Sample records for innovative compact design

  1. Two Piece Compaction Die Design

    SciTech Connect (OSTI)

    Coffey, Ethan N [ORNL

    2010-03-01T23:59:59.000Z

    Compaction dies used to create europium oxide and tantalum control plates were modeled using ANSYS 11.0. Two-piece designs were considered in order to make the dies easier to assemble than the five-piece dies that were previously used. The two areas of concern were the stresses at the interior corner of the die cavity and the distortion of the cavity wall due to the interference fit between the two pieces and the pressure exerted on the die during the compaction process. A successful die design would have stresses less than the yield stress of the material and a maximum wall distortion on the order of 0.0001 in. Design factors that were investigated include the inner corner radius, the value of the interference fit, the compaction force, the size of the cavity, and the outer radius and geometry of the outer ring. The results show that for the europium oxide die, a 0.01 in. diameter wire can be used to create the cavity, leading to a 0.0055 in. radius corner, if the radial interference fit is 0.003 in. For the tantalum die, the same wire can be used with a radial interference fit of 0.001 in. Also, for the europium oxide die with a 0.003 in. interference fit, it is possible to use a wire with a diameter of 0.006 in. for the wire burning process. Adding a 10% safety factor to the compaction force tends to lead to conservative estimates of the stresses but not for the wall distortion. However, when the 10% safety factor is removed, the wall distortion is not affected enough to discard the design. Finally, regarding the europium oxide die, when the cavity walls are increased by 0.002 in. per side or the outer ring is made to the same geometry as the tantalum die, all the stresses and wall distortions are within the desired range. Thus, the recommendation is to use a 0.006 in. diameter wire and a 0.003 in. interference fit for the europium oxide die and a 0.01 in. diameter wire and a 0.001 in. interference fit for the tantalum die. The dies can also be made to have the same outer geometry if desired.

  2. Spacing innovation and learning in design organizations

    E-Print Network [OSTI]

    García Herrera, Cristóbal, 1974-

    2004-01-01T23:59:59.000Z

    The main research question of this thesis is the following: What is the relationship between spaces and innovation in the context of design organizations such as IDEO, the MIT Media Lab and Design Continuum? This thesis ...

  3. Final Report for "Compact Crab Cavity Design"

    SciTech Connect (OSTI)

    Smithe, David N

    2012-11-08T23:59:59.000Z

    The goal of this project is to provide an innovative, new crab cavity design relevant to the MEIC. Through this work, we will provide comprehensive modeling of this new cavity design, including electromagnetic, thermal, and microphonic effects. One most likely candidate configuration is the design put forward by JLab and Lancaster University, UK, researchers known as the four-rod configuration. In the Phase I, Tech-X Corporation researchers performed analysis and design optimization and iteration, utilizing their state-of-the art time-domain particle-in-cell software, on a 400 MHz design for the LHC by JLab and Lancaster University, UK, researchers known as the four-rod design.

  4. Innovative Design The innovative design competition is prepared entirely outside the realm of the Western

    E-Print Network [OSTI]

    Saskatchewan, University of

    , including 3 hours during judging periods. Judging periods are to be indicated during the competitionInnovative Design The innovative design competition is prepared entirely outside the realm of the Western Engineering Competition. Competitors choose their own topic, prepare research and develop a design

  5. Designing a National Network for Manufacturing Innovation

    E-Print Network [OSTI]

    Designing a National Network for Manufacturing Innovation NNMI and The Additive Manufacturing Pilot Introduction · NNMI principles · Public NMMI Design · Pilot Institute on Additive Manufacturing #12;IMI Mission Process, such as Additive Manufacturing An Advanced Material ­ e.g. lightweight, low cost carbon fiber

  6. Integrated Scenario-based Design Methodology for Collaborative Technology Innovation

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Integrated Scenario-based Design Methodology for Collaborative Technology Innovation Fabrice Forest information technology innovation with an end-to-end Human and Social Sciences assistance. This methodology Technological innovation often requires large scale collaborative partnership between many heterogeneous

  7. Cooperative innovation in the commons : rethinking distributed collaboration and intellectual property for sustainable design innovation

    E-Print Network [OSTI]

    Sawhney, Nitin, 1971-

    2003-01-01T23:59:59.000Z

    Addressing global design challenges in the environment and underserved communities requires a cooperative approach towards sustainable design innovation, one that embraces multidisciplinary expertise, participatory design ...

  8. London 2012 Infrastructure Design, Sustainability and Innovation,

    E-Print Network [OSTI]

    Painter, Kevin

    February 2013 #12;#12;London 2012 Aspiration of a Sustainable Games #12;#12;Project Management , for both soil and groundwater treatment. As part of this work, we have managed the excavation and reuseLondon 2012 Infrastructure Design, Sustainability and Innovation, Inspiring an Industry

  9. Compact Orthogonal NMR Field Sensor - Energy Innovation Portal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power Administration would like submit the followingth Lomonosov1 COMMUNITYGeothermalCompact

  10. Use of advanced composite materials for innovative building design solutions/

    E-Print Network [OSTI]

    Lau, Tak-bun, Denvid

    2009-01-01T23:59:59.000Z

    Advanced composite materials become popular in construction industry for the innovative building design solutions including strengthening and retrofitting of existing structures. The interface between different materials ...

  11. Understanding Innovation in Student Design Projects

    E-Print Network [OSTI]

    Elizondo, Luis A.

    Over the past few years, academic institutions have become aware of the importance of innovation in education, as well as its broader role in strengthening the economy. Creativity and innovative thinking are not easily ...

  12. Southern Regional Center for Lightweight Innovative Design

    SciTech Connect (OSTI)

    None

    2012-08-24T23:59:59.000Z

    The Southern Regional Center for Lightweight Innovative Design (SRCLID) has developed an experimentally validated cradle-to-grave modeling and simulation effort to optimize automotive components in order to decrease weight and cost, yet increase performance and safety in crash scenarios. In summary, the three major objectives of this project are accomplished: To develop experimentally validated cradle-to-grave modeling and simulation tools to optimize automotive and truck components for lightweighting materials (aluminum, steel, and Mg alloys and polymer-based composites) with consideration of uncertainty to decrease weight and cost, yet increase the performance and safety in impact scenarios; To develop multiscale computational models that quantify microstructure-property relations by evaluating various length scales, from the atomic through component levels, for each step of the manufacturing process for vehicles; and To develop an integrated K-12 educational program to educate students on lightweighting designs and impact scenarios. In this final report, we divided the content into two parts: the first part contains the development of building blocks for the project, including materials and process models, process-structure-property (PSP) relationship, and experimental validation capabilities; the second part presents the demonstration task for Mg front-end work associated with USAMP projects.

  13. Options Study Documenting the Fast Reactor Fuels Innovative Design Activity

    SciTech Connect (OSTI)

    Jon Carmack; Kemal Pasamehmetoglu

    2010-07-01T23:59:59.000Z

    This document provides presentation and general analysis of innovative design concepts submitted to the FCRD Advanced Fuels Campaign by nine national laboratory teams as part of the Innovative Transmutation Fuels Concepts Call for Proposals issued on October 15, 2009 (Appendix A). Twenty one whitepapers were received and evaluated by an independent technical review committee.

  14. Military housing privatization & the promise of design innovation

    E-Print Network [OSTI]

    Ellis, Jason (Jason Robert)

    2009-01-01T23:59:59.000Z

    The objective of this paper is to answer the question, "Has the military housing privatization process produced design innovation?" Secondary questions are, "What specific role has the Army's Residential Communities ...

  15. Contestational design : innovation for political activism

    E-Print Network [OSTI]

    Hirsch, Edward A., 1970-

    2008-01-01T23:59:59.000Z

    This thesis presents contestational design, a unique form of design activity whose aim is promote particular agendas in contested political arenas. I propose a framework for analyzing contestational design processes, which ...

  16. innovati nWind Turbine Design Innovations Drive Industry Transformation

    E-Print Network [OSTI]

    innovati nWind Turbine Design Innovations Drive Industry Transformation For more than 20 years. Tackling Turbine Blade Inefficiencies In 1984, NREL researchers began investigating problems with wind turbine blade designs. Inefficiency was a significant barrier to lowering the cost of wind energy

  17. Solar optical materials for innovative window design

    SciTech Connect (OSTI)

    Lampert, C.M.

    1982-08-01T23:59:59.000Z

    New and innovative optical materials and coatings can greatly improve the efficiency of window energy systems. These potential materials and coatings increase energy efficiency by reducing radiative losses in the infrared, or reducing visible reflection losses or controlling overheating due to solar gain. Current progress in heat mirror coatings for glass and polymeric substrates is presented. Highly doped semiconducting oxides and metal/dielectric interference coatings are reviewed. Physical and optical properties are outlined for antireflection films and transparent aerogel insulation media. The potential for optical switching films as window elements includes discussions of electrochromic, photochromic and other physical switching processes.

  18. DESIGN AND INNOVATION Mns J. Molin

    E-Print Network [OSTI]

    lamps based on LED technology ­ to investigate how this integration of design at an early and Louis Paulsen set forth; to create a couple of lamps that where designed around the LED. Louis Paulsen-orthodox organization in that it included a co-operation between a research institute (Risø, at DTU) and a lamp design

  19. Innovation

    Broader source: Energy.gov (indexed) [DOE]

    At Our Disposal Open Innovation Data Liquidity FBI SCARS & TATTOOS APP Innovation Ecosystem Building Capacity A Final Word Well, three actually . . . . Open Innovation Creating...

  20. The Innovation Shop Where students conceive, design,

    E-Print Network [OSTI]

    Mountziaris, T. J.

    , forces, energy and people ­ the world of mechanical and industrial engineers. Today's engineering generation of engineers College of Engineering Mechanical and Industrial Engineering Department "Engineers mechanical and industrial engineering projects ­ including all their design, modeling, manufacturing

  1. Design of Innovative Thermoset Shape Memory Polyurethanes (SMPUs)

    E-Print Network [OSTI]

    Dalang, Robert C.

    Design of Innovative Thermoset Shape Memory Polyurethanes (SMPUs) Author: Yaobo Ding Supervisor, École Polytechnique Fédérale de Lausanne Email: yaobo.ding@epfl.ch Motivation Shape memory polymers-based shape memory polymers, and microfludic devices is one of them. Low cost SMPUs for microfluidics

  2. INNOVATION IN SERVICES: THE CONTRIBUTIONS OF DESIGN THEORY

    E-Print Network [OSTI]

    Boyer, Edmond

    INNOVATION IN SERVICES: THE CONTRIBUTIONS OF DESIGN THEORY Sylvain LENFLE University of Cergy Technologies (ICTs) has a profound impact on service activities [7-9]. This is all the more true given who made a significant contribution to the formulation of the ideas and concepts that we will develop

  3. ISTANBUL TECHNICAL UNIVERSITY INSTITUTE OF SCIENCE AND TECHNOLOGY NEW USER-CENTERED METHODS FOR DESIGN INNOVATION

    E-Print Network [OSTI]

    Mutlu, Bilge

    ISTANBUL TECHNICAL UNIVERSITY INSTITUTE OF SCIENCE AND TECHNOLOGY NEW USER-CENTERED METHODS FOR DESIGN INNOVATION: A STUDY ON THE ROLE OF EMERGING METHODS IN INNOVATIVE PRODUCT DESIGN AND DEVELOPMENT M of the 'Innovation' Concept 16 3.2. The Theory of Innovation: A Historical and Theoretical Overview 17 3

  4. Innovative Mechanical Designs in the Sierras

    E-Print Network [OSTI]

    Schladow, S. Geoffrey

    of a cooling tower, and heat recovery from a cogeneration plant. Ventilation Requirements Decoupled from Heating and Cooling Loads In any laboratory design, the first priority is proper ventilation. To meet, greatly increasing energy consumption. By decoupling sensible heating and cooling from the ventilation

  5. Design of a compact, lightweight, and low-cost solar concentrator

    E-Print Network [OSTI]

    González, Gabriel J. (Gabriel Joe), 1980-

    2004-01-01T23:59:59.000Z

    The objective of this mechanical design project was to improve the current design of large and heavy solar concentrators. The three main design goals were: making the system compact, making the system lightweight, and ...

  6. Southern Regional Center for Lightweight Innovative Design

    SciTech Connect (OSTI)

    None

    2011-10-01T23:59:59.000Z

    The three major objectives of this Phase III project are: â?¢ To develop experimentally validated cradle-to-grave modeling and simulation tools to optimize automotive and truck components for lightweighting materials (aluminum, steel, and Mg alloys and polymer-based composites) with consideration of uncertainty to decrease weight and cost, yet increase the performance and safety in impact scenarios; â?¢ To develop multiscale computational models that quantify microstructure-property relations by evaluating various length scales, from the atomic through component levels, for each step of the manufacturing process for vehicles; and â?¢ To develop an integrated K-12 educational program to educate students on lightweighting designs and impact scenarios.

  7. Innovative Design of New Geothermal Generating Plants

    SciTech Connect (OSTI)

    Bloomquist, R. Gordon; Geyer, John D.; Sifford, B. Alexander III

    1989-07-01T23:59:59.000Z

    This very significant and useful report assessed state-of-the-art geothermal technologies. The findings presented in this report are the result of site visits and interviews with plant owners and operators, representatives of major financial institutions, utilities involved with geothermal power purchases and/or wheeling. Information so obtained was supported by literature research and data supplied by engineering firms who have been involved with designing and/or construction of a majority of the plants visited. The interviews were conducted by representatives of the Bonneville Power Administration, the Washington State Energy Office, and the Oregon Department of Energy during the period 1986-1989. [DJE-2005

  8. Design Innovation Global network of designers, engineers, and innovators challenging complex real world problems

    E-Print Network [OSTI]

    Prinz, Friedrich B.

    and eight different countries. The course is now focused on teaching students the innovation methods multiple times, not only does it maximize student learning, it maximizes project insights for the student engineering students with real world engineering challenges, the course has evolved over the ages to meet

  9. Innovative Liquid Breeder Blanket Design Activities in Japan

    SciTech Connect (OSTI)

    Sagara, Akio [National Institute for Fusion Science (Japan); Tanaka, Teruya [National Institute for Fusion Science (Japan); Muroga, Takeo [National Institute for Fusion Science (Japan); Hashizume, Hidetoshi [Tohoku University (Japan); Kunugi, Tomoaki [Kyoto University (Japan); Fukada, Satoshi [Kyushu University (Japan); Shimizu, Akihiko [Kyushu University (Japan)

    2005-04-15T23:59:59.000Z

    In order to clarify key engineering issues and to enhance key R and D activities for D-T fusion blankets, many design activities on innovative liquid blanket systems are on going as collaboration studies in Japan. Recently an improved long-life Flibe blanket has been proposed, and the self-cooled Li/V blanket design has started. For Flibe systems, much progress has been made on tritium permeation barrier, energy conversion system, free surface designs, and thermofluid loop experiments. For Li/V systems, evaluation studies have proceeded on Be-free nuclear properties and allowable crack fraction on multilayered MHD insulation coatings.

  10. The design of a compact integral medium size PWR : the CIRIS

    E-Print Network [OSTI]

    Shirvan, Koroush

    2010-01-01T23:59:59.000Z

    The International Reactor Innovative and Secure (IRIS) is an advanced medium size, modular integral light water reactor design, rated currently at 1000 MWt. IRIS design has been under development by over 20 organizations ...

  11. A study of hand tamper design for compaction of soils

    E-Print Network [OSTI]

    McDonough, Brian

    1961-01-01T23:59:59.000Z

    Determination Standard Oven Dry Method versus Frying Pan Method Grain Size Distribution Curve Centerville Sand 34 Tamper Comparison Chart: Dry Density after 200 Blows per Square Foot of Layer Dry Density versus Compactive Effort Curve on 3. 0 Inch Square... of Utah revealed that a point exists at which an ultimate density is obtained, and any further increase in compaction effort results in lower than ultimate values. Shear Stress and Beari Ca acit If the resistance in a soil is exceeded by applied loads...

  12. Design of compact intermediate heat exchangers for gas cooled fast reactors

    E-Print Network [OSTI]

    Gezelius, Knut, 1978-

    2004-01-01T23:59:59.000Z

    Two aspects of an intermediate heat exchanger (IHX) for GFR service have been investigated: (1) the intrinsic characteristics of the proposed compact printed circuit heat exchanger (PCHE); and (2) a specific design optimizing ...

  13. Proceedings of 2008 NSF Engineering Research and Innovation Conference, Knoxville, Tennessee Grant # CMMI-0423485 Multiscale Design of Functionally Graded Materials

    E-Print Network [OSTI]

    Vel, Senthil

    Proceedings of 2008 NSF Engineering Research and Innovation Conference, Knoxville, Tennessee Grant: Engineering Design #12;Proceedings of 2008 NSF Engineering Research and Innovation Conference, Knoxville

  14. Compact Refractive Imaging Spectrometer Designs Utilizing Immersed Gratings

    DOE Patents [OSTI]

    Lerner, Scott A. (Livermore, CA); Bennett, Charles L. (Livermore, CA); Bixler, Jay V. (Oakland, CA); Kuzmenko, Paul J. (Livermore, CA); Lewis, Isabella T. (San Jose, CA)

    2005-07-26T23:59:59.000Z

    A compact imaging spectrometer comprising an entrance slit for directing light, a first means for receiving the light and focusing the light, an immersed diffraction grating that receives the light from the first means and defracts the light, a second means for receiving the light from the immersed diffraction grating and focusing the light, and an image plane that receives the light from the second means

  15. An Innovative Strategy for Dual Inhibitor Design and Its Application in Dual Inhibition of Human Thymidylate

    E-Print Network [OSTI]

    Lee, Keun Woo

    An Innovative Strategy for Dual Inhibitor Design and Its Application in Dual Inhibition of Human (SSAC), Plant Molecular Biology and Biotechnology Research Center (PMBBRC), Research Institute to other dual target drug designs. Citation: Arooj M, Sakkiah S, Cao Gp, Lee KW (2013) An Innovative

  16. Modular Dual Coolant Pb-17Li Blanket Design For ARIES-CS Compact Stellarator Power Plant

    E-Print Network [OSTI]

    Raffray, A. René

    of the study. The preferred blanket concept is a dual coolant blanket with a He- cooled ferritic steel firstModular Dual Coolant Pb-17Li Blanket Design For ARIES-CS Compact Stellarator Power Plant X.R. Wanga from the engineering effort during the second phase of ARIES-CS study on the conceptual design

  17. An innovative demonstration of high power density in a compact MHD (magnetohydrodynamic) generator

    SciTech Connect (OSTI)

    Schmidt, H.J.; Lineberry, J.T.; Chapman, J.N.

    1990-06-01T23:59:59.000Z

    The present program was conducted by the University of Tennessee Space Institute (UTSI). It was by its nature a high risk experimental program to demonstrate the feasibility of high power density operation in a laboratory scale combustion driven MHD generator. Maximization of specific energy was not a consideration for the present program, but the results have implications in this regard by virtue of high energy fuel used. The power density is the ratio of the electrical energy output to the internal volume of the generator channel. The MHD process is a volumetric process and the power density is therefore a direct measure of the compactness of the system. Specific energy, is the ratio of the electrical energy output to consumable energy used for its production. The two parameters are conceptually interrelated. To achieve high power density and implied commensurate low system volume and weight, it was necessary to use an energetic fuel. The high energy fuel of choice was a mixture of powdered aluminum and carbon seeded with potassium carbonate and burned with gaseous oxygen. The solid fuel was burned in a hybrid combustion scheme wherein the fuel was cast within a cylindrical combustor in analogy with a solid propellant rocket motor. Experimental data is limited to gross channel output current and voltage, magnetic field strength, fuel and oxidizer flow rates, flow train external temperatures and combustor pressure. Similarly, while instantaneous oxidizer flow rates were measured, only average fuel consumption based on pre and post test component weights and dimensions was possible. 4 refs., 60 figs., 9 tabs.

  18. Investigation of conductor swinging by wind and its application for design of compact transmission line

    SciTech Connect (OSTI)

    Tsujimoto, K.; Fujii, K.; Kubokawa, H.; Okomura, T.; Simojima, K.; Yoshioka, V.

    1982-11-01T23:59:59.000Z

    In Japan it has recently become necessary to shorten the interphase spacing in overhead transmission lines because of land limitations and economical considerations. In this connection, the authors have attempted to analyze, in-depth, the possibilities of shortened interphase spacing via conductor swinging caused by wind effects: one of the important factors in the design of more compact overhead lines. This paper describes not only the investigative results of conductor swinging that were obtained both through computer simulation and in 3 years of full scale field line testing, but also design methodology for compact overhead lines based on these results.

  19. Innovations

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of Science (SC) EnvironmentalGyroSolé(tm)HydrogenRFPTri-PartyFor manyInhibitingInnovateInnovations

  20. Innovative

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of Science (SC) EnvironmentalGyroSolé(tm)HydrogenRFPTri-PartyFor manyInhibitingInnovateInnovations

  1. Control and User Interface Design for Compact Manipulators in Minimally-Invasive Surgery

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Control and User Interface Design for Compact Manipulators in Minimally-Invasive Surgery Peter, and robust controllers. The endoscope manipulator is controlled by a single-board computer and individual Berkelman, Eric Boidard, Philippe Cinquin, Jocelyne Troccaz Abstract-- This paper describes the control

  2. Plasma engineering design of a compact reversed-field pinch reactor (CRFPR)

    SciTech Connect (OSTI)

    Bathke, C.G.; Embrechts, M.J.; Hagenson, R.L.; Krakowski, R.A.; Miller, R.L.

    1983-01-01T23:59:59.000Z

    The rationale for and the characteristics of the high-power-density Compact Reversed-Field Pinch Reactor (CRFPR) are discussed. Particular emphasis is given to key plasma engineering aspects of the conceptual design, including plasma operations, current drive, and impurity/ash control by means of pumped limiters or magnetic divertors. A brief description of the Fusion-Power-Core integration is given.

  3. Design, construction, alignment, and calibration of a compact velocimetry experiment

    SciTech Connect (OSTI)

    Kaufman, Morris I.; Malone, Robert M.; Frogget, Brent C.; Romero, Vincent T.; Esquibel, David L.; Iverson, Adam; Lare, Gregory A.; Briggs, Bart; DeVore, Douglas; Cata, Brian; McGillivray, Kevin; Palagi, Martin; et al.,

    2007-08-31T23:59:59.000Z

    A velocimetry experiment has been designed to measure shock properties for small, cylindrical, metal targets (8 mm diameter × 2 mm thick). A target is accelerated by high explosives, caught, then retrieved for later inspection. The target is expected to move at a velocity of 0.1 to 3 km/sec. The complete experiment canister is ~105 mm in diameter and 380 mm long. Optical velocimetry diagnostics include the Velocity Interferometer System for Any Reflector (VISAR) and photon Doppler velocimetry (PDV). The packaging of the velocity diagnostics is not allowed to interfere with the foam catchment or an X-ray imaging diagnostic. Using commercial lenses, a single optical relay collects Doppler-shifted light for both VISAR and PDV. The use of fiber optics allows measurement of point velocities on the target surface for accelerations lasting for 3 mm of travel. Operating at 532 nm, the VISAR has separate illumination fibers requiring alignment. The PDV diagnostic operates at 1550 nm but is aligned and calibrated at 670 nm. VISAR and PDV diagnostics are complimentary measurements that image spots in close proximity on the target surface. Because the optical relay uses commercial glass, optical fibers’ axial positions are offset to compensate for chromatic aberrations. The optomechanical design requires careful attention to fiber management, mechanical assembly and disassembly, foam catchment design, and X-ray diagnostic field of view.Calibration and alignment data are archived at each assembly sequence stage. The photon budgets for the VISAR and PDV diagnostics are separately estimated.

  4. DESIGN AND LAYOUT CONCEPTS FOR COMPACT, FACTORY-PRODUCED, TRANSPORTABLE, GENERATION IV REACTOR SYSTEMS

    SciTech Connect (OSTI)

    Mynatt Fred R.; Townsend, L.W.; Williamson, Martin; Williams, Wesley; Miller, Laurence W.; Khan, M. Khurram; McConn, Joe; Kadak, Andrew C.; Berte, Marc V.; Sawhney, Rapinder; Fife, Jacob; Sedler, Todd L.; Conway, Larry E.; Felde, Dave K.

    2003-11-12T23:59:59.000Z

    The purpose of this research project is to develop compact (100 to 400 MWe) Generation IV nuclear power plant design and layout concepts that maximize the benefits of factory-based fabrication and optimal packaging, transportation and siting. The reactor concepts selected were compact designs under development in the 2000 to 2001 period. This interdisciplinary project was comprised of three university-led nuclear engineering teams identified by reactor coolant type (water, gas, and liquid metal) and a fourth Industrial Engineering team. The reactors included a Modular Pebble Bed helium-cooled concept being developed at MIT, the IRIS water-cooled concept being developed by a team led by Westinghouse Electric Company, and a Lead-Bismuth-cooled concept developed by UT. In addition to the design and layout concepts this report includes a section on heat exchanger manufacturing simulations and a section on construction and cost impacts of proposed modular designs.

  5. Innovation

    Broader source: Energy.gov [DOE]

    In 1945, Vannevar Bush began the innovation conversation by writing Science: The Endless Frontier. In that report Bush said that "New products and new processes do not appear full-grown [they]…are painstakingly developed by research in the purest realms of science." With those words The Endless Frontier launched a national conversation linking science to the nation's manufacturing industry and thence to our country's economic prosperity and national security.

  6. Important reminders about choosing Business Design and Innovation as second major (for non-FBE students)

    E-Print Network [OSTI]

    Leung, Ka-Cheong

    Important reminders about choosing Business Design and Innovation as second major (for non-FBE selection period or add/drop period. For the successful candidates, FBE will notify students' home faculties

  7. Design, Construction, Alignment, and Calibration of a Compact Velocimetry Experiment

    SciTech Connect (OSTI)

    Kaufman, Morris I.; Malone, Robert M.; Frogget, Brent C.; Esquibel, David L.; Romero, Vincent T.; Lare, Gregory A.; Briggs, Bart; Iverson, Adam J.; Frayer, Daniel K.; DeVore, Douglas; Cata, Brian

    2007-09-21T23:59:59.000Z

    A velocimetry experiment has been designed to measure shock properties for small cylindrical metal targets (8-mm-diameter by 2-mm thick). A target is accelerated by high explosives, caught, and retrieved for later inspection. The target is expected to move at a velocity of 0.1 to 3 km/sec. The complete experiment canister is approximately 105 mm in diameter and 380 mm long. Optical velocimetry diagnostics include the Velocity Interferometer System for Any Reflector (VISAR) and Photon Doppler Velocimetry (PDV). The packaging of the velocity diagnostics is not allowed to interfere with the catchment or an X-ray imaging diagnostic. A single optical relay, using commercial lenses, collects Doppler-shifted light for both VISAR and PDV. The use of fiber optics allows measurement of point velocities on the target surface during accelerations occurring over 15 mm of travel. The VISAR operates at 532 nm and has separate illumination fibers requiring alignment. The PDV diagnostic operates at 1550 nm, but is aligned and focused at 670 nm. The VISAR and PDV diagnostics are complementary measurements and they image spots in close proximity on the target surface. Because the optical relay uses commercial glass, the axial positions of the optical fibers for PDV and VISAR are offset to compensate for chromatic aberrations. The optomechanical design requires careful attention to fiber management, mechanical assembly and disassembly, positioning of the foam catchment, and X-ray diagnostic field-of-view. Calibration and alignment data are archived at each stage of the assembly sequence.

  8. Fostering continuous innovation in design with an integrated knowledge management approach

    E-Print Network [OSTI]

    Xu, J; Caillaud, Emmanuel; Gardoni, Mickaël; 10.1016/j.compind.2010.12.005

    2012-01-01T23:59:59.000Z

    In the global competition, companies are propelled by an immense pressure to innovate. The trend to produce more new knowledge-intensive products or services and the rapid progress of information technologies arouse huge interest on knowledge management for innovation. However the strategy of knowledge management is not widely adopted for innovation in industries due to a lack of an effective approach of their integration. This study aims to help the designers to innovate more efficiently based on an integrated approach of knowledge management. Based on this integrated approach, a prototype of distributed knowledge management system for innovation is developed. An industrial application is presented and its initial results indicate the applicability of the approach and the prototype in practice.

  9. DESIGN OF A COMPACT HEAT EXCHANGER FOR HEAT RECUPERATION FROM A HIGH TEMPERATURE ELECTROLYSIS SYSTEM

    SciTech Connect (OSTI)

    G. K. Housley; J.E. O'Brien; G.L. Hawkes

    2008-11-01T23:59:59.000Z

    Design details of a compact heat exchanger and supporting hardware for heat recuperation in a high-temperature electrolysis application are presented. The recuperative heat exchanger uses a vacuum-brazed plate-fin design and operates between 300 and 800°C. It includes corrugated inserts for enhancement of heat transfer coefficients and extended heat transfer surface area. Two recuperative heat exchangers are required per each four-stack electrolysis module. The heat exchangers are mated to a base manifold unit that distributes the inlet and outlet flows to and from the four electrolysis stacks. Results of heat exchanger design calculations and assembly details are also presented.

  10. Design Options for Ultra-compact Nuclear Driven Power Sources for Field Applications

    E-Print Network [OSTI]

    Mathis, Dean

    2014-04-21T23:59:59.000Z

    Reactor LWR Light Water Reactor ? Mean Generation Time Decay Constant for Argon-41 MA Minor Actinides MCNP Monte Carlo N-Particle Transport Code Dynamic Viscosity Number Density of Argon-40 in Air Number of Fuel Elements... that are suited to these aspects separately. The Monte Carlo N-Particle transport code (MCNP) is used to design and analyze a critical, 6 controllable, compact core. Microsoft Excel is used to automate calculations using Fourier’s law of conduction2...

  11. Cost-Shared Development of Innovative Small Modular Reactor Designs |

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742Energy China U.S. DepartmentEnergy This partAsAmanda McAlpin SopAmerica Top Innovation

  12. Innovative Cell Materials and Designs for 300 Mile Range EVs

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the.pdfBreaking of BlytheDepartment ofEnergy Information forInjury andTransferInnovative

  13. Innovative Cell Materials and Designs for 300 Mile Range EVs

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(Fact Sheet),EnergyImprovementINDIANManagement1, 2010|Innovative Cell Materials

  14. Innovative Cell Materials and Designs for 300 Mile Range EVs

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(Fact Sheet),EnergyImprovementINDIANManagement1, 2010|Innovative Cell

  15. An innovative concept for deep water oil production platform design 

    E-Print Network [OSTI]

    Racine, Florian

    1994-01-01T23:59:59.000Z

    As more oil and gas are discovered in deep water, the offshore industry has become increasingly interested in the design of deep water offshore production facilities. A new design concept tentatively called FPSOT (Floating ...

  16. Design and Control of a Compact 6-Degree-of-Freedom Precision Positioner with Linux- Based Real-Time Control 

    E-Print Network [OSTI]

    Yu, Ho

    2010-01-14T23:59:59.000Z

    This dissertation presents the design, control, and implementation of a compact highprecision multidimensional positioner. This precision-positioning system consists of a novel concentrated-field magnet matrix and a ...

  17. Southern Regional Center for Lightweight Innovative Design (SRCLID...

    Broader source: Energy.gov (indexed) [DOE]

    Materials Vision: Develop multiscale physics-based material models for design optimization of components and systems made of lightweight materials in automotive applications....

  18. Southern Regional Center for Lightweight Innovative Design (SRCLID...

    Broader source: Energy.gov (indexed) [DOE]

    and experimentally validate physics-based multiscale material models for design optimization of components, systems, and lightweight materials for applications critical to the...

  19. Design, prototyping and testing of a compact superconducting double quarter wave crab cavity

    E-Print Network [OSTI]

    Xiao, Binping; Belomestnykh, Sergey; Ben-Zvi, Ilan; Calaga, Rama; Cullen, Chris; Capatina, Ofelia; Hammons, Lee; Li, Zenghai; Marques, Carlos; Skaritka, John; Verdú-Andres, Silvia; Wu, Qiong

    2015-01-01T23:59:59.000Z

    A novel design of superconducting Crab Cavity was proposed and designed at Brookhaven National Laboratory. The new cavity shape is a Double Quarter Wave or DQWCC. After fabrication and surface treatments, the niobium proof-of-principle cavity was cryogenically tested in a vertical cryostat. The cavity is extremely compact yet has a low frequency of 400 MHz, an essential property for service for the Large Hadron Collider luminosity upgrade. The electromagnetic properties of the cavity are also well matched for this demanding task. The demonstrated deflecting voltage of 4.6 MV is well above the requirement for a crab cavity in the future High Luminosity LHC of 3.34 MV. In this paper we present the design, prototyping and test results of the DQWCC.

  20. Design and initial characterization of a compact, ultra high vacuum compatible, low frequency, tilt accelerometer

    SciTech Connect (OSTI)

    O’Toole, A., E-mail: amandajotoole@gmail.com, E-mail: riccardo.desalvo@gmail.com [Department of Mechanical and Aerospace Engineering, University of California, Los Angeles, 405 Hilgard Ave, Los Angeles, California 90095 (United States); Peña Arellano, F. E. [National Astronomical Observatory of Japan, 2-21-1 Osawa, Mitaka, Tokyo 181-8588 (Japan); Rodionov, A. V.; Kim, C. [California Institute of Technology, Pasadena, California 91125 (United States); Shaner, M.; Asadoor, M. [Mayfield Senior School, 500 Bellefontaine Street Pasadena, California 91105 (United States); Sobacchi, E. [Scuola Normale Superiore, Piazza dei Cavalieri 7, 56126 Pisa (Italy); Dergachev, V.; DeSalvo, R., E-mail: amandajotoole@gmail.com, E-mail: riccardo.desalvo@gmail.com [LIGO Laboratory, California Institute of Technology, MS 100-36, Pasadena, California 91125 (United States); Bhawal, A. [Arcadia High School, 180 Campus Drive, Arcadia, California 91007 (United States); Gong, P. [Department of Precision Instrument, Tsinghua University, Beijing 100084 (China); Lottarini, A. [Department of Computer Science, University of Pisa, Largo B. Pontecorvo 3, 56127 Pisa (Italy); Minenkov, Y. [Sezione INFN Tor Vergata, via della Ricerca Scientfica 1, 00133 Roma (Italy); Murphy, C. [School of Physics, The University of Western Australia, 35 Stirling Highway, Crawley, Perth, Western Australia 6009 (Australia)

    2014-07-15T23:59:59.000Z

    A compact tilt accelerometer with high sensitivity at low frequency was designed to provide low frequency corrections for the feedback signal of the Advanced Laser Interferometer Gravitational Wave Observatory active seismic attenuation system. It has been developed using a Tungsten Carbide ceramic knife-edge hinge designed to avoid the mechanical 1/f noise believed to be intrinsic in polycrystalline metallic flexures. Design and construction details are presented; prototype data acquisition and control limitations are discussed. The instrument's characterization reported here shows that the hinge is compatible with being metal-hysteresis-free, and therefore also free of the 1/f noise generated by the dislocation Self-Organized Criticality in the metal. A tiltmeter of this kind will be effective to separate the ground tilt component from the signal of horizontal low frequency seismometers, and to correct the ill effects of microseismic tilt in advanced seismic attenuation systems.

