Sample records for intensity discharge lighting

  1. Light intensity compressor

    DOE Patents [OSTI]

    Rushford, Michael C. (Livermore, CA)

    1990-01-01T23:59:59.000Z

    In a system for recording images having vastly differing light intensities over the face of the image, a light intensity compressor is provided that utilizes the properties of twisted nematic liquid crystals to compress the image intensity. A photoconductor or photodiode material that is responsive to the wavelength of radiation being recorded is placed adjacent a layer of twisted nematic liquid crystal material. An electric potential applied to a pair of electrodes that are disposed outside of the liquid crystal/photoconductor arrangement to provide an electric field in the vicinity of the liquid crystal material. The electrodes are substantially transparent to the form of radiation being recorded. A pair of crossed polarizers are provided on opposite sides of the liquid crystal. The front polarizer linearly polarizes the light, while the back polarizer cooperates with the front polarizer and the liquid crystal material to compress the intensity of a viewed scene. Light incident upon the intensity compressor activates the photoconductor in proportion to the intensity of the light, thereby varying the field applied to the liquid crystal. The increased field causes the liquid crystal to have less of a twisting effect on the incident linearly polarized light, which will cause an increased percentage of the light to be absorbed by the back polarizer. The intensity of an image may be compressed by forming an image on the light intensity compressor.

  2. High intensity discharge device containing oxytrihalides

    DOE Patents [OSTI]

    Lapatovich, W.P.; Keeffe, W.M.; Liebermann, R.W.; Maya, J.

    1987-06-09T23:59:59.000Z

    A fill composition for a high intensity discharge device including mercury, niobium oxytrihalide, and a molecular stabilization agent is provided. The molar ratio of niobium oxytrihalide to the molecular stabilization agent in the fill is in the range of from about 5:1 to about 7.5:1. Niobium oxytrihalide is present in the fill in sufficient amount to produce, by dissociation in the discharge, atomic niobium, niobium oxide, NbO, and niobium dioxide, NbO[sub 2], with the molar ratio of niobium-containing vapor species to mercury in the fill being in the range of from about 0.01:1 to about 0.50:1; and mercury pressure of about 1 to about 50 atmospheres at lamp operating temperature. There is also provided a high intensity discharge device comprising a sealed light-transmissive arc tube; the arc tube including the above-described fill; and an energizing means for producing an electric discharge within the arc tube. 7 figs.

  3. High intensity discharge device containing oxytrihalides

    DOE Patents [OSTI]

    Lapatovich, Walter P. (Hudson, MA); Keeffe, William M. (Rockport, MA); Liebermann, Richard W. (Danvers, MA); Maya, Jakob (Brookline, MA)

    1987-01-01T23:59:59.000Z

    A fill composition for a high intensity discharge device including mercury, niobium oxytrihalide, and a molecular stabilization agent is provided. The molar ratio of niobium oxytrihalide to the molecular stabilization agent in the fill is in the range of from about 5:1 to about 7.5:1. Niobium oxytrihalide is present in the fill in sufficient amount to produce, by dissociation in the discharge, atomic niobium, niobium oxide, NbO, and niobium dioxide, NbO.sub.2, with the molar ratio of niobium-containing vapor species to mercury in the fill being in the range of from about 0.01:1 to about 0.50:1; and mercury pressure of about 1 to about 50 atmospheres at lamp operating temperature. There is also provided a high intensity discharge device comprising a sealed light-transmissive arc tube; the arc tube including the above-described fill; and an energizing means for producing an electric discharge within the arc tube.

  4. Electrodeless HID lamp study. Final report. [High intensity discharge

    SciTech Connect (OSTI)

    Anderson, J.M.; Johnson, P.D.; Jones, C.E.; Rautenberg, T.H.

    1985-01-01T23:59:59.000Z

    High intensity discharge lamps excited by solenoidal electric fields (SEF/HID) were examined for their ability to give high brightness, high efficacy and good color. Frequency of operation was 13.56 MHz (ISM Band) and power to the lamp plasma ranged from about 400 to 1000 W. Radio frequency transformers with air cores and with air core complemented by ferrite material in the magnetic path were used to provide the voltage for excitation. Electrical properties of the matching network and the lamp plasma were measured or calculated and total light from the lamp was measured by an integrating sphere. Efficacies calculated from measurement were found to agree well with the positive column efficacies of conventional HID lamps containing only mercury, and with additives of sodium, thallium, and scandium iodide. Recommendations for future work are given.

  5. Light Emission of Argon Discharges: Importance of Heavy Particle Processes

    SciTech Connect (OSTI)

    Hartmann, Peter [Research Institute for Solid State Physics and Optics, Hungarian Academy of Sciences, POB 49, H-1525 Budapest (Hungary)

    2004-12-01T23:59:59.000Z

    Simulation studies on argon glow discharges established between flat disc electrodes, at pressure x electrode separation (pd) of 45 Pa cm are reported, with special attention to heavy-particle processes including excitation-induced light emission. The discharges are investigated through self-consistent hybrid modelling, consisting of a fluid description for components near local hydrodynamic equilibrium (slow electrons and ions), and Monte Carlo treatment of energetic electrons and heavy particles (ions and neutral atoms). The light emission profiles are analyzed for a wide range of operating conditions. The numerical results for the relative intensities and the shapes of the negative glow (created by electron impact excitation) and the cathode glow (created by heavy particle impact excitation) are in good agreement with experimental data obtained by Maric et al.

  6. Intensity-Intensity Correlations of Classically Entangled Light

    E-Print Network [OSTI]

    Partha Ghose; Anirban Mukherjee

    2014-01-03T23:59:59.000Z

    An experiment is proposed to show that after initial frequency and polarization selection, classical thermal light from two independent sources can be made path-polarization entangled. Such light will show new intensity-intensity correlations involving both path and polarization phases, formally similar to those for four-particle GHZ states. For fixed polarization phases, the correlations reduce to the Hanbury Brown-Twiss phase correlations. It is also shown that these classical correlations violate noncontextuality.

  7. Max Tech and Beyond: High-Intensity Discharge Lamps

    SciTech Connect (OSTI)

    Scholand, Michael

    2012-04-01T23:59:59.000Z

    High-intensity discharge (HID) lamps are most often found in industrial and commercial applications, and are the light source of choice in street and area lighting, and sports stadium illumination. HID lamps are produced in three types - mercury vapor (MV), high pressure sodium (HPS) and metal halide (MH). Of these, MV and MH are considered white-light sources (although the MV exhibits poor color rendering) and HPS produces a yellow-orange color light. A fourth lamp, low-pressure sodium (LPS), is not a HID lamp by definition, but it is used in similar applications and thus is often grouped with HID lamps. With the notable exception of MV which is comparatively inefficient and in decline in the US from both a sales and installed stock point of view; HPS, LPS and MH all have efficacies over 100 lumens per watt. The figure below presents the efficacy trends over time for commercially available HID lamps and LPS, starting with MV and LPS in 1930's followed by the development of HPS and MH in the 1960's. In HID lamps, light is generated by creating an electric arc between two electrodes in an arc tube. The particles in the arc are partially ionized, making them electrically conductive, and a light-emitting 'plasma' is created. This arc occurs within the arc tube, which for most HID lamps is enclosed within an evacuated outer bulb that thermally isolates and protects the hot arc tube from the surroundings. Unlike a fluorescent lamp that produces visible light through down-converting UV light with phosphors, the arc itself is the light source in an HID lamp, emitting visible radiation that is characteristic of the elements present in the plasma. Thus, the mixture of elements included in the arc tube is one critical factor determining the quality of the light emitted from the lamp, including its correlated color temperature (CCT) and color rendering index (CRI). Similar to fluorescent lamps, HID lamps require a ballast to start and maintain stable operating conditions, and this necessitates additional power beyond that used by the lamp itself. HID lamps offer important advantages compared to other lighting technologies, making them well suited for certain applications. HID lamps can be very efficient, have long operating lives, are relatively temperature-insensitive and produce a large quantity of light from a small package. For these reasons, HID lamps are often used when high levels of illumination are required over large areas and where operating and maintenance costs must be kept to a minimum. Furthermore, if the installation has a significant mounting height, high-power HID lamps can offer superior optical performance luminaires, reducing the number of lamps required to illuminate a given area. The indoor environments best suited to HID lamps are those with high ceilings, such as those commonly found in industrial spaces, warehouses, large retail spaces, sports halls and large public areas. Research into efficacy improvements for HID lighting technologies has generally followed market demand for these lamps, which is in decline for MV and LPS, has reached a plateau for HPS and is growing for MH. Several manufacturers interviewed for this study indicated that although solid-state lighting was now receiving the bulk of their company's R&D investment, there are still strong HID lamp research programs, which concentrate on MH technologies, with some limited amount of investment in HPS for specific niche applications (e.g., agricultural greenhouses). LPS and MV lamps are no longer being researched or improved in terms of efficacy or other performance attributes, although some consider MH HID lamps to be the next-generation MV lamp. Thus, the efficacy values of commercially available MV, LPS and HPS lamps are not expected to increase in the next 5 to 10 years. MH lamps, and more specifically, ceramic MH lamps are continuing to improve in efficacy as well as light quality, manufacturability and lamp life. Within an HID lamp, the light-producing plasma must be heated to sufficiently high temperatures to achieve high efficiencie

  8. Microwave power spectral density and its effects on exciting electrodeless high intensity discharge lamps

    SciTech Connect (OSTI)

    Butler, S.J.; Goss, H.H.; Lapatovich, W.P. [Osram Sylvania Inc., Salem, MA (United States)

    1995-12-31T23:59:59.000Z

    The effects of a microwave source generating a spectrally dense power spectrum on the operation of an electrodeless high intensity discharge lamp were measured. Spectrally pure sources operating within ISM bands at 915 MHz and 2.45 GHz produce stable capacitively coupled discharges useful for producing flicker-free light for numerous applications. The internal plasma temperature distribution and lamp geometry define acoustic resonance modes within the lamp which can be excited with power sidebands. The operation of lamps with commercially available power sources and custom built generators are discussed. Estimates of the spectral purity required for stable operation are provided.

  9. Techniques for optically compressing light intensity ranges

    DOE Patents [OSTI]

    Rushford, M.C.

    1989-03-28T23:59:59.000Z

    A pin hole camera assembly for use in viewing an object having a relatively large light intensity range, for example a crucible containing molten uranium in an atomic vapor laser isotope separator (AVLIS) system is disclosed herein. The assembly includes means for optically compressing the light intensity range appearing at its input sufficient to make it receivable and decipherable by a standard video camera. A number of different means for compressing the intensity range are disclosed. These include the use of photogray glass, the use of a pair of interference filters, and the utilization of a new liquid crystal notch filter in combination with an interference filter. 18 figs.

  10. Atlas of uranium emission intensities in a hollow cathode discharge

    SciTech Connect (OSTI)

    Palmer, B.A.; Keller, R.A.; Engleman, R. Jr.

    1980-07-01T23:59:59.000Z

    The uranium emission spectrum from a hollow cathode discharge is displayed from 11,000 to 26,000 cm/sup -1/. This atlas lists 4928 spectral lines of uranium; 3949 are classified to the neutral spectrum and 431 are classified to the singly ionized spectrum. Listed wavenumbers are accurate to +-0.003 cm/sup -1/ and the listed relative intensities to +-8%. The richness of the spectrum makes this atlas useful for wavenumber calibration of lasers, spectrographs, and monochromators to an accuracy of 1 part in 10/sup 7/. This atlas is also useful as a guide to the uranium spectrum, and relative oscillator strengths (gf values) can be calculated from the intensities to a precision of +-20%.

  11. Large area, surface discharge pumped, vacuum ultraviolet light source

    DOE Patents [OSTI]

    Sze, R.C.; Quigley, G.P.

    1996-12-17T23:59:59.000Z

    Large area, surface discharge pumped, vacuum ultraviolet (VUV) light source is disclosed. A contamination-free VUV light source having a 225 cm{sup 2} emission area in the 240-340 nm region of the electromagnetic spectrum with an average output power in this band of about 2 J/cm{sup 2} at a wall-plug efficiency of approximately 5% is described. Only ceramics and metal parts are employed in this surface discharge source. Because of the contamination-free, high photon energy and flux, and short pulse characteristics of the source, it is suitable for semiconductor and flat panel display material processing. 3 figs.

  12. Large area, surface discharge pumped, vacuum ultraviolet light source

    DOE Patents [OSTI]

    Sze, Robert C. (Santa Fe, NM); Quigley, Gerard P. (Los Alamos, NM)

    1996-01-01T23:59:59.000Z

    Large area, surface discharge pumped, vacuum ultraviolet (VUV) light source. A contamination-free VUV light source having a 225 cm.sup.2 emission area in the 240-340 nm region of the electromagnetic spectrum with an average output power in this band of about 2 J/cm.sup.2 at a wall-plug efficiency of approximately 5% is described. Only ceramics and metal parts are employed in this surface discharge source. Because of the contamination-free, high photon energy and flux, and short pulse characteristics of the source, it is suitable for semiconductor and flat panel display material processing.

  13. Measurement of Dynamic Light Scattering Intensity in Gels

    E-Print Network [OSTI]

    Rochas, Cyrille

    2015-01-01T23:59:59.000Z

    In the scientific literature little attention has been given to the use of dynamic light scattering (DLS) as a tool for extracting the thermodynamic information contained in the absolute intensity of light scattered by gels. In this article we show that DLS yields reliable measurements of the intensity of light scattered by the thermodynamic fluctuations, not only in aqueous polymer solutions, but also in hydrogels. In hydrogels, light scattered by osmotic fluctuations is heterodyned by that from static or slowly varying inhomogeneities. The two components are separable owing to their different time scales, giving good experimental agreement with macroscopic measurements of the osmotic pressure. DLS measurements in gels are, however, tributary to depolarised light scattering from the network as well as to multiple light scattering. The paper examines these effects, as well as the instrumental corrections required to determine the osmotic modulus. For guest polymers trapped in a hydrogel the measured intensity...

  14. High-Intensity Discharge Lighting Basics | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "ofEarly Career Scientists'Montana.ProgramJulietip sheetK-4In 2013 many| Department HIGHImage of

  15. Light Intensity-Dependent Modulation of Chlorophyll b Biosynthesis and Photosynthesis by Overexpression of

    E-Print Network [OSTI]

    Govindjee

    limiting and saturating light intensities. Although the quantum yield of carbon dioxide fixation remained carbon dioxide assimilation, starch content, and dry matter accumulation. Light intensity is a majorLight Intensity-Dependent Modulation of Chlorophyll b Biosynthesis and Photosynthesis

  16. Optical pumping in a microfabricated Rb vapor cell using a microfabricated Rb discharge light source

    SciTech Connect (OSTI)

    Venkatraman, V.; Kang, S.; Affolderbach, C.; Mileti, G., E-mail: gaetano.mileti@unine.ch [Laboratoire Temps-Fréquence, University of Neuchâtel, Neuchâtel 2000 (Switzerland); Shea, H. [Microsystems for Space Technologies Laboratory, Ecole Polytechnique Fédérale de Lausanne (EPFL), Neuchâtel 2002 (Switzerland)

    2014-02-03T23:59:59.000Z

    Miniature (light sources. Here, we report on the demonstration of optical pumping in a microfabricated alkali vapor resonance cell using (1) a microfabricated Rb discharge lamp light source, as well as (2) a conventional glass-blown Rb discharge lamp. The microfabricated Rb lamp cell is a dielectric barrier discharge (DBD) light source, having the same inner cell volume of around 40?mm{sup 3} as that of the resonance cell, both filled with suitable buffer gases. A miniature (?2?cm{sup 3} volume) test setup based on the M{sub z} magnetometer interrogation technique was used for observation of optical-radiofrequency double-resonance signals, proving the suitability of the microfabricated discharge lamp to introduce efficient optical pumping. The pumping ability of this light source was found to be comparable to or even better than that of a conventional glass-blown lamp. The reported results indicate that the micro-fabricated DBD discharge lamp has a high potential for the development of a new class of miniature atomic clocks, magnetometers, and quantum sensors.

  17. FLUORESCENCE CHANGES IN PORPHYRIDIUM EXPOSED TO GREEN LIGHT OF DIFFERENT INTENSITY: A NEW EMISSION

    E-Print Network [OSTI]

    Govindjee

    FLUORESCENCE CHANGES IN PORPHYRIDIUM EXPOSED TO GREEN LIGHT OF DIFFERENT INTENSITY: A NEW EMISSION supposed to require two light reactions for the transfer of one hydrogen atom from water to carbon dioxide the existence of this second trap. With increase in intensity of green light, I,, the differential fluorescence

  18. Development of large volume double ring penning plasma discharge source for efficient light emissions

    SciTech Connect (OSTI)

    Prakash, Ram; Vyas, Gheesa Lal; Jain, Jalaj; Prajapati, Jitendra; Pal, Udit Narayan [Microwave Tubes Division, CSIR-Central Electronics and Engineering Research Institute, Pilani-333031 (India); Chowdhuri, Malay Bikas; Manchanda, Ranjana [Institute for Plasma Research, Bhat, Gandhinagar-382428 (India)

    2012-12-15T23:59:59.000Z

    In this paper, the development of large volume double ring Penning plasma discharge source for efficient light emissions is reported. The developed Penning discharge source consists of two cylindrical end cathodes of stainless steel having radius 6 cm and a gap 5.5 cm between them, which are fitted in the top and bottom flanges of the vacuum chamber. Two stainless steel anode rings with thickness 0.4 cm and inner diameters 6.45 cm having separation 2 cm are kept at the discharge centre. Neodymium (Nd{sub 2}Fe{sub 14}B) permanent magnets are physically inserted behind the cathodes for producing nearly uniform magnetic field of {approx}0.1 T at the center. Experiments and simulations have been performed for single and double anode ring configurations using helium gas discharge, which infer that double ring configuration gives better light emissions in the large volume Penning plasma discharge arrangement. The optical emission spectroscopy measurements are used to complement the observations. The spectral line-ratio technique is utilized to determine the electron plasma density. The estimated electron plasma density in double ring plasma configuration is {approx}2 Multiplication-Sign 10{sup 11} cm{sup -3}, which is around one order of magnitude larger than that of single ring arrangement.

  19. 2014-05-05 Issuance: Test Procedures for High-Intensity Discharge...

    Broader source: Energy.gov (indexed) [DOE]

    Documents & Publications 2014-05-16 Issuance: Test Procedures for Integrated Light-Emitting Diode Lamps; Supplemental Notice of Proposed Rulemaking 2014-06-18 Issuance: Test...

  20. Fiber Bragg grating inscription by high-intensity femtosecond UV laser light: comparison

    E-Print Network [OSTI]

    Nikogosyan, David N.

    Fiber Bragg grating inscription by high-intensity femtosecond UV laser light: comparison with other 264-nm laser light and a phase mask technique, Bragg grating inscription in a range of different, that result in a significant photosensitivity enhancement of the in- vestigated fibers in comparison

  1. Note: Characterization of the plasma parameters of a capillary discharge-produced plasma channel waveguide to guide an intense laser pulse

    SciTech Connect (OSTI)

    Higashiguchi, Takeshi; Yugami, Noboru [Department of Advanced Interdisciplinary Sciences and Center for Optical Research and Education (CORE), Utsunomiya University, Yoto 7-1-2, Utsunomiya, Tochigi 321-8585 (Japan); CREST, Japan Science and Technology Agency, 4-1-8 Honcho, Kanagawa, Saitama 332-0012 (Japan); Hikida, Masafumi; Terauchi, Hiromitsu; Bai Jinxiang [Department of Advanced Interdisciplinary Sciences and Center for Optical Research and Education (CORE), Utsunomiya University, Yoto 7-1-2, Utsunomiya, Tochigi 321-8585 (Japan); Kikuchi, Takashi [Department of Electrical Engineering, Nagaoka University of Technology, Kami-tomiokamachi 1603-1, Nagaoka, Niigata 940-2188 (Japan); Tao Yezheng [Center for Energy Research, University of California, San Diego, 9500 Gilman Drive, La Jolla, California 92093-0438 (United States)

    2010-04-15T23:59:59.000Z

    We demonstrated the production of an optical waveguide in a capillary discharge-produced plasma using a cylindrical capillary. Plasma parameters of its waveguide were characterized by use of both a Nomarski laser interferometer and a hydrogen plasma line spectrum. A space-averaged maximum temperature of 3.3 eV with electron densities of the order of 10{sup 17} cm{sup -3} was observed at a discharge time of 150 ns and a maximum discharge current of 400 A. An ultrashort, intense laser pulse was guided by use of this plasma channel.

  2. Investigation of a moly-oxide electrodeless discharge for lighting applications

    SciTech Connect (OSTI)

    Giuliani, J.L.; Meger, R.A.; Pechacek, R.E.; Hinshelwood, D.D.; Shamamian, V.; Butler, J.E.

    1999-07-01T23:59:59.000Z

    Due to the hazardous material designation of spent fluorescent bulbs on board naval vessels, the Naval Research Laboratory has been investigating alternative lighting concepts which are free of mercury. The ideal goal is an efficient, large volume source, which provides white light directly without the use of a phosphor coating. Experiments with a {mu}wave plasma reactor normally used to diamond growth at {approximately}40 Torr revealed that a combination of O{sub 2}, N{sub 2}, and a heated molybdenum puck led to intense plasma emission in the visible domain. As the reactor was not designed for lighting studies, the authors have been investigating the process in glass tubes with a re-entry geometry and RF driven coils. Results will be presented on the initial discovery, the role of moly-oxide in surface evaporation, and the favorable emission spectrum of atomic molybdenum for visible light. Initial studies of the RF system, including coil design, measured electron density, B-dot measurements, E-to-H transitions, and spectroscopic analysis of various compositions will also be discussed. Finally, the essential problem of a recycling process for the moly emitters from the glass walls back to the moderate pressure plasma using chlorine will be addressed.

  3. Efficient Light Sources Today

    E-Print Network [OSTI]

    Hart, A. L.

    1982-01-01T23:59:59.000Z

    This paper reviews new lamp and lighting technology in terms of application and economic impact. Included are the latest advances in High Intensity Discharge systems, energy saving fluorescent lamps and ballasts, and the new state of the art high...

  4. Long lifetime, low intensity light source for use in nighttime viewing of equipment maps and other writings

    DOE Patents [OSTI]

    Frank, Alan M. (Livermore, CA); Edwards, William R. (Modesto, CA)

    1983-01-01T23:59:59.000Z

    A long-lifetime light source with sufficiently low intensity to be used for reading a map or other writing at nighttime, while not obscuring the user's normal night vision. This light source includes a diode electrically connected in series with a small power source and a lens properly positioned to focus at least a portion of the light produced by the diode.

  5. Coherent backscattering of intense light by cold atoms with degenerate energy levels: Diagrammatic treatment

    E-Print Network [OSTI]

    V. N. Shatokhin; R. Blattmann; T. Wellens; A. Buchleitner

    2014-07-10T23:59:59.000Z

    We present a generalization of the diagrammatic pump-probe approach to coherent backscattering (CBS) of intense laser light for atoms with degenerate energy levels. We employ this approach for a characterization of the double scattering signal from optically pumped atoms with the transition $J_g\\rightarrow J_e=J_g+1$ in the helicity preserving polarization channel. We show that, in the saturation regime, the internal degeneracy becomes manifest for atoms with $J_g\\geq 1$, leading to a faster decrease of the CBS enhancement factor with increasing saturation parameter than in the non-degenerate case.

  6. Asymptotic model for shape resonance control of diatomics by intense non-resonant light

    E-Print Network [OSTI]

    Anne Crubellier; Rosario González-Férez; Christiane P. Koch; Eliane Luc-Koenig

    2014-12-01T23:59:59.000Z

    We derive a universal model for atom pairs interacting with non-resonant light via the polarizability anisotropy, based on the long range properties of the scattering. The corresponding dynamics can be obtained using a nodal line technique to solve the asymptotic Schr\\"odinger equation. It consists in imposing physical boundary conditions at long range and vanishing of the wavefunction at a position separating inner zone and asymptotic region. We show that nodal lines which depend on the intensity of the non-resonant light can satisfactorily account for the effect of the polarizability at short range. The approach allows to determine the resonance structure, energy, width, channel mixing and hybridization even for narrow resonances.

  7. Lighting Options for Homes.

    SciTech Connect (OSTI)

    Baker, W.S.

    1991-04-01T23:59:59.000Z

    This report covers many aspects of various lighting options for homes. Types of light sources described include natural light, artificial light, incandescent lamps, fluorescent lamps, and high intensity discharge lamps. A light source selection guide gives the physical characteristics of these, design considerations, and common applications. Color, strategies for efficient lighting, and types of lighting are discussed. There is one section giving tips for various situations in specific rooms. Rooms and types of fixtures are shown on a matrix with watts saved by using the recommended type lighting for that room and room location. A major emphasis of this report is saving energy by utilizing the most suitable, recommended lighting option. (BN)

  8. Long lifetime, low intensity light source for use in nighttime viewing of equipment maps and other writings

    DOE Patents [OSTI]

    Frank, A.M.; Edwards, W.R.

    1983-10-11T23:59:59.000Z

    A long-lifetime light source with sufficiently low intensity to be used for reading a map or other writing at nighttime, while not obscuring the user's normal night vision is disclosed. This light source includes a diode electrically connected in series with a small power source and a lens properly positioned to focus at least a portion of the light produced by the diode. 1 fig.

  9. Long lifetime, low intensity light source for use in nighttime viewing of equipment maps and other writings

    DOE Patents [OSTI]

    Frank, A.M.; Edwards, W.R.

    1982-03-23T23:59:59.000Z

    A long-lifetime light source is discussed with sufficiently low intensity to be used for reading a map or other writing at nightime, while not obscuring the user's normal night vision. This light source includes a diode electrically connected in series with a small power source and a lens properly positioned to focus at least a portion of the light produced by the diode.

  10. The effect of a synthetic cytokinin, 6-benzylaminopurine, and light quality on Ficus benjamina under low light intensities

    E-Print Network [OSTI]

    Meadows, Sylvia Elise

    1979-01-01T23:59:59.000Z

    of artificial light sources, the effects of the different wavelengths have become more important, as artificial light sources do not emi t as wide a spectrum as does natural sunlight. Cool white fluorescent tubes have a high blue licht component, while i... higher dry weight gain than fluorescent plus tungsten plus mercury or fluorescent plus mercury, or fluor scent alone (23). Incandescent bulbs are high in infrared irradiation compared to fluorescent light sources, and it has been found that infrared 1r...

  11. System for obtaining smooth laser beams where intensity variations are reduced by spectral dispersion of the laser light (SSD)

    DOE Patents [OSTI]

    Skupsky, Stanley (Rochester, NY); Kessler, Terrance J. (Rochester, NY); Short, Robert W. (Rochester, NY); Craxton, Stephen (Rochester, NY); Letzring, Samuel A. (Honeoye Falls, NY); Soures, John (Pittsford, NY)

    1991-01-01T23:59:59.000Z

    In an SSD (smoothing by spectral dispersion) system which reduces the time-averaged spatial variations in intensity of the laser light to provide uniform illumination of a laser fusion target, an electro-optic phase modulator through which a laser beam passes produces a broadband output beam by imposing a frequency modulated bandwidth on the laser beam. A grating provides spatial and angular spectral dispersion of the beam. Due to the phase modulation, the frequencies ("colors") cycle across the beam. The dispersed beam may be amplified and frequency converted (e.g., tripled) in a plurality of beam lines. A distributed phase plate (DPP) in each line is irradiated by the spectrally dispersed beam and the beam is focused on the target where a smooth (uniform intensity) pattern is produced. The color cycling enhances smoothing and the use of a frequency modulated laser pulse prevents the formation of high intensity spikes which could damage the laser medium in the power amplifiers.

  12. Phase coherence in multiple scattering : weak and intense monochromatic light wave propagating in a cold strontium

    E-Print Network [OSTI]

    in a cold strontium cloud David Wilkowski, Yannick Bidel, Thierry Chaneli`ere, Robin Kaiser, Bruce Klappauf coherence of a monochromatic laser light propagating in an optically thick sample of laser-cooled strontium

  13. Arrangement for multiplexing and intensity splitting light beams for interface into fiber optic cables

    DOE Patents [OSTI]

    Johnson, Steve A. (Tracy, CA)

    1990-01-01T23:59:59.000Z

    An arrangement especially suitable for use in a laser apparatus for converting a plurality of different input light beams, for example copper vapor laser beams, into a plurality of substantially identical light beams is disclosed herein. This arrangement utilizes an optical mixing bar which is preferably integrally formed as a single unit and which includes a main body for mixing light therein, a flat input surface on one end of the main body, and a multi-faceted output face on the opposite end of the main body. This arrangement also includes means for directing the plurality of different input light beams onto the input face of the mixing base, whereby to cause the different beams to mix within the main body of the mixing bar and exit the latter from its multi-faceted output face as the desired plurality of substantially identical output beams.

  14. Modulating emission intensity of GaN-based green light emitting diodes on c-plane sapphire

    SciTech Connect (OSTI)

    Du, Chunhua; Ma, Ziguang; Zhou, Junming; Lu, Taiping; Jiang, Yang; Jia, Haiqiang; Liu, Wuming; Chen, Hong, E-mail: hchen@iphy.ac.cn [Key Laboratory for Renewable Energy, Beijing Key Laboratory for New Energy Materials and Devices, Beijing National Laboratory for Condense Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing 100190 (China)

    2014-04-14T23:59:59.000Z

    The asymmetric dual-wavelength (green/blue) coupled InGaN/GaN multiple quantum wells were proposed to modulate the green emission intensity. Electroluminescent measurements demonstrate the conspicuous increment of the green light intensity by decreasing the coupled barrier thickness. This was partly attributed to capture of more carriers when holes tunnel across the thinner barrier from the blue quantum wells, as a hole reservoir, to the green quantum wells. While lower effective barrier height of the blue quantum wells benefits improved hole transportation from p-GaN to the active region. Efficiency droop of the green quantum wells was partially alleviated due to the enhanced injection efficiency of holes.

  15. System for obtaining smooth laser beams where intensity variations are reduced by spectral dispersion of the laser light (SSD)

    DOE Patents [OSTI]

    Skupsky, S.; Kessler, T.J.; Short, R.W.; Craxton, S.; Letzring, S.A.; Soures, J.

    1991-09-10T23:59:59.000Z

    In an SSD (smoothing by spectral dispersion) system which reduces the time-averaged spatial variations in intensity of the laser light to provide uniform illumination of a laser fusion target, an electro-optic phase modulator through which a laser beam passes produces a broadband output beam by imposing a frequency modulated bandwidth on the laser beam. A grating provides spatial and angular spectral dispersion of the beam. Due to the phase modulation, the frequencies (''colors'') cycle across the beam. The dispersed beam may be amplified and frequency converted (e.g., tripled) in a plurality of beam lines. A distributed phase plate (DPP) in each line is irradiated by the spectrally dispersed beam and the beam is focused on the target where a smooth (uniform intensity) pattern is produced. The color cycling enhances smoothing and the use of a frequency modulated laser pulse prevents the formation of high intensity spikes which could damage the laser medium in the power amplifiers. 8 figures.

  16. LIPID PRODUCTION BY DUNALIELLA SALINA IN BATCH CULTURE: EFFECTS OF NITROGEN LIMITATION AND LIGHT INTENSITY

    SciTech Connect (OSTI)

    Weldy, C.S.; Huesemann, M.

    2007-01-01T23:59:59.000Z

    Atmospheric carbon dioxide (CO2) concentrations are increasing and may cause unknown deleterious environmental effects if left unchecked. The Intergovernmental Panel on Climate Change (IPCC) has predicted in its latest report a 2°C to 4°C increase in global temperatures even with the strictest CO2 mitigation practices. Global warming can be attributed in large part to the burning of carbon-based fossil fuels, as the concentration of atmospheric CO2 is directly related to the burning of fossil fuels. Biofuels which do not add CO2 to the atmosphere are presently generated primarily from terrestrial plants, i.e., ethanol from corn grain and biodiesel from soybean oil. The production of biofuels from terrestrial plants is severely limited by the availability of fertile land. Lipid production from microalgae and its corresponding biodiesel production have been studied since the late 1970s but large scale production has remained economically infeasible due to the large costs of sterile growing conditions required for many algal species. This study focuses on the potential of the halophilic microalgae species Dunaliella salina as a source of lipids and subsequent biodiesel production. The lipid production rates under high light and low light as well as nitrogen suffi cient and nitrogen defi cient culture conditions were compared for D. salina cultured in replicate photobioreactors. The results show (a) cellular lipid content ranging from 16 to 44% (wt), (b) a maximum culture lipid concentration of 450mg lipid/L, and (c) a maximum integrated lipid production rate of 46mg lipid/L culture*day. The high amount of lipids produced suggests that D. salina, which can be mass-cultured in non-sterile outdoor ponds, has strong potential to be an economically valuable source for renewable oil and biodiesel production.

  17. Metallic halide lights and lighting systems. (Latest citations from the US Patent Bibliographic file with exemplary claims). Published Search

    SciTech Connect (OSTI)

    Not Available

    1994-11-01T23:59:59.000Z

    The bibliography contains citations of selected patents concerning the design and operation of metallic halide lights and lighting systems. High pressure, high intensity, and low wattage discharge lamps are described. Citations discuss power sources, lamp life, lamp control circuits, thermal switches, and heat reflective coatings. Applications in sport stadium lighting, vehicle headlights, and crop-lighting are included. (Contains a minimum of 170 citations and includes a subject term index and title list.)

  18. High pressure discharges in cavities formed by microfabrication techniques

    SciTech Connect (OSTI)

    Khan, B.A.; Cammack, D.A.; Pinker, R.D.; Racz, J. [Philips Electronics North America Corporation, Philips Research, Briarcliff Manor, New York 10510 (United States)] [Philips Electronics North America Corporation, Philips Research, Briarcliff Manor, New York 10510 (United States)

    1997-07-01T23:59:59.000Z

    High pressure discharges are the basis of small high intensity light sources. In this work, we demonstrate the formation of high pressure discharges, in cavities formed by applying micromachining and integrated circuit techniques to quartz substrates. Cavities containing varying amounts of mercury and argon were fabricated to obtain high pressure discharges. A high pressure mercury discharge was formed in the electrodeless cavities by exciting them with a microwave source, operating at 2.45 GHz and in the electroded cavities by applying a dc voltage. The contraction of the discharge into a high pressure arc was observed. A broad emission spectrum due to self-absorption and collisions between excited atoms and normal atoms, typical of high pressure mercury discharges, was measured. The light output and efficacy increased with increasing pressure. The measured voltage was used to estimate the pressure within the electroded cavities, which is as high as 127 atm for one of the two cavities discussed in this work. Efficacies over 40 lumens per watt were obtained for the electrodeless cavities and over 50 scr(l)m/W for the electroded cavities. {copyright} {ital 1997 American Institute of Physics.}

  19. HYDROGEN PRODUCTION BY THE CYANOBACTERIUM PLECTONEMA BORYANUM: EFFECTS OF INITIAL NITRATE CONCENTRATION, LIGHT INTENSITY, AND INHIBITION OF PHOTOSYSTEM II BY DCMU

    SciTech Connect (OSTI)

    Carter, B.; Huesemann, M.

    2008-01-01T23:59:59.000Z

    The alarming rate at which atmospheric carbon dioxide levels are increasing due to the burning of fossil fuels will have incalculable consequences if disregarded. Fuel cells, a source of energy that does not add to carbon dioxide emissions, have become an important topic of study. Although signifi cant advances have been made related to fuel cells, the problem of cheap and renewable hydrogen production still remains. The cyanobacterium Plectonema boryanum has demonstrated potential as a resolution to this problem by producing hydrogen under nitrogen defi cient growing conditions. Plectonema boryanum cultures were tested in a series of experiments to determine the effects of light intensity, initial nitrate concentration, and photosystem II inhibitor DCMU (3-(3,4- dichlorophenyl)-1,1-dimethylurea) upon hydrogen production. Cultures were grown in sterile Chu. No. 10 medium within photobioreactors constantly illuminated by halogen lights. Because the enzyme responsible for hydrogen production is sensitive to oxygen, the medium was continuously sparged with argon/CO2 (99.7%/0.3% vol/vol) by gas dispersion tubes immersed in the culture. Hydrogen production was monitored by using a gas chromatograph equipped with a thermal conductivity detector. In the initial experiment, the effects of initial nitrate concentration were tested and results revealed cumulative hydrogen production was maximum at an initial nitrate concentration of 1 mM. A second experiment was then conducted at an initial nitrate concentration of 1 mM to determine the effects of light intensity at 50, 100, and 200 ?mole m-2 s-1. Cumulative hydrogen production increased with increasing light intensity. A fi nal experiment, conducted at an initial nitrate concentration of 2 mM, tested the effects of high light intensity at 200 and 400 ?mole m-2 s-1. Excessive light at 400 ?mole m-2 s-1 decreased cumulative hydrogen production. Based upon all experiments, cumulative hydrogen production rates were optimal at an initial nitrate concentration of 1 mM and a light intensity of 100 ?mole m-2 s-1. DCMU was shown in all experiments to severely decrease hydrogen production as time progressed. With the information acquired so far, future experiments with reducing substances could determine maximum rates of hydrogen production. If maximum hydrogen production rates proved to be large enough, Plectonema boryanum could be grown on an industrial scale to provide hydrogen gas as a renewable fuel.

  20. Interference-induced enhancement of intensity and energy of a multimode quantum optical field by a subwavelength array of coherent light sources

    E-Print Network [OSTI]

    S. V. Kukhlevsky

    2008-06-13T23:59:59.000Z

    Recently, we have showed a mechanism that could provide a great transmission enhancement of the light waves passed through subwavelength aperture arrays in thin metal films not by the plasmon-polariton waves, but by the constructive interference of diffracted waves (beams generated by the apertures) at the detector placed in the far-field zone. We now present a quantum reformulation of the model. The Hamiltonian describing the interference-induced enhancement of the intensity and energy of a multimode quantum optical field is derived. Such a field can be produced, for instance, by a subwavelength array of coherent light sources.

  1. Industrial Lighting Techniques and New Developments

    E-Print Network [OSTI]

    Colotti, M. A.

    families customarily categorized in three major groupings Incandescent, Fluorescent, and High Intensity Discharge sources. In the incandescent family, halogen capsule 'technology has led to many new general lighting sources the 90-Watt and 45-Watt... Par 38 lamps deliver the same light output in the beam as conventional 150- and 75-Watt incandescent Par sources while using 40\\ less wattage and maintaining lamp life. By reducing voltage to the filament in halogen ~apsule sources, lamps can...

  2. The intensive cage culture of channel catfish, Ictalurus punctatus (Rafinesque), in the intake and discharge canals of a steam electric generating station, Trinidad, Texas

    E-Print Network [OSTI]

    Murrell, John L

    1973-01-01T23:59:59.000Z

    June ? 8 June 2. 9 106. 8 9 June ? 15 June 16 June ? 22 June 2. 8 2. 7 124. 1 143. 6 23 June ? 25 June 26 June ? 29 June 30 June ? 27 July 28 July ? 22 Aug 23 Aug ? 31 Aug 1 Sep ? 1 Oct 2 Oct ? 16 Nov Totals 28 22 28 29 222 2. 5 2...Temperature and dissolved oxygen were taken 1 m below the surface; all other parameters were , 'measured at the surface. 40 ~ ~ ~ ~ ~ t ' ~ j + ~ t t ~ ~ \\ t4O ~ ~ ~ yt ~ 4 t ~ \\ ~ 30 ~ ~ 20 ts 'L ~ 10 5EP OCT NOV DEC as Power and Light Company...

  3. Rapid sintering of TiO{sub 2} photoelectrodes using intense pulsed white light for flexible dye-sensitized solar cells

    SciTech Connect (OSTI)

    Jin, Hwa-Young [Photo-Electronic Hybrids Research Center, Korea Institute of Science and Technology, Seoul 136-791 (Korea, Republic of); Department of Chemical and Biological Engineering, Korea University, 145, Anam-ro, Seongbuk-gu, Seoul 136-701 (Korea, Republic of); Kim, Jae-Yup; Ah Lee, Jin; Lee, Kwangsoo; Yoo, Kicheon; Lee, Doh-Kwon; Kim, BongSoo; Young Kim, Jin; Kim, Honggon; Jung Son, Hae [Photo-Electronic Hybrids Research Center, Korea Institute of Science and Technology, Seoul 136-791 (Korea, Republic of); Kim, Jihyun [Department of Chemical and Biological Engineering, Korea University, 145, Anam-ro, Seongbuk-gu, Seoul 136-701 (Korea, Republic of); Ah Lim, Jung, E-mail: jalim@kist.re.kr, E-mail: mjko@kist.re.kr [Interface Control Research Center, Future Convergence Research Division, Korea Institute of Science and Technology, Seoul 136-791 (Korea, Republic of); Jae Ko, Min, E-mail: jalim@kist.re.kr, E-mail: mjko@kist.re.kr [Photo-Electronic Hybrids Research Center, Korea Institute of Science and Technology, Seoul 136-791 (Korea, Republic of); Green School, Korea University, 145, Anam-ro, Seongbuk-gu, Seoul 136-701 (Korea, Republic of)

    2014-04-07T23:59:59.000Z

    Intense pulsed white light (IPWL) sintering was carried out at room temperature, which is suitable dye-sensitized solar cells (DSSCs) fabrication process on plastic substrates for the mass production. Five seconds irradiation of IPWL on TiO{sub 2} electrode significantly improves the photocurrent density and power conversion efficiency of DSSCs by more than 110% and 115%, respectively, compared to the DSSCs without IPWL treatment. These improvements were mainly attributed to the enhanced interconnection between the TiO{sub 2} nanoparticles induced by IPWL illumination, which is confirmed by the impedance spectra analysis.

  4. JOURNAL DE PHYSIQUE Colloque C6, supplment au no 11-12, Tome 33, Novembre-Dcembre 1972,page 239 ULTRASONIC LIGHT DIFFRACTION FOR THE CASE OF THE INTENSE

    E-Print Network [OSTI]

    Boyer, Edmond

    of intense laser light diffracted on an ultrasonic wave were made for carbon disulfide, carbon tetrachloride, carbon tetrachloride and benzene (results for nitroben- zene and carbon disulfide were already presented of intensity distribution of diffraction patterns for the following liquids : nitrobenzene, carbon disulfide

  5. Advances in Lighting

    E-Print Network [OSTI]

    Tumber, A. J.

    1981-01-01T23:59:59.000Z

    colour rendition. The quartz-halogen incandescent lam s operate at higher temperatures, and have a somewhat higher efficacy, but they are rarely used except for special applicati ns. 3-2 High Intensity Discharge Lamps. Mercury is the grandfather... of the H.I.D. lamps. Its blue-green light, has been used almost exclusively for streetlighti and, often with colour-improving phospho it is still being used in industrial and commercial applications. Reactor-type ballasted mercury lamps can now...

  6. Solid-state lighting technology perspective.

    SciTech Connect (OSTI)

    Tsao, Jeffrey Yeenien; Coltrin, Michael Elliott

    2006-08-01T23:59:59.000Z

    Solid-State Lighting (SSL) uses inorganic light-emitting diodes (LEDs) and organic light-emitting diodes (OLEDs) to convert electricity into light for illumination. SSL has the potential for enormous energy savings and accompanying environmental benefits if its promise of 50% (or greater) energy efficiencies can be achieved. This report provides a broad summary of the technologies that underlie SSL. The applications for SSL and potential impact on U.S. and world-wide energy consumption, and impact on the human visual experience are discussed. The properties of visible light and different technical metrics to characterize its properties are summarized. The many factors contributing to the capital and operating costs for SSL and traditional lighting sources (incandescent, fluorescent, and high-intensity discharge lamps) are discussed, with extrapolations for future SSL goals. The technologies underlying LEDs and OLEDs are also described, including current and possible alternative future technologies and some of the present limitations.

  7. Powerful glow discharge excilamp

    DOE Patents [OSTI]

    Tarasenko, Victor F. (Tomsk, RU); Panchenko, Aleksey N. (Tomsk, RU); Skakun, Victor S. (Tomsk, RU); Sosnin, Edward A. (Tomsk, RU); Wang, Francis T. (Danville, CA); Myers, Booth R. (Livermore, CA); Adamson, Martyn G. (Danville, CA)

    2002-01-01T23:59:59.000Z

    A powerful glow discharge lamp comprising two coaxial tubes, the outer tube being optically transparent, with a cathode and anode placed at opposite ends of the tubes, the space between the tubes being filled with working gas. The electrodes are made as cylindrical tumblers placed in line to one other in such a way that one end of the cathode is inserted into the inner tube, one end of the anode coaxially covers the end of the outer tube, the inner tube penetrating and extending through the anode. The increased electrodes' surface area increases glow discharge electron current and, correspondingly, average radiation power of discharge plasma. The inner tube contains at least one cooling liquid tube placed along the axis of the inner tube along the entire lamp length to provide cathode cooling. The anode has a circumferential heat extracting radiator which removes heat from the anode. The invention is related to lighting engineering and can be applied for realization of photostimulated processes under the action of powerful radiation in required spectral range.

  8. High intensity femtosecond enhancement cavities

    E-Print Network [OSTI]

    Abram, Gilberto

    2009-01-01T23:59:59.000Z

    To produce extreme ultraviolet radiation via high harmonic generation (HHG) in rare gases, light intensities in excess of 1014 W/cm 2 are required. Usually such high intensity are obtained by parametric amplification of ...

  9. Physics Today October 2004-Intense X-Shaped Pulses of Light Propaga... http://www.physicstoday.org/vol-57/iss-10/p25.shtml 2 of 6 4/14/2005 7:30 PM

    E-Print Network [OSTI]

    Lu, Jian-yu

    Propagate Without Spreading in Water and Other Dispersive Media The nonlinear interaction of light with matter can imbue optical pulses with surprising and potentially useful properties. It seems inevitable discovered they could send short, intense laser pulses through a transparent crystal of lithium triborate

  10. A low-cost optical sensing device based on paired emitter-detector light emitting diodes. Analytica Chimica Acta 2006

    E-Print Network [OSTI]

    King-tong Lau; Susan Baldwin; Roderick Shepherd; William J. Yerazunis; Shinichi Izuo; Satoshi Ueyama; Dermont Diamond; Emitter-detector Leds; King-tong Lau; Susan Baldwin; Roderick Shepherd; William J; Shinichi Izuo; Satoshi Ueyama; Dermot Diamond

    A low power, high sensitivity, very low cost light emitting diode (LED) based device for intensity based light measurements is described. In this approach, a reverse-biased LED functioning as a photodiode, is coupled with a second LED configured in conventional emission mode. A simple timer circuit measures how long (in us) it takes for the photocurrent generated on the detector LED to discharge its capacitance from logic 1(+5 V) to logic 0 (+1.7 V). The entire instrument provides an inherently digital output of light intensity measurements for a few cents. this light intensity dependent discharge process has been applied to measuring concentrations of coloured solutions and a mathematical model developed based on the Beer-Lambert Law.

