National Library of Energy BETA

Sample records for including marginal wells

  1. MARGINAL EXPENSE OIL WELL WIRELESS SURVEILLANCE MEOWS

    SciTech Connect (OSTI)

    Mason M. Medizade; John R. Ridgely; Donald G. Nelson

    2004-11-01

    A marginal expense oil well wireless surveillance system to monitor system performance and production from rod-pumped wells in real time from wells operated by Vaquero Energy in the Edison Field, Main Area of Kern County in California has been successfully designed and field tested. The surveillance system includes a proprietary flow sensor, a programmable transmitting unit, a base receiver and receiving antenna, and a base station computer equipped with software to interpret the data. First, the system design is presented. Second, field data obtained from three wells is shown. Results of the study show that an effective, cost competitive, real-time wireless surveillance system can be introduced to oil fields across the United States and the world.

  2. Marginal Expense Oil Well Wireless Surveillance (MEOWWS)

    SciTech Connect (OSTI)

    Nelson, Donald G.

    2002-03-11

    The objective of this study was to identify and field test a new, low cost, wireless oil well surveillance system. A variety of suppliers and technologies were considered. One supplier and system was chosen that was low cost, new to the oil field, and successfully field tested.

  3. Produce through coiled tubing to keep marginal wells unloaded

    SciTech Connect (OSTI)

    Not Available

    1986-12-01

    The use of coiled tubing as an alternate production tubing string has been attempted or considered by numerous operators in the past. However, its use has been tempered due to several problems known to be inherent with coiled tubing recompletions. Some of the problems encountered are: Killing the well to allow for tubing installation always carries the risk of formation damage; Candidate wells normally are marginal producers and may not produce sufficient revenue to justify the cost of a major workover; Procedures followed to install surface equipment may be hazardous; Previous installation designs required running the coiled tubing to the top of the tree, affecting the functional loss of all existing wellhead equipment; Often substandard modifications were required to reconnect into existing production facilities. However, a prototype spool and tubing hanger that incorporated modifications designed to solve these problems has been developed jointly by Reeled Tubing, Inc., and Well-head Control Systems. The solution is a new concept in the coiled tubing hanger. The design incorporates a floating element, which is a combination slip bowl, seal element and retaining sub. The entire assembly is installed and activated in the bore of a specially designed spool installed between the primary and secondary master valves of the existing wellhead.

  4. Economic Recovery of Oil Trapped at Fan Margins Using Hig Angle Wells Multiple Hydraulic Fractures

    SciTech Connect (OSTI)

    Laue, M.L.

    1997-11-21

    The Yowlumne field is a giant field in the southern San Joaquin basin, Kern County, California. It is a deep (13,000 ft) waterflood operation that produces from the Miocene- aged Stevens Sand. The reservoir is interpreted as a layered, fan-shaped, prograding turbidite complex containing several lobe-shaped sand bodies that represent distinct flow units. A high ultimate recovery factor is expected, yet significant quantities of undrained oil remain at the fan margins. The fan margins are not economic to develop using vertical wells because of thinning pay, deteriorating rock quality, and depth. This project attempts to demonstrate the effectiveness of exploiting the northeast distal fan margin through the use of a high- angle well completed with multiple hydraulic- fracture treatments. A high-angle well offers greater pay exposure than can be achieved with a vertical well. Hydraulic-fracture treatments will establish vertical communication between thin interbedded layers and the wellbore. The equivalent production rate and reserves of three vertical wells are anticipated at a cost of approximately two vertical wells. The near-horizontal well penetrated the Yowlumne sand; a Stevens sand equivalent, in the distal fan margin in the northeast area of the field. The well was drilled in a predominately westerly direction towards the interior of the field, in the direction of improving rock quality. Drilling and completion operations proved to be very challenging, leading to a number of adjustments to original plans. Hole conditions resulted in obtaining less core material than desired and setting intermediate casing 1200 ft too high. The 7 in. production liner stuck 1000 ft off bottom, requiring a 5 in. liner to be run the rest of the way. The cement job on the 5 in. liner resulted in a very poor bond, which precluded one of three hydraulic fracture treatments originally planned for the well. Openhole logs confirmed most expectations going into the project about basic rock properties: the formation was shaly with low porosities, and water saturations were in line with expectations, including the presence of some intervals swept out by the waterflood. High water saturations at the bottom of the well eliminated one of the originally planned hydraulic fracture treatments. Although porosities proved to be low, they were more uniform across the formation than expected. Permeabilities of the various intervals continue to be evaluated, but appear to be better than expected from the porosity log model derived in Budget Period One. The well was perforated in all pay sections behind the 5 in. liner. Production rates and phases agree nicely with log calculations, fractional flow calculations, and an analytical technique used to predict the rate performance of the well.

  5. Economic Recovery of Oil Trapped at Fan Margins Using High Angle Wells and Multiple Hydraulic Fractures

    SciTech Connect (OSTI)

    Mike L. Laue

    1997-05-30

    The distal fan margin in the northeast portion of the Yowlumne field contains significant reserves but is not economical to develop using vertical wells. Numerous interbedded shales and deteriorating rock properties limit producibility. In addition, extreme depths (13,000 ft) present a challenging environment for hydraulic fracturing and artificial lift. Lastly, a mature waterflood increases risk because of the uncertainty with size and location of flood fronts. This project attempts to demonstrate the effectiveness of exploiting the distal fan margin of this slope-basin clastic reservoir through the use of a high-angle well completed with multiple hydraulic-fracture treatments. The combination of a high-angle (or horizontal) well and hydraulic fracturing will allow greater pay exposure than can be achieved with conventional vertical wells while maintaining vertical communication between thin interbedded layers and the wellbore. The equivalent production rate and reserves of three vertical wells are anticipated at one-half to two-thirds the cost.

  6. Economic Recovery of Oil Trapped at Fan Margins Using High Angle Wells and Multiple Hydraulic fractures.

    SciTech Connect (OSTI)

    Laue, M.L.

    1997-08-31

    The long radius, near-horizontal well has been drilled and completion operations are in progress. Upon initial review of log data, two hydraulic fracture treatments were planned. However, the probability of the lower frac growing into thick sands previously swept by waterflood has called for additional information to be obtained prior to proceeding with hydraulic fracture treatments. Should permeabilities prove to be as favorable as some data indicate, produced water volumes could be excessively high. Prior to pumping the first frac, the well will be perforated and produced from lower pay intervals. These perfs will not impact future frac work. Rate data and pressure transient analysis will dictate the need for the lower frac.

  7. Economic recovery of oil trapped at fan margins using high angle wells and multiple hydraulic fractures. Annual report, September 28, 1995--September 27, 1996

    SciTech Connect (OSTI)

    Niemeyer, B.L.

    1997-09-01

    The digital fan margin in the northeast portion of the Yowlumne field contains significant reserves but is not economic to develop using verticle wells. Numerous interbedded shales and deteriorating rock properties limit producibility. In addition, extreme depths (13,000 ft) present a challenging environment for hydraulic fracturing and artificial lift. Lastly, a mature waterflood increases risk because of the uncertainty with size and location of flood fronts. This project attempts to demonstrate the effectiveness of exploiting the distal fan margin of this slope-basin clastic reservoir through the use of a high-angle well completed with multiple hydraulic-fracture treatments. The combination of a high-angle (or horizontal) well and hydraulic fracturing will allow greater pay exposure than can be achieved with conventional verticle wells while maintaining verticle communication between thin interbedded layers and the wellbore. The equivalent production rate and reserves of three verticle wells are anticipated at one-half to two-thirds the cost.

  8. Economic recovery of oil trapped at fan margins using high angle wells and multiple hydraulic fractures. Quarterly report, October 1--December 31, 1996

    SciTech Connect (OSTI)

    Laue, M.L.

    1997-02-13

    This project attempts to demonstrate the effectiveness of exploiting thin-layered, low-energy deposits at the distal margin of a prograding turbidite complex through the use of hydraulically- fractured horizontal or high-angle wells. The combination of a horizontal or high-angle well and hydraulic fracturing will allow greater pay exposure than can be achieved with conventional vertical wells while maintaining vertical communication between thin interbedded layers and the wellbore. A high-angle well will be drilled in the fan-margin portion of a slope-basin clastic reservoir and will be completed with multiple hydraulic-fracture treatments. Geologic modeling, reservoir characterization, and fine-grid reservoir simulation will be used to select the well location and orientation. Design parameters for the hydraulic-fracture treatments will be determined, in part, by fracturing an existing test well. Fracture azimuth will be predicted by passive seismic monitoring of a fracture-stimulation treatment in the test well using logging tools in an offset well. The Unites States Department of Energy granted approval of the continuation application to implement Budget Period Two effective November 21, 1996. The only Budget Period One activities for the quarter involved project administration. Budget Period Two activities were initiated with the development of a drilling program for the high-angle slant well. The well was spud on December 4, 1996 and was drilling at 10,830 ft in the vertical section of the hole as of the end of the month.

  9. Economic recovery of oil trapped at fan margins using high angle wells and multiple hydraulic fractures. Quarterly report, Apr 1--June 30, 1997

    SciTech Connect (OSTI)

    Laue, M.L.

    1997-08-31

    This project attempts to demonstrate the effectiveness of exploiting thin-layered, low-energy deposits at the distal margin of a prograding turbidite complex through the use of hydraulically-fractured horizontal or high-angle wells. The combination of a horizontal or high-angle well and hydraulic fracturing will allow greater pay exposure than can be achieved with conventional vertical wells while maintaining vertical communication between thin interbedded layers and the wellbore. A high-angle well will be drilled in the fan-margin portion of a slope-basin clastic reservoir and will be completed with multiple hydraulic-fracture treatments. Geologic modeling, reservoir characterization, and fine-grid reservoir simulation will be used to select the well location and orientation. Design parameters for the hydraulic-fracture treatments will be determined, in part, by fracturing an existing test well. Fracture azimuth will be predicted by passive seismic monitoring of a fracture-stimulation treatment in the test well using logging tools in an offset well. The long radius, near-horizontal well has been drilled and completion operations are in progress. Upon initial review of log data, two hydraulic fracture treatments were planned. However, the probability of the lower frac growing into thick sands previously swept by waterflood has called for additional information to be obtained prior to proceeding with hydraulic fracture treatments. Should permeabilities prove to be as favorable as some data indicate, produced water volumes could be excessively high. Prior to pumping the first frac, the well will be perforated and produced from lower pay intervals. These perfs will not impact future frac work. Rate data and pressure transient analysis will dictate the need for the lower frac.

  10. USING 3D COMPUTER MODELING, BOREHOLE GEOPHYSICS, AND HIGH CAPACITY PUMPS TO RESTORE PRODUCTION TO MARGINAL WELLS IN THE EAST TEXAS FIELD

    SciTech Connect (OSTI)

    R.L. Bassett

    2003-06-09

    Methods for extending the productive life of marginal wells in the East Texas Field were investigated using advanced computer imaging technology, geophysical tools, and selective perforation of existing wells. Funding was provided by the Department of Energy, TENECO Energy and Schlumberger Wireline and Testing. Drillers' logs for more than 100 wells in proximity to the project lease were acquired, converted to digital format using a numerical scheme, and the data were used to create a 3 Dimensional geological image of the project site. Using the descriptive drillers' logs in numerical format yielded useful cross sections identifying the Woodbine Austin Chalk contact and continuity of sand zones between wells. The geological data provided information about reservoir continuity, but not the amount of remaining oil, this was obtained using selective modern logs. Schlumberger logged the wells through 2 3/8 inch tubing with a new slimhole Reservoir Saturation Tool (RST) which can measure the oil and water content of the existing porosity, using neutron scattering and a gamma ray spectrometer (GST). The tool provided direct measurements of elemental content yielding interpretations of porosity, lithology, and oil and water content, confirming that significant oil saturation still exists, up to 50% in the upper Woodbine sand. Well testing was then begun and at the end of the project new oil was being produced from zones abandoned or bypassed more than 25 years ago.

  11. Completion Report for Well ER-12-4, Corrective Action Unit 99: Rainier Mesa - Shoshone Mountain (includes Errata Sheet)

    SciTech Connect (OSTI)

    U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office; Bechtel Nevada

    2006-05-01

    Well ER-12-4 was drilled for the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office, in support of the Nevada Environmental Restoration Project at the Nevada Test Site, Nye County, Nevada. This well was drilled in May 2005, as part of a hydrogeologic investigation program for the Rainier Mesa-Shoshone Mountain Corrective Action Unit in the north-central portion of the Nevada Test Site. The well is located on Rainier/Aqueduct Mesa, northwest of Yucca Flat, within Area 12 of the Nevada Test Site. The well provided information regarding the radiological and physical environment near underground nuclear tests conducted in U12t Tunnel, information on the pre-Tertiary rocks in the area, and depth to the regional water table.

  12. 2.2 Existing Facilities The HPL contains 51 structures, including the UMCES Administration Building and Well

    E-Print Network [OSTI]

    Boynton, Walter R.

    2.2 Existing Facilities The HPL contains 51 structures, including the UMCES Administration serving as the UMCES Administration Building. Below is a summary of the current condition of all information.) 370 UMCES Administration Building This two story (basement and first floor) former residence

  13. Coastal ocean margins program

    SciTech Connect (OSTI)

    Not Available

    1988-12-01

    The marine research program supported by the Office of Energy Research, Ecological Research Division, is focused to provide scientific information on major environmental issues facing development and expansion of most energy technologies and energy policy. These issues include waste disposal, siting/operations, and possible long term effects on global systems. The research is concentrated along the United States coastal margins where marine waters provide abundant food and resources while assimilating discharges from atmospheric, terrestrial, and aquatic sources. The program focuses on the formation and transport of particles within the waters of the continental shelf and the fate of these particles, whether on the shelf, on the slope, or in the open ocean. The program is conducted with multidisciplinary teams of researchers who investigate water mass movements, biological productivity, and naturally forming particles, as well as contaminant transport, to develop a clear understanding of the exchanges of contaminants and other materials that take place between continental shelf and open ocean waters. Seventy-five percent of the projects are funded to university grantees and twenty-five percent to National Laboratories.

  14. Hanford wells

    SciTech Connect (OSTI)

    Chamness, M.A.; Merz, J.K.

    1993-08-01

    Records describing wells located on or near the Hanford Site have been maintained by Pacific Northwest Laboratory and the operating contractor, Westinghouse Hanford Company. In support of the Ground-Water Surveillance Project, portions of the data contained in these records have been compiled into the following report, which is intended to be used by those needing a condensed, tabular summary of well location and basic construction information. The wells listed in this report were constructed over a period of time spanning almost 70 years. Data included in this report were retrieved from the Hanford Envirorunental Information System (HEIS) database and supplemented with information not yet entered into HEIS. While considerable effort has been made to obtain the most accurate and complete tabulations possible of the Hanford Site wells, omissions and errors may exist. This document does not include data on lithologic logs, ground-water analyses, or specific well completion details.

  15. INTRODUCTION Margin evolution and plate-reconstruction models require a

    E-Print Network [OSTI]

    Müller, Dietmar

    ­243 Formation and evolution of Australian passive margins: implications for locating the boundary between. STAGG2 AND P. A. SYMONDS2 1 Division of Geology and Geophysics, Building F05, School of Geosciences. Australian passive margins display a large variety of styles, including narrow, wide, volcanic and non

  16. Monitoring well

    DOE Patents [OSTI]

    Hubbell, Joel M. (Idaho Falls, ID); Sisson, James B. (Idaho Falls, ID)

    1999-01-01

    A monitoring well including a conduit defining a passageway, the conduit having a proximal and opposite, distal end; a coupler connected in fluid flowing relationship with the passageway; and a porous housing borne by the coupler and connected in fluid flowing relation thereto.

  17. Monitoring well

    DOE Patents [OSTI]

    Hubbell, J.M.; Sisson, J.B.

    1999-06-29

    A monitoring well is described which includes: a conduit defining a passageway, the conduit having a proximal and opposite, distal end; a coupler connected in fluid flowing relationship with the passageway; and a porous housing borne by the coupler and connected in fluid flowing relation thereto. 8 figs.

  18. Well pump

    DOE Patents [OSTI]

    Ames, Kenneth R. (Pasco, WA); Doesburg, James M. (Chicago, IL)

    1987-01-01

    A well pump includes a piston and an inlet and/or outlet valve assembly of special structure. Each is formed of a body of organic polymer, preferably PTFE. Each includes a cavity in its upper portion and at least one passage leading from the cavity to the bottom of the block. A screen covers each cavity and a valve disk covers each screen. Flexible sealing flanges extend upwardly and downwardly from the periphery of the piston block. The outlet valve block has a sliding block and sealing fit with the piston rod.

  19. Monitoring well

    DOE Patents [OSTI]

    Hubbell, Joel M. (Idaho Falls, ID); Sisson, James B. (Idaho Falls, ID)

    2002-01-01

    The present invention relates to a monitoring well which includes an enclosure defining a cavity and a water reservoir enclosed within the cavity and wherein the reservoir has an inlet and an outlet. The monitoring well further includes a porous housing borne by the enclosure and which defines a fluid chamber which is oriented in fluid communication with the outlet of the reservoir, and wherein the porous housing is positioned in an earthen soil location below-grade. A geophysical monitoring device is provided and mounted in sensing relation relative to the fluid chamber of the porous housing; and a coupler is selectively moveable relative to the outlet of reservoir to couple the porous housing and water reservoir in fluid communication. An actuator is coupled in force transmitting relation relative to the coupler to selectively position the coupler in a location to allow fluid communication between the reservoir and the fluid chamber defined by the porous housing.

  20. Corrective Action Investigation Plan for Corrective Action Unit 165: Areas 25 and 26 Dry Well and Washdown Areas, Nevada Test Site, Nevada (including Record of Technical Change Nos. 1, 2, and 3) (January 2002, Rev. 0)

    SciTech Connect (OSTI)

    U.S. Department of Energy, National Nuclear Security Administration Nevada Operations Office (NNSA/NV)

    2002-01-09

    This Corrective Action Investigation Plan contains the U.S. Department of Energy, National Nuclear Security Administration Nevada Operations Office's approach to collect the data necessary to evaluate corrective action alternatives appropriate for the closure of Corrective Action Unit (CAU) 165 under the Federal Facility Agreement and Consent Order. Corrective Action Unit 165 consists of eight Corrective Action Sites (CASs): CAS 25-20-01, Lab Drain Dry Well; CAS 25-51-02, Dry Well; CAS 25-59-01, Septic System; CAS 26-59-01, Septic System; CAS 25-07-06, Train Decontamination Area; CAS 25-07-07, Vehicle Washdown; CAS 26-07-01, Vehicle Washdown Station; and CAS 25-47-01, Reservoir and French Drain. All eight CASs are located in the Nevada Test Site, Nevada. Six of these CASs are located in Area 25 facilities and two CASs are located in Area 26 facilities. The eight CASs at CAU 165 consist of dry wells, septic systems, decontamination pads, and a reservoir. The six CASs in Area 25 are associated with the Nuclear Rocket Development Station that operated from 1958 to 1973. The two CASs in Area 26 are associated with facilities constructed for Project Pluto, a series of nuclear reactor tests conducted between 1961 to 1964 to develop a nuclear-powered ramjet engine. Based on site history, the scope of this plan will be a two-phased approach to investigate the possible presence of hazardous and/or radioactive constituents at concentrations that could potentially pose a threat to human health and the environment. The Phase I analytical program for most CASs will include volatile organic compounds, semivolatile organic compounds, Resource Conservation and Recovery Act metals, total petroleum hydrocarbons, polychlorinated biphenyls, and radionuclides. If laboratory data obtained from the Phase I investigation indicates the presence of contaminants of concern, the process will continue with a Phase II investigation to define the extent of contamination. Based on the results of Phase I sampling, the analytical program for Phase II investigation may be reduced. The results of this field investigation will support a defensible evaluation of corrective action alternatives in the corrective action decision document.

  1. Radiotherapy margin design with particular consideration of high curvature CTVs

    SciTech Connect (OSTI)

    Herschtal, Alan; Kron, Tomas; Fox, Chris [Peter MacCallum Cancer Centre, St. Andrews Place, E. Melbourne, Victoria 3002 (Australia)

    2009-03-15

    In applying 3D conformal radiation therapy to a tumor clinical target volume (CTV), a margin is added around the CTV to account for any sources of error in the application of treatment which may result in misalignment between the CTV and the dose distribution actually delivered. The volume enclosed within the CTV plus the margin is known as the PTV, or planning target volume. The larger the errors are anticipated to be, the wider the margin will need to be to accommodate those errors. Based on the approach of van Herk et al. [''The probability of correct target dosage: Dose-population histograms for deriving treatment margins in radiotherapy,'' Int. J. Radiat. Oncol. Biol., Phys. 47(4), 1121-1135 (2000)] this paper develops the mathematical theory behind the calculation of the margin width required to ensure that the entire CTV receives sufficiently high dose with sufficiently high probability. The margin recipe developed not only considers the magnitude of the errors but also includes a term to adjust for curved CTV surfaces. In doing so, the accuracy of the margin recipe is enhanced yet remains mathematically concise enough to be readily implemented in the clinical setting. The results are particularly relevant for clinical situations in which the uncertainties in treatment are large relative to the size of the CTV.

  2. Well Placement

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Well Placement Well Placement LANL maintains an extensive groundwater monitoring and surveillance program through sampling. August 1, 2013 Finished groundwater well head with solar...

  3. IMPROVING EFFICIENT MARGINAL ESTIMATORS IN BIVARIATE MODELS WITH PARAMETRIC MARGINALS

    E-Print Network [OSTI]

    Schick, Anton

    AND ANTON SCHICK Abstract. Suppose we have data from a bivariate model with parametric marginals. Efficient nonparametric estimators in the presence of a constraint, see e.g. Schick and Wefelmeyer (2008) for a recent = The research of Hanxiang Peng was supported in parts by NSF Grant DMS 0940365. The research of Anton Schick

  4. Recursive Pathways to Marginal Likelihood Estimation with Prior-Sensitivity Analysis

    E-Print Network [OSTI]

    Cameron, Ewan

    2013-01-01

    We investigate the utility to contemporary Bayesian studies of recursive, Gauss-Seidel-type pathways to marginal likelihood estimation characterized by reverse logistic regression and the density of states. Through a pair of illustrative, numerical examples (including mixture modeling of the well-known 'galaxy dataset') we highlight both the remarkable diversity of bridging schemes amenable to recursive normalization and the notable efficiency of the resulting pseudo-mixture densities for gauging prior-sensitivity in the model selection context. Our key theoretical contributions show the connection between the nested sampling identity and the density of states. Further, we introduce a novel heuristic ('thermodynamic integration via importance sampling') for qualifying the role of the bridging sequence in marginal likelihood estimation. An efficient pseudo-mixture density scheme for harnessing the information content of otherwise discarded draws in ellipse-based nested sampling is also introduced.

  5. Horizontal well replaces hydraulic fracturing in North Sea gas well

    SciTech Connect (OSTI)

    Reynolds, D.A.; Seymour, K.P. )

    1991-11-25

    This paper reports on excessive water production from hydraulically fractured wells in a poor quality reservoir in the North SEa which prompted the drilling of a horizontal well. Gas production from the horizontal well reached six times that of the offset vertical wells, and no water production occurred. This horizontal well proved commercial the western section of the Anglia field. Horizontal drilling in the North SEa is as an effective technology to enhance hydrocarbon recovery from reservoirs that previously had proven uncommercial with other standard techniques. It is viable for the development of marginal reservoirs, particularly where conditions preclude stimulation from hydraulic fracturing.

  6. Pattern of Failure After Limited Margin Radiotherapy and Temozolomide for Glioblastoma

    SciTech Connect (OSTI)

    McDonald, Mark W.; Shu, Hui-Kuo G.; Curran, Walter J.; Crocker, Ian R.

    2011-01-01

    Purpose: To evaluate the pattern of failure after limited margin radiotherapy for glioblastoma. Methods and Materials: We analyzed 62 consecutive patients with newly diagnosed glioblastoma treated between 2006 and 2008 with standard fractionation to a total dose of 60Gy with concurrent temozolomide (97%) or arsenic trioxide (3%). The initial clinical target volume included postoperative T2 abnormality with a median margin of 0.7cm. The boost clinical target volume included residual T1-enhancing tumor and resection cavity with a median margin of 0.5cm. Planning target volumes added a 0.3- or 0.5-cm margin to clinical target volumes. The total boost planning target volume (PTV{sub boost}) margin was 1cm or less in 92% of patients. The volume of recurrent tumor (new T1 enhancement) was categorized by the percent within the 60-Gy isodose line as central (>95%), infield (81-95%), marginal (20-80%), or distant (<20%). For comparison, an initial planning target volume with a 2-cm margin and PTV{sub boost} with a 2.5-cm margin were created for each patient. Results: With a median follow-up of 12 months, radiographic tumor progression developed in 43 of 62 patients. Imaging was available for analysis in 41: 38 (93%) had central or infield failure, 2 (5%) had marginal failure, and 1 (2%) had distant failure relative to the 60-Gy isodose line. The treated PTV{sub boost} (median, 140cm{sup 3}) was, on average, 70% less than the PTV{sub boost} with a 2.5-cm margin (median, 477cm{sup 3}) (p < 0.001). Conclusions: A PTV{sub boost} margin of 1cm or less did not appear to increase the risk of marginal and/or distant tumor failures compared with other published series. With careful radiation planning and delivery, it appears that treatment margins for glioblastoma can be reduced.

  7. Regnar -- Development of a marginal field

    SciTech Connect (OSTI)

    Thalund, K.M.; Brodersen, F.P.; Roigaard-Petersen, B.

    1994-12-31

    Regnar is a small marginal field located some 13 km from the main Dan F complex and is the first subsea completion in Danish waters, operated by Maersk Olie og Gas AS. A short lifetime has been predicted for the field which therefore has been developed as a low cost project, using a combination of subsea technology and minimum topside facilities. Regnar consists of a subsea x-mas tree producing through a 6 inch pipeline with a 2 1/2 inch chemical piggyback line to Dan F. The x-mas tree and the subsea choke valve are controlled from a buoy moored nearby the well. The buoy is radio linked to Dan F. The Regnar field was brought on stream on September 26, 1993.

  8. Dynamics of the continental margins

    SciTech Connect (OSTI)

    Not Available

    1990-11-01

    On 18--20 June 1990, over 70 oceanographers conducting research in the ocean margins of North America attended a workshop in Virginia Beach, Virginia. The purpose of the workshop was to provide the Department of Energy with recommendations for future research on the exchange of energy-related materials between the coastal and interior ocean and the relationship between the ocean margins and global change. The workshop was designed to optimize the interaction of scientists from specific research disciplines (biology, chemistry, physics and geology) as they developed hypotheses, research questions and topics and implementation plans. The participants were given few restraints on the research they proposed other than realistic time and monetary limits. The interdisciplinary structure of the meeting promoted lively discussion and creative research plans. The meeting was divided into four working groups based on lateral, vertical, air/sea and sediment/water processes. Working papers were prepared and distributed before the meeting. During the meeting the groups revised the papers and added recommendations that appear in this report, which was reviewed by an Executive Committee.

  9. Assessment of seismic margin calculation methods

    SciTech Connect (OSTI)

    Kennedy, R.P.; Murray, R.C.; Ravindra, M.K.; Reed, J.W.; Stevenson, J.D.

    1989-03-01

    Seismic margin review of nuclear power plants requires that the High Confidence of Low Probability of Failure (HCLPF) capacity be calculated for certain components. The candidate methods for calculating the HCLPF capacity as recommended by the Expert Panel on Quantification of Seismic Margins are the Conservative Deterministic Failure Margin (CDFM) method and the Fragility Analysis (FA) method. The present study evaluated these two methods using some representative components in order to provide further guidance in conducting seismic margin reviews. It is concluded that either of the two methods could be used for calculating HCLPF capacities. 21 refs., 9 figs., 6 tabs.

  10. Well Placement

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power AdministrationRobust,Field-effectWorking WithTelecentricN AProjectAdministration NNSAWell Placement Well

  11. Subsidence history, crustal structure, and evolution of the Somaliland-Yemen conjugate margin

    E-Print Network [OSTI]

    Ali, Mohammed

    seismic refraction data and process-oriented gravity and flexure modeling. The margin is asymmetric et al., 2001; Dauteuil et al., 2001; Hebert et al., 2001; Manighetti et al., 1997]. Seismic and well

  12. Multivariate Distributions with Proportional Reversed Hazard Marginals

    E-Print Network [OSTI]

    Kundu, Debasis

    Multivariate Distributions with Proportional Reversed Hazard Marginals Debasis Kundu1 & Manuel Franco2 & Juana-Maria Vivo3 Abstract Several univariate proportional reversed hazard models have been a class of bivariate models with proportional reversed hazard marginals. It is observed that the proposed

  13. How ARCO drills high-angle wells offshore Indonesia

    SciTech Connect (OSTI)

    Tjondrodiputro, B.; Eddyarso, H.; Jones, K. (Atlantic Richfield Indonesia, Inc., Jakarta (Indonesia))

    1993-03-01

    Atlantic Richfield Indonesia, Inc. (ARII) drilled and completed 28 high-angle wells since early 1986 in Bima, Papa and FF fields in the Offshore North West Java Sea (ONWJ) contract area. Early wells were drilled with conventional rotary bottomhole assemblies (BHAs); introduction of a steerable tool and MWD subsequently increased efficiency and reduced drilling costs. Both lignosulfonate and dispersed pac polymer muds have been used with good success. Cost to drill a high-angle well has been only marginally more than that of a 45[degree] directional well. Elimination of open hole logging and use of preperforated liners have reduced drilling costs by 10%. Production performance for wells has been higher than for vertical or low-angle wells. High-angle wells in Bima have outperformed offset vertical wells and are classified as a success. However, horizontal wells in Papa, which has a strong bottom-water drive, have not shown any improved recovery over conventional wells. The new well in FF field is still being evaluated. In this first of a two-part report, high-angle drilling operations including well planning, BHA selection, casing and mud programs, hole cleaning and logging are described. Specific wells in the Bima area are discussed as examples.

  14. Petroleum geology of Pacific margin of Central America and northern South America, from Guatemala to Ecuador

    SciTech Connect (OSTI)

    Scrutton, M.E.; Escalante, G.F.

    1986-07-01

    Exploration for hydrocarbons along the Pacific margin of Central America and northern South America has been limited and spasmodic. Less than 100 exploration wells have been drilled, with nearly 50 of these being in the Santa Elena, Progreso, and Guayas basins in Ecuador. Shows have been reported in some wells, and a few oil seeps are known. The only commercial production established to date has been from the Santa Elena Peninsula in Ecuador in the extreme south of the study area. Understanding of the geology in this part of the continental margin is incomplete at best. This paper reviews present-day knowledge in an attempt to define the sedimentary basins better, to characterize their structure and stratigraphy, and to assess their petroleum prospects. The area of continental margin reviewed is to the north, located northwest of the trench system where oceanic crust of the Cocos plate subducts under the Caribbean plate, and to the south, where the northern part of the Nazca plate collides with the South American plate. This plate tectonic setting forms the framework on which local structural and sedimentary events have created a series of relatively small trench-slope and forearc basins in what is now the coastal plain and adjacent offshore area of Central and South America, south or west of a line of mountain ranges with active volcanism. Sedimentary fill is generally of Tertiary age. The basins and subbasins recognized and described include: in Ecuador - Guayas, Santa Elena, Progreso, Valdivia, Bajo Grande, Manta, Muisne-Esmeraldas, and Borbon; in Colombia - Choco-Pacific; in Panama - Gulf of Panama basin complex (Santiago, Tonosi, Sambu), and Burica-Chiriqui; in Costa Rica - Terraba and Coronado/Tempisque; in Nicaragua - San Juan del Sur; and in the Honduras, El Salvador, and Guatemala - the Pacific coastal basin.

  15. Electromagnetic exploration of the Exmouth and Vøring rifted margins

    E-Print Network [OSTI]

    Myer, David Gerard

    2012-01-01

    Haq, B.U. , 1992. Seismic stratigraphy and passive marginHaq, B.U. , 1992. Seismic stratigraphy and passive marginHaq, B.U. , 1992. Seismic stratigraphy and passive margin

  16. Margins, Liquidity and the Cost of Hedging

    E-Print Network [OSTI]

    Mello, Antonio S.

    2012-05-21

    Recent financial reforms, such as the Dodd-Frank Act in the U.S. and the European Market Infrastructure Regulation, encourage greater use of clearing and therefore increased margining of derivative trades. They also impose ...

  17. On the quantification of safety margins

    E-Print Network [OSTI]

    Pagani, Lorenzo P

    2004-01-01

    The nuclear industry has relied on the concept of Defense in Depth (DID) and traditional safety margins to deal with the uncertainties associated with the design and operation of nuclear facilities. These concepts were ...

  18. The law of demand versus diminishing marginal utility

    E-Print Network [OSTI]

    Bettie, Bruce R.; Lafrance, Jeffrey T.

    2006-01-01

    Diminishing marginal utility will provide a negative sloperegularity for u. Thus, this utility function (or a simpleDiminishing Marginal Utility Endnotes References Burt,

  19. Marginal Energy Price Report - July 1999 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Report - July 1999 Marginal Energy Price Report - July 1999 Estimated Consumer Marginal Energy Prices for the Commercial and Residental Sectors for use in the Life-Cycle Cost...

  20. ORBITAL MIGRATION OF PROTOPLANETS IN A MARGINALLY GRAVITATIONALLY UNSTABLE DISK

    SciTech Connect (OSTI)

    Boss, Alan P.

    2013-02-20

    Core accretion and disk instability require giant protoplanets to form in the presence of disk gas. Protoplanet migration models generally assume disk masses low enough that the disk's self-gravity can be neglected. However, disk instability requires a disk massive enough to be marginally gravitationally unstable (MGU). Even for core accretion, an FU Orionis outburst may require a brief MGU disk phase. We present a new set of three-dimensional, gravitational radiation hydrodynamics models of MGU disks with multiple protoplanets, which interact gravitationally with the disk and with each other, including disk gas mass accretion. Initial protoplanet masses are 0.01 to 10 M {sub Circled-Plus} for core accretion models, and 0.1 to 3 M {sub Jup} for Nice scenario models, starting on circular orbits with radii of 6, 8, 10, or 12 AU, inside a 0.091 M {sub Sun} disk extending from 4 to 20 AU around a 1 M {sub Sun} protostar. Evolutions are followed for up to {approx}4000 yr and involve phases of relative stability (e {approx} 0.1) interspersed with chaotic phases (e {approx} 0.4) of orbital interchanges. The 0.01 to 10 M {sub Circled-Plus} cores can orbit stably for {approx}1000 yr: monotonic inward or outward orbital migration of the type seen in low mass disks does not occur. A system with giant planet masses similar to our solar system (1.0, 0.33, 0.1, 0.1 M {sub Jup}) was stable for over 1000 yr, and a Jupiter-Saturn-like system was stable for over 3800 yr, implying that our giant planets might well survive an MGU disk phase.

  1. Self-Tuning PI TCP Flow Controller for AQM Routers With Interval Gain and Phase Margin Assignment

    E-Print Network [OSTI]

    Huang, Changcheng

    -tuning proportional-integral (PI) controller for Active Queue Management (AQM) in the Internet. Classical control to achieve good AQM performance while adapting the AQM control system to great traffic load changes very well Queue Management, PI Control, Gain Margin, Phase Margin, Self-Tune 1. INTRODUCTION Congestion control

  2. Electromagnetic exploration of the Exmouth and Vøring rifted margins

    E-Print Network [OSTI]

    Myer, David Gerard

    2012-01-01

    continental margin; seismic interpretation, stratigraphy,CSEM, and seismic interpretation; (c) investigate the effect

  3. Risk Informed Margins Management as part of Risk Informed Safety Margin Characterization

    SciTech Connect (OSTI)

    Curtis Smith

    2014-06-01

    The ability to better characterize and quantify safety margin is important to improved decision making about Light Water Reactor (LWR) design, operation, and plant life extension. A systematic approach to characterization of safety margins and the subsequent margin management options represents a vital input to the licensee and regulatory analysis and decision making that will be involved. In addition, as research and development in the LWR Sustainability (LWRS) Program and other collaborative efforts yield new data, sensors, and improved scientific understanding of physical processes that govern the aging and degradation of plant SSCs needs and opportunities to better optimize plant safety and performance will become known. To support decision making related to economics, readability, and safety, the Risk Informed Safety Margin Characterization (RISMC) Pathway provides methods and tools that enable mitigation options known as risk informed margins management (RIMM) strategies.

  4. Anisotropic Margin Expansions in 6 Anatomic Directions for Oropharyngeal Image Guided Radiation Therapy

    SciTech Connect (OSTI)

    Yock, Adam D. [Department of Radiation Physics, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Graduate School of Biomedical Sciences, The University of Texas Health Science Center at Houston, Houston, Texas (United States); Garden, Adam S. [Department of Radiation Oncology, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Court, Laurence E. [Department of Radiation Physics, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Graduate School of Biomedical Sciences, The University of Texas Health Science Center at Houston, Houston, Texas (United States); Beadle, Beth M. [Department of Radiation Oncology, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Zhang, Lifei [Department of Radiation Physics, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Dong, Lei, E-mail: dong.lei@scrippshealth.org [Department of Radiation Physics, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Graduate School of Biomedical Sciences, The University of Texas Health Science Center at Houston, Houston, Texas (United States)

    2013-11-01

    Purpose: The purpose of this work was to determine the expansions in 6 anatomic directions that produced optimal margins considering nonrigid setup errors and tissue deformation for patients receiving image-guided radiation therapy (IGRT) of the oropharynx. Methods and Materials: For 20 patients who had received IGRT to the head and neck, we deformably registered each patient's daily images acquired with a computed tomography (CT)-on-rails system to his or her planning CT. By use of the resulting vector fields, the positions of volume elements within the clinical target volume (CTV) (target voxels) or within a 1-cm shell surrounding the CTV (normal tissue voxels) on the planning CT were identified on each daily CT. We generated a total of 15,625 margins by dilating the CTV by 1, 2, 3, 4, or 5 mm in the posterior, anterior, lateral, medial, inferior, and superior directions. The optimal margins were those that minimized the relative volume of normal tissue voxels positioned within the margin while satisfying 1 of 4 geometric target coverage criteria and 1 of 3 population criteria. Results: Each pair of geometric target coverage and population criteria resulted in a unique, anisotropic, optimal margin. The optimal margin expansions ranged in magnitude from 1 to 5 mm depending on the anatomic direction of the expansion and on the geometric target coverage and population criteria. Typically, the expansions were largest in the medial direction, were smallest in the lateral direction, and increased with the demand of the criteria. The anisotropic margin resulting from the optimal set of expansions always included less normal tissue than did any isotropic margin that satisfied the same pair of criteria. Conclusions: We demonstrated the potential of anisotropic margins to reduce normal tissue exposure without compromising target coverage in IGRT to the head and neck.

  5. SUESS ET AL.: SEA FLOOR METHANE HYDRATES AT HYDRATE RIDGE, CASCADIA MARGIN Sea Floor Methane Hydrates at Hydrate Ridge, Cascadia Margin

    E-Print Network [OSTI]

    Goldfinger, Chris

    SUESS ET AL.: SEA FLOOR METHANE HYDRATES AT HYDRATE RIDGE, CASCADIA MARGIN 1 Sea Floor Methane are exposed at the sea floor. A methane-oxidizing bacterial consortium populates the exposures of hydrate; colonies of vent macro-fauna are abundant as well. Discharge of methane from destabilized hydrate

  6. Experimental validation of the van Herk margin formula for lung radiation therapy

    SciTech Connect (OSTI)

    Ecclestone, Gillian; Heath, Emily; Bissonnette, Jean-Pierre

    2013-11-15

    Purpose: To validate the van Herk margin formula for lung radiation therapy using realistic dose calculation algorithms and respiratory motion modeling. The robustness of the margin formula against variations in lesion size, peak-to-peak motion amplitude, tissue density, treatment technique, and plan conformity was assessed, along with the margin formula assumption of a homogeneous dose distribution with perfect plan conformity.Methods: 3DCRT and IMRT lung treatment plans were generated within the ORBIT treatment planning platform (RaySearch Laboratories, Sweden) on 4DCT datasets of virtual phantoms. Random and systematic respiratory motion induced errors were simulated using deformable registration and dose accumulation tools available within ORBIT for simulated cases of varying lesion sizes, peak-to-peak motion amplitudes, tissue densities, and plan conformities. A detailed comparison between the margin formula dose profile model, the planned dose profiles, and penumbra widths was also conducted to test the assumptions of the margin formula. Finally, a correction to account for imperfect plan conformity was tested as well as a novel application of the margin formula that accounts for the patient-specific motion trajectory.Results: The van Herk margin formula ensured full clinical target volume coverage for all 3DCRT and IMRT plans of all conformities with the exception of small lesions in soft tissue. No dosimetric trends with respect to plan technique or lesion size were observed for the systematic and random error simulations. However, accumulated plans showed that plan conformity decreased with increasing tumor motion amplitude. When comparing dose profiles assumed in the margin formula model to the treatment plans, discrepancies in the low dose regions were observed for the random and systematic error simulations. However, the margin formula respected, in all experiments, the 95% dose coverage required for planning target volume (PTV) margin derivation, as defined by the ICRU; thus, suitable PTV margins were estimated. The penumbra widths calculated in lung tissue for each plan were found to be very similar to the 6.4 mm value assumed by the margin formula model. The plan conformity correction yielded inconsistent results which were largely affected by image and dose grid resolution while the trajectory modified PTV plans yielded a dosimetric benefit over the standard internal target volumes approach with up to a 5% decrease in the V20 value.Conclusions: The margin formula showed to be robust against variations in tumor size and motion, treatment technique, plan conformity, as well as low tissue density. This was validated by maintaining coverage of all of the derived PTVs by 95% dose level, as required by the formal definition of the PTV. However, the assumption of perfect plan conformity in the margin formula derivation yields conservative margin estimation. Future modifications to the margin formula will require a correction for plan conformity. Plan conformity can also be improved by using the proposed trajectory modified PTV planning approach. This proves especially beneficial for tumors with a large anterior–posterior component of respiratory motion.

  7. Thermal indicator for wells

    DOE Patents [OSTI]

    Gaven, Jr., Joseph V. (Oakton, VA); Bak, Chan S. (Newbury Park, CA)

    1983-01-01

    Minute durable plate-like thermal indicators are employed for precision measuring static and dynamic temperatures of well drilling fluids. The indicators are small enough and sufficiently durable to be circulated in the well with drilling fluids during the drilling operation. The indicators include a heat resistant indicating layer, a coacting meltable solid component and a retainer body which serves to unitize each indicator and which may carry permanent indicator identifying indicia. The indicators are recovered from the drilling fluid at ground level by known techniques.

  8. Pump apparatus including deconsolidator

    DOE Patents [OSTI]

    Sonwane, Chandrashekhar; Saunders, Timothy; Fitzsimmons, Mark Andrew

    2014-10-07

    A pump apparatus includes a particulate pump that defines a passage that extends from an inlet to an outlet. A duct is in flow communication with the outlet. The duct includes a deconsolidator configured to fragment particle agglomerates received from the passage.

  9. Isobaric groundwater well

    DOE Patents [OSTI]

    Hubbell, Joel M. (Idaho Falls, ID); Sisson, James B. (Idaho Falls, ID)

    1999-01-01

    A method of measuring a parameter in a well, under isobaric conditions, including such parameters as hydraulic gradient, pressure, water level, soil moisture content and/or aquifer properties the method as presented comprising providing a casing having first and second opposite ends, and a length between the ends, the casing supporting a transducer having a reference port; placing the casing lengthwise into the well, second end first, with the reference port vented above the water table in the well; and sealing the first end. A system is presented for measuring a parameter in a well, the system comprising a casing having first and second opposite ends, and a length between the ends and being configured to be placed lengthwise into a well second end first; a transducer, the transducer having a reference port, the reference port being vented in the well above the water table, the casing being screened across and above the water table; and a sealing member sealing the first end. In one embodiment, the transducer is a tensiometer transducer and in other described embodiments, another type transducer is used in addition to a tensiometer.

  10. Cenozoic stratigraphyand subsidence historyof the South China Sea margin in theTaiwan region

    E-Print Network [OSTI]

    Lin, Andrew Tien-Shun

    Cenozoic stratigraphyand subsidence historyof the South China Sea margin in theTaiwan region A. T, together with the subsidence analysis of deep wells, show that during rifting (B58^37Ma post-breakup subsidence (B30^18Ma) possibly as the inferred induced convection abated following initial

  11. Unitary-process discrimination with error margin

    E-Print Network [OSTI]

    T. Hashimoto; A. Hayashi; M. Hayashi; M. Horibe

    2010-06-10

    We investigate a discrimination scheme between unitary processes. By introducing a margin for the probability of erroneous guess, this scheme interpolates the two standard discrimination schemes: minimum-error and unambiguous discrimination. We present solutions for two cases. One is the case of two unitary processes with general prior probabilities. The other is the case with a group symmetry: the processes comprise a projective representation of a finite group. In the latter case, we found that unambiguous discrimination is a kind of "all or nothing": the maximum success probability is either 0 or 1. We also closely analyze how entanglement with an auxiliary system improves discrimination performance.

  12. Caldera Rim Margins | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmentalBowerbank, Maine:Kansas: Energy ResourcesParish,Caldera Rim Margins Jump to:

  13. Marginal Energy Prices - RECS97 Update

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustmentsShirleyEnergyTher i nAand DOE Safetyof Energy ThisSites |and theDepartment ofMarchMarginal

  14. Thermal well-test method

    DOE Patents [OSTI]

    Tsang, Chin-Fu (Albany, CA); Doughty, Christine A. (Berkeley, CA)

    1985-01-01

    A well-test method involving injection of hot (or cold) water into a groundwater aquifer, or injecting cold water into a geothermal reservoir. By making temperature measurements at various depths in one or more observation wells, certain properties of the aquifer are determined. These properties, not obtainable from conventional well test procedures, include the permeability anisotropy, and layering in the aquifer, and in-situ thermal properties. The temperature measurements at various depths are obtained from thermistors mounted in the observation wells.

  15. Wilson cycles, tectonic inheritance, and rifting of the North American Gulf of Mexico continental margin

    E-Print Network [OSTI]

    Huerta, Audrey D.

    Wilson cycles, tectonic inheritance, and rifting of the North American Gulf of Mexico continental, Fort Collins, Colorado 80523, USA ABSTRACT The tectonic evolution of the North Amer- ican Gulf of Mexico margin, including the Interior Salt Basin, outboard unextended Wiggins arch, and an unusually

  16. Continuous Contour Monte Carlo for Marginal Density Estimation With an Application to a

    E-Print Network [OSTI]

    Liang, Faming

    ; Gelman and Meng 1998), reverse logistic regression (Geyer 1994), marginal likelihood (Chib 1995; Chib; Reversible jump Markov chain Monte Carlo; Stochastic approximation; Wang-Landau algorithm. 1. INTRODUCTION;Continuous Contour Monte Carlo 609 variety of approaches including reversible jump MCMC (Green 1995; Green

  17. Well having inhibited microbial growth

    DOE Patents [OSTI]

    Lee, Brady D.; Dooley, Kirk J.

    2006-08-15

    The invention includes methods of inhibiting microbial growth in a well. A packing material containing a mixture of a first material and an antimicrobial agent is provided to at least partially fill a well bore. One or more access tubes are provided in an annular space around a casing within the well bore. The access tubes have a first terminal opening located at or above a ground surface and have a length that extends from the first terminal opening at least part of the depth of the well bore. The access tubes have a second terminal opening located within the well bore. An antimicrobial material is supplied into the well bore through the first terminal opening of the access tubes. The invention also includes well constructs.

