Sample records for industrial sector asphalt

  1. Asphalt roofing industry Fourier transform infrared spectroscopy modified bitumen

    SciTech Connect (OSTI)

    NONE

    1999-07-01T23:59:59.000Z

    A Request for Emissions Testing at Four Asphalt Roofing and Processing Facilities was submitted by the US EPA Emission Standards Division (ESD), Minerals and Inorganic Chemicals Group (MICG) to the Emission Measurement Center (EMC). The Emission Measurement Center directed Midwest Research Institute (MRI) to conduct emissions testing at asphalt roofing plants. This report presents results of MRI`s FTIR and Method 25A testing conducted at US Intec in Port Arthur, Texas. The field measurements were performed in September 1997 under several test conditions for both controlled and uncontrolled emissions.

  2. Designing Effective State Programs for the Industrial Sector...

    Energy Savers [EERE]

    Sector - New SEE Action Publication March 24, 2014 - 12:56pm Addthis Industrial Energy Efficiency: Designing Effective State Programs for the Industrial Sector provides...

  3. Strategies for Low Carbon Growth In India: Industry and Non Residential Sectors

    E-Print Network [OSTI]

    Sathaye, Jayant

    2011-01-01T23:59:59.000Z

    Efficiency Scenario (non-residential sector only) – AssumesIndia: Industry and Non Residential Sectors Jayant Sathaye,and support. The Non Residential sector analysis benefited

  4. Aged asphalt

    E-Print Network [OSTI]

    Martin, Kenneth Lloyd

    1988-01-01T23:59:59.000Z

    Dorchester Asphalts Exxon Asphalts CONCLUSIONS RECOMMENDATIONS LITERATURE CITED APPENDIX 41 42 48 59 70 84 90 93 96 99 103 105 106 A. GEL PERMEATION CHROMATOGRAMS OF TEST ASPHALTS 108 B. FOURIER-TRANSFORM INFRARED SPECTRUMS OF TEST... Apparatus 5. Abson Method Apparatus 6. ASTM D 2171 Apparatus 7. Sample Pellet Die 8. Sample Pellet Holder 21 23 27 29 38 40 9. GPC of Lufkin Exxon AC-20 Extracted by Two Methods . . . . . . . . . . . . . . . . 46 10. GPC of Dickens Exxon AC-20 51...

  5. Cross-Sector Impact Analysis of Industrial Efficiency Measures

    SciTech Connect (OSTI)

    Morrow, William [Lawrence Berkeley National Laboratory (LBNL)] [Lawrence Berkeley National Laboratory (LBNL); CreskoEngineering, Joe [Oak Ridge Institute for Science and Education (ORISE); Carpenter, Alberta [National Renewable Energy Laboratory (NREL)] [National Renewable Energy Laboratory (NREL); Masanet, Eric [Northwestern University, Evanston] [Northwestern University, Evanston; Nimbalkar, Sachin U [ORNL] [ORNL; Shehabi, Arman [Lawrence Berkeley National Laboratory (LBNL)] [Lawrence Berkeley National Laboratory (LBNL)

    2013-01-01T23:59:59.000Z

    The industrial or manufacturing sector is a foundational component to all economic activity. In addition to being a large direct consumer of energy, the manufacturing sector also produces materials, products, and technologies that influence the energy use of other economic sectors. For example, the manufacturing of a lighter-weight vehicle component affects the energy required to ship that component as well as the fuel efficiency of the assembled vehicle. Many energy efficiency opportunities exist to improve manufacturing energy consumption, however comparisons of manufacturing sector energy efficiency investment opportunities tend to exclude any impacts that occur once the product leaves the factory. Expanding the scope of analysis to include energy impacts across different stages of product life-cycle can highlight less obvious opportunities and inform actions that create the greatest economy-wide benefits. We present a methodology and associated analysis tool (LIGHTEnUP Lifecycle Industry GHgas, Technology and Energy through the Use Phase) that aims to capture both the manufacturing sector energy consumption and product life-cycle energy consumption implications of manufacturing innovation measures. The tool architecture incorporates U.S. national energy use data associated with manufacturing, building operations, and transportation. Inputs for technology assessment, both direct energy saving to the manufacturing sector, and indirect energy impacts to additional sectors are estimated through extensive literature review and engineering methods. The result is a transparent and uniform system of comparing manufacturing and use-phase impacts of technologies.

  6. Energy Use and Savings in the Canadian Industrial Sector

    E-Print Network [OSTI]

    James, B.

    1982-01-01T23:59:59.000Z

    The changing role of energy as a production input in the industrial sector in Canada is examined. Energy use patterns are reviewed in terms of the energy input types, both purchased and self-produced, the actual energy form and quality requirements...

  7. Energy Use and Savings in the Canadian Industrial Sector 

    E-Print Network [OSTI]

    James, B.

    1982-01-01T23:59:59.000Z

    The changing role of energy as a production input in the industrial sector in Canada is examined. Energy use patterns are reviewed in terms of the energy input types, both purchased and self-produced, the actual energy form and quality requirements...

  8. Analysis of fuel shares in the industrial sector

    SciTech Connect (OSTI)

    Roop, J.M.; Belzer, D.B.

    1986-06-01T23:59:59.000Z

    These studies describe how fuel shares have changed over time; determine what factors are important in promoting fuel share changes; and project fuel shares to the year 1995 in the industrial sector. A general characterization of changes in fuel shares of four fuel types - coal, natural gas, oil and electricity - for the industrial sector is as follows. Coal as a major fuel source declined rapidly from 1958 to the early 1970s, with oil and natural gas substituting for coal. Coal's share of total fuels stabilized after the oil price shock of 1972-1973, and increased after the 1979 price shock. In the period since 1973, most industries and the industrial sector as a whole appear to freely substitute natural gas for oil, and vice versa. Throughout the period 1958-1981, the share of electricity as a fuel increased. These observations are derived from analyzing the fuel share patterns of more than 20 industries over the 24-year period 1958 to 1981.

  9. TECHNICAL POLLUTION PREVENTION GUIDE FOR ASPHALT PREPARATION OPERATIONS

    E-Print Network [OSTI]

    Delivery, Storage and Cold Feed . . . . . . . . . . . . . 12 2.3.2 Liquid Asphalt Delivery, Storage . . . . . . . . . . . . . . . . . . . . . . 4 2 INDUSTRY PROFILE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1 ASPHALT and Heating . . . . . . . . . . . . 12 2.3.3 Cold Feed Drying and Heating

  10. Perform, Achieve and Trade (PAT): An Innovative Mechanism for Enhancing Energy Efficiency in India's Industrial Sector

    E-Print Network [OSTI]

    Garnik, S. P.; Martin, M.

    2014-01-01T23:59:59.000Z

    On 31st March 2012, India quietly announced a historic regulation for industrial sector in a bid to ensure energy security of the country. The regulation, with an aim to enhance energy efficiency in energy intensive industrial sectors, is empowered...

  11. Efficient Energy Utilization in the Industrial Sector - Case Studies 

    E-Print Network [OSTI]

    Davis, S. R.

    1984-01-01T23:59:59.000Z

    . As indicated earlier, the industrial complex, w~ich uses 44 percent of the total energy, has the langest share in the balancing of energy supply and dem~nd. Because of this, many companies are finding that an organized energy conservation program can reduc... is now expen sive; therefore, the available supply of cheap oil and gas is being rapidly exhausted, and consumption cannot continue to grow at the pace to which we have become accustomed. Changes are taking place, espe cially in the industrial sector...

  12. Energy use and CO2 emissions of China’s industrial sector from a global perspective

    SciTech Connect (OSTI)

    Zhou, Sheng; Kyle, G. Page; Yu, Sha; Clarke, Leon E.; Eom, Jiyong; Luckow, Patrick W.; Chaturvedi, Vaibhav; Zhang, Xiliang; Edmonds, James A.

    2013-07-10T23:59:59.000Z

    The industrial sector has accounted for more than 50% of China’s final energy consumption in the past 30 years. Understanding the future emissions and emissions mitigation opportunities depends on proper characterization of the present-day industrial energy use, as well as industrial demand drivers and technological opportunities in the future. Traditionally, however, integrated assessment research has handled the industrial sector of China in a highly aggregate form. In this study, we develop a technologically detailed, service-oriented representation of 11 industrial subsectors in China, and analyze a suite of scenarios of future industrial demand growth. We find that, due to anticipated saturation of China’s per-capita demands of basic industrial goods, industrial energy demand and CO2 emissions approach a plateau between 2030 and 2040, then decrease gradually. Still, without emissions mitigation policies, the industrial sector remains heavily reliant on coal, and therefore emissions-intensive. With carbon prices, we observe some degree of industrial sector electrification, deployment of CCS at large industrial point sources of CO2 emissions at low carbon prices, an increase in the share of CHP systems at industrial facilities. These technological responses amount to reductions of industrial emissions (including indirect emission from electricity) are of 24% in 2050 and 66% in 2095.

  13. Analysis of Energy Use in Building Services of the Industrial Sector in California: A Literature Review and a Preliminary Characterization

    E-Print Network [OSTI]

    Akbari, H.

    2008-01-01T23:59:59.000Z

    Sector Market Study Report to Pacific Gas and Electric (Gas and Electric Company (PG&E) industrial audits [9], Industrial Sector Market Study of PG&E customers, (a report

  14. World Best Practice Energy Intensity Values for Selected Industrial Sectors

    E-Print Network [OSTI]

    Worrell, Ernst; Price, Lynn; Neelis, Maarten; Galitsky, Christina; Zhou, Nan

    2007-01-01T23:59:59.000Z

    energy efficiency in the petrochemical industry,” Chapter 3steel, petroleum and petrochemical, chemical, non-ferrousintensive process in the petrochemical industry with an

  15. Climate VISION: PrivateSector Initiatives: Minerals - Industry...

    Office of Scientific and Technical Information (OSTI)

    Industry Associations Industrial Minerals Association - North America The International Minerals Association - North America (IMA-NA) was formed in early 2002 to tap the benefits...

  16. Public Interest Energy Research (PIER) Program FINAL PROJECT REPORT California Energy Balance Update and Decomposition Analysis for the Industry and Building Sectors

    E-Print Network [OSTI]

    de la Rue du Can, Stephane

    2014-01-01T23:59:59.000Z

    Energy Balance Update and Decomposition Analysis for the Industry and Building SectorsEnergy Balance Update and Decomposition Analysis for the Industry and Building SectorsEnergy Balance Update and Decomposition Analysis for the Industry and Building Sectors.

  17. Study of properties of sand asphalt using a torsional rheometer 

    E-Print Network [OSTI]

    Kasula, Lavan Kumar Reddy

    2004-11-15T23:59:59.000Z

    The modeling of Sand Asphalt and experiments to measure their rheological properties are of vital concern to many industrial processes especially highway and roadway pavement construction industry. A variety of hot mix ...

  18. Industrial Sector Energy Demand: Revisions for Non-Energy-Intensive Manufacturing (released in AEO2007)

    Reports and Publications (EIA)

    2007-01-01T23:59:59.000Z

    For the industrial sector, the Energy Information Administration's (EIA) analysis and projection efforts generally have focused on the energy-intensive industriesfood, bulk chemicals, refining, glass, cement, steel, and aluminumwhere energy cost averages 4.8% of annual operating cost. Detailed process flows and energy intensity indicators have been developed for narrowly defined industry groups in the energy-intensive manufacturing sector. The non-energy-intensive manufacturing industries, where energy cost averages 1.9% of annual operating cost, previously have received somewhat less attention, however. In Annual Energy Outlook 2006 (AEO), energy demand projections were provided for two broadly aggregated industry groups in the non-energy-intensive manufacturing sector: metal-based durables and other non-energy-intensive. In the AEO2006 projections, the two groups accounted for more than 50% of the projected increase in industrial natural gas consumption from 2004 to 2030.

  19. Strategies for Low Carbon Growth In India: Industry and Non Residential Sectors

    SciTech Connect (OSTI)

    Sathaye, Jayant; de la Rue du Can, Stephane; Iyer, Maithili; McNeil, Michael; Kramer, Klaas Jan; Roy, Joyashree; Roy, Moumita; Chowdhury, Shreya Roy

    2011-04-15T23:59:59.000Z

    This report analyzed the potential for increasing energy efficiency and reducing greenhouse gas emissions (GHGs) in the non-residential building and the industrial sectors in India. The first two sections describe the research and analysis supporting the establishment of baseline energy consumption using a bottom up approach for the non residential sector and for the industry sector respectively. The third section covers the explanation of a modeling framework where GHG emissions are projected according to a baseline scenario and alternative scenarios that account for the implementation of cleaner technology.

  20. BC Hydro Industrial Sector: Marketing Sector Marketing Plan (Fiscal 2005/Fiscal 2006)

    E-Print Network [OSTI]

    Willis, P.; Wallace, K.

    2005-01-01T23:59:59.000Z

    BC Hydro, the major electricity utility in the Province of British Columbia has been promoting industrial energy efficiency for more than 15 years. Recently it has launched a new Demand Side Management initiative with the objective of obtaining 2000...

  1. Types of Nuclear Industry Jobs Commercial and Government Sectors

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of ScienceandMesa del SolStrengthening aTurbulence may be key to "fastTwistTypes of Nuclear Industry

  2. Greenhouse Gas Emission Reduction in the ENERGY STAR Commercial, Industrial and Residential Sectors. An Example of How the Refinery Industry is Capitalizing on ENERGY STAR

    E-Print Network [OSTI]

    Patrick, K.

    2008-01-01T23:59:59.000Z

    Greenhouse Gas Emission Reduction in the ENERGY STAR Commercial, Industrial and Residential Sectors. An Example of how the Refinery Industry is Capitalizing on ENERGY STAR Kelly Patrick U.S. Environmental Protection Agency kelly...

  3. Comparative analysis of energy data bases for the industrial and commercial sectors

    SciTech Connect (OSTI)

    Roop, J.M.; Belzer, D.B.; Bohn, A.A.

    1986-12-01T23:59:59.000Z

    Energy data bases for the industrial and commercial sectors were analyzed to determine how valuable this data might be for policy analysis. The approach is the same for both end-use sectors: first a descrption or overview of relevant data bases identifies the available data; the coverage and methods used to generate the data are then explained; the data are then characterized and examples are provided for the major data sets under consideration. A final step assesses the data bases under consideration and draws conclusions. There are a variety of data bases considered for each of the end-use sectors included in this report. Data bases for the industrial sector include the National Energy Accounts, process-derived data bases such as the Drexel data base and data obtained from industry trade associations. For the commercial sector, three types of data bases are analyzed: the Nonresidential Building Energy Consumption Surveys, Dodge Construction Data and the Building Owners and Manager's Association Experience Exchange Report.

  4. he agricultural sector is rapidly being trans-formed into an industry of major importance

    E-Print Network [OSTI]

    Antsaklis, Panos

    T he agricultural sector is rapidly being trans- formed into an industry of major importance, with superior performance in most cases. To manage the increasing complexity of agricultural systems agri- culture, where the goal is to improve the efficiency of opera- tion of agricultural enterprises

  5. Asphalt Oxidation Kinetics and Pavement Oxidation Modeling

    E-Print Network [OSTI]

    Jin, Xin

    2012-07-16T23:59:59.000Z

    Most paved roads in the United States are surfaced with asphalt. These asphalt pavements suffer from fatigue cracking and thermal cracking, aggravated by the oxidation and hardening of asphalt. This negative impact of asphalt oxidation on pavement...

  6. Model documentation report: Industrial sector demand module of the National Energy Modeling System

    SciTech Connect (OSTI)

    NONE

    1997-01-01T23:59:59.000Z

    This report documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Industrial Demand Model. The report catalogues and describes model assumptions, computational methodology, parameter estimation techniques, and model source code. This document serves three purposes. First, it is a reference document providing a detailed description of the NEMS Industrial Model for model analysts, users, and the public. Second, this report meets the legal requirement of the Energy Information Administration (EIA) to provide adequate documentation in support of its models. Third, it facilitates continuity in model development by providing documentation from which energy analysts can undertake model enhancements, data updates, and parameter refinements as future projects. The NEMS Industrial Demand Model is a dynamic accounting model, bringing together the disparate industries and uses of energy in those industries, and putting them together in an understandable and cohesive framework. The Industrial Model generates mid-term (up to the year 2015) forecasts of industrial sector energy demand as a component of the NEMS integrated forecasting system. From the NEMS system, the Industrial Model receives fuel prices, employment data, and the value of industrial output. Based on the values of these variables, the Industrial Model passes back to the NEMS system estimates of consumption by fuel types.

  7. Economies of Scale and Scope in Network Industries: Lessons for the UK water and sewerage sectors

    E-Print Network [OSTI]

    Pollitt, Michael G.; Steer, Stephen J.

    means that water markets globally (and specifically the demand for water and sewerage services) will continue to grow well into the twenty-first century. Since 1960 the world population has doubled to approximately 7 billion today, and is projected... sectors1 Michael G. Pollitt Steven J. Steer ESRC Electricity Policy Research Group University of Cambridge August 2011 Abstract Many studies of the water and sewerage industries place significant importance on the benefits of economies...

  8. Sector trends and driving forces of global energy use and greenhouse gas emissions: focus in industry and buildings

    SciTech Connect (OSTI)

    Price, Lynn; Worrell, Ernst; Khrushch, Marta

    1999-09-01T23:59:59.000Z

    Disaggregation of sectoral energy use and greenhouse gas emissions trends reveals striking differences between sectors and regions of the world. Understanding key driving forces in the energy end-use sectors provides insights for development of projections of future greenhouse gas emissions. This report examines global and regional historical trends in energy use and carbon emissions in the industrial, buildings, transport, and agriculture sectors, with a more detailed focus on industry and buildings. Activity and economic drivers as well as trends in energy and carbon intensity are evaluated. The authors show that macro-economic indicators, such as GDP, are insufficient for comprehending trends and driving forces at the sectoral level. These indicators need to be supplemented with sector-specific information for a more complete understanding of future energy use and greenhouse gas emissions.

  9. Evaluation of Efficiency Activities in the Industrial Sector Undertaken in Response to Greenhouse Gas Emission Reduction Targets

    E-Print Network [OSTI]

    Price, Lynn

    2010-01-01T23:59:59.000Z

    20april%202006.pdf ETSU, 1999. Industrial Sector CarbonSee discussion of this report in ETSU, AEA Technology, 2001.a report prepared by ETSU (now AEA Energy & Environment) on

  10. Published by Oak Ridge National Laboratory No. 1 2010 The industrial sector accounts for nearly one-third of the

    E-Print Network [OSTI]

    Pennycook, Steve

    Published by Oak Ridge National Laboratory No. 1 2010 The industrial sector accounts for nearly one research and development agreements (CRADAs) and two large work-for-others projects. Ev- ery single one

  11. Comparison Study of Energy Intensity in the Textile Industry: A Case Study in Five Textile Sub-sectors

    E-Print Network [OSTI]

    Hasanbeigi, A.; Hasanabadi, A.; Abdorrazaghi, M.

    2011-01-01T23:59:59.000Z

    This paper contributes to the understanding of energy use in the textile industry by comparing the energy intensity of textile plants in five major sub-sectors, i.e. spinning, weaving, wet-processing, worsted fabric manufacturing, and carpet...

  12. Long-term Industrial Energy Forecasting (LIEF) model (18-sector version)

    SciTech Connect (OSTI)

    Ross, M.H. [Univ. of Michigan, Ann Arbor, MI (US). Dept. of Physics; Thimmapuram, P.; Fisher, R.E.; Maciorowski, W. [Argonne National Lab., IL (US)

    1993-05-01T23:59:59.000Z

    The new 18-sector Long-term Industrial Energy Forecasting (LIEF) model is designed for convenient study of future industrial energy consumption, taking into account the composition of production, energy prices, and certain kinds of policy initiatives. Electricity and aggregate fossil fuels are modeled. Changes in energy intensity in each sector are driven by autonomous technological improvement (price-independent trend), the opportunity for energy-price-sensitive improvements, energy price expectations, and investment behavior. Although this decision-making framework involves more variables than the simplest econometric models, it enables direct comparison of an econometric approach with conservation supply curves from detailed engineering analysis. It also permits explicit consideration of a variety of policy approaches other than price manipulation. The model is tested in terms of historical data for nine manufacturing sectors, and parameters are determined for forecasting purposes. Relatively uniform and satisfactory parameters are obtained from this analysis. In this report, LIEF is also applied to create base-case and demand-side management scenarios to briefly illustrate modeling procedures and outputs.

  13. ISTUM PC: industrial sector technology use model for the IBM-PC

    SciTech Connect (OSTI)

    Roop, J.M.; Kaplan, D.T.

    1984-09-01T23:59:59.000Z

    A project to improve and enhance the Industrial Sector Technology Use Model (ISTUM) was originated in the summer of 1983. The project had dix identifiable objectives: update the data base; improve run-time efficiency; revise the reference base case; conduct case studies; provide technical and promotional seminars; and organize a service bureau. This interim report describes which of these objectives have been met and which tasks remain to be completed. The most dramatic achievement has been in the area of run-time efficiency. From a model that required a large proportion of the total resources of a mainframe computer and a great deal of effort to operate, the current version of the model (ISTUM-PC) runs on an IBM Personal Computer. The reorganization required for the model to run on a PC has additional advantages: the modular programs are somewhat easier to understand and the data base is more accessible and easier to use. A simple description of the logic of the model is given in this report. To generate the necessary funds for completion of the model, a multiclient project is proposed. This project will extend the industry coverage to all the industrial sectors, including the construction of process flow models for chemicals and petroleum refining. The project will also calibrate this model to historical data and construct a base case and alternative scenarios. The model will be delivered to clients and training provided. 2 references, 4 figures, 3 tables.

  14. Evaluation of Efficiency Activities in the Industrial Sector Undertaken in Response to Greenhouse Gas Emission Reduction Targets

    SciTech Connect (OSTI)

    Price, Lynn; de la Rue du Can, Stephane; Lu, Hongyou; Horvath, Arpad

    2010-05-21T23:59:59.000Z

    The 2006 California Global Warming Solutions Act calls for reducing greenhouse gas (GHG) emissions to 1990 levels by 2020. Meeting this target will require action from all sectors of the California economy, including industry. The industrial sector consumes 25% of the energy used and emits 28% of the carbon dioxide (CO{sub 2}) produced in the state. Many countries around the world have national-level GHG reduction or energy-efficiency targets, and comprehensive programs focused on implementation of energy efficiency and GHG emissions mitigation measures in the industrial sector are essential for achieving their goals. A combination of targets and industry-focused supporting programs has led to significant investments in energy efficiency as well as reductions in GHG emissions within the industrial sectors in these countries. This project has identified program and policies that have effectively targeted the industrial sector in other countries to achieve real energy and CO{sub 2} savings. Programs in Ireland, France, The Netherlands, Denmark, and the UK were chosen for detailed review. Based on the international experience documented in this report, it is recommended that companies in California's industrial sector be engaged in a program to provide them with support to meet the requirements of AB32, The Global Warming Solution Act. As shown in this review, structured programs that engage industry, require members to evaluate their potential efficiency measures, plan how to meet efficiency or emissions reduction goals, and provide support in achieving the goals, can be quite effective at assisting companies to achieve energy efficiency levels beyond those that can be expected to be achieved autonomously.

  15. asphalt: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    asphalt pavements containing asphalt binder and aggregates. The use of RAP can reduce the cost of construction materials, reduce the amount of waste... Thakur, Jitendra Kumar...

  16. asphalts: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    asphalt pavements containing asphalt binder and aggregates. The use of RAP can reduce the cost of construction materials, reduce the amount of waste... Thakur, Jitendra Kumar...

  17. Recycling asphaltic concrete with sulphur as a supplemental binder

    E-Print Network [OSTI]

    Barnett, Robert William

    1976-01-01T23:59:59.000Z

    in the United States, and the use of this secondary sulphur for construction purposes could provide not only a vast savings of natural resources and reusable materials but also aid industry in recovering the cost of environ- mental protection. The waste... industry [25, 26, 27, 28]. Research has been undertaken to investigate the use of sulphur in sand-asphalt- sulphur pavement mixes [11, 25, 29, 30]. The use of sulphur in sulphur-asphalt emulsions to serve as a binder has also been studied [26, 31, 32...

  18. World Best Practice Energy Intensity Values for SelectedIndustrial Sectors

    SciTech Connect (OSTI)

    Worrell, Ernst; Price, Lynn; Neelis, Maarten; Galitsky,Christina; Zhou, Nan

    2007-06-05T23:59:59.000Z

    "World best practice" energy intensity values, representingthe most energy-efficient processes that are in commercial use in atleast one location worldwide, are provided for the production of iron andsteel, aluminium, cement, pulp and paper, ammonia, and ethylene. Energyintensity is expressed in energy use per physical unit of output for eachof these commodities; most commonly these are expressed in metric tonnes(t). The energy intensity values are provided by major energy-consumingprocesses for each industrial sector to allow comparisons at the processlevel. Energy values are provided for final energy, defined as the energyused at the production facility as well as for primary energy, defined asthe energy used at the production facility as well as the energy used toproduce the electricity consumed at the facility. The "best practice"figures for energy consumption provided in this report should beconsidered as indicative, as these may depend strongly on the materialinputs.

  19. BBR Asphalt mixture creep test BBR Asphalt mixture creep size effect

    E-Print Network [OSTI]

    Minnesota, University of

    #12;Outline ØBBR Asphalt mixture creep test ØBBR Asphalt mixture creep size effect ØBBR Asphalt Point Bending Test Low temperature 3-point bending creep tests on specimens with three different sizes mixture strength test ØBBR Asphalt binder strength test #12;Asphalt Pavements ØRecent efforts under NCHRP

  20. Strategies for Low Carbon Growth In India: Industry and Non Residential Sectors

    E-Print Network [OSTI]

    Sathaye, Jayant

    2011-01-01T23:59:59.000Z

    public sector, and one in the private sector. Total energy consumptionenergy consumption increased by over 60% in the commercial building (including both public and private) sector.public sector ownership. 2.2.3 Energy data At the national or state level, end-use level energy consumption

  1. Effect of pyrolyzed carbon black on asphalt cement. Part 2. Asphalt binder. Final report, September 1993-May 1995

    SciTech Connect (OSTI)

    Zeng, Y.; Lovell, C.W.

    1996-02-20T23:59:59.000Z

    Scrap tires derived from automobiles have become a large environmental problem in the United States. In the study, research is carried out to investigate the potential use of tire-derived pyrolyzed carbon black from scrap tires as an asphalt cement modifier. The asphlat cements used in the research were AC10 and AC20. Penetration and softening point tests were performed to obtain the consistency of the asphalt cements. The pyrolyzed carbon black, as provided by Wolf Industries, was combined with the asphalt cement in the following percentages: 5%, 10%, 15% and 20%. Penetration, softening point and ductility tests were performed to determine the temperature susceptibility of the modified binder as altered by the pyrolyzed carbon black. In order that the results are comparable to previous testing, commercial carbon black purchased from CABOT Industry was also used as a modifier in the tests. The same test procedures were applied to the asphalt cements modified by commercial carbon black. The test results contained in the report illustrate the viability of the pyrolyzed carbon black as an asphalt modifier. Recommendations are provided to facilitate further research on this particular project. A preliminary assessment of a test road using the pyrolyzed carbon is appended.

  2. Stormwater Best Management Practices (BMPs) for Selected Industrial Sectors in the Lower Fraser Basin

    E-Print Network [OSTI]

    Concrete Industry Lime Industry Refined Petroleum Products (Bulk Storage) Other Petroleum and Coal Products and Planing Mill Products Industry Wire and Wire Products Industries Hydraulic Cernent Industry Ready Mixed

  3. Asphalt Pavement Aging and Temperature Dependent Properties through a Functionally

    E-Print Network [OSTI]

    Paulino, Glaucio H.

    Asphalt Pavement Aging and Temperature Dependent Properties through a Functionally Graded ­ II ­ Asphalt Pavements ­ Effect of Aging ­ Simulations ­ Concluding Remarks #12;3 Objectives Develop) Correspondence Principle based formulation Application: Asphalt concrete pavements (Part II) #12;4 Asphalt

  4. Nuclear Energy R&D Imperative 3: Enable a Transition Away from Fossil Fuel in the Transportation and Industrial Sectors

    SciTech Connect (OSTI)

    David Petti; J. Stephen Herring

    2010-03-01T23:59:59.000Z

    As described in the Department of Energy Office of Nuclear Energy’s Nuclear Energy R&D Roadmap, nuclear energy can play a significant role in supplying energy for a growing economy while reducing both our dependence on foreign energy supplies and emissions from the burning of fossil fuels. The industrial and transportation sectors are responsible for more than half of the greenhouse gas emissions in the U.S., and imported oil supplies 70% of the energy used in the transportation sector. It is therefore important to examine the various ways nuclear energy can facilitate a transition away from fossil fuels to secure environmentally sustainable production and use of energy in the transportation and manufacturing industry sectors. Imperative 3 of the Nuclear Energy R&D Roadmap, entitled “Enable a Transition Away from Fossil Fuels by Producing Process Heat for use in the Transportation and Industrial Sectors”, addresses this need. This document presents an Implementation Plan for R&D efforts related to this imperative. The expanded use of nuclear energy beyond the electrical grid will contribute significantly to overcoming the three inter-linked energy challenges facing U.S. industry: the rising and volatile prices for premium fossil fuels such as oil and natural gas, dependence on foreign sources for these fuels, and the risks of climate change resulting from carbon emissions. Nuclear energy could be used in the industrial and transportation sectors to: • Generate high temperature process heat and electricity to serve industrial needs including the production of chemical feedstocks for use in manufacturing premium fuels and fertilizer products, • Produce hydrogen for industrial processes and transportation fuels, and • Provide clean water for human consumption by desalination and promote wastewater treatment using low-grade nuclear heat as a useful additional benefit. Opening new avenues for nuclear energy will significantly enhance our nation’s energy security through more effective utilization of our country’s resources while simultaneously providing economic stability and growth (through predictable energy prices and high value jobs), in an environmentally sustainable and secure manner (through lower land and water use, and decreased byproduct emissions). The reduction in imported oil will also increase the retention of wealth within the U.S. economy while still supporting economic growth. Nuclear energy is the only non-fossil fuel that has been demonstrated to reliably supply energy for a growing industrial economy.

  5. How managing more efficiently substances in the design process of industrial products? An example from the aeronautics sector

    E-Print Network [OSTI]

    Lemagnen, Maud; Brissaud, Daniel

    2009-01-01T23:59:59.000Z

    Lowering environmental impacts of products, i.e. ecodesign, is considered today as a new and promising approach environment protection. This article focuses on ecodesign in the aeronautical sector through the analysis of the practices of a company that designs and produces engine equipments. Noise, gas emissions, fuel consumptions are the main environmental aspects which are targeted by aeronautics. From now on, chemical risk linked to the use of materials and production processes has to be traced, not only because of regulation pressure (e.g. REACh) but also because of customers requirements. So far, the aeronautical sector hasn't been focusing much on managing chemical risks at the design stage. However, new substances regulations notably require that chemical risk management should be by industries used as early as possible in their product development process. The aeronautics sector has therefore to elaborate new chemical risk management. The aim of this paper is to present a new method hat should be adap...

  6. Strategies for Low Carbon Growth In India: Industry and Non Residential Sectors

    E-Print Network [OSTI]

    Sathaye, Jayant

    2011-01-01T23:59:59.000Z

    from electricity generation, direct fuel combustion tofuel consumption in the commercial sector is assumed to be used entirely for back-up electricity generation.

  7. An investigation of three problems concerning the analysis of airborne asphalt fumes

    E-Print Network [OSTI]

    Laird, Larry Teal

    1981-01-01T23:59:59.000Z

    AN INVESTIGATION OF THREE PROBLEMS CONCERNING THE ANALYSIS OF AIRBORNE ASPHALT FUMES A Thesis by LARRY TEAL LAIRD Submitted to the Graduate College of Texas ASM University in partial fulfillment of the requirement for the degree of MASTER... OF SCIENCE May 1981 Major Subject: Industrial Hygiene AN INVESTIGATION OF THREE PROBLEMS CONCERNING THE ANALYSIS OF AIRBORNE ASPHALT FUMES A Thesis by LARRY T. LAIRD Approved as to style and content by: (Chairm of Committee) (Head of Department...

  8. ENCUENTRO EMPRESA-UNIVERSIDAD OPORTUNIDADES DE NEGOCIO EN EL MBITO DEL SECTOR INDUSTRIAL MARINO E

    E-Print Network [OSTI]

    Escolano, Francisco

    . Producción industrial de biomasa de insectos, mediante la valorización de subproductos de origen vegetal

  9. Life Cycle Assessment of Reclaimed Asphalt Pavement

    E-Print Network [OSTI]

    Minnesota, University of

    Life Cycle Assessment of Reclaimed Asphalt Pavement to Improve Asphalt Pavement Sustainability By Pavement (RAP) Courtesy of http://myconstructionphotos.smugmug.com/ RAP #12;Transport Back to the Plant-melt old binder on the RAP #12;Life Cycle Assessment (LCA) · #12;Asphalt Pavement Life Cycle Road

  10. Future Public Policy and Ethical Issues Facing the Agricultural and Microbial Genomics Sectors of the Biotechnology Industry: A Roundtable Discussion

    SciTech Connect (OSTI)

    Diane E. Hoffmann

    2003-09-12T23:59:59.000Z

    On September 12, 2003, the University of Maryland School of Law's Intellectual Property and Law & Health Care Programs jointly sponsored and convened a roundtable discussion on the future public policy and ethical issues that will likely face the agricultural and microbial genomics sectors of the biotechnology industry. As this industry has developed over the last two decades, societal concerns have moved from what were often local issues, e.g., the safety of laboratories where scientists conducted recombinant DNA research on transgenic microbes, animals and crops, to more global issues. These newer issues include intellectual property, international trade, risks of genetically engineered foods and microbes, bioterrorism, and marketing and labeling of new products sold worldwide. The fast paced nature of the biotechnology industry and its new developments often mean that legislators, regulators and society, in general, must play ''catch up'' in their efforts to understand the issues, the risks, and even the benefits, that may result from the industry's new ways of conducting research, new products, and novel methods of product marketing and distribution. The goal of the roundtable was to develop a short list of the most significant public policy and ethical issues that will emerge as a result of advances in these sectors of the biotechnology industry over the next five to six years. More concretely, by ''most significant'' the conveners meant the types of issues that would come to the attention of members of Congress or state legislators during this time frame and for which they would be better prepared if they had well researched and timely background information. A concomitant goal was to provide a set of focused issues for academic debate and scholarship so that policy makers, industry leaders and regulators would have the intellectual resources they need to better understand the issues and concerns at stake. The goal was not to provide answers to any of the issues or problems, simply to identify those topics that deserve our attention as a society. Some of the issues may benefit from legislation at the federal or state levels, others may be more appropriately addressed by the private sector. Participants at the roundtable included over a dozen experts in the areas of microbiology, intellectual property, agricultural biotechnology, microbial genomics, bioterrorism, economic development, biotechnology research, and bioethics. These experts came from federal and state government, industry and academia. The participants were asked to come to the roundtable with a written statement of the top three to five public policy/ ethical issues they viewed as most likely to be significant to the industry and to policy makers over the next several years.

