. The prototype GSIHP system was predicted to use 52 to 59% less energy than the baseline system while meeting total annual space conditioning and water heating loads.

Rice, C Keith [ORNL; Baxter, Van D [ORNL; Hern, Shawn [ClimateMaster, Inc.; McDowell, Tim [Thermal Energy System Specialists, LLC; Munk, Jeffrey D [ORNL; Shen, Bo [ORNL

2013-01-01T23:59:59.000Z

262

Hydrothermal Circulation At Mount St Helens Determined By Self-Potential  

Open Energy Info (EERE)

source source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit History Facebook icon Twitter icon » Hydrothermal Circulation At Mount St Helens Determined By Self-Potential Measurements Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: Hydrothermal Circulation At Mount St Helens Determined By Self-Potential Measurements Details Activities (1) Areas (1) Regions (0) Abstract: The distribution of hydrothermal circulation within active volcanoes is of importance in identifying regions of hydrothermal alteration which may in turn control explosivity, slope stability and sector collapse. Self-potential measurements, indicative of fluid circulation, were made within the crater of Mount St. Helens in 2000 and

263

Pioneering the New Grid: Pole-mounted Solar | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Pioneering the New Grid: Pole-mounted Solar Pioneering the New Grid: Pole-mounted Solar Pioneering the New Grid: Pole-mounted Solar May 7, 2010 - 10:54am Addthis SunWave solar power systems are attached to utility poles, where they can gather sun power as well as provide a point of data gathering for utility companies to monitor the grid. | Photo courtesy Petra Solar SunWave solar power systems are attached to utility poles, where they can gather sun power as well as provide a point of data gathering for utility companies to monitor the grid. | Photo courtesy Petra Solar Joshua DeLung What does this mean for me? About 25,000 SunWave panels -- which generate energy for the grid as well as communicate an energy snapshot at that point -- are already in operation, with a further expected 200,000 installations.

264

Pioneering the New Grid: Pole-mounted Solar | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Pioneering the New Grid: Pole-mounted Solar Pioneering the New Grid: Pole-mounted Solar Pioneering the New Grid: Pole-mounted Solar May 7, 2010 - 10:54am Addthis SunWave solar power systems are attached to utility poles, where they can gather sun power as well as provide a point of data gathering for utility companies to monitor the grid. | Photo courtesy Petra Solar SunWave solar power systems are attached to utility poles, where they can gather sun power as well as provide a point of data gathering for utility companies to monitor the grid. | Photo courtesy Petra Solar Joshua DeLung What does this mean for me? About 25,000 SunWave panels -- which generate energy for the grid as well as communicate an energy snapshot at that point -- are already in operation, with a further expected 200,000 installations.

265

DOE Partnership Completes Successful CO2 Injection Test in the Mount Simon  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Partnership Completes Successful CO2 Injection Test in the Partnership Completes Successful CO2 Injection Test in the Mount Simon Sandstone DOE Partnership Completes Successful CO2 Injection Test in the Mount Simon Sandstone October 21, 2009 - 1:00pm Addthis Washington, DC - The Midwest Regional Carbon Sequestration Partnership (MRCSP), one of seven partnerships in the U.S. Department of Energy's Regional Carbon Sequestration Partnerships program, has successfully injected 1,000 metric tons of carbon dioxide (CO2) into the Mount Simon Sandstone, a deep saline formation that is widespread across much of the Midwest. Preliminary results indicate that the formation has good CO2 storage potential and could possibly serve as a repository for CO2 emissions captured from stationary sources in the region. Carbon capture and storage

266

Integrated crystal mounting and alignment system for high-throughput biological crystallography  

DOE Patents (OSTI)

A method and apparatus for the transportation, remote and unattended mounting, and visual alignment and monitoring of protein crystals for synchrotron generated x-ray diffraction analysis. The protein samples are maintained at liquid nitrogen temperatures at all times: during shipment, before mounting, mounting, alignment, data acquisition and following removal. The samples must additionally be stably aligned to within a few microns at a point in space. The ability to accurately perform these tasks remotely and automatically leads to a significant increase in sample throughput and reliability for high-volume protein characterization efforts. Since the protein samples are placed in a shipping-compatible layered stack of sample cassettes each holding many samples, a large number of samples can be shipped in a single cryogenic shipping container.

Nordmeyer, Robert A. (San Leandro, CA); Snell, Gyorgy P. (Richmond, CA); Cornell, Earl W. (Antioch, CA); Kolbe, William F. (Moraga, CA); Yegian, Derek T. (Oakland, CA); Earnest, Thomas N. (Berkeley, CA); Jaklevich, Joseph M. (Lafayette, CA); Cork, Carl W. (Walnut Creek, CA); Santarsiero, Bernard D. (Chicago, IL); Stevens, Raymond C. (La Jolla, CA)

2007-09-25T23:59:59.000Z

267

Water heater with an improved thermostat mounting and a method of making such water heaters  

Science Conference Proceedings (OSTI)

An improvement in an electric water heater is described comprising: a non-metallic tank, a cold water inlet, a hot water outlet, an electrical heating means adapted to heat a body of water contained in the tank and a thermostat having a sensing face with a given area controlling the flow of electric current to the heating means, the improvement comprising a thermally conductive thermostat mounting plate having a surface area substantially larger than the sensing face given area in direct contact with the tank and a thermostat retention means releasably holding the thermostat in contact with the thermostat mounting plate.

Moore, H.J.; Deneau, M.E.

1993-06-15T23:59:59.000Z

268

Colorado Ground Water Commission | Open Energy Information  

Open Energy Info (EERE)

Water Commission Jump to: navigation, search Name Colorado Ground Water Commission Place Colorado Website http:water.state.co.usgroun References Colorado Ground Water Commission...

269

Approximating the Seismic Amplification Effects Experienced by Solar Towers Mounted on the Rooftops of Low-Rise Industrial Buildings.  

E-Print Network (OSTI)

?? This thesis investigates the acceleration amplification experienced by solar towers mounted on the rooftops of low-rise industrial buildings during a seismic event. Specifically, this… (more)

Balla, Peter Luiz

2013-01-01T23:59:59.000Z

270

Transient analysis of grounding systems  

SciTech Connect

This paper addresses the problem of computing the ground potential rise of grounding systems during transients. Finite element analysis is employed to model the constituent parts of a grounding system. Short lengths of earth embedded electrodes are characterized as transmission lines with distributed inductance, capacitance and leakage resistance to earth. Leakage resistance to earth is accurately computed with the method of moments. The other parameters of the finite element, namely inductance and capacitance, are computed from the resistance utilizing Maxwell's equations. This modeling enables the computation of the transient response of substation grounding systems to fast or slow waves striking the substation. The result is obtained in terms of a convolution of the step response of the system and the striking wave. In this way the impedance of substation systems to 60 cycles is accurately computed. Results demonstrate the dependence of the 60 cycle impedance on system parameters. The methodology allows to interface this model of a substation ground mat with the Electromagnetic Transient Analysis Program thus, allowing explicit representation of earth effects in electromagmatic transients computations.

Meliopoulos, A.P.; Moharam, M.G.

1983-02-01T23:59:59.000Z

271

Ground Magnetics | Open Energy Information  

Open Energy Info (EERE)

Ground Magnetics Ground Magnetics Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Technique: Ground Magnetics Details Activities (15) Areas (12) Regions (0) NEPA(1) Exploration Technique Information Exploration Group: Geophysical Techniques Exploration Sub Group: Magnetic Techniques Parent Exploration Technique: Magnetic Techniques Information Provided by Technique Lithology: Presence of magnetic minerals such as magnetite. Stratigraphic/Structural: Mapping of basement structures, horst blocks, fault systems, fracture zones, dykes and intrusions. Hydrological: The circulation of hydrothermal fluid may impact the magnetic susceptibility of rocks. Thermal: Rocks lose their magnetic properties at the Curie temperature (580° C for magnetite) [1] and, upon cooling, remagnetize in the present magnetic field orientation. The Curie point depth in the subsurface may be determined in a magnetic survey to provide information about hydrothermal activity in a region.

272

40-kW field test power plant modification and development. Monthly technical status report No. 13, September 16, 1978-October 15, 1978  

DOE Green Energy (OSTI)

The contract objective is to complete the design and development actions that upgrade the 40-kW fuel cell power plant to a configuration suitable for on-site demonstration testing. The modifications will improve operating capability, durability and maintenance interval and lead to reduced production costs. Equipment to recover and use the by-product heat of electric generation will be available on the power plant for field verification of on-site heat recovery. The 40-kW power plant will be compatible with the power characteristics required for conventional heat pumps and conventional 60 Hz, 120/208 volts electrically operated equipment. Progress is reported. (WHK)

Not Available

1978-11-10T23:59:59.000Z

273

NedPower Mount Storm II Wind Farm | Open Energy Information  

Open Energy Info (EERE)

NedPower Mount Storm II Wind Farm NedPower Mount Storm II Wind Farm Jump to: navigation, search Name NedPower Mount Storm II Wind Farm Facility NedPower Mount Storm II Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner Shell Wind Energy/Dominion Energy Developer NedPower/Shell Wind Energy/Dominion Energy Energy Purchaser Dominion Energy Location Grant County WV Coordinates 39.251507°, -79.178989° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":39.251507,"lon":-79.178989,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

274

The February 2001 Eruption of Mount Cleveland, Alaska: Case Study of an Aviation Hazard  

Science Conference Proceedings (OSTI)

Mount Cleveland, Alaska (52°49?N, 169°57?W), located on Chuginadak Island, erupted on 19 February 2001. The atmosphere–volcanic plume interactions that occurred as part of this event led to several serious encounters of commercial aircraft with ...

James J. Simpson; Jared S. Berg; Gary L. Hufford; Craig Bauer; David Pieri; René Servranckx

2002-08-01T23:59:59.000Z

275

Head-mounted and multi-surface displays support emergency medical teams  

Science Conference Proceedings (OSTI)

Emergency medical teams collaborate to solve problems and take care of patients under time pressure and high cognitive load, in noisy and complex environments. This paper presents preliminary work in the design and evaluation of head-mounted and multi-surface ... Keywords: checklists, hmd, hud, large displays, medical interfaces

Leslie Wu; Jesse Cirimele; Jonathan Bassen; Kristen Leach; Stuart Card; Larry Chu; Kyle Harrison; Scott Klemmer

2013-02-01T23:59:59.000Z

276

Apparatus and method for mounting photovoltaic power generating systems on buildings  

DOE Patents (OSTI)

Rectangular PV modules (6) are mounted on a building roof (4) by mounting stands that are distributed in rows and columns. Each stand comprises a base plate (10) that rests on the building roof (4) and first and second brackets (12, 14) of different height attached to opposite ends of the base plate (10). Each bracket (12, 14) has dual members for supporting two different PV modules (6), and each PV module (6) has a mounting pin (84) adjacent to each of its four corners. Each module (6) is supported by attachment of two of its mounting pins (84) to different first brackets (12), whereby the modules (6) and their supporting stands are able to resist uplift forces resulting from high velocity winds without the base plates (10) being physically attached to the supporting roof structure (4). Preferably the second brackets (14) have a telescoping construction that permits their effective height to vary from less than to substantially the same as that of the first brackets (12).

Russell, Miles Clayton (Lincoln, MA)

2008-10-14T23:59:59.000Z

277

Systematic hydraulic study on pumping stations equipped with surge tank mounted next to the pump  

Science Conference Proceedings (OSTI)

An important number of pumping stations, part of the Romanian irrigation systems, were conceived with surge tank mounted on the discharge duct, next to the pump, in order to protect the installation from hydraulic shock. In practice, the dimensioning ... Keywords: air chamber, geodetic head, head loss, pumping station, surge tank

Claudiu Stefan Nitescu; Anca Constantin

2010-07-01T23:59:59.000Z

278

Rainfall Anomaly over the Lee Side of Mount Carmel (Israel) and the Associated Wind Field  

Science Conference Proceedings (OSTI)

Yagur and other rain gauge stations located on the lee side of Mount Carmel in Israel experience much higher amounts of precipitation than those measured on the windward side of the mountain at a similar altitude and more rain than stations on ...

Yair Goldreich; Ariel Freundlich; Pinhas Alpert

1997-06-01T23:59:59.000Z

279

Commercial Kitchen Ventilation Performance Report: Gas Underfired Broiler Under Wall-Mounted Canopy Hood  

Science Conference Proceedings (OSTI)

This report documents testing of ventilation requirements for a gas underfired broiler under a wall-mounted canopy hood. This appliance and hood combination is one of a series undertaken to provide electric utilities and the foodservice industry with data to optimize the design of commercial kitchen ventilation systems and integrate exhaust requirements with space conditioning design.

1997-11-14T23:59:59.000Z

280

Commercial Kitchen Ventilation Performance Report: Two Gas Pressure Fryers Under Wall-Mounted Canopy Hood  

Science Conference Proceedings (OSTI)

This report documents testing of ventilation requirements two gas pressure fryers under a wall-mounted canopy hood. This appliance and hood combination is one of a series undertaken to provide electric utilities and the foodservice industry with data to optimize the design of commercial kitchen ventilation systems and integrate exhaust requirements with space conditioning design.

1997-10-31T23:59:59.000Z

Note: This page contains sample records for the topic "kw ground mounted" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Commercial Kitchen Ventilation Performance Report: Two Electric Pressure Fryers Under Wall-Mounted Canopy Hood  

Science Conference Proceedings (OSTI)

This report documents testing of ventilation requirements for two electric pressure fryers under a wall-mounted canopy hood. This appliance and hood combination is one of a series undertaken to provide electric utilities and the foodservice industry with data to optimize the design of commercial kitchen ventilation systems and integrate exhaust requirements with space conditioning design.

1997-09-17T23:59:59.000Z

282

Method of making cascaded die mountings with springs-loaded contact-bond options  

DOE Patents (OSTI)

A cascaded die mounting device and method using spring contacts for die attachment, with or without metallic bonds between the contacts and the dies, is disclosed. One embodiment is for the direct refrigerant cooling of an inverter/converter carrying higher power levels than most of the low power circuits previously taught, and does not require using a heat sink.

Hsu, John S. (Oak Ridge, TN); Adams, Donald J. (Knoxville, TN); Su, Gui-Jia (Knoxville, TN); Marlino, Laura D. (Oak Ridge, TN); Ayers, Curtis W. (Kingston, TN); Coomer, Chester (Knoxville, TN)

2007-06-19T23:59:59.000Z

283

Scoping Study: Surface Mount Technology and Applications in Power Electronics and Control Systems  

Science Conference Proceedings (OSTI)

The electronics packaging industry has not seen a revolution of the magnitude of surface mount technology (SMT) since the development of the printed wiring board. This study examines the rapid shift toward SMT and provides an overview of SMT applications for power electronics and controls equipment manufacturers.

1996-10-06T23:59:59.000Z

284

Ground Truth: A Positive Cloud-to-Ground Lightning Flash  

Science Conference Proceedings (OSTI)

We describe the circumstances and effects of a cloud-to-ground lightning flash that lowered positive charge and struck a residential home near Albany, New York. The characteristics of the flash were detected and recorded by a wide-band magnetic ...

Vincent P. Idone; Richard E. Orville; Ronald W. Henderson

1984-07-01T23:59:59.000Z

285

Ground states in complex bodies  

E-Print Network (OSTI)

A unified framework for analyzing the existence of ground states in wide classes of elastic complex bodies is presented here. The approach makes use of classical semicontinuity results, Sobolev mappinngs and Cartesian currents. Weak diffeomorphisms are used to represent macroscopic deformations. Sobolev maps and Cartesian currents describe the inner substructure of the material elements. Balance equations for irregular minimizers are derived. A contribution to the debate about the role of the balance of configurational actions follows. After describing a list of possible applications of the general results collected here, a concrete discussion of the existence of ground states in thermodynamically stable quasicrystals is presented at the end.

Paolo Maria Mariano; Giuseppe Modica

2008-02-11T23:59:59.000Z

286

LINE-ABOVE-GROUND ATTENUATOR  

DOE Patents (OSTI)

The line-above-ground attenuator provides a continuously variable microwave attenuator for a coaxial line that is capable of high attenuation and low insertion loss. The device consists of a short section of the line-above- ground plane type transmission lime, a pair of identical rectangular slabs of lossy material like polytron, whose longitudinal axes are parallel to and indentically spaced away from either side of the line, and a geared mechanism to adjust amd maintain this spaced relationship. This device permits optimum fineness and accuracy of attenuator control which heretofore has been difficult to achieve.

Wilds, R.B.; Ames, J.R.

1957-09-24T23:59:59.000Z

287

kW  

Science Conference Proceedings (OSTI)

This presentation will discussed the delaminating superficial failure of a low wear coating (SnSb12Cu6Pb following DIN-ISO-4381) under emergency working ...

288

DARPA Learning Applied to Ground Robots (LAGR)  

Science Conference Proceedings (OSTI)

DARPA Learning Applied to Ground Robots (LAGR) Project (Concluded). Summary: The National Institute of Standards ...

2012-01-04T23:59:59.000Z

289

Final phase testing and evaluation of the 500 kW direct contact pilot plant at East Mesa  

DOE Green Energy (OSTI)

The testing performed during the last phase of the geothermal direct contact heat exchanger program utilizing the 500 kW pilot plant provided more insight into the capabilities and limits of the direct contact approach and showed that more work needs to be done to understand the inner workings of a large direct contact heat exchanger if they are to be modeled analytically. Testing of the column demonstrated that the performance was excellent and that the sizing criteria is conservative. The system operated smoothly and was readily controlled over a wide range of operating conditions. Performance evaluation showed pinch differentials of 4/sup 0/F or less and better than predicted heat transfer capability. Testing during this final phase was directed towards establishing the limits of the column to transfer heat. The working column height was shortened progressively to approximately 16 feet from a design length of 28 feet. The short column performed as well as a full length column and there are indications that the column could have been shortened even more without affecting its ability to transfer heat. The column's ability to perform as well with shortened lengths indicates that the heat transfer coefficients and criteria derived from the small scale tests are very conservative.

Olander, R.; Oshmyansky, S.; Nichols, K.; Werner, D.

1983-12-01T23:59:59.000Z

290

Testing of a 50-kW Wind-Diesel Hybrid System at the National Wind Technology Center  

DOE Green Energy (OSTI)

In remote off-grid villages and communities, a reliable power source is important in improving the local quality of life. Villages often use a diesel generator for their power, but fuel can be expensive and maintenance burdensome. Including a wind turbine in a diesel system can reduce fuel consumption and lower maintenance, thereby reducing energy costs. However, integrating the various components of a wind-diesel system, including wind turbine, power conversion system, and battery storage (if applicable), is a challenging task. To further the development of commercial hybrid power systems, the National Renewable Energy Laboratory (NREL), in collaboration with the New World Village Power Corporation (NWVP), tested a NWVP 50-kW wind-diesel hybrid system connected to a 15/50 Atlantic Orient Corporation (AOC) wind turbine. Testing was conducted from October 1995 through March 1996 at the National Wind Technology Center (NWTC). A main objective of the testing was to better understand the application of wind turbines to weak grids typical of small villages. Performance results contained in this report include component characterization, such as power conversion losses for the rotary converter system and battery round trip efficiencies. In addition, system operation over the test period is discussed with special attention given to dynamic issues. Finally, future plans for continued testing and research are discussed.

Corbus, D. A.; Green, H. J.; Allderdice, A.; Rand, K.; Bianchi, J.; Linton, E.

1996-07-01T23:59:59.000Z

291

Maximization of No-Load Flux Density in Surface Mounted Permanent Magnet Motors Frdric DUBAS, Christophe ESPANET & Abdellatif MIRAOUI.  

E-Print Network (OSTI)

Maximization of No-Load Flux Density in Surface Mounted Permanent Magnet Motors Frédéric DUBAS mounted permanent magnet motors having a direction of parallel or radial magnetization [1]. I expression of the optimal thickness of the magnet which make it possible to maximize the no-load flux density

Paris-Sud XI, Université de

292

Casa de Oro-Mount Helix, California: Energy Resources | Open Energy  

Open Energy Info (EERE)

Oro-Mount Helix, California: Energy Resources Oro-Mount Helix, California: Energy Resources Jump to: navigation, search Equivalent URI DBpedia Coordinates 32.7622263°, -116.9793554° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":32.7622263,"lon":-116.9793554,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

293

Mirror mounts designed for the Advanced Photon Source SRI-CAT  

SciTech Connect

Use of a mirror for beamlines at third-generation synchrotron radiation facilities, such as the Advanced Photon Source (APS) at Argonne National laboratory, has many advantages. A mirror as a first optical component provides significant reduction in the beam peak heat flux and total power on the downstream monochromator and simplifies the bremsstrahlung shielding design for the beamline transport. It also allows one to have a system for multibeamline branching and switching. More generally, a mirror is used for beam focusing and/or low-pass filtering. Six different mirror mounts have been designed for the SRI-CAT beamlines. Four of them are designed as water-cooled mirrors for white or pink beam use, and the other two are for monochromatic beam use. Mirror mount designs, including vacuum vessel structure and precision supporting stages, are presented in this paper.

