Sample records for imported low-sulfur light

  1. LOW SULFUR HOME HEATING OIL DEMONSTRATION PROJECT SUMMARY REPORT.

    SciTech Connect (OSTI)

    BATEY, J.E.; MCDONALD, R.J.

    2005-06-01T23:59:59.000Z

    This project was funded by NYSERDA and has clearly demonstrated many advantages of using low sulfur content heating oil to provide thermal comfort in homes. Prior laboratory research in the United States and Canada had indicated a number of potential benefits of using lower sulfur (0.05%) heating oil. However, this prior research has not resulted in the widespread use of low sulfur fuel oil in the marketplace. The research project described in this report was conducted with the assistance of a well-established fuel oil marketer in New York State (NYS) and has provided clear proof of the many real-world advantages of marketing and using low sulfur content No. 2 fuel oil. The very positive experience of the participating marketer over the past three years has already helped to establish low sulfur heating oil as a viable option for many other fuel marketers. In large part, based on the initial findings of this project and the experience of the participating NYS oilheat marketer, the National Oilheat Research Alliance (NORA) has already fully supported a resolution calling for the voluntary use of low sulfur (0.05 percent) home heating oil nationwide. The NORA resolution has the goal of converting eighty percent of all oil-heated homes to the lower sulfur fuel (0.05 percent by weight) by the year 2007. The Oilheat Manufacturers Association (OMA) has also passed a resolution fully supporting the use of lower sulfur home heating oil in the equipment they manufacture. These are important endorsements by prominent national oil heat associations. Using lower sulfur heating oil substantially lowers boiler and furnace fouling rates. Laboratory studies had indicated an almost linear relationship between sulfur content in the oil and fouling rates. The completed NYSERDA project has verified past laboratory studies in over 1,000 occupied residential homes over the course of three heating seasons. In fact, the reduction in fouling rates so clearly demonstrated by this project is almost the same as predicted by past laboratory studies. Fouling deposition rates are reduced by a factor of two to three by using lower sulfur oil. This translates to a potential for substantial service cost savings by extending the interval between labor-intensive cleanings of the internal surfaces of the heating systems in these homes. In addition, the time required for annual service calls can be lowered, reducing service costs and customer inconvenience. The analyses conducted as part of this field demonstration project indicates that service costs can be reduced by up to $200 million a year nationwide by using lower sulfur oil and extending vacuum cleaning intervals depending on the labor costs and existing cleaning intervals. The ratio of cost savings to added fuel costs is economically attractive based on past fuel price differentials for the lower sulfur product. The ratio of cost savings to added costs vary widely as a function of hourly service rates and the additional cost for lower sulfur oil. For typical values, the expected benefit is a factor of two to four higher than the added fuel cost. This means that for every dollar spent on higher fuel cost, two to four dollars can be saved by lowered vacuum cleaning costs when the cleaning intervals are extended. Information contained in this report can be used by individual oil marketers to estimate the benefit to cost ratio for their specific applications. Sulfur oxide and nitrogen oxide air emissions are reduced substantially by using lower sulfur fuel oil in homes. Sulfur oxides emissions are lowered by 75 percent by switching from fuel 0.20 percent to 0.05 percent sulfur oil. This is a reduction of 63,000 tons a year nationwide. In New York State, sulfur oxide emissions are reduced by 13,000 tons a year. This translates to a total value of $12 million a year in Sulfur Oxide Emission Reduction Credits for an emission credit cost of $195 a ton. While this ''environmental cost'' dollar savings is smaller than the potential service costs reduction, it is very significant. It represents an important red

  2. Fuel switch could bring big savings for HECO Liquefied natural gas beats low-sulfur oil in cost and equipment

    E-Print Network [OSTI]

    by switching to LNG instead of continuing to burn low-sulfur fuel oil and installing new emission controls that stands to benefit if regulators approve LNG shipments to the state. "Beyond payment for this study, FGE will receive no compensation whatsoever whether the state decides to import LNG or not, and no matter under

  3. Sibley station low-sulfur coal conversion program

    SciTech Connect (OSTI)

    Rupinskas, R.L. [Sargent & Lundy LLC, Chicago, IL (United States); Rembold, D.F. [Missouri Public Service, Kansas City, MO (United States)

    1995-03-01T23:59:59.000Z

    After embarking on an upgrade project in 1986 that was designed to allow efficient and reliable operation of its coal-fired Sibley station through 2010, Missouri Public Service (MPS) faced the uncertainty of impending acid-rain legislation. To protect its investment in the Sibley Rebuild Program, the utility evaluated compliance options based on the emerging legislation and concluded that switching to low-sulfur coal offered the least-cost compliance approach. Compared to installing a scrubber, switching to a low-sulfur coal was also more straightforward, although not without challenges and complications. This paper reviews the Sibley low-sulfur coal conversion program. At Sibley, fuel switching was chosen only after numerous internal and external studies; it withstood late challenges from natural gas and allowance trading. Switching demanded additional equipment to blend Power River Basin coals and other coals, and demanded additional and upgraded protective equipment in the areas of fire protection, dust collection, and explosion prevention. In the year since the coal conversion project was completed the facility has operated reliably, the economic benefits of the lower cost Powder River Basin coals have been realized, and the station has also met the requirements of both phases of the acid rain legislation. Fuel switching at Sibley required a team approach and careful analysis. The coal conversion project also required attention and dedication by team members in order to minimize fuel costs while maintaining optimum plant efficiency and availability.

  4. Ultra-Low Sulfur diesel Update & Future Light Duty Diesel

    Broader source: Energy.gov (indexed) [DOE]

    MARATHON PETROLEUM COMPANY LLC PARENT-MARATHON OIL COMPANY FIFTH LARGEST US REFINERY (OVER 1 MILLION BBLS OF CRUDE CAPACITY) MAJOR MARKETS IN MIDWEST AND SOUTHEAST ...

  5. Full Useful Life (120,000 miles) Exhaust Emission Performance of a NOx Adsorber and Diesel Particle Filter Equipped Passenger Car and Medium-duty Engine in Conjunction with Ultra Low Sulfur Fuel (Presentation)

    SciTech Connect (OSTI)

    Thornton, M.; Tatur, M.; Tomazic, D.; Weber, P.; Webb, C.

    2005-08-25T23:59:59.000Z

    Discusses the full useful life exhaust emission performance of a NOx (nitrogen oxides) adsorber and diesel particle filter equipped light-duty and medium-duty engine using ultra low sulfur diesel fuel.

  6. Characterization of fly ash from low-sulfur and high-sulfur coal sources: Partitioning of carbon and trace elements with particle size

    SciTech Connect (OSTI)

    Hower, J.C.; Trimble, A.S. [Univ. of Kentucky, Lexington, KY (United States). Center for Applied Energy Research]|[Franklin County High School, Frankfort, KY (United States); Eble, C.F. [Kentucky Geological survey, Lexington, KY (United States); Palmer, C.A.; Kolker, A. [Geological Survey, Reston, VA (United States)

    1999-07-01T23:59:59.000Z

    Fly ash samples were collected in November and December of 1994, from generating units at a Kentucky power station using high- and low-sulfur feed coals. The samples are part of a two-year study of the coal and coal combustion byproducts from the power station. The ashes were wet screened at 100, 200, 325, and 500 mesh (150, 75, 42, and 25 {micro}m, respectively). The size fractions were then dried, weighed, split for petrographic and chemical analysis, and analyzed for ash yield and carbon content. The low-sulfur heavy side and light side ashes each have a similar size distribution in the November samples. In contrast, the December fly ashes showed the trend observed in later months, the light-side ash being finer (over 20% more ash in the {minus}500 mesh [{minus}25 {micro}m] fraction) than the heavy-side ash. Carbon tended to be concentrated in the coarse fractions in the December samples. The dominance of the {minus}325 mesh ({minus}42 {micro}m) fractions in the overall size analysis implies, though, that carbon in the fine sizes may be an important consideration in the utilization of the fly ash. Element partitioning follows several patterns. Volatile elements, such as Zn and As, are enriched in the finer sizes, particularly in fly ashes collected at cooler, light-side electrostatic precipitator (ESP) temperatures. The latter trend is a function of precipitation at the cooler-ESP temperatures and of increasing concentration with the increased surface area of the finest fraction. Mercury concentrations are higher in high-carbon fly ashes, suggesting Hg adsorption on the fly ash carbon. Ni and Cr are associated, in part, with the spinel minerals in the fly ash.

  7. Cost-benefit analysis of ultra-low sulfur jet fuel

    E-Print Network [OSTI]

    Kuhn, Stephen (Stephen Richard)

    2010-01-01T23:59:59.000Z

    The growth of aviation has spurred increased study of its environmental impacts and the possible mitigation thereof. One emissions reduction option is the introduction of an Ultra Low Sulfur (ULS) jet fuel standard for ...

  8. Process for producing low-sulfur boiler fuel by hydrotreatment of solvent deashed SRC

    DOE Patents [OSTI]

    Roberts, George W. (Emmaus, PA); Tao, John C. (Perkiomenville, PA)

    1985-01-01T23:59:59.000Z

    In this invention, a process is disclosed characterized by heating a slurry of coal in the presence of a process-derived recycle solvent and passing same to a dissolver zone, separating the resultant gases and liquid/solid products therefrom, vacuum distilling the liquid/solids products, separating the portions of the liquid/solids vacuum distillation effluent into a solid ash, unconverted coal particles and SRC material having a boiling point above 850.degree. F. and subjecting same to a critical solvent deashing step to provide an ash-free SRC product. The lighter liquid products from the vacuum distillation possess a boiling point below 850.degree. F. and are passed through a distillation tower, from which recycled solvent is recovered in addition to light distillate boiling below 400.degree. F. (overhead). The ash-free SRC product in accompanyment with at least a portion of the process derived solvent is passed in combination to a hydrotreating zone containing a hydrogenation catalyst and in the presence of hydrogen is hydroprocessed to produce a desulfurized and denitrogenized low-sulfur, low-ash boiler fuel and a process derived recycle solvent which is recycled to slurry the coal in the beginning of the process before heating.

  9. Petrography and chemistry of sized fly ash from low-sulfur and high-sulfur coal sources

    SciTech Connect (OSTI)

    Hower, J.C. [Univ. of Kentucky, Lexington, KY (United States). Center for Applied Energy Research; Trimble, A.S. [Franklin County High School, Frankfort, KY (United States); Eble, C.F. [Kentucky Geological Survey, Lexington, KY (United States); Palmer, C. [Geological Survey, Reston, VA (United States)

    1996-12-31T23:59:59.000Z

    Fly ash samples were collected in November and December, 1994, from two units representing high- and low-sulfur feed coals at a Kentucky power station. The ashes were wet screened at 100, 200, 325, and 500 mesh. The dried ({approximately}40 C) fractions were then weighed, split for petrographic and chemical analysis, mounted in epoxy and prepared as polished pellets, and analyzed for ash yield and carbon content. The November ashes had a similar size distribution in the +325 mesh fractions. The low-sulfur hot side and cool side ashes had a similar size distribution in the November ashes. In contrast, the December fly ashes showed the typical trend, the cool-side ash being finer (over 20% more ash in the {minus}500 mesh fraction) than the hot-side ash. Carbon tends to be relatively concentrated in the coarse fractions. The dominance of the {minus}325 mesh fractions in the overall size analysis implies, though, that carbon in the fine sizes is an important consideration in the utilization potential of the fly ash.

  10. Tribological behavior of near-frictionless carbon coatings in high- and low-sulfur diesel fuels.

    SciTech Connect (OSTI)

    Alzoubi, M. F.; Ajayi, O. O.; Eryilmaz, O. L.; Ozturk, O.; Erdemir, A.; Fenske, G.

    2000-01-19T23:59:59.000Z

    The sulfur content in diesel fuel has a significant effect on diesel engine emissions, which are currently subject to environmental regulations. It has been observed that engine particulate and gaseous emissions are directly proportional to fuel sulfur content. With the introduction of low-sulfur fuels, significant reductions in emissions are expected. The process of sulfur reduction in petroleum-based diesel fuels also reduces the lubricity of the fuel, resulting in premature failure of fuel injectors. Thus, another means of preventing injector failures is needed for engines operating with low-sulfur diesel fuels. In this study, the authors evaluated a near-frictionless carbon (NFC) coating (developed at Argonne National Laboratory) as a possible solution to the problems associated with fuel injector failures in low-lubricity fuels. Tribological tests were conducted with NFC-coated and uncoated H13 and 52100 steels lubricated with high- and low- sulfur diesel fuels in a high-frequency reciprocating test machine. The test results showed that the NFC coatings reduced wear rates by a factor of 10 over those of uncoated steel surfaces. In low-sulfur diesel fuel, the reduction in wear rate was even greater (i.e., by a factor of 12 compared to that of uncoated test pairs), indicating that the NFC coating holds promise as a potential solution to wear problems associated with the use of low-lubricity diesel fuels.

  11. ULTRA-LOW SULFUR REDUCTION EMISSION CONTROL DEVICE/DEVELOPMENT OF AN ON-BOARD FUEL SULFUR TRAP

    SciTech Connect (OSTI)

    Ron Rohrbach; Gary Zulauf; Tim Gavin

    2003-04-01T23:59:59.000Z

    Honeywell is actively working on a 3-year program to develop and demonstrate proof-of-concept for an ''on-vehicle'' desulfurization fuel filter for heavy-duty diesel engines. Integration of the filter into the vehicle fuel system will reduce the adverse effects sulfur has on post combustion emission control devices such as NO{sub x} adsorbers. The NO{sub x} adsorber may be required to meet the proposed new EPA Tier II and ''2007-Rule'' emission standards. The proposed filter concept is based on Honeywell's reactive filtration technology and experience in liquids handling and conditioning. A regeneration and recycling plan for the spent filters will also be examined. We have chosen to develop and demonstrate this technology based on criteria set forth for a heavy duty CIDI engine system because it represents a more challenging set of conditions of service intervals and overall fuel usage over light duty systems. It is anticipated that the technology developed for heavy-duty applications will be applicable to light-duty as well. Further, technology developed under this proposal would also have application for the use of liquid based fuels for fuel cell power generation. The program consists of four phases. Phase I will focus on developing a concept design and analysis and resolution of technical barriers concerning removal of sulfur-containing species in low sulfur fuels. In Phase II we will concentrate on prototype filter design and preparation followed by qualification testing of this component in a fuel line application. Phase III will study life cycle and regeneration options for the spent filter. Phase IV will focus on efficacy and life testing and component integration. The project team will include a number of partners, with Honeywell International as the prime contractor. The partners include an emission control technology developer (Honeywell International), a fuel technology developer (Marathon Ashland Petroleum), a catalyst technology developer (Johnson Matthey), a CIDI engine manufacturer (Mack Trucks Inc.), a filter recycler (American Wastes Industries), and a low-sulfur fuel supplier (Equilon, a joint venture between Shell and Texaco).

  12. Update on Transition to Ultra-Low-Sulfur Diesel Fuel (released in AEO2006)

    Reports and Publications (EIA)

    2006-01-01T23:59:59.000Z

    On November 8, 2005, the Environmental Protection Agency (EPA) Administrator signed a direct final rule that will shift the retail compliance date for offering ultra-low sulfur diesel (ULSD) for highway use from September 1, 2006, to October 15, 2006. The change will allow more time for retail outlets and terminals to comply with the new 15 parts per million (ppm) sulfur standard, providing time for entities in the diesel fuel distribution system to flush higher sulfur fuel out of the system during the transition. Terminals will have until September 1, 2006, to complete their transitions to ULSD. The previous deadline was July 15, 2006.

  13. Ultra-Low Sulfur diesel Update & Future Light Duty Diesel | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your DensityEnergy U.S.-China Electric Vehicle and BatteryUS-EU-Japan

  14. Massive stars as important contributors to two micron light

    E-Print Network [OSTI]

    James E. Rhoads

    1995-03-20T23:59:59.000Z

    Near infrared light at 2 micrometers is relatively insensitive to the presence of hot young stars and dust in galaxies, and there has been recent interest in using it as a mass tracer in spiral galaxies. I present evidence that young, cool supergiant stars, whose presence is indicated by strong CO absorption in a 2.36 micrometer bandpass, dominate the 2 micrometer light from active star forming regions in the galaxy NGC 1309. The galaxy's quiescent regions, in contrast, do not show evidence of young supergiants. It follows that the 2 micrometer light comes from different stellar populations in different places, and large changes in the 2 micrometer surface brightness need not imply correspondingly large features in the galaxy's mass distribution.

  15. Ultra-low Sulfur Reduction Emission Control Device/Development of an On-board Fuel Sulfur Trap

    SciTech Connect (OSTI)

    Rohrbach, Ron; Barron, Ann

    2008-07-31T23:59:59.000Z

    Honeywell has completed working on a multiyear program to develop and demonstrate proof-of-concept for an 'on-vehicle' desulfurization fuel filter for both light duty and heavy-duty diesel engines. Integration of the filter into the vehicle fuel system will reduce the adverse effects sulfur has on post combustion emission control devices such as NOx adsorbers. The NOx adsorber may be required to meet the proposed new EPA Tier II and '2007-Rule' emission standards. The proposed filter concept is based on Honeywell's reactive filtration technology and experience in liquids handling and conditioning. A regeneration and recycling plan for the spent filters was also examined. We have chosen to develop and demonstrate this technology based on criteria set forth for a heavy duty CIDI engine system because it represents a more challenging set of conditions of service intervals and overall fuel usage over light duty systems. In the second phase of the program a light duty diesel engine test was also demonstrated. Further, technology developed under this proposal would also have application for the use of liquid based fuels for fuel cell power generation. The program consisted of four phases. Phase I focused on developing a concept design and analysis and resolution of technical barriers concerning removal of sulfur-containing species in low sulfur fuels. In Phase II concentrated on prototype filter design and preparation followed by qualification testing of this component in a fuel line application. Phase III studied life cycle and regeneration options for the spent filter. Phase IV focused on efficacy and benefits in the desulfation steps of a NOx adsorber on both a heavy and light duty engine. The project team included a number of partners, with Honeywell International as the prime contractor. The partners include an emission control technology developer (Honeywell International), a fuel technology developer (Marathon Ashland Petroleum), a catalyst technology developer (Johnson Matthey), a CIDI engine manufacturer (Navistar Inc. (formerly International Truck & Engine Corporation) and Mack Trucks Inc.), and filter recycler (American Wastes Industries).

  16. Light Emission of Argon Discharges: Importance of Heavy Particle Processes

    SciTech Connect (OSTI)

    Hartmann, Peter [Research Institute for Solid State Physics and Optics, Hungarian Academy of Sciences, POB 49, H-1525 Budapest (Hungary)

    2004-12-01T23:59:59.000Z

    Simulation studies on argon glow discharges established between flat disc electrodes, at pressure x electrode separation (pd) of 45 Pa cm are reported, with special attention to heavy-particle processes including excitation-induced light emission. The discharges are investigated through self-consistent hybrid modelling, consisting of a fluid description for components near local hydrodynamic equilibrium (slow electrons and ions), and Monte Carlo treatment of energetic electrons and heavy particles (ions and neutral atoms). The light emission profiles are analyzed for a wide range of operating conditions. The numerical results for the relative intensities and the shapes of the negative glow (created by electron impact excitation) and the cathode glow (created by heavy particle impact excitation) are in good agreement with experimental data obtained by Maric et al.

  17. Near-frictionless carbon coatings for use in fuel injectors and pump systems operating with low-sulfur diesel fuels

    SciTech Connect (OSTI)

    Erdemir, A.; Ozturk, O.; Alzoubi, M.; Woodford, J.; Ajayi, L.; Fenske, G.

    2000-01-19T23:59:59.000Z

    While sulfur in diesel fuels helps reduce friction and prevents wear and galling in fuel pump and injector systems, it also creates environmental pollution in the form of hazardous particulates and SO{sub 2} emissions. The environmental concern is the driving force behind industry's efforts to come up with new alternative approaches to this problem. One such approach is to replace sulfur in diesel fuels with other chemicals that would maintain the antifriction and antiwear properties provided by sulfur in diesel fuels while at the same time reducing particulate emissions. A second alternative might be to surface-treat fuel injection parts (i.e., nitriding, carburizing, or coating the surfaces) to reduce or eliminate failures associated with the use of low-sulfur diesel fuels. This research explores the potential usefulness of a near-frictionless carbon (NFC) film developed at Argonne National Laboratory in alleviating the aforementioned problems. The lubricity of various diesel fuels (i.e., high-sulfur, 500 ppm; low sulfur, 140 ppm; ultra-clean, 3 ppm; and synthetic diesel or Fischer-Tropsch, zero sulfur) were tested by using both uncoated and NFC-coated 52100 steel specimens in a ball-on-three-disks and a high-frequency reciprocating wear-test rig. The test program was expanded to include some gasoline fuels as well (i.e., regular gasoline and indolene) to further substantiate the usefulness of the NFC coatings in low-sulfur gasoline environments. The results showed that the NFC coating was extremely effective in reducing wear and providing lubricity in low-sulfur or sulfur-free diesel and gasoline fuels. Specifically, depending on the wear test rig, test pair, and test media, the NFC films were able to reduce wear rates of balls and flats by factors of 8 to 83. These remarkable reductions in wear rates raise the prospect for using the ultra slick carbon coatings to alleviate problems that will be caused by the use of low sulfur diesel and gasoline fuels. Surfaces of the wear scars and tracks were characterized by optical and scanning electron microscopy, and by Raman spectroscopy.

  18. Light-induced nuclear import of phytochrome-A:GFP fusion proteins is differentially regulated in transgenic tobacco

    E-Print Network [OSTI]

    Schäfer, Eberhard

    Light-induced nuclear import of phytochrome-A:GFP fusion proteins is differentially regulated. Summary Phytochromes (phy) are a family of photoreceptors that control various aspects of light inductive light conditions and for the high irradiance response (HIR) under continuous far-red light. We

  19. Iron distribution among phases in high- and low-sulfur coal fly ash

    SciTech Connect (OSTI)

    Hower, J.C.; Graham, U.M.; Rathbone, R.F. [Univ. of Kentucky, Lexington, KY (United States). Center for Applied Energy Research; Dyar, M.D.; Taylor, M.E. [West Chester Univ., PA (United States). Dept. of Geology and Astronomy

    1995-12-31T23:59:59.000Z

    Moessbauer spectroscopy, reflected-light optical microscopy, scanning-electron microscopy, wet chemical, and X-ray diffraction studies were conducted on six fly ash samples. The fly ashes, representing the combustion by-products of coals with total sulfur contents of less than 2% to greater than 4%, ranged from 17.6 to 32.0% Fe{sub 2}O{sub 3} by XRF analysis. Wet chemical analysis was used to determine the Fe{sup 3+}/{summation}Fe content of the ashes, which ranged from 72% to 83%. Optical analysis of the ashes indicated that the spinel, encompassing iron oxides of various compositions, ranges from 4.0 to 12.6% (vol.). Moessbauer analyses confirmed the presence of three Fe-bearing phases: magnetite, hematite (possibly of two different compositions), and glass. The variation in the Fe-oxidation state follows the variation in the sulfur, consequently pyrite, content of the feed coal.

  20. Navy Mobility Fuels Forecasting System Phase 5 report: Impacts of ultra low sulfur diesel fuel production on Navy fuel availability

    SciTech Connect (OSTI)

    Hadder, G.R.; Das, S.; Lee, R.; Domingo, N.; Davis, R.M.

    1989-09-01T23:59:59.000Z

    Legislation for ultra low sulfur (ULS) diesel fuel, with a greatly reduced allowable sulfur content and a new limit on aromatics content, is expected to be in place by 1995. The ULS diesel fuel has been specified to satisfy national standards for particulate emissions from heavy-duty diesel engines. The economic and engineering models of the Navy Mobility Fuels Forecasting System have been used to study the impacts of ULS diesel fuel production on other refined petroleum products, with emphasis on the quality of Navy mobility fuels. The study predicts that to produce ULS diesel fuel, Gulf and West Coast refiners will have to invest about $4.4 billion in new processing capacity. Refiners will shift aromatics from No. 2 diesel fuel to jet fuel and to No. 2 fuel oil. Therefore, particulate emissions could be transferred from the nation's highways to the airways and to communities which use No. 2 fuel oil for residential and commercial heating. The study also predicts that there will be an increase in the aromatics content of domestically produced Navy JP-5 jet fuel and F-76 marine diesel fuel. The gum-forming tendencies of F-76 an F-77 burner fuel oil will increase in most cases. The freezing point of JP-5 will improve. There will be minor changes in the cost of JP-5, but sizable reductions in the cost of F-76 and F-77. 20 refs., 2 figs., 17 tabs.

  1. The importance of 56Ni in shaping the light curves of type II supernovae

    E-Print Network [OSTI]

    Nakar, Ehud; Katz, Boaz

    2015-01-01T23:59:59.000Z

    What intrinsic properties shape the light curves of Type II supernovae (SNe)? To address this question we derive observational measures that are robust (i.e., insensitive to detailed radiative transfer) and constrain the contribution from 56Ni, as well as a combination of the ejecta mass, progenitor radius, and explosion energy. By applying our methods to a sample of type II SNe from the literature we find that 56Ni contribution is often significant. It is typically the source of about 20% of the radiated energy during the photospheric phase, and in extreme cases it even dominates. We find that the 56Ni relative contribution is anti-correlated with the luminosity decline rate, while it is not significantly correlated with other properties of the light curve. When added to other clues, this in turn suggests that the flat plateaus often observed in type II SNe are not a generic feature of the cooling envelope emission, and that without 56Ni many of the SNe that are classified as II-P would have shown a decline ...

  2. Production of low-sulfur binder pitch from high-sulfur Illinois coals. Technical report, September 1--November 30, 1994

    SciTech Connect (OSTI)

    Knight, R.A. [Inst. of Gas Technology, Chicago, IL (United States)

    1994-12-31T23:59:59.000Z

    The objective of this project is to produce electrode binder pitch with sulfur content below 0.6 wt% from high-sulfur Illinois coal mild gasification liquids. In this project, two approaches to sulfur reduction are being explored in conjunction with thermocracking: (1) the use of conventionally cleaned coal with low ({approximately}1%) sulfur as a mild gasification feedstock, and (2) direct biodesulfurization of the liquids prior to thermocracking. In Case 1, the crude pitch is being produced by mild gasification of IBC-109 coal in an existing IGT bench-scale reactor, followed by distillation of the scrubbing solvent and light-to-middle oils to isolate the crude pitch. In Case 2, the crude pitch for biodesulfurization is the same material previously studied, which was obtained from Illinois No. 6 coal tests conducted in the IGT mild gasification PRU in 1990. Biodesulfurization is to be performed by contacting the pitch with Rhodococcus Rhodochrous either as live cultures or in the form of concentrated biocatalyst. Following preparation of the crude pitches, pitch upgrading experiments are to be conducted in a continuous flash thermocracker (FTC) constructed in previous ICCI-sponsored studies. The finished pitch is then characterized for physical and chemical properties (density, softening point, QI, TI, coking value, and elemental composition), and compared to typical specifications for binder pitches. This quarter, 45 kg of IBC-109 coal was obtained and sized to 40 x 80 mesh for mild gasification. Laboratory experiments were conducted to identify means of dispersing or emulsifying pitch in water to render is accessible to biocatalysts, and exploratory desulfurization tests on one-gram pitch samples were begun.

  3. Near-Zero Emissions Oxy-Combustion Flue Gas Purification Task 3: SOx/NOx/Hg Removal for Low Sulfur Coal

    SciTech Connect (OSTI)

    Monica Zanfir; Rahul Solunke; Minish Shah

    2012-06-01T23:59:59.000Z

    The goal of this project was to develop a near-zero emissions flue gas purification technology for existing PC (pulverized coal) power plants that are retrofitted with oxycombustion technology. The objective of Task 3 of this project was to evaluate an alternative method of SOx, NOx and Hg removal from flue gas produced by burning low sulfur coal in oxy-combustion power plants. The goal of the program was to conduct an experimental investigation and to develop a novel process for simultaneously removal of SOx and NOx from power plants that would operate on low sulfur coal without the need for wet-FGD & SCRs. A novel purification process operating at high pressures and ambient temperatures was developed. Activated carbonâ??s catalytic and adsorbent capabilities are used to oxidize the sulfur and nitrous oxides to SO{sub 3} and NO{sub 2} species, which are adsorbed on the activated carbon and removed from the gas phase. Activated carbon is regenerated by water wash followed by drying. The development effort commenced with the screening of commercially available activated carbon materials for their capability to remove SO{sub 2}. A bench-unit operating in batch mode was constructed to conduct an experimental investigation of simultaneous SOx and NOx removal from a simulated oxyfuel flue gas mixture. Optimal operating conditions and the capacity of the activated carbon to remove the contaminants were identified. The process was able to achieve simultaneous SOx and NOx removal in a single step. The removal efficiencies were >99.9% for SOx and >98% for NOx. In the longevity tests performed on a batch unit, the retention capacity could be maintained at high level over 20 cycles. This process was able to effectively remove up to 4000 ppm SOx from the simulated feeds corresponding to oxyfuel flue gas from high sulfur coal plants. A dual bed continuous unit with five times the capacity of the batch unit was constructed to test continuous operation and longevity. Full-automation was implemented to enable continuous operation (24/7) with minimum operator supervision. Continuous run was carried out for 40 days. Very high SOx (>99.9%) and NOx (98%) removal efficiencies were also achieved in a continuous unit. However, the retention capacity of carbon beds for SOx and NOx was decreased from ~20 hours to ~10 hours over a 40 day period of operation, which was in contrast to the results obtained in a batch unit. These contradictory results indicate the need for optimization of adsorption-regeneration cycle to maintain long term activity of activated carbon material at a higher level and thus minimize the capital cost of the system. In summary, the activated carbon process exceeded performance targets for SOx and NOx removal efficiencies and it was found to be suitable for power plants burning both low and high sulfur coals. More efforts are needed to optimize the system performance.

  4. The Plant Cell, Vol. 11, 14451456, August 1999, www.plantcell.org 1999 American Society of Plant Physiologists Light QualityDependent Nuclear Import of the Plant

    E-Print Network [OSTI]

    Schäfer, Eberhard

    Physiologists Light Quality­Dependent Nuclear Import of the Plant Photoreceptors Phytochrome A and B StefanThe Plant Cell, Vol. 11, 1445­1456, August 1999, www.plantcell.org © 1999 American Society of Plant Institute of Plant Biology, Biological Research Center, P.O. Box 521, H-6701 Szeged, Hungary The phytochrome

  5. Lighting

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHigh SchoolIn12electron 9 5Let us countLighting Sign In About | Careers |

  6. On the importance of AlGaN electron blocking layer design for GaN-based light-emitting diodes

    SciTech Connect (OSTI)

    Sheng Xia, Chang, E-mail: xiachsh@crosslight.com.cn; Simon Li, Z. M.; Sheng, Yang [Crosslight Software Inc., China Branch, Suite 906, Building JieDi, 2790 Zhongshan Bei Road, Shanghai 200063 (China)] [Crosslight Software Inc., China Branch, Suite 906, Building JieDi, 2790 Zhongshan Bei Road, Shanghai 200063 (China)

    2013-12-02T23:59:59.000Z

    There has been confusion regarding the usefulness of AlGaN electron blocking layer (EBL) in GaN-based light-emitting diodes (LEDs) with some published experimental data indicating that the LEDs without EBL performed better than those with it. InGaN/GaN LEDs have been investigated numerically to analyze its actual effect in these devices. Simulation results show that hole blocking effect of EBL mainly determines the effectiveness of using it which is more sensitive to its Al composition, band offset ratio, and polarization charges. It is found that the choice of Al composition is critical for EBL to improve the optical performance of GaN-based LEDs.

  7. Importance of Delayed Neutrons on the Coupled Neutronic-Thermohydraulic Stability of a Natural Circulation Heavy Water-Moderated Boiling Light Water-Cooled Reactor

    SciTech Connect (OSTI)

    Nayak, A.K. [Bhaha Atomic Research Centre (India); Aritomi, M. [Tokyo Institute of Technology (Japan); Raj, V. Venkat [Bhaha Atomic Research Centre (India)

    2001-07-15T23:59:59.000Z

    The coupled neutronic-thermohydraulic stability characteristics of a natural circulation heavy water-moderated boiling light water-cooled reactor was investigated analytically considering the effects of prompt and delayed neutrons. For this purpose, the reactor considered is the Indian Advanced Heavy Water Reactor. The analytical model considers a point kinetics model for the neutron dynamics, a homogeneous two-phase flow model for the coolant thermal hydraulics, and a lumped heat transfer model for the fuel thermal dynamics. A higher mode of oscillation having a frequency much greater than the density-wave oscillation frequency was observed if prompt neutrons alone were considered. The occurrence of a higher mode of oscillation was found to be dependent on the concentration of delayed neutrons, the void reactivity coefficient, and the fuel time constant. The core inlet subcooling is found to have different effects on the decay ratio of the fundamental and higher modes of oscillations. The influences of void reactivity coefficient and fuel time constant on the fundamental and higher modes of oscillations were also found to be opposite in nature.

