Powered by Deep Web Technologies
Note: This page contains sample records for the topic "incandescent compact fluorescent" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Potential Environmental Impacts from the Metals in Incandescent, Compact Fluorescent Lamp (CFL), and Light-Emitting Diode (LED)  

E-Print Network [OSTI]

the lighting products are to be categorized as hazardous waste under existing U.S. federal and California state in lighting products without compromising their performance and useful lifespan. INTRODUCTION The U.S. Energy to increase energy efficiency for general lighting. Therefore, consumers are replacing incandescent light

Short, Daniel

2

Compact fluorescent lamp applications in luxury hotels  

SciTech Connect (OSTI)

Over the past several years, consumers, lighting designers, and energy conservationists have paid increasing attention to the special characteristics of compact fluorescent lamps (CFLs). CFLs can typically be used to replace incandescent lamps of three to four times their own wattage, and their color rendering indices (CRIs)-80 to 85-make them virtually indistinguishable from incandescents. The typical 10,0000-hour life of a CFL often makes savings in labor its most desirable feature when compared to a shorter-lived incandescent lamp.

Gilleskie, R.J.

1996-01-01T23:59:59.000Z

3

Thermally efficient compact fluorescent fixture systems  

SciTech Connect (OSTI)

Compact fluorescent lamps that can be inserted into conventional light fixtures are rapidly gaining acceptance as both a viable retrofit and new design approach to reducing lighting loads. Ideally, the compact fluorescent lamp should have the same light output as the incandescent lamp it replaces, but overheating inside typically small enclosed fixtures can reduce lumen output and hence lighting fixture efficiency by 15 to 20 percent. Fortunately, simple fixture modifications can erase this efficiency penalty, so that the full efficiency benefit of replacing incandescent lamps with fluorescent lamps can be realized. The paper describes such modifications and presents experimental data documenting the potential efficiency enhancement associated with thermal control systems. 4 refs., 7 figs.

Siminovitch, M.J.; Rubinstein, F.M.; Packer, M.

1991-04-01T23:59:59.000Z

4

Perceptions of compact fluorescent lamps in the residential market  

SciTech Connect (OSTI)

Compact fluorescent lamps offer significant energy savings over other forms of residential lighting and last up to 10 times longer than conventional incandescent bulbs. In order to better understand existing barriers to acceptance and future opportunities for growth of compact fluorescent lighting in the residential retrofit sector, a three stage research project was designed and conducted by MACRO Consulting, Inc. Assessment of whether or not the benefits of compact fluorescent lamps are sufficient to overcome price resistance was one of the major purposes of this project. Residential customers were interviewed in focus group sessions to help determine key issues and motivating forces in the lighting/energy saving/cost saving equation. Residential customers in 5 major market areas were contacted by telephone, and data about their awareness, knowledge and use of compact fluorescent lighting were collected. These customers also participated in an attribute rating exercise in which compact fluorescent lamps were compared with fluorescent tubes and incandescent bulbs on a series of product attributes. A price elasticity exercise was also conducted. Teleconferences with retailers of compact fluorescent lamps were conducted in order to explore their knowledge of and attitudes towards compact fluorescent lamps. Customers agree that energy savings and longer life are both positive attributes for residential lighting products, but they are not yet ready to make the switch away from inexpensive, versatile and readily available incandescent bulbs to compact fluorescent lamps. Compact fluorescent lamps are rated poorly (even by satisfied'' users) on each of seven positive attributes of home lighting. Major barriers to increased use of compact fluorescent lamps include price, convenience, and performance. Prices above $10 are considered outrageous''. Product improvements are needed for appearance, light output and versatility.

Weiner, J.; Campbell, C.J. (Macro Consulting, Inc., Mountain View, CA (United States))

1992-07-01T23:59:59.000Z

5

Energy-efficient compact screw-in fluorescent lamp. Final report  

SciTech Connect (OSTI)

A compact fluorescent lamp has been designed and constructed which can replace an incandescent lamp. The lamp is slightly larger than a standard lamp (8 3/4 in. x 3 1/4 in.), but is designed to fit a majority of portable lamp applications. This version, with a core-coil ballast, results in a system efficacy of 54 lumens per watt, with a light output of more than 1800 lumens. This compares favorably with a 100-watt incandescent (17.5 lumens per watt and 1750 lumens light output). The color temperature of 3000/sup 0/K is compatible with an incandescent lamp (2800/sup 0/K). The color rendition index (CRI) is 84. With a solid-state ballast, the efficacy and light output could be increased by 20% (65 l/w, 2200 lumens) and could provide a direct replacement for a three-way, 150-watt incandescent lamp (15 l/w, 2200 lumens).

Morton, E.W.

1982-11-01T23:59:59.000Z

6

A Bright Idea: New Efficiency Standards for Incandescent and...  

Broader source: Energy.gov (indexed) [DOE]

A Bright Idea: New Efficiency Standards for Incandescent and Fluorescent Lights A Bright Idea: New Efficiency Standards for Incandescent and Fluorescent Lights July 21, 2009 -...

7

The effects of supply harmonics on the performance of compact fluorescent lamps  

SciTech Connect (OSTI)

This paper describes a performance evaluation of ten compact fluorescent lighting systems operated with sinusoidal and distorted voltage waveform conditions. The lamps were either provided with an electronic ballast, a magnetic core ballast or a magnetic core ballast with a power factor correction circuit. The test results show that the electrical performance of the compact fluorescent lamps for both sinusoidal and distorted voltage waveform operation is related to the different types of ballast used. The cost of operation of these compact fluorescent lamps was calculated and compared to the cost of a conventional 60 W incandescent lamp.

Arseneau, R.; Ouellette, M.

1993-04-01T23:59:59.000Z

8

2014-04-11 Issuance: Energy Conservation Standards for General Service Fluorescent Lamps and Incandescent Reflector Lamps; Notice of Proposed Rulemaking  

Broader source: Energy.gov [DOE]

This document is a pre-publication Federal Register notice of proposed rulemaking regarding energy conservation standards for general service fluorescent lamps and incandescent reflectors lamps, as issued by the Assistant Secretary for Energy Efficiency and Renewable Energy on April 11, 2014.

9

Covered Product Category: Compact Fluorescent Lamps  

Broader source: Energy.gov [DOE]

FEMP provides acquisition guidance across a variety of product categories, including compact fluorescent lamps (CFLs), which are an ENERGY STAR-qualified product category.

10

Compact Fluorescent Plug-In Ballast-in-a-Socket  

SciTech Connect (OSTI)

The primary goal of this program was to develop a ballast system for plug-in CFLs (compact fluorescent lamps) that will directly replace standard metal shell, medium base incandescent lampholders (such as Levition No. 6098) for use with portable lamp fixtures, such as floor, table and desk lamps. A secondary goal was to identify a plug-in CFL that is optimized for use with this ballast. This Plug-in CFL Ballastin-a-Socket system will allow fixture manufacturers to easily manufacture CFL-based high-efficacy portable fixtures that provide residential and commercial consumers with attractive, cost-effective, and energy-efficient fixtures for use wherever portable incandescent fixtures are used today. The advantages of this proposed system over existing CFL solutions are that the fixtures can only be used with high-efficacy CFLs, and they will be more attractive and will have lower life-cycle costs than screw-in or adapter-based CFL retrofit solutions. These features should greatly increase the penetration of CFL's into the North American market. Our work has shown that using integrated circuits it is quite feasible to produce a lamp-fixture ballast of a size comparable to the current Edison-screw 3-way incandescent fixtures. As for price points for BIAS-based fixtures, end-users polled by the Lighting Research Institute at RPI indicated that they would pay as much as an additional $10 for a lamp containing such a ballast. The ballast has been optimized to run with a 26 W amalgam triple biax lamp in the base-down position, yet can accept non-amalgam versions of the lamp. With a few part alterations, the ballast can be produced to support 32 W lamps as well. The ballast uses GE's existing L-Comp[1] power topology in the circuit so that the integrated circuit design would be a design that could possibly be used by other CFL and EFL products with minor modifications. This gives added value by reducing cost and size of not only the BIAS, but also possibly other integral CFL and future dimmable integral and plug-in versions of the EFL products.

Rebecca Voelker

2001-12-21T23:59:59.000Z

11

Max Tech and Beyond: Fluorescent Lamps  

E-Print Network [OSTI]

Fluorescent Lamps and Incandescent Reflector Lamps; Finalmany end- use applications. Incandescent Outdoor Stationaryof color compared with the incandescent reference source is

Scholand, Michael

2012-01-01T23:59:59.000Z

12

Conservation Potential of Compact Fluorescent Lamps in India and Brazil  

E-Print Network [OSTI]

38 TWh, 10% of which was for incandescent lighting (Fig. 3).The electricity consumed in incandescent lighting can be300 and 400 million incandescent lamps in the country. Let

Gadgil, A.J.

2008-01-01T23:59:59.000Z

13

Conservation Potential of Compact Fluorescent Lamps in India and Brazil  

E-Print Network [OSTI]

also additional benefits from avoided costs of environmentalpremium for India)) - (avoided annual cost of incandescents)electricity) + (avoided annual cost of incandescents) - (

Gadgil, A.J.

2008-01-01T23:59:59.000Z

14

Photonically Engineered Incandescent Emitter  

DOE Patents [OSTI]

A photonically engineered incandescence is disclosed. The emitter materials and photonic crystal structure can be chosen to modify or suppress thermal radiation above a cutoff wavelength, causing the emitter to selectively emit in the visible and near-infrared portions of the spectrum. An efficient incandescent lamp is enabled thereby. A method for fabricating a three-dimensional photonic crystal of a structural material, suitable for the incandescent emitter, is also disclosed.

Gee, James M. (Albuquerque, NM); Lin, Shawn-Yu (Albuquerque, NM); Fleming, James G. (Albuquerque, NM); Moreno, James B. (Albuquerque, NM)

2005-03-22T23:59:59.000Z

15

Optimized Magnetic Components Improve Efficiency of Compact Fluorescent Lamps  

E-Print Network [OSTI]

xtures (designed for incandescent bulbs) has allowed residential and small commercial electric customers of incandescent lamps and last 10 times longer [1]. High-frequency electronic ballasts are used to power CFLs

16

High efficiency incandescent lighting  

DOE Patents [OSTI]

Incandescent lighting structure. The structure includes a thermal emitter that can, but does not have to, include a first photonic crystal on its surface to tailor thermal emission coupled to, in a high-view-factor geometry, a second photonic filter selected to reflect infrared radiation back to the emitter while passing visible light. This structure is highly efficient as compared to standard incandescent light bulbs.

Bermel, Peter; Ilic, Ognjen; Chan, Walker R.; Musabeyoglu, Ahmet; Cukierman, Aviv Ruben; Harradon, Michael Robert; Celanovic, Ivan; Soljacic, Marin

2014-09-02T23:59:59.000Z

17

Energy-efficient incandescent lamp: Final report  

E-Print Network [OSTI]

of Energy Conserving Incandescent Lamps", J . Brett, R.July 1981. "Filaments for Incandescent Lamps with Radiation20-22 "Energy Saving Incandescent Lamps with Infrared

Verderber, R.

2010-01-01T23:59:59.000Z

18

The Hazards of Use and Disposal of Compact Fluorescent Bulbs Compact fluorescent lights (aka. CFLs) work by exciting a phosphorous coating within the tube to emit  

E-Print Network [OSTI]

The Hazards of Use and Disposal of Compact Fluorescent Bulbs Compact fluorescent lights (aka. CFLs FLUORESCENT BULB? Because there is such a small amount of mercury in CFLs, the greatest hazard exposure the bulb to be an efficient light source. By comparison, older home thermometers contain 500 milligrams

Maroncelli, Mark

19

The incandescent disposal system  

SciTech Connect (OSTI)

The electrotechnology device being introduced to the low-level waste market is an Incandescent Disposal System (IDS) for volume reduction and vitrification. The process changes the composition of the waste material, usually long molecular chains, into simple molecules and elements. It renders the volume of low-level wastes to a manageable solid vitrified residue, carbon black, and a water discharge. The solid material, which has been vitrified if silica is introduced into the waste stream, is an ideal inert filler. The carbon black is non-leaching and is readily available for vitrification as it comes out of the IDS.

Smith, R.G.

1996-03-01T23:59:59.000Z

20

Cost effectiveness of long life incandescent lamps and energy buttons  

SciTech Connect (OSTI)

Long-life replacement lamps for the incandescent lamp have been evaluated with regard to their cost effectiveness. The replacements include the use of energy buttons that extend lamp life as well as an adaptive fluorescent circline lamp that will fit into existing incandescent lamp sockets. The initial, operating, and replacement costs for one million lumen hours are determined for each lamp system. It is found that the most important component lighting cost is the operating cost. Using lamps that are less efficient or devices that cause lamps to operate less efficiently are not cost-effective. The adaptive fluorescent circline lamp, even at an initial unit cost of $20.00, is the most cost-effective source of illumination compared to the incandescent lamp and lamp systems examined.

Verderber, R.; Morse, O.

1980-04-07T23:59:59.000Z

Note: This page contains sample records for the topic "incandescent compact fluorescent" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Energy Savings and NOx Emissions Reduction Potential from the 2012 Federal Legislation to Phase Out Incandescent Lamps in Texas  

E-Print Network [OSTI]

Lamps in Texas Description Value Reference Total Housing Units in Texas in 2013: 10,204,056 Real Estate Center, Texas A&M University3, U.S. Census Bureau4 5 Average Lighting Electricity Usage per House: 1,946 kWh/yr NREL Building America Program6... Savings in Texas: 10,424,973 MWh/yr OSD CFL Savings in Texas: 28,562 MWh/day By 2013, it is estimated that total savings of 10,424,973 MWh/yr would be achieved from replacing incandescent lamps with compact fluorescent lamps (CFL) in residential...

Liu, Zi; Baltazar, Juan Carlos; Haberl, Jeff; Soman, Rohit

22

Underwater Lighting by Submerged Lasers and Incandescent Sources  

E-Print Network [OSTI]

and collimated underwater incandescent projector. The laser-collimated underwater incandescent projector used for beamBY SUBMERGED LASERS and Incandescent Sources DESCRIPTIVE

Duntley, Seibert Q

1971-01-01T23:59:59.000Z

23

,,,"Incandescent","Standard Fluorescent","Compact Fluorescent","High-Intensity Discharge","Halogen"  

U.S. Energy Information Administration (EIA) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia:FAQProved Reserves, Reserves Changes, and Production" ,"Click worksheet name or tabUpcoming8. Energy38.

24

,,,"Incandescent","Standard Fluorescent","Compact Fluorescent","High-Intensity Discharge","Halogen"  

U.S. Energy Information Administration (EIA) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data CenterFranconia, Virginia:FAQProved Reserves, Reserves Changes, and Production" ,"Click worksheet name or tabUpcoming8.

25

Mercury Lamps Recycling Fluorescent light-tubes, compact fluorescent bulbs, mercury and sodium vapor lamps, ultraviolet and  

E-Print Network [OSTI]

Mercury Lamps Recycling Fluorescent light-tubes, compact fluorescent bulbs, mercury and sodium vapor lamps, ultraviolet and HID (high-intensity discharge) lamps and all other mercury containing labeled for shipment to a recycling plant for mercury, glass and aluminum recovery. The beneficial re

Baker, Chris I.

26

Conservation potential of compact fluorescent lamps in India and Brazil  

SciTech Connect (OSTI)

We evaluate the conservation potential of compact fluorescent lamps (CFLs) for managing the rapidly increasing electrical energy and peak demand in India and Brazil. Using very conservative assumptions, we find that the cost of conserved energy using 16 W CFLs is 4 and 6 times less than the long range marginal cost of electricity for the two countries. The cost of avoided peak installed capacity is 6 and 9.5 times less than the cost of new installed capacity for India and Brazil. The analysis is undertaken from the three separate perspectives of the national economies, the consumers, and the utilities. We find that because residential electricity is subsidized, the consumers have little or no incentive to purchase and install the CFLs, unless they too are subsidized. However, the benefits of CFL installation to the utility are so large that subsidizing them is a paying proposition for the utility are so large that subsidizing them is a paying proposition for the utility in almost all cases. As an illustration of a gradual introduction strategy for CFLs, we calculate a scenario where national savings of the order of US $1.2 million per day for India and US $2.5 million per day for Brazil are reached in 10 years by a small and gradual transfer of subsidy from residential electricity to CFLs. We then explore the barriers to immediate large scale introduction of these lamps in the two countries. Specific technical and marketing problems are identified and discussed, which would require solution before such an introduction can be attempted. Lastly, we discuss the range of policy instruments, in addition to a subsidy scheme, that can be used for promoting the diffusion of these lamps in the domestic and commercial sector. 47 refs., 15 figs., 2 tabs.

Gadgil, A.; Martino Jannuzzi, G. de (Lawrence Berkeley Lab., CA (USA); Universidade Estadual de Campinas, SP (Brazil). Faculdade de Engenharia)

1989-07-01T23:59:59.000Z

27

COST EFFECTIVENESS OF LONG LIFE INCANDESCENT LAMPS AND ENERGY BUTTONS  

E-Print Network [OSTI]

as any 1ong-li incandescent lamp or system evaluated in thisEFFECTIVENESS OF LONG LIFE INCANDESCENT LAMPS AND ENERGYEFFECTIVENESS OF LONG LIFE INCANDESCENT LAMPS AND ENERGY

Verderber, Rudy

2013-01-01T23:59:59.000Z

28

General service incandescent lamp with improved efficiency  

SciTech Connect (OSTI)

A high efficiency general service incandescent lamp is disclosed. The disclosed improved general service incandescent lamp has an outer and an inner envelope. The inner envelope has a relatively small housing containing a halogen gas and a relatively high pressure efficient fill-gas and in which a low voltage filament is spatially disposed therein.

Berlec, I.

1985-06-18T23:59:59.000Z

29

Dual LED/incandescent security fixture  

DOE Patents [OSTI]

A dual LED and incandescent security lighting system uses a hybrid approach to LED illumination. It combines an ambient LED illuminator with a standard incandescent lamp on a motion control sensor. The LED illuminator will activate with the onset of darkness (daylight control) and typically remain on during the course of the night ("always on"). The LED illumination, typically amber, is sufficient to provide low to moderate level lighting coverage to the wall and ground area adjacent to and under the fixture. The incandescent lamp is integrated with a motion control circuit and sensor. When movement in the field of view is detected (after darkness), the incandescent lamp is switched on, providing an increased level of illumination to the area. Instead of an "always on" LED illuminator, the LEDs may also be switched off when the incandescent lamp is switched on.

Gauna, Kevin Wayne

2005-06-21T23:59:59.000Z

30

Convection venting lensed reflector-type compact fluorescent lamp system  

DOE Patents [OSTI]

Disclosed herein is a fluorescent lamp housing assembly capable of providing convection cooling to the lamp and the ballast. The lens of the present invention includes two distinct portions, a central portion and an apertured portion. The housing assembly further includes apertures so that air mass is able to freely move up through the assembly and out ventilation apertures. 12 figs.

Pelton, B.A.; Siminovitch, M.

1997-07-29T23:59:59.000Z

31

Visible Spectrum Incandescent Selective Emitter  

SciTech Connect (OSTI)

The purpose of the work performed was to demonstrate the feasibility of a novel bi-layer selective emitter. Selective emitters are incandescent radiant bodies with emissivities that are substantially larger in a selected part of the radiation spectrum, thereby significantly shifting their radiated spectral distribution from that of a blackbody radiating at the same temperature. The major research objectives involved answering the following questions: (1) What maximum VIS/NIR radiant power and emissivity ratios can be attained at 2650 K? (2) What is the observed emitter body life and how does its performance vary with time? (3) What are the design tradeoffs for a dual heating approach in which both an internally mounted heating coil and electrical resistance self-heating are used? (4) What are the quantitative improvements to be had from utilizing a bi-layer emitter body with a low emissivity inner layer and a partially transmissive outer layer? Two approaches to obtaining selective emissivity were investigated. The first was to utilize large optical scattering within an emitter material with a spectral optical absorption that is much greater within the visible spectrum than that within the NIR. With this approach, an optically thick emitter can radiate almost as if optically thin because essentially, scattering limits the distance below the surface from which significant amounts of internally generated radiation can emerge. The performance of thin emitters was also investigated (for optically thin emitters, spectral emissivity is proportional to spectral absorptivity). These emitters were fabricated from thin mono-layer emitter rods as well as from bi-layer rods with a thin emitter layer mounted on a substrate core. With an initially estimated energy efficiency of almost three times that of standard incandescent bulbs, a number of energy, economic and environmental benefits such as less energy use and cost, reduced CO{sub 2} emissions, and no mercury contamination was initially projected. The work performed provided answers to a number of important questions. The first is that, with the investigated approaches, the maximum sustained emitter efficiencies are about 1.5 times that of a standard incandescent bulb. This was seen to be the case for both thick and thin emitters, and for both mono-layer and bi-layer designs. While observed VIS/NIR ratios represent improvements over standard incandescent bulbs, it does not appear sufficient to overcome higher cost (i.e. up to five times that of the standard bulb) and ensure commercial success. Another result is that high temperatures (i.e. 2650 K) are routinely attainable without platinum electrodes. This is significant for reducing material costs. A novel dual heating arrangement and insulated electrodes were used to attain these temperatures. Another observed characteristic of the emitter was significant grain growth soon after attaining operating temperatures. This is an undesirable characteristic that results in substantially less optical scattering and spectral selectivity, and which significantly limits emitter efficiencies to the values reported. Further work is required to address this problem.

Sonsight Inc.

2004-04-30T23:59:59.000Z

32

Tungsten wire for incandescent lamps  

SciTech Connect (OSTI)

Tungsten wire for incandescent lamp filaments must operate at high temperatures and for long times. To meet these requirements, the grain morphology of the wire must be controlled to reduce the propensity for grain boundary sliding. The morphology is a function of the distribution of very small pockets of potassium in the wire and the mechanical processing from ingot to wire. The behavior of the filament is directly related to the grain morphology. This paper describes the mechanism by which the potassium is incorporated into and distributed in the ingot. The elongation and spheroidization of the bubbles during hot rolling and swaging is also examined and related to the grain morphology of wire. Some indications of the relationship between grain morphology and filament behavior are also given.

Walter, J.L.; Briant, C.L. (General Electric Corporate Research and Development, Schenectady, NY (USA))

1990-09-01T23:59:59.000Z

33

Compact fluorescent lamp using horizontal and vertical insulating septums and convective venting geometry  

DOE Patents [OSTI]

A novel design is described for a compact fluorescent lamp, including a lamp geometry which will increase light output and efficacy of the lamp in a base down operating position by providing horizontal and vertical insulating septums positioned in the ballast compartment of the lamp to provide a cooler coldspot. Selective convective venting provides additional cooling of the ballast compartment. 9 figs.

Siminovitch, M.

1998-02-10T23:59:59.000Z

34

Frequently Asked Questions Information on Compact Fluorescent Light Bulbs (CFLs) and Mercury  

E-Print Network [OSTI]

Frequently Asked Questions Information on Compact Fluorescent Light Bulbs (CFLs) and Mercury emissions equivalent to those of more than 800,000 cars. Do CFLs contain mercury? CFLs contain a very small amount of mercury sealed within the glass tubing ­ an average of 5 milligrams ­ about the amount

Jia, Songtao

35

Compact light source performance in recessed type luminaires  

SciTech Connect (OSTI)

Photometric comparisons were made with an indoor, recessed, type luminaire using incandescent, high intensity discharge and compact fluorescent lamps. The test results show substantial performance advantages, as expected, for the discharge light sources where the efficacy gains can be in the order for 400% even when including the ballast losses associated with the discharge lamps. The candlepower distribution patterns emerging from these luminaries are also different from those associated with the baseline incandescent lamps, and which are in some ways, even more desirable from a uniformity of illuminance perspective. A section on fluorescent lamp starting is also included which describes a system having excellent starting characteristics in terms of electrode starting temperature (RH/RC technique), proper operating frequency to minimize unwanted IR interactions, and satisfactory current crest factor values to help insure life performance.

Hammer, E.E.

1998-11-01T23:59:59.000Z

36

Comprehensive Pyrometry of Incandescent Multiwalled Carbon Nanotubes and Graphene in the Visible and Near Infrared  

E-Print Network [OSTI]

4.17 Image of incandescent tungsten ?to collect data from incandescent MWCNTs. An illustration ofand of Carbon at Incandescent Temper- atures, Physical

Singer, Scott

2012-01-01T23:59:59.000Z

37

Managing Your Energy: An ENERGY STAR(R) Guide for Identifying Energy Savings in Manufacturing Plants  

E-Print Network [OSTI]

fluorescent (CFL), and incandescent lights are typicallyhours) Applications Incandescent Task Halogen Task CFL TaskCenter of Wisconsin. Replace incandescent lamps with compact

Worrell, Ernst

2010-01-01T23:59:59.000Z

38

DOE Requires Manufacturer and Labeler to Cease Sale of Incandescent...  

Broader source: Energy.gov (indexed) [DOE]

Manufacturer and Labeler to Cease Sale of Incandescent Reflector Lamps DOE Requires Manufacturer and Labeler to Cease Sale of Incandescent Reflector Lamps June 24, 2010 - 2:40pm...

39

Compact Fluorescent Lighting in America: Lessons Learned on the Way to Market  

SciTech Connect (OSTI)

This report describes the history of compact fluorescent lamps (CFLs) in America. CFLs were introduced in the 1970s; however, it has taken more than 20 years for them to gain widespread recognition in the U.S. residential lighting market. This report reviews the development of CFLs, efforts to increase market acceptance of them, and barriers to that acceptance. Lessons to be learned from this study of CFLs are identified in hopes of assisting future market introduction efforts for other promising energy-efficient technologies. This report was prepared by the Pacific Northwest National Laboratory for the U.S. Department of Energys Office of Building Technologies, Emerging Technologies Program.

Sandahl, Linda J.; Gilbride, Theresa L.; Ledbetter, Marc R.; Steward, Heidi E.; Calwell, Chris

2006-05-22T23:59:59.000Z

40

Incandescent Lighting Basics | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "of EnergyEnergyENERGYWomentheATLANTA,Fermi NationalBusiness PlanPosting of| Department ofTheseIncandescent

Note: This page contains sample records for the topic "incandescent compact fluorescent" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

AN ANALYTICAL AND QUANTITATIVE ANALYSIS OF THE LASER-INDUCED INCANDESCENCE OF SOOT  

E-Print Network [OSTI]

AN ANALYTICAL AND QUANTITATIVE ANALYSIS OF THE LASER-INDUCED INCANDESCENCE OF SOOT A Thesis-INDUCED INCANDESCENCE OF SOOT Approved: _________________________ Jerry M. Seitzman, Chairman

Seitzman, Jerry M.

42

How Energy-Efficient Light Bulbs Compare with Traditional Incandescent...  

Broader source: Energy.gov (indexed) [DOE]

could save you about 50 per year in energy costs when you replace 15 traditional incandescent bulbs in your home. Energy-efficient light bulbs are available today and could save...

43

A Review of the Reflector Compact Fluorescent Lights Technology Procurement Program: Conclusions and Results  

SciTech Connect (OSTI)

This report describes a project sponsored by the U.S. Department of Energy (DOE) and implemented by the Pacific Northwest National Laboratory (PNNL), from 2000 to 2007 to improve the performance of reflector type (R-lamp) compact fluorescent lamps (CFLs) and increase their availability throughout the United States by means of a technology development and procurement strategy. In 2000, at the request of the U.S. Department of Energys Emerging Technologies Program and its predecessors, the Pacific Northwest National Laboratory undertook a technology procurement seeking R-CFLs that were specifically designed for use in ICAT recessed can fixtures and that met other minimum performance criteria including minimum light output and size restrictions (to ensure they fit in standard residential recessed cans). The technology procurement included two phases. In Phase I, requests for proposals (RFPs) were issued in October 2002 and five manufacturers responded with 12 lamp models. Eight of these models met the minimum requirements and passed the 6-hour short-term test in a simulated ICAT environment. These eight models were subjected to long-term tests of 6,000 or more hours in a simulated ICAT environment. Three of these models passed the short- and long-term tests and were promoted through the program website (www.pnl.gov/rlamps), press releases, and fliers. To increase the number of qualifying models, a second RFP was issued in June 2005. In April 2007, DOE announced that 16 reflector CFL (R-CFL) models by four manufacturers had met all the minimum requirements of Phase 2 of the R-CFL Technology Innovation Competition. PNNL developed both the criteria and the test apparatus design for Elevated Temperature Life Testing (ETLT), which has been included by DOE in its draft ENERGY STAR specifications for the reflector category of CFLs. PNNL promoted the winning lamps through a program website, press releases, and fliers as well as through program partners. PNNL also helped engage distributors including Costco, the Home Depot, Bonneville Power Administration, and utility organizations.

Sandahl, Linda J.; Gilbride, Theresa L.; Ledbetter, Marc R.; McCullough, Jeffrey J.

2008-05-19T23:59:59.000Z

44

Compact  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation Proposed New SubstationCleanCommunity Involvement and Making aCompact soft x-ray multichord

45

Assessment of soot particle vaporization effects during laser-induced incandescence with  

E-Print Network [OSTI]

Assessment of soot particle vaporization effects during laser-induced incandescence with time-induced incandescence (LII) has been successfully used for soot volume fraction and particle size measurements

Hahn, David W.

46

DSM Electricity Savings Potential in the Buildings Sector in APP Countries  

E-Print Network [OSTI]

150 million compact fluorescent light bulbs in 2010. (ChinaCleaners Incandescent Bulbs Fluorescent Lamps Ballasts forincandescent bulbs with compact fluorescent lamps. Consumers

McNeil, MIchael

2011-01-01T23:59:59.000Z

47

Metallic photonic-band-gap filament architectures for optimized incandescent lighting Sajeev John and Rongzhou Wang  

E-Print Network [OSTI]

Metallic photonic-band-gap filament architectures for optimized incandescent lighting Sajeev John occur 3,4 . Tra- ditionally incandescent lighting filaments, despite being driven from equilibrium the blackbody spectrum. This suggests the pos- sibility of higher efficiency incandescent lighting, through

John, Sajeev

48

Molecular Dynamics Simulations of Laser Induced Incandescence Dr. Adri van Duin  

E-Print Network [OSTI]

Molecular Dynamics Simulations of Laser Induced Incandescence (LII) Dr. Adri van Duin Associate of Engineering. Laser Induced Incandescence (LII) is a popular method to estimate the properties of soot. Molecular Dynamics Simulations of Laser-Induced Incandescence of Soot Using an Extended ReaxFF Reactive

Bjørnstad, Ottar Nordal

49

L'EMISSION ELECTRIQUE DU PLATINE INCANDESCENT DANS UNE ATMOSPHRE D'IODE  

E-Print Network [OSTI]

L'EMISSION ELECTRIQUE DU PLATINE INCANDESCENT DANS UNE ATMOSPH?RE D'IODE par M. S. KALANDYK influence devient nulle aux températures de chauffage élevées. 3. Pour une faible incandescence du platine approximativement linéaire; aux fortes incandescences, cette variation offre un caractère beaucoup plus compliqué. 1

Paris-Sud XI, Université de

50

Introduction The Sun is a mass of incandescent gas  

E-Print Network [OSTI]

Chapter 1 Introduction The Sun is a mass of incandescent gas A gigantic nuclear furnace Building that our bodies contain atoms that, like most elements and their isotopes in the Solar System, were part of the molecular cloud from which the Solar System condensed, and were trapped in primitive

Nittler, Larry R.

51

J.-A. FLEMING. 2014 On the characteristic curves and surfaces of incandescence lamps (Courbes caractristiques des lampes incandescence) ; Phil. Mag.,  

E-Print Network [OSTI]

80 J.-A. FLEMING. 2014 On the characteristic curves and surfaces of incandescence lamps (Courbes caractéristiques des lampes à incandescence) ; Phil. Mag., 5e série, t. XIX, p. 368; I885. L'auteur étudie les résistance correspondant à la force électromotrice vo à laquelle l'incandescence commence à se produire, et r

Paris-Sud XI, Université de

52

Table Set-up with Materials near Lamp Stand (below) Target Audience: Parents of elementary school students (grades 3-6) and Middle and High School Students  

E-Print Network [OSTI]

spectrum with different light sources; compact fluorescent, LED, incandescent. 5. Discuss light bulb. Observe difference of color spectrum with different light sources; compact fluorescent, LED, incandescent type of bulb at different horizontal level. Electromagnetic Spectrum handouts that includes spectrum

Linhardt, Robert J.

53

L'MISSION LECTRIQUE DU PLATINE INCANDESCENT DANS UNE ATMOSPHRE D'IODE  

E-Print Network [OSTI]

L'?MISSION ?LECTRIQUE DU PLATINE INCANDESCENT DANS UNE ATMOSPH?RE D'IODE par M. PIERRE JEZ],du platine incandescent ~dans une atmosphère d'iode en fonction : 1, de la température ; 2, du temps; 3, de électrodes, d'un grillage métallique pour éviter les influences extérieures. L'incandescence des électrodes s

Paris-Sud XI, Université de

54

LE RAYONNEMENT DES MANCHONS A INCANDESCENCE ; Par M. H. RUBENS1).  

E-Print Network [OSTI]

306 LE RAYONNEMENT DES MANCHONS A INCANDESCENCE ; Par M. H. RUBENS1). 1. - INTRODUCTION. Les remarquables propriétés du manchon à incandescence Auer ont dès l'origine excité au plus haut point l été entreprises par Langley pour la lampe à incandescence au pétrole avec l'aide de ses bolomètres

Paris-Sud XI, Université de

55

PROCD RAPIDE POUR LA PHOTOMTRIE DES BECS A INCANDESCENCE PAR LE GAZ (1) ;  

E-Print Network [OSTI]

469 PROC?D? RAPIDE POUR LA PHOTOM?TRIE DES BECS A INCANDESCENCE PAR LE GAZ (1) ; Par P. LAURIOL. Les essais des becs à incandescence par le gaz destinés à l'éclai- rage public comportent un très pendant une série de mesures. On emploie une lampe à incandescence électrique dont on #12;471 maintint la

Paris-Sud XI, Université de

56

MISSION CATHODIQUE A L'INTRIEUR DES LAMPES A INCANDESCENCE ; par M. L. HOULLEVIGUE (1).  

E-Print Network [OSTI]

523 ?MISSION CATHODIQUE A L'INT?RIEUR DES LAMPES A INCANDESCENCE ; par M. L. HOULLEVIGUE (1). I. Lorsqu'on survolte fortement une lampe à incandescence à filament de charbon, par exemple en mettant sous incandescent. ' , Fic.. 1. Tous ces effets peuvent être attribués, en première analyse, aux électrons émanés du

Boyer, Edmond

57

EA-1911: Energy Conservation Standards for Certain Reflector, Elliptical Reflector, and Bulged Reflector Incandescent Lamps  

Broader source: Energy.gov [DOE]

This EA will evaluate the environmental impacts of a proposal to amend energy conservation standards for Certain Reflector, Elliptical Reflector, and Bulged Reflector Incandescent Lamps.

58

How to upgrade your incandescent light bulbs Many people are choosing replacements for their standard incandescent light bulbs to save money or energy, because they've heard of new LED  

E-Print Network [OSTI]

How to upgrade your incandescent light bulbs Many people are choosing replacements for their standard incandescent light bulbs to save money or energy, because they've heard of new LED options, or in anticipation of the phase-out of standard incandescent bulbs in the U.S. starting in 2012. If you've shopped

Bystroff, Chris

59

Operating temperatures for a convectively cooled recessed incandescent light fixture  

SciTech Connect (OSTI)

Test results are given for the operation of a recessed incandescent light fixture intended for residential use. The fixture is labeled for use in direct contact with attic thermal insulation. Temperature control of the powered fixture is provided by convective heat transfer from the ceiling side of the fixture. The fixture was operated at power levels up to two times the rated power of 75 watts and under thermal insulations up to R-40. In all operating configurations tested the fixture surface in contact with attic insulation was found to be less than 175/sup 0/C. The observed surface temperatures are judged to be safe for operation in contact with loose-fill or batt-type insulations. It was observed that the power leads inside one fixture configuration are exposed to temperatures as high as 168/sup 0/C. The electrical insulation could, therefore, have a limited life. The properties of the internal fixture wiring were not, however, studied in detail.

Yarbrough, D.W.; Toor, I.

1980-12-01T23:59:59.000Z

60

Apparatus to facilitate lengthening the life of incandescent lamps  

SciTech Connect (OSTI)

An energizing circuit is described for an incandescent bulb comprising a transformer having a primary winding connectable to an AC mains source and first and second secondary windings for producing first and second voltages. The first secondary winding is connected to an input of a first full-wave rectifier means and the second secondary winding is connected to an input of a second full-wave rectifier means, the full-wave rectifier means having outputs connected in parallel across the bulb. The first voltage is sufficient to fully illuminate the bulb and the second voltage is sufficient to maintain the bulb warm but with little or no light output, a first switch being connected between the first secondary winding and the first rectifier means whereby, when the first switch is open, the bulb is energized solely by the second voltage.

Spissinger, F.H.

1987-03-17T23:59:59.000Z

Note: This page contains sample records for the topic "incandescent compact fluorescent" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

L'MISSION LECTRIQUE DU TUNGSTNE INCANDESCENT DANS UNE ATMOSPHRE D'IODE.  