Shu, D.; Benson, C.; Chang, J. [and others

1997-09-01T23:59:59.000Z

294

NETL: News Release - Vehicle-Mounted Natural Gas Leak Detector Passes Key  

NLE Websites -- All DOE Office Websites (Extended Search)

October 2, 2003 October 2, 2003 Vehicle-Mounted Natural Gas Leak Detector Passes Key "Road Test" Spots Natural Gas Leaks from 30 Feet Away At Speeds Approaching 20 Miles Per Hour Handheld Prototype Gas Detector Now Being Outfitted as a Van-Mounted Unit PSI has modified this early prototype of a handheld remote natural gas detector to operate from a moving vehicle. ANDOVER, MA - Physical Sciences Inc. (PSI) recently conducted a successful test of its mobile natural gas detector at the company's research facilities in Andover, Mass. PSI's prototype leak detector demonstrated its ability to spot natural gas leaks from a distance of up to 30 feet from a vehicle moving at speeds approaching 20 miles per hour. In the United States, significant resources are devoted annually to leak

295

Ground Magnetics (Nannini, 1986) | Open Energy Information  

Open Energy Info (EERE)

Ground Magnetics (Nannini, 1986) Ground Magnetics (Nannini, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Ground Magnetics (Nannini, 1986) Exploration Activity Details Location Unspecified Exploration Technique Ground Magnetics Activity Date Usefulness not indicated DOE-funding Unknown Notes Detection and quantitative assessment of such intrusive events can be facilitated by magnetic surveys (ground or aerial magnetic field measurements). These surveys are based on the magnetic susceptibility contrast between magmatic rocks at depth and the sedimentary formations above. References Raffaello Nannini (1986) Some Aspects Of Exploration In Non-Volcanic Areas Retrieved from "http://en.openei.org/w/index.php?title=Ground_Magnetics_(Nannini,_1986)&oldid=388291

296

A cathodically protected electrical substation ground grid  

SciTech Connect

This paper presents a discussion on the design of a cathodically protected electrical substation grounding system in which a steel ground grid and steel ground rods were used in place of the commonly used copper ground grid and copperweld ground rods. Several electrical constraints are presented which discuss common electrical utility requirements, safety considerations and economic factors. The grounding system materials which were chosen are discussed along with the means of cathodic protection. Finally, the design, construction and testing considerations are presented as an aid to others who wish to design a similar system.

Nelson, J.P.; Holm, W.K.

1983-09-01T23:59:59.000Z

297

Distribution Grounding of Underground Facilities  

Science Conference Proceedings (OSTI)

This report describes Phase I of a two-phase project to assess industry practices and standards for grounding and bonding of medium-voltage underground residential distribution (URD) and underground commercial distribution (UCD) circuits and worker safety in worksites with these systems.The report includes an overview of the issues and concerns associated with underground distribution systems safety and, in particular, worker safety in worksites. It identifies the industry and utility ...

2013-12-20T23:59:59.000Z

298

Acoustically Mounted Microcrystals Yield High-Resolution X-ray Structures  

SciTech Connect

We demonstrate a general strategy for determining structures from showers of microcrystals. It uses acoustic droplet ejection to transfer 2.5 nL droplets from the surface of microcrystal slurries, through the air, onto mounting micromesh pins. Individual microcrystals are located by raster-scanning a several-micrometer X-ray beam across the cryocooled micromeshes. X-ray diffraction data sets merged from several micrometer-sized crystals are used to determine 1.8 {angstrom} resolution crystal structures.

Soares, Alexei S.; Engel, Matthew A.; Stearns, Richard; Datwani, Sammy; Olechno, Joe; Ellson, Richard; Skinner, John M.; Allaire, Marc; Orville, Allen M. (Labcyte); (BNL)

2012-10-25T23:59:59.000Z

299

Materials Reliability Program: PWR Bottom Mounted Nozzle (BMN) Issue Response Handbook (MRP-372)  

Science Conference Proceedings (OSTI)

Resolution of a case of primary water stress corrosion cracking (PWSCC) detected in a bottom mounted nozzle (BMN) could be expected to require substantial utility resources, even if only a single nozzle were to be affected, because of the challenges in accessing it in pressurized water reactors (PWRs) to perform inspections and repairs. This Handbook compiles the available knowledge and reference information to guide utility development of a site-specific response plan to an emergent BMN ...

2013-11-14T23:59:59.000Z

300

Solar energy system installed at Mount Rushmore National Visitor Center in Keystone, South Dakota  

SciTech Connect

Information is provided on the system description, the design, and installation of the solar energy system installed at the Mount Rushmore Visitor Center. The system is designed to furnish about 45 percent of the heating for the total facility and about 53 percent partial cooling for the 2000 square-foot observatory. Such items as Acceptance Test Data, a complete set of as-build drawings, system performance data, problems, pictures, and other pertinent materials are included.

1979-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "kw ground mounted" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Base excitation testing system using spring elements to pivotally mount wind turbine blades  

DOE Patents (OSTI)

A system (1100) for fatigue testing wind turbine blades (1102) through forced or resonant excitation of the base (1104) of a blade (1102). The system (1100) includes a test stand (1112) and a restoring spring assembly (1120) mounted on the test stand (1112). The restoring spring assembly (1120) includes a primary spring element (1124) that extends outward from the test stand (1112) to a blade mounting plate (1130) configured to receive a base (1104) of blade (1102). During fatigue testing, a supported base (1104) of a blad (1102) may be pivotally mounted to the test stand (1112) via the restoring spring assembly (1120). The system (1100) may include an excitation input assembly (1140) that is interconnected with the blade mouting plate (1130) to selectively apply flapwise, edgewise, and/or pitch excitation forces. The restoring spring assemply (1120) may include at least one tuning spring member (1127) positioned adjacent to the primary spring element (1124) used to tune the spring constant or stiffness of the primary spring element (1124) in one of the excitation directions.

Cotrell, Jason; Hughes, Scott; Butterfield, Sandy; Lambert, Scott

2013-12-10T23:59:59.000Z

302

Warm or Steaming Ground | Open Energy Information  

Open Energy Info (EERE)

Warm or Steaming Ground Warm or Steaming Ground Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Print PDF Warm or Steaming Ground Dictionary.png Warm or Steaming Ground: An area where geothermal heat is conducted to the earth's surface, warming the ground and sometimes causing steam to form when water is present. Other definitions:Wikipedia Reegle Modern Geothermal Features Typical list of modern geothermal features Hot Springs Fumaroles Warm or Steaming Ground Mudpots, Mud Pools, or Mud Volcanoes Geysers Blind Geothermal System Steam rising from the ground at Eldvorp, a 10 km row of craters, in Southwestern Iceland. http://www.visiticeland.com/SearchResults/Attraction/eldvorp Warm or steaming ground is often an indicator of a geothermal system beneath the surface. In some cases a geothermal system may not show any

303

Ground Plane Identification Using LIDAR in Forested  

E-Print Network (OSTI)

To operate autonomously in forested environments, unmanned ground vehicles (UGVs) must be able to identify the load-bearing surface of the terrain (i.e. the ground). This paper presents a novel two-stage approach for ...

McDaniel, Matt W.

304

Directional Reactive Power Ground Plane Transmission  

Directional Reactive Power Ground Plane Transmission Technology Summary ... The invention can transmit electrical power through the surface of the ...

305

US ARMY GROUND VEHICLE CREW COMPARTMENT ...  

Science Conference Proceedings (OSTI)

... test fixture was constructed from an excess ground vehicle hull ... instrumentation measured acid gas exposure levels: ion selective electrodes (grab ...

2011-10-04T23:59:59.000Z

306

Sizing of Overhead Ground Wires for Lightning  

Science Conference Proceedings (OSTI)

Overhead ground wires, or shield wires, are placed on transmission lines as air terminals for lightning strikes to shield the phase conductors from direct strikes. Although of short duration, lightning strikes to ground wires may result in significant damage. Utilities are increasingly using optical fiber ground wires (OPGWs), and severe damage to the OPGWs could result in failure of the communication link. There is renewed interest in the dimensioning and testing of ground wires for improved ...

2012-12-12T23:59:59.000Z

307

Modeling reducibility on ground terms using constraints  

E-Print Network (OSTI)

Modeling reducibility on ground terms using constraints Isabelle GNAEDIGa , H´el`ene KIRCHNERb a on ground terms using (dis)equational constraints. We show in particular that innermost (ir)reducibility can on the ground term algebra that any rewriting chain starting from any term termi- nates, provided that terms

Paris-Sud XI, Université de

308

Adaptation of a commercially available 200 kW natural gas fuel cell power plant for operation on a hydrogen rich gas stream  

DOE Green Energy (OSTI)

International Fuel Cells (IFC) has designed a hydrogen fueled fuel cell power plant based on a modification of its standard natural gas fueled PC25{trademark} C fuel cell power plant. The natural gas fueled PC25 C is a 200 kW, fuel cell power plant that is commercially available. The program to accomplish the fuel change involved deleting the natural gas processing elements, designing a new fuel pretreatment subsystem, modifying the water and thermal management subsystem, developing a hydrogen burner to combust unconsumed hydrogen, and modifying the control system. Additionally, the required modifications to the manufacturing and assembly procedures necessary to allow the hydrogen fueled power plant to be manufactured in conjunction with the on-going production of the standard PC25 C power plants were identified. This work establishes the design and manufacturing plan for the 200 kW hydrogen fueled PC25 power plant.

Maston, V.A.

1997-12-01T23:59:59.000Z

309

Assessment of a Transportable 200-kW Fuel Cell in Rural Applications: Site 1: Central Georgia EMC/Oglethorpe Power Corporation, Jack son, Georgia  

Science Conference Proceedings (OSTI)

Dispersed generation is particularly attractive to electric cooperatives in rural areas due to low customer densities and sometimes rapid load growth at the end of long lines. EPRI and the National Rural Electric Cooperative Association (NRECA) are cosponsoring a project to demonstrate the use of transportable 200 kW phosphoric acid fuel cell power plants in rural dispersed generation applications. This interim report details the project and describes the first year of operation of a transportable fuel c...

1997-12-30T23:59:59.000Z

310

Southern Company Photovoltaic Evaluation in Atlanta: Analysis of Field Data from Seven 4-kW PV Systems at Georgia Power Headquarters During 2010–2012  

Science Conference Proceedings (OSTI)

Seven photovoltaic (PV) power systems using different module technologies were installed on the rooftop of Georgia Power’s headquarters in Atlanta. This report describes the output performance of these small-scale systems (about 4 kW each) relative to the available solar resource at the site. The main objective of this evaluation has been to assess performance characteristics of commercially available module technologies in a southeastern U.S. climate. To ensure a reliable comparison, all ...

2013-01-28T23:59:59.000Z

311

Low-cost light-weight efficient 1. 5 kW inverters with and without output transformers. Final report, January 1976--June 1977  

SciTech Connect

Optimization efforts were completed on the 1.5 kW inverter described in report DECC-61098-003 (September 1975). A second inverter design was developed; in the second design the output transformer was eliminated. Tests were performed on both the optimized transformer-output inverter and the transformerless-output inverter. Tests included environmental tests on the transformer-output inverter. (Author)

Suelzle, L.R.; Suelzle, J.S.

1977-10-01T23:59:59.000Z

312

Concepts for a bottom-mounted buoyant, stab-in cold water pipe for the OTEC program  

DOE Green Energy (OSTI)

A conceptual design for a bottom-mounted, stab-in cold water pipe (CWP) for OTEC is presented. The design concepts used are based on experience gained in the design of marine risers for offshore petroleum production. After a detailed description of the system envisioned and the installation scenario, the status of the major components in the system is discussed relative to the present state of the art in the oil industry. From preliminary structural analyses and cost projections, a comparison is then drawn between the bottom-mounted pipe and free-hanging CWP designs. The comparison shows the bottom-mounted concept to be technically and economically sound, utilizing present oil industry design practices. Finally, recommendations are made for further work to integrate the bottom-mounted CWP concept into the OTEC program.

Pompa, J.A.; Key, J.W.

1979-01-01T23:59:59.000Z

313

Dewpoint and Humidity Measurements and Trends at the Summit of Mount Washington, New Hampshire, 1935–2004  

Science Conference Proceedings (OSTI)

Meteorological conditions have been recorded at the summit of Mount Washington, New Hampshire, (44°16?N, 71°18?W, 1914 m ASL) since November 1932. Use of consistent instrumentation allows analysis of humidity measurements as calculated from error-...

Thomas M. Seidel; Andrea N. Grant; Alexander A. P. Pszenny; Daniel J. Allman

2007-11-01T23:59:59.000Z

314

Isotope Brayton ground demonstration testing and flight qualification. Volume 1. Technical program  

SciTech Connect

A program is proposed for the ground demonstration, development, and flight qualification of a radioisotope nuclear heated dynamic power system for use on space missions beginning in the 1980's. This type of electrical power system is based upon and combines two aerospace technologies currently under intense development; namely, the MHW isotope heat source and the closed Brayton cycle gas turbine. This power system represents the next generation of reliable, efficient economic electrical power equipment for space, and will be capable of providing 0.5 to 2.0 kW of electric power to a wide variety of spacecraft for earth orbital and interplanetary missions. The immediate design will be based upon the requirements for the Air Force SURVSATCOM mission. The proposal is presented in three volumes plus an Executive Summary. This volume describes the tasks in the technical program.

1974-12-09T23:59:59.000Z

315

Building Energy Software Tools Directory: Ground Loop Design  

NLE Websites -- All DOE Office Websites (Extended Search)

Loop Design Ground Loop Design logo Ground Loop Design is a versatile ground source heat pump system design program that helps the trained geothermal HVAC designerengineer...

316

Work plan for the fabrication of the radioisotope thermoelectric generator transportation system package mounting  

DOE Green Energy (OSTI)

The Radioisotope Thermoelectric Generator (RTG) has available a dedicated system for the transportation of RTG payloads. The RTG Transportation System (System 100) is comprised of four systems; the Package (System 120), the Semi-trailer (System 140), the Gas Management (System 160), and the Facility Transport (System 180). This document provides guidelines on the fabrication, technical requirements, and quality assurance of the Package Mounting (Subsystem 145), part of System 140. The description follows the Development Control Requirements of WHC-CM-6-1, EP 2.4, Rev. 3.

Satoh, J.A.

1994-11-09T23:59:59.000Z

317

Model-oriented ocean tomography using higher frequency, bottom-mounted hydrophones  

Science Conference Proceedings (OSTI)

A tomographic scheme is presented that ingests ocean acoustic measurements into an ocean model using data from bottom-mounted hydrophones. The short distances between source-receiver pairs (1–10 km) means arrival times at frequencies of 8–11 kHz are readily detectable and often distinguishable. The influence of ocean surface motion causes considerable variability in acoustic travel times. Techniques are presented for measuring travel times and removing the variability due to surface waves. An assimilation technique is investigated that uses differences in measured and modeled acoustic travel times to impose corrections on the oceanographic model. Equations relating travel time differences to oceanographic variables are derived

James K. Lewis; Jason Rudzinsky; Subramaniam Rajan; Peter J. Stein; Amy Vandiver; The KauaiEx Group

2005-01-01T23:59:59.000Z

318

Passive pavement-mounted acoustical linguistic drive alert system and method  

DOE Patents (OSTI)

Systems and methods are described for passive pavement-mounted acoustical alert of the occupants of a vehicle. A method of notifying a vehicle occupant includes providing a driving medium upon which a vehicle is to be driven; and texturing a portion of the driving medium such that the textured portion interacts with the vehicle to produce audible signals, the textured portion pattern such that a linguistic message is encoded into the audible signals. The systems and methods provide advantages because information can be conveyed to the occupants of the vehicle based on the location of the vehicle relative to the textured surface.

Kisner, Roger A. (Knoxville, TN); Anderson, Richard L. (Oak Ridge, TN); Carnal, Charles L. (Cookeville, TN); Hylton, James O. (Clinton, TN); Stevens, Samuel S. (Harriman, TN)

2001-01-01T23:59:59.000Z

319

Well jar incorporating elongate resilient vibration snubbers and mounting apparatus therefor  

Science Conference Proceedings (OSTI)

For use in a well jar, a mounting apparatus for resilient elongate snubbers is described. In the preferred and illustrated embodiment, parallel elongate resilient snubbers are formed on metallic backing strips. They are profiled to define sloping elongate sides which slidably fit within undercut grooves. The undercut grooves extend from an encircling shoulder to enable easy insertion into the grooves. The shoulder is adjacent to an encircling narrow neck, thereby enabling an expandable lock ring to be positioned in the neck, securing the resilient snubbers in position.

Teng, Ch. C.

1985-02-12T23:59:59.000Z

320

The WEI6K, a 6-kW 7-m Small Wind Turbine: Final Technical Report  

SciTech Connect

This project was selected by the U.S. Department of Energy under a DOE solicitation “Low Wind Speed Technology for Small Turbine Development.” The objective of this project has been to design a new small wind turbine with improved cost, reliability and performance in grid-connected residential and small business applications, in order to achieve the overall DOE goal of cost effectiveness in Class 3 wind resources that can now be achieved in Class 5 resources. The scope of work for this project has been to complete the preliminary design of an improved small wind turbine, including preliminary loads and strength analyses; analysis and design of all major components; systems integration and structural dynamic analysis; estimation of life-cycle cost of energy; and design documentation and review. The project did not entail hardware fabrication or testing. The WEI6K Turbine resulting from this project is an upwind horizontal-axis wind turbine rated at 6 kW. It features a 3-blade 7-m diameter rotor. The generator is a direct-drive permanent magnet synchronous machine generating 3-phase power at 240 VAC. The turbine is maintained oriented in to the wind via active yaw control using electromechanical servos. Power is regulated with active blade pitch control. The turbine is presently designed to be placed on a 100-foot (30m) tower. The turbine is predicted to generate electricity at a levelized cost of energy (COE) between 7.3 and 8.9 ¢/kWh at an IEC Class II site, with an average wind speed of 8.5 m/s at hub height, depending upon whether the customer uses a guyed truss tower (the lower figure) or a monopole tower. For the NREL Reference Site, with a mean wind speed of 5.35 m/s at 10 m height, the turbine would generate at a levelized cost of energy of between 9.7 and 11.9 ¢/kWh. The lowest of these numbers is presently competitive with retail electricity rates in most of the country. The 8.9 ¢/kWh is still competitive with retail rates in many regions of the country with high electricity costs. The study further concludes that several design changes could shave 10-14% from the cost of energy determined in the preliminary design. These changes include a new tower design that offers tilt-up capability without guy wires and takes better advantage of the lowered loads produced by pitch control; design a family of airfoils more appropriate for pitch regulation on a turbine of this size; tune the pitch controller properly to minimize shedding of power during turbulent operation in the transition from Region 2 to 3; value engineer the pitch system to shave costs, including consideration of a collective pitch system; and refine the design of the hub and main frame castings to minimize weight and cost. We are generally encouraged by the results. These preliminary numbers show that we can produce a turbine that is competitive with retail electric rates at relatively windy IEC Class II sites. With further improvements in the design, we believe the turbine could be competitive at sites with lesser wind resource.

Wetzel, Kyle K.; McCleer, Patrick J.; Hahlbeck, Edwin C.; DOE Project Office - Keith Bennett

2006-07-21T23:59:59.000Z

Note: This page contains sample records for the topic "kw ground mounted" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Condition Assessment of Substation Ground Grids  

Science Conference Proceedings (OSTI)

This report describes the first stage of research to develop a simple and inexpensive method and device to assess the integrity of substation grounding grids. The problem has been studied before but there is not, to our knowledge, a reliable and inexpensive method or device to make a reliable diagnosis. While the EPRI-developed Ground Grid Evaluator (commercially knows as the Smart Ground Multimeter or SGM) can be used to provide valuable information, the equipment is considered to be expensive and requi...

2008-03-26T23:59:59.000Z

322

Condition Assessment of Substation Ground Grids  

Science Conference Proceedings (OSTI)

This report describes the second stage of a research project to develop a simple and inexpensive method and device to assess the integrity of substation grounding grids. The problem has been studied before but a reliable and inexpensive method or device to make a reliable diagnosis of grid condition is still lacking. While the EPRI-developed Ground Grid Evaluator (commercially known as the Smart Ground Multimeter) can be used to provide valuable information, the equipment is expensive and requires extens...