  8. Diesel Exhaust Emissions Control for Light-Duty Vehicles

    SciTech Connect (OSTI)

    Mital, R.; Li, J.; Huang, S. C.; Stroia, B. J.; Yu, R. C. (Cummins, Inc.); Anderson, J.A. (Argonne National Laboratory); Howden, Kenneth C. (U.S. Department of Energy)

    2003-03-01T23:59:59.000Z

    The objective of this paper is to present the results of diesel exhaust aftertreatment testing and analysis done under the FreedomCAR program. Nitrogen Oxides (NOx) adsorber technology was selected based on a previous investigation of various NOx aftertreatment technologies including non-thermal plasma, NOx adsorber and active lean NOx. Particulate Matter (PM) emissions were addressed by developing a catalyzed particulate filter. After various iterations of the catalyst formulation, the aftertreatment components were integrated and optimized for a light duty vehicle application. This compact exhaust aftertreatment system is dual leg and consists of a sulfur trap, NOx adsorbers, and catalyzed particulate filters (CPF). During regeneration, supplementary ARCO ECD low-sulfur diesel fuel is injected upstream of the adsorber and CPF in the exhaust. Steady state and transient emission test results with and without the exhaust aftertreatment system (EAS) are presented. Results of soot filter regeneration by injecting low-sulfur diesel fuel and slip of unregulated emissions, such as NH3, are discussed. Effects of adsorber size and bypass strategy on NOx conversion efficiency and fuel economy penalty are also presented in this paper. The results indicate that if the supplementary fuel injection is optimized, NH3 slip is negligible. During the FTP cycle, injection of low sulfur diesel fuel can create temperature exotherms high enough to regenerate a loaded CPF. With the optimized NOx adsorber regeneration strategies the fuel injection penalty can be reduced by 40 to 50%. Results for various other issues like low temperature light off, reductant optimization, exhaust sulfur management, system integration and design trade-off, are also presented and discussed in this paper. (SAE Paper SAE-2003-01-0041 © 2003 SAE International. This paper is published on this website with permission from SAE International. As a user of this website, you are permitted to view this paper on-line, download this pdf file and print one copy of this paper at no cost for your use only. The downloaded pdf file and printout of this SAE paper may not be copied, distributed or forwarded to others or for the use of others.)

  9. Sandia Energy - (Lighting and) Solid-State Lighting: Science...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    on the third and upcoming revolution (illumination). Topics cover the basics of light-emitting diode (LED) operation; a 200-year history of lighting technology; the importance of...

  10. Sandia National Laboratories: (Lighting and) Solid-State Lighting...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    on the third and upcoming revolution (illumination). Topics cover the basics of light-emitting diode (LED) operation; a 200-year history of lighting technology; the importance of...

  11. Crude Imports

    Gasoline and Diesel Fuel Update (EIA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for On-Highway4,1,50022,3,,,,6,1,9,1,50022,3,,,,6,1,Decade Year-0E (2001)gasoline prices4Consumption TheX Imeans ofFHomeImports -

  12. Advanced Demand Responsive Lighting

    E-Print Network [OSTI]

    Advanced Demand Responsive Lighting Host: Francis Rubinstein Demand Response Research Center demand responsive lighting systems ­ Importance of dimming ­ New wireless controls technologies · Advanced Demand Responsive Lighting (commenced March 2007) #12;Objectives · Provide up-to-date information

  13. Low-Pressure Sodium Lighting Basics

    Broader source: Energy.gov [DOE]

    Low-pressure sodium lighting provides more energy-efficient outdoor lighting than high-intensity discharge lighting, but it has very poor color rendition. Typical applications include highway and security lighting, where color is not important.

  14. A novel coal feeder for production of low sulfur fuel

    SciTech Connect (OSTI)

    Khang, S.J.; Lin, L.; Keener, T.C.; Yeh, P.

    1991-01-01T23:59:59.000Z

    A dual-screw feeder was designed for desulfurization of coal. This reactor contains two screw tubes, the inner tube acting as a coal pyrolizer and the outer tube acting as a desulfurizer with hot calcined lime pellets or other renewable sorbent pellets. The objectives of this project is to study the feasibility of an advanced concept of desulfurization and possibly some denitrification in this coal feeder. In this year, two basic studies have been performed: (1) the desulfurization and (2) the denitrification due to mild pyrolysis. Specifically, the following tasks have been performed: (1) Setting up the Dual-Screw reactor, (2) Determination of the pyrolysis product and the sulfur distribution in char, tar and gas based on experimental data, (3) Study of the devolatilization, the desulfurization kinetics and the denitrification kinetics and obtaining the basic kinetic parameters, (4) Study of the sulfur removal efficiency of lime pellets fed into the outer tube of the dual-feeder reactor, (5) Study of the effect of the coal particle size on pyrolysis and desulfurization, (6) Study of the coal pyrolysis and desulfurization using a TGA(Thermal Gravimetric Analyzer).

  15. Smart lighting: New Roles for Light

    E-Print Network [OSTI]

    Salama, Khaled

    Smart lighting: New Roles for Light in the Solid State Lighting World Robert F. Karlicek, Jr. Director, Smart Lighting Engineering Research Center Professor, Electrical, Systems and Computer Lighting · What is Smart Lighting · Technology Barriers to Smart Lighting · Visible Light Communications

  16. Commercial Lighting

    Broader source: Energy.gov [DOE]

    Commercial lighting accounts for more than 20 percent of total commercial building energy use. The Energy Department works to reduce lighting energy use through research and deployment.

  17. Fact #837: September 8, Gap between Net Imports and Total Imports...

    Broader source: Energy.gov (indexed) [DOE]

    exports) were 6.2 million barrels per day in 2013 - the lowest since the 1980's (dark blue line). The widening gap between total imports (light blue line) and net imports (dark...

  18. Effect of Biodiesel Blending on the Speciation of Soluble Organic Fraction from a Light Duty Diesel Engine

    SciTech Connect (OSTI)

    Strzelec, Andrea [ORNL] [ORNL; Storey, John Morse [ORNL] [ORNL; Lewis Sr, Samuel Arthur [ORNL] [ORNL; Daw, C Stuart [ORNL] [ORNL; Foster, Prof. Dave [University of Wisconsin] [University of Wisconsin; Rutland, Prof. Christopher J. [University of Wisconsin] [University of Wisconsin

    2010-01-01T23:59:59.000Z

    Soy methyl ester (SME) biodiesel was volumetrically blended with 2007 certification ultra low sulfur diesel (ULSD) fuel and run in a 1.7L direct-injection common rail diesel engine at one speed-load point (1500rpm, 2.6bar BMEP). Engine fueling rate and injection timing were adjusted to maintain a constant load, while particulate samples were collected in a diesel particulate filter (DPF) and with a dilution tunnel sampling train. The samples collected at these two locations were found to contain different levels of soluble organic fraction (SOF) and the different hydrocarbon species in the SOF. This observation indicates that traditional SOF measurements, in light of the specific sampling procedure used, may not be appropriate to DPF applications.

  19. Light Properties Light travels at the speed of light `c'

    E-Print Network [OSTI]

    Mojzsis, Stephen J.

    LIGHT!! #12;Light Properties Light travels at the speed of light `c' C = 3 x 108 m/s Or 190,000 miles/second!! Light could travel around the world about 8 times in one second #12;What is light?? Light is a "wave packet" A photon is a "light particle" #12;Electromagnetic Radiation and You Light is sometimes

  20. Smart Lighting Controller!! Smart lighting!

    E-Print Network [OSTI]

    Anderson, Betty Lise

    1! Smart Lighting Controller!! #12;2! Smart lighting! No need to spend energy lighting the room if://blogs.stthomas.edu/realestate/2011/01/24/residential-real-estate-professionals-how-do-you- develop feedback! There is a connection between the output and the input! Therefore forces inputs to same voltage

  1. Catalyzed Diesel Particulate Filter Performance in a Light-Duty Vehicle

    SciTech Connect (OSTI)

    Sluder, C.S.

    2001-04-23T23:59:59.000Z

    Light-duty chassis dynamometer driving cycle tests were conducted on a Mercedes A170 diesel vehicle with various sulfur-level fuels and exhaust emission control systems. Triplicate runs of a modified light-duty federal test procedure (FTP), US06 cycle, and SCO3 cycle were conducted with each exhaust configuration and fuel. Ultra-low sulfur (3-ppm) diesel fuel was doped to 30- and 150-ppm sulfur so that all other fuel properties remained the same. The fuels used in these experiments met the specifications of the fuels from the DECSE (Diesel Emission Control Sulfur Effects) program. Although the Mercedes A170 vehicle is not available in the US, its emissions in the as tested condition fell within the U.S. Tier 1 full useful life standards with the OEM catalysts installed. Tests with the OEM catalysts removed showed that the OEM catalysts reduced PM emissions from the engine-out condition by 30-40% but had negligible effects on NOx emissions. Fuel sulfur level had very little effect on th e OEM catalyst performance. A prototype catalyzed diesel particulate filter (CDPF) mounted in an underfloor configuration reduced particulate matter emissions by more than 90% compared to the factory emissions control system. The results show that the CDPF did not promote any significant amounts of SO{sub 2}-to-sulfate conversion during these light-duty drive cycles.

  2. Cerenkov Light

    ScienceCinema (OSTI)

    Slifer, Karl

    2014-05-22T23:59:59.000Z

    The bright blue glow from nuclear reactors is Cerenkov light. Karl Slifer describes how nuclear physicists can use this phenomenon to study the nucleus of the atom.

  3. Cerenkov Light

    SciTech Connect (OSTI)

    Slifer, Karl

    2013-06-13T23:59:59.000Z

    The bright blue glow from nuclear reactors is Cerenkov light. Karl Slifer describes how nuclear physicists can use this phenomenon to study the nucleus of the atom.

  4. Lighting Renovations

    Broader source: Energy.gov [DOE]

    When undertaking a lighting renovation in a Federal building, daylighting is the primary renewable energy opportunity. Photovoltaics (PV) also present an excellent opportunity. While this guide...

  5. Dark Beaches – FDOT’s Continued Efforts to Implement Environmentally Sensitive Lighting Systems

    E-Print Network [OSTI]

    Broadwell, Ann

    2007-01-01T23:59:59.000Z

    address coastal roadway lighting and its impacts on adjacentUSA Abstract Artificial lighting has two important effectscontribute to many beach lighting problems. The existing

  6. World Oil Prices in AEO2007 (released in AEO2007)

    Reports and Publications (EIA)

    2007-01-01T23:59:59.000Z

    Over the long term, the Annual Energy Outlook 2007 (AEO) projection for world oil prices -- defined as the average price of imported low-sulfur, light crude oil to U.S. refiners -- is similar to the AEO2006 projection. In the near term, however, AEO2007 projects prices that are $8 to $10 higher than those in AEO2006.

  7. Strategy Guideline: High Performance Residential Lighting

    SciTech Connect (OSTI)

    Holton, J.

    2012-02-01T23:59:59.000Z

    The Strategy Guideline: High Performance Residential Lighting has been developed to provide a tool for the understanding and application of high performance lighting in the home. The high performance lighting strategies featured in this guide are drawn from recent advances in commercial lighting for application to typical spaces found in residential buildings. This guide offers strategies to greatly reduce lighting energy use through the application of high quality fluorescent and light emitting diode (LED) technologies. It is important to note that these strategies not only save energy in the home but also serve to satisfy the homeowner's expectations for high quality lighting.

  8. import java.io.IOException; import java.net.URI;

    E-Print Network [OSTI]

    Ricci, Laura

    import java.io.IOException; import java.net.URI; import java.util.Enumeration; import net.jxta.discovery.DiscoveryService; import net.jxta.document.AdvertisementFactory; import net.jxta.document.Element; import net.jxta.document.MimeMediaType; import net.jxta.document.StructuredDocument; import net.jxta.document.StructuredDocumentFactory; import

  9. Light Computing

    E-Print Network [OSTI]

    Gordon Chalmers

    2006-10-13T23:59:59.000Z

    A configuration of light pulses is generated, together with emitters and receptors, that allows computing. The computing is extraordinarily high in number of flops per second, exceeding the capability of a quantum computer for a given size and coherence region. The emitters and receptors are based on the quantum diode, which can emit and detect individual photons with high accuracy.

  10. Residential Lighting

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What's PossibleRadiation Protection Technical squestionnairesquestionnaires AgreementLighting

  11. Lighting Inventory Lighting Theatre and Drama

    E-Print Network [OSTI]

    Indiana University

    Lighting Inventory Lighting Theatre and Drama Description Totals R.Halls Wells- Metz Light ERS ETC SourceFour 25 25 50 degree ERS Strand Lighting 64 14 24 12 14 36 degree ERS ETC Source Four 15 15 36 degree ERS Strand Lighting 124 60 58 2 4 26 degree ERS ETC SourceFour 2 2 26 degree ERS Strand

  12. Windows and lighting program

    SciTech Connect (OSTI)

    Not Available

    1990-06-01T23:59:59.000Z

    More than 30% of all energy use in buildings is attributable to two sources: windows and lighting. Together they account for annual consumer energy expenditures of more than $50 billion. Each affects not only energy use by other major building systems, but also comfort and productivity -- factors that influence building economics far more than does direct energy consumption alone. Windows play a unique role in the building envelope, physically separating the conditioned space from the world outside without sacrificing vital visual contact. Throughout the indoor environment, lighting systems facilitate a variety of tasks associated with a wide range of visual requirements while defining the luminous qualities of the indoor environment. Windows and lighting are thus essential components of any comprehensive building science program. Despite important achievements in reducing building energy consumption over the past decade, significant additional savings are still possible. These will come from two complementary strategies: (1) improve building designs so that they effectively apply existing technologies and extend the market penetration of these technologies; and (2) develop advanced technologies that increase the savings potential of each application. Both the Windows and Daylighting Group and the Lighting System Research Group have made substantial contributions in each of these areas, and continue to do so through the ongoing research summarized here. 23 refs., 16 figs.

  13. LED Lighting Basics

    Broader source: Energy.gov [DOE]

    Light-Emitting diodes (LEDs) efficiently produce light in a fundamentally different way than any legacy or traditional source of light.

  14. Light Source

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHigh SchoolIn12electron 9 5Let us count theLienertLift Forces in a Light

  15. auxin importer implications: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    7, 2014 IMPORTANT NOTICE Total vs. Free Kappa and Lambda Light Chains EQAS Serum Proteins Program BC05BC10 Dear Valued Participant, Please be advised that as of cycle 41, both...

  16. Company Level Imports Archives

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 111 1,613 122 40Coal Stocks at CommercialDecadeReservesYear21Company Level Imports Company Level

  17. Sustainable Office Lighting Options

    E-Print Network [OSTI]

    Massachusetts at Amherst, University of

    Sustainable Office Lighting Options Task Lighting: Task lighting is a localized method of lighting a workspace so that additional, unnecessary lighting is eliminated, decreasing energy usage and costs. Illumination levels in the targeted work areas are higher with task lighting than with the ambient levels

  18. Important U-PASS information

    E-Print Network [OSTI]

    Yetisgen-Yildiz, Meliha

    Bicycling BikeSport Recycled Cycles Student Health Advisory Quorum (SHAQ) Car Services Auto Care & Tires Clothes Red Light Vintage & Costume Gifts & Merchandise Bamboo Hardwoods Dreaming Comics

  19. Human Pathogen Importation Importing "Human" Pathogens from Outside Canada

    E-Print Network [OSTI]

    Human Pathogen Importation Importing "Human" Pathogens from Outside Canada 1) Permits be obtained from the Public Health Agency Canada (PHAC) to facilitate customs clearance. 2) If a permit

  20. Lighting Options for Homes.

    SciTech Connect (OSTI)

    Baker, W.S.

    1991-04-01T23:59:59.000Z

    This report covers many aspects of various lighting options for homes. Types of light sources described include natural light, artificial light, incandescent lamps, fluorescent lamps, and high intensity discharge lamps. A light source selection guide gives the physical characteristics of these, design considerations, and common applications. Color, strategies for efficient lighting, and types of lighting are discussed. There is one section giving tips for various situations in specific rooms. Rooms and types of fixtures are shown on a matrix with watts saved by using the recommended type lighting for that room and room location. A major emphasis of this report is saving energy by utilizing the most suitable, recommended lighting option. (BN)

  1. Mobile lighting apparatus

    DOE Patents [OSTI]

    Roe, George Michael; Klebanoff, Leonard Elliott; Rea, Gerald W; Drake, Robert A; Johnson, Terry A; Wingert, Steven John; Damberger, Thomas A; Skradski, Thomas J; Radley, Christopher James; Oros, James M; Schuttinger, Paul G; Grupp, David J; Prey, Stephen Carl

    2013-05-14T23:59:59.000Z

    A mobile lighting apparatus includes a portable frame such as a moveable trailer or skid having a light tower thereon. The light tower is moveable from a stowed position to a deployed position. A hydrogen-powered fuel cell is located on the portable frame to provide electrical power to an array of the energy efficient lights located on the light tower.

  2. Light disappears rapidly (exponentially)

    E-Print Network [OSTI]

    Kudela, Raphael M.

    #12;#12;#12;#12;Light disappears rapidly (exponentially) with depth At the same time, the color of the light shifts #12;#12;#12;#12;· Euphotic zone ­ plentiful light ­ 0-100 m (about) · Dysphotic zone ­ very, very little light ­ 100-1000 m (about) · Aphotic zone ­ no light ­ below 1000 m #12;Sunlight in Water

  3. New Light Sources for Tomorrow's Lighting Designs

    E-Print Network [OSTI]

    Krailo, D. A.

    can ever be saved on that monthly energy bill. During the past several years, many new light sources have been developed and introduced. These product introductions have not been limited to anyone lamp type, but instead may be found in fila ment..., fluorescent and high intensity discharge lamp families. Man , ufacturers of light sources have two basic goals for new product development. These goals are high efficiency lighting and improved colo'r rendering properties. High efficiency lighting may take...

  4. EK101 Engineering Light Smart Lighting

    E-Print Network [OSTI]

    Bifano, Thomas

    EK101 Engineering Light Smart Lighting Homework for 9/10 1. Make an estimate (using if the patent is granted.) 3. What is a lumen? A lux? How are the two related? How would you use a lux meter, (Lux, Lumens/m2) Luminous Flux: Perceivable light power from a source, (Lumens) Use the lux meter

  5. Important Trinity / NERSC-8 Documents

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    RFP Important Trinity NERSC-8 Documents Important Trinity NERSC-8 Documents Trinity NERSC-8 Use Case Scenarios for Burst Buffer and Power Management PDF Facility Limits...

  6. EIAs U.S. Crude Oil Import Tracking Tool

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    onshore production will be dominated by light crudes, issues surrounding the absorption of domestic crude by increased runs, by like-for-like replacement of import streams...

  7. Specific light in sculpture

    E-Print Network [OSTI]

    Powell, John William

    1989-01-01T23:59:59.000Z

    Specific light is defined as light from artificial or altered natural sources. The use and manipulation of light in three dimensional sculptural work is discussed in an historic and contemporary context. The author's work ...

  8. Light Duty Combustion Research: Advanced Light-Duty Combustion...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Light Duty Combustion Research: Advanced Light-Duty Combustion Experiments Light Duty Combustion Research: Advanced Light-Duty Combustion Experiments 2009 DOE Hydrogen Program and...

  9. Exciting White Lighting

    Broader source: Energy.gov [DOE]

    Windows that emit light and are more energy efficient? Universal Display’s PHOLED technology enables windows that have transparent light-emitting diodes in them.

  10. Caring for Important Papers after a Flood

    E-Print Network [OSTI]

    FCS Project Team - FDRM UNIT

    2005-09-30T23:59:59.000Z

    process, it may be worth the effort. Separate the pages to prevent musty odors. ? When the books are thoroughly dry, close them and use C-clamps to help them retain their shape. Wipe vinyl and leather book covers with a light coating of petroleum jelly..., University of California Cooperative Extension. Caring for Important Papers after a Flood Produced by AgriLife Communications and Marketing, The Texas A&M System Extension publications can be found on the Web at: http://AgriLifebookstore.org Visit the Texas...

  11. Introduction: Why energy-effective lighting?

    SciTech Connect (OSTI)

    Johnson, K.R.

    1996-01-01T23:59:59.000Z

    Since the oil crisis of the 1970s, lighting applications have evolved from delamping to the energy-efficient components that have been the mainstay into the 1980s and early 1990s. This evolution has led the industry to the realization of the need to focus on energy-effective lighting. The quality of lighting must first be defined, and then the most energy-efficient technologies and systems available must be provided. Energy cost is the dominant cost of operating a lighting system, so as one moves down into lower wattages (down to 1 W/sq ft) and as regulations and needs in the commercial sector change, such as the continually increasing use of video display terminals, one must take productivity into account. Because it is hard to define productivity, it is difficult to prove an impact. It costs 20 to 50% more for a lighting system designer to focus on high-quality designs, taking into account the lighting needs versus simply installing fluorescent fixtures. It is important that changes in the lighting system do not negatively affect productivity, and enhancing the quality of lighting can prove to be a good investment. Achieving energy-effective lighting is difficult. It takes extra effort to define the metrics, combining the efficiency, controls, and quality indices. As a cost benefit, energy-efficiency improvements are important, and are both a utility issue and a customer issue. The energy savings can be used to invest in productivity improvement. Occupant comfort is paramount for energy-effective lighting and long-term effectiveness: if the customer isn`t satisfied with the lighting system, the system will not endure and will not produce lasting savings. Therefore, it`s important to invest in energy-efficiency, not through components but through energy-effective lighting. The productivity issues outwiegh any of the energy or investment issues.

  12. LEDs for Energy Efficient Greenhouse Lighting

    E-Print Network [OSTI]

    Singh, Devesh; Meinhardt-Wollweber, Merve; Roth, Bernhard

    2014-01-01T23:59:59.000Z

    Light energy is an important factor for plant growth. In regions where the natural light source, i.e. solar radiation, is not sufficient for growth optimization, additional light sources are being used. Traditional light sources such as high pressure sodium lamps and other metal halide lamps are not very efficient and generate high radiant heat. Therefore, new sustainable solutions should be developed for energy efficient greenhouse lighting. Recent developments in the field of light source technologies have opened up new perspectives for sustainable and highly efficient light sources in the form of light-emitting diodes, i.e. LEDs, for greenhouse lighting. This review focuses on the potential of LEDs to replace traditional light sources in the greenhouse. In a comparative economic analysis of traditional vs. LED lighting, we show that the introduction of LEDs allows reduction of the production cost of vegetables in the long-run of several years, due to the high energy efficiency, low maintenance cost and lon...

  13. Cold Light from Hot Atoms and Molecules

    SciTech Connect (OSTI)

    Lister, Graeme [OSRAM SYLVANIA, CRSL, 71 Cherry Hill Drive, Beverly, MA (United States); Curry, John J. [National Institute of Standards and Technology, Gaithersburg, MD (United States)

    2011-05-11T23:59:59.000Z

    The introduction of rare earth atoms and molecules into lighting discharges led to great advances in efficacy of these lamps. Atoms such as Dy, Ho and Ce provide excellent radiation sources for lighting applications, with rich visible spectra, such that a suitable combination of these elements can provide high quality white light. Rare earth molecules have also proved important in enhancing the radiation spectrum from phosphors in fluorescent lamps. This paper reviews some of the current aspects of lighting research, particularly rare earth chemistry and radiation, and the associated fundamental atomic and molecular data.

  14. PFP Emergency Lighting Study

    SciTech Connect (OSTI)

    BUSCH, M.S.

    2000-02-02T23:59:59.000Z

    NFPA 101, section 5-9 mandates that, where required by building classification, all designated emergency egress routes be provided with adequate emergency lighting in the event of a normal lighting outage. Emergency lighting is to be arranged so that egress routes are illuminated to an average of 1.0 footcandle with a minimum at any point of 0.1 footcandle, as measured at floor level. These levels are permitted to drop to 60% of their original value over the required 90 minute emergency lighting duration after a power outage. The Plutonium Finishing Plant (PFP) has two designations for battery powered egress lights ''Emergency Lights'' are those battery powered lights required by NFPA 101 to provide lighting along officially designated egress routes in those buildings meeting the correct occupancy requirements. Emergency Lights are maintained on a monthly basis by procedure ZSR-12N-001. ''Backup Lights'' are battery powered lights not required by NFPA, but installed in areas where additional light may be needed. The Backup Light locations were identified by PFP Safety and Engineering based on several factors. (1) General occupancy and type of work in the area. Areas occupied briefly during a shiftly surveillance do not require backup lighting while a room occupied fairly frequently or for significant lengths of time will need one or two Backup lights to provide general illumination of the egress points. (2) Complexity of the egress routes. Office spaces with a standard hallway/room configuration will not require Backup Lights while a large room with several subdivisions or irregularly placed rooms, doors, and equipment will require Backup Lights to make egress safer. (3) Reasonable balance between the safety benefits of additional lighting and the man-hours/exposure required for periodic light maintenance. In some plant areas such as building 236-Z, the additional maintenance time and risk of contamination do not warrant having Backup Lights installed in all rooms. Sufficient light for egress is provided by existing lights located in the hallways.

  15. Importance Driven Rendering Using Importance Information in the Rendering Process

    E-Print Network [OSTI]

    Schumann, Heidrun

    Importance Driven Rendering ­ Using Importance Information in the Rendering Process R. Schultz describes the concept of using importance in- formation in the rendering process. Doing so, we can adapt the rendering time and image quality to the requirements of a user. For that, we discuss two problems

  16. Explaining low sulfur dioxide allowance prices : the effect of expectation errors and irreversibility

    E-Print Network [OSTI]

    Montero, Juan-Pablo

    1998-01-01T23:59:59.000Z

    The low price of allowances has been a frequently noted featured of the implementation of the sulfur dioxide emissions market of the U.S. Acid Rain Program. This paper presents theoretical and numerical analyses that explain ...

  17. ashless low-sulfur fuel: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    cell power generation systems provide a clean alternative to the conventional fossil fuel based systems. Fuel cell systems have a high e?ciency and use easily available...

  18. Method to improve lubricity of low-sulfur diesel and gasoline fuels

    DOE Patents [OSTI]

    Erdemir, Ali

    2004-08-31T23:59:59.000Z

    A method for providing lubricity in fuels and lubricants includes adding a boron compound to a fuel or lubricant to provide a boron-containing fuel or lubricant. The fuel or lubricant may contain a boron compound at a concentration between about 30 ppm and about 3,000 ppm and a sulfur concentration of less than about 500 ppm. A method of powering an engine to minimize wear, by burning a fuel containing boron compounds. The boron compounds include compound that provide boric acid and/or BO.sub.3 ions or monomers to the fuel or lubricant.

  19. Demand, Supply, and Price Outlook for Low-Sulfur Diesel Fuel

    Gasoline and Diesel Fuel Update (EIA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for On-Highway4,1,50022,3,,,,6,1,9,1,50022,3,,,,6,1,Decade Year-0E (2001)gasoline353/06) 2Yonthly Energy : 42Q)2Q)6)2k(STEO) To

  20. No. 2 Diesel, Low-Sulfur Prices - Sales to End Users

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What's Possible for Renewable Energy:Nanowire Solar541,9337,2AprilBig Eddy ArcheologicalCentral Atlantic

  1. DOE Will Convert Northeast Home Heating Oil Reserve to Ultra Low Sulfur

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: Theof"WaveInteractionsMaterials | Department

  2. No. 2 Diesel, Low-Sulfur Prices - Sales to End Users

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5 Tables July 1996 Energy Information Administration Office ofthrough 1996) inThousandWithdrawals (MillionNine8 2.415 - - - - 1994-20143

  3. Lighting and Daylight Harvesting

    E-Print Network [OSTI]

    Bos, J.

    2011-01-01T23:59:59.000Z

    exposing us to the latest products and technologies. Daylight Harvesting A system of controlling the direction and the quantity of light both natural and artificial within a given space. This implies: Control of fenestration in terms of size..., transmission and direction. Control of reflected light within a space. Control of electric light in terms of delivery and amount Daylight harvesting systems are typically designed to maintain a minimum recommended light level. This light level...

  4. EK101 Engineering Light Project: Evaluate Residential Lighting

    E-Print Network [OSTI]

    Bifano, Thomas

    EK101 Engineering Light Project: Evaluate Residential Lighting Compare technical and economic characteristics of three sources of residential light. Two teams of four complete the same project Engineering Light Project: Evaluate Residential Lighting Project Assignment: Evaluate current options

  5. U.S. Department of Energy and International Association of Lighting Designers Partner to Improve Energy Efficiency in Lighting Systems

    Broader source: Energy.gov [DOE]

    The U.S. Department of Energy (DOE) and the International Association of Lighting Designers (IALD) signed a Memorandum of Understanding (MOU) in November 2008 to work cooperatively toward improving the efficient use of energy by lighting equipment and systems. The MOU emphasizes the importance of minimizing the impact of energy use on the environment in support of DOE SSL programs on lighting quality.

  6. Plant Importation Importing "Plant Material" From Outside Canada

    E-Print Network [OSTI]

    Plant Importation Importing "Plant Material" From Outside Canada 1) Determine whether) If a permit is required from the CFIA* (a division of Agriculture Canada), please go to the CFIA website Agency Canada (PHAC) or the Canadian Food Inspection Agency (CFIA). #12;

  7. Deficiencies of Lighting Codes and Ordinances in Controlling Light Pollution from Parking Lot Lighting Installations

    E-Print Network [OSTI]

    Royal, Emily

    2012-05-31T23:59:59.000Z

    The purpose of this research was to identify the main causes of light pollution from parking lot electric lighting installations and highlight the deficiencies of lighting ordinances in preventing light pollution. Using an industry-accepted lighting...

  8. OpenGL Lighting 13. OpenGL Lighting

    E-Print Network [OSTI]

    McDowell, Perry

    OpenGL Lighting 13. OpenGL Lighting · Overview of Lighting in OpenGL In order for lighting to have an effect in OpenGL, two things are required: A light An object to be lit Lights can be set to any color determine how they reflect the light which hits them. The color(s) of an object is determined

  9. Adaptive Street Lighting Controls

    Broader source: Energy.gov [DOE]

    This two-part DOE Municipal Solid-State Street Lighting Consortium webinar focused on LED street lighting equipped with adaptive control components. In Part I, presenters Amy Olay of the City of...

  10. Sandia National Laboratories: Lighting

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Lighting Solid-State Lighting Science EFRC On November 11, 2010, in Welcome History of Incandescence History of LEDs Grand Challenges Our EFRC SSLS-EFRC Contacts News Publications...

  11. Lighting studies: interpreting lighting styles from traditional media in computer-generated imagery

    E-Print Network [OSTI]

    Hong, Cindy Christine

    2002-01-01T23:59:59.000Z

    is particularly important. Often, characters are given a preliminary lighting set-up without regard for or knowledge o f the background. Adjustments are made once the character is added to the background. That the characters' lighting differs ? sometimes quite..., many 3D objects w i l l hide a light placed directly behind them (Figure II. La . ) . A digital lighter must know how to work around this problem, in this case either by placing the light at a slightly different angle (Figure I l . l .b . ) , adding...

  12. Handleiding Import & Export RSS Feeds

    E-Print Network [OSTI]

    Galis, Frietson

    Handleiding Import & Export RSS Feeds Version: 1.0 RSS Feeds Date: 17-04-2013 #12;2 Exporteren RSS bestand. 1) Selecteer "Import and export.." 2) Selecteer "Export to a file" en vervolgens "Next" #12;3 3) Selecteer "Feeds" en vervolgens "Next" 4) Selecteer "Export" Wanneer u geen locatie opgeeft, zal Internet

  13. Light emitting device comprising phosphorescent materials for white light generation

    DOE Patents [OSTI]

    Thompson, Mark E.; Dapkus, P. Daniel

    2014-07-22T23:59:59.000Z

    The present invention relates to phosphors for energy downconversion of high energy light to generate a broadband light spectrum, which emit light of different emission wavelengths.

  14. Light Rail Transit Strengthening

    E-Print Network [OSTI]

    Minnesota, University of

    Light Rail Transit Improving mobility Easing congestion Strengthening our communities Central Corridor Communicating to the Public During Major Construction May 25, 2011 #12;2 Light Rail Transit;Light Rail Transit Central Corridor Route and Stations 3 · 18 new stations · 9.8 miles of new double

  15. Light extraction from organic light-emitting diodes for lighting applications by sand-blasting

    E-Print Network [OSTI]

    Light extraction from organic light-emitting diodes for lighting applications by sand@ust.hk Abstract: Light extraction from organic light-emitting diodes (OLEDs) by scattering the light is one of the effective methods for large-area lighting applications. In this paper, we present a very simple and cost

  16. Photonic crystal light source

    DOE Patents [OSTI]

    Fleming, James G. (Albuquerque, NM); Lin, Shawn-Yu (Albuquerque, NM); Bur, James A. (Corrales, NM)

    2004-07-27T23:59:59.000Z

    A light source is provided by a photonic crystal having an enhanced photonic density-of-states over a band of frequencies and wherein at least one of the dielectric materials of the photonic crystal has a complex dielectric constant, thereby producing enhanced light emission at the band of frequencies when the photonic crystal is heated. The dielectric material can be a metal, such as tungsten. The spectral properties of the light source can be easily tuned by modification of the photonic crystal structure and materials. The photonic crystal light source can be heated electrically or other heating means. The light source can further include additional photonic crystals that exhibit enhanced light emission at a different band of frequencies to provide for color mixing. The photonic crystal light source may have applications in optical telecommunications, information displays, energy conversion, sensors, and other optical applications.

  17. Steam Coal Import Costs - EIA

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    Steam Coal Import Costs for Selected Countries U.S. Dollars per Metric Ton1 (Average Unit Value, CIF2) Country 2001 2002 2003 2004 2005 2006 2007 2008 2009 Belgium 46.96 39.34...

  18. Foundations and Light Compass Foundations and Light Compass

    E-Print Network [OSTI]

    Wong, Jennifer L.

    Foundations and Light Compass Case Study Foundations and Light Compass Case Study Jennifer L. WongQuantitative Sensor--centric Designcentric Design Light CompassLight Compass ­­ Models and Abstractions Contaminant Transport Marine Microorganisms Ecosystems, Biocomplexity What is a Light Compass?What is a Light

  19. Lighting and Surfaces 11.1 Introduction to Lighting

    E-Print Network [OSTI]

    Boyd, John P.

