Powered by Deep Web Technologies
Note: This page contains sample records for the topic "includes finished motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Finished Motor Gasoline Net Production  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: Finished motor gasoline ...

2

Finished Motor Gasoline Net Production  

Gasoline and Diesel Fuel Update (EIA)

Data Series: Finished Motor Gasoline Finished Motor Gasoline (less Adj.) Reformulated Gasoline Reformulated Gasoline Blenede w/ Fuel Ethanol Reformulated Other Gasoline Conventional Gasoline Conventional Gasoline Blended w/ Fuel Ethanol Conventional Gasoline Blended w/ Fuel Ethanol, Ed55 & Ed55 Other Conventional Gasoline Finished Motor Gasoline Adjustment Kerosene-Type Jet Fuel Kerosene-Type Jet, Commercial Kerosene-Type Jet, Military Distillate Fuel Oil Distillate Fuel Oil, 15 ppm Sulfur and Under Distillate Fuel Oil > 15 ppm to 500 ppm Sulfur Distillate Fuel Oil > 500 ppm Sulfur Residual Fuel Oil Propane/Propylene Period: Weekly 4-Week Average

3

Michigan Finished Motor Gasoline Stocks at Refineries, Bulk ...  

U.S. Energy Information Administration (EIA)

Michigan Finished Motor Gasoline Stocks at Refineries, Bulk Terminals, and Natural Gas Plants (Thousand Barrels)

4

Colorado Finished Motor Gasoline Stocks at Refineries, Bulk ...  

U.S. Energy Information Administration (EIA)

Colorado Finished Motor Gasoline Stocks at Refineries, Bulk Terminals, and Natural Gas Plants (Thousand Barrels)

5

Blender Net Production of Finished Motor Gasoline  

U.S. Energy Information Administration (EIA) Indexed Site

Product: Total Finished Motor Gasoline Reformulated Gasoline Reformulated Blended w/ Fuel Ethanol Reformulated Other Conventional Gasoline Conventional Blended w/ Fuel Ethanol Conventional Blended w/ Fuel Ethanol, Ed55 and Lower Conventional Blended w/ Fuel Ethanol, Greater than Ed55 Conventional Other Finished Aviation Gasoline Kerosene-Type Jet Fuel Kerosene Distillate Fuel Oil Distillate F.O., 15 ppm Sulfur and under Distillate F.O., Greater than 15 ppm to 500 ppm Sulfur Distillate F.O., Greater than 500 ppm Sulfur Residual Fuel Oil Residual Fuel Less Than 0.31 Percent Sulfur Residual Fuel 0.31 to 1.00 Percent Sulfur Residual Fuel Greater Than 1.00 Percent Sulfur Special Naphthas Lubricants Asphalt and Road Oil Miscellaneous Products Processing Gain(-) or Loss(+) Period-Unit: Monthly-Thousand Barrels Monthly-Thousand Barrels per Day Annual-Thousand Barrels Annual-Thousand Barrels per Day

6

Refiner and Blender Net Production of Finished Motor Gasoline  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: Finished motor gasoline ...

7

U.S. Exports of Finished Motor Gasoline (Thousand Barrels)  

U.S. Energy Information Administration (EIA)

U.S. Exports of Finished Motor Gasoline (Thousand Barrels) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9; 1930's: 30,613: 28,646 ...

8

U.S. Imports from Venezuela of Finished Motor Gasoline (Thousand ...  

U.S. Energy Information Administration (EIA)

U.S. Imports from Venezuela of Finished Motor Gasoline (Thousand Barrels) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec; 1993: 1,856: 1,700: 945: 1,181: 1,074 ...

9

Finishing  

Science Conference Proceedings (OSTI)

Table 3   Recommended finishing procedures...spirally sewn sections 150 or 180 Polishing tallow or No. 180 emergy grease cake 30??40 6000??7500 Grease coloring 88??88 unbleached sheeting, spirally sewn or

10

Finishing  

Science Conference Proceedings (OSTI)

Table 12   Recommended finishing procedures for nickel alloys...spiral-sewn sections 150 or 180 Polishing tallow or No. 180 emery grease cake 30??40 6,000??7,500 Grease coloring 88-88 unbleached sheeting, spiral-sewn or loose disk;

11

Stocks of Finished Motor Gasoline - U.S. Energy Information ...  

U.S. Energy Information Administration (EIA)

Weekly data for RBOB with Ether, RBOB with Alcohol, and Reformulated GTAB Motor Gasoline Blending Components are discontinued as of the week ending June 4, ...

12

Stocks of Finished Motor Gasoline - U.S. Energy Information ...  

U.S. Energy Information Administration (EIA)

Reformulated and conventional gasoline production excludes adjustments for fuel ethanol and motor gasoline blending components. Historical data prior to June 4, ...

13

Writing Motor Specifications - How to Include Efficiency  

E-Print Network (OSTI)

The escalating cost of electric power coupled with the rapid depletion of our non-renewable resources makes consideration of motor efficiency good sense both from economic and conservation viewpoints. The efficiency of an electric motor can be assessed during bid evaluation by applying loss penalties: however, the actual value can be influenced at an earlier stage by a careful review of what goes into the motor specification.

Quartermaine, B. J.

1980-01-01T23:59:59.000Z

14

Finished Motor Gasoline Imports by Area of Entry  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: Crude oil includes ...

15

Stocks of Finished Motor Gasoline - U.S. Energy Information ...  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: Stocks include those ...

16

,"Finished Motor Gasoline Refinery, Bulk Terminal, and Natural Gas Plant Stocks"  

U.S. Energy Information Administration (EIA) Indexed Site

Monthly","9/2013","1/15/1993" Monthly","9/2013","1/15/1993" ,"Release Date:","11/27/2013" ,"Next Release Date:","Last Week of December 2013" ,"Excel File Name:","pet_stoc_st_a_epm0f_str_mbbl_m.xls" ,"Available from Web Page:","http://www.eia.gov/dnav/pet/pet_stoc_st_a_epm0f_str_mbbl_m.htm" ,"Source:","Energy Information Administration" ,"For Help, Contact:","infoctr@eia.gov" ,,"(202) 586-8800",,,"11/25/2013 11:32:19 AM" "Back to Contents","Data 1: Finished Motor Gasoline Refinery, Bulk Terminal, and Natural Gas Plant Stocks" "Sourcekey","MGFSXUS1","MGFSXP11","MGFSXCT1","MGFS3_SDE_1","MGFSXFL1","MGFSXGA1","MGFS3_SME_1","MGFS3_SMD_1","MGFSXMA1","MGFS3_SNH_1","MGFSXNJ1","MGFSXNY1","MGFSXNC1","MGFSXPA1","MGFSXRI1","MGFSXSC1","MGFS3_SVT_1","MGFSXVA1","MGFSXWV1","MGFSXP21","MGFSXIL1","MGFSXIN1","MGFSXIA1","MGFS3_SKS_1","MGFSXKY1","MGFSXMI1","MGFSXMN1","MGFSXMO1","MGFS3_SNE_1","MGFS3_SND_1","MGFSXOH1","MGFSXOK1","MGFS3_SSD_1","MGFSXTN1","MGFSXWI1","MGFSXP31","MGFSXAL1","MGFSXAR1","MGFSXLA1","MGFSXMS1","MGFSXNM1","MGFSXTX1","MGFSXP41","MGFSXCO1","MGFSXID1","MGFSXMT1","MGFSXUT1","MGFSXWY1","MGFSXP51","MGFSXAK1","MGFSXAZ1","MGFSXCA1","MGFSXHI1","MGFSXNV1","MGFSXOR1","MGFSXWA1"

17

,"Finished Motor Gasoline Refinery, Bulk Terminal, and Natural Gas Plant Stocks"  

U.S. Energy Information Administration (EIA) Indexed Site

Annual",2012,"6/30/1993" Annual",2012,"6/30/1993" ,"Release Date:","9/27/2013" ,"Next Release Date:","9/26/2014" ,"Excel File Name:","pet_stoc_st_a_epm0f_str_mbbl_a.xls" ,"Available from Web Page:","http://www.eia.gov/dnav/pet/pet_stoc_st_a_epm0f_str_mbbl_a.htm" ,"Source:","Energy Information Administration" ,"For Help, Contact:","infoctr@eia.gov" ,,"(202) 586-8800",,,"11/25/2013 11:32:18 AM" "Back to Contents","Data 1: Finished Motor Gasoline Refinery, Bulk Terminal, and Natural Gas Plant Stocks" "Sourcekey","MGFSXUS1","MGFSXP11","MGFSXCT1","MGFS3_SDE_1","MGFSXFL1","MGFSXGA1","MGFS3_SME_1","MGFS3_SMD_1","MGFSXMA1","MGFS3_SNH_1","MGFSXNJ1","MGFSXNY1","MGFSXNC1","MGFSXPA1","MGFSXRI1","MGFSXSC1","MGFS3_SVT_1","MGFSXVA1","MGFSXWV1","MGFSXP21","MGFSXIL1","MGFSXIN1","MGFSXIA1","MGFS3_SKS_1","MGFSXKY1","MGFSXMI1","MGFSXMN1","MGFSXMO1","MGFS3_SNE_1","MGFS3_SND_1","MGFSXOH1","MGFSXOK1","MGFS3_SSD_1","MGFSXTN1","MGFSXWI1","MGFSXP31","MGFSXAL1","MGFSXAR1","MGFSXLA1","MGFSXMS1","MGFSXNM1","MGFSXTX1","MGFSXP41","MGFSXCO1","MGFSXID1","MGFSXMT1","MGFSXUT1","MGFSXWY1","MGFSXP51","MGFSXAK1","MGFSXAZ1","MGFSXCA1","MGFSXHI1","MGFSXNV1","MGFSXOR1","MGFSXWA1"

18

Nuclear Maintenance Applications Center: Motor Management Guide Supporting Plant License Renewal Including Environmental Qualification Considerations  

Science Conference Proceedings (OSTI)

This report was developed by the Electric Power Research Institutes Large Electric Motor Users Group Information Working Group, which includes motor engineers, motor specialist consultants, and vendors. Environmental qualification (EQ) program owners were also involved in the development of this report. This report addresses the most important elements of a sound motor management program to support an informed decision on motor preservation and motor life extension. Motor life extensions of ...

2013-06-07T23:59:59.000Z

19

DOT Motor-fuel use statistics summary to 1995 The data included...  

Open Energy Info (EERE)

Motor-fuel use statistics summary to 1995 The data included in this submission is United States Department of Transportation (DOT) data up to 1995. The data includes motor-fuel...

20

Motor Systems Assessment Training, Including Use of the Motor Systems Tool Suite  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Motor Systems Assessment Training Motor Systems Assessment Training Presented by: Gilbert McCoy, PE Washington State University Extension Energy Program (360) 956-2086 mccoyg@energy.wsu.edu 2 Motor Systems Assessment Training 3 Motor Systems Assessment Training Department of Energy Information Resources U.S. DOE Industrial Technologies Program (ITP) BestPractices Website www.eere.energy.gov/industry/bestpractices EERE Information Center (877) 337-3463 Or www.eere.energy.gov/informationcenter 4 Motor Systems Assessment Training Big Picture Perspectives: Industrial Motor Systems Industrial motor systems: � Are the single largest electrical end use category in the American economy � Account for 23% of U.S. electrical sales. 5 Motor Systems Assessment Training Ultimate

Note: This page contains sample records for the topic "includes finished motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

U.S. Product Supplied of Finished Motor Gasoline (Thousand Barrels)  

U.S. Energy Information Administration (EIA)

1970's: 2,111,349: 2,195,268: 2,333,778: 2,436,156: ... Motor Gasoline Supply and Disposition; ... U.S. Product Supplied for Crude Oil and Petroleum Products ...

22

U.S. Product Supplied of Finished Motor Gasoline (Thousand Barrels ...  

U.S. Energy Information Administration (EIA)

1970's: 5,785: 6,014: 6,376: 6,674: 6,537: 6,675: 6,978: 7,177: ... Motor Gasoline Supply and Disposition; ... U.S. Product Supplied for Crude Oil and Petroleum ...

23

DISPOSAL OF TRU WASTE FROM THE PLUTONIUM FINISHING PLANT IN PIPE OVERPACK CONTAINERS TO WIPP INCLUDING NEW SECURITY REQUIREMENTS  

Science Conference Proceedings (OSTI)

The Department of Energy is responsible for the safe management and cleanup of the DOE complex. As part of the cleanup and closure of the Plutonium Finishing Plant (PFP) located on the Hanford site, the nuclear material inventory was reviewed to determine the appropriate disposition path. Based on the nuclear material characteristics, the material was designated for stabilization and packaging for long term storage and transfer to the Savannah River Site or, a decision for discard was made. The discarded material was designated as waste material and slated for disposal to the Waste Isolation Pilot Plant (WIPP). Prior to preparing any residue wastes for disposal at the WIPP, several major activities need to be completed. As detailed a processing history as possible of the material including origin of the waste must be researched and documented. A technical basis for termination of safeguards on the material must be prepared and approved. Utilizing process knowledge and processing history, the material must be characterized, sampling requirements determined, acceptable knowledge package and waste designation completed prior to disposal. All of these activities involve several organizations including the contractor, DOE, state representatives and other regulators such as EPA. At PFP, a process has been developed for meeting the many, varied requirements and successfully used to prepare several residue waste streams including Rocky Flats incinerator ash, Hanford incinerator ash and Sand, Slag and Crucible (SS&C) material for disposal. These waste residues are packed into Pipe Overpack Containers for shipment to the WIPP.

Hopkins, A.M.; Sutter, C.; Hulse, G.; Teal, J.

2003-02-27T23:59:59.000Z

24

Finished Motor Gasoline Exports  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: Crude oil exports are ...

25

Finishing in the Future  

NLE Websites -- All DOE Office Websites (Extended Search)

of qualities Metagenomic assemblies Genome Finishing: Finishing systems and pipelines (automated, manual, etc.) Next generation finishing tools and technologies Quality...

26

U.S. total motor gasoline exports down slightly from last year but ...  

U.S. Energy Information Administration (EIA)

Greenhouse gas data, voluntary report- ing, electric power plant emissions. ... Total motor gasoline = finished motor gasoline + motor gasoline blending components.

27

Finishing in the Future  

NLE Websites -- All DOE Office Websites (Extended Search)

Single cell and metagenomic assemblies Genome Finishing: Finishing systems and pipelines (automated, manual, etc.) Next generation finishing tools and technologies Quality...

28

Finishing in the Future  

NLE Websites -- All DOE Office Websites (Extended Search)

Single cell and metagenomic assemblies Genome Finishing: Finishing systems and pipelines (automated, manual, etc.) Next generation finishing tools and technologies Human...

29

A power system includes an engine, a motor/generator operatively connected to the engine, and a starter operatively connected to at least one of the engine and the motor/generator.  

Science Conference Proceedings (OSTI)

A power system includes an engine, a motor/generator operatively connected to the engine, and a starter operatively connected to at least one of the engine and the motor/generator.

Hoff, Brian D. (East Peoria, IL); Algrain, Marcelo C. (Peoria, IL)

2008-12-09T23:59:59.000Z

30

Product Supplied for Finished Gasoline - U.S. Energy ...  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: Finished motor gasoline ...

31

Mass Finishing  

Science Conference Proceedings (OSTI)

Table 8 Operating conditions for mass finishing...Brass screw-machine parts Aluminum oxide or granite 6.4-19 0.25-0.75 [MathExpression] -6 Light matte or bright Light cutting (a) Brass stampings or screws (b) Limestone 3.2-13 0.13-0.50 2-6 Bright (a) Submerged tumbling is used for fragile and precision parts. (b) Screw-machine parts...

32

Finishing in the Future  

NLE Websites -- All DOE Office Websites (Extended Search)

technologies (454, Solexa, etc.) Finishing Processes: Finishing systems and pipelines (automated, manual, etc.) Solving genome gaps, hard stops & other difficult areas...

33

Finishing Wood Decks  

E-Print Network (OSTI)

Wood decks have become an important part of residential construction in recent years. However, there is considerable confusion regarding how these structures should be protected with finish. This paper summarizes the types, application techniques, and expected service lives of various finishes on both preservative treated and untreated lumber. Recommendations are made on the basis of decades of research on various wood species using a wide variety of finishes.

R. Sam Williams; et al.

1993-01-01T23:59:59.000Z

34

Finished Motor Gasoline Imports from Taiwan  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: *Countries listed under ...

35

Finished Motor Gasoline Imports from Venezuela  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: *Countries listed under ...

36

Finished Motor Gasoline Imports from All Countries  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: *Countries listed under ...

37

Finished Motor Gasoline Imports from Thailand  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: *Countries listed under ...

38

Finished Motor Gasoline Imports from Algeria  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: *Countries listed under ...

39

Finished Motor Gasoline Imports from Australia  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: *Countries listed under ...

40

Product Supplied for Finished Motor Gasoline  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: Data may not add to ...

Note: This page contains sample records for the topic "includes finished motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Finished Motor Gasoline Exports by Destination  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: Crude oil exports are ...

42

U.S. Finished Motor Gasoline Imports  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: *Countries listed under ...

43

Refinery Net Production of Finished Motor Gasoline  

U.S. Energy Information Administration (EIA)

La. Gulf Coast: 6,478: 8,150: 8,125: 7,209: 7,676: 7,807: 2005-2013: N. La., Ark: 222: 358: 274: 337: 284: 321: 2005-2013: New Mexico: 1,533: 1,555: ...

44

Finished Motor Gasoline Imports from India  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: *Countries listed under ...

45

Finished Motor Gasoline Imports from Persian Gulf  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: *Countries listed under ...

46

Refinery Yield of Finished Motor Gasoline  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: Totals may not equal ...

47

Midwest (PADD 2) Finished Motor Gasoline Imports  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: *Countries listed under ...

48

Finished Motor Gasoline Imports from OPEC  

U.S. Energy Information Administration (EIA)

Indonesia withdrew from OPEC in January 2009, Angola joined OPEC in January 2007, Ecuador withdrew from OPEC in January 1993 and rejoined in November ...

49

Refiner and Blender Inputs of Motor Gasoline Blending Components  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: Finished motor gasoline ...

50

Imports of Total Motor Gasoline - U.S. Energy Information ...  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: Finished motor gasoline ...

51

Vibratory finishing as a decontamination process  

SciTech Connect

The major objective of this research is to develop vibratory finishing into a large-scale decontamination technique that can economicaly remove transuranic and other surface contamination from large volumes of waste produced by the operation and decommissioning of retired nuclear facilities. The successful development and widespread application of this decontamination technique would substantially reduce the volume of waste requiring expensive geologic disposal. Other benefits include exposure reduction for decontamination personnel and reduced risk of environmental contamination. Laboratory-scale studies showed that vibratory finishing can rapidly reduce the contamination level of transuranic-contaminated stainless steel and Plexiglas to well below the 10-nCi/g limit. The capability of vibratory finishing as a decontamination process was demonstrated on a large scale. The first decontamination demonstration was conducted at the Hanford N-Reactor, where a vibratory finisher was installed to reduce personnel exposure during the summer outage. Items decontaminated included fuel spacers, process-tube end caps, process-tube inserts, pump parts, ball-channel inspection tools and miscellaneous hand tools. A second demonstration is currently being conducted in the decontamination facility at the Hanford 231-Z Building. During this demonstration, transuranic-contaminated material from decommissioned plutonium facilities is being decontaminated to <10 nCi/g to minimize the volume of material that will require geologic disposal. Items that are being decontaminated include entire glove boxes, process-hood structural material and panels, process tanks, process-tank shields, pumps, valves and hand tools used during the decommissioning work.

McCoy, M.W.; Arrowsmith, H.W.; Allen, R.P.

1980-10-01T23:59:59.000Z

52

Sequencing, Finishing and Analysis in the Future Meeting  

NLE Websites -- All DOE Office Websites (Extended Search)

Sequencing, Finishing and Analysis in the Future Meeting Sequencing, Finishing and Analysis in the Future Meeting Wednesday - Friday, May 29 - 31, 2013 La Fonda Hotel in Santa Fe, NM Overview "Sequencing, Finishing and Analysis in the Future" (SFAF) is an annual meeting dedicated to bringing together experts in the field of genomic sequencing, finishing and analysis-including representatives from the industries that serve this specialized scientific community. The meeting focuses on laboratory methods and computational tools used to help sequence, assemble, and finish genomes, including new sequencing technologies, which promise high-throughput results by sequencing more base-pairs per run at longer read-lengths. In the past, companies have presented different techniques they have developed to achieve maximum balance for researchers.

53

Independent Activity Report, Hanford Plutonium Finishing Plant - May 2012 |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Hanford Plutonium Finishing Plant - Hanford Plutonium Finishing Plant - May 2012 Independent Activity Report, Hanford Plutonium Finishing Plant - May 2012 May 2012 Criticality Safety Information Meeting for the Hanford Plutonium Finishing Plant [HIAR-RL-2012-05-14] The U.S. Department of Energy's (DOE) Office of Enforcement and Oversight, within the Office of Health, Safety and Security (HSS), conducted a criticality safety information meeting with Hanford site criticality safety engineers on May 14, 2012, to discuss criticality safety issues and experiences principally with respect to the Decontamination and Decommissioning (D&D) activities at the Plutonium Finishing Plant (PFP). These discussions also included aspects of Non-Destructive Assay (NDA) in support of criticality safety evaluations.

54

EcoCAR Reaches the Finish Line | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Reaches the Finish Line Reaches the Finish Line EcoCAR Reaches the Finish Line June 21, 2011 - 2:09pm Addthis The EcoCAR Challenege is a competition that challenges participating students from across North America to re-engineer a vehicle donated by General Motors. With the goal of minimizing the vehicle's fuel consumption and emissions, while maintaining its utility, safety and performance, teams had to find the best combination of cutting-edge technologies to meet these objectives. Shannon Brescher Shea Communications Manager, Clean Cities Program Last Thursday, the Library of Congress's vaunted halls were filled with undergraduate and graduate students on the edge of their seats, waiting to hear the first place winner of the EcoCAR: The NeXt Challenge competition. As Patrick Davis, Vehicle Technologies Program Manager for the Department

55

EcoCAR Reaches the Finish Line | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

EcoCAR Reaches the Finish Line EcoCAR Reaches the Finish Line EcoCAR Reaches the Finish Line June 21, 2011 - 2:09pm Addthis The EcoCAR Challenege is a competition that challenges participating students from across North America to re-engineer a vehicle donated by General Motors. With the goal of minimizing the vehicle's fuel consumption and emissions, while maintaining its utility, safety and performance, teams had to find the best combination of cutting-edge technologies to meet these objectives. Shannon Brescher Shea Communications Manager, Clean Cities Program Last Thursday, the Library of Congress's vaunted halls were filled with undergraduate and graduate students on the edge of their seats, waiting to hear the first place winner of the EcoCAR: The NeXt Challenge competition. As Patrick Davis, Vehicle Technologies Program Manager for the Department

56

EcoCAR Challenge: Finish Line | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

EcoCAR Challenge: Finish Line EcoCAR Challenge: Finish Line EcoCAR Challenge: Finish Line Addthis Description The EcoCAR Challenege is a competition that challenges participating students from across North America to re-engineer a vehicle donated by General Motors. With the goal of minimizing the vehicle's fuel consumption and emissions, while maintaining its utility, safety and performance, teams had to find the best combination of cutting-edge technologies to meet these objectives. Speakers Secretary Steven Chu; MIchael Bly, Lynn Gnatt, Carlos Cubero-Ponce, Ryan Melsert, Eric Schacht, Andrew Eldridge, Duration 4:23 Topic Alternative Fuel Vehicles Fuel Economy Batteries Hydrogen & Fuel Cells Credit Energy Department Video (Music.) LYNN GANTT (Virginia Tech): There are 16 universities that compete in the

57

Advanced Manufacturing Office: MotorMaster+  

NLE Websites -- All DOE Office Websites (Extended Search)

schedules Motor inventory information, including motor nameplate information, operating profile, load status, and field measurements Life cycle economics, including depreciation...

58

Semi-finished modular cells  

E-Print Network (OSTI)

This thesis subject is a pre-fabricated element (cell): a system that employs natural, light, and economic materials to produce a near-finished portion of a building. The intent is to introduce sustainable design into ...

Bachelder, Laura Govoni, 1971-

2002-01-01T23:59:59.000Z

59

Surface treatment and finishing of aluminum and its alloys. Volumes 1 and 2 (5th revised and enlarged edition)  

SciTech Connect

Currently available technologies for treating and finishing Al and Al-alloy surfaces are surveyed in an introduction and reference handbook. Chapters are devoted to the properties, alloys, and finishes of Al; mechanical treatments and finishes; electrolytic and chemical polishing; chemical cleaning and etching; chemical conversion coatings; theoretical models of anodizing; decorative and protective anodizing; and anodizing in architecture. Also included are: hard anodizing, coloring anodic oxide coatings (AOCs) with dyes and pigments, sealing AOCs, properties and tests of AOCs, plating on Al, organic finishing, vitreous enameling, and effluents from Al-finishing operations. Diagrams, drawings, graphs, photographs, micrographs, and tables of national finish specifications are provided.

Sheasby, P.G.; Wernick, S.; Pinner, R.

1987-01-01T23:59:59.000Z

60

The Best Finish First: Sequence Finishing with Whole Genome Mapping ( 7th Annual SFAF Meeting, 2012)  

Science Conference Proceedings (OSTI)

Deacon Sweeney on "the Best Finish First: Sequence Finishing with Whole Genome Mapping" at the 2012 Sequencing, Finishing, Analysis in the Future Meeting held June 5-7, 2012 in Santa Fe, New Mexico.

Sweeney, Deacon [OpGen, Inc.

2012-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "includes finished motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Finishing in the Future  

NLE Websites -- All DOE Office Websites (Extended Search)

The Genome Institute, Washington University Areas of emphasis at this meeting included: Genome Sequencing: New sequencing technologies (454, illumina, SOLiD, Ion Torrent, MiSeq,...

62

Stepping Motor Control System  

E-Print Network (OSTI)

This paper describes a hardware system designed to facilitate position and velocity control of a group of eight stepping motors using a PDP-11. The system includes motor driver cards and other interface cards in addition ...

Larson, Noble G.

63

Motor/generator  

DOE Patents (OSTI)

A motor/generator is provided for connecting between a transmission input shaft and an output shaft of a prime mover. The motor/generator may include a motor/generator housing, a stator mounted to the motor/generator housing, a rotor mounted at least partially within the motor/generator housing and rotatable about a rotor rotation axis, and a transmission-shaft coupler drivingly coupled to the rotor. The transmission-shaft coupler may include a clamp, which may include a base attached to the rotor and a plurality of adjustable jaws.

Hickam, Christopher Dale (Glasford, IL)

2008-05-13T23:59:59.000Z

64

Finished Motor Gasoline Refinery, Bulk Terminal, and Natural Gas Plant  

U.S. Energy Information Administration (EIA) Indexed Site

Apr-13 May-13 Jun-13 Jul-13 Aug-13 Sep-13 View Apr-13 May-13 Jun-13 Jul-13 Aug-13 Sep-13 View History U.S. 31,576 31,334 35,019 34,533 32,174 27,872 1993-2013 PAD District 1 2,286 2,947 3,296 3,722 3,755 2,837 1993-2013 Connecticut 1993-2005 Delaware 1993-2010 Florida 635 638 666 711 724 563 1993-2013 Georgia 179 213 239 277 244 191 1993-2013 Maine 126 263 324 270 310 112 1993-2013 Maryland 1993-2009 Massachusetts 7 6 7 5 8 7 1993-2013 New Hampshire 1993-2006 New Jersey 206 344 270 604 785 463 1993-2013 New York 325 455 535 508 465 521 1993-2013 North Carolina 251 387 522 535 457 320 1993-2013 Pennsylvania 116 165 232 202 234 178 1993-2013 Rhode Island 1993-2007 South Carolina 250 237 271 306 293 275 1993-2013 Vermont 20 30 19 15 24 19 1993-2013

65

East Coast (PADD 1) Imports of Finished Motor Gasoline ...  

U.S. Energy Information Administration (EIA)

456: 487: 443: 2004: 334: 404: 523: 416: 450: 438: 559: 461: 498: 503: 579: 476: 2005: 476: 548: 486: 603: 540: 519: 547: 473: 600: 650: 542: 486: 2006: 578: 585: 497 ...

66

Gulf Coast (PADD 3) Exports of Finished Motor Gasoline ...  

U.S. Energy Information Administration (EIA)

1,954: 2,583: 2,551: 3,135: 2,694: 3,527: 3,139: 4,209: 1996: 4,440: 1,465: 3,618: 2,073: 2,298: 2,661: 3,539: 2,108: 1,928: 3,147: 2,937: 3,174: ...

67

U.S. Product Supplied of Finished Motor Gasoline (Thousand ...  

U.S. Energy Information Administration (EIA)

1954: 84,697: 80,745: 95,229: 98,007: 98,705: 106,226: 106,171: 103,984: 98,462: 99,807: 95,984: 97,610: 1955: 92,460: 84,778: 100,948: 106,216: ...

68

U.S. Imports of Finished Motor Gasoline (Thousand Barrels)  

U.S. Energy Information Administration (EIA)

1954: 2: 2: 1: 1: 2: 133: 133: 4: 15: 530: 198: 164: 1955: 307: 534: 575: 125: 310: 297: 384: 258: 1,063: 206: 537: 213: 1956: 11: 111: 84: 4: 139: ...

69

U.S. Exports of Finished Motor Gasoline (Thousand Barrels ...  

U.S. Energy Information Administration (EIA)

1954: 87: 101: 57: 85: 108: 112: 104: 92: 98: 102: 99: 85: 1955: 91: 81: 79: 79: 99: 96: 112: 103: 101: 104: 90: 97: 1956: 90: 56: 92: 92: 85: 88: ...

70

U.S. Exports of Finished Motor Gasoline (Thousand Barrels)  

U.S. Energy Information Administration (EIA)

1954: 2,705: 2,833: 1,776: 2,539: 3,359: 3,367: 3,232: 2,865: 2,942: 3,148: 2,967: 2,633: 1955: 2,829: 2,280: 2,452: 2,376: 3,077: 2,874: 3,486: ...

71

U.S. Imports from Venezuela of Finished Motor Gasoline ...  

U.S. Energy Information Administration (EIA)

Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9; 1990's: 40: 31: 28: 47: 44: 60: 64: 2000's: 72: 58: 44: 34: 30: 41: 16: 6: 2: 0: 2010's ...

72

Finished Motor Gasoline Imports from Trinidad and Tobago  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: *Countries listed under ...

73

Exports of Finished Motor Gasoline - U.S. Energy Information ...  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: RBOB with Ether and RBOB ...

74

Finished Motor Gasoline Exports - U.S. Energy Information ...  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: Crude oil exports are ...

75

U.S. Imports of Finished Motor Gasoline (Thousand Barrels)  

U.S. Energy Information Administration (EIA)

Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9; 1930's: 0: 78: 144: 79: 47: 1940's: 97: 335: 115: 5,736: 3,148: 1,807: 1: 358: 302: 0 ...

76

Weekly U.S. Product Supplied of Finished Motor Gasoline ...  

U.S. Energy Information Administration (EIA)

Year-Month Week 1 Week 2 Week 3 Week 4 Week 5; End Date Value End Date Value End Date Value End Date Value End Date Value; 1991-Feb : 02/08 : 6,621 : 02/15 : 6,433

77

Refinery & Blender Net Production of Finished Motor Gasoline  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: See Definitions ...

78

Gulf Coast (PADD 3) Finished Motor Gasoline Imports  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: *Countries listed under ...

79

Finished Motor Gasoline Refinery, Bulk Terminal, and Natural Gas Plant  

U.S. Energy Information Administration (EIA) Indexed Site

2007 2008 2009 2010 2011 2012 View 2007 2008 2009 2010 2011 2012 View History U.S. 71,470 61,525 55,254 40,534 39,717 37,768 1993-2012 PAD District 1 19,732 16,074 10,858 3,913 3,741 3,513 1993-2012 Connecticut 1993-2004 Delaware 292 105 498 1993-2009 Florida 4,484 1,877 914 586 734 747 1993-2012 Georgia 2,141 1,724 800 374 251 220 1993-2012 Maine 889 374 130 152 1993-2012 Maryland 67 31 1993-2008 Massachusetts 2 4 3 1993-2012 New Hampshire 1993-2005 New Jersey 1,982 2,956 2,026 667 275 795 1993-2012 New York 1,768 1,469 273 194 628 483 1993-2012 North Carolina 1,977 1,724 1,470 591 389 317 1993-2012 Pennsylvania 3,731 3,595 3,421 697 782 188 1993-2012 Rhode Island 1993-2005 South Carolina 839 720 787 444 276 288 1993-2012

80

Refinery & Blender Net Production of Finished Motor Gasoline  

U.S. Energy Information Administration (EIA)

La. Gulf Coast: 1,279: 1,050: 859: 598: 428: 364: 1993-2012: N. La., Ark: 48: 62: 85: 160: 222: 213: 1993-2012: New Mexico: 49: 50: 49: 65: 57: 60: ...

Note: This page contains sample records for the topic "includes finished motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Refinery & Blender Net Production of Total Finished Petroleum Products  

U.S. Energy Information Administration (EIA) Indexed Site

& Blender Net Production & Blender Net Production Product: Total Finished Petroleum Products Liquefied Refinery Gases Ethane/Ethylene Ethane Ethylene Propane/Propylene Propane Propylene Normal Butane/Butylene Normal Butane Butylene Isobutane/Isobutylene Isobutane Isobutylene Finished Motor Gasoline Reformulated Gasoline Reformulated Blended w/ Fuel Ethanol Reformulated Other Gasoline Conventional Gasoline Conventional Blended w/ Fuel Ethanol Conventional Blended w/ Fuel Ethanol, Ed55 and Lower Conventional Blended w/ Fuel Ethanol, Greater than Ed55 Conventional Other Finished Aviation Gasoline Kerosene-Type Jet Fuel Kerosene Distillate Fuel Oil Distillate F.O., 15 ppm Sulfur and under Distillate F.O., Greater than 15 ppm to 500 ppm Sulfur Distillate F.O., Greater than 500 ppm Sulfur Residual Fuel Oil Residual Fuel Less Than 0.31 Percent Sulfur Residual Fuel 0.31 to 1.00 Percent Sulfur Residual Fuel Greater Than 1.00 Percent Sulfur Petrochemical Feedstocks Naphtha For Petro. Feed. Use Other Oils For Petro. Feed. Use Special Naphthas Lubricants Waxes Petroleum Coke Marketable Petroleum Coke Catalyst Petroleum Coke Asphalt and Road Oil Still Gas Miscellaneous Products Processing Gain(-) or Loss(+) Period-Unit: Monthly-Thousand Barrels Monthly-Thousand Barrels per Day Annual-Thousand Barrels Annual-Thousand Barrels per Day

82

Soap Manufacturing TechnologyChapter 11 Bar Soap Finishing  

Science Conference Proceedings (OSTI)

Soap Manufacturing Technology Chapter 11 Bar Soap Finishing Surfactants and Detergents eChapters Surfactants - Detergents Press Downloadable pdf of\tChapter 11 Bar Soap Finishing from ...

83

Motor/generator - Energy Innovation Portal  

A motor/generator is provided for connecting between a transmission input shaft and an output shaft of a prime mover. The motor/generator may include a motor ...

84

Plutonium Finishing Plant safety evaluation report  

SciTech Connect

The Plutonium Finishing Plant (PFP) previously known as the Plutonium Process and Storage Facility, or Z-Plant, was built and put into operation in 1949. Since 1949 PFP has been used for various processing missions, including plutonium purification, oxide production, metal production, parts fabrication, plutonium recovery, and the recovery of americium (Am-241). The PFP has also been used for receipt and large scale storage of plutonium scrap and product materials. The PFP Final Safety Analysis Report (FSAR) was prepared by WHC to document the hazards associated with the facility, present safety analyses of potential accident scenarios, and demonstrate the adequacy of safety class structures, systems, and components (SSCs) and operational safety requirements (OSRs) necessary to eliminate, control, or mitigate the identified hazards. Documented in this Safety Evaluation Report (SER) is DOE`s independent review and evaluation of the PFP FSAR and the basis for approval of the PFP FSAR. The evaluation is presented in a format that parallels the format of the PFP FSAR. As an aid to the reactor, a list of acronyms has been included at the beginning of this report. The DOE review concluded that the risks associated with conducting plutonium handling, processing, and storage operations within PFP facilities, as described in the PFP FSAR, are acceptable, since the accident safety analyses associated with these activities meet the WHC risk acceptance guidelines and DOE safety goals in SEN-35-91.

Not Available

1995-01-01T23:59:59.000Z

85

Metal Finishing: A Small-business Guide  

Science Conference Proceedings (OSTI)

Many of the challenges faced by small business owners can be addressed through efficient use of electric technology. Each volume in the Small-business Guide describes the current state of a business type and details new or alternative electric equipment that can help it meet its characteristic problems. The "Metal Finishing" guide is intended to familiarize readers with the business of metal finishing by providing descriptions of basic processes and practices and summaries of the key challenges faced by ...

1997-03-27T23:59:59.000Z

86

Electric Motors and Power Quality Disturbances  

Science Conference Proceedings (OSTI)

Electric motors and motor-driven systems form the backbone of the industrial sector, but these systems are susceptible to several power quality-related problems. Unbalanced voltages; voltage sags, swells, and interruptions; and overvoltages or undervoltages can cause havoc with motors, including premature motor failure from increased heating, motor inefficiency, poor power factor, and decreased starting and fullload torques. Because motor failures often result in loss of revenue, industries need to take ...

2011-12-30T23:59:59.000Z

87

motor | OpenEI  

Open Energy Info (EERE)

0 0 Varnish cache server Browse Upload data GDR 429 Throttled (bot load) Error 429 Throttled (bot load) Throttled (bot load) Guru Meditation: XID: 2142279950 Varnish cache server motor Dataset Summary Description The data included in this submission is United States Department of Transportation (DOT) data up to 1995. The data includes motor-fuel gallonage taxes 1950-1995, motor-fuel use 1919-1995, private and commercial highway use of special fuels, by state 1949-1995, highway use of gasoline, by state 1949-1995, gasohol sales by state, 1980-1992, and estimated use of gasohol, 1993-1995. The data is presented in .xlsx format. Source DOT Date Released Unknown Date Updated Unknown Keywords DOT Fuel highway motor vehicle Data application/vnd.openxmlformats-officedocument.spreadsheetml.sheet icon Motor-fuel gallonage taxes 1950-1995 (xlsx, 37.3 KiB)

88

motor vehicles | OpenEI  

Open Energy Info (EERE)

motor vehicles motor vehicles Dataset Summary Description The data included in this submission is United States Department of Transportation (DOT) data on rates and revenue statistics up to 1995. The data includes state motor-fuel tax receipts, 1919-1995, state motor fuel taxes and related receipts, 1950-1995, and state and federal motor fuel tax rates, 1919-1995 The data is presented in .xlsx format. Source DOT Date Released Unknown Date Updated Unknown Keywords DOT highway motor vehicles rates revenues Data application/vnd.openxmlformats-officedocument.spreadsheetml.sheet icon State motor-fuel tax receipts, 1919-1995 (xlsx, 13.8 KiB) application/vnd.openxmlformats-officedocument.spreadsheetml.sheet icon State motor fuel taxes and related receipts, 1950-1995 (xlsx, 78.5 KiB)

89

Parametric electric motor study  

DOE Green Energy (OSTI)

Technology for the axial gap motor was developed by DOE with an investment of approximately $15 million. This development effort is for motor technologies of high power density and high efficiency. Such motors that are also small and light-weight are not available on the commercial market because high-power motors have typically been used in large industrial applications where small size and light weight are not requirements. AC Delco has been developing motors since 1918 and is interested in leveraging its research and development dollars to produce an array of motor systems for vehicles and to develop a future line of propulsion products. The DOE focus of the study was applied to machining applications. The most attractive feature of this motor is the axial air gap, which may make possible the removal of the motor`s stationary component from a total enclosure of the remainder of the machine if the power characteristics are adequate. The objectives of this project were to evaluate alternative electric drive systems for machine tools and automotive electric drive systems and to select a best machine type for each of those applications. A major challenge of this project was to produce a small, light-weight, highly efficient motor at a cost-effective price. The project developed machine and machine drive systems and design criteria for the range of applications. The final results included the creation of a baseline for developing electric vehicle powertrain system designs, conventional vehicle engine support system designs, and advanced machine tool configurations. In addition, an axial gap permanent magnet motor was built and tested, and gave, said one engineer involved, a sterling performance. This effort will commercialize advanced motor technology and extend knowledge and design capability in the most efficient electric machine design known today.

