Powered by Deep Web Technologies
Note: This page contains sample records for the topic "indicators rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Rotary torque and rpm indicator for oil well drilling rigs  

SciTech Connect

Monitoring the torque applied by the rotary table to the drill string and the rpm of the drill string is provided. An intermediate adapter is positioned between the drill kelly and the rotary table. A strain gauge is attached to the intermediate adapter to measure torsional deformation and provide an indication of rotary torque. Transmission of torque data is accomplished by radio frequency transmission utilizing a transmitter on the intermediate adapter. A receiver is mounted to the side of the drill rig floor to receive and demodulate the torque signal. The intermediate adapter is rotating at the same rate as the drill string. Detection of the revolutions utilizing the changing R.F. Field strength is accomplished at the edge of the drill rig platform or elsewhere with a stationary sensor which doubles as the torque receiver. A highly directional torque transmitter antenna mounted on the adapter is used with the major lobe lying parallel to the rig floor and perpendicular to the pipe. By detecting the envelope of the radio frequency field strength, each rotation is marked by a peak. This enables continuous torque and rpm monitoring.

Chien, L.C.

1981-08-25T23:59:59.000Z

2

Focus on rotary drill rigs  

SciTech Connect

This article discusses the drill rig, focusing on the rotary drill rigs. There are two principal drilling methods - rotary and percussion. In certain situations, percussion drilling is the most practical method, but for most applications, rotary drilling using the rotary-tricone bit with either steel-toothed cones or carbide inserts, is the common and accepted drilling technique. There are four principal reasons for a rotary drill rig: to provide power to the rotary-tricone bit; to provide air to clean the hole; to provide a life-support system for the rotary-tricone bits; and, to provide a stable and efficient platform from which to drill the hole.

Schivley, G.P. Jr.

1987-06-01T23:59:59.000Z

3

Rotating head for rotary drilling rigs  

SciTech Connect

A rotating head is claimed for a rotary drilling rig which is to be secured to the top of a well pipe having an inner rotating portion with an opening therethrough which permits passage of drill pipe, pipe joints, and Kelly tools; the rotating portion has an annular drive rubber formed integrally with the top portion thereof. A rotating head drive bushing having an opening with a cross-sectional shape generally conforming to the cross-section of the Kelly tool to permit only sliding motion therebetween is provided with helical external ridges which produce a disengagable gripping action with the opening in the drive rubber at the top of the rotating portion of the rotating head. The rotating portion has a conventional stripper rubber at the bottom thereof and is mounted with a double roller bearing to provide low friction motion with respect to the fixed portion of the head. The double roller bearing is lubricated with a viscous lubricating material and paddles are provided between the sets of rollers of the double roller bearing for distributing the viscous lubricating material and in particular propel it onto the upper set of bearings; the upper body portion of the rotating head is readily detachable from the lower sleeve portion which is normally welded to the well conductor pipe.

Adams, J.R.

1983-09-27T23:59:59.000Z

4

34th annual reed rotary rig census  

SciTech Connect

This article reports that the number of rigs active according to the 1986 census is 1052, which represents a decline of 1573 rigs from 1985 figures. This 60 percent decrease is the largest decline of active rigs in the 34-year history of the census. The 1986 census takers found 3993 rigs are available with the capacity to drill deeper than 3000 ft. The count has thus declined by 416 rigs (9 percent) from the 1985 total of 4409. Rig availability declined for the fourth consecutive year following nine straight years of fleet expansion (1974-1982). During the past four years, 1651 rigs have been removed from the drilling fleet representing a 29 percent decline from the record high number of rigs available in 1982. The 1986 decline in the available U.S. fleet is considerably less than what many industry observers had been anticipating. A larger decrease in the rig fleet has not been realized for a number of reasons.

Hutchinson, D.L.; Pastusek, P.E.

1986-10-01T23:59:59.000Z

5

New ultra-deepwater rig with dual rotaries will reduce costs  

SciTech Connect

The Discoverer Enterprise, a next generation, ultra-deepwater drill ship with a dual rotary system, will decrease drilling and completion costs by reducing bottom hole assembly (BHA) and tubular preparation time. Transocean Offshore received a contract from Amoco Corp. to build the ultra-deep floating rig and is scheduled to spud its first well in July 1998. It will generally work in water deeper than 6,000 ft. The rig design involves a new approach that addresses the overall well-construction process and equipment required to decrease significantly deepwater drilling time. The Discoverer is the first ultra-deepwater rig designed specifically for handling subsea completions and extended well tests. The paper discusses increased deepwater rig demand, rig construction costs, drillship design, well construction, development drilling, and cost justification.

Cole, J.C.; Herrmann, R.P.; Scott, R.J. [Transocean Offshore Inc., Houston, TX (United States); Shaughnessy, J.M. [Amoco Corp., Houston, TX (United States)

1997-05-26T23:59:59.000Z

6

International land rig locator  

SciTech Connect

Mechanical specifications, ratings, locations, and status are listed for each of the 5,000 contract rotary drilling rigs operated by the more than 700 independent drilling contractors throughout the Free World.

Not Available

1984-03-01T23:59:59.000Z

7

International land rig locator  

SciTech Connect

Mechanical specifications, ratings, locations, and status are listed for each of the 5,000 contract rotary drilling rigs operated by more than 700 independent drilling contractors throughout the Free World.

Not Available

1983-09-01T23:59:59.000Z

8

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

12-i Chapter 12 Rigging Hardware CHAPTER 12 RIGGING HARDWARE This chapter provides requirements for rigging accessories used in hoisting and rigging - shackles, eyebolts, eye nuts, links, rings, swivels, wire-rope clips, turnbuckles, rigging hooks, and load-indicating devices and implements the requirements of ANSI/ASME B30.26, "Rigging Hardware" (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). 12.1 GENERAL..................................................................................................................................12-1 12.1.1 Good and Bad Rigging Practices ...................................................................................12-1 12.2 RIGGING HOOKS.....................................................................................................................12-5

9

44. Annual Reed rig census  

SciTech Connect

Reed Tool Company`s 44th annual rotary rig census found a spirit of increased optimism in the US oil and gas drilling industry. Rig utilization rose to 77% this year, the highest since the boom times of 15 years ago. A combination of a higher number of active rigs and another decline in available units to a historical low, led to this higher-than-average utilization rate. The paper discusses results from the survey.

Stokes, T.A.; Rodriguez, M.R. [Reed Tool Co., Houston, TX (United States)

1996-10-01T23:59:59.000Z

10

Comparing rig power transmission systems  

SciTech Connect

Installed power on drilling rigs has increased steadily since the inception of rotary drilling technology as a result of technical advances and the need to penetrate deeper horizons. Higher power levels for the pumps, rotary table and drawworks are also required for drilling deep wells within an economically reasonable period. Power initially available on a rig had been about 35 kW on average, whereas power values on modern rigs drilling ultra-deep wells are on the order of several thousand kW. The installed power values on modern drilling rigs, subdivided with respect to depth range, are shown. After safety, economic factors are of paramount importance to rig operators. Among these, which include low acquisition cost, long service life and ease of maintenance, a particularly decisive factor is high efficiency.

Gutsche, W.; Noevig, T.

1989-04-01T23:59:59.000Z

11

45th annual Reed rig census  

SciTech Connect

Since 1983, Reed Tool Co.`s annual rotary rig census has reported 14 consecutive annual reductions in the U.S. rig fleet. This year, the downward trend has reversed and more rigs have been added to the available fleet than have left. Robust drilling activity has also spurred higher rig utilization in 1997. Utilization climbed to 86.9% this year, more than ten percentage points higher than a year ago and the highest since 1981. Data and trends are discussed.

Stokes, T.A.; Rodriguez, M.R. [Reed Tool Co., Houston, TX (United States)

1997-10-01T23:59:59.000Z

12

Rotary blasthole drilling update  

SciTech Connect

Blasthole drilling rigs are the unsung heroes of open-pit mining. Recently manufacturers have announced new tools. Original equipment manufactures (OEMs) are making safer and more efficient drills. Technology and GPS navigation systems are increasing drilling accuracy. The article describes features of new pieces of equipment: Sandvik's DR460 rotary blasthole drill, P & H's C-Series drills and Atlas Copco's Pit Viper PV275 multiphase rotary blasthole drill rig. DrillNav Plus is a blasthole navigation system developed by Leica Geosystems. 5 photos.

Fiscor, S.

2008-02-15T23:59:59.000Z

13

New depths with mobile rig  

SciTech Connect

Magee-Poole Drilling Company, a drilling contractor operating out of the south Texas drilling center of Alice, claims it operates the largest mobile drilling rig in the world. That is, it's the only wheel mounted portable rig that drills to 16,000 feet with 4 1/2-inch drill pipe - at least 3000 feet deeper than the previous mobile drilling rig ratings. The unit is designated the Ingersoll-Rand 1500 Series. What's more significant, according to co-owner Don Magee, is that the rig's portability gets the rotary table turning to the right sooner; it drills more footage per year. It rigs up in 1 1/2 days versus 3 to 4 days for a conventional skid type rig normally used at these depths. The unit's compact arrangement, with more components combined into single loads, makes possible its higher mobility. A conventional skid rig might require 25 to 30 truckloads to move the rig components, mud system, fuel and water tank, houses for utilities, storage and crew change, generators, and drill pipe. The new rig moves in anywhere from four to nine loads less. Further, the rig components weigh less without sacrificing durability.

Not Available

1982-03-01T23:59:59.000Z

14

Rig activity; 1989 was the worst year on record  

SciTech Connect

This article discusses the quantity of oil rotary rigs running in the United States during 1989. Rotary rigs running in 1989 averaged 870, down 7.1% from 1988 and arguably the worst performance since anyone bothered to count. A quick check into dusty historical records reveals that in 1942 the rotary rig count averaged 761 (this was the result of a deliberate government policy of scaling back drilling). However, the number is misleading, because in the early 1940s cable-tool rigs were around 40% to 45% of the total operating at any given time.

Not Available

1990-02-01T23:59:59.000Z

15

42nd Annual Reed rig census  

SciTech Connect

The eleven-year trend of attrition in the US rig fleet slowed significantly this year as only 12 rigs, or less than 1%, left the available fleet. The number of rotary rigs available for drilling in the US now stands at 1,841. but for the 42-year history of the Reed Tool Co. Rotary Rig Census, the 1973 available rig count of 1,767 remains the record low for yet another year. The count of rigs active during the 45-day census period also declined since last year's census. The active count was down 4.5% to 1,221 from 1,279 in 1993. As a consequence, rig utilization fell to 66.3% in 1994, from 69.0% last year. Notably, a strong shift to gas from oil drilling has occurred. Of the 1,221 rigs active in the census period, 540 were drilling for gas on the last well vs. 356 drilling for oil. Compared to last year, this is an increase in gas drilling of 29% and a decrease in oil drilling 22%. (Rigs targeting both oil and gas totaled 325 in 1994.)

Stokes, T.A.; Rodriquez, M.R. (Reed Tool Co., Houston, TX (United States))

1994-10-01T23:59:59.000Z

16

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

9-2004 9-2004 12-i Chapter 12 Rigging Accessories CHAPTER 12 RIGGING ACCESSORIES This chapter provides requirements for rigging accessories used in hoisting and rigging - shackles, eyebolts, rings, wire-rope clips, turnbuckles, rigging hooks, and load-indicating devices. 12.1 GENERAL ...............................................................................................................................12-1 12.1.1 Inspections .................................................................................................................12-1 12.1.2 Testing .....................................................................................................................12-3 12.1.3 Good and Bad Rigging Practices ...............................................................................12-3

17

36th annual Reed rig census  

SciTech Connect

For the sixth straight year, the number of rigs available in the U.S. declined. Five hundred and seventy-nine rotary rigs dropped out of drilling industry competition during the past 12 months as attrition forced rig supply closer toward balance with demand. Significant highlights of this year's census are: The U.S. rig fleet now stands at 2,752 drilling rigs, a 17.4% reduction from the census count in 1987. This is the largest percentage decline and the third largest absolute decline in available rigs in census history; The 1988 census active count was 1,532 rigs, up 10% over 1987; The 1988 census utilization rate was 55.7%, up from the 41.7% reported last year and a 110% improvement over the all-time low of 26.3% in 1986; Every region in the country reported a reduction in total available rigs. Each region also reported an increase in the active ring count with the exception of Ark-La-Tex; California had the highest utilization rate in the census (63.9%), and all regions reported a utilization rate greater than 50% with the exception of Ark-La-Tex, which reported a 45.5% rate; The number of rig owners declined 12% from 691 to 608. The decline in available rigs would have been greater, but owners brought back 226 rigs that had been dropped from previous census tabulations.

Fitts, R.L.; Crowhurst, M.E. (Reed Tool Co., Houston, TX (US))

1988-10-01T23:59:59.000Z

18

Drill rig hook  

SciTech Connect

A hook for suspending a pipe string or other load in a well rig, including a tubular outer body supported by a first connector structure which is attachable to a suspending line, a tubular inner body which supports a second connector structure preferably taking the form of a hook, with the inner body being received within the outer body and being yieldingly urged upwardly relative thereto by a resilient unit or assembly located within the inner body, and with a structure within the inner body bearing upwardly against and supporting the resilient assembly and attached to the first connector structure. A cam mechanism between the inner and outer bodies automatically cams the inner body to a predetermined rotary position upon upward movement, with a locking device or devices serving to retain the inner body in fixed rotary position and/or to lock the camming mechanism in a fixed position in a manner determining the rotary setting to which the inner body returns upon upward movement. The mentioned first and/or second connectors may each consist of two parts receivable within one of the tubular bodies and held in operative connecting engagement therewith by a spacer between the two parts. A link suporting member may be formed separately from the load suporting hook, to be detachable therefrom for a repair or replacement.

Zimmermann, A.

1985-02-12T23:59:59.000Z

19

Rig activity; 1991 is now the worst year on record  

SciTech Connect

This paper reports that U.S. rotary oil well drilling rig activity reached year-end levels above 1,100 rigs and averaged over 1,000 in 1990, the first increase since 1984. In 1991, however, operating rigs dropped once again, this time to an all time recorded low and once again, most forecasters erred on the high side. Rotary rigs running in 1991 averaged 862.8, a 14.4% drop below the 1990 activity level of 1007.8 rigs. The rig count, began at 1,068 in January, but fell steadily for the remainder of the year. A brief upturn at mid-year failed to hold up and the year-end increases in drilling we had come to expect since 1986 never materialized.

Not Available

1992-02-01T23:59:59.000Z

20

Rotary power slips  

SciTech Connect

This patent describes rotary power slips, for use in the rotary table of an earth drilling rig, comprising: a body; slip means carried on the body for gripping and releasing pipe in a pipe opening in a rotary table; a stationary air transfer ring supported by the body, and having a primary fluid conduit for connection to a stationary fluid source on the drilling rig, and having a transverse upper surface with at least two concentric grooves; an annular seal ring secured to the body and having a transverse lower surface and an air passageway; expansive means including an expansive ring having inner and outer edges mounted in the grooves on the upper surface of the air transfer ring and cooperative with the lower surface of the seal ring for forming an annular expansive fluid duct to conduct fluid between the primary fluid conduit and the air passageway; a fluid cylinder mounted on the body and fluidly connected to a secondary fluid conduit through the body to the air passageway for raising and lowering the slip means in response to fluid flow through the primary fluid conduit, the air passageway, and the secondary fluid conduit; and a retainer ring in each of the grooves on the upper surface of the air transfer ring, compressed against one of the edges of the expansive ring for locking the expansive ring in place.

Crowe, W.E.

1987-07-21T23:59:59.000Z

Note: This page contains sample records for the topic "indicators rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Earth drill rig  

SciTech Connect

This patent describes an earth drill rig wherein an upwardly and downwardly moving drill-string-turning rotary table is rotated by a kelly bar connected at its lower end to a vertical drive shaft, the kelly bar being journalled for rotation in and fixed against axial movement with respect to a drill frame assembly and the rotary table being mounted for axial movement on and along the drill frame assembly. The drill frame assembly is pivotally mounted on a vehicle on a substantially horizontal axis for pivoting between an upright position and a substantially horizontal position for transportation. The improvement described here comprises the drill frame assembly pivot axis positioned below the lower end of the kelly bar and above the upper end of the vertical drive shaft, and a universal coupling connecting the lower end of the kelly bar and the vertical drive shaft the universal coupling comprising universal joints at opposite ends of an elongated slip joint connector and connected there-by for relative axial movement but driving coupling between the universal joints. The universal joints lie generally on a circle of which the drill frame assembly pivot axis is the center. The drill frame assembly can be moved between the upright and the substantially horizontal positions without disconnecting the kelly bar from the vertical drive shaft, the kelly bar being revolvable by the drive shaft through substantially the entire range of movement of the drill frame assembly.

Rassieur, C.L.

1987-01-27T23:59:59.000Z

22

Electricity on the rig; part I -- electric applications on drilling and workover rigs  

SciTech Connect

This article points out that not only have electric motors replaced diesel engines and mechanical transmissions, but solid-state equipment is rapidly taking the place of rotary equipment in variable speed drivers and control systems. The SCR (silicon controlled rectifier) type of speed control has replaced other types by a large margin of acceptance on drilling rigs and has begun to be used on workover and service rigs. In most cases, electrical power is generated at the rig site with diesel-AC generators. On mechanically driven rigs, single diesel-generator sets operate to supply power for lighting and electrical motor loads. When high levels of power are required, such as on SCR-powered rigs, multiple generators are operated in electrical-parallel and each contributes to the total power required.

McNair, W.L.

1983-03-01T23:59:59.000Z

23

Workover well control. Part 3. Conventional rigs, snubbing units handle a variety of workover jobs  

SciTech Connect

The conventional rig, the most widely used rig for workovers, performs several common functions: tripping in and out of the hole, rotating the work string, and circulating fluid. Its primary component groups are the derrick, hoisting systems, rotary tools, circulating systems, and tubular goods. Rig sizing depends on the job requirements; the typical workover rig is a small-capacity, single unit used for concentric work. A workover rig's most important feature is its portability; compartmentalizing the rig permits transporting it offshore in packages smaller than 8000 lb and allows small cranes to replace derrick barges for loading operations.

Adams, N.

1981-08-31T23:59:59.000Z

24

40th annual Reed rig census  

SciTech Connect

This paper reports that declines characterize the 1992 rig census-in the number of available drilling rigs, in the number of active rigs, in rig utilization rate, in the number of rig owners and in industry optimism. The number of rotary rigs available for U.S. drilling fell by 255 units (11.3%) during the past 12 months, an attrition rate almost four times greater than in 1991. But despite the high attrition, only 59.7% of remaining rigs were working during the time the census was taken. Results of the 1992 census bring emphasis to an industry trend that became apparent in early 1991. The major oil companies, and many independents, continued their exodus form the U.S., and the remaining independents, which were hurt by low natural gas prices and unfavorable tax treatment of intangible drilling costs, were not able to pick u the drilling slack. Consequently, the past year has been disastrous for many U.S. drilling contractors, and the outlook for this industry segment remains bleak.

Fitts, R.L.; Stokes, T.A. (Reed Tool Co., Houston, TX (United States))

1992-10-01T23:59:59.000Z

25

Four rigs refurbished for West Africa drilling  

SciTech Connect

In April and May 1990, Shell Petroleum Development Co. of Nigeria Ltd. awarded Noble Drilling West Africa Inc. four separate contracts to drill oil and gas wells in the inland waterways of Nigeria. The contracted rigs included a shallow water jack up, the NN-1, and three posted barges, the Gene Rosser, the Chuck Syring, and the Lewis Dugger. The jack up was built in 1978, and the three posted barges are 1980s vintage. Three of the rigs have been idle for a number of years. The Shell Nigeria contracts required major modifications to the rigs before putting them into international service. Noble replaced or refurbished all major pieces of equipment in the drilling, power, and service systems on the rigs. Rig crews serviced all other equipment. A significant amount of general service piping and electrical wiring was replaced. Each rig also required additional motor control centers to support the new drilling and mud processing equipment. Alfa-Laval waste-heat water desalination plants and new sewage treatment units were installed on all four rigs. Because of the tidal variances and high silt conditions expected in the African waterways, all engine cooling systems were converted from heat exchangers to radiators. Rotary tables were made common on all rigs at 37 1/2 in. Noble had all traveling equipment completely inspected and modified as necessary. Strict attention was paid to certification and documentation of all equipment. Safety upgrades conformed to both Shell and Noble standards. Fire and gas detection systems were installed throughout each rig. Water and foam deluge systems were installed in the wellhead areas, and new foam systems and monitors were installed on the helldecks.

Not Available

1991-06-10T23:59:59.000Z

26

Hoisting & Rigging Fundamentals  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Hoisting and Rigging Hoisting and Rigging Fundamentals for Riaaers and ODerators Pendant Control - Components TR244C, Rev. 5 December 2002 TR244C Rev . 5 TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii HOISTING AND RIGGING OBJECTIVES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 WIRE ROPE SLINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SYNTHETIC WEBBING SLINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I O CHAINSLINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 METAL MESH SLINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 SPREADER BEAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 RIGGING HARDWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

27

Soft torque rotary system reduces drillstring failures  

SciTech Connect

This paper reports that the use of the soft torque system has significantly reduced torque fluctuations (up to 80%), torsional drillstring vibrations, and bit slip-stick conditions to help reduce drillstring failures and improve penetration rates in deep directional wells. The system was instrumental in eliminating expensive ($5-10 million) drillstring failures on Well SL 531 No. 3, a complex directional well in Mobile Bay. The soft torque rotary system attenuates and interrupts the torsional oscillations of the drillstring and thus prevents the buildup of energy in torsional waves that are reflected back and forth between the bit and the rotary table. The soft torque rotary system can be installed on any rig equipped with an independent electronically driven rotary table or top drive. The system is relatively inexpensive and easy to install.

Javanmardi, K.; Gaspard, D. (Shell Offshore Inc., New Orleans, LA (United States))

1992-10-12T23:59:59.000Z

28

39th annual Reed rig census  

SciTech Connect

This paper reports on cutbacks in U.S. exploration and development drilling during the first half of 1991 which squeezed most of the optimism out of the drilling industry. Just how rough the year has been is underscored by the results of this year's rig census. The number of rotary rigs available for U.S. drilling declined by only 69 units (3%) during the past 12 months. But despite those withdrawals from competition, only 66% of the remaining rigs were working at the time the census was taken. Results of the 1991 census contrasted sharply with the stability and optimism that seemed apparent a year ago when 72% of the available rig fleet met the census definition of active. At that time, the mini-boom in horizontal drilling coupled with tax-credit- driven gas drilling led to a relatively high rig utilization rate and suggested that rig supply and demand might be close to an economically acceptable balance. However, it quickly became apparent in early 1991 that industry optimism was unjustified. Horizontal drilling began to drop and the lowest natural gas prices in 12 years triggered rapid declines in gas drilling. Although oil prices have been relatively stable and above $18 per bbl since January 1989, most major operators have concluded that a better return on investment can be had outside the U.S. and have drastically cut their domestic drilling budgets. These factors, combined with softened energy demand from the worldwide recession, further slowed U.S. drilling. The long awaited balance between rig supply and demand has seemingly slipped away. The 1991 Reed rig census describes an industry facing several more rough years. Details of this year's census include: The available U.S. fleet now stands at 2,251 rigs, down by 69 from the 2,320-unit total in 1990, and the lowest since 1976. Rigs meeting the census definition of active numbered 1,485, down 192 (11.4%) from the 1,677 active rigs counted a year earlier.

Crowhurst, M.E.; Fitts, R.L. (Reed Tool Co., Houston, TX (US))

1991-10-01T23:59:59.000Z

29

Hoisting & Rigging Assessment Form  

Energy.gov (U.S. Department of Energy (DOE))

  Assess the institutional and department/division hoisting and rigging (including forklift, overhead cranes small hoists, and mobile cranes) requirements, policies, procedures, and work practices...

30

Diverter/bop system and method for a bottom supported offshore drilling rig  

SciTech Connect

This patent describes a system adapted for alternative use as a diverter or a blowout preventer for a bottom supported drilling rig and adapted for positioning beneath a rotary table of the drilling rig, the system comprising: a fluid flow controller having a controller housing with a lower opening and an upper opening and a vertical flow path therebetween and an outlet passage provided in its housing wall, and at least two bases. A method is described for installing a system adapted for alternative connection as a diverter or a blowout preventer for a bottom supported drilling rig positioned beneath a rotary table of the drilling rig after structural casing has been set in a borehole. The method comprises: positioning a first telescoping spool having a lower end and an upper end below the rotary table, the first spool having a first base disposed at its upper end, the first base having a port disposed in its wall; aligning a fluid flow controller having a controller housing wall outlet passage and adapted for alternative use as a diverter or a blowout preventer so that the controller is substantially vertically aligned between a bore of the rotary table above and the structural casing below; and securing the fluid flow controller beneath the drilling rig rotary table.

Roche, J.R.; Alexander, G.G.

1987-03-03T23:59:59.000Z

31

Chapter 10 - RIGGING HARDWARE  

NLE Websites -- All DOE Office Websites (Extended Search)

ASME, DOERL-92-36 and the Rigging Hardware manufacturers' requirements. It is the responsibility of the user of this manual to implement all of the requirements from listed...

32

Rig Efficiency Paper  

Annual Energy Outlook 2012 (EIA)

"active" annual rig count which is an imprecise and subjective task. Baker Hughes, 5 Smith, 6 ReedHycalog (Now NOV), 7 Schlumberger, 8 and IADC 9 publicly report the number of...

33

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DOE-STD-1090-2011 DOE-STD-1090-2011 September 2011 Superseding DOE-STD-1090-2007 August 2007 DOE STANDARD HOISTING AND RIGGING U.S. Department of Energy AREA SAFT Washington, D.C. 20585 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. INCH-POUND INTENTIONALLY BLANK DOE-STD-1090-2011 iii Introduction The U.S. Department of Energy (DOE) Hoisting and Rigging Standard is intended to be used by supervisors, line managers, safety personnel, equipment operators, riggers and other personnel responsible for the safety of hoisting and rigging operations at DOE sites. It may be used as either contract document or as a best practices guide at the site's or program office's discretion. The standard invokes applicable OSHA and national consensus standards but also delineates

34

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

13-i CHAPTER 13 LOAD HOOKS This chapter provides safety standards for the inspection, testing, and maintenance of load hooks installed on cranes or hoists and implements the requirements of ASME B30.10, Chapter 10-1, "Hooks." See Chapter 12, "Rigging Accessories," for rigging hook requirements (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). 13.1 GENERAL ...............................................................................................................................13-1 13.1.1 Marking......................................................................................................................13-1 13.1.2 Attachments ...............................................................................................................13-1

35

Design of a bicycle rig  

E-Print Network (OSTI)

A design of a bicycle (bike) rig was conducted. This bike rig is designed to be used for aerodynamics measurement testing of bicycles, cyclists and cycling related items in a wind tunnel. This paper discusses the design ...

Racz, Rastislav

2010-01-01T23:59:59.000Z

36

Field Demonstraton of Existing Microhole Coiled Tubing Rig (MCTR) Technology  

SciTech Connect

The performance of an advanced Microhole Coiled Tubing Rig (MCTR) has been measured in the field during the drilling of 25 test wells in the Niobrara formation of Western Kansas and Eastern Colorado. The coiled tubing (CT) rig designed, built and operated by Advanced Drilling Technologies (ADT), was documented in its performance by GTI staff in the course of drilling wells ranging in depth from 500 to nearly 3,000 feet. Access to well sites in the Niobrara for documenting CT rig performance was provided by Rosewood Resources of Arlington, VA. The ADT CT rig was selected for field performance evaluation because it is one of the most advanced commercial CT rig designs that demonstrate a high degree of process integration and ease of set-up and operation. Employing an information collection protocol, data was collected from the ADT CT rig during 25 drilling events that encompassed a wide range of depths and drilling conditions in the Niobrara. Information collected included time-function data, selected parametric information indicating CT rig operational conditions, staffing levels, and field observations of the CT rig in each phase of operation, from rig up to rig down. The data obtained in this field evaluation indicates that the ADT CT rig exhibited excellent performance in the drilling and completion of more than 25 wells in the Niobrara under varied drilling depths and formation conditions. In the majority of the 25 project well drilling events, ROP values ranged between 300 and 620 feet per hour. For all but the lowest 2 wells, ROP values averaged approximately 400 feet per hour, representing an excellent drilling capability. Most wells of depths between 500 and 2,000 feet were drilled at a total functional rig time of less than 16 hours; for wells as deep at 2,500 to 3,000 feet, the total rig time for the CT unit is usually well under one day. About 40-55 percent of the functional rig time is divided evenly between drilling and casing/cementing. The balance of time is divided among the remaining four functions of rig up/rig down, logging, lay down bottomhole assembly, and pick up bottomhole assembly. Observations made during all phases of CT rig operation at each of the project well installations have verified a number of characteristics of the technology that represent advantages that can produce significant savings of 25-35 percent per well. Attributes of the CT rig performance include: (1) Excellent hole quality with hole deviation amounting to 1-2 degrees; (2) Reduced need for auxiliary equipment; (3) Efficient rig mobilization requiring only four trailers; (4) Capability of ''Zero Discharge'' operation; (5) Improved safety; and, (6) Measurement while drilling capability. In addition, commercial cost data indicates that the CT rig reduces drilling costs by 25 to 35% compared to conventional drilling technology. Widespread commercial use of the Microhole Coiled Tubing technology in the United States for onshore Lower-48 drilling has the potential of achieving substantially positive impacts in terms of savings to the industry and resource expansion. Successfully commercialized Microhole CT Rig Technology is projected to achieve cumulative savings in Lower-48 onshore drilling expenditures of approximately 6.8 billion dollars by 2025. The reduced cost of CT microhole drilling is projected to enable the development of gas resources that would not have been economic with conventional methods. Because of the reduced cost of drilling achieved with CT rig technology, it is estimated that an additional 22 Tcf of gas resource will become economic to develop. In the future, the Microhole Coiled Tubing Rig represents an important platform for the continued improvement of drilling that draws on a new generation of various technologies to achieve goals of improved drilling cost and reduced impact to the environment.

Kent Perry; Samih Batarseh; Sheriff Gowelly; Thomas Hayes

2006-05-09T23:59:59.000Z

37

U. S. rig count drops below 600, a post-1940 low  

SciTech Connect

This paper reports that the Baker Hughes Inc. count of active U.S. rotary rigs as of June 12 fell to less than 600 the first time since that tally began in 1940. The previous modern record low was set at 610 the previous week. Baker Hughes reported about 1,400 rigs idle in the U.S. last week. Using a different criteria, the Smith International count of U.S. active rigs fell seven units to 653 the week ended June 12, compared with a count of 910 the previous year. Baker Hughes predecessor Hughes Tool Co. began keeping monthly records of active U.S. rigs in January 1940. The lowest monthly count that year was 857. It changed to a weekly count in January 1949. The milestone was met wit calls for relief for the U.S. upstream sector from industry and government officials in Washington.

Not Available

1992-06-22T23:59:59.000Z

38

Rotary filtration system  

DOE Patents (OSTI)

A rotary filtration apparatus for filtering a feed fluid into permeate is provided. The rotary filtration apparatus includes a container that has a feed fluid inlet. A shaft is at least partially disposed in the container and has a passageway for the transport of permeate. A disk stack made of a plurality of filtration disks is mounted onto the shaft so that rotation of the shaft causes rotation of the filtration disks. The filtration disks may be made of steel components and may be welded together. The shaft may penetrate a filtering section of the container at a single location. The rotary filtration apparatus may also incorporate a bellows seal to prevent leakage along the shaft, and an around the shaft union rotary joint to allow for removal of permeate. Various components of the rotary filtration apparatus may be removed as a single assembly.

Herman, David T. (Aiken, SC); Maxwell, David N. (Aiken, SC)

2011-04-19T23:59:59.000Z

39

Hoisting & Rigging Assessment Plan  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

HOISTING & RIGGING HOISTING & RIGGING Assessment Plan NNSA/Nevada Site Office Facility Representative Division Performance Objective: To determine that hoisting and rigging operations are conducted according to "industry best standards" for increasing equipment reliability while assuring worker safety, and to verify issues being addressed in BN Hoisting assessment. Criteria: Lifts are identified and categorized appropriately for scheduled maintenance. DOE-STD-1090-2001 An integrated process ensures safety issues are identified and controls established. DOE-STD-1090-2001 Personnel operating and maintaining the hoisting equipment are trained; they understand their roles and responsibilities. DOE-STD-1090-2001 Maintenance conducts safety inspections of hoisting and rigging

40

Hoisting & Rigging Assessment Plan  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

HOISTING & RIGGING HOISTING & RIGGING Assessment Plan NNSA/Nevada Site Office Facility Representative Division Performance Objective: To determine that hoisting and rigging operations are conducted according to "industry best standards" for increasing equipment reliability while assuring worker safety, and to verify issues being addressed in BN Hoisting assessment. Criteria: Lifts are identified and categorized appropriately for scheduled maintenance. DOE-STD-1090-2001 An integrated process ensures safety issues are identified and controls established. DOE-STD-1090-2001 Personnel operating and maintaining the hoisting equipment are trained; they understand their roles and responsibilities. DOE-STD-1090-2001 Maintenance conducts safety inspections of hoisting and rigging

Note: This page contains sample records for the topic "indicators rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1-i 1-i CHAPTER 11 WIRE ROPE AND SLINGS This chapter provides requirements for the fabrication and use of wire rope and slings used in hoisting and rigging and implements the requirements of ASME B30.9, Slings (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). . 11.1 GENERAL ...............................................................................................................................11-1 11.2 WIRE ROPE ............................................................................................................................11-4 11.2.1 Wire-Rope Lays .........................................................................................................11-4 11.2.2 Wire-Rope Cores .......................................................................................................11-4

42

U. S. S. R. turbodrilling ROP exceeds U. S. rotary rate  

SciTech Connect

It is common practice in the U.S.S.R. to evaluate drilling estimates by a mere comparison of the footage drilled on a per-rig, per-month basis because the figure integrates the techniques, technology, and management used. According to this approach, the rate of penetration (ROP) in the U.S.S.R. is 2.3-2.8 times less than that in the U.S. Based on the statistics published in the Neftanaya Promyishlennost annual, in 1988 the average rotary drilling rate in the U.S. was 4,404 m (14,440 ft)/rig/month (this figure in the U.S. annual footage drilled by all rotary rigs divided by the annual average rig count and converted from yearly to monthly figures), and in the U.S.S.R. it was 1,595 m (5,233 ft)/rig/month. This type of comparison is misleading because the drilling areas in the two countries differ greatly in geographic, geologic, and climatic characteristics. The same holds true for comparisons of average well depths. The preceeding characteristics influence drilling estimates differently. The most difficult task is to evaluate these factors as an average in each country. Our approach to the comparison takes into account only the average footage drilled for each country. In the U.S.S.R. more than 85% of the wells are drilled with turbodrills, and in the U.S. most wells (approximately 80%) are rotary drilled.

Pogarskiy, A.A.; Yasashin, A.M. (All Union Scientific and Research Inst. for Organization, Management, and Economics of Oil and Gas Industry, Moscow (SU))

1991-06-03T23:59:59.000Z

43

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 4 BELOW-THE-HOOK LIFTING DEVICES 14-i This chapter provides the requirements for below-the-hook lifting devices used in hoisting and rigging, such as spreader bars, lifting yokes, and lift fixtures. This section implements the requirements of ASME B30.20, "Below-the-Hook Lifting Devices" (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). NOTE: Special lifting devices for shipping containers weighing 10,000 lb or more that are used for radioactive materials are governed by ANSI N14.6 ["Standard for Special Lifting Devices for Shipping Containers Weighing 10,000 Pounds (4,500 kg) or More for Nuclear Materials."] 14.1 GENERAL ...............................................................................................................................14-1

44

Electricity on the rig. Part 3 - New electric rig technology  

SciTech Connect

The use of an SCR-controlled power system on an offshore drilling rig has lead to an increased acceptance of high technology equipment. Such equipment increases drilling productivity, reduces maintenance, and improves reliability. Most new rigs now have AC squirrel cage motors, brushless AC generators, silicon controlled rectifiers, DC motors, and swtichgear and motor starters. Several opportunities for cost reductions in SCR systems, such as improving the power factor, are studied in this paper.

McNair, W.L.

1983-07-01T23:59:59.000Z

45

Solar stirling engine rig tests  

Science Journals Connector (OSTI)

A description of a prototype four-cylinder Stirli ng engine construction with the heat receiver of the concentrated solar radiant flux and with a swashplate drive is given. The rig tests have been carried out ...

I. A. Tursunbaev; E. P. Orda; A. I. Lezhebokov; A. P. Korobkov…

2010-11-01T23:59:59.000Z

46

Rotary mechanical latch  

DOE Patents (OSTI)

A rotary mechanical latch for positive latching and unlatching of a rotary device with a latchable rotating assembly having a latching gear that can be driven to latched and unlatched states by a drive mechanism such as an electric motor. A cam arm affixed to the latching gear interfaces with leading and trailing latch cams affixed to a flange within the drive mechanism. The interaction of the cam arm with leading and trailing latch cams prevents rotation of the rotating assembly by external forces such as those due to vibration or tampering.

Spletzer, Barry L.; Martinez, Michael A.; Marron, Lisa C.

2012-11-13T23:59:59.000Z

47

Rotary shaft sealing assembly  

DOE Patents (OSTI)

A rotary shaft sealing assembly in which a first fluid is partitioned from a second fluid in a housing assembly having a rotary shaft located at least partially within. In one embodiment a lip seal is lubricated and flushed with a pressure-generating seal ring preferably having an angled diverting feature. The pressure-generating seal ring and a hydrodynamic seal may be used to define a lubricant-filled region with each of the seals having hydrodynamic inlets facing the lubricant-filled region. Another aspect of the sealing assembly is having a seal to contain pressurized lubricant while withstanding high rotary speeds. Another rotary shaft sealing assembly embodiment includes a lubricant supply providing a lubricant at an elevated pressure to a region between a lip seal and a hydrodynamic seal with a flow control regulating the flow of lubricant past the lip seal. The hydrodynamic seal may include an energizer element having a modulus of elasticity greater than the modulus of elasticity of a sealing lip of the hydrodynamic seal.

Dietle, Lannie L; Schroeder, John E; Kalsi, Manmohan S; Alvarez, Patricio D

2013-08-13T23:59:59.000Z

48

Rotary magnetic heat pump  

DOE Patents (OSTI)

A rotary magnetic heat pump constructed without flow seals or segmented rotor accomplishes recuperation and regeneration by using split flow paths. Heat exchange fluid pumped through heat exchangers and returned to the heat pump splits into two flow components: one flowing counter to the rotor rotation and one flowing with the rotation. 5 figs.

Kirol, L.D.

1987-02-11T23:59:59.000Z

49

Rotary Burner Demonstration  

SciTech Connect

The subject technology, the Calcpos Rotary Burner (CRB), is a burner that is proposed to reduce energy consumption and emission levels in comparison to currently available technology. burners are used throughout industry to produce the heat that is required during the refining process. Refineries seek to minimize the use of energy in refining while still meeting EPA regulations for emissions.

Paul Flanagan

2003-04-30T23:59:59.000Z

50

Ultrasonic Rayleigh wave inspection of unit train rotary couplers  

E-Print Network (OSTI)

of using ultrasonic Rayleigh waves I' or the inspection of rotary couplers 'O'. Experiments rvere conducted on three couplers, one that was cracked, one that was nerv, and one new coupler with simulated cracks. IJsing a commercial probe. indications... of using ultrasonic Rayleigh waves I' or the inspection of rotary couplers 'O'. Experiments rvere conducted on three couplers, one that was cracked, one that was nerv, and one new coupler with simulated cracks. IJsing a commercial probe. indications...

Salkowski, Charles Leo

2012-06-07T23:59:59.000Z

51

Chapter Three - Rotary Seals  

Science Journals Connector (OSTI)

This chapter discusses the range of rotary seals available that can be applied across a range of industries. The basic operation, key design features and the many potential variants of rotary-shaft lip seals are discussed, plus plastic seals that can be used to extend the performance envelope. Variants that may be used for exclusion of contaminant and alternative designs of elastomer and plastic seals, some of which can be used at high pressures in specialized applications, are covered. The basic design and operation of mechanical seals are discussed. The differences in seal designs covering the range from domestic goods and automotive through process plant to turbo machinery are covered. The key features of compression packing and modern material options are presented. A wide range of other seal types are also used in rotating machinery, particularly in high-speed turbo machinery. Current developments for a number of seal types, labyrinth, honeycomb, leaf seals, brush seals and viscoseals, are summarized.

Robert Flitney

2014-01-01T23:59:59.000Z

52

Recirculating rotary gas compressor  

DOE Patents (OSTI)

A positive displacement, recirculating Roots-type rotary gas compressor is described which operates on the basis of flow work compression. The compressor includes a pair of large diameter recirculation conduits which return compressed discharge gas to the compressor housing, where it is mixed with low pressure inlet gas, thereby minimizing adiabatic heating of the gas. The compressor includes a pair of involutely lobed impellers and an associated port configuration which together result in uninterrupted flow of recirculation gas. The large diameter recirculation conduits equalize gas flow velocities within the compressor and minimize gas flow losses. The compressor is particularly suited to applications requiring sustained operation at higher gas compression ratios than have previously been feasible with rotary pumps, and is particularly applicable to refrigeration or other applications requiring condensation of a vapor. 12 figs.

Weinbrecht, J.F.