    Chapter 11 Lighting and Surfaces 11.1 Introduction to Lighting Three-dimensional surfaces can react to light, and how computer graphics simulates this. There are three species of light (or "illumination models"): 1. Intrinsic (self-emitting) 2. Ambient light (sometimes called "diffuse light") 3

  20. Arnold Schwarzenegger LIGHTING RESEARCH PROGRAM

    E-Print Network [OSTI]

    Project Summaries ELEMENT 2: ADVANCE LIGHTING TECHNOLOGIES PROJECT 2.1 LIGHT EMITTING DIODE (LED light emitting diodes (LED) technology for general lighting applications by developing a task lamp

  1. Dim Light at Night Increases Immune Function in Nile Grass Rats, a Diurnal Rodent

    E-Print Network [OSTI]

    Nelson, Randy J.

    Dim Light at Night Increases Immune Function in Nile Grass Rats, a Diurnal Rodent Laura K. Fonken lighting during the 20th century, human and nonhuman animals became exposed to high levels of light significant implications for certain ecological niches because of the important influence light exerts

  2. High efficiency incandescent lighting

    DOE Patents [OSTI]

    Bermel, Peter; Ilic, Ognjen; Chan, Walker R.; Musabeyoglu, Ahmet; Cukierman, Aviv Ruben; Harradon, Michael Robert; Celanovic, Ivan; Soljacic, Marin

    2014-09-02T23:59:59.000Z

    Incandescent lighting structure. The structure includes a thermal emitter that can, but does not have to, include a first photonic crystal on its surface to tailor thermal emission coupled to, in a high-view-factor geometry, a second photonic filter selected to reflect infrared radiation back to the emitter while passing visible light. This structure is highly efficient as compared to standard incandescent light bulbs.

  3. National Synchrotron Light Source

    ScienceCinema (OSTI)

    BNL

    2009-09-01T23:59:59.000Z

    A tour of Brookhaven's National Synchrotron Light Source (NSLS), hosted by Associate Laboratory Director for Light Sources, Stephen Dierker. The NSLS is one of the world's most widely used scientific research facilities, hosting more than 2,500 guest researchers each year. The NSLS provides intense beams of infrared, ultraviolet, and x-ray light for basic and applied research in physics, chemistry, medicine, geophysics, environmental, and materials sciences.

  4. LED Lighting Retrofit

    E-Print Network [OSTI]

    Shaw-Meadow, N.

    2011-01-01T23:59:59.000Z

    ? Municipal Street Lighting Consortium ? American Public Power Association (APPA) ? Demonstration in Energy Efficiency Development (DEED) ? Source of funding and database of completed LED roadway projects 6 Rules of the Road ESL-KT-11-11-57 CATEE 2011..., 2011 ? 9 Solar-Assisted LED Case Study LaQuinta Hotel, Cedar Park, Texas ? Utilizes 18 - ActiveLED Solar-Assisted Parking Lot Lights ? Utilizes ?power management? to extend battery life while handling light output ? Reduces load which reduces PV...

  5. Edmund G. Brown Jr. LIGHTING CALIFORNIA'S FUTURE

    E-Print Network [OSTI]

    Edmund G. Brown Jr. Governor LIGHTING CALIFORNIA'S FUTURE: SMART LIGHT-EMITTING DIODE LIGHTING's Future: Smart LightEmitting Diode Lighting in Residential Fans. California Energy Commission, PIER

  6. Comparing Light Bulbs

    Broader source: Energy.gov [DOE]

    In this exercise, students will use a light to demonstrate the difference between being energy-efficient and energy-wasteful, and learn what energy efficiency means.

  7. Total Light Management

    Broader source: Energy.gov [DOE]

    Presentation covers total light management, and is given at the Spring 2010 Federal Utility Partnership Working Group (FUPWG) meeting in Providence, Rhode Island.

  8. Lighting Technology Panel

    Broader source: Energy.gov [DOE]

    Presentation covers the Lighting Technology Panel for the Federal Utility Partnership Working Group (FUPWG) meeting, held on November 18-19, 2009. 

  9. Hybrid Solar Lighting

    SciTech Connect (OSTI)

    Maxey, L Curt [ORNL

    2008-01-01T23:59:59.000Z

    Hybrid solar lighting systems focus highly concentrated sunlight into a fiber optic bundle to provide sunlight in rooms without windows or conventional skylights.

  10. Solid-State Lighting

    Broader source: Energy.gov (indexed) [DOE]

    into the market. On the market side, DOE works closely with drivers, heat sinks, and optics. LEDs must be carefully energy efficiency program partners, lighting professionals,...

  11. Coking Coal Import Costs - EIA

    Gasoline and Diesel Fuel Update (EIA)

    Import Costs for Selected Countries U.S. Dollars per Metric Ton1 (Average Unit Value, CIF2) Country 2001 2002 2003 2004 2005 2006 2007 2008 2009 Belgium 48.67 46.59 49.25 78.98...

  12. Relating productivity to visibility and lighting

    SciTech Connect (OSTI)

    Clear, R.; Berman, S.

    1982-01-01T23:59:59.000Z

    The problem of determining the appropriate light levels for visual tasks is a cost-benefit problem. Existing light level recommendations seriously underweight the importance of economic factors. Furthermore, the relative importance of the visibility factors in determining the optimal light levels appears inconsistent with the importance of these factors in determining visibility and visual performance. It is shown that calculations based on acuities give a lower limit of 100 to 200 lux for cost-effective light levels for office tasks. Upper limits are calculated from correlations of task performance to visibility levels. Visibility levels become progressively insensitive to luminance as luminance increases. Average power densities above 100 watts/m/sup 2/ are cost-effective only when visibility is very low. However, there is a 3-to-10 times larger increase in benefits from improving contrast or contrast sensitivity than from using more than 10 watts/m/sup 2/. Contrast or contrast sensitivity can be improved by using forms with larger print, using xerographic copy instead of carbon or mimeo, making sure office workers have the right eyeglasses, or even by transferring workers with visual problems to less visually demanding tasks. Once these changes are made it is no longer cost-effective to use more than 10 watts/m/sup 2/. This conclusion raises serious questions about recommendations that lead to greater than about 10 watts/m/sup 2/ of installed lighting for general office work.

  13. Resonant Visible Light Modulation with Graphene

    E-Print Network [OSTI]

    Yu, Renwen; de Abajo, F Javier Garcia

    2015-01-01T23:59:59.000Z

    Fast modulation and switching of light at visible and near-infrared (vis-NIR) frequencies is of utmost importance for optical signal processing and sensing technologies. No fundamental limit appears to prevent us from designing wavelength-sized devices capable of controlling the light phase and intensity at gigaherts (and even terahertz) speeds in those spectral ranges. However, this problem remains largely unsolved, despite recent advances in the use of quantum wells and phase-change materials for that purpose. Here, we explore an alternative solution based upon the remarkable electro-optical properties of graphene. In particular, we predict unity-order changes in the transmission and absorption of vis-NIR light produced upon electrical doping of graphene sheets coupled to realistically engineered optical cavities. The light intensity is enhanced at the graphene plane, and so is its absorption, which can be switched and modulated via Pauli blocking through varying the level of doping. Specifically, we explor...

  14. Reducing home lighting expenses

    SciTech Connect (OSTI)

    Aimone, M.A.

    1981-02-01T23:59:59.000Z

    Ways to reduce lighting expenses are summarized. These include: turning off lights when not in use; keeping fixtures and lamps clean; replacing lamps with more efficient types; using three-way bulbs; use of daylighting; buying fewer lamps and reducing lamp wattage; consider repainting rooms; replacing recessed fixtures with tracklighting; and using efficient lamps for outdoor use. (MCW)

  15. Explosively pumped laser light

    DOE Patents [OSTI]

    Piltch, Martin S. (Los Alamos, NM); Michelotti, Roy A. (Los Alamos, NM)

    1991-01-01T23:59:59.000Z

    A single shot laser pumped by detonation of an explosive in a shell casing. The shock wave from detonation of the explosive causes a rare gas to luminesce. The high intensity light from the gas enters a lasing medium, which thereafter outputs a pulse of laser light to disable optical sensors and personnel.

  16. Light intensity compressor

    DOE Patents [OSTI]

    Rushford, Michael C. (Livermore, CA)

    1990-01-01T23:59:59.000Z

    In a system for recording images having vastly differing light intensities over the face of the image, a light intensity compressor is provided that utilizes the properties of twisted nematic liquid crystals to compress the image intensity. A photoconductor or photodiode material that is responsive to the wavelength of radiation being recorded is placed adjacent a layer of twisted nematic liquid crystal material. An electric potential applied to a pair of electrodes that are disposed outside of the liquid crystal/photoconductor arrangement to provide an electric field in the vicinity of the liquid crystal material. The electrodes are substantially transparent to the form of radiation being recorded. A pair of crossed polarizers are provided on opposite sides of the liquid crystal. The front polarizer linearly polarizes the light, while the back polarizer cooperates with the front polarizer and the liquid crystal material to compress the intensity of a viewed scene. Light incident upon the intensity compressor activates the photoconductor in proportion to the intensity of the light, thereby varying the field applied to the liquid crystal. The increased field causes the liquid crystal to have less of a twisting effect on the incident linearly polarized light, which will cause an increased percentage of the light to be absorbed by the back polarizer. The intensity of an image may be compressed by forming an image on the light intensity compressor.

  17. Lighting affects appearance LightSource emits photons

    E-Print Network [OSTI]

    Jacobs, David

    1 Lighting affects appearance #12;2 LightSource emits photons Photons travel in a straight line). And then some reach the eye/camera. #12;3 Reflectance Model how objects reflect light. Model light sources Algorithms for computing Shading: computing intensities within polygons Determine what light strikes what

  18. VIRTUAL LIGHT: DIGITALLY-GENERATED LIGHTING FOR VIDEO CONFERENCING APPLICATIONS

    E-Print Network [OSTI]

    Fisher, Kathleen

    VIRTUAL LIGHT: DIGITALLY-GENERATED LIGHTING FOR VIDEO CONFERENCING APPLICATIONS Andrea Basso method to improve the lighting conditions of a real scene or video sequence. In particular we concentrate on modifying real light sources intensities and inserting virtual lights into a real scene viewed from a fixed

  19. Commercialization of gallium nitride nanorod arrays on silicon for solid-state lighting

    E-Print Network [OSTI]

    Wee, Qixun

    2008-01-01T23:59:59.000Z

    One important component in energy usage is lighting, which is currently dominated by incandescent and fluorescent lamps. However, due to potentially higher efficiencies and thus higher energy savings, solid-state lighting ...

  20. Side-by-Side Testing of Commercial Office Lighting Systems: Two-lamp Fluorescent Fixtures

    E-Print Network [OSTI]

    Parker, D. S.; Schrum, L.; Sonne, J. K.; Stedman, T. C.

    1996-01-01T23:59:59.000Z

    Lighting systems in commercial office buildings are primary determinants of building energy use. In warmer climates, lighting energy use has important implications for building cooling loads as well as those directly associated with illumination...

  1. Important material considerations in INTOR

    SciTech Connect (OSTI)

    Abdou, M.A.; Mattas, R.F.; Smith, D.L.

    1981-01-01T23:59:59.000Z

    A number of important material-related problems were identified and analyzed during the Phase-I study for INTOR. The first wall and divertor collector plate are subjected to severe normal and off-normal conditions. A melt layer is predicted to develop in a bare stainless steel wall under plasma disruptions. Graphite tiles will not melt but they introduce other serious uncertainties into the design. The design strategy for the divertor collector plate focused on separating the surface and high heat flux problems and on utilizing a novel mechanical design concept for attaching tungsten tiles to a stainless steel (or copper) heat sink.

  2. Important Trinity / NERSC-8 Documents

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of Science (SC) EnvironmentalGyroSolé(tm)HydrogenRFP » Important Trinity / NERSC-8 Documents

  3. Effect of E85 on RCCI Performance and Emissions on a Multi-Cylinder Light-Duty Diesel Engine - SAE World Congress

    SciTech Connect (OSTI)

    Curran, Scott [ORNL; Hanson, Reed M [ORNL; Wagner, Robert M [ORNL

    2012-01-01T23:59:59.000Z

    This paper investigates the effect of E85 on load expansion and FTP modal point emissions indices under reactivity controlled compression ignition (RCCI) operation on a light-duty multi-cylinder diesel engine. A General Motors (GM) 1.9L four-cylinder diesel engine with the stock compression ratio of 17.5:1, common rail diesel injection system, high-pressure exhaust gas recirculation (EGR) system and variable geometry turbocharger was modified to allow for port fuel injection with gasoline or E85. Controlling the fuel reactivity in-cylinder by the adjustment of the ratio of premixed low-reactivity fuel (gasoline or E85) to direct injected high reactivity fuel (diesel fuel) has been shown to extend the operating range of high-efficiency clean combustion (HECC) compared to the use of a single fuel alone as in homogeneous charge compression ignition (HCCI) or premixed charge compression ignition (PCCI). The effect of E85 on the Ad-hoc federal test procedure (FTP) modal points is explored along with the effect of load expansion through the light-duty diesel speed operating range. The Ad-hoc FTP modal points of 1500 rpm, 1.0bar brake mean effective pressure (BMEP); 1500rpm, 2.6bar BMEP; 2000rpm, 2.0bar BMEP; 2300rpm, 4.2bar BMEP; and 2600rpm, 8.8bar BMEP were explored. Previous results with 96 RON unleaded test gasoline (UTG-96) and ultra-low sulfur diesel (ULSD) showed that with stock hardware, the 2600rpm, 8.8bar BMEP modal point was not obtainable due to excessive cylinder pressure rise rate and unstable combustion both with and without the use of EGR. Brake thermal efficiency and emissions performance of RCCI operation with E85 and ULSD is explored and compared against conventional diesel combustion (CDC) and RCCI operation with UTG 96 and ULSD.

  4. Unexplored Aspect of Velocity of light

    E-Print Network [OSTI]

    Abhijit Biswas; Krishnan RS Mani

    2008-05-13T23:59:59.000Z

    In the post-Maxwellian era, sensing that the tide of discoveries in electromagnetim indicated a decline of the mechanical view, Einstein replaced Newton's three absolutes -- space, time and mass, with a single one, the velocity of light. The magnitude of the velocity of light was first determined and proven to be finite independently by Ole Romer and Bradley in the eighteenth century. In the nineteenth century, Fizeau carried out the first successful measurement of the speed of light using an earthbound apparatus. Thereafter, many earthbound experiments were conducted for its determination till 1983, when its magnitude was frozen at a fixed value after it was determined up to an accuracy level of a fraction of a meter per second. Einstein considered the speed of light derived from terrestrial experiments, to be the limiting speed of all natural phenomena. Einstein stated in connection with his general relativity theory that light rays could curve only when the velocity of propagation of light varies with position. Experiments have been conducted to prove the phenomenon of light deflection to higher and higher accuracy levels, but none so far to determine the speed of light at locations closer to the sun. To verify some essential aspects of general relativity, NASA had commendably planned many costly experiments. Hence, NASA can now be expected to expeditiously plan and execute the low cost experiment proposed here, so as to conclusively verify the effect of the solar gravitational field on the speed of light, as regards the important predictions of Einstein's theory of gravitation and of its remodeled form -- the Remodeled Relativity Theory, which retained and incorporated only experimentally proven concepts and principles.

  5. Neutrino physics today, important issues and the future

    SciTech Connect (OSTI)

    Parke, Stephen J.; /Fermilab

    2010-10-01T23:59:59.000Z

    The status and the most important issues in neutrino physics will be summarized as well as how the current, pressing questions will be addressed by future experiments. Since the discovery of neutrino flavor transitions by the SuperKamiokande experiment in 1998, which demonstrates that neutrinos change and hence their clocks tick, i.e. they are not traveling at the speed of light and hence are not massless, the field of neutrino physics has made remarkable progress in untangling the nature of the neutrino. However, there are still many important questions to answer.

  6. IMPORTANCE OF SAFETY CULTURE ASSESSMENT

    SciTech Connect (OSTI)

    Spitalnik, J.

    2004-10-06T23:59:59.000Z

    Safety Management has lately been considered by some Nuclear Regulatory agencies as the tool on which to concentrate their efforts to implement modern regulation structures, because Safety Culture was said to be difficult to monitor. However, Safety Culture can be assessed and monitored even if it is problematical to make Safety Culture the object of regulation. This paper stresses the feasibility and importance of Safety Culture Assessment based on self-assessment applications performed in several nuclear organizations in Latin America. Reasons and ownership for assessing Safety Culture are discussed, and relevant aspects considered for setting up and programming such an assessment are shown. Basic principles that were taken into account, as well as financial and human resources used in actual self-assessments are reviewed, including the importance of adequate statistical analyses and the necessity of proper feed-back of results. The setting up of action plans to enhance Safety Culture is the final step of the assessment program that once implemented will enable to establish a Safety Culture monitoring process within the organization.

  7. Lakeview Light and Power- Commercial Lighting Rebate Program

    Broader source: Energy.gov [DOE]

    Lakeview Light and Power offers a commercial lighting rebate program. Rebates apply to the installation of energy efficient lighting retrofits in non-residential buildings. The rebate program is...

  8. Green Light Pulse Oximeter

    DOE Patents [OSTI]

    Scharf, John Edward (Oldsmar, FL)

    1998-11-03T23:59:59.000Z

    A reflectance pulse oximeter that determines oxygen saturation of hemoglobin using two sources of electromagnetic radiation in the green optical region, which provides the maximum reflectance pulsation spectrum. The use of green light allows placement of an oximetry probe at central body sites (e.g., wrist, thigh, abdomen, forehead, scalp, and back). Preferably, the two green light sources alternately emit light at 560 nm and 577 nm, respectively, which gives the biggest difference in hemoglobin extinction coefficients between deoxyhemoglobin, RHb, and oxyhemoglobin, HbO.sub.2.

  9. White light velocity interferometer

    DOE Patents [OSTI]

    Erskine, D.J.

    1999-06-08T23:59:59.000Z

    The invention is a technique that allows the use of broadband and incoherent illumination. Although denoted white light velocimetry, this principle can be applied to any wave phenomenon. For the first time, powerful, compact or inexpensive sources can be used for remote target velocimetry. These include flash and arc lamps, light from detonations, pulsed lasers, chirped frequency lasers, and lasers operating simultaneously in several wavelengths. The technique is demonstrated with white light from an incandescent source to measure a target moving at 16 m/s. 41 figs.

  10. Columbia Water and Light- HVAC and Lighting Efficiency Rebates

    Broader source: Energy.gov [DOE]

    Columbia Water and Light (CWL) offers rebates to its commercial and industrial customers for the purchase of high efficiency HVAC installations and efficient lighting. Incentives for certain...

  11. Reading Municipal Light Department- Business Lighting Rebate Program

    Broader source: Energy.gov [DOE]

    Reading Municipal Light Department (RMLD) offers incentives for non-residential customers to install energy efficient lights and sensors in existing facilities. In addition to rebates for the...

  12. Peninsula Light Company- Commercial Efficient Lighting Rebate Program

    Broader source: Energy.gov [DOE]

    Peninsula Light Company (PLC) offers a rebate program for commercial customers who wish to upgrade to energy efficient lighting. Participating customers must be served by PLC commercial service....

  13. Light Duty Combustion Research: Advanced Light-Duty Combustion...

    Broader source: Energy.gov (indexed) [DOE]

    duty Diesel Combustion Research Advanced Light-Duty Combustion Experiments Paul Miles Sandia National Laboratories Light-Duty Combustion Modeling Rolf Reitz University of Wisconsin...

  14. The Reduction of Retinal Autofluorescence Caused by Light Exposure

    E-Print Network [OSTI]

    is important because several clinical procedures (such as slit- lamp examination, fundus photography has led to the theory that light exposure plays a role in some retinal diseases including age

  15. Efficient Light Sources Today

    E-Print Network [OSTI]

    Hart, A. L.

    1982-01-01T23:59:59.000Z

    This paper reviews new lamp and lighting technology in terms of application and economic impact. Included are the latest advances in High Intensity Discharge systems, energy saving fluorescent lamps and ballasts, and the new state of the art high...

  16. Natural lighting and skylights

    E-Print Network [OSTI]

    Evans, Benjamin Hampton

    1961-01-01T23:59:59.000Z

    outlined herein, the feasibility of using scale models for studying skylights is also an established fact. The method of analysis by models can be a valuable tool to any designer who is concerned about day-lighting....

  17. National Synchrotron Light Source

    ScienceCinema (OSTI)

    None

    2010-01-08T23:59:59.000Z

    A tour of Brookhaven's National Synchrotron Light Source (NSLS). The NSLS is one of the world's most widely used scientific research facilities, hosting more than 2,500 guest researchers each year. The NSLS provides intense beams of infrared, ultraviole

  18. Light Vector Mesons

    E-Print Network [OSTI]

    Alexander Milov

    2008-12-21T23:59:59.000Z

    This article reviews the current status of experimental results obtained in the measurement of light vector mesons produced in proton-proton and heavy ion collisions at different energies. The review is focused on two phenomena related to the light vector mesons; the modification of the spectral shape in search of Chiral symmetry restoration and suppression of the meson production in heavy ion collisions. The experimental results show that the spectral shape of light vector mesons are modified compared to the parameters measured in vacuum. The nature and the magnitude of the modification depends on the energy density of the media in which they are produced. The suppression patterns of light vector mesons are different from the measurements of other mesons and baryons. The mechanisms responsible for the suppression of the mesons are not yet understood. Systematic comparison of existing experimental results points to the missing data which may help to resolve the problem.

  19. Light and Plants Plants use light to photosynthesize. Name two places that light can come from

    E-Print Network [OSTI]

    Koptur, Suzanne

    Light and Plants Plants use light to photosynthesize. Name two places that light can come from: 1 (CO2, a gas) from the air and turn it into SUGARS (food). This process is powered by energy from light plants) for energy. Photosynthetically Active Radiation (PAR) is a combination of red light and blue

  20. Natural gas imports and exports. Second quarter report 1995

    SciTech Connect (OSTI)

    NONE

    1995-12-31T23:59:59.000Z

    This quarter`s feature report focuses on natural gas exports to Mexico. OFP invites ideas from the public on future topics dealing with North American natural gas import/export trade. Such suggestions should be left on OFP`s electronic bulletin board. Natural Gas exports to Mexico continued to grow and reached an historic high for the month of June (7.8 Bcf). Two new long-term contracts were activated; Pennsylvania Gas & Water Company began importing 14.7 MMcf per day from TransCanada PipeLines Ltd., and Renaissance Energy (U.S.) Inc. began importing 2.8 MMcf per day from Renaissance Energy Ltd. for resale to Delmarva Power & Light Company. Algerian LNG imports remained stagnant with only one tanker being imported by Pan National Gas Sales, Inc. (Pan National). During the first six months of 1995, data indicates gas imports increased by about 10 percent over the 1994 level (1,418 vs. 1,285 Bcf), with Canadian imports increasing by 14 percent and Algerian imports decreasing by 81 percent. During the same time period, exports increased by 18 percent (83 vs. 70.1 Bcf).

  1. Light and Energy -Daylight measurements

    E-Print Network [OSTI]

    Light and Energy - Daylight measurements #12;Light and Energy - Daylight measurements Authors: Jens;3 Title Light and Energy Subtitle Daylight measurements Authors Jens Christoffersen, Ásta Logadóttir ........................................................................................................ 5 Daylight quantity

  2. Light as a Healing Mechanism

    E-Print Network [OSTI]

    Lingampalli, Nithya

    2013-01-01T23:59:59.000Z

    S. (1991). Meridians conduct light. Moskow: Raum and Zeit.the bod’ys absorption of light. Explore, 9(2), doi: https://01). The healing use of light and color. Health Care Design

  3. Solid state lighting component

    DOE Patents [OSTI]

    Yuan, Thomas; Keller, Bernd; Ibbetson, James; Tarsa, Eric; Negley, Gerald

    2010-10-26T23:59:59.000Z

    An LED component comprising an array of LED chips mounted on a planar surface of a submount with the LED chips capable of emitting light in response to an electrical signal. The LED chips comprise respective groups emitting at different colors of light, with each of the groups interconnected in a series circuit. A lens is included over the LED chips. Other embodiments can comprise thermal spreading structures included integral to the submount and arranged to dissipate heat from the LED chips.

  4. Solid state lighting component

    DOE Patents [OSTI]

    Keller, Bernd; Ibbetson, James; Tarsa, Eric; Negley, Gerald; Yuan, Thomas

    2012-07-10T23:59:59.000Z

    An LED component comprising an array of LED chips mounted on a planar surface of a submount with the LED chips capable of emitting light in response to an electrical signal. The LED chips comprise respective groups emitting at different colors of light, with each of the groups interconnected in a series circuit. A lens is included over the LED chips. Other embodiments can comprise thermal spreading structures included integral to the submount and arranged to dissipate heat from the LED chips.

  5. July 18, 2012 Using QECBs for Street Lighting Upgrades

    E-Print Network [OSTI]

    lighting technologies (e.g. light-emitting diodes, induction lighting) can reduce street light energy

  6. Threading plasmonic nanoparticle strings with light

    E-Print Network [OSTI]

    Herrmann, Lars O.; Valev, Ventsislav K.; Tserkezis, Christos; Barnard, Jonathan S.; Kasera, Setu; Scherman, Oren A.; Aizpurua, Javier; Baumberg, Jeremy J.

    2014-07-28T23:59:59.000Z

    by light induces large-scale threading, probed here across ml volumes (as depicted in Fig. 1b). Threads formed using unfocussed 805 nm, 200 fs, ultrafast laser pulses of 90MWcm#2; 2 intensity are directly seen in transmission electron microscopy (TEM... for this laser-induced assembly. Important factors for assembling nanomaterials with light. In our experiments, threading is achieved with high peak power (Ppeak) ultrafast laser pulses, which indicates that the process is non-thermal. In a non-thermal process...

  7. Sandia National Laboratories: White Light Creation Architectures

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Light Creation Architectures White Light Creation Architectures Overview of SSL White Light Creation Architectures The entire spectral range of visible light can be...

  8. Sandia National Laboratories: Lighting Developments to 2030

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    ClimateLighting Developments to 2030 Lighting Developments to 2030 videobanner Lighting Technologies, Costs, and Energy Demand: Global Developments to 2030 V iew Slides: Lighting...

  9. Generation and manipulation of nonclassical light using photonic crystals

    E-Print Network [OSTI]

    Jelena Vuckovic; Dirk Englund; David Fattal; Edo Waks; Yoshihisa Yamamoto

    2005-10-07T23:59:59.000Z

    Photonic crystal cavities can localize light into nanoscale volumes with high quality factors. This permits a strong interaction between light and matter, which is important for the construction of classical light sources with improved properties (e.g., low threshold lasers) and of nonclassical light sources (such as single and entangled photon sources) that are crucial pieces of hardware of quantum information processing systems. This article will review some of our recent experimental and theoretical results on the interaction between single quantum dots and photonic crystal cavity fields, and on the integration of multiple photonic crystal devices into functional circuits for quantum information processing.

  10. The 4th Generation Light Source at Jefferson Lab

    SciTech Connect (OSTI)

    Stephen Benson; George Biallas; James Boyce; Donald Bullard; James Coleman; David Douglas; H. Dylla; Richard Evans; Pavel Evtushenko; Albert Grippo; Christopher Gould; Joseph Gubeli; David Hardy; Carlos Hernandez-Garcia; Kevin Jordan; John Klopf; Steven Moore; George Neil; Thomas Powers; Joseph Preble; Daniel Sexton; Michelle D. Shinn; Christopher Tennant; Richard Walker; Shukui Zhang; Gwyn Williams

    2007-04-25T23:59:59.000Z

    A number of "Grand Challenges" in Science have recently been identified in reports from The National Academy of Sciences, and the U.S. Dept. of Energy, Basic Energy Sciences. Many of these require a new generation of linac-based light source to study dynamical and non-linear phenomena in nanoscale samples. In this paper we present a summary of the properties of such light sources, comparing them with existing sources, and then describing in more detail a specific source at Jefferson Lab. Importantly, the JLab light source has developed some novel technology which is a critical enabler for other new light sources.

  11. Interior Light Level Measurements Appendix F -Interior Light Level Measurements

    E-Print Network [OSTI]

    Appendix F ­ Interior Light Level Measurements #12;F.1 Appendix F - Interior Light Level. A potential concern is that a lower VT glazing may increase electric lighting use to compensate for lost qualify and quantify a representative loss of daylighting, and therefore electric lighting use

  12. Quasi light fields: extending the light field to coherent radiation

    E-Print Network [OSTI]

    Wornell, Gregory W.

    Quasi light fields: extending the light field to coherent radiation Anthony Accardi1,2 and Gregory light field, and for coherent radiation using electromagnetic field theory. We present a model of coherent image formation that strikes a balance between the utility of the light field

  13. Lighting affects appearance LightSource emits photons

    E-Print Network [OSTI]

    Jacobs, David

    1 Lighting affects appearance #12;2 LightSource emits photons Photons travel in a straight line). And then some reach the eye/camera. #12;3 Basic fact: Light is linear Double intensity of sources, double photons reaching eye. Turn on two lights, and photons reaching eye are same as sum of number when each

  14. Smart Lighting: A Second Wave in Solid State Lighting?

    E-Print Network [OSTI]

    Salama, Khaled

    Smart Lighting: A Second Wave in Solid State Lighting? OIDA Conference on Green Photonics Bob Karlicek Director, Smart Lighting Engineering Research Center Rensselaer Polytechnic Institute June 2010 #12;2 Outline · The First Wave of Solid State Lighting · Complex Dynamics in the Supply Chain · What

  15. Improved TPB-coated Light Guides for Liquid Argon TPC Light Detection Systems

    E-Print Network [OSTI]

    Z. Moss; L. Bugel; G. Collin; J. M. Conrad; B. J. P. Jones; J. Moon; M. Toups; T. Wongjirad

    2015-03-25T23:59:59.000Z

    Scintillation light produced in liquid argon (LAr) must be shifted from 128 nm to visible wavelengths in light detection systems used for liquid argon time-projection chambers (LArTPCs). To date, LArTPC light collection systems have employed tetraphenyl butadiene (TPB) coatings on photomultiplier tubes (PMTs) or plates placed in front of the PMTs. Recently, a new approach using TPB-coated light guides was proposed. In this paper, we report on light guides with improved attenuation lengths above 100 cm when measured in air. This is an important step in the development of meter-scale light guides for future LArTPCs. Improvements come from using a new acrylic-based coating, diamond-polished cast UV transmitting acrylic bars, and a hand-dipping technique to coat the bars. We discuss a model for connecting bar response in air to response in liquid argon and compare this to data taken in liquid argon. The good agreement between the prediction of the model and the measured response in liquid argon demonstrates that characterization in air is sufficient for quality control of bar production. This model can be used in simulations of light guides for future experiments.

  16. Sneaky light stop

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Eifert, Till; Nachman, Benjamin

    2015-04-01T23:59:59.000Z

    A light supersymmetric top quark partner (stop) with a mass nearly degenerate with that of the standard model (SM) top quark can evade direct searches. The precise measurement of SM top properties such as the cross-section has been suggested to give a handle for this ‘stealth stop’ scenario. We present an estimate of the potential impact a light stop may have on top quark mass measurements. The results indicate that certain light stop models may induce a bias of up to a few GeV, and that this effect can hide the shift in, and hence sensitivity from, cross-section measurements. Duemore »to the different initial states, the size of the bias is slightly different between the LHC and the Tevatron. The studies make some simplifying assumptions for the top quark measurement technique, and are based on truth-level samples.« less

  17. Pupillary efficient lighting system

    DOE Patents [OSTI]

    Berman, Samuel M. (San Francisco, CA); Jewett, Don L. (Mill Valley, CA)

    1991-01-01T23:59:59.000Z

    A lighting system having at least two independent lighting subsystems each with a different ratio of scotopic illumination to photopic illumination. The radiant energy in the visible region of the spectrum of the lighting subsystems can be adjusted relative to each other so that the total scotopic illumination of the combined system and the total photopic illumination of the combined system can be varied independently. The dilation or contraction of the pupil of an eye is controlled by the level of scotopic illumination and because the scotopic and photopic illumination can be separately controlled, the system allows the pupil size to be varied independently of the level of photopic illumination. Hence, the vision process can be improved for a given level of photopic illumination.

  18. Light emitting ceramic device

    DOE Patents [OSTI]

    Valentine, Paul; Edwards, Doreen D.; Walker, Jr., William John; Slack, Lyle H.; Brown, Wayne Douglas; Osborne, Cathy; Norton, Michael; Begley, Richard

    2010-05-18T23:59:59.000Z

    A light-emitting ceramic based panel, hereafter termed "electroceramescent" panel, is herein claimed. The electroceramescent panel is formed on a substrate providing mechanical support as well as serving as the base electrode for the device. One or more semiconductive ceramic layers directly overlay the substrate, and electrical conductivity and ionic diffusion are controlled. Light emitting regions overlay the semiconductive ceramic layers, and said regions consist sequentially of a layer of a ceramic insulation layer and an electroluminescent layer, comprised of doped phosphors or the equivalent. One or more conductive top electrode layers having optically transmissive areas overlay the light emitting regions, and a multi-layered top barrier cover comprising one or more optically transmissive non-combustible insulation layers overlay said top electrode regions.

  19. Light harvesting arrays

    DOE Patents [OSTI]

    Lindsey, Jonathan S. (Raleigh, NC)

    2002-01-01T23:59:59.000Z

    A light harvesting array useful for the manufacture of devices such as solar cells comprises: (a) a first substrate comprising a first electrode; and (b) a layer of light harvesting rods electrically coupled to the first electrode, each of the light harvesting rods comprising a polymer of Formula I: X.sup.1.paren open-st.X.sup.m+1).sub.m (I) wherein m is at least 1, and may be from two, three or four to 20 or more; X.sup.1 is a charge separation group (and preferably a porphyrinic macrocycle, which may be one ligand of a double-decker sandwich compound) having an excited-state of energy equal to or lower than that of X.sup.2, and X.sup.2 through X.sup.m+1 are chromophores (and again are preferably porphyrinic macrocycles).