Adams, D. [Lockheed Martin Energy Systems, Inc., Oak Ridge, TN (United States); Stahura, D. [GM-AC Delco Systems, Indianapolis, IN (United States)

1995-04-30T23:59:59.000Z

90

Control of Dimensions, Finish, and Weight  

Science Conference Proceedings (OSTI)

...The breaker cam shown in Fig. 7 was made of 3.25/3.18 mm (0.128/0.125 in.) thick 1010 cold-rolled special-killed steel. Strips 86 mm (3 in.) wide and 2.4 m (96 in.) long with a maximum hardness of 65 HRB and a No. 2 bright finish were purchased....

91

A Marketing Guide for Metal Finishing  

Science Conference Proceedings (OSTI)

Small-business strategy is among the important issues energy suppliers are considering as deregulation approaches. Businesses engaged in metal finishing constitute a priority customer segment for many utilities. Success in retaining these customers, by delivering valued services, demands in-depth knowledge of their business issues and assistance needs.

1999-05-25T23:59:59.000Z

92

A Novel Approach to Determining Motor Load  

E-Print Network (OSTI)

Properly sized electric motors are essential if industrial plant efficiency is to be optimized and energy costs minimized. Because of the difficulty in making power measurements on three phase motors, loading is rarely, if ever, checked. A simple indication of motor load can be achieved by measuring operating speed because speed and load are almost linearly related. The decrease in motor speed from no load conditions, referred to as slip, can be determined with a non-contact, optical tachometer. Field measurements of motor slip were conducted at a textile plant to quantify motor load conditions. To verify the relationship between operating speed and load, measurements of motor power consumption on a representative number of motors were also conducted. The results of the motor survey, including number of motors, size, and load, are summarized in this paper along with an estimate of the savings from replacing oversized motors.

Brown, M.

1992-04-01T23:59:59.000Z

93

Automation in modeling: using automation for finishing room capacity planning  

Science Conference Proceedings (OSTI)

Capacity planning of a furniture finishing system using both deterministic analysis and stochastic simulation is conveniently performed with the aid ActiveX Automation. Users interactively build a complete model of a finishing system with an Excel interface, ...

Ryan Heath Melton; C. Thomas Culbreth; Stephen D. Roberts; Jeffrey A. Joines

2001-12-01T23:59:59.000Z

94

Independent Activity Report, Hanford Plutonium Finishing Plant- May 2012  

Energy.gov (U.S. Department of Energy (DOE))

Criticality Safety Information Meeting for the Hanford Plutonium Finishing Plant [HIAR-RL-2012-05-14

95

Nearly Finished Genomes Produced Using Gel Microdroplet Culturing (Seventh Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting 2012)  

Science Conference Proceedings (OSTI)

Michael Fitzsimmons from Los Alamos National Laboratory gives a talk titled "Nearly Finished Genomes Produced Using Gel Microdroplet Culturing" at the 7th Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting held in June, 2012 in Santa Fe, NM.

Fitzsimmons, Michael [LANL

2012-06-01T23:59:59.000Z

96

Universal adaptive torque control for PM motors for field ...  

The invention includes a motor controller and method for controlling a permanent magnet motor. In accordance with one aspect of the present technique, a permanent ...

97

Department of Electrical Engineering Fall 2009 Electridyne Motor  

E-Print Network (OSTI)

PENNSTATE Department of Electrical Engineering Fall 2009 Electridyne Motor Overview Our sponsored project was to design an elecrtic motor for an urban transportation vehicle, the challenges involved included research into motor design, consideration of the materials, and the electromagnetic parameters

Demirel, Melik C.

98

Self-bearing motor design & control  

E-Print Network (OSTI)

This thesis presents the design, implementation and control of a new class of self-bearing motors. The primary thesis contributions include the design and experimental demonstration of hysteresis self-bearing motors, novel ...

Imani Nejad, Mohammad

2013-01-01T23:59:59.000Z

99

Plasma technology for textile finishing applications gets a boost from LANL  

NLE Websites -- All DOE Office Websites (Extended Search)

Plasma technology for textile finishing applications gets a boost Plasma technology for textile finishing applications gets a boost from LANL Plasma technology for textile finishing applications gets a boost from LANL APJeT received a $100,000 Venture Acceleration Fund award from LANS helping to complete design and engineering of a commercial-scale production unit. April 3, 2012 image description Gary Selwyn conducts product quality assurance on dual-functional, plasma-treated fabric at APJeT's Santa Fe lab: LANL technology may transform performance apparel. Contact CEO John Emrich (505) 471-6399 Future applications of APJet may include depositing thin films for architectural glass, semiconductors, flooring, and solar panels. "A big part of our current challenge has been selecting this one use for the technology and putting all of our energy and resources into that," Selwyn

100

Green Racing - Where Clean Cars Finish First  

NLE Websites -- All DOE Office Websites (Extended Search)

Technology Technology R&D Center INVENTING THE FUTURE. efficient. clean. safe. Green Racing Where Clean Cars Finish First In green racing, speed is a factor, but the overall winner is determined by a formula that also takes the car's environmental footprint into consideration. Race organizers calculated a principal component of each car's score by using Argonne's Greenhouse gas, Regulated Emissions, and Energy use in Transportation (GREET) model. Research funding provided by the U.S. Department of Energy's Vehicle Technologies Program. Did you know... Opportunity The racetrack is a proving ground that often leads to innovations in consumer vehicles. Green

Note: This page contains sample records for the topic "includes finished motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Plutonium Finishing Plant (PFP) HVAC System Component Index  

Science Conference Proceedings (OSTI)

The Plutonium Finishing Plant (PFP) WAC System includes sub-systems 25A through 25K. Specific system boundaries and justifications are contained in HNF-SD-CP-SDD-005, ''Definition and Means of Maintaining the Ventilation System Confinement Portion of the PFP Safety Envelope.'' The procurement requirements associated with the system necessitates procurement of some system equipment as Commercial Grade Items in accordance with HNF-PRO-268, ''Control of Purchased Items and Services.'' This document lists safety class and safety significant components for the Heating Ventilation Air Conditioning and specifies the critical characteristics for Commercial Grade Items, as required by HNF-PRO-268 and HNF-PRO-1819. These are the minimum specifications that the equipment must meet in order to properly perform its safety function. There may be several manufacturers or models that meet the critical characteristics for any one item.

DICK, J.D.

2000-02-28T23:59:59.000Z

102

Plutonium Finishing Plant (PFP) HVAC System Component Index  

SciTech Connect

This document lists safety class (SC) and safety significant (SS) components for the Heating Ventilation Air Conditioning (HVAC) and specifies the critical characteristics for Commercial Grade Items (CGI), as required by HNF-PRO-268 and HNF-PRO-18 19. These are the minimum specifications that the equipment must meet in order to properly perform its safety function. There may be several manufacturers or models that meet the critical characteristics for any one item. The Plutonium Finishing Plant (PFP) HVAC System includes sub-systems 25A through 25K. Specific system boundaries and justifications are contained in HNF-SD-CP-SDD-005, ''Definition and Means of Maintaining the Ventilation System Confinement Portion of the PFP Safety Envelope.'' The procurement requirements associated with the system necessitates procurement of some system equipment as Commercial Grade Items in accordance with HNF-PRO-268, ''Control of Purchased Items and Services.''

DIAZ, E.N.

2000-03-30T23:59:59.000Z

103

System and method for motor speed estimation of an electric motor  

DOE Patents (OSTI)

A system and method for a motor management system includes a computer readable storage medium and a processing unit. The processing unit configured to determine a voltage value of a voltage input to an alternating current (AC) motor, determine a frequency value of at least one of a voltage input and a current input to the AC motor, determine a load value from the AC motor, and access a set of motor nameplate data, where the set of motor nameplate data includes a rated power, a rated speed, a rated frequency, and a rated voltage of the AC motor. The processing unit is also configured to estimate a motor speed based on the voltage value, the frequency value, the load value, and the set of nameplate data and also store the motor speed on the computer readable storage medium.

Lu, Bin (Kenosha, WI); Yan, Ting (Brookfield, WI); Luebke, Charles John (Sussex, WI); Sharma, Santosh Kumar (Viman Nagar, IN)

2012-06-19T23:59:59.000Z

104

Motorized control for mirror mount apparatus  

DOE Patents (OSTI)

A motorized control and automatic braking system for adjusting mirror mount apparatus is disclosed. The motor control includes a planetary gear arrangement to provide improved pitch adjustment capability while permitting a small packaged design. The motor control for mirror mount adjustment is suitable for laser beam propagation applications. The brake is a system of constant contact, floating detents which engage the planetary gear at selected between-teeth increments to stop rotation instantaneously when the drive motor stops.

Cutburth, Ronald W. (Tracy, CA)

1989-01-01T23:59:59.000Z

105

Advanced Electric Motor Predictive Maintenance Project  

Science Conference Proceedings (OSTI)

EPRI sponsored the three-year Advanced Electric Motor Predictive Maintenance (AEMPM) project in 2000 to increase the effectiveness of motor maintenance at a time when utilities were in a state of declining motor knowledge due to downsizing and restructuring. The project identified areas for improvement that were common to most utilities and selected appropriate measures to address these concerns. Areas addressed include documenting motor knowledge, increasing utility confidence in newer technologies and ...

2003-05-28T23:59:59.000Z

106

Figure and finish of grazing incidence mirrors  

SciTech Connect

Great improvement has been made in the past several years in the quality of optical components used in synchrotron radiation (SR) beamlines. Most of this progress has been the result of vastly improved metrology techniques and instrumentation permitting rapid and accurate measurement of the surface finish and figure on grazing incidence optics. A significant theoretical effort has linked the actual performance of components used as x-ray wavelengths to their topological properties as measured by surface profiling instruments. Next-generation advanced light sources will require optical components and systems to have sub-arc second surface figure tolerances. This paper will explore the consequences of these requirements in terms of manufacturing tolerances to see if the present manufacturing state-of-the-art is capable of producing the required surfaces. 15 refs., 14 figs., 2 tabs.

Takacs, P.Z. (Brookhaven National Lab., Upton, NY (USA)); Church, E.L. (Picatinny Arsenal, Dover, NJ (USA). Army Armament Research, Development and Engineering Center)

1989-08-01T23:59:59.000Z

107

Advanced Motors  

SciTech Connect

Project Summary Transportation energy usage is predicted to increase substantially by 2020. Hybrid vehicles and fuel cell powered vehicles are destined to become more prominent as fuel prices rise with the demand. Hybrid and fuel cell vehicle platforms are both dependent on high performance electric motors. Electric motors for transportation duty will require sizeable low-speed torque to accelerate the vehicle. As motor speed increases, the torque requirement decreases which results in a nearly constant power motor output. Interior permanent magnet synchronous motors (IPMSM) are well suited for this duty. , , These rotor geometries are configured in straight lines and semi circular arc shapes. These designs are of limited configurations because of the lack of availability of permanent magnets of any other shapes at present. We propose to fabricate rotors via a novel processing approach where we start with magnet powders and compact them into a net shape rotor in a single step. Using this approach, widely different rotor designs can be implemented for efficiency. The current limitation on magnet shape and thickness will be eliminated. This is accomplished by co-filling magnet and soft iron powders at specified locations in intricate shapes using specially designed dies and automatic powder filling station. The process fundamentals for accomplishing occurred under a previous Applied Technology Program titled, ???????????????¢????????????????????????????????Motors and Generators for the 21st Century???????????????¢???????????????????????????????. New efficient motor designs that are not currently possible (or cost prohibitive) can be accomplished by this approach. Such an approach to motor fabrication opens up a new dimension in motor design. Feasibility Results We were able to optimize a IPMSM rotor to take advantage of the powder co-filling and DMC compaction processing methods. The minimum low speed torque requirement of 5 N-m can be met through an optimized design with magnet material having a Br capability of 0.2 T. This level of magnetic performance can be met with a variety of bonded magnet compositions. The torque ripple was found to drop significantly by using thinner magnet segments. The powder co-filling and subsequent compaction processing allow for thinner magnet structures to be formed. Torque ripple can be further reduced by using skewing and pole shaping techniques. The techniques can be incorporated into the rotor during the powder co-filling process.

Knoth, Edward A.; Chelluri, Bhanumathi; Schumaker, Edward J.

2012-12-14T23:59:59.000Z

108

Segmented rail linear induction motor  

DOE Patents (OSTI)

A segmented rail linear induction motor has a segmented rail consisting of a plurality of nonferrous electrically conductive segments aligned along a guideway. The motor further includes a carriage including at least one pair of opposed coils fastened to the carriage for moving the carriage. A power source applies an electric current to the coils to induce currents in the conductive surfaces to repel the coils from adjacent edges of the conductive surfaces.

Cowan, Jr., Maynard (1107 Stagecoach Rd. SE., Albuquerque, NM 87123); Marder, Barry M. (1412 Pinnacle View Dr. NE., Albuquerque, NM 87123)

1996-01-01T23:59:59.000Z

109

Segmented rail linear induction motor  

DOE Patents (OSTI)

A segmented rail linear induction motor has a segmented rail consisting of a plurality of nonferrous electrically conductive segments aligned along a guideway. The motor further includes a carriage including at least one pair of opposed coils fastened to the carriage for moving the carriage. A power source applies an electric current to the coils to induce currents in the conductive surfaces to repel the coils from adjacent edges of the conductive surfaces. 6 figs.

Cowan, M. Jr.; Marder, B.M.

1996-09-03T23:59:59.000Z

110

Reduced vibration motor winding arrangement - Energy ...  

An individual phase winding arrangement having a sixty electrical degree phase belt width for use with a three phase motor armature includes a delta connected phase ...

111

Automatic tool path generation for finish machining  

SciTech Connect

A system for automatic tool path generation was developed at Sandia National Laboratories for finish machining operations. The system consists of a commercially available 5-axis milling machine controlled by Sandia developed software. This system was used to remove overspray on cast turbine blades. A laser-based, structured-light sensor, mounted on a tool holder, is used to collect 3D data points around the surface of the turbine blade. Using the digitized model of the blade, a tool path is generated which will drive a 0.375 inch diameter CBN grinding pin around the tip of the blade. A fuzzified digital filter was developed to properly eliminate false sensor readings caused by burrs, holes and overspray. The digital filter was found to successfully generate the correct tool path for a blade with intentionally scanned holes and defects. The fuzzified filter improved the computation efficiency by a factor of 25. For application to general parts, an adaptive scanning algorithm was developed and presented with simulation results. A right pyramid and an ellipsoid were scanned successfully with the adaptive algorithm.

Kwok, Kwan S.; Loucks, C.S.; Driessen, B.J.

1997-03-01T23:59:59.000Z

112

State observer for synchronous motors  

DOE Patents (OSTI)

A state observer driven by measurements of phase voltages and currents for estimating the angular orientation of a rotor of a synchronous motor such as a variable reluctance motor (VRM). Phase voltages and currents are detected and serve as inputs to a state observer. The state observer includes a mathematical model of the electromechanical operation of the synchronous motor. The characteristics of the state observer are selected so that the observer estimates converge to the actual rotor angular orientation and velocity, winding phase flux linkages or currents.

Lang, Jeffrey H. (Waltham, MA)

1994-03-22T23:59:59.000Z

113

Not a Babe in the Woods: Using MotorMaster Software to Make Sophisticated Electric Motor Purchase Decisions  

E-Print Network (OSTI)

Three-phase motors use more than half of all electricity in the United States. Energy efficient models are available in most motor classes in the 1 to 500 horsepower range, offering simple pay backs under two years. In practice, few motor buyers have performed an economic analysis, resulting in missed energy and dollar savings. MotorMaster software helps identify the best motor for a specific application. Its database of 9,000 motors includes the majority of three-phase motors sold in the United State. Performance information such as Full-Load RPM, torque and amperage rating identify models that meet specific design criteria. MotorMaster calculates operating costs and simple paybacks. This paper reviews the importance of proper electric motor selection and explains how MotorMaster software can be used to identify the most efficient, cost effective and reliable motor for each specific application.

Litman, T.

1993-03-01T23:59:59.000Z

114

Rotary steerable motor system for underground drilling  

Science Conference Proceedings (OSTI)

A preferred embodiment of a system for rotating and guiding a drill bit in an underground bore includes a drilling motor and a drive shaft coupled to drilling motor so that drill bit can be rotated by the drilling motor. The system further includes a guidance module having an actuating arm movable between an extended position wherein the actuating arm can contact a surface of the bore and thereby exert a force on the housing of the guidance module, and a retracted position.

Turner, William E. (Durham, CT); Perry, Carl A. (Middletown, CT); Wassell, Mark E. (Kingwood, TX); Barbely, Jason R. (Middletown, CT); Burgess, Daniel E. (Middletown, CT); Cobern, Martin E. (Cheshire, CT)

2010-07-27T23:59:59.000Z

115

Direct drive field actuator motors  

DOE Patents (OSTI)

A positive-drive field actuator motor is described which includes a stator carrying at least one field actuator which changes in dimension responsive to application of an energy field, and at least one drive shoe movable by the dimensional changes of the field actuator to contact and move a rotor element with respect to the stator. Various embodiments of the motor are disclosed, and the rotor element may be moved linearly or arcuately. 62 figs.

Grahn, A.R.

1998-03-10T23:59:59.000Z

116

Final Environmental Impact Statement - Plutonium Finishing Plant Stabilization, May 1996  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

- Plutonium Finishing Plant Stabilization, May 1996 - Plutonium Finishing Plant Stabilization, May 1996 file:///I|/Data%20Migration%20Task/EIS-0244-FEIS-1996/eis0244f_1.html[6/27/2011 2:33:34 PM] 1.0 INTRODUCTION This Introduction contains the following information: Background of the Plutonium Finishing Plant Facility Scope of this Environmental Impact Statement Contents of this Environmental Impact Statement The presence of significant quantities of plutonium-bearing materials in the Plutonium Finishing Plant (PFP) Facility, Hanford Site, Washington, poses unacceptable risks to workers, the public, and the environment. On October 24, 1994, the United States Department of Energy (DOE) announced, in an initial mailing to 1,500 interested parties, its intent to prepare an Environmental Impact Statement (EIS) pursuant to the National

117

U.S. Exports of Finished Petroleum Products (Thousand ...  

U.S. Energy Information Administration (EIA)

U.S. Exports of Finished Petroleum Products (Thousand Barrels per Day) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov ... U.S. Exports of Crude Oil ...

118

Oak Ridge Finishes Site's Largest Demolition Project to Date | Department  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Finishes Site's Largest Demolition Project to Date Finishes Site's Largest Demolition Project to Date Oak Ridge Finishes Site's Largest Demolition Project to Date July 1, 2012 - 12:00pm Addthis BEFORE: An aerial photo shows Building K-33 before demolition. BEFORE: An aerial photo shows Building K-33 before demolition. AFTER: This photo shows the site of Building K-33 following completion of the demolition project. AFTER: This photo shows the site of Building K-33 following completion of the demolition project. BEFORE: An aerial photo shows Building K-33 before demolition. AFTER: This photo shows the site of Building K-33 following completion of the demolition project. OAK RIDGE, Tenn. - This month, the Oak Ridge Environmental Management (EM) program finished the final phase of the Building K-33 demolition

119

Submersible canned motor mixer pump  

DOE Patents (OSTI)

A mixer pump used in a waste tank for mobilizing high-level radioactive liquid waste having a column assembly containing power cables, a motor housing with electric motor means which includes a stator can of a stator assembly and a rotor can of a rotor assembly, and an impeller assembly with an impeller connected to a shaft of the rotor assembly. The column assembly locates the motor housing with the electric motor means adjacent to the impeller which creates an hydraulic head, and which forces the liquid waste into the motor housing to cool the electric motor means and to lubricate radial and thrust bearing assemblies. Hard-on-hard bearing surfaces of the bearing assemblies and a ring assembly between the impeller and electric motor means act to grind down large particles in the liquid waste flow. These larger particles are received in slots in the static bearing members of the radial bearing assemblies. Only solid waste particles smaller than the clearances in the system can pass therethrough, thereby resisting damage to and the interruption of the operation of the mixer pump.

Guardiani, Richard F. (Ohio Township, PA); Pollick, Richard D. (Sarver, PA)

1997-01-01T23:59:59.000Z

120

Submersible canned motor mixer pump  

DOE Patents (OSTI)

A mixer pump is described used in a waste tank for mobilizing high-level radioactive liquid waste having a column assembly containing power cables, a motor housing with electric motor means which includes a stator can of a stator assembly and a rotor can of a rotor assembly, and an impeller assembly with an impeller connected to a shaft of the rotor assembly. The column assembly locates the motor housing with the electric motor means adjacent to the impeller which creates an hydraulic head, and which forces the liquid waste into the motor housing to cool the electric motor means and to lubricate radial and thrust bearing assemblies. Hard-on-hard bearing surfaces of the bearing assemblies and a ring assembly between the impeller and electric motor means act to grind down large particles in the liquid waste flow. These larger particles are received in slots in the static bearing members of the radial bearing assemblies. Only solid waste particles smaller than the clearances in the system can pass there through, thereby resisting damage to and the interruption of the operation of the mixer pump. 10 figs.

Guardiani, R.F.; Pollick, R.D.

1997-10-07T23:59:59.000Z

Note: This page contains sample records for the topic "includes finished motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

MotorMaster+ International  

NLE Websites -- All DOE Office Websites (Extended Search)

Motors with MotorMaster+ International * Are your plant motor systems running at optimal energy efficiency? * Do you know how to cost-effectively determine whether to repair or...

122

System and method for determining stator winding resistance in an AC motor using motor drives  

DOE Patents (OSTI)

A system and method for determining the stator winding resistance of AC motors is provided. The system includes an AC motor drive having an input connectable to an AC source and an output connectable to an input terminal of an AC motor, a pulse width modulation (PWM) converter having switches therein to control current flow and terminal voltages in the AC motor, and a control system connected to the PWM converter. The control system generates a command signal to cause the PWM converter to control an output of the AC motor drive corresponding to an input to the AC motor, selectively generates a modified command signal to cause the PWM converter to inject a DC signal into the output of the AC motor drive, and determines a stator winding resistance of the AC motor based on the DC signal of at least one of the voltage and current.

Lu, Bin; Habetler, Thomas G; Zhang, Pinjia

2013-02-26T23:59:59.000Z

123

Motor gasolines, Summer 1982  

Science Conference Proceedings (OSTI)

The samples were collected from service stations throughout the country and were analyzed in the laboratories of various refiners, motor manufacturers, and chemical companies. The analytical data for 796 samples of motor gasoline, were submitted to the Bartlesville Energy Technology Center for study, necessary calculations, and compilation under a cooperative agreement between the Bartlesville Energy Technology Center (BETC) and the American Petroleum Institute (API). They represent the products of 22 companies, large and small, which manufacture and supply gasoline. These data are tabulated by groups according to brands (unlabeled) and grades for 17 marketing districts into which the country is divided. A map included in this report, shows marketing areas, districts and sampling locations. The report also includes charts indicating the trends of selected properties of motor fuels since 1959. Sixteen octane distribution percent charts for areas 1, 2, 3, and 4 for unleaded antiknock index (R + M)/2 below 90.0, unleaded antiknock index (R + M)/2 90.0 and above, leaded antiknock index (R + M)/2 below 93.0, and leaded antiknock index (R + M)/2 93.0 and above grades of gasoline are presented in this report. The antiknock (octane) index (R + M)/2 averages of gasoline sold in this country were 87.3 for unleaded below 90.0, 91.7 for unleaded 90.0 and above, 89.0 for leaded below 93.0, and no data in this report for 93.0 and above grades of leaded gasoline.

Shelton, E.M.

1983-03-01T23:59:59.000Z

124

TFTR Motor Generator  

SciTech Connect

A general description is given of 475 MVA pulsed motor generators for TFTR at Princeton Plasma Physics Laboratory. Two identical generators operating in parallel are capable of supplying 950 MVA for an equivalent square pulse of 6.77 seconds and 4,500 MJ at 0.7 power factor to provide the energy for the pulsed electrical coils and heating system for TFTR. The description includes the operational features of the 15,000 HP wound rotor motors driving each generator with its starting equipment and cycloconverter for controlling speed, power factor, and regulating line voltage during load pulsing where the generator speed changes from 87.5 to 60 Hz frequency variation to provide the 4,500 MJ or energy. The special design characteristics such as fatigue stress calculations for 10/sup 6/ cycles of operation, forcing factor on exciter to provide regulation, and low generator impedance are reviewed.

Murray, J.G.; Bronner, G.; Horton, M.

1977-01-01T23:59:59.000Z

125

Electrical system for a motor vehicle  

DOE Patents (OSTI)

In one embodiment of the present invention, an electrical system for a motor vehicle comprises a capacitor, an engine cranking motor coupled to receive motive power from the capacitor, a storage battery and an electrical generator having an electrical power output, the output coupled to provide electrical energy to the capacitor and to the storage battery. The electrical system also includes a resistor which limits current flow from the battery to the engine cranking motor. The electrical system further includes a diode which allows current flow through the diode from the generator to the battery but which blocks current flow through the diode from the battery to the cranking motor. 2 figs.

Tamor, M.A.

1999-07-20T23:59:59.000Z

126

Electrical system for a motor vehicle  

SciTech Connect

In one embodiment of the present invention, an electrical system for a motor vehicle comprises a capacitor, an engine cranking motor coupled to receive motive power from the capacitor, a storage battery and an electrical generator having an electrical power output, the output coupled to provide electrical energy to the capacitor and to the storage battery. The electrical system also includes a resistor which limits current flow from the battery to the engine cranking motor. The electrical system further includes a diode which allows current flow through the diode from the generator to the battery but which blocks current flow through the diode from the battery to the cranking motor.

Tamor, Michael Alan (Toledo, OH)

1999-01-01T23:59:59.000Z

127

Price of Motor Gasoline Through Retail Outlets  

Gasoline and Diesel Fuel Update (EIA)

Prices, Sales Volumes & Stocks by State Prices, Sales Volumes & Stocks by State (Dollars per Gallon Excluding Taxes) Data Series: Retail Price - Motor Gasoline Retail Price - Regular Gasoline Retail Price - Midgrade Gasoline Retail Price - Premium Gasoline Retail Price - Aviation Gasoline Retail Price - Kerosene-Type Jet Fuel Retail Price - Propane Retail Price - Kerosene Retail Price - No. 1 Distillate Retail Price - No. 2 Distillate Retail Price - No. 2 Fuel Oil Retail Price - No. 2 Diesel Fuel Retail Price - No. 4 Fuel Oil Prime Supplier Sales - Motor Gasoline Prime Supplier Sales - Regular Gasoline Prime Supplier Sales - Midgrade Gasoline Prime Supplier Sales - Premium Gasoline Prime Supplier Sales - Aviation Gasoline Prime Supplier Sales - Kerosene-Type Jet Fuel Prime Supplier Sales - Propane (Consumer Grade) Prime Supplier Sales - Kerosene Prime Supplier Sales - No. 1 Distillate Prime Supplier Sales - No. 2 Distillate Prime Supplier Sales - No. 2 Fuel Oil Prime Supplier Sales - No. 2 Diesel Fuel Prime Supplier Sales - No. 4 Fuel Oil Prime Supplier Sales - Residual Fuel Oil Stocks - Finished Motor Gasoline Stocks - Reformulated Gasoline Stocks - Conventional Gasoline Stocks - Motor Gasoline Blending Components Stocks - Kerosene Stocks - Distillate Fuel Oil Stocks - Distillate F.O., 15 ppm and under Sulfur Stocks - Distillate F.O., Greater than 15 to 500 ppm Sulfur Stocks - Distillate F.O., Greater 500 ppm Sulfur Stocks - Residual Fuel Oil Stocks - Propane/Propylene Period: Monthly Annual

128

Finished Prokaryotic Genome Assemblies from a Low-cost Combination of Short and Long Reads (Seventh Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting 2012)  

Science Conference Proceedings (OSTI)

Shuangye Yin on "Finished prokaryotic genome assemblies from a low-cost combination of short and long reads" at the 2012 Sequencing, Finishing, Analysis in the Future Meeting held June 5-7, 2012 in Santa Fe, New Mexico.

Yin, Shuangye (Broad Institute)

2012-06-01T23:59:59.000Z

129

Rare-Earth-Free Traction Motor: Rare Earth-Free Traction Motor for Electric Vehicle Applications  

Science Conference Proceedings (OSTI)

REACT Project: Baldor will develop a new type of traction motor with the potential to efficiently power future generations of EVs. Unlike todays large, bulky EV motors which use expensive, imported rare-earth-based magnets, Baldors motor could be light, compact, contain no rare earth materials, and have the potential to deliver more torque at a substantially lower cost. Key innovations in this project include the use of a unique motor design, incorporation of an improved cooling system, and the development of advanced materials manufacturing techniques. These innovations could significantly reduce the cost of an electric motor.

None

2012-01-01T23:59:59.000Z

130

U.S. Ending Stocks of Finished Motor Gasoline (Thousand Barrels)  

U.S. Energy Information Administration (EIA)

Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec; 1981: 226,603: 229,921: 232,430: 223,352: 212,683: 194,008: 185,703: 188,643: 190,731: 190,500: 200,643: 203,469 ...

131

U.S. Imports of Finished Motor Gasoline (Thousand Barrels per Day)  

U.S. Energy Information Administration (EIA)

Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec; 1945: 5: 7: 4: 3: 10: 12: 5: 7: 2: 3: 3: 0: 1946: 0: 0: 0: 0: 0: 0: 0: 0: 0: 0: 0: 0: 1947: 0: 0: 0: 0: 0: 3: 0 ...

132

U.S. Exports of Finished Motor Gasoline (Thousand Barrels per Day)  

U.S. Energy Information Administration (EIA)

Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9; 1930's: 84: 78: 105: 137: 122: 1940's: 69: 74: 96: 141: 275: 241: 124: 130: 102: 108 ...

133

Net Imports of Finished Motor Gasoline into the U.S. by Country  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: *Countries listed under ...

134

4-Week Avg U.S. Product Supplied of Finished Motor Gasoline ...  

U.S. Energy Information Administration (EIA)

Year-Month Week 1 Week 2 Week 3 Week 4 Week 5; End Date Value End Date Value End Date Value End Date Value End Date Value; 1991-Mar : 03/08 : 6,779 : 03/15 : 6,907

135

U.S. Imports of Finished Motor Gasoline (Thousand Barrels per Day)  

U.S. Energy Information Administration (EIA)

Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9; 1930's: 0: 0: 0: 0: 0: 1940's: 0: 1: 0: 16: 9: 5: 0: 1: 1: 0: 1950's: 0: 1: 5: 1: 3: 13 ...

136

32904,"AECTRA REFG & MKTG",1,133,"MOTOR GAS, FINISHED UNLEADED...  

U.S. Energy Information Administration (EIA) Indexed Site

BUTANENGL",3901,"CHICAGO, IL","ILLINOIS",2,260,"CANADA",1,0,0,,,,, 32904,"ALPENA OIL CO INC",1,411,"DISTILLATE FUEL, TOTAL",3843,"ALPENA, MI","MICHIGAN",2,260,"CANADA",40,0...

137

U.S. Exports to Indonesia of Finished Motor Gasoline (Thousand ...  

U.S. Energy Information Administration (EIA)

Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9; 1990's: 0: 2000's: 0: 0: 2010's: 0-

138

U.S. Exports to Venezuela of Finished Motor Gasoline (Thousand ...  

U.S. Energy Information Administration (EIA)

Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9; 1990's: 0: 2: 0: 1: 0: 2000's: 0: 0: 1: 4: 0: 0: 0: 0: 0: 2010's: 0: 3: 34-

139

U.S. Product Supplied of Finished Motor Gasoline (Thousand Barrels ...  

U.S. Energy Information Administration (EIA)

Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9; 1940's: 1,587: 1,979: 2,119: 2,280: 2,410: 1950's: 2,616: 2,985: 2,954: 3,110: 3,194 ...

140

Weekly U.S. Ending Stocks of Finished Motor Gasoline (Thousand ...  

U.S. Energy Information Administration (EIA)

Year-Month Week 1 Week 2 Week 3 Week 4 Week 5; End Date Value End Date Value End Date Value End Date Value End Date Value; 1990-Jan: 01/05 : 175,009 : ...

Note: This page contains sample records for the topic "includes finished motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

31808,"AECTRA REFG & MKTG",1,133,"MOTOR GAS, FINISHED UNLEADED...  

U.S. Energy Information Administration (EIA) Indexed Site

PROCESSOR-TX","UNKNOWN PROCESSOR-TX","TX","TEXAS",3 31808,"AGWAY PETRO CORP",1,231,"PROPANENGL",0712,"CHAMPL-RS PT, NY","NEW YORK",1,260,"CANADA",3,0,0,,,,, 31808,"ALPENA OIL...

142

32173,"AECTRA REFG & MKTG",1,133,"MOTOR GAS, FINISHED UNLEADED...  

U.S. Energy Information Administration (EIA) Indexed Site

IL","ILLINOIS",2,260,"CANADA",1,0,0,,,,, 32173,"AGWAY PETRO CORP",1,231,"PROPANENGL",0712,"CHAMPL-RS PT, NY","NEW YORK",1,260,"CANADA",4,0,0,,,,, 32173,"AMERADA HESS...

143

32539,"AECTRA REFG & MKTG",1,133,"MOTOR GAS, FINISHED UNLEADED...  

U.S. Energy Information Administration (EIA) Indexed Site

TERM CO","DEER PARK","TX","TEXAS",3 32539,"AGWAY PETRO CORP",1,231,"PROPANENGL",0712,"CHAMPL-RS PT, NY","NEW YORK",1,260,"CANADA",4,0,0,,,,, 32539,"AMERADA HESS...

144

36191,"AECTRA REFG & MKTG",1,152,"MOTOR GAS, OTHER FINISHED"...  

U.S. Energy Information Administration (EIA) Indexed Site

N AMER AUTOMOTIVE INC",1,854,"LUBRICANTS, TOTAL",5301,"HOUSTON, TX","TEXAS",3,515,"KOREA, REPUBLIC OF",24,0,0 36191,"CAVALIER GAS CO",1,231,"PROPANENGL",3404,"NECHE,...

145

U.S. Imports from Korea of Finished Motor Gasoline (Thousand Barrels)  

U.S. Energy Information Administration (EIA)

Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec; 1999: 0: 0: 0: 453: 274: 0: 613: 424: 195: 0: 0: 0: 2000: 0: 160: 133: 0: 0: 0: 0: 0: 101: 0: 219: 0: 2001: 231 ...

146

33634,"AECTRA REFG & MKTG",1,133,"MOTOR GAS, FINISHED UNLEADED...  

U.S. Energy Information Administration (EIA) Indexed Site

HYDROCARBONSHYDROGENOXY, TOTAL",2709,"LONG BEACH, CA","CALIFORNIA",5,515,"KOREA, REPUBLIC OF",17,0,0,"EXXON CO USA","BENICIA","CA","CALIFORNIA",5 33634,"ITOCHU INTL...

147

33269,"AECTRA REFG & MKTG",1,133,"MOTOR GAS, FINISHED UNLEADED...  

U.S. Energy Information Administration (EIA) Indexed Site

INC",1,822,"NAPHTHA ( < 401 DEGREES F ENDPOINT)",2909,"KALAMA, WA","WASHINGTON",5,515,"KOREA, REPUBLIC OF",37,0,0,,,,, 33269,"KERR-MCGEE REFG CORP",1,820,"UNFINISHED OILS,...

148

36556,"AECTRA REFG & MKTG",1,152,"MOTOR GAS, OTHER FINISHED"...  

U.S. Energy Information Administration (EIA) Indexed Site

36556,"ALPAC MKTG SERV",1,51,"SPECIAL NAPHTHAS",5301,"HOUSTON, TX","TEXAS",3,515,"KOREA, REPUBLIC OF",88,0,0 36556,"AMERADA HESS CORP",1,461,"DISTILLATE, < 0.05% SUL...

149

35461,"AECTRA REFG & MKTG",1,152,"MOTOR GAS, OTHER FINISHED"...  

U.S. Energy Information Administration (EIA) Indexed Site

TERTIARY BUTYL ETHER (MTBE)",2809,"SANFRANCISCO, CA","CALIFORNIA",5,515,"KOREA, REPUBLIC OF",32,0,0,"WICKLAND OIL CO","SELBY TERM","CA","CALIFORNIA",5...

150

U.S. Exports to Mexico of Finished Motor Gasoline (Thousand ...  

U.S. Energy Information Administration (EIA)

75: 120: 1999: 88: 84: 65: 78: 89: 62: 77: 82: 120: 107: 115: 148: 2000: 105: 74: 78: 88: 104: 84: 95: 179: 171: 187: 155: 168: 2001: 97: 96: 121: 127: 82: 88: 107 ...

151

U.S. Exports to Mexico of Finished Motor Gasoline (Thousand ...  

U.S. Energy Information Administration (EIA)

Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9; 1990's: 58: 58: 65: 61: 90: 84: 93: 2000's: 124: 107: 108: 94: 104: 110: ...

152

The Allocation of the Social Costs of Motor-Vehicle Use to Six Classes of Motor Vehicles  

E-Print Network (OSTI)

motor gasoline was $0.957/gallon in 1987, and $1.196 in 1991, including taxes (tax price of gasoline sold by service stations owned by refining companies with the sales- weighted average retail of all motor

Delucchi, Mark A.

1996-01-01T23:59:59.000Z

153

Motor torque compensation of an induction electric motor by ...  

Motor torque compensation of an induction electric motor by adjusting a slip command during periods of supposed change in motor temperature United States Patent

154

Three phase AC motor controller  

DOE Patents (OSTI)

A motor controller for a three phase AC motor (10) which is adapted to operate bidirectionally from signals received either from a computer (30) or a manual control (32). The controller is comprised of digital logic circuit means which implement a forward and reverse command signal channel (27, 29) for the application of power through the forward and reverse power switching relays (16, 18, 20, 22). The digital logic elements are cross coupled to prevent activation of both channels simultaneously and each includes a plugging circuit (65, 67) for stopping the motor upon the removal of control signal applied to one of the two channels (27, 29) for a direction of rotation desired. Each plugging circuit (65, 67) includes a one-shot pulse signal generator (88, 102) which outputs a single pulse signal of predetermined pulsewidth which is adapted to inhibit further operation of the application of power in the channel which is being activated and to apply a reversal command signal to the other channel which provides a reversed phase application of power to the motor for a period defined by the pulse-width output of the one-shot signal generator to plug the motor (10) which will then be inoperative until another rotational command signal is applied to either of the two channels.