1992-02-25T23:59:59.000Z

53

Recirculating rotary gas compressor  

DOE Patents (OSTI)

A positive displacement, recirculating Roots-type rotary gas compressor which operates on the basis of flow work compression. The compressor includes a pair of large diameter recirculation conduits (24 and 26) which return compressed discharge gas to the compressor housing (14), where it is mixed with low pressure inlet gas, thereby minimizing adiabatic heating of the gas. The compressor includes a pair of involutely lobed impellers (10 and 12) and an associated port configuration which together result in uninterrupted flow of recirculation gas. The large diameter recirculation conduits equalize gas flow velocities within the compressor and minimize gas flow losses. The compressor is particularly suited to applications requiring sustained operation at higher gas compression ratios than have previously been feasible with rotary pumps, and is particularly applicable to refrigeration or other applications requiring condensation of a vapor.

Weinbrecht, John F. (601 Oakwood Loop, NE., Albuquerque, NM 87123)

1992-01-01T23:59:59.000Z

54

Hoisting and Rigging Technical Advisory Committee  

Energy.gov (U.S. Department of Energy (DOE))

The Hoisting and Rigging Technical Advisory Committee serves as an advisory body to the Office of Health, Safety and Security (HSS) by providing support to their policy efforts aimed at ensuring the safe performance of hoisting and rigging activities at DOE facilities and in the review and resolution of identified generic hoisting and rigging safety issues.

55

Diverter bop system and method for a bottom supported offshore drilling rig  

SciTech Connect

A system and method for installing a fluid flow controller and telescoping spools beneath an offshore bottom supported drilling rig rotary table is disclosed. Upper and lower telescoping spools are provided for initially connecting a Diverter/BOP convertible fluid flow controller between structural casing in the well and a permanent housing beneath the drilling rig rotary table. Clamp means are provided for clamping the rig vent line to an opening in the housing wall of the fluid flow controller during drilling of the borehole through the structural casing in preparation for setting and cementing the conductor casing. In that mode, the system is adapted as a diverter system. After the well is drilled for the conductor casing and the conductor casing is cemented and cut off at its top, a mandrel is fitted at the top of the conductor casing to which the lower end of the lower spool may be connected. The system may be used in this configuration as a diverter system, or after removal of the vent line and connection of a kill line to the housing outlet, the system may be used as a low pressure blowout preventer system.

Roche, J. R.; Alexander, G. G.; Carbaugh, W. L.

1985-06-25T23:59:59.000Z

56

Hoisting & Rigging Lift Plan  

NLE Websites -- All DOE Office Websites (Extended Search)

Hoisting & Rigging Lift Plan Hoisting & Rigging Lift Plan Stanford Synchrotron Radiation Laboratory May 16, 2005 SSRL-HRLP-000-R0 Page 1 of 3 General Information Lift Plan Document # Plan prepared by: Describe the load or items to be lifted: Could the load, if dropped, release hazardous materials or radioactivity? No Yes (describe) Is the load irreplaceable or would it be very costly to replace if damaged? No Yes (describe) Brief description of lift activities (specify if rolling or flipping involved) Equipment Information Equipment ID: Equipment custodian: Rated capacity: Operator capacity : Personnel Protective Equipment (PPE) Steel-toed shoes Required for all personnel involved with lift activity to protect from crushing of feet/toes

57

Risk analysis of jackup rigs  

Science Journals Connector (OSTI)

Increasing attention has been focussed in the North Sea and elsewhere on the quantification of the risks of working in a hazardous enviroment: the offshore world. The perception of risk with respect to mobile rigs has often been vague and uninformed. This paper attempts to put the risks with respect to jackup rigs into perspective by quantifying them and comparing them to other risks. This paper contains a few risk comparisons with fixed platforms, semi-submersibles, and drillships. Historical casualties are used in an example to show how a change intended to make an operation safer, may result in the opposite effect. Examining risks from losses due to environmental overload, the conclusion is reached that jackups are very safe structures: there appears to be no jackup, in the timeframe examined, that has been lost because of a deficiency in the calculation methods currently in use by knowledgeable experts.

B.P.M. Sharples; W.T. Bennett Jr; J.C. Trickey

1989-01-01T23:59:59.000Z

58

Rotary shaft seal  

DOE Patents (OSTI)

The invention is a novel rotary shaft seal assembly which provides positive-contact sealing when the shaft is not rotated and which operates with its sealing surfaces separated by a film of compressed ambient gas whose width is independent of the speed of shaft rotation. In a preferred embodiment, the assembly includes a disc affixed to the shaft for rotation therewith. Axially movable, non-rotatable plates respectively supported by sealing bellows are positioned on either side of the disc to be in sealing engagement therewith. Each plate carries piezoelectric transducer elements which are electrically energized at startup to produce films of compressed ambient gas between the confronting surfaces of the plates and the disc. Following shutdown of the shaft, the transducer elements are de-energized. A control circuit responds to incipient rubbing between the plate and either disc by altering the electrical input to the transducer elements to eliminate rubbing.

Langebrake, Clair O. (Waverly, OH)

1984-01-01T23:59:59.000Z

59

Rotary shaft seal  

DOE Patents (OSTI)

The invention is a novel rotary shaft seal assembly which provides positive-contact sealing when the shaft is not rotated and which operates with its sealing surfaces separated by a film of compressed ambient gas whose width is independent of the speed of shaft rotation. In a preferred embodiment, the assembly includes a disc affixed to the shaft for rotation therewith. Axially movable, non-rotatable plates respectively supported by sealing bellows are positioned on either side of the disc to be in sealing engagement therewith. Each plate carries piezoelectric transucer elements which are electrically energized at startup to produce films of compressed ambient gas between the confronting surfaces of the plates and the disc. Following shutdown of the shaft, the transducer elements are de-energized. A control circuit responds to incipient rubbing between the plate and either disc by altering the electrical input to the transducer elements to eliminate rubbing.

Langebrake, C.O.

1984-01-01T23:59:59.000Z

60

Rotary kiln seal  

SciTech Connect

A rotary seal used to prevent the escape of contaminates from a rotating kiln incinerator. The rotating seal combines a rotating disc plate which is attached to the rotating kiln shell and four sets of non-rotating carbon seal bars housed in a primary and secondary housing and which rub on the sides of the disc. A seal air system is used to create a positive pressure in a chamber between the primary and secondary seals to create a positive air flow into the contaminated gas chamber. The seal air system also employs an air inlet located between the secondary and tertiary seals to further insure that no contaminates pass the seal and enter the external environment and to provide makeup air for the air which flows into the contaminated gas chamber. The pressure exerted by the seal bars on the rotating disc is controlled by means of a preload spring. The seal is capable of operating in a thermally changing environment where the both radial expansion and axial movement of the rotating kiln do not result in the failure of the seal.

Drexler, Robert L. (Idaho Falls, ID)

1992-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "indicators rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5 5 CONSTRUCTION HOISTING AND RIGGING EQUIPMENT REQUIREMENTS 15-i Chapter 15 Construction Hoisting and Rigging Equipment Requirements This chapter outlines the requirements for the safe use of hoisting and rigging equipment on construction projects at DOE installations. 15.1 GENERAL ...............................................................................................................................15-1 15.2 PERSONNEL QUALIFICATIONS.........................................................................................15-2 15.2.1 Qualified Operators of Mobile Cranes.......................................................................15-2 15.2.2 Qualified Operators of Forklift Trucks ......................................................................15-3

62

Solar-heated rotary kiln  

DOE Patents (OSTI)

A solar heated rotary kiln utilized for decomposition of materials, such as zinc sulfate is disclosed. The rotary kiln has an open end and is enclosed in a sealed container having a window positioned for directing solar energy into the open end of the kiln. The material to be decomposed is directed through the container into the kiln by a feed tube. The container is also provided with an outlet for exhaust gases and an outlet for spent solids, and rests on a tiltable base. The window may be cooled and kept clear of debris by coolant gases.

Shell, P.K.

1982-04-14T23:59:59.000Z

63

Group Based Rigging of Realistically Feathered Wings  

E-Print Network (OSTI)

for feather interpenetration resulting from movement from extended to folded wing poses [Hiebert 3 et al. 2006]. The rigging method developed for this thesis provides a single rig and control solution for animation that includes both outstretched... be highly detailed and as anatomically accurate as a mythical creature can be. A big challenge to this was the look and actions of the feathers [Hiebert et al. 2006]. The feathers on the gryphons (coverts, and body feathers) were generated procedurally...

Howard, Heather Vernette

2012-02-14T23:59:59.000Z

64

Computational experience with a three-dimensional rotary engine combustion model  

SciTech Connect

A new computer code was developed to analyze the chemically reactive flow and spray combustion processes occurring inside a stratified-charge rotary engine. Mathematical and numerical details of the new code were recently described by the present authors. The results are presented of limited, initial computational trials as a first step in a long-term assessment/validation process. The engine configuration studied was chosen to approximate existing rotary engine flow visualization and hot firing test rigs. Typical results include: (1) pressure and temperature histories, (2) torque generated by the nonuniform pressure distribution within the chamber, (3) energy release rates, and (4) various flow-related phenomena. These are discussed and compared with other predictions reported in the literature. The adequacy or need for improvement in the spray/combustion models and the need for incorporating an appropriate turbulence model are also discussed.

Raju, M.S.; Willis, E.A.

1990-04-01T23:59:59.000Z

65

Regenerative rotary displacer Stirling engine  

SciTech Connect

A few rotary displacer Stirling engines in which the displacer has one gas pocket space at one side and rotates in a main enclosed cylinder, which is heated from one side and cooled from opposite side without any regenerator, have been studied for some time by the authors. The authors tried to improve this engine by equipping it with a regenerator, because without a regenerator, pressure oscillation and efficiency are too small. Here, several types of regenerative rotary displacer piston Stirling engines are proposed. One is the contra-rotating tandem two disc type displacer engine using axial heat conduction through side walls or by heat pipes and another is a single disc type with circulating fluid regenerator or heat pipes. Stirling engines of this new rotary displacer type are thought to attain high speed. Here, experimental results of the original rotary displacer Stirling engine without a regenerator, and one contra-rotating tandem displacer engine with side wall regenerator by axial heat conduction are reported accompanied with a discussion of the results.

Isshiki, Naotsugu; Watanabe, Hiroichi [Nihon Univ. Tokyo (Japan); Raggi, L. [Waseda Univ., Tokyo (Japan); Isshiki, Seita; Hirata, Koichi

1996-12-31T23:59:59.000Z

66

U.S. Crude Oil Rotary Rigs in Operation (Number of Elements)  

Gasoline and Diesel Fuel Update (EIA)

Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1973 NA NA NA NA NA NA NA NA NA NA NA NA 1974 NA NA NA NA NA NA NA NA NA NA NA NA 1975 NA NA NA NA NA NA NA NA NA NA NA NA 1976...

67

U.S. Natural Gas Rotary Rigs in Operation (Number of Elements...  

Gasoline and Diesel Fuel Update (EIA)

Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1970's NA NA NA NA NA NA NA 1980's NA NA NA NA NA NA NA NA 354 401 1990's 464 351 331 364 427 385 464...

68

U.S. Onshore Crude Oil and Natural Gas Rotary Rigs in Operation...  

Gasoline and Diesel Fuel Update (EIA)

Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1973 1,120 1,037 959 914 974 1,042 1,075 1,140 1,183 1,250 1,304 1,318 1974 1,283 1,264 1,272 1,280 1,319 1,342 1,387 1,426...

69

U.S. Crude Oil Rotary Rigs in Operation (Number of Elements)  

Annual Energy Outlook 2012 (EIA)

Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1970's NA NA NA NA NA NA NA 1980's NA NA NA NA NA NA NA NA 554 453 1990's 532 482 373 373 335 323 306...

70

U.S. Natural Gas Rotary Rigs in Operation (Number of Elements...  

Gasoline and Diesel Fuel Update (EIA)

Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1973 NA NA NA NA NA NA NA NA NA NA NA NA 1974 NA NA NA NA NA NA NA NA NA NA NA NA 1975 NA NA NA NA NA NA NA NA NA NA NA NA 1976...

71

U.S. Crude Oil and Natural Gas Rotary Rigs in Operation (Number...  

Annual Energy Outlook 2012 (EIA)

Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1973 1,219 1,126 1,049 993 1,046 1,118 1,156 1,222 1,266 1,334 1,390 1,405 1974 1,372 1,355 1,367 1,381 1,413 1,432 1,480 1,518...

72

U.S. Offshore Crude Oil and Natural Gas Rotary Rigs in Operation...  

Annual Energy Outlook 2012 (EIA)

Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec 1973 99 89 90 79 72 76 81 82 83 84 86 87 1974 89 91 95 101 94 90 93 92 90 91 99 103 1975 94 93 102 102 102 106 109 112 113 112...

73

U.S. Crude Oil and Natural Gas Rotary Rigs in Operation (Number...  

Gasoline and Diesel Fuel Update (EIA)

Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1940's 2,017 1950's 2,154 2,543 2,641 2,613 2,508 2,686 2,620 2,426 1,922 2,071 1960's 1,748 1,761...

74

U.S. Onshore Crude Oil and Natural Gas Rotary Rigs in Operation...  

Annual Energy Outlook 2012 (EIA)

Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1940's NA 1950's NA NA NA NA NA NA NA NA NA NA 1960's NA NA NA NA NA NA NA NA NA NA 1970's NA NA NA...

75

U.S. Offshore Crude Oil and Natural Gas Rotary Rigs in Operation...  

Annual Energy Outlook 2012 (EIA)

Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 1940's NA 1950's NA NA NA NA NA NA NA NA NA NA 1960's NA NA NA NA NA NA NA NA NA NA 1970's NA NA NA 84...

76

Odessa fabricator builds rig specifically for geothermal drilling  

Energy.gov (U.S. Department of Energy (DOE))

For 35 years, MD Cowan has built drilling rigs, developing a market for its Super Single® rig for use in the nation's oil and gas fields. Now the Odessa-based company is branching out into alternative energy.

77

Rotary mode system initial instrument calibration  

SciTech Connect

The attached report contains the vendor calibration procedures used for the initial instrument calibration of the rotary core sampling equipment. The procedures are from approved vendor information files.

Johns, B.R.

1994-10-01T23:59:59.000Z

78

Rotary kilns - transport phenomena and transport processes  

SciTech Connect

Rotary kilns and rotating industrial drying ovens are used for a wide variety of applications including processing raw minerals and feedstocks as well as heat-treating hazardous wastes. They are particularly critical in the manufacture of Portland cement. Their design and operation is critical to their efficient usage, which if done incorrectly can result in improperly treated materials and excessive, high fuel costs. This book treats all engineering aspects of rotary kilns, including thermal and fluid principles involved in their operation, as well as how to properly design an engineering process that uses rotary kilns. Chapter 1: The Rotary Kiln Evolution and Phenomenon Chapter 2: Basic Description of Rotary Kiln Operation Chapter 3: Freeboard Aerodynamic Phenomena Chapter 4: Granular Flows in Rotary Kilns Chapter 5: Mixing and Segregation Chapter 6: Combustion and Flame - includes section on types of fuels used in rotary kilns, coal types, ranking and analysis, petroleum coke combustion, scrap tire combustion, pulverized fuel (coal/coke) firing in kilns, pulverized fuel delivery and firing systems. Chapter 7: Freeboard Heat Transfer Chapter 8: Heat Transfer Processes in the Rotary Kiln Bed Chapter 9: Mass and Energy Balance Chapter 10: Rotary Kiln Minerals Process Applications.

Boateng, A.

2008-01-15T23:59:59.000Z

79

Oil-spill aftermath hampers rig research  

Science Journals Connector (OSTI)

... Mexico, scientists say that they have been struggling to gain access to the region's rigs and drill ships, hampering their research. Marine scientists have long been allowed to install ... ships, hampering their research. Marine scientists have long been allowed to install instruments on offshore structures. The equipment can deliver vital data that would not be practical to gather ...

Melissa Gaskill

2011-07-04T23:59:59.000Z

80

DOE-STD-1090-99; DOE Standard Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

NLE Websites -- All DOE Office Websites (Extended Search)

TS TS INCH-POUND DOE-STD-1090-99 March 1999 Superseding DOE-STD-1090-96 September 1996 DOE STANDARD HOISTING AND RIGGING (Formerly Hoisting and Rigging Manual) U.S. Department of Energy AREA SAFT Washington, D.C. 20585 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. This document has been reproduced from the best available copy. Available to DOE and DOE contractors from ES&H Technical Information Services, U.S. Department of Energy, (800) 473-4375, fax: (301) 903-9823. Available to the public from the U.S. Department of Commerce, Technology Administration, National Technical Information Service, Springfield, VA 22161; (703) 605-6000. DOE STANDARD HOISTING AND RIGGING (Formerly Hoisting and Rigging Manual) Summary of Changes as of March 1999

Note: This page contains sample records for the topic "indicators rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5 5 CONSTRUCTION HOISTING AND RIGGING EQUIPMENT REQUIREMENTS 15-i This chapter outlines the requirements for the safe use of hoisting and rigging equipment on construction projects at DOE installations. 15.1 GENERAL ...............................................................................................................................15-1 15.2 PERSONNEL QUALIFICATIONS.........................................................................................15-2 15.2.1 Qualified Operators of Mobile Cranes.......................................................................15-2 15.2.2 Qualified Operators of Forklift Trucks ......................................................................15-3 15.2.3 Qualified Riggers .......................................................................................................15-4

82

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3 3 LOAD HOOKS 13-i Chapter 13 Load Hooks This chapter provides safety standards for the inspection, testing, and maintenance of load hooks installed on cranes or hoists and implements the requirements of ASME B30.10, Chapter 10-1, "Hooks." See Chapter 12, "Rigging Accessories," for rigging hook requirements. 13.1 GENERAL ...............................................................................................................................13-1 13.1.1 Marking......................................................................................................................13-1 13.1.2 Attachments ...............................................................................................................13-1

83

La Belle: rigging in the days of the spritsail topmast, a reconstruction of a seventeenth-century ship's rig  

E-Print Network (OSTI)

LA BELLE: RIGGING IN THE DAYS OF THE SPRITSAIL TOPMAST, A RECONSTRUCTION OF A SEVENTEENTH-CENTURY SHIP’S RIG A Thesis by CATHARINE LEIGH INBODY CORDER Submitted to the Office of Graduate Studies of Texas A&M University... in partial fulfillment of the requirements for the degree of MASTER OF ARTS December 2007 Major Subject: Anthropology LA BELLE: RIGGING IN THE DAYS OF THE SPRITSAIL TOPMAST, A RECONSTRUCTION OF A SEVENTEENTH-CENTURY SHIP’S RIG A...

Corder, Catharine Leigh Inbody

2008-10-10T23:59:59.000Z

84

La Belle: Rigging in the days of the spritsail topmast, a reconstruction of a seventeenth-century ship's rig  

E-Print Network (OSTI)

La Belle’s rigging assemblage has provided a rare and valuable source of knowledge of 17th-century rigging in general and in particular, French and small-ship rigging characteristics. With over 400 individual items including nearly 160 wood and iron...

Corder, Catharine Leigh Inbody

2009-05-15T23:59:59.000Z

85

Comparative analysis of core drilling and rotary drilling in volcanic terrane  

SciTech Connect

Initially, the goal of this report is to compare and contrast penetration rates of rotary-mud drilling and core drilling in young volcanic terranes. It is widely recognized that areas containing an abundance of recent volcanic rocks are excellent targets for geothermal resources. Exploration programs depend heavily upon reliable subsurface information, because surface geophysical methods may be ineffective, inconclusive, or both. Past exploration drilling programs have mainly relied upon rotary-mud rigs for virtually all drilling activity. Core-drilling became popular several years ago, because it could deal effectively with two major problems encountered in young volcanic terranes: very hard, abrasive rock and extreme difficulty in controlling loss of circulation. In addition to overcoming these difficulties, core-drilling produced subsurface samples (core) that defined lithostratigraphy, structure and fractures far better than drill-chips. It seemed that the only negative aspect of core drilling was cost. The cost-per-foot may be two to three times higher than an ''initial quote'' for rotary drilling. In addition, penetration rates for comparable rock-types are often much lower for coring operations. This report also seeks to identify the extent of wireline core drilling (core-drilling using wireline retrieval) as a geothermal exploration tool. 25 refs., 21 figs., 13 tabs.

Flynn, T.; Trexler, D.T.; Wallace, R.H. Jr. (ed.)

1987-04-01T23:59:59.000Z

86

Rigs to reefs: a petroleum industry perspective  

E-Print Network (OSTI)

, by implementing an ocean dumping program in conjunction with a rigs-to-reefs program, and through the development of new technology and methods to reduce transportation costs. Zn addition, the overall cost to industry participation can be reduced through... Environmental Enhancement and Fishing in the Seas (REEFS)" Task Force. This task force was comprised of representatives of federal and state government agencies, the oil and ocean industries, and the commercial and recreational fishing communities. Secretary...

Dubose, William Perry

1988-01-01T23:59:59.000Z

87

Open Rigging Through XML: Character Setup Utilizing Metadata and Node Based Editing  

E-Print Network (OSTI)

Manager. . . . . 22 7 The Rig Manager interface for an empty scene. . . . . . . . . . . . . . 23 8 The Rig Manager interface and “Rig Edit Mode” label on the viewport after clicking the “Create Rig” button. . . . . . . . . . . . . . . . . . . 24 9 The Rig... and replace them with code that performs the desired actions. For example, the node-based interface can be used to replace the task of authoring rig 6 definition files in a text editor so that the user never needs to learn the rig definition format. 7 3...

Kelly, Logan Scott

2014-02-19T23:59:59.000Z

88

Enclosed rotary disc air pulser  

DOE Patents (OSTI)

An enclosed rotary disc air pulser for use with a solvent extraction pulse olumn includes a housing having inlet, exhaust and pulse leg ports, a shaft mounted in the housing and adapted for axial rotation therein, first and second disc members secured to the shaft within the housing in spaced relation to each other to define a chamber therebetween, the chamber being in communication with the pulse leg port, the first disc member located adjacent the inlet port, the second disc member being located adjacent the exhaust port, each disc member having a milled out portion, the disc members positioned on the shaft so that as the shaft rotates, the milled out portions permit alternative cyclical communication between the inlet port and the chamber and the exhaust port and the chamber.

Olson, A. L. (Idaho Falls, ID); Batcheller, Tom A. (Idaho Falls, ID); Rindfleisch, J. A. (Arco, ID); Morgan, John M. (Arco, ID)

1989-01-01T23:59:59.000Z

89

Surveillance Guide - CPS 8.1 Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

HOISTING AND RIGGING HOISTING AND RIGGING 1.0 Objective The objective of this surveillance is to examine hoisting and rigging operations to ensure that safe equipment and work practices are being used. The surveillance includes verification that hoisting and rigging work is performed in accordance with DOE requirements and best practices. 2.0 References 2.1 DOE O 440.1A, Worker Protection Management For Doe Federal And Contractor Employees 2.2 DOE-RL-92-36, Hanford Site Hoisting and Rigging Manual NOTE The DOE Hoisting and Rigging Manual should be used as the primary reference for this surveillance. 1 3.0 Requirements Implemented This surveillance is conducted to implement the RL Functions, Responsibilities, and Authorities Manual (FRAM) item No. 2504. 4.0 Surveillance Activities

90

MHK Technologies/Ocean Energy Rig | Open Energy Information  

Open Energy Info (EERE)

Rig Rig < MHK Technologies Jump to: navigation, search << Return to the MHK database homepage Ocean Energy Rig.jpg Technology Profile Primary Organization Free Flow 69 Technology Resource Click here Current Technology Type Click here Axial Flow Turbine Technology Readiness Level Click here TRL 4 Proof of Concept Technology Description The Ocean Energy Rig is a hybrid concept harnessing tidal stream with increased velocity from venturi system wave and wind power The rig also uses solar panels to power computers and warning lights Other unique features include a water ballasting system with automatic self levelling and wave ramps to maximize FreeFlow 69 s new wave power device It is envisaged that the Ocean Energy Rig would be assembled and maintained in dry docks and would be towed out into position before being semi submerged and anchored for operation Power output of the production model would be at least 10MW

91

oil-emulsion (rotary) drilling fluid  

Science Journals Connector (OSTI)

oil-emulsion (rotary) drilling fluid, oil-emulsion fluid [Used where low fluid-loss, very thin cake, and good lubrication of the drill pipe are of primary importance, such as in directional drilling ...

2014-08-01T23:59:59.000Z

92

oil-base(d) (rotary) drilling fluid  

Science Journals Connector (OSTI)

oil-base(d) (rotary) drilling fluid, oil-base(d) fluid [Used primarily for drilling-in or recomputing wells in formations subject ... with low formation pressures. See remark under “drilling fluid”] ...

2014-08-01T23:59:59.000Z

93

Natural Gas Discovery and Development Impacts on Rio Vista and Its Community  

E-Print Network (OSTI)

Modern Rotary Drilling Rig………………………………………………………………………………….Equipment Used on Modern Rotary Drilling Rig 142 Figure A2.Used on Modern Rotary Drilling Rig Source: California

Gbedema, Tometi Koku

2006-01-01T23:59:59.000Z

94

C:\Documents and Settings\jhr\My Documents\C_drive\RIGS\users 2013\rigs_usersApril2013.vp  

Gasoline and Diesel Fuel Update (EIA)

23 23 Reserves Information Gathering System (RIGS) User's Guide Version 2013 For Report Year 2012 Energy Information Administration U.S. Department of Energy April 2013 Form EIA-23 Reserves Information Gathering System (RIGS) User's Guide April 2013 EIA-23 Reserves Information Gathering System (RIGS) User's Guide Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Hardware / Software Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Installing the RIGS Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installation Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Using the EIA-23 Reserves Information Gathering System (RIGS) System . . . . . . . . . . . . . . . . . 4 Initial Data Import from Last Year's RIGS Submission File. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 The RIGS Main Menu Screen.

95

Development of a portable grain mass flow sensor test rig  

Science Journals Connector (OSTI)

A portable grain mass flow sensor test rig was built to measure the accuracy of a mass flow sensor with dual use in the field as well as in the lab. Concurrently, a synchronization method was developed that employs GPS timing data to synchronize the ... Keywords: Mass flow sensor, Test rig, Yield monitor accuracy, Yield monitor error

M. Loghavi; R. Ehsani; R. Reeder

2008-05-01T23:59:59.000Z

96

HURRICANE PREDICTION, OIL RIGS, AND INSURANCE: KATRINA, RITA, AND BEYOND  

E-Print Network (OSTI)

on meteorological and oceanographic design specifications for offshore structures such as oil rigs. Dr. Forristall spent over 30 years as an offshore research engineer and advisor for Shell Oil, both nationallyHURRICANE PREDICTION, OIL RIGS, AND INSURANCE: KATRINA, RITA, AND BEYOND LUNCHEON BRIEFING

97

CRAD, Hoisting & Rigging Assessment Plan | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Hoisting & Rigging Assessment Plan Hoisting & Rigging Assessment Plan CRAD, Hoisting & Rigging Assessment Plan Performance Objective: To determine that hoisting and rigging operations are conducted according to "industry best standards" for increasing equipment reliability while assuring worker safety, and to verify issues being addressed in BN Hoisting assessment. Criteria: Lifts are identified and categorized appropriately for scheduled maintenance. DOE-STD-1090-2001 An integrated process ensures safety issues are identified and controls established. DOE-STD-1090-2001 Personnel operating and maintaining the hoisting equipment are trained; they understand their roles and responsibilities. DOE-STD-1090-2001 Maintenance conducts safety inspections of hoisting and rigging equipment on a scheduled basis, certifying that safe operations are in

98

Advanced Hot Section Materials and Coatings Test Rig  

SciTech Connect

Phase I of the Hyperbaric Advanced Hot Section Materials & Coating Test Rig Program has been successfully completed. Florida Turbine Technologies has designed and planned the implementation of a laboratory rig capable of simulating the hot gas path conditions of coal gas fired industrial gas turbine engines. Potential uses of this rig include investigations into environmental attack of turbine materials and coatings exposed to syngas, erosion, and thermal-mechanical fatigue. The principle activities during Phase 1 of this project included providing several conceptual designs for the test section, evaluating various syngas-fueled rig combustor concepts, comparing the various test section concepts and then selecting a configuration for detail design. Conceptual definition and requirements of auxiliary systems and facilities were also prepared. Implementation planning also progressed, with schedules prepared and future project milestones defined. The results of these tasks continue to show rig feasibility, both technically and economically.

Dan Davis

2006-09-30T23:59:59.000Z

99

Rotary-linear axes for high speed machining  

E-Print Network (OSTI)

This thesis presents the design, analysis, fabrication, and control of a rotary-linear axis; this axis is a key subsystem for high speed, 5-axis machine tools intended for fabricating centimeter-scale parts. The rotary-linear ...

Liebman, Michael Kevin, 1974-

2001-01-01T23:59:59.000Z

100

Hoisting & Rigging ISMS Assessment Form  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Objective: Assess the institutional and department/division hoisting and Objective: Assess the institutional and department/division hoisting and rigging (including forklift, overhead cranes small hoists, and mobile cranes) requirements, policies, procedures, and work practices for both professional and incidental activities. Review the roles and responsibilities of line managers, support personnel and workers who are involved in these activities as well as the adequacy of compliance with institutional and/or Department/Division qualifications, training requirements, and inspection requirements. Assess the laboratory's process for understanding the causes and development of effective corrective actions for incidents/accidents. Review the roles and responsibilities of line managers, support personnel and workers who are involved in the

Note: This page contains sample records for the topic "indicators rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Hoisting & Rigging ISMS Assessment Form  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Objective: Assess the institutional and department/division hoisting and Objective: Assess the institutional and department/division hoisting and rigging (including forklift, overhead cranes small hoists, and mobile cranes) requirements, policies, procedures, and work practices for both professional and incidental activities. Review the roles and responsibilities of line managers, support personnel and workers who are involved in these activities as well as the adequacy of compliance with institutional and/or Department/Division qualifications, training requirements, and inspection requirements. Assess the laboratory's process for understanding the causes and development of effective corrective actions for incidents/accidents. Review the roles and responsibilities of line managers, support personnel and workers who are involved in the

102

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5 5 HOSTILE ENVIRONMENTS 5-i Chapter 5 Hostile Environments This chapter describes provisions for hoisting and rigging operations in hostile work environments. 5.1 GENERAL ................................................................................................................................5-1 5.2 HOSTILE ENVIRONMENT PLAN ......................................................................................5-2 5.2.1 Marking and Posting ....................................................................................................5-2 5.2.2 Inspection and Testing .................................................................................................5-2 EXHIBIT I Hostile Environment Plan ............................................................................................5-3

103

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

11-i Chapter 11 11-i Chapter 11 Wire Rope and Slings CHAPTER 11 WIRE ROPE AND SLINGS This chapter provides requirements for the fabrication and use of wire rope and slings used in hoisting and rigging. 11.1 GENERAL ...............................................................................................................................11-1 11.2 WIRE ROPE ............................................................................................................................11-4 11.2.1 Wire-Rope Lays.........................................................................................................11-4 11.2.2 Wire-Rope Cores .......................................................................................................11-4 11.2.3 Wire Rope for General Purposes

104

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5 5 HOSTILE ENVIRONMENTS 5-i Chapter 5 Hostile Environments This chapter describes provisions for hoisting and rigging operations in hostile work environments. 5.1 GENERAL................................................................................................................................5-1 5.2 HOSTILE ENVIRONMENT PLAN ......................................................................................5-2 5.2.1 Marking and Posting ....................................................................................................5-2 5.2.2 Inspection and Testing .................................................................................................5-2 EXHIBIT I Hostile Environment Plan ............................................................................................5-3

105

Rotary Shaft Power Extraction From a Free-Piston Engine  

Energy.gov (U.S. Department of Energy (DOE))

A mechanical rectifier using modern high-performance mechanical diodes can improve direct rotary shaft power output.

106

EIA-23L Reserves Information Gathering System (RIGS)  

Gasoline and Diesel Fuel Update (EIA)

EIA-23L Reserves Information Gathering System (RIGS) EIA-23L Reserves Information Gathering System (RIGS) Released: April 16, 2013 Background The Form EIA-23L, "Annual Survey of Domestic Oil and Gas Reserves, " is used to collect data on reserves of crude oil, natural gas, and natural gas liquids. These data are used to develop national and regional estimates of proved reserves of domestic crude oil, natural gas, and natural gas liquids, and to facilitate national energy policy decisions. Reporting on the Form EIA-23L is mandatory. Reserves Information Gathering System The Form EIA-23L Reserves Information Gathering System (RIGS), provides respondents with an efficient and effective means for filing the form using a personal computer (PC). Hardware / Software Requirements The minimum hardware requirements needed to install and use RIGS are:

107

Hoisting & Rigging Assessment Form | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Hoisting & Rigging Assessment Form Hoisting & Rigging Assessment Form Hoisting & Rigging Assessment Form Assess the institutional and department/division hoisting and rigging (including forklift, overhead cranes small hoists, and mobile cranes) requirements, policies, procedures, and work practices for both professional and incidental activities. Review the roles and responsibilities of line managers, support personnel and workers who are involved in these activities as well as the adequacy of compliance with institutional and/or Department/Division qualifications, training requirements, and inspection requirements. Assess the laboratory's process for understanding the causes and development of effective corrective actions for incidents/accidents. Review the roles and responsibilities of line managers, support personnel and workers who are

108

HOISTING & RIGGING Assessment Plan--NNSA/Nevada Site Office Facility...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

on a scheduled basis, certifying that safe operations are in compliance with good conduct of operations. DOE-STD-1090-2001 HoistingRiggingPlan.doc More Documents &...

109

Odessa fabricator builds rig specifically for geothermal drilling...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

in the nation's oil and gas fields. Now the Odessa-based company is branching out into alternative energy. The company recently delivered its first Thermal Single rig, a...

110

Basic Rigging Workbook Training and Qualifications Program Office  

E-Print Network (OSTI)

. This instructor handbook incorporates the Subject Area's requirements, as well as information from the Department of Energy's (DOE's) Hoisting and Rigging Manual and ANSI B30.9. Definitions Asymmetrical load. An object

Ohta, Shigemi

111

DEVELOPMENT OF A ROTARY MICROFILTER FOR RADIOACTIVE WASTE APPLICATIONS  

SciTech Connect

The processing rate of Savannah River Site (SRS) high-level waste decontamination processes are limited by the flow rate of the solid-liquid separation. The baseline process, using a 0.1 micron cross-flow filter, produces {approx}0.02 gpm/sq. ft. of filtrate under expected operating conditions. Savannah River National Laboratory (SRNL) demonstrated significantly higher filter flux for actual waste samples using a small-scale rotary filter. With funding from the U. S. Department of Energy Office of Cleanup Technology, SRNL personnel are evaluating and developing the rotary microfilter for radioactive service at SRS. The authors improved the design for the disks and filter unit to make them suitable for high-level radioactive service. They procured two units using the new design, tested them with simulated SRS wastes, and evaluated the operation of the units. Work to date provides the following conclusions and program status: (1) The authors modified the design of the filter disks to remove epoxy and Ryton{reg_sign}. The new design includes welding both stainless steel and ceramic coated stainless steel filter media to a stainless steel support plate. The welded disks were tested in the full-scale unit. They showed good reliability and met filtrate quality requirements. (2) The authors modified the design of the unit, making installation and removal easier. The new design uses a modular, one-piece filter stack that is removed simply by disassembly of a flange on the upper (inlet) side of the filter housing. All seals and rotary unions are contained within the removable stack. (3) While it is extremely difficult to predict the life of the seal, the vendor representative indicates a minimum of one year in present service conditions is reasonable. Changing the seal face material from silicon-carbide to a graphite-impregnated silicon-carbide is expected to double the life of the seal. Replacement of the current seal with an air seal could increase the lifetime to 5 years and is undergoing testing in the current work. (4) The bottom bushing showed wear due to a misalignment during the manufacture of the filter tank. Replacing the graphite bushing with a more wear resistant material such as a carbide material will increase the lifetime of the bushing. This replacement requires a more wear resistant part or coating to prevent excessive wear of the shaft. The authors are currently conducting testing with the more wear resistant bushing. (5) The project team plans to use the rotary microfilter as a filter in advance of an ion exchange process under development for potential deployment in SRS waste tank risers.

Poirier, M; David Herman, D; Samuel Fink, S

2008-02-25T23:59:59.000Z

112

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

APPENDIX A PROCUREMENT GUIDELINES A-1 Appendix A Procurement Guidelines This appendix provides reference guidance in preparing purchase requisitions for hoisting and rigging materials and equipment. Nationally recognized standards and specifications are referenced for listed items. However, caution should be used prior to procurement of special items in order to verify appropriate specification or standard reference and requirements. Some specific requirements listed in this appendix are more restrictive than consensus standard requirements, but are recommended to ensure materials of adequate quality and workmanship are provided. Quality receipt inspections should be provided for all received materials in order to verify compliance of all

113

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

APPENDIX A APPENDIX A PROCUREMENT GUIDELINES A-i Appendix A Procurement Guidelines This appendix provides reference guidance in preparing purchase requisitions for hoisting and rigging materials and equipment. Nationally recognized standards and specifications are referenced for listed items. However, caution should be used prior to procurement of special items in order to verify appropriate specification or standard reference and requirements. Some specific requirements listed in this appendix are more restrictive than consensus standard requirements, but are recommended to ensure materials of adequate quality and workmanship are provided. Quality receipt inspections should be provided for all received materials in order to verify compliance of all

114

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

TERMINOLOGY AND DEFINITIONS 1-1 Chapter 1 Terminology and Definitions The following are specialized terms commonly used when discussing hoisting and rigging operations. Many may not be used in this standard, but are included for general information. The terms are arranged in alphabetical order. Illustrations are included for clarity. ABRASION: Surface wear. ACCELERATION STRESS: Additional stress imposed due to increasing load velocity. ALTERNATE LAY: Lay of wire rope in which the strands are alternately regular and lang lay. ANSI: American National Standards Institute. APPOINTED: Assigned specific responsibilities by the employer or the employer's representative. AREA, METALLIC: Sum of the cross- sectional areas of individual wires in a wire rope

115

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

TERMINOLOGY AND DEFINITIONS 1-1 Chapter 1 Terminology and Definitions The following are specialized terms commonly used when discussing hoisting and rigging operations. Many may not be used in this standard, but are included for general information. The terms are arranged in alphabetical order. Illustrations are included for clarity. ABRASION: Surface wear. ACCELERATION STRESS: Additional stress imposed due to increasing load velocity. ALTERNATE LAY: Lay of wire rope in which the strands are alternately regular and lang lay. ANSI: American National Standards Institute. APPOINTED: Assigned specific responsibilities by the employer or the employer's representative. AREA, METALLIC: Sum of the cross- sectional areas of individual wires in a wire rope

116

The Feasibility of Natural Gas as a Fuel Source for Modern Land-Based Drilling Rigs  

E-Print Network (OSTI)

rigs are still in use today, most modern drilling rigs are electrically powered. Electric drilling rig engines are coupled to electric generators, in what is called a generator set, or genset, which creates electricity that powers electric motors... drilling rigs can be categorized into either direct current (DC) or alternating current (AC), depending on the type of electricity the rig generators produce. Electric motors power the draw-works, top drive, mud pumps, and other systems with electricity...

Nunn, Andrew Howard

2012-02-14T23:59:59.000Z

117

Rotary Mode Core Sample System availability improvement  

SciTech Connect

The Rotary Mode Core Sample System (RMCSS) is used to obtain stratified samples of the waste deposits in single-shell and double-shell waste tanks at the Hanford Site. The samples are used to characterize the waste in support of ongoing and future waste remediation efforts. Four sampling trucks have been developed to obtain these samples. Truck I was the first in operation and is currently being used to obtain samples where the push mode is appropriate (i.e., no rotation of drill). Truck 2 is similar to truck 1, except for added safety features, and is in operation to obtain samples using either a push mode or rotary drill mode. Trucks 3 and 4 are now being fabricated to be essentially identical to truck 2.

Jenkins, W.W.; Bennett, K.L.; Potter, J.D. [Westinghouse Hanford Co., Richland, WA (United States); Cross, B.T.; Burkes, J.M.; Rogers, A.C. [Southwest Research Institute (United States)

1995-02-28T23:59:59.000Z

118

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 4 BELOW-THE-HOOK LIFTING DEVICES 14-i Chapter 14 Below-the-Hook Lifting Devices This chapter provides the requirements for below-the-hook lifting devices used in hoisting and rigging, such as spreader bars, lifting yokes, and lift fixtures. This section implements the requirements of ASME B30.20, "Below-the-Hook Lifting Devices." NOTE: Special lifting devices for shipping containers weighing 10,000 lb or more that are used for radioactive materials may be governed by ANSI N14.6 ["Standard for Special Lifting Devices for Shipping Containers Weighing 10,000 Pounds (4,500 kg) or More for Nuclear Materials."] 14.1 GENERAL ...............................................................................................................................14-1

119

Rollover analysis of rotary mode core sampler truck No. 2  

SciTech Connect

This document provides estimate of limiting speed and rollover analysis of rotary mode core sampler truck No. 2 (RMCST No. 2).

Ziada, H.H.

1994-11-08T23:59:59.000Z

120

Professional development of new rig supervisors a must  

SciTech Connect

This paper reports that because the number of drilling personnel has dropped dramatically over the last decade, many operators now face a shortage of competent rig supervisors. To be effective, the rig supervisor must develop a knowledge of drilling operations, apply optimization techniques to improve drilling performance, demand safe work practices, and protect the environment. Petroleum engineering degree programs and industry training programs can teach the rig supervisor specific technical and management skills; however, traditionally, the supervisor trainee shadows an experienced company man to learn how to direct a drilling operation. The success of this method depends not only on the skills and learning capabilities of the trainee but also on the trainer's time, motivation, knowledge, and ability to teach the skills necessary to direct drilling activities.