  20. Renewable Energy Laboratory for Lighting Systems

    E-Print Network [OSTI]

    Dumitru Cristian; Gligor Adrian

    2010-02-23T23:59:59.000Z

    Nowadays, the electric lighting is an important part of our lives and also represents a significant part of the electric power consumption. Alternative solutions such as renewable energy applied in this domain are thus welcomed. This paper presents a workstation conceived for the study of photovoltaic solar energy for lighting systems by students of power engineering and civil engineering faculty. The proposed system is realized to study the generated photovoltaic solar energy parameters for lighting systems. For an easier way to study the most relevant parameters virtual instrumentation is implemented. National Instruments LabWindows CVI environment is used as a platform for virtual instrumentation. For future developments remote communication feature intends to be added on which currently remote monitoring of solar photovoltaic energy and electric energy parameters are monitored.

  1. Big Crunch-based omnidirectional light concentrators

    E-Print Network [OSTI]

    Igor I. Smolyaninov; Yu-Ju Hung

    2014-05-16T23:59:59.000Z

    Omnidirectional light concentration remains an unsolved problem despite such important practical applications as design of efficient mobile photovoltaic cells. Optical black hole designs developed recently offer partial solution to this problem. However, even these solutions are not truly omnidirectional since they do not exhibit a horizon, and at large enough incidence angles light may be trapped into quasi-stationary orbits around such imperfect optical black holes. Here we propose and realize experimentally another gravity-inspired design of a broadband omnidirectional light concentrator based on the cosmological Big Crunch solutions. By mimicking the Big Crunch spacetime via corresponding effective optical metric we make sure that every photon world line terminates in a single point.

  2. Spin-orbit interactions of light

    E-Print Network [OSTI]

    Bliokh, K Y; Nori, F; Zayats, A V

    2015-01-01T23:59:59.000Z

    Light carries spin and orbital angular momentum. These dynamical properties are determined by the polarization and spatial degrees of freedom of light. Modern nano-optics, photonics, and plasmonics, tend to explore subwavelength scales and additional degrees of freedom of structured, i.e., spatially-inhomogeneous, optical fields. In such fields, spin and orbital properties become strongly coupled with each other. We overview the fundamental origins and important applications of the main spin-orbit interaction phenomena in optics. These include: spin-Hall effects in inhomogeneous media and at optical interfaces, spin-dependent effects in nonparaxial (focused or scattered) fields, spin-controlled shaping of light using anisotropic structured interfaces (metasurfaces), as well as robust spin-directional coupling via evanescent near fields. We show that spin-orbit interactions are inherent in all basic optical processes, and they play a crucial role at subwavelength scales and structures in modern optics.

  3. MANDATORY MEASURES INDOOR LIGHTING CONTROLS

    E-Print Network [OSTI]

    California at Davis, University of

    MANDATORY MEASURES INDOOR LIGHTING CONTROLS (Reference: Sub-Chapter 4, Section 130.1) #12;SECTION 4 MANDATORY LIGHTING CONTROLS 1. 130.1 (a) Area Controls: Manual controls that control lighting in each area separately 2. 130.1 (b) Multi-level Controls: Allow occupants to choose the appropriate light level for each

  4. MANDATORY MEASURES INDOOR LIGHTING CONTROLS

    E-Print Network [OSTI]

    California at Davis, University of

    MANDATORY MEASURES INDOOR LIGHTING CONTROLS (Reference: Sub-Chapter 4, Section 130.1) #12;SECTION 3 MANDATORY LIGHTING CONTROLS 1. 130.1 (a) Area Controls: Manual controls that control lighting in each area separately 2. 130.1 (b) Multi-level Controls: "Dimmability." Allow occupants to choose the appropriate light

  5. MANDATORY MEASURES INDOOR LIGHTING CONTROLS

    E-Print Network [OSTI]

    California at Davis, University of

    MANDATORY MEASURES INDOOR LIGHTING CONTROLS (Reference: Sub-Chapter 4, Section 130.1) #12;SECTION 5 MANDATORY LIGHTING CONTROLS 1. Area Controls: Manual controls that control lighting in each area separately 2. Multi-level Controls: Allow occupants to choose the appropriate light level for each area 3. Shut

  6. LIGHTING 101 1. Common terminology

    E-Print Network [OSTI]

    California at Davis, University of

    SECTION 3 LIGHTING 101 1. Common terminology 2. Sources & luminaires 3. Controls #12;SECTION 3SECTION 3 DISCUSSION: COMMON LIGHTING TERMINOLOGY 1. What are the definitions of the following lighting terms? 2. Do you use these terms in professional practice? 3. What other lighting terminology do you use

  7. LIGHTING 101 1. Common terminology

    E-Print Network [OSTI]

    California at Davis, University of

    LIGHTING 101 1. Common terminology 2. Sources and luminaires 3. Controls #12;SECTION 2 DISCUSSION: COMMON LIGHTING TERMINOLOGY 1. What are the definitions of the following lighting terms? 2. Do you use these terms in professional practice? 3. What other lighting terminology do you use on the job? SLIDE 14

  8. Radioluminescent lighting technology

    SciTech Connect (OSTI)

    Not Available

    1990-01-01T23:59:59.000Z

    The glow-in-the-dark stereotype that characterizes the popular image of nuclear materials is not accidental. When the French scientist, Henri Becquerel, first discovered radioactivity in 1896, he was interested in luminescence. Radioluminescence, the production of light from a mixture of energetic and passive materials, is probably the oldest practical application of the unstable nucleus. Tritium-based radioluminescent lighting, in spite of the biologically favorable character of the gaseous tritium isotope, was included in the general tightening of environmental and safety regulations. Tritium light manufacturers would have to meet two fundamental conditions: (1) The benefit clearly outweighed the risk, to the extent that even the perceived risk of a skeptical public would be overcome. (2) The need was significant enough that the customer/user would be willing and able to afford the cost of regulation that was imposed both in the manufacture, use and eventual disposal of nuclear materials. In 1981, researchers at Oak Ridge National Laboratory were investigating larger radioluminescent applications using byproduct nuclear material such as krypton-85, as well as tritium. By 1982, it appeared that large source, (100 Curies or more) tritium gas tube, lights might be useful for marking runways and drop zones for military operations and perhaps even special civilian aviation applications. The successful development of this idea depended on making the light bright enough and demonstrating that large gas tube sources could be used and maintained safely in the environment. This successful DOE program is now in the process of being completed and closed-out. Working closely with the tritium light industry, State governments and other Federal agencies, the basic program goals have been achieved. This is a detailed report of what they have learned, proven, and discovered. 91 refs., 29 figs., 5 tabs. (JF)

  9. Sustainable LED Fluorescent Light Replacement Technology

    SciTech Connect (OSTI)

    None

    2011-06-30T23:59:59.000Z

    Ilumisys and the National Center for Manufacturing Sciences (NCMS) partnered on a three-year project awarded by the United States (U.S.) Department of Energy (DOE), to quantify the impacts of LED lamps, incandescent lamps and fluorescent benchmark lamps over a product lifecycle – i.e. to develop a sustainable design and manufacturing strategy that addresses product manufacturing, use, recycling and disposal scenarios for LED-based lighting. Based on the knowledge gained from extensive product tear-down studies of fluorescent and screw-in lighting products, lifecycle assessment tools, and accelerated lifecycle testing protocols, an interactive Sustainable LED Design Guide has been developed to aid architectural and lighting designers and engineers in making design decisions that consider three important environmental impacts (greenhouse gas emissions, energy use and mercury emission) across all phases of the life of an LED lighting product. Critical information developed for the lifecycle analysis and product feature comparisons is the useful life of the lighting product as well as its performance. The Design Guide is available at www.ncms.org, and was developed based on operational and durability testing of a variety of lighting products including power consumption, light output, and useful life of a lamp in order to allow a more realistic comparison of lamp designs. This report describes the main project tasks, results and innovative features of the lifecycle assessment (LCA)-based design tools, and the key considerations driving the sustainable design of LED lighting systems. The Design Guide incorporates the following three novel features for efficiently evaluating LED lighting features in value-chains: • Bill-of-Materials (BOM) Builder – Designers may import process data for each component and supply functional data for the product, including power, consumption, lumen output and expected useful life. • Environmental Impact Review – Designs are comparable across lifecycle phases, subsystems, and environmental impact category, and can be normalized to a userdefined functional unit. • Drill-down Review – These provide an indepth look at individual lamp designs with the ability to review across subsystem or lifecycle phase.

  10. Evaluations of nutrient diffusing substrates and the primary importance of light in controlling periphyton

    E-Print Network [OSTI]

    Murawski, Matthew Thomas

    2001-01-01T23:59:59.000Z

    eutrophication. In the first study, artificial channels were used to investigate the response of periphyton to different nutrient delivery mechanisms. In two channels, nutrients were delivered via diffusion to periphyton growth surfaces using modified Matlock...

  11. Evaluations of nutrient diffusing substrates and the primary importance of light in controlling periphyton 

    E-Print Network [OSTI]

    Murawski, Matthew Thomas

    2001-01-01T23:59:59.000Z

    eutrophication. In the first study, artificial channels were used to investigate the response of periphyton to different nutrient delivery mechanisms. In two channels, nutrients were delivered via diffusion to periphyton growth surfaces using modified Matlock...

  12. Lighting plasmas, energy and the environment

    SciTech Connect (OSTI)

    Rogoff, G.L. [Osram Sylvania Inc., Salem, MA (United States)

    1994-12-31T23:59:59.000Z

    Light production accounts for a significant fraction of the electrical energy used, and plasma-based light sources presently account for a significant fraction of existing lamps. In fact, the plasma-lamp portion is increasing, primarily due to the efficiency and economic benefits offered. Although relatively complex systems, the plasmas contained in those lamps are highly efficient electrical-to-radiative energy converters. Lighting can affect the environment indirectly through the power generation technologies as well as through waste disposal. However, while the relevance of energy efficiency and material disposal to environmental issues is clear, less apparent, but also important, are the environmental effects of the light itself. The latter play a significant role in determining whether lamp improvements are accepted and used. This talk describes some aspects of the physics of plasma lamps that are particularly important in establishing their widespread use. Topics include: key discharge processes, the significance of mercury in plasma-based lamps, and the disposal issue, particularly for mercury.

  13. Status Report on the Light Baryonic States

    E-Print Network [OSTI]

    B. M. K. Nefkens; J. W. Price

    2002-02-08T23:59:59.000Z

    The regularities in the spectrum of the light baryon resonances are reviewed and compared with those of the light mesons. We discuss the occurrence of parity doublets and clusters, and note the trends in the values of the masses, widths, spins, and parities. The importance of SU(3) flavor is illustrated and the status of quark model calculations of the baryonic spectrum is reviewed. The absence of evidence for baryonic hybrids is particularly interesting. We propose to use better symbols for the baryon resonances which do not conflict with the simple quark structure of QCD. We shall comment also on fine tuning the Star System for the hadronic states. The importance of greater support for the construction and operation of secondary beams of $\\pi$, $K$, $\\bar p$, $\\vec{n}$ and $\\vec\\gamma$ up to 5 GeV/$c$ for the future of non-perturbative QCD is emphasized.

  14. AIRPORT LIGHTING Session Highlights

    E-Print Network [OSTI]

    Minnesota, University of

    Administration advisory circulars, available online at www.faa.gov or by mail at the following address: Federal Aviation Administration, Airports 800 Independence Ave. S.W. Washington, D.C. 20591 To qualify for federal AND NAVIGATIONAL AIDS A complete list of federal regulations for airfield lighting is located in Federal Aviation

  15. Tokyo Street Lights

    E-Print Network [OSTI]

    Hacker, Randi; Tsutsui, William

    2008-03-12T23:59:59.000Z

    that you have only 17, no 16, no 15 seconds left to get to the other side before the light changes and the impatient American drivers put the pedal to the metal and it's road kill time. Talk about stress! In Tokyo, crossing the street is a leisurely...

  16. Sweetness and light 

    E-Print Network [OSTI]

    Craig, Katie

    2014-07-03T23:59:59.000Z

    1. Sweetness and Light. A novel. Judi lives in a nice, clean house with her seventeen year old stepson, who won’t talk to her in anything but monosyllables. His father, Nelson, and she are struggling to relate to each ...

  17. Amending Default Outdoor Lighting Zones by Local Jurisdictions Having Authority (AHJ)

    E-Print Network [OSTI]

    Amending Default Outdoor Lighting Zones by Local Jurisdictions Having Authority (AHJ) An important part of the Standards is to base the outdoor lighting power that is allowed on how bright the surrounding conditions are. The Standards contain lighting power allowances` for newly installed equipment

  18. Light-Tightness Quality Check for Curtis Schmidt 8-inch Shutters Tyler W. Behm,1,

    E-Print Network [OSTI]

    Light-Tightness Quality Check for Curtis Schmidt 8-inch Shutters Tyler W. Behm,1, J.P. Rheault,1 light is "leaked" through a closed CCD shutter. We find that by orienting the actuator towards the CCD 1 in 250,000 at most. I. INTRODUCTION Light-tightness is an important quality in shutters. Poor

  19. Light Duty Efficient, Clean Combustion

    SciTech Connect (OSTI)

    Donald Stanton

    2010-12-31T23:59:59.000Z

    Cummins has successfully completed the Light Duty Efficient Clean Combustion (LDECC) cooperative program with DoE. This program was established in 2007 in support of the Department of Energy's Vehicles Technologies Advanced Combustion and Emissions Control initiative to remove critical barriers to the commercialization of advanced, high efficiency, emissions compliant internal combustion (IC) engines for light duty vehicles. Work in this area expanded the fundamental knowledge of engine combustion to new regimes and advanced the knowledge of fuel requirements for these diesel engines to realize their full potential. All of the following objectives were met with fuel efficiency improvement targets exceeded: (1) Improve light duty vehicle (5000 lb. test weight) fuel efficiency by 10.5% over today's state-of-the-art diesel engine on the FTP city drive cycle; (2) Develop and design an advanced combustion system plus aftertreatment system that synergistically meets Tier 2 Bin 5 NOx and PM emissions standards while demonstrating the efficiency improvements; (3) Maintain power density comparable to that of current conventional engines for the applicable vehicle class; and (4) Evaluate different fuel components and ensure combustion system compatibility with commercially available biofuels. Key accomplishments include: (1) A 25% improvement in fuel efficiency was achieved with the advanced LDECC engine equipped with a novel SCR aftertreatment system compared to the 10.5% target; (2) An 11% improvement in fuel efficiency was achieved with the advanced LDECC engine and no NOx aftertreamtent system; (3) Tier 2 Bin 5 and SFTP II emissions regulations were met with the advanced LDECC engine equipped with a novel SCR aftertreatment system; (4) Tier 2 Bin 5 emissions regulations were met with the advanced LDECC engine and no NOx aftertreatment, but SFTP II emissions regulations were not met for the US06 test cycle - Additional technical barriers exist for the no NOx aftertreatment engine; (5) Emissions and efficiency targets were reached with the use of biodiesel. A variety of biofuel feedstocks (soy, rapeseed, etc.) was investigated; (6) The advanced LDECC engine with low temperature combustion was compatible with commercially available biofuels as evaluated by engine performance testing and not durability testing; (7) The advanced LDECC engine equipped with a novel SCR aftertreatment system is the engine system architecture that is being further developed by the Cummins product development organization. Cost reduction and system robustness activities have been identified for future deployment; (8) The new engine and aftertreatment component technologies are being developed by the Cummins Component Business units (e.g. fuel system, turbomachinery, aftertreatment, electronics, etc.) to ensure commercial viability and deployment; (9) Cummins has demonstrated that the technologies developed for this program are scalable across the complete light duty engine product offerings (2.8L to 6.7L engines); and (10) Key subsystems developed include - sequential two stage turbo, combustions system for low temperature combustion, novel SCR aftertreatment system with feedback control, and high pressure common rail fuel system. An important element of the success of this project was leveraging Cummins engine component technologies. Innovation in component technology coupled with system integration is enabling Cummins to move forward with the development of high efficiency clean diesel products with a long term goal of reaching a 40% improvement in thermal efficiency for the engine plus aftertreatment system. The 40% improvement is in-line with the current light duty vehicle efficiency targets set by the 2010 DoE Vehicle Technologies MYPP and supported through co-operative projects such as the Cummins Advanced Technology Powertrains for Light-Duty Vehicles (ATP-LD) started in 2010.

  20. Light Duty Efficient, Clean Combustion

    SciTech Connect (OSTI)

    Stanton, Donald W

    2011-06-03T23:59:59.000Z

    Cummins has successfully completed the Light Duty Efficient Clean Combustion (LDECC) cooperative program with DoE. This program was established in 2007 in support of the Department of Energy’s Vehicles Technologies Advanced Combustion and Emissions Control initiative to remove critical barriers to the commercialization of advanced, high efficiency, emissions compliant internal combustion (IC) engines for light duty vehicles. Work in this area expanded the fundamental knowledge of engine combustion to new regimes and advanced the knowledge of fuel requirements for these diesel engines to realize their full potential. All of the following objectives were met with fuel efficiency improvement targets exceeded: 1. Improve light duty vehicle (5000 lb. test weight) fuel efficiency by 10.5% over today’s state-ofthe- art diesel engine on the FTP city drive cycle 2. Develop & design an advanced combustion system plus aftertreatment system that synergistically meets Tier 2 Bin 5 NOx and PM emissions standards while demonstrating the efficiency improvements. 3. Maintain power density comparable to that of current conventional engines for the applicable vehicle class. 4. Evaluate different fuel components and ensure combustion system compatibility with commercially available biofuels. Key accomplishments include: ? A 25% improvement in fuel efficiency was achieved with the advanced LDECC engine equipped with a novel SCR aftertreatment system compared to the 10.5% target ? An 11% improvement in fuel efficiency was achieved with the advanced LDECC engine and no NOx aftertreamtent system ? Tier 2 Bin 5 and SFTP II emissions regulations were met with the advanced LDECC engine equipped with a novel SCR aftertreatment system ? Tier 2 Bin 5 emissions regulations were met with the advanced LDECC engine and no NOx aftertreatment, but SFTP II emissions regulations were not met for the US06 test cycle – Additional technical barriers exist for the no NOx aftertreatment engine ? Emissions and efficiency targets were reached with the use of biodiesel. A variety of biofuel feedstocks (soy, rapeseed, etc.) was investigated. ? The advanced LDECC engine with low temperature combustion was compatible with commercially available biofuels as evaluated by engine performance testing and not durability testing. ? The advanced LDECC engine equipped with a novel SCR aftertreatment system is the engine system architecture that is being further developed by the Cummins product development organization. Cost reduction and system robustness activities have been identified for future deployment. ? The new engine and aftertreatment component technologies are being developed by the Cummins Component Business units (e.g. fuel system, turbomachinery, aftertreatment, electronics, etc.) to ensure commercial viability and deployment ? Cummins has demonstrated that the technologies developed for this program are scalable across the complete light duty engine product offerings (2.8L to 6.7L engines) ? Key subsystems developed include – sequential two stage turbo, combustions system for low temperature combustion, novel SCR aftertreatment system with feedback control, and high pressure common rail fuel system An important element of the success of this project was leveraging Cummins engine component technologies. Innovation in component technology coupled with system integration is enabling Cummins to move forward with the development of high efficiency clean diesel products with a long term goal of reaching a 40% improvement in thermal efficiency for the engine plus aftertreatment system. The 40% improvement is in-line with the current light duty vehicle efficiency targets set by the 2010 DoE Vehicle Technologies MYPP and supported through co-operative projects such as the Cummins Advanced Technology Powertrains for Light- Duty Vehicles (ATP-LD) started in 2010.

  1. Enhancing the use of coals by gas reburning-sorbent injection: Volume 3 -- Gas reburning-sorbent injection at Edwards Unit 1, Central Illinois Light Company. Final report

    SciTech Connect (OSTI)

    NONE

    1996-03-01T23:59:59.000Z

    Design work has been completed for a Gas Reburning-Sorbent Injection (GR-SI) system to reduce emissions of NO{sub x} and SO{sub 2} from a wall fired unit at Central Illinois Light Company`s Edwards Station Unit 1, located in Bartonville, Illinois. The goal of the project was to reduce emissions of NO{sub x} by 60%, from the as found baseline of 0.98 lb/MBtu and to reduce emissions of SO{sub 2} by 50%. Since the unit currently fires a blend of high sulfur Illinois coal and low sulfur Kentucky coal to meet an SO{sub 2} limit of 1.8 lb/MBtu, the goal at this site was amended to meeting this limit while increasing the fraction of high sulfur coal to 57% from the current 15% level. GR-SI requires injection of natural gas into the furnace at the level of the top burner row, creating a fuel-rich zone in which NO{sub x} formed in the coal zone is reduced to N{sub 2}. Recycled flue gas is used to increase the reburning fuel jet momentum, resulting in enhanced mixing. Recycled flue gas is also used to cool the top row of burners which would not be in service during GR operation. Dry hydrated lime sorbent is injected into the upper furnace to react with SO{sub 2}, forming solid CaSO{sub 4} and CaSO{sub 3}, which are collected by the ESP. The system was designed to inject sorbent at a rate corresponding to a calcium (sorbent) to sulfur (coal) molar ratio of 2.0. The SI system design was optimized with respect to gas temperature, injection air flow rate, and sorbent dispersion. Sorbent injection air flow is equal to 3% of the combustion air. The design includes modifications of the ESP, sootblowing, and ash handling systems.

  2. Superposed Coherent and Squeezed Light

    E-Print Network [OSTI]

    Fesseha Kassahun

    2012-01-18T23:59:59.000Z

    We first calculate the mean photon number and quadrature variance of superposed coherent and squeezed light, following a procedure of analysis based on combining the Hamiltonians and using the usual definition for the quadrature variance of superposed light beams. This procedure of analysis leads to physically unjustifiable mean photon number of the coherent light and quadrature variance of the superposed light. We then determine both of these properties employing a procedure of analysis based on superposing the Q functions and applying a slightly modified definition for the quadrature variance of a pair of superposed light beams. We find the expected mean photon number of the coherent light and the quadrature variance of the superposed light. Moreover, the quadrature squeezing of the superposed output light turns out to be equal to that of the superposed cavity light.

  3. LED Color Stability: 10 Important Questions

    Broader source: Energy.gov [DOE]

    This April 15, 2014 webinar examined the causes of color shift, and took a look at existing metrics used to describe color shift/color stability in LED lighting. The lumen maintenance lifetime of...

  4. Netherton's syndrome: the importance of eyebrow hair

    E-Print Network [OSTI]

    Boussofara, Lobna; Ghannouchi, Nadia; Ghariani, Najet; Denguezli, Mohamed; Belajouza, Colandane; Nouira, Rafia

    2007-01-01T23:59:59.000Z

    trichorrhexis nodosa – "Bamboo hairs". AMA Arch Derm. 1958of examination of eyebrow hairs by light microscopy in orderIgE and characteristic skin and hair finding. J Allergy Clin

  5. Imports and Exports of Fishery Products

    E-Print Network [OSTI]

    Imports and Exports of Fishery Products Annual Summary, 2001 IMPORTS. U.S. imports of edible of fishery products were imported. EXPORTS. U.S. exports of edible fishery products of domestic origin were 1,139,744 tons valued at $3.1 billion, compared with 948,025 tons at $2.8 billion exported in 2000

  6. IMPORTS AND EXPORTS OF FISHERY PRODUCTS

    E-Print Network [OSTI]

    IMPORTS AND EXPORTS OF FISHERY PRODUCTS ANNUAL SUMMARY, 1996 IMPORTS. U.S. imports of edible higher than in 1995, when $12.5 billion of fishery products were imported. EXPORTS. U.S. exports,376 tons at $3.1 billion exported in 1995. Fresh and frozen items were 791,822 tons valued at $2.2 billion

  7. Imports and Exports of Fishery Products

    E-Print Network [OSTI]

    Imports and Exports of Fishery Products Annual Summary, 1998 IMPORTS. U.S. imports of edible higher than in 1997, when $14.5 billion of fishery products were imported. EXPORTS. U.S. exports,499 tons at $2.6 billion exported in 1997. Fresh and frozen items were 631,627 tons valued at $1.7 billion

  8. Imports and Exports of Fishery Products

    E-Print Network [OSTI]

    Imports and Exports of Fishery Products Annual Summary, 2003 IMPORTS. U.S. imports of edible imported. EXPORTS. U.S. exports of edible fishery products of domestic origin were 1,047,706 tons valued at $3.1 billion, compared with 1,056,303 tons at $3.0 billion exported in 2002. Fresh and frozen items

  9. IMPORTS AND EXPORTS OF FISHERY PRODUCTS

    E-Print Network [OSTI]

    IMPORTS AND EXPORTS OF FISHERY PRODUCTS ANNUAL SUMMARY, 1997 IMPORTS. U.S. imports of edible higher than in 1996, when $13.1 billion of fishery products were imported. EXPORTS. U.S. exports,720 tons at $2.9 billion exported in 1996. Fresh and frozen items were 782,767 tons valued at $2.0 billion

  10. Imports and Exports of Fishery Products

    E-Print Network [OSTI]

    Imports and Exports of Fishery Products Annual Summary, 2000 IMPORTS. U.S. imports of edible.0 billion of fishery products were imported. EXPORTS. U.S. exports of edible fishery products of domestic origin were 948,025 tons valued at $2.8 billion, compared with 864,166 tons at $2.7 billion exported

  11. Imports and Exports of Fishery Products

    E-Print Network [OSTI]

    Imports and Exports of Fishery Products Annual Summary, 1999 IMPORTS. U.S. imports of edible higher than in 1998, when $15.6 billion of fishery products were imported. EXPORTS. U.S. exports,067 tons at $2.2 billion exported in 1998. Fresh and frozen items were 725,050 tons valued at $2.1 billion

  12. Heavy-light quarks interactions in QCD vacuum

    E-Print Network [OSTI]

    Mirzayusuf Musakhanov

    2015-03-20T23:59:59.000Z

    QCD vacuum instantons induce very strong interactions between light quarks, which generate large dynamical light quark mass M for initially almost massless quarks and can bound these quarks to produce almost massless pions in accordance with the spontaneous breaking of chiral symmetry (S\\chiSB). On the other hand, the QCD vacuum instantons generate heavy-light quark interactions terms, which are responsible for the effects of S\\chiSB in a heavy-light quark system. Summing the re-scattering series that lead to the total light quark propagator and making few further steps, we get the fermionized representation of low-frequencies light quark determinant in the presence of the quark sources, which is relevant for our problems. The next important step in the line of this strategy is to derive the equation and calculate the heavy quark propagator in the instanton media and in the presence of light quarks. This one provide finally the heavy and N_f light quarks interaction term. As an example, we derive heavy quark-light mesons interaction term for the N_f=2 case. If we take the average instanton size \\rho=0.35 fm, and average inter-instanton distance R=0.856 fm from our previous estimates, we obtain at LO on 1/N_c expansion dynamical light quark mass M = 570 MeV and instanton media contribution to heavy quark mass \\Delta M=148 MeV. These factors define the coupling between heavy and light quarks and, certainly, between heavy quarks and light mesons. We will apply this approach to heavy quark and heavy-light quark systems.

  13. Transformations in Lighting: The Ninth Annual Solid-State Lighting...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    in DOE's "Transformations in Lighting" Solid-State Lighting (SSL) R&D Workshop. DOE SSL Portfolio Manager James Brodrick kicked off Day 1 by observing that although LED...

  14. Integration of Self-Assembled Porous Alumina and Distributed Bragg Reflector for Light Trapping in Si Photovoltaic Devices

    E-Print Network [OSTI]

    Sheng, Xing

    Light trapping is an important issue for thin film silicon photovoltaic cells due to the limited absorption coefficient for near infrared light. In this letter, we present a photonic structure that combines porous anodic ...

  15. Light cone matrix product

    SciTech Connect (OSTI)

    Hastings, Matthew B [Los Alamos National Laboratory

    2009-01-01T23:59:59.000Z

    We show how to combine the light-cone and matrix product algorithms to simulate quantum systems far from equilibrium for long times. For the case of the XXZ spin chain at {Delta} = 0.5, we simulate to a time of {approx} 22.5. While part of the long simulation time is due to the use of the light-cone method, we also describe a modification of the infinite time-evolving bond decimation algorithm with improved numerical stability, and we describe how to incorporate symmetry into this algorithm. While statistical sampling error means that we are not yet able to make a definite statement, the behavior of the simulation at long times indicates the appearance of either 'revivals' in the order parameter as predicted by Hastings and Levitov (e-print arXiv:0806.4283) or of a distinct shoulder in the decay of the order parameter.

  16. Nonequilibrium lighting plasmas

    SciTech Connect (OSTI)

    Dakin, J.T. (GE Lighting, Nela Park, Cleveland, OH (US))

    1991-12-01T23:59:59.000Z

    In this paper the science of a variety of devices employing nonequilibrium lighting plasmas is reviewed. The devices include the fluorescent lamp, the low-pressure sodium lamp, the neon sign, ultraviolet lamps, glow indicators, and a variety of devices used by spectroscopists, such as the hollow cathode light source. The plasma conditions in representative commercial devices are described. Recent research on the electron gas, the role of heavy particles, spatial and temporal inhomogeneities, and new electrodeless excitation schemes is reviewed. Areas of future activity are expected to be in new applications of high-frequency electronics to commercial devices, new laser-based diagnostics of plasma conditions, and more sophisticated models requiring more reliable and extensive rate coefficient data.

  17. The Advanced Light Source

    SciTech Connect (OSTI)

    Jackson, A.

    1991-05-01T23:59:59.000Z

    The Advanced Light Source (ALS), a national user facility currently under construction at the Lawrence Berkeley Laboratory (LBL), is a third-generation synchrotron light source designed to produce extremely bright beams of synchrotron radiation in the energy range from a few eV to 10 keV. The design is based on a 1--1.9-GeV electron storage ring (optimized at 1.5 GeV), and utilizes special magnets, known as undulators and wigglers (collectively referred to as insertion devices), to generate the radiation. The facility is scheduled to begin operating in April 1993. In this paper we describe the progress in the design, construction, and commissioning of the accelerator systems, insertion devices, and beamlines. Companion presentations at this conference give more detail of specific components in the ALS, and describe the activities towards establishing an exciting user program. 3 figs., 2 tabs.

  18. Scattering Of Light Nuclei

    SciTech Connect (OSTI)

    Quaglioni, S; Navratil, P; Roth, R

    2009-12-15T23:59:59.000Z

    The exact treatment of nuclei starting from the constituent nucleons and the fundamental interactions among them has been a long-standing goal in nuclear physics. Above all nuclear scattering and reactions, which require the solution of the many-body quantum-mechanical problem in the continuum, represent an extraordinary theoretical as well as computational challenge for ab initio approaches.We present a new ab initio many-body approach which derives from the combination of the ab initio no-core shell model with the resonating-group method [4]. By complementing a microscopic cluster technique with the use of realistic interactions, and a microscopic and consistent description of the nucleon clusters, this approach is capable of describing simultaneously both bound and scattering states in light nuclei. We will discuss applications to neutron and proton scattering on sand light p-shell nuclei using realistic nucleon-nucleon potentials, and outline the progress toward the treatment of more complex reactions.

  19. Fusion pumped light source

    DOE Patents [OSTI]

    Pappas, Daniel S. (Los Alamos, NM)

    1989-01-01T23:59:59.000Z

    Apparatus is provided for generating energy in the form of light radiation. A fusion reactor is provided for generating a long, or continuous, pulse of high-energy neutrons. The neutron flux is coupled directly with the lasing medium. The lasing medium includes a first component selected from Group O of the periodic table of the elements and having a high inelastic scattering cross section. Gamma radiation from the inelastic scattering reactions interacts with the first component to excite the first component, which decays by photon emission at a first output wavelength. The first output wavelength may be shifted to a second output wavelength using a second liquid component responsive to the first output wavelength. The light outputs may be converted to a coherent laser output by incorporating conventional optics adjacent the laser medium.

  20. Solar light bulb

    SciTech Connect (OSTI)

    Smith, D.A.

    1983-07-26T23:59:59.000Z

    A system for generating light directly using solar energy is provided herein. It includes a concentrator and accumulator for the sun's rays to generate a concentrated beam of visible solar radiation. A distributor shaft is provided for distributing the beam of visible solar radiation. A fork is provided in the distributor shaft to define a plurality of branch lines, each provided with a mirror at the intersection to direct the beam down the respective branch line to permit parallel fractions of the beam to be reflected off the respective mirrors and to pass down the respective branch line. A solar bulb is provided including a double walled upper bulbous portion including the inlet from the branch line and a pair of heat outlet tubes, and a double walled lower bulbous portion, the upper portion thereof being divergently reflective, with the lower portion having walls which are either transparent or translucent to provide greater light diffusion, and the space between the two walls being maintained under vacuum to provide heat insulation values. A structure is provided within the solar bulb for the absorption and radiation of the concentrated beam of visible solar radiation. Preferably structure is provided connected to the solar bulb to draw in outside air in the summer to direct it past the solar bulb and to air vent hot air produced at the solar bulb to the outside, thereby providing light with minimal heat in the summer. The same structure is operated in the winter to draw in household air to direct it past the solar bulb and to recirculate such heated air produced at the solar bulb to the house, thereby providing light and heat in the winter.

  1. Turbo-Charged Lighting Design

    E-Print Network [OSTI]

    Clark, W. H. II

    TURBO-CHARGED LIGHTING DESIGN William H. Clark II Design Engineer O'Connell Robertson & Assoc Austin/ Texas ABSTRACT The task of the lighting designer has become very complex, involving thousands of choices for fixture types and hundreds...

  2. Webinar: Fuel Cell Mobile Lighting

    Broader source: Energy.gov [DOE]

    Video recording of the Fuel Cell Technologies Office webinar, Fuel Cell Mobile Lighting, originally presented on November 13, 2012.