  18. Decontaminating Flooded Wells 

    E-Print Network [OSTI]

    Boellstorff, Diana; Dozier, Monty; Provin, Tony; Dictson, Nikkoal; McFarland, Mark L.

    2005-09-30

    This publication explains how to decontaminate and disinfect a well, test the well water and check for well damage after a flood....

  19. Sandia Energy - NASA Award for Marginal Ice Zone Observations...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NASA Award for Marginal Ice Zone Observations and Process Experiment (MIZOPEX) Home Climate Office of Science News News & Events Research & Capabilities Monitoring Analysis...

  20. The Law of Demand versus Diminishing Marginal Utility

    E-Print Network [OSTI]

    Beattie, Bruce R.; LaFrance, Jeffrey T

    2006-01-01

    not guarantee DSD. This form of utility function generates aHausman). This type of utility model is commonplace amongversus Diminishing Marginal Utility References Burt, O.R.

  1. The Law of Demand Versus Diminishing Marginal Utility

    E-Print Network [OSTI]

    Beattie, Bruce R.; LaFrance, Jeffrey T.

    2006-01-01

    not guarantee DSD. This form of utility function generates aHausman). This type of utility model is commonplace amongversus Diminishing Marginal Utility References Burt, O.R.

  2. Optimized planning target volume margin in helical tomotherapy for prostate cancer: is there a preferred method?

    E-Print Network [OSTI]

    Cao, Yuan Jie; Chang, Kyung Hwan; Shim, Jang Bo; Kim, Kwang Hyeon; Jang, Min Sun; Yoon, Won Sup; Yang, Dae Sik; Park, Young Je; Kim, Chul Yong

    2015-01-01

    To compare the dosimetrical differences between plans generated by helical tomotherapy using 2D or 3D margining technique in in prostate cancer. Ten prostate cancer patients were included in this study. For 2D plans, planning target volume (PTV) was created by adding 5 mm (lateral/anterior-posterior) to clinical target volume (CTV). For 3D plans, 5 mm margin was added not only in lateral/anterior-posterior, but also in superior-inferior to CTV. Various dosimetrical indices, including the prescription isodose to target volume (PITV) ratio, conformity index (CI), homogeneity index (HI), target coverage index (TCI), modified dose homogeneity index (MHI), conformation number (CN), critical organ scoring index (COSI), and quality factor (QF) were determined to compare the different treatment plans. Differences between 2D and 3D PTV indices were not significant except for CI (p = 0.023). 3D margin plans (11195 MUs) resulted in higher (13.0%) monitor units than 2D margin plans (9728 MUs). There were no significant d...

  3. BUFFERED WELL FIELD OUTLINES

    U.S. Energy Information Administration (EIA) Indexed Site

    OIL & GAS FIELD OUTLINES FROM BUFFERED WELLS The VBA Code below builds oil & gas field boundary outlines (polygons) from buffered wells (points). Input well points layer must be a...

  4. Integrating Safety Assessment Methods using the Risk Informed Safety Margins Characterization (RISMC) Approach

    SciTech Connect (OSTI)

    Curtis Smith; Diego Mandelli

    2013-03-01

    Safety is central to the design, licensing, operation, and economics of nuclear power plants (NPPs). As the current light water reactor (LWR) NPPs age beyond 60 years, there are possibilities for increased frequency of systems, structures, and components (SSC) degradations or failures that initiate safety significant events, reduce existing accident mitigation capabilities, or create new failure modes. Plant designers commonly “over-design” portions of NPPs and provide robustness in the form of redundant and diverse engineered safety features to ensure that, even in the case of well-beyond design basis scenarios, public health and safety will be protected with a very high degree of assurance. This form of defense-in-depth is a reasoned response to uncertainties and is often referred to generically as “safety margin.” Historically, specific safety margin provisions have been formulated primarily based on engineering judgment backed by a set of conservative engineering calculations. The ability to better characterize and quantify safety margin is important to improved decision making about LWR design, operation, and plant life extension. A systematic approach to characterization of safety margins and the subsequent margin management options represents a vital input to the licensee and regulatory analysis and decision making that will be involved. In addition, as research and development (R&D) in the LWR Sustainability (LWRS) Program and other collaborative efforts yield new data, sensors, and improved scientific understanding of physical processes that govern the aging and degradation of plant SSCs needs and opportunities to better optimize plant safety and performance will become known. To support decision making related to economics, readability, and safety, the RISMC Pathway provides methods and tools that enable mitigation options known as margins management strategies. The purpose of the RISMC Pathway R&D is to support plant decisions for risk-informed margin management with the aim to improve economics, reliability, and sustain safety of current NPPs. As the lead Department of Energy (DOE) Laboratory for this Pathway, the Idaho National Laboratory (INL) is tasked with developing and deploying methods and tools that support the quantification and management of safety margin and uncertainty.

  5. Thermal well-test method

    DOE Patents [OSTI]

    Tsang, C.F.; Doughty, C.A.

    1984-02-24

    A well-test method involving injection of hot (or cold) water into a groundwater aquifer, or injecting cold water into a geothermal reservoir is disclosed. By making temperature measurements at various depths in one or more observation wells, certain properties of the aquifer are determined. These properties, not obtainable from conventional well test procedures, include the permeability anisotropy, and layering in the aquifer, and in-situ thermal properties. The temperature measurements at various depths are obtained from thermistors mounted in the observation wells.

  6. Assessment of Biomass Resources from Marginal Lands in APEC Economies

    SciTech Connect (OSTI)

    Milbrandt, A.; Overend, R. P.

    2009-08-01

    The goal of this study is to examine the marginal lands in Asia-Pacific Economic Cooperation (APEC) economies and evaluate their biomass productivity potential. Twelve categories of marginal lands are identified using the Global Agro-Ecological Zones system of the United Nations Food and Agriculture Organization.

  7. A risk-informed approach to safety margins analysis

    SciTech Connect (OSTI)

    Curtis Smith; Diego Mandelli

    2013-07-01

    The Risk Informed Safety Margins Characterization (RISMC) Pathway is a systematic approach developed to characterize and quantify safety margins of nuclear power plant structures, systems and components. The model has been tested on the Advanced Test Reactor (ATR) at Idaho National Lab.

  8. Kimberly Well - Photos

    SciTech Connect (OSTI)

    Shervais, John

    2011-06-16

    The Snake River Plain (SRP), Idaho, hosts potential geothermal resources due to elevated groundwater temperatures associated with the thermal anomaly Yellowstone-Snake River hotspot. Project HOTSPOT has coordinated international institutions and organizations to understand subsurface stratigraphy and assess geothermal potential. Over 5.9km of core were drilled from three boreholes within the SRP in an attempt to acquire continuous core documenting the volcanic and sedimentary record of the hotspot: (1) Kimama, (2) Kimberly, and (3) Mountain Home. The Kimberly drill hole was selected to document continuous volcanism when analysed in conjunction with the Kimama and is located near the margin of the plain. Data submitted by project collaborator Doug Schmitt, University of Alberta

  9. Continental margin architecture : sea level and climate

    E-Print Network [OSTI]

    Hill, Jenna Catherine

    2007-01-01

    N. W. , 1995. Sequence Stratigraphy. Annual Review of Earthinterpretation utilizing sequence stratigraphy, In: Bally,D. , 1990. Siliciclastic sequence stratigraphy in well logs,

  10. Surface expression of eastern Mediterranean slab dynamics: Neogene topographic and structural evolution of the southwest margin of the Central Anatolian Plateau, Turkey

    E-Print Network [OSTI]

    Schildgen, T. F.

    he southwest margin of the Central Anatolian Plateau has experienced multiple phases of topographic growth, including the formation of localized highs prior to the Late Miocene that were later affected by wholesale uplift ...

  11. Marginal erg facies: A trial approach toward a descriptive classification

    SciTech Connect (OSTI)

    Caputo, M.V. ); Langford, R.P. )

    1991-03-01

    During the late 1970s and early 1980s, sedimentologists began recognizing the margins of eolian sand seas as separate, components which differed from interior sand seas in geometry, extent, and facies. Stratigraphers have now observed these differences in eolian rocks. Erg margins may be grouped in five ways: (1) by associations with extradunal environments-coastal plain, lacustrine, periglacial, marine (tidal flat, coastal sabkha, beach, and lagoon), and arid alluvial (alluvial fan, fluvial, playa, inland sabkha); (2) by allocyclic controls-eustasy, plate tectonism, and climate; (3) by autocyclic controls-local tectonism, topography, vegetation, hydrology, structure, sediment source and supply, and wind regime; (4) by geographic position-upwind, downwind, and along-wind margins; and (5) by sedimentary facies-texture and architecture. In contrast with erg interiors, erg margins are characterized by smaller, less complex dune-forms related to thinner sand accumulation; elementary dune architecture; more vegetation and bioturbation; high occurrence of sand sheet, zibar, and serir facies; expansive, low-relief interdunes with widely distributed dunes; and a greater proportion of interbedded extradunal deposits. Some of the published studies on ancient eolian systems have identified erg margin facies that have been influences by marine and arid alluvial processes. Few reports have described lacustrine-eolian and periglacial-eolian interactions. This study is an attempt to organize known features of modern and ancient erg margins into a scheme based on erg margin controls.

  12. Global-local Structural Optimization Using Response Surfaces of Local Optimization Margins

    E-Print Network [OSTI]

    Neumaier, Arnold

    1 Global-local Structural Optimization Using Response Surfaces of Local Optimization Margins Boyang optimization problems. First, a large number of component optimizations for maximization of margins are performed. Response surface approximations (RSA) for maximum margins of component optimization

  13. Design of miniature floating platform for marginal fields

    E-Print Network [OSTI]

    Miao, Sha, S.M. Massachusetts Institute of Technology

    2013-01-01

    This thesis presents the design of a novel type of miniature floating offshore platforms with a heave plate attached at the keel, suitable for developing deep-water marginal fields. This design features a small displacement, ...

  14. Making In-Class Competitions Desirable For Marginalized Groups

    E-Print Network [OSTI]

    McGovern, Amy

    with and hinder other opponents (e.g. a stock car race or boxing match). Students using Spacewar were com- peting may also appeal other groups of students who can be marginalized in engineering. Our results indicate

  15. Geotechnical characterization of sediments from Hydrate Ridge, Cascadia Continental Margin

    E-Print Network [OSTI]

    Tan, Brian B. (Brian Bautista), 1979-

    2004-01-01

    Eight whole core sediment samples were obtained from ODP Site 1244, Hydrate Ridge, Cascadia Continental Margin with the goal of understanding the stress history, consolidation behavior and strength characteristics of the ...

  16. Plugging Abandoned Water Wells 

    E-Print Network [OSTI]

    Lesikar, Bruce J.

    2002-02-28

    is abandoned without proper plugging, upward flow of salty water from the deeper aquifer may cause contamination of the shallow, fresh water aquifer. Also, any pollu- tants that occur in one zone can migrate to another zone through a well. Unplugged abandoned... wells may deplete pres- sure within an aquifer. Pressure in artesian aquifers decreases as water discharges at land surface or to less pressurized aquifers. Eventually a drop in pres- sure causes flowing wells to stop flowing and the water level...

  17. The value of marginal analysis in electric power system operations

    SciTech Connect (OSTI)

    Katzman, M.T.; Shelton, R.B.

    1989-01-01

    Electric utilities have traditionally based their calculation of costs and derived prices on the basis of averages. Marginal analysis provides an alternative method of costing and price setting. Not only does marginal analysis yield different computations, it can lead to different and more efficient decisions. This point is illustrated by the evaluation of biomass cogeneration to a utility and the costing of rural extensions. 7 refs., 3 figs., 3 tabs.

  18. Electricity Prices in a Competitive Environment: Marginal Cost Pricing

    Reports and Publications (EIA)

    1997-01-01

    Presents the results of an analysis that focuses on two questions: (1) How are prices for competitive generation services likely to differ from regulated prices if competitive prices are based on marginal costs rather than regulated cost-of-service pricing? (2) What impacts will the competitive pricing of generation services (based on marginal costs) have on electricity consumption patterns, production costs, and the financial integrity of electricity suppliers?

  19. Project Overview and Motivation Given the burgeoning interest in the Cascadia margin from a variety of NSF-supported

    E-Print Network [OSTI]

    Holbrook, W. Steven

    accessible to the Langseth seismic system on the margin, (3) well-constrained site selection for the future 3D MCS box, (4) a timely "test run" of the open-participation, open-access model for Langseth to the lack of such regional 2-D data. Finally, the sole research vessel capable of completing this work

  20. On the marginal instability threshold condition of the aperiodic ordinary mode

    SciTech Connect (OSTI)

    Schlickeiser, R.; Yoon, P. H.

    2014-07-15

    The purely growing ordinary (O) mode instability has recently received renewed attention owing to its potential applicability to the solar wind plasma. Here, an analytical marginal instability condition is derived for counter-streaming bi-Maxwellian plasma particle distribution functions. The derived marginal instability condition as a function of the temperature anisotropy and plasma beta agrees remarkably well with the numerically determined instability condition. The existence of a new instability domain of the O-mode at small plasma beta values is confirmed with the leading A??{sub ?}{sup ?1}-dependence, if the counter-stream parameter P{sub e} exceeds a critical value. At small plasma beta values at large enough counter-stream parameter, the O-mode also operates for temperature anisotropies A?=?T{sub ?}/T{sub ?}?>?1 even larger than unity, as the parallel counter-stream free energy exceeds the perpendicular bi-Maxwellian free energy.

  1. Transverse extension of Guatemala active margin: implications for accretion

    SciTech Connect (OSTI)

    McMillen, K.J.

    1987-05-01

    The inner trench wall of the Middle America Trench off Guatemala does not show evidence of accretion, based on DSDP Legs 67 and 84. The presence of normal faults on the lower inner trench slope has resulted in various subsidence models for the margin. Fault traces would be expected to trend parallel to the margin (northwest-southeast) if margin subsidence had occurred. Instead, the faults trend north-south and occur in groups of faults downdropped to the east and to the west. The faults do not seem to be related to margin subsidence but rather to previously proposed Cenozoic Central American rifting. The rifting resulted from crustal bending as the Central American block rounded southern Mexico during differential North American/Caribbean plate motion. The rifts, which extend nearly to the trench axis, underlie the San Jose submarine canyon and align with the Guatemala City graben. Possible east-west accommodation zones, between fault zones that dip in opposite directions, exist near the shelf edge. These accommodation zones may have formed along lines of weakness where oceanic crust was previously emplaced into the margin during or prior to the Eocene. These rifts show that compressional and extension features can occur simultaneously with underthrusting on active margins.

  2. Penrose Well Temperatures

    SciTech Connect (OSTI)

    Christopherson, Karen

    2013-03-15

    Penrose Well Temperatures Geothermal waters have been encountered in several wells near Penrose in Fremont County, Colorado. Most of the wells were drilled for oil and gas exploration and, in a few cases, production. This ESRI point shapefile utilizes data from 95 wells in and around the Penrose area provided by the Colorado Oil and Gas Conservation Commission (COGCC) database at http://cogcc.state.co.us/ . Temperature data from the database were used to calculate a temperature gradient for each well. This information was then used to estimate temperatures at various depths. Projection: UTM Zone 13 NAD27 Extent: West -105.224871 East -105.027633 North 38.486269 South 38.259507 Originators: Colorado Oil and Gas Conservation Commission (COGCC) Karen Christopherson

  3. Bed radar reflectivity across the north margin of Whillans Ice Stream, West Antarctica, and implications for margin processes

    E-Print Network [OSTI]

    Raymond, C. F.; Catania, Ginny A.; Nereson, Nadine; van der Veen, Cornelis J.

    2006-01-01

    the margin is mediated by processes other than deformation of thick dilated till that is the source of lubrication allowing fast motion in the interior of the ice stream....

  4. Marginal Abatement Costs and Marginal Welfare Costs for Greenhouse Gas Emissions Reductions: Results from the EPPA Model

    E-Print Network [OSTI]

    Morris, Jennifer

    Marginal abatement cost (MAC) curves, relationships between tons of emissions abated and the CO2 (or GHG) price, have been widely used as pedagogic devices to illustrate simple economic concepts such as the benefits of ...

  5. Margin Size is an Independent Predictor of Local Tumor Progression After Ablation of Colon Cancer Liver Metastases

    SciTech Connect (OSTI)

    Wang Xiaodong; Sofocleous, Constantinos T., E-mail: sofoclec@mskcc.org; Erinjeri, Joseph P.; Petre, Elena N. [Memorial Sloan-Kettering Cancer Center, Section of Interventional Radiology, Department of Radiology (United States)] [Memorial Sloan-Kettering Cancer Center, Section of Interventional Radiology, Department of Radiology (United States); Gonen, Mithat [Memorial Sloan-Kettering Cancer Center, Department of Epidemiology and Biostatistics (United States)] [Memorial Sloan-Kettering Cancer Center, Department of Epidemiology and Biostatistics (United States); Do, Kinh G. [Memorial Sloan-Kettering Cancer Center, Department of Radiology (United States)] [Memorial Sloan-Kettering Cancer Center, Department of Radiology (United States); Brown, Karen T.; Covey, Anne M.; Brody, Lynn A.; Alago, William; Thornton, Raymond H. [Memorial Sloan-Kettering Cancer Center, Section of Interventional Radiology, Department of Radiology (United States)] [Memorial Sloan-Kettering Cancer Center, Section of Interventional Radiology, Department of Radiology (United States); Kemeny, Nancy E. [Memorial Sloan-Kettering Cancer Center, Department of Medicine (United States)] [Memorial Sloan-Kettering Cancer Center, Department of Medicine (United States); Solomon, Stephen B. [Memorial Sloan-Kettering Cancer Center, Section of Interventional Radiology, Department of Radiology (United States)] [Memorial Sloan-Kettering Cancer Center, Section of Interventional Radiology, Department of Radiology (United States)

    2013-02-15

    This study was designed to evaluate the relationship between the minimal margin size and local tumor progression (LTP) following CT-guided radiofrequency ablation (RFA) of colorectal cancer liver metastases (CLM). An institutional review board-approved, HIPPA-compliant review identified 73 patients with 94 previously untreated CLM that underwent RFA between March 2003 and May 2010, resulting in an ablation zone completely covering the tumor 4-8 weeks after RFA dynamic CT. Comparing the pre- with the post-RFA CT, the minimal margin size was categorized to 0, 1-5, 6-10, and 11-15 mm. Follow-up included CT every 2-4 months. Kaplan-Meier methodology and Cox regression analysis were used to evaluate the effect of the minimal margin size, tumor location, size, and proximity to a vessel on LTP. Forty-five of 94 (47.9 %) CLM progressed locally. Median LTP-free survival (LPFS) was 16 months. Two-year LPFS rates for ablated CLM with minimal margin of 0, 1-5 mm, 6-10 mm, 11-15 mm were 26, 46, 74, and 80 % (p < 0.011). Minimal margin (p = 0.002) and tumor size (p = 0.028) were independent risk factors for LTP. The risk for LTP decreased by 46 % for each 5-mm increase in minimal margin size, whereas each additional 5-mm increase in tumor size increased the risk of LTP by 22 %. An ablation zone with a minimal margin uniformly larger than 5 mm 4-8 weeks postablation CT is associated with the best local tumor control.

  6. Geothermal Well Site Restoration and Plug and Abandonment of Wells

    SciTech Connect (OSTI)

    Rinehart, Ben N.

    1994-08-01

    A report is presented on the final phase of an energy research program conducted by the U.S. Department of Energy (DOE) involving two geothermal well sites in the State of Louisiana-the Gladys McCall site and the Willis Hulin site. The research program was intended to improve geothermal technology and to determine the efficacy of producing electricity commercially from geopressured resource sites. The final phase of the program consisted of plug and abandonment (P&A) of the wells and restoration of the well sites. Restoration involved (a) initial soil and water sampling and analysis; (b) removal and disposal of well pads, concrete, utility poles, and trash; (c) plugging of monitor and freshwater wells; and (d) site leveling and general cleanup. Restoration of the McCall site required removal of naturally occurring radioactive material (NORM), which was costly and time-consuming. Exhibits are included that provide copies of work permits and authorizations, P&A reports and procedures, daily workover and current conditions report, and cost and salvage reports. Site locations, grid maps, and photographs are provided.

  7. Page 34 MARGINS Newsletter No. 9, Fall 2002 Towards a Data Management Infrastructure for MARGINS: Examples from

    E-Print Network [OSTI]

    Wright, Dawn Jeannine

    : Examples from Boomerang 8 and the Virtual Research Vessel Dawn J. Wright Department of Geosciences, Oregon- sues concerning the origin and structure of the Tonga forearc and trench includ- ing: (1) testing sites, as well as a comprehensive dredging program. The resulting web site is very simple by today

  8. Countries Gasoline Prices Including Taxes

    Gasoline and Diesel Fuel Update (EIA)

    Crude oil, gasoline, heating oil, diesel, propane, and other liquids including biofuels and natural gas liquids. Natural Gas Exploration and reserves, storage, imports and...

  9. Phenomenal well-being 

    E-Print Network [OSTI]

    Campbell, Stephen Michael

    2006-08-16

    the hedonistic concept of satisfaction. An epistemic model of life-comparison (inspired by Peter RailtonÂ?s full information account of well-being) on which phenomenal lives are judged on the criterion of satisfaction is presented, followed by some objections...

  10. Bioenergy crop productivity and potential climate change mitigation from marginal lands in the United States: An

    E-Print Network [OSTI]

    Zhuang, Qianlai

    ÀChampaign, Urbana, IL 61801, USA Abstract Growing biomass feedstocks from marginal lands is becoming an increasingly

  11. State discrimination with error margin and its locality

    E-Print Network [OSTI]

    A. Hayashi; T. Hashimoto; M. Horibe

    2008-07-10

    There are two common settings in a quantum-state discrimination problem. One is minimum-error discrimination where a wrong guess (error) is allowed and the discrimination success probability is maximized. The other is unambiguous discrimination where errors are not allowed but the inconclusive result "I don't know" is possible. We investigate discrimination problem with a finite margin imposed on the error probability. The two common settings correspond to the error margins 1 and 0. For arbitrary error margin, we determine the optimal discrimination probability for two pure states with equal occurrence probabilities. We also consider the case where the states to be discriminated are multipartite, and show that the optimal discrimination probability can be achieved by local operations and classical communication.

  12. Neutralino relic density including coannihilations

    E-Print Network [OSTI]

    Paolo Gondolo; Joakim Edsjo

    1997-11-25

    We give an overview of our precise calculation of the relic density of the lightest neutralino, in which we included relativistic Boltzmann averaging, subthreshold and resonant annihilations, and coannihilation processes with charginos and neutralinos.

  13. RADIO EMISSION FROM INSTABILITIES IN SPACE PLASMAS: MARGINAL STABILITY,

    E-Print Network [OSTI]

    Melrose, Don

    I t RADIO EMISSION FROM INSTABILITIES IN SPACE PLASMAS: MARGINAL STABILITY, 4TOCHASTIC GROWTH emission, hich is an indirect emission process first discussed by Ginaburg and Zhe/eznyakoe, 9581, and electron cyclotron maser emission (ECME), which is a direct emission ess first discussed in the presently

  14. Large Margin Taxonomy Embedding with an Application to Document Categorization

    E-Print Network [OSTI]

    Weinberger, Kilian

    Large Margin Taxonomy Embedding with an Application to Document Categorization Kilian Weinberger that the topics are not just discrete classes, but are nodes in a complex taxonomy with rich inter-topic relationships. For example, web pages can be categorized into the Yahoo! web taxonomy or medical journals can

  15. Derivation of Locational Marginal Prices for Restructured Wholesale Power Markets

    E-Print Network [OSTI]

    Tesfatsion, Leigh

    the performance of these markets. In this paper, different AC and DC optimal power flow (OPF) models are presented Operator (MISO). Keywords: Locational marginal pricing, wholesale power market, AC optimal power flow, DC optimal power flow, U.S. Midwest Independent System Operator (MISO). #12;3 1 INTRODUCTION In an April 2003

  16. The Marginalized Particle Filter for Automotive Tracking Applications

    E-Print Network [OSTI]

    Gustafsson, Fredrik

    1 The Marginalized Particle Filter for Automotive Tracking Applications Andreas Eidehall Thomas Sch surroundings (lane geometry and the position of other vehicles), which is needed for intelligent automotive in a nonlinear estimation problem. For automotive tracking systems, these problems are traditionally handled

  17. The Marginalized Particle Filter for Automotive Tracking Applications

    E-Print Network [OSTI]

    Schön, Thomas

    The Marginalized Particle Filter for Automotive Tracking Applications Andreas Eidehall Thomas B surroundings (lane geometry and the position of other vehicles), which is needed for intelligent automotive in a nonlinear estimation problem. For automotive tracking systems, these problems are traditionally handled

  18. Sustainable bioenergy production from marginal lands in the US Midwest

    SciTech Connect (OSTI)

    Gelfand, Ilya; Sahajpal, Ritvik; Zhang, Xuesong; Izaurralde, Roberto C.; Gross, Katherine L.; Robertson, G. P.

    2013-01-24

    Long-term measurements of global warming impact coupled with spatially explicit modeling suggests that both climate benefits and the production potential of cellulosic crops grown on marginal lands of the US North Central region are substantial but will be insufficient to meet long-term biofuel needs.

  19. Building a "Margin of Safety" Into Renewable Energy

    E-Print Network [OSTI]

    Building a "Margin of Safety" Into Renewable Energy Procurements: A Review of Experience purchasers and electricity regulators must confront the reality that signed renewable energy contracts will not always yield operational projects on the timeline given in the contracts themselves. Renewable energy

  20. Tectonic evolution of the southwestern Black Sea margin, offshore Turkey 

    E-Print Network [OSTI]

    Can, Emrah

    1996-01-01

    to the Srednogorie intra-arc zone in Bulgaria. Following back-arc extension, the whole margin was affected by a compressional tectonic regime during Paleocene-early Eocene time. Under this regime, a series of thrust faults formed, which were connected to the Stara...

  1. Acoustic well cleaner

    DOE Patents [OSTI]

    Maki, Jr., Voldi E. (11904 Bell Ave., Austin, TX 78759-2415); Sharma, Mukul M. (Dept. of Petroleum Engr. Univ. of Texas, Austin, TX 78712)

    1997-01-21

    A method and apparatus are disclosed for cleaning the wellbore and the near wellbore region. A sonde is provided which is adapted to be lowered into a borehole and which includes a plurality of acoustic transducers arranged around the sonde. Electrical power provided by a cable is converted to acoustic energy. The high intensity acoustic energy directed to the borehole wall and into the near wellbore region, redissolves or resuspends the material which is reducing the permeability of the formation and/or restricting flow in the wellbore.

  2. Altering Reservoir Wettability to Improve Production from Single Wells

    SciTech Connect (OSTI)

    W. W. Weiss

    2006-09-30

    Many carbonate reservoirs are naturally fractured and typically produce less than 10% original oil in place during primary recovery. Spontaneous imbibition has proven an important mechanism for oil recovery from fractured reservoirs, which are usually weak waterflood candidates. In some situations, chemical stimulation can promote imbibition of water to alter the reservoir wettability toward water-wetness such that oil is produced at an economic rate from the rock matrix into fractures. In this project, cores and fluids from five reservoirs were used in laboratory tests: the San Andres formation (Fuhrman Masho and Eagle Creek fields) in the Permian Basin of Texas and New Mexico; and the Interlake, Stony Mountain, and Red River formations from the Cedar Creek Anticline in Montana and South Dakota. Solutions of nonionic, anionic, and amphoteric surfactants with formation water were used to promote waterwetness. Some Fuhrman Masho cores soaked in surfactant solution had improved oil recovery up to 38%. Most Eagle Creek cores did not respond to any of the tested surfactants. Some Cedar Creek anticline cores had good response to two anionic surfactants (CD 128 and A246L). The results indicate that cores with higher permeability responded better to the surfactants. The increased recovery is mainly ascribed to increased water-wetness. It is suspected that rock mineralogy is also an important factor. The laboratory work generated three field tests of the surfactant soak process in the West Fuhrman Masho San Andres Unit. The flawlessly designed tests included mechanical well clean out, installation of new pumps, and daily well tests before and after the treatments. Treatments were designed using artificial intelligence (AI) correlations developed from 23 previous surfactant soak treatments. The treatments were conducted during the last quarter of 2006. One of the wells produced a marginal volume of incremental oil through October. It is interesting to note that the field tests were conducted in an area of the field that has not met production expectations. The dataset on the 23 Phosphoria well surfactant soaks was updated. An analysis of the oil decline curves indicted that 4.5 lb of chemical produced a barrel of incremental oil. The AI analysis supports the adage 'good wells are the best candidates.' The generally better performance of surfactant in the high permeability core laboratory tests supports this observation. AI correlations were developed to predict the response to water-frac stimulations in a tight San Andres reservoir. The correlations maybe useful in the design of Cedar Creek Anticline surfactant soak treatments planned for next year. Nuclear Magnetic Resonance scans of dolomite cores to measure porosity and saturation during the high temperature laboratory work were acquired. The scans could not be correlated with physical measurement using either conventional or AI methods.

  3. Development Wells At Salt Wells Area (Nevada Bureau of Mines...

    Open Energy Info (EERE)

    Development Wells At Salt Wells Area (Nevada Bureau of Mines and Geology, 2009) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Development Wells...

  4. Victorian Queer: Marginality and Money in Nineteenth-Century Literature 

    E-Print Network [OSTI]

    Choi, Jung Sun

    2013-05-01

    , in that their voices are taken to be insignificant, and they are constantly queered even by the marginal group. In his book Enforcing Normalcy: Disability, Deafness and the Body, Lennard J. Davis focuses on the word ?normal? to understand the historical process... and problems that society and culture have faced. He defines a group of chosen words, called ?Keywords,? as ?significant indicative words in certain forms of thought? and ?certain uses [of these words] bound together certain ways of seeing culture and society...

  5. Single-Well and Cross-Well Seismic At Salt Wells Area (Bureau...

    Open Energy Info (EERE)

    Single-Well and Cross-Well Seismic At Salt Wells Area (Bureau of Land Management, 2009) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity:...

  6. R E V I E W Functionality and the evolution of marginal stability in proteins

    E-Print Network [OSTI]

    Pollock, David

    R E V I E W Functionality and the evolution of marginal stability in proteins: Inferences from proteins are marginally stable. This has inspired several explanations. Having noted that the functionality that marginally stable proteins should have an evolutionary advantage over proteins of differing stability. Others

  7. Passive margins getting squeezed in the mantle convection vice Philippe Yamato,1

    E-Print Network [OSTI]

    Becker, Thorsten W.

    Passive margins getting squeezed in the mantle convection vice Philippe Yamato,1 Laurent Husson,1 2013. [1] Passive margins often exhibit uplift, exhumation, and tectonic inversion. We speculate passive margins. In order to address this issue, we design a 2-D viscous numerical model wherein

  8. Simple Model of Membrane Proteins Including Solvent

    E-Print Network [OSTI]

    D. L. Pagan; A. Shiryayev; T. P. Connor; J. D. Gunton

    2006-03-04

    We report a numerical simulation for the phase diagram of a simple two dimensional model, similar to one proposed by Noro and Frenkel [J. Chem. Phys. \\textbf{114}, 2477 (2001)] for membrane proteins, but one that includes the role of the solvent. We first use Gibbs ensemble Monte Caro simulations to determine the phase behavior of particles interacting via a square-well potential in two dimensions for various values of the interaction range. A phenomenological model for the solute-solvent interactions is then studied to understand how the fluid-fluid coexistence curve is modified by solute-solvent interactions. It is shown that such a model can yield systems with liquid-liquid phase separation curves that have both upper and lower critical points, as well as closed loop phase diagrams, as is the case with the corresponding three dimensional model.

  9. Risk-Informed Safety Margin Characterization Case Study: Selection of Electrical Equipment to Be Subjected to Environmental Qualification

    SciTech Connect (OSTI)

    D. P. Blanchard; R. W. Youngblood

    2014-06-01

    The Risk-Informed Safety Margin Characterization (RISMC) pathway of the DOE’s Light Water Reactor Sustainability (LWRS) program focuses on advancing the state of the art in safety analysis and risk assessment to support decision-making on nuclear power plant operation well beyond the originally designed lifetime of the plants (i.e., beyond 60 years). Among the issues being addressed in RISMC is the significance of SSC aging and how confident we are about our understanding of its impact on the margin between the loads SSCs are expected to see during normal operation and accident conditions, and the SSC capacities (their ability to resist those loads) as the SSCs age. In this paper, a summary is provided of a case study that examines SSC aging from an environmental qualification (EQ) perspective. The case study illustrates how the state of knowledge regarding SSC margin can be characterized given the overall integrated plant design, and was developed to demonstrate a method for deciding on which cables to focus, which cables are not so important from an environmental qualification margin standpoint, and what plant design features or operating characteristics determine the role that environmental qualification plays in establishing a safety case on which decisions regarding margin can be made. The selection of cables for which demonstration of margin with respect to aging and environmental challenges uses a technique known as Prevention Analysis. Prevention Analysis is a Boolean method for optimal selection of SSCs (that is, those combinations of SSCs both necessary and sufficient to meet a predetermined selection criterion) in a manner that allows demonstration that plant-level safety can be demonstrated by the collection of selected SSCs alone. Choosing the set of SSCs that is necessary and sufficient to satisfy the safety objectives, and demonstrating that the safety objectives can be met effectively, determines where resources are best allocated to assure SSC performance margin. The paper describes the resulting component types that were selected by Prevention Analysis and identifies the accident sequence characteristics that cause these component types to be important from an EQ and aging perspective (and, hence, worthwhile evaluating the extent of safety margin). In addition, component types not selected as needing significant margin from an EQ and aging perspective are discussed and an engineering rationale is developed justifying the lack of need to apply resources to demonstrating margin for these component types. This rationale is in terms of design features of the plant and operating characteristics that make these component types less important from an EQ and aging perspective. While the case study focuses on EQ and aging of equipment and cables located inside the containment of this PWR, the prevention analysis method is demonstrated to be an effective technique for identification of minimal collections of components that would be effective in managing safety for a variety of issues associated with aging and long-term operation of the fleet of plants.

  10. Well-pump alignment system

    DOE Patents [OSTI]

    Drumheller, Douglas S. (Cedar Crest, NM)

    1998-01-01

    An improved well-pump for geothermal wells, an alignment system for a well-pump, and to a method for aligning a rotor and stator within a well-pump, wherein the well-pump has a whistle assembly formed at a bottom portion thereof, such that variations in the frequency of the whistle, indicating misalignment, may be monitored during pumping.

  11. Light Water Reactor Sustainability Program Risk-Informed Safety Margins Characterization (RISMC) PathwayTechnical Program Plan

    SciTech Connect (OSTI)

    Curtis Smith; Cristian Rabiti; Richard Martineau

    2012-11-01

    Safety is central to the design, licensing, operation, and economics of Nuclear Power Plants (NPPs). As the current Light Water Reactor (LWR) NPPs age beyond 60 years, there are possibilities for increased frequency of Systems, Structures, and Components (SSCs) degradations or failures that initiate safety-significant events, reduce existing accident mitigation capabilities, or create new failure modes. Plant designers commonly “over-design” portions of NPPs and provide robustness in the form of redundant and diverse engineered safety features to ensure that, even in the case of well-beyond design basis scenarios, public health and safety will be protected with a very high degree of assurance. This form of defense-in-depth is a reasoned response to uncertainties and is often referred to generically as “safety margin.” Historically, specific safety margin provisions have been formulated, primarily based on “engineering judgment.”

  12. Carbonate depositional environments and facies of the shelf margin and outer shelf, Lower Cretaceous Sligo Formation, south Texas 

    E-Print Network [OSTI]

    Kirkland, Brenda Lee

    1986-01-01

    not been described in as much detail. Since the publication" of the facies study by Bebout et al. ( 1981), cores from two new wells along the reef trend have become available. A need exists for a detailed facies model along the shelf margin, for a... SLIGO 18. 48D R 15220 ft I SP I IIES 18, 800 fl TD AES j ( Q AES 16. 810 II TD ) ) I CORED INTERVAL ? TOP HOSSTON 18. 947 It TD 29 NUMBER OF SAMPLES OF EACH LiTHOLOG, ALL WELLS 60 NUMBER OF SAMPLES 20 pe @AC Gp, g( Z&qXO~ &~SXO~ C...

  13. Marginal Misses After Postoperative Intensity-Modulated Radiotherapy for Head and Neck Cancer

    SciTech Connect (OSTI)

    Chen, Allen M.; Farwell, D. Gregory; Luu, Quang; Chen, Leon M.; Vijayakumar, Srinivasan; Purdy, James A.

    2011-08-01

    Purpose: To describe the spatial distribution of local-regional recurrence (LRR) among patients treated postoperatively with intensity-modulated radiotherapy (IMRT) for head and neck cancer. Methods and Materials: The medical records of 90 consecutive patients treated by gross total resection and postoperative IMRT for squamous cell carcinoma of the head and neck from January 2003 to July 2009 were reviewed. Sites of disease were the oral cavity (43 patients), oropharynx (20 patients), larynx (15 patients), and hypopharynx (12 patients). Fifty patients (56%) received concurrent chemotherapy. Results: Seventeen of 90 patients treated with postoperative IMRT experienced LRR, yielding a 2-year estimate of local regional control of 80%. Among the LRR patients, 11 patients were classified as in-field recurrences, occurring within the physician-designated clinical target volume, and 6 patients were categorized as marginal recurrences. There were no out-of-field geographical misses. Sites of marginal LRRs included the contralateral neck adjacent to the spared parotid gland (3 patients), the dermal/subcutaneous surface (2 patients), and the retropharyngeal/retrostyloid lymph node region (1 patient). Conclusions: Although the incidence of geographical misses was relatively low, the possibility of this phenomenon should be considered in the design of target volumes among patients treated by postoperative IMRT for head and neck cancer.

  14. Negative margins and OPEC prices: how buyers and sellers are coping

    SciTech Connect (OSTI)

    Not Available

    1984-11-28

    Apparent refining margins are so poor that many US refiners have accelerated their destocking, waiting for market uncertainty to be resolved. Margins based on official OPEC prices continue to be virtually all negative, including very light oils from the Middle East; by now, up to half the world's oil trade may reflect spot marketing, compared to less than 10% a few years ago. In today's buyer's market for crude oil, several sellers are resorting to multi-faceted discounts amounting to as much as US $4.50 or more under official OPEC prices. But meanwhile, US oil importers have learned how not to rely so much on a traditional run of crude oil: they are running reduced crude, resid, cat feed, condensate; and they are blending components for lighter products by importing and swapping whenever even pennies per barrel can be saved. This issue presents: (1) refining netback data, US Gulf and West Coasts, late November 1984 (official/contract vs spot crude prices; (2) asphalt export prices to the US from Canada, N. Antilles, and Venezuela; and (3) the fuel price/tax series and industrial fuel prices as of October 1984 for countries of the Western Hemisphere.

  15. Dangerous Liouville Wave -- exactly marginal but non-conformal deformation

    E-Print Network [OSTI]

    Chiu Man Ho; Yu Nakayama

    2008-07-26

    We give a non-trivially interacting field theory example of scale invariant but non-conformal field theory. The model is based on the exactly solvable Liouville field theory coupled with free scalars deformed by an exactly marginal operator. We show non-vanishing of the trace of the energy-momentum tensor by using the quantum Schwinger-Dyson equation for the Liouville field theory, which is a sophistication of the quantum higher equations of motion for the Liouville field theory introduced by Alyosha Zamolodchikov. Possibly dangerous implications for the super-critical string theory will be discussed.

  16. #include #include

    E-Print Network [OSTI]

    Kessler, Christoph

    ] (where a[n] = +infty). C's * bsearch() can't be used, it requires a[j]==key. */ int findloc( void *key Combine­CRCW BSP­Quicksort * variant by Gerbessiotis/Valiant JPDC 22(1994) * implemented in NestStep­C. */ int N=10; // default value /** findloc(): find largest index j in [0..n­1] with * a[j

  17. Kimberly Well - Borehole Geophysics Database

    SciTech Connect (OSTI)

    Shervais, John

    2011-07-04

    The Snake River Plain (SRP), Idaho, hosts potential geothermal resources due to elevated groundwater temperatures associated with the thermal anomaly Yellowstone-Snake River hotspot. Project HOTSPOT has coordinated international institutions and organizations to understand subsurface stratigraphy and assess geothermal potential. Over 5.9km of core were drilled from three boreholes within the SRP in an attempt to acquire continuous core documenting the volcanic and sedimentary record of the hotspot: (1) Kimama, (2) Kimberly, and (3) Mountain Home. The Kimberly drill hole was selected to document continuous volcanism when analysed in conjunction with the Kimama and is located near the margin of the plain. Data submitted by project collaborator Doug Schmitt, University of Alberta

  18. SU-E-T-573: The Robustness of a Combined Margin Recipe for Uncertainties During Radiotherapy

    SciTech Connect (OSTI)

    Stroom, J; Vieira, S; Greco, C [Champalimaud Foundation, Lisbon, Lisbon (Portugal)

    2014-06-01

    Purpose: To investigate the variability of a safety margin recipe that combines CTV and PTV margins quadratically, with several tumor, treatment, and user related factors. Methods: Margin recipes were calculated by monte-carlo simulations in 5 steps. 1. A spherical tumor with or without isotropic microscopic was irradiated with a 5 field dose plan2. PTV: Geometric uncertainties were introduced using systematic (Sgeo) and random (sgeo) standard deviations. CTV: Microscopic disease distribution was modelled by semi-gaussian (Smicro) with varying number of islets (Ni)3. For a specific uncertainty set (Sgeo, sgeo, Smicro(Ni)), margins were varied until pre-defined decrease in TCP or dose coverage was fulfilled. 4. First, margin recipes were calculated for each of the three uncertainties separately. CTV and PTV recipes were then combined quadratically to yield a final recipe M(Sgeo, sgeo, Smicro(Ni)).5. The final M was verified by simultaneous simulations of the uncertainties.Now, M has been calculated for various changing parameters like margin criteria, penumbra steepness, islet radio-sensitivity, dose conformity, and number of fractions. We subsequently investigated A: whether the combined recipe still holds in all these situations, and B: what the margin variation was in all these cases. Results: We found that the accuracy of the combined margin recipes remains on average within 1mm for all situations, confirming the correctness of the quadratic addition. Depending on the specific parameter, margin factors could change such that margins change over 50%. Especially margin recipes based on TCP-criteria are more sensitive to more parameters than those based on purely geometric Dmin-criteria. Interestingly, measures taken to minimize treatment field sizes (by e.g. optimizing dose conformity) are counteracted by the requirement of larger margins to get the same tumor coverage. Conclusion: Margin recipes combining geometric and microscopic uncertainties quadratically are accurate under varying circumstances. However margins can change up to 50% for different situations.

  19. Well-pump alignment system

    DOE Patents [OSTI]

    Drumheller, D.S.

    1998-10-20

    An improved well-pump for geothermal wells, an alignment system for a well-pump, and to a method for aligning a rotor and stator within a well-pump are disclosed, wherein the well-pump has a whistle assembly formed at a bottom portion thereof, such that variations in the frequency of the whistle, indicating misalignment, may be monitored during pumping. 6 figs.

  20. Well constructions with inhibited microbial growth and methods of antimicrobial treatment in wells

    DOE Patents [OSTI]

    Lee, Brady D.; Dooley, Kirk J.

    2004-11-02

    The invention includes methods of inhibiting microbial growth in a well. A packing material containing a mixture of a first material and an antimicrobial agent is provided to at least partially fill a well bore. One or more access tubes are provided in an annular space around a casing within the well bore. The access tubes have a first terminal opening located at or above a ground surface and have a length that extends from the first terminal opening at least part of the depth of the well bore. The access tubes have a second terminal opening located within the well bore. An antimicrobial material is supplied into the well bore through the first terminal opening of the access tubes. The invention also includes well constructs.

  1. Health And Wellness Department Of Health And Wellness

    E-Print Network [OSTI]

    McConnell, Terry

    Health And Wellness Department Of Health And Wellness Lutchmie Narine, Chair, 315-443-9630 426 The Department of Health and Wellness offers a 123-credit Bachelor of Science degree (B.S.) in public health. Our graduates are prepared to work in community health education and health promotion in public health agencies

  2. Ultra Thin Quantum Well Materials

    SciTech Connect (OSTI)

    Dr Saeid Ghamaty

    2012-08-16

    This project has enabled Hi-Z technology Inc. (Hi-Z) to understand how to improve the thermoelectric properties of Si/SiGe Quantum Well Thermoelectric Materials. The research that was completed under this project has enabled Hi-Z Technology, Inc. (Hi-Z) to satisfy the project goal to understand how to improve thermoelectric conversion efficiency and reduce costs by fabricating ultra thin Si/SiGe quantum well (QW) materials and measuring their properties. In addition, Hi-Z gained critical new understanding on how thin film fabrication increases the silicon substrate's electrical conductivity, which is important new knowledge to develop critical material fabrication parameters. QW materials are constructed with alternate layers of an electrical conductor, SiGe and an electrical insulator, Si. Film thicknesses were varied, ranging from 2nm to 10nm where 10 nm was the original film thickness prior to this work. The optimum performance was determined at a Si and SiGe thickness of 4nm for an electrical current and heat flow parallel to the films, which was an important conclusion of this work. Essential new information was obtained on how the Si substrate electrical conductivity increases by up to an order of magnitude upon deposition of QW films. Test measurements and calculations are accurate and include both the quantum well and the substrate. The large increase in substrate electrical conductivity means that a larger portion of the electrical current passes through the substrate. The silicon substrate's increased electrical conductivity is due to inherent impurities and thermal donors which are activated during both molecular beam epitaxy and sputtering deposition of QW materials. Hi-Z's forward looking cost estimations based on future high performance QW modules, in which the best Seebeck coefficient and electrical resistivity are taken from separate samples predict that the electricity cost produced with a QW module could be achieved at <$0.35/W. This price would open many markets for waste heat recovery applications. By installing Hi-Z's materials in applications in which electricity could be produced from waste heat sources could result in significant energy savings as well as emissions reductions. For example, if QW thermoelectric generators could be introduced commercially in 2015, and assuming they could also capture an additional 0.1%/year of the available waste heat from the aluminum, steel, and iron industries, then by 2020, their use would lead to a 2.53 trillion Btu/year reduction in energy consumption. This translates to a $12.9 million/year energy savings, and 383.6 million lb's of CO2 emissions reduction per year. Additionally, Hi-Z would expect that the use of QW TE devices in the automotive, manufacturing, and energy generation industries would reduce the USA's petroleum and fossil fuel dependence, and thus significantly reduce emissions from CO2 and other polluting gasses such as NOx, SOx, and particulate matter (PM), etc.

  3. SU-F-BRD-09: Is It Sufficient to Use Only Low Density Tissue-Margin to Compensate Inter-Fractionation Setup Uncertainties in Lung Treatment?