  11. Wastewater Discharge Program (Maine)

    Broader source: Energy.gov [DOE]

    The wastewater discharge regulations require that a license be obtained for the discharge of wastewater to a stream, river, wetland, or lake of the state, or to the ocean. Typical discharges...

  12. Data Intensive

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Data Intensive Data Intensive Computing Pilot Program In 2014 NERSC is conducting its second and last round of allocations to projects in data intensive science. This pilot aims to...

  13. Mercury Lamps Recycling Fluorescent light-tubes, compact fluorescent bulbs, mercury and sodium vapor lamps, ultraviolet and

    E-Print Network [OSTI]

    Baker, Chris I.

    Mercury Lamps Recycling Fluorescent light-tubes, compact fluorescent bulbs, mercury and sodium vapor lamps, ultraviolet and HID (high-intensity discharge) lamps and all other mercury containing labeled for shipment to a recycling plant for mercury, glass and aluminum recovery. The beneficial re

  14. Oscillations in glow discharges

    E-Print Network [OSTI]

    Prickett, Tom

    1950-01-01T23:59:59.000Z

    OSCILLATIONS IN GLOW DISCHARGES A Dissertation By Tom Prickett, Jr. June 1950 Approved as to style and content by Chairman of Committee OSCILLATIONS IN GLOW DISCHARGES A Dissertation By Tom Prickett, Jr* June 1950 OSCILLATIONS IN GLOW... 1950 CONTENTS Introduction ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 1 I. Review of Plasma Oscillations in Gas Discharges ? . . 2 II. Review of Relaxation Processes in Gas Discharges ? . 13 III. Report of Laboratory Investigation...

  15. Energy distribution of nonequilibrium electrons and optical phonons in GaAs under band-to-band pumping by intense short pulses of light

    SciTech Connect (OSTI)

    Altybaev, G. S.; Kumekov, S. E., E-mail: skumekov@mail.ru; Mahmudov, A. A. [Satpaev Kazakh National Technical University (Kazakhstan)

    2009-03-15T23:59:59.000Z

    Deviation from the Fermi distribution of nonequilibrium electrons and distribution of 'hot' optical phonons in GaAs under band-to-band pumping by picosecond pulses of light are calculated.

  16. Intensive two-photon absorption induced decay pathway in a ZnO crystal: Impact of light-induced defect state

    SciTech Connect (OSTI)

    Li, Zhong-guo; Wei, Tai-Huei [Department of Physics, Harbin Institute of Technology, Harbin 15001 (China)] [Department of Physics, Harbin Institute of Technology, Harbin 15001 (China); Yang, Jun-yi [School of Physical Science and Technology, Soochow University, Suzhou 215006 (China)] [School of Physical Science and Technology, Soochow University, Suzhou 215006 (China); Song, Ying-lin, E-mail: ylsong@hit.edu.cn [Department of Physics, Harbin Institute of Technology, Harbin 15001 (China) [Department of Physics, Harbin Institute of Technology, Harbin 15001 (China); School of Physical Science and Technology, Soochow University, Suzhou 215006 (China)

    2013-12-16T23:59:59.000Z

    Using the pump-probe with phase object technique with 20 ps laser pulses at 532?nm, we investigated the carrier relaxation process subsequent to two-photon absorption (TPA) in ZnO. As a result, we found that an additional subnanosecond decay pathway is activated when the pump beam intensity surpasses 0.4?GW/cm{sup 2}. We attributed this intensity-dependent pathway to a TPA induced bulk defect state and our results demonstrate that this photo induced defect state has potential applications in ZnO based optoelectronic and spintronic devices.

  17. Direct Discharge Permit (Vermont)

    Broader source: Energy.gov [DOE]

    A direct discharge permit is required if a project involves the discharge of pollutants to state waters. For generation purposes, this involves the withdrawal of surface water for cooling purposes...

  18. Lighting energy management in industrial plants

    SciTech Connect (OSTI)

    Bachler, J.M.

    1982-06-01T23:59:59.000Z

    This paper provides some guidance to assist plant managers and engineers in managing their light energy problems. Incandescent, flourescent, and high-intensity discharge lamps are compared. Flourescent is still predominant, incandescent is not recommended-and HID is rapidly gaining favor. Lamp life and lumen depreciation must be determined. Light loss factors which are not recoverable are: luminaire ambient temperature, voltage to the luminaire, ballast factor, and luminaire surface dirt depreciation. Light loss factors which can be recovered by plant maintainence are: room surface dirt depreciation, lamp failures, lamp lumen depreciation, and luminaire dirt depreciation. A method to determine the savings that may result from group relamping versus spot replacement is given. Finally, energy management steps, to maximize performance, are listed.

  19. Compact light source performance in recessed type luminaires

    SciTech Connect (OSTI)

    Hammer, E.E.

    1998-11-01T23:59:59.000Z

    Photometric comparisons were made with an indoor, recessed, type luminaire using incandescent, high intensity discharge and compact fluorescent lamps. The test results show substantial performance advantages, as expected, for the discharge light sources where the efficacy gains can be in the order for 400% even when including the ballast losses associated with the discharge lamps. The candlepower distribution patterns emerging from these luminaries are also different from those associated with the baseline incandescent lamps, and which are in some ways, even more desirable from a uniformity of illuminance perspective. A section on fluorescent lamp starting is also included which describes a system having excellent starting characteristics in terms of electrode starting temperature (RH/RC technique), proper operating frequency to minimize unwanted IR interactions, and satisfactory current crest factor values to help insure life performance.

  20. Discharge lamp with reflective jacket

    DOE Patents [OSTI]

    MacLennan, Donald A. (Gaithersburg, MD); Turner, Brian P. (Damascus, MD); Kipling, Kent (Gaithersburg, MD)

    2001-01-01T23:59:59.000Z

    A discharge lamp includes an envelope, a fill which emits light when excited disposed in the envelope, a source of excitation power coupled to the fill to excite the fill and cause the fill to emit light, and a reflector disposed around the envelope and defining an opening, the reflector being configured to reflect some of the light emitted by the fill back into the fill while allowing some light to exit through the opening. The reflector may be made from a material having a similar thermal index of expansion as compared to the envelope and which is closely spaced to the envelope. The envelope material may be quartz and the reflector material may be either silica or alumina. The reflector may be formed as a jacket having a rigid structure which does not adhere to the envelope. The lamp may further include an optical clement spaced from the envelope and configured to reflect an unwanted component of light which exited the envelope back into the envelope through the opening in the reflector. Light which can be beneficially recaptured includes selected wavelength regions, a selected polarization, and selected angular components.

  1. The response of a capacitively coupled discharge to the formation of dust particles: Experiments and modeling

    SciTech Connect (OSTI)

    Denysenko, I.; Berndt, J.; Kovacevic, E.; Stefanovic, I.; Selenin, V.; Winter, J. [School of Physics and Technology, V. N. Karazin Kharkiv National University, Svobody sq. 4, 61077 Kharkiv (Ukraine); Institute of Experimental Physics II, Ruhr-University Bochum, D-44780 Bochum (Germany); Institute of Experimental Physics II, Ruhr-University Bochum, D-44780 Bochum, Germany and Institute of Physics, POB 57, 11001 Belgrade (Serbia and Montenegro); Institute of Experimental Physics II, Ruhr-University Bochum, D-44780 Bochum (Germany)

    2006-07-15T23:59:59.000Z

    The influence of dust particles on the properties of a capacitively coupled Ar-C{sub 2}H{sub 2} discharge is studied both experimentally and theoretically. The results of measurements of the intensity and spatial distribution of the emitted light, the line width of the fast component of H{sub {alpha}} line and of the electron density during the particle growth are presented. To analyze the experimental results a one-dimensional discharge model is developed. Using the model the effects of dust grains on the power absorption (taking into account stochastic and Ohmic heating in the plasma sheaths), the optical emission intensity profile, the sheath size, the rf electric field and on the energy of positive ions bombarding the electrodes are investigated. In particular, it is shown that the decrease of the power absorption in the sheaths of complex plasmas is due to the dependence of the stochastic and Ohmic heating in the plasma sheaths on the electron temperature and the current flowing across the discharge plates. The results of the calculations are compared with the available experimental data and found to be in good agreement.

  2. Modeling scattered intensity from microspheres in evanescent field

    E-Print Network [OSTI]

    Shah, Suhani Kiran

    2008-10-10T23:59:59.000Z

    of the total scattered light intensity on microsphere size accounts for the scattered intensity distribution in a polydisperse microsphere sample. Understanding this variation in the scattered light with microsphere size will allow improved characterization...

  3. Longitudinal discharge laser electrodes

    DOE Patents [OSTI]

    Warner, B.E.; Miller, J.L.; Ault, E.R.

    1994-08-23T23:59:59.000Z

    The improved longitudinal discharge laser electrode with IR baffle includes an electrode made up of washers spaced along the laser axis in order to form inter-washer spaces for hollow cathode discharge to take place and for IR radiation to be trapped. Additional IR baffles can be placed between the electrode ann the window. 2 figs.

  4. Ultraviolet-B radiation enhancement in dielectric barrier discharge based xenon chloride exciplex source by air

    SciTech Connect (OSTI)

    Gulati, P., E-mail: pgulati1512@gmail.com [CSIR-Central Electronics Engineering Research Institute (CSIR-CEERI), Pilani, Rajasthan-333031 (India); Department of Physics, Banasthali University, P.O. Banasthali Vidyapith, Rajasthan 304022 (India); Prakash, R.; Pal, U. N.; Kumar, M. [CSIR-Central Electronics Engineering Research Institute (CSIR-CEERI), Pilani, Rajasthan-333031 (India); Vyas, V. [Department of Physics, Banasthali University, P.O. Banasthali Vidyapith, Rajasthan 304022 (India)

    2014-07-07T23:59:59.000Z

    A single barrier dielectric barrier discharge tube of quartz with multi-strip Titanium-Gold (Ti-Au) coatings have been developed and utilized for ultraviolet-B (UV-B) radiation production peaking at wavelength 308?nm. The observed radiation at this wavelength has been examined for the mixtures of the Xenon together with chlorine and air admixtures. The gas mixture composition, chlorine gas content, total gas pressure, and air pressure dependency of the UV intensity, has been analyzed. It is found that the larger concentration of Cl{sub 2} deteriorates the performance of the developed source and around 2% Cl{sub 2} in this source produced optimum results. Furthermore, an addition of air in the xenon and chlorine working gas environment leads to achieve same intensity of UV-B light but at lower working gas pressure where significant amount of gas is air.

  5. Glow discharge detector

    DOE Patents [OSTI]

    Koo, Jackson C. (San Ramon, CA); Yu, Conrad M. (Antioch, CA)

    2002-01-01T23:59:59.000Z

    A highly sensitive electronic ion cell for the measurement of trace elements in He carrier gas which involves glow discharge. A constant wave (CW) glow discharge detector which is controlled through a biased resistor, can detect the change of electron density caused by impurities in the He carrier gas by many orders of magnitude larger than that caused by direct ionization or electron capture. The glow discharge detector utilizes a floating pseudo-electrode to form a probe in or near the plasma. By using this probe, the large variation of electron density due to trace amounts of impurities can be directly measured.

  6. Capacitor discharge pulse analysis.

    SciTech Connect (OSTI)

    Baker, Michael Sean; Griffiths, Stewart K.; Tanner, Danelle Mary

    2013-08-01T23:59:59.000Z

    Capacitors used in firing sets and other high discharge current applications are discharge tested to verify performance of the capacitor against the application requirements. Parameters such as capacitance, inductance, rise time, pulse width, peak current and current reversal must be verified to ensure that the capacitor will meet the application needs. This report summarizes an analysis performed on the discharge current data to extract these parameters by fitting a second-order system model to the discharge data and using this fit to determine the resulting performance metrics. Details of the theory and implementation are presented. Using the best-fit second-order system model to extract these metrics results in less sensitivity to noise in the measured data and allows for direct extraction of the total series resistance, inductance, and capacitance.

  7. VIRTUAL LIGHT: DIGITALLY-GENERATED LIGHTING FOR VIDEO CONFERENCING APPLICATIONS

    E-Print Network [OSTI]

    Fisher, Kathleen

    VIRTUAL LIGHT: DIGITALLY-GENERATED LIGHTING FOR VIDEO CONFERENCING APPLICATIONS Andrea Basso method to improve the lighting conditions of a real scene or video sequence. In particular we concentrate on modifying real light sources intensities and inserting virtual lights into a real scene viewed from a fixed

  8. Lighting affects appearance LightSource emits photons

    E-Print Network [OSTI]

    Jacobs, David

    1 Lighting affects appearance #12;2 LightSource emits photons Photons travel in a straight line). And then some reach the eye/camera. #12;3 Reflectance Model how objects reflect light. Model light sources Algorithms for computing Shading: computing intensities within polygons Determine what light strikes what

  9. Correlated-Intensity velocimeter for Arbitrary Reflector

    DOE Patents [OSTI]

    Wang, Zhehui (Los Alamos, NM); Luo, Shengnian (Los Alamos, NM); Barnes, Cris W. (Arlington, VA); Paul, Stephen F. (West Orange, NJ)

    2008-11-11T23:59:59.000Z

    A velocimetry apparatus and method comprising splitting incoming reflected laser light and directing the laser light into first and second arms, filtering the laser light with passband filters in the first and second arms, one having a positive passband slope and the other having a negative passband slope, and detecting the filtered laser light via light intensity detectors following the passband filters in the first and second arms

  10. Max Tech and Beyond: High-Intensity Discharge Lamps

    E-Print Network [OSTI]

    Scholand, Michael

    2012-01-01T23:59:59.000Z

    Ceravision (UK), LG Electronics (South Korea) and Luxim (Milton Keynes, UK), LG Electronics (Seoul, South Korea) andwww.ceravision.com/Page/Home LG Electronics purchased the

  11. Very high efficacy electrodeless high intensity discharge lamps

    SciTech Connect (OSTI)

    Johnson, P.D.

    1987-11-10T23:59:59.000Z

    This patent describes an electrodeless arc lamp for forming a ring shaped plasma in a region therein during operation comprising a tube having a raised bottom center section, and an optically transparent outer jacket hermetically sealing the tube to protect the tube from cooling by convection. The raised center section rises centrally to form a ring shaped reservoir below the region in which the rig shaped plasma is formed to minimize wall cooling during operation of the lamp so that there is enhanced excitation near the center of the tube.

  12. Very high efficacy electrodeless high intensity discharge lamps

    DOE Patents [OSTI]

    Johnson, P.D.

    1985-10-03T23:59:59.000Z

    An electrodeless arc lamp comprises an outer jacket hermetically sealing and thermally protecting an arc tube inside which has an upwardly convex bottom center section. The absence of chemically reactive electrode material makes it possible to use metal halides other than iodides. The tube contains chlorides, bromides or a mixture thereof of scandium and sodium in a nearly equimolar relationship in addition to mercury and an inert gas. Good color balance can be obtained at reduced reservoir temperature and with less power loss. Reduction in wall temperature makes it possible to attain longer lamp life.

  13. Very high efficacy electrodeless high intensity discharge lamps

    DOE Patents [OSTI]

    Johnson, Peter D. (Schenectady, NY)

    1987-01-01T23:59:59.000Z

    An electrodeless arc lamp comprises an outer jacket hermetically sealing and thermally protecting an arc tube inside which has an upwardly convex bottom center section. The absence of chemically reactive electrode material makes it possible to use metal halides other than iodides. The tube contains chlorides, bromides or a mixture thereof of scandium and sodium in a nearly equimolar relationship in addition to mercury and an inert gas. Good color balance can be obtained at reduced reservoir temperature and with less power loss. Reduction in wall temperature makes it possible to attain longer lamp life.

  14. Max Tech and Beyond: High-Intensity Discharge Lamps

    E-Print Network [OSTI]

    Scholand, Michael

    2012-01-01T23:59:59.000Z

    of color compared with the incandescent reference source isin this report. Standard Incandescent Halogen Low-Pressure:value equivalent to an incandescent filament lamp. Taking

  15. A SPICE Compatible Model of High Intensity Discharge Lamps

    E-Print Network [OSTI]

    from the arc's * Corresponding author behavior of HID lamps. This model are derived from the arc-linear resistance of the lamp, is the global specific conductance of the plasma, V is the volume of the plasma, L is the length of plasma and S is the cross section. ~ Vin G1 Lamp Model Ballast v(lamp) i(lamp) Analytical

  16. 2011 Intensity -1 INTENSITY OF SOUND

    E-Print Network [OSTI]

    Glashausser, Charles

    the rate at which energy is passing a certain point. This concept involves sound intensity. Consider the sound intensity. Recall the time rate of energy transfer is called "power". Thus, sound intensity2011 Intensity - 1 INTENSITY OF SOUND The objectives of this experiment are: · To understand

  17. Plasma mixing glow discharge device for analytical applications

    DOE Patents [OSTI]

    Pinnaduwage, L.A.

    1999-04-20T23:59:59.000Z

    An instrument for analyzing a sample has an enclosure that forms a chamber containing an anode which divides the chamber into a discharge region and an analysis region. A gas inlet and outlet are provided to introduce and exhaust a rare gas into the discharge region. A cathode within the discharge region has a plurality of pins projecting in a geometric pattern toward the anode for exciting the gas and producing a plasma discharge between the cathode and the anode. Low energy electrons (e.g. <0.5 eV) pass into the analysis region through an aperture. The sample to be analyzed is placed into the analysis region and bombarded by the metastable rare gas atoms and the low energy electrons extracted into from the discharge region. A mass or optical spectrometer can be coupled to a port of the analysis region to analyze the resulting ions and light emission. 3 figs.

  18. Plasma mixing glow discharge device for analytical applications

    DOE Patents [OSTI]

    Pinnaduwage, Lal A. (Knoxville, TN)

    1999-01-01T23:59:59.000Z

    An instrument for analyzing a sample has an enclosure that forms a chamber containing an anode which divides the chamber into a discharge region and an analysis region. A gas inlet and outlet are provided to introduce and exhaust a rare gas into the discharge region. A cathode within the discharge region has a plurality of pins projecting in a geometric pattern toward the anode for exciting the gas and producing a plasma discharge between the cathode and the anode. Low energy electrons (e.g. <0.5 eV) pass into the analysis region through an aperture. The sample to be analyzed is placed into the analysis region and bombarded by the metastable rare gas atoms and the low energy electrons extracted into from the discharge region. A mass or optical spectrometer can be coupled to a port of the analysis region to analyze the resulting ions and light emission.

  19. Longitudinal discharge laser baffles

    DOE Patents [OSTI]

    Warner, B.E.; Ault, E.R.

    1994-06-07T23:59:59.000Z

    The IR baffles placed between the window and the electrode of a longitudinal discharge laser improve laser performance by intercepting off-axis IR radiation from the laser and in doing so reduce window heating and subsequent optical distortion of the laser beam. 1 fig.

  20. Lighting affects appearance LightSource emits photons

    E-Print Network [OSTI]

    Jacobs, David

    1 Lighting affects appearance #12;2 LightSource emits photons Photons travel in a straight line). And then some reach the eye/camera. #12;3 Basic fact: Light is linear Double intensity of sources, double photons reaching eye. Turn on two lights, and photons reaching eye are same as sum of number when each

  1. Water Pollutant Discharge Act (Illinois)

    Broader source: Energy.gov [DOE]

    The discharge of oil in quantities which exceed the standards adopted by the Pollution Control Board, or the discharge of other pollutants directly or indirectly into the waters is prohibited....

  2. National Synchrotron Light Source

    ScienceCinema (OSTI)

    None

    2010-01-08T23:59:59.000Z

    A tour of Brookhaven's National Synchrotron Light Source (NSLS). The NSLS is one of the world's most widely used scientific research facilities, hosting more than 2,500 guest researchers each year. The NSLS provides intense beams of infrared, ultraviole

  3. Computational phase imaging based on intensity transport

    E-Print Network [OSTI]

    Waller, Laura A. (Laura Ann)

    2010-01-01T23:59:59.000Z

    Light is a wave, having both an amplitude and a phase. However, optical frequencies are too high to allow direct detection of phase; thus, our eyes and cameras see only real values - intensity. Phase carries important ...

  4. Solid-state lighting : lamp targets and implications for the semiconductor chip.

    SciTech Connect (OSTI)

    Tsao, Jeffrey Yeenien

    2003-08-01T23:59:59.000Z

    A quiet revolution is underway. Over the next 5-10 years inorganic-semiconductor-based solid-state lighting technology is expected to outperform first incandescent, and then fluorescent and high-intensity-discharge, lighting. Along the way, many decision points and technical challenges will be faced. To help understand these challenges, the U.S. Department of Energy, the Optoelectronics Industry Development Association and the National Electrical Manufacturers Association recently updated the U.S. Solid-State Lighting Roadmap. In the first half of this paper, we present an overview of the high-level targets of the inorganic-semiconductor part of that update. In the second half of this paper, we discuss some implications of those high-level targets on the GaN-based semiconductor chips that will be the 'engine' for solid-state lighting.

  5. Fundamental Physics at the Intensity Frontier

    E-Print Network [OSTI]

    J. L. Hewett; H. Weerts; R. Brock; J. N. Butler; B. C. K. Casey; J. Collar; A. de Gouvea; R. Essig; Y. Grossman; W. Haxton; J. A. Jaros; C. K. Jung; Z. T. Lu; K. Pitts; Z. Ligeti; J. R. Patterson; M. Ramsey-Musolf; J. L. Ritchie; A. Roodman; K. Scholberg; C. E. M. Wagner; G. P. Zeller; S. Aefsky; A. Afanasev; K. Agashe; C. Albright; J. Alonso; C. Ankenbrandt; M. Aoki; C. A. Arguelles; N. Arkani-Hamed; J. R. Armendariz; C. Armendariz-Picon; E. Arrieta Diaz; J. Asaadi; D. M. Asner; K. S. Babu; K. Bailey; O. Baker; B. Balantekin; B. Baller; M. Bass; B. Batell; J. Beacham; J. Behr; N. Berger; M. Bergevin; E. Berman; R. Bernstein; A. J. Bevan; M. Bishai; M. Blanke; S. Blessing; A. Blondel; T. Blum; G. Bock; A. Bodek; G. Bonvicini; F. Bossi; J. Boyce; R. Breedon; M. Breidenbach; S. J. Brice; R. A. Briere; S. Brodsky; C. Bromberg; A. Bross; T. E. Browder; D. A. Bryman; M. Buckley; R. Burnstein; E. Caden; P. Campana; R. Carlini; G. Carosi; C. Castromonte; R. Cenci; I. Chakaberia; M. C. Chen; C. H. Cheng; B. Choudhary; N. H. Christ; E. Christensen; M. E. Christy; T. E. Chupp; E. Church; D. B. Cline; T. E. Coan; P. Coloma; J. Comfort; L. Coney; J. Cooper; R. J. Cooper; R. Cowan; D. F. Cowen; D. Cronin-Hennessy; A. Datta; G. S. Davies; M. Demarteau; D. P. DeMille; A. Denig; R. Dermisek; A. Deshpande; M. S. Dewey; R. Dharmapalan; J. Dhooghe; M. R. Dietrich; M. Diwan; Z. Djurcic; S. Dobbs; M. Duraisamy; B. Dutta; H. Duyang; D. A. Dwyer; M. Eads; B. Echenard; S. R. Elliott; C. Escobar; J. Fajans; S. Farooq; C. Faroughy; J. E. Fast; B. Feinberg; J. Felde; G. Feldman; P. Fierlinger; P. Fileviez Perez; B. Filippone; P. Fisher; B. T. Flemming; K. T. Flood; R. Forty; M. J. Frank; A. Freyberger; A. Friedland; R. Gandhi; K. S. Ganezer; A. Garcia; F. G. Garcia; S. Gardner; L. Garrison; A. Gasparian; S. Geer; V. M. Gehman; T. Gershon; M. Gilchriese; C. Ginsberg; I. Gogoladze; M. Gonderinger; M. Goodman; H. Gould; M. Graham; P. W. Graham; R. Gran; J. Grange; G. Gratta; J. P. Green; H. Greenlee; R. C. Group; E. Guardincerri; V. Gudkov; R. Guenette; A. Haas; A. Hahn; T. Han; T. Handler; J. C. Hardy; R. Harnik; D. A. Harris; F. A. Harris; P. G. Harris; J. Hartnett; B. He; B. R. Heckel; K. M. Heeger; S. Henderson; D. Hertzog; R. Hill; E. A Hinds; D. G. Hitlin; R. J. Holt; N. Holtkamp; G. Horton-Smith; P. Huber; W. Huelsnitz; J. Imber; I. Irastorza; J. Jaeckel; I. Jaegle; C. James; A. Jawahery; D. Jensen; C. P. Jessop; B. Jones; H. Jostlein; T. Junk; A. L. Kagan; M. Kalita; Y. Kamyshkov; D. M. Kaplan; G. Karagiorgi; A. Karle; T. Katori; B. Kayser; R. Kephart; S. Kettell; Y. K. Kim; M. Kirby; K. Kirch; J. Klein; J. Kneller; A. Kobach; M. Kohl; J. Kopp; M. Kordosky; W. Korsch; I. Kourbanis; A. D. Krisch; P. Krizan; A. S. Kronfeld; S. Kulkarni; K. S. Kumar; Y. Kuno; T. Kutter; T. Lachenmaier; M. Lamm; J. Lancaster; M. Lancaster; C. Lane; K. Lang; P. Langacker; S. Lazarevic; T. Le; K. Lee; K. T. Lesko; Y. Li; M. Lindgren; A. Lindner; J. Link; D. Lissauer; L. S. Littenberg; B. Littlejohn; C. Y. Liu; W. Loinaz; W. Lorenzon; W. C. Louis; J. Lozier; L. Ludovici; L. Lueking; C. Lunardini; D. B. MacFarlane; P. A. N. Machado; P. B. Mackenzie; J. Maloney; W. J. Marciano; W. Marsh; M. Marshak; J. W. Martin; C. Mauger; K. S. McFarland; C. McGrew; G. McLaughlin; D. McKeen; R. McKeown; B. T. Meadows; R. Mehdiyev; D. Melconian; H. Merkel; M. Messier; J. P. Miller; G. Mills; U. K. Minamisono; S. R. Mishra; I. Mocioiu; S. Moed Sher; R. N. Mohapatra; B. Monreal; C. D. Moore; J. G. Morfin; J. Mousseau; L. A. Moustakas; G. Mueller; P. Mueller; M. Muether; H. P. Mumm; C. Munger; H. Murayama; P. Nath; O. Naviliat-Cuncin; J. K. Nelson; D. Neuffer; J. S. Nico; A. Norman; D. Nygren; Y. Obayashi; T. P. O'Connor; Y. Okada; J. Olsen; L. Orozco; J. L. Orrell; J. Osta; B. Pahlka; J. Paley; V. Papadimitriou; M. Papucci; S. Parke; R. H. Parker; Z. Parsa; K. Partyka; A. Patch; J. C. Pati; R. B. Patterson; Z. Pavlovic; G. Paz; G. N. Perdue; D. Perevalov; G. Perez; R. Petti; W. Pettus; A. Piepke; M. Pivovaroff; R. Plunkett; C. C. Polly; M. Pospelov; R. Povey; A. Prakesh; M. V. Purohit; S. Raby; J. L. Raaf; R. Rajendran; S. Rajendran; G. Rameika; R. Ramsey; A. Rashed; B. N. Ratcliff; B. Rebel; J. Redondo; P. Reimer; D. Reitzner; F. Ringer; A. Ringwald; S. Riordan; B. L. Roberts; D. A. Roberts; R. Robertson; F. Robicheaux; M. Rominsky; R. Roser; J. L. Rosner; C. Rott; P. Rubin; N. Saito; M. Sanchez; S. Sarkar; H. Schellman; B. Schmidt; M. Schmitt; D. W. Schmitz; J. Schneps; A. Schopper; P. Schuster; A. J. Schwartz; M. Schwarz; J. Seeman; Y. K. Semertzidis; K. K. Seth; Q. Shafi; P. Shanahan; R. Sharma; S. R. Sharpe; M. Shiozawa; V. Shiltsev; K. Sigurdson; P. Sikivie; J. Singh; D. Sivers; T. Skwarnicki; N. Smith; J. Sobczyk; H. Sobel; M. Soderberg; Y. H. Song; A. Soni; P. Souder; A. Sousa; J. Spitz; M. Stancari; G. C. Stavenga; J. H. Steffen

    2012-05-11T23:59:59.000Z

    The Proceedings of the 2011 workshop on Fundamental Physics at the Intensity Frontier. Science opportunities at the intensity frontier are identified and described in the areas of heavy quarks, charged leptons, neutrinos, proton decay, new light weakly-coupled particles, and nucleons, nuclei, and atoms.

  6. Fundamental Physics at the Intensity Frontier

    E-Print Network [OSTI]

    Hewett, J L; Brock, R; Butler, J N; Casey, B C K; Collar, J; de Gouvea, A; Essig, R; Grossman, Y; Haxton, W; Jaros, J A; Jung, C K; Lu, Z T; Pitts, K; Ligeti, Z; Patterson, J R; Ramsey-Musolf, M; Ritchie, J L; Roodman, A; Scholberg, K; Wagner, C E M; Zeller, G P; Aefsky, S; Afanasev, A; Agashe, K; Albright, C; Alonso, J; Ankenbrandt, C; Aoki, M; Arguelles, C A; Arkani-Hamed, N; Armendariz, J R; Armendariz-Picon, C; Diaz, E Arrieta; Asaadi, J; Asner, D M; Babu, K S; Bailey, K; Baker, O; Balantekin, B; Baller, B; Bass, M; Batell, B; Beacham, J; Behr, J; Berger, N; Bergevin, M; Berman, E; Bernstein, R; Bevan, A J; Bishai, M; Blanke, M; Blessing, S; Blondel, A; Blum, T; Bock, G; Bodek, A; Bonvicini, G; Bossi, F; Boyce, J; Breedon, R; Breidenbach, M; Brice, S J; Briere, R A; Brodsky, S; Bromberg, C; Bross, A; Browder, T E; Bryman, D A; Buckley, M; Burnstein, R; Caden, E; Campana, P; Carlini, R; Carosi, G; Castromonte, C; Cenci, R; Chakaberia, I; Chen, M C; Cheng, C H; Choudhary, B; Christ, N H; Christensen, E; Christy, M E; Chupp, T E; Church, E; Cline, D B; Coan, T E; Coloma, P; Comfort, J; Coney, L; Cooper, J; Cooper, R J; Cowan, R; Cowen, D F; Cronin-Hennessy, D; Datta, A; Davies, G S; Demarteau, M; DeMille, D P; Denig, A; Dermisek, R; Deshpande, A; Dewey, M S; Dharmapalan, R; Dhooghe, J; Dietrich, M R; Diwan, M; Djurcic, Z; Dobbs, S; Duraisamy, M; Dutta, B; Duyang, H; Dwyer, D A; Eads, M; Echenard, B; Elliott, S R; Escobar, C; Fajans, J; Farooq, S; Faroughy, C; Fast, J E; Feinberg, B; Felde, J; Feldman, G; Fierlinger, P; Perez, P Fileviez; Filippone, B; Fisher, P; Flemming, B T; Flood, K T; Forty, R; Frank, M J; Freyberger, A; Friedland, A; Gandhi, R; Ganezer, K S; Garcia, A; Garcia, F G; Gardner, S; Garrison, L; Gasparian, A; Geer, S; Gehman, V M; Gershon, T; Gilchriese, M; Ginsberg, C; Gogoladze, I; Gonderinger, M; Goodman, M; Gould, H; Graham, M; Graham, P W; Gran, R; Grange, J; Gratta, G; Green, J P; Greenlee, H; Guardincerri, E; Gudkov, V; Guenette, R; Haas, A; Hahn, A; Han, T; Handler, T; Hardy, J C; Harnik, R; Harris, D A; Harris, F A; Harris, P G; Hartnett, J; He, B; Heckel, B R; Heeger, K M; Henderson, S; Hertzog, D; Hill, R; Hinds, E A; Hitlin, D G; Holt, R J; Holtkamp, N; Horton-Smith, G; Huber, P; Huelsnitz, W; Imber, J; Irastorza, I; Jaeckel, J; Jaegle, I; James, C; Jawahery, A; Jensen, D; Jessop, C P; Jones, B; Jostlein, H; Junk, T; Kagan, A L; Kalita, M; Kamyshkov, Y; Kaplan, D M; Karagiorgi, G; Karle, A; Katori, T; Kayser, B; Kephart, R; Kettell, S; Kim, Y K; Kirby, M; Kirch, K; Klein, J; Kneller, J; Kobach, A; Kohl, M; Kopp, J; Kordosky, M; Korsch, W; Kourbanis, I; Krisch, A D; Krizan, P; Kronfeld, A S; Kulkarni, S; Kumar, K S; Kuno, Y; Kutter, T; Lachenmaier, T; Lamm, M; Lancaster, J; Lancaster, M; Lane, C; Lang, K; Langacker, P; Lazarevic, S; Le, T; Lee, K; Lesko, K T; Li, Y; Lindgren, M; Lindner, A; Link, J; Lissauer, D; Littenberg, L S; Littlejohn, B; Liu, C Y; Loinaz, W; Lorenzon, W; Louis, W C; Lozier, J; Ludovici, L; Lueking, L; Lunardini, C; MacFarlane, D B; Machado, P A N; Mackenzie, P B; Maloney, J; Marciano, W J; Marsh, W; Marshak, M; Martin, J W; Mauger, C; McFarland, K S; McGrew, C; McLaughlin, G; McKeen, D; McKeown, R; Meadows, B T; Mehdiyev, R; Melconian, D; Merkel, H; Messier, M; Miller, J P; Mills, G; Minamisono, U K; Mishra, S R; Mocioiu, I; Sher, S Moed; Mohapatra, R N; Monreal, B; Moore, C D; Morfin, J G; Mousseau, J; Moustakas, L A; Mueller, G; Mueller, P; Muether, M; Mumm, H P; Munger, C; Murayama, H; Nath, P; Naviliat-Cuncin, O; Nelson, J K; Neuffer, D; Nico, J S; Norman, A; Nygren, D; Obayashi, Y; O'Connor, T P; Okada, Y; Olsen, J; Orozco, L; Orrell, J L; Osta, J; Pahlka, B; Paley, J; Papadimitriou, V; Papucci, M; Parke, S; Parker, R H; Parsa, Z; Partyka, K; Patch, A; Pati, J C; Patterson, R B; Pavlovic, Z; Paz, G; Perdue, G N; Perevalov, D; Perez, G; Petti, R; Pettus, W; Piepke, A; Pivovaroff, M; Plunkett, R; Polly, C C; Pospelov, M; Povey, R; Prakesh, A; Purohit, M V; Raby, S; Raaf, J L; Rajendran, R; Rajendran, S; Rameika, G; Ramsey, R; Rashed, A; Ratcliff, B N; Rebel, B; Redondo, J; Reimer, P; Reitzner, D; Ringer, F; Ringwald, A; Riordan, S; Roberts, B L; Roberts, D A; Robertson, R; Robicheaux, F; Rominsky, M; Roser, R; Rosner, J L; Rott, C; Rubin, P; Saito, N; Sanchez, M; Sarkar, S; Schellman, H; Schmidt, B; Schmitt, M; Schmitz, D W; Schneps, J; Schopper, A; Schuster, P; Schwartz, A J; Schwarz, M; Seeman, J; Semertzidis, Y K; Seth, K K; Shafi, Q; Shanahan, P; Sharma, R; Sharpe, S R; Shiozawa, M; Shiltsev, V; Sigurdson, K; Sikivie, P; Singh, J; Sivers, D; Skwarnicki, T; Smith, N; Sobczyk, J; Sobel, H; Soderberg, M; Song, Y H; Soni, A; Souder, P; Sousa, A; Spitz, J; Stancari, M; Stavenga, G C; Steffen, J H; Stepanyan, S; Stoeckinger, D; Stone, S; Strait, J; Strassler, M; Sulai, I A; Sundrum, R; Svoboda, R; Szczerbinska, B; Szelc, A; Takeuchi, T; Tanedo, P

    2012-01-01T23:59:59.000Z

    The Proceedings of the 2011 workshop on Fundamental Physics at the Intensity Frontier. Science opportunities at the intensity frontier are identified and described in the areas of heavy quarks, charged leptons, neutrinos, proton decay, new light weakly-coupled particles, and nucleons, nuclei, and atoms.

  7. Explosively pumped laser light

    DOE Patents [OSTI]

    Piltch, Martin S. (Los Alamos, NM); Michelotti, Roy A. (Los Alamos, NM)

    1991-01-01T23:59:59.000Z

    A single shot laser pumped by detonation of an explosive in a shell casing. The shock wave from detonation of the explosive causes a rare gas to luminesce. The high intensity light from the gas enters a lasing medium, which thereafter outputs a pulse of laser light to disable optical sensors and personnel.

  8. Large discharge-volume, silent discharge spark plug

    DOE Patents [OSTI]

    Kang, Michael (Los Alamos, NM)

    1995-01-01T23:59:59.000Z

    A large discharge-volume spark plug for providing self-limiting microdischarges. The apparatus includes a generally spark plug-shaped arrangement of a pair of electrodes, where either of the two coaxial electrodes is substantially shielded by a dielectric barrier from a direct discharge from the other electrode, the unshielded electrode and the dielectric barrier forming an annular volume in which self-terminating microdischarges occur when alternating high voltage is applied to the center electrode. The large area over which the discharges occur, and the large number of possible discharges within the period of an engine cycle, make the present silent discharge plasma spark plug suitable for use as an ignition source for engines. In the situation, where a single discharge is effective in causing ignition of the combustible gases, a conventional single-polarity, single-pulse, spark plug voltage supply may be used.

  9. National Synchrotron Light Source

    ScienceCinema (OSTI)

    BNL

    2009-09-01T23:59:59.000Z

    A tour of Brookhaven's National Synchrotron Light Source (NSLS), hosted by Associate Laboratory Director for Light Sources, Stephen Dierker. The NSLS is one of the world's most widely used scientific research facilities, hosting more than 2,500 guest researchers each year. The NSLS provides intense beams of infrared, ultraviolet, and x-ray light for basic and applied research in physics, chemistry, medicine, geophysics, environmental, and materials sciences.

  10. Observation and numerical analysis of plasma parameters in a capillary discharge-produced plasma channel waveguide

    SciTech Connect (OSTI)

    Terauchi, Hiromitsu [Department of Advanced Interdisciplinary Sciences, and Center for Optical Research and Education (CORE) Utsunomiya University, Yoto 7-1-2, Utsunomiya, Tochigi 321-8585 (Japan); Bobrova, Nadezhda; Sasorov, Pavel [Institute for Theoretical and Experimental Physics, B. Cheremushkinskaya str. 25, 117259 Moscow (Russian Federation); Kikuchi, Takashi; Sasaki, Toru [Department of Electrical Engineering, Nagaoka University of Technology, Kami-tomiokamachi 1603-1, Nagaoka, Niigata 940-2188 Japan (Japan); Higashiguchi, Takeshi; Yugami, Noboru [Department of Advanced Interdisciplinary Sciences, and Center for Optical Research and Education (CORE) Utsunomiya University, Yoto 7-1-2, Utsunomiya, Tochigi 321-8585 (Japan); Japan Science and Technology Agency, CREST, 4-1-8 Honcho, Kanagawa, Saitama 332-0012 (Japan); Kodama, Ryosuke [Japan Science and Technology Agency, CREST, 4-1-8 Honcho, Kanagawa, Saitama 332-0012 (Japan); Graduate School of Engineering, Osaka University, 2-6 Yamada-oka, Suita, Osaka 565-0871 (Japan)

    2011-03-01T23:59:59.000Z

    We observed the parameters of the discharge-produced plasma in cylindrical capillary. Plasma parameters of the waveguide were investigated by use of both a Normarski laser interferometer and a hydrogen plasma line spectrum. A space-averaged maximum temperature of 3.3 eV with electron densities of the order of 10{sup 17} cm{sup -3} was observed at a discharge time of 150 ns and a maximum discharge current of 200 A. One-dimensional dissipative magnetohydrodynamic (MHD) code was used to analyze the discharge dynamics in the gas-filled capillary discharge waveguide for high-intensity laser pulses. Simulations were performed for the conditions of the experiment. We compared the temporal behavior of the electron temperature and the radial electron density profiles, measured in the experiment with the results of the numerical simulations. They occurred to be in a good agreement. An ultrashort, intense laser pulse was guided by use of this plasma channel.

  11. Features of plasma glow in low pressure terahertz gas discharge

    SciTech Connect (OSTI)

    Bratman, V. L.; Golubev, S. V.; Izotov, I. V.; Kalynov, Yu. K.; Koldanov, V. A.; Razin, S. V. [Institute of Applied Physics, Russian Academy of Sciences, Nizhny Novgorod 603950 (Russian Federation)] [Institute of Applied Physics, Russian Academy of Sciences, Nizhny Novgorod 603950 (Russian Federation); Litvak, A. G.; Sidorov, A. V.; Skalyga, V. A.; Zorin, V. G. [Institute of Applied Physics, Russian Academy of Sciences, Nizhny Novgorod 603950 (Russian Federation) [Institute of Applied Physics, Russian Academy of Sciences, Nizhny Novgorod 603950 (Russian Federation); Lobachevsky State University of Nizhny Novgorod (UNN), 23 Gagarina st., 603950 Nizhny Novgorod (Russian Federation)

    2013-12-15T23:59:59.000Z

    Investigations of the low pressure (1–100 Torr) gas discharge in the powerful (1 kW) quasi-optical terahertz (0.55 THz) wave beams were made. An intense afterglow was observed after the end of gyrotron terahertz radiation pulse. Afterglow duration significantly exceeded radiation pulse length (8 ?s). This phenomenon could be explained by the strong dependence of the collisional-radiative recombination rate (that is supposed to be the most likely mechanism of electron losses from the low pressure terahertz gas discharge) on electron temperature.

  12. Differential pressure pin discharge apparatus

    DOE Patents [OSTI]

    Oakley, David J. (Richland, WA)

    1987-01-01T23:59:59.000Z

    Disclosed is a discharge assembly for allowing elongate pins to be discharged from an area of relatively low pressure to an area of relatively greater pressure. The discharge assembly includes a duck valve having a lip piece made of flexible material. The flexible lip piece responds to a fluctuating pressure created downstream by an aspirator. The aspirator reduces the downstream pressure sensed by the duck valve when the discharge assembly is in the open position. This allows elongate pins to be moved through the duck valve with no backflow because the aspirator pressure is less than the pressure in the low pressure area from which the pins originate. Closure of the assembly causes the aspirator static pressure to force the flexible duck valve lip piece into a tightly sealed position also preventing backflow. The discharge assembly can be easily controlled using a single control valve which blocks the flow of aspirator gas and closes the pin passageway extending through the assembly.

  13. Capillary discharge source

    DOE Patents [OSTI]

    Bender, III, Howard Albert

    2003-11-25T23:59:59.000Z

    Debris generation from an EUV electric discharge plasma source device can be significantly reduced or essentially eliminated by encasing the electrodes with dielectric or electrically insulating material so that the electrodes are shielded from the plasma, and additionally by providing a path for the radiation to exit wherein the electrodes are not exposed to the area where the radiation is collected. The device includes: (a) a body, which is made of an electrically insulating material, that defines a capillary bore that has a proximal end and a distal end and that defines at least one radiation exit; (b) a first electrode that defines a first channel that has a first inlet end that is connected to a source of gas and a first outlet end that is in communication with the capillary bore, wherein the first electrode is positioned at the distal end of the capillary bore; (c) a second electrode that defines a second channel that has a second inlet end that is in communication with the capillary bore and an outlet end, wherein the second electrode is positioned at the proximal end of the capillary bore; and (d) a source of electric potential that is connected across the first and second electrodes, wherein radiation generated within the capillary bore is emitted through the at least one radiation exit and wherein the first electrode and second electrode are shielded from the emitted radiation.

  14. Industrial Discharge Permits (District of Columbia)

    Broader source: Energy.gov [DOE]

    All businesses and government agencies discharging process wastewater to the public sewer system must report their activities to DC Water's Pretreatment Center. Wastewater discharge permits are...

  15. Groundwater Discharge Permit and Registration (New Hampshire)

    Broader source: Energy.gov [DOE]

    The Groundwater Discharge Permitting and Registration Program seeks to protect groundwater quality by establishing standards, criteria, and procedures for wastewater discharges. The program...

  16. Laser intensity effects in noncommutative QED

    E-Print Network [OSTI]

    Thomas Heinzl; Anton Ilderton; Mattias Marklund

    2010-02-17T23:59:59.000Z

    We discuss a two-fold extension of QED assuming the presence of strong external fields provided by an ultra-intense laser and noncommutativity of spacetime. While noncommutative effects leave the electron's intensity induced mass shift unchanged, the photons change significantly in character: they acquire a quasi-momentum that is no longer light-like. We study the consequences of this combined noncommutative strong-field effect for basic lepton-photon interactions.

  17. Discharge cell for ozone generator

    DOE Patents [OSTI]

    Nakatsuka, Suguru (Amagasaki, JP)

    2000-01-01T23:59:59.000Z

    A discharge cell for use in an ozone generator is provided which can suppress a time-related reduction in ozone concentration without adding a catalytic gas such as nitrogen gas to oxygen gas as a raw material gas. The discharge cell includes a pair of electrodes disposed in an opposed spaced relation with a discharge space therebetween, and a dielectric layer of a three-layer structure consisting of three ceramic dielectric layers successively stacked on at least one of the electrodes, wherein a first dielectric layer of the dielectric layer contacting the one electrode contains no titanium dioxide, wherein a second dielectric layer of the dielectric layer exposed to the discharge space contains titanium dioxide in a metal element ratio of not lower than 10 wt %.