Vuckovich, Michael (Elizabeth, PA); Wright, Maynard K. (Bethel Park, PA); Burkett, John P. (South Huntington Township, Westmoreland County, PA)

1984-03-20T23:59:59.000Z

155

Reduced vibration motor winding arrangement  

DOE Patents (OSTI)

The present invention relates generally to an electric motor winding and, more particularly, to a three phase motor armature winding arrangement designed to reduce motor vibration and improve efficiency. An individual phase winding arrangement having a sixty electrical degree phase belt width for use with a three phase motor armature includes a delta connected phase winding portion and a wye connected phase winding portion. Both the delta and wye connected phase winding portions have a thirty electrical degree phase belt width. The delta and wye connected phase winding portions are each formed from a preselected number of individual coils each formed, in turn, from an unequal number of electrical conductor turns in the approximate ratio of {radical}3. The individual coils of the delta and wye connected phase winding portions may either be connected in series or parallel. This arrangement provides an armature winding for a three phase motor which retains the benefits of the widely known and utilized thirty degree phase belt concept, including improved mmf waveform and fundamental distribution factor.

Slavik, C.J.; Rhudy, R.G.; Bushman, R.E.

1995-12-31T23:59:59.000Z

156

Lead-Free Surface Finishes for Electronic Components  

E-Print Network (OSTI)

Lead-Free Surface Finishes for Electronic Components: Tin Whisker Growth METALS This project degraded by the switch to lead- free technology. In particular, the state of compressive stress and the localized creep response (whisker growth) of tin-based lead-free electrodeposits are being measured

Magee, Joseph W.

157

Modeling of PM Synchronous Motors for Control and Estimation Tasks  

E-Print Network (OSTI)

magnet synchronous motors in stationary frame. The model is based on linear magnetics and includes that illustrate uses of di erent models are also presented. 1 Introduction Permanent magnet synchronous motors magnet- ics for saturation e ects on motor inductances, see for example 3 ; symmetry of the stator phases

Stankoviæ, Aleksandar

158

Motor generator electric automotive vehicle  

SciTech Connect

A motor generator electric automotive vehicle is described comprising in combination, a traction drive motor coupled by a first drive shaft to a differential of an axle of the vehicle, a main battery bank electrically connected by wires to a small electric motor driving a large D.C. generator having a second drive shaft therebetween, an on-off switch in series with one of the wires to the small motor, a speed control unit attached to an accelerator pedal of the vehicle being coupled with a double pole-double throw reverse switch to the traction drive motor, a charger regulator electrically connected to the generator, a bank of solar cells coupled to the charge regulator, an electric extension cord from the charge regulator having a plug on its end for selective connection to an exterior electric power source, a plurality of pulleys on the second drive shaft, a belt unit driven by the pulley, one the belt unit being connected to a present alternator of the vehicle which is coupled to a present battery and present regulator of the vehicle, and other of the units being connected to power brakes and equipment including power steering and an air conditioner.

Weldin, W.

1986-07-29T23:59:59.000Z

159

Program to develop improved downhole drilling motors. Semiannual report  

DOE Green Energy (OSTI)

The following are described: the history of turbodrill development, positive displacement motor development, the theory of turbodrills, the theory of positive displacement motors, basic motor components, forces on thrust bearings, thrust bearing design, radial bearing design, rotary seal design, sealed lubrication system, lubricants, and project status. Included in appendices are materials on high-temperature lubricants and a progress report on the design of downhole motor seal, bearing, and lubrication test systems. (MHR)

Maurer, W.C.

1976-11-01T23:59:59.000Z

160

Practical Guide to Vegetable Oil ProcessingChapter 8 Finished Product Storage and Handling  

Science Conference Proceedings (OSTI)

Practical Guide to Vegetable Oil Processing Chapter 8 Finished Product Storage and Handling Processing eChapters Processing Press Downloadable pdf of Chapter 8 Finished Product Storage and Handling from the book ...

Note: This page contains sample records for the topic "includes finished motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Quantum motor and future  

E-Print Network (OSTI)

In a popular language, the possibilities of the Casimir expulsion effect are presented, which can be the basis of quantum motors. Such motors can be in the form of a special multilayer thin film with periodic and complex nanosized structures. Quantum motors of the type of the Casimir platforms can be the base of transportation, energy and many other systems in the future.

Evgeny G. Fateev

2013-01-20T23:59:59.000Z

162

Quantum motor and future  

E-Print Network (OSTI)

In a popular language, the possibilities of the Casimir expulsion effect are presented, which can be the basis of quantum motors. Such motors can be in the form of a special multilayer thin film with periodic and complex nanosized structures. Quantum motors of the type of the Casimir platforms can be the base of transportation, energy and many other systems in the future.

Fateev, Evgeny G

2013-01-01T23:59:59.000Z

163

Trapped field internal dipole superconducting motor generator  

DOE Patents (OSTI)

A motor generator including a high temperature superconductor rotor and an internally disposed coil assembly. The motor generator superconductor rotor is constructed of a plurality of superconductor elements magnetized to produce a dipole field. The coil assembly can be either a conventional conductor or a high temperature superconductor. The superconductor rotor elements include a magnetization direction and c-axis for the crystals of the elements and which is oriented along the magnetization direction.

Hull, John R. (Downers Grove, IL)

2001-01-01T23:59:59.000Z

164

Authorization basis supporting documentation for plutonium finishing plant  

Science Conference Proceedings (OSTI)

The identification and definition of the authorization basis for the Plutonium Finishing Plant (PFP) facility and operations are essential for compliance to DOE Order 5480.21, Unreviewed Safety Questions. The authorization basis, as defined in the Order, consists of those aspects of the facility design basis, i.e., the structures, systems and components (SSCS) and the operational requirements that are considered to be important to the safety of operations and are relied upon by DOE to authorize operation of the facility. These facility design features and their function in various accident scenarios are described in WHC-SD-CP-SAR-021, Plutonium Finishing Plant Final Safety Analysis Report (FSAR), Chapter 9, `Accident Analysis.` Figure 1 depicts the relationship of the Authorization Basis to its components and other information contained in safety documentation supporting the Authorization Basis. The PFP SSCs that are important to safety, collectively referred to as the `Safety Envelope` are discussed in various chapters of the FSAR and in WHC-SD-CP-OSR-010, Plutonium Finishing Plant Operational Safety Requirements. Other documents such as Criticality Safety Evaluation Reports (CSERS) address and support some portions of the Authorization Basis and Safety Envelope.

King, J.P., Fluor Daniel Hanford

1997-03-05T23:59:59.000Z

165

Electrical motor/generator drive apparatus and method - Energy ...  

The present disclosure includes electrical motor/generator drive systems and methods that significantly reduce inverter direct-current (DC) bus ripple currents and ...

166

Direct drive field actuator motors - Energy Innovation Portal  

A positive-drive field actuator motor including a stator carrying at least one field actuator which changes in dimension responsive to application of an energy field ...

167

ELECTRICAL MOTOR/GENERATOR DRIVE APPARATUS AND METHOD - Energy ...  

The present disclosure includes electrical motor/generator drive systems and methods that significantly reduce inverter direct-current (DC) bus ripple ...

168

Development of Ulta-Efficient Electric Motors  

SciTech Connect

Electric motors utilize a large amount of electrical energy in utility and industrial applications. Electric motors constructed with high temperature superconducting (HTS) materials have the potential to dramatically reduce electric motor size and losses. HTS motors are best suited for large motor applications at ratings above 1000 horsepower (hp), where the energy savings from the efficiency improvement can overcome the additional power required to keep the superconductors on the rotor cooled. Large HTS based motors are expected to be half the volume and have half the losses of conventional induction motors of the same rating. For a 5000 hp industrial motor, this energy savings can result in $50,000 in operating cost savings over the course of a single year of operation. Since large horsepower motors utilize (or convert) about 30% of the electrical power generated in the United States and about 70% of large motors are candidates for replacement by HTS motors, the annual energy savings potential through the utilization of HTS motors can be up to $1 Billion in the United States alone. Research in the application of HTS materials to electric motors has lead to a number of HTS motor prototypes yet no industrial HTS motor product has yet been introduced. These motor demonstrations have been synchronous motors with HTS field windings, on the rotor. Figure 1-1 shows a solid model rendering of this type of motor. The rotor winding is made with HTS coils that are held at cryogenic temperature by introducing cooling fluid from the cryocooler to the rotor through a transfer coupling. The stator winding is made of copper wire. The HTS winding is thermally isolated from the warm armature and motor shafts by a vacuum insulation space and through the use of composite torque tubes. The stator in Figure 1-1 is an air core stator in that the stator teeth and a small part of the yoke is made up of nonmagnetic material so the magnetic fields distribute themselves as if in air. Between the HTS field winding and the physical air gap is a series of concentric cylinders that act as vacuum insulation space walls as well as conducting paths for induced currents to flow in order to shield the HTS winding and the rotor cold space from time dependent fields. These time dependent fields may be caused by rotor hunting, during a change in motor load, or by non-fundamental component voltages and currents applied by the inverter. These motors are variable speed controlled by the inverter. Common large motor utility and industrial applications are pump and fan drives that are best suited by a variable speed motor. Inverter control of the HTS motor eliminates the need to design the rotor for line starting, which would dump a large amount of heat into the rotor that would then heavily tax the cryogenic cooling system. The field winding is fed by a brushless exciter that provides DC current to the HTS rotor winding. The stator winding is air or water cooled. Technical and commercial hurdles to industrial HTS motor product introduction and customer acceptance include (1) the high cost of HTS wire and the cryogenic cooling system components, (2) customer concerns about reliability of HTS motors, and (3) the ability to attain the loss reduction potential of large HTS motors. Reliance Electric has demonstrated a number of HTS based electric motors up to a 1000 hp, variable speed synchronous motor with an HTS field winding in the year 2000. In 2001 this motor was tested to 1600 hp with a sinusoidal (constant frequency) supply. Figure 1-2 shows the HTS motor on the dynamometer test stand in the Reliance Electric test lab. The extensive test program of the 1000 hp motor successfully demonstrated the technical feasibility of large HTS motors and the basic technologies involved, however the test results did indicate the need for design refinements. In addition, test results served to identify other more fundamental critical technology issues, and revealed the need to continue research efforts in order to improve future HTS motor first cost, reliability, and performa

Shoykhet, B. (Baldor Comp.); Schiferl, R. (Baldor Comp.); Duckworth, R.; Rey, C.M.; Schwenterly, S.W.; Gouge, M.J.

2008-05-01T23:59:59.000Z

169

Traffic of cytoskeletal motors with disordered attachment rates  

E-Print Network (OSTI)

Motivated by experimental results on the interplay between molecular motors and tau proteins, we extend lattice-based models of intracellular transport to include a second species of particle which locally influences the motor-filament attachment rate. We consider various exactly solvable limits of a stochastic multi-particle model before focusing on the low-motor-density regime. Here, an approximate treatment based on the random walk behaviour of single motors gives good quantitative agreement with simulation results for the tau-dependence of the motor current. Finally, we discuss the possible physiological implications of our results.

H. Grzeschik; R. J. Harris; L. Santen

2008-06-24T23:59:59.000Z

170

Hybrid vehicle motor alignment  

DOE Patents (OSTI)

A rotor of an electric motor for a motor vehicle is aligned to an axis of rotation for a crankshaft of an internal combustion engine having an internal combustion engine and an electric motor. A locator is provided on the crankshaft, a piloting tool is located radially by the first locator to the crankshaft. A stator of the electric motor is aligned to a second locator provided on the piloting tool. The stator is secured to the engine block. The rotor is aligned to the crankshaft and secured thereto.

Levin, Michael Benjamin (Ann Arbor, MI)

2001-07-03T23:59:59.000Z

171

MotorMaster+  

NLE Websites -- All DOE Office Websites (Extended Search)

industrial facilities, MotorMaster+ 4.0 contains expanded capabilities for inventory management, maintenance logging, lifecycle costing, savings tracking and trending,...

172

Reduced vibration motor winding arrangement  

DOE Patents (OSTI)

An individual phase winding arrangement having a sixty electrical degree phase belt width for use with a three phase motor armature includes a delta connected phase winding portion and a wye connected phase winding portion. Both the delta and wye connected phase winding portions have a thirty electrical degree phase belt width. The delta and wye connected phase winding portions are each formed from a preselected number of individual coils each formed, in turn, from an unequal number of electrical conductor turns in the approximate ratio of {radical}3. The individual coils of the delta and wye connected phase winding portions may either be connected in series or parallel. This arrangement provides an armature winding for a three phase motor which retains the benefits of the widely known and utilized thirty degree phase belt concept, including improved mmf waveform and fundamental distribution factor, with consequent reduced vibrations and improved efficiency. 4 figs.

Slavik, C.J.; Rhudy, R.G.; Bushman, R.E.

1997-11-11T23:59:59.000Z

173

Electric Motor Tiered Maintenance Program  

Science Conference Proceedings (OSTI)

Electric motor predictive and preventive maintenance guidance has been developed to provide information to help maximize motor reliability and to minimize the need for major motor repairs. However, if all recommendations presented in most guides are followed and applied to all motors, the cost of motor maintenance would be unwieldy and consume more than its share of maintenance budgets.

2002-08-27T23:59:59.000Z

174

Neural correlates underlying motor map plasticity and skilled motor behavior  

E-Print Network (OSTI)

of neurons within the motor cortex. Physiol Rev, 1975. 55(and S.P. Wise, The motor cortex of the rat: cytoarchitecturedelayed changes of rat motor cortical output representation

Ramanathan, Dhakshin

2007-01-01T23:59:59.000Z

175

Hermetically sealed superconducting magnet motor  

DOE Patents (OSTI)

A hermetically sealed superconducting magnet motor includes a rotor separated from a stator by either a radial gap, an axial gap, or a combined axial and radial gap. Dual conically shaped stators are used in one embodiment to levitate a disc-shaped rotor made of superconducting material within a conduit for moving cryogenic fluid. As the rotor is caused to rotate when the field stator is energized, the fluid is pumped through the conduit. 6 figs.

DeVault, R.C.; McConnell, B.W.; Phillips, B.A.

1996-07-02T23:59:59.000Z

176

Hermetically sealed superconducting magnet motor  

DOE Patents (OSTI)

A hermetically sealed superconducting magnet motor includes a rotor separated from a stator by either a radial gap, an axial gap, or a combined axial and radial gap. Dual conically shaped stators are used in one embodiment to levitate a disc-shaped rotor made of superconducting material within a conduit for moving cryogenic fluid. As the rotor is caused to rotate when the field stator is energized, the fluid is pumped through the conduit.

DeVault, Robert C. (Knoxville, TN); McConnell, Benjamin W. (Knoxville, TN); Phillips, Benjamin A. (Benton Harbor, MI)

1996-01-01T23:59:59.000Z

177

Developing a Motor Management Policy at BASF  

E-Print Network (OSTI)

In early 1998 Thomas R. Theising, BASF Corporate Engineering initiated the formation of a motor management team. The goal of the team was to develop a Motor Management Guideline to better manage the purchase and repair of motors used throughout the company. BASF draws a 240MW electrical power load. Accepting that 70% (industry standards range from 63 to 75% for BASF's businesses) of this load was consumed by rotating equipment and assuming an average cost of$401MWh at 8400 hours of annual operation BASF spends over $56M annually to operate electric motors. A guideline to better manage the purchase and repair of these motors could reduce this operating cost by 3 to 5%, which translates to $1.7M to $2.8M annually. An estimated total cost to BASF for implementation is $200K. The development of a Motor Management Guideline required the cooperative effort of a team of individuals. This team consisted of representatives from several BASF manufacturing locations, Corporate Engineering, Corporate Purchasing and Energy Management. Also, BASF included representatives from Duke Power and from Advanced Energy (AE). Advanced Energy had previously provided motor testing services to the BASF facility in Enka, NC.

Zickefoose, B.; Theising, T. R.

2001-05-01T23:59:59.000Z

178

Advanced Manufacturing Office: Motor Systems  

NLE Websites -- All DOE Office Websites (Extended Search)

Motor Systems to Motor Systems to someone by E-mail Share Advanced Manufacturing Office: Motor Systems on Facebook Tweet about Advanced Manufacturing Office: Motor Systems on Twitter Bookmark Advanced Manufacturing Office: Motor Systems on Google Bookmark Advanced Manufacturing Office: Motor Systems on Delicious Rank Advanced Manufacturing Office: Motor Systems on Digg Find More places to share Advanced Manufacturing Office: Motor Systems on AddThis.com... Quick Links Energy Resource Center Technical Publications by Energy System Energy-Efficient Technologies Incentives & Resources by Zip Code Better Plants Superior Energy Performance Contacts Motor Systems Photo of Man Checking Motor Performance Motor-driven equipment accounts for 54% of manufacturing electricity use. Dramatic energy and cost savings can be achieved in motor systems by

179

Energy Efficient Motors  

E-Print Network (OSTI)

Efficiency is only one aspect of motor performance. This paper discusses how efficiency is influenced by such factors as horsepower rating, poles, actual load, and starting requirements. It discusses some of the variables affecting efficiency, and how to interpret efficiency data. A perspective is given from which to evaluate available energy efficient motor offerings for a given application.

Hoffmeyer, W.

1982-01-01T23:59:59.000Z

180

Stepping motor controller  

SciTech Connect

A stepping motor is microprocessingly controlled by digital circuitry which monitors the output of a shaft encoder adjustably secured to the stepping motor and generates a subsequent stepping pulse only after the preceding step has occurred and a fixed delay has expired. The fixed delay is variable on a real-time basis to provide for smooth and controlled deceleration.

Bourret, Steven C. (Los Alamos, NM); Swansen, James E. (Los Alamos, NM)

1984-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "includes finished motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Stepping motor controller  

DOE Patents (OSTI)

A stepping motor is microprocessor controlled by digital circuitry which monitors the output of a shaft encoder adjustably secured to the stepping motor and generates a subsequent stepping pulse only after the preceding step has occurred and a fixed delay has expired. The fixed delay is variable on a real-time basis to provide for smooth and controlled deceleration.

Bourret, S.C.; Swansen, J.E.

1982-07-02T23:59:59.000Z

182

System and method to determine electric motor efficiency using an equivalent circuit  

DOE Patents (OSTI)

A system and method for determining electric motor efficiency includes a monitoring system having a processor programmed to determine efficiency of an electric motor under load while the electric motor is online. The determination of motor efficiency is independent of a rotor speed measurement. Further, the efficiency is based on a determination of stator winding resistance, an input voltage, and an input current. The determination of the stator winding resistance occurs while the electric motor under load is online.

Lu, Bin (Kenosha, WI); Habetler, Thomas G. (Snellville, GA)

2011-06-07T23:59:59.000Z

183

Genetics of motor neuron disease  

Science Conference Proceedings (OSTI)

The number of genes associated with motor neuron degen- eration has increased ... Motor neurons are affected in a large number of neurologic diseases

184

Motor Vehicle Parts Compliance Requirements  

Science Conference Proceedings (OSTI)

... The OVSC compliance testing program is a strong incentive for manufacturers of motor vehicles and items of motor vehicle equipment to ...

2012-09-24T23:59:59.000Z

185

Aurica Motors | Open Energy Information  

Open Energy Info (EERE)

Product California-based Aurica Motors is planning to develop and manufacture an electric vehicle at a former Toyota plant in the state. References Aurica Motors1...

186

Efficient, High-Torque Electric Vehicle Motor: Advanced Electric Vehicle Motors with Low or No Rare Earth Content  

SciTech Connect

REACT Project: QM Power will develop a new type of electric motor with the potential to efficiently power future generations of EVs without the use of rare-earth-based magnets. Many of todays EV motors use rare earth magnets to efficiently provide torque to the wheels. QM Powers motors would contain magnets that use no rare earth minerals, are light and compact, and can deliver more power with greater efficiency and at reduced cost. Key innovations in this project include a new motor design with iron-based magnetic materials, a new motor control technique, and advanced manufacturing techniques that substantially reduce the cost of the motor. The ultimate goal of this project is to create a cost-effective EV motor that offers the rough peak equivalent of 270 horsepower.

None

2012-01-01T23:59:59.000Z

187

GENII dose calculations for offsite maximum individual and populations from Plutonium Finishing Plant  

Science Conference Proceedings (OSTI)

Document describes the potential dose consequences to the offsite maximum individual and population for ground and stack level releases at the offsite receptors from the Plutonium Finishing Plant.

Nguyen, L.V.

1995-09-29T23:59:59.000Z

188

Losses and Costs Associated with Coal vs. Natural Gas Firing at Hanes Dye and Finishing.  

E-Print Network (OSTI)

??Due to decreasing production and rising coal prices, the engineering and management staff at Hanes Dye and Finishing in Winston Salem, NC have been investigating (more)

Gibides, Justin Tyler

2009-01-01T23:59:59.000Z

189

DTRA Algorithm Prize (Seventh Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting 2012)  

Science Conference Proceedings (OSTI)

Christian Whitchurch on the "DTRA Algorithm Prize" at the 2012 Sequencing, Finishing, Analysis in the Future Meeting held June 5-7, 2012 in Santa Fe, New Mexico.

Whitechurch, Christian [Defense Threat Reduction Agency

2012-06-01T23:59:59.000Z

190

Flame retardant finishing for cotton using a hydroxy-functional organophosphorus oligomer.  

E-Print Network (OSTI)

??New durable flame retardant finishing systems based on a hydroxy-functional organophosphorus oligomer (HFPO) and a bonding agent have been developed for cotton. In this research, (more)

Wu, Weidong

2004-01-01T23:59:59.000Z

191

Modular PM Motor Drives for Automotive Traction Applications  

DOE Green Energy (OSTI)

This paper presents modular permanent magnet (PM) motor drives for automotive traction applications. A partially modularized drive system consisting of a single PM motor and multiple inverters is described. The motor has multiple three-phase stator winding sets and each winding set is driven with a separate three-phase inverter module. A truly modularized inverter and motor configuration based on an axial-gap PM motor is then introduced, in which identical PM motor modules are mounted on a common shaft and each motor module is powered by a separate inverter module. The advantages of the modular approach for both inverter and motor include: (1) power rating scalability--one design meets different power requirements by simply stacking an adequate number of modules, thus avoiding redesigning and reducing the development cost, (2) increased fault tolerance, and (3) easy repairing. A prototype was constructed by using two inverters and an axial-gap PM motor with two sets of three-phase stat or windings, and it is used to assist the diesel engine in a hybrid electric vehicle converted from a Chevrolet Suburban. The effect of different pulse-width-modulation strategies for both motoring and regenerative modes on current control is analyzed. Torque and regenerative control algorithms are implemented with a digital signal processor. Analytical and initial testing results are included in the paper.

Su, G.J.

2001-10-29T23:59:59.000Z

192

Summer 2003 Motor Gasoline Outlook  

U.S. Energy Information Administration (EIA)

Summer 2003 Motor Gasoline Outlook ... State gasoline taxes ... that occurred between spring 1999 and fall 2001, ...

193

MOTOR POOL RESERVATIONS Reservation Number:_______________  

E-Print Network (OSTI)

MOTOR POOL RESERVATIONS Reservation Number:_______________ Evanston campus: Chicago campus: 2020: 312/503-9243 E-mail: motor-pool@northwestern.edu E-mail: motor-pool@northwestern.edu Hours: 8:00 a reservations require the "Organization Authorization for University Vehicles" form to be faxed to Motor Pool

Shull, Kenneth R.

194

Linear Motor Powered Transportation  

E-Print Network (OSTI)

This special issue on linear-motor powered transportation covers both supporting technologies and innovative transport systems in various parts of the World, as this technology moves from the lab to commercial operations. ...

Thornton, Richard D.

195

Ford Motor Company  

E-Print Network (OSTI)

All statements, findings, and conclusions in this report are those of the authors and do not necessarily reflect those of the Global Interdependence Center, Ford Motor Company, or the Center for Automotive Research. TABLE OF CONTENTS Acknowledgements......................................................................................................................... iv

Ellen Hughes-cromwick; Joshua Cregger

2013-01-01T23:59:59.000Z

196

Retail Motor Gasoline Prices*  

Gasoline and Diesel Fuel Update (EIA)

motor gasoline is projected to be about 1.38 per gallon. As was the case with heating oil, last year's peak average gasoline price, at 1.633 per gallon in June, was the...

197

Markov Process of Muscle Motors  

E-Print Network (OSTI)

We study a Markov random process describing a muscle molecular motor behavior. Every motor is either bound up with a thin filament or unbound. In the bound state the motor creates a force proportional to its displacement from the neutral position. In both states the motor spend an exponential time depending on the state. The thin filament moves at its velocity proportional to average of all displacements of all motors. We assume that the time which a motor stays at the bound state does not depend on its displacement. Then one can find an exact solution of a non-linear equation appearing in the limit of infinite number of the motors.

Yu. Kondratiev; E. Pechersky; S. Pirogov

2007-06-20T23:59:59.000Z

198

Plutonium Finishing Plant. Interim plutonium stabilization engineering study  

SciTech Connect

This report provides the results of an engineering study that evaluated the available technologies for stabilizing the plutonium stored at the Plutonium Finishing Plant located at the hanford Site in southeastern Washington. Further processing of the plutonium may be required to prepare the plutonium for interim (<50 years) storage. Specifically this document provides the current plutonium inventory and characterization, the initial screening process, and the process descriptions and flowsheets of the technologies that passed the initial screening. The conclusions and recommendations also are provided. The information contained in this report will be used to assist in the preparation of the environmental impact statement and to help decision makers determine which is the preferred technology to process the plutonium for interim storage.

Sevigny, G.J.; Gallucci, R.H.; Garrett, S.M.K.; Geeting, J.G.H.; Goheen, R.S.; Molton, P.M.; Templeton, K.J.; Villegas, A.J. [Pacific Northwest Lab., Richland, WA (United States); Nass, R. [Nuclear Fuel Services, Inc. (United States)

1995-08-01T23:59:59.000Z

199

Trends in motor gasolines: 1942-1981  

Science Conference Proceedings (OSTI)

Trends in motor gasolines for the years of 1942 through 1981 have been evaluated based upon data contained in surveys that have been prepared and published by the Bartlesville Energy Technology Center (BETC). These surveys have been published twice annually since 1935 describing the properties of motor gasolines from throughout the country. The surveys have been conducted in cooperation with the American Petroleum Institute (API) since 1948. Various companies from throughout the country obtain samples from retail outlets, analyze the samples by the American Society for Testing and Materials (ASTM) procedures, and report data to the Bartlesville center for compilation, tabulation, calculation, analysis and publication. A typical motor gasoline report covers 2400 samples from service stations throughout the country representing some 48 companies that manufacture and supply gasoline. The reports include trend charts, octane plots, and tables of test results from about a dozen different tests. From these data in 77 semiannual surveys, a summary report has thus been assembled that shows trends in motor gasolines throughout the entire era of winter 1942 to 1943 to the present. Trends of physical properties including octane numbers, antiknock ratings, distillation temperatures, Reid vapor pressure, sulfur and lead content are tabulated, plotted and discussed in the current report. Also included are trend effects of technological advances and the interactions of engine design, societal and political events and prices upon motor gasoline evolution during the 40 year period.

Shelton, E M; Whisman, M L; Woodward, P W

1982-06-01T23:59:59.000Z

200

Advanced motor driven clamped borehole seismic receiver  

DOE Patents (OSTI)

A borehole seismic tool is described including a borehole clamp which only moves perpendicular to the borehole. The clamp is driven by an electric motor, via a right angle drive. When used as a seismic receiver, the tool has a three part housing, two of which are hermetically sealed. Accelerometers or geophones are mounted in one hermetically sealed part, the electric motor in the other hermetically sealed part, and the clamp and right angle drive in the third part. Preferably the tool includes cable connectors at both ends. Optionally a shear plate can be added to the clamp to extend the range of the tool.

Engler, B.P.; Sleefe, G.E.; Striker, R.P.

1993-02-23T23:59:59.000Z

Note: This page contains sample records for the topic "includes finished motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Power-Factor and Torque Calculation with Consideration of Cross Saturation of the Interior Permanent Magnet Synchronous Motor with  

E-Print Network (OSTI)

Permanent Magnet Synchronous Motor with Brushless Field Excitation Seong Taek Lee1,2 , Timothy A. Burress1 permanent magnet synchronous motor (IPMSM). The conventional two-axis IPMSM model is modified to include motor of a hybrid electric vehicle. I. INTRODUCTION The interior permanent magnet synchronous motor

Tolbert, Leon M.

202

Steam Turbine Efficiency and Corrosion: Effects of Surface Finish, Deposits, and Moisture  

Science Conference Proceedings (OSTI)

The causes of steam turbine losses have been recognized for over 50 years. In practice, deposits and surface finish account for major losses during turbine blade path audits. This report presents new experimental information on the effects of surface finish, moisture removal, and deposits.

2001-10-31T23:59:59.000Z

203

Dynein Motor Domain Shows Ring-Shaped Motor, Buttress  

NLE Websites -- All DOE Office Websites (Extended Search)

Dynein Motor Domain Shows Ring-Shaped Motor, Buttress Print Dynein Motor Domain Shows Ring-Shaped Motor, Buttress Print Movement is fundamental to life. It takes place even at the cellular level where cargo is continually being transported by motor proteins. These tiny machines convert the energy gained from hydrolysing ATP into a series of small conformational changes that allow them to literally "walk" along microscopic tracks. Motor proteins (in the kinesin and myosin families) have been extensively studied by x-ray crystallography, but until recently there was little molecular structural information for dyneins, another type of motor protein. A group from the University of California, San Francisco, working at ALS Beamline 8.3.1 has reported the 6-Å-resolution structure of the motor domain of dynein in yeast. It reveals details of the ring-shaped motor as well as a new, unanticipated feature called the buttress that may play an important role in dynein's mechanical cycle.

204

Dynein Motor Domain Shows Ring-Shaped Motor, Buttress  

NLE Websites -- All DOE Office Websites (Extended Search)

Dynein Motor Domain Shows Ring-Shaped Motor, Buttress Print Dynein Motor Domain Shows Ring-Shaped Motor, Buttress Print Movement is fundamental to life. It takes place even at the cellular level where cargo is continually being transported by motor proteins. These tiny machines convert the energy gained from hydrolysing ATP into a series of small conformational changes that allow them to literally "walk" along microscopic tracks. Motor proteins (in the kinesin and myosin families) have been extensively studied by x-ray crystallography, but until recently there was little molecular structural information for dyneins, another type of motor protein. A group from the University of California, San Francisco, working at ALS Beamline 8.3.1 has reported the 6-Å-resolution structure of the motor domain of dynein in yeast. It reveals details of the ring-shaped motor as well as a new, unanticipated feature called the buttress that may play an important role in dynein's mechanical cycle.

205

Dynein Motor Domain Shows Ring-Shaped Motor, Buttress  

NLE Websites -- All DOE Office Websites (Extended Search)

Dynein Motor Domain Shows Ring-Shaped Motor, Buttress Print Dynein Motor Domain Shows Ring-Shaped Motor, Buttress Print Movement is fundamental to life. It takes place even at the cellular level where cargo is continually being transported by motor proteins. These tiny machines convert the energy gained from hydrolysing ATP into a series of small conformational changes that allow them to literally "walk" along microscopic tracks. Motor proteins (in the kinesin and myosin families) have been extensively studied by x-ray crystallography, but until recently there was little molecular structural information for dyneins, another type of motor protein. A group from the University of California, San Francisco, working at ALS Beamline 8.3.1 has reported the 6-Å-resolution structure of the motor domain of dynein in yeast. It reveals details of the ring-shaped motor as well as a new, unanticipated feature called the buttress that may play an important role in dynein's mechanical cycle.

206

Dynein Motor Domain Shows Ring-Shaped Motor, Buttress  

NLE Websites -- All DOE Office Websites (Extended Search)

Dynein Motor Domain Shows Ring-Shaped Motor, Buttress Print Dynein Motor Domain Shows Ring-Shaped Motor, Buttress Print Movement is fundamental to life. It takes place even at the cellular level where cargo is continually being transported by motor proteins. These tiny machines convert the energy gained from hydrolysing ATP into a series of small conformational changes that allow them to literally "walk" along microscopic tracks. Motor proteins (in the kinesin and myosin families) have been extensively studied by x-ray crystallography, but until recently there was little molecular structural information for dyneins, another type of motor protein. A group from the University of California, San Francisco, working at ALS Beamline 8.3.1 has reported the 6-Å-resolution structure of the motor domain of dynein in yeast. It reveals details of the ring-shaped motor as well as a new, unanticipated feature called the buttress that may play an important role in dynein's mechanical cycle.

207

Instrinsic oscillations of treadmilling microtubules in a motor bath  

E-Print Network (OSTI)

We analyse the dynamics of overlapping antiparallel treadmilling microtubules in the presence of crosslinking processive motor proteins that counterbalance an external force. We show that coupling the force-dependent velocity of motors and the kinetics of motor exchange with a bath in the presence of treadmilling leads generically to oscillatory behavior. In addition we show that coupling the polymerization kinetics to the external force through the kinetics of the crosslinking motors can stabilize the oscillatory instability into finite-amplitude nonlinear oscillations and may lead to other scenarios, including bistability.

Sudipto Muhuri; Ignacio Pagonabarraga; Jaume Casademunt

2011-09-16T23:59:59.000Z

208

Instrinsic oscillations of treadmilling microtubules in a motor bath  

E-Print Network (OSTI)

We analyse the dynamics of overlapping antiparallel treadmilling microtubules in the presence of crosslinking processive motor proteins that counterbalance an external force. We show that coupling the force-dependent velocity of motors and the kinetics of motor exchange with a bath in the presence of treadmilling leads generically to oscillatory behavior. In addition we show that coupling the polymerization kinetics to the external force through the kinetics of the crosslinking motors can stabilize the oscillatory instability into finite-amplitude nonlinear oscillations and may lead to other scenarios, including bistability.

Muhuri, Sudipto; Casademunt, Jaume

2011-01-01T23:59:59.000Z

209

The motor theory of social cognition: a critique  

E-Print Network (OSTI)

Recent advances in the cognitive neuroscience of action have considerably enlarged our understanding of human motor cognition. In particular, the activity of the mirror system, first discovered in the brain of nonhuman primates, provides an observer with the understanding of a perceived action by means of the motor simulation of the agents observed movements. This discovery has raised the prospects of a motor theory of social cognition. In humans, social cognition includes the ability to mindread, and many motor theorists of social cognition try to bridge the gap between motor cognition and mindreading by endorsing a simulation account of mindreading. Here, we question the motor theory of social cognition and give reasons for our skepticism.

Pierre Jacob; Marc Jeannerod

2005-01-01T23:59:59.000Z

210

Ontario Hydro Motor Efficiency Study  

E-Print Network (OSTI)

Electric motors consume more than one-half of the electrical energy produced by Ontario Hydro. In the residential sector, the major motor load is for refrigerators and freezers while packaged equipment dominate the motor load in the commercial market. However, this paper concentrates on the industrial market since 76% of this market's load is motors. The poly phase integral horsepower motor is the "workhorse" of industry. The efficiency of the standard induction motor can be improved. The new "high efficiency" motor is described and the operating cost is compared to the standard motor. Payback for high efficiency motors is found to be about one year for continuous duty applications. Specific instructions are presented for use in industry.

Dautovich, D. R.

1980-01-01T23:59:59.000Z

211

Drilling motor deviation tool  

Science Conference Proceedings (OSTI)

An extension for a down hole drilling motor is described, which adapts the motor for selective configuration for straight hole drilling or directional drilling, selectively. It consists of: an elongated generally tubular body, adapted at a first end to rigidly attach to the lower end of a down hole drilling motor housing, the body having an opening extending along the general centerline of the body; fluid channel means situated in the opening to conduct drilling fluid from the motor fluid output means to a downwardly continuing drill string element; output shaft means situated in the body and extending from a second end of the body, the output shaft adapted at the extended extreme for attachment to a downwardly continuing drill string element; selector valve means situated in the body, operatively associated with drilling fluid channels in the body, responsive to drilling fluid flow to produce a first output signal in response to fluid flow manipulations having a first characteristic and to produce a second output signal in response to fluid flow manipulations having a second characteristic; and driveshaft connector means in the opening, operatively associated with the output shaft of the motor and the output shaft means to connect the two for sympathetic rotation.

Falgout, T.E.; Schoeffler, W.N.

1989-03-14T23:59:59.000Z

212

Sensory-Motor Integration and Control  

E-Print Network (OSTI)

spinal interneurons during motor pattern generation inStep, Swim, and Scratch Motor Patterns in the Turtle. JStep, Swim, and Scratch Motor Patterns in the Turtle. J

Welch, Dan Bruce

2011-01-01T23:59:59.000Z

213

High-megawatt Electric Drive Motors  

Science Conference Proceedings (OSTI)

... Page 2. ABB BU Machines April 10, 2009 | Slide 2 High-megawatt Electric Drive Motors ... motor concept ... A selection of compressor motors >30MW. ...

2012-10-21T23:59:59.000Z

214

The MotorMaster+ Software Tool  

NLE Websites -- All DOE Office Websites (Extended Search)

motors.html MotorMaster+ also provides technical data that can assist with the optimization of drive systems, motor purchasing, and energy accounting, as well as energy...

215

Brushless Motor Controller Report Spring 2010  

E-Print Network (OSTI)

Brushless Motor Controller Report Spring 2010 May 15, 2010 Brian Clementi MAE of 2010 322 Bogert ...................................................................................................... 5 A. Motor Description...................................................................................................... 5 B. The Motor Controller Board

Ruina, Andy L.

216

Commercial Motor Vehicle Brake-Related Research  

E-Print Network (OSTI)

Commercial Motor Vehicle Brake-Related Research Commercial Motor Vehicle Roadside Technology Corridor Safety Technology Showcase October 14, 2010 Commercial Motor Vehicle Roadside Technology Corridor

217

Advanced Manufacturing Office: MotorMaster+ International  

NLE Websites -- All DOE Office Websites (Extended Search)

special or definite purpose motors. To quickly determine the annual energy and dollar savings of a NEMA Premium efficiency or EFF1 motor over a lower efficiency motor...

218

Universal adaptive torque control for PM motors for field-weakening region operation  

Science Conference Proceedings (OSTI)

The invention includes a motor controller and method for controlling a permanent magnet motor. In accordance with one aspect of the present technique, a permanent magnet motor is controlled by, among other things, receiving a torque command, determining a normalized torque command by normalizing the torque command to a characteristic current of the motor, determining a normalized maximum available voltage, determining an inductance ratio of the motor, and determining a direct-axis current based upon the normalized torque command, the normalized maximum available voltage, and the inductance ratio of the motor.

Royak, Semyon (Beachwood, OH); Harbaugh, Mark M. (Richfield, OH); Breitzmann, Robert J. (South Russel, OH); Nondahl, Thomas A. (Wauwatosa, WI); Schmidt, Peter B. (Franklin, WI); Liu, Jingbo (Milwaukee, WI)

2011-03-29T23:59:59.000Z

219

Bent shaft motor  

DOE Patents (OSTI)

A nonelectromagnetic motor comprising a base, a bent shaft which is rotable relative to the base wherein the bent shaft comprises a straight portion aligned with a main axis and an offset portion that is offset with respect to the main axis; and a drive means for driving the offset portion of the bent shaft along a generally circular path in a plane perpendicular to the main axis to rotate the bent shaft. The bent shaft and drive means for driving the bent shaft can be selected from piezoelectric, magnetostrictive, rheological and shape memory alloys. The drive means of the nonelectromagnetic motor can additionally comprise a shell which shell surrounds and houses the bent shaft and precesses or gyrates which in turn causes the bent drive shaft to rotate. The nonelectromagnetic motor does not rely on friction for the application of torque upon a rotor.

Benavides, Gilbert L. (Albuquerque, NM)

1998-01-01T23:59:59.000Z

220

Dynein Motor Domain Shows Ring-Shaped Motor, Buttress  

NLE Websites -- All DOE Office Websites (Extended Search)

Dynein Motor Domain Shows Ring-Shaped Motor, Buttress Print Movement is fundamental to life. It takes place even at the cellular level where cargo is continually being transported...