E-Print Network [OSTI]

L'?MISSION ?LECTRIQUE DU TUNGST?NE INCANDESCENT DANS UNE ATMOSPH?RE D'IODE. par S. KALANDYK'émission négative du tungstène; l'influence de l'iode est prépondérante aux basses températures d'incandescence 3. L vapeur d'iode augmente l'émis sion électrique négative du platine incandescent. L'influence de l'iode se

Paris-Sud XI, Université de

62

NEXT GENERATION ENERGY EFFICIENT FLUORESCENT LIGHTING PRODUCT  

SciTech Connect (OSTI)

This is the Final Report of the Next-Generation Energy Efficient Fluorescent Lighting Products program, Department of Energy (DOE). The overall goal of this three-year program was to develop novel phosphors to improve the color rendition and efficiency of compact and linear fluorescent lamps. The prime technical approach was the development of quantum-splitting phosphor (QSP) to further increase the efficiency of conventional linear fluorescent lamps and the development of new high color rendering phosphor blends for compact fluorescent lamps (CFLs) as potential replacements for the energy-hungry and short-lived incandescent lamps in market segments that demand high color rendering light sources. We determined early in the project that the previously developed oxide QSP, SrAl{sub 12}O{sub 19}:Pr{sup 3+}, did not exhibit an quantum efficiency higher than unity under excitation by 185 nm radiation, and we therefore worked to determine the physical reasons for this observation. From our investigations we concluded that the achievement of quantum efficiency exceeding unity in SrAl{sub 12}O{sub 19}:Pr{sup 3+} was not possible due to interaction of the Pr{sup 3+} 5d level with the conduction band of the solid. The interaction which gives rise to an additional nonradiative decay path for the excitation energy is responsible for the low quantum efficiency of the phosphor. Our work has led to the development of a novel spectroscopic method for determining photoionzation threshold of luminescent centers in solids. This has resulted in further quantification of the requirements for host phosphor lattice materials to optimize quantum efficiency. Because of the low quantum efficiency of the QSP, we were unable to demonstrate a linear fluorescent lamp with overall performance exceeding that of existing mercury-based fluorescent lamps. Our work on the high color rendering CFLs has been very successful. We have demonstrated CFLs that satisfies the EnergyStar requirement with color rendering index (CRI) greater than 90; the CRI of current commercial CFLs are in the low 80s. In this report we summarize the technical work completed under the Program, summarize our findings about the performance limits of the various technologies we investigated, and outline promising paths for future work.

Alok Srivastava; Anant Setlur

2003-04-01T23:59:59.000Z

63

ECE 466: LED Lighting Systems -Incandescent lightings rise and  

E-Print Network [OSTI]

versus cost - Power Electronic Drives for CFL and LED light sources to achieve dimmable operation - Basic electric AC and DC circuits at Sophomore level or equivalents Absolutes Lighting System Requirements index as a metric of a light source - Power Electronic Energy sources driving light sources in a compact

Schumacher, Russ

64

Funding Sustainable Initiatives: Should Williams Implement a Revolving Loan Fund?  

E-Print Network [OSTI]

to replace its incandescent light bulbs with more efficient compact fluorescent (CFL) light bulbs. These light bulbs use 2/3 less energy than #12;Terra 4 standard incandescent bulbs, but they are more

Aalberts, Daniel P.

65

Geaux Green: GREEN GUIDE  

E-Print Network [OSTI]

account. Make a switch Replace incandescent light bulbs with energy-efficient compact fluorescent lights. Remember: You should always turn your lights off regardless if they are incandescent bulbs or CFLs. Take

Harms, Kyle E.

66

U.S. Energy Information Administration (EIA) - Sector  

Gasoline and Diesel Fuel Update (EIA)

replacement of incandescent bulbs with more efficient compact fluorescent lighting and light-emitting diode (LED) lamps. Among electric end-use services in the residential...

67

Educators: Are You Ready to Teach Energy Literacy? Join our August...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

pedal for power and experience the difference in physical effort necessary to power incandescent, compact fluorescent, and LED lighting. This lesson highlighted Energy Principle 4,...

68

--No Title--  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

alike can also reduce power demand, and thus carbon emissions, by replacing the incandescent bulbs in their homes with energy-saving compact fluorescent bulbs. That's a handy...

69

--No Title--  

Broader source: Energy.gov (indexed) [DOE]

out fixtures to accommodate compact fluorescent bulbs instead of relying on incandescent bulbs. Energy Efficiency and Conservation Block Grants Native Village of Stevens...

70

Energy Efficiency and Conservation Block Grant Program  

Broader source: Energy.gov (indexed) [DOE]

retrofits throughout the Village. These lighting retrofits would involve upgrading incandescent light fixtures to those that will accommodate compact fluorescent bulbs. In...

71

CX-000133: Categorical Exclusion Determination | Department of...  

Broader source: Energy.gov (indexed) [DOE]

the funding permits. Residences for the retrofits will be selected based on need. Incandescent bulbs would be replaced with compact fluorescent bulbs. Power consumption would be...

72

CX-000136: Categorical Exclusion Determination | Department of...  

Broader source: Energy.gov (indexed) [DOE]

retrofits for bathrooms of 42 residences. These retrofits would involve upgrading incandescent light fixtures to those that will accommodate compact fluorescent bulbs. It is...

73

--No Title--  

Broader source: Energy.gov (indexed) [DOE]

retrofits for bathrooms of 42 residences. These retrofits would involve upgrading incandescent light fixtures to those that will accommodate compact fluorescent bulbs. It is...

74

CX-000137: Categorical Exclusion Determination | Department of...  

Broader source: Energy.gov (indexed) [DOE]

out fixtures to accommodate compact fluorescent bulbs instead of relying on incandescent bulbs. DOCUMENT(S) AVAILABLE FOR DOWNLOAD CX-000137.pdf More Documents &...

75

--No Title--  

Broader source: Energy.gov (indexed) [DOE]

the funding permits. Residences for the retrofits will be selected based on need. Incandescent bulbs would be replaced with compact fluorescent bulbs. Power consumption would be...

76

CX-003246: Categorical Exclusion Determination | Department of...  

Broader source: Energy.gov (indexed) [DOE]

retrofits throughout the Village. These lighting retrofits would involve upgrading incandescent light fixtures to those that will accommodate compact fluorescent bulbs. In...

77

Creating markets for new products to replace incandescent lamps: The international experience  

SciTech Connect (OSTI)

Since the summer of 1995, several organizations have been in pursuit of what many consider the Holy Grail of lighting technology--a low-cost, drop-in, energy-efficient replacement for the incandescent lamp. This paper summarizes the international experience in attempting to catalyze the commercialization of a mass-market, replacement product that could have major impact on residential lighting energy consumption in US and EU homes. The technology procurement effort was originally spearheaded by US Federal Government through a loose collaboration between the Department of Defense (DoD), the Environmental Protection Agency (EPA) and the Department of Energy (DOE). The DoD agreed to serve as the anchor buyer for a low-cost, drop-in replacement product for standard-sized light bulbs that provide at least 30 percent energy savings compared to traditional incandescent lamps. In parallel to the US effort, the International Energy Agency launched a co-operative technology procurement effort by assembling large buyers' groups in Finland, the Netherlands, Sweden, and the United Kingdom to pull a similar efficient lighting product into the European market. The lukewarm response from lamp manufacturers to these two technology procurement efforts illustrates the challenges of transforming residential lighting from incandescent to efficient lighting.

Rubinstein, F.; Borg, N.; Horowitz, N.; Narel, T.; Morehouse, E.T. Jr.

1998-07-01T23:59:59.000Z

78

EK101 Engineering Light Project: Evaluate Residential Lighting  

E-Print Network [OSTI]

for residential lighting (LED, Compact Fluorescent, Incandescent). Develop a plan of experiments to be conducted, CF, and Incandescent bulbs for the past ten years. (try the wayback time machine if other sources fail). Discuss the key challenges associated with a transition from incandescent lighting

Bifano, Thomas

79

A theoretical study of the incandescent filament lamp performance under voltage flicker  

SciTech Connect (OSTI)

Incandescent filament lamp flicker, produced by voltage fluctuation, is a power quality problem that caused engineering concern since the onset of electrical illumination technology. The flicker phenomenon was analyzed and explained in early studies. Standards dealing with acceptable flicker levels are well known, nevertheless, today the discussion about flicker continues to be a top priority topic due to the fact that steady-state and transient voltage waveform distortion is a growing problem in low and medium voltage systems. In many situations voltage flicker is caused by subharmonics and interharmonics of voltage. Cycloconverters, welders and arc furnaces, eccentrically operating tools and integral cycle controlled power equipment are notorious for producing voltage flicker. The goal of this paper is to provide solid mathematical basis for the analytical modeling of incandescent filament lamp flicker when the voltage is nonsinusoidal. A mathematical model that enables the evaluation of the luminous flux modulation caused by noninteger harmonics (subharmonics and interharmonics) is presented. Three situations are detailed: square-wave voltage modulation, sinusoidal modulation and the case of noninteger harmonics with nearly contiguous frequencies.

Peretto, L. [Univ. of Bologna (Italy)] [Univ. of Bologna (Italy); Emanuel, A.E. [Worcester Polytechnic Inst., MA (United States)] [Worcester Polytechnic Inst., MA (United States)

1997-01-01T23:59:59.000Z

80

Design and Predictive Control of a Net Zero Energy Home  

E-Print Network [OSTI]

the same amount of light as traditional incandescent bulbs with less energy. Incandescent bulbs are inherently inefficient as most of the energy they consume goes towards heat generation. Compact fluorescent (CFL) and light emitting diode (LED) bulbs... as heat [1]. Compact fluorescent lamps (CFLs) and Light Emitting Diodes (LEDs) were analyzed in comparison with incandescent lamps. To determine the most energy efficient bulb, energy consumption for each type of bulb is needed. To do this, the amount...

Morelli, F.; Abbarno, N.; Boese, E.; Bullock, J.; Carter, B.; Edwards, R.; Lapite, O.; Mann, D.; Mulvihill, C.; Purcell, E.; Stein, M. IV; Rasmussen, B. P.

2013-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "incandescent compact fluorescent" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Linings with optimum heat-emission surfaces for cars receiving and transporting incandescent coke  

SciTech Connect (OSTI)

The least reliable components of the cars which receive and transport incandescent coke are the lining plates. This applies to both the quenching cars used for wet quenching and the hot-coke cars used in the dry cooling process. Technical advances have been described whereby the life of car linings is prolonged by increasing heat emission from the lining plate surfaces. As the heat emission level is enhanced the mean plate temperature is lowered and the lining life thereby prolonged; moreover, the between-servicings period is prolonged. This involves providing fins on the non-working (outer) plate surfaces. The problem of optimizing the size and shape of the fins with reference to heat emission remains unsolved: the requirement is maximum heat emission from plates of a given weight, or conversely minimum plate weight for a given heat emission level. 6 refs., 3 figs.

Kotlyar, B.D.; Pleshkov, P.I.; Gadyatskii, V.G. [and others

1992-12-31T23:59:59.000Z

82

Assessing the Performance of 5mm White LED Light Sources for Developing-Country Applications  

E-Print Network [OSTI]

performance variations. Incandescent and fluorescent lightbetter than the common incandescent lamp. Off-grid lighting

Mills, Evan

2007-01-01T23:59:59.000Z

83

Acting Globally: Potential Carbon Emissions Mitigation Impacts from an International Standards and Labelling Program  

E-Print Network [OSTI]

both fluorescent and incandescent), standby power (forFluorescent Tubes Incandescent Lamps All % of CFL variableRefrigerator Savings Incandescent Lamp Savings Fluorescent

Letschert, Virginie E.

2010-01-01T23:59:59.000Z

84

Residential Electricity Demand in China -- Can Efficiency Reverse the Growth?  

E-Print Network [OSTI]

2000: Lighting Type Incandescent Fluorescent CFL Percentagescenario, we assume that incandescent bulbs are graduallyW 60W 15W Fluorescent Lamps Incandescent Lamps CFL We then

Letschert, Virginie

2010-01-01T23:59:59.000Z

85

ENERGY EFFICIENT LIGHTING PROGRAM. CHAPTER FROM THE ENERGY AND ENVIRONMENT DIVISION ANNUAL REPORT 1979  

E-Print Network [OSTI]

socket for a standard incandescent lamp. Once the diffuserwhether the lamp is fluorescent or incandescent, Comparedto the incandescent lamp, the circline fluorescent improves

Berman, S.

2013-01-01T23:59:59.000Z

86

Synthesis and luminescence properties of rare earth activated phosphors for near UV-emitting LEDs for efficacious generation of white light  

E-Print Network [OSTI]

lighting using incandescent lights and fluorescent lamps, asenergy used for the incandescent lamp is wasted as infraredsource to replace incandescent and fluorescent lighting [2].

Han, Jinkyu

2013-01-01T23:59:59.000Z

87

Assessing the Performance of LED-Based Flashlights Available in the Kenyan Off-Grid Lighting Market  

E-Print Network [OSTI]

have largely displaced incandescent flashlights in retailinvolving the use of incandescent lighting, unless there areFluorescent Flashlight C Incandescent SPX 50 Fluorescent y x

Tracy, Jennifer

2010-01-01T23:59:59.000Z

88

RPI students supporting education outreach Target Audience: Elementary school students (grades 3-6)  

E-Print Network [OSTI]

) Lowe's or Home Depot Approx. $22.00 each Compact Fluorescent Bulb 40 Lumen equivalent (GE) Lowe Introduction and Bulb Comparison; LED, Compact Fluorescent, Incandescent Bulb Comparison #12;Resistor Kit (incl (top position), compact fluorescent (middle position), LED Bulb (lower position). Computer set up

Linhardt, Robert J.

89

Comparison of 60-Hz electric fields and incandescent light as aversive stimuli controlling the behavior of rats  

SciTech Connect (OSTI)

Rats were exposed to two procedures which enabled them to press a lever to turn off a 90 or 100 kV/m 60-Hz electric field or, later in the study, illumination from an incandescent lamp. Under one procedure, a response turned off the stimulus for a fixed duration, after which the stimulus was turned on again. A response during the off-period restarted the fixed duration. None of the rats turned the field off reliably. Next, under an alternative procedure, pressing one lever turned the field off; pressing the other lever turned it back on; responding under those conditions differed little from that seen at 0 kV/m. Under both procedures, when illumination from an incandescent lamp served as the stimulus, each rat did turn the stimulus off, and performances varied with stimulus intensity. The results show that a 100 kV/m 60-Hz electric field is not sufficient to function as an aversive stimulus under two procedures where illumination from a lamp does function as an aversive stimulus.

Stern, S.; Laties, V.G.

1989-01-01T23:59:59.000Z

90

Energy 101: Lighting Choices | Department of Energy  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

in your home to energy-saving incandescent, compact fluorescent lamp (CFL), or light emitting diode (LED) bulbs could save you about 50 per year. For more information on lighting...

91

Resolve to Save Energy This Year | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

STAR bulbs, you could save 75 a year in energy costs. Compared to traditional incandescent bulbs, compact fluorescent bulbs can yield as much as 75 percent energy savings and...

92

Theoretical and experimental investigations into the particular features of the process of converting coal gas hydrocarbons on incandescent coke  

SciTech Connect (OSTI)

The prospects of the use of reducing gases in ferrous metallurgy and the possibilities for using them as a basis for coke production have been presented by the authors of the present article in the past. In the present report, the authors present certain results of theoretical and experimental investigations into the process of converting coal gas hydrocarbons on incandescent coke. The modification of the present-day method of thermodynamically calculating stable compositions of coking products, which was developed by the authors, has made it possible to apply it to specific chemical systems and process conditions not met with before, such as the conversion of hydrocarbons in mixtures of actual industrial gases (coal gas and blast furnace gas) in the presence of carbon and considerable amounts of hydrogen.

Zubilin, I.G.; Umanskii, V.E.

1984-01-01T23:59:59.000Z

93

Calendar Year 2007 Program Benefits for ENERGY STAR Labeled Products  

E-Print Network [OSTI]

weighted average across incandescent, CFL, and non-ENERGYreports power savings from incandescent/CFL lamp replacementreplacement of a 65 W incandescent lamp with a 16 W compact

Sanchez, Marla Christine

2008-01-01T23:59:59.000Z

94

Zinc Oxide and Nitride Nanowire Based Light Emitting Diodes  

E-Print Network [OSTI]

only be able to find incandescent lightbulbs and fluorescent10: Output spectra of incandescent light bulb, fluorescentemission spectra. The incandescent light bulb for example

Lai, Elaine Michelle

2009-01-01T23:59:59.000Z

95

Estimate of Technical Potential for Minimum Efficiency Performance Standards in 13 Major World Economies  

E-Print Network [OSTI]

for typical wattage of incandescent bulbs and hours of usagefor which we assume that incandescent bulbs gradually getsimilar to that of incandescent or fluorescent bulbs. These

Letschert, Virginie

2013-01-01T23:59:59.000Z

96

Global Potential of Energy Efficiency Standards and Labeling Programs  

E-Print Network [OSTI]

lighting (replacement of incandescent lamps with CFLs) withof each type of lamp: incandescent; fluorescent tubes; andless consumptive than incandescent bulbs. Second, it impacts

McNeil, Michael A

2008-01-01T23:59:59.000Z

97

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 Through 2011  

E-Print Network [OSTI]

Fluorescent Lamps and Incandescent Reflector Lamps EPACTBallasts and Fixtures General Service Incandescent Lamps,Intermediate Base Incandescent Lamps and Candelabra Base

Meyers, Stephen

2013-01-01T23:59:59.000Z

98

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 through 2012  

E-Print Network [OSTI]

Fluorescent Lamps and Incandescent Reflector Lamps EPACTBallasts and Fixtures General Service Incandescent Lamps,Intermediate Base Incandescent Lamps and Candelabra Base

Meyers, Stephen

2013-01-01T23:59:59.000Z

99

Controls for Solid-State Lighting  

E-Print Network [OSTI]

very high would replace incandescent and halogen A modernmotion sensor, the incandescent lamp switches on providing awork with fluorescent and incandescent lighting as well as

Rubinstein, Francis

2007-01-01T23:59:59.000Z

100

Energy and Economic Impacts of U.S. Federal Energy and Water Conservation Standards Adopted From 1987 Through 2010  

E-Print Network [OSTI]

Fluorescent Lamps and Incandescent Reflector Lamps MediumBallasts and Fixtures General Service Incandescent Lamps,Intermediate Base Incandescent Lamps and Candelabra Base

Meyers, Stephen

2013-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "incandescent compact fluorescent" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Energy Management A Program of Energy Conservation for the Community College Facility  

E-Print Network [OSTI]

whenever possible) Lamps Type (incandescent, fluorescent,are as follows: Lamp Type Incandescent FI uorescent Mercurylumens/watt lumens/watt Incandescent Mercury Metal Additive

Authors, Various

2011-01-01T23:59:59.000Z

102

Optimizing Energy Savings from Direct-DC in U.S. Residential Buildings  

E-Print Network [OSTI]

52LPW assuming 80% incandescent @14LPW goes to CFL @52LPWthan the traditional incandescent lighting it is replacingbest technology Lighting Incandescent, fluorescent, LED

Garbesi, Karina

2012-01-01T23:59:59.000Z

103

Pecos River Compact (Texas)  

Broader source: Energy.gov [DOE]

This legislation authorizes the state's entrance into the Pecos River Compact, a joint agreement between the states of New Mexico and Texas. The compact is administered by the Pecos River Compact...

104

THE HISTORY AND TECHNICAL EVOLUTION OF HIGH FREQUENCY FLUORESCENT LIGHTING  

E-Print Network [OSTI]

B L U E , G R E E N , INCANDESCENT FORM OF LAMPS OF VARIOUSTHE E F F I C I E N C Y INCANDESCENT A P P L I C A T I O N SI M E S , DEPENDING THE THE INCANDESCENT GENERAL LAMPS. THE

Campbell, John H.

2011-01-01T23:59:59.000Z

105

Zinc Oxide and Nitride Nanowire Based Light Emitting Diodes  

E-Print Network [OSTI]

of incandescent light bulb, fluorescent lamp, and blue lightof incandescent light bulb, fluorescent lamp, and blue lightincandescent bulb and is on the same order as fluorescent

Lai, Elaine Michelle

2009-01-01T23:59:59.000Z

106

Sleep, mood, and circadian responses to bright green light during sleep  

E-Print Network [OSTI]

white light from fluorescent bulbs, as point sources mightthan incandescent bulbs. Also, fluorescent light is easier

Grandner, Michael Andrew

2007-01-01T23:59:59.000Z

107

Electrical and Optical Enhancement in Internally Nanopatterned Organic Light-Emitting Diodes  

E-Print Network [OSTI]

incandescent bulbs and fluorescent bulbs). Solid-stateindex (CRI) than fluorescent bulbs. Common examples where

Fina, Michael Dane

2012-01-01T23:59:59.000Z

108

Residential and Transport Energy Use in India: Past Trend and Future Outlook  

E-Print Network [OSTI]

type of lighting bulb (incandescent, fluorescent), number ofof incandescent bulbs and fluorescent tubes per household,incandescent bulbs of 60W and 2.1 fluorescent tubes of 40W

de la Rue du Can, Stephane

2009-01-01T23:59:59.000Z

109

Red River Compact (Texas)  

Broader source: Energy.gov [DOE]

The Red River Compact Commission administers the Red River Compact to ensure that Texas receives its equitable share of quality water from the Red River and its tributaries as apportioned by the...

110

Canadian River Compact (Texas)  

Broader source: Energy.gov [DOE]

The Canadian River Commission administers the Canadian River Compact which includes the states of New Mexico, Oklahoma, and Texas. Signed in 1950 by the member states, the Compact was subsequently...

111

NSTX LTXPEGASUS Compact CTF  

E-Print Network [OSTI]

isotope retention. ST-CTF Compact ST-CTF at ~ 10 MA range provide a compact nuclear component test to NSTX. Large vacuum vessel, no stabilizing plates, excellent set of profile and boundary diagnostics

Princeton Plasma Physics Laboratory

112

Integrated ultrasonic particle positioning and low excitation light fluorescence imaging  

SciTech Connect (OSTI)

A compact hybrid system has been developed to position and detect fluorescent micro-particles by combining a Single Photon Avalanche Diode (SPAD) imager with an acoustic manipulator. The detector comprises a SPAD array, light-emitting diode (LED), lenses, and optical filters. The acoustic device is formed of multiple transducers surrounding an octagonal cavity. By stimulating pairs of transducers simultaneously, an acoustic landscape is created causing fluorescent micro-particles to agglomerate into lines. The fluorescent pattern is excited by a low power LED and detected by the SPAD imager. Our technique combines particle manipulation and visualization in a compact, low power, portable setup.

Bernassau, A. L.; Al-Rawhani, M.; Beeley, J.; Cumming, D. R. S. [School of Engineering, University of Glasgow, Glasgow, G12 8LT (United Kingdom)] [School of Engineering, University of Glasgow, Glasgow, G12 8LT (United Kingdom)

2013-12-09T23:59:59.000Z

113

Interstate Mining Compact (Maryland)  

Broader source: Energy.gov [DOE]

This legislation authorizes the state's entrance into the Interstate Mining Compact, a multi-state governmental agency / organization that represents the natural resource and related environmental...

114

Most new recessed downlights in the commercial sector use compact  

E-Print Network [OSTI]

CFL downlight systems--one each for commercial and residential markets--that reduce both energy: · PIER project site: www.energy.ca.gov/pier/buildings/ projects/500-01-041-0-4-4_3.html · PIER contractorMost new recessed downlights in the commercial sector use compact fluorescent lamps (CFLs

115

The Boom of Electricity Demand in the Residential Sector in the Developing World and the Potential for Energy Efficiency  

E-Print Network [OSTI]

for fluorescent and incandescent lamps. Estimates of thein Table 3. Table 3 Incandescent, Fluorescent and CFL lampthe surveys is 60W for incandescent bulb, 15W for CFLs and

Letschert, Virginie

2010-01-01T23:59:59.000Z

116

Bottom-Up Energy Analysis System - Methodology and Results  

E-Print Network [OSTI]

Documents U.S. Rulemaking Documents TSL 4 PHP IncandescentLamps Incandescent Lamps Fluorescent Lamp Ballasts kWh/yrand T5 fluorescent tubes, incandescent lamps, CFLs, Halogen

McNeil, Michael A.

2013-01-01T23:59:59.000Z

117

Stabilization of compactible waste  

SciTech Connect (OSTI)

This report summarizes the results of series of experiments performed to determine the feasibility of stabilizing compacted or compactible waste with polymers. The need for this work arose from problems encountered at disposal sites attributed to the instability of this waste in disposal. These studies are part of an experimental program conducted at Brookhaven National Laboratory (BNL) investigating methods for the improved solidification/stabilization of DOE low-level wastes. The approach taken in this study was to perform a series of survey type experiments using various polymerization systems to find the most economical and practical method for further in-depth studies. Compactible dry bulk waste was stabilized with two different monomer systems: styrene-trimethylolpropane trimethacrylate (TMPTMA) and polyester-styrene, in laboratory-scale experiments. Stabilization was accomplished by wetting or soaking compactible waste (before or after compaction) with monomers, which were subsequently polymerized. Three stabilization methods are described. One involves the in-situ treatment of compacted waste with monomers in which a vacuum technique is used to introduce the binder into the waste. The second method involves the alternate placement and compaction of waste and binder into a disposal container. In the third method, the waste is treated before compaction by wetting the waste with the binder using a spraying technique. A series of samples stabilized at various binder-to-waste ratios were evaluated through water immersion and compression testing. Full-scale studies were conducted by stabilizing two 55-gallon drums of real compacted waste. The results of this preliminary study indicate that the integrity of compacted waste forms can be readily improved to ensure their long-term durability in disposal environments. 9 refs., 10 figs., 2 tabs.

Franz, E.M.; Heiser, J.H. III; Colombo, P.

1990-09-01T23:59:59.000Z

118

Laboratory compaction of cohesionless sands  

E-Print Network [OSTI]

on the maximum dry unit weight during compaction. Three different laboratory compaction methods were used: 1) Standard Proctor', 2) Modified Proctor; and 3) Vibrating hammer. The effects of the grain size distribution, particle shape and laboratory compaction...

Delphia, John Girard

1998-01-01T23:59:59.000Z

119

Compact microchannel system  

DOE Patents [OSTI]

The present invention provides compact geometries for the layout of microchannel columns through the use of turns and straight channel segments. These compact geometries permit the use of long separation or reaction columns on a small microchannel substrate or, equivalently, permit columns of a fixed length to occupy a smaller substrate area. The new geometries are based in part on mathematical analyses that provide the minimum turn radius for which column performance in not degraded. In particular, we find that straight channel segments of sufficient length reduce the required minimum turn radius, enabling compact channel layout when turns and straight segments are combined. The compact geometries are obtained by using turns and straight segments in overlapped or nested arrangements to form pleated or coiled columns.

Griffiths, Stewart

2003-09-30T23:59:59.000Z

120

Conservation Potential of Compact Fluorescent Lamps in India and Brazil  

E-Print Network [OSTI]

energia: 0 Horario de Verao) Proceedings, I Congres- so Brasileiro de Planejamento Energetico (forthcoming), Universidade Es- tadual de Campinas, Sao Paulo, Brasil,

Gadgil, A.J.

2008-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "incandescent compact fluorescent" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Conservation Potential of Compact Fluorescent Lamps in India and Brazil  

E-Print Network [OSTI]

1.7% of in- stalled hydroelectric capacity. Op. cit. ref [in Ig86) based on hydroelectric generation, and most of thethe still abundant hydroelectric potential of the country.

Gadgil, A.J.

2008-01-01T23:59:59.000Z

122

Zero energy-storage ballast for compact fluorescent lamps  

DOE Patents [OSTI]

A CFL ballast includes complementary-type switching devices connected in series with their gates connected together at a control node. The switching devices supply a resonant tank circuit which is tuned to a frequency near, but slightly lower than, the resonant frequency of a resonant control circuit. As a result, the tank circuit restarts oscillations immediately following each zero crossing of the bus voltage. Such rapid restarts avoid undesirable flickering while maintaining the operational advantages and high efficacy of the CFL ballast. 4 figs.

Schultz, W.N.; Thomas, R.J.

1999-08-31T23:59:59.000Z

123

Zero energy-storage ballast for compact fluorescent lamps  

DOE Patents [OSTI]

A CFL ballast includes complementary-type switching devices connected in series with their gates connected together at a control node. The switching devices supply a resonant tank circuit which is tuned to a frequency near, but slightly lower than, the resonant frequency of a resonant control circuit. As a result, the tank circuit restarts oscillations immediately following each zero crossing of the bus voltage. Such rapid restarts avoid undesirable flickering while maintaining the operational advantages and high efficacy of the CFL ballast.

Schultz, William Newell (Niskayuna, NY); Thomas, Robert James (Rexford, NY)

1999-01-01T23:59:59.000Z

124

Lighting the Way with Compact Fluorescent Lighting | Department of Energy  

Energy Savers [EERE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion |Energy UsageAUDITVehicles »Exchange Visitorsfor Shade Landscaping for ShadeLessonsLight

125

Medium Base Compact Fluorescent Lamps | Department of Energy  

Energy Savers [EERE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Office of Inspector General Office0-72.pdfGeorgeDoesn't32 Master EM Project Definitionof

126

Covered Product Category: Compact Fluorescent Lamps | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:Year in Review: Top FiveDepartmentfor EngineeringDepartment ofBoilers CoveredDepartment

127

Energy Cost Calculator for Compact Fluorescent Lamps | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "ofEarly Career Scientists'Montana.Program -Department of Energy benchmarking.Department ofcapacity size,This

128

Conservation Potential of Compact Fluorescent Lamps in India and Brazil  

E-Print Network [OSTI]

household income is a strong determinant of household electricity use, analysis for different prices

Gadgil, A.J.

2008-01-01T23:59:59.000Z

129

EA-1664: Final Environmental Assessment  

Broader source: Energy.gov [DOE]

10 CFR Part 430 Energy Conservation Standards: Energy Conservation Standards for Fluorescent and Incandescent Lamps

130

Sustainable LED Fluorescent Light Replacement Technology  

SciTech Connect (OSTI)

Ilumisys and the National Center for Manufacturing Sciences (NCMS) partnered on a three-year project awarded by the United States (U.S.) Department of Energy (DOE), to quantify the impacts of LED lamps, incandescent lamps and fluorescent benchmark lamps over a product lifecycle i.e. to develop a sustainable design and manufacturing strategy that addresses product manufacturing, use, recycling and disposal scenarios for LED-based lighting. Based on the knowledge gained from extensive product tear-down studies of fluorescent and screw-in lighting products, lifecycle assessment tools, and accelerated lifecycle testing protocols, an interactive Sustainable LED Design Guide has been developed to aid architectural and lighting designers and engineers in making design decisions that consider three important environmental impacts (greenhouse gas emissions, energy use and mercury emission) across all phases of the life of an LED lighting product. Critical information developed for the lifecycle analysis and product feature comparisons is the useful life of the lighting product as well as its performance. The Design Guide is available at www.ncms.org, and was developed based on operational and durability testing of a variety of lighting products including power consumption, light output, and useful life of a lamp in order to allow a more realistic comparison of lamp designs. This report describes the main project tasks, results and innovative features of the lifecycle assessment (LCA)-based design tools, and the key considerations driving the sustainable design of LED lighting systems. The Design Guide incorporates the following three novel features for efficiently evaluating LED lighting features in value-chains: Bill-of-Materials (BOM) Builder Designers may import process data for each component and supply functional data for the product, including power, consumption, lumen output and expected useful life. Environmental Impact Review Designs are comparable across lifecycle phases, subsystems, and environmental impact category, and can be normalized to a userdefined functional unit. Drill-down Review These provide an indepth look at individual lamp designs with the ability to review across subsystem or lifecycle phase.

None

2011-06-30T23:59:59.000Z

131

Optimizing Energy Savings from Direct-DC in U.S. Residential Buildings  

E-Print Network [OSTI]

Appliance type Standard technology DC-internal best technology Lighting Incandescent, fluorescent, LED Incandescent Electronic Heating Heater Electric resistance Cooling Motor (& compressor,

Garbesi, Karina

2012-01-01T23:59:59.000Z

132

Industrial Optimization Compact Course  

E-Print Network [OSTI]

Industrial Optimization Compact Course and Challenge Workshop Optimization plays a crucial role of the processes are typically nonlinear and dyna- mic. Thus, complex dynamic optimization or optimal control in industrial optimization. February 17­20, 2014 ·9.00­17.00 IWR ·Im Neuenheimer Feld 368 ·69120 Heidelberg www

Kirches, Christian

133

Sabine River Compact (Multiple States)  

Broader source: Energy.gov [DOE]

The Sabine River Compact Commission administers the Sabine River Compact to ensure that Texas receives its equitable share of quality water from the Sabine River and its tributaries as apportioned...

134

Spatial assessment of net mercury emissions from the use of fluorescent bulbs  

SciTech Connect (OSTI)

While fluorescent lighting is an important technology for reducing electrical energy demand, mercury used in the bulbs is an ongoing concern. Using state and country level data, net emissions of mercury from the marginal use of fluorescent lightbulbs are examined for a base year of 2004 for each of the 50 United States and 130 countries. Combustion of coal for electric power generation is generally the largest source of atmospheric mercury pollution; reduction in electricity demand from the substitution of incandescent bulbs with fluorescents leads to reduced mercury emissions during the use of the bulb. This analysis considers the local mix of power sources, coal quality, thermal conversion efficiencies, distribution losses, and any mercury control technologies that might be in place. Emissions of mercury from production and end-of-life treatment of the bulbs are also considered, providing a life-cycle perspective. Net reductions in mercury over the entire life cycle range from -1.2 to 97 mg per bulb depending on the country. The consequences for atmospheric mercury emissions of several policy scenarios are also discussed. 46 refs., 4 figs., 3 tabs.

Matthew J. Eckelman; Paul T. Anastas; Julie B. Zimmerman [Yale University, New Haven, CT (United States). Department of Chemical Engineering

2008-11-15T23:59:59.000Z

135

Residential and Transport Energy Use in India: Past Trend and Future Outlook  

E-Print Network [OSTI]

type of lighting bulb (incandescent, fluorescent), number ofhouseholds possessed 3.2 incandescent bulbs of 60W and 2.1areas versus only 2.1 incandescent bulbs of 60W and 1.5

de la Rue du Can, Stephane

2009-01-01T23:59:59.000Z

136

STATE OF CALIFORNIA CERTIFICATE OF COMPLIANCE AND FIELD INSPECTION CHECKLIST  

E-Print Network [OSTI]

Watts: 1. Type of luminaire (i.e.: post top, wall pack, surface, shoe box); for non-incandescent luminaires, indicate nominal lamp wattage and lamp type ( i.e.: fluorescent, incandescent, HID); ballast type. For incandescent luminaires, the lum

137

Compact Spreader Schemes  

SciTech Connect (OSTI)

This paper describes beam distribution schemes adopting a novel implementation based on low amplitude vertical deflections combined with horizontal ones generated by Lambertson-type septum magnets. This scheme offers substantial compactness in the longitudinal layouts of the beam lines and increased flexibility for beam delivery of multiple beam lines on a shot-to-shot basis. Fast kickers (FK) or transverse electric field RF Deflectors (RFD) provide the low amplitude deflections. Initially proposed at the Stanford Linear Accelerator Center (SLAC) as tools for beam diagnostics and more recently adopted for multiline beam pattern schemes, RFDs offer repetition capabilities and a likely better amplitude reproducibility when compared to FKs, which, in turn, offer more modest financial involvements both in construction and operation. Both solutions represent an ideal approach for the design of compact beam distribution systems resulting in space and cost savings while preserving flexibility and beam quality.

Placidi, M.; Jung, J. -Y.; Ratti, A.; Sun, C.

2014-07-25T23:59:59.000Z

138

Energy Consumption, Efficiency, Conservation, and Greenhouse Gas Mitigation in Japan's Building Sector  

E-Print Network [OSTI]

and a washroom with bulb-type fluorescent lamps, (5) closingusing incandescent bulbs to fluorescent lamps. This switch

2006-01-01T23:59:59.000Z

139

Compact LINAC for deuterons  

SciTech Connect (OSTI)

We are developing a compact deuteron-beam accelerator up to the deuteron energy of a few MeV based on room-temperature inter-digital H-mode (IH) accelerating structures with the transverse beam focusing using permanent-magnet quadrupoles (PMQ). Combining electromagnetic 3-D modeling with beam dynamics simulations and thermal-stress analysis, we show that IHPMQ structures provide very efficient and practical accelerators for light-ion beams of considerable currents at the beam velocities around a few percent of the speed of light. IH-structures with PMQ focusing following a short RFQ can also be beneficial in the front end of ion linacs.

Kurennoy, S S [Los Alamos National Laboratory; O' Hara, J F [Los Alamos National Laboratory; Rybarcyk, L J [Los Alamos National Laboratory

2008-01-01T23:59:59.000Z

140

Comparison of technologies for new energy-efficient lamps  

SciTech Connect (OSTI)

Energy-efficient light bulbs are being developed to replace the incandescent lamp where they can satisfy the design criteria and be used in sockets that have long hours of annual use. The four technologies discussed here include the compact fluorescent lamp, coated-filament lamp, electrodeless fluorescent lamp, and compact high-intensity discharge lamp. The systems demonstrate efficacy improvements of two to four times that of their incandescent counterparts. These new lamps have required considerable advances in lamp technology. They offer the potential for achieving efficacies close to 80 lumens per watt. These new lamps will reduce the energy used annually by incandescent lamps (190 BkWh) by more than 50% in the 1990s, at which times they will be commonly employed.

Verderber, R.R.; Rubinstein, F.R.

1983-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "incandescent compact fluorescent" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Comparison of technologies for new energy-efficient lamps  

SciTech Connect (OSTI)

Energy-efficient light bulbs are being developed to replace the incandescent lamp where they can satisfy the design criteria and be used in sockets that have long hours of annual use. The four technologies discussed include the compact fluorescent lamp, coated-filament lamp, electrodeless fluorescent lamp, and compact high-intensity discharge lamp. The systems demonstrate efficacy improvements of two to four times that of their incandescent counterparts. These new lamps have required considerable advances in lamp technology. They offer the potential for achieving efficacies close to 80 lm/W. These new lamps will reduce the energy used annually by incandescent lamps (190 billion kWh) by more than 50 percent in the 1990's, at which times they will be commonly employed.

Verderber, R.R.; Rubinstein, F.M.

1984-09-01T23:59:59.000Z

142

Table Set-up with equipment Target Audience: Parents of elementary school students (grades 3-6), Middle and High School Students  

E-Print Network [OSTI]

Compact Fluorescent Bulb 40 Lumen equivalent (GE) Lowe's or Home Depot Approx. $6.50 each Incandescent engineering measurement tool 2. Introduce the range of light bulb options available for home use. 3. Describe the specifications generally provided to the consumer to evaluate available bulbs for home use 4. Provide hands

Linhardt, Robert J.

143

Energy Efficiency ISSN 1570-646X  

E-Print Network [OSTI]

ConEd Consolidated Edison CRT Cathode ray tube LCD Liquid crystal display LED Light emitting diode included combustion, incandescent and compact fluorescent (CFL) bulbs, and now light emitting diode (LED emitting diodes (LED), has been sug- gested as a way of reducing energy used for lighting. Such predictions

Illinois at Chicago, University of

144

Energy Savings and Green Initiatives Project Grant  

SciTech Connect (OSTI)

This project entails retrofitting all four foot, 2, 3 and 4 bulb 40 watt T12 fixtures to T8 28 watt and 150 watt incandescent to 26 watt compact fluorescent bulbs. In total, 2,086 fixtures will be retrofitted

Kathy MacLennan

2011-11-21T23:59:59.000Z

145

The Spectrum of Clean Energy Innovationinnovati nGreen Light-Emitting Diode Makes  

E-Print Network [OSTI]

- ing as an efficient solid-state light source, able to replace incandescent and compact fluorescent light bulbs in many applications. A new green LED from NREL may yield more efficient solid to accelerating market deployment, NREL works in partnership with private industry to drive the transformation

146

Today LED Holiday Lights, Tomorrow the World?  