  18. Journal of Engineering Mathematics Optimal discharging in a branched estuary Optimal discharging in a branched estuary

    E-Print Network [OSTI]

    that returns to the discharge site is less polluted than would 1 #12;Journal of Engineering Mathematics OptimalJournal of Engineering Mathematics Optimal discharging in a branched estuary Optimal discharging the proximity of the discharge site to the branching and upon how the rate of discharge is adjusted. Explicit

  19. Energy Intensity of Agriculture and Food Systems

    E-Print Network [OSTI]

    Wang, Changlu

    dependencies in the light of energy price volatility and concerns as to long-term fossil energy availabilities ENERGY USE. . . . . . . . . . 232 6. FOOD WASTE AND ENERGY USE. . . . . . . . . . . . . Energy Intensity of Agriculture and Food Systems Nathan Pelletier,1 Eric Audsley,2 Sonja Brodt,3

  20. Constricted glow discharge plasma source

    DOE Patents [OSTI]

    Anders, Andre (Albany, CA); Anders, Simone (Albany, CA); Dickinson, Michael (San Leandro, CA); Rubin, Michael (Berkeley, CA); Newman, Nathan (Winnetka, IL)

    2000-01-01T23:59:59.000Z

    A constricted glow discharge chamber and method are disclosed. The polarity and geometry of the constricted glow discharge plasma source is set so that the contamination and energy of the ions discharged from the source are minimized. The several sources can be mounted in parallel and in series to provide a sustained ultra low source of ions in a plasma with contamination below practical detection limits. The source is suitable for applying films of nitrides such as gallium nitride and oxides such as tungsten oxide and for enriching other substances in material surfaces such as oxygen and water vapor, which are difficult process as plasma in any known devices and methods. The source can also be used to assist the deposition of films such as metal films by providing low-energy ions such as argon ions.

  1. Microwave generated plasma light source apparatus

    SciTech Connect (OSTI)

    Yoshizawa, K.; Ito, H.; Kodama, H.; Komura, H.; Minowa, Y.

    1985-02-05T23:59:59.000Z

    A microwave generated plasma light source including a microwave generator, a microwave cavity having a light reflecting member forming at least a portion of the cavity, and a member transparent to light and opaque to microwaves disposed across an opening of the cavity opposite the feeding opening through which the microwave generator is coupled. An electrodeless discharge bulb is disposed at a position in the cavity such that the cavity operates as a resonant cavity at least when the bulb is emitting light. In the bulb is encapsulated at least one discharge light emissive substance. The bulb has a shape and is sufficiently small that the bulb acts substantially as a point light source.

  2. Compact monolithic capacitive discharge unit

    DOE Patents [OSTI]

    Roesler, Alexander W. (Tijeras, NM); Vernon, George E. (Rio Rancho, NM); Hoke, Darren A. (Albuquerque, NM); De Marquis, Virginia K. (Tijeras, NM); Harris, Steven M. (Albuquerque, NM)

    2007-06-26T23:59:59.000Z

    A compact monolithic capacitive discharge unit (CDU) is disclosed in which a thyristor switch and a flyback charging circuit are both sandwiched about a ceramic energy storage capacitor. The result is a compact rugged assembly which provides a low-inductance current discharge path. The flyback charging circuit preferably includes a low-temperature co-fired ceramic transformer. The CDU can further include one or more ceramic substrates for enclosing the thyristor switch and for holding various passive components used in the flyback charging circuit. A load such as a detonator can also be attached directly to the CDU.

  3. State Waste Discharge Permit application, 183-N Backwash Discharge Pond

    SciTech Connect (OSTI)

    Not Available

    1994-06-01T23:59:59.000Z

    As part of the Hanford Federal Facility Agreement and Consent Order negotiations (Ecology et al. 1994), the US Department of Energy, Richland Operations Office, the US Environmental Protection Agency, and the Washington State Department of Ecology agreed that liquid effluent discharges to the ground on the Hanford Site which affect groundwater or have the potential to affect groundwater would be subject to permitting under the structure of Chapter 173--216 (or 173--218 where applicable) of the Washington Administrative Code, the State Waste Discharge Permit Program. As a result of this decision, the Washington State Department of Ecology and the US Department of Energy, Richland Operations Office entered into Consent Order No. DE91NM-177, (Ecology and DOE-RL 1991). The Consent Order No. DE91NM-177 requires a series of permitting activities for liquid effluent discharges. Liquid effluents on the Hanford Site have been classified as Phase I, Phase II, and Miscellaneous Streams. The Consent Order No. DE91NM-177 establishes milestones for State Waste Discharge Permit application submittals for all Phase I and Phase II streams, as well as the following 11 Miscellaneous Streams as identified in Table 4 of the Consent Order No. DE91NM-177.

  4. Intensity Frontier Instrumentation

    E-Print Network [OSTI]

    S. H. Kettell; R. A. Rameika; R. S. Tschirhart

    2013-09-26T23:59:59.000Z

    This report summarizes findings of the 2013 Snowmass Community Summer Study Instrumentation Frontier's subgroup on the Intensity Frontier. This report is directed at identifying instrumentation R&D needed to support particle physics research over the coming decades at the Intensity Frontier.

  5. Commercial Lighting

    Broader source: Energy.gov [DOE]

    Commercial lighting accounts for more than 20 percent of total commercial building energy use. The Energy Department works to reduce lighting energy use through research and deployment.

  6. Growth of tungsten nanoparticles in direct-current argon glow discharges

    SciTech Connect (OSTI)

    Kishor Kumar, K.; Coueedel, L.; Arnas, C. [Laboratoire de Physique des Interactions Ioniques et Moleculaires, CNRS-Aix-Marseille Universite, 13397 Marseille (France)

    2013-04-15T23:59:59.000Z

    The growth of nanoparticles from the sputtering of a tungsten cathode in DC argon glow discharges is reported. The study was performed at fixed argon pressure and constant discharge current. The growth by successive agglomerations is evidenced. First, tungsten nanocrystallites agglomerate into primary particles, the most probable size of which being {approx}30 nm. Primary particles of this size are observed for all plasma durations and always remain the most numerous in the discharge. Primary particles quickly agglomerate to form particles with size up to {approx}150 nm. For short plasma duration, log-normal functions describe accurately the dust particle size distributions. On the contrary, for long discharge durations, a second hump appears in the distributions toward large particle sizes. In the meantime, the discharge voltage, electron density, and emission line intensities strongly evolve. Their evolutions can be divided in four separate phases and exhibit unusual distinctive features compared to earlier observations in discharges in which particles were growing. The evolution of the different parameters is explained by a competition between the surface state of the tungsten cathode and the influence of the growing nanoparticles. The differences with sputtering glow discharges and chemically active plasmas suggest that the nanoparticle growth and its influence on discharge parameters is system and material dependent.

  7. Experimental Diagnostics and Modeling of Microplasma Discharges

    E-Print Network [OSTI]

    Economou, Demetre J.

    ;Challenge · Difficult to perform conventional diagnostics in micro-plasma discharges because of their small size. Optical diagnostics are most convenient. #12;Plasma Processing Laboratory Experimental SetupExperimental Diagnostics and Modeling of Microplasma Discharges Department of Chemical

  8. Oklahoma Pollutant Discharge Elimination System Act (Oklahoma)

    Broader source: Energy.gov [DOE]

    The Department of Environmental Quality regulates facilities that discharge any pollutant into waters of the state. Permits must be acquired before the discharge of any pollutants into state waters...

  9. State Surface Water Discharge Permits (New Hampshire)

    Broader source: Energy.gov [DOE]

    Rules apply to the discharge of all pollutants from a point source to surface waters of the state. The rule does not apply to facilities that require both a state discharge permit and a federal...

  10. Focused shock spark discharge drill using multiple electrodes

    DOE Patents [OSTI]

    Moeny, William M. (Albuquerque, NM); Small, James G. (Albuquerque, NM)

    1988-01-01T23:59:59.000Z

    A spark discharge focused drill provided with one pulse forming line or a number of pulse forming lines. The pulse forming line is connected to an array of electrodes which would form a spark array. One of the electrodes of each of the array is connected to the high voltage side of the pulse forming line and the other electrodes are at ground potential. When discharged in a liquid, these electrodes produce intense focused shock waves that can pulverize or fracture rock. By delaying the firing of each group of electrodes, the drill can be steered within the earth. Power can be fed to the pulse forming line either downhole or from the surface area. A high voltage source, such as a Marx generator, is suitable for pulse charging the lines.

  11. The Intense Radiation Gas

    E-Print Network [OSTI]

    M. Marklund; P. K. Shukla; B. Eliasson

    2005-03-08T23:59:59.000Z

    We present a new dispersion relation for photons that are nonlinearly interacting with a radiation gas of arbitrary intensity due to photon-photon scattering. It is found that the photon phase velocity decreases with increasing radiation intensity, it and attains a minimum value in the limit of super-intense fields. By using Hamilton's ray equations, a self-consistent kinetic theory for interacting photons is formulated. The interaction between an electromagnetic pulse and the radiation gas is shown to produce pulse self-compression and nonlinear saturation. Implications of our new results are discussed.

  12. 2, 22872325, 2005 discharge+sediment

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    HESSD 2, 2287­2325, 2005 Water discharge+sediment flux changes in Lower Mekon River X. X. Lu and R Sciences Water discharge and sediment flux changes in the Lower Mekong River X. X. Lu and R. Y. Siew­2325, 2005 Water discharge+sediment flux changes in Lower Mekon River X. X. Lu and R. Y. Siew Title Page

  13. Solar radiation intensity calculations

    E-Print Network [OSTI]

    Levine, Randolph Steven

    1978-01-01T23:59:59.000Z

    SOLAR RADIATION INTENSITY CALCULATIONS A Thesis by RANDOLPH STEVEN LEVINE Submitted to the Graduate College of Texas A&M University in partia'l fulfillment of the requirement for the degree of MASTER OF SCIENCE December 1978 Major Subject...: Physics SOLAR RADIATION INTENSITY CALCULATIONS A Thesis by RANDOLPH STEVEN LEVINE Approved as to style and content by: (Chairman of Committee) (Member) (Member) ( member) (Head of Department) December 1978 f219 037 ABSTRACT Solar Radiation...

  14. State waste discharge permit application for cooling water and condensate discharges

    SciTech Connect (OSTI)

    Haggard, R.D.

    1996-08-12T23:59:59.000Z

    The following presents the Categorical State Waste Discharge Permit (SWDP) Application for the Cooling Water and Condensate Discharges on the Hanford Site. This application is intended to cover existing cooling water and condensate discharges as well as similar future discharges meeting the criteria set forth in this document.

  15. Spent nuclear fuel discharges from US reactors 1993

    SciTech Connect (OSTI)

    Not Available

    1995-02-01T23:59:59.000Z

    The Energy Information Administration (EIA) of the U.S. Department of Energy (DOE) administers the Nuclear Fuel Data Survey, Form RW-859. This form is used to collect data on fuel assemblies irradiated at commercial nuclear reactors operating in the United States, and the current inventories and storage capacities of those reactors. These data are important to the design and operation of the equipment and facilities that DOE will use for the future acceptance, transportation, and disposal of spent fuels. The data collected and presented identifies trends in burnup, enrichment, and spent nuclear fuel discharged form commercial light-water reactor as of December 31, 1993. The document covers not only spent nuclear fuel discharges; but also site capacities and inventories; canisters and nonfuel components; and assembly type characteristics.

  16. Environmental and health aspects of lighting: Mercury

    SciTech Connect (OSTI)

    Clear, R.; Berman, S.

    1993-07-01T23:59:59.000Z

    Most discharge lamps, including fluorescent lamps, metal halide lamps, and high pressure sodium lamps, contain Mercury, a toxic chemical. Lighting professionals need to be able to respond to questions about the direct hazards of Mercury from accidentally breaking lamps, and the potential environmental hazards of lamp operation and disposal. We calculated the exposures that could occur from an accidental breakage of lamps. Acute poisoning appears almost impossible. Under some circumstances a sealed environment, such as a space station, could be contaminated enough to make it unhealthy for long-term occupation. Mercury becomes a potential environmental hazard after it becomes methylated. Mercury is methylated in aquatic environments, where it may accumulate in fish, eventually rendering them toxic to people and other animals. Lighting causes Mercury to enter the environment directly from lamp disposal, and indirectly from power plant emissions. The environmental tradeoffs between incandescent and discharge lamps depend upon the amounts released by these two sources, their local concentrations, and their probabilities of being methylated. Indirect environmental effects of lighting also include the release of other heavy metals (Cadmium, Lead and Arsenic), and other air pollutants and carbon dioxide that are emitted by fossil fuel power plants. For a given light output, the level of power plant emissions depends upon the efficacy of the light source, and is thus much larger for incandescent lamps than for fluorescent or discharge lamps. As disposal and control technologies change the relative direct and indirect emissions from discharge and incandescent lamps will change.

  17. General Electric Lighting The last couple months at General Electric Lighting have been very exciting. In addition to the

    E-Print Network [OSTI]

    Rollins, Andrew M.

    a high voltage is applied to them, a plasma arc is formed, and the intense heat causes the electrons. I am still currently in the High Intensity Discharge (HID) division, working on a new outdoor lamp amounts of these elements are used to carefully control the color balance of the lamp. For example, sodium

  18. Narrow gap electronegative capacitive discharges

    SciTech Connect (OSTI)

    Kawamura, E.; Lieberman, M. A.; Lichtenberg, A. J. [Department of Electrical Engineering and Computer Sciences, University of California, Berkeley, California 94720 (United States)] [Department of Electrical Engineering and Computer Sciences, University of California, Berkeley, California 94720 (United States)

    2013-10-15T23:59:59.000Z

    Narrow gap electronegative (EN) capacitive discharges are widely used in industry and have unique features not found in conventional discharges. In this paper, plasma parameters are determined over a range of decreasing gap length L from values for which an electropositive (EP) edge exists (2-region case) to smaller L-values for which the EN region connects directly to the sheath (1-region case). Parametric studies are performed at applied voltage V{sub rf}=500 V for pressures of 10, 25, 50, and 100 mTorr, and additionally at 50 mTorr for 1000 and 2000 V. Numerical results are given for a parallel plate oxygen discharge using a planar 1D3v (1 spatial dimension, 3 velocity components) particle-in-cell (PIC) code. New interesting phenomena are found for the case in which an EP edge does not exist. This 1-region case has not previously been investigated in detail, either numerically or analytically. In particular, attachment in the sheaths is important, and the central electron density n{sub e0} is depressed below the density n{sub esh} at the sheath edge. The sheath oscillations also extend into the EN core, creating an edge region lying within the sheath and not characterized by the standard diffusion in an EN plasma. An analytical model is developed using minimal inputs from the PIC results, and compared to the PIC results for a base case at V{sub rf}=500 V and 50 mTorr, showing good agreement. Selected comparisons are made at the other voltages and pressures. A self-consistent model is also developed and compared to the PIC results, giving reasonable agreement.

  19. Non-storm water discharges technical report

    SciTech Connect (OSTI)

    Mathews, S.

    1994-07-01T23:59:59.000Z

    Lawrence Livermore National Laboratory (LLNL) submitted a Notice of Intent to the California State Water Resources Control Board (hereafter State Board) to discharge storm water associated with industrial activities under the California General Industrial Activity Storm Water National Pollutant Elimination System Discharge Permit (hereafter General Permit). As required by the General Permit, LLNL provided initial notification of non-storm water discharges to the Central Valley Regional Water Quality Control Board (hereafter Regional Board) on October 2, 1992. Additional findings and progress towards corrective actions were reported in subsequent annual monitoring reports. LLNL was granted until March 27, 1995, three years from the Notice of Intent submission date, to eliminate or permit the non-storm water discharges. On May 20, 1994, the Regional Board issued Waste Discharge Requirements (WDR Board Order No. 94-131, NPDES No. CA0081396) to LLNL for discharges of non-contact cooling tower wastewater and storm water related to industrial activities. As a result of the issuance of WDR 94-131, LLNL rescinded its coverage under the General Permit. WDR 94-131 allowed continued non-storm water discharges and requested a technical report describing the discharges LLNL seeks to permit. For the described discharges, LLNL anticipates the Regional Board will either waive Waste Discharge Requirements as allowed for in The Water Quality Control Plan for the California Regional Water Quality Control Board, Central Valley Region (hereafter Basin Plan) or amend Board Order 94-131 as appropriate.

  20. Determination of electron temperature from spectral line intensity decay for radiation dominated plasmas

    SciTech Connect (OSTI)

    Michael, C.A.; Howard, J. [PRL, RSPhysSE, Australian National University, Canberra A.C.T. 0200 (Australia)

    2004-10-01T23:59:59.000Z

    We describe a technique to absolutely estimate the electron temperature in radiation dominated plasmas from the temporal decay during the plasma afterglow of the intensity of a single spectral line. The model and underlying assumptions are described. We apply the model to data in both rf heated argon discharges and electron cyclotron heated He/H discharges in the H-1 heliac. The results agree well with probe measurements.

  1. Dusty Plasma in He-Ar Glow Discharge

    SciTech Connect (OSTI)

    Maiorov, S. A. [A. M. Prokhorov Institute for General Physics under Russian Academy of Sciences, Moscow (Russian Federation); Ramazanov, T. S.; Dzhumagulova, K. N.; Dosbolayev, M. K.; Jumabekov, A. N. [IETP, al-Farabi Kazakh National University, 96a, Tole bi St., Almaty, 050012 (Kazakhstan)

    2008-09-07T23:59:59.000Z

    The paper reports on the first experiments with plasma-dust formations in dc gas discharge plasma for He-Ar mixture. It is shown that under the conventional conditions of the experiments with dusty structures in plasma, the choice of light and heavy gases for the mixture suppresses electron heating in electric field and results in a supersonic jet with high Mach numbers. Distribution functions for drifting ions in the gas mixture are calculated for various mixture concentrations, electric field strengths and gas pressures.

  2. Energy Intensity Strategy

    E-Print Network [OSTI]

    Rappolee, D.; Shaw, J.

    2008-01-01T23:59:59.000Z

    Our presentation will cover how we began the journey of conserving energy at our facility. We’ll discuss a basic layout of our energy intensity plan and the impact our team has had on the process, what tools we’re using, what goals have been...

  3. Smart Lighting Controller!! Smart lighting!

    E-Print Network [OSTI]

    Anderson, Betty Lise

    1! Smart Lighting Controller!! #12;2! Smart lighting! No need to spend energy lighting the room if://blogs.stthomas.edu/realestate/2011/01/24/residential-real-estate-professionals-how-do-you- develop feedback! There is a connection between the output and the input! Therefore forces inputs to same voltage

  4. Generation of high-current electron beam in a wide-aperture open discharge

    SciTech Connect (OSTI)

    Bokhan, P. A.; Zakrevsky, Dm. E.; Gugin, P. P. [A. V. Rzhanov Institute of Semiconductor Physics, Siberian Branch of the Russian Academy of Sciences, prospekt Lavrent'eva 13, Novosibirsk 630090 (Russian Federation)

    2011-10-15T23:59:59.000Z

    In the present study, it was examined generation of nanosecond-duration electron-beam (EB) pulses by a wide-aperture open discharge burning in helium or in a mixture of helium with nitrogen and water vapor. In the experiments, a discharge cell with coaxial electrode geometry, permitting radial injection of the electron beam into operating lasing medium, was used, with the cathode having radius 2.5 cm and length 12 cm. It was shown possible to achieve an efficient generation of a high-intensity electron beam (EB pulse power {approx}250 MW and EB pulse energy up to 4 J) in the kiloampere range of discharge currents (up to 26 kA at {approx}12 kV discharge voltage). The current-voltage characteristics of the discharge proved to be independent of the working-gas pressure. The existence of an unstable dynamic state of EB, conditioned by the presence of an uncompensated space charge accumulated in the discharge cell due to the exponential growth of the current in time during discharge initiation and the hyperbolic growth of current density in the direction towards the tube axis, was revealed. The obtained pulsed electron beam was used to excite the self-terminated laser on He 2{sup 1}P{sub 1}{sup 0}-2{sup 1}S{sub 0} transition. The oscillations developing in the discharge cell at high discharge currents put limit to the pumping energy and emissive power of the laser excited with the radially converging electron beam.

  5. Site Discharge Pollution Prevention Plan (SDPPP)

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    SDPPP Individual Permit: Site Discharge Pollution Prevention Plan (SDPPP) The 2012 SDPPP update fully incorporates all changes made during the year and reflects changes projected...

  6. EPA - National Pollutant Discharge Elimination System General...

    Open Energy Info (EERE)

    General Permit for Discharges from Construction Activities Jump to: navigation, search OpenEI Reference LibraryAdd to library PermittingRegulatory Guidance - GuideHandbook: EPA -...

  7. Device for generation of pulsed corona discharge

    DOE Patents [OSTI]

    Gutsol, Alexander F. (San Ramon, CA); Fridman, Alexander (Marlton, NJ); Blank, Kenneth (Philadelphia, PA); Korobtsev, Sergey (Moscow, RU); Shiryaevsky, Valery (Moscow, RU); Medvedev, Dmitry (Moscow, RU)

    2012-05-08T23:59:59.000Z

    The invention is a method and system for the generation of high voltage, pulsed, periodic corona discharges capable of being used in the presence of conductive liquid droplets. The method and system can be used, for example, in different devices for cleaning of gaseous or liquid media using pulsed corona discharge. Specially designed electrodes and an inductor increase the efficiency of the system, permit the plasma chemical oxidation of detrimental impurities, and increase the range of stable discharge operations in the presence of droplets of water or other conductive liquids in the discharge chamber.

  8. Oil and Hazardous Substance Discharge Preparedness (Minnesota)

    Broader source: Energy.gov [DOE]

    Anyone who owns or operates a vessel or facility that transports, stores, or otherwise handles hazardous wastes must take reasonable steps to prevent the discharge of those materials.

  9. Commercial Lighting and LED Lighting Incentives

    Broader source: Energy.gov [DOE]

    Incentives for energy efficient commercial lighting equipment as well as commercial LED lighting equipment are available to businesses under the Efficiency Vermont Lighting and LED Lighting...

  10. Vacuum ultra-violet emission of plasma discharges with high Xe partial pressure using a cathode protective layer with high secondary electron emission

    SciTech Connect (OSTI)

    Zhu, Di [School of Electronics and Information Engineering, Tianjin Polytechnic University, Tianjin (China); Song, Le, E-mail: songle@tju.edu.cn [State Key Laboratory of Precision Measuring Technology and Instruments, Tianjin University, Tianjin (China); Zhang, Xiong [School of Electronic Science and Engineering, Southeast University, Nanjing (China); Kajiyama, Hiroshi [Graduate School of Advanced Science of Matter, Hiroshima University, Higashi-hiroshima, Hiroshima (Japan)

    2014-02-14T23:59:59.000Z

    In this work, the mechanism of the vacuum ultra-violet (VUV) emission of plasma discharges, with high Xe partial pressure and high ion-induced secondary electrons emission protective layer, is studied by measuring the VUV light emission directly and comparing it with two-dimensional simulations. From the panel measurement, we find that the high intensity of excimer VUV mainly contributes to the high luminous efficacy of SrCaO-plasma display panels (PDP) at a low sustain voltage. The unchanged Xe excitation efficiency indicates that the electron temperature is not decreased by the high secondary electrons emission protective layer, even though the sustain voltage is much lower. From the two-dimensional simulations, we can find that the ratio of excimer VUV to resonant VUV, which is determined by the collision rate in the discharge, is only significantly affected by the Xe partial pressure, while it is independent of the sustain voltage and the secondary-electrons-emission capability of protective layer. The unchanged average electron energy at the moment when the electric field becomes maximum confirms that the improvement of the VUV production efficiency mainly is attributed to the increase in electron heating efficiency of a PDP with high ion-induced secondary electrons emission protective layer. Combining the experimental and the simulation results, we conclude about the mechanism by which the VUV production is improved for the plasma display panel with a high Xe partial pressure and a cold cathode with high ion-induced secondary electrons emission.

  11. Intense pulsed light sintering of copper nanoink for printed electronics

    E-Print Network [OSTI]

    Kim, Hak-Sung; Dhage, Sanjay R.; Shim, Dong-Eun; Hahn, H. Thomas

    2009-01-01T23:59:59.000Z

    During the arc plasma generation, the ?ash lamp emits anusing an arc plasma phenomenon in the xenon ?ash lamp [7].

  12. Lighting Renovations

    Broader source: Energy.gov [DOE]

    When undertaking a lighting renovation in a Federal building, daylighting is the primary renewable energy opportunity. Photovoltaics (PV) also present an excellent opportunity. While this guide...

  13. Cerenkov Light

    ScienceCinema (OSTI)

    Slifer, Karl

    2014-05-22T23:59:59.000Z

    The bright blue glow from nuclear reactors is Cerenkov light. Karl Slifer describes how nuclear physicists can use this phenomenon to study the nucleus of the atom.

  14. Cerenkov Light

    SciTech Connect (OSTI)

    Slifer, Karl

    2013-06-13T23:59:59.000Z

    The bright blue glow from nuclear reactors is Cerenkov light. Karl Slifer describes how nuclear physicists can use this phenomenon to study the nucleus of the atom.

  15. ElectricOIL discharge and post-discharge kinetics experiments and modeling

    E-Print Network [OSTI]

    Carroll, David L.

    oxygen, ozone, and other excited species adds levels of complexity to the singlet oxygen generator (SOG has been obtained by a near resonant energy transfer from O2(a1 ) produced using a low­pressure oxygen/helium/nitric-oxide discharge. In the electric discharge oxygen-iodine laser (ElectricOIL) the discharge production of atomic

  16. Initiation of long, free-standing Z-discharges by CO2 laser gas heating

    SciTech Connect (OSTI)

    Nieman, C.; Tauschwitz, A.; Penache, D.; Neff, S.; Knobloch, R.; Birkner, R.; Presura, R.; Hoffmann, D.H.H.; Yu, S.S.; Sharp, W.M.

    2004-04-19T23:59:59.000Z

    High current discharge channels can neutralize both current and space charge of very intense ion beams. Therefore they are considered as an interesting alternative for the final focus and beam transport in a heavy ion beam fusion reactor. At the GSI accelerator facility, 50 cm long, stable, free-standing discharge channels with currents in excess of 40 kA in 2 to 25 mbar ammonia (NH{sub 3}) gas are investigated for heavy ion beam transport studies. The discharges are initiated by a CO{sub 2} laser pulse along the channel axis before the discharge is triggered. Resonant absorption of the laser, tuned to the {nu}{sub 2} vibration of the ammonia molecule, causes strong gas heating. Subsequent expansion and rarefaction of the gas prepare the conditions for a stable discharge to fulfill the requirements for ion beam transport. This paper describes the laser-gas interaction and the discharge initiation mechanism. We report on the channel stability and evolution, measured by fast shutter and streak imaging techniques. The rarefaction of the laser heated gas is studied by means of a hydrocode simulation.

  17. Effect of pulse intensity distributions on fragment internal energy in the infrared multiphoton dissociation of vinyl

    E-Print Network [OSTI]

    Zare, Richard N.

    Effect of pulse intensity distributions on fragment internal energy in the infrared multiphoton of laser intensity on the production of fragment energy distribu- tions. Laser induced fluorescence (LIF pumping is pro- portional to the light intensity, the final energy of the parent molecule

  18. Plasma discharge self-cleaning filtration system

    DOE Patents [OSTI]

    Cho, Young I.; Fridman, Alexander; Gutsol, Alexander F.; Yang, Yong

    2014-07-22T23:59:59.000Z

    The present invention is directed to a novel method for cleaning a filter surface using a plasma discharge self-cleaning filtration system. The method involves utilizing plasma discharges to induce short electric pulses of nanoseconds duration at high voltages. These electrical pulses generate strong Shockwaves that disintegrate and dislodge particulate matter located on the surface of the filter.

  19. Kinetic Effects In Hall Thruster Discharge

    E-Print Network [OSTI]

    Kaganovich, Igor

    of a capacitive discharge. 4 capacitive discharge. For more info: V. Godyak, IEEE TPS 34, 755 (2006). #12 th twall interactions in Hall thrusters Large electron temperature andE JH~1cm secondary electron emission result in large particle and wall losses to the wall E , Jz z Br H~1cm 120 eV High SEE BN channel

  20. Atmospheric sampling glow discharge ionization source

    DOE Patents [OSTI]

    McLuckey, S.A.; Glish, G.L.

    1989-07-18T23:59:59.000Z

    An atmospheric sampling glow discharge ionization source that can be used in combination with an analytical instrument which operates at high vacuum, such as a mass spectrometer. The atmospheric sampling glow discharge ionization source comprises a chamber with at least one pair of electrodes disposed therein, an inlet for a gaseous sample to be analyzed and an outlet communicating with an analyzer which operates at subatmospheric pressure. The ionization chamber is maintained at a pressure below atmospheric pressure, and a voltage difference is applied across the electrodes to induce a glow discharge between the electrodes, so that molecules passing through the inlet are ionized by the glow discharge and directed into the analyzer. The ionization source accepts the sample under atmospheric pressure conditions and processes it directly into the high vacuum instrument, bridging the pressure gap and drawing off unwanted atmospheric gases. The invention also includes a method for analyzing a gaseous sample using the glow discharge ionization source described above. 3 figs.

  1. Oxygen Discharge and Post-Discharge Kinetics Experiments and Modeling for the Electric Oxygen-Iodine Laser System

    E-Print Network [OSTI]

    Carroll, David L.

    Oxygen Discharge and Post-Discharge Kinetics Experiments and Modeling for the Electric Oxygen a low-pressure oxygen/helium/nitric oxide discharge. In the electric discharge oxygen-iodine laser (ElectricOIL) the discharge production of atomic oxygen, ozone, and other excited species adds levels

  2. Evaluation of expanded uncertainties in luminous intensity and illuminance calibrations

    SciTech Connect (OSTI)

    Sametoglu, Ferhat

    2008-11-01T23:59:59.000Z

    Detector-based calibrating methods and expressions for calculation of photometric uncertainties related to uncertainties in the calibrations of luminous intensity of a light source, illuminance responsivity of a photometer head, and calibration factors of an illuminance meter are discussed. These methods permit luminous intensity calibrations of incandescent light sources, luminous responsivity calibrations of photometer heads, and calibration factors of illuminance meters to be carried out with relative expanded uncertainties (with a level of confidence of 95.45%) of 0.4%, 0.4%, and 0.6%, respectively.

  3. Fluid jet electric discharge source

    DOE Patents [OSTI]

    Bender, Howard A. (Ripon, CA)

    2006-04-25T23:59:59.000Z

    A fluid jet or filament source and a pair of coaxial high voltage electrodes, in combination, comprise an electrical discharge system to produce radiation and, in particular, EUV radiation. The fluid jet source is composed of at least two serially connected reservoirs, a first reservoir into which a fluid, that can be either a liquid or a gas, can be fed at some pressure higher than atmospheric and a second reservoir maintained at a lower pressure than the first. The fluid is allowed to expand through an aperture into a high vacuum region between a pair of coaxial electrodes. This second expansion produces a narrow well-directed fluid jet whose size is dependent on the size and configuration of the apertures and the pressure used in the reservoir. At some time during the flow of the fluid filament, a high voltage pulse is applied to the electrodes to excite the fluid to form a plasma which provides the desired radiation; the wavelength of the radiation being determined by the composition of the fluid.

  4. Transverse-type laser assembly using induced electrical discharge excitation and method

    DOE Patents [OSTI]

    Ault, E.R.

    1994-04-19T23:59:59.000Z

    A transverse-type laser assembly is disclosed herein. This assembly defines a laser cavity containing a vapor or gaseous substance which lases when subjected to specific electrical discharge excitation between a pair of spaced-apart electrodes located within the cavity in order to produce a source of light. An arrangement located entirely outside the laser cavity is provided for inducing a voltage across the electrodes within the cavity sufficient to provide the necessary electrical discharge excitation to cause a vapor substance between the electrodes to lase. 3 figures.

  5. Dynamics of multiple double layers in high pressure glow discharge in a simple torus

    SciTech Connect (OSTI)

    Kumar Paul, Manash, E-mail: manashkr@gmail.com [Department of Physics, National Institute of Technology Agartala, Tripura–799 046 (India); Sharma, P. K.; Thakur, A.; Kulkarni, S. V.; Bora, D. [Institute for Plasma Research, Bhat, Gandhinagar, Gujarat–382 428 (India)

    2014-06-15T23:59:59.000Z

    Parametric characterization of multiple double layers is done during high pressure glow discharge in a toroidal vessel of small aspect ratio. Although glow discharge (without magnetic field) is known to be independent of device geometry, but the toroidal boundary conditions are conducive to plasma growth and eventually the plasma occupy the toroidal volume partially. At higher anode potential, the visibly glowing spots on the body of spatially extended anode transform into multiple intensely luminous spherical plasma blob structures attached to the tip of the positive electrode. Dynamics of multiple double layers are observed in argon glow discharge plasma in presence of toroidal magnetic field. The radial profiles of plasma parameters measured at various toroidal locations show signatures of double layer formation in our system. Parametric dependence of double layer dynamics in presence of toroidal magnetic field is presented here.

  6. Intensity Frontier Instrumentation

    SciTech Connect (OSTI)

    Kettell S.; Rameika, R.; Tshirhart, B.

    2013-09-24T23:59:59.000Z

    The fundamental origin of flavor in the Standard Model (SM) remains a mystery. Despite the roughly eighty years since Rabi asked “Who ordered that?” upon learning of the discovery of the muon, we have not understood the reason that there are three generations or, more recently, why the quark and neutrino mixing matrices and masses are so different. The solution to the flavor problem would give profound insights into physics beyond the Standard Model (BSM) and tell us about the couplings and the mass scale at which the next level of insight can be found. The SM fails to explain all observed phenomena: new interactions and yet unseen particles must exist. They may manifest themselves by causing SM reactions to differ from often very precise predictions. The Intensity Frontier (1) explores these fundamental questions by searching for new physics in extremely rare processes or those forbidden in the SM. This often requires massive and/or extremely finely tuned detectors.

  7. HIGH INTENSITY DISCHARGE (HID) SOLID STATE BALLAST PROGRAM PHASE I FINAL REPORT

    E-Print Network [OSTI]

    Ailing, W.R.

    2013-01-01T23:59:59.000Z

    change in the output power for the solid state ballast asof the solid state ballast's constant output power withswitching power supplies such as the solid state ballast.

  8. HIGH INTENSITY DISCHARGE (HID) SOLID STATE BALLAST PROGRAM PHASE I FINAL REPORT

    E-Print Network [OSTI]

    Ailing, W.R.

    2013-01-01T23:59:59.000Z

    A trapazoid for each type and lamp wattage is published bylamp wattage for the core-coil ballast was measured with a dynamometer type

  9. 2014-05-05 Issuance: Test Procedures for High-Intensity Discharge Lamps;

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustionImprovement3 Beryllium-Associated Worker2014 HouseCovered ConsumerProcedures for

  10. Apparatus and process for active pulse intensity control of laser beam

    DOE Patents [OSTI]

    Wilcox, Russell B. (Oakland, CA)

    1992-01-01T23:59:59.000Z

    An optically controlled laser pulse energy control apparatus and process is disclosed wherein variations in the energy of a portion of the laser beam are used to vary the resistance of a photodetector such as a photoresistor through which a control voltage is fed to a light intensity controlling device through which a second portion of the laser beam passes. Light attenuation means are provided to vary the intensity of the laser light used to control the resistance of the photodetector. An optical delay path is provided through which the second portion of the beam travels before reaching the light intensity controlling device. The control voltage is supplied by a variable power supply. The apparatus may be tuned to properly attenuate the laser beam passing through the intensity controlling device by adjusting the power supply, the optical delay path, or the light attenuating means.

  11. Radioluminescent (RL) airfield lighting system program

    SciTech Connect (OSTI)

    Tompkins, J.A. (Westinghouse Electric Corp., Las Vegas, NV (USA)); Haff, K.W.; Schultz, F.J. (Oak Ridge National Lab., TN (USA))

    1990-09-01T23:59:59.000Z

    In 1980, the US Air Force Engineering and Services Center (AFESC) at Tyndall Air Force Base, Florida, requested that the Radioisotope Technology Group of Oak Ridge National Laboratory (ORNL) develop large-scale, tritium-powered, radioluminescent (RL) airfield lighting systems. The RL lighting systems possess the advantages of being portable, requiring no electrical power source, having a long shelf life, and being unaffected by environmental extremes. These characteristics make the RL system well-suited for harsh environments where the cost of electrical power production is high and traditional incandescent airfield lighting systems are difficult to maintain. RL lighting is typically a large-surface-area, low-intensity light source that operates 100% of the time. The RL light sources gradually decrease in brightness over time, so periodic replacement (every 6 to 8 years) is necessary. RL lighting functions best in low ambient light, which provides the high contrast ratios necessary for successful use of these devices. 12 figs., 8 tabs.

  12. Portable lamp with dynamically controlled lighting distribution

    DOE Patents [OSTI]

    Siminovitch, Michael J. (Pinole, CA); Page, Erik R. (Berkeley, CA)

    2001-01-01T23:59:59.000Z

    A double lamp table or floor lamp lighting system has a pair of compact fluorescent lamps (CFLs) arranged vertically with a reflective septum in between. By selectively turning on one or both of the CFLs, down lighting, up lighting, or both up and down lighting is produced. The control system can also vary the light intensity from each CFL. The reflective septum insures that almost all the light produced by each lamp will be directed into the desired light distribution pattern which is selected and easily changed by the user. Planar compact fluorescent lamps, e.g. circular CFLs, particularly oriented horizontally, are preferable. CFLs provide energy efficiency. The lighting system may be designed for the home, hospitality, office or other environments.

  13. Glow discharge plasma deposition of thin films

    DOE Patents [OSTI]

    Weakliem, Herbert A. (Pennington, NJ); Vossen, Jr., John L. (Bridgewater, NJ)

    1984-05-29T23:59:59.000Z

    A glow discharge plasma reactor for deposition of thin films from a reactive RF glow discharge is provided with a screen positioned between the walls of the chamber and the cathode to confine the glow discharge region to within the region defined by the screen and the cathode. A substrate for receiving deposition material from a reactive gas is positioned outside the screened region. The screen is electrically connected to the system ground to thereby serve as the anode of the system. The energy of the reactive gas species is reduced as they diffuse through the screen to the substrate. Reactive gas is conducted directly into the glow discharge region through a centrally positioned distribution head to reduce contamination effects otherwise caused by secondary reaction products and impurities deposited on the reactor walls.

  14. Life cycle assessment of buildings technologies: High-efficiency commercial lighting and residential water heaters

    SciTech Connect (OSTI)

    Freeman, S.L.

    1997-01-01T23:59:59.000Z

    In this study the life cycle emissions and energy use are estimated for two types of energy technologies. The first technology evaluated is the sulfur lamp, a high-efficiency lighting system under development by the US Department of Energy (DOE) and Fusion Lighting, the inventor of the technology. The sulfur lamp is compared with conventional metal halide high-intensity discharge lighting systems. The second technology comparison is between standard-efficiency and high-efficiency gas and electric water heaters. In both cases the life cycle energy use and emissions are presented for the production of an equivalent level of service by each of the technologies. For both analyses, the energy use and emissions from the operation of the equipment are found to dominate the life cycle profile. The life cycle emissions for the water heating systems are much more complicated. The four systems compared include standard- and high-efficiency gas water heaters, standard electric resistance water heaters, and heat pump water heaters.

  15. Discharge dynamics of pin-to-plate dielectric barrier discharge at atmospheric pressure

    SciTech Connect (OSTI)

    Sun Liqun [College of Science, Donghua University, Shanghai 201620 (China); Huang, Xiaojiang [College of Science, Donghua University, Shanghai 201620 (China); Member of Magnetic Confinement Fusion Research Center, Ministry of Education of the People's Republic of China, Shanghai 201620 (China); Zhang Jie [College of Science, Donghua University, Shanghai 201620 (China); State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, College of Material Science and Engineering, Donghua University, Shanghai 201620 (China); Zhang Jing; Shi, J. J. [College of Science, Donghua University, Shanghai 201620 (China); State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, College of Material Science and Engineering, Donghua University, Shanghai 201620 (China); Member of Magnetic Confinement Fusion Research Center, Ministry of Education of the People's Republic of China, Shanghai 201620 (China)

    2010-11-15T23:59:59.000Z

    The discharge dynamics of pin-to-plate dielectric barrier discharge was studied in atmospheric helium at 20 kHz. The discharge was predominately ignited in positive half cycle of applied voltage with sinusoidal waveform. The temporal evolution of the discharge was investigated vertically along the discharge gap and radically on the dielectric surface by time resolved imaging. It is found that a discharge column with a diameter of 2 mm was ignited above the pin electrode and expanded toward a plate electrode. On the dielectric surface with space charge accumulation, plasma disk in terms of plasma ring was formed with radius up to 25 mm. The expansion velocity of plasma ring can reach a hypersonic speed of 3.0 km/s. The ionization wave due to electron diffusion is considered to be the mechanism for plasma ring formation and dynamics.

  16. Impedance response to induced epileptiform discharges

    E-Print Network [OSTI]

    Gerber, Terry Lynn

    2012-06-07T23:59:59.000Z

    Subject: Bioengineering IMPEDANCE RESPONSE TO INDUCED EPILEPTIFORM DISCHARGES A Thesis by TERRY LYNN GERBER Approved as to style and content by erald E. Miller ( irman of Committee) William A. H an (Member) / , I / vW C' (gp frt 't- Thomas... W. Adair (Member) Newton C. Ellis (Head of Department) May 1984 ABSTRACT Impedance Response to Induced Epileptiform Discharges. (May 1984) Terry Lynn Gerber, B. S. , Texas A&M University Chairman of Advisory Committee: Dr. Gerald E. Miller...

  17. Magnetic dipole discharges. II. Cathode and anode spot discharges and probe diagnostics

    SciTech Connect (OSTI)

    Stenzel, R. L.; Urrutia, J. M. [Department of Physics and Astronomy, University of California, Los Angeles, California 90095-1547 (United States)] [Department of Physics and Astronomy, University of California, Los Angeles, California 90095-1547 (United States); Ionita, C.; Schrittwieser, R. [Institute for Ion Physics and Applied Physics, University of Innsbruck, A-6020 Innsbruck (Austria)] [Institute for Ion Physics and Applied Physics, University of Innsbruck, A-6020 Innsbruck (Austria)

    2013-08-15T23:59:59.000Z

    The high current regime of a magnetron-type discharge has been investigated. The discharge uses a permanent magnet as a cold cathode which emits secondary electrons while the chamber wall or a grounded electrode serves as the anode. As the discharge voltage is increased, the magnet develops cathode spots, which are short duration arcs that provide copious electrons to increase the discharge current dramatically. Short (1 ?s), high current (200 A) and high voltage (750 V) discharge pulses are produced in a relaxation instability between the plasma and a charging capacitor. Spots are also observed on a negatively biased plane Langmuir probe. The probe current pulses are as large as those on the magnet, implying that the high discharge current does not depend on the cathode surface area but on the properties of the spots. The fast current pulses produce large inductive voltages, which can reverse the electrical polarity of the magnet and temporarily operate it as an anode. The discharge current may also oscillate at the frequency determined by the charging capacitor and the discharge circuit inductance. Each half cycle of high-current current pulses exhibits a fast (?10 ns) current rise when a spot is formed. It induces high frequency (10–100 MHz) transients and ringing oscillations in probes and current circuits. Most probes behave like unmatched antennas for the electromagnetic pulses of spot discharges. Examples are shown to distinguish the source of oscillations and some rf characteristics of Langmuir probes.

  18. Light Computing

    E-Print Network [OSTI]

    Gordon Chalmers

    2006-10-13T23:59:59.000Z

    A configuration of light pulses is generated, together with emitters and receptors, that allows computing. The computing is extraordinarily high in number of flops per second, exceeding the capability of a quantum computer for a given size and coherence region. The emitters and receptors are based on the quantum diode, which can emit and detect individual photons with high accuracy.

  19. Observations of a mode transition in a hydrogen hollow cathode discharge using phase resolved optical emission spectroscopy

    SciTech Connect (OSTI)

    Dixon, Sam, E-mail: sam.dixon@anu.edu.au; Charles, Christine; Dedrick, James; Boswell, Rod [Space Plasma, Power and Propulsion Laboratory, Research School of Physics and Engineering, The Australian National University, Canberra ACT 0200 (Australia); Gans, Timo; O'Connell, Deborah [Department of Physics, York Plasma Institute, University of York, Heslington, York YO10 5DD (United Kingdom)

    2014-07-07T23:59:59.000Z

    Two distinct operational modes are observed in a radio frequency (rf) low pressure hydrogen hollow cathode discharge. The mode transition is characterised by a change in total light emission and differing expansion structures. An intensified CCD camera is used to make phase resolved images of Balmer ? emission from the discharge. The low emission mode is consistent with a typical ? discharge, and appears to be driven by secondary electrons ejected from the cathode surface. The bright mode displays characteristics common to an inductive discharge, including increased optical emission, power factor, and temperature of the H{sub 2} gas. The bright mode precipitates the formation of a stationary shock in the expansion, observed as a dark region adjacent to the source-chamber interface.

  20. Baker-Barry Tunnel Lighting: Evaluation of a Potential GATEWAY Demonstrations Project

    SciTech Connect (OSTI)

    Tuenge, Jason R.

    2011-06-28T23:59:59.000Z

    The U.S. Department of Energy is evaluating the Baker-Barry Tunnel as a potential GATEWAY Demonstrations project for deployment of solid-state lighting (SSL) technology. The National Park Service views this project as a possible proving ground and template for implementation of light-emitting diode (LED) luminaires in other tunnels, thereby expanding the estimated 40% energy savings from 132 MWh/yr to a much larger figure nationally. Most of the energy savings in this application is attributable to the instant-restrike capability of LED products and to their high tolerance for frequent on/off switching, used here to separately control either end of the tunnel during daytime hours. Some LED luminaires rival or outperform their high-intensity discharge (HID) counterparts in terms of efficacy, but options are limited, and smaller lumen packages preclude true one-for-one equivalence. However, LED products continue to improve in efficacy and affordability at a rate unmatched by other light source technologies; the estimated simple payback period of eight years (excluding installation costs and maintenance savings) can be expected to improve with time. The proposed revisions to the existing high-pressure sodium (HPS) lighting system would require slightly increased controls complexity and significantly increased luminaire types and quantities. In exchange, substantial annual savings (from reduced maintenance and energy use) would be complemented by improved quantity and quality of illumination. Although advanced lighting controls could offer additional savings, it is unclear whether such a system would prove cost-effective; this topic may be explored in future work.