Nordt, D.P. (Marathon Oil Co., Houston, TX (United States)); Stone, M.S. (Marathon Oil Co., Bridgeport, IL (United States))

1992-10-26T23:59:59.000Z

Note: This page contains sample records for the topic "indicators rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Natural Gas for the Long Haul (Big Rigs Go Green)  

NLE Websites -- All DOE Office Websites (Extended Search)

the Long Haul (Big Rigs Go Green) the Long Haul (Big Rigs Go Green) JOHN DAVIS: No one has been hit harder by rising fuel prices than America's long-haul commercial truckers. A big rig can easily burn 20,000 gallons of fuel a year, and with diesel prices projected to keep rising, this not only pinches the trucker's bottom line, but that extra cost is passed on to American consumers. Meanwhile, natural gas prices have remained stable and are forecast to stay that way for years to come. Up to now, demand for natural gas as a transportation fuel has been mostly for compressed natural gas used by light and medium-duty vehicles. City buses, refuse haulers, utilities, and

122

Inventory management of steel plates at an oil rig construction company .  

E-Print Network (OSTI)

??Keppel Fels produces make-to-order oil exploration rigs for the global market. Each rig requires close to 6000 metric tons of steel in the course of… (more)

Tan, Chien Yung

2006-01-01T23:59:59.000Z

123

Inventory management of steel plates at an oil rig construction company  

E-Print Network (OSTI)

Keppel Fels produces make-to-order oil exploration rigs for the global market. Each rig requires close to 6000 metric tons of steel in the course of its production. Optimal management of this steel is very critical in this ...

Tan, Chien Yung

2006-01-01T23:59:59.000Z

124

Rotary Pipeline Processors Simon Moore, Peter Robinson, Steve Wilcox  

E-Print Network (OSTI)

DRAFT Rotary Pipeline Processors Simon Moore, Peter Robinson, Steve Wilcox Computer Laboratory, University of Cambridge Submitted: 15th December, 1995 Revised: 30th May, 1996 Abstract The rotary pipeline processor is a new architecture for su- perscalar computing. It is based on a simple and regular pipeline

Robinson, Peter

125

Doubts swirl around plan to use rigs as reefs  

Science Journals Connector (OSTI)

... Offshore oil platforms could be allowed to remain in place as artificial habitats for marine life ... oil stops flowing, and to leave the sites as they found them. But the Rigs to Reefs Act of 2003, which is sponsored by Representative David Vitter (Republican, ...

Betsy Mason

2003-10-30T23:59:59.000Z

126

Ministers block disposal of oil rigs at sea  

Science Journals Connector (OSTI)

... ministers last week ended three years of public controversy about the fate of disused oil rigs in the northeast Atlantic ocean. They decided that most will have to be dismantled ... all environmentalist groups. Oil companies, on the other hand, were disappointed. The UK Offshore Operators Association said the decision to outlaw deep-sea disposal of oil and gas ...

Ehsan Masood

1998-07-30T23:59:59.000Z

127

Hoisting and Rigging: Lift Planning and Control for Ordinary Lifts  

E-Print Network (OSTI)

operator Follow specific instructions/procedures for attachment of the rigging gear to the load. Use. Repeat as necessary until the load is evenly balanced. Follow "Conduct of Operator" requirements2 Stop at the work site and follow the plan Assign a designated leader Ensure all personnel involved in the lift

Wechsler, Risa H.

128

Mixed Stream Test Rig Winter FY-2011 Report  

SciTech Connect

This report describes the data and analysis of the initial testing campaign of the Mixed Stream Test Rig (MISTER) at Idaho National Laboratory (INL). It describes the test specimen selection, physical configuration of the test equipment, operations methodology, and data and analysis of specimens exposed in two environments designed to represent those expected for high temperature steam electrolysis (HTSE).

Chalres Park; Tedd Lister; Kevin DeWall

2011-04-01T23:59:59.000Z

129

Planning and scheduling a fleet of rigs using simulation-optimization  

Science Journals Connector (OSTI)

Some of the most important and expensive activities in the oil field development and production phases relate to using rigs. These can be used for drilling wells, or for maintenance activities. As rigs are usually scarce compared to the number of wells ... Keywords: Planning, Rigs, Scheduling, Simulation-optimization

Hugo ViníCius Bassi; VirgíLio Jose Martins Ferreira Filho; Laura Bahiense

2012-12-01T23:59:59.000Z

130

Rotary seal with improved film distribution  

DOE Patents (OSTI)

The present invention is a generally circular rotary seal that establishes sealing between relatively rotatable machine components for lubricant retention and environmental exclusion, and incorporates seal geometry that interacts with the lubricant during relative rotation to distribute a lubricant film within the dynamic sealing interface. The features of a variable inlet size, a variable dynamic lip flank slope, and a reduction in the magnitude and circumferentially oriented portion of the lubricant side interfacial contact pressure zone at the narrowest part of the lip, individually or in combination thereof, serve to maximize interfacial lubrication in severe operating conditions, and also serve to minimize lubricant shear area, seal torque, seal volume, and wear, while ensuring retrofitability into the seal grooves of existing equipment.

Dietle, Lannie Laroy; Schroeder, John Erick

2013-10-08T23:59:59.000Z

131

Department of Energy Supercomputer Helps Design More Efficient Big Rigs |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Department of Energy Supercomputer Helps Design More Efficient Big Department of Energy Supercomputer Helps Design More Efficient Big Rigs Department of Energy Supercomputer Helps Design More Efficient Big Rigs February 8, 2011 - 12:00am Addthis Washington, DC - BMI Corporation, a company in South Carolina, in partnership with the Department of Energy's Oak Ridge National Laboratory (ORNL) has successfully developed a technology that will make semi trucks more fuel efficient with the potential to save millions of gallons of fuel. Utilizing the nation's most powerful computer, BMI Corp designed a SmartTruck UnderTray System, a set of integrated aerodynamic fairings that improve the aerodynamics of 18-wheeler (Class 8) long-haul trucks. If all 1.3 million Class 8 trucks in the U.S. were configured with these components, companies could achieve annual savings of 1.5 billion gallons

132

Computational Modeling of Relevant Automotive Rotary Spray Painting Process  

Science Journals Connector (OSTI)

During the automotive spray painting process, metallic car shells are conveyed at ... specified constant rectilinear speed through the booth. Robot-assisted rotary atomizers spray the car shell ... path particula...

Abraham J. Salazar

2013-01-01T23:59:59.000Z

133

Evaluation of Alternative Filter Media for the Rotary Microfilter  

SciTech Connect

M. R. Poirier , D. T. Herman & R. Bhave (2012) Evaluation of Alternative Filter Media for the Rotary Microfilter, Separation Science and Technology, 47:14-15, 2108-2114

Poirier, M. [Savannah River National Laboratory, Environmental and Chemical Process Technology; Herman, [Savannah River National Laboratory, Environmental and Chemical Process Technology; Bhave, Ramesh R [ORNL

2012-01-01T23:59:59.000Z

134

Purifying rotary kiln waste gases in chamotte burning  

Science Journals Connector (OSTI)

A study of the operation of electric filters connected to rotary kilns for burning clay into chamotte showed that to increase the dust extraction efficiency it is necessary: with dust concentrations in the gas...

Yu. I. Chander; S. Z. Belinskii; L. G. Borisovskii

135

Novel design of a rotary valve using axiomatic design  

E-Print Network (OSTI)

Rotary valves have existed for millennia; and while they have developed tremendously since the first Roman valves, many of the same problems have persisted. The basic problems are caused by the coupling of functional ...

Peliks, Robert Bilgor

2005-01-01T23:59:59.000Z

136

Surf zone monitoring using rotary wing Unmanned Aerial Vehicles  

Science Journals Connector (OSTI)

We investigate the potential of rotary wing Unmanned Aerial Vehicles (UAVs) to monitor the surf zone. We show that these UAVs are extremely flexible surveying platforms that can gather near-continuous, moderate spatial and high temporal resolution ...

Ronald L. Brouwer; Matthieu A. de Schipper; Patrick F. Rynne; Fiona J. Graham; Ad J.H.M. Reniers; Jamie H. MacMahan

137

An energy-saving oil drilling rig for recovering potential energy and decreasing motor power  

Science Journals Connector (OSTI)

An energy-saving oil drilling rig is researched. A large accumulator is adopted in this rig to store the energy of the motor during the auxiliary time of lifting the drill stem and the potential energy of the drill stem when lowered. The equipped power of this rig decreases remarkably compared with the conventional drilling rig, and this rig can also recover and reuse the potential energy of the drill stem. Therefore, this rig owns remarkable energy-saving effect compared with the conventional drilling rig, and the energy-saving effect of the energy-saving oil drilling rig is also verified by the field tests. The mathematical model of the energy-saving oil drilling rig lowering the drill stem was derived and simulation analysis was conducted. Through simulation the curves of the drill stem lowering velocity and lowering displacement with time were obtained, and some conclusions were reached: (1) the heavier the drill stem lowered, the higher the lowering velocity is, and the shorter the lowering time is; (2) the smaller the displacement of the variable pump-motor, the higher the lowering velocity is, and the shorter the lowering time is.

Lujun Zhang

2011-01-01T23:59:59.000Z

138

CPS 8.1 Hoisting and Rigging, 2/25/2000  

Energy.gov (U.S. Department of Energy (DOE))

The objective of this surveillance is to examine hoisting and rigging operations to ensure that safe equipment and work practices are being used.  The surveillance includes verification that...

139

HOISTING & RIGGING Assessment Plan--NNSA/Nevada Site Office Facility Representative Division  

Energy.gov (U.S. Department of Energy (DOE))

:  To determine that hoisting and rigging operations areconducted according to “industry best standards” for increasing equipment reliabilitywhile assuring worker safety, and to verify issues being...

140

,,,,,"Rig: TOI Discoverer Enterprise"  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Well: OCS-G 32306 002 ST00BP00",,,,"Flow Data" Well: OCS-G 32306 002 ST00BP00",,,,"Flow Data" ,,,,,"Field: Mississippi Canyon 252" ,,,,,"Rig: TOI Discoverer Enterprise" ,,,,,"Choke Manifold",,,,"Rates",,,,,,,,,"Ratio" "Date","Time","Choke A","Choke B","BSW","WHPres","WHTemp","WHDCP","WHDCTemp","Gas Rate","Gas Cum","Uncorrected ","Uncorrected ","Water Rate","Water Cum","Uncorrected ","Uncorrected ","Cumulative Oil ","GOR1","Comments" ,,,,,,,,,,,"Oil Rate","Oil Cum ",,,"Liquid Rate","Liquid Cum","from Cargo "

Note: This page contains sample records for the topic "indicators rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Technical and economic evaluation of selected compact drill rigs for drilling 10,000 foot geothermal production wells  

SciTech Connect

This report summarizes the investigation and evaluation of several {open_quotes}compact{close_quotes} drill rigs which could be used for drilling geothermal production wells. Use of these smaller rigs would save money by reducing mobilization costs, fuel consumption, crew sizes, and environmental impact. Advantages and disadvantages of currently-manufactured rigs are identified, and desirable characteristics for the {open_quotes}ideal{close_quotes} compact rig are defined. The report includes a detailed cost estimate of a specific rig, and an evaluation of the cost/benefit ratio of using this rig. Industry contacts for further information are given.

Huttrer, G.W. [Geothermal Management Company, Inc., Frisco, CO (United States)

1997-11-01T23:59:59.000Z

142

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

NLE Websites -- All DOE Office Websites (Extended Search)

Rotary Firing in Ring-Shaped Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Wednesday, 28 April 2010 00:00 Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

143

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

NLE Websites -- All DOE Office Websites (Extended Search)

Rotary Firing in Ring-Shaped Protein Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Wednesday, 28 April 2010 00:00 Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

144

Pick sequencing optimization problem in the rotary rack S/R system  

Science Journals Connector (OSTI)

The problem of pick sequencing in the rotary rack S/R system (PPS-RRS) is ... of minimizing the execution time. The rotary rack S/R system consists of one S/...

Pan Zhang; Lei Jia; Guohui Tian

2004-08-01T23:59:59.000Z

145

Development of multiscale models for the performance of the gas and oil seals in rotary engines  

E-Print Network (OSTI)

Rotary engines offer higher power density, fewer parts and lower vibrations than conventional reciprocating piston engines. However, rotary engines are more difficult to seal because of the rotor shape which leads to higher ...

Picard, Mathieu

2014-01-01T23:59:59.000Z

146

Planning and scheduling a fleet of rigs using simulation–optimization  

Science Journals Connector (OSTI)

Some of the most important and expensive activities in the oil field development and production phases relate to using rigs. These can be used for drilling wells, or for maintenance activities. As rigs are usually scarce compared to the number of wells requiring service, a schedule of wells to be drilled or repaired must be devised. The objective is to minimize opportunity costs within certain operating constraints. This paper present the first stochastic approach to deals with the problem of planning and scheduling a fleet of offshore oil rigs, where the service time is assumed being uncertain. A simulation–optimization method is used to generate “expected solutions” and performance measures for rigs, as well as statistics about well allocation to rigs. The methodology can be used in two different ways – to schedule an existing fleet of rigs or to scale the size of the fleet – both contemplating the uncertain nature of the problem. The method’s expected results include performance measures for each rig, expected delay for a well to be served, the expected schedule of rigs, and a distribution of the well servicing order. The experiments based on real situations demonstrate the effectiveness of the simulation–optimization approach.

Hugo Vinícius Bassi; Virgílio Jose Martins Ferreira Filho; Laura Bahiense

2012-01-01T23:59:59.000Z

147

Structural Basis of Viral RNA Recognition by RIG-I-Like Receptors  

E-Print Network (OSTI)

binding surface also abolished RIG-I signaling in cells. In order to compare the RIG-I/RNA interactions with other RLRs, we also determined the dsRNA binding surface of MDA5 CTD by NMR titration studies. MDA5 CTD has a similar binding surface...

Lu, Cheng

2012-10-19T23:59:59.000Z

148

Numerical and experimental determination of neutron characteristics in irradiation rigs operated in LVR-15 research reactor  

Science Journals Connector (OSTI)

......standard single-cell CHOUCA rigs or...dedicated multi-cell rigs. The temperature...reflector and in fuel will be provided...dedicated to material degradation evaluation. IRRADIATION...evaluation of material degradation induced by radiation...averaged over cell) has to be modified...reflects actual fuel burnup distribution......

Michal Koleska; Ladislav Viererbl; Zdena Lahodova; Jaroslav Ernest; Jelena Zmitkova; Milan Marek

2014-10-01T23:59:59.000Z

149

Safety First Safety Last Safety Always Inspect rigging equipment for material handling before use  

E-Print Network (OSTI)

Safety First Safety Last Safety Always Inspect rigging equipment for material handling before use. Rigging Equipment for Material Handling Safety Tip #19 At your job or at the plate, you can't get home on the reverse side of this safety tip sheet. Please refrain from reading the information verbatim

Minnesota, University of

150

Results of no-flow rotary drill bit comparison testing  

SciTech Connect

This document describes the results of testing of a newer rotary sampling bit and sampler insert called the No-Flow System. This No-Flow System was tested side by side against the currently used rotary bit and sampler insert, called the Standard System. The two systems were tested using several ''hard to sample'' granular non-hazardous simulants to determine which could provide greater sample recovery. The No-Flow System measurably outperformed the Standard System in each of the tested simulants.

WITWER, K.S.

1998-11-30T23:59:59.000Z

151

The design of a test rig for the identification of dynamic coefficients of a high temperature magnetic bearing  

E-Print Network (OSTI)

This thesis is a report on the research and Micrographics. development to design a test rig for the identification of the dynamic coefficients of a radial magnetic bearing. The test rig development is intended for dynamic coefficient observation...

Rahtika, I Putu Gede Sopan

1998-01-01T23:59:59.000Z

152

Selectively fired, tubing-conveyed perforating guns save rig time  

SciTech Connect

Selective firing of tubing-conveyed perforating (TCP) guns during drill stem tests (DSTs) added flexibility and saved costs for Marathon Oil Co. As an example, in the Garland field in Wyoming, the guns allowed perforating multiple zones in one trip. This saved 1 1/2--2 days/well in rig time and $25,000--30,000/well in electric wire line and DST tool charges. For international offshore operations, savings of $200,000/well appear possible. Savings result not only from perforating multiple zones, but also from arbitrarily setting firing patterns with or without zone isolation. The paper describes the testing of equipment, the design of the guns, firing heads, crossover assembly, pressure isolation sub, control line, and select-fire sub, and applications for the guns.

Snider, P.M. (Marathon Oil Co., Houston, TX (United States)); Bond, P.L. (Halliburton Energy Services, Dallas, TX (United States))

1993-07-19T23:59:59.000Z

153

Stratigraphy of the PB-1 well, Nopal I uranium deposit, Sierra Pena Blanca, Chihuahua, Mexico  

E-Print Network (OSTI)

was stuck. A portable rotary rig (Prospector model TKT-1000)out of the hole, the rotary rig was again moved to thethen reamed out using the rotary rig with an 8 ½" diameter

Dobson, P.

2009-01-01T23:59:59.000Z

154

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

NLE Websites -- All DOE Office Websites (Extended Search)

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

155

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

NLE Websites -- All DOE Office Websites (Extended Search)

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

156

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

NLE Websites -- All DOE Office Websites (Extended Search)

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

157

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

NLE Websites -- All DOE Office Websites (Extended Search)

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

158

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

NLE Websites -- All DOE Office Websites (Extended Search)

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

159

ATP Synthase: Two rotary molecular motors working together  

E-Print Network (OSTI)

1 ATP Synthase: Two rotary molecular motors working together George Oster Hongyun Wang University of California, Berkeley Introduction ATP synthaseÃ?also called FoF1 ATPase, or simply F-ATPaseÃ?is the universal protein that terminates oxidative phosphorylation by synthesizing ATP from ADP and phosphate. Nearly

Wang, Hongyun

160

Micro rotary machine and methods for using same  

DOE Patents (OSTI)

A micro rotary machine may include a micro actuator and a micro shaft coupled to the micro actuator. The micro shaft comprises a horizontal shaft and is operable to be rotated by the micro actuator. A micro tool is coupled to the micro shaft and is operable to perform work in response to motion of the micro shaft.

Stalford, Harold L. (Norman, OK)

2012-04-17T23:59:59.000Z

Note: This page contains sample records for the topic "indicators rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Rotary Pipeline Processors Simon Moore, Peter Robinson, Steve Wilcox  

E-Print Network (OSTI)

DRAFT Rotary Pipeline Processors Simon Moore, Peter Robinson, Steve Wilcox Computer Laboratory pipeline processor is a new architecture for su- perscalar computing. It is based on a simple and regular pipeline structure which can support several ALUs for effi- cient dispatching of multiple instructions

Moore, Simon

162

Calculator program optimizes bit weight, rotary speed, reducing drilling cost  

SciTech Connect

Bit selection, bit weight, and rotary speed have repeatedly proven to be the most important and commonly overlooked alterable factors which control penetration rate, footage, and overall drilling cost. This is particularly true in offshore operations where drilling costs are highest and the greatest cost savings stand to be achieved through implementation of proven optimization techniques. The myth that bit weights and rotary speeds cannot be optimized in directional holes has hindered the industry from using this virtually cost-free method for reducing drilling cost. The use of optimized bit weights and rotary speeds in conjunction with minimum cost bit programs based on cost per foot analysis of previous bit runs in the area was implemented on a five-well platform in the Grand Isle Block 20 field, offshore Louisiana. Each of the directional wells was drilled substantially faster and cheaper than the discovery well, which was a straight hole. Average reductions in footage cost of 31.3%, based on daily operating cost of $30,000/day, and increase in average daily footage drilled of 45.2% were effected by ''collectively optimizing'' drilling performance. The ''Optimizer'' program is an HP-41CV adaptation of the Bourgoyne and Young drilling model. It was used to calculate the optimum bit weights and rotary speeds based on field drilling tests; historical bit and bearing wear data; and current operating conditions, cost, and constraints.

Simpson, M.A.

1984-04-23T23:59:59.000Z

163

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

NLE Websites -- All DOE Office Websites (Extended Search)

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

164

Development of a Rotary Micro-filter for Radioactive Waste Applications  

SciTech Connect

The processing rates of Savannah River Site (SRS) high-level waste decontamination processes are limited by the flow rate of the solid-liquid separation. The baseline process, using a 0.1 micron cross-flow filter, produces {approx}1.36 x 10{sup -5} m/s ({approx}0.02 gpm/ft{sup 2}) of filtrate under expected operating conditions. Savannah River National Laboratory (SRNL) demonstrated significantly higher filter flux for actual waste samples using a small-scale rotary filter. With funding from the U. S. Department of Energy Office of Cleanup Technology, SRNL personnel are evaluating and developing the rotary micro-filter for radioactive service at SRS. The authors improved the design for the disks and filter unit to make them suitable for high-level radioactive service. They procured two units using the new design, tested them with simulated SRS wastes, and evaluated the operation of the units. Work to date provides the following conclusions and program status. - The authors modified the design of the filter disks to remove epoxy and Ryton{sup R}. The new design includes welding both stainless steel and ceramic coated stainless steel filter media to a stainless steel support plate. The welded disks were tested in the full-scale unit. They showed good reliability and met filtrate quality requirements. - The authors modified the design of the unit, making installation and removal easier. The new design uses a modular, one-piece filter stack that is removed simply by disassembly of a flange on the upper (inlet) side of the filter housing. All seals and rotary unions are contained within the removable stack. - While it is extremely difficult to predict the life of the seal, the vendor representative indicates a minimum of one year in present service conditions is reasonable. Changing the seal face material from silicon-carbide to a graphite-impregnated silicon-carbide is expected to double the life of the seal. Replacement of the current seal with an air seal could increase the lifetime to 5 years and is undergoing testing in the current work. - The bottom bushing showed wear due to a misalignment during the manufacture of the filter tank. Replacing the graphite bushing with a more wear resistant material such as a carbide material will increase the lifetime of the bushing. This replacement requires a more wear resistant part or coating to prevent excessive wear of the shaft. The authors are currently conducting testing with the more wear resistant bushing. - The project team plans to use the rotary micro-filter as a filter in advance of an ion exchange process under development for potential deployment in SRS waste tank risers. (authors)

Poirier, M.R.; Herman, D.T.; Fink, S.D. [Savannah River National Laboratory, Aiken, SC (United States)

2008-07-01T23:59:59.000Z

165

Wide and multiple apex seals for the rotary engine: (Abbr.: Multi-Apex-Seals for the Rotary Engine)  

Science Journals Connector (OSTI)

Abstract Conventional rotary engines are based on a trochoidal-type housing bore profile and its inside envelope is the basis of the rotor profile. To seal the chambers, spring-loaded apex seals are used in place of the designed rotor apexes. The conventional design method is limited to an epitrochoidal-based housing and does not consider the apex seal profile. Previously the authors presented the complete theory and algorithm of the deviation-function (DF) method of rotary engine design based on the apex seal profile. By using the DF method, the apex seal and engine housing bore are conjugate kinematic pairs, which enable the design of a variety of apex seals that conform to the bore, including wider apex seals and multiple seals at each rotor apex. The wide apex seal design has better rotor-to-housing conformity and therefore improves sealing. The multi-apex-seal grid assembly improves sealing capability and also reduces the forces on the apex seals. The incorporation of apex seal profiles into the rotary engine design process also makes possible a larger variety of new rotary engine profiles.

Sarah Warren Rose; Daniel C.H. Yang

2014-01-01T23:59:59.000Z

166

Drill bit having a failure indicator  

SciTech Connect

A lubrication system is described to indicate a decrease in lubricant volume below a predetermined level in a rotary drill bit having a bit body adapted to receive drilling fluid at a high first pressure from a suspended drill string, and adapted to discharge the drilling fluid therefrom in a void space between the bit body and an associated well bore with the drilling fluid in the space being at a low second pressure.

Daly, J.E.; Pastusek, P.E.

1986-09-09T23:59:59.000Z

167

HOISTING & RIGGING Assessment Plan--NNSA/Nevada Site Office Facility  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

HOISTING & RIGGING Assessment Plan--NNSA/Nevada Site Office HOISTING & RIGGING Assessment Plan--NNSA/Nevada Site Office Facility Representative Division HOISTING & RIGGING Assessment Plan--NNSA/Nevada Site Office Facility Representative Division : To determine that hoisting and rigging operations are conducted according to "industry best standards" for increasing equipment reliability while assuring worker safety, and to verify issues being addressed in BN Hoisting assessment. Criteria: Lifts are identified and categorized appropriately for scheduled maintenance. DOE-STD-1090-2001 An integrated process ensures safety issues are identified and controls established. DOE-STD-1090-2001 Personnel operating and maintaining the hoisting equipment are trained; they understand their roles and responsibilities. DOE-STD-1090-2001

168

Motor Drives of Modern Drilling and Servicing Rigs for Oil and Gas Wells  

Science Journals Connector (OSTI)

This paper provides a synthetic view on the most recent achievements in the field of drilling and servicing rig drives for oil and gas wells. This field is featuring ... kilowatts and speeds of 150–250 rpm for drilling

Aurelian Iamandei; Gheorghe Miloiu

2013-01-01T23:59:59.000Z

169

E-Print Network 3.0 - advanced seal rig Sample Search Results  

NLE Websites -- All DOE Office Websites (Extended Search)

2 3 4 5 > >> Page: << < 1 2 3 4 5 > >> 41 Heat Transfer Research, 2010, Vol. 41, No. 6 Turbine Aero-Heat Transfer Studies Summary: , rotating turbine research rigs, realistic gas...

170

Analytical and experimental investigations of a labyrinth seal test rig and damper seals for turbomachinery  

E-Print Network (OSTI)

. The test rig is also used during the development of a unique damper seal device. The experimental data used to determine the direct damping coefficient of the damper seal device are presented. Results of vibration and pressure measurements that demonstrate...

Shultz, Richard Raymond

1997-01-01T23:59:59.000Z

171

Rotary union for use with ultrasonic thickness measuring probe  

DOE Patents (OSTI)

A rotary union for rotatably supporting an ultrasonic probe operable to nondestructively measure the thickness of steam generator tubes to determine the amount of corrosion experienced by the tubes includes a stationary body having a bore therethrough and an outlet drain, and a fitting rotatably mounted within the upper end of the body. The fitting has a bore aligned with the bore of the body. An electrical cable positioned within a water supply tube in an annular arrangement passes through the bore of the body and the bore of the fitting. This annular arrangement, in turn, is positioned within a connector element which extends outwardly from the fitting bore and is connected to the ultrasonic probe. An elastomeric lower bushing seals the annular arrangement to the lower end of the rotary union body and an elastomeric upper bushing seals the connector element to the fitting to permit the connector element and the ultrasonic probe connected thereto to rotate with the fitting relative to the body. The lower and upper bushings permit water to be passed through the annular arrangement and into the ultrasonic probe and thereafter discharged between the annular arrangement and the connector element to the outlet drain of the rotary union body. 5 figs.

Nachbar, H.D.

1992-09-15T23:59:59.000Z

172

Design and fabrication of a bending rotation fatigue test rig for in situ electrochemical analysis during fatigue testing of NiTi shape memory alloy wires  

Science Journals Connector (OSTI)

The current investigation proposes a novel method for simultaneous assessment of the electrochemical and structural fatigue properties of nickel-titanium shape memory alloy (NiTi SMA) wires. The design and layout of an in situ electrochemical cell in a custom-made bending rotation fatigue (BRF) test rig is presented. This newly designed test rig allows performing a wide spectrum of experiments for studying the influence of fatigue on corrosion and vice versa. This can be achieved by performing ex situ and/or in situ measurements. The versatility of the combined electrochemical/mechanical test rig is demonstrated by studying the electrochemical behavior of NiTi SMA wires in 0.9% NaCl electrolyte under load. The ex situ measurements allow addressing various issues for example the influence of pre-fatigue on the localized corrosion resistance or the influence of hydrogen on fatigue life. Ex situ experiments showed that a pre-fatigued wire is more susceptible to localized corrosion. The synergetic effect can be concluded from the polarization studies and specifically from an in situ study of the open circuit potential (OCP) transients which sensitively react to the elementary repassivation events related to the local failure of the oxide layer. It can also be used as an indicator for identifying the onset of the fatigue failure.

Jenni Kristin Zglinski; Matthias Frotscher

2013-01-01T23:59:59.000Z

173

Design and fabrication of a bending rotation fatigue test rig for in situ electrochemical analysis during fatigue testing of NiTi shape memory alloy wires  

SciTech Connect

The current investigation proposes a novel method for simultaneous assessment of the electrochemical and structural fatigue properties of nickel-titanium shape memory alloy (NiTi SMA) wires. The design and layout of an in situ electrochemical cell in a custom-made bending rotation fatigue (BRF) test rig is presented. This newly designed test rig allows performing a wide spectrum of experiments for studying the influence of fatigue on corrosion and vice versa. This can be achieved by performing ex situ and/or in situ measurements. The versatility of the combined electrochemical/mechanical test rig is demonstrated by studying the electrochemical behavior of NiTi SMA wires in 0.9% NaCl electrolyte under load. The ex situ measurements allow addressing various issues, for example, the influence of pre-fatigue on the localized corrosion resistance, or the influence of hydrogen on fatigue life. Ex situ experiments showed that a pre-fatigued wire is more susceptible to localized corrosion. The synergetic effect can be concluded from the polarization studies and specifically from an in situ study of the open circuit potential (OCP) transients, which sensitively react to the elementary repassivation events related to the local failure of the oxide layer. It can also be used as an indicator for identifying the onset of the fatigue failure.

Neelakantan, Lakshman [Ruhr-Universitaet Bochum, Institute for Materials, 44801 Bochum (Germany); Department of Metallurgical and Materials Engineering, Indian Institute of Technology Madras, 600 036 Chennai (India); Zglinski, Jenni Kristin; Eggeler, Gunther [Ruhr-Universitaet Bochum, Institute for Materials, 44801 Bochum (Germany); Frotscher, Matthias [Ruhr-Universitaet Bochum, Institute for Materials, 44801 Bochum (Germany); CORTRONIK GmbH, 18119 Rostock-Warnemuende (Germany)

2013-03-15T23:59:59.000Z

174

E-Print Network 3.0 - alpha rotary joint Sample Search Results  

NLE Websites -- All DOE Office Websites (Extended Search)

Drilling Diana LaBelle, John Bares, Illah Nourbakhsh Summary: , thrust, rotary speed and penetration rate, to train a neural network to classify rock. Section 2... applications...

175

Systems acceptance and operability testing for rotary mode core sampling in flammable gas tanks  

SciTech Connect

This document provides instructions for the system acceptance and operability testing of the rotary mode core sampling system, modified for use in flammable gas tanks.

Corbett, J.E., Westinghouse Hanford

1996-07-29T23:59:59.000Z

176

Apparatus and method for controlling the rotary airlocks in a coal processing system by reversing the motor current rotating the air lock  

DOE Patents (OSTI)

An improvement to a coal processing system where hard materials found in the coal may cause jamming of either inflow or outflow rotary airlocks, each driven by a reversible motor. The instantaneous current used by the motor is continually monitored and compared to a predetermined value. If an overcurrent condition occurs, indicating a jamming of the airlock, a controller means starts a "soft" reverse rotation of the motor thereby clearing the jamming. Three patterns of the motor reversal are provided.

Groombridge, Clifton E. (Hardin, MT)

1996-01-01T23:59:59.000Z

177

Accepted Manuscript A wall heat transfer correlation for the baffled-rotary kilns with secondary air  

E-Print Network (OSTI)

Accepted Manuscript A wall heat transfer correlation for the baffled-rotary kilns with secondary;1 A wall heat transfer correlation for the baffled- rotary kilns with secondary air flow and recycled industrial applications suggests examining the heat transfer phenomena in order to improve the multi

Boyer, Edmond

178

Rotary Wing UAV Position Control using Backstepping Bilal Ahmed, Hemanshu R. Pota and Matt Garratt  

E-Print Network (OSTI)

Rotary Wing UAV Position Control using Backstepping Bilal Ahmed, Hemanshu R. Pota and Matt Garratt Abstract-- This paper presents a novel position control method for rotary wing UAVs using the backstepping for underactuated UAV including the flybar and flapping dynamics when stability derivatives are not available

Pota, Himanshu Roy

179

Structural model of F1–ATPase and the implications for rotary catalysis  

Science Journals Connector (OSTI)

...and R. M. Simmons Structural model of F1-ATPase and the implications for rotary...crystal structure of bovine mitochondrial F1-ATPase is described. Several features...approximately spherical alpha3beta3 sub-assembly. F1-ATPase|crystal structure|rotary catalysis...

2000-01-01T23:59:59.000Z

180

Unsteady-state material balance model for a continuous rotary dissolver  

SciTech Connect

The unsteady-state continuous rotary dissolver material balance code (USSCRD) is a useful tool with which to study the performance of the rotary dissolver under a wide variety of operating conditions. The code does stepwise continuous material balance calculations around each dissolver stage and the digester tanks. Output from the code consists of plots and tabular information on the stagewise concentration profiles of UO{sub 2}, PuO{sub 2}, fission products, Pu(NO{sub 3}){sub 4}, UO{sub 2}(NO{sub 3}){sub 2}, fission product nitrates, HNO{sub 3}, H{sub 2}O, stainless steel, total particulate, and total fuel in pins. Other information about material transfers, stagewise liquid volume, material inventory, and dissolution performance is also provided. This report describes the development of the code, its limitations, key operating parameters, usage procedures, and the results of the analysis of several sets of operating conditions. Of primary importance in this work was the estimation of the steady-state heavy metal inventory in a 0.5-t/d dissolver drum. Values ranging from {similar_to}12 to >150 kg of U + Pu were obtained for a variety of operating conditions. Realistically, inventories are expected to be near the lower end of this range. Study of the variation of operating parameters showed significant effects on dissolver product composition from intermittent solids feed. Other observations indicated that the cycle times for the digesters and shear feed should be closely coupled in order to avoid potential problems with off-specification product. 19 references, 14 tables.

Lewis, B.E.

1984-09-01T23:59:59.000Z

Note: This page contains sample records for the topic "indicators rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Mode localization results and laboratory demonstration techniques with a multi-pendulum rig  

E-Print Network (OSTI)

. Perturbed system mode shapes, analytical, for R' = 0. 015. 16 Table III. Perturbed system mode shapes, analytical, for R' = 0. 04 (K, = 0. 908 N-m/rad, 1, = 0, 532 m). 17 Table IV. Perturbed system mode shapes, analytical, for R' = 0. 15 (K, = 3. 90 N.... Pendulum rig schematic Figure 2. Detail of pendulum rig. Figure 3. Graphical depiction of mode shapes given in Table I. 10 Figure 4. Depiction of perturbed mode shapes given in Table's II, III, and IV for: (a) Rs=0. 015; (b) R =0. 04; and (c) R =0. 15...

Bollich, Robert Kenneth Gerard

1992-01-01T23:59:59.000Z

182

Electric Field Driven Torque in Biological Rotary Motors  

E-Print Network (OSTI)

Ion driven rotary motors, such as Fo-ATP synthase (Fo) and the bacterial flagellar motor, act much like a battery-powered electric motor. They convert energy from ions as they move from high to low potential across a membrane into torque and rotary motion. Here we propose a mechanism whereby electric fields, emanating from channels in one or more stators, act on asymmetric charge distributions due to protonated and deprotonated sites in the rotor and drive it to rotate. The model predicts an ideal scaling law between torque and ion motive force, which can be hindered by mitochondrial mutations. The rotor of Fo drives the gamma-subunit to rotate within the ATP-producing complex (F1), working against an opposing torque that rises and falls periodically with angular position. Drawing an analogy with Brownian motion of a particle in a tilted washboard potential, we compute the highly nonlinear ATP production rate vs. proton motive force (pmf), showing a minimum pmf needed to drive ATP production with important me...

Miller,, John H; Maric, Sladjana; Infante, Hans L; Claycomb, James R

2013-01-01T23:59:59.000Z

183

MICROHOLE TECHNOLOGY -PROGRESS ON BOREHOLE INSTRUMENTATION DEVELOPMENT  

E-Print Network (OSTI)

-sized commercial rigs, consists of a mechanical rotary bit, a hydraulically powered positive displacement motor

184

SERI Desiccant Cooling Test Facility. Status report. Preliminary data on the performance of a rotary parallel-passage silica-gel dehumidifier  

SciTech Connect

This report describes the SERI Desiccant Cooling Test Facility. The facility can test bench-scale rotary dehumidifiers over a wide range of controlled conditions. We constructed and installed in the test loop a prototype parallel-passage rotary dehumidifier that has spirally wound polyester tape coated with silica gel. The initial tests gave satisfactory results indicating that approximately 90% of the silica gel was active and the overall Lewis number of the wheel was near unity. The facility has several minor difficulties including an inability to control humidity satisfactorily and nonuniform and highly turbulent inlet velocities. To completely validate the facility requires a range of dehumidifier designs. Several choices are available including constructing a second parallel-passage dehumidifier with the passage spacing more uniform.

Schultz, K.J.

1986-04-01T23:59:59.000Z

185

Rigging a horse and rider: simulating the predictable and repetitive movement of the rider  

E-Print Network (OSTI)

setup. If an animation piece is only going to have a few shots with a horse and rider, then the trouble of setting up an automated character rig is not practical, but if there are a significant amount of shots with a horse and rider galloping across...

Kuhnel, Jennifer Lynn

2004-09-30T23:59:59.000Z

186

AbstractThe red snapper (Lutjanus campechanus) is currently under rig  

E-Print Network (OSTI)

653 Abstract­The red snapper (Lutjanus campechanus) is currently under rig orous federal and state of annuli in otolith thin sections have been used to age many species of fish, including red snapper. However, the utility of this method for aging red snapper has been questioned by those who dispute both

187

Department of Mechanical Engineering Fall 2009 Air Products-Entrained Particle Flow Test Rig  

E-Print Network (OSTI)

PENNSTATE Department of Mechanical Engineering Fall 2009 Air Products-Entrained Particle Flow Test are causing catalyst plugging. Objectives Air Products requested that a test rig be constructed to entrain the hydrogen reforming facilities and aid Air Products in understanding the plugging problem. Approach

Demirel, Melik C.

188

A Built for Purpose Micro-Hole Coiled Tubing Rig (MCTR)  

SciTech Connect

This report will serve as the final report on the work performed from the contract period October 2005 thru April 2007. The project 'A Built for Purpose Microhole Coiled Tubing Rig (MCTR)' purpose was to upgrade an existing state-of-the-art Coiled Tubing Drilling Rig to a Microhole Coiled Tubing Rig (MCTR) capable of meeting the specifications and tasks of the Department of Energy. The individual tasks outlined to meet the Department of Energy's specifications are: (1) Concept and development of lubricator and tool deployment system; (2) Concept and development of process control and data acquisition; (3) Concept and development of safety and efficiency improvements; and (4) Final unit integration and testing. The end result of the MCTR upgrade has produced a unit capable of meeting the following requirements: (1) Capable of handling 1-inch through 2-3/8-inch coiled tubing (Currently dressed for 2-3/8-inch coiled tubing and capable of running up to 3-1/2-inch coiled tubing); (2) Capable of drilling and casing surface, intermediate, production and liner hole intervals; (3) Capable of drilling with coiled tubing and has all controls and installation piping for a top drive; (4) Rig is capable of running 7-5/8-inch range 2 casing; and (5) Capable of drilling 5,000 ft true vertical depth (TVD) and 6,000 ft true measured depth (TMD).

Bart Patton

2007-09-30T23:59:59.000Z

189

Development of a Low-Cost Rotary Steerable Drilling System  

SciTech Connect

The project had the goal to develop and commercialize a low-cost rotary steerable system (LCRSS) capable of operating downhole at conventional pressures and temperatures to reduce operating costs by a minimum of 50% and lost-in-hole charges by at least 50% over the currently offered systems. The LCRSS system developed under this project does reduce operating costs by 55% and lost-in-hole charges by at least 50%. The developed product is not commercializable in its current form. The overall objective was to develop and commercialize a low cost rotary steerable system (LCRSS) capable of operating downhole at conventional pressures and temperatures (20,000 psi/150 C) while reducing the operating costs by 50% and the lost-in-hole charges by 50% over the currently available systems. The proposed reduction in costs were to be realized through the significant reduction in tool complexity, a corresponding increase in tool reliability as expressed in the mean-time between failure (MTBF), and a reduction in the time and costs required to service tools after each field operation. Ultimately, the LCRSS system was to be capable of drilling 7 7/8 in. to 9 5/8 in. borehole diameters. The project was divided into three Phases, of which Phases I & II were previously completed and reported on, and are part of the case file. Therefore, the previously reported information is not repeated herein. Phase III included the fabrication of two field ready prototypes that were to be subjected to a series of drilling tests at GTI Catoosa, DOE RMOTC, and at customer partnering wells, if possible, as appropriate in the timing of the field test objectives to fully exercise all elements of the LCRSS. These tests were conducted in an iterative process based on a performance/reliability improvement cycle with the goal of demonstrating the system met all aspects required for commercial viability. These tests were conducted to achieve continuous runs of 100+ hours with well trajectories that fully exercised the tool's build/turn/drop/hold target capabilities and its higher end ratings for bit weight, torque and rotary speed. The tool teardowns were rigorously analyzed at the conclusion of each field run to assess component wear rates and to fully document any detrimental behavior(s) observed.