  1. A novel compact design of calibration equipment for gas and thermal sensors

    SciTech Connect (OSTI)

    Feng, P. X.; Zhang, H. X.; Peng, X. Y.; Sajjad, M.; Chu, J. [Institute for Functional Nanomaterials and Department of Physics, University of Puerto Rico, P.O. Box 70377, San Juan, 00936-8377 (Puerto Rico)

    2011-04-15T23:59:59.000Z

    A novel design of calibration equipment has been developed for static and dynamic calibrations of gas and thermal sensors. This system is cheap, compact, and easily adjustable, which is also combined with a plasma surface modification source for tailoring the surface of sensors to ensure the sensitivity and selectivity. The main advantage of this equipment is that the operating temperature, bias voltage, types of plasma source (for surface modification), types of feeding gases, and gas flow rate (for calibrations), etc., can be independently controlled. This novel system provides a highly reliable, reproducible, and economical method of calibrations for various gas and thermal sensors.

  2. A brief history of design studies on innovative nuclear reactors

    SciTech Connect (OSTI)

    Sekimoto, Hiroshi, E-mail: hsekimot@gmail.com [Emeritus Professor, Tokyo Institute of Technology (Japan)

    2014-09-30T23:59:59.000Z

    In a short period after the success of CP1, many types of nuclear reactors were proposed and investigated. However, soon only a small number of reactors were selected for practical use. Around 1970, only LWRs with small number of CANDUs were operated in the western world, and FBRs were under development. It was about the time when Apollo moon landing was accomplished. However, at the same time, the future of human being was widely considered pessimistic and Limits to Growth was published. In the end of 1970’s the TMI accident occurred and many nuclear reactor contracts were cancelled in USA and any more contracts had not been concluded until recent years. From the reflection of this accident, many Inherent Safe Reactors (ISRs) were proposed, though none of them were constructed. A common idea of ISRs is smallness of their size. Tokyo Institute of Technology (TokyoTech) held a symposium on small reactors, SR/TIT, in 1991, where many types of small ISRs were presented. Recently small reactors attract interest again. The most ideas employed in these reactors were the same discussed in SR/TIT. In 1980’s the radioactive wastes from fuel cycle became a severe problem around the world. In TokyoTech, this issue was discussed mainly from the viewpoint of nuclear transmutations. The neutron economy became inevitable for these innovative nuclear reactors especially small long-life reactors and transmutation reactors.

  3. Innovative fuel designs for high power density pressurized water reactor

    E-Print Network [OSTI]

    Feng, Dandong, Ph. D. Massachusetts Institute of Technology

    2006-01-01T23:59:59.000Z

    One of the ways to lower the cost of nuclear energy is to increase the power density of the reactor core. Features of fuel design that enhance the potential for high power density are derived based on characteristics of ...

  4. EcoCAR by Georgia Tech efficiency through design and innovation

    E-Print Network [OSTI]

    Houston, Paul L.

    engineering competition sponsored by the Department of Energy and General Motors EcoCAR by Georgia Tech engineering competition sponsored by the Department of Energy and General Motors #12;GT EcoCAR GOALS: Increase by the Department of Energy and General Motors EcoCAR by Georgia Tech efficiency through design and innovation

  5. Fusion Engineering and Design 81 (2006) 455460 Breeder foam: an innovative low porosity solid breeder material

    E-Print Network [OSTI]

    Ghoniem, Nasr M.

    2006-01-01T23:59:59.000Z

    ; Foam processing; Foam applications 1. Introduction Solid breeder blanket concepts are typically based structural and Be material requirements in a breeder blanket. However, high density Li-ceramic foams haveFusion Engineering and Design 81 (2006) 455­460 Breeder foam: an innovative low porosity solid

  6. Innovative Feed-In Tariff Designs that Limit Policy Costs

    SciTech Connect (OSTI)

    Kreycik, C.; Couture, T. D.; Cory, K. S.

    2011-06-01T23:59:59.000Z

    Feed-in tariffs (FITs) are the most prevalent renewable energy policy used globally to date, and there are many benefits to the certainty offered in the marketplace to reduce development risks and associated financing costs and to grow the renewable energy industry. However, concerns over escalating costs in jurisdictions with FIT policies have led to increased attention on cost control in renewable energy policy design. In recent years, policy mechanisms for containing FIT costs have become more refined, allowing policymakers to exert greater control on policy outcomes and on the resulting costs to ratepayers. As policymakers and regulators in the United States begin to explore the use of FITs, careful consideration must be given to the ways in which policy design can be used to balance the policies' advantages while bounding its costs. This report explores mechanisms that policymakers have implemented to limit FIT policy costs. If designed clearly and transparently, such mechanisms can align policymaker and market expectations for project deployment. Three different policy tools are evaluated: (1) caps, (2) payment level adjustment mechanisms, and (3) auction-based designs. The report employs case studies to explore the strengths and weaknesses of these three cost containment tools. These tools are then evaluated with a set of criteria including predictability for policymakers and the marketplace and the potential for unintended consequences.

  7. A Design for a Compact Time-of-Flight Mass Spectrometer

    SciTech Connect (OSTI)

    Manard, M.

    2012-10-01T23:59:59.000Z

    The design of a prototype, compact time-of-flight (TOF) mass spectrometer (MS) is described. The system primarily consists of an ion acceleration/focusing/steering assembly (AFSA), an 8 cm field-free region, a 4 cm, dual-stage reflectron and a miniature microchannel plate detector. Consequently, the resulting flight length of the system is 12 cm. The system has been designed with the capability to sample directly from atmosphere at ambient pressures. This is accomplished through the use of an electrodynamic ion funnel, housed in an intermediate-vacuum chamber that is coupled to the inlet of the TOF chamber. TOF spectra were obtained using noble gases (Ar, Kr and Xe) as test chemicals. These measured flight times were used to probe the performance of the instrument. A temporal resolution (tflight/?t) of approximately 125, acquired using 129Xe+, has been measured for the system.

  8. Fusion Engineering and Design 82 (2007) 26962704 Engineering challenges in designing an attractive compact

    E-Print Network [OSTI]

    Najmabadi, Farrokh

    2007-01-01T23:59:59.000Z

    -CS. is a dual-coolant (He + Pb­17Li) ferritic-steel mod- ular blanket concept coupled with a Brayton power cycle plant; Engineering design 1. Introduction The ARIES-CS team is conducting the final phase of its

  9. Fusion Engineering and Design 81 (2006) 26792693 Recent progress in the ARIES compact stellarator study

    E-Print Network [OSTI]

    Najmabadi, Farrokh

    2006-01-01T23:59:59.000Z

    of compact stellarator power plants, ARIES-CS, was initiated recently to explore attractive compact are similar in size to advanced tokamak power plants. © 2006 Elsevier B.V. All rights reserved. Keywords: Fusion power plant; Compact stellarator Corresponding author. Tel.: +1 858 534 7869; fax: +1 858 822

  10. Design and Implementation of a self-calibrating, compact micro strip sensor for in-situ dielectric

    E-Print Network [OSTI]

    Kumar, Ratnesh

    sensor electrode [5], [6] has proven that multi-frequency impedance measurement of a soil mixture has MEASUREMENT Figure 1 describes the main idea behind multi-frequency impedance measurement. A signal ViDesign and Implementation of a self-calibrating, compact micro strip sensor for in-situ dielectric

  11. Thomson scattering diagnostic system design for the Compact Toroidal Hybrid experiment

    SciTech Connect (OSTI)

    Traverso, P. J., E-mail: pjt0002@auburn.edu; Maurer, D. A.; Ennis, D. A.; Hartwell, G. J.; Goforth, M. M.; Loch, S. D.; Pearce, A. J.; Cianciosa, M. R. [Physics Department, Auburn University, Auburn, Alabama 36849 (United States)

    2014-11-15T23:59:59.000Z

    A new Thomson scattering system using standard commercially available components has been designed for the non-axisymmetric plasmas of the Compact Toroidal Hybrid (CTH). The beam, generated by a frequency doubled Continuum PL DLS 2 J Nd:YAG laser, is passed vertically through an entrance Brewster window and an aperturing baffle system to minimize the stray laser light that could enter the collection optics. The beam line has been designed with an 8 m propagation distance to the mid-plane of the CTH device with the beam diameter kept less than 3 mm inside the plasma volume. The beam exits the vacuum system through another Brewster window and enters a beam dump, again to minimize the stray light in the vacuum chamber. Light collection, spectral processing, and signal detection are accomplished with an f/#? 1 aspheric lens, a commercially available Holospec f/1.8 spectrometer, and an Andor iStar DH740-18U-C3 image intensified camera. Spectral rejection of stray laser light, if needed, can be performed with the use of an optional interference filter at the spectrometer input. The system has been developed for initial single point measurements of plasmas with core electron temperatures of approximately 20–300 eV and densities of 5 × 10{sup 18} to 5 × 10{sup 19}?m{sup ?3} dependent upon operational scenario.

  12. Technology Innovation Program | Partnerships | ORNL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Innovation Program SHARE Technology Innovation Program The Technology Innovation Program (TIP) is a 1-year program designed to accelerate selected technologies to commercial...

  13. Energy master planning: Innovative Design and Energy Analysis Service (IDEAS) for new commercial construction

    SciTech Connect (OSTI)

    Not Available

    1989-11-01T23:59:59.000Z

    This report describes a research and development strategy that a municipal energy management office took to adopt and promote an energy design and analysis program for commercial building development projects. Included are details of the technical information, technology transfer tools, marketing strategies and methods of integrating the energy efficient design suggestion program into the existing city development process for maximizing the administration and effectiveness of the service. The Office of Environmental Management of the City of San Jose developed and is offering a Pilot Program aimed at improving the energy efficiency of its commercial and light industrial building stock. The proposed Innovative Design and Energy Analysis Service (IDEAS) would offer technical information and assistance to Developers, Architects and Engineers in the area of energy conscious design of new commercial construction in the City of San Jose. The main thrust of the service will be to influence new building design through the implementation of cost-effective energy conservation options such that building operational performance is better than that resulting from implementing mandated state energy standards. 21 refs., 10 figs., 6 tabs.

  14. Penetrator reliability investigation and design exploration : from conventional design processes to innovative uncertainty-capturing algorithms.

    SciTech Connect (OSTI)

    Martinez-Canales, Monica L.; Heaphy, Robert (Sandia National Laboratories, Albuquerque, NM); Gramacy, Robert B. (University of Cambridge); Taddy, Matt (University of California, Santa Cruz, CA); Chiesa, Michael L.; Thomas, Stephen W. (Sandia National Laboratories, Albuquerque, NM); Swiler, Laura Painton (Sandia National Laboratories, Albuquerque, NM); Hough, Patricia Diane; Lee, Herbert K. H. (University of California, Santa Cruz, CA); Trucano, Timothy Guy (Sandia National Laboratories, Albuquerque, NM); Gray, Genetha Anne

    2006-11-01T23:59:59.000Z

    This project focused on research and algorithmic development in optimization under uncertainty (OUU) problems driven by earth penetrator (EP) designs. While taking into account uncertainty, we addressed three challenges in current simulation-based engineering design and analysis processes. The first challenge required leveraging small local samples, already constructed by optimization algorithms, to build effective surrogate models. We used Gaussian Process (GP) models to construct these surrogates. We developed two OUU algorithms using 'local' GPs (OUU-LGP) and one OUU algorithm using 'global' GPs (OUU-GGP) that appear competitive or better than current methods. The second challenge was to develop a methodical design process based on multi-resolution, multi-fidelity models. We developed a Multi-Fidelity Bayesian Auto-regressive process (MF-BAP). The third challenge involved the development of tools that are computational feasible and accessible. We created MATLAB{reg_sign} and initial DAKOTA implementations of our algorithms.

  15. Design approach for the development of a cryomodule for compact crab cavities for Hi-Lumi LHC

    SciTech Connect (OSTI)

    Pattalwar, Shrikant; Goudket, Philippe; McIntosh, Peter; Wheelhouse, Alan [Accelerator Science and Technology Centre, STFC Daresbury Laboratory, Warrington WA44AD, UK and Cockcroft Institute, STFC Daresbury Laboratory, Warrington, WA44AD (United Kingdom); Jones, Thomas; Templeton, Niklas [Technology Group, STFC Daresbury Laboratory, Warrington, WA44A (United Kingdom); Burt, Graeme; Hall, Ben [University of Lancaster, Lancaster, UK and Cockcroft Institute, STFC Daresbury Laboratory, Warrington, WA44AD (United Kingdom); Wright, Loren [University of Lancaster, Lancaster, UK and TE-MSC-C, CERN, Geneva (Switzerland); Peterson, Tom [Technical Division, Fermilab, P.O. Box 500, Batavia, IL 60510 (United States)

    2014-01-29T23:59:59.000Z

    A prototype Superconducting RF (SRF) cryomodule, comprising multiple compact crab cavities is foreseen to realise a local crab crossing scheme for the “Hi-Lumi LHC”, a project launched by CERN to increase the luminosity performance of LHC. A cryomodule with two cavities will be initially installed and tested on the SPS drive accelerator at CERN to evaluate performance with high-intensity proton beams. A series of boundary conditions influence the design of the cryomodule prototype, arising from; the complexity of the cavity design, the requirement for multiple RF couplers, the close proximity to the second LHC beam pipe and the tight space constraints in the SPS and LHC tunnels. As a result, the design of the helium vessel and the cryomodule has become extremely challenging. This paper assesses some of the critical cryogenic and engineering design requirements and describes an optimised cryomodule solution for the evaluation tests on SPS.

  16. Design of a compact ultrahigh vacuum-compatible setup for the analysis of chemical vapor deposition processes

    SciTech Connect (OSTI)

    Weiss, Theodor; Nowak, Martin; Zielasek, Volkmar, E-mail: zielasek@uni-bremen.de; Bäumer, Marcus [Institut für Angewandte und Physikalische Chemie, Universität Bremen, Leobener Straße UFT, D-28359 Bremen (Germany); Mundloch, Udo; Kohse-Höinghaus, Katharina [Physikalische Chemie I, Fakultät für Chemie, Universität Bielefeld, Universitätsstraße 25, D-33615 Bielefeld (Germany)

    2014-10-15T23:59:59.000Z

    Optimizing thin film deposition techniques requires contamination-free transfer from the reactor into an ultrahigh vacuum (UHV) chamber for surface science analysis. A very compact, multifunctional Chemical Vapor Deposition (CVD) reactor for direct attachment to any typical UHV system for thin film analysis was designed and built. Besides compactness, fast, easy, and at the same time ultimately clean sample transfer between reactor and UHV was a major goal. It was achieved by a combination of sample manipulation parts, sample heater, and a shutter mechanism designed to fit all into a NW38 Conflat six-ways cross. The present reactor design is versatile to be employed for all commonly employed variants of CVD, including Atomic Layer Deposition. A demonstration of the functionality of the system is provided. First results of the setup (attached to an Omicron Multiprobe x-ray photoelectron spectroscopy system) on the temperature dependence of Pulsed Spray Evaporation-CVD of Ni films from Ni acetylacetonate as the precursor demonstrate the reactor performance and illustrate the importance of clean sample transfer without breaking vacuum in order to obtain unambiguous results on the quality of CVD-grown thin Ni films. The widely applicable design holds promise for future systematic studies of the fundamental processes during chemical vapor deposition or atomic layer deposition.

  17. Innovative coke oven gas cleaning system for retrofit applications. Volume 1, Public design report

    SciTech Connect (OSTI)

    Not Available

    1994-05-24T23:59:59.000Z

    This Public Design Report provides, in a single document, available nonproprietary design -information for the ``Innovative Coke Oven Gas Cleaning System for Retrofit Applications`` Demonstration Project at Bethlehem Steel Corporation`s Sparrows Point, Maryland coke oven by-product facilities. This project demonstrates, for the first time in the United States, the feasibility of integrating four commercially available technologies (processes) for cleaning coke oven gas. The four technologies are: Secondary Gas Cooling, Hydrogen Sulfide and Ammonia Removal, Hydrogen Sulfide and Ammonia Recovery, and Ammonia Destruction and Sulfur Recovery. In addition to the design aspects, the history of the project and the role of the US Department of,Energy are briefly discussed. Actual plant capital and projected operating costs are also presented. An overview of the integration (retrofit) of the processes into the existing plant is presented and is followed by detailed non-proprietary descriptions of the four technologies and their overall effect on reducing the emissions of ammonia, sulfur, and other pollutants from coke oven gas. Narrative process descriptions, simplified process flow diagrams, input/output stream data, operating conditions, catalyst and chemical requirements, and utility requirements are given for each unit. Plant startup provisions, environmental considerations and control monitoring, and safety considerations are also addressed for each process.

  18. Designing a model for the African Science and Innovation Facility to implement the Science and Technology Consolidated Plan of Action

    E-Print Network [OSTI]

    Designing a model for the African Science and Innovation Facility to implement the Science and Technology Consolidated Plan of Action A study commissioned by NEPAD's Office of Science and Technology been prepared in response to a request from NEPAD's Office of Science and Technology for a review

  19. Steps to an Ecology of Networked Knowledge and Innovation: Enabling new forms of collaboration among sciences, engineering, arts, and design

    E-Print Network [OSTI]

    Malina, Roger; Strohecker, Carol; LaFayette, Carol; Ione, Amy

    2013-07-31T23:59:59.000Z

    among scientists, engineers, artists, designers, and humanities researchers has been accelerating over the past decade. This has generated emerging practices that impact work and have potential to mitigate the difficult problems of our times... relationships 3. Forming safe, productive environments for hybrid individuals and practices INCLUDING: Spurring innovation through diversity 4. Communities addressing global issues and local solutions EMBEDDING: Public engagement and negotiation 5...

  20. Finite element analysis and design of large diameter flexible vertical pipes subjected to incremental compacted backfill loads and creep effects

    E-Print Network [OSTI]

    Hossain, Mohammad Kabir

    1990-01-01T23:59:59.000Z

    FINITE ELEMENT ANALYSIS AND DESiGN OF LARGE DIANETER FLEXIBLE VERTICAL PIPES SUBJECTED TO INCREMENTAL COMPACTED BACKFILL LOADS AND CREEP EFFECTS A Thesis by MOHAMMAD KABIR HOSSAIN Submitted to the Office of Graduate Studies of Texas A... BACKFILL LOADS AND CREEP EFFECTS A Thesis by MOHAMMAD KABIR HOSSAIN Approved as to sty1e and content by: R be+r L. Lytton (Chair of Committee) Ozden 0. Ochoa (Member) Derek V. Morris (Member) ames T P Yao (Head of rtment) ABSTRACT Finite...

  1. Demonstration of improved vehicle fuel efficiency through innovative tire design, materials, and weight reduction technologies

    SciTech Connect (OSTI)

    Donley, Tim [Cooper Tire & Rubber Company Incorporated, Findlay, OH (United States)

    2014-12-31T23:59:59.000Z

    Cooper completed an investigation into new tire technology using a novel approach to develop and demonstrate a new class of fuel efficient tires using innovative materials technology and tire design concepts. The objective of this work was to develop a new class of fuel efficient tires, focused on the “replacement market” that would improve overall passenger vehicle fuel efficiency by 3% while lowering the overall tire weight by 20%. A further goal of this project was to accomplish the objectives while maintaining the traction and wear performance of the control tire. This program was designed to build on what has already been accomplished in the tire industry for rolling resistance based on the knowledge and general principles developed over the past decades. Cooper’s CS4 (Figure #1) premium broadline tire was chosen as the control tire for this program. For Cooper to achieve the goals of this project, the development of multiple technologies was necessary. Six technologies were chosen that are not currently being used in the tire industry at any significant level, but that showed excellent prospects in preliminary research. This development was divided into two phases. Phase I investigated six different technologies as individual components. Phase II then took a holistic approach by combining all the technologies that showed positive results during phase one development.

  2. DESIGN AND DEVELOPMENT OF GAS-LIQUID CYLINDRICAL CYCLONE COMPACT SEPARATORS FOR THREE-PHASE FLOW

    SciTech Connect (OSTI)

    Dr. Ram S. Mohan; Dr. Ovadia Shoham

    2003-06-25T23:59:59.000Z

    The U.S. Department of Energy (DOE) has awarded a five-year (1997-2002) grant (Mohan and Shoham, DE-FG26-97BC15024, 1997) to The University of Tulsa, to develop compact multiphase separation components for 3-phase flow. The research activities of this project have been conducted through cost sharing by the member companies of the Tulsa University Separation Technology Projects (TUSTP) research consortium and the Oklahoma Center for the Advancement of Science and Technology (OCAST). As part of this project, several individual compact separation components have been developed for onshore and offshore applications. These include gas-liquid cylindrical cyclones (GLCC{copyright}), liquid-liquid cylindrical cyclones (LLCC{copyright}), and the gas-liquid-liquid cylindrical cyclones (GLLCC{copyright}). A detailed study has also been completed for the liquid-liquid hydrocyclones (LLHC). Appropriate control strategies have been developed for proper operation of the GLCC{copyright} and LLCC{copyright}. Testing of GLCC{copyright} at high pressure and real crude conditions for field applications is also completed. Limited studies have been conducted on flow conditioning devices to be used upstream of the compact separators for performance improvement. This report presents a brief overview of the activities and tasks accomplished during the 5-year project period, October 1, 1997-March 31, 2003 (including the no-cost extended period of 6 months). An executive summary is presented initially followed by the tasks of the 5-year budget periods. Then, detailed description of the experimental and modeling investigations are presented. Subsequently, the technical and scientific results of the activities of this project period are presented with some discussions. The findings of this investigation are summarized in the ''Conclusions'' section, followed by relevant references. The publications resulting from this study in the form of MS Theses, Ph.D. Dissertation, Journal Papers and Conference Presentations are provided at the end of this report.

  3. Cogeneration of Electricity and Potable Water Using The International Reactor Innovative And Secure (IRIS) Design

    SciTech Connect (OSTI)

    Ingersoll, D.T.; Binder, J.L.; Kostin, V.I.; Panov, Y.K.; Polunichev, V.; Ricotti, M.E.; Conti, D.; Alonso, G.

    2004-10-06T23:59:59.000Z

    The worldwide demand for potable water has been steadily growing and is projected to accelerate, driven by a continued population growth and industrialization of emerging countries. This growth is reflected in a recent market survey by the World Resources Institute, which shows a doubling in the installed capacity of seawater desalination plants every ten years. The production of desalinated water is energy intensive, requiring approximately 3-6 kWh/m3 of produced desalted water. At current U.S. water use rates, a dedicated 1000 MW power plant for every one million people would be required to meet our water needs with desalted water. Nuclear energy plants are attractive for large scale desalination application. The thermal energy produced in a nuclear plant can provide both electricity and desalted water without the production of greenhouse gases. A particularly attractive option for nuclear desalination is to couple a desalination plant with an advanced, modular, passively safe reactor design. The use of small-to-medium sized nuclear power plants allows for countries with smaller electrical grid needs and infrastructure to add new electrical and water capacity in more appropriate increments and allows countries to consider siting plants at a broader number of distributed locations. To meet these needs, a modified version of the International Reactor Innovative and Secure (IRIS) nuclear power plant design has been developed for the cogeneration of electricity and desalted water. The modular, passively safe features of IRIS make it especially well adapted for this application. Furthermore, several design features of the IRIS reactor will ensure a safe and reliable source of energy and water even for countries with limited nuclear power experience and infrastructure. The IRIS-D design utilizes low-quality steam extracted from the low-pressure turbine to boil seawater in a multi-effect distillation desalination plant. The desalination plant is based on the horizontal tube film evaporation design used successfully with the BN-350 nuclear plant in Aktau, Kazakhstan. Parametric studies have been performed to optimize the balance of plant design. Also, an economic analysis has been performed, which shows that IRIS-D should be able to provide electricity and clean water at highly competitive costs.

  4. Compact Microstrip Filter Designs and Phased Array for Multifunction Radar Applications

    E-Print Network [OSTI]

    Jung, Dong Jin

    2012-07-16T23:59:59.000Z

    This dissertation mainly discuses various microstrip bandpass filter (BPF) designs. The filter designs include: a coupled line BPF using nonuniform arbitrary image impedances, miniaturized BPF utilizing dumbbell shaped slot resonator (DSSR), BPF...

  5. Modeling and design of compact microwave components and systems for wireless communications and power transmission

    E-Print Network [OSTI]

    Zepeda, Paola

    2004-09-30T23:59:59.000Z

    The contribution of the work here presented involves three main topics: Wireless Power Transmission (WPT) technology, phased array systems, and microwave components design and modeling. The first topic presents the conceptual design of a WPT system...

  6. Design of a compact electron cyclotron resonance ion source for medium charge state light ions

    SciTech Connect (OSTI)

    Button, D.; Hotchkis, M. A. C. [Australian Nuclear Science and Technology Organization, Sydney, NSW 2234 (Australia); Milford, G. N. [University of New South Wales, Canberra, ACT 2600 (Australia)

    2012-02-15T23:59:59.000Z

    At the Australian Nuclear Science and Technology Organization we are developing a new isotope ratio mass spectrometer based on the measurement of multiple charge state ions. We have carried out a review of our existing ECR ion source and identified a number of design flaws. For the new instrument, we are producing a new ECR source and have refined the design, in particular by using 3D simulations to improve the magnetic confinement field and by a combination of simulations and experiments to improve the design of the microwave coupling.

  7. Design Optimization of Innovative High-Level Waste Pipeline Unplugging Technologies - 13341

    SciTech Connect (OSTI)

    Pribanic, T.; Awwad, A.; Varona, J.; McDaniel, D.; Gokaltun, S.; Crespo, J. [Applied Research Center, Florida International University, 10555 West Flagler Street, Suite 2100, Miami. FL 33174 (United States)] [Applied Research Center, Florida International University, 10555 West Flagler Street, Suite 2100, Miami. FL 33174 (United States)

    2013-07-01T23:59:59.000Z

    Florida International University (FIU) is currently working on the development and optimization of two innovative pipeline unplugging methods: the asynchronous pulsing system (APS) and the peristaltic crawler system (PCS). Experiments were conducted on the APS to determine how air in the pipeline influences the system's performance as well as determine the effectiveness of air mitigation techniques in a pipeline. The results obtained during the experimental phase of the project, including data from pipeline pressure pulse tests along with air bubble compression tests are presented. Single-cycle pulse amplification caused by a fast-acting cylinder piston pump in 21.8, 30.5, and 43.6 m pipelines were evaluated. Experiments were conducted on fully flooded pipelines as well as pipelines that contained various amounts of air to evaluate the system's performance when air is present in the pipeline. Also presented are details of the improvements implemented to the third generation crawler system (PCS). The improvements include the redesign of the rims of the unit to accommodate a camera system that provides visual feedback of the conditions inside the pipeline. Visual feedback allows the crawler to be used as a pipeline unplugging and inspection tool. Tests conducted previously demonstrated a significant reduction of the crawler speed with increasing length of tether. Current improvements include the positioning of a pneumatic valve manifold system that is located in close proximity to the crawler, rendering tether length independent of crawler speed. Additional improvements to increase the crawler's speed were also investigated and presented. Descriptions of the test beds, which were designed to emulate possible scenarios present on the Department of Energy (DOE) pipelines, are presented. Finally, conclusions and recommendations for the systems are provided. (authors)

  8. Design and Application of Low Compaction Energy Concrete for Use in Slip-form Concrete

    E-Print Network [OSTI]

    used were different types of clays, fly ash and magnesium oxide. The addition of polypropylene fibers Institute for TEA- 21 funded projects designated A215 DISCLAIMER: The contents of this report reflect

  9. Compact-designed supercapacitors using free-standing single-walled carbon nanotube films

    E-Print Network [OSTI]

    Wang, Wei Hua

    performance, but also small size and light weight. The super- capacitors can be of various designs including capacitors, have attracted much attention because of their high power and energy densities and long cycle

  10. Bicriteria Optimization of Technological Parameters in Compact Algorithm for Designing Soft Magnetic Composites

    E-Print Network [OSTI]

    Sokalski, Krzysztof; ?lusarek, Barbara

    2015-01-01T23:59:59.000Z

    The paper presents a novel algorithm for designing technological parameters by which one optimize power losses and induction in SMC. The advantage of the presented algorithm consists in the bicriteria optimization: minimization of losses and maximization of induction. The crucial role in the presented algotithm plays scaling.

  11. Bicriteria Optimization of Technological Parameters in Compact Algorithm for Designing Soft Magnetic Composites

    E-Print Network [OSTI]

    Krzysztof Sokalski; Bartosz Jankowski; Barbara ?lusarek

    2015-03-11T23:59:59.000Z

    The paper presents a novel algorithm for designing technological parameters by which one optimize power losses and induction in SMC. The advantage of the presented algorithm consists in the bicriteria optimization: minimization of losses and maximization of induction. The crucial role in the presented algotithm plays scaling.

  12. Innovative Structural and Joining Concepts for Lightweight Design of Heavy Vehicle Systems

    SciTech Connect (OSTI)

    Jacky C. Prucz; Samir N. Shoukry; Gergis W. William

    2005-08-31T23:59:59.000Z

    Recent advances in the area of Metal Matrix Composites (MMC's) have brought these materials to a maturity stage where the technology is ready for transition to large-volume production and commercialization. The new materials seem to allow the fabrication of higher quality parts at less than 50 percent of the weight as compared to steel, especially when they are selectively reinforced with carbon, silicon carbide, or aluminum oxide fibers. Most of the developments in the MMC materials have been spurred, mainly by applications that require high structural performance at elevated temperatures, the heavy vehicle industry could also benefit from this emerging technology. Increasing requirements of weight savings and extended durability are the main drivers for potential insertion of MMC technology into the heavy vehicle market. Critical elements of a typical tractor-trailer combination, such as highly loaded sections of the structure, engine components, brakes, suspensions, joints and bearings could be improved through judicious use of MMC materials. Such an outcome would promote the DOE's programmatic objectives of increasing the fuel efficiency of heavy vehicles and reducing their life cycle costs and pollution levels. However, significant technical and economical barriers are likely to hinder or even prevent broad applications of MMC materials in heavy vehicles. The tradeoffs between such expected benefits (lower weights and longer durability) and penalties (higher costs, brittle behavior, and difficult to machine) must be thoroughly investigated both from the performance and cost viewpoints, before the transfer of MMC technology to heavy vehicle systems can be properly assessed and implemented. MMC materials are considered to form one element of the comprehensive, multi-faceted strategy pursued by the High Strength/Weight Reduction (HS/WR) Materials program of the U.S. Department of Energy (DOE) for structural weight savings and quality enhancements in heavy vehicles. The research work planed for the first year of this project (June 1, 2003 through May 30, 2004) focused on a theoretical investigation of weight benefits and structural performance tradeoffs associated with the design, fabrication, and joining of MMC components for heavy-duty vehicles. This early research work conducted at West Virginia University yielded the development of integrated material-structural models that predicted marginal benefits and significant barriers to MMC applications in heavy trailers. The results also indicated that potential applications of MMC materials in heavy vehicles are limited to components identified as critical for either loadings or weight savings. Therefore, the scope of the project was expanded in the following year (June 1, 2004 through May 30, 2005) focused on expanding the lightweight material-structural design concepts for heavy vehicles from the component to the system level. Thus, the following objectives were set: (1) Devise and evaluate lightweight structural configurations for heavy vehicles. (2) Study the feasibility of using Metal Matrix Composites (MMC) for critical structural components and joints in heavy vehicles. (3) Develop analysis tools, methods, and validated test data for comparative assessments of innovative design and joining concepts. (4) Develop analytical models and software for durability predictions of typical heavy vehicle components made of particulate MMC or fiber-reinforced composites. This report summarizes the results of the research work conducted during the past two years in this projects.

  13. Fabrication and Design Aspects of High-Temperature Compact Diffusion Bonded Heat Exchangers

    SciTech Connect (OSTI)

    Mylavarapu, Sai K. [Ohio State University; Sun, Xiaodong [Ohio State University; Christensen, Richard N. [Ohio State University; Glosup, Richard E. [Ohio State University; Unocic, Raymond R [ORNL

    2012-01-01T23:59:59.000Z

    The very high temperature reactor (VHTR), using gas-cooled reactor technology, is one of the six reactor concepts selected by the Generation IV International Forum and is anticipated to be the reactor type for the next generation nuclear plant (NGNP). In this type of reactor with an indirect power cycle system, a high-temperature and high integrity intermediate heat exchanger (IHX) with high effectiveness is required to efficiently transfer the core thermal output to secondary fluid for electricity production, process heat, or hydrogen cogeneration. The current Technology Readiness Level status issued by NGNP to all components associated with the IHX for reactor core outlet temperatures of 750-800oC is 3 on a scale of 1 to 10 with 10 being the most ready. At present, there is no proven high-temperature IHX concept for VHTRs. Amongst the various potential IHX concepts available, diffusion bonded heat exchangers (henceforth called printed circuit heat exchangers, or PCHEs) appear promising for NGNP applications. The design and fabrication of this key component of NGNP is the primary focus of this paper. In the current study, two PCHEs were fabricated using Alloy 617 plates and will be experimentally investigated for their thermal-hydraulic performance in a high-temperature helium test facility (HTHF). The HTHF was primarily designed and constructed to test the thermal-hydraulic performance of PCHEs The test facility is primarily of Alloy 800H construction and is designed to facilitate experiments at temperatures and pressures up to 800oC and 3 MPa, respectively. The PCHE fabrication related processes, i.e., photochemical machining and diffusion bonding are briefly discussed for Alloy 617 plates. Diffusion bonding of Alloy 617 plates with and without a Ni interlayer is discussed. Furthermore, preliminary microstructural and mechanical characterization studies of representative diffusion bonded Alloy 617 specimens are presented.

  14. Design of a new compact and regular 8 x 8 multiplier using redundant binary number representation 

    E-Print Network [OSTI]

    Gopalan, Mythili

    1992-01-01T23:59:59.000Z

    . The n-bit multiplication time of the multiplier is proportional to logan. A modified redundant to binary converter is proposed. This resulted in a reduction of the delay time and the number of transistors of the multiplier. The multiplier adopted a.... The 8 x 8 multiplier was designed and simulated with both the converters. The modified converter reduced the delay time by 13. 7%, area by 33. 69% and number of transistors by 12. 9%. Estimates of area and speed for longer word lengths(16 x 16 and 32...

  15. Innovative High Energy Density Capacitor Design Offers Potential for Clean Energy Applications

    Office of Energy Efficiency and Renewable Energy (EERE)

    Can you imagine a photovoltaic module that’s able to generate and store electricity on its own? Or an electric vehicle (EV) powered by a technology more durable than the advanced batteries in today’s EVs? Innovative solid-state nanocapacitors are making this clean technology possible.

  16. Fabrication and Design Aspects of High-Temperature Compact Diffusion Bonded Heat Exchangers

    SciTech Connect (OSTI)

    Sai K. Mylavarapu; Richard N. Christensen; Raymond R. Unocic; Richard E. Glosup; Mike W. Patterson

    2012-08-01T23:59:59.000Z

    The Very High Temperature Reactor (VHTR) using gas-cooled reactor technology is anticipated to be the reactor type for the Next Generation Nuclear Plant (NGNP). In this reactor concept with an indirect power cycle system, a high-temperature and high integrity Intermediate Heat Exchanger (IHX) with high effectiveness is required to efficiently transfer the core thermal output to a secondary fluid for electricity generation, hydrogen production, and/or industrial process heat applications. At present, there is no proven IHX concept for VHTRs. The current Technology Readiness Level (TRL) status issued by NGNP to all components associated with the IHX for reduced nominal reactor outlet temperatures of 750–800 degrees C is 3 on a 1–10 scale, with 10 indicating omplete technological maturity. Among the various potential IHX concepts available, diffusion bonded heat exchangers (henceforth called printed circuit heat exchangers, or PCHEs) appear promising for NGNP applications. The design and fabrication of this key component of NGNP with Alloy 617, a candidate high-temperature structural material for NGNP applications, are the primary focus of this paper. In the current study, diffusion bonding of Alloy 617 has been demonstrated, although the optimum diffusion bonding process parameters to engineer a quasi interface-free joint are yet to be determined. The PCHE fabrication related processes, i.e., photochemical etching and diffusion bonding are discussed for Alloy 617 plates. In addition, the authors’ experiences with these non-conventional machining and joining techniques are discussed. Two PCHEs are fabricated using Alloy 617 plates and are being experimentally investigated for their thermal-hydraulic performance in a High-Temperature Helium Facility (HTHF). The HTHF is primarily of Alloy 800H construction and is designed to facilitate experiments at temperatures and pressures up to 800 degrees C and 3 MPa, respectively. Furthermore, some preliminary microstructural and mechanical property characterization studies of representative diffusion bonded Alloy 617 specimens are presented. The characterization studies are restricted and less severe from an NGNP perspective but provide sufficient confidence to ensure safe operation of the heat exchangers in the HTHF. The test results are used to determine the design operating conditions for the PCHEs fabricated.