  11. Industry

    SciTech Connect (OSTI)

    Bernstein, Lenny; Roy, Joyashree; Delhotal, K. Casey; Harnisch, Jochen; Matsuhashi, Ryuji; Price, Lynn; Tanaka, Kanako; Worrell, Ernst; Yamba, Francis; Fengqi, Zhou; de la Rue du Can, Stephane; Gielen, Dolf; Joosen, Suzanne; Konar, Manaswita; Matysek, Anna; Miner, Reid; Okazaki, Teruo; Sanders, Johan; Sheinbaum Parado, Claudia

    2007-12-01T23:59:59.000Z

    This chapter addresses past, ongoing, and short (to 2010) and medium-term (to 2030) future actions that can be taken to mitigate GHG emissions from the manufacturing and process industries. Globally, and in most countries, CO{sub 2} accounts for more than 90% of CO{sub 2}-eq GHG emissions from the industrial sector (Price et al., 2006; US EPA, 2006b). These CO{sub 2} emissions arise from three sources: (1) the use of fossil fuels for energy, either directly by industry for heat and power generation or indirectly in the generation of purchased electricity and steam; (2) non-energy uses of fossil fuels in chemical processing and metal smelting; and (3) non-fossil fuel sources, for example cement and lime manufacture. Industrial processes also emit other GHGs, e.g.: (1) Nitrous oxide (N{sub 2}O) is emitted as a byproduct of adipic acid, nitric acid and caprolactam production; (2) HFC-23 is emitted as a byproduct of HCFC-22 production, a refrigerant, and also used in fluoroplastics manufacture; (3) Perfluorocarbons (PFCs) are emitted as byproducts of aluminium smelting and in semiconductor manufacture; (4) Sulphur hexafluoride (SF{sub 6}) is emitted in the manufacture, use and, decommissioning of gas insulated electrical switchgear, during the production of flat screen panels and semiconductors, from magnesium die casting and other industrial applications; (5) Methane (CH{sub 4}) is emitted as a byproduct of some chemical processes; and (6) CH{sub 4} and N{sub 2}O can be emitted by food industry waste streams. Many GHG emission mitigation options have been developed for the industrial sector. They fall into three categories: operating procedures, sector-wide technologies and process-specific technologies. A sampling of these options is discussed in Sections 7.2-7.4. The short- and medium-term potential for and cost of all classes of options are discussed in Section 7.5, barriers to the application of these options are addressed in Section 7.6 and the implication of industrial mitigation for sustainable development is discussed in Section 7.7. Section 7.8 discusses the sector's vulnerability to climate change and options for adaptation. A number of policies have been designed either to encourage voluntary GHG emission reductions from the industrial sector or to mandate such reductions. Section 7.9 describes these policies and the experience gained to date. Co-benefits of reducing GHG emissions from the industrial sector are discussed in Section 7.10. Development of new technology is key to the cost-effective control of industrial GHG emissions. Section 7.11 discusses research, development, deployment and diffusion in the industrial sector and Section 7.12, the long-term (post-2030) technologies for GHG emissions reduction from the industrial sector. Section 7.13 summarizes gaps in knowledge.

  12. Industrial Sector Energy Conservation Programs in the People's Republic of China during the Seventh Five-Year Plan (1986-1990)

    E-Print Network [OSTI]

    Zhiping, L.

    2010-01-01T23:59:59.000Z

    energy demand. The energy consumption mix i n China'sstructure and product mix in energy-intensive industries;Table 4). The sector's mix of energy sources that year was

  13. Distributed Energy: Modeling Penetration in Industrial Sector Over the Long-Term

    E-Print Network [OSTI]

    Greening, L.

    2006-01-01T23:59:59.000Z

    -established industrial energy model, ITEMS (Industrial Technology and Energy Modeling System), and is calibrated to MECS 1994 and 1998. However, as compared to ITEMS, MARKAL is an optimization framework. And, this particular version of MARKAL has a forecast horizon...

  14. Evaluation of Efficiency Activities in the Industrial Sector Undertaken in Response to Greenhouse Gas Emission Reduction Targets

    E-Print Network [OSTI]

    Price, Lynn

    2010-01-01T23:59:59.000Z

    Fuels used in the refinery sector were also collected fromof the emissions from the refinery sector are included incommitment of 44% and the refinery and food sectors

  15. Profile of the rubber and plastics industry. EPA Office of Compliance sector notebook project

    SciTech Connect (OSTI)

    NONE

    1995-09-01T23:59:59.000Z

    The rubber and miscellaneous plastics products industry, as defined by the Standard Industrial Classification (SIC) code 30, includes establishments that manufacture products from plastic resins, natural and synthetic rubber, reclaimed rubber, futta percha, balata, and gutta siak. The second section provides background information on the size, geographic distribution, employment, production, sales, and economic condition of the Rubber and Plastics Products industry. The type of facilities described within the document are also described in terms of their Standard Industrial Classification (SIC) codes. Additionally, this section contains a list of the largest companies in terms of sales.

  16. Strategies for Low Carbon Growth In India: Industry and Non Residential Sectors

    E-Print Network [OSTI]

    Sathaye, Jayant

    2011-01-01T23:59:59.000Z

    essential to monitor and study energy consumption trends.and study energy consumption trends. E.S. 3. Industry Themonitor and study energy consumption trends. From a policy

  17. Unrestricted. Siemens AG 2013. All rights reserved.Page 2 October 2013 Corporate Technology Siemens is organized in 4 Sectors: Industry,

    E-Print Network [OSTI]

    Oak Ridge National Laboratory

    · Smart Grid · Building Technologies · Osram 2) Corporate functions Corporate Technology Corp. Finance Siemens is organized in 4 Sectors: Industry, Energy, Healthcare and Infrastructure & Cities Siemens: Facts ... Corp. Technology Corp. Development Infrastructure & Cities HealthcareEnergyIndustry ~ 14 bn.1) ~ 18 bn

  18. Rank Residential Sector Commercial Sector Industrial Sector

    Gasoline and Diesel Fuel Update (EIA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for On-Highway4,1,50022,3,,,,6,1,9,1,50022,3,,,,6,1,Decade Energy I I' a evie _ =_ In7, 20116,650.0 Weekly7a.7. Petroleum and3.

  19. Successful public sector enforcement of environmental standards in the Toritama Jeans industry in Pernambuco, Brazil

    E-Print Network [OSTI]

    Lazarte, Maria Ella J

    2005-01-01T23:59:59.000Z

    Non-observance of environmental standards among small firms in traditional industries such as garment, footwear, furniture and tanneries have caused major environmental degradation in many places throughout the world. ...

  20. The Importance of Natural Gas in the Industrial Sector With a Focus on Energy-Intensive Industries

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere IRaghuraji Agro IndustriesTownDells,1Stocks Nov-14Total DeliveredPrincipalNumberAugust7,Biofuels:

  1. Model documentation report: Industrial sector demand module of the national energy modeling system

    SciTech Connect (OSTI)

    NONE

    1998-01-01T23:59:59.000Z

    This report documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Industrial Demand Model. The report catalogues and describes model assumptions, computational methodology, parameter estimation techniques, and model source code. This document serves three purposes. First, it is a reference document providing a detailed description of the NEMS Industrial Model for model analysts, users, and the public. Second, this report meets the legal requirements of the Energy Information Administration (EIA) to provide adequate documentation in support of its model. Third, it facilitates continuity in model development by providing documentation from which energy analysts can undertake model enhancements, data updates, and parameter refinements as future projects.

  2. A State Regulator's View of 'PURPA' And Its Impact on Energy Conservation in the Industrial Sector

    E-Print Network [OSTI]

    Williams, M. L.

    1981-01-01T23:59:59.000Z

    improving utility production efficiency, lowering costs and possibly reducing the need for new high cost production facilities. On the other hand, time of use rates may ultimately cause some electric users, especially certain large industrial customers... and resources by electric utilities." Two types of efficiency are addressed here. The first, is economic efficiency, which in classical economics implies the setting of prices which result in the appropriate allocation and conservation of society...

  3. Asphalt deposition in miscible floods

    E-Print Network [OSTI]

    Hasan, Syed Mir Ahmed

    1964-01-01T23:59:59.000Z

    : Petroleum Engineering ASPHALT DEPOSITION IN MISCIBLE FLOODS A Thesis By SYED MIR AHMED HASAN Approved as to style and content by: (Chairman of Committee) ommittee Member) Committee Member) Head of Department), (Co 'ttee Member) January, f964... Subject: Petroleum Engineering TABLE OF CONTENTS ABS TRAC T. Page 2. INTRODUCTION. 3 DESCRIPTION OF EQUIPMENT AND MATERIALS. . . . . , . 6 4. EXPERIMENTAL PROCEDURE 5. INTERPRETATION AND DISCUSSION OF RESULTS. . . . . . 13 6. CONCLUSIONS. 7...

  4. Winter Performance and Maintenance of Porous Asphalt Pavements

    E-Print Network [OSTI]

    Concrete (HSG-B)Porous Asphalt (HSG-C) #12;Cold Climate Performance Results #12;12 Porous Asphalt SurfaceWinter Performance and Maintenance of Porous Asphalt Pavements Robert M. Roseen, Ph.D., P.E., D impacts for new development and reverse impacts in areas with redevelopment. #12;Porous Asphalt Design

  5. Compatibilizer for crumb rubber modified asphalt

    SciTech Connect (OSTI)

    Labib, M.E. [New Jersey Institute of Technology, Newark, NJ (United States); Memon, G.M.; Chollar, B.H. [Federal Highway Administration, McLean, VA (United States)

    1996-12-31T23:59:59.000Z

    The United States of America discards more than 300 million tires each year, and out of that a large fraction of the tires is dumped into stock piles. This large quantity of tires creates an environmental problem. The use of scrap tires is limited. There is a usage potential in such fields as fuel for combustion and Crumb Rubber-Modified Asphalt binder (CRMA). The use of crumb rubber in modifying asphalt is not a new technique; it is been used since early 1960 by pavement engineers. Crumb rubber is a composite of different blends of natural and synthetic rubber (natural rubber, processing oils, polybutadiene, polystyrene butadiene, and filler). Prior research had concluded that the performance of crumb rubber modified asphalt is asphalt dependent. In some cases it improves the Theological properties and in some cases it degrades the properties of modified asphalt.

  6. Materials characterization of asphalt and polymer modified asphalt 

    E-Print Network [OSTI]

    Paramasivam, Mohan

    1992-01-01T23:59:59.000Z

    specimen mold made of aluminum ? ? ? ? ? ? ? ? ? ? - 28 5. Strain sweep of Santa Maria AC10/AR4000 at 100 rad/sec --- 33 6. Strain sweep of Conoco AC10 at 10 rad/sec ------------- 34 7. Stress relaxation modulus of AAM grade asphalt at 25'C --- 37 8.... The verification of Cox-Merz rule for Santa Maria AC6/AR2000 at 40'C- 9. The master curve of Santa Maria AC6/Muehlstein LDPE shifted to 25'C showing the errors 10. Master curve (G') of Santa Maria AC6 shifted to 25'C ? ? ? ? ? 43 11. Master curve of Santa...

  7. Materials characterization of asphalt and polymer modified asphalt

    E-Print Network [OSTI]

    Paramasivam, Mohan

    1992-01-01T23:59:59.000Z

    specimen mold made of aluminum ? ? ? ? ? ? ? ? ? ? - 28 5. Strain sweep of Santa Maria AC10/AR4000 at 100 rad/sec --- 33 6. Strain sweep of Conoco AC10 at 10 rad/sec ------------- 34 7. Stress relaxation modulus of AAM grade asphalt at 25'C --- 37 8.... The verification of Cox-Merz rule for Santa Maria AC6/AR2000 at 40'C- 9. The master curve of Santa Maria AC6/Muehlstein LDPE shifted to 25'C showing the errors 10. Master curve (G') of Santa Maria AC6 shifted to 25'C ? ? ? ? ? 43 11. Master curve of Santa...

  8. Development of superior asphalt recycling agents. Phase 1, Technical feasibility. Final technical progress report

    SciTech Connect (OSTI)

    Bullin, J.A.; Davison, R.R.; Glover, C.J.; Chaffin, J.; Liu, M.; Madrid, R.

    1997-07-01T23:59:59.000Z

    After an introduction and a literature survey in Chap. 1, Chap. 2 describes the tasks, together with objectives and important results obtained for each task throughout the entire project. Chaps. 3 thru 7 detail work in developing a qualitative and quantitative knowledge of asphalt oxidation, composition dependence of asphalt properties, and guidelines for producing superior asphalt binders through composition control. They also detail the development of a kinetic model for asphalt oxidative aging and present an understanding of the composition dependence of asphalt oxidation as well as other performance-related properties. Chaps. 8 and 9 compare the aging performance of recycled blends produced using commercial recycling agents and industrial supercritical fractions as rejuvenating agents. Oxidative aging of the recycled blends were evaluated along with the performance of the recycled blends in terms of the strategic highway research program performance grading procedure. Chap. 10 summarizes the work completed in the areas of processing schemes development, projection updates, and scale-up and commercialization plans.

  9. Evaluation of Efficiency Activities in the Industrial Sector Undertaken in Response to Greenhouse Gas Emission Reduction Targets

    E-Print Network [OSTI]

    Price, Lynn

    2010-01-01T23:59:59.000Z

    update to the California Energy Balance (LBNL, forthcoming). The comparison shows that Denmark’s manufacturing sector

  10. Analysis of Energy Use in Building Services of the Industrial Sector in California: A Literature Review and a Preliminary Characterization

    E-Print Network [OSTI]

    Akbari, H.

    2008-01-01T23:59:59.000Z

    Heavy industries (such as smelting, oil refining, glass andheavy industry (e.g. , iron and steel, oil refining, and

  11. Sector-specific issues and reporting methodologies supporting the General Guidelines for the voluntary reporting of greenhouse gases under Section 1605(b) of the Energy Policy Act of 1992. Volume 1: Part 1, Electricity supply sector; Part 2, Residential and commercial buildings sector; Part 3, Industrial sector

    SciTech Connect (OSTI)

    Not Available

    1994-10-01T23:59:59.000Z

    DOE encourages you to report your achievements in reducing greenhouse gas emissions and sequestering carbon under this program. Global climate change is increasingly being recognized as a threat that individuals and organizations can take action against. If you are among those taking action, reporting your projects may lead to recognition for you, motivation for others, and synergistic learning for the global community. This report discusses the reporting process for the voluntary detailed guidance in the sectoral supporting documents for electricity supply, residential and commercial buildings, industry, transportation, forestry, and agriculture. You may have reportable projects in several sectors; you may report them separately or capture and report the total effects on an entity-wide report.

  12. Evaluation of Efficiency Activities in the Industrial Sector Undertaken in Response to Greenhouse Gas Emission Reduction Targets

    E-Print Network [OSTI]

    Price, Lynn

    2010-01-01T23:59:59.000Z

    example, the chemical and petrochemical sectors use largeoil (US EIA, 2009a), petrochemical fuel use (US EIA, 2009b)Metallic Minerals Chemical and Petrochemical Primary Metals

  13. Rapid determination of actinides in asphalt samples

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Maxwell, Sherrod L.; Culligan, Brian K.; Hutchison, Jay B.

    2014-01-12T23:59:59.000Z

    A new rapid method for the determination of actinides in asphalt samples has been developed that can be used in emergency response situations or for routine analysis If a radiological dispersive device (RDD), Improvised Nuclear Device (IND) or a nuclear accident such as the accident at the Fukushima Nuclear Power Plant in March, 2011 occurs, there will be an urgent need for rapid analyses of many different environmental matrices, including asphalt materials, to support dose mitigation and environmental clean up. The new method for the determination of actinides in asphalt utilizes a rapid furnace step to destroy bitumen and organicsmore »present in the asphalt and sodium hydroxide fusion to digest the remaining sample. Sample preconcentration steps are used to collect the actinides and a new stacked TRU Resin + DGA Resin column method is employed to separate the actinide isotopes in the asphalt samples. The TRU Resin plus DGA Resin separation approach, which allows sequential separation of plutonium, uranium, americium and curium isotopes in asphalt samples, can be applied to soil samples as well.« less

  14. Rapid determination of actinides in asphalt samples

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Maxwell, Sherrod L.; Culligan, Brian K.; Hutchison, Jay B.

    2014-01-12T23:59:59.000Z

    A new rapid method for the determination of actinides in asphalt samples has been developed that can be used in emergency response situations or for routine analysis If a radiological dispersive device (RDD), Improvised Nuclear Device (IND) or a nuclear accident such as the accident at the Fukushima Nuclear Power Plant in March, 2011 occurs, there will be an urgent need for rapid analyses of many different environmental matrices, including asphalt materials, to support dose mitigation and environmental clean up. The new method for the determination of actinides in asphalt utilizes a rapid furnace step to destroy bitumen and organics present in the asphalt and sodium hydroxide fusion to digest the remaining sample. Sample preconcentration steps are used to collect the actinides and a new stacked TRU Resin + DGA Resin column method is employed to separate the actinide isotopes in the asphalt samples. The TRU Resin plus DGA Resin separation approach, which allows sequential separation of plutonium, uranium, americium and curium isotopes in asphalt samples, can be applied to soil samples as well.

  15. An investigation of the use of tire rubber in asphalt

    E-Print Network [OSTI]

    Koo, Heamo Lee

    1996-01-01T23:59:59.000Z

    -rubber binder. The selected variables chosen are curing time, curing temperature, rubber content (weight percent), rubber particle size, base asphalt type, and carbonyl area. Results confirmed that the addition of rubber increased the viscosity of the asphalt...

  16. asphalt composition aplicacao: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Warm mix asphalt (WMA) is not a hot mix asphalt (HMA), it's just warm mix The WMA production temperature typically ranges from 100 to 140o C, whereas for HMA it ranges Das,...

  17. Moisture Diffusion in Asphalt Binders and Fine Aggregate Mixtures

    E-Print Network [OSTI]

    Vasconcelos, Kamilla L.

    2011-08-08T23:59:59.000Z

    cost in highway maintenance and vehicle operations. One key mechanism of how moisture reaches the asphalt-aggregate interface is by its permeation or diffusion through the asphalt binder or mastic. Different techniques are available for diffusion...

  18. Controlling Thermal Properties of Asphalt Concrete and its Multifunctional Applications 

    E-Print Network [OSTI]

    Shi, Xijun

    2014-08-10T23:59:59.000Z

    ) by controlling thermal properties of the construction materials. To change thermal properties of asphalt concrete, expanded polypropylene (EPP) pellet and graphite were selected as the additives and mixed into asphalt concrete. Experimental tests are classified...

  19. Damage analysis in asphalt concrete mixtures based on parameter relationships 

    E-Print Network [OSTI]

    Song, Injun

    2004-11-15T23:59:59.000Z

    Asphalt pavements experience damage due to traffic loading under various environmental conditions. Damage can be caused by viscopl microcracks, fracture due to fatigue cracking, or fracture due to thermal cracking. Asphalt ...

  20. Evaluation of Rexene polymers in hot mixed asphalt concrete 

    E-Print Network [OSTI]

    Rodriguez, Mary Anne Reese

    1991-01-01T23:59:59.000Z

    Committee: Dr. Dallas N. Little The objective of this research was to provide a comprehensive characterization of asphalt binders and paving mixtures modified with four polymers produced by the Rexene Products Company (Odessa, Texas). The four polymers... LITERATURE REVIEW AND INTERPRETATION General Available Asphalt Additives Practical Application of Asphalt Additives Benefit-Costs for Additives Future Outlook for Additives MATERIALS AND TEST METHODS Polymers Asphalt Cements Aggregate Procedure...

  1. Disk-shaped Compact Tension Test for Asphalt Concrete Fracture

    E-Print Network [OSTI]

    Paulino, Glaucio H.

    Disk-shaped Compact Tension Test for Asphalt Concrete Fracture by M.P.Wagoner, W.G. Buttlar and G geometry is the ability to test cylindrical cores obtained from in-place asphalt concrete pavements finalizing the specimen geometry, a typical asphalt concrete surface mixture was tested at various

  2. Asphalt Pavement Aging and Temperature Dependent Properties through a Functionally

    E-Print Network [OSTI]

    Paulino, Glaucio H.

    Asphalt Pavement Aging and Temperature Dependent Properties through a Functionally Graded ­ Verification ­ Concluding Remarks Part ­ II (Companion presentation) ­ Asphalt Pavements ­ Effect of Aging: Asphalt concrete pavements (Part II) E1 E2 E3 Eh 1 2 3 h #12;Graded Finite Elements Graded Elements

  3. Evaluation of Efficiency Activities in the Industrial Sector Undertaken in Response to Greenhouse Gas Emission Reduction Targets

    E-Print Network [OSTI]

    Price, Lynn

    2010-01-01T23:59:59.000Z

    Administration, 2009c. EIA-906/920 Database: Monthly UtilityEIA), 2009. Form EIA-906/920 Database: Monthly Utility andEIA power sector annual database (EIA, 2009) and converting

  4. Bottom-up Representation of Industrial Energy Efficiency Technologies in Integrated Assessment Models for the Cement Sector

    E-Print Network [OSTI]

    Sathaye, J.

    2011-01-01T23:59:59.000Z

    Technology Support Unit (ETSU), 1988. “High Level Control ofCircle Industries and SIRA (ETSU, 1988). The LINKman system

  5. What's the future for rubberized asphalt

    SciTech Connect (OSTI)

    Not Available

    1991-04-01T23:59:59.000Z

    This article describes the debate over the use of rubberized asphalt for highway surfacing. The Department of Transportation claims that the process is too costly; that it presents potential air pollution, safety and health problems. They also claim that there is a lack of understanding between rubber and asphalt cement and of the recyclability of the product. The Legislative Commission on Solid Waste Management claims that the mixture performs as well or better than conventional asphalt at reduced thicknesses. In addition, there could be savings of local funds currently expended for regulation of tire dumps, fire-fighting and clean-up, vector control and scrap tire disposal costs ranging from $.50 to $2.00 per tire.

  6. The potential use of tar sand bitumen as paving asphalt

    SciTech Connect (OSTI)

    Petersen, J.C.

    1988-01-01T23:59:59.000Z

    In this paper several research reports describing the preparation of potential paving asphalts from tar sand bitumen are reviewed and the results of the studies compared. The tar sand asphalts described in the studies were prepared from 1) hot water-recovered bitumen from deposits near San Luis Obispo, California (Edna deposits), and deposits near Vernal and Sunnyside, Utah; and 2) bitumen recovered from the Northwest Asphalt Ridge deposits near Vernal, Utah, by both in situ steamflood and in situ combustion recovery processes. Important properties of the tar sand asphalts compare favorably with those of specification petroleum asphalts. Laboratory data suggest that some tar sand asphalts may have superior aging characteristics and produce more water-resistant paving mixtures than typical petroleum asphalts.

  7. The potential use of tar sand bitumen as paving asphalt

    SciTech Connect (OSTI)

    Petersen, J.C.

    1987-01-01T23:59:59.000Z

    The properties of several tar sand asphalts prepared in past studies by several different investigators were compared with each other and with the properties of petroleum asphalts. These results were reviewed and discussed with regard to the potential use of tar sand bitumen in pavement applications. The data show that tar sand bitumen has good potential for use in highway pavements that meet today's performance specifications. No deficiencies in the tar sand asphalts were found that would be expected to seriously affect performance. On the other hand, the data indicate that some tar sand asphalts may have superior aging characteristics, being relatively resistant to oxidative age hardening compared with typical petroleum asphalts. Asphalt-aggregate mixtures prepared using two tar sand asphalts also showed acceptable strength properties and excellent resistance to moisture-induced damage.

  8. Evaluation of polyethylene-modified asphalt blends

    E-Print Network [OSTI]

    Consuegra Granger, Fernando

    1990-01-01T23:59:59.000Z

    aggregate and asphalt modified with LDPE (binder contents of 4. 8%%u and 5. 87'). 42 Table 9. Summary of statistical parameters derived from IDT testing on crushed granite mixtures bound with AC-20 + LDPE (4. 8%, and 5. 8/ binder). 46 Table 10. Summary... of creep to rupture data for crushed granite mixtures. 71 Table 11. Summary of the results of IDT repeated load fatigue testing of river gravel mixtures bound with Texaco asphalt: AC- 10, AC-10 + LDPE and AC-20. Table 12. K, ' and n, values of river...

  9. Evaluation of Efficiency Activities in the Industrial Sector Undertaken in Response to Greenhouse Gas Emission Reduction Targets

    E-Print Network [OSTI]

    Price, Lynn

    2010-01-01T23:59:59.000Z

    chemicals, light industry (iron foundries, cold storage andindustry ? Use of CHP ? Debottlenecking ? Increased production capacity ? Better use of production capacity ? Energy management Cold storage

  10. Evaluation of Efficiency Activities in the Industrial Sector Undertaken in Response to Greenhouse Gas Emission Reduction Targets

    E-Print Network [OSTI]

    Price, Lynn

    2010-01-01T23:59:59.000Z

    industry (iron foundries, cold storage and refrigeration,Energy management Cold storage and refrigeration ? Newelectric power; heat/cold storage; heat pumps using ambient

  11. Evaluation of Efficiency Activities in the Industrial Sector Undertaken in Response to Greenhouse Gas Emission Reduction Targets

    E-Print Network [OSTI]

    Price, Lynn

    2010-01-01T23:59:59.000Z

    energy monitoring system Paper and Paperboard industry ? Integrated energy management system ?monitoring was handled by “accredited organizations that certify the energy management systems” (

  12. The effect of asphalt deposition on recovery of oil by a pentane slug

    E-Print Network [OSTI]

    Bhagia, Nanik S

    1965-01-01T23:59:59.000Z

    ":ty reduction increases, in general, with the increase in amount of, asphalt contained ir the oil. The increases in recovery at breakthrough due to asphalt deposition were noted for four asphaltic crude oils and were compared to those of asphalt-free refined... substantial range, the gain in recovery at breakthrough of asphaltic oils over refined oils of the same viscosity increases with increase in size of slug used. This is attributed to more favorable mobility ratios resulting from asphalt deposition during...

  13. Evaluation of Efficiency Activities in the Industrial Sector Undertaken in Response to Greenhouse Gas Emission Reduction Targets

    E-Print Network [OSTI]

    Price, Lynn

    2010-01-01T23:59:59.000Z

    to provide training and energy audits and to help industrial1997 to end of March - Energy audits have allow to avoidagrees to undertake an energy audit, develop a management

  14. Analysis of Energy Use in Building Services of the Industrial Sector in California: A Literature Review and a Preliminary Characterization

    E-Print Network [OSTI]

    Akbari, H.

    2008-01-01T23:59:59.000Z

    by ERC, is 448.3 trillion Btu (TBtu). The total CaliforniaBecause the cost of an electrical Btu is roughly 4 timesthat of a source fuel Btu, industrial categories that use

  15. Asphalt Pavement Aging and TemperatureAsphalt Pavement Aging and Temperature Dependent Properties using a FunctionallyDependent Properties using a Functionally

    E-Print Network [OSTI]

    Paulino, Glaucio H.

    Asphalt Pavement Aging and TemperatureAsphalt Pavement Aging and Temperature Dependent Properties Analysis Time Integration Analysis Application Examples: Asphalt Pavement Summary and Conclusions #12) ­ Large fraction produced as hot-mix asphalt (HMA) ­ Most common form of pavement surfacing material (96

  16. Investigation of Noise and Durability Performance Trends for Asphaltic Pavement Surface Types: Three-Year Results

    E-Print Network [OSTI]

    Lu, Qing; Kohler, Erwin R.; Harvey, John T; Ongel, Aybike

    2009-01-01T23:59:59.000Z

    Trends for Asphalt Pavement Surface Types: First- andResults. University of California Pavement Research Center,Trends for Asphaltic Pavement Surface Types: First- and

  17. A novel technique for the production of cool colored concrete tile and asphalt shingle roofing products

    E-Print Network [OSTI]

    Levinson, Ronnen

    2010-01-01T23:59:59.000Z

    for providing concrete tiles, and Lou Hahn of GAF-Elk forof cool colored concrete tile and asphalt shingle roofingsolar-reflective nonwhite concrete tile and asphalt shingle

  18. Industry

    E-Print Network [OSTI]

    Bernstein, Lenny

    2008-01-01T23:59:59.000Z

    SHIP - Solar heat for industrial processes. Internationalsolar power could be used to provide process heat for

  19. OTHER INDUSTRIES

    Broader source: Energy.gov [DOE]

    AMO funded research results in novel technologies in diverse industries beyond the most energy intensive ones within the U.S. Manufacturing sector. These technologies offer quantifiable energy...

  20. Predicting the fatigue life of asphalt concrete overlay systems

    E-Print Network [OSTI]

    Germann, Frederick P

    1979-01-01T23:59:59.000Z

    ON CRACK GROWTH IN VISCOELASTIC MATERIALS C'HAPTER V - STATE OF THE ART Effect of Mix Variables on Fatigue and Cracking Resistance in Asphalt Concrete Pavements . Field Performance of Asphalt Overlays with Fabric Summary CHAPTER VI ? MATERIALS... LIFE OF AN ASPHALT OVERLAY CHAPTER X - CONCLUSIONS AND RECOMMENDATIONS REFERENCES APPENDIX A. CRACK TIP STRESS ANALYSIS APPENDIX B. CONSTRUCTION OF THE MASTER RESILIENT MODULUS AND MASTER CREEP COMPLIANCE CURVES APPENDIX C. CRACK GROWTH RATES, da...

  1. Microstructural Characterization of Material Properties and Damage in Asphalt Composites

    E-Print Network [OSTI]

    Mohammad Khorasani, Sara

    2013-05-03T23:59:59.000Z

    MICROSTRUCTURAL CHARACTERIZATION OF MATERIAL PROPERTIES AND DAMAGE IN ASPHALT COMPOSITES A Thesis by SARA MOHAMMAD KHORASANI Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment... Engineering Copyright 2013 Sara Mohammad Khorasani ii ABSTRACT Asphalt composites are used to construct 90% of roads in the United States. These composites consist of asphalt binder, which is a product of the refinery process of oil, aggregates...

  2. Public/private sector cooperation to promote industrial energy efficiency: Allied partners and the US Department of Energy

    SciTech Connect (OSTI)

    McKane, Aimee; Cockrill, Chris; Tutterow, Vestal; Radspieler, Anthony

    2003-05-18T23:59:59.000Z

    Since 1996, the US Department of Energy's Office of Industrial Technologies (USDOE) has been involved in a unique voluntary collaboration with industry called the Allied Partner program. Initially developed under the Motor Challenge program, the partnership concept continues as a central element of USDOE's BestPractices, which in 2001 integrated all of USDOE's near-term industrial program offerings including those in motors, compressed air, pump, fan, process heating and steam systems. Partnerships are sought with end use industrial companies as well as equipment suppliers and manufacturers, utilities, consultants, and state agencies that have extensive existing relationships with industrial customers. Partners are neither paid nor charged a fee for participation. Since the inception of Allied Partners, the assumption has been that these relationships could serve as the foundation for conveying a system energy-efficiency message to many more industrial facilities than could be reached through a typical government-to-end-user program model. An independent evaluation of the Motor Challenge program, reported at the last EEMODS conference, attributed US $16.9 million or nearly 67 percent of the total annual program energy savings to the efforts of Allied Partners in the first three years of operation. A recent evaluation of the Compressed Air Challenger, which grew out of the former Motor Challenger program, attribute additional energy savings from compressed air training alone at US $12.1 million per year. Since the reorganization under BestPractices, the Allied Partner program has been reshaped to extend the impact of all BestPractices program activities. This new model is more ambitious than the former Motor Challenge program concerning the level of collaborative activities negotiated with Allied Partners. This paper describes in detail two new types of program initiatives involving Allied Partners: Qualified Specialist Training and Energy Events. The Qualified Specialist activity was conceived as a way of engaging the supply side of industry, consultants, and utilities to greatly increase use of decision making software developed by USDOE to assist industrial facilities in assessing the energy efficiency of their energy-using systems. To date, USDOE has launched Qualified Specialist training with member companies of the Hydraulic Institute (HI) and with distributors and consultants associated with the Compressed Air Challenge. These activities train and qualify industry professionals to use and to train customers to use USDOE's Pumping System Assessment Tool (PSAT) and AIRMaster + software programs, respectively. The industry experts provide a public benefit by greatly increasing customer access to the software and assessment techniques. Participating Specialists anticipate a business benefit by providing a valuable service to key customers that is associated with USDOE. The Energy Event concept was developed in 2001 in cooperation with the California Energy Commission in response to the state's energy crisis and has been extended to other geographic areas during 2002. The three California events, named ''Energy Solutions for California Industry,'' relied on Allied Partners to provide system-based solutions to industrial companies as both speakers and exhibitors. These one-day events developed a model for a serious solutions-oriented format that avoids the typical trade show atmosphere through strict exhibitor guidelines, careful screening of speaker topics, and reliance on case studies to illustrate cost- and energy-saving opportunities from applying a systems approach. Future plans to use this activity model are discussed as well as lessons learned from the California series.

  3. asphalt technology test: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and evaluated its performance when used in split mastic asphalt (SMA) mixture using Marshall Characteristic and dynamic charateristics (resilient modulus). As many as 90...

  4. anionic emulsified asphalt: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    to Volucm Change... Gandhi, Poduru Mohandas Karamchand 1966-01-01 15 Life Cycle Assessment of Reclaimed Asphalt Pavement Energy Storage, Conversion and Utilization Websites...

  5. asphalt rock: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Corrections to Volucm Change... Gandhi, Poduru Mohandas Karamchand 1966-01-01 17 Life Cycle Assessment of Reclaimed Asphalt Pavement Energy Storage, Conversion and Utilization...

  6. asphaltic sand: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Corrections to Volucm Change... Gandhi, Poduru Mohandas Karamchand 1966-01-01 19 Life Cycle Assessment of Reclaimed Asphalt Pavement Energy Storage, Conversion and Utilization...

  7. asphalt concrete overlays: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    experimental results for concrete containing virgin limestone Paulino, Glaucio H. 71 Life Cycle Assessment of Reclaimed Asphalt Pavement Energy Storage, Conversion and Utilization...

  8. asphalt overlay design: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    these overlay networks. Routing and search in these overlay ... Cheng, Bow-Nan 69 Life Cycle Assessment of Reclaimed Asphalt Pavement Energy Storage, Conversion and Utilization...

  9. asphalt binder extraction: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Corrections to Volucm Change... Gandhi, Poduru Mohandas Karamchand 1966-01-01 43 Life Cycle Assessment of Reclaimed Asphalt Pavement Energy Storage, Conversion and Utilization...

  10. Full-Depth Pavement Reclamation with Foamed Asphalt: Final Report

    E-Print Network [OSTI]

    Jones, David; Fu, P.; Harvey, John T; Halles, F.

    2008-01-01T23:59:59.000Z

    University of California Pavement Research Center. (WP-2005-8 th Conference on Asphalt Pavements for Southern Africa (International Journal of Pavement Engineering, Vol 8, No

  11. asphalt concrete bases: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    large amounts of PS wastes in civil engineering constructions. Key words: Asphalt surfaces Disposable dishes Polystyrene (PS) Wastes Environment A. Akbari Motlagh; A....

  12. asphalt concrete soil: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    large amounts of PS wastes in civil engineering constructions. Key words: Asphalt surfaces Disposable dishes Polystyrene (PS) Wastes Environment A. Akbari Motlagh; A....

  13. Analysis of Energy Use in Building Services of the Industrial Sector in California: A Literature Review and a Preliminary Characterization

    E-Print Network [OSTI]

    Akbari, H.