  3. Faster than Light Quantum Communication

    E-Print Network [OSTI]

    A. Y. Shiekh

    2008-04-05T23:59:59.000Z

    Faster than light communication might be possible using the collapse of the quantum wave-function without any accompanying paradoxes.

  4. A novel coal feeder for production of low sulfur fuel. Annual technical progress report, October 1, 1990--October 1, 1991

    SciTech Connect (OSTI)

    Khang, S.J.; Lin, L.; Keener, T.C.; Yeh, P.

    1991-12-31T23:59:59.000Z

    A dual-screw feeder was designed for desulfurization of coal. This reactor contains two screw tubes, the inner tube acting as a coal pyrolizer and the outer tube acting as a desulfurizer with hot calcined lime pellets or other renewable sorbent pellets. The objectives of this project is to study the feasibility of an advanced concept of desulfurization and possibly some denitrification in this coal feeder. In this year, two basic studies have been performed: (1) the desulfurization and (2) the denitrification due to mild pyrolysis. Specifically, the following tasks have been performed: (1) Setting up the Dual-Screw reactor, (2) Determination of the pyrolysis product and the sulfur distribution in char, tar and gas based on experimental data, (3) Study of the devolatilization, the desulfurization kinetics and the denitrification kinetics and obtaining the basic kinetic parameters, (4) Study of the sulfur removal efficiency of lime pellets fed into the outer tube of the dual-feeder reactor, (5) Study of the effect of the coal particle size on pyrolysis and desulfurization, (6) Study of the coal pyrolysis and desulfurization using a TGA(Thermal Gravimetric Analyzer).

  5. MANDATORY MEASURES OUTDOOR LIGHTING CONTROLS

    E-Print Network [OSTI]

    California at Davis, University of

    MANDATORY MEASURES OUTDOOR LIGHTING CONTROLS (Reference: Sub-Chapter 4, Section 130.2) #12;SECTION level of each multi-tier garage. · General lighting must have occupant sensing controls with at least one control step between 20% and 50% of design lighting power · No more than 500 watts of rated

  6. MANDATORY MEASURES OUTDOOR LIGHTING CONTROLS

    E-Print Network [OSTI]

    California at Davis, University of

    MANDATORY MEASURES OUTDOOR LIGHTING CONTROLS (Reference: Sub-Chapter 4, Section 130.2) #12;SECTION 5 Additions and Alterations Any alteration that increases the connected lighting load must meet all No measures required OUTDOOR LIGHTING11/20/2014 #12;SECTION 5 BACKLIGHT, UPLIGHT, AND GLARE (BUG) RATINGS

  7. STATE OF CALIFORNIA RESIDENTIAL LIGHTING

    E-Print Network [OSTI]

    STATE OF CALIFORNIA RESIDENTIAL LIGHTING CEC-CF-6R-LTG-01 (Revised 08/09) CALIFORNIA ENERGY COMMISSION INSTALLATION CERTIFICATE CF-6R-LTG-01 Residential Lighting (Page 1 of 6) Site Address: Enforcement Agency: Permit Number: 2008 Residential Compliance Forms August 2009 1. Kitchen Lighting Does project

  8. Arnold Schwarzenegger, LIGHTING RESEARCH PROGRAM

    E-Print Network [OSTI]

    ;#12;Prepared By: Lighting Research Center Andrew Bierman, Project Lead Troy, New York 12180 Managed ByArnold Schwarzenegger, Governor LIGHTING RESEARCH PROGRAM PROJECT 3.2 ENERGY EFFICIENT LOAD- SHEDDING LIGHTING TECHNOLOGY Prepared For: California Energy Commission Public Interest Energy Research

  9. Slow-light solitons revisited

    E-Print Network [OSTI]

    A. V. Rybin; I. P. Vadeiko; A. R. Bishop

    2006-08-16T23:59:59.000Z

    We investigate propagation of slow-light solitons in atomic media described by the nonlinear $\\Lambda$-model. Under a physical assumption, appropriate to the slow light propagation, we reduce the $\\Lambda$-scheme to a simplified nonlinear model, which is also relevant to 2D dilatonic gravity. Exact solutions describing various regimes of stopping slow-light solitons can then be readily derived.

  10. Light-Front Holographic QCD

    SciTech Connect (OSTI)

    Brodsky, Stanley J.; /SLAC /Southern Denmark U., CP3-Origins; de Teramond, Guy F.; /Costa Rica U.

    2012-02-16T23:59:59.000Z

    The relation between the hadronic short-distance constituent quark and gluon particle limit and the long-range confining domain is yet one of the most challenging aspects of particle physics due to the strong coupling nature of Quantum Chromodynamics, the fundamental theory of the strong interactions. The central question is how one can compute hadronic properties from first principles; i.e., directly from the QCD Lagrangian. The most successful theoretical approach thus far has been to quantize QCD on discrete lattices in Euclidean space-time. Lattice numerical results follow from computation of frame-dependent moments of distributions in Euclidean space and dynamical observables in Minkowski spacetime, such as the time-like hadronic form factors, are not amenable to Euclidean lattice computations. The Dyson-Schwinger methods have led to many important insights, such as the infrared fixed point behavior of the strong coupling constant, but in practice, the analyses are limited to ladder approximation in Landau gauge. Baryon spectroscopy and the excitation dynamics of nucleon resonances encoded in the nucleon transition form factors can provide fundamental insight into the strong-coupling dynamics of QCD. New theoretical tools are thus of primary interest for the interpretation of the results expected at the new mass scale and kinematic regions accessible to the JLab 12 GeV Upgrade Project. The AdS/CFT correspondence between gravity or string theory on a higher-dimensional anti-de Sitter (AdS) space and conformal field theories in physical space-time has led to a semiclassical approximation for strongly-coupled QCD, which provides physical insights into its nonperturbative dynamics. The correspondence is holographic in the sense that it determines a duality between theories in different number of space-time dimensions. This geometric approach leads in fact to a simple analytical and phenomenologically compelling nonperturbative approximation to the full light-front QCD Hamiltonian 'Light-Front Holography'. Light-Front Holography is in fact one of the most remarkable features of the AdS/CFT correspondence. The Hamiltonian equation of motion in the light-front (LF) is frame independent and has a structure similar to eigenmode equations in AdS space. This makes a direct connection of QCD with AdS/CFT methods possible. Remarkably, the AdS equations correspond to the kinetic energy terms of the partons inside a hadron, whereas the interaction terms build confinement and correspond to the truncation of AdS space in an effective dual gravity approximation. One can also study the gauge/gravity duality starting from the bound-state structure of hadrons in QCD quantized in the light-front. The LF Lorentz-invariant Hamiltonian equation for the relativistic bound-state system is P{sub {mu}}P{sup {mu}}|{psi}(P)> = (P{sup +}P{sup -} - P{sub {perpendicular}}{sup 2})|{psi}(P)> = M{sup 2}|{psi}(P)>, P{sup {+-}} = P{sup 0} {+-} P{sup 3}, where the LF time evolution operator P{sup -} is determined canonically from the QCD Lagrangian. To a first semiclassical approximation, where quantum loops and quark masses are not included, this leads to a LF Hamiltonian equation which describes the bound-state dynamics of light hadrons in terms of an invariant impact variable {zeta} which measures the separation of the partons within the hadron at equal light-front time {tau} = x{sup 0} + x{sup 3}. This allows us to identify the holographic variable z in AdS space with an impact variable {zeta}. The resulting Lorentz-invariant Schroedinger equation for general spin incorporates color confinement and is systematically improvable. Light-front holographic methods were originally introduced by matching the electromagnetic current matrix elements in AdS space with the corresponding expression using LF theory in physical space time. It was also shown that one obtains identical holographic mapping using the matrix elements of the energy-momentum tensor by perturbing the AdS metric around its static solution. A gravity dual to QCD is not known, but th

  11. Adaptive Importance Sampling via Stochastic Convex Programming

    E-Print Network [OSTI]

    Adaptive Importance Sampling via Stochastic Convex Programming Ernest K. Ryu1 and Stephen P. Boyd1 Abstract We show that the variance of the Monte Carlo estimator that is importance sam- pled from

  12. U.S. LNG Imports from Oman

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    Otay Mesa, CA Alamo, TX El Paso, TX Galvan Ranch, TX Hidalgo, TX McAllen, TX Penitas, TX LNG Imports from Algeria Cove Point, MD Everett, MA Lake Charles, LA LNG Imports from...

  13. U.S. LNG Imports from Egypt

    Gasoline and Diesel Fuel Update (EIA)

    Otay Mesa, CA Alamo, TX El Paso, TX Galvan Ranch, TX Hidalgo, TX McAllen, TX Penitas, TX LNG Imports from Algeria Cove Point, MD Everett, MA Lake Charles, LA LNG Imports from...

  14. U.S. LNG Imports from Malaysia

    Gasoline and Diesel Fuel Update (EIA)

    Otay Mesa, CA Alamo, TX El Paso, TX Galvan Ranch, TX Hidalgo, TX McAllen, TX Penitas, TX LNG Imports from Algeria Cove Point, MD Everett, MA Lake Charles, LA LNG Imports from...

  15. U.S. LNG Imports from Indonesia

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    Otay Mesa, CA Alamo, TX El Paso, TX Galvan Ranch, TX Hidalgo, TX McAllen, TX Penitas, TX LNG Imports from Algeria Cove Point, MD Everett, MA Lake Charles, LA LNG Imports from...

  16. U.S. LNG Imports from Brunei

    Gasoline and Diesel Fuel Update (EIA)

    Otay Mesa, CA Alamo, TX El Paso, TX Galvan Ranch, TX Hidalgo, TX McAllen, TX Penitas, TX LNG Imports from Algeria Cove Point, MD Everett, MA Lake Charles, LA LNG Imports from...

  17. U.S. LNG Imports from Peru

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    Otay Mesa, CA Alamo, TX El Paso, TX Galvan Ranch, TX Hidalgo, TX McAllen, TX Penitas, TX LNG Imports from Algeria Cove Point, MD Everett, MA Lake Charles, LA LNG Imports from...

  18. U.S. LNG Imports from Yemen

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    Otay Mesa, CA Alamo, TX El Paso, TX Galvan Ranch, TX Hidalgo, TX McAllen, TX Penitas, TX LNG Imports from Algeria Cove Point, MD Everett, MA Lake Charles, LA LNG Imports from...

  19. U.S. LNG Imports from Norway

    Gasoline and Diesel Fuel Update (EIA)

    Otay Mesa, CA Alamo, TX El Paso, TX Galvan Ranch, TX Hidalgo, TX McAllen, TX Penitas, TX LNG Imports from Algeria Cove Point, MD Everett, MA Lake Charles, LA LNG Imports from...

  20. U.S. LNG Imports from Qatar

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    Otay Mesa, CA Alamo, TX El Paso, TX Galvan Ranch, TX Hidalgo, TX McAllen, TX Penitas, TX LNG Imports from Algeria Cove Point, MD Everett, MA Lake Charles, LA LNG Imports from...

  1. U.S. LNG Imports from Algeria

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    Otay Mesa, CA Alamo, TX El Paso, TX Galvan Ranch, TX Hidalgo, TX McAllen, TX Penitas, TX LNG Imports from Algeria Cove Point, MD Everett, MA Lake Charles, LA LNG Imports from...

  2. U.S. LNG Imports from Nigeria

    Gasoline and Diesel Fuel Update (EIA)

    Otay Mesa, CA Alamo, TX El Paso, TX Galvan Ranch, TX Hidalgo, TX McAllen, TX Penitas, TX LNG Imports from Algeria Cove Point, MD Everett, MA Lake Charles, LA LNG Imports from...

  3. U.S. LNG Imports from Australia

    Annual Energy Outlook 2013 [U.S. Energy Information Administration (EIA)]

    Otay Mesa, CA Alamo, TX El Paso, TX Galvan Ranch, TX Hidalgo, TX McAllen, TX Penitas, TX LNG Imports from Algeria Cove Point, MD Everett, MA Lake Charles, LA LNG Imports from...

  4. Imports and Exports of Fishery Products

    E-Print Network [OSTI]

    Imports and Exports of Fishery Products Annual Summary, 2002 IMPORTS. U.S. imports of edible. EXPORTS. U.S. exports of edible fishery products of domestic origin were 1,056,306 tons valued at $3.0 billion, compared with 1,139,744 tons at $3.1 billion exported in 2001. Fresh and frozen items were 883

  5. 5, 47014738, 2005 The importance of

    E-Print Network [OSTI]

    Boyer, Edmond

    ACPD 5, 4701­4738, 2005 The importance of mesoscale to forecast air pollution J. L. Palau et al and Physics Discussions The importance of meteorological scales to forecast air pollution scenarios. 4701 #12;ACPD 5, 4701­4738, 2005 The importance of mesoscale to forecast air pollution J. L. Palau et

  6. Sandia National Laboratories: efficient LED lighting

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Partnership, Research & Capabilities, Solid-State Lighting Solid state lighting (SSL), which uses light-emitting diodes (LEDs), has the potential to be 10 times more energy...

  7. Sandia National Laboratories: Light Creation Materials

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    TechnologiesLight Creation Materials Light Creation Materials Overview of SSL Light Creation Materials Different families of inorganic semiconductor materials can...

  8. Ecological Consequences of Artificial Night Lighting

    E-Print Network [OSTI]

    Piselli, Kathy

    2006-01-01T23:59:59.000Z

    of Artificial Night Lighting Catherine Rich and Travisof artificial night lighting. This book provides editedage of modern urban lighting was ushered in. Coincidentally,

  9. Sandia National Laboratories: Solid-State Lighting

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Lighting Developments to 2030 On July 30, 2012, in Lighting Technologies, Costs, and Energy Demand: Global Developments to 2030 View Slides: Lighting Technologies, Costs, and...

  10. LIGHTING CONTROLS: SURVEY OF MARKET POTENTIAL

    E-Print Network [OSTI]

    Verderber, R.R.

    2010-01-01T23:59:59.000Z

    REFERENCES Task Report to Lighting Systems Research,Berkeley Laboratory, "Lighting Control System Market1980). Task Report to Lighting Systems Research, Lawrence

  11. Demand Responsive Lighting: A Scoping Study

    E-Print Network [OSTI]

    Rubinstein, Francis; Kiliccote, Sila

    2007-01-01T23:59:59.000Z

    3 3.0 Previous Experience with Demand Responsive Lighting11 4.3. Prevalence of Lighting13 4.4. Impact of Title 24 on Lighting

  12. Municipal Consortium LED Street Lighting Workshop Presentations...

    Broader source: Energy.gov (indexed) [DOE]

    A Rational View of LM-79 Reports, IES Files, and Product Variation Gary Steinberg, GE Lighting Solutions Solid-State Street Lighting: Calculating Light Loss Factors Dana Beckwith,...

  13. Municipal Consortium LED Street Lighting Workshop Presentations...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    National Association of Energy Services Companies Calculating Light Loss Factors for Solid-State Lighting Systems Chad Stalker, Philips Lumileds Lighting Intro to MSSLC's...

  14. Light propagation and Imaging in Indefinite Metamaterials

    E-Print Network [OSTI]

    Yao, Jie

    2010-01-01T23:59:59.000Z

    photolithography by polarized light,” Applied PhysicsZhang, “Imaging visible light using anisotropic metamaterialcross-sectional review of the light propagation of TE mode (

  15. Advances in Lighting

    E-Print Network [OSTI]

    Tumber, A. J.

    1981-01-01T23:59:59.000Z

    colour rendition. The quartz-halogen incandescent lam s operate at higher temperatures, and have a somewhat higher efficacy, but they are rarely used except for special applicati ns. 3-2 High Intensity Discharge Lamps. Mercury is the grandfather... of the H.I.D. lamps. Its blue-green light, has been used almost exclusively for streetlighti and, often with colour-improving phospho it is still being used in industrial and commercial applications. Reactor-type ballasted mercury lamps can now...

  16. Pedestrian Friendly Outdoor Lighting

    SciTech Connect (OSTI)

    Miller, Naomi J.; Koltai, Rita; McGowan, Terry

    2013-12-31T23:59:59.000Z

    This GATEWAY report discusses the problems of pedestrian lighting that occur with all technologies with a focus on the unique optical options and opportunities offered by LEDs through the findings from two pedestrian-focused projects, one at Stanford University in California, and one at the Chautauqua Institution in upstate New York. Incorporating user feedback this report reviews the tradeoffs that must be weighed among visual comfort, color, visibility, efficacy and other factors to stimulate discussion among specifiers, users, energy specialists, and in industry in hopes that new approaches, metrics, and standards can be developed to support pedestrian-focused communities, while reducing energy use.

  17. Lighting Test Facilities

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHigh SchoolIn12electron 9 5Let us countLighting Sign In About

  18. Lighting | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnual SiteofEvaluatingGroup |Jilin ZhongdiantouLichuan City Yujiang River ValleyLighting

  19. New light on Dark Cosmos

    E-Print Network [OSTI]

    E. Gaztanaga; M. Manera; T. Multamaki

    2005-09-22T23:59:59.000Z

    Recent studies by a number of independent collaborations, have correlated the CMB temperatures measured by the WMAP satellite with different galaxy surveys that trace the matter distribution with light from the whole range of the electromagnetic spectrum: radio, far-infrared, optical and X-ray surveys. The new data systematically finds positive correlations, indicating a rapid slow down in the growth of structure in the universe. Individual cross-correlation measurements are of low significance, but we show that combining data at different redshifts introduces important new constraints. Contrary to what happens at low redshifts, for a fixed $\\Omm$, the higher the dark energy contend, $\\Ol$, the lower the ISW cross-correlation amplitude. At 68% confidence level, the data finds new independent evidence of dark energy: $\\Ol =0.42-1.22$ . It also confirms, to higher significance, the presence of a large dark matter component: $\\Omm =0.18-0.34$, exceeding the density of baryonic matter, but far from the critical value. Combining these new constraints with the prior of a flat universe, or the prior of an accelerating universe provides strong new evidence for a dark cosmos. Combination with supernova data yields $\\Ol = 0.71 \\pm 0.13$, $\\Omm = 0.29 \\pm 0.04$. If we also assume a flat universe, we find $\\Ol = 0.70 \\pm 0.05$ and $w = -1.02 \\pm 0.17$ for a constant dark energy equation of state.

  20. Natural Supersymmetry without Light Higgsinos

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Cohen, T.; Kearney, J.; Luty, M. A.

    2015-04-01T23:59:59.000Z

    We present a mechanism that allows a large Higgsino mass without large fine-tuning. The Higgs is a pseudo Nambu-Goldstone boson (PNGB) of the global symmetry breaking pattern $SO(5) \\to SO(4)$. Because of the PNGB nature of the light Higgs, the $SO(5)$ invariant Higgsino mass does not directly contribute to the Higgs mass. Large couplings in the Higgs sector that spontaneously breaks $SO(5)$ minimize the tuning, and are also motivated by the requirements of generating a sufficiently large Higgs quartic coupling and of maintaining a natural approximate global $SO(5)$ symmetry. When these conditions are imposed, theories of this type predict heavymore »Higgsinos. This construction differs from composite Higgs models in that no new particles are introduced to form complete $SO(5)$ multiplets involving the top quark---the stop is the only top partner. Compatibility with Higgs coupling measurements requires cancelations among contributions to the Higgs mass squared parameter at the 10% level. An important implication of this construction is that the compressed region of stop and sbottom searches can still be natural.« less

  1. Natural Supersymmetry without Light Higgsinos

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Cohen, T. [Princeton Univ., Princeton NJ, (United States); Kearney, J. [Fermi National Accelerator Laboratory, Batavia, IL, (United States); Luty, M. A. [University of California Davis, Davis, CA (United States)

    2015-04-01T23:59:59.000Z

    We present a mechanism that allows a large Higgsino mass without large fine-tuning. The Higgs is a pseudo Nambu-Goldstone boson (PNGB) of the global symmetry breaking pattern $SO(5) \\to SO(4)$. Because of the PNGB nature of the light Higgs, the $SO(5)$ invariant Higgsino mass does not directly contribute to the Higgs mass. Large couplings in the Higgs sector that spontaneously breaks $SO(5)$ minimize the tuning, and are also motivated by the requirements of generating a sufficiently large Higgs quartic coupling and of maintaining a natural approximate global $SO(5)$ symmetry. When these conditions are imposed, theories of this type predict heavy Higgsinos. This construction differs from composite Higgs models in that no new particles are introduced to form complete $SO(5)$ multiplets involving the top quark---the stop is the only top partner. Compatibility with Higgs coupling measurements requires cancelations among contributions to the Higgs mass squared parameter at the 10% level. An important implication of this construction is that the compressed region of stop and sbottom searches can still be natural.

  2. Electro-Production of Light Lambda Hypernuclei

    SciTech Connect (OSTI)

    Nakamura, Satoshi N. [TOHOKU

    2013-02-01T23:59:59.000Z

    Through the study of light hypernuclei, we can learn about hyperon nucleon interaction. The hypernuclear spectroscopy with electron beams is one of most powerful methods to study detailed structure of light hypernuclei thanks to its high energy resolution. With a decade of efforts at Jefferson Lab, the spectroscopy of ? hypernuclei with an electron beam is now established. Observation of {sup 7}{sub ?}He which gave the last missing binding energy of the A = 7, T = 1 iso-triplet hypernuclei provides an important experimental input for the charge symmetry breaking (CSB) effect of the ?N interaction. Further study about A = 4 hypernuclear iso-doublet, {sup 4}{sub ?}H and {sup 4}{sub ?}He , is necessary and such experiments are now planned.

  3. Making More Light with Less Energy

    SciTech Connect (OSTI)

    Kuritzky, Leah; Jewell, Jason

    2013-07-18T23:59:59.000Z

    Representing the Center for Energy Efficient Materials (CEEM), this document is one of the entries in the Ten Hundred and One Word Challenge. As part of the challenge, the 46 Energy Frontier Research Centers were invited to represent their science in images, cartoons, photos, words and original paintings, but any descriptions or words could only use the 1000 most commonly used words in the English language, with the addition of one word important to each of the EFRCs and the mission of DOE: energy. The mission of the CEEM is to discover and develop materials that control the interactions among light, electricity, and heat at the nanoscale for improved solar energy conversion, solid-state lighting, and conversion of heat into electricity.

  4. Posters | Posters --721 Exploring lighting cultures

    E-Print Network [OSTI]

    Boyer, Edmond

    Posters | Posters -- 721 Exploring lighting cultures Beyond light and emotions Vincent LAGANIER 1 , Jasmine van der POL 2 1. Lighting Applications Services (LiAS), Philips Lighting, France vincent.laganier@philips.com 2

  5. LIGHTING CONTROLS: SURVEY OF MARKET POTENTIAL

    E-Print Network [OSTI]

    Verderber, R.R.

    2010-01-01T23:59:59.000Z

    Floors Floor Area Lighting Power Density Light Output Lampenergy den- sity and power density for lighting to 3.5 kWh/Lighting Level (Lumens/Watt) (Footcandles) Power Density (

  6. Radioluminescent lighting for Alaskan runway lighting and marking

    SciTech Connect (OSTI)

    Jensen, G.A.; Leonard, L.E.

    1985-03-01T23:59:59.000Z

    Alaska and other far northern areas have special logistical, environmental, and economic problems that make radioluminescent (RL) lighting applications, especially in the area of airport lighting, an attractive alternative to electrical systems and flare pots. Tests and demonstrations of prototype systems conducted in Alaska over the past two years have proved the basic technological worth of RL airport lighting systems for civilian and military use. If regulatory issues and other factors identified during these tests can be favorably resolved and if the system and its components can be refined through production engineering, attractive applications for RL airfield lighting systems in Alaska and other remote locations could result.

  7. Energy Savings Estimates of Light Emitting Diodes in Niche Lighting...

    Office of Environmental Management (EM)

    in Niche Lighting Applications Prepared for: Building Technologies Program Office of Energy Efficiency and Renewable Energy U.S. Department of Energy Prepared by: Navigant...

  8. Embodied Energy and Off-Grid Lighting

    E-Print Network [OSTI]

    Alstone, Peter

    2012-01-01T23:59:59.000Z

    as a point of comparison with LED lighting product embodieda fairer comparison between off- grid LED lighting and other

  9. Northeast Energy Efficiency Partnerships: Advanced Lighting Controls...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Northeast Energy Efficiency Partnerships: Advanced Lighting Controls - 2015 Peer Review Northeast Energy Efficiency Partnerships: Advanced Lighting Controls - 2015 Peer Review...

  10. Overcoming Common Pitfalls: Energy Efficient Lighting Projects...

    Broader source: Energy.gov (indexed) [DOE]

    Overcoming Common Pitfalls: Energy Efficient Lighting Projects Overcoming Common Pitfalls: Energy Efficient Lighting Projects Transcript Presentation More Documents & Publications...

  11. Light Meson Distribution Amplitudes

    E-Print Network [OSTI]

    R. Arthur; P. A. Boyle; D. Brömmel; M. A. Donnellan; J. M. Flynn; A. Jüttner; H. Pedroso de Lima; T. D. Rae; C. T. Sachrajda; B. Samways

    2010-11-12T23:59:59.000Z

    We calculated the first two moments of the light-cone distribution amplitudes for the pseudoscalar mesons ($\\pi$ and $K$) and the longitudinally polarised vector mesons ($\\rho$, $K^*$ and $\\phi$) as part of the UKQCD and RBC collaborations' $N_f=2+1$ domain-wall fermion phenomenology programme. These quantities were obtained with a good precision and, in particular, the expected effects of $SU(3)$-flavour symmetry breaking were observed. Operators were renormalised non-perturbatively and extrapolations to the physical point were made, guided by leading order chiral perturbation theory. The main results presented are for two volumes, $16^3\\times 32$ and $24^3\\times 64$, with a common lattice spacing. Preliminary results for a lattice with a finer lattice spacing, $32^3\\times64$, are discussed and a first look is taken at the use of twisted boundary conditions to extract distribution amplitudes.

  12. Light modulating device

    DOE Patents [OSTI]

    Rauh, R.D.; Goldner, R.B.

    1989-12-26T23:59:59.000Z

    In a device for transmitting light, means for controlling the transmissivity of the device, including a ceramic, reversibly electrochromic, crystalline element having a highly reflective state when injected with electrons and charge compensating ions and a highly transmissive state when the electrons and ions are removed, the crystalline element being characterized as having a reflectivity of at least 50% in the reflective state and not greater than 10% in the transmissive state, and means for modulating the crystalline element between the reflective and transmissive states by injecting ions into the crystalline element in response to an applied electrical current of a first polarity and removing the ions in response to an applied electrical current of a second polarity are disclosed. 1 fig.

  13. Energy and lighting

    SciTech Connect (OSTI)

    Berman, S.

    1985-01-01T23:59:59.000Z

    Advances in research for new types of lighting with increased efficacies (lumens/watt) are discussed in the following areas: (1) high-frequency, solid-state ballasts, (2) isotopic enhancement of mercury isotopes, (3) magnetic augmentation, (4) electrodeless, ultra-high frequency, (5) tuned phosphors, (6) two-photon phosphors, (7) heat mirrors, and (3) advanced control circuits to take advantage of daylight and occupancy. As of 1985, improvements in efficacy have been accomplished on an economic basis to save energy for (1) high-frequency ballasts (25%), (2) isotopic enhancement (5%), and (8) advanced control circuits (up to 50%). Most of these advances depend on a deeper understanding of the weakly ionized plasma as a radiating and diffusing medium. 3 figures, 4 tables.

  14. Light modulating device

    DOE Patents [OSTI]

    Rauh, R. David (Newton, MA); Goldner, Ronald B. (Lexington, MA)

    1989-01-01T23:59:59.000Z

    In a device for transmitting light, means for controlling the transmissivity of the device, including a ceramic, reversibly electrochromic, crystalline element having a highly reflective state when injected with electrons and charge compensating ions and a highly transmissive state when the electrons and ions are removed, the crystalline element being characterized as having a reflectivity of at least 50% in the reflective state and not greater than 10% in the transmissive state, and means for modulating the crystalline element between the reflective and transmissive states by injecting ions into the crystalline element in response to an applied electrical current of a first polarity and removing the ions in response to an applied electrical current of a second polarity.

  15. Ultrafast Magnetic Light

    E-Print Network [OSTI]

    Makarov, Sergey V; Krasnok, Alexander E; Belov, Pavel A

    2015-01-01T23:59:59.000Z

    We propose a novel concept for efficient dynamic tuning of optical properties of a high refractive index subwavelength nanoparticle with a magnetic Mie-type resonance by means of femtosecond laser radiation. This concept is based on ultrafast generation of electron-hole plasma within such nanoparticle, drastically changing its transient dielectric permittivity. This allows to manipulate by both electric and magnetic nanoparticle responses, resulting in dramatic changes of its extinction cross section and scattering diagram. Specifically, we demonstrate the effect of ultrafast switching-on a Huygens source in the vicinity of the magnetic dipole resonance. This approach enables to design ultrafast and compact optical switchers and modulators based on the "ultrafast magnetic light" concept.

  16. Geothermal: Website Policies and Important Links

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Website Policies and Important Links Geothermal Technologies Legacy Collection HelpFAQ | Site Map | Contact Us HomeBasic Search About Publications Advanced Search New Hot Docs...

  17. Automatic Mechetronic Wheel Light Device

    DOE Patents [OSTI]

    Khan, Mohammed John Fitzgerald (Silver Spring, MD)

    2004-09-14T23:59:59.000Z

    A wheel lighting device for illuminating a wheel of a vehicle to increase safety and enhance aesthetics. The device produces the appearance of a "ring of light" on a vehicle's wheels as the vehicle moves. The "ring of light" can automatically change in color and/or brightness according to a vehicle's speed, acceleration, jerk, selection of transmission gears, and/or engine speed. The device provides auxiliary indicator lights by producing light in conjunction with a vehicle's turn signals, hazard lights, alarm systems, and etc. The device comprises a combination of mechanical and electronic components and can be placed on the outer or inner surface of a wheel or made integral to a wheel or wheel cover. The device can be configured for all vehicle types, and is electrically powered by a vehicle's electrical system and/or battery.

  18. anticorrelation light yield: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    for Light Engineering Websites Summary: Smart lighting: New Roles for Light in the Solid State Lighting World Robert F. Karlicek, Jr as the largest supplier of LED Lighting...

  19. LED Lighting Off the Grid

    Energy Savers [EERE]

    D. & Kammen, D. M. Decentralized energy systems for clean electricity access. Nature Climate Change accepted, in press, (2015). Off-Grid Status Quo : Fuel Based Lighting...

  20. Pedestrian-Friendly Nighttime Lighting

    Broader source: Energy.gov [DOE]

    This November 19, 2013 webinar presented issues and considerations related to pedestrian-friendly nighttime lighting, such as color rendering, safety, and adaptation. When it comes to outdoor...

  1. Linac Coherent Light Source Overview

    Broader source: Energy.gov [DOE]

    Take an animated tour of the Linac Coherent Light Source (LCLS). Follow the laser pulse from the injector gun all the way through to the Far Experimental Hall.

  2. Linac Coherent Light Source Overview

    SciTech Connect (OSTI)

    None

    2010-01-01T23:59:59.000Z

    Take an animated tour of the Linac Coherent Light Source (LCLS). Follow the laser pulse from the injector gun all the way through to the Far Experimental Hall.

  3. Utility lighting summit proves illuminating

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Utility-lighting-summit-proves-illuminating Sign In About | Careers | Contact | Investors | bpa.gov Search News & Us Expand News & Us Projects & Initiatives Expand Projects...

  4. Linac Coherent Light Source Overview

    ScienceCinema (OSTI)

    None

    2013-05-29T23:59:59.000Z

    Take an animated tour of the Linac Coherent Light Source (LCLS). Follow the laser pulse from the injector gun all the way through to the Far Experimental Hall.

  5. Lighting with Paint FABIO PELLACINI

    E-Print Network [OSTI]

    Pellacini, Fabio

    Lighting with Paint FABIO PELLACINI Dartmouth College and FRANK BATTAGLIA, R. KEITH MORLEY, animation, rendering, optimization, painting ACM Reference Format: Pellacini, F., Battaglia, F., Morley, R

  6. Arnold Schwarzenegger LIGHTING RESEARCH PROGRAM

    E-Print Network [OSTI]

    Institute; David Shiller, Environmental Protection Agency. Program Advisory Committee: Ron Lewis Corporation; Don Aumann, California Lighting Technology Center; Holly Larsen, Larsen Communications

  7. FEATURE FOCUS: Fuels & Combustion a new dawn for

    E-Print Network [OSTI]

    economy, proponents say. Ultra-low sulfur fuel, set to become available in the United States in 2006's light-duty diesels are quiet and clean, and they provide excellent low-end torque and superior fuel

  8. Light storage protocols in Tm:YAG

    E-Print Network [OSTI]

    T. Chanelière; R. Lauro; J. Ruggiero; J. -L. Le Gouët

    2009-11-17T23:59:59.000Z

    We present two quantum memory protocols for solids: A stopped light approach based on spectral hole burning and the storage in an atomic frequency comb. These procedures are well adapted to the rare-earth ion doped crystals. We carefully clarify the critical steps of both. On one side, we show that the slowing-down due to hole-burning is sufficient to produce a complete mapping of field into the atomic system. On the other side, we explain the storage and retrieval mechanism of the Atomic Frequency Comb protocol. This two important stages are implemented experimentally in Tm$^{3+}$- doped yttrium-aluminum-garnet crystal.