  1. Light-driven phase shifter

    DOE Patents [OSTI]

    Early, James W. (Los Alamos, NM)

    1990-01-01T23:59:59.000Z

    A light-driven phase shifter is provided for modulating a transmission light beam. A gaseous medium such as argon is provided with electron energy states excited to populate a metastable state. A tunable dye laser is selected with a wavelength effective to deplete the metastable electron state and may be intensity modulated. The dye laser is directed through the gaseous medium to define a first optical path having an index of refraction determined by the gaseous medium having a depleted metastable electron state. A transmission laser beam is also directed through the gaseous medium to define a second optical path at least partially coincident with the first optical path. The intensity of the dye laser beam may then be varied to phase modulate the transmission laser beam.

  2. Accelerators for Intensity Frontier Research

    SciTech Connect (OSTI)

    Derwent, Paul; /Fermilab

    2012-05-11T23:59:59.000Z

    In 2008, the Particle Physics Project Prioritization Panel identified three frontiers for research in high energy physics, the Energy Frontier, the Intensity Frontier, and the Cosmic Frontier. In this paper, I will describe how Fermilab is configuring and upgrading the accelerator complex, prior to the development of Project X, in support of the Intensity Frontier.

  3. Dependence of recycling and edge profiles on lithium evaporation in high triangularity, high performance NSTX H-mode discharges

    E-Print Network [OSTI]

    Princeton Plasma Physics Laboratory

    1 Dependence of recycling and edge profiles on lithium evaporation in high triangularity, high between discharges in NSTX, partly to reduce recycling. Reduced D emissions from the lower and upper of the recycling light, improvements in global confinement16-19 , along with the appearance of ELM-free regimes20

  4. Repetitively pulsed VUV emitter pumped by a barrier discharge in a mixture of helium with heavy water (D{sub 2}O) vapour

    SciTech Connect (OSTI)

    Shuaibov, Aleksandr K; Minya, A I; Hrytsak, R V; Gomoki, Z T; Shevera, Igor' V [Uzhgorod National University, Uzhgorod (Ukraine)

    2012-08-31T23:59:59.000Z

    A gas-discharge lamp based on a barrier discharge in a He - D{sub 2}O mixture at partial pressures p{sub D2O} = 0.04 - 0.33 kPa and p{sub He} = 10 - 60 kPa is studied. The emission spectrum of the discharge plasma contains mainly the A {yields} X and C {yields} X bands of OD hydroxyl ({lambda} = 144 - 160 nm). The intensities of these bands are optimised by varying the pressure and composition of working mixtures. (laser applications and other topics in quantum electronics)

  5. Residual dust charges in discharge afterglow

    SciTech Connect (OSTI)

    Coueedel, L.; Mikikian, M.; Boufendi, L.; Samarian, A. A. [GREMI - Groupe de Recherches sur l'Energetique des Milieux Ionises, CNRS/Universite d'Orleans, 14 rue d'Issoudun, 45067 Orleans Cedex 2 (France); School of Physics A28, University of Sydney, NSW 2006 (Australia)

    2006-08-15T23:59:59.000Z

    An on-ground measurement of dust-particle residual charges in the afterglow of a dusty plasma was performed in a rf discharge. An upward thermophoretic force was used to balance the gravitational force. It was found that positively charged, negatively charged, and neutral dust particles coexisted for more than 1 min after the discharge was switched off. The mean residual charge for 200-nm-radius particles was measured. The dust particle mean charge is about -5e at a pressure of 1.2 mbar and about -3e at a pressure of 0.4 mbar.

  6. Gregorian optical system with non-linear optical technology for protection against intense optical transients

    DOE Patents [OSTI]

    Ackermann, Mark R. (Albuquerque, NM); Diels, Jean-Claude M. (Albuquerque, NM)

    2007-06-26T23:59:59.000Z

    An optical system comprising a concave primary mirror reflects light through an intermediate focus to a secondary mirror. The secondary mirror re-focuses the image to a final image plane. Optical limiter material is placed near the intermediate focus to optically limit the intensity of light so that downstream components of the optical system are protected from intense optical transients. Additional lenses before and/or after the intermediate focus correct optical aberrations.

  7. Lighting Inventory Lighting Theatre and Drama

    E-Print Network [OSTI]

    Indiana University

    Lighting Inventory Lighting Theatre and Drama Description Totals R.Halls Wells- Metz Light ERS ETC SourceFour 25 25 50 degree ERS Strand Lighting 64 14 24 12 14 36 degree ERS ETC Source Four 15 15 36 degree ERS Strand Lighting 124 60 58 2 4 26 degree ERS ETC SourceFour 2 2 26 degree ERS Strand

  8. ITP Energy Intensive Processes: Energy-Intensive Processes Portfolio...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    teChnologIes Program IntroduCtIon the research and development (r&d) portfolio for energy-Intensive Processes (eIP) addresses the top technology opportunities to save energy...

  9. Ternary gas mixture for diffuse discharge switch

    DOE Patents [OSTI]

    Christophorou, Loucas G. (Oak Ridge, TN); Hunter, Scott R. (Oak Ridge, TN)

    1988-01-01T23:59:59.000Z

    A new diffuse discharge gas switch wherein a mixture of gases is used to take advantage of desirable properties of the respective gases. There is a conducting gas, an insulating gas, and a third gas that has low ionization energy resulting in a net increase in the number of electrons available to produce a current.

  10. Electrostatic precipitator having high strength discharge electrode

    SciTech Connect (OSTI)

    Bakke, E.; Willett, H.P.

    1983-06-21T23:59:59.000Z

    There is disclosed an electrostatic precipitator with a discharge electrode having dimensional and configuration characteristics which provide high field strength and high current density particularly in a wet electrostatic precipitator. The round cylindrical collector tube of length (L) and with an inner diameter (D) has a coaxially positioned discharge electrode having an electrode supporting mast of a diameter from 0.25 to 40 D with an electrically conducting closed screw fli secured to the mast. The screw flight has an overall diameter (D) of from 0.33 to 0.67 D with a pitch of from d-d/2 to d-d and an overall length of from one screw revolution to l-(D-d), preferably one-half L or less and most preferably one to two revolutions. The short screw flight is economical and readily adjusted. The screw flight has a thickness of from about 0.05 to 15 inch and has a symmetrically curved outer edge. Collector tube is flared at its lower end to direct water away from the electrode mast as the water is discharged from the tube. The discharge electrode is supported from above and centered by means of adjustable tie rods at its lower end.

  11. The electrodeless discharge at atmospheric pressure

    SciTech Connect (OSTI)

    Laroussi, M.

    1999-07-01T23:59:59.000Z

    Recently the generation and applications of atmospheric pressure plasmas received increased interest in the plasma research community. Applications such as the surface modification of materials, and the decontamination of matter have been under investigation. In this context, the authors introduce a new means of generating an atmospheric pressure discharge, which is suitable for use in the above-mentioned applications, and in the treatment of undesirable or polluting gases, such as VOC's. This device is a capacitively coupled discharge. It is basically made of a non-conducting tube with two independent loops of wire wrapped around it, and separated by a distance d. A stable discharge is generated inside the tube when an AC voltage of few hundred volts to few kilovolts, at a frequency of few kilohertz, is applied between the loops. One end of the tube is completely open to the outside air, and a seed gas (generally a noble gas such as Helium) is introduced in the tube. The plasma generated with this method is weakly ionized, cold, and is maintained by a relatively low input power (few tens of watts, depending on the size of the tube). In this paper, the discharge electrical characteristics, its radiation emission characteristics, and the measurement of relevant plasma parameters will be presented.

  12. Light Source

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: VegetationEquipment Surfaces and Interfaces Sample6, 2011 LawrenceEfeedstocks and the climateLife a Light

  13. Light' Darkness

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: VegetationEquipment Surfaces and Interfaces Sample6, 2011 LawrenceEfeedstocks and the climateLifeLight to

  14. Residential Lighting

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administration the1 -the Mid-Infrared atEffectquestionnairesU.S. EnergyEnergy EfficiencyLighting

  15. Resonant Visible Light Modulation with Graphene

    E-Print Network [OSTI]

    Yu, Renwen; de Abajo, F Javier Garcia

    2015-01-01T23:59:59.000Z

    Fast modulation and switching of light at visible and near-infrared (vis-NIR) frequencies is of utmost importance for optical signal processing and sensing technologies. No fundamental limit appears to prevent us from designing wavelength-sized devices capable of controlling the light phase and intensity at gigaherts (and even terahertz) speeds in those spectral ranges. However, this problem remains largely unsolved, despite recent advances in the use of quantum wells and phase-change materials for that purpose. Here, we explore an alternative solution based upon the remarkable electro-optical properties of graphene. In particular, we predict unity-order changes in the transmission and absorption of vis-NIR light produced upon electrical doping of graphene sheets coupled to realistically engineered optical cavities. The light intensity is enhanced at the graphene plane, and so is its absorption, which can be switched and modulated via Pauli blocking through varying the level of doping. Specifically, we explor...

  16. Snowmass 2013 Computing Frontier: Intensity Frontier

    E-Print Network [OSTI]

    B. Rebel; M. C. Sanchez; S. Wolbers

    2013-10-25T23:59:59.000Z

    The Intensity Frontier (IF) is a primary focus of the U.S.-based particle physics program. It encompasses a large spectrum of physics, including quark flavor physics, charged lepton processes, neutrinos, baryon number violation, new light weakly-coupled particles, and nucleons, nuclei and atoms. There are many experiments, a range of scales in data output and throughput, and a wide range in the number of experimenters. The experiments, projects and theory in this area all require demanding computing capabilities and technologies. The IF experiments have significant computing requirements for simulation, theory and modeling, beam line and experiment design, triggers and DAQ, online monitoring, event reconstruction and processing, and physics analysis. We have conducted a qualitative survey of the current and near-term future experiments in the IF to understand the computing demands of this area and their expected evolution. This report details the expected computing requirements for the IF in the context of the Snowmass Community Summer Study 2013.

  17. Light Water Reactor Sustainability

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    3 Light Water Reactor Sustainability Program ACCOMPLISHMENTS REPORT 2013 Accomplishments Report | Light Water Reactor Sustainability 2 T he mission of the Light Water Reactor...

  18. Light Water Reactor Sustainability

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    4 Light Water Reactor Sustainability ACCOMPLISHMENTS REPORT 2014 Accomplishments Report | Light Water Reactor Sustainability 2 T he mission of the Light Water Reactor...

  19. Neutral particle beam intensity controller

    DOE Patents [OSTI]

    Dagenhart, W.K.

    1984-05-29T23:59:59.000Z

    The neutral beam intensity controller is based on selected magnetic defocusing of the ion beam prior to neutralization. The defocused portion of the beam is dumped onto a beam dump disposed perpendicular to the beam axis. Selective defocusing is accomplished by means of a magnetic field generator disposed about the neutralizer so that the field is transverse to the beam axis. The magnetic field intensity is varied to provide the selected partial beam defocusing of the ions prior to neutralization. The desired focused neutral beam portion passes along the beam path through a defining aperture in the beam dump, thereby controlling the desired fraction of neutral particles transmitted to a utilization device without altering the kinetic energy level of the desired neutral particle fraction. By proper selection of the magnetic field intensity, virtually zero through 100% intensity control of the neutral beam is achieved.

  20. Iron and Steel Energy Intensities

    U.S. Energy Information Administration (EIA) Indexed Site

    If you are having trouble, call 202-586-8800 for help. Home > >Energy Users > Energy Efficiency Page > Iron and Steel Energy Intensities First Use of Energy Blue Bullet First Use...

  1. Multi-Wavelength Visible Light Communication System Design Pankil Butala 1a

    E-Print Network [OSTI]

    Little, Thomas

    -converted light emitting diodes, or by filtering to iso- late the blue component from these sources. Multi efficient illumination devices called light emitting diodes (LED). The intensity of radiant flux emitted

  2. Advanced Lighting Program Development (BG9702800) Final Report

    SciTech Connect (OSTI)

    Rubinstein, Francis; Johnson, Steve

    1998-02-01T23:59:59.000Z

    The report presents a long-range plan for a broad-based, coordinated research, development and market transformation program for reducing the lighting energy intensities in commercial and residential buildings in California without compromising lighting quality. An effective program to advance lighting energy efficiency in California must be based on an understanding that lighting is a mature field and the lighting industry has developed many specialized products that meet a wide variety of light needs for different building types. Above all else, the lighting field is diverse and there are applications for a wide range of lighting products, systems, and strategies. Given the range of existing lighting solutions, an effective energy efficient lighting research portfolio must be broad-based and diverse to match the diversity of the lighting market itself. The belief that there is one solution--a magic bullet, such as a better lamp, for example--that will propel lighting efficiency across all uses to new heights is, in the authors' opinion, an illusion. A multi-path program is the only effective means to raising lighting efficiency across all lighting applications in all building types. This report presents a list of 27 lighting technologies and concepts (key activities) that could form the basis of a coordinated research and market transformation plan for significantly reducing lighting energy intensities in California buildings. The total 27 key activities into seven broad classes as follows: Light sources; Ballasts; Luminaires; Lighting Controls; Lighting Systems in Buildings; Human Factors and Education. Each of the above technology classes is discussed in terms of background, key activities, and the energy savings potential for the state. The report concludes that there are many possibilities for targeted research, development, and market transformation activities across all sectors of the building lighting industry. A concerted investment by the state to foster efficiency improvements in lighting systems in commercial and residential buildings would have a major positive impact on energy use and environmental quality in California.

  3. Gamma radiation field intensity meter

    DOE Patents [OSTI]

    Thacker, L.H.

    1995-10-17T23:59:59.000Z

    A gamma radiation intensity meter measures dose rate of a radiation field. The gamma radiation intensity meter includes a tritium battery emitting beta rays generating a current which is essentially constant. Dose rate is correlated to an amount of movement of an electroscope element charged by the tritium battery. Ionizing radiation decreases the voltage at the element and causes movement. A bleed resistor is coupled between the electroscope support element or electrode and the ionization chamber wall electrode. 4 figs.

  4. Gamma radiation field intensity meter

    DOE Patents [OSTI]

    Thacker, L.H.

    1994-08-16T23:59:59.000Z

    A gamma radiation intensity meter measures dose rate of a radiation field. The gamma radiation intensity meter includes a tritium battery emitting beta rays generating a current which is essentially constant. Dose rate is correlated to an amount of movement of an electroscope element charged by the tritium battery. Ionizing radiation decreases the voltage at the element and causes movement. A bleed resistor is coupled between the electroscope support element or electrode and the ionization chamber wall electrode. 4 figs.

  5. Gamma radiation field intensity meter

    DOE Patents [OSTI]

    Thacker, Louis H. (Knoxville, TN)

    1995-01-01T23:59:59.000Z

    A gamma radiation intensity meter measures dose rate of a radiation field. The gamma radiation intensity meter includes a tritium battery emitting beta rays generating a current which is essentially constant. Dose rate is correlated to an amount of movement of an electroscope element charged by the tritium battery. Ionizing radiation decreases the voltage at the element and causes movement. A bleed resistor is coupled between the electroscope support element or electrode and the ionization chamber wall electrode.

  6. Gamma radiation field intensity meter

    DOE Patents [OSTI]

    Thacker, Louis H. (Knoxville, TN)

    1994-01-01T23:59:59.000Z

    A gamma radiation intensity meter measures dose rate of a radiation field. The gamma radiation intensity meter includes a tritium battery emitting beta rays generating a current which is essentially constant. Dose rate is correlated to an amount of movement of an electroscope element charged by the tritium battery. Ionizing radiation decreases the voltage at the element and causes movement. A bleed resistor is coupled between the electroscope support element or electrode and the ionization chamber wall electrode.

  7. Experimental investigation of electron multipactor discharges at very high frequency

    E-Print Network [OSTI]

    Graves, Timothy P. (Timothy Paul)

    2006-01-01T23:59:59.000Z

    Multipactor discharges are a resonant condition in which electrons impact a surface in phase with an alternating electric field. The discharge is sustained by electron multiplication from secondary emission. As motivation, ...

  8. Montana Facilities Which Do Not Discharge Process Wastewater...

    Open Energy Info (EERE)

    Which Do Not Discharge Process Wastewater (MDEQ Form 2E) Jump to: navigation, search OpenEI Reference LibraryAdd to library Form: Montana Facilities Which Do Not Discharge Process...

  9. LED Traffic Light as a Communications Device Grantham Pang, Thomas Kwan, Chi-Ho Chan, Hugh Liu.

    E-Print Network [OSTI]

    Pang, Grantham

    :http://www.eee.hku.hk/~gpang Abstract The visible light from an LED (light emitting diode) traffic light can be modulated and encoded on the description of an audio information system made up of high brightness, visible light emitting diodes (LEDs messages 1. Introduction Recently, high intensity light emitting diodes for traffic signals are available

  10. Excessive Balmer line broadening in a plane cathode abnormal glow discharge in hydrogen

    SciTech Connect (OSTI)

    Cvetanovic, N.; Kuraica, M.M.; Konjevic, N. [Center for Science and Development of Technology, Obilicev Venac 26, Belgrade, and Faculty of Transport and Traffic Engineering, University of Belgrade, V. Stepe 305, Belgrade (Serbia and Montenegro); Faculty of Physics, University of Belgrade, P.O. Box 368, 11001 Belgrade, and Center for Science and Development of Technology, Obilicev Venac 26, Belgrade (Serbia and Montenegro); Faculty of Physics, University of Belgrade, P.O. Box 368, 11001 Belgrade (Serbia and Montenegro)

    2005-02-01T23:59:59.000Z

    Results of a Doppler spectroscopy study of the hydrogen Balmer alpha line in an abnormal glow discharge operated in pure hydrogen are reported. Measurements of line shapes are performed side-on to the discharge axis in a low electric field region of negative glow. The excessive Balmer alpha broadening is detected and its presence and linewidth is related to the collisions of fast hydrogen atoms with molecular hydrogen. The collision model enabled also an estimation of effective cross section data from the Balmer alpha axial intensity decay curves. Large excessive Balmer alpha line broadening in pure hydrogen and its dependence upon the direction of observation with respect to the electric field is in contradiction to the resonance transfer model, proposed byMills et al. in several publications [see, e.g., IEEE Trans. Plasma Sci. 31, 338 (2003)].

  11. Fundamental limit of light trapping in grating Zongfu Yu, Aaswath Raman and Shanhui Fan+

    E-Print Network [OSTI]

    Fan, Shanhui

    ­305 (1982). 5. M. A. Green, "Lambertian light trapping in textured solar cells and light-emitting diodes. I. Tobías, A. Luque, and A. Marti, "Light intensity enhancement by diffracting structures in solar of nanophotonic light trapping for solar cells," arXiv:1004.2902v2 [physics.optics] (2010). http

  12. Classical light analogue of the nonlocal Aharonov-Bohm effect

    E-Print Network [OSTI]

    Nandan Satapathy; Deepak Pandey; Poonam Mehta; Supurna Sinha; Joseph Samuel; Hema Ramachandran

    2012-02-13T23:59:59.000Z

    We demonstrate the existence of a non-local geometric phase in the intensity-intensity correlations of classical incoherent light, that is not seen in the lower order correlations. This two-photon Pancharatnam phase was observed and modulated in a Mach-Zehnder interferometer. Using acousto-optic interaction, independent phase noise was introduced to light in the two arms of the interferometer to create two independent incoherent classical sources from laser light. The experiment is the classical optical analogue of the multi-particle Aharonov-Bohm effect. As the trajectory of light over the Poincare sphere introduces a phase shift observable only in the intensity-intensity correlation, it provides a means of deflecting the two-photon wavefront, while having no effect on single photons.

  13. Residual dust charges in discharge afterglow L. Couedel,

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    was performed in a rf discharge. An upward thermophoretic force was used to balance the gravitational force

  14. Sustainable Office Lighting Options

    E-Print Network [OSTI]

    Massachusetts at Amherst, University of

    Sustainable Office Lighting Options Task Lighting: Task lighting is a localized method of lighting a workspace so that additional, unnecessary lighting is eliminated, decreasing energy usage and costs. Illumination levels in the targeted work areas are higher with task lighting than with the ambient levels

  15. Gas mixture for diffuse-discharge switch

    DOE Patents [OSTI]

    Christophorou, L.G.; Carter, J.G.; Hunter, S.R.

    1982-08-31T23:59:59.000Z

    Gaseous medium in a diffuse-discharge switch of a high-energy pulse generator is formed of argon combined with a compound selected from the group consisting of CF/sub 4/, C/sub 2/F/sub 6/, C/sub 3/F/sub 8/, n-C/sub 4/F/sub 10/, WF/sub 6/, (CF/sub 3/)/sub 2/S and (CF/sub 3/)/sub 2/O.

  16. Device for imaging scenes with very large ranges of intensity

    DOE Patents [OSTI]

    Deason, Vance Albert (Idaho Falls, ID)

    2011-11-15T23:59:59.000Z

    A device for imaging scenes with a very large range of intensity having a pair of polarizers, a primary lens, an attenuating mask, and an imaging device optically connected along an optical axis. Preferably, a secondary lens, positioned between the attenuating mask and the imaging device is used to focus light on the imaging device. The angle between the first polarization direction and the second polarization direction is adjustable.

  17. Magnetism in Lithium–Oxygen Discharge Product

    SciTech Connect (OSTI)

    Lu, Jun; Jung, Hun-Ji; Lau, Kah Chun; Zhang, Zhengcheng; Schlueter, John A.; Du, Peng; Assary, Rajeev S.; Greeley, Jeffrey P.; Ferguson, Glen A.; Wang, Hsien-Hau; Hassoun, Jusef; Iddir, Hakim; Zhou, Jigang; Zuin, Lucia; Hu, Yongfeng; Sun, Yang-Kook; Scrosati, Bruno; Curtiss, Larry A.; Amine, Khalil

    2013-05-13T23:59:59.000Z

    Nonaqueous lithium–oxygen batteries have a much superior theoretical gravimetric energy density compared to conventional lithium-ion batteries, and thus could render long-range electric vehicles a reality. A molecular-level understanding of the reversible formation of lithium peroxide in these batteries, the properties of major/minor discharge products, and the stability of the nonaqueous electrolytes is required to achieve successful lithium–oxygen batteries. We demonstrate that the major discharge product formed in the lithium–oxygen cell, lithium peroxide, exhibits a magnetic moment. These results are based on dc-magnetization measurements and a lithium– oxygen cell containing an ether-based electrolyte. The results are unexpected because bulk lithium peroxide has a significant band gap. Density functional calculations predict that superoxide- type surface oxygen groups with unpaired electrons exist on stoichiometric lithium peroxide crystalline surfaces and on nanoparticle surfaces; these computational results are consistent with the magnetic measurement of the discharged lithium peroxide product as well as EPR measurements on commercial lithium peroxide. The presence of superoxide-type surface oxygen groups with spin can play a role in the reversible formation and decomposition of lithium peroxide as well as the reversible formation and decomposition of electrolyte molecules.

  18. Capacitor discharge process for welding braided cable

    DOE Patents [OSTI]

    Wilson, Rick D. (Corvallis, OR)

    1995-01-01T23:59:59.000Z

    A capacitor discharge process for welding a braided cable formed from a plurality of individual cable strands to a solid metallic electrically conductive member comprises the steps of: (a) preparing the electrically conductive member for welding by bevelling one of its end portions while leaving an ignition projection extending outwardly from the apex of the bevel; (b) clamping the electrically conductive member in a cathode fixture; (c) connecting the electrically conductive member clamped in the cathode fixture to a capacitor bank capable of being charged to a preselected voltage value; (d) preparing the braided cable for welding by wrapping one of its end portions with a metallic sheet to form a retaining ring operable to maintain the individual strands of the braided cable in fixed position within the retaining ring; (e) clamping the braided cable and the retaining ring as a unit in an anode fixture so that the wrapped end portion of the braided cable faces the ignition projection of the electrically conductive member; and (f) moving the cathode fixture towards the anode fixture until the ignition projection of the electrically conductive member contacts the end portion of the braided cable thereby allowing the capacitor bank to discharge through the electrically conductive member and through the braided cable and causing the electrically conductive member to be welded to the braided cable via capacitor discharge action.

  19. External magnetic field influence on H{sub {alpha}} line in abnormal glow discharge

    SciTech Connect (OSTI)

    Obradovic, B.M.; Dojcinovic, I.P.; Kuraica, M.M.; Puric, J. [Faculty of Physics, University of Belgrade, P.O. Box 368, 11001 Belgrade (Serbia and Montenegro) and Center for Science and Development of Technology, Obilicev Venac 26, 11001 Belgrade (Serbia and Montenegro)

    2006-04-03T23:59:59.000Z

    Influence of the external axial magnetic field on the hydrogen H{sub {alpha}} line profiles in an abnormal glow discharge has been studied. It has been found that the applied magnetic field predominantly increases the intensity of central component of the characteristic excessively broadened H{sub {alpha}} profile. Magnetic filed causes helical motion of electrons along the electric field lines and prolongs their trajectories increasing the number of collisions with matrix gas. This explains the increase of the central component of H{sub {alpha}} profile and can be regarded as an experimental proof for the main contribution of electron excitation to that part of the profile.

  20. Neutral particle beam intensity controller

    DOE Patents [OSTI]

    Dagenhart, William K. (Oak Ridge, TN)

    1986-01-01T23:59:59.000Z

    A neutral beam intensity controller is provided for a neutral beam generator in which a neutral beam is established by accelerating ions from an ion source into a gas neutralizer. An amplitude modulated, rotating magnetic field is applied to the accelerated ion beam in the gas neutralizer to defocus the resultant neutral beam in a controlled manner to achieve intensity control of the neutral beam along the beam axis at constant beam energy. The rotating magnetic field alters the orbits of ions in the gas neutralizer before they are neutralized, thereby controlling the fraction of neutral particles transmitted out of the neutralizer along the central beam axis to a fusion device or the like. The altered path or defocused neutral particles are sprayed onto an actively cooled beam dump disposed perpendicular to the neutral beam axis and having a central open for passage of the focused beam at the central axis of the beamline. Virtually zero therough 100% intensity control is achieved by varying the magnetic field strength without altering the ion source beam intensity or its species yield.

  1. Sensitive glow discharge ion source for aerosol and gas analysis

    DOE Patents [OSTI]

    Reilly, Peter T. A. (Knoxville, TN)

    2007-08-14T23:59:59.000Z

    A high sensitivity glow discharge ion source system for analyzing particles includes an aerodynamic lens having a plurality of constrictions for receiving an aerosol including at least one analyte particle in a carrier gas and focusing the analyte particles into a collimated particle beam. A separator separates the carrier gas from the analyte particle beam, wherein the analyte particle beam or vapors derived from the analyte particle beam are selectively transmitted out of from the separator. A glow discharge ionization source includes a discharge chamber having an entrance orifice for receiving the analyte particle beam or analyte vapors, and a target electrode and discharge electrode therein. An electric field applied between the target electrode and discharge electrode generates an analyte ion stream from the analyte vapors, which is directed out of the discharge chamber through an exit orifice, such as to a mass spectrometer. High analyte sensitivity is obtained by pumping the discharge chamber exclusively through the exit orifice and the entrance orifice.

  2. Phenomena of oscillations in atmospheric pressure direct current glow discharges

    SciTech Connect (OSTI)

    Liu, Fu-cheng [College of Physics Science and Technology, Hebei University, Baoding 071002 (China)] [College of Physics Science and Technology, Hebei University, Baoding 071002 (China); Yan, Wen; Wang, De-zhen [School of Physics and Optoelectronic Technology, Dalian University of Technology, Dalian 116024 (China)] [School of Physics and Optoelectronic Technology, Dalian University of Technology, Dalian 116024 (China)

    2013-12-15T23:59:59.000Z

    Self-sustained oscillations in a dc glow discharge with a semiconductor layer at atmospheric pressure were investigated by means of a one-dimensional fluid model. It is found that the dc glow discharge initially becomes unstable in the subnormal glow region and gives rise to oscillations of plasma parameters. A variety of oscillations with one or more frequencies have been observed under different conditions. The discharge oscillates between the glow discharge mode and the Townsend discharge mode in the oscillations with large amplitude while operates in the subnormal glow discharge mode all the while in the oscillations with small amplitude. Fourier Transform spectra of oscillations reveal the transition mechanism between different oscillations. The effects of semiconductor conductivity on the oscillation frequency of the dominant mode, gas voltage, as well as the discharge current have also been analyzed.

  3. Nonlinear propagation of light in Dirac matter

    SciTech Connect (OSTI)

    Eliasson, Bengt [Institut fuer Theoretische Physik, Fakultaet fuer Physik und Astronomie, Ruhr-Universitaet Bochum, D-44780 Bochum (Germany); Shukla, P. K. [RUB International Chair, International Centre for Advanced Studies in Physical Sciences, Fakultaet fuer Physik und Astronomie, Ruhr-Universitaet Bochum, D-44780 Bochum (Germany)

    2011-03-15T23:59:59.000Z

    The nonlinear interaction between intense laser light and a quantum plasma is modeled by a collective Dirac equation coupled with the Maxwell equations. The model is used to study the nonlinear propagation of relativistically intense laser light in a quantum plasma including the electron spin-1/2 effect. The relativistic effects due to the high-intensity laser light lead, in general, to a downshift of the laser frequency, similar to a classical plasma where the relativistic mass increase leads to self-induced transparency of laser light and other associated effects. The electron spin-1/2 effects lead to a frequency upshift or downshift of the electromagnetic (EM) wave, depending on the spin state of the plasma and the polarization of the EM wave. For laboratory solid density plasmas, the spin-1/2 effects on the propagation of light are small, but they may be significant in superdense plasma in the core of white dwarf stars. We also discuss extensions of the model to include kinetic effects of a distribution of the electrons on the nonlinear propagation of EM waves in a quantum plasma.

  4. State waste discharge permit application: Hydrotest, maintenance and construction discharges. Revision 0

    SciTech Connect (OSTI)

    NONE

    1995-11-01T23:59:59.000Z

    On December 23, 1991, the US DOE< Richland Operation Office (RL) and the Washington State Department of Ecology (Ecology) agreed to adhere to the provisions of the Department of Ecology Consent Order No. DE91NM-177 (216 Consent Order) (Ecology and US DOE 1991). The 216 Consent Order list regulatory milestones for liquid effluent streams at the Hanford Site and requires compliance with the permitting requirements of Washington Administrative Code. Hanford Site liquid effluent streams discharging to the soil column have been categorized on the 216 Consent Order as follows: Phase I Streams; Phase II Streams; Miscellaneous Streams. Phase I and Phase II Streams were initially addressed in two report. Miscellaneous Streams are subject to the requirements of several milestones identified in the 216 Consent Order. This document constitutes the Categorical State Waste Discharge Permit application for hydrotest,maintenance and construction discharges throughout the Hanford Site. This categorical permit application form was prepared and approved by Ecology.

  5. X-ray intensity interferometer for undulator radiation

    SciTech Connect (OSTI)

    Gluskin, E.; McNulty, I.; Viccaro, P.J. [Argonne National Lab., IL (United States); Howells, M.R. [Lawrence Berkeley Lab., CA (United States)

    1991-12-31T23:59:59.000Z

    Intensity interferometry is well established with visible light but has never been demonstrated with x-radiation. We propose to measure the transverse coherence of an x-ray beam, for the first time, using the method of Hanbury Brown and Twiss. The x-ray interferometer consists of an array of slits, a grazing incidence reflective beamsplitter, a pair of fast multichannel plate detectors and a broadband, low-noise correlator circuit. The NSLS X1 or X13 soft x-ray undulator will supply the partially coherent x-rays. We are developing this technique to characterize the coherence properties of x-ray beams from high brilliance insertion devices at third-generation synchrotron light facilities such as the Advanced Photon Source and the Advanced Light Source. 17 refs.

  6. X-ray intensity interferometer for undulator radiation

    SciTech Connect (OSTI)

    Gluskin, E.; McNulty, I.; Viccaro, P.J. (Argonne National Lab., IL (United States)); Howells, M.R. (Lawrence Berkeley Lab., CA (United States))

    1991-01-01T23:59:59.000Z

    Intensity interferometry is well established with visible light but has never been demonstrated with x-radiation. We propose to measure the transverse coherence of an x-ray beam, for the first time, using the method of Hanbury Brown and Twiss. The x-ray interferometer consists of an array of slits, a grazing incidence reflective beamsplitter, a pair of fast multichannel plate detectors and a broadband, low-noise correlator circuit. The NSLS X1 or X13 soft x-ray undulator will supply the partially coherent x-rays. We are developing this technique to characterize the coherence properties of x-ray beams from high brilliance insertion devices at third-generation synchrotron light facilities such as the Advanced Photon Source and the Advanced Light Source. 17 refs.

  7. Mobile lighting apparatus

    DOE Patents [OSTI]

    Roe, George Michael; Klebanoff, Leonard Elliott; Rea, Gerald W; Drake, Robert A; Johnson, Terry A; Wingert, Steven John; Damberger, Thomas A; Skradski, Thomas J; Radley, Christopher James; Oros, James M; Schuttinger, Paul G; Grupp, David J; Prey, Stephen Carl

    2013-05-14T23:59:59.000Z

    A mobile lighting apparatus includes a portable frame such as a moveable trailer or skid having a light tower thereon. The light tower is moveable from a stowed position to a deployed position. A hydrogen-powered fuel cell is located on the portable frame to provide electrical power to an array of the energy efficient lights located on the light tower.

  8. Analysis of radiofrequency discharges in plasma

    DOE Patents [OSTI]

    Kumar, D.; McGlynn, S.P.

    1992-08-04T23:59:59.000Z

    Separation of laser optogalvanic signals in plasma into two components: (1) an ionization rate change component, and (2) a photoacoustic mediated component. This separation of components may be performed even when the two components overlap in time, by measuring time-resolved laser optogalvanic signals in an rf discharge plasma as the rf frequency is varied near the electrical resonance peak of the plasma and associated driving/detecting circuits. A novel spectrometer may be constructed to make these measurements. Such a spectrometer would be useful in better understanding and controlling such processes as plasma etching and plasma deposition. 15 figs.

  9. EK101 Engineering Light Smart Lighting

    E-Print Network [OSTI]

    Bifano, Thomas

    EK101 Engineering Light Smart Lighting Homework for 9/10 1. Make an estimate (using if the patent is granted.) 3. What is a lumen? A lux? How are the two related? How would you use a lux meter, (Lux, Lumens/m2) Luminous Flux: Perceivable light power from a source, (Lumens) Use the lux meter

  10. Neutrino physics with an intense \

    E-Print Network [OSTI]

    R. Henning

    2010-11-16T23:59:59.000Z

    We study some of the physics potential of an intense $1\\,\\mathrm{MCi}$ $^{51}\\mathrm{Cr}$ source combined with the {\\sc Majorana Demonstrator} enriched germanium detector array. The {\\sc Demonstrator} will consist of detectors with ultra-low radioactive backgrounds and extremely low energy thresholds of~$\\sim 400\\,\\mathrm{eV}$. We show that it can improve the current limit on the neutrino magnetic dipole moment. We briefly discuss physics applications of the charged-current reaction of the $^{51}\\mathrm{Cr} neutrino with the $^{73}\\mathrm{Ge} isotope. Finally, we argue that the rate from a realistic, intense tritium source is below the detectable limit of even a tonne-scale HPGe experiment

  11. Specific light in sculpture

    E-Print Network [OSTI]

    Powell, John William

    1989-01-01T23:59:59.000Z

    Specific light is defined as light from artificial or altered natural sources. The use and manipulation of light in three dimensional sculptural work is discussed in an historic and contemporary context. The author's work ...

  12. Low current plasmatron fuel converter having enlarged volume discharges

    DOE Patents [OSTI]

    Rabinovich, Alexander (Swampscott, MA); Alexeev, Nikolai (Moscow, RU); Bromberg, Leslie (Sharon, MA); Cohn, Daniel R. (Chestnut Hill, MA); Samokhin, Andrei (Moscow, RU)

    2009-10-06T23:59:59.000Z

    A novel apparatus and method is disclosed for a plasmatron fuel converter ("plasmatron") that efficiently uses electrical energy to produce hydrogen rich gas. The volume and shape of the plasma discharge is controlled by a fluid flow established in a plasma discharge volume. A plasmatron according to this invention produces a substantially large effective plasma discharge volume allowing for substantially greater volumetric efficiency in the initiation of chemical reactions within a volume of bulk fluid reactant flowing through the plasmatron.

  13. Point Source Discharges to Surface Waters (North Carolina)

    Broader source: Energy.gov [DOE]

    This rule requires permits for control of sources of water pollution by providing the requirements and procedures for application and issuance of state National Pollutant Discharge Elimination...

  14. Design of a high precision desktop wire electrical discharge machine.

    E-Print Network [OSTI]

    Dunlop, David James

    2010-01-01T23:59:59.000Z

    ??This thesis discusses the design of a wire electrical discharge machine that is small enough to be deemed a desktop machine that achieves sub micron… (more)

  15. The Physiologic Effects of Multiple Simultaneous Electronic Control Device Discharges

    E-Print Network [OSTI]

    Dawes, Donald M.; Ho, Jeffrey D; Reardon, Robert F; Sweeney, James D; Miner, James R

    2010-01-01T23:59:59.000Z

    physiologic effects of conducted electrical weapon dischargePhysiological effects of a conducted electrical weapon onLL, et al. Respiratory effect of prolonged electrical weapon

  16. atmospheric pressure discharge: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    de 367 Journal of Photochemistry and Photobiology A: Chemistry 140 (2001) 185189 The electrodeless discharge lamp: a prospective tool for photochemistry Chemistry Websites...

  17. atmospheric pressure discharges: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    de 367 Journal of Photochemistry and Photobiology A: Chemistry 140 (2001) 185189 The electrodeless discharge lamp: a prospective tool for photochemistry Chemistry Websites...

  18. Oklahoma Pollutant Discharge Elimination System (OPDES) Standards (Oklahoma)

    Broader source: Energy.gov [DOE]

    This program of the Water Quality Division of the Department of Environmental Quality sets the point source, biosolids (sewage sludge), and stormwater permitting standards for discharges to the...

  19. Notice of Intent (NOI) for Storm Water Discharges Associated...

    Open Energy Info (EERE)

    Intent (NOI) for Storm Water Discharges Associated with Construction Activities under TPDES General Permit (TXR150000) Jump to: navigation, search OpenEI Reference LibraryAdd to...

  20. WAC - 173 - 221 - Discharge Standards and Effluent Limitations...

    Open Energy Info (EERE)

    WAC - 173 - 221 - Discharge Standards and Effluent Limitations for Domestic Wastewater Facilities Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document-...

  1. File:CDPHE Industrial Individual Wastewater Discharge Permit...

    Open Energy Info (EERE)

    Industrial Individual Wastewater Discharge Permit Application.pdf Jump to: navigation, search File File history File usage Metadata File:CDPHE Industrial Individual Wastewater...

  2. atmospheric glow discharge: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    34 Glow Discharge Enhanced Chemical Reaction: Application in Ammonia Synthesis and Hydrocarbon Gas Cleanup Texas A&M University - TxSpace Summary: ......

  3. ablation glow discharge: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    29 Glow Discharge Enhanced Chemical Reaction: Application in Ammonia Synthesis and Hydrocarbon Gas Cleanup Texas A&M University - TxSpace Summary: ......

  4. analytical glow discharge: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    29 Glow Discharge Enhanced Chemical Reaction: Application in Ammonia Synthesis and Hydrocarbon Gas Cleanup Texas A&M University - TxSpace Summary: ......

  5. Hydrothermal Heat Discharge In The Cascade Range, Northwestern...

    Open Energy Info (EERE)

    based on the degree of geothermal warming (after correction for gravitational potential energy effects) and totals 660 MW. Fumarolic heat discharge is calculated by a variety...

  6. Stripe Turing structures in a two-dimensional gas discharge system

    SciTech Connect (OSTI)

    Ammelt, E.; Astrov, Y.A.; Purwins, H.G., [Institute of Applied Physics, University of Muenster, Corrensstrasse 2/4, D-48149 Muenster (Germany); Astrov, Y.A., [Joffe Physical-Technical Institute of the Russian Academy of Sciences, 194021 St. Petersburg (Russia)

    1997-06-01T23:59:59.000Z

    Pattern formation phenomena in current density distributions have been investigated experimentally in a dc-driven planar gas discharge semiconductor system. Patterns are observed and recorded via a light density distribution in the discharge gap, which can be seen through one of the electrodes. Under appropriate conditions the spatially homogeneous discharge glow undertakes a transition into hexagonal or striped patterns as the global current is increased. The observed phenomena are interpreted as a Turing bifurcation into a patterned state. The transition into a striped pattern is studied in detail. Transitions both to stationary and to slowly moving stripe patterns have been observed. It has been ascertained that the typical velocity of stripes, which is of the order of mm/s, is independent of the distance from the bifurcation point in a rather broad range of variation of the bifurcation parameter. The underlying mechanism of pattern formation, as well as the movement of the patterns, is discussed. {copyright} {ital 1997} {ital The American Physical Society}

  7. Intensive Observation Period Projects Scheduled

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation ProposedUsingFunInfrared Land SurfaceVirus-InfectedIntelligent Coatings forIntel®1 Intensive

  8. Wavelength-resolved low-frequency noise of GaInN/GaN green light emitting diodes

    E-Print Network [OSTI]

    Wetzel, Christian M.

    Wavelength-resolved low-frequency noise of GaInN/GaN green light emitting diodes S. L. Rumyantseva well light emitting diodes. The light intensity noise was measured as a function of wavelength within the light emitting diode spectral emission line. The spectral noise density is found to increase

  9. Ordered dust structures in a glow discharge

    SciTech Connect (OSTI)

    Karasev, V. Yu., E-mail: plasmadust@yandex.ru; Ivanov, A. Yu.; Dzlieva, E. S.; Eikhval'd, A. I. [St. Petersburg State University, Institute of Physics (Russian Federation)

    2008-02-15T23:59:59.000Z

    Highly ordered three-dimensional dust structures are created in a striated glow discharge, and their horizontal cross-sectional images are analyzed. Calculated correlation functions, local correlation parameters, and corresponding approximations are used to classify the state of a structure according to the Kosterlitz-Thouless-Halperin-Nelson-Young (KTHNY) two-dimensional melting theory and a phenomenological approach. An orientational map based on an orientational parameter is proposed to expose domains in a cross section of a structure. It is shown that a plasma crystal is a polycrystal consisting of hexagonal domains (crystallites). Thermophoretic forces are used to create corners of various angles in the perimeter of the structure. Transition between hexagonal and square cell shapes is observed.

  10. Extreme-UV electrical discharge source

    DOE Patents [OSTI]

    Fornaciari, Neal R. (Tracey, CA); Nygren, Richard E. (Los Ranchos de Albuquerque, NM); Ulrickson, Michael A. (Albuquerque, NM)

    2002-01-01T23:59:59.000Z

    An extreme ultraviolet and soft x-ray radiation electric capillary discharge source that includes a boron nitride housing defining a capillary bore that is positioned between two electrodes one of which is connected to a source of electric potential can generate a high EUV and soft x-ray radiation flux from the capillary bore outlet with minimal debris. The electrode that is positioned adjacent the capillary bore outlet is typically grounded. Pyrolytic boron nitride, highly oriented pyrolytic boron nitride, and cubic boron nitride are particularly suited. The boron nitride capillary bore can be configured as an insert that is encased in an exterior housing that is constructed of a thermally conductive material. Positioning the ground electrode sufficiently close to the capillary bore outlet also reduces bore erosion.

  11. General Conditions Applicable to Water Discharge Permits and Procedures and Criteria for Issuing Water Discharge Permits (Connecticut)

    Broader source: Energy.gov [DOE]

    These regulations describe permit and facility requirements for facilities which discharge wastewater. Facility construction, expansion, alteration, production increases, or process modifications...

  12. Lighting and Daylight Harvesting

    E-Print Network [OSTI]

    Bos, J.

    2011-01-01T23:59:59.000Z

    exposing us to the latest products and technologies. Daylight Harvesting A system of controlling the direction and the quantity of light both natural and artificial within a given space. This implies: Control of fenestration in terms of size..., transmission and direction. Control of reflected light within a space. Control of electric light in terms of delivery and amount Daylight harvesting systems are typically designed to maintain a minimum recommended light level. This light level...

  13. Comparison Of Expected Yields For Light Radioactive Beams At SPIRAL-1 And 2

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Comparison Of Expected Yields For Light Radioactive Beams At SPIRAL-1 And 2 Saint-Laurent M of this contribution is the comparison of yields expected for light radioactive beams at SPIRAL-1 and after an upgrade, Switzerland. Abstract. Light-particles stable high-intensity beams (p, d, 3,4 He...) will be available from

  14. Phase matrix for light scattering by concentrically stratified spheres: comparison of geometric

    E-Print Network [OSTI]

    Takano, Yoshihide

    Phase matrix for light scattering by concentrically stratified spheres: comparison of geometric for the evaluation of intensity and polarization of a light ray, which can undergo (1) external reflec- tion, (2) two this concept to light scattering by nonspherical and irregular ice particles [2,3]. To the best of our

  15. State Waste Discharge Permit application for industrial discharge to land: 200 East Area W-252 streams

    SciTech Connect (OSTI)

    Not Available

    1993-12-01T23:59:59.000Z

    This document constitutes the WAC 173-216 State Waste Discharge Permit application for six W-252 liquid effluent streams at the Hanford Site. Appendices B through H correspond to Section B through H in the permit application form. Within each appendix, sections correspond directly to the respective questions on the application form. The appendices include: Product or service information; Plant operational characteristics; Water consumption and waterloss; Wastewater information; Stormwater; Other information; and Site assessment.

  16. Relationships among probability distributions of stream discharges in floods, climate,

    E-Print Network [OSTI]

    Mojzsis, Stephen J.

    Relationships among probability distributions of stream discharges in floods, climate, bed load of both follow power laws. The number N(Q) of days on which the discharge exceeds Q, or the number of the United States. To examine the effect of climate change on bed load transport and river incision, we

  17. Discharge indices for water quality loads Richard M. Vogel

    E-Print Network [OSTI]

    Vogel, Richard M.