2008-12-17T23:59:59.000Z

323

Ground Electromagnetic Techniques | Open Energy Information  

Open Energy Info (EERE)

Ground Electromagnetic Techniques Ground Electromagnetic Techniques (Redirected from Ground Electromagnetic Methods) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Technique: Ground Electromagnetic Techniques Details Activities (0) Areas (0) Regions (0) NEPA(0) Exploration Technique Information Exploration Group: Geophysical Techniques Exploration Sub Group: Electrical Techniques Parent Exploration Technique: Electromagnetic Techniques Information Provided by Technique Lithology: Rock composition, mineral and clay content Stratigraphic/Structural: Detection of permeable pathways, fracture zones, faults Hydrological: Resistivity influenced by porosity, grain size distribution, permeability, fluid saturation, fluid type and phase state of the pore water Thermal: Resistivity influenced by temperature

324

Recent ground motion studies at Fermilab  

SciTech Connect

Understanding slow and fast ground motion is important for the successful operation and design for present and future colliders. Since 2000 there have been several studies of ground motion at Fermilab. Several different types of HLS (hydro static level sensors) have been used to study slow ground motion (less than 1 hertz) seismometers have been used for fast (greater than 1 hertz) motions. Data have been taken at the surface and at locations 100 meters below the surface. Data of recent slow ground motion measurements with HLSs, many years of alignment data and results of the ATL-analysis are presented and discussed.

Shiltsev, V.; Volk, J.; /Fermilab; Singatulin, S.; /Novosibirsk, IYF

2009-04-01T23:59:59.000Z

325

Pacific Northwest National Laboratory Grounds Maintenance  

NLE Websites -- All DOE Office Websites (Extended Search)

Pacific Northwest National Laboratory (PNNL) operates an award-winning grounds maintenance program that comprises a comprehensive landscape and irrigation management program. The...

326

US ARMY GROUND VEHICLE HALON REPLACEMENT ...  

Science Conference Proceedings (OSTI)

... test fixture has been constructed from a derelict ground vehicle hull ... exposure levels: ion selective electrodes (grab hag sampling), sorbent tubes ...

2011-10-04T23:59:59.000Z

327

The effect of component efficiency and operating conditions on the 50-kW dish Stirling system in Riyadh, Saudia Arabia  

Science Conference Proceedings (OSTI)

This paper deals with the development of a weather data base and the performance prediction of a 50-kW dish Stirling system. An analysis of direct solar insolation data for 1985 from the site in Riyadh, Saudi Arabia was made to determine the available solar energy. A parameter study was done of the effects of component efficiencies and operating conditions on instantaneous and yearly average system efficiency using the prepared weather data. The system performance was found to be most affected by wind, mirror reflectivity, and exact placement of the receiver in the focal point of the mirror.

Noyes, G.W. (Deutsche Forshungsanstait fur Luft-und Raumfahrt, Inst. fur Technische Thermodynamik, Pfaffenwaldrign 38-40, 7000 Stuttgart 80 (DE))

1990-11-01T23:59:59.000Z

328

Case Study of a 250-kW Molten Carbonate Fuel Cell: LADWP Demonstration of a FuelCell Energy Power Plant: Phase 1  

Science Conference Proceedings (OSTI)

In August 2001, the Los Angeles Department of Water and Power (LADWP) installed a 250-kW pre-commercial molten carbonate fuel cell (MCFC) system manufactured by FuelCell Energy (FCE) at its headquarters building in downtown Los Angeles. At the time, the FCE Direct FuelCell 300A was only the second such system deployed in the United States, although several DFC systems had been deployed in Europe by FCE's partner, MTU. The purpose of the field trial was to gain experience with emerging fuel cell technolog...

2004-03-25T23:59:59.000Z

329

Enclosed ground-flare incinerator  

DOE Patents (OSTI)

An improved ground flare is provided comprising a stack, two or more burner assemblies, and a servicing port so that some of the burner assemblies can be serviced while others remain in operation. The burner assemblies comprise a burner conduit and nozzles which are individually fitted to the stack's burner chamber and are each removably supported in the chamber. Each burner conduit is sealed to and sandwiched between a waste gas inlet port and a matching a closure port on the other side of the stack. The closure port can be opened for physically releasing the burner conduit and supplying sufficient axial movement room for extracting the conduit from the socket, thereby releasing the conduit for hand removal through a servicing port. Preferably, the lower end of the stack is formed of one or more axially displaced lower tubular shells which are concentrically spaced for forming annular inlets for admitting combustion air. An upper tubular exhaust stack, similarly formed, admits additional combustion air for increasing the efficiency of combustion, increasing the flow of exhausted for improved atmospheric dispersion and for cooling the upper stack.

Wiseman, Thomas R. (Calgary, CA)

2000-01-01T23:59:59.000Z

330

Vessel Cold-Ironing Using a Barge Mounted PEM Fuel Cell: Project Scoping and Feasibility  

NLE Websites -- All DOE Office Websites (Extended Search)

3-0501 3-0501 Unlimited Release Printed February 2013 Vessel Cold-Ironing Using a Barge Mounted PEM Fuel Cell: Project Scoping and Feasibility Joseph W. Pratt and Aaron P. Harris Prepared by Sandia National Laboratories Albuquerque, New Mexico 87185 and Livermore, California 94550 Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000. Approved for public release; further dissemination unlimited. 2 Issued by Sandia National Laboratories, operated for the United States Department of Energy by Sandia Corporation. NOTICE: This report was prepared as an account of work sponsored by an agency of the

331

Pyrometer mount for a closed-circuit thermal medium cooled gas turbine  

SciTech Connect

A steam-cooled second-stage nozzle segment has an outer band and an outer cover defining a plenum therebetween for receiving cooling steam for flow through the nozzles to the inner band and cover therefor and return flow through the nozzles. To measure the temperature of the buckets of the stage forwardly of the nozzle stage, a pyrometer boss is electron beam-welded in an opening through the outer band and TIG-welded to the outer cover plate. By machining a hole through the boss and seating a linearly extending tube in the boss, a line of sight between a pyrometer mounted on the turbine frame and the buckets is provided whereby the temperature of the buckets can be ascertained. The welding of the boss to the outer band and outer cover enables steam flow through the plenum without leakage, while providing a line of sight through the outer cover and outer band to measure bucket temperature.

Jones, Raymond Joseph (Duanesburg, NY); Kirkpatrick, Francis Lawrence (late of Galway, NY); Burns, James Lee (Schenectady, NY); Fulton, John Robert (Clifton Park, NY)

2002-01-01T23:59:59.000Z

332

Effects of the Mount Pinatubo eruption on solar insolation: Four case studies  

DOE Green Energy (OSTI)

The Southwest Technology Development Institute staff analyzed solar insolation data from four sites recorded during the years 1990 through 1992. Analyses were performed to identify and quantify the effects on insolation caused by the eruption of Mount Pinatubo in the Philippines on June 15th and 16th, 1991. The four monitoring stations that supplied the raw data for this report were: The Southwest Region Experiment Station in Las Cruces, New Mexico; The Solar Radiation Research Laboratory at the National Renewable Energy Laboratory in Golden, Colorado; The Solar Insolation Monitor Program station operated by the Pacific Gas and Electric Company in Carrisa Plains, California; and The Solar Insolation monitor station at Sandia National Laboratories in Albuquerque, New Mexico. Data from each of the sites were recorded by dedicated datalogging equipment. Every effort was made to prevent data acquisition system problems (e.g., drift of the datalogger clock) from influencing the accuracy of the results.

Rosenthal, A.L.; Robert, J.M. [New Mexico State Univ., Las Cruces, NM (United States). Southwest Technology Development Inst.

1993-05-01T23:59:59.000Z

333

Methane Hydrate Dissociation by Depressurization in a Mount Elbert Sandstone Sample: Experimental Observations and Numerical Simulations  

SciTech Connect

A preserved sample of hydrate-bearing sandstone from the Mount Elbert Test Well was dissociated by depressurization while monitoring the internal temperature of the sample in two locations and the density changes at high spatial resolution using x-ray CT scanning. The sample contained two distinct regions having different porosity and grain size distributions. The hydrate dissociation occurred initially throughout the sample as a result of depressing the pressure below the stability pressure. This initial stage reduced the temperature to the equilibrium point, which was maintained above the ice point. After that, dissociation occurred from the outside in as a result of heat transfer from the controlled temperature bath surrounding the pressure vessel. Numerical modeling of the test using TOUGH+HYDRATE yielded a gas production curve that closely matches the experimentally measured curve.

Kneafsey, T.; Moridis, G.J.

2011-01-15T23:59:59.000Z

334

Design Ground Snow Loads for Ohio  

Science Conference Proceedings (OSTI)

The weight of snow with a mean recurrence interval of 50 years, called the design ground snow load, is used by engineers and planners to estimate the weight of snow that roofs must be designed to support National maps of ground snow load have ...

Thomas W. Schmidlin; Dennis J. Edgell; Molly A. Delaney

1992-06-01T23:59:59.000Z

335

Parameterizing a Groundness Analysis of Logic Programs  

Science Conference Proceedings (OSTI)

We present a parametric groundness analysis whose input and output are parameterized by a set of groundness parameters. The result of the analysis can be instantiated for different uses of the program. It can also be used to derive sufficient conditions ...

Lunjin Lu

2001-07-01T23:59:59.000Z

336

Sharing and groundness dependencies in logic programs  

Science Conference Proceedings (OSTI)

We investigate Jacobs and Langen's Sharing domain, introduced for the analysis of variable sharing in logic programs, and show that it is isomorphic to Marriott and Søndergaard's Pos domain, introduced for the analysis of groundness dependencies. ... Keywords: Boolean functions, abstract interpretation, dataflow analysis, global analysis, groundness analysis, program analysis, sharing analysis

Michael Codish; Harald Søndergaard; Peter J. Stuckey

1999-09-01T23:59:59.000Z

337

A retrospective tiered environmental assessment of the Mount Storm Wind Energy Facility, West Virginia,USA  

SciTech Connect

Bird and bat fatalities from wind energy projects are an environmental and public concern, with post-construction fatalities sometimes differing from predictions. Siting facilities in this context can be a challenge. In March 2012 the U.S. Fish and Wildlife Service (USFWS) released Land-based Wind Energy Guidelines to assess collision fatalities and other potential impacts to species of concern and their habitats to aid in siting and management. The Guidelines recommend a tiered approach for assessing risk to wildlife, including a preliminary site evaluation that may evaluate alternative sites, a site characterization, field studies to document wildlife and habitat and to predict project impacts, post construction studies to estimate impacts, and other post construction studies. We applied the tiered assessment framework to a case study site, the Mount Storm Wind Energy Facility in Grant County, West Virginia, USA, to demonstrate the use of the USFWS assessment approach, to indicate how the use of a tiered assessment framework might have altered outputs of wildlife assessments previously undertaken for the case study site, and to assess benefits of a tiered ecological assessment framework for siting wind energy facilities. The conclusions of this tiered assessment for birds are similar to those of previous environmental assessments for Mount Storm. This assessment found risk to individual migratory tree-roosting bats that was not emphasized in previous preconstruction assessments. Differences compared to previous environmental assessments are more related to knowledge accrued in the past 10 years rather than to the tiered structure of the Guidelines. Benefits of the tiered assessment framework include good communication among stakeholders, clear decision points, a standard assessment trajectory, narrowing the list of species of concern, improving study protocols, promoting consideration of population-level effects, promoting adaptive management through post-construction assessment and mitigation, and sharing information that can be used in other assessments.

Efroymson, Rebecca Ann [ORNL; Day, Robin [No Affiliation; Strickland, M. Dale [Western EcoSystems Technology

2012-11-01T23:59:59.000Z

338

Ground Source Heat Pumps Ground source heat pumps (GSHPs) use the earth's  

E-Print Network (OSTI)

Ground Source Heat Pumps Fact Sheet Ground source heat pumps (GSHPs) use the earth's constant. Waste heat can be used to heat hot water. System Types There are two types of ground source heat pumps, closed loop and open loop systems. Closed loop heat pumps use the earth as the heat source and heat sink

Paulsson, Johan

339

Little Climates -- Weather Just Above The Ground  

NLE Websites -- All DOE Office Websites (Extended Search)

Weather Just Above The Ground Weather Just Above The Ground Nature Bulletin No. 481-A February 17, 1973 Forest Preserve District of Cook County George W, Dunne, President Roland F. Eisenbeis, Supt. of Conservation LITTLE CLIMATES -- Weather Just Above the Ground In a previous bulletin we talked about little climates, underground, resulting from weather conditions in the soil. Just above the ground there is another "little climate" equally important. We frequently see evidences of it without realizing how and why they were produced. Just above the earth, there lies a narrow layer of changeable weather that is affected at both surfaces by its mighty neighbors: the land below and the restless air in the atmosphere above it. Under the spell of gravity, it clings to the ground in spite of all but the swiftest winds. In this layer there are special weather conditions overlooked by nearly everyone.

340

Ground Source Heat Pumps | Open Energy Information  

Open Energy Info (EERE)

Ground Source Heat Pumps Ground Source Heat Pumps (Redirected from Geothermal Heat Pumps) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Print PDF Ground Source Heat Pumps Geothermal Technologies There are many types of Geothermal Technologies that take advantage of the earth's heat: Hydrothermal Systems Enhanced Geothermal Systems (EGS) Sedimentary Geothermal Systems Co-Produced Geothermal Systems Geothermal Direct Use Ground Source Heat Pumps GSHP Links Related documents and websites An Information Survival Kit for the Prospective Geothemral Heat Pump Owner List of Heat Pumps Incentives List of Ground Source Heat Pumps Incentives Policy Makers' Guidebook for Geothermal Heating and Cooling Various ways to configure a geothermal heat pump system. (Source: The Geo-Heat Center's Survival Kit for the Prospective Geothemral Heat Pump

Note: This page contains sample records for the topic "kw ground mounted" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Ground Source Heat Pumps | Open Energy Information  

Open Energy Info (EERE)

Ground Source Heat Pumps Ground Source Heat Pumps Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Print PDF Ground Source Heat Pumps Geothermal Technologies There are many types of Geothermal Technologies that take advantage of the earth's heat: Hydrothermal Systems Enhanced Geothermal Systems (EGS) Sedimentary Geothermal Systems Co-Produced Geothermal Systems Geothermal Direct Use Ground Source Heat Pumps GSHP Links Related documents and websites An Information Survival Kit for the Prospective Geothemral Heat Pump Owner List of Heat Pumps Incentives List of Ground Source Heat Pumps Incentives Policy Makers' Guidebook for Geothermal Heating and Cooling Various ways to configure a geothermal heat pump system. (Source: The Geo-Heat Center's Survival Kit for the Prospective Geothemral Heat Pump

342

Self-potential methods on geothermal exploration: case study: Mount Patuha, west Java, Indonesia  

Science Conference Proceedings (OSTI)

The purpose of this study is to interpret self-potential data by analyzing of the curve shape, contour, and positive-negative value of self potential polarization anomalies. The results are used to estimate the direction of fluid movement in subsurface ... Keywords: curve shape, geothermal energy, ground water, self potential polarization anomalies

Alamta Singarimbun; Mitra Djamal; Fitri Meilawati

2011-07-01T23:59:59.000Z

343

z'-BAND GROUND-BASED DETECTION OF THE SECONDARY ECLIPSE OF WASP-19b  

Science Conference Proceedings (OSTI)

We present the ground-based detection of the secondary eclipse of the transiting exoplanet WASP-19b. The observations were made in the Sloan z' band using the ULTRACAM triple-beam CCD camera mounted on the New Technology Telescope. The measurement shows a 0.088% {+-} 0.019% eclipse depth, matching previous predictions based on H- and K-band measurements. We discuss in detail our approach to the removal of errors arising due to systematics in the data set, in addition to fitting a model transit to our data. This fit returns an eclipse center, T{sub 0}, of 2455578.7676 HJD, consistent with a circular orbit. Our measurement of the secondary eclipse depth is also compared to model atmospheres of WASP-19b and is found to be consistent with previous measurements at longer wavelengths for the model atmospheres we investigated.

Burton, J. R.; Watson, C. A.; Pollacco, D. [Astrophysics Research Centre, Queen's University Belfast, Belfast BT7 1NN (United Kingdom); Littlefair, S. P.; Dhillon, V. S. [Department of Physics and Astronomy, University of Sheffield, Sheffield S3 7RH (United Kingdom); Gibson, N. P. [Department of Physics, University of Oxford, Oxford OX1 3RH (United Kingdom); Marsh, T. R., E-mail: jburton04@qub.ac.uk [Department of Physics and Astronomy, University of Warwick, Coventry CV4 7AL (United Kingdom)

2012-08-01T23:59:59.000Z

344

40 kW of solar cell modules for the Large Scale Production Task, a Low Cost Silicon Solar Array Project. Final technical report  

SciTech Connect

Forty kilowatts of solar cell modules was produced in this program. This is equivalent to 4123 modules. The average power output per module was 9.7 watts at 16.5 volts, 60/sup 0/C and 100 mW/cm/sup 2/. The peak production rate was 200 modules per week which is equal to 1.9 kW per week. This rate was sustained for over four and one-half months and is equivalent to 100 kW per year. The solar cell module design, electrical and power performance, module preproduction environmental test results, production and shipping schedule, program summary, and delivery are described. A cost analysis section is written. Particular emphasis on the percentage of labor and material utilized in constructing a solar cell module is presented. Also included are cost reduction recommendations. It was concluded from this program that volume production on the order of hundreds of kilowatts per year per company as a minimum is required to significantly reduce the price per watt for solar cell modules. Sensor Technology more than doubled its solar cell module manufacturing facilities since the completion of the JPL Block II procurement. Plans are being made for large scale expansion of our facilities to meet growing JPL/DOE procurements.

Jones, G.T.

1977-12-01T23:59:59.000Z

345

Post-test analysis of 20kW molten carbonate fuel cell stack operated on coal gas. Final report, August 1993--February 1996  

DOE Green Energy (OSTI)

A 20kW carbonate fuel cell stack was operated with coal gas for the first time in the world. The stack was tested for a total of 4,000 hours, of which 3,900 hours of testing was conducted at the Louisiana Gasification Technology Incorporated, Plaquemine, Louisiana outdoor site. The operation was on either natural gas or coal gas and switched several times without any effects, demonstrating duel fuel capabilities. This test was conducted with 9142 kJ/m{sup 3} (245 Btu/cft) coal gas provided by a slipstream from Destec`s entrained flow, slagging, slurry-fed gasifier equipped with a cold gas cleanup subsystem. The stack generated up to 21 kW with this coal gas. Following completion of this test, the stack was brought to Energy Research Corporation (ERC) and a detailed post-test analysis was conducted to identify any effects of coal gas on cell components. This investigation has shown that the direct fuel cell (DFC) can be operated with properly cleaned and humidified coal-as, providing stable performance. The basic C direct fuel cell component materials are stable and display normal stability in presence of the coal gas. No effects of the coal-borne contaminants are apparent. Further cell testing at ERC 1 17, confirmed these findings.

NONE

1996-05-01T23:59:59.000Z

346

Materials Reliability Program: Inspection and Evaluation Guidelines for Reactor Vessel Bottom-Mounted Nozzles in U.S. PWR Plants (MR P-206)  

Science Conference Proceedings (OSTI)

This report presents inspection and evaluation guidelines for reactor vessel bottom-mounted nozzles in U.S. pressurized water reactor (PWR) plants.

2009-03-23T23:59:59.000Z

347

Definition: Ground Electromagnetic Techniques | Open Energy Information  

Open Energy Info (EERE)

Definition Definition Edit with form History Facebook icon Twitter icon » Definition: Ground Electromagnetic Techniques Jump to: navigation, search Dictionary.png Ground Electromagnetic Techniques Ground electromagnetic techniques measure electromagnetic fields in order to determine subsurface electrical resistivity with the earth surface as the observation point.[1] View on Wikipedia Wikipedia Definition The electromagnetic force is one of the four fundamental interactions in nature, the other three being the strong interaction, the weak interaction, and gravitation. This force is described by electromagnetic fields, and has innumerable physical instances including the interaction of electrically charged particles and the interaction of uncharged magnetic force fields with electrical conductors. The word

348

Ground Electromagnetic Techniques | Open Energy Information  

Open Energy Info (EERE)

Ground Electromagnetic Techniques Ground Electromagnetic Techniques Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Technique: Ground Electromagnetic Techniques Details Activities (0) Areas (0) Regions (0) NEPA(0) Exploration Technique Information Exploration Group: Geophysical Techniques Exploration Sub Group: Electrical Techniques Parent Exploration Technique: Electromagnetic Techniques Information Provided by Technique Lithology: Rock composition, mineral and clay content Stratigraphic/Structural: Detection of permeable pathways, fracture zones, faults Hydrological: Resistivity influenced by porosity, grain size distribution, permeability, fluid saturation, fluid type and phase state of the pore water Thermal: Resistivity influenced by temperature Dictionary.png

349

Volcanic Ash Transport from Mount Asama to the Tokyo Metropolitan Area Influenced by Large-Scale Local Wind Circulation  

Science Conference Proceedings (OSTI)

The eruption of the Mount Asama volcano on 16 September 2004 produced an ash cloud and led to ashfall in the Tokyo metropolitan area that lies on the Kanto Plain. Satellite images showed the ash cloud drifting toward the south in the morning but ...