SciTech Connect (OSTI)

This article for The APEM Advantage, the quarterly newsletter of the Association of Professional Energy Managers (APEM) describes the recent increase in the popularity of light emitting diode (LED) lighting and compares LED light output with that of incandescent and compact fluorescent lighting.

Gordon, Kelly L.

2004-12-20T23:59:59.000Z

147

Incandescent Lighting | Department of Energy  

Office of Environmental Management (EM)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "of Energy Power.pdf11-161-LNG | Department ofHTS CableDepartment ofDepartment ofDepartmentInauguration

148

Accretion in Compact Binaries  

E-Print Network [OSTI]

Compact binaries have long been a paradigm for accretion theory. Much of our present view of how accretion occurs comes directly from the comparison of theory with observations of these sources. Since theory differs little for other objects such as active galaxies, increasing efforts have recently gone into searching for correspondences in observed behaviour. This chapter aims at giving a concise summary of the field, with particular emphasis on new developments since the previous edition of this book. These developments have been significant. Much of the earlier literature implicitly assumed that accreting binaries were fairly steady sources accreting most of the mass entering their vicinity, often with main-sequence companions, and radiating the resulting accretion luminosity in rough isotropy. We shall see that in reality these assumptions fail for the majority of systems. Most are transient; mass ejection in winds and jets is extremely common; a large (sometimes dominant) fraction of even short-period systems have evolved companions whose structure deviates significantly from the zero-age main sequence; and the radiation pattern of many objects is significantly anisotropic. It is now possible to give a complete characterization of the observed incidence of transient and persistent sources in terms of the disc instability model and formation constraints. X-ray populations in external galaxies, particularly the ultraluminous sources, are revealing important new insights into accretion processes and compact binary evolution.

Andrew R. King

2003-03-26T23:59:59.000Z

149

Susquehanna River Basin Compact (Maryland)  

Broader source: Energy.gov [DOE]

This legislation enables the state's entrance into the Susquehanna River Basin Compact, which provides for the conservation, development, and administration of the water resources of the...

150

Fluorescent Tube Lamps  

Broader source: Energy.gov [DOE]

FEMP temporarily suspended its energy efficiency requirements for fluorescent tube lamps as it evaluates the market impact of the pending 2012 minimum efficiency standards for fluorescent lamps. The program will issue updated energy efficiency requirements when the market distribution of this product category stabilizes and when doing so has the potential to result in significant Federal energy savings.

151

Compact acoustic refrigerator  

DOE Patents [OSTI]

A compact acoustic refrigeration system actively cools components, e.g., electrical circuits, in a borehole environment. An acoustic engine includes first thermodynamic elements for generating a standing acoustic wave in a selected medium. An acoustic refrigerator includes second thermodynamic elements located in the standing wave for generating a relatively cold temperature at a first end of the second thermodynamic elements and a relatively hot temperature at a second end of the second thermodynamic elements. A resonator volume cooperates with the first and second thermodynamic elements to support the standing wave. To accommodate the high heat fluxes required for heat transfer to/from the first and second thermodynamic elements, first heat pipes transfer heat from the heat load to the second thermodynamic elements and second heat pipes transfer heat from first and second thermodynamic elements to the borehole environment. 18 figs.

Bennett, G.A.

1992-11-24T23:59:59.000Z

152

Compact acoustic refrigerator  

DOE Patents [OSTI]

A compact acoustic refrigeration system actively cools components, e.g., electrical circuits (22), in a borehole environment. An acoustic engine (12, 14) includes first thermodynamic elements (12) for generating a standing acoustic wave in a selected medium. An acoustic refrigerator (16, 26, 28) includes second thermodynamic elements (16) located in the standing wave for generating a relatively cold temperature at a first end of the second thermodynamic elements (16) and a relatively hot temperature at a second end of the second thermodynamic elements (16). A resonator volume (18) cooperates with the first and second thermodynamic elements (12, 16) to support the standing wave. To accommodate the high heat fluxes required for heat transfer to/from the first and second thermodynamic elements (12, 16), first heat pipes (24, 26) transfer heat from the heat load (22) to the second thermodynamic elements (16) and second heat pipes (28, 32) transfer heat from first and second thermodynamic elements (12, 16) to the borehole environment.

Bennett, Gloria A. (Los Alamos, NM)

1992-01-01T23:59:59.000Z

153

Compact vacuum insulation  

DOE Patents [OSTI]

An ultra-thin compact vacuum insulation panel is comprised of two hard, but bendable metal wall sheets closely spaced apart from each other and welded around the edges to enclose a vacuum chamber. Glass or ceramic spacers hold the wall sheets apart. The spacers can be discrete spherical beads or monolithic sheets of glass or ceramic webs with nodules protruding therefrom to form essentially "point" or "line" contacts with the metal wall sheets. In the case of monolithic spacers that form "line" contacts, two such spacers with the line contacts running perpendicular to each other form effectively "point" contacts at the intersections. Corrugations accommodate bending and expansion, tubular insulated pipes and conduits, and preferred applications are also included.

Benson, David K. (Golden, CO); Potter, Thomas F. (Denver, CO)

1993-01-01T23:59:59.000Z

154

Compact vacuum insulation embodiments  

DOE Patents [OSTI]

An ultra-thin compact vacuum insulation panel is comprised of two hard, but bendable metal wall sheets closely spaced apart from each other and welded around the edges to enclose a vacuum chamber. Glass or ceramic spacers hold the wall sheets apart. The spacers can be discrete spherical beads or monolithic sheets of glass or ceramic webs with nodules protruding therefrom to form essentially "point" or "line" contacts with the metal wall sheets. In the case of monolithic spacers that form "line" contacts, two such spacers with the line contacts running perpendicular to each other form effectively "point" contacts at the intersections. Corrugations accommodate bending and expansion, tubular insulated pipes and conduits, and preferred applications are also included.

Benson, David K. (Golden, CO); Potter, Thomas F. (Denver, CO)

1992-01-01T23:59:59.000Z

155

Compact vacuum insulation embodiments  

DOE Patents [OSTI]

An ultra-thin compact vacuum insulation panel is comprised of two hard, but bendable metal wall sheets closely spaced apart from each other and welded around the edges to enclose a vacuum chamber. Glass or ceramic spacers hold the wall sheets apart. The spacers can be discrete spherical beads or monolithic sheets of glass or ceramic webs with nodules protruding therefrom to form essentially point' or line' contacts with the metal wall sheets. In the case of monolithic spacers that form line' contacts, two such spacers with the line contacts running perpendicular to each other form effectively point' contacts at the intersections. Corrugations accommodate bending and expansion, tubular insulated pipes and conduits, and preferred applications are also included. 26 figs.

Benson, D.K.; Potter, T.F.

1992-04-28T23:59:59.000Z

156

Fluorescent filtered electrophosphorescence  

DOE Patents [OSTI]

The present invention relates to organic light emitting devices (OLEDs), and more specifically to OLEDS that emit light using a combination of fluorescent emitters and phosphorescent emitters for the efficient utilization of all of the electrically generated excitons.

Forrest, Stephen (Ann Arbor, MI); Sun, Yiru (Princeton, NJ); Giebink, Noel (Ann Arbor, MI); Thompson, Mark E. (Anaheim Hills, CA)

2010-08-03T23:59:59.000Z

157

Fluorescent filtered electrophosphorescence  

DOE Patents [OSTI]

The present invention relates to organic light emitting devices (OLEDs), and more specifically to OLEDS that emit light using a combination of fluorescent emitters and phosphorescent emitters for the efficient utilization of all of the electrically generated excitons.

Forrest, Stephen R. (Princeton, NJ); Sun, Yiru (Princeton, NJ); Giebink, Noel (Princeton, NJ); Thompson, Mark E. (Anaheim Hills, CA)

2009-01-06T23:59:59.000Z

158

Compact neutron generator  

DOE Patents [OSTI]

A compact neutron generator has at its outer circumference a toroidal shaped plasma chamber in which a tritium (or other) plasma is generated. A RF antenna is wrapped around the plasma chamber. A plurality of tritium ion beamlets are extracted through spaced extraction apertures of a plasma electrode on the inner surface of the toroidal plasma chamber and directed inwardly toward the center of neutron generator. The beamlets pass through spaced acceleration and focusing electrodes to a neutron generating target at the center of neutron generator. The target is typically made of titanium tubing. Water is flowed through the tubing for cooling. The beam can be pulsed rapidly to achieve ultrashort neutron bursts. The target may be moved rapidly up and down so that the average power deposited on the surface of the target may be kept at a reasonable level. The neutron generator can produce fast neutrons from a T-T reaction which can be used for luggage and cargo interrogation applications. A luggage or cargo inspection system has a pulsed T-T neutron generator or source at the center, surrounded by associated gamma detectors and other components for identifying explosives or other contraband.

Leung, Ka-Ngo; Lou, Tak Pui

2005-03-22T23:59:59.000Z

159

Compact vacuum insulation  

DOE Patents [OSTI]

Improved compact insulation panel is provided which is comprised of two adjacent metal sheets spaced close together with a plurality of spherical, or other discretely shaped, glass or ceramic beads optimally positioned between the sheets to provide support and maintain the spacing between the metal sheets when the gases there between are evacuated to form a vacuum. These spherical glass beads provide the maximum support while minimizing thermal conductance. In its preferred embodiment; these two metal sheets are textured with ribs or concave protrusions in conjunction with the glass beads to maximize the structural integrity of the panels while increasing the spacing between beads, thereby reducing the number of beads and the number of thermal conduction paths. Glass or porcelain-enameled liners in combination with the glass spacers and metal sidewalls effectively decrease thermal conductivity, and various laminates, including wood, porcelain-enameled metal, and others effectively increase the strength and insulation capabilities of the panels. Also, a metal web is provided to hold the spacers in place, and strategic grooves are shown to accommodate expansion and contraction or shaping of the panels. 35 figs.

Benson, D.K.; Potter, T.F.

1992-10-27T23:59:59.000Z

160

Compact vacuum insulation  

DOE Patents [OSTI]

Improved compact insulation panel is provided which is comprised of two adjacent metal sheets spaced close together with a plurality of spherical, or other discretely shaped, glass or ceramic beads optimally positioned between the sheets to provide support and maintain the spacing between the metal sheets when the gases therebetween are evacuated to form a vacuum. These spherical glass beads provide the maximum support while minimizing thermal conductance. In its preferred embodiment; these two metal sheets are textured with ribs or concave protrusions in conjunction with the glass beads to maximize the structural integrity of the panels while increasing the spacing between beads, thereby reducing the number of beads and the number of thermal conduction paths. Glass or porcelain-enameled liners in combination with the glass spacers and metal sidewalls effectively decrease thermal conductivity, and variious laminates, including wood, porcelain-enameled metal, and others effectively increase the strength and insulation capabilities of the panels. Also, a metal web is provided to hold the spacers in place, and strategic grooves are shown to accommodate expansion and contraction or shaping of the panels.

Benson, David K. (Golden, CO); Potter, Thomas F. (Denver, CO)

1992-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "incandescent compact fluorescent" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Compaction managed mirror bend achromat  

DOE Patents [OSTI]

A method for controlling the momentum compaction in a beam of charged particles. The method includes a compaction-managed mirror bend achromat (CMMBA) that provides a beamline design that retains the large momentum acceptance of a conventional mirror bend achromat. The CMMBA also provides the ability to tailor the system momentum compaction spectrum as desired for specific applications. The CMMBA enables magnetostatic management of the longitudinal phase space in Energy Recovery Linacs (ERLs) thereby alleviating the need for harmonic linearization of the RF waveform.

Douglas, David (Yorktown, VA)

2005-10-18T23:59:59.000Z

162

Yellowstone River Compact (North Dakota)  

Broader source: Energy.gov [DOE]

The Yellowstone River Compact, agreed to by the States of Montana, North Dakota, and Wyoming, provides for an equitable division and apportionment of the waters of the Yellowstone River, as well as...

163

New considerations for compact cyclotrons  

E-Print Network [OSTI]

A compact cyclotron built with superconducting magnets could be a transformative solution to many scientific problems facing the defense, medical, and energy industries today. This thesis discusses three potential applications ...

Marshall, Eric S. (Eric Scott)

2012-01-01T23:59:59.000Z

164

MESOSCALE SIMULATIONS OF POWDER COMPACTION  

SciTech Connect (OSTI)

Mesoscale 3D simulations of shock compaction of metal and ceramic powders have been performed with an Eulerian hydrocode GEODYN. The approach was validated by simulating a well-characterized shock compaction experiment of a porous ductile metal. Simulation results using the Steinberg material model and handbook values for solid 2024 aluminum showed good agreement with experimental compaction curves and wave profiles. Brittle ceramic materials are not as well studied as metals, so a simple material model for solid ceramic (tungsten carbide) has been calibrated to match experimental compaction curves. Direct simulations of gas gun experiments with ceramic powders have been performed and showed good agreement with experimental data. The numerical shock wave profile has same character and thickness as that measured experimentally using VISAR. The numerical results show reshock states above the single-shock Hugoniot line as observed in experiments. We found that for good quantitative agreement with experiments 3D simulations are essential.

Lomov, Ilya; Fujino, Don; Antoun, Tarabay; Liu, Benjamin [Lawrence Livermore National Laboratory, P. O. Box 808, Livermore CA 94551 (United States)

2009-12-28T23:59:59.000Z

165

Fluorescence analyzer for lignin  

SciTech Connect (OSTI)

An apparatus for measuring lignin concentration with time resolved fluorescence in an undiluted wood pulp or black liquor sample, on a real-time, in situ basis is described, comprising: light source means for applying excitation light pulses at a selected wavelength and at known time intervals to the undiluted sample for causing the lignin concentration to produce fluorescent emission light with a fluorescence intensity that monotonically decreases in a quenched fluorescence regime; light detector means for measuring the emission light at the known time intervals and establishing signals indicative thereof; switching means for turning said light detector means on at precise specified time intervals after each excitation light pulse; and signal processing means connected to the light source means and the light detector means for comparing intensities of the emission light from the lignin in the quenched fluorescence regime to the intensities of the excitation light pulses on a time resolved basis for providing a measurement of the lignin concentration in the undiluted sample as a function of the time resolved emission light intensity.

Berthold, J.W.; Malito, M.L.; Jeffers, L.

1993-06-01T23:59:59.000Z

166

Fluorescent image tracking velocimeter  

DOE Patents [OSTI]

A multiple-exposure fluorescent image tracking velocimeter (FITV) detects and measures the motion (trajectory, direction and velocity) of small particles close to light scattering surfaces. The small particles may follow the motion of a carrier medium such as a liquid, gas or multi-phase mixture, allowing the motion of the carrier medium to be observed, measured and recorded. The main components of the FITV include: (1) fluorescent particles; (2) a pulsed fluorescent excitation laser source; (3) an imaging camera; and (4) an image analyzer. FITV uses fluorescing particles excited by visible laser light to enhance particle image detectability near light scattering surfaces. The excitation laser light is filtered out before reaching the imaging camera allowing the fluoresced wavelengths emitted by the particles to be detected and recorded by the camera. FITV employs multiple exposures of a single camera image by pulsing the excitation laser light for producing a series of images of each particle along its trajectory. The time-lapsed image may be used to determine trajectory and velocity and the exposures may be coded to derive directional information.

Shaffer, Franklin D. (Library, PA)

1994-01-01T23:59:59.000Z

167

X-ray fluorescence observations of the moon by SMART-1/D-CIXS and the first detection of Ti Ka from the lunar surface  

E-Print Network [OSTI]

X-ray fluorescence observations of the moon by SMART-1/D-CIXS and the first detection of Ti Ka from s t r a c t The demonstration of a compact imaging X-ray spectrometer (D-CIXS), which flew on ESA new technologies for orbital X-ray fluorescence spectroscopy. D-CIXS conducted observations

Wieczorek, Mark

168

Compact boson stars in K field theories  

E-Print Network [OSTI]

We study a scalar field theory with a non-standard kinetic term minimally coupled to gravity. We establish the existence of compact boson stars, that is, static solutions with compact support of the full system with self-gravitation taken into account. Concretely, there exist two types of solutions, namely compact balls on the one hand, and compact shells on the other hand. The compact balls have a naked singularity at the center. The inner boundary of the compact shells is singular, as well, but it is, at the same time, a Killing horizon. These singular, compact shells therefore resemble black holes.

C. Adam; N. Grandi; P. Klimas; J. Sanchez-Guillen; A. Wereszczynski

2009-09-16T23:59:59.000Z

169

Compact boson stars in K field theories  

E-Print Network [OSTI]

We study a scalar field theory with a non-standard kinetic term minimally coupled to gravity. We establish the existence of compact boson stars, that is, static solutions with compact support of the full system with self-gravitation taken into account. Concretely, there exist two types of solutions, namely compact balls on the one hand, and compact shells on the other hand. The compact balls have a naked singularity at the center. The inner boundary of the compact shells is singular, as well, but it is, at the same time, a Killing horizon. These singular, compact shells therefore resemble black holes.

Adam, C; Klimas, P; Snchez-Guilln, J; Wereszczynski, A

2009-01-01T23:59:59.000Z

170

Sensors and Actuators B 107 (2005) 121125 Two photon fluorescence sensors based on resonant grating  

E-Print Network [OSTI]

Sensors and Actuators B 107 (2005) 121­125 Two photon fluorescence sensors based on resonant the excitation and emission radia- tion reduces the background noise, the static photobleaching.07.040 #12;122 T. Katchalski et al. / Sensors and Actuators B 107 (2005) 121­125 lar, they are compact

Friesem, Asher A.

171

Compact orthogonal NMR field sensor  

DOE Patents [OSTI]

A Compact Orthogonal Field Sensor for emitting two orthogonal electro-magnetic fields in a common space. More particularly, a replacement inductor for existing NMR (Nuclear Magnetic Resonance) sensors to allow for NMR imaging. The Compact Orthogonal Field Sensor has a conductive coil and a central conductor electrically connected in series. The central conductor is at least partially surrounded by the coil. The coil and central conductor are electrically or electro-magnetically connected to a device having a means for producing or inducing a current through the coil and central conductor. The Compact Orthogonal Field Sensor can be used in NMR imaging applications to determine the position and the associated NMR spectrum of a sample within the electro-magnetic field of the central conductor.

Gerald, II, Rex E. (Brookfield, IL); Rathke, Jerome W. (Homer Glen, IL)

2009-02-03T23:59:59.000Z

172

Assessing the residential lighting efficiency opportunities in Guadalajara and Monterrey, Mexico  

SciTech Connect (OSTI)

Lighting, primarily with incandescent bulbs, is the major end use of electricity in Mexican homes. The introduction of compact fluorescent lamps (CFLs) could significantly reduce electricity use in lighting. We describe a survey of lighting use in homes of Guadalajara and Monterrey, Mexico, that was conducted to provide information to determine the potential for CDLs. The results show that 1/6 of the incandescent bulbs can be replaced with CFLs if only those bulbs used more than 4 hours per day are targeted. We also provide insights on conducting similar surveys in other developing countries.

Friedmann,R.; DeBuen,O; Sathaye,J.; Gadgil,A.; Saucedo,R.; Rodriguez,G.

1995-02-02T23:59:59.000Z

173

Fluorescent Protein Applications in Microscopy  

E-Print Network [OSTI]

. The Identification of Green Fluorescent Protein III. Formation of the GFP Chromophore IV. The Structure of GFP V environment. II. The Identification of Green Fluorescent Protein The isolation of green fluorescent protein of Aequorea, Shimomura et al. noted that the lumines- cence from aequorin was blue rather than the green

Straight, Aaron

174

Recommendations to Reduce Light Pollution and Energy Costs on the  

E-Print Network [OSTI]

(PAT18, PAT19, PAT27, PAT28, PAT29 - CL14): #12;· Change class #15, and class #20, incandescent bulbs with exterior fluorescent bulbs: · Change class #18 incandescent flood-light bulbs with fluorescent flood

175

Compact accelerator for medical therapy  

DOE Patents [OSTI]

A compact accelerator system having an integrated particle generator-linear accelerator with a compact, small-scale construction capable of producing an energetic (.about.70-250 MeV) proton beam or other nuclei and transporting the beam direction to a medical therapy patient without the need for bending magnets or other hardware often required for remote beam transport. The integrated particle generator-accelerator is actuable as a unitary body on a support structure to enable scanning of a particle beam by direction actuation of the particle generator-accelerator.

Caporaso, George J.; Chen, Yu-Jiuan; Hawkins, Steven A.; Sampayan, Stephen E.; Paul, Arthur C.

2010-05-04T23:59:59.000Z

176

Compact monolithic capacitive discharge unit  

DOE Patents [OSTI]

A compact monolithic capacitive discharge unit (CDU) is disclosed in which a thyristor switch and a flyback charging circuit are both sandwiched about a ceramic energy storage capacitor. The result is a compact rugged assembly which provides a low-inductance current discharge path. The flyback charging circuit preferably includes a low-temperature co-fired ceramic transformer. The CDU can further include one or more ceramic substrates for enclosing the thyristor switch and for holding various passive components used in the flyback charging circuit. A load such as a detonator can also be attached directly to the CDU.

Roesler, Alexander W. (Tijeras, NM); Vernon, George E. (Rio Rancho, NM); Hoke, Darren A. (Albuquerque, NM); De Marquis, Virginia K. (Tijeras, NM); Harris, Steven M. (Albuquerque, NM)

2007-06-26T23:59:59.000Z

177

Renewable Surface Fluorescence Sandwich Immunoassay Biosensor...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Renewable Surface Fluorescence Sandwich Immunoassay Biosensor for Rapid Sensitive Botulinum Toxin Detection in an Automated Renewable Surface Fluorescence Sandwich Immunoassay...

178

The Air-Fluorescence Yield  

E-Print Network [OSTI]

Detection of the air-fluorescence radiation induced by the charged particles of extensive air showers is a well-established technique for the study of ultra-high energy cosmic rays. Fluorescence telescopes provide a nearly calorimetric measure of the primary energy. Presently the main source of systematic uncertainties comes from our limited accuracy in the fluorescence yield, that is, the number of fluorescence photons emitted per unit of energy deposited in the atmosphere by the shower particles. In this paper the current status of our knowledge on the fluorescence yield both experimental an theoretical will be discussed.

F. Arqueros; F. Blanco; D. Garcia-Pinto; M. Ortiz; J. Rosado

2008-07-30T23:59:59.000Z

179

Hyperbolic capture of compact binaries  

E-Print Network [OSTI]

Hyperbolic encounters of compact objects are common interactions in dense environments. During this process a significant amount of gravitational radiation is emitted depending on the parameters of the system. Here we give a parametric description of the radial motion valid for general binary orbits and the radiative energy and angular momentum losses for binaries with spinning components.

Mtys Vasth

2014-09-23T23:59:59.000Z

180

CX-011406: Categorical Exclusion Determination | Department of...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Categorical Exclusion Determination Notice of Proposed Rulemaking for Energy Conservation Standards for General Service Fluorescent Lamps and Incandescent Reflector Lamps...

Note: This page contains sample records for the topic "incandescent compact fluorescent" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

4024 Inorg. Chem. 1987, 26, 4024-4029 Contribution from the Departments of Chemistry, Colgate University, Hamilton, New York 13346,  

E-Print Network [OSTI]

and laboratory fluorescent light and during nights to light from a 150-W incandescent bulb 20 cm from the pair

Herbert, Bruce

182

Business Case for Energy Efficiency in Support of Climate Change Mitigation, Economic and Societal Benefits in China  

E-Print Network [OSTI]

Commercial and Industrial End Uses Incandescent Lamps Refrigerators Residential AC (Including Heat Pumps) Washing Machines Fluorescent Ballasts Electric Water Heaters

McNeil, Michael A.

2012-01-01T23:59:59.000Z

183

Magnetic fluorescent lamp  

DOE Patents [OSTI]

The radiant emission of a mercury-argon discharge in a fluorescent lamp assembly is enhanced by providing means for establishing a magnetic field with lines of force along the path of electron flow through the bulb of the lamp assembly, to provide Zeeman splitting of the ultraviolet spectral line. Optimum results are obtained when the magnetic field strength causes a Zeeman splitting of approximately 1.7 times the thermal line width.

Berman, S.M.; Richardson R.W.

1983-12-29T23:59:59.000Z

184

The National Energy Policy Act and lamp replacement options  

SciTech Connect (OSTI)

The National Policy Act of 1992 involves the creation of energy efficiency standards for a wide range of products including fluorescent and incandescent lamps. Minimum efficacy (lumens per watt) and color rendering index (CRI) standards are mandated for the popular fluorescent lamps: four-foot medium bi-pin, two-foot U-bent, eight-foot slimline and eight-foot high output. Minimum efficacies are mandated for specific incandescent R and PAR reflector lamps. These standards will affect selected colors and designs of fluorescent lamps, the most significant being the standard lamps in the cool white and warm white colors. The incandescent reflector lamps will include the R-30, R-40, PAR-38 lamps above 40 watts, excluding the halogen types. These efficiency and color rendering standards will require end-users and specifiers to select replacement fluorescent lamps from a range of performance characteristics (lumen output, efficacy, CRI and price). The choice of replacement for the R and PAR incandescent lamps will include the halogen designs and compact fluorescent designs. In this paper, replacement options will be analyzed and discussed and the effect of these options on the performance of the lighting system will be explored in detail.

Ryerson, C.

1995-06-01T23:59:59.000Z

185

Interstate Oil and Gas Conservation Compact (Montana)  

Broader source: Energy.gov [DOE]

This legislation authorizes the State to join the Interstate Compact for the Conservation of Oil and Gas. The Compact is an agreement that has been entered into by 30 oil- and gas-producing states,...

186

Interstate Oil and Gas Conservation Compact (Maryland)  

Broader source: Energy.gov [DOE]

This legislation authorizes the State to join the Interstate Compact for the Conservation of Oil and Gas. The Compact is an agreement that has been entered into by 30 oil- and gas-producing states,...

187

Compact neutron generator development at LBNL  

E-Print Network [OSTI]

Generator Development at LBNL J. Reijonen, G. English, R.Technology Group in LBNL. The compact axial extraction

2003-01-01T23:59:59.000Z

188

Compact magnetic energy storage module  

DOE Patents [OSTI]

A superconducting compact magnetic energy storage module in which a plurality of superconducting toroids, each having a toroidally wound superconducting winding inside a poloidally wound superconducting winding, are stacked so that the flow of electricity in each toroidally wound superconducting winding is in a direction opposite from the direction of electrical flow in other contiguous superconducting toroids. This allows for minimal magnetic pollution outside of the module.

Prueitt, Melvin L. (Los Alamos, NM)

1994-01-01T23:59:59.000Z

189

Compact magnetic energy storage module  

DOE Patents [OSTI]

A superconducting compact magnetic energy storage module in which a plurality of superconducting toroids, each having a toroidally wound superconducting winding inside a poloidally wound superconducting winding, are stacked so that the flow of electricity in each toroidally wound superconducting winding is in a direction opposite from the direction of electrical flow in other contiguous superconducting toroids. This allows for minimal magnetic pollution outside of the module. 4 figures.

Prueitt, M.L.

1994-12-20T23:59:59.000Z

190

Fluorescent temperature sensor  

DOE Patents [OSTI]

The present invention is a fluorescent temperature sensor or optical thermometer. The sensor includes a solution of 1,3-bis(1-pyrenyl)propane within a 1-butyl-1-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide ionic liquid solvent. The 1,3-bis(1-pyrenyl)propane remains unassociated when in the ground state while in solution. When subjected to UV light, an excited state is produced that exists in equilibrium with an excimer. The position of the equilibrium between the two excited states is temperature dependent.

Baker, Gary A [Los Alamos, NM; Baker, Sheila N [Los Alamos, NM; McCleskey, T Mark [Los Alamos, NM

2009-03-03T23:59:59.000Z

191

Fluorescence analyzer for lignin  

SciTech Connect (OSTI)

A method and apparatus for measuring lignin concentration in a sample of wood pulp or black liquor comprises a light emitting arrangement for emitting an excitation light through optical fiber bundles into a probe which has an undiluted sensing end facing the sample. The excitation light causes the lignin concentration to produce fluorescent emission light which is then conveyed through the probe to analyzing equipment which measures the intensity of the emission light. Measures a This invention was made with Government support under Contract Number DOE: DE-FC05-90CE40905 awarded by the Department of Energy (DOE). The Government has certain rights in this invention.

Berthold, John W. (Salem, OH); Malito, Michael L. (Hubbard, OH); Jeffers, Larry (Alliance, OH)

1993-01-01T23:59:59.000Z

192

Development of a fluorescent cryocooler  

SciTech Connect (OSTI)

Recent work at Los Alamos National Laboratory has demonstrated the physical principles for a new type of solid-state cryocooler based on anti-Stokes fluorescence. Design studies indicate that a vibration-free, low-mass ``fluorescent cryocooler`` could operate for years with efficiencies and cooling powers comparable to current commercial systems. This paper presents concepts for a fluorescent cryocooler, design considerations and expected performance.

Edwards, B.C.; Buchwald, M.I.; Epstein, R.I.; Gosnell, T.R.; Mungan, C.E.

1995-10-01T23:59:59.000Z

193

X-ray fluorescence mapping  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

biololgical cells, over the measurement of impurities in solar cells, to the rare earth content of geological materials. A somewhat 'typical' layout for a X-ray fluorescence...

194

Identification of Nucleotides with Identical Fluorescent Labels Based on Fluorescence  

E-Print Network [OSTI]

Identification of Nucleotides with Identical Fluorescent Labels Based on Fluorescence Polarization for discriminating among the four DNA nucleotides la- beled identically with tetramethylrhodamine is described and demonstrated. Labeled nucleotides were dissolved in buffered surfactant solutions. In room temperature 4.5 m

Myrick, Michael Lenn

195

Compact Gamma-ray Source Technology Development Study  

SciTech Connect (OSTI)

This study focuses on the applicability of current accelerator and laser technologies to the construction of compact, narrow bandwidth, gamma-ray sources for DHS missions in illicit materials detection. It also identifies research and development areas in which advancement will directly benefit these light sources. In particular, we review the physics of Compton scattering based light sources and emphasize the source properties most important to Nuclear Resonance Fluorescence (NRF) applications of interest. The influences of laser and electron beam properties on the light source are examined in order to evaluate the utility of different technologies for this application. Applicable bulk and fiber-based laser systems and laser recirculation technologies are discussed and Radio Frequency (RF) Linear Accelerator (linac) technologies are examined to determine the optimal frequency and pulse formats achievable.

Anderson, S G; Gibson, D J; Rusnak, B

2009-09-25T23:59:59.000Z

196

COMPACT, TUNABLE COMPTON SCATTERING GAMMA-RAY SOURCES  

SciTech Connect (OSTI)

Recent progress in accelerator physics and laser technology have enabled the development of a new class of gamma-ray light sources based on Compton scattering between a high-brightness, relativistic electron beam and a high intensity laser pulse produced via chirped-pulse amplification (CPA). A precision, tunable gamma-ray source driven by a compact, high-gradient X-band linac is currently under development at LLNL. High-brightness, relativistic electron bunches produced by the linac interact with a Joule-class, 10 ps laser pulse to generate tunable {gamma}-rays in the 0.5-2.5 MeV photon energy range via Compton scattering. The source will be used to excite nuclear resonance fluorescence lines in various isotopes; applications include homeland security, stockpile science and surveillance, nuclear fuel assay, and waste imaging and assay. The source design, key parameters, and current status are presented.

Hartemann, F V; Albert, F; Anderson, G G; Anderson, S G; Bayramian, A J; Betts, S M; Chu, T S; Cross, R R; Ebbers, C A; Fisher, S E; Gibson, D J; Ladran, A S; Marsh, R A; Messerly, M J; O'Neill, K L; Semenov, V A; Shverdin, M Y; Siders, C W; McNabb, D P; Barty, C J; Vlieks, A E; Jongewaard, E N; Tantawi, S G; Raubenheimer, T O

2009-08-20T23:59:59.000Z

197

Compact bilinear operators and commutators  

E-Print Network [OSTI]

) For all bounded B1 ? X,B2 ? Y , T (B1 B2) is precompact. (c7) For all bounded sequences {(xn, yn)} ? X Y , the sequence {T (xn, yn)} has a convergent subsequence. Furthermore, if Z is Banach, then (c1) is also equivalent to: (c8) For all bounded B ? X...(X Y, Z) ? B(X Y, Z), assume that the compact bilinear operator T is not bounded. Then, for some r > 0, there exists a sequence (xn, yn) ? Br,XY , and ?T (xn, yn)? ? ?. Thus, {T (xn, yn)} could not have a convergent subsequence, so T (Br,XY ) would...

Bé nyi, Á rpá d; Torres, Rodolfo H.

2013-07-01T23:59:59.000Z

198

The Cooling of Compact Stars  

E-Print Network [OSTI]

The cooling of a compact star depends very sensitively on the state of dense matter at supranuclear densities, which essentially controls the neutrino emission, as well as on the structure of the stellar outer layers which control the photon emission. Open issues concern the hyperon population, the presence of meson condensates, superfluidity and superconductivity, and the transition of confined hadronic matter to quark matter. This paper describes these issues and presents cooling calculations based on a broad collection of equations of state for neutron star matter and strange matter. These results are tested against the body of observed cooling data.

Dany Page; Ulrich Geppert; Fridolin Weber

2005-08-01T23:59:59.000Z

199

Compact submanifolds supporting singular interactions  

SciTech Connect (OSTI)

A quantum particle moving under the influence of singular interactions on embedded surfaces furnish an interesting example from the spectral point of view. In these problems, the possible occurrence of a bound-state is perhaps the most important aspect. Such systems can be introduced as quadratic forms and generically they do not require renormalization. Yet an alternative path through the resolvent is also beneficial to study various properties. In the present work, we address these issues for compact surfaces embedded in a class of ambient manifolds. We discover that there is an exact bound state solution written in terms of the heat kernel of the ambient manifold for a range of coupling strengths. Moreover, we develop techniques to estimate bounds on the ground state energy when several surfaces, each of which admits a bound state solution, coexist. -- Highlights: Schrdinger operator with singular interactions supported on compact submanifolds. Exact bound-state solution in terms of the heat kernel of the ambient manifold. Generalization of the variational approach to a collection of submanifolds. Existence of a lower bound for a unique ground state energy.

Kaynak, Burak Tevfik, E-mail: burak.kaynak@boun.edu.tr; Teoman Turgut, O., E-mail: turgutte@boun.edu.tr

2013-12-15T23:59:59.000Z

200

Compacted carbon for electrochemical cells  

DOE Patents [OSTI]

This invention provides compacted carbon that is useful in the electrode of an alkali metal/carbon electrochemical cell of improved capacity selected from the group consisting of: (a) coke having the following properties: (1) an x-ray density of at least 2.00 grams per cubic centimeters, (2) a closed porosity of no greater than 5%, and (3) an open porosity of no greater than 47%; and (b) graphite having the following properties: (1) an x-ray density of at least 2.20 grams per cubic centimeters, (2) a closed porosity of no greater than 5%, and (3) an open porosity of no greater than 25%. This invention also relates to an electrode for an alkali metal/carbon electrochemical cell comprising compacted carbon as described above and a binder. This invention further provides an alkali metal/carbon electrochemical cell comprising: (a) an electrode as described above, (b) a non-aqueous electrolytic solution comprising an organic aprotic solvent and an electrolytically conductive salt and an alkali metal, and (c) a counter electrode. 10 figs.

Greinke, R.A.; Lewis, I.C.

1997-10-14T23:59:59.000Z

Note: This page contains sample records for the topic "incandescent compact fluorescent" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Hydrostatic compaction of Microtherm HT.  

SciTech Connect (OSTI)

Two samples of jacketed Microtherm{reg_sign}HT were hydrostatically pressurized to maximum pressures of 29,000 psi to evaluate both pressure-volume response and change in bulk modulus as a function of density. During testing, each of the two samples exhibited large irreversible compactive volumetric strains with only small increases in pressure; however at volumetric strains of approximately 50%, the Microtherm{reg_sign}HT stiffened noticeably at ever increasing rates. At the maximum pressure of 29,000 psi, the volumetric strains for both samples were approximately 70%. Bulk modulus, as determined from hydrostatic unload/reload loops, increased by more than two-orders of magnitude (from about 4500 psi to over 500,000 psi) from an initial material density of {approx}0.3 g/cc to a final density of {approx}1.1 g/cc. An empirical fit to the density vs. bulk modulus data is K = 492769{rho}{sup 4.6548}, where K is the bulk modulus in psi, and {rho} is the material density in g/cm{sup 3}. The porosity decreased from 88% to {approx}20% indicating that much higher pressures would be required to compact the material fully.

Broome, Scott Thomas; Bauer, Stephen J.

2010-09-01T23:59:59.000Z

202

Method for preparing porous metal hydride compacts  

DOE Patents [OSTI]

A method for preparing porous metallic-matrix hydride compacts which can be repeatedly hydrided and dehydrided without disintegration. A mixture of a finely divided metal hydride and a finely divided matrix metal is contacted with a poison which prevents the metal hydride from dehydriding at room temperature and atmospheric pressure. The mixture of matrix metal and poisoned metal hydride is then compacted under pressure at room temperature to form porous metallic-matrix hydride compacts.

Ron, M.; Gruen, D.M.; Mendelsohn, M.H.; Sheft, I.

1980-01-21T23:59:59.000Z

203

Method for preparing porous metal hydride compacts  

DOE Patents [OSTI]

A method for preparing porous metallic-matrix hydride compacts which can be repeatedly hydrided and dehydrided without disintegration. A mixture of a finely divided metal hydride and a finely divided matrix metal is contacted with a poison which prevents the metal hydride from dehydriding at room temperature and atmospheric pressure. The mixture of matrix metal and poisoned metal hydride is then compacted under pressure at room temperature to form porous metallic-matrix hydride compacts.

Ron, Moshe (Haifa, IL); Gruen, Dieter M. (Downers Grove, IL); Mendelsohn, Marshall H. (Woodridge, IL); Sheft, Irving (Oak Park, IL)

1981-01-01T23:59:59.000Z

204

On compact generation of deformed schemes.  