    : effective discharge, transport, sediment, constituents, rating curve, half-load Citation: Vogel, R. M., J. RDischarge indices for water quality loads Richard M. Vogel Department of Civil and Environmental load is ultimately the quantity of interest, we define a new index, the half-load discharge, which

  18. Faraday Accelerator with Radio-frequency Assisted Discharge (FARAD)

    E-Print Network [OSTI]

    Choueiri, Edgar

    rights reserved. #12;Abstract A new electrodeless accelerator concept, called Faraday Accelerator with Radio-frequency Assisted Discharge (FARAD), that relies on an RF-assisted discharge to produce a plasma, an applied magnetic field to guide the plasma into the acceleration region, and an induced current sheet

  19. An ultra miniature pinch-focus discharge Leopoldo Soto1

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Abstract As a way to investigate the minimum energy to produce a pinch plasma focus discharge, an ultra optimized plasma foci. It is interesting note that plasma parameters practically constant in plasma focusAn ultra miniature pinch-focus discharge Leopoldo Soto1 , Cristian Pavez1, 2 , Mario Barbaglia3

  20. State Waste Discharge Permit application: 200-E Powerhouse Ash Pit

    SciTech Connect (OSTI)

    Atencio, B.P.

    1994-06-01T23:59:59.000Z

    As part of the Hanford Federal Facility Agreement and Consent Order negotiations, the US Department and Energy, Richland Operations Office, the US Environmental Protection Agency, and the Washington State Department of Ecology agreed that liquid effluent discharges to the ground on the Hanford Site which affect groundwater or have the potential to affect groundwater would be subject to permitting under the structure of Chapter 173-216 (or 173-218 where applicable) of the Washington Administrative Code, the State Waste Discharge Permit Program. This document constitutes the State Waste Discharge Permit application for the 200-E Powerhouse Ash Pit. The 200-E Powerhouse Ash Waste Water discharges to the 200-E Powerhouse Ash Pit via dedicated pipelines. The 200-E Ash Waste Water is the only discharge to the 200-E Powerhouse Ash Pit. The 200-E Powerhouse is a steam generation facility consisting of a coal-handling and preparation section and boilers.

  1. State Waste Discharge Permit application: 200-W Powerhouse Ash Pit

    SciTech Connect (OSTI)

    Atencio, B.P.

    1994-06-01T23:59:59.000Z

    As part of the Hanford Federal Facility Agreement and Consent Order negotiations; the US Department of Energy, Richland Operations Office, the US Environmental Protection Agency, and the Washington State Department of Ecology agreed that liquid effluent discharges to the ground on the Hanford Site which affect groundwater or have the potential to affect groundwater would be subject to permitting under the structure of Chapter 173-216 (or 173-218 where applicable) of the Washington Administrative Code, the State Waste Discharge Permit Program. This document constitutes the State Waste Discharge Permit application for the 200-W Powerhouse Ash Pit. The 200-W Powerhouse Ash Waste Water discharges to the 200-W Powerhouse Ash Pit via dedicated pipelines. The 200-W Powerhouse Ash Waste Water is the only discharge to the 200-W Powerhouse Ash Pit. The 200-W Powerhouse is a steam generation facility consisting of a coal-handling and preparation section and boilers.

  2. State Waste Discharge Permit application: 400 Area Septic System

    SciTech Connect (OSTI)

    Not Available

    1994-06-01T23:59:59.000Z

    As part of the Hanford Federal Facility Agreement and Consent Order negotiations, the US Department of Energy, Richland Operations Office, the US Environmental Protection Agency, and the Washington State Department of Ecology agreed that liquid effluent discharges to the ground on the Hanford Site which affects groundwater or has the potential to affect groundwater would be subject to permitting under the structure of Chapter 173-216 (or 173-218 where applicable) of the Washington Administrative Code, the State Waste Discharge Permit Program. This document constitutes the State Waste Discharge Permit application for the 400 Area Septic System. The influent to the system is domestic waste water. Although the 400 Area Septic System is not a Public Owned Treatment Works, the Public Owned Treatment Works application is more applicable than the application for industrial waste water. Therefore, the State Waste Discharge Permit application for Public Owned Treatment Works Discharges to Land was used.

  3. Intense terahertz emission from relativistic circularly polarized laser pulses interaction with overdense plasmas

    SciTech Connect (OSTI)

    Chen, Zi-Yu; Li, Xiao-Ya [National Key Laboratory of Shock Wave and Detonation Physics, Institute of Fluid Physics, China Academy of Engineering Physics, Mianyang 621900 (China)] [National Key Laboratory of Shock Wave and Detonation Physics, Institute of Fluid Physics, China Academy of Engineering Physics, Mianyang 621900 (China); Yu, Wei [Shanghai Institute of Optics and Fine Mechanics, Chinese Academy of Sciences, Shanghai 201800 (China)] [Shanghai Institute of Optics and Fine Mechanics, Chinese Academy of Sciences, Shanghai 201800 (China)

    2013-10-15T23:59:59.000Z

    During the interaction of a relativistic circularly polarized laser pulse with an overdense plasma target, the longitudinal motion of bunches of electrons under the action of light pressure and electrostatic restore force can emit intense terahertz (THz) pulses. This mechanism allows high pump laser intensity and large electron number participating in the emission. Two-dimensional particle-in-cell simulations are carried out to investigate the THz emission. The results suggest that such a source can produce remarkably intense THz pulses with energy of several mJ/sr and power of tens of gigawatts, which could find applications in nonlinear studies and relativistic laser-plasma interaction diagnostics.

  4. Fundamental physics on natures of the macroscopic vacuum under high intense electromagnetic fields with accelerators

    E-Print Network [OSTI]

    Kensuke Homma

    2009-11-30T23:59:59.000Z

    High intense electromagnetic fields can be unique probes to study natures of macroscopic vacua by themselves. Combining accelerators with the intense field can provide more fruitful probes which can neither be achieved by only intense fields nor only high energy accelerators. We will overview the natures of vacua which can be accessible via intense laser-laser and intense laser-electron interactions. In the case of the laser-laser interaction, we propose how to observe nonlinear QED effects and effects of new fields like light scalar and pseudo scalar fields which may contribute to a macroscopic nature of our universe such as dark energy. In the case of the laser-electron interaction, in addition to nonlinear QED effects, we can further discuss the nature of accelerating field in the vacuum where we can access physics related with event horizons such as Hawking-Unruh radiations. We will introduce a recent experimental trial to search for this kind of odd radiations.

  5. Electrodeless lighting RF power source development. Final report

    SciTech Connect (OSTI)

    NONE

    1996-08-30T23:59:59.000Z

    An efficient, solid state RF power source has been developed on this NICE project for exciting low power electrodeless lamp bulbs. This project takes full advantage of concurrent advances in electrodeless lamp technology. Electrodeless lamp lighting systems utilizing the sulfur based bulb type developed by Fusion Lighting, Inc., is an emerging technology which is based on generating light in a confined plasma created and sustained by RF excitation. The bulb for such a lamp is filled with a particular element and inert gas at low pressure when cold. RF power from the RF source creates a plasma within the bulb which reaches temperatures approaching those of high pressure discharge lamp plasmas. At these temperatures the plasma radiates substantial visible light with a spectrum similar to sunlight.

  6. Abundance and distribution of macro-crustaceans in the intake and discharge areas before and during early operation of the Cedar Bayou Generating Station

    E-Print Network [OSTI]

    Schmidt, Monroe

    1972-01-01T23:59:59.000Z

    and Discharge Areas Before and During Early Operation of the Cedar Bayou Generating Station. (May 1972) Monroe Schmidt, A. A. , Blinn College; B. S. , Texas A&M University Directed by: Dr. Kirk Strawn Two trawl and 1 seine station in Tabbs Bay, 2 trawl... were collected twice monthly from May through October 1970. Genera- tion of electric power (and discharge of heated water) by Unit 1, a 750 MW steam-electric unit of the Houston Lighting and Power Company's Cedar Bayou Generating Station, began...

  7. Kyler Nelson Light Timer

    E-Print Network [OSTI]

    Kachroo, Pushkin

    designated by the user, the Arduino board will dim the light to save energy. The user designates the time instance, the light is dimmed using pulse width modulation (PWM) in the Arduino's pin number 11

  8. Light-harvesting in bacteria exploits a critical interplay between transport and trapping dynamics

    E-Print Network [OSTI]

    Felipe Caycedo-Soler; Ferney J. Rodriguez; Luis Quiroga; Neil F. Johnson

    2010-03-11T23:59:59.000Z

    Light-harvesting bacteria Rhodospirillum Photometricum were recently found to adopt strikingly different architectures depending on illumination conditions. We present analytic and numerical calculations which explain this observation by quantifying a dynamical interplay between excitation transfer kinetics and reaction center cycling. High light-intensity membranes (HLIM) exploit dissipation as a photo-protective mechanism, thereby safeguarding a steady supply of chemical energy, while low light-intensity membranes (LLIM) efficiently process unused illumination intensity by channelling it to open reaction centers. More generally, our analysis elucidates and quantifies the trade-offs in natural network design for solar energy conversion.

  9. Properties of water surface discharge at different pulse repetition rates

    SciTech Connect (OSTI)

    Ruma,; Yoshihara, K. [Graduate School of Science and Technology, Kumamoto University, Kumamoto 860-8555 (Japan); Hosseini, S. H. R., E-mail: hosseini@kumamoto-u.ac.jp; Sakugawa, T.; Akiyama, H. [Graduate School of Science and Technology, Kumamoto University, Kumamoto 860-8555 (Japan); Institute of Pulsed Power Science, Kumamoto University, Kumamoto 860-8555 (Japan); Akiyama, M. [Department of Electrical and Electronic Engineering, Kagoshima University, Kagoshima 890-0065 (Japan); Lukeš, P. [Institute of Plasma Physics, AS CR, Prague, Prague 18200 (Czech Republic)

    2014-09-28T23:59:59.000Z

    The properties of water surface discharge plasma for variety of pulse repetition rates are investigated. A magnetic pulse compression (MPC) pulsed power modulator able to deliver pulse repetition rates up to 1000?Hz, with 0.5?J per pulse energy output at 25?kV, was used as the pulsed power source. Positive pulse with a point-to-plane electrode configuration was used for the experiments. The concentration and production yield of hydrogen peroxide (H{sub 2}O{sub 2}) were quantitatively measured and orange II organic dye was treated, to evaluate the chemical properties of the discharge reactor. Experimental results show that the physical and chemical properties of water surface discharge are not influenced by pulse repetition rate, very different from those observed for under water discharge. The production yield of H{sub 2}O{sub 2} and degradation rate per pulse of the dye did not significantly vary at different pulse repetition rates under a constant discharge mode on water surface. In addition, the solution temperature, pH, and conductivity for both water surface and underwater discharge reactors were measured to compare their plasma properties for different pulse repetition rates. The results confirm that surface discharge can be employed at high pulse repetition rates as a reliable and advantageous method for industrial and environmental decontamination applications.

  10. Regulations for the Rhode Island Pollutant Discharge Elimination System (Rhode Island)

    Broader source: Energy.gov [DOE]

    These regulations aim to protect surface water from pollutant discharges. They describe allowable discharges in the state that are subject to permits, discharges which may be made without permits,...

  11. A System-Level Electrostatic-Discharge-Protection Modeling Methodology for Time-

    E-Print Network [OSTI]

    Boyer, Edmond

    A System-Level Electrostatic-Discharge- Protection Modeling Methodology for Time- Domain Analysis. Index Terms--Electromagnetic compatibility (EMC), electrostatic discharge (ESD), modeling, system level precise simulations of electrostatic discharge (ESD) stress propagation on a printed circuit board (PCB

  12. AIRPORT LIGHTING Session Highlights

    E-Print Network [OSTI]

    Minnesota, University of

    AIRPORT LIGHTING Session Highlights In May 2002, the Airport Technical Assistance Program, also known as AirTAP, sponsored three airport-lighting training sessions at different locations in Minnesota information on airport lighting and navigational aid equipment selection, funding, maintenance, and operation

  13. Advanced Demand Responsive Lighting

    E-Print Network [OSTI]

    Advanced Demand Responsive Lighting Host: Francis Rubinstein Demand Response Research Center demand responsive lighting systems ­ Importance of dimming ­ New wireless controls technologies · Advanced Demand Responsive Lighting (commenced March 2007) #12;Objectives · Provide up-to-date information

  14. Light emitting device comprising phosphorescent materials for white light generation

    DOE Patents [OSTI]

    Thompson, Mark E.; Dapkus, P. Daniel

    2014-07-22T23:59:59.000Z

    The present invention relates to phosphors for energy downconversion of high energy light to generate a broadband light spectrum, which emit light of different emission wavelengths.

  15. Light Duty Combustion Research: Advanced Light-Duty Combustion...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Combustion Research: Advanced Light-Duty Combustion Experiments Light Duty Combustion Research: Advanced Light-Duty Combustion Experiments 2009 DOE Hydrogen Program and Vehicle...

  16. Plasma Acceleration from RF Discharge in Dielectric Capillary

    SciTech Connect (OSTI)

    A. Dunaevsky; Y. Raitses; N. J. Fisch

    2005-08-09T23:59:59.000Z

    Plasma acceleration from rf discharge in dielectric capillary was demonstrated. Observed plasma flow had ion energies of approximately 100 eV and electron energies of approximately 20 eV. The discharge was powered by a MHz-range rf generator and fed by Ar. Experimental results indicate possible validity of assumptions about formation of a potential difference at the open end of the capillary and presence of hot electron fraction in the capillary discharge. Simplicity and small dimensions of the source are attractive for micro-propulsion applications.

  17. Optical Emission of Dusty RF Discharges: Experiment and Simulation

    SciTech Connect (OSTI)

    Melzer, A.; Lewerentz, L.; Schneider, R. [Institute of Physics, University Greifswald, Felix-Hausdorff-Str. 6, 17489 Greifswald (Germany); Huebner, S. [Institute of Physics, University Greifswald, Felix-Hausdorff-Str. 6, 17489 Greifswald (Germany); Department of Applied Physics, Technical University Eindhoven, NL-5600 MB Eindhoven (Netherlands); Matyash, K. [Max-Planck-Institute for Plasma Physics, EURATOM Association, D-17491 Greifswald (Germany); Ikkurthi, V. R. [Institute for Plasma Research, Bhat, Ghandinagar, Gujarat (India)

    2011-11-29T23:59:59.000Z

    The spectral emission of argon atoms in a dusty radio frequence (RF) discharge has been investigated experimentally and in simulations. It was observed that the spatially and temporally resolved emission of the argon atoms in the dusty discharge was increased compared to the dust-free case during sheath expansion. The corresponding simulations have revealed that the dust trapped in the sheath of the discharge leads to a small, but important, increase of the amount of high-energy electrons that in turn leads to an increased argon emission.

  18. Entrainment by Spatiotemporal Chaos in Glow Discharge-Semiconductor Systems

    E-Print Network [OSTI]

    Marat Akhmet; Ismail Rafatov; Mehmet Onur Fen

    2014-06-15T23:59:59.000Z

    Entrainment of limit cycles by chaos [1] is discovered numerically through specially designed unidirectional coupling of two glow discharge-semiconductor systems. By utilizing the auxiliary system approach [2], it is verified that the phenomenon is not a chaos synchronization. Simulations demonstrate various aspects of the chaos appearance in both drive and response systems. Chaotic control is through the external circuit equation and governs the electrical potential on the boundary. The expandability of the theory to collectives of glow discharge systems is discussed, and this increases the potential of applications of the results. Moreover, the research completes the previous discussion of the chaos appearance in a glow discharge-semiconductor system [3].

  19. E-Print Network 3.0 - active liquid discharges Sample Search...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    discharge in synthetic air... Online at stacks.iop.orgJPhysD41035212 Abstract The barrier discharge in the coplanar ... Source: Greifswald, Ernst-Moritz-Arndt-Universitt...

  20. Permit Program Regulating Discharge of Nondomestic Wastewater into a POTW (Ohio)

    Broader source: Energy.gov [DOE]

    Any significant industrial user is required to apply for and obtain an individual indirect discharge permit if they discharge water or waste into a publicly owned treatment works.

  1. Characterization of Gatewell Orifice Lighting at the Bonneville Dam Second Powerhouse and Compendium of Research on Light Guidance with Juvenile Salmonids

    SciTech Connect (OSTI)

    Mueller, Robert P.; Simmons, Mary Ann

    2007-12-29T23:59:59.000Z

    The goal of the study described in this report is to provide U.S. Army Corps of Engineers (USACE) biologists and engineers with general design guidelines for using artificial lighting to enhance the passage of juvenile salmonids into the collection channel at the Bonneville Dam second powerhouse (B2). During fall 2007, Pacific Northwest National Laboratory (PNNL) researchers measured light levels in the field at one powerhouse orifice through which fish must pass to reach the collection channel. Two light types were evaluated—light-emitting diode (LED) lights and halogen spot lights. Additional measurements with mercury lamps were made at the PNNL Aquatic Research Laboratory to determine baseline intensity of the current lighting. A separate chapter synthesizes the relevant literature related to light and fish guidance for both field and laboratory studies. PNNL will also review the Corps plans for existing lighting protocol at all of the Portland District projects and help develop a uniform lighting scheme which could be implemented. The specific objectives for this study are to 1. Create a synthesis report of existing lighting data for juvenile salmonid attraction and deterrence and how the data are used at fish bypass facilities. 2. Evaluate current B2 orifice lighting conditions with both LED and halogen sources. 3. Make recommendations as to what lighting intensity, source, and configuration would improve passage at the B2 orifices. 4. Review USACE plans for retrofit of existing systems (to be assessed at a later date).

  2. Photonic crystal light source

    DOE Patents [OSTI]

    Fleming, James G. (Albuquerque, NM); Lin, Shawn-Yu (Albuquerque, NM); Bur, James A. (Corrales, NM)

    2004-07-27T23:59:59.000Z

    A light source is provided by a photonic crystal having an enhanced photonic density-of-states over a band of frequencies and wherein at least one of the dielectric materials of the photonic crystal has a complex dielectric constant, thereby producing enhanced light emission at the band of frequencies when the photonic crystal is heated. The dielectric material can be a metal, such as tungsten. The spectral properties of the light source can be easily tuned by modification of the photonic crystal structure and materials. The photonic crystal light source can be heated electrically or other heating means. The light source can further include additional photonic crystals that exhibit enhanced light emission at a different band of frequencies to provide for color mixing. The photonic crystal light source may have applications in optical telecommunications, information displays, energy conversion, sensors, and other optical applications.

  3. Light extraction from organic light-emitting diodes for lighting applications by sand-blasting

    E-Print Network [OSTI]

    Light extraction from organic light-emitting diodes for lighting applications by sand@ust.hk Abstract: Light extraction from organic light-emitting diodes (OLEDs) by scattering the light is one of the effective methods for large-area lighting applications. In this paper, we present a very simple and cost

  4. Discharging a DC bus capacitor of an electrical converter system

    DOE Patents [OSTI]

    Kajouke, Lateef A; Perisic, Milun; Ransom, Ray M

    2014-10-14T23:59:59.000Z

    A system and method of discharging a bus capacitor of a bidirectional matrix converter of a vehicle are presented here. The method begins by electrically shorting the AC interface of the converter after an AC energy source is disconnected from the AC interface. The method continues by arranging a plurality of switching elements of a second energy conversion module into a discharge configuration to establish an electrical current path from a first terminal of an isolation module, through an inductive element, and to a second terminal of the isolation module. The method also modulates a plurality of switching elements of a first energy conversion module, while maintaining the discharge configuration of the second energy conversion module, to at least partially discharge a DC bus capacitor.

  5. Use of microalgae to remove pollutants from power plant discharges

    DOE Patents [OSTI]

    Wilde, Edward W. (1833 Pisgah Rd., North Augusta, SC 29841); Benemann, John R. (2741 O'Harte, San Pablo, CA 94806); Weissman, Joseph C. (2086 N. Porpoise Pt. La., Vero Beach, FL 32963); Tillett, David M. (911-3 Coquina La., Vero Beach, FL 32963)

    1991-01-01T23:59:59.000Z

    A method and system for removing pollutants dissolved in the aqueous discharge of a plant, such as a power plant, from a body of water having known hydraulogy and physicochemical characteristics, the method comprising (a) modifying the hydraulic system of the body of water including use of physical barriers to define a zone in a portion of the body of water which zone includes the discharge point and where the water has a range of physicochemical characteristics; (b) selecting a large and preferably filamentous, planktonically growing strain of algae adapted to absorb the particular pollutants and genetically dominating algae at the physicochemical characteristics of the zone; (c) establishing a colony of the selected algal strain in the zone; (d) harvesting a portion of the colony; and (e) reinnoculating the zone near the discharge point with a fraction of the harvested portion. The fraction used for reinnoculation can be adjusted to balance the rate of pollutant removal to the rate of pollutant discharge.

  6. UPDES General Permit for Discharges from Construction Activities...

    Open Energy Info (EERE)

    Discharges from Construction Activities (Permit No. UTRC00000) Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- OtherOther: UPDES General Permit...

  7. AZPDES General Permit for Stormwater Discharges Associated with...

    Open Energy Info (EERE)

    Stormwater Discharges Associated with Construction Activity (Permit No. AZG2013-001) Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- OtherOther:...

  8. Energy Intensity Baselining and Tracking Guidance

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Learn more at betterbuildings.energy.gov Energy Intensity Baselining and Tracking Guidance i Preface The U.S. Department of Energy's (DOE) Better Buildings, Better Plants Program...

  9. Energy Intensity Baselining and Tracking Guidance

    Broader source: Energy.gov (indexed) [DOE]

    Learn more at betterbuildings.energy.gov Energy Intensity Baselining and Tracking Guidance i Preface The U.S. Department of Energy's (DOE's) Better Buildings, Better Plants Program...

  10. Gain-assisted superluminal light propagation via incoherent pump field

    E-Print Network [OSTI]

    M. Mahmoudi; S. Worya Rabiei; L. Safari; M. Sahrai

    2008-08-03T23:59:59.000Z

    We investigate the dispersion and the absorption properties of a weak probe field in a three-level Lambda-type atomic system. We use just an incoherent field for controlling the group velocity of light. It is shown that the slope of dispersion changes from positive to negative just with changing the intensity of the indirect incoherent pumping field. Gain-assisted superluminal light propagation appears in this system. No laser field is used in the pumping processes.

  11. SMART LIGHTING SYSTEMS ULTIMATE LIGHTING The Smart Lighting

    E-Print Network [OSTI]

    Linhardt, Robert J.

    Integration (Holistic Integrated Design) · Sensors as important as LEDs · Interconnected systems (human, building, grid) · Artistic Design Freedom · Lighting is Health, Entertainment, Information and Illumination Cost at any brightness · Chip level integrated electronics THE ERC RESEARCH COVERS THE ENTIRE SUPPLY

  12. World Best Practice Energy Intensity Values for Selected Industrial Sectors

    E-Print Network [OSTI]

    Worrell, Ernst; Price, Lynn; Neelis, Maarten; Galitsky, Christina; Zhou, Nan

    2007-01-01T23:59:59.000Z

    world best practice energy intensity values for productionWorld best practice energy intensity values for productionWorld Best Practice Final Energy Intensity Values for Aluminium Production (

  13. World Best Practice Energy Intensity Values for Selected Industrial Sectors

    E-Print Network [OSTI]

    Worrell, Ernst; Price, Lynn; Neelis, Maarten; Galitsky, Christina; Zhou, Nan

    2007-01-01T23:59:59.000Z

    Best Practice Final Energy Intensity Values for Stand-AloneBest Practice Final Energy Intensity Values for Stand-AloneBest Practice Primary Energy Intensity Values for Stand-

  14. Electrical discharge machining of titanium diboride and its composites

    E-Print Network [OSTI]

    Bedi, Harmohinder Singh

    1990-01-01T23:59:59.000Z

    ELECTRICAL DISCHARGE MACHINING OF TITANIUM DIBORIDE AND ITS COMPOSITES A Thesis by HARMOHINDER SINGH BEDI Submitted to the office of Graduate Studies of Texas ARM University in partial fulfillment of the requirements for the degree of MASTER... OF SCIENCE December 1990 Major Subject: Chemical Engineering ELECTRICAL DISCHARGE MACHINING OF TITANIUM DIBORIDE AND ITS COMPOSITES A THESIS by HARMOHINDER SINGH BEDI Approved as to style and content by: Ahmed M. Gadalla (Chair of Committee) Ralph...

  15. Discharge source with gas curtain for protecting optics from particles

    DOE Patents [OSTI]

    Fornaciari, Neal R.; Kanouff, Michael P.

    2004-03-30T23:59:59.000Z

    A gas curtain device is employed to deflect debris that is generated by an extreme ultraviolet and soft x-ray radiation discharge source such as an electric discharge plasma source. The gas curtain device projects a stream of gas over the path of the radiation to deflect debris particles into a direction that is different from that of the path of the radiation. The gas curtain can be employed to prevent debris accumulation on the optics used in photolithography.

  16. Spent nuclear fuel discharges from U.S. reactors 1994

    SciTech Connect (OSTI)

    NONE

    1996-02-01T23:59:59.000Z

    Spent Nuclear Fuel Discharges from US Reactors 1994 provides current statistical data on fuel assemblies irradiated at commercial nuclear reactors operating in the US. This year`s report provides data on the current inventories and storage capacities at these reactors. Detailed statistics on the data are presented in four chapters that highlight 1994 spent fuel discharges, storage capacities and inventories, canister and nonfuel component data, and assembly characteristics. Five appendices, a glossary, and bibliography are also included. 10 figs., 34 tabs.

  17. Fiber optic diagnostic techniques for the electrical discharge machining process

    E-Print Network [OSTI]

    Pillans, Brandon William

    2012-06-07T23:59:59.000Z

    FIBER OPTIC DIAGNOSTIC TECHNIQUES FOR THE ELECTRICAL DISCHARGE MACHINING PROCESS A Thesis by BRANDON WILLIAM PILLANS Submitted to the Office of Graduate Studies of Texas AB M University in partial fulfillment of the requirements... for the degree of MASTER OF SCIENCE August t 998 Major Subject: Electrical Engineering FIBER OPTIC DIAGNOSTIC TECHNIQUES FOR THE ELECTRICAL DISCHARGE MACHINING PROCESS A Thesis by BRANDON WILLIAM PILLANS Submitted to Texas A8M University in partial...

  18. A micrometer-size movable light emitting area in a resonant tunneling light emitting diode

    SciTech Connect (OSTI)

    Pettinari, G., E-mail: giorgio.pettinari@cnr.it [School of Physics and Astronomy, University of Nottingham, Nottingham NG7 2RD (United Kingdom); National Research Council (CNR), Institute for Photonics and Nanotechnologies (IFN-CNR), Via Cineto Romano 42, 00156 Roma (Italy); Balakrishnan, N.; Makarovsky, O.; Campion, R. P.; Patanè, A. [School of Physics and Astronomy, University of Nottingham, Nottingham NG7 2RD (United Kingdom)] [School of Physics and Astronomy, University of Nottingham, Nottingham NG7 2RD (United Kingdom); Polimeni, A.; Capizzi, M. [CNISM-Dipartimento di Fisica, Sapienza Università di Roma, P.le A. Moro 2, 00185 Roma (Italy)] [CNISM-Dipartimento di Fisica, Sapienza Università di Roma, P.le A. Moro 2, 00185 Roma (Italy)

    2013-12-09T23:59:59.000Z

    We report on the fabrication of a micrometer-size movable light emitting area in a GaAs/AlAs quantum well resonant tunneling p-i-n diode. The spatial position of the micrometer-size light emitting area shifts linearly with increasing applied bias, up to 30??m for a bias increment of 0.2?V. Also, the simultaneous resonant tunneling injection of both electrons and holes into the quantum well states is achieved at specific positions of the diode, thus resulting in a tenfold increase of the electroluminescence intensity.

  19. Interaction of a surface glow discharge with a gas flow

    SciTech Connect (OSTI)

    Aleksandrov, A. L., E-mail: a_alex@itam.nsc.ru; Schweigert, I. V. [Russian Academy of Sciences, Khristianovich Institute of Theoretical and Applied Mechanics, Siberian Branch (Russian Federation)

    2010-05-15T23:59:59.000Z

    A surface glow discharge in a gas flow is of particular interest as a possible tool for controlling the flow past hypersonic aircrafts. Using a hydrodynamic model of glow discharge, two-dimensional calculations for a kilovolt surface discharge in nitrogen at a pressure of 0.5 Torr are carried out in a stationary gas, as well as in a flow with a velocity of 1000 m/s. The discharge structure and plasma parameters are investigated near a charged electrode. It is shown that the electron energy in a cathode layer reaches 250-300 eV. Discharge is sustained by secondary electron emission. The influence of a high-speed gas flow on the discharge is considered. It is shown that the cathode layer configuration is flow-resistant. The distributions of the electric field and electron energy, as well as the ionization rate profile in the cathode layer, do not change qualitatively under the action of the flow. The basic effect of the flow's influence is a sharp decrease in the region of the quasineutral plasma surrounding the cathode layer due to fast convective transport of ions.

  20. State waste discharge permit application, 200-E chemical drain field

    SciTech Connect (OSTI)

    Not Available

    1994-06-01T23:59:59.000Z

    As part of the Hanford Federal Facility Agreement and Consent Order negotiations (Ecology et al. 1994), the US Department of Energy, Richland Operations Office, the US Environmental Protection Agency, and the Washington State Department of Ecology agreed that liquid effluent discharges to the ground on the Hanford Site which affect groundwater or have the potential to affect ground would be subject to permitting under the structure of Chapter 173-216 (or 173-218 where applicable) of the Washington Administrative Code, the State Waste Discharge Permit Program. As a result of this decision, the Washington State Department of Ecology and the US Department of Energy, Richland Operations Office entered into Consent Order No. DE 91NM-177, (Ecology and DOE-RL 1991). The Consent Order No. DE 91NM-177 requires a series of permitting activities for liquid effluent discharges. This document presents the State Waste Discharge Permit (SWDP) application for the 200-E Chemical Drain Field. Waste water from the 272-E Building enters the process sewer line directly through a floor drain, while waste water from the 2703-E Building is collected in two floor drains, (north and south) that act as sumps and are discharged periodically. The 272-E and 2703-E Buildings constitute the only discharges to the process sewer line and the 200-E Chemical Drain Field.

  1. Self-pulsing of hollow cathode discharge in various gases

    SciTech Connect (OSTI)

    Qin, Y.; He, F., E-mail: hefeng@bit.edu.cn; Jiang, X. X.; Ouyang, J. T., E-mail: jtouyang@bit.edu.cn [School of Physics, Beijing Institute of Technology, Beijing 100081 (China); Xie, K. [School of Aerospace Engineering, Beijing Institute of Technology, Beijing 100081 (China)

    2014-07-15T23:59:59.000Z

    In this paper, we investigate the self-pulsing phenomenon of cavity discharge in a cylindrical hollow cathode in various gases including argon, helium, nitrogen, oxygen, and air. The current-voltage characteristics of the cavity discharge, the waveforms of the self-pulsing current and voltage as well as the repetition frequency were measured. The results show that the pulsing frequency ranges from a few to tens kilohertz and depends on the averaged current and the pressure in all gases. The pulsing frequency will increase with the averaged current and decrease with the pressure. The rising time of the current pulse is nearly constant in a given gas or mixture. The self-pulsing does not depend on the external ballast but is affected significantly by the external capacitor in parallel with the discharge cell. The low-current self-pulsing in hollow cathode discharge is the mode transition between Townsend and glow discharges. It can be described by the charging-discharging process of an equivalent circuit consisting of capacitors and resistors.

  2. Arnold Schwarzenegger LIGHTING RESEARCH PROGRAM

    E-Print Network [OSTI]

    Project Summaries ELEMENT 2: ADVANCE LIGHTING TECHNOLOGIES PROJECT 2.1 LIGHT EMITTING DIODE (LED light emitting diodes (LED) technology for general lighting applications by developing a task lamp

  3. Diffuse Galactic Light in the Field of the Translucent High Galactic Latitude Cloud MBM32

    E-Print Network [OSTI]

    Ienaka, N; Matsuoka, Y; Sameshima, H; Oyabu, S; Tsujimoto, T; Peterson, B A

    2013-01-01T23:59:59.000Z

    We have conducted B, g, V, and R-band imaging in a 45x40 arcmin^2 field containing part of the high Galactic latitude translucent cloud MBM32, and correlated the intensity of diffuse optical light S_\

  4. New Light Sources for Tomorrow's Lighting Designs

    E-Print Network [OSTI]

    Krailo, D. A.

    , pioneered for headlam~for the automotive industry, has led to the development of halo en capsule lamps for general lighting. The original90-watt family PAR 38 lamps using tungsten halogen capsules produces the sa amount of useful light in the beam as a I... quartz PAR lamps with similar benefi . Each of these tungsten halogen capsule PAR wattages are av ilable in narrow spot, spot, and flood beam patterns. The most recent developments in the PAR halogen psule family include two entirely new lamp designs...

  5. LED Lighting Retrofit

    E-Print Network [OSTI]

    Shaw-Meadow, N.

    2011-01-01T23:59:59.000Z

    ? Municipal Street Lighting Consortium ? American Public Power Association (APPA) ? Demonstration in Energy Efficiency Development (DEED) ? Source of funding and database of completed LED roadway projects 6 Rules of the Road ESL-KT-11-11-57 CATEE 2011..., 2011 ? 9 Solar-Assisted LED Case Study LaQuinta Hotel, Cedar Park, Texas ? Utilizes 18 - ActiveLED Solar-Assisted Parking Lot Lights ? Utilizes ?power management? to extend battery life while handling light output ? Reduces load which reduces PV...

  6. High efficiency incandescent lighting

    DOE Patents [OSTI]

    Bermel, Peter; Ilic, Ognjen; Chan, Walker R.; Musabeyoglu, Ahmet; Cukierman, Aviv Ruben; Harradon, Michael Robert; Celanovic, Ivan; Soljacic, Marin

    2014-09-02T23:59:59.000Z

    Incandescent lighting structure. The structure includes a thermal emitter that can, but does not have to, include a first photonic crystal on its surface to tailor thermal emission coupled to, in a high-view-factor geometry, a second photonic filter selected to reflect infrared radiation back to the emitter while passing visible light. This structure is highly efficient as compared to standard incandescent light bulbs.

  7. High intensity performance of the Brookhaven AGS

    SciTech Connect (OSTI)

    Brennan, J.M.; Roser, T.

    1996-07-01T23:59:59.000Z

    Experience and results from recent high intensity proton running periods of the Brookhaven AGS, during which a record intensity for a proton synchrotron of 6.3 x 10{sup 13} protons/pulse was reached, is presented. This high beam intensity allowed for the simultaneous operation of three high precision rare kaon decay experiments. The record beam intensities were achieved after the 1.5 GeV Booster was commissioned and a transition jump system, a powerful transverse damper, and an rf upgrade in the AGS were completed. Recently even higher intensity proton synchrotrons are studied for neutron spallation sources or proton driver for a muon collider. Implications of the experiences from the AGS to these proposals and also possible future upgrades for the AGS are discussed.

  8. The solid state lighting initiative: An industry/DOE collaborativeeffort

    SciTech Connect (OSTI)

    Johnson, Steve

    2000-10-01T23:59:59.000Z

    A new era of technology is emerging in lighting. It is being propelled by the dramatic improvements in performance of solid state light sources. These sources offer an entirely new array of design aspects not achievable with current light sources. At the same time, their performance characteristics continue to improve and are expected to eclipse those of the most common light sources within the near future. High efficiency is one of these performance attributes motivating the Department of Energy (DOE) to work with the manufacturers of this new technology to create a program plan sufficiently comprehensive to support an industry-driven Solid State Lighting Initiative before Congress. The purpose of the initiative is to educate Congress about the potential of this technology to reduce the electric lighting load within the United States and, consequently, to realize the associated environmental benefits. The initiative will solicit congressional support to accelerate the development of solid state technology through investment in the research and development necessary to overcome the technical barriers that currently limit the products to niche markets. While there are multiple technologies being developed as solid state light sources, the two technologies which hold the most promise for application to general illumination are Light Emitting Diodes (LEDs) and Organic Light Emitting Diodes (OLEDs). The form of these sources can be quite different from current sources, allowing exciting new design uses for the products. Being diffuse sources, OLEDs are much lower in intensity per unit area than LEDs. The manufacturing process for OLEDs lends itself to shapes that can be formed to different geometries, making possible luminous panels or flexible luminous materials. Conversely, LEDs are very intense point sources which can be integrated into a small space to create an intense source or used separately for less focused applications. Both OLED and LED sources are expected to be thinner than other comparable sources; this thinness offers additional design opportunities.

  9. Total Light Management

    Broader source: Energy.gov [DOE]

    Presentation covers total light management, and is given at the Spring 2010 Federal Utility Partnership Working Group (FUPWG) meeting in Providence, Rhode Island.

  10. Lighting Technology Panel

    Broader source: Energy.gov [DOE]

    Presentation covers the Lighting Technology Panel for the Federal Utility Partnership Working Group (FUPWG) meeting, held on November 18-19, 2009. 

  11. Comparing Light Bulbs

    Broader source: Energy.gov [DOE]

    In this exercise, students will use a light to demonstrate the difference between being energy-efficient and energy-wasteful, and learn what energy efficiency means.

  12. Solid-State Lighting

    Broader source: Energy.gov (indexed) [DOE]

    research and design. Quality LED luminaires require program designed to successfully move solid-state lighting precise design of several components -LED arrays, electronic into the...

  13. Modeling Data-Intensive Web Sites 259 ModelingData-Intensive

    E-Print Network [OSTI]

    Bouras, Christos

    Modeling Data-Intensive Web Sites 259 ChapterXII ModelingData-Intensive Web Sites-by-stepapproachtothedesign,implementation and management of a Data-Intensive Web Site (DIWS). The approach introduces five data formulation is that of "Web fragments," that is an information decomposition technique that aids design, implementation

  14. OpenGL Lighting 13. OpenGL Lighting

    E-Print Network [OSTI]

    McDowell, Perry

    OpenGL Lighting 13. OpenGL Lighting · Overview of Lighting in OpenGL In order for lighting to have an effect in OpenGL, two things are required: A light An object to be lit Lights can be set to any color determine how they reflect the light which hits them. The color(s) of an object is determined

  15. Controlling X-rays With Light

    SciTech Connect (OSTI)

    Glover, Ernie; Hertlein, Marcus; Southworth, Steve; Allison, Tom; van Tilborg, Jeroen; Kanter, Elliot; Krassig, B.; Varma, H.; Rude, Bruce; Santra, Robin; Belkacem, Ali; Young, Linda

    2010-08-02T23:59:59.000Z

    Ultrafast x-ray science is an exciting frontier that promises the visualization of electronic, atomic and molecular dynamics on atomic time and length scales. A largelyunexplored area of ultrafast x-ray science is the use of light to control how x-rays interact with matter. In order to extend control concepts established for long wavelengthprobes to the x-ray regime, the optical control field must drive a coherent electronic response on a timescale comparable to femtosecond core-hole lifetimes. An intense field is required to achieve this rapid response. Here an intense optical control pulse isobserved to efficiently modulate photoelectric absorption for x-rays and to create an ultrafast transparency window. We demonstrate an application of x-ray transparencyrelevant to ultrafast x-ray sources: an all-photonic temporal cross-correlation measurement of a femtosecond x-ray pulse. The ability to control x-ray/matterinteractions with light will create new opportunities at current and next-generation x-ray light sources.

  16. Capillary - Discharge Based Hand-Held Detector For Chemical Vapor Monitoring

    DOE Patents [OSTI]

    Duan, Yixiang (White Rock, NM)

    2005-05-31T23:59:59.000Z

    A handheld/portable detector for chemical vapor monitoring includes a housing and a discharge chamber that is established therein. The plasma discharge has a relatively small volume, e.g., in the micro-liter range. A first electrode and a second electrode are disposed within the discharge chamber and a discharge gap is established therebetween. A sample gas tube is in fluid communication with the discharge chamber and provides a sample gas to the discharge chamber. Also, a plasma gas tube is in fluid communication with the discharge chamber and provides a plasma gas thereto. Accordingly, the plasma gas can be used to maintain microplasma discharge between the electrodes and the sample gas can be introduced into the microplasma discharge. A spectrometer optically connected to the handheld/portable detector is used to measure the radiation emitted by the sample gas when subjected to the microplasma discharge.

  17. Rules and Regulations Pertaining to a User Fee System for Point Source Dischargers that Discharge Pollutants into the Waters of the State (Rhode Island)

    Broader source: Energy.gov [DOE]

    These regulations establish a user fee system for point source dischargers that discharge pollutants into the surface waters of the State. The funds from such fees are used by the Department of...

  18. Impact Factors of Energy Intensity in China

    E-Print Network [OSTI]

    unknown authors

    Energy intensity reflects energy usage efficiency in the production and consumption process, and leads to carbon dioxide emissions and the energy security of an economy. Liao et al. (2007) analyzed factors contribute to the fluctuation of China’s energy intensity from 1997 to 2006, and found that efficiency effects and structural effects are the major impacting factors. Therefore, they suggested that China should attach more importance to optimizing its sectoral structure, and lowering its investment ratio in the future. However, economic development and energy intensity are influenced by many factors. In their research, Liao et al. (2007) omitted some important contributing factors to energy intensities, and their suggestions also had some practical limitations. First of all, Liao et al. (2007) did not analyze impacts from energy prices in energy usage efficiency. In the existing literature, Birol and Keppler (2000) applied economics theory and suggested that higher energy prices can induce the improvements in energy usage efficiency, thereby lowering energy intensity. Hang and Tu (2007) studied the influence of energy price on the Chinese economy's energy intensity and their empirical results also showed that higher energy prices can lower energy intensity. Because energy prices have been regulated by the

  19. Splayed mirror light pipes

    SciTech Connect (OSTI)

    Swift, P.D. [School of Physical Sciences, Dublin City University, Dublin 9 (Ireland)

    2010-02-15T23:59:59.000Z

    An expression is given for the transmission of the rectangular-section mirror light pipe. The expression is used to model throughputs for simulated solar conditions over a calender year. It is found that the splaying of a mirror light pipe results in a significant increase in throughputs particularly in winter months. (author)

  20. Reducing home lighting expenses

    SciTech Connect (OSTI)

    Aimone, M.A.

    1981-02-01T23:59:59.000Z

    Ways to reduce lighting expenses are summarized. These include: turning off lights when not in use; keeping fixtures and lamps clean; replacing lamps with more efficient types; using three-way bulbs; use of daylighting; buying fewer lamps and reducing lamp wattage; consider repainting rooms; replacing recessed fixtures with tracklighting; and using efficient lamps for outdoor use. (MCW)

  1. Temporal modulation of plasma species in atmospheric dielectric barrier discharges

    SciTech Connect (OSTI)

    Yang, Aijun; Wang, Xiaohua, E-mail: xhw@mail.xjtu.edu.cn, E-mail: mzrong@mail.xjtu.edu.cn; Liu, Dingxin; Rong, Mingzhe, E-mail: xhw@mail.xjtu.edu.cn, E-mail: mzrong@mail.xjtu.edu.cn [Centre for Plasma Biomedicine, State Key Laboratory of Electrical Insulation and Power Equipment, Xi'an Jiaotong University, Xi'an 710049 (China); Kong, Michael G. [Centre for Plasma Biomedicine, State Key Laboratory of Electrical Insulation and Power Equipment, Xi'an Jiaotong University, Xi'an 710049 (China); Frank Reidy Research Center for Bioelectrics, Department of Electrical and Computer Engineering, Old Dominion University, Virginia 23508 (United States); Department of Electrical and Computer Engineering, Old Dominion University, Norfolk, Virginia 23529 (United States)

    2014-07-15T23:59:59.000Z

    The atmospheric pressure dielectric barrier discharge in helium is a pulsed discharge in nature and the moment of maximum species densities is almost consistent with peak discharge current density. In this paper, a one-dimensional fluid model is used to investigate the temporal structure of plasma species in an atmospheric He-N{sub 2} dielectric barrier discharge (DBD). It is demonstrated that there exist microsecond delays of the moments of the maximum electron and ion densities from the peak of discharge current density. These time delays are caused by a competition between the electron impact and Penning ionizations, modulated by the N{sub 2} level in the plasma-forming gas. Besides, significant electron wall losses lead to the DBD being more positively charged and, with a distinct temporal separation in the peak electron and cation densities, the plasma is characterized with repetitive bursts of net positive charges. The temporal details of ionic and reactive plasma species may provide a new idea for some biological processes.

  2. Distribution, relative abundance and species composition of shrimp, crabs and fish in the intake area, discharge canal and cooling lake of the Cedar Bayou generating station, Baytown, Texas

    E-Print Network [OSTI]

    St. Clair, Lou Ann

    2012-06-07T23:59:59.000Z

    area and discharge waters of Houston Lighting S Power Company's Cedar Bayou Generating Station, Baytown, Texas. Hydrological data were taken at each sampling station. A total of 12 species of crustaceans and 53 species of fish was captured. The 10... juvenile stages risk entrainment through the plant (Mihursky and Kennedy 1967; Bascom 1974) or impingement on the intake screens. As Landry (1977) found, the impact of either entrainment or impingement depends mainly on the season of recruitment...

  3. Midlevel Ventilation's Constraint on Tropical Cyclone Intensity

    E-Print Network [OSTI]

    Tang, Brian Hong-An

    Midlevel ventilation, or the flux of low-entropy air into the inner core of a tropical cyclone (TC), is a hypothesized mechanism by which environmental vertical wind shear can constrain a tropical cyclone’s intensity. An ...

  4. Transport of elliptic intense charged -particle beams

    E-Print Network [OSTI]

    Zhou, J. (Jing), 1978-

    2006-01-01T23:59:59.000Z

    The transport theory of high-intensity elliptic charged-particle beams is presented. In particular, the halo formation and beam loss problem associated with the high space charge and small-aperture structure is addressed, ...

  5. Technical Change, Investment and Energy Intensity

    E-Print Network [OSTI]

    Kratena, Kurt

    This paper analyzes the role of different components of technical change on energy intensity by applying a Translog variable cost function setting to the new EU KLEMS dataset for 3 selected EU countries (Italy, Finland and ...

  6. Sustaining Performance Improvements in Energy Intensive Industries

    E-Print Network [OSTI]

    Moore, D. A.

    2005-01-01T23:59:59.000Z

    Experience has shown that significant opportunity for performance improvements exists in energy intensive operations. Often, efforts to improve efficiency focus on vendor-led initiatives to improve operations of particular equipment. This approach...