Roney Nazarian

2012-01-31T23:59:59.000Z

190

Bailer for top head drive rotary well drills  

SciTech Connect

A bailer mounted to the derrick of a top head drive well drilling rig is described. The bailer includes a winch line drum mounted by a bracket to the derrick. A positive displacement hydraulic motor mounts one end of the drum and receives fluid under pressure from the existing hydraulic pressure supply. Valving is provided to allow reverse operation of the motor so equipment can either be raised or lowered relative to the derrick. The hydraulic delivery line to the motor includes a one way restrictor that will allow relatively free passage of fluid to the motor in a driving or lifting mode but will reverse flow of fluid from the motor, thereby affording a braking effect for lowering a load at a selected rate.

Bartholomew, L.

1980-09-23T23:59:59.000Z

191

CFD Simulation of Brine-Seawater Mixing in a Rotary Energy Recovery Device  

Science Journals Connector (OSTI)

CFD Simulation of Brine-Seawater Mixing in a Rotary Energy Recovery Device ... The effects of operational conditions on the mixing behavior of rotary energy recovery device have been systematically investigated through the combined methods of computational fluid dynamics and validating experiments in this paper. ... The obtained formulas between mixing and dimensionless flow length provide a simple way to calculate and predict the mixing of device, which will be beneficial to design and operate the rotary energy recovery device in a lower mixing level. ...

Enle Xu; Yue Wang; Liming Wu; Shichang Xu; Yuxin Wang; Shichang Wang

2014-11-05T23:59:59.000Z

192

TESTING OF THE SECOND GENERATION SPINTEK ROTARY FILTER -11357  

SciTech Connect

The SpinTek rotary microfilter has been developed under the Department of Energy (DOE) Office of Environmental Management (EM) for the purpose of deployment in radioactive service in the DOE complex. The unit that was fabricated and tested is the second generation of the filter that incorporates recommended improvements from previous testing. The completion of this test satisfied a key milestone for the EM technology development program and technology readiness for deployment by Savannah River Remediation in the Small Column Ion Exchange and Sludge Washing processes at the Savannah River Site (SRS). The Savannah River National Laboratory (SRNL) contracted SpinTek Filtration to fabricate a full scale 25 disk rotary filter and perform a 1000 hour endurance test with a simulated SRS sludge. Over 1500 hours of operation have been completed with the filter. SpinTek Filtration fabricated a prototypic 25 disk rotary filter including updates to manufacturing tolerances, an updated design to the rotary joint, improved cooling to the bottom journal, decreases in disk and filter shaft hydraulic resistances. The filter disks were fabricated with 0.5 {micro} pore size, sintered-metal filter media manufactured by Pall Corporation (M050). After fabrication was complete, the filter passed acceptance tests demonstrating rejection of solids and clean water flux with a 50% improvement over the previous filters. Once the acceptance test was complete, a 1000 hour endurance test was initiated simulating a sludge washing process. The test used a simulated SRS Sludge Batch 6 recipe. The insoluble solids started at 5 wt% and were raised to 10 and 15 wt% insoluble solids to simulate the concentration of a large volume tank. The filter system was automated and set up for 24 hour unattended operation. To facilitate this, process control logic was written to operate the filter. During the development it was demonstrated that the method of starting and stopping the filter can affect the build up of filter cake on the disks and therefore the performance of the filter. The filter performed well with the simulant. Very little drop in production was noticed between the 5 and 10 wt% insoluble solids feed. Increasing to 15 wt% had a more pronounced impact due to the rheology of the feed. Acid cleaning was used to clean the filter disks in-situ and restore filtration rate to almost 90% of the initial clean disk rate. Eighty liters of 0.2 M nitric acid in conjunction with water rinses were used to clean the filter in less than 2 hours. Filter testing was completed after 1000 hours of operation were performed on the final filter assembly configuration. The total run time for the testing was over 1500 hours. At the end of the test, the sludge washing was performed successfully from approximately 5.6 M to less than 1 M sodium.

Herman, D.; Poirier, M.; Fowley, M.; Keefer, M.; Huff, T.

2011-02-02T23:59:59.000Z

193

Theoretical and experimental study on regenerative rotary displacer Stirling engine  

SciTech Connect

Recently a quite new type of hot air engine called rotary displacer engine, in which the displacer is a rotating disk enclosed in a cylinder, has been conceived and developed. The working gas, contained in a notch excavated in the disk, is heated and cooled alternately, on account of the heat transferred through the enclosing cylinder that is heated at one side and cooled at the opposite one. The gas temperature oscillations cause the pressure fluctuations that get out mechanical power acting on a power piston. In order to attempt to increase the performances for this kind of engine, the authors propose three different regeneration methods. The first one comprises two coaxial disks that, revolving in opposite ways, cause a temperature gradient on the cylinder wall and a regenerative axial heat conduction through fins shaped on the cylinder inner wall. The other two methods are based on the heat transferred by a proper closed circuit that in one case has a circulating liquid inside and in the other one is formed by several heat pipes working each one for different temperatures. An engine based on the first principle, the Regenerative Tandem Contra-Rotary Displacer Stirling Engine, has been realized and experimented. In this paper experimental results with and without regeneration are reported comparatively with a detailed description of the unity. A basic explanation of the working principle of this engine and a theoretical analysis investigating the main influential parameters for the regenerative effect are done. This new rotating displacer Stirling engines, for their simplicity, are expected to attain high rotational speed especially for applications as demonstration and hobby unities.

Raggi, L.; Katsuta, Masafumi [Waseda Univ., Tokyo (Japan); Isshiki, Naotsugu [Nihon Univ., Tokyo (Japan); Isshiki, Seita [Isshiki R and D Lab., Tokyo (Japan)

1997-12-31T23:59:59.000Z

194

Marcellus Shale Drilling and Hydraulic Fracturing; Technicalities and  

E-Print Network (OSTI)

Pipe · Air Rotary Drilling Rig · Hydraulic Rotary Drilling Rig ­ Barite/Bentonite infused drilling muds A "Thumper Truck" #12;Rigging Up #12;Drilling · The Drill String ­ Diesel Powered ­ Drilling Bit ­ Drilling

Jiang, Huiqiang

195

Climate Indices  

NLE Websites -- All DOE Office Websites (Extended Search)

Indices Indices Climate Indices Climate indices are diagnostic tools used to describe the state of the climate system and monitor climate. They are most often represented with a time series, where each point in time corresponds to one index value. An index can be constructed to describe almost any atmospheric event; as such, they are myriad. Therefore, CDIAC provides these links to other web sites to help guide users to the most widely used climate indices, which in many cases are updated monthly. Data Set Website/Name NOAA's Climate Prediction Center, Monitoring and Data Index Page NOAA's Earth Systems Research Laboratory, Monthly Atmospheric and Ocean Time Series Page (plot, analyze, and compare time series) The Monthly Teleconnection Indices Page from NOAA's National

196

Calculation of the geometric parameters of rotary rolling by using the automated design system autodesk inventor  

Science Journals Connector (OSTI)

A method is proposed for calculating the profile of the rolls of a rotary rolling mill with the use of the 3D-modeling program Autodesk Inventor. The universality of the method is...

S. M. Gorbatyuk; V. A. Osadchii; E. Z. Tuktarov

2011-11-01T23:59:59.000Z

197

Method for determining effective flame emissivity in a rotary kiln incinerator burning solid waste  

Science Journals Connector (OSTI)

Temperature is the most important parameter for the improvement of combustion efficiency and the control of pollutants. In order to obtain accurate flame temperatures in a rotary kiln incinerator using non-int...

Jin-cai Du; Qun-xing Huang; Jian-hua Yan

2012-12-01T23:59:59.000Z

198

James Walker develops Walkersele D8 – a new rotary lip seal for marine propulsion systems  

Science Journals Connector (OSTI)

Walkersele D8 is a new design of rotary lip seal developed by James Walker & Co Ltd for use in marine propulsion systems to protect bearings from water ingress or prevent lubricant from leaking into the marine environment.

2012-01-01T23:59:59.000Z

199

Rotary Triboelectric Nanogenerator Based on a Hybridized Mechanism for Harvesting Wind Energy  

Science Journals Connector (OSTI)

Rotary Triboelectric Nanogenerator Based on a Hybridized Mechanism for Harvesting Wind Energy ... Triboelectric nanogenerator (TENG) is a simple, cost-effective, and highly efficient approach for generating electricity from mechanical energies in a wide range of forms. ...

Yannan Xie; Sihong Wang; Long Lin; Qingshen Jing; Zong-Hong Lin; Simiao Niu; Zhengyun Wu; Zhong Lin Wang

2013-06-14T23:59:59.000Z

200

A Ceramic Waste Heat Recovery System on a Rotary Forge Furnace: An Installation and Operating History  

E-Print Network (OSTI)

heavy duty high temperature ceramic tube recuperator and five high temperature recirculating burners. The energy conservation system was retrofitted onto a rotary hearth furnace with an inside diameter of 11' 5'' (3.5m) and an available hearth area...

Young, S. B.; Campbell, T. E.; Worstell, T. M.

1981-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "indicators rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Rigging skeletal perissodactyl and artiodactyl ungulate limbs using analytic inverse kinematic-based solutions for a feature film production environment  

E-Print Network (OSTI)

The goal of this thesis is to develop and construct a repeatable, scalable, and portable rigging solution for the skeletal limbs of ungulates, maximizing functionality while streamlining intuitive interface controls for a feature film production...

Telford, William Lawrence, Jr

2007-04-25T23:59:59.000Z

202

A test rig for the identification of rotordynamic coefficients of fluid film bearings  

E-Print Network (OSTI)

. The test bearing articles were considered for cryogenic applications where the actual lubrication medium is liquid hydrogen or liquid oxygen. The parameter identification method used an advanced pseudo-random forcing excitation and a technique based...A TEST RIG FOR THE IDENTIFICATION OF ROTORDYNAMIC COEFFICIENTS OF FLUID FILM BEARINGS A Thesis LEWIS MILLER ROBISON III Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment of the requirements...

Robison, Lewis Miller

1995-01-01T23:59:59.000Z

203

Large scale test rig for flow visualization and leakage measurement of labyrinth seals  

E-Print Network (OSTI)

number. Heffner (1959) measured the leakage rates of air through stationary true size labyrinth seals with the goal of predicting leakage rates for new seal designs through correlation charts developed from his investigation. Leakage resistance... geometries and land surfaces with the objective of obtaining optimized seal design criteria. The test rig utilized a flat two-dimensional stationary seal with a radial clearance-to-width ratio of approximately 100:1 to reduce wall end effects. Air...

Broussard, Daniel Harold

2012-06-07T23:59:59.000Z

204

Design of a new type of rotary Stirling engine  

SciTech Connect

The Stirling machine has had wide diffusion only in cold or cryogenic applications (Philips) while the engine, despite big efforts of large Companies (Philips, Westinghouse, General Motors, etc.), never definitively reached the market; today new interest is raised correlated with environmental and energy related considerations. Thus, researchers efforts are addressed towards the design of innovative and more competitive Stirling engine configurations, like the one here proposed. This paper describes the configuration of a new, rotary Stirling engine. In the cold part of the engine, the working fluid is compressed by a rotating element, then it passes through the regenerator from the cold to the hot end, where it absorbs the heat and expands in the high pressure and temperature area. The high pressure working fluid pushes on the rotating element (the so called rotator) and the engine outputs power. In the design, compression and expansion volumes change with the rotation. Two rotators are connected with a set of gears: therefore, the engine transmission system is simplified and dimensions are reduced.

Abenavoli, R.I.; Dong, W.; Fedele, L.; Sciaboni, A. [Univ. La Sapienza, Rome (Italy). Dipt. di Meccanica e Aeronautica

1996-12-31T23:59:59.000Z

205

Sway control method and system for rotary cranes  

DOE Patents (OSTI)

Methods and apparatuses for reducing the oscillatory motion of rotary crane payloads during operator-commanded or computer-controlled maneuvers. An Input-shaping filter receives input signals from multiple operator input devices and converts them into output signals readable by the crane controller to dampen the payload tangential and radial sway associated with rotation of the jib. The input signals are characterized by a hub rotation trajectory .gamma.(t), which includes a jib angular acceleration .gamma., a trolley acceleration x, and a load-line length velocity L. The system state variables are characterized by a tangential rotation angle .theta.(t) and a radial rotation angle .phi.(t) of the load-line. The coupled equations of motion governing the filter are non-linear and configuration-dependent. In one embodiment, a filter is provided between the operator and the crane for filtering undesired frequencies from the angular .gamma. and trolley x velocities to suppress payload oscillation. In another embodiment, crane commands are computer generated and controlled to suppress vibration of the payload using a postulated asymmetrical shape for the acceleration profiles of the jib, which profiles are uniquely determined by a set of parameters (including the acceleration pulse amplitude and the duration and coast time between pulses), or a dynamic programming approach.

Robinett, Rush D. (Tijeras, NM); Parker, Gordon G. (Houghton, MI); Feddema, John T. (Albuquerque, NM); Dohrmann, Clark R. (Albuquerque, NM); Petterson, Ben J. (Albuquerque, NM)

1999-01-01T23:59:59.000Z

206

Rotary seal with enhanced lubrication and contaminant flushing  

DOE Patents (OSTI)

A resilient, ring shaped interference-type hydrodynamic rotary seal having waves on the lubricant side which provide increased film thickness and flushing action by creating contact pressure induced angulated restrictions formed by abrupt restrictive diverters. The angulated restrictions are defined by projecting ridges, corners at the trailing edge of the waves, or simply by use of a converging shape at the trailing edge of the waves which is more abrupt than the gently converging hydrodynamic inlet shape at the leading edge of the waves. The abrupt restrictive diverter performs two functions; a restricting function and a diverting function. The angulated restrictions cause a local film thickness restriction which produces a damming effect preventing a portion of the lubricant from leaking out of the dynamic sealing interface at the trailing edge of the wave, and results in a much thicker lubricant film thickness under the waves. This contributes to more film thickness in the remainder of the dynamic sealing interface toward the environment because film thickness tends to decay gradually rather than abruptly due to the relative stiffness of the seal material. Because of the angle of the abrupt restrictive diverter relative to the relative rotation direction, in conjunction with the restriction or damming effect, a strong diverting action is produced which pumps lubricant across the dynamic sealing interface toward the environment. The lubricant diversion is caused by the component of the rotational velocity tangent to the abrupt restrictive diverter. The component of rotational velocity normal to the abrupt restrictive diverter causes a portion of the lubricant film to be pumped past the abrupt restrictive diverter, thereby assuring adequate lubrication thereof.

Dietle, Lannie L. (Sugar Land, TX)

2000-01-01T23:59:59.000Z

207

Factors influencing the incidence rates of injuries and accidents among seafarers and rig workers providing support to the WA offshore oil and gas industry.  

E-Print Network (OSTI)

??The aim of this study was to identify, discuss and make recommendations regarding causal factors associated with injuries and accidents among seafarers and rig workers… (more)

Martinovich, Tony, Dr

2013-01-01T23:59:59.000Z

208

HumanWildlife Interactions 8(2):251260, Fall 2014 Wildlife strikes with U.S. military rotary-  

E-Print Network (OSTI)

, but unstudied, physical hazard to military rotary-wing aircraft used in conducting overseas flight operations to military rotary-wing aircraft during these operations has been conducted. The objectives of this project deployed overseas to conduct a variety of noncombat and combat missions. Our objective was to conduct

209

Continuous injection of an inert gas through a drill rig for drilling into potentially hazardous areas  

SciTech Connect

A drill rig for drilling in potentially hazardous areas includes a drill having conventional features such as a frame, a gear motor, gear box, and a drive. A hollow rotating shaft projects through the drive and frame. An auger, connected to the shaft is provided with a multiplicity of holes. An inert gas is supplied to the hollow shaft and directed from the rotating shaft to the holes in the auger. The inert gas flows down the hollow shaft, and then down the hollow auger, and out through the holes in the bottom of the auger into the potentially hazardous area.

McCormick, S.H.; Pigott, W.R.

1998-04-01T23:59:59.000Z

210

An introduction to API 682 shaft sealing for centrifugal and rotary pumps  

SciTech Connect

Seal failures in refineries represents between 5,000 and 10,000 dollars in maintenance costs. The lack of an industry standard approach has resulted in high-stocking cost, high maintenance costs, and complicated populations of seals. The API has offered API 682, Shaft Sealing Systems for Centrifugal and Rotary Pumps. This report discusses the benefits of API 682.

Dufour, J.W. [Amoco Oil Company, Chicago, IL (United States); Jones, R.L. [Shell Oil Company, Houston, TX (United States)

1994-11-01T23:59:59.000Z

211

Operability test report for rotary mode core sampling system number 3  

SciTech Connect

This report documents the successful completion of operability testing for the Rotary Mode Core Sampling (RMCS) system {number_sign}3. The Report includes the test procedure (WHC-SD-WM-OTP-174), exception resolutions, data sheets, and a test report summary.

Corbett, J.E.

1996-03-01T23:59:59.000Z

212

DOI-BLM-CA-670-2010-107 | Open Energy Information  

Open Energy Info (EERE)

a normal rotary drilling rig. The rig will be equipped with diesel engines, storage tanks, mud pumps, and other typical auxiliary equipment During drilling, the top of the...

213

EIA - Natural Gas Exploration & Reserves Data and Analysis  

Gasoline and Diesel Fuel Update (EIA)

natural gas, and lease condensate (annual). Crude Oil and Natural Gas Drilling Activity Rotary rigs in operation, footage drilled, and active well service rig counts (monthly,...

214

Department of Mechanical Engineering Spring 2010 Kenya Water Well Drill Rig Redesign of Engine Drive Train System & Support Tower  

E-Print Network (OSTI)

of Engine Drive Train System & Support Tower Overview The team was presented with the task of redesigning the engine drive train system and support structure for a water drill rig to be used in Kenya. The original engine drive train system was fabricated by a professional machinist and had many intricate components

Demirel, Melik C.

215

Design and Analysis of a Test Rig for Modeling the Bit/Formation Interface in Petroleum Drilling Applications  

E-Print Network (OSTI)

and horizontal wells and measuring the effects of various factors on the stability of perturbations on the system. A test rig concept has been developed to accurately measure the interaction forces and torques between the bit, formation and fluids during drilling...

Wilson, Joshua Kyle

2013-04-11T23:59:59.000Z

216

Small mill for the high-temperature rotary rolling of semifinished products composed of refractory metals in protective media  

Science Journals Connector (OSTI)

A description is presented of a small vacuum-type rotary rolling mill designed for the high-temperature deformation of semifinished products to obtain bars 7–10 mm in diameter. It is shown that the CAD software Autodesk

S. M. Gorbatyuk; E. Z. Tuktarov; L. A. Rudenskii

2012-01-01T23:59:59.000Z

217

Natural Gas Weekly Update  

NLE Websites -- All DOE Office Websites (Extended Search)

Natural Gas Rotary Rig Count Rises to Highest Level since February 2009. The natural gas rotary rig count was 992 as of Friday, August 13, according to data released by Baker...

218

TESTING OF A FULL-SCALE ROTARY MICROFILTER FOR THE ENHANCED PROCESS FOR RADIONUCLIDES REMOVAL  

SciTech Connect

Savannah River National Laboratory (SRNL) researchers are investigating and developing a rotary microfilter for solid-liquid separation applications in the Department of Energy (DOE) complex. One application involves use in the Enhanced Processes for Radionuclide Removal (EPRR) at the Savannah River Site (SRS). To assess this application, the authors performed rotary filter testing with a full-scale, 25-disk unit manufactured by SpinTek Filtration with 0.5 micron filter media manufactured by Pall Corporation. The filter includes proprietary enhancements by SRNL. The most recent enhancement is replacement of the filter's main shaft seal with a John Crane Type 28LD gas-cooled seal. The feed material was SRS Tank 8F simulated sludge blended with monosodium titanate (MST). Testing examined total insoluble solids concentrations of 0.06 wt % (126 hours of testing) and 5 wt % (82 hours of testing). The following are conclusions from this testing.

Herman, D; David Stefanko, D; Michael Poirier, M; Samuel Fink, S

2009-01-01T23:59:59.000Z

219

Understanding the Dynamics Behind the Photoisomerization of a Light-Driven Fluorene Molecular Rotary Motor  

Science Journals Connector (OSTI)

In the present contribution we report a combined quantum chemical and molecular dynamics study of the mechanism of the rotational cycle of the fluorene-based molecular rotary motor 9-(2,4,7-trimethyl-2,3-dihydro-1H-inden-1-ylidene)-9H-fluorene (1). ... (41) The theoretical results obtained hold considerable implications in achieving a rational synthetic design of future molecular motors with application defined functionality. ...

Andranik Kazaryan; Jos C. M. Kistemaker; Lars V. Scha?fer; Wesley R. Browne; Ben L. Feringa; Michael Filatov

2010-03-29T23:59:59.000Z

220

A thermodynamic analysis of the rotary-vee internal combustion engine  

E-Print Network (OSTI)

OF FIGURES FIGURE 1. IC Engine Family Tree FIGURE 2. Three Possibilities of Single Rotation Machines (SIM) . . . . . Page FIGURE 3 Planetary Rotor Motion and Path of the Apex Seal for the Wankel Engine 10 FIGURE 4. Cut-Away View of the Rand Cam Engine... for the Rotary-Vee Engine 24 FIGURE 9. Overall View of Piston And Cylinder Block Configuration, . . . FIGURE 10. Overall View Showing the Central Cavity . . . . . . . . . . . . . . . . . . . . . . . . . . . FIGURE 11. Sectioned View of the Pistons...

Bailey, Stephen Glenn

2012-06-07T23:59:59.000Z

Note: This page contains sample records for the topic "indicators rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Manipulator having thermally conductive rotary joint for transferring heat from a test specimen  

DOE Patents (OSTI)

A manipulator for rotatably moving a test specimen in an ultra-high vacuum chamber includes a translational unit movable in three mutually perpendicular directions. A manipulator frame is rigidly secured to the translational unit for rotatably supporting a rotary shaft. A first copper disc is rigidly secured to an end of the rotary shaft for rotary movement within the vacuum chamber. A second copper disc is supported upon the first disc. The second disc receives a cryogenic cold head and does not rotate with the first disc. A sapphire plate is interposed between the first and second discs to prevent galling of the copper material while maintaining high thermal conductivity between the first and second discs. A spring is disposed on the shaft to urge the second disc toward the first disc and compressingly engage the interposed sapphire plate. A specimen mount is secured to the first disc for rotation within the vacuum chamber. The specimen maintains high thermal conductivity with the second disc receiving the cryogenic transfer line.

Haney, Steven J. (Tracy, CA); Stulen, Richard H. (Livermore, CA); Toly, Norman F. (Livermore, CA)

1985-01-01T23:59:59.000Z

222

Pitch deviation measurement of an involute spur gear by a rotary profiling system  

Science Journals Connector (OSTI)

Abstract This paper presents surface-profiling based gear pitch deviation measurement for an involute spur gear. A rotary profiling system, which consists of an air-bearing spindle and a displacement sensor with a diamond stylus, is employed to measure gear pitch deviation. In measurement of gear pitch deviation, an eccentric error between a gear axis and a motion axis of the rotary stage in the profiling system would affect accuracy of gear profile measurement. In this paper, at first, the influence of the eccentric error on measurement of gear pitch deviation is estimated in computer simulation based on a geometric model of the profiling system. After that, a new scanning method named “opposite-direction dual scanning method” is proposed so that a steep profile of gear flank surface with a local slope of up to 90° can be measured by the developed rotary profiling system. For compensating distortions in the measured gear tooth profile, which are induced not only by the eccentric error but also by a probe offset introduced by the proposed scanning method, a self-calibration and compensation method is applied. To verify the feasibility of the proposed method, measurement of gear pitch deviation of a master involute spur gear with a certificate data is carried out. Measurement uncertainty of the proposed method is also analyzed.

Bin Xu; Yuki Shimizu; So Ito; Wei Gao

2014-01-01T23:59:59.000Z

223

Manipulator having thermally conductive rotary joint for transferring heat from a test specimen  

DOE Patents (OSTI)

A manipulator for rotatably moving a test specimen in an ultra-high vacuum chamber includes a translational unit movable in three mutually perpendicular directions. A manipulator frame is rigidly secured to the translational unit for rotatably supporting a rotary shaft. A first copper disc is rigidly secured to an end of the rotary shaft for rotary movement within the vacuum chamber. A second copper disc is supported upon the first disc. The second disc receives a cryogenic cold head and does not rotate with the first disc. The second disc receives a cryogenic cold head and does not rotate with the first disc. A sapphire plate is interposed between the first and second discs to prevent galling of the copper material while maintaining high thermal conductivity between the first and second discs. A spring is disposed on the shaft to urge the second disc toward the first disc and compressingly engage the interposed sapphire plate. A specimen mount is secured to the first disc for rotation within the vacuum chamber. The specimen maintains high thermal conductivity with the second disc receiving the cryogenic transfer line.

Haney, S.J.; Stulen, R.H.; Toly, N.F.

1983-05-03T23:59:59.000Z

224

U.S. Energy Information Administration (EIA)  

Annual Energy Outlook 2012 (EIA)

the 5-year average. The total rig count was 1,769, up 12 from a year ago.The natural gas rotary rig count totaled 335 as of February 28, which represents a decline of 7 rigs from...

225

Driven dynamics and rotary echo of a qubit tunably coupled to a harmonic oscillator  

E-Print Network (OSTI)

We have investigated the driven dynamics of a superconducting flux qubit that is tunably coupled to a microwave resonator. We find that the qubit experiences an oscillating field mediated by off-resonant driving of the resonator, leading to strong modifications of the qubit Rabi frequency. This opens an additional noise channel, and we find that low-frequency noise in the coupling parameter causes a reduction of the coherence time during driven evolution. The noise can be mitigated with the rotary-echo pulse sequence, which, for driven systems, is analogous to the Hahn-echo sequence.

Gustavsson, Simon; Yan, Fei; Forn-Díaz, Pol; Bolkhovsky, Vlad; Braje, Danielle; Fitch, George; Harrabi, Khalil; Lennon, Donna; Miloshi, Jovi; Murphy, Peter; Slattery, Rick; Spector, Steven; Turek, Ben; Weir, Terry; Welander, Paul B; Yoshihara, Fumiki; Cory, David G; Nakamura, Yasunobu; Orlando, Terry P; Oliver, William D

2012-01-01T23:59:59.000Z

226

A model of stepping kinetics for rotary enzymes. Application to the F1-ATPase  

Science Journals Connector (OSTI)

Our simple kinetic model, based on the classic “binding change mechanism”, describes the stepping kinetics for the rotary enzyme motors. The model shows that the cooperative interactions between active sites in the motor enzyme F1-ATPase induce the stepping product release. This phenomenon results from non-harmonic oscillations in the enzyme forms. The found rate constants, corresponding to the stepping phenomenon, are close to the rate constants known for the F1-ATPase. The duration of dwells during the product release is shown to depend on the ATP concentration in accordance with the known experimental data.

B.N. Goldstein; A.M. Aksirov; D.T. Zakrjevskaya

2011-01-01T23:59:59.000Z

227

Word Pro - S5  

U.S. Energy Information Administration (EIA) Indexed Site

Crude Oil and Natural Gas Resource Development Indicators Rotary Rigs in Operation by Type, 1949-2012 Rotary Rigs in Operation by Type, Monthly Active Well Service Rig Count, Monthly Total Wells Drilled by Type, 1949-2010 . 76 U.S. Energy Information Administration / Monthly Energy Review November 2013 Total 1950 1955 1960 1965 1970 1975 1980 1985 1990 1995 2000 2005 2010 0 1 2 3 4 Thousand Rigs 1950 1955 1960 1965 1970 1975 1980 1985 1990 1995 2000 2005 2010 0 10 20 30 40 50 Thousand Wells Dry Wells Crude Oil Wells Web Page: http://www.eia.gov/totalenergy/data/monthly/#crude. Sources: Tables 5.1 and 5.2. Crude Oil J FMAMJ J A SOND J FMAMJ J A SOND J FMAMJ J

228

Word Pro - S5  

U.S. Energy Information Administration (EIA) Indexed Site

Crude Oil and Natural Gas Crude Oil and Natural Gas Resource Development Figure 5.1 Crude Oil and Natural Gas Resource Development Indicators Rotary Rigs in Operation by Type, 1949-2012 Rotary Rigs in Operation by Type, Monthly Active Well Service Rig Count, Monthly Total Wells Drilled by Type, 1949-2010 . 76 U.S. Energy Information Administration / Monthly Energy Review November 2013 Total 1950 1955 1960 1965 1970 1975 1980 1985 1990 1995 2000 2005 2010 0 1 2 3 4 Thousand Rigs 1950 1955 1960 1965 1970 1975 1980 1985 1990 1995 2000 2005 2010 0 10 20 30 40 50 Thousand Wells Dry Wells Crude Oil Wells Web Page: http://www.eia.gov/totalenergy/data/monthly/#crude. Sources: Tables 5.1 and 5.2.

229

A stochastic penetration rate model for rotary drilling in surface mines  

Science Journals Connector (OSTI)

Abstract Principal Component Analysis (PCA) is used to determine the most effective parameters on the rock mass penetrability by considering their variance ratio in the first principal component. A model is developed for the prediction of rotary drills penetration rate using non-linear multiple regression analysis. Distribution functions for the effective parameters are calculated using measured data from two case studies. Applying the developed penetration rate model, a stochastic analysis is carried out using the Monte Carlo simulation. The proposed method provides a simple and effective assessment of the variability of the penetration rate model and its dependent parameters. Results showed that the PCA and Monte Carlo are suitable techniques for modeling and assessing the variability of rock mass penetrability parameters. According to the developed distribution model, with 90% of confidence level the penetration rate values range 0.2–2.5 m/min, which shows the wide possible range of penetration rates for rotary drilling especially in sedimentary (limestone and sandstone bearing magnetite mineral of Golgohar mine) and Sarcheshmeh igneous porphyry rock masses.

Omid Saeidi; Seyed Rahman Torabi; Mohammad Ataei; Jamal Rostami

2014-01-01T23:59:59.000Z

230

Thermal modeling of core sampling in flammable gas waste tanks. Part 2: Rotary-mode sampling  

SciTech Connect

The radioactive waste stored in underground storage tanks at Hanford site includes mixtures of sodium nitrate and sodium nitrite with organic compounds. The waste can produce undesired violent exothermic reactions when heated locally during the rotary-mode sampling. Experiments are performed varying the downward force at a maximum rotational speed of 55 rpm and minimum nitrogen purge flow of 30 scfm. The rotary drill bit teeth-face temperatures are measured. The waste is simulated with a low thermal conductivity hard material, pumice blocks. A torque meter is used to determine the energy provided to the drill string. The exhaust air-chip temperature as well as drill string and drill bit temperatures and other key operating parameters were recorded. A two-dimensional thermal model is developed. The safe operating conditions were determined for normal operating conditions. A downward force of 750 at 55 rpm and 30 scfm nitrogen purge flow was found to yield acceptable substrate temperatures. The model predicted experimental results reasonably well. Therefore, it could be used to simulate abnormal conditions to develop procedures for safe operations.

Unal, C.; Poston, D.; Pasamehmetoglu, K.O. [Los Alamos National Lab., NM (United States). Nuclear Systems Design and Analysis Group; Witwer, K.S. [Westinghouse Hanford Co., Richland, WA (United States). Engineering Testing Lab.

1997-08-01T23:59:59.000Z

231

Operability test procedure for rotary mode core sampling system {number_sign}3  

SciTech Connect

This document gives instructions for the Operability Testing of the Rotary Mode Core Sampling (RMCS) System No. 3. This document is based on the Operability Test Procedure for RMCS system No. 2 because the basic design is the same for all three systems. Modifications have been made from the original design only when exact duplication was not feasible or design improvements could be incorporated without affecting the operation of the system. Operability testing of the Rotary Mode Core Sampling System No. 3, will verify that functional and operational requirements have been met. Testing will be completed in two phases. The first phase of testing (section 7) will involve operating the truck equipment to demonstrate its capabilities. The second phase of testing (section 8) will take repeated samples in a simulated operation environment. These tests will be conducted at the ``Rock Slinger`` test site located just south of U-Plant in the 200 West Area. Tests will be done in a simulated tank farm environment. All testing will be non-radioactive and stand-in materials shall be used to simulate waste tank conditions. Systems will be assembled and arranged in a manner similar to that expected in the field.

Farris, T.R.; Jarecki, T.D.

1995-04-26T23:59:59.000Z

232

Operability test procedure for rotary mode core sampling system {number_sign}4  

SciTech Connect

This document gives instructions for the Operability Testing of the Rotary Mode Core Sampling (RMCS) System No. 4. This document is based on the Operability Test Procedure for RMCS system No. 2 because the basic design is the same for all three systems. Modifications have been made from the original design only when exact duplication was not feasible or design improvements could be incorporated without affecting the operation of the system. Operability testing of the Rotary Mode Core Sampling System No. 4 will verify that functional and operational requirements have been met. Testing will be completed in two phases. The first phase of testing (section 7) will involve operating the truck equipment to demonstrate its capabilities. The second phase of testing (section 8) will take repeated samples in a simulated operation environment. These tests will be conducted at the ``Rock Slinger`` test site located just south of U-Plant in the 200 West Area. Tests will be done in a simulated tank farm environment. All testing will be non-radioactive and stand-in materials shall be used to simulate waste tank conditions. Systems will be assembled and arranged in a manner similar to that expected in the field.

Farris, T.R.; Jarecki, T.D.

1995-04-26T23:59:59.000Z

233

Baseline Design Compliance Matrix for the Rotary Mode Core Sampling System  

SciTech Connect

The purpose of the design compliance matrix (DCM) is to provide a single-source document of all design requirements associated with the fifteen subsystems that make up the rotary mode core sampling (RMCS) system. It is intended to be the baseline requirement document for the RMCS system and to be used in governing all future design and design verification activities associated with it. This document is the DCM for the RMCS system used on Hanford single-shell radioactive waste storage tanks. This includes the Exhauster System, Rotary Mode Core Sample Trucks, Universal Sampling System, Diesel Generator System, Distribution Trailer, X-Ray Cart System, Breathing Air Compressor, Nitrogen Supply Trailer, Casks and Cask Truck, Service Trailer, Core Sampling Riser Equipment, Core Sampling Support Trucks, Foot Clamp, Ramps and Platforms and Purged Camera System. Excluded items are tools such as light plants and light stands. Other items such as the breather inlet filter are covered by a different design baseline. In this case, the inlet breather filter is covered by the Tank Farms Design Compliance Matrix.

LECHELT, J.A.

2000-10-17T23:59:59.000Z

234

Stress intensity factors and fatigue growth of a surface crack in a drill pipe during rotary drilling operation  

E-Print Network (OSTI)

known that drill pipe fatigue in oil-gas drilling operations represents more than 30% of the drill pipeStress intensity factors and fatigue growth of a surface crack in a drill pipe during rotary drilling operation Ngoc Ha Daoa, , Hedi Sellamia aMines ParisTech, 35 rue Saint-Honoré, 77305 Fontainebleau

Paris-Sud XI, Université de

235

Design Review Report for formal review of safety class features of exhauster system for rotary mode core sampling  

SciTech Connect

Report documenting Formal Design Review conducted on portable exhausters used to support rotary mode core sampling of Hanford underground radioactive waste tanks with focus on Safety Class design features and control requirements for flammable gas environment operation and air discharge permitting compliance.

JANICEK, G.P.

2000-06-08T23:59:59.000Z

236

A finite volume method and experimental study of a stator of a piezoelectric traveling wave rotary ultrasonic motor  

E-Print Network (OSTI)

circuit for the stator of a piezo- electric traveling wave rotary ultrasonic motor is presented ultrasonic motor V. Bolborici a, , F.P. Dawson b , M.C. Pugh c a University of Texas at El Paso, Department of Electrical and Computer Engineering, 500 W. University Ave., El Paso, TX 79968, USA b University of Toronto

Pugh, Mary

237

Combustion of high-sulfur coal and anthracite wastes in a rotary kiln combustor with an advanced internal air distributor  

SciTech Connect

Fluid bed combustors have received extensive testing with both high-sulfur coal and anthracite wastes. Rotary kilns are effective and popular devices for waste combustion. The Angelo Rotary Furnace{trademark} has been developed to improve the operation of rotary pyrolyzer/combustor systems through enhanced air distribution, which in this process is defined as staged, swirled combustion air injection. Fourteen of these new furnaces have been installed worldwide. Two units in Thailand, designed for rice hull feed with occasional lignite feed, have been recently started up. An older unit in Pennsylvania is being upgraded with a new, more advanced air distribution system for a series of tests this fall in which inexpensive high-sulfur coal and anthracite wastes will be fired with limestone. The purposes of these tests are to determine the burning characteristics of these two fuels in this system, to discover the Ca/S ratios necessary for operation of a rotary kiln combusting these fuels, and to observe the gas-borne emissions from the furnace. An extensive preliminary design study will be performed on a commercial installation for combustion of anthracite wastes. 14 refs., 5 figs., 1 tab.

Cobb, J.T. Jr. (Pittsburgh Univ., PA (USA)); Ahn, Y.K. (Gilbert/Commonwealth, Inc., Reading, PA (USA)); Angelo, J.F. (Universal Energy International, Inc., Little Rock, AR (USA))

1990-01-01T23:59:59.000Z

238

BID NO: SKA SSLE 009/2011 SUPPLY, DELIVERY AND INSTALLATION OF ROTARY UPS, MV INDOOR SWITCHGEAR AND  

E-Print Network (OSTI)

, and dry-type power transformers only ­ no alternative offers in this regard will be accepted. The contract SWITCHGEAR AND POWER TRANSFORMERS AT THE MeerKAT SITE NEAR CARNARVON, NORTHERN CAPE TENDER NOTICE and Installation of Rotary UPS, MV Indoor Switchgear and Power Transformers at the MeerKAT Site near Carnarvon

Jarrett, Thomas H.

239

TRAC-PF1/MOD3 calculations of Savannah River Laboratory Rig FA single-annulus heated experiments  

SciTech Connect

This paper presents the results of TRAC-PF1/MOD3 benchmarks of the Rig FA experiments performed at the Savannah River Laboratory to simulate prototypic reactor fuel assembly behavior over a range of fluid conditions typical of the emergency cooling system (ECS) phase of a loss-of-coolant accident (LOCA). The primary purpose of this work was to use the SRL Rig FA tests to qualify the TRAC-PF1/MOD3 computer code and models for computing Mark-22 fuel assembly LOCA/ECS power limits. This qualification effort was part of a larger effort undertaken by the Los Alamos National Laboratory for the US Department of Energy to independently confirm power limits for the Savannah River Site K Reactor. The results of this benchmark effort as discussed in this paper demonstrate that TRAC/PF1/MOD3 coupled with proper modeling is capable of simulating thermal-hydraulic phenomena typical of that encountered in Mark-22 fuel assembly during LOCA/ECS conditions.

Fischer, S.R.; McDaniel, C.K.

1992-01-01T23:59:59.000Z

240

Experimental analysis of control loops with different delay times in the supply air system of a radiator test rig  

Science Journals Connector (OSTI)

The test rig of low-temperature hot-water radiator is a typical multi-input multi-output (MIMO) thermal system with large time delay. Aiming at the control of the supply air temperature and the temperature of the environmental chamber in the test rig, the paper carries out the fuzzy control experiments and PI control experiments based on adjusting the electric heater in the supply air system, in which there are two control loops with various delay time. The experiments researched two types of fuzzy control methods which are the basic fuzzy control (BFC), and the self-organizing rules fuzzy control (SORFC) with zero initial control rules. For the control loop of supply air temperature with short delay time, PI control performs better with fast convergence speed and small overshoot than the BFC and the SORFC. The convergence speed of the BFC method is lower than other two control methods. For the control loop of chamber temperature with long delay time, the SORFC has a satisfied control performance with less overshoot and stable error than the BFC and PI control.

Yongpan Chen; Jili Zhang; Zhen Lu; Tianyi Zhao; Hui Liu

2011-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "indicators rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Small (5 million Btu/h) and large (300 million Btu/h) thermal test rigs for coal and coal slurry burner development  

SciTech Connect

NEI International Combustion Ltd. of Derby, England, now operates two thermal test rigs for the development of burners capable of handling coal-water slurries (CWS). A general description of the large rig and its capacity was given. Also, the necessary conversions of the equipment to handle CWS were described. Information on the properties of the CWS was included. This consisted of chemical analysis of the parent coal and the slurry, sieve analysis of a dry sample, and viscosity versus temperature data of the CWS. The process of design development of the burner was outlined. Ten illustrations were presented, including schematic diagrams of equipment and graphs of data.

Allen, J.W.; Beal, P.R.; Hufton, P.F.

1983-01-01T23:59:59.000Z

242

An estimation of the penetration rate of rotary drills using the Specific Rock Mass Drillability index  

Science Journals Connector (OSTI)

The main purpose of the present study was to provide a practical, convenient drillability prediction model based on rock mass characteristics, geological sampling from blast holes, and drill operational factors. Empirical equations that predict drill penetration rate have been developed using statistical analyses of data from the Sarcheshmeh Copper Mine. Seven parameters of the rock or rock mass, including uniaxial compressive strength (UCS) of the rock, Schmidt hammer hardness value, quartz content, fragment size (d80), alteration, and joint dip, are included in the model along with two operational parameters of the rotary drill, bit rotational speed and thrust. These parameters were used to predict values of the newly developed Specific Rock Mass Drillability (SRMD) index. Comparing measured SRMD values to those predicted by the multi-parameter linear, or nonlinear, regression models showed good agreement. The correlation coefficients were 0.82 and 0.81, respectively.