  17. DESIGN AND DEVELOPMENT OF GAS-LIQUID CYLINDRICAL CYCLONE COMPACT SEPARATORS FOR THREE-PHASE FLOW

    SciTech Connect (OSTI)

    Dr. Ram S. Mohan; Dr. Ovadia Shoham

    2001-04-30T23:59:59.000Z

    This report presents a brief overview of the activities and tasks accomplished during the first half year (October 1, 2000-March 31, 2001) of the fourth project year budget period (October 1, 2000-September 30, 2001). An executive summary is presented initially followed by the tasks of the current budget period. Then, detailed description of the experimental and modeling investigations are presented. Subsequently, the technical and scientific results of the activities of this project period are presented with some discussions. The findings of this investigation are summarized in the ''Conclusions'' section followed by relevant references. The fourth project year activities are divided into three main parts, which are carried out in parallel. The first part is continuation of the experimental program that includes a study of the oil/water two-phase behavior at high pressures and control system development for the three-phase GLCC{copyright}. This investigation will be eventually extended for three-phase flow. The second part consists of the development of a simplified mechanistic model incorporating the experimental results and behavior of dispersion of oil in water and water in oil. This will provide an insight into the hydrodynamic flow behavior and serve as the design tool for the industry. Although useful for sizing GLCC{copyright} for proven applications, the mechanistic model will not provide detailed hydrodynamic flow behavior information needed to screen new geometric variations or to study the effect of fluid property variations. Therefore, in the third part, the more rigorous approach of computational fluid dynamics (CFD) will be utilized. Multidimensional multiphase flow simulation at high pressures and for real crude conditions will provide much greater depth into the understanding of the physical phenomena and the mathematical analysis of three-phase GLCC{copyright} design and performance.

  18. A compact design for a magnetic synchrotron to store beams of hydrogen atoms

    E-Print Network [OSTI]

    van der Poel, Aernout P P; Softley, Timothy P; Bethlem, Hendrick L

    2015-01-01T23:59:59.000Z

    We present a design for an atomic synchrotron consisting of 40 hybrid magnetic hexapole lenses arranged in a circle. We show that for realistic parameters, hydrogen atoms with a velocity up to 600 m/s can be stored in a 1-meter diameter ring, which implies that the atoms can be injected in the ring directly from a pulsed supersonic beam source. This ring can be used to study collisions between stored hydrogen atoms and molecular beams of many different atoms and molecules. The advantage of using a synchrotron is two-fold: (i) the collision partners move in the same direction as the stored atoms, resulting in a small relative velocity and thus a low collision energy, and (ii) by storing atoms for many round-trips, the sensitivity to collisions is enhanced by a factor of 100-1000. In the proposed ring, the cross-sections for collisions between hydrogen, the most abundant atom in the universe, with any atom or molecule that can be put in a beam, including He, H$_2$, CO, ammonia and OH can be measured at energies...

  19. Innovation for Food Retail: The 50% Advanced Energy Design Guide for Grocery Stores

    Broader source: Energy.gov [DOE]

    Find the presentation for the June 3, 2015 webinar on the 50% Advanced Energy Design Guide for Grocery Stores.

  20. Innovative Partnering 

    E-Print Network [OSTI]

    Lowe, Emilie

    2008-01-01T23:59:59.000Z

    Innovative partnering Texas A&M, McKinney develop water conservation venture The University of Texas at Arlington?s Program in Landscape Architect assisted in the design of a one-acre water conservation garden for McKinney. The garden will demonstrate... is to educate city officials, developers, landscapers, homeowners, adults, and chil- dren about water conservation and quality. The center developed a water conservation seminar series and a three-part television series on water conservation that airs...

  1. Design and initial operation of a two-color soft x-ray camera system on the Compact Toroidal Hybrid experiment

    SciTech Connect (OSTI)

    Herfindal, J. L., E-mail: j.herfindal@gmail.com; Dawson, J. D.; Ennis, D. A.; Hartwell, G. J.; Loch, S. D.; Maurer, D. A. [Physics Department, Auburn University, Auburn, Alabama 36849 (United States)

    2014-11-15T23:59:59.000Z

    A multi-camera soft x-ray diagnostic has been developed to measure the equilibrium electron temperature profile and temperature fluctuations due to magnetohydrodynamic activity on the Compact Toroidal Hybrid experiment. The diagnostic consists of three separate cameras each employing two 20-channel diode arrays that view the same plasma region through different beryllium filter thicknesses of 1.8??m and 3.0??m allowing electron temperature measurements between 50 eV and 200 eV. The Compact Toroidal Hybrid is a five-field period current-carrying stellarator, in which the presence of plasma current strongly modifies the rotational transform and degree of asymmetry of the equilibrium. Details of the soft x-ray emission, effects of plasma asymmetry, and impurity line radiation on the design and measurement of the two-color diagnostic are discussed. Preliminary estimates of the temperature perturbation due to sawtooth oscillations observed in these hybrid discharges are given.

  2. Innovative Composites Through Reinforcement Morphology Design - a Bone-Shaped-Short-Fiber Composite

    SciTech Connect (OSTI)

    Zhu, Y.T.; Valdez, J.A.; Beyerlain, I.J.; Stout, M.G.; Zhou, S.; Shi, N.; Lowe, T.C.

    1999-06-29T23:59:59.000Z

    This is the final report of a three-year, Laboratory Directed Research and Development (LDRD) project at Los Alamos National Laboratory (LANL). The objective of this project is to improve the strength and toughness of conventional short-fiber composites by using innovative bone-shaped-short (BSS) fibers as reinforcement. We fabricated a model polyethylene BSS fiber-reinforced polyester-matrix composite to prove that fiber morphology, instead of interfacial strength, solves the problem. Experimental tensile and fracture toughness test results show that BSS fibers can bridge matrix cracks more effectively, and consume many times more energy when pulled out, than conventional-straight-short (CSS) fibers. This leads to both higher strength and fracture toughness for the BSS-fiber composites. A computational model was developed to simulate crack propagation in both BSS- and CSS-fiber composites, accounting for stress concentrations, interface debonding, and fiber pullout. Model predictions were validated by experimental results and will be useful in optimizing BSS-fiber morphology and other material system parameters.

  3. Empowering design through non-visual process: The blind add new vision to innovation

    E-Print Network [OSTI]

    Magario, Rachel

    2012-05-31T23:59:59.000Z

    Magario, a blind student in the business and interaction design graduate programs at the University of Kansas, shows how she was able to overcome the mechanical limitations inherent in a visually oriented academic world. Magario explains how a project...

  4. Assessment of innovative fuel designs for high performance light water reactors

    E-Print Network [OSTI]

    Carpenter, David Michael

    2006-01-01T23:59:59.000Z

    To increase the power density and maximum allowable fuel burnup in light water reactors, new fuel rod designs are investigated. Such fuel is desirable for improving the economic performance light water reactors loaded with ...

  5. Managing Highly Innovative Projects: The Influence of Design Characteristics on Project Valuation

    E-Print Network [OSTI]

    Erzurumlu, S. Sinan; Davies, Jane; Joglekar, Nitin

    2014-04-16T23:59:59.000Z

    ) may raise concerns about associated risks. For example, Phononic Devices in ARPA-E dataset, which was working on a novel method to convert waste heat into usable electric power, presented its current thermoelectric device design in its grant...

  6. Flexible design : an innovative approach for planning water infrastructure systems under uncertainty

    E-Print Network [OSTI]

    Wong, Melanie Kathleen

    2013-01-01T23:59:59.000Z

    This thesis develops a framework for a flexible design approach to support decision-making in water supply infrastructure planning. It contrasts with a conventional, deterministic planning approach that uses past data or ...

  7. 4.181 Architecture Design Workshop: Researching User Demand for Innovative Offices, Fall 2002

    E-Print Network [OSTI]

    Duffy, Francis, 1940-

    The theme of this Workshop is the design of the changing workplace. The objective of this workshop is to make MIT graduate students fully aware of emerging technological and social trends that are revolutionizing the working ...

  8. Design and field test of collaborative tools in the service of an innovative organization

    SciTech Connect (OSTI)

    De Beler, N.; Parfouru, S. [EdF R and D -Industrial Risk Management Dept., Human Factors Group, 1, avenue du General de Gaulle, 92 141 Clamart Cedex (France)

    2012-07-01T23:59:59.000Z

    This paper presents the design process of collaborative tools, based on ICT, aiming at supporting the tasks of the team that manages an outage of an energy production plant for maintenance activities. The design process follows an iterative and multidisciplinary approach, based on a collective tasks modeling of the outage management team in the light of Socio Organizational and Human (SOH) field studies, and on the state of the art of ICT. Field test of the collaborative tools designed plays a great place in this approach, allowing taking into account the operational world but involves also some risks which must be managed. To implement tools on all the production plants, we build an 'operational concept' with a level of description which authorizes the evolution of tools and allows some local adaptations. The field tests provide lessons on the ICT topics. For examples: the status of the remote access tools, the potential of use of a given information input by an actor for several individual and collective purposes, the actors perception of the tools meaning, and the requirements for supporting the implementation of change. (authors)

  9. Vehicle Technologies Office Merit Review 2014: Innovative Cell...

    Office of Environmental Management (EM)

    Innovative Cell Materials and Design for 300 Mile Range EVs Vehicle Technologies Office Merit Review 2014: Innovative Cell Materials and Design for 300 Mile Range EVs Presentation...

  10. Improving SFR Economics through Innovations from Thermal Design and Analysis Aspects

    SciTech Connect (OSTI)

    Haihua Zhao; Hongbin Zhang; Vincent Mousseau; Per F. Peterson

    2008-06-01T23:59:59.000Z

    Achieving economic competitiveness as compared to LWRs and other Generation IV (Gen-IV) reactors is one of the major requirements for large-scale investment in commercial sodium cooled fast reactor (SFR) power plants. Advances in R&D for advanced SFR fuel and structural materials provide key long-term opportunities to improve SFR economics. In addition, other new opportunities are emerging to further improve SFR economics. This paper provides an overview on potential ideas from the perspective of thermal hydraulics to improve SFR economics. These include a new hybrid loop-pool reactor design to further optimize economics, safety, and reliability of SFRs with more flexibility, a multiple reheat and intercooling helium Brayton cycle to improve plant thermal efficiency and reduce safety related overnight and operation costs, and modern multi-physics thermal analysis methods to reduce analysis uncertainties and associated requirements for over-conservatism in reactor design. This paper reviews advances in all three of these areas and their potential beneficial impacts on SFR economics.

  11. Innovation Institutions NOVEMBER 2012

    E-Print Network [OSTI]

    Ghosh, Joydeep

    for a design partner #12;#12;#12;MAYBAUM home appliances 1973 Xerox markets first hand-held "mouse," a time battles." IDEATION INNOVATION #12;What makes a company good at bringing innovation to market? #12;Our with smarts of leaders/managers #12;Rational Agents Model Leadership = "Go there" Managers execute

  12. Innovative grinding wheel design for cost-effective machining of advanced ceramics. Phase I, final report

    SciTech Connect (OSTI)

    Licht, R.H.; Ramanath, S.; Simpson, M.; Lilley, E.

    1996-02-01T23:59:59.000Z

    Norton Company successfully completed the 16-month Phase I technical effort to define requirements, design, develop, and evaluate a next-generation grinding wheel for cost-effective cylindrical grinding of advanced ceramics. This program was a cooperative effort involving three Norton groups representing a superabrasive grinding wheel manufacturer, a diamond film manufacturing division and a ceramic research center. The program was divided into two technical tasks, Task 1, Analysis of Required Grinding Wheel Characteristics, and Task 2, Design and Prototype Development. In Task 1 we performed a parallel path approach with Superabrasive metal-bond development and the higher technical risk, CVD diamond wheel development. For the Superabrasive approach, Task 1 included bond wear and strength tests to engineer bond-wear characteristics. This task culminated in a small-wheel screening test plunge grinding sialon disks. In Task 2, an improved Superabrasive metal-bond specification for low-cost machining of ceramics in external cylindrical grinding mode was identified. The experimental wheel successfully ground three types of advanced ceramics without the need for wheel dressing. The spindle power consumed by this wheel during test grinding of NC-520 sialon is as much as to 30% lower compared to a standard resin bonded wheel with 100 diamond concentration. The wheel wear with this improved metal bond was an order of magnitude lower than the resin-bonded wheel, which would significantly reduce ceramic grinding costs through fewer wheel changes for retruing and replacements. Evaluation of ceramic specimens from both Tasks 1 and 2 tests for all three ceramic materials did not show evidence of unusual grinding damage. The novel CVD-diamond-wheel approach was incorporated in this program as part of Task 1. The important factors affecting the grinding performance of diamond wheels made by CVD coating preforms were determined.

  13. Compact Absorption Chiller - Energy Innovation Portal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power Administration would like submit the followingth Lomonosov1 COMMUNITYGeothermal Geothermal

  14. Small Business Innovation Research Grant Helps Propel Innovative...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    was acquired by General Electric (GE) last month. The innovative design of the taller wind turbine towers offer greater power potential because higher altitude winds are...

  15. Business Exploration Series SkillSoft's latest content innovation, the Business Exploration Series, was designed to be visually rich and

    E-Print Network [OSTI]

    Maryland, Baltimore County, University of

    Business Exploration Series SkillSoft's latest content innovation, the Business Exploration Series to our Business Skills Courseware Library. The Business Exploration Series provides learners two different learning assets: Business Impact Series Challenge Series Analyze frequently encountered

  16. Energy Innovation Center | Argonne National Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    construction of the Energy Innovation Center. The building is being designed to meet U.S. Green Building Council Leadership in Energy and Environmental Design (LEED) Gold...

  17. Compaction managed mirror bend achromat

    DOE Patents [OSTI]

    Douglas, David (Yorktown, VA)

    2005-10-18T23:59:59.000Z

    A method for controlling the momentum compaction in a beam of charged particles. The method includes a compaction-managed mirror bend achromat (CMMBA) that provides a beamline design that retains the large momentum acceptance of a conventional mirror bend achromat. The CMMBA also provides the ability to tailor the system momentum compaction spectrum as desired for specific applications. The CMMBA enables magnetostatic management of the longitudinal phase space in Energy Recovery Linacs (ERLs) thereby alleviating the need for harmonic linearization of the RF waveform.

  18. Compact approach to fusion power reactors

    SciTech Connect (OSTI)

    Hagenson, R.L.; Krakowski, R.A.; Bathke, C.G.; Miller, R.L.

    1984-01-01T23:59:59.000Z

    The potential of the Reversed-Field Pinch (RFP) for development into an efficient, compact, copper-coil fusion reactor has been quantified by comprehensive parametric tradeoff studies. These compact systems promise to be competitive in size, power density, and cost to alternative energy sources. Conceptual engineering designs that largely substantiate these promising results have since been completed. This 1000-MWe(net) design is described along with a detailed rationale and physics/technology assessment for the compact approach to fusion.

  19. Keystone Innovation Zone Tax Credit Program (Pennsylvania)

    Broader source: Energy.gov [DOE]

    The Keystone Innovation Zone Tax Credit Program provides tax credits to companies less than eight years old who operate within designated innovation zones. A total pool of $25 million in tax...

  20. Compact Spreader Schemes

    SciTech Connect (OSTI)

    Placidi, M.; Jung, J. -Y.; Ratti, A.; Sun, C.

    2014-07-25T23:59:59.000Z

    This paper describes beam distribution schemes adopting a novel implementation based on low amplitude vertical deflections combined with horizontal ones generated by Lambertson-type septum magnets. This scheme offers substantial compactness in the longitudinal layouts of the beam lines and increased flexibility for beam delivery of multiple beam lines on a shot-to-shot basis. Fast kickers (FK) or transverse electric field RF Deflectors (RFD) provide the low amplitude deflections. Initially proposed at the Stanford Linear Accelerator Center (SLAC) as tools for beam diagnostics and more recently adopted for multiline beam pattern schemes, RFDs offer repetition capabilities and a likely better amplitude reproducibility when compared to FKs, which, in turn, offer more modest financial involvements both in construction and operation. Both solutions represent an ideal approach for the design of compact beam distribution systems resulting in space and cost savings while preserving flexibility and beam quality.

  1. Compact Solid State Cooling Systems: Compact MEMS Electrocaloric Module

    SciTech Connect (OSTI)

    None

    2010-10-01T23:59:59.000Z

    BEETIT Project: UCLA is developing a novel solid-state cooling technology to translate a recent scientific discovery of the so-called giant electrocaloric effect into commercially viable compact cooling systems. Traditional air conditioners use noisy, vapor compression systems that include a polluting liquid refrigerant to circulate within the air conditioner, absorb heat, and pump the heat out into the environment. Electrocaloric materials achieve the same result by heating up when placed within an electric field and cooling down when removed—effectively pumping heat out from a cooler to warmer environment. This electrocaloric-based solid state cooling system is quiet and does not use liquid refrigerants. The innovation includes developing nano-structured materials and reliable interfaces for heat exchange. With these innovations and advances in micro/nano-scale manufacturing technologies pioneered by semiconductor companies, UCLA is aiming to extend the performance/reliability of the cooling module.

  2. Pecos River Compact (Texas)

    Broader source: Energy.gov [DOE]

    This legislation authorizes the state's entrance into the Pecos River Compact, a joint agreement between the states of New Mexico and Texas. The compact is administered by the Pecos River Compact...

  3. Patent Law and Complementary Innovations Yann Mnirey

    E-Print Network [OSTI]

    Boyer, Edmond

    Patent Law and Complementary Innovations Yann Ménièrey CERNA, Ecole Nationale Supérieure des mines: Innovation, Patent, R&D, Complementarity I am grateful to John Barton, Matthieu Glachant, François Lévêque #12;The patent system was initially designed to provide incentives to develop stand-alone innovations

  4. Innovative decision-making methods for the preliminary design and operations of air-cushion and other marine vehicles

    E-Print Network [OSTI]

    Gougoulidis, Georgios

    2011-01-01T23:59:59.000Z

    Ship design is a large-scale, multi-level, complex problem that requires decision-making at every stage of the design process. As such, it requires a great deal of time and resources. The evolution of the process of ship ...

  5. 2015 Hydrogen Student Design Contest Challenges Students to Develop Innovative Hydrogen Fueling Station Business and Financing Models

    Broader source: Energy.gov [DOE]

    The Hydrogen Education Foundation announced the 11th annual Hydrogen Student Design Contest, which will challenge student teams to develop business and financing models for hydrogen fueling stations. Registration for the Contest is open until January 16, 2015.

  6. Innovation and Transportation's Technologies

    E-Print Network [OSTI]

    Garrison, William L.

    2001-01-01T23:59:59.000Z

    decision making. Innovation and technology lock-in hasStage 1 imagine the innovation and technology developmentof emphasizing innovation and technology development. Pull

  7. NSTX LTXPEGASUS Compact CTF

    E-Print Network [OSTI]

    Princeton Plasma Physics Laboratory

    isotope retention. ST-CTF Compact ST-CTF at ~ 10 MA range provide a compact nuclear component test to NSTX. Large vacuum vessel, no stabilizing plates, excellent set of profile and boundary diagnostics

  8. Red River Compact (Texas)

    Broader source: Energy.gov [DOE]

    The Red River Compact Commission administers the Red River Compact to ensure that Texas receives its equitable share of quality water from the Red River and its tributaries as apportioned by the...

  9. Rio Grande Compact (Texas)

    Broader source: Energy.gov [DOE]

    This legislation authorizes the state's entrance into the Rio Grande Compact, a joint agreement between the states of Colorado, New Mexico, and Texas. The compact is administered by the Rio Grande...

  10. Canadian River Compact (Texas)

    Broader source: Energy.gov [DOE]

    The Canadian River Commission administers the Canadian River Compact which includes the states of New Mexico, Oklahoma, and Texas. Signed in 1950 by the member states, the Compact was subsequently...

  11. INNOVATION. PARTNERSHIP.

    E-Print Network [OSTI]

    California at Davis, University of

    RESEARCH. INNOVATION. PARTNERSHIP. WESTERN COOLING EFFICIENCY CENTER ANNUAL REPORT ON COOLING a new structure, or in a near- crisis when the existing system breaks...a decision that prob- ably won with cooling in California. These trends create some of the key challenges faced by the Western Cooling

  12. Compact heat exchangers for condensation applications: Yesterday, today and tomorrow

    SciTech Connect (OSTI)

    Panchal, C.B.

    1993-07-01T23:59:59.000Z

    Compact heat exchangers are being increasingly considered for condensation applications in the process, cryogenic, aerospace, power and refrigeration industries. In this paper, different configurations available for condensation applications are analyzed and the current state-of-the-knowledge for the design of compact condensers is evaluated. The key technical issues for the design and development of compact heat exchangers for condensation applications are analyzed and major advantages are identified. The experimental data and performance prediction methods reported in the literature are analyzed to evaluate the present design capabilities for different compact heat-exchanger configurations. The design flexibility is evaluated for the development of new condensation applications, including integration with other process equipment.

  13. avances systemes innovants: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    explores the use of genetic programming as a tool in the system design and innovation process. Digital circuits are used as a proxy for complex technological designs. Circuit...

  14. Implementation of an Innovative Bio Inspired GA and PSO Algorithm for Controller design considering Steam GT Dynamics

    E-Print Network [OSTI]

    Shivakumar, R

    2010-01-01T23:59:59.000Z

    The Application of Bio Inspired Algorithms to complicated Power System Stability Problems has recently attracted the researchers in the field of Artificial Intelligence. Low frequency oscillations after a disturbance in a Power system, if not sufficiently damped, can drive the system unstable. This paper provides a systematic procedure to damp the low frequency oscillations based on Bio Inspired Genetic (GA) and Particle Swarm Optimization (PSO) algorithms. The proposed controller design is based on formulating a System Damping ratio enhancement based Optimization criterion to compute the optimal controller parameters for better stability. The Novel and contrasting feature of this work is the mathematical modeling and simulation of the Synchronous generator model including the Steam Governor Turbine (GT) dynamics. To show the robustness of the proposed controller, Non linear Time domain simulations have been carried out under various system operating conditions. Also, a detailed Comparative study has been don...

  15. Sustainable Innovation 

    E-Print Network [OSTI]

    Armendariz, A.

    2011-01-01T23:59:59.000Z

    or Unsustainable a) Rate of consumption of energy and matter b) Consumption, toxicity, and persistence c) Unintended consequences (2) Solutions a) Systems thinking b) Sources of Innovation c) Ideality (3) Regional challenges -- dead zone, wetlands loss... lived the way Americans live? If everyone in the world lived the way Americans live? We would need 4 planet earths to support them all. Not only quantity -- Toxicity ? Toxics Release Inventory (TRI) ? 4.44 billion lbs. of toxic chemicals...

  16. Opportunity Thinking for Open Innovation innovation?

    E-Print Network [OSTI]

    Ghosh, Joydeep

    · Technology innovation process · Shared services Copyright © 2012 NewEdge25 #12;Leveraging multiple sourcesOpportunity Thinking for Open Innovation #12;Why open innovation? Copyright © 2012 NewEdge2 #12;Opportunity! Open innovation promises to make an attractive opportunity even more attractive. · Better

  17. B.G. Thomas and S.P. Vanka, 2002 NSF Design, Service, Manufacturing and Industrial Innovation Research Conf., San Juan, Puerto Rico, January 7-10, 2002.

    E-Print Network [OSTI]

    Thomas, Brian G.

    Research Conf., San Juan, Puerto Rico, January 7-10, 2002. 1 Flow Dynamics and Inclusion Transport Innovation Research Conf., San Juan, Puerto Rico, January 7-10, 2002. 2 1. INTRODUCTION Continued viability

  18. Interstate Mining Compact (Maryland)

    Broader source: Energy.gov [DOE]

    This legislation authorizes the state's entrance into the Interstate Mining Compact, a multi-state governmental agency / organization that represents the natural resource and related environmental...

  19. Innovative Partnering

    E-Print Network [OSTI]

    Lowe, Emilie

    2008-01-01T23:59:59.000Z

    tx H2O | pg. 14 T he city of McKinney, Texas and Texas AgriLife Research and Extension Urban Solutions Center at Dallas are partnering on a six-year plan to educate and bring research-based innovations to McKinney residents. The goal... is to help them manage water resources efficiently. This partnership developed after the summer of 2006 when McKinney, one of the fastest growing cities in the United States, was faced with a severe drought that placed the city in a stage three drought...

  20. Innovation Celebration

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHigh SchoolIn Other News linkThermalInner Area Principles TheInnovation

  1. Innovation Prize

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHigh SchoolIn Other News linkThermalInner Area PrinciplesInnovationSinha

  2. aeropropulsion compact lightweight: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    24 25 Next Page Last Page Topic Index 1 Design of a compact, lightweight, and low-cost solar concentrator MIT - DSpace Summary: The objective of this mechanical design project was...

  3. BUILDING CODES: BARRIERS TO GREEN INNOVATION

    E-Print Network [OSTI]

    BUILDING CODES: BARRIERS TO GREEN INNOVATION JENNIFER GARMAN DR. JIM BOWYER DR. STEVE BRATKOVICH/18/2011 DOVETAIL PARTNERS, INC. www.dovetailinc.org Building Codes: Barriers to Green Innovation Introduction Many architects and contractors want to pursue green building design, technologies and construction. Green

  4. Laboratory compaction of cohesionless sands

    E-Print Network [OSTI]

    Delphia, John Girard

    1998-01-01T23:59:59.000Z

    on the maximum dry unit weight during compaction. Three different laboratory compaction methods were used: 1) Standard Proctor', 2) Modified Proctor; and 3) Vibrating hammer. The effects of the grain size distribution, particle shape and laboratory compaction...

  5. Design Parameters for a 7.2 Tesla Bending Magnet for a 1.5 GeV Compact Light Source

    E-Print Network [OSTI]

    Green, M.A.

    2011-01-01T23:59:59.000Z

    a Central Induction of 7 tesla [l] D. B. Cline A. A. Gmen.Design Parameters for a 7.2 Tesla Bending Magnet for a 1.5Design Parameters for a 7.2 Tesla Bending Magnet for a 1.5

  6. Scientific Innovation Through Integration Investing in Innovation

    E-Print Network [OSTI]

    Scientific Innovation Through Integration Investing in Innovation: EMSL and the American Recovery transfer (FRET) in living cells. Transcriptional profiling using next-generation sequencing technology (RNA Act, EMSL users are benefitting from a $60 million investment in innovation that will further develop

  7. Compact microchannel system

    DOE Patents [OSTI]

    Griffiths, Stewart

    2003-09-30T23:59:59.000Z

    The present invention provides compact geometries for the layout of microchannel columns through the use of turns and straight channel segments. These compact geometries permit the use of long separation or reaction columns on a small microchannel substrate or, equivalently, permit columns of a fixed length to occupy a smaller substrate area. The new geometries are based in part on mathematical analyses that provide the minimum turn radius for which column performance in not degraded. In particular, we find that straight channel segments of sufficient length reduce the required minimum turn radius, enabling compact channel layout when turns and straight segments are combined. The compact geometries are obtained by using turns and straight segments in overlapped or nested arrangements to form pleated or coiled columns.

  8. Science, technology and innovation

    E-Print Network [OSTI]

    Sussex, University of

    Science, technology and innovation Taught degrees MSc in Innovation and Sustainability for International Development 1 year full time/2 years part time Technological innovation lies at the heart in the academic and political circles related to the impact of science, technology and innovation in the context

  9. UU Innovation UUAB Holding

    E-Print Network [OSTI]

    Uppsala Universitet

    UU Innovation UUAB Holding ANNUAL REVIEW 2013 #12;UU Innovation is the central innovation support at the university. Through UUAB Holding the university can contribute to licensing of new technology and establish new research-based companies. IN BRIEF UU INNOVATION UUAB HOLDING TO FACILITATE MUTUAL knowledge

  10. Carbon Markets and Technological Innovation

    E-Print Network [OSTI]

    Weber, T A; Neuhoff, Karsten

    www.eprg.group.cam.ac.uk E P R G W O R K IN G P A P E R N O N -T E C H N IC A L S U M M A R Y Carbon Markets and Technological Innovation EPRG Working Paper 0917 Cambridge Working Paper in Economics 0932 Thomas A. Weber... and Karsten Neuhoff This paper examines how considering firm-level innovation in carbon-abatement technologies influences the optimal design choice for carbon pricing. It builds on Weitzman’s model (1974) that shows in what instances cap and trade...

  11. Proposals for Technology Innovation Projects Student technology fees are intended to enhance student learning and the student

    E-Print Network [OSTI]

    Farritor, Shane

    Proposals for Technology Innovation Projects Student technology fees scale if effective. Timeline Applications for Technology Innovation Projects innovative ideas about using technology? 2) Is the project designed to be led

  12. War Upon the Map: The Politics of Military User Innovation

    E-Print Network [OSTI]

    Lindsay, Jon R.

    2006-07-18T23:59:59.000Z

    While military personnel are often involved in the design of information technology, the literature on military innovation generally assumes defense contractors are the primary producers. Furthermore, general organizational ...

  13. Penn State Consortium for Building Energy Innovation | Department...

    Broader source: Energy.gov (indexed) [DOE]

    a best practices model for commercial building design, historic adaptive re-use, and energy efficiency innovation through continuous retrofit. The Center for Building Energy...

  14. Small Businesses Nationwide Begin Work on Cutting-Edge Innovative...

    Office of Environmental Management (EM)

    work this week on 180 innovative research projects ranging from designing better wind turbines to developing a chemical-free approach to killing bacteria in power plant cooling...

  15. Quality Management System Guidelines - Building America Top Innovation...

    Energy Savers [EERE]

    (PHI) created custom quality management system guidelines for the design and construction of high performance homes, earning a 2013 Top Innovation award for their efforts....

  16. Strategy Guideline: Compact Air Distribution Systems

    SciTech Connect (OSTI)

    Burdick, A.

    2013-06-01T23:59:59.000Z

    This Strategy Guideline discusses the benefits and challenges of using a compact air distribution system to handle the reduced loads and reduced air volume needed to condition the space within an energy efficient home. Traditional systems sized by 'rule of thumb' (i.e., 1 ton of cooling per 400 ft2 of floor space) that 'wash' the exterior walls with conditioned air from floor registers cannot provide appropriate air mixing and moisture removal in low-load homes. A compact air distribution system locates the HVAC equipment centrally with shorter ducts run to interior walls, and ceiling supply outlets throw the air toward the exterior walls along the ceiling plane; alternatively, high sidewall supply outlets throw the air toward the exterior walls. Potential drawbacks include resistance from installing contractors or code officials who are unfamiliar with compact air distribution systems, as well as a lack of availability of low-cost high sidewall or ceiling supply outlets to meet the low air volumes with good throw characteristics. The decision criteria for a compact air distribution system must be determined early in the whole-house design process, considering both supply and return air design. However, careful installation of a compact air distribution system can result in lower material costs from smaller equipment, shorter duct runs, and fewer outlets; increased installation efficiencies, including ease of fitting the system into conditioned space; lower loads on a better balanced HVAC system, and overall improved energy efficiency of the home.

  17. Compact, Interactive Electric Vehicle Charger: Gallium-Nitride Switch Technology for Bi-directional Battery-to-Grid Charger Applications

    SciTech Connect (OSTI)

    None

    2010-10-01T23:59:59.000Z

    ADEPT Project: HRL Laboratories is using gallium nitride (GaN) semiconductors to create battery chargers for electric vehicles (EVs) that are more compact and efficient than traditional EV chargers. Reducing the size and weight of the battery charger is important because it would help improve the overall performance of the EV. GaN semiconductors process electricity faster than the silicon semiconductors used in most conventional EV battery chargers. These high-speed semiconductors can be paired with lighter-weight electrical circuit components, which helps decrease the overall weight of the EV battery charger. HRL Laboratories is combining the performance advantages of GaN semiconductors with an innovative, interactive battery-to-grid energy distribution design. This design would support 2-way power flow, enabling EV battery chargers to not only draw energy from the power grid, but also store and feed energy back into it.

  18. Technology Innovation Program Transforming America's Future Through Innovation

    E-Print Network [OSTI]

    Technology Innovation Program Transforming America's Future Through Innovation 2009ANNUAL REPORT and Technology Dr. Patrick D. Gallagher, Director Technology Innovation Program Dr. Lorel Wisniewski, Acting Director National Institute of Standards and Technology Technology Innovation Program 100 Bureau Drive

  19. Stimulating Energy Technology Innovation

    E-Print Network [OSTI]

    Moniz, Ernest J.

    The innovation system has interrelated components of invention, translation, adoption, and diffusion. Energy technology innovation has lagged that in other domains, and there is a compelling public interest in picking up ...

  20. Industrial Optimization Compact Course

    E-Print Network [OSTI]

    Kirches, Christian

    Industrial Optimization Compact Course and Challenge Workshop Optimization plays a crucial role of the processes are typically nonlinear and dyna- mic. Thus, complex dynamic optimization or optimal control in industrial optimization. February 17­20, 2014 ·9.00­17.00 IWR ·Im Neuenheimer Feld 368 ·69120 Heidelberg www

  1. The Technology & Innovation Centre

    E-Print Network [OSTI]

    Mottram, Nigel

    The Technology & Innovation Centre #12;The Technology and Innovation Centre revolutionises the way in Scotland and further afield ­ including power and energy, renewable technologies, photonics and sensors, for industry, the Technology and Innovation Centre has already attracted major partners including Scottish

  2. Bridging the Technology Innovation

    E-Print Network [OSTI]

    Wirosoetisno, Djoko

    Bridging the Technology Innovation Gap Dr Ceri Williams Director of Medical Technologies Innovation Technologies #12;Distinctive Approach to Translating ResearchWe support innovation to reach TRL 5 enable real and Knowledge Centre #12;What is the Medical Technologies IKC? · All activities centre on research translation

  3. Progress in Compact Toroid Experiments

    SciTech Connect (OSTI)

    Dolan, Thomas James

    2002-09-01T23:59:59.000Z

    The term "compact toroids" as used here means spherical tokamaks, spheromaks, and field reversed configurations, but not reversed field pinches. There are about 17 compact toroid experiments under construction or operating, with approximate parameters listed in Table 1.

  4. Sabine River Compact (Multiple States)

    Broader source: Energy.gov [DOE]

    The Sabine River Compact Commission administers the Sabine River Compact to ensure that Texas receives its equitable share of quality water from the Sabine River and its tributaries as apportioned...