Nobumitsu Tsunematsu; Tomohiro Nagai; Toshiyuki Murayama; Ahoro Adachi; Yasuhiro Murayama

2008-04-01T23:59:59.000Z

350

Grounded Renewable Energy | Open Energy Information  

Open Energy Info (EERE)

Grounded Renewable Energy Grounded Renewable Energy Jump to: navigation, search Name Grounded Renewable Energy Place Carbondale, Colorado Zip 81623 Sector Renewable Energy, Solar Product Grounded Renewable Energy designs turn-key solar systems for homes and businesses in Colorado. Coordinates 41.573959°, -75.501361° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":41.573959,"lon":-75.501361,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

351

Earthquake ground motion modeling on parallel computers  

Science Conference Proceedings (OSTI)

We describe the design and discuss the performance of a parallel elastic wave propagation simulator that is being used to model and study earthquake-induced ground motion in large sedimentary basins. The components of the system include mesh generators, ...

Hesheng Bao; Jacobo Bielak; Omar Ghattas; Loukas F. Kallivokas; David R. O'Hallaron; Jonathan R. Shewchuk; Jifeng Xu

1996-11-01T23:59:59.000Z

352

Solid waste burial grounds interim safety analysis  

SciTech Connect

This Interim Safety Analysis document supports the authorization basis for the interim operation and restrictions on interim operations for the near-surface land disposal of solid waste in the Solid Waste Burial Grounds. The Solid Waste Burial Grounds Interim Safety Basis supports the upgrade progress for the safety analysis report and the technical safety requirements for the operations in the Solid Waste Burial Grounds. Accident safety analysis scenarios have been analyzed based on the significant events identified in the preliminary hazards analysis. The interim safety analysis provides an evaluation of the operations in the Solid Waste Burial Grounds to determine if the radiological and hazardous material exposures will be acceptable from an overall health and safety standpoint to the worker, the onsite personnel, the public, and the environment.

Saito, G.H.

1994-10-01T23:59:59.000Z

353

Embodied object schemas for grounding language use  

E-Print Network (OSTI)

This thesis presents the Object Schema Model (OSM) for grounded language interaction. Dynamic representations of objects are used as the central point of coordination between actions, sensations, planning, and language ...

Hsiao, Kai-yuh, 1977-

2007-01-01T23:59:59.000Z

354

Grounding linguistic analysis in control applications  

E-Print Network (OSTI)

This thesis addresses the problem of grounding linguistic analysis in control applications, such as automated maintenance of computers and game playing. We assume access to natural language documents that describe the ...

Branavan, Satchuthananthavale Rasiah Kuhan

2012-01-01T23:59:59.000Z

355

Ground Clutter Canceling with a Regression Filter  

Science Conference Proceedings (OSTI)

This paper explores ground clutter filtering with a class of cancelers that use regression. Regression filters perform this task in a simple manner, resulting in similar or better performance than the fifth-order elliptic filter implemented in ...

Sebastián M. Torres; Dusan S. Zrnic

1999-10-01T23:59:59.000Z

356

Commonality of ground systems in launch operations  

E-Print Network (OSTI)

NASA is examining the utility of requiring a certain degree of commonality in both flight and ground systems in the Constellation Program. While the benefits of commonality seem obvious in terms of minimizing upfront ...

Quinn, Shawn M

2008-01-01T23:59:59.000Z

357

Ground Penetrating Imaging Radar Phase II  

Science Conference Proceedings (OSTI)

EPRI project "Ground Penetrating Imaging Radar Phase II," also called the "GPiR Project," started in August 1998 at Schlumberger-Doll Research, a division of Schlumberger Technology Corporation. Its goal was to determine if modern ground-penetrating radar (GPR) could make three-dimensional (3D) images of buried utility lines accurate and detailed enough to help utility companies better manage their underground infrastructure. Work began with a comparison of commercial and prototype GPR systems in the lab...

2001-06-20T23:59:59.000Z

358

Design, Fabrication, and Test of a 5-kWh/100-kW Flywheel Energy Storage Utilizing a High-Temperature Superconducting Bearing  

DOE Green Energy (OSTI)

The summaries of this project are: (1) Program goal is to design, develop, and demonstrate a 100 kW UPS flywheel electricity system; (2) flywheel system spin tested up to 15,000 RPM in a sensorless, closed loop mode; (3) testing identified a manufacturing deficiency in the motor stator--overheats at high speed, limiting maximum power capability; (4) successfully spin tested direct cooled HTS bearing up to 14,500 RPM (limited by Eddy current clutch set-up); (5) Testing confirmed commercial feasibility of this bearing design--Eddy Current losses are within acceptable limits; and (6) Boeing's investment in flywheel test facilities increased the spin-test capabilities to one of the highest in the nation.

Dr. Michael Strasik, Philip E Johnson; A. C. Day; J. Mittleider; M. D. Higgins; J. Edwards; J. R. Schindler; K. E. McCrary; C.R. McIver; D.; J. F. Gonder; J. R. Hull

2007-10-29T23:59:59.000Z

359

Development of a low cost integrated 15 kW A.C. solar tracking sub-array for grid connected PV power system applications  

SciTech Connect

Utility Power Group has achieved a significant reduction in the installed cost of grid-connected PV systems. The two part technical approach focused on (1) The utilization of a large area factory assembled PV panel, and (2) The integration and packaging of all sub-array power conversion and control functions within a single factory produced enclosure. Eight engineering prototype 15kW ac single axis solar tracking sub-arrays were designed, fabricated, and installed at the Sacramento Municipal Utility District{close_quote}s Hedge Substation site in 1996 and are being evaluated for performance and reliability. A number of design enhancements will be implemented in 1997 and demonstrated by the field deployment and operation of over twenty advanced sub-array PV power systems. {copyright} {ital 1997 American Institute of Physics.}

Stern, M.; West, R.; Fourer, G.; Whalen, W.; Van Loo, M.; Duran, G. [Utility Power Group, 9410 G De Soto Avenue, Chatsworth, California 91311 (United States)

1997-02-01T23:59:59.000Z

360

Development of a Low-Cost 3-10 kW Tubular SOFC Power System - DOE Hydrogen and Fuel Cells Program FY 2012 Annual Progress Report  

NLE Websites -- All DOE Office Websites (Extended Search)

7 7 FY 2012 Annual Progress Report DOE Hydrogen and Fuel Cells Program Norman Bessette Acumentrics Corporation 20 Southwest Park Westwood, MA 02090 Phone: (781) 461-8251; Email: nbessette@acumentrics.com DOE Managers HQ: Dimitrios Papageorgopoulos Phone: (202) 586-5463 Email: Dimitrios.Papageorgopoulos@ee.doe.gov GO: Reginald Tyler Phone: (720) 356-1805 Email: Reginald.Tyler@go.doe.gov Contract Number: DE-FC36-03NT41838 Project Start Date: April 1, 2008 Project End Date: March 31, 2013 Fiscal Year (FY) 2012 Objectives The goal of the project is to develop a low-cost 3-10 kW solid oxide fuel cell (SOFC) power generator capable of meeting multiple market applications. This is accomplished by: Improving cell power and stability * Cost reduction of cell manufacturing

Note: This page contains sample records for the topic "kw ground mounted" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Development of an 8 kW wind turbine generator for residential type applications. Phase I: design and analysis. Volume II. Technical report  

SciTech Connect

This Phase I summary report contains a description of the 8 kW wind energy conversion system developed by the United Technologies Research Center (UTRC) for the Department of Energy. The wind turbine employs the UTRC Bearingless Rotor Concept in conjunction with a passive pendulum control system which controls blade pitch for start-up, efficient power generation, and high-speed survivability. The report contains a summary of the experimental and analytical programs in support of design efforts. These supporting programs include materials tests, a wind tunnel program, and aeroelastic analyses to evaluate system stability. An estimate is also made of the projected manufacturing cost of the system if produced in quantity.

Cheney, M.C.

1979-06-25T23:59:59.000Z

362

Ground water protection management program plan  

SciTech Connect

U.S. Department of Energy (DOE) Order 5400.1 requires the establishment of a ground water protection management program to ensure compliance with DOE requirements and applicable federal, state, and local laws and regulations. The Uranium Mill Tailings Remedial Action (UMTRA) Project Office was prepared this Ground Water Protection Management Program Plan (ground water protection plan) whose scope and detail reflect the program`s significance and address the seven activities required in DOE Order 5400.1, Chapter III, for special program planning. This ground water protection plan highlights the methods designed to preserve, protect, and monitor ground water resources at UMTRA Project processing and disposal sites. The plan includes an overview of the remedial action status at the 24 designated processing sites and identifies technical guidance documents and site-specific documents for the UMTRA Project ground water protection management program. In addition, the plan addresses the general information required to develop a water resources protection strategy at the permanent disposal sites. Finally, the plan describes ongoing activities that are in various stages of development at UMTRA Project sites.

Not Available

1994-02-01T23:59:59.000Z

363

Slit-mounted LED fiducial system for rotating mirror streak cameras  

SciTech Connect

We have developed a fiducial system for rotating mirror streak cameras that utilizes light emitting diodes mounted at the slit position of the camera. The diodes are driven to the required high brightness by a unique pulse power circuit designed to provide high voltage, high current pulses 18 nanoseconds in length at a frequency of up to 2.5 megahertz. The availability of super bright light emitting diodes with a wavelength of 630 to 640 nanometers allows us to record fiducial pulses, at streaking speeds in excess of 20mm per microsecond, on all the black and white films commonly used in high speed photography. The time marks on the film record are referenced to the real time of the experiment from a clock-driver that controls the start and frequency of the fiducial pulse train and by three adjustable and discreet blanked fiducials. This paper discusses the development of this system and describes the full setup as used at LLNL. 6 refs., 4 figs.

Shaw, L.L.; Muelder, S.A.; Rivera, A.T.

1991-01-01T23:59:59.000Z

364

Grounding Analysis in Heterogeneous Soil Models: Application to Underground Substations  

E-Print Network (OSTI)

Grounding Analysis in Heterogeneous Soil Models: Application to Underground Substations Ignasi in forthcoming publications. Keywords-grounding analysis; earthing analysis, underground substations; I to a river (at substations next to hydroelectric dams), or the grounding system of a buried electrical

Colominas, Ignasi

365

Ground-coupled heat pump systems: a pumping analysis.  

E-Print Network (OSTI)

??Ground-coupled heat pump (GCHP) systems use the ground as a heat source or sink that absorbs heat from or rejects heat to the soil, respectively;… (more)

Mays, Cristin Jean

2012-01-01T23:59:59.000Z

366

Montana Ground Water Assessment Act (Montana) | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Ground Water Assessment Act (Montana) Montana Ground Water Assessment Act (Montana) Eligibility Utility Fed. Government Commercial Agricultural Investor-Owned Utility State...

367

Ground Gravity Survey At Marysville Mt Area (Blackwell) | Open...  

Open Energy Info (EERE)

Ground Gravity Survey At Marysville Mt Area (Blackwell) Exploration Activity Details Location Marysville Mt Area Exploration Technique Ground Gravity Survey Activity Date...

368

Designated Ground Water Basin Map | Open Energy Information  

Open Energy Info (EERE)

Designated Ground Water Basin Map Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Reference Material: Designated Ground Water Basin Map Details Activities (0) Areas...

369

Deputy Secretary Poneman Attends Ground Breaking at Tennessee...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Home Deputy Secretary Poneman Attends Ground Breaking at Tennessee Advanced Vehicle Battery Plant Deputy Secretary Poneman Attends Ground Breaking at Tennessee Advanced Vehicle...

370

Recovery Act - Geothermal Technologies Program:Ground Source...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Recovery Act - Geothermal Technologies Program:Ground Source Heat Pumps Recovery Act - Geothermal Technologies Program:Ground Source Heat Pumps A detailled description of the...

371

EA-1406: Ground Water Compliance at the New Rifle, Colorado,...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

6: Ground Water Compliance at the New Rifle, Colorado, UMTRA Project Site, Rifle, Colorado EA-1406: Ground Water Compliance at the New Rifle, Colorado, UMTRA Project Site, Rifle,...

372

Ground Gravity Survey At Mcgee Mountain Area (DOE GTP) | Open...  

Open Energy Info (EERE)

Ground Gravity Survey At Mcgee Mountain Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Ground Gravity Survey At Mcgee Mountain...

373

Water Quality Surface and Ground | Open Energy Information  

Open Energy Info (EERE)

Quality Surface and Ground Jump to: navigation, search Retrieved from "http:en.openei.orgwindex.php?titleWaterQualitySurfaceandGround&oldid612197...

374

GROUND PLANE INSULATION FAILURE IN THE FIRST TPC SUPERCONDUCTING COIL  

E-Print Network (OSTI)

is WIUUTEO GROUND PLANE INSULATION FAILURE IN THE FIRST TPCOn August 27, 1980, an insulation failure occurred dt-ringby a failure uf ground plane insulation. ACKNOWLEDGMENTS The

Green, M.A.

2010-01-01T23:59:59.000Z

375

Vertical Distribution of Contamination in Ground Water at the...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Vertical Distribution of Contamination in Ground Water at the Tuba City, Arizona, Site Vertical Distribution of Contamination in Ground Water at the Tuba City, Arizona, Site...

376

Longevity of Emplacement Drift Ground Support Materials  

SciTech Connect

The purpose of this analysis is to evaluate the factors affecting the longevity of emplacement drift ground support materials and to develop a basis for selection of materials for ground support that will function throughout the preclosure period. The Development Plan (DP) for this analysis is given in CRWMS M&O (Civilian Radioactive Waste Management System Management and Operating Contractor) (1999a). The candidate materials for ground support are steel (carbon steel, ductile cast iron, galvanized steel, and stainless steel, etc.) and cement. Steel will mainly be used for steel sets, lagging, channels, rock bolts, and wire mesh. Cement usage is only considered in the case of grouted rock bolts. The candidate materials for the invert structure are steel and crushed rock ballast. The materials shall be evaluated for the repository emplacement drift environment under a specific thermal loading condition based on the proposed License Application Design Selection (LADS) design. The analysis consists of the following tasks: (1) Identify factors affecting the longevity of ground control materials for use in emplacement drifts. (2) Review existing documents concerning behavior of candidate ground control materials during the preclosure period. The major criteria to be considered for steel are mechanical and thermal properties, and durability, of which corrosion is the most important concern. (3) Evaluate the available results and develop recommendations for material(s) to be used.

D. Tang

2000-01-07T23:59:59.000Z

377

An Analysis of a Spreader Bar Crane Mounted Gamma-Ray Radiation Detection System  

E-Print Network (OSTI)

Over 95% of imports entering the United States from outside North America arrive via cargo containers by sea at 329 ports of entry. The current layered approach for the detection only scans 5% of cargo bound for the United States. This is inadequate to protect our country. This research involved the building of a gamma-ray radiation detection system used for cargo scanning. The system was mounted on a spreader bar crane (SBC) at the Port of Tacoma (PoT) and the applicability and capabilities of the system were analyzed. The detection system provided continuous count rate and spectroscopic data among three detectors while operating in an extreme environment. In a separate set of experiments, 60Co and 137Cs sources were positioned inside a cargo container and data were recorded for several count times. The Monte Carlo N-Particle (MCNP) code was used to simulate a radioactive source inside an empty cargo container and the results were compared to experimentally recorded data. The detection system demonstrated the ability to detect 60Co, 137Cs, 192Ir, highly-enriched uranium (HEU), and weapons-grade plutonium (WGPu) with minimum detectable activities (MDA) of 5.9 ± 0.4 microcuries (?Ci), 19.3 ± 1.1 ?Ci, 11.7 ± 0.6 ?Ci, 3.5 ± 0.3 kilograms (kg), and 30.6 ± 1.3 grams (g), respectively. This system proved strong gamma-ray detection capabilities, but was limited in the detection of fissile materials Additional details of this system are presented and advantages of this approach to cargo scanning over current approaches are discussed.

Grypp, Matthew D

2013-05-01T23:59:59.000Z

378

Control of Surface Mounted Permanent Magnet Motors with Special Application to Fractional-Slot Concentrated Windings  

SciTech Connect

It is well known that the ability of the permanent magnet synchronous machine (PMSM) to operate over a wide constant power speed range (CPSR) is dependent upon the machine inductance [1,2,3,4,5]. Early approaches for extending CPSR operation included adding supplementary inductance in series with the motor [1] and the use of anti-parallel thyristor pairs in series with the motor-phase windings [5]. The increased inductance method is compatible with a voltage-source inverter (VSI) controlled by pulse-width modulation (PWM) which is called the conventional phase advance (CPA) method. The thyristor method has been called the dual mode inverter control (DMIC). Neither of these techniques has met with wide acceptance since they both add cost to the drive system and have not been shown to have an attractive cost/benefit ratio. Recently a method has been developed to use fractional-slot concentrated windings to significantly increase the machine inductance [6]. This latest approach has the potential to make the PMSM compatible with CPA without supplemental external inductance. If the performance of such drive is acceptable, then the method may make the PMSM an attractive option for traction applications requiring a wide CPSR. A 30 pole, 6 kW, 6000 maximum revolutions per minute (rpm) prototype of the fractional-slot PMSM design has been developed [7]. This machine has significantly more inductance than is typical of regular PMSMs. The prototype is to be delivered in late 2005 to the Oak Ridge National Laboratory (ORNL) for testing and development of a suitable controller. In advance of the test/control development effort, ORNL has used the PMSM models developed over a number of previous studies to study the steady-state performance of high-inductance PMSM machines with a view towards control issues. The detailed steady-state model developed includes all motor and inverter-loss mechanisms and will be useful in assessing the performance of the dynamic controller to be developed in future work. This report documents the results of this preliminary investigation.

Lawler, J.S.

2005-12-21T23:59:59.000Z

379

Computationally Efficient Methods of Collocating Satellite, Aircraft, and Ground Observations  

Science Conference Proceedings (OSTI)

The usefulness of measurements from satellite-borne instruments is enhanced if these measurements can be compared to measurements from other instruments mounted aboard the same or different satellite, with measurements from aircraft, or with ...

Frederick W. Nagle; Robert E. Holz

2009-08-01T23:59:59.000Z

380

Appendix B Ground Water Management Policy  

Office of Legacy Management (LM)

Ground Water Management Policy Ground Water Management Policy for the Monticello Mill Tailings Site and Adjacent Areas This page intentionally left blank Docun~ent Number Q0029500 Appendix B State of Utah DEPARTblENT OF NATURAL RESOURCES DIVISION OF WATER RIGHTS Ground-Water Management Policy for the Mot~ticello Mill Tailings Site and Adjacent Areas The Monticello Mill Tailings Site is on the southeast portion of the tovm of Monticello in Sectton 36, T33S, K23E and Section 31, i33S. R24E, SLB&M. The mill site was used from 1942 to 1960 in the processing of uranium and vanadium. The U.S. Department of Energy (DOE) is currently cleaning up the site. The site is in the small canyon that forms the drainage for South Creek. The general direction of water flow, of both surface streams and the shallow

Note: This page contains sample records for the topic "kw ground mounted" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Definition: Ground Gravity Survey | Open Energy Information  

Open Energy Info (EERE)

Definition Definition Edit with form History Facebook icon Twitter icon » Definition: Ground Gravity Survey Jump to: navigation, search Dictionary.png Ground Gravity Survey The ground gravitational method is the study of the distribution of mass in the subsurface with the observation point at the earth's surface.[1] View on Wikipedia Wikipedia Definition A gravity anomaly is the difference between the observed acceleration of a planet's gravity and a value predicted from a model. A location with a positive anomaly exhibits more gravity than predicted, while a negative anomaly exhibits a lower value than predicted. References ↑ http://www.amazon.com/Geophysical-Field-Theory-Three-Volume-Gravitational/dp/0124020410 Ret Like Like You like this.Sign Up to see what your friends like.