Alireza Cheniany; Khoshrou Seyed Hasan; Kourosh Shahriar; Jafar Khademi Hamidi

2012-01-01T23:59:59.000Z

243

Heat transfer and combustion characteristics of a burner with a rotary regenerative heat exchanger  

SciTech Connect

The authors have developed a Rotary Regenerative Combustion (RRX) System, which is coupled with a compact high efficiency regenerative air heat exchanger and a combustion burner. This system contributes to saving energy of fuel firing industrial furnaces and decreases NO{sub x} emission. This technology can be considered as a solution of greenhouse problem. This paper, discusses a compact high efficiency regenerative air heat exchanger in comparison with the existing types of regenerative burners and reverse firing with high momentum fuel jet (with motive fluid) in the furnace. This burner is compact in size, with high fuel efficiency, low NOx emission, easy to operate, and reliable, based on the results of field tests and commercial operations. The authors can say that the RRX system is a regenerative burner of the second generation.

Hirose, Yasuo; Kaji, Hitoshi; Arai, Norio

1998-07-01T23:59:59.000Z

244

Method and apparatus for maximizing throughput of indirectly heated rotary kilns  

DOE Patents (OSTI)

An apparatus and method for achieving improved throughput capacity of indirectly heated rotary kilns used to produce pyrolysis products such as shale oils or coal oils that are susceptible to decomposition by high kiln wall temperatures is disclosed. High throughput is achieved by firing the kiln such that optimum wall temperatures are maintained beginning at the point where the materials enter the heating section of the kiln and extending to the point where the materials leave the heated section. Multiple high velocity burners are arranged such that combustion products directly impact on the area of the kiln wall covered internally by the solid material being heated. Firing rates for the burners are controlled to maintain optimum wall temperatures.

Coates, Ralph L; Smoot, L. Douglas; Hatfield, Kent E

2012-10-30T23:59:59.000Z

245

Testing to expand the rotary mode core sampling system operating envelope  

SciTech Connect

Rotary sampling using the Rotary Mode Core Sampling System (RMCSS) is constrained by what is referred to as the ``Operating Envelope``. The Operating Envelop defines the maximum downward force, maximum rotational speed and minimum purge gas flow allowed during operation of the RMCSS. The original values of 1170 lb. down force, 55 RPM rotational speed, and 30 SCFM nitrogen purge gas were determined during original envelope testing. This envelope was determined by observing the temperature rise on the bitface while drilling into waste simulants. The maximum temperature in single-shell tanks (SSTS) is considered to be approximately 9O C and the critical drill bit temperature, which is the temperature at which an exothermic reaction could be initiated in the tank waste, was previously determined to be 150 C. Thus, the drill bit temperature increase was limited to 60 C. Thermal properties of these simulants approximated typical properties of waste tank saltcake. Later, more detailed envelope testing which used a pumice block simulant, showed a notably higher temperature rise while drilling. This pumice material, which simulated a ``worst case`` foreign object embedded in the waste, has lower thermal conductivity and lower thermal diffusivity than earlier simulants. These properties caused a slower heat transfer in the pumice than in the previous simulants and consequently a higher temperature rise. The maximum downward force was subsequently reduced to 750 lb (at a maximum 55 RPM and minimum 30 SCFM purge gas flow) which was the maximum value at which the drill bit could be operated and still remain below the 60 C temperature rise.

Witwer, K.S.

1998-01-21T23:59:59.000Z

246

TESTING AND EVALUATION OF THE MODIFIED DESIGN OF THE 25-DISK ROTARY MICROFILTER  

SciTech Connect

This report details redesign of a commercially available rotary microfilter to meet the operational and maintenance requirements for radioactive service. Personnel developed the design and coordinated procurement of two filters followed by testing of one unit. System testing examined the ability to rinse soluble material from the system, filtration performance using several insoluble solids loadings, effectiveness in washing sludge, amount of wear to parts and maintenance of the system including the insertion and removal of the filter stack, and the ability to flush solids from the system. The test program examined flushing the filter for soluble material by filling the system with a Rhodamine WT dye solution. Results showed that draining the system and rinsing with 50 gallons of water resulted in grater than 100X reduction of the dye concentration. Personnel determined filter performance using various amounts of insoluble sludge solids ranging from 0.06 to 15 weight percent (wt%) insoluble solids in a 3 molar (M) sodium simulated supernate. Through approximately 120 hours of start-and-stop (i.e., day shift) operation and various insoluble solids loadings, the filter produced filtration rates between 3 and 7 gallons per minute (gpm) (0.12-0.29 gpm/ft{sup 2}) for a 25-disk filter. Personnel washed approximately 80 gallons of simulated sludge using 207 gallons of inhibited water. Washing occurred at constant volume with wash water fed to a well mixed tank at the same rate as filtrate removal. Performance measurement involved collecting and analyzing samples throughout the washing for density and sodium content. Results showed an effective washing, mimicking a predicted dilution calculation for a well mixed tank and reducing the sodium concentration from 3.2 M to less than 0.3 M. Filtration rates during the washing process ranged between 3 and 4.3 gpm for one filter unit. The filter system then concentrated the washed 15 wt% insoluble solids slurry to approximately 20 wt% insoluble solids with no operational problems with the exception of the entrainment of air due to leaking packing in the feed pump. Prior to the air entrainment, the filtration rate was approximately 4.2 gpm for one filter assembly with the process fluid temperature adjusted to 35 C. Personnel measured the turbidity of filtrate samples from all phases of testing. All samples measured were less than 3 NTU, with the majority of samples less than 1 NTU. Thus, all measurements fell below the process acceptance criterion of less than 5 NTU. After slurry operations, personnel rinsed the filter with the equivalent of 250 gallons of water by re-circulating 50 gallons of water. The residual sludge solids remaining on the filter stack weighed approximately 685 grams. This amount of solids corresponds to an equivalent activity of 15.1 curies (Ci) beta and 0.38 Ci gamma radiation dose for Sludge Batch 4. Workers completely disassembled the filter system and examined it for signs of wear and component operation. An evaluation by a John Crane Inc. representative concluded that the wear observed on the mechanical seal resulted primarily from the numerous stops and starts, the abrasive nature of the process fluid and the possibility that the seal faces did not receive enough lubrication from the process fluid. No measurable slurry bypassed the mechanical seal. While it is extremely difficult to predict the life of the seal, the vendor representative indicates a minimum of one year in present service is reasonable. Changing the seal face material from silicon-carbide to a graphite-impregnated silicon-carbide is expected to double the life of the seal. Replacement with an air seal might be expected to increase lifetime to five years. The bottom bushing showed wear due to a misalignment during the manufacture of the filter tank. Minor adjustments to the alignment with shims and replacement of the graphite bushing with a superior material will greatly reduce this wear pattern.

Herman, D; Michael Poirier, M; Samuel Fink, S

2006-09-29T23:59:59.000Z

247

American Institute of Aeronautics and Astronautics, Infotech@Aerospace Conference, Paper No. 2005-7077 A Small Semi-Autonomous Rotary-Wing Unmanned Air  

E-Print Network (OSTI)

-7077 1 A Small Semi-Autonomous Rotary-Wing Unmanned Air Vehicle (UAV) Scott D. Hanford* , Lyle N. Long such as the Fire Scout and Hummingbird currently have the capability to fly autonomously, land in a specific

248

Type A Accident Investigation of the June 21, 2001, Drilling Rig Operator Injury at the Fermi National Accelerator Laboratory, August 2001  

Energy.gov (U.S. Department of Energy (DOE))

On June 21, 2001, at approximately 9:40 A.M., a construction sub-tier contractor employee (the “Operator”) at the Fermi National Accelerator Laboratory (Fermilab) received serious head injuries requiring hospitalization when he was struck by part of the drilling rig (a “tong”) that he was operating.

249

A Hardware-in-the-Loop Test Rig for Designing Near-Earth Aerial Robotics Vefa Narli and Paul Y. Oh  

E-Print Network (OSTI)

and build- ings. The lack of flight data and performance metrics poses a gap that prevents the analytical is a full-scale diorama of a near-Earth environment like forests. The rig is used to capture metrics adverse weather conditions and obscurants, like fog, rain or dust. A key gap in the knowledge domain

Oh, Paul

250

High vacuum indirectly-heated rotary kiln for the removal and recovery of mercury from air pollution control scrubber waste  

SciTech Connect

SepraDyne corporation (Denton, TX, US) has conducted pilot-scale treatability studies of dewatered acid plant blowdown sludge generated by a copper smelter using its recently patented high temperature and high vacuum indirectly-heated rotary retort technology. This unique rotary kiln is capable of operating at internal temperatures up to 850 C with an internal pressure of 50 torr and eliminates the use of sweep gas to transport volatile substances out of the retort. By removing non-condensables such as oxygen and nitrogen at relatively low temperatures and coupling the process with a temperature ramp-up program and low temperature condensation, virtually all of the retort off-gases produced during processing can be condensed for recovery. The combination of rotation, heat and vacuum produce the ideal environment for the rapid volatilization of virtually all organic compounds, water and low-to-moderate boiling point metals such as arsenic, cadmium and mercury.

Hawk, G.G.; Aulbaugh, R.A. [Scientific Consulting Labs., Inc., Farmers Branch, TX (United States)] [Scientific Consulting Labs., Inc., Farmers Branch, TX (United States)

1998-12-31T23:59:59.000Z

251

System design specification for rotary mode core sample trucks No. 2, 3, and 4 programmable logic controller  

SciTech Connect

The system this document describes controls several functions of the Core Sample Truck(s) used to obtain nuclear waste samples from various underground storage tanks at Hanford. The system will monitor the sampling process and provide alarms and other feedback to insure the sampling process is performed within the prescribed operating envelope. The intended audience for this document is anyone associated with rotary or push mode core sampling. This document describes the Alarm and Control logic installed on Rotary Mode Core Sample Trucks (RMCST) {number_sign}2, 3, and 4. It is intended to define the particular requirements of the RMCST alarm and control operation (not defined elsewhere) sufficiently for detailed design to implement on a Programmable Logic Controller (PLC).

Dowell, J.L.; Akers, J.C.

1995-12-31T23:59:59.000Z

252

Application of Membranes to Treatment of Water Based Exploration and Production Wastes  

E-Print Network (OSTI)

Page 1. 1 Schematic of a rotary drilling rig??????????????????????????????. 4 1. 2 Subsurface reach and rig sizes in the last thirty years?????????????????? 5 1. 3 Waste disposal statistics??????????????????????????????????.. 12 1... equipment and rotary system equipment. A drilling rig is a machine used to drill the wellbore [2], it usually entails every equipment in the drilling process apart from the living quarters. Onshore drilling rig types includes the conventional rig...

Olatubi, Oluwaseun Alfred

2010-10-12T23:59:59.000Z

253

Surface Hopping Excited-State Dynamics Study of the Photoisomerization of a Light-Driven Fluorene Molecular Rotary Motor  

Science Journals Connector (OSTI)

Surface Hopping Excited-State Dynamics Study of the Photoisomerization of a Light-Driven Fluorene Molecular Rotary Motor ... The potential energy surfaces of the ground electronic state (S0) and the first singlet excited state (S1) are explored by semiempirical quantum-chemical calculations using the orthogonalization-corrected OM2 Hamiltonian in combination with a multireference configuration interaction (MRCI) treatment. ... Photoswitching of simple photochromic molecules attracts substantial attention because of its possible role in future photon-driven molecular electronics. ...

Andranik Kazaryan; Zhenggang Lan; Lars V. Schäfer; Walter Thiel; Michael Filatov

2011-05-24T23:59:59.000Z

254

Energy-conservation indicators  

SciTech Connect

A series of Energy Conservation Indicators were developed for the Department of Energy to assist in the evaluation of current and proposed conservation strategies. As descriptive statistics that signify current conditions and trends related to efficiency of energy use, indicators provide a way of measuring, monitoring, or inferring actual responses by consumers in markets for energy services. Related sets of indicators are presented in some 30 one-page indicator summaries. Indicators are shown graphically, followed by several paragraphs that explain their derivation and highlight key findings. Indicators are classified according to broad end-use sectors: Aggregate (economy), Residential, Commercial, Industrial, and transportation. In most cases annual time series information is presented covering the period 1960 through 1981.

Belzer, D.B.

1982-06-01T23:59:59.000Z

255

Report on Testing to Expand the Rotary Mode Core Sampling Operating Envelope  

SciTech Connect

The Tank Waste Remediation System (TWRS) Characterization Equipment Group requested that the Numatec Hanford Corporation--Engineering Testing Laboratory (ETL) perform Rotary Mode Core Sampling (RMCS) Operating Envelope (OE) testing. This testing was based upon Witwer 1998a and was performed at different time periods between May and September 1998. The purpose of this testing was to raise the maximum down force limit for rotary mode core sampling as outlined in the current OE. If testing could show that a higher down force could be used while drilling into a concrete/pumice block simulant while still remaining below the 60 C limitation, then the current OE could be revised to include the new, higher, down force limit. Although the Test Plan discussed varying the purge flow rate and rotation rate to find ''optimal'' drilling conditions, the number of drill bits that could be destructively tested was limited. Testing was subsequently limited in scope such that only the down force would be varied while the purge flow rate and rotation rate were kept constant at 30 scfm and 55 rpm respectively. A second objective, which was not part of the original test plan, was added prior to testing. The Bit Improvement testing, mentioned previously, revealed that the drill bits tested in the OE testing were made of a slightly different metal matrix than the ones currently used. The older bits, a Longyear part number 100IVD/5 (/5 bit), had tungsten carbide mixed into the metal matrix that forms the cutting teeth. The currently used bits, Longyear part number 100IVD/8 (/8 bit), instead have tungsten metal in the matrix and no tungsten carbide. Rockwell C hardness testing showed that the /5 bit was significantly harder than the /8 bit, with values of /8 vs. 8, respectively. The change from the /5 bit to the /8 bit was made immediately after the previous OE testing in 1996 because of sparking concerns with the tungsten carbide in the /5 bit. This difference in hardness between the two bit materials was discovered in the Bit Improvement Testing and was expected to affect this OE testing. The second objective, therefore, was to quantify what affect this change in material had and define the OE, based on the current /8 bit design rather than the old /5 bit design.

BOGER, R.M.

1999-12-13T23:59:59.000Z

256

Acoustic plug release indicator  

SciTech Connect

The present invention comprises an acoustic plug release indicator system. The acoustic plug release indicatior system comprises a microphone, recording system and operator listening device.

Carter, E.E. Jr.

1984-09-04T23:59:59.000Z

257

Engagement Indicators Wittenberg University  

E-Print Network (OSTI)

Indicators Report Theme Engagement Indicator Higher-Order Learning Reflective and Integrative Learning-and-whisker charts show the variation in scores within your institution and comparison groups. Straightforward in magnitude (before rounding) are highlighted in the Overview. EIs vary more among students within

Bogaerts, Steven

258

Method and system including a double rotary kiln pyrolysis or gasification of waste material  

DOE Patents (OSTI)

A method of destructively distilling an organic material in particulate form wherein the particulates are introduced through an inlet into one end of an inner rotating kiln ganged to and coaxial with an outer rotating kiln. The inner and outer kilns define a cylindrical annular space with the inlet being positioned in registry with the axis of rotation of the ganged kilns. During operation, the temperature of the wall of the inner rotary kiln at the inlet is not less than about 500.degree. C. to heat the particulate material to a temperature in the range of from about 200.degree. C. to about 900.degree. C. in a pyrolyzing atmosphere to reduce the particulate material as it moves from the one end toward the other end. The reduced particulates including char are transferred to the annular space between the inner and the outer rotating kilns near the other end of the inner rotating kiln and moved longitudinally in the annular space from near the other end toward the one end in the presence of oxygen to combust the char at an elevated temperature to produce a waste material including ash. Also, heat is provided which is transferred to the inner kiln. The waste material including ash leaves the outer rotating kiln near the one end and the pyrolysis vapor leaves through the particulate material inlet.

McIntosh, Michael J. (Bolingbrook, IL); Arzoumanidis, Gregory G. (Naperville, IL)

1997-01-01T23:59:59.000Z

259

A method and system including a double rotary kiln pyrolysis or gasification of waste material  

SciTech Connect

A method is described for destructively distilling an organic material in particulate form wherein the particulates are introduced through an inlet into one end of an inner rotating kiln ganged to and coaxial with an outer rotating kiln. The inner and outer kilns define a cylindrical annular space with the inlet being positioned in registry with the axis of rotation of the ganged kilns. During operation, the temperature of the wall of the inner rotary kiln at the inlet is not less than about 500 C to heat the particulate material to a temperature in the range of from about 200 C to about 900 C in a pyrolyzing atmosphere to reduce the particulate material as it moves from the one end toward the other end. The reduced particulates including char are transferred to the annular space between the inner and the outer rotating kilns near the other end of the inner rotating kiln and moved longitudinally in the annular space from near the other end toward the one end in the presence of oxygen to combust the char at an elevated temperature to produce a waste material including ash. Also, heat is provided which is transferred to the inner kiln. The waste material including ash leaves the outer rotating kiln near the one end and the pyrolysis vapor leaves through the particulate material inlet.

McIntosh, M.J.; Arzoumanidis, G.G.

1995-12-31T23:59:59.000Z

260

Method and system including a double rotary kiln pyrolysis or gasification of waste material  

DOE Patents (OSTI)

A method is described for destructively distilling an organic material in particulate form wherein the particulates are introduced through an inlet into one end of an inner rotating kiln ganged to and coaxial with an outer rotating kiln. The inner and outer kilns define a cylindrical annular space with the inlet being positioned in registry with the axis of rotation of the ganged kilns. During operation, the temperature of the wall of the inner rotary kiln at the inlet is not less than about 500 C to heat the particulate material to a temperature in the range of from about 200 C to about 900 C in a pyrolyzing atmosphere to reduce the particulate material as it moves from the one end toward the other end. The reduced particulates including char are transferred to the annular space between the inner and the outer rotating kilns near the other end of the inner rotating kiln and moved longitudinally in the annular space from near the other end toward the one end in the presence of oxygen to combust the char at an elevated temperature to produce a waste material including ash. Also, heat is provided which is transferred to the inner kiln. The waste material including ash leaves the outer rotating kiln near the one end and the pyrolysis vapor leaves through the particulate material inlet. 5 figs.

McIntosh, M.J.; Arzoumanidis, G.G.

1997-09-02T23:59:59.000Z

Note: This page contains sample records for the topic "indicators rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Prognostics and health management design for rotary machinery systems—Reviews, methodology and applications  

Science Journals Connector (OSTI)

Abstract Much research has been conducted in prognostics and health management (PHM), an emerging field in mechanical engineering that is gaining interest from both academia and industry. Most of these efforts have been in the area of machinery PHM, resulting in the development of many algorithms for this particular application. The majority of these algorithms concentrate on applications involving common rotary machinery components, such as bearings and gears. Knowledge of this prior work is a necessity for any future research efforts to be conducted; however, there has not been a comprehensive overview that details previous and on-going efforts in PHM. In addition, a systematic method for developing and deploying a PHM system has yet to be established. Such a method would enable rapid customization and integration of PHM systems for diverse applications. To address these gaps, this paper provides a comprehensive review of the PHM field, followed by an introduction of a systematic PHM design methodology, 5S methodology, for converting data to prognostics information. This methodology includes procedures for identifying critical components, as well as tools for selecting the most appropriate algorithms for specific applications. Visualization tools are presented for displaying prognostics information in an appropriate fashion for quick and accurate decision making. Industrial case studies are included in this paper to show how this methodology can help in the design of an effective PHM system.

Jay Lee; Fangji Wu; Wenyu Zhao; Masoud Ghaffari; Linxia Liao; David Siegel

2014-01-01T23:59:59.000Z

262

Apparatus and methods for cooling and sealing rotary helical screw compressors  

DOE Patents (OSTI)

In a compression system which incorporates a rotary helical screw compressor, and for any type of gas or refrigerant, the working liquid oil is atomized through nozzles suspended in, and parallel to, the suction gas flow, or alternatively the nozzles are mounted on the suction piping. In either case, the aim is to create positively a homogeneous mixture of oil droplets to maximize the effectiveness of the working liquid oil in improving the isothermal and volumetric efficiencies. The oil stream to be atomized may first be degassed at compressor discharge pressure by heating within a pressure vessel and recovering the energy added by using the outgoing oil stream to heat the incoming oil stream. The stripped gas is typically returned to the compressor discharge flow. In the preferred case, the compressor rotors both contain a hollow cavity through which working liquid oil is injected into channels along the edges of the rotors, thereby forming a continuous and positive seal between the rotor edges and the compressor casing. In the alternative method, working liquid oil is injected either in the same direction as the rotor rotation or counter to rotor rotation through channels in the compressor casing which are tangential to the rotor edges and parallel to the rotor center lines or alternatively the channel paths coincide with the helical path of the rotor edges. 14 figs.

Fresco, A.N.

1997-08-05T23:59:59.000Z

263

Apparatus and methods for cooling and sealing rotary helical screw compressors  

DOE Patents (OSTI)

In a compression system which incorporates a rotary helical screw compressor, and for any type of gas or refrigerant, the working liquid oil is atomized through nozzles suspended in, and parallel to, the suction gas flow, or alternatively the nozzles are mounted on the suction piping. In either case, the aim is to create positively a homogeneous mixture of oil droplets to maximize the effectiveness of the working liquid oil in improving the isothermal and volumetric efficiencies. The oil stream to be atomized may first be degassed at compressor discharge pressure by heating within a pressure vessel and recovering the energy added by using the outgoing oil stream to heat the incoming oil stream. The stripped gas is typically returned to the compressor discharge flow. In the preferred case, the compressor rotors both contain a hollow cavity through which working liquid oil is injected into channels along the edges of the rotors, thereby forming a continuous and positive seal between the rotor edges and the compressor casing. In the alternative method, working liquid oil is injected either in the same direction as the rotor rotation or counter to rotor rotation through channels in the compressor casing which are tangential to the rotor edges and parallel to the rotor centerlines or alternatively the channel paths coincide with the helical path of the rotor edges.

Fresco, Anthony N. (P.O. Box 734, Upton, NY 11973)

1997-01-01T23:59:59.000Z

264

Plant indicators in Iraq  

Science Journals Connector (OSTI)

Native plants of Iraq have shown considerable variation in their ability...Seidlitzia rosmarinus andHalocnemum strobilaceum indicate very high soil sodium contents, and others high magnesium and sulphate contents...

T. A. Al-Ani; I. M. Habib; A. I. Abdulaziz; N. A. Ouda

1971-08-01T23:59:59.000Z

265

155The Great Gulf Oil Catastrophe of 2010 NASA's Terra satellite flew over the Deepwater Horizon rig's oil spill in the Gulf  

E-Print Network (OSTI)

rig's oil spill in the Gulf of Mexico on Saturday, May 1 and captured the above natural-color image of Mexico. NOAA's estimated release rate of oil spilling into the Gulf is 200,000 gallons per day since/meter 2 ? B) kg/meter 2 ? Problem 4 ­ The density of crude oil is about D=850 kg/m 3 . From your estimate

266

General Indicators: Change from  

E-Print Network (OSTI)

Completed in 1 business day 81% -1% 100% - 78% 100% 80% Quality Inspections Completed 95% - - - - Utilities: See Definitions Document for descriptions of performance measures and specific color code target values. Trend status color indicators ­ identifies changes from the prior month: Steam/Chilled Water

Webb, Peter

267

Indicators: Performance Statistics  

E-Print Network (OSTI)

-82 100 10 7 8 0 10 Completed in 1 business day 74% -14% 100% 60% 71% 63% 100% 100% Quality of performance measures and specific color code target values. Trend status color indicators ­ identifies changes Breakdown All Zones Combined Zone Breakdown Steam/Chilled Water Electric 17% 20% 0 100% 100% 1 Improvement

Webb, Peter

268

Indicators: Performance Statistics  

E-Print Network (OSTI)

% Quality Inspections Completed 66% +12% 95% 86% 95% 52% 81% 51% 76% Utilities: Performance Statistics of performance measures and specific color code target values. Trend status color indicators ­ identifies changes from the prior month: Key: - 54% Electric - 0% All Zones Combined Zone Breakdown Steam/Chilled Water 0

Webb, Peter

269

General Indicators: Change from  

E-Print Network (OSTI)

100 4 11 2 75 Completed in 1 business day 92% -5% 100% 100% 100% 100% 91% Quality Inspections measures and specific color code target values. Trend status color indicators ­ identifies changes from the prior month: 100% 50% 70% - All Districts Combined 0 Electric 0 District Breakdown Steam/Chilled Water

Webb, Peter

270

General Indicators: Change from  

E-Print Network (OSTI)

100 0 5 3 84 Completed in 1 business day 97% +16% 100% - 100% 100% 96% Quality Inspections Completed-FLS 86% -7% 70% Key: See Definitions Document for descriptions of performance measures and specific color code target values. Trend status color indicators ­ identifies changes from the prior month: Steam

Webb, Peter

271

Indicators: Performance Statistics  

E-Print Network (OSTI)

% 75% 100% 80% 100% 93% Quality Inspections Completed 54% +2% 95% 40% 34% 57% 88% 60% 54% Utilities for descriptions of performance measures and specific color code target values. Trend status color indicators ­ identifies changes from the prior month: Key: 0% 43% Electric 0% 11% All Zones Combined Zone Breakdown Steam

Webb, Peter

272

Indicators: Performance Statistics  

E-Print Network (OSTI)

's): Quantity 117 -97 100 13 14 9 4 77 Completed in 1 business day 88% -8% 100% 77% 43% 78% 100% 99% Quality measures and specific color code target values. Trend status color indicators ­ identifies changes from the prior month: Steam 100% 58% 0 - Electric 26% 0 UNIVERSITY SERVICES ­ FACILITIES MANAGEMENT MONTHLY

Webb, Peter

273

Indicators: Change from  

E-Print Network (OSTI)

% 69% 100% 98% Quality Inspections Completed 52% +21% 95% 25% 100% 82% 0% Utilities: Performance for descriptions of performance measures and specific color code target values. Trend status color indicators OPERATIONS SCORECARD All Districts Combined District Breakdown Steam/Chilled Water February 2008 All

Webb, Peter

274

General Indicators: Change from  

E-Print Network (OSTI)

100 8 14 5 119 Completed in 1 business day 97% +17% 100% 88% 93% 100% 98% Quality Inspections measures and specific color code target values. Trend status color indicators ­ identifies changes from the prior month: All Districts Combined 0 Electric 2 District Breakdown Steam/Chilled Water - 55% 39

Webb, Peter

275

General Indicators: Change from  

E-Print Network (OSTI)

's): Quantity 10 No Change 100 1 1 3 5 Completed in 1 business day 70% -10% 100% 100% 0% 100% 60% Quality measures and specific color code target values. Trend status color indicators ­ identifies changes from the prior month: Steam/Chilled Water Electric 84% 84% 4 3 - - Met Target Requires ReviewMissed Target

Webb, Peter

276

Indicators: Change from  

E-Print Network (OSTI)

% Quality Inspections Completed 99% No Change 95% 100% 100% 99% 100% Utilities: Performance Statistics of performance measures and specific color code target values. Trend status color indicators ­ identifies changes SCORECARD All Districts Combined District Breakdown Steam/Chilled Water June 2008 All Districts Combined All

Webb, Peter

277

Indicators: Change from  

E-Print Network (OSTI)

's): Quantity 207 -39 100 16 24 5 5 157 Completed in 1 business day 84% -9% 100% 88% 100% 80% 100% 81% Quality measures and specific color code target values. Trend status color indicators ­ identifies changes from the prior month: Key: 50% 52% Electric - 26% All Zones Combined Zone Breakdown Steam/Chilled Water 3 0 All

Webb, Peter

278

Indicators: Change from  

E-Print Network (OSTI)

% Quality Inspections Completed 99% +3% 95% 100% 98% 99% 100% Utilities: Performance Statistics Current of performance measures and specific color code target values. Trend status color indicators ­ identifies changes Combined District Breakdown Steam/Chilled Water May 2008 All Districts Combined All Districts Combined

Webb, Peter

279

Indicators: Change from  

E-Print Network (OSTI)

% 100% 88% Quality Inspections Completed 26% -17% 95% 43% 72% 0% 61% 10% 63% Utilities: Performance for descriptions of performance measures and specific color code target values. Trend status color indicators which may understate actual compliance results. All Zones Combined Zone Breakdown Steam/Chilled Water 0

Webb, Peter

280

Triboluminescent indicator system  

DOE Patents (OSTI)

There is provided a light emitting device comprising a plurality of triboluminescent particles dispersed throughout a low density, frangible body and activated by rapidly crushing the body in order to transfer mechanical energy to some portion of the particles. The light emitted by these mechanically excited particles is collected and directed into a light conduit and transmitted to a detector/indicator means.

Goods, Steven H. (Livermore, CA); Dentinger, Paul M. (Sunol, CA); Whinnery, Jr., Leroy L. (Danville, CA)

2003-06-24T23:59:59.000Z

Note: This page contains sample records for the topic "indicators rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

EVALUATION OF SUPPLEMENTAL PRE-TREATMENT DEVELOPMENT REQUIREMENTS TO MEET TRL 6 ROTARY MICROFILTRATION  

SciTech Connect

In spring 2011, the Technology Maturation Plan (TMP) for the Supplemental Treatment Project (RPP-PLAN-49827, Rev. 0), Technology Maturation Plan for the Treatment Project (T4S01) was developed. This plan contains all identified actions required to reach technical maturity for a field-deployable waste feed pretreatment system. The supplemental pretreatment system has a filtration and a Cs-removal component. Subsequent to issuance of the TMP, rotary microfiltration (RMF) has been identified as the prime filtration technology for this application. The prime Cs-removal technology is small column ion exchange (ScIX) using spherical resorcinol formaldehyde (sRF) as the exchange resin. During fiscal year 2011 (FY2011) some of the tasks identified in the TMP have been completed. As of September 2011, the conceptual design package has been submitted to DOE as part of the critical decision (CD-1) process. This document describes the remaining tasks identified in the TMP to reach technical maturity and evaluates the validity of the proposed tests to fill the gaps as previously identified in the TMP. The potential vulnerabilities are presented and the completed list of criteria for the DOE guide DOE G 413.3-4 different technology readiness levels are added in an attachment. This evaluation has been conducted from a technology development perspective - all programmatic and manufacturing aspects were excluded from this exercise. Compliance with the DOE G 413.3-4 programmatic and manufacturing requirements will be addressed directly by the Treatment Project during the course of engineering design. The results of this evaluation show that completion of the proposed development tasks in the TMP are sufficient to reach TRL 6 from a technological point of view. The tasks involve actual waste tests using the current baseline configuration (2nd generation disks, 40 psi differential pressure, 30 C feed temperature) and three different simulants - the PEP, an AP-Farm and an S-saltcake. Based on FY2011 dollars used in the TMP, these tests will have ROM costs of $950K and require up to 10 months to complete. Completion of the simulant testing will satisfy the TRL 5 and TRL 6 criteria that are related to system testing with materials that represent the full range of properties in a relevant environment.

HUBER HJ

2011-10-03T23:59:59.000Z

282

DOI-BLM-NV-WO10-2014-0002-CX | Open Energy Information  

Open Energy Info (EERE)

rotary drill rig. A track-mounted off-road crawler equipped with water and fuel tanks would also track out to each drill site to supply the drill rig. Water needed for...

283

U.S. Energy Information Administration (EIA)  

Annual Energy Outlook 2012 (EIA)

levels 22.2% below year-ago levels and 25.5% below the 5-year average. The Baker Hughes rotary rig count increased by 1 to 1,875 active units this week. Natural gas rigs remained...

284

U.S. Energy Information Administration (EIA)  

NLE Websites -- All DOE Office Websites (Extended Search)

26, unchanged from the previous week. The oil rig count increased by 6 units to 1,401 rotary rigs. The weekly average natural gas plant liquids composite price (covering July...

285

Natural Gas Weekly Update, Printer-Friendly Version  

Gasoline and Diesel Fuel Update (EIA)

of about 40 percent from the beginning of the year, when a level of 1,267 natural gas rotary rigs were reported on January 2. The decline in natural gas rigs has occurred in...

286

Microsoft Word - Alcoa Extension EBT ROD Attachments - 2010-10...  

NLE Websites -- All DOE Office Websites (Extended Search)

Administration, August 30, 2010 Figure 2 - Natural Gas Rig Count U.S. Natural Gas Rotary Rigs in Operation (Count) 0 200 400 600 800 1000 1200 1400 1600 1800 A u g - 0 6 O...

287

U.S. Energy Information Administration (EIA)  

NLE Websites -- All DOE Office Websites (Extended Search)

levels 22.5% below year-ago levels and 16.6% below the 5-year average. The natural gas rotary rig count totaled 356 as of January 24, which represents a decline of 9 rigs from...

288

Natural Gas Weekly Update, Printer-Friendly Version  

Gasoline and Diesel Fuel Update (EIA)

of the United States total rigs running as of the week ended October 22. Natural gas rotary rigs reached an all-time high of 1,082 during the week ended September 3, 2004,...

289

U.S. Energy Information Administration (EIA)  

Annual Energy Outlook 2012 (EIA)

to data from Baker Hughes Inc., an increase of 6 from the previous week. The natural gas rotary rig count totaled 318, which represents a decrease of 8 rigs from the previous week...

290

U.S. Energy Information Administration (EIA)  

Annual Energy Outlook 2012 (EIA)

count was 1,803 as of March 21, according to data from Baker Hughes Inc. The natural gas rotary rig count totaled 326, which represents a decrease of 18 rigs from the previous...

291

U.S. Energy Information Administration (EIA)  

Annual Energy Outlook 2012 (EIA)

below year-ago levels, and 1.2% below the 5-year average. The Baker Hughes natural gas rotary rig count totaled 349 active units as of Friday, June 21, a decline of 4 rigs from...

292

Background  

NLE Websites -- All DOE Office Websites (Extended Search)

Administration, January 14, 2011 Figure 2 - Natural Gas Rig Count U.S. Natural Gas Rotary Rigs in Operation (Count) 0 400 800 1200 1600 2000 J a n - 0 7 M a r - 0 7 M a y -...

293

U.S. Energy Information Administration (EIA)  

NLE Websites -- All DOE Office Websites (Extended Search)

levels 48.9% below year-ago levels and 46.2% below the 5-year average. The natural gas rotary rig count totaled 345 as of March 7. This represents an increase of 10 rigs from...

294

U.S. Energy Information Administration (EIA)  

NLE Websites -- All DOE Office Websites (Extended Search)

count was 1,809 as of March 14, according to data from Baker Hughes Inc. The natural gas rotary rig count totaled 344, which represents a decrease of 1 rig from the previous week...

295

U.S. Energy Information Administration (EIA)  

Annual Energy Outlook 2012 (EIA)

below year-ago levels and 23.5% below the 5-year average for this week. The Baker Hughes rotary rig count decreased by 4 to 1,871 active units this week. Natural gas rigs...

296

EIA Energy Information Administration  

U.S. Energy Information Administration (EIA) Indexed Site

week to end at 28.30 or 4.88 per MMBtu. For the week ended April 27, the Baker Hughes Rotary Rig Count for the number of drilling rigs actively exploring for or developing...

297

U.S. Energy Information Administration (EIA)  

Gasoline and Diesel Fuel Update (EIA)

below year-ago levels and 21.7% below the 5-year average for this week. The Baker Hughes rotary rig count increased by 12 to 1,883 active units this week. Natural gas rigs...

298

U.S. Energy Information Administration (EIA)  

Gasoline and Diesel Fuel Update (EIA)

year-ago levels and 20.3% below the five-year average for this week. The Baker Hughes rotary rig count increased by 6 to 1,889 active units this week. Natural gas rigs...

299

EIA Energy Information Administration  

U.S. Energy Information Administration (EIA) Indexed Site

for higher consumer prices in the upcoming winter. Other Market Trends: The Baker Hughes Rotary Rig Count of the number of drilling rigs actively exploring for or developing oil...

300

24th Benelux Meeting Systems and Control  

E-Print Network (OSTI)

applied on a half-car test rig.30­14.55 Contribution to the control of a rotary cement kiln - A simu- lation . . . . . . . . . . . . . . . . . . . . . . . . . . .

Serdijn, Wouter A.

Note: This page contains sample records for the topic "indicators rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Mapping DNAPL transport contamination in sedimentary and fractured rock aquifers with high resolution borehole seismic imaging Project No. SF11SS13 FY01 Annual Report  

E-Print Network (OSTI)

rig-installed boreholes have been successful at other sedimentary sites, additional boreholes at the Northeast site should be installed with rotary

Geller, J.T.; Majer, E.L.; Peterson, J.E.; Williams, K.H.; Flexser, S.

2001-01-01T23:59:59.000Z

302

International energy indicators  

SciTech Connect

Extensive data are compiled for energy on the international scene and for the US. Data are indicated from the date given and into 1980 as far as available. Data are given for the international scene on: world crude oil production, 1975-to date; Iran: crude oil capacity, production, and shut-in, 1974-to date; Saudi Arabia: crude oil capacity, production, and shut-in, 1974-to date; OPEC (Ex-Iran and Saudi Arabia): capacity, production, and shut-in, 1974-to date; oil stocks: Free World, US, Japan, and Europe (landed), 1973-to date; petroleum consumption by industrial countries, 1973-to date; USSR crude oil production, 1974-to date; Free World and US nuclear generation capacity, 1973-to date. Data are supplied specifically for the US on US gross imports of crude oil and products, 1973-to date; landed cost of Saudi crude in current and 1974 dollars; US trade in bituminous coal, 1973-to date; summary of US merchandise trade, 1976-to date; and energy/GNP ratio.

Bauer, E.K. (ed.)

1981-02-01T23:59:59.000Z

303

EVALUATION OF AP-FARM SIMULANT COMPOSITION FOR ROTARY MICROFILTER TESTING  

SciTech Connect

This document identifies the feed composition of a Hanford AP tank farm simulant for rotary microfiltration testing. The composition is based on an Hanford Tank Waste Operations Simulator (HTWOS) model run in combination with Tank Waste Information Network (TWINS) data and mineralogical studies of actual waste solids. The feed simulant is intended to be used in test runs at SRNL. The simulant will be prepared in two parts: (1) A supernate, composed of water-soluble salts and (2) The undissolved (actually, undissolvable) solids. Test slurries with distinct solids concentrations (e.g., 0.5, 5 and 10 wt%) are then prepared as needed. The base for the composition of supernate and solids is the modeled feed sequence for a deployment scenario of the Supplemental Pretreatment units within AP-farm. These units comprise a filtration part, the RMF, and a Cesium-removal part, a Small Column Ion Exchange. The primary use of this simulant is for filtration testing - however, in case that it is also used for ion-exchange tests, the amount of Cs-137 that would need to be added is available in Table 1 and Attachment 3. A modified model run (MMR-049) of the Hanford Tank Waste Operations Simulator (HTWOS) system plan 6 case 3 was performed to identify the feed sequence. Case 3 assumed supplemental treatment besides the low activity waste (LAW) melter with supplemental pretreatment supporting the pretreatment facility. The MMR did not cap the duration of supplemental pretreatment to 15 months, but rather used it throughout the entire treatment mission as an add-on option to the pretreatment facility at the Waste Treatment and Immobilization Plant (WTP). Tank 241-AP-105 (AP-105) was chosen as the feed tank to the filtration unit. Other parameters included a fixed minimum of 0.5 wt% solids in the feed and a maximum Na-concentration of 5M in the supernate. The solids rejection from the filtration unit was set to 99.99% and the maximum allowed amount of solids within tank AP-105 was set to 10 wt%. A comprehensive description of the run and the full suite of results were issued as SVF-2364-00. The list of individual feed events including the amounts of liquid and solids transferred for the first five years is added as Attachment 2; the chemical composition of the supernate feed comprises Attachment 3. For the simulant composition, only the first five years of proposed feed delivery were taken into account. The main outcome of MMR-049 was that for the first five years, the feed would come mostly from AP-farms. Multiple delivery campaigns to AP-105 are included in this average feed, while minimizing the amount of contributing tanks to the solids in the feed mix.