    2008-01-01T23:59:59.000Z

    industry or plants could benefit from new technologies such as cold storagecold storage and space cooling systems technology has. The electricity use in these industriesindustries may also be able to take advan- tage of TES; however, the technology of integrating cold storage

  14. Industry

    E-Print Network [OSTI]

    Bernstein, Lenny

    2008-01-01T23:59:59.000Z

    oil, starch and corn refining, since these can be a source of fuel products. The sugar cane industry

  15. Compositional evaluation of asphalt binder recycling agents

    E-Print Network [OSTI]

    Madrid, Richard Charles

    1997-01-01T23:59:59.000Z

    from: Exxon Research and Engineering Company, The National Consortium for Graduate Degrees for Minorities in Engineering and Science, Inc. Fellowship (GEM), and the DOW Technical Fellowship is greatly appreciated. I thank Sophie and Ignacio Madrid... for Recycled Blends . . . . . Asphaltic Materials. . 54 58 63 69 V-2 V-3 V-4 V-5 V-6 V-7 Fina DMO and Exxon Tank Compositions and Viscosities. . . . Blend Compositions and Viscosities...

  16. The DOE s In-Plant Training (INPLT) Model to Promote Energy Efficiency in the Industrial Sector

    SciTech Connect (OSTI)

    Alkadi, Nasr E [ORNL] [ORNL; Nimbalkar, Sachin U [ORNL] [ORNL; De Fontaine, Mr. Andre [United States Department of Energy (DOE), Industrial Technology Program] [United States Department of Energy (DOE), Industrial Technology Program; Schoeneborn, Fred C [ORNL] [ORNL

    2013-01-01T23:59:59.000Z

    In-Plant Training (INPLT) is a new model for developing energy efficiency expertise within the US manufacturing companies participating in the U.S. Department of Energy s (DOE s) Better Buildings, Better Plants Program-a nationwide initiative to drive a 25% reduction in industrial energy intensity in 10 years. INPLTs are designed to fill a market niche by providing hands on training in a real world manufacturing plant environment. Through INPLTs, participants from multiple manufacturing plants, supply chains, utilities, and other external stakeholders learn how to conduct energy assessments, use energy analysis tools to analyze energy saving opportunities, develop energy management systems, and implement energy savings projects. Typical INPLT events are led by DOE-certified Energy Experts and range from 2-4 days. Topics discussed include: identification of cross-cutting or system specific opportunities; introduction to ISO 50001 Energy Management Systems; and energy project implementation and replication. This model is flexible, and can be tailored to suit the needs of specific industries. The INPLTs are a significant departure from the traditional single plant energy assessment model previously employed by DOE. INPLTs shift the focus from the concept of a single-plant s energy profile to a broader focus on training and capacity building among multiple industrial participants. The objective is to enable trainees to identify, quantify, implement and replicate future energy saving projects without continued external assistance. This paper discusses the INPLT model and highlights some of the initial outcomes from the successfully delivered INPLTs and the overall impact in terms of numbers of plants/participants trained, impacted energy footprints, and potential replication of identified opportunities.

  17. Rheological Investigation of the Influence of Acrylate Polymers on the Modification of Asphalt

    E-Print Network [OSTI]

    Hussein, Ibnelwaleed A.

    and superior ACM properties when blended with the high asphaltenes Arabian asphalt. © 2006 Wiley Periodicals

  18. Recycled rubber, aggregate, and filler in asphalt paving mixtures. Transportation research record

    SciTech Connect (OSTI)

    NONE

    1996-12-31T23:59:59.000Z

    ;Contents(Partial): Evaluation Systems for Crumb Rubber Modified Binders and Mixtures; Hot Mix Asphalt Rubber Applications in Virginia; Evaluation of Pyrolized Carbon Black from Scrap Tires as Additive in Hot Mix Asphalt; Use of Scrap Tire Chips in Asphaltic Membrane; Effects of Mineral Fillers on Properties of Stone Matrix Asphalt Mixtures; and Quantitative Analysis of Aggregate Based on Hough Transform.

  19. Field Manual for Crack Sealing in Asphalt Pavements

    E-Print Network [OSTI]

    Texas at Austin, University of

    Field Manual for Crack Sealing in Asphalt Pavements Yetkin Yildirim, Ahmed Qatan, and Jorge Prozzi January 2006 3208RedRiver Austin,TX78705 #12;Dr. Yetkin Yildirim, P.E. Director Texas Pavement for Crack Sealing in Asphalt Pavements #12;Performing Organization: Center for Transportation Research

  20. Recycling asphalt overview of more than 25 years of use

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    1 Recycling asphalt overview of more than 25 years of use in France Y. Brosseaud ­ LCPC hal with ring for recycling ­ Average rate with high proportion : 30 to 50% ­ Used of rejuvenators (soft oil,version1-20May2011 #12;4 Hot recycling asphalt on mixing plant Recycling in place in hot or cold

  1. U.S. Energy Information Administration (EIA) - Sector

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    Industrial sector energy demand On This Page Heat and power energy... Industrial fuel mix changes... Iron and steel... Delivered energy use... Chemical industry use of fuels......

  2. U.S. Energy Information Administration (EIA) - Sector

    Gasoline and Diesel Fuel Update (EIA)

    Industrial sector energy demand Manufacturing heat and power energy consumption increases modestly figure data Despite a 49-percent increase in industrial shipments, industrial...

  3. U.S. Energy Information Administration (EIA) - Sector

    Gasoline and Diesel Fuel Update (EIA)

    Industrial sector energy demand Growth in industrial energy consumption is slower than growth in shipments figure data Despite a 76-percent increase in industrial shipments,...

  4. Industry

    E-Print Network [OSTI]

    Bernstein, Lenny

    2008-01-01T23:59:59.000Z

    of its electricity requirements in the USA (US DOE, 2002)USA, where motor-driven systems account for 63% of industrial electricity

  5. Bottom-up Representation of Industrial Energy Efficiency Technologies in Integrated Assessment Models for the Cement Sector

    SciTech Connect (OSTI)

    Sathaye, J.; Xu, T.; Galitsky, C.

    2010-08-15T23:59:59.000Z

    Adoption of efficient end-use technologies is one of the key measures for reducing greenhouse gas (GHG) emissions. How to effectively analyze and manage the costs associated with GHG reductions becomes extremely important for the industry and policy makers around the world. Energy-climate (EC) models are often used for analyzing the costs of reducing GHG emissions for various emission-reduction measures, because an accurate estimation of these costs is critical for identifying and choosing optimal emission reduction measures, and for developing related policy options to accelerate market adoption and technology implementation. However, accuracies of assessing of GHG-emission reduction costs by taking into account the adoption of energy efficiency technologies will depend on how well these end-use technologies are represented in integrated assessment models (IAM) and other energy-climate models.

  6. Relationship Between Surface Free Energy and Total Work of Fracture of Asphalt Binder and Asphalt Binder-Aggregate Interfaces 

    E-Print Network [OSTI]

    Howson, Jonathan Embrey

    2012-10-19T23:59:59.000Z

    is the surface free energy of the asphalt binder and the aggregate. Surface free energy, which is a thermodynamic material property, is directly related to the adhesive bond energy between the asphalt binder and the aggregate as well as the cohesive bond energy...

  7. Relationship Between Surface Free Energy and Total Work of Fracture of Asphalt Binder and Asphalt Binder-Aggregate Interfaces

    E-Print Network [OSTI]

    Howson, Jonathan Embrey

    2012-10-19T23:59:59.000Z

    is the surface free energy of the asphalt binder and the aggregate. Surface free energy, which is a thermodynamic material property, is directly related to the adhesive bond energy between the asphalt binder and the aggregate as well as the cohesive bond energy...

  8. Industrial Energy Efficiency: Designing Effective State Programs...

    Energy Savers [EERE]

    Industrial Energy Efficiency: Designing Effective State Programs for the Industrial Sector Industrial Energy Efficiency: Designing Effective State Programs for the Industrial...

  9. Industry

    E-Print Network [OSTI]

    Bernstein, Lenny

    2008-01-01T23:59:59.000Z

    iron and steel production. IEA Greenhouse Gas R&D Programme,tempera- ture range. IEA/Caddet, Sittard, The Netherlands.industry. Cheltenham, UK, IEA Greenhouse Gas R&D Programme,

  10. Industry

    E-Print Network [OSTI]

    Bernstein, Lenny

    2008-01-01T23:59:59.000Z

    process residual like bagasse are now available (Cornland etsugar in- dustry uses bagasse and the edible oils industrySection 7.4.7. ). The use of bagasse for energy is likely to

  11. Improvements to a Transport Model of Asphalt Binder Oxidation in Pavements: Pavement Temperature Modeling, Oxygen Diffusivity in Asphalt Binders and Mastics, and Pavement Air Void Characterization

    E-Print Network [OSTI]

    Han, Rongbin

    2012-07-16T23:59:59.000Z

    Although evidence is mounting that asphalt binder oxidizes in pavements, and that oxidation and subsequent hardening of asphalt binder has a profound effect on pavement durability, important implementation issues remain to be better understood...

  12. Power Politics: The Political Economy of Russia's Electricity Sector Liberalization

    E-Print Network [OSTI]

    Wengle, Susanne Alice

    2010-01-01T23:59:59.000Z

    Private Participation in the Electricity Sector World BankTelecommunications and Electricity Sectors." Governance 19,Power Struggle: Reforming the Electricity Industry." In The

  13. Asphalt Pavement Aging and Temperature Dependent Properties through a Functionally Graded Viscoelastic Model, Part-II: Applications

    E-Print Network [OSTI]

    Paulino, Glaucio H.

    Asphalt Pavement Aging and Temperature Dependent Properties through a Functionally Graded simulation of functionally graded viscoelastic properties in asphalt concrete pavements. The techniques properties. A full-depth asphalt concrete pavement has been simulated to demonstrate the applicability

  14. The curing of asphalt with rubber and its effect on the physical and chemical properties of asphalt-rubber binders

    E-Print Network [OSTI]

    Chun, Jay Sung

    1995-01-01T23:59:59.000Z

    10% TG-40 and 90% Exxon AC-5. 105 B-1 Molecular Size Distribution of Rubber in Asphalt 5% TG-40 and 95% Fina AC-10. . . 123 B-2 Molecular Size Distribution of Rubber in Asphalt 10% TG-40 and 90% Fina AC-10. . 124 xlv FIGURE B-3 Molecular Size.... 0 Frequency (rad/s) 10. 0 100. 0 Figure III-2: Effect of Frequency on Viscosity Measurements Fina AC-10 Tank Asphalt 2500 2000 0 a 1500 1000 o 0 0 0 0 o o 0 0 0 0 0 0 0 o 0 Fina AC-10 with 5% TG-40 mesh rubber Cured at 375 F and 500...

  15. asphalt emulsions: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Next Page Last Page Topic Index 21 Life Cycle Assessment of Reclaimed Asphalt Pavement Energy Storage, Conversion and Utilization...

  16. Characterization of Fatigue Cracking and Healing of Asphalt Mixtures

    E-Print Network [OSTI]

    Luo, Xue

    2012-07-16T23:59:59.000Z

    mixtures using an energy-based mechanistic approach. A controlled-strain repeated direct tension (RDT) test is selected to generate both fatigue cracking and permanent deformation in an asphalt mixture specimen. Fatigue cracking is separated from...

  17. Viscoelastic{Viscoplastic Damage Model for Asphalt Concrete

    E-Print Network [OSTI]

    Graham, Michael A.

    2010-10-12T23:59:59.000Z

    This thesis presents a continuum model for asphalt concrete incorporating non- linear viscoelasticity, viscoplasticity, mechanically-induced damage and moisture- induced damage. The Schapery single-integral viscoelastic model describes the nonlinear...

  18. A thermodynamic approach for compaction of asphaltic composites

    E-Print Network [OSTI]

    Koneru, Saradhi

    2009-05-15T23:59:59.000Z

    and Focus of Current Work . . . . . . . . . . . . . . 2 B. Outline of the Thesis . . . . . . . . . . . . . . . . . . . . . 3 C. Notations Used . . . . . . . . . . . . . . . . . . . . . . . . 4 II LITERATURE REVIEW... . . . . . . . . . . . . . . . . 8 b. Asphalt Binder . . . . . . . . . . . . . . . . . . . 8 C. Compaction Equipment . . . . . . . . . . . . . . . . . . . . 9 1. Field Compaction Equipment . . . . . . . . . . . . . . 9 a. Static Steel Wheel Rollers . . . . . . . . . . . . . 9 b...

  19. asphaltic pavements microsurfacing: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    service have been... Lau, Chee Keung 1991-01-01 14 A utility evaluation of nondestructive testing devices used on asphalt concrete pavements Texas A&M University - TxSpace...

  20. asphalt pavement cracking: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    service have been... Lau, Chee Keung 1991-01-01 16 A utility evaluation of nondestructive testing devices used on asphalt concrete pavements Texas A&M University - TxSpace...

  1. asphalt concrete pavement: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    this thesis. It included the following tasks: investigation of a testing and grading system for grading asphalt binder residues... Hoyt, Denise 2012-07-16 8 Full-Depth Pavement...

  2. asphalt pavement rap: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    service have been... Lau, Chee Keung 1991-01-01 14 A utility evaluation of nondestructive testing devices used on asphalt concrete pavements Texas A&M University - TxSpace...

  3. asphaltic concrete pavement: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    this thesis. It included the following tasks: investigation of a testing and grading system for grading asphalt binder residues... Hoyt, Denise 2012-07-16 8 Full-Depth Pavement...

  4. asphalt concrete pavements: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    this thesis. It included the following tasks: investigation of a testing and grading system for grading asphalt binder residues... Hoyt, Denise 2012-07-16 8 Full-Depth Pavement...

  5. asphaltic concrete pavements: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    this thesis. It included the following tasks: investigation of a testing and grading system for grading asphalt binder residues... Hoyt, Denise 2012-07-16 8 Full-Depth Pavement...

  6. asphalt pavements: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    service have been... Lau, Chee Keung 1991-01-01 14 A utility evaluation of nondestructive testing devices used on asphalt concrete pavements Texas A&M University - TxSpace...

  7. Measurements of moisture suction in hot mix asphalt mixes 

    E-Print Network [OSTI]

    Kassem, Emad Abdel-Rahman

    2006-10-30T23:59:59.000Z

    with different bond energies and exhibited different field performance in terms of resistance to moisture damage. The suction measurements in sand asphalt specimens were used to calculate the moisture diffusion coefficient. The results revealed that water...

  8. Moisture Diffusion in Asphalt Binders and Fine Aggregate Mixtures 

    E-Print Network [OSTI]

    Vasconcelos, Kamilla L.

    2011-08-08T23:59:59.000Z

    coefficient measurement of a wide variety of polymersolvent systems. For the asphalt-water system studied, the focus is on two techniques: (i) Fourier Transform Infrared (FTIR)-Attenuated Total Reflectance (ATR) spectrometry and (ii) Gravimetric Sorption...

  9. Imparting Electrical Conductivity into Asphalt Composites Using Graphite 

    E-Print Network [OSTI]

    Baranikumar, Aishwarya

    2013-07-09T23:59:59.000Z

    publications showed the potential of graphite in mitigating the sudden transition. The study presented herein investigates possibility of precisely controlling the electrical conductivity of asphalt concrete only by adding filler size graphite powder. Nine...

  10. asphalt concrete performance: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Robert L. 2014-01-01 23 Establishing material properties for thin asphalt concrete surfaces on granular bases Texas A&M University - TxSpace Summary: of MASTER OF SCIENCE...

  11. Use of VFDs on Asphalt Plant Induced Draft Fans

    E-Print Network [OSTI]

    Anderson, G. R.; Case, P. L.; Lowery, J.

    2005-01-01T23:59:59.000Z

    Studies of 10 asphalt plants in the Intermountain Region have identified average ID fan energy savings of 68% by controlling airflow using Variable Frequency Drives (VFDs) on the fan motors in place of damper control (inlet or outlet). Average...

  12. Fiber reinforcement of asphalt concrete using cow manure

    E-Print Network [OSTI]

    Bakar, Mohammed Abu

    1976-01-01T23:59:59.000Z

    . Specimens were made according to the Marshall Method of Mixture Design and tested for 1) Marshall Stability 2) Hveem Stability and 3) Hater Susceptibil- ity. Test results indicated that 4. 4 percent cow manure by volume of rhe total aggregate when used... Voids in Mineral Aggregate 11 LIST OF FIGURES Figures Page l. 2 l. 3 1. 4 1. 5 1. 6 Determination of Optimum Asphalt Content by the Marshall Method Determination of Optimum Asphalt Content by the Marshall Method Determination of Optimum...

  13. Characterization of road asphalt using Gel Permeation Chromatography

    E-Print Network [OSTI]

    Donaldson, Guy Randal

    1987-01-01T23:59:59.000Z

    inconsistent and inconsistent. Six were consistent, three were slightly inconsist nt, and three were inconsistent. To study the relationship between GPC and performance, samples from test pavements at three locations were obtained. Both original asphalts... Columns/Toluene/100 Nicroliters/ 7X 3 ' 2. Reproducibility of the Standard Asphalt in THF . ~ . . ~ . ~ . . . 500 and 50 Angstrom Columns/Toluene/100 Nicroliters/ 7X 19 3. 3. Differences in Refractive Index Detector Response. Exxon AC-10/Dumas Tank...

  14. Fatigue Resistance of Asphalt Mixtures Affected by Water Vapor Movement

    E-Print Network [OSTI]

    Tong, Yunwei

    2013-11-08T23:59:59.000Z

    aggregate contact due to dust particles on the aggregate surface. The rupture may occur because of the construction loads and operating traffic during construction, or could be environmentally induced by freeze-thaw cycling. Once a break in the film... design, environment and traffic, can be defined as progressive degradation of asphalt mixture material due to the presence of water. The occurrence of moisture damage in asphalt material is a rather complex phenomenon, which involves chemical, physical...

  15. Public Interest Energy Research (PIER) Program FINAL PROJECT REPORT California Energy Balance Update and Decomposition Analysis for the Industry and Building Sectors

    E-Print Network [OSTI]

    de la Rue du Can, Stephane

    2014-01-01T23:59:59.000Z

    of which: CHP ele generation Residential Nonspecified (OtherOther Services (CHP heat Fuel use) Residential End Use (non-Residential Nonspecified (Other Sector) NEW Office (CHP heat

  16. Energy Efficiency Opportunities in the Stone and Asphalt Industry

    E-Print Network [OSTI]

    Moray, S.; Throop, N.; Seryak, J.; Schmidt, C.; Fisher, C.; D'Antonio, M.

    2006-01-01T23:59:59.000Z

    transportation within and outside of the quarry is the most common method of stone transportation. In-plant, the largest use of diesel is from the haul trucks moving the shot-rock from the quarry to the primary crusher. Diesel fuel costs are significant and can... and consistent product gradation, cone crushers must be choke fed at all times. Portable Crushers. A typical quarry face will recede approximately 45 feet every year. This extra distance increases the work of the haul trucks that feed the primary crushers...

  17. Development of Bottom-up Representation of Industrial Energy Efficiency Technologies in Integrated Assessment Models for the Iron and Steel Sector

    SciTech Connect (OSTI)

    Xu, T.T.; Sathaye, J.; Galitsky, C.

    2010-09-30T23:59:59.000Z

    Adoption of efficient end-use technologies is one of the key measures for reducing greenhouse gas (GHG) emissions. With the working of energy programs and policies on carbon regulation, how to effectively analyze and manage the costs associated with GHG reductions become extremely important for the industry and policy makers around the world. Energy-climate (EC) models are often used for analyzing the costs of reducing GHG emissions (e.g., carbon emission) for various emission-reduction measures, because an accurate estimation of these costs is critical for identifying and choosing optimal emission reduction measures, and for developing related policy options to accelerate market adoption and technology implementation. However, accuracies of assessing of GHG-emission reduction costs by taking into account the adoption of energy efficiency technologies will depend on how well these end-use technologies are represented in integrated assessment models (IAM) and other energy-climate models. In this report, we first conduct brief overview on different representations of end-use technologies (mitigation measures) in various energy-climate models, followed by problem statements, and a description of the basic concepts of quantifying the cost of conserved energy including integrating non-regrets options. A non-regrets option is defined as a GHG reduction option that is cost effective, without considering their additional benefits related to reducing GHG emissions. Based upon these, we develop information on costs of mitigation measures and technological change. These serve as the basis for collating the data on energy savings and costs for their future use in integrated assessment models. In addition to descriptions of the iron and steel making processes, and the mitigation measures identified in this study, the report includes tabulated databases on costs of measure implementation, energy savings, carbon-emission reduction, and lifetimes. The cost curve data on mitigation measures are available over time, which allows an estimation of technological change over a decade-long historical period. In particular, the report will describe new treatment of technological change in energy-climate modeling for this industry sector, i.e., assessing the changes in costs and energy-savings potentials via comparing 1994 and 2002 conservation supply curves. In this study, we compared the same set of mitigation measures for both 1994 and 2002 -- no additional mitigation measure for year 2002 was included due to unavailability of such data. Therefore, the estimated potentials in total energy savings and carbon reduction would most likely be more conservative for year 2002 in this study. Based upon the cost curves, the rate of change in the savings potential at a given cost can be evaluated and be used to estimate future rates of change that can be the input for energy-climate models. Through characterizing energy-efficiency technology costs and improvement potentials, we have developed and presented energy cost curves for energy efficiency measures applicable to the U.S. iron and steel industry for the years 1994 and 2002. The cost curves can change significantly under various scenarios: the baseline year, discount rate, energy intensity, production, industry structure (e.g., integrated versus secondary steel making and number of plants), efficiency (or mitigation) measures, share of iron and steel production to which the individual measures can be applied, and inclusion of other non-energy benefits. Inclusion of other non-energy benefits from implementing mitigation measures can reduce the costs of conserved energy significantly. In addition, costs of conserved energy (CCE) for individual mitigation measures increase with the increases in discount rates, resulting in a general increase in total cost of mitigation measures for implementation and operation with a higher discount rate. In 1994, integrated steel mills in the U.S. produced 55.

  18. Industrial Sector Energy Conservation Programs in the People's Republic of China during the Seventh Five-Year Plan (1986-1990)

    E-Print Network [OSTI]

    Zhiping, L.

    2010-01-01T23:59:59.000Z

    Plans Organization and Implementation of Energy ConservationIndustrial Energy Conservation Investment Funding 3.Case Studies of Energy Conservation Investments by Industry

  19. The Role of the Sellafield Ltd Centres of Expertise in Engaging with the Science, Environment and Technology Supply Chain and University Sector to Support Site Operations and Decommissioning in the UK Nuclear Industry - 13018

    SciTech Connect (OSTI)

    Butcher, Ed [Uranium and Reactive Metals Centre of Expertise Lead, Technical Directorate, Sellafield Ltd, Sellafield, Seascale, Cumbria CA20 1PG (United Kingdom)] [Uranium and Reactive Metals Centre of Expertise Lead, Technical Directorate, Sellafield Ltd, Sellafield, Seascale, Cumbria CA20 1PG (United Kingdom); Connor, Donna [Technical Capability Manager, Technical Directorate, Sellafield Ltd, Sellafield, Seascale, Cumbria CA20 1PG (United Kingdom)] [Technical Capability Manager, Technical Directorate, Sellafield Ltd, Sellafield, Seascale, Cumbria CA20 1PG (United Kingdom); Keighley, Debbie [Head of Profession, Technical Directorate, Sellafield Ltd, Sellafield, Seascale, Cumbria CA20 1PG (United Kingdom)] [Head of Profession, Technical Directorate, Sellafield Ltd, Sellafield, Seascale, Cumbria CA20 1PG (United Kingdom)

    2013-07-01T23:59:59.000Z

    The development and maintenance of the broad range of the highly technical skills required for safe and successful management of nuclear sites is of vital importance during routine operations, decommissioning and waste treatment activities.. In order to maintain a core team of technical experts, across all of the disciplines required for these tasks, the approach which has been taken by the Sellafield Ltd has been the formation of twenty five Centres of Expertise (CoE), each covering key aspects of the technical skills required for nuclear site operations. Links with the Specialist University Departments: The CoE leads are also responsible for establishing formal links with university departments with specialist skills and facilities relevant to their CoE areas. The objective of these links is to allow these very specialist capabilities within the university sector to be more effectively utilized by the nuclear industry, which benefits both sectors. In addition to the utilization of specialist skills, the university links are providing an important introduction to the nuclear industry for students and researchers. This is designed to develop the pipeline of potential staff, who will be required in the future by both the academic and industrial sectors. (authors)

  20. Investigation of Conditions for Moisture Damage in Asphalt Concrete and Appropriate Laboratory Test Methods

    E-Print Network [OSTI]

    Lu, Qing

    2005-01-01T23:59:59.000Z

    of Asphalt Concrete-Physical Testing. ” Final Report, #930-of Asphalt Concrete: Chemical Testing. ” Alabama Highwayconcrete mixes, it is preferred to use a mix that would have good moisture resistance under laboratory testing

  1. Investigation of Conditions for Moisture Damage in Asphalt Concrete and Appropriate Laboratory Test Methods

    E-Print Network [OSTI]

    Harvey, John T; Lu, Qing

    2005-01-01T23:59:59.000Z

    of Asphalt Concrete-Physical Testing. ” Final Report no.of Asphalt Concrete: Chemical Testing. ” Alabama Highwayconcrete mixes, it is preferable to use a mix that would have good moisture resistance under laboratory testing

  2. A Coupled Micromechanical Model of Moisture-Induced Damage in Asphalt Mixtures: Formulation and Applications 

    E-Print Network [OSTI]

    Caro Spinel, Silvia

    2011-02-22T23:59:59.000Z

    The deleterious effect of moisture on the structural integrity of asphalt mixtures has been recognized as one of the main causes of early deterioration of asphalt pavements. This phenomenon, usually referred to as moisture damage, is defined...

  3. Experimental Study on Geocell-Reinforced Recycled Asphalt Pavement (RAP) Bases under Static and Cyclic Loading

    E-Print Network [OSTI]

    Thakur, Jitendra Kumar

    2011-01-13T23:59:59.000Z

    Recycled Asphalt Pavement (RAP) is a removed and reprocessed pavement material containing asphalt and aggregates which can be used as a base course material for pavement applications. Geocells are a three-dimensional interconnected honeycomb type...

  4. Asphalt compositions containing spurted polyolefin fibers with improved dispersibility in hydrocarbons

    SciTech Connect (OSTI)

    Jabloner, H.

    1987-07-07T23:59:59.000Z

    A cutback asphalt composition is described comprising asphalt and a hydrocarbon solvent. The improvement composition comprises a water-dispersible spurted polyolefin pulp having precipitated a natural rubber or synthetic elastomer that is swellable in hydrocarbon solvents.

  5. E-Print Network 3.0 - asphalt mix design Sample Search Results

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and Environmental Engineering, Arizona State University Collection: Engineering 35 Bi Oil i A h ltBio-Oil in Asphalt ApplicationsApplications Summary: tons of hot mix asphalt...

  6. Evaluation of the filler effects on fatique cracking and permanent deformation of asphalt concrete mixtures 

    E-Print Network [OSTI]

    Izzo, Richard P

    1997-01-01T23:59:59.000Z

    The addition of hydrated lime to asphalt has shown to be beneficial with an improvement in the Theological properties of the binder, as well as resistance to permanent deformation (rutting) and fatigue cracking of asphalt concrete mixtures...

  7. Evaluation of the filler effects on fatique cracking and permanent deformation of asphalt concrete mixtures

    E-Print Network [OSTI]

    Izzo, Richard P

    1997-01-01T23:59:59.000Z

    The addition of hydrated lime to asphalt has shown to be beneficial with an improvement in the Theological properties of the binder, as well as resistance to permanent deformation (rutting) and fatigue cracking of asphalt concrete mixtures...

  8. Public Interest Energy Research (PIER) Program FINAL PROJECT REPORT California Energy Balance Update and Decomposition Analysis for the Industry and Building Sectors

    E-Print Network [OSTI]

    de la Rue du Can, Stephane

    2014-01-01T23:59:59.000Z

    Losses CHP, Commercial Power CHP, Electric Power CHP, Industrial Power Electric Generators, Utilities

  9. Development of asphalts and pavements using recycled tire rubber. Phase 1: technical feasibility. Final report

    SciTech Connect (OSTI)

    Bullin, J.A.; Davison, R.R.; Glover, C.J. [and others

    1998-01-01T23:59:59.000Z

    This report documents the technical progress made on the development of asphalts and pavements using recycled tire rubber.

  10. A study of the mixing viscosity of asphalt in hot-mix production

    E-Print Network [OSTI]

    Khan, Md. Musharraf Hossain

    1961-01-01T23:59:59.000Z

    Gravity and Absorption of Aggregates. 36 Sieve Analysis of Combined Aggregates 37 Centrifuge Kerosene Equivalent Test Data for Estimated Optimum Asphalt Content . 38 Test Data on Molded Specimens for Optimum Asphalt Content 39 XIII . Test Data... there is available to be filled with asphalt. The Centrifuge Kerosene Equivalent (CKE) Test was performed to 11 determine the estimated optimum asphalt content as a percentage of the 10 The American Association of State Highway Officials, "Standard...

  11. Climate VISION: Private Sector Initiatives: Electric Power

    Office of Scientific and Technical Information (OSTI)

    Letters of IntentAgreements The electric power sector participates in the Climate VISION program through the Electric Power Industry Climate Initiative (EPICI) and its Power...

  12. Climate VISION: Private Sector Initiatives: Cement

    Office of Scientific and Technical Information (OSTI)

    various sources describing the energy consumption of the industrial sector and the carbon emissions in particular. Below is an estimate of the emissions expressed in million...

  13. Climate VISION: Private Sector Initiatives: Automobile Manufacturers...

    Office of Scientific and Technical Information (OSTI)

    various sources describing the energy consumption of the industrial sector and the carbon emissions in particular. Below is an estimate of the million metric tons of carbon...

  14. Asphalt Roofing Shingles Into Energy Project Summary Report

    SciTech Connect (OSTI)

    Jameson, Rex, PE

    2008-04-28T23:59:59.000Z

    Based on a widely cited September, 1999 report by the Vermont Agency of Natural Resources, nearly 11 million tons of asphalt roofing shingle wastes are produced in the United States each year. Recent data suggests that the total is made up of about 9.4 million tons from roofing tear-offs and about 1.6 million tons from manufacturing scrap. Developing beneficial uses for these materials would conserve natural resources, promote protection of the environment and strengthen the economy. This project explored the feasibility of using chipped asphalt shingle materials in cement manufacturing kilns and circulating fluidized bed (CFB) boilers. A method of enhancing the value of chipped shingle materials for use as fuel by removing certain fractions for use as substitute raw materials for the manufacture of new shingles was also explored. Procedures were developed to prevent asbestos containing materials from being processed at the chipping facilities, and the frequency of the occurrence of asbestos in residential roofing tear-off materials was evaluated. The economic feasibility of each potential use was evaluated based on experience gained during the project and on a review of the well established use of shingle materials in hot mix asphalt. This project demonstrated that chipped asphalt shingle materials can be suitable for use as fuel in circulating fluidized boilers and cement kilns. More experience would be necessary to determine the full benefits that could be derived and to discover long term effects, but no technical barriers to full scale commercial use of chipped asphalt shingle materials in these applications were discovered. While the technical feasibility of various options was demonstrated, only the use of asphalt shingle materials in hot mix asphalt applications is currently viable economically.

  15. Recycling of plastic and rubber tire waste in asphalt pavements

    SciTech Connect (OSTI)

    Morrison, G.R.; Lee, N.K.; Hesp, S.A.M. [Queen`s Univ., Kingston, Ontario (Canada). Dept. of Chemistry

    1994-12-31T23:59:59.000Z

    This paper discusses some important issues related to the use of recycled thermoplastics and rubber tire waste in asphalt binders for hot-mix pavements. Both high temperature rheological and low temperature fracture studies are presented on recycled polyethylene, devulcanized and crumb rubber-modified asphalt binders. The results are compared to unmodified and commercially available modified binders. This research is especially timely in light of the US Intermodal Surface Transportation Efficiency Act of 1991, Section 1038 which, starting in 1995, will force state and local governments to use significant amounts of recycled rubber tire or plastic waste in federally funded highway projects. High temperature rheological measurements of the loss modulus, loss tangent and complex modulus show a significant improvement when only small quantities of crumb rubber, devulcanized crumb rubber or waste polyethylene are added to the asphalt binders. The low temperature fracture performance of the modified asphalts is greatly influenced by the interfacial strength between the dispersed and continuous phase. The fracture toughness increases dramatically, only when low molecular weight polymers are grafted in-situ onto the rubber and polymer dispersed phases in order to strength the interface. This points to a crack-pinning mechanism as being responsible for the dramatic increase in fracture toughness that is observed in this work. Single phase, devulcanized crumb rubber-asphalt systems perform quite poorly at low temperatures.

  16. Use of recycled chunk rubber asphalt concrete (CRAC) on low volume roads and use of recycled crumb rubber modifier in asphalt pavements. Final report, June 1993-June 1995

    SciTech Connect (OSTI)

    Hossain, M.; Funk, L.P.; Sadeq, M.A.; Marucci, G.

    1995-06-01T23:59:59.000Z

    The major objective of this project was to formulate a Chunk Rubber Asphalt Concrete (CRAC) mix for use on low volume roads. CRAC is a rubber modified asphalt concrete product produced by the `dry process` where rubber chunks of 1/2 inch size are used as aggregate in a cold mix with a type C fly ash. The second objective of this project was to develop guidelines concerning the use of rubber modified asphalt concrete hot mix to include: (1) Design methods for use of asphalt-rubber mix for new construction and overlay, (2) Mix design method for asphalt-rubber, and (3) Test method for determining the amount of rubber in an asphalt-rubber concrete for quality control purposes.

  17. A study of the effects of limestone rock asphalt screenings on the structural properties of hot-mix asphaltic concrete made with siliceous materials 

    E-Print Network [OSTI]

    Albritton, Oscar Willard

    1958-01-01T23:59:59.000Z

    LiSRagy pptt8pp py IEXAa A STUDY OF THE EFFECTS OF LIMESTONE ROCK ASPHALT SCREENINGS ON THE STRUCTURAL PROPERTIES OF HOT-MIX ASPHALTIC CONCRETE MADE WITH SILICEOUS MATERIALS A Thesis By OSCAR WILLARD. AQBRITTON Submitted to the Graduate... ON THE STRUCTURAL PROPERTIES OF HOT-MIX ASPHALTIC CONCRETE MADE WITH SILICEOUS MATERIALS A Thesis By OSCAR WILLARD ALBRITTON Approved as to Style and Content by: Chairman of Committee ead of Departme t August 1958 ACKNOWLEDGMENTS Acknowledgment is due...

  18. Automated titration method for use on blended asphalts

    DOE Patents [OSTI]

    Pauli, Adam T. (Cheyenne, WY); Robertson, Raymond E. (Laramie, WY); Branthaver, Jan F. (Chatham, IL); Schabron, John F. (Laramie, WY)

    2012-08-07T23:59:59.000Z

    A system for determining parameters and compatibility of a substance such as an asphalt or other petroleum substance uses titration to highly accurately determine one or more flocculation occurrences and is especially applicable to the determination or use of Heithaus parameters and optimal mixing of various asphalt stocks. In a preferred embodiment, automated titration in an oxygen gas exclusive system and further using spectrophotometric analysis (2-8) of solution turbidity is presented. A reversible titration technique enabling in-situ titration measurement of various solution concentrations is also presented.