E-Print Network [OSTI]

We obtain a theorem which allows to prove compact generation of derived categories of Grothendieck categories, based upon certain coverings by localizations. This theorem follows from an application of Rouquier's cocovering theorem in the triangulated context, and it implies Neeman's result on compact generation of quasi-compact separated schemes. We prove an application of our theorem to non-commutative deformations of such schemes, based upon a change from Koszul complexes to Chevalley-Eilenberg complexes.

Wendy Lowen; Michel Van den Bergh

205

Nuclear Resonance Fluorescence for Materials Assay  

E-Print Network [OSTI]

clandestine material with nuclear resonance fluorescence.E. Norman, UC Berkeley Dept. of Nuclear Engineering, privatepp. 349. G. Warren et al. Nuclear Resonance Fluorescence of

Quiter, Brian

2010-01-01T23:59:59.000Z

206

Design and applications of a flicker voltage generator  

SciTech Connect (OSTI)

In this paper, a 200W flicker voltage generator is made by using microcomputers and linear amplification circuits. The modulation amplitudes and frequencies based on the UIE {Delta}V{sub 10} evaluation can be arbitrarily assigned by software with high accuracy. The flicker voltage signals measured at the customer side also can be re-generated. Some applications, such as evaluating the effects of flicker voltage on incandescent and compact fluorescent lamps (CFLs), are also made. From experimental tests by use of the flicker voltage generator, the properties of some compact fluorescent lamps and incandescent lamps are compared. Those properties describe the relation between input voltage variation and output flux of lamps, such that there is direct description of influences of flicker voltages on lamps.

Chang, W.N.; Wu, C.J. [National Taiwan Inst. of Tech., Peitow-Taipei (Taiwan, Province of China). Dept. of Electrical Engineering

1995-12-31T23:59:59.000Z

207

Interstate Mining Compact Commission (multi-state)  

Broader source: Energy.gov [DOE]

The Interstate Mining Compact is a multi-state governmental agency / organization that represents the natural resource and related environmental protection interests of its member states. Currently...

208

Convolution type operators on locally compact groups  

E-Print Network [OSTI]

Shtein--~erg, Convolution Type Operators on Locally Compact Groups [in Russian],. Manuscript Deposited in the All-Union Institute of Scientific and Technical...

209

Compact Solid State Cooling Systems: Compact MEMS Electrocaloric Module  

SciTech Connect (OSTI)

BEETIT Project: UCLA is developing a novel solid-state cooling technology to translate a recent scientific discovery of the so-called giant electrocaloric effect into commercially viable compact cooling systems. Traditional air conditioners use noisy, vapor compression systems that include a polluting liquid refrigerant to circulate within the air conditioner, absorb heat, and pump the heat out into the environment. Electrocaloric materials achieve the same result by heating up when placed within an electric field and cooling down when removedeffectively pumping heat out from a cooler to warmer environment. This electrocaloric-based solid state cooling system is quiet and does not use liquid refrigerants. The innovation includes developing nano-structured materials and reliable interfaces for heat exchange. With these innovations and advances in micro/nano-scale manufacturing technologies pioneered by semiconductor companies, UCLA is aiming to extend the performance/reliability of the cooling module.

None

2010-10-01T23:59:59.000Z

210

DOE/LX/07-0087&D1 Secondary Document DMSA C-333-41 Solid Waste...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

included welding rods, solder, a Nissen metal marker, fluorescent light starters, incandescent light bulbs and ends, fluorescent light bulb ends, miscellaneous lead pieces, and...

211

JY Tsao Evolution of Solid-State Lighting: Market Pull and Technology Push Xiamen 2005 Apr 13 Evolution of Solid-State Lighting  

E-Print Network [OSTI]

and Technology Push · Xiamen · 2005 Apr 13 0 20 40 60 80 100 0.1 1.0 10.0 100.0 Incandescent (12%) Fluorescent Fluorescent Standard Incandescent · So let's start with traditional lighting. · Here, I've plotted the 26 and Eugene Hong of Navigant Consulting. The lamps fall into three overall families: incandescent, in green

212

Solid-State lighting ReSeaRch & development at Sandia national laboRatoRieS  

E-Print Network [OSTI]

illumination via interface with microelectronics. MASSIVE ENERGY SAVINGS Incandescent and fluorescent lamps% efficient. Today's commercially available white LEDs are already five times as efficient as incandescent--or 10-15 times that of incandescent bulbs and 2-3 times that of fluorescents. BIG BOTTOM-LINE PAYOFF

213

Article #11, May 23, 2006 AJ's Technical Tips: Technologies for Lighting in Rural Africa  

E-Print Network [OSTI]

/a 30 lumens 0.1 Incandescent Bulb 15 W 225 lumens 15 Fluorescent Tube Lamp 10 W 500 lumens 50 White LED Lamp 1 W 30 lumens 30 The data in Table 1 show that incandescent bulbs and fluorescent tubes generate incandescent bulbs are about 150 times more efficient. In other words, electric lights are not only brighter

Jacobson, Arne

214

Compacted Soil Liner Interface Strength Importance  

E-Print Network [OSTI]

Case Study Compacted Soil Liner Interface Strength Importance Timothy D. Stark, F.ASCE1 ; Hangseok interface is not the geomembrane (GM)/compacted low-permeability soil liner (LPSL) but a soilsoil interface placing the cover soil from bottom to top. DOI: 10.1061/(ASCE)GT.1943-5606 .0000556. 2012 American

215

Non-compact versions of Edwards' Theorem  

E-Print Network [OSTI]

Edwards' Theorem establishes duality between a convex cone in the space of continuous functions on a compact space and the set of representing or Jensen measures for this cone. In this paper we prove non-compact versions of this theorem.

Gogus, Nihat G; Poletsky, Evgeny A

2010-01-01T23:59:59.000Z

216

3D N = 4 Gauge Theory Compactication  

E-Print Network [OSTI]

Outline 3D N = 4 Gauge Theory Compactication Twistors 3D N = 4 Supersymmetric Gauge Theories and Hyperk¨ahler Metrics Richard Eager UCSB Friday, October 17th, 2008, 4:00 p.m. Richard Eager UCSB 3D N = 4 Supersymmetric Gauge Theories and Hyperk¨ahler M #12;Outline 3D N = 4 Gauge Theory Compactication Twistors

Bigelow, Stephen

217

GREEN FLUORESCENT PROTEIN The green revolution  

E-Print Network [OSTI]

GREEN FLUORESCENT PROTEIN The green revolution Green fluorescent protein allows gene expression a fluorescent product when expressed. Just such a molecule, green fluorescent protein (GFP), has recently green light when disturbed (often seen when riding in a boat at night). In Aequorea, the green

Stearns, Tim

218

Nuclear Resonance Fluorescence for Nuclear Materials Assay  

E-Print Network [OSTI]

Potential of Nuclear Resonance Fluorescence . . . . . . . .2.9.1 Nuclear ThomsonSections . . . . . . . . . . . . . . . Nuclear Resonance

Quiter, Brian Joseph

2010-01-01T23:59:59.000Z

219

September 2007 21 commonplace," predicted Shinichiro  

E-Print Network [OSTI]

enough and their lifetime is longer than those of conventional incandescent lamps and fluorescent lights." Also, he noted, LEDs' power efficiency is greater than that of incandescent lamps and about same

Lu, Chenyang

220

Radioactivity-Synchronized Fluorescence Enhancement Using a Radionuclide Fluorescence-Quenched Dye  

E-Print Network [OSTI]

Radioactivity-Synchronized Fluorescence Enhancement Using a Radionuclide Fluorescence-Quenched Dye that demonstrates the feasibility of altering the fluorescence properties of an organic dye as a function effect on the dye fluorescence. Correlation of the radionuclide decay with the dye fluorescence

Larson-Prior, Linda

Note: This page contains sample records for the topic "incandescent compact fluorescent" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

National Compact Stellarator Experiment Project Closeout Report PROJECT CLOSEOUT REPORT  

E-Print Network [OSTI]

National Compact Stellarator Experiment Project Closeout Report i PROJECT CLOSEOUT REPORT NATIONAL of Science Princeton Plasma Physics Laboratory Oak Ridge National Laboratory #12;National Compact Stellarator Experiment Project Closeout Report PROJECT CLOSEOUT REPORT NATIONAL COMPACT STELLARATOR EXPERIMENT (NCSX

Princeton Plasma Physics Laboratory

222

Ceramic Mugs & Dishes Incandescent Light Bulbs  

E-Print Network [OSTI]

, MU East Rock Hall/19-B CELL PHONES - EYEGLASSES 654 Minnesota Street Room 208, copy room CVRI Helen. Zion Cancer Research Building N423 Parnassus Campus: eyeglasses "I" level, Optometry Store, MU West

Yamamoto, Keith

223

Energy-Saving Incandescents | Department of Energy  

Office of Environmental Management (EM)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) " ,"ClickPipelinesProvedDecember 2005DepartmentDecember 2011District |Department

224

Energy-Saving Incandescents | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:Year in Review: TopEnergyIDIQBusinessinSupporting JobsClean EnergyAcross U.S. Industry

225

A compact tritium AMS system  

SciTech Connect (OSTI)

Tritium ({sup 3}H) is a radioisotope that is extensively utilized in biological and environmental research. For biological research, {sup 3}H is generally quantified by liquid scintillation counting requiring gram-sized samples and counting times of several hours. For environmental research, {sup 3}H is usually quantified by {sup 3}He in-growth which requires gram-sized samples and in-growth times of several months. In contrast, provisional studies at LLNL's Center for Accelerator Mass Spectrometry have demonstrated that Accelerator Mass Spectrometry (AMS) can be used to quantify {sup 3}H in milligram-sized biological samples with a 100 to 1000-fold improvement in detection limits when compared to scintillation counting. This increased sensitivity is expected to have great impact in the biological and environmental research community. However in order to make the {sup 3}H AMS technique more broadly accessible, smaller, simpler, and less expensive AMS instrumentation must be developed. To meet this need, a compact, relatively low cost prototype {sup 3}H AMS system has been designed and built based on a LLNL ion source/sample changer and an AccSys Technology, Inc. Radio Frequency Quadrupole (RFQ) linac. With the prototype system, {sup 3}/{sup 1}H ratios ranging from 1 x 10{sup -10} to 1 x 10{sup -13} have to be measured from milligram sized samples. With improvements in system operation and sample preparation methodology, the sensitivity limit of the system is expected to increase to approximately 1 x 10{sup -15}.

Chiarappa, M L; Dingley, K H; Hamm, R W; Love, A H; Roberts, M L

1999-09-23T23:59:59.000Z

226

Compact, electro-hydraulic, variable valve actuation system providing...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Compact, electro-hydraulic, variable valve actuation system providing variable lift, timing and duration to enable high efficiency engine combustion control Compact,...

227

Development of Compact Gaseous Sensors with Internal Reference...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Compact Gaseous Sensors with Internal Reference for Monitoring O2 and NOx in Combustion Environments Development of Compact Gaseous Sensors with Internal Reference for Monitoring...

228

Micro- & Nano-Technologies Enabling More Compact, Lightweight...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Micro- & Nano-Technologies Enabling More Compact, Lightweight Thermoelectric Power Generation & Cooling Systems Micro- & Nano-Technologies Enabling More Compact, Lightweight...

229

DOE Withdraws the Energy Star Label from 34 Compact Fluorescent Light Bulbs  

Broader source: Energy.gov (indexed) [DOE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "ofEarly Career Scientists'Montana. DOCUMENTSof EnergyAlliance |Department ofShowerheads | Department|

230

High Hats, Swiss Cheese, and Fluorescent Lighting?  

SciTech Connect (OSTI)

For DOE, PNNL is conducting a competitive procurement to promote market introduction of new residential recessed downlights (also known as ''recessed cans'' or ''high hats'') that are airtight, rated for insulated ceilings, and hard-wired for CFLs. This paper discusses the potential energy savings of new high-efficiency downlights, and the results of product testing to date. Recessed downlights are the most popular residential lighting fixtures in the United States, with 21.7 million fixtures sold in 2000. An estimated 350 million are currently installed in American homes. Recessed cans are relatively inexpensive, and provide an unobtrusive, directed source of light for kitchens, hallways, and living rooms. Recessed cans are energy-intensive in three ways. First, virtually all recessed cans currently installed in the residential sector use incandescent light sources, typically reflector-type lamps drawing 65-150 watts. Second, heat from incandescent lamps adds to air-conditioning loads. Third, most installed recessed cans are not airtight, so they allow conditioned air to escape from the living area into unconditioned spaces such as attics. Addressing both lighting energy use and air leakage in recessed cans has proven challenging. Lighting energy efficiency is greatly improved by using CFLs. Air leakage can be addressed by making fixtures airtight. But when CFLs are used in an airtight recessed can, heat generated by the lamp and ballast is trapped within the fixture. Excessive heat causes reduced light output and shorter lifespan of the CFL. The procurement was designed to overcome these technical challenges and make new products available in the marketplace.

McCullough, Jeffrey J.; Gordon, Kelly L.

2002-08-30T23:59:59.000Z

231

Steady state compact toroidal plasma production  

DOE Patents [OSTI]

Apparatus and method for maintaining steady state compact toroidal plasmas. A compact toroidal plasma is formed by a magnetized coaxial plasma gun and held in close proximity to the gun electrodes by applied magnetic fields or magnetic fields produced by image currents in conducting walls. Voltage supply means maintains a constant potential across the electrodes producing an increasing magnetic helicity which drives the plasma away from a minimum energy state. The plasma globally relaxes to a new minimum energy state, conserving helicity according to Taylor's relaxation hypothesis, and injecting net helicity into the core of the compact toroidal plasma. Controlling the voltage so as to inject net helicity at a predetermined rate based on dissipative processes maintains or increases the compact toroidal plasma in a time averaged steady state mode.

Turner, William C. (Livermore, CA)

1986-01-01T23:59:59.000Z

232

Belle Fourche River Compact (South Dakota)  

Broader source: Energy.gov [DOE]

The Belle Fourche River Compact, agreed to by South Dakota and Wyoming, seeks to provide for the most efficient use of the waters of the Belle Fourche River Basin for multiple purposes, and to...

233

NONEXISTENCE OF ARITHMETIC FAKE COMPACT HERMITIAN ...  

E-Print Network [OSTI]

? of G is a fake compact hermitian symmetric space, or a fake Xu, if its Betti ...... Letting A = (2?)16/4320 and using the bounds (13) and (22), we conclude that.

2011-06-17T23:59:59.000Z

234

Gravitational waves from merging compact binaries  

E-Print Network [OSTI]

Largely motivated by the development of highly sensitive gravitational-wave detectors, our understanding of merging compact binaries and the gravitational waves they generate has improved dramatically in recent years. ...

Hughes, Scott A.

235

Fluorescent Lighting | Department of Energy  

Office of Environmental Management (EM)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "of Energy Power.pdf Flash2006-14.pdfattachment.pdf6.pdf5.pdfFluorescent Lighting Fluorescent Lighting

236

Stuck-at-fault test set compaction  

E-Print Network [OSTI]

. Test set size under pattern score based dynamic compaction . . . 13 . . . 17 Figure 7. Pattern Score distribution v:ith pattern metric dynamic compaction. . . . . . . . . . . . . . I g LIST OF TABLES Page Table l. l. nuit Target Sclcction Methods.... Fault Target Selection Methods Random Minimum Detection Count Circuit Name c432 c499 c880 c1355 c1908 G2670 Excitation Balance 0. 136296 0. 191652 0. 170293 0. 173310 0. 187486 0. 190484 Pattern Count 1152 873 2693 1394 1708 5148...

Vanfickell, Jason Michael

2013-02-22T23:59:59.000Z

237

Critical considerations of pupil alignment to achieve open-loop control of MEMS deformable mirror in non-linear laser scanning fluorescence  

E-Print Network [OSTI]

mechanism of the MEMS DM, a high resolution CMOS camera and a compact Shack-Hartmann wavefront sensor-Hartmann wavefront sensor 1. INTRODUCTION Nonlinear fluorescence microscopic imaging, with its unique advantages of intrinsic three dimensional optical sectioning ability, deep tissue penetration, and reduced photo

238

Covered Product Category: Fluorescent Ballasts  

Broader source: Energy.gov [DOE]

FEMP provides acquisition guidance and Federal efficiency requirements across a variety of product categories, including fluorescent ballasts, which are a FEMP-designated product category. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

239

Covered Product Category: Fluorescent Luminaires  

Broader source: Energy.gov [DOE]

FEMP provides acquisition guidance and Federal efficiency requirements across a variety of product categories, including fluorescent luminaires. Federal laws and requirements mandate that agencies meet these efficiency requirements in all procurement and acquisition actions that are not specifically exempted by law.

240

Soil Quality Information Sheet Rangeland Soil Quality--Compaction  

E-Print Network [OSTI]

Soil Quality Information Sheet Rangeland Soil Quality--Compaction USDA, Natural Resources Conservation Service May 2001 Rangeland Sheet 4 What is compaction? Soil compaction occurs when moist or wet soil aggregates are pressed together and the pore space between them is reduced. Compaction changes

Note: This page contains sample records for the topic "incandescent compact fluorescent" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Compact Proof Certificates For Linear Logic Kaustuv Chaudhuri  

E-Print Network [OSTI]

Compact Proof Certificates For Linear Logic Kaustuv Chaudhuri INRIA, France http://kaustuv.chaudhuri

Chaudhuri, Kaustuv

242

Capacitive sensing with a fluorescent lamp  

E-Print Network [OSTI]

This work presents a modified fluorescent lamp that can be used as a capacitive sensing system. The lamp sensor measures changes in the electric fields emitted from the fluorescent bulbs in order to deduce the presence and ...

Cooley, John Jacob

2007-01-01T23:59:59.000Z

243

Phased array compaction cell for measurement of the transversely isotropic elastic properties of compacting sediments  

SciTech Connect (OSTI)

Sediments undergoing compaction typically exhibit transversely isotropic (TI) elastic properties. We present a new experimental apparatus, the phased array compaction cell, for measuring the TI elastic properties of clay-rich sediments during compaction. This apparatus uses matched sets of P- and S-wave ultrasonic transducers located along the sides of the sample and an ultrasonic P-wave phased array source, together with a miniature P-wave receiver on the top and bottom ends of the sample. The phased array measurements are used to form plane P-waves that provide estimates of the phase velocities over a range of angles. From these measurements, the five TI elastic constants can be recovered as the sediment is compacted, without the need for sample unloading, recoring, or reorienting. This paper provides descriptions of the apparatus, the data processing, and an application demonstrating recovery of the evolving TI properties of a compacting marine sediment sample.

Nihei, K.T.; Nakagawa, S.; Reverdy, F.; Meyer, L.R.; Duranti, L.; Ball, G.

2010-12-15T23:59:59.000Z

244

Strategy Guideline: Compact Air Distribution Systems  

SciTech Connect (OSTI)

This Strategy Guideline discusses the benefits and challenges of using a compact air distribution system to handle the reduced loads and reduced air volume needed to condition the space within an energy efficient home. Traditional systems sized by 'rule of thumb' (i.e., 1 ton of cooling per 400 ft2 of floor space) that 'wash' the exterior walls with conditioned air from floor registers cannot provide appropriate air mixing and moisture removal in low-load homes. A compact air distribution system locates the HVAC equipment centrally with shorter ducts run to interior walls, and ceiling supply outlets throw the air toward the exterior walls along the ceiling plane; alternatively, high sidewall supply outlets throw the air toward the exterior walls. Potential drawbacks include resistance from installing contractors or code officials who are unfamiliar with compact air distribution systems, as well as a lack of availability of low-cost high sidewall or ceiling supply outlets to meet the low air volumes with good throw characteristics. The decision criteria for a compact air distribution system must be determined early in the whole-house design process, considering both supply and return air design. However, careful installation of a compact air distribution system can result in lower material costs from smaller equipment, shorter duct runs, and fewer outlets; increased installation efficiencies, including ease of fitting the system into conditioned space; lower loads on a better balanced HVAC system, and overall improved energy efficiency of the home.

Burdick, A.

2013-06-01T23:59:59.000Z

245

Inside this issue: Green Dorm,  

E-Print Network [OSTI]

. The crew, which we call the Green Scene team, will be changing out incandescent light bulbs for compact (see page 1). The incandescent bulbs collected will be donated to a local organization. Prizes will be given to the person who returns the most incandescent bulbs. CFL's use one-third of the energy than

Kidd, William S. F.

246

Cylindrically Symmetric Models of Anisotropic Compact Stars  

E-Print Network [OSTI]

In this paper we have discussed the possibility of forming anisotropic compact stars from cosmological constant as one of the competent candidates of dark energy with cylindrical symmetry. For this purpose, we have applied the analytical solution of Krori and Barua metric to a particular cylindrically symmetric spacetime. The unknown constants in Krori and Barua metric have been determined by using masses and radii of class of compact stars like 4$U$1820-30, Her X-1, SAX J 1808-3658. The properties of these stars have been analyzed in detail. In this setting the cosmological constant has been taken as a variable which depends on the radial coordinates. We have checked all the regularity conditions, stability and surface redshift of the compact stars 4$U$1820-30, Her X-1, SAX J 1808-3658.

G. Abbas; Sumara Nazeer; M. A. Meraj

2014-12-16T23:59:59.000Z

247

Remote vacuum compaction of compressible hazardous waste  

DOE Patents [OSTI]

A system for remote vacuum compaction and containment of low-level radioactive or hazardous waste comprising a vacuum source, a sealable first flexible container, and a sealable outer flexible container for receiving one or more first flexible containers. A method for compacting low level radioactive or hazardous waste materials at the point of generation comprising the steps of sealing the waste in a first flexible container, sealing one or more first containers within an outer flexible container, breaching the integrity of the first containers, evacuating the air from the inner and outer containers, and sealing the outer container shut.

Coyne, Martin J. (Pittsburgh, PA); Fiscus, Gregory M. (McMurray, PA); Sammel, Alfred G. (Pittsburgh, PA)

1998-01-01T23:59:59.000Z

248

Remote vacuum compaction of compressible hazardous waste  

DOE Patents [OSTI]

A system is described for remote vacuum compaction and containment of low-level radioactive or hazardous waste comprising a vacuum source, a sealable first flexible container, and a sealable outer flexible container for receiving one or more first flexible containers. A method for compacting low level radioactive or hazardous waste materials at the point of generation comprising the steps of sealing the waste in a first flexible container, sealing one or more first containers within an outer flexible container, breaching the integrity of the first containers, evacuating the air from the inner and outer containers, and sealing the outer container shut. 8 figs.

Coyne, M.J.; Fiscus, G.M.; Sammel, A.G.

1998-10-06T23:59:59.000Z

249

Supplementary Material for: Application of Synchrotron Radiation for Measurement of Iron Red-ox  

E-Print Network [OSTI]

@engr.wisc.edu #12;Incandescent Light Bulb Spectrum Figure 1 Visible Light Fluorescent Light Bulb Spectrum #12;Figure 2 Visible Light Incandescent Light Bulb Spectrum #12;Figure 3 Unmodified XANES Spectrum February 14 of the incandescent lights used for aging the atmospheric aerosols. The units are in m / S / m2 / nm. Figure 3

Meskhidze, Nicholas

250

How Many CASTLE Bulbs Would You Need To Match the Brightness of the Sun?  

E-Print Network [OSTI]

;Suppose that you have two household incandescent bulbs: one is labeled "60W," the other "100W." If you try incandescent bulb and a 9W fluorescent bulb. Which one makes your room brighter? It's not what you might expect... in fact, they look about the same! The incandescent bulb emits a broad spectrum of visible and infrared

Collar, Juan I.

251

PipelineJuly 2012 Volume 4, Issue 4 (From President Kaler's June 14 e-mail)  

E-Print Network [OSTI]

the LightEnergy Management seeks incandescent and T12 lamps Energy Management Senior Engineer Alicia inefficient light sources. Although the vast majority of the campus's number one offenders -- incandescent fluorescent lamps and classic incandescent A-lamps. T12's can be identified by their "fat" appearance (1

Webb, Peter

252

Phys. Med. Biol. 43 (1998) 24072412. Printed in the UK PII: S0031-9155(98)90934-4 Effects of read-out light sources and ambient light on  

E-Print Network [OSTI]

laser, light emitting diode (LED) and incandescent read-out light sources produce an equivalent dose, fluorescent light and incandescent ambient light produce an equivalent dose coloration of 30 cGy h-1, 18 cGy h the optical density of Gafchromic films include, helium neon lasers, ultrabright diodes, incandescent

Yu, K.N.

253

Compact range for variable-zone measurements  

DOE Patents [OSTI]

A compact range for testing antennas or radar targets includes a source for directing energy along a feedline toward a parabolic reflector. The reflected wave is a spherical wave with a radius dependent on the distance of the source from the focal point of the reflector.

Burnside, Walter D. (Columbus, OH); Rudduck, Roger C. (Columbus, OH); Yu, Jiunn S. (Albuquerque, NM)

1988-01-01T23:59:59.000Z

254

Compact Ultradense Objects in the Solar System  

E-Print Network [OSTI]

We describe properties and gravitational interactions of meteor-mass and greater compact ultra dense objects with nuclear density or greater (CUDO s). We discuss possible enclosure of CUDO s in comets, stability of these objects on impact with the Earth and Sun and show that the hypothesis of a CUDO core helps resolve issues challenging the understanding of a few selected cometary impacts.

J. Rafelski; Ch. Dietl; L. Labun

2013-03-19T23:59:59.000Z

255

A Global Compact to End Poverty  

E-Print Network [OSTI]

A Global Compact to End Poverty Jeffrey Sachs on stabilisation, transition and weapons of mass progress. We can realistically envision a world without extreme poverty by the year 2025 because. Sachs, The End of Poverty, 2005. WORLD ECONOMICS Vol. 6 No. 4 OctoberDecember 2005 11 Jeffrey D

256

Physics of compact stellarators* S. P. Hirshman,  

E-Print Network [OSTI]

Physics of compact stellarators* S. P. Hirshman, D. A. Spong, J. C. Whitson, B. Nelson, D. B. Redi, W. Reiersen, A. H. Reiman, J. Schmidt, R. White, and M. C. Zarnstorff Princeton Plasma Physics, Austin, Texas 78712-1081 A. Boozer Department of Applied Physics, Columbia University, New York, New York

257

Peak Power Reduction Strategies for the Lighting Systems in Government Buildings  

E-Print Network [OSTI]

PEAK POWER REDUCTION STRATEGIES FOT THE LIGHTING SYSTEMS IN GOVERNMENT BUILDINGS Dina AlNakib CLEP, Dr. Ahmad Al-Mulla CEM, Gopal Maheshwari Department of Building and Energy Technologies Environment and Urban Development Division Kuwait... begins at 7:30 h and ends between 14:00 and 15:30 h. Lighting systems in MC building comprise mostly of T12 fluorescent tubes with magnetic ballasts, compact fluorescent lamps (CFLs) and incandescent lamps with a total connected load of 2,900 k...

Al-Nakib, D.; Al-Mulla, A. A.; Maheshwari, G. P.

2010-01-01T23:59:59.000Z

258

Southeast Interstate Low-Level Radioactive Waste Management Compact (multi-state)  

Broader source: Energy.gov [DOE]

The Southeast Interstate Low-Level Radioactive Waste Management Compact is administered by the Compact Commission. The Compact provides for rotating responsibility for the region's low-level...

259

Engineering properties of miniature cement - fly ash compacts prepared by high pressure compaction  

E-Print Network [OSTI]

ENGINEERING PROPERTIES OF MINIATURE CEMENT - FLY ASH COMPACTS PREPARED BY HIGH PRESSURE COMPACTION E NGIRPR OT SFMMAFU AEU C-ALEYY HDOBPvvIi va vGI ge(iD(vI oannItI au NId(R E)L xrP1IeRPvT 9(evP(n uDnuPnnBIrv au vGI eI0DPeIBIrvR uae vGI i...IteII au LEHNFA -M Ho2FYoF EDtDRv 3456 L(7ae HDO7I8v? oP1Pn FrtPrIIePrt ENGINEERING PROPERTIES OF MINIATURE CEMENT - FLY ASH COMPACTS PREPARED BY HIGH PRESSURE COMPACTION E NGIRPR OT SFMMAFU AEU C-ALEYY E99ea1Ii (R va RvTnI (ri 8arvIrv OT? LP...

Bormann, Jeffrey Ray

1985-01-01T23:59:59.000Z

260

Chromosome characterization using single fluorescent dye  

DOE Patents [OSTI]

Chromosomes are characterized by fluorescent emissions from a single fluorescent dye that is excited over two different wavelengths. A mixture containing chromosomes is stained with a single dye selected from the group consisting of TOTO and YOYO and the stained chromosomes are placed in a flow cytometer. The fluorescent dye is excited sequentially by a first light having a wavelength in the ultraviolet range to excite the TOTO or YOYO to fluoresce at a first intensity and by a second light having a wavelength effective to excite the TOTO or YOYO dye to fluoresce at a second intensity. Specific chromosomes may be identified and sorted by intensity relationships between the first and second fluorescence emissions.

Crissman, Harry A. (Los Alamos, NM); Hirons, Gregory T. (Irvine, CA)

1995-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "incandescent compact fluorescent" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Saccharide sensing molecules having enhanced fluorescent properties  

DOE Patents [OSTI]

The present invention provides formulae for fluorescent compounds that have a number of properties which make them uniquely suited for use in sensors of analytes such as saccharides. The advantageous fluorescent properties include favorable excitation wavelengths, emission wavelengths, fluorescence lifetimes, and photostability. Additional advantageous properties include enhanced aqueous solubility, as well as temperature and pH sensitivity. The compound comprises an aryl or a substituted phenyl botonic acid that acts as a substrate recognition component, a fluorescence switch component, and a fluorophore. Fluorescent compounds are described that are excited at wavelengths greater than 400 nm and emit at wavelengths greater than 450 nm, which is advantageous for optical transmission through skin. The fluorophore is typically selected from transition metal-ligand complexes and thiazine, oxazine, oxazone, or oxazine-one as well as anthracene compounds. The fluorescent compound can be immobilized in a glucose permeable biocompatible polymer matrix that is implantable below the skin.

Satcher Jr., Joe H.; Lane, Stephen M.; Darrow, Christopher B.; Cary, Douglas R.; Tran, Joe Anh

2004-01-06T23:59:59.000Z

262

Fundamental building blocks for a compact optoelectronic neural network processor  

E-Print Network [OSTI]

The focus of this thesis is interconnects within the Compact Optoelectronic Neural Network Processor. The goal of the Compact Optoelectronic Neural Network Processor Project (CONNPP) is to build a small, rugged neural ...

Ruedlinger, Benjamin Franklin, 1976-

2003-01-01T23:59:59.000Z

263

Scanning fluorescent microthermal imaging apparatus and method  

DOE Patents [OSTI]

A scanning fluorescent microthermal imaging (FMI) apparatus and method is disclosed, useful for integrated circuit (IC) failure analysis, that uses a scanned and focused beam from a laser to excite a thin fluorescent film disposed over the surface of the IC. By collecting fluorescent radiation from the film, and performing point-by-point data collection with a single-point photodetector, a thermal map of the IC is formed to measure any localized heating associated with defects in the IC. 1 fig.

Barton, D.L.; Tangyunyong, P.

1998-01-06T23:59:59.000Z

264

Scanning fluorescent microthermal imaging apparatus and method  

DOE Patents [OSTI]

A scanning fluorescent microthermal imaging (FMI) apparatus and method is disclosed, useful for integrated circuit (IC) failure analysis, that uses a scanned and focused beam from a laser to excite a thin fluorescent film disposed over the surface of the IC. By collecting fluorescent radiation from the film, and performing point-by-point data collection with a single-point photodetector, a thermal map of the IC is formed to measure any localized heating associated with defects in the IC.

Barton, Daniel L. (Albuquerque, NM); Tangyunyong, Paiboon (Albuquerque, NM)

1998-01-01T23:59:59.000Z

265

December 2002 Issue #11 2002 IDENTIFYING AND MANAGING COMPACTION  

E-Print Network [OSTI]

of compaction The need to conduct field operations in a timely and efficient manner has given rise to concerns

Balser, Teri C.

266

A study of compaction methods for lunar soil simulants  

E-Print Network [OSTI]

, compaction by vibration, compaction under vacuum pressure under the simultaneous effect of vibration are examined. Duc to the increasing confining pressure, the air voids decrease and the particles will be more closely packed, thus increasing the relative... density. The research will be used to identify a convenient method for compacting samples for laboratory digging experiments. The results of the research conclude that compaction by using vacuum and vibration produce results which can be used to predict...

Ekkad, Rama Varadarajan

1993-01-01T23:59:59.000Z

267

Portable spotter for fluorescent contaminants on surfaces  

DOE Patents [OSTI]

A portable fluorescence-based spotter for polynuclear aromatic hydrocarbon contamination on personnel and work area surfaces under ambient lighting conditions is provided. This instrument employs beam modulation and phase sensitive detection for discriminating between fluorescence from organic materials from reflected background light and inorganic fluorescent material. The device uses excitation and emission filters to provide differentiation between classes of aromatic organic compounds. Certain inorganic fluorescent materials, including heavy metal compounds, may also be distinguished from the organic compounds, despite both having similar optical properties.

Schuresko, Daniel D. (Oak Ridge, TN)

1980-01-01T23:59:59.000Z

268

LED Replacements for Linear Fluorescent Lamps Webcast  

Broader source: Energy.gov [DOE]

In this June 20, 2011 webcast on LED products marketed as replacements for linear fluorescent lamps, Jason Tuenge of the Pacific Northwest National Laboratory (PNNL) discussed current Lighting...

269

High-performance CFL downlights: The best and the brightest  

SciTech Connect (OSTI)

Downlight fixtures -- often referred to as ``recessed cans`` -- are among the most common lighting fixtures in commercial and residential settings. As such, they represent one of the most promising targets for improving lighting energy efficiency. The authors estimate that downlight fixtures account for more than one-fifth of the 2.8 billion incandescent lighting sockets in the US, and represent about 8 percent of total direct lighting energy use. Over 30 million new fixtures of this type are sold each year in the US. With existing and foreseeable technology, nearly two-thirds of the incandescent downlights in the US are candidates for retrofit or replacement with compact fluorescent lamps (CFLs) or fixtures. The remaining one-third, however, are unlikely to ever be replaceable with CFL technology because of constraints on light output, lighting quality, size, and cost-effectiveness of CFL alternatives. High performance downlight systems using compact fluorescent lamps and incorporating advanced optical, thermal, and ballast designs use up to 75 percent less energy than conventional incandescent downlight fixtures. Many CFL downlight fixtures, however, perform poorly. In this report, the authors explore ways in which various elements of fixture design influence performance. They also describe exemplary elements of high-performance designs, and evaluate several emerging or experimental technologies that promise to further improve efficiency.

Sardinsky, R.; Hawthorne, S.; Newcomb, J.

1993-12-31T23:59:59.000Z

270

3-DIMENSIONAL COMPACT DISC (CD) MICROFLUIDIC PLATFORM Presented to the  

E-Print Network [OSTI]

3-DIMENSIONAL COMPACT DISC (CD) MICROFLUIDIC PLATFORM _______________ A Thesis Presented OF THE THESIS 3-Dimensional Compact Disc (CD) Microfluidic Platform by Nitin Edmund Harwood Master of Science in a compact disc (CD) microfluidics platform involving two or more layers. The traditional 2-Dimensional

Kassegne, Samuel Kinde

271

THE COMPACT STEEP SPECTRUM AND GHZ PEAKED SPECTRUM RADIO SOURCES  

E-Print Network [OSTI]

THE COMPACT STEEP SPECTRUM AND GHZ PEAKED SPECTRUM RADIO SOURCES Christopher P. O'Dea Space@stsci.edu ABSTRACT I review the radio to X­ray properties of GHz Peaked Spectrum (GPS) and Compact Steep Spectrum The GHz Peaked Spectrum (GPS) and Compact Steep Spectrum (CSS) radio sources make up significant fractions

272

Guide to Red Fluorescent Proteins and Biosensors for Flow Cytometry  

E-Print Network [OSTI]

CHAPTER 17 Guide to Red Fluorescent Proteins and Biosensors for Flow Cytometry Kiryl D. PiatkevichH Stability of Fluorescence F. Optimization of Nucleotide and Amino Acid Sequences III. Modern Advanced Red-Shifted FPs A. Orange Fluorescent Proteins B. Red Fluorescent Proteins C. Far-Red Fluorescent Proteins IV

Verkhusha, Vladislav V.

273

Electric holding company regulation by multistate compact  

SciTech Connect (OSTI)

This article is divided into five sections. The first section discusses the market and regulatory environment of bulk power sales. The second presents the legal framework for compacting and discusses the minimal constitutional barriers presented by the Compact Clause. The next section discusses the economic considerations inherent in attempting to regulate a national activity through regional authorities. The fourth section more fully develops the administrative and political problems that regional regulation must overcome to be successful. Using the legal, economic, and policy framework developed in the preceding sections, the final section analyzes the proposal encompassed in Senate Bill 2607, a proposal by the Arkansas Public Service Commission and Entergy Corporation to create regional organizations to provide integrated resource planning.

Darr, F.P.

1993-01-01T23:59:59.000Z

274

DEVELOPMENT OF A PRECISION TUNABLE GAMMA-RAY SOURCE DRIVEN BY A COMPACT X-BAND LINAC  

SciTech Connect (OSTI)

A precision, tunable gamma-ray source driven by a compact, high-gradient X-band linac is currently under development at LLNL. High-brightness, relativistic electron bunches produced by the linac interact with a Joule-class, 10 ps laser pulse to generate tunable {gamma}-rays in the 0.5-2.5 MeV photon energy range via Compton scattering. The source will be used to excite nuclear resonance fluorescence lines in various isotopes; applications include homeland security, stockpile science and surveillance, nuclear fuel assay, and waste imaging and assay. The source design, key parameters, and current status are presented.