  9. IMPORTED SOIL OR SOIL-FORMING MATERIALS

    E-Print Network [OSTI]

    IMPORTED SOIL OR SOIL-FORMING MATERIALS PLACEMENT BPG NOTE 5 Best Practice Guidance for Land of heavy industry. Soil material initially present on a site may have been removed or stored in bunds the original soil that has been stored or importing a soil from elsewhere or using a soil-forming material

  10. Electric power is an increasingly important aspect of modern society. We are extremely dependent on electric-

    E-Print Network [OSTI]

    Florida, University of

    , Infrastructure Figure 1. Structure and economic impacts of wood-fueled electric power generation in a localFact Sheet Electric power is an increasingly important aspect of modern society. We are extremely dependent on electric- ity for many uses, such as heating, cooling, lighting, and information technology

  11. Benzene is an important industrial chemical (> 2 billion gallons produced annually in the

    E-Print Network [OSTI]

    California at Berkeley, University of

    Benzene is an important industrial chemical (> 2 billion gallons produced annually in the United leukemia (Snyder 2002). However, the mechanisms of benzene-induced hematotoxicity and leukemo- genesis further light on these mechanisms and better understand the risk benzene poses, we examined the effects

  12. Strategies of Asian oil-importing countries

    SciTech Connect (OSTI)

    Yang, M. [Asian Inst. of Tech., Bangkok (Thailand)

    1997-04-01T23:59:59.000Z

    Various strategies are used by oil-importing countries to reduce their economic dependence on imported oil: national oil production, energy conservation, and the change of economic structures from high energy intensity sectors to low ones. In this article, the roles of these different strategies have been identified for 10 selected oil-importing countries in Asia: Bangladesh, India, Nepal, Pakistan, Sri Lanka, the Philippines, Thailand, Hong Kong, R.O Korea, and Taiwan. The results show that most of the selected countries (although Hong Kong and Taiwan are independent economic entities, for simplicity, the author refers to them as countries) have succeeded in reducing their national economy dependence on imported oil since 1973. Hong Kong, Sri Lanka, Thailand, and India are among the most successful countries, with more than 40% reduction in their economic dependence on imported oil.

  13. Light-by-Light Scattering Effect in Light-Cone Supergraphs

    E-Print Network [OSTI]

    Renata Kallosh; Pierre Ramond

    2010-06-24T23:59:59.000Z

    We give a relatively simple explanation of the light-cone supergraph prediction for the UV properties of the maximally supersymmetric theories. It is based on the existence of a dynamical supersymmetry which is not manifest in the light-cone supergraphs. It suggests that N=4 supersymmetric Yang-Mills theory is UV finite and N=8 supergravity is UV finite at least until 7 loops whereas the $n$-point amplitudes have no UV divergences at least until $L=n+3$. Here we show that this prediction can be deduced from the properties of light-cone supergraphs analogous to the light-by-light scattering effect in QED. A technical aspect of the argument relies on the observation that the dynamical supersymmetry action is, in fact, a compensating field-dependent gauge transformation required for the retaining the light-cone gauge condition $A_+=0$.

  14. World Oil Prices in AEO2006 (released in AEO2006)

    Reports and Publications (EIA)

    2006-01-01T23:59:59.000Z

    World oil prices in the Annual Energy Outlook 2006 (AEO) reference case are substantially higher than those in the AEO2005 reference case. In the AEO2006 reference case, world crude oil prices, in terms of the average price of imported low-sulfur, light crude oil to U.S. refiners, decline from current levels to about $47 per barrel (2004 dollars) in 2014, then rise to $54 per barrel in 2025 and $57 per barrel in 2030. The price in 2025 is approximately $21 per barrel higher than the corresponding price projection in the AEO2005 reference case.

  15. Crop Management Factors: What is Important?

    E-Print Network [OSTI]

    Kastens, Terry L.; Dhuyvetter, Kevin C.; Nivens, Heather; Klinefelter, Danny A.

    1999-09-29T23:59:59.000Z

    Crop Management Factors: What is Important? Terry L. Kastens, Kevin C. Dhuyvetter, Heather Nivens and Danny Klinefelter* Defining Good Farm Management Economically, a well-managed farm is one that consistently makes greater prof- its than similarly...

  16. A Dynamic Model with Import Quota Constraints

    E-Print Network [OSTI]

    Basak, Suleyman

    2004-07-09T23:59:59.000Z

    The analysis of import quotas is predominantly based on a static model, which is unable to capture the fact that a quota is imposed over a period of time. This article develops a continuous-time model ...

  17. Double Importance Sampling Val'erie Ventura

    E-Print Network [OSTI]

    Double Importance Sampling Val'erie Ventura Department of Statistics Carnegie Mellon University (Newton and Geyer, 1994, Ventura, 1998), where estimation must be made with respect to many first

  18. Light derivation for compositing digital elements into live action photography 

    E-Print Network [OSTI]

    Bennatt, William Rhett

    2000-01-01T23:59:59.000Z

    for the challenges introduced by new and potential projects. The LightPick tool developed for this thesis is one such tool. To better understand how computers are used to create digital effects today, it is important to trace the development of computer technology...

  19. UV-light enhanced oxidation of carbon nanotubes M. Grujicica,*

    E-Print Network [OSTI]

    Grujicic, Mica

    (as well as other gases) is very important as SWCNTs are being considered in chemical sensor applications. It is well established that exposure of the materials to UV light can give rise to various photo-induced phe- nomena such as photo-induced polymerization in poly- meric materials (e.g. [4]) and accelerated

  20. OLED lighting devices having multi element light extraction and luminescence conversion layer

    DOE Patents [OSTI]

    Krummacher, Benjamin Claus (Regensburg, DE); Antoniadis, Homer (Mountain View, CA)

    2010-11-16T23:59:59.000Z

    An apparatus such as a light source has a multi element light extraction and luminescence conversion layer disposed over a transparent layer of the light source and on the exterior of said light source. The multi-element light extraction and luminescence conversion layer includes a plurality of light extraction elements and a plurality of luminescence conversion elements. The light extraction elements diffuses the light from the light source while luminescence conversion elements absorbs a first spectrum of light from said light source and emits a second spectrum of light.

  1. Device structure for OLED light device having multi element light extraction and luminescence conversion layer

    DOE Patents [OSTI]

    Antoniadis; Homer (Mountain View, CA), Krummacher; Benjamin Claus (Regensburg, DE)

    2008-01-22T23:59:59.000Z

    An apparatus such as a light source has a multi-element light extraction and luminescence conversion layer disposed over a transparent layer of the light source and on the exterior of said light source. The multi-element light extraction and luminescence conversion layer includes a plurality of light extraction elements and a plurality of luminescence conversion elements. The light extraction elements diffuses the light from the light source while luminescence conversion elements absorbs a first spectrum of light from said light source and emits a second spectrum of light.

  2. Angular constraint on light-trapping absorption enhancement in solar cells

    E-Print Network [OSTI]

    Yu, Zongfu

    2010-01-01T23:59:59.000Z

    Light trapping for solar cells can reduce production cost and improve energy conversion efficiency. Understanding some of the basic theoretical constraints on light trapping is therefore of fundamental importance. Here, we develop a general angular constraint on the absorption enhancement in light trapping. We show that there is an upper limit for the angular integration of absorption enhancement factors. This limit is determined by the number of accessible resonances supported by an absorber.

  3. Induction Lighting: An Old Lighting Technology Made New Again...

    Broader source: Energy.gov (indexed) [DOE]

    25 years if operated 10 hours a day. The technology, however, is far from new. Nikola Tesla demonstrated induction lighting in the late 1890s around the same time that his rival,...

  4. Using QECBs for Street Lighting Upgrades: Lighting the Way to...

    Broader source: Energy.gov (indexed) [DOE]

    Summarizes how the City of San Diego leveraged 13.1 million in qualified energy conservation bonds to increase the size of a street lighting upgrade project. Author: Lawrence...

  5. Quasi light fields: Extending the light field to coherent radiation

    E-Print Network [OSTI]

    Accardi, Anthony J.

    Imaging technologies such as dynamic viewpoint generation are engineered for incoherent radiation using the traditional light field, and for coherent radiation using electromagnetic field theory. We present a model of ...

  6. 46th Street Pilot Street Lighting Project

    E-Print Network [OSTI]

    Minnesota, University of

    Street to 48th Street) as standard high-pressure sodium (HPS) lighting comparison corridor #12;The over time #12;Initial Lighting Comparison #12;Lighting Project Location #12;Street Light Layout 3046th Street Pilot Street Lighting Project A Joint Venture: Hennepin County & City of Minneapolis

  7. Projection screen having reduced ambient light scattering

    DOE Patents [OSTI]

    Sweatt, William C. (Albuquerque, NM)

    2010-05-11T23:59:59.000Z

    An apparatus and method for improving the contrast between incident projected light and ambient light reflected from a projection screen are described. The efficiency of the projection screen for reflection of the projected light remains high, while permitting the projection screen to be utilized in a brightly lighted room. Light power requirements from the projection system utilized may be reduced.

  8. Identifying Lights with their Switches Jayadev Misra

    E-Print Network [OSTI]

    Misra, Jayadev

    Identifying Lights with their Switches Jayadev Misra 09/07/2012 Problem Description Given are N switches and N lights where each switch controls exactly one light and each light is controlled by exactly of selecting some number of switches and turning them on, and, presumably, noting the lights that come

  9. Light baryon spectroscopy

    SciTech Connect (OSTI)

    Crede, Volker [Florida State University, Department of Physics, Tallahassee, FL (United States)

    2013-03-25T23:59:59.000Z

    The spectrum of excited baryons serves as an excellent probe of quantum chromodynamics (QCD). In particular, highly-excited baryon resonances are sensitive to the details of quark confinement which is only poorly understood within QCD. Facilities worldwide such as Jefferson Lab, ELSA, and MAMI, which study the systematics of hadron spectra in photo- and electroproduction experiments, have accumulated a large amount of data in recent years including unpolarized cross section and polarization data for a large variety of meson-production reactions. These are important steps toward complete experiments that will allow us to unambiguously determine the scattering amplitude in the underlying reactions and to identify the broad and overlapping baryon resonance contributions. Several new nucleon resonances have been proposed and changes to the baryon listing in the 2012 Review of Particle Physics reflect the progress in the field.

  10. Inorganic volumetric light source excited by ultraviolet light

    DOE Patents [OSTI]

    Reed, S.; Walko, R.J.; Ashley, C.S.; Brinker, C.J.

    1994-04-26T23:59:59.000Z

    The invention relates to a composition for the volumetric generation of radiation. The composition comprises a porous substrate loaded with a component capable of emitting radiation upon interaction with an exciting radiation. Preferably, the composition is an aerogel substrate loaded with a component, e.g., a phosphor, capable of interacting with exciting radiation of a first energy, e.g., ultraviolet light, to produce radiation of a second energy, e.g., visible light. 4 figures.

  11. Saturable absorption and 'slow light'

    E-Print Network [OSTI]

    Adrian C Selden

    2006-03-25T23:59:59.000Z

    Quantitative evaluation of some recent 'slow light' experiments based on coherent population oscillations (CPO) shows that they can be more simply interpreted as saturable absorption phenomena. Therefore they do not provide an unambiguous demonstration of 'slow light'. Indeed a limiting condition on the spectral bandwidth is not generally satisfied, such that the requirements for burning a narrow spectral hole in the homogeneously broadened absorption line are not met. Some definitive tests of 'slow light' phenomena are suggested, derived from analysis of phase shift and pulse delay for a saturable absorber

  12. Power management is important for multicore architectures. One important challenge for multicore

    E-Print Network [OSTI]

    Sorin, Daniel J.

    1 Abstract Power management is important for multicore architectures. One important challenge difficulty varies among designs, depending, for example, on the particular power management mechanisms systems motivate the development and evaluation of efficient power manage- ment solutions targeted

  13. Saturated and efficient blue phosphorescent organic light emitting devices with Lambertian angular emission

    E-Print Network [OSTI]

    Saturated and efficient blue phosphorescent organic light emitting devices with Lambertian angular a microcavity to optimize the color of a phosphorescent organic light emitting device OLED based on the-sky blue.1063/1.2742577 The development of a stable, efficient, and saturated blue remains an important goal for phosphorescent organic

  14. Animal Pathogen/Product Import Importing "Animal" Pathogens from Outside Canada

    E-Print Network [OSTI]

    Animal Pathogen/Product Import Importing "Animal" Pathogens from Outside Canada 1) Permits is required from the CFIA* (a division of Agriculture Canada), please go to the CFIA website at http importation permit from Public Health Agency Canada may also be required. #12;

  15. The Diesel Engine Powering Light-Duty Vehicles: Today and Tomorrow

    Broader source: Energy.gov (indexed) [DOE]

    diesel-powered light-duty vehicles 1990 1995 2000 2005 2010 2015 2020 2025 Energy Greenhouse effect CO 2 Exhaust gas emissions CO, NO x , HC, PM Importance Environmental driving...

  16. Next Generation Light Source Workshops

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Next Generation Light Source Workshops A series of workshops will be held in late August with the goal of refining the scientific drivers for the facility and translating the...

  17. Columbia Water & Light- Solar Rebates

    Broader source: Energy.gov [DOE]

    Columbia Water & Light electric customers are eligible for a $400 rebate for the purchase of a new solar water heater. To apply for this rebate, a customer submits a pre-approval application to...

  18. Arnold Schwarzenegger LIGHTING RESEARCH PROGRAM

    E-Print Network [OSTI]

    ; James Bryan, Arden Realty; Peter Ngai, Peerless; David Malman, Architectural Lighting Design; Ron Lewis) ; Terry McGowan, ALA; Adriana Valencia (CPUC alternate). Program Advisory Committee: Ron Lewis; Holly Larsen, Larsen Communications. Please cite this repor

  19. Arnold Schwarzenegger LIGHTING RESEARCH PROGRAM

    E-Print Network [OSTI]

    Design Group; Bill Daiber, WFD Associates. Program Advisory Committee: Ron Lewis, Department of Energy Buchan, Sacramento Municipal Utility District. Editorial assistance: Holly Larsen, Larsen Communications Lighting Technology Center; Holly Larsen, Larsen Communications. Please cite

  20. Arnold Schwarzenegger LIGHTING RESEARCH PROGRAM

    E-Print Network [OSTI]

    the contribution of the below individuals: Program Advisory Committee: Ron Lewis, Department of Energy; Jerry Mills Lighting Technology Center; Holly Larsen, Larsen Communications. Please cite this report as follows

  1. Light Duty Vehicle CNG Tanks

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Light Duty Vehicle CNG Tanks Dane A. Boysen, PhD Program Director Advanced Research Projects Agency-Energy, US DOE dane.boysen@doe.gov Fiber Reinforced Polymer Composite...

  2. Novel phosphors for solid state lighting

    E-Print Network [OSTI]

    Furman, Joshua D

    2010-11-16T23:59:59.000Z

    Solid state white light emitting diode lighting devices outperform conventional light sources in terms of lifetime, durability, and lumens per watt. However, the capital contribution is still to high to encourage widespread adoption. Furthermore...

  3. Toward ZnO Light Emitting Diode

    E-Print Network [OSTI]

    Liu, Jianlin

    2008-01-01T23:59:59.000Z

    applications such as light emitting diodes (LEDs) and laser009 "Toward ZnO Light Emitting Diode" Jianlin Liu July 2008Title: “Toward ZnO Light Emitting Diode” Sponsor: UC Energy

  4. CAMPUS INFRASTRUCTURE & SERVICES CIS-Standard-Lighting

    E-Print Network [OSTI]

    Viglas, Anastasios

    ...........................................................................................................5 5.6 Light fittings and lux performance requirements for various University space types.....5 5...........................................................................12 5.8 EXTERIOR LIGHTING.......................................................................................................12 5.8.2 Exterior Light Poles, Fixings and Wiring

  5. EECBG Success Story: Lighting Retrofit Improving Visibility,...

    Broader source: Energy.gov (indexed) [DOE]

    New LED lighting fixtures (right) emit a whiter light than existing high-pressure sodium cobra head streetlights (left) and don't spill light onto nearby houses. | Photos courtesy...

  6. Embodied Energy and Off-Grid Lighting

    E-Print Network [OSTI]

    Alstone, Peter

    2012-01-01T23:59:59.000Z

    Self-reported Impacts of LED Lighting Technology Comparedto Fuel-based Lighting on Night Market Business Prosperity28, no. 4, pp. 533-546. Lighting Africa (prepared by Dalberg

  7. LIGHT SCATTERING STUDIES OF SILICA AEROGELS

    E-Print Network [OSTI]

    Hunt, A.J.

    2010-01-01T23:59:59.000Z

    van de Hulst, H.C. , Light Scattering by Small Particles,A New Polarization-Modulated Light Scattering Instrument,"and interpretation of light scattering effects in aerogels.

  8. Advanced Light Source Activity Report 2005

    E-Print Network [OSTI]

    Tamura Ed., Lori S.

    2010-01-01T23:59:59.000Z

    upgrade on the Advanced Light Source," Nucl. Instrum. Meth.n photoemission at the Advanced Light Source," Radiât. Phys.high-pressure studies at the Advanced Light Source w i t h a

  9. Beyond the Replacement Paradigm: Smart Lighting

    E-Print Network [OSTI]

    Salama, Khaled

    Switches · Smart Building & Grid Interfaces · Efficient full spectrum LEDs without droop · Versatile, low - Visible Light Communications Integration of smart fixtures, networked sensors and control systemsBeyond the Replacement Paradigm: Smart Lighting Robert F. Karlicek, Jr. Director, Smart Lighting

  10. Lumental : web-based tunable lighting control

    E-Print Network [OSTI]

    Hall, Harrison King

    2012-01-01T23:59:59.000Z

    Dynamically adjusting the light spectrum of spectrum-tunable light fixtures promises significant energy savings over binary or incremental dimming control. To enable this level of controllability, lighting must evolve from ...

  11. MFR PAPER 1271 Importance of Eelgrass

    E-Print Network [OSTI]

    MFR PAPER 1271 Importance of Eelgrass Beds in Puget Sound GORDON W. THAYER and RONALD C. PHILLIPS to almot liquid mud . Eelgrass, Zostera marina, which oc- curs extensively in Puget Sound , i a generally ,000 acre of the bottom of Puget Sound is covered by eelgra . On the Pacific coast this seagra

  12. Compacted Soil Liner Interface Strength Importance

    E-Print Network [OSTI]

    Case Study Compacted Soil Liner Interface Strength Importance Timothy D. Stark, F.ASCE1 ; Hangseok interface is not the geomembrane (GM)/compacted low-permeability soil liner (LPSL) but a soil­soil interface placing the cover soil from bottom to top. DOI: 10.1061/(ASCE)GT.1943-5606 .0000556. © 2012 American

  13. The Importance of Carbon Footprint Estimation Boundaries

    E-Print Network [OSTI]

    Kammen, Daniel M.

    The Importance of Carbon Footprint Estimation Boundaries H . S C O T T M A T T H E W S , C H R I and organizations are pursuing "carbon footprint" projects to estimate their own contributions to global climate change. Protocol definitions from carbon registries help organizations analyze their footprints

  14. Background Material Important Questions about Magnetism

    E-Print Network [OSTI]

    Mojzsis, Stephen J.

    Background Material Important Questions about Magnetism: 1) What is Magnetism?Magnetism is a force or repulsion due to charge is called the electric force. But what about magnetism, is there a fundamental property of some matter that makes things magnetic? The answer is: "sort of." Electric current

  15. Automated Storage Reclamation Using Temporal Importance Annotations

    E-Print Network [OSTI]

    Chandra, Surendar

    Automated Storage Reclamation Using Temporal Importance Annotations Surendar Chandra, Ashish.edu Abstract This work focuses on scenarios that require the storage of large amounts of data. Such sys- tems require the ability to either continuously increase the storage space or reclaim space by deleting

  16. Commercial Lighting Solutions, Webtool Peer Review Report

    SciTech Connect (OSTI)

    Jones, Carol C.; Meyer, Tracy A.

    2009-06-17T23:59:59.000Z

    The Commercial Lighting Solutions (CLS) project directly supports the U.S. Department of Energy’s Commercial Building Energy Alliance efforts to design high performance buildings. CLS creates energy efficient best practice lighting designs for widespread use, and they are made available to users via an interactive webtool that both educates and guides the end user through the application of the Lighting Solutions. This report summarizes the peer review of the beta version of the CLS webtool, which contains retail box lighting solutions. The methodology for the peer review process included data collection (stakeholder input), analysis of the comments, and organization of the input into categories for prioritization of the comments against a set of criteria. Based on this process, recommendations were developed about which feedback should be addressed for the release of version 1.0 of the webtool at the Lightfair conference in New York City in May 2009. Due to the volume of data (~500 comments) the methodology for addressing the peer review comments was central to the success of the ultimate goal of improving the tool. The comments were first imported into a master spreadsheet, and then grouped and organized in several layers. Solutions to each comment were then rated by importance and feasibility to determine the practicality of resolving the concerns of the commenter in the short-term or long-term. The rating system was used as an analytical tool, but the results were viewed thoughtfully to ensure that they were not the sole the factor in determining which comments were recommended for near-term resolution. The report provides a list of the top ten most significant and relevant improvements that will be made within the webtool for version 1.0 as well as appendices containing the short-term priorities in additional detail. Peer review comments that are considered high priority by the reviewers and the CLS team but cannot be completed for Version 1.0 are listed as long-term recommendations.

  17. Lighting and GeometryLighting and Geometry Prof. Michael Misha Kazhdan

    E-Print Network [OSTI]

    Fröhlich, Peter

    Lighting and GeometryLighting and Geometry Prof. Michael Misha Kazhdan misha· The viewer · The lights N Viewer · The lights · The geometry · The surface properties N L2 V Viewer L1Outline · Surface Properties (Review) · Lighting· Lighting · Geometry· Geometry #12;Surface Properties (Review

  18. Is Light-Tree Structure Optimal for Multicast Routing in Sparse Light Splitting WDM Networks?

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Is Light-Tree Structure Optimal for Multicast Routing in Sparse Light Splitting WDM Networks? Fen session in sparse light splitting Wavelength Divi- sion Multiplexing (WDM) networks, a light as possible. Different from a light- tree, a light-hierarchy accepts cycles, which are used to traverse

  19. New Laser's "First Light" Shatters Record | Jefferson...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Jefferson National Accelerator Facility have delivered first light from their Free Electron Laser (FEL). Only 2 years after ground was broken for the FEL, infrared light of more...

  20. Sandia National Laboratories: Solid-State Lighting

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    light, which could also impact so-called smart (or higher functionality) lighting, another . Among InGaN ... Research Challenge 3: Competing Radiative and...

  1. Indianapolis Power & Light- Business Energy Incentives Program

    Broader source: Energy.gov [DOE]

    The Indiana Power and Light Business (IPL) Energy Incentives Program assists commercial and industrial customers with reducing energy consumption through three common types of equipment: lighting,...

  2. Municipal Consortium LED Street Lighting Workshop Presentations...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Controls Norma Isahakian, City of Los Angeles Bureau of Street Lighting San Jose's "Smart" LED Streetlights: Controlled Amy Olay, City of San Jose Adaptive Lighting Controls...

  3. OTEC- Commercial Lighting Retrofit Rebate Program

    Broader source: Energy.gov [DOE]

    The Oregon Trail Electric Consumers Cooperative (OTEC) offers a commercial lighting retrofit program that provides rebates for commercial businesses that change existing lighting to more energy...

  4. DOE Solid-State Lighting in Higher Ed Facilities

    SciTech Connect (OSTI)

    Miller, Naomi J.; Curry, Ku'Uipo J.

    2010-07-20T23:59:59.000Z

    The focus of the workshop was on higher education facilities because college and university campuses are an important market for lighting products and they use almost every kind of luminaire on the market. This workshop was seen as a chance for SSL manufacturers large and small to get the inside scoop from a group of people that specify, pay for, install, use, maintain, and dispose of lighting systems for nearly every type of application. Workshop attendees explored the barriers to SSL adoption, the applications where SSL products could work better than existing technologies, and where SSL luminaires are currently falling short. This report summarizes the Workshop activities and presentation highlights.

  5. Full light absorption in single arrays of spherical nanoparticles

    E-Print Network [OSTI]

    Ra'di, Y; Kosulnikov, S U; Omelyanovich, M M; Morits, D; Osipov, A V; Simovski, C R; Tretyakov, S A

    2015-01-01T23:59:59.000Z

    In this paper we show that arrays of core-shell nanoparticles function as effective thin absorbers of light. In contrast to known metamaterial absorbers, the introduced absorbers are formed by single planar arrays of spherical inclusions and enable full absorption of light incident on either or both sides of the array. We demonstrate possibilities for realizing different kinds of symmetric absorbers, including resonant, ultra-broadband, angularly selective, and all-angle absorbers. The physical principle behind these designs is explained considering balanced electric and magnetic responses of unit cells. Photovoltaic devices and thermal emitters are the two most important potential applications of the proposed designs.

  6. THE LUMINA PROJECT http://light.lbl.gov

    E-Print Network [OSTI]

    Jacobson, Arne

    components for the LED lights. #12;2 Introduction Solid-state lighting based on light emitting diode (LED

  7. Oscillating light wall above a sunspot light bridge

    E-Print Network [OSTI]

    Yang, Shuhong; Jiang, Fayu; Xiang, Yongyuan

    2015-01-01T23:59:59.000Z

    With the high tempo-spatial \\emph{Interface Region Imaging Spectrograph} 1330 {\\AA} images, we find that many bright structures are rooted in the light bridge of NOAA 12192, forming a \\emph{light wall}. The light wall is brighter than the surrounding areas, and the wall top is much brighter than the wall body. The New Vacuum Solar Telescope H$\\alpha$ and the \\emph{Solar Dynamics Observatory} 171 {\\AA} and 131 {\\AA} images are also used to study the light wall properties. In 1330 {\\AA}, 171 {\\AA}, and 131 {\\AA}, the top of the wall has a higher emission, while in the H$\\alpha$ line, the wall top emission is very low. The wall body corresponds to bright areas in 1330 {\\AA} and dark areas in the other lines. The top of the light wall moves upward and downward successively, performing oscillations in height. The deprojected mean height, amplitude, oscillation velocity, and the dominant period are determined to be 3.6 Mm, 0.9 Mm, 15.4 km s$^{-1}$, and 3.9 min, respectively. We interpret the oscillations of the lig...

  8. Determining Vulnerability Importance in Environmental Impact Assessment

    SciTech Connect (OSTI)

    Toro, Javier, E-mail: jjtoroca@unal.edu.co [Institute of Environmental Studies, National University of Colombia, Bogota (Colombia); Duarte, Oscar, E-mail: ogduartev@unal.edu.co [Department of Electrical and Electronics Engineering, National University of Colombia, Bogota (Colombia); Requena, Ignacio, E-mail: requena@decsai.ugr.es [Department of Computer Science and Artificial Intelligence, University of Granada (Spain); Zamorano, Montserrat, E-mail: zamorano@ugr.es [Department of Civil Engineering, University of Granada (Spain)

    2012-01-15T23:59:59.000Z

    The concept of vulnerability has been used to describe the susceptibility of physical, biotic, and social systems to harm or hazard. In this sense, it is a tool that reduces the uncertainties of Environmental Impact Assessment (EIA) since it does not depend exclusively on the value assessments of the evaluator, but rather is based on the environmental state indicators of the site where the projects or activities are being carried out. The concept of vulnerability thus reduces the possibility that evaluators will subjectively interpret results, and be influenced by outside interests and pressures during projects. However, up until now, EIA has been hindered by a lack of effective methods. This research study analyzes the concept of vulnerability, defines Vulnerability Importance and proposes its inclusion in qualitative EIA methodology. The method used to quantify Vulnerability Importance is based on a set of environmental factors and indicators that provide a comprehensive overview of the environmental state. The results obtained in Colombia highlight the usefulness and objectivity of this method since there is a direct relation between this value and the environmental state of the departments analyzed. - Research Highlights: Black-Right-Pointing-Pointer The concept of vulnerability could be considered defining Vulnerability Importance included in qualitative EIA methodology. Black-Right-Pointing-Pointer The use of the concept of environmental vulnerability could reduce the subjectivity of qualitative methods of EIA. Black-Right-Pointing-Pointer A method to quantify the Vulnerability Importance proposed provides a comprehensive overview of the environmental state. Black-Right-Pointing-Pointer Results in Colombia highlight the usefulness and objectivity of this method.

  9. Demonstration Assessment of Light Emitting Diode (LED) Street...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Demonstration Assessment of Light Emitting Diode (LED) Street Lighting, Final Report Demonstration Assessment of Light Emitting Diode (LED) Street Lighting, Final Report This...

  10. LED Provides Effective and Efficient Parking Area Lighting at...

    Broader source: Energy.gov (indexed) [DOE]

    White Light Options for Parking Area Lighting Demonstration Assessment of Light Emitting Diode (LED) Street Lighting, Final Report Guide to FEMP-Designated Parking Lot...

  11. Demonstration Assessment of Light-Emitting Diode (LED) Freezer...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Demonstration Assessment of Light-Emitting Diode (LED) Freezer Case Lighting Demonstration Assessment of Light-Emitting Diode (LED) Freezer Case Lighting This document is a report...

  12. Strong interaction between light and a single trapped atom without a cavity

    E-Print Network [OSTI]

    Meng Khoon Tey; Zilong Chen; Syed Abdullah Aljunid; Brenda Chng; Florian Huber; Gleb Maslennikov; Christian Kurtsiefer

    2008-06-12T23:59:59.000Z

    Coupling of light to an atom at single quanta level with high probability is a building block for many quantum information processing protocols. It is commonly believed that efficient coupling is only achievable with the assistance of a cavity. Here, we report on an observation of substantial coupling between a light beam and a single $^{87}$Rb atom in a direct extinction measurement by focusing light to a small spot with a single lens. Our result opens a new perspective on processing quantum information carried by light using atoms, and is important to many ongoing experiments that require strong coupling of single photons to an atom in free space.

  13. Light Field Denoising, Light Field Superresolution and Stereo Camera Based Refocussing using a GMM Light Field Patch Prior

    E-Print Network [OSTI]

    Mellor-Crummey, John

    Light Field Denoising, Light Field Superresolution and Stereo Camera Based Refocussing using a GMM Light Field Patch Prior Kaushik Mitra and Ashok Veeraraghavan ECE, Rice University Houston, Tx 77005 Kaushik.Mitra@rice.edu, vashok@rice.edu Abstract With the recent availability of commercial light field

  14. Dispersive approach to hadronic light-by-light scattering

    E-Print Network [OSTI]

    Gilberto Colangelo; Martin Hoferichter; Massimiliano Procura; Peter Stoffer

    2014-08-22T23:59:59.000Z

    Based on dispersion theory, we present a formalism for a model-independent evaluation of the hadronic light-by-light contribution to the anomalous magnetic moment of the muon. In particular, we comment on the definition of the pion pole in this framework and provide a master formula that relates the effect from pi pi intermediate states to the partial waves for the process gamma^* gamma^* --> pi pi. All contributions are expressed in terms of on-shell form factors and scattering amplitudes, and as such amenable to an experimental determination.

  15. Method for measuring changes in light absorption of highly scattering media

    DOE Patents [OSTI]

    Bigio, Irving J. (Los Alamos, NM); Johnson, Tamara M. (Los Alamos, NM); Mourant, Judith R. (Los Alamos, NM)

    2002-01-01T23:59:59.000Z

    The noninvasive measurement of variations in absorption that are due to changes in concentrations of biochemically relevant compounds in tissue is important in many clinical settings. One problem with such measurements is that the pathlength traveled by the collected light through the tissue depends on the scattering properties of the tissue. It is demonstrated, using both Monte Carlo simulations and experimental measurements, that for an appropriate separation between light-delivery and light-collection fibers, the pathlength of the collected photons is insensitive to scattering parameters for the range of parameters typically found in tissue. This is important for developing rapid, noninvasive, inexpensive, and accurate methods for measuring absorption changes in tissue.

  16. Enhancing the use of coals by gas reburning-sorbent injection. Volume 3, Gas reburning-sorbent injection at Edwards Unit 1, Central Illinois Light Company

    SciTech Connect (OSTI)

    NONE

    1994-10-01T23:59:59.000Z

    Design work has been completed for a Gas Reburning-Sorbent Injection (GR-SI) system to reduce emissions of NO{sub x}, and SO{sub 2} from a wall fired unit. A GR-SI system was designed for Central Illinois Light Company`s Edwards Station Unit 1, located in Bartonville, Illinois. The unit is rated at 117 MW(e) (net) and is front wall fired with a pulverized bituminous coal blend. The goal of the project was to reduce emissions of NO{sub x} by 60%, from the ``as found`` baseline of 0.98 lb/MBtu (420 mg/MJ), and to reduce emissions of S0{sub 2} by 50%. Since the unit currently fires a blend of high sulfur Illinois coal and low sulfur Kentucky coal to meet an S0{sub 2} limit Of 1.8 lb/MBtu (770 mg/MJ), the goal at this site was amended to meeting this limit while increasing the fraction of high sulfur coal to 57% from the current 15% level. GR-SI requires injection of natural gas into the furnace at the level of the top burner row, creating a fuel-rich zone in which NO{sub x} formed in the coal zone is reduced to N{sub 2}. The design natural gas input corresponds to 18% of the total heat input. Burnout (overfire) air is injected at a higher elevation to burn out fuel combustible matter at a normal excess air level of 18%. Recycled flue gas is used to increase the reburning fuel jet momentum, resulting in enhanced mixing. Recycled flue gas is also used to cool the top row of burners which would not be in service during GR operation. Dry hydrated lime sorbent is injected into the upper furnace to react with S0{sub 2}, forming solid CaSO{sub 4} and CaSO{sub 3}, which are collected by the ESP. The SI system design was optimized with respect to gas temperature, injection air flow rate, and sorbent dispersion. Sorbent injection air flow is equal to 3% of the combustion air. The design includes modifications of the ESP, sootblowing, and ash handling systems.