  19. Bottom-up Representation of Industrial Energy Efficiency Technologies in Integrated Assessment Models for the U.S. Pulp and Paper Sector

    E-Print Network [OSTI]

    Xu, Tengfang

    2014-01-01T23:59:59.000Z

    Sixth Annual Industrial Energy Technology Conference, VolumeBNL). 2001. The Energy Technology Systems AnalysisKramer Environmental Energy Technologies Division July 2012

  20. Industrial Sector Energy Conservation Programs in the People's Republic of China during the Seventh Five-Year Plan (1986-1990)

    E-Print Network [OSTI]

    Zhiping, L.

    2010-01-01T23:59:59.000Z

    of crude oil and oil products; (iii) retrofitting existingof petroleum products, limit proliferation of oil usingand product mix in energy-intensive industries; converting oil-

  1. A Methodology of Quantifying Precipitation Exposure for Wet-Weather Collisions and Evaluating Effectiveness of Open-Grade Asphalt Concrete as a Countermeasure

    E-Print Network [OSTI]

    Chan, Ching-Yao; Jin, Eui-Jae; Oh, Soon Mi; Ragland, David R

    2010-01-01T23:59:59.000Z

    Open-graded Asphaltic Concrete Friction Courses in Arizona.for Open-Graded Asphalt Concrete (OGAC) Wearing Courses.of Open-Grade Asphalt Concrete as a Countermeasure Ching-Yao

  2. asphalt technology development: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    asphalt technology development First Page Previous Page 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Next Page Last Page Topic Index 1 Development and...

  3. asphalt based materials: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    asphalt based materials First Page Previous Page 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Next Page Last Page Topic Index 1 Establishing material...

  4. Controlling Thermal Properties of Asphalt Concrete and its Multifunctional Applications

    E-Print Network [OSTI]

    Shi, Xijun

    2014-08-10T23:59:59.000Z

    of the thermally modified asphalt mixtures on the surface temperature of pavements and bridges, a series of heat transfer analysis were conducted using the finite difference heat transfer model. In addition, a case study of a building using EPP modified cement...

  5. Measurements of moisture suction in hot mix asphalt mixes

    E-Print Network [OSTI]

    Kassem, Emad Abdel-Rahman

    2006-10-30T23:59:59.000Z

    The presence of moisture in hot mix asphalt (HMA) causes loss of strength and durability of the mix, which is referred to as moisture damage. This study deals with the development of experimental methods for measuring total suction in HMA, which can...

  6. asphalt construction premature: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    asphalt construction premature First Page Previous Page 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Next Page Last Page Topic Index 1 Moisture Diffusion in...

  7. Public Interest Energy Research (PIER) Program FINAL PROJECT REPORT California Energy Balance Update and Decomposition Analysis for the Industry and Building Sectors

    E-Print Network [OSTI]

    de la Rue du Can, Stephane

    2014-01-01T23:59:59.000Z

    solid waste from landfill gas in electricity source data,and Wood Derived Fuels Landfill Gas GWh Other Biogas MSWFuels Industrial CHP Landfill Gas Other Biogas NAICS 22 CHP

  8. Summary of Construction Activities and Results from Six Initial Accelerated Pavement Tests Conducted on Asphalt Concrete Pavement Section for Modified-Binder Overlay

    E-Print Network [OSTI]

    Bejarano, Manuel O.; Morton, Bruce S.; Scheffy, Clark

    2005-01-01T23:59:59.000Z

    Testing on the Asphalt Concrete FWD testing was conducted onin asphalt concrete modulus after HVS testing for Sectionsconcrete pavements under accelerated pavement testing. This

  9. The use of sulfer modified bottom ash (SMBA) as an aggregate in asphaltic mixtures

    E-Print Network [OSTI]

    Chimakurthy, Harshavardhan

    1998-01-01T23:59:59.000Z

    , bottom ash is lighter in weight and generally much cheaper than conventional quality aggregates such as limestone, sand and gravel. This research was designed to up-grade the load-bearing charactcnstics of bottom ash and maximize its usc m asphaltic... and gravel. According to a study done by Hafizuddin Ahmad in 1974, sulfur was used extensively in sand-asphalt sulfur to upgrade marginal aggregates for use in asphaltic mixtures, was developed at Texas Transportation Institute (TT1) (JO). TTI's work...

  10. Tertiary nitrogen heterocyclic material to reduce moisture-induced damage in asphalt-aggregate mixtures

    DOE Patents [OSTI]

    Plancher, Henry (Laramie, WY); Petersen, Joseph C. (Laramie, WY)

    1982-01-01T23:59:59.000Z

    Asphalt-aggregate roads crack when subjected to freezing and thawing cycles. Herein, the useful life of asphalts are substantially improved by a minor amount of a moisture damage inhibiting agent selected from compounds having a pyridine moiety, including acid salts of such compounds. A shale oil fraction may serve as the source of the improving agent and may simply be blended with conventional petroleum asphalts.

  11. The use of HPGPC for determination of MWD of asphalt cement - A spectrophotometric vs. gravimetric finish

    SciTech Connect (OSTI)

    Bishara, S.W.; McReynolds, R.L. (Kansas Dept. of Transportation, Topeka (United States))

    1990-07-01T23:59:59.000Z

    A comparison between spectrophotometric and gravimetric methods to study MWD of asphalt is presented. Spectrophotometry suffers from not detecting saturated compounds, as well as from variation of molar absorptivity during analysis. To address these shortcoming, the whole asphalt sample is fractionated, and the relative molar absorptivity determined for each fraction. Using another sample weight of the whole asphalt, the saturates are separated, and injected to get their MWD using refractive index detection. This information, when used to mathematically treat the whole asphalt distribution data, can correct the latter to include saturates as well, but can only partially account for continuous variation of the molar absorptivity.

  12. NOAA Helps the Construction Sector Build for a Changing Climate The construction industry is comprised of a wide range of business involved in engineering standards,

    E-Print Network [OSTI]

    million, and energy cost savings of 586,000 megawatt hours. Climate Information Reduces Construction Costs and Energy Consumption NOAA provides airfreezing data to the home building industry, which in annual building cost savings of $330 million and energy cost savings of 586,000 megawatthours. #12

  13. Experimental Study on Geocell-Reinforced Flexible Pavements with Recycled Asphalt Pavement (RAP) Bases under Cyclic Loading

    E-Print Network [OSTI]

    Acharya, B. S.

    2011-12-31T23:59:59.000Z

    ABSTRACT The reprocessed old hot mix asphalt (HMA) concrete also called "Recycled Asphalt Pavement (RAP)", if used to build new roads or to maintain existing roads, would have several benefits, such as preservation of natural resources for future...

  14. Asphalt Pavement Aging and Temperature Dependent Properties through a Functionally Graded Viscoelastic Model, Part-I: Development,

    E-Print Network [OSTI]

    Paulino, Glaucio H.

    Asphalt Pavement Aging and Temperature Dependent Properties through a Functionally Graded simulations, correspondence principle, finite-element method Abstract. Asphalt concrete pavements to climatic conditions are the major cause of such graded non-homogeneity. Current pavement analysis

  15. Microstructural Characterization of the Chemo-mechanical Behavior of Asphalt in Terms of Aging and Fatigue Performance Properties

    E-Print Network [OSTI]

    Allen, Robert Grover

    2013-03-27T23:59:59.000Z

    The study of asphalt chemo-mechanics requires a basic understanding of the physical properties and chemical composition of asphalt and how these properties are linked to changes in performance induced by chemical modifications. This work uniquely...

  16. Integrated coke, asphalt and jet fuel production process and apparatus

    DOE Patents [OSTI]

    Shang, Jer Y. (McLean, VA)

    1991-01-01T23:59:59.000Z

    A process and apparatus for the production of coke, asphalt and jet fuel m a feed of fossil fuels containing volatile carbon compounds therein is disclosed. The process includes the steps of pyrolyzing the feed in an entrained bed pyrolyzing means, separating the volatile pyrolysis products from the solid pyrolysis products removing at least one coke from the solid pyrolysis products, fractionating the volatile pyrolysis products to produce an overhead stream and a bottom stream which is useful as asphalt for road pavement, condensing the overhead stream to produce a condensed liquid fraction and a noncondensable, gaseous fraction, and removing water from the condensed liquid fraction to produce a jet fuel-containing product. The disclosed apparatus is useful for practicing the foregoing process. the process provides a useful method of mass producing and jet fuels from materials such as coal, oil shale and tar sands.

  17. Microstructural Characterization of Material Properties and Damage in Asphalt Composites 

    E-Print Network [OSTI]

    Mohammad Khorasani, Sara

    2013-05-03T23:59:59.000Z

    by NPRP grant # 08-310-2-110 from the Qatar National Research Fund (a member of Qatar Foundation). The statements made herein are solely the responsibility of the authors. vi TABLE OF CONTENTS Page ABSTRACT... ........................................................................................................................ 17 3D Experimental Investigation of the Microstructure of Cement Pastes Using Synchrotron X-Ray Microtomography (?CT) .......................................................... 18 Dynamic Modulus Simulation of the Asphalt Concrete Using the X...

  18. Evaluation of Rexene polymers in hot mixed asphalt concrete

    E-Print Network [OSTI]

    Rodriguez, Mary Anne Reese

    1991-01-01T23:59:59.000Z

    -- polyethylene, polypropylene, ethylene-vinyl acetate (EVA) and ethylene-propylene rubbers -- show increased stability and stiffness modulus, increased resistance to permanent deformation and lower temperature susceptibility. Carpenter and VanDam (14... five asphalt additives: block copolymer rubber, SBR latex, EVA, polyethylene and carbon black. Mixture stability, stiffness, tensile strength and resistance to fatigue, thermal cracking, permanent deformation and moisture damage were tested. Three...

  19. A novel method of bitumen extraction from asphalt pavement

    SciTech Connect (OSTI)

    Houser, T.J. (Western Michigan Univ., Kalamazoo (United States))

    1990-07-01T23:59:59.000Z

    A new method of extracting bitumen from asphalt pavement mixtures has been developed which does not require chlorinated or aromatic compounds for solvents. The preferred solvent is cyclohexane (although cyclopentane may be used) at high temperatures and pressures. The new method requires equipment that is less costly than the centrifuge method currently used and takes less time than extractions with Bioact but more time than when chlorocompounds are used.

  20. INTRODUCTION The increase in energy costs has led to a significant rise in the cost of mixtures containing asphalt cement. This resulted

    E-Print Network [OSTI]

    Harms, Kyle E.

    containing asphalt cement. This resulted in a need to search for alternatives that reduce the cost of those mixed with low percentages (1 percent below standard HMA mixtures) of paving grade asphalt cement and lower percentages of asphalt cement binder and easier compaction efforts. Asphalt treated mixtures can

  1. Effect of pavement temperature on the macrotexture of a semidense asphalt surface

    E-Print Network [OSTI]

    Boyer, Edmond

    Effect of pavement temperature on the macrotexture of a semidense asphalt surface J. Luong, M the pavement temperature could change the texture surface of the pavement. The aim of this work is to analyze the influence of the surface temperature on the macrotexture of a semidense asphalt pavement located in an urban

  2. Dynamic Effects on Moisture Transport in Asphalt Concrete M. Emin Kutay1

    E-Print Network [OSTI]

    Aydilek, Ahmet

    Dynamic Effects on Moisture Transport in Asphalt Concrete M. Emin Kutay1 and Ahmet H. Aydilek2 2007 133:7 406 CE Database subject headings: Moisture; Asphalt concrete; Dynamics; Hydraulic and Magdalena 2002 ; however, limited research has been conducted in modeling dynamic flow in porous geomedia

  3. RESEARCH REPORT 987-9 ASPHALT OVERLAY DESIGN METHODS FOR RIGID

    E-Print Network [OSTI]

    Texas at Austin, University of

    by using a fractional factorial design. An analysis of variance (ANOVA) was performed to identifyRESEARCH REPORT 987-9 ASPHALT OVERLAY DESIGN METHODS FOR RIGID PAVEMENTS CONSIDERING RUTTING's Catalog No. 5. Report Date October 1998 4. Title and Subtitle ASPHALT OVERLAY DESIGN METHODS FOR RIGID

  4. Industrial sector energy conservation programs in the People`s Republic of China during the seventh five-year plan (1986--1990)

    SciTech Connect (OSTI)

    Liu Zhiping [State Planning Commission, Beijing (China). Energy Research Inst.; Sinton, J.E.; Yang Fuqiang; Levine, M.D.; Ting, M.K. [Lawrence Berkeley Lab., CA (United States)

    1994-09-01T23:59:59.000Z

    The impetus at the national level to invest in energy conservation is quite strong and has long been reflected not only in official pronouncements, but also in the investments and organizational activities of the Chinese government. In the early 1980s the central government began a program of direct investments in industrial energy conservation that continues to the present. In addition, concurrently established governmental and quasi-governmental agencies have pursued conservation through administrative and educational measures. In Section 2 of this paper the authors outline the policies and institutions that supported China`s program of energy conservation investments in the Sixth and Seventh Five-Year Plans (FYPs) (1981--1985 and 1986--1990). In Section 3 they describe examples of the types of conservation projects pursued in four industrial subsectors: ferrous metals manufacturing; non-ferrous metals mining and manufacturing; chemicals manufacturing; and building materials manufacturing. Section 4 presents a simple methodology for comparing the costs of energy conservation to those of energy supply. Further discussion points out the applicability and limitations of this methodology to State Planning Commission published statistical material on the overall results of energy conservation investments. Though problematic, such analysis indicates that energy conservation investments were probably substantially cheaper than investments in equivalent energy supply would have been. They end with a discussion of some of the difficulties encountered in carrying out the conservation investment programs.

  5. Industrial policy and the Indian electronics industry

    E-Print Network [OSTI]

    Love, Robert (Robert Eric)

    2008-01-01T23:59:59.000Z

    Recently, production within India's Electronics sector amounted to a low $12 billion when compared to the global output of $1400 billion. The slow growth in the local industry is often judged to be the result of late ...

  6. Characterization of asphalt cements modified with crumbed rubber from discarded tires. Final report

    SciTech Connect (OSTI)

    Daly, W.H.; Negulescu, I.I.

    1994-11-01T23:59:59.000Z

    The potential legislative requirement for incorporation of scrap rubber into asphalt blends mandated a thorough evaluation of the influence of scrap rubber additives on the physical properties and aging characteristics of rubber/asphalt blends. Blends with up to 20 percent ground vulcanized rubber (both crumb and 200 mesh powder particles) from recycled tires were prepared with asphalt cements of various grades (AC5 - AC30) and evaluated using DMA. Blends produced from powdered rubber particles exhibited Newtonian behavior at high temperatures; similar behavior was not observed with crumb rubber blends. The mechanical properties of asphalt-rubber blends depend upon the concentration of rubber additives, the particle dimensions, and the chemical composition of the asphalt.

  7. Climate VISION: Private Sector Initiatives: Mining: GHG Information

    Office of Scientific and Technical Information (OSTI)

    various sources describing the energy consumption of the industrial sector and the carbon emissions in particular. Below is an estimate of the million metric tons of carbon...

  8. A study of the effects of limestone rock asphalt screenings on the structural properties of hot-mix asphaltic concrete made with siliceous materials

    E-Print Network [OSTI]

    Albritton, Oscar Willard

    1958-01-01T23:59:59.000Z

    Society for Testing Materials, Phila. , Pa. 15 PROCEDURE To limit the wide variations of aggregate grading, specifica- tions of the Texas Highway Department for a Type "D" Hot-Mix, Hot- Laid, Asphaltic Concrete were used as a guide in the design... Standards on Mineral Aggregates, Concrete, and Nonbituminous Highway Materials, American Society for Testing Materials, Phila, , Pa. Benson, Fred J, and Bh. Subbaraju, "Specific Gravity of Aggregates in Asphaltic Paving Mixtures, " Texas Engineering...

  9. Industry Supply Chain Development (Ohio)

    Broader source: Energy.gov [DOE]

    Supply Chain Development programs are focused on targeted industries that have significant growth opportunities for Ohio's existing manufacturing sector from emerging energy resources and...

  10. Research Projects in Industrial Technology.

    SciTech Connect (OSTI)

    United States. Bonneville Power Administration. Industrial Technology Section.

    1990-06-01T23:59:59.000Z

    The purpose of this booklet is to briefly describe ongoing and completed projects being carried out by Bonneville Power Administration's (BPA) Industrial Technology Section. In the Pacific Northwest, the industrial sector is the largest of the four consuming sectors. It accounted for thirty-nine percent of the total firm demand in the region in 1987. It is not easy to asses the conservation potential in the industrial sector. Recognizing this, the Northwest Power Planning Council established an objective to gain information on the size, cost, and availability of the conservation resource in the industrial sector, as well as other sectors, in its 1986 Power Plan. Specifically, the Council recommended that BPA operate a research and development program in conjunction with industry to determine the potential costs and savings from efficiency improvements in industrial processes which apply to a wide array of industrial firms.'' The section, composed of multidisciplinary engineers, provides technical support to the Industrial Programs Branch by designing and carrying out research relating to energy conservation in the industrial sector. The projects contained in this booklet are arranged by sector --industrial, utility, and agricultural -- and, within each sector, chronologically from ongoing to completed, with those projects completed most recently falling first. For each project the following information is given: its objective approach, key findings, cost, and contact person. Completed projects also include the date of completion, a report title, and report number.

  11. Innovative New Industrial Technologies: An Industry/DOE Joint Endeavor

    E-Print Network [OSTI]

    Gross, T. J.

    The Department of Energy’s Office of Industrial Programs supports research and development leading to improved energy efficiency and greater overall productivity in the industrial sector. Its basic strategy is a program of cost-shared R...

  12. High temperature performance of scrap tire rubber modified asphalt concrete

    SciTech Connect (OSTI)

    Coomarasamy, A. [Ministry of Transportation, Downsview, Ontario (Canada); Manolis, S.; Hesp, S. [Queen`s Univ., Kingston, Ontario (Canada)

    1996-12-31T23:59:59.000Z

    Wheel track rutting tests on mixes modified with 30 mesh, 80 mesh, and very fine colloidal crumb rubber particles show that a very significant improvement in performance occurs with a reduction in the rubber particle size. The SHRP binder test for rutting, which was originally developed for homogeneous systems only, does not predict the performance improvement for smaller rubber particles. If these new scrap rubber binder systems are to be used in pavements then rutting tests on the asphalt-aggregate mixture should be conducted in order to accurately predict high temperature performance.

  13. Canada's Voluntary Industrial Energy Conservation Program

    E-Print Network [OSTI]

    Wolf, C. A., Jr.

    1980-01-01T23:59:59.000Z

    Industrial Energy Conservation in Canada is organized and promoted through a voluntary program that is administered by industry. Industry is divided into fifteen sectors, each of which is represented by a Voluntary Task Force. Information exchange...

  14. Influence of fundamental material properties and air void structure on moisture damage of asphalt mixes 

    E-Print Network [OSTI]

    Arambula Mercado, Edith

    2009-05-15T23:59:59.000Z

    parameters were obtained using mechanical tests and surface energy measurements. The microstructure of asphalt mixes prepared in the laboratory having different air void structures was captured using X-ray CT, and image analysis techniques were used...

  15. Evaluation of healing in asphalt binders using dynamic shear rheometer and molecular modeling techniques 

    E-Print Network [OSTI]

    Bommavaram, Ramamohan Reddy

    2009-05-15T23:59:59.000Z

    A self-healing material has the inherent ability to partially reverse damage such as crack formation that might have occurred during its service. Significant evidence exists in the literature to indicate that asphalt binder is a self...

  16. A Continuum Coupled Moisture-mechanical Constitutive Model for Asphalt Concrete

    E-Print Network [OSTI]

    Shakiba, Maryam

    2013-12-09T23:59:59.000Z

    procedure and give insight into the various damage inducing mechanisms in asphalt concrete. In this dissertation, thermo-hygro-mechanical constitutive relationships are developed based on the principle of virtual power and laws of thermodynamics in order...

  17. Chip Seals for Asphalt Concrete Pavements: A Proposed Emulsion Residue Specification and Existing Pavement Texture Evaluation

    E-Print Network [OSTI]

    Hoyt, Denise

    2012-07-16T23:59:59.000Z

    Chip seals are a pavement surface treatment used for maintaining asphalt concrete pavements. National Cooperative Highway Research Program (NCHRP) Project 14-17 was performed to produce a national Chip Seal Manual which would consolidate the best...

  18. Development of superior asphalt recycling agency: Phase 1, Technical feasibility. Technical progress report

    SciTech Connect (OSTI)

    Bullin, J.A.; Glover, C.J.; Davison, R.R.; Lin, Moon-Sun; Chaffin, J.; Liu, Meng; Eckhardt, C.

    1996-04-01T23:59:59.000Z

    About every 12 years, asphalt roads must be reworked, and this is usually done by placing thick layers (hot-mix overlays) of new material on top of failed material, resulting in considerable waste of material and use of new asphalt binder. A good recycling agent is needed, not only to reduce the viscosity of the aged material but also to restore compatibility. Objective is to establish the technical feasibility (Phase I) of determining the specifications and operating parameters for producing high quality recycling agents which will allow most/all the old asphalt-based road material to be recycled. It is expected that supercritical fractionation can be used. The advanced road aging simulation procedure will be used to study aging of blends of old asphalt and recycling agents.

  19. A program to design asphalt concrete overlays to mitigate reflection cracking

    E-Print Network [OSTI]

    Satyanarayana Rao, Sindhu

    2002-01-01T23:59:59.000Z

    of the research are to understand the occurrence and behavior of reflection cracking and for devising ways of mitigating them and to put together an effective and complete package of computer programs to design asphalt concrete overlays. Another primary objective...

  20. Evaluation of healing in asphalt binders using dynamic shear rheometer and molecular modeling techniques

    E-Print Network [OSTI]

    Bommavaram, Ramamohan Reddy

    2009-05-15T23:59:59.000Z

    the parameters of characteristic healing function of asphalt binders. In the second part of this study, Molecular Modeling (MM) techniques were used to determine the interrelationship between molecular structure, surface free energy, self diffusivity, and other...

  1. Laboratory evaluation of crumb rubber asphalt concrete mixtures using the concepts of SMA mixtures 

    E-Print Network [OSTI]

    Rebala, Somasekhar Reddy

    1994-01-01T23:59:59.000Z

    Eight CRM asphalt concrete mixtures were evaluated using AAMAS characterization procedures: Four wet-process mixtures and four dry-process mixtures. These mixtures were compared to a conventional dense graded mixture. It was determined that CRM has...

  2. Automated Protocol for the Analysis of Dynamic Mechanical Analyzer Date from Fine Aggregate Asphalt Mixes 

    E-Print Network [OSTI]

    Cavalcanti De Sousa, Pedro

    2010-10-12T23:59:59.000Z

    Fatigue cracking and moisture damage are two important modes of distresses in asphalt pavements. Recently, the Dynamic Mechanical Analyzer (DMA) was used to characterize fatigue cracking and evaluate the effects of moisture ...

  3. The morphology of polymer modified asphalt and its relationship to rheology and durability

    E-Print Network [OSTI]

    Kraus, Zachary Rothman

    2008-10-10T23:59:59.000Z

    % % loglog * deg6010* deg6010 ?? , where d%A is the change in asphaltene in the asphalt (19). The other theory is that only the polar aromatics and napthene aromatics fluoresce when separated from the asphalt binder (16). Therefore as polar and napthene... aromatics change to asphaltenes with oxidative aging, the brightness would decrease. This brightness decrease would correspond to the increase in asphaltene with carbonyl area leading to a graph that looks like a chart for hardening susceptibility...

  4. Evaluation of oil shale bitumen as a pavement asphalt additive to reduce moisture damage susceptibility

    SciTech Connect (OSTI)

    Robertson, R.E.; Harnsberger, P.M.; Wolf, J.M.

    1991-01-01T23:59:59.000Z

    An unrefined shale bitumen was evaluated as an agent to reduce moisture damage susceptibility of asphalt aggregate mixtures. Some activity was observed but less than might have been expected based on the molecular weight and nitrogen content of the bitumen. The counter effects of free carboxylic acids, which are known to be variable in asphalt and which are also present in the unrefined bitumen, appear to diminish the activity of the bitumen to inhibit moisture damage. 5 refs., 1 tab.

  5. Evaluation of the effects of crumb rubber and SBR on rutting resistance of asphalt concrete

    SciTech Connect (OSTI)

    Shih, Chuang-Tsair; Tia, Mang; Ruth, B.E. [Univ. of Florida, Gainesville, FL (United States)

    1996-12-31T23:59:59.000Z

    This paper presents the results of a study to evaluate the effects of addition of crumb rubber (CR) and styrene-butadiene rubber (SBR) on the rutting resistance of asphalt concrete. These two additives were blended with an AC-20 and an AC-30 grade asphalt cements at different levels of concentrations. These modified and unmodified asphalt blends were tested at intermediate and high temperatures to evaluate their rutting resistance characteristics. They were also used to make Florida type S-I structural surface mixtures. These mixtures were made into Marshall-size specimens by using Gyratory Testing Machine (GTM) equipped with air-roller to compact and density to three compaction levels which simulate three different conditions in the pavement. The FDOT`s (Florida Department of Transportation) Loaded Wheel Tester was also used to evaluate the rutting resistance of these asphalt mixtures. The test results indicate that the modified asphalt mixtures show relatively better rutting resistance and shear resistance as compared with the unmodified asphalt mixtures.

  6. Industry Sector Case Study Building Technologies Division

    E-Print Network [OSTI]

    Fischlin, Andreas

    's remote location far away from any infrastructure, planning focused on making it as self and its control components. If needed, the system is backed up by a combined heat and power (CHP) plant might be used up, necessitating a switch to LP gas, a scarce resource at this remote location. Desigo

  7. Geothermal: Sponsored by OSTI -- Industrial Sector Technology...

    Office of Scientific and Technical Information (OSTI)

    in the United States, 1974-2000. Volume 1. Primary model documentation. Final report Geothermal Technologies Legacy Collection HelpFAQ | Site Map | Contact Us HomeBasic Search...

  8. Quality of Power in the Industrial Sector

    E-Print Network [OSTI]

    Marchbanks, G. J.

    and assistance to upgrade the quality of power into the plant. Even though studies have shown only 20% of the problems identified are actually utility generated it is the responsibility of the utility to help the customer isolate and solve the problem.... The motto of the Oklahoma Gas and Electric Quality of Power program is "If a customer perceives he has a problem, we have a problem." The commitment has been made to assist the customer until he is satis fied the problem is in fact solved. INTRODUCTION...

  9. State of the practice: Design and construction of asphalt paving materials with crumb-rubber modifier. Final report

    SciTech Connect (OSTI)

    Heitzman, M.A.

    1992-05-01T23:59:59.000Z

    The document is a comprehensive overview of the terminology, processes, products, and applications of crumb rubber modifier (CRM) technology. The technology includes any use of scrap tire rubber in asphalt paving materials. In general, CRM technology can be divided into two categories--the wet process and the dry process. When CRM is incorporated into an asphalt paving material, it will modify the properties of the binder (asphalt rubber) and/or act as a rubber aggregate (rubber modified hot mix asphalt). The five concepts for using CRM discussed in the report are McDonald, PlusRide, generic dry, chunk rubber asphalt concrete, and continuous blending asphalt rubber. There are two principal unresolved engineering issues related to the use of CRM in asphalt paving materials. On the national level, the ability to recycle asphalt paving mixes containing CRM has not been demonstrated. At the State and local levels, these modified asphalt mixes must be field evaluated to establish expected levels of performance. The appendices provide guidelines for material specifications, mix design, and construction specifications. An experimental work plan for monitoring performance and a stack emission testing program are also included.

  10. Development of statistical wet weather model to evaluate frictional properties at the pavement-tire interface on hot mix asphalt concrete

    E-Print Network [OSTI]

    Bedi, Harpreet

    2001-01-01T23:59:59.000Z

    Skid resistance on wet pavements is influenced by friction at the tire-pavement interface as well as overall hot mix asphalt (HMA) performance. It is important to control aggregate, asphalt, and mix properties to achieve desirable frictional...

  11. Application of Metagenomics for Identification of Novel Petroleum Hydrocarbon Degrading Enzymes in Natural Asphalts from the Rancho La Brea Tar Pits

    E-Print Network [OSTI]

    Baquiran, Jean-Paul Mendoza

    2010-01-01T23:59:59.000Z

    and the origin of heavy oil. Nature, 426, 344-352. HEITKAMP,natural asphalts and heavy oil compounds. A major questionmainly of asphalts and heavy oils, which have saturated into

  12. Abstract--The profound change in the electric industry worldwide in the last twenty years assigns an increasing

    E-Print Network [OSTI]

    Catholic University of Chile (Universidad Católica de Chile)

    Value. I. INTRODUCTION He reformed electric industry scheme sets the transmission sector at the center

  13. Sector 30 - useful links

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Useful Links Sector 30 Printing from your laptop at the beamline Data retrival onsite from ftp:ftp.xray.aps.anl.govpubsector30 Sector Orientation Form HERIX experiment header...

  14. Industrial Retrofits are Possible

    E-Print Network [OSTI]

    Stobart, E. W.

    . In April of 1987, the provincial government initiated a program to assist industrial energy users to reduce their energy usage. This program was designed to concentrate on an in-depth analysis of the complete operations of industrial plants... with the analyses being performed by specialist, private sector, engineering consultants. The program is in 3 phases providing an Ontario industrial plant with an Energy Analysis, a Feasibility Analysis Grant and a Project Engineering Design Grant...

  15. The Contribution of Services and other Sectors to Australian Productivity Growth 1980-2004

    E-Print Network [OSTI]

    de Gispert, Adrià

    The Contribution of Services and other Sectors to Australian Productivity Growth 1980-2004 A Report pointers to the Australian literature on sectoral productivity growth. Finally, we would like to thank ................................................................................................................................6 Labour Productivity: Macroeconomic Trends and Industry Patterns

  16. Department of Energy and Mineral Engineering Spring Roller Design to Increase the Lifespan of Asphalt Compactor Wiper Blades

    E-Print Network [OSTI]

    Demirel, Melik C.

    the Lifespan of Asphalt Compactor Wiper Blades By: Thomas Krupa, Eric Resch, Phillip Yesenosky, John Marshall, Asset Kusmanov Overview Volvo CE's asphalt compactors have a polymer wiper blade that is used life. o The roller was tested five times as long as the wipers and never showed any change in diameter

  17. Effects of carboxylic acids on the rheological properties of crumb rubber modified asphalt

    SciTech Connect (OSTI)

    Tauer, J.E.; Robertson, R.E. [Western Research Institute, Laramie, WY (United States)

    1996-12-31T23:59:59.000Z

    The Federal mandate of 1991-1995 on the use of scrap tires in Federal roadway construction sparked a major interest in gaining a fundamental understanding of the behavior of rubber in asphalt. This study is a systematic elucidation of what chemistry controls the final crumb rubber modified asphalt (CRMA) product quality. We discovered that the type and total acid content in the asphalt are the most influential chemical factors that determine the changes in the important roadway properties of shear modulus (G*) and loss angle ({delta}) of CRMA. Low acid (<0.005 m/L) asphalts were modified with three types of carboxylic acid and each made into CRMA using typical field mixing conditions of 1 hour at 175{degrees}C. Rheological measurements were then made at various storage times up to 192 hours following storage at both 156 and 200{degrees}C. We found the changes in CRMA theological properties correspond to the acid type spiked into the asphalt.

  18. NEMS industrial module documentation report

    SciTech Connect (OSTI)

    Not Available

    1994-01-01T23:59:59.000Z

    The NEMS Industrial Demand Model is a dynamic accounting model, bringing together the disparate industries and uses of energy in those industries, and putting them together in an understandable and cohesive framework. The Industrial Model generates mid-term (up to the year 2010) forecasts of industrial sector energy demand as a component of the NEMS integrated forecasting system. From the NEMS system, the Industrial Model receives fuel prices, employment data, and the value of output of industrial activity. Based on the values of these variables, the Industrial Model passes back to the NEMS system estimates of consumption by fuel types.

  19. Viscoroute 2.0: a tool for the simulation of moving load effects on asphalt pavement

    E-Print Network [OSTI]

    Chabot, Armelle; Deloffre, Lydie; Duhamel, Denis

    2010-01-01T23:59:59.000Z

    As shown by strains measured on full scale experimental aircraft structures, traffic of slow-moving multiple loads leads to asymmetric transverse strains that can be higher than longitudinal strains at the bottom of asphalt pavement layers. To analyze this effect, a model and a software called ViscoRoute have been developed. In these tools, the structure is represented by a multilayered half-space, the thermo-viscoelastic behaviour of asphalt layers is accounted by the Huet-Sayegh rheological law and loads are assumed to move at constant speed. First, the paper presents a comparison of results obtained with ViscoRoute to results stemming from the specialized literature. For thick asphalt pavement and several configurations of moving loads, other ViscoRoute simulations confirm that it is necessary to incorporate viscoelastic effects in the modelling to well predict the pavement behaviour and to anticipate possible damages in the structure.

  20. Asphalt emulsion radon barrier systems for uranium mill tailings: an overview of the technology

    SciTech Connect (OSTI)

    Baker, E.G.; Hartley, J.N.; Freeman, H.D.; Gates, T.E.; Nelson, D.A.; Dunning, R.L.

    1984-03-01T23:59:59.000Z

    Pacific Northwest Laboratory (PNL), under contract to the US Department of Energy (DOE) Uranium Mill Tailings Remedial Action Project (UMTRAP) office, has developed an asphalt emulsion cover system to reduce the release of radon from uranium mill tailings. The system has been field tested at Grand Junction, Colorado. Results from laboratory and field tests indicate that this system is effective in reducing radon release to near-background levels (<2.5 pCi m/sup -2/s/sup -1/) and has the properties required for long-term effectiveness and stability. Engineering specifications have been developed, and analysis indicates that asphalt emulsion covers are cost-competitive with other cover systems. This report summarizes the technology for asphalt emulsion radon barrier systems. 59 references, 45 figures, 36 tables.

  1. Application of pyrolized carbon black from scrap tires in asphalt pavement design and construction

    SciTech Connect (OSTI)

    Park, T.; Coree, B.J. [Indiana Department of Transportation, West Lafayette, IN (United States). Division of Research; Lovell, C.W. [Purdue Univ., West Lafayette, IN (United States). School of Civil Engineering

    1995-12-31T23:59:59.000Z

    According to EPA reports (1991) of the over 242 million waste generated each year in the United State, 5% are exported, 6% recycled, 11% incinerated, and 78% are landfilled, stockpiled, or illegally dumped. A variety of uses for these tires are being studied. Among these is pyrolysis which produces 5 5% of oil, 25% of carbon black, 9% of steel, 5% of fiber and 6% of gas. Pyrolized carbon black contains 9 % of ash, 4% of sulfur, 12% of butadine copolymer and 75% of carbon black. The objective of this research is to investigate the viability of using PCB as an additive in hot mix asphalt. The use of PCB in asphalt pavement is expected not only to improve the performance of conventional asphalt, but also to provide a means for the mass disposal of waste fires.

  2. Recycled tire rubber and other waste materials in asphalt mixtures. Transportation research record

    SciTech Connect (OSTI)

    NONE

    1995-12-31T23:59:59.000Z

    The papers in this volume, dealing with various facets of recycled tire rubber and other waste materials in asphalt mixtures, should be of interest to state and local construction, design, materials, and research engineers as well as contractors and material producers. In the first papers, Rebala and Estakhri, Malpass and Khosla, and Baker and Connolly describe research related to crumb rubber modified mixtures that was done for the Texas, North Carolina, and New Jersey State Departments of Transportation. Ali et al. report on their research in Canada to determine the feasibility of sing reclaimed roofing materials in hot mix asphalt pavement. Emery discusses the evaluation of 11 Ontario rubber modified demonstration projects in terms of pavement performance, environmental impacts, and recyclability. In the last paper, Fwa and Aziz report on their work in Singapore related to the use of incinerator residue in asphalt mixtures.