    SciTech Connect (OSTI)

    Nie, K; Yue, N; Chen, T; Millevoi, R; Qin, S; Guo, J

    2014-06-15

    Purpose: In lung radiation treatment, PTV is formed with a margin around GTV (or CTV/ITV). Although GTV is most likely of water equivalent density, the PTV margin may be formed with the surrounding low-density tissues, which may lead to unreal dosimetric plan. This study is to evaluate whether the concern of dose calculation inside the PTV with only low density margin could be justified in lung treatment. Methods: Three SBRT cases were analyzed. The PTV from the original plan (Plan-O) was created with a 5–10 mm margin outside the ITV to incorporate setup errors and all mobility from 10 respiratory phases. Test plans were generated with the GTV shifted to the PTV edge to simulate the extreme situations with maximum setup uncertainties. Two representative positions as the very posterior-superior (Plan-PS) and anterior-inferior (Plan-AI) edge were considered. The virtual GTV was assigned a density of 1.0 g.cm?3 and surrounding lung, including the PTV margin, was defined as 0.25 g.cm?3. Also, additional plan with a 1mm tissue-margin instead of full lung-margin was created to evaluate whether a composite-margin (Plan-Comp) has a better approximation for dose calculation. All plans were generated on the average CT using Analytical Anisotropic Algorithm with heterogeneity correction on and all planning parameters/monitor unites remained unchanged. DVH analyses were performed for comparisons. Results: Despite the non-static dose distribution, the high-dose region synchronized with tumor positions. This might due to scatter conditions as greater doses were absorbed in the solid-tumor than in the surrounding low-density lungtissue. However, it still showed missing target coverage in general. Certain level of composite-margin might give better approximation for the dosecalculation. Conclusion: Our exploratory results suggest that with the lungmargin only, the planning dose of PTV might overestimate the coverage of the target during treatment. The significance of this overestimation might warrant further investigation.

  4. Assessment of Injection Well Construction and Operation for Water Injection Wells and Salt Water Disposal Wells

    E-Print Network [OSTI]

    such as drilling mud and work- over fluids. These are all shallow wells using injected fresh water to dissolve salt Disposal Wells in the Nine Township Area ­ 2009 September 2009 Prepared by Delaware Basin Drilling into a brine solution. In order to develop a solution mine, either a new well is drilled for brine extraction

  5. RECONSTRUCTING PALEO-SMT POSITIONS ON THE CASCADIA MARGIN USING MAGNETIC SUSCEPTIBILITY

    SciTech Connect (OSTI)

    Johnson, Joel; Phillips, Stephen

    2014-09-30

    Magnetic susceptibility (?) is a mixed signal in marine sediments, representing primary depositional and secondary diagenetic processes. Production of hydrogen sulfide via anaerobic oxidation of methane (AOM) at the sulfate-methane transition (SMT) and organoclastic sulfate reduction above the SMT can result in the dissolution of iron oxides, altering ? in sediments in methane gas and gas hydrate bearing regions. We investigated records of ? on the Cascadia margin (ODP Sites 1249 and 1252; IODP Site 1325) using a Zr/Rb heavy mineral proxy from XRF core scanning to identify intervals of primary detrital magnetic susceptibility and intervals and predict intervals affected by magnetite dissolutions. We also measured total sulfur content, grain size distributions, total organic carbon (TOC) content, and magnetic mineral assemblage. The upper 100 m of Site 1252 contains a short interval of ? driven by primary magnetite, with multiple intervals (> 90 m total) of decreased ? correlated with elevated sulfur content, consistent with dissolution of magnetite and re-precipitation of pyrite. In the upper 90 m of Site 1249, ? is almost entirely altered by diagenetic processes, with much of the low ? explained by a high degree of pyritization, and some intervals affected by the precipitation of magnetic iron sulfides. At Site 1325, ? between 0-20 and 51-73 mbsf represents primary mineralogy, and in the interval 24-51 mbsf, ? may be reduced due to pyritization. This integrated approach allows for a prediction of primary ? and the amount of ? loss at each site when compared to actual ? measurements. In the case of magnetite dissolution and full pyritization, these drawdowns in ? are supported by sulfur measurements, and the exposure times of magnetite to hydrogen sulfide can be modeled. The presence of methane and methane hydrates at these sites, as well as large variations in TOC content, suggest that the past migration rates of the SMT and variation in sulfate reduction rates may influence ? alteration along the Cascadia margin.

  6. Phytologia (December 2009) 91(3) 571 VARIATION AMONG THE SMOOTH-LEAF MARGINED

    E-Print Network [OSTI]

    Adams, Robert P.

    -coumarate: CoA Ligase, Abscisic acid-insensitive 3, petN, psbM, SNPs, taxonomy. The smooth-leaf margined

  7. "Do It Again": Comic Repetition, Participatory Reception and Gendered Identity on Musical Comedy's Margins

    E-Print Network [OSTI]

    Baltimore, Samuel Dworkin

    2013-01-01

    Oz Before the Rainbow. Baltimore: Johns Hopkins Universityby Samuel Dworkin Baltimore ABSTRACT OF THE DISSERTATION “DoMargins by Samuel Dworkin Baltimore Doctor of Philosophy in

  8. Treatment of Passive Component Reliability in Risk-Informed Safety Margin Characterization FY 2010 Report

    SciTech Connect (OSTI)

    Robert W Youngblood

    2010-09-01

    The Risk-Informed Safety Margin Characterization (RISMC) pathway is a set of activities defined under the U.S. Department of Energy (DOE) Light Water Reactor Sustainability Program. The overarching objective of RISMC is to support plant life-extension decision-making by providing a state-of-knowledge characterization of safety margins in key systems, structures, and components (SSCs). A technical challenge at the core of this effort is to establish the conceptual and technical feasibility of analyzing safety margin in a risk-informed way, which, unlike conventionally defined deterministic margin analysis, is founded on probabilistic characterizations of SSC performance.

  9. A margin based approach to determining sample sizes via tolerance bounds.

    SciTech Connect (OSTI)

    Newcomer, Justin T.; Freeland, Katherine Elizabeth

    2013-09-01

    This paper proposes a tolerance bound approach for determining sample sizes. With this new methodology we begin to think of sample size in the context of uncertainty exceeding margin. As the sample size decreases the uncertainty in the estimate of margin increases. This can be problematic when the margin is small and only a few units are available for testing. In this case there may be a true underlying positive margin to requirements but the uncertainty may be too large to conclude we have sufficient margin to those requirements with a high level of statistical confidence. Therefore, we provide a methodology for choosing a sample size large enough such that an estimated QMU uncertainty based on the tolerance bound approach will be smaller than the estimated margin (assuming there is positive margin). This ensures that the estimated tolerance bound will be within performance requirements and the tolerance ratio will be greater than one, supporting a conclusion that we have sufficient margin to the performance requirements. In addition, this paper explores the relationship between margin, uncertainty, and sample size and provides an approach and recommendations for quantifying risk when sample sizes are limited.

  10. Session: Long Valley Exploratory Well

    SciTech Connect (OSTI)

    Tennyson, George P. Jr.; Finger, John T.; Eichelberger, John C.; Hickox, Charles E.

    1992-01-01

    This session at the Geothermal Energy Program Review X: Geothermal Energy and the Utility Market consisted of four presentations: ''Long Valley Exploratory Well - Summary'' by George P. Tennyson, Jr.; ''The Long Valley Well - Phase II Operations'' by John T. Finger; ''Geologic results from the Long Valley Exploratory Well'' by John C. Eichelberger; and ''A Model for Large-Scale Thermal Convection in the Long Valley Geothermal Region'' by Charles E. Hickox.

  11. Well Monitoring System for EGS

    Broader source: Energy.gov [DOE]

    EGS well monitoring tools offer a unique set of solutions which will lower costs and increase confidence in future geothermal projects.

  12. Geothermal-Reservoir Well-Stimulation Program. Program status report

    SciTech Connect (OSTI)

    Not Available

    1982-05-01

    Seven experimental fracture stimulation treatments completed to date and the laboratory work performed to develop the stimulation technology are described. A discussion of the pre-stimulation and post-stimulation data and their evaluation is provided for each experiment. Six of the seven stimulation experiments were at least technically successful in stimulating the wells. The two fracture treatments in East Mesa 58-30 more than doubled the producing rate of the previously marginal producer. The two fracture treatments in Raft River and the two in Baca were all successful in obtaining significant production from previously nonproductive intervals. However, these treatments failed to establish commercial production due to deficiencies in either fluid temperature or flow rate. The acid etching treatment in the well at The Geysers did not have any material effect on producing rate.

  13. Optimization of fractured well performance of horizontal gas wells 

    E-Print Network [OSTI]

    Magalhaes, Fellipe Vieira

    2009-06-02

    In low-permeability gas reservoirs, horizontal wells have been used to increase the reservoir contact area, and hydraulic fracturing has been further extending the contact between wellbores and reservoirs. This thesis presents an approach...

  14. Prices include compostable serviceware and linen tablecloths

    E-Print Network [OSTI]

    California at Davis, University of

    APPETIZERS Prices include compostable serviceware and linen tablecloths for the food tables.ucdavis.edu. BUTTERNUT SQUASH & BLACK BEAN ENCHILADAS #12;BUFFETS Prices include compostable serviceware and linen

  15. Binary Join Trees for Computing Marginals in the Shenoy-Shafer Architecture

    E-Print Network [OSTI]

    Shenoy, Prakash P.

    1997-08-01

    -2003, USA pshenoy@ku.edu http://lark.cc.ku.edu/~pshenoy ? Appeared in International Journal of Approximate Reasoning, 17(2-3), 1997, 239?263. ii Binary Join Trees for Computing Marginals in the Shenoy... NETWORK FRAMEWORK .................................................2 3 AXIOMS FOR LOCAL COMPUTATION..........................................................5 4 COMPUTING A MARGINAL USING THE FUSION ALGORITHM ........................6 5 FUSION...

  16. Faunal responses to oxygen gradients on the Pakistan margin: A comparison of foraminiferans, macrofauna and megafauna

    E-Print Network [OSTI]

    Levin, Lisa

    Faunal responses to oxygen gradients on the Pakistan margin: A comparison of foraminiferans Oxygen minimum zone Benthos Arabian Sea Biodiversity Deep sea a b s t r a c t The Pakistan Margin where oxygen levels were lowest. The rarity of larger animals between 300 and 700 m on the Pakistan

  17. Wind speed influence on phytoplankton bloom dynamics in the Southern Ocean Marginal Ice Zone

    E-Print Network [OSTI]

    Moore, Keith

    Wind speed influence on phytoplankton bloom dynamics in the Southern Ocean Marginal Ice Zone Dillon; published 7 August 2007. [1] Analysis of satellite ocean color and wind speed data within the seasonal ice. Moore (2007), Wind speed influence on phytoplankton bloom dynamics in the Southern Ocean Marginal Ice

  18. Ranking Structured Documents: A Large Margin Based Approach for Patent Prior Art Search

    E-Print Network [OSTI]

    Gomes, Carla P.

    Ranking Structured Documents: A Large Margin Based Approach for Patent Prior Art Search Yunsong Guo propose an approach for automatically rank- ing structured documents applied to patent prior art search. Our model, SVM Patent Ranking (SVMP R) incorporates margin constraints that di- rectly capture

  19. From Camp Dwellers to Urban Refugees?: Urbanization and Marginalization of Refugee Camps in Lebanon.

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    - 1 - From Camp Dwellers to Urban Refugees?: Urbanization and Marginalization of Refugee Camps villes invisibles 1. Introduction Palestinian refugees in Lebanon are marginalized in their host society with the relationship between the refugees' own socio-political dynamic, political actors, and space. The migrations

  20. The Case for Increasing Enrollment and Leveraging Marginal Costs: CSUN Case Study

    E-Print Network [OSTI]

    Shubin, Carol

    The Case for Increasing Enrollment and Leveraging Marginal Costs: CSUN Case Study H. Hellenbrand1 will estimate the marginal cost for increasing enrollment from a theoretical point of view. This analysis will use data from the IPEDS data base and formulae for replacement costs suggested by the Legislative

  1. The Continental Margin is a Key Source of Iron to the HNLC North Pacific Ocean

    E-Print Network [OSTI]

    The Continental Margin is a Key Source of Iron to the HNLC North Pacific Ocean Phoebe J. Lam1 concentrations in the upper 500m of the Western Subarctic Pacific, an iron-limited High Nutrient Low Chlorophyll a key source of bioavailable Fe to the HNLC North Pacific. Keywords: iron, continental margin, HNLC 1

  2. Surface Indicators of Geothermal Activity at Salt Wells, Nevada...

    Open Energy Info (EERE)

    Surface Indicators of Geothermal Activity at Salt Wells, Nevada, USA, Including Warm Ground, Borate Deposits, and Siliceous Alteration Jump to: navigation, search OpenEI Reference...

  3. Well blowout rates in California Oil and Gas District 4--Update and Trends

    E-Print Network [OSTI]

    Benson, Sally M.

    2010-01-01

    fluid volume. Well construction includes drilling, reworkingTrends Table 3: Drilling Blowouts, Wells Drilled, Rates and1,11 As for well construction overall, the drilling blowout

  4. Well blowout rates in California Oil and Gas District 4--Update and Trends

    E-Print Network [OSTI]

    Benson, Sally M.

    2010-01-01

    Trends Table 3: Drilling Blowouts, Wells Drilled, Rates andfluid volume. Well construction includes drilling, reworking3 and 4. The drilling blowout rate per well from 1991 to

  5. Quantum well multijunction photovoltaic cell

    DOE Patents [OSTI]

    Chaffin, Roger J. (Albuquerque, NM); Osbourn, Gordon C. (Albuquerque, NM)

    1987-01-01

    A monolithic, quantum well, multilayer photovoltaic cell comprises a p-n junction comprising a p-region on one side and an n-region on the other side, each of which regions comprises a series of at least three semiconductor layers, all p-type in the p-region and all n-type in the n-region; each of said series of layers comprising alternating barrier and quantum well layers, each barrier layer comprising a semiconductor material having a first bandgap and each quantum well layer comprising a semiconductor material having a second bandgap when in bulk thickness which is narrower than said first bandgap, the barrier layers sandwiching each quantum well layer and each quantum well layer being sufficiently thin that the width of its bandgap is between said first and second bandgaps, such that radiation incident on said cell and above an energy determined by the bandgap of the quantum well layers will be absorbed and will produce an electrical potential across said junction.

  6. Quantum well multijunction photovoltaic cell

    DOE Patents [OSTI]

    Chaffin, R.J.; Osbourn, G.C.

    1983-07-08

    A monolithic, quantum well, multilayer photovoltaic cell comprises a p-n junction comprising a p-region on one side and an n-region on the other side, each of which regions comprises a series of at least three semiconductor layers, all p-type in the p-region and all n-type in the n-region; each of said series of layers comprising alternating barrier and quantum well layers, each barrier layer comprising a semiconductor material having a first bandgap and each quantum well layer comprising a semiconductor material having a second bandgap when in bulk thickness which is narrower than said first bandgap, the barrier layers sandwiching each quantum well layer and each quantum well layer being sufficiently thin that the width of its bandgap is between said first and second bandgaps, such that radiation incident on said cell and above an energy determined by the bandgap of the quantum well layers will be absorbed and will produce an electrical potential across said junction.

  7. Well-Tech Award 2008 Well-Tech Award 2007

    E-Print Network [OSTI]

    Chiao, Jung-Chih

    ://www.well-tech.it/_nuovo%20sito_/anteprima%202009/anteprima_2009_acce.html #12;ACCESSIBILITY Protesi di nuova generazione che farlo diventare il più naturale possibile, cercando un perfetto equilibrio tra protesi e corpo. Able - B Protesi di nuova generazione che punta ad ottimizzare comfort, propriocezione, andatura, postura, estetica

  8. Subsurface steam sampling in Geysers wells

    SciTech Connect (OSTI)

    Lysne, P. [Lysne (Peter), Albuquerque, NM (United States); Koenig, B. [Unocal Geothermal and Power Operations Group, Santa Rose, CA (United States); Hirtz, P. [Thermochem, Inc., Santa Rosa, CA (United States); Normann, R.; Henfling, J. [Sandia National Labs., Albuquerque, NM (United States)

    1997-01-01

    A new downhole sampling tool has been built for use in steam wells at The Geysers geothermal reservoir. The tool condenses specimens into an initially evacuated vessel that is opened down hole at the direction of an on-board computer. The tool makes a temperature log of the well as it is deployed, and the pressure and temperature of collected specimens are monitored for diagnostic purposes. Initial tests were encouraging, and the Department of Energy has funded an expanded effort that includes data gathering needed to develop a three-dimensional model of The Geysers geochemical environment. Collected data will be useful for understanding the origins of hydrogen chloride and non-condensable gases in the steam, as well as tracking the effect of injection on the composition of produced steam. Interested parties are invited to observe the work and to join the program.

  9. Well completion and servicing fluid

    SciTech Connect (OSTI)

    Grimsley, R.L.

    1990-09-25

    This patent describes a well completion servicing fluid for controlling formation pressure during completion or servicing of a well. It comprises: an aqueous solution of calcium chloride, a solid weighing agent suspended in the solution and being selected from the group consisting of zinc, zinc oxide, and mixtures thereof; and a viscosifier dissolved in the solution in an amount effective to suspend the weighing agent. The fluid has a density of greater than 15 pounds per gallon and being substantially free of bromide ions and being substantially free of solid material which is not soluble in hydrochloric acid.

  10. Risk-Informed Safety Margin Characterization Methods Development Work

    SciTech Connect (OSTI)

    Smith, Curtis L; Ma, Zhegang; Tom Riley; Mandelli, Diego; Nielsen, Joseph W; Alfonsi, Andrea; Rabiti, Cristian

    2014-09-01

    This report summarizes the research activity developed during the Fiscal year 2014 within the Risk Informed Safety Margin and Characterization (RISMC) pathway within the Light Water Reactor Sustainability (LWRS) campaign. This research activity is complementary to the one presented in the INL/EXT-??? report which shows advances Probabilistic Risk Assessment Analysis using RAVEN and RELAP-7 in conjunction to novel flooding simulation tools. Here we present several analyses that prove the values of the RISMC approach in order to assess risk associated to nuclear power plants (NPPs). We focus on simulation based PRA which, in contrast to classical PRA, heavily employs system simulator codes. Firstly we compare, these two types of analyses, classical and RISMC, for a Boiling water reactor (BWR) station black out (SBO) initiating event. Secondly we present an extended BWR SBO analysis using RAVEN and RELAP-5 which address the comments and suggestions received about he original analysis presented in INL/EXT-???. This time we focus more on the stochastic analysis such probability of core damage and on the determination of the most risk-relevant factors. We also show some preliminary results regarding the comparison between RELAP5-3D and the new code RELAP-7 for a simplified Pressurized Water Reactors system. Lastly we present some conceptual ideas regarding the possibility to extended the RISMC capabilities from an off-line tool (i.e., as PRA analysis tool) to an online-tool. In this new configuration, RISMC capabilities can be used to assist and inform reactor operator during real accident scenarios.

  11. Bounding the marginal cost of producing potable water including the use of seawater desalinization as a backstop potable water production technology

    SciTech Connect (OSTI)

    Dooley, James J.

    2014-04-01

    The analysis presented in this technical report should allow for the creation of high, medium, and low cost potable water prices for GCAM. Seawater reverse osmosis (SWRO) based desalinization should act as a backstop for the cost of producing potable water (i.e., the literature seems clear that SWRO should establish an upper bound for the plant gate cost of producing potable water). Transporting water over significant distances and having to lift water to higher elevations to reach end-users can also have a significant impact on the cost of producing water. The three potable fresh water scenarios describe in this technical report are: low cost water scenario ($0.10/m3); medium water cost scenario ($1.00/m3); and high water cost scenario ($2.50/m3).

  12. Process for cementing geothermal wells

    DOE Patents [OSTI]

    Eilers, Louis H. (Inola, OK)

    1985-01-01

    A pumpable slurry of coal-filled furfuryl alcohol, furfural, and/or a low molecular weight mono- or copolymer thereof containing, preferably, a catalytic amount of a soluble acid catalyst is used to cement a casing in a geothermal well.

  13. Entiat 4Mile WELLs Completion Report, 2006.

    SciTech Connect (OSTI)

    Malinowksi, Richard

    2007-01-01

    The Entiat 4-mile Wells (Entiat 4-mile) project is located in the Entiat subbasin and will benefit Upper Columbia steelhead, spring Chinook and bull trout. The goal of this project is to prevent juvenile fish from being diverted into an out-of-stream irrigation system and to eliminate impacts due to the annual maintenance of an instream pushup dam. The objectives include eliminating a surface irrigation diversion and replacing it with two wells, which will provide Bonneville Power Administration (BPA) and the Bureau of Reclamation (Reclamation) with a Federal Columbia River Power System (FCRPS) BiOp metric credit of one. Wells were chosen over a new fish screen based on biological benefits and costs. Long-term biological benefits are provided by completely eliminating the surface diversion and the potential for fish entrainment in a fish screen. Construction costs for a new fish screen were estimated at $150,000, which does not include other costs associated with implementing and maintaining a fish screening project. Construction costs for a well were estimated at $20,000 each. The diversion consisted of a pushup dam that diverted water into an off-channel pond. Water was then pumped into a pressurized system for irrigation. There are 3 different irrigators who used water from this surface diversion, and each has multiple water right claims totaling approximately 5 cfs. Current use was estimated at 300 gallons per minute (approximately 0.641 cfs). Some irrigated acreage was taken out of orchard production less than 5 years ago. Therefore, approximately 6.8 acre-feet will be put into the State of Washington Trust Water Right program. No water will be set aside for conservation savings. The construction of the two irrigation wells for three landowners was completed in September 2006. The Lower Well (Tippen/Wick) will produce up to 175 gpm while the Upper Well (Griffith) will produce up to 275 gpm during the irrigation season. The eight inch diameter wells were developed to a depth of 75 feet and 85 feet, respectively, and will be pumped with Submersible Turbine pumps. The irrigation wells have been fitted with new electric boxes and Siemens flowmeters (MAG8000).

  14. Benthic biological and biogeochemical patterns and processes across an oxygen minimum zone (Pakistan margin, NE Arabian Sea)

    E-Print Network [OSTI]

    Levin, Lisa

    (Pakistan margin, NE Arabian Sea) Gregory L. Cowie a,Ã, Lisa A. Levin b a The Sir John Murray Laboratories), and organic matter (OM) availability on benthic communities and processes across the Pakistan Margin

  15. Supplementary Materials Table 1: Simulated log-normal survival data marginal posterior probability of inclusion of relevant

    E-Print Network [OSTI]

    Vannucci, Marina

    .1835 Table 1: Simulated log-normal survival data: Marginal posterior probabilities of inclusion of rele- vant: Marginal posterior probabilities of inclusion of rele- vant variables under different maximum correlation

  16. Solitons and vortices in nonlinear potential wells

    E-Print Network [OSTI]

    Dror, Nir

    2015-01-01

    We consider self-trapping of topological modes governed by the one- and two-dimensional (1D and 2D) nonlinear-Schrodinger/Gross-Pitaevskii equation with effective single- and double-well (DW) nonlinear potentials induced by spatial modulation of the local strength of the self-defocusing nonlinearity. This setting, which may be implemented in optics and Bose-Einstein condensates, aims to extend previous studies, which dealt with single-well nonlinear potentials. In the 1D setting, we find several types of symmetric, asymmetric and antisymmetric states, focusing on scenarios of the spontaneous symmetry breaking. The single-well model is extended by including rocking motion of the well, which gives rise to Rabi oscillations between the fundamental and dipole modes. Analysis of the 2D single-well setting gives rise to stable modes in the form of ordinary dipoles, vortex-antivortex dipoles (VADs), and vortex triangles (VTs), which may be considered as produced by spontaneous breaking of the axial symmetry. The con...

  17. Health Education & Wellness - HPMC Occupational Health Services

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Wellness Health Education & Wellness Health Education & Wellness Downloads & Patient Materials Health & Productivity Health Calculators & Logs Health Coaching Health Fairs and...

  18. Oxygen and organic matter thresholds for benthic faunal activity on the Pakistan margin oxygen minimum zone (7001100 m)

    E-Print Network [OSTI]

    Levin, Lisa

    Oxygen and organic matter thresholds for benthic faunal activity on the Pakistan margin oxygen) on the bathyal Pakistan margin, where sediments grade from fully laminated sediment at 700 m (0.12 mL LÀ1 O2 [5 m matter to generate abrupt faunal transitions on the Pakistan margin. & 2008 Elsevier Ltd. All rights

  19. Stochastic modeling and survival analysis of marginally trapped neutrons for a magnetic trapping neutron lifetime experiment

    E-Print Network [OSTI]

    K. J. Coakley; M. S. Dewey; M. G. Huber; P. R. Huffman; C. R. Huffer; D. E. Marley; H. P. Mumm; C. M. O'Shaughnessy; K. W. Schelhammer; A. K. Thompson; A. T. Yue

    2015-08-10

    In a variety of neutron lifetime experiments, in addition to $\\beta-$decay, neutrons can be lost by other mechanisms including wall losses. Failure to account for these other loss mechanisms produces systematic measurement error and associated systematic uncertainties in neutron lifetime measurements. In this work, we develop a physical model for neutron wall losses and construct a competing risks survival analysis model to account for losses due to the joint effect of $\\beta-$decay losses, wall losses of marginally trapped neutrons, and an additional absorption mechanism. We determine the survival probability function associated with the wall loss mechanism by a Monte Carlo method. Based on a fit of the competing risks model to a subset of the NIST experimental data, we determine the mean lifetime of trapped neutrons to be approximately 700 s -- considerably less than the current best estimate of (880.1 $\\pm$ 1.1) s promulgated by the Particle Data Group [1]. Currently, experimental studies are underway to determine if this discrepancy can be explained by neutron capture by ${}^3$He impurities in the trapping volume. Analysis of the full NIST data will be presented in a later publication.

  20. Scattered light images of spiral arms in marginally gravitationally unstable discs with an embedded planet

    E-Print Network [OSTI]

    Pohl, A; Benisty, M; Ataiee, S; Juhasz, A; Dullemond, C P; Van Boekel, R; Henning, T

    2015-01-01

    Scattered light images of transition discs in the near-infrared often show non-axisymmetric structures in the form of wide-open spiral arms in addition to their characteristic low-opacity inner gap region. We study self-gravitating discs and investigate the influence of gravitational instability on the shape and contrast of spiral arms induced by planet-disc interactions. Two-dimensional non-isothermal hydrodynamical simulations including viscous heating and a cooling prescription are combined with three-dimensional dust continuum radiative transfer models for direct comparison to observations. We find that the resulting contrast between the spirals and the surrounding disc in scattered light is by far higher for pressure scale height variations, i.e. thermal perturbations, than for pure surface density variations. Self-gravity effects suppress any vortex modes and tend to reduce the opening angle of planet-induced spirals, making them more tightly wound. If the disc is only marginally gravitationally stable ...

  1. Margin of Safety Definition and Examples Used in Safety Basis Documents and the USQ Process

    SciTech Connect (OSTI)

    Beaulieu, R. A.

    2013-10-03

    The Nuclear Safety Management final rule, 10 CFR 830, provides an undefined term, margin of safety (MOS). Safe harbors listed in 10 CFR 830, Table 2, such as DOE?STD?3009 use but do not define the term. This lack of definition has created the need for the definition. This paper provides a definition of MOS and documents examples of MOS as applied in a U.S. Department of Energy (DOE) approved safety basis for an existing nuclear facility. If we understand what MOS looks like regarding Technical Safety Requirements (TSR) parameters, then it helps us compare against other parameters that do not involve a MOS. This paper also documents parameters that are not MOS. These criteria could be used to determine if an MOS exists in safety basis documents. This paper helps DOE, including the National Nuclear Security Administration (NNSA) and its contractors responsible for the safety basis improve safety basis documents and the unreviewed safety question (USQ) process with respect to MOS.

  2. A new well surveying tool 

    E-Print Network [OSTI]

    Haghighi, Manuchehr Mehdizabeh

    1966-01-01

    13 13 11 12 15 l2 48 51 51 51 49 49 49 51 50 49 Undetermined values. 'ARABLE II COMPARISON OF MEASURED ANGLES @ID ANGLES INDICATE' EY SURVEYING DEVICE ACTUAL VALUES EERIE(;QVENTAL VALUES Rnn No. 1 Run No. 2 Depth: Direction of...A NEW WELL SURVEYING TOOL A Thesis By MANUCHEHR MEHDIZABEH HAGHIGHI Submitted to the Graduate College of the Texas ANM University in partial fulfillment of the requirements for the degree of MASTER OF SCIENCE Major Subject: PETROLEUM...

  3. Well Deepening | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmental Jump to:EA EISTJThinWarsaw, Poland:EnergyWe Energy Wind FarmWege WindWeldWell

  4. Wellness Services | The Ames Laboratory

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantityBonneville Power AdministrationRobust,Field-effectWorking WithTelecentricN AProjectAdministration NNSAWellWellness Services

  5. INSTRUMENTATION, INCLUDING NUCLEAR AND PARTICLE DETECTORS; RADIATION

    Office of Scientific and Technical Information (OSTI)

    interval technical basis document Chiaro, P.J. Jr. 44 INSTRUMENTATION, INCLUDING NUCLEAR AND PARTICLE DETECTORS; RADIATION DETECTORS; RADIATION MONITORS; DOSEMETERS;...

  6. Understanding the Zongo : processes of socio-spatial marginalization in Ghana

    E-Print Network [OSTI]

    Williamson, Emily Anne

    2014-01-01

    The spatial processes of marginalization and ghettoization have been described, labeled, and theorized extensively in the United States and Europe, yet there has been little research dedicated to these processes in the ...

  7. Analysis of post-Kyoto CO? emissions trading using marginal abatement curves

    E-Print Network [OSTI]

    Ellerman, A. Denny.; Decaux, Annelène.

    Marginal abatement curves (MACs) are often used heuristically to demonstrate the advantages of emissions trading. In this paper, the authors derive MACs from EPPA, the MIT Joint Program's computable general equilibrium ...

  8. Storytelling on the margins : a theoretical framework for imagining a fashion innovation center in Tuscany

    E-Print Network [OSTI]

    Mills, Alexa (Alexa Timeaus)

    2008-01-01

    The importance of the margin has long been deemed important in creative processes. At both the level of the individual and the level of the city, research shows that creativity tends to flourish on the philosophical and ...

  9. Some Improvements to the Shenoy-Shafer and Hugin Architectures for Computing Marginals

    E-Print Network [OSTI]

    Schmidt, Tuija; Shenoy, Prakash P.

    1998-01-01

    The main aim of this paper is to describe two modifications to the Shenoy–Shafer architecture with the goal of making it computationally more efficient in computing marginals of the joint valuation. We also describe a ...

  10. The evolution of lithospheric deformation and crustal structure from continental margins to oceanic spreading centers

    E-Print Network [OSTI]

    Behn, Mark Dietrich, 1974-

    2002-01-01

    This thesis investigates the evolution of lithospheric deformation and crustal structure from continental margins to mid-ocean ridges. The first part (Ch. 2) examines the style of segmentation along the U.S. East Coast ...

  11. A reference time scale for Site U1385 (Shackleton Site) on the SW Iberian Margin

    E-Print Network [OSTI]

    Hodell, D.; Lourens, L.; Crowhurst, S.; Konijnendijk, T.; Tjallingii, R.; Jimenez-Espejo, F.; Skinner, L.; Tzedakis, P. C.

    2015-07-16

    ACCEPTED MANUSCRIPT 5 fidelity of the sediments on the SW Iberian Margin make this region a prime target for ocean drilling. In 2011, an Ancillary Program Letter (APL 763) was submitted to the Integrated Ocean Drilling Program (IODP) requesting four...

  12. Estimating Marginal Returns to Medical Care: Evidence from At-Risk Newborns

    E-Print Network [OSTI]

    Almond, Douglas

    A key policy question is whether the benefits of additional medical expenditures exceed their costs. We propose a new approach for estimating marginal returns to medical spending based on variation in medical inputs generated ...

  13. National Geo-Database for Biofuel Simulations and Regional Analysis of Biorefinery Siting Based on Cellulosic Feedstock Grown on Marginal Lands

    SciTech Connect (OSTI)

    Izaurralde, Roberto C.; Zhang, Xuesong; Sahajpal, Ritvik; Manowitz, David H.

    2012-04-01

    The goal of this project undertaken by GLBRC (Great Lakes Bioenergy Research Center) Area 4 (Sustainability) modelers is to develop a national capability to model feedstock supply, ethanol production, and biogeochemical impacts of cellulosic biofuels. The results of this project contribute to sustainability goals of the GLBRC; i.e. to contribute to developing a sustainable bioenergy economy: one that is profitable to farmers and refiners, acceptable to society, and environmentally sound. A sustainable bioenergy economy will also contribute, in a fundamental way, to meeting national objectives on energy security and climate mitigation. The specific objectives of this study are to: (1) develop a spatially explicit national geodatabase for conducting biofuel simulation studies and (4) locate possible sites for the establishment of cellulosic ethanol biorefineries. To address the first objective, we developed SENGBEM (Spatially Explicit National Geodatabase for Biofuel and Environmental Modeling), a 60-m resolution geodatabase of the conterminous USA containing data on: (1) climate, (2) soils, (3) topography, (4) hydrography, (5) land cover/ land use (LCLU), and (6) ancillary data (e.g., road networks, federal and state lands, national and state parks, etc.). A unique feature of SENGBEM is its 2008-2010 crop rotation data, a crucially important component for simulating productivity and biogeochemical cycles as well as land-use changes associated with biofuel cropping. ARRA support for this project and to the PNNL Joint Global Change Research Institute enabled us to create an advanced computing infrastructure to execute millions of simulations, conduct post-processing calculations, store input and output data, and visualize results. These computing resources included two components installed at the Research Data Center of the University of Maryland. The first resource was 'deltac': an 8-core Linux server, dedicated to county-level and state-level simulations and PostgreSQL database hosting. The second resource was the DOE-JGCRI 'Evergreen' cluster, capable of executing millions of simulations in relatively short periods. ARRA funding also supported a PhD student from UMD who worked on creating the geodatabases and executing some of the simulations in this study. Using a physically based classification of marginal lands, we simulated production of cellulosic feedstocks from perennial mixtures grown on these lands in the US Midwest. Marginal lands in the western states of the US Midwest appear to have significant potential to supply feedstocks to a cellulosic biofuel industry. Similar results were obtained with simulations of N-fertilized perennial mixtures. A detailed spatial analysis allowed for the identification of possible locations for the establishment of 34 cellulosic ethanol biorefineries with an annual production capacity of 5.6 billion gallons. In summary, we have reported on the development of a spatially explicit national geodatabase to conduct biofuel simulation studies and provided simulation results on the potential of perennial cropping systems to serve as feedstocks for the production of cellulosic ethanol. To accomplish this, we have employed sophisticated spatial analysis methods in combination with the process-based biogeochemical model EPIC. The results of this study will be submitted to the USDOE Bioenergy Knowledge Discovery Framework as a way to contribute to the development of a sustainable bioenergy industry. This work provided the opportunity to test the hypothesis that marginal lands can serve as sources of cellulosic feedstocks and thus contribute to avoid potential conflicts between bioenergy and food production systems. This work, we believe, opens the door for further analysis on the characteristics of cellulosic feedstocks as major contributors to the development of a sustainable bioenergy economy.

  14. TEX-A-SYST: Reducing the Risk of Ground Water Contamination by Improving Well-Head Management and Conditions 

    E-Print Network [OSTI]

    Harris, Bill L.; Hoffman, D.; Mazac Jr., F. J.

    1997-08-29

    The condition of a water well and its proximity to contamination sources determine the risk it poses to ground water. Topics covered include well location, well construction, well age and type, well depth, well maintenance, water testing...

  15. Risk Informed Safety Margin Characterization Case Study: Selection of Electrical Equipment To Be Subjected to Environmental Qualification

    SciTech Connect (OSTI)

    D. Blanchard; R. Youngblood

    2012-04-01

    In general, the margins-based safety case helps the decision-maker manage plant margins most effectively. It tells the plant decision-maker such things as what margin is present (at the plant level, at the functional level, at the barrier level, at the component level), and where margin is thin or perhaps just degrading. If the plant is safe, it tells the decision-maker why the plant is safe and where margin needs to be maintained, and perhaps where the plant can afford to relax.

  16. Risk Informed Safety Margin Characterization Case Study: Selection of Electrical Equipment To Be Subjected to Environmental Qualification

    SciTech Connect (OSTI)

    R. Youngblood; D. Blanchard

    2011-09-01

    In general, the margins-based safety case helps the decision-maker manage plant margins most effectively. It tells the plant decision-maker such things as what margin is present (at the plant level, at the functional level, at the barrier level, at the component level), and where margin is thin or perhaps just degrading. If the plant is safe, it tells the decision-maker why the plant is safe and where margin needs to be maintained, and perhaps where the plant can afford to relax.

  17. Multi-well sample plate cover penetration system

    DOE Patents [OSTI]

    Beer, Neil Reginald (Pleasanton, CA)

    2011-12-27

    An apparatus for penetrating a cover over a multi-well sample plate containing at least one individual sample well includes a cutting head, a cutter extending from the cutting head, and a robot. The cutting head is connected to the robot wherein the robot moves the cutting head and cutter so that the cutter penetrates the cover over the multi-well sample plate providing access to the individual sample well. When the cutting head is moved downward the foil is pierced by the cutter that splits, opens, and folds the foil inward toward the well. The well is then open for sample aspiration but has been protected from cross contamination.

  18. Electricity prices in a competitive environment: Marginal cost pricing of generation services and financial status of electric utilities. A preliminary analysis through 2015

    SciTech Connect (OSTI)

    1997-08-01

    The emergence of competitive markets for electricity generation services is changing the way that electricity is and will be priced in the United States. This report presents the results of an analysis that focuses on two questions: (1) How are prices for competitive generation services likely to differ from regulated prices if competitive prices are based on marginal costs rather than regulated {open_quotes}cost-of-service{close_quotes} pricing? (2) What impacts will the competitive pricing of generation services (based on marginal costs) have on electricity consumption patterns, production costs, and the financial integrity patterns, production costs, and the financial integrity of electricity suppliers? This study is not intended to be a cost-benefit analysis of wholesale or retail competition, nor does this report include an analysis of the macroeconomic impacts of competitive electricity prices.

  19. Course may include: Research in Education

    E-Print Network [OSTI]

    Course may include: Research in Education Statistics in Education Theories of Educational Admin Policy Analysis Sociological Aspects of Education Approaches to Literacy Development Information and Communication Technologies Issues in Education Final Project Seminar Master of Education Educational

  20. Gas storage materials, including hydrogen storage materials

    DOE Patents [OSTI]

    Mohtadi, Rana F; Wicks, George G; Heung, Leung K; Nakamura, Kenji

    2014-11-25

    A material for the storage and release of gases comprises a plurality of hollow elements, each hollow element comprising a porous wall enclosing an interior cavity, the interior cavity including structures of a solid-state storage material. In particular examples, the storage material is a hydrogen storage material, such as a solid state hydride. An improved method for forming such materials includes the solution diffusion of a storage material solution through a porous wall of a hollow element into an interior cavity.

  1. Gas storage materials, including hydrogen storage materials

    DOE Patents [OSTI]

    Mohtadi, Rana F; Wicks, George G; Heung, Leung K; Nakamura, Kenji

    2013-02-19

    A material for the storage and release of gases comprises a plurality of hollow elements, each hollow element comprising a porous wall enclosing an interior cavity, the interior cavity including structures of a solid-state storage material. In particular examples, the storage material is a hydrogen storage material such as a solid state hydride. An improved method for forming such materials includes the solution diffusion of a storage material solution through a porous wall of a hollow element into an interior cavity.

  2. INDEX TO VOLUME 146 (PART 1) Cascadia Margin

    E-Print Network [OSTI]

    , geologic, and other terms are referenced only if they are subjects of discussion. This index also includes, defined as a keyword or concept followed by a reference to the page on which that word or concept appears, and (2) a subentry, defined as an elaboration on the main entry fol- lowed by a page reference. The index

  3. Remote down-hole well telemetry

    DOE Patents [OSTI]

    Briles, Scott D. (Los Alamos, NM); Neagley, Daniel L. (Albuquerque, NM); Coates, Don M. (Santa Fe, NM); Freund, Samuel M. (Los Alamos, NM)

    2004-07-20

    The present invention includes an apparatus and method for telemetry communication with oil-well monitoring and recording instruments located in the vicinity of the bottom of gas or oil recovery pipes. Such instruments are currently monitored using electrical cabling that is inserted into the pipes; cabling has a short life in this environment, and requires periodic replacement with the concomitant, costly shutdown of the well. Modulated reflectance, a wireless communication method that does not require signal transmission power from the telemetry package will provide a long-lived and reliable way to monitor down-hole conditions. Normal wireless technology is not practical since batteries and capacitors have to frequently be replaced or recharged, again with the well being removed from service. RF energy generated above ground can also be received, converted and stored down-hole without the use of wires, for actuating down-hole valves, as one example. Although modulated reflectance reduces or eliminates the loss of energy at the sensor package because energy is not consumed, during the transmission process, additional stored extra energy down-hole is needed.

  4. INVITATIONAL WELL-TESTING SYMPOSIUM PROCEEDINGS

    E-Print Network [OSTI]

    Authors, Various

    2011-01-01

    to obser- vation well, L; vertical hydraulic conductivity ofGas Wells Stimulated by Massive Hydraulic Fracturing," SPEproduc- tion well, L; hori zontal hydraulic conductivi ty,

  5. Scramjet including integrated inlet and combustor

    SciTech Connect (OSTI)

    Kutschenreuter, P.H. Jr.; Blanton, J.C.

    1992-02-04

    This patent describes a scramjet engine. It comprises: a first surface including an aft facing step; a cowl including: a leading edge and a trailing edge; an upper surface and a lower surface extending between the leading edge and the trailing edge; the cowl upper surface being spaced from and generally parallel to the first surface to define an integrated inlet-combustor therebetween having an inlet for receiving and channeling into the inlet-combustor supersonic inlet airflow; means for injecting fuel into the inlet-combustor at the step for mixing with the supersonic inlet airflow for generating supersonic combustion gases; and further including a spaced pari of sidewalls extending between the first surface to the cowl upper surface and wherein the integrated inlet-combustor is generally rectangular and defined by the sidewall pair, the first surface and the cowl upper surface.

  6. Electric Power Monthly, August 1990. [Glossary included

    SciTech Connect (OSTI)

    Not Available

    1990-11-29

    The Electric Power Monthly (EPM) presents monthly summaries of electric utility statistics at the national, Census division, and State level. The purpose of this publication is to provide energy decisionmakers with accurate and timely information that may be used in forming various perspectives on electric issues that lie ahead. Data includes generation by energy source (coal, oil, gas, hydroelectric, and nuclear); generation by region; consumption of fossil fuels for power generation; sales of electric power, cost data; and unusual occurrences. A glossary is included.

  7. MOTIVATION INCLUDED OR EXCLUDED FROM Mihaela Cocea

    E-Print Network [OSTI]

    Cocea, Mihaela

    MOTIVATION ­ INCLUDED OR EXCLUDED FROM E-LEARNING Mihaela Cocea National College of Ireland Mayor, Dublin 1, Ireland sweibelzahl@ncirl.ie ABSTRACT The learners' motivation has an impact on the quality-Learning, motivation has been mainly considered in terms of instructional design. Research in this direction suggests

  8. Energy Consumption of Personal Computing Including Portable

    E-Print Network [OSTI]

    Namboodiri, Vinod

    processing unit (CPU) processing power and capacity of mass storage devices doubles every 18 months. Such growth in both processing and storage capabilities fuels the production of ever more powerful portableEnergy Consumption of Personal Computing Including Portable Communication Devices Pavel Somavat1

  9. Course may include: Research in Education

    E-Print Network [OSTI]

    Development Information and Communication Technologies Issues in Education Final Project Seminar Master, the Final Project Seminar. This graduate program will allow you to develop your skills and knowledgeCourse may include: Research in Education Qualitative Methods in Educational Research Fundamentals

  10. Communication in automation, including networking and wireless

    E-Print Network [OSTI]

    Antsaklis, Panos

    Communication in automation, including networking and wireless Nicholas Kottenstette and Panos J and networking in automation is given. Digital communication fundamentals are reviewed and networked control are presented. 1 Introduction 1.1 Why communication is necessary in automated systems Automated systems use

  11. Quantification of margins and uncertainty for risk-informed decision analysis.

    SciTech Connect (OSTI)

    Alvin, Kenneth Fredrick

    2010-09-01

    QMU stands for 'Quantification of Margins and Uncertainties'. QMU is a basic framework for consistency in integrating simulation, data, and/or subject matter expertise to provide input into a risk-informed decision-making process. QMU is being applied to a wide range of NNSA stockpile issues, from performance to safety. The implementation of QMU varies with lab and application focus. The Advanced Simulation and Computing (ASC) Program develops validated computational simulation tools to be applied in the context of QMU. QMU provides input into a risk-informed decision making process. The completeness aspect of QMU can benefit from the structured methodology and discipline of quantitative risk assessment (QRA)/probabilistic risk assessment (PRA). In characterizing uncertainties it is important to pay attention to the distinction between those arising from incomplete knowledge ('epistemic' or systematic), and those arising from device-to-device variation ('aleatory' or random). The national security labs should investigate the utility of a probability of frequency (PoF) approach in presenting uncertainties in the stockpile. A QMU methodology is connected if the interactions between failure modes are included. The design labs should continue to focus attention on quantifying uncertainties that arise from epistemic uncertainties such as poorly-modeled phenomena, numerical errors, coding errors, and systematic uncertainties in experiment. The NNSA and design labs should ensure that the certification plan for any RRW is supported by strong, timely peer review and by an ongoing, transparent QMU-based documentation and analysis in order to permit a confidence level necessary for eventual certification.

  12. Health and Wellness Guide for Students Introduction

    E-Print Network [OSTI]

    Health and Wellness Guide for Students #12;Introduction What is Wellness? Wellness is an active life. Many factors can influence your health and well-being, in fact there are 7 different, interacting dimensions of health and wellness. The 7 dimensions are: Physical Wellness ­ Taking care of your body

  13. Subterranean barriers including at least one weld

    DOE Patents [OSTI]

    Nickelson, Reva A.; Sloan, Paul A.; Richardson, John G.; Walsh, Stephanie; Kostelnik, Kevin M.

    2007-01-09

    A subterranean barrier and method for forming same are disclosed, the barrier including a plurality of casing strings wherein at least one casing string of the plurality of casing strings may be affixed to at least another adjacent casing string of the plurality of casing strings through at least one weld, at least one adhesive joint, or both. A method and system for nondestructively inspecting a subterranean barrier is disclosed. For instance, a radiographic signal may be emitted from within a casing string toward an adjacent casing string and the radiographic signal may be detected from within the adjacent casing string. A method of repairing a barrier including removing at least a portion of a casing string and welding a repair element within the casing string is disclosed. A method of selectively heating at least one casing string forming at least a portion of a subterranean barrier is disclosed.

  14. Photoactive devices including porphyrinoids with coordinating additives

    DOE Patents [OSTI]

    Forrest, Stephen R; Zimmerman, Jeramy; Yu, Eric K; Thompson, Mark E; Trinh, Cong; Whited, Matthew; Diev, Vlacheslav

    2015-05-12

    Coordinating additives are included in porphyrinoid-based materials to promote intermolecular organization and improve one or more photoelectric characteristics of the materials. The coordinating additives are selected from fullerene compounds and organic compounds having free electron pairs. Combinations of different coordinating additives can be used to tailor the characteristic properties of such porphyrinoid-based materials, including porphyrin oligomers. Bidentate ligands are one type of coordinating additive that can form coordination bonds with a central metal ion of two different porphyrinoid compounds to promote porphyrinoid alignment and/or pi-stacking. The coordinating additives can shift the absorption spectrum of a photoactive material toward higher wavelengths, increase the external quantum efficiency of the material, or both.