382

GroundedPower Inc | Open Energy Information  

Open Energy Info (EERE)

GroundedPower Inc GroundedPower Inc Jump to: navigation, search Name GroundedPower Inc Place Gloucester, Massachusetts Zip 1930 Product Massachusetts-based company developing home and building energy management systems via IP-based software. Coordinates 37.413962°, -76.526305° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":37.413962,"lon":-76.526305,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

383

Ground Gravity Survey | Open Energy Information  

Open Energy Info (EERE)

Ground Gravity Survey Ground Gravity Survey Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Technique: Ground Gravity Survey Details Activities (48) Areas (34) Regions (2) NEPA(2) Exploration Technique Information Exploration Group: Geophysical Techniques Exploration Sub Group: Gravity Techniques Parent Exploration Technique: Gravity Techniques Information Provided by Technique Lithology: Distribution of density in the subsurface enables inference of rock type. Stratigraphic/Structural: Delineation of steeply dipping formations, geological discontinuities and faults, intrusions and large-scale deposition of silicates due to hydrothermal activity. Hydrological: Density of sedimentary rocks are strongly influenced by fluid contained within pore space. Dry bulk density refers to the rock with no moisture, while the wet bulk density accounts for water saturation; fluid content may alter density by up to 30%.(Sharma, 1997)

384

2012 CERTS R&M Peer Review - Evaluating the Effects of Managing Controllable Demand - Tim Mount  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Evaluating the Effects of Managing Evaluating the Effects of Managing Controllable Demand and Distributed Energy Resources Locally on System Performance and Costs Tim Mount and Ray Zimmerman Dyson School of Applied Economics and Management Cornell University Alejandro Dominguez-Garcia Department of Electrical and Computer Engineering University of Illinois, Urbana-Champaign CERTS Review, Cornell, August 7-8, 2012 An NSF I/UCRC Collaborative Research on the Smart Grid PSERC Researchers at Cornell Engineers Economists Lindsay Anderson Wooyoung Jeon* Hsiao-Dong Chiang Alberto Lamadrid* Andrew Hunter Jung Youn Mo* Bob Thomas Surin Maneevitjit* Lang Tong Tim Mount Max Zhang Dick Schuler Ray Zimmerman Bill Schulze + Hao Lu* Judy Cardell, Smith College +

385

Water budget for SRP burial ground area  

SciTech Connect

Radionuclide migration from the SRP burial ground for solid low-level waste has been studied extensively. Most of the buried radionuclides are fixed on the soil and show negligible movement. The major exception is tritium, which when leached from the waste by percolating rainfall, forms tritiated water and moves with the groundwater. The presence of tritium has been useful in tracing groundwater flow paths to outcrop. A subsurface tritium plume moving from the southwest corner of the burial ground toward an outcrop near Four Mile Creek has been defined. Groundwater movement is so slow that much of the tritium decays before reaching the outcrop. The burial ground tritium plume defined to date is virtually all in the uppermost sediment layer, the Barnwell Formation. The purpose of the study reported in this memorandum was to investigate the hypothesis that deeper flow paths, capable of carrying substantial amounts of tritium, may exist in the vicinity of the burial ground. As a first step in seeking deeper flow paths, a water budget was constructed for the burial ground site. The water budget, a materials balance used by hydrologists, is expressed in annual area inches of rainfall. Components of the water budget for the burial ground area were analyzed to determine whether significant flow paths may exist below the tan clay. Mean annual precipitation was estimated as 47 inches, with evapotranspiration, run-off, and groundwater recharge estimated as 30, 2, and 15 inches, respectively. These estimates, when combined with groundwater discharge data, suggest that 5 inches of the groundwater recharge flow above the tan clay and that 10 inches flow below the tan clay. Therefore, two-thirds of the groundwater recharge appears to follow flow paths that are deeper than those previously found. 13 references, 10 figures, 5 tables.

Hubbard, J.E.; Emslie, R.H.

1984-03-19T23:59:59.000Z

386

Multisensor Fusion of Ground-based and Airborne Remote Sensing Data for Crop Condition Assessment  

E-Print Network (OSTI)

In this study, the performances of the optical sensors and instruments carried on both ground-based and airborne platforms were evaluated for monitoring crop growing status, detecting the vegetation response to aerial applied herbicides, and identifying crop nitrogen status. Geostatistical analysis on remotely sensed data was conducted to investigate spatial structure of crop canopy normalized difference vegetation index and multispectral imagery. A computerized crop monitoring system was developed that combined sensors and instruments that measured crop structure and spectral data with a global positioning system. The integrated crop monitoring system was able to collect real-time, multi-source, multi-form, and crop related data simultaneously as the tractor-mounted system moved through the field. This study firstly used remotely sensed data to evaluate glyphosate efficacy on weeds applied with conventional and emerging aerial spray nozzles. A weedy field was In this study, the performances of the optical sensors and instruments carried on both ground-based and airborne platforms were evaluated for monitoring crop growing status, detecting the vegetation response to aerial applied herbicides, and identifying crop nitrogen status. Geostatistical analysis on remotely sensed data was conducted to investigate spatial structure of crop canopy normalized difference vegetation index and multispectral imagery. A computerized crop monitoring system was developed that combined sensors and instruments that measured crop structure and spectral data with a global positioning system. The integrated crop monitoring system was able to collect real-time, multi-source, multi-form, and crop related data simultaneously as the tractor-mounted system moved through the field. This study firstly used remotely sensed data to evaluate glyphosate efficacy on weeds applied with conventional and emerging aerial spray nozzles. A weedy field was set up in three blocks and four aerial spray technology treatments were tested. Spectral reflectance measurements were taken using ground-based sensors from all the plots at 1, 8, and 17 days after treatment. The results indicated that the differences among the treatments could be detected with spectral data. This study could provide applicators with guidance equipment configurations that can result in herbicide savings and optimized applications in other crops. The main focus of this research was to apply sensor fusion technology to ground-based and airborne imagery data. Experimental plots cropped with cotton and soybean plants were set up with different nitrogen application rates. The multispectral imagery was acquired by an airborne imaging system over crop field; at the same period, leaf chlorophyll content and spectral reflectance measurements were gathered with chlorophyll meter and spectroradiometer at canopy level on the ground, respectively. Statistical analyses were applied on the data from individual sensor for discrimination with respect to the nitrogen treatment levels. Multisensor data fusion was performed at data level. The results showed that the data fusion of airborne imagery with ground-based data were capable of improving the performance of remote sensing data on detection of crop nitrogen status. The method may be extended to other types of data, and data fusion can be performed at feature or decision level.

Zhang, Huihui

2010-12-01T23:59:59.000Z

387

Ground-Based Microwave Radiometer Measurements  

NLE Websites -- All DOE Office Websites (Extended Search)

Ground-Based Microwave Radiometer Measurements Ground-Based Microwave Radiometer Measurements and Radiosonde Comparisons During the WVIOP2000 Field Experiment D. Cimini University of L'Aquila L'Aquil, Italy E. R. Westwater Cooperative Institute for Research in the Environmental Sciences University of Colorado National Oceanic and Atmospheric Administration Environmental Technology Laboratory Boulder, Colorado Y. Han Science System Applications National Aeronautics Space Administration Goddard Space Flight Center Greenbelt, Maryland S. Keihm Jet Propulsion Laboratory California Institute of Technology Pasadena, California Introduction During September to October 2000, a water vapor intensive operational period (WVIOP) was conducted at the Atmospheric Radiation Measurement (ARM) Program's Southern Great Plains (SGP) Cloud and

388

Study of Support Amplification Factors for Various Frequency and Mass Ratios of Idealized Equipment Mounted on a Support Structure  

Science Conference Proceedings (OSTI)

This project studied the dynamic amplification factor of a support structure for various equipment–to–support mass and frequency ratios for cases in which utility substation equipment is mounted on a support structure and subject to IEEE standard 693, IEEE Recommended Practice for Seismic Design of Substations. The project is one of several sponsored by the Electric Power Research Institute (EPRI) Seismic Working Group, which was organized to conduct tests at appropriate ...

2013-06-26T23:59:59.000Z

389

Subsurface Characterization at Ground Failure Sites in Adapazari, Turkey  

E-Print Network (OSTI)

ground failure. Lastly, ?ve CPTs and three borings were com- pleted at the Adapazari Electrical Substation,

2004-01-01T23:59:59.000Z

390

Issues in Ground-Truthing Graphic Documents  

Science Conference Proceedings (OSTI)

We examine the nature of ground-truth: whether it is always well-defined fora given task, oron ly relative and approximate. In the conventional scenario, reference data is produced by recording the interpretation of each test document using a chosen ...

Daniel P. Lopresti; George Nagy

2001-09-01T23:59:59.000Z

391

Ground water work breakdown structure dictionary  

SciTech Connect

This report contains the activities that are necessary to assess in ground water remediation as specified in the UMTRA Project. These activities include the following: site characterization; remedial action compliance and design documentation; environment, health, and safety program; technology assessment; property access and acquisition activities; site remedial actions; long term surveillance and licensing; and technical and management support.

NONE

1995-04-01T23:59:59.000Z

392

Selenium in Oklahoma ground water and soil  

SciTech Connect

Selenium with a consumption of 2 liters per day (5). The objectives of this study are: (1) to determine the concentrations of Se in Oklahoma ground water and soil samples. (2) to map the geographical distribution of Se species in Oklahoma. (3) to relate groundwater depth, pH and geology with concentration of Se.

Atalay, A.; Vir Maggon, D.

1991-03-30T23:59:59.000Z

393

Ground Vibration Measurements at LHC Point 4  

Science Conference Proceedings (OSTI)

Ground vibration was measured at Large Hadron Collider (LHC) Point 4 during the winter shutdown in February 2012. This report contains the results, including power and coherence spectra. We plan to collect and analyze vibration data from representative collider halls to inform specifications for future linear colliders, such as ILC and CLIC. We are especially interested in vibration correlations between final focus lens locations.

Bertsche, Kirk; /SLAC; Gaddi, Andrea; /CERN

2012-09-17T23:59:59.000Z

394

Grounding geographic categories in the meaningful environment  

Science Conference Proceedings (OSTI)

Ontologies are a common approach to improve semantic interoperability by explicitly specifying the vocabulary used by a particular information community. Complex expressions are defined in terms of primitive ones. This shifts the problem of semantic ... Keywords: meaningful environment, semantic datum, semantic heterogeneity, symbol grounding problem

Simon Scheider; Krzysztof Janowicz; Werner Kuhn

2009-09-01T23:59:59.000Z

395

Estimation of Global Ground Heat Flux  

Science Conference Proceedings (OSTI)

This study investigates the use of a previously published algorithm for estimating ground heat flux (GHF) at the global scale. The method is based on an analytical solution of the diffusion equation for heat transfer in a soil layer and has been ...

William B. Bennett; Jingfeng Wang; Rafael L. Bras

2008-08-01T23:59:59.000Z

396

Impedance of surface footings on layered ground  

Science Conference Proceedings (OSTI)

Traditionally only the static bearing capacity and stiffness of the ground is considered in the design of wind turbine foundations. However, modern wind turbines are flexible structures with resonance frequencies as low as 0.2Hz. Unfortunately, environmental ... Keywords: Boundary elements, Domain-transformation method, Dynamic stiffness, Footing, Foundation, Layered soil, Wind turbine

L. Andersen; J. Clausen

2008-01-01T23:59:59.000Z

397

Ocean Thermal Energy Conversion Primer L. A. Vega, Ph.D.  

E-Print Network (OSTI)

a small plant mounted on a barge off Hawaii (Mini-OTEC). Subsequently, a 100 kW gross power, land separated by an interface. The upper layer is warmed by the sun and mixed to depths of about 100 m by wave.e., condenser). His concept is grounded in the thermodynamic Rankine cycle used to study steam (vapor) power

398

21-kW Thin-Film PV Technology Validation -- An NREL/Solar Energy Centre of India MOU Cooperative Project  

SciTech Connect

This paper summarizes findings during a one-week (27-31 October 2003) site visit to the Thin-Film Technology Test Bed at India's Solar Energy Centre (SEC) near New Delhi. The U.S. and Indian governments signed a Memorandum of Understanding in March 2000 to undertake a 50-50 cost-shared 21-kW thin-film PV technology validation project to evaluate the performance of thin-film photovoltaic (PV) modules under Indian climatic conditions. This project benefits Indian researchers by giving them experience with cost-effective PV materials, and it benefits the United States because data will be sent to the appropriate U.S. thin-film PV manufacturers for evaluation and analysis. During the visit, NREL personnel engaged in technical discussions regarding thin-film PV technologies with Ministry of Non-Conventional Energy Sources engineers and scientists. Issues included inspecting the newly constructed arrays, discussing better methods of electrically loading the PV arrays, taking I-V traces, and gathering baseline I-V data.

McNutt, P. F.; Ullal, H. S.

2005-01-01T23:59:59.000Z

399

Solar Energy Grid Integration Systems. Final Report of the Princeton Power Systems Development of the 100kW Demand Response Inverter.  

DOE Green Energy (OSTI)

Initiated in 2008, the Solar Energy Grid Integration (SEGIS) program is a partnership involving the U.S. Department of Energy, Sandia National Laboratories, electric utilities, academic institutions and the private sector. Recognizing the need to diversify the nation's energy portfolio, the SEGIS effort focuses on specific technologies needed to facilitate the integration of large-scale solar power generation into the nation's power grid Sandia National Laboratories (SNL) awarded a contract to Princeton Power Systems, Inc., (PPS) to develop a 100kW Advanced AC-link SEGIS inverter prototype under the Department of Energy Solar Energy Technologies Program for near-term commercial applications. This SEGIS initiative emphasizes the development of advanced inverters, controllers, communications and other balance-of-system components for photovoltaic (PV) distributed power applications. The SEGIS Stage 3 Contract was awarded to PPS on July 28, 2010. PPS developed and implemented a Demand Response Inverter (DRI) during this three-stage program. PPS prepared a 'Site Demonstration Conference' that was held on September 28, 2011, to showcase the cumulative advancements. This demo of the commercial product will be followed by Underwriters Laboratories, Inc., certification by the fourth quarter of 2011, and simultaneously the customer launch and commercial production sometime in late 2011 or early 2012. This final report provides an overview of all three stages and a full-length reporting of activities and accomplishments in Stage 3.

Bower, Ward Isaac; Heavener, Paul (Princeton Power Systems, Inc., Princeton, NJ); Sena-Henderson, Lisa; Hammell, Darren (Princeton Power Systems, Inc., Princeton, NJ); Holveck, Mark (Princeton Power Systems, Inc., Princeton, NJ); David, Carolyn; Akhil, Abbas Ali; Gonzalez, Sigifredo

2012-01-01T23:59:59.000Z

400

21-kW Thin-Film PV Technology Validation -- An NREL/Solar Energy Centre of India MOU Cooperative Project  

DOE Green Energy (OSTI)

This paper summarizes findings during a one-week (27-31 October 2003) site visit to the Thin-Film Technology Test Bed at India's Solar Energy Centre (SEC) near New Delhi. The U.S. and Indian governments signed a Memorandum of Understanding in March 2000 to undertake a 50-50 cost-shared 21-kW thin-film PV technology validation project to evaluate the performance of thin-film photovoltaic (PV) modules under Indian climatic conditions. This project benefits Indian researchers by giving them experience with cost-effective PV materials, and it benefits the United States because data will be sent to the appropriate U.S. thin-film PV manufacturers for evaluation and analysis. During the visit, NREL personnel engaged in technical discussions regarding thin-film PV technologies with Ministry of Non-Conventional Energy Sources engineers and scientists. Issues included inspecting the newly constructed arrays, discussing better methods of electrically loading the PV arrays, taking I-V traces, and gathering baseline I-V data.

McNutt, P. F.; Ullal, H. S.

2005-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "kw ground mounted" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Solar Energy Grid Integration Systems. Final Report of the Princeton Power Systems Development of the 100kW Demand Response Inverter.  

SciTech Connect

Initiated in 2008, the Solar Energy Grid Integration (SEGIS) program is a partnership involving the U.S. Department of Energy, Sandia National Laboratories, electric utilities, academic institutions and the private sector. Recognizing the need to diversify the nation's energy portfolio, the SEGIS effort focuses on specific technologies needed to facilitate the integration of large-scale solar power generation into the nation's power grid Sandia National Laboratories (SNL) awarded a contract to Princeton Power Systems, Inc., (PPS) to develop a 100kW Advanced AC-link SEGIS inverter prototype under the Department of Energy Solar Energy Technologies Program for near-term commercial applications. This SEGIS initiative emphasizes the development of advanced inverters, controllers, communications and other balance-of-system components for photovoltaic (PV) distributed power applications. The SEGIS Stage 3 Contract was awarded to PPS on July 28, 2010. PPS developed and implemented a Demand Response Inverter (DRI) during this three-stage program. PPS prepared a 'Site Demonstration Conference' that was held on September 28, 2011, to showcase the cumulative advancements. This demo of the commercial product will be followed by Underwriters Laboratories, Inc., certification by the fourth quarter of 2011, and simultaneously the customer launch and commercial production sometime in late 2011 or early 2012. This final report provides an overview of all three stages and a full-length reporting of activities and accomplishments in Stage 3.

Bower, Ward Isaac; Heavener, Paul (Princeton Power Systems, Inc., Princeton, NJ); Sena-Henderson, Lisa; Hammell, Darren (Princeton Power Systems, Inc., Princeton, NJ); Holveck, Mark (Princeton Power Systems, Inc., Princeton, NJ); David, Carolyn; Akhil, Abbas Ali; Gonzalez, Sigifredo

2012-01-01T23:59:59.000Z

402

Suggested performance specifications of standard modular controls for the automation of small hydro electric facilities. [Plant capacities from 50 kW to 15 MW  

DOE Green Energy (OSTI)

These specifications are made available by the Department of Energy for the voluntary use by any person, corporation or governmental body in the writing of purchase specifications for the automatic control of small hydro generating stations, i.e., hydro plants ranging in size from 50 kW to 15 MW. It is believed that the use of these specifications will permit competition among capable vendors and, at the same time, assure proper and reliable operation of both the automation hardware and software purchased. The specifications are detailed to a degree which should assure the interchangeability of hardware and software from various suppliers. This also increases the likelihood that spare parts and service will be available for many years. The specifications are written in modules, each of which can be included or excluded for ease of editing to match a particular application. Brief but detailed instructions are included for such editing. An extensive appendix gives the alternatives which were considered and reasons for the various choices specified.

Beckwith, R.W.

1980-06-01T23:59:59.000Z

403

Longevity of Emplacement Drift Ground Support Materials  

Science Conference Proceedings (OSTI)

The purpose of this analysis is to evaluate the factors affecting the longevity of emplacement drift ground support materials and to develop a basis for the selection of materials for ground support that will function throughout the preclosure period of a potential repository at Yucca Mountain. REV 01 ICN 01 of this analysis is developed in accordance with AP-3.10Q, Analyses and Models, Revision 2, ICN 4, and prepared in accordance with the Technical Work Plan for Subsurface Design Section FY 01 Work Activities (CRWMS M&O 2001a). The objective of this analysis is to update the previous analysis (CRWMS M&O 2000a) to account for related changes in the Ground Control System Description Document (CRWMS M&O 2000b), the Monitored Geologic Repository Project Description Document, which is included in the Requirements and Criteria for Implementing a Repository Design that can be Operated Over a Range of Thermal Modes (BSC 2001), input information, and in environmental conditions, and to provide updated information on candidate ground support materials. Candidate materials for ground support are carbon steel and cement grout. Steel is mainly used for steel sets, lagging, channel, rock bolts, and wire mesh. Cement grout is only considered in the case of grouted rock bolts. Candidate materials for the emplacement drift invert are carbon steel and granular natural material. Materials are evaluated for the repository emplacement drift environment based on the updated thermal loading condition and waste package design. The analysis consists of the following tasks: (1) Identify factors affecting the longevity of ground support materials for use in emplacement drifts. (2) Review existing documents concerning the behavior of candidate ground support materials during the preclosure period. (3) Evaluate impacts of temperature and radiation effects on mechanical and thermal properties of steel. Assess corrosion potential of steel at emplacement drift environment. (4) Evaluate factors affecting longevity of cement grouts for fully grouted rock bolt system. Provide updated information on cement grout mix design for fully grouted rock bolt system. (5) Evaluate longevity of materials for the emplacement drift invert.

D.H.Tang

2001-05-30T23:59:59.000Z

404

Estimation of Near-Ground Propagation Conditions Using Radar Ground Echo Coverage  

Science Conference Proceedings (OSTI)

The vertical gradient of refractivity (dN/dh) determines the path of the radar beam; namely, the larger the negative values of the refractivity gradient, the more the beam bends toward the ground. The variability of the propagation conditions ...