  3. 2008 Industrial Technologies Market Report, May 2009

    SciTech Connect (OSTI)

    Energetics; DOE

    2009-07-01T23:59:59.000Z

    The industrial sector is a critical component of the U.S. economy, providing an array of consumer, transportation, and national defense-related goods we rely on every day. Unlike many other economic sectors, however, the industrial sector must compete globally for raw materials, production, and sales. Though our homes, stores, hospitals, and vehicles are located within our borders, elements of our goods-producing industries could potentially be moved offshore. Keeping U.S. industry competitive is essential to maintaining and growing the U.S. economy. This report begins with an overview of trends in industrial sector energy use. The next section of the report focuses on some of the largest and most energy-intensive industrial subsectors. The report also highlights several emerging technologies that could transform key segments of industry. Finally, the report presents policies, incentives, and drivers that can influence the competitiveness of U.S. industrial firms.

  4. Energy intensity in China's iron and steel sector

    E-Print Network [OSTI]

    Xu, Jingsi, M.C.P. Massachusetts Institute of Technology

    2011-01-01T23:59:59.000Z

    In this study, I examine the spatial and economic factors that influence energy intensity in China's iron and steel sector, namely industrial value added, renovation investment, coke consumption, and local coke supply. ...

  5. Climate VISION: Private Sector Initiatives: Iron and Steel

    Office of Scientific and Technical Information (OSTI)

    Climate VISION goal of achieving a 10 percent increase in sector-wide average energy efficiency by 2012 using a 2002 baseline. Read the U.S. Steel Industry Energy Efficiency Fact...

  6. U.S. Energy Information Administration (EIA) - Sector

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    vehicles. dDoes not include lease, plant, and pipeline fuel. eNatural gas consumed in the residential and commercial sectors. f Includes consumption for industrial combined heat...

  7. U.S. Energy Information Administration (EIA) - Sector

    Gasoline and Diesel Fuel Update (EIA)

    cDoes not includes lease, plant, and pipeline fuel. dNatural gas consumed in the residential and commercial sectors. eIncludes consumption for industrial combined heat and...

  8. Studies of asphalt air blowing and development of a new short-term aging technique

    E-Print Network [OSTI]

    Vassiliev, Nicolai

    2001-01-01T23:59:59.000Z

    , Table m-2. Low temperature hardening properi. ies of air blown asphalt fractions and blends. Table III-3. Parent asphalt HS, oxidation rate, and HR . Table IV-1. Estimated time required to achieve same degrcc of aging as RTFOT for Exxon AC-10 films... of varying I. hickness . 70 Table IV-2 Effect of air blowing conditions for Exxon AC- I 0, 325 'F, 70 min. 70 Table IV-3. Condensed volatiles and RTFOT mass change . 80 Table IV-4. Reproducibility analysis. LIST OF FIGURES P ige Figure I-l. Thin film...

  9. China's Pathways to Achieving 40percent 45percent Reduction in CO2 Emissions per Unit of GDP in 2020: Sectoral Outlook and Assessment of Savings Potential

    E-Print Network [OSTI]

    Zheng, Nina

    2013-01-01T23:59:59.000Z

    heater Residential CO2 Emissions (Mt CO2) 2020 ResidentialEnergy Industrial Sector CO2 Emissions (Mt CO2) IndustrialFigure 5. Power Sector CO2 Emissions by Scenario E3 Max Tech

  10. Table 3. Top Five Retailers of Electricity, with End Use Sectors...

    U.S. Energy Information Administration (EIA) Indexed Site

    of Provider","All Sectors","Residential","Commercial","Industrial","Transportation" 1,"Green Mountain Power Corp","Investor-Owned",2477751,835602,896610,745539,0 2,"Central...

  11. Influence of coarse aggregate size, shape and surface texture on rutting of hot mix asphalt concrete

    E-Print Network [OSTI]

    Yeggoni, Mohan

    1993-01-01T23:59:59.000Z

    increased Hveem Stability, Marshall Stability and resistance to creep of hot mix asphalt concrete. The resilient modulus of the specimens was also enhanced by the increase in the amount of crushed aggregate in the mix at high temperatures (115'F). Fractal...

  12. The State of the Practice and Common Pitfalls for Porous Asphalt for

    E-Print Network [OSTI]

    of stormwater treatment systems · To provide resources to stormwater communities currently involved in design)-131 Porous Asphalt Pavements (2008) NAPA IS-115 Open-Graded Friction Courses (2002) 3 #12;Overview 1. State of the Practice 2. Water Quality Performance 3. Hydraulic Performance 4. Cold Climate

  13. Project Information Form Project Title Evaluation of the Combined Effect of Recycled Asphalt Pavement (RAP),

    E-Print Network [OSTI]

    California at Davis, University of

    Pavement (RAP), Recycled Asphalt Shingles (RAS), and Different Virgin Binder Sources on Performance of Research Project As virgin material sources become increasingly scarce, and the volume of pavement material for pavement construction. The California Department of Transportation (Caltrans) has recently increased

  14. Mixture design and performance prediction of rubber-modified asphalt in Ohio. Final report

    SciTech Connect (OSTI)

    Liang, R.Y.

    1997-08-01T23:59:59.000Z

    Appropriate disposal of scrap tires has been a major environmental concern over the years, mainly due to potential fire and health hazards associated with uncontrolled stockpiling. Primarily driven by this environmental concern, the Intermodal Surface Transportation Efficiency Act (ISTEA) of 1991 has required each State to begin incorporating scrap tire rubber into its asphalt paving materials. Although in the revision of the original ISTEA, the mandate has been eliminated, there remains a language of encouraging the use of crumb rubbers in asphalt paving materials. Ohio Department of Transportation (ODOT) desires to develop the mix design procedure, construction practice, and performance specifications for crumb rubber modified asphalt paving materials. This research was conducted to develop the needed design and construction guidance for meeting the ODOT anticipated needs. Specifically, the objectives of this research encompass the following scope: (1) investigation of the rheological properties of asphalt-rubber binder to determine optimum content of crumb rubber, (2) development of optimum mix design for various applications, including both wet and dry mix processes, (3) characterization of mechanical properties of recommended paving mixtures, including resilient modulus, fatigue cracking behavior, low-temperature thermal cracking resistance, water sensitivity test, incremental creep test and loaded wheel track test, and (4) comparison of performance of selected paving mixes.

  15. FIELD PERFORMANCE AND LABORATORY EVALUATION OF WARM MIX ASPHALT PRODUCED WITH RUBBERIZED BITUMEN

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    FIELD PERFORMANCE AND LABORATORY EVALUATION OF WARM MIX ASPHALT PRODUCED WITH RUBBERIZED BITUMEN of rubberized bitumen has been spread out mainly due to environmental aspects, but high mixing and compaction temperatures are necessary due to the higher viscosity of this bitumen. A WMA mixture (using a surfactant

  16. Creep Compliance Analysis Technique for the Flattened Indirect Tension Test of Asphalt Concrete

    E-Print Network [OSTI]

    Paulino, Glaucio H.

    Creep Compliance Analysis Technique for the Flattened Indirect Tension Test of Asphalt Concrete: ­ Cored Sample (Cylindrical) Indirect tensile testing (IDT) (Strength/Creep) ­ AASHTO T-322 Damage under and Flattened IDT · 1000-sec creep tests on three replicates · 0, -10, and -20 deg. C · Displacement

  17. Mirzahosseini et. al. ANN-Based Prediction Model for Rutting Propensity of Asphalt Mixtures1

    E-Print Network [OSTI]

    Fernandez, Thomas

    in a repeated load permanent deformation test.21 Dynamic creep test is one of the best tools for assessing of load cycles is the most23 important output of the dynamic creep test. This curve includes primary based on volumetric proportioning of the asphalt mixture. This method does16 not include any direct test

  18. Deregulating and regulatory reform in the U.S. electric power sector

    E-Print Network [OSTI]

    Joskow, Paul L.

    2000-01-01T23:59:59.000Z

    This paper discusses the evolution of wholesale and retail competition in the U.S electricity sector and associated industry restructuring and regulatory reforms. It begins with a discussion of the industry structure and ...

  19. Delivered Energy Consumption Projections by Industry in the Annual Energy Outlook 2002

    Reports and Publications (EIA)

    2002-01-01T23:59:59.000Z

    This paper presents delivered energy consumption and intensity projections for the industries included in the industrial sector of the National Energy Modeling System.

  20. Economic Crisis and the Logistics Industry: Financial Insecurity for Warehouse Workers in the Inland Empire

    E-Print Network [OSTI]

    Bonacich, Edna; De Lara, Juan David

    2009-01-01T23:59:59.000Z

    Growing the SACOG Region’s Logistics Sector: How Much, HowEconomic Crisis and the Logistics Industry Acknowledgements13 Economic Crisis and the Logistics Industry: Financial

  1. Asphalt and Asphaltic Concrete

    E-Print Network [OSTI]

    Young, A. R.

    1914-05-01T23:59:59.000Z

    , and combined curb and gutter furnished and set, the rate for resetting old curbing; the rate per cubic yard for extra concrete, if any is used; the price per cubic yard for broken stone or gravel; the rate per square yard for paving and for relaying old...- tified and given access to the same at least ten days be- fore it is required for use, and any work in which re- jected cement was used will be rejected altogether. 5. The cement shall be packed in strong bags having printed on the outside the brand...

  2. Government and Industry a Force for Collaboration at the Energy...

    Office of Environmental Management (EM)

    and Industry A Force for Collaboration at the Energy Roadmap Update Workshop Sept. 16, 2009 Energy sector leaders in the public and private sectors have once again come together to...

  3. A comparison of the fracture properties of conventional and polymer-modified two-layer asphalt concrete overlay systems 

    E-Print Network [OSTI]

    Reddy, Praveena Gutha

    1996-01-01T23:59:59.000Z

    The problem of reflection cracking through the conventional asphalt concrete overlays has increased the need to find new materials which could resist cracking or fracture more effectively. It is for this reason that polymers ...

  4. Comparison of fatigue analysis approaches for predicting fatigue lives of hot-mix asphalt concrete (HMAC) mixtures

    E-Print Network [OSTI]

    Walubita, Lubinda F.

    2006-08-16T23:59:59.000Z

    Hot-mix asphalt concrete (HMAC) mixture fatigue characterization constitutes a fundamental component of HMAC pavement structural design and analysis to ensure adequate field fatigue performance. HMAC is a heterogeneous complex composite material...

  5. Fatigue resistance of hot-mix asphalt concrete (HMAC) mixtures using the calibrated mechanistic with surface energy (CMSE) measurements approach

    E-Print Network [OSTI]

    Ofori-Abebresse, Edward Kwame

    2006-10-30T23:59:59.000Z

    Fatigue cracking is one of the fundamental distresses that occur in the life of a Hot Mix Asphalt Concrete (HMAC) pavement. This load induced distress leads to structural collapse of the entire pavement ultimately and can only be remedied...

  6. Fatigue resistance of hot-mix asphalt concrete (HMAC) mixtures using the calibrated mechanistic with surface energy (CMSE) measurements approach 

    E-Print Network [OSTI]

    Ofori-Abebresse, Edward Kwame

    2006-10-30T23:59:59.000Z

    Fatigue cracking is one of the fundamental distresses that occur in the life of a Hot Mix Asphalt Concrete (HMAC) pavement. This load induced distress leads to structural collapse of the entire pavement ultimately and can ...

  7. A unified method for the analysis of nonlinear viscoelasticity and fatigue cracking of asphalt mixtures using the dynamic mechanical analyzer

    E-Print Network [OSTI]

    Castelo Branco, Veronica Teixeira Franco

    2009-05-15T23:59:59.000Z

    A UNIFIED METHOD FOR THE ANALYSIS OF NONLINEAR VISCOELASTICITY AND FATIGUE CRACKING OF ASPHALT MIXTURES USING THE DYNAMIC MECHANICAL ANALYZER A Dissertation by VERONICA TEIXEIRA FRANCO CASTELO BRANCO Submitted to the Office... VISCOELASTICITY AND FATIGUE CRACKING OF ASPHALT MIXTURES USING THE DYNAMIC MECHANICAL ANALYZER A Dissertation by VERONICA TEIXEIRA FRANCO CASTELO BRANCO Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment...

  8. A study of substitution solvents in asphalt fume extraction and the effects of heating duration and temperature 

    E-Print Network [OSTI]

    Curry, Noel Thomas

    1981-01-01T23:59:59.000Z

    may be used as substitute solvents for the solvent extraction analytical method for asphalt furres proposed by NlnSH and currently in use by OSHA. Benzene is known to orovide IC0% effic- 1 iency in asphalt fume extraction. The results..., rather than the solvents' effic- iency loss, was responsible for the differences. The importance of the data lies in the fact that the other two test solvents exhibited a consiatency equal to that of benzene. 'Ahile the exact coefficient of any...

  9. asphalt rubber mixtures: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Jerry G. Murphy 2013-01-23 112 Material: Recycled Rubber from Tires, Industrial Scrap CiteSeer Summary: using the ambient desert heat (160-220F). The process was brought...

  10. Barriers to Industrial Energy Efficiency- Study (Appendix A), June 2015

    Broader source: Energy.gov [DOE]

    This study examines barriers that impede the adoption of energy efficient technologies and practices in the industrial sector, and identifies successful examples and opportunities to overcome these...

  11. Barriers to Industrial Energy Efficiency- Report to Congress, June 2015

    Broader source: Energy.gov [DOE]

    This report examines barriers that impede the adoption of energy efficient technologies and practices in the industrial sector, and identifies successful examples and opportunities to overcome...

  12. China’s Defense Electronics Industry: Innovation, Adaptation, and Espionage

    E-Print Network [OSTI]

    Mulvenon, James; Luce, Matthew

    2010-01-01T23:59:59.000Z

    2010 China’s Defense Electronics Industry: Innovation,of the Chinese defense electronics sector can be attributedAdvanced defense electronics components and systems play a

  13. Advanced, Energy-Efficient Hybrid Membrane System for Industrial...

    Energy Savers [EERE]

    (1 slide) Develo Project Objecve Current StateChallenges Heavy industrial water utilization footprint Freshwater Withdrawals in the U.S. by Sector (2005) Domestic...

  14. An analysis of some properties of paving asphalts in Texas as they relate to pavement performance

    E-Print Network [OSTI]

    DuBose, Emmett Haygood

    1980-01-01T23:59:59.000Z

    51 73 93 115 115 DISTRESS AND CRACKING FACTORS THE PAVEMENT PERFORMANCE SYSTEM 5 CONCLUSIONS AND RECOMMENDATIONS CONCLUSIONS RECOMMENDATIONS REFERENCES . APPENDIX A: RAW DATA APPENDIX B: PAVEMENT PERFORMANCE VS. TIME CURVES APPENDIX C... harden1ng model. It had been shown in earlier research that excessive asphalt1c concrete binder hardening was a detrimental factor influencing certain types of pavement distress such as thermal cracking, raveling, fatigue cracking, and reflective crack...

  15. Thickness estimation of subsurface layers in asphalt pavement using monstatic ground penetrating radar

    E-Print Network [OSTI]

    Lau, Chun Lok

    1991-01-01T23:59:59.000Z

    for the degree of MASTER OF SCIENCE December 1991 Major Subject: Electrical Engineering THICKNESS ESTIMATION OF SUBSURFACE LAYERS IN ASPHALT PAVEMENT USING MONSTATIC GROUND PENETRATING RADAR A Thesis CHUN LOK LAU Approved as to style and content by... ACKNOWLEDGEMENTS. LIST OF FIGURES. . CHAPTER I INTRODUCTION. 1. 1 Importance of pavement profile data. 1. 2 Principle of Ground Penetrating Radar (GPR) . . . 1. 3 Subsurface layer thickness measurement method. . . . . . II GPR ANTENNA AND SYSTEM CALIBRATION...

  16. Oxidative reactions and their impact on the properties of asphalt as a pavement binder

    E-Print Network [OSTI]

    Lau, Chee Keung

    1991-01-01T23:59:59.000Z

    mechanical spectrometer was found to increase with aging time. Correlation was shown to exist between the limiting complex viscosity and the carbonyl area as determined by infrared analysis. The correlation was unique for each asphalt and was independent... of aging temperature. The carbonyl area growth rate was a strong function of the aging temperature and the temperature dependence of the rate constant followed the Arrhenius relation within the temperature range tested. The results led...

  17. Viscosity, relaxation time, and dynamics within a model asphalt of larger molecules

    SciTech Connect (OSTI)

    Li, Derek D.; Greenfield, Michael L., E-mail: greenfield@egr.uri.edu [Department of Chemical Engineering, University of Rhode Island, Kingston, Rhode Island 02881 (United States)

    2014-01-21T23:59:59.000Z

    The dynamics properties of a new “next generation” model asphalt system that represents SHRP AAA-1 asphalt using larger molecules than past models is studied using molecular simulation. The system contains 72 molecules distributed over 12 molecule types that range from nonpolar branched alkanes to polar resins and asphaltenes. Molecular weights range from 290 to 890 g/mol. All-atom molecular dynamics simulations conducted at six temperatures from 298.15 to 533.15 K provide a wealth of correlation data. The modified Kohlrausch-Williams-Watts equation was regressed to reorientation time correlation functions and extrapolated to calculate average rotational relaxation times for individual molecules. The rotational relaxation rate of molecules decreased significantly with increasing size and decreasing temperature. Translational self-diffusion coefficients followed an Arrhenius dependence. Similar activation energies of ?42 kJ/mol were found for all 12 molecules in the model system, while diffusion prefactors spanned an order of magnitude. Viscosities calculated directly at 533.15 K and estimated at lower temperatures using the Debye-Stokes-Einstein relationship were consistent with experimental data for asphalts. The product of diffusion coefficient and rotational relaxation time showed only small changes with temperature above 358.15 K, indicating rotation and translation that couple self-consistently with viscosity. At lower temperatures, rotation slowed more than diffusion.

  18. applications radioprotecao industrial: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    16 17 18 19 20 21 22 23 24 25 Next Page Last Page Topic Index 421 National Industrial Hemp Strategy ii March 2008Executive Summary Growth of the Canadian Industrial Hemp Sector...

  19. arab oil industry: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    U.S. Impact and Strategies (3) TECH 562 Kostic, Milivoje M. 492 National Industrial Hemp Strategy ii March 2008Executive Summary Growth of the Canadian Industrial Hemp Sector...

  20. Development of asphalts and pavements using recycled tire rubber. Phase 1, Technical feasibility. Technical progress report, September 1, 1994--August 31, 1995

    SciTech Connect (OSTI)

    Bullin, J.A.; Davison, R.R.; Glover, C.J. [and others

    1996-06-01T23:59:59.000Z

    About 285 million tires are discarded every year; less than 100 million are currently being recycled, with the rest being placed in landfills and other waste sites. A solution to reduce the littering of the environment is to use ground tire rubber in road construction. Currently, about 27 million tons of asphalt are used each year in road construction and maintenance of the country`s 2 million miles of roads. If all of the waste tire rubber could be combined with asphalt in road construction, it would displace less than 6% of the total asphalt used each year, yet could save about 60 trillion Btus annually. Purpose of this project is to provide data needed to optimize the performance of rubber-asphalt concretes. The first phase is to develop asphalts and recycling agents tailored for compatibility with ground tire rubber. Chapter 2 presents results on Laboratory Testing and Evaluation: fractionate asphalt material, reblending for aromatic asphalts, verifying optimal curing parameters, aging of blends, and measuring ductilities of asphalt-rubber binders. Chapter 3 focuses on Evaluating Mixture Characteristics (modified binders). Chapter 4 covers Adhesion Test Development (water susceptibility is also covered). The final chapter focuses on the Performance/Economic Update and Commercialization Plan.

  1. Industrial Permit

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Protection Obeying Environmental Laws Industrial Permit Industrial Permit The Industrial Permit authorizes the Laboratory to discharge point-source effluents under the...

  2. Hepp and Speer Sectors within Modern Strategies of Sector Decomposition

    E-Print Network [OSTI]

    A. V. Smirnov; V. A. Smirnov

    2008-12-26T23:59:59.000Z

    Hepp and Speer sectors were successfully used in the sixties and seventies for proving mathematical theorems on analytically or/and dimensionally regularized and renormalized Feynman integrals at Euclidean external momenta. We describe them within recently developed strategies of introducing iterative sector decompositions. We show that Speer sectors are reproduced within one of the existing strategies.

  3. Industrial Applications for Micropower: A Market Assessment,...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    generation equipment less than 1 MW) such as microturbines, fuel cells, and reciprocating engines offers promise to renew growth in the U.S. industrial sector. Based on the...

  4. Development Requirements for Advanced Industrial Heat Pumps 

    E-Print Network [OSTI]

    Chappell, R. N.; Priebe, S. J.; Bliem, C. J.; Mills, J. I.

    1985-01-01T23:59:59.000Z

    DOE is attempting to advance the use of heat pumps to save energy in industrial processes. The approach has emphasized developing better heat pump technology and transferring that technology to the private sector. DOE requires that heat pump...

  5. Development Requirements for Advanced Industrial Heat Pumps

    E-Print Network [OSTI]

    Chappell, R. N.; Priebe, S. J.; Bliem, C. J.; Mills, J. I.

    DOE is attempting to advance the use of heat pumps to save energy in industrial processes. The approach has emphasized developing better heat pump technology and transferring that technology to the private sector. DOE requires that heat pump...

  6. Experimental Study on Shear Fatigue Behavior and Stiffness Performance of Warm Mix Asphalt by adding Synthetic Wax

    E-Print Network [OSTI]

    Petit, Christophe; Canestrari, Francesco; Pannunzio, Valter; Virgili, Amadeo

    2012-01-01T23:59:59.000Z

    Synthetic waxes produced by standard and registered processes may be used to manufacture Warm Mix Asphalt (WMA), which is a modified asphalt concrete produced, applied and compacted at temperatures below those typically required. This feature leads to environmental benefits, such as reduced energy consumption, gas and fume emissions, as well as to economic/operational advantages, such as lower production costs and greater hauling distances for extended construction seasons with tighter schedules. The present article serves to compare the mechanical performance of a WMA produced by adding synthetic wax with a traditional Hot Mix Asphalt (HMA) specimen, in terms of shear fatigue response and both complex and stiffness moduli. The experimental results and related modeling work demonstrate that adding synthetic wax into the WMA composition does not hinder either the destructive or non-destructive performance of an HMA, and this finding is corroborated by respectively measuring fatigue life and stiffness.

  7. Experimental Study on Shear Fatigue Behavior and Stiffness Performance of Warm Mix Asphalt by adding Synthetic Wax

    E-Print Network [OSTI]

    Christophe Petit; Anne Millien; Francesco Canestrari; Valter Pannunzio; Amadeo Virgili

    2012-03-13T23:59:59.000Z

    Synthetic waxes produced by standard and registered processes may be used to manufacture Warm Mix Asphalt (WMA), which is a modified asphalt concrete produced, applied and compacted at temperatures below those typically required. This feature leads to environmental benefits, such as reduced energy consumption, gas and fume emissions, as well as to economic/operational advantages, such as lower production costs and greater hauling distances for extended construction seasons with tighter schedules. The present article serves to compare the mechanical performance of a WMA produced by adding synthetic wax with a traditional Hot Mix Asphalt (HMA) specimen, in terms of shear fatigue response and both complex and stiffness moduli. The experimental results and related modeling work demonstrate that adding synthetic wax into the WMA composition does not hinder either the destructive or non-destructive performance of an HMA, and this finding is corroborated by respectively measuring fatigue life and stiffness.

  8. Establishing material properties for thin asphalt concrete surfaces on granular bases

    E-Print Network [OSTI]

    Rosson, Barry Thomas

    1985-01-01T23:59:59.000Z

    cross-section of a Goodyear Hi -Miler 10. 00-20 14-ply bias truck tire carcass was obtained; the input data for the Tielking tire model was developed by measuring cord locations, angles, and plies on a section of the tire; and the tire pressure.... Since little work in the past has been done in the area of thin asphalt concrete surface analysis, re-evaluation of several assumptions concerning the tire load were necessary. The truck tire pressures on Texas highways have dramatically increased...

  9. The Effects of Using Alkali-Silica Reaction Affected Recycled Concrete Aggregate in Hot Mix Asphalt

    E-Print Network [OSTI]

    Geiger, Brian James

    2011-10-21T23:59:59.000Z

    mix asphalt (HMA) were investigated in this study. Dilatometer and modified beam tests were performed to determine the possibility of new ASR occurring in reactive aggregates within the HMA or re-expansion of existing gel. The Lottman test... (XRD) was used to check for the potential presence of gel in the filler fraction of the ASR-RCAs. Micro-deval and freeze-thaw tests were evaluated for their potential to indicate the presence of excess micro-cracks or ASR gel. Expansion testing...

  10. Whole House Thermal Performance of Asphalt Shingles Exploiting Special Infrared Reflective Pigments

    E-Print Network [OSTI]

    Hahn, L.; Miller, W.; Desjarlais, A.; Jacobs, J.; Youngquist, A.

    2006-01-01T23:59:59.000Z

    -04 using cycle 4 as described in Table X2.1, Common Exposure Conditions, of the G 154 standard (ASTM 2002b). A UVB-340 lamp was used for simulating direct solar UV radiation; this lamp has no UV output below 300 nm, which is the cutoff wavelength... for this behavior is unknown; overall, however, the data clearly show that the IRR shingles perform just as well when subjected to direct solar UV radiation as standard products accepted on the open market. The IRR asphalt shingles do not lose solar reflectance...

  11. Multi-Sector

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHighandSWPA / SPRA /Ml'.SolarUS Dept ofActing Chiefof Inks andmulti-sector

  12. Promoting Green Jobs in the Building and Construction Sector

    E-Print Network [OSTI]

    Promoting Green Jobs in the Building and Construction Sector BUILDING FOR ECOLOGICALLY RESPONSIVE Industries" SMX Convention Center, Pasay City CHRISTOPHER CRUZ DE LA CRUZ Philippine Green Building Council 8 the ability of future generations to meet their own needs" #12;· "The fastest growing regional green building

  13. Power Politics: The Political Economy of Russia's Electricity Sector Liberalization

    E-Print Network [OSTI]

    Wengle, Susanne Alice

    2010-01-01T23:59:59.000Z

    electricity sector assets and prices to prevent de- industrialization and cushion the impact of hyperinflation on householdelectricity to “households and other socially-important consumer groups” at priceshousehold incomes, and price increases will not go unnoticed. 862 Russians also care about reliable electricity

  14. Advanced Vehicle Electrification & Transportation Sector Electrificati...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    & Transportation Sector Electrification Advanced Vehicle Electrification & Transportation Sector Electrification 2011 DOE Hydrogen and Fuel Cells Program, and Vehicle Technologies...

  15. Energy Sector Cybersecurity Framework Implementation Guidance

    Broader source: Energy.gov (indexed) [DOE]

    DRAFT FOR PUBLIC COMMENT SEPTEMBER, 2014 ENERGY SECTOR CYBERSECURITY FRAMEWORK IMPLEMENTATION GUIDANCE Energy Sector Cybersecurity Framework Implementation Guidance Table of...

  16. Presentation 2.2: Biofuels -A Strategic Option for the Global Forest Sector? Michael Obersteiner

    E-Print Network [OSTI]

    Presentation 2.2: Biofuels - A Strategic Option for the Global Forest Sector? Michael Obersteiner Generation Biofuels. We will close with a SWOT analysis of the forest sector vis-à-vis the oil industry the emerging big player on the biofuels market. 117 #12;#12;Michael Obersteiner & Sten Nilsson International

  17. Porous Asphalt Pavement for Stormwater Management The UNH Stormwater Center Web: www.unh.edu/erg/cstev/

    E-Print Network [OSTI]

    Porous Asphalt Pavement for Stormwater Management The UNH Stormwater Center Web: www. Extended Pavement Life Due to Well Drained Base and Reduced Freeze-Thaw Disadvantages · Requires Routine. Standard Pavement Applications where Stormwater Infrastructure is Required · Materials Cost is ~20-25% More

  18. SOURCE: UNIVERSITY OF CALIFORNIA PAVEMENT RESEARCH CENTER FIGURE 1 Moisture-induced stripping in asphalt treated base layer

    E-Print Network [OSTI]

    California at Berkeley, University of

    SOURCE: UNIVERSITY OF CALIFORNIA PAVEMENT RESEARCH CENTER FIGURE 1 Moisture-induced stripping in asphalt treated base layer PAVEMENT TECHNOLOGY UPDATE This Technology Transfer Program publication is provided by the University of California Pavement Research Center. The University of California Pavement

  19. Recycling spent sandblasting grit and similar wastes as aggregate in asphaltic concrete. Technical data sheet

    SciTech Connect (OSTI)

    Heath, J.C.; Nelson, B.

    1998-12-01T23:59:59.000Z

    The Naval Facilities Engineering Service Center (NFESC), Port Hueneme, California, and Naval Facilities Engineering Command Engineering Field Activity, West, San Bruno, California, took overall leadership in identifying and testing methods to manage waste generated from a machine shop located at Hunters Point Annex, at Naval Station, Treasure Island, California. Ship cleaning and equipment maintenance resulted in the accumulation of 4,665 tons of spent sandblasting grit at the site. The spent grit, consisting of silica sand plus a small amount of slag-derived grit, had the physical characteristics of coarse-grained beach sand and also contained fragments of coatings. The spent grit had the potential for exhibiting hazardous characteristics since the coatings included lead-based primers, copper, and butyltin-containing antifouling topcoats. The most beneficial application of reusing the spent grit was to use it as a replacement for some of the fine aggregate in asphaltic concrete. A test program was established that included characterization, bench-scale testing, long-term pilot scale testing, and a full-scale demonstration. Full-scale asphalt production provided samples which proved both the chemical leaching resistance and physical performance characteristics were acceptable.

  20. Industrial Engineering Industrial Advisory Board

    E-Print Network [OSTI]

    Gelfond, Michael

    Industrial Engineering Industrial Advisory Board (IAB) #12;PURPOSE: The Texas Tech University - Industrial Engineering Industrial Ad- visory Board (IAB) is an association of professionals with a com- mon goal - promoting and developing the Texas Tech Department of Industrial Engineering and its students

  1. Energy Sector Market Analysis

    SciTech Connect (OSTI)

    Arent, D.; Benioff, R.; Mosey, G.; Bird, L.; Brown, J.; Brown, E.; Vimmerstedt, L.; Aabakken, J.; Parks, K.; Lapsa, M.; Davis, S.; Olszewski, M.; Cox, D.; McElhaney, K.; Hadley, S.; Hostick, D.; Nicholls, A.; McDonald, S.; Holloman, B.

    2006-10-01T23:59:59.000Z

    This paper presents the results of energy market analysis sponsored by the Department of Energy's (DOE) Weatherization and International Program (WIP) within the Office of Energy Efficiency and Renewable Energy (EERE). The analysis was conducted by a team of DOE laboratory experts from the National Renewable Energy Laboratory (NREL), Oak Ridge National Laboratory (ORNL), and Pacific Northwest National Laboratory (PNNL), with additional input from Lawrence Berkeley National Laboratory (LBNL). The analysis was structured to identify those markets and niches where government can create the biggest impact by informing management decisions in the private and public sectors. The analysis identifies those markets and niches where opportunities exist for increasing energy efficiency and renewable energy use.

  2. Industrial energy efficiency policy in China

    SciTech Connect (OSTI)

    Price, Lynn; Worrell, Ernst; Sinton, Jonathan; Yun, Jiang

    2001-05-01T23:59:59.000Z

    Chinese industrial sector energy-efficiency policy has gone through a number of distinct phases since the founding of the People s Republic in 1949. An initial period of energy supply growth in the 1950s, 1960s, and 1970s was followed by implementation of significant energy efficiency programs in the 1980s. Many of these programs were dismantled in the 1990s during the continuing move towards a market-based economy. In an effort to once again strengthen energy efficiency, the Chinese government passes the Energy Conservation Law in 1997 which provides broad guidance for the establishment of energy efficiency policies. Article 20 of the Energy Conservation Law requires substantial improvement in industrial energy efficiency in the key energy-consuming industrial facilities in China. This portion of the Law declares that ''the State will enhance energy conservation management in key energy consuming entities.'' In 1999, the industrial sector consumed nearly 30 EJ, or 76 percent of China's primary energy. Even though primary energy consumption has dropped dramatically in recent years, due mostly to a decline in coal consumption, the Chinese government is still actively developing an overall policy for energy efficiency in the industrial sector modeled after policies in a number of industrialized countries. This paper will describe recent Chinese government activities to develop industrial sector energy-efficiency targets as a ''market-based'' mechanism for improving the energy efficiency of key industrial facilities.

  3. Public Sector Electric Efficiency Programs

    Broader source: Energy.gov [DOE]

    The Illinois Department of Commerce and Economic Opportunity (DCEO) Bureau of Energy and Recycling administers the public sector energy efficiency programs required by the Illinois Energy...

  4. Excess Foundry Sand Characterization and Experimental Investigation in Controlled Low-Strength Material and Hot-Mixing Asphalt

    SciTech Connect (OSTI)

    Paul J. Tikalsky, Hussain U. Bahia, An Deng and Thomas Snyder

    2004-10-15T23:59:59.000Z

    This report provides technical data regarding the reuse of excess foundry sand. The report addresses three topics: a statistically sound evaluation of the characterization of foundry sand, a laboratory investigation to qualify excess foundry sand as a major component in controlled low-strength material (CLSM), and the identification of the best methods for using foundry sand as a replacement for natural aggregates for construction purposes, specifically in asphalt paving materials. The survival analysis statistical technique was used to characterize foundry sand over a full spectrum of general chemical parameters, metallic elements, and organic compounds regarding bulk analysis and leachate characterization. Not limited to characterization and environmental impact, foundry sand was evaluated by factor analyses, which contributes to proper selection of factor and maximization of the reuse marketplace for foundry sand. Regarding the integration of foundry sand into CLSM, excavatable CLSM and structural CLSM containing different types of excess foundry sands were investigated through laboratory experiments. Foundry sand was approved to constitute a major component in CLSM. Regarding the integration of foundry sand into asphalt paving materials, the optimum asphalt content was determined for each mixture, as well as the bulk density, maximum density, asphalt absorption, and air voids at Nini, Ndes, and Nmax. It was found that foundry sands can be used as an aggregate in hot-mix asphalt production, but each sand should be evaluated individually. Foundry sands tend to lower the strength of mixtures and also may make them more susceptible to moisture damage. Finally, traditional anti-stripping additives may decrease the moisture sensitivity of a mixture containing foundry sand, but not to the level allowed by most highway agencies.