  15. Power generation method including membrane separation

    DOE Patents [OSTI]

    Lokhandwala, Kaaeid A. (Union City, CA)

    2000-01-01

    A method for generating electric power, such as at, or close to, natural gas fields. The method includes conditioning natural gas containing C.sub.3+ hydrocarbons and/or acid gas by means of a membrane separation step. This step creates a leaner, sweeter, drier gas, which is then used as combustion fuel to run a turbine, which is in turn used for power generation.

  16. Rotor assembly including superconducting magnetic coil

    DOE Patents [OSTI]

    Snitchler, Gregory L. (Shrewsbury, MA); Gamble, Bruce B. (Wellesley, MA); Voccio, John P. (Somerville, MA)

    2003-01-01

    Superconducting coils and methods of manufacture include a superconductor tape wound concentrically about and disposed along an axis of the coil to define an opening having a dimension which gradually decreases, in the direction along the axis, from a first end to a second end of the coil. Each turn of the superconductor tape has a broad surface maintained substantially parallel to the axis of the coil.

  17. Nuclear reactor shield including magnesium oxide

    DOE Patents [OSTI]

    Rouse, Carl A. (Del Mar, CA); Simnad, Massoud T. (La Jolla, CA)

    1981-01-01

    An improvement in nuclear reactor shielding of a type used in reactor applications involving significant amounts of fast neutron flux, the reactor shielding including means providing structural support, neutron moderator material, neutron absorber material and other components as described below, wherein at least a portion of the neutron moderator material is magnesium in the form of magnesium oxide either alone or in combination with other moderator materials such as graphite and iron.

  18. Electric power monthly, September 1990. [Glossary included

    SciTech Connect (OSTI)

    Not Available

    1990-12-17

    The purpose of this report is to provide energy decision makers with accurate and timely information that may be used in forming various perspectives on electric issues. The power plants considered include coal, petroleum, natural gas, hydroelectric, and nuclear power plants. Data are presented for power generation, fuel consumption, fuel receipts and cost, sales of electricity, and unusual occurrences at power plants. Data are compared at the national, Census division, and state levels. 4 figs., 52 tabs. (CK)

  19. Pumpernickel Valley Geothermal Project Thermal Gradient Wells

    SciTech Connect (OSTI)

    Z. Adam Szybinski

    2006-01-01

    The Pumpernickel Valley geothermal project area is located near the eastern edge of the Sonoma Range and is positioned within the structurally complex Winnemucca fold and thrust belt of north-central Nevada. A series of approximately north-northeast-striking faults related to the Basin and Range tectonics are superimposed on the earlier structures within the project area, and are responsible for the final overall geometry and distribution of the pre-existing structural features on the property. Two of these faults, the Pumpernickel Valley fault and Edna Mountain fault, are range-bounding and display numerous characteristics typical of strike-slip fault systems. These characteristics, when combined with geophysical data from Shore (2005), indicate the presence of a pull-apart basin, formed within the releasing bend of the Pumpernickel Valley – Edna Mountain fault system. A substantial body of evidence exists, in the form of available geothermal, geological and geophysical information, to suggest that the property and the pull-apart basin host a structurally controlled, extensive geothermal field. The most evident manifestations of the geothermal activity in the valley are two areas with hot springs, seepages, and wet ground/vegetation anomalies near the Pumpernickel Valley fault, which indicate that the fault focuses the fluid up-flow. There has not been any geothermal production from the Pumpernickel Valley area, but it was the focus of a limited exploration effort by Magma Power Company. In 1974, the company drilled one exploration/temperature gradient borehole east of the Pumpernickel Valley fault and recorded a thermal gradient of 160oC/km. The 1982 temperature data from five unrelated mineral exploration holes to the north of the Magma well indicated geothermal gradients in a range from 66 to 249oC/km for wells west of the fault, and ~283oC/km in a well next to the fault. In 2005, Nevada Geothermal Power Company drilled four geothermal gradient wells, PVTG-1, -2, -3, and -4, and all four encountered geothermal fluids. The holes provided valuable water geochemistry, supporting the geothermometry results obtained from the hot springs and Magma well. The temperature data gathered from all the wells clearly indicates the presence of a major plume of thermal water centered on the Pumpernickel Valley fault, and suggests that the main plume is controlled, at least in part, by flow from this fault system. The temperature data also defines the geothermal resource with gradients >100oC/km, which covers an area a minimum of 8 km2. Structural blocks, down dropped with respect to the Pumpernickel Valley fault, may define an immediate reservoir. The geothermal system almost certainly continues beyond the recently drilled holes and might be open to the east and south, whereas the heat source responsible for the temperatures associated with this plume has not been intersected and must be at a depth greater than 920 meters (depth of the deepest well – Magma well). The geological and structural setting and other characteristics of the Pumpernickel Valley geothermal project area are markedly similar to the portions of the nearby Dixie Valley geothermal field. These similarities include, among others, the numerous, unexposed en echelon faults and large-scale pull-apart structure, which in Dixie Valley may host part of the geothermal field. The Pumpernickel Valley project area, for the majority of which Nevada Geothermal Power Company has geothermal rights, represents a geothermal site with a potential for the discovery of a relatively high temperature reservoir suitable for electric power production. Among locations not previously identified as having high geothermal potential, Pumpernickel Valley has been ranked as one of four sites with the highest potential for electrical power production in Nevada (Shevenell and Garside, 2003). Richards and Blackwell (2002) estimated the total heat loss and the preliminary production capacity for the entire Pumpernickel Valley geothermal system to be at 35MW. A more conservative estimate, for

  20. Quantification of the Variability of Diaphragm Motion and Implications for Treatment Margin Construction

    SciTech Connect (OSTI)

    Rit, Simon; Herk, Marcel van; Zijp, Lambert [Department of Radiation Oncology, The Netherlands Cancer Institute-Antoni van Leeuwenhoek Hospital, Amsterdam (Netherlands); Sonke, Jan-Jakob, E-mail: j.sonke@nki.nl [Department of Radiation Oncology, The Netherlands Cancer Institute-Antoni van Leeuwenhoek Hospital, Amsterdam (Netherlands)

    2012-03-01

    Purpose: To quantify the variability of diaphragm motion during free-breathing radiotherapy of lung patients and its effect on treatment margins to account for geometric uncertainties. Methods and Materials: Thirty-three lung cancer patients were analyzed. Each patient had 5-19 cone-beam scans acquired during different treatment fractions. The craniocaudal position of the diaphragm dome on the same side as the tumor was tracked over 2 min in the projection images, because it is both easily visible and a suitable surrogate to study the variability of the tumor motion and its impact on treatment margins. Intra-acquisition, inter-acquisition, and inter-patient variability of the respiratory cycles were quantified separately, as were the probability density functions (PDFs) of the diaphragm position over each cycle, each acquisition, and each patient. Asymmetric margins were simulated using each patient PDF and compared to symmetric margins computed from a margin recipe. Results: The peak-to-peak amplitude variability (1 SD) was 3.3 mm, 2.4 mm, and 6.1 mm for the intra-acquisition, inter-acquisition, and inter-patient variability, respectively. The average PDF of each cycle was similar to the sin{sup 4} function but the PDF of each acquisition was closer to a skew-normal distribution because of the motion variability. Despite large interfraction baseline variability, the PDF of each patient was generally asymmetric with a longer end-inhale tail because the end-exhale position was more stable than the end-inhale position. The asymmetry of the PDF required asymmetric margins around the time-averaged position to account for the position uncertainty but the average difference was 1.0 mm (range, 0.0-4.4 mm) for a sharp penumbra and an idealized online setup correction protocol. Conclusion: The respiratory motion is more irregular during the fractions than between the fractions. The PDF of the respiratory motion is asymmetrically distributed. Both the intra-acquisition variability and the PDF asymmetry have a limited impact on dose distributions and inferred margins. The use of a margin recipe to account for respiratory motion with an estimate of the average motion amplitude was adequate in almost all patients.

  1. Well injection valve with retractable choke

    SciTech Connect (OSTI)

    Pringle, R.E.

    1986-07-22

    An injection valve is described for use in a well conduit consisting of: a housing having a bore, a valve closure member in the bore moving between open and closed positions, a flow tube telescopically movable in the housing for controlling the movement of the valve closure member, means for biasing the flow tube in a direction for allowing the valve closure member to move to the closed position, an expandable and contractible fluid restriction connected to the flow tube and extending into the bore for moving the flow tube to the open position in response to injection fluid, but allowing the passage of well tools through the valve, the restriction contractible in response to fluid flow, the restriction includes, segments movable into and out of the bore, and biasing means yieldably urging the segments into the bore, a no-go shoulder on the flow tube, and releasable lockout means between the flow tube and the housing for locking the flow tube and valve in the open position.

  2. Inspecting coiled tubing for well operations

    SciTech Connect (OSTI)

    Gard, M.F.; Pasternack, E.S.; Smith, L.J.

    1992-02-18

    This patent describes improvement in a coiled tubing system for insertion of a substantially continuous bendable length of metal tubing into and withdrawal from a wellbore, the system including a tubing injection unit disposed for injecting the length of tubing into the well bore and storage means for dispensing the length of tubing and receiving the length of tubing from the injection unit. The improvement includes: tubing inspection apparatus for substantially continuously inspecting the wall section of the tubing to detect cracks and structural defects which may lead to tubing failure, the apparatus comprising: a source of electromagnetic radiation mounted in proximity to the tubing between the injection unit and a wellhead into which the tubing is injected; a radiation detector unit for receiving signals from the source which have been projected through the wall of the tubing; means for receiving signals form the detector unit for monitoring the structural integrity o the wall of the tubing during one of injecting and withdrawing the tubing with respect to the wellhead; and housing means supported for rotation about a longitudinal axis of the tubing.

  3. Light Water Reactor Sustainability Program Risk Informed Safety Margin Characterization (RISMC) Advanced Test Reactor Demonstration Case Study

    SciTech Connect (OSTI)

    Curtis Smith; David Schwieder; Cherie Phelan; Anh Bui; Paul Bayless

    2012-08-01

    Safety is central to the design, licensing, operation, and economics of Nuclear Power Plants (NPPs). Consequently, the ability to better characterize and quantify safety margin holds the key to improved decision making about LWR design, operation, and plant life extension. A systematic approach to characterization of safety margins and the subsequent margins management options represents a vital input to the licensee and regulatory analysis and decision making that will be involved. The purpose of the RISMC Pathway R&D is to support plant decisions for risk-informed margins management with the aim to improve economics, reliability, and sustain safety of current NPPs. Goals of the RISMC Pathway are twofold: (1) Develop and demonstrate a risk-assessment method coupled to safety margin quantification that can be used by NPP decision makers as part of their margin recovery strategies. (2) Create an advanced “RISMC toolkit” that enables more accurate representation of NPP safety margin. This report describes the RISMC methodology demonstration where the Advanced Test Reactor (ATR) was used as a test-bed for purposes of determining safety margins. As part of the demonstration, we describe how both the thermal-hydraulics and probabilistic safety calculations are integrated and used to quantify margin management strategies.

  4. Mapping the Potential for Biofuel Production on Marginal Lands: Differences in Definitions, Data and Models across Scales

    E-Print Network [OSTI]

    Lewis, Sarah M

    2014-01-01

    D. Land availability for biofuel production. Environ. Sci.of land available for biofuel production. Environ. Sci.so marginal land for biofuel crops is limited. Energy Policy

  5. Mapping the Potential for Biofuel Production on Marginal Lands: Differences in Definitions, Data and Models across Scales

    E-Print Network [OSTI]

    Lewis, Sarah M

    2014-01-01

    availability for biofuel production. Environ. Sci. Technol.of land available for biofuel production. Environ. Sci.the Potential for Biofuel Production on Marginal Lands:

  6. Heat Flow and Gas Hydrates on the Continental Margin of India: Building on Results from NGHP Expedition 01

    SciTech Connect (OSTI)

    Trehu, Anne; Kannberg, Peter

    2011-06-30

    The Indian National Gas Hydrate Program (NGHP) Expedition 01 presented the unique opportunity to constrain regional heat flow derived from seismic observations by using drilling data in three regions on the continental margin of India. The seismic bottom simulating reflection (BSR) is a well-documented feature in hydrate bearing sediments, and can serve as a proxy for apparent heat flow if data are available to estimate acoustic velocity and density in water and sediments, thermal conductivity, and seafloor temperature. Direct observations of temperature at depth and physical properties of the sediment obtained from drilling can be used to calibrate the seismic observations, decreasing the uncertainty of the seismically-derived estimates. Anomalies in apparent heat flow can result from a variety of sources, including sedimentation, erosion, topographic refraction and fluid flow. We constructed apparent heat flow maps for portions of the Krishna-Godavari (K-G) basin, the Mahanadi basin, and the Andaman basin and modeled anomalies using 1-D conductive thermal models. Apparent heat flow values in the Krishna-Godavari (K-G) basin and Mahanadi basin are generally 0.035 to 0.055 watts per square meter (W/m2). The borehole data show an increase in apparent heat flow as water depth increases from 900 to 1500 m. In the SW part of the seismic grid, 1D modeling of the effect of sedimentation on heat flow shows that ~50% of the observed increase in apparent heat flow with increasing water depth can be attributed to trapping of sediments behind a "toe-thrust" ridge that is forming along the seaward edge of a thick, rapidly accumulating deltaic sediment pile. The remainder of the anomaly can be explained either by a decrease in thermal conductivity of the sediments filling the slope basin or by lateral advection of heat through fluid flow along stratigraphic horizons within the basin and through flexural faults in the crest of the anticline. Such flow probably plays a role in bringing methane into the ridge formed by the toe-thrust. Because of the small anomaly due to this process and the uncertainty in thermal conductivity, we did not model this process explicitly. In the NE part of the K-G basin seismic grid, a number of local heat flow lows and highs are observed, which can be attributed to topographic refraction and to local fluid flow along faults, respectively. No regional anomaly can be resolved. Because of lack of continuity between the K-G basin sites within the seismic grid and those ~70 km to the NE in water depths of 1200 to 1500 m, we do not speculate on the reason for higher heat flow at these depths. The Mahanadi basin results, while limited in geographic extent, are similar to those for the KG basin. The Andaman basin exhibits much lower apparent heat flow values, ranging from 0.015 to 0.025 W/m2. Heat flow here also appears to increase with increasing water depth. The very low heat flow here is among the lowest heat flow observed anywhere and gives rise to a very thick hydrate stability zone in the sediments. Through 1D models of sedimentation (with extremely high sedimentation rates as a proxy for tectonic thickening), we concluded that the very low heat flow can probably be attributed to the combined effects of high sedimentation rate, low thermal conductivity, tectonic thickening of sediments and the cooling effect of a subducting plate in a subduction zone forearc. Like for the K-G basin, much of the local variability can be attributed to topography. The regional increase in heat flow with water depth remains unexplained because the seismic grid available to us did not extend far enough to define the local tectonic setting of the slope basin controlling this observational pattern. The results are compared to results from other margins, both active and passive. While an increase in apparent heat flow with increasing water depth is widely observed, it is likely a result of different processes in different places. The very low heat flow due to sedimentation and tectonics in the Andaman basin is at the low end of glob

  7. Heat Flow and Gas Hydrates on the Continental Margin of India: Building on Results from NGHP Expedition 01

    SciTech Connect (OSTI)

    Anne Trehu; Peter Kannberg

    2011-06-30

    The Indian National Gas Hydrate Program (NGHP) Expedition 01 presented the unique opportunity to constrain regional heat flow derived from seismic observations by using drilling data in three regions on the continental margin of India. The seismic bottom simulating reflection (BSR) is a well-documented feature in hydrate bearing sediments, and can serve as a proxy for apparent heat flow if data are available to estimate acoustic velocity and density in water and sediments, thermal conductivity, and seafloor temperature. Direct observations of temperature at depth and physical properties of the sediment obtained from drilling can be used to calibrate the seismic observations, decreasing the uncertainty of the seismically-derived estimates. Anomalies in apparent heat flow can result from a variety of sources, including sedimentation, erosion, topographic refraction and fluid flow. We constructed apparent heat flow maps for portions of the Krishna-Godavari (K-G) basin, the Mahanadi basin, and the Andaman basin and modeled anomalies using 1-D conductive thermal models. Apparent heat flow values in the Krishna-Godavari (K-G) basin and Mahanadi basin are generally 0.035 to 0.055 watts per square meter (W/m{sup 2}). The borehole data show an increase in apparent heat flow as water depth increases from 900 to 1500 m. In the SW part of the seismic grid, 1D modeling of the effect of sedimentation on heat flow shows that {approx}50% of the observed increase in apparent heat flow with increasing water depth can be attributed to trapping of sediments behind a 'toe-thrust' ridge that is forming along the seaward edge of a thick, rapidly accumulating deltaic sediment pile. The remainder of the anomaly can be explained either by a decrease in thermal conductivity of the sediments filling the slope basin or by lateral advection of heat through fluid flow along stratigraphic horizons within the basin and through flexural faults in the crest of the anticline. Such flow probably plays a role in bringing methane into the ridge formed by the toe-thrust. Because of the small anomaly due to this process and the uncertainty in thermal conductivity, we did not model this process explicitly. In the NE part of the K-G basin seismic grid, a number of local heat flow lows and highs are observed, which can be attributed to topographic refraction and to local fluid flow along faults, respectively. No regional anomaly can be resolved. Because of lack of continuity between the K-G basin sites within the seismic grid and those {approx}70 km to the NE in water depths of 1200 to 1500 m, we do not speculate on the reason for higher heat flow at these depths. The Mahanadi basin results, while limited in geographic extent, are similar to those for the K-G basin. The Andaman basin exhibits much lower apparent heat flow values, ranging from 0.015 to 0.025 W/m{sup 2}. Heat flow here also appears to increase with increasing water depth. The very low heat flow here is among the lowest heat flow observed anywhere and gives rise to a very thick hydrate stability zone in the sediments. Through 1D models of sedimentation (with extremely high sedimentation rates as a proxy for tectonic thickening), we concluded that the very low heat flow can probably be attributed to the combined effects of high sedimentation rate, low thermal conductivity, tectonic thickening of sediments and the cooling effect of a subducting plate in a subduction zone forearc. Like for the K-G basin, much of the local variability can be attributed to topography. The regional increase in heat flow with water depth remains unexplained because the seismic grid available to us did not extend far enough to define the local tectonic setting of the slope basin controlling this observational pattern. The results are compared to results from other margins, both active and passive. While an increase in apparent heat flow with increasing water depth is widely observed, it is likely a result of different processes in different places. The very low heat flow due to sedimentation and tectonics in the Andaman basi

  8. Optical panel system including stackable waveguides

    DOE Patents [OSTI]

    DeSanto, Leonard (Dunkirk, MD); Veligdan, James T. (Manorville, NY)

    2007-11-20

    An optical panel system including stackable waveguides is provided. The optical panel system displays a projected light image and comprises a plurality of planar optical waveguides in a stacked state. The optical panel system further comprises a support system that aligns and supports the waveguides in the stacked state. In one embodiment, the support system comprises at least one rod, wherein each waveguide contains at least one hole, and wherein each rod is positioned through a corresponding hole in each waveguide. In another embodiment, the support system comprises at least two opposing edge structures having the waveguides positioned therebetween, wherein each opposing edge structure contains a mating surface, wherein opposite edges of each waveguide contain mating surfaces which are complementary to the mating surfaces of the opposing edge structures, and wherein each mating surface of the opposing edge structures engages a corresponding complementary mating surface of the opposite edges of each waveguide.

  9. Thermovoltaic semiconductor device including a plasma filter

    DOE Patents [OSTI]

    Baldasaro, Paul F. (Clifton Park, NY)

    1999-01-01

    A thermovoltaic energy conversion device and related method for converting thermal energy into an electrical potential. An interference filter is provided on a semiconductor thermovoltaic cell to pre-filter black body radiation. The semiconductor thermovoltaic cell includes a P/N junction supported on a substrate which converts incident thermal energy below the semiconductor junction band gap into electrical potential. The semiconductor substrate is doped to provide a plasma filter which reflects back energy having a wavelength which is above the band gap and which is ineffectively filtered by the interference filter, through the P/N junction to the source of radiation thereby avoiding parasitic absorption of the unusable portion of the thermal radiation energy.

  10. New multilateral well architecture in heterogeneous reservoirs 

    E-Print Network [OSTI]

    Jia, Hongqiao

    2004-09-30

    Multilateral well technology has been widely used in the world oil fields. There still has technical limitation of these kinds of well structure. This thesis presents a new multilateral well architecture which is more ...

  11. INVITATIONAL WELL-TESTING SYMPOSIUM PROCEEDINGS

    E-Print Network [OSTI]

    Authors, Various

    2011-01-01

    Prior to spudding the well Drilling rate'is a direct meansGraves, E. D. , Jr. : Well Design: Drilling and Production,Density to Aid in Drilling Wells in High Pressure Areas.

  12. SW New Mexico Oil Well Formation Tops

    SciTech Connect (OSTI)

    Shari Kelley

    2015-10-21

    Rock formation top picks from oil wells from southwestern New Mexico from scout cards and other sources. There are differing formation tops interpretations for some wells, so for those wells duplicate formation top data are presented in this file.

  13. Industry survey for horizontal wells. Final report

    SciTech Connect (OSTI)

    Wilson, D.D.; Kaback, D.S. [CDM Federal Programs Corp., Denver, CO (United States); Denhan, M.E. [Westinghouse Savannah River Co., Aiken, SC (United States); Watkins, D. [CDM Federal Programs Corp., Aiken, SC (United States)

    1993-07-01

    An international survey of horizontal environmental wells was performed during May and June of 1993. The purpose of the survey was to provide the environmental industry with an inventory of horizontal environmental wells and information pertaining to the extent of the use of horizontal environmental wells, the variety of horizontal environmental well applications, the types of geologic and hydrogeologic conditions within which horizontal environmental wells have been installed, and the companies that perform horizontal environmental well installations. Other information, such as the cost of horizontal environmental well installations and the results of tests performed on the wells, is not complete but is provided as general information with the caveat that the information should not be used to compare drilling companies. The result of the survey is a catalogue of horizontal environmental wells that are categorized by the objective or use of the wells, the vertical depth of the wells, and the drilling company contracted to install the wells.

  14. Estimating Well Costs for Enhanced Geothermal System Applications

    SciTech Connect (OSTI)

    K. K. Bloomfield; P. T. Laney

    2005-08-01

    The objective of the work reported was to investigate the costs of drilling and completing wells and to relate those costs to the economic viability of enhanced geothermal systems (EGS). This is part of a larger parametric study of major cost components in an EGS. The possibility of improving the economics of EGS can be determined by analyzing the major cost components of the system, which include well drilling and completion. Determining what costs in developing an EGS are most sensitive will determine the areas of research to reduce those costs. The results of the well cost analysis will help determine the cost of a well for EGS development.

  15. 2013 strategic petroleum reserve big hill well integrity grading report.

    SciTech Connect (OSTI)

    Lord, David L.; Roberts, Barry L.; Lord, Anna C. Snider; Bettin, Giorgia; Sobolik, Steven Ronald; Park, Byoung Yoon; Rudeen, David Keith; Eldredge, Lisa; Wynn, Karen; Checkai, Dean; Perry, James Thomas

    2014-02-01

    This report summarizes the work performed in developing a framework for the prioritization of cavern access wells for remediation and monitoring at the Big Hill Strategic Petroleum Reserve site. This framework was then applied to all 28 wells at the Big Hill site with each well receiving a grade for remediation and monitoring. Numerous factors affecting well integrity were incorporated into the grading framework including casing survey results, cavern pressure history, results from geomechanical simulations, and site geologic factors. The framework was developed in a way as to be applicable to all four of the Strategic Petroleum Reserve sites.

  16. Wells Public Utilities - Commercial & Industrial Energy Efficiency...

    Broader source: Energy.gov (indexed) [DOE]

    Refrigeration Equipment Program Info Sector Name Utility Administrator Wells Public Utilities Website http:www.SaveEnergyInWells.com State Minnesota Program Type Rebate Program...

  17. The politics of marginality in Wallowa County, Oregon: Contesting the production of landscapes of consumption

    E-Print Network [OSTI]

    Kurapov, Alexander

    The politics of marginality in Wallowa County, Oregon: Contesting the production of landscapes of consumption Jesse B. Abrams a,b,*, Hannah Gosnell c a Department of Sociology, Whitman College, 345 Boyer Ave not only technical issues of land productivity, but also broader community contestations over

  18. Anomalous Tectonic Subsidence of the Southern Australian Passive Margin: Response to Cretaceous Dynamic Topography

    E-Print Network [OSTI]

    Müller, Dietmar

    Anomalous Tectonic Subsidence of the Southern Australian Passive Margin: Response to Cretaceous that formed over and orthogonal to a Mesozoic subducted slab in the mantle. The tectonic subsidence pattern, enhancing initial subsidence. Subsequent lithospheric rebound coincides with post-rift thermal subsidence

  19. Coral reef evolution on rapidly subsiding margins Jody M. Webster a,b,

    E-Print Network [OSTI]

    Riding, Robert

    Coral reef evolution on rapidly subsiding margins Jody M. Webster a,b, , Juan Carlos Braga d regions have experienced rapid subsidence (2­6 m/ka) over the last 500 ka. Rapid subsidence, combined sea-level changes, subsidence rates, accretion rates, basement substrates, and paleobathymetry

  20. Re-Dispatching Generation to Increase Power System Security Margin and Support Low Voltage Bus

    E-Print Network [OSTI]

    Re-Dispatching Generation to Increase Power System Security Margin and Support Low Voltage Bus by re-dispatching generator outputs, using a normal vector found at a voltage collapse boundary or a low voltage boundary (LVB). This method uses the normal vector as an indicator to change the generation

  1. The spiny lobster, Panulirus margin-atus, is endemic to the Hawaiian

    E-Print Network [OSTI]

    Hawai'i at Manoa, University of

    birds, monk seals, and reef fishes (Polo- vina et al., 1994). After the recruit- ment collapse132 The spiny lobster, Panulirus margin- atus, is endemic to the Hawaiian Archipelago and Johnston in the northwestern portion of the archipelago known as the Northwestern Hawaiian Islands (NWHI). From the early 1980s

  2. Leverage and Beliefs: Personal Experience and Risk Taking in Margin Lending*

    E-Print Network [OSTI]

    Straight, Aaron

    Leverage and Beliefs: Personal Experience and Risk Taking in Margin Lending* Peter Koudijs+ Hans of financial distress to address this question. An investor syndicate speculating in English stocks went times, and declining when asset prices fall (Adrian and Shin 2010). For example, when the stock market

  3. Abstract--Although Locational Marginal Pricing (LMP) plays an important role in many restructured wholesale power

    E-Print Network [OSTI]

    Tesfatsion, Leigh

    the performance of these markets. In this paper, different AC and DC optimal power flow (OPF) models are presented Terms-- Locational marginal pricing, wholesale power market, AC optimal power flow, DC optimal power to distinct local conditions (e.g., hydroelectric power in the northwest). Even in regions adopting the design

  4. Proceedings of the Combustion Institute, Volume 28, 2000/pp. 757763 EXPERIMENTAL DETERMINATION OF THE STABILITY MARGIN

    E-Print Network [OSTI]

    Lieuwen, Timothy C.

    757 Proceedings of the Combustion Institute, Volume 28, 2000/pp. 757­763 EXPERIMENTAL DETERMINATION the response of the combustion process heat release to driven flow oscillations and the response determine the stability margin of combustors. Such an approach would enable combustion engi- neers

  5. Between-ness: Theory and Practice within the Margins of Cathy Smith

    E-Print Network [OSTI]

    Boyd, Colin

    Between-ness: Theory and Practice within the Margins of Excess Cathy Smith Queensland University framework developed in a doctoral program of research concerned with connecting philosophies of between-ness between- ness; that which is neither one state nor the other but a zone of blurring in-between. An example

  6. Geologic hazards on the Atlantic continental margin of the United States

    SciTech Connect (OSTI)

    Folger, D.W.

    1985-01-01

    Although 46 exploratory holes have failed to reveal commercial hydrocarbon accumulations on the US Atlantic margin, about twice that number were drilled on the contiguous Canadian margin before large reserves were discovered. Thus, despite the initial results, exploration on the US margin will probably continue and additional information will be needed to augment the extensive environmental data base acquired over the past 10 years. The extent, timing, causes, and importance of sediment instability of the Continental Slopes of Georges Bank, Baltimore Canyon Trough and Carolina Trough--where future exploration will take place--remain controversial. Many question remain to be answered regarding such phenomena as creep on the upper slope, mass wasting in canyons and gullies, and slumping associated with faults and salt diapirs. Along the southeastern margin, the distribution of cavernous porosity below the shelf is only broadly known. Caverns pose a potential threat to drilling operations ranging from collapse of rigs to circulation loss and sheared drill strings. In deeper waters of the Continental Slope (700-2000 m), clathrates or frozen gas hydrates are common. The potential hazard of blow-outs from gas trapped beneath this layer are unknown. Additional information is needed to assess the bottom stresses imposed by tidal, storm, and geostrophically-driven currents on offshore rigs and structures, particularly in such areas as Georges Bank, the Carolina Trough, and the Blake Plateau.

  7. Marginal costs of freeway traffic congestion with on-road pollution exposure externality

    E-Print Network [OSTI]

    Bertini, Robert L.

    Marginal costs of freeway traffic congestion with on-road pollution exposure externality Alexander August 2012 Received in revised form 6 March 2013 Accepted 23 September 2013 Keywords: External costs Traffic congestion On-road In-vehicle Pollution exposure Vehicle emissions a b s t r a c t The health cost

  8. Water and energy footprints of bioenergy crop production on marginal lands

    E-Print Network [OSTI]

    Chen, Jiquan

    of Zoology, Michigan State University, East Lansing, MI 48824, USA Abstract Water and energy demandsWater and energy footprints of bioenergy crop production on marginal lands A . K . B H A R D WA J and S . K . H A M I LT O N *w} *Great Lakes Bioenergy Research Center, Michigan State University, East

  9. Systematic destruction of K-Feldspar in deeply buried rift and passive margin sandstones 

    E-Print Network [OSTI]

    Wilkinson, Mark; Milliken, Kitty; Haszeldine, Stuart

    2001-01-01

    Systematic patterns of detrital K-feldspar decline with increasing burial depth are revealed during deep burial (2.5-4.5km) of sandstones in diverse sedimentary basins from three rift and two passive margin setings in the North Sea and USA gulf...

  10. Interface effect in coupled quantum wells

    SciTech Connect (OSTI)

    Hao, Ya-Fei

    2014-06-28

    This paper intends to theoretically investigate the effect of the interfaces on the Rashba spin splitting of two coupled quantum wells. The results show that the interface related Rashba spin splitting of the two coupled quantum wells is both smaller than that of a step quantum well which has the same structure with the step quantum well in the coupled quantum wells. And the influence of the cubic Dresselhaus spin-orbit interaction of the coupled quantum wells is larger than that of a step quantum well. It demonstrates that the spin relaxation time of the two coupled quantum wells will be shorter than that of a step quantum well. As for the application in the spintronic devices, a step quantum well may be better than the coupled quantum wells, which is mentioned in this paper.

  11. Helicopter magnetic survey conducted to locate wells

    SciTech Connect (OSTI)

    Veloski, G.A.; Hammack, R.W.; Stamp, V.; Hall, R.; Colina, K.

    2008-07-01

    A helicopter magnetic survey was conducted in August 2007 over 15.6 sq mi at the Naval Petroleum Reserve No. 3’s (NPR-3) Teapot Dome Field near Casper, Wyoming. The survey’s purpose was to accurately locate wells drilled there during more than 90 years of continuous oilfield operation. The survey was conducted at low altitude and with closely spaced flight lines to improve the detection of wells with weak magnetic response and to increase the resolution of closely spaced wells. The survey was in preparation for a planned CO2 flood for EOR, which requires a complete well inventory with accurate locations for all existing wells. The magnetic survey was intended to locate wells missing from the well database and to provide accurate locations for all wells. The ability of the helicopter magnetic survey to accurately locate wells was accomplished by comparing airborne well picks with well locations from an intense ground search of a small test area.

  12. Engine lubrication circuit including two pumps

    DOE Patents [OSTI]

    Lane, William H.

    2006-10-03

    A lubrication pump coupled to the engine is sized such that the it can supply the engine with a predetermined flow volume as soon as the engine reaches a peak torque engine speed. In engines that operate predominately at speeds above the peak torque engine speed, the lubrication pump is often producing lubrication fluid in excess of the predetermined flow volume that is bypassed back to a lubrication fluid source. This arguably results in wasted power. In order to more efficiently lubricate an engine, a lubrication circuit includes a lubrication pump and a variable delivery pump. The lubrication pump is operably coupled to the engine, and the variable delivery pump is in communication with a pump output controller that is operable to vary a lubrication fluid output from the variable delivery pump as a function of at least one of engine speed and lubrication flow volume or system pressure. Thus, the lubrication pump can be sized to produce the predetermined flow volume at a speed range at which the engine predominately operates while the variable delivery pump can supplement lubrication fluid delivery from the lubrication pump at engine speeds below the predominant engine speed range.

  13. Broadening Industry Governance to Include Nonproliferation

    SciTech Connect (OSTI)

    Hund, Gretchen; Seward, Amy M.

    2008-11-11

    As industry is the first line of defense in detecting and thwarting illicit trade networks, the engagement of the private sector is critical to any government effort to strengthen existing mechanisms to protect goods and services throughout the supply chain. This study builds on previous PNNL work to continue to evaluate means for greater industry engagement to complement and strengthen existing governmental efforts to detect and stem the trade of illicit goods and to protect and secure goods that could be used in making a weapon of mass destruction. Specifically, the study evaluates the concept of Industry Self Regulation, defined as a systematic voluntary program undertaken by an industry or by individual companies to anticipate, implement, supplement, or substitute for regulatory requirements in a given field, generally through the adoption of best practices. Through a series of interviews with companies with a past history of non-compliance, trade associations and NGOs, the authors identify gaps in the existing regulatory infrastructure, drivers for a self regulation approach and the form such an approach might take, as well as obstacles to be overcome. The authors conclude that it is at the intersection of industry, government, and security that—through collaborative means—the effectiveness of the international nonproliferation system—can be most effectively strengthened to the mutual benefit of both government and the private sector. Industry has a critical stake in the success of this regime, and has the potential to act as an integrating force that brings together the existing mechanisms of the global nonproliferation regime: export controls, physical protection, and safeguards. The authors conclude that industry compliance is not enough; rather, nonproliferation must become a central tenant of a company’s corporate culture and be viewed as an integral component of corporate social responsibility (CSR).

  14. Method for contamination control and barrier apparatus with filter for containing waste materials that include dangerous particulate matter

    DOE Patents [OSTI]

    Pinson, P.A.

    1998-02-24

    A container for hazardous waste materials that includes air or other gas carrying dangerous particulate matter has incorporated barrier material, preferably in the form of a flexible sheet, and one or more filters for the dangerous particulate matter sealably attached to such barrier material. The filter is preferably a HEPA type filter and is preferably chemically bonded to the barrier materials. The filter or filters are preferably flexibly bonded to the barrier material marginally and peripherally of the filter or marginally and peripherally of air or other gas outlet openings in the barrier material, which may be a plastic bag. The filter may be provided with a backing panel of barrier material having an opening or openings for the passage of air or other gas into the filter or filters. Such backing panel is bonded marginally and peripherally thereof to the barrier material or to both it and the filter or filters. A coupling or couplings for deflating and inflating the container may be incorporated. Confining a hazardous waste material in such a container, rapidly deflating the container and disposing of the container, constitutes one aspect of the method of the invention. The chemical bonding procedure for producing the container constitutes another aspect of the method of the invention. 3 figs.

  15. Method for contamination control and barrier apparatus with filter for containing waste materials that include dangerous particulate matter

    DOE Patents [OSTI]

    Pinson, Paul A. (Idaho Falls, ID)

    1998-01-01

    A container for hazardous waste materials that includes air or other gas carrying dangerous particulate matter has incorporated in barrier material, preferably in the form of a flexible sheet, one or more filters for the dangerous particulate matter sealably attached to such barrier material. The filter is preferably a HEPA type filter and is preferably chemically bonded to the barrier materials. The filter or filters are preferably flexibly bonded to the barrier material marginally and peripherally of the filter or marginally and peripherally of air or other gas outlet openings in the barrier material, which may be a plastic bag. The filter may be provided with a backing panel of barrier material having an opening or openings for the passage of air or other gas into the filter or filters. Such backing panel is bonded marginally and peripherally thereof to the barrier material or to both it and the filter or filters. A coupling or couplings for deflating and inflating the container may be incorporated. Confining a hazardous waste material in such a container, rapidly deflating the container and disposing of the container, constitutes one aspect of the method of the invention. The chemical bonding procedure for producing the container constitutes another aspect of the method of the invention.

  16. Ness horizontal-well case study

    SciTech Connect (OSTI)

    Koonsman, T.L. (Mobil Exploration Norway Inc. (Norway)); Purpich, A.J. (Mobil North Sea Ltd. (United Kingdom))

    1992-10-01

    This paper reviews the reservoir management work that led to the recommendation to drill the Ness field horizontal well. It also discusses the poor well performance seen almost immediately after production began and the reasons for that well performance revealed by a postdrill reservoir simulation. Finally, the atypical logging responses observed in the well are discussed.

  17. Track 4: Employee Health and Wellness

    Office of Energy Efficiency and Renewable Energy (EERE)

    ISM Workshop Presentations Knoxville Convention Center, Knoxville, TN August 2009 Track 4: Employee Health and Wellness

  18. Method for polymer synthesis in a reaction well

    DOE Patents [OSTI]

    Brennan, Thomas M. (San Francisco, CA)

    1998-01-01

    A method of synthesis for building a polymer chain, oligonucleotides in particular, by sequentially adding monomer units to at least one solid support for growing and immobilizing a polymer chain thereon in a liquid reagent solution. The method includes the step of: A) depositing a liquid reagent in a reaction well (26) in contact with at least one solid support and at least one monomer unit of the polymer chain affixed to the solid support. The well (26) includes at least one orifice (74) extending into the well (26), and is of a size and dimension to form a capillary liquid seal to retain the reagent solution in the well (26) to enable polymer chain growth on the solid support. The method further includes the step of B) expelling the reagent solution from the well (26), while retaining the polymer chain therein. This is accomplished by applying a first gas pressure to the reaction well such that a pressure differential between the first gas pressure and a second gas pressure exerted on an exit (80) of the orifice (74) exceeds a predetermined amount sufficient to overcome the capillary liquid seal and expel the reagent solution from the well (26) through the orifice exit (80).

  19. Method for polymer synthesis in a reaction well

    DOE Patents [OSTI]

    Brennan, T.M.

    1998-09-29

    A method of synthesis is described for building a polymer chain, oligonucleotides in particular, by sequentially adding monomer units to at least one solid support for growing and immobilizing a polymer chain thereon in a liquid reagent solution. The method includes the step of: (A) depositing a liquid reagent in a reaction well in contact with at least one solid support and at least one monomer unit of the polymer chain affixed to the solid support. The well includes at least one orifice extending into the well, and is of a size and dimension to form a capillary liquid seal to retain the reagent solution in the well to enable polymer chain growth on the solid support. The method further includes the step of (B) expelling the reagent solution from the well, while retaining the polymer chain therein. This is accomplished by applying a first gas pressure to the reaction well such that a pressure differential between the first gas pressure and a second gas pressure exerted on an exit of the orifice exceeds a predetermined amount sufficient to overcome the capillary liquid seal and expel the reagent solution from the well through the orifice exit. 9 figs.

  20. A coke oven model including thermal decomposition kinetics of tar

    SciTech Connect (OSTI)

    Munekane, Fuminori; Yamaguchi, Yukio [Mitsubishi Chemical Corp., Yokohama (Japan); Tanioka, Seiichi [Mitsubishi Chemical Corp., Sakaide (Japan)

    1997-12-31

    A new one-dimensional coke oven model has been developed for simulating the amount and the characteristics of by-products such as tar and gas as well as coke. This model consists of both heat transfer and chemical kinetics including thermal decomposition of coal and tar. The chemical kinetics constants are obtained by estimation based on the results of experiments conducted to investigate the thermal decomposition of both coal and tar. The calculation results using the new model are in good agreement with experimental ones.

  1. Automated robotic equipment for ultrasonic inspection of pressurizer heater wells

    DOE Patents [OSTI]

    Nachbar, Henry D. (Ballston Lake, NY); DeRossi, Raymond S. (Amsterdam, NY); Mullins, Lawrence E. (Middle Grove, NY)

    1993-01-01

    A robotic device for remotely inspecting pressurizer heater wells is provided which has the advantages of quickly, precisely, and reliably acquiring data at reasonable cost while also reducing radiation exposure of an operator. The device comprises a prober assembly including a probe which enters a heater well, gathers data regarding the condition of the heater well and transmits a signal carrying that data; a mounting device for mounting the probe assembly at the opening of the heater well so that the probe can enter the heater well; a first motor mounted on the mounting device for providing movement of the probe assembly in an axial direction; and a second motor mounted on the mounting device for providing rotation of the probe assembly. This arrangement enables full inspection of the heater well to be carried out.

  2. Timing and magnitude of Miocene eustasy derived from the mixed siliciclastic-carbonate stratigraphic record of the northeastern Australian margin

    E-Print Network [OSTI]

    Leckie, Mark

    amplitude of sea-level change ice volume sequence stratigraphy Heterozoan carbonates Miocene ODP Leg 194 Eustasy is a key parameter to understand sedimentary sequences on continental margins and to reconstruct and timing of sequence formation on mixed carbonate-siliciclastic margins, and to estimate the amplitude

  3. Natural Hazards and Effects on Local Populations: Applications of NSF MARGINS research to hazards mitigation in Central America

    E-Print Network [OSTI]

    Marshall, Jeffrey S.

    Natural Hazards and Effects on Local Populations: Applications of NSF MARGINS research to hazards (Co-chair: NSF MARGINS Central American Geologic Hazards Working Group, 2001) In: Silver, E. and Dixon Zone and Subduction Factory Initiatives, 15 p., 2001. Natural Hazards & Effects on Local Populations

  4. Shelf sedimentation on a tectonically active margin: A modern sediment budget for Poverty continental shelf, New Zealand

    E-Print Network [OSTI]

    Fabrizio, Mary C.

    Shelf sedimentation on a tectonically active margin: A modern sediment budget for Poverty Available online xxxx Keywords: Waipaoa River continental margin shelf sedimentation 210 Pb geochronology 239,240 Pu geochronology sediment budget The combination of high sediment yields and the prevalence

  5. Ionic liquids, electrolyte solutions including the ionic liquids, and energy storage devices including the ionic liquids

    DOE Patents [OSTI]

    Gering, Kevin L.; Harrup, Mason K.; Rollins, Harry W.

    2015-12-08

    An ionic liquid including a phosphazene compound that has a plurality of phosphorus-nitrogen units and at least one pendant group bonded to each phosphorus atom of the plurality of phosphorus-nitrogen units. One pendant group of the at least one pendant group comprises a positively charged pendant group. Additional embodiments of ionic liquids are disclosed, as are electrolyte solutions and energy storage devices including the embodiments of the ionic liquid.

  6. Nitrogen Monitoring of West Hackberry 117 Cavern Wells.

    SciTech Connect (OSTI)

    Bettin, Giorgia; Lord, David

    2015-02-01

    U.S. Strategic Petroleum Reserve (SPR) oil storage cavern West Hackberry 117 was tested under extended nitrogen monitoring following a successful mechanical integrity test in order to validate a newly developed hydrostatic column model to be used to differentiate between normal "tight" well behavior and small-leak behavior under nitrogen. High resolution wireline pressure and temperature data were collected during the test period and used in conjunction with the hydrostatic column model to predict the nitrogen/oil interface and the pressure along the entire fluid column from the bradenhead flange nominally at ground surface to bottom of brine pool. Results here and for other SPR caverns have shown that wells under long term nitrogen monitoring do not necessarily pressurize with a relative rate (P N2 /P brine) of 1. The theoretical relative pressure rate depends on the well configuration, pressure and the location of the nitrogen-oil interface and varies from well to well. For the case of WH117 the predicted rates were 0.73 for well A and 0.92 for well B. The measured relative pressurization rate for well B was consistent with the model prediction, while well A rate was found to be between 0.58-0.68. A number of possible reasons for the discrepancy between the model and measured rates of well A are possible. These include modeling inaccuracy, measurement inaccuracy or the possibility of the presence of a very small leak (below the latest calculated minimum detectable leak rate).

  7. RTP as an Optional Service: It's Alive, But Is It Well?

    SciTech Connect (OSTI)

    Goldman, Charles; Barbose, Galen; Neenan, Bernie

    2006-03-10

    Economists have advocated for real-time pricing (RTP) of electricity on the basis of the gains in economic efficiency that would result from charging customers the contemporaneous marginal cost of supplying electricity instead of the average cost. In recent years, RTP has also become the subject of interest in a variety of policy contexts, including integrated resource planning initiatives, ongoing efforts to improve efficiency and reliability in competitive electricity markets, and implementation of default service in states with retail choice. Most experience with RTP has been as an optional service, that is, a self-selecting alternative to the standard utility service. By our count, approximately 70 utilities in the U.S. offered an optional RTP program at some point over the past 20 years. However, many programs are now defunct. In 2003, 47 utilities in the U.S. were still offering an optional RTP program, on either a pilot or permanent basis (see Figure 1). In addition, 10 utilities in states with retail choice currently offer RTP as the default service for large customers that are not under contract with a competitive supplier. Another two utilities have received regulatory approval to do so in the next few years. Although the results of a few optional RTP programs have been publicized, the vast majority of programs have operated in relative obscurity. To provide a wider perspective on utility and customer experience with RTP, we surveyed 43 optional RTP programs offered in 2003. We interviewed RTP program managers and other utility staff, and reviewed publicly available sources, including key regulatory documents and program evaluations. Based on this research, we identified trends related to RTP program history and outlook, program design and implementation, customer participation, and participant price response. The results are both surprising and instructive. We conclude that RTP is indeed alive but is not prospering as well it could. Thus, we offer a number of recommendations for policymakers and utilities that are considering optional RTP as a strategy for developing price responsive demand.

  8. Vapor port and groundwater sampling well

    DOE Patents [OSTI]

    Hubbell, J.M.; Wylie, A.H.

    1996-01-09

    A method and apparatus have been developed for combining groundwater monitoring wells with unsaturated-zone vapor sampling ports. The apparatus allows concurrent monitoring of both the unsaturated and the saturated zone from the same well at contaminated areas. The innovative well design allows for concurrent sampling of groundwater and volatile organic compounds (VOCs) in the vadose (unsaturated) zone from a single well, saving considerable time and money. The sample tubes are banded to the outer well casing during installation of the well casing. 10 figs.

  9. Vapor port and groundwater sampling well

    DOE Patents [OSTI]

    Hubbell, Joel M. (Idaho Falls, ID); Wylie, Allan H. (Idaho Falls, ID)

    1996-01-01

    A method and apparatus has been developed for combining groundwater monitoring wells with unsaturated-zone vapor sampling ports. The apparatus allows concurrent monitoring of both the unsaturated and the saturated zone from the same well at contaminated areas. The innovative well design allows for concurrent sampling of groundwater and volatile organic compounds (VOCs) in the vadose (unsaturated) zone from a single well, saving considerable time and money. The sample tubes are banded to the outer well casing during installation of the well casing.

  10. Fluid-Rock Characterization and Interactions in NMR Well Logging

    SciTech Connect (OSTI)

    Hirasaki, George J.; Mohanty, Kishore K.