Hartemann, F V; Albert, F; Anderson, G G; Anderson, S G; Bayramian, A J; Betts, S M; Chu, T S; Cross, R R; Ebbers, C A; Fisher, S E; Gibson, D J; Ladran, A S; Messerly, M J; Semenov, V A; Shverdin, M Y; Siders, C W; McNabb, D P; Barty, C J; Vlieks, A E; Jongewaard, E N; Tantawi, S G

2009-04-30T23:59:59.000Z

275

Orthonormal bases of compactly supported wavelets  

E-Print Network [OSTI]

Abstract. Several variations are given on the construction of orthonormal bases of wavelets with compact support. They have, respectively, more symmetry, more regularity, or more vanishing moments for the scaling function than the examples constructed in Daubechies [Comm. Pure Appl. Math., 41 (1988), pp. 909-996]. Key words, wavelets, orthonormal bases, regularity, symmetry AMS(MOS) subject classifications. 26A16, 26A18, 26A27, 39B12

Ingrid Daubechies

1988-01-01T23:59:59.000Z

276

Compact x-ray source and panel  

DOE Patents [OSTI]

A compact, self-contained x-ray source, and a compact x-ray source panel having a plurality of such x-ray sources arranged in a preferably broad-area pixelized array. Each x-ray source includes an electron source for producing an electron beam, an x-ray conversion target, and a multilayer insulator separating the electron source and the x-ray conversion target from each other. The multi-layer insulator preferably has a cylindrical configuration with a plurality of alternating insulator and conductor layers surrounding an acceleration channel leading from the electron source to the x-ray conversion target. A power source is connected to each x-ray source of the array to produce an accelerating gradient between the electron source and x-ray conversion target in any one or more of the x-ray sources independent of other x-ray sources in the array, so as to accelerate an electron beam towards the x-ray conversion target. The multilayer insulator enables relatively short separation distances between the electron source and the x-ray conversion target so that a thin panel is possible for compactness. This is due to the ability of the plurality of alternating insulator and conductor layers of the multilayer insulators to resist surface flashover when sufficiently high acceleration energies necessary for x-ray generation are supplied by the power source to the x-ray sources.

Sampayon, Stephen E. (Manteca, CA)

2008-02-12T23:59:59.000Z

277

The Evolution of Compact Binary Star Systems  

E-Print Network [OSTI]

We review the formation and evolution of compact binary stars consisting of white dwarfs (WDs), neutron stars (NSs), and black holes (BHs). Mergings of compact binary stars are expected to be the most important sources for the forthcoming gravitational-wave (GW) astronomy. In the first part of the review, we discuss observational manifestations of close binary stars with NS and/or black components and their merger rate, crucial points in the formation and evolution of compact stars in binary systems, including the treatment of the natal kicks which NSs and BHs acquire during the core collapse of massive stars and the common envelope phase of binary evolution, which are most relevant to the merging rates of NS-NS, NS-BH and BH-BH binaries. The second part of the review is devoted mainly to formation and evolution of binary WDs and their observational manifestations, including their role as progenitors of cosmologically important thermonuclear SN Ia. We also consider AM CVn-stars which are thought to be the best verification binary GW sources for future low-frequency GW space interferometers.

Konstantin Postnov; Lev Yungelson

2014-03-21T23:59:59.000Z

278

A laboratory investigation of vibratory compaction of dry soils  

E-Print Network [OSTI]

. Standard Compaction Curve for Soil 3 (CL) 48 49 50 53 54 56 25 Effect of Frequency Variation on the Time Required to Achieve I/2 inch (12. 7 mm) of Settlement 57 26. Foot Size Effects on Compaction of Various Soils 59 27. Effect of Frequency... on the Compaction of Soil 1 (SP) Using Two Different Feet 63 28. Effect of Frequency on the Compaction of Soil 1 (SP) Using the Semi-Circular Foot with Various Static Weights 64 29. Effect of Frequency on the Compaction of Soil 1 (SP) Using the 5 Inch Diameter...

Webster, Cecil Ray

1984-01-01T23:59:59.000Z

279

2014-12-30 Issuance: Energy Conservation Standard for General...  

Energy Savers [EERE]

2014-12-30 Issuance: Energy Conservation Standard for General Service Fluorescent Lamps and Incandescent Reflector Lamps; Final Rule 2014-12-30 Issuance: Energy Conservation...

280

2014-04-11 Issuance: Energy Conservation Standards for General...  

Broader source: Energy.gov (indexed) [DOE]

Energy Conservation Standards for General Service Fluorescent Lamps and Incandescent Reflector Lamps; Notice of Proposed Rulemaking 2014-04-11 Issuance: Energy Conservation...

Note: This page contains sample records for the topic "incandescent compact fluorescent" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Fabrication of color tunable organic light-emitting diodes by an alignment free mask patterning method  

E-Print Network [OSTI]

that of the incandescent bulb and comparable with that of the fluorescent tube. OLEDs are a true sur- face/area lighting

282

Semiconductor Science and Technology  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

controlled illumination via interface with microelectronics. MASSIVE ENERGY SAVINGS Incandescent and fluorescent lamps convert less than 20% of electrical energy into visible...

283

CX-003584: Categorical Exclusion Determination | Department of...  

Broader source: Energy.gov (indexed) [DOE]

community facilities and based on the results of the audits, change fixtures from incandescent to fluorescent lighting. In addition, the IRHA proposes to conduct mechanical...

284

DOE/LX/07-0242&D1 Secondary Document DMSA C-400-05 Solid Waste...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

fuses, three capacitors, three circuit boards, sixteen vacuum tubes, thirty-two incandescent light bulbs or fluorescent light bulbs, gallon of nitric acid, five aerosol...

285

--No Title--  

Broader source: Energy.gov (indexed) [DOE]

until funds are expended. Retrofits will consist of changing fixtures from incandescent to fluorescent lighting. Recent experience with lighting retrofits in the region...

286

CX-000139: Categorical Exclusion Determination | Department of...  

Broader source: Energy.gov (indexed) [DOE]

until funds are expended. Retrofits will consist of changing fixtures from incandescent to fluorescent lighting. Recent experience with lighting retrofits in the region...

287

EA-1664: Finding of No Significant Impact | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

Energy Conservation Standards: Energy Conservation Standards for Fluorescent and Incandescent Lamps The U.S. Department of Energy has determined that the adoption of energy...

288

Energy Efficiency and Conservation Block Grant Program  

Broader source: Energy.gov (indexed) [DOE]

community facilities and based on the results of the audits, change fixtures from incandescent to fluorescent lighting. In addition, the IRHA proposes to conduct mechanical...

289

Understanding Drooping Light Emitting Diodes CEEM | U.S. DOE...  

Office of Science (SC) Website

Impact Understanding "droop" may result in cheaper, more efficient LEDs; LEDs are more energy efficient, smaller, and longer-lived than incandescent lamps or fluorescent...

290

Buying an Appliance this Holiday Season? ENERGY STAR Products...  

Office of Environmental Management (EM)

Freezers Room air conditioners Televisions Clothes washers Dishwashers Battery chargers Water heaters Fluorescent lamp ballasts Incandescent reflector lamps If your appliance has...

291

A novel fluorescence detection method for organosilanes  

SciTech Connect (OSTI)

Quinones such as phenanthraquinone and anthraquinone react with organosilanes giving persistent, strongly fluorescent radicals. The reactions are photochemically initiated, rapid, and facile; detection of concentrations of silanes in the 10{sup {minus}7} M range are readily achieved. The staring materials do not fluorescence making the procedure simple, selective and specific.

Yang, H.X.; Craw, M.T.; Depew, M.C.; Wan, J.K.S. (Queen's Univ., Kingston, Ontario (Canada))

1989-02-01T23:59:59.000Z

292

Applications of Nuclear Resonance Fluorescence  

SciTech Connect (OSTI)

Nuclear Resonance Fluorescence (NRF) has the potential of addressing a wide variety of applications, which require isotopic and/or elemental information about a sample. We have investigated a variety of non-proliferation applications that may be addressed by NRF. From these applications, we have selected two, measuring uranium enrichment in UF6 cylinders and material verification in dismantlement, to investigate in more detail. Analytical models have been developed to evaluate these applications, and test measurements have been conducted to validate those models. We found that it is unlikely with current technology to address the requirements for UF6 cylinder enrichment measurements. In contrast, NRF is a very promising approach for material verification for dismantlement.

Warren, Glen A.; Detwiler, Rebecca S.; Peplowski, Patrick N.

2010-11-11T23:59:59.000Z

293

Excitation-emission spectra and fluorescence quantum yields for...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Excitation-emission spectra and fluorescence quantum yields for fresh and aged biogenic secondary organic aerosols. Excitation-emission spectra and fluorescence quantum yields for...

294

Hard X-ray Fluorescence Measurements of Heteroepitaxial Solid...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Hard X-ray Fluorescence Measurements of Heteroepitaxial Solid Oxide Fuel Cell Cathode Materials. Hard X-ray Fluorescence Measurements of Heteroepitaxial Solid Oxide Fuel Cell...

295

Comparison of Test Procedures and Energy Efficiency Criteria in Selected International Standards and Labeling Programs for Clothes Washers, Water Dispensers, Vending Machines and CFLs  

E-Print Network [OSTI]

top_runner//tr_fluorescent_light_bulb_jul.2009.pdf NiskinSubcommittee Final Report (bulb type fluorescent lamp). Fluorescent Lamps (CFLs) are an efficient lighting alternative to traditional incandescent light bulbs

Fridley, David

2010-01-01T23:59:59.000Z

296

Hiding patterns with daylight fluorescent inks  

E-Print Network [OSTI]

We propose a method for hiding patterns within printed images by making use of classical and of two daylight fluorescent magenta and yellow inks. Under the D65 illuminant we establish in the CIELAB space the gamut of a classical cmyk printer and the gamut of the same printer using a combination of classical inks with daylight fluorescent inks. These gamuts show that a significant part of the classical ink gamut can be reproduced by combining classical inks with daylight fluorescent inks. By printing parts of images with a combination of classical and daylight fluorescent inks instead of using classical inks only, we can hide security patterns within printed images. Under normal daylight, we do not see any difference between the parts printed with classical inks only and the parts printed with daylight fluorescent inks and classical inks. By changing the illumination, e.g. by viewing the printed image under a tungsten lamp or under a UV lamp, the daylight fluorescent inks change their colors and reveal the security pattern formed by combinations of classical inks and of daylight fluorescent inks.

Romain Rossier; Roger D. Hersch; School Of Computer; Communication Sciences; Ecole Polytechnique; Fdrale Lausanne

297

Glucose sensing molecules having selected fluorescent properties  

DOE Patents [OSTI]

An analyte sensing fluorescent molecule that employs intramolecular electron transfer is designed to exhibit selected fluorescent properties in the presence of analytes such as saccharides. The selected fluorescent properties include excitation wavelength, emission wavelength, fluorescence lifetime, quantum yield, photostability, solubility, and temperature or pH sensitivity. The compound comprises an aryl or a substituted phenyl boronic acid that acts as a substrate recognition component, a fluorescence switch component, and a fluorophore. The fluorophore and switch component are selected such that the value of the free energy for electron transfer is less than about 3.0 kcal mol.sup.-1. Fluorescent compounds are described that are excited at wavelengths greater than 400 nm and emit at wavelengths greater than 450 nm, which is advantageous for optical transmission through skin. The fluorophore is typically selected from transition metal-ligand complexes and thiazine, oxazine, oxazone, or oxazine-one as well as anthracene compounds. The fluorescent compound can be immobilized in a glucose permeable biocompatible polymer matrix that is implantable below the skin.

Satcher Jr., Joe H.; Lane, Stephen M.; Darrow, Christopher B.; Cary, Douglas R.; Tran, Joe Anh

2004-01-27T23:59:59.000Z

298

Raytheon's next generation compact inline cryocooler architecture  

SciTech Connect (OSTI)

Since the 1970s, Raytheon has developed, built, tested and integrated high performance cryocoolers. Our versatile designs for single and multi-stage cryocoolers provide reliable operation for temperatures from 10 to 200 Kelvin with power levels ranging from 50 W to nearly 600 W. These advanced cryocoolers incorporate clearance seals, flexure suspensions, hermetic housings and dynamic balancing to provide long service life and reliable operation in all relevant environments. Today, sensors face a multitude of cryocooler integration challenges such as exported disturbance, efficiency, scalability, maturity, and cost. As a result, cryocooler selection is application dependent, oftentimes requiring extensive trade studies to determine the most suitable architecture. To optimally meet the needs of next generation passive IR sensors, the Compact Inline Raytheon Stirling 1-Stage (CI-RS1), Compact Inline Raytheon Single Stage Pulse Tube (CI-RP1) and Compact Inline Raytheon Hybrid Stirling/Pulse Tube 2-Stage (CI-RSP2) cryocoolers are being developed to satisfy this suite of requirements. This lightweight, compact, efficient, low vibration cryocooler combines proven 1-stage (RS1 or RP1) and 2-stage (RSP2) cold-head architectures with an inventive set of warm-end mechanisms into a single cooler module, allowing the moving mechanisms for the compressor and the Stirling displacer to be consolidated onto a common axis and in a common working volume. The CI cryocooler is a significant departure from the current Stirling cryocoolers in which the compressor mechanisms are remote from the Stirling displacer mechanism. Placing all of the mechanisms in a single volume and on a single axis provides benefits in terms of package size (30% reduction), mass (30% reduction), thermodynamic efficiency (>20% improvement) and exported vibration performance (?25 mN peak in all three orthogonal axes at frequencies from 1 to 500 Hz). The main benefit of axial symmetry is that proven balancing techniques and hardware can be utilized to null all motion along the common axis. Low vibration translates to better sensor performance resulting in simpler, more direct mechanical mounting configurations, eliminating the need for convoluted, expensive, massive, long lead damping hardware.

Schaefer, B. R.; Bellis, L.; Ellis, M. J.; Conrad, T. [Raytheon Space and Airborne Systems, 2000 E. El Segundo Blvd., El Segundo, CA 90245 (United States)

2014-01-29T23:59:59.000Z

299

Compact Imaging Spectrometer Utilizing Immersed Gratings  

DOE Patents [OSTI]

A compact imaging spectrometer with an immersive diffraction grating that compensates optical distortions. The imaging spectrometer comprises an entrance slit for transmitting light, a system for receiving the light and directing the light, an immersion grating, and a detector array. The entrance slit, the system for receiving the light, the immersion grating, and the detector array are positioned wherein the entrance slit transmits light to the system for receiving the light and the system for receiving the light directs the light to the immersion grating and the immersion grating receives the light and directs the light through an optical element to the detector array.

Chrisp, Michael P. (Danville, CA); Lerner, Scott A. (Corvallis, OR); Kuzmenko, Paul J. (Livermore, CA); Bennett, Charles L. (Livermore, CA)

2006-03-21T23:59:59.000Z

300

Compact Power Inc CPI | Open Energy Information  

Open Energy Info (EERE)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home5b9fcbce19 NoPublic Utilities Address: 160Benin:EnergyWisconsin: Energy,(EC-LEDS)Columbus ElectricRefuseEnergyCompact Power Inc

Note: This page contains sample records for the topic "incandescent compact fluorescent" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Compact Absorption Chiller - Energy Innovation Portal  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation Proposed New SubstationCleanCommunity Involvement and Making aCompact soft x-ray

302

Sandia National Laboratories: Compact Linear Fesnel Reflector  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmosphericNuclear Security Administration the1 -the Mid-Infrared0Energy AdvancedEnergyEnergyMappingCombustionBiofuels OnWindCompact

303

Final Technical Report - Development of a tunable diode laser induced fluorescence diagnostic for the Princeton magnetic nozzle experiment: West Virginia University and Princeton Plasma Physics Laboratory  

SciTech Connect (OSTI)

This project involves the construction of a compact, portable, laser induced fluorescence (LIF) diagnostic for measurements of neutral helium, neutral argon, and argon ion velocity space distributions in a high density, steady state, helicon source. The project is collaborative effort between the Princeton Plasma Physics Laboratory (PPPL) and the West Virginia University (WVU) helicon source group. A key feature of the diagnostic system will be the use of tunable diode lasers instead of the tunable dye lasers typically used in LIF experiments.

Earl Scime

2006-11-07T23:59:59.000Z

304

ROSAT Observations of Compact Groups of Galaxies  

E-Print Network [OSTI]

A search for X-ray emission from compact groups revealed detection from 8 out of the 12 HCG images extracted from the ROSAT public archive. For two of them the X-ray emission originates from galaxies in the group. On the contrary, three groups show an extended emission clearly caused by hot intracluster gas. A Raymond-Smith hot plasma model provides an excellent fit to the X-ray spectra. The estimated temperatures are distributed in a quite narrow range (from 0.73 to 0.92 keV) and are consistent, within the errors, with 0.9 keV. The luminosity ranging from 0.75 to $5.1\\cdot10^{42}$erg s$^{-1}$. The most relevant result is the low metal abundance surely detected in two of them and likely in a third that characterizes the hot gas cloud responsible for the X-ray emission. The data concerning the remaining 3 detected compact groups are not sufficient to discriminate with certainty between diffuse and/or point-like X-ray emission. However the results of the spectral analysis point to the presence of a hot gas again with low metal abundance.

P. Saracco; P. Ciliegi

1994-12-15T23:59:59.000Z

305

Strange Quark Matter and Compact Stars  

E-Print Network [OSTI]

Astrophysicists distinguish between three different types of compact stars. These are white dwarfs, neutron stars, and black holes. The former contain matter in one of the densest forms found in the Universe which, together with the unprecedented progress in observational astronomy, make such stars superb astrophysical laboratories for a broad range of most striking physical phenomena. These range from nuclear processes on the stellar surface to processes in electron degenerate matter at subnuclear densities to boson condensates and the existence of new states of baryonic matter--like color superconducting quark matter--at supernuclear densities. More than that, according to the strange matter hypothesis strange quark matter could be more stable than nuclear matter, in which case neutron stars should be largely composed of pure quark matter possibly enveloped in thin nuclear crusts. Another remarkable implication of the hypothesis is the possible existence of a new class of white dwarfs. This article aims at giving an overview of all these striking physical possibilities, with an emphasis on the astrophysical phenomenology of strange quark matter. Possible observational signatures associated with the theoretically proposed states of matter inside compact stars are discussed as well. They will provide most valuable information about the phase diagram of superdense nuclear matter at high baryon number density but low temperature, which is not accessible to relativistic heavy ion collision experiments.

Fridolin Weber

2004-09-27T23:59:59.000Z

306

Compact wavefunctions from compressed imaginary time evolution  

E-Print Network [OSTI]

Simulation of quantum systems promises to deliver physical and chemical predictions for the frontiers of technology. Unfortunately, the exact representation of these systems is plagued by the exponential growth of dimension with the number of particles, or colloquially, the curse of dimensionality. The success of approximation methods has hinged on the relative simplicity of physical systems with respect to the exponentially complex worst case. Exploiting this relative simplicity has required detailed knowledge of the physical system under study. In this work, we introduce a general and efficient black box method for many-body quantum systems that utilizes technology from compressed sensing to find the most compact wavefunction possible without detailed knowledge of the system. It is a Multicomponent Adaptive Greedy Iterative Compression (MAGIC) scheme. No knowledge is assumed in the structure of the problem other than correct particle statistics. This method can be applied to many quantum systems such as spins, qubits, oscillators, or electronic systems. As an application, we use this technique to compute ground state electronic wavefunctions of hydrogen fluoride and recover 98% of the basis set correlation energy or equivalently 99.996% of the total energy with $50$ configurations out of a possible $10^7$. Building from this compactness, we introduce the idea of nuclear union configuration interaction for improving the description of reaction coordinates and use it to study the dissociation of hydrogen fluoride and the helium dimer.

Jarrod R. McClean; Aln Aspuru-Guzik

2014-09-25T23:59:59.000Z

307

Symmetry, Compact Closure and Dagger Compactness for Categories of Convex Operational Models  

E-Print Network [OSTI]

In the categorical approach to the foundations of quantum theory, one begins with a symmetric monoidal category, the objects of which represent physical systems, and the morphisms of which represent physical processes. Usually, this category is taken to be at least compact closed, and more often, dagger compact, enforcing a certain self-duality, whereby preparation processes (roughly, states) are inter-convertible with processes of registration (roughly, measurement outcomes). This is in contrast to the more concrete "operational" approach, in which the states and measurement outcomes associated with a physical system are represented in terms of what we here call a "convex operational model": a certain dual pair of ordered linear spaces -- generally, {\\em not} isomorphic to one another. On the other hand, state spaces for which there is such an isomorphism, which we term {\\em weakly self-dual}, play an important role in reconstructions of various quantum-information theoretic protocols, including teleportation and ensemble steering. In this paper, we characterize compact closure of symmetric monoidal categories of convex operational models in two ways: as a statement about the existence of teleportation protocols, and as the principle that every process allowed by that theory can be realized as an instance of a remote evaluation protocol --- hence, as a form of classical probabilistic conditioning. In a large class of cases, which includes both the classical and quantum cases, the relevant compact closed categories are degenerate, in the weak sense that every object is its own dual. We characterize the dagger-compactness of such a category (with respect to the natural adjoint) in terms of the existence, for each system, of a {\\em symmetric} bipartite state, the associated conditioning map of which is an isomorphism.

Howard Barnum; Ross Duncan; Alexander Wilce

2010-04-16T23:59:59.000Z

308

Epi-Fluorescence Inverted Microscope (Zeiss,  

E-Print Network [OSTI]

Epi-Fluorescence Inverted Microscope (Zeiss, Observer Z1) April 2013 #12;Start Up cont. · Turn) #12;Using the Microscope cont. · On an inverted microscope samples on a glass slide are usually viewed

Subramanian, Venkat

309

Probing the denatured state ensemble with fluorescence  

E-Print Network [OSTI]

around the original tryptophan substitutions in RNase Sa. Regardless of the denaturant, ?max for the proteins and model compounds differed very little, 349.3 1.2 nm. However, significant differences were observed in the fluorescence intensity at ?max...

Alston, Roy Willis

2004-09-30T23:59:59.000Z

310

Development, Test and Demonstration of a Cost-Effective, Compact...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Development, Test and Demonstration of a Cost-Effective, Compact, Light-Weight, and Scalable High Temperature Inverter for HEVs, PHEVs, and FCVs Development, Test and Demonstration...

311

Western Interstate Nuclear Compact State Nuclear Policy (Multiple States)  

Broader source: Energy.gov [DOE]

Legislation authorizes states' entrance into the Western Interstate Nuclear Compact, which aims to undertake the cooperation of participating states in deriving the optimum benefit from nuclear and...

312

accreting compact stars: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

of the millisecond brightness oscillations from low mass X-ray binaries during thermonuclear bursts can provide us with important information about compact star parameters....

313

Southwestern Low-Level Radioactive Waste Disposal Compact (South Dakota)  

Broader source: Energy.gov [DOE]

This legislation authorizes the state's entrance into the Southwestern Low-Level Radioactive Waste Disposal Compact, which provides for the cooperative management of low-level radioactive waste....

314

Appalachian States Low-Level Radioactive Waste Compact (Maryland)  

Broader source: Energy.gov [DOE]

This legislation authorizes Maryland's entrance into the Appalachian States Low-Level Radioactive Waste Compact, which seeks to promote interstate cooperation for the proper management and disposal...

315

Compact heat exchangers for condensation applications: Yesterday, today and tomorrow  

SciTech Connect (OSTI)

Compact heat exchangers are being increasingly considered for condensation applications in the process, cryogenic, aerospace, power and refrigeration industries. In this paper, different configurations available for condensation applications are analyzed and the current state-of-the-knowledge for the design of compact condensers is evaluated. The key technical issues for the design and development of compact heat exchangers for condensation applications are analyzed and major advantages are identified. The experimental data and performance prediction methods reported in the literature are analyzed to evaluate the present design capabilities for different compact heat-exchanger configurations. The design flexibility is evaluated for the development of new condensation applications, including integration with other process equipment.

Panchal, C.B.

1993-07-01T23:59:59.000Z

316

Cape Light Compact- Residential Energy Efficiency Rebate Program  

Broader source: Energy.gov [DOE]

Cape Light Compact (CLC) offers a variety of financial incentives to customers for purchasing energy efficient residential equipment. Residential customers can take advantage of incentives on...

317

Interstate Oil and Gas Conservation Compact (Multiple States)  

Broader source: Energy.gov [DOE]

The Interstate Oil and Gas Compact Commission assists member states efficiently maximize oil and natural gas resources through sound regulatory practices while protecting the nation's health,...

318

Multiplexed fluorescence detector system for capillary electrophoresis  

DOE Patents [OSTI]

A fluorescence detection system for capillary electrophoresis is provided wherein the detection system can simultaneously excite fluorescence and substantially simultaneously monitor separations in multiple capillaries. This multiplexing approach involves laser irradiation of a sample in a plurality of capillaries through optical fibers that are coupled individually with the capillaries. The array is imaged orthogonally through a microscope onto a charge-coupled device camera for signal analysis. 14 figures.

Yeung, E.S.; Taylor, J.A.

1994-06-28T23:59:59.000Z

319

Multiplexed fluorescence detector system for capillary electrophoresis  

DOE Patents [OSTI]

A fluorescence detection system for capillary electrophoresis is provided wherein the detection system can simultaneously excite fluorescence and substantially simultaneously monitor separations in multiple capillaries. This multiplexing approach involves laser irradiation of a sample in a plurality of capillaries through optical fibers that are coupled individually with the capillaries. The array is imaged orthogonally through a microscope onto a charge-coupled device camera for signal analysis. 14 figs.

Yeung, E.S.; Taylor, J.A.

1996-03-12T23:59:59.000Z

320

Research Focus High-throughput screens for fluorescent dye discovery  

E-Print Network [OSTI]

Research Focus High-throughput screens for fluorescent dye discovery Vebjorn Ljosa and Anne E of a combinatorial library of fluorescent compounds discovered fluorescent dyes that were able to distinguish myoblasts from differentiated myotubes. New fluorescent dyes that respond to biologically relevant changes

Carpenter, Anne E.

Note: This page contains sample records for the topic "incandescent compact fluorescent" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Ultratrace analysis of transuranic actinides by laser-induced fluorescence  

DOE Patents [OSTI]

Ultratrace quantities of transuranic actinides are detected indirectly by their effect on the fluorescent emissions of a preselected fluorescent species. Transuranic actinides in a sample are coprecipitated with a host lattice material containing at least one preselected fluorescent species. The actinide either quenches or enhances the laser-induced fluorescence of the preselected fluorescent species. The degree of enhancement or quenching is quantitatively related to the concentration of actinide in the sample.

Miller, S.M.

1983-10-31T23:59:59.000Z

322

Collective Deceleration: Toward a Compact Beam Dump  

SciTech Connect (OSTI)

With the increasing development of laser accelerators, the electron energy is already beyond GeV and even higher in near future. Conventional beam dump based on ionization or radiation loss mechanism is cumbersome and costly, also has radiological hazards. We revisit the stopping power of high-energy charged particles in matter and discuss the associated problem of beam dump from the point of view of collective deceleration. The collective stopping length in an ionized gas can be several orders of magnitude shorter than the Bethe-Bloch and multiple electromagnetic cascades stopping length in solid. At the mean time, the tenuous density of the gas makes the radioactivation negligible. Such a compact and non-radioactivating beam dump works well for short and dense bunches, which is typically generated from laser wakefield accelerator.

Wu, H.-C.; /Munich, Max Planck Inst. Quantenopt.; Tajima, T.; Habs, D.; /Munich, Max Planck Inst. Quantenopt. /Munich U.; Chao, A.W.; /SLAC; Meyer-ter-Vehn, J.; /Munich, Max Planck Inst. Quantenopt.

2011-11-28T23:59:59.000Z

323

Compact high voltage solid state switch  

DOE Patents [OSTI]

A compact, solid state, high voltage switch capable of high conduction current with a high rate of current risetime (high di/dt) that can be used to replace thyratrons in existing and new applications. The switch has multiple thyristors packaged in a single enclosure. Each thyristor has its own gate drive circuit that circuit obtains its energy from the energy that is being switched in the main circuit. The gate drives are triggered with a low voltage, low current pulse isolated by a small inexpensive transformer. The gate circuits can also be triggered with an optical signal, eliminating the trigger transformer altogether. This approach makes it easier to connect many thyristors in series to obtain the hold off voltages of greater than 80 kV.

Glidden, Steven C.

2003-09-23T23:59:59.000Z

324

Compact hydrogen/helium isotope mass spectrometer  

DOE Patents [OSTI]

The compact hydrogen and helium isotope mass spectrometer of the present invention combines low mass-resolution ion mass spectrometry and beam-foil interaction technology to unambiguously detect and quantify deuterium (D), tritium (T), hydrogen molecule (H.sub.2, HD, D.sub.2, HT, DT, and T.sub.2), .sup.3 He, and .sup.4 He concentrations and concentration variations. The spectrometer provides real-time, high sensitivity, and high accuracy measurements. Currently, no fieldable D or molecular speciation detectors exist. Furthermore, the present spectrometer has a significant advantage over traditional T detectors: no confusion of the measurements by other beta-emitters, and complete separation of atomic and molecular species of equivalent atomic mass (e.g., HD and .sup.3 He).

Funsten, Herbert O. (Los Alamos, NM); McComas, David J. (Los Alamos, NM); Scime, Earl E. (Morgantown, WV)

1996-01-01T23:59:59.000Z

325

Compact and highly efficient laser pump cavity  

DOE Patents [OSTI]

A new, compact, side-pumped laser pump cavity design which uses non-conventional optics for injection of laser-diode light into a laser pump chamber includes a plurality of elongated light concentration channels. In one embodiment, the light concentration channels are compound parabolic concentrators (CPC) which have very small exit apertures so that light will not escape from the pumping chamber and will be multiply reflected through the laser rod. This new design effectively traps the pump radiation inside the pump chamber that encloses the laser rod. It enables more uniform laser pumping and highly effective recycle of pump radiation, leading to significantly improved laser performance. This new design also effectively widens the acceptable radiation wavelength of the diodes, resulting in a more reliable laser performance with lower cost.

Chang, Jim J. (Dublin, CA); Bass, Isaac L. (Castro Valley, CA); Zapata, Luis E. (Livermore, CA)

1999-01-01T23:59:59.000Z

326

Compact imaging spectrometer utilizing immersed gratings  

DOE Patents [OSTI]

A compact imaging spectrometer with an immersive diffraction grating that compensates optical distortions. The imaging spectrometer comprises an entrance slit for transmitting light, means for receiving the light and directing the light, an immersion grating, and a detector array. The entrance slit, the means for receiving the light, the immersion grating, and the detector array are positioned wherein the entrance slit transmits light to the means for receiving the light and the means for receiving the light directs the light to the immersion grating and the immersion grating receives the light and directs the light to the means for receiving the light, and the means for receiving the light directs the light to the detector array.

Chrisp, Michael P. (Danville, CA); Lerner, Scott A. (Corvallis, OR); Kuzmenko, Paul J. (Livermore, CA); Bennett, Charles L. (Livermore, CA)

2007-07-03T23:59:59.000Z

327

Compact microwave ion source for industrial applications  

SciTech Connect (OSTI)

A 2.45 GHz microwave ion source for ion implanters has many good properties for industrial application, such as easy maintenance and long lifetime, and it should be compact for budget and space. But, it has a dc current supply for the solenoid and a rf generator for plasma generation. Usually, they are located on high voltage platform because they are electrically connected with beam extraction power supply. Using permanent magnet solenoid and multi-layer dc break, high voltage deck and high voltage isolation transformer can be eliminated, and the dose rate on targets can be controlled by pulse duty control with semiconductor high voltage switch. Because the beam optics does not change, beam transfer components, such as focusing elements and beam shutter, can be eliminated. It has shown the good performances in budget and space for industrial applications of ion beams.

Cho, Yong-Sub; Kim, Dae-Il; Kim, Han-Sung; Seol, Kyung-Tae; Kwon, Hyeok-Jung; Hong, In-Seok [Proton Engineering Frontier Project, Korea Atomic Energy Research Institute, Daejeon 305-353 (Korea, Republic of)

2012-02-15T23:59:59.000Z

328

Stirling Air Conditioner for Compact Cooling  

SciTech Connect (OSTI)

BEETIT Project: Infinia is developing a compact air conditioner that uses an unconventional high efficient Stirling cycle system (vs. conventional vapor compression systems) to produce cool air that is energy efficient and does not rely on polluting refrigerants. The Stirling cycle system is a type of air conditioning system that uses a motor with a piston to remove heat to the outside atmosphere using a gas refrigerant. To date, Stirling systems have been expensive and have not had the right kind of heat exchanger to help cool air efficiently. Infinia is using chip cooling technology from the computer industry to make improvements to the heat exchanger and improve system performance. Infinias air conditioner uses helium gas as refrigerant, an environmentally benign gas that does not react with other chemicals and does not burn. Infinias improvements to the Stirling cycle system will enable the cost-effective mass production of high-efficiency air conditioners that use no polluting refrigerants.

None

2010-09-01T23:59:59.000Z

329

Cooldown of the Compact Ignition Tokamak  

SciTech Connect (OSTI)

Cooldown of the Compact Ignition Tokamak (CIT) with the baseline liquid nitrogen cooling system was analyzed. On the basis of this analysis and present knowledge of the two-phase heat transfer, the current baseline CIT can be cooled down in about 1.5 h. An extensive heat transfer test program is recommended to reduce uncertainty in the heat transfer performance and to explore methods for minimizing the cooldown time. An alternate CIT cooldown system is described which uses a pressurized gaseous helium coolant in a closed-loop system. It is shown analytically that this system will cool down the CIT well within 1 h. Confidence in this analysis is sufficiently high that a heat transfer test program would not be necessary. The added cost of this alternate system is estimated to be about $5.3 million. This helium cooling system represents a reasonable backup approach to liquid nitrogen cooling of the CIT. 3 refs., 12 figs., 3 tabs.

Keeton, D.C.

1987-08-01T23:59:59.000Z

330

Compact conscious animal positron emission tomography scanner  

DOE Patents [OSTI]

A method of serially transferring annihilation information in a compact positron emission tomography (PET) scanner includes generating a time signal for an event, generating an address signal representing a detecting channel, generating a detector channel signal including the time and address signals, and generating a composite signal including the channel signal and similarly generated signals. The composite signal includes events from detectors in a block and is serially output. An apparatus that serially transfers annihilation information from a block includes time signal generators for detectors in a block and an address and channel signal generator. The PET scanner includes a ring tomograph that mounts onto a portion of an animal, which includes opposing block pairs. Each of the blocks in a block pair includes a scintillator layer, detection array, front-end array, and a serial encoder. The serial encoder includes time signal generators and an address signal and channel signal generator.

Schyler, David J. (Bellport, NY); O'Connor, Paul (Bellport, NY); Woody, Craig (Setauket, NY); Junnarkar, Sachin Shrirang (Sound Beach, NY); Radeka, Veljko (Bellport, NY); Vaska, Paul (Sound Beach, NY); Pratte, Jean-Francois (Stony Brook, NY); Volkow, Nora (Chevy Chase, MD)

2006-10-24T23:59:59.000Z

331

Symmetry, Compact Closure and Dagger Compactness for Categories of Convex Operational Models  

E-Print Network [OSTI]

In the categorical approach to the foundations of quantum theory, one begins with a symmetric monoidal category, the objects of which represent physical systems, and the morphisms of which represent physical processes. Usually, this category is taken to be at least compact closed, and more often, dagger compact, enforcing a certain self-duality, whereby preparation processes (roughly, states) are inter-convertible with processes of registration (roughly, measurement outcomes). This is in contrast to the more concrete "operational" approach, in which the states and measurement outcomes associated with a physical system are represented in terms of what we here call a "convex operational model": a certain dual pair of ordered linear spaces -- generally, {\\em not} isomorphic to one another. On the other hand, state spaces for which there is such an isomorphism, which we term {\\em weakly self-dual}, play an important role in reconstructions of various quantum-information theoretic protocols, including teleportatio...

Barnum, Howard; Wilce, Alexander

2010-01-01T23:59:59.000Z

332

Synonymous Address Compaction for Energy Reduction in Data TLB  

E-Print Network [OSTI]

Synonymous Address Compaction for Energy Reduction in Data TLB Chinnakrishnan S. Ballapuram chinnak and Computer Engineering College of Computing Georgia Institute of Technology, Atlanta, GA 30332 ABSTRACT-cycle compaction of address translation requests in order to save energy in the data TLB. Our results show

Lee, Hsien-Hsin "Sean"

333

GRI-04/0067 Evaluation of Soil Compaction  

E-Print Network [OSTI]

GRI-04/0067 Evaluation of Soil Compaction Measuring Devices FINAL REPORT Prepared by Distribution Title Soil Compaction Measuring Device Study Contractor GAS TECHNOLOGY INSTITUTE 1700 S. Mt. Prospect, KeySpan Energy, PECO Energy Company, Public Service Electric & Gas, Washington Gas, Environmental

334

Modelling the mechanical behaviour of pharmaceutical powders during compaction  

E-Print Network [OSTI]

are made of dry powder through a powder compaction process. In the pharmaceutical industry, billionsModelling the mechanical behaviour of pharmaceutical powders during compaction C.-Y. Wua,T, O.M. Ruddyb , A.C. Benthamb , B.C. Hancockc , S.M. Besta , J.A. Elliotta a Pfizer Institute for Pharmaceutical

Elliott, James

335

THE ARIES-CS COMPACT STELLARATOR FUSION POWER PLANT  

E-Print Network [OSTI]

THE ARIES-CS COMPACT STELLARATOR FUSION POWER PLANT F. NAJMABADI* and A. R. RAFFRAY Center stellarator power plants, ARIES-CS, has been conducted to explore attrac- tive compact stellarator by earlier stellarator power plant studies had led to cost projections much higher than those of the advanced

Raffray, A. Ren

336

Modeling compaction-induced energy dissipation of granular HMX  

SciTech Connect (OSTI)

A thermodynamically consistent model is developed for the compaction of granular solids. The model is an extension of the single phase limit of two-phase continuum models used to describe Deflagration-to-Detonation Transition (DDT) experiments. The focus is on the energetics and dissipation of the compaction process. Changes in volume fraction are partitioned into reversible and irreversible components. Unlike conventional DDT models, the model is applicable from the quasi-static to dynamic compaction regimes for elastic, plastic, or brittle materials. When applied to the compaction of granular HMX (a brittle material), the model predicts results commensurate with experiments including stress relaxation, hysteresis, and energy dissipation. The model provides a suitable starting point for the development of thermal energy localization sub-scale models based on compaction-induced dissipation.