  5. Introduction and Motivation Toward Group Optimization to Design Building Systems

    E-Print Network [OSTI]

    Paulino, Glaucio H.

    and different perspectives, better innovative and responsive design solutions could be developed than either

  6. Accelerating Innovation: We Do It Together

    Broader source: Energy.gov [DOE]

    The debut of a 3D printed car, an EV version of the 50th anniversary Shelby Cobra, this week at the Detroit Auto Show is a big win for manufacturing innovation. Accelerating innovation is about meeting big technical challenges and addressing the challenge in a short timeframe. Developing new manufacturing technology to design, print, construct and display the Shelby Cobra is a great example of what can be achieved by a team.

  7. Technology Innovation Program 2010ANNUAL REPORT

    E-Print Network [OSTI]

    Technology Innovation Program 2010ANNUAL REPORT 2010ANNUAL REPORT Technology Innovation ProgramTechnology Innovation ProgramTechnology Innovation ProgramTechnology Innovation ProgramTechnology Innovation ProgramTechnology Innovation ProgramTechnology Innovation ProgramTechnology Innovation ProgramTechnology Innovation ProgramTechnology

  8. A Compact Wireless Charging System for Electric Vehicles

    SciTech Connect (OSTI)

    Ning, Puqi [ORNL] [ORNL; Miller, John M [ORNL] [ORNL; Onar, Omer C [ORNL] [ORNL; White, Cliff P [ORNL] [ORNL

    2013-01-01T23:59:59.000Z

    In this paper, a compact high efficiency wireless power transfer system has been designed and developed. The detailed gate drive design, cooling system design, power stage development, and system assembling are presented. The successful tests verified the feasibility of wireless power transfer system to achieve over-all 90% efficiency.

  9. Global Compact for Higher Education Institutions

    E-Print Network [OSTI]

    Global Compact for Higher Education Institutions Communicating on Progress for Université Laval Guide to the United Nations Global Compact for Higher Education Institutions: Implementing the Global to the United Nations Global Compact for Higher Education Institutions: Implementing the Global Compact

  10. COMPACTION OF FIBERBOARD OVERPACK MATERIALS IN A 9975 SHIPPING PACKAGE

    SciTech Connect (OSTI)

    Stefek, T.; Daugherty, W.; Estochen, E.; Murphy, J.

    2010-05-27T23:59:59.000Z

    Compaction of lower layers in the 9975 fiberboard overpack has been observed in packages that contain excess moisture. Dynamic loading of the package during transportation may also contribute to compaction of the fiberboard. This condition is being tested and analyzed to better understand these compaction mechanisms and provide a basis from which to evaluate their impact to the safety basis for transportation (Safety Analysis Report for Packaging) and storage (facility Design Safety Analysis) at the Savannah River Site (SRS). A test program has been developed and is being implemented to identify the extent of the compaction as a function of fiberboard moisture and typical transport dynamic loadings. Test conditions will be compared to regulatory requirements for dynamic loading. Characterization of the recovery of short-term compaction following the application of dynamic loading is also being evaluated. Interim results from this test program will be summarized.

  11. Center of Innovation- Energy

    Broader source: Energy.gov [DOE]

    Jill Stuckey, Director, Center fof Innovation - Energy, presents on Georgia's workforce development opportunities for the Biomass/Clean Cities States Webinar.

  12. Innovation enabling manufacturing processes

    E-Print Network [OSTI]

    Lu, Ilyssa Jing

    2008-01-01T23:59:59.000Z

    Global operations for multinational companies today pose a particularly challenging environment for maintaining fluid knowledge transfer and effective communication methodologies. In a continuous drive for product innovation, ...

  13. Innovation Strategies and Ideas

    E-Print Network [OSTI]

    Datta, Shoumen

    2008-08-01T23:59:59.000Z

    Convergence is the central theme advocated in these suggestions for global economic growth through entrepreneurial innovation strategies which may catalyse building of enterprises with creative dimensions.

  14. Accretion in Compact Binaries

    E-Print Network [OSTI]

    Andrew R. King

    2003-03-26T23:59:59.000Z

    Compact binaries have long been a paradigm for accretion theory. Much of our present view of how accretion occurs comes directly from the comparison of theory with observations of these sources. Since theory differs little for other objects such as active galaxies, increasing efforts have recently gone into searching for correspondences in observed behaviour. This chapter aims at giving a concise summary of the field, with particular emphasis on new developments since the previous edition of this book. These developments have been significant. Much of the earlier literature implicitly assumed that accreting binaries were fairly steady sources accreting most of the mass entering their vicinity, often with main-sequence companions, and radiating the resulting accretion luminosity in rough isotropy. We shall see that in reality these assumptions fail for the majority of systems. Most are transient; mass ejection in winds and jets is extremely common; a large (sometimes dominant) fraction of even short-period systems have evolved companions whose structure deviates significantly from the zero-age main sequence; and the radiation pattern of many objects is significantly anisotropic. It is now possible to give a complete characterization of the observed incidence of transient and persistent sources in terms of the disc instability model and formation constraints. X-ray populations in external galaxies, particularly the ultraluminous sources, are revealing important new insights into accretion processes and compact binary evolution.

  15. From Producer Innovation to User and Open Collaborative Innovation

    E-Print Network [OSTI]

    Baldwin, Carliss

    In this paper we assess the economic viability of innovation by producers relative to two increasingly important alternative models: innovations by single user individuals or firms, and

  16. Susquehanna River Basin Compact (Maryland)

    Broader source: Energy.gov [DOE]

    This legislation enables the state's entrance into the Susquehanna River Basin Compact, which provides for the conservation, development, and administration of the water resources of the...

  17. INNOVATION IN AUTOMOTIVE TELEMATICS SERVICES: CHARACTERISTICS OF THE FIELD AND

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    INNOVATION IN AUTOMOTIVE TELEMATICS SERVICES: CHARACTERISTICS OF THE FIELD AND MANAGEMENT is a radical innovation for automotive industry. Therefore traditional design models, such as heavyweight, published in "Int. J. of Automotive Technology et Management 3, 1/2 (2003) 144-159" #12;2 communication

  18. Compact acoustic refrigerator

    DOE Patents [OSTI]

    Bennett, G.A.

    1992-11-24T23:59:59.000Z

    A compact acoustic refrigeration system actively cools components, e.g., electrical circuits, in a borehole environment. An acoustic engine includes first thermodynamic elements for generating a standing acoustic wave in a selected medium. An acoustic refrigerator includes second thermodynamic elements located in the standing wave for generating a relatively cold temperature at a first end of the second thermodynamic elements and a relatively hot temperature at a second end of the second thermodynamic elements. A resonator volume cooperates with the first and second thermodynamic elements to support the standing wave. To accommodate the high heat fluxes required for heat transfer to/from the first and second thermodynamic elements, first heat pipes transfer heat from the heat load to the second thermodynamic elements and second heat pipes transfer heat from first and second thermodynamic elements to the borehole environment. 18 figs.

  19. Compact acoustic refrigerator

    DOE Patents [OSTI]

    Bennett, Gloria A. (Los Alamos, NM)

    1992-01-01T23:59:59.000Z

    A compact acoustic refrigeration system actively cools components, e.g., electrical circuits (22), in a borehole environment. An acoustic engine (12, 14) includes first thermodynamic elements (12) for generating a standing acoustic wave in a selected medium. An acoustic refrigerator (16, 26, 28) includes second thermodynamic elements (16) located in the standing wave for generating a relatively cold temperature at a first end of the second thermodynamic elements (16) and a relatively hot temperature at a second end of the second thermodynamic elements (16). A resonator volume (18) cooperates with the first and second thermodynamic elements (12, 16) to support the standing wave. To accommodate the high heat fluxes required for heat transfer to/from the first and second thermodynamic elements (12, 16), first heat pipes (24, 26) transfer heat from the heat load (22) to the second thermodynamic elements (16) and second heat pipes (28, 32) transfer heat from first and second thermodynamic elements (12, 16) to the borehole environment.

  20. Compact vacuum insulation embodiments

    DOE Patents [OSTI]

    Benson, D.K.; Potter, T.F.

    1992-04-28T23:59:59.000Z

    An ultra-thin compact vacuum insulation panel is comprised of two hard, but bendable metal wall sheets closely spaced apart from each other and welded around the edges to enclose a vacuum chamber. Glass or ceramic spacers hold the wall sheets apart. The spacers can be discrete spherical beads or monolithic sheets of glass or ceramic webs with nodules protruding therefrom to form essentially point' or line' contacts with the metal wall sheets. In the case of monolithic spacers that form line' contacts, two such spacers with the line contacts running perpendicular to each other form effectively point' contacts at the intersections. Corrugations accommodate bending and expansion, tubular insulated pipes and conduits, and preferred applications are also included. 26 figs.

  1. Compact vacuum insulation

    DOE Patents [OSTI]

    Benson, David K. (Golden, CO); Potter, Thomas F. (Denver, CO)

    1993-01-01T23:59:59.000Z

    An ultra-thin compact vacuum insulation panel is comprised of two hard, but bendable metal wall sheets closely spaced apart from each other and welded around the edges to enclose a vacuum chamber. Glass or ceramic spacers hold the wall sheets apart. The spacers can be discrete spherical beads or monolithic sheets of glass or ceramic webs with nodules protruding therefrom to form essentially "point" or "line" contacts with the metal wall sheets. In the case of monolithic spacers that form "line" contacts, two such spacers with the line contacts running perpendicular to each other form effectively "point" contacts at the intersections. Corrugations accommodate bending and expansion, tubular insulated pipes and conduits, and preferred applications are also included.

  2. Compact vacuum insulation

    DOE Patents [OSTI]

    Benson, D.K.; Potter, T.F.

    1993-01-05T23:59:59.000Z

    An ultra-thin compact vacuum insulation panel is comprised of two hard, but bendable metal wall sheets closely spaced apart from each other and welded around the edges to enclose a vacuum chamber. Glass or ceramic spacers hold the wall sheets apart. The spacers can be discrete spherical beads or monolithic sheets of glass or ceramic webs with nodules protruding therefrom to form essentially point'' or line'' contacts with the metal wall sheets. In the case of monolithic spacers that form line'' contacts, two such spacers with the line contacts running perpendicular to each other form effectively point'' contacts at the intersections. Corrugations accommodate bending and expansion, tubular insulated pipes and conduits, and preferred applications are also included.

  3. Compact vacuum insulation embodiments

    DOE Patents [OSTI]

    Benson, David K. (Golden, CO); Potter, Thomas F. (Denver, CO)

    1992-01-01T23:59:59.000Z

    An ultra-thin compact vacuum insulation panel is comprised of two hard, but bendable metal wall sheets closely spaced apart from each other and welded around the edges to enclose a vacuum chamber. Glass or ceramic spacers hold the wall sheets apart. The spacers can be discrete spherical beads or monolithic sheets of glass or ceramic webs with nodules protruding therefrom to form essentially "point" or "line" contacts with the metal wall sheets. In the case of monolithic spacers that form "line" contacts, two such spacers with the line contacts running perpendicular to each other form effectively "point" contacts at the intersections. Corrugations accommodate bending and expansion, tubular insulated pipes and conduits, and preferred applications are also included.

  4. A compact tritium AMS system

    SciTech Connect (OSTI)

    Chiarappa, M L; Dingley, K H; Hamm, R W; Love, A H; Roberts, M L

    1999-09-23T23:59:59.000Z

    Tritium ({sup 3}H) is a radioisotope that is extensively utilized in biological and environmental research. For biological research, {sup 3}H is generally quantified by liquid scintillation counting requiring gram-sized samples and counting times of several hours. For environmental research, {sup 3}H is usually quantified by {sup 3}He in-growth which requires gram-sized samples and in-growth times of several months. In contrast, provisional studies at LLNL's Center for Accelerator Mass Spectrometry have demonstrated that Accelerator Mass Spectrometry (AMS) can be used to quantify {sup 3}H in milligram-sized biological samples with a 100 to 1000-fold improvement in detection limits when compared to scintillation counting. This increased sensitivity is expected to have great impact in the biological and environmental research community. However in order to make the {sup 3}H AMS technique more broadly accessible, smaller, simpler, and less expensive AMS instrumentation must be developed. To meet this need, a compact, relatively low cost prototype {sup 3}H AMS system has been designed and built based on a LLNL ion source/sample changer and an AccSys Technology, Inc. Radio Frequency Quadrupole (RFQ) linac. With the prototype system, {sup 3}/{sup 1}H ratios ranging from 1 x 10{sup -10} to 1 x 10{sup -13} have to be measured from milligram sized samples. With improvements in system operation and sample preparation methodology, the sensitivity limit of the system is expected to increase to approximately 1 x 10{sup -15}.

  5. Enterprise Innovation Institute Annual Report 2009

    E-Print Network [OSTI]

    Das, Suman

    the application of science, technology, and innovation. Enterprise Innovation Institute (EI2)Enterprise Innovation of all types and sizes use science, technology, and innovation to improve their competitiveness survey of Georgia's health care information technology industry. The Enterprise Innovation Institute

  6. NREL Spectrum of Innovation

    ScienceCinema (OSTI)

    None

    2013-05-29T23:59:59.000Z

    There are many voices calling for a future of abundant clean energy. The choices are difficult and the challenges daunting. How will we get there? The National Renewable Energy Laboratory integrates the entire spectrum of innovation including fundamental science, market relevant research, systems integration, testing and validation, commercialization and deployment. The innovation process at NREL is interdependent and iterative. Many scientific breakthroughs begin in our own laboratories, but new ideas and technologies come to NREL at any point along the innovation spectrum to be validated and refined for commercial use.

  7. An Innovative Approach Towards National Peak Load Management

    E-Print Network [OSTI]

    Al-Mulla, A.; Maheshwari, G. P.; Al-Nakib, D.; ElSherbini, A.; Alghimlas, F.; Al-Taqi, H.; Al-Hadban, Y.

    especially designed fluorescent lamps for the offices, besides using highly energy efficient light emitting diodes (LEDs). The corridors are mostly lit with fluorescent tubes and compact fluorescent lamps (CFLs). MC and MOH buildings have retrofitted... especially designed fluorescent lamps for the offices, besides using highly energy efficient light emitting diodes (LEDs). The corridors are mostly lit with fluorescent tubes and compact fluorescent lamps (CFLs). MC and MOH buildings have retrofitted...

  8. Use of a BCD for compaction control

    E-Print Network [OSTI]

    Li, Yanfeng

    2005-11-01T23:59:59.000Z

    Compaction of soil is essential in the construction of highways, airports, buildings, and bridges. Typically compaction is controlled by measuring the dry density and the water content of the compacted soil and checking that target values have been...

  9. Alternative Landfill Cover. Innovative Technology Summary Report

    SciTech Connect (OSTI)

    NONE

    2000-12-01T23:59:59.000Z

    The primary purpose of an engineered cover is to isolate the underlying waste. A key element to isolating the wastes from the environment, engineered covers should minimize or prevent water from infiltrating into the landfill and coming into contact with the waste, thereby minimizing leachate generation. The U.S. EPA construction guidelines for soil hydraulic barriers specify that the soil moisture content and compactive effort may be increased to ensure that the barrier achieves a specified permeability of 1 x 10{sup {minus}7} cm/sec. However, constructing a soil barrier with high moisture content makes the soil more difficult to work and increases the required compactive effort to achieve the specified density, ultimately increasing the construction cost of the barrier. Alternative landfill cover designs rely on soil physical properties, hydraulic characteristics, and vegetation requirements to lower the flux rate of water through the cover. They can achieve greater reliability than the prescriptive RCRA Subtitle C design, especially under arid or semi-arid environmental conditions. With an alternative cover design, compacted soil barriers can be constructed with a soil moisture content that makes placement and compaction of the soil easier and less expensive. Under these conditions, the soil barrier has more capacity to absorb and control moisture within it, thereby enhancing the reliability of the barrier. This document contains information on the above-mentioned technology, including description, applicability, cost, and performance, data.

  10. Three essays on the development and diffusion of pharmaceutical innovations

    E-Print Network [OSTI]

    Azoulay, Pierre

    2001-01-01T23:59:59.000Z

    The thesis comprises three essays on various aspects of the development and diffusion of pharmaceutical innovations, woven together by the idea that the production of clinical knowl- edge influences organizational design, ...

  11. Innovative solar thermochemical water splitting.

    SciTech Connect (OSTI)

    Hogan, Roy E. Jr.; Siegel, Nathan P.; Evans, Lindsey R.; Moss, Timothy A.; Stuecker, John Nicholas (Robocasting Enterprises, Albuquerque, NM); Diver, Richard B., Jr.; Miller, James Edward; Allendorf, Mark D. (Sandia National Laboratories, Livermore, CA); James, Darryl L. (Texas Tech University, Lubbock, TX)

    2008-02-01T23:59:59.000Z

    Sandia National Laboratories (SNL) is evaluating the potential of an innovative approach for splitting water into hydrogen and oxygen using two-step thermochemical cycles. Thermochemical cycles are heat engines that utilize high-temperature heat to produce chemical work. Like their mechanical work-producing counterparts, their efficiency depends on operating temperature and on the irreversibility of their internal processes. With this in mind, we have invented innovative design concepts for two-step solar-driven thermochemical heat engines based on iron oxide and iron oxide mixed with other metal oxides (ferrites). The design concepts utilize two sets of moving beds of ferrite reactant material in close proximity and moving in opposite directions to overcome a major impediment to achieving high efficiency--thermal recuperation between solids in efficient counter-current arrangements. They also provide inherent separation of the product hydrogen and oxygen and are an excellent match with high-concentration solar flux. However, they also impose unique requirements on the ferrite reactants and materials of construction as well as an understanding of the chemical and cycle thermodynamics. In this report the Counter-Rotating-Ring Receiver/Reactor/Recuperator (CR5) solar thermochemical heat engine and its basic operating principals are described. Preliminary thermal efficiency estimates are presented and discussed. Our ferrite reactant material development activities, thermodynamic studies, test results, and prototype hardware development are also presented.

  12. Compact vacuum insulation

    DOE Patents [OSTI]

    Benson, D.K.; Potter, T.F.

    1992-10-27T23:59:59.000Z

    Improved compact insulation panel is provided which is comprised of two adjacent metal sheets spaced close together with a plurality of spherical, or other discretely shaped, glass or ceramic beads optimally positioned between the sheets to provide support and maintain the spacing between the metal sheets when the gases there between are evacuated to form a vacuum. These spherical glass beads provide the maximum support while minimizing thermal conductance. In its preferred embodiment; these two metal sheets are textured with ribs or concave protrusions in conjunction with the glass beads to maximize the structural integrity of the panels while increasing the spacing between beads, thereby reducing the number of beads and the number of thermal conduction paths. Glass or porcelain-enameled liners in combination with the glass spacers and metal sidewalls effectively decrease thermal conductivity, and various laminates, including wood, porcelain-enameled metal, and others effectively increase the strength and insulation capabilities of the panels. Also, a metal web is provided to hold the spacers in place, and strategic grooves are shown to accommodate expansion and contraction or shaping of the panels. 35 figs.

  13. Compact vacuum insulation

    DOE Patents [OSTI]

    Benson, David K. (Golden, CO); Potter, Thomas F. (Denver, CO)

    1992-01-01T23:59:59.000Z

    Improved compact insulation panel is provided which is comprised of two adjacent metal sheets spaced close together with a plurality of spherical, or other discretely shaped, glass or ceramic beads optimally positioned between the sheets to provide support and maintain the spacing between the metal sheets when the gases therebetween are evacuated to form a vacuum. These spherical glass beads provide the maximum support while minimizing thermal conductance. In its preferred embodiment; these two metal sheets are textured with ribs or concave protrusions in conjunction with the glass beads to maximize the structural integrity of the panels while increasing the spacing between beads, thereby reducing the number of beads and the number of thermal conduction paths. Glass or porcelain-enameled liners in combination with the glass spacers and metal sidewalls effectively decrease thermal conductivity, and variious laminates, including wood, porcelain-enameled metal, and others effectively increase the strength and insulation capabilities of the panels. Also, a metal web is provided to hold the spacers in place, and strategic grooves are shown to accommodate expansion and contraction or shaping of the panels.

  14. Compact neutron generator

    DOE Patents [OSTI]

    Leung, Ka-Ngo; Lou, Tak Pui

    2005-03-22T23:59:59.000Z

    A compact neutron generator has at its outer circumference a toroidal shaped plasma chamber in which a tritium (or other) plasma is generated. A RF antenna is wrapped around the plasma chamber. A plurality of tritium ion beamlets are extracted through spaced extraction apertures of a plasma electrode on the inner surface of the toroidal plasma chamber and directed inwardly toward the center of neutron generator. The beamlets pass through spaced acceleration and focusing electrodes to a neutron generating target at the center of neutron generator. The target is typically made of titanium tubing. Water is flowed through the tubing for cooling. The beam can be pulsed rapidly to achieve ultrashort neutron bursts. The target may be moved rapidly up and down so that the average power deposited on the surface of the target may be kept at a reasonable level. The neutron generator can produce fast neutrons from a T-T reaction which can be used for luggage and cargo interrogation applications. A luggage or cargo inspection system has a pulsed T-T neutron generator or source at the center, surrounded by associated gamma detectors and other components for identifying explosives or other contraband.

  15. Innovative and Advanced Coupled Neutron Transport and Thermal Hydraulic Method (Tool) for the Design, Analysis and Optimization of VHTR/NGNP Prismatic Reactors

    SciTech Connect (OSTI)

    Rahnema, Farzad; Garimeela, Srinivas; Ougouag, Abderrafi; Zhang, Dingkang

    2013-11-29T23:59:59.000Z

    This project will develop a 3D, advanced coarse mesh transport method (COMET-Hex) for steady- state and transient analyses in advanced very high-temperature reactors (VHTRs). The project will lead to a coupled neutronics and thermal hydraulic (T/H) core simulation tool with fuel depletion capability. The computational tool will be developed in hexagonal geometry, based solely on transport theory without (spatial) homogenization in complicated 3D geometries. In addition to the hexagonal geometry extension, collaborators will concurrently develop three additional capabilities to increase the code’s versatility as an advanced and robust core simulator for VHTRs. First, the project team will develop and implement a depletion method within the core simulator. Second, the team will develop an elementary (proof-of-concept) 1D time-dependent transport method for efficient transient analyses. The third capability will be a thermal hydraulic method coupled to the neutronics transport module for VHTRs. Current advancements in reactor core design are pushing VHTRs toward greater core and fuel heterogeneity to pursue higher burn-ups, efficiently transmute used fuel, maximize energy production, and improve plant economics and safety. As a result, an accurate and efficient neutron transport, with capabilities to treat heterogeneous burnable poison effects, is highly desirable for predicting VHTR neutronics performance. This research project’s primary objective is to advance the state of the art for reactor analysis.

  16. Compact Reversed-Field Pinch Reactors (CRFPR): preliminary engineering considerations

    SciTech Connect (OSTI)

    Hagenson, R.L.; Krakowski, R.A.; Bathke, C.G.; Miller, R.L.; Embrechts, M.J.; Schnurr, N.M.; Battat, M.E.; LaBauve, R.J.; Davidson, J.W.

    1984-08-01T23:59:59.000Z

    The unique confinement physics of the Reversed-Field Pinch (RFP) projects to a compact, high-power-density fusion reactor that promises a significant reduction in the cost of electricity. The compact reactor also promises a factor-of-two reduction in the fraction of total cost devoted to the reactor plant equipment (i.e., fusion power core (FPC) plus support systems). In addition to operational and developmental benefits, these physically smaller systems can operate economically over a range of total power output. After giving an extended background and rationale for the compact fusion approaches, key FPC subsystems for the Compact RFP Reactor (CRFPR) are developed, designed, and integrated for a minimum-cost, 1000-MWe(net) system. Both the problems and promise of the compact, high-power-density fusion reactor are quantitatively evaluated on the basis of this conceptual design. The material presented in this report both forms a framework for a broader, more expanded conceptual design as well as suggests directions and emphases for related research and development.

  17. Compact and highly efficient laser pump cavity

    DOE Patents [OSTI]

    Chang, Jim J. (Dublin, CA); Bass, Isaac L. (Castro Valley, CA); Zapata, Luis E. (Livermore, CA)

    1999-01-01T23:59:59.000Z

    A new, compact, side-pumped laser pump cavity design which uses non-conventional optics for injection of laser-diode light into a laser pump chamber includes a plurality of elongated light concentration channels. In one embodiment, the light concentration channels are compound parabolic concentrators (CPC) which have very small exit apertures so that light will not escape from the pumping chamber and will be multiply reflected through the laser rod. This new design effectively traps the pump radiation inside the pump chamber that encloses the laser rod. It enables more uniform laser pumping and highly effective recycle of pump radiation, leading to significantly improved laser performance. This new design also effectively widens the acceptable radiation wavelength of the diodes, resulting in a more reliable laser performance with lower cost.

  18. New considerations for compact cyclotrons

    E-Print Network [OSTI]

    Marshall, Eric S. (Eric Scott)

    2012-01-01T23:59:59.000Z

    A compact cyclotron built with superconducting magnets could be a transformative solution to many scientific problems facing the defense, medical, and energy industries today. This thesis discusses three potential applications ...

  19. MESOSCALE SIMULATIONS OF POWDER COMPACTION

    SciTech Connect (OSTI)

    Lomov, Ilya; Fujino, Don; Antoun, Tarabay; Liu, Benjamin [Lawrence Livermore National Laboratory, P. O. Box 808, Livermore CA 94551 (United States)

    2009-12-28T23:59:59.000Z

    Mesoscale 3D simulations of shock compaction of metal and ceramic powders have been performed with an Eulerian hydrocode GEODYN. The approach was validated by simulating a well-characterized shock compaction experiment of a porous ductile metal. Simulation results using the Steinberg material model and handbook values for solid 2024 aluminum showed good agreement with experimental compaction curves and wave profiles. Brittle ceramic materials are not as well studied as metals, so a simple material model for solid ceramic (tungsten carbide) has been calibrated to match experimental compaction curves. Direct simulations of gas gun experiments with ceramic powders have been performed and showed good agreement with experimental data. The numerical shock wave profile has same character and thickness as that measured experimentally using VISAR. The numerical results show reshock states above the single-shock Hugoniot line as observed in experiments. We found that for good quantitative agreement with experiments 3D simulations are essential.

  20. Yellowstone River Compact (North Dakota)

    Broader source: Energy.gov [DOE]

    The Yellowstone River Compact, agreed to by the States of Montana, North Dakota, and Wyoming, provides for an equitable division and apportionment of the waters of the Yellowstone River, as well as...

  1. Research in the field of design and manufacturing at Bath is pulled together in the University's Innovative Design and Manufacturing Research Centre (IdMRC). The centre is unique in the

    E-Print Network [OSTI]

    Burton, Geoffrey R.

    such as aircraft wings, large gearboxes and wind turbine blades. However, a limited industry track record Design and manufacturing #12;Interacting with machines and materials To succeed in today's market developed at the University, called the machine-material interaction methodology, uses a continuous

  2. Regional Resource Centers for Innovation Brochure (Revised)

    SciTech Connect (OSTI)

    Wogsland, J.

    2000-09-14T23:59:59.000Z

    This brochure describes OIT's Regional Resource Centers for Innovation (RCIs), which provide the Innovation and Invention program grantees and other small business energy innovators commercialization assistance.

  3. Innovative . Flexible . RegionalInnovative . Flexible . Regional Health Care

    E-Print Network [OSTI]

    Shihadeh, Alan

    Executive Master in Innovative . Flexible . RegionalInnovative . Flexible . Regional Health Care Learning Outcomes Health Systems, Policy and Reform - Communicating with Policy Makers - Evidence - Human Resources Management - Data and Decision Making Executive Master in Health Care Leadership (EMHCL

  4. ForPeerReview THE LINK BETWEEN NON TECHNOLOGICAL INNOVATIONS

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    ForPeerReview THE LINK BETWEEN NON TECHNOLOGICAL INNOVATIONS AND TECHNOLOGICAL INNOVATION Journal: Organizational innovation, Marketing innovation, Technological Innovation, Performance European Journal THE LINK BETWEEN NON TECHNOLOGICAL INNOVATIONS AND TECHNOLOGICAL INNOVATION Abstract Purpose This paper

  5. Recent progress on the Compact Ignition Tokamak (CIT)

    SciTech Connect (OSTI)

    Ignat, D.W.

    1987-01-01T23:59:59.000Z

    This report describes work done on the Compact Ignition Tokamak (CIT), both at the Princeton Plasma Physics Laboratory (PPPL) and at other fusion laboratories in the United States. The goal of CIT is to reach ignition in a tokamak fusion device in the mid-1990's. Scientific and engineering features of the design are described, as well as projected cost and schedule.

  6. Exploratory Divertor Heat Load Studies for Compact Stellarator Reactors

    E-Print Network [OSTI]

    Raffray, A. René

    of the divertor system is described in Sec. III, together with the plate heat load profile, and the conditions is power reaching the plate, AD is the total plate area, Wpk is the design peak heat load limitExploratory Divertor Heat Load Studies for Compact Stellarator Reactors T.K. Maua , H. Mc

  7. Compact reactor/ORC power source

    SciTech Connect (OSTI)

    Meier, K.L.; Kirchner, W.L.; Willcutt, G.J.

    1986-01-01T23:59:59.000Z

    A compact power source that combines an organic Rankine Cycle (ORC) electric generator with a nuclear reactor heat source is being designed and fabricated. Incorporating existing ORC technology with proven reactor technology, the compact reactor/ORC power source offers high reliability while minimizing the need for component development. Thermal power at 125 kWt is removed from the coated particle fueled, graphite moderated reactor by heat pipes operating at 500/sup 0/C. Outside the reactor vessel and connected to the heat pipes are vaporizers in which the toluene ORC working fluid is heated to 370/sup 0/C. In the turbine-alternator-pump (TAP) combined-rotating unit, the thermal energy of the toluene is converted to 25 kWe of electric power. Lumped parameter systems analyses combined with a finite element thermal analysis have aided in the power source design. The analyses have provided assurance of reliable multiyear normal operation as well as full power operation with upset conditions, such as failed heat pipes and inoperative ORC vaporizers. Because of inherent high reliability, long life, and insensitivity to upset conditions, this power source is especially suited for use in remote, inaccessible locations where fuel delivery and maintenance costs are high. 10 refs.

  8. Tools for innovation and conceptual design

    E-Print Network [OSTI]

    Karuppoor, Srinand Sreedharan

    2004-11-15T23:59:59.000Z

    to that function. ? Look for interfaces between a function and the environment. Look for extremes in the influence of the performance of the function on the environment and vice versa. ? Introduce quantification of the functions and constraints to establish...

  9. Innovative design of uranium startup fast reactors

    E-Print Network [OSTI]

    Fei, Tingzhou

    2012-01-01T23:59:59.000Z

    Sodium Fast Reactors are one of the three candidates of GEN-IV fast reactors. Fast reactors play an important role in saving uranium resources and reducing nuclear wastes. Conventional fast reactors rely on transuranic ...

  10. An Innovative High Thermal Conductivity Fuel Design

    SciTech Connect (OSTI)

    Jamil A. Khan

    2009-11-21T23:59:59.000Z

    Thermal conductivity of the fuel in today's Light Water Reactors, Uranium dioxide, can be improved by incorporating a uniformly distributed heat conducting network of a higher conductivity material, Silicon Carbide. The higher thermal conductivity of SiC along with its other prominent reactor-grade properties makes it a potential material to address some of the related issues when used in UO2 [97% TD]. This ongoing research, in collaboration with the University of Florida, aims to investigate the feasibility and develop a formal methodology of producing the resultant composite oxide fuel. Calculations of effective thermal conductivity of the new fuel as a function of %SiC for certain percentages and as a function of temperature are presented as a preliminary approach. The effective thermal conductivities are obtained at different temperatures from 600K to 1600K. The corresponding polynomial equations for the temperature-dependent thermal conductivities are given based on the simulation results. Heat transfer mechanism in this fuel is explained using a finite volume approach and validated against existing empirical models. FLUENT 6.1.22 was used for thermal conductivity calculations and to estimate reduction in centerline temperatures achievable within such a fuel rod. Later, computer codes COMBINE-PC and VENTURE-PC were deployed to estimate the fuel enrichment required, to maintain the same burnup levels, corresponding to a volume percent addition of SiC.

  11. Innovative Exploration Technologies Subprogram Overview

    Broader source: Energy.gov [DOE]

    This overview of GTP's Innovative Exploration Technologies subprogram was given at the GTP Program Peer Review on May 18, 2010.

  12. Solar Innovator | Alta Devices

    ScienceCinema (OSTI)

    Mattos, Laila; Le, Minh

    2013-05-29T23:59:59.000Z

    Selected to participate in the Energy Department's SunShot Initiative, Alta Devices produces solar cells that convert sunlight into electricity at world record-breaking levels of efficiency. Through its innovative solar technology Alta is helping bring down the cost of solar. Learn more about the Energy Department's efforts to advance solar technology at energy.gov/solar .

  13. INNOVATION EDUCATION EXCELLENCE DISTILLATIONS

    E-Print Network [OSTI]

    Chan, Hue Sun

    INNOVATION · EDUCATION · EXCELLENCE DISTILLATIONS University of Toronto CHEMISTRY ALUMNI MAGAZINE.utoronto.ca / distillations 2012 MessagefromtheChair Our Department of Chemistry has one of the finest collection of peo- ple to a better, more sustain- able future. This issue of Distillations highlights the accomplishments last year

  14. Innovation in Computer Sciences

    E-Print Network [OSTI]

    Ghosh, Joydeep

    power- up Innovation in Computer Sciences Department of Computer Sciences at The University of Texas at Austin #12;#12;Computer science is the enabling science of our age. It is the engine. In the Department of Computer Sciences at The University of Texas at Austin, one of the top ten departments

  15. Compact orthogonal NMR field sensor

    DOE Patents [OSTI]

    Gerald, II, Rex E. (Brookfield, IL); Rathke, Jerome W. (Homer Glen, IL)

    2009-02-03T23:59:59.000Z

    A Compact Orthogonal Field Sensor for emitting two orthogonal electro-magnetic fields in a common space. More particularly, a replacement inductor for existing NMR (Nuclear Magnetic Resonance) sensors to allow for NMR imaging. The Compact Orthogonal Field Sensor has a conductive coil and a central conductor electrically connected in series. The central conductor is at least partially surrounded by the coil. The coil and central conductor are electrically or electro-magnetically connected to a device having a means for producing or inducing a current through the coil and central conductor. The Compact Orthogonal Field Sensor can be used in NMR imaging applications to determine the position and the associated NMR spectrum of a sample within the electro-magnetic field of the central conductor.

  16. Technology Innovation Program Advisory Board

    E-Print Network [OSTI]

    Magee, Joseph W.

    Technology Innovation Program Advisory Board 2009 Annual Report of the #12;2009 Annual Report of the Technology Innovation Program Advisory Board U.S. Department of Commerce National Institute of Standards and Technology Technology Innovation Program February 2010 #12;For Information regarding the Technology

  17. Technology Innovation Program Advisory Board

    E-Print Network [OSTI]

    Technology Innovation Program Advisory Board 2009 Annual Report of the Technology Innovation Program Advisory Board 2010 Annual Report of the #12;2010 Annual Report of the Technology Innovation Program Advisory Board U.S. Department of Commerce National Institute of Standards and Technology

  18. Technology Innovation Program Advisory Board

    E-Print Network [OSTI]

    Technology Innovation Program Advisory Board 2011 Annual Report of the #12;#12;i 2011 Annual Report of the Technology Innovation Program Advisory Board U.S. Department of Commerce National Institute of Standards and Technology Technology Innovation Program March 2012 #12;ii For Information regarding the Technology

  19. Separations innovative concepts: Project summary

    SciTech Connect (OSTI)

    Lee, V.E. (ed.)