    2003-02-10

    The objective of this project was to characterize the fluid properties and fluid-rock interactions that are needed for formation evaluation by NMR well logging. The advances made in the understanding of NMR fluid properties are summarized in a chapter written for an AAPG book on NMR well logging. This includes live oils, viscous oils, natural gas mixtures, and the relation between relaxation time and diffusivity.

  11. Fluid-Rock Characterization and Interactions in NMR Well Logging

    SciTech Connect (OSTI)

    Hirasaki, George J.; Mohanty, Kishore K.

    2003-02-10

    The objective of this project was to characterize the fluid properties and fluid-rock interactions which are needed for formation evaluation by NMR well logging. NMR well logging is finding wide use in formation evaluation. The formation parameters commonly estimated were porosity, permeability, and capillary bound water. Special cases include estimation of oil viscosity, residual oil saturation, location of oil/water contact, and interpretation on whether the hydrocarbon is oil or gas.

  12. seismic margin

    Office of Scientific and Technical Information (OSTI)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of NaturalDukeWakefield MunicipalTechnicalInformation4563 LLNL Small-scale Friction Sensitivityv b, iNOTICE OF OPEN CHANGE

  13. Horizontal well applications in complex carbonate reservoirs

    SciTech Connect (OSTI)

    Rahman, M.; Al-Awami, H.

    1995-10-01

    Over the past four years, Saudi Aramco has drilled over eighty horizontal wells, onshore and offshore. It has successfully applied this technology to develop new reservoirs as well as enhance recovery from its mature fields. This paper presents the reservoir engineering aspects of `horizontal` and `high angle` wells drilled in a major offshore field in Saudi Arabia. It shows how horizontal wells have (a) increased the recovery of bypassed oil, (b) improved well productivity in tight reservoirs, (c) increased production from thin oil zones underlain by water, and (d) improved peripheral injection. The paper discusses the actual performance of the horizontal wells and compares them with offset conventional wells. It presents the results of logging and testing of these wells, and highlights actual field data on (a) relationship between productivity gain and horizontal length, (b) pressure loss along the horizontal wellbore, and (c) effect of heterogeneity on coning an inflow performance.

  14. Disinfecting Water Wells by Shock Chlorination 

    E-Print Network [OSTI]

    Dozier, Monty; McFarland, Mark L.

    2005-09-30

    If your well has been flooded, it must be shock chlorinated before it can be used as a source of drinking water. This publication explains how to disinfect a well using either dry chlorine or liquid household bleach....

  15. Production Trends of Shale Gas Wells 

    E-Print Network [OSTI]

    Khan, Waqar A.

    2010-01-14

    To obtain better well performance and improved production from shale gas reservoirs, it is important to understand the behavior of shale gas wells and to identify different flow regions in them over a period of time. It is also important...

  16. RFI Well Integrity 06 JUL 1400

    Broader source: Energy.gov [DOE]

    This PowerPoint report entitled "Well Integrity During Shut - In Operations: DOE/DOI Analyses" describes risks and suggests risk management recommendations associated with shutting in the well.

  17. Groundwater Monitoring Well Installation Work Plan

    E-Print Network [OSTI]

    Groundwater Monitoring Well Installation Work Plan CSMRI Site Prepared for: Colorado School;CSMRI Site Groundwater Monitoring Well Installation Work Plan December 6, 2006 Page ii Table of Contents

  18. Knowledge-based stratigraphic well-log correlation 

    E-Print Network [OSTI]

    Denton, Michael A.

    1990-01-01

    correlated higher ranking strata. Thus, higher ranking correlations provide heuristics for lower ranking correlations. The system represents strata by symbols from a set of standard symbols which include peaks, troughs, and steps. Symbols replace events.... The zone attributes abstracted from the well-log include the following: interval, lithology ? classified as shale or non-shale, zone position, general zone shape, thickness, average amplitude, zone above name, and zone below name. Thus, the expert system...

  19. Capping of Water Wells for Future Use 

    E-Print Network [OSTI]

    Lesikar, Bruce J.; Mechell, Justin

    2007-09-04

    Water wells that are not being used, but that might be needed in the future, can be sealed with a cap that covers the top of the well casing pipe to prevent unauthorized access and contamination of the well. This publication explains how to cap a...

  20. Discrimination with error margin between two states - Case of general occurrence probabilities -

    E-Print Network [OSTI]

    H. Sugimoto; T. Hashimoto; M. Horibe; A. Hayashi

    2009-11-18

    We investigate a state discrimination problem which interpolates minimum-error and unambiguous discrimination by introducing a margin for the probability of error. We closely analyze discrimination of two pure states with general occurrence probabilities. The optimal measurements are classified into three types. One of the three types of measurement is optimal depending on parameters (occurrence probabilities and error margin). We determine the three domains in the parameter space and the optimal discrimination success probability in each domain in a fully analytic form. It is also shown that when the states to be discriminated are multipartite, the optimal success probability can be attained by local operations and classical communication. For discrimination of two mixed states, an upper bound of the optimal success probability is obtained.

  1. Workshop on Program for Elimination of Requirements Marginal to Safety: Proceedings

    SciTech Connect (OSTI)

    Dey, M. [Nuclear Regulatory Commission, Washington, DC (United States). Div. of Safety Issue Resolution; Arsenault, F.; Patterson, M.; Gaal, M. [SCIENTECH, Inc., Rockville, MD (United States)

    1993-09-01

    These are the proceedings of the Public Workshop on the US Nuclear Regulatory Commission`s Program for Elimination of Requirements Marginal to Safety. The workshop was held at the Holiday Inn, Bethesda, on April 27 and 28, 1993. The purpose of the workshop was to provide an opportunity for public and industry input to the program. The workshop addressed the institutionalization of the program to review regulations with the purpose of eliminating those that are marginal. The objective is to avoid the dilution of safety efforts. One session was devoted to discussion of the framework for a performance-based regulatory approach. In addition, panelists and attendees discussed scope, schedules and status of specific regulatory items: containment leakage testing requirements, fire protection requirements, requirements for environmental qualification of electrical equipment, requests for information under 10CFR50.54(f), requirements for combustible gas control systems, and quality assurance requirements.

  2. Completion Report for Well ER-EC-14, Corrective Action Units 101 and 102: Central and Western Pahute Mesa

    SciTech Connect (OSTI)

    2013-03-05

    Well ER-EC-14 was drilled for the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office in support of the Nevada Environmental Management Operations Underground Test Area (UGTA) Activity at the Nevada National Security Site (NNSS; formerly Nevada Test Site), Nye County, Nevada. The well was drilled in September and October 2012, as part of the Central and Western Pahute Mesa Corrective Action Unit Phase II drilling program. The primary purpose of the well was to provide detailed hydrogeologic information for the Fortymile Canyon composite hydrostratigraphic unit in the Timber Mountain moat area, within the Timber Mountain caldera complex, that will help address uncertainties within the Pahute Mesa–Oasis Valley hydrostratigraphic framework model. The main 55.9-centimeter (cm) hole was drilled to a total depth of 325.5 meters (m) and cased with 40.6-cm casing to 308.1 m. The hole diameter was then decreased to 37.5 cm, and drilling continued to a total depth of 724.8 m. The completion casing string, set to the depth of 690.9 m, consists of 16.8-cm stainless-steel casing hanging from 19.4-cm carbon-steel casing. The stainless-steel casing has two slotted intervals open to the Rainier Mesa Tuff. Two piezometer strings were installed in Well ER-EC-14. Both piezometer strings, each with one slotted interval, consist of 6.0-cm carbon-steel tubing at the surface, then cross over to 7.3-cm stainless-steel tubing just above the water table. The shallow piezometer string was landed at 507.8 m, and the deep piezometer string was landed at 688.6 m. Both piezometer strings are set to monitor groundwater within moderately to densely welded Rainier Mesa Tuff. Data collected during and shortly after hole construction include composite drill cuttings samples collected every 3.0 m, various geophysical logs, water quality (including tritium and other radionuclides) measurements, and water level measurements. The well penetrated 15.2 m of alluvium and 709.6 m of Tertiary volcanic rocks. The stratigraphy and general lithology were not as expected due to the position of Well ER-EC-14 relative to the buried caldera margins of the Timber Mountain caldera complex. The well is located inside the Rainier Mesa caldera, but outside the younger Ammonia Tanks caldera. On November 5, 2012, a preliminary fluid level in the shallow piezometer string was measured at the depth of 311.8 m. This water level depth was taken before installation of the bridge plug (to be placed within the main completion casing to separate the two slotted zones). Well development, hydrologic testing, and sampling, will be conducted at a later date. No tritium above levels detectable by field methods were encountered in this hole. All Fluid Management Plan (FMP) requirements for Well ER-EC-14 were met. Analysis of monitoring samples and FMP confirmatory samples indicated that fluids generated during drilling at Well ER-EC-14 met the FMP criteria for discharge to an unlined sump or designated infiltration area. All sanitary and hydrocarbon waste generated was properly handled and disposed of.

  3. Higher U.S. Crop Prices Trigger Little Area Expansion so Marginal Land for Biofuel Crops Is Limited

    SciTech Connect (OSTI)

    Swinton, S.; Babcock, Bruce; James, Laura; Bandaru, Varaprasad

    2011-06-12

    By expanding energy biomass production on marginal lands that are not currently used for crops, food price increases and indirect climate change effects can be mitigated. Studies of the availability of marginal lands for dedicated bioenergy crops have focused on biophysical land traits, ignoring the human role in decisions to convert marginal land to bioenergy crops. Recent history offers insights about farmer willingness to put non-crop land into crop production. The 2006-09 leap in field crop prices and the attendant 64% gain in typical profitability led to only a 2% increase in crop planted area, mostly in the prairie states

  4. The marginal leakage of some dental cements in humans: a PIXE-microbeam approach

    SciTech Connect (OSTI)

    Zadro, A.; Passi, P. [Dental School, Department of Dental Materials, University of Padua (Italy); Cavalleri, G. [Dental School, Department of Restorative Dentistry, University of Verona (Italy); Galassini, S.; Moschini, G.; Rossi, P. [INFN, Laboratori Nazionali di Legnaro (Italy)

    1999-06-10

    The marginal leakage and water absorption of dental cements and restorative materials has been investigated by many authors with several techniques, some of which led to valid results. However, no technique could give, by itself, information both on leakage and water absorption, as these measurements usually need different investigations. PIXE micro beam offers the possibility of investigating these two aspects at the same time, since it is possible to map a proper marker element. In the present study, cavities were made on 50 extracted human molars, then filled with five different temporary cements (IRM, Cavit W, Kalsogen, Fermit N, SuperEBA). The filled teeth were placed into a 5% silver nitrate solution, and after three days, one, two, three and four weeks were examined. The samples for microPIXE were prepared after embedding the teeth in epoxy resin, and sectioning and grinding them down to a thickness of about 1 mm. The sections were placed on metal holders, and examined with a scanning proton {mu}beam, in Legnaro (Italy) at the AN2000 LAB of INFN National Laboratories. The beam consisted of 2.4 MeV protons, it had a cross section of 1.5 micron in diameter and typical currents of the order of some {mu}A were used. The maps were obtained by an 'ad hoc' software with a McIntosh personal computer. Mapping of silver allowed to evaluate both the marginal leakage and the water absorption for each cement. The samples filled with Cavit W showed a great infiltration, as the tracing element was found in the cement bulk, along the margins and inside the cavity, while those filled with IRM and Kalsogen presented only a deposition of the tracing solution on the cement surface. SuperEBA showed a poor resistance against microleakage, because the marker element was only detected along the cavity margins. Fermit N showed the best marginal integrity, and on its surface no traces of siver were found. In this case the better resistance may be due to the resin present in the composition of the material.

  5. Well purge and sample apparatus and method

    DOE Patents [OSTI]

    Schalla, Ronald (Kennewick, WA); Smith, Ronald M. (Richland, WA); Hall, Stephen H. (Kennewick, WA); Smart, John E. (Richland, WA); Gustafson, Gregg S. (Redmond, WA)

    1995-01-01

    The present invention specifically permits purging and/or sampling of a well but only removing, at most, about 25% of the fluid volume compared to conventional methods and, at a minimum, removing none of the fluid volume from the well. The invention is an isolation assembly with a packer, pump and exhaust, that is inserted into the well. The isolation assembly is designed so that only a volume of fluid between the outside diameter of the isolation assembly and the inside diameter of the well over a fluid column height from the bottom of the well to the top of the active portion (lower annulus) is removed. The packer is positioned above the active portion thereby sealing the well and preventing any mixing or contamination of inlet fluid with fluid above the packer. Ports in the wall of the isolation assembly permit purging and sampling of the lower annulus along the height of the active portion.

  6. Well purge and sample apparatus and method

    DOE Patents [OSTI]

    Schalla, R.; Smith, R.M.; Hall, S.H.; Smart, J.E.; Gustafson, G.S.

    1995-10-24

    The present invention specifically permits purging and/or sampling of a well but only removing, at most, about 25% of the fluid volume compared to conventional methods and, at a minimum, removing none of the fluid volume from the well. The invention is an isolation assembly with a packer, pump and exhaust, that is inserted into the well. The isolation assembly is designed so that only a volume of fluid between the outside diameter of the isolation assembly and the inside diameter of the well over a fluid column height from the bottom of the well to the top of the active portion (lower annulus) is removed. The packer is positioned above the active portion thereby sealing the well and preventing any mixing or contamination of inlet fluid with fluid above the packer. Ports in the wall of the isolation assembly permit purging and sampling of the lower annulus along the height of the active portion. 8 figs.

  7. Lithologic descriptions and temperature profiles of five wells in the southwestern Valles caldera region, New Mexico

    SciTech Connect (OSTI)

    Shevenell, L.; Goff, F.; Miles, D.; Waibel, A.; Swanberg, C.

    1988-01-01

    The subsurface stratigraphy and temperature profiles of the southern and western Valles caldera region have been well constrained with the use of data from the VC-1, AET-4, WC 23-4, PC-1 and PC-2 wells. Data from these wells indicate that thermal gradients west of the caldera margin are between 110 and 140)degrees)C/km, with a maximum gradient occurring in the bottom of PC-1 equal to 240)degrees)C/km as a result of thermal fluid flow. Gradients within the caldera reach a maximum of 350)degrees)C/km, while the maximum thermal gradient measured southwest of the caldera in the thermal outflow plume is 140)degrees)C/km. The five wells exhibit high thermal gradients (>60)deghrees)C/km) resulting from high conductive heat flow associated with the Rio Grande rift and volcanism in the Valles caldera, as well as high convective heat flow associated with circulating geothermal fluids. Gamma logs run in four of the five wells appear to be of limited use for stratigraphic correlations in the caldera region. However, stratigraphic and temperature data from the five wells provide information about the structure and thermal regime of the southern and western Valles caldera region. 29 refs., 9 figs. 2 tabs.

  8. Cathodic protection of storage field well casings

    SciTech Connect (OSTI)

    Dabkowski, J.

    1986-01-01

    Downhole logging of gas storage field wells to determine cathodic protection (CP) levels is expensive and requires removing the well from service. A technique allowing the prediction of downhole CP levels by modeling combined with limiting field measurements would provide the industry with a cost-effective means of implementing and monitoring casing protection. A computer model has been developed for a cathodically protected well casing.

  9. Abstract The natural gas price surged in 2004. As a result, the marginal cost of some generators burning gas also rose sharply.

    E-Print Network [OSTI]

    Tolbert, Leon M.

    Abstract ­ The natural gas price surged in 2004. As a result, the marginal cost of some generators marginal cost, which is closely related to the natural gas price. Since gas units are usually the marginal the sensitivity of Var benefit with respect to generation cost. The U.S. natural gas industry has been

  10. Nuclear power plant cable materials : review of qualification and currently available aging data for margin assessments in cable performance.

    SciTech Connect (OSTI)

    Celina, Mathias Christopher; Gillen, Kenneth Todd; Lindgren, Eric Richard

    2013-05-01

    A selective literature review was conducted to assess whether currently available accelerated aging and original qualification data could be used to establish operational margins for the continued use of cable insulation and jacketing materials in nuclear power plant environments. The materials are subject to chemical and physical degradation under extended radiationthermal- oxidative conditions. Of particular interest were the circumstances under which existing aging data could be used to predict whether aged materials should pass loss of coolant accident (LOCA) performance requirements. Original LOCA qualification testing usually involved accelerated aging simulations of the 40-year expected ambient aging conditions followed by a LOCA simulation. The accelerated aging simulations were conducted under rapid accelerated aging conditions that did not account for many of the known limitations in accelerated polymer aging and therefore did not correctly simulate actual aging conditions. These highly accelerated aging conditions resulted in insulation materials with mostlyinert' aging processes as well as jacket materials where oxidative damage dropped quickly away from the air-exposed outside jacket surface. Therefore, for most LOCA performance predictions, testing appears to have relied upon heterogeneous aging behavior with oxidation often limited to the exterior of the cable cross-section - a situation which is not comparable with the nearly homogenous oxidative aging that will occur over decades under low dose rate and low temperature plant conditions. The historical aging conditions are therefore insufficient to determine with reasonable confidence the remaining operational margins for these materials. This does not necessarily imply that the existing 40-year-old materials would fail if LOCA conditions occurred, but rather that unambiguous statements about the current aging state and anticipated LOCA performance cannot be provided based on original qualification testing data alone. The non-availability of conclusive predictions for the aging conditions of 40-year-old cables implies that the same levels of uncertainty will remain for any re-qualification or extended operation of these cables. The highly variable aging behavior of the range of materials employed also implies that simple, standardized aging tests are not sufficient to provide the required aging data and performance predictions for all materials. It is recommended that focused studies be conducted that would yield the material aging parameters needed to predict aging behaviors under low dose, low temperature plant equivalent conditions and that appropriately aged specimens be prepared that would mimic oxidatively-aged 40- to 60- year-old materials for confirmatory LOCA performance testing. This study concludes that it is not sufficient to expose materials to rapid, high radiation and high temperature levels with subsequent LOCA qualification testing in order to predictively quantify safety margins of existing infrastructure with regard to LOCA performance. We need to better understand how cable jacketing and insulation materials have degraded over decades of power plant operation and how this aging history relates to service life prediction and the performance of existing equipment to withstand a LOCA situation.

  11. Quantifying reactor safety margins: Part 1: An overview of the code scaling, applicability, and uncertainty evaluation methodology

    SciTech Connect (OSTI)

    Boyack, B.E.; Duffey, R.B.; Griffith, P.; Katsma, K.R.; Lellouche, G.S.; Levy, S.; Rohatgi, U.S.; Wilson, G.E.; Wulff, W.; Zuber, N.

    1988-01-01

    In August 1988, the Nuclear Regulatory Commission (NRC) approved the final version of a revised rule on the acceptance of emergency core cooling systems (ECCS) entitled ''Emergency Core Cooling System; Revisions to Acceptance Criteria.'' The revised rule states an alternate ECCS performance analysis, based on best-estimate methods, may be used to provide more realistic estimates of plant safety margins, provided the licensee quantifies the uncertainty of the estimates and included that uncertainty when comparing the calculated results with prescribed acceptance limits. To support the revised ECCS rule, the NRC and its contractors and consultants have developed and demonstrated a method called the Code Scaling, Applicability, and Uncertainty (CSAU) evaluation methodology. It is an auditable, traceable, and practical method for combining quantitative analyses and expert opinions to arrive at computed values of uncertainty. This paper provides an overview of the CSAU evaluation methodology and its application to a postulated cold-leg, large-break loss-of-coolant accident in a Westinghouse four-loop pressurized water reactor with 17 /times/ 17 fuel. The code selected for this demonstration of the CSAU methodology was TRAC-PF1/MOD1, Version 14.3. 23 refs., 5 figs., 1 tab.

  12. What Is Well Yield? Private wells are frequently drilled in rural areas to

    E-Print Network [OSTI]

    Danforth, Bryan Nicholas

    1 What Is Well Yield? Private wells are frequently drilled in rural areas to supply water lowering the water level in the borehole below the pump intake is called the well yield. Low-yielding wells are generally considered wells that cannot meet the peak water demand for the home or farm. This fact sheet

  13. Dissecting the eastern margin of the Tibetan plateau : a study of landslides, erosion and river incision in a transient landscape

    E-Print Network [OSTI]

    Ouimet, William Burke

    2007-01-01

    The eastern margin of the Tibetan plateau is characterized by large rivers dissecting regional topography that has been uplifted in association with the continued convergence of the Indian subcontinent and Eurasia. In this ...

  14. Portable Optical Fiber Probe-Based Spectroscopic Scanner for Rapid Cancer Diagnosis: A New Tool for Intraoperative Margin Assessment

    E-Print Network [OSTI]

    Yu, Chung-Chieh

    There continues to be a significant clinical need for rapid and reliable intraoperative margin assessment during cancer surgery. Here we describe a portable, quantitative, optical fiber probe-based, spectroscopic tissue ...

  15. Guaranteed margins and performance for an adaptive flight control system and application on the X-15 research airplane

    E-Print Network [OSTI]

    Dydek, Zachary Thompson

    2007-01-01

    The design tools developed for use with linear controllers such as gain and phase margins do not apply to nonlinear control architectures such as adaptive control. For decades, flight control engineers have used these tools ...

  16. Upgrading of substandard housing in Portugal : planning strategies for the technical improvement of marginal settlements, case study, the Casal Ventoso

    E-Print Network [OSTI]

    De Castello-Branco, Fernando N. B

    1983-01-01

    The primary scope of this thesis is to deal, from a technical standpoint, with the implementation of the upgrading concept in marginal settlements in Portugal. It consists mainly of two parts: The rationale of the concept, ...

  17. Evolution of oceanic margins : rifting in the Gulf of California and sediment diapirism and mantle hydration during subduction

    E-Print Network [OSTI]

    Miller, Nathaniel Clark

    2013-01-01

    This thesis investigates three processes that control the evolution of oceanic margins. Chapter 2 presents seismic images of a ~2-km-thick evaporite body in Guaymas Basin, central Gulf of California. In rifts, evaporites ...

  18. A comparison of the marginal adaptation of cathode-arc vapor-deposited titanium and cast base metal copings.

    E-Print Network [OSTI]

    Wu, Jean C; Lai, Li-Chung; Sheets, Cherilyn G; Earthman, James; Newcomb, Robert

    2011-01-01

    Marginal fit of gold inlay castings. J Prosthet Dent 1966;filling and porosity in castings of titanium. Dent Matera b Wu et al alloy types, casting procedures, por- celain

  19. Gas condensate damage in hydraulically fractured wells 

    E-Print Network [OSTI]

    Adeyeye, Adedeji Ayoola

    2004-09-30

    This project is a research into the effect of gas condensate damage in hydraulically fractured wells. It is the result of a problem encountered in producing a low permeability formation from a well in South Texas owned by the El Paso Production...

  20. Program Termination and Well Partial Orderings

    E-Print Network [OSTI]

    Blass, Andreas R.

    Program Termination and Well Partial Orderings Andreas Blass Yuri Gurevich Abstract The following observation may be useful in establishing program termination: if a transitive relation R is covered of the stature P of a well partial ordering P and show that |R| 1 × · · · × n and that this bound is tight

  1. Coiled tubing velocity strings keep wells unloaded

    SciTech Connect (OSTI)

    Wesson, H.R.; Shursen, J.L.

    1989-07-01

    Liquid loading is a problem in many older and even some newer gas wells, particularly in pressure depletion type reservoirs. This liquid loading results in decreased production and may even kill the well. The use of coiled tubing as a velocity string (or siphon string) has proved to be an economically viable alternative to allow continued and thus, increased cumulative production for wells experiencing liquid loading problems. Coiled tubing run inside the existing production string reduces the flow area, whether the well is produced up the tubing or up the annulus. This reduction in flow area results in an increase in flow velocity and thus, an increase in the well's ability to unload fluids.

  2. Monitoring cathodic protection of well casings

    SciTech Connect (OSTI)

    Dabkowski, J.

    1980-01-01

    Because conventional downhole logging of gas storage wells to determine cathodic-protection levels is expensive and inconvenient, a program was developed (1) to predict downhole casing-to-soil potentials from wellhead measurements in the presence of interference and (2 )to model the mutual interference effects occurring between the wells and the cathodic-protection systems. In the first phase of this project, a transmission-line model that was developed to represent the well casing electrically adequately predicted the downhole potentials for both ideal and nonideal polarization conditions. By allowing the number of sections used and their parameter values as variables, the model can accommodate different environments and casing configurations. The model's representation of a well casing by a lumped-parameter electrical network will also permit interference studies between mutually coupled wells.

  3. Recovery Boiler Modeling: An Improved Char Burning Model Including Sulfate Reduction and Carbon Removal 

    E-Print Network [OSTI]

    Grace, T. M.; Wag, K. J.; Horton, R. R.; Frederick, W. J.

    1994-01-01

    This paper describes an improved model of char burning during black liquor combustion that is capable of predicting net rates of sulfate reduction to sulfide as well as carbon burnup rates. Enhancements include a proper ...

  4. The Moho: Boundary above upper mantle peridotites or lower crustal eclogites? A global review and new interpretations for passive margins

    E-Print Network [OSTI]

    Müller, Dietmar

    and new interpretations for passive margins Rolf Mjelde a, , Alexey Goncharov b , R. Dietmar Müller c, Building F05, NSW 2006, Australia a b s t r a c ta r t i c l e i n f o Article history: Received 21 July: Eclogites Moho Wide-angle seismic Passive margins We have performed a global study of 2D crustal scale wide

  5. Pressure buildup characteristics in Austin Chalk wells 

    E-Print Network [OSTI]

    Claycomb, Eddy

    1982-01-01

    hole pressure instruments used to collect data were of the Amerada-gauge type. The instruments were either a RPG-3 (1-1/4" dia. ) or a RPG-4 (1" dia. ). The gauges consist of three basic parts: the recording section, a clock and either a pressure... stimulation was designed and performed on the well. Five months after the fracture stimulation and continuous production, the well had flow rates in excess of 1. 7 mmscf per day and 170 bbls, of oil per day. Case II: Conductive H draulic Fracture Well...

  6. Nevada Test Site Groundwater Well Rehabilitation Plan

    SciTech Connect (OSTI)

    David B. Hudson

    2006-12-01

    This plan describes actions to improve the utility and credibility of the Nevada Test Site (NTS) interim groundwater monitoring program. The two principal actions are: (1) well maintenance/rehabilitation activities and (2) the deployment of dedicated low-cost and reliable jack-pumps for groundwater sampling from deep monitoring wells. The scope of this proposal is to perform these actions on some number of nine selected wells (Figure 1) to evaluate whether these actions are achievable, practical, cost effective, and result in improved groundwater data quality.

  7. Marginal Cost of Steam and Power from Cogeneration Systems Using a Rational Value-Allocation Procedure 

    E-Print Network [OSTI]

    Kumana, J. D.; Al-Gwaiz, M. M.

    2004-01-01

    operate in either modes 1a or 2a, as electric utility companies are loathe to purchase surplus power from a cogenerator unless it is priced substantially below the utility?s own cheapest marginal cost of production. Usually, the cogenerator cannot... will invariably be positive. Can we be assured that the foregoing conclusion is correct? Not really. For example, one could argue that the decision to hold electrical power prices fixed is arbitrary, and that it is equally valid to fix the steam price...

  8. Groundwater well with reactive filter pack

    DOE Patents [OSTI]

    Gilmore, T.J.; Holdren, G.R. Jr.; Kaplan, D.I.

    1998-09-08

    A method and apparatus are disclosed for the remediation of contaminated soil and ground water wherein a reactive pack material is added to the annular fill material utilized in standard well construction techniques. 3 figs.

  9. Groundwater well with reactive filter pack

    DOE Patents [OSTI]

    Gilmore, Tyler J. (Pasco, WA); Holdren, Jr., George R. (Kennewick, WA); Kaplan, Daniel I. (Richland, WA)

    1998-01-01

    A method and apparatus for the remediation of contaminated soil and ground water wherein a reactive pack material is added to the annular fill material utilized in standard well construction techniques.

  10. Completion of Oil Wells May 4, 2003

    E-Print Network [OSTI]

    Rudge, John

    Completion of Oil Wells John Rudge May 4, 2003 1 Introduction After the initial drilling of an oil for given , z; i.e. ignore radial variation. Under this assumption these equations can be easily integrated

  11. Modeling techniques for simulating well behavior 

    E-Print Network [OSTI]

    Rattu, Bungen Christina

    2002-01-01

    This thesis is a catalog of modeling techniques useful in simulating well behavior in certain types of reservoirs that are often encountered in petroleum reservoirs. Emphasis has been placed on techniques that can be used with any conventional...

  12. Subsea tree cap well choke system

    SciTech Connect (OSTI)

    Bednar, J.M.

    1991-04-30

    This patent describes an apparatus useful in subsea well completions requiring a subsea choke. It comprises: a wellhead connector; a tree flow passage; a tree annulus passage; a tree cap; a choke; and a production line.

  13. Well-being and Philosophy of Science

    E-Print Network [OSTI]

    Alexandrova, Anna

    2015-03-06

    determinants and risk factors at biological, psychological and social levels (Diener 2012). Well-being is no longer thought to be an idiosyncratic personal phenomenon that does not admit of population-level analysis. Connected to this, there is a growing... simple division of labor: philosophers (or scientists in their philosophical moments) do the foundational normative work by telling us what well-being is, while scientists (or philosophers in their empirical moments) investigate the network of causes...

  14. PrimeEnergy/DOE/GRI slant well

    SciTech Connect (OSTI)

    Drimal, C.E.; Muncey, G.; Carden, R.

    1991-12-01

    This report presents final results of the Sterling Boggs 1240 slant well. Objectives of the project were (1) to test the potential for improved recovery efficiency in a fractured Devonian Shale reservoir from a directionally drilled well, (2) to perform detailed tests of reservoir properties and completion methods, and (3) to provide technology to industry which may ultimately improve the economics of drilling in the Devonian Shale and thereby stimulate development of its resources.

  15. Energy-conserving perennial agriculture for marginal land in southern Appalachia. Final technical report

    SciTech Connect (OSTI)

    Williams, G.

    1982-01-30

    USDA economists predict the end of surplus farm production in the US within this decade. More and more marginal land will be cropped to provide feed for the growing world population and to produce energy. Much of this potential cropland in Southern Appalachia is poorly suited to annual crops, such as corn. Perennial crops are much better suited to steep, rocky, and wet sites. Research was undertaken on the theoretical potentials of perennial species with high predicted yields of protein, carbohydrates, or oils. Several candidate staple perennial crops for marginal land in Southern Appalachia were identified, and estimates were made of their yields, energy input requirements, and general suitabilities. Cropping systems incorporating honeylocust, persimmon, mulberry, jujube, and beech were compared with corn cropping systems. It appears that these candidate staple perennials show distinct advantages for energy conservation and environmental preservation. Detailed economic analyses must await actual demonstration trials, but preliminary indications for ethanol conversion systems with honeylocust are encouraging. It is suggested that short-term loans to farmers undertaking this new type of agriculture would be appropriate to solve cash-flow problems.

  16. Geopressured-geothermal well report. Volume I. Drilling and completion

    SciTech Connect (OSTI)

    Not Available

    1982-01-01

    Gladys McCall site activities are covered through the completion of the test well and salt water disposal well. The test well was drilled to a total depth of 16,510 feet, then plugged back to 15,831 feet. Three 4'' diameter diamond cores were taken for analysis. An existing well on site, the Getty-Butts Gladys McCall No. 1, was reentered and completed to a depth of 3514 feet as a salt water disposal well. The geologic interpretation of the Gladys McCall site indicated target sands for testing at 15,080 feet through 15, 831 feet. Reservoir fluid temperature at this depth is estimated to be approximately 313/sup 0/F and pressure is estimated to be +-12,800 psi. The preliminary reservoir volume estimate is 3.6 billion barrels of brine. The design wells program includes environmental monitoring of the Gladys McCall site by Louisiana State University. Field stations are set up to monitor surface and ground water quality, subsidence, land loss and shoreline erosion, and seismicity. As of December 31, 1981 the study shows no significant impact on the environment by site operations.

  17. Productivity and Injectivity of Horizontal Wells

    SciTech Connect (OSTI)

    Arababi, Sepehr; Aziz, Khalid; Hayashida, Yasuyuki; Hewett, Thomas

    1999-11-08

    This quarterly report is based on the last activity above. It gives a brief account of the work and the complete study will be included in the next Annual Report of the project.

  18. Imbibition well stimulation via neural network design

    DOE Patents [OSTI]

    Weiss, William (Socorro, NM)

    2007-08-14

    A method for stimulation of hydrocarbon production via imbibition by utilization of surfactants. The method includes use of fuzzy logic and neural network architecture constructs to determine surfactant use.

  19. Testing of the Pleasant Bayou Well through October 1990

    SciTech Connect (OSTI)

    Randolph, P.L.; Hayden, C.G.; Mosca, V.L.; Anhaiser, J.L.

    1992-08-01

    Pleasant Bayou location was inactive from 1983 until the cleanout of the production and disposal wells in 1986. The surface facilities were rehabilitated and after shakedown of the system, additional repair of wellhead valves, and injection of an inhibitor pill, continuous long-term production was started in 1988. Over two years of production subsequent to that are reviewed here, including: production data, brine sampling and analysis, hydrocarbon sampling and analysis, solids sampling and analysis, scale control and corrosion monitoring and control.

  20. Nonclassical Light from Semiconductor Quantum Wells

    E-Print Network [OSTI]

    P. Grünwald; W. Vogel

    2014-05-06

    The fluorescence light from semiconductor quantum wells is analyzed with respect to its quantum optical properties. The light emitted by the excitons is described by bosonic excitations with a Kerr-type nonlinear interaction. To create the excitons, the incoming pump laser light is absorbed and the absorption acts as a spectral filter for the emitted light. The quantum properties of the emitted light are analyzed for the bare excitonic and the quantum-well systems. Squeezing of the quantum-well fluorescence persists for higher pump laser powers than the squeezing of the excitonic fluorescence. For strong pumping, the nonlinearity suppresses the creation of photon pairs and the photon statistics becomes sub-Poisson.

  1. Method and apparatus for sampling low-yield wells

    DOE Patents [OSTI]

    Last, George V. (Richland, WA); Lanigan, David C. (Kennewick, WA)

    2003-04-15

    An apparatus and method for collecting a sample from a low-yield well or perched aquifer includes a pump and a controller responsive to water level sensors for filling a sample reservoir. The controller activates the pump to fill the reservoir when the water level in the well reaches a high level as indicated by the sensor. The controller deactivates the pump when the water level reaches a lower level as indicated by the sensors. The pump continuously activates and deactivates the pump until the sample reservoir is filled with a desired volume, as indicated by a reservoir sensor. At the beginning of each activation cycle, the controller optionally can select to purge an initial quantity of water prior to filling the sample reservoir. The reservoir can be substantially devoid of air and the pump is a low volumetric flow rate pump. Both the pump and the reservoir can be located either inside or outside the well.

  2. Nuclear Arms Control R&D Consortium includes Los Alamos

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Nuclear Arms Control R&D Consortium includes Los Alamos Nuclear Arms Control R&D Consortium includes Los Alamos A consortium led by the University of Michigan that includes LANL as...

  3. Pseudo energy wells in active systems

    E-Print Network [OSTI]

    Raman Sheshka; Pierre Recho; Lev Truskinovsky

    2015-09-09

    Active stabilization in systems with zero or negative stiffness is an essential element of a wide variety of biological processes. We study a prototypical example of this phenomenon at a micro-scale and show how active rigidity, interpreted as a formation of a pseudo-well in the effective energy landscape, can be generated in an overdamped ratchet-type stochastic system. We link the transition from negative to positive rigidity with correlations in the noise and show that subtle differences in out-of-equilibrium driving may compromise the emergence of a pseudo-well.

  4. Resonator-quantum well infrared photodetectors

    SciTech Connect (OSTI)

    Choi, K. K. Sun, J.; Olver, K.; Jhabvala, M. D.; Jhabvala, C. A.; Waczynski, A.

    2013-11-11

    We applied a recent electromagnetic model to design the resonator-quantum well infrared photodetector (R-QWIP). In this design, we used an array of rings as diffractive elements to diffract normal incident light into parallel propagation and used the pixel volume as a resonator to intensify the diffracted light. With a proper pixel size, the detector resonates at certain optical wavelengths and thus yields a high quantum efficiency (QE). To test this detector concept, we fabricated a number of R-QWIPs with different quantum well materials and detector geometries. The experimental result agrees satisfactorily with the prediction, and the highest QE achieved is 71%.

  5. Pseudo energy wells in active systems

    E-Print Network [OSTI]

    Sheshka, Raman; Truskinovsky, Lev

    2015-01-01

    Active stabilization in systems with zero or negative stiffness is an essential element of a wide variety of biological processes. We study a prototypical example of this phenomenon at a micro-scale and show how active rigidity, interpreted as a formation of a pseudo-well in the effective energy landscape, can be generated in an overdamped ratchet-type stochastic system. We link the transition from negative to positive rigidity with correlations in the noise and show that subtle differences in out-of-equilibrium driving may compromise the emergence of a pseudo-well.

  6. cDNA encoding a polypeptide including a hevein sequence

    DOE Patents [OSTI]

    Raikhel, Natasha V. (Okemos, MI); Broekaert, Willem F. (Dilbeek, BE); Chua, Nam-Hai (Scarsdale, NY); Kush, Anil (New York, NY)

    1999-05-04

    A cDNA clone (HEV1) encoding hevein was isolated via polymerase chain reaction (PCR) using mixed oligonucleotides corresponding to two regions of hevein as primers and a Hevea brasiliensis latex cDNA library as a template. HEV1 is 1018 nucleotides long and includes an open reading frame of 204 amino acids. The deduced amino acid sequence contains a putative signal sequence of 17 amino acid residues followed by a 187 amino acid polypeptide. The amino-terminal region (43 amino acids) is identical to hevein and shows homology to several chitin-binding proteins and to the amino-termini of wound-induced genes in potato and poplar. The carboxyl-terminal portion of the polypeptide (144 amino acids) is 74-79% homologous to the carboxyl-terminal region of wound-inducible genes of potato. Wounding, as well as application of the plant hormones abscisic acid and ethylene, resulted in accumulation of hevein transcripts in leaves, stems and latex, but not in roots, as shown by using the cDNA as a probe. A fusion protein was produced in E. coli from the protein of the present invention and maltose binding protein produced by the E. coli.

  7. cDNA encoding a polypeptide including a hevein sequence

    DOE Patents [OSTI]

    Raikhel, N.V.; Broekaert, W.F.; Chua, N.H.; Kush, A.

    1999-05-04

    A cDNA clone (HEV1) encoding hevein was isolated via polymerase chain reaction (PCR) using mixed oligonucleotides corresponding to two regions of hevein as primers and a Hevea brasiliensis latex cDNA library as a template. HEV1 is 1018 nucleotides long and includes an open reading frame of 204 amino acids. The deduced amino acid sequence contains a putative signal sequence of 17 amino acid residues followed by a 187 amino acid polypeptide. The amino-terminal region (43 amino acids) is identical to hevein and shows homology to several chitin-binding proteins and to the amino-termini of wound-induced genes in potato and poplar. The carboxyl-terminal portion of the polypeptide (144 amino acids) is 74--79% homologous to the carboxyl-terminal region of wound-inducible genes of potato. Wounding, as well as application of the plant hormones abscisic acid and ethylene, resulted in accumulation of hevein transcripts in leaves, stems and latex, but not in roots, as shown by using the cDNA as a probe. A fusion protein was produced in E. coli from the protein of the present invention and maltose binding protein produced by the E. coli. 12 figs.

  8. cDNA encoding a polypeptide including a hevein sequence

    DOE Patents [OSTI]

    Raikhel, N.V.; Broekaert, W.F.; Chua, N.H.; Kush, A.

    1995-03-21

    A cDNA clone (HEV1) encoding hevein was isolated via polymerase chain reaction (PCR) using mixed oligonucleotides corresponding to two regions of hevein as primers and a Hevea brasiliensis latex cDNA library as a template. HEV1 is 1,018 nucleotides long and includes an open reading frame of 204 amino acids. The deduced amino acid sequence contains a putative signal sequence of 17 amino acid residues followed by a 187 amino acid polypeptide. The amino-terminal region (43 amino acids) is identical to hevein and shows homology to several chitin-binding proteins and to the amino-termini of wound-induced genes in potato and poplar. The carboxyl-terminal portion of the polypeptide (144 amino acids) is 74--79% homologous to the carboxyl-terminal region of wound-inducible genes of potato. Wounding, as well as application of the plant hormones abscisic acid and ethylene, resulted in accumulation of hevein transcripts in leaves, stems and latex, but not in roots, as shown by using the cDNA as a probe. A fusion protein was produced in E. coli from the protein of the present invention and maltose binding protein produced by the E. coli. 11 figures.

  9. CDNA encoding a polypeptide including a hevein sequence

    DOE Patents [OSTI]

    Raikhel, Natasha V. (Okemos, MI); Broekaert, Willem F. (Dilbeek, BE); Chua, Nam-Hai (Scarsdale, NY); Kush, Anil (New York, NY)

    1995-03-21

    A cDNA clone (HEV1) encoding hevein was isolated via polymerase chain reaction (PCR) using mixed oligonucleotides corresponding to two regions of hevein as primers and a Hevea brasiliensis latex cDNA library as a template. HEV1 is 1018 nucleotides long and includes an open reading frame of 204 amino acids. The deduced amino acid sequence contains a putative signal sequence of 17 amino acid residues followed by a 187 amino acid polypeptide. The amino-terminal region (43 amino acids) is identical to hevein and shows homology to several chitin-binding proteins and to the amino-termini of wound-induced genes in potato and poplar. The carboxyl-terminal portion of the polypeptide (144 amino acids) is 74-79% homologous to the carboxyl-terminal region of wound-inducible genes of potato. Wounding, as well as application of the plant hormones abscisic acid and ethylene, resulted in accumulation of hevein transcripts in leaves, stems and latex, but not in roots, as shown by using the cDNA as a probe. A fusion protein was produced in E. coli from the protein of the present invention and maltose binding protein produced by the E. coli.

  10. Newport News in Review, ch. 47, segment includes TEDF groundbreaking...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    https:www.jlab.orgnewsarticlesnewport-news-review-ch-47-segment-includes-tedf-groundbreaking-event Newport News in Review, ch. 47, segment includes TEDF groundbreaking event...

  11. Solar Energy Education. Reader, Part II. Sun story. [Includes...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Part II. Sun story. Includes glossary Citation Details In-Document Search Title: Solar Energy Education. Reader, Part II. Sun story. Includes glossary You are...

  12. Microfluidic devices and methods including porous polymer monoliths...

    Office of Scientific and Technical Information (OSTI)

    devices and methods including porous polymer monoliths Citation Details In-Document Search Title: Microfluidic devices and methods including porous polymer monoliths Microfluidic...

  13. Reservoir studies of new multilateral well architecture 

    E-Print Network [OSTI]

    Sarfare, Manoj Dnyandeo

    2004-09-30

    solutions to these problems and prove to be the most likely tool to propel the industry in the next century. In this research we propose a new multilateral well architecture for more efficient and effective field drainage. We study the architecture from a...

  14. Geometrical Music Theory Rachel Wells Hall1

    E-Print Network [OSTI]

    Hall, Rachel W.

    Geometrical Music Theory Rachel Wells Hall1 Music theorists have frequently invoked geometry in modeling musical objects such as chords, rhythms, and scales; however, no unified geometric perspective has musical terms can be understood as expressing symmetries of n-dimensional space. Identifying-- "gluing

  15. Foolproof completions for high rate production wells 

    E-Print Network [OSTI]

    Tosic, Slavko

    2009-05-15

    wells, particularly those with subsea wellheads, and the alternative has been to subject the completion to increasingly high drawdown, accepting a high skin effect. A far better solution is to use a HPF completion. Of course the execution of a successful...

  16. T2WELL/ECO2N

    Energy Science and Technology Software Center (OSTI)

    002966IBMPC00 T2Well/ECO2N Version 1.0: Multiphase and Non-Isothermal Model for Coupled Wellbore-Reservoir Flow of Carbon Dioxide and Variable Salinity Water  http:..esd.lbl.gov/tough/licensing.html 

  17. Effects of fracturing fluid recovery upon well performance and ultimate recovery of hydraulically fractured gas wells 

    E-Print Network [OSTI]

    Berthelot, Jan Marie

    1990-01-01

    EFFECTS OF FRACTURING FLUID RECOVERY UPON WELL PERFORMANCE AND ULTIMATE RECOVERY OF HYDRAULICALLY FRACTURED GAS WELLS A Thesis IAN MARIE BERTHELOT Submitted to the Office of Graduate Studies of Texas AdtM University in partial fulfillment... of the requirements for the degree of MASTER OF SCIENCE May 1990 Major Subject: Petroleum Engineering EFFECTS OF FRACTURING FLUID RECOVERY UPON WELL PERFORMANCE AND ULTIMATE RECOVERY OF HYDRAULICALLY FRACTURED GAS WELLS by JAN MARIE BERTIIELOT Appmved...

  18. Completion practices in deep sour Tuscaloosa wells

    SciTech Connect (OSTI)

    Huntoon, G.G.

    1984-01-01

    Successful development of the Tuscaloosa trend in Louisiana has required unique completion practices to produce the trend's deep sour formations. Amoco's operations in the Tuscaloosa formation are between 16,000 and 21,000 ft (4877 and 6400 m), and a range of pressure environments, high temperatures, and corrosive elements is encountered. Application of proved completion practices and equipment has resulted in several techniques that enhance the safety, longevity, and production capacity of these wells. The design of deep Tuscaloosa completions is assisted by a series of correlations developed to project bottomhole and surface shut-in tubing pressures, temperature gradients, and flow capacities for deep sour wells. This paper discusses material selection, completion practices, completion fluids, wellhead equipment, packer designs, corrosion-inhibition systems, and safety and monitoring equipment used in the Tuscaloosa trend. The design of a wellhead surface installation used to detect equipment failure, to pump kill fluids, and to circulate corrosion inhibitors is reviewed. A case study illustrates the methods used in completing a Tuscaloosa well with surface pressures exceeding 16,000 psi (110.3 MPa). Deep high-pressure sour-gas wells can be completed safely if all the elements of the environment that will affect the mechanical integrity of the wellbore are considered in the completion designs. The development of higher-strength material capable of withstanding SSC is needed if wells are completed in formations deeper than 22,000 ft (6700 m). Further research is necessary on the use of alloy steels and nonferrous metals for sour service. Effective high-temperature corrosion inhibitors for heavy zinc bromide completion fluids must be developed before these brines can be used in the Tuscaloosa. The testing of new inhibitors for use in highpressure sour-gas completions should be continued.

  19. Completion report for Well Cluster ER-20-6

    SciTech Connect (OSTI)

    1998-02-01

    The Well Cluster ER-20-6 drilling and completion project was conducted during February, March, and April of 1996 in support of the Nevada Environmental Restoration Project at the Nevada Test Site (NTS), Nye County, Nevada. This project is part of the DOE`s Underground Test Area (UGTA) subproject at the NTS. The primary UGTA tasks include collecting geological, geophysical, and hydrological data from new and existing wells to define groundwater quality as well as pathways and rates of groundwater migration at the NTS. A program of drilling wells near the sites of selected underground nuclear tests (near-field drilling) was implemented as part of the UGTA subproject to obtain site-specific data on the nature and extent of migration of radionuclides produced by an underground nuclear explosion. The ER-20-6 near-field drilling project was originally planned to be very similar to that recently conducted at Well Cluster ER-20-5, which was designed to obtain data on the existing hydrologic regime near the site of an underground nuclear explosion (IT, 1995; IT, 1996a). However, after further consideration of the goals of the near-field drilling program and the characteristics of the BULLION site, the TWG recommended that the ER-20-6 project be redesigned to accommodate a forced-gradient experiment. This proposed experiment is expected to yield more realistic estimates of transport parameters than can be deduced from sampling and testing natural groundwater flow systems.