HUBER HJ

2011-09-19T23:59:59.000Z

304

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

8 8 HOISTS 8-i This chapter provides safety standards for inspecting, testing, and operating hoists not permanently mounted on overhead cranes and implements the requirements of ASME B30.11 ("Monorail Systems and Underhung Cranes"), B30.16["Overhead Hoists (Underhung)"], and B30.21 ("Manually Lever Operated Hoists") (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). 8.1 GENERAL .................................................................................................................................8-1 8.1.1 Operator Training/Qualification ..................................................................................8-4 8.1.2 Marking........................................................................................................................8-4

305

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

7 7 OVERHEAD AND GANTRY CRANES 7-i This chapter specifies operation, inspection, maintenance, and testing requirements for the use of overhead and gantry cranes and implements the requirements of ASME B30.2 ["Overhead and Gantry Cranes (Top- Running Bridge, Single or Multiple Girder, Top-Running Trolley Hoist)"], B30.11 ("Monorail Systems and Underhung Cranes"), and B30.17 ["Overhead and Gantry Cranes (Top-Running Bridge, Single Girder, Underhung Hoist")] (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). 7.1 GENERAL .................................................................................................................................7-1 7.1.1 Operator Training/Qualification

306

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CHAPTER 9 MOBILE CRANES 9-i This chapter specifies operation, inspection, maintenance, and testing requirements for the use of mobile cranes and implements the requirements of ASME B30.5 ("Mobile and Locomotive Cranes") (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). 9.1 GENERAL .................................................................................................................................9-1 9.1.1 Operator Training/Qualification ..................................................................................9-1 9.1.2 Load Limits..................................................................................................................9-1 9.1.3 Load Rating Chart........................................................................................................9-1

307

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 4 LIFTING PERSONNEL 4-i Chapter 4 Lifting Personnel This chapter specifies the design and inspection requirements for personnel lift platforms as well as the operational requirements for such platforms and appurtenant hoisting equipment. It implements the requirements of ASME B30.23, Personnel Lifting Systems (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). 4.1 GENERAL ................................................................................................................................4-1 4.1.1 Personnel Lifting Evaluation .......................................................................................4-1 4.1.2 Designated Leader .......................................................................................................4-1

308

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Change Notice No. 1 DOE-STD-1090-2007 Change Notice No. 1 DOE-STD-1090-2007 December 2007 Chapter 4 Provide ASME attribution at introduction to the Table on Contents and on Figures 4-3,4 and Exhibits 1 & 2 Chapter 7 Provide ASME attribution at introduction to the Table on Contents and on Figures 7-1,2,3,4,5 and Table 7-1 Chapter 8 Provide ASME attribution at introduction to the Table on Contents and on Figures 8-1,2,3,4,5,6,7,8,9 and Table 8-1 Chapter 9 Provide ASME attribution at introduction to the Table on Contents and on Figures 9-1,2,3,4,5,6 and Table 9-2 Chapter 11 Provide ASME attribution at introduction to the Table on Contents and on Figures 11-10,15 and Tables 11-10,11,14,15,16 Chapter 12 Provide ASME attribution at introduction to the Table on Contents and on

309

rig upgrades2.qxp  

NLE Websites -- All DOE Office Websites (Extended Search)

T R A P E D O F E N E R G Y E T A T S D E T I N U S O F A M E R I C A E A s the oil and gas industry continues to drill in more remote areas, at deeper depths, and in more...

310

A new well surveying tool  

E-Print Network (OSTI)

directional well was to tip the entire rig, then block up one side of the rotary table so as to incline the uppermost joint of the drill pipe. The accuracy obtained by this method left much to be desired. The technique of controlled directional drilling... by Surveying Device for S and 19 , N and 41 . 21 3. Comparison of Measured Angles and Angles Indicated by Surveying Device for NE snd 9 , W and 45 . . . . . . . ~ 22 ABSTRNl T Ever since the advent of rotary drilling the petroleum industry has been...

Haghighi, Manuchehr Mehdizabeh

1966-01-01T23:59:59.000Z

311

Engineering task plan for the development, fabrication and installation of rotary mode core sample truck grapple hoist box level wind system  

SciTech Connect

This Engineering Task Plan is to design, generate fabrication drawings, fabricate, test, and install the grapple hoist level wind system for Rotary Mode Core Sample Trucks (RMCST) 3 and 4. Deliverables will include generating fabrication drawings, fabrication of one level wind system, updating fabrication drawings as required, and installation of level wind systems on RMCST 3 or 4. The installation of the level wind systems will be done during a preventive maintenance outage.

BOGER, R.M.

1999-05-12T23:59:59.000Z

312

An Advisory System For Selecting Drilling Technologies and Methods in Tight Gas Reservoirs  

E-Print Network (OSTI)

). 13 Fig. 6? Rotary drilling process (Bourgoyne et al. 1986). Two main systems are currently used to rotate the drill bit. As of 2007, for onshore drilling, 55% of the drilling rigs are equipped with a rotary table and Kelly- bushing while 45... ................................................................................................ 11 2.2.2. Discussion .................................................................................................. 12 2.3 Fit For Purpose Land Rig ................................................................................. 16 2.4 Slim...

Pilisi, Nicolas

2010-01-16T23:59:59.000Z

313

National Climate Assessment: Indicators System  

NLE Websites -- All DOE Office Websites (Extended Search)

Indicators System Print E-mail Indicators System Print E-mail What are the goals for the NCA indicators? The vision for the National Climate Assessment (NCA) is to create a system of indicators that will help inform policy-makers and citizens understand key aspects of our changing climate. Scientific information about physical climate conditions, climate impacts, vulnerabilities, and preparedness will be tracked and compiled. These measures are called indicators. The goals of the Indicators System are to: Provide meaningful, authoritative climate-relevant measures about the status, rates, and trends of key physical, ecological, and societal variables and values Inform decisions on management, research, and education at regional to national scales Identify climate-related conditions and impacts to help develop effective mitigation and adaptation measures

314

In Vitro Comparison in a Manikin Model: Increasing Apical Enlargement with K3 and K3XF Rotary Instruments  

Science Journals Connector (OSTI)

AbstractIntroduction The aim of the study was to compare the K3 and K3XF systems (SybronEndo, Glendora, CA) after 1 and 2 uses by evaluating apical transportation, working length loss, and working time in a manikin model. Methods Mesial canals of 40 extracted first mandibular molars were instrumented. Radiographs taken after instrumentation with #25, #30, #35, and #40 files were superimposed on the preoperative image in both mesiodistal and buccolingual angulations. AutoCAD (Autodesk Inc, San Rafael, CA) was used to measure working length loss and apical transportation at 0, 0.5, and 1 mm from the working length (WL). The working time was measured. Group comparison was analyzed using post hoc Tukey honestly significant difference tests (P < .05). Results No significant differences were found in apical transportation, working length loss between K3 and K3XF systems, or between the number of uses. Significant differences were found when canal enlargement was performed to a #35–40 (P < .05). K3 instrumentation performed significantly faster (29.6 ± 15.4) than with the K3XF system (40.2 ± 17.7) (P < .05). No differences were observed in working time when comparing the number of uses. Conclusions K3 and R-phase K3XF rotary systems shaped curved root canals safely with minimal apical transportation, even up to a 40/04 file.

Juan Gonzalo Olivieri; Eva Stöber; Marc García Font; Jose Antonio González; Pablo Bragado; Miguel Roig; Fernando Duran-Sindreu

2014-01-01T23:59:59.000Z

315

Energy Efficiency Indicators Methodology Booklet  

E-Print Network (OSTI)

Best Practice Indicates technical potential Actual energy efficiencyenergy efficiency over time. Building on past OECD experience and best practices,best practices. Figure 4. Plant Benchmarking Energy Efficiency

Sathaye, Jayant

2010-01-01T23:59:59.000Z

316

Energy Efficiency Indicators Methodology Booklet  

E-Print Network (OSTI)

indicators that track the penetration rate of new standardrates increase the penetration rate of more efficientshare of technology Penetration rate of different technology

Sathaye, Jayant

2010-01-01T23:59:59.000Z

317

Energy Efficiency Indicators Methodology Booklet  

E-Print Network (OSTI)

of energy use. Biomass energy consumption In developingHence large quantity of biomass energy is required to serveas for Indicator 7, biomass energy use, primary energy and

Sathaye, Jayant

2010-01-01T23:59:59.000Z

318

Engagement Indicators CUNY Queens College  

E-Print Network (OSTI)

Indicators Report Theme Engagement Indicator Higher-Order Learning Reflective & Integrative Learning Learning of at least .3 in magnitude (before rounding) are highlighted in the Overview (p. 3). EIs vary more among in a given EI are displayed for your institution and comparison groups. Box-and-whisker charts show

Johnson Jr.,, Ray

319

Enumeration of Juvenile Salmonids in the Okanogan Basin Using Rotary Screw Traps, Performance Period: March 15, 2006 - July 15, 2006.  

SciTech Connect

The Colville Tribes identified the need for collecting baseline census data on the timing and abundance of juvenile salmonids in the Okanogan River basin for the purpose of documenting local fish populations, augmenting existing fishery data and assessing natural production trends of salmonids. This report documents and assesses the pilot year of rotary trap capture of salmonid smolts on the Okanogan River. The project is a component of the Colville Tribes Okanogan Basin Monitoring and Evaluation Program (OBMEP) which began in 2004. Trapping for outmigrating fish began on 14 March 2006 and continued through 11 July 2006. Anadromous forms of Oncorhynchus, including summer steelhead (O. mykiss), Chinook (O. tshawytscha), and sockeye (O. nerka), were targeted for this study; all have verified, natural production in the Okanogan basin. Both 8-ft and 5-ft rotary screw traps were deployed on the Okanogan River from the Highway 20 Bridge and typically fished during evening hours or 24 hours per day, depending upon trap position and discharge conditions. Juvenile Chinook salmon were the most abundant species trapped in 2006 (10,682 fry and 2,024 smolts), followed by sockeye (205 parr and 3,291 smolts) and steelhead (1 fry and 333 smolts). Of the trapped Chinook, all fry were wild origin and all but five of the smolts were hatchery-reared. All trapped sockeye were wild origin and 88% of the steelhead smolts were hatchery-reared. Mark-recapture experiments were conducted using Chinook fry and hatchery-reared steelhead smolts (sockeye were not used in 2006 because the peak of the juvenile migration occurred prior to the onset of the mark-recapture experiments). A total of 930 chinook fry were marked and released across eight separate release dates (numbers of marked Chinook fry released per day ranged from 34 to 290 fish). A total of 11 chinook fry were recaptured for an overall trap efficiency of 1.18%. A total of 710 hatchery-reared steelhead were marked and released across three separate release dates (numbers of steelhead released per day ranged from 100 to 500 fish). A total of 12 steelhead were recaptured for an overall trap efficiency of 1.69%. A pooled Peterson estimator with a Chapman modification was used to produce population estimates for wild Chinook fry and hatchery-reared steelhead based on the results of the mark-recapture experiments. The 2006 populations for Chinook and steelhead were estimated to be 381,554 (95% confidence intervals: 175,731-587,377) and 14,164 (6,999-21,330), respectively. The population estimates were based on the periods in which mark-recapture experiments were initialized through the end of the trapping season (10 May for steelhead and 1 June for Chinook).

Johnson, Peter N.; Rayton, Michael D.

2007-05-01T23:59:59.000Z

320

A 12-MW-scale pilot study of in-duct scrubbing (IDS) using a rotary atomizer  

SciTech Connect

A low-cost, moderate-removal efficiency, flue gas desulfurization (FGD) technology was selected by the US Department of Energy for pilot demonstration in its Acid Rain Precursor Control Technology Initiative. The process, identified as In-Duct Scrubbing (IDS), applies rotary atomizer techniques developed for lime-based spray dryer FGD while utilizing existing flue gas ductwork and particulate collectors. IDS technology is anticipated to result in a dry desulfurization process with a moderate removal efficiency (50% or greater) for high-sulfur coal-fired boilers. The critical elements for successful application are: (1) adequate mixing of sorbent droplets with flue gas for efficient reaction contact, (2) sufficient residence time to produce a non-wetting product, and (3) appropriate ductwork cross-sectional area to prevent deposition of wet reaction products before particle drying is comple. The ductwork in many older plants, previously modified to meet 1970 Clean Air Act requirements for particulate control, usually meet these criteria. A 12 MW-scale IDS pilot plant was constructed at the Muskingum River Plant of the American Electric Power System. The pilot plant, which operates from a slipstrem attached to the air-preheater outlet duct from the Unit 5 boiler at the Muskingum River Plant (which burns about 4% sulfur coal), is equipped with three atomizer stations to test the IDS concept in vertical and horizontal configurations. In addition, the pilot plant is equipped to test the effect of injecting IDS off- product upstream of the atomizer, on SO{sub 2}and NO{sub x} removals.

Samuel, E.A.; Murphy, K.R.; Demian, A.

1989-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "indicators rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Managed Pressure Drilling Candidate Selection  

E-Print Network (OSTI)

. Rodolphe Leschot invented and patented the earliest form of diamond core drills. T. F. Rowland patented an ?offshore rotary drilling rig?. Captain Lucas, with his Spindletop field wells, Earle Halliburton with his cementing service company, inventors... is the ancient water and brine wells drilled from the prehistoric eras to not so modern times. The second stage is the drilling of the earliest oil wells, and development of basic derricks, rigs, and cable tool rigs. The third stage is the development of rotary...

Nauduri, Anantha S.

2010-07-14T23:59:59.000Z

322

Mexico's Energy Reform and the Potential Impact on Texas' Transportation System  

E-Print Network (OSTI)

preparation ­ Heavy bulldozers and dump trucks to build road to serve pad site · Move rotary rig to pad site;Transportation and Well Development · Five-step well development process: ­ Site preparation ­ Rigging up ­ Drilling ­ Hydraulic fracturing ­ Rigging down #12;Transportation and Well Development · Initial site

323

The place of useful learning | www.strath.ac.uk/afrc University of Strathclyde Glasgow G1 1XQ  

E-Print Network (OSTI)

............................................... 6 ACB Loire Super Plastic Forming Rig ­ 720x720 mm..................... 7 ACB Super Plastic Forming Rig-SPF/FCC 2400x2000 mm...........8 Die Wear Rig - Super Plastic Forming-316.............................................16 MJC Rotary Forge ­ RFN 200T.............................................. 17 500 tonne hydraulic sheet

Mottram, Nigel

324

Becker, K., Malone, M.J., et al., 1998 Proceedings of the Ocean Drilling Program, Initial Reports, Vol. 174B  

E-Print Network (OSTI)

(drill-pipe measurement from rig floor, mbrf): 4457.1 Total depth (drill-pipe measurement from rig floor, mbrf): 4526.6 Distance between rig floor and sea level (m): 11.6 Water depth (drill-pipe measurement Program (ODP) Leg 45, and the sediments at the site were not recov- ered well with the rotary core barrel

325

Physics and the Search for Hydrocarbons  

E-Print Network (OSTI)

Integrated Project Management #12;Rig Drill Pipe Drill Bit Drilling Tools Drilling Fluid Drill rig rotates. Drilling Rig Drill Collars #12;Drill String Technology Electromagnetic & Nuclear Direction & Inclination in real time for decisions. Drill bit Rotary Steerable Direction & Inclination of the drill bit

Dai, Pengcheng

326

Developing indicators for European birds  

Science Journals Connector (OSTI)

...resources, which is a central pillar of the Convention on Biological...birds forms one part of a three-pronged approach to delivering indicators for sustainability in Europe based on birds...a historical study over three decades. J. Appl. Ecol...

2005-01-01T23:59:59.000Z

327

Leadership and Leading Indicators Presentation  

NLE Websites -- All DOE Office Websites (Extended Search)

Leadership Leadership and Leading Indicators Peter S. Winokur, Ph.D., Member Defense Nuclear Facilities Safety Board Thanks to Matt Moury and Doug Minnema August 28, 2008 Objectives * A few thoughts about leadership * Actions taken by leaders * Role of leading indicators * Consider the future August 28, 2008 2 3 Safety Culture Safety culture is an organization's values and behaviors - modeled by its leaders and internalized by its members - that serve to make nuclear safety an overriding priority.* - Dating back to SEN-35-91, it's DOE Policy; - It's perishable; - EFCOG/DOE ISMS Safety Culture Task Team. *INPO, Principles for a Strong Nuclear Safety Culture, November 2004. August 28, 2008 4 Leadership & Mission Top 10 Ways To Know You Have A Safety Culture: * #1 is Leadership - the talk and the walk

328

A safety assessment of rotary mode core sampling in flammable gas single shell tanks: Hanford Site, Richland, Washington  

SciTech Connect

This safety assessment (SA) addresses each of the required elements associated with the installation, operation, and removal of a rotary-mode core sampling (RMCS) device in flammable-gas single-shell tanks (SSTs). The RMCS operations are needed in order to retrieve waste samples from SSTs with hard layers of waste for which push-mode sampling is not adequate for sampling. In this SA, potential hazards associated with the proposed action were identified and evaluated systematically. Several potential accident cases that could result in radiological or toxicological gas releases were identified and analyzed and their consequences assessed. Administrative controls, procedures and design changes required to eliminate or reduce the potential of hazards were identified. The accidents were analyzed under nine categories, four of which were burn scenarios. In SSTS, burn accidents result in unacceptable consequences because of a potential dome collapse. The accidents in which an aboveground burn propagates into the dome space were shown to be in the ``beyond extremely unlikely`` frequency category. Given the unknown nature of the gas-release behavior in the SSTS, a number of design changes and administrative controls were implemented to achieve these low frequencies. Likewise, drill string fires and dome space fires were shown to be very low frequency accidents by taking credit for the design changes, controls, and available experimental and analytical data. However, a number of Bureau of Mines (BOM) tests must be completed before some of the burn accidents can be dismissed with high confidence. Under the category of waste fires, the possibility of igniting the entrapped gases and the waste itself were analyzed. Experiments are being conducted at the BOM to demonstrate that the drill bit is not capable of igniting the trapped gas in the waste. Laboratory testing and thermal analysis demonstrated that, under normal operating conditions, the drill bit will not create high enough temperatures to initiate a propagating reaction in the waste. However, system failure that coincides in a waste layer with high organic content and low moisture may initiate an exothermic reaction in the waste. Consequently, a conservative approach based on the current state of the knowledge resulted in limiting the drilling process to a subset of the flammable-gas tanks. Accidents from the chemical reactions and criticality category are shown to result in acceptable risk. A number of accidents are shown to potentially result in containment (tank liner) breach below the waste level. Mitigative features are provided for these accidents. Gas-release events without burn also are analyzed, and radiological and toxicological consequences are shown to be within risk guidelines. Finally, the consequences of potential spills are shown to be within the risk guidelines.

Raymond, R.E.

1996-04-15T23:59:59.000Z

329

Low latency counter event indication  

DOE Patents (OSTI)

A hybrid counter array device for counting events with interrupt indication includes a first counter portion comprising N counter devices, each for counting signals representing event occurrences and providing a first count value representing lower order bits. An overflow bit device associated with each respective counter device is additionally set in response to an overflow condition. The hybrid counter array includes a second counter portion comprising a memory array device having N addressable memory locations in correspondence with the N counter devices, each addressable memory location for storing a second count value representing higher order bits. An operatively coupled control device monitors each associated overflow bit device and initiates incrementing a second count value stored at a corresponding memory location in response to a respective overflow bit being set. The incremented second count value is compared to an interrupt threshold value stored in a threshold register, and, when the second counter value is equal to the interrupt threshold value, a corresponding "interrupt arm" bit is set to enable a fast interrupt indication. On a subsequent roll-over of the lower bits of that counter, the interrupt will be fired.

Gara, Alan G. (Mount Kisco, NY); Salapura, Valentina (Chappaqua, NY)

2010-08-24T23:59:59.000Z

330

Build a Floating Oil Rig  

Energy.gov (U.S. Department of Energy (DOE))

The U.S. Department of the Interior's Minerals Management Service developed this teacher's guide about the many energy resources found in, over, and under the ocean. Includes sections on petroleum,...

331

PROGRAMME GROUP RESEARCH UPDATE: Biodiversity indicators &  

E-Print Network (OSTI)

1 PROGRAMME GROUP RESEARCH UPDATE: Biodiversity indicators & knowledge management programme group Introduction Duncan Ray The programme group Biodiversity Indicators and Knowledge Management (BIKM) was established by the merger of the Biodiversity Indicators & Evaluation Programme and the Decision Support

332

A leading index of drilling activity: Update and improvements  

SciTech Connect

A five-component composite leading index of United States rotary rig drilling activity is updated. The index is presented for 1949 through April 1986 and is shown to consistently lead turning points in drilling activity. Seven new leading indices based on some new components are also presented. A forecast of drilling activity is made for the remainder of 1986 based on the leading index and the current economic condition of the petroleum industry. The methods used to prepare time series and construct indices are reviewed.

Buell, R.S.; Maurer, R.A.

1986-01-01T23:59:59.000Z

333

Proportional structural effects of formative indicators  

E-Print Network (OSTI)

Formative constructs must influence two or more distinct outcome variables for meaningful tests of the formative conceptualization. Because the construct mediates the effects of its indicators, the indicators must have ...

Franke, George R.; Preacher, K. J.; Rigdon, Ed E.

2009-03-15T23:59:59.000Z

334

Hydrogeochemical Indicators for Great Basin Geothemal Resources  

Energy.gov (U.S. Department of Energy (DOE))

Hydrogeochemical Indicators for Great Basin Geothemal Resources presentation at the April 2013 peer review meeting held in Denver, Colorado.

335

Ocean indicators Current knowledge and future directions  

E-Print Network (OSTI)

Ocean indicators Current knowledge and future directions Brian Burke, NOAA Fisheries Brian.Burke@noaa.gov #12;· Review of ocean indicator work · Forecasting · Indicator gaps and the importance of mechanistic understanding · Plugging in to management #12;Haeseker et al. 2012 Ocean survival is low and variable #12;-10 -5

336

Some perspectives on pulse detonation propulsion F.K. Lu and D.R. Wilson  

E-Print Network (OSTI)

chamber, a rotary valve injection system for three gas species (fuel, oxidizer and purge), an electric.62 cm section was used to support the mounting of the arc-plug igniter. A photograph of the test rig

Texas at Arlington, University of

337

Natural Gas Weekly Update, Printer-Friendly Version  

Gasoline and Diesel Fuel Update (EIA)

the report week at 80.30 per barrel, or 13.84 per MMBtu. The number of natural gas rotary rigs rose by 3 to 728, according to data Baker Hughes Incorporated released on...

338

IODP Expedition 352: Izu-Bonin-Mariana Forearc Week 3 Report (1016 August 2014)  

E-Print Network (OSTI)

the hole, clearing the rotary table at 0730 h (all times presented are ship local time, which is UTC + 9 running tool was unlatched and pulled back up to the rig floor. Next came the assembly of a BHA composed

339

Page 1 of 4 The University of Texas at Arlington  

E-Print Network (OSTI)

-face circular mechanized shield machine, usually of worker-entry diameter, steerable, and with a rotary cutting not applied to those machines where the pressure originates from the main Pipe Jacking rig in the Drive Shaft

Texas at Arlington, University of

340

This document contains the draft version of the following paper: W. Bejgerowski, A. Ananthanarayanan, D. Mueller and S.K. Gupta, "Integrated  

E-Print Network (OSTI)

of a light weight drive-mechanism that can convert the continuous rotary motion of the motor into oscillatory and mechanism design and manufacturing. They concentrated on a robust test rig design rather then a lightweight

Gupta, Satyandra K.

Note: This page contains sample records for the topic "indicators rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

U.S. Energy Information Administration (EIA)  

NLE Websites -- All DOE Office Websites (Extended Search)

for the week positioned storage volumes 816 Bcf above year-ago levels. The natural gas rotary rig count, as reported March 23 by Baker Hughes Incorporated, decreased by 11 to...

342

U.S. Energy Information Administration (EIA)  

NLE Websites -- All DOE Office Websites (Extended Search)

was 78 Bcf, positioning storage volumes 714 Bcf above year-ago levels. The natural gas rotary rig count, as reported February 3 by Baker Hughes Incorporated, decreased by 32 to...

343

An Acquisition and Distribution System for Situational Awareness William E. Green, Paul Y. Oh, and Seunghyun Yoon  

E-Print Network (OSTI)

take over 10 minutes just to lift 20 lbs. Rotary wing aircraft, like helicopters [6] [4] [2], rely images. LEAP consists of a kite fur- nished with a teleoperated camera rig and stabiliza- tion mechanism

Oh, Paul

344

The Centre for Power Transmission  

E-Print Network (OSTI)

, Pitch, Yaw), and any combination of linear or rotary motions can be commanded simultaneously. Cyclic specimen). TWR iterative software is available for accurately matching rig acceleration signals to target

Burton, Geoffrey R.

345

U.S. Energy Information Administration (EIA)  

NLE Websites -- All DOE Office Websites (Extended Search)

the same time last year, according to data released by Baker Hughes Inc. The natural gas rotary rig count totaled 337 as of February 14, a decline of 14 below last week and 84...

346

U.S. Energy Information Administration (EIA)  

NLE Websites -- All DOE Office Websites (Extended Search)

to 3,629 Bcf, according to EIA's Weekly Natural Gas Storage Report. The natural gas rotary rig count, as reported by Baker Hughes Incorporated, was 818 on December 16. This...

347

PRELIMINARY TIME ESTIMATES FOR CORING OPERATIONS  

E-Print Network (OSTI)

EQUATIONS 17 FIGURE 1. DRILL STRING ROUND TRIP 19 FIGURE 2. STANDARD ROTARY CORING (RCB) WIRELINE TRIP 21) WIRELINE TRIP 25 FIGURE 5. ESTIMATED RIGGING, WIRELINE, AND SCANNING TIME FOR REENTRY. 27 #12;Preliminary

348

U.S. Energy Information Administration (EIA)  

Gasoline and Diesel Fuel Update (EIA)

was 192 Bcf, positioning storage volumes 531 Bcf above year-ago levels. The natural gas rotary rig count, as reported by Baker Hughes Incorporated on January 20, fell by 11 to...

349

A High Resolution Micro-Electro-Mechanical Resonant Tilt Sensor  

E-Print Network (OSTI)

-Int Soc Optical Engineering, Bellingham, 2010. [3] W. Jian, G. Guowei, L. Penghua, The Study on Lange-angle CANBUS 2-axis Inclinometer of Rotary Drilling Rig, 2010 2nd IEEE International Conference on Information Management and Engineering (ICIME 2010...

Zou, Xudong; Thiruvenkatanathan, Pradyumna; Seshia, Ashwin A.

2014-01-01T23:59:59.000Z

350

An Aerial Vision Platform for Acquiring Situational Awareness William E. Green and Paul Y. Oh  

E-Print Network (OSTI)

rate of 0.5 ft3 /sec, it would take over 10 minutes to lift 20 lbs. Rotary wing aircraft, like images. LEAP consists of a kite fur- nished with a teleoperated camera rig and stabiliza- tion mechanism

Oh, Paul

351

Abstract--Positional control of pneumatic polymeric Tugger and Twistor actuators is directly accomplished simply by  

E-Print Network (OSTI)

/PLC programming. The objective of this paper is to describe test rigs used to develop and ultimately provide, or Tuggers, as well as rotary actuators, or Twistors, have been described and analyzed in several papers

Nagurka, Mark L.

352

U.S. Energy Information Administration (EIA)  

NLE Websites -- All DOE Office Websites (Extended Search)

levels 31.2% below year-ago levels and 35.3% below the 5-year average. The Baker Hughes rotary rig count totaled 1,860 as of June 6, down 6 units from the previous week. The...

353

Modeling of a Planar Motion Stage for Precision Positioning Kai Treichel**, Remon Al Azrak*, Johann Reger*, and Kai Wulff*  

E-Print Network (OSTI)

commutation. Finally, model characteristics and parameters are identified from experimental test rig data. I (operated in open-loop), to rotary linear drives, planar induction motors, non contact planar brushless DC

Knobloch,Jürgen

354

U.S. Energy Information Administration (EIA)  

NLE Websites -- All DOE Office Websites (Extended Search)

levels 27.4% below year-ago levels and 31.0% below the 5-year average. The Baker Hughes rotary rig count totaled 1,858 as of June 20, up 4 units from the previous week. The...

355

U.S. Energy Information Administration (EIA)  

NLE Websites -- All DOE Office Websites (Extended Search)

for the week positioned storage volumes 799 Bcf above year-ago levels. The natural gas rotary rig count, as reported by Baker Hughes Incorporated on May 4, declined by 7 to 606...

356

U.S. Energy Information Administration (EIA)  

NLE Websites -- All DOE Office Websites (Extended Search)

levels 7.2% below year-ago levels and 3.0% below the 5-year average. The natural gas rotary rig count totaled 375 this week, an increase of 8 from the previous week, according...

357

Effects of alternate fuels report No. 8: analysis of degradiation of magnesia-based refractory bricks from a residual oil-fired rotary cement kiln  

SciTech Connect

Residual oil was used as an alternate fuel to natural gas to supply heat in a rotary cement kiln. Principal impurities in the residual oil were Ca, Fe, Mg, Na, Ni, P.S. and V. the kiln operators were concerned about the effects of these oil impurities on observed degradation of the magnesia-based bricks used as a liner in the burning zone of the kiln. Two degraded bricks, which had been in service for six to nine months, were analyzed to determine the role of fuel impurities on the observed degradation. The maximum hot-face temperature of the refractory during service was about 1500/sup 0/C. One brick had decreased in thickness about 45%, the about 15%. Various analytical measurements on these samples failed to reveal the presence of fuel impurities at or near the hot face of the bricks, and therefore it is concluded that the relatively short service life of these refractories was not due to use of residual oil as the fuel in the kiln. The observed degradation, therefore, was attributed to other reactions and to thermal mechanical conditions in the kiln, which inevitably resulted in extensive erosion of the bricks.

Federer, J.I.; Tennery, V.J.

1980-05-01T23:59:59.000Z

358

Federal Water Use Indices | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Federal Water Use Indices Federal Water Use Indices Federal Water Use Indices FEMP provides water use indices as a guide for Federal agencies. Note that each is a rough estimate of water usage at different types of sites. Your site may vary considerably. The following indices should be used only to assist in determining baseline data when no other information is available on site water usage. Conversion factors for the Federal water use indices are also available. Source: American Water Works Association 1996. Data represents gallons per unit per day. Commercial User Unit Range Typical Airport Passenger 4-5 3 Apartment house Person 100-200 100 Boarding house Person 25-50 40 Hotel Guest 40-60 50 Employee 8-13 10 Lodging house and tourist home Guest 30-50 40 Motel Guest 25-40 35

359

Energy conservation indicators. 1982 annual report  

SciTech Connect

A series of Energy Conservation Indicators were developed for the Department of Energy to assist in the evaluation of current and proposed conservation strategies. As descriptive statistics that signify current conditions and trends related to efficiency of energy use, indicators provide a way of measuring, monitoring, or inferring actual responses by consumers in markets for energy services. Related sets of indicators are presented in some 40 one-page indicator summaries. Indicators are shown graphically, followed by several paragraphs that explain their derivation and highlight key findings. Indicators are classified according to broad end-use sectors: Aggregate (economy), Residential, Commercial, Industrial, Transportation and Electric Utilities. In most cases annual time series information is presented covering the period 1960 through 1981.

Belzer, D.B.

1982-09-01T23:59:59.000Z

360

PREDICTING RANGES FOR PULSARS' BRAKING INDICES  

SciTech Connect

The theoretical determination of braking indices of pulsars is still an open problem. In this paper we report results of a study concerning such determination based on a modification of the canonical model, which admits that pulsars are rotating magnetic dipoles, and on data from the seven pulsars with known braking indices. In order to test the modified model, we predict ranges for the braking indices of other pulsars.

Magalhaes, Nadja S.; Miranda, Thaysa A. [Federal University of Sao Paulo, DCET, Rua Sao Nicolau 210, Diadema, SP 09913-030 (Brazil); Frajuca, Carlos, E-mail: nadjasm@gmail.com [Federal Institute of Education, Science and Technology of Sao Paulo, R. Pedro Vicente 625, Sao Paulo, SP 01109-010 (Brazil)

2012-08-10T23:59:59.000Z

Note: This page contains sample records for the topic "indicators rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

ENVIRONMENTAL INDICATORS FOR CARNEGIE MELLON UNIVERSITY:  

National Nuclear Security Administration (NNSA)

is to use stormwater retention basins. The number of stormwater detention and storage tanks and basins and the capacity of these areas are indicators of the capacity for...

362

Bicycle Generator Lightbar Indicator ----- Inventors William...  

NLE Websites -- All DOE Office Websites (Extended Search)

Bicycle Generator Lightbar Indicator ----- Inventors William Evans (Princeton University), Andrew Zwicker, and Shana Weber (Princeton University) This invention is a series of...

363

residential sector key indicators | OpenEI  

Open Energy Info (EERE)

residential sector key indicators residential sector key indicators Dataset Summary Description This dataset is the 2009 United States Residential Sector Key Indicators and Consumption, part of the Source EIA Date Released March 01st, 2009 (5 years ago) Date Updated Unknown Keywords AEO consumption EIA energy residential sector key indicators Data application/vnd.ms-excel icon 2009 Residential Sector Key Indicators and Consumption (xls, 55.3 KiB) Quality Metrics Level of Review Peer Reviewed Comment Temporal and Spatial Coverage Frequency Annually Time Period License License Open Data Commons Public Domain Dedication and Licence (PDDL) Comment http://www.eia.gov/abouteia/copyrights_reuse.cfm Rate this dataset Usefulness of the metadata Average vote Your vote Usefulness of the dataset Average vote Your vote

364

IRENA Renewable Energy Indicators | Open Energy Information  

Open Energy Info (EERE)

Page Page Edit with form History Facebook icon Twitter icon » IRENA Renewable Energy Indicators Jump to: navigation, search Name Developing the IRENA Renewable Energy Indicators (Phase I) Agency/Company /Organization Worldwatch Institute Partner International Renewable Energy Agency (IRENA) Sector Energy Focus Area Renewable Energy, People and Policy Topics Background analysis, Pathways analysis, Policies/deployment programs Resource Type Publications Program Start 2011 Program End 2012 References IRENA[1] Abstract The Draft Concept Paper for Developing the IRENA Renewable Energy Indicators provides analysis regarding the design of a set of indicators to measure the extent of barriers to renewable energy development and deployment, the effectiveness of enabling policies to remove those barriers, and the impact that renewable energy deployment has on broader development goals. Ultimately, the IRENA Renewable Energy Indicators will be a critical asset in monitoring, tracking, and assessing global developments in the renewable energy sector.

365

Redshift indicators for gamma-ray bursts  

E-Print Network (OSTI)

The measure of the distances and luminosities of gamma-ray bursts (GRBs) led to the discovery that many GRB properties are strongly correlated with their intrinsic luminosity, leading to the construction of reliable luminosity indicators. These GRB luminosity indicators have quickly found applications, like the construction of 'pseudo-redshifts', or the measure of luminosity distances, which can be computed independently of the measure of the redshift. In this contribution I discuss various issues connected with the construction of luminosity-redshift indicators for gamma-ray bursts.

J-L. Atteia

2005-05-04T23:59:59.000Z

366

U.S. Energy Information Administration (EIA)  

Gasoline and Diesel Fuel Update (EIA)

above year-ago levels and 3.0% below the five-year average for this week. The total U.S. rotary rig count decreased by 43 active units to 1,633 rigs for the week ending January...

367

U.S. Energy Information Administration (EIA)  

NLE Websites -- All DOE Office Websites (Extended Search)

below year-ago levels and 6.8% below the five-year average for this week. The total U.S. rotary rig count for the week ending October 31 increased by 2 units to 1,929 rigs,...

368

U.S. Energy Information Administration (EIA)  

Annual Energy Outlook 2012 (EIA)

below year-ago levels and 9.8% below the five-year average for this week. The total U.S. rotary rig count for the week ending November 26 fell by 12 units to 1,917 rigs, according...

369

U.S. Energy Information Administration (EIA)  

Annual Energy Outlook 2012 (EIA)

below year-ago levels and 6.4% below the five-year average for this week. The total U.S. rotary rig count for the week ending November 14 increased by 3 units to 1,928 rigs,...

370

U.S. Energy Information Administration (EIA)  

Gasoline and Diesel Fuel Update (EIA)

above year-ago levels and 1.2% below the five-year average for this week. The total U.S. rotary rig count decreased by 90 active units to 1,543 rigs for the week ending January...

371

U.S. Energy Information Administration (EIA)  

Gasoline and Diesel Fuel Update (EIA)

below year-ago levels and 9.5% below the five-year average for this week. The total U.S. rotary rig count for the week ending December 5 increased by 3 units to 1,920 rigs,...

372

U.S. Energy Information Administration (EIA)  

NLE Websites -- All DOE Office Websites (Extended Search)

above year-ago levels and 5.5% below the five-year average for this week. The total U.S. rotary rig count decreased by 74 units to 1,676 rigs for the week ending January 16,...

373

U.S. Energy Information Administration (EIA)  

NLE Websites -- All DOE Office Websites (Extended Search)

above year-ago levels and 2.1% below the five-year average for this week. The total U.S. rotary rig count decreased by 29 units to 1,811 rigs for the week ending January 2,...

374

U.S. Energy Information Administration (EIA)  

Annual Energy Outlook 2012 (EIA)

above year-ago levels and 7.3% below the five-year average for this week. The total U.S. rotary rig count for the week ending December 12 decreased by 27 units to 1,893 rigs,...

375

U.S. Energy Information Administration (EIA)  

Gasoline and Diesel Fuel Update (EIA)

below year-ago levels and 6.2% below the five-year average for this week. The total U.S. rotary rig count for the week ending November 7 fell by 4 units to 1,925 rigs, according...

376

IODP Expedition 342: Paleogene Newfoundland Sediment Drifts Week 1 Report (1-9 June 2012)  

E-Print Network (OSTI)

and pressure signals were successfully transmitted to the rig floor and recorded. After circulation was re from the hole. The bit cleared the rotary table at 0110 h ending Hole U1402A. #12;Since barrel on the rig floor and placed into split liner sections. The coring system was disassembled

377

U.S. Energy Information Administration (EIA)  

NLE Websites -- All DOE Office Websites (Extended Search)

above year-ago levels and 3.8% below the five-year average for this week. The total U.S. rotary rig count decreased by 61 units to 1,750 rigs for the week ending January 9,...

378

U.S. Energy Information Administration (EIA)  

Gasoline and Diesel Fuel Update (EIA)

levels 24.4% below year-ago levels and 27.6% below the 5-year average. The Baker Hughes rotary rig count increased week-over-week by 1 rig, to 1,874 as of July 3. The number of...

379

IODP Expedition 328: Cascadia Subduction Zone ACORK Observatory Site U1364 Summary  

E-Print Network (OSTI)

(VIT) was deployed to observe the bit contacting the seafloor at 1329.0 m below rig floor (mbrf to the rig floor. After jetting in the 16 inch casing and re-entry cone, our next objective was to drill a 14) mud. The drill string was recovered with the bit clearing the rotary table at 1435 hr on 14 September

380

IODP Expedition 352: Izu-Bonin-Mariana Forearc Week 5 Report (2430 August 2014)  

E-Print Network (OSTI)

of Expedition 352 (IBM Forearc) began while pulling the drill string out of Hole U1440B. The rotary core barrel (RCB) bit cleared the seafloor at 0100 h on 24 August 2014 and was back on the rig floor at 0945 h casing at 96 mbsf. The triple combo tool string was rigged up with the Ultrasonic Borehole Imager (UBI

Note: This page contains sample records for the topic "indicators rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

The Use of WBM to Improve ROP in HTHP/Hard Rock Environments  

E-Print Network (OSTI)

on bit (WOB) and rotary speed (RPM) that are applied when drilling. These properties are dependent on the drillstring design and the available power of the drilling rig. Drillstring design has a direct effect on WOB the size and number of drill... Page VITA .......................................................................................................................... 65 vii vii LIST OF FIGURES Page Figure 1 Various Rotary Drilling Bits From Left: Tri-Cone Insert...

Kraussman, Andrew

2012-07-16T23:59:59.000Z

382

To link to this article : DOI:10.1016/j.wear.2014.04.023 URL : http://dx.doi.org/10.1016/j.wear.2014.04.023  

E-Print Network (OSTI)

-speed test rig was designed to simulate the interactions between labyrinth seals and abradable coatings enhancement, we investigated the clearance reduction between the rotary parts in air systems, the successive between a rotary seal, known as a labyrinth seal, and a turbo-engine housing coated with a sacrificial

383

Benchmarking Sustainability: the use of Indicators  

E-Print Network (OSTI)

Benchmarking Sustainability: the use of Indicators Introduction The concept of sustainable development is both very popular and elusive. The overwhelming appeal of sustainability is situated to build a generally shared perception of sustainable development (Butler, 1998). For many people

Zaferatos, Nicholas C.

384

Societal health and urban sustainability indicators  

SciTech Connect

Without the social will, no city can successfully Undertake the planning and programs necessary for meaningful progress toward sustainability. Social will derives from wellsprings of vital societal health. This paper presents an approach to helping cities in APEC member economies initiate a program for developing indicators of sustainability. Representative indicators of social capital and other aspects of civic engagement, as proxies for societal health, are presented.

Petrich, C.H.; Tonn, B.E.

1996-08-27T23:59:59.000Z

385

Optical temperature indicator using thermochromic semiconductors  

DOE Patents (OSTI)

A reversible optical temperature indicator utilizes thermochromic semiconductors which vary in color in response to various temperature levels. The thermochromic material is enclosed in an enamel which provides protection and prevents breakdown at higher temperatures. Cadmium sulfide is the preferred semiconductor material. The indicator may be utilized as a sign or in a striped arrangement to clearly provide a warning to a user. The various color responses provide multiple levels of alarm.

Kronberg, J.W.

1995-01-01T23:59:59.000Z

386

Fluid dynamics kill Wyoming icicle  

SciTech Connect

Control of a blowout in which a portion of the drill collar string was extending through the rotary table and into the derrick was compounded by ice building up on the derrick and substructure. However, the momentum kill procedure proved successful. Topics considered in this paper include oil wells, natural gas wells, sleeves, rotary drills, drilling rigs, fluid mechanics, occupational safety, blowouts, drill pipes, rotary drilling, ice removal, and freezing.

Grace, R.D.

1987-04-01T23:59:59.000Z

387

Lanthanide-halide based humidity indicators  

DOE Patents (OSTI)

The present invention discloses a lanthanide-halide based humidity indicator and method of producing such indicator. The color of the present invention indicates the humidity of an atmosphere to which it is exposed. For example, impregnating an adsorbent support such as silica gel with an aqueous solution of the europium-containing reagent solution described herein, and dehydrating the support to dryness forms a substance with a yellow color. When this substance is exposed to a humid atmosphere the water vapor from the air is adsorbed into the coating on the pore surface of the silica gel. As the water content of the coating increases, the visual color of the coated silica gel changes from yellow to white. The color change is due to the water combining with the lanthanide-halide complex on the pores of the gel.