  5. Excess Foundry Sand Characterization and Experimental Investigation in Controlled Low-Strength Material and Hot-Mixing Asphalt

    SciTech Connect (OSTI)

    Pauul J. Tikalsky

    2004-10-31T23:59:59.000Z

    This report provides technical data regarding the reuse of excess foundry sand. The report addresses three topics: (1) a statistically sound evaluation of the characterization of foundry sand, (2) a laboratory investigation to qualify excess foundry sand as a major component in controlled low-strength material (CLSM), and (3) the identification of the best methods for using foundry sand as a replacement for natural aggregates for construction purposes, specifically in asphalt paving materials. The survival analysis statistical technique was used to characterize foundry sand over a full spectrum of general chemical parameters, metallic elements, and organic compounds regarding bulk analysis and leachate characterization. Not limited to characterization and environmental impact, foundry sand was evaluated by factor analyses, which contributes to proper selection of factor and maximization of the reuse marketplace for foundry sand. Regarding the integration of foundry sand into CLSM, excavatable CLSM and structural CLSM containing different types of excess foundry sands were investigated through laboratory experiments. Foundry sand was approved to constitute a major component in CLSM. Regarding the integration of foundry sand into asphalt paving materials, the optimum asphalt content was determined for each mixture, as well as the bulk density, maximum density, asphalt absorption, and air voids at N{sub ini}, N{sub des}, and N{sub max}. It was found that foundry sands can be used as an aggregate in hot-mix asphalt production, but each sand should be evaluated individually. Foundry sands tend to lower the strength of mixtures and also may make them more susceptible to moisture damage. Finally, traditional anti-stripping additives may decrease the moisture sensitivity of a mixture containing foundry sand, but not to the level allowed by most highway agencies.

  6. Two- and Three-Dimensional Microstructural Modeling of Asphalt Particulate Composite Materials using a Unified Viscoelastic-Viscoplastic-Viscodamage Constitutive Model

    E-Print Network [OSTI]

    You, Taesun

    2013-08-13T23:59:59.000Z

    The main objective of this study is to develop and validate a framework for microstructural modeling of asphalt composite materials using a coupled thermo-viscoelastic, thermo-viscoplastic, and thermo-viscodamage constitutive model. In addition...

  7. Energy Efficiency Improvement and Cost Saving Opportunities for the Dairy Processing Industry

    E-Print Network [OSTI]

    Brush, Adrian

    2012-01-01T23:59:59.000Z

    industrial sectors. Modern control systems are often notmay already have modern process control systems in place togrowing rapidly. Modern process control systems exist for

  8. ITL BULLETIN FOR AUGUST 2011 PROTECTING INDUSTRIAL CONTROL SYSTEMS KEY COMPONENTS OF

    E-Print Network [OSTI]

    , transportation, healthcare, and emergency services sectors. Federal agencies also operate critical production, handling, and distribution. ICS are used in many industries: electric, water, oil and gas

  9. HTGR Industrial Application Functional and Operational Requirements

    SciTech Connect (OSTI)

    L. E. Demick

    2010-08-01T23:59:59.000Z

    This document specifies the functional and performance requirements to be used in the development of the conceptual design of a high temperature gas-cooled reactor (HTGR) based plant supplying energy to a typical industrial facility. These requirements were developed from collaboration with industry and HTGR suppliers over the preceding three years to identify the energy needs of industrial processes for which the HTGR technology is technically and economically viable. The functional and performance requirements specified herein are an effective representation of the industrial sector energy needs and an effective basis for developing a conceptual design of the plant that will serve the broadest range of industrial applications.

  10. Use of shredded tires in the subbase layer of asphalt pavements

    SciTech Connect (OSTI)

    Papp, W.J. Jr.; Maher, M.H. [Rutgers Univ., Piscataway, NJ (United States). Dept. of Civil and Environmental Engineering; Baker, R.F. [New Jersey Dept. of Transportation, Trenton, NJ (United States)

    1997-12-31T23:59:59.000Z

    Research was conducted on the use of shredded scrap tires for use in the subbase layer of asphalt pavements. Mixtures of shredded scrap tires with virgin soil provide a means of recycling unwanted tires and conserving a finite supply of virgin soil. The mechanistic procedure for the design of pavement systems requires resilient modulus values. Plastic and elastic strains were measured using external LVDT`s and internal proximity sensors. Resilient modulus measurements were conducted on cohesionless soils mixed with various amounts of shredded tire chips. The performance f the shredded tire mixture is compared to that of the naturally occurring virgin soil used in subbase applications in New Jersey. A number of experimental issues are discussed such as: method of compaction, optimum ratio of shredded tire chips to soil, optimum size and gradation of shredded tire chips, and strength testing using California Bearing Ratio.

  11. Greenhouse Gas Programs, Energy Efficiency, and the Industrial Sector

    E-Print Network [OSTI]

    Zhou, A.; Tutterow, V.; Harris, J.

    The United States has made significant progress in reducing total energy use through energy efficiency improvements over the past decade, yet the United States still ranks as the highest absolute greenhouse gas (GHG) emitter in the world with 23...

  12. Efficient Energy Utilization in the Industrial Sector - Case Studies

    E-Print Network [OSTI]

    Davis, S. R.

    1984-01-01T23:59:59.000Z

    . Leakage and misuse of compressed air can normally be reduced by 10 percent, resulting in an annual savings of approximately $10,000 to $20,000. Heat recovery, using air compressor cooling water, can and is being used for space heating...

  13. World Best Practice Energy Intensity Values for Selected Industrial Sectors

    E-Print Network [OSTI]

    Worrell, Ernst; Price, Lynn; Neelis, Maarten; Galitsky, Christina; Zhou, Nan

    2007-01-01T23:59:59.000Z

    feedstock, followed by heavy oil, which requires an averageammonia is made from heavy oil and coal, which is much lesspartial oxidization of heavy fuel oil, gasification of coal,

  14. World Best Practice Energy Intensity Values for Selected Industrial Sectors

    E-Print Network [OSTI]

    Worrell, Ernst; Price, Lynn; Neelis, Maarten; Galitsky, Christina; Zhou, Nan

    2007-01-01T23:59:59.000Z

    in a back-pressure steam turbine to generate electricity (compressor uses a steam turbine, using internally generatedwith a gas turbine, producing steam and electricity. The hot

  15. Industrial Sector Energy Efficiency Modeling (ISEEM) Framework Documentation

    E-Print Network [OSTI]

    Karali, Nihan

    2014-01-01T23:59:59.000Z

    Energy Supply Modeling Package EFOM-12C Mark 1 MathematicalEnergy Supply Modeling Package EFOM-12C Mark 1 User’s Guide,the Economy EU European Union EFOM Energy Flow Optimization

  16. Labor's Share By Sector And Industry, 1948-1965

    E-Print Network [OSTI]

    Close, Frank A.; Shulenburger, David E.

    1971-01-01T23:59:59.000Z

    .6548 0.8667 0.8742 0.6078 0.6050 0.4867 0.7133 0.7113 0.6700 0.6553 0.8821 0.8888 0.6007 0.5978 0.4652 0.7465 0.7445 0.6829 0.6641 0.8709 0.8760 0.5934 0.5909 0.4666 0.7409 0.7389 0.6809 0.6649 0.8686 0.8810 0.5784 0.5757 0.4640 0.7393 0.7372 0.6828 0...

  17. World Best Practice Energy Intensity Values for Selected Industrial Sectors

    E-Print Network [OSTI]

    Worrell, Ernst; Price, Lynn; Neelis, Maarten; Galitsky, Christina; Zhou, Nan

    2007-01-01T23:59:59.000Z

    1996. COREX, Revolution in Ironmaking, Linz, Austria:VAI. ;GJ/t Material Preparation Ironmaking Sintering PelletizingGJ/t Material Preparation Ironmaking Sintering Pelletizing

  18. World Best Practice Energy Intensity Values for Selected Industrial Sectors

    E-Print Network [OSTI]

    Worrell, Ernst; Price, Lynn; Neelis, Maarten; Galitsky, Christina; Zhou, Nan

    2007-01-01T23:59:59.000Z

    D.W. , M.T. Towers and T.C. Browne. 2002. Energy CostD.W. , M.T. Towers and T.C. Browne. 2002. Energy CostD.W. , M.T. Towers and T.C. Browne. 2002. Energy Cost

  19. World Best Practice Energy Intensity Values for Selected Industrial Sectors

    E-Print Network [OSTI]

    Worrell, Ernst; Price, Lynn; Neelis, Maarten; Galitsky, Christina; Zhou, Nan

    2007-01-01T23:59:59.000Z

    recovered from the black liquor recovery process (combustingand development in black liquor gasification has not yetgreen liquor”, similar to the black liquor recovery process,

  20. Industrial Sector Energy Efficiency Modeling (ISEEM) Framework Documentation

    E-Print Network [OSTI]

    Karali, Nihan

    2014-01-01T23:59:59.000Z

    INVESTMENT COST . anninvcost Annualized investment cost of a technology bound_Total of discounted investment costs discinvcost Discounted

  1. World Best Practice Energy Intensity Values for Selected Industrial Sectors

    E-Print Network [OSTI]

    Worrell, Ernst; Price, Lynn; Neelis, Maarten; Galitsky, Christina; Zhou, Nan

    2007-01-01T23:59:59.000Z

    can be produced onsite at the smelter or in separate plants19, 20 The most efficient smelters consume 400-440 kg ofyears five aluminum smelter types have become widespread:

  2. Designing Effective State Programs for the Industrial Sector - New SEE

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE: Alternative FuelsNovember 13, 2014ContributingDOEDepartment of EnergySmallDesign GuideAction

  3. Fact #619: April 19, 2010 Transportation Sector Revenue by Industry |

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport in RepresentativeDepartment of EnergyEnergy 5: March 22, 2010Statistics

  4. Table E5. Industrial Sector Energy Price Estimates, 2012

    Gasoline and Diesel Fuel Update (EIA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for On-Highway4,1,50022,3,,,,6,1,9,1,50022,3,,,,6,1,Decade Energy I I' a(STEO)U.S. CoalInputsTotal Stocks4. ElectricE4.E5.

  5. Coal Industry Annual 1995

    SciTech Connect (OSTI)

    NONE

    1996-10-01T23:59:59.000Z

    This report presents data on coal consumption, coal distribution, coal stocks, coal prices, coal quality, and emissions for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States. This report does not include coal consumption data for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. Consumption for nonutility power producers not included in this report is estimated to be 21 million short tons for 1995.

  6. Coal industry annual 1996

    SciTech Connect (OSTI)

    NONE

    1997-11-01T23:59:59.000Z

    This report presents data on coal consumption, coal distribution, coal stocks, coal prices, and coal quality, and emissions for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States.This report does not include coal consumption data for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. Consumption for nonutility power producers not included in this report is estimated to be 24 million short tons for 1996. 14 figs., 145 tabs.

  7. The dynamics of technology di?usion and the impacts of climate policy instruments in the decarbonisation of the global electricity sector

    E-Print Network [OSTI]

    Mercure, J.-F.; Pollitt, H.; Chewpreecha, U.; Salas, P.; Foley, A. M.; Holden, P. B.; Edwards, N. R.

    2014-07-16T23:59:59.000Z

    as exogenous trends of emissions for non-fuel-related sectors (e.g. land use), obtained from the EDGAR database. While the changes modelled include those in power sector emissions, they also include modest changes in other sectors (e.g. industry) occurring due...

  8. Solar-Assisted Technology Provides Heat for California Industries

    E-Print Network [OSTI]

    Solar-Assisted Technology Provides Heat for California Industries Industrial/Agriculture/Water End 2011 The Issue Solar thermal technology focuses the Sun's rays to heat water, and is a promising renewable resource for California's industrial sector. Commercially available solar water heating

  9. Understanding Sectoral Labor Market Dynamics: An Equilibrium Analysis of the Oil and Gas Field Services

    E-Print Network [OSTI]

    Sadoulet, Elisabeth

    Understanding Sectoral Labor Market Dynamics: An Equilibrium Analysis of the Oil and Gas Field examines the response of employment and wages in the US oil and gas ...eld services industry to changes the dynamic response of wages and employment in the U.S. Oil and Gas Field Services (OGFS) industry to changes

  10. A New, Stochastic, Energy Model of the U.S. is Under Construction: SEDS and Its Industrial Structure

    E-Print Network [OSTI]

    Roop, J. M.

    -duty vehicles and heavy-duty vehicles. The industrial sector is currently modeled as a single sector, using the latest Manufacturing Energy Consumption Survey (MECS) to calibrate energy consumption to end-use energy categories: boilers, process heating...

  11. Coal industry annual 1997

    SciTech Connect (OSTI)

    NONE

    1998-12-01T23:59:59.000Z

    Coal Industry Annual 1997 provides comprehensive information about US coal production, number of mines, prices, productivity, employment, productive capacity, and recoverable reserves. US Coal production for 1997 and previous years is based on the annual survey EIA-7A, Coal Production Report. This report presents data on coal consumption, coal distribution, coal stocks, coal prices, and coal quality for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States. This report includes a national total coal consumption for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. 14 figs., 145 tabs.

  12. Coal industry annual 1993

    SciTech Connect (OSTI)

    Not Available

    1994-12-06T23:59:59.000Z

    Coal Industry Annual 1993 replaces the publication Coal Production (DOE/FIA-0125). This report presents additional tables and expanded versions of tables previously presented in Coal Production, including production, number of mines, Productivity, employment, productive capacity, and recoverable reserves. This report also presents data on coal consumption, coal distribution, coal stocks, coal prices, coal quality, and emissions for a wide audience including the Congress, Federal and State agencies, the coal industry, and the general public. In addition, Appendix A contains a compilation of coal statistics for the major coal-producing States. This report does not include coal consumption data for nonutility Power Producers who are not in the manufacturing, agriculture, mining, construction, or commercial sectors. This consumption is estimated to be 5 million short tons in 1993.

  13. Recycled brake linings as partial aggregate substitute in asphalt paving. Construction and final report. Report for July 1992-August 1996

    SciTech Connect (OSTI)

    Miller, P.A.; Sukley, R.

    1996-09-01T23:59:59.000Z

    The purpose of this project was to evaluate the performance of asphalt containing various percentages of brake lining as an aggregate, and compare its performance to that of normal asphalt containing natural aggregate. This project is an effort to explore alternate ways to use waste product. Four test section of FB-2 Modified mix containing brake lining materials were placed in July 1992 along with one control section on SR 3022 in Mercer county. To date all sections are performing satisfactory, and Brake linings should be recommended as a viable partial replacement of aggregate in bituminous materials. This study only considered the performance of only off-spec brake linings, therefore, any performance data or enviromental effects of placement of used brake material should be addressed.

  14. Energy Sector Cybersecurity Framework Implementation Guidance

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    JANUARY 2015 ENERGY SECTOR CYBERSECURITY FRAMEWORK IMPLEMENTATION GUIDANCE U.S. DEPARTMENT OF ENERGY OFFICE OF ELECTRICITY DELIVERY AND ENERGY RELIABILITY Energy Sector...

  15. Federal Sector Renewable Energy Project Implementation: ""What...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Federal Sector Renewable Energy Project Implementation: ""What's Working and Why Federal Sector Renewable Energy Project Implementation: ""What's Working and Why Presentation by...

  16. Market study for direct utilization of geothermal resources by selected sectors of economy

    SciTech Connect (OSTI)

    Not Available

    1980-08-01T23:59:59.000Z

    A comprehensive analysis is presented of industrial markets potential for direct use of geothermal energy by a total of six industry sectors: food and kindred products; tobacco manufactures; textile mill products; lumber and wood products (except furniture); chemicals and allied products; and leather and leather products. A brief statement is presented regarding sectors of the economy and major manufacturing processes which can readily utilize direct geothermal energy. Previous studies on plant location determinants are summarized and appropriate empirical data provided on plant locations. Location determinants and potential for direct use of geothermal resources are presented. The data was gathered through interviews with 30 senior executives in the six sectors of economy selected for study. Probable locations of plants in geothermal resource areas and recommendations for geothermal resource marketing are presented. Appendix A presents factors which impact on industry location decisions. Appendix B presents industry executives interviewed during the course of this study. (MHR)

  17. Electrochemical assessment and service-life prediction of mechanically stabilized earth walls backfilled with crushed concrete and recycled asphalt pavement

    E-Print Network [OSTI]

    Esfeller, Michael Watts, Jr.

    2009-06-02T23:59:59.000Z

    Studies of Texas A&M University in partial fulfillment of the requirements for the degree of MASTER OF SCIENCE August 2006 Major Subject: Civil Engineering ELECTROCHEMICAL ASSESSMENT AND SERVICE-LIFE PREDICTION... OF MECHANICALLY STABILIZED EARTH WALLS BACKFILLED WITH CRUSHED CONCRETE AND RECYCLED ASPHALT PAVEMENT A Thesis by MICHAEL WATTS ESFELLER, JR. Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment...

  18. Interfuel Substitution and Energy Use in the UK Manufacturing Sector

    E-Print Network [OSTI]

    Steinbuks, Jevgenijs

    of the following reasons. First, studies based on the aggregate data fail to account for large di¤erences in technological requirements for fuel types used in speci?c industries. For ex- ample, most cement kilns today use coal and petroleum coke as primary fuels... in the manufacturing processes. Waverman (1992) pointed out that fuels used by industrial sectors for non-energy purposes, such as coking coal, petrochemical feedstocks, or lubricants, have few available substitutes, and should therefore be excluded from the data...

  19. Welfare Impacts of Electricity Generation Sector Reform in the Philippines

    E-Print Network [OSTI]

    Toba, Natsuko

    2004-06-16T23:59:59.000Z

    -cost-benefit-analysis (SCBA) basically designs a behavioural and cost model of an industry and simulates it over the post privatization period with and without the sundry changes attributed to the privatization. Thus a counterfactual scenario (viz., enterprise without... ownership regime and those from the private sector participation/ownership. 4. The SCBA Methodology Galal, et al. (1994) identify three main groups in society, viz., consumers, private producers, and government as their framework in assessing...

  20. Energy-economy interactions revisited within a comprehensive sectoral model

    SciTech Connect (OSTI)

    Hanson, D. A.; Laitner, J. A.

    2000-07-24T23:59:59.000Z

    This paper describes a computable general equilibrium (CGE) model with considerable sector and technology detail, the ``All Modular Industry Growth Assessment'' Model (AMIGA). It is argued that a detailed model is important to capture and understand the several rolls that energy plays within the economy. Fundamental consumer and industrial demands are for the services from energy; hence, energy demand is a derived demand based on the need for heating, cooling mechanical, electrical, and transportation services. Technologies that provide energy-services more efficiently (on a life cycle basis), when adopted, result in increased future output of the economy and higher paths of household consumption. The AMIGA model can examine the effects on energy use and economic output of increases in energy prices (e.g., a carbon charge) and other incentive-based policies or energy-efficiency programs. Energy sectors and sub-sector activities included in the model involve energy extraction conversion and transportation. There are business opportunities to produce energy-efficient goods (i.e., appliances, control systems, buildings, automobiles, clean electricity). These activities are represented in the model by characterizing their likely production processes (e.g., lighter weight motor vehicles). Also, multiple industrial processes can produce the same output but with different technologies and inputs. Secondary recovery, i.e., recycling processes, are examples of these multiple processes. Combined heat and power (CHP) is also represented for energy-intensive industries. Other modules represent residential and commercial building technologies to supply energy services. All sectors of the economy command real resources (capital services and labor).

  1. Expanding the Industrial Assessment Center Program: Building an Industrial Efficiency Workforce

    E-Print Network [OSTI]

    Trombley, D.; Elliott, R. N.; Chittum, A.

    Expanding the Industrial Assessment Center Program: Building an Industrial Efficiency Workforce Daniel Trombley Engineering Associate R. Neal Elliott, Ph.D., P.E. Associate Director of Research American Council for an Energy-Efficient... of access to technical information and trained workforce. One of the most successful programs for achieving energy efficiency savings in the manufacturing sector is the US Department of Energy (DOE)'s Industrial Assessment Center (IAC) program...

  2. "Greening" Industrial Steam Generation via On-demand Steam Systems 

    E-Print Network [OSTI]

    Smith, J. P.

    2010-01-01T23:59:59.000Z

    Both recent economic and environmental conditions in the U.S. have converged to bring about unprecedented attention to energy efficiency and sustainability in the country's industrial sector. Historically, energy costs in ...

  3. Charting a Path to Net Zero Energy: Public-Private Sector Perspectives of the Commercial Buildings Consortium 

    E-Print Network [OSTI]

    Harris, J.

    2011-01-01T23:59:59.000Z

    Transforming the commercial buildings market to become "net-zero-energy-capable" will require dramatically lower levels of energy use sector wide. A comprehensive and concerted industry effort, partnering with utilities and government, must...

  4. Charting a Path to Net Zero Energy: Public-Private Sector Perspectives of the Commercial Buildings Consortium

    E-Print Network [OSTI]

    Harris, J.

    2011-01-01T23:59:59.000Z

    Transforming the commercial buildings market to become "net-zero-energy-capable" will require dramatically lower levels of energy use sector wide. A comprehensive and concerted industry effort, partnering with utilities and government, must...

  5. Energy Use in China: Sectoral Trends and Future Outlook

    E-Print Network [OSTI]

    2008-01-01T23:59:59.000Z

    nuclear Historical Primary Energy Consumption by sector Energy Use by Sector (EJ Services Transportation Agriculture

  6. The Office of Industrial Technologies technical reports

    SciTech Connect (OSTI)

    Not Available

    1992-01-01T23:59:59.000Z

    The US Department of Energy's Office of Industrial Technologies (OIT) conducts R D activities which focus on the objectives of improving energy efficiency and providing for fuel flexibility within US industry in the area of industrial energy conservation. The Office also conducts programs to reduce waste generation, increase recycling efforts, and improve the use of wastes as process feedstocks. An active program of technology transfer and education supports these activities and encourages adoption of new technologies. To accomplish these objectives OIT cooperates with the private sector to identify its technological needs and to share R D efforts. R D is conducted to the point that a new technology is shown to work and that it can be transferred to the private sector end-users. This bibliography contains information on all scientific and technical reports sponsored by the DOE Industrial Energy Conservation Program during the years 1988--1990.

  7. Energy Sector Vulnerability to Climate Change: Adaptation Options to Increase Resilience (Presentation)

    SciTech Connect (OSTI)

    Newmark, R. L.; Bilello, D.; Macknick, J.; Hallet, K. C.; Anderson, R.; Tidwell, V.; Zamuda, C.

    2013-02-01T23:59:59.000Z

    The U.S. Department of Energy is conducting an assessment of vulnerabilities of the U.S. energy sector to climate change and extreme weather. Emphasizing peer reviewed research, it seeks to quantify vulnerabilities and identify specific knowledge or technology gaps. It draws upon a July 2012 workshop, ?Climate Change and Extreme Weather Vulnerability Assessment of the US Energy Sector?, hosted by the Atlantic Council and sponsored by DOE to solicit industry input.

  8. Value-added utilisation of recycled concrete in hot-mix asphalt

    SciTech Connect (OSTI)

    Wong, Yiik Diew [School of Civil and Environmental Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore 639798 (Singapore); Sun, Darren Delai [School of Civil and Environmental Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore 639798 (Singapore)]. E-mail: ddsun@ntu.edu.sg; Lai, Dickson [School of Civil and Environmental Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore 639798 (Singapore)

    2007-07-01T23:59:59.000Z

    The feasibility of partial substitution of granite aggregate in hot-mix asphalt (HMA) with waste concrete aggregate was investigated. Three hybrid HMA mixes incorporating substitutions of granite fillers/fines with 6%, 45% untreated, and 45% heat-treated concrete were evaluated by the Marshall mix design method; the optimum binder contents were found to be 5.3%, 6.5% and 7.0% of grade Pen 60/70 bitumen, respectively. All three hybrid mixes satisfied the Marshall criteria of the Singapore Land Transport Authority (LTA) W3B wearing course specification. The hybrid mix with 6% concrete fillers gave comparable resilient modulus and creep resistance as the conventional W3B mix, while hybrid mixes with higher concrete substitutions achieved better performance. X-ray diffraction (XRD) showed the distinct presence of free lime in the heat-treated concrete, while the scanning electron microscope (SEM) provided an in-depth perspective of the concrete grains in the HMA matrix. The results suggest feasible use of waste concrete as partial aggregate substitution in HMA.

  9. Gasification world database 2007. Current industry status

    SciTech Connect (OSTI)

    NONE

    2007-10-15T23:59:59.000Z

    Information on trends and drivers affecting the growth of the gasification industry is provided based on information in the USDOE NETL world gasification database (available on the www.netl.doe.gov website). Sectors cover syngas production in 2007, growth planned through 2010, recent industry changes, and beyond 2010 - strong growth anticipated in the United States. A list of gasification-based power plant projects, coal-to-liquid projects and coal-to-SNG projects under consideration in the USA is given.

  10. Emerging Opportunities in Industrial Electrification Technologies 

    E-Print Network [OSTI]

    Schmidt, P. S.

    1989-01-01T23:59:59.000Z

    in the manufacturing sector. Nearly half of manufacturing energy use was in the process industries, which include chemicals, petroleum products, pulp and paper, foods, textiles, and tobacco. Metals production, primarily aluminum and steel, accounted for about 21... %, and metals fabrication, including transportation, machinery, instrumentation and electronics, and other metal products, about 19%. The balance of about 14% was used in other non-metals industries, such as stone, clay, and glass, rubber and plastics...

  11. Industrial Demand-Side Management in Texas

    E-Print Network [OSTI]

    Jaussaud, D.

    of programs result in lower consumption and/or lower peak demand, and ultimately reduce the need to build new capacity. Hence demand-side management can be used as a resource option to be considered alongside more traditional supply-side resources in a...INDUSTRIAL DEMAND-SIDE MANAGEMENT IN TEXAS Danielle Jaussaud Economic Analysis Section Public Utility Commission of Texas Austin, Texas ABSTRACT The industrial sector in Texas is highly energy intensive and represents a large share...

  12. Sector 1 Frequently Asked Questions

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Information Sector 1 Safety Plan (pdf) Useful X-Ray Related Numbers Si a0 5.4308 Angstrom CeO2 a05.411 Angstrom Cd-109 gamma 88.036 keV X-ray energywavelength conversion...

  13. A study of substitution solvents in asphalt fume extraction and the effects of heating duration and temperature

    E-Print Network [OSTI]

    Curry, Noel Thomas

    1981-01-01T23:59:59.000Z

    (denoted Dl). Duration two ( D2) ran from time 60 minutes to time 90 minutes, Dl and DZ were separated by a 30 minute period in wh i ch no sampling occurred. The total time of heati ng at this temperature range was 90 minutes, which was near the limit... of the filter to hold it in position, and the cassette cap was placed on top of this. 3oth ends were then plugged. (Figure 2) After a warming period of approximately 30 minutes, the temperature of the liquid asphalt was raised to 250 C. iihen it reached...

  14. Current and future industrial energy service characterizations

    SciTech Connect (OSTI)

    Krawiec, F.; Thomas, T.; Jackson, F.; Limaye, D.R.; Isser, S.; Karnofsky, K.; Davis, T.D.

    1980-10-01T23:59:59.000Z

    Current and future energy demands, end uses, and cost used to characterize typical applications and resultant services in the industrial sector of the United States and 15 selected states are examined. A review and evaluation of existing industrial energy data bases was undertaken to assess their potential for supporting SERI research on: (1) market suitability analysis, (2) market development, (3) end-use matching, (3) industrial applications case studies, and (4) identification of cost and performance goals for solar systems and typical information requirements for industrial energy end use. In reviewing existing industrial energy data bases, the level of detail, disaggregation, and primary sources of information were examined. The focus was on fuels and electric energy used for heat and power purchased by the manufacturing subsector and listed by 2-, 3-, and 4-digit SIC, primary fuel, and end use. Projections of state level energy prices to 1990 are developed using the energy intensity approach. The effects of federal and state industrial energy conservation programs on future industrial sector demands were assessed. Future end-use energy requirements were developed for each 4-digit SIC industry and were grouped as follows: (1) hot water, (2) steam (212 to 300/sup 0/F, each 100/sup 0/F interval from 300 to 1000/sup 0/F, and greater than 1000/sup 0/F), and (3) hot air (100/sup 0/F intervals). Volume I details the activities performed in this effort.

  15. Climate VISION: Private Sector Initiatives: Cement: Resources...

    Office of Scientific and Technical Information (OSTI)

    FederalState Programs DOE Industrial Materials of the Future Industrial Materials for the Future (IMF) is a crosscutting activity of the Industrial Technologies Program. The...

  16. Water Impacts of the Electricity Sector (Presentation)

    SciTech Connect (OSTI)

    Macknick, J.

    2012-06-01T23:59:59.000Z

    This presentation discusses the water impacts of the electricity sector. Nationally, the electricity sector is a major end-user of water. Water issues affect power plants throughout the nation.

  17. Biomass Resources for the Federal Sector

    SciTech Connect (OSTI)

    Not Available

    2005-08-01T23:59:59.000Z

    Biomass Resources for the Federal Sector is a fact sheet that explains how biomass resources can be incorporated into the federal sector, and also how they can provide opportunities to meet federal renewable energy goals.

  18. Advanced Vehicle Electrification and Transportation Sector Electrifica...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Advanced Vehicle Electrification and Transportation Sector Electrification Plug-in Hybrid (PHEV) Vehicle Technology Advancement and Demonstration Activity Advanced Vehicle...

  19. Energy efficiency programs and policies in the industrial sector in industrialized countries

    E-Print Network [OSTI]

    Galitsky, Christina; Price, Lynn; Worrell, Ernst

    2004-01-01T23:59:59.000Z

    23. Wisconsin – Focus on Energy website: http://pageId =4 24. International Energy Agency (IEA) documents:index.html 16. Renewable Energy Equity Fund (REEF) website:

  20. Energy efficiency programs and policies in the industrial sector in industrialized countries

    E-Print Network [OSTI]

    Galitsky, Christina; Price, Lynn; Worrell, Ernst

    2004-01-01T23:59:59.000Z

    sustainable energy system was begun, further supporting those goals of increased renewable energy sources and energy efficiency. Sweden

  1. Garnering the Industrial Sector: A Comparison of Cutting Edge Industrial DSM Programs

    E-Print Network [OSTI]

    Kyricopoulos, P. F.; Wikler, G. A.; Faruqui, A.; Wood, B. G.

    ~ p~oduct quality! greater relIability, or facl1ltatlOn of long-term environmental compliance. ? Minimizing risk. Changing production procedures is a risk. Customers are lookin f for proven technologies and procedures that e$ure smooth...

  2. Industrial Energy Efficiency: Designing Effective State Programs for the Industrial Sector

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the.pdfBreaking of BlytheDepartment of EnergyTreatment andJuneJobs |

  3. Industrial Energy Efficiency: Designing Effective State Programs for the Industrial Sector: Executive Summary

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the.pdfBreaking of BlytheDepartment of EnergyTreatment andJuneJobs |Executive Summary

  4. A novel technique for the production of cool colored concrete tile and asphalt shingle roofing products

    SciTech Connect (OSTI)

    Levinson, Ronnen; Akbari, Hashem; Berdahl, Paul; Wood, Kurt; Skilton, Wayne; Petersheim, Jerry

    2009-11-20T23:59:59.000Z

    The widespread use of solar-reflective roofing materials can save energy, mitigate urban heat islands and slow global warming by cooling the roughly 20% of the urban surface that is roofed. In this study we created prototype solar-reflective nonwhite concrete tile and asphalt shingle roofing materials using a two-layer spray coating process intended to maximize both solar reflectance and factory-line throughput. Each layer is a thin, quick-drying, pigmented latex paint based on either acrylic or a poly(vinylidene fluoride)/acrylic blend. The first layer is a titanium dioxide rutile white basecoat that increases the solar reflectance of a gray-cement concrete tile from 0.18 to 0.79, and that of a shingle surfaced with bare granules from 0.06 to 0.62. The second layer is a 'cool' color topcoat with weak near-infrared (NIR) absorption and/or strong NIR backscattering. Each layer dries within seconds, potentially allowing a factory line to pass first under the white spray, then under the color spray. We combined a white basecoat with monocolor topcoats in various shades of red, brown, green and blue to prepare 24 cool color prototype tiles and 24 cool color prototypes shingles. The solar reflectances of the tiles ranged from 0.26 (dark brown; CIELAB lightness value L* = 29) to 0.57 (light green; L* = 76); those of the shingles ranged from 0.18 (dark brown; L* = 26) to 0.34 (light green; L* = 68). Over half of the tiles had a solar reflectance of at least 0.40, and over half of the shingles had a solar reflectance of at least 0.25.

  5. Sectoral trends in global energy use and greenhouse gas emissions

    E-Print Network [OSTI]

    2006-01-01T23:59:59.000Z

    in Building Sector Electricity Consumption parameterin Building Sector Electricity Consumption Appendix 1. WorldElectricity in Building Sector Electricity Consumption iii

  6. Power Politics: The Political Economy of Russia's Electricity Sector Liberalization

    E-Print Network [OSTI]

    Wengle, Susanne Alice

    2010-01-01T23:59:59.000Z

    Private Participation in the Electricity Sector World BankTelecommunications and Electricity Sectors." Governance 19,41 with journalist covering electricity sector, Vladivostok,

  7. Smart Grids: Sectores y actividades clave | 1 Smart Grids: Sectores y actividades clave

    E-Print Network [OSTI]

    Politècnica de Catalunya, Universitat

    Smart Grids: Sectores y actividades clave | 1 Smart Grids: Sectores y actividades clave INFORME para la Sostenibilidad Energética y Ambiental, FUNSEAM. #12;Smart Grids: Sectores y actividades clave eléctrica y los diferentes sectores que forman la smart grid. 6 Figura 2. Evolución y previsión de

  8. Asphaltenes and Asphalts, 2. Developments in Petroleum Science, 40 B edited by T.F. Yen and G.V. Chilingarian

    E-Print Network [OSTI]

    Ã?agin, Tahir

    Asphaltenes and Asphalts, 2. Developments in Petroleum Science, 40 B edited by T.F. Yen and G OF ASPHALTENES: A PREDICTIVE APPROACH BASED ON COMPUTER ASSISTED STRUCTURE ELUCIDATION AND ATOMISTIC SIMULATIONS, asphaltenes and resins [1­4]. Asphaltenes are operationally defined as the non-volatile and polar fraction

  9. Financial Sector Ups and Downs and the Real Sector: Up by the Stairs and Down by the Parachute

    E-Print Network [OSTI]

    Aizenman, Joshua; Pinto, Brian; Sushko, Vladyslav

    2012-01-01T23:59:59.000Z

    May 2012 Financial Sector Ups and Downs and the Real Sector:to reclassifying financial sector ups and downs as turning

  10. The Changing US Electric Sector Business Model

    E-Print Network [OSTI]

    Aliff, G.

    2013-01-01T23:59:59.000Z

    The Changing US Electric Sector Business Model CATEE 2013 Clean Air Through Energy Efficiency Conference San Antonio, Texas December 17, 2013 ESL-KT-13-12-57 CATEE 2013: Clean Air Through Energy Efficiency Conference, San Antonio, Texas Dec. 16...-18 Copyright © 2013 Deloitte Development LLC. All rights reserved. • Fundamentals of the US Electric Sector Business Model • Today’s Challenges Faced by U.S. Electric Sector • The Math Does Not Lie: A Look into the Sector’s Future • Disruption to Today...

  11. Changing Trends in the Bulk Chemicals and Pulp and Paper Industries (released in AEO2005)

    Reports and Publications (EIA)

    2005-01-01T23:59:59.000Z

    Compared with the experience of the 1990s, rising energy prices in recent years have led to questions about expectations of growth in industrial output, particularly in energy-intensive industries. Given the higher price trends, a review of expected growth trends in selected industries was undertaken as part of the production of Annual Energy Outlook 2005 (AEO). In addition, projections for the industrial value of shipments, which were based on the Standard Industrial Classification (SIC) system in AEO2004, are based on the North American Industry Classification System (NAICS) in AEO2005. The change in industrial classification leads to lower historical growth rates for many industrial sectors. The impacts of these two changes are highlighted in this section for two of the largest energy-consuming industries in the U.S. industrial sector-bulk chemicals and pulp and paper.