  20. Completion Report for Well ER-2-1

    SciTech Connect (OSTI)

    Bechtel Nevada

    2004-10-01

    Well ER-2-1 was drilled for the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office (formerly Nevada Operations Office), in support of the Nevada Environmental Restoration Project at the Nevada Test Site, Nye County, Nevada. This well was drilled in February and March of 2003, as part of a hydrogeologic investigation program for the Yucca Flat/Climax Mine Corrective Action Unit in the northeastern portion of the Nevada Test Site. Well ER-2-1 was drilled as part of the Yucca Flat Corrective Action Unit Phase I drilling initiative. The well is located in north central Yucca Flat within Area 2 of the Nevada Test Site, and provided information regarding the radiological and physical environment near underground nuclear tests conducted in a saturated volcanic aquifer setting. Detailed lithologic descriptions with stratigraphic assignments are included in this report. These are based on composite drill cuttings collected every 3 meters and 83 sidewall samples taken at various depths between 113.7 and 754.4 meters, supplemented by geophysical log data. Detailed petrographic, chemical, and mineralogical studies of rock samples were conducted on 27 samples of drill cuttings. The well was collared in tuffaceous alluvium, and penetrated Tertiary-age tuffs of the Timber Mountain and Paintbrush Groups, Calico Hills and Wahmonie Formations, Crater Flat Group, Grouse Canyon Formation, before reaching total depth in the Tunnel Bed Formation.

  1. Completion Report for Well Cluster ER-5-4

    SciTech Connect (OSTI)

    U.S. Department of Energy, National Nuclear Security Administration, Nevada Site Office; Bechtel Nevada

    2005-02-01

    Well Cluster ER-5-4 was drilled for the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office, in support of the Nevada Environmental Restoration Project at the Nevada Test Site, Nye County, Nevada. The cluster consists of two wells, positioned about 30 meters apart on the same drill pad, constructed as part of a hydrogeologic investigation program for Frenchman Flat at the Nevada Test Site. Detailed lithologic descriptions with preliminary stratigraphic assignments for the well cluster are included in this report. These are based on composite drill cuttings collected every 3 meters, and 156 sidewall samples taken at various depths below 192 meters in both boreholes, supplemented by geophysical log data. Detailed petrographic, chemical, and mineralogical studies of rock samples were conducted on 122 samples. Well ER-5-4 penetrated approximately 1,120 meters of Quaternary and Tertiary alluvium before reaching total depth in Tertiary volcanic rocks at 1,137.5 meters. The deeper Well ER-5-4 No.2 penetrated 1,120.4 meters of alluvial sediments, and was terminated within Tertiary volcanic rocks at a depth of 2,133.6 meters, indicating that Paleozoic rocks are deeper than expected at this site.

  2. Newberry Well 55-29 Stimulation Data 2014

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Trenton T. Cladouhos

    2015-09-03

    The Newberry Volcano EGS Demonstration in central Oregon, a 5 year project begun in 2010, tests recent technological advances designed to reduce the cost of power generated by EGS in a hot, dry well (NWG 55-29) drilled in 2008. First, the stimulation pumps used were designed to run for weeks and deliver large volumes of water at moderate well-head pressure. Second, to stimulate multiple zones, AltaRock developed thermo-degradable zonal isolation materials (TZIMs) to seal off fractures in a geothermal well to stimulate secondary and tertiary fracture zones. The TZIMs degrade within weeks, resulting in an optimized injection/ production profile of the entire well. Third, the project followed a project-specific Induced Seismicity Mitigation Plan (ISMP) to evaluate, monitor for, and mitigate felt induced seismicity. An initial stimulation was conducted in 2012 and continued for 7 weeks, with over 41,000 m3 of water injected. Further analysis indicated a shallow casing leak and an unstable formation in the open hole. The well was repaired with a shallow casing tieback and perforated liner in the open hole and re-stimulated in 2014. The second stimulation started September 23rd, 2014 and continued for 3 weeks with over 9,500 m3 of water injected. The well was treated with several batches of newly tested TZIM diverter materials and a newly designed Diverter Injection Vessel Assembly (DIVA), which was the main modification to the original injection system design used in 2012. A second round of stimulation that included two perforation shots and additional batches of TZIM was conducted on November 11th, 2014 for 9 days with an additional 4,000 m3 of water injected. The stimulations resulted in a 3-4 fold increase in injectivity, and PTS data indicates partial blocking and creation of flow zones near the bottom of the well.

  3. Newberry Well 55-29 Stimulation Data 2014

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Trenton T. Cladouhos

    The Newberry Volcano EGS Demonstration in central Oregon, a 5 year project begun in 2010, tests recent technological advances designed to reduce the cost of power generated by EGS in a hot, dry well (NWG 55-29) drilled in 2008. First, the stimulation pumps used were designed to run for weeks and deliver large volumes of water at moderate well-head pressure. Second, to stimulate multiple zones, AltaRock developed thermo-degradable zonal isolation materials (TZIMs) to seal off fractures in a geothermal well to stimulate secondary and tertiary fracture zones. The TZIMs degrade within weeks, resulting in an optimized injection/ production profile of the entire well. Third, the project followed a project-specific Induced Seismicity Mitigation Plan (ISMP) to evaluate, monitor for, and mitigate felt induced seismicity. An initial stimulation was conducted in 2012 and continued for 7 weeks, with over 41,000 m3 of water injected. Further analysis indicated a shallow casing leak and an unstable formation in the open hole. The well was repaired with a shallow casing tieback and perforated liner in the open hole and re-stimulated in 2014. The second stimulation started September 23rd, 2014 and continued for 3 weeks with over 9,500 m3 of water injected. The well was treated with several batches of newly tested TZIM diverter materials and a newly designed Diverter Injection Vessel Assembly (DIVA), which was the main modification to the original injection system design used in 2012. A second round of stimulation that included two perforation shots and additional batches of TZIM was conducted on November 11th, 2014 for 9 days with an additional 4,000 m3 of water injected. The stimulations resulted in a 3-4 fold increase in injectivity, and PTS data indicates partial blocking and creation of flow zones near the bottom of the well.

  4. GAS INJECTION/WELL STIMULATION PROJECT

    SciTech Connect (OSTI)

    John K. Godwin

    2005-12-01

    Driver Production proposes to conduct a gas repressurization/well stimulation project on a six well, 80-acre portion of the Dutcher Sand of the East Edna Field, Okmulgee County, Oklahoma. The site has been location of previous successful flue gas injection demonstration but due to changing economic and sales conditions, finds new opportunities to use associated natural gas that is currently being vented to the atmosphere to repressurize the reservoir to produce additional oil. The established infrastructure and known geological conditions should allow quick startup and much lower operating costs than flue gas. Lessons learned from the previous project, the lessons learned form cyclical oil prices and from other operators in the area will be applied. Technology transfer of the lessons learned from both projects could be applied by other small independent operators.

  5. On the global economic potentials and marginal costs of non-renewable resources and the price dynamics of energy commodities

    E-Print Network [OSTI]

    Mercure, Jean-Francois

    2013-01-01

    A model is presented in this work for simulating endogenously the evolution of the marginal costs of production of energy carriers from non-renewable resources, their consumption, depletion pathways and timescales. Such marginal costs can be used to simulate the long term average price formation of energy commodities. Drawing on previous work where a global database of energy resource economic potentials was constructed, this work uses cost distributions of non-renewable resources in order to evaluate global flows of energy commodities. A mathematical framework is given to calculate endogenous flows of energy resources given an exogenous commodity price path. This framework can be used in reverse in order to calculate an exogenous marginal cost of production of energy carriers given an exogenous carrier demand. Using rigid price inelastic assumptions independent of the economy, these two approaches generate limiting scenarios that depict extreme use of natural resources. This is useful to characterise the cur...

  6. Marginal cost of natural gas in developing countries: concepts and applications

    SciTech Connect (OSTI)

    Mashayekhi, A.

    1983-01-01

    Many developing nations are facing complex questions regarding the best strategy for developing their domestic gas reserves. The World Bank has addressed these questions in studies on the cost and prices of gas and its optimal allocation among different markets. Based on the average incremental method, an estimate of the marginal cost of natural gas in 10 developing countries proved to be $0.61-1.79/1000 CF or $3.59-10.54/bbl of oil equivalent, far below the border prices of competing fuels in these nations. Moreover, the cost of gas is not expected to rise in these countries within the next 20 years while the reserves/production ratios remain high. The sample involves a variety of gas compositions and production conditions among the countries of Bangladesh, Cameroon, Egypt, India, Morocco, Nigeria, Pakistan, Tanzania, Thailand, and Tunisia.

  7. Ideas underlying quantification of margins and uncertainties(QMU): a white paper.

    SciTech Connect (OSTI)

    Helton, Jon Craig; Trucano, Timothy Guy; Pilch, Martin M.

    2006-09-01

    This report describes key ideas underlying the application of Quantification of Margins and Uncertainties (QMU) to nuclear weapons stockpile lifecycle decisions at Sandia National Laboratories. While QMU is a broad process and methodology for generating critical technical information to be used in stockpile management, this paper emphasizes one component, which is information produced by computational modeling and simulation. In particular, we discuss the key principles of developing QMU information in the form of Best Estimate Plus Uncertainty, the need to separate aleatory and epistemic uncertainty in QMU, and the risk-informed decision making that is best suited for decisive application of QMU. The paper is written at a high level, but provides a systematic bibliography of useful papers for the interested reader to deepen their understanding of these ideas.

  8. MNSR transient analyses and thermal-hydraulic safety margins for HEU and LEU cores using PARET

    SciTech Connect (OSTI)

    Olson, Arne P. [RERTR Program, Argonne National Laboratory, Argonne, IL 60439 (United States); Jonah, S.A. [Centre for Energy Research and Training, Ahmadu Bello University, Zaria, P.M.B. 1014 (Nigeria)

    2008-07-15

    Thermal-hydraulic performance characteristics of Miniature Neutron Source Reactors under long-term steady-state and transient conditions are investigated. Safety margins and limiting conditions attained during these events are determined. Modeling extensions are presented that enable the PARET/ANL code to realistically track primary loop heatup, heat exchange to the pool, and heat loss from the pool to air over the pool. Comparisons are made of temperature predictions for HEU and LEU fueled cores under transient conditions. Results are obtained using three different natural convection heat transfer correlations: the original (PARET/ANL version 5), Churchill-Chu, and an experiment- based correlation from the China Institute of Atomic Energy (CIAE). The MNSR, either fueled by HEU or by LEU, satisfies the design limits for long-term transient operation. (author)

  9. Marginal instability threshold condition of the aperiodic ordinary mode in equal-mass plasmas

    SciTech Connect (OSTI)

    Vafin, S.; Schlickeiser, R.; Yoon, P. H.

    2014-10-15

    The purely growing ordinary (O) mode instability for counter-streaming bi-Maxwellian plasma particle distribution functions has recently received renewed attention due to its importance for the solar wind plasma. Here, the analytical marginal instability condition is derived for magnetized plasmas consisting of equal-mass charged particles, distributed in counter-streams with equal temperatures. The equal-mass composition assumption enormously facilitates the theoretical analysis due to the equality of the values of the electron and positron (positive and negative ion) plasma and gyrofrequencies. The existence of a new instability domain of the O-mode at small plasma beta values is confirmed, when the parallel counter-stream free energy exceeds the perpendicular bi-Maxwellian free energy.

  10. Vibration of Generalized Double Well Oscillators

    E-Print Network [OSTI]

    Grzegorz Litak; Marek Borowiec; Arkadiusz Syta

    2006-10-20

    We have applied the Melnikov criterion to examine a global homoclinic bifurcation and transition to chaos in a case of a double well dynamical system with a nonlinear fractional damping term and external excitation. The usual double well Duffing potential having a negative square term and positive quartic term has been generalized to a double well potential with a negative square term and a positive one with an arbitrary real exponent $q > 2$. We have also used a fractional damping term with an arbitrary power $p$ applied to velocity which enables one to cover a wide range of realistic damping factors: from dry friction $p \\to 0$ to turbulent resistance phenomena $p=2$. Using perturbation methods we have found a critical forcing amplitude $\\mu_c$ above which the system may behave chaotically. Our results show that the vibrating system is less stable in transition to chaos for smaller $p$ satisfying an exponential scaling low. The critical amplitude $\\mu_c$ as an exponential function of $p$. The analytical results have been illustrated by numerical simulations using standard nonlinear tools such as Poincare maps and the maximal Lyapunov exponent. As usual for chosen system parameters we have identified a chaotic motion above the critical Melnikov amplitude $\\mu_c$.

  11. Coiled tubing workover saves horizontal well in Lake Maracaibo

    SciTech Connect (OSTI)

    Lizak, K.; Patterson, J.; Suarez, D.; Salas, J.

    1996-12-31

    A slotted liner horizontal completion became stuck while being run. Inflatable packers were to be used to isolate the productive interval from a water-bearing, unconsolidated sand in the curved section of this well. While personnel were deciding how to cement the well, the liner was left in the hole with the inflatable packers unset, and the production tubing was run. Coiled tubing was used to log the well, isolate the productive interval, and remove damage to restore well productivity. Personnel considered all possible options, and a thorough decision-making process guided the workover. Because of severe lost-circulation problems, extensive ``what if`` scenarios were made and updated daily for the engineers on location. Service company and oil company personnel worked together to guarantee the job designs were practical and did not exceed the limits of the equipment on location. Computer simulations of all operations were run to allow corrective action to be taken if unusual circumstances arose. All fluids were thoroughly laboratory tested and witnessed by oil company personnel to ensure job success. Problems on the job included lost circulation, locating the exact positions of the packers and water zone, ensuring correct cement placement, removing mud and workover fluids without damaging the squeeze, and bad weather on Lake Maracaibo. Advantages and disadvantages of all the solutions that were considered are included to assist anyone in a similar situation. Post-job oil production has stabilized at 900 BOPD with no water or sand production. Careful job planning and the versatility of coiled tubing saved this well and proved economical with an estimated payout of 33 days, assuming a price of $12 per barrel of oil.

  12. Generic effluent monitoring system certification for salt well portable exhauster

    SciTech Connect (OSTI)

    Glissmeyer, J.A.; Maughan, A.D.

    1997-09-01

    Tests were conducted to verify that the Generic Effluent Monitoring System (GEMS), as it is applied to the Salt Well Portable Exhauster, meets all applicable regulatory performance criteria for air sampling systems at nuclear facilities. These performance criteria address both the suitability of the air sampling probe location and the transport of the sample to the collection devices. The criteria covering air sampling probe location ensure that the contaminants in the stack are well mixed with the airflow at the probe location such that the extracted sample represents the whole. The sample transport criteria ensure that the sampled contaminants are quantitatively delivered to the collection device. The specific performance criteria are described in detail in the report. The tests demonstrated that the GEMS/Salt Well Exhauster system meets all applicable performance criteria. Pacific Northwest National Laboratory conducted the testing using a mockup of the Salt Well Portable Exhauster stack at the Numatec Hanford Company`s 305 Building. The stack/sampling system configuration tested was designed to provide airborne effluent control for the Salt Well pumping operation at some U.S. Department of Energy (DOE) radioactive waste storage tanks at the Hanford Site, Washington. The portable design of the exhauster allows it to be used in other applications and over a range of exhaust air flowrates (approximately 200 - 1100 cubic feet per minute). The unit includes a stack section containing the sampling probe and another stack section containing the airflow, temperature and humidity sensors. The GEMS design features a probe with a single shrouded sampling nozzle, a sample delivery line, and sample collection system. The collection system includes a filter holder to collect the sample of record and an in-line detector head and filter for monitoring beta radiation-emitting particles.

  13. SU-E-T-36: An Investigation of the Margin From CTV to PTV Using Retraction Method for Cervical Carcinoma

    SciTech Connect (OSTI)

    Wu, D; Chen, J; Hao, Y; Liao, C; Huang, Y; Mo, Y; Wei, Y [The People's Hospital of Guangxi Zhuang Autonomous Region, Nanning, Guangxi (China)

    2014-06-01

    Purpose: This work employs the retraction method to compute and evaluate the margin from CTV to PTV based on the influence of target dosimetry of setup errors during cervical carcinoma patients treatment. Methods: Sixteen patients with cervical cancer were treated by Elekta synergy and received a total of 305 KV-CBCT images. The iso-center of the initial plans were changed according to the setup errors to simulate radiotherapy and then recalculated the dose distribution using leaf sequences and MUs for individual plans. The margin from CTV to PTV will be concluded both by the method of retracting (Fixed the PTV of the original plan, and retract PTV a certain distance defined as simulative organization CTVnx. The minimum distance value from PTV to CTVnx which get specified doses, namely guarantee at least 99% CTV volume can receive the dose of 95%, is the margin CTV to PTV we found) and the former formula method. Results: (1)The setup errors of 16 patients in X, Y and Z directions were(1.13±2.94) mm,(?1.63±7.13) mm,(?0.65±2.25) mm. (2) The distance between CTVx and PTV was 5, 9 and 3mm in X, Y and Z directions According to 2.5+0.7?. (3) Transplantation plans displayed 99% of CTVx10- CTVx7 and received 95% of prescription dose, but CTVx6- CTVx3 departed from standard of clinic.In order to protect normal tissues, we selected 7mm as the minimum value of the margin from CTV to PTV. Conclusion: We have test an retraction method for the margin from CTV to PTV evaluation. The retraction method is more reliable than the formula method for calculating the margin from the CTV to the PTV, because it represented practice of treatment, and increasing a new method in this field.

  14. Stereotactic Radiosurgery of the Postoperative Resection Cavity for Brain Metastases: Prospective Evaluation of Target Margin on Tumor Control

    SciTech Connect (OSTI)

    Choi, Clara Y.H.; Chang, Steven D.; Gibbs, Iris C.; Adler, John R.; Harsh, Griffith R.; Lieberson, Robert E.; Soltys, Scott G.

    2012-10-01

    Purpose: Given the neurocognitive toxicity associated with whole-brain irradiation (WBRT), approaches to defer or avoid WBRT after surgical resection of brain metastases are desirable. Our initial experience with stereotactic radiosurgery (SRS) targeting the resection cavity showed promising results. We examined the outcomes of postoperative resection cavity SRS to determine the effect of adding a 2-mm margin around the resection cavity on local failure (LF) and toxicity. Patients and Methods: We retrospectively evaluated 120 cavities in 112 patients treated from 1998-2009. Factors associated with LF and distant brain failure (DF) were analyzed using competing risks analysis, with death as a competing risk. The overall survival (OS) rate was calculated by the Kaplan-Meier product-limit method; variables associated with OS were evaluated using the Cox proportional hazards and log rank tests. Results: The 12-month cumulative incidence rates of LF and DF, with death as a competing risk, were 9.5% and 54%, respectively. On univariate analysis, expansion of the cavity with a 2-mm margin was associated with decreased LF; the 12-month cumulative incidence rates of LF with and without margin were 3% and 16%, respectively (P=.042). The 12-month toxicity rates with and without margin were 3% and 8%, respectively (P=.27). On multivariate analysis, melanoma histology (P=.038) and number of brain metastases (P=.0097) were associated with higher DF. The median OS time was 17 months (range, 2-114 months), with a 12-month OS rate of 62%. Overall, WBRT was avoided in 72% of the patients. Conclusion: Adjuvant SRS targeting the resection cavity of brain metastases results in excellent local control and allows WBRT to be avoided in a majority of patients. A 2-mm margin around the resection cavity improved local control without increasing toxicity compared with our prior technique with no margin.

  15. Nanoparticle-induced light scattering for improved performance of quantum-well solar cells

    E-Print Network [OSTI]

    Yu, Edward T.

    in the application of semiconductor nanostructures, including quantum-well structures,1 nanowires,2 and quantum dots3Nanoparticle-induced light scattering for improved performance of quantum-well solar cells D performance of InP/InGaAsP quantum-well waveguide solar cells via light scattering from deposited dielectric

  16. Productivity and injectivity of horizontal wells. Quarterly report...

    Office of Scientific and Technical Information (OSTI)

    99 MATHEMATICS, COMPUTERS, INFORMATION SCIENCE, MANAGEMENT, LAW, MISCELLANEOUS; OIL WELLS; DAMAGE; WELL DRILLING; WELL COMPLETION; EQUATIONS; PROGRESS REPORT This report...

  17. The effects of a marginal intake of magnesium with soy protein concentrate on growth, gestation, and lactation in the rat 

    E-Print Network [OSTI]

    McLaughlin, Cynthia Anne

    1986-01-01

    THE EFFECTS OF A MARGINAL INTAKE OF MAGNESIUM WITH SOY PROTEIN CONCENTRATE ON GROWTH, GESTATION, AND LACTATION IN THE RAT A Thesis by CYNTHIA ANNE MCLAUGHLIN Submitted to the Graduate College of Texas A&M University in partial fulfillment... of the requirements for the degree of MASTER OF SCIENCE May 19B6 Major Subject: Nutrrtion THE EFFECTS OF A MARGINAL INTAKE OF MAGNESIUM WITH SOY PROTEIN CONCENTRATE ON GROWTH, GESTATION, AND LACTATION IN THE RAT A Thesis by CYNTHIA ANNE MCLAUGHLIN Approved...

  18. Increasing Well Productivity in Gas Condensate Wells in Qatar's North Field 

    E-Print Network [OSTI]

    Miller, Nathan

    2010-07-14

    2.1.4. Method for Reduction of Non Darcy Flow Study ......... 17 2.2. PVT Analysis .......................................................................... 17 2.3. Reservoir Description... to study Non Darcy flow in both a multilateral well and a vertical well. A Non Darcy flow sensitivity test is run to see the impact Non Darcy flow has on near wellbore condensate blockage, and therefore, gas well productivity. 2.2. PVT...

  19. Hydraulic fracture stimulation treatment of Well Baca 23. Geothermal Reservoir Well-Stimulation Program

    SciTech Connect (OSTI)

    Not Available

    1981-06-01

    Well Stimulation Experiment No. 5 of the Geothermal Reservoir Well Stimulation Program (GRWSP) was performed on March 22, 1981 in Baca 23, located in Union's Redondo Creek Project Area in Sandoval County, New Mexico. The treatment selected was a large hydraulic fracture job designed specifically for, and utilizing frac materials chosen for, the high temperature geothermal environment. The well selection, fracture treatment, experiment evaluation, and summary of the job costs are presented herein.

  20. Wells, Vermont: Energy Resources | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page| Open Energy Information Serbia-EnhancingEtGeorgia: Energy Resources Jump to:Search YourIndiana: EnergyWells, Vermont:

  1. Infinite potential well with a sinusoidal bottom

    E-Print Network [OSTI]

    A. D. Alhaidari; H. Bahlouli

    2008-08-07

    We construct a tridiagonal matrix representation of the wave operator that maps the wave equation into a three-term recursion relation for the expansion coefficients of the wavefunction. Finding a solution of the recursion relation is equivalent to solving the original problem. Consequently, a larger class of solvable potentials is obtained. The usual diagonal representation constraint results in a reduction to the conventional class of solvable potentials. To exhibit the power of this approach, we give an exact solution for the infinite potential well with sinusoidal bottom.

  2. In situ bioremediation using horizontal wells

    SciTech Connect (OSTI)

    NONE

    1995-04-01

    In Situ Bioremediation (ISB), which is the term used in this report for Gaseous Nutrient Injection for In Situ Bioremediation, remediates soils and ground water contaminated with volatile organic compounds (VOCs) both above and below the water table. ISB involves injection of air and nutrients (sparging and biostimulation) into the ground water and vacuum extraction to remove .VOCs from the vadose zone concomitant with biodegradation of VOCs. The innovation is in the combination of 3 emerging technologies, air stripping, horizontal wells, and bioremediation via gaseous nutrient injection with a baseline technology, soil vapor extraction, to produce a more efficient in situ remediation system.

  3. Logging of subterranean wells using coiled tubing

    SciTech Connect (OSTI)

    Pilla, J.

    1991-01-15

    This patent describes an apparatus for production logging of a well utilizing artificial lift in a wellbore. It comprises: coiled tubing extending into the wellbore having wireline electrical cable passing through a central bore thereof and having a remote end within the wellbore which end is connected to gas injector means. The wireline cable passing through the gas injector means to a flexible electrically conductive support spacer having an end portion remote from the gas injector means and logging means connected to the end portion of the support spacer.

  4. Production Well Performance Enhancement using Sonication Technology

    SciTech Connect (OSTI)

    Adewumi, Michael A; Ityokumbul, M Thaddeus; Watson, Robert W; Eltohami, Eltohami; Farias, Mario; Heckman, Glenn; Houlihan, Brendan; Karoor, Samata Prakash; Miller, Bruce G; Mohammed, Nazia; Olanrewaju, Johnson; Ozdemir, Mine; Rejepov, Dautmamed; Sadegh, Abdallah A; Quammie, Kevin E; Zaghloul, Jose; Hughes, W Jack; Montgomery, Thomas C

    2005-12-31

    The objective of this project was to develop a sonic well performance enhancement technology that focused on near wellbore formation damage. In order to successfully achieve this objective, a three-year project was defined. The entire project was broken into four tasks. The overall objective of all this was to foster a better understanding of the mechanisms involved in sonic energy interactions with fluid flow in porous media and adapt such knowledge for field applications. The fours tasks are: • Laboratory studies • Mathematical modeling • Sonic tool design and development • Field demonstration The project was designed to be completed in three years; however, due to budget cuts, support was only provided for the first year, and hence the full objective of the project could not be accomplished. This report summarizes what was accomplished with the support provided by the US Department of Energy. Experiments performed focused on determining the inception of cavitation, studying thermal dissipation under cavitation conditions, investigating sonic energy interactions with glass beads and oil, and studying the effects of sonication on crude oil properties. Our findings show that the voltage threshold for onset of cavitation is independent of transducer-hydrophone separation distance. In addition, thermal dissipation under cavitation conditions contributed to the mobilization of deposited paraffins and waxes. Our preliminary laboratory experiments suggest that waxes are mobilized when the fluid temperature approaches 40°C. Experiments were conducted that provided insights into the interactions between sonic wave and the fluid contained in the porous media. Most of these studies were carried out in a slim-tube apparatus. A numerical model was developed for simulating the effect of sonication in the nearwellbore region. The numerical model developed was validated using a number of standard testbed problems. However, actual application of the model for scale-up purposes was limited due to funding constraints. The overall plan for this task was to perlorm field trials with the sonication tooL These trials were to be performed in production and/or injection wells located in Pennsylvania, New York, and West Virginia. Four new wells were drilled in preparation for the field demonstration. Baseline production data were collected and reservoir simulator tuned to simulate these oil reservoirs. The sonication tools were designed for these wells. However, actual field testing could not be carried out because of premature termination of the project.

  5. Decline curve analysis for horizontal wells 

    E-Print Network [OSTI]

    Shih, Min-Yu

    1994-01-01

    Subject; Petroleum Engineering DECLINE CURVE ANALYSIS FOR HORIZONTAL WELLS A Thesis by MIN- YU SHIH Submitted to Texas A8tM University in partial fulfillment of the requirements for the degtee of MASTER OF SCIENCE Approved as to style and content... curves are given as log-log plots of MttdaLLattaad: Fetkovich Type Curve Radial Flow, Circular Reservoir Solutions 12 Transient "Stems" tTransient Flow) 8 001 160 000 x10 Depletion "Stems" (Boundary-Dominated Flow) r)04Arps Equations b 0 0...

  6. Spontaneous Potential Well Log | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page| Open Energy Information Serbia-Enhancing CapacityVectren) Jump to:Spill Prevention andWell Log Jump to: navigation,

  7. California Water Well Standards | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmentalBowerbank, Maine:Kansas: EnergyCalendarCalhounWebpageProjectPrograms Jump to:Well

  8. Category:Production Wells | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmentalBowerbank,CammackFLIR Jump to: navigation,GroundNearGeothermalpower.jpgWells Jump to:

  9. Category:Well Deepening | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on QA:QA J-E-1 SECTION JEnvironmentalBowerbank,CammackFLIR Jump to:RAPID RoadmapInformation Utility RateWaterWell

  10. Completion Report for Well ER-12-2

    SciTech Connect (OSTI)

    Bechtel Nevada

    2004-11-01

    Well ER-12-2 was drilled for the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office, in support of the Nevada Environmental Restoration Project at the Nevada Test Site, Nye County, Nevada. The well was drilled from November 2002 to January 2003 as part of a hydrogeologic investigation program for the Yucca Flat Corrective Action Unit. The overall purpose of the well was to gather subsurface data to better characterize the hydrogeology in the northwestern portion of Yucca Flat. The well was drilled to total measured depth of 2,097.9 meters. The 131.1-centimeter-diameter borehole was left open (i.e., uncased) below the base of the intermediate casing at 901.6 meters. A piezometer string was installed outside the surface casing to a depth of 176.4 meters to monitor a zone of perched water. Data gathered during and shortly after hole construction include composite drill cuttings samples collected every 3 meters, sidewall core samples from 7 depths, various geophysical logs, and water level measurements. These data indicate that the well penetrated, in descending order, 137.5 meters of Quaternary and Tertiary alluvium, 48.8 meters of Tertiary volcanic rocks, 289.6 meters of Mississippian Chainman Shale, and 1,622.5 meters of Mississippian and Upper Devonian Eleana Formation consisting of shale, argillite, sandstone, quartzite, and limestone. Forty-seven days after the well was drilled the water level inside the main hole was tagged at the depth of 65.43 meters, and the water level inside the piezometer string was tagged at 127.14 meters.

  11. Completion Report for Well ER-EC-1

    SciTech Connect (OSTI)

    Townsend, M.J.

    2000-12-01

    Well ER-EC-1 was drilled for the U.S. Department of Energy, Nevada Operations Office in support of the Nevada Environmental Restoration Project at the Nevada Test Site, Nye County, Nevada. This well was drilled in the spring of 1999 as part of the U.S. Department of Energy's hydrogeologic investigation well program in the Western Pahute Mesa - Oasis Valley region just west of the Test Site. A 44.5-centimeter surface hole was drilled and cased off to the depth 675.1 meters below the surface. The hole diameter was then decreased to 31.1 centimeters for drilling to a total depth of 1,524.0 meters. A preliminary composite, static, water level was measured at the depth of approximately 566.3 meters prior to installation of the completion string. One completion string with three isolated, slotted intervals was installed in the well. Detailed lithologic descriptions with preliminary stratigraphic assignments are included in the report. These are based on composite drill cuttings collected every 3 meters and 31 sidewall samples taken at various depths below 680 meters, supplemented by geophysical log data. Detailed chemical and mineralogical studies of rock samples are in progress. The well penetrated Tertiary-age lava and tuff of the Timber Mountain Group, the Paintbrush Group, the Calico Hills Formation, the Crater Flat Group, and the Volcanics of Quartz Mountain. The preliminary geologic interpretation of data from Well ER-EC-1 indicates the presence of a structural trough or bench filled with a thick section of post-Rainier Mesa lava. These data also suggest that this site is located on a buried structural ridge that may separate the Silent Canyon and Timber Mountain caldera complexes.

  12. Title IX & Discrimination Complaint Form (including sexual harassment)

    E-Print Network [OSTI]

    Walker, Lawrence R.

    Title IX & Discrimination Complaint Form (including sexual harassment) Office of Diversity. Although the university cannot commit to keeping a complaint of discrimination confidential the process for filing or investigating complaints of discrimination (including sexual harassment). Note

  13. Explosion at Louisa (including Morrison Old) Colliery, Durham 

    E-Print Network [OSTI]

    Yates, R.

    MINISTRY OF FUEL AND POWER - EXPLOSION AT LOUISA (including MORRISON OLD) COLLIERY, DURHAM REPORT On the Causes of, and Circumstances attending, the Explosion which occurred at Louisa (including Morrison Old) Colliery, ...

  14. Fluid-Rock Characterization and Interactions in NMR Well Logging

    SciTech Connect (OSTI)

    George J. Hirasaki; Kishore K. Mohanty

    2005-09-05

    The objective of this report is to characterize the fluid properties and fluid-rock interactions that are needed for formation evaluation by NMR well logging. The advances made in the understanding of NMR fluid properties are summarized in a chapter written for an AAPG book on NMR well logging. This includes live oils, viscous oils, natural gas mixtures, and the relation between relaxation time and diffusivity. Oil based drilling fluids can have an adverse effect on NMR well logging if it alters the wettability of the formation. The effect of various surfactants on wettability and surface relaxivity are evaluated for silica sand. The relation between the relaxation time and diffusivity distinguishes the response of brine, oil, and gas in a NMR well log. A new NMR pulse sequence in the presence of a field gradient and a new inversion technique enables the T{sub 2} and diffusivity distributions to be displayed as a two-dimensional map. The objectives of pore morphology and rock characterization are to identify vug connectivity by using X-ray CT scan, and to improve NMR permeability correlation. Improved estimation of permeability from NMR response is possible by using estimated tortuosity as a parameter to interpolate between two existing permeability models.

  15. Apparatus and method for sealing perforated well casing

    DOE Patents [OSTI]

    Blount, C.G.; Benham, R.A.; Brock, J.L.; Emerson, J.A.; Ferguson, K.R.; Scheve, D.F.; Schmidt, J.H.; Schuler, K.W.; Stanton, P.L.

    1997-03-25

    Perforations and other openings in well casings, liners and other conduits may be substantially blocked or sealed to prevent fluid flow between the casing or liner interior and an earth formation by placing a radially expansible sleeve adjacent the perforations or openings and urging the sleeve into forcible engagement with the casing or inner wall using an explosive charge. An apparatus including a radially contracted sleeve formed by a coiled plate member or a tubular member having flutes defined by external and internal folds, may be deployed into a well casing or liner through a production or injection tubing string and on the end of a flexible cable or coilable tubing. An explosive charge disposed on the apparatus and within the sleeve may be detonated to urge the sleeve into forcible engagement with the casing inner wall. 17 figs.

  16. Spatially indirect excitons in coupled quantum wells

    SciTech Connect (OSTI)

    Lai, Chih-Wei Eddy

    2004-03-01

    Microscopic quantum phenomena such as interference or phase coherence between different quantum states are rarely manifest in macroscopic systems due to a lack of significant correlation between different states. An exciton system is one candidate for observation of possible quantum collective effects. In the dilute limit, excitons in semiconductors behave as bosons and are expected to undergo Bose-Einstein condensation (BEC) at a temperature several orders of magnitude higher than for atomic BEC because of their light mass. Furthermore, well-developed modern semiconductor technologies offer flexible manipulations of an exciton system. Realization of BEC in solid-state systems can thus provide new opportunities for macroscopic quantum coherence research. In semiconductor coupled quantum wells (CQW) under across-well static electric field, excitons exist as separately confined electron-hole pairs. These spatially indirect excitons exhibit a radiative recombination time much longer than their thermal relaxation time a unique feature in direct band gap semiconductor based structures. Their mutual repulsive dipole interaction further stabilizes the exciton system at low temperature and screens in-plane disorder more effectively. All these features make indirect excitons in CQW a promising system to search for quantum collective effects. Properties of indirect excitons in CQW have been analyzed and investigated extensively. The experimental results based on time-integrated or time-resolved spatially-resolved photoluminescence (PL) spectroscopy and imaging are reported in two categories. (i) Generic indirect exciton systems: general properties of indirect excitons such as the dependence of exciton energy and lifetime on electric fields and densities were examined. (ii) Quasi-two-dimensional confined exciton systems: highly statistically degenerate exciton systems containing more than tens of thousands of excitons within areas as small as (10 micrometer){sup 2} were observed. The spatial and energy distributions of optically active excitons were used as thermodynamic quantities to construct a phase diagram of the exciton system, demonstrating the existence of distinct phases. Optical and electrical properties of the CQW sample were examined thoroughly to provide deeper understanding of the formation mechanisms of these cold exciton systems. These insights offer new strategies for producing cold exciton systems, which may lead to opportunities for the realization of BEC in solid-state systems.

  17. Comparison of Joint Modeling Approaches Including Eulerian Sliding...

    Office of Scientific and Technical Information (OSTI)

    the geologic model are well suited for such an analysis. Unfortunately, current meshing tools are unable to automatically generate adequate hexahedral meshes for large numbers of...

  18. Serviceability of coiled tubing for sour oil and gas wells

    SciTech Connect (OSTI)

    Cayard, M.S.; Kane, R.D.

    1996-08-01

    Coiled tubing is an extremely useful tool in many well logging and workover applications in oil and gas production operations. Several important concerns regarding its use include the need for improved guidelines for the assessment of mechanical integrity, fatigue damage, and the effects of hydrogen sulfide in sour oil and gas production environments. This paper provides information regarding the use of coiled tubing in sour environments with particular emphasis on sulfide stress cracking, hydrogen induced cracking and stress-oriented hydrogen induced cracking and how they work synergistically with cyclic cold working of the steel tubing.

  19. Packer arrangements for oil wells and the like

    DOE Patents [OSTI]

    Harvey, Andrew C. (Waltham, MA); McFadden, David H. (Brookline, MA)

    1981-11-24

    The packer includes an elongated tubular casing, and a metal ring is disposed in its entirety within an annular recess in the casing. The recess has a circumferential opening extending entirely around the peripheral outer surface of the casing. Hydraulic fluid is flowed into the recess to apply pressure to the inner peripheral surface of the metal ring to expand the ring radially outwardly and force its outer peripheral surface through the circumferential opening and into annular sealing engagement with the opposed surface of the well casing.

  20. Well funneled nuclear structure landscape: renormalization

    E-Print Network [OSTI]

    A. Idini; G. Potel; F. Barranco; E. Vigezzi; R. A. Broglia

    2015-04-29

    A complete characterization of the structure of nuclei can be obtained by combining information arising from inelastic scattering, Coulomb excitation and $\\gamma-$decay, together with one- and two-particle transfer reactions. In this way it is possible to probe the single-particle and collective components of the nuclear many-body wavefunction resulting from their mutual coupling and diagonalising the low-energy Hamiltonian. We address the question of how accurately such a description can account for experimental observations. It is concluded that renormalizing empirically and on equal footing bare single-particle and collective motion in terms of self-energy (mass) and vertex corrections (screening), as well as particle-hole and pairing interactions through particle-vibration coupling allows theory to provide an overall, quantitative account of the data.

  1. Analysis of Post-Kyoto CO2 Emissions Trading Using Marginal Abatement Curves A. Denny Ellerman and Annelne Decaux

    E-Print Network [OSTI]

    Analysis of Post-Kyoto CO2 Emissions Trading Using Marginal Abatement Curves A. Denny Ellerman the advantages of emissions trading. In this paper, the authors derive MACs from EPPA, the MIT Joint Program the benefits of emissions trading in achieving the emission reduction targets implied by the Kyoto Protocol

  2. Surface uplift, fluvial incision, and geodynamics of plateau evolution, from the western margin of the Central Andean plateau

    E-Print Network [OSTI]

    Schildgen, Taylor F. (Taylor Frances)

    2008-01-01

    The Colca-Majes and Cotahuasi-Ocona rivers in southwest Peru that cut through the western margin of the Andean plateau en route to the Pacific Ocean incised canyons over 3 km deep in response to late Cenozoic surface uplift. ...

  3. Late-Pliocene timing of Corinth (Greece) rift-margin fault migration M.R. Leeder a,

    E-Print Network [OSTI]

    Utrecht, Universiteit

    Late-Pliocene timing of Corinth (Greece) rift-margin fault migration M.R. Leeder a, , G.H. Mack b Mexico State University, Las Cruces, NM 88003, USA c NERC Isotope Geosciences Laboratory, Kingsley Dunham Centre, Keyworth, Nottingham, NG12 5GG, UK d Geochronology Research Laboratory, New Mexico Bureau

  4. IEEE TRANSACTIONS ON POWER SYSTEMS, VOL. 29, NO. 1, JANUARY 2014 203 Distribution Locational Marginal Pricing for Optimal

    E-Print Network [OSTI]

    Oren, Shmuel S.

    Marginal Pricing for Optimal Electric Vehicle Charging Management Ruoyang Li, Student Member, IEEE, Qiuwei Wu, Member, IEEE, and Shmuel S. Oren, Fellow, IEEE Abstract--This paper presents an integrated vehicle (EV) loads in future power systems. In the proposed approach, the distribution system op- erator

  5. Well-to-wheels energy use and greenhouse gas emissions analysis of plug-in hybrid electric vehicles.

    SciTech Connect (OSTI)

    Elgowainy, A.; Burnham, A.; Wang, M.; Molburg, J.; Rousseau, A.; Energy Systems

    2009-03-31

    Researchers at Argonne National Laboratory expanded the Greenhouse gases, Regulated Emissions, and Energy use in Transportation (GREET) model and incorporated the fuel economy and electricity use of alternative fuel/vehicle systems simulated by the Powertrain System Analysis Toolkit (PSAT) to conduct a well-to-wheels (WTW) analysis of energy use and greenhouse gas (GHG) emissions of plug-in hybrid electric vehicles (PHEVs). The WTW results were separately calculated for the blended charge-depleting (CD) and charge-sustaining (CS) modes of PHEV operation and then combined by using a weighting factor that represented the CD vehicle-miles-traveled (VMT) share. As indicated by PSAT simulations of the CD operation, grid electricity accounted for a share of the vehicle's total energy use, ranging from 6% for a PHEV 10 to 24% for a PHEV 40, based on CD VMT shares of 23% and 63%, respectively. In addition to the PHEV's fuel economy and type of on-board fuel, the marginal electricity generation mix used to charge the vehicle impacted the WTW results, especially GHG emissions. Three North American Electric Reliability Corporation regions (4, 6, and 13) were selected for this analysis, because they encompassed large metropolitan areas (Illinois, New York, and California, respectively) and provided a significant variation of marginal generation mixes. The WTW results were also reported for the U.S. generation mix and renewable electricity to examine cases of average and clean mixes, respectively. For an all-electric range (AER) between 10 mi and 40 mi, PHEVs that employed petroleum fuels (gasoline and diesel), a blend of 85% ethanol and 15% gasoline (E85), and hydrogen were shown to offer a 40-60%, 70-90%, and more than 90% reduction in petroleum energy use and a 30-60%, 40-80%, and 10-100% reduction in GHG emissions, respectively, relative to an internal combustion engine vehicle that used gasoline. The spread of WTW GHG emissions among the different fuel production technologies and grid generation mixes was wider than the spread of petroleum energy use, mainly due to the diverse fuel production technologies and feedstock sources for the fuels considered in this analysis. The PHEVs offered reductions in petroleum energy use as compared with regular hybrid electric vehicles (HEVs). More petroleum energy savings were realized as the AER increased, except when the marginal grid mix was dominated by oil-fired power generation. Similarly, more GHG emissions reductions were realized at higher AERs, except when the marginal grid generation mix was dominated by oil or coal. Electricity from renewable sources realized the largest reductions in petroleum energy use and GHG emissions for all PHEVs as the AER increased. The PHEVs that employ biomass-based fuels (e.g., biomass-E85 and -hydrogen) may not realize GHG emissions benefits over regular HEVs if the marginal generation mix is dominated by fossil sources. Uncertainties are associated with the adopted PHEV fuel consumption and marginal generation mix simulation results, which impact the WTW results and require further research. More disaggregate marginal generation data within control areas (where the actual dispatching occurs) and an improved dispatch modeling are needed to accurately assess the impact of PHEV electrification. The market penetration of the PHEVs, their total electric load, and their role as complements rather than replacements of regular HEVs are also uncertain. The effects of the number of daily charges, the time of charging, and the charging capacity have not been evaluated in this study. A more robust analysis of the VMT share of the CD operation is also needed.

  6. Hydraulic Fracture Stimulation and Acid Treatment of Well Baca 20; Geothermal Reservoir Well Stimulation Program

    SciTech Connect (OSTI)

    None

    1983-07-01

    The U.S. Department of Energy-sponsored Geothermal Reservoir Well Stimulation Program was initiated in February 1979 to pursue industry interest in geothermal well stimulation work and to develop technical expertise in areas directly related to geothermal well stimulation activities. This report provides an overview of the two experiments conducted in the high-temperature reservoir in Baca, New Mexico. The report discusses resource and reservoir properties, and provides a description of the stimulation experiment, a description of the treatment evaluation, and a summary of the experiment costs. (DJE-2005)

  7. Using coiled tubing in HP/HT corrosive gas wells

    SciTech Connect (OSTI)

    1997-06-01

    High-yield-strength (100,000 psi) coiled tubing (CT) material has allowed for CT intervention in Mobile Bay Norphlet completions. These wells are approximately 22,000-ft-vertical-depth, high-pressure, hydrogen sulfide (H{sub 2}S) gas wells. Operations performed on the Norphlet wells include a scale cleanout to approximately 22,000 ft, a hydrochloric acid (HCl) job at 415 F, and buildup removal from a safety valve. The scale cleanout was performed first with a spiral wash tool. The well was killed with 10-lbm/gal sodium bromide (NaBr) brine; the same brine was used for cleanout fluid. Cost savings of 60% were realized. A HCl matrix acid job at 415 F was performed next, followed by a scale cleanout across the downhole safety valve. The safety valve was cleared of debris in 1 operational day. Estimated cost of the CT operation was 5 to 10% less than that of a rig workover. The 100,000-psi-yield Ct material used for the Mobile Bay operations does not comply with the (NACE) Standard MR-0175. But on the basis of extensive laboratory testing by the CT manufacturer, the decision was made that the material would pass a modified test performed with decreased H{sub 2}S levels. A maximum level of 400 ppm H{sub 2}S was determined as the safe working limit. Because the maximum H{sub 2}S content in the wells described later was 120 ppm, the risk of sulfide-stress cracking (SSC) was considered acceptably low. Elevated bottomhole temperatures (BHT`s) increase the corrosion rate of metals exposed to corrosives. Extensive laboratory testing of corrosion inhibitors allowed for design of a matrix-acidizing treatment to remove near-wellbore damage caused by lost zinc bromide (ZnBr) completion brine.

  8. Cement fatigue and HPHT well integrity with application to life of well prediction 

    E-Print Network [OSTI]

    Ugwu, Ignatius Obinna

    2009-05-15

    In order to keep up with the world’s energy demands, oil and gas producing companies have taken the initiative to explore offshore reserves or drill deeper into previously existing wells. The consequence of this, however, ...

  9. The rehabilitation of monitoring wells clogged by calcite precipitation and drilling mud

    SciTech Connect (OSTI)

    Kroening, D.E.; Snipes, D.S.; Brame, S.E.; Hodges, R.A.; Price, V.; Temples, T.J.

    1996-08-01

    Based on aquifer performance tests, 13 out of 15 wells situated at the Mixed Waste Disposal (MWD) area located at the Savannah River site, South Carolina, exhibited high skin factors and low well efficiencies indicative of severely damaged wells. The use of damaged wells in aquifer testing can lead to inaccurate determinations of aquifer properties, and such wells are unusable in future remediation programs. Moreover, damaged wells can go dry during purging, thus compromising sample collection. Pump tests, chemical analyses, and biological investigations revealed that the poor well performance at MWD was attributable to calcite precipitation on the well screen and drilling mud in the filter pack. The calcite problem resulted from improper well installation, and the drilling mud in the filter pack was due to inadequate well development. Experimental rehabilitation procedures employed on two wells, MWD 5A and 1A, included acidification, swabbing, introduction of surfactants, and surging. Treatment of the wells substantially improved well yields, skin factors, and well efficiencies. Moreover, well rehabilitation was determined to be a reasonable alternative to drilling new wells at the MWD wellfield.