Beitz, James V. (Hinsdale, IL); Williams, Clayton W. (Chicago, IL)

2008-01-01T23:59:59.000Z

388

Performance Indicators of Wind Energy Production  

E-Print Network (OSTI)

Modeling wind speed is one of the key element when dealing with the production of energy through wind turbines. A good model can be used for forecasting, site evaluation, turbines design and many other purposes. In this work we are interested in the analysis of the future financial cash flows generated by selling the electrical energy produced. We apply an indexed semi-Markov model of wind speed that has been shown, in previous investigation, to reproduce accurately the statistical behavior of wind speed. The model is applied to the evaluation of financial indicators like the Internal Rate of Return, semi-Elasticity and relative Convexity that are widely used for the assessment of the profitability of an investment and for the measurement and analysis of interest rate risk. We compare the computation of these indicators for real and synthetic data. Moreover, we propose a new indicator that can be used to compare the degree of utilization of different power plants.

D'Amico, G; Prattico, F

2015-01-01T23:59:59.000Z

389

Federal Technical Capability Program - Quarterly Performance Indicator  

NLE Websites -- All DOE Office Websites (Extended Search)

Quarterly Performance Indicator Reports Quarterly Performance Indicator Reports 2013 Quarterly Report on Federal Technical Capability August 16, 2013 Quarterly Report on Federal Technical Capability June 5, 2013 Quarterly Report on Federal Technical Capability February 20, 2013 2012 Quarterly Report on Federal Technical Capability November 20, 2012 Quarterly Report on Federal Technical Capability August 8, 2012 Quarterly Report on Federal Technical Capability May 30, 2012 Quarterly Report on Federal Technical Capability March 6, 2012 2011 Quarterly Report on Federal Technical Capability November 10, 2011 Quarterly Report on Federal Technical Capability August 24, 2011 Quarterly Report on Federal Technical Capability May 18, 2011 Quarterly Report on Federal Technical Capability February 23, 2011

390

Exergy indicators in the building environment  

Science Journals Connector (OSTI)

The objective of this work is the application of the exergy analysis to the building sector and the introduction of suitable exergy indicators. The indicators are tools which are representative of the system under study and provide reliability over time, information to policy makers and awareness of potential environmental problems arising from human activities. The application of the exergy analysis of a new office building's life cycle in Greece constitutes a big part of this work. A hypothetical case involving the application of renewable energy sources in a range of 10-50% of the overall exergy needs is examined.

C. Koroneos; I. Kalemakis

2012-01-01T23:59:59.000Z

391

Performance indicators, third quarter CY-1991  

SciTech Connect

Secretary of Energy Notice (SEN-29-91) directed that a Department- wide uniform system of Performance Indicators (PI's) for trending and analyzing operational data to help assess and support progress in improving performance and in strengthening line management control of operations relating to environmental safety, and health activities'' be developed. This Performance Indicator Report represents a compilation of data for the third quarter of calendar year 1991 for the following Lawrence Berkeley Laboratory (LBL) facilities: (1) Bevalac, (2) 88-Inch Cyclotron, (3) Materials Sciences Division.

Not Available

1992-01-01T23:59:59.000Z

392

Performance indicators, third quarter CY-1991  

SciTech Connect

Secretary of Energy Notice (SEN-29-91) directed that a Department- wide ``uniform system of Performance Indicators (PI`s) for trending and analyzing operational data to help assess and support progress in improving performance and in strengthening line management control of operations relating to environmental safety, and health activities`` be developed. This Performance Indicator Report represents a compilation of data for the third quarter of calendar year 1991 for the following Lawrence Berkeley Laboratory (LBL) facilities: (1) Bevalac, (2) 88-Inch Cyclotron, (3) Materials Sciences Division.

Not Available

1992-01-01T23:59:59.000Z

393

Reusable tamper-indicating security seal  

SciTech Connect

A reusable tamper-indicating mechanical security seal for use in safeguarding nuclear material has been developed. The high-security seal displays an unpredictable, randomly selected, five-digit code each time it is used. This five digit code serves the same purpose that the serial number does for conventional non-reusable seals - a unique identifier for each use or application. The newly developed reusable seal is completely enclosed within a seamless, tamper-indicating, plastic jacket. The jacket is designed to reveal any attempts to penetrate, section or to chemically remove and replace with a counterfeit for surreptitious purposes.

Ryan, M.J.

1981-01-01T23:59:59.000Z

394

Reduction of iron-oxide-carbon composites: part II. Rates of reduction of composite pellets in a rotary hearth furnace simulator  

SciTech Connect

A new ironmaking concept is being proposed that involves the combination of a rotary hearth furnace (RHF) with an iron-bath smelter. The RHF makes use of iron-oxide-carbon composite pellets as the charge material and the final product is direct-reduced iron (DRI) in the solid or molten state. This part of the research includes the development of a reactor that simulated the heat transfer in an RHF. The external heat-transport and high heating rates were simulated by means of infrared (IR) emitting lamps. The reaction rates were measured by analyzing the off-gas and computing both the amount of CO and CO{sub 2} generated and the degree of reduction. The reduction times were found to be comparable to the residence times observed in industrial RHFs. Both artificial ferric oxide (PAH) and naturally occurring hematite and taconite ores were used as the sources of iron oxide. Coal char and devolatilized wood charcoal were the reductants. Wood charcoal appeared to be a faster reductant than coal char. However, in the PAH-containing pellets, the reverse was found to be true because of heat-transfer limitations. For the same type of reductant, hematite-containing pellets were observed to reduce faster than taconite-containing pellets because of the development of internal porosity due to cracking and fissure formation during the Fe2O{sub 3}-to-Fe3O{sub 4} transition. This is, however, absent during the reduction of taconite, which is primarily Fe3O{sub 4}. The PAH-wood-charcoal pellets were found to undergo a significant amount of swelling at low-temperature conditions, which impeded the external heat transport to the lower layers. If the average degree of reduction targeted in an RHF is reduced from 95 to approximately 70 pct by coupling the RHF with a bath smelter, the productivity of the RHF can be enhanced 1.5 to 2 times. The use of a two- or three-layer bed was found to be superior to that of a single layer, for higher productivities.

Halder, S.; Fruehan, R.J. [Praxair Inc., Tonawanda, NY (United States). Praxair Technological Center

2008-12-15T23:59:59.000Z

395

Monitoring change in biodiversity through composite indices  

E-Print Network (OSTI)

Monitoring change in biodiversity through composite indices S.T. Buckland1,*, A.E. Magurran2 , R Zealand The need to monitor trends in biodiversity raises many technical issues. What are the features of a good biodiversity index? How should trends in abundance of individual species be estimated? How should

Buckland, Steve

396

Targets and indicators for gene level biodiversity  

E-Print Network (OSTI)

Targets and indicators for gene level biodiversity Resilience and future adaptation in forests, inland waters and marine environments depend on genetic variation Welcome to the Side-event on Lunch.weibull@naturvardsverket.se BaltGene­BalticSeaGeneticBiodiversity www.tmbl.gu.se:16080/baltgene GeneticMonitoring http

397

SRR Ecological Assessment Indicators: Selection and  

E-Print Network (OSTI)

, Soil aggregate stability · Water - Surface water frequency, Volume · Plants - Key species, Invasives, Pounds of domestic meat produced, Pounds of harvestable materials produced #12;Why these indicators in cover or stability is expected from better management. #12;Surface Water Availability · Water is vital

Wyoming, University of

398

INDICES OF MEAN MONTHLY GEOSTROPHIC WIND  

E-Print Network (OSTI)

323 '*'-'· INDICES OF MEAN MONTHLY GEOSTROPHIC WIND OVER THE NORTH PACIFIC OCEAN Marine Biological OF THE INTERIOR FISH AND WILDLIFE SERVICE #12;Explanatory Note The series embodies results of investigations;United States Department of the Interior, Fred A. Seaton, Secretary Fish and Wildlife Service, Arnie J

399

Oxygen Detection via Nanoscale Optical Indicators  

E-Print Network (OSTI)

Oxygen Detection via Nanoscale Optical Indicators Ruby N. Ghosh Dept. of Physics Michigan State University East Lansing, MI, USA weekschr@msu.edu Abstract--Oxygen plays a ubiquitous role in terrestrial developed an optical technique for monitoring oxygen in both gas and liquid phases utilizing nanoscale metal

Ghosh, Ruby N.

400

Approximated Distributions of Sampling Inequality Indices  

Science Journals Connector (OSTI)

Often, in finite samples, the true level of the confidence intervals for natural estimators of inequality indices belonging to the Gini family differs greatly from their nominal level, which is based on the asymptotic confidence limits. This paper ... Keywords: Gini index family, Gram-Charlier approximation, Monte Carlo experiment, algebraic computer software, income distribution

Paola Palmitesta; Corrado Provasi; Cosimo Spera

1999-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "indicators rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

New fuzzy indices for multidimensional poverty  

Science Journals Connector (OSTI)

Poverty is a complex phenomenon that cannot be reduced solely to monetary dimension. This leads to the need for a multidimensional approach that consists in extending the analysis to a variety of non-monetary indicators of living conditions. The axiomatic ... Keywords: Fuzzy Sets, Membership Function, Poverty, Poverty Line, Weighted Mean, Weights

Besma Belhadj

2013-05-01T23:59:59.000Z

402

FTCP Quarterly Indicator Reports | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Assistance » Federal Technical Capability Program » Assistance » Federal Technical Capability Program » FTCP Quarterly Indicator Reports FTCP Quarterly Indicator Reports November 20, 2013 FTCP Quarterly Report on Federal Technical Capability, November 20, 2013 This Quarterly Report on the Federal Technical Capability Program (FTCP) contains information on the status of qualifications in the Technical Qualification Program (TQP) and technical skill gaps, on a quarterly basis. Report also displays trend data for overall TQP qualification and staffing shortfalls. August 16, 2013 FTCP Quarterly Report on Federal Technical Capability, August 16, 2013 This Quarterly Report on the Federal Technical Capability Program (FTCP) contains information on the status of qualifications in the Technical Qualification Program (TQP) and technical skill gaps, on a quarterly basis.

403

National Climate Assessment Indicators: Background, Development, & Examples  

SciTech Connect

Indicators are usually thought of as measurements or calculations that represent important features of the status, trend, or performance of a system of interest (e.g. the economy, agriculture, air quality). They are often used for the most practical of reasons – one cannot measure everything important about systems of interest, so there is a practical need to identify major features that can be reported periodically and used to guide both research and decisions (NRC 2000).

Janetos, Anthony C.; Chen, Robert; Arndt, Deke; Kenney, Melissa A.; Abbasi, Daniel; Armstrong, Tom; Bartuska, Ann; Blair, Maria; Buizer, Jim; Dietz, Tom; Easterling, Dave; Kaye, Jack; Kolian, Michael; McGeehin, Michael; O'Connor, Robert; Pulwarty, Roger; Running, Steve; Schmalensee, Dick; Webb, Robert; Weltzin, Jake; Baptista, Sandra; Enquist, Carolyn A.; Janetos, Anthony C.; Chen, Robert; Arndt, Deke; Hatfield, Jerry; Hayes, Mark L.; Jones, K. Burce; McNutt, Chad; Meier, Wayne R.; Schwartz, Mark D.; Svoboda, Mark

2012-02-28T23:59:59.000Z

404

Ecological indicators for stream restoration success  

Science Journals Connector (OSTI)

Exploitation of freshwater resources is essential for sustenance of human existence and alteration of rivers, lakes and wetlands has facilitated economic development for centuries. Consequently, freshwater biodiversity is critically threatened, with stream ecosystems being the most heavily affected. To improve the status of freshwater habitats, e.g. in the context of the European Water Framework Directive and the US Clean Water Act, it is essential to implement the most effective restoration measures and identify the most suitable indicators for restoration success. Herein, several active and passive bioindication approaches are reviewed in light of existing legal frameworks, current targets and applicable implementation of river restoration. Such approaches should move from the use of single biological indicators to more holistic ecological indicators simultaneously addressing communities, multiple life stages and habitat properties such as water quality, substrate composition and stream channel morphology. The proposed Proceeding Chain of Restoration (PCoR) can enable the integration of natural scientific, political and socioeconomic dimensions for restoration of aquatic ecosystems and associated services. Generally, an analysis that combines target species-based active bioindication with community-based passive bioindication and multivariate statistics seems to be most suitable for a holistic evaluation of restoration success, as well as for the monitoring of stream ecosystem health. Since the response of biological communities to changing environmental conditions can differ between taxonomic groups and rivers, assessments at the ecosystem scale should include several levels of biological organisation. A stepwise evaluation of the primary factors inducing disturbance or degradation is needed to integrate increasing levels of complexity from water quality assessments to the evaluation of ecological function. The proposed \\{PCoR\\} can provide a step-by-step guide for restoration ecologists, comprising all planning steps from the determination of the conservation objectives to the use of ecological indicators in post-restoration monitoring.

Joachim Pander; Juergen Geist

2013-01-01T23:59:59.000Z

405

Mexican energy policy and sustainability indicators  

Science Journals Connector (OSTI)

The authors analyze the Mexican energy policy taking as reference the methodological framework for sustainable energy development proposed by the Economic Commission for Latin America and the Caribbean. This methodology takes eight related indicators to the social, environmental and economic dimensions in order to calculate a general sustainability indicator for the energy sector. In this methodology, the weight of each dimension is different; namely, the social and environmental issues have less relevance than the economic issues. The authors use this methodology because government institutions as the Department of Energy and the Department of Environment and Natural Resources have used some indicators from such a methodology to propose plans, programs, projects and bills. Authors know of the existence of other methodologies about sustainability. Nonetheless, opting for the Economic Commission for Latin America and the Caribbean's methodology is convenient because this organization is a respectable authority for civil servants from the Mexican institutions. Our objective is just to contrast the sustainability grade of the energy sector between 1990 and 2008 for Mexico whose government started reforms in the 1990s. It concludes that those reforms did not bring about a higher sustainability level for the energy sector.

Claudia Sheinbaum-Pardo; Belizza Janet Ruiz-Mendoza; Víctor Rodríguez-Padilla

2012-01-01T23:59:59.000Z

406

Fundamental Aeronautics Subsonic Rotary Wing  

E-Print Network (OSTI)

services to society, including emergency medical and rescue services, security patrols, off-shore oil

407

Computational Reality XV Rotary viscometer  

E-Print Network (OSTI)

by applied forces on the surface and any volumetric forces, like gravitation or electromagnetic field proposed an apparent viscosity depending on the aforementioned component, d12, given by a power law: 12 = µ

Berlin,Technische Universität

408

Conveyor with rotary airlock apparatus  

DOE Patents (OSTI)

This invention is comprised of an apparatus for transferring objects from a first region to a second region, the first and second regions having differing atmospheric environments. The apparatus includes a shell having an entrance and an exit, a conveyer belt running through the shell from the entrance to the exit, and a horizontally mounted `revolving door` with at least four vanes revolving about its axis. The inner surface of the shell and the top surface of the conveyer belt act as opposing walls of the `revolving door`. The conveyer belt dips as it passes under but against the revolving vanes so as not to interfere with them but to engage at least two of the vanes and define thereby a moving chamber. Preferably, the conveyer belt has ridges or grooves on its surface that engage the edges of the vanes and act to rotate the vane assembly. Conduits are provided that communicate with the interior of the shell and allow the adjustment of the atmosphere of the moving chamber or recovery of constituents of the atmosphere of the first region from the moving chamber before they escape to the second region.

Kronbert, J.W.

1993-01-01T23:59:59.000Z

409

Rotary powder feed through apparatus  

DOE Patents (OSTI)

A device for increasing the uniformity of solids within a solids fabrication system, such as a direct light fabrication (DLF) system in which gas entrained powders are passed through the focal point of a moving high-power light which fuses the particles in the powder to a surface being built up in layers. The invention provides a feed through interface wherein gas entrained powders input from stationary input lines are coupled to a rotating head of the fabrication system. The invention eliminates the need to provide additional slack in the feed lines to accommodate head rotation, and therefore reduces feed line bending movements which induce non-uniform feeding of gas entrained powder to a rotating head.

Lewis, Gary K. (Los Alamos, NM); Less, Richard M. (Los Alamos, NM)

2001-01-01T23:59:59.000Z

410

The advanced flame quality indicator system  

SciTech Connect

By combining oil tank monitoring, systems diagnostics and flame quality monitoring in an affordable system that communicates directly with dealers by telephone modem, Insight Technologies offers new revenue opportunities and the capability for a new order of customer relations to oil dealers. With co-sponsorship from New York State Energy Research and Development Authority, we have incorporated several valuable functions to a new product based on the original Flame Quality Indicator concept licensed from the US DOE`s Brookhaven National Laboratory. The new system is the Advanced Flame Quality Indicator, or AFQI. As before, the AFQI monitors and reports the intensity of the burner flame relative to a calibration established when the burner is set up at AFQI installation. Repairs or adjustments are summoned by late-night outgoing telephone calls when limits are exceeded in either direction, indicating an impending contamination or other malfunction. A independently, a pressure transducer for monitoring oil tank level and filter condition, safety lockout alarms and a temperature monitor; all reporting automatically at instructed intervals via an on-board modem to a central station PC computer (CSC). Firmware on each AFQI unit and Insight-supplied software on the CSC automatically interact to maintain a customer database for an oil dealer, an OEM, or a regional service contractor. In addition to ensuring continuously clean and efficient operation, the AFQI offers the oil industry a new set of immediate payoffs, among which are reduced outages and emergency service calls, shorter service calls from cleaner operation, larger oil delivery drops, the opportunity to stretch service intervals to as along as three years in some cases, new selling features to keep and attract customers, and greatly enhanced customer contact, quality and reliability.

Oman, R.; Rossi, M.J.; Calia, V.S.; Davis, F.L.; Rudin, A. [Insight Technologies, Inc., Bohemia, NY (United States)

1997-09-01T23:59:59.000Z

411

FIELD TEST OF THE FLAME QUALITY INDICATOR  

SciTech Connect

The flame quality indicator concept was developed at BNL specifically to monitor the brightness of the flame in a small oil burner and to provide a ''call for service'' notification when the brightness has changed from its setpoint, either high or low. In prior development work BNL has explored the response of this system to operational upsets such as excess air changes, fouled atomizer nozzles, poor fuel quality, etc. Insight Technologies, Inc. and Honeywell, Inc. have licensed this technology from the U.S. Department of Energy and have been cooperating to develop product offerings which meet industry needs with an optimal combination of function and price. Honeywell has recently completed the development of the Flame Quality Monitor (FQM or Honeywell QS7100F). This is a small module which connects via a serial cable to the burners primary operating control. Primary advantages of this approach are simplicity, cost, and ease of installation. Call-for-service conditions are output in the form of front panel indicator lights and contact closure which can trigger a range of external communication options. Under this project a field test was conducted of the FQM in cooperation with service organizations in Virginia, Pennsylvania, New Jersey, New York, and Connecticut. At total of 83 field sites were included. At each site the FQM was installed in parallel with another embodiment of this concept--the Insight AFQI. The AFQI incorporates a modem and provides the ability to provide detailed information on the trends in the flame quality over the course of the two year test period. The test site population was comprised of 79.5% boilers, 13.7% warm air furnaces, and 6.8% water heaters. Nearly all were of residential size--with firing rates ranging from 0.6 gallons of oil per hour to 1.25. During the course of the test program the monitoring equipment successfully identified problems including: plugged fuel lines, fouled nozzles, collapsed combustion chambers, and poor fuel pump cut-off. Service organizations can use these early indications to reduce problems and service costs. There were also some ''call-for-service'' indications for which problems were not identified. The test program also showed that monitoring of the flame can provide information on burner run times and this can be used to estimate current oversize factors and to determine actual fuel usage, enabling more efficient fuel delivery procedures.

Andrew M. Rudin; Thomas Butcher; Henry Troost

2003-02-04T23:59:59.000Z

412

Cosmological data and indications for new physics  

SciTech Connect

Data from the Atacama Cosmology Telescope (ACT) and the South Pole Telescope (SPT), combined with the nine-year data release from the WMAP satellite, provide very precise measurements of the cosmic microwave background (CMB) angular anisotropies down to very small angular scales. Augmented with measurements from Baryonic Acoustic Oscillations surveys and determinations of the Hubble constant, we investigate whether there are indications for new physics beyond a Harrison-Zel'dovich model for primordial perturbations and the standard number of relativistic degrees of freedom at primordial recombination. All combinations of datasets point to physics beyond the minimal Harrison-Zel'dovich model in the form of either a scalar spectral index different from unity or additional relativistic degrees of freedom at recombination (e.g., additional light neutrinos). Beyond that, the extended datasets including either ACT or SPT provide very different indications: while the extended-ACT (eACT) dataset is perfectly consistent with the predictions of standard slow-roll inflation, the extended-SPT (eSPT) dataset prefers a non-power-law scalar spectral index with a very large variation with scale of the spectral index. Both eACT and eSPT favor additional light degrees of freedom on top of the Harrison-Zel'dovich model. eACT is consistent with zero neutrino masses, while eSPT favors nonzero neutrino masses at more than 95% confidence.

Benetti, Micol [Physics Department and ICRA, Università di Roma ''La Sapienza'', Ple. Aldo Moro 2, 00185, Rome (Italy); Gerbino, Martina; Melchiorri, Alessandro; Pagano, Luca [Physics Department and INFN, Università di Roma ''La Sapienza'', Ple Aldo Moro 2, 00185, Rome (Italy); Kinney, William H. [Department of Physics, University at Buffalo, the State University of New York, Buffalo, NY 14260-1500 (United States); Kolb, Edward W. [Department of Astronomy and Astrophysics, Enrico Fermi Institute, and Kavli Institute for Cosmological Physics, University of Chicago, Chicago, Illinois 60637-1433 (United States); Lattanzi, Massimiliano [Dipartimento di Fisica e Science della Terra, Università di Ferrara and INFN, sezione di Ferrara, Polo Scientifico e Tecnologico - Edificio C Via Saragat, 1, I-44122 Ferrara Italy (Italy); Riotto, Antonio, E-mail: micol.benetti@roma1.infn.it, E-mail: martina.gerbino@roma1.infn.it, E-mail: whkinney@buffalo.edu, E-mail: Rocky.Kolb@uchicago.edu, E-mail: lattanzi@fe.infn.it, E-mail: alessandro.melchiorri@roma1.infn.it, E-mail: luca.pagano@roma1.infn.it, E-mail: antonio.riotto@unige.ch [Department of Theoretical Physics and Center for Astroparticle Physics (CAP) 24 quai E. Ansermet, CH-1211 Geneva 4 (Switzerland)

2013-10-01T23:59:59.000Z

413

Natural Gas - U.S. Energy Information Administration (EIA) - U.S. Energy  

Gasoline and Diesel Fuel Update (EIA)

23, 2012 | Release Date: May 24, 23, 2012 | Release Date: May 24, 2012 | Next Release: May 31, 2012 Previous Issues Week: 01/19/2014 (View Archive) JUMP TO: In The News | Overview | Prices/Demand/Supply | Storage In the News: Natural Gas Rig Count Briefly Drops Below 600. The natural gas rotary rig count, as reported by Baker Hughes Incorporated, rose by 2 this week to 600, after falling to a 10-year low of 598 last week. After increasing modestly to 936 active rigs in the fall of 2011, the natural gas rig count has dropped sharply. The oil rig count, currently at 1,382, has generally risen steadily since 2009, largely in response to increasing crude oil prices. Natural gas rigs are currently down about 31 percent from their level at the same time last year, while oil rigs have risen by 45 percent over the

414

Sustainability indicator systems within urban governance: Usability analysis of sustainability indicator systems as boundary objects  

Science Journals Connector (OSTI)

Abstract While sustainability indicator systems (SIs) have proven to be valuable rational tools for improving the availability of information related to the relationship of cities and communities to natural limits, the indicators movement has achieved limited instrumental uptake in policy. This paper begins from a recognition that instrumental use of sustainability indicator systems is rare. Greater potential impact exists for \\{SIs\\} designed to be much more attentive to their conceptual and political values within their particular social and political context. In other words, greater attention to what has been called the governance of indicator systems, or the ways in which \\{SIs\\} fit as policy tools within a multilevel and multiactor governance context, is key to increasing their utility. This is particularly true given the need for decisive policy change, or even the introduction of a new development path, which is asserted within the sustainability agenda. Understanding the real and potential utility of indicator systems within multiactor governance processes, in which their roles are primarily rhetorical, conceptual and political, is facilitated by thinking about indicator systems as boundary objects, tools which open up dialogue, information sharing, learning and consensus-building across different policy boundaries: between experts and nonexperts, formal government and different nongovernment actors, higher-order governments and lower-order governments. This paper offers a comparative analysis of three sustainability indicator systems in the North American context – Vancouver's Vital Signs (Vancouver Foundation), Seattle's Happiness Initiative, and LEED-ND (US Green Building Council) – all of which have shown some success in operationalizing a new policy boundary as a means of making conceptual and political contributions to governance practices. The specific boundaries operationalized, the different approach taken by each project, and the usability demonstrated by each project at that boundary in terms of salience, legitimacy and credibility, are assessed comparatively. In general, the trajectory in design and use of ecological and sustainability indicators demonstrates an increase in appetite, aptitude and numbers of channels for use in processes of governance; however, these factors vary with the local social–political opportunity structure. This analysis presents the advances made as well as the tradeoffs evident in these cases across the gamut of different forms of usability of nongovernmental indicator systems designed for use as boundary objects, and suggests a path forward for indicator work which aims to change policy, from a governance perspective.

Meg Holden

2013-01-01T23:59:59.000Z

415

EVSE Features Charge Delay Option Power Light Indicator Eight-segment Progress Indicator Auto-restart  

NLE Websites -- All DOE Office Websites (Extended Search)

Charge Delay Option Power Light Indicator Charge Delay Option Power Light Indicator Eight-segment Progress Indicator Auto-restart EVSE Specifications Grid connection Plug and cord NEMA 6-50 Connector type J1772 Test lab certifications UL Listed Approximate size (H x W x D inches) 10 x 13 x 4 Charge level AC Level 2 Input voltage 240 VAC Maximum input current 30 Amp Circuit breaker rating 40 Amp Test Conditions 1 Test date 10/30/2012 Nominal supply voltage (Vrms) 209.04 Supply frequency (Hz) 59.99 Initial ambient temperature (°F) 64 Test Vehicle 1,3 Make and model 2012 Chevrolet Volt Battery type Li-ion Steady state charge power (AC kW) 3.09 Maximum charge power (AC kW) 3.20 EVSE Test Results 1,2,4

416

Review of sustainability indices and indicators: Towards a new City Sustainability Index (CSI)  

SciTech Connect

The purpose of this paper is to discuss conceptual requirements for a City Sustainability Index (CSI) and to review existing major sustainability indices/indicators in terms of the requirements. The following indices are reviewed: Ecological Footprint (EF), Environmental Sustainability Index (ESI), Dashboard of Sustainability (DS), Welfare Index, Genuine Progress Indicator (GPI), Index of Sustainable Economic Welfare, City Development Index, emergy/exergy, Human Development Index (HDI), Environmental Vulnerability Index (EVI), Environmental Policy Index (EPI), Living Planet Index (LPI), Environmentally-adjusted Domestic Product (EDP), Genuine Saving (GS), and some applications of composite indices or/and multivariate indicators to local or regional context as case studies. The key conceptual requirements for an adequate CSI are: (i) to consider environmental, economic and social aspects (the triple bottom line of sustainability) from the viewpoint of strong sustainability; (ii) to capture external impacts (leakage effects) of city on other areas beyond the city boundaries particularly in terms of environmental aspects; (iii) to create indices/indicators originally for the purpose of assessing city sustainability; and (iv) to be able to assess world cities in both developed and developing countries using common axes of evaluation. Based on the review, we conclude that it is necessary to create a new CSI that enables us to assess and compare cities' sustainability performance in order to understand the global impact of cities on the environment and human life as compared with their economic contribution. In the future, the CSI will be able to provide local authorities with guidance toward sustainable paths. - Highlights: Black-Right-Pointing-Pointer We derive the four key requirements for a new City Sustainability Index (CSI) system. Black-Right-Pointing-Pointer First, the triple bottom line must be considered in terms of strong sustainability. Black-Right-Pointing-Pointer Second, environmental leakage effects beyond city boundaries should be captured. Black-Right-Pointing-Pointer Third, 'city sustainability' should be originally considered when CSI is created. Black-Right-Pointing-Pointer Fourth, cities in developed and developing countries can be evaluated without bias.

Mori, Koichiro, E-mail: kmori@iis.u-tokyo.ac.jp [Institute of Industrial Science, University of Tokyo (Japan); Christodoulou, Aris, E-mail: aris.christodoulou@ucl.ac.uk [Centre for Transport Studies, University College London (United Kingdom)

2012-01-15T23:59:59.000Z

417

Systems Engineering Leading Indicators Guide, Version 1.0  

E-Print Network (OSTI)

The Systems Engineering Leading Indicators guide set reflects the initial subset of possible indicators that were considered to be the highest priority for evaluating effectiveness before the fact. A leading indicator is ...

Lean Advancement Initiative

2013-10-31T23:59:59.000Z

418

Electric Motor Emulator Versus Rotating Test Rig  

Science Journals Connector (OSTI)

A controversial issue among experts is whether real-time model-based electric motor emulation can replace a conventional rotating test ... a complete inverter test system with an integrated electric motor emulato...

Dipl.-Ing. (FH) Horst Hammerer; Dipl.-Ing. (FH) Dieter Strauss

2012-06-01T23:59:59.000Z

419

Human rigHts advocacy in action  

E-Print Network (OSTI)

in memoriam 26 2 nonesuch//Autumn 2011 Greencoat 80 Silk is carbon balanced ­ where the carbon intensity has purchased. Carbon balancing by the World Land Trust tackles climate change through projects that both offset 18 Brave new world 22 thought that counts 27 In pictures snapshots 5 taken 29 Regulars Bristol

Bristol, University of

420

The Five Offshore Drilling Rig Markets  

Science Journals Connector (OSTI)

Market valuations are performed by a number of industry consultancies (e.g. Douglas-Westwood, GBI Research, IHS, R.S. Platou, Rystad Energy, Wood Mackenzie). Comparisons across firms depend...7, 18]. Large market...

Mark J. Kaiser; Brian F. Snyder

2013-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "indicators rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Hoisting and Rigging Technical Advisory Committee Membership...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Isaac DOE, Los Alamos Site Office imvaldez@doeal.gov (505) 664-0285 Viola, Michael Princeton Plasma Physics Lab mviola@pppl.gov (609) 243-3655 Wang, Y. T NNSA, Livermore...

422

Computer Simulations Indicate Calcium Carbonate Has a Dense Liquid...  

NLE Websites -- All DOE Office Websites (Extended Search)

Computer Simulations Indicate Calcium Carbonate Has a Dense Liquid Phase Computer Simulations Indicate Calcium Carbonate Has a Dense Liquid Phase Berkeley Lab research could help...

423

Sustainability Indicators for Discrete Manufacturing Processes Applied to Grinding Technology  

E-Print Network (OSTI)

the data into three sustainability indicators for eachor into one total sustainability indicator. The weighting isAn overview of sustainability assessment methodologies,

Linke, Barbara S.; Corman, Gero J.; Dornfeld, David A.; Tönissen, Stefan

2013-01-01T23:59:59.000Z

424

Blow out preventer handling system  

SciTech Connect

A system for testing and installing a blow out preventer on a floating vessel and offshore drilling rigs, although the system may be used on other rotary drilling rigs, is disclosed. Retractable rotary table supporting beams are disposed over the moon pool and the rotary table is releasably connected to them. Retractable sub-structure beams are provided below the rotary table so that means provided to move the assembled blow out preventer can move it through an opening in the derrick and over the moon pool when the rotary beams are retracted. Retractable moon pool skid beams are provided which support the blow out preventer when skidded through the moon pool opening in the substructure. In one aspect of the invention, the means connecting the rotary table to its support beams are self-aligning to that once the rotary table is aligned it can be removed and replaced without any further alignment. Also, support shoulders are provided on the main blow out preventer and lower riser section thereof which engage and are supported by the moon pool beams, so that the rotary support beams, rotary table and sub-structure support beams can be replaced and the blow out preventer hooked up to the riser, drill string or casing, the moon pool beams retracted and the blow out preventer lowered in the moon pool to the sea floor.

Guinn, D.C.; Haggard, A.K.; Thomas, J.P.

1980-10-28T23:59:59.000Z

425

Natural Gas - U.S. Energy Information Administration (EIA) - U.S. Energy  

Gasoline and Diesel Fuel Update (EIA)

30, 2012 | Release Date: May 31, 30, 2012 | Release Date: May 31, 2012 | Next Release: June 7, 2012 Previous Issues Week: 12/29/2013 (View Archive) JUMP TO: In The News | Overview | Prices/Demand/Supply | Storage In the News: Natural Gas Rigs Decline in Key Areas Active natural gas rotary rigs currently total 594, according to the latest weekly data released by Baker Hughes Incorporated. According to Baker Hughes data, natural gas-directed horizontal rigs have driven the decline in total natural gas rigs over the past several months. Horizontal-directed natural gas rig counts have fallen to 411, from levels in the low-600s a year ago. Declines have occurred in key areas of dry shale gas production, particularly in Louisiana, where the Haynesville Shale is located. The number of horizontal natural gas rigs drilling in Louisiana has fallen from

426

1Q CY2012 (PDF), Facility Representative Program Performance Indicators  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1Q CY2012 (PDF), Facility Representative Program Performance 1Q CY2012 (PDF), Facility Representative Program Performance Indicators Quarterly Report 1Q CY2012 (PDF), Facility Representative Program Performance Indicators Quarterly Report This memorandum summarizes the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period from January through March 2012. Data for these indicators were gathered by Field elements per Department of Energy (DOE) Technical Standarf 1063-2011, Facility Representatives, and reported to Headquarters program offices for evaluation and feedback to improve the FR Program. Facility Representative Program Performance Indicators for January-March 2012 More Documents & Publications 1Q CY2011 (PDF), Facility Representative Program Performance Indicators

427

3Q CY2011 (PDF), Facility Representative Program Performance Indicators  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3Q CY2011 (PDF), Facility Representative Program Performance 3Q CY2011 (PDF), Facility Representative Program Performance Indicators Quarterly Report 3Q CY2011 (PDF), Facility Representative Program Performance Indicators Quarterly Report This memorandum summarizes the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the Period July through September 2011. Data for these indicators were gathered by Field Elements per Department of Energy's (DOE) Technical Standard (STD) 1063-2011, Facility Representatives, and reported to Headquarters Program Offices for evaluation and feedback to improve the FR Program. Facility Representative Program Performance Indicators for July - September 2011 More Documents & Publications 3Q CY2010 (PDF), Facility Representative Program Performance Indicators

428

Climate Analysis Indicators Tool (CAIT) | Open Energy Information  

Open Energy Info (EERE)

Climate Analysis Indicators Tool (CAIT) Climate Analysis Indicators Tool (CAIT) (Redirected from Climate Analysis Indicators Tool) Jump to: navigation, search Tool Summary LAUNCH TOOL Name: WRI Climate Analysis Indicators Tool Agency/Company /Organization: World Resources Institute Sector: Climate, Energy, Land Topics: GHG inventory Resource Type: Dataset, Software/modeling tools User Interface: Website Website: cait.wri.org/ Language: English WRI Climate Analysis Indicators Tool Screenshot References: Climate Analysis Indicators Tool[1] CAIT is the Climate Analysis Indicators Tool -- an information and analysis tool on global climate change. It provides a comprehensive and comparable database of greenhouse gas emissions data (including all major sources and sinks) and other climate-relevant indicators. CAIT can be used to analyze a

429

Identification of performance indicators for nuclear power plants  

E-Print Network (OSTI)

Performance indicators have been assuming an increasingly important role in the nuclear industry. An integrated methodology is proposed in this research for the identification and validation of performance indicators for ...

Sui, Yu, 1973-

2001-01-01T23:59:59.000Z

430

Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator May 2011 Institute for Economic and Environmental Studies (IEES), Califo  

E-Print Network (OSTI)

). Figure 1 Southern California and US Leading Indicators U.S. economic activity, often measured by real GDP California (Figure 2). Figure 2 Leading Indicators and Real GDP 60 70 80 90 100 110 120 91.3 92.2 93.1 93 one to two quarters before SC employment changes (Figure 4). The SC indicator currently projects

de Lijser, Peter

431

2Q CY2006 (PDF), Facility Representative Program Performance Indicators  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2Q CY2006 (PDF), Facility Representative Program Performance 2Q CY2006 (PDF), Facility Representative Program Performance Indicators Quarterly Report 2Q CY2006 (PDF), Facility Representative Program Performance Indicators Quarterly Report Attached is the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period from April to June 2006. Data for these indicators are gathered by Field elements quarterly per DOE-STD-1063-2000, Facility Representatives and reported to Headquarters program offices for evaluation and feedback to improve the FR program. 2Q CY2006, Facility Representative Program Performance Indicators More Documents & Publications 3Q CY2005 (PDF), Facility Representative Program Performance Indicators Quarterly Report 4Q CY2004 (PDF), Facility Representative Program Performance Indicators

432

Climate Analysis Indicators Tool (CAIT) | Open Energy Information  

Open Energy Info (EERE)

Climate Analysis Indicators Tool (CAIT) Climate Analysis Indicators Tool (CAIT) Jump to: navigation, search Tool Summary Name: WRI Climate Analysis Indicators Tool Agency/Company /Organization: World Resources Institute Sector: Climate, Energy, Land Topics: GHG inventory Resource Type: Dataset, Software/modeling tools User Interface: Website Website: cait.wri.org/ Language: English WRI Climate Analysis Indicators Tool Screenshot References: Climate Analysis Indicators Tool[1] CAIT is the Climate Analysis Indicators Tool -- an information and analysis tool on global climate change. It provides a comprehensive and comparable database of greenhouse gas emissions data (including all major sources and sinks) and other climate-relevant indicators. CAIT can be used to analyze a wide range of climate-related data questions and to help support future

433

Key Science and Engineering Indicators: Digest 2012 | Data.gov  

NLE Websites -- All DOE Office Websites (Extended Search)

Key Science and Engineering Indicators: Digest 2012 Key Science and Engineering Indicators: Digest 2012 BusinessUSA Data/Tools Apps Challenges Let's Talk BusinessUSA You are here Data.gov » Communities » BusinessUSA » Data Key Science and Engineering Indicators: Digest 2012 Dataset Summary Description This 2012 digest of key S&E indicators is an interactive tool that draws from the National Science Board's (NSB's) Science and Engineering Indicators report. The digest serves to draw attention to important trends and data points from across Indicators and to introduce readers to the data resources available in the report. Tags {science,engineering,indicators,statistics,nsf,nsb,srs,federal,government,education,labor,employment,workforce,research,development,industry,international,global,r&d,technology,patents,"research citations"}

434

3Q CY2003 (PDF), Facility Representative Program Performance Indicators  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3Q CY2003 (PDF), Facility Representative Program Performance 3Q CY2003 (PDF), Facility Representative Program Performance Indicators Quarterly Report 3Q CY2003 (PDF), Facility Representative Program Performance Indicators Quarterly Report Attached is the Facility Representative Program Performance Indicators (PIs) Quarterly Report Covering the Period from July to September 2003. Data for these indicators are gathered by Field elements Quarterly per DOE-STD-1063-2000, Facility Representatives, and reported to Headquarters program offices for evaluation and feedback in order to improve the facility Representative Program. 3Q CY2003, Facility Representative Program Performance Indicators More Documents & Publications 2Q CY2003 (PDF), Facility Representative Program Performance Indicators Quarterly Report 3Q CY2005 (PDF), Facility Representative Program Performance Indicators

435

Depositonal and Paleoclimatic Evolution of the Cenozoic High Plains Succession from Core: Haskell Co., Kansas  

E-Print Network (OSTI)

, saturated, and highly heterogeneous (Frye et al., 1956; Macfarlane, 2009). To address these deficiencies, this study used mobile, platform-mounted hollow-stem auger and rotary-vibratory drill rigs to recover the first ever intact drill core of the HPS... in the High Plains aquifer in western Kansas. Methods Drilling and core retrieval were accomplished using an Acker AD-II hollow-stem auger with wireline, split spoon core sampler and S-27 rotary-vibratory drill rig. This combination was chosen to maximize...

Harlow, R. Hunter

2013-12-31T23:59:59.000Z

436

An accounting manual for oil well servicing contractors  

E-Print Network (OSTI)

, and bailing of' oil wells, These Jobs had previously been done by the oil companies them- selves, with a standard service rig set up over the well at the time of its completion. The more complicated. Jobs of deepening and work requiring rotary tools were..., with complete set of Rig 0 Lite vapox' proof wix ing, and three Hutoh- inson vapor pxoof floodlights, x One 1V" Emsco Gilbath rotary. Emsco NB?SO, enclosed, 4 sheave travel- ing block B Z. Tx'iplex hooki 60 ?on, 60 C Oilwell swivel, Two centrifugal water...

Robert, Curtis Dean

1949-01-01T23:59:59.000Z

437

Industrial experience at the Arabian American Oil Company in Saudi Arabia: an internship report  

E-Print Network (OSTI)

Limitations ....... ..46 b. Determination of Optimum Circulating Rate-.- 47 c. Determination of Pressure Available to the Bit .................................... ..50 d. Selection of Nozzle Combinations ........ .51 e. Weight on the Bit and Rotary Speed... to the operational nature of the work and partly due to the shortage of engineering manpower. As a result, the work was generally assigned on the basis of an engineer per rig(s), an engineer per field(s), or an engineer per area(s). This report, therefore...