Note: This page contains sample records for the topic "includes finished motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Motor current signature analysis method for diagnosing motor operated devices  

DOE Patents (OSTI)

A motor current noise signature analysis method and apparatus for remotely monitoring the operating characteristics of an electric motor-operated device such as a motor-operated valve. Frequency domain signal analysis techniques are applied to a conditioned motor current signal to distinctly identify various operating parameters of the motor driven device from the motor current signature. The signature may be recorded and compared with subsequent signatures to detect operating abnormalities and degradation of the device. This diagnostic method does not require special equipment to be installed on the motor-operated device, and the current sensing may be performed at remote control locations, e.g., where the motor-operated devices are used in accessible or hostile environments.

Haynes, Howard D. (Kingston, TN); Eissenberg, David M. (Oak Ridge, TN)

1990-01-01T23:59:59.000Z

222

Design and prototyping methods for brushless motors and motor control  

E-Print Network (OSTI)

In this report, simple, low-cost design and prototyping methods for custom brushless permanent magnet synchronous motors are explored. Three case-study motors are used to develop, illustrate and validate the methods. Two ...

Colton, Shane W. (Shane William)

2010-01-01T23:59:59.000Z

223

3M's Motor Challenge Showcase Demonstration Project  

E-Print Network (OSTI)

In January 1994, 3M began the task of optimizing the electric motor systems at 3M Center, a 26 building, 7 million square foot corporate campus. A cross-functional, cross-company team was established which included four 3M employees representing two different departments within 3M, an engineer specializing in demand side management programs from Northern States Power Company, and a sales engineer from General Electric Supply Company. The team was later joined by an engineering specialist from Landis & Staefa, Inc., a building automation controls supplier. The team began the task of identifying the projects that could save energy and provide a reasonable return on 3M's investment on a building by building approach. As surveys were completed, proposals were prepared and presented to management requesting funding. The team continued the process of identifying projects in remaining buildings and took on the responsibility of designing, contracting and implementing projects as funding was approved for those already studied. Follow-up measurements to ascertain that the savings predicted was actually achieved are done before project close-out. This project was submitted and accepted as a Motor Challenge Showcase Demonstration Project. The Motor Challenge is a U.S. Department of Energy initiative to promote the efficient use of energy in electric motor systems. Showcase Demonstration Projects are used to exemplify the benefits that motor system optimization can provide. This Showcase Project is different from most as it emphasizes the process that was developed to carry out a project of this magnitude rather than any single specific technologies or applications. The team has completed the project at 3M Center. Measured savings are $823,000 per year. This paper will discuss the Motor Challenge Showcase Demonstration project that was completed at 3M Center, the motor systems survey methodology the team developed, analysis tools and techniques and the results that have been attained.

Schultz, S. C.

1998-04-01T23:59:59.000Z

224

3M's Motor Challenge Showcase Demonstration Project  

E-Print Network (OSTI)

In January 1994, 3M began the task of optimizing the electric motor systems at 3M Center, a 26 building, 7 million square foot corporate campus. A cross-functional, cross-company team was established which included four 3M employees representing two different departments within 3M, an engineer specializing in demand side management programs from Northern States Power Company, and a sales engineer from General Electric Supply Company. The team was later joined by an engineering specialist from Landis & Gyr, Inc., a building automation controls supplier. The team began the task of identifying the projects that could save energy and provide a reasonable return on 3M's investment on a building by building approach. As surveys were completed, proposals were prepared and presented to management requesting funding. The team continued the process of identifying projects in remaining buildings and took on the responsibility of designing, contracting and implementing projects as funding was approved for those already studied. Follow-up measurements to ascertain that the savings predicted was actually achieved are done before project close-out. This project was submitted and has been accepted as a Motor Challenge Showcase Demonstration Project. The Motor Challenge is a U. S. Department of Energy initiative to promote the efficient use of energy in electric motor systems. Showcase Demonstration Projects are used to exemplify the benefits that motor system optimization can provide. This Showcase Project is different from most as it emphasizes the process that was developed to carry out a project of this magnitude rather than any single specific technologies or applications. The team has nearly completed the studies at 3M Center and is well into the implementation phase with six buildings being complete. Savings identified to date are approximately $810,000 per year. This paper will discuss the Motor Challenge Showcase Demonstration project currently underway at 3M Center, the motor systems survey methodology the team developed, analysis tools and techniques and the results that have been attained.

Schultz, S. C.

1996-04-01T23:59:59.000Z

225

Method for assessing motor insulation on operating motors  

DOE Patents (OSTI)

A method for monitoring the condition of electrical-motor-driven devices. The method is achieved by monitoring electrical variables associated with the functioning of an operating motor, applying these electrical variables to a three phase equivalent circuit and determining non-symmetrical faults in the operating motor based upon symmetrical components analysis techniques.

Kueck, John D. (Oak Ridge, TN); Otaduy, Pedro J. (Oak Ridge, TN)

1997-01-01T23:59:59.000Z

226

Method for assessing motor insulation on operating motors  

DOE Patents (OSTI)

A method for monitoring the condition of electrical-motor-driven devices is disclosed. The method is achieved by monitoring electrical variables associated with the functioning of an operating motor, applying these electrical variables to a three phase equivalent circuit and determining non-symmetrical faults in the operating motor based upon symmetrical components analysis techniques. 15 figs.

Kueck, J.D.; Otaduy, P.J.

1997-03-18T23:59:59.000Z

227

Trouble-Shooting Guide for Low-Voltage ASD/Motor Systems  

Science Conference Proceedings (OSTI)

ASD/low-voltage motor systems are used extensively by manufacturing and many other industries for a variety of reasons, including flexibility in manufacturing, energy conservation, and improved process control. There can be, however, reliability problems with ASD/motor systems. This report discusses ASD/motor system-related issues and provides guidance in identifying and solving the root causes of problems.

1998-12-31T23:59:59.000Z

228

US military expenditures to protect the use of Persian Gulf oil for motor vehicles  

E-Print Network (OSTI)

US military expenditures to protect the use of Persian Gulf oil for motor vehicles Mark A. Delucchi 2008 Keywords: Oil importing cost Motor fuel social cost Energy security cost a b s t r a c t Analyses of the full social cost of motor vehicle use in the US often estimate an ``oil import premium'' that includes

Murphy, James J.

229

Brandl Motor | Open Energy Information  

Open Energy Info (EERE)

Motor Jump to: navigation, search Name Brandl Motor Address Calvinstr 24 Place Berlin Zip 10557 Sector Marine and Hydrokinetic Phone number +49 30 39 48 06 38 Website http:http:...

230

AGNI Motors | Open Energy Information  

Open Energy Info (EERE)

Place India Zip 370 230 Sector Vehicles Product UK-based manufacturer of DC Motors and Battery Management Systems for Electric Vehicles References AGNI Motors1 LinkedIn...

231

Commercial Motor Vehicle Brake Assessment Tools  

E-Print Network (OSTI)

Commercial Motor Vehicle Brake Assessment Tools Commercial Motor Vehicle Roadside Technology Corridor Safety Technology Showcase October 14, 2010 Commercial Motor Vehicle Roadside Technology Corridor #12;Overview · Commercial Motor Vehicle (CMV) Air Brake System · North American Standard Level-1

232

Energy Savings of Variable Speed Motors  

E-Print Network (OSTI)

This paper investigates the energy savings available by utilizing variable speed motors on pump and fan applications. Conventional control of flow or pressure in process plants is normally accomplished by throttling the various streams with control valves. Depending on the system and the actual operating conditions, this throttling may consume a considerable amount of energy. The hydraulics of different systems are investigated to generalize high energy saving applications. Typical pump characteristics at varying speeds are investigated since most performance curves are only available at a constant speed. The various types of variable speed electric motors are discussed. However, the primary variable speed system recommended is a variable frequency speed system which utilizes standard induction motors. Specific cases of centrifugal pump applications and cooling tower fan service are presented. Turndown frequencies, stream factors, and electric rates are included in the evaluation. The energy savings of a variable speed system becomes significant when flow rates vary widely and the electrical rates are high.

Fishel, F. D.

1979-01-01T23:59:59.000Z

233

Multiple stage miniature stepping motor  

DOE Patents (OSTI)

A stepping motor comprising a plurality of stages which may be selectively activated to effect stepping movement of the motor, and which are mounted along a common rotor shaft to achieve considerable reduction in motor size and minimum diameter, whereby sequential activation of the stages results in successive rotor steps with direction being determined by the particular activating sequence followed.

Niven, William A. (Livermore, CA); Shikany, S. David (Danville, CA); Shira, Michael L. (Fremont, CA)

1981-01-01T23:59:59.000Z

234

Guide for Determining Motor Repair versus Motor Replacement  

Science Conference Proceedings (OSTI)

The Motor Replacement/Refurbishment Guide (MRRG) was written to aid with the determination on whether to repair an existing motor or to purchase a replacement motor. This guideline provides the basic tools necessary to make a determination based upon, but not limited to, the extent of the repair scope and the cost of the repair. This guideline presents a process to be utilized by the station or corporate motor specialist to assess the motor repair scope both initial and revised. The data gathering proces...

2005-12-23T23:59:59.000Z

235

Electrostatic generator/motor configurations  

DOE Patents (OSTI)

Electrostatic generators/motors designs are provided that include a stator fixedly connected to a first central support centered about a central axis. The stator elements are attached to the first central support. Similarly, a second stator is connected to a central support centered about the central axis, and the second stator has stator elements attached to the second central support. A rotor is located between the first stator and the second stator and includes an outer support, where the rotor is rotatably centered about the central axis, the rotor having elements in contact with the outer support, each rotor element having an extending rotor portion that extends radially from the outer support toward the axis of rotation.

Post, Richard Freeman

2012-09-11T23:59:59.000Z

236

Motor technology for mining applications advances  

SciTech Connect

AC motors are steadily replacing DC motors in mining and mineral processing equipment, requiring less maintenance. The permanent magnet rotor, or the synchronous motor, has enabled Blador to introduce a line of cooling tower motors. Synchronous motors are soon likely to take over from the induction motor. 1 photo.

Fiscor, S.

2009-08-15T23:59:59.000Z

237

ams2000.com Stepper Motor System Basics  

E-Print Network (OSTI)

. STEPPING MOTORS TYPES OF STEPPING MOTORS VARIABLE RELUCTANCE PERMANENT MAGNET HYBRID MOTOR WINDINGS motor with the magnetic field electronically switched to rotate the armature magnet around. A Stepping MOTORS There are basically three types of stepping motors; variable reluctance, permanent magnet

Bechtold, Jill

238

System design description for the HMT Rotation Motor Heater System  

SciTech Connect

This document is the design description for the Rotation Motor Heater System on waste tank 241-SY-101. The description includes the certified vendor (CV) file number, operators instructions, and heater sizing calculations.

Vargo, G.F. Jr.

1995-05-18T23:59:59.000Z

239

Tool Path Planning Generation For Finish Machining of Freeform Surfaces in the Cybercut Process Planning Pipeline  

E-Print Network (OSTI)

CYBERCUT PROCESS PLANNING PIPELINE Paul K. Wright, David A.describes part of a "Pipeline of De- sign and Manufacturingversus surface finish. 2.5D PIPELINE AND 3D SURFACES Figure

Wright, Paul K; Dornfeld, David; Sundararajan, V.; Misra, Debananda

2007-01-01T23:59:59.000Z

240

Signature Peptide-Enabled Metagenomics (Seventh Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting 2012)  

Science Conference Proceedings (OSTI)

Ben McMahon of Los Alamos National Laboratory (LANL) presents "Signature Peptide-Enabled Metagenomics" at the 7th Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting held in June, 2012 in Santa Fe, NM.

McMahon, Ben [LANL

2012-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "includes finished motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Metagenomics for Etiologic Agent Discovery (Seventh Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting 2012)  

Science Conference Proceedings (OSTI)

Matthew Ross on "Metagenomics for etiological agent discovery" at the 2012 Sequencing, Finishing, Analysis in the Future Meeting held June 5-7, 2012 in Santa Fe, New Mexico.

Ross, Matthew [Baylor College of Medicine

2012-06-01T23:59:59.000Z

242

Pilon: Automated Assembly Improvement Software (Seventh Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting 2012)  

Science Conference Proceedings (OSTI)

Bruce Walker on "Pilon: Automated Assembly Improvement Software" at the 2012 Sequencing, Finishing, Analysis in the Future Meeting held June 5-7, 2012 in Santa Fe, New Mexico.

Walker, Bruce (Broad Institute)

2012-06-01T23:59:59.000Z

243

Evaluating High Efficiency Motor Retrofit  

E-Print Network (OSTI)

In the petrochemical and refining Industries, and most manufacturing plants, the reliable operation of AC motors always has been crucial to the continuous operation of the process. Now, the cost of operating these motors has also become a significant factor. Engineers Involved In motor specification can help lower plant operating costs and reduce electrical energy consumption dramatically by a relatively simple technique: retrofit of existing, standard-efficiency motors with new, high efficiency models. This article demonstrates strong reasons for motor retrofit, and explains step-by step how process and manufacturing engineering personnel can fully evaluate a retrofit decision.

Evans, T. A.

1984-01-01T23:59:59.000Z

244

A Plutonium Finishing Plant Model for the Cercla Removal Action and Decommissioning Construction Final Report  

Science Conference Proceedings (OSTI)

The joint policy between the U.S. Environmental Protection Agency (EPA) and the U.S. Department of Energy (DOE) for decommissioning buildings at DOE facilities documents an agreement between the agencies to perform decommissioning activities including demolition under the Comprehensive Environmental Response Compensation and Liability Act (CERCLA). The use of removal actions for decommissioning integrates EPA oversight authority, DOE lead agency responsibility, and state authority for decommissioning activities. Once removal actions have been performed under CERCLA, a construction completion report is required to document the completion of the required action. Additionally, a decommissioning report is required under DOE guidance. No direct guidance was found for documenting completion of decommissioning activities and preparing a final report that satisfies the CERCLA requirements and the DOE requirements for decommissioning. Additional guidance was needed for the documentation of construction completion under CERCLA for D and D projects undertaken under the joint policy that addresses the requirements of both agencies. A model for the construction completion report was developed to document construction completion for CERCLA D and D activities performed under the joint EPA/DOE policy at the Plutonium Finishing Plant (PFP). The model documentation report developed at PFP integrates the DOE requirements for establishing decommissioning end-points, documenting end-point completion and preparing a final decommissioning report with the CERCLA requirements to document completion of the action identified in the Action Memorandum (AM). The model includes the required information on health and safety, data management, cost and schedule and end-points completion. (authors)

Hopkins, A. [Fluor Hanford, Inc, Richland, WA (United States)

2008-07-01T23:59:59.000Z

245

Technical Basis for Work Place Air Monitoring for the Plutonium Finishing Plan (PFP)  

SciTech Connect

This document establishes the basis for the Plutonium Finishing Plant's (PFP) work place air monitoring program in accordance with the following requirements: Title 10, Code of Federal Regulations (CFR), Part 835 ''Occupational Radiation Protection''; Hanford Site Radiological Control Manual (HSRCM-1); HNF-PRO-33 1, Work Place Air Monitoring; WHC-SD-CP-SAR-021, Plutonium Finishing Plant Final Safety Analysis Report; and Applicable recognized national standards invoked by DOE Orders and Policies.

JONES, R.A.

1999-10-06T23:59:59.000Z

246

The Allocation of the Social Costs of Motor-Vehicle Use to Six Classes of Motor Vehicles  

E-Print Network (OSTI)

higher the amount of foreign oil embodied, and consequentlyof domestic and foreign crude oil used to make motor fuels10-13b). Mass of foreign crude oil (including unfinished

Delucchi, Mark A.

1996-01-01T23:59:59.000Z

247

Retail Motor Gasoline Prices*  

Gasoline and Diesel Fuel Update (EIA)

6 6 Notes: Gasoline pump prices have backed down from the high prices experienced last summer and fall. The retail price for regular motor gasoline fell 11 cents per gallon from September to December. However, with crude oil prices rebounding somewhat from their December lows combined with lower than normal stock levels, we project that prices at the pump will rise modestly as the 2001 driving season begins this spring. For the summer of 2001, we expect only a little difference from the average price of $1.50 per gallon seen during the previous driving season, as motor gasoline stocks going into the driving season are projected to be slightly less than they were last year. The situation of relatively low inventories for gasoline could set the stage for some regional imbalances in supply that could once again

248

System Cost Analysis for an Interior Permanent Magnet Motor  

DOE Green Energy (OSTI)

The objective of this program is to provide an assessment of the cost structure for an interior permanent magnet ('IPM') motor which is designed to meet the 2010 FreedomCAR specification. The program is to evaluate the range of viable permanent magnet materials for an IPM motor, including sintered and bonded grades of rare earth magnets. The study considers the benefits of key processing steps, alternative magnet shapes and their assembly methods into the rotor (including magnetization), and any mechanical stress or temperature limits. The motor's costs are estimated for an annual production quantity of 200,000 units, and are broken out into such major components as magnetic raw materials, processing and manufacturing. But this is essentially a feasibility study of the motor's electromagnetic design, and is not intended to include mechanical or thermal studies as would be done to work up a selected design for production.

Peter Campbell

2008-08-01T23:59:59.000Z

249

Figure 10. U.S. Average Retail Regular Motor Gasoline and ...  

U.S. Energy Information Administration (EIA)

U.S. Average Retail Regular Motor Gasoline and On-Highway Diesel Fuel Prices, January 2013 to Present ... Including Taxes) Title: Weekly Petroleum ...

250

Plutonium Finishing Plan (PFP) Treatment and Storage Unit Waste Analysis Plan  

Science Conference Proceedings (OSTI)

The purpose of this waste analysis plan (WAP) is to document waste analysis activities associated with the Plutonium Finishing Plant Treatment and Storage Unit (PFP Treatment and Storage Unit) to comply with Washington Administrative Code (WAC) 173-303-300(1), (2), (4)(a) and (5). The PFP Treatment and Storage Unit is an interim status container management unit for plutonium bearing mixed waste radiologically managed as transuranic (TRU) waste. TRU mixed (TRUM) waste managed at the PFP Treatment and Storage Unit is destined for the Waste Isolation Pilot Plant (WIPP) and therefore is not subject to land disposal restrictions [WAC 173-303-140 and 40 CFR 268]. The PFP Treatment and Storage Unit is located in the 200 West Area of the Hanford Facility, Richland Washington (Figure 1). Because dangerous waste does not include source, special nuclear, and by-product material components of mixed waste, radionuclides are not within the scope of this documentation. The information on radionuclides is provided only for general knowledge.

PRIGNANO, A.L.

2000-07-01T23:59:59.000Z

251

Method and apparatus for monitoring motor operated valve motor ...  

A method and apparatus are provided for monitoring a motor operated valve during the brief period when the valve seats and the torque switch trips to deenergize the ...

252

Plant Engineering: Critical Motor Refurbishment and Procurement Checklist - Key Project Phases and Considerations  

Science Conference Proceedings (OSTI)

This report provides guidance for projects involving procurement and refurbishment of motors. These projects are complex and include many steps that are critical for success. Key steps and activities (including oversight) that are required to ensure a successful outcome when procuring or refurbishing motors in accordance with rigid specifications are included in this guidance.

2013-06-19T23:59:59.000Z

253

Advanced Manufacturing Office: MotorMaster+  

NLE Websites -- All DOE Office Websites (Extended Search)

MotorMaster+ to MotorMaster+ to someone by E-mail Share Advanced Manufacturing Office: MotorMaster+ on Facebook Tweet about Advanced Manufacturing Office: MotorMaster+ on Twitter Bookmark Advanced Manufacturing Office: MotorMaster+ on Google Bookmark Advanced Manufacturing Office: MotorMaster+ on Delicious Rank Advanced Manufacturing Office: MotorMaster+ on Digg Find More places to share Advanced Manufacturing Office: MotorMaster+ on AddThis.com... MotorMaster+ This photo shows the inner workings of an industrial electric motor with gears. In the lower left hand corner are the words "MotorMaster+" and underneath are the words "Motor-Driven Systems." Download MotorMaster+ now! Version: 4.01.01 Release Date: September 21, 2010 Release Notes Metric Unit Measurements: No

254

NVLAP Efficiency of Electric Motors  

Science Conference Proceedings (OSTI)

... program was originally developed at the request of the National Electrical Manufacturers Association (NEMA) to assist the electric motor industry in ...

2013-05-14T23:59:59.000Z

255

Imports of Total Motor Gasoline  

U.S. Energy Information Administration (EIA)

Reformulated and conventional gasoline production excludes adjustments for fuel ethanol and motor gasoline blending components. Historical data prior to June 4, ...

256

Electric Motors and Critical Materials  

NLE Websites -- All DOE Office Websites (Extended Search)

Research Suggestions (Have an idea of how to get there) * Integration of motor, power converter, and speed reducer * Soft magnetic core material with high saturation...

257

Primary Metals - Compressor Motors Failing  

Science Conference Proceedings (OSTI)

This power quality (PQ) case study presents the investigation of four failures of compressor motors for a two stage chiller at a primary metals manufacturing facility.

2003-12-31T23:59:59.000Z

258

Shipping and Storage of Electric Motors  

Science Conference Proceedings (OSTI)

Electric motor predictive and preventive maintenance programs have been written and describe the best methodology for increasing motor reliability. However, many utilities have invested substantial resources into the procurement of spare motors. These motors are stored both onsite and off site (at vendor facilities). In addition, motors are being refurbished/reconditioned and must be shipped and possibly stored upon return.

2004-12-20T23:59:59.000Z

259

Pacing plant motors for energy savings  

SciTech Connect

Electronic adjustable-speed drives (ASDs) allow power plant auxiliary motors to work only as hard as they need to. In some cases, ASDs can reduce energy requirements by 30-50%, while minimizing wear and tear. Electronic ASDs' advanced hardware and software make them more compact than their mechanical counterparts, so retrofits are a relatively simple undertaking. Electric Power Research Institute studies include development and testing on ASDs retrofits and seeking new applications. 2 references, 6 figures.

Lihach, N.; Ferraro, R.

1984-03-01T23:59:59.000Z

260

Effects of a range of machined and ground surface finishes on the simulated reactor helium corrosion of several candidate structural materials. [Inconel MA 754  

SciTech Connect

This report discusses the corrosion behavior of several candidate reactor structural alloys in a simulated advanced high-temperature gas-cooled reactor (HTGR) environment over a range of lathe-machined and centerless-ground surface finishes. The helium environment contained 50 Pa H/sub 2//5 Pa CO/5 Pa CH/sub 4//<0.05 Pa H/sub 2/O (500 ..mu..atm H/sub 2//50 ..mu..atm CO/50 ..mu..atm CH/sub 4//<0.5 ..mu..atm H/sub 2/O) at 900/sup 0/C for a total exposure of 3000 h. The test alloys included two vacuum-cast superalloys (IN 100 and IN 713LC); a centrifugally cast austenitic alloy (HK 40); three wrought high-temperature alloys (Alloy 800H, Hastelloy X, and Inconel 617); and a nickel-base oxide-dispersion-strengthened alloy (Inconel MA 754). Surface finish variations did not affect the simulated advanced-HTGR corrosion behavior of these materials. Under these conditions, the availability of reactant gaseous impurities controls the kinetics of the observed gas-metal interactions. Variations in the near-surface activities and mobilities of reactive solute elements, such as chromium, which might be expected to be affected by changes in surface finish, do not seem to greatly influence corrosion in this simulated advanced HTGR environment. 18 figures, 4 tables.

Thompson, L.D.

1981-02-01T23:59:59.000Z

Note: This page contains sample records for the topic "includes finished motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Simple cost model for EV traction motors  

DOE Green Energy (OSTI)

A simple cost model has been developed that allows the calculation of the OEM cost of electric traction motors of three different types, normalized as a function of power in order to accommodate different power and size. The model includes enough information on the various elements integrated in the motors to allow analysis of individual components and to factor-in the effects of changes in commodities prices. A scalable cost model for each of the main components of an electric vehicle (EV) is a useful tool that can have direct application in computer simulation or in parametric studies. For the cost model to have wide usefulness, it needs to be valid for a range of values of some parameter that determines the magnitude or size of the component. For instance, in the case of batteries, size may be determined by energy capacity, usually expressed in kilowatt-hours (kWh), while in the case of traction motors, size is better determined by rated power, usually expressed in kilowatts (kW). The simplest case is when the cost of the component in question is a direct function of its size; then cost is simply the product of its specific cost ($/unit size) and the number of units (size) in the vehicle in question. Batteries usually fall in this category (cost = energy capacity x $/kWh). But cost is not always linear with size or magnitude; motors (and controllers), for instance, become relatively less expensive as power rating increases. Traction motors, one of the main components for EV powertrains are examined in this paper, and a simplified cost model is developed for the three most popular design variations.

Cuenca, R.M.

1995-02-01T23:59:59.000Z

262

Using MotorMaster to Track Motor Inventory and Analyze Purchasing Decisions  

E-Print Network (OSTI)

MotorMaster 4.0 can be a useful software package for electric motor management decisions in industrial facilities. To be successful, the MotorMaster database must be populated with detailed motor nameplate information. Georgia Tech worked with a large, motor intensive chemical manufacturing plant to collect motor nameplate information on motors 60 hp or larger and populate the motor database. Approximately 130 motors were identified and surveyed. The completed motor database is used to track maintenance actions and to analyze motor replacement options. The approach used to secure and enter motor nameplate data along with examples of purchasing analyses completed will be presented. The success of the MotorMaster software with large motors has convinced the firm to expand its use to smaller horsepower motors.

Brown, M.; Meffort, W.

2007-01-01T23:59:59.000Z

263

Patterning of the Ciona intestinalis Motor Ganglion  

E-Print Network (OSTI)

Pitx2 as markers for fast motor neurons and partition cells.for the specification of motor neuron identity. Cell Gans,Tsuda, M. (2010). Simple motor system of the ascidian larva:

Stolfi, Alberto Sunao

2011-01-01T23:59:59.000Z

264

Industrial motor repair in the United States  

Science Conference Proceedings (OSTI)

This report characterizes the motor repair industry in the United States; summarizes current motor repair and testing practice; and identifies barriers to energy motor repair practice and recommends strategies for overcoming those barriers.

Schueler, V.; Leistner, P.; Douglass, J.

1994-09-01T23:59:59.000Z

265

COMMERICAL MOTOR VEHICLE OPERATOR EMPLOYMENT APPLICATION SUPPLEMENT  

E-Print Network (OSTI)

COMMERICAL MOTOR VEHICLE OPERATOR EMPLOYMENT APPLICATION SUPPLEMENT _________________________________________________________ Applicants for positions involving the operation of a commercial motor vehicle must comply with Title 49 CFR: _______________ Please list the following information for each unexpired commercial motor vehicle operator license

Roy, Subrata

266

Commercial Motor Vehicle Roadside Technology Corridor (CMVRTC)  

E-Print Network (OSTI)

Commercial Motor Vehicle Roadside Technology Corridor (CMVRTC) Oak Ridge National Laboratory Safety Security Vehicle Technologies Research Brief T he Commercial Motor Vehicle Roadside Technology in Tennessee to demonstrate, test, evaluation, and showcase innovative commercial motor vehicle (CMV) safety

267

Improvements in Sand Mold/Core Technology: Effects on Casting Finish  

SciTech Connect

In this study, the development and impact of density gradients on metal castings were investigated using sand molds/cores from both industry and from in-house production. In spite of the size of the castings market, almost no quantitative information about density variation within the molds/cores themselves is available. In particular, a predictive understanding of how structure and binder content/chemistry/mixing contribute to the final surface finish of these products does not exist. In this program we attempted to bridge this gap by working directly with domestic companies in examining the issues of surface finish and thermal reclamation costs resulting from the use of sand molds/cores. We show that these can be substantially reduced by the development of an in-depth understanding of density variations that correlate to surface finish. Our experimental tools and our experience with them made us uniquely qualified to achieve technical progress.

Prof. John J. Lannutti; Prof. Carroll E. Mobley

2005-08-30T23:59:59.000Z

268

As Auto X Reaches the Finish Line, a New Race Begins | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

As Auto X Reaches the Finish Line, a New Race Begins As Auto X Reaches the Finish Line, a New Race Begins As Auto X Reaches the Finish Line, a New Race Begins September 17, 2010 - 4:20pm Addthis John Schueler John Schueler Former New Media Specialist, Office of Public Affairs When the Automotive X Prize competition began back in March of 2008, the organizers laid out an ambitious goal: inspire a new generation of viable, safe and super fuel-efficient vehicles capable of achieving 100 miles per gallon or the energy equivalent (MPGe). The response they received was staggering -- 136 vehicle design proposals from teams across the globe, all eager to innovate and set a new standard for energy efficiency. In the two years since the competition was announced, the field thinned through various stages of competition, evaluation and testing. Not content

269

Permanent magnet assisted synchronous reluctance motor, design and performance improvement  

E-Print Network (OSTI)

Recently, permanent magnet assisted (PMa)-synchronous reluctance motors (SynRM) have been considered as a possible alternative motor drive for high performance applications. In order to have an efficient motor drive, performing of three steps in design of the overall drive is not avoidable. These steps are design optimization of the motor, identification of the motor parameter and implementation of an advanced control system to ensure optimum operation. Therefore, this dissertation first deals with the design optimization of the Permanent Magnet Assisted Synchronous Reluctance Motor (PMa-SynRM). Various key points in the rotor design of a low cost PMa-SynRM are introduced and their effects are studied. Finite element approach has been utilized to show the effects of these parameters on the developed average electromagnetic torque and the total d-q inductances. As it can be inferred from the name of the motor, there are some permanent magnets mounted in the rotor core. One of the features considered in the design of this motor is the magnetization of the permanent magnets mounted in the rotor core using the stator windings to reduce the manufacturing cost. At the next step, identification of the motor parameters is discussed. Variation of motor parameters due to temperature and airgap flux has been reported in the literatures. Use of off-line models for estimating the motor parameters is known as a computationally intensive method, especially when the models include the effect of cross saturation. Therefore in practical applications, on-line parameter estimation is favored to achieve a high performance control system. In this dissertation, a simple practical method for parameter estimation of the PMa-SynRM is introduced. Last part of the dissertation presents one advanced control strategy which utilized the introduced parameter estimator. A practical Maximum Torque Per Ampere (MTPA) control scheme along with a simple parameter estimator for PMa-SynRM is introduced. This method is capable of maintaining the MTPA condition and stays robust against the variations of motor parameters. Effectiveness of the motor design procedure and the control strategy is validated by presenting simulation and experimental results of a 1.5 kW prototype PMa-SynRM, designed and manufactured through the introduced design method.

Niazi, Peyman

2005-12-01T23:59:59.000Z

270

Program to develop improved downhole drilling motors. Semi-annual report  

DOE Green Energy (OSTI)

Research progress is reported in two main sections: downhole drilling motor design and design of downhole motor seal, bearing, and test lubrication systems. Information on downhole drilling motor design is presented under the following subsection headings: Turbodrill development; positive displacement motor development; theory of Turbodrills; theory of positive displacement motors; basic motor components; forces on thrust bearings; thrust bearing design; radial bearing design; rotary seal design; sealed lubrication system; lubricants; and project status. The appendix contains information on high temperature lubricants. Information on the design of downhole motor seal, bearing, and test lubrication systems is presented under the following subsection headings: seal, bearing, and lubrication test design criteria; basic test conditions; independent and dependent variable parameters; alternative concepts for seal test apparatus; design of the seal test system; and bearing test system description. A schedule for remaining tasks is included. (JGB)

Maurer, W.C.

1976-11-01T23:59:59.000Z

271

Coking is a refinery process that produces 19% of finished ...  

U.S. Energy Information Administration (EIA)

Petroleum & Other Liquids. Crude oil, gasoline, heating oil, diesel, propane, and other liquids including biofuels and natural gas liquids. Natural Gas

272

Trexa Motor Corporation TMC | Open Energy Information  

Open Energy Info (EERE)

Trexa Motor Corporation TMC Jump to: navigation, search Name Trexa Motor Corporation (TMC) Place Los Angeles, California Sector Vehicles Product Los Angeles - based subsidiary of...

273

PC Based wireless stepper motor control.  

E-Print Network (OSTI)

??This project is about making an embedded system in order to control different functionalities of a stepper motor. The main functions of this stepper motor (more)

Jamal, Omar; Khan, Shahnawaz

2013-01-01T23:59:59.000Z

274

CQST/CNEX Efficiency of Electric Motors  

Science Conference Proceedings (OSTI)

CQST/CNEX Efficiency of Electric Motors. NVLAP Lab Code: 200609-0. ... Send E-Mail to NVLAP at: NVLAP@nist.gov. Efficiency of Electric Motors. ...

2013-08-16T23:59:59.000Z

275

Mission Motors Company | Open Energy Information  

Open Energy Info (EERE)

Motors Company Place San Francisco, California Zip 94103 Product San Francisco-based electric Motorcycle manufacturer. References Mission Motors Company1 LinkedIn...

276

CQST/CNEX Efficiency of Electric Motors  

Science Conference Proceedings (OSTI)

... of Electric Motors. Accreditation Valid From: January 1, 2013 Through: December 31, 2013. [24/M01] IEEE 112, Method B Electric Motor Efficiency ...

2013-08-16T23:59:59.000Z

277

Determining Electric Motor Load and Efficiency  

NLE Websites -- All DOE Office Websites (Extended Search)

nance logging, inventory control, energy and dollar savings tracking, and life cycle cost analysis. MotorMaster+ is available at no cost to Motor Challenge Partners. 10 Electrical...

278

Advanced Manufacturing Office: MotorMaster+ International  

NLE Websites -- All DOE Office Websites (Extended Search)

on Twitter Bookmark Advanced Manufacturing Office: MotorMaster+ International on Google Bookmark Advanced Manufacturing Office: MotorMaster+ International on Delicious Rank...

279

Turn Motors Off When Not in Use  

SciTech Connect

This is one in a series of tip sheets to help manufacturers optimize their industrial motor and motor-driven systems.

Not Available

2008-07-01T23:59:59.000Z

280

Magnetically Coupled Adjustable Speed Motor Drives  

Science Conference Proceedings (OSTI)

This is one in a series of tip sheets to help manufacturers optimize their industrial motor and motor-driven systems.

Not Available

2008-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "includes finished motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Highly Efficient Electric Motor Systems - National Renewable ...  

Electric Motor Systems ... savings. Conical hubs Matching axial field poles. Issued Patents on Motor Geometry. 7 NREL Energy Forum November 2009 www.novatorque.com.

282

Piezoelectric wave motor  

DOE Patents (OSTI)

A piezoelectric motor having a stator in which piezoelectric elements are contained in slots formed in the stator transverse to the desired wave motion. When an electric field is imposed on the elements, deformation of the elements imposes a force perpendicular to the sides of the slot, deforming the stator. Appropriate frequency and phase shifting of the electric field will produce a wave in the stator and motion in a rotor. In a preferred aspect, the piezoelectric elements are configured so that deformation of the elements in direction of an imposed electric field, generally referred to as the d.sub.33 direction, is utilized to produce wave motion in the stator. In a further aspect, the elements are compressed into the slots so as to minimize tensile stresses on the elements in use.

Yerganian, Simon Scott (Lee' s Summit, MO)

2001-07-17T23:59:59.000Z

283

Piezoelectric wave motor  

DOE Patents (OSTI)

A piezoelectric motor having a stator in which piezoelectric elements are contained in slots formed in the stator transverse to the desired wave motion. When an electric field is imposed on the elements, deformation of the elements imposes a force perpendicular to the sides of the slot, deforming the stator. Appropriate frequency and phase-shifting of the electric field will produce a wave in the stator and motion in a rotor. In a preferred aspect, the piezoelectric elements are configured so that deformation of the elements in the direction of an imposed electric field, generally referred to as the d.sub.33 direction, is utilized to produce wave motion in the stator. In a further aspect, the elements are compressed into the slots so as to minimize tensile stresses on the elements in use.

Yerganian, Simon Scott (Lee' s Summit, MO)

2003-02-11T23:59:59.000Z

284

Dual power, constant speed electric motor system  

DOE Patents (OSTI)

A dual capacity permanent split capacitor electric motor system is provided with a stator having main and auxiliary windings. The main stator winding includes two winding sections which are connected in parallel with each other and across a pair of line terminals while the auxiliary winding is connected in series with a capacitor to form a circuit branch which is connected between the line terminals for operation at a first output power level. Switching means are provided to reconnect the main stator winding sections in series with each other and in series with a second capacitor to form a circuit branch which is connected between the line terminals while the stator auxiliary winding is connected directly between the line terminals for operation at a second output power level. Automatic rotation reversal occurs when the motor switches from the first to the second output power level.

Kirschbaum, Herbert S. (Asheville, NC)

1984-01-01T23:59:59.000Z

285

Dual power, constant speed electric motor system  

DOE Patents (OSTI)

A dual capacity permanent split capacitor electric motor system is provided with a stator having main and auxiliary windings. The main stator winding includes two winding sections which are connected in parallel with each other and across a pair of line terminals while the auxiliary winding is connected in series with a capacitor to form a circuit branch which is connected between the line terminals for operation at a first output power level. Switching means are provided to reconnect the main stator winding sections in series with each other and in series with a second capacitor to form a circuit branch which is connected between the line terminals while the stator auxiliary winding is connected directly between the line terminals for operation at a second output power level. Automatic rotation reversal occurs when the motor switches from the first to the second output power level. 6 figs.

Kirschbaum, H.S.

1984-07-31T23:59:59.000Z

286

ALS: a disease of motor neurons and their nonneuronal neighbors  

E-Print Network (OSTI)

Amyotrophic lateral sclerosis is a late-onset progressive neurodegenerative disease affecting motor neurons. The etiology of most ALS cases remains unknown, but 2 % of instances are due to mutations in Cu/Zn superoxide dismutase (SOD1). Since sporadic and familial ALS affects the same neurons with similar pathology, it is hoped that therapies effective in mutant SOD1 models will translate to sporadic ALS. Mutant SOD1 induces non-cell-autonomous motor neuron killing by an unknown gain of toxicity. Selective vulnerability of motor neurons likely arises from a combination of several mechanisms, including protein misfolding, mitochondrial dysfunction, oxidative damage, defective axonal transport, excitotoxicity, insufficient growth factor signaling, and inflammation. Damage within motor neurons is enhanced by damage incurred by nonneuronal neighboring cells, via an inflammatory response that accelerates disease progression. These findings validate therapeutic approaches aimed at nonneuronal cells.

Sverine Boille; Christine V; E Velde; Don W. Clevel

2006-01-01T23:59:59.000Z

287

Hanford Facility Dangerous Waste Closure Plan - Plutonium Finishing Plant Treatment Unit Glovebox HA-20MB  

Science Conference Proceedings (OSTI)

This closure plan describes the planned activities and performance standards for closing the Plutonium Finishing Plant (PFP) glovebox HA-20MB that housed an interim status ''Resource Conservation and Recovery Act'' (RCRA) of 1976 treatment unit. This closure plan is certified and submitted to Ecology for incorporation into the Hanford Facility RCRA Permit (HF RCRA Permit) in accordance with Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement; TPA) Milestone M-83-30 requiring submittal of a certified closure plan for ''glovebox HA-20MB'' by July 31, 2003. Glovebox HA-20MB is located within the 231-5Z Building in the 200 West Area of the Hanford Facility. Currently glovebox HA-20MB is being used for non-RCRA analytical purposes. The schedule of closure activities under this plan supports completion of TPA Milestone M-83-44 to deactivate and prepare for dismantlement the above grade portions of the 234-5Z and ZA, 243-Z, and 291-Z and 291-Z-1 stack buildings by September 30, 2015. Under this closure plan, glovebox HA-20MB will undergo clean closure to the performance standards of Washington Administrative Code (WAC) 173-303-610 with respect to all dangerous waste contamination from glovebox HA-20MB RCRA operations. Because the intention is to clean close the PFP treatment unit, postclosure activities are not applicable to this closure plan. To clean close the unit, it will be demonstrated that dangerous waste has not been left at levels above the closure performance standard for removal and decontamination. If it is determined that clean closure is not possible or is environmentally impractical, the closure plan will be modified to address required postclosure activities. Because dangerous waste does not include source, special nuclear, and by-product material components of mixed waste, radionuclides are not within the scope of this documentation. Any information on radionuclides is provided only for general knowledge. Clearance form only sent to RHA.