  10. What To Include In The Whistleblower Complaint? | National Nuclear...

    National Nuclear Security Administration (NNSA)

    Apply for Our Jobs Our Jobs Working at NNSA Blog Home About Us Our Operations Management and Budget Whistleblower Program What To Include In The Whistleblower Complaint?...

  11. Introduction to Small-Scale Photovoltaic Systems (Including RETScreen...

    Open Energy Info (EERE)

    Introduction to Small-Scale Photovoltaic Systems (Including RETScreen Case Study) (Webinar) Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Introduction to Small-Scale...

  12. Including Retro-Commissioning in Federal Energy Savings Performance...

    Broader source: Energy.gov (indexed) [DOE]

    More Documents & Publications Including Retro-Commissioning in Federal Energy Savings Performance Contracts Enabling Mass-Scale Financing for Federal Energy, Water, and...

  13. Numerical simulations for low energy nuclear reactions including...

    Office of Scientific and Technical Information (OSTI)

    Numerical simulations for low energy nuclear reactions including direct channels to validate statistical models Citation Details In-Document Search Title: Numerical simulations for...

  14. U-182: Microsoft Windows Includes Some Invalid Certificates

    Broader source: Energy.gov [DOE]

    The operating system includes some invalid intermediate certificates. The vulnerability is due to the certificate authorities and not the operating system itself.

  15. Journal of the Geological Society, London, Vol. 162, 2005, pp. 135146. Printed in Great Britain. Subsidence history of the north Indian continental margin, ZanskarLadakh

    E-Print Network [OSTI]

    Watts, A. B. "Tony"

    . 135 Subsidence history of the north Indian continental margin, Zanskar­Ladakh Himalaya, NW India R. I of the tectonic subsidence and uplift through the pre- collisional history of the margin have been constructed.2. This model accounts for the general exponential decrease in the backstripped tectonic subsidence. The model

  16. New Views of the U.S. Atlantic Margin Mapped for UNCLOS Applications. James V. Gardner, Larry A. Mayer, Andy Armstrong, University of New Hampshire,

    E-Print Network [OSTI]

    New Hampshire, University of

    areas of the lower slope. The large-area mapping required to support an UNCLOS submission, generates for the next generation of continental-margin studies. As part of the U.S. UNCLOS effort, the entire U to channels farther upslope. #12;Failures are common in the northern 80\\% of the margin. Some failures

  17. Shutdown Margin for High Conversion BWRs Operating in Th-233U Fuel Cycle

    E-Print Network [OSTI]

    Yaniv Shaposhnik; Eugene Shwageraus; Ezra Elias

    2013-09-27

    Several reactivity control system design options are explored in order to satisfy shutdown margin (SDM) requirements in a high conversion BWRs operating in Th-233U fuel cycle (Th-RBWR). The studied has an axially heterogeneous fuel assembly structure with a single fissile zone sandwiched between two fertile blanket zones. The utilization of an originally suggested RBWR Y-shape control rod in Th-RBWR is shown to be insufficient for maintaining adequate SDM to balance the high negative reactivity feedbacks, while maintaining fuel breeding potential, core power rating, and minimum Critical Power Ratio (CPR). Instead, an alternative assembly design, also relying on heterogeneous fuel zoning, is proposed for achieving fissile inventory ratio (FIR) above unity, adequate SDM and meeting minimum CPR limit at thermal core output matching the ABWR power. The new concept was modeled as a single 3-dimensional fuel assembly having reflective radial boundaries, using the BGCore system, which consists of the MCNP code coupled with fuel depletion and thermo-hydraulic feedback modules.

  18. Subsea well template for directional drilling

    SciTech Connect (OSTI)

    Goldsmith, R.G.

    1988-07-05

    A method is described for drilling widely spaced boreholes into a hydrocarbon producing subsea formation comprising the steps of: positioning a subsea drilling template on the bottom of a body of water, the subsea drilling template including laterally disposed, substantially cylindrical drilling guides having a longitudinal axis wherein at least one of the drilling guides has its longitudinal axis disposed at an angle of less than 90/sup 0/ relative to a horizontal plane passing through the subsea drilling template; mooring a drilling vessel floating on the surface of the body of water in a first position relative to the subsea drilling template using a plurality of mooring catenaries; extending a drill string from the floating vessel to the subsea template, the drill string passing into the one of the drilling guides along its longitudinal axis which is disposed at an angle of less than 90/sup 0/; drilling a borehole below the template into the hydrocarbon producing subsea formation; repositioning the drilling vessel to another position relative to the subsea template by adjusting the mooring catenaries; extending the drill string from the vessel into another of the drilling guides; drilling another borehole below the template; and repeating the steps of repositioning the drilling vessel, extending the drill string and drilling the widely spaced boreholes.

  19. 1034 BOOK REVIEWS include palaeontological evidence for the initiation of cooling

    E-Print Network [OSTI]

    Fischlin, Andreas

    middle Eocene. The final paper (Hambrey & Smellie) presents evidence for the response of Antarctica. As would be expected from the Geological Society Publishing House, this is a high quality, well structured studies across the whole of the Southern Hemisphere, including pro- posed offshore drilling programmes (e

  20. Including Atmospheric Layers in Vegetation and Urban Offline Surface Schemes VALE RY MASSON AND YANN SEITY

    E-Print Network [OSTI]

    is able to model the 2-m temperature accurately, as well as the 10-m wind, without any use of analyticalIncluding Atmospheric Layers in Vegetation and Urban Offline Surface Schemes VALE´ RY MASSON coupling between atmospheric-model levels and surface-scheme levels, the coupling proposed here remains

  1. Subsets of Women With Close or Positive Margins After Breast-Conserving Surgery With High Local Recurrence Risk Despite Breast Plus Boost Radiotherapy

    SciTech Connect (OSTI)

    Lupe, Krystine; Truong, Pauline T.; Alexander, Cheryl; Lesperance, Mary; Speers, Caroline; Tyldesley, Scott

    2011-11-15

    Purpose: (1) To examine the effect of surgical margin status on local recurrence (LR) and survival following breast-conserving therapy; (2) To identify subsets with close or positive margins with high LR risk despite whole breast radiotherapy (RT) plus boost. Methods and Materials: Subjects were 2,264 women with pT1-3, any N, M0 invasive breast cancer, treated with breast-conserving surgery and whole breast {+-} boost RT. Five-year Kaplan-Meier (KM) LR, breast cancer-specific and overall survival (BCSS and OS) were compared between cohorts with negative (n = 1,980), close (n = 222), and positive (n = 62) margins. LR rates were analyzed according to clinicopathologic characteristics. Multivariable Cox regression modeling and matched analysis of close/positive margin cases and negative margin controls were performed. Results: Median follow-up was 5.2 years. Boost RT was used in 92% of patients with close or positive margins. Five-year KM LR rates in the negative, close and positive margin cohorts were 1.3%, 4.0%, and 5.2%, respectively (p = 0.001). BCSS and OS were similar in the three margin subgroups. In the close/positive margin cohort, LR rates were 10.2% with age <45 years, 11.8% with Grade III, 11.3% with lymphovascular invasion (LVI), and 26.3% with {>=}4 positive nodes. Corresponding rates in the negative margin cohort were 2.3%, 2.4%, 1.0%, and 2.4%, respectively. On Cox regression analysis of the entire cohort, close or positive margin, Grade III histology, {>=}4 positive nodes, and lack of systemic therapy were significantly associated with higher LR risk. When close/positive margin cases were matched to negative margin controls, the difference in 5-year LR remained significant (4.25% vs. 0.7%, p < 0.001). Conclusions: On univariable analysis, subsets with close or positive margins, in combination with age <45 years, Grade III, LVI, and {>=}4 positive nodes, have 5-year LR >10% despite whole breast plus boost RT. These patients should be considered for more definitive surgery.

  2. Controlling formation fines at their sources to maintain well productivity

    SciTech Connect (OSTI)

    Nguyen, P.D.; Weaver, J.D.; Rickman, R.D.; Dusterhoft, R.G.; Parker, M.A.

    2007-05-15

    Migration of formation fines has been shown to cause production decline in many wells. Despite the availability of new downhole tools for use in well stimulation and completion, the ability to sustain desired production levels is often plagued with fines migration problems. The solution to this problem is appropriate treatment to mitigate fines migration at its source. This paper describes the use of an ultra-thin tackifying agent (UTTA) for stabilizing fines in high-rate producing or injection wells. This UTTA is applied as part of an initial prepad in fracturing or gravel-packing operations, as a remedial treatment, or as a post-treatment following acid fracturing or matrix acidizing treatments. The primary purpose of UTTA application is to immobilize formation fines so that they will not detach, migrate with flowing fluids, plug the pore channels, and reduce the flow path permeability. Results of laboratory testing indicate that the UTTA system is applicable to most types of formation fines, including coals, sandstones, and carbonates. Once injected into the formation matrix or proppant pack, the UTTA forms a thin film on formation surfaces, encapsulating the fines. Capillary action helps pull the tackifier into the contact points, fixing the particulate in place without plugging the pore throat. The UTTA does not require a shut-in time after its application. The thin film tackifier does not harden, but remains flexible, enhancing the ability of a formation to withstand stress cycling and allowing the formation to handle high shear stress during high flow rates.

  3. Completion Report for Well ER-8-1

    SciTech Connect (OSTI)

    Bechtel Nevada

    2004-11-01

    Well ER-8-1 was drilled for the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office in support of the Nevada Environmental Restoration Project at the Nevada Test Site, Nye County, Nevada. This well was drilled in October and November of 2002 as part of a Hydrogeologic investigation program for the Yucca Flat/Climax Mine Corrective Action Unit in the northeastern portion of the Nevada Test Site. Well ER-8-1 is located at the north end of Yucca Flat approximately 580 meters south-southeast of the surface exposure of the Climax granitic intrusive. Detailed lithologic descriptions with stratigraphic assignments are included in this report. These are based on composite drill cuttings samples collected every 3 meters, and 21 sidewall samples taken at various depths between 351.1 and 573.0 meters, supplemented by incomplete geophysical log data. Detailed petrographic, geochemical, and mineralogical studies of rock samples were conducted on 22 samples of drill cuttings. Drilling began in tuffaceous alluvium, and the borehole penetrated Tertiary age bedded tuffs of the Volcanics of Oak Spring Butte and carbonate sediments of Paleozoic age, which were encountered at a depth of 334 meters. The borehole unexpectedly penetrated granite at the depth of 538.9 meters in which drilling was stopped. Contact metamorphic rocks and intrusive dikes associated with the Cretaceous-age granitic intrusive and at least one significant fault zone were encountered.

  4. Apparatus for operating a gas and oil producing well

    SciTech Connect (OSTI)

    Wynn, S. R.

    1985-07-02

    Apparatus is disclosed for automatically operating a gas and oil producing well of the plunger lift type, including a comparator for comparing casing and tubing pressures, a device for opening the gas delivery valve when the difference between casing and tubing pressure is less than a selected minimum value, a device for closing the gas discharge valve when casing pressure falls below a selected casing bleed value, an arrival sensor switch for initially closing the fluid discharge valve when the plunger reaches the upper end of the tubing, and a device for reopening the fluid discharge valve at the end of a given downtime period in the event that the level of oil in the tubing produces a pressure difference greater than the given minimum differential value, and the casing pressure is greater than lift pressure. The gas discharge valve is closed if the pressure difference exceeds a selected maximum value, or if the casing pressure falls below a selected casing bleed value. The fluid discharge valve is closed if tubing pressure exceeds a maximum safe value. In the event that the plunger does not reach the upper end of the tubing during a selected uptime period, a lockout indication is presented on a visual display device, and the well is held shut-in until the well differential is forced down to the maximum differential setting of the device. When this occurs, the device will automatically unlock and normal cycling will resume.

  5. Emergence of the Persistent Spin Helix in Semiconductor Quantum Wells

    SciTech Connect (OSTI)

    Koralek, Jake; Weber, Chris; Orenstein, Joe; Bernevig, Andrei; Zhang, Shoucheng; Mack, Shawn; Awschalom, David

    2011-08-24

    According to Noether's theorem, for every symmetry in nature there is a corresponding conservation law. For example, invariance with respect to spatial translation corresponds to conservation of momentum. In another well-known example, invariance with respect to rotation of the electron's spin, or SU(2) symmetry, leads to conservation of spin polarization. For electrons in a solid, this symmetry is ordinarily broken by spin-orbit (SO) coupling, allowing spin angular momentum to flow to orbital angular momentum. However, it has recently been predicted that SU(2) can be recovered in a two-dimensional electron gas (2DEG), despite the presence of SO coupling. The corresponding conserved quantities include the amplitude and phase of a helical spin density wave termed the 'persistent spin helix' (PSH). SU(2) is restored, in principle, when the strength of two dominant SO interactions, the Rashba ({alpha}) and linear Dresselhaus ({beta}{sub 1}), are equal. This symmetry is predicted to be robust against all forms of spin-independent scattering, including electron-electron interactions, but is broken by the cubic Dresselhaus term ({beta}{sub 3}) and spin-dependent scattering. When these terms are negligible, the distance over which spin information can propagate is predicted to diverge as {alpha} {yields} {beta}{sub 1}. Here we observe experimentally the emergence of the PSH in GaAs quantum wells (QW's) by independently tuning {alpha} and {beta}{sub 1}. Using transient spin-grating spectroscopy (TSG), we find a spin-lifetime enhancement of two orders of magnitude near the symmetry point. Excellent quantitative agreement with theory across a wide range of sample parameters allows us to obtain an absolute measure of all relevant SO terms, identifying {beta}{sub 3} as the main SU(2) violating term in our samples. The tunable suppression of spin-relaxation demonstrated in this work is well-suited for application to spintronics.

  6. PSERC 97-12 "Thermal Unit Commitment Including

    E-Print Network [OSTI]

    PSERC 97-12 "Thermal Unit Commitment Including Optimal AC Power Flow Constraints" Carlos Murillo-562-3966. #12;Thermal Unit Commitment Including Optimal AC Power Flow Constraints Carlos Murillo S anchez Robert a new algorithm for unit commitment that employs a Lagrange relaxation technique with a new augmentation

  7. Summer Conference Participant Registration Fee: $200 Includes the following

    E-Print Network [OSTI]

    Tullos, Desiree

    Summer Conference Participant Registration Fee: $200 Includes the following: Lodging for Wednesday on Wednesday, Thursday, and Friday Brunch on Saturday Summer Conference T-shirt Class materials Congress Only only (although they are encouraged to attend the entire conference). This fee includes the following

  8. Solar Energy Education. Reader, Part II. Sun story. [Includes glossary

    SciTech Connect (OSTI)

    Not Available

    1981-05-01

    Magazine articles which focus on the subject of solar energy are presented. The booklet prepared is the second of a four part series of the Solar Energy Reader. Excerpts from the magazines include the history of solar energy, mythology and tales, and selected poetry on the sun. A glossary of energy related terms is included. (BCS)

  9. Energy Transitions: A Systems Approach Including Marcellus Shale Gas Development

    E-Print Network [OSTI]

    Chen, Tsuhan

    Energy Transitions: A Systems Approach Including Marcellus Shale Gas Development A Report Transitions: A Systems Approach Including Marcellus Shale Gas Development Executive Summary In the 21st the Marcellus shale In addition to the specific questions identified for the case of Marcellus shale gas in New

  10. Exploratory Well At North Brawley Geothermal Area (Matlick &...

    Open Energy Info (EERE)

    Well Activity Date 1975 - 1980 Usefulness useful DOE-funding Unknown Exploration Basis Deep exploratory wells were drilled after a phase of thermal gradient wells helped narrow...

  11. ARSENIC IN PRIVATE WELLS IN NH YEAR 1 FINAL REPORT

    E-Print Network [OSTI]

    Bucci, David J.

    performed geospatial analysis of the well water arsenic estimates and survey results and produced the maps............................................................................................... 8 Well water treatment .................................................................................................. 7 Well water quality

  12. Multifunctional Corrosion-resistant Foamed Well Cement Composites...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Multifunctional Corrosion-resistant Foamed Well Cement Composites Multifunctional Corrosion-resistant Foamed Well Cement Composites Multifunctional Corrosion-resistant Foamed Well...

  13. Energetic Materials for EGS Well Stimulation (solids, liquids...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Energetic Materials for EGS Well Stimulation (solids, liquids, gases) Energetic Materials for EGS Well Stimulation (solids, liquids, gases) Energetic Materials for EGS Well...

  14. [Article 1 of 7: Motivates and Includes the Consumer

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    been lucky in the past, but the future will be more challenging. Today's electric system was not designed to handle extensive, well-organized acts of terrorism aimed at...

  15. Articles which include chevron film cooling holes, and related processes

    DOE Patents [OSTI]

    Bunker, Ronald Scott; Lacy, Benjamin Paul

    2014-12-09

    An article is described, including an inner surface which can be exposed to a first fluid; an inlet; and an outer surface spaced from the inner surface, which can be exposed to a hotter second fluid. The article further includes at least one row or other pattern of passage holes. Each passage hole includes an inlet bore extending through the substrate from the inlet at the inner surface to a passage hole-exit proximate to the outer surface, with the inlet bore terminating in a chevron outlet adjacent the hole-exit. The chevron outlet includes a pair of wing troughs having a common surface region between them. The common surface region includes a valley which is adjacent the hole-exit; and a plateau adjacent the valley. The article can be an airfoil. Related methods for preparing the passage holes are also described.

  16. Well test imaging - a new method for determination of boundaries from well test data

    SciTech Connect (OSTI)

    Slevinsky, B.A.

    1997-08-01

    A new method has been developed for analysis of well test data, which allows the direct calculation of the location of arbitrary reservoir boundaries which are detected during a well test. The method is based on elements of ray tracing and information theory, and is centered on the calculation of an instantaneous {open_quote}angle of view{close_quote} of the reservoir boundaries. In the absence of other information, the relative reservoir shape and boundary distances are retrievable in the form of a Diagnostic Image. If other reservoir information, such as 3-D seismic, is available; the full shape and orientation of arbitrary (non-straight line or circular arc) boundaries can be determined in the form of a Reservoir Image. The well test imaging method can be used to greatly enhance the information available from well tests and other geological data, and provides a method to integrate data from multiple disciplines to improve reservoir characterization. This paper covers the derivation of the analytical technique of well test imaging and shows examples of application of the technique to a number of reservoirs.

  17. Well Completion Report for Well ER-20-11, Corrective Action Units 101 and 102: Central and Western Pahute Mesa

    SciTech Connect (OSTI)

    NSTec Environmental Management

    2013-02-27

    Well ER-20-11 was drilled for the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office in support of the Nevada Environmental Management Operations Underground Test Area (UGTA) Activity at the Nevada National Security Site (formerly Nevada Test Site), Nye County, Nevada. The well was drilled in September 2012 as part of the Central and Western Pahute Mesa Corrective Action Unit Phase II drilling program. Well ER-20-11 was constructed to further investigate the nature and extent of radionuclidecontaminated groundwater encountered in two nearby UGTA wells, to help define hydraulic and transport parameters for the contaminated Benham aquifer, and to provide data for the UGTA hydrostratigraphic framework model. The 44.5-centimeter (cm) surface hole was drilled to a depth of 520.0 meters (m) and cased with 34.0-cm casing to 511.5 m. The hole diameter was then decreased to 31.1 cm, and the borehole was drilled to a total depth of 915.6 m. The hole was completed to allow access for hydrologic testing and sampling in the target aquifer, which is a lava-flow aquifer known as the Benham aquifer. The completion casing string, set to the depth of 904.3 m, consists of a string of 6?-inch (in.) stainless-steel casing hanging from a string of 7?-in. carbon-steel casing. The stainless-steel casing has one slotted interval at 796.3 to 903.6 m. One piezometer string was installed, which consists of 2?-in. stainless-steel tubing that hangs from 2?-in. carbon-steel tubing via a crossover sub. This string was landed at 903.8 m and is slotted in the interval 795.3 to 903.1 m. Data collected during and shortly after hole construction include composite drill cuttings samples collected every 3.0 m, various geophysical logs, fluid samples (for groundwater chemistry analysis and tritium measurements), and water-level measurements. The well penetrated 915.6 m of Tertiary volcanic rock, including one saturated lava flow aquifer. Measurements on samples taken from the undeveloped well indicated elevated tritium levels within the Benham aquifer. The maximum tritium level measured with field equipment was 146,131 picocuries per liter from a sample obtained at the depth of 912.0 m. The fluid level was measured in the piezometer string at a depth of 504.5 m on September 26, 2012. All Fluid Management Plan (FMP) requirements for Well ER-20-11 were met. Analysis of monitoring samples and FMP confirmatory samples indicated that fluids generated during drilling at Well ER-20-11 met the FMP criteria for discharge to an unlined sump or designated infiltration area. Well development, hydrologic testing, and sampling will be conducted at a later date.

  18. Volitional Intentional Activities and Subjective Well-Being: The Mediating Influence of Personality 

    E-Print Network [OSTI]

    Birkett, Nick

    2008-06-27

    The effect of goal setting and achievement on subjective well-being was explored to test and extend the “Architecture of Sustainable Happiness” model (Lyubomirsky et al., 2005). Mediating factors, including personality were also considered...

  19. The Dynamics of Fluid Flow and Associated Chemical Fluxes at Active Continental Margins

    E-Print Network [OSTI]

    Solomon, Evan A

    2007-01-01

    plate-boundary fault, Barbados accretionary complex. Geologytwo-well experiment in the Barbados accretionary complex. J.volcano field seaward of the Barbados accretionary wedge, J.

  20. The Dynamics of fluid flow and associated chemical fluxes at active continental margins

    E-Print Network [OSTI]

    Solomon, Evan Alan

    2007-01-01

    plate-boundary fault, Barbados accretionary complex. Geologytwo-well experiment in the Barbados accretionary complex. J.volcano field seaward of the Barbados accretionary wedge, J.

  1. Performance of a well with lateral and vertical wellbores 

    E-Print Network [OSTI]

    Abdat, Toriq

    2002-01-01

    analysis of actual well test data is also provided. For horizontal wells, we focus on analysis pressure solution for pseudoradial flow. Limited entry slanted wells are considered in this work by comparing wells with different angles and evaluating...

  2. Including Retro-Commissioning in Federal Energy Savings Performance...

    Energy Savers [EERE]

    the cost of the survey. Developing a detailed scope of work and a fixed price for this work is important to eliminate risk to the Agency and the ESCo. Including a detailed scope...

  3. T-603: Mac OS X Includes Some Invalid Comodo Certificates

    Broader source: Energy.gov [DOE]

    The operating system includes some invalid certificates. The vulnerability is due to the invalid certificates and not the operating system itself. Other browsers, applications, and operating systems are affected.

  4. FINITE ELEMENT ANALYSIS OF STEEL WELDED COVERPLATE INCLUDING COMPOSITE DOUBLERS

    E-Print Network [OSTI]

    Petri, Brad

    2008-05-15

    With the increasing focus on welded bridge members resulting in crack initiation and propagation, there is a large demand for creative solutions. One of these solutions includes the application of composite doublers over ...

  5. Title 16 USC 818 Public Lands Included in Project - Reservation...

    Open Energy Info (EERE)

    of Lands From Entry Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- StatuteStatute: Title 16 USC 818 Public Lands Included in Project...

  6. Including costs of supply chain risk in strategic sourcing decisions

    E-Print Network [OSTI]

    Jain, Avani

    2009-01-01

    Cost evaluations do not always include the costs associated with risks when organizations make strategic sourcing decisions. This research was conducted to establish and quantify the impact of risks and risk-related costs ...

  7. An Enhanced In-Vessel Core Catcher for Improving In-Vessel Retention Margins

    SciTech Connect (OSTI)

    Joy L. Rempe

    2005-11-01

    In-vessel retention (IVR) of core melt that may relocate to the lower head of a reactor vessel is a key severe accident management strategy adopted by some operating nuclear power plants and proposed for several advanced light water reactors. A U.S.-Korean International Nuclear Energy Research Initiative project has been initiated to explore design enhancements that could increase the margin for IVR for advanced reactors with higher power levels [up to 1500 MW(electric)]. As part of this effort, an enhanced in-vessel core catcher is being designed and evaluated. To reduce cost and simplify manufacture and installation, this new core catcher design consists of several interlocking sections that are machined to fit together when inserted into the lower head. If needed, the core catcher can be manufactured with holes to accommodate lower head penetrations. Each section of the core catcher consists of two material layers with an option to add a third layer (if deemed necessary). The first is a base material that has the capability to support and contain the mass of core materials that may relocate during a severe accident; the second is an oxide coating on top of the base material, which resists interactions with high-temperature core materials; and the third is an optional coating on the bottom side of the base material to protect it from oxidation during the lifetime of the reactor. This paper summarizes results from the invessel core catcher design and evaluation efforts, focusing on recently obtained results from materials interaction tests and prototypic testing activities.

  8. Development of an Enhanced Core Catcher for Improving In-Vessel Retention Margins

    SciTech Connect (OSTI)

    Rempe, J.L. [Idaho National Engineering and Environmental Laboratory (United States); Condie, K.G. [Idaho National Engineering and Environmental Laboratory (United States); Knudson, D.L. [Idaho National Engineering and Environmental Laboratory (United States); Suh, K.Y. [Seoul National University (Korea, Republic of); Cheung, F.B. [The Pennsylvania State University (United States); Kim, S.B. [Korea Atomic Energy Research Institute (Korea, Republic of)

    2005-11-15

    In-vessel retention (IVR) of core melt that may relocate to the lower head of a reactor vessel is a key severe accident management strategy adopted by some operating nuclear power plants and proposed for several advanced light water reactors. A U.S.-Korean International Nuclear Energy Research Initiative project has been initiated to explore design enhancements that could increase the margin for IVR for advanced reactors with higher power levels [up to 1500 MW(electric)]. As part of this effort, an enhanced in-vessel core catcher is being designed and evaluated. To reduce cost and simplify manufacture and installation, this new core catcher design consists of several interlocking sections that are machined to fit together when inserted into the lower head. If needed, the core catcher can be manufactured with holes to accommodate lower head penetrations. Each section of the core catcher consists of two material layers with an option to add a third layer (if deemed necessary). The first is a base material that has the capability to support and contain the mass of core materials that may relocate during a severe accident; the second is an oxide coating on top of the base material, which resists interactions with high-temperature core materials; and the third is an optional coating on the bottom side of the base material to protect it from oxidation during the lifetime of the reactor. This paper summarizes results from the in-vessel core catcher design and evaluation efforts, focusing on recently obtained results from materials interaction tests and prototypic testing activities.

  9. The North American Atlantic outer continental margin landslides data base: Summary and observations

    SciTech Connect (OSTI)

    Booth, J.S.; O'Leary, D.W. (Geological Survey, Woods Hole, MA (USA))

    1990-06-01

    A compilation of published data from 179 Quaternary mass movement features was analyzed to determine the common attributes of the slides, to reveal general trends, and to classify and compare slide types. The data set was derived primarily from high-resolution, seismic-reflection data and sidescan-sonar images. In general, evidence of slope failure is found throughout the length of the margin and in all water depths. Slides have occurred on slope angles ranging from 1{degree} to 30{degree} (avg.{approximately}5{degree}); they vary in width from 0.2 to 50 km (avg. {approximately}4 km) and in length from 0.3 to 380 km (avg. {approximately}10 km) and have been reported to be as thick as 650 m. They are slightly more prevalent on open slopes than in other physiographic settings (e.g., canyons, ridges, spurs) and more commonly translational than rotational (i.e., slumps). The slides show no striking affinity for a particular depth range, either in the data set as a whole or when analyzed in terms of physiographic setting, size, slope angle, or other basis for classification. Comparison of slides found on the open slope with those found within canyons shows that the average open slope slide tends to occur at lower slope angles and is much larger (by an order of magnitude) than the average canyon slide. Regardless of the physiographic setting or other characteristic, large-scale slides (area >100 km{sup 2}) rather than small-scale slides (area <10 km{sup 2}) tend to be associated with gentle slopes ({approximately}3-4{degree}) Similarly, slides generated on steep slopes ({>=}10{degree}), regardless of other attributes, tend to be small (avg. area <5 km{sup 2}). With few exceptions, comparisons between slide categories show only minor differences.

  10. Segmentation of complex geophysical structures with well Running title: Image segmentation with well data.

    E-Print Network [OSTI]

    Boyer, Edmond

    gap for reservoir characterization. Morevoer, it is well known that interpre- tation of faults for instance Monsen et al. [24], Randen et al. [28]). More precisely, the fault extraction from 3D data is of key importance in reservoir characterization: detailed knowledge of the fault system may provide

  11. Hybrid powertrain system including smooth shifting automated transmission

    DOE Patents [OSTI]

    Beaty, Kevin D.; Nellums, Richard A.

    2006-10-24

    A powertrain system is provided that includes a prime mover and a change-gear transmission having an input, at least two gear ratios, and an output. The powertrain system also includes a power shunt configured to route power applied to the transmission by one of the input and the output to the other one of the input and the output. A transmission system and a method for facilitating shifting of a transmission system are also provided.

  12. Limited Personal Use of Government Office Equipment including Information Technology

    Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

    2005-01-07

    The Order establishes requirements and assigns responsibilities for employees' limited personal use of Government resources (office equipment and other resources including information technology) within DOE, including NNSA. The Order is required to provide guidance on appropriate and inappropriate uses of Government resources. This Order was certified 04/23/2009 as accurate and continues to be relevant and appropriate for use by the Department. Certified 4-23-09. No cancellation.

  13. Light Water Reactor Sustainability Program Technical Basis Guide Describing How to Perform Safety Margin Configuration Risk Management

    SciTech Connect (OSTI)

    Curtis Smith; James Knudsen; Bentley Harwood

    2013-08-01

    The INL has carried out a demonstration of the RISMC approach for the purpose of configuration risk management. We have shown how improved accuracy and realism can be achieved by simulating changes in risk – as a function of different configurations – in order to determine safety margins as the plant is modified. We described the various technical issues that play a role in these configuration-based calculations with the intent that future applications can take advantage of the analysis benefits while avoiding some of the technical pitfalls that are found for these types of calculations. Specific recommendations have been provided on a variety of topics aimed at improving the safety margin analysis and strengthening the technical basis behind the analysis process.

  14. Soil Carbon Change and Net Energy Associated with Biofuel Production on Marginal Lands: A Regional Modeling Perspective

    SciTech Connect (OSTI)

    Bandaru, Varaprasad; Izaurralde, Roberto C.; Manowitz, David H.; Link, Robert P.; Zhang, Xuesong; Post, W. M.

    2013-12-01

    The use of marginal lands (MLs) for biofuel production has been contemplated as a promising solution for meeting biofuel demands. However, there have been concerns with spatial location of MLs, their inherent biofuel potential, and possible environmental consequences with the cultivation of energy crops. Here, we developed a new quantitative approach that integrates high-resolution land cover and land productivity maps and uses conditional probability density functions for analyzing land use patterns as a function of land productivity to classify the agricultural lands. We subsequently applied this method to determine available productive croplands (P-CLs) and non-crop marginal lands (NC-MLs) in a nine-county Southern Michigan. Furthermore, Spatially Explicit Integrated Modeling Framework (SEIMF) using EPIC (Environmental Policy Integrated Climate) was used to understand the net energy (NE) and soil organic carbon (SOC) implications of cultivating different annual and perennial production systems.

  15. Low temperature barriers with heat interceptor wells for in situ processes

    DOE Patents [OSTI]

    McKinzie, II, Billy John (Houston, TX)

    2008-10-14

    A system for reducing heat load applied to a frozen barrier by a heated formation is described. The system includes heat interceptor wells positioned between the heated formation and the frozen barrier. Fluid is positioned in the heat interceptor wells. Heat transfers from the formation to the fluid to reduce the heat load applied to the frozen barrier.

  16. Deseos de comunidad en el personaje intersticial y marginal: en la novela y el cine de los noventa en México

    E-Print Network [OSTI]

    Moreno, Jose Antonio

    2010-05-31

    tomar soluciones ante contextos cruciales como son los efectos de los medios de comunicación, las enfermedades pandémicas como el SIDA, la migración y la violencia. Así, el personaje intersticial-marginal proporciona en cada escena cultural una visión... aceptarse, sin caer en contradicción, que el personaje intersticial propone con sus actos deseos utópicos en tiempos que son difíciles de advertirlos. De los efectos ocasionados por el neoliberalismo económico que causaron—en toda América Latina—el peor de...

  17. Design and life-cycle considerations for unconventional-reservoir wells

    SciTech Connect (OSTI)

    Miskimins, J.L.

    2009-05-15

    This paper provides an overview of design and life-cycle considerations for certain unconventional-reservoir wells. An overview of unconventional-reservoir definitions is provided. Well design and life-cycle considerations are addressed from three aspects: upfront reservoir development, initial well completion, and well-life and long-term considerations. Upfront-reservoir-development issues discussed include well spacing, well orientation, reservoir stress orientations, and tubular metallurgy. Initial-well-completion issues include maximum treatment pressures and rates, treatment diversion, treatment staging, flowback and cleanup, and dewatering needs. Well-life and long-term discussions include liquid loading, corrosion, refracturing and associated fracture reorientation, and the cost of abandonment. These design considerations are evaluated with case studies for five unconventional-reservoir types: shale gas (Barnett shale), tight gas (Jonah feld), tight oil (Bakken play), coalbed methane (CBM) (San Juan basin), and tight heavy oil (Lost Hills field). In evaluating the life cycle and design of unconventional-reservoir wells, 'one size' does not fit all and valuable knowledge and a shortening of the learning curve can be achieved for new developments by studying similar, more-mature fields.

  18. Interpreting Horizontal Well Flow Profiles and Optimizing Well Performance by Downhole Temperature and Pressure Data 

    E-Print Network [OSTI]

    Li, Zhuoyi

    2011-02-22

    . Because of geothermal gradient, formation temperature along the depth of the wellbore changes significantly. At such a situation, some small thermal effects, such as fluid thermal expansion and viscous dissipation heating, can be ignored compared... data. For horizontal wells, because geothermal temperature changes are relatively small, the dominating effects on the wellbore temperature changes may be thermal expansion, viscous dissipative heating, and thermal conduction. Model for temperature...

  19. COMPLETION REPORT FOR WELL CLUSTER ER-5-3

    SciTech Connect (OSTI)

    BECHTEL NEVADA

    2005-12-01

    Well Cluster ER-5-3 was drilled for the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office in support of the Nevada Environmental Restoration Project at the Nevada Test Site, Nye County, Nevada. This cluster of 3 wells was drilled in 2000 and 2001 as part of a hydrogeologic investigation program in Frenchman Flat. The first borehole in the cluster, Well ER-5-3, was drilled in February and March 2000. A 47.0-centimeter surface hole was drilled and cased off to the depth of 374.8 meters. The hole diameter was decreased to 31.1 centimeters for drilling to a total depth of 794.3 meters within welded ash-flow tuff. A piezometer string with 1 slotted interval was installed in the annulus of the surface casing, open to the saturated alluvium. A completion string with 2 slotted intervals was installed in the main hole, open to saturated alluvium and to the welded tuff aquifer. A second piezometer string with 1 slotted interval open to the welded-tuff aquifer was installed outside the completion string. Well ER-5-3 No.2 was drilled about 30 meters west of the first borehole in March 2000, and was recompleted in March 2001. A 66.0-centimeter hole was drilled and cased off to the depth of 613.8 meters. The hole diameter was decreased to 44.5 centimeters and the borehole was drilled and cased off to the depth of 849.0 meters. The hole diameter was decreased once more to 31.1 centimeters for drilling to a total depth of 1,732.2 meters in dolomite. A completion string open to the dolomite (lower carbonate aquifer) was installed. Well ER-5-3 No.3 was drilled approximately 30 meters north of the first 2 boreholes in February 2001. A 66.0-centimeter hole was drilled and cased off to the depth of 36.6 meters, then the main 25.1-centimeter-diameter hole was drilled to a total depth of 548.6 meters in alluvium. A slotted stainless-steel tubing string was installed in the saturated alluvium. A preliminary composite, static water level was measured at the depth of 282.6 meters, prior to development and hydrologic testing. Detailed lithologic descriptions and stratigraphic assignments are included in the report. These are based on composite drill cuttings collected every 3 meters, and 120 sidewall samples taken at various depths below 91 meters in Wells ER-5-3 and ER-5-3 No.2, supplemented by geophysical log data. The wells penetrated Quaternary/Tertiary alluvium to the depth of 622.4 meters, and an 8.5-meter-thick basalt flow was encountered within the alluvium. Tertiary tuff was penetrated to the depth of approximately 1,425.9 meters, where the top of the lower carbonate aquifer was tagged in Well ER-5-3 No.2.

  20. Recomplete deep hot wells successfully with coiled tubing

    SciTech Connect (OSTI)

    Garner, T.; Fleckenstein, W.; Shelley, B.

    1995-06-01

    A squeeze reperforation procedure in the Elk Hills, California field using coiled tubing included contaminating excess cement and jetting it from the well bore to eliminate the need to drill out cement before shooting new perforations. The 324-7R well was producing 260 b/d of oil through 2 7/8-in. production tubing, with a 20,000-scf/bbl gas-oil ratio (GOR). Bottomhole static temperature was 250 F. After pumping a cement squeeze to 9,000 ft trough 1{1/2}-in. coiled tubing (CT) run inside the production tubing, oil production increased to 550 b/d of oil, and the GOR decreased to 5,000 scf/bbl when new perforations were shot. Cement was pumped 9,000 ft through the CT and circulated back through the production tubing/CT annulus. Operation cost was estimated at 20% less than for a comparable job performance with conventional tubing. Cost of the CT squeeze was recovered by 58 days incremental production.

  1. Methods of producing adsorption media including a metal oxide

    DOE Patents [OSTI]

    Mann, Nicholas R; Tranter, Troy J

    2014-03-04

    Methods of producing a metal oxide are disclosed. The method comprises dissolving a metal salt in a reaction solvent to form a metal salt/reaction solvent solution. The metal salt is converted to a metal oxide and a caustic solution is added to the metal oxide/reaction solvent solution to adjust the pH of the metal oxide/reaction solvent solution to less than approximately 7.0. The metal oxide is precipitated and recovered. A method of producing adsorption media including the metal oxide is also disclosed, as is a precursor of an active component including particles of a metal oxide.

  2. Thin film solar cell including a spatially modulated intrinsic layer

    DOE Patents [OSTI]

    Guha, Subhendu (Troy, MI); Yang, Chi-Chung (Troy, MI); Ovshinsky, Stanford R. (Bloomfield Hills, MI)

    1989-03-28

    One or more thin film solar cells in which the intrinsic layer of substantially amorphous semiconductor alloy material thereof includes at least a first band gap portion and a narrower band gap portion. The band gap of the intrinsic layer is spatially graded through a portion of the bulk thickness, said graded portion including a region removed from the intrinsic layer-dopant layer interfaces. The band gap of the intrinsic layer is always less than the band gap of the doped layers. The gradation of the intrinsic layer is effected such that the open circuit voltage and/or the fill factor of the one or plural solar cell structure is enhanced.

  3. Solar Energy Education. Renewable energy: a background text. [Includes glossary

    SciTech Connect (OSTI)

    Not Available

    1985-01-01

    Some of the most common forms of renewable energy are presented in this textbook for students. The topics include solar energy, wind power hydroelectric power, biomass ocean thermal energy, and tidal and geothermal energy. The main emphasis of the text is on the sun and the solar energy that it yields. Discussions on the sun's composition and the relationship between the earth, sun and atmosphere are provided. Insolation, active and passive solar systems, and solar collectors are the subtopics included under solar energy. (BCS)

  4. A model of the methane cycle, permafrost, and hydrology of the Siberian continental margin

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Archer, D.

    2014-06-03

    A two-dimensional model of a passive continental margin was adapted to the simulation of the methane cycle on Siberian continental shelf and slope, attempting to account for the impacts of glacial/interglacial cycles in sea level, alternately exposing the continental shelf to freezing conditions with deep permafrost formation during glacial times, and immersion in the ocean in interglacial times. The model is used to gauge the impact of the glacial cycles, and potential anthropogenic warming in the deep future, on the atmospheric methane emission flux, and the sensitivities of that flux to processes such as permafrost formation and terrestrial organic carbonmore »(Yedoma) deposition. Hydrological forcing drives a freshening and ventilation of pore waters in areas exposed to the atmosphere, which is not quickly reversed by invasion of seawater upon submergence, since there is no analogous saltwater pump. This hydrological pump changes the salinity enough to affect the stability of permafrost and methane hydrates on the shelf. Permafrost formation inhibits bubble transport through the sediment column, by construction in the model. The impact of permafrost on the methane budget is to replace the bubble flux by offshore groundwater flow containing dissolved methane, rather than accumulating methane for catastrophic release when the permafrost seal fails during warming. By far the largest impact of the glacial/interglacial cycles on the atmospheric methane flux is attenuation by dissolution of bubbles in the ocean when sea level is high. Methane emissions are highest during the regression (soil freezing) part of the cycle, rather than during transgression (thawing). The model-predicted methane flux to the atmosphere in response to a warming climate is small, relative to the global methane production rate, because of the ongoing flooding of the continental shelf. A slight increase due to warming could be completely counteracted by sea level rise on geologic time scales, decreasing the efficiency of bubble transit through the water column. The methane cycle on the shelf responds to climate change on a long time constant of thousands of years, because hydrate is excluded thermodynamically from the permafrost zone by water limitation, leaving the hydrate stability zone at least 300 m below the sediment surface.« less

  5. MNSR transient analyses and thermal hydraulic safety margins for HEU and LEU cores using the RELAP5-3D code

    SciTech Connect (OSTI)

    Dunn, F.E.; Thomas, J.; Liaw, J.; Matos, J.E. [RERTR Program, Argonne National Laboratory, Argonne, IL 60439 (United States)

    2008-07-15

    For safety analyses to support conversion of MNSR reactors from HEU fuel to LEU fuel, a RELAP5-3D model was set up to simulate the entire MNSR system. This model includes the core, the beryllium reflectors, the water in the tank and the water in the surrounding pool. The MCNP code was used to obtain the power distributions in the core and to obtain reactivity feedback coefficients for the transient analyses. The RELAP5-3D model was validated by comparing measured and calculated data for the NIRR-1 reactor in Nigeria. Comparisons include normal operation at constant power and a 3.77 mk rod withdrawal transient. Excellent agreement was obtained for core coolant inlet and outlet temperatures for operation at constant power, and for power level, coolant inlet temperature, and coolant outlet temperature for the rod withdrawal transient. In addition to the negative reactivity feedbacks from increasing core moderator and fuel temperatures, it was necessary to calculate and include positive reactivity feedback from temperature changes in the radial beryllium reflector and changes in the temperature and density of the water in the tank above the core and at the side of the core. The validated RELAP5-3D model was then used to analyze 3.77 mk rod withdrawal transients for LEU cores with two UO{sub 2} fuel pin designs. The impact of cracking of oxide LEU fuel is discussed. In addition, steady-state power operation at elevated power levels was evaluated to determine steady-state safety margins for onset of nucleate boiling and for onset of significant voiding. (author)

  6. Biomass Potentials from California Forest and Shrublands Including Fuel

    E-Print Network [OSTI]

    Biomass Potentials from California Forest and Shrublands Including Fuel Reduction Potentials-04-004 February 2005 Revised: October 2005 Arnold Schwarzenegger, Governor, State of California #12;Biomass Tiangco, CEC Bryan M. Jenkins, University of California #12;Biomass Potentials from California Forest

  7. Applied Linguistics Department Curriculum for the IEP Including Curriculum Summary

    E-Print Network [OSTI]

    Weaver, Adam Lee

    Applied Linguistics Department Curriculum for the IEP Including Curriculum Summary 1 C-1-2 Curriculum for the IEP (as described in CEA Curriculum Standards) I. General Curriculum Philosophy a topics, and global issues. b. Skills Development: The IEP curriculum offers courses that provide skills

  8. Optimal Energy Management Strategy including Battery Health through Thermal

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Optimal Energy Management Strategy including Battery Health through Thermal Management for Hybrid: Energy management strategy, Plug-in hybrid electric vehicles, Li-ion battery aging, thermal management, Pontryagin's Minimum Principle. 1. INTRODUCTION The interest for energy management strategy (EMS) of Hybrid

  9. Directing all emergency activities including evacuation of personnel.

    E-Print Network [OSTI]

    Johnson, Eric E.

    for employees who perform or shut down critical plant operations. · Systems to account for all employees after· Directing all emergency activities including evacuation of personnel. · Ensuring that outside emergency services are notified when necessary. · Directing the shutdown of plant operations when necessary

  10. Thermal Unit Commitment Including Optimal AC Power Flow Constraints

    E-Print Network [OSTI]

    Thermal Unit Commitment Including Optimal AC Power Flow Constraints Carlos Murillo{Sanchez Robert J algorithm for unit commitment that employs a Lagrange relaxation technique with a new augmentation. This framework allows the possibility of committing units that are required for the VArs that they can produce

  11. cDNA encoding a polypeptide including a hevein sequence

    DOE Patents [OSTI]

    Raikhel, N.V.; Broekaert, W.F.; Namhai Chua; Kush, A.

    1993-02-16

    A cDNA clone (HEV1) encoding hevein was isolated via polymerase chain reaction (PCR) using mixed oligonucleotides corresponding to two regions of hevein as primers and a Hevea brasiliensis latex cDNA library as a template. HEV1 is 1,018 nucleotides long and includes an open reading frame of 204 amino acids.

  12. Major initiatives in materials research at Western include

    E-Print Network [OSTI]

    Christensen, Dan

    , and the growth and formation of new materials. Western is a leader in the study of the interactions of radiationMajor initiatives in materials research at Western include Surface Science Western, Interface of the wide range of materials and biomaterials research within the Faculty of Science and across Western

  13. Assessment of Mission Design Including Utilization of Libration

    E-Print Network [OSTI]

    Barcelona, Universitat de

    Assessment of Mission Design Including Utilization of Libration Points and Weak Stability: The International Sun-Earth Explorer 3 . . . . . . . . . . . . . . . 11 2.1.2 WIND/JWST: Next Generation Space Telescope . . . . . . . . . . . . . . . 33 2.1.9 FIRST/HERSCHEL: Far Infra

  14. Free Energy Efficiency Kit includes CFL light bulbs,

    E-Print Network [OSTI]

    Rose, Annkatrin

    Free Energy Efficiency Kit Kit includes CFL light bulbs, spray foam, low-flow shower head, and more for discounted energy assessments. FREE HOME ENERGY EFFICIENCY SEMINAR N e w R i ver L i g ht & Pow e r a n d W! Building Science 101 Presentation BPI Certified Building Professionals will present home energy efficiency

  15. Introduction Adhesion complexes play key roles in many events, including

    E-Print Network [OSTI]

    Hardin, Jeff

    Introduction Adhesion complexes play key roles in many events, including cell migration cell adhesion are remarkably similar in Caenorhabditis elegans, Drosophila and humans (Hynes and Zhao to reveal much about the basic, conserved molecular mechanisms that mediate and regulate cell adhesion

  16. Primary Cementing of a Highly Deviated Oil Well

    E-Print Network [OSTI]

    Fournier, John J.F.

    in the construction of a well. The objective is to provide zonal isolation, i.e., a hydraulic seal between the wellPrimary Cementing of a Highly Deviated Oil Well by Mariana Carrasco-Teja B.Sc., Instituto Tecnol. The study comes from the primary cementing of highly deviated oil and gas wells. Highly deviated wells

  17. The Effect of Well Trajectory on Production Performance of Tight Gas Wells 

    E-Print Network [OSTI]

    Aldousari, Mohammad

    2012-02-14

    are for incompressible or slightly compressible single-phase liquid; however, they can be extended to other fluid types. 3 Beggs-Brill correlation is one of the most commonly used models to calculate pressure drop in horizontal pipe. It was developed from... (Beggs and Brill, 1973). Xiao model is a comprehensive mechanistic model developed for gas-liquid two phase flow in horizontal and near horizontal pipelines. It has been evaluated against a data bank that includes field data, and laboratory data...