  7. Midlevel ventilation's constraint on tropical cyclone intensity

    E-Print Network [OSTI]

    Tang, Brian Hong-An

    2010-01-01T23:59:59.000Z

    Midlevel ventilation, or the flux of low-entropy air into the inner core of a tropical cyclone (TC), is a hypothesized mechanism by which environmental vertical wind shear can constrain a TC's intensity. An idealized ...

  8. Absolute vs. intensity-based emission caps

    E-Print Network [OSTI]

    Ellerman, A. Denny.

    Cap-and-trade systems limit emissions to some pre-specified absolute quantity. Intensity-based limits, that restrict emissions to some pre-specified rate relative to input or output, are much more widely used in environmental ...

  9. State Waste Discharge Permit application, 100-N Sewage Lagoon

    SciTech Connect (OSTI)

    Not Available

    1994-06-01T23:59:59.000Z

    As part of the Hanford Federal Facility Agreement and Consent Order negotiations (Ecology et al. 1994), the US Department of Energy, Richland Operations Office, the US Environmental Protection Agency, and the Washington State Department of Ecology agreed that liquid effluent discharges to the ground on the Hanford Site which affect groundwater or have the potential to affect groundwater would be subject to permitting under the structure of Chapter 173--216 (or 173--218 where applicable) of the Washington Administrative Code, the State Waste Discharge Permit Program. As a result of this decision, the Washington State Department of Ecology and the US Department of Energy, Richland Operations Office entered into Consent Order No. DE 91NM-177, (Ecology and DOE-RL 1991). This document constitutes the State Waste Discharge Permit application for the 100-N Sewage Lagoon. Since the influent to the sewer lagoon is domestic waste water, the State Waste Discharge Permit application for Public Owned Treatment Works Discharges to Land was used. Although the 100-N Sewage Lagoon is not a Public Owned Treatment Works, the Public Owned Treatment Works application is more applicable than the application for industrial waste water. The 100-N Sewage Lagoon serves the 100-N Area and other Hanford Site areas by receiving domestic waste from two sources. A network of sanitary sewer piping and lift stations transfers domestic waste water from the 100-N Area buildings directly to the 100-N Sewage Lagoon. Waste is also received by trucks that transport domestic waste pumped from on site septic tanks and holding tanks. Three ponds comprise the 100-N Sewage Lagoon treatment system. These include a lined aeration pond and stabilization pond, as well as an unlined infiltration pond. Both piped-in and trucked-in domestic waste is discharged directly into the aeration pond.

  10. Characteristics of electromagnetic interference generated during discharge of Mylar samples

    SciTech Connect (OSTI)

    Leung, P.L.

    1984-12-01T23:59:59.000Z

    This paper discusses the measurements of the electromagnetic interference (EMI) generated during discharges of Mylar samples. The two components of EMI, the conducted emission and the radiated emission, are characterized by the replacement current and the radiated RF spectrum respectively. The measured radiated RF spectra reveal important information on the source of the electromagnetic radiation. The possible sources are the replacement current pulse and the discharged generated plasma. The scaling of the amplitudes of the EMI, as a function of the area of the test sample, is also discussed.

  11. Electrostatic Discharge Sensitivity and Electrical Conductivity of Composite Energetic Materials

    SciTech Connect (OSTI)

    Michael A. Daniels; Daniel J. Prentice; Chelsea Weir; Michelle L. Pantoya; Gautham Ramachandran; Tim Dallas

    2013-02-01T23:59:59.000Z

    Composite energetic material response to electrical stimuli was investigated and a correlation between electrical conductivity and ignition sensitivity was examined. The composites consisted of micrometer particle aluminum combined with another metal, metal oxide, or fluoropolymer. Of the nine tested mixtures, aluminum with copper oxide was the only mixture to ignite by electrostatic discharge with minimum ignition energy (MIE) of 25 mJ and an electrical conductivity of 1246.25 nS; two orders of magnitude higher than the next composite. This study showed a similar trend in MIE for ignition triggered by a discharged spark compared with a thermal hot wire source.

  12. High-order harmonic generation in a capillary discharge

    DOE Patents [OSTI]

    Rocca, Jorge J.; Kapteyn, Henry C.; Mumane, Margaret M.; Gaudiosi, David; Grisham, Michael E.; Popmintchev, Tenio V.; Reagan, Brendan A.

    2010-06-01T23:59:59.000Z

    A pre-ionized medium created by a capillary discharge results in more efficient use of laser energy in high-order harmonic generation (HHG) from ions. It extends the cutoff photon energy, and reduces the distortion of the laser pulse as it propagates down the waveguide. The observed enhancements result from a combination of reduced ionization energy loss and reduced ionization-induced defocusing of the driving laser as well as waveguiding of the driving laser pulse. The discharge plasma also provides a means to spectrally tune the harmonics by tailoring the initial level of ionization of the medium.

  13. Simulating spin-charge separation with light

    E-Print Network [OSTI]

    Dimitris G. Angelakis; Mingxia Huo; Elica Kyoseva; Leong Chuan kwek

    2010-06-08T23:59:59.000Z

    In this work we show that stationary light-matter excitations generated inside a hollow one-dimensional waveguide filled with atoms, can be made to generate a photonic two-component Lieb Liniger model. We explain how to prepare and drive the atomic system to a strongly interacting regime where spin-charge separation could be possible. We then proceed by explaining how to measure the corresponding effective spin and charge densities and velocities through standard optical methods based in measuring dynamically the emitted photon intensities or by analyzing the photon spectrum. The relevant interactions exhibit the necessary tunability both to generate and efficiently observe spin charge separation with current technology.

  14. Green Light Pulse Oximeter

    DOE Patents [OSTI]

    Scharf, John Edward (Oldsmar, FL)

    1998-11-03T23:59:59.000Z

    A reflectance pulse oximeter that determines oxygen saturation of hemoglobin using two sources of electromagnetic radiation in the green optical region, which provides the maximum reflectance pulsation spectrum. The use of green light allows placement of an oximetry probe at central body sites (e.g., wrist, thigh, abdomen, forehead, scalp, and back). Preferably, the two green light sources alternately emit light at 560 nm and 577 nm, respectively, which gives the biggest difference in hemoglobin extinction coefficients between deoxyhemoglobin, RHb, and oxyhemoglobin, HbO.sub.2.

  15. White light velocity interferometer

    DOE Patents [OSTI]

    Erskine, David J. (Oakland, CA)

    1997-01-01T23:59:59.000Z

    The invention is a technique that allows the use of broadband and incoherent illumination. Although denoted white light velocimetry, this principle can be applied to any wave phenomenon. For the first time, powerful, compact or inexpensive sources can be used for remote target velocimetry. These include flash and arc lamps, light from detonations, pulsed lasers, chirped frequency lasers, and lasers operating simultaneously in several wavelengths. The technique is demonstrated with white light from an incandescent source to measure a target moving at 16 m/s.

  16. White light velocity interferometer

    DOE Patents [OSTI]

    Erskine, D.J.

    1997-06-24T23:59:59.000Z

    The invention is a technique that allows the use of broadband and incoherent illumination. Although denoted white light velocimetry, this principle can be applied to any wave phenomenon. For the first time, powerful, compact or inexpensive sources can be used for remote target velocimetry. These include flash and arc lamps, light from detonations, pulsed lasers, chirped frequency lasers, and lasers operating simultaneously in several wavelengths. The technique is demonstrated with white light from an incandescent source to measure a target moving at 16 m/s. 41 figs.

  17. White light velocity interferometer

    DOE Patents [OSTI]

    Erskine, David J. (Oakland, CA)

    1999-01-01T23:59:59.000Z

    The invention is a technique that allows the use of broadband and incoherent illumination. Although denoted white light velocimetry, this principle can be applied to any wave phenomenon. For the first time, powerful, compact or inexpensive sources can be used for remote target velocimetry. These include flash and arc lamps, light from detonations, pulsed lasers, chirped frequency lasers, and lasers operating simultaneously in several wavelengths. The technique is demonstrated with white light from an incandescent source to measure a target moving at 16 m/s.

  18. White light velocity interferometer

    DOE Patents [OSTI]

    Erskine, D.J.

    1999-06-08T23:59:59.000Z

    The invention is a technique that allows the use of broadband and incoherent illumination. Although denoted white light velocimetry, this principle can be applied to any wave phenomenon. For the first time, powerful, compact or inexpensive sources can be used for remote target velocimetry. These include flash and arc lamps, light from detonations, pulsed lasers, chirped frequency lasers, and lasers operating simultaneously in several wavelengths. The technique is demonstrated with white light from an incandescent source to measure a target moving at 16 m/s. 41 figs.

  19. Deflecting light into resonant cavities for spectroscopy

    DOE Patents [OSTI]

    Zare, Richard N. (Stanford, CA); Martin, Juergen (Harxheim, DE); Paldus, Barbara A. (Stanford, CA)

    1998-01-01T23:59:59.000Z

    Light is coupled into a cavity ring down spectroscopy (CRDS) resonant cavity using an acousto-optic modulator. The AOM allows in-coupling efficiencies in excess of 40%, which is two to three orders of magnitude higher than in conventional systems using a cavity mirror for in-coupling. The AOM shutoff time is shorter than the roundtrip time of the cavity. The higher light intensities lead to a reduction in shot noise, and allow the use of relatively insensitive but fast-responding detectors such as photovoltaic detectors. Other deflection devices such as electro-optic modulators or elements used in conventional Q-switching may be used instead of the AOM. The method is particularly useful in the mid-infrared, far-infrared, and ultraviolet wavelength ranges, for which moderately reflecting input mirrors are not widely available.

  20. Deflecting light into resonant cavities for spectroscopy

    DOE Patents [OSTI]

    Zare, R.N.; Martin, J.; Paldus, B.A.

    1998-09-29T23:59:59.000Z

    Light is coupled into a cavity ring down spectroscopy (CRDS) resonant cavity using an acousto-optic modulator. The AOM allows in-coupling efficiencies in excess of 40%, which is two to three orders of magnitude higher than in conventional systems using a cavity mirror for in-coupling. The AOM shutoff time is shorter than the roundtrip time of the cavity. The higher light intensities lead to a reduction in shot noise, and allow the use of relatively insensitive but fast-responding detectors such as photovoltaic detectors. Other deflection devices such as electro-optic modulators or elements used in conventional Q-switching may be used instead of the AOM. The method is particularly useful in the mid-infrared, far-infrared, and ultraviolet wavelength ranges, for which moderately reflecting input mirrors are not widely available. 5 figs.

  1. Light superconducting strings in the Galaxy

    E-Print Network [OSTI]

    Francesc Ferrer; Tanmay Vachaspati

    2006-08-08T23:59:59.000Z

    Observations of the Milky Way by the SPI/INTEGRAL satellite have confirmed the presence of a strong 511 KeV gamma-ray line emission from the bulge, which require an intense source of positrons in the galactic center. These observations are hard to account for by conventional astrophysical scenarios, whereas other proposals, such as light DM, face stringent constraints from the diffuse gamma-ray background. Here we suggest that light superconducting strings could be the source of the observed 511 KeV emission. The associated particle physics, at the ~ 1 TeV scale, is within reach of planned accelerator experiments, while the distinguishing spatial distribution, proportional to the galactic magnetic field, could be mapped by SPI or by future, more sensitive, satellite missions.

  2. Paraxial Light Beams with Angular Momentum

    E-Print Network [OSTI]

    A. Bekshaev; M. Soskin; M. Vasnetsov

    2008-01-15T23:59:59.000Z

    Fundamental and applied concepts concerning the ability of light beams to carry a certain mechanical angular momentum with respect to the propagation axis are reviewed and discussed. Following issues are included: Historical reference; Angular momentum of a paraxial beam and its constituents; Spin angular momentum and paradoxes associated with it; Orbital angular momentum; Circularly-spiral beams: examples and methods of generation; Orbital angular momentum and the intensity moments; Symmetry breakdown and decomposition of the orbital angular momentum; Mechanical models of the vortex light beams; Mechanical action of the beam angular momentum; Rotational Doppler effect, its manifestation in the image rotation; Spectrum of helical harmonics and associated problems; Non-collinear rotational Doppler effect; Properties of a beam forcedly rotating around its own axis. Research prospects and ways of practical utilization of optical beams with angular momentum.

  3. Lakeview Light and Power- Commercial Lighting Rebate Program

    Broader source: Energy.gov [DOE]

    Lakeview Light and Power offers a commercial lighting rebate program. Rebates apply to the installation of energy efficient lighting retrofits in non-residential buildings. The rebate program is...

  4. CW high intensity non-scaling FFAG proton drivers

    SciTech Connect (OSTI)

    Johnstone, C.; /Fermilab; Berz, M.; Makino, K.; /Michigan State U.; Snopok, P.; /IIT, Chicago

    2011-04-01T23:59:59.000Z

    Accelerators are playing increasingly important roles in basic science, technology, and medicine including nuclear power, industrial irradiation, material science, and neutrino production. Proton and light-ion accelerators in particular have many research, energy and medical applications, providing one of the most effective treatments for many types of cancer. Ultra high-intensity and high-energy (GeV) proton drivers are a critical technology for accelerator-driven sub-critical reactors (ADS) and many HEP programs (Muon Collider). These high-intensity GeV-range proton drivers are particularly challenging, encountering duty cycle and space-charge limits in the synchrotron and machine size concerns in the weaker-focusing cyclotrons; a 10-20 MW proton driver is not presently considered technically achievable with conventional re-circulating accelerators. One, as-yet, unexplored re-circulating accelerator, the Fixed-field Alternating Gradient, or FFAG, is an attractive alternative to the cyclotron. Its strong focusing optics are expected to mitigate space charge effects, and a recent innovation in design has coupled stable tunes with isochronous orbits, making the FFAG capable of fixed-frequency, CW acceleration, as in the classical cyclotron. This paper reports on these new advances in FFAG accelerator technology and references advanced modeling tools for fixed-field accelerators developed for and unique to the code COSY INFINITY.

  5. The interaction of intense subpicosecond laser pulses with underdense plasmas

    SciTech Connect (OSTI)

    Coverdale, C.A.

    1995-05-11T23:59:59.000Z

    Laser-plasma interactions have been of interest for many years not only from a basic physics standpoint, but also for their relevance to numerous applications. Advances in laser technology in recent years have resulted in compact laser systems capable of generating (psec), 10{sup 16} W/cm{sup 2} laser pulses. These lasers have provided a new regime in which to study laser-plasma interactions, a regime characterized by L{sub plasma} {ge} 2L{sub Rayleigh} > c{tau}. The goal of this dissertation is to experimentally characterize the interaction of a short pulse, high intensity laser with an underdense plasma (n{sub o} {le} 0.05n{sub cr}). Specifically, the parametric instability known as stimulated Raman scatter (SRS) is investigated to determine its behavior when driven by a short, intense laser pulse. Both the forward Raman scatter instability and backscattered Raman instability are studied. The coupled partial differential equations which describe the growth of SRS are reviewed and solved for typical experimental laser and plasma parameters. This solution shows the growth of the waves (electron plasma and scattered light) generated via stimulated Raman scatter. The dispersion relation is also derived and solved for experimentally accessible parameters. The solution of the dispersion relation is used to predict where (in k-space) and at what frequency (in {omega}-space) the instability will grow. Both the nonrelativistic and relativistic regimes of the instability are considered.

  6. Light Vector Mesons

    E-Print Network [OSTI]

    Alexander Milov

    2008-12-21T23:59:59.000Z

    This article reviews the current status of experimental results obtained in the measurement of light vector mesons produced in proton-proton and heavy ion collisions at different energies. The review is focused on two phenomena related to the light vector mesons; the modification of the spectral shape in search of Chiral symmetry restoration and suppression of the meson production in heavy ion collisions. The experimental results show that the spectral shape of light vector mesons are modified compared to the parameters measured in vacuum. The nature and the magnitude of the modification depends on the energy density of the media in which they are produced. The suppression patterns of light vector mesons are different from the measurements of other mesons and baryons. The mechanisms responsible for the suppression of the mesons are not yet understood. Systematic comparison of existing experimental results points to the missing data which may help to resolve the problem.

  7. Natural lighting and skylights

    E-Print Network [OSTI]

    Evans, Benjamin Hampton

    1961-01-01T23:59:59.000Z

    outlined herein, the feasibility of using scale models for studying skylights is also an established fact. The method of analysis by models can be a valuable tool to any designer who is concerned about day-lighting....

  8. Reading Municipal Light Department- Business Lighting Rebate Program

    Broader source: Energy.gov [DOE]

    Reading Municipal Light Department (RMLD) offers incentives for non-residential customers to install energy efficient lights and sensors in existing facilities. In addition to rebates for the...

  9. Types of Lighting in Commercial Buildings - Lighting Characteristics

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    of a light source's accuracy in rendering different colors when compared to a reference light source. The highest attainable CRI is 100. Lamps with CRIs above 70 are...

  10. Columbia Water and Light- HVAC and Lighting Efficiency Rebates

    Broader source: Energy.gov [DOE]

    Columbia Water and Light (CWL) offers rebates to its commercial and industrial customers for the purchase of high efficiency HVAC installations and efficient lighting. Incentives for certain...

  11. Induction Lighting: An Old Lighting Technology Made New Again...

    Broader source: Energy.gov (indexed) [DOE]

    around the same time that his rival, Thomas Edison, was working to improve the incandescent light bulb. In the early 1990s, several major lighting manufacturers introduced...

  12. Peninsula Light Company- Commercial Efficient Lighting Rebate Program

    Broader source: Energy.gov [DOE]

    Peninsula Light Company (PLC) offers a rebate program for commercial customers who wish to upgrade to energy efficient lighting. Participating customers must be served by PLC commercial service....

  13. High Hats, Swiss Cheese, and Fluorescent Lighting?

    SciTech Connect (OSTI)

    McCullough, Jeffrey J.; Gordon, Kelly L.

    2002-08-30T23:59:59.000Z

    For DOE, PNNL is conducting a competitive procurement to promote market introduction of new residential recessed downlights (also known as ''recessed cans'' or ''high hats'') that are airtight, rated for insulated ceilings, and hard-wired for CFLs. This paper discusses the potential energy savings of new high-efficiency downlights, and the results of product testing to date. Recessed downlights are the most popular residential lighting fixtures in the United States, with 21.7 million fixtures sold in 2000. An estimated 350 million are currently installed in American homes. Recessed cans are relatively inexpensive, and provide an unobtrusive, directed source of light for kitchens, hallways, and living rooms. Recessed cans are energy-intensive in three ways. First, virtually all recessed cans currently installed in the residential sector use incandescent light sources, typically reflector-type lamps drawing 65-150 watts. Second, heat from incandescent lamps adds to air-conditioning loads. Third, most installed recessed cans are not airtight, so they allow conditioned air to escape from the living area into unconditioned spaces such as attics. Addressing both lighting energy use and air leakage in recessed cans has proven challenging. Lighting energy efficiency is greatly improved by using CFLs. Air leakage can be addressed by making fixtures airtight. But when CFLs are used in an airtight recessed can, heat generated by the lamp and ballast is trapped within the fixture. Excessive heat causes reduced light output and shorter lifespan of the CFL. The procurement was designed to overcome these technical challenges and make new products available in the marketplace.

  14. ON COMPUTING UPPER LIMITS TO SOURCE INTENSITIES

    SciTech Connect (OSTI)

    Kashyap, Vinay L.; Siemiginowska, Aneta [Smithsonian Astrophysical Observatory, 60 Garden Street, Cambridge, MA 02138 (United States); Van Dyk, David A.; Xu Jin [Department of Statistics, University of California, Irvine, CA 92697-1250 (United States); Connors, Alanna [Eureka Scientific, 2452 Delmer Street, Suite 100, Oakland, CA 94602-3017 (United States); Freeman, Peter E. [Department of Statistics, Carnegie Mellon University, 5000 Forbes Avenue, Pittsburgh, PA 15213 (United States); Zezas, Andreas, E-mail: vkashyap@cfa.harvard.ed, E-mail: asiemiginowska@cfa.harvard.ed, E-mail: dvd@ics.uci.ed, E-mail: jinx@ics.uci.ed, E-mail: aconnors@eurekabayes.co, E-mail: pfreeman@cmu.ed, E-mail: azezas@cfa.harvard.ed [Physics Department, University of Crete, P.O. Box 2208, GR-710 03, Heraklion, Crete (Greece)

    2010-08-10T23:59:59.000Z

    A common problem in astrophysics is determining how bright a source could be and still not be detected in an observation. Despite the simplicity with which the problem can be stated, the solution involves complicated statistical issues that require careful analysis. In contrast to the more familiar confidence bound, this concept has never been formally analyzed, leading to a great variety of often ad hoc solutions. Here we formulate and describe the problem in a self-consistent manner. Detection significance is usually defined by the acceptable proportion of false positives (background fluctuations that are claimed as detections, or Type I error), and we invoke the complementary concept of false negatives (real sources that go undetected, or Type II error), based on the statistical power of a test, to compute an upper limit to the detectable source intensity. To determine the minimum intensity that a source must have for it to be detected, we first define a detection threshold and then compute the probabilities of detecting sources of various intensities at the given threshold. The intensity that corresponds to the specified Type II error probability defines that minimum intensity and is identified as the upper limit. Thus, an upper limit is a characteristic of the detection procedure rather than the strength of any particular source. It should not be confused with confidence intervals or other estimates of source intensity. This is particularly important given the large number of catalogs that are being generated from increasingly sensitive surveys. We discuss, with examples, the differences between these upper limits and confidence bounds. Both measures are useful quantities that should be reported in order to extract the most science from catalogs, though they answer different statistical questions: an upper bound describes an inference range on the source intensity, while an upper limit calibrates the detection process. We provide a recipe for computing upper limits that applies to all detection algorithms.

  15. Apparatus for injecting high power laser light into a fiber optic cable

    DOE Patents [OSTI]

    Sweatt, William C. (Albuquerque, NM)

    1997-01-01T23:59:59.000Z

    High intensity laser light is evenly injected into an optical fiber by the combination of a converging lens and a multisegment kinoform (binary optical element). The segments preferably have multi-order gratings on each which are aligned parallel to a radial line emanating from the center of the kinoform and pass through the center of the element. The grating in each segment causes circumferential (lateral) dispersion of the light, thereby avoiding detrimental concentration of light energy within the optical fiber.

  16. Paper area density measurement from forward transmitted scattered light

    DOE Patents [OSTI]

    Koo, Jackson C. (San Ramon, CA)

    2001-01-01T23:59:59.000Z

    A method whereby the average paper fiber area density (weight per unit area) can be directly calculated from the intensity of transmitted, scattered light at two different wavelengths, one being a non-absorpted wavelength. Also, the method makes it possible to derive the water percentage per fiber area density from a two-wavelength measurement. In the optical measuring technique optical transmitted intensity, for example, at 2.1 microns cellulose absorption line is measured and compared with another scattered, optical transmitted intensity reference in the nearby spectrum region, such as 1.68 microns, where there is no absorption. From the ratio of these two intensities, one can calculate the scattering absorption coefficient at 2.1 microns. This absorption coefficient at this wavelength is, then, experimentally correlated to the paper fiber area density. The water percentage per fiber area density can be derived from this two-wavelength measurement approach.

  17. Solid state lighting component

    DOE Patents [OSTI]

    Yuan, Thomas; Keller, Bernd; Ibbetson, James; Tarsa, Eric; Negley, Gerald

    2010-10-26T23:59:59.000Z

    An LED component comprising an array of LED chips mounted on a planar surface of a submount with the LED chips capable of emitting light in response to an electrical signal. The LED chips comprise respective groups emitting at different colors of light, with each of the groups interconnected in a series circuit. A lens is included over the LED chips. Other embodiments can comprise thermal spreading structures included integral to the submount and arranged to dissipate heat from the LED chips.

  18. Solid state lighting component

    DOE Patents [OSTI]

    Keller, Bernd; Ibbetson, James; Tarsa, Eric; Negley, Gerald; Yuan, Thomas

    2012-07-10T23:59:59.000Z

    An LED component comprising an array of LED chips mounted on a planar surface of a submount with the LED chips capable of emitting light in response to an electrical signal. The LED chips comprise respective groups emitting at different colors of light, with each of the groups interconnected in a series circuit. A lens is included over the LED chips. Other embodiments can comprise thermal spreading structures included integral to the submount and arranged to dissipate heat from the LED chips.

  19. Light and Energy -Daylight measurements

    E-Print Network [OSTI]

    Light and Energy - Daylight measurements #12;Light and Energy - Daylight measurements Authors: Jens;3 Title Light and Energy Subtitle Daylight measurements Authors Jens Christoffersen, Ásta Logadóttir ........................................................................................................ 5 Daylight quantity

  20. Energy Conservation in Industrial Lighting

    E-Print Network [OSTI]

    Meharg, E.

    1979-01-01T23:59:59.000Z

    In order to reduce energy use in lighting Union Carbide recently issued drastically reduced new lighting level standards. A computerized lighting cost program was also developed. Using this program a number of additional energy saving techniques...

  1. Lighting and the Bottom Line

    E-Print Network [OSTI]

    Christensen, M.

    1981-01-01T23:59:59.000Z

    A discussion of the cost of light and how it relates to the cost of people. The new Illuminating Engineering Society recommended method of determining lighting levels will be explained. Also several ways of providing good lighting to increase...

  2. Peculiarities of the Light Absorption and Emission by Free Electrons in Multivalley Semiconductors

    E-Print Network [OSTI]

    P. M. Tomchuk

    2008-11-18T23:59:59.000Z

    General expressions are obtained for the coefficient of light absorption by free carriers as well as the intensity of the spontaneous light emission by hot electrons in multivalley semiconductors. These expressions depend on the electron concentration and electron temperature in the individual valleys. An anisotropy of the dispersion law and electron scattering mechanisms is taken into account. Impurity-related and acoustic scattering mechanisms are analyzed. Polarization dependence of the spontaneous emission by hot electrons is found out. At unidirectional pressure applied or high irradiation intensities, the polarization dependence also appears in the coefficient of light absorption by free electrons.

  3. Radioactive Liquid Waste Treatment Facility Discharges in 2011

    SciTech Connect (OSTI)

    Del Signore, John C. [Los Alamos National Laboratory

    2012-05-16T23:59:59.000Z

    This report documents radioactive discharges from the TA50 Radioactive Liquid Waste Treatment Facilities (RLWTF) during calendar 2011. During 2011, three pathways were available for the discharge of treated water to the environment: discharge as water through NPDES Outfall 051 into Mortandad Canyon, evaporation via the TA50 cooling towers, and evaporation using the newly-installed natural-gas effluent evaporator at TA50. Only one of these pathways was used; all treated water (3,352,890 liters) was fed to the effluent evaporator. The quality of treated water was established by collecting a weekly grab sample of water being fed to the effluent evaporator. Forty weekly samples were collected; each was analyzed for gross alpha, gross beta, and tritium. Weekly samples were also composited at the end of each month. These flow-weighted composite samples were then analyzed for 37 radioisotopes: nine alpha-emitting isotopes, 27 beta emitters, and tritium. These monthly analyses were used to estimate the radioactive content of treated water fed to the effluent evaporator. Table 1 summarizes this information. The concentrations and quantities of radioactivity in Table 1 are for treated water fed to the evaporator. Amounts of radioactivity discharged to the environment through the evaporator stack were likely smaller since only entrained materials would exit via the evaporator stack.

  4. Corrosion mitigation considerations in planning for zero liquid discharge

    SciTech Connect (OSTI)

    DeWitt-Dick, D.B. [Ashland Chemical Co., Portland, TX (United States). Drew Industrial Division; Lee, B. [Ashland Chemical Co., Boonton, NJ (United States). Drew Industrial Division

    1995-12-01T23:59:59.000Z

    A reduction in the availability and in the quality of water, coupled with more significantly more stringent water discharge restrictions, has resulted in increasing numbers of industrial complexes investigating water reuse and zero liquid discharge. Their investigation generally includes a survey of the potential impact of increased dissolved solids on the formation of mineral salt scales on heat transfer surfaces. These predictive tools are readily available and fairly accurate. The prediction of corrosion potential, however, is not as clearly defined, and as a consequence, little consideration is given to the effects of increased solids on corrosion. In addition to the potential for accelerated corrosion related to increased dissolved solids, many reuse waters contain elevated levels of biological activity and are rich in the nutrients that feed these micro organisms. This paper looks at the reasons for selecting zero liquid discharge as a means of water conservation and discharge reduction, the unit operations available to achieve these goals, and the corrosion mechanisms and mitigation associated with reuse water.

  5. Aluminum-Enhanced Underwater Electrical Discharges for Steam Explosion Triggering

    SciTech Connect (OSTI)

    HOGELAND, STEVE R.; NELSON, LLOYD S.; ROTH, THOMAS CHRISTOPHER

    1999-07-01T23:59:59.000Z

    For a number of years, we have been initiating steam explosions of single drops of molten materials with pressure and flow (bubble growth) transients generated by discharging a capacitor bank through gold bridgewires placed underwater. Recent experimental and theoretical advances in the field of steam explosions, however, have made it important to substantially increase these relatively mild transients in water without using high explosives, if possible. To do this with the same capacitor bank, we have discharged similar energies through tiny strips of aluminum foil submerged in water. By replacing the gold wires with the aluminum strips, we were able to add the energy of the aluminum-water combustion to that normally deposited electrically by the bridgewire explosion in water. The chemical enhancement of the explosive characteristics of the discharges was substantial: when the same electrical energies were discharged through the aluminum strips, peak pressures increased as much as 12-fold and maximum bubble volumes as much as 5-fold above those generated with the gold wires. For given weights of aluminum, the magnitudes of both parameters appeared to exceed those produced by the underwater explosion of equivalent weights of high explosives.

  6. Wire-chamber radiation detector with discharge control

    DOE Patents [OSTI]

    Perez-Mendez, V.; Mulera, T.A.

    1982-03-29T23:59:59.000Z

    A wire chamber; radiation detector has spaced apart parallel electrodes and grids defining an ignition region in which charged particles or other ionizing radiations initiate brief localized avalanche discharges and defining an adjacent memory region in which sustained glow discharges are initiated by the primary discharges. Conductors of the grids at each side of the memory section extend in orthogonal directions enabling readout of the X-Y coordinates of locations at which charged particles were detected by sequentially transmitting pulses to the conductors of one grid while detecting transmissions of the pulses to the orthogonal conductors of the other grid through glow discharges. One of the grids bounding the memory region is defined by an array of conductive elements each of which is connected to the associated readout conductor through a separate resistance. The wire chamber avoids ambiguities and imprecisions in the readout of coordinates when large numbers of simultaneous or; near simultaneous charged particles have been detected. Down time between detection periods and the generation of radio frequency noise are also reduced.

  7. Condenser for extreme-UV lithography with discharge source

    SciTech Connect (OSTI)

    Sweatt, William C. (Albuquerque, NM); Kubiak, Glenn D. (Livermore, CA)

    2001-01-01T23:59:59.000Z

    Condenser system, for use with a ringfield camera in projection lithography, employs quasi grazing-incidence collector mirrors that are coated with a suitable reflective metal such as ruthenium to collect radiation from a discharge source to minimize the effect of contaminant accumulation on the collecting mirrors.

  8. Use of microalgae to remove pollutants from power plant discharges

    DOE Patents [OSTI]

    Wilde, E.W.; Benemann, J.R.; Weissman, J.C.; Tillett, D.M.

    1991-04-30T23:59:59.000Z

    A method and system are described for removing pollutants dissolved in the aqueous discharge of a plant, such as a power plant, from a body of water having known hydraulic and physicochemical characteristics, the method comprising (a) modifying the hydraulic system of the body of water including use of physical barriers to define a zone in a portion of the body of water which zone includes the discharge point and where the water has a range of physicochemical characteristics; (b) selecting a large and preferably filamentous, planktonically growing strain of algae adapted to absorb the particular pollutants and genetically dominating algae at the physicochemical characteristics of the zone; (c) establishing a colony of the selected algal strain in the zone; (d) harvesting a portion of the colony; and (e) reinoculating the zone near the discharge point with a fraction of the harvested portion. The fraction used for reinoculation can be adjusted to balance the rate of pollutant removal to the rate of pollutant discharge. 4 figures.

  9. Brookhaven National Laboratory State Pollutant Discharge Elimination System (SPDES)

    E-Print Network [OSTI]

    Homes, Christopher C.

    ;6 Alternate Disposal Options Hold & Haul · Collect waste in drums or tanks and ship offsite Small scale Influent: 100-200 ppt Clarifier: 5-45 ppt Discharge: 60- 120 ppt85% 15% Water table Under drain collection Groundwater: 2-9 ppt Sewage Treatment Plant Sand Filter Beds Rainwater: 5-9 ppt Aquifer #12;8 Factors

  10. COLLISIONLESS ELECTRON HEATING IN RF GAS DISCHARGES: I. QUASILINEAR THEORY

    E-Print Network [OSTI]

    Kaganovich, Igor

    COLLISIONLESS ELECTRON HEATING IN RF GAS DISCHARGES: I. QUASILINEAR THEORY Yu.M. Aliev1 , I an interest in mechanisms of electron heating and power deposition in the plasma main- tained by radio parameters. Due to the large value of the mean free path (MFP) the main mechanism of electron heating turns

  11. SYNAPTIC MECHANISMS Weber's law implies neural discharge more regular than

    E-Print Network [OSTI]

    Feng, Jianfeng

    SYNAPTIC MECHANISMS Weber's law implies neural discharge more regular than a Poisson process Jing, interspike interval, psychophysical law, spike rate Abstract Weber's law is one of the basic laws established. In this paper, we carried out an analysis on the spike train statistics when Weber's law holds

  12. High-speed micro-electro-discharge machining.

    SciTech Connect (OSTI)

    Chandrasekar, Srinivasan Dr. (.School of Industrial Engineering, West Lafayette, IN); Moylan, Shawn P. (School of Industrial Engineering, West Lafayette, IN); Benavides, Gilbert Lawrence

    2005-09-01T23:59:59.000Z

    When two electrodes are in close proximity in a dielectric liquid, application of a voltage pulse can produce a spark discharge between them, resulting in a small amount of material removal from both electrodes. Pulsed application of the voltage at discharge energies in the range of micro-Joules results in the continuous material removal process known as micro-electro-discharge machining (micro-EDM). Spark erosion by micro-EDM provides significant opportunities for producing small features and micro-components such as nozzle holes, slots, shafts and gears in virtually any conductive material. If the speed and precision of micro-EDM processes can be significantly enhanced, then they have the potential to be used for a wide variety of micro-machining applications including fabrication of microelectromechanical system (MEMS) components. Toward this end, a better understanding of the impacts the various machining parameters have on material removal has been established through a single discharge study of micro-EDM and a parametric study of small hole making by micro-EDM. The main avenues for improving the speed and efficiency of the micro-EDM process are in the areas of more controlled pulse generation in the power supply and more controlled positioning of the tool electrode during the machining process. Further investigation of the micro-EDM process in three dimensions leads to important design rules, specifically the smallest feature size attainable by the process.

  13. Estimating discharge in rivers using remotely sensed hydraulic information

    E-Print Network [OSTI]

    Smith, Laurence C.

    SAR images of three braided rivers were coupled with channel slope data obtained from topographic maps­100%) of the observed, with the mean estimate accuracy within 10%. This level of accuracy was achieved using calibration functions developed from observed discharge. The calibration functions use reach specific geomorphic

  14. ICE SHEET SOURCES OF SEA LEVEL RISE AND FRESHWATER DISCHARGE

    E-Print Network [OSTI]

    Carlson, Anders

    ICE SHEET SOURCES OF SEA LEVEL RISE AND FRESHWATER DISCHARGE DURING THE LAST DEGLACIATION Anders E the sources of sea level rise and freshwater dis- charge to the global oceans associated with retreat of ice­10 m sea level rise at 19.0­19.5 ka, sourced largely from Northern Hemisphere ice sheet retreat

  15. Treated wastewater discharged from municipal wastewater treatment plants (WWTPs) contains

    E-Print Network [OSTI]

    Fay, Noah

    Treated wastewater discharged from municipal wastewater treatment plants (WWTPs) contains to provide rapid, field-ready, inexpen- sive testing of these chemicals in wastewater is also needed estrogenic chemicals, and 2) develop sensor technology for the rapid measure- ment in wastewater of two key

  16. THE POSSIBILITY OF PRODUCING THERMONUCLEAR REACTIONS IN A GASEOUS DISCHARGE*

    E-Print Network [OSTI]

    THE POSSIBILITY OF PRODUCING THERMONUCLEAR REACTIONS IN A GASEOUS DISCHARGE* I.V. Kurchatov of the energy of thermonuclear reactions. Physicists the world over are attracted by the extraordinarily interest- ing and very difficult task of controlling thermonuclear reactiom. Investigations in this field

  17. Relationships Between Rate and Pattern of Unitary Discharges in Medial

    E-Print Network [OSTI]

    Weinberger, Norman M.

    Department of Psychobiology, School of Biological Sciences, University of California, Iwine, California 92664, a relatively brief sample of the single-unit record is often the basis for characterizing the stimulus-response charac- teristics of a unit. If unit discharge char- acteristics are invariant over time, a sample record

  18. Joint probability of precipitation and discharge deficits in the Netherlands

    E-Print Network [OSTI]

    Beersma, Jules

    Joint probability of precipitation and discharge deficits in the Netherlands Jules J. Beersma and T. Adri Buishand Royal Netherlands Meteorological Institute, De Bilt, The Netherlands Received 14 April] The Netherlands are situated at the downstream end of the Rhine River. A large part of the country can be supplied

  19. Growth and development of the tomato under high summer light intensities and high temperatures

    E-Print Network [OSTI]

    Johnson, Samuel Park

    1954-01-01T23:59:59.000Z

    of the tomato plant have been made by Kraus and Kraybill (20), Nightingale (28), Foster and Tatman (7) and 6 others. These workers found that low temperatures, low soil moisture, and low nitrogen favor accumulation of starch in the tomato plant. 7 A brief... April May June July Mig Sept Oct y*.1 jG11 G1 WlmmNHL Dc mDEAbsL ATmCTHNAlHTW OE iThHTTW yNbHTEbTOA NA aDssThT PANAODEg JTfNW1 FCCTH sOETW WbDu iOlHENs mNfOmlm ATmCTHNAlHTWg sDuTH sOETW AbT EDeAlHENs mOEOmlm ATmCTHNY AlHTW1 FCCTH iNWbTi sOET OEi...

  20. Optical coherence tomography based on intensity correlations of quasi-thermal light

    E-Print Network [OSTI]

    Zerom, Petros

    We show theoretically that the longitudinal resolution of conventional optical coherence tomography can be improved by a factor of radic2 when a two-photon (as opposed to a single-photon) sensitive detector is used, and ...

  1. A Light-weight Application Sharing Infrastructure for Graphics Intensive Applications

    E-Print Network [OSTI]

    Hao, M.C.; Lee, D.; Sventek, J.S.

    Hao,M.C. Lee,D. Sventek,J.S. Proceedings of the 5th International Symposium on High Performance Distributed Computing, Syracuse, NY, August 1996

  2. Fact #554: January 19, 2009 Energy Intensity of Light Rail Transit Systems

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-UpHeat PumpRecord ofESPCofConstructionofFY 2011 Report toAnnuAlFaces ofDecisions RM|

  3. Short-term Human Vision Protection from Intense Light Sources | Princeton

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administrationcontroller systemsBi (2)Sharing Smart GridShift End Shift End ASupplement:Plasma

  4. Light diffusing fiber optic chamber

    DOE Patents [OSTI]

    Maitland, Duncan J. (Lafayette, CA)

    2002-01-01T23:59:59.000Z

    A light diffusion system for transmitting light to a target area. The light is transmitted in a direction from a proximal end to a distal end by an optical fiber. A diffusing chamber is operatively connected to the optical fiber for transmitting the light from the proximal end to the distal end and transmitting said light to said target area. A plug is operatively connected to the diffusing chamber for increasing the light that is transmitted to the target area.

  5. July 18, 2012 Using QECBs for Street Lighting Upgrades

    E-Print Network [OSTI]

    lighting technologies (e.g. light-emitting diodes, induction lighting) can reduce street light energy

  6. Efficiency Maine Residential Lighting Program

    Broader source: Energy.gov [DOE]

    Efficiency Maine's Residential Lighting Program works directly with retailers and manufacturers to encourage residential customers to purchase energy-efficient lighting. Rebate amounts average $1...

  7. Radiation Reaction in High-Intense Fields

    E-Print Network [OSTI]

    Seto, Keita

    2015-01-01T23:59:59.000Z

    After the development of the radiating electron model by P. A. M. Dirac in 1938, many authors have tried to reformulate this model so-called radiation reaction. Recently, this effects has become important for ultra-intense laser-electron (plasma) interactions. In our recent research, we found a method for the stabilization of radiation reaction in quantum vacuum [PTEP 2014, 043A01 (2014), PTEP 2015, 023A01 (2015)]. In the other hand, the field modification by high-intense fields should be required under 10PW lasers, like ELI-NP facility. In this paper, I propose the combined method how to adopt the high-intense field correction with the stabilization by quantum vacuum as the extension from the model by Dirac.

  8. Future High-Intensity Proton Accelerators

    E-Print Network [OSTI]

    Gerigk, F

    2007-01-01T23:59:59.000Z

    This paper provides an overview of currently planned high-intensity proton accelerators. While for high energies (>10GeV) synchrotrons remain the preferred tools to produce high-intensity beams, recent years have seen an impressive development of linac-based lower-energy (intensity proton drivers for spallation sources, accelerator driven systems (ADS), production of Radioactive Ion Beams (RIB) and various neutrino applications (beta-beam, superbeam, neutrino factory). This paper discusses the optimum machine types for the various beam requirements and uses a range of projects, which are likely to be realised within the coming decade, to illustrate the different approaches to reach high average beam power with the application-specific time structure. Only machines with a beam power above 100kW are considered.

  9. Masking line foregrounds in intensity mapping surveys

    E-Print Network [OSTI]

    Breysse, Patrick C; Kamionkowski, Marc

    2015-01-01T23:59:59.000Z

    We address the problem of line confusion in intensity mapping surveys and explore the possibility to mitigate line foreground contamination by progressively masking the brightest pixels in the observed map. We consider experiments targeting CO(1-0) at $z=3$, Ly$\\alpha$ at $z=7$, and CII at $z=7$, and use simulated intensity maps, which include both clustering and shot noise components of the signal and possible foregrounds, in order to test the efficiency of our method. We find that for CO and Ly$\\alpha$ it is quite possible to remove most of the foreground contribution from the maps via only 1%-3% pixel masking. The CII maps will be more difficult to clean, however, due to instrumental constraints and the high-intensity foreground contamination involved. While the masking procedure sacrifices much of the astrophysical information present in our maps, we demonstrate that useful cosmological information in the targeted lines can be successfully retrieved.

  10. Narrowband inverse Compton scattering x-ray sources at high laser intensities

    E-Print Network [OSTI]

    Seipt, D; Surzhykov, A; Fritzsche, S

    2014-01-01T23:59:59.000Z

    Narrowband x- and gamma-ray sources based on the inverse Compton scattering of laser pulses suffer from a limitation of the allowed laser intensity due to the onset of nonlinear effects that increase their bandwidth. It has been suggested that laser pulses with a suitable frequency modulation could compensate this ponderomotive broadening and reduce the bandwidth of the spectral lines, which would allow to operate narrowband Compton sources in the high-intensity regime. In this paper we, therefore, present the theory of nonlinear Compton scattering in a frequency modulated intense laser pulse. We systematically derive the optimal frequency modulation of the laser pulse from the scattering matrix element of nonlinear Compton scattering, taking into account the electron spin and recoil. We show that, for some particular scattering angle, an optimized frequency modulation completely cancels the ponderomotive broadening for all harmonics of the backscattered light. We also explore how sensitive this compensation ...

  11. Short rise time intense electron beam generator

    DOE Patents [OSTI]

    Olson, C.L.

    1984-03-16T23:59:59.000Z

    A generator for producing an intense relativisitc electron beam having a subnanosecond current rise time includes a conventional generator of intense relativistic electrons feeding into a short electrically conductive drift tube including a cavity containing a working gas at a low enough pressure to prevent the input beam from significantly ionizing the working gas. Ionizing means such as a laser simultaneously ionize the entire volume of working gas in the cavity to generate an output beam having a rise time less than one nanosecond.

  12. Analysis of the Energy Intensity of Industries in California

    E-Print Network [OSTI]

    Can, Stephane de la Rue du

    2014-01-01T23:59:59.000Z

    the aggregate energy-intensity of industry. Applied Energyindustries with final energy intensities of 12.3 Billion BtuAs mentioned, the energy intensity of this sector is much

  13. ECE 466: LED Lighting Systems -Incandescent lightings rise and

    E-Print Network [OSTI]

    Schumacher, Russ

    versus cost - Power Electronic Drives for CFL and LED light sources to achieve dimmable operation - Basic electric AC and DC circuits at Sophomore level or equivalents Absolutes Lighting System Requirements index as a metric of a light source - Power Electronic Energy sources driving light sources in a compact

  14. Lighting and Surfaces 11.1 Introduction to Lighting

    E-Print Network [OSTI]

    Boyd, John P.

    -object-at-a-time. "Intrinsic" light is the light emitted by the object itself, such as the glow from a TV screen, a light-emitting diode, or a star. "Ambient" light is an illumination that seems to come from all sides. In the real

  15. Sandia National Laboratories: White Light Creation Architectures

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    TechnologiesWhite Light Creation Architectures White Light Creation Architectures Overview of SSL White Light Creation Architectures The entire spectral range of visible light can...

  16. Macroscopic behavior and discrete dynamo in high-[Theta] reversed-field pinch discharges

    SciTech Connect (OSTI)

    Arimoto, H.; Nakamura, A.; Sato, K.I.; Nagata, A.; Ando, T.; Kubota, S.; Masamune, S.; Nagatsu, M.; Tsukishima, T. (Plasma Science Center, Nagoya University, Chikusa-ku, Nagoya 464-01 (Japan))

    1993-06-01T23:59:59.000Z

    The magnetohydrodynamic (MHD) activity and the discrete dynamo in high-[Theta] reversed-field pinch (RFP) discharges are studied through comparisons with those in normal-[Theta] RFP discharges, where [Theta]=[ital B][sub [theta

  17. Utah Code Ann. § 19-5-107: Discharge of pollutants unlawful...

    Open Energy Info (EERE)

    Ann. 19-5-107: Discharge of pollutants unlawful -- Discharge permit required Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- StatuteStatute:...