    1988-05-01T23:59:59.000Z

    This project summary includes the results of 10 innovations that were funded under the US Department's Innovative Concept Programs. The concepts address innovations that can substantially reduce the energy used in industrial separations. Each paper describes the proposed concept, and discusses the concept's potential energy savings, market applications, technical feasibility, prior work and state of the art, and future development needs.

  20. Leveraging Resources for the Weatherization Innovation Pilot...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    the Weatherization Innovation Pilot Program (WIPP) - Webinar Transcript Leveraging Resources for the Weatherization Innovation Pilot Program (WIPP) - Webinar Transcript This...

  1. Leveraging Resources for Weatherization Innovation Pilot Projects...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Weatherization Innovation Pilot Projects (WIPP) Presentation Leveraging Resources for Weatherization Innovation Pilot Projects (WIPP) Presentation As a WIPP agency, reporting...

  2. Globalization of Innovation: The Personal Computing Industry

    E-Print Network [OSTI]

    Dedrick, Jason; Kraemer, Kenneth L

    2007-01-01T23:59:59.000Z

    Production Outsourced to CM or ODM Incremental innovation (desktops, notebooks) -Innovate on Wintel architecture -Control product planning,

  3. Compact monolithic capacitive discharge unit

    DOE Patents [OSTI]

    Roesler, Alexander W. (Tijeras, NM); Vernon, George E. (Rio Rancho, NM); Hoke, Darren A. (Albuquerque, NM); De Marquis, Virginia K. (Tijeras, NM); Harris, Steven M. (Albuquerque, NM)

    2007-06-26T23:59:59.000Z

    A compact monolithic capacitive discharge unit (CDU) is disclosed in which a thyristor switch and a flyback charging circuit are both sandwiched about a ceramic energy storage capacitor. The result is a compact rugged assembly which provides a low-inductance current discharge path. The flyback charging circuit preferably includes a low-temperature co-fired ceramic transformer. The CDU can further include one or more ceramic substrates for enclosing the thyristor switch and for holding various passive components used in the flyback charging circuit. A load such as a detonator can also be attached directly to the CDU.

  4. Compact accelerator for medical therapy

    DOE Patents [OSTI]

    Caporaso, George J.; Chen, Yu-Jiuan; Hawkins, Steven A.; Sampayan, Stephen E.; Paul, Arthur C.

    2010-05-04T23:59:59.000Z

    A compact accelerator system having an integrated particle generator-linear accelerator with a compact, small-scale construction capable of producing an energetic (.about.70-250 MeV) proton beam or other nuclei and transporting the beam direction to a medical therapy patient without the need for bending magnets or other hardware often required for remote beam transport. The integrated particle generator-accelerator is actuable as a unitary body on a support structure to enable scanning of a particle beam by direction actuation of the particle generator-accelerator.

  5. Centrifugal shot blasting. Innovative technology summary report

    SciTech Connect (OSTI)

    Not Available

    1999-07-01T23:59:59.000Z

    At the US Department of Energy (DOE) Fernald Environmental Management Project (FEMP), the Facilities Closure and Demolition Projects Integrated Remedial Design/Remedial Action (RD/RA) work plan calls for the removal of one inch (1 in) depth of concrete surface in areas where contamination with technetium-99 has been identified. This report describes a comparative demonstration between two concrete removal technologies: an innovative system using Centrifugal Shot Blasting (CSB) and a modified baseline technology called a rotary drum planer.

  6. A compact broadband multilayer patch antenna and its applications for phased arrays

    E-Print Network [OSTI]

    Kidder, Charles Crandall

    2002-01-01T23:59:59.000Z

    complexity of the antenna. This thesis details the work done on developing a broadband patch antenna that is compact and easily manufactured. Three antenna designs are detailed herein. Simulation and measured results indicate that the double II-shaped u...

  7. Innovative, Cost Effective and Energy Efficient Desgin for New Construction at a Texas High School 

    E-Print Network [OSTI]

    Khan, S.; Bible, M.

    2013-01-01T23:59:59.000Z

    construction in the design phase can result in greater operating efficiency and environmental impact. These measures entail innovative design concepts and control schemes in addition to specification of premium efficiency equipment. This paper presents...

  8. Mesoscale Simulations of Power Compaction

    SciTech Connect (OSTI)

    Lomov, I; Fujino, D; Antoun, T; Liu, B

    2009-08-06T23:59:59.000Z

    Mesoscale 3D simulations of metal and ceramic powder compaction in shock waves have been performed with an Eulerian hydrocode GEODYN. The approach was validated by simulating shock compaction of porous well-characterized ductile metal using Steinberg material model. Results of the simulations with handbook values for parameters of solid 2024 aluminum have good agreement with experimental compaction curves and wave profiles. Brittle ceramic materials are not so well studied as metals, so material model for ceramic (tungsten carbide) has been fitted to shock compression experiments of non-porous samples and further calibrated to match experimental compaction curves. Direct simulations of gas gun experiments with ceramic powder have been performed and showed good agreement with experimental data. Numerical shock wave profile has same character and thickness as measured with VISAR. Numerical results show reshock states above the single-shock Hugoniot line also observed in experiments. They found that to receive good quantitative agreement with experiment it is essential to perform 3D simulations.

  9. A compact layout for a 50 GeV proton radiography facility

    SciTech Connect (OSTI)

    Neri, F. (Filippo); Mottershead, C. T.; Blind, B. (Barbara); Jason, A. J. (Andrew J.); Walstrom, P. L. (Peter L.); Schulze, M. E. (Martin E.); Rybarcyk, L. J. (Lawrence J.); Wang, T. F. (Tai-Sen F.); Thiessen, H. A.; Colestock, P. L. (Patrick L.),; Prichard, B. (Ben)

    2003-01-01T23:59:59.000Z

    We describe a new compact layout for a 50 GeV proton radiography facility. The more compact design utilizes two-point extraction from the main ring to drive an optimal 8 view imaging system. The lattice design of both the main ring, and of the corresponding 8.5 GeV booster ring is described. The rings have very good longitudinal stability, which is of interest for other applications of high current proton machines in this energy range.

  10. Software Development for a CompactRIO-Based Wire Scanner Control and Data Acquisition SYstem

    SciTech Connect (OSTI)

    Sedillo, James Daniel [Los Alamos National Laboratory

    2012-05-16T23:59:59.000Z

    The Beam Diagnostics and Instrumentation Team at the Los Alamos Neutron Science Center is developing a wire scanner data acquisition and control system with a National Instrument's compactRIO at its core. For this application, the compactRIO controller not only requires programming the FPGA and RT computer internal to the compactRIO, but also requires programming a client computer and a touch panel display. This article will summarize the hardware interfaces and describe the software design approach utilized for programming and interfacing the four systems together in order to fulfill the design requirements and promote reliable interoperability.

  11. Innovating science communication

    E-Print Network [OSTI]

    Goldfarb, Steven; The ATLAS collaboration; Shaw, Kate

    2015-01-01T23:59:59.000Z

    The ATLAS Education & Outreach project has, over the years, developed a strong reputation for supporting innovation. Animated event displays, musical CDs, 3d movies, 3-storey murals, photo books, data sonifications, multi-media art installations, pub slams, masterclasses, documentaries, pop-up books, LEGO® models, and virtual visits are among the many diverse methods being exploited to communicate to the world the goals and accomplishments of the ATLAS Experiment at CERN. This variety of creativity and innovation does not pop out of a vacuum. It requires underlying motivation by the collaboration to communicate with the public; freedom and encouragement to do so in a creative manner; and a support structure for developing, implementing and promoting these activities. The ATLAS Outreach project has built this support structure on a well-defined communication plan, high-quality content, and effective delivery platforms. Most importantly, implementation of the program has been based on the effective engagem...

  12. Raytheon's next generation compact inline cryocooler architecture

    SciTech Connect (OSTI)

    Schaefer, B. R.; Bellis, L.; Ellis, M. J.; Conrad, T. [Raytheon Space and Airborne Systems, 2000 E. El Segundo Blvd., El Segundo, CA 90245 (United States)

    2014-01-29T23:59:59.000Z

    Since the 1970s, Raytheon has developed, built, tested and integrated high performance cryocoolers. Our versatile designs for single and multi-stage cryocoolers provide reliable operation for temperatures from 10 to 200 Kelvin with power levels ranging from 50 W to nearly 600 W. These advanced cryocoolers incorporate clearance seals, flexure suspensions, hermetic housings and dynamic balancing to provide long service life and reliable operation in all relevant environments. Today, sensors face a multitude of cryocooler integration challenges such as exported disturbance, efficiency, scalability, maturity, and cost. As a result, cryocooler selection is application dependent, oftentimes requiring extensive trade studies to determine the most suitable architecture. To optimally meet the needs of next generation passive IR sensors, the Compact Inline Raytheon Stirling 1-Stage (CI-RS1), Compact Inline Raytheon Single Stage Pulse Tube (CI-RP1) and Compact Inline Raytheon Hybrid Stirling/Pulse Tube 2-Stage (CI-RSP2) cryocoolers are being developed to satisfy this suite of requirements. This lightweight, compact, efficient, low vibration cryocooler combines proven 1-stage (RS1 or RP1) and 2-stage (RSP2) cold-head architectures with an inventive set of warm-end mechanisms into a single cooler module, allowing the moving mechanisms for the compressor and the Stirling displacer to be consolidated onto a common axis and in a common working volume. The CI cryocooler is a significant departure from the current Stirling cryocoolers in which the compressor mechanisms are remote from the Stirling displacer mechanism. Placing all of the mechanisms in a single volume and on a single axis provides benefits in terms of package size (30% reduction), mass (30% reduction), thermodynamic efficiency (>20% improvement) and exported vibration performance (?25 mN peak in all three orthogonal axes at frequencies from 1 to 500 Hz). The main benefit of axial symmetry is that proven balancing techniques and hardware can be utilized to null all motion along the common axis. Low vibration translates to better sensor performance resulting in simpler, more direct mechanical mounting configurations, eliminating the need for convoluted, expensive, massive, long lead damping hardware.

  13. NREL Innovations Help Drive Wind Industry Transformation (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2013-08-01T23:59:59.000Z

    For nearly 30 years, NREL has helped the wind turbine industry through design and research innovations. The comprehensive capabilities of the National Wind Technology Center (NWTC), ranging from specialized computer simulation tools to unique test facilities, has been used to design, develop, and deploy several generations of advanced wind energy technology.

  14. Design - Make : the translation of design intention to fabrication

    E-Print Network [OSTI]

    McLain, James R

    2007-01-01T23:59:59.000Z

    The process of making innovative buildings is stifled by our current methodology of communicating design information. Advances in new techniques, technologies, methods, materials and knowledge for both designers and ...

  15. Alum Innovative Exploration

    Broader source: Energy.gov [DOE]

    DOE Geothermal Peer Review 2010 - Presentation. Project objectives: Reduce the high level of risk during the early stages of geothermal project development by conducting a multi-faceted and innovative exploration and drilling program at Alum. Determine the combination of techniques that are most useful and cost-effective in identifying the geothermal resource through a detailed, post-project evaluation of the exploration and drilling program.

  16. Innovative Technologies and Techniques

    E-Print Network [OSTI]

    Samano, R.; Swinford, S.

    2014-01-01T23:59:59.000Z

    November 2014 Innovative Technologies and Techniques ESL-KT-14-11-22 CATEE 2014: Clean Air Through Efficiency Conference, Dallas, Texas Nov. 18-20 What’s New in Energy Efficient Cooling Systems? ? Director of Energy Management ? Moving Away From... Refrigerants ? LEED ? Reducing the Carbon Footprint ? Improving Indoor Air Quality - IAQ ? High Efficiency Fans and Motors ? Economizers ESL-KT-14-11-22 CATEE 2014: Clean Air Through Efficiency Conference, Dallas, Texas Nov. 18-20 Outside Air Management Experts...

  17. Interstate Oil and Gas Conservation Compact (Montana)

    Broader source: Energy.gov [DOE]

    This legislation authorizes the State to join the Interstate Compact for the Conservation of Oil and Gas. The Compact is an agreement that has been entered into by 30 oil- and gas-producing states,...

  18. Interstate Oil and Gas Conservation Compact (Maryland)

    Broader source: Energy.gov [DOE]

    This legislation authorizes the State to join the Interstate Compact for the Conservation of Oil and Gas. The Compact is an agreement that has been entered into by 30 oil- and gas-producing states,...

  19. Defense Science and Technology Innovation Teams: Mechanisms and Indicators for Indigenous Innovation in China

    E-Print Network [OSTI]

    WRIGHT, Darren J.

    2015-01-01T23:59:59.000Z

    STUDY OF INNOVATION AND TECHNOLOGY IN CHINA RESEARCH BRIEFThe Study of Innovation and Technology in China (SITC) is aDefense Science and Technology Innovation Teams: Mechanisms

  20. Compact neutron generator development at LBNL

    E-Print Network [OSTI]

    2003-01-01T23:59:59.000Z

    Generator Development at LBNL J. Reijonen, G. English, R.Technology Group in LBNL. The compact axial extraction

  1. Innovation: A data-driven approach Andrew Kusiak

    E-Print Network [OSTI]

    Kusiak, Andrew

    . Some prefer the terms ``technology-based innovation'' or ``technological innovation'' to emphasizeInnovation: A data-driven approach Andrew Kusiak Mechanical and Industrial Engineering, 3131 online 24 June 2009 Keywords: Innovation science Data mining Innovation rules Innovation framework

  2. United Nations Global Compact The UN Global Compact is a strategic policy initiative for

    E-Print Network [OSTI]

    Chatziantoniou, Damianos

    United Nations Global Compact The UN Global Compact is a strategic policy initiative for businesses in the world. The Global Compact pursues two complementary objectives: 1. Mainstream the ten principles the Millennium Development Goals (MDGs). Participation in the Global Compact is open to degree-granting academic

  3. 2015 Hydrogen Student Design Contest Challenges Students to Develop...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    5 Hydrogen Student Design Contest Challenges Students to Develop Innovative Hydrogen Fueling Station Business and Financing Models 2015 Hydrogen Student Design Contest Challenges...

  4. Ultra-Compact High-Efficiency Luminaire for General Illumination

    SciTech Connect (OSTI)

    Ted Lowes

    2012-04-08T23:59:59.000Z

    Cree has developed a new ultra-compact light emitting diode (LED) luminaire capable of providing high efficacy with excellent color quality that can lead to significant energy savings in todayâ??s commercial and retail applications. This success was based on an integrated development effort tailoring the LED component characteristics, optics, thermal management and driver design for the small footprint to achieve an overall system efficiency of â?¥ 70%. A new LED component was designed to provide high brightness and efficacy in a form factor that allowed for a small directional beam with a luminaire housing design able to dissipate the heat effectively using a small physical envelope. A very compact, 90% efficient driver was developed to meet the system performance while not taking away any thermal mass from the heat sink. A 91% efficient secondary optics was designed to maximize efficiency while providing a smooth beam. The reliability of the new LED component was robust under accelerated testing conditions. Luminaires were assembled integrating the novel LED component, secondary optics, heat sink and driver technology to demonstrate the system improvement. Cree has successfully completed this project by developing an ultra-compact LED luminaire that provided 380 lumens at a correlated color temperature (CCT) of 2822 K and color rendering index (CRI) of 94 with an efficacy of 94 lumens per watt (LPW) when operating at 4 W input power (steady state) with an overall system efficiency of 81%. At a higher input power of 9 Watts, the lamp provided 658 lumens at 71 LPW.

  5. Compact portable diffraction moire interferometer

    DOE Patents [OSTI]

    Deason, Vance A. (Shelley, ID); Ward, Michael B. (Idaho Falls, ID)

    1989-01-01T23:59:59.000Z

    A compact and portable moire interferometer used to determine surface deformations of an object. The improved interferometer is comprised of a laser beam, optical and fiber optics devices coupling the beam to one or more evanescent wave splitters, and collimating lenses directing the split beam at one or more specimen gratings. Observation means including film and video cameras may be used to view and record the resultant fringe patterns.

  6. Compact portable diffraction moire interferometer

    DOE Patents [OSTI]

    Deason, V.A.; Ward, M.B.

    1988-05-23T23:59:59.000Z

    A compact and portable moire interferometer used to determine surface deformations of an object. The improved interferometer is comprised of a laser beam, optical and fiber optics devices coupling the beam to one or more evanescent wave splitters, and collimating lenses directing the split beam at one or more specimen gratings. Observations means including film and video cameras may be used to view and record the resultant fringe patterns. 7 figs.

  7. Compact magnetic energy storage module

    DOE Patents [OSTI]

    Prueitt, Melvin L. (Los Alamos, NM)

    1994-01-01T23:59:59.000Z

    A superconducting compact magnetic energy storage module in which a plurality of superconducting toroids, each having a toroidally wound superconducting winding inside a poloidally wound superconducting winding, are stacked so that the flow of electricity in each toroidally wound superconducting winding is in a direction opposite from the direction of electrical flow in other contiguous superconducting toroids. This allows for minimal magnetic pollution outside of the module.

  8. Compact magnetic energy storage module

    DOE Patents [OSTI]

    Prueitt, M.L.

    1994-12-20T23:59:59.000Z

    A superconducting compact magnetic energy storage module in which a plurality of superconducting toroids, each having a toroidally wound superconducting winding inside a poloidally wound superconducting winding, are stacked so that the flow of electricity in each toroidally wound superconducting winding is in a direction opposite from the direction of electrical flow in other contiguous superconducting toroids. This allows for minimal magnetic pollution outside of the module. 4 figures.

  9. On singularities in combination-driven models of technological innovation

    E-Print Network [OSTI]

    Solé, Ricard V; Valverde, Sergi

    2014-01-01T23:59:59.000Z

    It has been suggested that innovations occur mainly by combination: the more inventions accumulate, the higher the probability that new inventions are obtained from previous designs. Additionally, it has been conjectured that the combinatorial nature of innovations naturally leads to a singularity: at some finite time, the number of innovations should diverge. Although these ideas are certainly appealing, no general models have been yet developed to test the conditions under which combinatorial technology should become explosive. Here we present a generalised model of technological evolution that takes into account two major properties: the number of previous technologies needed to create a novel one and how rapidly technology ages. Two different models of combinatorial growth are considered, involving different forms of ageing. When long-range memory is used and thus old inventions are available for novel innovations, singularities can emerge under some conditions with two phases separated by a critical boun...

  10. Innovation Ohio Loan Program (Ohio)

    Broader source: Energy.gov [DOE]

    Innovation Ohio Loan Program provides loans for acquisition, construction, and related costs of technology, facilities, and equipment purchase. The Ohio Department of Development’s (Development)...

  11. Commercialization and Innovation Fact Sheet

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    grant works to acceler- ate the transition of innovative energy efficiency and renewable energy concepts from university laboratories to the market. The i6 Green Challenge grant...

  12. Environmental Regulation, Globalization, and Innovation

    E-Print Network [OSTI]

    Ashford, Nicholas

    2009-01-01T23:59:59.000Z

    This essay explores the complex relationship between environmental regulation, innovation, and sustainable development within the context of an increasingly globalizing economy. It will be argued that industrial policy, ...

  13. Innovative Manufacturing Initiative Recognition Day

    Broader source: Energy.gov [DOE]

    The Innovative Manufacturing Initiative (IMI) Recognition Day (held in Washington, DC on June 20, 2012) showcased IMI projects selected by the Energy Department to help American manufacturers...

  14. Computational Science and Innovation

    E-Print Network [OSTI]

    D. J. Dean

    2010-09-13T23:59:59.000Z

    Simulations - utilizing computers to solve complicated science and engineering problems - are a key ingredient of modern science. The U.S. Department of Energy (DOE) is a world leader in the development of high-performance computing (HPC), the development of applied math and algorithms that utilize the full potential of HPC platforms, and the application of computing to science and engineering problems. An interesting general question is whether the DOE can strategically utilize its capability in simulations to advance innovation more broadly. In this article, I will argue that this is certainly possible.

  15. Innovation | Department of Energy

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItemResearch > The Energy Materials Center at CornellOf NSEC » ISTIandInnovation

  16. Science and Innovation

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItemResearch > TheNuclearHomeland ScienceInnovation

  17. 70 Years of Innovations

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItem NotEnergy, science,SpeedingWu,IntelligenceYou are70 Years of Innovations

  18. Innovation Impact Publications | NREL

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHigh SchoolIn Other News linkThermalInner Area PrinciplesInnovation Impact

  19. Compact

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power Administration would like submit the followingth Lomonosov1 COMMUNITY

  20. Flaw-detection characteristics of the compact MIB-4 betatron

    SciTech Connect (OSTI)

    Boiko, D.A.; Filimonov, A.A.; Chakhlov, V.L.

    1987-09-01T23:59:59.000Z

    The compact pulse betatron using electrons accelerated to an energy of up to 4 MeV (MIB-4) is designed for the radiographic inspection of reinforced-concrete structures and buildings, welded joints, various materials, and assemblies. Information which refines and complements the method of inspecting parts by means of the MIB-4 device is provided. The results obtained in testing this equipment abroad are given.

  1. Compact gas-insulated transformer. Fourteenth quarterly report

    SciTech Connect (OSTI)

    Not Available

    1983-08-01T23:59:59.000Z

    Objective is to develop a compact, more efficient, quieter transformer which does not rely on mineral oil insulation. Compressed SF/sub 6/ is used as the external insulation and polymer film as the insulation between turns. A separate liquid cooling system is also provided. This document reports progress made in design, mechanical, dielectric, short circuit, thermal, materials, prototype, accessories, commercialization, and system studies. (DLC)

  2. Kansas BEST for Innovation 1 B.E.S.T.for Innovation

    E-Print Network [OSTI]

    for Science and Technology for Innovation #12;Kansas B.E.S.T. for Innovation 2 Acknowledgments The drafters and Technology for Innovation (Kansas B.E.S.T. for Innovation)--Kansas can capitalize on the inherent streKansas BEST for Innovation 1 KANSAS B.E.S.T.for Innovation Kansas: Building an Environment

  3. VALIDATION OF A THERMAL CONDUCTIVITY MEASUREMENT SYSTEM FOR FUEL COMPACTS

    SciTech Connect (OSTI)

    Jeff Phillips; Colby Jensen; Changhu Xing; Heng Ban

    2011-03-01T23:59:59.000Z

    A high temperature guarded-comparative-longitudinal heat flow measurement system has been built to measure the thermal conductivity of a composite nuclear fuel compact. It is a steady-state measurement device designed to operate over a temperature range of 300 K to 1200 K. No existing apparatus is currently available for obtaining the thermal conductivity of the composite fuel in a non-destructive manner due to the compact’s unique geometry and composite nature. The current system design has been adapted from ASTM E 1225. As a way to simplify the design and operation of the system, it uses a unique radiative heat sink to conduct heat away from the sample column. A finite element analysis was performed on the measurement system to analyze the associated error for various operating conditions. Optimal operational conditions have been discovered through this analysis and results are presented. Several materials have been measured by the system and results are presented for stainless steel 304, inconel 625, and 99.95% pure iron covering a range of thermal conductivities of 10 W/m*K to 70 W/m*K. A comparison of the results has been made to data from existing literature.

  4. Technology Strategy Board Driving Innovation

    E-Print Network [OSTI]

    Anderson, Jim

    six months to three years. Business partners contribute the balance of costs while reaping and innovation that will provide the inspiration and energy for UK businesses to emerge from these uncertain and profits from innovative ideas and in the longer term provides UK business with leadership and energy

  5. Green Office Program: Innovation Credits

    E-Print Network [OSTI]

    Massachusetts at Amherst, University of

    Green Office Program: Innovation Credits There are plenty of sustainable practices that aren't on our Green Office Program checklist. In an effort to encourage such practices, and reward offices Green: 5 Think outside the box, but make sure your innovation credits are approved by your Green Office

  6. QUARTIER DE L'INNOVATION

    E-Print Network [OSTI]

    Barthelat, Francois

    , but largely unknown to the public Facing sizeable urban planning challenges Comprising three of Montreal of the QI's NPO October 2013 First QI Board Meeting November 2013 Montreal Summit on Innovation on Smart Grids (Nov. 7) Implementation of key projects Montreal Summit on Innovation In Liege (Belgium

  7. Corona performance of a compact 230-kV line

    SciTech Connect (OSTI)

    Chartier, V.L.; Blair, D.E. [Bonneville Power Administration, Vancouver, WA (United States). Division of Laboratories; Easley, M.D.; Raczkowski, R.T. [Puget Sound Power and Light Co., Bellevue, WA (United States)

    1994-12-31T23:59:59.000Z

    Permitting requirements and the acquisition of new rights-of-way for transmission facilities has in recent years become increasingly difficult for most utilities, including Puget Sound Power and Light Company. In order to maintain a high degree of reliability of service while being responsive to public concerns regarding the siting of high voltage (HV) transmission facilities, Puget Power has found it necessary to more heavily rely upon the use of compact lines in franchise corridors. Compaction does, however, precipitant increased levels of audible noise (AN) and radio and TV interference (RI and TVI) due to corona on the conductors and insulator assemblies. Puget Power relies upon the Bonneville Power Administration (BPA) Corona and Field Effects computer program to calculate AN and RI for new lines. Since there was some question of the program`s ability to accurately represent quiet 230-kV compact designs, a joint project was undertaken with BPA to verify the program`s algorithms. Long-term measurements made on an operating Puget Power 230-kV compact line confirmed the accuracy of BPA`s AN model; however, the RI measurements were much lower than predicted by the BPA computer and other programs. This paper also describes how the BPA computer program can be used to calculate the voltage needed to expose insulator assemblies to the correct electric field in single test setups in HV laboratories.

  8. Corona performance of a compact 230-kV line

    SciTech Connect (OSTI)

    Chartier, V.L.; Blair, D.E. [Bonneville Power Administration, Vancouver, WA (United States). Division of Labs.] [Bonneville Power Administration, Vancouver, WA (United States). Division of Labs.; Easley, M.D.; Raczkowski, R.T. [Puget Sound Power and Light Co., Bellevue, WA (United States)] [Puget Sound Power and Light Co., Bellevue, WA (United States)

    1995-01-01T23:59:59.000Z

    Permitting requirements and the acquisition of new rights-of-way for transmission facilities has in recent years become increasingly difficult for most utilities, including Puget Sound Power and Light Company. In order to maintain a high degree of reliability of service while being responsive to public concerns regarding the siting of high voltage (HV) transmission facilities, Puget Power has found it necessary to more heavily rely upon the use of compact lines in franchise corridors. Compaction does, however, precipitate increased levels of audible noise (AN) and radio and TV interference (RI and TVI) due to corona on the conductors and insulator assemblies. Puget Power relies upon the Bonneville Power Administration (BPA) Corona and Field Effects computer program to calculate AN and RI for new lines. Since there was some question of the program`s ability to accurately represent quiet 230-kV compact designs, a joint project was undertaken with BPA to verify the program`s algorithms. Long-term measurements made on an operating Puget Power 230-kV compact line confirmed the accuracy of BPA`s AN model; however, the RI measurements were much lower than predicted by the BPA and other programs. This paper also describes how the BPA computer program can be used to calculate the voltage needed to expose insulator assemblies to the correct electric field in single test setups in HV laboratories.

  9. Ultra-compact Marx-type high-voltage generator

    DOE Patents [OSTI]

    Goerz, David A. (Brentwood, CA); Wilson, Michael J. (Modesto, CA)

    2000-01-01T23:59:59.000Z

    An ultra-compact Marx-type high-voltage generator includes individual high-performance components that are closely coupled and integrated into an extremely compact assembly. In one embodiment, a repetitively-switched, ultra-compact Marx generator includes low-profile, annular-shaped, high-voltage, ceramic capacitors with contoured edges and coplanar extended electrodes used for primary energy storage; low-profile, low-inductance, high-voltage, pressurized gas switches with compact gas envelopes suitably designed to be integrated with the annular capacitors; feed-forward, high-voltage, ceramic capacitors attached across successive switch-capacitor-switch stages to couple the necessary energy forward to sufficiently overvoltage the spark gap of the next in-line switch; optimally shaped electrodes and insulator surfaces to reduce electric field stresses in the weakest regions where dissimilar materials meet, and to spread the fields more evenly throughout the dielectric materials, allowing them to operate closer to their intrinsic breakdown levels; and uses manufacturing and assembly methods to integrate the capacitors and switches into stages that can be arranged into a low-profile Marx generator.

  10. The Cooling of Compact Stars

    E-Print Network [OSTI]

    Dany Page; Ulrich Geppert; Fridolin Weber

    2005-08-01T23:59:59.000Z

    The cooling of a compact star depends very sensitively on the state of dense matter at supranuclear densities, which essentially controls the neutrino emission, as well as on the structure of the stellar outer layers which control the photon emission. Open issues concern the hyperon population, the presence of meson condensates, superfluidity and superconductivity, and the transition of confined hadronic matter to quark matter. This paper describes these issues and presents cooling calculations based on a broad collection of equations of state for neutron star matter and strange matter. These results are tested against the body of observed cooling data.

  11. Department of Energy and Mineral Engineering Spring 2013 Solar Innovations -HVAC and Waste Stream Analysis

    E-Print Network [OSTI]

    Demirel, Melik C.

    PENNSTATE Department of Energy and Mineral Engineering Spring 2013 Solar Innovations - HVAC and Waste Stream Analysis Overview There are two problems that were voiced by Solar Innovations, HVAC system design and recycling stream improvement. The HVAC system was not providing even conditioning of office

  12. The spheromak as a compact fusion reactor

    SciTech Connect (OSTI)

    Hagenson, R.L.; Krakowski, R.A.

    1987-03-01T23:59:59.000Z

    After summarizing the economic and utility-based rationale for compact, higher-power-density fusion reactors, the gun-sustained spheromak concept is explored as one of a number of poloidal-field-dominated confinement configurations that might improve the prospects for economically attractive and operationally simplified fusion power plants. Using a comprehensive physics/engineering/costing model for the spheromak, guided by realistic engineering constraints and physics extrapolation, a range of cost-optimized reactor design points is presented, and the sensitivity of cost to key physics, engineering, and operational variables is reported. The results presented herein provide the basis for conceptual engineering designs of key fusion-power-core (FPC) subsystems and more detailed plasma modeling of this promising, high mass-power-density concept, which stresses single-piece FPC maintenance, steady-state current drive through electrostatic magnetic helicity injection, a simplified co-axial electrode-divertor, and efficient resistive-coal equilibrium-field coils. The optimal FPC size and the cost estimates project a system that competes aggressively with the best offered by alternative energy sources while simplifying considerably the complexity that has generally been associated with most approaches to magnetic fusion energy.

  13. Basement Insulation Systems - Building America Top Innovation...

    Broader source: Energy.gov (indexed) [DOE]

    about this Top Innovation. See an example of this Top Innovation in action. Find more case studies of Building America projects across the country that demonstrate advanced...

  14. Unvented, Conditioned Attics - Building America Top Innovation...

    Energy Savers [EERE]

    Read about this Top Innovation. See an example of this Top Innovation in action. Find case studies of Building America projects across the country that demonstrate unvented,...

  15. Unvented, Conditioned Crawlspaces - Building America Top Innovation...

    Energy Savers [EERE]

    about this Top Innovation. See an example of this Top Innovation in action. Find more case studies of Building America projects across the country that demonstrate unvented,...

  16. Innovative Exploration Techniques for Geothermal Assessment at...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Techniques for Geothermal Assessment at Jemez Pueblo, New Mexico Innovative Exploration Techniques for Geothermal Assessment at Jemez Pueblo, New Mexico Innovative Exploration...

  17. Environmental Mitigation Technology (Innovative System Testing...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Technology (Innovative System Testing)-Deployment and Testing of the Alden Hydropower Fish-Friendly Turbine Environmental Mitigation Technology (Innovative System...

  18. Comprehensive Energy Projects (CEP) and Innovative Financing...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Comprehensive Energy Projects (CEP) and Innovative Financing Comprehensive Energy Projects (CEP) and Innovative Financing Presented at the Technology Transition Corporation and...

  19. On Military Innovation: Toward an Analytical Framework

    E-Print Network [OSTI]

    Ross, Andrew L

    2010-01-01T23:59:59.000Z

    new The Study of Innovation and Technology in China (SITC)components of military innovation (technology, doctrine, andinnovations: robotics and information technologies for

  20. Energy Innovation Assistance Program (EIAP) (Quebec, Canada)

    Broader source: Energy.gov [DOE]

    The Energy innovation assistance program (PAIE) aims to encourage the development of new technologies or innovative processes focusing on energy efficiency or emerging energy sources by financially...

  1. Spanish Association for the Internationalisation and Innovation...

    Open Energy Info (EERE)

    Spanish Association for the Internationalisation and Innovation of Solar Companies Jump to: navigation, search Name: Spanish Association for the Internationalisation and Innovation...

  2. Energy Innovation: Green Button Initiative Empowering Americans...

    Energy Savers [EERE]

    Energy Innovation: Green Button Initiative Empowering Americans to Save Energy and Money Energy Innovation: Green Button Initiative Empowering Americans to Save Energy and Money...

  3. Grand Challenge Portfolio: Driving Innovations in Industrial...

    Broader source: Energy.gov (indexed) [DOE]

    Documents & Publications Grand Challenge Portfolio: Driving Innovations in Industrial Energy Efficiency, January 2011 - pg 8 Grand Challenge Portfolio: Driving Innovations in...

  4. Geothermal innovative technologies catalog

    SciTech Connect (OSTI)

    Kenkeremath, D. (ed.)

    1988-09-01T23:59:59.000Z

    The technology items in this report were selected on the basis of technological readiness and applicability to current technology transfer thrusts. The items include technologies that are considered to be within 2 to 3 years of being transferred. While the catalog does not profess to be entirely complete, it does represent an initial attempt at archiving innovative geothermal technologies with ample room for additions as they occur. The catalog itself is divided into five major functional areas: Exploration; Drilling, Well Completion, and Reservoir Production; Materials and Brine Chemistry; Direct Use; and Economics. Within these major divisions are sub-categories identifying specific types of technological advances: Hardware; Software; Data Base; Process/Procedure; Test Facility; and Handbook.

  5. Compacted carbon for electrochemical cells

    DOE Patents [OSTI]

    Greinke, R.A.; Lewis, I.C.

    1997-10-14T23:59:59.000Z

    This invention provides compacted carbon that is useful in the electrode of an alkali metal/carbon electrochemical cell of improved capacity selected from the group consisting of: (a) coke having the following properties: (1) an x-ray density of at least 2.00 grams per cubic centimeters, (2) a closed porosity of no greater than 5%, and (3) an open porosity of no greater than 47%; and (b) graphite having the following properties: (1) an x-ray density of at least 2.20 grams per cubic centimeters, (2) a closed porosity of no greater than 5%, and (3) an open porosity of no greater than 25%. This invention also relates to an electrode for an alkali metal/carbon electrochemical cell comprising compacted carbon as described above and a binder. This invention further provides an alkali metal/carbon electrochemical cell comprising: (a) an electrode as described above, (b) a non-aqueous electrolytic solution comprising an organic aprotic solvent and an electrolytically conductive salt and an alkali metal, and (c) a counter electrode. 10 figs.