Akkad, Ruwaid Ahmed, 1943-

2013-03-13T23:59:59.000Z

438

1Q CY2010 (PDF), Facility Representative Program Performance Indicators  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1Q CY2010 (PDF), Facility Representative Program Performance 1Q CY2010 (PDF), Facility Representative Program Performance Indicators Quarterly Report 1Q CY2010 (PDF), Facility Representative Program Performance Indicators Quarterly Report "Attached is the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period from January to March2010. Data for these indicators are gathered by Field elements quarterly per DOE-STD- 1063-2006, Facility Representatives, and reported to Headquarters program offices for evaluation and feedback to improve the FR Program. Highlights from this report are presented below." 1Q CY2010, Facility Representative Program Performance Indicators More Documents & Publications 1Q CY2011 (PDF), Facility Representative Program Performance Indicators

439

3Q CY2010 (PDF), Facility Representative Program Performance Indicators  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3Q CY2010 (PDF), Facility Representative Program Performance 3Q CY2010 (PDF), Facility Representative Program Performance Indicators Quarterly Report 3Q CY2010 (PDF), Facility Representative Program Performance Indicators Quarterly Report This memorandum summarizes the highlights of the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period of July through September 2010. Data for these indicators are gathered by Field elements quarterly per Department of Energy (DOE) Standard (STD)-1063-2006, Facility Representative and reported to Headquarters program offices for evaluation and feedback to improve the FR Program. Facility Representative Program Performance Indicators for July - September 2010 More Documents & Publications 3Q CY2011 (PDF), Facility Representative Program Performance Indicators

440

3Q CY2007 (PDF), Facility Representative Program Performance Indicators  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3Q CY2007 (PDF), Facility Representative Program Performance 3Q CY2007 (PDF), Facility Representative Program Performance Indicators Quarterly Report 3Q CY2007 (PDF), Facility Representative Program Performance Indicators Quarterly Report Attached is the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period from July to September 2007. Data for these indicators are gathered by Field elements quarterly per Department of Energy (DOE-STD-1063-2006, Facility Representatives, and reported to Headquarters program offices for evaluation and feedback to improve the FR program. A summary of this quarter 's data concluded: 3Q CY2007, Facility Representative Program Performance Indicators More Documents & Publications 2Q CY2009 (PDF), Facility Representative Program Performance Indicators

Note: This page contains sample records for the topic "indicators rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Climate Analysis Indicators Tool (CAIT) | Open Energy Information  

Open Energy Info (EERE)

form form View source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit with form History Facebook icon Twitter icon » Climate Analysis Indicators Tool (CAIT) (Redirected from WRI Climate Analysis Indicators Tool) Jump to: navigation, search Tool Summary LAUNCH TOOL Name: WRI Climate Analysis Indicators Tool Agency/Company /Organization: World Resources Institute Sector: Climate, Energy, Land Topics: GHG inventory Resource Type: Dataset, Software/modeling tools User Interface: Website Website: cait.wri.org/ Language: English WRI Climate Analysis Indicators Tool Screenshot References: Climate Analysis Indicators Tool[1] CAIT is the Climate Analysis Indicators Tool -- an information and analysis

442

Policy Applications of Energy Indicators | Open Energy Information  

Open Energy Info (EERE)

Policy Applications of Energy Indicators Policy Applications of Energy Indicators Jump to: navigation, search Tool Summary Name: Policy Applications of Energy Indicators Agency/Company /Organization: International Atomic Energy Agency Sector: Energy Topics: Co-benefits assessment, Policies/deployment programs Resource Type: Publications Website: www.blackwell-synergy.com/toc/narf/29/4 References: Policy Applications of Energy Indicators[1] "In November 2005, a special issue of the Natural Resources Forum was published on 'Policy Applications of Energy Indicators' based on the ISED programme. To read the full issue, click here. The special issue features articles highlighting how energy indicators were developed, refined and tested by international and regional agencies and national experts to

443

1Q CY2011 (PDF), Facility Representative Program Performance Indicators  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1Q CY2011 (PDF), Facility Representative Program Performance 1Q CY2011 (PDF), Facility Representative Program Performance Indicators Quarterly Report 1Q CY2011 (PDF), Facility Representative Program Performance Indicators Quarterly Report This memorandum summarizes the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the Period January through March 2011. Data for these indicators were gathered by Field Elements per Department of Energy's (DOE) Technical Standard (STD) 1063-2011, Facility Representatives, and reported to Headquarters Program Offices for evaluation and feedback to improve the FR Program. This report reflects changes in DOE STD 1063-2011 that deleted one indicator and changed the way two others are calculated. The changes are discussed below. Facility Representative Program Performance Indicators for January - March

444

3Q CY2006 (PDF), Facility Representative Program Performance Indicators  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3Q CY2006 (PDF), Facility Representative Program Performance 3Q CY2006 (PDF), Facility Representative Program Performance Indicators Quarterly Report 3Q CY2006 (PDF), Facility Representative Program Performance Indicators Quarterly Report Attached is the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period from July to September 2006. Data for these indicators are gathered by Field elements quarterly per DOE-STD-1063-2000, Facility Representatives and reported to Headquarters program offices for evaluation and feedback to improve the FR program. A summary of this quarters data concluded: 76% fully qualified 41% staffing level

445

2Q CY2007 (PDF), Facility Representative Program Performance Indicators  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2Q CY2007 (PDF), Facility Representative Program Performance 2Q CY2007 (PDF), Facility Representative Program Performance Indicators Quarterly Report 2Q CY2007 (PDF), Facility Representative Program Performance Indicators Quarterly Report Attached is the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period from April to June 2007. Data for these indicators are gathered by field elements quarterly per DOE-STD-1063-2006, Facility Representatives, and reported to Headquarters program offices for evaluation and feedback to impove the FR Program. A summary of this quarter's data concluded: 74% Fully Qualified 94% Staffing Level ( last quarter was

446

4Q CY2006 (PDF), Facility Representative Program Performance Indicators  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4Q CY2006 (PDF), Facility Representative Program Performance 4Q CY2006 (PDF), Facility Representative Program Performance Indicators Quarterly Report 4Q CY2006 (PDF), Facility Representative Program Performance Indicators Quarterly Report Attached is the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period from October to December 2006. Data for these indicators are gathered by Field elements quarterly per DOE-STD-1063-2000, Facility Representatives and reported to Headquarters program offices for evaluation and feedback to improve the FR program. A summary of this quarters data concluded: 72% Fully Qualified ( last Quarter was

447

2Q CY2008 (PDF), Facility Representative Program Performance Indicators  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2Q CY2008 (PDF), Facility Representative Program Performance 2Q CY2008 (PDF), Facility Representative Program Performance Indicators Quarterly Report 2Q CY2008 (PDF), Facility Representative Program Performance Indicators Quarterly Report Attached is the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period from April to June 2008. Data for these indicators are gathered by Field elements quarterly per DOE-STD- 1063-2006, Facility Representatives, and reported to Headquarters program offices for evaluation and feedback to improve the FR Program. A summary of this quarter's data concluded: 87% Fully Qualifed ( last quarter was 85%) 86% Staffing Level ( last quarter was 88%)

448

Sustainability Indicators for Discrete Manufacturing Processes Applied to Grinding Technology  

E-Print Network (OSTI)

from all three pillars of sustainability: environmental,1, 2]. Sustainability encompasses the three pillars ofinto three sustainability indicators for each pillar and/or

Linke, Barbara S.; Corman, Gero J.; Dornfeld, David A.; Tönissen, Stefan

2013-01-01T23:59:59.000Z

449

Sustainability Indicators for Discrete Manufacturing Processes Applied to Grinding Technology  

E-Print Network (OSTI)

study, the indicator “Energy intensity” measures the energylabor intensity, energy intensity, water intensity, andand we consider the energy intensity. Number, Weight, or

Linke, Barbara S.; Corman, Gero J.; Dornfeld, David A.; Tönissen, Stefan

2013-01-01T23:59:59.000Z

450

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

8 8 HOISTS 8-i Chapter 8 Hoists This chapter provides safety standards for inspecting, testing, and operating hoists not permanently mounted on overhead cranes and implements the requirements of ASME B30.11 ("Monorail Systems and Underhung Cranes"), B30.16["Overhead Hoists (Underhung)"], and B30.21 ("Manually Lever Operated Hoists"). 8.1 GENERAL .................................................................................................................................8-1 8.1.1 Operator Training/Qualification ..................................................................................8-4 8.1.2 Marking........................................................................................................................8-4

451

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

6 6 PERSONNEL QUALIFICATION AND TRAINING 6-i Chapter 6 Personnel Qualification and Training This chapter describes personnel qualification and training. Only qualified personnel shall operate the equipment covered in this standard. 6.1 GENERAL ................................................................................................................................6-1 6.2 QUALIFICATION...................................................................................................................6-2 6.2.1 General.........................................................................................................................6-2 6.2.2 Operators of Cab-Operated and Pulpit-Operated Cranes .............................................6-2

452

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

0 0 FORKLIFT TRUCKS 10-i Chapter 10 Forklift Trucks This chapter specifies operation, inspection, testing, and maintenance requirements for forklift trucks powered by internal-combustion engines or electric motors and implements the requirements of ASME B56.1 ("Safety Standard for powered Industrial Trucks - Low Lift and High lift Trucks") and B56.6 ("Rough Terrain Fork Lift Trucks"), and ANSI/UL 558 ("Internal-Combustion-Engine-Powered Industrial Trucks") and 583 ("Electric-Battery-Powered Industrial Trucks"). 10.1 GENERAL ...............................................................................................................................10-1 10.1.1 Operator Training/Qualification ................................................................................10-1

453

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

019-2004 019-2004 CHAPTER 16 MISCELLANEOUS LIFTING DEVICES 16-i Chapter 16 Miscellaneous Lifting Devices This chapter provides safety standards designated to sign verify, based on personal observations, certified records, or direct reports, that a specific action has been performed in accordance with specified requirements. For the operation, inspection, testing, and maintenance for miscellaneous lifting devices, (truck mounted cranes - capacity 1 ton or less not covered in ASME B30.5 ("Mobile and Locomotive Cranes") and implements the requirements of ASME PALD ("Portable Automotive Lifting Devices") for self contained shop cranes. 16.1 GENERAL ..................................................................................................................................

454

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

7 7 OVERHEAD AND GANTRY CRANES 7-i Chapter 7 Overhead and Gantry Cranes This chapter specifies operation, inspection, maintenance, and testing requirements for the use of overhead and gantry cranes and implements the requirements of ASME B30.2 ["Overhead and Gantry Cranes (Top- Running Bridge, Single or Multiple Girder, Top-Running Trolley Hoist)"], B30.11 ("Monorail Systems and Underhung Cranes"), and B30.17 ["Overhead and Gantry Cranes (Top-Running Bridge, Single Girder, Underhung Hoist")]. Only equipment built to the appropriate design standards shall be used in DOE installations. 7.1 GENERAL .................................................................................................................................7-1

455

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

6 6 PERSONNEL QUALIFICATION AND TRAINING 6-i Chapter 6 Personnel Qualification and Training This chapter describes personnel qualification and training. Only qualified personnel shall operate the equipment covered in this standard. 6.1 GENERAL................................................................................................................................6-1 6.2 QUALIFICATION...................................................................................................................6-2 6.2.1 General.........................................................................................................................6-2 6.2.2 Operators of Cap-Operated and Pulpit-Operated Cranes .............................................6-2

456

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DEFINITIONS DEFINITIONS ................................................. 1-1 CHAPTER 2 CRITICAL LIFTS................................................................................. 2-1 2.1 CRITICAL-LIFT DETERMINATION........................................................ 2-1 2.2 CRITIAL-LIFT REQUIREMENTS............................................................. 2-2 CHAPTER 3 PREENGINEERED PRODUCTION LIFTS................................3-1 3.1 GENERAL....................................................................................................... 3-1 3.2 OPERATION EVALUATION ...................................................................... 3-2 3.2.1 Load Identification................................................................................

457

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

0 0 FORKLIFT TRUCKS 10-i This chapter specifies operation, inspection, testing, and maintenance requirements for forklift trucks powered by internal-combustion engines or electric motors and implements the requirements of ANSI/ITSDF B56.1 ("Safety Standard for powered Industrial Trucks - Low Lift and High lift Trucks") and ANSI/ITSDF B56.6 ("Rough Terrain Fork Lift Trucks"), and ANSI/UL 558 ("Internal-Combustion- Engine-Powered Industrial Trucks") and ANSI/UL 583 ("Electric-Battery-Powered Industrial Trucks"). 10.1 GENERAL ...............................................................................................................................10-1 10.1.1 Operator Training/Qualification ................................................................................10-1

458

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3 3 PREENGINEERED PRODUCTION LIFTS 3-i Chapter 3 Preengineered Production Lifts This chapter provides requirements for the design, evaluation, and performance of preengineered production lifts. This lift designation may be used at the discretion of the contractor for selected operations. 3.1 GENERAL................................................................................................................................3-1 3.2 OPERATION EVALUATION................................................................................................3-2 3.2.1 Load Identification.......................................................................................................3-2 3.2.2 Task Determination......................................................................................................3-2

459

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

7 7 REFERENCES 17-1 Chapter 17 References American Institute of Steel Construction AISC Specifications for the design, fabrication, and erection of structural steel for buildings. American Iron and Steel Institute AISI Standards for Type-302 or Type-304 stainless steel. American National Standards Institute and the American Society of Mechanical Engineers ANSI A10.28, Work Platforms Suspended From Cranes or Derricks. ANSI A10.18, Floor and Wall Openings, Railings and Toe Boards. ASME B30.1, Jacks ASME B30.2, Overhead and Gantry Cranes (Top-Running Bridge, Single or Multiple Girder, Top-Running Trolley Hoist). ASME B30.5, Mobile and Locomotive Cranes. ASME B30.6, Derricks. ASME B30.7, Base-Mounted Drum Hoists. ASME B30.9, Slings.

460

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3 3 PREENGINEERED PRODUCTION LIFTS 3-i Chapter 3 Preengineered Production Lifts This chapter provides requirements for the design, evaluation, and performance of preengineered production lifts. This lift designation may be used at the discretion of the contractor for selected operations. 3.1 PREENGINEERED PRODUCTION LIFT DETERMINATION.......................................3-1 3.2 LIFTING FIXTURES..............................................................................................................3-2 3.2.1 Design ..........................................................................................................................3-2 3.2.2 Fabrication ...................................................................................................................3-2

Note: This page contains sample records for the topic "indicators rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2 2 CRITICAL LIFTS 2-i Chapter 2 Critical Lifts This chapter provides guidelines for critical-lift determination and requirements for planning and performing a critical lift safely and judiciously. 2.1 CRITICAL-LIFT DETERMINATION ................................................................ 2-1 2.2 CRITICAL-LIFT REQUIREMENTS ............................................................. 2-2 DOE-STD-1090-2007 Chapter 2 2-ii Critical Lifts INTENTIONALLY BLANK DOE-STD-1090-2007 2.1 CRITICAL-LIFT DETERMINATION 2-1 Chapter 2 Critical Lifts a. An appointed person shall classify each lift into one of the DOE categories (ordinary, critical, or preengineered production) prior to planning the lift. b. A lift shall be designated critical if any of

462

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2 2 CRITICAL LIFTS 2-i Chapter 2 Critical Lifts This chapter provides guidelines for critical-lift determination and requirements for planning and performing a critical lift safely and judiciously. 2.1 CRITICAL-LIFT DETERMINATION ................................................................ 2-1 2.2 CRITICAL-LIFT REQUIREMENTS ............................................................. 2-2 DOE-STD-1090-2004 Chapter 2 2-ii Critical Lifts INTENTIONALLY BLANK DOE-STD-1090-2004 2.1 CRITICAL-LIFT DETERMINATION 2-1 Chapter 2 Critical Lifts a. An appointed person shall classify each lift into one of the DOE categories (ordinary, critical, or preengineered production) prior to planning the lift. b. A lift shall be designated critical if any of

463

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 4 LIFTING PERSONNEL 4-i Chapter 4 Lifting Personnel This chapter describes requirements for lifting personnel. 4.1 GENERAL................................................................................................................................4-1 4.1.1 Personnel Lifting Evaluation .......................................................................................4-1 4.1.2 Designated Leader .......................................................................................................4-1 4.1.3 Trial Lift.......................................................................................................................4-2 4.1.4 Lifting Operations........................................................................................................4-2

464

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CHAPTER 17 CHAPTER 17 REFERENCES 17-1 Chapter 17 References American Institute of Steel Construction AISC Specifications for the design, fabrication, and erection of structural steel for buildings. American Iron and Steel Institute AISI Standards for Type-302 or Type-304 stainless steel. American National Standards Institute and American Society of Mechanical Engineers ANSI A10.28, Work Platforms Suspended From Cranes or Derricks. ANSI A10.18, Floor and Wall Openings, Railings and Toe Boards. ASME B30.2, Overhead and Gantry Cranes (Top-Running Bridge, Single or Multiple Girder, Top-Running Trolley Hoist). ASME B30.5, Mobile and Locomotive Cranes. ASME B30.6, Derricks. ASME B30.7, Base-Mounted Drum Hoists. ASME B30.9, Slings. ASME B30.10, Hooks.

465

RigMesh: Automatic Rigging for Part-Based Shape Modeling and Deformation Peter Borosan1  

E-Print Network (OSTI)

proficient at commercial, state-of-the-art tools such as Maya and 3ds Max [Autodesk 2012c; Autodesk 2012a

Columbia University

466

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DEFINITIONS........................................1-1 DEFINITIONS........................................1-1 CHAPTER 2 CRITICAL LIFTS .......................................................................2-1 2.1 CRITICAL-LIFT DETERMINATION........................................................ 2-1 2.2 CRITIAL-LIFT REQUIREMENTS............................................................. 2-2 CHAPTER 3 PREENGINEERED PRODUCTION LIFTS................................3-1 3.1 PRENGINEERED PRODUCTION LIFT DETERMINATION................ 3-1 3.2 LIFTING FIXTURES .................................................................................... 3-2 3.3.1 Design ................................................................................................... 3-2 3.3.2 Fabrication ............................................................................................

467

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

9 9 MOBILE CRANES 9-i Chapter 9 Mobile Cranes This chapter specifies operation, inspection, maintenance, and testing requirements for the use of mobile cranes and implements the requirements of ASME B30.5 ("Mobile and Locomotive Cranes"). Only equipment built to appropriate design standards shall be used at DOE installations. 9.1 GENERAL .................................................................................................................................9-1 9.1.1 Operator Training/Qualification ..................................................................................9-1 9.1.2 Load Limits..................................................................................................................9-1 9.1.3 Load Rating Chart........................................................................................................9-1

468

Microsoft Word - DOE Subject Area Indic#2C05.doc  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Subject Subject Area Indicators and Key Word List for Restricted Data and Formerly Restricted Data July 2005 Subject Area Indicators and Key Word List 1 TABLE OF CONTENTS Purpose ...................................................................................................................................... 2 Background................................................................................................................................. 3 Difference Between Restricted Data (RD) and Formerly Restricted Data (FRD) and National Security Information (NSI) ........................................................................................ 4 Access to RD and FRD ...............................................................................................................

469

MARKET SHARE INDICATES QUALITY AMIR BAN AND NATI LINIAL  

E-Print Network (OSTI)

MARKET SHARE INDICATES QUALITY AMIR BAN AND NATI LINIAL Abstract. Market share and quality to the effect that higher market share indicates higher quality. Indeed, such an inference would need detailed quality. We investigate a model where customers are informed about their history with products and about

Linial, Nathan "Nati"

470

Short Communication Three ocean state indices implemented in  

E-Print Network (OSTI)

, and currents at various resolutions. We briefly present the OFS, then describe three currently available oceanShort Communication Three ocean state indices implemented in the Mercator-Ocean operational suite L., and Soulat, F. 2008. Three ocean state indices implemented in the Mercator-Ocean operational suite. ­ ICES

Ribes, Aurélien

471

Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator May 2014 Center for Economic Analysis and Forecasting (CEAF), California  

E-Print Network (OSTI)

measured by real GDP growth, is expected to increase in the next three to six months, given the increase activity in Southern California (Figure 2). Figure 2 Leading Indicators and Real GDP -4.0 -2.0 0.0 2.0 4 employment changes (Figure 4). The SC indicator currently projects an increase in Southern California

de Lijser, Peter

472

Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator November 2013 Center for Economic Analysis and Forecasting (CEAF), Calif  

E-Print Network (OSTI)

measured by real GDP growth, is expected to increase in the next three to six months, given the increase activity in Southern California (Figure 2). Figure 2 Leading Indicators and Real GDP -4.0 -2.0 0.0 2.0 4 employment changes (Figure 4). The SC indicator currently projects an increase in Southern California

de Lijser, Peter

473

Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator November 2011 Institute for Economic and Environmental Studies (IEES), C  

E-Print Network (OSTI)

by real GDP growth, is expected to increase in the next three to six months, given the increase in the U in Southern California (Figure 2). Figure 2 Leading Indicators and Real GDP 60 70 80 90 100 110 120 91.3 92 (Figure 4). The SC indicator currently projects an increase in Southern California economic activity

de Lijser, Peter

474

Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator August 2011 Institute for Economic and Environmental Studies (IEES), Cal  

E-Print Network (OSTI)

by real GDP growth, is expected to increase in the next three to six months, given the increase in the U in Southern California (Figure 2). Figure 2 Leading Indicators and Real GDP 60 70 80 90 100 110 120 91.3 92 (Figure 4). The SC indicator currently projects an increase in Southern California economic activity

de Lijser, Peter

475

Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator February 2014 Center for Economic Analysis and Forecasting (CEAF), Calif  

E-Print Network (OSTI)

measured by real GDP growth, is expected to increase in the next three to six months, given the increase activity in Southern California (Figure 2). Figure 2 Leading Indicators and Real GDP -4.0 -2.0 0.0 2.0 4 employment changes (Figure 4). The SC indicator currently projects an increase in Southern California

de Lijser, Peter

476

Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator August 2014 Center for Economic Analysis and Forecasting (CEAF), Califor  

E-Print Network (OSTI)

activity, often measured by real GDP growth, is expected to increase in the next three to six months, given activity in Southern California (Figure 2). Figure 2 Leading Indicators and Real GDP 60 70 80 90 100 110 employment changes (Figure 4). The SC indicator currently projects an increase in Southern California

de Lijser, Peter

477

METROPOLITAN REPORT Economic Indicators for the New Orleans Area  

E-Print Network (OSTI)

METROPOLITAN REPORT Economic Indicators for the New Orleans Area Division of Business and Economic · The New Orleans metropolitan area has achieved significant recovery during the past five years. Despite%, respectively). Residential construction has slowed and is one of the lowest ranking indicators at 51% of pre

Kulp, Mark

478

Surface Indicators of Geothermal Activity at Salt Wells, Nevada, USA,  

Open Energy Info (EERE)

Surface Indicators of Geothermal Activity at Salt Wells, Nevada, USA, Surface Indicators of Geothermal Activity at Salt Wells, Nevada, USA, Including Warm Ground, Borate Deposits, and Siliceous Alteration Jump to: navigation, search OpenEI Reference LibraryAdd to library Conference Paper: Surface Indicators of Geothermal Activity at Salt Wells, Nevada, USA, Including Warm Ground, Borate Deposits, and Siliceous Alteration Abstract Surface indicators of geothermal activity are often present above blind or concealed geothermal systems in the Great Basin, but their expressions are sometimes subtle. When mapped in detail, these indicators yield valuable information on the location, structural controls, and potential subsurface reservoir temperatures of geothermal fluids. An example is provided by the Salt Wells geothermal system in Churchill County, Nevada, USA, where

479

1Q CY2000 (PDF), Facility Representative Program Performance Indicators  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1Q CY2000 (PDF), Facility Representative Program Performance 1Q CY2000 (PDF), Facility Representative Program Performance Indicators Quarterly Report 1Q CY2000 (PDF), Facility Representative Program Performance Indicators Quarterly Report "The Facility Representative Program Performance Indicators (PIs) Quarterly Report is attached, covering the period from January 2000 to March 2000. Data for these indicators are gathered by the Field elements quarterly per the Facility Representatives Standard, DOE-STD-1 063, and reported to Headquarters Program Offices for evaluation and feedback in order to improve the Facility Representative Program. The definitions of the PIs from the Standard are also attached for your use in evaluating the data." 1Q CY2000, Facility Representative Program Performance Indicators

480

4Q CY2001 (PDF), Facility Representative Program Performance Indicators  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4Q CY2001 (PDF), Facility Representative Program Performance 4Q CY2001 (PDF), Facility Representative Program Performance Indicators Quarterly Report 4Q CY2001 (PDF), Facility Representative Program Performance Indicators Quarterly Report The Facility Representive Program Performance Indicators (PIs) Quarterly Report is attached covering the period from October to December 2001. Data for these indicators are gathered by the Field elements quarterly per the Facility Representatives Standards , DOE-STD-1063, and reported to Headquarters Program Offices for evaluation and feedback in order to improve the Facility Representative Program. The definition of the PIs from the Standard are also attached for your use in evaluating the data 4Q CY2001, Facility Representative Program Performance Indicators More Documents & Publications

Note: This page contains sample records for the topic "indicators rotary rigs" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

2Q CY2005 (PDF), Facility Representative Program Performance Indicators  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2Q CY2005 (PDF), Facility Representative Program Performance 2Q CY2005 (PDF), Facility Representative Program Performance Indicators Quarterly Report 2Q CY2005 (PDF), Facility Representative Program Performance Indicators Quarterly Report Attached is the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period from April to June 2005. Data for these indicators are gathered by Field elements quarterly per DOE-STD-1063-2000, Facility Representatives, and reported to Headquarters program offices for evaluation and feedback to improve the FR Program. As of June 30,2005, 97% of all FRs were fully qualified, down from 88% the previous quarter, but exceeding the DOE goal of 80%. Eighteen of 27 reporting sites meet the goal of FR qualifications. 2Q CY2005, Facility Representative Program Performance Indicators

482

EIA Data: 2011 United States Residential Sector Key Indicators and  

Open Energy Info (EERE)

Residential Sector Key Indicators and Residential Sector Key Indicators and Consumption Dataset Summary Description This dataset is the 2011 United States Residential Sector Key Indicators and Consumption, part of the Annual Energy Outlook that highlights changes in the AEO Reference case projections for key energy topics. Source EIA Date Released December 16th, 2010 (4 years ago) Date Updated Unknown Keywords consumption EIA energy residential sector key indicators Data application/vnd.ms-excel icon Residential Sector Key Indicators and Consumption (xls, 62.5 KiB) Quality Metrics Level of Review Peer Reviewed Comment Temporal and Spatial Coverage Frequency Annually Time Period License License Open Data Commons Public Domain Dedication and Licence (PDDL) Comment http://www.eia.gov/abouteia/copyrights_reuse.cfm

483

Indicators for resources and resource-efficiency: a Danish perspective  

Science Journals Connector (OSTI)

The specific material flows and use of energy and land, which cause severe environmental and health problems in Denmark, are delimited by a risk assessment. Resource-efficiency is defined in terms of material flows and is estimated to be 0.07 without unused flows and 0.04 with unused flows for Denmark, 1990. It is shown that the path to both a global sustainable environment and welfare goes through increasing resource-efficiency, increasing lifetime of products, detoxification, dematerialisation of welfare and increasing quality and quantity of ecosystems. An indicator system for Denmark consisting of a pyramid structured by formal indicators is proposed. At the top of the indicator pyramid are indicators for aggregated material and energy flows, almost unaffected nature and the flows of dangerous substances. The formal indicators represent flows of resources and emissions, resources and emissions related to ecological space, economic turnover and number of inhabitants as well as resource efficiency, lifetime of materials and material welfare.

Karsten Krogh Andersen

2003-01-01T23:59:59.000Z

484

Environmental indicators for sustainable production of algal biofuels  

Science Journals Connector (OSTI)

Abstract For analyzing sustainability of algal biofuels, we identify 16 environmental indicators that fall into six categories: soil quality, water quality and quantity, air quality, greenhouse gas emissions, biodiversity, and productivity. Indicators are selected to be practical, widely applicable, predictable in response, anticipatory of future changes, independent of scale, and responsive to management. Major differences between algae and terrestrial plant feedstocks, as well as their supply chains for biofuel, are highlighted, for they influence the choice of appropriate sustainability indicators. Algae strain selection characteristics do not generally affect which indicators are selected. The use of water instead of soil as the growth medium for algae determines the higher priority of water- over soil-related indicators. The proposed set of environmental indicators provides an initial checklist for measures of algal biofuel sustainability but may need to be modified for particular contexts depending on data availability, goals of stakeholders, and financial constraints. Use of these indicators entails defining sustainability goals and targets in relation to stakeholder values in a particular context and can lead to improved management practices.

Rebecca A. Efroymson; Virginia H. Dale

2015-01-01T23:59:59.000Z

485

Environmental indicators for sustainable production of algal biofuels  

SciTech Connect

For analyzing sustainability of algal biofuels, we identify 16 environmental indicators that fall into six categories: soil quality, water quality and quantity, air quality, greenhouse gas emissions, biodiversity, and productivity. Indicators are selected to be practical, widely applicable, predictable in response, anticipatory of future changes, independent of scale, and responsive to management. Major differences between algae and terrestrial plant feedstocks, as well as their supply chains for biofuel, are highlighted, for they influence the choice of appropriate sustainability indicators. Algae strain selection characteristics do not generally affect which indicators are selected. The use of water instead of soil as the growth medium for algae determines the higher priority of water- over soil-related indicators. The proposed set of environmental indicators provides an initial checklist for measures of biofuel sustainability but may need to be modified for particular contexts depending on data availability, goals of the stakeholders, and financial constraints. Use of these indicators entails defining sustainability goals and targets in relation to stakeholder values in a particular context and can lead to improved management practices.

Efroymson, Rebecca Ann [ORNL; Dale, Virginia H [ORNL

2014-01-01T23:59:59.000Z

486

Facility Representative Program Performance Indicators for October - December 2010  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

FOR DISTRIBUTION FOR DISTRIBUTION FROM: ANDREW C. LAWRENCE DIRECTOR OFFICE OF NUCLEAR SAFETY, QUALITY ASSURANCE AND ENVIRONMENT OFFICE OF HEALTH, SAFETY AND SECURITY SUBJECT: Facility Representative Program Performance Indicators Quarterly Report, October-December (Fourth Quarter Calendar Year 2010) This memorandum summarizes the highlights of the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period October through December 2010. Data for these indicators were gathered by Field Elements quarterly per Department of Energy (DOE) Standard (STD)-1063-2006, Facility Representatives, and reported to Headquarters Program Offices for evaluation and feedback to improve the FR Program. Highlights from this report are presented below:

487

A New Collaborative Tool for Visually Understanding National Health Indicators  

SciTech Connect

The authors propose a new online collaborative tool for visually understanding national health indicators, which facilitates the full spectrum of investigation of indicators, from an overview of all the correlation coefficients between variables, to investigation of subsets of selected variables, and to individual data element analysis. this tool is publicly accessible at http://cda.ornl.gov/heat/heatmap.html. In this paper, they discuss the key issues regarding the interface design and implementation. They also illustrate how to use their interface for analyzing the health indicator dataset by showing some key system views. In the end, they introduce and discuss some ongoing research efforts extending this work.

Xu, Songhua [ORNL; Jewell, Brian C [ORNL; Steed, Chad A [ORNL; Schryver, Jack C [ORNL

2012-01-01T23:59:59.000Z

488

Southern California Leading EconomicSouthern California Leading EconomicSouthern California Leading EconomicSouthern California Leading Economic IndicatorIndicatorIndicatorIndicator November 2012 Institute for Economic and Environmental Studies (IEES), C  

E-Print Network (OSTI)

Indicator U.S. economic activity, often measured by real GDP growth, is expected to increase in the next Indicators and Real GDP -10.0 -8.0 -6.0 -4.0 -2.0 0.0 2.0 4.0 6.0 08.3 08.4 09.1 09.2 09.3 09.4 10.1 10.2 10 (Figure 4). The SC indicator currently projects an increase in Southern California economic activity

de Lijser, Peter

489

Common Myths about Tamper Indicating Seals - Vulnerability Assessment Team  

NLE Websites -- All DOE Office Websites (Extended Search)

Common Myths about Tamper Common Myths about Tamper Indicating Seals VAT Projects Introducing the VAT Adversarial Vulnerability Assessments Safety Tags & Product Counterfeiting Election Security Spoofing GPS Defeating Existing Tamper-Indicating Seals Specialty Field Tools & Sampling Tools Insider Threat Mitigation Drug Testing Security Microprocessor Prototypes The Journal of Physical Security Vulnerability Assessments Vulnerability Assessments Insanely Fast µProcessor Shop Insanely Fast µProcessor Shop Seals About Seals Applications of Seals Common Myths about Tamper Indicating Seals Definitions Findings and Lessons Learned New Seals Types of Seals Seals References Selected VAT Papers Selected VAT Papers Selected Invited Talks Self-Assessment Survey Security Maxims Devil's Dictionary of Security Terms

490

Spreader beam design adds safety to BOP moves  

SciTech Connect

A well-designed spreader beam can maneuver a blowout preventer (BOP) stack more safely and easily a below the rig floor. This is true for both a below the rig-floor crane, or a through the rotary table lift. The use of a spreader beam allows for direct vertical lifts, better lifting points, and elimination of multiple sling-cable wraps. This paper shows the simple spreader-beam lifting configuration. The design is for a spreader beam to lift a 60-ton BOP stack, utilizing available materials on an offshore arctic drilling rig. The design presented avoids complicated fabrication techniques.

Vargas, K.J. (Gulf Canada Resources Ltd., Calgary (Canada))

1989-12-01T23:59:59.000Z

491

Development and assessment of electronic manual for well control and blowout containment  

E-Print Network (OSTI)

Fig. 1.4 ? Spindletop Lucas well blowout (1901) 17 As the rotary rig took over for the cable tool rig, and the depth of the wells kept getting deeper, there was a need to control the higher pressures encountered. The developments... this is not achieved, there might be an unscheduled inflow of fluids into the well. Most commonly, the occurrence of a kick is due to the rig crew not doing their job of managing the well pressures adequately. With the event of a kick follows the need...

Grottheim, Odd Eirik

2005-11-01T23:59:59.000Z

492

Slim Holes At Alvord Hot Springs Area (Combs, Et Al., 1999) | Open Energy  

Open Energy Info (EERE)

Combs, Et Al., 1999) Combs, Et Al., 1999) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Slim Holes At Alvord Hot Springs Area (Combs, Et Al., 1999) Exploration Activity Details Location Alvord Hot Springs Area Exploration Technique Slim Holes Activity Date Usefulness not indicated DOE-funding Unknown Notes Anadarko Petroleum Corporation drilled two slimhole discoveries in the 1980s, one at Salt Wells, NV, and the other at Pueblo Valley, OR. Both of these slimholes were hot enough to discharge unassisted and were successfully flow tested. A slimhole at Pueblo Valley, in south-east Oregon was planned and permitted as a test well to evaluate an interval of fractured basalt which had been discovered while drilling an earlier thermal-gradient hole. Using a UDR1500 rig, the hole was rotary-drilled to

493

4Q CY2011 (PDF), Facility Representative Program Performance Indicators  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4Q CY2011 (PDF), Facility Representative Program Performance 4Q CY2011 (PDF), Facility Representative Program Performance Indicators Quarterly Report 4Q CY2011 (PDF), Facility Representative Program Performance Indicators Quarterly Report "This memorandum summarizes the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period from October through December 2011. Data for these indicators were gathered by field elements per Department of Energy (DOE) Technical Standard 1063-2011 , Facility Representatives, and reported to Headquarters program offices for evaluation and feedback to improve the FR Program. Highlights from this report include: FR Staffing/Qualification/Oversight Data: * DOE was staffed at 179 FR Full Time Equivalents (FTE), which is 92 percent of the full staffing level (DOE goal is 100 percent). Four FRs left due to transfer,

494

4Q CY2007 (PDF), Facility Representative Program Performance Indicators  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4Q CY2007 (PDF), Facility Representative Program Performance 4Q CY2007 (PDF), Facility Representative Program Performance Indicators Quarterly Report 4Q CY2007 (PDF), Facility Representative Program Performance Indicators Quarterly Report "Attached is the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period from October to December 2007. Data for these indicators are gathered by Field elements quarterly per DOE-STD- 1063-2006, Facility Representatives, and reported to Headquarters program offices for evaluation and feedback to improve the FR Program. A summary of this quarter's data concluded: 83% Fully Qualified (last Quarter was 82%) 85% Staffing Level (last Quarter was 93%) 45% Time Spent in the Field (DOE goal is >40%) 73% Time Spent in Oversight Activities (DOE Goal is> 65%)"

495

2Q CY2003 (PDF), Facility Representative Program Performance Indicators  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2Q CY2003 (PDF), Facility Representative Program Performance 2Q CY2003 (PDF), Facility Representative Program Performance Indicators Quarterly Report 2Q CY2003 (PDF), Facility Representative Program Performance Indicators Quarterly Report Attached is the Facility Representative Program Performance Indicators (PIs) Quarterly Report Covering the Period from April to June 2003. Data for these indicators are gathered by Field elements Quarterly per DOE-STD-1063-2000, Facility Representatives, and reported to Headquarters program offices for evaluation and feedback in order to improve the facility Representative Program. A total of 13 Facility Representatives transferred to other positions during the quarter. Five of these accepted Facility Representative positions at other sites. Of the 8 that left the Program. 1 recieved a promotion and 7 accepted lateral positions. All of

496

2Q CY2002 (PDF), Facility Representative Program Performance Indicators  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2Q CY2002 (PDF), Facility Representative Program Performance 2Q CY2002 (PDF), Facility Representative Program Performance Indicators Quarterly Report 2Q CY2002 (PDF), Facility Representative Program Performance Indicators Quarterly Report The Facility Representive Program Performance Indicators (PIs) Quarterly Report is attached covering the period from April to June 2002. Data for these indicators are gathered by the Field elements quarterly per the Facility Representatives Standards , DOE-STD-1063-2000, and reported to Headquarters Program Offices for evaluation and feedback in order to improve the Facility Representative Program. The definition of the PIs from the Standard are also attached for your use in evaluating the data. Overall, the percentage of fully qualified Facility Representatives increased to 80% last quarter, from 78% the previous quarter , and

497

1Q CY2000, Facility Representative Program Performance Indicators  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

May May 9,2000 MEMORANDUM FOR DISTRIBUTION FROM: .yc,..,%$'! L.W.T oseph Arango, Facl ity Representative Program Manager (S-3.1) SUBJECT: Facility Representative Program Performance Indicators Quarterly Report The Facility Representative Program Performance Indicators (PIs) Quarterly Report is attached, covering the period from January 2000 to March 2000. Data for these indicators are gathered by the Field elements quarterly per the Facility Representatives Standard, DOE-STD-1 063, and reported to Headquarters Program Offices for evaluation and feedback in order to improve the Facility Representative Program. The definitions of the PIs from the Standard are also attached for your use in evaluating the data. You will note that the indicators show the attrition of five Facility Representatives from the program during this reporting period. Of those five, two were promoted

498

Bioenergy and Food Security Criteria and Indicators (BEFSCI) Website | Open  

Open Energy Info (EERE)

Bioenergy and Food Security Criteria and Indicators (BEFSCI) Website Bioenergy and Food Security Criteria and Indicators (BEFSCI) Website Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Bioenergy and Food Security Criteria and Indicators (BEFSCI) Website Focus Area: Other Biofuels Topics: Training Material Website: www.fao.org/bioenergy/foodsecurity/befsci/en/ Equivalent URI: cleanenergysolutions.org/content/bioenergy-and-food-security-criteria- Language: English Policies: Deployment Programs DeploymentPrograms: Technical Assistance This website-created by the Bioenergy and food Security project of the Food and Agriculture Organization of the United Nations (FAO)-provides policymakers and practitioners a set of criteria, indicators, good practices, and policy options for sustainable bioenergy production to

499

1Q CY2006 (PDF), Facility Representative Program Performance Indicators  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

6 (PDF), Facility Representative Program Performance 6 (PDF), Facility Representative Program Performance Indicators Quarterly Report 1Q CY2006 (PDF), Facility Representative Program Performance Indicators Quarterly Report Attached is the Facility Representative (FR) Program Performance Indicators Quarterly Report covering the period from January to March 2006. Data for these indicators are gathered by Field elements quarterly per DOE-STD-1063-2000, Facility Representatives and reported to Headquarters program offices for evaluation and feedback to improve the FR program. As of March 31,2006 81% of all FRs were fully qualified,up from 78% the previous quarter, and just above the DOE goal of 80%. To assist site offices in continuing to meet the qualification goal, there will be two focused training sessions for FR candidates in the coming months. These

500

4Q CY2002 (PDF), Facility Representative Program Performance Indicators  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2 (PDF), Facility Representative Program Performance 2 (PDF), Facility Representative Program Performance Indicators Quarterly Report 4Q CY2002 (PDF), Facility Representative Program Performance Indicators Quarterly Report Attached is the Facility Representative Program Performance Indicators (Pis) Quarterly Report Covering the Period from October to December 2002. Data for these indicators are gathered by Field elements Quarterly per DOE-STD-1063-2000, Facility Representatives, and reported to Headquarters program offices for evaluation and feedback in order to improve the facility Representative Program. The format of the report is changed from past reports. Information will now be provided according to the major offices having field or site office Facility Representative programs: National Nuclear Security Administration (NNSSA), the Office of