  18. Microdischarge-assisted ignition of dielectric-barrier high-pressure glow discharges

    E-Print Network [OSTI]

    Raja, Laxminarayan L.

    in the ignition of high-pressure arc lamps8 and volume dc discharges.6 Here, we employ a hybrid discharge source of uniform, nonequilibrium glow plasmas for a variety of applications at pressures of 100

  19. airglow intensities measured: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Mark I 2013-01-01 23 Strongly Intensive Measures for Transverse Momentum and Particle Number Fluctuations Nuclear Experiment (arXiv) Summary: The strongly intensive measures ...

  20. 2014 call for NERSC's Data Intensive Computing Pilot Program...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NERSC's Data Intensive Computing Pilot Program 2014 call for NERSC's Data Intensive Computing Pilot Program Due December 10 November 18, 2013 by Francesca Verdier (0 Comments)...

  1. Reducing Industrial Energy Intensity in the Southeast Project...

    Broader source: Energy.gov (indexed) [DOE]

    Industrial Energy Intensity in the Southeast Project Fact Sheet Reducing Industrial Energy Intensity in the Southeast Project Fact Sheet This fact sheet contains details regarding...

  2. Quantitative Infrared Intensity Studies of Vapor-PhaseGlyoxal...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Infrared Intensity Studies of Vapor-Phase Glyoxal,Methylglyoxal, and 2,3-Butanedione (Diacetyl) with Quantitative Infrared Intensity Studies of Vapor-Phase Glyoxal,Methylglyoxal,...

  3. Absolute integrated intensities of vapor-phase hydrogen peroxide...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Absolute integrated intensities of vapor-phase hydrogen peroxide (H202) in the mid-infrared at atmospheric pressure. Absolute integrated intensities of vapor-phase hydrogen...

  4. EIA Energy Efficiency-Commercial Buildings Sector Energy Intensities...

    U.S. Energy Information Administration (EIA) Indexed Site

    Commercial Buildings Sector Energy Intensities Commercial Buildings Sector Energy Intensities: 1992- 2003 Released Date: December 2004 Page Last Revised: August 2009 These tables...

  5. Pupillary efficient lighting system

    DOE Patents [OSTI]

    Berman, Samuel M. (San Francisco, CA); Jewett, Don L. (Mill Valley, CA)

    1991-01-01T23:59:59.000Z

    A lighting system having at least two independent lighting subsystems each with a different ratio of scotopic illumination to photopic illumination. The radiant energy in the visible region of the spectrum of the lighting subsystems can be adjusted relative to each other so that the total scotopic illumination of the combined system and the total photopic illumination of the combined system can be varied independently. The dilation or contraction of the pupil of an eye is controlled by the level of scotopic illumination and because the scotopic and photopic illumination can be separately controlled, the system allows the pupil size to be varied independently of the level of photopic illumination. Hence, the vision process can be improved for a given level of photopic illumination.

  6. Light harvesting arrays

    DOE Patents [OSTI]

    Lindsey, Jonathan S. (Raleigh, NC)

    2002-01-01T23:59:59.000Z

    A light harvesting array useful for the manufacture of devices such as solar cells comprises: (a) a first substrate comprising a first electrode; and (b) a layer of light harvesting rods electrically coupled to the first electrode, each of the light harvesting rods comprising a polymer of Formula I: X.sup.1.paren open-st.X.sup.m+1).sub.m (I) wherein m is at least 1, and may be from two, three or four to 20 or more; X.sup.1 is a charge separation group (and preferably a porphyrinic macrocycle, which may be one ligand of a double-decker sandwich compound) having an excited-state of energy equal to or lower than that of X.sup.2, and X.sup.2 through X.sup.m+1 are chromophores (and again are preferably porphyrinic macrocycles).

  7. Light emitting ceramic device

    DOE Patents [OSTI]

    Valentine, Paul; Edwards, Doreen D.; Walker, Jr., William John; Slack, Lyle H.; Brown, Wayne Douglas; Osborne, Cathy; Norton, Michael; Begley, Richard

    2010-05-18T23:59:59.000Z

    A light-emitting ceramic based panel, hereafter termed "electroceramescent" panel, is herein claimed. The electroceramescent panel is formed on a substrate providing mechanical support as well as serving as the base electrode for the device. One or more semiconductive ceramic layers directly overlay the substrate, and electrical conductivity and ionic diffusion are controlled. Light emitting regions overlay the semiconductive ceramic layers, and said regions consist sequentially of a layer of a ceramic insulation layer and an electroluminescent layer, comprised of doped phosphors or the equivalent. One or more conductive top electrode layers having optically transmissive areas overlay the light emitting regions, and a multi-layered top barrier cover comprising one or more optically transmissive non-combustible insulation layers overlay said top electrode regions.

  8. Radioluminescent lighting technology

    SciTech Connect (OSTI)

    Not Available

    1990-01-01T23:59:59.000Z

    The glow-in-the-dark stereotype that characterizes the popular image of nuclear materials is not accidental. When the French scientist, Henri Becquerel, first discovered radioactivity in 1896, he was interested in luminescence. Radioluminescence, the production of light from a mixture of energetic and passive materials, is probably the oldest practical application of the unstable nucleus. Tritium-based radioluminescent lighting, in spite of the biologically favorable character of the gaseous tritium isotope, was included in the general tightening of environmental and safety regulations. Tritium light manufacturers would have to meet two fundamental conditions: (1) The benefit clearly outweighed the risk, to the extent that even the perceived risk of a skeptical public would be overcome. (2) The need was significant enough that the customer/user would be willing and able to afford the cost of regulation that was imposed both in the manufacture, use and eventual disposal of nuclear materials. In 1981, researchers at Oak Ridge National Laboratory were investigating larger radioluminescent applications using byproduct nuclear material such as krypton-85, as well as tritium. By 1982, it appeared that large source, (100 Curies or more) tritium gas tube, lights might be useful for marking runways and drop zones for military operations and perhaps even special civilian aviation applications. The successful development of this idea depended on making the light bright enough and demonstrating that large gas tube sources could be used and maintained safely in the environment. This successful DOE program is now in the process of being completed and closed-out. Working closely with the tritium light industry, State governments and other Federal agencies, the basic program goals have been achieved. This is a detailed report of what they have learned, proven, and discovered. 91 refs., 29 figs., 5 tabs. (JF)

  9. WHERE ARE THE MOST INTENSE THUNDERSTORMS

    E-Print Network [OSTI]

    Nesbitt, Steve

    provided unparalleled information on the global distribution of intense convective storms. T he Tropical-alti- tude, non-sun-synchronous orbit permits sampling throughout the diurnal cycle of precipitation. The cloud-top temperature of storms has been measured using infrared (IR) bright- ness temperature (Tb

  10. MANDATORY MEASURES INDOOR LIGHTING CONTROLS

    E-Print Network [OSTI]

    California at Davis, University of

    MANDATORY MEASURES INDOOR LIGHTING CONTROLS (Reference: Sub-Chapter 4, Section 130.1) #12;SECTION 4 MANDATORY LIGHTING CONTROLS 1. 130.1 (a) Area Controls: Manual controls that control lighting in each area separately 2. 130.1 (b) Multi-level Controls: Allow occupants to choose the appropriate light level for each

  11. MANDATORY MEASURES INDOOR LIGHTING CONTROLS

    E-Print Network [OSTI]

    California at Davis, University of

    MANDATORY MEASURES INDOOR LIGHTING CONTROLS (Reference: Sub-Chapter 4, Section 130.1) #12;SECTION 3 MANDATORY LIGHTING CONTROLS 1. 130.1 (a) Area Controls: Manual controls that control lighting in each area separately 2. 130.1 (b) Multi-level Controls: "Dimmability." Allow occupants to choose the appropriate light

  12. LIGHTING 101 1. Common terminology

    E-Print Network [OSTI]

    California at Davis, University of

    SECTION 3 LIGHTING 101 1. Common terminology 2. Sources & luminaires 3. Controls #12;SECTION 3SECTION 3 DISCUSSION: COMMON LIGHTING TERMINOLOGY 1. What are the definitions of the following lighting terms? 2. Do you use these terms in professional practice? 3. What other lighting terminology do you use

  13. MANDATORY MEASURES INDOOR LIGHTING CONTROLS

    E-Print Network [OSTI]

    California at Davis, University of

    MANDATORY MEASURES INDOOR LIGHTING CONTROLS (Reference: Sub-Chapter 4, Section 130.1) #12;SECTION 5 MANDATORY LIGHTING CONTROLS 1. Area Controls: Manual controls that control lighting in each area separately 2. Multi-level Controls: Allow occupants to choose the appropriate light level for each area 3. Shut

  14. LIGHTING 101 1. Common terminology

    E-Print Network [OSTI]

    California at Davis, University of

    LIGHTING 101 1. Common terminology 2. Sources and luminaires 3. Controls #12;SECTION 2 DISCUSSION: COMMON LIGHTING TERMINOLOGY 1. What are the definitions of the following lighting terms? 2. Do you use these terms in professional practice? 3. What other lighting terminology do you use on the job? SLIDE 14

  15. Extreme Ultraviolet Light Chris Cosio

    E-Print Network [OSTI]

    Hart, Gus

    Prospectus Extreme Ultraviolet Light Chris Cosio #12;The field of extreme ultraviolet light (XUV to the way XUV interacts with object, XUV properties are difficult to observe. Extreme ultraviolet light is absorbed by all objects it comes in contact with. Furthermore, extreme ultraviolet light also has low

  16. E-Print Network 3.0 - air vents discharge Sample Search Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1519 6.2. Compressed air energy storage... and discharge rates for many cycles. Indeed, the high cycling...

  17. E-Print Network 3.0 - abnormal glow discharge Sample Search Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Collection: Mathematics 24 Transition from Townsend to glow discharge: Subcritical, mixed, or supercritical characteristics Danijela D. Sijacic1 Summary: Transition...

  18. Lighting energy efficiency opportunities at Cheyenne Mountain Air Station

    SciTech Connect (OSTI)

    Molburg, J.C.; Rozo, A.J.; Sarles, J.K.; Haffenden, R.A.; Thimmapuram, P.R.; Cavallo, J.D.

    1996-06-01T23:59:59.000Z

    CMAS is an intensive user of electricity for lighting because of its size, lack of daylight, and 24-hour operating schedule. Argonne National Laboratory recently conducted a lighting energy conservation evaluation at CMAS. The evaluation included inspection and characterization of existing lighting systems, analysis of energy-efficient retrofit options, and investigation of the environmental effects that these lighting system retrofits could have when they are ready to be disposed of as waste. Argonne devised three retrofit options for the existing lighting systems at various buildings: (1) minimal retrofit--limited fixture replacement; (2) moderate retrofit--more extensive fixture replacement and limited application of motion detectors; and (3) advanced retrofit--fixture replacement, reduction in the number of lamps, expansion of task lighting, and more extensive application of motion detectors. Argonne used data on electricity consumption to analyze the economic and energy effects of these three retrofit options. It performed a cost analysis for each retrofit option in terms of payback. The analysis showed that lighting retrofits result in savings because they reduce electricity consumption, cooling load, and maintenance costs. The payback period for all retrofit options was found to be less than 2 years, with the payback period decreasing for more aggressive retrofits. These short payback periods derived largely from the intensive (24-hours-per-day) use of electric lighting at the facility. Maintenance savings accounted for more than half of the annual energy-related savings under the minimal and moderate retrofit options and slightly less than half of these savings under the advanced retrofit option. Even if maintenance savings were excluded, the payback periods would still be impressive: about 4.4 years for the minimal retrofit option and 2 years for the advanced option. The local and regional environmental impacts of the three retrofit options were minimal.

  19. The role of the gas/plasma plume and self-focusing in a gas-filled capillary discharge waveguide for high-power laser-plasma applications

    SciTech Connect (OSTI)

    Ciocarlan, C. [Department of Physics, Scottish Universities Physics Alliance, University of Strathclyde, Glasgow G4 0NG (United Kingdom) [Department of Physics, Scottish Universities Physics Alliance, University of Strathclyde, Glasgow G4 0NG (United Kingdom); Department of Nuclear Physics, Horia Hulubei National Institute of Physics and Nuclear Engineering, 76900 Bucharest-Magurele (Romania); Wiggins, S. M.; Islam, M. R.; Ersfeld, B.; Abuazoum, S.; Wilson, R.; Aniculaesei, C.; Welsh, G. H.; Vieux, G.; Jaroszynski, D. A. [Department of Physics, Scottish Universities Physics Alliance, University of Strathclyde, Glasgow G4 0NG (United Kingdom)] [Department of Physics, Scottish Universities Physics Alliance, University of Strathclyde, Glasgow G4 0NG (United Kingdom)

    2013-09-15T23:59:59.000Z

    The role of the gas/plasma plume at the entrance of a gas-filled capillary discharge plasma waveguide in increasing the laser intensity has been investigated. Distinction is made between neutral gas and hot plasma plumes that, respectively, develop before and after discharge breakdown. Time-averaged measurements show that the on-axis plasma density of a fully expanded plasma plume over this region is similar to that inside the waveguide. Above the critical power, relativistic and ponderomotive self-focusing lead to an increase in the intensity, which can be nearly a factor of 2 compared with the case without a plume. When used as a laser plasma wakefield accelerator, the enhancement of intensity can lead to prompt electron injection very close to the entrance of the waveguide. Self-focusing occurs within two Rayleigh lengths of the waveguide entrance plane in the region, where the laser beam is converging. Analytical theory and numerical simulations show that, for a density of 3.0 × 10{sup 18} cm{sup ?3}, the peak normalized laser vector potential, a{sub 0}, increases from 1.0 to 1.85 close to the entrance plane of the capillary compared with a{sub 0} = 1.41 when the plume is neglected.

  20. Experimental Effects of Atomic Oxygen on the Development of an Electric Discharge Oxygen Iodine Laser

    E-Print Network [OSTI]

    Carroll, David L.

    state I. Conventionally, a two-phase (gas-liquid) chemistry singlet oxygen generator (SOG) producesExperimental Effects of Atomic Oxygen on the Development of an Electric Discharge Oxygen Iodine of the electric discharge iodine laser continues, the role of oxygen atoms downstream of the discharge region

  1. Transition from Townsend to glow discharge: Subcritical, mixed, or supercritical characteristics Danijela D. Sijacic1

    E-Print Network [OSTI]

    Ebert, Ute

    Transition from Townsend to glow discharge: Subcritical, mixed, or supercritical characteristics, the transition from Townsend to glow discharge can show the textbook subcritical behavior, but for smaller values long discharges that have a clearly pronounced subcritical characteristics, i.e., for fixed large pd

  2. DOE Technical Assistance Program

    Broader source: Energy.gov (indexed) [DOE]

    Steward, LC Pacific Northwest National Laboratory Research Engineer 8 | TAP Webinar eere.energy.gov * High-Intensity Discharge Lamps - Dominant source in outdoor lighting -...

  3. Lead acid battery pulse discharge investigation. Final report

    SciTech Connect (OSTI)

    Dowgiallo, E

    1980-04-01T23:59:59.000Z

    The effects of high current pulses caused by electric vehicle silicon-controlled rectifier and transistor chopper controllers on battery energy, lifetime, and microstructure were studied. Test equipment and results are described. It was found that the energy of improved golf cart-type batteries deteriorated under pulsed conditions by about 10% with respect to dc conditions for pulses between 16 and 333 Hz - no difference was noted above 333 Hz. Frequencies and duty cycles characteristic of electric vehicle controllers produce ampere-hour capacities similar in magnitude to dc discharges of the same average currents. The amount of positive plate corrosion under pulsed conditions was about twice that ot the unpulsed. Unusually large lead sulfate crystals were found in isolated colonies in pulsed plates, whereas a battery that had been discharged each cycle at an equivalent steady state did not show these large crystals. 5 figures, 3 tables. (RWR)

  4. Optogalvanic effect in a hollow cathode discharge with nonlaser sources

    SciTech Connect (OSTI)

    Apel, C.T.; Keller, R.A.; Zalewski, E.F.; Engleman, R. Jr.

    1982-04-15T23:59:59.000Z

    Several atomic emission sources were investigated for their potential to induce optogalvanic signals in hollow cathode lamps. The sources included an inductively coupled argon plasma, a H/sub 2/--O/sub 2/ flame, a high-temperature furnace, electrodeless microwave discharge lamps, and hollow cathode lamps. Successful results were obtained with argon emission from the inductively coupled plasma focused into an argon-filled hollow cathode tube and with atomic emission from one hollow cathode discharge focused into a hollow cathode tube containing the same element. Very low level optogalvanic signals were observed from the other sources but could not be unambiguously ascribed to emission from a specific element. A problem encountered was the presence of a background signal due to photoelectric emission and possibly radiative heating of the cathode.

  5. Temporal process of plasma discharge by an electron beam

    SciTech Connect (OSTI)

    Sugawa, M.; Sugaya, R.; Isobe, S.; Kumar, A. [Department of Physics, Faculty of Science, Ehime University, Matsuyama 790 (Japan); Honda, H. [Institute of Laser Engineering, Osaka University, Suita, Osaka 565 (Japan)

    1996-05-01T23:59:59.000Z

    The process of the plasma discharge due to an electron beam is experimentally investigated. A pulse ({approximately}540 {mu}s) of an electron beam (0.5{endash}1.5 keV, {le}20 mA) is injected into argon gas (5{times}10{sup {minus}5}{endash}5{times}10{sup {minus}4} Torr) in a magnetic field (50{endash}300 G). The discharge based on a gas break down occurs cascade-likely in time. The gas beak down with some steps is explained by the two stream instability of an electron beam-plasma system, from the observation of the temporal evolution of the frequency spectra (0{endash}3.0 GHz) of the instability and the measurement of the temporal plasma density and temperature. {copyright} {ital 1996 American Institute of Physics.}

  6. Redox reactions with empirical potentials: Atomistic battery discharge simulations

    E-Print Network [OSTI]

    Dapp, Wolf B

    2013-01-01T23:59:59.000Z

    Batteries are pivotal components in overcoming some of today's greatest technological challenges. Yet to date there is no self-consistent atomistic description of a complete battery. We take first steps toward modeling of a battery as a whole microscopically. Our focus lies on phenomena occurring at the electrode-electrolyte interface which are not easily studied with other methods. We use the redox split-charge equilibration (redoxSQE) method that assigns a discrete ionization state to each atom. Along with exchanging partial charges across bonds, atoms can swap integer charges. With redoxSQE we study the discharge behavior of a nano-battery, and demonstrate that this reproduces the generic properties of a macroscopic battery qualitatively. Examples are the dependence of the battery's capacity on temperature and discharge rate, as well as performance degradation upon recharge.

  7. Equilibrium analysis of tokamak discharges with toroidal variation

    SciTech Connect (OSTI)

    Zwingmann, W.; Becoulet, M.; Moreau, Ph.; Nardon, E. [Ass Euratom-CEA/DSM/DRFC Cadarache, 13108 St.-Paul-Lez-Durance (France)

    2006-11-30T23:59:59.000Z

    Tokamaks provide a field structure that is almost axisymmetric around the torus axis. There are however always small toroidal variations due to the limited number of toroidal field coils, the magnetic field ripple. On the other hand, non-axisymmetric external fields are applied on purpose to ergodise the field structure close to the separatrix, to control the heat and particle transport across the plasma boundary. We present a perturbation method to calculate the magnetic field of tokamak discharges with with weak toroidal variation. The method is applied for the equilibrium reconstruction of Tore Supra discharges with toroidal ripple. The perturbation method does not rely on a flux surface representation and can therefore be applied to structures with magnetic islands. We obtain the plasma response to the field of ergodising external coils, as proposed for the ITER device.

  8. Machinability of a Stainless Steel by Electrochemical Discharge Microdrilling

    SciTech Connect (OSTI)

    Coteata, Margareta; Pop, Nicolae; Slatineanu, Laurentiu ['Gheorghe Asachi' Technical University of Iasi, Department of Machine Manufacturing Technology, Blvd. D Mangeron 59A, 700050 Iasi (Romania); Schulze, Hans-Peter [Otto-von-Guericke-University Magdeburg, Institute of Fundamental Electrical Engineering and EMC Universitaetsplatz 2, D-39106 Magdeburg (Germany); Besliu, Irina [University 'Stefan cel Mare' of Suceava, Department of Technologies and Management, Str. Universitatii, 13, 720 229 Suceava (Romania)

    2011-05-04T23:59:59.000Z

    Due to the chemical elements included in their structure for ensuring an increased resistance to the environment action, the stainless steels are characterized by a low machinability when classical machining methods are applied. For this reason, sometimes non-traditional machining methods are applied, one of these being the electrochemical discharge machining. To obtain microholes and to evaluate the machinability by electrochemical discharge microdrilling, test pieces of stainless steel were used for experimental research. The electrolyte was an aqueous solution of sodium silicate with different densities. A complete factorial plan was designed to highlight the influence of some input variables on the sizes of the considered machinability indexes (electrode tool wear, material removal rate, depth of the machined hole). By mathematically processing of experimental data, empirical functions were established both for stainless steel and carbon steel. Graphical representations were used to obtain more suggestive vision concerning the influence exerted by the considered input variables on the size of the machinability indexes.

  9. Depth Profile Analysis of New Materials in Hollow Cathode Discharge

    SciTech Connect (OSTI)

    Djulgerova, R.; Mihailov, V.; Gencheva, V.; Popova, L.; Panchev, B. [Institute of Solid State Physics - Bulgarian Academy of Sciences, 1784 Sofia (Bulgaria); Michaylova, V. [Technical University of Sofia, 1797 Sofia (Bulgaria); Szytula, A.; Gondek, L.; Dohnalik, T.M. [Smoluchowski Institute of Physics - Jagellonian University, 30-059 Cracow (Poland); Petrovic, Z.Lj. [Institute of Physics, 11080 Zemun, Belgrade (Serbia and Montenegro)

    2004-12-01T23:59:59.000Z

    In this review the possibility of hollow cathode discharge for depth profile analysis is demonstrated for several new materials: planar optical waveguides fabricated by Ag+-Na+ ion exchange process in glasses, SnO2 thin films for gas sensors modified by hexamethildisilazane after rapid thermal annealing, W- and WC- CVD layers deposited on Co-metalloceramics and WO3- CVD thin films deposited on glass. The results are compared with different standard techniques.

  10. Method and apparatus for processing exhaust gas with corona discharge

    DOE Patents [OSTI]

    Barlow, S.E.; Orlando, T.M.; Tonkyn, R.G.

    1999-06-22T23:59:59.000Z

    The present invention is placing a catalyst coating upon surfaces surrounding a volume containing corona discharge. In addition, the electrodes are coated with a robust dielectric material. Further, the electrodes are arranged so that at least a surface portion of each electrode extends into a flow path of the exhaust gas to be treated and there is only exhaust gas in the volume between each pair of electrodes. 12 figs.

  11. High energy XeBr electric discharge laser

    DOE Patents [OSTI]

    Sze, Robert C. (Santa Fe, NM); Scott, Peter B. (Los Alamos, NM)

    1981-01-01T23:59:59.000Z

    A high energy XeBr laser for producing coherent radiation at 282 nm. The XeBr laser utilizes an electric discharge as the excitation source to minimize formation of molecular ions thereby minimizing absorption of laser radiation by the active medium. Additionally, HBr is used as the halogen donor which undergoes harpooning reactions with Xe.sub.M * to form XeBr*.

  12. High energy KrCl electric discharge laser

    DOE Patents [OSTI]

    Sze, Robert C. (Santa Fe, NM); Scott, Peter B. (Los Alamos, NM)

    1981-01-01T23:59:59.000Z

    A high energy KrCl laser for producing coherent radiation at 222 nm. Output energies on the order of 100 mJ per pulse are produced utilizing a discharge excitation source to minimize formation of molecular ions, thereby minimizing absorption of laser radiation by the active medium. Additionally, HCl is used as a halogen donor which undergoes a harpooning reaction with metastable Kr.sub.M * to form KrCl.

  13. Negative ion source with hollow cathode discharge plasma

    DOE Patents [OSTI]

    Hershcovitch, A.; Prelec, K.

    1980-12-12T23:59:59.000Z

    A negative ion source of the type where negative ions are formed by bombarding a low-work-function surface with positive ions and neutral particles from a plasma, wherein a highly ionized plasma is injected into an anode space containing the low-work-function surface is described. The plasma is formed by hollow cathode discharge and injected into the anode space along the magnetic field lines. Preferably, the negative ion source is of the magnetron type.

  14. The Use of DC Glow Discharges as Undergraduate Educational Tools

    SciTech Connect (OSTI)

    Stephanie A. Wissel and Andrew Zwicker, Jerry Ross, and Sophia Gershman

    2012-10-09T23:59:59.000Z

    Plasmas have a beguiling way of getting students excited and interested in physics. We argue that plasmas can and should be incorporated into the undergraduate curriculum as both demonstrations and advanced investigations of electromagnetism and quantum effects. Our device, based on a direct current (DC) glow discharge tube, allows for a number of experiments into topics such as electrical breakdown, spectroscopy, magnetism, and electron temperature.

  15. Windows and lighting program

    SciTech Connect (OSTI)

    Not Available

    1990-06-01T23:59:59.000Z

    More than 30% of all energy use in buildings is attributable to two sources: windows and lighting. Together they account for annual consumer energy expenditures of more than $50 billion. Each affects not only energy use by other major building systems, but also comfort and productivity -- factors that influence building economics far more than does direct energy consumption alone. Windows play a unique role in the building envelope, physically separating the conditioned space from the world outside without sacrificing vital visual contact. Throughout the indoor environment, lighting systems facilitate a variety of tasks associated with a wide range of visual requirements while defining the luminous qualities of the indoor environment. Windows and lighting are thus essential components of any comprehensive building science program. Despite important achievements in reducing building energy consumption over the past decade, significant additional savings are still possible. These will come from two complementary strategies: (1) improve building designs so that they effectively apply existing technologies and extend the market penetration of these technologies; and (2) develop advanced technologies that increase the savings potential of each application. Both the Windows and Daylighting Group and the Lighting System Research Group have made substantial contributions in each of these areas, and continue to do so through the ongoing research summarized here. 23 refs., 16 figs.

  16. Radioluminescent polymer lights

    SciTech Connect (OSTI)

    Jensen, G.A.; Nelson, D.A.; Molton, P.M.

    1990-09-01T23:59:59.000Z

    The preparation of radioluminescent light sources where the tritium is located on the aryl-ring in a polymer has been demonstrated with deuterium/tritium substitution. This report discusses tests, results, and future applications of radioluminescent polymers. 10 refs. (FI)

  17. Sweetness and light 

    E-Print Network [OSTI]

    Craig, Katie

    2014-07-03T23:59:59.000Z

    1. Sweetness and Light. A novel. Judi lives in a nice, clean house with her seventeen year old stepson, who won’t talk to her in anything but monosyllables. His father, Nelson, and she are struggling to relate to each ...

  18. Reactor-specific spent fuel discharge projections: 1985 to 2020

    SciTech Connect (OSTI)

    Heeb, C.M.; Libby, R.A.; Walling, R.C.; Purcell, W.L.

    1986-09-01T23:59:59.000Z

    The creation of four spent-fuel data bases that contain information on the projected amounts of spent fuel to be discharged from US commercial nuclear reactors through the year 2020 is described. The data bases contain detailed spent-fuel information from existing, planned, and projected pressurized water reactors (PWR) and boiling water reactors (BWR). The projections are based on individual reactor information supplied by the US reactor owners. The basic information is adjusted to conform to Energy Information Agency (EIA) forecasts for nuclear installed capacity, generation, and spent fuel discharged. The EIA cases considered are: (1) No New Orders with Extended Burnup, (2) No New Orders with Constant Burnup, (3) Middle Case with Extended Burnup, and (4) Middle Case with Constant Burnup. Detailed, by-reactor tables are provided for annual discharged amounts of spent fuel, for storage requirements assuming maximum-at-reactor storage, and for storage requirements assuming maximum-at-reactor plus intra-utility transshipment of spent fuel.

  19. Ignition and extinction phenomena in helium micro hollow cathode discharges

    SciTech Connect (OSTI)

    Kulsreshath, M. K.; Schwaederle, L.; Dufour, T.; Lefaucheux, P.; Dussart, R. [GREMI, CNRS/Université d'Orléans (UMR7344), Orléans (France); Sadeghi, N. [LIPhy, CNRS and Universite Joseph Fourier (UMR5588), Grenoble (France); Overzet, L. J. [GREMI, CNRS/Université d'Orléans (UMR7344), Orléans (France); PSAL, UTDallas, Richardson, Texas 75080-3021 (United States)

    2013-12-28T23:59:59.000Z

    Micro hollow cathode discharges (MHCD) were produced using 250??m thick dielectric layer of alumina sandwiched between two nickel electrodes of 8??m thickness. A through cavity at the center of the chip was formed by laser drilling technique. MHCD with a diameter of few hundreds of micrometers allowed us to generate direct current discharges in helium at up to atmospheric pressure. A slowly varying ramped voltage generator was used to study the ignition and the extinction periods of the microdischarges. The analysis was performed by using electrical characterisation of the V-I behaviour and the measurement of He*({sup 3}S{sub 1}) metastable atoms density by tunable diode laser spectroscopy. At the ignition of the microdischarges, 2??s long current peak as high as 24?mA was observed, sometimes followed by low amplitude damped oscillations. At helium pressure above 400?Torr, an oscillatory behaviour of the discharge current was observed just before the extinction of the microdischarges. The same type of instability in the extinction period at high pressure also appeared on the density of He*({sup 3}S{sub 1}) metastable atoms, but delayed by a few ?s relative to the current oscillations. Metastable atoms thus cannot be at the origin of the generation of the observed instabilities.

  20. Reactor-specific spent fuel discharge projections, 1987-2020

    SciTech Connect (OSTI)

    Walling, R.C.; Heeb, C.M.; Purcell, W.L.

    1988-03-01T23:59:59.000Z

    The creation of five reactor-specific spent fuel data bases that contain information on the projected amounts of spent fuel to be discharged from U.S. commercial nuclear reactors through the year 2020 is described. The data bases contain detailed spent fuel information from existing, planned, and projected pressurized water reactors (PWR) and boiling water eactors (BWR), and one existing high temperature gas reactor (HTGR). The projections are based on individual reactor information supplied by the U.S. reactor owners. The basic information is adjusted to conform to Energy Information Administration (EIA) forecasts for nuclear installed capacity, generation, and spent fuel discharged. The EIA cases considered are: No New Orders (assumes increasing burnup), No New Orders with No Increased Burnup, Upper Reference (assumes increasing burnup), Upper Reference with No Increased Burnup, and Lower Reference (assumes increasing burnup). Detailed, by-reactor tables are provided for annual discharged amounts of spent fuel, for storage requirements assuming maximum at-reactor storage, and for storage requirements assuming maximum at-reactor storage plus intra-utility transshipment of spent fuel. 8 refs., 8 figs., 10 tabs.

  1. Hybrid Solar Lighting Provides Energy Savings and Reduces Waste Heat

    SciTech Connect (OSTI)

    Lapsa, Melissa Voss [ORNL; Maxey, L Curt [ORNL; Earl, Dennis Duncan [ORNL; Beshears, David L [ORNL; Ward, Christina D [ORNL; Parks, James Edgar [ORNL

    2006-01-01T23:59:59.000Z

    ABSTRACT Artificial lighting is the largest component of electricity use in commercial U.S. buildings. Hybrid solar lighting (HSL) provides an exciting new means of reducing energy consumption while also delivering significant ancillary benefits associated with natural lighting in buildings. As more than half of all federal facilities are in the Sunbelt region (defined as having an average direct solar radiation of greater than 4 kWh/m2/day) and as more than half of all square footage available in federal buildings is also in the Sunbelt, HSL is an excellent technology fit for federal facilities. The HSL technology uses a rooftop, 4-ft-wide dish and secondary mirror that track the sun throughout the day (Fig. 1). The collector system focuses the sunlight onto 127 optical fibers. The fibers serve as flexible light pipes and are connected to hybrid light fixtures that have special diffusion rods that spread out the light in all directions. One collector powers about eight hybrid light fixtures-which can illuminate about 1,000 square feet. The system tracks at 0.1 accuracy, required by the two-mirror geometry to keep the focused beam on the fiber bundle. When sunlight is plentiful, the optical fibers in the luminaires provide all or most of the light needed in an area. During times of little or no sunlight, a sensor controls the intensity of the artificial lamps to maintain a desired illumination level. Unlike conventional electric lamps, the natural light produces little to no waste heat and is cool to the touch. This is because the system's solar collector removes the infrared light-the part of the spectrum that generates a lot of the heat in conventional bulbs-from the sunlight.

  2. How intense quality control improves hydraulic fracturing

    SciTech Connect (OSTI)

    Ely, J.W. [Ely and Associates, Inc., Houston, TX (United States)

    1996-11-01T23:59:59.000Z

    Not unlike the subject of Forced Closure, Intense Quality Control is probably misnamed. What actually is discussed in this article is pilot testing of the fracturing fluids actually pumped at in-situ conditions of temperature and shear. Presented here is development of the need for onsite testing, equipment used, shear and viscosity curves from several jobs showing what went wrong that would otherwise not have been known, and a discussion of borate gel fluids.

  3. Intensive Variables & Nanostructuring in Magnetostructural Materials

    SciTech Connect (OSTI)

    Lewis, Laura

    2014-08-13T23:59:59.000Z

    Over the course of this project, fundamental inquiry was carried out to investigate, understand and predict the effects of intensive variables, including the structural scale, on magnetostructural phase transitions in the model system of equiatomic FeRh. These transitions comprise simultaneous magnetic and structural phase changes that have their origins in very strong orbital-lattice coupling and thus may be driven by a plurality of effects.

  4. Methods for preparation of nanocrystalline rare earth phosphates for lighting applications

    SciTech Connect (OSTI)

    Comanzo, Holly Ann; Manoharan, Mohan; Martins Loureiro, Sergio Paulo; Setlur, Anant Achyut; Srivastava, Alok Mani

    2013-04-16T23:59:59.000Z

    Disclosed here are methods for the preparation of optionally activated nanocrystalline rare earth phosphates. The optionally activated nanocrystalline rare earth phosphates may be used as one or more of quantum-splitting phosphor, visible-light emitting phosphor, vacuum-UV absorbing phosphor, and UV-emitting phosphor. Also disclosed herein are discharge lamps comprising the optionally activated nanocrystalline rare earth phosphates provided by these methods.

  5. THE NEAR-INFRARED BACKGROUND INTENSITY AND ANISOTROPIES DURING THE EPOCH OF REIONIZATION

    SciTech Connect (OSTI)

    Cooray, Asantha; Gong Yan; Smidt, Joseph [Department of Physics and Astronomy, University of California, Irvine, CA 92697 (United States); Santos, Mario G. [CENTRA, Instituto Superior Tecnico, Technical University of Lisbon, Lisboa 1049-001 (Portugal)

    2012-09-01T23:59:59.000Z

    A fraction of the extragalactic near-infrared (near-IR) background light involves redshifted photons from the ultraviolet (UV) emission from galaxies present during reionization at redshifts above 6. The absolute intensity and the anisotropies of the near-IR background provide an observational probe of the first-light galaxies and their spatial distribution. We estimate the extragalactic background light intensity during reionization by accounting for the stellar and nebular emission from first-light galaxies. We require the UV photon density from these galaxies to generate a reionization history that is consistent with the optical depth to electron scattering from cosmic microwave background measurements. We also require the bright-end luminosity function (LF) of galaxies in our models to reproduce the measured Lyman-dropout LFs at redshifts of 6-8. The absolute intensity is about 0.1-0.4 nW m{sup -2} sr{sup -1} at the peak of its spectrum at {approx}1.1 {mu}m. We also discuss the anisotropy power spectrum of the near-IR background using a halo model to describe the galaxy distribution. We compare our predictions for the anisotropy power spectrum to existing measurements from deep near-IR imaging data from Spitzer/IRAC, Hubble/NICMOS, and AKARI. The predicted rms fluctuations at tens of arcminute angular scales are roughly an order of magnitude smaller than the existing measurements. While strong arguments have been made that the measured fluctuations do not have an origin involving faint low-redshift galaxies, we find that measurements in the literature are also incompatible with galaxies present during the era of reionization. The measured near-IR background anisotropies remain unexplained with an unknown origin.

  6. Nonequilibrium lighting plasmas

    SciTech Connect (OSTI)

    Dakin, J.T. (GE Lighting, Nela Park, Cleveland, OH (US))

    1991-12-01T23:59:59.000Z

    In this paper the science of a variety of devices employing nonequilibrium lighting plasmas is reviewed. The devices include the fluorescent lamp, the low-pressure sodium lamp, the neon sign, ultraviolet lamps, glow indicators, and a variety of devices used by spectroscopists, such as the hollow cathode light source. The plasma conditions in representative commercial devices are described. Recent research on the electron gas, the role of heavy particles, spatial and temporal inhomogeneities, and new electrodeless excitation schemes is reviewed. Areas of future activity are expected to be in new applications of high-frequency electronics to commercial devices, new laser-based diagnostics of plasma conditions, and more sophisticated models requiring more reliable and extensive rate coefficient data.

  7. Light cone matrix product

    SciTech Connect (OSTI)

    Hastings, Matthew B [Los Alamos National Laboratory

    2009-01-01T23:59:59.000Z

    We show how to combine the light-cone and matrix product algorithms to simulate quantum systems far from equilibrium for long times. For the case of the XXZ spin chain at {Delta} = 0.5, we simulate to a time of {approx} 22.5. While part of the long simulation time is due to the use of the light-cone method, we also describe a modification of the infinite time-evolving bond decimation algorithm with improved numerical stability, and we describe how to incorporate symmetry into this algorithm. While statistical sampling error means that we are not yet able to make a definite statement, the behavior of the simulation at long times indicates the appearance of either 'revivals' in the order parameter as predicted by Hastings and Levitov (e-print arXiv:0806.4283) or of a distinct shoulder in the decay of the order parameter.

  8. OLEDS FOR GENERAL LIGHTING

    SciTech Connect (OSTI)

    Anil Duggal; Don Foust; Chris Heller; Bill Nealon; Larry Turner; Joe Shiang; Nick Baynes; Tim Butler; Nalin Patel

    2004-02-29T23:59:59.000Z

    The goal of this program was to reduce the long term technical risks that were keeping the lighting industry from embracing and developing organic light-emitting diode (OLED) technology for general illumination. The specific goal was to develop OLEDs for lighting to the point where it was possible to demonstrate a large area white light panel with brightness and light quality comparable to a fluorescence source and with an efficacy comparable to that of an incandescent source. it was recognized that achieving this would require significant advances in three area: (1) the improvement of white light quality for illumination, (2) the improvement of OLED energy efficiency at high brightness, and (3) the development of cost-effective large area fabrication techniques. The program was organized such that, each year, a ''deliverable'' device would be fabricated which demonstrated progress in one or more of the three critical research areas. In the first year (2001), effort concentrated on developing an OLED capable of generating high illumination-quality white light. Ultimately, a down-conversion method where a blue OLED was coupled with various down-conversion layers was chosen. Various color and scattering models were developed to aid in material development and device optimization. The first year utilized this approach to deliver a 1 inch x 1 inch OLED with higher illumination-quality than available fluorescent sources. A picture of this device is shown and performance metrics are listed. To their knowledge, this was the first demonstration of true illumination-quality light from an OLED. During the second year, effort concentrated on developing a scalable approach to large area devices. A novel device architecture consisting of dividing the device area into smaller elements that are monolithically connected in series was developed. In the course of this development, it was realized that, in addition to being scalable, this approach made the device tolerant to the most common OLED defect--electrical shorts. This architecture enabled the fabrication of a 6 inch x 6 inch OLED deliverable for 2002. A picture of this deliverable is shown and the performance metrics are listed. At the time, this was the highest efficiency, highest lumen output illumination-quality OLED in existence. The third year effort concentrated on improving the fabrication yield of the 6 inch x 6 inch devices and improving the underlying blue device efficiency. An efficiency breakthrough was achieved through the invention of a new device structure such that now 15 lumen per watt devices could be fabricated. A 2 feet x 2 feet OLED panel consisting of sixteen 6 inch x 6 inch high efficiency devices tiled together was then fabricated. Pictures of this panel are shown with performance metrics listed. This panel met all project objectives and was the final deliverable for the project. It is now the highest efficiency, highest lumen output, illumination-quality OLED in existence.

  9. Fusion pumped light source

    DOE Patents [OSTI]

    Pappas, Daniel S. (Los Alamos, NM)

    1989-01-01T23:59:59.000Z

    Apparatus is provided for generating energy in the form of light radiation. A fusion reactor is provided for generating a long, or continuous, pulse of high-energy neutrons. The neutron flux is coupled directly with the lasing medium. The lasing medium includes a first component selected from Group O of the periodic table of the elements and having a high inelastic scattering cross section. Gamma radiation from the inelastic scattering reactions interacts with the first component to excite the first component, which decays by photon emission at a first output wavelength. The first output wavelength may be shifted to a second output wavelength using a second liquid component responsive to the first output wavelength. The light outputs may be converted to a coherent laser output by incorporating conventional optics adjacent the laser medium.

  10. Nanometer-scale ablation using focused, coherent extreme ultraviolet/soft x-ray light

    DOE Patents [OSTI]

    Menoni, Carmen S. (Fort Collins, CO); Rocca, Jorge J. (Fort Collins, CO); Vaschenko, Georgiy (San Diego, CA); Bloom, Scott (Encinitas, CA); Anderson, Erik H. (El Cerrito, CA); Chao, Weilun (El Cerrito, CA); Hemberg, Oscar (Stockholm, SE)

    2011-04-26T23:59:59.000Z

    Ablation of holes having diameters as small as 82 nm and having clean walls was obtained in a poly(methyl methacrylate) on a silicon substrate by focusing pulses from a Ne-like Ar, 46.9 nm wavelength, capillary-discharge laser using a freestanding Fresnel zone plate diffracting into third order is described. Spectroscopic analysis of light from the ablation has also been performed. These results demonstrate the use of focused coherent EUV/SXR light for the direct nanoscale patterning of materials.

  11. Fan-beam intensity modulated proton therapy

    SciTech Connect (OSTI)

    Hill, Patrick [Department of Radiation Oncology, University of Iowa Hospitals and Clinics, Iowa City, Iowa 52242 (United States)] [Department of Radiation Oncology, University of Iowa Hospitals and Clinics, Iowa City, Iowa 52242 (United States); Westerly, David [Department of Radiation Oncology, University of Colorado School of Medicine, Aurora, Colorado 80045 (United States)] [Department of Radiation Oncology, University of Colorado School of Medicine, Aurora, Colorado 80045 (United States); Mackie, Thomas [Medical Devices, Morgridge Institute for Research, University of Wisconsin, Madison, Wisconsin 53715 (United States)] [Medical Devices, Morgridge Institute for Research, University of Wisconsin, Madison, Wisconsin 53715 (United States)

    2013-11-15T23:59:59.000Z

    Purpose: This paper presents a concept for a proton therapy system capable of delivering intensity modulated proton therapy using a fan beam of protons. This system would allow present and future gantry-based facilities to deliver state-of-the-art proton therapy with the greater normal tissue sparing made possible by intensity modulation techniques.Methods: A method for producing a divergent fan beam of protons using a pair of electromagnetic quadrupoles is described and particle transport through the quadrupole doublet is simulated using a commercially available software package. To manipulate the fan beam of protons, a modulation device is developed. This modulator inserts or retracts acrylic leaves of varying thickness from subsections of the fan beam. Each subsection, or beam channel, creates what effectively becomes a beam spot within the fan area. Each channel is able to provide 0–255 mm of range shift for its associated beam spot, or stop the beam and act as an intensity modulator. Results of particle transport simulations through the quadrupole system are incorporated into the MCNPX Monte Carlo transport code along with a model of the range and intensity modulation device. Several design parameters were investigated and optimized, culminating in the ability to create topotherapy treatment plans using distal-edge tracking on both phantom and patient datasets.Results: Beam transport calculations show that a pair of electromagnetic quadrupoles can be used to create a divergent fan beam of 200 MeV protons over a distance of 2.1 m. The quadrupole lengths were 30 and 48 cm, respectively, with transverse field gradients less than 20 T/m, which is within the range of water-cooled magnets for the quadrupole radii used. MCNPX simulations of topotherapy treatment plans suggest that, when using the distal edge tracking delivery method, many delivery angles are more important than insisting on narrow beam channel widths in order to obtain conformal target coverage. Overall, the sharp distal falloff of a proton depth-dose distribution was found to provide sufficient control over the dose distribution to meet objectives, even with coarse lateral resolution and channel widths as large as 2 cm. Treatment plans on both phantom and patient data show that dose conformity suffers when treatments are delivered from less than approximately ten angles. Treatment time for a sample prostate delivery is estimated to be on the order of 10 min, and neutron production is estimated to be comparable to that found for existing collimated systems.Conclusions: Fan beam proton therapy is a method of delivering intensity modulated proton therapy which may be employed as an alternative to magnetic scanning systems. A fan beam of protons can be created by a set of quadrupole magnets and modified by a dual-purpose range and intensity modulator. This can be used to deliver inversely planned treatments, with spot intensities optimized to meet user defined dose objectives. Additionally, the ability of a fan beam delivery system to effectively treat multiple beam spots simultaneously may provide advantages as compared to spot scanning deliveries.

  12. Modeling and Validation of Performance Limitations for the Optimal Design of Interferometric and Intensity-Modulated Fiber Optic Displacement Sensors

    SciTech Connect (OSTI)

    Moro, Erik A. [Los Alamos National Laboratory

    2012-06-07T23:59:59.000Z

    Optical fiber sensors offer advantages over traditional electromechanical sensors, making them particularly well-suited for certain measurement applications. Generally speaking, optical fiber sensors respond to a desired measurand through modulation of an optical signal's intensity, phase, or wavelength. Practically, non-contacting fiber optic displacement sensors are limited to intensity-modulated and interferometric (or phase-modulated) methodologies. Intensity-modulated fiber optic displacement sensors relate target displacement to a power measurement. The simplest intensity-modulated sensor architectures are not robust to environmental and hardware fluctuations, since such variability may cause changes in the measured power level that falsely indicate target displacement. Differential intensity-modulated sensors have been implemented, offering robustness to such intensity fluctuations, and the speed of these sensors is limited only by the combined speed of the photodetection hardware and the data acquisition system (kHz-MHz). The primary disadvantages of intensity-modulated sensing are the relatively low accuracy (?m-mm for low-power sensors) and the lack of robustness, which consequently must be designed, often with great difficulty, into the sensor's architecture. White light interferometric displacement sensors, on the other hand, offer increased accuracy and robustness. Unlike their monochromatic-interferometer counterparts, white light interferometric sensors offer absolute, unambiguous displacement measurements over large displacement ranges (cm for low-power, 5 mW, sources), necessitating no initial calibration, and requiring no environmental or feedback control. The primary disadvantage of white light interferometric displacement sensors is that their utility in dynamic testing scenarios is limited, both by hardware bandwidth and by their inherent high-sensitivity to Doppler-effects. The decision of whether to use either an intensity-modulated interferometric sensor depends on an appropriate performance function (e.g., desired displacement range, accuracy, robustness, etc.). In this dissertation, the performance limitations of a bundled differential intensity-modulated displacement sensor are analyzed, where the bundling configuration has been designed to optimize performance. The performance limitations of a white light Fabry-Perot displacement sensor are also analyzed. Both these sensors are non-contacting, but they have access to different regions of the performance-space. Further, both these sensors have different degrees of sensitivity to experimental uncertainty. Made in conjunction with careful analysis, the decision of which sensor to deploy need not be an uninformed one.