  6. Compact submanifolds supporting singular interactions

    SciTech Connect (OSTI)

    Kaynak, Burak Tevfik, E-mail: burak.kaynak@boun.edu.tr; Teoman Turgut, O., E-mail: turgutte@boun.edu.tr

    2013-12-15T23:59:59.000Z

    A quantum particle moving under the influence of singular interactions on embedded surfaces furnish an interesting example from the spectral point of view. In these problems, the possible occurrence of a bound-state is perhaps the most important aspect. Such systems can be introduced as quadratic forms and generically they do not require renormalization. Yet an alternative path through the resolvent is also beneficial to study various properties. In the present work, we address these issues for compact surfaces embedded in a class of ambient manifolds. We discover that there is an exact bound state solution written in terms of the heat kernel of the ambient manifold for a range of coupling strengths. Moreover, we develop techniques to estimate bounds on the ground state energy when several surfaces, each of which admits a bound state solution, coexist. -- Highlights: •Schrödinger operator with singular interactions supported on compact submanifolds. •Exact bound-state solution in terms of the heat kernel of the ambient manifold. •Generalization of the variational approach to a collection of submanifolds. •Existence of a lower bound for a unique ground state energy.

  7. Hydrostatic compaction of Microtherm HT.

    SciTech Connect (OSTI)

    Broome, Scott Thomas; Bauer, Stephen J.

    2010-09-01T23:59:59.000Z

    Two samples of jacketed Microtherm{reg_sign}HT were hydrostatically pressurized to maximum pressures of 29,000 psi to evaluate both pressure-volume response and change in bulk modulus as a function of density. During testing, each of the two samples exhibited large irreversible compactive volumetric strains with only small increases in pressure; however at volumetric strains of approximately 50%, the Microtherm{reg_sign}HT stiffened noticeably at ever increasing rates. At the maximum pressure of 29,000 psi, the volumetric strains for both samples were approximately 70%. Bulk modulus, as determined from hydrostatic unload/reload loops, increased by more than two-orders of magnitude (from about 4500 psi to over 500,000 psi) from an initial material density of {approx}0.3 g/cc to a final density of {approx}1.1 g/cc. An empirical fit to the density vs. bulk modulus data is K = 492769{rho}{sup 4.6548}, where K is the bulk modulus in psi, and {rho} is the material density in g/cm{sup 3}. The porosity decreased from 88% to {approx}20% indicating that much higher pressures would be required to compact the material fully.

  8. Method for preparing porous metal hydride compacts

    DOE Patents [OSTI]

    Ron, M.; Gruen, D.M.; Mendelsohn, M.H.; Sheft, I.

    1980-01-21T23:59:59.000Z

    A method for preparing porous metallic-matrix hydride compacts which can be repeatedly hydrided and dehydrided without disintegration. A mixture of a finely divided metal hydride and a finely divided matrix metal is contacted with a poison which prevents the metal hydride from dehydriding at room temperature and atmospheric pressure. The mixture of matrix metal and poisoned metal hydride is then compacted under pressure at room temperature to form porous metallic-matrix hydride compacts.

  9. Method for preparing porous metal hydride compacts

    DOE Patents [OSTI]

    Ron, Moshe (Haifa, IL); Gruen, Dieter M. (Downers Grove, IL); Mendelsohn, Marshall H. (Woodridge, IL); Sheft, Irving (Oak Park, IL)

    1981-01-01T23:59:59.000Z

    A method for preparing porous metallic-matrix hydride compacts which can be repeatedly hydrided and dehydrided without disintegration. A mixture of a finely divided metal hydride and a finely divided matrix metal is contacted with a poison which prevents the metal hydride from dehydriding at room temperature and atmospheric pressure. The mixture of matrix metal and poisoned metal hydride is then compacted under pressure at room temperature to form porous metallic-matrix hydride compacts.

  10. Disruptive by design : the promise of the tech-enabled design competition

    E-Print Network [OSTI]

    Lorah, Katherine P. (Katherine Peterson)

    2013-01-01T23:59:59.000Z

    At their best, urban design competitions offer access to innovative design thinking for competition sponsors; high quality spaces for the benefit of the public; and career advancement for designers. However, many feel that ...

  11. Convolution type operators on locally compact groups

    E-Print Network [OSTI]

    Shtein--~erg, Convolution Type Operators on Locally Compact Groups [in Russian],. Manuscript Deposited in the All-Union Institute of Scientific and Technical ...

  12. Covered Product Category: Compact Fluorescent Lamps

    Broader source: Energy.gov [DOE]

    FEMP provides acquisition guidance across a variety of product categories, including compact fluorescent lamps (CFLs), which are an ENERGY STAR-qualified product category.

  13. Interstate Mining Compact Commission (multi-state)

    Broader source: Energy.gov [DOE]

    The Interstate Mining Compact is a multi-state governmental agency / organization that represents the natural resource and related environmental protection interests of its member states. Currently...

  14. A Comparative Approach to the Protection of Fashion Innovations

    E-Print Network [OSTI]

    Wulf, Alexander

    2007-01-01T23:59:59.000Z

    Innovation Factor: High Product Lifecycle: Short Supplier:Innovation Factor: Low Product Lifecycle: Long Market Volume

  15. It's not just about innovation

    SciTech Connect (OSTI)

    Wiley, H. S.

    2008-03-01T23:59:59.000Z

    Last year, I was one of the reviewers of proposals to a newly created NIH program, the New Innovator Award. Its goal was to address a frequent criticism – that peer review is biased against innovation – and to fund exceptionally innovative, high impact research from new investigators. To encourage the submission of innovative ideas, preliminary data was not required. Nearly 2,200 applications were submitted, but only 30 awards were made, for a success rate of <1.4%. This suggests either that there are a lot of unfunded innovative ideas out there, or that the ability to submit a proposal without preliminary data was irresistible. Over the years, I have observed that very few innovative ideas are ever brought to the point where they have made a significant impact on biological research. Grant review panels implicitly understand this unpleasant truth. The defining characteristic of successful ideas are bright and preserving scientists who believe in their ideas and are willing to do whatever it takes to make them succeed. What Thomas Edison said about genius is equally applicable to innovation; it, too, is mostly about perspiration.

  16. Phased array compaction cell for measurement of the transversely isotropic elastic properties of compacting sediments

    E-Print Network [OSTI]

    Nihei, K.T.

    2012-01-01T23:59:59.000Z

    compaction and chemical diagenesis on the microfabric andAt early stages of diagenesis, clay-rich sediments can

  17. NASA Exploration and Innovation Lead to New Discoveries Five heavyweight

    E-Print Network [OSTI]

    Waliser, Duane E.

    NASA Exploration and Innovation Lead to New Discoveries Five heavyweight lifting-body designs 1960 1961 1962 19641963 1965 1966 1967 1968 19691959 Lifting Bodies 1962-1975 Gemini 1962 disposal. Weather Satellites 1960-Present NASA launched the first Television Infrared

  18. Innovative Approach for Urban Stream Restoration Undergraduate Thesis

    E-Print Network [OSTI]

    Innovative Approach for Urban Stream Restoration Undergraduate Thesis CHBE 494 Kosta Sainis Thesis of British Columbia campus. This will restore the fish-bearing stream, which once flowed through campus Engineering #12;i EXECUTIVE SUMMARY The novelty of this study is the design of a stream which is able

  19. Compact x-ray source based on burst-mode inverse Compton scattering at 100 kHz

    E-Print Network [OSTI]

    Bessuille, J.

    A design for a compact x-ray light source (CXLS) with flux and brilliance orders of magnitude beyond existing laboratory scale sources is presented. The source is based on inverse Compton scattering of a high brightness ...

  20. Lignol Innovations, Inc. Demonstration-Scale Biorefinery

    Broader source: Energy.gov [DOE]

    The Lignol Innovations, Inc., biorefinery will produce cellulosic ethanol, high purity lignin, and furfural from hardwoods.

  1. Gene duplications, robustness and evolutionary innovations

    E-Print Network [OSTI]

    Wagner, Andreas

    , flowering plant evolution and heart development, which encompass some of the most striking innovationsGene duplications, robustness and evolutionary innovations Andreas Wagner1,2,3 Summary Mutational with evolutionary innovation is thus a special case of a general mechanism linking innovation to robustness

  2. Enterprise Innovation Institute Annual Report 2011

    E-Print Network [OSTI]

    Das, Suman

    The Enterprise Innovation Institute is headquartered at Technology Square on Georgia Tech's campus. Helped of science, technology, and innovation. During fiscal year 2011, the Enterprise Innovation Institute: 2 #12 is to help enterprises of all kinds apply sci- ence, technology, and innovation to improve their bottom lines

  3. Medical Technologies Innovation Training 2014 BIOINNOVATE FELLOWSHIP

    E-Print Network [OSTI]

    Prinz, Friedrich B.

    Medical Technologies Innovation Training 2014 BIOINNOVATE FELLOWSHIP BioInnovate Ireland is now medical technology companies and for the development of innovative medical device products. Ireland solutions to meet those needs and implement a strategy to commercialise the technology. BioInnovate

  4. Innovative Separations Technologies

    SciTech Connect (OSTI)

    J. Tripp; N. Soelberg; R. Wigeland

    2011-05-01T23:59:59.000Z

    Reprocessing used nuclear fuel (UNF) is a multi-faceted problem involving chemistry, material properties, and engineering. Technology options are available to meet a variety of processing goals. A decision about which reprocessing method is best depends significantly on the process attributes considered to be a priority. New methods of reprocessing that could provide advantages over the aqueous Plutonium Uranium Reduction Extraction (PUREX) and Uranium Extraction + (UREX+) processes, electrochemical, and other approaches are under investigation in the Fuel Cycle Research and Development (FCR&D) Separations Campaign. In an attempt to develop a revolutionary approach to UNF recycle that may have more favorable characteristics than existing technologies, five innovative separations projects have been initiated. These include: (1) Nitrogen Trifluoride for UNF Processing; (2) Reactive Fluoride Gas (SF6) for UNF Processing; (3) Dry Head-end Nitration Processing; (4) Chlorination Processing of UNF; and (5) Enhanced Oxidation/Chlorination Processing of UNF. This report provides a description of the proposed processes, explores how they fit into the Modified Open Cycle (MOC) and Full Recycle (FR) fuel cycles, and identifies performance differences when compared to 'reference' advanced aqueous and fluoride volatility separations cases. To be able to highlight the key changes to the reference case, general background on advanced aqueous solvent extraction, advanced oxidative processes (e.g., volumetric oxidation, or 'voloxidation,' which is high temperature reaction of oxide UNF with oxygen, or modified using other oxidizing and reducing gases), and fluorination and chlorination processes is provided.

  5. Cooling of Color Superconducting Compact Stars

    E-Print Network [OSTI]

    David Blaschke

    2006-03-26T23:59:59.000Z

    We review the status of research on the cooling of compact stars, with emphasis on the influence of color superconducting quark matter phases. Although a consistent microscopic approach is not yet available, severe constraints on the phase structure of matter at high densities come from recent mass and cooling observations of compact stars.

  6. The Compressor: Concurrent, Incremental, and Parallel Compaction

    E-Print Network [OSTI]

    Petrank, Erez

    The Compressor: Concurrent, Incremental, and Parallel Compaction Haim Kermany Erez Petrank Dept non-intrusive compactor is still missing. In this paper we present the Compressor, a novel compaction, thereby allowing acceptable runs on large heaps. Furthermore, the Compressor is the first compactor

  7. Exploration of Compact Stellarators as Power Plants

    E-Print Network [OSTI]

    California at San Diego, University of

    Exploration of Compact Stellarators as Power Plants: Initial Results from ARIES-CS Study Farrokh, see: http://aries.ucsd.edu/ #12;Exploration and Optimization of Compact Stellarators as Power Plants in the context of power plant studies, e.g., particle loss Divertor (location, particle and energy distribution

  8. Compacted Soil Liner Interface Strength Importance

    E-Print Network [OSTI]

    Case Study Compacted Soil Liner Interface Strength Importance Timothy D. Stark, F.ASCE1 ; Hangseok interface is not the geomembrane (GM)/compacted low-permeability soil liner (LPSL) but a soil­soil interface placing the cover soil from bottom to top. DOI: 10.1061/(ASCE)GT.1943-5606 .0000556. © 2012 American

  9. Why Python? 1) readable, compact, simple syntax

    E-Print Network [OSTI]

    Spang, Rainer

    Starting with Python #12;Why Python? 1) readable, compact, simple syntax 2) documented 3) memory output shown using green text 5 True 27 10/19/2010 6 #12;Scope · Declarations are global · Cannot for usually compacter, while more general. for - doing X for each element of S. can simulate while loops

  10. Non-compact versions of Edwards' Theorem

    E-Print Network [OSTI]

    Gogus, Nihat G; Poletsky, Evgeny A

    2010-01-01T23:59:59.000Z

    Edwards' Theorem establishes duality between a convex cone in the space of continuous functions on a compact space and the set of representing or Jensen measures for this cone. In this paper we prove non-compact versions of this theorem.

  11. Total football in innovation policy Discussion paper on the evaluation of innovation policy

    E-Print Network [OSTI]

    innovation policy can be derived. Effective innovation policy addresses the issues within the technology1 Total football in innovation policy Discussion paper on the evaluation of innovation policy Koen Schoots, Bert Daniëls, Rodrigo Rivera ECN Policy Studies The innovation climate in the Netherlands

  12. Innovative technology for contamination control in plasma processing

    SciTech Connect (OSTI)

    Selwyn, G.S.

    1994-10-01T23:59:59.000Z

    The causes and contributing factors to wafer contamination during plasma processing are discussed in the context of future technologies for controlling particle contamination by tool and process design and by the development of wafer dry cleaning technology. The importance of these developments is linked with the history of technological innovation and with the continuing evolution of the cleanroom from a highly developed facility for reducing ambient particle levels to an integrated, synergistic approach involving facilities and tooling for impeding the formation and transport of particles while also actively removing particles from sensitive surfaces. The methods, strategy and requirements for innovation in contamination control for plasma processing is discussed from a diachronic viewpoint.

  13. Compact noninvasive electron bunch-length monitor

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Roberts, B.; Mammei, R. R.; Poelker, M.; McCarter, J. L.

    2012-12-01T23:59:59.000Z

    A compact rf cavity was constructed that simultaneously resonates at many harmonic modes when excited by a repetitive bunched electron beam passing through its bore. The excitation of these modes provides a Fourier description of the temporal characteristics of the bunch train. The cavity was used to noninvasively characterize electron bunches produced from thin and thick GaAs photocathodes inside a DC high voltage photogun illuminated with 37 ps (full width half maximum, FWHM) laser pulses at repetition rates near 1500 MHz, at average beam current from 5 to 500????A , and at beam energy from 75 to 195 keV. The cavity bunch-length monitor could detect electron bunches as short as 57 ps (FWHM) when connected directly to a sampling oscilloscope, and could clearly distinguish bunches with varying degrees of space-charge induced growth and with different tail signatures. Efforts are under way to detect shorter bunches by designing cavities with increased bandwidth. This demonstration lends credibility to the idea that these cavities could also be used for other applications, including bunching and shaping, when driven with external rf.

  14. Innovation Concepts in Healthcare

    SciTech Connect (OSTI)

    None

    2011-01-06T23:59:59.000Z

    AbstractDemographic change and advances in medical science pose increased challenges to healthcare systems globally: The economic basis is aging and thus health is becoming more and more a productivity factor. At the same time, with today’s new communication possibilities the demand and expectations of effective medical treatment have been increased. This presentation will illustrate the need for the “industrialization” of healthcare in order to achieve highest results at limited budgets. Thereby, industrialization is not meaning the medical treatment based on the assembly line approach. Rather it is to recognize the cost of medical care as an investment with respective expectations on the return of the investment. Innovations in imaging and pharmaceutical products as well as in processes - that lead to similar medical results, but with lower efforts - are keys in such scenarios.BiographyProf. Dr. Hermann Requardt, 54, is a member of the Managing Board of Siemens AG and Chief Executive Officer of the Healthcare Sector. In addition he is the CTO of Siemens AG and Head of Corporate Technology, the central research department at Siemens.After completing his studies in physics and philosophy at the Darmstadt University of Technology and Johann Wolfgang Goethe University in Frankfurt and receiving a doctorate in biophysics, he worked at the Institute of Aerospace Medicine at the German Aerospace Center.In 1984 he joined the Medical Technology Group of Siemens AG, where he was responsible for projects in the Magnetic Resonance (MR) division. He was appointed head of the division in 1995. From 2001 to 2006, as a member of the Executive Management of the Medical Solutions Group, he was responsible for several areas, including technological development.In 2006 he became a Member of the Siemens’ Managing Board and head of Corporate Technology. He was additionally appointed as the Sector Healthcare CEO in 2008.Since 2006 he is an honorary professor in physics of the Johann Wolfgang Goethe University in Frankfurt.                                                                                

  15. Innovation Concepts in Healthcare

    ScienceCinema (OSTI)

    None

    2011-04-25T23:59:59.000Z

    AbstractDemographic change and advances in medical science pose increased challenges to healthcare systems globally: The economic basis is aging and thus health is becoming more and more a productivity factor. At the same time, with today?s new communication possibilities the demand and expectations of effective medical treatment have been increased. This presentation will illustrate the need for the ?industrialization? of healthcare in order to achieve highest results at limited budgets. Thereby, industrialization is not meaning the medical treatment based on the assembly line approach. Rather it is to recognize the cost of medical care as an investment with respective expectations on the return of the investment. Innovations in imaging and pharmaceutical products as well as in processes - that lead to similar medical results, but with lower efforts - are keys in such scenarios.BiographyProf. Dr. Hermann Requardt, 54, is a member of the Managing Board of Siemens AG and Chief Executive Officer of the Healthcare Sector. In addition he is the CTO of Siemens AG and Head of Corporate Technology, the central research department at Siemens.After completing his studies in physics and philosophy at the Darmstadt University of Technology and Johann Wolfgang Goethe University in Frankfurt and receiving a doctorate in biophysics, he worked at the Institute of Aerospace Medicine at the German Aerospace Center.In 1984 he joined the Medical Technology Group of Siemens AG, where he was responsible for projects in the Magnetic Resonance (MR) division. He was appointed head of the division in 1995. From 2001 to 2006, as a member of the Executive Management of the Medical Solutions Group, he was responsible for several areas, including technological development.In 2006 he became a Member of the Siemens? Managing Board and head of Corporate Technology. He was additionally appointed as the Sector Healthcare CEO in 2008.Since 2006 he is an honorary professor in physics of the Johann Wolfgang Goethe University in Frankfurt.                                                                                

  16. Innovative technologies for dredging contaminated sediments. Final report

    SciTech Connect (OSTI)

    Zappi, P.A.; Hayes, D.F.

    1991-09-01T23:59:59.000Z

    Contaminated marine sediments exist in many US waterways. Dredging is often a convenient and economical method of safely removing these sediments. However, significant concern exists over the potential environmental effects resulting from the localized sediment resuspension and contaminant release that may occur during the removal operation. This report synopsizes hydraulic equipment, pneumatic equipment, and mechanical components used for dredging and innovative modifications to their dredgeheads. It also examines previously tested dredging equipment designed to remove fine-grained sediments with a minimum amount of sediment resuspension. Major features of equipment innovations, along with available field testing information, are discussed. From these findings, the most promising innovations and research needs are identified. Since this report focuses on the dredging operations, only dredge sizes and sediment resuspension quantities are reported.

  17. Compacting Plastic-Bonded Explosive Molding Powders to Dense Solids

    SciTech Connect (OSTI)

    B. Olinger

    2005-04-15T23:59:59.000Z

    Dense solid high explosives are made by compacting plastic-bonded explosive molding powders with high pressures and temperatures for extended periods of time. The density is influenced by manufacturing processes of the powders, compaction temperature, the magnitude of compaction pressure, pressure duration, and number of repeated applications of pressure. The internal density variation of compacted explosives depends on method of compaction and the material being compacted.

  18. Modeling a Paradigm Shift: From Producer Innovation to User and Open Collaborative Innovation

    E-Print Network [OSTI]

    Baldwin, Carliss

    In this paper, we assess the economic viability of innovation by producers relative to two increasingly important alternative models: innovations by single-user individuals or firms and open collaborative innovation. We ...

  19. INNOVATION EDUCATION EXCELLENCE DISTILLATIONS

    E-Print Network [OSTI]

    Chan, Hue Sun

    more efficient solar energy devices. It turns out it could also help to design the next revolution of this work. Vy Dong and her students have devised ways to make double ring compounds. Mark Lautens and his that emit differ- ent colours depending on which DNA strand is pres- ent. Deborah Zamble's and Mark Nitz

  20. Compact, electro-hydraulic, variable valve actuation system providing...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Compact, electro-hydraulic, variable valve actuation system providing variable lift, timing and duration to enable high efficiency engine combustion control Compact,...

  1. Versatile and compact capacitive dilatometer

    SciTech Connect (OSTI)

    Schmiedeshoff, G. M.; Lounsbury, A. W.; Luna, D. J.; Tracy, S. J.; Schramm, A. J.; Tozer, S. W.; Correa, V. F.; Hannahs, S. T.; Murphy, T. P.; Palm, E. C.; Lacerda, A. H.; Bud'ko, S. L.; Canfield, P. C.; Smith, J. L.; Lashley, J. C.; Cooley, J. C. [Department of Physics, Occidental College, Los Angeles, California 90041 (United States); National High Magnetic Field Laboratory, Florida State University, Tallahassee, Florida 32310 (United States); Ames Laboratory, Iowa State University, Ames, Iowa 50011 and Department of Physics and Astronomy, Iowa State University, Ames, Iowa 50011 (United States); Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States)

    2006-12-15T23:59:59.000Z

    We describe the design, construction, calibration, and operation of a relatively simple differential capacitive dilatometer suitable for measurements of thermal expansion and magnetostriction from 300 to below 1 K with a low-temperature resolution of about 0.05 A ring . The design is characterized by an open architecture permitting measurements on small samples with a variety of shapes. Dilatometers of this design have operated successfully with a commercial physical property measurement system, with several types of cryogenic refrigeration systems, in vacuum, in helium exchange gas, and while immersed in liquid helium (magnetostriction only) to temperatures of 30 mK and in magnetic fields to 45 T.

  2. 2014 Housing Innovation Awards DOE Challenge Home Application...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Housing Innovation Awards DOE Challenge Home Application 2014 Housing Innovation Awards DOE Challenge Home Application The U.S. Department of Energy's Housing Innovation Awards...

  3. Building America Top Innovations Hall of Fame Profile - Building...

    Energy Savers [EERE]

    Top Innovations Hall of Fame Profile - Building America's Top Innovations Propel the Home Building Industry toward Higher Performance Building America Top Innovations Hall of Fame...

  4. Compact collimated fiber optic array diagnostic for railgun plasma experiments

    SciTech Connect (OSTI)

    Tang, V; Solberg, J; Ferriera, T; Tully, L; Stephan, P

    2008-10-02T23:59:59.000Z

    We have developed and tested a compact collimated sixteen channel fiber optic array diagnostic for studying the light emission of railgun armature plasmas with {approx}mm spatial and sub-{micro}s temporal resolution. The design and operational details of the diagnostic are described. Plasma velocities, oscillation, and dimension data from the diagnostic for the Livermore Fixed Hybrid Armature experiment are presented and compared with 1-D simulations. The techniques and principles discussed allow the extension of the diagnostic to other railgun and related dense plasma experiments.

  5. Diffusion Welding of Compact Heat Exchangers for Nuclear Applications

    SciTech Connect (OSTI)

    Denis Clark; Ron Mizia; Dr. Michael V. Glazoff; Mr. Michael W. Patterson

    2012-06-01T23:59:59.000Z

    The next-­-generation nuclear plant (NGNP) is designed to be a flexible source of energy, producing various mixes of electrical energy and process heat (for example, for hydrogen generation) on demand. Compact heat exchangers provide an attractive way to move energy from the helium primary reactor coolant to process heat uses. For process heat efficiency, reactor outlet temperatures of 750-­-900°C are desirable. There are minor but deleterious components in the primary coolant; the number of alloys that can handle this environment is small. The present work concentrates on Alloys 800H and 617.

  6. Controlled powder morphology experiments in megabar 304 stainless steel compaction

    SciTech Connect (OSTI)

    Staudhammer, K.P.; Johnson, K.A.

    1985-01-01T23:59:59.000Z

    Experiments with controlled morphology including shape, size, and size distribution were made on 304L stainless steel powders. These experiments involved not only the powder variables but pressure variables of 0.08 to 1.0 Mbar. Also included are measured container strain on the material ranging from 1.5% to 26%. Using a new strain controllable design it was possible to seperate and control, independently, strain and pressure. Results indicate that powder morphology, size distribution, packing density are among the pertinent parameters in predicting compaction of these powders.

  7. A CMOS-compatible compact display

    E-Print Network [OSTI]

    Chen, Andrew R. (Andrew Raymond)

    2005-01-01T23:59:59.000Z

    Portable information devices demand displays with high resolution and high image quality that are increasingly compact and energy-efficient. Microdisplays consisting of a silicon CMOS backplane integrated with light ...

  8. Steady state compact toroidal plasma production

    DOE Patents [OSTI]

    Turner, William C. (Livermore, CA)

    1986-01-01T23:59:59.000Z

    Apparatus and method for maintaining steady state compact toroidal plasmas. A compact toroidal plasma is formed by a magnetized coaxial plasma gun and held in close proximity to the gun electrodes by applied magnetic fields or magnetic fields produced by image currents in conducting walls. Voltage supply means maintains a constant potential across the electrodes producing an increasing magnetic helicity which drives the plasma away from a minimum energy state. The plasma globally relaxes to a new minimum energy state, conserving helicity according to Taylor's relaxation hypothesis, and injecting net helicity into the core of the compact toroidal plasma. Controlling the voltage so as to inject net helicity at a predetermined rate based on dissipative processes maintains or increases the compact toroidal plasma in a time averaged steady state mode.

  9. Gravitational waves from merging compact binaries

    E-Print Network [OSTI]

    Hughes, Scott A.

    Largely motivated by the development of highly sensitive gravitational-wave detectors, our understanding of merging compact binaries and the gravitational waves they generate has improved dramatically in recent years. ...

  10. Southern States Energy Compact (Multiple States)

    Broader source: Energy.gov [DOE]

    The Southern States Energy Compact provides for the proper employment and conservation of energy, and for the employment of energy-related facilities, materials, and products, within the context of...

  11. Belle Fourche River Compact (South Dakota)

    Broader source: Energy.gov [DOE]

    The Belle Fourche River Compact, agreed to by South Dakota and Wyoming, seeks to provide for the most efficient use of the waters of the Belle Fourche River Basin for multiple purposes, and to...

  12. A Compact Parallel-plane Perpendicular-current Feed for a Modified Equiangular Spiral Antenna and Related Circuits

    E-Print Network [OSTI]

    Eubanks, Travis Wayne

    2011-08-08T23:59:59.000Z

    for the designed antennas and circuits. iv To my anc ee, Amanda Marie Stebbins v ACKNOWLEDGMENTS Thank you, Mr. Li, for your ever-present willingness to help. You contributed greatly to the initial design and fabrication of the compact spiral. Dr. Nevels, your... to fabricate each three-layer compact spiral, the spiral array fed by DSPSL lines is left for future research. A circular monopole antenna was designed as an alternate array element which may be equally suited for DSPSL array design using the described power...

  13. When innovativeness in form matters: the joint impact of form innovativeness and expected innovativeness type on product evaluations over time 

    E-Print Network [OSTI]

    Kroff, Michael William

    2007-09-17T23:59:59.000Z

    Past research in the area of product innovativeness has been dominated by studies conducted at the firm level. Furthermore, these studies principally lack a consumer perspective on the product innovativeness - product ...

  14. Measuring the U.S.-China Innovation Gap: Initial Findings of the UCSD-Tsinghua Innovation Metrics Survey Project

    E-Print Network [OSTI]

    2013-01-01T23:59:59.000Z

    STUDY OF INNOVATION AND TECHNOLOGY IN CHINA POLICY BRIEF STIThe Study of Innovation and Technology in China (SITC) is aof Science, Technology, and Innovation: Interim Report,”

  15. Compact reflective imaging spectrometer utilizing immersed gratings

    DOE Patents [OSTI]

    Chrisp, Michael P. (Danville, CA)

    2006-05-09T23:59:59.000Z

    A compact imaging spectrometer comprising an entrance slit for directing light, a first mirror that receives said light and reflects said light, an immersive diffraction grating that diffracts said light, a second mirror that focuses said light, and a detector array that receives said focused light. The compact imaging spectrometer can be utilized for remote sensing imaging spectrometers where size and weight are of primary importance.

  16. Compact binary mergers: an astrophysical perspective

    E-Print Network [OSTI]

    S. Rosswog

    2010-12-22T23:59:59.000Z

    This paper reviews the current understanding of double neutron star and neutron star black hole binaries. It addresses mainly (nuclear) astrophysics aspects of compact binary mergers and thus complements recent reviews that have emphasized the numerical relativity viewpoint. In particular, the paper discusses different channels to release neutron-rich matter into the host galaxy, connections between compact binary mergers and short Gamma-ray bursts and accompanying electromagnetic signals.

  17. Disruptive Innovation in Numerical Hydrodynamics

    SciTech Connect (OSTI)

    Waltz, Jacob I. [Los Alamos National Laboratory

    2012-09-06T23:59:59.000Z

    We propose the research and development of a high-fidelity hydrodynamic algorithm for tetrahedral meshes that will lead to a disruptive innovation in the numerical modeling of Laboratory problems. Our proposed innovation has the potential to reduce turnaround time by orders of magnitude relative to Advanced Simulation and Computing (ASC) codes; reduce simulation setup costs by millions of dollars per year; and effectively leverage Graphics Processing Unit (GPU) and future Exascale computing hardware. If successful, this work will lead to a dramatic leap forward in the Laboratory's quest for a predictive simulation capability.

  18. Commercialization and Innovation Fact Sheet

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625govInstrumentstdmadapInactiveVisiting theCommercialization and Innovation The Commercialization and Innovation

  19. Technology Selections for Cylindrical Compact Fabrication

    SciTech Connect (OSTI)

    Jeffrey A. Phillips

    2010-10-01T23:59:59.000Z

    A variety of process approaches are available and have been used historically for manufacture of cylindrical fuel compacts. The jet milling, fluid bed overcoating, and hot press compacting approach being adopted in the U.S. AGR Fuel Development Program for scale-up of the compacting process involves significant paradigm shifts from historical approaches. New methods are being pursued because of distinct advantages in simplicity, yield, and elimination of process mixed waste. Recent advances in jet milling technology allow simplified dry matrix powder preparation. The matrix preparation method is well matched with patented fluid bed powder overcoating technology recently developed for the pharmaceutical industry and directly usable for high density fuel particle matrix overcoating. High density overcoating places fuel particles as close as possible to their final position in the compact and is matched with hot press compacting which fully fluidizes matrix resin to achieve die fill at low compacting pressures and without matrix end caps. Overall the revised methodology provides a simpler process that should provide very high yields, improve homogeneity, further reduce defect fractions, eliminate intermediate grading and QC steps, and allow further increases in fuel packing fractions.

  20. Energy Design Assistance Project Tracker - 2014 BTO Peer Review...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    project also includes compiling and disseminating data about the cost effectiveness of net zero energy (NZE) buildings that use innovative technologies and design approaches. By...

  1. SAFETY ASSESSMENT OF THE ARIES COMPACT STELLARATOR DESIGN

    E-Print Network [OSTI]

    California at San Diego, University of

    -CS by report- ing radiological inventories, decay heat, and radioactive waste management optionsARIES-CS and the facility can meet the no-evacuation requirement. KEYWORDS: ARIES-CS, safety assessment, stellarator Note In this paper we examine the safety and environmen- tal performance of ARIES-CS by reporting radiological

  2. Compact thermal modeling for package design with practical power maps

    E-Print Network [OSTI]

    Liu, Zao; Tan, Sheldon; Hua, Yingbo; Wang, Hai; Gupta, Ashish

    2014-01-01T23:59:59.000Z

    response temp (Celsius) Y kjk Reference temp. Identifiedmodel X kþ1 A B C D X k U kjk 3.2. Persistently excitingxðk þ 1Þ; …; xðk þ N2Þ; U kjk ?½uðkÞ; uðk þ 1Þ; …; uðk þ

  3. A Review of the Reflector Compact Fluorescent Lights Technology Procurement Program: Conclusions and Results

    SciTech Connect (OSTI)

    Sandahl, Linda J.; Gilbride, Theresa L.; Ledbetter, Marc R.; McCullough, Jeffrey J.

    2008-05-19T23:59:59.000Z

    This report describes a project sponsored by the U.S. Department of Energy (DOE) and implemented by the Pacific Northwest National Laboratory (PNNL), from 2000 to 2007 to improve the performance of reflector type (R-lamp) compact fluorescent lamps (CFLs) and increase their availability throughout the United States by means of a technology development and procurement strategy. In 2000, at the request of the U.S. Department of Energy’s Emerging Technologies Program and its predecessors, the Pacific Northwest National Laboratory undertook a technology procurement seeking R-CFLs that were specifically designed for use in ICAT recessed can fixtures and that met other minimum performance criteria including minimum light output and size restrictions (to ensure they fit in standard residential recessed cans). The technology procurement included two phases. In Phase I, requests for proposals (RFPs) were issued in October 2002 and five manufacturers responded with 12 lamp models. Eight of these models met the minimum requirements and passed the 6-hour short-term test in a simulated ICAT environment. These eight models were subjected to long-term tests of 6,000 or more hours in a simulated ICAT environment. Three of these models passed the short- and long-term tests and were promoted through the program website (www.pnl.gov/rlamps), press releases, and fliers. To increase the number of qualifying models, a second RFP was issued in June 2005. In April 2007, DOE announced that 16 reflector CFL (R-CFL) models by four manufacturers had met all the minimum requirements of Phase 2 of the R-CFL Technology Innovation Competition. PNNL developed both the criteria and the test apparatus design for Elevated Temperature Life Testing (ETLT), which has been included by DOE in its draft ENERGY STAR specifications for the reflector category of CFLs. PNNL promoted the winning lamps through a program website, press releases, and fliers as well as through program partners. PNNL also helped engage distributors including Costco, the Home Depot, Bonneville Power Administration, and utility organizations.

  4. Essays on innovation, productivity, and talent allocation

    E-Print Network [OSTI]

    Shu, Pian

    2012-01-01T23:59:59.000Z

    This thesis contains three essays on innovation, productivity, and talent allocation. The first essay explores a novel channel through which short-term economic fluctuations affect the long-term innovative output of the ...

  5. OKLAHOMA STATE UNIVERSITY CENTER FOR INNOVATION AND

    E-Print Network [OSTI]

    Veiga, Pedro Manuel Barbosa

    OKLAHOMA STATE UNIVERSITY CENTER FOR INNOVATION AND ECONOMIC DEVELOPMENT, INC. June 30, 2010 #12;OKLAHOMA STATE UNIVERSITY CENTER FOR INNOVATION AND ECONOMIC DEVELOPMENT, INC. June 30, 2010 Audited Standards ...........20 #12;Independent Auditors' Report Board of Regents Oklahoma Agricultural

  6. OKLAHOMA STATE UNIVERSITY CENTER FOR INNOVATION AND

    E-Print Network [OSTI]

    Veiga, Pedro Manuel Barbosa

    OKLAHOMA STATE UNIVERSITY CENTER FOR INNOVATION AND ECONOMIC DEVELOPMENT, INC. June 30, 2011 #12;OKLAHOMA STATE UNIVERSITY CENTER FOR INNOVATION AND ECONOMIC DEVELOPMENT, INC. June 30, 2011 Standards ...........18 #12; 1 Independent Auditors' Report Board of Regents Oklahoma Agricultural

  7. OKLAHOMA STATE UNIVERSITY CENTER FOR INNOVATION AND

    E-Print Network [OSTI]

    Veiga, Pedro Manuel Barbosa

    OKLAHOMA STATE UNIVERSITY CENTER FOR INNOVATION AND ECONOMIC DEVELOPMENT, INC. June 30, 2009 #12;OKLAHOMA STATE UNIVERSITY CENTER FOR INNOVATION AND ECONOMIC DEVELOPMENT, INC. June 30, 2009 Audited Standards ...........20 #12;Independent Auditors' Report Board of Regents Oklahoma Agricultural

  8. Soil Quality Information Sheet Rangeland Soil Quality--Compaction

    E-Print Network [OSTI]

    Soil Quality Information Sheet Rangeland Soil Quality--Compaction USDA, Natural Resources Conservation Service May 2001 Rangeland Sheet 4 What is compaction? Soil compaction occurs when moist or wet soil aggregates are pressed together and the pore space between them is reduced. Compaction changes

  9. Compact Proof Certificates For Linear Logic Kaustuv Chaudhuri

    E-Print Network [OSTI]

    Chaudhuri, Kaustuv

    Compact Proof Certificates For Linear Logic Kaustuv Chaudhuri INRIA, France http://kaustuv.chaudhuri

  10. Technology Innovation Program Guidelines and Documentation

    E-Print Network [OSTI]

    Magee, Joseph W.