Shinju Park; Frédéric Fabry

2011-02-01T23:59:59.000Z

405

Ship-Mounted Real-Time Surface Observational System on board Indian Vessels for Validation and Refinement of Model Forcing Fields  

Science Conference Proceedings (OSTI)

A network of ship-mounted real-time Automatic Weather Stations integrated with Indian geosynchronous satellites [Indian National Satellites (INSATs)] 3A and 3C, named Indian National Centre for Ocean Information Services Real-Time Automatic ...

R. Harikumar; T. M. Balakrishnan Nair; G. S. Bhat; Shailesh Nayak; Venkat Shesu Reddem; S. S. C. Shenoi

2013-03-01T23:59:59.000Z

406

Method and apparatus for piled foundation improvement through freezing using surface mounted refrigeration units  

Science Conference Proceedings (OSTI)

This patent describes an offshore platform anchored to the seafloor by at least one tubular pile which seafloor is incapable of supporting design loads comprising: an offshore structure connected to the seafloor by at least one tubular pile; a plug contained within the tubular pile, the tubular pile being initially inserted into unfrozen ground, the plug located generally near the bottom of the pile; an insulating divider closing off the tubular pile, above the plug, such that the divider defines the top of a cylindrical reservoir, the bottom of which is defined by the plug and the sides of which are defined by the tubular pile; cooling fluid filling the reservoir; means for cooling the cooling fluid to a temperature of -20{sup 0}C to -30{sup 0}C whereby a frozen mass of soil is formed around the tubular pile, the means for cooling the cooling fluid further comprising a compressor/expander combination, the compressor/expander combination located on a deck of the offshore structure supported by the tubular pile; an insulated cold conduit means tubularly connecting the reservoir and the compressor/expander.

Spalding, A.V.; Sabet, M.H.; Hamburger, R.O.; Luk, M.H.

1989-06-06T23:59:59.000Z

407

Ground motion data for International Collider models  

SciTech Connect

The proposed location for the International Linear Collider (ILC) in the Americas region is Fermilab in Batavia Illinois. If built at this location the tunnels would be located in the Galena Platteville shale at a depth of 100 or more meters below the surface. Studies using hydro static water levels and seismometers have been conducted in the MINOS hall and the LaFrange Mine in North Aurora Illinois to determine the level of ground motion. Both these locations are in the Galena Platteville shale and indicate the typical ground motion to be expected for the ILC. The data contains both natural and cultural noise. Coefficients for the ALT law are determined. Seismic measurements at the surface and 100 meters below the surface are presented.

Volk, J.T.; LeBrun, P.; Shiltsev, V.; Singatulin, S.; /Fermilab

2007-11-01T23:59:59.000Z

408

Ground Source Heat Pump System Data Analysis  

NLE Websites -- All DOE Office Websites (Extended Search)

Peer Review Peer Review GSHP System Data Analysis Xiaobing Liu, Ph.D. Oak Ridge National Laboratory liux2@ornl.gov (865-574-2593) 4/3/2013 - GSHP Data Analysis in 1 st phase of U.S.-China CERC-BEE - GSHP ARRA Grantee Data Mining 2 | Building Technologies Office eere.energy.gov Purpose & Objectives Problem Statement: High first cost of ground heat exchangers (GHXs) and lack of knowledge/trust in achievable benefits are major barriers preventing

409

Ground Source Heat Pump System Data Analysis  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Peer Review Peer Review GSHP System Data Analysis Xiaobing Liu, Ph.D. Oak Ridge National Laboratory liux2@ornl.gov (865-574-2593) 4/3/2013 - GSHP Data Analysis in 1 st phase of U.S.-China CERC-BEE - GSHP ARRA Grantee Data Mining 2 | Building Technologies Office eere.energy.gov Purpose & Objectives Problem Statement: High first cost of ground heat exchangers (GHXs) and lack of knowledge/trust in achievable benefits are major barriers preventing

410

Entanglement Energetics in the Ground State  

E-Print Network (OSTI)

We show how many-body ground state entanglement information may be extracted from sub-system energy measurements at zero temperature. A precise relation between entanglement and energy fluctuations is demonstrated in the weak coupling limit. Examples are given with the two-state system and the harmonic oscillator, and energy probability distributions are calculated. Comparisons made with recent qubit experiments show this type of measurement provides another method to quantify entanglement with the environment.

Andrew N. Jordan; Markus Buttiker

2005-01-04T23:59:59.000Z

411

Ground Motion Model of the SLAC Site ?  

E-Print Network (OSTI)

motion p(?, L) can be written as p(?, L) = p(?)2(1 ? c(?, L)) which in turn can be transformed into P(?, k) [9]. We present a ground motion model for the SLAC site. This Measurements [2, 6] show that the fast motion in a rea-model is based on recent ground motion studies performed sonably quiet site consists primarily of elastic waves prop-at SLAC as well as on historical data. The model includes agating with a high velocity v (of the order of km/s). wave-like, diffusive and systematic types of motion. An The correlation is then completely defined by this velocity attempt is made to relate measurable secondary properties (which may be a function of frequency) and by the distri-of the ground motion with more basic characteristics such bution of the noise sources. In the case where the waves as the layered geological structure of the surrounding earth, propagate on the surface and are distributed uniformly in depth of the tunnel, etc. This model is an essential step in azimuthal angle, the correlation is given by c(?, L) = evaluating sites for a future linear collider. ?cos(?L/v cos(?))?? = J0(?L/v) and the corresponding 2-D spectrum of the ground motion is P(?, k) = 2p(?) / ? (?/v(f)) 2 ? k2, |k | ? ?/v(f). The absolute power spectrum of the fast motion, assumed for the SLAC model, corresponds to measurements performed at 2 AM in one of the quietest locations at SLAC, sector 10 of the linac [2], (see Fig.1). The spatial properties are defined by the phase velocity found from correlation measurements v(f) = 450 + 1900 exp(?f/2) (with v in m/s, f in Hz) [2]. 1

Andrei Seryi; Tor Raubenheimer

2000-01-01T23:59:59.000Z

412

Compression of ground-motion data  

Science Conference Proceedings (OSTI)

Ground motion data has been recorded for many years at Nevada Test Site and is now stored on thousands of digital tapes. The recording format is very inefficient in terms of space on tape. This report outlines a method to compress the data onto a few hundred tapes while maintaining the accuracy of the recording and allowing restoration of any file to the original format for future use. For future digitizing a more efficient format is described and suggested.

Long, J.W.

1981-04-01T23:59:59.000Z

413

ESF GROUND SUPPORT - STRUCTURAL STEEL ANALYSIS  

Science Conference Proceedings (OSTI)

The purpose and objective of this analysis are to expand the level of detail and confirm member sizes for steel sets included in the Ground Support Design Analysis, Reference 5.20. This analysis also provides bounding values and details and defines critical design attributes for alternative configurations of the steel set. One possible configuration for the steel set is presented. This analysis covers the steel set design for the Exploratory Studies Facility (ESF) entire Main Loop 25-foot diameter tunnel.

T. Misiak

1996-06-26T23:59:59.000Z

414

Radioisotope Thermoelectric Generator Transporation System licensed hardware second certification test series and package shock mount system test  

Science Conference Proceedings (OSTI)

This paper presents a summary of two separate drop test a e performed in support of the Radioisotope Thermoelectric Generator (RTG) Transportation System (RTGTS). The first portion of this paper presents the second series of drop testing required to demonstrate that the RTG package design meets the requirements of Title 10, Code of Federal Regulations, ``Part 71`` (10 CFR 71). Results of the first test series, performed in July 1994, demonstrated that some design changes were necessary. The package design was modified to improve test performance and the design changes were incorporated into the Safety Analysis Report for Packaging (SARP). The second full-size certification test article (CTA-2) incorporated the modified design and was tested at the US Department of Energy`s (DOE) Hanford Site near Richland, Washington. With the successful completion of the test series, and pending DOE Office of Facility Safety Analysis approval of the SARP, a certificate of compliance will be issued for the RTG package allowing its use. The second portion of this paper presents the design and testing of the RTG Package Mount System. The RTG package mount was designed to protect the RTG from excessive vibration during transport, provide shock protection during on/off loading, and provide a mechanism for moving the RTG package with a forklift. Military Standard (MIL-STD) 810E, Transit Drop Procedure (DOE 1989), was used to verify that the shock limiting system limited accelerations in excess of 15 G`s at frequencies below 150 Hz. Results of the package mount drop tests indicate that an impact force of 15 G`s was not exceeded in any test from a free drop height of 457 mm (18 in.).

Ferrell, P.C.; Moody, D.A.

1995-10-01T23:59:59.000Z

415

Remote measurement of ground temperature and emissivity  

SciTech Connect

TAISIR, Temperature and Imaging System InfraRed, is a nominally satellite based platform for remote sensing of the earth. One of its design features is to acquire atmospheric data simultaneous with ground data, resulting in minimal dependence on external atmospheric models for data correction. Extensive modeling of the rms error of determining a ground temperature and emissivity for a gray body has been performed as a function of integration time, spectroscopic resolution of the system, ground emissivity, atmospheric variables, and atmospheric data accuracy. We find that increased resolution improves measurement accuracy by emphasizing those regions where the atmospheric transmission is highest and atmospheric emission/absorption lowest. We find rms temperature errors {le}1K and rms emissivity errors <0.01 are obtainable for reasonable seeing and with sufficient information about the atmosphere. A new method is developed for modeling the dependence of the band-averaged transmission and emission. Monte Carlo simulations of satellite data taken using a multi-angle technique are used to derive signal-to-noise requirements. The applicability of those results to the TAISIR system requirements are discussed.

Henderson, J.R.

1994-06-01T23:59:59.000Z

416

Evacuated optical structure comprising optical bench mounted to sidewall of vacuum chamber in a manner which inhibits deflection and rotation of the optical bench  

DOE Patents (OSTI)

An improved evacuated optical structure is disclosed comprising an optical bench mounted in a vacuum vessel in a manner which inhibits transmission of movement of the vacuum vessel to the optical bench, yet provides a compact and economical structure. The vacuum vessel is mounted, through a sidewall thereof, to a support wall at four symmetrically positioned and spaced apart areas, each of which comprises a symmetrically positioned group of mounting structures passing through the sidewall of the vacuum vessel. The optical bench is pivotally secured to the vacuum vessel by four symmetrically spaced apart bolts and spherical bearings, each of which is centrally positioned within one of the four symmetrically positioned groups of vacuum vessel mounting structures. Cover plates and o-ring seals are further provided to seal the vacuum vessel mounting structures from the interior of the vacuum vessel, and venting bores are provided to vent trapped gases in the bores used to secure the cover plates and o-rings to the vacuum vessel. Provision for detecting leaks in the mounting structures from the rear surface of the vacuum vessel sidewall facing the support wall are also provided. Deflection to the optical bench within the vacuum vessel is further minimized by tuning the structure for a resonant frequency of at least 100 Hertz. 10 figures.

Bowers, J.M.

1994-04-19T23:59:59.000Z

417

Power Spectrum Analysis of Mount-Wilson Solar Diameter Measurements: Evidence for Solar Internal R-mode Oscillations  

E-Print Network (OSTI)

This article presents a power-spectrum analysis of 39,024 measurements of the solar diameter made at the Mount Wilson Observatory from 1968.670 to 1997.965. This power spectrum contains a number of very strong peaks. We find that eight of these peaks agree closely with the frequencies of r-mode oscillations for a region of the Sun where the sidereal rotation frequency is 12.08 year$^{-1}$. We estimate that there is less than one chance in ten to the sixth power of finding this pattern by chance.

Sturrock, Peter A

2010-01-01T23:59:59.000Z

418

A review of test results on solar thermal power modules with dish-mounted Stirling and Brayton cycle engines  

SciTech Connect

This paper presents results of development tests of various solar thermal parabolic dish modules and assemblies that used dish-mounted Brayton or Stirling cycle engines for production of electric power. These tests indicate that early modules achieve net efficiencies up to 29 percent in converting sunlight to electricity, as delivered to the grid. Various equipment deficiencies were observed and a number of malfunctions occurred. The performance measurements, as well as the malfunctions and other test experience, provided information that should be of value in developing systems with improved performance and reduced maintenance.

Jaffe, L.D.

1988-11-01T23:59:59.000Z

419

Diffusion Multilayer Sampling of Ground Water in Five Wells at...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Diffusion Multilayer Sampling of Ground Water in Five Wells at the Tuba City, Arizona, Site Diffusion Multilayer Sampling of Ground Water in Five Wells at the Tuba City, Arizona,...

420

Analysis of Contaminant Rebound in Ground Water in Extraction...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

of Contaminant Rebound in Ground Water in Extraction Wells at the Tuba City, Arizona, Site Analysis of Contaminant Rebound in Ground Water in Extraction Wells at the Tuba City,...

Note: This page contains sample records for the topic "kw ground mounted" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Federal Energy Management Program: Covered Product Category: Ground-Source  

NLE Websites -- All DOE Office Websites (Extended Search)

Ground-Source Heat Pumps to someone by E-mail Ground-Source Heat Pumps to someone by E-mail Share Federal Energy Management Program: Covered Product Category: Ground-Source Heat Pumps on Facebook Tweet about Federal Energy Management Program: Covered Product Category: Ground-Source Heat Pumps on Twitter Bookmark Federal Energy Management Program: Covered Product Category: Ground-Source Heat Pumps on Google Bookmark Federal Energy Management Program: Covered Product Category: Ground-Source Heat Pumps on Delicious Rank Federal Energy Management Program: Covered Product Category: Ground-Source Heat Pumps on Digg Find More places to share Federal Energy Management Program: Covered Product Category: Ground-Source Heat Pumps on AddThis.com... Energy-Efficient Products Federal Requirements Covered Product Categories

422

New and Underutilized Technology: Commercial Ground Source Heat Pumps |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Commercial Ground Source Heat Commercial Ground Source Heat Pumps New and Underutilized Technology: Commercial Ground Source Heat Pumps October 8, 2013 - 2:59pm Addthis The following information outlines key deployment considerations for commercial ground source heat pumps within the Federal sector. Benefits Commercial ground source heat pumps are ground source heat pump with loops that feed multiple packaged heat pumps and a single ground source water loop. Unit capacity is typically 1-10 tons and may be utilized in an array of multiple units to serve a large load. Application Condensing boilers are appropriate for housing, service, office, and research and development applications. Key Factors for Deployment FEMP has made great progress with commercial ground source heat pump technology deployment within the Federal sector. Primary barriers deal with

423

Category:Ground Electromagnetic Techniques | Open Energy Information  

Open Energy Info (EERE)

Ground Electromagnetic Techniques Ground Electromagnetic Techniques Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Geothermalpower.jpg Looking for the Ground Electromagnetic Techniques page? For detailed information on Ground Electromagnetic Techniques, click here. Category:Ground Electromagnetic Techniques Add.png Add a new Ground Electromagnetic Techniques Technique Subcategories This category has the following 2 subcategories, out of 2 total. E [×] Electromagnetic Profiling Techniques‎ 1 pages [+] Electromagnetic Sounding Techniques‎ (1 categories) 2 pages Pages in category "Ground Electromagnetic Techniques" The following 2 pages are in this category, out of 2 total. E Electromagnetic Profiling Techniques Electromagnetic Sounding Techniques Retrieved from "http://en.openei.org/w/index.php?title=Category:Ground_Electromagnetic_Techniques&oldid=689834"

424

Response of continuous pipelines to tunnel induced ground deformations  

E-Print Network (OSTI)

This thesis develops analytical solutions for estimating the bending moments and axial loads in a buried pipeline due to ground movements caused by tunnel construction in soft ground. The solutions combine closed-form, ...

Ieronymaki, Evangelia S

2011-01-01T23:59:59.000Z

425

Positive Cloud-to-Ground Lightning in Mesoscale Convective Systems  

Science Conference Proceedings (OSTI)

We have examined the characteristics of positive cloud-to-ground lightning flashes in Mesoscale Convective Systems observed during the Oklahoma-Kansas PRE-STORM project in 1985. Lightning frequencies and patterns of ground strike locations are ...

Steven A. Rutledge; Chungu Lu; Donald R. MacGorman

1990-09-01T23:59:59.000Z

426

A review of methods for grounding grid analysis  

Science Conference Proceedings (OSTI)

This paper presents a brief review of the most important methods available for the grounding grid analysis. This includes numerical methods intended for the grounding grid direct current, time-harmonic current and transient current energization. Emphasis ...

Petar Saraj?ev; Slavko Vujevic

2009-09-01T23:59:59.000Z

427

Ground Validation for the Tropical Rainfall Measuring Mission (TRMM)  

Science Conference Proceedings (OSTI)

An overview of the Tropical Rainfall Measuring Mission (TRMM) Ground Validation (GV) Program is presented. This ground validation (GV) program is based at NASA Goddard Space Flight Center in Greenbelt, Maryland, and is responsible for processing ...

David B. Wolff; D. A. Marks; E. Amitai; D. S. Silberstein; B. L. Fisher; A. Tokay; J. Wang; J. L. Pippitt

2005-04-01T23:59:59.000Z

428

Definition: Ground Source Heat Pumps | Open Energy Information  

Open Energy Info (EERE)

Pumps Pumps Jump to: navigation, search Dictionary.png Ground Source Heat Pumps A Ground Source Heat Pump is a central building heating and/or cooling system that takes advantage of the relatively constant year-round ground temperature to pump heat to or from the ground.[1][2][3] View on Wikipedia Wikipedia Definition A geothermal heat pump or ground source heat pump (GSHP) is a central heating and/or cooling system that pumps heat to or from the ground. It uses the earth as a heat source (in the winter) or a heat sink (in the summer). This design takes advantage of the moderate temperatures in the ground to boost efficiency and reduce the operational costs of heating and cooling systems, and may be combined with solar heating to form a geosolar system with even greater efficiency. Ground source heat pumps

429

Building Technologies Office: Ground Source Heap Pump Data Mining Research  

NLE Websites -- All DOE Office Websites (Extended Search)

Ground Source Heap Pump Ground Source Heap Pump Data Mining Research Project to someone by E-mail Share Building Technologies Office: Ground Source Heap Pump Data Mining Research Project on Facebook Tweet about Building Technologies Office: Ground Source Heap Pump Data Mining Research Project on Twitter Bookmark Building Technologies Office: Ground Source Heap Pump Data Mining Research Project on Google Bookmark Building Technologies Office: Ground Source Heap Pump Data Mining Research Project on Delicious Rank Building Technologies Office: Ground Source Heap Pump Data Mining Research Project on Digg Find More places to share Building Technologies Office: Ground Source Heap Pump Data Mining Research Project on AddThis.com... About Take Action to Save Energy Partner with DOE Activities

430

Appendix E Supporting Information for Ground Water Modeling  

Office of Legacy Management (LM)

Supporting Information for Ground Water Modeling Supporting Information for Ground Water Modeling This page intentionally left blank Contents Section Geologic Map of Site Area ........................................................................................................ E1.O Stream Flow Measurements ...................................................................................................... E2.0 Estimates of Ground Water Flow .............................................................................................. E3.0 .......................................... MODFLOW Flow Budget Analysis for OU 1 1 1 Model Subregions E4.0 ............................................................................ Burro Canyon Aquifer Ground Water Model E5.0 This page intentionally left blank

431

Cooperative heat transfer and ground coupled storage system  

DOE Patents (OSTI)

A cooperative heat transfer and ground coupled storage system wherein collected solar heat energy is ground stored and permitted to radiate into the adjacent ground for storage therein over an extended period of time when such heat energy is seasonally maximally available. Thereafter, when said heat energy is seasonally minimally available and has propagated through the adjacent ground a substantial distance, the stored heat energy may be retrieved by a circumferentially arranged heat transfer means having a high rate of heat transfer.

Metz, Philip D. (Rocky Point, NY)

1982-01-01T23:59:59.000Z

432

Ground Gravity Survey At Blue Mountain Area (Fairbank Engineering...  

Open Energy Info (EERE)

to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Ground Gravity Survey At Blue Mountain Area (Fairbank Engineering, 2006) Exploration Activity...

433

Transmission Line Grounding: Considerations and Practices Close to Substations  

Science Conference Proceedings (OSTI)

Grounding is an essential part of any electrical installation because it is needed for safe and reliable operation. In principle, a grounding system serves as a zero potential reference for the electrical system by providing a low impedance connection to earth (ground). Additionally, the design of the grounding system should be so that the buildups of potential gradients around electrical installations are limited to safe values.This report describes the aspects of the design and sizing ...