Gonthier, K.A. [Lamar Univ., Beaumont, TX (US). Dept. of Mechanical Engineering; Menikoff, R.; Son, S.F.; Asay, B.W. [Los Alamos National Lab., NM (US)

1998-12-31T23:59:59.000Z

337

The Size of Compact Extra Dimensions from Blackbody Radiation Laws  

E-Print Network [OSTI]

In this work we generalize the Stefan-Boltzmann and Wien's displacement laws for a $D$-dimensional manifold composed by 4 non-compact dimensions and $D-4$ compact dimensions, $ R^{1,3}$ x $T^{D-4} $. The electromagnetic field is assumed to pervade all compact and non-compact dimensions. In particular, the total radiated power becomes $ R(T) = \\sigma_B T^4 + \\sigma_D (a) \\, T^D $, where $a$ is the size of the compact extra dimensions. For $D=10$, predicted from String Theory, and $D=11$, from M-Theory, the outcomes agree with available experimental data for $a$ as high as 2 x $10^{-7}$m.

Ramaton Ramos; Henrique Boschi-Filho

2014-04-28T23:59:59.000Z

338

Supercontinuum Stimulated Emission Depletion Fluorescence Lifetime Imaging  

SciTech Connect (OSTI)

Supercontinuum (SC) stimulated emission depletion (STED) fluorescence lifetime imaging is demonstrated by using time-correlated single-photon counting (TCSPC) detection. The spatial resolution of the developed STED instrument was measured by imaging monodispersed 40-nm fluorescent beads and then determining their fwhm, and was 36 9 and 40 10 nm in the X and Y coordinates, respectively. The same beads measured by confocal microscopy were 450 50 and 430 30 nm, which is larger than the diffraction limit of light due to underfilling the microscope objective. Underfilling the objective and time gating the signal were necessary to achieve the stated STED spatial resolution. The same fluorescence lifetime (2.0 0.1 ns) was measured for the fluorescent beads by using confocal or STED lifetime imaging. The instrument has been applied to study Alexa Fluor 594-phalloidin labeled F-actin-rich projections with dimensions smaller than the diffraction limit of light in cultured cells. Fluorescence lifetimes of the actin-rich projections range from 2.2 to 2.9 ns as measured by STED lifetime imaging.

Lesoine, Michael; Bose, Sayantan; Petrich, Jacob; Smith, Emily

2012-06-13T23:59:59.000Z

339

New Reflector CFLs that Can Take the Heat  

SciTech Connect (OSTI)

Reflector compact fluorescent bulbs (R-CFLs) are a wise choice for the energy savvy because they offer energy savings of up to 66 percent compared to incandescent reflectors. But some R-CFLs have suffered performance problems (including premature failure) when used in high-temperature environments, such as recessed downlight fixtures located in insulated ceilings with airtight housings. To help address this issue, the U.S. Dept. of Energy (DOE) is working with lamp manufacturers to improve the quality and performance of screw-based reflector CFLs in high-heat applications.

Vogt, Susan

2005-03-01T23:59:59.000Z

340

Structural Reliability: Assessing the Condition and Reliability of Casing in Compacting Reservoirs  

E-Print Network [OSTI]

. Effective stress may exceed rock compressive strength, inducing compaction. Wells in compacting reservoirs risk high failure and deformation rates. This project introduces the concept of structural reliability to quantify casing failure risks in compacting...

Chantose, Prasongsit

2012-02-14T23:59:59.000Z

Note: This page contains sample records for the topic "incandescent compact fluorescent" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Thermal and electrical conduction in the compaction direction of exfoliated graphite  

E-Print Network [OSTI]

Thermal and electrical conduction in the compaction direction of exfoliated graphite in the compaction direction of graphite-flake-based exfoliated graphite have been decoupled. The compact Exfoliated graphite is elongated graphite particles obtained by the exfoliation (typically involving rapid

Chung, Deborah D.L.

342

Fluorescence energy transfer enhancement in aluminum nanoapertures  

E-Print Network [OSTI]

Zero-mode waveguides (ZMWs) are confining light into attoliter volumes, enabling single molecule fluorescence experiments at physiological micromolar concentrations. Among the fluorescence spectroscopy techniques that can be enhanced by ZMWs, F\\"{o}rster resonance energy transfer (FRET) is one of the most widely used in life sciences. Combining zero-mode waveguides with FRET provides new opportunities to investigate biochemical structures or follow interaction dynamics at micromolar concentration with single molecule resolution. However, prior to any quantitative FRET analysis on biological samples, it is crucial to establish first the influence of the ZMW on the FRET process. Here, we quantify the FRET rates and efficiencies between individual donor-acceptor fluorophore pairs diffusing in aluminum zero-mode waveguides. Aluminum ZMWs are important structures thanks to their commercial availability and the large literature describing their use for single molecule fluorescence spectroscopy. We also compare the ...

de Torres, Juan; Moparthi, Satish Babu; Grigoriev, Victor; Wenger, Jrome

2015-01-01T23:59:59.000Z

343

System Architecture Directions for a Software-Defined Lighting Infrastructure  

E-Print Network [OSTI]

spectrum of an outdoor environment and a typical fluorescent tube-lit office space. Indoor spectrum to incandescent and fluorescent lights. Unfortunately, the remarkable march of semiconductor technology a renaissance. The staple of illumi- nation for one and a half centuries, the incandescent bulb, is being phased

Dutta, Prabal

344

Fluorescent labels and their use in separations  

DOE Patents [OSTI]

Compositions are provided comprising sets of fluorescent labels carrying pairs of donor and acceptor dye molecules, designed for efficient excitation of the donors at a single wavelength and emission from the acceptor in each of the pairs at different wavelengths. The different molecules having different donor-acceptor pairs can be modified to have substantially the same mobility under separation conditions, by varying the distance between the donor and acceptor in a given pair. Particularly, the fluorescent compositions find use as labels in sequencing nucleic acids.

Mathies, Richard A. (El Cerrito, CA); Glazer, Alexander (Orinda, CA); Ju, Jingyue (Berkeley, CA)

1997-01-01T23:59:59.000Z

345

Ultrabright fluorescent OLEDS using triplet sinks  

DOE Patents [OSTI]

A first device is provided. The first device further comprises an organic light emitting device. The organic light emitting device further comprises an anode, a cathode, and an emissive layer disposed between the anode and the cathode. The emissive layer further comprises an organic host compound, an organic emitting compound capable of fluorescent emission at room temperature, and an organic dopant compound. The triplet energy of the dopant compound is lower than the triplet energy of the host compound. The dopant compound does not strongly absorb the fluorescent emission of the emitting compound.

Zhang, Yifan; Forrest, Stephen R; Thompson, Mark

2013-06-04T23:59:59.000Z

346

Process for forming coal compacts and product thereof  

DOE Patents [OSTI]

A process for forming durable, mechanically strong compacts from coal particulates without use of a binder is disclosed. The process involves applying a compressive stress to a particulate feed comprising substantially water-saturated coal particles while the feed is heated to a final compaction temperature in excess of about 100.degree. C. The water present in the feed remains substantially in the liquid phase throughout the compact forming process. This is achieved by heating and compressing the particulate feed and cooling the formed compact at a pressure sufficient to prevent water present in the feed from boiling. The compacts produced by the process have a moisture content near their water saturation point. As a result, these compacts absorb little water and retain exceptional mechanical strength when immersed in high pressure water. The process can be used to form large, cylindrically-shaped compacts from coal particles (i.e., "coal logs") so that the coal can be transported in a hydraulic coal log pipeline.

Gunnink, Brett (Columbia, MO); Kanunar, Jayanth (Arlington, MA); Liang, Zhuoxiong (San Francisco, CA)

2002-01-01T23:59:59.000Z

347

COMPACTION OF FIBERBOARD IN A 9975 SHIPPING PACKAGE  

SciTech Connect (OSTI)

Compaction of lower layers in the fiberboard overpack has been observed in 9975 packages that contain elevated moisture. Lab testing has resulted in a better understanding of (1) the relationship between the fiberboard moisture level and compaction of the lower fiberboard assembly, and (2) the behavior of the fiberboard during transport. In laboratory tests, higher moisture content has been shown to correspond to higher total compaction of fiberboard material, greater rate of compaction, and continued compaction over a longer period of time. In addition, laboratory tests have shown that the application of a dynamic load results in higher fiberboard compaction. The test conditions and sample geometric/loading configurations were chosen to simulate the regulatory requirements for 9975 package input dynamic loading. Dynamic testing was conducted over a period of several months to acquire immediate and cumulative changes in geometric data for various moisture levels. Currently, one sample set has undergone a complete dynamic test regimen, while testing of another set is still in-progress. The dynamic input, data acquisition, test effects on sample dynamic parameters, and interim results from this test program will be summarized and compared to regulatory specifications for dynamic loading. This will provide a basis from which to evaluate the impact of moisture and fiberboard compaction on the safety basis for transportation (Safety Analysis Report for Packaging) and storage (facility Documented Safety Analysis) at the Savannah River Site (SRS).

Stefek, T.; Daugherty, W.; Estochen, E.; Leduc, D.

2011-05-11T23:59:59.000Z

348

Compact noninvasive electron bunch-length monitor  

DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

A compact rf cavity was constructed that simultaneously resonates at many harmonic modes when excited by a repetitive bunched electron beam passing through its bore. The excitation of these modes provides a Fourier description of the temporal characteristics of the bunch train. The cavity was used to noninvasively characterize electron bunches produced from thin and thick GaAs photocathodes inside a DC high voltage photogun illuminated with 37 ps (full width half maximum, FWHM) laser pulses at repetition rates near 1500 MHz, at average beam current from 5 to 500????A , and at beam energy from 75 to 195 keV. The cavity bunch-length monitor could detect electron bunches as short as 57 ps (FWHM) when connected directly to a sampling oscilloscope, and could clearly distinguish bunches with varying degrees of space-charge induced growth and with different tail signatures. Efforts are under way to detect shorter bunches by designing cavities with increased bandwidth. This demonstration lends credibility to the idea that these cavities could also be used for other applications, including bunching and shaping, when driven with external rf.

Roberts, B.; Mammei, R. R.; Poelker, M.; McCarter, J. L.

2012-12-01T23:59:59.000Z

349

GUTs on Compact Type IIB Orientifolds  

SciTech Connect (OSTI)

We systematically analyze globally consistent SU(5) GUT models on intersecting D7-branes in genuine Calabi-Yau orientifolds with O3- and O7-planes. Beyond the well-known tadpole and K-theory cancellation conditions there exist a number of additional subtle but quite restrictive constraints. For the realization of SU(5) GUTs with gauge symmetry breaking via U(1)Y flux we present two classes of suitable Calabi-Yau manifolds defined via del Pezzo transitions of the elliptically fibred hypersurface P{sub 1,1,1,6,9}[18] and of the Quintic P{sub 1,1,1,1,1}[5], respectively. To define an orientifold projection we classify all involutions on del Pezzo surfaces. We work out the model building prospects of these geometries and present five globally consistent string GUT models in detail, including a 3-generation SU(5) model with no exotics whatsoever. We also realize other phenomenological features such as the 10 10 5{sub H} Yukawa coupling and comment on the possibility of moduli stabilization, where we find an entire new set of so-called swiss-cheese type Calabi-Yau manifolds. It is expected that both the general constrained structure and the concrete models lift to F-theory vacua on compact Calabi-Yau fourfolds.

Blumenhagen, Ralph; /Munich, Max Planck Inst.; Braun, Volker; /Dublin Inst.; Grimm, Thomas W.; /Bonn U.; Weigand, Timo; /SLAC

2008-12-01T23:59:59.000Z

350

The spheromak as a compact fusion reactor  

SciTech Connect (OSTI)

After summarizing the economic and utility-based rationale for compact, higher-power-density fusion reactors, the gun-sustained spheromak concept is explored as one of a number of poloidal-field-dominated confinement configurations that might improve the prospects for economically attractive and operationally simplified fusion power plants. Using a comprehensive physics/engineering/costing model for the spheromak, guided by realistic engineering constraints and physics extrapolation, a range of cost-optimized reactor design points is presented, and the sensitivity of cost to key physics, engineering, and operational variables is reported. The results presented herein provide the basis for conceptual engineering designs of key fusion-power-core (FPC) subsystems and more detailed plasma modeling of this promising, high mass-power-density concept, which stresses single-piece FPC maintenance, steady-state current drive through electrostatic magnetic helicity injection, a simplified co-axial electrode-divertor, and efficient resistive-coal equilibrium-field coils. The optimal FPC size and the cost estimates project a system that competes aggressively with the best offered by alternative energy sources while simplifying considerably the complexity that has generally been associated with most approaches to magnetic fusion energy.

Hagenson, R.L.; Krakowski, R.A.

1987-03-01T23:59:59.000Z

351

Color superconducting quark matter in compact stars  

E-Print Network [OSTI]

Recent indications for high neutron star masses (M \\sim 2 M_sun) and large radii (R > 12 km) could rule out soft equations of state and have provoked a debate whether the occurence of quark matter in compact stars can be excluded as well. We show that modern quantum field theoretical approaches to quark matter including color superconductivity and a vector meanfield allow a microscopic description of hybrid stars which fulfill the new, strong constraints. For these objects color superconductivity turns out to be an essential ingredient for a successful description of the cooling phenomenology in accordance with recently developed tests. We discuss the energy release in the neutrino untrapping transition as a new aspect of the problem that hybrid stars masquerade themselves as neutron stars. Quark matter searches in future generations of low-temperature/high-density nucleus-nucleus collision experiments such as low-energy RHIC and CBM @ FAIR might face the same problem of an almost crossover behavior of the deconfinement transition. Therefore, diagnostic tools shall be derived from effects of color superconductivity.

D. B. Blaschke; T. Klahn; F. Sandin

2007-12-02T23:59:59.000Z

352

MACHO (MAssive Compact Halo Objects) Data  

DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

The primary aim of the MACHO Project is to test the hypothesis that a significant fraction of the dark matter in the halo of the Milky Way is made up of objects like brown dwarfs or planets: these objects have come to be known as MACHOs, for MAssive Compact Halo Objects. The signature of these objects is the occasional amplification of the light from extragalactic stars by the gravitational lens effect. The amplification can be large, but events are extremely rare: it is necessary to monitor photometrically several million stars for a period of years in order to obtain a useful detection rate. For this purpose MACHO has a two channel system that employs eight CCDs, mounted on the 50 inch telescope at Mt. Stromlo. The high data rate (several GBytes per night) is accommodated by custom electronics and on-line data reduction. The Project has taken more than 27,000 images with this system since June 1992. Analysis of a subset of these data has yielded databases containing light curves in two colors for 8 million stars in the LMC and 10 million in the bulge of the Milky Way. A search for microlensing has turned up four candidates toward the Large Magellanic Cloud and 45 toward the Galactic Bulge. The web page for data provides links to MACHO Project data portals and various specialized interfaces for viewing or searching the data. (Specialized Interface)

353

IONIZED OUTFLOWS FROM COMPACT STEEP SPECTRUM SOURCES  

SciTech Connect (OSTI)

Massive outflows are known to exist, in the form of extended emission-line regions (EELRs), around about one-third of powerful FR II radio sources. We investigate the origin of these EELRs by studying the emission-line regions around compact-steep-spectrum (CSS) radio galaxies that are younger (10{sup 3}-10{sup 5} yr old) versions of the FR II radio galaxies. We have searched for and analyzed the emission-line regions around 11 CSS sources by taking integral field spectra using Gemini Multi-Object Spectrograph on Gemini North. We fit the [O III] {lambda}5007 line and present the velocity maps for each detected emission-line region. We find, in most cases, that the emission-line regions have multi-component velocity structures with different velocity dispersions and/or flux distributions for each component. The velocity gradients of the emission-line gas are mostly well aligned with the radio axis, suggesting a direct causal link between the outflowing gas and the radio jets. The complex velocity structure may be a result of different driving mechanisms related to the onset of the radio jets. We also present the results from the line-ratio diagnostics we used to analyze the ionization mechanism of the extended gas, which supports the scenario where the emission-line regions are ionized by a combination of active galactic nucleus radiation and shock excitation.

Shih, Hsin-Yi; Stockton, Alan; Kewley, Lisa, E-mail: hsshih@ifa.hawaii.edu, E-mail: stockton@ifa.hawaii.edu, E-mail: lisa.kewley@anu.edu.au [Institute for Astronomy, University of Hawaii, 2680 Woodlawn Drive, Honolulu, HI 96822 (United States)

2013-08-01T23:59:59.000Z

354

E-Print Network 3.0 - alamos spheromak compact Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

conditions. The simplicity and compact size of spheromaks provide excellent access for diagnostics... , injection of accelerated spheromak compact tori ... Source: Lawrence...

355

Iron-carbon compacts and process for making them  

DOE Patents [OSTI]

The present invention includes iron-carbon compacts and a process for making them. The process includes preparing a slurry comprising iron powder, furfuryl alcohol, and a polymerization catalyst for initiating the polymerization of the furfuryl alcohol into a resin, and heating the slurry to convert the alcohol into the resin. The resulting mixture is pressed into a green body and heated to form the iron-carbon compact. The compact can be used as, or machined into, a magnetic flux concentrator for an induction heating apparatus.

Sheinberg, Haskell (Santa Fe, NM)

2000-01-01T23:59:59.000Z

356

Compaction of wood chips - physical and pulping characteristics  

SciTech Connect (OSTI)

The temperatures of the uncompacted chips of Pinus taeda were, in general, higher than those of compacted chips when stored outdoors in containers for 236 days. The results of the study after storage indicated that the moisture content (MC) of compacted chips is the same as that of green chips, the uncompacted equivalent mass of chips exhibits a substantial loss in MC, and there is approximately 18% increase in MC of the uncompacted chips simulating a stockpile when compared with MC of green chips. The compaction process neither damaged wood fibers nor altered the chip response to conventional pulping.

Hassan, A.E.; Reeves, R.H.

1980-01-01T23:59:59.000Z

357

Compact Stars in low-mass X-ray binaries  

E-Print Network [OSTI]

We propose a model for compact stars in low-mass X-ray binaries(LMXBs) namely KS 1731-260, EXO 1745-248 and 4U 1608-52. Here we investigate the physical phenomena of a compact star in the LMXBs. Using our model, we have calculated central density, surface density, mass(M) and red-shift for the above mentioned compact stars, which is very much consistent with the reported data. We also obtain the possible equation of state(EOS) of the stars which is physically acceptable.

Sk. Monowar Hossein; Sajahan Molla; Md. Abdul Kayum Jafry; Mehedi Kalam

2014-08-13T23:59:59.000Z

358

CODED SPECTROSCOPY FOR ETHANOL DETECTION IN DIFFUSE, FLUORESCENT MEDIA  

E-Print Network [OSTI]

ABSTRACT CODED SPECTROSCOPY FOR ETHANOL DETECTION IN DIFFUSE, FLUORESCENT MEDIA by Scott Thomas Mc FOR ETHANOL DETECTION IN DIFFUSE, FLUORESCENT MEDIA by Scott Thomas McCain Department of Electrical

359

Codings of separable compact subsets of the first Baire class  

E-Print Network [OSTI]

Let $X$ be a Polish space and $K$ a separable compact subset of the first Baire class on $X$. For every sequence $\\bs$ dense in $\\kk$, the descriptive set-theoretic properties of the set \\[ \\lbf=\\{L\\in[\

Dodos, Pandelis

2008-01-01T23:59:59.000Z

360

A thermodynamic approach for compaction of asphaltic composites  

E-Print Network [OSTI]

results. Modeling asphalt concrete compaction, and also the ability to thereby predict response of mixes, is of great importance to the pavement industry. Asphalt concrete exhibits nonlinear response even at small strains and the response of asphalt...

Koneru, Saradhi

2009-05-15T23:59:59.000Z

Note: This page contains sample records for the topic "incandescent compact fluorescent" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Folded Compact Range Development and Coherent Change Detection Measurement Project  

SciTech Connect (OSTI)

A novel, folded compact range configuration has been developed at the Sandia National Laboratories compact range antenna and radar cross section measurement facility, operated by the Radar/Antenna Department 2343, as a means of performing indoor, environmentally-controlled, far-field simulations of synthetic aperture radar (SAR) coherent change detection (CCD) measurements. This report describes the development of the folded compact range configuration, as well as the initial set of coherent change detection measurements made with the system. These measurements have been highly successful, and have demonstrated the viability of the folded compact range concept in simulating SAR CCD measurements. It is felt that follow-on measurements have the potential of contributing significantly to the body of knowledge available to the scientific community involved in CCD image generation and processing, and that this tool will be a significant aid in the research and development of change detection methodologies.

Sorensen, K.W.

1995-03-01T23:59:59.000Z

362

COMPACTNESS OF COMPOSITION OPERATORS ON BMOA Wayne Smith  

E-Print Network [OSTI]

COMPACTNESS OF COMPOSITION OPERATORS ON BMOA Wayne Smith Abstract. A function theoretic;2 WAYNE SMITH for all functions in the unit ball of BMOA; see Theorem 3.1 in [BCM]. M. Tjani [Tj, Theorem

Smith, Wayne

363

Compact Data Structures with Fast Queries Daniel K. Blandford  

E-Print Network [OSTI]

.5 Decoding Multiple Gamma Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.6 Rank of Computer Science Carnegie Mellon University Pittsburgh, PA 15213 Thesis Committee: Guy E. Blelloch, chair fast queries (and updates) to the data. This thesis describes compact representations of several types

364

Text-Alternative Version: LED Replacements for Linear Fluorescent Lamps  

Broader source: Energy.gov [DOE]

Below is the text-alternative version of the "LED Replacements for Linear Fluorescent Lamps" webcast, held June 20, 2011.

365

Phase Transition in Compact QED(3) and the Josephson Junction  

E-Print Network [OSTI]

We study the finite temperature phase transition in 2+1 dimensional compact QED and its dual theory: Josephson junction. Duality of these theories at zero temperature was established long time ago by Hosotani. Phase transition in compact QED is well studied and we employ the `duality' to study the superconductivity phase transition in a Josephson junction. For a thick junction we obtain a critical temperature in terms of the geometrical properties of the junction.

Vakif K. Onemli; Murat Tas; Bayram Tekin

2001-08-22T23:59:59.000Z

366

Red fluorescent proteins: chromophore formation and cellular applications  

E-Print Network [OSTI]

Red fluorescent proteins: chromophore formation and cellular applications Atsushi Miyawaki1,2 , Daria M Shcherbakova3,4 and Vladislav V Verkhusha3,4 In the last decade, a number of red fluorescent proteins (RFPs) that emit orange, red, and far-red fluorescence have been isolated from anthozoans (corals

Verkhusha, Vladislav V.

367

LIGHT-INDUCED CHANGES IN THE FLUORESCENCE YIELD OF  

E-Print Network [OSTI]

OF PREILLUMINATION ON THE FLUORESCENCE TRANSIENT OF Chlorella pyrenoidosa JOHN C. MUNDAY, JR., and GOVINDJEE From Mexico 88330. ABSTRACT The fluorescence transient of Chlorella pyrenoidosa, excited by saturat- ing blue Chlorella pyrenoidosa the fluorescence transient exhibits a base level 0, a hump I at 50 msec. (at 1.5 X 104

Govindjee

368

LIGHT-INDUCED CHANGES IN THE FLUORESCENCE YIELD OF  

E-Print Network [OSTI]

LIGHT-INDUCED CHANGES IN THE FLUORESCENCE YIELD OF CHLOROPHYLL a IN VIVO II. CHLORELLA PYRENOIDOSA in Chlorella pyrenoidosa consists of a fast rise of the fluorescence yield from the level S (of the first wave photophosphorylation. INTRODUCTION The long-term fluorescence induction in Chlorella pyrenoidosa (second wave

Govindjee

369

Brief Communication 809 Photoactivation turns green fluorescent protein red  

E-Print Network [OSTI]

Brief Communication 809 Photoactivation turns green fluorescent protein red Michael B. Elowitz gene was first cloned, the Aequorea victoria green fluorescent protein (GFP) has become a powerful tool- wavelength (red) fluorescence has remained elusive. Here we describe a red-emitting, green

Elowitz, Michael

370

Status of the Silicon Photomultiplier Telescope FAMOUS for the Fluorescence Detection of UHECRs  

E-Print Network [OSTI]

An established technique for the measurement of ultra-high-energy-cosmic-rays is the detection of the fluorescence light induced in the atmosphere of the Earth, by means of telescopes equipped with photomultiplier tubes. Silicon photomultipliers (SiPMs) promise an increase in the photon detection efficiency which outperforms conventional photomultiplier tubes. In combination with their compact package, a moderate bias voltage of several ten volt and single photon resolution, the use of SiPMs can improve the energy and spatial resolution of air fluorescence measurements, and lead to a gain in information on the primary particle. Though, drawbacks like a high dark-noise-rate and a strong temperature dependency have to be managed. FAMOUS is a refracting telescope prototype instrumented with 64 SiPMs of which the main optical element is a Fresnel lens of 549.7 mm diameter and 502.1 mm focal length. The sensitive area of the SiPMs is increased by a special light collection system consisting of Winston cones. The t...

Niggemann, Tim; Brogueira, Pedro; Bueno, Antonio; Eichler, Hans Michael; Ferreira, Miguel; Hebbeker, Thomas; Lauscher, Markus; Mendes, Lus; Middendorf, Lukas; Navas, Sergio; Peters, Christine; Pimenta, Mrio; Ruiz, Angel; Schumacher, Johannes; Stephan, Maurice

2015-01-01T23:59:59.000Z

371

Demonstration of Recessed Downlight Technologies: Power and Illumination Assessment  

SciTech Connect (OSTI)

Solid state lighting (SSL), specifically light-emitting diodes (LED), has been advancing at a rapid pace, and there are presently multiple products available that serve as direct replacements for traditional luminaires. In this demonstration, conventional recessed lights in a conference room were used to compare conventional incandescent A-lamps, incandescent reflector R-lamps, dimming compact fluorescent lamps (CFL), to an LED replacement product. The primary focus during the study was on light delivered to the task plane as provided by the power required by the lighting system. Vertical illuminance, dimming range, and color shift are also important indicators of lighting quality and are discussed in the report. The results clearly showed that LEDs, with dimming-capable drivers, are much more efficient than incandescent and CFLs. Further, LEDs provide much smoother and consistent dimming than dimmable CFLs. On the potential negative side, it is important that the dimming switch be identified as compatible with the LED driver. A wide variety of dimmer switches are capable of dimming LEDs down to 15% of full light output, while select others can be capable of dimming LEDs down to 5%. In addition, LEDs can be intensive light sources, which can result in uncomfortable glare in some applications and to some occupants. Higher ceiling (9-foot or greater) or non-specular reflectors can act to alleviate the potential for glare.

Parker, Steven A.; Beeson, Tracy A.

2009-11-20T23:59:59.000Z

372

Industrial Lighting Techniques and New Developments  

E-Print Network [OSTI]

families customarily categorized in three major groupings Incandescent, Fluorescent, and High Intensity Discharge sources. In the incandescent family, halogen capsule 'technology has led to many new general lighting sources the 90-Watt and 45-Watt... Par 38 lamps deliver the same light output in the beam as conventional 150- and 75-Watt incandescent Par sources while using 40\\ less wattage and maintaining lamp life. By reducing voltage to the filament in halogen ~apsule sources, lamps can...

Colotti, M. A.

373

Compact Reversed-Field Pinch Reactors (CRFPR): preliminary engineering considerations  

SciTech Connect (OSTI)

The unique confinement physics of the Reversed-Field Pinch (RFP) projects to a compact, high-power-density fusion reactor that promises a significant reduction in the cost of electricity. The compact reactor also promises a factor-of-two reduction in the fraction of total cost devoted to the reactor plant equipment (i.e., fusion power core (FPC) plus support systems). In addition to operational and developmental benefits, these physically smaller systems can operate economically over a range of total power output. After giving an extended background and rationale for the compact fusion approaches, key FPC subsystems for the Compact RFP Reactor (CRFPR) are developed, designed, and integrated for a minimum-cost, 1000-MWe(net) system. Both the problems and promise of the compact, high-power-density fusion reactor are quantitatively evaluated on the basis of this conceptual design. The material presented in this report both forms a framework for a broader, more expanded conceptual design as well as suggests directions and emphases for related research and development.

Hagenson, R.L.; Krakowski, R.A.; Bathke, C.G.; Miller, R.L.; Embrechts, M.J.; Schnurr, N.M.; Battat, M.E.; LaBauve, R.J.; Davidson, J.W.

1984-08-01T23:59:59.000Z

374

The DPOSS II compact group survey: first spectroscopically confirmed candidates  

E-Print Network [OSTI]

This paper presents the results of a pilot redshift survey of 18 candidate compact groups from the distant DPOSS survey that extends the available surveys of compact groups of galaxies to z ~0.2 in redshift, mainly Hickson Compact Groups and Southern Compact Groups. The goal of our survey was to confirm group membership via redshift information and to measure the characteristic parameters of a representative, albeit small, sample of DPOSS survey groups. Of the 18 candidates observed, seven are found to be indeed isolated compact groups, i.e. groups with 3 or more concordant members and with no neighbouring known cluster, while 7 are chance projection configurations on the sky. Three remaining candidates, despite having 3 or more concordant member galaxies, are located in the neighbourhood of known clusters, while another candidate turned out to be a dense sub-condensation within Abell 0952. The median redshift of our 7 confirmed groups is z ~0.12, to be compared with a median redshift of 0.03 for the local sa...

Pompei, E; Iovino, A

2006-01-01T23:59:59.000Z

375

Underwater Lighting by Submerged Lasers and Incandescent Sources  

E-Print Network [OSTI]

books. For eX3.I11ple, equation (5.49.1) on page 107 of Glastone and Edlund's, "Elements of Nuclear Reactor

Duntley, Seibert Q

1971-01-01T23:59:59.000Z

376

How Energy-Efficient Light Bulbs Compare with Traditional Incandescents |  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsruc DocumentationP-SeriesFlickr FlickrGuidedCH2MLLC HistoryVeterans | UpdatesHowGetDoes a

377

Replacing Incandescent Lightbulbs and Ballasts | Department of Energy  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May JunDatastreamsmmcrcalgovInstrumentsrucLas ConchasPassive Solar HomePromisingStories » Removing nuclear waste,

378

DOE Requires Manufacturer and Labeler to Cease Sale of Incandescent  

Broader source: Energy.gov (indexed) [DOE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr May Jun Jul(Summary) "ofEarly Career Scientists'Montana. DOCUMENTSof Energy DOEDOEAVAILABLEDepartment ofHeld

379

Replacing Incandescent Lightbulbs and Ballasts | Department of Energy  

Energy Savers [EERE]

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious RankCombustion |EnergyonSupport0.pdf5Post-Holiday HolidayProcessRateofofRenewable EnergyRenewable

380

Compact multiwavelength transmitter module for multimode fiber optic ribbon cable  

DOE Patents [OSTI]

A compact multiwavelength transmitter module for multimode fiber optic ribbon cable, which couples light from an M.times.N array of emitters onto N fibers, where the M wavelength may be distributed across two or more vertical-cavity surface-emitting laser (VCSEL) chips, and combining emitters and multiplexer into a compact package that is compatible with placement on a printed circuit board. A key feature is bringing together two emitter arrays fabricated on different substrates--each array designed for a different wavelength--into close physical proximity. Another key feature is to compactly and efficiently combine the light from two or more clusters of optical emitters, each in a different wavelength band, into a fiber ribbon.

Deri, Robert J. (Pleasanton, CA); Pocha, Michael D. (Livermore, CA); Larson, Michael C. (Goleta, CA); Garrett, Henry E. (Livermore, CA)

2002-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "incandescent compact fluorescent" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Generating expansion model incorporating compact DC power flow equations  

SciTech Connect (OSTI)

This paper presents a compact method of incorporating the spatial dimension into the generation expansion problem. Compact DC power flow equations are used to provide real-power flow coordination equations. Using these equations the marginal contribution of a generator to th total system loss is formulated as a function of that generator`s output. Incorporating these flow equations directly into the MIP formulation of the generator expansion problem results in a model that captures a generator`s true net marginal cost, one that includes both the cost of generation and the cost of transport. This method contrasts with other methods that iterate between a generator expansion model and an optimal power flow model. The proposed model is very compact and has very good convergence performance. A case study with data from Kenya is used to provide a practical application to the model.

Nderitu, D.G.; Sparrow, F.T.; Yu, Z. [Purdue Inst. for Interdisciplinary Engineering Studies, West Lafayette, IN (United States)

1998-12-31T23:59:59.000Z

382

Anisotropic Compact Stars in $f(T)$ Gravity  

E-Print Network [OSTI]

This paper deals with the theoretical modeling of anisotropic compact stars in the framework of $f(T)$ theory of gravity, where $T$ is torsion scalar. To this end, we have used the exact solutions of Krori and Barua metric to a static spherically symmetric metric. The unknown constants involved in the Krori and Barua metric have been specified by using the masses and radii of compact stars 4$U$1820-30, Her X-1, SAX J 1808-3658. The physical properties of these stars have been analyzed in the framework of $f(T)$ theory. In this setting, we have checked the anisotropic behavior, regularity conditions, stability and surface redshift of the compact stars.

Abbas, G; Zubair, M

2015-01-01T23:59:59.000Z

383

Anisotropic Compact Stars in $f(G)$ Gravity  

E-Print Network [OSTI]

This paper is devoted to study the possibility of forming anisotropic compact stars in"modified Gauss-Bonnet, namely called as $f(G)$ theory of gravity which is one of the strong candidates, responsible for the accelerated expansion of the universe. For this purpose, we have used analytical solution of Krori and Barua metric to the Einstein field equations with anisotropic form of matter and power law model of $f(G)$ gravity. To determine the unknown constants in Krori and Barua metric, we have used the masses and radii of compact stars, 4$U$1820-30, Her X-1, SAX J 1808-3658. The physical behavior of these stars have been analyzed with the observational data. In this setting, we have checked all the regularity conditions and stability the compact stars 4$U$1820-30, Her X-1, SAX J 1808-3658.

G. Abbas; D. Momeni; M. Aamir Ali; R. Myrzakulov; S. Qaisar

2014-12-26T23:59:59.000Z

384

Anisotropic Compact Stars in $f(R)$ Gravity  

E-Print Network [OSTI]

In this paper we have investigated the possibility of forming of anisotropic compact stars in $f(R)$ gravity, one of the competent candidates of dark energy. To this end, we have applied the analytical solution of Krori and Barua metric to a static spherically symmetric spacetime in $f(R)$ gravity. The unknown constants in Krori and Barua metric have been determined by using masses and radii of class of compact stars like 4$U$1820-30, Her X-1, SAX J 1808-3658. The properties of these stars have been analyzes in detail. Furthermore, we have checked the regularity conditions, energy conditions, anisotropic behavior, stability and surface redshift of the compact stars 4$U$1820-30, Her X-1, SAX J 1808-3658.

M. Zubair; G. Abbas

2015-02-06T23:59:59.000Z

385

Anisotropic Compact Stars in $f(T)$ Gravity  

E-Print Network [OSTI]

This paper deals with the theoretical modeling of anisotropic compact stars in the framework of $f(T)$ theory of gravity, where $T$ is torsion scalar. To this end, we have used the exact solutions of Krori and Barua metric to a static spherically symmetric metric. The unknown constants involved in the Krori and Barua metric have been specified by using the masses and radii of compact stars 4$U$1820-30, Her X-1, SAX J 1808-3658. The physical properties of these stars have been analyzed in the framework of $f(T)$ theory. In this setting, we have checked the anisotropic behavior, regularity conditions, stability and surface redshift of the compact stars.

G. Abbas; Afshan Kanwal; M. Zubair

2015-01-22T23:59:59.000Z

386

Anisotropic Compact Stars in $f(G)$ Gravity  

E-Print Network [OSTI]

This paper is devoted to study the possibility of forming anisotropic compact stars in"modified Gauss-Bonnet, namely called as $f(G)$ theory of gravity which is one of the strong candidates, responsible for the accelerated expansion of the universe. For this purpose, we have used analytical solution of Krori and Barua metric to the Einstein field equations with anisotropic form of matter and power law model of $f(G)$ gravity. To determine the unknown constants in Krori and Barua metric, we have used the masses and radii of compact stars, 4$U$1820-30, Her X-1, SAX J 1808-3658. The physical behavior of these stars have been analyzed with the observational data. In this setting, we have checked all the regularity conditions and stability the compact stars 4$U$1820-30, Her X-1, SAX J 1808-3658.

Abbas, G; Ali, M Aamir; Myrzakulov, R; Qaisar, S

2015-01-01T23:59:59.000Z

387

Compact stars in the standard model - and beyond  

E-Print Network [OSTI]

In the context of the standard model of particle physics, there is a definite upper limit to the density of stable compact stars. However, if there is a deeper layer of constituents, below that of quarks and leptons, stability may be re-established far beyond this limiting density and a new class of compact stars could exist. These objects would cause gravitational lensing of white dwarfs and gamma-ray bursts, which might be observable as a diffraction pattern in the spectrum. Such observations could provide means for obtaining new clues about the fundamental particles and the origin of cold dark matter.

F. Sandin

2004-10-18T23:59:59.000Z

388

Infiltration of nickel into alumina compact by electrodeposition  

SciTech Connect (OSTI)

Ni metal was electrodeposited into pores of an alumina compact in the aqueous solution of nickel nitrate/urea/ethylene glycol/ammonium sulfate. The Ni{sup 2+} ions in pores of the alumina compact deposited in proportion to t{sup 0.45}-t{sup 0.61} of deposition time (t) on Au electrode sputtered on the alumina surface. The deposition rate of Ni was higher for direct current than pulsed current Nickel grew dendritically in the alumina pores.

Hirata, Yoshihiro; Kyoda, Hideharu; Iwamoto, Takayuki [Kagoshima Univ. (Japan)

1995-09-01T23:59:59.000Z

389

Compact two-beam push-pull free electron laser  

DOE Patents [OSTI]

An ultra-compact free electron laser comprising a pair of opposed superconducting cavities that produce identical electron beams moving in opposite directions such that each set of superconducting cavities accelerates one electron beam and decelerates the other electron beam. Such an arrangement, allows the energy used to accelerate one beam to be recovered and used again to accelerate the second beam, thus, each electron beam is decelerated by a different structure than that which accelerated it so that energy exchange rather than recovery is achieved resulting in a more compact and highly efficient apparatus.

Hutton, Andrew (Yorktown, VA)

2009-03-03T23:59:59.000Z

390

A study of hand tamper design for compaction of soils  

E-Print Network [OSTI]

Determination Standard Oven Dry Method versus Frying Pan Method Grain Size Distribution Curve Centerville Sand 34 Tamper Comparison Chart: Dry Density after 200 Blows per Square Foot of Layer Dry Density versus Compactive Effort Curve on 3. 0 Inch Square... of Utah revealed that a point exists at which an ultimate density is obtained, and any further increase in compaction effort results in lower than ultimate values. Shear Stress and Beari Ca acit If the resistance in a soil is exceeded by applied loads...