    #12;Technology Innovation Program Guidelines and Documentation Requirements for Research Involving ............................................................................ 5 F. Required Documentation.............................................................................. 16 D. Required Documentation

  11. Introducing Kyoto University Tradition, Innovation

    E-Print Network [OSTI]

    Takada, Shoji

    in the historical city of Kyoto in 1897, Kyoto University is the second oldest research university in Japan. Today and Development Kyoto University's Mission Statement declares its intention to sustain and develop its historical, and a unique balance is achieved between tradition and innovation. While preserving its rich cultural heritage

  12. City of Tallahassee Innovative Energy Initiatives

    SciTech Connect (OSTI)

    Wilder, Todd; Moragne, Corliss L.

    2014-06-25T23:59:59.000Z

    The City of Tallahassee's Innovative Energy Initiatives program sought, first, to evaluate customer response and acceptance to in-home Smart Meter-enabled technologies that allow customers intelligent control of their energy usage. Additionally, this project is in furtherance of the City of Tallahassee's ongoing efforts to expand and enhance the City's Smart Grid capacity and give consumers more tools with which to effectively manage their energy consumption. This enhancement would become possible by establishing an "operations or command center" environment that would be designed as a dual use facility for the City's employees - field and network staff - and systems responsible for a Smart Grid network. A command center would also support the City's Office of Electric Delivery and Energy Reliability's objective to overcome barriers to the deployment of new technologies that will ensure a truly modern and robust grid capable of meeting the demands of the 2151 century.

  13. Overview and Analysis of the Japanese and US Innovation SystemsUS Innovation Systems

    E-Print Network [OSTI]

    Innovation System (NIS or National System of Innovation) as the flow of technology and information among theory, innovation and technology d l t lt f l t f l ti hi t idevelopment are results of a complex set based on "IT substitution for manufacturing technology"Former innovation system based on IT substitution

  14. NAC Technology and Innovation Committee Meeting Report

    E-Print Network [OSTI]

    Christian, Eric

    NAC Technology and Innovation Committee Meeting Report Esther Dyson Chair, NAC Technology and Innovation Committee August 6, 2010 0 #12;Technology and Innovation Agenda Aug. 3rd Meeting · OCT Update ­ R programs ­ P. Desai · OCT/ESMD Technology Coordination ­ J. Reuther · Overview of ESMD New Technology

  15. Edinburgh Research Explorer Agile Business Model Innovation

    E-Print Network [OSTI]

    Millar, Andrew J.

    Edinburgh Research Explorer Agile Business Model Innovation Citation for published version: Bock, A & Gerard, G 2014, 'Agile Business Model Innovation' The European Business Review, vol May - June 2014. Link Publisher Rights Statement: © Bock, A., & Gerard, G. (2014). Agile Business Model Innovation. The European

  16. Web Technologies for Open Innovation Darko Jesic

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Web Technologies for Open Innovation Darko Jesic Université Paris-Dauphine, DRM, Mlab Place du on the application of the Web technologies in the open innovation model. We analyze technologies for expert search of different open innovation paradigms in the function of Web technologies that serve for their realization

  17. Corporate Venture Capital (CVC) Seeking Innovation and

    E-Print Network [OSTI]

    , Technology Innovation Program, National Institute of Standards and Technology #12;Corporate Venture Capital, Deputy Director Technology Innovation Program Marc G. Stanley, Director #12;ii Acknowledgments T his policymakers in the role of corporate venture capital (CVC) in technology innovation. The research included

  18. Ris-R-1582(EN) Innovation Process

    E-Print Network [OSTI]

    Risø-R-1582(EN) Innovation Process By Andrei Kolodovski for Risø Risø National Laboratory Roskilde Denmark December 2006 #12;Author: Andrei Kolodovski for Risø Title: Innovation Process Department: Risø system - Report provides innovation methodology to establish common understanding of the process concepts

  19. Compact fluorescent lamp using horizontal and vertical insulating septums and convective venting geometry

    DOE Patents [OSTI]

    Siminovitch, M.

    1998-02-10T23:59:59.000Z

    A novel design is described for a compact fluorescent lamp, including a lamp geometry which will increase light output and efficacy of the lamp in a base down operating position by providing horizontal and vertical insulating septums positioned in the ballast compartment of the lamp to provide a cooler coldspot. Selective convective venting provides additional cooling of the ballast compartment. 9 figs.

  20. Compact cryogenic Kerr microscope for time-resolved studies of electron spin transport in microstructures

    E-Print Network [OSTI]

    van der Wal, Caspar H.

    Compact cryogenic Kerr microscope for time-resolved studies of electron spin transport with 1 m spatial resolution. The microscope was designed to study spin transport, a critical issue-temperature optical microscope, elec- tromagnet and cryogenic cell with cold finger to measure continuous-wave cw

  1. Energy Innovation Hubs: A Home for Scientific Collaboration

    SciTech Connect (OSTI)

    Chu, Steven

    2012-01-01T23:59:59.000Z

    Secretary Chu will host a live, streaming Q&A session with the directors of the Energy Innovation Hubs on Tuesday, March 6, at 2:15 p.m. EST. The directors will be available for questions regarding their teams' work and the future of American energy. Ask your questions in the comments below, or submit them on Facebook, Twitter (@energy), or send an e-mail to newmedia@hq.doe.gov, prior or during the live event. Dr. Hank Foley is the director of the Greater Philadelphia Innovation Cluster for Energy-Efficient Buildings, which is pioneering new data intensive techniques for designing and operating energy efficient buildings, including advanced computer modeling. Dr. Douglas Kothe is the director of the Consortium for Advanced Simulation of Light Water Reactors, which uses powerful supercomputers to create "virtual" reactors that will help improve the safety and performance of both existing and new nuclear reactors. Dr. Nathan Lewis is the director of the Joint Center for Artificial Photosynthesis, which focuses on how to produce fuels from sunlight, water, and carbon dioxide. The Energy Innovation Hubs are major integrated research centers, with researchers from many different institutions and technical backgrounds. Each hub is focused on a specific high priority goal, rapidly accelerating scientific discoveries and shortening the path from laboratory innovation to technological development and commercial deployment of critical energy technologies. Ask your questions in the comments below, or submit them on Facebook, Twitter (@energy), or send an e-mail to newmedia@energy.gov, prior or during the live event. The Energy Innovation Hubs are major integrated research centers, with researchers from many different institutions and technical backgrounds. Each Hub is focused on a specific high priority goal, rapidly accelerating scientific discoveries and shortening the path from laboratory innovation to technological development and commercial deployment of critical energy technologies. Dr. Hank Holey is the director of the Greater Philadelphia Innovation Cluster for Energy-Efficient Buildings, which is pioneering new data intensive techniques for designing and operating energy efficient buildings, including advanced computer modeling. Dr. Douglas Kothe is the director of the Modeling and Simulation for Nuclear Reactors Hub, which uses powerful supercomputers to create "virtual" reactors that will help improve the safety and performance of both existing and new nuclear reactors. Dr. Nathan Lewis is the director of the Joint Center for Artificial Photosynthesis Hub, which focuses on how to produce biofuels from sunlight, water, and carbon dioxide.

  2. Energy Innovation Hubs: A Home for Scientific Collaboration

    ScienceCinema (OSTI)

    Chu, Steven

    2013-05-29T23:59:59.000Z

    Secretary Chu will host a live, streaming Q&A session with the directors of the Energy Innovation Hubs on Tuesday, March 6, at 2:15 p.m. EST. The directors will be available for questions regarding their teams' work and the future of American energy. Ask your questions in the comments below, or submit them on Facebook, Twitter (@energy), or send an e-mail to newmedia@hq.doe.gov, prior or during the live event. Dr. Hank Foley is the director of the Greater Philadelphia Innovation Cluster for Energy-Efficient Buildings, which is pioneering new data intensive techniques for designing and operating energy efficient buildings, including advanced computer modeling. Dr. Douglas Kothe is the director of the Consortium for Advanced Simulation of Light Water Reactors, which uses powerful supercomputers to create "virtual" reactors that will help improve the safety and performance of both existing and new nuclear reactors. Dr. Nathan Lewis is the director of the Joint Center for Artificial Photosynthesis, which focuses on how to produce fuels from sunlight, water, and carbon dioxide. The Energy Innovation Hubs are major integrated research centers, with researchers from many different institutions and technical backgrounds. Each hub is focused on a specific high priority goal, rapidly accelerating scientific discoveries and shortening the path from laboratory innovation to technological development and commercial deployment of critical energy technologies. Ask your questions in the comments below, or submit them on Facebook, Twitter (@energy), or send an e-mail to newmedia@energy.gov, prior or during the live event. The Energy Innovation Hubs are major integrated research centers, with researchers from many different institutions and technical backgrounds. Each Hub is focused on a specific high priority goal, rapidly accelerating scientific discoveries and shortening the path from laboratory innovation to technological development and commercial deployment of critical energy technologies. Dr. Hank Holey is the director of the Greater Philadelphia Innovation Cluster for Energy-Efficient Buildings, which is pioneering new data intensive techniques for designing and operating energy efficient buildings, including advanced computer modeling. Dr. Douglas Kothe is the director of the Modeling and Simulation for Nuclear Reactors Hub, which uses powerful supercomputers to create "virtual" reactors that will help improve the safety and performance of both existing and new nuclear reactors. Dr. Nathan Lewis is the director of the Joint Center for Artificial Photosynthesis Hub, which focuses on how to produce biofuels from sunlight, water, and carbon dioxide.

  3. Road Design Susan Handy

    E-Print Network [OSTI]

    Handy, Susan L.

    conditions for non-motorized street users." - ITE Subcommittee on Traffic Calming #12;Speed Control Measures design · Traffic control (if we have time) #12;Level Agencies Primary concern Roles Federal FHWA FTA;Innovations/Trends · Traffic Calming · Skinny Streets · Road Diets · Complete Streets · Green Streets

  4. Cylindrically Symmetric Models of Anisotropic Compact Stars

    E-Print Network [OSTI]

    G. Abbas; Sumara Nazeer; M. A. Meraj

    2014-12-16T23:59:59.000Z

    In this paper we have discussed the possibility of forming anisotropic compact stars from cosmological constant as one of the competent candidates of dark energy with cylindrical symmetry. For this purpose, we have applied the analytical solution of Krori and Barua metric to a particular cylindrically symmetric spacetime. The unknown constants in Krori and Barua metric have been determined by using masses and radii of class of compact stars like 4$U$1820-30, Her X-1, SAX J 1808-3658. The properties of these stars have been analyzed in detail. In this setting the cosmological constant has been taken as a variable which depends on the radial coordinates. We have checked all the regularity conditions, stability and surface redshift of the compact stars 4$U$1820-30, Her X-1, SAX J 1808-3658.

  5. Innovative technology summary report.

    SciTech Connect (OSTI)

    NONE

    2006-05-09T23:59:59.000Z

    Traditional site characterization methods rely on preplanned sampling programs and off-site analysis of samples to determine the extent and level of hazardous waste contamination. This process is costly and time-consuming. Static work plans specify the numbers and locations of samples to be collected, as well as the analyses to be performed on collected samples. Sampling crews are mobilized, samples are collected, and the crews are demobilized before final results become available. Additional sampling programs are often required to resolve uncertainties raised by the initial sampling and analysis results. The drawbacks of a traditional approach to sampling program design and execution are high costs per sample, pressure to over sample while at the site, and inevitable surprises in the analytical results that require additional sampling to resolve. A key step in the characterization of hazardous wastes at U.S. Department of Energy (DOE) sites is determination of the extent of contamination. The proper number and placement of sampling locations is required to both minimize characterization costs and guarantee that contamination extent can be estimated with reasonable confidence. Because ''soft'' information (i.e., historical records, computer modeling results, past experience, etc.) for a site are usually just as important as ''hard'' laboratory results, the approach taken must include a quantitative way of accounting for both hard and soft site data. An alternative to traditional sampling programs is Adaptive Sampling and Analysis Programs (ASAPs). ASAPs rely on field analytical methods to generate sample results quickly enough to have an impact on the course of the sampling program. Rather than a static work plan, ASAPs are based on dynamic work plans that specify the logic for how sampling numbers, locations, and analyses will be determined as the program proceeds. To ensure that the sampling stays on track, ASAPs also rely on rapid, field-level decision making. ASAPs require (1) field analytical methods that are appropriate for the types of expected contaminants and media present at the site, and (2) a way of supporting decision making in the field that is appropriate for the goals of the program.

  6. Innovative Rates Program. Final report

    SciTech Connect (OSTI)

    Not Available

    1982-06-21T23:59:59.000Z

    Title II of the Energy Conservation and Production Act (ECPA) as amended by the Public Utility Regulatory Policies Act (PURPA) provided financial assistance to state utility regulatory commissions, nonregulated electric utilities, and the Tennessee Valley Authority through the Innovative Rates Program. The financial assistance was to be used to plan or carry out electric utility regulatory rate reform initiatives relating to innovative rate structures that encourage conservation of energy, electric utility efficiency and reduced costs, and equitable rates to consumers. The Federal and local objectives of the project are described. Activities planned and accomplishments are summarized for the following: project management, data collection, utility bill evaluation, billing enclosure/mailing evaluation, media program evaluation, display evaluation, rate study sessions evaluation, speakers bureau evaluation, and individual customer contacts. A timetable/milestone chart and financial information are included. (MHR)

  7. Innovative financing survey: Final report

    SciTech Connect (OSTI)

    Garrison, R.L.

    1986-06-06T23:59:59.000Z

    This report represents the current knowledge and utilization of Innovative Financing techniques of Weatherization Assistance Program (WAP) subgrantees, a sample of Institutional Conservation Program (ICP) grantees, Public Service Commissions (PSC) and selected utilities broadly distributed in the country. The survey inquired essentially about their organizational use and familiarity with the following innovative financing methods: Direct Loan, Loan Interest Reduction, Lease, Lease Purchase, Shared Savings, Energy Service Contracts, Conservation Incentives and Guaranteed Cash Flow. Whatever their characteristics, urban or rural, schools or hospitals, gas and electric utilities of differing ownership types, large or small states, respondents indicated a marginal awareness and utilization of the eight major financing methods. Even though their awareness and use is uneven with respect to their characteristics, certain trends emerge which display an overall lack of application of most of these financing techniques to enhance the program use of grant funds.

  8. Remote vacuum compaction of compressible hazardous waste

    DOE Patents [OSTI]

    Coyne, M.J.; Fiscus, G.M.; Sammel, A.G.

    1998-10-06T23:59:59.000Z

    A system is described for remote vacuum compaction and containment of low-level radioactive or hazardous waste comprising a vacuum source, a sealable first flexible container, and a sealable outer flexible container for receiving one or more first flexible containers. A method for compacting low level radioactive or hazardous waste materials at the point of generation comprising the steps of sealing the waste in a first flexible container, sealing one or more first containers within an outer flexible container, breaching the integrity of the first containers, evacuating the air from the inner and outer containers, and sealing the outer container shut. 8 figs.

  9. Remote vacuum compaction of compressible hazardous waste

    DOE Patents [OSTI]

    Coyne, Martin J. (Pittsburgh, PA); Fiscus, Gregory M. (McMurray, PA); Sammel, Alfred G. (Pittsburgh, PA)

    1998-01-01T23:59:59.000Z

    A system for remote vacuum compaction and containment of low-level radioactive or hazardous waste comprising a vacuum source, a sealable first flexible container, and a sealable outer flexible container for receiving one or more first flexible containers. A method for compacting low level radioactive or hazardous waste materials at the point of generation comprising the steps of sealing the waste in a first flexible container, sealing one or more first containers within an outer flexible container, breaching the integrity of the first containers, evacuating the air from the inner and outer containers, and sealing the outer container shut.

  10. COMPACT ACCELERATOR CONCEPT FOR PROTON THERAPY

    SciTech Connect (OSTI)

    Caporaso, G; Sampayan, S; Chen, Y; Harris, J; Hawkins, S; Holmes, C; Krogh, M; Nelson, S; Nunnally, W; Paul, A; Poole, B; Rhodes, M; Sanders, D; Selenes, K; Sullivan, J; Wang, L; Watson, J

    2006-08-18T23:59:59.000Z

    A new type of compact induction accelerator is under development at the Lawrence Livermore National Laboratory that promises to increase the average accelerating gradient by at least an order of magnitude over that of existing induction machines. The machine is based on the use of high gradient vacuum insulators, advanced dielectric materials and switches and is being developed as a compact flash x-ray radiography source. Research describing an extreme variant of this technology aimed at proton therapy for cancer will be presented.

  11. SimWeb IST-2001-34651 Exploring Innovative eBusiness Models

    E-Print Network [OSTI]

    López-Sánchez, Maite

    SimWeb IST-2001-34651 Exploring Innovative eBusiness Models using Multi Agent Simulation Document Name: MASDT Design Specification Document Date: Febraury 4th, 2004 Document Owner: SimWeb Consortium. In particular, this document corresponds to deliverable "D34.2 MASDT Design Specification" . Keyword List: SimWeb

  12. Silver Peak Innovative Exploration Project

    Broader source: Energy.gov [DOE]

    DOE Geothermal Peer Review 2010 - Presentation. Project objectives: Reduce the high level of risk during the early stages of geothermal project development by conducting a multi-faceted and innovative exploration and drilling program at Silver Peak. Determine the combination of techniques that are most useful and cost-effective in identifying the geothermal resource through a detailed, post-project evaluation of the exploration and drilling program.

  13. Innovative Utility Pricing for Industry

    E-Print Network [OSTI]

    Ross, J. A.

    tariffs can re a market for power during the time when it has sult in benefits to industry, to the electric abundant capacity available. From the other rate utility, and to other ratepayers on the electric payers' perspective, there will be a continued...INNOVATIVE UTILITY PRICING FOR INDUSTRY James A. Ross Drazen-Brubaker &Associates, Inc. St. Louis, Missouri ABSTRACT The electric utility industry represents only one source of power available to industry. Al though the monopolistic...

  14. Nanostructured Photovoltaics: - Energy Innovation Portal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What's Possible for Renewable Energy: GridTruckNanostructued Glass-CeramicInnovationSolar Photovoltaic

  15. Innovation investment area: Technology summary

    SciTech Connect (OSTI)

    Not Available

    1994-03-01T23:59:59.000Z

    The mission of Environmental Management`s (EM) Office of Technology Development (OTD) Innovation Investment Area is to identify and provide development support for two types of technologies that are developed to characterize, treat and dispose of DOE waste, and to remediate contaminated sites. They are: technologies that show promise to address specific EM needs, but require proof-of-principle experimentation; and (2) already proven technologies in other fields that require critical path experimentation to demonstrate feasibility for adaptation to specific EM needs. The underlying strategy is to ensure that private industry, other Federal Agencies, universities, and DOE National Laboratories are major participants in developing and deploying new and emerging technologies. To this end, about 125 different new and emerging technologies are being developed through Innovation Investment Area`s (IIA) two program elements: RDDT&E New Initiatives (RD01) and Interagency Agreements (RD02). Both of these activities are intended to foster research and development partnerships so as to introduce innovative technologies into other OTD program elements for expedited evaluation.

  16. IEEE TRANSACTIONS ON VERY LARGE SCALE INTEGRATION (VLSI) SYSTEMS, VOL. 14, NO. 5, MAY 2006 501 HotSpot: A Compact Thermal Modeling Methodology

    E-Print Network [OSTI]

    Skadron, Kevin

    -chip interconnect self-heating power and thermal model such that the thermal impacts on interconnects can also computationally efficient. Index Terms--Compact thermal model, early design stages, in- terconnect self-heating

  17. Fusion Engineering and Design 81 (2006) 11591168 Major integration issues in evolving the configuration design

    E-Print Network [OSTI]

    Raffray, A. René

    2006-01-01T23:59:59.000Z

    the configuration design space for the ARIES-CS compact stellarator power plant A.R. Raffraya,, S. Malangb, L. El an attractive power plant concept based on a compact stellarator configuration. The first phase of the study and the irregular cross-section of the plasma and in-reactor components. Earlier stellarator power plant studies led

  18. Cold compaction study of Armstrong Process Ti-6Al-4V powders

    SciTech Connect (OSTI)

    Chen, Wei [ORNL; Yamamoto, Yukinori [ORNL; Peter, William H [ORNL; Gorti, Sarma B [ORNL; Sabau, Adrian S [ORNL; Clark, Michael B [ORNL; Nunn, Stephen D [ORNL; Kiggans, Jim [ORNL; Blue, Craig A [ORNL; Fuller, Brian [International Titanium Powder; Akhtar, Kamal [International Titanium Powder

    2011-01-01T23:59:59.000Z

    This work investigates the cold compaction behavior of Ti-6Al-4V powders produced by Armstrong Process . As-received as well as milled powders were characterized and these powders were uniaxially die-pressed at designated pressures up to 690 MPa to form disk samples with different aspect ratios. Samples with high aspect ratio exhibited non-uniform density along the pressing axis and the density distribution is in consistent with the result predicted by finite element analysis. The linear regression analysis on the experimental density data can be used to predict density of compacts with different aspect ratios. In the studied pressure range, an empirical powder compaction equation represents the green density pressure relationship very well for both the as-received and 1-hr milled Armstrong Ti-6Al-4V powders.

  19. Measure Guideline: Implementing a Plenum Truss for a Compact Air Distribution System

    SciTech Connect (OSTI)

    Burdick, A.

    2013-10-01T23:59:59.000Z

    This Measure Guideline presents the steps to implement a compact duct system inside an attic bulkhead (plenum truss) of a one-story, slab-on-grade (SOG) home. In a compact duct design, ductwork runs are reduced in length to yield a smaller and more compact duct system. Less energy will be lost through ductwork if the ducts are contained within the thermal enclosure of the house. These measures are intended for the production builder working to meet the 2012 International Energy Conservation Code (IECC) requirements and keep the ductwork within the thermal enclosure of the house. This measure of bringing the heating, ventilation and air conditioning (HVAC) equipment and ductwork within the thermal enclosure of the house is appropriate for the builder wishing to avoid cathedralizing the insulation in the attic space (i.e., locating it at the underside of the roof deck rather than along the attic floor) or adding dropped soffits.

  20. Systems Analysis of a Compact Next Step Burning Plasma Experiment

    SciTech Connect (OSTI)

    S.C. Jardin; C.E. Kessel; D. Meade; C. Neumeyer

    2002-02-06T23:59:59.000Z

    A new burning plasma systems code (BPSC) has been developed for analysis of a next step compact burning plasma experiment with copper-alloy magnet technology. We consider two classes of configurations: Type A, with the toroidal field (TF) coils and ohmic heating (OH) coils unlinked, and Type B, with the TF and OH coils linked. We obtain curves of the minimizing major radius as a function of aspect ratio R(A) for each configuration type for typical parameters. These curves represent, to first order, cost minimizing curves, assuming that device cost is a function of major radius. The Type B curves always lie below the Type A curves for the same physics parameters, indicating that they lead to a more compact design. This follows from that fact that a high fraction of the inner region, r < R-a, contains electrical conductor material. However, the fact that the Type A OH and TF magnets are not linked presents fewer engineering challenges and should lead to a more reliable design. Both the Type A and Type B curves have a minimum in major radius R at a minimizing aspect ratio A typically above 2.8 and at high values of magnetic field B above 10 T. The minimizing A occurs at larger values for longer pulse and higher performance devices. The larger A and higher B design points also have the feature that the ratio of the discharge time to the current redistribution time is largest so that steady-state operation can be more realistically prototyped. A sensitivity study is presented for the baseline Type A configuration showing the dependence of the results on the parameters held fixed for the minimization study.

  1. Preferential Path Profiling: Compactly Numbering Interesting Paths

    E-Print Network [OSTI]

    Chilimbi, Trishul

    preferential path profiling (PPP), that reduces the overhead of path profiling. PPP leverages the observation that most consumers of path profiles are only inter- ested in a subset of all program paths. PPP achieves produced by PPP. This compact path numbering enables our PPP implementation to record path information

  2. Compact range for variable-zone measurements

    DOE Patents [OSTI]

    Burnside, Walter D. (Columbus, OH); Rudduck, Roger C. (Columbus, OH); Yu, Jiunn S. (Albuquerque, NM)

    1988-01-01T23:59:59.000Z

    A compact range for testing antennas or radar targets includes a source for directing energy along a feedline toward a parabolic reflector. The reflected wave is a spherical wave with a radius dependent on the distance of the source from the focal point of the reflector.

  3. Compact Ultradense Objects in the Solar System

    E-Print Network [OSTI]

    J. Rafelski; Ch. Dietl; L. Labun

    2013-03-19T23:59:59.000Z

    We describe properties and gravitational interactions of meteor-mass and greater compact ultra dense objects with nuclear density or greater (CUDO s). We discuss possible enclosure of CUDO s in comets, stability of these objects on impact with the Earth and Sun and show that the hypothesis of a CUDO core helps resolve issues challenging the understanding of a few selected cometary impacts.

  4. A Global Compact to End Poverty

    E-Print Network [OSTI]

    A Global Compact to End Poverty Jeffrey Sachs on stabilisation, transition and weapons of mass progress. We can realistically envision a world without extreme poverty by the year 2025 because. Sachs, The End of Poverty, 2005. WORLD ECONOMICS · Vol. 6 · No. 4 · October­December 2005 11 Jeffrey D

  5. Pathway to a Compact SASE FEL Device

    E-Print Network [OSTI]

    Dattoli, G; Petrillo, V; Rau, J V; Sabia, E; Spassovsky, I; Biedron, S G; Einstein, J; Milton, S V

    2015-01-01T23:59:59.000Z

    Newly developed high peak power lasers have opened the possibilities of driving coherent light sources operating with laser plasma accelerated beams and wave undulators. We speculate on the combination of these two concepts and show that the merging of the underlying technologies could lead to new and interesting possibilities to achieve truly compact, coherent radiator devices.

  6. Innovate in China, Innovate for China | GE Global Research

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of Science (SC) EnvironmentalGyroSolé(tm)HydrogenRFPTri-PartyFor manyInhibitingInnovate in China,

  7. Compact low resolution spectrograph, an imaging and long slit spectrograph for robotic telescopes

    SciTech Connect (OSTI)

    Rabaza, O., E-mail: ovidio@ugr.es [Department of Civil Engineering, University of Granada, Severo Ochoa Str. s/n, 18071 Granada (Spain); Institute of Astrophysics of Andalucía (CSIC), Glorieta de la Astronomía s/n, 18008 Granada (Spain); Jelinek, M.; Cunniffe, R.; Ruedas-Sánchez, J. [Institute of Astrophysics of Andalucía (CSIC), Glorieta de la Astronomía s/n, 18008 Granada (Spain)] [Institute of Astrophysics of Andalucía (CSIC), Glorieta de la Astronomía s/n, 18008 Granada (Spain); Castro-Tirado, A. J. [Institute of Astrophysics of Andalucía (CSIC), Glorieta de la Astronomía s/n, 18008 Granada (Spain) [Institute of Astrophysics of Andalucía (CSIC), Glorieta de la Astronomía s/n, 18008 Granada (Spain); Department of Systems and Automatic Engineering, University of Málaga, 29071 Málaga (Spain); Zeman, J. [Astronomical Institute of the Academic of Sciences, Fricova 298, 25165 Ondrejov (Czech Republic)] [Astronomical Institute of the Academic of Sciences, Fricova 298, 25165 Ondrejov (Czech Republic); Hudec, R. [Astronomical Institute of the Academic of Sciences, Fricova 298, 25165 Ondrejov (Czech Republic) [Astronomical Institute of the Academic of Sciences, Fricova 298, 25165 Ondrejov (Czech Republic); Faculty of Electrical Engineering, Czech Technical University, Technicka 2, Praha 6 (Czech Republic); Sabau-Graziati, L. [National Institute of Aerospace Technology, Carretera de Ajalvir, 28850 Madrid (Spain)] [National Institute of Aerospace Technology, Carretera de Ajalvir, 28850 Madrid (Spain)

    2013-11-15T23:59:59.000Z

    The COmpact LOw REsolution Spectrograph (COLORES) is a compact and lightweight (13 kg) f/8 imaging spectrograph designed for robotic telescopes, now installed and operating on the TELMA, a rapid-slewing 60 cm telescope of the BOOTES-2 observatory in Málaga (Spain). COLORES is a multi-mode instrument that enables the observer to seamlessly switch between low-dispersion spectroscopy and direct imaging modes during an observation. In this paper, we describe the instrument and its development, from the initial scientific requirements through the optical design process to final configuration with theoretical performance calculations. The mechanical and electronic design is described, methods of calibration are discussed and early laboratory and scientific results are shown.

  8. Southeast Interstate Low-Level Radioactive Waste Management Compact (multi-state)

    Broader source: Energy.gov [DOE]

    The Southeast Interstate Low-Level Radioactive Waste Management Compact is administered by the Compact Commission. The Compact provides for rotating responsibility for the region's low-level...

  9. Energy Management Through Innovative Rates

    E-Print Network [OSTI]

    Williams, M. L.

    1982-01-01T23:59:59.000Z

    of energy efficiency in the industrial sector and specific rate design alternatives for doing so....

  10. Production, Cost, and Soil Compaction Estimates for Two Western Juniper

    E-Print Network [OSTI]

    Dodson, Beth

    , Crook County Soil and Water Conservation District, Prineville, OR 97754. ABSTRACT: Harvesting trialsProduction, Cost, and Soil Compaction Estimates for Two Western Juniper Extraction Systems, production rates, and soil compaction impacts of two systems for harvesting western juniper (Juniperus

  11. Fundamental building blocks for a compact optoelectronic neural network processor

    E-Print Network [OSTI]

    Ruedlinger, Benjamin Franklin, 1976-

    2003-01-01T23:59:59.000Z

    The focus of this thesis is interconnects within the Compact Optoelectronic Neural Network Processor. The goal of the Compact Optoelectronic Neural Network Processor Project (CONNPP) is to build a small, rugged neural ...

  12. A thermodynamic approach for compaction of asphaltic composites

    E-Print Network [OSTI]

    Koneru, Saradhi

    2009-05-15T23:59:59.000Z

    and Focus of Current Work . . . . . . . . . . . . . . 2 B. Outline of the Thesis . . . . . . . . . . . . . . . . . . . . . 3 C. Notations Used . . . . . . . . . . . . . . . . . . . . . . . . 4 II LITERATURE REVIEW... . . . . . . . . . . . . . . . . 8 b. Asphalt Binder . . . . . . . . . . . . . . . . . . . 8 C. Compaction Equipment . . . . . . . . . . . . . . . . . . . . 9 1. Field Compaction Equipment . . . . . . . . . . . . . . 9 a. Static Steel Wheel Rollers . . . . . . . . . . . . . 9 b...

  13. A Natural Experiment on Innovation Without Patents

    E-Print Network [OSTI]

    Torrance, Andrew W.

    2015-05-07T23:59:59.000Z

    experiment to take place in which innovation may operate without interference from new patent rights. Far from a desire to foster user and open innovation in human-related biotechnology, the primary rationale for this amendment to the Patent Act was strong... repugnance to biological research leading to, and the possibility of resultant ownership interests in, inventions involving human beings. Rather, it is incidental that this natural experiment may provide valuable insight into how patents affect innovation...

  14. Accelerating digital health innovation : analyzing opportunities in the healthcare innovation ecosystem

    E-Print Network [OSTI]

    Cohen, Elliot, M.B.A. Massachusetts Institute of Technology

    2013-01-01T23:59:59.000Z

    There has recently been a dramatic increase in demand for healthcare innovation. In this thesis we present a framework for analyzing a digital health innovation ecosystem in the US. Our framework consists of four key ...

  15. Process Innovation by working miners : a case of user innovation in copper mining industry

    E-Print Network [OSTI]

    Burdiles Orellana, Sergio

    2012-01-01T23:59:59.000Z

    Employees are known to develop and use key process improvements. In this thesis, I explore innovation by mining employees working in Codelco, a Chilean mining company. The data on these innovations come from a contest ...

  16. New product development methods : a study of open design

    E-Print Network [OSTI]

    Smith, Ariadne G. (Ariadne Geneviève)

    2012-01-01T23:59:59.000Z

    This thesis explores the application of open design to the process of developing physical products. Open design is a type of decentralized innovation that is derived from applying principles of open source software and ...

  17. A study of compaction methods for lunar soil simulants

    E-Print Network [OSTI]

    Ekkad, Rama Varadarajan

    1993-01-01T23:59:59.000Z

    , compaction by vibration, compaction under vacuum pressure under the simultaneous effect of vibration are examined. Duc to the increasing confining pressure, the air voids decrease and the particles will be more closely packed, thus increasing the relative... density. The research will be used to identify a convenient method for compacting samples for laboratory digging experiments. The results of the research conclude that compaction by using vacuum and vibration produce results which can be used to predict...

  18. Live with the Energy Innovation Hub Directors

    Broader source: Energy.gov [DOE]

    Tune in today, Tuesday, March 6, 2012, at 2:15pm EST for a live discussion with our three Energy Innovation Hubs directors.

  19. Vapor Retarder Classification - Building America Top Innovation...

    Energy Savers [EERE]

    the Top Innovation. See an example of vapor retarder best practices in action. Find other case studies of Building America projects across the country that utilizes vapor retarder...

  20. Innovative Manufacturing Initiative Recognition Day, Advanced...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Publications Innovative Manufacturing Initiative Recognition Day Advanced Manufacturing Office Overview Unlocking the Potential of Additive Manufacturing in the Fuel Cells Industry...

  1. Scientific Innovation Through Integration Capabilities Series

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Innovation Through Integration Capabilities Series www.emsl.pnnl.gov EMSL offers technologically sophisticated microscopy instruments capable of imaging a variety of sample types...

  2. Manufacturing serendipity: Chicago Innovation Exchange enhancing...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Social Media Photos Videos Fact Sheets, Brochures and Reports Summer Science Writing Internship John Flavin, Executive Director of the Chicago Innovation Exchange, started a small...

  3. Innovative Mercury Treatment Benefits Stream, Fish | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Mercury Treatment Benefits Stream, Fish Innovative Mercury Treatment Benefits Stream, Fish October 1, 2012 - 12:00pm Addthis Oak Ridge scientists Kelly Roy, left, and Trent Jett...

  4. Detachment Faulting and Geothermal Resources - An Innovative...

    Open Energy Info (EERE)

    Resources - An Innovative Integrated Geological and Geophysical Investigation in Fish Lake Valley, Nevada Geothermal Project Jump to: navigation, search Last modified on...