PRIGNANO, A.L.

2003-06-25T23:59:59.000Z

288

Comparative Summer Thermal Performance of Finished and Unfinished Metal Roofing Products with Composition Shingles  

E-Print Network (OSTI)

This paper presents an overview of results from experimental research conducted at FSEC's Flexible Roofing Facility in the summer of 2002. The Flexible Roof Facility (FRF) is a test facility in Cocoa, Florida designed to evaluate a combination of five roofing systems against a control roof using dark shingles. The intent of the testing is to evaluate how roofing systems impact residential cooling energy use. Recent testing emphasizes evaluation of how increasingly popular metal roofing systems, both finished and unfinished, might compare with other more traditional roofing types. All of the test cells had R-19 insulation installed on the attic floor except in the double roof configuration which had R-19 of open cell foam blown onto the underside of the roof decking. The test results were used to determine relative thermal performance of various roofing systems under typical Florida summer conditions. Measured impacts included changes to ceiling heat flux and attic air temperature which influences loads from unintended attic air leakage and duct heat gain. We also develop an analysis method to estimate total cooling energy benefits of different roofing systems considering the various impacts. The results show that all the options perform better than dark composition shingles. White metal performs best with an estimated cooling energy reduction of about 15%, but the spectrally selective metal shingles (12%) and unfinished Galvalume roofs (11%) do surprisingly well. Galvanized roofing did less well than Galvalume (7% reduction) and worse performance in the second year of exposure was observed due to corrosion of the zinc surface. The sealed attic with a double roof produced an estimated cooling energy reduction of only 2% -- largely due to increases in ceiling flux.

Parker, D. S.; Sherwin, J.; Sonne, J.

2004-01-01T23:59:59.000Z

289

Submersible canned motor transfer pump  

DOE Patents (OSTI)

A transfer pump used in a waste tank for transferring high-level radioactive liquid waste from a waste tank and having a column assembly, a canned electric motor means, and an impeller assembly with an upper impeller and a lower impeller connected to a shaft of a rotor assembly. The column assembly locates a motor housing with the electric motor means adjacent to the impeller assembly which creates an hydraulic head, and which forces the liquid waste, into the motor housing to cool the electric motor means and to cool and/or lubricate the radial and thrust bearing assemblies. Hard-on-hard bearing surfaces of the bearing assemblies and a ring assembly between the upper impeller and electric motor means grind large particles in the liquid waste flow. Slots in the static bearing member of the radial bearing assemblies further grind down the solid waste particles so that only particles smaller than the clearances in the system can pass therethrough, thereby resisting damage to and the interruption of the operation of the transfer pump. The column assembly is modular so that sections can be easily assembled, disassembled and/or removed. A second embodiment employs a stator jacket which provides an alternate means for cooling the electric motor means and lubricating and/or cooling the bearing assemblies, and a third embodiment employs a variable level suction device which allows liquid waste to be drawn into the transfer pump from varying and discrete levels in the waste tank.

Guardiani, Richard F. (Ohio Township, Allegheny County, PA); Pollick, Richard D. (Sarver, PA); Nyilas, Charles P. (Monroeville, PA); Denmeade, Timothy J. (Lower Burrell, PA)

1997-01-01T23:59:59.000Z

290

IEMDC -IN-LINE ELECTRIC MOTOR DRIVEN COMPRESSOR  

SciTech Connect

Dresser-Rand completed the preliminary aerodynamic flowpath of the volute and inlet design for the compressor section. This has resulted in considerable progress being made on the development of the compressor section and ultimately towards the successful integration of the IEMDC System design. Significant effort was put forth in the design of aerodynamic components which resulted in a design that meets the limits of aerodynamically induced radial forces previously established. Substantial effort has begun on the mechanical design of the compressor pressure containing case and other internal components. These efforts show progression towards the successful integration of a centrifugal compressor and variable speed electric motor ventilated by the process gas. All efforts continue to confirm the feasibility of the IEMDC system design. During the third quarter reporting period, the focus was to further refine the motor design and to ensure that the IEMDC rotor system supported on magnetic bearing is in compliance with the critical speed and vibration requirements of the API standards 617 and 541. Consequently specification to design magnetic bearings was developed and an RFQ to three magnetic bearing suppliers was issued. Considerable work was also performed to complete preliminary reports on some of the deliverable tasks under phase 1.0. These include specification for the VFD, RFQ for the magnetic bearings, and preliminary write-up for motor instrumentation and control schematic. In order to estimate motor efficiency at various operating points, plots of calculated motor losses, and motor cooling gas flow rates were also prepared. Preliminary evaluations of motor support concepts were performed via FEA to determine modal frequencies. Presentation was made at DOE Morgantown on August 12, 2003 to provide project status update. Preparations for the IEMDC motor-compressor presentation, at the GMRC conference in Salt Lake City to be held on October 5, 2003, were also started. Detailed calculations of cooling gas flow requirements for the motor and magnetic bearings, per several new operating points designated by DR, confirmed that the required gas flow was within the compressor design guidelines. Previous thrust load calculations had confirmed that the magnetic thrust bearing design load capacity of 6,000 lb. was sufficient to handle the net thrust load produced by the motor and compressor pressure loading. Thus the design data that has been generated, for the variable speed 10 MW 12,000 rpm motor, during the last three quarters, continue to confirm the feasibility of an efficient and robust motor design.

Michael J. Crowley; Prem N. Bansal; John E. Tessaro

2004-01-01T23:59:59.000Z

291

The Integrated Safety Management System Verification Enhancement Review of the Plutonium Finishing Plant (PFP)  

SciTech Connect

The primary purpose of the verification enhancement review was for the DOE Richland Operations Office (RL) to verify contractor readiness for the independent DOE Integrated Safety Management System Verification (ISMSV) on the Plutonium Finishing Plant (PFP). Secondary objectives included: (1) to reinforce the engagement of management and to gauge management commitment and accountability; (2) to evaluate the ''value added'' benefit of direct public involvement; (3) to evaluate the ''value added'' benefit of direct worker involvement; (4) to evaluate the ''value added'' benefit of the panel-to-panel review approach; and, (5) to evaluate the utility of the review's methodology/adaptability to periodic assessments of ISM status. The review was conducted on December 6-8, 1999, and involved the conduct of two-hour interviews with five separate panels of individuals with various management and operations responsibilities related to PFP. A semi-structured interview process was employed by a team of five ''reviewers'' who directed open-ended questions to the panels which focused on: (1) evidence of management commitment, accountability, and involvement; and, (2) consideration and demonstration of stakeholder (including worker) information and involvement opportunities. The purpose of a panel-to-panel dialogue approach was to better spotlight: (1) areas of mutual reinforcement and alignment that could serve as good examples of the management commitment and accountability aspects of ISMS implementation, and, (2) areas of potential discrepancy that could provide opportunities for improvement. In summary, the Review Team found major strengths to include: (1) the use of multi-disciplinary project work teams to plan and do work; (2) the availability and broad usage of multiple tools to help with planning and integrating work; (3) senior management presence and accessibility; (4) the institutionalization of worker involvement; (5) encouragement of self-reporting and self-assessment by management; (6) the availability of multiple internal communication mechanisms; and, (7) the existence of overall facility-wide safety management goals as well as individualized project work team goals. Major opportunities for improvement identified include: (1) the enhancement of external communications relative to ISM; (2) the institutionalization of ISM-related performance agreements/incentives; (3) the strengthening of feedback loops; (4) fine-tuning the use of tools; and, (5) the formalization of good practices.

BRIGGS, C.R.

2000-02-09T23:59:59.000Z

292

Research Laboratories General Motors Corporation General Motors Technical Center  

Office of Legacy Management (LM)

MI. 1-q Research Laboratories General Motors Corporation General Motors Technical Center Warren, Michigan 48090 January 21, 1977 Occupational Health Standards Branch Office of Standards Development U. S. Nuclear Requlatory Commission Washington, D.C. 20555 Attention: Mr. Robert E. Alexander, Chief Dear Mr. Alexander: In 1974, General Motors Corporation acquired a manufacturing plant in Adrian, Michigan. On October 21, 1976, General Motors announced that work would begin immediately to prepare the plant for manufacturing operations (Appendix A). A news release, made by Mr. Irving Loop of ERDA and carried by radio station WABJ of Adrian, Michigan on May 11, 1976, stated that natural uranium was handled in the plant after World War II and that

293

Predicted concentrations in new relocatable classrooms of volatile organic compounds emitted from standard and alternate interior finish materials  

SciTech Connect

Relocatable classrooms (RCs) are widely employed by California school districts to satisfy rapidly expanding space requirements due to population growth and class size reduction policies. There is public concern regarding indoor environmental quality (IEQ) in schools, particularly in RCs, but very little data to support or dispel these concerns. Several studies are investigating various aspects of IEQ in California schools. This laboratory-based study focused on evaluating the emissions of toxic and/or odorous volatile organic compounds (VOCs), including formaldehyde and acetaldehyde, from materials used to finish the interiors of new RCs. Furthermore, the study implemented a procedure for VOC source reduction by testing and selecting lower-emitting materials as substitutes for standard materials. In total, 17 standard and alternate floor coverings, wall panels and ceiling panels were quantitatively tested for emissions of VOCs using smallscale environmental chambers. Working with the largest northern California manufacturer of conventional RCs and two school districts, specifications were developed for four new RCs to be produced in early summer 2001. Two of these will be predominantly finished with standard materials. Alternate carpet systems, an alternate wall panel covering and an alternate ceiling panel were selected for the two other RCs based on the results of the laboratory study and considerations of cost and anticipated performance and maintenance. Particular emphasis was placed on reducing the concentrations of VOCs on California agency lists of toxic compounds. Indoor concentrations of toxic and odorous VOCs were estimated for the four classrooms by mass balance using the measured VOC emission factors, exposed surface areas of the materials in the RCs, and three ventilation rate scenarios. Results indicate that reductions in the concentrations of formaldehyde, acetaldehyde phenol, di(ethylene glycol) butyl ether, vinyl acetate, 1,2,4-trimethylbenzene and 1-methyl-2-pyrrolidinone should be achieved as the result of the source reduction procedure.

Hodgson, Alfred T.; Fisk, William J.; Shendell, Derek G.; Apte, Michael G.

2001-07-01T23:59:59.000Z

294

Doubly Salient Permanent Magnet Motor Development Review  

Science Conference Proceedings (OSTI)

The research of doubly salient permanent magnet motor (DSPM), arises as the emergence of a novel type mechatronic control of AC drive system. Currently, on the international realm, the studies regarding on this kind of motor mainly focus on calculation ... Keywords: Doubly Salient, Permanent Magnet Motor, AC Variable Speed, Magnetic Materials, Switched Reluctance Motor

Lina Yi, Meng Zhao

2013-09-01T23:59:59.000Z

295

Ultra-Efficient and Power Dense Electric Motors for U. S. Industry  

SciTech Connect

The primary purpose of this project was to combine the ease-of-installation and ease-of-use attributes of industrial induction motors with the low-loss and small size and weight advantages of PM motors to create an ultra-efficient, high power density industrial motor that can be started across-the-line or operated from a standard, Volts/Hertz drive without the need for a rotor position feedback device. PM motor products that are currently available are largely variable speed motors that require a special adjustable speed drive with rotor position feedback. The reduced size and weight helps to offset the magnet cost in order make these motors commercially viable. The scope of this project covers horsepower ratings from 20 ? 500. Prototypes were built and tested at ratings ranging from 30 to 250 HP. Since fans, pumps and compressors make up a large portion of industrial motor applications, the motor characteristics are tailored to those applications. Also, since there is extensive use of adjustable frequency inverters in these applications, there is the opportunity to design for an optimal pole number and operate at other than 60 Hz frequency when inverters are utilized. Designs with four and eight pole configurations were prototyped as part of this work. Four pole motors are the most commonly used configuration in induction motors today. The results of the prototype design, fabrication, and testing were quite successful. The 50 HP rating met all of the design goals including efficiency and power density. Tested values of motor losses at 50 HP were 30% lower than energy efficient induction motors and the motor weight is 35% lower than the energy efficient induction motor of the same rating. Further, when tested at the 30 HP rating that is normally built in this 286T frame size, the efficiency far exceeds the project design goals with 30 HP efficiency levels indicating a 55% reduction in loss compared to energy efficient motors with a motor weight that is a few percentage points lower than the energy efficient motor. This 30 HP rating full load efficiency corresponds to a 46% reduction in loss compared to a 30 HP NEMA Premium? efficient motor. The cost goals were to provide a two year or shorter efficiency-based payback of a price premium associated with the magnet cost in these motors. That goal is based on 24/7 operation with a cost of electricity of 10 cents per kW-hr. Similarly, the 250 HP prototype efficiency testing was quite successful. In this case, the efficiency was maximized with a slightly less aggressive reduction in active material. The measured full load efficiency of 97.6% represents in excess of a 50% loss reduction compared to the equivalent NEMA Premium Efficiency induction motor. The active material weight reduction was a respectable 14.5% figure. This larger rating demonstrated both the scalability of this technology and also the ability to flexibly trade off power density and efficiency. In terms of starting performance, the 30 ? 50 HP prototypes were very extensively tested. The demonstrated capability included the ability to successfully start a load with an inertia of 25 times the motor?s own inertia while accelerating against a load torque following a fan profile at the motor?s full nameplate power rating. This capability will provide very wide applicability of this motor technology. The 250 HP prototype was also tested for starting characteristics, though without a coupled inertia and load torque. As a result it was not definitively proven that the same 25 times the motor?s own inertia could be started and synchronized successfully at 250 HP. Finite element modeling implies that this load could be successfully started, but it has not yet been confirmed by a test.

Melfi, Michael J.; Schiferl, Richard F.; Umans, Stephen D.

2013-03-12T23:59:59.000Z

296

Counterrotating brushless dc permanent magnet motor  

DOE Patents (OSTI)

An brushless DC permanent magnet motor is provided for driving an autonomous underwater vehicle. In one embodiment, the motor comprises four substantially flat stators disposed in stacked relationship, with pairs of the stators being axially spaced and each of the stators comprising a tape-wound stator coil; and a first and second substantially flat rotors disposed between the spaced pairs of stators. Each of the rotors includes an annular array of permanent magnets embedded therein. A first shaft is connected to the first rotor and a second, concentric shaft is connected to the second rotor, and drive unit causes rotation of the two shafts in opposite directions. The second shaft comprises a hollow tube having a central bore therein in which the first shaft is disposed. Two different sets of bearings support the first and second shAfts. In another embodiment, the motor comprises two ironless stators and pairs and rotors mounted no opposite sides of the stators and driven by counterrotating shafts.

Hawsey, R.A.; Bailey, J.M.

1990-12-31T23:59:59.000Z

297

Counterrotating brushless dc permanent magnet motor  

DOE Patents (OSTI)

An brushless DC permanent magnet motor is provided for driving an autonomous underwater vehicle. In one embodiment, the motor comprises four substantially flat stators disposed in stacked relationship, with pairs of the stators being axially spaced and each of the stators comprising a tape-wound stator coil; and a first and second substantially flat rotors disposed between the spaced pairs of stators. Each of the rotors includes an annular array of permanent magnets embedded therein. A first shaft is connected to the first rotor and a second, concentric shaft is connected to the second rotor, and drive unit causes rotation of the two shafts in opposite directions. The second shaft comprises a hollow tube having a central bore therein in which the first shaft is disposed. Two different sets of bearings support the first and second shAfts. In another embodiment, the motor comprises two ironless stators and pairs and rotors mounted no opposite sides of the stators and driven by counterrotating shafts.

Hawsey, R.A.; Bailey, J.M.

1990-01-01T23:59:59.000Z

298

Myers Motors | Open Energy Information  

Open Energy Info (EERE)

Myers Motors Myers Motors Jump to: navigation, search Name Myers Motors Place Tallmadge, Ohio Zip 44278 Sector Vehicles Product Myers Motors produces three wheeled electric vehicles. Coordinates 41.10294°, -81.440864° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":41.10294,"lon":-81.440864,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

299

AQWON Motors | Open Energy Information  

Open Energy Info (EERE)

AQWON Motors AQWON Motors Jump to: navigation, search Name AQWON-Motors Place Speinshart, Germany Zip 92676 Sector Hydro, Hydrogen Product AQWON-Motors has developed the first hydrogen powered 2 stroke-engine scooter. It has been approved by the German TÃœVÂ (the official technical inspection agency). Coordinates 49.78699°, 11.820385° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":49.78699,"lon":11.820385,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

300

General Motors | Open Energy Information  

Open Energy Info (EERE)

description http:www.nrel.govnewspress2006375.html LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now General Motors is a company located in...

Note: This page contains sample records for the topic "includes finished motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Tesla Motors | Open Energy Information  

Open Energy Info (EERE)

Tesla Motors Tesla Motors Jump to: navigation, search Logo: Tesla Motors Name Tesla Motors Address 1050 Bing Street Place San Carlos, California Zip 94070 Sector Vehicles Product Produces electric vehicles Website http://www.teslamotors.com/ Coordinates 37.496737°, -122.245323° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":37.496737,"lon":-122.245323,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

302

Brushed permanent magnet DC MLC motor operation in an external magnetic field  

SciTech Connect

Purpose: Linac-MR systems for real-time image-guided radiotherapy will utilize the multileaf collimators (MLCs) to perform conformal radiotherapy and tumor tracking. The MLCs would be exposed to the external fringe magnetic fields of the linac-MR hybrid systems. Therefore, an experimental investigation of the effect of an external magnetic field on the brushed permanent magnet DC motors used in some MLC systems was performed. Methods: The changes in motor speed and current were measured for varying external magnetic field strengths up to 2000 G generated by an EEV electromagnet. These changes in motor characteristics were measured for three orientations of the motor in the external magnetic field, mimicking changes in motor orientations due to installation and/or collimator rotations. In addition, the functionality of the associated magnetic motor encoder was tested. The tested motors are used with the Varian 120 leaf Millennium MLC (Maxon Motor half leaf and full leaf motors) and the Varian 52 leaf MKII MLC (MicroMo Electronics leaf motor) including a carriage motor (MicroMo Electronics). Results: In most cases, the magnetic encoder of the motors failed prior to any damage to the gearbox or the permanent magnet motor itself. This sets an upper limit of the external magnetic field strength on the motor function. The measured limits of the external magnetic fields were found to vary by the motor type. The leaf motor used with a Varian 52 leaf MKII MLC system tolerated up to 450{+-}10 G. The carriage motor tolerated up to 2000{+-}10 G field. The motors used with the Varian 120 leaf Millennium MLC system were found to tolerate a maximum of 600{+-}10 G. Conclusions: The current Varian MLC system motors can be used for real-time image-guided radiotherapy coupled to a linac-MR system, provided the fringe magnetic fields at their locations are below the determined tolerance levels. With the fringe magnetic fields of linac-MR systems expected to be larger than the tolerance levels determined, some form of magnetic shielding would be required.

Yun, J.; St Aubin, J.; Rathee, S.; Fallone, B. G. [Department of Physics, University of Alberta, 11322-89 Avenue, Edmonton, Alberta T6G 2G7 (Canada) and Department of Oncology, Medical Physics Division, University of Alberta, 11560 University Avenue, Edmonton, Alberta T6G 1Z2 (Canada); Department of Medical Physics, Cross Cancer Institute, 11560 University Avenue, Edmonton, Alberta T6G 1Z2 (Canada) and Department of Oncology, Medical Physics Division, University of Alberta, 11560 University Avenue, Edmonton, Alberta T6G 1Z2 (Canada); Department of Physics, University of Alberta, 11322-89 Avenue, Edmonton, Alberta T6G 2G7 (Canada); Department of Medical Physics, Cross Cancer Institute, 11560 University Avenue, Edmonton, Alberta T6G 1Z2 (Canada) and Department of Oncology, Medical Physics Division, University of Alberta, 11560 University Avenue, Edmonton, Alberta T6G 1Z2 (Canada)

2010-05-15T23:59:59.000Z

303

Finishing and Special Motifs: Lessons Learned from CRISPR Analysis Using Next-Generation Draft Sequences ( 7th Annual SFAF Meeting, 2012)  

SciTech Connect

Catherine Campbell on "Finishing and Special Motifs: Lessons learned from CRISPR analysis using next-generation draft sequences" at the 2012 Sequencing, Finishing, Analysis in the Future Meeting held June 5-7, 2012 in Santa Fe, New Mexico.

Campbell, Catherine [Noblis

2012-06-01T23:59:59.000Z

304

Comparison and Analysis of Classical Motor with Amorphous Iron Motor Based on Ansoft  

Science Conference Proceedings (OSTI)

At present, various types of motors of total power is up to 420 million kilowatts and the consumption accounts for 60% of country's total electricity. The motor is high cost, energy consumption and so on while it is produced using traditional materials ... Keywords: Ansoft, amorphous iron motor, motor modeling, motor simulation

Jianwei Leng; Ting Liu

2010-08-01T23:59:59.000Z

305

Transport Characteristics of Molecular Motors  

E-Print Network (OSTI)

Properties of transport of molecular motors are investigated. A simplified model based on the concept of Brownian ratchets is applied. We analyze a stochastic equation of motion by means of numerical methods. The transport is systematically studied with respect to its energetic efficiency and quality expressed by an effective diffusion coefficient. We demonstrate the role of friction and non-equilibrium driving on the transport quantifiers and identify regions of a parameter space where motors are optimally transported.

Machura, Lukasz; Luczka, Jerzy; 10.1016/j.biosystems.2008.05.033

2011-01-01T23:59:59.000Z

306

Electric motor systems in developing countries: Opportunities for efficiency improvement  

SciTech Connect

This report presents an overview of the current status and efficiency improvement potential of industrial motor systems in developing countries. Better management of electric motor systems is of particular relevance in developing countries, where improved efficiency can lead to increased productivity and slower growth in electricity demand. Motor systems currently consume some 65--80% of the industrial electricity in developing countries. Drawing on studies from Thailand, India, Brazil, China, Pakistan, and Costa Rica, we describe potential efficiency gains in various parts of the motor system, from the electricity delivery system through the motor to the point where useful work is performed. We report evidence of a significant electricity conservation potential. Most of the efficiency improvement methods we examine are very cost-effective from a societal viewpoint, but are generally not implemented due to various barriers that deter their adoption. Drawing on experiences in North America, we discuss a range of policies to overcome these barriers, including education, training, minimum efficiency standards, motor efficiency testing protocols, technical assistance programs, and financial incentives.

Meyers, S.; Monahan, P.; Lewis, P.; Greenberg, S. [Lawrence Berkeley Lab., CA (United States); Nadel, S. [American Council for an Energy-Efficient Economy, Washington, DC (United States)

1993-08-01T23:59:59.000Z

307

Obstacles and Opportunity: Turbine Motorization in Refineries Today  

E-Print Network (OSTI)

Steam turbines have been widely used in oil refineries for driving pumps, compressors and other rotary machines. However, in recent years, the authors of this paper have seen substantial turbine motorization projects completed or being planned in the refineries. This paper discusses the key aspects that should be considered in evaluating the feasibility of motorization projects. Based on the literature review and a refinery survey conducted by the authors, the key factors include the critical level of the related equipment, the potential energy savings and capital cost, the steam and power balance in the related area, and the reliability in the refinery's power supply. Based on the authors' experience, the utilities' energy efficiency incentive programs in California also influence the decision-making process for turbine motorization projects. Therefore, this paper includes a description of the utilities' guidelines for fuel substitution projects. In particular, the utilities' three-prong requirements on net source-BTU energy savings, cost effectiveness, and avoidance of adverse impacts to the environment are discussed. Two real life case studies are presented to demonstrate how the above criteria should be applied for determining if a motorization opportunity is economically viable. A discussion on suggested features is also included for prescreening turbine motorization project candidates for better energy and environment economics such as venting of exhaust steam from a back pressure turbine and oversized design of the existing turbine and pump.

Feng, Hua; Liu, Jinghing; Liu, Xiang; Ahmad, Mushtaq; Deng, Alan

2012-01-01T23:59:59.000Z

308

Heat engine and electric motor torque distribution strategy for a hybrid electric vehicle  

DOE Patents (OSTI)

A method is provided for controlling a power train system for a hybrid electric vehicle. The method includes a torque distribution strategy for controlling the engine and the electric motor. The engine and motor commands are determined based upon the accelerator position, the battery state of charge and the amount of engine and motor torque available. The amount of torque requested for the engine is restricted by a limited rate of rise in order to reduce the emissions from the engine. The limited engine torque is supplemented by motor torque in order to meet a torque request determined based upon the accelerator position.

Boberg, Evan S. (Hazel Park, MI); Gebby, Brian P. (Hazel Park, MI)

1999-09-28T23:59:59.000Z

309

Coexistence and efficiency of normal and anomalous transport by molecular motors in living cells  

E-Print Network (OSTI)

Recent experiments reveal both passive subdiffusion of various nanoparticles and anomalous active transport of such particles by molecular motors in the molecularly crowded environment of living biological cells. Passive and active microrheology reveals that the origin of this anomalous dynamics is due to the viscoelasticity of the intracellular fluid. How do molecular motors perform in such a highly viscous, dissipative environment? Can we explain the observed co-existence of the anomalous transport of relatively large particles of 100 to 500 nm in size by kinesin motors with the normal transport of smaller particles by the same molecular motors? What is the efficiency of molecular motors in the anomalous transport regime? Here we answer these seemingly conflicting questions and consistently explain experimental findings in a generalization of the well-known continuous diffusion model for molecular motors with two conformational states in which viscoelastic effects are included.

Igor Goychuk; Vasyl O. Kharchenko; R. Metzler

2013-09-26T23:59:59.000Z

310

EERE-2010-BT-STD-0027 Ex Parte Letter NEMA Motor Training re DOE Motors  

NLE Websites -- All DOE Office Websites (Extended Search)

0-BT-STD-0027 Ex Parte Letter NEMA Motor Training re DOE 0-BT-STD-0027 Ex Parte Letter NEMA Motor Training re DOE Motors Rule 15 July 2013. EERE-2010-BT-STD-0027 Ex Parte Letter NEMA Motor Training re DOE Motors Rule 15 July 2013. This memorandum memorializes a communication between DOE staff and members of the NEMA Motor and Generator Section in connection with this proceeding. NEMA thanks the DOE for the opportunity to conduct training for DOE staff and its consultants on July 15th, 2013 which illustrated the different types of motors, motor construction theory and motor applications by type. It is our hope that better understanding of motor types and construction will assist the Department and its consultants with the discharge of their duties. EERE-2010-BT-STD-0027 Ex Parte Letter NEMA Motor Training re DOE Motors

311

Conducting a Motor Survey: Key Step for Establishing a Motor Management Policy  

E-Print Network (OSTI)

Roughly 70% of the energy consumed by manufacturing processes is used by electric motors. According to the U.S. Department of Energy, greater attention to motor systems management can reduce motor-related energy costs by 18%. Establishing a motor management policy is therefore an essential task for any plant manager or engineer concerned with minimizing motor (and process) downtime and reducing energy costs. In order to develop an effective motor policy, a manager needs information on the number and condition of motors in use. A targeted motor survey will collect data on a representative sample of a plant's motor population. This survey information will then provide a basis for further development of the motor policy. This paper discusses the process of conducting a motor survey. It identifies the type of information to be collected, along with a methodology for selecting appropriate sample motors for more detailed investigations.

Miller, R. B.

2002-04-01T23:59:59.000Z

312

Crude oil and finished fuel storage stability: An annotated review  

DOE Green Energy (OSTI)

A state-of-the-art review and assessment of storage effects on crude oil and product quality was undertaken through a literature search by computer accessing several data base sources. Pertinent citations from that literature search are tabulated for the years 1980 to the present. This 1990 revision supplements earlier reviews by Brinkman and others which covered stability publications through 1979 and an update in 1983 by Goetzinger and others that covered the period 1952--1982. For purposes of organization, citations are listed in the current revision chronologically starting with the earliest 1980 publications. The citations have also been divided according to primary subject matter. Consequently 11 sections appear including: alternate fuels, gasoline, distillate fuel, jet fuel, residual fuel, crude oil, biodegradation, analyses, reaction mechanisms, containment, and handling and storage. Each section contains a brief narrative followed by all the citations for that category.

Whisman, M.L.; Anderson, R.P.; Woodward, P.W.; Giles, H.N.

1991-01-01T23:59:59.000Z

313

Submersible canned motor transfer pump  

DOE Patents (OSTI)

A transfer pump is described which is used in a waste tank for transferring high-level radioactive liquid waste from a waste tank and having a column assembly, a canned electric motor means, and an impeller assembly with an upper impeller and a lower impeller connected to a shaft of a rotor assembly. The column assembly locates a motor housing with the electric motor means adjacent to the impeller assembly which creates an hydraulic head, and which forces the liquid waste, into the motor housing to cool the electric motor means and to cool and/or lubricate the radial and thrust bearing assemblies. Hard-on-hard bearing surfaces of the bearing assemblies and a ring assembly between the upper impeller and electric motor means grind large particles in the liquid waste flow. Slots in the static bearing member of the radial bearing assemblies further grind down the solid waste particles so that only particles smaller than the clearances in the system can pass there through, thereby resisting damage to and the interruption of the operation of the transfer pump. The column assembly is modular so that sections can be easily assembled, disassembled and/or removed. A second embodiment employs a stator jacket which provides an alternate means for cooling the electric motor means and lubricating and/or cooling the bearing assemblies, and a third embodiment employs a variable level suction device which allows liquid waste to be drawn into the transfer pump from varying and discrete levels in the waste tank. 17 figs.

Guardiani, R.F.; Pollick, R.D.; Nyilas, C.P.; Denmeade, T.J.

1997-08-19T23:59:59.000Z

314

System and method to determine electric motor efficiency nonintrusively  

Science Conference Proceedings (OSTI)

A system and method for nonintrusively determining electric motor efficiency includes a processor programed to, while the motor is in operation, determine a plurality of stator input currents, electrical input data, a rotor speed, a value of stator resistance, and an efficiency of the motor based on the determined rotor speed, the value of stator resistance, the plurality of stator input currents, and the electrical input data. The determination of the rotor speed is based on one of the input power and the plurality of stator input currents. The determination of the value of the stator resistance is based on at least one of a horsepower rating and a combination of the plurality of stator input currents and the electrical input data. The electrical input data includes at least one of an input power and a plurality of stator input voltages.

Lu, Bin (Kenosha, WI); Habetler, Thomas G. (Snellville, GA); Harley, Ronald G. (Lawrenceville, GA)

2011-08-30T23:59:59.000Z

315

System and method for determining stator winding resistance in an AC motor  

Science Conference Proceedings (OSTI)

A system and method for determining stator winding resistance in an AC motor is disclosed. The system includes a circuit having an input connectable to an AC source and an output connectable to an input terminal of an AC motor. The circuit includes at least one contactor and at least one switch to control current flow and terminal voltages in the AC motor. The system also includes a controller connected to the circuit and configured to modify a switching time of the at least one switch to create a DC component in an output of the system corresponding to an input to the AC motor and determine a stator winding resistance of the AC motor based on the injected DC component of the voltage and current.

Lu, Bin (Kenosha, WI); Habetler, Thomas G. (Snellville, GA); Zhang, Pinjia (Atlanta, GA); Theisen, Peter J. (West Bend, WI)

2011-05-31T23:59:59.000Z

316

The infant motor profile : a standardized and qualitative assessment of motor bahaviour in infancy.  

E-Print Network (OSTI)

??This thesis presents the Infant Motor Profile (IMP), a new, video-based qualitative assessment of motor behaviour of infants aged 3 to 18 months. The IMP (more)

Heineman, Kirsten Roselien

2010-01-01T23:59:59.000Z

317

Project Plan Remove Special Nuclear Material (SNM) from Plutonium Finishing Plant (PFP) Project  

Science Conference Proceedings (OSTI)

This plan presents the overall objectives, description, justification and planning for the Plutonium Finishing Plant (PFP) Remove SNM Materials. The intent of this plan is to describe how this project will be managed and integrated with other facility stabilization and deactivation activities. This plan supplements the overall integrated plan presented in the Plutonium Finishing Plant Integrated Project Management Plan (IPMP), HNF-3617, Rev.0. This project plan is the top-level definitive project management document for the PFP Remove SNM Materials project. It specifies the technical, schedule, requirements and the cost baseline to manage the execution of the Remove SNM Materials project. Any deviation to the document must be authorized through the appropriate change control process. The Remove SNM Materials project provides the necessary support and controls required for DOE-HQ, DOE-RL, BWHC, and other DOE Complex Contractors the path forward to negotiate shipped/receiver agreements, schedule shipments, and transfer material out of PFP to enable final deactivation.

BARTLETT, W.D.

1999-09-14T23:59:59.000Z

318

Motor monitoring method and apparatus using high frequency ...  

A motor current analysis method and apparatus for monitoring electrical-motor-driven devices. The method and apparatus utilize high frequency portions of the motor ...

319

Carbonyl Emissions from Gasoline and Diesel Motor Vehicles  

E-Print Network (OSTI)

Carbonyl compounds present in motor vehicle exhaust, rangingfrom gasoline and diesel motor vehicles. Environ. Sci. Tech.composition and toxicity of motor vehicle emission samples.

Jakober, Chris A.

2008-01-01T23:59:59.000Z

320

Mechanisms of motor activity regulation in axonal transport  

E-Print Network (OSTI)

emerging principles of kinesin motor utilization." Annu Revopposite-polarity microtubule motors." J Cell Biol 156( 4):Kinesin mutations cause motor neuron disease phenotypes by

Reis, Gerald Feliz

2008-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "includes finished motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

VIA Motors electric vehicle platform | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

VIA Motors electric vehicle platform VIA Motors electric vehicle platform extended range electric vehicle technologies VIA Motors electric vehicle platform More Documents &...

322

Demand, Supply, and Price Outlook for Reformulated Motor Gasoline 1995  

U.S. Energy Information Administration (EIA)

benzene extracted from the reformulated motor gasoline pool in their conventional motor gasoline. Importers lacking 1990 motor gasoline quality data with which to

323

Building Energy Software Tools Directory: MotorMaster+  

NLE Websites -- All DOE Office Websites (Extended Search)

implement an effective energy management program. MotorMaster+ contains a motor inventory module, where motor nameplate data is stored and linked to utility, facility, plant...

324

Lab 4 -Motor Constants and Sensor Calibration Consider a DC servo motor which is connected to a power supply. The motor inertia is Jm. The rotational  

E-Print Network (OSTI)

Lab 4 - Motor Constants and Sensor Calibration PRE-LAB Consider a DC servo motor which is connected to a power supply. The motor inertia is Jm. The rotational damping in the motor is bm. The motor produces a torque Tm = Kmi where Km is the motor's torque constant and i is the current from the power supply. a

Stanford University

325

Plan for the Startup of HA-21I Furnace Operations at the Plutonium Finishing Plant (PFP)  

Science Conference Proceedings (OSTI)

Achievement of Thermal Stabilization mission elements require the installation and startup of three additional muffle furnaces for the thermal stabilization of plutonium and plutonium bearing materials at the Plutonium Finishing Plant (PFP). The release to operate these additional furnaces will require an Activity Based Startup Review. The conduct of the Activity Based Startup Review (ABSR) was approved by Fluor Daniel Hanford on October 15, 1999. This plan has been developed with the objective of identifying those activities needed to guide the controlled startup of five furnaces from authorization to unrestricted operations by adding the HA-211 furnaces in an orderly and safe manner after the approval to Startup has been given. The Startup Plan provides a phased approach that bridges the activities between the completion of the Activity Based Startup Review authorizing the use of the three additional furnaces and the unrestricted operation of the five thermal stabilization muffle furnaces. The four phases are: (1) the initiation of five furnace operations using three empty (simulated full) boat charges from HA-211 and two full charges from HC-21C; (2) three furnace operations (one full charge from HA-211 and two full charges from HC-21C); (3) four furnace operations (two full charges from HA-211 and two full charges from HC-21C); and (4) integrated five furnace operations and unrestricted operations. Phase 1 of the Plan will be considered as the cold runs. This Plan also provides management oversight and administrative controls that are to be implemented until unrestricted operations are authorized. It also provides a formal review process for ensuring that all preparations needed for full five furnace operations are completed and formally reviewed prior to proceeding to the increased activity levels associated with five furnace operations. Specific objectives include: (1) To ensure that activities are conducted in a safe manner. (2) To provide supplemental technical and managerial support to Thermal Stabilization activities during the initial use of the HA-211 Furnaces until the commencement of full five furnace, unrestricted operations. (3) Ensure that operations can be conducted in a manner that meets PFP and DOE expectations associated with the principles of integrated safety management. (4) To ensure that all interfacing activities needed to meet Thermal Stabilization mission objectives are completed.

WILLIS, H.T.

2000-02-17T23:59:59.000Z

326

Plutonium Finishing Plan (PFP) Treatment and Storage Unit Interim Status Closure Plan  

Science Conference Proceedings (OSTI)

This document describes the planned activities and performance standards for closing the Plutonium Finishing Plant (PFP) Treatment and Storage Unit. The PFP Treatment and Storage Unit is located within the 234-52 Building in the 200 West Area of the Hanford Facility. Although this document is prepared based upon Title 40 Code of Federal Regulations (CFR), Part 265, Subpart G requirements, closure of the unit will comply with Washington Administrative Code (WAC) 173-303-610 regulations pursuant to Section 5.3 of the Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement) Action Plan (Ecology et al. 1996). Because the PFP Treatment and Storage Unit manages transuranic mixed (TRUM) waste, there are many controls placed on management of the waste. Based on the many controls placed on management of TRUM waste, releases of TRUM waste are not anticipated to occur in the PFP Treatment and Storage Unit. Because the intention is to clean close the PFP Treatment and Storage Unit, postclosure activities are not applicable to this closure plan. To clean close the unit, it will be demonstrated that dangerous waste has not been left onsite at levels above the closure performance standard for removal and decontamination. If it is determined that clean closure is not possible or is environmentally impractical, the closure plan will be modified to address required postclosure activities. The PFP Treatment and Storage Unit will be operated to immobilize and/or repackage plutonium-bearing waste in a glovebox process. The waste to be processed is in a solid physical state (chunks and coarse powder) and will be sealed into and out of the glovebox in closed containers. The containers of immobilized waste will be stored in the glovebox and in additional permitted storage locations at PFP. The waste will be managed to minimize the potential for spills outside the glovebox, and to preclude spills from reaching soil. Containment surfaces will be maintained to ensure integrity. In the unlikely event that a waste spill does occur outside the glovebox, operating methods and administrative controls will require that waste spills be cleaned up promptly and completely, and a notation will be made in the operating record. Because dangerous waste does not include source, special nuclear, and by-product material components of mixed waste, radionuclides are not within the scope of this documentation. The information on radionuclides is provided only for general knowledge.

PRIGNANO, A.L.

2000-07-01T23:59:59.000Z

327

Plutonium Finishing Plant (PFP) Standards/Requirements Identification Document (S/RID)  

Science Conference Proceedings (OSTI)

This Standards/Requirements Identification Document (S/RID) sets forth the Environmental Safety and Health (ESH) standards/requirements for the Plutonium Finishing Plant (PFP). This S/RID is applicable to the appropriate life cycle phases of design, construction, operation, and preparation for decommissioning. These standards/requirements are adequate to ensure the protection of the health and safety of workers, the public, and the environment.