2013-12-20T23:59:59.000Z

434

Introduction Application of numerical models of ground water flow  

E-Print Network (OSTI)

Introduction Application of numerical models of ground water flow almost always involves some sort (Yeh 1986; Poeter and Hill 1997; Hill et al. 1998). Other data beside hydraulic head have been used in calibration of ground water models, including rates of ground water exchange with streams and other surface

Saiers, James

435

Using grounded theory to study the experience of software development  

Science Conference Proceedings (OSTI)

Grounded Theory is a research method that generates theory from data and is useful for understanding how people resolve problems that are of concern to them. Although the method looks deceptively simple in concept, implementing Grounded Theory research ... Keywords: Empirical software engineering research, Grounded theory, Qualitative research, Theory generation

Steve Adolph; Wendy Hall; Philippe Kruchten

2011-08-01T23:59:59.000Z

436

Precise and efficient groundness analysis for logic programs  

Science Conference Proceedings (OSTI)

We show how precise groundness information can be extracted from logic programs. The idea is to use abstract interpretation with Boolean functions as “approximations” to groundness dependencies between variables. This idea is not new, and ... Keywords: abstract interpretation, condensation, groundness analysis, propositional logic

Kim Marriott; Harald Søndergaard

1993-03-01T23:59:59.000Z

437

Advanced Computer Methods for Grounding Analysis Ignasi Colominas1  

E-Print Network (OSTI)

of grounding grids of large electrical substations in practical cases present some difficulties mainly dueAdvanced Computer Methods for Grounding Analysis Ignasi Colominas1 , Jos´e Par´is1 , Xes present the foundations of a nu- merical formulation based on the Boundary Element Method for grounding

Colominas, Ignasi

438

Posters Ground-Based Radiometric Observations  

NLE Websites -- All DOE Office Websites (Extended Search)

7 7 Posters Ground-Based Radiometric Observations of Atmospheric Water for Climate Research J. B. Snider, D. A. Hazen, A. J. Francavilla, W. B. Madsen, and M. D. Jacobson National Oceanic and Atmospheric Administration Environmental Technology Laboratory Boulder, Colorado Introduction Surface-based microwave and infrared radiometers have been employed by the National Oceanic and Atmospheric Administration's Environmental Technology Laboratory (NOAA/ETL) in climate research since 1987. The ability of these systems to operate continuously and unattended for extended periods of time has provided significant new information on atmospheric water vapor and cloud liquid. These data are being employed to improve our understanding of cloud-radiation feedback mechanisms, an understanding

439

Remote measurement of ground source emissivity  

SciTech Connect

The remote measurement of the emissivity of ground materials is of tremendous value in their identification and mapping. Traditional techniques use reflected solar radiation for this measurement for wavelengths shorter than 5 {mu}m. With the development of new techniques, the 10 Jim atmospheric transmission window might also be used for this purpose. Previous work using the multi-angle data acquisition technique demonstrated its utility to determine source thermal emission. Here we find the multi-angle technique can be used to determine the source specular reflectivity to {approximately}0.05 if there is very good system performance (NETD {approx} 0.01 K).

Henderson, J.R.

1995-07-01T23:59:59.000Z

440

Coal mine ground control. 3rd ed.  

Science Conference Proceedings (OSTI)

The third edition not only completely revises and updates the original subject areas, but also is broadened to include a number of new topics such as high horizontal stresses, computer modeling, and highwall stability. The subject areas covered in this book define the current field of coal mine ground control, except for the recently emerging topic of mine seals and some conventional subjects such as coal/rock cutting and impoundment dams. It contains 1,134 references from all published sources, and archived since 1876.

Peng, S.S.

2008-09-15T23:59:59.000Z

Note: This page contains sample records for the topic "kw ground mounted" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Superimposed particles in 1D ground states  

E-Print Network (OSTI)

For a class of nonnegative, range-1 pair potentials in one dimensional continuous space we prove that any classical ground state of lower density >=1 is a tower-lattice, i.e., a lattice formed by towers of particles the heights of which can differ only by one, and the lattice constant is 1. The potential may be flat or may have a cusp at the origin, it can be continuous, but its derivative has a jump at 1. The result is valid on finite intervals or rings of integer length and on the whole line.

Andras Suto

2010-09-02T23:59:59.000Z

442

U.S. Department of Energy UMTRA Ground Water Project Ground Water Pumping and Monitoring Plan  

Office of Legacy Management (LM)

GWMON 1.12-1 GWMON 1.12-1 U.S. Department of Energy UMTRA Ground Water Project Ground Water Pumping and Monitoring Plan for the Land Farm Pilot Test Monument Valley, Arizona August 2000 Prepared by U.S. Department of Energy Grand Junction Ofice Grand Junction, Colorado Project Number UGW-5 1 1-001 5-21-000 Document Number U0106701 This page intentionally left blank Document Number U0106701 Contents Contents 1.0 Introduction ....................................................................................................................... 1 2.0 Purpose and Scope ........................................................................................................... 1 3.0 Pilot-Test Extraction Wellfield 2 4.0 Water Elevation Measurements and Monitoring ............... 4

443

Hydromechanical transmission with three simple planetary assemblies, one sun gear being mounted on the output shaft and the other two on a common shaft connected to an input-driven hydraulic module  

DOE Patents (OSTI)

A power transmission having three simple planetary assemblies, each having its own carrier and its own planet, sun, and ring gears. A speed-varying module is connected in driving relation to the input shaft and in driving relationship to the sun gears of the first two planetary assemblies, these two sun gears being connected together on a common shaft. The speed-varying means may comprise a pair of hydraulic units hydraulically interconnected so that one serves as a pump while the other serves as a motor and vice versa, one of the units having a variable stroke and being connected in driving relation to the input shaft, the other unit, which may have a fixed stroke, being connected in driving relation to the sun gears. The input shaft is also connected to drive the second ring gear and, furthermore is clutchable to the carrier of the third planetary assembly. A brake grounds the first carrier in the first range and in reverse and causes drive to be delivered to the output through the first ring gear in a hydrostatic mode. The carrier of the second planetary assembly drives the ring gear of the third planetary assembly, which is clutchable to the output shaft, and the sun gear of the third planetary assembly is mounted rigidly to the output shaft.

Orshansky, Jr., deceased, Elias (LATE OF San Francisco, CA); Weseloh, William E. (San Diego, CA)

1978-01-01T23:59:59.000Z

444

Ground Water Management Act (Virginia) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Ground Water Management Act (Virginia) Ground Water Management Act (Virginia) Ground Water Management Act (Virginia) < Back Eligibility Agricultural Commercial Construction Developer Fed. Government Fuel Distributor General Public/Consumer Industrial Installer/Contractor Institutional Investor-Owned Utility Local Government Municipal/Public Utility Nonprofit Rural Electric Cooperative Schools State/Provincial Govt Systems Integrator Tribal Government Utility Savings Category Water Buying & Making Electricity Home Weatherization Program Info State Virginia Program Type Environmental Regulations Siting and Permitting Provider Virginia Department of Environmental Quality Under the Ground Water Management Act of 1992, Virginia manages ground water through a program regulating the withdrawals in certain areas called

445

Resistance to ground of combined grid-multiple rods electrodes  

SciTech Connect

The resistance to ground of substations ground electrodes is one of the most important parameters determining the potential rise of the grounded equipment and other metal work within substation with respect to the remote earth as well as the potentials which might be transferred outside the substation. The resistance to ground of a wide set of square and rectangular grid electrodes combined with multiple rods, buried in uniform and two-layer soils, has been analyzed using available exact computer software. Based upon the results of this analysis, analytical expressions and graphs for electrodes resistance to ground are provided, appropriate for practical application.

Nahman, J.M. [Faculty of Electrical Engineering, Belgrade (Yugoslavia)] [Faculty of Electrical Engineering, Belgrade (Yugoslavia); Djordjevic, V.B. [Energoprojekt-Hidroinzenjering, Belgrade (Yugoslavia)] [Energoprojekt-Hidroinzenjering, Belgrade (Yugoslavia)

1996-07-01T23:59:59.000Z

446

Measured Performance and Analysis of Ground Source Heat Pumps for Space Conditioning and for Water Heating in a Low-Energy Test House Operated under Simulated Occupancy Conditions  

Science Conference Proceedings (OSTI)

In this paper we present measured performance and efficiency metrics of Ground Source Heat Pumps (GSHPs) for space conditioning and for water heating connected to a horizontal ground heat exchanger (GHX) loop. The units were installed in a 345m2 (3700ft2) high-efficiency test house built with structural insulated panels (SIPs), operated under simulated occupancy conditions, and located in Oak Ridge, Tennessee (USA) in US Climate Zone 4 . The paper describes distinctive features of the building envelope, ground loop, and equipment, and provides detailed monthly performance of the GSHP system. Space conditioning needs of the house were completely satisfied by a nominal 2-ton (7.0 kW) water-to-air GSHP (WA-GSHP) unit with almost no auxiliary heat usage. Recommendations for further improvement through engineering design changes are identified. The comprehensive set of data and analyses demonstrate the feasibility and practicality of GSHPs in residential applications and their potential to help achieve source energy and greenhouse gas emission reduction targets set under the IECC 2012 Standard.

Ally, Moonis Raza [ORNL; Munk, Jeffrey D [ORNL; Baxter, Van D [ORNL; Gehl, Anthony C [ORNL

2012-01-01T23:59:59.000Z

447

Ground Motion Studies at NuMI  

Science Conference Proceedings (OSTI)

Ground motion can cause significant deterioration in the luminosity of a linear collider. Vibration of numerous focusing magnets causes continuous misalignments, which makes the beam emittance grow. For this reason, understanding the seismic vibration of all potential LC sites is essential and related efforts in many sites are ongoing. In this document we summarize the results from the studies specific to Fermilab grounds as requested by the LC project leader at FNAL, Shekhar Mishra in FY04-FY06. The Northwestern group focused on how the ground motion effects vary with depth. Knowledge of depth dependence of the seismic activity is needed in order to decide how deep the LC tunnel should be at sites like Fermilab. The measurements were made in the NuMI tunnel, see Figure 1. We take advantage of the fact that from the beginning to the end of the tunnel there is a height difference of about 350 ft and that there are about five different types of dolomite layers. The support received allowed to pay for three months of salary of Michal Szleper. During this period he worked a 100% of his time in this project. That include one week of preparation: 2.5 months of data taking and data analysis during the full period of the project in order to guarantee that we were recording high quality data. We extended our previous work and made more systematic measurements, which included detailed studies on stability of the vibration amplitudes at different depths over long periods of time. As a consequence, a better control and more efficient averaging out of the daytime variation effects were possible, and a better study of other time dependences before the actual depth dependence was obtained. Those initial measurements were made at the surface and are summarized in Figure 2. All measurements are made with equipment that we already had (two broadband seismometers KS200 from GEOTECH and DL-24 portable data recorder). The offline data analysis took advantage of the full Fourier spectra information and the noise was properly subtracted. The basic formalism is summarized if Figure 3. The second objective was to make a measurement deeper under ground (Target hall, Absorber hall and Minos hall - 150 ft to 350 ft), which previous studies did not cover. All results are summarized in Figure 3 and 4. The measurements were covering a frequency range between 0.1 to 50 Hz. The data was taken continuously for at least a period of two weeks in each of the locations. We concluded that the dependence on depth is weak, if any, for frequencies above 1 Hz and not visible at all at lower frequencies. Most of the attenuation (factor of about 2-3) and damping of ground motion that is due to cultural activity at the surface is not detectable once we are below 150 ft underground. Therefore, accelerator currently under consideration can be build at the depth and there is no need to go deeper underground is built at Fermi National Laboratory.

Mayda M. Velasco; Michal Szleper

2012-02-20T23:59:59.000Z

448

Comparison of energy efficiency between variable refrigerant flow systems and ground source heat pump systems  

E-Print Network (OSTI)

Performance of ground source heat pump system in a near-zerosimulation tool for ground- source heat pump system designflow systems and ground source heat pump systems Abstract

Hong, Tainzhen

2010-01-01T23:59:59.000Z

449

Method and apparatus for mounting a dichroic mirror in a microwave powered lamp assembly using deformable tabs  

DOE Patents (OSTI)

A microwave powered electrodeless lamp includes an improved screen unit having mesh and solid sections with an internal reflector secured at the juncture of the two sections to reflect light into a light-transmitting chamber defined in the lamp microwave cavity by the reflector and the mesh section. A discharge envelope of a bulb is disposed in the light-transmitting chamber. Light emitted from the envelope is prevented by the reflector from entering the cavity portion bounded by the solid section of the screen. The reflector is mounted in the cavity by tabs formed in the screen unit and bendable into the cavity to define support planes abutting respective surfaces of the reflector. The mesh section and tabs are preferably formed by etching a thin metal sheet. 7 figs.

Ury, M.; Sowers, F.; Harper, C.; Love, W.

1998-11-24T23:59:59.000Z

450

Method and apparatus for mounting a dichroic mirror in a microwave powered lamp assembly using deformable tabs  

DOE Patents (OSTI)

A microwave powered electrodeless lamp includes an improved screen unit having mesh and solid sections with an internal reflector secured at the juncture of the two sections to reflect light into a light-transmitting chamber defined in the lamp microwave cavity by the reflector and the mesh section. A discharge envelope of a bulb is disposed in the light-transmitting chamber. Light emitted from the envelope is prevented by the reflector from entering the cavity portion bounded by the solid section of the screen. The reflector is mounted in the cavity by tabs formed in the screen unit and bendable into the cavity to define support planes abutting respective surfaces of the reflector. The mesh section and tabs are preferably formed by etching a thin metal sheet.

Ury, Michael (Bethesda, MD); Sowers, Frank (Frederick, MD); Harper, Curt (Wheaton, MD); Love, Wayne (Olney, MD)

1998-01-01T23:59:59.000Z

451

Investigation of gas hydrate-bearing sandstone reservoirs at the "Mount Elbert" stratigraphic test well, Milne Point, Alaska  

SciTech Connect

In February 2007, the U.S. Department of Energy, BP Exploration (Alaska), Inc., and the U.S. Geological Survey conducted an extensive data collection effort at the "Mount Elbert #1" gas hydrates stratigraphic test well on the Alaska North Slope (ANS). The 22-day field program acquired significant gas hydrate-bearing reservoir data, including a full suite of open-hole well logs, over 500 feet of continuous core, and open-hole formation pressure response tests. Hole conditions, and therefore log data quality, were excellent due largely to the use of chilled oil-based drilling fluids. The logging program confirmed the existence of approximately 30 m of gashydrate saturated, fine-grained sand reservoir. Gas hydrate saturations were observed to range from 60% to 75% largely as a function of reservoir quality. Continuous wire-line coring operations (the first conducted on the ANS) achieved 85% recovery through 153 meters of section, providing more than 250 subsamples for analysis. The "Mount Elbert" data collection program culminated with open-hole tests of reservoir flow and pressure responses, as well as gas and water sample collection, using Schlumberger's Modular Formation Dynamics Tester (MDT) wireline tool. Four such tests, ranging from six to twelve hours duration, were conducted. This field program demonstrated the ability to safely and efficiently conduct a research-level openhole data acquisition program in shallow, sub-permafrost sediments. The program also demonstrated the soundness of the program's pre-drill gas hydrate characterization methods and increased confidence in gas hydrate resource assessment methodologies for the ANS.

Boswell, R.M.; Hunter, R. (ASRC Energy Services, Anchorage, AK); Collett, T. (USGS, Denver, CO); Digert, S. (BP Exploration (Alaska) Inc., Anchorage, AK); Hancock, S. (RPS Energy Canada, Calgary, Alberta, Canada); Weeks, M. (BP Exploration (Alaska) Inc., Anchorage, AK); Mt. Elbert Science Team

2008-01-01T23:59:59.000Z

452

Definition: Ground Magnetics | Open Energy Information  

Open Energy Info (EERE)

Magnetics Magnetics Jump to: navigation, search Dictionary.png Ground Magnetics The surface magnetic method is the study of the distribution of magnetic minerals in the upper 20-30km of the earth's crust, recorded at an observation point on the earth's surface.[1][2] View on Wikipedia Wikipedia Definition A magnetometer, (pronounced mag-ne-TOM-e-ter), is a measuring instrument used to measure the strength and/or direction of the magnetic field, produced either in the laboratory or existing in nature. Some countries such as the USA, Canada and Australia classify the more sensitive magnetometers as military technology, and control their distribution. The International System of Units unit of measure for the strength of a magnetic field is the Tesla. This is a very large unit of magnetic field.

453

Pacific Northwest National Laboratory Grounds Maintenance  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Pacific Pacific Northwest National Laboratory (PNNL) operates an award-winning grounds maintenance program that comprises a comprehensive landscape and irrigation management program. The program has helped the laboratory reduce its water use for irrigation by 30%. PNNL is located in Richland, Washington, and is managed and operated by Battelle for the U.S. Department of Energy (DOE). PNNL scientists and engineers perform research on a variety of subjects, including energy and national security. PNNL has more than 4,200 staff members, sits on 600 acres, and houses 2 million square feet of facilities. The laboratory is located in an arid region of the state, receiving only eight inches of precipitation annually. It has more than 100 acres of turf and landscaped areas and

454

Inefficient remediation of ground-water pollution  

SciTech Connect

The problem of trying to remove ground-water pollution by pumping and treating are pointed out. Various Superfund sites are discussed briefly. It is pointed out that many chemicals have been discarded in an undocumented manner, and their place in the groundwater is not known. Results of a remedial program to remove perchloroethylene at a concentration of 6132 parts per billion from groundwater in a site in New Jersey showed that with an average extraction rate of 300 gallons per minute from 1978 to 1984 contamination level was lowered below 100 parts per billion. However, after shutdown of pumping the level rose to 12,588 parts per billion in 1988. These results lead the author to propose that the practical solutions for water supplies may be treatment at the time it enters the system for use.

Abelson, P.H.

1990-11-09T23:59:59.000Z

455

(Assessment of ground-coupled heat pumps)  

Science Conference Proceedings (OSTI)

The objectives of the third working meeting were to assess the accomplishments to date in direct-expansion ground-coupled heat exchanger study and to discuss what should be done in the future. The design concepts presented by each participating country are quite similar. Annex XV enables us to exchange information on experimental and analytical results. The third working meeting was hosted by Oberoesterreichische Kraftwerke Aktiengesellschaft (OKA) Power Co. at Linz, Austria and by the Department of Thermal Engineering, Graz University of Technology at Graz, Austria. The meeting was chaired by Dr. O.J. Svec of Canada. The next working meeting will be held in Japan. The United States will host the last meeting at ORNL in September 1990. 5 refs.

Mei, V.C.

1989-12-05T23:59:59.000Z

456

Ground freezing for containment of hazardous waste  

SciTech Connect

The freezing of ground for the containment of subsurface hazardous waste is a promising method that is environmentally friendly and offers a safe alternative to other methods of waste retention in many cases. The frozen soil method offers two concepts for retaining waste. One concept is to freeze the entire waste area into a solid block of frozen soil thus locking the waste in situ. For small areas where the contaminated soil does not include vessels that would rupture from frost action, this concept may be simpler to install. A second concept, of course, is to create a frozen soil barrier to confine the waste within prescribed unfrozen soil boundaries; initial research in this area was funded by EPA, Cincinnati, OH, and the Army Corps of Engineers. The paper discusses advantages and limitations, a case study from Oak Ridge, TN, and a mesh generation program that simulates the cryogenic technology.

Sayles, F.N.; Iskandar, I.K.

1998-07-01T23:59:59.000Z

457

Innovation Approaches to Development and Ground Testing of Advanced Bimodal Space Power and Propulsion Systems  

DOE Green Energy (OSTI)

The last major development effort for nuclear power and propulsion systems ended in 1993. Currently, there is not an initiative at either the National Aeronautical and Space Administration (NASA) or the U.S. Department of Energy (DOE) that requires the development of new nuclear power and propulsion systems. Studies continue to show nuclear technology as a strong technical candidate to lead the way toward human exploration of adjacent planets or provide power for deep space missions, particularly a 15,000 lbf bimodal nuclear system with 115 kW power capability. The development of nuclear technology for space applications would require technology development in some areas and a major flight qualification program. The last major ground test facility considered for nuclear propulsion qualification was the U.S. Air Force/DOE Space Nuclear Thermal Propulsion Project. Seven years have passed since that effort, and the questions remain the same, how to qualify nuclear power and propulsion systems for future space flight. It can be reasonably assumed that much of the nuclear testing required to qualify a nuclear system for space application will be performed at DOE facilities as demonstrated by the Nuclear Rocket Engine Reactor Experiment (NERVA) and Space Nuclear Thermal Propulsion (SNTP) programs. The nuclear infrastructure to support testing in this country is aging and getting smaller, though facilities still exist to support many of the technology development needs. By renewing efforts, an innovative approach to qualifying these systems through the use of existing facilities either in the U.S. (DOE's Advance Test Reactor, High Flux Irradiation Facility and the Contained Test Facility) or overseas should be possible.