  5. Sandia National Laboratories: Advanced Manufacturing Innovation...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Innovation Initiative Sandia Participated in AMII to Support American-Made Wind-Turbine Blades On December 3, 2014, in Computational Modeling & Simulation, Energy, Materials...

  6. CHEVROLET | ELECTRIC | GREEN | SPARK EV | TECHNOLOGY. INNOVATION...

    Open Energy Info (EERE)

    CHEVROLET | ELECTRIC | GREEN | SPARK EV | TECHNOLOGY. INNOVATION & SOLUTIONS | GREENER VEHICLES Home There are currently no posts in this category. Syndicate content...

  7. Innovation Impact: Breakthrough Research Results (Brochure)

    SciTech Connect (OSTI)

    Not Available

    2013-07-01T23:59:59.000Z

    The Innovation Impact brochure captures key breakthrough results across NREL's primary areas of renewable energy and energy efficiency research: solar, wind, bioenergy, transportation, buildings, analysis, and manufacturing technologies.

  8. Webinar: Leadership Recognition with Housing Innovation Awards

    Broader source: Energy.gov [DOE]

    Title: Leadership Recognition with Housing Innovation Awards             Date: Wednesday, May 21, 2014Time: 12:00PM - 1:00 PM EST

  9. Efficiency Exchange Conference Highlights Energy Efficiency Innovation...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Efficiency Exchange Conference Highlights Energy Efficiency Innovations and Trends Northwest electric power industry connects on the latest energy efficiency programs and...

  10. Innovative Drivetrains in Electric Automotive Technology Education...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Merit Review 2014: Innovative Drivetrains in Electric Automotive Technology Education (IDEATE) Center for Electric Drive Transportation at the University of Michigan - Dearborn...

  11. Validation of Innovative Exploration Technologies for Newberry...

    Open Energy Info (EERE)

    Validation of Innovative Exploration Technologies for Newberry Volcano Geothermal Project Jump to: navigation, search Last modified on July 22, 2011. Project Title Validation of...

  12. Efficiency Exchange highlights energy efficiency innovations...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Efficiency Exchange highlights energy efficiency innovations and trends Northwest electric power industry connects on the latest energy efficiency programs and strategies Portland,...

  13. Grand Challenge Portfolio: Driving Innovations in Industrial...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    9 Grand Challenge Portfolio: Driving Innovations in Industrial Energy Efficiency, January 2011 - pg 9 grandchallengesportfoliopg9.pdf More Documents & Publications Grand...

  14. Grand Challenge Portfolio: Driving Innovations in Industrial...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    6 Grand Challenge Portfolio: Driving Innovations in Industrial Energy Efficiency, January 2011 - pg 6 grandchallengesportfoliopg6.pdf More Documents & Publications Grand...

  15. Grand Challenge Portfolio: Driving Innovations in Industrial...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    8 Grand Challenge Portfolio: Driving Innovations in Industrial Energy Efficiency, January 2011 - pg 8 grandchallengesportfoliopg8.pdf More Documents & Publications Grand...

  16. Electrolysis - Hydrogen - Energy Innovation Portal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power AdministrationField Campaign:INEAWater UseC Supports - Energy InnovationVehicles and Fuels

  17. Moisture Barrier - Energy Innovation Portal

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHighandSWPA / SPRA /Ml'. WilliamEnergy Innovation PortalNEPTUNESolar

  18. Manufacturing Innovation in the DOE

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the.pdfBreaking ofOil & Gas »ofMarketingSmartManufacturing Innovation in the DOE

  19. Innovative Topics for Advanced Biofuels

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the.pdfBreaking of BlytheDepartment ofEnergy InformationSavings for AirlineInnovative

  20. Top Innovative Science of 2013

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of ScienceandMesa del SolStrengthening a solidSynthesisAppliances » Top Innovative Science of 2013

  1. Top Ten Innovations of 2013

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of ScienceandMesa del SolStrengthening a solidSynthesisAppliances » Top Innovative Science of 2013

  2. Energy Innovations | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnualPropertyd8c-a9ae-f8521cbb8489 No revision|LLC Place: Ketchum,SPARQL SPARQL OpenEI'sInnovations

  3. Innovation

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directed off Energy.gov.Energy02.pdf7 OPAM

  4. Innovative Electromagnetic Sensors for Pipeline Crawlers

    SciTech Connect (OSTI)

    J. Bruce Nestleroth

    2006-05-04T23:59:59.000Z

    Internal inspection of pipelines is an important tool for ensuring safe and reliable delivery of fossil energy products. Current inspection systems that are propelled through the pipeline by the product flow cannot be used to inspect all pipelines because of the various physical barriers they encounter. Recent development efforts include a new generation of powered inspection platforms that crawl slowly inside a pipeline and are able to maneuver past the physical barriers that can limit inspection. At Battelle, innovative electromagnetic sensors are being designed and tested for these new pipeline crawlers. The various sensor types can be used to assess a wide range of pipeline anomalies including corrosion, mechanical damage, and cracks. Battelle is in the final year on a projected three-year development effort. In the first year, two innovative electromagnetic inspection technologies were designed and tested. Both were based on moving high-strength permanent magnets to generate inspection energy. One system involved translating permanent magnets towards the pipe. A pulse of electric current would be induced in the pipe to oppose the magnetization according to Lenz's Law. The decay of this pulse would indicate the presence of defects in the pipe wall. This inspection method is similar to pulsed eddy current inspection methods, with the fundamental difference being the manner in which the current is generated. Details of this development effort were reported in the first semiannual report on this project. The second inspection methodology is based on rotating permanent magnets. The rotating exciter unit produces strong eddy currents in the pipe wall. At distances of a pipe diameter or more from the rotating exciter, the currents flow circumferentially. These circumferential currents are deflected by pipeline defects such as corrosion and axially aligned cracks. Simple sensors are used to detect the change in current densities in the pipe wall. The second semiannual report on this project reported on experimental and modeling results. The results showed that the rotating system was more adaptable to pipeline inspection and therefore only this system will be carried into the second year of the sensor development. In the third reporting period, the rotating system inspection was further developed. Since this is a new inspection modality without published fundamentals to build upon, basic analytical and experimental investigations were performed. A closed form equation for designing rotating exciters and positioning sensors was derived from fundamental principles. Also signal processing methods were investigated for detection and assessment of pipeline anomalies. A lock in amplifier approach was chosen as the method for detecting the signals. Finally, mechanical implementations for passing tight restrictions such as plug valves were investigated. This inspection concept is new and unique; a United States patent application has been submitted. In this reporting period, a general design of the rotating permanent magnet inspection system is presented. The rotating permanent magnet inspection system is feasible for pipes ranging in diameter from 8 to 18 inches using a two pole configuration. Experimental results and theoretical calculations provide the basis for selection of the critical design parameters. The parameters include a significant magnet to pipe separation that will facilitate the passage of pipeline features. With the basic values of critical components established, the next step is a detailed mechanical design of a pipeline ready inspection system.

  5. 24 BONEZone Spring 2007 Innovation enables organizations to effectively compete

    E-Print Network [OSTI]

    Kusiak, Andrew

    . Some use the terms "technology-based innovation" or "technological innovation" to emphasize the role of technology. Innovation Level The level of innovation varies from incremental to radical. Incremental24 BONEZone · Spring 2007 Innovation enables organizations to effectively compete (Christensen 1997

  6. Beam shaping element for compact fiber injection systems

    SciTech Connect (OSTI)

    Weichman, L.S.; Dickey, F.M.; Shagam, R.N.

    2000-01-05T23:59:59.000Z

    Injection of high power, multi-mode laser profiles into a fiber optic delivery system requires controlling a number of injection parameters to maximize throughput and minimize concerns for optical damage both at the entrance and exit faces of the fiber optic. A simple method for simultaneously achieving a compact fiber injection geometry and control of these injection parameters, independent of the input source characteristics, is provided by a refractive lenslet array and simple injection lens configuration. Design criteria together with analytical and experimental results for the refractive lenslet array and short focal length injection lens are presented. This arrangement provides a uniform spatial intensity distribution at the fiber injection plane to a large degree independent of the source mode structure, spatial profile, divergence, size, and/or alignment to the injection system. This technique has application to a number of laser systems where uniform illumination of a target or remote delivery of high peak power is desired.

  7. Innovation Project Development Jan 2013 1 Attributes of an Innovation Project

    E-Print Network [OSTI]

    Bertini, Robert L.

    Innovation Project Development Jan 2013 1 Attributes of an Innovation Project Good projects the idea to act on the problem or opportunity To achieve the goals of the project, the team must, computers, materials and instrumentation. The cash award from the Innovation Council is most often used

  8. CIRP Design Conference 2009 Integrated Design and PLM Applications in Aeronautics Product Development

    E-Print Network [OSTI]

    Boyer, Edmond

    CIRP Design Conference 2009 Integrated Design and PLM Applications in Aeronautics Product and development costs, could be reached thanks to innovative design methods supported by PLM technologies and cooperation between the project partners. The paper proposes a survey on integrated design methods and PLM

  9. Innovative Energy Efficient Industrial Ventilation

    E-Print Network [OSTI]

    Litomisky, A.

    2005-01-01T23:59:59.000Z

    factories, we found striking dichotomy between the classical “static” design of ventilation systems and constantly changing workflow and business demands. Using data from real factories, we are able to prove that classical industrial ventilation design...

  10. A laboratory investigation of vibratory compaction of dry soils

    E-Print Network [OSTI]

    Webster, Cecil Ray

    1984-01-01T23:59:59.000Z

    . Standard Compaction Curve for Soil 3 (CL) 48 49 50 53 54 56 25 Effect of Frequency Variation on the Time Required to Achieve I/2 inch (12. 7 mm) of Settlement 57 26. Foot Size Effects on Compaction of Various Soils 59 27. Effect of Frequency... on the Compaction of Soil 1 (SP) Using Two Different Feet 63 28. Effect of Frequency on the Compaction of Soil 1 (SP) Using the Semi-Circular Foot with Various Static Weights 64 29. Effect of Frequency on the Compaction of Soil 1 (SP) Using the 5 Inch Diameter...

  11. Compact x-ray source and panel

    DOE Patents [OSTI]

    Sampayon, Stephen E. (Manteca, CA)

    2008-02-12T23:59:59.000Z

    A compact, self-contained x-ray source, and a compact x-ray source panel having a plurality of such x-ray sources arranged in a preferably broad-area pixelized array. Each x-ray source includes an electron source for producing an electron beam, an x-ray conversion target, and a multilayer insulator separating the electron source and the x-ray conversion target from each other. The multi-layer insulator preferably has a cylindrical configuration with a plurality of alternating insulator and conductor layers surrounding an acceleration channel leading from the electron source to the x-ray conversion target. A power source is connected to each x-ray source of the array to produce an accelerating gradient between the electron source and x-ray conversion target in any one or more of the x-ray sources independent of other x-ray sources in the array, so as to accelerate an electron beam towards the x-ray conversion target. The multilayer insulator enables relatively short separation distances between the electron source and the x-ray conversion target so that a thin panel is possible for compactness. This is due to the ability of the plurality of alternating insulator and conductor layers of the multilayer insulators to resist surface flashover when sufficiently high acceleration energies necessary for x-ray generation are supplied by the power source to the x-ray sources.

  12. The compactness of presupernova stellar cores

    SciTech Connect (OSTI)

    Sukhbold, Tuguldur; Woosley, S. E., E-mail: sukhbold@ucolick.org [Department of Astronomy and Astrophysics, University of California, Santa Cruz, CA 95064 (United States)

    2014-03-01T23:59:59.000Z

    The success or failure of the neutrino-transport mechanism for producing a supernova in an evolved massive star is known to be sensitive not only to the mass of the iron core that collapses, but also to the density gradient in the silicon and oxygen shells surrounding that core. Here we study the systematics of a presupernova core's 'compactness' as a function of the mass of the star and the physics used in its calculation. Fine-meshed surveys of presupernova evolution are calculated for stars from 15 to 65 M {sub ?}. The metallicity and the efficiency of semiconvection and overshoot mixing are both varied and bare carbon-oxygen cores are explored as well as full hydrogenic stars. Two different codes, KEPLER and MESA, are used for the study. A complex interplay of carbon and oxygen burning, especially in shells, can cause rapid variations in the compactness for stars of very nearly the same mass. On larger scales, the distribution of compactness with main sequence mass is found to be robustly non-monotonic, implying islands of 'explodabilty,' particularly around 8-20 M {sub ?} and 25-30 M {sub ?}. The carbon-oxygen (CO) core mass of a presupernova star is a better, (though still ambiguous) discriminant of its core structure than the main sequence mass.

  13. The Evolution of Compact Binary Star Systems

    E-Print Network [OSTI]

    Konstantin Postnov; Lev Yungelson

    2014-03-21T23:59:59.000Z

    We review the formation and evolution of compact binary stars consisting of white dwarfs (WDs), neutron stars (NSs), and black holes (BHs). Mergings of compact binary stars are expected to be the most important sources for the forthcoming gravitational-wave (GW) astronomy. In the first part of the review, we discuss observational manifestations of close binary stars with NS and/or black components and their merger rate, crucial points in the formation and evolution of compact stars in binary systems, including the treatment of the natal kicks which NSs and BHs acquire during the core collapse of massive stars and the common envelope phase of binary evolution, which are most relevant to the merging rates of NS-NS, NS-BH and BH-BH binaries. The second part of the review is devoted mainly to formation and evolution of binary WDs and their observational manifestations, including their role as progenitors of cosmologically important thermonuclear SN Ia. We also consider AM CVn-stars which are thought to be the best verification binary GW sources for future low-frequency GW space interferometers.

  14. Policy Transfer of Innovative Sustainability Principles and Practices

    E-Print Network [OSTI]

    Policy Transfer of Innovative Sustainability Principles and Practices: The Whistler, British) Report No.: 574 Title of Thesis: Policy transfer of innovative sustainability principles and practices;v Abstract This study examines how innovative policies that seek to embed sustainability principles

  15. Innovative Learning Technology Initiative W.S. Hodgkiss

    E-Print Network [OSTI]

    Gleeson, Joseph G.

    Innovative Learning Technology Initiative (ILTI) W.S. Hodgkiss AVC Academic Personnel and Resources 29 October 2013 #12;Innovative Learning Technology Initiative (ILTI) · Established January 2013-16) #12;Innovative Learning Technology Initiative (ILTI) · Components · Courses and Course Components Goal

  16. Frameworks for Analyzing Chinese Defense and Military Innovation

    E-Print Network [OSTI]

    Cheung, Tai Ming; Mahnken, Thomas G; Ross, Andrew L

    2011-01-01T23:59:59.000Z

    on the Study of Innovation and Technology in China (SITC),The Study of Innovation and Technology in China (SITC) is a1) the components of innovation: technology, doctrine, and

  17. Advancing healthcare technology through insight, innovation, and leadership

    E-Print Network [OSTI]

    Soloveichik, David

    Advancing healthcare technology through insight, innovation, and leadership Master of Translational medical technologies and improving healthcare delivery? Successful medical innovation requires more than of medical innovators. Applications are open to engineers, scientists, and clinicians with a passion

  18. INNOVATION IN EDUCATION AWARDS Request for Proposals 2015

    E-Print Network [OSTI]

    Sibille, Etienne

    innovative approaches that utilize proven or emerging technologies. Examples of these technology#12;INNOVATION IN EDUCATION AWARDS Request for Proposals 2015 Submission Deadline: Monday, January different departments, units, and campuses on the development of innovative approaches to teaching Develop

  19. White Papers Submitted to the Technology Innovation Program

    E-Print Network [OSTI]

    Magee, Joseph W.

    White Papers Submitted to the Technology Innovation Program The Technology Innovation Program (TIP) at the National Institute of Standards and Technology was established laboratories and nonprofit research institutions, to support, promote, and accelerate innovation in the U

  20. US DOE Housing Innovation Awards | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Housing Innovation Awards recognize the very best in innovation on the path to zero net-energy ready homes. You are invited to attend the Housing Innovation Awards, presented...

  1. Strategic Partnership for Sustainable Energy Innovation

    E-Print Network [OSTI]

    : Sustainable energy solutions independent of nuclear energy Highly qualified innovators that will be global-utilisation: biofuels from flue gases Source to use biomass value chain optimisation Platform 3: energy Intelligence International Communities: Access to partners from the local to the global level 4. InnOVATIOn Strategic

  2. The IIT Innovators Fueling Big Ideas

    E-Print Network [OSTI]

    Saniie, Jafar

    Making things work. The IIT Innovators Fueling Big Ideas Winter 2012 John P. Calamos sr. Bold Thinking The PlanT How the Zero-Waste System Works researCh Neutron Detection, Dinosaur Collagen, Big Data in our next wave of innovators and leaders, some of whom are featured in this issue. Our students have

  3. Technology Innovation Honoring Students, Faculty, and Staff

    E-Print Network [OSTI]

    Chapman, Michael S.

    2012 Technology Innovation Awards Honoring Students, Faculty, and Staff for their Dedication Portland, Oregon Sponsored by: #12;2012 Technology Innovation Awards WELCOME & AWARDS REMARKS Andrew R.O. Watson, PhD, CLP Interim Director, Technology Transfer Technology Transfer and Business Development

  4. Managing Innovation: A Multidisciplinary Scenario Development Approach

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    prescribed innovation methods, inovation is as much about a social process and context as it is a systematic process, thus making it somewhat naturalistic in character [3,4]. How does one manage innovation used for military planning and by the petrochemical industry [6]. Scenarios allow information

  5. Environnement dstabilis, innovation de gestion et exprimentations.

    E-Print Network [OSTI]

    Boyer, Edmond

    ici et lon illustre par létude dun cas le fait quune innovation en matière doutil de gestion ou1 Environnement déstabilisé, innovation de gestion et expérimentations. Proposition d'un cadre conceptuel et application à un cas clinique. Lucien Véran. Professeur. Université Paul Cézanne ­ Euromed

  6. Innovative grout/retrieval demonstration final report

    SciTech Connect (OSTI)

    Loomis, G.G.; Thompson, D.N.

    1995-01-01T23:59:59.000Z

    This report presents the results of an evaluation of an innovative retrieval technique for buried transuranic waste. Application of this retrieval technique was originally designed for full pit retrieval; however, it applies equally to a hot spot retrieval technology. The technique involves grouting the buried soil waste matrix with a jet grouting procedure, applying an expansive demolition grout to the matrix, and retrieving the debris. The grouted matrix provides an agglomeration of fine soil particles and contaminants resulting in an inherent contamination control during the dusty retrieval process. A full-scale field demonstration of this retrieval technique was performed on a simulated waste pit at the Idaho National Engineering Laboratory. Details are reported on all phases of this proof-of-concept demonstration including pit construction, jet grouting activities, application of the demolition grout, and actual retrieval of the grouted pit. A quantitative evaluation of aerosolized soils and rare earth tracer spread is given for all phases of the demonstration, and these results are compared to a baseline retrieval activity using conventional retrieval means. 8 refs., 47 figs., 10 tabs.

  7. MIT System Design and Management Program

    E-Print Network [OSTI]

    de Weck, Olivier L.

    , disseminating, and preserving knowledge, and to working with others to bring this knowledge to bear on the worldMIT System Design and Management Program MIT System Design and Management Program Leadership, innovation, systems thinking #12;MIT System Design and Management Program #12;about MIT The mission of MIT

  8. Comparative analysis of compact heat exchangers for application as the intermediate heat exchanger for advanced nuclear reactors

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Bartel, N.; Chen, M.; Utgikar, V. P.; Sun, X.; Kim, I. H.; Christensen, R.; Sabharwall, P.

    2015-07-01T23:59:59.000Z

    A comparative evaluation of alternative compact heat exchanger designs for use as the intermediate heat exchanger in advanced nuclear reactor systems is presented in this article. Candidate heat exchangers investigated included the Printed circuit heat exchanger (PCHE) and offset strip-fin heat exchanger (OSFHE). Both these heat exchangers offer high surface area to volume ratio (a measure of compactness [m2/m3]), high thermal effectiveness, and overall low pressure drop. Helium–helium heat exchanger designs for different heat exchanger types were developed for a 600 MW thermal advanced nuclear reactor. The wavy channel PCHE with a 15° pitch angle was found to offer optimummore »combination of heat transfer coefficient, compactness and pressure drop as compared to other alternatives. The principles of the comparative analysis presented here will be useful for heat exchanger evaluations in other applications as well.« less

  9. Building America Expert Meeting: Key Innovations for Adding Energy...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Key Innovations for Adding Energy Efficiency to Maintenance Projects Building America Expert Meeting: Key Innovations for Adding Energy Efficiency to Maintenance Projects This...

  10. Energy Department to Launch New Energy Innovation Hub Focused...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    to Launch New Energy Innovation Hub Focused on Advanced Batteries and Energy Storage Energy Department to Launch New Energy Innovation Hub Focused on Advanced Batteries and Energy...

  11. Next Generation Advanced Framing - Building America Top Innovation...

    Broader source: Energy.gov (indexed) [DOE]

    about this Top Innovation. See an example of this Top Innovation in action. Find more case studies of Building America projects across the country that demonstrate advanced...

  12. Buried and Encapsulated Ducts - Building America Top Innovation...

    Energy Savers [EERE]

    about this Top Innovation. See an example of this Top Innovation in action. Find more case studies of Building America projects across the country that demonstrate buried and...

  13. Outside Air Ventilation Controller - Building America Top Innovation...

    Energy Savers [EERE]

    about this Top Innovation. See an example of this Top Innovation in action. Find more case studies of Building America projects across the country that are implementing outside...

  14. Energy Department Awards More Than $7 Million for Innovative...

    Office of Environmental Management (EM)

    More Than 7 Million for Innovative Hydrogen Storage Technologies in Fuel Cell Electric Vehicles Energy Department Awards More Than 7 Million for Innovative Hydrogen Storage...

  15. Sandia Energy - Innovative Offshore Vertical-Axis Wind Turbine...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Vertical-Axis Wind Turbine Rotors Home Stationary Power Energy Conversion Efficiency Wind Energy Offshore Wind Innovative Offshore Vertical-Axis Wind Turbine Rotors Innovative...

  16. Ten New Mexico small businesses recognized at Innovation Celebration...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NM small businesses recognized at Innovation Celebration Ten New Mexico small businesses recognized at Innovation Celebration April 3 Small businesses participating in projects...

  17. Collegiate Wind Competition Engages Tomorrow's Wind Energy Innovators...

    Office of Environmental Management (EM)

    Engages Tomorrow's Wind Energy Innovators Collegiate Wind Competition Engages Tomorrow's Wind Energy Innovators January 6, 2014 - 10:00am Addthis 2014 Collegiate Teams Boise State...

  18. Winning the Future: Chaninik Wind Group Pursues Innovative Solutions...

    Energy Savers [EERE]

    Winning the Future: Chaninik Wind Group Pursues Innovative Solutions to Native Alaska Energy Challenges Winning the Future: Chaninik Wind Group Pursues Innovative Solutions to...

  19. Virginia Tech Selected to Continue Development of Innovative...

    Office of Environmental Management (EM)

    Virginia Tech Selected to Continue Development of Innovative Building Automation System Virginia Tech Selected to Continue Development of Innovative Building Automation System...

  20. Energy Innovation Hub Report Shows Philadelphia-area Building...

    Office of Environmental Management (EM)

    Innovation Hub Report Shows Philadelphia-area Building Retrofits Could Support 23,500 Jobs Energy Innovation Hub Report Shows Philadelphia-area Building Retrofits Could Support...

  1. Removing Barriers to Innovations: Related Codes and Standards...

    Energy Savers [EERE]

    Removing Barriers to Innovations: Related Codes and Standards CSI Team Removing Barriers to Innovations: Related Codes and Standards CSI Team This presentation was delivered at the...

  2. Environmental Innovation Center Solar Site Evaluation: San José...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Information Resources Environmental Innovation Center Solar Site Evaluation: San Jos Environmental Innovation Center Solar Site Evaluation: San Jos This report describes the...

  3. Vehicle Technologies Office Announces $14 M in Funding for Innovative...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Announces 14 M in Funding for Innovative Technologies Vehicle Technologies Office Announces 14 M in Funding for Innovative Technologies January 16, 2015 - 4:26pm Addthis The...

  4. Addendum Added to Innovative Demonstration of Geothermal Energy...

    Office of Environmental Management (EM)

    Addendum Added to Innovative Demonstration of Geothermal Energy Production FOA Addendum Added to Innovative Demonstration of Geothermal Energy Production FOA July 2, 2010 - 2:13pm...

  5. Energy Department Announces Launch of Energy Innovation Hub for...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Launch of Energy Innovation Hub for Critical Materials Research Energy Department Announces Launch of Energy Innovation Hub for Critical Materials Research May 31, 2012 - 5:56pm...

  6. Building America Top Innovations Hall of Fame Profile - Building...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Building America Top Innovations Hall of Fame Profile - Building Energy Optimization Analysis Method (BEopt) Building America Top Innovations Hall of Fame Profile - Building Energy...

  7. EERE Leadership Discusses Energy Innovation in Midwest | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    EERE Leadership Discusses Energy Innovation in Midwest EERE Leadership Discusses Energy Innovation in Midwest October 28, 2014 - 3:06pm Addthis EERE Leadership Discusses Energy...

  8. Innovative Energy Efficiency, Renewable Energy, and Grid Technology...

    Energy Savers [EERE]

    Innovative Energy Efficiency, Renewable Energy, and Grid Technology Update Innovative Energy Efficiency, Renewable Energy, and Grid Technology Update April 29, 2015 11:00AM to...

  9. Energy Department Announces $18 Million for Innovative Projects...

    Energy Savers [EERE]

    Energy Department Announces 18 Million for Innovative Projects to Advance Geothermal Energy Energy Department Announces 18 Million for Innovative Projects to Advance Geothermal...

  10. Colorado Firm Develops Innovative Materials for Geothermal Systems...

    Office of Environmental Management (EM)

    Firm Develops Innovative Materials for Geothermal Systems Colorado Firm Develops Innovative Materials for Geothermal Systems April 18, 2013 - 12:00am Addthis With support from...

  11. The Geothermal Technologies Office Invests $18 Million for Innovative...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    The Geothermal Technologies Office Invests 18 Million for Innovative Projects The Geothermal Technologies Office Invests 18 Million for Innovative Projects The McGuiness Hills...

  12. AMO Requests Technical Topics Suitable for a Manufacturing Innovation...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Innovation Institute AMO Requests Technical Topics Suitable for a Manufacturing Innovation Institute April 17, 2014 - 12:23pm Addthis The Advanced Manufacturing Office...

  13. Small Business Innovation Research (SBIR) and Small Business...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Innovation Research (SBIR) and Small Business Technology Transfer (STTR) Small Business Innovation Research (SBIR) and Small Business Technology Transfer (STTR) An overview of the...

  14. ambitious innovation project: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    9 AMSUBC Innovative Projects Fund Policy. Revised February 2007. Stated Purpose Energy Storage, Conversion and Utilization Websites Summary: AMSUBC Innovative Projects Fund...

  15. Natural Innovative Renewable Energy formerly Northwest Iowa Renewable...

    Open Energy Info (EERE)

    Natural Innovative Renewable Energy formerly Northwest Iowa Renewable Energy Jump to: navigation, search Name: Natural Innovative Renewable Energy (formerly Northwest Iowa...

  16. Four of Popular Science's 100 best innovations from Los Alamos...

    National Nuclear Security Administration (NNSA)

    of Popular Science's 100 best innovations from Los Alamos, Sandia, Livermore Popular Science lists three of 100 best innovations from Los Alamos, Sandia Four of Popular Science's...

  17. Building Science-Based Climate Maps - Building America Top Innovation...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Science-Based Climate Maps - Building America Top Innovation Building Science-Based Climate Maps - Building America Top Innovation Photo showing climate zone maps based on the IECC...

  18. Virtual Oxygen Sensor for Innovative NOx and PM Emission Control...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Virtual Oxygen Sensor for Innovative NOx and PM Emission Control Technologies Virtual Oxygen Sensor for Innovative NOx and PM Emission Control Technologies A virtual O2 sensor for...

  19. Innovation and Coordination at the Callifornia Fuel Cell Partnership...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Innovation and Coordination at the Callifornia Fuel Cell Partnership Innovation and Coordination at the Callifornia Fuel Cell Partnership Presented at Refueling Infrastructure for...

  20. Innovative High-Performance Deposition Technology for Low-Cost...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Innovative High-Performance Deposition Technology for Low-Cost Manufacturing of OLED Lighting Innovative High-Performance Deposition Technology for Low-Cost Manufacturing of OLED...

  1. Cleantech SBIR: Small Business Innovation Research (SBIR) for...

    Energy Savers [EERE]

    Business Innovation Research (SBIR) for the Office of Energy Efficiency and Renewable Energy Cleantech SBIR: Small Business Innovation Research (SBIR) for the Office of Energy...

  2. Rare-earth innovation to improve nylon manufacturing | The Ames...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Rare-earth innovation to improve nylon manufacturing The Critical Materials Institute, a Department of Energy Innovation Hub led by the Ames Labratory, has created a new chemical...

  3. Alkaline Membrane Fuel Cell Workshop Welcome and OverviewInnovation

    Broader source: Energy.gov (indexed) [DOE]

    Alkaline Membrane Fuel Cell Workshop Welcome and Overview Innovation for Our Energy Future Bryan Pivovar National Renewable Energy Laboratory AMFC Workshop May 8, 2011 Innovation...

  4. Energy Department Announces New Investment in Innovative Small...

    Energy Savers [EERE]

    Energy Department Announces New Investment in Innovative Small Modular Reactor Energy Department Announces New Investment in Innovative Small Modular Reactor December 12, 2013 -...

  5. Water Management Guide - Building America Top Innovation | Department...

    Energy Savers [EERE]

    Water Management Guide - Building America Top Innovation Water Management Guide - Building America Top Innovation Cover of the EEBA Water Management Guide. As energy codes and...

  6. Fuel Station of the Future- Innovative Approach to Fuel Cell...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Station of the Future- Innovative Approach to Fuel Cell Technology Unveiled in California Fuel Station of the Future- Innovative Approach to Fuel Cell Technology Unveiled in...

  7. Sandia Energy - Innovative Offshore Vertical-Axis Wind Turbine...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Innovative Offshore Vertical-Axis Wind Turbine Rotors Home Stationary Power Energy Conversion Efficiency Wind Energy Offshore Wind Innovative Offshore Vertical-Axis Wind Turbine...

  8. Glosten Associates Tests Innovative High-Strength Mooring Lines...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Glosten Associates Tests Innovative High-Strength Mooring Lines for Deepwater Offshore Wind Installations Glosten Associates Tests Innovative High-Strength Mooring Lines for...

  9. DOE Issues Funding Opportunity for Innovations to Increase Cybersecuri...

    Office of Environmental Management (EM)

    Funding Opportunity for Innovations to Increase Cybersecurity for Energy Delivery Systems DOE Issues Funding Opportunity for Innovations to Increase Cybersecurity for Energy...

  10. A Systems Biology Approach to Infectious Disease Research: Innovating...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Systems Biology Approach to Infectious Disease Research: Innovating the Pathogen-Host Research Paradigm. A Systems Biology Approach to Infectious Disease Research: Innovating the...

  11. Developing Biomimetic Design Principles for the Highly Optimized and Robust Design of Products and Their Components 

    E-Print Network [OSTI]

    Wadia, Anosh Porus

    2011-10-21T23:59:59.000Z

    Engineering design methods focus on developing products that are innovative, robust, and multi-functional. In this context, the term robust refers to a product's ability to accomplish successfully its predetermined functions. ...

  12. Plasma-enhanced gasification of low-grade coals for compact power plants

    SciTech Connect (OSTI)

    Uhm, Han S. [Department of Electrophysics, Kwangwoon University, 447-1 Wolgye-Dong, Nowon-Gu, Seoul 139-701 (Korea, Republic of); Hong, Yong C.; Shin, Dong H.; Lee, Bong J. [Convergence Plasma Research Center, National Fusion Research Institute, 113 Gwahangno, Yuseong-Gu, Daejeon 305-333 (Korea, Republic of)

    2011-10-15T23:59:59.000Z

    A high temperature of a steam torch ensures an efficient gasification of low-grade coals, which is comparable to that of high-grade coals. Therefore, the coal gasification system energized by microwaves can serve as a moderately sized power plant due to its compact and lightweight design. This plasma power plant of low-grade coals would be useful in rural or sparsely populated areas without access to a national power grid.

  13. An analysis of selected factors controlling or affecting the hydraulic conductivity of compacted soil liners

    E-Print Network [OSTI]

    Speake, Robert Cary

    1986-01-01T23:59:59.000Z

    , and maintenance of compacted so11 liners for use 1n waste management facilities. CHAPTER II U. S. ENVIRONMENTAL PROTECTION AGENCY DESIGN REI}UIREMENTS FOR CERTAIN WASTE NANAGENENT FACILITIES On November 8, 1984, the President signed into law the Hazardous... and Solid Waste Amendments of 1984 (HSWA) to the Resource Conservation and Recovery Act of 1976 (RCRA). Under Sections 3004(o) and 3015 of HSWA, certain landfills and surface impoundments are required to have "two or more liners and a leachate collection...

  14. Innovative Design Concept for the New Bangkok International Airport, NBIA 

    E-Print Network [OSTI]

    Kessling, W.; Holst, S.; Schuler, M.

    2004-01-01T23:59:59.000Z

    Thermal and visual comfort for the occupants of a room are not defined by air temperature only, but also radiation with its three components solar radiation, daylight and heat radiation has to be taken into account (among other factors...

  15. Innovative Cooling Design Traditional data centers circulate mechanically

    E-Print Network [OSTI]

    center. High Performance Computing Data Center The new high performance computing (HPC) data center performance computing. The ESIF HPC data center is approximately 10,000 sf2 of uninterrupted, usable machine demonstrating best-in-class technologies for a holistic, integrated approach to energy efficient high

  16. An innovative concept for deep water oil production platform design

    E-Print Network [OSTI]

    Racine, Florian

    1994-01-01T23:59:59.000Z

    and Off loading Tower) is studied in this thesis. Instead of using a single large cylindrical structure as in the spar configuration, the FPSOT utilizes a jacket-type framed structure supported by a buoyancy/storage tank deep below the ocean surface...

  17. The Kinetostatic Design of an Innovative Schonflies Motion Generator

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    and State of the Art Most industrial robots have articulated structures of the serial type, where each link

  18. Thermomechanical analysis of innovative nuclear fuel pin designs

    E-Print Network [OSTI]

    Lerch Andrew (Andrew J.)

    2010-01-01T23:59:59.000Z

    One way to increase the power of a nuclear reactor is to change the solid cylindrical fuel to Internally and Externally Cooled (I&EC) annular fuel, and adjust the flow and the core inlet coolant temperature. The switch to ...

  19. Innovative Design Concept for the New Bangkok International Airport, NBIA

    E-Print Network [OSTI]

    Kessling, W.; Holst, S.; Schuler, M.

    2004-01-01T23:59:59.000Z

    the zenith. The situation of an international airport with 24- hours working days and high internal heat loads from people, electric equipment and lighting combined with the desired indoor climate conditions of 24 ?C room temperature and 50 to 60 % relative... the existing hourly weather data for Bangkok a period with extremely high daily top temperatures of 34 ?C and a horizontal solar radiation of 1,000 W/m? was chosen as the basis for comparing several concept variants. The model has four thermal zones: First...

  20. Innovative High Energy Density Capacitor Design Offers Potential...

    Broader source: Energy.gov (indexed) [DOE]

    provided 75,000 as part of an initial cooperative research and development agreement (CRADA) that allowed TroyCap to engage with LLNL. By the end of the CRADA, TroyCap had...