  12. User:GregZiebold/Sector test | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov YouKizildere IRaghuraji Agro IndustriesTown of Ladoga,planning methodologies and tools | Open EnergyCalpakGatewaySector

  13. Cross-sector Demand Response

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville Power Administration would likeConstitution4 Department of EnergyCross-Sector Sign In About |

  14. External research and energy efficiency in the process industries

    SciTech Connect (OSTI)

    Kaarsberg, T.M.; Foust, T.D.

    1997-07-01T23:59:59.000Z

    The process industries in the US are under enormous pressure. These industries, even more than US industry on average, face skyrocketing environmental costs, a rapidly changing electricity market, potential climate change policies, aging infrastructure and strong international competition. To be profitable they must reduce their costs and environmental impacts while increasing their product quality, turnaround time, productivity and output. Most of these industries have already cut costs and labor as much as possible. Therefore, to survive, these industries must innovate. History shows that industries that are the most innovative are the most successful. These industries are vital to the US economy. For example, the metals, pulp and paper, chemicals and the petroleum refining industries account for more than $800 billion in products shipped and employ more than three million workers. Although the US has shifted dramatically toward services with 77% of workers and 74% of GDP now in the service sector, what many have missed is that the process industries are important customers for many of these new services. ServOnly the last two years of NSF industrial R and D data provide any breakout of non-manufacturing R and D. This paper discusses the past, current and possible future role of eternal research and development (R and D)--much of which is now in the service sector--in fostering innovation and thus energy efficiency in these industries. The authors suggest that these industries are more innovative than previously thought because of external research.

  15. Industrial ecology Prosperity Game{trademark}

    SciTech Connect (OSTI)

    Beck, D.; Boyack, K.; Berman, M.

    1998-03-01T23:59:59.000Z

    Industrial ecology (IE) is an emerging scientific field that views industrial activities and the environment as an interactive whole. The IE approach simultaneously optimizes activities with respect to cost, performance, and environmental impact. Industrial Ecology provides a dynamic systems-based framework that enables management of human activity on a sustainable basis by: minimizing energy and materials usage; insuring acceptable quality of life for people; minimizing the ecological impact of human activity to levels that natural systems can sustain; and maintaining the economic viability of systems for industry, trade and commerce. Industrial ecology applies systems science to industrial systems, defining the system boundary to incorporate the natural world. Its overall goal is to optimize industrial activities within the constraints imposed by ecological viability, globally and locally. In this context, Industrial systems applies not just to private sector manufacturing and services but also to government operations, including provision of infrastructure. Sandia conducted its seventeenth Prosperity Game{trademark} on May 23--25, 1997, at the Hyatt Dulles Hotel in Herndon, Virginia. The primary sponsors of the event were Sandia National Laboratories and Los Alamos National Laboratory, who were interested in using the format of a Prosperity Game to address some of the issues surrounding Industrial Ecology. Honorary game sponsors were: The National Science Foundation; the Committee on Environmental Improvement, American Chemical Society; the Industrial and Engineering Chemistry Division, American Chemical Society; the US EPA--The Smart Growth Network, Office of Policy Development; and the US DOE-Center of Excellence for Sustainable Development.

  16. Power Politics: The Political Economy of Russia's Electricity Sector Liberalization

    E-Print Network [OSTI]

    Wengle, Susanne Alice

    2010-01-01T23:59:59.000Z

    Electricity Sector in Russia: Regional Aspects " In Economics EducationElectricity Sector in Russia: Regional Aspects " in Economics Education

  17. INDUST: An Industrial Data Base

    E-Print Network [OSTI]

    Wilfert, G. L.; Moore, N. L.

    .5% of the natural gas consump tion, 98.1% of the fuel oil consumption, 99.2% of the coal/coke consumption, and 99.7% of a class of fuels called "other" fuels. Within these 13 indus try groups, INDUST addresses a wide variety of energy-intense industries... the manufac turing sector, Table 1 shows the latest EIA pro visional estimate of energy consumption (in trillion Btu) for 1985. The EIA reports fuel consumption according to five categories: electricity, fuel oil, natural gas, coal and coke, and other...

  18. Shrenik Industries | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnual Siteof Energy 2,AUDITCalifornia Sector:Shrenik Industries Jump to: navigation, search

  19. Ventower Industries | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnual Siteof Energy 2,AUDITCalifornia Sector:ShreniksourceVentower Industries Jump to:

  20. Macroscopic theory of dark sector

    E-Print Network [OSTI]

    Boris E. Meierovich

    2014-10-06T23:59:59.000Z

    A simple Lagrangian with squared covariant divergence of a vector field as a kinetic term turned out an adequate tool for macroscopic description of the dark sector. The zero-mass field acts as the dark energy. Its energy-momentum tensor is a simple additive to the cosmological constant. Massive fields {\\phi}_{I} with {\\phi}^{K}{\\phi}_{K}0 describe two different forms of dark matter. The space-like ({\\phi}^{K}{\\phi}_{K}0) massive field displays repulsive elasticity. In balance with dark energy and ordinary matter it provides a four parametric diversity of regular solutions of the Einstein equations describing different possible cosmological and oscillating non-singular scenarios of evolution of the universe. In particular, the singular big bang turns into a regular inflation-like transition from contraction to expansion with the accelerate expansion at late times. The fine-tuned Friedman-Robertson-Walker singular solution is a particular limiting case at the boundary of existence of regular oscillating solutions in the absence of vector fields. The simplicity of the general covariant expression for the energy-momentum tensor allows to display the main properties of the dark sector analytically and avoid unnecessary model assumptions.

  1. Hybrid modeling of industrial energy consumption and greenhouse gas emissions with an application to Canada

    E-Print Network [OSTI]

    implemented in Canada, what would be the response of the industrial sector in terms of energy consumptionHybrid modeling of industrial energy consumption and greenhouse gas emissions with an application for modeling industrial energy consumption, among them a series of environmental and security externalities

  2. Crossing innovation & product projects management: A comparative analysis in automotive industry

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    1 Crossing innovation & product projects management: A comparative analysis in automotive industry in automotive industry INTRODUCTION Projectification and platform approaches have been two main transformation in the automotive industry. This sector provides an interesting empirical opportunity to study this question, since

  3. The impact on photovoltaic worth of utulity rate and reform and of specific market, financial, and policy variables : a commercialindustrialinstitution sector analysis

    E-Print Network [OSTI]

    Dinwoodie, Thomas L.

    1980-01-01T23:59:59.000Z

    This work provides an assessment of the economic outlook for photovoltaic systems in the commercial, industrial and institutional sectors in the year 1986. We first summarize the expected cost and performance goals for ...

  4. Examination of the factors and issues for an environmental technology utilization partnership between the private sector and the Department of Energy. Final report

    SciTech Connect (OSTI)

    Brouse, P.

    1997-05-01T23:59:59.000Z

    The Department of Energy (DOE) held a meeting on November 12, 1992 to evaluate the DOE relations with industry and university partners concerning environmental technology utilization. The goal of this meeting was to receive feedback from DOE industry and university partners for the identification of opportunities to improve the DOE cooperative work processes with the private sector. The meeting was designed to collect information and to turn that information into action to improve private sector partnerships with DOE.

  5. MIT and Automotive Industries MIT Industry Brief

    E-Print Network [OSTI]

    Ceder, Gerbrand

    MIT and Automotive Industries MIT Industry Brief MIT's Industrial Liaison Program (ILP) can bring@ilp.mit.edu, or visit http://ilp-www.mit.edu. MIT and Automotive Industries The Massachusetts Institute of Technology (MIT) is a leading center of research and education on topics important to the automotive industry

  6. Public Sector New Construction and Retrofit Program

    Broader source: Energy.gov [DOE]

    The Illinois Department of Commerce and Economic Opportunity (DCEO) Bureau of Energy and Recycling administers the public sector energy efficiency programs required by the Illinois Energy...

  7. Public Sector Energy Efficiency Aggregation Program

    Broader source: Energy.gov [DOE]

    The Illinois Department of Commerce and Economic Opportunity (DCEO) administers the Illinois Energy Now programs, including the Public Sector Energy Efficiency Aggregation Program. The program will...

  8. Accelerating Investments in the Geothermal Sector, Indonesia...

    Open Energy Info (EERE)

    in the Geothermal Sector, Indonesia (Presentation) Jump to: navigation, search OpenEI Reference LibraryAdd to library Conference Paper: Accelerating Investments in the Geothermal...

  9. Energy Sector Cybersecurity Framework Implementation Guidance...

    Broader source: Energy.gov (indexed) [DOE]

    Technology (NIST) released a Cybersecurity Framework. DOE has collaborated with private sector stakeholders through the Electricity Subsector Coordinating Council (ESCC) and the...

  10. Draft Energy Sector Cybersecurity Framework Implementation Guidance...

    Broader source: Energy.gov (indexed) [DOE]

    Technology (NIST) released a Cybersecurity Framework. DOE has collaborated with private sector stakeholders through the Electricity Subsector Coordinating Council (ESCC) and the...

  11. Climate VISION: Private Sector Initiatives: Business Roundtable...

    Office of Scientific and Technical Information (OSTI)

    Results Every Sector, One RESOLVE: A Progress Report on Business Roundtable's Climate RESOLVE Program, September 2004 (PDF 1.8 MB) Download Acrobat Reader...

  12. Transforming Federal sector procurement of performance based energy services

    SciTech Connect (OSTI)

    Dahle, D.E.

    1998-07-01T23:59:59.000Z

    Federal agencies are mandated to reduce their energy use by 30% by 2005. The investment in energy projects required to achieve this reduction is estimated at $4 billion to $6 billion. The Department of Energy's (DOE's) Federal Energy Management Program (FEMP) has developed streamlined procurement vehicles to allow Federal agencies to acquire private-sector-financed, performance-based energy services for all Federal buildings. These procurement vehicles, called Super Energy Savings Performance Contracts (Super ESPCs) will be in place covering all regions of the US by summer 1998. The six regional DOE ESPC contracts will provide agencies the ability to contract for up to $4.5 billion in private sector financed energy services. This represents an estimated potential of $3 billion in private sector investments in Federal buildings for energy efficiency, renewable energy and water conservation projects. DOE has developed guidelines and unique project development tools that will allow Federal agencies to contract for ESPC services in months rather than in the years it used to take to develop and implement site specific ESPC projects. The Federal government's buying power has transformed the energy services and utilities industries by stimulating the formation of new cross-industry teams and partnerships to meet the breadth of capability and ability to respond to the needs of Federal facilities in large geographic regions. This paper presents results to date and describes the linkages between the Super ESPC Program and the US Climate Change Proposal. A key US strategy that calls for Federal leadership, and in particular for DOE to spearhead a comprehensive effort to reduce greenhouse gas emissions from Federal sources.

  13. The Department of Energy's Solar Industrial Program: New ideas for American industry

    SciTech Connect (OSTI)

    Anderson, J.V.; Hauser, S.G.; Clyne, R.J.

    1991-07-01T23:59:59.000Z

    As society becomes more and more sensitive to the environment, and energy supplies become more scarce, the application of solar energy is expanding into new areas. The industrial sector is one of the most difficult for solar energy to impact because of its technical diversity and economic requirements. However, the opportunities are still abundant. The Department of Energy's Solar Industrial Program is dedicated to advancing the applications of solar energy in this sector. Research and technology development activities are currently focused in three areas: solar process heat, advanced materials manufacturing, and destruction of chemical wastes. The Solar Energy Research Institute manages these activities for DOE with close interactions with other federal agencies, private industry, and universities. 7 figs.

  14. Utilize Cementitious High Carbon Fly Ash (CHCFA) to Stabilize Cold In-Place Recycled (CIR) Asphalt Pavement as Base Coarse

    SciTech Connect (OSTI)

    Wen, Haifang; Li, Xiaojun; Edil, Tuncer; O'Donnell, Jonathan; Danda, Swapna

    2011-02-05T23:59:59.000Z

    The purpose of this study was to evaluate the performance of cementitious high carbon fly ash (CHCFA) stabilized recycled asphalt pavement as a base course material in a real world setting. Three test road cells were built at MnROAD facility in Minnesota. These cells have the same asphalt surface layers, subbases, and subgrades, but three different base courses: conventional crushed aggregates, untreated recycled pavement materials (RPM), and CHCFA stabilized RPM materials. During and after the construction of the three cells, laboratory and field tests were carried out to characterize the material properties. The test results were used in the mechanistic-empirical pavement design guide (MEPDG) to predict the pavement performance. Based on the performance prediction, the life cycle analyses of cost, energy consumption, and greenhouse gasses were performed. The leaching impacts of these three types of base materials were compared. The laboratory and field tests showed that fly ash stabilized RPM had higher modulus than crushed aggregate and RPM did. Based on the MEPDG performance prediction, the service life of the Cell 79 containing fly ash stabilized RPM, is 23.5 years, which is about twice the service life (11 years) of the Cell 77 with RPM base, and about three times the service life (7.5 years) of the Cell 78 with crushed aggregate base. The life cycle analysis indicated that the usage of the fly ash stabilized RPM as the base of the flexible pavement can significantly reduce the life cycle cost, the energy consumption, the greenhouse gases emission. Concentrations of many trace elements, particularly those with relatively low water quality standards, diminish over time as water flows through the pavement profile. For many elements, concentrations below US water drinking water quality standards are attained at the bottom of the pavement profile within 2-4 pore volumes of flow.

  15. Climate VISION: Private Sector Initiatives: Semiconductors: Work...

    Office of Scientific and Technical Information (OSTI)

    of EPA. The plan describes actions the industry intends to take to achieve its Climate VISION goal by 2010. Read the Semiconductor Industry Association Work Plan (PDF 94...

  16. Industrial Users

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItemResearch > The Energy Materials Center at CornellOf SmartIndustrial Users The

  17. Industry @ ALS

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742EnergyOnItemResearch > The Energy Materials Center at CornellOf SmartIndustrial Users

  18. Industrial Users

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of Science (SC) EnvironmentalGyroSolé(tm)HydrogenRFP »summerlectures [ICO]default Sign InIndustrial

  19. EU, CHINA AND THE ENVIRONMENTAL CHALLENGE IN AFRICA A case study from timber industry in Gabon

    E-Print Network [OSTI]

    1 EU, CHINA AND THE ENVIRONMENTAL CHALLENGE IN AFRICA A case study from timber industry: .....................................................................................................................................................2 Part I: The EU, China and the external environmental dimension....................................................................3 1.1 China as a competitor normative power in the environmental sector

  20. Sustainability Policy and Green Growth of the South Korean Construction Industry 

    E-Print Network [OSTI]

    Jeong, Hwayeon

    2011-10-21T23:59:59.000Z

    South Korea is among a host of countries trying to achieve sustainable development across whole industry sectors by adopting "Green Growth" as the vision of the national development in the Korean government. The government has executed a vast effort...

  1. New 3E Plus Computer Program- A Tool for Improving Industrial Energy Efficiency

    E-Print Network [OSTI]

    Brayman, N. J.

    The task of determining how much insulation is necessary in the US industrial and manufacturing sector to save money, use less energy, reduce plant emissions and improve process efficiency has been greatly simplified thanks to a software program...

  2. 'Tilted' Industrial Electric Rates: A New Negative Variable for Energy Engineers 

    E-Print Network [OSTI]

    Greenwood, R. W.

    1981-01-01T23:59:59.000Z

    The cost of purchased electricity for industry is rising even faster than for other sectors. Conventional means of reducing power costs include internal techniques like load management, demand controls and energy conservation. External mechanisms...

  3. The Public Utility and Industry: A Customer- Supplier Relationship for Long-Term Survival

    E-Print Network [OSTI]

    Janson, J. R.

    The entire country is undergoing a significant change in customer attitide toward services and products. This change is geared toward a quality service/ product for the least cost. Industry and the utility sector need to apply the aspects of quality...

  4. Modeling ruminant methane emissions from the U.S. beef cattle industry

    E-Print Network [OSTI]

    Turk, Danny Carroll

    1993-01-01T23:59:59.000Z

    Computer models were constructed to estimate methane emissions from cow/calf, replacement heifers, burs, stockers and feedlot sectors of the U.S. beef cattle industry. Methane (CH4) yields were calculated based on net energy values and forage...

  5. Technology partnerships: Enhancing the competitiveness, efficiency, and environmental quality of American industry

    SciTech Connect (OSTI)

    NONE

    1995-04-01T23:59:59.000Z

    An overview of the Department of Energy`s Office of Industrial Technologies and its private sector partnerships is presented. Commercial success stories and real-world benefits of the technology partnerships are discussed.

  6. National Electric Sector Cybersecurity Organization Resource (NESCOR)

    SciTech Connect (OSTI)

    None, None

    2014-06-30T23:59:59.000Z

    The goal of the National Electric Sector Cybersecurity Organization Resource (NESCOR) project was to address cyber security issues for the electric sector, particularly in the near and mid-term. The following table identifies the strategies from the DOE Roadmap to Achieve Energy Delivery Systems Cybersecurity published in September 2011 that are applicable to the NESCOR project.

  7. Institute of Public Sector Accounting Research

    E-Print Network [OSTI]

    Edinburgh, University of

    THE STATE" New Public Sector Seminar, Edinburgh, 6-7th November 2014 Co-Chairs: Liisa Kurunmaki, Irvine and consultants depend on in the management of public service organisations, and what is the statusInstitute of Public Sector Accounting Research I·P·S·A·R In Government, Public Services

  8. Managing Technical Risk: Understanding Private Sector

    E-Print Network [OSTI]

    action. Our study seeks to inform the decisions of both government managers and private entrepreneursApril 2000 Managing Technical Risk: Understanding Private Sector Decision Making on Early Stage 00-787 Managing Technical Risk Understanding Private Sector Decision Making on Early Stage Technology

  9. Pacific Rim Summit on Industrial Biotechnology & Bioenergy

    Broader source: Energy.gov [DOE]

    The ninth annual Pacific Rim Summit on Industrial Biotechnology and Bioenergy will be held from December 7–9, 2014, in San Diego, California, at the Westin Gaslamp Quarter. Bringing together representatives from various countries all around the Pacific Rim, this event will focus on the growth of the industrial biotechnology and bioenergy sectors in North America and the Asia-Pacific region. Glenn Doyle, BETO's Deployment & Demonstration Technology Manager, will be moderating and speaking at a session on entitled "Utilizing Strategic Partnerships to Grow Your Business" on December 9.

  10. Mechanical & Industrial Engineering

    E-Print Network [OSTI]

    Mountziaris, T. J.

    Mechanical & Industrial Engineering 1 Welcome MIE Industrial Advisory Board October 15, 2010 #12;Mechanical & Industrial Engineering 2 MIE Dorothy Adams Undergraduate/Graduate Secretary David Schmidt Associate Professor & Graduate Program Director #12;Mechanical & Industrial Engineering 3 MIE James Rinderle

  11. Industrial Decision Making 

    E-Print Network [OSTI]

    Elliott, R. N.; McKinney, V.; Shipley, A.

    2008-01-01T23:59:59.000Z

    and industrial investment decision-making. The paper will also address several important questions: • Why has industrial investment declined? • What is the outlook for industrial investment? • How can programs engage industry for future opportunities?...

  12. Surety of the nation`s critical infrastructures: The challenge restructuring poses to the telecommunications sector

    SciTech Connect (OSTI)

    Cox, R.; Drennen, T.E.; Gilliom, L.; Harris, D.L.; Kunsman, D.M.; Skroch, M.J.

    1998-04-01T23:59:59.000Z

    The telecommunications sector plays a pivotal role in the system of increasingly connected and interdependent networks that make up national infrastructure. An assessment of the probable structure and function of the bit-moving industry in the twenty-first century must include issues associated with the surety of telecommunications. The term surety, as used here, means confidence in the acceptable behavior of a system in both intended and unintended circumstances. This paper outlines various engineering approaches to surety in systems, generally, and in the telecommunications infrastructure, specifically. It uses the experience and expectations of the telecommunications system of the US as an example of the global challenges. The paper examines the principal factors underlying the change to more distributed systems in this sector, assesses surety issues associated with these changes, and suggests several possible strategies for mitigation. It also studies the ramifications of what could happen if this sector became a target for those seeking to compromise a nation`s security and economic well being. Experts in this area generally agree that the U. S. telecommunications sector will eventually respond in a way that meets market demands for surety. Questions remain open, however, about confidence in the telecommunications sector and the nation`s infrastructure during unintended circumstances--such as those posed by information warfare or by cascading software failures. Resolution of these questions is complicated by the lack of clear accountability of the private and the public sectors for the surety of telecommunications.

  13. Rutting Performance of Airport Hot-Mix Asphalt Characterized by Laboratory Performance Testing, Full-Scale Accelerated Pavement Testing, and Finite Element Modeling

    E-Print Network [OSTI]

    Rushing, John Ford

    2014-04-25T23:59:59.000Z

    California Bearing Ratio DoD Department of Defense DSR Dynamic Shear Rheometer ERDC U.S. Army Engineer Research and Development Center FAA Federal Aviation Administration FN flow number FT flow time HMA Hot Mix Asphalt HVS heavy vehicle simulator... aircraft continue to necessitate modifications in the procedures by which HMA mixtures are designed so that rutting does not become a prevalent distress on airport pavements. The Federal Aviation Administration (FAA) has predominantly required use...

  14. INDUSTRIAL ENGINEERING Industrial engineering is concerned

    E-Print Network [OSTI]

    INDUSTRIAL ENGINEERING Industrial engineering is concerned with looking at the "big picture" of systems that allow organizations and individuals to perform at their best. Industrial engineers bridge should be used and how they should be used. The focus of industrial engineering is on process improvement

  15. INDUSTRIAL ENGINEERING Industrial engineering is concerned

    E-Print Network [OSTI]

    INDUSTRIAL ENGINEERING Industrial engineering is concerned with looking at the "big picture" of systems that allow organizations and individuals to perform at their best. Industrial engineers bridge should be used and how they should be used. Industrial engineers design and run the factories and systems

  16. Advanced technology options for industrial heating equipment research

    SciTech Connect (OSTI)

    Jain, R.C.

    1992-10-01T23:59:59.000Z

    This document presents a strategy for a comprehensive program plan that is applicable to the Combustion Equipment Program of the DOE Office of Industrial Technologies (the program). The program seeks to develop improved heating equipment and advanced control techniques which, by improvements in combustion and beat transfer, will increase energy-use efficiency and productivity in industrial processes and allow the preferred use of abundant, low grade and waste domestic fuels. While the plan development strategy endeavors to be consistent with the programmatic goals and policies of the office, it is primarily governed by the needs and concerns of the US heating equipment industry. The program, by nature, focuses on energy intensive industrial processes. According to the DOE Manufacturing Energy Consumption Survey (MECS), the industrial sector in the US consumed about 21 quads of energy in 1988 in the form of coal, petroleum, natural gas and electricity. This energy was used as fuels for industrial boilers and furnaces, for agricultural uses, for construction, as feedstocks for chemicals and plastics, and for steel, mining, motors, engines and other industrial use over 75 percent of this energy was consumed to provide heat and power for manufacturing industries. The largest consumers of fuel energy were the primary metals, chemical and allied products, paper and allied products, and stone, clay and glass industry groups which accounted for about 60% of the total fuel energy consumed by the US manufacturing sector.

  17. Photovoltaic industry progress through 1984

    SciTech Connect (OSTI)

    Watts, R.L.; Smith, S.A.; Dirks, J.A.

    1985-04-01T23:59:59.000Z

    The growth of the US photovoltaics (PV) industry over the past decade has been impressive. First designed to provide power for satellites using high-cost production techniques, PV is now the economical choice in many remote terrestrial applications. The remarkable growth of PV in terms of quality of cells and modules, production techniques, and system design, was initiated by a cooperative effort of the US Government and the domestic PV manufacturers. European and Japanese firms entered the PV industry later, but are also growing rapidy. The Europeans continue to supply PV systems for village electrification and water pumping to many Third World countries. The Japanese have been developing the amorphous silicon (A-Si) technology by expanding its use in consumer goods. The world PV industry saw dramatic changes in industry ownership and in the emphasis on developing new and improved technology during 1984. The objective of this report is to present information on the developments of the world PV industry and focuses on developments occurring in 1984. Information is presented on a regional basis (US, Europe, Japan, other) to avoid disclosing company-confidential data. All information was gleaned from several sources, including a review of the technical literature and direct contacts with PV manufacturers. Prior to publishing the regional totals, all numbers were compared with those of other sources. The information contained in this report is prepared for use by the Department of Energy for their use in long-term R and D planning. However, this information should also be of interest by PV manufacturers and to those who may be contemplating entering the PV market. PV shipments for 1984, government supports for PV, and various PV market sectors are discussed.

  18. Broadening Industry Governance to Include Nonproliferation

    SciTech Connect (OSTI)

    Hund, Gretchen; Seward, Amy M.

    2008-11-11T23:59:59.000Z

    As industry is the first line of defense in detecting and thwarting illicit trade networks, the engagement of the private sector is critical to any government effort to strengthen existing mechanisms to protect goods and services throughout the supply chain. This study builds on previous PNNL work to continue to evaluate means for greater industry engagement to complement and strengthen existing governmental efforts to detect and stem the trade of illicit goods and to protect and secure goods that could be used in making a weapon of mass destruction. Specifically, the study evaluates the concept of Industry Self Regulation, defined as a systematic voluntary program undertaken by an industry or by individual companies to anticipate, implement, supplement, or substitute for regulatory requirements in a given field, generally through the adoption of best practices. Through a series of interviews with companies with a past history of non-compliance, trade associations and NGOs, the authors identify gaps in the existing regulatory infrastructure, drivers for a self regulation approach and the form such an approach might take, as well as obstacles to be overcome. The authors conclude that it is at the intersection of industry, government, and security that—through collaborative means—the effectiveness of the international nonproliferation system—can be most effectively strengthened to the mutual benefit of both government and the private sector. Industry has a critical stake in the success of this regime, and has the potential to act as an integrating force that brings together the existing mechanisms of the global nonproliferation regime: export controls, physical protection, and safeguards. The authors conclude that industry compliance is not enough; rather, nonproliferation must become a central tenant of a company’s corporate culture and be viewed as an integral component of corporate social responsibility (CSR).

  19. Electricity sector restructuring and competition : lessons learned

    E-Print Network [OSTI]

    Joskow, Paul L.

    2003-01-01T23:59:59.000Z

    We now have over a decade of experience with the privatization, restructuring, regulatory reform, and wholesale and retail competition in electricity sectors around the world. The objectives and design attributes of these ...

  20. Top partner probes of extended Higgs sectors

    E-Print Network [OSTI]

    Kearney, John

    Natural theories of the weak scale often include fermionic partners of the top quark. If the electroweak symmetry breaking sector contains scalars beyond a single Higgs doublet, then top partners can have sizable branching ...

  1. Private Sector Rates (FY 2015) Instrument Technique

    E-Print Network [OSTI]

    Bashir, Rashid

    Source Laser $150 $175 Nanophoton Raman 11 Raman Spectroscopy $150 $175 Newport Solar Simulator Solar Rates for the Material Research Laboratory Facilities Rates for Private Sector companies and researchers

  2. India's pulp and paper industry: Productivity and energy efficiency

    SciTech Connect (OSTI)

    Schumacher, Katja

    1999-07-01T23:59:59.000Z

    Historical estimates of productivity growth in India's pulp and paper sector vary from indicating an improvement to a decline in the sector's productivity. The variance may be traced to the time period of study, source of data for analysis, and type of indices and econometric specifications used for reporting productivity growth. The authors derive both statistical and econometric estimates of productivity growth for this sector. Their results show that productivity declined over the observed period from 1973-74 to 1993-94 by 1.1% p.a. Using a translog specification the econometric analysis reveals that technical progress in India's pulp and paper sector has been biased towards the use of energy and material, while it has been capital and labor saving. The decline in productivity was caused largely by the protection afforded by high tariffs on imported paper products and other policies, which allowed inefficient, small plants to enter the market and flourish. Will these trends continue into the future, particularly where energy use is concerned? The authors examine the current changes in structure and energy efficiency undergoing in the sector. Their analysis shows that with liberalization of the sector, and tighter environmental controls, the industry is moving towards higher efficiency and productivity. However, the analysis also shows that because these improvements are being hampered by significant financial and other barriers the industry might have a long way to go.

  3. Activities to Secure Control Systems in the Energy Sector | Department...

    Office of Environmental Management (EM)

    Activities to Secure Control Systems in the Energy Sector Activities to Secure Control Systems in the Energy Sector Presentation-given at the Federal Utility Partnership Working...

  4. Energy Efficiency Services Sector: Workforce Size and Expectations for Growth

    E-Print Network [OSTI]

    Goldman, Charles

    2010-01-01T23:59:59.000Z

    and market assessment Energy Efficiency Services Sector: Workforce Size2008. “The Size of the U.S. Energy Efficiency Market. Reportmarket spending Energy Efficiency Services Sector: Workforce Size

  5. EIA Energy Efficiency-Commercial Buildings Sector Energy Intensities...

    U.S. Energy Information Administration (EIA) Indexed Site

    Commercial Buildings Sector Energy Intensities Commercial Buildings Sector Energy Intensities: 1992- 2003 Released Date: December 2004 Page Last Revised: August 2009 These tables...

  6. Energy Use in China: Sectoral Trends and Future Outlook

    E-Print Network [OSTI]

    2008-01-01T23:59:59.000Z

    11 Calibration of the Energy Consumption Data forSectoral energy consumption data are available in publishedof the sectoral energy consumption data in the statistics

  7. Sectoral trends in global energy use and greenhouse gas emissions

    E-Print Network [OSTI]

    2006-01-01T23:59:59.000Z

    Building Sector Electricity Consumption parameter logisticin Building Sector Electricity Consumption iii iv Sectoralsome water with electricity consumption, it is not possible

  8. U.S. Energy Information Administration (EIA) - Sector

    Gasoline and Diesel Fuel Update (EIA)

    Transportation sector energy demand Transportation energy use grows slowly in comparison with historical trend figure data Transportation sector energy consumption grows at an...

  9. U.S. Energy Information Administration (EIA) - Sector

    Gasoline and Diesel Fuel Update (EIA)

    Transportation sector energy demand Growth in transportation energy consumption flat across projection figure data The transportation sector consumes 27.1 quadrillion Btu of energy...

  10. Energy Department Announces New Private Sector Partnership to...

    Energy Savers [EERE]

    Energy Department Announces New Private Sector Partnership to Accelerate Renewable Energy Projects Energy Department Announces New Private Sector Partnership to Accelerate...

  11. Climate Change and the Transporation Sector - Challenges and...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Climate Change and the Transporation Sector - Challenges and Mitigation Options Climate Change and the Transporation Sector - Challenges and Mitigation Options 2003 DEER Conference...

  12. The Economics of Public Sector Information

    E-Print Network [OSTI]

    Pollock, Rufus

    result in incentives for over-investment in quality and capacity improvements because, by over-investing, the PSIH stimulates demand and obtains a larger subsidy. In terms of responsiveness an organization operating a more ‘commercial’ pricing policy (e... area (building especially), or keeping up to date with the decisions of their elected representatives. While much data is supplied from outside the public sector, compared to many other areas of the economy, the public sector plays an unusually...

  13. Energy Efficiency Services Sector: Workforce Size and Expectations for Growth

    SciTech Connect (OSTI)

    Goldman, Charles; Fuller, Merrian C.; Stuart, Elizabeth; Peters, Jane S.; McRae, Marjorie; Albers, Nathaniel; Lutzenhiser, Susan; Spahic, Mersiha

    2010-03-22T23:59:59.000Z

    The energy efficiency services sector (EESS) is poised to become an increasingly important part of the U.S. economy. Climate change and energy supply concerns, volatile and increasing energy prices, and a desire for greater energy independence have led many state and national leaders to support an increasingly prominent role for energy efficiency in U.S. energy policy. The national economic recession has also helped to boost the visibility of energy efficiency, as part of a strategy to support economic recovery. We expect investment in energy efficiency to increase dramatically both in the near-term and through 2020 and beyond. This increase will come both from public support, such as the American Recovery and Reinvestment Act (ARRA) and significant increases in utility ratepayer funds directed toward efficiency, and also from increased private spending due to codes and standards, increasing energy prices, and voluntary standards for industry. Given the growing attention on energy efficiency, there is a concern among policy makers, program administrators, and others that there is an insufficiently trained workforce in place to meet the energy efficiency goals being put in place by local, state, and federal policy. To understand the likelihood of a potential workforce gap and appropriate response strategies, one needs to understand the size, composition, and potential for growth of the EESS. We use a bottom-up approach based upon almost 300 interviews with program administrators, education and training providers, and a variety of EESS employers and trade associations; communications with over 50 sector experts; as well as an extensive literature review. We attempt to provide insight into key aspects of the EESS by describing the current job composition, the current workforce size, our projections for sector growth through 2020, and key issues that may limit this growth.

  14. Sectoral trends in global energy use and greenhouse gasemissions

    SciTech Connect (OSTI)

    Price, Lynn; de la Rue du Can, Stephane; Sinton, Jonathan; Worrell, Ernst; Zhou, Nan; Sathaye, Jayant; Levine, Mark

    2006-07-24T23:59:59.000Z

    In 2000, the Intergovernmental Panel on Climate Change (IPCC) published a new set of baseline greenhouse gas (GHG) emissions scenarios in the Special Report on Emissions Scenarios (SRES) (Nakicenovic et al., 2000). The SRES team defined four narrative storylines (A1, A2, B1 and B2) describing the relationships between the forces driving GHG and aerosol emissions and their evolution during the 21st century. The SRES reports emissions for each of these storylines by type of GHG and by fuel type to 2100 globally and for four world regions (OECD countries as of 1990, countries undergoing economic reform, developing countries in Asia, rest of world). Specific assumptions about the quantification of scenario drivers, such as population and economic growth, technological change, resource availability, land-use changes, and local and regional environmental policies, are also provided. End-use sector-level results for buildings, industry, or transportation or information regarding adoption of particular technologies and policies are not provided in the SRES. The goal of this report is to provide more detailed information on the SRES scenarios at the end use level including historical time series data and a decomposition of energy consumption to understand the forecast implications in terms of end use efficiency to 2030. This report focuses on the A1 (A1B) and B2 marker scenarios since they represent distinctly contrasting futures. The A1 storyline describes a future of very rapid economic growth, low population growth, and the rapid introduction of new and more efficient technologies. Major underlying themes are convergence among regions, capacity building, and increased cultural and social interactions, with a substantial reduction in regional differences in per capita income. The B2 storyline describes a world with an emphasis on economic, social, and environmental sustainability, especially at the local and regional levels. It is a world with moderate population growth, intermediate levels of economic development, and less rapid and more diverse technological change (Nakicenovic et al., 2000). Data were obtained from the SRES modeling teams that provide more detail than that reported in the SRES. For the A1 marker scenario, the modeling team provided final energy demand and carbon dioxide (CO{sub 2}) emissions by fuel for industry, buildings, and transportation for nine world regions. Final energy use and CO{sub 2} emissions for three sectors (industry, transport, buildings) for the four SRES world regions were provided for the B2 marker scenario. This report describes the results of a disaggregation of the SRES projected energy use and energy-related CO{sub 2} emissions for the industrial, transport, and buildings sectors for 10 world regions (see Appendix 1) to 2030. An example of further disaggregation of the two SRES scenarios for the residential buildings sector in China is provided, illustrating how such aggregate scenarios can be interpreted at the end use level.

  15. ImSET: Impact of Sector Energy Technologies

    SciTech Connect (OSTI)

    Roop, Joseph M.; Scott, Michael J.; Schultz, Robert W.