McDonough, Brian

1961-01-01T23:59:59.000Z

391

Plasma Frequency Shift Due to a Slowly Rotating Compact Star  

E-Print Network [OSTI]

We investigate the effects of a slowly rotating compact gravitational source on electron oscillations in a homogeneous electrically neutral plasma in the absence of an external electric or magnetic field. Neglecting the random thermal motion of the electrons we assume the gravitoelectromagnetic approximation to the general theory of relativity for the gravitational field. It is shown that there is a shift in the plasma frequency and hence in the dielectric constant of the plasma due to the gravitomagnetic force. We also give estimates for the difference in the frequency of radially transmitted electromagnetic signals for typical compact star candidates.

Babur M. Mirza; Hamid Saleem

2005-05-10T23:59:59.000Z

392

Compact Orthogonal NMR Field Sensor - Energy Innovation Portal  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation Proposed New SubstationCleanCommunity Involvement and Making aCompact soft x-rayEnergyCompact

393

Fluorescent Lamp Ballasts | Department of Energy  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page on Delicious Rank EERE:YearRound-UpHeat PumpRecordFederal7.pdfFlash_2010_-24.pdfOverview Flow Cells forFluorescent Lamp

394

Solid state laser media driven by remote nuclear powered fluorescence  

DOE Patents [OSTI]

An apparatus is provided for driving a solid state laser by a nuclear powered fluorescence source which is located remote from the fluorescence source. A nuclear reaction produced in a reaction chamber generates fluorescence or photons. The photons are collected from the chamber into a waveguide, such as a fiber optic waveguide. The waveguide transports the photons to the remote laser for exciting the laser.

Prelas, Mark A. (Columbia, MO)

1992-01-01T23:59:59.000Z

395

Optical Nanofibers for Manipulating and Probing Single-Atom Fluorescence  

E-Print Network [OSTI]

We demonstrate how optical nanofibers can be used to manipulate and probe single-atom fluorescence. We show that fluorescence photons from a very small number of atoms, average atom number of less than 0.1, around the nanofiber can readily be observed through single-mode optical fiber under resonant laser irradiation. We show also that optical nanofibers enable us to probe the van der Waals interaction between atoms and surface with high precision by observing the fluorescence excitation spectrum.

K. P. Nayak; P. N. Melentiev; M. Morinaga; Fam Le Kien; V. I. Balykin; K. Hakuta

2006-10-17T23:59:59.000Z

396

Optical Nanofibers for Manipulating and Probing Single-Atom Fluorescence  

E-Print Network [OSTI]

We demonstrate how optical nanofibers can be used to manipulate and probe single-atom fluorescence. We show that fluorescence photons from a very small number of atoms, average atom number of less than 0.1, around the nanofiber can readily be observed through single-mode optical fiber under resonant laser irradiation. We show also that optical nanofibers enable us to probe the van der Waals interaction between atoms and surface with high precision by observing the fluorescence excitation spectrum.

Nayak, K P; Morinaga, M; Le Kien, F; Balykin, V I; Hakuta, K; Kien, Fam Le

2006-01-01T23:59:59.000Z

397

Using fluorescence lifetime for discriminating detector afterpulsing in fluorescence-correlation spectroscopy  

E-Print Network [OSTI]

ACF , i.e., the second- order correlation function of the fluorescence intensity sig- nal. The physical meaning of the ACF is that it is propor- tional to the probability to detect, on average, a photon- nique, although the analysis does not explicitly identify single molecule detection events. On different

Enderlein, Jörg

398

Super-Resolution Fluorescence Nanoscopy Applied to Image Core...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

state of the photoswitching dyes do not absorb at wavelength of the fluorescence excitation. As a result, almost all the interfering fluorophores can be photobleached by the...

399

Time-resolved fluorescence decay measurements for flowing particles  

DOE Patents [OSTI]

Time-resolved fluorescence decay measurements for flowing particles. An apparatus and method for the measurement and analysis of fluorescence for individual cells and particles in flow are described, wherein the rapid measurement capabilities of flow cytometry and the robust measurement and analysis procedures of time-domain fluorescence lifetime spectroscopy are combined. A pulse-modulated cw laser is employed for excitation of the particles. The characteristics and the repetition rate of the excitation pulses can be readily adjusted to accommodate for fluorescence decays having a wide range of lifetimes.

Deka, Chiranjit (Miami, FL); Steinkamp, John A. (Los Alamos, NM)

1999-01-01T23:59:59.000Z

400

Time-resolved fluorescence decay measurements for flowing particles  

DOE Patents [OSTI]

Time-resolved fluorescence decay measurements are disclosed for flowing particles. An apparatus and method for the measurement and analysis of fluorescence for individual cells and particles in flow are described, wherein the rapid measurement capabilities of flow cytometry and the robust measurement and analysis procedures of time-domain fluorescence lifetime spectroscopy are combined. A pulse-modulated CW laser is employed for excitation of the particles. The characteristics and the repetition rate of the excitation pulses can be readily adjusted to accommodate for fluorescence decays having a wide range of lifetimes. 12 figs.

Deka, C.; Steinkamp, J.A.

1999-06-01T23:59:59.000Z

Note: This page contains sample records for the topic "incandescent compact fluorescent" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Fluorescent Multiblock ?-Conjugated Polymer Nanoparticles for In Vivo Tumor Targeting  

E-Print Network [OSTI]

Highly fluorescent multiblock conjugated polymer nanoparticles with folic acid surface ligands are highly effective for bioimaging and in vivo tumor targeting. The targeted nanoparticles were preferentially localized in ...

Ahmed, Eilaf

402

Fluorescent Pigments for High-Performance Cool Roofing and Facades...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

3 Berkeley Lab Heat Island Group physicist Paul Berdahl inserts precursor solution into a furnace. After boiling and then combustion, a fluorescent red pigment is formed. Image:...

403

aequorea green fluorescent: Topics by E-print Network  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

plants. Jim Haseloff Biology and Medicine Websites Summary: light, and an accessory green fluorescent protein (GFP), which accepts energy from aequorin and reImaging green...

404

Analysis of Time Series Using Compact Model-Based Descriptions  

E-Print Network [OSTI]

Analysis of Time Series Using Compact Model-Based Descriptions Hans-Peter Kriegel, Peer Kr this is a combination of the coefficients 1, . . . , 3 representing the three input time series using a function f-of-the-art compression methods. The results are visually presented in a very concise way so that the user can easily

Kriegel, Hans-Peter

405

MissionBased Compact The Commonwealth of Australia  

E-Print Network [OSTI]

;Page 2 CONTENTS Attachments A. Indicative list of Commonwealth Funding provided to the University which is administered by DEEWR and relevant to this Compact. B. List of Commonwealth Funding provided to the University and Workplace Relations and the University about Performance Funding. E. Copy of Commonwealth Grant Scheme

Viglas, Anastasios

406

Compact X-ray Light Source Workshop Report  

SciTech Connect (OSTI)

This report, produced jointly by EMSL and FCSD, is the result of a workshop held in September 2011 that examined the utility of a compact x-ray light source (CXLS) in addressing many scientific challenges critical to advancing energy science and technology.

Thevuthasan, Suntharampillai; Evans, James E.; Terminello, Louis J.; Koppenaal, David W.; Manke, Kristin L.; Plata, Charity

2012-12-01T23:59:59.000Z

407

Compact anhydrous HCl to aqueous HCl conversion system  

DOE Patents [OSTI]

The present invention is directed to an inexpensive and compact apparatus adapted for use with a .sup.196 Hg isotope separation process and the conversion of anhydrous HCl to aqueous HCl without the use of air flow to carry the HCl vapor into the converter system.

Grossman, Mark W. (Belmont, MA); Speer, Richard (S. Hamilton, MA)

1993-01-01T23:59:59.000Z

408

Carbon RRLs Carbon RRLs towards Ultra-compact HII Regions  

E-Print Network [OSTI]

Carbon RRLs Carbon RRLs towards Ultra-compact HII Regions Dana S. Balser D. Anish Roshi (Raman (Agnes Scott College) #12;Carbon RRLs Carbon Radio Recombination Lines (RRLs) NGC 2024 (Orion B) IC 1795 (W3) Palmer et al. (1967) #12;Carbon RRLs Photodissociation Regions (PDRs) Hollenbach & Tielens (1997

Balser, Dana S.

409

SURFING A WAVE TO COMPACT LASER TECHNOLOGY December 10 2007  

E-Print Network [OSTI]

to waves trailing behind a moving boat and small bunches of electrons can gather energy from the waveSURFING A WAVE TO COMPACT LASER TECHNOLOGY December 10 2007 New laser-based technology could laser pulses can be fired into plasma to create a wake and its huge electric fields can be harnessed

Strathclyde, University of

410

Compact Representation of Coordinated Sampling Policies for Body Sensor Networks  

E-Print Network [OSTI]

.Talukder@jpl.nasa.gov Abstract Embedded sensors of a Body Sensor Network need to efficiently utilize their energy resources Department of Electrical Engineering Los Angeles, CA 90089, USA 1-213-821-0871 {lius,raghu}@usc.edu 2 of a compact representation is feasible with little loss in performance. The global optimal policy is computed

Panangadan, Anand

411

DEFINITIONS OF COMPACTNESS AND THE AXIOM OF CHOICE ...  

E-Print Network [OSTI]

Apr 17, 2001 ... the United States and in France: using nets (Birkhoff, building on work by E. H. Moore and H. L. Smith), and ..... no countably infinite subset, and neither does its power set. It follows that (A, ...... [ho] P. Howard, Definitions of compactness, J. Symbolic Logic 55 (1990) 645655. ... University of Northern Iowa.

1910-20-32T23:59:59.000Z

412

Wavelet Occupancy Grids: a Method for Compact Map Building  

E-Print Network [OSTI]

Wavelet Occupancy Grids: a Method for Compact Map Building Manuel Yguel, Olivier Aycard for multi-resolution map building based on wavelets, which we call the wavelet occupancy grid (WavOG). Pai representation and data storage for large maps, under the constraints of multi-sensor real-time updates

Paris-Sud XI, Universit de

413

ULTRA-COMPACT ACCELERATOR TECHNOLOGIES FOR APPLICATION IN NUCLEAR TECHNIQUES  

SciTech Connect (OSTI)

We report on compact accelerator technology development for potential use as a pulsed neutron source quantitative post verifier. The technology is derived from our on-going compact accelerator technology development program for radiography under the US Department of Energy and for a clinic sized compact proton therapy systems under an industry sponsored Cooperative Research and Development Agreement. The accelerator technique relies on the synchronous discharge of a prompt pulse generating stacked transmission line structure with the beam transit. The goal of this technology is to achieve {approx}10 MV/m gradients for 10s of nanoseconds pulses and to {approx}100 MV/m gradients for {approx}1 ns systems. As a post verifier for supplementing existing x-ray equipment, this system can remain in a charged, stand-by state with little or no energy consumption. We detail the progress of our overall component development effort with the multilayer dielectric wall insulators (i.e., the accelerator wall), compact power supply technology, kHz repetition-rate surface flashover ion sources, and the prompt pulse generation system consisting of wide-bandgap switches and high performance dielectric materials.

Sampayan, S; Caporaso, G; Chen, Y; Carazo, V; Falabella, S; Guethlein, G; Guse, S; Harris, J R; Hawkins, S; Holmes, C; Krogh, M; Nelson, S; Paul, A C; Pearson, D; Poole, B; Schmidt, R; Sanders, D; Selenes, K; Sitaraman, S; Sullivan, J; Wang, L; Watson, J

2009-06-11T23:59:59.000Z

414

A New Compact Multichannel Receiver for Underwater Wireless Communication Networks  

E-Print Network [OSTI]

size of the proposed receiver makes it particularly useful for small unmanned underwater vehicles1 A New Compact Multichannel Receiver for Underwater Wireless Communication Networks Ali Abdi of the particle velocity, in addition to the pressure, multichannel reception can be accomplished in underwater

Abdi, Ali

415

MIXING RANK-ONE ACTIONS OF LOCALLY COMPACT ABELIAN GROUPS  

E-Print Network [OSTI]

MIXING RANK-ONE ACTIONS OF LOCALLY COMPACT ABELIAN GROUPS Alexandre I. Danilenko and Cesar E. Silva that such transformations are mixing of all orders [Ka], [Ry1] and have minimal self-joinings of all orders [Ki], [Ry1 this progress, not so many concrete examples of rank-one mixing ac- tions are known. Most of them were obtained

Silva, Cesar E.

416

Design and Application of Low Compaction Energy Concrete for  

E-Print Network [OSTI]

Design and Application of Low Compaction Energy Concrete for Use in Slip-form Concrete Paving of cement pastes and the green strength of concretes Slipform self-consolidating concrete (SFSCC) requires sufficient flowability in order to consolidate without the use of internal vibration. However, this concrete

417

Introduction to Compact Riemann Surfaces Alexander I. Bobenko  

E-Print Network [OSTI]

1 Introduction to Compact Riemann Surfaces Alexander I. Bobenko Institut f¨ur Mathematik more self contained. In particular we will deal with classical descriptions of Riemann surfaces, and uniformization techniques. Motivated by the concrete point of view on Riemann surfaces of this book we choose

Bobenko, Alexander I.

418

Disk-shaped Compact Tension Test for Asphalt Concrete Fracture  

E-Print Network [OSTI]

Disk-shaped Compact Tension Test for Asphalt Concrete Fracture by M.P.Wagoner, W.G. Buttlar and G geometry is the ability to test cylindrical cores obtained from in-place asphalt concrete pavements finalizing the specimen geometry, a typical asphalt concrete surface mixture was tested at various

Paulino, Glaucio H.

419

Recent progress on the Compact Ignition Tokamak (CIT)  

SciTech Connect (OSTI)

This report describes work done on the Compact Ignition Tokamak (CIT), both at the Princeton Plasma Physics Laboratory (PPPL) and at other fusion laboratories in the United States. The goal of CIT is to reach ignition in a tokamak fusion device in the mid-1990's. Scientific and engineering features of the design are described, as well as projected cost and schedule.

Ignat, D.W.

1987-01-01T23:59:59.000Z

420

Embedding the bicyclic semigroup into countably compact topological semigroups  

E-Print Network [OSTI]

We study algebraic and topological properties of topological semigroups containing a copy of the bicyclic semigroup $C(p,q)$. We prove that each topological semigroup $S$ with pseudocompact square contains no dense copy of $C(p,q)$. On the other hand, we construct a consistent example of a Tychonov countably compact semigroup containing a copy of $C(p,q)$.

Banakh, Taras; Gutik, Oleg

2008-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "incandescent compact fluorescent" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

COSMOLOGICAL SIMULATIONS OF MASSIVE COMPACT HIGH-z GALAXIES  

SciTech Connect (OSTI)

In order to investigate the structure and dynamics of the recently discovered massive (M{sub *} {approx}> 10{sup 11} M{sub sun}) compact z {approx} 2 galaxies, cosmological hydrodynamical/N-body simulations of a {approx}50,000 Mpc{sup 3} comoving (Lagrangian), proto-cluster region have been undertaken. At z = 2, the highest resolution simulation contains {approx}5800 resolved galaxies, of which 509, 27, and 5 have M{sub *}>10{sup 10} M{sub sun}, M{sub *}>10{sup 11} M{sub sun}, and M{sub *}>4 x 10{sup 11} M{sub sun}, respectively. Total stellar masses, effective radii, and characteristic stellar densities have been determined for all galaxies. At z = 2, for the definitely well-resolved mass range of M{sub *} {approx}> 10{sup 11} M{sub sun}, we fit the relation R{sub eff} = R{sub eff,12} M {sup 1/3}{sub *,12} to the data, where M{sub *,12} is the total stellar mass in units of 10{sup 12} M{sub sun}. This yields R{sub eff,12} = (1.20 {+-} 0.04) kpc, in line with observational findings for compact z {approx} 2 galaxies, though somewhat more compact than the observed average. The only line-of-sight velocity dispersion measured for a z {approx} 2 compact galaxy is very large, {sigma}{sub *,p} = 510{sup +165}{sub -95} km s{sup -1}. This value can be matched at about the 1{sigma} level, although a somewhat larger mass than the estimated M{sub *} {approx_equal} 2 x 10{sup 11} M{sub sun} is indicated. For the above mass range, the galaxies have an average axial ratio (b/a) = 0.64 {+-} 0.02 with a dispersion of 0.1, and an average rotation to one-dimensional velocity-dispersion ratio (v/{sigma}) = 0.46 {+-} 0.06 with a dispersion of 0.3, and a maximum value of v/{sigma} {approx_equal} 1.1. Both rotation and velocity anisotropy contribute significantly in flattening the compact galaxies. Some of the observed compact galaxies appear flatter than any of the simulated galaxies. Finally, it is found that the massive compact galaxies are strongly baryon dominated in their inner parts, with typical dark matter mass fractions of order only 20% inside of r = 2 R{sub eff}.

Sommer-Larsen, J.; Toft, S., E-mail: jslarsen@astro.ku.d, E-mail: sune@dark-cosmology.d [Dark Cosmology Centre, Niels Bohr Institute, University of Copenhagen, Juliane Mariesvej 30, DK-2100 Copenhagen (Denmark)

2010-10-01T23:59:59.000Z

422

Modeling of highly loaded fluorescent lamps  

SciTech Connect (OSTI)

Numerical modeling of the positive column of fluorescent lamps under conditions of high current density are of current interest, particularly in view of recent developments in electrodeless lamps. Current models tend to overestimate radiation output, and consequently the maintenance electric field in these discharges. Under highly loaded conditions, mercury-rare gas fluorescent lamps exhibit strong mercury depletion on axis (cataphoresis), and an understanding of resonance radiation transport under these conditions is therefore vital to the development of models with a predictive capability. The authors have explored the effect of radial cataphoresis on resonance radiation trapping for situations in which the radiation transport is dominated by foreign gas broadening, Doppler broadening, or resonance collisional broadening of the spectral line. Several different production rates per unit volume of resonance (excited) atoms have also been studied. It is advantageous in many cases to parameterize the trapped decay rate in terms of the total number of ground state atoms in the positive column independent of their radial distribution. The results of this work have been included in a numerical model of the positive column and the predicted influence on discharge parameters will be presented for cases of interest to highly loaded lamps.

Lister, G.G.; Lawler, J.E.; Curry, J.J.

1999-07-01T23:59:59.000Z

423

Essays in Public Economics and Development  

E-Print Network [OSTI]

adopt compact fluorescent light bulbs (CFLs), and possibleof compact fluorescent light bulbs (CFLs) from PROCEL, andAdoption of compact fluorescent light bulbs In the PROCEL

Gerard, Francois

2013-01-01T23:59:59.000Z

424

Bringing climate change down to earth : science and participation in Canadian and Australian climate change campaigns  

E-Print Network [OSTI]

bulbs with compact fluorescent bulbs. This led to a fair bitsuch as compact fluorescent bulbs, low-flow showerheads, andtechnologies: compact fluorescent light bulbs, energy saving

Padolsky, Miriam Elana

2006-01-01T23:59:59.000Z

425

Delivering Energy Efficiency to Middle Income Single Family Households  

E-Print Network [OSTI]

system CFL Compact Fluorescent Light Bulb IAQ Indoor Airdiscount compact fluorescent light bulbs (CFLs) or providediscount compact fluorescent light bulbs (CFLs) or provide

Zimring, Mark

2012-01-01T23:59:59.000Z

426

Ceramographic Examinations of Irradiated AGR-1 Fuel Compacts  

SciTech Connect (OSTI)

The AGR 1 experiment involved irradiating 72 cylindrical fuel compacts containing tri-structural isotropic (TRISO)-coated particles to a peak burnup of 19.5% fissions per initial metal atom with no in-pile failures observed out of almost 300,000 particles. Six irradiated AGR 1 fuel compacts were selected for microscopy that span a range of irradiation conditions (temperature, burnup, and fast fluence). These six compacts also included all four TRISO coating variations irradiated in the AGR experiment. The six compacts were cross-sectioned both transversely and longitudinally, mounted, ground, and polished after development of careful techniques for preserving particle structures against preparation damage. From 36 to 79 particles within each cross section were exposed near enough to midplane for optical microscopy of kernel, buffer, and coating behavior. The microstructural analysis focused on kernel swelling and porosity, buffer densification and fracture, debonding between the buffer and inner pyrolytic carbon (IPyC) layers, and fractures in the IPyC and SiC layers. Three basic particle morphologies were established according to the extent of bonding between the buffer and IPyC layers: complete debonding along the interface (Type A), no debonding along the interface (Type B), and partial debonding (Type AB). These basic morphologies were subdivided according to whether the buffer stayed intact or fractured. The resulting six characteristic morphologies were used to classify particles within each cross section, but no spatial patterns were clearly observed in any of the cross-sectional morphology maps. Although positions of particle types appeared random within compacts, examining a total of 931 classified particles allowed other relationships among morphological types to be established.

Paul Demkowicz; Scott Ploger; John Hunn; Jay S. Kehn

2012-09-01T23:59:59.000Z

427

Ceramographic Examinations of Irradiated AGR-1 Fuel Compacts  

SciTech Connect (OSTI)

The AGR 1 experiment involved irradiating 72 cylindrical fuel compacts containing tri-structural isotropic (TRISO)-coated particles to a peak burnup of 19.5% fissions per initial metal atom with no in-pile failures observed out of almost 300,000 particles. Five irradiated AGR 1 fuel compacts were selected for microscopy that span a range of irradiation conditions (temperature, burnup, and fast fluence). These five compacts also included all four TRISO coating variations irradiated in the AGR experiment. The five compacts were cross-sectioned both transversely and longitudinally, mounted, ground, and polished after development of careful techniques for preserving particle structures against preparation damage. Approximately 40 to 80 particles within each cross section were exposed near enough to mid-plane for optical microscopy of kernel, buffer, and coating behavior. The microstructural analysis focused on kernel swelling and porosity, buffer densification and fracture, debonding between the buffer and inner pyrolytic carbon (IPyC) layers, and fractures in the IPyC and SiC layers. Three basic particle morphologies were established according to the extent of bonding between the buffer and IPyC layers: complete debonding along the interface (Type A), no debonding along the interface (Type B), and partial debonding (Type AB). These basic morphologies were subdivided according to whether the buffer stayed intact or fractured. The resulting six characteristic morphologies were used to classify particles within each cross section, but no spatial patterns were clearly observed in any of the cross-sectional morphology maps. Although positions of particle types appeared random within compacts, examining a total of 830 classified particles allowed other relationships among morphological types to be established.

Paul Demkowicz; Scott Ploger; John Hunn

2012-05-01T23:59:59.000Z

428

High-volume natural volcanic pozzolan and limestone powder as partial replacements for portland cement in self-compacting and sustainable concrete  

E-Print Network [OSTI]

the resulting self-compacting concrete (SCC). Petrographicity, which satisfy self-compacting concrete criteria withoutcement in self-compacting and sustainable concrete K. Celik

2014-01-01T23:59:59.000Z

429

Northwest Interstate Compact on Low-Level Radioactive Waste Management (Multiple States)  

Broader source: Energy.gov [DOE]

The Northwest Interstate Compact on Low-Level Radioactive Waste Management, enacted in 1981, was ratified by Congress in 1985. The Compact is a cooperative effort of the party states to protect...

430

Compaction Effects on Uniformity, Moisture Diffusion, and Mechanical Properties of Asphalt Pavements  

E-Print Network [OSTI]

Field compaction of asphalt mixtures is an important process that influences performance of asphalt pavements; however there is very little effort devoted to evaluate the influence of compaction on the uniformity and properties of asphalt mixtures...

Kassem, Emad Abdel-Rahman Ahmed

2011-08-08T23:59:59.000Z

431

Acoustic emission and compaction creep of quartz sand at subcritical stress  

E-Print Network [OSTI]

Time-dependent fluid-assisted mechanisms such as stress-induced dissolution and subcritical crack growth play an important role in porosity reduction and compaction of granular material in nature. Previous compaction creep experiments on loosely...

Lenz, Steven Christopher

2002-01-01T23:59:59.000Z

432

E-Print Network 3.0 - advanced compact accelerator Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Physics 27 By-Products Utilization Summary: Center for By-Products Utilization SELF-COMPACTING CONCRETE (SCC) OR SELF- LEVELING CONCRETE (SLC... - MILWAUKEE 12;2 SELF-COMPACTING...

433

Safe and compact ammonia storage/delivery systems for SCR-DeNOX...  

Office of Environmental Management (EM)

Safe and compact ammonia storagedelivery systems for SCR-DeNOX in automotive units Safe and compact ammonia storagedelivery systems for SCR-DeNOX in automotive units Presentation...

434

HIgh Rate X-ray Fluorescence Detector  

SciTech Connect (OSTI)

The purpose of this project was to develop a compact, modular multi-channel x-ray detector with integrated electronics. This detector, based upon emerging silicon drift detector (SDD) technology, will be capable of high data rate operation superior to the current state of the art offered by high purity germanium (HPGe) detectors, without the need for liquid nitrogen. In addition, by integrating the processing electronics inside the detector housing, the detector performance will be much less affected by the typically noisy electrical environment of a synchrotron hutch, and will also be much more compact than current systems, which can include a detector involving a large LN2 dewar and multiple racks of electronics. The combined detector/processor system is designed to match or exceed the performance and features of currently available detector systems, at a lower cost and with more ease of use due to the small size of the detector. In addition, the detector system is designed to be modular, so a small system might just have one detector module, while a larger system can have many ?? you can start with one detector module, and add more as needs grow and budget allows. The modular nature also serves to simplify repair. In large part, we were successful in achieving our goals. We did develop a very high performance, large area multi-channel SDD detector, packaged with all associated electronics, which is easy to use and requires minimal external support (a simple power supply module and a closed-loop water cooling system). However, we did fall short of some of our stated goals. We had intended to base the detector on modular, large-area detectors from Ketek GmbH in Munich, Germany; however, these were not available in a suitable time frame for this project, so we worked instead with pnDetector GmbH (also located in Munich). They were able to provide a front-end detector module with six 100 m^2 SDD detectors (two monolithic arrays of three elements each) along with associated preamplifiers; these detectors surpassed the performance we expected to get from the Ketek detectors, however they are housed in a sealed module, which does not offer the ease of repair and expandability we??d hoped to achieve with the Ketek SDD??s. Our packaging efforts were quite successful, as we came up with a very compact way to mount the detector and to house the associated electronics, as well as a very effective way to reliably take out the heat (from the electronics as well as the detector??s Peltier coolers) without risk of condensation and without external airflow or vibration, which could create problems for the target applications. While we were able to design compact processing electronics that fit into the detector assembly, they are still at the prototype stage, and would require a significant redesign to achieve product status. We have not yet tested this detector at a synchrotron facility; we do still plan on working with some close contacts at the nearby Stanford Synchrotron Radiation Laboratory (SSRL) to get some testing with the beam (using existing commercial electronics for readout, as the integrated processor is not ready for use).

Grudberg, Peter Matthew [XIA LLC

2013-04-30T23:59:59.000Z

435

Max Tech and Beyond: Fluorescent Lamps  

SciTech Connect (OSTI)

Fluorescent lamps are the most widely used artificial light source today, responsible for approximately 70% of the lumens delivered to our living spaces globally. The technology was originally commercialized in the 1930's, and manufacturers have been steadily improving the efficacy of these lamps over the years through modifications to the phosphors, cathodes, fill-gas, operating frequency, tube diameter and other design attributes. The most efficient commercially available fluorescent lamp is the 25 Watt T5 lamp. This lamp operates at 114-116 lumens per watt while also providing good color rendering and more than 20,000 hours of operating life. Industry experts interviewed indicated that while this lamp is the most efficient in the market today, there is still a further 10 to 14% of potential improvements that may be introduced to the market over the next 2 to 5 years. These improvements include further developments in phosphors, fill-gas, cathode coatings and ultraviolet (UV) reflective glass coatings. The commercialization of these technology improvements will combine to bring about efficacy improvements that will push the technology up to a maximum 125 to 130 lumens per watt. One critical issue raised by researchers that may present a barrier to the realization of these improvements is the fact that technology investment in fluorescent lamps is being reduced in order to prioritize research into light emitting diodes (LEDs) and ceramic metal halide high intensity discharge (HID) lamps. Thus, it is uncertain whether these potential efficacy improvements will be developed, patented and commercialized. The emphasis for premium efficacy will continue to focus on T5 lamps, which are expected to continue to be marketed along with the T8 lamp. Industry experts highlighted the fact that an advantage of the T5 lamp is the fact that it is 40% smaller and yet provides an equivalent lumen output to that of a T8 or T12 lamp. Due to its smaller form factor, the T5 lamp contains less material (i.e., glass, fill gas and phosphor), and has a higher luminance, enabling fixtures to take advantage of the smaller lamp size to improve the optics and provide more efficient overall system illuminance. In addition to offering the market a high-quality efficacious light source, another strong value proposition of fluorescent lighting is its long operating life. In today's market, one manufacturer is offering fluorescent lamps that have a rated life of 79,000 hours - which represents 18 years of service at 12 hours per day, 365 days per year. These lamps, operated using a long-life ballast specified by the manufacturer, take advantage of improvements in cathode coatings, fill gas chemistry and pressure to extend service life by a factor of four over conventional fluorescent lamps. It should be noted that this service life is also longer (approximately twice as long) as today's high-quality LED products. The fluorescent market is currently focused on the T5 and T8 lamp diameters, and it is not expected that other diameters would be introduced. Although T8 is a more optimal diameter from an efficacy perspective, the premium efficiency and optimization effort has been focused on T5 lamps because they are 40% smaller than T8, and are designed to operate at a higher temperature using high-frequency electronic ballasts. The T5 lamp offers savings in terms of materials, packaging and shipping, as well as smaller fixtures with improved optical performance. Manufacturers are actively researching improvements in four critical areas that are expected to yield additional efficacy improvements of approximately 10 to 14 percent over the next five years, ultimately achieving approximately 130 lumens per watt by 2015. The active areas of research where these improvements are anticipated include: (1) Improved phosphors which continue to be developed and patented, enabling higher efficacies as well as better color rendering and lumen maintenance; (2) Enhanced fill gas - adjusting proportions of argon, krypton, neon and xenon to optimize performance, while also m

Scholand, Michael

2012-04-01T23:59:59.000Z

436

E-Print Network 3.0 - aeropropulsion compact lightweight Sample...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

has developed a true 3- component technique, no calibration, compact instrumentation... Hydro--propulsion Aeropropulsion Aero--propulsionpropulsion Micro jet...

437

Improved ``Optical Highlighter'' Probes Derived from Discosoma Red Fluorescent Protein  

E-Print Network [OSTI]

, Minneapolis, Minnesota ABSTRACT The tetrameric red fluorescent protein, DsRed, undergoes a rapid red to green-emitting species of DsRed and an enhancement of emission from the ``immature'' green species, likely caused by dequenching of fluorescence resonance energy transfer occurring within the protein tetramer. Here, we have

Marchant, Jonathan

438

A monomeric red fluorescent protein Robert E. Campbell*, Oded Tour*  

E-Print Network [OSTI]

A monomeric red fluorescent protein Robert E. Campbell*, Oded Tour* , Amy E. Palmer*, Paul A, and the obligate tetramerization of the red fluorescent protein from Discosoma (DsRed). Although the weak, the obligate tet- ramerization of DsRed has greatly hindered its use as a genetically encoded fusion tag. We

Tsien, Roger Y.

439

Gregorio Weber International Prize in Biological Fluorescence 2008  

E-Print Network [OSTI]

Gregorio Weber International Prize in Biological Fluorescence 2008 The Gregorio Weber International Prize in Biological Fluorescence (Weber Prize) is awarded for research related to a doctoral (or finalists. Weber Prizes were awarded in 2002 and 2005. The third Weber Prize will be awarded in 2008

Weber, David J.

440

Fluorescent Sensors for Zn2+ Based on a Fluorescein Platform  

E-Print Network [OSTI]

Fluorescent Sensors for Zn2+ Based on a Fluorescein Platform: Synthesis, Properties fluorescent sensors for Zn2+ that utilize fluorescein as a reporting group, Zinpyr-1 and Zinpyr-2, have been. Both Zinpyr sensors have excitation and emission wavelengths in the visible range (500 nm

Tsien, Roger Y.

Note: This page contains sample records for the topic "incandescent compact fluorescent" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Development and Application of Fluorescent SDF-1 Derivatives Ryo Masuda,  

E-Print Network [OSTI]

#12;1 Development and Application of Fluorescent SDF-1 Derivatives Ryo Masuda, Shinya Oishi of Medicine, 2-1 Seiryocho, Aoba-ku, Sendai 980-8575, Japan. #12;2 Abstract Background: SDF-1/CXCR4 signaling, structure-activity relationship analyses of fluorescent SDF-1 derivatives were carried out. Results: Several

Takada, Shoji

442

Multicontrast photoacoustic in vivo imaging using near-infrared fluorescent  

E-Print Network [OSTI]

Multicontrast photoacoustic in vivo imaging using near-infrared fluorescent proteins Arie Krumholz1 the application of two spectrally distinct near-infrared fluorescent proteins, iRFP670 and iRFP720, engineered-tissue PAT, probes absorbing in the near-infrared (NIR) spectral range are desirable. In the NIR optical

Verkhusha, Vladislav V.

443

Full-wavelet approach for fluorescence diffuse optical tomography  

E-Print Network [OSTI]

Full-wavelet approach for fluorescence diffuse optical tomography with structured illumination Leonardo da Vinci 32, I-20133 Milan, Italy 3 Centre for Medical Image Computing, University College London); published October 28, 2010 We present a fast reconstruction method for fluorescence optical tomography

Boyer, Edmond

444

Application of Quantitative Fluorescence and Absorption-Edge  

E-Print Network [OSTI]

Application of Quantitative Fluorescence and Absorption-Edge Computed Microtomography to Image, Chicago, Illinois 60637 This paper shows that synchrotron-based fluorescence and absorption-edge computed, which had a well-correlated metal coating. Absorption-edge CMT showed the three-dimensional distribution

Sparks, Donald L.

445

Prediction of Asphalt Mixture Compactability from Mixture, Asphalt, and Aggregate Properties  

E-Print Network [OSTI]

. Predicted Plot of CV Neural Net of Entire Data Set for a ............................ 50 Figure 32. Predicted Plot of CV Neural Net of Entire Data Set for AV Nini ................... 51 Figure 33. a versus Predicted a... ................................................... 24 Table 5 HMA Mixing and Compaction Temperatures ............................................. 27 Table 6 Compaction Parameters a, c, and AV Nini ................................................... 38 Table 7 Compaction Parameters m1, m2...

Muras, Andrew J.

2010-07-14T23:59:59.000Z

446

CorrectedProof DETERMINATION OF THE RHEOLOGICAL PARAMETERS OF SELF-COMPACTING  

E-Print Network [OSTI]

CorrectedProof DETERMINATION OF THE RHEOLOGICAL PARAMETERS OF SELF-COMPACTING CONCRETE MATRIX USING version: 7.7.2010 Abstract: The classification of a concrete mixture as self-compacting (SCC) is performed time with viscosity. Key words: self compacting concrete, rheology, slump flow, yield stress

Georgiou, Georgios

447

Mechanical properties of self-compacting concrete reinforced with polypropylene fibres  

E-Print Network [OSTI]

Mechanical properties of self-compacting concrete reinforced with polypropylene fibres O. Gencel*1 of workability. Self-compacting concrete (SCC) is an innovative concrete that is able to flow under its own engineers to incorporate many materials into it. A variety of types of concrete exist.7 Self-compacting

North Texas, University of

448

Design and Development of Integrated Compact Multiphase Separation System (CMSS)  

SciTech Connect (OSTI)

The petroleum industry has relied in the past mainly on conventional vessel-type separators, which are bulky, heavy and expensive, to process wellhead production of oil-water-gas flow. Economic and operational pressures continue to force the petroleum industry to seek less expensive and more efficient separation alternatives in the form of compact separators. The compact dimensions, smaller footprint and lower weight of compact separators have a potential for cost savings to the industry, especially in offshore and subsea applications. Also, compact separators reduce the inventory of hydrocarbons significantly, which is critical for environmental This report presents a brief overview of the activities and tasks accomplished during the Budget Period II (October 09, 2004-April 30, 2006) of the DOE project titled ''Design and Development of Integrated Compact Multiphase Separation System (CMSS{copyright})''. An executive summary is presented initially followed by the tasks of the current budget period. Then, detailed description of the experimental and modeling investigations are presented. Subsequently, the technical and scientific results of the activities of this project period are presented with discussions. The findings of this investigation are summarized in the ''Conclusions'' section In this investigation, the concept of CMSS{copyright} has been developed and is proven through simulation studies and validated by experimental data. As part of the second phase of the project (Budget Period II--10/09/2004-04/30/2006) experimental investigation of the integrated CMSS{copyright} for different configurations has been conducted in order to evaluate the performance of the individual separation components, and determine how they will affect the performance of each other when integrated in the CMSS{copyright}. An intelligent control system is also developed to improve the total system efficiency of Compact Multiphase Separation System (CMSS{copyright}). In mature oil fields, water handling poses a huge problem. Thus water knock out at the earliest stage helps in significant cost savings during handling, separation and transportation of oil. One of the objectives of the CMSS{copyright} configuration is to knock out free water from the upstream fluids. The results from theoretical and experimental studies show that Free Water Knock Out (FWKO) CMSS{copyright} system can be readily deployed in the field using the control system strategies designed, implemented and tested in this study.

Ram S. Mohan; Ovadia Shoham

2006-04-30T23:59:59.000Z

449

Fluorescence in nonlocal dissipative periodic structures  

E-Print Network [OSTI]

We present an approach for the description of fluorescence from optically active material embedded in layered periodic structures. Based on an exact electromagnetic Green's tensor analysis, we determine the radiative properties of emitters such as the local photonic density of states, Lamb shifts, line widths etc. for a finite or infinite sequence of thin alternating plasmonic and dielectric layers. In the effective medium limit, these systems may exhibit hyperbolic dispersion relations so that the large wave-vector characteristics of all constituents and processes become relevant. These include the finite thickness of the layers, the nonlocal properties of the constituent metals, and local-field corrections associated with an emitter's dielectric environment. In particular, we show that the corresponding effects are non-additive and lead to considerable modifications of an emitter's luminescence properties.

Francesco Intravaia; Kurt Busch

2015-02-24T23:59:59.000Z

450

SIMULTANEOUS MEASUREMENT OF CIRCULAR DICHROISM AND FLUORESCENCE POLARIZATION ANISOTROPY.  