Hill, T.; Noble, C.; Martinell, J. (INEEL); Borowski, S. (NASA Glenn Research Center)

2000-07-14T23:59:59.000Z

458

Ground Truth Collections at the MTI Core Sites  

Science Conference Proceedings (OSTI)

The Savannah River Technology Center (SRTC) selected 13 sites across the continental US and one site in the western Pacific to serve as the primary or core site for collection of ground truth data for validation of MTI science algorithms. Imagery and ground truth data from several of these sites are presented in this paper. These sites are the Comanche Peak, Pilgrim and Turkey Point power plants, Ivanpah playas, Crater Lake, Stennis Space Center and the Tropical Western Pacific ARM site on the island of Nauru. Ground truth data includes water temperatures (bulk and skin), radiometric data, meteorological data and plant operating data. The organizations that manage these sites assist SRTC with its ground truth data collections and also give the MTI project a variety of ground truth measurements that they make for their own purposes. Collectively, the ground truth data from the 14 core sites constitute a comprehensive database for science algorithm validation.

Garrett, A.J.

2001-01-25T23:59:59.000Z

459

Ground Magnetics At Marysville Mt Area (Blackwell) | Open Energy  

Open Energy Info (EERE)

Ground Magnetics At Marysville Mt Area (Blackwell) Ground Magnetics At Marysville Mt Area (Blackwell) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Ground Magnetics At Marysville Mt Area (Blackwell) Exploration Activity Details Location Marysville Mt Area Exploration Technique Ground Magnetics Activity Date Usefulness not useful DOE-funding Unknown Notes A ground magnetic survey located no anomaly with an amplitude of more than 20 or 30 gammas that could be associated with the thermal anomaly, however the magnetic data did outline the Cretaceous stock in great detail and allow the removal from the gravity field of the effect of the stock. References D. D. Blackwell (Unknown) Exploration In A Blind Geothermal Area Near Marysville, Montana, Usa Retrieved from "http://en.openei.org/w/index.php?title=Ground_Magnetics_At_Marysville_Mt_Area_(Blackwell)&oldid=389390"

460

Geothermal Ground-Loop Preinstallation Project at Walden Pond  

Science Conference Proceedings (OSTI)

Geothermal ground-source heat pumps can help utilities increase electricity sales while reducing peak demands, but high ground-loop installation costs are a barrier to widespread acceptance. This project, conducted with Public Service Company of Indiana, demonstrated that mass installation of ground loops in a residential subdivision prior to home construction can substantially reduce installed cost for both horizontal and vertical loop configurations.

1990-09-05T23:59:59.000Z

Note: This page contains sample records for the topic "kw ground mounted" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Proceedings, 25th international conference on ground control in mining  

Science Conference Proceedings (OSTI)

Topics covered include: computer and physical modelling; geology in ground control; geophysics in ground control; ground control; impoundments stability; longwall gateroad support design; longwall operations; longwall shields and standing supports; mine design; multiple-seam mining interactions; pillar and pillar extraction; roof bolting; roof bolting - resin; and subsidence. Most of the topics include a retrospective paper which summarises the progress of the subject field during the past 25 years.

Peng, S.S.; Mark, C.; Finfinger, G.; Tadolini, S.; Wahab Khair, A.; Heasley, K.; Luo, Y. (eds.)

2006-07-01T23:59:59.000Z

462

Contol of Surface Mounted Permanent Magnet Motors with Special Application to Motors with Fractional-Slot Concentrated Windings  

SciTech Connect

A 30-pole, 6-kW prototype of a fractional-slot permanent magnet synchronous motor (PMSM) design has been developed to operate at a maximum speed of 6000 rpm [1,2]. This machine has significantly more inductance than regular PMSMs with distributed windings. The prototype was delivered in April 2006 to the Oak Ridge National Laboratory (ORNL) for testing and development of a suitable controller. To prepare for this test/control development effort, ORNL used PMSM models developed over a number of previous studies to preview the control issues that arise when a dynamic controller drives a high inductance PMSM machine during steady state performance evaluations. The detailed steady state model developed includes all motor and inverter loss mechanisms and was useful for assessing the performance of the dynamic controller before it was put into operation. This report documents the results of tests demonstrating the effectiveness of ORNL's simple low-cost control scheme during characterization of the fractional-slot concentrated windings (FSCW) PMSM motor. The control scheme is simple because only the supply voltage magnitude and the phase angle between the back-electromotive force (emf) and the supply voltage is controlled. It is low-cost because it requires no current or phase voltage sensors.

Patil, N.; Lawler, J.S.; McKeever, J.

2007-07-31T23:59:59.000Z

463

Contol of Surface Mounted Permanent Magnet Motors with Special Application to Motors with Fractional-Slot Concentrated Windings  

SciTech Connect

A 30-pole, 6-kW prototype of a fractional-slot permanent magnet synchronous motor (PMSM) design has been developed to operate at a maximum speed of 6000 rpm [1,2]. This machine has significantly more inductance than regular PMSMs with distributed windings. The prototype was delivered in April 2006 to the Oak Ridge National Laboratory (ORNL) for testing and development of a suitable controller. To prepare for this test/control development effort, ORNL used PMSM models developed over a number of previous studies to preview the control issues that arise when a dynamic controller drives a high inductance PMSM machine during steady state performance evaluations. The detailed steady state model developed includes all motor and inverter loss mechanisms and was useful for assessing the performance of the dynamic controller before it was put into operation. This report documents the results of tests demonstrating the effectiveness of ORNL's simple low-cost control scheme during characterization of the fractional-slot concentrated windings (FSCW) PMSM motor. The control scheme is simple because only the supply voltage magnitude and the phase angle between the back-electromotive force (emf) and the supply voltage is controlled. It is low-cost because it requires no current or phase voltage sensors.

Patil, N.; Lawler, J.S.; McKeever, J.

2007-07-31T23:59:59.000Z

464

Combined permeable pavement and ground source heat pump systems.  

E-Print Network (OSTI)

??The PhD thesis focuses on the performance assessment of permeable pavement systems incorporating ground source heat pumps (GSHP). The relatively high variability of temperature in… (more)

Grabowiecki, Piotr

2010-01-01T23:59:59.000Z

465

EVALUATION AND OPTIMIZATION RESEARCH OF GROUND SOURCE HEAT PUMP.  

E-Print Network (OSTI)

??Nowadays energy efficiency and environmental protection have got particular attention. After the sustainable development theory had been put forward decades ago. Ground source heat pump… (more)

Zhou, Taian

2011-01-01T23:59:59.000Z

466

Battle Ground, Indiana: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

with form History Share this page on Facebook icon Twitter icon Battle Ground, Indiana: Energy Resources Jump to: navigation, search Equivalent URI DBpedia Coordinates...

467

Colorado Wind Resource at 50 Meters Above Ground Level  

NLE Websites -- All DOE Office Websites (Extended Search)

Wind Resource at 50 Meters Above Ground Level Metadata also available as Metadata: IdentificationInformation DataQualityInformation SpatialDataOrganizationInformation...

468

Ground Gravity Survey At Newberry Caldera Area (DOE GTP) | Open...  

Open Energy Info (EERE)

GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Ground Gravity Survey At Newberry Caldera Area (DOE GTP) Exploration Activity Details Location Newberry Caldera Area...

469

Ground Gravity Survey At Under Steamboat Springs Area (Warpinski...  

Open Energy Info (EERE)

to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Ground Gravity Survey At Under Steamboat Springs Area (Warpinski, Et Al., 2002) Exploration Activity...

470

Ground Gravity Survey At San Francisco Volcanic Field Area (Warpinski...  

Open Energy Info (EERE)

Ground Gravity Survey At San Francisco Volcanic Field Area (Warpinski, Et Al., 2004) Exploration Activity Details Location San Francisco Volcanic Field Area Exploration Technique...

471

Ground Gravity Survey At Cove Fort Area - Vapor (Warpinski, Et...  

Open Energy Info (EERE)

to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Ground Gravity Survey At Cove Fort Area (Warpinski, Et Al., 2004) Exploration Activity Details...

472

Ground Gravity Survey At Lake City Hot Springs Area (Warpinski...  

Open Energy Info (EERE)

to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Ground Gravity Survey At Lake City Hot Springs Area (Warpinski, Et Al., 2004) Exploration Activity...

473

Ground Gravity Survey At Coso Geothermal Area (1980) | Open Energy...  

Open Energy Info (EERE)

Activity Details Location Coso Geothermal Area Exploration Technique Ground Gravity Survey Activity Date 1980 Usefulness not indicated DOE-funding Unknown Notes The...

474

Ground Gravity Survey At Dixie Valley Geothermal Field Area ...  

Open Energy Info (EERE)

Details Location Dixie Valley Geothermal Field Area Exploration Technique Ground Gravity Survey Activity Date Usefulness useful DOE-funding Unknown Notes The gravity data are...

475

Ground Gravity Survey At Kilauea East Rift Area (Broyles, Et...  

Open Energy Info (EERE)

Activity Details Location Kilauea East Rift Area Exploration Technique Ground Gravity Survey Activity Date Usefulness not indicated DOE-funding Unknown References M. L....

476

Ground Gravity Survey At Dixie Valley Geothermal Field Area ...  

Open Energy Info (EERE)

In Dixie Valley, Nevada Retrieved from "http:en.openei.orgwindex.php?titleGroundGravitySurveyAtDixieValleyGeothermalFieldArea(Blackwell,EtAl.,2009)&oldid38834...

477

Ground Gravity Survey At Under Steamboat Springs Area (Warpinski...  

Open Energy Info (EERE)

to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Ground Gravity Survey At Under Steamboat Springs Area (Warpinski, Et Al., 2004) Exploration Activity...

478

Ground Gravity Survey At Walker Lake Valley Area (Shoffner, Et...  

Open Energy Info (EERE)

to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Ground Gravity Survey At Walker Lake Valley Area (Shoffner, Et Al., 2010) Exploration Activity...

479

Ground Gravity Survey At Baltazor Hot Springs Area (Isherwood...  

Open Energy Info (EERE)

to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Ground Gravity Survey At Baltazor Hot Springs Area (Isherwood & Mabey, 1978) Exploration Activity...

480

Ground Gravity Survey At Raft River Geothermal Area (1978) |...  

Open Energy Info (EERE)

Activity Details Location Raft River Geothermal Area Exploration Technique Ground Gravity Survey Activity Date 1978 Usefulness not indicated DOE-funding Unknown Exploration...

Note: This page contains sample records for the topic "kw ground mounted" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Renewable Energy Opportunities at Yuma Proving Ground, Arizona  

DOE Green Energy (OSTI)

This document provides an overview of renewable resource potential at Yuma Proving Ground, based primarily upon analysis of secondary data sources supplemented with limited on-site evaluations.

Orrell, Alice C.; Kora, Angela R.; Russo, Bryan J.; Williamson, Jennifer L.; Weimar, Mark R.; Gorrissen, Willy J.; Dixon, Douglas R.

2010-06-30T23:59:59.000Z

482

Monticello Mill Tailings, Operable Unit III Surface and Ground...  

Office of Legacy Management (LM)

Action activities included millsite dewatering and treatment, initiation of a ground water management policy to prevent use Monticello Mill Tailings Site, Operable Unit III...

483

Session Papers Preliminary Analysis of Ground-Based Microwave...  

NLE Websites -- All DOE Office Websites (Extended Search)

Analysis of Ground-Based Microwave and Infrared Radiance Observations During the Pilot Radiation OBservation Experiment E. R. Westwater, Y. Han, J. H. Churnside, and J. B....

484

Posters Preliminary Analysis of Ground-Based Microwave and Infrared...  

NLE Websites -- All DOE Office Websites (Extended Search)

Analysis of Ground-Based Microwave and Infrared Radiance Observations During the Pilot Radiation OBservation Experiment E. R. Westwater, Y. Han, J. H. Churnside, and J. B....

485

First Mira Runs Break New Ground with Turbulence Simulations...  

NLE Websites -- All DOE Office Websites (Extended Search)

First Mira Runs Break New Ground with Turbulence Simulations July 16, 2013 Printer-friendly version Shortly after Mira, the ALCF's new 10-petaflops supercomputer, entered...

486

Ground resistance of concrete foundations in substation yards  

SciTech Connect

The reinforced concrete foundations in a substation yard have extensive reinforcing steel which is in metallic connection with the laid ground conductor. The foundations may contribute significantly to the dissipation of the fault and leakage currents. Simple to use equations and graphs are presented in this paper to determine the ground resistance of various types of foundations encountered in substation yards. The validity of the analytical approach has been verified with scale model tests. The ground resistance of the foundations estimated as suggested in the paper can be used to evaluate the role of the foundations as grounding element.

Thapar, B.; Ferrer, O. (Montana State Univ., Bozeman, MT (USA)); Blank, D.A. (Bonneville Power Administration, Portland, OR (USA))

1990-01-01T23:59:59.000Z

487

Ground-Based Nuclear Detonation Detection | National Nuclear...  

National Nuclear Security Administration (NNSA)

Ground-Based Nuclear Detonation Detection | National Nuclear Security Administration Our Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency...

488

Ground Gravity Survey At Snake River Plain Region (DOE GTP) ...  

Open Energy Info (EERE)

Snake River Plain Region (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Ground Gravity Survey At Snake River Plain Region (DOE GTP)...

489

Ground Magnetics At Silver Peak Area (DOE GTP) | Open Energy...  

Open Energy Info (EERE)

Silver Peak Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Ground Magnetics At Silver Peak Area (DOE GTP) Exploration Activity...

490

SARA Cadets and Midshipmen Hit the Ground Running | National...  

NLE Websites -- All DOE Office Websites (Extended Search)

SARA Cadets and Midshipmen Hit the Ground Running | National Nuclear Security Administration Our Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy...

491

SCIENTIFIC EFFICIENCY OF GROUND-BASED TELESCOPES  

SciTech Connect

I scanned the six major astronomical journals of 2008 for all 1589 papers that are based on new data obtained from ground-based optical/IR telescopes worldwide. Then I collected data on numbers of papers, citations to them in 3+ years, the most-cited papers, and annual operating costs. These data are assigned to four groups by telescope aperture. For instance, while the papers from telescopes with an aperture >7 m average 1.29 more citations than those with an aperture of 2 to <4 m, this represents a small return for a factor of four difference in operating costs. Among the 17 papers that have received {>=}100 citations in 3+ years, only half come from the large (>7 m) telescopes. I wonder why the large telescopes do so relatively poorly and suggest possible reasons. I also found that papers based on archival data, such as the Sloan Digital Sky Survey, produce 10.6% as many papers and 20.6% as many citations as those based on new data. Also, the 577.2 papers based on radio data produced 36.3% as many papers and 33.6% as many citations as the 1589 papers based on optical/IR telescopes.

Abt, Helmut A., E-mail: abt@noao.edu [Kitt Peak National Observatory, P.O. Box 26732, Tucson, AZ 85726-6732 (United States)

2012-10-01T23:59:59.000Z

492

Networked Acoustic Modems for Real-Time Data Telemetry from Distributed Subsurface Instruments in the Coastal Ocean: Application to Array of Bottom-Mounted ADCPs  

Science Conference Proceedings (OSTI)

Through the winter and spring of 2002, networked acoustic modems demonstrated real-time wireless data telemetry from an array of bottom-mounted acoustic Doppler current profilers (ADCPs) on the inner continental shelf 20–60 m deep off of Montauk ...

Daniel L. Codiga; Joseph A. Rice; Paul A. Baxley; David Hebert

2005-06-01T23:59:59.000Z

493

A High-Resolution Record of Atmospheric Dust Composition and Variability since a.d. 1650 from a Mount Everest Ice Core  

Science Conference Proceedings (OSTI)

A Mount Everest ice core analyzed at high resolution for major and trace elements (Sr, Cs, Ba, La, Ce, Pr, Nd, Sm, Eu, Tb, Dy, Ho, Er, Tm, Yb, Lu, Bi, U, Tl, Al, S, Ca, Ti, V, Cr, Mn, Fe, Co) and spanning the period a.d. 1650–2002 is used to ...

S. Kaspari; P. A. Mayewski; M. Handley; S. Kang; S. Hou; S. Sneed; K. Maasch; D. Qin

2009-07-01T23:59:59.000Z

494

Solving Satisfiability Problems by the Ground-State Quantum Computer  

E-Print Network (OSTI)

A quantum algorithm is proposed to solve the Satisfiability problems by the ground-state quantum computer. The scale of the energy gap of the ground-state quantum computer is analyzed for the 3-bit Exact Cover problem. The time cost of this algorithm on the general SAT problems is discussed.

Wenjin Mao

2005-06-23T23:59:59.000Z

495

Solving satisfiability problems by the ground-state quantum computer  

Science Conference Proceedings (OSTI)

A quantum algorithm is proposed to solve the satisfiability (SAT) problems by the ground-state quantum computer. The scale of the energy gap of the ground-state quantum computer is analyzed for the 3-bit exact cover problem. The time cost of this algorithm on the general SAT problems is discussed.

Mao Wenjin [Department of Physics and Astronomy, Stony Brook University, Stony Brook, New York 11794, USA and 20 Hearthstone Drive, Edison, New Jersey 08820 (United States)

2005-11-15T23:59:59.000Z

496

Overhead Transmission Line Lightning and Grounding Reference Book 2012  

Science Conference Proceedings (OSTI)

In North America and many other parts of the world, lightning remains the primary cause of transmission line outages, momentary interruptions, and reliability and maintenance problems. The lightning performance of transmission lines may be improved by applying overhead ground wires, providing a low impedance connection to ground, and selecting appropriate insulation levels for the phase conductors. The success of these measures is not always ...

2012-12-12T23:59:59.000Z

497

Simplified two layer model substation ground grid design methodology  

SciTech Connect

This paper presents a simplified approach to the design of substation ground grids in non-uniform soil conditions. The procedure is based on the interpretation of principles enunciated in the IEEE Standard 80-1986, with the supporting data having been obtained from actual field tests on substation ground grids.

Lazzara, J.; Barbeito, N. (Florida Power Corp., St. Petersburg, FL (USA))

1990-10-01T23:59:59.000Z

498

Ground water hydrology report: Revision 1, Attachment 3. Final  

SciTech Connect

This report presents ground water hydrogeologic activities for the Maybell, Colorado, Uranium Mill Tailings Remedial Action Project site. The Department of Energy has characterized the hydrogeology, water quality, and water resources at the site and determined that the proposed remedial action would comply with the requirements of the EPA ground water protection standards.

NONE

1996-12-01T23:59:59.000Z

499

Temporary Grounding and Bonding Practices in Nuclear Electric Generating Stations  

Science Conference Proceedings (OSTI)

Correct written temporary grounding practices inside generating stations are an important industrial safety issue, as well as an important plant status control issue. An extraordinary amount of regulations, standards, and information is available for temporary grounding practices in transmission and delivery (T&D), but very little is written about inside plant practices.

2008-12-22T23:59:59.000Z

500

Ultrahigh vacuum sample mount for x-ray photoelectron spectroscopy up to very high temperature (150-1400 K)  

SciTech Connect

Spectroscopic studies are rarely performed at very high temperature, especially when combined with light from a synchrotron source. Demanding conditions of maintaining ultrahigh vacuum (UHV) during heating, together with the typically brief access to beam time at multiuser synchrotron end stations, may contribute to some of the reasons for the difficulty of such experiments. Consequently, a large number of materials with interesting properties and industrial applications at high temperature remain unexplored. The authors describe here a simple portable sample mount assembly that can be easily utilized at a beamline, with potential utility for a variety of spectroscopic measurements requiring elevated temperatures and an UHV environment. In the specific application described here, the authors use a resistive cartridge heater interfaced with a standard manipulator previously designed for cooling by liquid nitrogen with an UHV chamber and a cylindrical mirror analyzer for x-ray photoemission spectroscopy (XPS) [also known as electron spectroscopy for chemical analysis (ESCA)] at the Synchrotron Radiation Center in Stoughton, WI. The heater cartridge required only modest power to reach target temperatures using an open-loop temperature control. Finally, the authors describe the measurements of XPS (ESCA) and total-electron yield x-ray absorption spectroscopy on nanopowders and on single crystals grown by them. They emphasize the simplicity of the setup, which they believe would be of interest to groups performing measurements at large facilities, where access and time are both limited.