    2005-07-19T23:59:59.000Z

    This version of the Impact of Sector Energy Technologies (ImSET) model represents the ''next generation'' of the previously developed Visual Basic model (ImBUILD 2.0) that was developed in 2003 to estimate the macroeconomic impacts of energy-efficient technology in buildings. More specifically, a special-purpose version of the 1997 benchmark national Input-Output (I-O) model was designed specifically to estimate the national employment and income effects of the deployment of Office of Energy Efficiency and Renewable Energy (EERE) -developed energy-saving technologies. In comparison with the previous versions of the model, this version allows for more complete and automated analysis of the essential features of energy efficiency investments in buildings, industry, transportation, and the electric power sectors. This version also incorporates improvements in the treatment of operations and maintenance costs, and improves the treatment of financing of investment options. ImSET is also easier to use than extant macroeconomic simulation models and incorporates information developed by each of the EERE offices as part of the requirements of the Government Performance and Results Act.

  16. Electricity Use in the Pacific Northwest: Utility Historical Sales by Sector, 1989 and Preceding Years.

    SciTech Connect (OSTI)

    United States. Bonneville Power Administration.

    1990-06-01T23:59:59.000Z

    This report officially releases the compilation of regional 1989 retail customer sector sales data by the Bonneville Power Administration. This report is intended to enable detailed examination of annual regional electricity consumption. It gives statistics covering the time period 1970--1989, and also provides observations based on statistics covering the 1983--1989 time period. The electricity use report is the only information source that provides data obtained from each utility in the region based on the amount of electricity they sell to consumers annually. Data is provided on each retail customer sector: residential, commercial, industrial, direct-service industrial, and irrigation. The data specifically supports forecasting activities, rate development, conservation and market assessments, and conservation and market program development and delivery. All of these activities require a detailed look at electricity use. 25 figs., 34 tabs.

  17. Climate VISION: Private Sector Initiatives: Cement: Technology...

    Office of Scientific and Technical Information (OSTI)

    Technology Pathways The DOE's Industries of the Future process helps entire industries articulate their long-term goals and publish them in a unified vision for the future. To...

  18. Clean Energy Manufacturing Initiative Industrial Efficiency and Energy Productivity

    ScienceCinema (OSTI)

    Selldorff, John; Atwell, Monte

    2014-12-03T23:59:59.000Z

    Industrial efficiency and low-cost energy resources are key components to increasing U.S. energy productivity and makes the U.S. manufacturing sector more competitive. Companies find a competitive advantage in implementing efficiency technologies and practices, and technologies developed and manufactured in the U.S. enable greater competitiveness economy-wide.

  19. Industrial Structure and Monetary Policy in a Small Open Economy

    E-Print Network [OSTI]

    Niebur, Ernst

    Industrial Structure and Monetary Policy in a Small Open Economy Thomas A. Lubik Department supply which is empirically quite small. In principle, this link can be broken in a multisectoral economy sectors. This paper reinterprets this line of reasoning in a small open economy with a traded and a non

  20. Clean Energy Manufacturing Initiative Industrial Efficiency and Energy Productivity

    SciTech Connect (OSTI)

    Selldorff, John; Atwell, Monte

    2014-09-23T23:59:59.000Z

    Industrial efficiency and low-cost energy resources are key components to increasing U.S. energy productivity and makes the U.S. manufacturing sector more competitive. Companies find a competitive advantage in implementing efficiency technologies and practices, and technologies developed and manufactured in the U.S. enable greater competitiveness economy-wide.

  1. Centers for manufacturing technology: Industrial Advisory Committee Review

    SciTech Connect (OSTI)

    NONE

    1995-10-01T23:59:59.000Z

    An advisory committee, composed of senior managers form industrial- sector companies and major manufacturing trade associations and representatives from appropriate educational institutions, meets semi-annually to review and advise the Oak Ridge Centers for Manufacturing Technology (ORCMT) on its economic security program. Individual papers have been indexed separately for the database.

  2. Climate VISION: Private Sector Initiatives: Mining: Resources...

    Office of Scientific and Technical Information (OSTI)

    Industry Associations FederalState Programs Technical Information Plant Assessments Training Calendar Software Tools Energy Management Expertise...

  3. Climate VISION: Private Sector Initiatives: Automobile Manufacturers...

    Office of Scientific and Technical Information (OSTI)

    Industry Associations FederalState Programs Technical Information Plant Assessments Training Calendar Software Tools Energy Management Expertise...

  4. Climate VISION: Private Sector Initiatives: Magnesium: Resources...

    Office of Scientific and Technical Information (OSTI)

    Resources & Links Industry Associations FederalState Programs Technical Information Plant Assessments Software Tools Energy Management Expertise...

  5. Climate VISION: Private Sector Initiatives: Chemical Manufacturing...

    Office of Scientific and Technical Information (OSTI)

    Industry Associations FederalState Programs Technical Information Plant Assessments Training Calendar Software Tools Energy Management Expertise...

  6. Climate VISION: Private Sector Initiatives: Forest Products:...

    Office of Scientific and Technical Information (OSTI)

    Industry Associations FederalState Programs Technical Information Plant Assessments Training Calendar Software Tools Energy Management Expertise...

  7. Climate VISION: Private Sector Initiatives: Cement - Resources...

    Office of Scientific and Technical Information (OSTI)

    Industry Associations FederalState Programs Technical Information Plant Assessments Training Calendar Software Tools Energy Management Expertise...

  8. Industrial recovered-materials-utilization targets for the metals and metal-products industry

    SciTech Connect (OSTI)

    None

    1980-03-01T23:59:59.000Z

    The National Energy Conservation Policy Act of 1978 directs DOE to set targets for increased utilization of energy-saving recovered materials for certain industries. These targets are to be established at levels representing the maximum feasible increase in utilization of recovered materials that can be achieved progressively by January 1, 1987 and is consistent with technical and economic factors. A benefit to be derived from the increased use of recoverable materials is in energy savings, as state in the Act. Therefore, emhasis on different industries in the metals sector has been related to their energy consumption. The ferrous industry (iron and steel, ferrour foundries and ferralloys), as defined here, accounts for approximately 3%, and all others for the remaining 3%. Energy consumed in the lead and zinc segments is less than 1% each. Emphasis is placed on the ferrous scrap users, followed by the aluminum and copper industries. A bibliography with 209 citations is included.

  9. Executive Summary - Natural Gas and the Transformation of the U.S. Energy Sector: Electricity

    SciTech Connect (OSTI)

    Logan, J.; Heath, G.; Macknick, J.; Paranhos, E.; Boyd, W.; Carlson, K.

    2013-01-01T23:59:59.000Z

    In November 2012, the Joint Institute for Strategic Energy Analysis (JISEA) released a new report, 'Natural Gas and the Transformation of the U.S. Energy Sector: Electricity.' The study provides a new methodological approach to estimate natural gas related greenhouse gas (GHG) emissions, tracks trends in regulatory and voluntary industry practices, and explores various electricity futures. The Executive Summary provides key findings, insights, data, and figures from this major study.

  10. Contracting Out of Service Activities and the Effects on Sectoral Employment Patterns in South Africa

    E-Print Network [OSTI]

    Tregenna, Fiona

    that it is government that is also responsible for upholding labour legislation). By way of background to the empirical analysis that follows, we have discussed outsourcing as a form of corporate restructuring, which has implications inter alia for the sectoral... outsourcing as a type of shift in corporate and industrial structure, and the specific dynamics of outsourcing in the South African case. This contextualises the empirical analysis of intersectoral shifts in the employment of these two occupations, which...

  11. Third-Party Financing and Power Purchase Agreements for Public Sector PV

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn'tOriginEducationVideoStrategic|Industrial Sector,Department Third Report to the President

  12. North Carolina State University | College of Engineering | Raleigh, NC | www.ncsc.ncsu.edu FOSTERING PRIVATE SECTOR JOB

    E-Print Network [OSTI]

    300 companies annually with project and industry development. The Solar Center is home.ncsc.ncsu.edu FOSTERING PRIVATE SECTOR JOB CREATION AND INVESTMENT The North Carolina Solar Center was founded in 1988 at NC State University. The Solar Center breaks down barriers for clean energy businesses who want

  13. Essays on sectoral shifts of labor demand: measurements and effects on the incidence and the duration of unemployment

    E-Print Network [OSTI]

    Byun, Yanggyu

    2009-05-15T23:59:59.000Z

    industries. Abraham and Katz (1984) point out that this as- 1 The idea of sectoral shifts hypothesis has also been used in recent studies to introduce persistent unemployment in a real business cycle model (Mikhail et al. (2003)), to study the macroeconomic e...

  14. Formulating a VET roadmap for the waste and recycling sector: A case study from Queensland, Australia

    SciTech Connect (OSTI)

    Davis, G., E-mail: gudavis@cytanet.com.cy [Dr Georgina Davis, ABN 12 744 598 837, Banksia Beach, Brisbane, QLD 4507 (Australia)

    2012-10-15T23:59:59.000Z

    Highlights: Black-Right-Pointing-Pointer Existing qualifications do not meet the needs of the sector in Queensland. Black-Right-Pointing-Pointer Businesses may not be best positioned to identify training needs. Black-Right-Pointing-Pointer Companies are developing training internally to meet their own specific needs. Black-Right-Pointing-Pointer Smaller companies lack the resources to develop internal training are disadvantaged. Black-Right-Pointing-Pointer There is industry support for an entry-level, minimum industry qualification. - Abstract: Vocational Education and Training (VET) is an essential tool for providing waste management and recycling workers with the necessary skills and knowledge needed to beneficially influence their own employment and career development; and to also ensure productivity and safe working conditions within the organisations in which they are employed. Current training opportunities within Queensland for the sector are limited and not widely communicated or marketed; with other States, particularly Victoria and New South Wales, realising higher numbers of VET enrollments for waste management courses. This paper presents current VET opportunities and trends for the Queensland waste management sector. Results from a facilitated workshop to identify workforce requirements and future training needs organised by the Waste Contractors and Recyclers Association of Queensland (WCRAQ) are also presented and discussion follows on the future training needs of the industry within Queensland.

  15. Energy Use in China: Sectoral Trends and Future Outlook

    SciTech Connect (OSTI)

    Zhou, Nan; McNeil, Michael A.; Fridley, David; Lin, Jiang; Price,Lynn; de la Rue du Can, Stephane; Sathaye, Jayant; Levine, Mark

    2007-10-04T23:59:59.000Z

    This report provides a detailed, bottom-up analysis ofenergy consumption in China. It recalibrates official Chinese governmentstatistics by reallocating primary energy into categories more commonlyused in international comparisons. It also provides an analysis of trendsin sectoral energy consumption over the past decades. Finally, itassesses the future outlook for the critical period extending to 2020,based on assumptions of likely patterns of economic activity,availability of energy services, and energy intensities. The followingare some highlights of the study's findings: * A reallocation of sectorenergy consumption from the 2000 official Chinese government statisticsfinds that: * Buildings account for 25 percent of primary energy, insteadof 19 percent * Industry accounts for 61 percent of energy instead of 69percent * Industrial energy made a large and unexpected leap between2000-2005, growing by an astonishing 50 percent in the 3 years between2002 and 2005. * Energy consumption in the iron and steel industry was 40percent higher than predicted * Energy consumption in the cement industrywas 54 percent higher than predicted * Overall energy intensity in theindustrial sector grew between 2000 and 2003. This is largely due tointernal shifts towards the most energy-intensive sub-sectors, an effectwhich more than counterbalances the impact of efficiency increases. *Industry accounted for 63 percent of total primary energy consumption in2005 - it is expected to continue to dominate energy consumption through2020, dropping only to 60 percent by that year. * Even assuming thatgrowth rates in 2005-2020 will return to the levels of 2000-2003,industrial energy will grow from 42 EJ in 2005 to 72 EJ in 2020. * Thepercentage of transport energy used to carry passengers (instead offreight) will double from 37 percent to 52 percent between 2000 to 2020,.Much of this increase is due to private car ownership, which willincrease by a factor of 15 from 5.1 million in 2000 to 77 million in2020. * Residential appliance ownership will show signs of saturation inurban households. The increase in residential energy consumption will belargely driven by urbanization, since rural homes will continue to havelow consumption levels. In urban households, the size of appliances willincrease, but its effect will be moderated by efficiency improvements,partially driven by government standards. * Commercial energy increaseswill be driven both by increases in floor space and by increases inpenetration of major end uses such as heating and cooling. Theseincreases will be moderated somewhat, however, by technology changes,such as increased use of heat pumps. * China's Medium- and Long-TermDevelopment plan drafted by the central government and published in 2004calls for a quadrupling of GDP in the period from 2000-2020 with only adoubling in energy consumption during the same period. A bottom-upanalysis with likely efficiency improvements finds that energyconsumption will likely exceed the goal by 26.12 EJ, or 28 percent.Achievements of these goals will there fore require a more aggressivepolicy of encouraging energy efficiency.

  16. Dr. John M. Shaw NSERC Industrial Research Chair in Petroleum Thermodynamics

    E-Print Network [OSTI]

    Firestone, Jeremy

    to the hydrocarbon production, transport and refining sectors. Redefining Heavy Oil Characterization: A DissidentDr. John M. Shaw NSERC Industrial Research Chair in Petroleum Thermodynamics Department of Chemical industrial research chair in petroleum thermodynamics. During his career he has developed expertise

  17. Using E-Commerce in the Forest Products Industry Chapter 1.2.

    E-Print Network [OSTI]

    Using E-Commerce in the Forest Products Industry Chapter 1.2. Using E-Commerce in the Forest The forest products industry is rapidly adopting e-commerce solutions as it advances in the information age. In this chapter, the unique e-commerce needs of this sector's small businesses are discussed. Current experience

  18. Electric Utility Industry Update

    Broader source: Energy.gov [DOE]

    Presentation—given at the April 2012 Federal Utility Partnership Working Group (FUPWG) meeting—covers significant electric industry trends and industry priorities with federal customers.

  19. Uranium industry annual 1997

    SciTech Connect (OSTI)

    NONE

    1998-04-01T23:59:59.000Z

    This report provides statistical data on the U.S. uranium industry`s activities relating to uranium raw materials and uranium marketing.

  20. CASL Industry Council Meeting

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    IndustryCouncil.shtml The new members that joined the Industry Council include NPP owneroperators with analysis capability: Tyrone Stevens of Exelon, and SMR vendors:...

  1. Live Webinar on Better Buildings Challenge: Public-Sector Update

    Broader source: Energy.gov [DOE]

    The Energy Department will present a live webinar titled "Better Buildings Challenge: Public-Sector Update."

  2. Distributed Generation Potential of the U.S. Commercial Sector

    E-Print Network [OSTI]

    LaCommare, Kristina Hamachi; Edwards, Jennifer L.; Gumerman, Etan; Marnay, Chris

    2005-01-01T23:59:59.000Z

    residential and commercial sector installations, for a total of 9 GW. Clearly, commercial DG with CHP

  3. Varieties of innovation : the creation of wind and solar industries in China, Germany, and the United States

    E-Print Network [OSTI]

    Nahm, Jonas M

    2014-01-01T23:59:59.000Z

    Where and how does innovation take place in contemporary high-technology sectors? Theories of innovation presume a division of labor between firms in industrialized economies that invent and commercialize new technologies ...

  4. China's Top-1000 Energy-Consuming Enterprises Program: Reducing Energy Consumption of the 1000 Largest Industrial Enterprises in China

    E-Print Network [OSTI]

    Price, Lynn

    2008-01-01T23:59:59.000Z

    03/06/content_7729607.htm ETSU, 1999. Industrial SectorSee discussion of this report in ETSU, AEA Technology, 2001.environment/ccl/pdf/etsu-analysis.pdf Feng, F. , 2007. “

  5. Crossing the Valley of Death: Policy Options to Advance the Uptake of Energy-Efficient Emerging Technologies in US Industry 

    E-Print Network [OSTI]

    Harris, J.; Bostrom, P.; Lung, R. B.

    2011-01-01T23:59:59.000Z

    operating practices. In the United States the industrial sector is impacted by many policies-fiscal and monetary, economic development, energy pricing, climate legislation, tax code, and direct subsidies, among others-all of which help shape the strategy...

  6. Characterization of industrial process waste heat and input heat streams

    SciTech Connect (OSTI)

    Wilfert, G.L.; Huber, H.B.; Dodge, R.E.; Garrett-Price, B.A.; Fassbender, L.L.; Griffin, E.A.; Brown, D.R.; Moore, N.L.

    1984-05-01T23:59:59.000Z

    The nature and extent of industrial waste heat associated with the manufacturing sector of the US economy are identified. Industry energy information is reviewed and the energy content in waste heat streams emanating from 108 energy-intensive industrial processes is estimated. Generic types of process equipment are identified and the energy content in gaseous, liquid, and steam waste streams emanating from this equipment is evaluated. Matchups between the energy content of waste heat streams and candidate uses are identified. The resultant matrix identifies 256 source/sink (waste heat/candidate input heat) temperature combinations. (MHR)

  7. Advanced Industrial Materials (AIM) Program annual progress report, FY 1997

    SciTech Connect (OSTI)

    NONE

    1998-05-01T23:59:59.000Z

    The Advanced Industrial Materials (AIM) Program is a part of the Office of Industrial Technologies (OIT), Energy Efficiency and Renewable Energy, US Department of Energy (DOE). The mission of AIM is to support development and commercialization of new or improved materials to improve energy efficiency, productivity, product quality, and reduced waste in the major process industries. OIT has embarked on a fundamentally new way of working with industries--the Industries of the Future (IOF) strategy--concentrating on the major process industries that consume about 90% of the energy and generate about 90% of the waste in the industrial sector. These are the aluminum, chemical, forest products, glass, metalcasting, and steel industries. OIT has encouraged and assisted these industries in developing visions of what they will be like 20 or 30 years into the future, defining the drivers, technology needs, and barriers to realization of their visions. These visions provide a framework for development of technology roadmaps and implementation plans, some of which have been completed. The AIM Program supports IOF by conducting research and development on materials to solve problems identified in the roadmaps. This is done by National Laboratory/industry/university teams with the facilities and expertise needed to develop new and improved materials. Each project in the AIM Program has active industrial participation and support.

  8. Profile of the chemicals industry in California: Californiaindustries of the future program

    SciTech Connect (OSTI)

    Galitsky, Christina; Worrell, Ernst

    2004-06-01T23:59:59.000Z

    The U.S. Department of Energy (DOE) Office of Industrial Technologies (OIT) established the Industries of the Future (IOF) program to increase energy efficiency, reduce waste production and to improve competitiveness, currently focusing on nine sectors. The IOF is a partnership strategy involving industry, the research community and the government, working together to identify technology needs, promote industrial partnerships and implement joint measures with all partners involved. The State Industries of the Future (SIOF) program delivers the accomplishments of the national Industries of the Future strategy to the local level, to expand the technology opportunities to a larger number of partners and reach smaller businesses and manufacturers that were not initially involved in the IOF effort. The state programs bring together industry, academia, and state agencies to address the important issues confronting industry in the state. These public-private coalitions facilitate industry solutions locally and enhance economic development. California has started a State Industries of the Future effort, in collaboration with the U.S. Department of Energy. The California Energy Commission (CEC) is leading the SIOF program in California, as part of many other programs to improve the energy efficiency and performance of industries in California. The California State IOF program aims to build a network of participants from industry, academia and government in four selected industrial sectors as a basis for the development of a strategic partnership for industrial energy efficient technology in the state. In California the IOF effort focuses petroleum refining, chemical processing, food processing and electronics. As part of this effort, the SIOF program will develop roadmaps for technology development for the selected sectors. On the basis of the roadmap, the program will develop successful projects with co-funding from state and federal government, and promote industry-specific energy-efficiency. An important element of the SIOF-program is the preparation of R&D roadmaps for each of the selected industries. The roadmap will help to identify priority needs for the participating industries to meet their energy challenges. The roadmap effort builds on the roadmaps developed by DOE, and on the conditions specific for the industry in California. Key to the successful preparation of a roadmap in the selected industries is the development of a profile of the industries. The profile provides a basis for the participants in the roadmap-effort, especially as the structure of the industries in California can be different than in the nation. The sector profiles describe the current economic and energy situation of these industries in California, the processes and energy uses, and the potential future developments in each industry. The profiles are an integral part of the roadmap, to help working group partners to evaluate the industry's R&D needs for their industry in California. In this report, we focus on the chemicals industry. The industry is an important economic factor in the state, providing over 82,300 jobs directly, and more in indirect employment. Value of shipments in 2001 was just under $25.7 Billion, or 6% of all manufacturing in California. There are over 1,500 chemical plants in California, of which 52% are pharmaceutical companies. Many companies operate chemical plants in California. The industry consumes 8% of the electricity and 5% of the natural gas in California. In this report, we start with a description of the chemical industry in the United States and California. This is followed by a discussion of the energy consumption and energy intensity of the Californian chemical industry. Chapter 3 focuses on the main sub-sectors. For each of the sub-sectors a general process description is provided in Chapter 4. Based on this analysis, in Chapter 5, we discuss potential technology developments that can contribute to further improving the energy efficiency in chemical plants, with a focus on the situation in California.

  9. Process Control Systems in the Chemical Industry: Safety vs. Security

    SciTech Connect (OSTI)

    Jeffrey Hahn; Thomas Anderson

    2005-04-01T23:59:59.000Z

    Traditionally, the primary focus of the chemical industry has been safety and productivity. However, recent threats to our nation’s critical infrastructure have prompted a tightening of security measures across many different industry sectors. Reducing vulnerabilities of control systems against physical and cyber attack is necessary to ensure the safety, security and effective functioning of these systems. The U.S. Department of Homeland Security has developed a strategy to secure these vulnerabilities. Crucial to this strategy is the Control Systems Security and Test Center (CSSTC) established to test and analyze control systems equipment. In addition, the CSSTC promotes a proactive, collaborative approach to increase industry's awareness of standards, products and processes that can enhance the security of control systems. This paper outlines measures that can be taken to enhance the cybersecurity of process control systems in the chemical sector.

  10. ESCO market and industry trends: Updated results from the NAESCO database project

    SciTech Connect (OSTI)

    Osborn, Julie G.; Goldman, Charles A.; Hopper, Nicole C.

    2001-10-15T23:59:59.000Z

    Today's U.S. energy efficiency services industry is one of the most successful examples of private sector energy efficiency services in the world, yet little empirical information is available on the actual market activity of this industry. LBNL, together with the National Association of Energy Services Companies (NAESCO), has compiled the most comprehensive dataset of the energy efficiency services industry: nearly 1,500 case studies of energy efficiency projects. Our analysis of these projects helps shed light on some of the conventional wisdom regarding industry performance and evolution. We report key statistics about typical projects and industry trends that will aid state, federal, and international policymakers, and other investors interested in the development of a private sector energy efficiency services industry.

  11. Industry Analysis February 2013

    E-Print Network [OSTI]

    Abolmaesumi, Purang

    technology ­ Clean tech/ clean technology #12;7 Industry Studies · IbisWorld ­ U.S. and global industry-Industries · Biodiesel ­ Biofuel ­ Alternate fuels ­ Green fuels ­ Renewable fuels/energy ­ Green energy ­ Green Canada, Census, Industry Canada, the OECD, European Union, IMF, World Bank, UN . . . Never pay for stats

  12. INDUSTRIAL ENGINEERING GRADUATE PROGRAMS

    E-Print Network [OSTI]

    Gelfond, Michael

    : Occupational biomechanics, work physiology, industrial ergonomics, environmental hygiene, cognitive engineeringINDUSTRIAL ENGINEERING GRADUATE PROGRAMS The Master of Science in Industrial Engineering (M Systems and Engineering (M.S.M.S.E.), the Doctor of Philosophy in Industrial Engineering, and the Doctor

  13. Geothermal industry employment: Survey results & analysis

    SciTech Connect (OSTI)

    Not Available

    2005-09-01T23:59:59.000Z

    The Geothermal Energy Association (GEA) is ofteh asked about the socioeconomic and employment impact of the industry. Since available literature dealing with employment involved in the geothermal sector appeared relatively outdated, unduly focused on certain activities of the industry (e.g. operation and maintenance of geothermal power plants) or poorly reliable, GEA, in consultation with the DOE, decided to conduct a new employment survey to provide better answers to these questions. The main objective of this survey is to assess and characterize the current workforce involved in geothermal activities in the US. Several initiatives have therefore been undertaken to reach as many organizations involved in geothermal activities as possible and assess their current workforce. The first section of this document describes the methodology used to contact the companies involved in the geothermal sector. The second section presents the survey results and analyzes them. This analysis includes two major parts. The first part analyzes the survey responses, presents employment numbers that were captured and describes the major characteristics of the industry that have been identified. The second part of the analysis estimates the number of workers involved in companies that are active in the geothermal business but did not respond to the survey or could not be reached. Preliminary conclusions and the study limits and restrictions are then presented. The third section addresses the potential employment impact related to manufacturing and construction of new geothermal power facilities. Indirect and induced economic impacts related with such investment are also investigated.

  14. Climate VISION: Private Sector Initiatives: Aluminum: Resources...

    Office of Scientific and Technical Information (OSTI)

    Industry Associations Aluminum Association The Aluminum Association, Inc. is the trade association for producers of primary aluminum, recyclers and semi-fabricated aluminum...

  15. Climate VISION: Private Sector Initiatives: Mining: Resources...

    Office of Scientific and Technical Information (OSTI)

    Technical Information Publications Case Studies Publications The Mining Industry Climate Action Plan (MICAP) (PDF 308 KB) Download Acrobat Reader MICAP focuses on carbon dioxide...

  16. Climate VISION: Private Sector Initiatives: Cement: Resources...

    Office of Scientific and Technical Information (OSTI)

    Resources & Links Technical Information Publications Case Studies Publications Energy Efficiency and Carbon Dioxide Emission Reduction Opportunities in the U.S. Cement Industry,...

  17. Climate VISION: Private Sector Initiatives: Forest Products:...

    Office of Scientific and Technical Information (OSTI)

    Industry Associations American Forest & Paper Association (AF&PA) AF&PA's message is to provide significant value to member companies through outstanding performance in those areas...

  18. Climate VISION: Private Sector Initiatives: Mining: Technology...

    Office of Scientific and Technical Information (OSTI)

    Technology Pathways As part of the mining vision process, industry develops technology roadmaps to identify critical pathways for the R&D needed to reach their goals. These...

  19. Climate VISION: Private Sector Initiatives: Semiconductors

    Office of Scientific and Technical Information (OSTI)

    Agreements The U.S. semiconductor industry, represented by the members of the Environmental Protection Agency's PFC ReductionClimate Partnership for the Semiconductor...

  20. Climate VISION: Private Sector Initiatives: Aluminum

    Office of Scientific and Technical Information (OSTI)

    Voluntary Aluminum Industry Partnership (VAIP), representing 98% of primary aluminum production in the United States, have committed under the Climate VISION program to a direct...

  1. Climate VISION: Private Sector Initiatives: Chemical Manufacturing

    Office of Scientific and Technical Information (OSTI)

    American Chemistry Council (ACC), representing 85% of the chemical industry production in the U.S., has agreed American Chemistry Council Logo to an overall greenhouse gas...

  2. Climate VISION: Private Sector Initiatives: Magnesium: Resources...

    Office of Scientific and Technical Information (OSTI)

    intends to eliminate emissions of SF6 by evaluating and adopting environmentally friendly alternative protective cover gases. The industry may also seek to improve its energy...

  3. Climate VISION: Private Sector Initiatives: Aluminum: Resources...

    Office of Scientific and Technical Information (OSTI)

    Resources & Links Industry Associations FederalState Programs Technical Information Plant Assessments Training Calendar Software Tools Energy Management Expertise Auto Aluminum...

  4. Climate VISION: Private Sector Initiatives: Magnesium: Resources...

    Office of Scientific and Technical Information (OSTI)

    Industry Associations International Magnesium Association Founded in 1943, the mission of the International Magnesium Association (IMA) is to promote the use of the metal magnesium...

  5. Climate VISION: Private Sector Initiatives: Aluminum: Resources...

    Office of Scientific and Technical Information (OSTI)

    Partnership The Voluntary Aluminum Industrial Partnership (VAIP) is an innovative pollution prevention program developed jointly by the U.S. Environmental Protection Agency...

  6. Climate VISION: Private Sector Initiatives: Aluminum: Technology...

    Office of Scientific and Technical Information (OSTI)

    producers recognize that reducing greenhouse gas emissions and improving energy efficiency offers a competitive edge in world markets. In 1996, the U.S. industry entered into...

  7. Climate VISION: Private Sector Initiatives: Mining: Resources...

    Office of Scientific and Technical Information (OSTI)

    Publications The Industrial Technologies Program offers a wide array of publications, videos, software, and other information products for improving energy efficiency in the...

  8. Climate VISION: Private Sector Initiatives: Forest Products:...

    Office of Scientific and Technical Information (OSTI)

    Publications The Industrial Technologies Program offers a wide array of publications, videos, software, and other information products for improving energy efficiency in the...

  9. Climate VISION: Private Sector Initiatives: Aluminum: Resources...

    Office of Scientific and Technical Information (OSTI)

    Industry of the Future Tools & Publications ITP offers a wide array of publications, videos, software, and other information products for improving energy efficiency in the...

  10. Climate VISION: Private Sector Initiatives: Chemical Manufacturing...

    Office of Scientific and Technical Information (OSTI)

    Publications The Industrial Technologies Program offers a wide array of publications, videos, software, and other information products for improving energy efficiency in the...

  11. Climate VISION: Private Sector Initiatives: Magnesium: Resources...

    Office of Scientific and Technical Information (OSTI)

    Washington in February of 2002. The paper briefly describes the issues surrounding climate change and the Magnesium Industry, and gives an overview of the SF6 Emission...

  12. Industrial Energy Audit Guidebook: Guidelines for Conducting an Energy Audit in Industrial Facilities

    SciTech Connect (OSTI)

    Hasanbeigi, Ali; Price, Lynn

    2010-10-07T23:59:59.000Z

    Various studies in different countries have shown that significant energy-efficiency improvement opportunities exist in the industrial sector, many of which are cost-effective. These energy-efficiency options include both cross-cutting as well as sector-specific measures. However, industrial plants are not always aware of energy-efficiency improvement potentials. Conducting an energy audit is one of the first steps in identifying these potentials. Even so, many plants do not have the capacity to conduct an effective energy audit. In some countries, government policies and programs aim to assist industry to improve competitiveness through increased energy efficiency. However, usually only limited technical and financial resources for improving energy efficiency are available, especially for small and medium-sized enterprises. Information on energy auditing and practices should, therefore, be prepared and disseminated to industrial plants. This guidebook provides guidelines for energy auditors regarding the key elements for preparing for an energy audit, conducting an inventory and measuring energy use, analyzing energy bills, benchmarking, analyzing energy use patterns, identifying energy-efficiency opportunities, conducting cost-benefit analysis, preparing energy audit reports, and undertaking post-audit activities. The purpose of this guidebook is to assist energy auditors and engineers in the plant to conduct a well-structured and effective energy audit.

  13. Conceptualising Inventory Prepositioning in the Humanitarian Sector

    E-Print Network [OSTI]

    Boyer, Edmond

    Conceptualising Inventory Prepositioning in the Humanitarian Sector Delia Richardson, Sander de chain to reduce delivery time of relief inventory improves responsiveness. This is the essence of inventory pre-positioning (IPP). IPP is yet to be clearly defined; and the main factors affecting IPP

  14. WATER AND ENERGY SECTOR VULNERABILITY TO CLIMATE

    E-Print Network [OSTI]

    WATER AND ENERGY SECTOR VULNERABILITY TO CLIMATE WARMING IN THE SIERRA NEVADA: Water Year explores the sensitivity of water indexing methods to climate change scenarios to better understand how water management decisions and allocations will be affected by climate change. Many water management

  15. NATURAL GAS ADVISORY COMMITTEE Name Affiliation Sector

    E-Print Network [OSTI]

    NATURAL GAS ADVISORY COMMITTEE 2011-2013 Name Affiliation Sector Dernovsek, David Bonneville Power Defenbach, Byron Intermountain Gas Distribution Dragoon, Ken NWPCC Council Friedman, Randy NW Natural Gas Distribution Gopal, Jairam Southern CA Edison Electric Utility Hamilton, Linda Shell Trading Gas & Power

  16. End User Functional and Performance Requirements for HTGR Energy Supply to Industrial Processes

    SciTech Connect (OSTI)

    L.E. Demick

    2010-09-01T23:59:59.000Z

    This document specifies end user functional and performance requirements to be used in the development of the design of a high temperature gas-cooled reactor (HTGR) based plant supplying energy to industrial processes. These requirements were developed from collaboration with industry and HTGR suppliers and from detailed evaluation of integration of the HTGR technology in industrial processes. The functional and performance requirements specified herein are an effective representation of the industrial sector energy needs and an effective basis for developing a plant design that will serve the broadest range of industrial applications.

  17. Assessing U.S. ESCO industry performance and market trends: Results from the NAESCO database project

    SciTech Connect (OSTI)

    Osborn, Julie; Goldman, Chuck; Hopper, Nicole; Singer, Terry

    2002-05-15T23:59:59.000Z

    The U.S. Energy Services Company (ESCO) industry is often cited as the most successful model for the private sector delivery of energy-efficiency services. This study documents actual performance of the ESCO industry in order to provide policymakers and investors with objective informative and customers with a resource for benchmarking proposed projects relative to industry performance. We have assembled a database of nearly 1500 case studies of energy-efficiency projects - the most comprehensive data set of the U.S. ESCO industry available. These projects include $2.55B of work completed by 51 ESCOs and span much of the history of this industry.

  18. Industry Leaders Saving Energy | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742Energy ChinaofSchaefer To:DepartmentDepartmentEnergy AprilWith theIndustrial Sector

  19. SOLAR HEATING OF TANK BOTTOMS Application of Solar Heating to Asphaltic and Parrafinic Oils Reducing Fuel Costs and Greenhouse Gases Due to Use of Natural Gas and Propane

    SciTech Connect (OSTI)

    Eugene A. Fritzler

    2005-09-01T23:59:59.000Z

    The sale of crude oil requires that the crude meet product specifications for BS&W, temperature, pour point and API gravity. The physical characteristics of the crude such as pour point and viscosity effect the efficient loading, transport, and unloading of the crude oil. In many cases, the crude oil has either a very high paraffin content or asphalt content which will require either hot oiling or the addition of diluents to the crude oil to reduce the viscosity and the pour point of the oil allowing the crude oil to be readily loaded on to the transport. Marginal wells are significantly impacted by the cost of preheating the oil to an appropriate temperature to allow for ease of transport. Highly paraffinic and asphaltic oils exist throughout the D-J basin and generally require pretreatment during cold months prior to sales. The current study addresses the use of solar energy to heat tank bottoms and improves the overall efficiency and operational reliability of stripper wells.

  20. The US steel industry: An energy perspective

    SciTech Connect (OSTI)

    Azimi, S. A.; Lowitt, H. E.

    1988-01-01T23:59:59.000Z

    This report investigates the state of the US steel industry in terms of energy consumption and conservation. The specific objectives were: to update and verify energy and materials consumption data at the various process levels in 1983; to determine the potential energy savings attainable with current (1983), state-of-the-art, and future production practices and technologies (2000); and to identify new areas of research and development opportunity that will enable these potential future savings to be achieved. The results of this study concluded that in year 2000, there is a potential to save between 40% and 46% of the energy used in current production practices, dependent on the projected technology mix. R and D needs and opportunities were identified for the industry. Potential R and D candidates for DOE involvement with the private sector were assessed and selected from the identified list.