Maddox, B.S.

1996-01-01T23:59:59.000Z

328

Motor gasolines, winter 1982-83  

Science Conference Proceedings (OSTI)

Analytical data for 1330 samples of motor gasoline, were collected from service stations throughout the country and were analyzed in the laboratories of various refiners, motor manufacturers, and chemical companies. The data were submitted to the Bartlesville Energy Technology Center for study, necessary calculations, and compilation under a cooperative agreement between the Bartlesville Energy Technology Center (BETC) and the American Petroleum Institute (API). The samples represent the products of 28 companies, large and small, which manufacture and supply gasoline. These data are tabulated by groups according to brands (unlabeled) and grades for 17 marketing districts into which the country is divided. A map included in this report, shows marketing areas, districts and sampling locations. The report also includes charts indicating the trends of selected properties of motor fuels since winter 1959-1960 survey for the leaded gasolines, and since winter 1979-1980 survey for the unleaded gasolines. Sixteen octane distribution percent charts for areas 1, 2, 3, and 4 for unleaded antiknock index (R + M)/2 below 90.0, unleaded antiknock index (R + M/2 90.0 and above, leaded antiknock index (R + M)/2 below 93.0, and leaded antiknock index (R + M)/2 93.0 and above grades of gasoline are presented in this report. The antiknock (octane) index (R + M)/2 averages of gasoline sold in this country were 87.3 for unleaded below 90.0, 91.5 for unleaded 90.0 and above, and 89.1 for leaded below 93.0, and no data was reported in this report for leaded gasolines with an antiknock index (R + M)/2 93.0 and above. 21 figures, 5 tables.

Shelton, E.M.

1983-07-01T23:59:59.000Z

329

Appendix F Cultural Resources, Including  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Appendix F Appendix F Cultural Resources, Including Section 106 Consultation STATE OF CALIFORNIA - THE RESOURCES AGENCY EDMUND G. BROWN, JR., Governor OFFICE OF HISTORIC PRESERVATION DEPARTMENT OF PARKS AND RECREATION 1725 23 rd Street, Suite 100 SACRAMENTO, CA 95816-7100 (916) 445-7000 Fax: (916) 445-7053 calshpo@parks.ca.gov www.ohp.parks.ca.gov June 14, 2011 Reply in Reference To: DOE110407A Angela Colamaria Loan Programs Office Environmental Compliance Division Department of Energy 1000 Independence Ave SW, LP-10 Washington, DC 20585 Re: Topaz Solar Farm, San Luis Obispo County, California Dear Ms. Colamaria: Thank you for seeking my consultation regarding the above noted undertaking. Pursuant to 36 CFR Part 800 (as amended 8-05-04) regulations implementing Section

330

Mission Motors | Open Energy Information  

Open Energy Info (EERE)

Motors Motors Jump to: navigation, search Name Mission Motors Place San Francisco, California Sector Vehicles Product Electric Motorcycles Year founded 2007 Number of employees 11-50 Website http://www.ridemission.com/ Coordinates 37.7749295°, -122.4194155° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":37.7749295,"lon":-122.4194155,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

331

Aptera Motors | Open Energy Information  

Open Energy Info (EERE)

Aptera Motors Aptera Motors Jump to: navigation, search Name Aptera Motors Address 2778 Loker Avenue West Place Carlsbad, California Zip 92008 Sector Vehicles Product Aims to to make an aerodynamic two-seater hybrid electric vehicle Website http://www.aptera.com/ Coordinates 33.1412124°, -117.3205123° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":33.1412124,"lon":-117.3205123,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

332

The Allocation of the Social Costs of Motor-Vehicle Use to Six Classes of Motor Vehicles  

E-Print Network (OSTI)

alcohol Unfinished oils Motor gasoline blending componentsalcohol Unfinished oils Motor gasoline blending componentsthe Use of Persian-Gulf Oil for Motor Vehicles (M. Delucchi

Delucchi, Mark A.

1996-01-01T23:59:59.000Z

333

Countries Gasoline Prices Including Taxes  

Gasoline and Diesel Fuel Update (EIA)

Countries (U.S. dollars per gallon, including taxes) Countries (U.S. dollars per gallon, including taxes) Date Belgium France Germany Italy Netherlands UK US 01/13/14 7.83 7.76 7.90 8.91 8.76 8.11 3.68 01/06/14 8.00 7.78 7.94 8.92 8.74 8.09 3.69 12/30/13 NA NA NA NA NA NA 3.68 12/23/13 NA NA NA NA NA NA 3.63 12/16/13 7.86 7.79 8.05 9.00 8.78 8.08 3.61 12/9/13 7.95 7.81 8.14 8.99 8.80 8.12 3.63 12/2/13 7.91 7.68 8.07 8.85 8.68 8.08 3.64 11/25/13 7.69 7.61 8.07 8.77 8.63 7.97 3.65 11/18/13 7.99 7.54 8.00 8.70 8.57 7.92 3.57 11/11/13 7.63 7.44 7.79 8.63 8.46 7.85 3.55 11/4/13 7.70 7.51 7.98 8.70 8.59 7.86 3.61 10/28/13 8.02 7.74 8.08 8.96 8.79 8.04 3.64 10/21/13 7.91 7.71 8.11 8.94 8.80 8.05 3.70 10/14/13 7.88 7.62 8.05 8.87 8.74 7.97 3.69

334

Mercury: Next-gen Data Analysis and Annotation Pipeline (Seventh Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting 2012)  

Science Conference Proceedings (OSTI)

David Sexton (Baylor) gives a talk titled "Mercury: Next-gen Data Analysis and Annotation Pipeline" at the 7th Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting held in June, 2012 in Santa Fe, NM.

Sexton, David (Baylor)

2012-06-01T23:59:59.000Z

335

Deep Frying: Chemistry, Nutrition and Practical ApplicationsChapter 2 Storage and Handling of Finished Frying Oils  

Science Conference Proceedings (OSTI)

Deep Frying: Chemistry, Nutrition and Practical Applications Chapter 2 Storage and Handling of Finished Frying Oils Food Science Health Nutrition Biochemistry eChapters Food Science & Technology Health - Nutrition - Biochemistry Pres

336

Introducing National Center for Genome Resources (NCGR) Informatics (Seventh Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting 2012)  

Science Conference Proceedings (OSTI)

John Crow from the National Center for Genome Resources discusses his organization's informatics at the 7th Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting held in June, 2012 in Santa Fe, NM.

Crow, John [National Center for Genome Resources

2012-06-01T23:59:59.000Z

337

High Throughput Plasmid Sequencing with Illumina and CLC Bio (Seventh Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting 2012)  

Science Conference Proceedings (OSTI)

Ajay Athavale (Monsanto) presents "High Throughput Plasmid Sequencing with Illumina and CLC Bio" at the 7th Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting held in June, 2012 in Santa Fe, NM.

Athavale, Ajay [Monsanto

2012-06-01T23:59:59.000Z

338

The PerkinElmer Omics Laboratory (Seventh Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting 2012)  

Science Conference Proceedings (OSTI)

Todd Smith of the PerkinElmer Omics Laboratory gives a talk about his lab and its work at the 7th Annual Sequencing, Finishing, Analysis in the Future (SFAF) Meeting held in June, 2012 in Santa Fe, NM.

Smith, Todd [PerkinElmer Omics Laboratory

2012-06-01T23:59:59.000Z

339

Thermoelectric generator for motor vehicle  

DOE Patents (OSTI)

A thermoelectric generator for producing electric power for a motor vehicle from the heat of the exhaust gasses produced by the engine of the motor vehicle. The exhaust gasses pass through a finned heat transfer support structure which has seat positions on its outside surface for the positioning of thermoelectric modules. A good contact cylinder provides a framework from which a spring force can be applied to the thermoelectric modules to hold them in good contact on their seats on the surface of the heat transfer support structure.

Bass, John C. (6121 La Pintra Dr., La Jolla, CA 92037)

1997-04-29T23:59:59.000Z

340

Homopolar motor with dual rotors  

DOE Patents (OSTI)

A homopolar motor has a field rotor mounted on a frame for rotation in a first rotational direction and for producing an electromagnetic field, and an armature rotor mounted for rotation on said frame within said electromagnetic field and in a second rotational direction counter to said first rotational direction of said field rotor. The two rotors are coupled through a 1:1 gearing mechanism, so as to travel at the same speed but in opposite directions. This doubles the output voltage and output power, as compared to a motor in which only the armature is rotated. Several embodiments are disclosed. 7 figs.

Hsu, J.S.

1998-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "includes finished motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

IEMDC IN-LINE ELECTRIC MOTOR DRIVEN COMPRESSOR  

SciTech Connect

This report contains the final project summary and deliverables required by the award for the development of an In-line Electric Motor Driven Compressor (IEMDC). Extensive work was undertaken during the course of the project to develop the motor and the compressor section of the IEMDC unit. Multiple design iterations were performed to design an electric motor for operation in a natural gas environment and to successfully integrate the motor with a compressor. During the project execution, many challenges were successfully overcome in order to achieve the project goals and to maintain the system design integrity. Some of the challenges included limiting the magnitude of the compressor aerodynamic loading for appropriate sizing of the magnetic bearings, achieving a compact motor rotor size to meet the rotor dynamic requirements of API standards, devising a motor cooling scheme using high pressure natural gas, minimizing the impact of cooling on system efficiency, and balancing the system thrust loads for the magnetic thrust bearing. Design methods that were used on the project included validated state-of-the-art techniques such as finite element analysis and computational fluid dynamics along with the combined expertise of both Curtiss-Wright Electro-Mechanical Corporation and Dresser-Rand Company. One of the most significant areas of work undertaken on the project was the development of the unit configuration for the system. Determining the configuration of the unit was a significant step in achieving integration of the electric motor into a totally enclosed compression system. Product review of the IEMDC unit configuration was performed during the course of the development process; this led to an alternate design configuration. The alternate configuration is a modular design with the electric motor and compressor section each being primarily contained in its own pressure containing case. This new concept resolved the previous conflict between the aerodynamic flow passage requirements and electric motor requirements for support and utilities by bounding the flowpath within the compressor section. However most importantly, the benefits delivered by the new design remained the same as those proposed by the goals of the project. In addition, this alternate configuration resulted in the achievement of a few additional advantages over the original concept such as easier maintenance, operation, and installation. Interaction and feedback solicited from target clients regarding the unit configuration supports the fact that the design addresses industry issues regarding accessibility, maintainability, preferred operating practice, and increased reliability.

Michael J. Crowley; Prem N. Bansal

2004-10-01T23:59:59.000Z

342

Nominal Position Controller for Permanent Magnet Synchronous Motor System  

Science Conference Proceedings (OSTI)

A nonlinear position controller for permanent magnet synchronous motor (PMSM) was designed to achieve position tracing control and robust control. The controller included two parts: the model controller and the robust controller. The former was designed ... Keywords: PMSM, nominal control, sliding mode control

Yuzeng Zhang; Fan Wang; Mingyin Yan

2010-05-01T23:59:59.000Z

343

Magnetic levitation configuration incorporating levitation, guidance and linear synchronous motor  

DOE Patents (OSTI)

A propulsion and suspension system for an inductive repulsion type magnetically levitated vehicle which is propelled and suspended by a system which includes propulsion windings which form a linear synchronous motor and conductive guideways, adjacent to the propulsion windings, where both combine to partially encircling the vehicle-borne superconducting magnets. A three phase power source is used with the linear synchronous motor to produce a traveling magnetic wave which in conjunction with the magnets propel the vehicle. The conductive guideway combines with the superconducting magnets to provide for vehicle leviation.

Coffey, Howard T. (Darien, IL)

1993-01-01T23:59:59.000Z

344

Magnetic levitation configuration incorporating levitation, guidance and linear synchronous motor  

DOE Patents (OSTI)

A propulsion and suspension system for an inductive repulsion type magnetically levitated vehicle which is propelled and suspended by a system which includes propulsion windings which form a linear synchronous motor and conductive guideways, adjacent to the propulsion windings, where both combine to partially encircling the vehicle-borne superconducting magnets. A three phase power source is used with the linear synchronous motor to produce a traveling magnetic wave which in conjunction with the magnets propel the vehicle. The conductive guideway combines with the superconducting magnets to provide for vehicle levitation. 3 figures.

Coffey, H.T.

1993-10-19T23:59:59.000Z

345

Electrical motor/generator drive apparatus and method  

SciTech Connect

The present disclosure includes electrical motor/generator drive systems and methods that significantly reduce inverter direct-current (DC) bus ripple currents and thus the volume and cost of a capacitor. The drive methodology is based on a segmented drive system that does not add switches or passive components but involves reconfiguring inverter switches and motor stator winding connections in a way that allows the formation of multiple, independent drive units and the use of simple alternated switching and optimized Pulse Width Modulation (PWM) schemes to eliminate or significantly reduce the capacitor ripple current.

Su, Gui Jia

2013-02-12T23:59:59.000Z

346

Magnetic levitation configuration incorporating levitation, guidance and linear synchronous motor  

DOE Patents (OSTI)

A propulsion and suspension system for an inductive repulsion type magnetically levitated vehicle which is propelled and suspended by a system which includes propulsion windings which form a linear synchronous motor and conductive guideways, adjacent to the propulsion windings, where both combine to partially encircling the vehicle-borne superconducting magnets. A three phase power source is used with the linear synchronous motor to produce a traveling magnetic wave which in conjunction with the magnets propel the vehicle. The conductive guideway combines with the superconducting magnets to provide for vehicle leviation.

Coffey, H.T.

1992-12-31T23:59:59.000Z

347

Variable Frequency Drives: Energy Savings and Impact on Motor Performance  

E-Print Network (OSTI)

Variable frequency drives (VFDs) have found widespread application in recent years. VFDs are valued for their potential to save energy and improve processes. Reliability has improved significantly, but there are still pitfalls to be addressed in properly applying VFDs. The benefits and pitfalls in applying VFDs that will be addressed by this paper include- Benefits: Energy Savings, Improved Process Control, Soft Start Reduced Mechanical Stress, Improved Electrical System Power Factor, and Pitfalls: Motor Acoustic Noise, Motor Heating. This paper is intended for plant engineers and maintenance personnel who have some practical experience with electrical and mechanical equipment, but are not VFD experts.

Petro, D.

1993-03-01T23:59:59.000Z

348

Analysis of hunting in Synchronous Hysteresis Motor  

E-Print Network (OSTI)

The Synchronous Hysteresis Motor has an inherent instability when it is used to drive a gyroscope wheel. The motor ideally should spin at a constant angular velocity, but it instead sporadically oscillates about synchronous ...

Truong, Cang Kim, 1979-

2004-01-01T23:59:59.000Z

349

Hybrid vehicle motor alignment - Energy Innovation Portal  

A rotor of an electric motor for a motor vehicle is aligned to an axis of rotation for a crankshaft of an internal combustion engine having an internal combustion ...

350

Electric Motor Predictive Maintenance: Draft Guidelines  

Science Conference Proceedings (OSTI)

Predictive Maintenance can enhance the early detection and avoidance of incipient equipment failures in electric motors. This report provides draft guidelines to support the development of electric motor predictive maintenance (EMPM) programs at utility sites.

1997-10-16T23:59:59.000Z

351

Phenomenological analysis of ATP dependence of motor protein  

E-Print Network (OSTI)

In this study, through phenomenological comparison of the velocity-force data of processive motor proteins, including conventional kinesin, cytoplasmic dynein and myosin V, we found that, the ratio between motor velocities of two different ATP concentrations is almost invariant for any substall, superstall or negative external loads. Therefore, the velocity of motor can be well approximated by a Michaelis-Menten like formula $V=\\atp k(F)L/(\\atp +K_M)$, with $L$ the step size, and $k(F)$ the external load $F$ dependent rate of one mechanochemical cycle of motor motion in saturated ATP solution. The difference of Michaelis-Menten constant $K_M$ for substall, superstall and negative external load indicates, the ATP molecule affinity of motor head for these three cases are different, though the expression of $k(F)$ as a function of $F$ might be unchanged for any external load $F$. Verifications of this Michaelis-Menten like formula has also been done by fitting to the recent experimental data.

Yunxin Zhang

2011-08-09T23:59:59.000Z

352

Direct Lamination Cooling of Motors For Electric Vehicles  

DOE Green Energy (OSTI)

Current designs for electric motors use a housing that acts as both a structural support and as a method of cooling the stator and rotor. This approach to cooling is not as effective as possible because heat must flow from the rotor and stator through the housing to the cooling media. Because the housing must contain the coolant, it is also larger, heavier, and more expensive than necessary. This project develops a motor that uses a direct lamination cooling (DLC) system, passing coolant directly through the stator and eliminating the need for bulky housing, thereby improving heat transfer. Motor size could be reduced by up to 30-40%, mass by up to 20-30%, and cost by up to 30%. Phase I demonstrated that reliable lamination-to-lamination seals and reliable stack-to-manifold seals can be achieved using the methods identified. The addition of the selected sealants adds only slightly to the thermal resistance and pressure drop compared with unsealed counterparts. Phase II builds electric motors and inductors using the DLC method, obtain comparative performance data on the effectiveness of the method, and then obtain operational use data on these components through long term testing in a representative environment. The long-term testing will ensure that real world aspects of motor and inductor operation (including vibration, temperature cycling, and the presence of electrical and magnetic fields) do not degrade the seals such that leaking occurs or that the thermal performance degrades.

Rippel, Wally; Kobayashi, Drayll

2003-07-30T23:59:59.000Z

353

Torque limit of PM motors for field-weakening region operation  

SciTech Connect

The invention includes a motor controller and technique for controlling a permanent magnet motor. In accordance with one aspect of the present technique, a permanent magnet motor is controlled by receiving a torque command, determining a physical torque limit based on a stator frequency, determining a theoretical torque limit based on a maximum available voltage and motor inductance ratio, and limiting the torque command to the smaller of the physical torque limit and the theoretical torque limit. Receiving the torque command may include normalizing the torque command to obtain a normalized torque command, determining the physical torque limit may include determining a normalized physical torque limit, determining a theoretical torque limit may include determining a normalized theoretical torque limit, and limiting the torque command may include limiting the normalized torque command to the smaller of the normalized physical torque limit and the normalized theoretical torque limit.

Royak, Semyon (Beachwood, OH); Harbaugh, Mark M. (Richfield, OH)

2012-02-14T23:59:59.000Z

354

NEW MOTOR DESIGN CONCEPT FOR ENERGY SAVING APPLIED TO  

E-Print Network (OSTI)

SHARK, NEW MOTOR DESIGN CONCEPT FOR ENERGY SAVING APPLIED TO SWITCHED RELUCTANCE MOTOR by Ana of the cylindrical and Shark air gap Switched Reluctance Motors and their assistance during the experimental work with other motor technologies such

355

Disc rotors with permanent magnets for brushless DC motor  

DOE Patents (OSTI)

A brushless dc permanent magnet motor drives an autonomous underwater vehe. In one embodiment, the motor comprises four substantially flat stators in stacked relationship, with pairs of the stators axially spaced, each of the stators comprising a tape-wound stator coil, and first and second substantially flat rotors disposed between the spaced pairs of stators. Each of the rotors includes an annular array of permanent magnets embedded therein. A first shaft is connected to the first rotor and a second, concentric shaft is connected to the second rotor, and a drive unit causes rotation of the two shafts in opposite directions. The second shaft comprises a hollow tube having a central bore in which the first shaft is disposed. Two different sets of bearings support the first and second shafts. In another embodiment, the motor comprises two ironless stators and pairs of rotors mounted on opposite sides of the stators and driven by counterrotating shafts.

Hawsey, Robert A. (Oak Ridge, TN); Bailey, J. Milton (Knoxville, TN)

1992-01-01T23:59:59.000Z

356

MOtor Vehicle Emission Simulator (MOVES) | Open Energy Information  

Open Energy Info (EERE)

MOtor Vehicle Emission Simulator (MOVES) MOtor Vehicle Emission Simulator (MOVES) Jump to: navigation, search Tool Summary Name: MOtor Vehicle Emission Simulator (MOVES) Agency/Company /Organization: U.S. Environmental Protection Agency Focus Area: GHG Inventory Development Topics: Analysis Tools Website: www.epa.gov/otaq/models/moves/index.htm This emission modeling system estimates emissions from mobile sources, including cars, trucks, and motorcycles. The modeling tool covers a broad range of pollutants and allows multiple scale analysis. How to Use This Tool This tool is most helpful when using these strategies: Shift - Change to low-carbon modes Improve - Enhance infrastructure & policies Learn more about the avoid, shift, improve framework for limiting air pollutants and greenhouse gas emissions.

357

Measuring Devices: Compressed Natural Gas Retail Motor ...  

Science Conference Proceedings (OSTI)

Compressed Natural Gas Retail Motor-Fuel Dispensers. ... Hydrogen Measuring Devices; Liquefied Petroleum Gas Liquid-Measuring Devices; ...

2010-10-05T23:59:59.000Z

358

Frequency modulation drive for a piezoelectric motor  

DOE Patents (OSTI)

A piezoelectric motor has peak performance at a specific frequency f.sub.1 that may vary over a range of frequencies. A drive system is disclosed for operating such a motor at peak performance without feedback. The drive system consists of the motor and an ac source connected to power the motor, the ac source repeatedly generating a frequency over a range from f.sub.1 -.DELTA.x to f.sub.1 +.DELTA.y.

Mittas, Anthony (Albuquerque, NM)

2001-01-01T23:59:59.000Z

359

Retail Motor-Fuel Dispensers and Consoles  

Science Conference Proceedings (OSTI)

Retail Motor-Fuel Dispensers and Consoles. Purpose: This 5-day RMFD course provides participants with the knowledge ...

2013-01-11T23:59:59.000Z

360

Honda Smart Home to Include Berkeley Lab Ventilation Controller  

NLE Websites -- All DOE Office Websites (Extended Search)

Honda Smart Home to Include Berkeley Lab Ventilation Controller Honda Smart Home to Include Berkeley Lab Ventilation Controller Honda smart home October 2013 October-November Special Focus: Energy Efficiency, Buildings, and the Electric Grid Honda Motor Company Inc is proceeding with plans to build a Smart Home in Davis, California, to demonstrate the latest in renewable energy technologies and energy efficiency. The home is expected to produce more energy than is consumed, demonstrating how the goal of "zero net energy" can be met in the near term future. A ventilation controller developed by researchers at Berkeley Lab's Environmental Energy Technologies Division (EETD) will be included in the smart home. EETD is currently working with the developers of the home control system to integrate its control algorithms.

Note: This page contains sample records for the topic "includes finished motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Coupling between motor proteins determines dynamic behaviors of motor protein assemblies  

E-Print Network (OSTI)

Coupling between motor proteins determines dynamic behaviors of motor protein assemblies Jonathan W of intracellular cargos by multiple microtubule motor proteins is believed to be a common and significant phenomenon in vivo, yet signatures of the microscopic dynamics of multiple motor systems are only now

362

Ameren Illinois (Electric) - Custom, HVAC, and Motor Business...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Custom, HVAC, and Motor Business Efficiency Incentives Ameren Illinois (Electric) - Custom, HVAC, and Motor Business Efficiency Incentives Eligibility Commercial Industrial...

363

Electric Motor Predictive and Preventive Maintenance Guide  

Science Conference Proceedings (OSTI)

Electric motor failure could result in lost capacity as well as excessive repair and maintenance costs. This guide provides information on establishing an effective maintenance program to help prevent unexpected motor failures, costly downtime, and unnecessary maintenance costs. Specifically, the guide summarizes technical data relative to four basic power plant motor types and associated components.

1992-05-02T23:59:59.000Z

364

Total Cost of Motor-Vehicle Use  

E-Print Network (OSTI)

the use of Persian-Gulf oil by motor vehicles The sociallye r s i a n - G u l f Oil f o r Motor Vehicles 16. T h e C ofor motor vehicles: lost consumer surplus in other oil-

Delucchi, Mark A.

1996-01-01T23:59:59.000Z

365

Magnetic tweezers to study DNA motors  

E-Print Network (OSTI)

Magnetic tweezers to study DNA motors Maria Mañosas Ritort lab UB Barcelona Croquette-Bensimon lab ENS France #12;· Introduction to MT (magnetic tweezers) · Applications: 1. Tracking DNA motors: (i) Helicases (ii) Annealing motor 2. Studying a multiprotein system: DNA replication Outline #12;· Atomic force

Ritort, Felix

366

Thermodynamics and Kinetics of a Brownian Motor  

E-Print Network (OSTI)

Thermodynamics and Kinetics of a Brownian Motor R. Dean Astumian Nonequilibrium fluctuations particle separation and the design of molecular motors and pumps. A small particle in a liquid is subject in conjunction with an- isotropy to drive a motor in the context of a "ratchet and pawl" device shrunk to micro

Linke, Heiner

367

INDUCTION MOTOR FAULT DIAGNOSTIC AND MONITORING METHODS  

E-Print Network (OSTI)

INDUCTION MOTOR FAULT DIAGNOSTIC AND MONITORING METHODS by Aderiano M. da Silva, B.S. A Thesis;i Abstract Induction motors are used worldwide as the "workhorse" in industrial applications material. However, induction motor faults can be detected in an initial stage in order to prevent

Povinelli, Richard J.

368

Motor vehicle fuel analyzer  

DOE Patents (OSTI)

A gas detecting system is described for classifying the type of liquid fuel in a container or tank. The system includes a plurality of semiconductor gas sensors, each of which differs from the other in its response to various organic vapors. The system includes a means of processing the responses of the plurality of sensors such that the responses to any particular organic substance or mixture is sufficiently distinctive to constitute a recognizable ``signature``. The signature of known substances are collected and divided into two classes based on some other known characteristic of the substances. A pattern recognition system classifies the signature of an unknown substance with reference to the two user-defined classes, thereby classifying the unknown substance with regard to the characteristic of interest, such as its suitability for a particular use. 14 figs.

Hoffheins, B.S.; Lauf, R.J.

1997-08-05T23:59:59.000Z

369

Method and apparatus for monitoring motor operated valve motor output torque and power at valve seating  

DOE Patents (OSTI)

A method and apparatus are provided for monitoring a motor operated valve during the brief period when the valve seats and the torque switch trips to deenergize the valve motor. The method uses voltage measurements on the load side of a deenergizing switch that opens to deenergize the motor to determine, among other things, final motor rotational speed and the decelerating torque at motor deenergization.

Casada, Donald A. (Oak Ridge, TN)

1996-01-01T23:59:59.000Z

370

Method and apparatus for monitoring motor operated valve motor output torque and power at valve seating  

DOE Patents (OSTI)

A method and apparatus are provided for monitoring a motor operated valve during the brief period when the valve seats and the torque switch trips to deenergize the valve motor. The method uses voltage measurements on the load side of a deenergizing switch that opens to deenergize the motor to determine, among other things, final motor rotational speed and the decelerating torque at motor deenergization. 14 figs.

Casada, D.A.

1996-01-16T23:59:59.000Z

371

Use of MCC-Based Motor Torque Measurements for Periodic Verification of Motor-Operated Valves  

Science Conference Proceedings (OSTI)

This report develops, justifies, and validates a motor control center- (MCC-) based motor torque periodic verification (MTPV) method for torque-switch-controlled closing strokes of rising stem motor-operated valves (MOVs) with ac motors. The report details the evaluation of motor torque data obtained from electrical measurements at the MCC and covers the use of these (and other) measurements in MOV periodic verification (PV) testing.

2006-03-30T23:59:59.000Z

372

Influence of direct motor-motor interaction in models for cargo transport by a single team of motors  

E-Print Network (OSTI)

We analyze theoretically the effects of excluded-volume interactions between motors on the dynamics of a cargo driven by multiple motors. The model considered shares many commons with other recently proposed in the literature, with the addition of direct interaction between motors and motor back steps. The cargo is assumed to follow a continuum Langevin dynamics, while individual motors evolve following a Monte Carlo algorithm based on experimentally accessible probabilities for discrete forward and backward jumps, and attachment and detachment rates. The links between cargo and motors are considered as non linear springs. By means of numerical simulations we compute the relevant quantities characterizing the dynamical properties of the system, and we compare the results to those for non interacting motors. We find that interactions lead to quite relevant changes in the force-velocity relation for cargo, with a considerable reduction of the stall force, and cause also a notable decrease of the run length. The...

Bouzat, Sebastian; 10.1088/1478-3975/7/4/046009

2010-01-01T23:59:59.000Z

373

System and method for monitoring and controlling stator winding temperature in a de-energized AC motor  

Science Conference Proceedings (OSTI)

A system and method for measuring and controlling stator winding temperature in an AC motor while idling is disclosed. The system includes a circuit having an input connectable to an AC source and an output connectable to an input terminal of a multi-phase AC motor. The circuit further includes a plurality of switching devices to control current flow and terminal voltages in the multi-phase AC motor and a controller connected to the circuit. The controller is configured to activate the plurality of switching devices to create a DC signal in an output of the motor control device corresponding to an input to the multi-phase AC motor, determine or estimate a stator winding resistance of the multi-phase AC motor based on the DC signal, and estimate a stator temperature from the stator winding resistance. Temperature can then be controlled and regulated by DC injection into the stator windings.

Lu, Bin (Kenosha, WI); Luebke, Charles John (Sussex, WI); Habetler, Thomas G. (Snellville, GA); Zhang, Pinjia (Atlanta, GA); Becker, Scott K. (Oak Creek, WI)

2011-12-27T23:59:59.000Z

374

Alfalfa leaf meal in finishing steer diets. Quarterly report, July 1, 1997--September 30, 1997  

DOE Green Energy (OSTI)

Ninety-six medium frame, Angus and Angus cross steer calves (average initial weight 540 lb.) were allotted to a heavy or light weight block and then randomly assigned to one of four dietary treatments for a 167 or 189-day finishing phase, respectively. Treatments were control (supplemental soybean meal), alfalfa leaf meal (ALM) providing 33%, 66%, 100% of supplemental protein. Finishing diets were formulated to contain .61 Mcal NE{sub g}/lb dry matter, 12.5% crude protein, .6 % Ca and .3 % P. There were no significant (P >.05) effects of dietary treatments on daily gain or dry matter required /lb of gain. Steers fed 100 % ALM consumed more (P <.05) dry matter than steers fed either of the other three treatments. Dry matter consumption increased linearly (P >.05) with increasing ALM. There was no significant (P >.05) dietary treatment effect on marbling, KPH %, yield grade, quality grade, or liver abscesses. There was an apparent trend in reduced liver abscess incidence in steers fed 100 % ALM. Steers fed 66 % ALM had significantly (P <.05) greater backfat measurements, backfat also had a cubic effect (P <.05). Hot carcass weight had a quadratic relation (P <.05) with level of ALM. Substituting alfalfa leaf meal for soybean meal in diets of finishing steers increased DM intake, but this increase was accompanied by an increase in gain which resulted in similar feed efficiency. There may be an advantage in blending ALM and soybean meal as feed efficiency was improved when cattle were fed the blend. Also, feeding ALM may result in lower incidence of liver abscess.

Zehnder, C.M.; DiCostanzo, A.; Smith, L.B.; Brown, D.B.; Hall, J.M.

1997-10-30T23:59:59.000Z

375

Method and apparatus for controlling multiple motors  

DOE Patents (OSTI)

A method and apparatus are provided for simultaneously controlling a plurality of stepper motors. Addressing circuitry generates address data for each motor in a periodic address sequence. Memory circuits respond to the address data for each motor by accessing a corresponding memory location containing a first operational data set functionally related to a direction for moving the motor, speed data, and rate of speed change. First logic circuits respond to the first data set to generate a motor step command. Second logic circuits respond to the command from the first logic circuits to generate a third data set for replacing the first data set in memory with a current operational motor status, which becomes the first data set when the motor is next addressed.

Jones, Rollin G. (Los Alamos, NM); Kortegaard, Bert L. (Los Alamos, NM); Jones, David F. (Los Alamos, NM)

1987-01-01T23:59:59.000Z

376

Method and apparatus for controlling multiple motors  

DOE Patents (OSTI)

A method and apparatus are provided for simultaneously controlling a plurality of stepper motors. Addressing circuitry generates address data for each motor in a periodic address sequence. Memory circuits respond to the address data for each motor by accessing a corresponding memory location containing a first operational data set functionally related to a direction for moving the motor, speed data, and rate of speed change. First logic circuits respond to the first data set to generate a motor step command. Second logic circuits respond to the command from the first logic circuits to generate a third data set for replacing the first data set in memory with a current operational motor status, which becomes the first data set when the motor is next addressed.

Jones, R.G.; Kortegaard, B.L.; Jones, D.F.

1986-07-22T23:59:59.000Z

377

Genomics Presentations from DOE JGI's Fourth Annual Sequencing, Finishing, Analysis in the Future Meeting, 2009  

DOE Data Explorer (OSTI)

\tMedicago trunculata Resequencing of 384 lines, Joann Mudge \tPerformance Comparison of Two Genome Partitioning Platforms, Jon Armstrong \tPrescreening Illumina Data Results in High-Quality Genome Polishing, Cliff Han \tGenePRIMP: Improving Microbial Gene Prediction Quality, Amrita Pati \tIMG Systems for Comparative Analysis of Microbial Genomes and Metagenomes, Victor Markowitz \tAutomated Microbial Genome Annotation, Miriam Land \tNew Technology Drafts: Production and Improvements, Alla Lapidus \tHuman Microbiome Finishing, Jessica Hostetler

378

Progressive Powder Coating: New Infrared Curing Oven at Metal Finishing Plant Increases Production by 50%  

SciTech Connect

Progressive Powder Coating in Mentor, Ohio, is a metal finishing plant that uses a convection oven in its manufacturing process. In an effort to save energy and improve production, the company installed an infrared oven in between the powder coating booth and the convection oven on its production line. This installation allowed the plant to increase its conveyor line speed and increase production by 50 percent. In addition, the plant reduced its natural gas consumption, yielding annual energy savings of approximately$54,000. With a total project cost of$136,000, the simple payback is 2.5 years.

Not Available

2003-05-01T23:59:59.000Z

379

MTBE, Oxygenates, and Motor Gasoline  

Gasoline and Diesel Fuel Update (EIA)

MTBE, Oxygenates, and MTBE, Oxygenates, and Motor Gasoline Contents * Introduction * Federal gasoline product quality regulations * What are oxygenates? * Who gets gasoline with oxygenates? * Which areas get MTBE? * How much has been invested in MTBE production capacity? * What does new Ethanol capacity cost? * What would an MTBE ban cost? * On-line information resources * Endnotes * Summary of revisions to this analysis Introduction The blending of methyl tertiary butyl ether (MTBE) into motor gasoline has increased dramatically since it was first produced 20 years ago. MTBE usage grew in the early 1980's in response to octane demand resulting initially from the phaseout of lead from gasoline and later from rising demand for premium gasoline. The oxygenated gasoline program stimulated an

380

Solid Rocket Motor Acoustic Testing  

DOE Green Energy (OSTI)

Acoustic data are often required for the determination of launch and powered flight loads for rocket systems and payloads. Such data are usually acquired during test firings of the solid rocket motors. In the current work, these data were obtained for two tests at a remote test facility where we were visitors. This paper describes the data acquisition and the requirements for working at a remote site, interfacing with the test hosts.

Rogers, J.D.

1999-03-31T23:59:59.000Z

Note: This page contains sample records for the topic "includes finished motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

INSPECTION MEANS FOR INDUCTION MOTORS  

DOE Patents (OSTI)

an appartus is descripbe for inspcting electric motors and more expecially an appartus for detecting falty end rings inn suqirrel cage inductio motors while the motor is running. In its broua aspects, the mer would around ce of reference tedtor means also itons in the phase ition of the An electronic circuit for conversion of excess-3 binary coded serial decimal numbers to straight binary coded serial decimal numbers is reported. The converter of the invention in its basic form generally coded pulse words of a type having an algebraic sign digit followed serially by a plurality of decimal digits in order of decreasing significance preceding a y algebraic sign digit followed serially by a plurality of decimal digits in order of decreasing significance. A switching martix is coupled to said input circuit and is internally connected to produce serial straight binary coded pulse groups indicative of the excess-3 coded input. A stepping circuit is coupled to the switching matrix and to a synchronous counter having a plurality of x decimal digit and plurality of y decimal digit indicator terminals. The stepping circuit steps the counter in synchornism with the serial binary pulse group output from the switching matrix to successively produce pulses at corresponding ones of the x and y decimal digit indicator terminals. The combinations of straight binary coded pulse groups and corresponding decimal digit indicator signals so produced comprise a basic output suitable for application to a variety of output apparatus.

Williams, A.W.

1959-03-10T23:59:59.000Z

382

Coupling of Two Motor Proteins: a New Motor Can Move Faster  

E-Print Network (OSTI)

We study the effect of a coupling between two motor domains in highly-processive motor protein complexes. A simple stochastic discrete model, in which the two parts of the protein molecule interact through some energy potential, is presented. The exact analytical solutions for the dynamic properties of the combined motor species, such as the velocity and dispersion, are derived in terms of the properties of free individual motor domains and the interaction potential. It is shown that the coupling between the motor domains can create a more efficient motor protein that can move faster than individual particles. The results are applied to analyze the motion of helicase RecBCD molecules.

Evgeny B. Stukalin; Hubert Phillips III; Anatoly B. Kolomeisky

2005-02-19T23:59:59.000Z

383

Method for assessing in-service motor efficiency and in-service motor/load efficiency  

DOE Patents (OSTI)

A method and apparatus for assessing the efficiency of an in-service motor. The operating characteristics of the in-service motor are remotely measured. The operating characteristics are then applied to an equivalent circuit for electrical motors. Finally the equivalent circuit is evaluated to determine the performance characteristics of said in-service motor. Based upon the evaluation an individual is able to determine the rotor speed, power output, efficiency, and toque of the in-service motor. Additionally, an individual is able to confirm the calculations by comparing measured values with values obtained as a result of the motor equivalent circuit evaluation.

Kueck, John D. (Oak Ridge, TN); Otaduy, Pedro J. (Oak Ridge, TN)

1997-01-01T23:59:59.000Z

384

Assessment of Efficiency and Application of Advanced Motor Technologies  

Science Conference Proceedings (OSTI)

This technical update explores four major emerging motor technologies. The four advanced motor types are Permanent magnet Brushless DC Motors (BLDC), Permanent Magnet Synchronous Motors (PMSM), Switched Reluctance Motors and Field Oriented Vector Control Motors. These motor technologies are not necessarily new, but are becoming popular and attractive solutions because of material cost reductions, controller innovations or the promise of higher efficiency and improved component reliability. Overall, the a...

2009-12-23T23:59:59.000Z

385

The evaluation of sorghum dried distiller's grains with solubles in nursery pig diets, on finishing pig performance and meat quality, and on lactating sow performance.  

E-Print Network (OSTI)

??Five experiments were conducted to determine the effects of sorghum dried distillers grains with solubles (DDGS) on nursery pig performance, finishing pig performance and meat (more)

Sotak, Kelly Marie

2012-01-01T23:59:59.000Z

386

Control system for a wound-rotor motor  

DOE Patents (OSTI)

A load switching circuit for switching two or more transformer taps under load carrying conditions includes first and second parallel connected bridge rectifier circuits which control the selective connection of a direct current load to taps of a transformer. The first bridge circuit is normally conducting so that the load is connected to a first tap through the first bridge circuit. To transfer the load to the second tap, a switch is operable to connect the second bridge circuit to a second tap, and when the second bridge circuit begins to conduct, the first bridge circuit ceases conduction because the potential at the second tap is higher than the potential at the first tap, and the load is thus connected to the second tap through the second bridge circuit. The load switching circuit is applicable in a motor speed controller for a wound-rotor motor for effecting tap switching as a function of motor speed while providing a stepless motor speed control characteristics.

Ellis, J.N.