  13. Turbo-Charged Lighting Design

    E-Print Network [OSTI]

    Clark, W. H. II

    TURBO-CHARGED LIGHTING DESIGN William H. Clark II Design Engineer O'Connell Robertson & Assoc Austin/ Texas ABSTRACT The task of the lighting designer has become very complex, involving thousands of choices for fixture types and hundreds...

  14. Faster than Light Quantum Communication

    E-Print Network [OSTI]

    A. Y. Shiekh

    2008-04-05T23:59:59.000Z

    Faster than light communication might be possible using the collapse of the quantum wave-function without any accompanying paradoxes.

  15. Webinar: Fuel Cell Mobile Lighting

    Broader source: Energy.gov [DOE]

    Video recording of the Fuel Cell Technologies Office webinar, Fuel Cell Mobile Lighting, originally presented on November 13, 2012.

  16. Photodetector with enhanced light absorption

    DOE Patents [OSTI]

    Kane, James (Lawrenceville, NJ)

    1985-01-01T23:59:59.000Z

    A photodetector including a light transmissive electrically conducting layer having a textured surface with a semiconductor body thereon. This layer traps incident light thereby enhancing the absorption of light by the semiconductor body. A photodetector comprising a textured light transmissive electrically conducting layer of SnO.sub.2 and a body of hydrogenated amorphous silicon has a conversion efficiency about fifty percent greater than that of comparative cells. The invention also includes a method of fabricating the photodetector of the invention.

  17. COMMENTS ON THE SEARCH FOR ELECTROSTATIC DISCHARGES ON MARS

    SciTech Connect (OSTI)

    Renno, Nilton O.; Ruf, Christopher S., E-mail: renno@alum.mit.edu [Atmospheric, Oceanic and Space Sciences, University of Michigan, Ann Arbor, MI (United States)

    2012-12-20T23:59:59.000Z

    Ruf et al. used the Deep Space Network (DSN) to search for the emission of non-thermal radiation by martian dust storms, theoretically predicted by Renno et al. They detected the emission of non-thermal radiation that they were searching for, but were surprised that it contained spectral peaks suggesting modulation at various frequencies and their harmonics. Ruf et al. hypothesized that the emission of non-thermal radiation was caused by electric discharges in a deep convective dust storm, modulated by Schumann resonances (SRs). Anderson et al. used the Allen Telescope Array (ATA) to search for similar emissions. They stated that they found only radio frequency interference (RFI) during their search for non-thermal emission by martian dust storms and implicitly suggested that the signal detected by Ruf et al. was also RFI. However, their search was not conducted during the dust storm season when deep convective storms are most likely to occur. Here, we show that the ubiquitous dust devils and small-scale dust storms that were instead likely present during their observations are too shallow to excite SRs and produce the signals detected by Ruf et al. We also show that the spectral and temporal behavior of the signals detected by Anderson et al. corroborates the idea that they originated from man-made pulse-modulated telecommunication signals rather than martian electric discharges. In contrast, an identical presentation of the signals detected by Ruf et al. demonstrates that they do not resemble man-made signals. The presentation indicates that the DSN signals were consistent with modulation by martian SRs, as originally hypothesized by Ruf et al. We propose that a more comprehensive search for electrostatic discharges be conducted with either the ATA or DSN during a future martian dust storm season to test the hypothesis proposed by Ruf et al.

  18. Surface charge in dielectric barrier discharge plasma actuators

    SciTech Connect (OSTI)

    Opaits, D. F.; Shneider, M. N.; Miles, Richard B. [Department of Mechanical and Aerospace Engineering, Princeton University, Princeton, New Jersey 08544 (United States); Likhanskii, A. V. [Pennsylvania State University, University Park, Pennsylvania 16802 (United States); Macheret, S. O. [Lockheed Martin Aeronautics Company, Palmdale, California 93599 (United States)

    2008-07-15T23:59:59.000Z

    Direct measurements of the dielectric surface potential and its dynamics in asymmetric dielectric barrier discharge (DBD) plasma actuators show that the charge builds up at the dielectric surface and extends far downstream of the plasma. The surface charge persists for a long time (tens of minutes) after the driving voltage has been turned off. For a sinusoidal voltage waveform, the dielectric surface charges positively. With the voltage waveform consisting of nanosecond pulses superimposed on a dc bias, the sign of the dielectric surface charge is the same as the sign (polarity) of the bias voltage. The surface charging significantly affects DBD plasma actuator performance.

  19. Ethanol reforming in non-equilibrium plasma of glow discharge

    E-Print Network [OSTI]

    Levko, D

    2012-01-01T23:59:59.000Z

    The results of a detailed kinetic study of the main plasma chemical processes in non-equilibrium ethanol/argon plasma are presented. It is shown that at the beginning of the discharge the molecular hydrogen is mainly generated in the reaction of ethanol H-abstraction. Later hydrogen is formed from active H, CH2OH and CH3CHOH and formaldehyde. Comparison with experimental data has shown that the used kinetic mechanism predicts well the concentrations of main species at the reactor outlet.

  20. Synthesizing aluminum particles towards controlling electrostatic discharge ignition sensitivity

    SciTech Connect (OSTI)

    Eric S. Collins; Jeffery P. Gesner; Michelle L. Pantoya; Michael A. Daniels

    2014-02-01T23:59:59.000Z

    Aluminum particles were synthesized with shell thicknesses ranging from 2.7 to 8.3 nm and a constant diameter of 95 nm. These fuel particles were combined with molybdenum trioxide particles and the electrostatic discharge (ESD) sensitivity of the mixture was measured. Results show ignition delay increased as the alumina shell thickness increased. These results correlated with electrical resistivity measurements of the mixture which increased with alumina concentration. A model was developed using COMSOL for ignition of a single Al particle. The ignition delay in the model was consistent with the experimental results suggesting that the primary ESD ignition mechanism is joule heating.

  1. MANDATORY MEASURES OUTDOOR LIGHTING CONTROLS

    E-Print Network [OSTI]

    California at Davis, University of

    MANDATORY MEASURES OUTDOOR LIGHTING CONTROLS (Reference: Sub-Chapter 4, Section 130.2) #12;SECTION level of each multi-tier garage. · General lighting must have occupant sensing controls with at least one control step between 20% and 50% of design lighting power · No more than 500 watts of rated

  2. MANDATORY MEASURES OUTDOOR LIGHTING CONTROLS

    E-Print Network [OSTI]

    California at Davis, University of

    MANDATORY MEASURES OUTDOOR LIGHTING CONTROLS (Reference: Sub-Chapter 4, Section 130.2) #12;SECTION 5 Additions and Alterations Any alteration that increases the connected lighting load must meet all No measures required OUTDOOR LIGHTING11/20/2014 #12;SECTION 5 BACKLIGHT, UPLIGHT, AND GLARE (BUG) RATINGS

  3. MANDATORY MEASURES OUTDOOR LIGHTING CONTROLS

    E-Print Network [OSTI]

    California at Davis, University of

    MANDATORY MEASURES OUTDOOR LIGHTING CONTROLS (Reference: Sub-Chapter 4, Section 130.2) #12;SECTION performance in relation to lighting trespass, sky glow, and high angle brightness. This is necessary in order to reduce light pollution, which has a negative effect on wildlife and the surrounding environments

  4. Arnold Schwarzenegger, LIGHTING RESEARCH PROGRAM

    E-Print Network [OSTI]

    ;#12;Prepared By: Lighting Research Center Andrew Bierman, Project Lead Troy, New York 12180 Managed ByArnold Schwarzenegger, Governor LIGHTING RESEARCH PROGRAM PROJECT 3.2 ENERGY EFFICIENT LOAD- SHEDDING LIGHTING TECHNOLOGY Prepared For: California Energy Commission Public Interest Energy Research

  5. STATE OF CALIFORNIA RESIDENTIAL LIGHTING

    E-Print Network [OSTI]

    STATE OF CALIFORNIA RESIDENTIAL LIGHTING CEC-CF-6R-LTG-01 (Revised 08/09) CALIFORNIA ENERGY COMMISSION INSTALLATION CERTIFICATE CF-6R-LTG-01 Residential Lighting (Page 1 of 6) Site Address: Enforcement Agency: Permit Number: 2008 Residential Compliance Forms August 2009 1. Kitchen Lighting Does project

  6. On the Velocity and Intensity Line Asymmetries

    E-Print Network [OSTI]

    M. Gabriel

    1997-10-01T23:59:59.000Z

    We show that, if solar 5 min. oscillations are excited by convection in the upper layers of the convective envelope, it is impossible to explain the opposite line asymmetries observed in the velocity and intensity spectra with assumptions on the dissipations which reduce the problem to a second order one. The interpretation of that observation requires to solve the full non-adiabatic problem which is of the fourth or sixth order. We also analyze the causes of line asymmetries in the frame of the general problem and we show that to locate the source, it is better to study line asymmetries not too far from line centers.

  7. Highly Efficient Silicon Light Emitting Diode

    E-Print Network [OSTI]

    Leminh Holleman Wallinga; P. Leminh; J. Holleman; H. Wallinga

    2000-01-01T23:59:59.000Z

    In this paper, we describe the fabrication, using standard silicon processing techniques, of silicon light-emitting diodes (LED) that efficiently emit photons with energy around the silicon bandgap. The improved efficiency had been explained by the spatial confinement of charge carriers due to a local strain field that is formed by dislocation loop arrays. The dependence of device electroluminescent properties on the annealing conditions is carefully examined as a high temperature process has profound influence on these dislocations. Increased luminescent intensity at higher device temperature, together with pure diffusion current conduction mechanism evidently shows the influence of the dislocation loops. The electrical properties of the diode are reasonable with low leakage reverse current.

  8. Blue-green and green phosphors for lighting applications

    DOE Patents [OSTI]

    Setlur, Anant Achyut; Chandran, Ramachandran Gopi; Henderson, Claire Susan; Nammalwar, Pransanth Kumar; Radkov, Emil

    2012-12-11T23:59:59.000Z

    Embodiments of the present techniques provide a related family of phosphors that may be used in lighting systems to generate blue or blue-green light. The phosphors include systems having a general formula of: ((Sr.sub.1-zM.sub.z).sub.1-(x+w)A.sub.wCe.sub.x).sub.3(Al.sub.1-ySi.s- ub.y)O.sub.4+y+3(x-w)F.sub.1-y-3(x-w) (I), wherein 0intensity across a wide range of temperatures. The phosphors may be used in lighting systems, such as LEDs and fluorescent tubes, among others, to produce blue and blue/green light. Further, the phosphors may be used in blends with other phosphors, or in combined lighting systems, to produce white light suitable for illumination.

  9. Angular distribution of polarized spontaneous emissions and its effect on light extraction behavior in InGaN-based light emitting diodes

    SciTech Connect (OSTI)

    Yuan, Gangcheng; Chen, Xinjuan; Yu, Tongjun, E-mail: tongjun@pku.edu.cn; Lu, Huimin; Chen, Zhizhong; Kang, Xiangning; Wu, Jiejun; Zhang, Guoyi [State Key Laboratory for Artificial Microstructure and Mesoscopic Physics, School of Physics, Peking University, Beijing 100871 (China)

    2014-03-07T23:59:59.000Z

    Angular intensity distributions of differently polarized light sources in multiple quantum wells (MQWs) and their effects on extraction behavior of spontaneous emission from light emitting diode (LED) chips have been studied. Theoretical calculation based on k·p approximation, ray tracing simulation and angular electroluminescence measurement were applied in this work. It is found that the electron-hole recombination in the InGaN MQWs produces a spherical distribution of an s-polarized source and a dumbbell-shaped p-polarized source. Light rays from different polarized sources experience different extraction processes, determining the polarization degree of electro-luminescence and extraction efficiency of LEDs.

  10. Pedestrian Friendly Outdoor Lighting

    SciTech Connect (OSTI)

    Miller, Naomi J.; Koltai, Rita; McGowan, Terry

    2013-12-31T23:59:59.000Z

    This GATEWAY report discusses the problems of pedestrian lighting that occur with all technologies with a focus on the unique optical options and opportunities offered by LEDs through the findings from two pedestrian-focused projects, one at Stanford University in California, and one at the Chautauqua Institution in upstate New York. Incorporating user feedback this report reviews the tradeoffs that must be weighed among visual comfort, color, visibility, efficacy and other factors to stimulate discussion among specifiers, users, energy specialists, and in industry in hopes that new approaches, metrics, and standards can be developed to support pedestrian-focused communities, while reducing energy use.

  11. Lights, Conformational Change... Action!

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: VegetationEquipment Surfaces and Interfaces Sample6, 2011 LawrenceEfeedstocksHomesLighting the

  12. Lighting | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of InspectorConcentrating Solar Powerstories on climateJuno Beach,October,Lighthouse Solar Jump to:Lighting Jump

  13. Ecological Consequences of Artificial Night Lighting

    E-Print Network [OSTI]

    Piselli, Kathy

    2006-01-01T23:59:59.000Z

    of Artificial Night Lighting Catherine Rich and Travisof artificial night lighting. This book provides editedage of modern urban lighting was ushered in. Coincidentally,

  14. LIGHTING CONTROLS: SURVEY OF MARKET POTENTIAL

    E-Print Network [OSTI]

    Verderber, R.R.

    2010-01-01T23:59:59.000Z

    REFERENCES Task Report to Lighting Systems Research,Berkeley Laboratory, "Lighting Control System Market1980). Task Report to Lighting Systems Research, Lawrence

  15. Demand Responsive Lighting: A Scoping Study

    E-Print Network [OSTI]

    Rubinstein, Francis; Kiliccote, Sila

    2007-01-01T23:59:59.000Z

    3 3.0 Previous Experience with Demand Responsive Lighting11 4.3. Prevalence of Lighting13 4.4. Impact of Title 24 on Lighting

  16. Municipal Consortium LED Street Lighting Workshop Presentations...

    Broader source: Energy.gov (indexed) [DOE]

    A Rational View of LM-79 Reports, IES Files, and Product Variation Gary Steinberg, GE Lighting Solutions Solid-State Street Lighting: Calculating Light Loss Factors Dana Beckwith,...

  17. Municipal Consortium LED Street Lighting Workshop Presentations...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    National Association of Energy Services Companies Calculating Light Loss Factors for Solid-State Lighting Systems Chad Stalker, Philips Lumileds Lighting Intro to MSSLC's...

  18. Sandia National Laboratories: Light Creation Materials

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    TechnologiesLight Creation Materials Light Creation Materials Overview of SSL Light Creation Materials Different families of inorganic semiconductor materials can...

  19. Photon echo studies of photosynthetic light harvesting

    E-Print Network [OSTI]

    Read, Elizabeth L.; Lee, Hohjai; Fleming, Graham R.

    2009-01-01T23:59:59.000Z

    of the B800-B820 light-harvesting complex. Proc Natl Acadphotosynthetic light harvesting Elizabeth L. Read Æ Hohjaitransfer events in light harvesting. Here, we outline the

  20. Sandia National Laboratories: Light Creation Materials

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    EFRCOverviewLight Creation Materials Light Creation Materials Overview of SSL Light Creation Materials Different families of inorganic semiconductor materials can contribute to...

  1. The Impact of Intrinsic Heavy Quark Distributions in the Proton on New Physics Searches at the High Intensity Frontier

    SciTech Connect (OSTI)

    Brodsky, Stanley; /SLAC; Gardner, Susan; /Kentucky U.

    2012-02-16T23:59:59.000Z

    The possibility of an intense proton facility, at 'Project X' or elsewhere, will provide many new opportunities for searches for physics beyond the Standard Model. A Project X can serve a yet broader role in the search for new physics, and in this note we highlight the manner in which thus-enabled studies of the flavor structure of the proton, particularly of its intrinsic heavy quark content, facilitate other direct and indirect searches for new physics. Intrinsic heavy quarks in both light and heavy hadrons play a key role in searches for physics BSM with hadrons - and their study at the Intensity Frontier may prove crucial to establishing its existence.

  2. Visible-light active TiO2 for microwave assisted photocatalytic reactions using mercury electrodeless discharge lamps

    E-Print Network [OSTI]

    Cirkva, Vladimir

    activity was evaluated by the degradation of mono-chloroacetic acid in a microwave field using mercury with pure titania, the UV-Vis spectra of Ag+, Zr4+ and VO2+ doped titanium dioxide show significant absorption in visible region. The degradation efficiency of MCAA in a microwave field on these TiO2 layers

  3. A model for the self-pulsing regime of microhollow cathode discharges

    SciTech Connect (OSTI)

    Chabert, P.; Lazzaroni, C.; Rousseau, A. [LPP, Ecole Polytechnique, UPMC, CNRS, Paris XI, 91128 Palaiseau (France)

    2010-12-01T23:59:59.000Z

    Microhollow cathode discharges may operate in different regimes depending of the discharge current. They are subject to relaxation oscillations in the so-called self-pulsing regime in which the discharge oscillates between two quasiequilibria: at low current it remains confined in the microhole whereas it expands on the cathode backside during short high-current pulses. A model based on a nonlinear discharge resistance is proposed to describe the phenomenon. The analysis of the dynamics reveals that the current pulse rises in an extremely short time while the characteristic (longer) decay time is imposed by the resistance when the discharge is expanded outside the hole. It is shown how the nonlinear discharge resistance may be inferred from the experimental current-voltage signals.

  4. Modeling a short dc discharge with thermionic cathode and auxiliary anode

    SciTech Connect (OSTI)

    Bogdanov, E. [St. Petersburg State University, St. Petersburg 199034 (Russian Federation) [St. Petersburg State University, St. Petersburg 199034 (Russian Federation); University ITMO, Kronverkskiy pr. 49, St. Petersburg 197101 (Russian Federation); Demidov, V. I. [St. Petersburg State University, St. Petersburg 199034 (Russian Federation) [St. Petersburg State University, St. Petersburg 199034 (Russian Federation); West Virginia University, Morgantown, West Virginia 26506 (United States); Kaganovich, I. D. [Princeton Plasma Physics Laboratory, Princeton, New Jersey 08543 (United States)] [Princeton Plasma Physics Laboratory, Princeton, New Jersey 08543 (United States); Koepke, M. E. [West Virginia University, Morgantown, West Virginia 26506 (United States)] [West Virginia University, Morgantown, West Virginia 26506 (United States); Kudryavtsev, A. A. [St. Petersburg State University, St. Petersburg 199034 (Russian Federation)] [St. Petersburg State University, St. Petersburg 199034 (Russian Federation)

    2013-10-15T23:59:59.000Z

    A short dc discharge with a thermionic cathode can be used as a current and voltage stabilizer, but is subject to current oscillation. If instead of one anode two anodes are used, the current oscillations can be reduced. We have developed a kinetic model of such a discharge with two anodes, where the primary anode has a small opening for passing a fraction of the discharge current to an auxiliary anode. The model demonstrates that the current-voltage relationship of the discharge with two anodes is characterized everywhere by positive slope, i.e., positive differential resistance. Therefore, the discharge with two anodes is expected to be stable to the spontaneous oscillation in current that is induced by negative differential resistance. As a result, such a discharge can be used in an engineering application that requires stable plasma, such as a current and voltage stabilizer.

  5. China's energy intensity and its determinants at the provincial level

    E-Print Network [OSTI]

    Zhang, Xin, S.M. Massachusetts Institute of Technology

    2009-01-01T23:59:59.000Z

    Energy intensity is defined as the amount of energy consumed per dollar of GDP (Gross Domestic Product). The People's Republic of China's (China's) energy intensity has been declining significantly since the late 1970s. ...

  6. Present and Near-Future Reflected Light Searches for Close-In Planets

    E-Print Network [OSTI]

    David Charbonneau; Robert W. Noyes

    2000-02-26T23:59:59.000Z

    Close-in extrasolar giant planets may be directly detectable by their reflected light, due to the proximity of the planet to the illuminating star. The spectrum of the system will contain a reflected light component that varies in amplitude and Doppler shift as the planet orbits the star. Intensive searches for this effect have been carried out for only one extrasolar planet system, tau Boo. There exist several other attractive targets, including the transiting planet system HD 209458.

  7. IC-BASED CONTROLS FOR ENERGY-EFFICIENT LIGHTING

    SciTech Connect (OSTI)

    Richard Zhang

    2005-03-01T23:59:59.000Z

    A new approach for driving high frequency energy saving ballasts is developed and documented in this report. The developed approach utilizes an IC-based platform that provides the benefits of reduced system cost, reduced ballast size, and universal application to a wide range of lamp technologies, such as linear fluorescent lamps (LFL), compact fluorescent lamps (CFL) and high intensity discharge lamps (HID). The control IC chip set developed for the platform includes dual low voltage (LV) IC gate drive that provides gate drive for high and low side power switches in typical ballast circuits, and ballast controller IC that provides control functionalities optimal for different lamps and digital interface for future extension to more sophisticated control and communication.

  8. E-Print Network 3.0 - accelerated hypofractionated intensity...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    (IMRT) de- pendends on finding... technologies. I. INTRODUCTION Intensity modulated radiation ... Source: Censor, Yair - Department of Mathematics, University of Haifa...

  9. ANTENNA-COUPLED LIGHT-MATTER INTERACTIONS

    SciTech Connect (OSTI)

    NOVOTNY, LUKAS

    2014-01-10T23:59:59.000Z

    This project is focused on antenna-coupled photon emission from single quantum emitters. The properties of optical antennas are tailored to control different photophysical parameters, such as the excited state lifetime, the saturation intensity, and the quantum yield [3]. Using a single molecule coupled to an optical antenna whose position and properties can be controllably adjusted we established a detailed and quantitative understanding of light-matter interactions in nanoscale environments. We have studied various quantum emitters: single molecules [11], quantum dots [7], rareearth ions [2], and NV centers in diamond [19]. We have systematically studied the interaction of these emitters with optical antennas. The overall objective was to establish a high-level of control over the light-matter interaction. In order to eliminate the coupling to the environment, we have taken a step further and explored the possibility of levitating the quantum emitter in high vacuum. What started as a side-project soon became a main activity in our research program and led us to the demonstration of vacuum trapping and cooling of a nanoscale particle [14].

  10. Title of Dissertation: CONTROL AND TRANSPORT OF INTENSE ELECTRON BEAMS

    E-Print Network [OSTI]

    Anlage, Steven

    ABSTRACT Title of Dissertation: CONTROL AND TRANSPORT OF INTENSE ELECTRON BEAMS Hui Li, Doctor Engineering The transport of intense beams for advanced accelerator applications with high-intensity beams of beam characteristics over long distances. The University of Maryland Electron Ring (UMER), which uses

  11. AN INTENSE LOW ENERGY MUON SOURCE FOR THE MUON COLLIDER

    E-Print Network [OSTI]

    McDonald, Kirk

    AN INTENSE LOW ENERGY MUON SOURCE FOR THE MUON COLLIDER D. Taqqu Paul Scherrer Institut, Villigen, CH Abstract A scheme for obtaining an intense source of low energy muons is described. It is based of the decay muons an intense intermediate energy muon beam is obtained. For the specific case of negative

  12. Aluminium plasma production at high laser intensity

    SciTech Connect (OSTI)

    Torrisi, L.; Cutroneo, M. [Dip.to di Fisica e S.d.T. Università di Messina, V.S. d'Alcontres 31, 98166 S. Agata (Italy)

    2014-02-28T23:59:59.000Z

    Thick and thin films of Al targets were irradiated in vacuum with iodine laser at 1315?nm wavelength, 300 ps pulse duration at a maximum intensity of about 10{sup 16}?W/cm{sup 2} by varying the pulse energy and focal position. The laser-generated plasma was monitored in forward and backward directions by using ion collectors, SiC detectors, Thomson parabola spectrometer, and X-ray streak camera. Ion emission shows maximum proton energy of about 4?MeV in self-focusing conditions and a maximum Al ion energy of about 50?MeV. An evaluation of the electric field driving ions in conditions of target normal sheath acceleration is given.

  13. Position, rotation, and intensity invariant recognizing method

    DOE Patents [OSTI]

    Ochoa, Ellen (Pleasanton, CA); Schils, George F. (San Ramon, CA); Sweeney, Donald W. (Alamo, CA)

    1989-01-01T23:59:59.000Z

    A method for recognizing the presence of a particular target in a field of view which is target position, rotation, and intensity invariant includes the preparing of a target-specific invariant filter from a combination of all eigen-modes of a pattern of the particular target. Coherent radiation from the field of view is then imaged into an optical correlator in which the invariant filter is located. The invariant filter is rotated in the frequency plane of the optical correlator in order to produce a constant-amplitude rotational response in a correlation output plane when the particular target is present in the field of view. Any constant response is thus detected in the output The U.S. Government has rights in this invention pursuant to Contract No. DE-AC04-76DP00789 between the U.S. Department of Energy and AT&T Technologies, Inc.

  14. THE CENTER FOR DATA INTENSIVE COMPUTING

    SciTech Connect (OSTI)

    GLIMM,J.

    2002-11-01T23:59:59.000Z

    CDIC will provide state-of-the-art computational and computer science for the Laboratory and for the broader DOE and scientific community. We achieve this goal by performing advanced scientific computing research in the Laboratory's mission areas of High Energy and Nuclear Physics, Biological and Environmental Research, and Basic Energy Sciences. We also assist other groups at the Laboratory to reach new levels of achievement in computing. We are ''data intensive'' because the production and manipulation of large quantities of data are hallmarks of scientific research in the 21st century and are intrinsic features of major programs at Brookhaven. An integral part of our activity to accomplish this mission will be a close collaboration with the University at Stony Brook.

  15. Electronic and intraband optical properties of single quantum rings under intense laser field radiation

    SciTech Connect (OSTI)

    Radu, A. [Department of Physics, Politehnica University of Bucharest, 313 Splaiul Independentei, Bucharest RO-060042 (Romania); Kirakosyan, A. A.; Baghramyan, H. M.; Barseghyan, M. G., E-mail: mbarsegh@ysu.am [Department of Solid State Physics, Yerevan State University, Alex Manoogian 1, 0025 Yerevan (Armenia); Laroze, D. [Instituto de Alta Investigación, Universidad de Tarapacá, Casilla 7D, Arica (Chile)

    2014-09-07T23:59:59.000Z

    The influence of an intense laser field on one-electron states and intraband optical absorption coefficients is investigated in two-dimensional GaAs/Ga{sub 0.7}Al{sub 0.3}As quantum rings. An analytical expression of the effective lateral confining potential induced by the laser field is obtained. The one-electron energy spectrum and wave functions are found using the effective mass approximation and exact diagonalization technique. We have shown that changes in the incident light polarization lead to blue- or redshifts in the intraband optical absorption spectrum. Moreover, we found that only blueshift is obtained with increasing outer radius of the quantum ring.

  16. Regulations For State Administration Of The National Pollutant Discharge Elimination System (Arkansas)

    Broader source: Energy.gov [DOE]

    The Regulations For State Administration Of The National Pollutant Discharge Elimination System (NPDES) is created Pursuant to the provisions of the Arkansas Water and Air Pollution Control Act,...

  17. Long range temporal correlation in the chaotic oscillations of a dc glow discharge plasma

    SciTech Connect (OSTI)

    Lahiri, S. [Dinabandhu Mahavidyalaya, Bongaon, North 24 Parganas, Kolkata 743235 (India); Roychowdhury, D. [Techno India, EM4/1 Sector V, Salt Lake, Kolkata 700091 (India); Sekar Iyengar, A. N. [Plasma Physics Division, Saha Institute of Nuclear Physics, 1/AF Bidhannagar, Kolkata 700064 (India)

    2012-08-15T23:59:59.000Z

    Long range temporal correlations in the fluctuations of the plasma floating potentials (measured using a Langmuir probe) are investigated in a dc glow discharge plasma. Keeping the neutral pressure constant, the discharge voltage was varied and at the formation of the plasma, quasi periodic oscillations were excited and on further increase of the discharge voltage they became chaotic (irregular) beyond a threshold voltage. We compared the Lyapunov exponent with the Hurst exponent obtained from R/S statistics which showed an opposite behaviour at the transition point. These results are perhaps new since we have not come across such comparative analysis for chaotic oscillations in a glow discharge plasma before.

  18. Self-excited nonlinear plasma series resonance oscillations in geometrically symmetric capacitively coupled radio frequency discharges

    SciTech Connect (OSTI)

    Donko, Z. [Research Institute for Solid State Physics and Optics, Hungarian Academy of Sciences, P.O. Box 49, H-1525 Budapest (Hungary); Schulze, J.; Czarnetzki, U.; Luggenhoelscher, D. [Institute for Plasma and Atomic Physics, Ruhr-University Bochum, Bochum 44780 (Germany)

    2009-03-30T23:59:59.000Z

    At low pressures, nonlinear self-excited plasma series resonance (PSR) oscillations are known to drastically enhance electron heating in geometrically asymmetric capacitively coupled radio frequency discharges by nonlinear electron resonance heating (NERH). Here we demonstrate via particle-in-cell simulations that high-frequency PSR oscillations can also be excited in geometrically symmetric discharges if the driving voltage waveform makes the discharge electrically asymmetric. This can be achieved by a dual-frequency (f+2f) excitation, when PSR oscillations and NERH are turned on and off depending on the electrical discharge asymmetry, controlled by the phase difference of the driving frequencies.

  19. E-Print Network 3.0 - assisted discharge cleaning Sample Search...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    will discharge to a gravel bed for absorption into the ground. 99 Source: Pint, Bruce A. - Materials Science & Technology Division, Oak Ridge National Laboratory...

  20. E-Print Network 3.0 - act thermal discharge Sample Search Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    has been investigated using a hollow cathode discharge Source: Howard, John - Plasma Research Laboratory, Research School of Physical Sciences and Engineering, Australian...

  1. Active electron energy distribution function control in direct current discharge using an auxiliary electrode

    SciTech Connect (OSTI)

    Schweigert, I. V. [Institute of Theoretical and Applied Mechanics, Novosibirsk 630090 (Russian Federation) [Institute of Theoretical and Applied Mechanics, Novosibirsk 630090 (Russian Federation); George Washington University, Washington, DC 20052 (United States); Kaganovich, I. D. [Princeton Plasma Physics Laboratory, Princeton, NJ 08543 (United States)] [Princeton Plasma Physics Laboratory, Princeton, NJ 08543 (United States); Demidov, V. I. [West Virginia University, Morgantown, WV 26506 (United States) [West Virginia University, Morgantown, WV 26506 (United States); St. Petersburg State University, St. Petersburg (Russian Federation)

    2013-10-15T23:59:59.000Z

    The electron energy distribution functions are studied in the low voltage dc discharge with a constriction, which is a diaphragm with an opening. The dc discharge glows in helium and is sustained by the electron current emitted from a heated cathode. We performed kinetic simulations of dc discharge characteristics and electron energy distribution functions for different gas pressures (0.8 Torr-4 Torr) and discharge current of 0.1 A. The results of these simulations indicate the ability to control the shape of the electron energy distribution functions by variation of the diaphragm opening radius.

  2. Nonlocal control of electron temperature in short direct current glow discharge plasma

    SciTech Connect (OSTI)

    Demidov, V. I. [Department of Optics and Spectroscopy, St. Petersburg State University, St. Petersburg 199034 (Russian Federation); International Laboratory “Nonlocal Plasma in Nanotechnology and Medicine”, ITMO University, Kronverkskiy pr. 49, St. Petersburg 197101 (Russian Federation); Department of Physics and Astronomy, West Virginia University, Morgantown, West Virginia 26506 (United States); Kudryavtsev, A. A.; Stepanova, O. M. [Department of Optics and Spectroscopy, St. Petersburg State University, St. Petersburg 199034 (Russian Federation); Kurlyandskaya, I. P. [International Laboratory “Nonlocal Plasma in Nanotechnology and Medicine”, ITMO University, Kronverkskiy pr. 49, St. Petersburg 197101 (Russian Federation); St. Petersburg University of State Fire Service of EMERCOM RF, Murmansk Branch, Murmansk 183040 (Russian Federation)

    2014-09-15T23:59:59.000Z

    To demonstrate controlling the electron temperature in nonlocal plasma, experiments have been performed on a short (without positive column) dc glow discharge with a cold cathode by applying different voltages to the conducting discharge wall. The experiments have been performed for low-pressure noble gas discharges. The applied voltage can modify trapping the energetic electrons emitted from the cathode sheath and arising from the atomic and molecular processes in the plasma within the device volume. This phenomenon results in the energetic electrons heating the slow plasma electrons, which consequently modifies the electron temperature. Furthermore, a numerical model of the discharge has demonstrated the electron temperature modification for the above case.

  3. E-Print Network 3.0 - assisted discharge inductive Sample Search...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    studies Summary: words: capacity fade, interfacial impedance, lithium ion batterysupercapacitor hybrid, pulse discharge... supercapacitor hybrid and a battery alone has been...

  4. Medication Adherence and Health Care Utilization among Schizophrenia Inpatients after Discharged: A Cohort Study in Taiwan.

    E-Print Network [OSTI]

    Lin, Pei-Yu

    2015-01-01T23:59:59.000Z

    ??Purpose: This study investigate the relationship and factors between medication adherence and health care utilization among Schizophrenia inpatients after discharged, for reducing relapse rate, helping… (more)

  5. Quantitative Measurements of X-ray Intensity

    SciTech Connect (OSTI)

    Haugh, M. J., Schneider, M.

    2011-09-01T23:59:59.000Z

    This chapter describes the characterization of several X-ray sources and their use in calibrating different types of X-ray cameras at National Security Technologies, LLC (NSTec). The cameras are employed in experimental plasma studies at Lawrence Livermore National Laboratory (LLNL), including the National Ignition Facility (NIF). The sources provide X-rays in the energy range from several hundred eV to 110 keV. The key to this effort is measuring the X-ray beam intensity accurately and traceable to international standards. This is accomplished using photodiodes of several types that are calibrated using radioactive sources and a synchrotron source using methods and materials that are traceable to the U.S. National Institute of Standards and Technology (NIST). The accreditation procedures are described. The chapter begins with an introduction to the fundamental concepts of X-ray physics. The types of X-ray sources that are used for device calibration are described. The next section describes the photodiode types that are used for measuring X-ray intensity: power measuring photodiodes, energy dispersive photodiodes, and cameras comprising photodiodes as pixel elements. Following their description, the methods used to calibrate the primary detectors, the power measuring photodiodes and the energy dispersive photodiodes, as well as the method used to get traceability to international standards are described. The X-ray source beams can then be measured using the primary detectors. The final section then describes the use of the calibrated X-ray beams to calibrate X-ray cameras. Many of the references are web sites that provide databases, explanations of the data and how it was generated, and data calculations for specific cases. Several general reference books related to the major topics are included. Papers expanding some subjects are cited.

  6. System and method that suppresses intensity fluctuations for free space high-speed optical communication

    DOE Patents [OSTI]

    Berman, Gennady P. (Los Alamos, NM); Bishop, Alan R. (Los Alamos, NM); Nguyen, Dinh C. (Los Alamos, NM); Chernobrod, Boris M. (Santa Fe, NM); Gorshkov, Vacheslav N. (Kiev, UA)

    2009-10-13T23:59:59.000Z

    A high-speed (Gbps), free space optical communication system is based on spectral encoding of radiation from a wide band light source, such as a laser. By using partially coherent laser beams in combination with a relatively slow photosensor, scintillations can be suppressed by orders of magnitude for distances of more than 10 km. To suppress the intensity fluctuations due to atmospheric turbulence, a source with partial transverse coherence in combination with slow response time photodetector is used. Information is encoded in the spectral domain of a wideband optical source by modulation of spectral amplitudes. A non-coherent light source with wide spectrum (an LED, for example) may be used for high-speed communication over short (less than about a mile) distances.

  7. Micro Electro Discharge Machining of Electrically Nonconductive Ceramics

    SciTech Connect (OSTI)

    Schubert, A. [Chair Micromanufacturing Technology, Faculty of Mechanical Engineering, Chemnitz University of Technology, 09107 Chemnitz (Germany); Fraunhofer Institute for Machine Tools and Forming Technology IWU, 09126 Chemnitz (Germany); Zeidler, H.; Hackert, M. [Chair Micromanufacturing Technology, Faculty of Mechanical Engineering, Chemnitz University of Technology, 09107 Chemnitz (Germany); Wolf, N. [Fraunhofer Institute for Machine Tools and Forming Technology IWU, 09126 Chemnitz (Germany)

    2011-05-04T23:59:59.000Z

    EDM is a known process for machining of hard and brittle materials. Due to its noncontact and nearly forceless behaviour, it has been introduced into micro manufacturing and through constant development it is now an important means for producing high-precision micro geometries. One restriction of EDM is its limitation to electrically conducting materials.Today many applications, especially in the biomedical field, make use of the benefits of ceramic materials, such as high strength, very low wear and biocompatibility. Common ceramic materials such as Zirconium dioxide are, due to their hardness in the sintered state, difficult to machine with conventional cutting techniques. A demand for the introduction of EDM to these materials could so far not be satisfied because of their nonconductive nature.At the Chemnitz University of Technology and the Fraunhofer IWU, investigations in the applicability of micro-EDM for the machining of nonconductive ceramics are being conducted. Tests are undertaken using micro-EDM drilling with Tungsten carbide tool electrodes and ZrO{sub 2} ceramic workpieces. A starting layer, in literature often referred to as 'assisting electrode' is used to set up a closed electric circuit to start the EDM process. Combining carbon hydride based dielectric and a specially designed low-frequency vibration setup to excite the workpiece, the process environment can be held within parameters to allow for a constant EDM process even after the starting layer is machined. In the experiments a cylindrical 120 {mu}m diameter Tungsten carbide tool electrode and Y{sub 2}O{sub 3}- and MgO- stabilized ZrO{sub 2} worpieces are used. The current and voltage signals of the discharges within the different stages of the process (machining of the starting layer, machining of the base material, transition stage) are recorded and their characteristics compared to discharges in metallic material. Additionally, the electrode feed is monitored. The influences of the process parameters are analysed with regard to the discharge type, electrode wear and process speed.Using the found parameters, micro geometries can be successfully machined into nonconductive Y{sub 2}O{sub 3}- and MgO- stabilized ZrO{sub 2} ceramic by means of micro-EDM.

  8. Energy Savings Estimates of Light Emitting Diodes in Niche Lighting...

    Office of Environmental Management (EM)

    in Niche Lighting Applications Prepared for: Building Technologies Program Office of Energy Efficiency and Renewable Energy U.S. Department of Energy Prepared by: Navigant...

  9. Light modulating device

    DOE Patents [OSTI]

    Rauh, R. David (Newton, MA); Goldner, Ronald B. (Lexington, MA)

    1989-01-01T23:59:59.000Z

    In a device for transmitting light, means for controlling the transmissivity of the device, including a ceramic, reversibly electrochromic, crystalline element having a highly reflective state when injected with electrons and charge compensating ions and a highly transmissive state when the electrons and ions are removed, the crystalline element being characterized as having a reflectivity of at least 50% in the reflective state and not greater than 10% in the transmissive state, and means for modulating the crystalline element between the reflective and transmissive states by injecting ions into the crystalline element in response to an applied electrical current of a first polarity and removing the ions in response to an applied electrical current of a second polarity.

  10. Light modulating device

    DOE Patents [OSTI]

    Rauh, R.D.; Goldner, R.B.

    1989-12-26T23:59:59.000Z

    In a device for transmitting light, means for controlling the transmissivity of the device, including a ceramic, reversibly electrochromic, crystalline element having a highly reflective state when injected with electrons and charge compensating ions and a highly transmissive state when the electrons and ions are removed, the crystalline element being characterized as having a reflectivity of at least 50% in the reflective state and not greater than 10% in the transmissive state, and means for modulating the crystalline element between the reflective and transmissive states by injecting ions into the crystalline element in response to an applied electrical current of a first polarity and removing the ions in response to an applied electrical current of a second polarity are disclosed. 1 fig.

  11. Energy and lighting

    SciTech Connect (OSTI)

    Berman, S.

    1985-01-01T23:59:59.000Z

    Advances in research for new types of lighting with increased efficacies (lumens/watt) are discussed in the following areas: (1) high-frequency, solid-state ballasts, (2) isotopic enhancement of mercury isotopes, (3) magnetic augmentation, (4) electrodeless, ultra-high frequency, (5) tuned phosphors, (6) two-photon phosphors, (7) heat mirrors, and (3) advanced control circuits to take advantage of daylight and occupancy. As of 1985, improvements in efficacy have been accomplished on an economic basis to save energy for (1) high-frequency ballasts (25%), (2) isotopic enhancement (5%), and (8) advanced control circuits (up to 50%). Most of these advances depend on a deeper understanding of the weakly ionized plasma as a radiating and diffusing medium. 3 figures, 4 tables.

  12. Cost effective lighting

    SciTech Connect (OSTI)

    Morse, O.; Verderber, R.

    1987-07-01T23:59:59.000Z

    Long-life replacement lamps for the incandescent lamp have been evaluated with regard to their cost effectiveness. The replacements include the use of energy buttons that extend lamp life as well as an adaptive fluorescent circline lamp that will fit into existing incandescent lamp sockets. The initial, operating, and replacement costs for one million lumen-hours are determined for each lamp system. We find the most important lighting cost component is the operating cost. Using lamps that are less efficient or devices that cause lamps to operate less efficiently are not cost-effective. The adaptive fluorescent circline lamp, even at an initial cost of $15.00, is the most cost effective source of illumination compared to the incandescent lamp and lamp systems examined. 3 refs., 6 tabs.

  13. Multiparameter Intelligent Monitoring in Intensive Care Ii (Mimic-Ii): A Public-Access Intensive Care Unit Database

    E-Print Network [OSTI]

    Saeed, Mohammed

    Objective: We sought to develop an intensive care unit research database applying automated techniques to aggregate high-resolution diagnostic and therapeutic data from a large, diverse population of adult intensive care ...

  14. Posters | Posters --721 Exploring lighting cultures

    E-Print Network [OSTI]

    Boyer, Edmond

    Posters | Posters -- 721 Exploring lighting cultures Beyond light and emotions Vincent LAGANIER 1 , Jasmine van der POL 2 1. Lighting Applications Services (LiAS), Philips Lighting, France vincent.laganier@philips.com 2

  15. Creative and Constructive Play with Light

    E-Print Network [OSTI]

    children identify objects with these properties. Predict what materials light will pass through. Use paint and mixing light. Mixing paint creates a muddy brown or black. Mixing light creates white light

  16. Light emission during fracture of a ZrTiNiCuBe bulk metallic glass C. J. Gilbert, J. W. Ager III, V. Schroeder, and R. O. Ritchiea)

    E-Print Network [OSTI]

    Ritchie, Robert

    -based amorphous alloys emit intense flashes of visible light when ruptured. The mechanisms for this surprising emission in air is associated with pyrolysis of fresh material exposed during rupture. © 1999 American

  17. Embodied Energy and Off-Grid Lighting

    E-Print Network [OSTI]

    Alstone, Peter

    2012-01-01T23:59:59.000Z

    as a point of comparison with LED lighting product embodieda fairer comparison between off- grid LED lighting and other

  18. Overcoming Common Pitfalls: Energy Efficient Lighting Projects...

    Broader source: Energy.gov (indexed) [DOE]

    Overcoming Common Pitfalls: Energy Efficient Lighting Projects Overcoming Common Pitfalls: Energy Efficient Lighting Projects Transcript Presentation More Documents & Publications...

  19. Automatic Mechetronic Wheel Light Device

    DOE Patents [OSTI]

    Khan, Mohammed John Fitzgerald (Silver Spring, MD)

    2004-09-14T23:59:59.000Z

    A wheel lighting device for illuminating a wheel of a vehicle to increase safety and enhance aesthetics. The device produces the appearance of a "ring of light" on a vehicle's wheels as the vehicle moves. The "ring of light" can automatically change in color and/or brightness according to a vehicle's speed, acceleration, jerk, selection of transmission gears, and/or engine speed. The device provides auxiliary indicator lights by producing light in conjunction with a vehicle's turn signals, hazard lights, alarm systems, and etc. The device comprises a combination of mechanical and electronic components and can be placed on the outer or inner surface of a wheel or made integral to a wheel or wheel cover. The device can be configured for all vehicle types, and is electrically powered by a vehicle's electrical system and/or battery.

  20. Relativistic nonlinear dynamics of an intense laser beam propagating in a hot electron-positron magnetoactive plasma

    SciTech Connect (OSTI)

    Sepehri Javan, N.; Adli, F. [Department of Physics, Faculty of Sciences, University of Mohaghegh Ardabili, P.O. Box 179, Ardabil 56199-11367 (Iran, Islamic Republic of)] [Department of Physics, Faculty of Sciences, University of Mohaghegh Ardabili, P.O. Box 179, Ardabil 56199-11367 (Iran, Islamic Republic of)

    2013-06-15T23:59:59.000Z

    The present study is devoted to investigation of the nonlinear dynamics of an intense laser beam interacting with a hot magnetized electron-positron plasma. Propagation of the intense circularly polarized laser beam along an external magnetic field is studied using a relativistic two-fluid model. A modified nonlinear Schrödinger equation is derived based on the quasi-neutral approximation, which is valid for hot plasma. Light envelope solitary waves and modulation instability are studied, for one-dimensional case. Using a three-dimensional model, spatial-temporal development of laser pulse is investigated. Occurrence of some nonlinear phenomena such as self-focusing, self-modulation, light trapping, and filamentation of laser pulse is discussed. Also the effect of external magnetic field and plasma temperature on the nonlinear evolution of these phenomena is studied.