SciTech Connect (OSTI)

Circular dichroism and fluorescence polarization anisotropy are important tools for characterizing biomolecular systems. Both are used extensively in kinetic experiments involving stopped- or continuous flow systems as well as titrations and steady-state spectroscopy. This paper presents the theory for determining circular dichroism and fluorescence polarization anisotropy simultaneously, thus insuring the two parameters are recorded under exactly the same conditions and at exactly the same time in kinetic experiments. The approach to measuring circular dichroism is that used in almost all conventional dichrographs. Two arrangements for measuring fluorescence polarization anisotropy are described. One uses a single fluorescence detector and signal processing with a lock-in amplifier that is similar to the measurement of circular dichroism. The second approach uses classic ''T'' format detection optics, and thus can be used with conventional photon-counting detection electronics. Simple extensions permit the simultaneous measurement of the absorption and excitation intensity corrected fluorescence intensity.

SUTHERLAND,J.C.

2002-01-19T23:59:59.000Z

451

Fracture toughness measurements with subsize disk compact specimens  

SciTech Connect (OSTI)

Special fixtures and test methods have been developed for testing small disk compact specimens (1.25 mm diam by 4.6 mm thick). Specimens of European type 316L austenitic stainless steel were irradiated to damage levels of about 3 dpa at nominal irradiation temperatures of either 90 or 250 C and tested over a temperature range from 20 to 250 C. Results show that irradiation to this dose level at these temperatures reduces the fracture toughness but the toughness remains quite high. The toughness decreases as the test temperature increases. Irradiation at 250 C is more damaging than at 90 C, causing larger decreases in the fracture toughness. The testing shows that it is possible to generate useful fracture toughness data with a small disk compact specimens.

Alexander, D.J.

1994-12-31T23:59:59.000Z

452

Compact and mobile high resolution PET brain imager  

DOE Patents [OSTI]

A brain imager includes a compact ring-like static PET imager mounted in a helmet-like structure. When attached to a patient's head, the helmet-like brain imager maintains the relative head-to-imager geometry fixed through the whole imaging procedure. The brain imaging helmet contains radiation sensors and minimal front-end electronics. A flexible mechanical suspension/harness system supports the weight of the helmet thereby allowing for patient to have limited movements of the head during imaging scans. The compact ring-like PET imager enables very high resolution imaging of neurological brain functions, cancer, and effects of trauma using a rather simple mobile scanner with limited space needs for use and storage.

Majewski, Stanislaw (Yorktown, VA); Proffitt, James (Newport News, VA)

2011-02-08T23:59:59.000Z

453

Air Fluorescence Relevant for Cosmic-Ray Detection - Summary of the 5th Fluorescence Workshop, El Escorial 2007  

E-Print Network [OSTI]

High-energy cosmic rays with energies exceeding $10^{17}$ eV are frequently observed by measurements of the fluorescence light induced by air showers. A major contribution to the systematic uncertainties of the absolute energy scale of such experiments is the insufficient knowledge of the fluorescence light yield of electrons in air. The aim of the 5th Fluorescence Workshop was to bring together experimental and theoretical expertise to discuss the latest progress on the investigations of the fluorescence light yield. The results of the workshop will be reviewed as well as the present status of knowledge in this field. Emphasis is given to the fluorescence light yield important for air shower observations and its dependence on atmospheric parameters, like pressure, temperature, and humidity. The effects of the latest results on the light observed from air showers will be discussed.

Fernando Arqueros; Joerg R. Hoerandel; Bianca Keilhauer

2008-07-24T23:59:59.000Z

454

Compact gas-insulated transformer. Fourteenth quarterly report  

SciTech Connect (OSTI)

Objective is to develop a compact, more efficient, quieter transformer which does not rely on mineral oil insulation. Compressed SF/sub 6/ is used as the external insulation and polymer film as the insulation between turns. A separate liquid cooling system is also provided. This document reports progress made in design, mechanical, dielectric, short circuit, thermal, materials, prototype, accessories, commercialization, and system studies. (DLC)

Not Available

1983-08-01T23:59:59.000Z

455

Compact Refractive Imaging Spectrometer Designs Utilizing Immersed Gratings  

DOE Patents [OSTI]

A compact imaging spectrometer comprising an entrance slit for directing light, a first means for receiving the light and focusing the light, an immersed diffraction grating that receives the light from the first means and defracts the light, a second means for receiving the light from the immersed diffraction grating and focusing the light, and an image plane that receives the light from the second means

Lerner, Scott A. (Livermore, CA); Bennett, Charles L. (Livermore, CA); Bixler, Jay V. (Oakland, CA); Kuzmenko, Paul J. (Livermore, CA); Lewis, Isabella T. (San Jose, CA)

2005-07-26T23:59:59.000Z

456

Microscopic analysis of irradiated AGR-1 coated particle fuel compacts  

SciTech Connect (OSTI)

The AGR-1 experiment involved irradiation of 72 TRISO-coated particle fuel compacts to a peak compact-average burnup of 19.5% FIMA with no in-pile failures observed out of 3 x 105 total particles. Irradiated AGR-1 fuel compacts have been cross-sectioned and analyzed with optical microscopy to characterize kernel, buffer, and coating behavior. Six compacts have been examined, spanning a range of irradiation conditions (burnup, fast fluence, and irradiation temperature) and including all four TRISO coating variations irradiated in the AGR-1 experiment. The cylindrical specimens were sectioned both transversely and longitudinally, then polished to expose from 36 to 79 individual particles near midplane on each mount. The analysis focused primarily on kernel swelling and porosity, buffer densification and fracturing, bufferIPyC debonding, and fractures in the IPyC and SiC layers. Characteristic morphologies have been identified, 981 particles have been classified, and spatial distributions of particle types have been mapped. No significant spatial patterns were discovered in these cross sections. However, some trends were found between morphological types and certain behavioral aspects. Buffer fractures were found in 23% of the particles, and these fractures often resulted in unconstrained kernel protrusion into the open cavities. Fractured buffers and buffers that stayed bonded to IPyC layers appear related to larger pore size in kernels. BufferIPyC interface integrity evidently factored into initiation of rare IPyC fractures. Fractures through part of the SiC layer were found in only four classified particles, all in conjunction with IPyCSiC debonding. Compiled results suggest that the deliberate coating fabrication variations influenced the frequencies of IPyC fractures and IPyCSiC debonds.

Scott A. Ploger; Paul A. Demkowicz; John D. Hunn; Jay S. Kehn

2014-05-01T23:59:59.000Z

457

On a -ideal of compact sets Tamas Matrai,a  

E-Print Network [OSTI]

subsets of 2 and prove that it is not Tukey reducible to the ideal I1/n = {H : hH 1/h , Tukey reducibility 2000 MSC: 03E15, 54H05, 28A05 1. Complexity of -ideals of compact sets Let X". The notion of complexity we are concerned with in the present note is Tukey reducibility, i.e. the comparison

Mátrai, Tamás

458

Flaw-detection characteristics of the compact MIB-4 betatron  

SciTech Connect (OSTI)

The compact pulse betatron using electrons accelerated to an energy of up to 4 MeV (MIB-4) is designed for the radiographic inspection of reinforced-concrete structures and buildings, welded joints, various materials, and assemblies. Information which refines and complements the method of inspecting parts by means of the MIB-4 device is provided. The results obtained in testing this equipment abroad are given.

Boiko, D.A.; Filimonov, A.A.; Chakhlov, V.L.

1987-09-01T23:59:59.000Z

459

Compact betatron with four controlling-field periodicity elements  

SciTech Connect (OSTI)

A compact 3-MeV betatron is described. The electromagnet of the betatron uses removable four-element poles, which form a magnetic field with azimuthal variation. The betatron accelerates 2 x 10/sup 10/ particles per cycle. The cycle repetition frequency is up to 400 Hz. The radius of the equilibrium orbit is 4.5 cm. The maximum interpole gap is 4 cm. The depth of magnetic-field variation on the equilibrium radius is 0.15.

Chakhlov, V.L.; Pushin, V.S.; Burov, G.I.; Zvontsov, A.A.; Zvorygin, V.P.; Zrelov, Yu.D.

1987-01-01T23:59:59.000Z

460

Stability of thin-shell interfaces inside compact stars  

E-Print Network [OSTI]

We use the thin-shell Darmois-Israel formalism to model and assess the stability of the interfaces separating phases, e.g. the core and the crust, within compact stars. We exemplify the relevance and non-triviality of this treatment in the simplest case of an incompressible star, in constant pressure phase transitions, and in the case of strange quark stars with crust.

Jonas P. Pereira; Jaziel G. Coelho; Jorge A. Rueda

2015-01-05T23:59:59.000Z

Note: This page contains sample records for the topic "incandescent compact fluorescent" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Ship response using a compact wave spectrum model  

E-Print Network [OSTI]

characterization of the sea. The next step in determining and evaluating the response characteristics of a design ship rests in the ability to relate the wave energy spectrum to actual ship responses. Through detailed research of the ocean and based upon laws... to spectral width and spectral shape is also studied. The original and compacted wave data bases are then used to excite sets of ship response amplitude operator's (RAO's). The resulting response spectra are examined both statistically and for any...

Linn, Larry Donald

1985-01-01T23:59:59.000Z

462

VALIDATION OF A THERMAL CONDUCTIVITY MEASUREMENT SYSTEM FOR FUEL COMPACTS  

SciTech Connect (OSTI)

A high temperature guarded-comparative-longitudinal heat flow measurement system has been built to measure the thermal conductivity of a composite nuclear fuel compact. It is a steady-state measurement device designed to operate over a temperature range of 300 K to 1200 K. No existing apparatus is currently available for obtaining the thermal conductivity of the composite fuel in a non-destructive manner due to the compacts unique geometry and composite nature. The current system design has been adapted from ASTM E 1225. As a way to simplify the design and operation of the system, it uses a unique radiative heat sink to conduct heat away from the sample column. A finite element analysis was performed on the measurement system to analyze the associated error for various operating conditions. Optimal operational conditions have been discovered through this analysis and results are presented. Several materials have been measured by the system and results are presented for stainless steel 304, inconel 625, and 99.95% pure iron covering a range of thermal conductivities of 10 W/m*K to 70 W/m*K. A comparison of the results has been made to data from existing literature.

Jeff Phillips; Colby Jensen; Changhu Xing; Heng Ban

2011-03-01T23:59:59.000Z

463

Tracer diffusion in compacted, water-saturated bentonite  

SciTech Connect (OSTI)

Compacted Na-bentonite clay barriers, widely used in theisolation of solid-waste landfills and other contaminated sites, havebeen proposed for a similar use in the disposal of high-level radioactivewaste. Molecular diffusion through the pore space in these barriers playsa key role in their performance, thus motivating recent measurements ofthe apparent diffusion coefficient tensor of water tracers in compacted,water-saturated Na-bentonites. In the present study, we introduce aconceptual model in which the pore space of water-saturated bentonite isdivided into 'macropore' and 'interlayer nanopore' compartments. Withthis model we determine quantitatively the relative contributions ofpore-network geometry (expressed as a geometric factor) and of thediffusive behavior of water molecules near montmorillonite basal surfaces(expressed as a contristivity factor) to the apparent diffusioncoefficient tensor. Our model predicts, in agreement with experiment,that the mean principal value of the apparent diffusion coefficienttensor follows a single relationship when plotted against the partialmontmorillonite dry density (mass of montmorillonite per combined volumeof montmorillonite and pore space). Using a single fitted parameter, themean principal geometric factor, our model successfully describes thisrelationship for a broad range of bentonite-water system, from dilute gelto highly-compacted bentonite with 80 percent of its pore water ininterlayer nanopores.

Bourg, Ian C.; Sposito, Garrison; Bourg, Alain C.M.

2005-08-04T23:59:59.000Z

464

Time machines with the compactly determined Cauchy horizon  

E-Print Network [OSTI]

The building of a time machine, if possible at all, requires the relevant regions of spacetime to be compact (that is, physically speaking, free from sources of unpredictability such as infinities and singularities). Motivated by this argument we consider the spacetimes with the compactly determined Cauchy horizons (CDCHs), the defining property of which is the compactness of $\\overline{J^-(\\EuScript U)}\\cap J^+(\\EuScript S_0)$, where $\\EuScript U$ is an open subset of the Cauchy horizon and $\\EuScript S_0$ is a Cauchy surface of the initial globally hyperbolic region $\\ingh$. The following two facts are established: 1) $\\ingh$ has no globally hyperbolic maximal extension. This means that by shaping appropriately a precompact portion of a globally hyperbolic region one can \\emph{force} the Universe to produce either a closed causal curve, or a quasiregular singularity, whichever it abhors less; 2) Before a CDCH is formed a null geodesic appears which infinitely approaches the horizon returning again and again in the same --- arbitrarily small --- region. The energy of the photon moving on such a geodesic increases with each passage, or at least falls insufficiently fast. As a result, an observer located in the mentioned region would see a bunch of photons passing through his laboratory with the arbitrarily large total energy. We speculate that this phenomenon may have observable consequences.

S. Krasnikov

2014-08-01T23:59:59.000Z

465

EXPLORING THE INTERSTELLAR MEDIA OF OPTICALLY COMPACT DWARF GALAXIES  

SciTech Connect (OSTI)

We present new Very Large Array H I spectral line, archival Sloan Digital Sky Survey, and archival Spitzer Space Telescope imaging of eight star-forming blue compact dwarf galaxies that were selected to be optically compact (optical radii <1 kpc). These systems have faint blue absolute magnitudes (M{sub B} {approx}> -17), ongoing star formation (based on emission-line selection by the H{alpha} or [O III] lines), and are nearby (mean velocity = 3315 km s{sup -1} {approx_equal} 45 Mpc). One galaxy in the sample, ADBS 113845+2008, is found to have an H I halo that extends 58 r-band scale lengths from its stellar body. In contrast, the rest of the sample galaxies have H I radii to optical-scale-length ratios ranging from 9.3 to 26. The size of the H I disk in the 'giant disk' dwarf galaxy ADBS 113845+2008 appears to be unusual as compared with similarly compact stellar populations.

Most, Hans P.; Cannon, John M.; Engstrom, Eric; Fliss, Palmer [Department of Physics and Astronomy, Macalester College, 1600 Grand Avenue, Saint Paul, MN 55105 (United States); Salzer, John J. [Department of Astronomy, Indiana University, 727 East Third Street, Bloomington, IN 47405 (United States); Rosenberg, Jessica L., E-mail: hmost@macalester.edu, E-mail: jcannon@macalester.edu, E-mail: slaz@astro.indiana.edu, E-mail: jrosenb4@gmu.edu [School of Physics, Astronomy, and Computational Science, George Mason University, Fairfax, VA 22030 (United States)

2013-06-15T23:59:59.000Z

466

Ultra-Compact High-Efficiency Luminaire for General Illumination  

SciTech Connect (OSTI)

Cree has developed a new ultra-compact light emitting diode (LED) luminaire capable of providing high efficacy with excellent color quality that can lead to significant energy savings in today??s commercial and retail applications. This success was based on an integrated development effort tailoring the LED component characteristics, optics, thermal management and driver design for the small footprint to achieve an overall system efficiency of ? 70%. A new LED component was designed to provide high brightness and efficacy in a form factor that allowed for a small directional beam with a luminaire housing design able to dissipate the heat effectively using a small physical envelope. A very compact, 90% efficient driver was developed to meet the system performance while not taking away any thermal mass from the heat sink. A 91% efficient secondary optics was designed to maximize efficiency while providing a smooth beam. The reliability of the new LED component was robust under accelerated testing conditions. Luminaires were assembled integrating the novel LED component, secondary optics, heat sink and driver technology to demonstrate the system improvement. Cree has successfully completed this project by developing an ultra-compact LED luminaire that provided 380 lumens at a correlated color temperature (CCT) of 2822 K and color rendering index (CRI) of 94 with an efficacy of 94 lumens per watt (LPW) when operating at 4 W input power (steady state) with an overall system efficiency of 81%. At a higher input power of 9 Watts, the lamp provided 658 lumens at 71 LPW.

Ted Lowes

2012-04-08T23:59:59.000Z

467

X-Ray Fluorescence (XRF) Analysis of Obsidian Artifacts from Shoofly Ruin, Central Arizona  

E-Print Network [OSTI]

X-RAY FLUORESCENCE (XRF) ANALYSIS OF OBSIDIAN ARTIFACTS FROM62:426-437. SOUTHWEST XRF PAPER Table 1. X-ray fluorescence

Shackley, M. Steven

1986-01-01T23:59:59.000Z

468

A Red Cy3-Based Biarsenical Fluorescent Probe Targeted to a Complement...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Red Cy3-Based Biarsenical Fluorescent Probe Targeted to a Complementary Binding Peptide. A Red Cy3-Based Biarsenical Fluorescent Probe Targeted to a Complementary Binding Peptide....

469

E-Print Network 3.0 - angle fluorescence interference Sample...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

both the excitation and fluorescence detection bands of WIBS. Interference filters were avoided... A low-cost multi-channel aerosol fluorescence sensor for networked deployment...

470

E-Print Network 3.0 - albumin fluorescence study Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

of tryptophan fluorescence decay in proteins using a subnanosecond 295 nm light-emitting diode Summary: . Fluorescence decay and anisotropy decay measurements of human serum...

471

E-Print Network 3.0 - activated delayed fluorescence Sample Search...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

69 Rapid Communication Fluorescence Resonance Energy Transfer Analysis of Summary: Rapid Communication Fluorescence Resonance Energy Transfer Analysis of Cell Surface Receptor......

472

Fluorescent lamp unit with magnetic field generating means  

DOE Patents [OSTI]

A fluorescent lamp unit having a magnetic field generating means for improving the performance of the fluorescent lamp is disclosed. In a preferred embodiment the fluorescent lamp comprises four longitudinally extending leg portions disposed in substantially quadrangular columnar array and joined by three generally U-shaped portions disposed in different planes. In another embodiment of the invention the magnetic field generating means comprises a plurality of permanent magnets secured together to form a single columnar structure disposed within a centrally located region defined by the shape of lamp envelope. 4 figs.

Grossman, M.W.; George, W.A.

1989-08-08T23:59:59.000Z

473

THE HISTORY AND TECHNICAL EVOLUTION OF HIGH FREQUENCY FLUORESCENT LIGHTING  

E-Print Network [OSTI]

Dec. 1953. "Hi-Volt-Cycle Lighting ~ Launched i n a Hi-Wide2, F e b r u a r y , 19 53. "Lighting Your Plant with Highg h Frequency Fluorescent Lighting John H. Campbell December

Campbell, John H.

2011-01-01T23:59:59.000Z

474

REDUCING INCIDENTAL FLUORESCENCE IN LIVE CELL IMAGING A. Altinok 1  

E-Print Network [OSTI]

, the technique is based on staining bio molecules selectively with proteins carrying fluorescence dyes of known. For instance, length measurements in Fig.1 would lack accuracy since the ends of the objects are blurry within

California at Santa Barbara, University of

475

LIGHT-INDUCED CHANGES IN THE FLUORESCENCE YIELD OF  

E-Print Network [OSTI]

a in system II, the system which sensitizes the oxygen-evolving reaction (7-14). The factor controlling fluorescence intensity is the redox state of Q, the electron acceptor in the system It reaction center (9). Fig

Govindjee

476

Calibration of fluorescence resonance energy transfer in microscopy  

DOE Patents [OSTI]

Imaging hardware, software, calibrants, and methods are provided to visualize and quantitate the amount of Fluorescence Resonance Energy Transfer (FRET) occurring between donor and acceptor molecules in epifluorescence microscopy. The MicroFRET system compensates for overlap among donor, acceptor, and FRET spectra using well characterized fluorescent beads as standards in conjunction with radiometrically calibrated image processing techniques. The MicroFRET system also provides precisely machined epifluorescence cubes to maintain proper image registration as the sample is illuminated at the donor and acceptor excitation wavelengths. Algorithms are described that pseudocolor the image to display pixels exhibiting radiometrically-corrected fluorescence emission from the donor (blue), the acceptor (green) and FRET (red). The method is demonstrated on samples exhibiting FRET between genetically engineered derivatives of the Green Fluorescent Protein (GFP) bound to the surface of Ni chelating beads by histidine-tags.

Youvan, Dougalas C.; Silva, Christopher M.; Bylina, Edward J.; Coleman, William J.; Dilworth, Michael R.; Yang, Mary M.

2003-12-09T23:59:59.000Z

477

Exploring the mechanome with optical tweezers and single molecule fluorescence  

E-Print Network [OSTI]

The combination of optical tweezers and single molecule fluorescence into an instrument capable of making combined, coincident measurements adds an observable dimension that allows for the examination of the localized ...

Brau, Ricardo R. (Ricardo Rafael), 1979-

2008-01-01T23:59:59.000Z

478

Protein subcellular localization assays using split fluorescent proteins  

DOE Patents [OSTI]

The invention provides protein subcellular localization assays using split fluorescent protein systems. The assays are conducted in living cells, do not require fixation and washing steps inherent in existing immunostaining and related techniques, and permit rapid, non-invasive, direct visualization of protein localization in living cells. The split fluorescent protein systems used in the practice of the invention generally comprise two or more self-complementing fragments of a fluorescent protein, such as GFP, wherein one or more of the fragments correspond to one or more beta-strand microdomains and are used to "tag" proteins of interest, and a complementary "assay" fragment of the fluorescent protein. Either or both of the fragments may be functionalized with a subcellular targeting sequence enabling it to be expressed in or directed to a particular subcellular compartment (i.e., the nucleus).

Waldo, Geoffrey S. (Santa Fe, NM); Cabantous, Stephanie (Los Alamos, NM)

2009-09-08T23:59:59.000Z

479

Calibration of fluorescence resonance energy transfer in microscopy  

DOE Patents [OSTI]

Imaging hardware, software, calibrants, and methods are provided to visualize and quantitate the amount of Fluorescence Resonance Energy Transfer (FRET) occurring between donor and acceptor molecules in epifluorescence microscopy. The MicroFRET system compensates for overlap among donor, acceptor, and FRET spectra using well characterized fluorescent beads as standards in conjunction with radiometrically calibrated image processing techniques. The MicroFRET system also provides precisely machined epifluorescence cubes to maintain proper image registration as the sample is illuminated at the donor and acceptor excitation wavelengths. Algorithms are described that pseudocolor the image to display pixels exhibiting radiometrically-corrected fluorescence emission from the donor (blue), the acceptor (green) and FRET (red). The method is demonstrated on samples exhibiting FRET between genetically engineered derivatives of the Green Fluorescent Protein (GFP) bound to the surface of Ni chelating beads by histidine-tags.

Youvan, Douglas C. (San Jose, CA); Silva, Christopher M. (Sunnyvale, CA); Bylina, Edward J. (San Jose, CA); Coleman, William J. (Moutain View, CA); Dilworth, Michael R. (Santa Cruz, CA); Yang, Mary M. (San Jose, CA)

2002-09-24T23:59:59.000Z

480

Preliminary results of post-irradiation examination of the AGR-1 TRISO fuel compacts  

SciTech Connect (OSTI)

Five irradiated fuel compacts from the AGR-1 experiment have been examined in detail in order to assess in-pile fission product release behavior. Compacts were electrolytically deconsolidated and analyzed using the leach-burn-leach technique to measure fission product inventory in the compact matrix and identify any particles with a defective SiC layer. Loose particles were then gamma counted to measure the fission product inventory. One particle with a defective SiC layer was found in the five compacts examined. The fractional release of Ag 110m from the particles was significant. The total fraction of silver released from all the particles within a compact ranged from 0-0.63 and individual particles within a single compact often exhibited a very wide range of silver release. The average fractional release of Eu-154 from all particles in a compact was 2.410-41.310-2, which is indicative of release through intact coatings. The fractional Cs-134 inventory in the compact matrix was <210-5 when all coatings remained intact, indicating good cesium retention. Approximately 1% of the palladium inventory was found in the compact matrix for two of the compacts, indicating significant release through intact coatings.

Paul Demkowicz; John Hunn; Robert Morris; Jason Harp; Philip Winston; Charles Baldwin; Fred Montgomery; Scott Ploger; Isabella van Rooyen

2012-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "incandescent compact fluorescent" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Rapid identification of bacteria using an umbelliferone fluorescent assay  

E-Print Network [OSTI]

RAPID IDENTIFICATION OF BACTERIA USING AN UMBELLIFERONE FLUORESCENT ASSAY A Thesis by RICHARD THOMAS CHAMBLIN, JR, Submitted to the Graduate College of' Texas A&M University in partial fulfillment of the requirement for the degree of MASTER... OF SCIENCE August 1983 Major Subject: Veterinary Microbiology RAPID IDENTIFICATION OF BACTERIA USING AN UMBELLIFERONE FLUORESCENT ASSAY A Thesis by RICHARD THOMAS CHAMBLIN, JR ~ Approved as to style and content by ( -Chairman of Committee) John M...

Chamblin, Richard Thomas

1983-01-01T23:59:59.000Z

482

Development of laser excited atomic fluorescence and ionization methods  

SciTech Connect (OSTI)

Progress report: May 1, 1988 to December 31, 1991. The research supported by DE-FG05-88ER13881 during the past (nearly) 3 years can be divided into the following four categories: (1) theoretical considerations of the ultimate detection powers of laser fluorescence and laser ionization methods; (2) experimental evaluation of laser excited atomic fluorescence; (3) fundamental studies of atomic and molecular parameters in flames and plasmas; (4) other studies.

Winefordner, J.D.

1991-01-01T23:59:59.000Z

483

Microscopic analysis of irradiated AGR-1 coated particle fuel compacts  

SciTech Connect (OSTI)

The AGR-1 experiment involved irradiation of 72 TRISO-coated particle fuel compacts to a peak burnup of 19.5% FIMA with no in-pile failures observed out of 3105 total particles. Irradiated AGR-1 fuel compacts have been cross-sectioned and analyzed with optical microscopy to characterize kernel, buffer, and coating behavior. Five compacts have been examined so far, spanning a range of irradiation conditions (burnup, fast fluence, and irradiation temperature) and including all four TRISO coating variations irradiated in the AGR-1 experiment. The cylindrical specimens were sectioned both transversely and longitudinally, then polished to expose between approximately 40-80 individual particles on each mount. The analysis focused primarily on kernel swelling and porosity, buffer densification and fracturing, buffer-IPyC debonding, and fractures in the IPyC and SiC layers. Characteristic morphologies have been identified, over 800 particles have been classified, and spatial distributions of particle types have been mapped. No significant spatial patterns were discovered in these cross sections. However, some trends were found between morphological types and certain behavioral aspects. Buffer fractures were found in approximately 23% of the particles, and these fractures often resulted in unconstrained kernel swelling into the open cavities. Fractured buffers and buffers that stayed bonded to IPyC layers appear related to larger pore size in kernels. Buffer-IPyC interface integrity evidently factored into initiation of rare IPyC fractures. Fractures through part of the SiC layer were found in only three particles, all in conjunction with IPyC-SiC debonding. Compiled results suggest that the deliberate coating fabrication variations influenced the frequencies of IPyC fractures, IPyC-SiC debonds, and SiC fractures.

Scott Ploger; Paul Demkowicz; John Hunn; Robert Morris

2012-10-01T23:59:59.000Z

484

COMPACT BINARY PROGENITORS OF SHORT GAMMA-RAY BURSTS  

SciTech Connect (OSTI)

In recent years, detailed observations and accurate numerical simulations have provided support to the idea that mergers of compact binaries containing either two neutron stars (NSs) or an NS and a black hole (BH) may constitute the central engine of short gamma-ray bursts (SGRBs). The merger of such compact binaries is expected to lead to the production of a spinning BH surrounded by an accreting torus. Several mechanisms can extract energy from this system and power the SGRBs. Here we connect observations and numerical simulations of compact binary mergers, and use the current sample of SGRBs with measured energies to constrain the mass of their powering tori. By comparing the masses of the tori with the results of fully general-relativistic simulations, we are able to infer the properties of the binary progenitors that yield SGRBs. By assuming a constant efficiency in converting torus mass into jet energy, {epsilon}{sub jet} = 10%, we find that most of the tori have masses smaller than 0.01 M{sub Sun }, favoring 'high-mass' binary NSs mergers, i.e., binaries with total masses {approx}> 1.5 the maximum mass of an isolated NS. This has important consequences for the gravitational wave signals that may be detected in association with SGRBs, since 'high-mass' systems do not form a long-lived hypermassive NS after the merger. While NS-BH systems cannot be excluded to be the engine of at least some of the SGRBs, the BH would need to have an initial spin of {approx}0.9 or higher.

Giacomazzo, Bruno [JILA, University of Colorado and National Institute of Standards and Technology, Boulder, CO 80309 (United States); Perna, Rosalba [JILA and Department of Astrophysical and Planetary Sciences, University of Colorado, Boulder, CO 80309 (United States); Rezzolla, Luciano [Max-Planck-Institut fuer Gravitationsphysik, Albert-Einstein-Institut, Potsdam D-14476 (Germany); Troja, Eleonora [NASA Goddard Space Flight Center, Greenbelt, MD 20771 (United States); Lazzati, Davide [Department of Physics, NC State University, 2401 Stinson Drive, Raleigh, NC 27695-8202 (United States)

2013-01-10T23:59:59.000Z

485

Controlled powder morphology experiments in megabar 304 stainless steel compaction  

SciTech Connect (OSTI)

Experiments with controlled morphology including shape, size, and size distribution were made on 304L stainless steel powders. These experiments involved not only the powder variables but pressure variables of 0.08 to 1.0 Mbar. Also included are measured container strain on the material ranging from 1.5% to 26%. Using a new strain controllable design it was possible to seperate and control, independently, strain and pressure. Results indicate that powder morphology, size distribution, packing density are among the pertinent parameters in predicting compaction of these powders.

Staudhammer, K.P.; Johnson, K.A.

1985-01-01T23:59:59.000Z

486

PDC (polycrystalline diamond compact) bit research at Sandia National Laboratories  

SciTech Connect (OSTI)

From the beginning of the geothermal development program, Sandia has performed and supported research into polycrystalline diamond compact (PDC) bits. These bits are attractive because they are intrinsically efficient in their cutting action (shearing, rather than crushing) and they have no moving parts (eliminating the problems of high-temperature lubricants, bearings, and seals.) This report is a summary description of the analytical and experimental work done by Sandia and our contractors. It describes analysis and laboratory tests of individual cutters and complete bits, as well as full-scale field tests of prototype and commercial bits. The report includes a bibliography of documents giving more detailed information on these topics. 26 refs.

Finger, J.T.; Glowka, D.A.

1989-06-01T23:59:59.000Z

487

Diffusion Welding of Compact Heat Exchangers for Nuclear Applications  

SciTech Connect (OSTI)

The next--generation nuclear plant (NGNP) is designed to be a flexible source of energy, producing various mixes of electrical energy and process heat (for example, for hydrogen generation) on demand. Compact heat exchangers provide an attractive way to move energy from the helium primary reactor coolant to process heat uses. For process heat efficiency, reactor outlet temperatures of 750--900C are desirable. There are minor but deleterious components in the primary coolant; the number of alloys that can handle this environment is small. The present work concentrates on Alloys 800H and 617.

Denis Clark; Ron Mizia; Dr. Michael V. Glazoff; Mr. Michael W. Patterson

2012-06-01T23:59:59.000Z

488

Compact cyclone filter train for radiological and hazardous environments  

DOE Patents [OSTI]

A compact cyclone filter train for the removal of hazardous and radiologi particles from a gaseous fluid medium which permits a small cyclone separator to be used in a very small space envelope due to the arrangement of the filter housing adjacent to the separator with the cyclone separator and the filters mounted on a plate. The entire unit will have a hoist connection at the center of gravity so that the entire unit including the separator, the filters, and the base can be lifted and repositioned as desired.

Bench, Thomas R. (Pittsburgh, PA)

1998-01-01T23:59:59.000Z

489

Compact cyclone filter train for radiological and hazardous environments  

DOE Patents [OSTI]

A compact cyclone filter train is disclosed for the removal of hazardous and radiological particles from a gaseous fluid medium. This filter train permits a small cyclone separator to be used in a very small space envelope due to the arrangement of the filter housing adjacent to the separator with the cyclone separator and the filters mounted on a plate. The entire unit will have a hoist connection at the center of gravity so that the entire unit including the separator, the filters, and the base can be lifted and repositioned as desired. 3 figs.

Bench, T.R.

1998-04-28T23:59:59.000Z

490

Compact high resolution isobar separator for study of exotic decays  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE:1 First Use of Energy for All Purposes (Fuel and Nonfuel),Feet) Year Jan Feb Mar Apr MayAtmospheric Optical Depth7-1D: Vegetation Proposed New SubstationCleanCommunity Involvement and Making aCompact soft

491

A light diet for a giant appetite: An assessment of China's proposed fluorescent lamp standard  

E-Print Network [OSTI]

standard for linear fluorescent lamps Length (mm) Minimum efficacy (lm/W) Efficacy for energy conservation

Lin, Jiang

2002-01-01T23:59:59.000Z

492

Application of fluorescence microscopy to coal-derived resid characterization  

SciTech Connect (OSTI)

This study evaluates the usefulness of a fluorescence microscopy methodology to analyze coal-derived resids and interpret the data in the light of liquefaction processing conditions, process response, the inferred resid reactivity, and in relation to results of other analytical data. The fluorescence technique utilized has been widely applied to coal and kerogen characterization, albeit with some modifications, but is novel in its application to the characterization of coal liquids. Fluorescence is the emission of light energy which occurs when electrons, having been excited to a higher energy orbital, return to their lower energy ground state. The majority of organic molecules that fluoresce are those with conjugated double bonds (chromophores), such as aromatics, characterized by pi-electrons less strongly bound within the molecule than sigma electrons, that can be excited to anti-bonding pi-orbitals. Increasing the extent of pi-bond conjugation (i.e. larger molecular size) generally imparts a shift in absorption and emission spectra to longer wavelengths. Resid fluorescence largely depends on the concentration and degree of conjugation of aromatic chromophores in the high molecular weight liquids, possibly with ancillary effects from oxygen functionalities. In this context, fluorescence analysis of liquefaction resids can potentially evaluate process performance, since direct liquefaction processes endeavor to break down the macromolecular structure of coal, and reduce the molecular weight of polycondensed aromatics through hydrogenation, the opening of ring structures, and heteroatom removal.

Rathbone, R.F.; Hower, J.C.; Derbyshire, F.J.

1991-01-01T23:59:59.000Z

493

Application of fluorescence microscopy to coal-derived resid characterization  

SciTech Connect (OSTI)

This study evaluates the usefulness of a fluorescence microscopy methodology to analyze coal-derived resids and interpret the data in the light of liquefaction processing conditions, process response, the inferred resid reactivity, and in relation to results of other analytical data. The fluorescence technique utilized has been widely applied to coal and kerogen characterization, albeit with some modifications, but is novel in its application to the characterization of coal liquids. Fluorescence is the emission of light energy which occurs when electrons, having been excited to a higher energy orbital, return to their lower energy ground state. The majority of organic molecules that fluoresce are those with conjugated double bonds (chromophores), such as aromatics, characterized by pi-electrons less strongly bound within the molecule than sigma electrons, that can be excited to anti-bonding pi-orbitals. Increasing the extent of pi-bond conjugation (i.e. larger molecular size) generally imparts a shift in absorption and emission spectra to longer wavelengths. Resid fluorescence largely depends on the concentration and degree of conjugation of aromatic chromophores in the high molecular weight liquids, possibly with ancillary effects from oxygen functionalities. In this context, fluorescence analysis of liquefaction resids can potentially evaluate process performance, since direct liquefaction processes endeavor to break down the macromolecular structure of coal, and reduce the molecular weight of polycondensed aromatics through hydrogenation, the opening of ring structures, and heteroatom removal.

Rathbone, R.F.; Hower, J.C.; Derbyshire, F.J.

1991-12-31T23:59:59.000Z

494

FINAL PROJECT REPORT LOAD MODELING TRANSMISSION RESEARCH  

E-Print Network [OSTI]

to be the compact fluorescent bulbs (CFBs) that the engineerbulbs with compact fluorescent bulbs (CFBs) continues to

Lesieutre, Bernard

2013-01-01T23:59:59.000Z

495

Catalog of DC Appliances and Power Systems  

E-Print Network [OSTI]

loss for the compact fluorescent bulb replacement. For mosta light bulb or tube, a compact fluorescent lamp typically

Garbesi, Karina

2012-01-01T23:59:59.000Z

496

Development of rapid microbial methods for lysine quantification in feed ingredients based on green fluorescent protein fluorescence  

E-Print Network [OSTI]

fulfillment of the requirements for the degree of DOCTOR OF PHILOSOPHY Approved by: Chair of Committee, Steven C. Ricke Committee Members, Deborah Siegele Jean Gould Dorothy Shippen Chair of Molecular... on Green Fluorescent Protein Fluorescence. (December 2005) Vesela I. Chalova-Zhekova, Diplom., Higher Institute of Food and Flavor Industries Chair of Advisory Committee: Dr. Steven Ricke Lysine is one of the more limiting amino acids in protein...

Chalova-Zhekova, Vesela I.

2007-04-25T23:59:59.000Z

497

Design and implementation of a solar power system in rural Haiti  

E-Print Network [OSTI]

This paper describes the design and implementation of a solar power system for a school and health center in Petit-Anse, Haiti. The end-use applications are lighting via a set of fluorescent and incandescent bulbs, and a ...

Hussam, Shaheer M. (Shaheer Muqtasid), 1981-

2004-01-01T23:59:59.000Z

498

Plant Physiol. (1983) 73, 4504510 0032-0889/83/73/0450/02/$00.50/0  

E-Print Network [OSTI]

wrapped around 20-w cool white fluorescent tubes. For far-red light (730 nm peak, 15 nm half band width-w incandescent bulb was filtered through No. 2025 Plexiglas (Rohm and Hass, Inc.). Irradiance levels

Decoteau, Dennis R.

499

Commercialization of gallium nitride nanorod arrays on silicon for solid-state lighting  

E-Print Network [OSTI]

One important component in energy usage is lighting, which is currently dominated by incandescent and fluorescent lamps. However, due to potentially higher efficiencies and thus higher energy savings, solid-state lighting ...

Wee, Qixun

2008-01-01T23:59:59.000Z

500

2 Masers and Lasers January 31, 2008  

E-Print Network [OSTI]

, a candle, an incandescent bulb, or a fluorescent source, is the result of incoherent emission of light from of Radiation) that extended the existence of coherent sources right into the ultraviolet spectrum

Thouless, David