1981-07-17T23:59:59.000Z

387

Control system for a wound-rotor motor  

DOE Patents (OSTI)

A load switching circuit for switching two or more transformer taps under load carrying conditions includes first and second parallel connected bridge rectifier circuits which control the selective connection of a direct current load to taps of a transformer. The first bridge circuit is normally conducting so that the load is connected to a first tap through the first bridge circuit. To transfer the load to the second tap, a switch is operable to connect the second bridge circuit to a second tap, and when the second bridge circuit begins to conduct, the first bridge circuit ceases conduction because the potential at the second tap is higher than the potential at the first tap, and the load is thus connected to the second tap through the second bridge circuit. The load switching circuit is applicable in a motor speed controller for a wound-rotor motor for effecting tap switching as a function of motor speed while providing a stepless motor speed control characteristic.

Ellis, James N. (Chatsworth, CA)

1983-01-01T23:59:59.000Z

388

CONTAMINATED PROCESS EQUIPMENT REMOVAL FOR THE D&D OF THE 232-Z CONTAMINATED WASTE RECOVERY PROCESS FACILITY AT THE PLUTONIUM FINISHING PLANT (PFP)  

SciTech Connect

This paper describes the unique challenges encountered and subsequent resolutions to accomplish the deactivation and decontamination of a plutonium ash contaminated building. The 232-Z Contaminated Waste Recovery Process Facility at the Plutonium Finishing Plant was used to recover plutonium from process wastes such as rags, gloves, containers and other items by incinerating the items and dissolving the resulting ash. The incineration process resulted in a light-weight plutonium ash residue that was highly mobile in air. This light-weight ash coated the incinerator's process equipment, which included gloveboxes, blowers, filters, furnaces, ducts, and filter boxes. Significant airborne contamination (over 1 million derived air concentration hours [DAC]) was found in the scrubber cell of the facility. Over 1300 grams of plutonium held up in the process equipment and attached to the walls had to be removed, packaged and disposed. This ash had to be removed before demolition of the building could take place.

HOPKINS, A.M.; MINETTE, M.J.; KLOS, D.B.

2007-01-25T23:59:59.000Z

389

Electric Motor Drive Selection Issues for HEV Propulsion Systems: A Comparative Study  

E-Print Network (OSTI)

, the induction motor, the permanent magnet synchronous motor, and the switched reluctance motor. The main motor, the permanent magnet synchronous motor, and the switched reluctance motor [2]. Cross induction motors and the permanent magnet motors are highly dominant, whereas those on dc motors

Paris-Sud XI, Université de

390

Improved motors for utility applications. Volume 2. Industry assessment study. Final report  

SciTech Connect

Auxiliary drive motor failures in electric utility applications result in large repair costs and, energy replacement costs. In order to assess the motor reliability experience of the utility industry and identify specific problem areas, information or more than 4800 motors at 132 generating units owned by 56 utilities was collected. The computerized database encompasses all fuel sources, geographic factors and motor manufacturers. Analysis of the data, field interviews with utilities across the country and technical judgment were used to identify the major factors influencing motor reliability. In total, 1221 failures were reported which represents a rate of 4.6% failure per motor per year. Several utilities reported experience as good as 1 or 2% and others as poor as 12%. Although all manufacturers can supply reliable equipment for most applications, failures of specific components in certain specific applications appear to be associated with specific manufacturers. However, overall, 22% of all reported failures were attributed to winding failure and 13% to sleeve bearings. Numerous examples of misapplication were discovered such as the horizontal motor which was vertically mounted by an OEM, inadequately balanced hydraulic thrust loads in a packaged motor/pump system and inappropriate enclosure specified for a motor located outdoors.The internal procedures and practices of those utilities which had particularly low failure rate experience included such factors as, stringent specifications, objective purchasing policies, adequate record keeping and preventative maintenance programs. Auxiliary large drive motor failures are estimated to cost the average utility over $350,000 per unit per year for alternate energy source during outages. Future cooperative efforts by the manufacturers, the A and E firms, the OEM's and the utilities could significantly reduce this value.

Mighdoll, P.; Bloss, R.P.; Hayashi, F.

1982-10-01T23:59:59.000Z

391

Electric Motor Efficiency Standards and Regulations  

Science Conference Proceedings (OSTI)

The last few years have seen the introduction of new standards and regulations for electric motor efficiency in the United States and elsewhere. The Energy Independence and Security Act (EISA) of 2007 is perhaps the most significant of these and is expected to have a considerable impact on electric motor efficiency in the United States. Based on the National Equipment Manufacturers Association (NEMA) MG 1 2010 Premium Efficiency standard, EISA 2007 mandates that all new induction motors (barring some exc...

2011-07-31T23:59:59.000Z

392

Motor current signature analysis method for diagnosing motor-operated devices  

DOE Patents (OSTI)

A motor current noise signature analysis method for remotely monitoring the operating characteristics of an electric motor-operated device such as a motor-operated valve. Frequency domain signal analysis techniques are applied to a conditioned motor current signal to distinctly identify various operating parameters of the motor driven device from the motor current signature. The signature may be recorded and compared with subsequent signatures to detect operating abnormalities and degradation of the device. This diagnostic method does not require special equipment to be installed on the motor-operated device, and the current sensing may be performed at remote control locations, e.g., where the motor-operated devices are used in inaccessible or hostile environments. 6 figs.

Haynes, H.D.; Eissenberg, D.M.

1986-09-30T23:59:59.000Z

393

DOE Energy Information Administration Motor Gasoline Watch  

U.S. Energy Information Administration (EIA)

Motor Gasoline Watch November 18, 1998. SUPPLY. Higher production levels and a decline in demand contributed to an increase in stocks last week.

394

Total Economics of Energy Efficient Motors  

E-Print Network (OSTI)

Due to the large increases in cost of electrical energy in recent years, the energy savings attainable with the use of energy-efficient motors is very attractive to all motor users. But energy and electric demand charge savings tell only part of the story. Engineers responsible for the selection of motors for many varying uses must also consider many less tangible factors when deciding whether a price premium for an energy-efficient motor is justified. These important intangible factors may throw a borderline decision in favor of a premium motor; at other times these factors may dictate that the capital money could be spent more wisely in other areas. This paper will point out those factors which effect the decision of whether or not to buy a premium priced energy-efficient motor or a standard electric motor. It will also address the question of whether it is cost-effective to rewind an old motor which has failed or to replace it with a new energy-efficient motor.

Nester, A. T.

1984-01-01T23:59:59.000Z

395

Measuring Devices: Retail Motor-Fuel Dispensers  

Science Conference Proceedings (OSTI)

Retail Motor-Fuel Dispensers - Single, Dual, and Multi-Product and Blended Product. Intro about it. EPOs, Field Manual, Training ...

2010-10-05T23:59:59.000Z

396

Tesla Motors Inc | Open Energy Information  

Open Energy Info (EERE)

Carlos, California Zip 94070 Sector Vehicles Product California-based producer of luxury electric vehicles, such as sports cars. References Tesla Motors Inc1 LinkedIn...

397

Food Industry - Motor Contactors Burning Up  

Science Conference Proceedings (OSTI)

This power quality (PQ) case study presents the investigation of motor contactors that have burnt up several times in the last year at a food manufacturing facility.

2003-12-31T23:59:59.000Z

398

Synchronous operation of the BLDC motor  

E-Print Network (OSTI)

The brushless de (BLDC) motor is becoming widely used and popular in the small horsepower motor applications. Factors such as simplicity in control, low cost, high efficiency, low frame size, high torque per inertia, high power density and, most importantly, being br-ushless are the reasons that make the BLDC motor very attractive in motor drive applications. In this research a systematic approach to synchronous operation of the brushless DC (BLDC) motor has been investigated and implemented. This thesis establishes principles of synchronous operation of the BLDC motor, develops stable operating conditions, derives the required implementation formulas and introduces some new definitions. The synchronous system follows, open loop, a speed command. The system has been provided by two input references: current and speed. The current reference throughout the operation has been kept constant at the maximum applicable continuous current to obtain maximum torque. Current regulation has been achieved by hysteresis current control. The speed reference has been varied from zero speed to the desired speed linearly. Once speed reaches to the desired speed, it is kept constant at the desired speed. Since the motor operates synchronously and no position information has been used, the motor has to follow exactly the reference speed, otherwise pull out occurs. By this implementation, three operating points of the BLDC motor with synchronous operational system has been presented. One of the three operating points at maximum speed corresponds to maximum load operation.

Guzelgunler, Yilcan

1998-01-01T23:59:59.000Z

399

The LatestThe LatestThe LatestThe Latest,,,, Quick Motor EvaluationQuick Motor EvaluationQuick Motor EvaluationQuick Motor Evaluation Myway Plus Development of Specialized Equipment  

E-Print Network (OSTI)

The LatestThe LatestThe LatestThe Latest,,,, Quick Motor EvaluationQuick Motor EvaluationQuick Motor EvaluationQuick Motor Evaluation Myway Plus Development of Specialized Equipment Myway Plus developed a quick test/evaluation equipment for highly efficient hybrid car (HV) motor. The equipment

Kambhampati, Patanjali

400

Electric Motor Remanufacturing and Energy Savings Sahil Sahni1  

E-Print Network (OSTI)

Electric Motor Remanufacturing and Energy Savings Sahil Sahni1 , Avid Boustani1 , Timothy Gutowski to this study. #12;Contents 1 Introduction to Electric Motors 1 1.1 Motor Classifications . . . . . . . . . . . . . . . . . . . . . . . 1 1.2 Performance of Motors . . . . . . . . . . . . . . . . . . . . . . 4 1.3 Impact of motor

Gutowski, Timothy

Note: This page contains sample records for the topic "includes finished motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Motor Energy Saving Opportunities in an Industrial Plant  

E-Print Network (OSTI)

Industrial plants have enormous energy saving opportunities with electric motors. Improving motor efficiency is a conventional wisdom to save energy. Re-engineering affords far greater savings opportunities than motor efficiency improvement. Motor energy saving techniques and basics are discussed. A case study is presented where 63% motor energy savings were realized.

Kumar, B.; Elwell, A.

1999-05-01T23:59:59.000Z

402

System and method for motor fault detection using stator current noise cancellation  

Science Conference Proceedings (OSTI)

A system and method for detecting incipient mechanical motor faults by way of current noise cancellation is disclosed. The system includes a controller configured to detect indicia of incipient mechanical motor faults. The controller further includes a processor programmed to receive a baseline set of current data from an operating motor and define a noise component in the baseline set of current data. The processor is also programmed to acquire at least on additional set of real-time operating current data from the motor during operation, redefine the noise component present in each additional set of real-time operating current data, and remove the noise component from the operating current data in real-time to isolate any fault components present in the operating current data. The processor is then programmed to generate a fault index for the operating current data based on any isolated fault components.

Zhou, Wei (Los Angeles, CA); Lu, Bin (Kenosha, WI); Nowak, Michael P. (Menomonee Falls, WI); Dimino, Steven A. (Wauwatosa, WI)

2010-12-07T23:59:59.000Z

403

Use of Downhole Motors in Geothermal Drilling in the Philippines  

SciTech Connect

This paper describes the use of downhole motors in the Tiwi geothermal field in the Philippines, The discussion includes the application Of a Dyna-Drill with insert-type bits for drilling through surface alluvium. The economics of this type of drilling are compared to those of conventional rotary drilling. The paper also describes the use of a turbodrill that drills out scale as the well produces geothermal fluids.

Pyle, D. E.

1981-01-01T23:59:59.000Z

404

Catalyst for converting synthesis gas to liquid motor fuels  

DOE Patents (OSTI)

The addition of an inert metal component, such as gold, silver or copper, to a Fischer-Tropsch catalyst comprising cobalt enables said catalyst to convert synthesis gas to liquid motor fuels at about 240.degree.-370.degree. C. with advantageously reduced selectivity of said cobalt for methane in said conversion. The catalyst composition can advantageously include a support component, such as a molecular sieve, co-catalyst/support component or a combination of such support components.

Coughlin, Peter K. (Yorktown Heights, NY)

1986-01-01T23:59:59.000Z

405

Guide for the Specification of Replacement and Spare AC Squirrel-Cage Induction Motors Having Voltage Ratings Up to 600 V  

Science Conference Proceedings (OSTI)

This report was developed by the Electric Power Research Institute (EPRI) Large Electric Motor Users Group (LEMUG) Applications Working Group (AWG), which included motor engineers, consultants, and vendors. This report and the specification it contains provide a solid framework for procuring new or replacement low-voltage (up to 600 Vac) National Electrical Manufacturers Association (NEMA) T-frame squirrel-cage induction motors. This report draws from other industry sources, including NEMA MG-1 and ...

2013-05-31T23:59:59.000Z

406

Radioactive air emissions notice of construction for vertical calciner operation at the plutonium finishing plant  

SciTech Connect

This document serves as a notice of construction (NOC) for construction, installation, and operation of a vertical calciner to stabilize plutonium at the Plutonium Finishing Plant (PFP)Complex, pursuant to the requirements of Washington Administrative Code (WAC) 246-247-060. The PFP Complex activities are focused on the cleanout and stabilization of plutonium residue left from plutonium weapons material processing activities. The prime purpose of the vertical calciner is to convert plutonium acid solutions to a more stable plutonium oxide. A test calciner has been developed and put in place in the 234-5Z Building. Development testing of this vertical calciner is ongoing. A new vertical calciner will be assembled for actual stabilization operation in Room 230C of the 234-5Z Building. The test calciner may be upgraded or replaced as an alternative to building a new calciner in Room 230C.

Hays, C.B., Westinghouse Hanford

1996-07-17T23:59:59.000Z

407

PLUTONIUM FINISHING PLANT (PFP) SUB-GRADE EE/CA EVALUATION OF ALTERNATIVES A NEW MODEL  

SciTech Connect

An engineering evaluation/cost analysis (EE/CA) was performed at the Hanford Site's Plutonium Finishing Plant (PFP). The purpose of the EVCA was to identify the sub-grade items to be evaluated; determine the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) hazardous substances through process history and available data; evaluate these hazards; and as necessary, identify the available alternatives to reduce the risk associated with the contaminants. The sub-grade EWCA considered four alternatives for an interim removal action: (1) No Action; (2) Surveillance and Maintenance (S&M); (3) Stabilize and Leave in Place (Stabilization); and (4) Remove, Treat and Dispose (RTD). Each alternative was evaluated against the CERCLA criteria for effectiveness, implementability, and cost.

HOPKINS, A.M.

2007-06-08T23:59:59.000Z

408

The Chemical Hazards Assessments Prior to D&D of the Plutonium Finishing Plant Hanford Nuclear Reservation  

Science Conference Proceedings (OSTI)

All Hanford facilities, including the Plutonium Finishing Plant (PFP) were evaluated for chemical hazards in 1997, 1998 and 2000. The hazard evaluation, known as the PFP Facility Vulnerability Assessment (FVA), was prompted when chemicals in Tank A-109 in the Plutonium Reclamation Facility (PRF) exploded in May 1997. Actions were undertaken to eliminate or reduce what were thought to be the worst hazards following that evaluation. In 2001, a new PFP team was organized to review the progress to date in reducing hazards and to reassess hazards that might still remain within the facility. This reassessment continued into 2002 and is referred to as the 2002 PFP Residual Chemical Hazards Reassessment (RCHR). This report explains the results of the 2001/2002 reassessment of the chemical hazards at PFP. This reassessment effort forms the basis of the RCHR. The RCHR relied on previous assessments as the starting point for the 2001/2002 evaluation and used ranking criteria very similar to previous efforts. The RCHR team was composed of professionals representing Industrial Hygiene, Chemical Engineering, Mechanical Engineering, Hazardous Materials Handling Specialists, Solid Waste Management Specialists and Environmental Specialists. All areas of concern that could be accessed were physically examined and photographed where possible. Information from processing records, facility drawings and documents, design engineers, process engineers and work packages were compiled. The PFP vessel inventory was examined and expanded where required. New items listed in the vessel inventory were investigated. All items investigated were ranked using the hazard ranking criteria developed. This information was put on data sheets and compiled in a database.

FITCH, L.R.; HOPKINS, A.M.

2003-01-01T23:59:59.000Z

409

Abstract--There are two types of drivers in production machine systems: constant velocity (CV) motor and servo-motor.  

E-Print Network (OSTI)

) motor and servo-motor. If a system contains two drivers or more, among which some are of the CV motor while the other are the servo-motor, the system has the so-called hybrid driver architecture is stable. A simulation is performed to show verify the proposed controller. The CV motor has the velocity

Zhang, WJ "Chris"

410

Motor Pool Guidelines for Geosciences A completed Motor Pool Request form must be submitted to Denise for  

E-Print Network (OSTI)

Motor Pool Guidelines for Geosciences · A completed Motor Pool Request form must be submitted on the Geosciences website under the forms link. http://www.geo.arizona.edu/pdf/motor_pool_request.pdf · If the trip be submitted with the Motor Pool Request. · A list of passengers and drivers is for all motor pool travel (this

Holliday, Vance T.

411

ASSESSING CHEMICAL HAZARDS AT THE PLUTONIUM FINISHING PLANT (PFP) FOR PLANNING FUTURE D&D  

Science Conference Proceedings (OSTI)

This paper documents the fiscal year (FY) 2006 assessment to evaluate potential chemical and radiological hazards associated with vessels and piping in the former plutonium process areas at Hanford's Plutonium Finishing Plant (PFP). Evaluations by PFP engineers as design authorities for specific systems and other subject-matter experts were conducted to identify the chemical hazards associated with transitioning the process areas for the long-term layup of PFP before its eventual final decontamination and decommissioning (D and D). D and D activities in the main process facilities were suspended in September 2005 for a period of between 5 and 10 years. A previous assessment conducted in FY 2003 found that certain activities to mitigate chemical hazards could be deferred safely until the D and D of PFP, which had been scheduled to result in a slab-on-grade condition by 2009. As a result of necessary planning changes, however, D and D activities at PFP will be delayed until after the 2009 time frame. Given the extended project and plant life, it was determined that a review of the plant chemical hazards should be conducted. This review to determine the extended life impact of chemicals is called the ''Plutonium Finishing Plant Chemical Hazards Assessment, FY 2006''. This FY 2006 assessment addresses potential chemical and radiological hazard areas identified by facility personnel and subject-matter experts who reevaluated all the chemical systems (items) from the FY 2003 assessment. This paper provides the results of the FY 2006 chemical hazards assessment and describes the methodology used to assign a hazard ranking to the items reviewed.

HOPKINS, A.M.; KLOS, D.B.; MINETT, M.J.

2007-01-25T23:59:59.000Z

412

Fluctuating-friction molecular motors  

E-Print Network (OSTI)

Abstract. We show that the correlated stochastic fluctuation of the friction coefficient can give rise to long-range directional motion of a particle undergoing Brownian random walk in a constant periodic energy potential landscape. The occurrence of this motion requires the presence of two additional independent bodies interacting with the particle via friction and via the energy potential, respectively, which can move relative to each other. Such three-body system generalizes the classical Brownian ratchet mechanism, which requires only two interacting bodies. In particular, we describe a simple two-level model of fluctuating-friction molecular motor that can be solved analytically. In our previous work [M.K., L.M and D.P. 2000 J. Nonlinear Opt. Phys. Mater. 9 157] this model has been first applied to understanding the fundamental mechanism of the photoinduced reorientation of dye-doped liquid crystals. Applications of the same idea to other fields such as molecular biology and nanotechnology can however be envisioned. As an example, in this paper we work out a model of the actomyosin system based on the fluctuating-friction mechanism. PACS numbers: 05.40.+j, 42.70.Df, 87.10.+eFluctuating-friction molecular motors 2 1.

unknown authors

2001-01-01T23:59:59.000Z

413

Influence of direct motor-motor interaction in models for cargo transport by a single team of motors  

E-Print Network (OSTI)

We analyze theoretically the effects of excluded-volume interactions between motors on the dynamics of a cargo driven by multiple motors. The model considered shares many commons with other recently proposed in the literature, with the addition of direct interaction between motors and motor back steps. The cargo is assumed to follow a continuum Langevin dynamics, while individual motors evolve following a Monte Carlo algorithm based on experimentally accessible probabilities for discrete forward and backward jumps, and attachment and detachment rates. The links between cargo and motors are considered as non linear springs. By means of numerical simulations we compute the relevant quantities characterizing the dynamical properties of the system, and we compare the results to those for non interacting motors. We find that interactions lead to quite relevant changes in the force-velocity relation for cargo, with a considerable reduction of the stall force, and cause also a notable decrease of the run length. These effects are mainly due to traffic-like phenomena in the microtubule. The consideration of several parallel tracks for motors reduces such effects. However, we find that for realistic values of the number of motors and the number of tracks, the influence of interactions on the global parameters of transport of cargo are far from being negligible. Our studies provide also an analysis of the relevance of motor back steps on the modeling, and of the influence of different assumptions for the detachment rates. In particular, we discuss these two aspects in connection with the possibility of observing processive back motion of cargo at large load forces.

Sebastian Bouzat; Fernando Falo

2010-12-14T23:59:59.000Z

414

Pulp and Paper Mills: Profiting for Efficient Motor System Use...  

NLE Websites -- All DOE Office Websites (Extended Search)

Motor System Use This profile discusses how energy efficienct motor systems can help pulp and paper mills save money. Pulp and Paper Mills: Profiting for Efficient Motor System Use...

415

Motor Neurons Controlling Fluid Ingestion in Drosophila melanogaster  

E-Print Network (OSTI)

coordination of rhythmic motor patterns. J Neurophysiol 90:Figure 3.5. Individual motor neurons project to eitherGraphs as in (C-D) for MN12 motor neurons. n=10-13 flies per

Manzo, Andrea

2011-01-01T23:59:59.000Z

416

Gas Mileage of 1986 Vehicles by Vixen Motor Company  

NLE Websites -- All DOE Office Websites (Extended Search)

Vixen Motor Company Vehicles EPA MPG MODEL City Comb Hwy 1986 Vixen Motor Company 21 TD 6 cyl, 2.4 L, Manual 5-spd, Diesel Compare 1986 Vixen Motor Company 21 TD 15 City 16...

417

Gas Mileage of 1984 Vehicles by Avanti Motor Corporation  

NLE Websites -- All DOE Office Websites (Extended Search)

84 Avanti Motor Corporation Vehicles EPA MPG MODEL City Comb Hwy 1984 Avanti Motor Corporation Avanti II 8 cyl, 5.0 L, Automatic 4-spd, Regular Gasoline Compare 1984 Avanti Motor...

418

Stocks of Total Crude Oil and Petroleum Products (Including SPR)  

U.S. Energy Information Administration (EIA)

Weekly data for RBOB with Ether, RBOB with Alcohol, and Reformulated GTAB Motor Gasoline Blending Components are discontinued as of the week ending June 4, ...

419

Thermal Stability Studies of Candidate Decontamination Agents for Hanfords Plutonium Finishing Plant Plutonium-Contaminated Gloveboxes  

SciTech Connect

This report provides the results of PNNL's and Fluor's studies of the thermal stabilities of potential wastes arising from decontamination of Hanford's Plutonium Finishing Plant's plutonium contaminated gloveboxes. The candidate wastes arising from the decontamination technologies ceric nitrate/nitric acid, RadPro, Glygel, and Aspigel.

Scheele, Randall D.; Cooper, Thurman D.; Jones, Susan A.; Ewalt, John R.; Compton, James A.; Trent, Donald S.; Edwards, Matthew K.; Kozelisky, Anne E.; Scott, Paul A.; Minette, Michael J.

2005-09-29T23:59:59.000Z

420

A genetic algorithm-based method for look-ahead scheduling in the finishing phase of construction projects  

Science Conference Proceedings (OSTI)

Genetic algorithms (GAs) are widely used in finding solutions for resource constrained multi-project scheduling problems (RCMPSP) in construction projects. In the finishing phase of a complex construction project, each room forms a confined space for ... Keywords: Genetic algorithm (GA), Look-ahead schedule (LAS), RCMPSP, RCPSP, Simulation

Ning Dong; Dongdong Ge; Martin Fischer; Zuhair Haddad

2012-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "includes finished motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Exterior Insulation Finish System (EIFS) Walls ORNL provides the tools to enable industry to engineer durable, moisture-tolerant  

E-Print Network (OSTI)

the insulating value of walls and the energy efficiency of buildings. The EIFS concept came to America fromExterior Insulation Finish System (EIFS) Walls ORNL provides the tools to enable industry for building materials. EIFS's are among the most cost-effective building technologies for improving

Oak Ridge National Laboratory

422

Oscillation control system for electric motor drive  

DOE Patents (OSTI)

A feedback system for controlling mechanical oscillations in the torsionally complaint drive train of an electric or other vehicle. Motor speed is converted in a processor to estimate state signals in which a plant model which are used to electronically modify the torque commands applied to the motor. 5 figs.

Slicker, J.M.; Sereshteh, A.

1988-08-30T23:59:59.000Z

423

Oscillation control system for electric motor drive  

DOE Patents (OSTI)

A feedback system for controlling mechanical oscillations in the torsionally complaint drive train of an electric or other vehicle. Motor speed is converted in a processor to estimate state signals in which a plant model which are used to electronically modify thetorque commands applied to the motor.

Slicker, James M. (Union Lake, MI); Sereshteh, Ahmad (Union Lake, MI)

1988-01-01T23:59:59.000Z

424

Designing Alternatives to State Motor Fuel Taxes  

E-Print Network (OSTI)

Designing Alternatives to State Motor Fuel Taxes All states rely on gasoline taxes as one source are financed from a wide variety of sources, all states use motor fuel taxes as an important source of funds of funds for road improvement and mainte- nance. Historically, gasoline usage has been roughly proportional

Bertini, Robert L.

425

Improve Motor System Efficiency with MotorMaster+, Software Tools for Industry, Industrial Technologies Program (ITP) (Fact Sheet)  

SciTech Connect

This fact sheet describes how the Industrial Technologies Program MotorMaster+ software tool aids industrial plants with finding energy-efficient motor replacement options and managing motor systems.

Not Available

2008-12-01T23:59:59.000Z

426

Acura Acura Alfa Romeo Alfa Romeo American Motors Corporation...  

NLE Websites -- All DOE Office Websites (Extended Search)

Alfa Romeo Alfa Romeo American Motors Corporation American Motors Corporation Aston Martin Aston Martin Audi Audi Bertone Bertone BMW BMW Buick Buick Cadillac Cadillac Chevrolet...

427

Motor System Energy Efficiency Supply Curves: A Methodology for...  

NLE Websites -- All DOE Office Websites (Extended Search)

Motor System Energy Efficiency Supply Curves: A Methodology for Assessing the Energy Efficiency Potential of Industrial Motor Systems Speaker(s): Ali Hasanbeigi Date: February 8,...

428

Improve Motor Operation at Off-Design Voltages  

Science Conference Proceedings (OSTI)

This is one in a series of tip sheets to help manufacturers optimize their industrial motor and motor-driven systems.

Not Available

2008-07-01T23:59:59.000Z

429

Motor monitoring method and apparatus using high frequency current components  

DOE Patents (OSTI)

A motor current analysis method and apparatus for monitoring electrical-motor-driven devices. The method and apparatus utilize high frequency portions of the motor current spectra to evaluate the condition of the electric motor and the device driven by the electric motor. The motor current signal produced as a result of an electric motor is monitored and the low frequency components of the signal are removed by a high-pass filter. The signal is then analyzed to determine the condition of the electrical motor and the driven device.

Casada, Donald A. (Knoxville, TN)

1996-01-01T23:59:59.000Z

430

Ameren Illinois (Electric) - Custom, HVAC, and Motor Business...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Ameren Illinois (Electric) - Custom, HVAC, and Motor Business Efficiency Incentives Ameren Illinois (Electric) - Custom, HVAC, and Motor Business Efficiency Incentives < Back...

431

Vision Industries dba Vision Motor Corp | Open Energy Information  

Open Energy Info (EERE)

Vision Motor Corp) Place Santa Monica, California Zip 90405 Product Santa Monica-based electric vehicle manufacturer. References Vision Industries (dba Vision Motor Corp)1...

432

BPM Motors in Residential Gas Furnaces: What are the Savings?  

E-Print Network (OSTI)

Brushless Permanent Magnet (BPM) motor. Blowers account forIn a BPM motor the rotor contains permanent magnets. Themotors: Permanent Split Capacitor (PSC) and Brushless Permanent Magnet (

Lutz, James; Franco, Victor; Lekov, Alex; Wong-Parodi, Gabrielle

2006-01-01T23:59:59.000Z

433

Motor monitoring method and apparatus using high frequency current components  

DOE Patents (OSTI)

A motor current analysis method and apparatus for monitoring electrical-motor-driven devices are disclosed. The method and apparatus utilize high frequency portions of the motor current spectra to evaluate the condition of the electric motor and the device driven by the electric motor. The motor current signal produced as a result of an electric motor is monitored and the low frequency components of the signal are removed by a high-pass filter. The signal is then analyzed to determine the condition of the electrical motor and the driven device. 16 figs.

Casada, D.A.

1996-05-21T23:59:59.000Z

434

Desenvolvimento experimental de um motor stirling tipo gama.  

E-Print Network (OSTI)

??O presente trabalho consiste no desenvolvimento experimental de um motor Stirling tipo gama. So apresentadas inicialmente as diferentes configuraes deste tipo de motor (alfa, gama (more)

Vinicius Guimares da Cruz

2012-01-01T23:59:59.000Z

435

DOE - Office of Legacy Management -- General Motors Co - Flint...  

Office of Legacy Management (LM)

Motors Co - Flint - MI 07 FUSRAP Considered Sites Site: GENERAL MOTORS CO. (MI.07 ) Eliminated from further consideration under FUSRAP Designated Name: Not Designated Alternate...

436

When Should Inverter-Duty Motors Be Specified?  

SciTech Connect

This is one in a series of tip sheets to help manufacturers optimize their industrial motor and motor-driven systems.

Not Available

2008-07-01T23:59:59.000Z

437

Minimize Adverse Motor and Adjustable Speed Drive Interactions  

SciTech Connect

This is one in a series of tip sheets to help manufacturers optimize their industrial motor and motor-driven systems.

Not Available

2008-07-01T23:59:59.000Z

438

Improving Motor and Drive System Performance: A Sourcebook for Industry  

SciTech Connect

This is one in a series of sourcebooks to assist industrial personnel in understanding and optimizing motors and motor-driven systems

Not Available

2008-09-01T23:59:59.000Z

439

FreedomCAR Advanced Traction Drive Motor Development Phase I  

DOE Green Energy (OSTI)

The overall objective of this program is to design and develop an advanced traction motor that will meet the FreedomCAR and Vehicle Technologies (FCVT) 2010 goals and the traction motor technical targets. The motor specifications are given in Section 1.3. Other goals of the program include providing a cost study to ensure the motor can be developed within the cost targets needed for the automotive industry. The program has focused on using materials that are both high performance and low costs such that the performance can be met and cost targets are achieved. In addition, the motor technologies and machine design features must be compatible with high volume manufacturing and able to provide high reliability, efficiency, and ruggedness while simultaneously reducing weight and volume. Weight and volume reduction will become a major factor in reducing cost, material cost being the most significant part of manufacturing cost at high volume. Many motor technology categories have been considered in the past and present for traction drive applications, including: brushed direct current (DC), PM (PM) brushless dc (BLDC), alternating current (AC) induction, switched reluctance and synchronous reluctance machines. Of these machine technologies, PM BLDC has consistently demonstrated an advantage in terms of power density and efficiency. As rare earth magnet cost has declined, total cost may also be reduced over the other technologies. Of the many different configurations of PM BLDC machines, those which incorporate power production utilizing both magnetic torque as well as reluctance torque appear to have the most promise for traction applications. There are many different PM BLDC machine configurations which employ both of these torque producing mechanisms; however, most would fall into one of two categories--some use weaker magnets and rely more heavily on reluctance torque (reluctance-dominant PM machines), others use strong PMs and supplement with reluctance torque (magnet-dominant PM machines). This report covers a trade study that was conducted in this phase I program to explore which type of machine best suits the FCVT requirements.

Ley, Josh (UQM Technologies, Inc.); Lutz, Jon (UQM Technologies, Inc.)

2006-09-01T23:59:59.000Z

440

Motorized Positioning Apparatus Having Coaxial Carrousels.  

DOE Patents (OSTI)

An automated electrophoretic system is disclosed. The system employs a capillary cartridge having a plurality of capillary tubes. The cartridge has a first array of capillary ends projecting from one side of a plate. The first array of capillary ends are spaced apart in substantially the same manner as the wells of a microtitre tray of standard size. This allows one to simultaneously perform capillary electrophoresis on samples present in each of the wells of the tray. The system includes a stacked, dual carrousel arrangement to eliminate cross-contamination resulting from reuse of the same buffer tray on consecutive executions from electrophoresis. The system also has a gel delivery module containing a gel syringe/a stepper motor or a high pressure chamber with a pump to quickly and uniformly deliver gel through the capillary tubes. The system further includes a multi-wavelength beam generator to generate a laser beam which produces a beam with a wide range of wavelengths. An off-line capillary reconditioner thoroughly cleans a capillary cartridge to enable simultaneous execution of electrophoresis with another capillary cartridge. The streamlined nature of the off-line capillary reconditioner offers the advantage of increased system throughput with a minimal increase in system cost.

Li, Qingbo (State College, PA); Kane, Thomas E. (State College, PA); Liu, Changsheng (State College, PA); Sonnenschein, Bernard (Brooklyn, NY); Sharer, Michael V. (Tyrone, PA); Kernan, John R. (Loganton, PA)

2002-04-02T23:59:59.000Z

Note: This page contains sample records for the topic "includes finished motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Combined passive bearing element/generator motor  

DOE Patents (OSTI)

An electric machine includes a cylindrical rotor made up of an array of permanent magnets that provide a N-pole magnetic field of even order (where N=4, 6, 8, etc.). This array of permanent magnets has bars of identical permanent magnets made of dipole elements where the bars are assembled in a circle. A stator inserted down the axis of the dipole field is made of two sets of windings that are electrically orthogonal to each other, where one set of windings provides stabilization of the stator and the other set of windings couples to the array of permanent magnets and acts as the windings of a generator/motor. The rotor and the stator are horizontally disposed, and the rotor is on the outside of said stator. The electric machine may also include two rings of ferromagnetic material. One of these rings would be located at each end of the rotor. Two levitator pole assemblies are attached to a support member that is external to the electric machine. These levitator pole assemblies interact attractively with the rings of ferromagnetic material to produce a levitating force upon the rotor.

Post, Richard F. (Walnut Creek, CA)

2000-01-01T23:59:59.000Z

442

Honda motor company's CVCC engine  

DOE Green Energy (OSTI)

Honda Motor Company of Japan in a four-year period from 1968 to 1872 designed, tested, and mass-produced a stratified charge engine, the CVCC, which in comparison to conventional engines of similar output at the time was lower in CO, HC and NO/sub x/ emissions and higher in fuel economy. Honda developed the CVCC engine without government assistance or outside help. Honda's success came at a time when steadily increasing fuel costs and the various provisions of the Clean Air Act had forced US automakers to consider possible alternatives to the conventional gasoline engine. While most major engine manufacturers had investigated some form of stratified charge engine, Honda's CVCC was the only one to find successful market application. This case study examines the circumstances surrounding the development of the CVCC engine and its introduction into the Japanese and American markets.

Abernathy, W.J.; Ronan, L.

1980-07-01T23:59:59.000Z

443

Science Accelerator content now includes multimedia  

Office of Scientific and Technical Information (OSTI)

Science Accelerator content now includes multimedia Science Accelerator has expanded its suite of collections to include ScienceCinema, which contains videos produced by the U.S....

444

Multilevel DC Link Inverter for Brushless Permanent Magnet Motors with Very Low Inductance  

SciTech Connect

Due to their long effective air gaps, permanent magnet motors tend to have low inductance. The use of ironless stator structure in present high power PM motors (several tens of kWs) reduces the inductance even further (< 100 {micro}H). This low inductance imposes stringent current regulation demands for the inverter to obtain acceptable current ripple. An analysis of the current ripple for these low inductance brushless PM motors shows that a standard inverter with the most commonly used IGBT switching devices cannot meet the current regulation demands and will produce unacceptable current ripples due to the IGBT's limited switching frequency. This paper introduces a new multilevel dc link inverter, which can dramatically reduce the current ripple for brushless PM motor drives. The operating principle and design guidelines are included.

Su, G.J.

2001-10-29T23:59:59.000Z

445

Gas Mileage of 1984 Vehicles by American Motors Corporation  

NLE Websites -- All DOE Office Websites (Extended Search)

4 American Motors Corporation Vehicles 4 American Motors Corporation Vehicles EPA MPG MODEL City Comb Hwy 1984 American Motors Corporation Eagle 4WD 4 cyl, 2.5 L, Manual 4-spd, Regular Gasoline Compare 1984 American Motors Corporation Eagle 4WD 19 City 20 Combined 22 Highway 1984 American Motors Corporation Eagle 4WD 4 cyl, 2.5 L, Manual 5-spd, Regular Gasoline Compare 1984 American Motors Corporation Eagle 4WD 19 City 21 Combined 23 Highway 1984 American Motors Corporation Eagle 4WD 6 cyl, 4.2 L, Automatic 3-spd, Regular Gasoline Compare 1984 American Motors Corporation Eagle 4WD 15 City 17 Combined 20 Highway 1984 American Motors Corporation Eagle 4WD 6 cyl, 4.2 L, Manual 4-spd, Regular Gasoline Compare 1984 American Motors Corporation Eagle 4WD 16 City 17 Combined 20 Highway 1984 American Motors Corporation Eagle 4WD 6 cyl, 4.2 L, Manual 5-spd, Regular Gasoline

446

Petroleum Gasoline & Distillate Needs Including the Energy ...  

U.S. Energy Information Administration (EIA)

Home > Petroleum > Analysis > Petroleum Gasoline & Distillate Needs Including the Energy Independence and Security Act (EISA) ...

447

Petroleum Gasoline & Distillate Needs Including the Energy ...  

U.S. Energy Information Administration (EIA)

Petroleum Gasoline & Distillate Needs Including the Energy Independence and Security Act (EISA) Impacts

448

Design and performance evaluation of an electric go-kart and custom permanent magnet brushless DC motor  

E-Print Network (OSTI)

This undergraduate thesis documents the design considerations and specifications of building a personal battery-powered go-kart. This includes designing and building a custom brushless DC motor for use in the drivetrain. ...