  17. Electromagnetic reactions on light nuclei

    E-Print Network [OSTI]

    Sonia Bacca; Saori Pastore

    2014-07-13T23:59:59.000Z

    Electromagnetic reactions on light nuclei are fundamental to advance our understanding of nuclear structure and dynamics. The perturbative nature of the electromagnetic probes allows to clearly connect measured cross sections with the calculated structure properties of nuclear targets. We present an overview on recent theoretical ab-initio calculations of electron-scattering and photonuclear reactions involving light nuclei. We encompass both the conventional approach and the novel theoretical framework provided by chiral effective field theories. Because both strong and electromagnetic interactions are involved in the processes under study, comparison with available experimental data provides stringent constraints on both many-body nuclear Hamiltonians and electromagnetic currents. We discuss what we have learned from studies on electromagnetic observables of light nuclei, starting from the deuteron and reaching up to nuclear systems with mass number A=16.

  18. Enrichment of light hydrocarbon mixture

    DOE Patents [OSTI]

    Yang; Dali (Los Alamos, NM); Devlin, David (Santa Fe, NM); Barbero, Robert S. (Santa Cruz, NM); Carrera, Martin E. (Naperville, IL); Colling, Craig W. (Warrenville, IL)

    2010-08-10T23:59:59.000Z

    Light hydrocarbon enrichment is accomplished using a vertically oriented distillation column having a plurality of vertically oriented, nonselective micro/mesoporous hollow fibers. Vapor having, for example, both propylene and propane is sent upward through the distillation column in between the hollow fibers. Vapor exits neat the top of the column and is condensed to form a liquid phase that is directed back downward through the lumen of the hollow fibers. As vapor continues to ascend and liquid continues to countercurrently descend, the liquid at the bottom of the column becomes enriched in a higher boiling point, light hydrocarbon (propane, for example) and the vapor at the top becomes enriched in a lower boiling point light hydrocarbon (propylene, for example). The hollow fiber becomes wetted with liquid during the process.

  19. Enrichment of light hydrocarbon mixture

    DOE Patents [OSTI]

    Yang, Dali (Los Alamos, NM); Devlin, David (Santa Fe, NM); Barbero, Robert S. (Santa Cruz, NM); Carrera, Martin E. (Naperville, IL); Colling, Craig W. (Warrenville, IL)

    2011-11-29T23:59:59.000Z

    Light hydrocarbon enrichment is accomplished using a vertically oriented distillation column having a plurality of vertically oriented, nonselective micro/mesoporous hollow fibers. Vapor having, for example, both propylene and propane is sent upward through the distillation column in between the hollow fibers. Vapor exits neat the top of the column and is condensed to form a liquid phase that is directed back downward through the lumen of the hollow fibers. As vapor continues to ascend and liquid continues to countercurrently descend, the liquid at the bottom of the column becomes enriched in a higher boiling point, light hydrocarbon (propane, for example) and the vapor at the top becomes enriched in a lower boiling point light hydrocarbon (propylene, for example). The hollow fiber becomes wetted with liquid during the process.

  20. An Assessment of the U.S. Residential Lighting Market

    SciTech Connect (OSTI)

    Jennings, Judy; Brown, Rich; Moezzi, Mithra; Mills, Evan; Sardinsky, Robert

    1995-10-01T23:59:59.000Z

    This report provides background data upon which residential lighting fixture energy conservation programs can be built. The current stock of residential lighting is described by usage level, lamp wattage, fixture type, and location within the house. Data are discussed that indicate that 25% of residential fixtures are responsible for 80% of residential lighting energy use, and that justify targeting these fixtures as candidates for retrofit with energy-efficient fixtures. Fixtures determined to have the highest energy use are hardwired ceiling fixtures in kitchens, living/family rooms, dining rooms, and outdoors. An assessment of the market for residential fixtures shows that nearly half of new residential fixtures are imported, 61% of new fixtures sold are hardwired, and about half of all new fixtures sold are for ceiling installation.

  1. The Possible Loss of Venezuelan Heavy Crude Oil Imports Underscores the Strategic Importance of the

    E-Print Network [OSTI]

    Texas at Austin, University of

    The Possible Loss of Venezuelan Heavy Crude Oil Imports Underscores the Strategic Importance crude, making reliance on Canadian heavy crude oil more significant, and the approval of the Keystone XL of ConocoPhillips' Petrozuata- Hamaca and ExxonMobil's Cerro Negro Orinoco Belt heavy oil projects

  2. Dynamic power management (DPM) is important for multicore architectures. One important challenge for

    E-Print Network [OSTI]

    Sorin, Daniel J.

    1 Abstract Dynamic power management (DPM) is important for multicore architectures. One important). The verification diffi- culty varies among designs, depending, for example, on the particular power management systems motivate the development and evaluation of efficient power manage- ment solutions targeted

  3. Importance of Nuclear DataImportance of Nuclear Data to the Naval Nuclear Propulsion Program

    E-Print Network [OSTI]

    Danon, Yaron

    Importance of Nuclear DataImportance of Nuclear Data to the Naval Nuclear Propulsion Program Don Cores · Project Prometheus · Some Very Recent Criticality Analyses #12;Use of Early RPI Measurements · Criticality Analyses of Under-moderated Systemsy y y · Most Reactive Condition ­ Highest Water Density

  4. Crude Oil Imports From Persian Gulf

    Gasoline and Diesel Fuel Update (EIA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for On-Highway4,1,50022,3,,,,6,1,9,1,50022,3,,,,6,1,Decade Year-0E (2001)gasoline prices4Consumption TheX ImeansCrude Oil Imports

  5. U.S. Imports from All Countries

    U.S. Energy Information Administration (EIA) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are nowTotal" (Percent) Type: Sulfur Content API GravityDakota" "Fuel, quality",Area: U.S. East Coast (PADD 1) New EnglandReserves (BillionImport Area: U.S.

  6. Category:Imported Properties | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnualProperty EditCalifornia:Power LPInformationCashtonGo Back to PV Economics ByImported

  7. Light and Color in Nature -Scattering Effects -

    E-Print Network [OSTI]

    Assarsson, Ulf

    1 Seminar WS 2003/04 Light and Color in Nature - Scattering Effects - Marcus Magnor WS03/04: Light and Color in Nature ­ Scattering Overview · Last Lecture ­ Interference · Today ­ Light scattering: water rendering #12;2 WS03/04: Light and Color in Nature ­ Scattering List of Topics · Rainbow ­ Stephan

  8. Today LED Holiday Lights, Tomorrow the World?

    SciTech Connect (OSTI)

    Gordon, Kelly L.

    2004-12-20T23:59:59.000Z

    This article for The APEM Advantage, the quarterly newsletter of the Association of Professional Energy Managers (APEM) describes the recent increase in the popularity of light emitting diode (LED) lighting and compares LED light output with that of incandescent and compact fluorescent lighting.

  9. National Synchrotron Light Source annual report 1991

    SciTech Connect (OSTI)

    Hulbert, S.L.; Lazarz, N.N. (eds.)

    1992-04-01T23:59:59.000Z

    This report contains abstracts from research conducted at the national synchrotron light source. (LSP)

  10. Nonimaging light concentrator with uniform irradiance

    DOE Patents [OSTI]

    Winston, Roland (Chicago, IL); Gee, Randy C. (Arvada, CO)

    2003-04-01T23:59:59.000Z

    A nonimaging light concentrator system including a primary collector of light, an optical mixer disposed near the focal zone for collecting light from the primary collector, the optical mixer having a transparent entrance aperture, an internally reflective housing for substantially total internal reflection of light, a transparent exit aperture and an array of photovoltaic cells disposed near the transparent exit aperture.

  11. Residential Lighting: Title 24 and Technology Update

    E-Print Network [OSTI]

    California at Davis, University of

    Residential Lighting: Title 24 and Technology Update Best practices in lighting design to comply with California's Title 24 energy code Kelly Cunningham, Outreach Director California Lighting Technology Center AS AN IMPLIED ENDORSEMENT. #12;INTRODUCTION California Lighting Technology Center, UC Davis To accelerate

  12. Light-Induced Atomic Desorption (LIAD)

    E-Print Network [OSTI]

    Budker, Dmitry

    in density n0=the initial density more intense higher density!! #12;Light Friquency Low light power (0.56m, polysiloxane, etc) #12;Time Dependence exposed to 514-nm desorbing light at room temperature (~20) density increase in density!! coating is replenished #12;Light Intensity 0=relative rate of increase of the vapor

  13. Creative and Constructive Play with Light

    E-Print Network [OSTI]

    9/19/12 1 Creative and Constructive Play with Light Presented by Krissy Opferman & Charline Tomer CMU Children's School PAEYC Conference on Play! September 21, 2012 Big Ideas for Light Central concepts to learn We need light to see things. Without light, we would not be able to see

  14. Light Induced Guard Cell Sunando Roy

    E-Print Network [OSTI]

    Albert, Réka

    Light Induced Guard Cell Signaling Sunando Roy #12;Guard cells and the stomata The tradeoff between water and carbon dioxide Roelfsema et. al. New Phytologist (2005) 167: 665 - 691 #12;The Light Signaling features · The blue light signaling carried out through ion channels · The red light signaling occurs

  15. Trapping Light With Mirrors David Milovich Jr.

    E-Print Network [OSTI]

    Milovich, David

    Trapping Light With Mirrors David Milovich Jr. February 20, 2004 Abstract. We show that, given finitely many line-segment mirrors in the plane, that do not touch, and an arbitrary point source of light emitted light beams escape. This result is shown to imply that, for a given point source of light

  16. National Synchrotron Light Source Activity Report 1998

    SciTech Connect (OSTI)

    Rothman, Eva

    1999-05-01T23:59:59.000Z

    National Synchrotron Light Source Activity Report for period October 1, 1997 through September 30, 1998

  17. Organic electroluminescent devices having improved light extraction

    DOE Patents [OSTI]

    Shiang, Joseph John (Niskayuna, NY)

    2007-07-17T23:59:59.000Z

    Organic electroluminescent devices having improved light extraction include a light-scattering medium disposed adjacent thereto. The light-scattering medium has a light scattering anisotropy parameter g in the range from greater than zero to about 0.99, and a scatterance parameter S less than about 0.22 or greater than about 3.

  18. Light celebrating place, West Texas Road Trip

    E-Print Network [OSTI]

    Mulholland, Jill Cecilia

    2009-05-15T23:59:59.000Z

    of Lighting Design: Speer and Hitler, 1936 Paris World?s Fair, German Pavilion .................................................................. 200 68 The History of Lighting Design: Speer and Hitler, 1937 Nuremburg Rally... ....................................................................................... 200 69 The History of Lighting Design: Speer and Hitler, 1938 Berlin Streets for a Mussolini Visit................................................... 201 70 Contemporary Light and Art: Patriotism and Memorial............................ 202...

  19. Visible Light Communications: Recent Activities in Japan

    E-Print Network [OSTI]

    Lü, James Jian-Qiang

    The Graduate School of System Design and Management, Keio University, Yokohama, Japan Smart Spaces: A Smart, visible light LEDs are beginning to be used in every home and office, which makes visible light LEDs ideal, and the market share of LED lighting will be more than 30 percent of total lighting market in 2016. Prediction

  20. Illuminating system and method for specialized and decorative lighting using liquid light guides

    DOE Patents [OSTI]

    Zorn, Carl J. (Yorktown, VA); Kross, Brian J. (Yorktown, VA); Majewski, Stanislaw (Grafton, VA); Wojcik, Randolph F. (Yorktown, VA)

    1998-01-01T23:59:59.000Z

    The present invention comprises an illumination system for specialized decorative lighting including a light source, a flexible plastic tube sheath for distributing the light to a remote location, a transparent liquid core filling the tube that has an index of refraction greater than that of the plastic tube and an arrangement where light coupled from the light source is caused to leak from the liquid light guide at desired locations for the purposes of specialized lighting, such as underwater illumination in swimming pools.

  1. Monitored lighting energy savings from dimmable lighting controls in

    E-Print Network [OSTI]

    , product, or process disclosed, or represents that its use would not infringe privately owned rights. Reference herein to any specific commercial product, process, or service by its trade name, trademark 94720, USA Abstract Digital addressable, dimmable lighting controls were introduced to the US market

  2. Damage tolerant light absorbing material

    DOE Patents [OSTI]

    Lauf, Robert J. (Oak Ridge, TN); Hamby, Jr., Clyde (Harriman, TN); Akerman, M. Alfred (Knoxville, TN); Seals, Roland D. (Oak Ridge, TN)

    1993-01-01T23:59:59.000Z

    A light absorbing article comprised of a composite of carbon-bonded carbon fibers, prepared by: blending carbon fibers with a carbonizable organic powder to form a mixture; dispersing the mixture into an aqueous slurry; vacuum molding the aqueous slurry to form a green article; drying and curing the green article to form a cured article; and, carbonizing the cured article at a temperature of at least about 1000.degree. C. to form a carbon-bonded carbon fiber light absorbing composite article having a bulk density less than 1 g/cm.sup.3.

  3. Solid state electrochromic light modulator

    DOE Patents [OSTI]

    Cogan, S.F.; Rauh, R.D.

    1990-07-03T23:59:59.000Z

    An all solid-state variable transmission electrochromic device has a source of charge compensating ions. An inorganic oxide counter electrode film which on reduction with the accompanying insertion of the charge compensating ions increases its transmission of light of predetermined wavelength is separated from a primary electrochromic film which on reduction with the accompanying insertion of the charge compensating ions decreases its transmission of light of predetermined wavelength by an insulating electrolyte film that transports the charge compensating ions. First and second electrodes are contiguous with the inorganic oxide counter electrode film and the primary electrochromic film, respectively, and separated by the three films. 4 figs.

  4. Solid state electrochromic light modulator

    SciTech Connect (OSTI)

    Cogan, Stuart F.; Rauh, R. David

    1993-12-07T23:59:59.000Z

    An all solid-state variable transmission electrochromic device has a source of charge compensating ions. An inorganic oxide counterelectrode film which on reduction with the accompanying insertion of the charge compensating ions increases its transmission of light of predetermined wavelength is separated from a primary electrochromic film which on reduction with the accompanying insertion of the charge compensating ions decreases its transmission of light of predetermined wavelength by an insulating electrolyte film that transports the charge compensating ions. First and second electrodes are contiguous with the inorganic oxide counter electrode film and the primary electrochromic film, respectively, and separated by the three films.

  5. Solid state electrochromic light modulator

    DOE Patents [OSTI]

    Cogan, Stuart F. (111 Downey St., Norwood, MA 02062); Rauh, R. David (111 Downey St., Norwood, MA 02062)

    1990-01-01T23:59:59.000Z

    An all solid-state variable transmission electrochromic device has a source of charge compensating ions. An inorganic oxide counterelectrode film which on reduction with the accompanying insertion of the charge compensating ions increases its transmission of light of predetermined wavelength is separated from a primary electrochromic film which on reduction with the accompanying insertion of the charge compensating ions decreases its transmission of light of predetermined wavelength by an insulating electrolyte film that transports the charge compensating ions. First and second electrodes are contiguous with the inorganic oxide counter electrode film and the primary electrochromic film, respectively, and separated by the three films.

  6. Solid state electrochromic light modulator

    SciTech Connect (OSTI)

    Cogan, Stuart F. (Sudbury, MA); Rauh, R. David (Newton, MA)

    1993-01-01T23:59:59.000Z

    An all solid-state variable transmission electrochromic device has a source of charge compensating ions. An inorganic oxide counterelectrode film which on reduction with the accompanying insertion of the charge compensating ions increases its transmission of light of predetermined wavelength is separated from a primary electrochromic film which on reduction with the accompanying insertion of the charge compensating ions decreases its transmission of light of predetermined wavelength by an insulating electrolyte film that transports the charge compensating ions. First and second electrodes are contiguous with the inorganic oxide counter electrode film and the primary electrochromic film, respectively, and separated by the three films.

  7. Damage tolerant light absorbing material

    DOE Patents [OSTI]

    Lauf, R.J.; Hamby, C. Jr.; Akerman, M.A.; Seals, R.D.

    1993-09-07T23:59:59.000Z

    A light absorbing article comprised of a composite of carbon-bonded carbon fibers, is prepared by: blending carbon fibers with a carbonizable organic powder to form a mixture; dispersing the mixture into an aqueous slurry; vacuum molding the aqueous slurry to form a green article; drying and curing the green article to form a cured article; and, carbonizing the cured article at a temperature of at least about 1000 C to form a carbon-bonded carbon fiber light absorbing composite article having a bulk density less than 1 g/cm[sup 3]. 9 figures.

  8. Review: Semiconductor Quantum Light Sources

    E-Print Network [OSTI]

    Andrew J Shields

    2007-04-03T23:59:59.000Z

    Lasers and LEDs display a statistical distribution in the number of photons emitted in a given time interval. New applications exploiting the quantum properties of light require sources for which either individual photons, or pairs, are generated in a regulated stream. Here we review recent research on single-photon sources based on the emission of a single semiconductor quantum dot. In just a few years remarkable progress has been made in generating indistinguishable single-photons and entangled photon pairs using such structures. It suggests it may be possible to realise compact, robust, LED-like semiconductor devices for quantum light generation.

  9. LED Lighting Facts®

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(FactDepartment ofLetter Report:40PM toLED Lighting Facts LED Lighting Facts LEDLED

  10. Chip-Scale Power Conversion for LED Lighting: Integrated Power Chip Converter for Solid-State Lighting

    SciTech Connect (OSTI)

    None

    2010-10-01T23:59:59.000Z

    ADEPT Project: Teledyne is developing cost-effective power drivers for energy-efficient LED lights that fit on a compact chip. These power drivers are important because they transmit power throughout the LED device. Traditional LED driver components waste energy and don't last as long as the LED itself. They are also large and bulky, so they must be assembled onto a circuit board separately which increases the overall manufacturing cost of the LED light. Teledyne is shrinking the size and improving the efficiency of its LED driver components by using thin layers of an iron magnetic alloy and new gallium nitride on silicon devices. Smaller, more efficient components will enable the drivers to be integrated on a single chip, reducing costs. The new semiconductors in Teledyne's drivers can also handle higher levels of power and last longer without sacrificing efficiency. Initial applications for Teledyne's LED power drivers include refrigerated grocery display cases and retail lighting.

  11. Advanced lighting guidelines: 1993. Final report

    SciTech Connect (OSTI)

    Eley, C.; Tolen, T.M. [Eley Associates, San Francisco, CA (United States); Benya, J.R. [Luminae Souter Lighting Design, San Francisco, CA (United States); Rubinstein, F.; Verderber, R. [Lawrence Berkeley Lab., CA (United States)

    1993-12-31T23:59:59.000Z

    The 1993 Advanced Lighting Guidelines document consists of twelve guidelines that provide an overview of specific lighting technologies and design application techniques utilizing energy-efficient lighting practice. Lighting Design Practice assesses energy-efficient lighting strategies, discusses lighting issues, and explains how to obtain quality lighting design and consulting services. Luminaires and Lighting Systems surveys luminaire equipment designed to take advantage of advanced technology lamp products and includes performance tables that allow for accurate estimation of luminaire light output and power input. The additional ten guidelines -- Computer-Aided Lighting Design, Energy-Efficient Fluorescent Ballasts, Full-Size Fluorescent Lamps, Compact Fluorescent Lamps, Tungsten-Halogen Lamps, Metal Halide and HPS Lamps, Daylighting and Lumen Maintenance, Occupant Sensors, Time Scheduling Systems, and Retrofit Control Technologies -- each provide a product technology overview, discuss current products on the lighting equipment market, and provide application techniques. This document is intended for use by electric utility personnel involved in lighting programs, lighting designers, electrical engineers, architects, lighting manufacturers` representatives, and other lighting professionals.

  12. Improving the Efficiency of Solid State Light Sources

    SciTech Connect (OSTI)

    Joanna McKittrick

    2003-03-31T23:59:59.000Z

    This proposal addresses the national need to develop a high efficiency light source for general illumination applications. The goal is to perform research that would lead to the fabrication of a unique solid state, white-emitting light source. This source is based on an InGaN/GaN UV-emitting chip that activates a luminescent material (phosphor) to produce white light. White-light LEDs are commercially available which use UV from a GaN chip to excite a phosphor suspended in epoxy around the chip. Currently, these devices are relatively inefficient. This research will target one technical barrier that presently limits the efficiency of GaN based devices. Improvements in efficiencies will be achieved by improving the internal conversion efficiency of the LED die, by improving the coupling between the die and phosphor(s) to reduce losses at the surfaces, and by selecting phosphors to maximize the emissions from the LEDs in conversion to white light. The UCSD research team proposes for this project to develop new phosphors that have high quantum efficiencies that can be activated by the UV-blue (360-410 nm) light emitted by the GaN device. The main goal for the UCSD team was to develop new phosphor materials with a very specific property: phosphors that could be excited at long UV-wavelengths ({lambda}=350-410 nm). The photoluminescence of these new phosphors must be activated with photons emitted from GaN based dies. The GaN diodes can be designed to emit UV-light in the same range ({lambda}=350-410 nm). A second objective, which is also very important, is to search for alternate methods to fabricate these phosphors with special emphasis in saving energy and time and reduce pollution.

  13. Pore size of FCC pretreat catalyst important

    SciTech Connect (OSTI)

    Moyse, B.M.; Cooper, B.H.

    1985-03-11T23:59:59.000Z

    Conversion of sulfur, nitrogen, and polynuclear aromatics can be optimized by varying catalyst pore dimensions and/or particle size. Increased workload and more exacting performance are demanded from today's fluid catalytic cracking feed pretreat catalysts. The desire to process heavier crudes and the inclusion of visbreaker gas oil, unsaturated fractions like coker gas oils, and even resid, have placed greater emphasis on the importance of selection of those catalysts. Also, some older plants are limited to process conditions and equipment designed for easier feedstocks. Data show that the optimum catalyst pore size for a given application depends not only on the reactivity of the feed, but also on the catalyst's diffusional properties. These properties are also factors which determine whether or not a change in catalyst particle size would be advantageous.

  14. Importance of neutrinoless double beta decay

    E-Print Network [OSTI]

    Utpal Sarkar

    2007-12-17T23:59:59.000Z

    A natural explanation for the smallness of the neutrino mass requires them to be Majorana particles violating lepton number by two units. Since lepton number violation can have several interesting consequences in particle physics and cosmology, it is of utmost importance to find out if there is lepton number violation in nature and what is its magnitude. The neutrinoless double beta decay experiment can answer these questions: if there is lepton number violation and if neutrinos are Majorana particles. In addition, the magnitude of neutrinoless double beta decay will constrain any other lepton number violating processes. This lepton number violation may also be relatd to the matter-antimatter asymmetry of the universe, dark matter and cosmological constant.

  15. Fine particulate chemical composition and light extinction at Meadview, AZ

    SciTech Connect (OSTI)

    Delbert J. Eatough; Wenxuan Cui; Jeffery Hull; Robert J. Farber [Brigham Young University, Provo, UT (United States). Department of Chemistry and Biochemistry

    2006-12-15T23:59:59.000Z

    The concentration of fine particulate nitrate, sulfate, and carbonaceous material was measured for 12-hr daynight samples using diffusion denuder samplers during the Project Measurement of Haze and Visibility Effects (MOHAVE) July to August 1992 Summer Intensive study at Meadview, AZ, just west of Grand Canyon National Park. Organic material was measured by several techniques. Only the diffusion denuder method measured the semivolatile organic material. Fine particulate sulfate and nitrate (using denuder technology) determined by various groups agreed. Based on the various collocated measurements obtained during the Project MOHAVE study, the precision of the major fine particulate species was {+-} 0.6 {mu}g/m{sup 3} organic material, {+-} 0.3 {mu}g/m{sup 3} ammonium sulfate, and {+-} 0.07 {mu}g/m{sup 3} ammonium nitrate. Fine particulate organic material was the principal particulate contributor to light extinction during the study period, with fine particulate sulfate as the second most important contributor. Particle light extinction was dominated by sulfate and organic material during periods of lowest light extinction. Combination of the extinction data and chemical mass balance analysis of sulfur oxides sources in the region indicate that the major anthropogenic contributors to light extinction were from the Los Angeles, CA, and Las Vegas, NV, urban areas. Mohave Power Project associated secondary sulfate was a negligible contributor to light extinction. 49 refs., 12 figs., 7 tabs.

  16. Breaking the light speed barrier

    E-Print Network [OSTI]

    O. I. Chashchina; Z. K. Silagadze

    2012-10-09T23:59:59.000Z

    As it is well known, classical special relativity allows the existence of three different kinds of particles: bradyons, luxons and tachyons. Bradyons have non-zero mass and hence always travel slower than light. Luxons are particles with zero mass, like the photon, and they always travel with invariant velocity. Tachyons are hypothetical superluminal particles that always move faster than light. The existence of bradyons and luxons is firmly established, while the tachyons were never reliably observed. In quantum field theory, the appearance of tachyonic degrees of freedom indicates vacuum instability rather than a real existence of the faster-than-light particles. However, recent controversial claims of the OPERA experiment about superluminal neutrinos triggered a renewed interest in superluminal particles. Driven by a striking analogy of the old Frenkel-Kontorova model of a dislocation dynamics to the theory of relativity, we conjecture in this note a remarkable possibility of existence of the fourth type of particles, elvisebrions, which can be superluminal. The characteristic feature of elvisebrions, distinguishing them from tachyons, is that they are outside the realm of special relativity and their energy remains finite (or may even turn to zero) when the elvisebrion velocity approaches the light velocity.

  17. The light meson spectroscopy program

    SciTech Connect (OSTI)

    Smith, Elton S. [JLAB

    2014-06-01T23:59:59.000Z

    Recent discoveries of a number of unexpected new charmomium-like meson states at the BaBar and Belle B-factories have demonstrated how little is still known about meson spectroscopy. In this talk we will review recent highlights of the light quark spectroscopy from collider and fixed target experiments.

  18. MANDATORY MEASURES OUTDOOR LIGHTING CONTROLS

    E-Print Network [OSTI]

    California at Davis, University of

    EXTERIOR SPACES COMPLY WITH TITLE 24 There are two major steps for exterior spaces to comply with Title 24 for exterior space. A space complies with these requirements if the actual lighting power used in the space. Backlight Backlight includes all illumination that is in the space between the ground and 80 degrees above

  19. Slow light enhanced photon echoes

    E-Print Network [OSTI]

    J. Hahn; B. S. Ham

    2009-09-28T23:59:59.000Z

    We report a slow light-enhanced photon echo method, whose retrieval efficiency is two orders of magnitude higher than that of conventional photon echoes. The enhanced photon echo efficiency is due to lengthened interaction time given by ultraslow group velocity.

  20. Metacapacitors for LED Lighting: Metacapacitors

    SciTech Connect (OSTI)

    None

    2010-09-02T23:59:59.000Z

    ADEPT Project: The CUNY Energy Institute is developing less expensive, more efficient, smaller, and longer-lasting power converters for energy-efficient LED lights. LEDs produce light more efficiently than incandescent lights and last significantly longer than compact fluorescent bulbs, but they require more sophisticated power converter technology, which increases their cost. LEDs need more sophisticated converters because they require a different type of power (low voltage direct current, or DC) than what's generally supplied by power outlets. The CUNY Energy Institute is developing sophisticated power converters for LEDs that contain capacitors made from new, nanoscale materials. Capacitors are electrical components that are used to store energy. CUNY's unique capacitors are configured with advanced power circuits to more efficiently control and convert power to the LED lighting source. They also eliminate the need for large magnetic components, instead relying on networks of capacitors that can be easily printed on plastic substrate. CUNY's prototype LED power converter already meets DOE's 2020 projections for the energy efficiency of LED power converters.

  1. Covered Product Category: Exterior Lighting

    Broader source: Energy.gov [DOE]

    The Federal Energy Management Program (FEMP) provides acquisition guidance and Federal efficiency requirements for outdoor wall-mounted light fixtures or luminaires, outdoor pole/arm-mounted area and roadway luminaires, outdoor pole/arm-mounted decorative luminaires, fuel pump canopy luminaires, bollards, and parking garage luminaires, all of which are FEMP-designated product categories.

  2. High Performance Outdoor Lighting Accelerator

    Broader source: Energy.gov [DOE]

    Hosted by the U.S. Department of Energy (DOE)’s Weatherization and Intergovernmental Programs Office (WIPO), this webinar covered the expansion of the Better Buildings platform to include the newest initiative for the public sector: the High Performance Outdoor Lighting Accelerator (HPOLA).

  3. National Synchrotron Light Source II

    ScienceCinema (OSTI)

    Steve Dierker

    2010-01-08T23:59:59.000Z

    The National Synchrotron Light Source II (NSLS-II) at the U.S. Department of Energy's Brookhaven National Laboratory is a proposed new state-of-the-art medium energy storage ring designed to deliver world-leading brightness and flux with top-off operation

  4. Theory in Biology available light

    E-Print Network [OSTI]

    Nowak, Martin A.

    Magazine R406 Theory in Biology Theory is available light Martin A. Nowak Many people praise Gregor the neutral theory of evolution, which assumes that the overwhelming majority of molecular mutations do assume the neutral theory is correct. In a brilliant PhD thesis submitted in 1964, Bill Hamilton

  5. Enhanced coupling of light from organic light emitting diodes using nanoporous films

    E-Print Network [OSTI]

    Enhanced coupling of light from organic light emitting diodes using nanoporous films H. J. Peng, Y the light extraction efficiency for organic light emitting diode OLED . Nanoporous alumina film was used by Bragg scattering. The corrugated light- emitting diode had two-times the efficiency as compared

  6. CSC418 / CSCD18 / CSC2504 Basic Lighting and Reflection 8 Basic Lighting and Reflection

    E-Print Network [OSTI]

    Toronto, University of

    CSC418 / CSCD18 / CSC2504 Basic Lighting and Reflection 8 Basic Lighting and Reflection Up things, on the lighting that illuminates the scene, and on the interaction of light with the objects in the scene. Some of the basic qualitative properties of lighting and object reflectance that we need

  7. Light Collages: Lighting Design for Effective Visualization Chang Ha Lee Xuejun Hao Amitabh Varshney

    E-Print Network [OSTI]

    Varshney, Amitabh

    Light Collages: Lighting Design for Effective Visualization Chang Ha Lee Xuejun Hao Amitabh 20742 {chlee, hao, varshney}@cs.umd.edu ABSTRACT We introduce Light Collages ­ a lighting design system perception of features with lighting that is locally consistent and globally inconsistent. Inspired

  8. Light extraction efficiency enhancement of InGaN quantum wells light-emitting diodes with

    E-Print Network [OSTI]

    Gilchrist, James F.

    Light extraction efficiency enhancement of InGaN quantum wells light-emitting diodes@lehigh.edu Abstract: Improvement of light extraction efficiency of InGaN light emitting diodes (LEDs) using microstructures on the light extraction efficiency of III-Nitride LEDs was studied. Depending on the size

  9. LightSlice: Matrix Slice Sampling for the Many-Lights Problem Dartmouth College

    E-Print Network [OSTI]

    Pellacini, Fabio

    LightSlice: Matrix Slice Sampling for the Many-Lights Problem Jiawei Ou Dartmouth College Fabio Pellacini Dartmouth College Figure 1: The light transport matrices of two complex scenes (subsampled from algorithm, LightSlice, effectively exploits these typical structures of light transport matrices

  10. Light is said to be reflected when the angle at which light

    E-Print Network [OSTI]

    Gilbes, Fernando

    1 #12;2 Light is said to be reflected when the angle at which light initially strikes a surface is equal to the angle at which light bounces off the same surface. In the diagram, light strikes a surface", this is an example of reflected light. Refraction is the bending of a wave when it enters a medium where it's speed

  11. Legislative Directive: EISA 2007, Subtitle B: Lighting Energy Efficiency

    Broader source: Energy.gov [DOE]

    Legislative Directive: EISA 2007, Subtitle B: Lighting Energy Efficiency, Sec. 321: Lighting Energy Efficiency

  12. Electron Beam Collimation for the Next Generation Light Source

    SciTech Connect (OSTI)

    Steier, C.; Emma, P.; Nishimura, H.; Papadopoulos, C.; Sannibale, F.

    2013-05-20T23:59:59.000Z

    The Next Generation Light Source will deliver high (MHz) repetition rate electron beams to an array of free electron lasers. Because of the significant average current in such a facility, effective beam collimation is extremely important to minimize radiation damage to undulators, prevent quenches of superconducting cavities, limit dose rates outside of the accelerator tunnel and prevent equipment damage. This paper describes the early conceptual design of a collimation system, as well as initial results of simulations to test its effectiveness.

  13. Africa gaining importance in world LPG trade

    SciTech Connect (OSTI)

    Haun, R.R. [Purvin and Gertz Inc., Dallas, TX (United States); Otto, K.W.; Whitley, S.C. [Purvin and Gertz Inc., Houston, TX (United States)

    1997-05-12T23:59:59.000Z

    Major LPG projects planned or under way in Africa will increase the importance of that region`s presence in world LPG trade. Supplies will nearly double between 1995 and 2005, at which time they will remain steady for at least 10 years. At the same time that exports are leveling, however, increasing domestic demand for PG is likely to reduce export-market participation by Algeria, Nigeria, Egypt, and Libya. The growth of Africa`s participation in world LPG supply is reflected in comparisons for the next 15--20 years. Total world supply of LPG in 1995 was about 165 million metric tons (tonnes), of which Africans share was 7.8 million tonnes. By 2000, world supply will grow to slightly more than 200 million tonnes, with Africa`s share expected to increase to 13.2 million tonnes (6.6%). And by 2005, world LPG supply will reach nearly 230 million tonnes; Africa`s overall supply volumes by that year will be nearly 16.2 million tonnes (7%). World LPG supply for export in 1995 was on order of 44 million tonnes with Africa supply about 4 million tonnes (9%). By 2005, world export volumes of LPG will reach nearly 70 million tonnes; Africa`s share will have grown by nearly 10 million tonnes (14.3%).

  14. Monitored lighting energy savings from dimmable lighting controls in The New York Times Headquarters Building

    E-Print Network [OSTI]

    Fernandes, Luis L.