  18. 2013 Idaho National Laboratory Water Use Report and Comprehensive Well Inventory (Revision 22)

    SciTech Connect (OSTI)

    Mike Lewis

    2014-06-01

    This 2013 Idaho National Laboratory Water Use Report and Comprehensive Well Inventory (Revision 22) provides water use information for production and potable water wells at the Idaho National Laboratory for Calendar Year 2013. It also provides detailed information for new, modified, and decommissioned wells and holes. Two new wells were drilled and completed in Calendar Year 2013. No modifications were performed on any wells. Seven wells were decommissioned in Calendar Year 2013. Detailed construction information for the new and decommissioned wells is provided. Location maps are included, provided survey information was available. This report is being submitted in accordance with the Water Rights Agreement between the State of Idaho and the United States, for the United States Department of Energy (dated 1990) and the subsequent Partial Decree for Water Right 34-10901 issued June 20, 2003.

  19. U.S. Average Depth of Crude Oil Exploratory Wells Drilled (Feet per Well)

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustments (BillionProved Reserves (Billion Cubic Feet)Estimated Production fromSales (Billion CubicWells

  20. U.S. Average Depth of Natural Gas Exploratory Wells Drilled (Feet per Well)

    Annual Energy Outlook [U.S. Energy Information Administration (EIA)]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Homesum_a_epg0_fpd_mmcf_m.xls" ,"Available from WebQuantity of Natural GasAdjustments (BillionProved Reserves (Billion Cubic Feet)Estimated Production fromSalesWells Drilled (Feet per

  1. Economic viability of multiple-lateral horizontal wells 

    E-Print Network [OSTI]

    Smith, Christopher Jason

    1995-01-01

    Horizontal wells are gaining popularity throughout the petroleum industry as a means to increase well productivity and enhance incremental economics. Horizontal wells provide greater reservoir exposure and are useful in ...

  2. UTM Well Coordinates for the Boise Hydrogeophysical Research Site (BHRS)

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    David Lim

    2014-12-19

    A series of oscillatory pumping tests were performed at the BHRS. The data collected from these wells will be used to tomographically image the shallow subsurface. This excel file only contains well coordinates for all wells at the Boise site.

  3. UTM Well Coordinates for the Boise Hydrogeophysical Research Site (BHRS)

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    David Lim

    A series of oscillatory pumping tests were performed at the BHRS. The data collected from these wells will be used to tomographically image the shallow subsurface. This excel file only contains well coordinates for all wells at the Boise site.

  4. Identifying Infill Locations and Underperformer Wells in Mature Fields using

    E-Print Network [OSTI]

    Mohaghegh, Shahab

    field. Identify opportunities in mature fields: Sweet spots for infill drilling. Underperformer wellsIdentifying Infill Locations and Underperformer Wells in Mature Fields using Monthly Production wells rather than the entire field. #12;Introduction Objective Methodology Results Conclusion Objective

  5. Modeling performance of horizontal, undulating, and multilateral wells 

    E-Print Network [OSTI]

    Kamkom, Rungtip

    2009-05-15

    Horizontal, undulating, and multilateral wells are relatively new alternatives in field development because they can increase the productivity per well and reduce the cost of field development. Because the feasibility of these wells may not be valid...

  6. Understanding the Participation of Marginal Groups in Annapurna Conservation Area, Nepal 

    E-Print Network [OSTI]

    Dahal, Smriti

    2012-02-14

    Participation has been promoted and studied in diverse disciplines including tourism, development, planning, health, politics, and others. In natural resource conservation, the shift from centralized to decentralized decision making which emphasizes...

  7. The Effect of Digital Die Spacer on the Marginal Fit of Cad Pressed Lithium Disilicate Complete Coverage Copings: An SEM Assessment 

    E-Print Network [OSTI]

    Fischer, James

    2015-04-24

    The purpose of this in vitro study was to evaluate the marginal fit of pressed IPS e.max copings fabricated from a computer-aided designed and milled PMMA acrylic resin burnout coping of various cement spacer thicknesses. ...

  8. Well Log Data At Valles Caldera - Redondo Geothermal Area (Shevenell...

    Open Energy Info (EERE)

    Well Log Data At Valles Caldera - Redondo Geothermal Area (Shevenell, Et Al., 1988) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Well Log Data...

  9. Exploratory Well At Long Valley Caldera Geothermal Area (Smith...

    Open Energy Info (EERE)

    Exploratory Well At Long Valley Caldera Geothermal Area (Smith & Rex, 1977) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Exploratory Well At...

  10. Well Log Data At Blue Mountain Geothermal Area (Fairbank & Niggemann...

    Open Energy Info (EERE)

    Well Log Data At Blue Mountain Geothermal Area (Fairbank & Niggemann, 2004) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Well Log Data At Blue...

  11. Conversion of geothermal waste to commercial products including silica

    DOE Patents [OSTI]

    Premuzic, Eugene T. (East Moriches, NY); Lin, Mow S. (Rocky Point, NY)

    2003-01-01

    A process for the treatment of geothermal residue includes contacting the pigmented amorphous silica-containing component with a depigmenting reagent one or more times to depigment the silica and produce a mixture containing depigmented amorphous silica and depigmenting reagent containing pigment material; separating the depigmented amorphous silica and from the depigmenting reagent to yield depigmented amorphous silica. Before or after the depigmenting contacting, the geothermal residue or depigmented silica can be treated with a metal solubilizing agent to produce another mixture containing pigmented or unpigmented amorphous silica-containing component and a solubilized metal-containing component; separating these components from each other to produce an amorphous silica product substantially devoid of metals and at least partially devoid of pigment. The amorphous silica product can be neutralized and thereafter dried at a temperature from about 25.degree. C. to 300.degree. C. The morphology of the silica product can be varied through the process conditions including sequence contacting steps, pH of depigmenting reagent, neutralization and drying conditions to tailor the amorphous silica for commercial use in products including filler for paint, paper, rubber and polymers, and chromatographic material.

  12. SU-E-J-88: Margin Reduction of Level II/III Planning Target Volume for Image-Guided Simultaneous Integrated Boost Head-And-Neck Treatment

    SciTech Connect (OSTI)

    Can, S; Neylon, J; Qi, S; Santhanam, A; Low, D

    2014-06-01

    Purpose: To investigate the feasibility of improved normal tissue sparing for head-and-neck (H'N) image-guided radiotherapy (IGRT) by employing tighter CTV-to-PTV margins for target level II/III though a GPU-based deformable image registration and dose accumulation framework. Methods: Ten H'N simultaneous integrated boost cases treated on TomoTherapy were retrospectively analyzed. Weekly kVCT scans in addition to daily MVCT scans were acquired for each patient. Reduced margin plans were generated with 0- mm margin for level II and III PTV (while 3-5 mm margin for PTV1) and compared with the standard margin plan using 3-5mm margin to all CTV1-3 (reference plan). An in-house developed GPU-based 3D image deformation tool was used to register and deform the weekly KVCTs with the planning CT and determine the delivered mean/minimum/maximum dose, dose volume histograms (DVHs), etc. Results: Compared with the reference plans, the averaged cord maximum, the right and left parotid doses reduced by 22.7 %, 16.5 %, and 9 % respectively in the reduced margin plans. The V95 for PTV2 and PTV3 were found within 2 and 5% between the reference and tighter margin plans. For the reduced margin plans, the averaged cumulative mean doses were consistent with the planned dose for PTV1, PTV2 and PTV3 within 1.5%, 1.7% and 1.4%. Similar dose variations of the delivered dose were seen for the reference and tighter margin plans. The delivered maximum and mean doses for the cord were 3.55 % and 2.37% higher than the planned doses; a 5 % higher cumulative mean dose for the parotids was also observed for the delivered dose than the planned doses in both plans. Conclusion: By imposing tighter CTV-to-PTV margins for level II and III targets for H'N irradiation, acceptable cumulative doses were achievable when coupled with weekly kVCT guidance while improving normal structure sparing.

  13. Selection of area and specific site for drilling a horizontal well in Calhoun County, West Virginia

    SciTech Connect (OSTI)

    Reeves, T.K.; Overbey, W.K. Jr.; Salamy, S.P.; Locke, C.D.

    1992-03-01

    This report discusses the data collection and analysis procedures used to establish criteria for geologic and engineering studies conducted by BDM to select a general area for more detailed study and a specific site for the drilling of a cooperative well with an industry partner, the Consolidated Natural Gas Development Company (CNGD). The results of detailed geologic studies are presented for two areas in Calhoun County, West Virginia, and one area along the Logan-Boone County line in West Virginia. The effects of Appalachian Basin tectonics and the Rome Trough Rift system were identified on seismic lines made available by (CNGD). These helped to identify and define the trapping mechanisms which had been effective in each area. Engineering analyses of past production histories provided data to support selection of target areas and then to select a specific site that met the project requirements for production, reservoir pressure, and risk. A final site was selected in Lee District at the southwestern margin of the Sand Ridge gas field based on the combination of a geologic trapping mechanism and reservoir pressures which were projected as 580 psi with a stress ratio of 0.53.

  14. Analysis and correlation of volcanic ash in marine sediments from the Peru Margin, Ocean Drilling Program Leg 201: explosive volcanic cycles of the north-central Andes 

    E-Print Network [OSTI]

    Hart, Shirley Dawn

    2007-04-25

    -1 ANALYSIS AND CORRELATION OF VOLCANIC ASH IN MARINE SEDIMENTS FROM THE PERU MARGIN, OCEAN DRILLING PROGRAM LEG 201: EXPLOSIVE VOLCANIC CYCLES OF THE NORTH-CENTRAL ANDES A Thesis by SHIRLEY DAWN HART Submitted to the Office of Graduate Studies... MARGIN, OCEAN DRILLING PROGRAM LEG 201: EXPLOSIVE VOLCANIC CYCLES OF THE NORTH-CENTRAL ANDES A Thesis by SHIRLEY DAWN HART Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment of the requirements...

  15. Efficiently log and perforate 60 + wells with coiled tubing

    SciTech Connect (OSTI)

    Fertl, W.H.; Hotz, R.F.

    1987-07-01

    In today's petroleum industry, more and more emphasis is being placed on logging and completion techniques for highly deviated (extended-reach) and horizontal boreholes. This is the result of cost-effective development of oil and gas via: a minimum number of production platforms on large structures, incremental but marginal reserves in outlying and/or small fault blocks, shallow reservoirs in deep offshore waters, and significant hydrocarbon accumulations in environmentally sensitive and/or restrictive areas, e.g., perma-frost, urban areas, etc. The major challenge in logging such high-angle, extended-reach, and also horizontal boreholes is guiding the logging tool string to the bottom of the wellbore. In the horizontal portion of a borehole, the use of coiled tubing has proven successful in ''pushing'' the logging instrumentation toward the bottom (end) of the borehole.

  16. Page 8 MARGINS Newsletter No. 3 What makes the largest faults, the ones

    E-Print Network [OSTI]

    Taylor, Brian

    if unusually weak or well lubricated. Leg 180 established a high-resolution syn- rift stratigraphy, vertical that are its fossil counterparts. Earthquake source parameters and seismic reflection data indicate that normal of the most seismically active rift systems on Earth (Fig. 1). Current rifting and spreading are confirmed

  17. Evaluation of Travis Peak gas reservoirs, west margin of the East Texas Basin 

    E-Print Network [OSTI]

    Li, Yamin

    2009-05-15

    produced gas since the 1940s. In this study, well log, 2D seismic, core, and production data were used to evaluate the geologic setting and reservoir characteristics of the Travis Peak formation. The primary objective was to assess the potential...

  18. Optimising Market Share and Profit Margin: SMDP-based Tariff Pricing under the Smart Grid

    E-Print Network [OSTI]

    Chli, Maria

    market dynamisms.1 Power TAC simulates an open and competitive electricity wholesale and retail market market, an energy retailer aims to simultaneously increase the number of contracted customers and its the competition, AstonTAC was the only retailer agent performing well across all retail market settings. I

  19. Cryopreservation of carotid artery segments via vitrification subject to marginal thermal conditions: Correlation of freezing visualization

    E-Print Network [OSTI]

    Rabin, Yoed

    Available online 28 March 2008 Keywords: Vitrification Functional recovery Blood vessels Cryomacroscopy is a well-established technique for long-term storage of viable cells and tissues. How- ever, in recent testing on a contractility apparatus by measuring isometric responses to four agonist and antagonists

  20. Composite armor, armor system and vehicle including armor system

    DOE Patents [OSTI]

    Chu, Henry S.; Jones, Warren F.; Lacy, Jeffrey M.; Thinnes, Gary L.

    2013-01-01

    Composite armor panels are disclosed. Each panel comprises a plurality of functional layers comprising at least an outermost layer, an intermediate layer and a base layer. An armor system incorporating armor panels is also disclosed. Armor panels are mounted on carriages movably secured to adjacent rails of a rail system. Each panel may be moved on its associated rail and into partially overlapping relationship with another panel on an adjacent rail for protection against incoming ordnance from various directions. The rail system may be configured as at least a part of a ring, and be disposed about a hatch on a vehicle. Vehicles including an armor system are also disclosed.

  1. cDNA encoding a polypeptide including a hevein sequence

    DOE Patents [OSTI]

    Raikhel, Natasha V. (Okemos, MI); Broekaert, Willem F. (Dilbeek, BE); Chua, Nam-Hai (Scarsdale, NY); Kush, Anil (New York, NY)

    1993-02-16

    A cDNA clone (HEV1) encoding hevein was isolated via polymerase chain reaction (PCR) using mixed oligonucleotides corresponding to two regions of hevein as primers and a Hevea brasiliensis latex cDNA library as a template. HEV1 is 1018 nucleotides long and includes an open reading frame of 204 amino acids. The deduced amino acid sequence contains a pu GOVERNMENT RIGHTS This application was funded under Department of Energy Contract DE-AC02-76ER01338. The U.S. Government has certain rights under this application and any patent issuing thereon.

  2. Composite material including nanocrystals and methods of making

    DOE Patents [OSTI]

    Bawendi, Moungi G.; Sundar, Vikram C.

    2010-04-06

    Temperature-sensing compositions can include an inorganic material, such as a semiconductor nanocrystal. The nanocrystal can be a dependable and accurate indicator of temperature. The intensity of emission of the nanocrystal varies with temperature and can be highly sensitive to surface temperature. The nanocrystals can be processed with a binder to form a matrix, which can be varied by altering the chemical nature of the surface of the nanocrystal. A nanocrystal with a compatibilizing outer layer can be incorporated into a coating formulation and retain its temperature sensitive emissive properties.

  3. Composite material including nanocrystals and methods of making

    DOE Patents [OSTI]

    Bawendi, Moungi G. (Boston, MA); Sundar, Vikram C. (New York, NY)

    2008-02-05

    Temperature-sensing compositions can include an inorganic material, such as a semiconductor nanocrystal. The nanocrystal can be a dependable and accurate indicator of temperature. The intensity of emission of the nanocrystal varies with temperature and can be highly sensitive to surface temperature. The nanocrystals can be processed with a binder to form a matrix, which can be varied by altering the chemical nature of the surface of the nanocrystal. A nanocrystal with a compatibilizing outer layer can be incorporated into a coating formulation and retain its temperature sensitive emissive properties

  4. MONITORING WELL-BEING OF CIVIL ENGINEERING PROFESSION

    E-Print Network [OSTI]

    Bruneau, Michel

    MONITORING WELL-BEING OF CIVIL ENGINEERING PROFESSION By Michel Bruneau, 1Member, ASCE ABSTRACT reported decline in the well-beingof the civilengineering profession. These deficienciesare: (1) Public-beingof the civilengineering profession, as well as the evolution of this well-being.Quan- titativeperformanceindicesare

  5. Well completion process for formations with unconsolidated sands

    DOE Patents [OSTI]

    Davies, David K. (Kingwood, TX); Mondragon, III, Julius J. (Redondo Beach, CA); Hara, Philip Scott (Monterey Park, CA)

    2003-04-29

    A method for consolidating sand around a well, involving injecting hot water or steam through well casing perforations in to create a cement-like area around the perforation of sufficient rigidity to prevent sand from flowing into and obstructing the well. The cement area has several wormholes that provide fluid passageways between the well and the formation, while still inhibiting sand inflow.

  6. Sedimentary and faunal analysis of a marginal marine section, the Stone City Member (middle eocene), Crockett Formation, Burleson County, Texas 

    E-Print Network [OSTI]

    Nelms, Katherine Currier

    1979-01-01

    Diagram relating Miliolina-Rotaliina-Textulariina abundance to deltaic and other marginal marine environments 98 LIST OF FIGURES - Cont1nued F1 gure 15 Ratio of Textulari1na-Rotaliina-Nil1olina in samples from the Stone C1ty beds 16 Vertical... sediment packages and faunal assemblages may still be recognized. W. L. F1sher (1964) describes transgressive and regressive sediments from the Eocene of the Gulf Coast and characterizes dist1nctive groups of sediments which tend to occur in typical...

  7. Philip Henry Wicksteed's marginal productivity theory of distribution and an investigation of those factors which influenced its formulation 

    E-Print Network [OSTI]

    Garner, Joseph Key

    1970-01-01

    their impoverished state. From these forces Hicksteed conceived the idea of a Labour Church that. would be dedicated to the working man and be the core of his religious activity. The Labour Church only enjoyed a short popularity. From Jevons, Hic'ksteed found... to the development oZ the marginal productivity theory of distribution and those factors that influenced its formulation, but berore turning to these topics, it is necessary to digress into two related discussions. First, a brief sketch will be made of Wicksteed...

  8. A study of beef cattle marketing in Venezuela and the marketing margins between the farm and retail levels of prices 

    E-Print Network [OSTI]

    Acosta, Sady Ines Borjas-Paez

    1975-01-01

    partial fulf i 1 lment of the recu'. rement i or rhe degree of MASTEF, OF SCIENCE December 1975 Major Subject: Agricultural Economics A STUDY OF B EF' CATTLE M. 'RKEl'lNG :N VENEZUELA AND THE MARKETING MAPGINS BETWEEN THE FVARM AND RETAIL LEVELS Ot... for the period 1960-1972 were studied from the farm through 'retail levels, the variations in price spread were large. Lack of knowledge concerning share of marketing margins has brought inadequate govern- ment policies. The structural demand equation...

  9. Economic Impacts of Changes in United States Rice Price Variability on Market Efficiency, Marketing Margin and Producer Viability. 

    E-Print Network [OSTI]

    Grant, W.R.; Richardson, J.W.; Brorsen, B.W.; Rister, M.E

    1984-01-01

    Station , Texas (Blank P~le fa 0rigiIlat BuDetiDJ "/ ' k ? Econolllic Illlpacts of Changes in United States Rice Price Variability on Market Efficiency, Marketing Margin, and Producer Viability W. R. GRANT, agricultural economist National... recorded. The sharp rise in prices triggered a suspension of domestic marketing quotas for P R I C E DOL/CWT 32.5 - 30.0 - 27.5 25.0 - 22.5 - 20.0 - 17.5 - 15.0 - 12.5 - 10.0 - 7.5 - Texas Mill Thailand Mill , , , , , , the 1974...

  10. Community Assessment Tool for Public Health Emergencies Including Pandemic Influenza

    SciTech Connect (OSTI)

    ORAU's Oak Ridge Institute for Science Education (HCTT-CHE)

    2011-04-14

    The Community Assessment Tool (CAT) for Public Health Emergencies Including Pandemic Influenza (hereafter referred to as the CAT) was developed as a result of feedback received from several communities. These communities participated in workshops focused on influenza pandemic planning and response. The 2008 through 2011 workshops were sponsored by the Centers for Disease Control and Prevention (CDC). Feedback during those workshops indicated the need for a tool that a community can use to assess its readiness for a disaster - readiness from a total healthcare perspective, not just hospitals, but the whole healthcare system. The CAT intends to do just that - help strengthen existing preparedness plans by allowing the healthcare system and other agencies to work together during an influenza pandemic. It helps reveal each core agency partners (sectors) capabilities and resources, and highlights cases of the same vendors being used for resource supplies (e.g., personal protective equipment [PPE] and oxygen) by the partners (e.g., public health departments, clinics, or hospitals). The CAT also addresses gaps in the community's capabilities or potential shortages in resources. This tool has been reviewed by a variety of key subject matter experts from federal, state, and local agencies and organizations. It also has been piloted with various communities that consist of different population sizes, to include large urban to small rural communities.

  11. Laser Oil and Gas Well Drilling Demonstration Videos

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    ANL's Laser Applications Laboratory and collaborators are examining the feasibility of adapting high-power laser technology to drilling for gas and oil. The initial phase is designed to establish a scientific basis for developing a commercial laser drilling system and determine the level of gas industry interest in pursuing future research. Using lasers to bore a hole offers an entirely new approach to mechanical drilling. The novel drilling system would transfer light energy from lasers on the surface, down a borehole by a fiber optic bundle, to a series of lenses that would direct the laser light to the rock face. Researchers believe that state-of-the-art lasers have the potential to penetrate rock many times faster than conventional boring technologies - a huge benefit in reducing the high costs of operating a drill rig. Because the laser head does not contact the rock, there is no need to stop drilling to replace a mechanical bit. Moreover, researchers believe that lasers have the ability to melt the rock in a way that creates a ceramic sheath in the wellbore, eliminating the expense of buying and setting steel well casing. A laser system could also contain a variety of downhole sensors, including visual imaging systems that could communicate with the surface through the fiber optic cabling. Earlier studies have been promising, but there is still much to learn. One of the primary objectives of the new study will be to obtain much more precise measurements of the energy requirements needed to transmit light from surface lasers down a borehole with enough power to bore through rocks as much as 20,000 feet or more below the surface. Another objective will be to determine if sending the laser light in sharp pulses, rather than as a continuous stream, could further increase the rate of rock penetration. A third aspect will be to determine if lasers can be used in the presence of drilling fluids. In most wells, thick fluids called "drilling muds" are injected into the borehole to wash out rock cuttings and keep water and other fluids from the underground formations from seeping into the well. The technical challenge will be to determine whether too much laser energy is expended to clear away the fluid where the drilling is occurring. (Copied with editing from http://www.ne.anl.gov/facilities/lal/laser_drilling.html). The demonstration videos, provided here in QuickTime format, are accompanied by patent documents and PDF reports that, together, provide an overall picture of this fascinating project.

  12. The continental shelf and upper slope of the Oregon Cascadia margin are underlain by an

    E-Print Network [OSTI]

    Goldfinger, Chris

    stratigraphy includes a regional late Miocene unconformity that may coincide with a worldwide hiatus ca. 7 and correlated seaward reflec- tor from seismic reflection data clearly out- lines deformation into major mar- gin. The basin stratigraphy contains several re- gional unconformities, suggesting a complex his

  13. Electra-optical device including a nitrogen containing electrolyte

    DOE Patents [OSTI]

    Bates, J.B.; Dudney, N.J.; Gruzalski, G.R.; Luck, C.F.

    1995-10-03

    Described is a thin-film battery, especially a thin-film microbattery, and a method for making same having application as a backup or primary integrated power source for electronic devices. The battery includes a novel electrolyte which is electrochemically stable and does not react with the lithium anode and a novel vanadium oxide cathode. Configured as a microbattery, the battery can be fabricated directly onto a semiconductor chip, onto the semiconductor die or onto any portion of the chip carrier. The battery can be fabricated to any specified size or shape to meet the requirements of a particular application. The battery is fabricated of solid state materials and is capable of operation between {minus}15 C and 150 C.

  14. Protoplanetary disks including radiative feedback from accreting planets

    E-Print Network [OSTI]

    Montesinos, Matias; Perez, Sebastian; Baruteau, Clement; Casassus, Simon

    2015-01-01

    While recent observational progress is converging on the detection of compact regions of thermal emission due to embedded protoplanets, further theoretical predictions are needed to understand the response of a protoplanetary disk to the planet formation radiative feedback. This is particularly important to make predictions for the observability of circumplanetary regions. In this work we use 2D hydrodynamical simulations to examine the evolution of a viscous protoplanetary disk in which a luminous Jupiter-mass planet is embedded. We use an energy equation which includes the radiative heating of the planet as an additional mechanism for planet formation feedback. Several models are computed for planet luminosities ranging from $10^{-5}$ to $10^{-3}$ Solar luminosities. We find that the planet radiative feedback enhances the disk's accretion rate at the planet's orbital radius, producing a hotter and more luminous environement around the planet, independently of the prescription used to model the disk's turbul...

  15. Including stereoscopic information in the reconstruction of coronal magnetic fields

    E-Print Network [OSTI]

    T. Wiegelmann; T. Neukirch

    2008-01-23

    We present a method to include stereoscopic information about the three dimensional structure of flux tubes into the reconstruction of the coronal magnetic field. Due to the low plasma beta in the corona we can assume a force free magnetic field, with the current density parallel to the magnetic field lines. Here we use linear force free fields for simplicity. The method uses the line of sight magnetic field on the photosphere as observational input. The value of $\\alpha$ is determined iteratively by comparing the reconstructed magnetic field with the observed structures. The final configuration is the optimal linear force solution constrained by both the photospheric magnetogram and the observed plasma structures. As an example we apply our method to SOHO MDI/EIT data of an active region. In the future it is planned to apply the method to analyse data from the SECCHI instrument aboard the STEREO mission.

  16. Electra-optical device including a nitrogen containing electrolyte

    DOE Patents [OSTI]

    Bates, John B. (Oak Ridge, TN); Dudney, Nancy J. (Knoxville, TN); Gruzalski, Greg R. (Oak Ridge, TN); Luck, Christopher F. (Knoxville, TN)

    1995-01-01

    Described is a thin-film battery, especially a thin-film microbattery, and a method for making same having application as a backup or primary integrated power source for electronic devices. The battery includes a novel electrolyte which is electrochemically stable and does not react with the lithium anode and a novel vanadium oxide cathode Configured as a microbattery, the battery can be fabricated directly onto a semiconductor chip, onto the semiconductor die or onto any portion of the chip carrier. The battery can be fabricated to any specified size or shape to meet the requirements of a particular application. The battery is fabricated of solid state materials and is capable of operation between -15.degree. C. and 150.degree. C.

  17. Copper laser modulator driving assembly including a magnetic compression laser

    DOE Patents [OSTI]

    Cook, Edward G. (Livermore, CA); Birx, Daniel L. (Oakley, CA); Ball, Don G. (Livermore, CA)

    1994-01-01

    A laser modulator (10) having a low voltage assembly (12) with a plurality of low voltage modules (14) with first stage magnetic compression circuits (20) and magnetic assist inductors (28) with a common core (91), such that timing of the first stage magnetic switches (30b) is thereby synchronized. A bipolar second stage of magnetic compression (42) is coupled to the low voltage modules (14) through a bipolar pulse transformer (36) and a third stage of magnetic compression (44) is directly coupled to the second stage of magnetic compression (42). The low voltage assembly (12) includes pressurized boxes (117) for improving voltage standoff between the primary winding assemblies (34) and secondary winding (40) contained therein.

  18. Pulse transmission transmitter including a higher order time derivate filter

    DOE Patents [OSTI]

    Dress, Jr., William B.; Smith, Stephen F.

    2003-09-23

    Systems and methods for pulse-transmission low-power communication modes are disclosed. A pulse transmission transmitter includes: a clock; a pseudorandom polynomial generator coupled to the clock, the pseudorandom polynomial generator having a polynomial load input; an exclusive-OR gate coupled to the pseudorandom polynomial generator, the exclusive-OR gate having a serial data input; a programmable delay circuit coupled to both the clock and the exclusive-OR gate; a pulse generator coupled to the programmable delay circuit; and a higher order time derivative filter coupled to the pulse generator. The systems and methods significantly reduce lower-frequency emissions from pulse transmission spread-spectrum communication modes, which reduces potentially harmful interference to existing radio frequency services and users and also simultaneously permit transmission of multiple data bits by utilizing specific pulse shapes.

  19. Actuator assembly including a single axis of rotation locking member

    DOE Patents [OSTI]

    Quitmeyer, James N.; Benson, Dwayne M.; Geck, Kellan P.

    2009-12-08

    An actuator assembly including an actuator housing assembly and a single axis of rotation locking member fixedly attached to a portion of the actuator housing assembly and an external mounting structure. The single axis of rotation locking member restricting rotational movement of the actuator housing assembly about at least one axis. The single axis of rotation locking member is coupled at a first end to the actuator housing assembly about a Y axis and at a 90.degree. angle to an X and Z axis providing rotation of the actuator housing assembly about the Y axis. The single axis of rotation locking member is coupled at a second end to a mounting structure, and more particularly a mounting pin, about an X axis and at a 90.degree. angle to a Y and Z axis providing rotation of the actuator housing assembly about the X axis. The actuator assembly is thereby restricted from rotation about the Z axis.

  20. Hydraulic engine valve actuation system including independent feedback control

    DOE Patents [OSTI]

    Marriott, Craig D

    2013-06-04

    A hydraulic valve actuation assembly may include a housing, a piston, a supply control valve, a closing control valve, and an opening control valve. The housing may define a first fluid chamber, a second fluid chamber, and a third fluid chamber. The piston may be axially secured to an engine valve and located within the first, second and third fluid chambers. The supply control valve may control a hydraulic fluid supply to the piston. The closing control valve may be located between the supply control valve and the second fluid chamber and may control fluid flow from the second fluid chamber to the supply control valve. The opening control valve may be located between the supply control valve and the second fluid chamber and may control fluid flow from the supply control valve to the second fluid chamber.

  1. Fuel cell repeater unit including frame and separator plate

    SciTech Connect (OSTI)

    Yamanis, Jean; Hawkes, Justin R; Chiapetta, Jr., Louis; Bird, Connie E; Sun, Ellen Y; Croteau, Paul F

    2013-11-05

    An example fuel cell repeater includes a separator plate and a frame establishing at least a portion of a flow path that is operative to communicate fuel to or from at least one fuel cell held by the frame relative to the separator plate. The flow path has a perimeter and any fuel within the perimeter flow across the at least one fuel cell in a first direction. The separator plate, the frame, or both establish at least one conduit positioned outside the flow path perimeter. The conduit is outside of the flow path perimeter and is configured to direct flow in a second, different direction. The conduit is fluidly coupled with the flow path.

  2. Well casing hanger and packoff running and retrieval tool

    SciTech Connect (OSTI)

    Pollock, J.R.; Valka, W.A.

    1992-04-21

    This patent describes a well tool for running a casing hanger and a packoff into, and retrieving a packoff from, a subsea wellhead. It comprises a tubular body including means to releasably connect a packoff to the body for running the packoff into a subsea wellhead; means to releasably connect a packoff to the body for retrieving the packoff from a subsea wellhead; means to relocate the packoff running means and the packoff retrieving means between their functional and non-functional positions; means to releasably connect a casing hanger to the body for running the hanger into a subsea wellhead; a tubular mandrel surrounded by and rotatable with respect to the body; means surrounding the mandrel for moving the casing hanger connection means into functional position; first anti-rotation means preventing relative rotation between the body and the means for moving the casing hanger connection means; second anti-rotation means for preventing relative rotation between connection means; second anti-rotation means for preventing relative rotation between the body and a casing hanger connected thereto: and means for connecting the mandrel to a pipe string for running the tool into a subsea wellhead.

  3. Rapid assessment of redevelopment potential in marginal oil fields, application to the cut bank field 

    E-Print Network [OSTI]

    Chavez Ballesteros, Luis Eladio

    2005-02-17

    Incremental oil, MSTB 34 We attribute these observed waterflood performance characteristics to gravity segregation combined with generally higher permeability at the base of the Cut Bank sand, neither of which are captured in the single-layer synthetic model.... Infill predictions on a single-phase synthetic case showed greater accuracy than results from statistical techniques. The methodology successfully identified infill well locations iv on a synthetic case derived from Cut Bank field, a water-flooded oil...

  4. Testing geopressured geothermal reservoirs in existing wells. Wells of Opportunity Program final contract report, 1980-1981

    SciTech Connect (OSTI)

    Not Available

    1982-01-01

    The geopressured-geothermal candidates for the Wells of Opportunity program were located by the screening of published information on oil industry activity and through direct contact with the oil and gas operators. This process resulted in the recommendation to the DOE of 33 candidate wells for the program. Seven of the 33 recommended wells were accepted for testing. Of these seven wells, six were actually tested. The first well, the No. 1 Kennedy, was acquired but not tested. The seventh well, the No. 1 Godchaux, was abandoned due to mechanical problems during re-entry. The well search activities, which culminated in the acceptance by the DOE of 7 recommended wells, were substantial. A total of 90,270 well reports were reviewed, leading to 1990 wells selected for thorough geological analysis. All of the reservoirs tested in this program have been restricted by one or more faults or permeability barriers. A comprehensive discussion of test results is presented.

  5. Including environmental concerns in management strategies for depleted uranium hexafluoride

    SciTech Connect (OSTI)

    Goldberg, M. [Argonne National Laboratory, Washington, DC (United States); Avci, H.I. [Argonne National Lab., IL (United States); Bradley, C.E. [USDOE, Washington, DC (United States)

    1995-12-31

    One of the major programs within the Office of Nuclear Energy, Science, and Technology of the US Department of Energy (DOE) is the depleted uranium hexafluoride (DUF{sub 6}) management program. The program is intended to find a long-term management strategy for the DUF{sub 6} that is currently stored in approximately 46,400 cylinders at Paducah, KY; Portsmouth, OH; and Oak Ridge, TN, USA. The program has four major components: technology assessment, engineering analysis, cost analysis, and the environmental impact statement (EIS). From the beginning of the program, the DOE has incorporated the environmental considerations into the process of strategy selection. Currently, the DOE has no preferred alternative. The results of the environmental impacts assessment from the EIS, as well as the results from the other components of the program, will be factored into the strategy selection process. In addition to the DOE`s current management plan, other alternatives continued storage, reuse, or disposal of depleted uranium, will be considered in the EIS. The EIS is expected to be completed and issued in its final form in the fall of 1997.

  6. Two-dimensional nonlinear finite element analysis of well damage due to reservoir compaction, well-to-well interactions, and localization on weak layers

    SciTech Connect (OSTI)

    Hilbert, L.B. Jr. [Univ. of California, Berkeley, CA (United States); Fredrich, J.T. [Sandia National Labs., Albuquerque, NM (United States); Bruno, M.S. [Terralog Technologies USA, Inc., Arcadia, CA (United States); Deitrick, G.L.; Rouffignac, E.P. de [Shell Exploration and Production Co., Houston, TX (United States)

    1996-05-01

    In this paper the authors present the results of a coupled nonlinear finite element geomechanics model for reservoir compaction and well-to-well interactions for the high-porosity, low strength diatomite reservoirs of the Belridge field near Bakersfield, California. They show that well damage and failures can occur under the action of two distinct mechanisms: shear deformations induced by pore compaction, and subsidence, and shear deformations due to well-to-well interactions during production or water injection. They show such casting damage or failure can be localized to weak layers that slide or slip under shear due to subsidence. The magnitude of shear displacements and surface subsidence agree with field observations.

  7. Mathematical modeling of silica deposition in Tongonan-I reinjection wells, Philippines

    SciTech Connect (OSTI)

    Malate, R.C.M.; O`Sullivan, M.J.

    1993-10-01

    Mathematical models of silica deposition are derived using the method of characteristics for the problem of variable rate injection into a well producing radially symmetric flow. Solutions are developed using the first order rate equation of silica deposition suggested by Rimstidt and Barnes (1980). The changes in porosity and permeability resulting from deposition are included in the models. The models developed are successfully applied in simulating the changes in injection capacity in some of the reinjection wells in Tongonan geothermal field, Philippines.

  8. Reducing or stopping the uncontrolled flow of fluid such as oil from a well

    DOE Patents [OSTI]

    Hermes, Robert E

    2014-02-18

    The uncontrolled flow of fluid from an oil or gas well may be reduced or stopped by injecting a composition including 2-cyanoacrylate ester monomer into the fluid stream. Injection of the monomer results in a rapid, perhaps instantaneous, polymerization of the monomer within the flow stream of the fluid. This polymerization results in formation of a solid plug that reduces or stops the flow of additional fluid from the well.

  9. C -parameter distribution at N 3 LL ' including power corrections

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Hoang, André H.; Kolodrubetz, Daniel W.; Mateu, Vicent; Stewart, Iain W.

    2015-05-01

    We compute the e?e? C-parameter distribution using the soft-collinear effective theory with a resummation to next-to-next-to-next-to-leading-log prime accuracy of the most singular partonic terms. This includes the known fixed-order QCD results up to O(?3s), a numerical determination of the two-loop nonlogarithmic term of the soft function, and all logarithmic terms in the jet and soft functions up to three loops. Our result holds for C in the peak, tail, and far tail regions. Additionally, we treat hadronization effects using a field theoretic nonperturbative soft function, with moments ?n. To eliminate an O(?QCD) renormalon ambiguity in the soft function, we switchmore »from the MS¯ to a short distance “Rgap” scheme to define the leading power correction parameter ?1. We show how to simultaneously account for running effects in ?1 due to renormalon subtractions and hadron-mass effects, enabling power correction universality between C-parameter and thrust to be tested in our setup. We discuss in detail the impact of resummation and renormalon subtractions on the convergence. In the relevant fit region for ?s(mZ) and ?1, the perturbative uncertainty in our cross section is ? 2.5% at Q=mZ.« less

  10. C -parameter distribution at N 3 LL ' including power corrections

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Hoang, André H.; Kolodrubetz, Daniel W.; Mateu, Vicent; Stewart, Iain W.

    2015-05-01

    We compute the e?e? C-parameter distribution using the soft-collinear effective theory with a resummation to next-to-next-to-next-to-leading-log prime accuracy of the most singular partonic terms. This includes the known fixed-order QCD results up to O(?3s), a numerical determination of the two-loop nonlogarithmic term of the soft function, and all logarithmic terms in the jet and soft functions up to three loops. Our result holds for C in the peak, tail, and far tail regions. Additionally, we treat hadronization effects using a field theoretic nonperturbative soft function, with moments ?n. To eliminate an O(?QCD) renormalon ambiguity in the soft function, we switch from the MS¯ to a short distance “Rgap” scheme to define the leading power correction parameter ?1. We show how to simultaneously account for running effects in ?1 due to renormalon subtractions and hadron-mass effects, enabling power correction universality between C-parameter and thrust to be tested in our setup. We discuss in detail the impact of resummation and renormalon subtractions on the convergence. In the relevant fit region for ?s(mZ) and ?1, the perturbative uncertainty in our cross section is ? 2.5% at Q=mZ.

  11. Extractant composition including crown ether and calixarene extractants

    DOE Patents [OSTI]

    Meikrantz, David H. (Idaho Falls, ID); Todd, Terry A. (Aberdeen, ID); Riddle, Catherine L. (Idaho Falls, ID); Law, Jack D. (Pocalello, ID); Peterman, Dean R. (Idaho Falls, ID); Mincher, Bruce J. (Idaho Falls, ID); McGrath, Christopher A. (Blackfoot, ID); Baker, John D. (Blackfoot, ID)

    2009-04-28

    An extractant composition comprising a mixed extractant solvent consisting of calix[4] arene-bis-(tert-octylbenzo)-crown-6 ("BOBCalixC6"), 4',4',(5')-di-(t-butyldicyclo-hexano)-18-crown-6 ("DtBu18C6"), and at least one modifier dissolved in a diluent. The DtBu18C6 may be present at from approximately 0.01M to approximately 0.4M, such as at from approximately 0.086 M to approximately 0.108 M. The modifier may be 1-(2,2,3,3-tetrafluoropropoxy)-3-(4-sec-butylphenoxy)-2-propanol ("Cs-7SB") and may be present at from approximately 0.01M to approximately 0.8M. In one embodiment, the mixed extractant solvent includes approximately 0.15M DtBu18C6, approximately 0.007M BOBCalixC6, and approximately 0.75M Cs-7SB modifier dissolved in an isoparaffinic hydrocarbon diluent. The extractant composition further comprises an aqueous phase. The mixed extractant solvent may be used to remove cesium and strontium from the aqueous phase.

  12. Interim performance criteria for photovoltaic energy systems. [Glossary included

    SciTech Connect (OSTI)

    DeBlasio, R.; Forman, S.; Hogan, S.; Nuss, G.; Post, H.; Ross, R.; Schafft, H.

    1980-12-01

    This document is a response to the Photovoltaic Research, Development, and Demonstration Act of 1978 (P.L. 95-590) which required the generation of performance criteria for photovoltaic energy systems. Since the document is evolutionary and will be updated, the term interim is used. More than 50 experts in the photovoltaic field have contributed in the writing and review of the 179 performance criteria listed in this document. The performance criteria address characteristics of present-day photovoltaic systems that are of interest to manufacturers, government agencies, purchasers, and all others interested in various aspects of photovoltaic system performance and safety. The performance criteria apply to the system as a whole and to its possible subsystems: array, power conditioning, monitor and control, storage, cabling, and power distribution. They are further categorized according to the following performance attributes: electrical, thermal, mechanical/structural, safety, durability/reliability, installation/operation/maintenance, and building/site. Each criterion contains a statement of expected performance (nonprescriptive), a method of evaluation, and a commentary with further information or justification. Over 50 references for background information are also given. A glossary with definitions relevant to photovoltaic systems and a section on test methods are presented in the appendices. Twenty test methods are included to measure performance characteristics of the subsystem elements. These test methods and other parts of the document will be expanded or revised as future experience and needs dictate.

  13. Salt Wells Geothermal Exploratory Drilling Program EA(DOI-BLM...

    Open Energy Info (EERE)

    Salt Wells Geothermal Exploratory Drilling Program EA (DOI-BLM-NV-C010-2009-0006-EA) Jump to: navigation, search OpenEI Reference LibraryAdd to library Web Site: Salt Wells...

  14. Spin-orbit interaction in multiple quantum wells

    SciTech Connect (OSTI)

    Hao, Ya-Fei

    2015-01-07

    In this paper, we investigate how the structure of multiple quantum wells affects spin-orbit interactions. To increase the interface-related Rashba spin splitting and the strength of the interface-related Rashba spin-orbit interaction, we designed three kinds of multiple quantum wells. We demonstrate that the structure of the multiple quantum wells strongly affected the interface-related Rashba spin-orbit interaction, increasing the interface-related Rashba spin splitting to up to 26% larger in multiple quantum wells than in a stepped quantum well. We also show that the cubic Dresselhaus spin-orbit interaction similarly influenced the spin relaxation time of multiple quantum wells and that of a stepped quantum well. The increase in the interface-related Rashba spin splitting originates from the relationship between interface-related Rashba spin splitting and electron probability density. Our results suggest that multiple quantum wells can be good candidates for spintronic devices.

  15. Hot exciton transport in ZnSe quantum wells

    E-Print Network [OSTI]

    Zhao, Hui; Moehl, Sebastian; Wachter, Sven; Kalt, Heinz

    2002-02-01

    The in-plane transport of excitons in ZnSe quantum wells is investigated directly by microphotoluminescence in combination with a solid immersion lens. Due to the strong Froehlich coupling, the initial kinetic energy of the excitons is well...

  16. Pressure transient testing and productivity analysis for horizontal wells 

    E-Print Network [OSTI]

    Cheng, Yueming

    2004-11-15

    This work studied the productivity evaluation and well test analysis of horizontal wells. The major components of this work consist of a 3D coupled reservoir/wellbore model, a productivity evaluation, a deconvolution ...

  17. Exploratory Well At Long Valley Caldera Geothermal Area (Sorey...

    Open Energy Info (EERE)

    1983 to the east and north of Highway 395. Notes Among these wells were exploration and monitoring wells drilled near the Fish Hatchery Springs in preparation for the siting of a...

  18. Seismic Modelling for the Sub-Basalt Imaging Problem Including an Analysis and Development of the Boundary Element Method 

    E-Print Network [OSTI]

    Dobson, Andrew

    The north-east Atlantic margin (NEAM) is important for hydrocarbon exploration because of the growing evidence of hydrocarbon reserves in the region. However, seismic exploration of the sub-surface is hampered by large ...

  19. HOW MIGHT INDUSTRY GOVERNANCE BE BROADENED TO INCLUDE NONPROLIFERATION

    SciTech Connect (OSTI)

    Hund, Gretchen; Seward, Amy M.

    2009-10-06

    Broadening industry governance to support nonproliferation could provide significant new leverage in preventing the spread/diversion of nuclear, radiological, or dual-use material or technology that could be used in making a nuclear or radiological weapon. Industry is defined broadly to include 1) the nuclear industry, 2) dual-use industries, and 3) radioactive source manufacturers and selected radioactive source-user industries worldwide. This paper describes how industry can be an important first line of defense in detecting and thwarting proliferation, such as an illicit trade network or an insider theft case, by complementing and strengthening existing governmental efforts. For example, the dual-use industry can play a critical role by providing export, import, or security control information that would allow a government or the International Atomic Energy Agency (IAEA) to integrate this information with safeguards, export, import, and physical protection information it has to create a more complete picture of the potential for proliferation. Because industry is closest to users of the goods and technology that could be illicitly diverted throughout the supply chain, industry information can potentially be more timely and accurate than other sources of information. Industry is in an ideal position to help ensure that such illicit activities are detected. This role could be performed more effectively if companies worked together within a particular industry to promote nonproliferation by implementing an industry-wide self-regulation program. Performance measures could be used to ensure their materials and technologies are secure throughout the supply chain and that customers are legitimately using and/or maintaining oversight of these items. Nonproliferation is the overarching driver that industry needs to consider in adopting and implementing a self-regulation approach. A few foreign companies have begun such an approach to date; it is believed that, ultimately, broad engagement of global industry leaders in self regulation is needed to result in the greatest nonproliferation benefit.

  20. Community Assessment Tool for Public Health Emergencies Including Pandemic Influenza

    SciTech Connect (OSTI)

    HCTT-CHE

    2011-04-14

    The Community Assessment Tool (CAT) for Public Health Emergencies Including Pandemic Influenza (hereafter referred to as the CAT) was developed as a result of feedback received from several communities. These communities participated in workshops focused on influenza pandemic planning and response. The 2008 through 2011 workshops were sponsored by the Centers for Disease Control and Prevention (CDC). Feedback during those workshops indicated the need for a tool that a community can use to assess its readiness for a disaster—readiness from a total healthcare perspective, not just hospitals, but the whole healthcare system. The CAT intends to do just that—help strengthen existing preparedness plans by allowing the healthcare system and other agencies to work together during an influenza pandemic. It helps reveal each core agency partners' (sectors) capabilities and resources, and highlights cases of the same vendors being used for resource supplies (e.g., personal protective equipment [PPE] and oxygen) by the partners (e.g., public health departments, clinics, or hospitals). The CAT also addresses gaps in the community's capabilities or potential shortages in resources. While the purpose of the CAT is to further prepare the community for an influenza pandemic, its framework is an extension of the traditional all-hazards approach to planning and preparedness. As such, the information gathered by the tool is useful in preparation for most widespread public health emergencies. This tool is primarily intended for use by those involved in healthcare emergency preparedness (e.g., community planners, community disaster preparedness coordinators, 9-1-1 directors, hospital emergency preparedness coordinators). It is divided into sections based on the core agency partners, which may be involved in the community's influenza pandemic influenza response.