Davis, Eli Marc

2012-01-01T23:59:59.000Z

449

List of Motors Incentives | Open Energy Information  

Open Energy Info (EERE)

Incentives Incentives Jump to: navigation, search The following contains the list of 371 Motors Incentives. CSV (rows 1 - 371) Incentive Incentive Type Place Applicable Sector Eligible Technologies Active AEP (Central and North) - CitySmart Program (Texas) Utility Rebate Program Texas Commercial Industrial Institutional Local Government Schools Boilers Central Air conditioners Chillers Comprehensive Measures/Whole Building Custom/Others pending approval Energy Mgmt. Systems/Building Controls Furnaces Heat pumps Lighting Lighting Controls/Sensors Motor VFDs Motors Roofs Windows Yes AEP (Central, North and SWEPCO) - Commercial Solutions Program (Texas) Utility Rebate Program Texas Commercial Industrial Institutional Local Government Nonprofit Schools State Government Tribal Government Boilers

450

Report on Toyota Prius Motor Thermal Management  

DOE Green Energy (OSTI)

In the current hybrid vehicle market, the Toyota Prius drive system is considered the leader in electrical, mechanical, and manufacturing innovations. It is a significant accomplishment that Toyota is able to manufacture and sell the vehicle for a profit. The Toyota Prius traction motor design approach for reducing manufacturing costs and the motor s torque capability have been studied and tested. The findings were presented in two previous Oak Ridge National Laboratory (ORNL) reports. The conclusions from this report reveal, through temperature rise tests, that the 2004 Toyota Prius (THSII) motor is applicable only for use in a hybrid automobile. It would be significantly undersized if used in a fuel cell vehicle application. The power rating of the Prius motor is limited by the permissible temperature rise of the motor winding (170 C) and the motor cooling oil (158 C). The continuous ratings at base speed (1200 rpm) with different coolant temperatures are projected from test data at 900 rpm. They are approximately 15 kW with 105 C coolant and 21 kW with 35 C coolant. These continuous ratings are much lower than the 30 kW specified as a technical motor target of the U.S. Department of Energy FreedomCAR Program. All tests were conducted at about 24 C ambient temperature. The load angle of each torque adjustment was monitored to prevent a sudden stop of the motor if the peak torque were exceeded, as indicated by the load angle in the region greater than 90 electrical degrees. For peak power with 400 Nm torque at 1200 rpm, the permissible running time depends upon the initial winding temperature condition. The projected rate of winding temperature rise is approximately 2.1 C/sec. The cooling-oil temperature does not change much during short peak power operation. For light and medium load situations, the efficiency varies from 80% to above 90%, and the power factor varies from 70% to above 90%, depending on the load and speed. When the motor is loaded heavily near the peak-torque (400-Nm) region, the efficiency goes down to the 40-50% range, and the power factor is nearly 100%. The efficiency is not a major concern at the high-torque region. The water-ethylene-glycol heat exchanger attached to the motor is small. During continuous operation, it dissipates about 76% of the total motor heat loss with 35 C coolant. The heat exchanger is less effective when the coolant temperature increases. With 75 C coolant, the heat exchanger dissipates about 38% of the motor heat. When the coolant temperature is 105 C, the heat exchanger not only stops cooling the motor but also adds heat to the large motor housing that acts as an air-cooled heat sink. From start to the base speed, 400 Nms of torque can be produced by the Prius motor with a reasonably low stator current. However, the permissible running time of the motor depends on the load drawn from the motor and the coolant temperature. In the Toyota Prius hybrid configuration, if the motor gets too hot and cannot keep running, the load can be shifted back to the engine. The motor acts to improve the system efficiency without being overly designed. A detailed thermal model was developed to help predict the temperature levels in key motor components. The model was calibrated and compared with the experimentally measured temperatures. Very good agreement was obtained between model and experiment. This model can now be used to predict the temperature of key motor components at a variety of operating conditions and to evaluate the thermal characteristics of new motor designs. It should be pointed out that a fuel-cell motor does not have an engine to fall back on to provide the needed wheel power. Therefore, the design philosophy of a fuel-cell motor is very different from that of a hybrid Prius motor. Further thermal management studies in the high-speed region of the Prius motor, fed by its inverter, are planned.

Hsu, J.S.

2005-02-11T23:59:59.000Z

451

Comparison of Photoluminescence Imaging on Starting Multi-Crystalline Silicon Wafers to Finished Cell Performance: Preprint  

DOE Green Energy (OSTI)

Photoluminescence (PL) imaging techniques can be applied to multicrystalline silicon wafers throughout the manufacturing process. Both band-to-band PL and defect-band emissions, which are longer-wavelength emissions from sub-bandgap transitions, are used to characterize wafer quality and defect content on starting multicrystalline silicon wafers and neighboring wafers processed at each step through completion of finished cells. Both PL imaging techniques spatially highlight defect regions that represent dislocations and defect clusters. The relative intensities of these imaged defect regions change with processing. Band-to-band PL on wafers in the later steps of processing shows good correlation to cell quality and performance. The defect band images show regions that change relative intensity through processing, and better correlation to cell efficiency and reverse-bias breakdown is more evident at the starting wafer stage as opposed to later process steps. We show that thermal processing in the 200 degrees - 400 degrees C range causes impurities to diffuse to different defect regions, changing their relative defect band emissions.

Johnston, S.; Yan, F.; Dorn, D.; Zaunbrecher, K.; Al-Jassim, M.; Sidelkheir, O.; Ounadjela, K.

2012-06-01T23:59:59.000Z

452

History and stabilization of the Plutonium Finishing Plant (PFP) complex, Hanford Site  

Science Conference Proceedings (OSTI)

The 231-Z Isolation Building or Plutonium Metallurgy Building is located in the Hanford Site`s 200 West Area, approximately 300 yards north of the Plutonium Finishing Plant (PFP) (234-5 Building). When the Hanford Engineer Works (HEW) built it in 1944 to contain the final step for processing plutonium, it was called the Isolation Building. At that time, HEW used a bismuth phosphate radiochemical separations process to make `AT solution,` which was then dried and shipped to Los Alamos, New Mexico. (AT solution is a code name used during World War II for the final HEW product.) The process was carried out first in T Plant and the 224-T Bulk Reduction Building and B Plant and the 224-B Bulk Reduction Building. The 224-T and -B processes produced a concentrated plutonium nitrate stream, which then was sent in 8-gallon batches to the 231-Z Building for final purification. In the 231-Z Building, the plutonium nitrate solution underwent peroxide `strikes` (additions of hydrogen peroxide to further separate the plutonium from its carrier solutions), to form the AT solution. The AT solution was dried and shipped to the Los Alamos Site, where it was made into metallic plutonium and then into weapons hemispheres.` The 231-Z Building began `hot` operations (operations using radioactive materials) with regular runs of plutonium nitrate on January 16, 1945.

Gerber, M.S., Fluor Daniel Hanford

1997-02-18T23:59:59.000Z

453

A University of Alabama Axial-Gap Electric Motor Developmenty  

E-Print Network (OSTI)

­ Develop axial gap permanent-magnet electric Axial motor ­ Develop axial gap permanent-magnet electricCAVT A University of Alabama Axial-Gap Electric Motor Developmenty Research Center OBJECTIVE motor topologies with high torque and power densities MOTIVATION ­ Axial-gap ("pancake") motors have

Carver, Jeffrey C.

454

Motor transport of self-assembled cargos in crowded environments  

E-Print Network (OSTI)

Motor transport of self-assembled cargos in crowded environments Leslie Conwaya , Derek Woodb is performed by multiple motors working in concert. However, the mechanism of motor association to cargos is unknown. It is also unknown how long individual motors stay attached, how many are active, and how

Ross, Jennifer

455

Motor Wave Group | Open Energy Information  

Open Energy Info (EERE)

Wave Group Jump to: navigation, search Name Motor Wave Group Place Hong Kong Sector Marine and Hydrokinetic Website http:www.motorwavegroup.com Region China LinkedIn Connections...

456

Dynamic Phase Transitions in Coupled Motor Proteins  

E-Print Network (OSTI)

The effect of interactions on dynamics of coupled motor proteins is investigated theoretically. A simple stochastic discrete model, that allows to calculate explicitly the dynamic properties of the system, is developed. It is shown that there are two dynamic regimes, depending on the interaction between the particles. For strong interactions the motor proteins move as one tight cluster, while for weak interactions there is no correlation in the motion of the proteins, and the particle separation increases steadily with time. The boundary between two dynamic phases is specified by a critical interaction that has a non-zero value only for the coupling of the asymmetric motor proteins, and it depends on the temperature and the transitions rates. At the critical interaction there is a change in a slope for the mean velocities and a discontinuity in the dispersions of the motor proteins as a function of the interaction energy.

Evgeny B. Stukalin; Anatoly B. Kolomeisky

2005-09-16T23:59:59.000Z

457

The Paris Motor Show | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Paris Motor Show Paris Motor Show The Paris Motor Show October 4, 2010 - 9:39am Addthis David Sandalow at the Paris Auto Show | DOE photo David Sandalow at the Paris Auto Show | DOE photo David Sandalow David Sandalow Former Under Secretary of Energy (Acting) and Assistant Secretary for Policy & International Affairs At the Paris Motor Show today, electric cars are everywhere. Chevrolet is showing off the Volt, its plug-in hybrid due in U.S. showrooms this December. (Motown music blared as a Chevy rep told me all about the car's performance.) Nissan is displaying the Leaf, its all-electric sedan scheduled to roll off assembly lines in Tennessee starting in 2012. Volvo has new plug-in models. So do Saab, Peugot and other European manufacturers. And as I walked through the gates in a huge crowd, the first

458

The Paris Motor Show | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

The Paris Motor Show The Paris Motor Show The Paris Motor Show October 4, 2010 - 9:39am Addthis David Sandalow at the Paris Auto Show | DOE photo David Sandalow at the Paris Auto Show | DOE photo David Sandalow David Sandalow Former Under Secretary of Energy (Acting) and Assistant Secretary for Policy & International Affairs At the Paris Motor Show today, electric cars are everywhere. Chevrolet is showing off the Volt, its plug-in hybrid due in U.S. showrooms this December. (Motown music blared as a Chevy rep told me all about the car's performance.) Nissan is displaying the Leaf, its all-electric sedan scheduled to roll off assembly lines in Tennessee starting in 2012. Volvo has new plug-in models. So do Saab, Peugot and other European manufacturers. And as I walked through the gates in a huge crowd, the first

459

Isolated Multiple Flux Path (IMFP) Reluctance Motors  

2 Managed by UT-Battelle for the U.S. Department of Energy Overview IMFP reluctance electric motor developed for passenger vehicle propulsion (i.e. small trucks ...

460

Modeling and optimization of permanent magnetic motors  

E-Print Network (OSTI)

This thesis develops analytic models for the prediction and optimization of radial-flux permanent magnet motor torque and efficiency. It also facilitates the design optimization of electromagnetically-powered rotorcraft ...

Pinkham, Andrew P

2008-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "includes finished motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Real Time Flux Control in PM Motors  

SciTech Connect

Significant research at the Oak Ridge National Laboratory (ORNL) Power Electronics and Electric Machinery Research Center (PEEMRC) is being conducted to develop ways to increase (1) torque, (2) speed range, and (3) efficiency of traction electric motors for hybrid electric vehicles (HEV) within existing current and voltage bounds. Current is limited by the inverter semiconductor devices' capability and voltage is limited by the stator wire insulation's ability to withstand the maximum back-electromotive force (emf), which occurs at the upper end of the speed range. One research track has been to explore ways to control the path and magnitude of magnetic flux while the motor is operating. The phrase, real time flux control (RTFC), refers to this mode of operation in which system parameters are changed while the motor is operating to improve its performance and speed range. RTFC has potential to meet an increased torque demand by introducing additional flux through the main air gap from an external source. It can augment the speed range by diverting flux away from the main air gap to reduce back-emf at high speeds. Conventional RTFC technology is known as vector control [1]. Vector control decomposes the stator current into two components; one that produces torque and a second that opposes (weakens) the magnetic field generated by the rotor, thereby requiring more overall stator current and reducing the efficiency. Efficiency can be improved by selecting a RTFC method that reduces the back-emf without increasing the average current. This favors methods that use pulse currents or very low currents to achieve field weakening. Foremost in ORNL's effort to develop flux control is the work of J. S. Hsu. Early research [2,3] introduced direct control of air-gap flux in permanent magnet (PM) machines and demonstrated it with a flux-controlled generator. The configuration eliminates the problem of demagnetization because it diverts all the flux from the magnets instead of trying to oppose it. It is robust and could be particularly useful for PM generators and electric vehicle drives. Recent efforts have introduced a brushless machine that transfers a magneto-motive force (MMF) generated by a stationary excitation coil to the rotor [4]. Although a conventional PM machine may be field weakened using vector control, the air-gap flux density cannot be effectively enhanced. In Hsu's new machine, the magnetic field generated by the rotor's PM may be augmented by the field from the stationery excitation coil and channeled with flux guides to its desired destination to enhance the air-gap flux that produces torque. The magnetic field can also be weakened by reversing the current in the stationary excitation winding. A patent for advanced technology in this area is pending. Several additional RTFC methods have been discussed in open literature. These include methods of changing the number of poles by magnetizing and demagnetizing the magnets poles with pulses of current corresponding to direct-axis (d-axis) current of vector control [5,6], changing the number of stator coils [7], and controlling the air gap [8]. Test experience has shown that the magnet strengths may vary and weaken naturally as rotor temperature increases suggesting that careful control of the rotor temperature, which is no easy task, could yield another method of RTFC. The purpose of this report is to (1) examine the interaction of rotor and stator flux with regard to RTFC, (2) review and summarize the status of RTFC technology, and (3) compare and evaluate methods for RTFC with respect to maturity, advantages and limitations, deployment difficulty and relative complexity.

Otaduy, P.J.

2005-09-27T23:59:59.000Z

462

Development of a gross motor task to assess motor planning of children with autism spectrum disorders.  

E-Print Network (OSTI)

??Motor planning was assessed by performance of 10 male children (age range 9-12 years) with ASD on a simple obstacle course of horizontal barriers. The (more)

Staples, Kerri.

2005-01-01T23:59:59.000Z

463

ORIGINAL ARTICLE Low Motor Assessment: A Comparative Pilot Study with Young Children With and Without Motor  

E-Print Network (OSTI)

# The Author(s) 2009. This article is published with open access at Springerlink.com Abstract Most of the developmental instruments that measure cognitive development in children rely heavily on fine motor skills, especially for young children whose language skills are not yet well developed. This is problematic when evaluating the cognitive development of young children with motor impairment. The purpose of this study is to assess the need for a Low Motor adapation of a standardized instrument when testing children with motor impairment. To accomplish this, we have adapted the procedures, item instructions and play material of a widely used and standardized instrument, the Bayley Scales of Infant Development-Second Edition (BSID-II, Bayley 1993). The Original and the Low Motor versions were administered to 20 children experiencing typical development and 19 children with motor impairment within a period of two weeks. Results showed that children with motor impairments scored significantly higher on the Low Motor version of the Bayley Mental Scale than on the Original version: a difference of between 5 and 10 points when the score is expressed in terms of a developmental index score. Results from children with typical development support the assumption that item content and difficulty remain unchanged in the Low Motor version.

J Dev Phys Disabil; Selma Anne; Jos Ruiter; Han Nakken; Bieuwe F. Van Der Meulen; Carolien B. Lunenborg

2009-01-01T23:59:59.000Z

464

DC Motor control using motor-generator set with controlled generator field  

DOE Patents (OSTI)

A d.c. generator is connected in series opposed to the polarity of a d.c. power source supplying a d.c. drive motor. The generator is part of a motor-generator set, the motor of which is supplied from the power source connected to the motor. A generator field control means varies the field produced by at least one of the generator windings in order to change the effective voltage output. When the generator voltage is exactly equal to the d.c. voltage supply, no voltage is applied across the drive motor. As the field of the generator is reduced, the drive motor is supplied greater voltage until the full voltage of the d.c. power source is supplied when the generator has zero field applied. Additional voltage may be applied across the drive motor by reversing and increasing the reversed field on the generator. The drive motor may be reversed in direction from standstill by increasing the generator field so that a reverse voltage is applied across the d.c. motor.

Belsterling, Charles A. (Norristown, PA); Stone, John (Medford, NJ)

1982-01-01T23:59:59.000Z

465

Fluctuating-friction molecular motors  

E-Print Network (OSTI)

We show that the correlated stochastic fluctuation of the friction coefficient can give rise to long-range directional motion of a particle undergoing Brownian random walk in a constant periodic energy potential landscape. The occurrence of this motion requires the presence of two additional independent bodies interacting with the particle via friction and via the energy potential, respectively, which can move relative to each other. Such three-body system generalizes the classical Brownian ratchet mechanism, which requires only two interacting bodies. In particular, we describe a simple two-level model of fluctuating-friction molecular motor that can be solved analytically. In our previous work [M.K., L.M and D.P. 2000 J. Nonlinear Opt. Phys. Mater. vol. 9, 157] this model has been first applied to understanding the fundamental mechanism of the photoinduced reorientation of dye-doped liquid crystals. Applications of the same idea to other fields such as molecular biology and nanotechnology can however be envisioned. As an example, in this paper we work out a model of the actomyosin system based on the fluctuating-friction mechanism.

Lorenzo Marrucci; Domenico Paparo; Markus Kreuzer

2001-10-12T23:59:59.000Z

466

Motor vehicles and global warming  

SciTech Connect

Energy use in transportation is one of the contributors to the concern over global warming. The primary greenhouse gases released by the transportation sector are carbon dioxide and chlorofluorocarbons. When all greenhouse gases are considered, CO{sub 2} emissions from the operation of highway vehicles worldwide represent about 4.7% of global warming enhancement. CO{sub 2} emissions from U.S. highway vehicles along represent about 2 to 2.5% of worldwide greenhouse gases. The use of CFCs in automotive air conditioning, in blowing foams for seats and padding and in the manufacture of electronic circuit boards accounted for 15% of the global usage of CFC-12 in 1985 according to the U.S. EPA. The Motor Vehicle Manufacturers Association supports the phase-out of CFC use provided that safe substitutes are available and that adequate lead time is allowed for.They suggest that reduction of greenhouse gases would require planning on a global scope to be effective. One alternative they suggest for further study is a carbon fee for reducing emissions of carbon dioxide. This fee would be levied on each type of fossil fuel, proportional to its carbon content per unit of energy.

Halberstadt, M.L.

1990-03-01T23:59:59.000Z

467

ac-driven atomic quantum motor  

E-Print Network (OSTI)

We invent an ac-driven quantum motor consisting of two different, interacting ultracold atoms placed into a ring-shaped optical lattice and submerged in a pulsating magnetic field. While the first atom carries a current, the second one serves as a quantum starter. For fixed zero-momentum initial conditions the asymptotic carrier velocity converges to a unique non-zero value. We also demonstrate that this quantum motor performs work against a constant load.

A. V. Ponomarev; S. Denisov; P. Hanggi

2009-02-03T23:59:59.000Z

468

ac-driven atomic quantum motor  

E-Print Network (OSTI)

We invent an ac-driven quantum motor consisting of two different, interacting ultracold atoms placed into a ring-shaped optical lattice and submerged in a pulsating magnetic field. While the first atom carries a current, the second one serves as a quantum starter. For fixed zero-momentum initial conditions the asymptotic carrier velocity converges to a unique non-zero value. We also demonstrate that this quantum motor performs work against a constant load.

Ponomarev, A V; Hnggi, P

2009-01-01T23:59:59.000Z

469

Alternative Fuels Data Center: Alternative Fuel Motor Carrier Fuel Tax  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Fuel Motor Fuel Motor Carrier Fuel Tax to someone by E-mail Share Alternative Fuels Data Center: Alternative Fuel Motor Carrier Fuel Tax on Facebook Tweet about Alternative Fuels Data Center: Alternative Fuel Motor Carrier Fuel Tax on Twitter Bookmark Alternative Fuels Data Center: Alternative Fuel Motor Carrier Fuel Tax on Google Bookmark Alternative Fuels Data Center: Alternative Fuel Motor Carrier Fuel Tax on Delicious Rank Alternative Fuels Data Center: Alternative Fuel Motor Carrier Fuel Tax on Digg Find More places to share Alternative Fuels Data Center: Alternative Fuel Motor Carrier Fuel Tax on AddThis.com... More in this section... Federal State Advanced Search All Laws & Incentives Sorted by Type Alternative Fuel Motor Carrier Fuel Tax Effective January 1, 2014, a person who operates a commercial motor vehicle

470

Halbach array DC motor/generator  

DOE Patents (OSTI)

A new configuration of DC motor/generator is based on a Halbach array of permanent magnets. This motor does not use ferrous materials so that the only losses are winding losses and losses due to bearings and windage. An "inside-out" design is used as compared to a conventional motor/generator design. The rotating portion, i.e., the rotor, is on the outside of the machine. The stationary portion, i.e., the stator, is formed by the inside of the machine. The rotor contains an array of permanent magnets that provide a uniform field. The windings of the motor are placed in or on the stator. The stator windings are then "switched" or "commutated" to provide a DC motor/generator much the same as in a conventional DC motor. The commutation can be performed by mechanical means using brushes or by electronic means using switching circuits. The invention is useful in electric vehicles and adjustable speed DC drives.

Merritt, Bernard T. (Livermore, CA); Dreifuerst, Gary R. (Livermore, CA); Post, Richard F. (Walnut Creek, CA)

1998-01-01T23:59:59.000Z

471

Halbach array DC motor/generator  

DOE Patents (OSTI)

A new configuration of DC motor/generator is based on a Halbach array of permanent magnets. This motor does not use ferrous materials so that the only losses are winding losses and losses due to bearings and windage. An ``inside-out`` design is used as compared to a conventional motor/generator design. The rotating portion, i.e., the rotor, is on the outside of the machine. The stationary portion, i.e., the stator, is formed by the inside of the machine. The rotor contains an array of permanent magnets that provide a uniform field. The windings of the motor are placed in or on the stator. The stator windings are then ``switched`` or ``commutated`` to provide a DC motor/generator much the same as in a conventional DC motor. The commutation can be performed by mechanical means using brushes or by electronic means using switching circuits. The invention is useful in electric vehicles and adjustable speed DC drives. 17 figs.

Merritt, B.T.; Dreifuerst, G.R.; Post, R.F.

1998-01-06T23:59:59.000Z

472

Motor Pool Department The Motor Pool Department is responsible for the maintenance of over 550 Georgia Tech state  

E-Print Network (OSTI)

Motor Pool Department The Motor Pool Department is responsible for the maintenance of over 550 and equipment costing $3,000 or more for the Institute's vehicle fleet program. The mission of the Motor Pool form when bringing their vehicles, LSVs, golf carts or equipment to the Motor Pool for service (see

Li, Mo

473

Contol of Surface Mounted Permanent Magnet Motors with Special Application to Motors with Fractional-Slot Concentrated Windings  

SciTech Connect

A 30-pole, 6-kW prototype of a fractional-slot permanent magnet synchronous motor (PMSM) design has been developed to operate at a maximum speed of 6000 rpm [1,2]. This machine has significantly more inductance than regular PMSMs with distributed windings. The prototype was delivered in April 2006 to the Oak Ridge National Laboratory (ORNL) for testing and development of a suitable controller. To prepare for this test/control development effort, ORNL used PMSM models developed over a number of previous studies to preview the control issues that arise when a dynamic controller drives a high inductance PMSM machine during steady state performance evaluations. The detailed steady state model developed includes all motor and inverter loss mechanisms and was useful for assessing the performance of the dynamic controller before it was put into operation. This report documents the results of tests demonstrating the effectiveness of ORNL's simple low-cost control scheme during characterization of the fractional-slot concentrated windings (FSCW) PMSM motor. The control scheme is simple because only the supply voltage magnitude and the phase angle between the back-electromotive force (emf) and the supply voltage is controlled. It is low-cost because it requires no current or phase voltage sensors.

Patil, N.; Lawler, J.S.; McKeever, J.

2007-07-31T23:59:59.000Z

474

Contol of Surface Mounted Permanent Magnet Motors with Special Application to Motors with Fractional-Slot Concentrated Windings  

SciTech Connect

A 30-pole, 6-kW prototype of a fractional-slot permanent magnet synchronous motor (PMSM) design has been developed to operate at a maximum speed of 6000 rpm [1,2]. This machine has significantly more inductance than regular PMSMs with distributed windings. The prototype was delivered in April 2006 to the Oak Ridge National Laboratory (ORNL) for testing and development of a suitable controller. To prepare for this test/control development effort, ORNL used PMSM models developed over a number of previous studies to preview the control issues that arise when a dynamic controller drives a high inductance PMSM machine during steady state performance evaluations. The detailed steady state model developed includes all motor and inverter loss mechanisms and was useful for assessing the performance of the dynamic controller before it was put into operation. This report documents the results of tests demonstrating the effectiveness of ORNL's simple low-cost control scheme during characterization of the fractional-slot concentrated windings (FSCW) PMSM motor. The control scheme is simple because only the supply voltage magnitude and the phase angle between the back-electromotive force (emf) and the supply voltage is controlled. It is low-cost because it requires no current or phase voltage sensors.

Patil, N.; Lawler, J.S.; McKeever, J.

2007-07-31T23:59:59.000Z

475

Dual capacity compressor with reversible motor and controls arrangement therefor  

DOE Patents (OSTI)

A hermetic reciprocating compressor such as may be used in heat pump applications is provided for dual capacity operation by providing the crankpin of the crankshaft with an eccentric ring rotatably mounted thereon, and with the end of the connecting rod opposite the piston encompassing the outer circumference of the eccentric ring, with means limiting the rotation of the eccentric ring upon the crankpin between one end point and an opposite angularly displaced end point to provide different values of eccentricity depending upon which end point the eccentric ring is rotated to upon the crankpin, and a reversible motor in the hermetic shell of the compressor for rotating the crankshaft, the motor operating in one direction effecting the angular displacement of the eccentric ring relative to the crankpin to the one end point, and in the opposite direction effecting the angular displacement of the eccentric ring relative to the crankpin to the opposite end point, this arrangement automatically giving different stroke lengths depending upon the direction of motor rotation. The mechanical structure of the arrangement may take various forms including at least one in which any impact of reversal is reduced by utilizing lubricant passages and chambers at the interface area of the crankpin and eccentric ring to provide a dashpot effect. In the main intended application of the arrangement according to the invention, that is, in a refrigerating or air conditioning system, it is desirable to insure a delay during reversal of the direction of compressor operation. A control arrangement is provided in which the control system controls the direction of motor operation in accordance with temperature conditions, the system including control means for effecting operation in a low capacity direction or alternatively in a high capacity direction in response to one set, and another set, respectively, of temperature conditions and with timer means delaying a restart of the compressor motor for at least a predetermined time in response to a condition of the control means operative to initiate a change in the operating direction of the compressor when it restarts.

Sisk, Francis J. (Washington Township, Fayette County, PA)

1980-12-02T23:59:59.000Z

476

Method of electrolytically finishing spray-hole of fuel injection nozzle  

SciTech Connect

This patent describes a method of finishing at least one spray-hole bored by machining in a body of a fuel injection nozzle for an internal combustion engine by removing burrs that remain after the machining around an inside mouth of each spray-hole. The method consists of subjecting an inner surface of the nozzle body in an area containing the inside mouth of each spray-hole to an electrolytic polishing treatment. The nozzle body is made the anode by inserting a tubular electrode having an insulator cover into the nozzle body such that an end portion of the electrode comes close to each spray-hole and supplies a pressurized electrolyte liquid into the interior of the nozzle body through the tubular electrode to flow out through each spray-hole. The method is characterized in that a portion of the insulator cover is so formed as to completely cover the end portion of the electrode. An outer surface makes close contact with the area of the inner surface of the nozzle body, that for each spray-hole the insulator cover is formed with a liquid passage which communicates with the interior of the tubular electrode and has an outlet port in the outer spray-hole and is only slightly larger in diameter than the mouth of the spray-hole. During the electrolytic polishing treatment, the electrolyte liquid is supplied through the tubular electrode flow out of the insulator cover only through the passage formed for each spray-hole.

Matsui, Y.; Uchiyama, M.

1986-03-25T23:59:59.000Z

477

Single phase four pole/six pole motor  

DOE Patents (OSTI)

A single phase alternating current electric motor is provided with a main stator winding having two coil groups each including the series connection of three coils. These coil groups can be connected in series for six pole operation and in parallel for four pole operation. The coils are approximately equally spaced around the periphery of the machine but are not of equal numbers of turns. The two coil groups are identically wound and spaced 180 mechanical degrees apart. One coil of each group has more turns and a greater span than the other two coils. 10 figs.

Kirschbaum, H.S.

1984-10-09T23:59:59.000Z

478

Development of Integrated Motor Assist Hybrid System: Development of the 'Insight', a Personal Hybrid Coupe  

DOE Green Energy (OSTI)

This paper presents the technical approach used to design and develop the powerplant for the Honda Insight, a new motor assist hybrid vehicle with an overall development objective of just half the fuel consumption of the current Civic over a wide range of driving conditions. Fuel consumption of 35km/L (Japanese 10-15 mode), and 3.4L/100km (98/69/EC) was realized. To achieve this, a new Integrated Motor Assist (IMA) hybrid power plant system was developed, incorporating many new technologies for packaging and integrating the motor assist system and for improving engine thermal efficiency. This was developed in combination with a new lightweight aluminum body with low aerodynamic resistance. Environmental performance goals also included the simultaneous achievement of low emissions (half the Japanese year 2000 standards, and half the EU2000 standards), high efficiency, and recyclability. Full consideration was also given to key consumer attributes, including crash safety performance, handling, and driving performance.

Kaoru Aoki; Shigetaka Kuroda; Shigemasa Kajiwara; Hiromitsu Sato; Yoshio Yamamoto

2000-06-19T23:59:59.000Z

479

Stocks of Total Motor Gasoline  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: Stocks include those ...

480

Demonstration of an inductor motor/alternator/flywheel energy storage system. Quarterly progress report No. 1, June 28, 1976--September 28, 1976  

SciTech Connect

Vehicle propulsion concepts utilizing flywheel energy are described. Analyses are presented for sizing an inductor motor/alternator/flywheel for application to a 3000 pound vehicle. Component tradeoffs are included for the inductor motor/alternator drive, the solid state inverter/rectifier, the control circuit, and a composite flywheel. Design specifications for the machine are established and a test plan defined.

1976-09-28T23:59:59.000Z

Note: This page contains sample records for the topic "includes finished motor" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Alternative Fuels Data Center: Natural Gas Motor Vehicle Fuel Promotion  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Natural Gas Motor Natural Gas Motor Vehicle Fuel Promotion to someone by E-mail Share Alternative Fuels Data Center: Natural Gas Motor Vehicle Fuel Promotion on Facebook Tweet about Alternative Fuels Data Center: Natural Gas Motor Vehicle Fuel Promotion on Twitter Bookmark Alternative Fuels Data Center: Natural Gas Motor Vehicle Fuel Promotion on Google Bookmark Alternative Fuels Data Center: Natural Gas Motor Vehicle Fuel Promotion on Delicious Rank Alternative Fuels Data Center: Natural Gas Motor Vehicle Fuel Promotion on Digg Find More places to share Alternative Fuels Data Center: Natural Gas Motor Vehicle Fuel Promotion on AddThis.com... More in this section... Federal State Advanced Search All Laws & Incentives Sorted by Type Natural Gas Motor Vehicle Fuel Promotion An eight member Natural Gas Fuel Board (Board) was created to advise the

482

Alternative Fuels Data Center: Fuel Cell Motor Vehicle Tax Credit  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Fuel Cell Motor Fuel Cell Motor Vehicle Tax Credit to someone by E-mail Share Alternative Fuels Data Center: Fuel Cell Motor Vehicle Tax Credit on Facebook Tweet about Alternative Fuels Data Center: Fuel Cell Motor Vehicle Tax Credit on Twitter Bookmark Alternative Fuels Data Center: Fuel Cell Motor Vehicle Tax Credit on Google Bookmark Alternative Fuels Data Center: Fuel Cell Motor Vehicle Tax Credit on Delicious Rank Alternative Fuels Data Center: Fuel Cell Motor Vehicle Tax Credit on Digg Find More places to share Alternative Fuels Data Center: Fuel Cell Motor Vehicle Tax Credit on AddThis.com... More in this section... Federal State Advanced Search All Laws & Incentives Sorted by Type Fuel Cell Motor Vehicle Tax Credit A tax credit of up to $4,000 is available for the purchase of qualified

483

Alternative Fuels Data Center: Fuel Cell Motor Vehicle Tax Deduction  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Fuel Cell Motor Fuel Cell Motor Vehicle Tax Deduction to someone by E-mail Share Alternative Fuels Data Center: Fuel Cell Motor Vehicle Tax Deduction on Facebook Tweet about Alternative Fuels Data Center: Fuel Cell Motor Vehicle Tax Deduction on Twitter Bookmark Alternative Fuels Data Center: Fuel Cell Motor Vehicle Tax Deduction on Google Bookmark Alternative Fuels Data Center: Fuel Cell Motor Vehicle Tax Deduction on Delicious Rank Alternative Fuels Data Center: Fuel Cell Motor Vehicle Tax Deduction on Digg Find More places to share Alternative Fuels Data Center: Fuel Cell Motor Vehicle Tax Deduction on AddThis.com... More in this section... Federal State Advanced Search All Laws & Incentives Sorted by Type Fuel Cell Motor Vehicle Tax Deduction A taxpayer is eligible for a $2,000 tax deduction for the purchase of a

484

Gas storage materials, including hydrogen storage materials  

DOE Patents (OSTI)

A material for the storage and release of gases comprises a plurality of hollow elements, each hollow element comprising a porous wall enclosing an interior cavity, the interior cavity including structures of a solid-state storage material. In particular examples, the storage material is a hydrogen storage material such as a solid state hydride. An improved method for forming such materials includes the solution diffusion of a storage material solution through a porous wall of a hollow element into an interior cavity.

Mohtadi, Rana F; Wicks, George G; Heung, Leung K; Nakamura, Kenji

2013-02-19T23:59:59.000Z

485

Motor function in interpolar microtubules during metaphase  

E-Print Network (OSTI)

We analyze experimental observations of microtubules undergoing small fluctuations about a "balance point" when mixed in solution of two different kinesin motor proteins, KLP61F and Ncd. It has been proposed that the microtubule movement is due to stochastic variations in the densities of the two species of motor proteins. We test this hypothesis here by showing how it maps onto a one-dimensional random walk in a random environment. Our estimate of the amplitude of the fluctuations agrees with experimental observations. We point out that there is an initial transient in the position of the microtubule where it will typically move of order its own length. We compare the physics of this gliding assay to a recent theory of the role of antagonistic motors on restricting interpolar microtubule sliding of a cell's mitotic spindle during prometaphase. It is concluded that randomly positioned antagonistic motors can restrict relative movement of microtubules, however they do so imperfectly. A variation in motor concentrations is also analyzed and shown to lead to greater control of spindle length.

J. M. Deutsch; Ian P. Lewis

2013-07-22T23:59:59.000Z

486

Tecnologías del Motor  

NLE Websites -- All DOE Office Websites (Extended Search)

del Motor del Motor El Tiempo de apertura y Levantamiento de Válvulas Variable (VVT&L) Motor con Válvulas de Tiempo y Elevación Variable También llamado activación variable de válvulas (AVV), elevación variable y tiempo variable y control electrónico de elevación (VTEC®). Las válvulas controlan el flujo de aire y combustible de los cilindros y los expulsa fuera de ellos. El momento y el tiempo que las válvulas permanecen abiertas y cómo se mueven o se elevan, ambos afectan la eficiencia del motor. Los ajustes en el tiempo y elevación son diferentes para motores de baja y alta velocidad. De cualquier manera en los diseños tradicionales se usan tiempos y elevaciones "arregladas" lo cual compromete los valores óptimos entre las velocidades altas y bajas. Los sistemas VVT&L alteran el tiempo y

487

Sequence learning in pianists and nonpianists: An fMRI study of motor expertise  

E-Print Network (OSTI)

related changes in human motor function. Neurology, Meister,brief practice of a simple motor task. Cognitive Brain1996). Asymmetry in the human motor cortex and handedness.

Landau, Susan M; D'esposito, Mark

2006-01-01T23:59:59.000Z

488

A Multi-Country Analysis of Lifecycle Emissions From Transportation Fuels and Motor Vehicles  

E-Print Network (OSTI)

from Transportation Fuels, Motor Vehicles, Transportationfrom alternative fuels for motor vehicles and electricity-Environmental Externalities of Motor-Vehicle Use in the U.

Delucchi, Mark

2005-01-01T23:59:59.000Z

489

Sub-threshold spinal cord stimulation facilitates spontaneous motor activity in spinal rats  

E-Print Network (OSTI)

facilitates spontaneous motor activity in spinal rats.facilitates spontaneous motor activity in spinal rats Paragtreadmill (electrical enabling motor control, eEmc) after a

2013-01-01T23:59:59.000Z

490

Emergency Department Visits by Older Adults for Motor Vehicle Collisions: A Five-Year National Study  

E-Print Network (OSTI)

KM, Esserman DA, et al. Motor vehicle collision-relatedVisits by Older Adults for Motor Vehicle Collisions * Denvervisits by older adults for motor vehicle collisions (MVC) in

Vogel, Jody A; Ginde, Adit A.; Lowenstein, Steven R.; Betz, Marian E.

2013-01-01T23:59:59.000Z

491

Vital Signs: Emergency Department and Older Adult Motor Vehicle Collisions: Prevention is Paramount  

E-Print Network (OSTI)

Severity of Older Adult Motor Vehicle Collisions in OrangeOlder adults opinion of and motor vehicle-related crashes32. California Department of Motor Vehicles. Senior Driver:

Lotfipour, Shahram; Cisneros, Victor; Chakravarthy, Bharath

2013-01-01T23:59:59.000Z

492

Dissecting the Operating Mechanism of a Biological Motor One Molecule at a Time  

E-Print Network (OSTI)

a viral DNA packaging motor. Nature 461, 669-673 Abrahams,of High Resolution Recordings of Motor Movement, Biophysicalstructure of the dynein motor domain. Science 331, 1159-

Chistol, Gheorghe

2013-01-01T23:59:59.000Z

493

Coupled simulation of an indirect field oriented controlled induction motor drive.  

E-Print Network (OSTI)

??Conventionally, system simulations of induction motor drives use lumped parameters model of the motor. This approach assumes motor parameters to be constant during the entire (more)

Legesse, Michael.

2008-01-01T23:59:59.000Z

494

The role of brain-derived neurotrophic factor in cortical motor learning  

E-Print Network (OSTI)

organization of adult motor cortex is dependent uponorganization of primary motor cortex output to targetreorganization following motor nerve lesions. Exp Brain Res,

Von dem Bussche, Mary

2007-01-01T23:59:59.000Z

495

Impacts of motor vehicle operation on water quality - Clean-up Costs and Policies  

E-Print Network (OSTI)

preventing water pollution from motor vehicles would be muchgroundwater pollution; motor-vehicle transportation;the environmental costs of motor vehicle transportation in

Nixon, Hilary; Saphores, Jean-Daniel M

2007-01-01T23:59:59.000Z

496

The Sex Chromosome Trisomy mouse model of XXY and XYY: metabolism and motor performance  

E-Print Network (OSTI)

synuclein shows improvement in motor function and reductionof XXY and XYY: metabolism and motor performance. Biology ofand XYY: metabolism and motor performance Xuqi Chen 1,3 ,

2013-01-01T23:59:59.000Z

497

A MULTI-COUNTRY ANALYSIS OF LIFECYCLE EMISSIONS FROM TRANSPORTATION FUELS AND MOTOR VEHICLES  

E-Print Network (OSTI)

from Transportation Fuels, Motor Vehicles, Transportationfrom alternative fuels for motor vehicles and electricity-Environmental Externalities of Motor-Vehicle Use in the U.

Delucchi, Mark

2005-01-01T23:59:59.000Z

498

How large are tax subsidies to motor-vehicle users in the US?  

E-Print Network (OSTI)

of this deriving from motor fuels (the oil industry) ratherincome (%) Income year 1991 a Oil industries Motor vehicleindustries Oil and motor vehicle industries combined Amount

Delucchi, Mark; Murphy, James

2008-01-01T23:59:59.000Z

499

The Impact of Motor Vehicle Operation on Water Quality: A Premilinary Assessment  

E-Print Network (OSTI)

Institute), 1997. Used Motor Oil Collection and Recycling. Amillion gallons of used motor oil are improperly dischargedLike crude oil slicks, used motor oil can destroy aquatic

Nixon, Hillary; Saphores, Jean-Daniel

2003-01-01T23:59:59.000Z

500

A MULTI-COUNTRY ANALYSIS OF LIFECYCLE EMISSIONS FROM TRANSPORTATION FUELS AND MOTOR VEHICLES  

E-Print Network (OSTI)

Organization of Motor Vehicle Manufacturers, Paris, France,Organization of Motor Vehicle Manufacturers (2003) providesOrganization of Motor Vehicle Manufacturers. Because of

Delucchi, Mark

2005-01-01T23:59:59.000Z