    2014-01-01T23:59:59.000Z

    A. , D’Herdt, P. , 2008, Lighting energy savings in officesLux Europa, 11 th European Lighting Conference, Istanbul,evaluation of the dimmable lighting, automated shading, and

  15. LIGHTING RESEARCH PROGRAM Project 5.4 DALI Lighting Control Device Standard

    E-Print Network [OSTI]

    LIGHTING RESEARCH PROGRAM Project 5.4 DALI Lighting Control Device Standard Development FINAL CONTROL DEVICE STANDARD PROPOSED BY NEMA ......10 TECHNICAL ASSESSMENT REPORT Electronics Co.; Al Lombardi, Leviton Manufacturing Co., Inc.; Mike Stein, Universal Lighting Technologies

  16. Light extraction enhanced white light-emitting diodes with multi-layered phosphor configuration

    E-Print Network [OSTI]

    You, Jiun Pyng; Tran, Nguyen T.; Shi, Frank G.

    2010-01-01T23:59:59.000Z

    and J. K. Kim, “Solid-state light sources getting smart,”power phosphor-converted light-emitting diodes based on III-for phosphor- based white-light-emitting diodes,” Appl.

  17. Lighting system with thermal management system

    DOE Patents [OSTI]

    Arik, Mehmet; Weaver, Stanton; Stecher, Thomas; Seeley, Charles; Kuenzler, Glenn; Wolfe, Jr., Charles; Utturkar, Yogen; Sharma, Rajdeep; Prabhakaran, Satish; Icoz, Tunc

    2013-05-07T23:59:59.000Z

    Lighting systems having unique configurations are provided. For instance, the lighting system may include a light source, a thermal management system and driver electronics, each contained within a housing structure. The light source is configured to provide illumination visible through an opening in the housing structure. The thermal management system is configured to provide an air flow, such as a unidirectional air flow, through the housing structure in order to cool the light source. The driver electronics are configured to provide power to each of the light source and the thermal management system.

  18. Fact #837: September 8, 2014 Gap between Net Imports and Total Imports of Petroleum is Widening – Dataset

    Broader source: Energy.gov [DOE]

    Excel file with dataset for Fact #837: Gap between Net Imports and Total Imports of Petroleum is Widening

  19. Importance of energy efficiency in office equipment

    SciTech Connect (OSTI)

    Blatt, M.H.

    1995-12-01T23:59:59.000Z

    Energy-Efficient Office Technology 1994: An International Seminar has been organized and funded by the Office Technology Efficiency Consortium, a group of utilities, government agencies, and other energy efficiency advocates that has been aggressively championing the need for more efficient computers, displays, printers, faxes, and copiers. The Consortium, organized in late 1992, currently consists of 10 cofunders and numerous other participants. The cofunders are: The Electric Power Research Institute, New York State Energy Research and Development Authority, Consolidated Edison Company of New York, the Swedish National Board for Industrial and Technical Development (NUTEK), Ontario Hydro, Pacific Gas and Electric Company, U.S. Department of Energy, U.S. Environmental Protection Agency, and the Wisconsin Center for Demand-Side Research. The Consortium has been striving to achieve multiple objectives. These objectives are to: (1) Improve office technology user energy efficiency end operating cost (2) Improve end-use equipment`s power quality characteristics (3) Increase equipment immunity to power line disturbances (4) Avoid the need for wiring overloads and upgrades (5) Reduce utility`s peak demand (6) Improve utility load factor. The growth in electricity use in the United States and the need for additional utility capacity has been driven to a great extent by the U.S. shift to a service economy and the coincident increase in the use of office equipment in these service establishments. The initial efforts of the Consortium, which consisted of the cofunders, included holding a workshop in June 1992 to heighten awareness of the importance of the need for more efficient office equipment. The workshop was documented in {open_quotes}Proceedings: Energy-Efficient Office Technologies,{close_quotes} TR-101945, in December 1992.

  20. Compton Scattering on Light Nuclei

    E-Print Network [OSTI]

    Deepshikha Shukla

    2009-12-22T23:59:59.000Z

    Compton scattering on light nuclei ($A=2,3$) has emerged as an effective avenue to search for signatures of neutron polarizabilities, both spin--independent and spin--dependent ones. In this discussion I will focus on the theoretical aspect of Compton scattering on light nuclei; giving first a brief overview and therafter concentrating on our Compton scattering calculations based on Chiral effective theory at energies of the order of pion mass. These elastic $\\gamma$d and $\\gamma$He-3 calculations include nucleons, pions as the basic degrees of freedom. I will also discuss $\\gamma$d results where the $\\Delta$-isobar has been included explicitly. Our results on unpolarized and polarization observables suggest that a combination of experiments and further theoretical efforts will provide an extraction of the neutron polarizabilities.

  1. Variable area light reflecting assembly

    DOE Patents [OSTI]

    Howard, T.C.

    1986-12-23T23:59:59.000Z

    Device is described for tracking daylight and projecting it into a building. The device tracks the sun and automatically adjusts both the orientation and area of the reflecting surface. The device may be mounted in either a wall or roof of a building. Additionally, multiple devices may be employed in a light shaft in a building, providing daylight to several different floors. The preferred embodiment employs a thin reflective film as the reflecting device. One edge of the reflective film is fixed, and the opposite end is attached to a spring-loaded take-up roller. As the sun moves across the sky, the take-up roller automatically adjusts the angle and surface area of the film. Additionally, louvers may be mounted at the light entrance to the device to reflect incoming daylight in an angle perpendicular to the device to provide maximum reflective capability when daylight enters the device at non-perpendicular angles. 9 figs.

  2. Variable area light reflecting assembly

    DOE Patents [OSTI]

    Howard, Thomas C. (Raleigh, NC)

    1986-01-01T23:59:59.000Z

    Device for tracking daylight and projecting it into a building. The device tracks the sun and automatically adjusts both the orientation and area of the reflecting surface. The device may be mounted in either a wall or roof of a building. Additionally, multiple devices may be employed in a light shaft in a building, providing daylight to several different floors. The preferred embodiment employs a thin reflective film as the reflecting device. One edge of the reflective film is fixed, and the opposite end is attached to a spring-loaded take-up roller. As the sun moves across the sky, the take-up roller automatically adjusts the angle and surface area of the film. Additionally, louvers may be mounted at the light entrance to the device to reflect incoming daylight in an angle perpendicular to the device to provide maximum reflective capability when daylight enters the device at non-perpendicular angles.

  3. Porous light-emitting compositions

    DOE Patents [OSTI]

    Burrell, Anthony K. (Los Alamos, NM); McCleskey, Thomas Mark (Los Alamos, NM); Jia, Quanxi (Los Alamos, NM); Bauer, Eve (Los Alamos, NM); Mueller, Alexander H. (Los Alamos, NM)

    2012-04-17T23:59:59.000Z

    Light-emitting devices are prepared by coating a porous substrate using a polymer-assisted deposition process. Solutions of metal precursor and soluble polymers having binding properties for metal precursor were coated onto porous substrates. The coated substrates were heated at high temperatures under a suitable atmosphere. The result was a substrate with a conformal coating that did not substantially block the pores of the substrate.

  4. Light shield for solar concentrators

    DOE Patents [OSTI]

    Plesniak, Adam P.; Martins, Guy L.

    2014-08-26T23:59:59.000Z

    A solar receiver unit including a housing defining a recess, a cell assembly received in the recess, the cell assembly including a solar cell, and a light shield received in the recess and including a body and at least two tabs, the body defining a window therein, the tabs extending outward from the body and being engaged with the recess, wherein the window is aligned with the solar cell.

  5. Broadband light-emitting diode

    DOE Patents [OSTI]

    Fritz, Ian J. (Albuquerque, NM); Klem, John F. (Sandia Park, NM); Hafich, Michael J. (Albuquerque, NM)

    1998-01-01T23:59:59.000Z

    A broadband light-emitting diode. The broadband light-emitting diode (LED) comprises a plurality of III-V compound semiconductor layers grown on a semiconductor substrate, with the semiconductor layers including a pair of cladding layers sandwiched about a strained-quantum-well active region having a plurality of different energy bandgaps for generating light in a wavelength range of about 1.3-2 .mu.m. In one embodiment of the present invention, the active region may comprise a first-grown quantum-well layer and a last-grown quantum-well layer that are oppositely strained; whereas in another embodiment of the invention, the active region is formed from a short-period superlattice structure (i.e. a pseudo alloy) comprising alternating thin layers of InGaAs and InGaAlAs. The use a short-period superlattice structure for the active region allows different layers within the active region to be simply and accurately grown by repetitively opening and closing one or more shutters in an MBE growth apparatus to repetitively switch between different growth states therein. The broadband LED may be formed as either a surface-emitting LED or as an edge-emitting LED for use in applications such as chemical sensing, fiber optic gyroscopes, wavelength-division-multiplexed (WDM) fiber-optic data links, and WDM fiber-optic sensor networks for automobiles and aircraft.

  6. Broadband light-emitting diode

    DOE Patents [OSTI]

    Fritz, I.J.; Klem, J.F.; Hafich, M.J.

    1998-07-14T23:59:59.000Z

    A broadband light-emitting diode is disclosed. The broadband light-emitting diode (LED) comprises a plurality of III-V compound semiconductor layers grown on a semiconductor substrate, with the semiconductor layers including a pair of cladding layers sandwiched about a strained-quantum-well active region having a plurality of different energy bandgaps for generating light in a wavelength range of about 1.3--2 {micro}m. In one embodiment of the present invention, the active region may comprise a first-grown quantum-well layer and a last-grown quantum-well layer that are oppositely strained; whereas in another embodiment of the invention, the active region is formed from a short-period superlattice structure (i.e. a pseudo alloy) comprising alternating thin layers of InGaAs and InGaAlAs. The use a short-period superlattice structure for the active region allows different layers within the active region to be simply and accurately grown by repetitively opening and closing one or more shutters in an MBE growth apparatus to repetitively switch between different growth states therein. The broadband LED may be formed as either a surface-emitting LED or as an edge-emitting LED for use in applications such as chemical sensing, fiber optic gyroscopes, wavelength-divisionmultiplexed (WDM) fiber-optic data links, and WDM fiber-optic sensor networks for automobiles and aircraft. 10 figs.

  7. Materials for solid state lighting

    SciTech Connect (OSTI)

    Johnson, S.G.; Simmons, J.A.

    2002-03-26T23:59:59.000Z

    Dramatic improvement in the efficiency of inorganic and organic light emitting diodes (LEDs and OLEDs) within the last decade has made these devices viable future energy efficient replacements for current light sources. However, both technologies must overcome major technical barriers, requiring significant advances in material science, before this goal can be achieved. Attention will be given to each technology associated with the following major areas of material research: (1) material synthesis, (2) process development, (3) device and defect physics, and (4) packaging. The discussion on material synthesis will emphasize the need for further development of component materials, including substrates and electrodes, necessary for improving device performance. The process technology associated with the LEDs and OLEDs is very different, but in both cases it is one factor limiting device performance. Improvements in process control and methodology are expected to lead to additional benefits of higher yield, greater reliability and lower costs. Since reliability and performance are critical to these devices, an understanding of the basic physics of the devices and device failure mechanisms is necessary to effectively improve the product. The discussion will highlight some of the more basic material science problems remaining to be solved. In addition, consideration will be given to packaging technology and the need for the development of novel materials and geometries to increase the efficiencies and reliability of the devices. The discussion will emphasize the performance criteria necessary to meet lighting applications, in order to illustrate the gap between current status and market expectations for future product.

  8. THELUMINAPROJECT http://light.lbl.gov

    E-Print Network [OSTI]

    Jacobson, Arne

    into the broader off-grid lighting market. The lead acid batteries embedded in flashlights also represent, and it may also indicate the onset of a broader market spoiling effect for off-grid lighting products based

  9. Embodied Energy and Off-Grid Lighting

    E-Print Network [OSTI]

    Alstone, Peter

    2012-01-01T23:59:59.000Z

    Life Cycle Assessment of Off-Grid Lighting Applications:Testing for Emerging Off-grid White-LED Illumination SystemsBudget: The Economics of Off-Grid Lighting for Small

  10. Overcoming Common Pitfalls: Energy Efficient Lighting Projects...

    Broader source: Energy.gov (indexed) [DOE]

    require light levels to go off after 2 am. This regular series would be easily set. Daylight based controls use sensors to figure out when more light is needed. Photo cells are...

  11. Energy 101: Lighting Choices | Department of Energy

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    in your home to energy-saving incandescent, compact fluorescent lamp (CFL), or light emitting diode (LED) bulbs could save you about 50 per year. For more information on lighting...

  12. Outdoor Solar Lighting | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    place the lights in a sunny location. Others have the lights separate from a solar cell panel, in which case only the panel needs to be placed in a sunny location. Units vary in...

  13. Portable lamp with dynamically controlled lighting distribution

    DOE Patents [OSTI]

    Siminovitch, Michael J. (Pinole, CA); Page, Erik R. (Berkeley, CA)

    2001-01-01T23:59:59.000Z

    A double lamp table or floor lamp lighting system has a pair of compact fluorescent lamps (CFLs) arranged vertically with a reflective septum in between. By selectively turning on one or both of the CFLs, down lighting, up lighting, or both up and down lighting is produced. The control system can also vary the light intensity from each CFL. The reflective septum insures that almost all the light produced by each lamp will be directed into the desired light distribution pattern which is selected and easily changed by the user. Planar compact fluorescent lamps, e.g. circular CFLs, particularly oriented horizontally, are preferable. CFLs provide energy efficiency. The lighting system may be designed for the home, hospitality, office or other environments.

  14. Sandia National Laboratories: Solid-State Lighting

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Solid-State Lighting InAs Quantum Dot Transitions On April 5, 2011, in EC, Energy, Energy Efficiency, News, Solid-State Lighting March 1, 2011singlepic id364 w320 h240...

  15. Sandia Energy - Lighting Developments to 2030

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    to 2030Tara Camacho-Lopez2015-05-14T14:32:00+00:00 Lighting Technologies, Costs, and Energy Demand: Global Developments to 2030 View Slides: Lighting Technologies, Costs, and...

  16. Kansas City Power & Light- Solar PV Rebates

    Broader source: Energy.gov [DOE]

    Kansas City Power and Light and its affiliate Kansas City Power and Light Greater Missouri Operations (collectively referred to as KCP&L) offer rebates to their customers for the installation...

  17. Text-Alternative Version LED Lighting Forecast

    Broader source: Energy.gov [DOE]

    The DOE report Energy Savings Forecast of Solid-State Lighting in General Illumination Applications estimates the energy savings of LED white-light sources over the analysis period of 2013 to 2030....

  18. Webcast: Evaluating LED Street Lighting Solutions

    Broader source: Energy.gov [DOE]

    In this July 20, 2010 webcast, Edward Smalley of Seattle City Light provided an update on DOE Municipal Solid-State Street Lighting Consortium activities. The webcast also presented perspectives...

  19. Apparatus for shifting the wavelength of light

    DOE Patents [OSTI]

    McCulla, William H. (Oak Ridge, TN); Allen, Jr., John D. (Knoxville, TN)

    1983-01-01T23:59:59.000Z

    A light beam is reflected back and forth between a rotating body having a retroreflection corner at opposite ends thereof and a fixed mirror to change the wavelength of the light beam by the Doppler effect.

  20. Lumens and the Lighting Facts Label

    Broader source: Energy.gov [DOE]

    When you're shopping for lightbulbs, compare lumens and use the Lighting Facts label to be sure you're getting the amount of light, or level of brightness, you want.

  1. Lighting system with heat distribution face plate

    DOE Patents [OSTI]

    Arik, Mehmet; Weaver, Stanton Earl; Stecher, Thomas Elliot; Kuenzler, Glenn Howard; Wolfe, Jr., Charles Franklin; Li, Ri

    2013-09-10T23:59:59.000Z

    Lighting systems having a light source and a thermal management system are provided. The thermal management system includes synthetic jet devices, a heat sink and a heat distribution face plate. The synthetic jet devices are arranged in parallel to one and other and are configured to actively cool the lighting system. The heat distribution face plate is configured to radially transfer heat from the light source into the ambient air.

  2. Reflections and Thoughts on Tired Light

    E-Print Network [OSTI]

    M. Moore; J. Dunning-Davies

    2007-07-23T23:59:59.000Z

    The position of the various tired light theories is reviewed briefly and it is noted that one of the biggest objections to them concerns the mechanism by which light might lose energy as it travels through space. Here some new work relating to the constancy of the speed of light is highlighted as providing a possible solution to this conundrum, thus making more feasible explanation of phenomena via theories involving the notion of tired light.

  3. Considering LEDs for Street and Area Lighting

    Broader source: Energy.gov [DOE]

    View Jim Brodrick's keynote video from the September 2009 IES Street and Area Lighting Conference in Philadelphia.

  4. Lighting the Way with Compact Fluorescent Lighting | Department of Energy

    Energy Savers [EERE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directed off Energy.gov. Are you sure you wantJoin us for #SpaceWeek Join us for #SpaceWeekDepartmentLight

  5. Types of Lighting in Commercial Buildings - Lighting Types

    Gasoline and Diesel Fuel Update (EIA)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 111 1,613 122 40 Buildingto17 34 44Year Jan Feb Mar Apr May Jun602 1,397 125 Q 69ChangesLighting

  6. Peninsula Light Company PenLight | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are being directedAnnual SiteofEvaluatingGroup |JilinLuOpenNorthOlympiaAnalysis)Pearl River ValleyPeninsula Light

  7. Light Trapping for High Efficiency Heterojunction Crystalline Si Solar Cells: Preprint

    SciTech Connect (OSTI)

    Wang, Q.; Xu, Y.; Iwaniczko, E.; Page, M.

    2011-04-01T23:59:59.000Z

    Light trapping plays an important role to achieve high short circuit current density (Jsc) and high efficiency for amorphous/crystalline Si heterojunction solar cells. Si heterojunction uses hydrogenated amorphous Si for emitter and back contact. This structure of solar cell posses highest open circuit voltage of 0.747 V at one sun for c-Si based solar cells. It also suggests that over 25% record-high efficiency is possible with further improvement of Jsc. Light trapping has two important tasks. The first one is to reduce the surface reflectance of light to zero for the solar spectrum that Si has a response. The second one is to increase the effective absorption length to capture all the photon. For Si heterojunction solar cell, surface texturing, anti-reflectance indium tin oxides (ITO) layer at the front and back are the key area to improve the light trapping.

  8. Bayesian surface estimation for white light interferometry

    E-Print Network [OSTI]

    Hamprecht, Fred A.

    .hamprecht@iwr.uni-heidelberg.de). 1 #12;The development of white light interferometers for industry was first guidedBayesian surface estimation for white light interferometry Michael Hissmann Fred A. Hamprecht 2004/07/05 Abstract In conventional white light interferometry (WLI) surface estimation, data acquisition is followed

  9. Energy-efficient lighting system for television

    DOE Patents [OSTI]

    Cawthorne, Duane C. (Amarillo, TX)

    1987-07-21T23:59:59.000Z

    A light control system for a television camera comprises an artificial light control system which is cooperative with an iris control system. This artificial light control system adjusts the power to lamps illuminating the camera viewing area to provide only sufficient artificial illumination necessary to provide a sufficient video signal when the camera iris is substantially open.

  10. THELUMINAPROJECT http://light.lbl.gov

    E-Print Network [OSTI]

    Jacobson, Arne

    THELUMINAPROJECT http://light.lbl.gov The Lumina Project includes an Off-Grid Lighting Technology of off-grid lighting solutions for the developing world. Periodic Research Notes present new results vary depending on the intensity of use patterns. To avoid a potential market spoiling effect for off-grid

  11. Solid State Lighting ECE 198 Lab Manual

    E-Print Network [OSTI]

    Wasserman, Daniel M.

    will take the role of a consultant to either a large company, a government institution, or an academic A significant fraction of the electricity used in this country is used for lighting applications, whether countries require sources of light, there has been a significant increase in light consumption globally

  12. STATE OF CALIFORNIA OUTDOOR LIGHTING WORKSHEET

    E-Print Network [OSTI]

    STATE OF CALIFORNIA OUTDOOR LIGHTING WORKSHEET CEC-OLTG-2C (Revised 03/10) CALIFORNIA ENERGY COMMISSION 2008 Nonresidential Compliance Forms March 2010 OUTDOOR LIGHTING WORKSHEET (Page 1 of 3) OLTG-2C Project Name: Date: A. LIGHTING POWER ALLOWANCE FOR GENERAL HARDSCAPE AREA WATTAGE ALLOWANCE (AWA) LINEAR

  13. Tabletop Computed Lighting for Practical Digital Photography

    E-Print Network [OSTI]

    Tabletop Computed Lighting for Practical Digital Photography Ankit Mohan, Reynold Bailey, Jonathan Abstract--We apply simplified image-based lighting methods to reduce the equipment, cost, time, and specialized skills required for high-quality photographic lighting of desktop-sized static objects

  14. Sphere Light Field Rendering Zigang Wang1

    E-Print Network [OSTI]

    Sphere Light Field Rendering Zigang Wang1 and Zhengrong Liang1,2 Departments of Radiology1 and Computer Science2 , State University of New York, Stony Brook, NY 11794, USA ABSTRACT Light field algorithm is one of the most famous image-based rendering techniques. In this paper, an improved light field

  15. Illumination of Polygons with Vertex Lights

    E-Print Network [OSTI]

    Urrutia, Jorge

    * Illumination of Polygons with Vertex Lights Vladimir Estivill­Castro a , Joseph O'Rourke b;1 less than ß suffices for all polygons. A vertex floodlight of angle ff is an internal cone of light ff is a light that projects in a (contiguous) cone of angle at most ff. A floodlight placed

  16. Light Sources on the Nylon Vessels' Surfaces

    E-Print Network [OSTI]

    Chapter 7 Light Sources on the Nylon Vessels' Surfaces The nylon vessels are justifiably the most the IV. A set of light diffusers has been placed on pre-defined points of both vessels. These are attached to the tip of an optical fiber that carries light from a source outside the WT (LED 184 #12

  17. LED Light Sources for Projection Display Applications

    E-Print Network [OSTI]

    Palffy-Muhoray, Peter

    LED Light Sources for Projection Display Applications By Chenhui Peng 04-13-2012 #12;Outline · 1. · The first practical LED is in red color and it is made with gallium arsenide (GaAs). 4http://en.wikipedia.org/wiki/Light with holes and release energy in the form of photons. 5http://en.wikipedia.org/wiki/Light-emitting_diode #12

  18. (Revised May 25, 2012) Interference of Light

    E-Print Network [OSTI]

    Collins, Gary S.

    (Revised May 25, 2012) Interference of Light WARNING: Use the laser SAFELY. Do not look directly) To observe the interference patterns for laser light passing through a single narrow slit, through two. (2) To determine by graphical techniques the wavelength of the laser light based on the observed

  19. Retail Lighting: Title 24 & Technology Update

    E-Print Network [OSTI]

    California at Davis, University of

    Retail Lighting: Title 24 & Technology Update Kelly Cunningham Outreach Director kcunning@ucdavis.edu California Lighting Technology Center, UC Davis RESEARCH . INNOVATION . PARTNERSHIP Supporting compliance Lighting: Title 24 and Technology Update C00005 Kelly Cunningham April 24,2014 #12;Credit(s) earned

  20. Solid State Lighting Semiconductor Spectroscopy & Devices

    E-Print Network [OSTI]

    Strathclyde, University of

    and fluorescent lamps, are very inefficient in transforming energy into light. Due to upcoming problems in energy % of Earth's total power consumption is used for lighting! Figure 3: Earth at night from space. Evolution inside a semiconductor for light emission. Over 150 years ago... How to achieve white LEDs? Figure 5

  1. Lighting market sourcebook for the US

    SciTech Connect (OSTI)

    Vorsatz, D.; Shown, L.; Koomey, J.; Moezzi, M.; Denver, A.; Atkinson, B.

    1997-12-01T23:59:59.000Z

    Throughout the United States, in every sector and building type, lighting is a significant electrical end-use. Based on the many and varied studies of lighting technologies, and experience with programs that promote lighting energy-efficiency, there is a significant amount of cost-effective energy savings to be achieved in the lighting end use. Because of such potential savings, and because consumers most often do not adopt cost-effective lighting technologies on their own, programs and policies are needed to promote their adoption. Characteristics of lighting energy use, as well as the attributes of the lighting marketplace, can significantly affect the national pattern of lighting equipment choice and ownership. Consequently, policy makers who wish to promote energy-efficient lighting technologies and practices must understand the lighting technologies that people use, the ways in which they use them, and marketplace characteristics such as key actors, product mix and availability, price spectrum, and product distribution channels. The purpose of this report is to provide policy-makers with a sourcebook that addresses patterns of lighting energy use as well as data characterizing the marketplace in which lighting technologies are distributed, promoted, and sold.

  2. The Unbearable Lightness of Being Department of

    E-Print Network [OSTI]

    Karczmarek, Joanna

    & Astronomy #12;Scott Oser The Unbearable Lightness of Being (A Neutrino) 2 Outline 1. What's a neutrino? 2 the world of experiment 6. Conclusions #12;Scott Oser The Unbearable Lightness of Being (A Neutrino) 3 Chapter 1: What's a neutrino? #12;Scott Oser The Unbearable Lightness of Being (A Neutrino) 4 The Building

  3. Smart Lighting ERC Industrial Speaker Series

    E-Print Network [OSTI]

    Lü, James Jian-Qiang

    . Stough Director of Solid State Lighting Research Osram Sylvania Abstract: For the past five years or so fixture, etc.), and present problems for the Lighting Company trying to implement LED-based lighting them as the next `filament." Bio: Dr. Matthew Stough is the director of research in Solid-State

  4. Waste Toolkit A-Z Light bulbs

    E-Print Network [OSTI]

    Melham, Tom

    Waste Toolkit A-Z Light bulbs Can I recycle light bulbs? It depends what type of bulbs you have of in the normal University waste bins (landfill waste). Energy saving bulbs and fluorescent tubes are classified light bulbs? Standard filament bulbs Put in the waste bin (landfill waste) as these are not classified

  5. Energy Conversion: Solid-State Lighting

    E-Print Network [OSTI]

    8 Energy Conversion: Solid-State Lighting E. Kioupakis1,2 , P. Rinke1,3 , A. Janotti1 , Q. Yan1 fraction of the world's energy resources [1]. Lighting has been one of the earliest applications. The inefficiency of existing light sources that waste most of the power they consume is the reason for this large

  6. Evaluation of daytime vs. nighttime red-light-running using an advanced warning for end of green phase system

    E-Print Network [OSTI]

    Obeng-Boampong, Kwaku Oduro

    2005-11-01T23:59:59.000Z

    The problem of dilemma zone protection and red-light-running is especially important in certain rural intersections due to the higher speeds at these intersections and their isolated nature. In addition, the presence of a larger percentage...

  7. Low-cost, deterministic quasi-periodic photonic structures for light trapping in thin film silicon solar cells

    E-Print Network [OSTI]

    Sheng, Xing

    Light trapping has been an important issue for thin film silicon solar cells because of the low absorption coefficient in the near infrared range. In this paper, we present a photonic structure which combines anodic aluminum ...

  8. Evidence for photoacclimation by the diatom Chaetoceros muelleri due to fluctuating light Oregon State University REU 2007

    E-Print Network [OSTI]

    Kurapov, Alexander

    of marine microalgae is important due to their significant contributions to the global environment.Introduction #12;Prier 2 Microalgae are commonly defined as aquatic photoautotrophic microbes resources (irradiance) to convert light into chemical energy through the process of photosynthesis

  9. Twist Field as Three String Interaction Vertex in Light Cone String Field Theory

    E-Print Network [OSTI]

    Isao Kishimoto; Sanefumi Moriyama; Shunsuke Teraguchi

    2007-03-22T23:59:59.000Z

    It has been suggested that matrix string theory and light-cone string field theory are closely related. In this paper, we investigate the relation between the twist field, which represents string interactions in matrix string theory, and the three-string interaction vertex in light-cone string field theory carefully. We find that the three-string interaction vertex can reproduce some of the most important OPEs satisfied by the twist field.

  10. Metameric Modulation for Diffuse Visible Light Communications with Constant Ambient Lighting

    E-Print Network [OSTI]

    Little, Thomas

    untapped for wireless communications. Advancements in light emitting diode (LED) technology are making

  11. Light extraction analysis and enhancement in a quantum dot light emitting diode

    E-Print Network [OSTI]

    Wu, Shin-Tson

    Light extraction analysis and enhancement in a quantum dot light emitting diode Ruidong Zhu outcoupling and angular performance of quantum dot light emitting diode (QLED). To illustrate the design principles, we use a red QLED as an example and compare its performance with an organic light emitting diode

  12. Department of Mechanical Engineering Spring 2013 Lumax Lighting 2: LED Industrial High Bay Light Fixture

    E-Print Network [OSTI]

    Demirel, Melik C.

    PENNSTATE Department of Mechanical Engineering Spring 2013 Lumax Lighting 2: LED Industrial High Bay Light Fixture Overview The problem that our sponsor, Rich Taylor, presented to the team was to design a light fixture for an industrial setting using high power LED lights. The challenge

  13. Human lightness perception is guided by simple assumptions about reflectance and lighting

    E-Print Network [OSTI]

    Murray, Richard

    Human lightness perception is guided by simple assumptions about reflectance and lighting Richard F 0009, Toronto, Ontario, Canada, M3J 1P3 ABSTRACT Lightness constancy is the remarkable ability of human successful approaches to understanding lightness perception that have developed along independent paths

  14. LIGHTING RESEARCH PROGRAM Project 4.4 Portable Office Lighting Systems

    E-Print Network [OSTI]

    LIGHTING RESEARCH PROGRAM Project 4.4 Portable Office Lighting Systems FINAL REPORT Prepared For, Governor October 2005 CEC-500-2005-141-A13 #12;Portable Office Lighting Systems ­ Final Report Architectural Energy Corporation/CLTC PIER Lighting Research Program ii 500-01-041 CALIFORNIA ENERGY COMMISSION

  15. A Light Transport Framework for Lenslet Light Field Cameras Chia-Kai Liang

    E-Print Network [OSTI]

    California at San Diego, University of

    A Light Transport Framework for Lenslet Light Field Cameras Chia-Kai Liang Lytro Inc and Ravi Ramamoorthi University of California, San Diego Light field cameras capture full spatio-angular information of the light field, and enable many novel photographic and scientific applications. It is often stated

  16. Energy Efficiency Through Lighting Upgrades

    SciTech Connect (OSTI)

    Kara Berst; Maria Howeth

    2010-06-01T23:59:59.000Z

    Lighting upgrades including neon to LED, incandescent to CFL's and T-12 to T-8 and T-5's were completed through this grant. A total of 16 Chickasaw nation facilities decreased their carbon footprint because of these grant funds. Calculations used were based on comparing the energy usage from the previous year�¢����s average and the current energy usage. For facilities without a full year's set of energy bills, the month after installation was compared to the same month from the previous year. Overall, the effect the lighting change-outs had for the gaming centers and casinos far exceeded expectations. For the Madill Gaming Center; both an interior and exterior upgrade was performed which resulted in a 31% decrease in energy consumption. This same reduction was seen in every facility that participated in the grant. Just by simply changing out light bulbs to newer energy efficient equivalents, a decrease in energy usage can be achieved and this was validated by the return on investment seen at Chickasaw Nation facilities. Along with the technical project tasks were awareness sessions presented at Chickasaw Head Starts. The positive message of environmental stewardship was passed down to head start students and passed along to Chickasaw employees. Excitement was created in those that learned what they could do to help reduce their energy bills and many followed through and took the idea home. For a fairy low cost, the general public can also use this technique to lower their energy consumption both at home and at work. Although the idea behind the project was somewhat simple, true benefits have been gained through environmental awareness and reductions of energy costs.

  17. Simulation for Pre-Visualizing and Tuning Lighting Controller Behavior

    E-Print Network [OSTI]

    Radke, Rich

    daylighting and lighting control algorithms for a given space. Keywords: smart buildings, smart lighting, glazing, and shading devices have been decided. This prevents the early exploration of lighting

  18. DOE Solid-State Lighting Program Overview Brochure

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Lighting Program Shaping the Future of Solid-State Lighting Today, LED (light emitting diode) technologies illuminate grocery display cases, make parking garages and...

  19. Energy Department Announces Indoor Lighting Winners of Next Generation...

    Broader source: Energy.gov (indexed) [DOE]

    was launched in 2008 to promote excellence in the design of energy-efficient light-emitting diode (LED) commercial lighting fixtures or "luminaires." Solid-state lighting...

  20. Technology Development for Light Duty High Efficient Diesel Engines...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Light Duty High Efficient Diesel Engines Technology Development for Light Duty High Efficient Diesel Engines Improve the efficiency of diesel engines for light duty applications...

  1. How Do You Light Your Home Efficiently? | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    using task lighting, flipping the switch, and taking advantage of natural daylight can all help you save on your lighting costs. How do you light your home efficiently?...

  2. advanced blue light: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    of dental composites cured with blue light emitting diodes with either a light emitting diode (LED) based light curing unit (LCU) or a conventional halogen LCU do reserved....

  3. Bay Bridge Lights Presentation prepared by Zoon Engineering

    Energy Savers [EERE]

    2015 BAY BRIDGE LIGHTS Presentation prepared by Zoon Engineering Presentation Outline Lighting of the New East Span of the Bay Bridge Brief Over view Lighting Facts ...

  4. Product Quality Assurance for Off-Grid Lighting in Africa

    E-Print Network [OSTI]

    Mills, Evan; World Bank

    2008-01-01T23:59:59.000Z

    for Modern Lighting Product Quality Assurance for Off-GridLighting Africa Product Quality Assurance Workshop AirlieLighting Initiative Quality Certification Institute United

  5. Lighting Market Sourcebook for the U.S.

    E-Print Network [OSTI]

    Vorsatz, D.; Shown, L.; Koomey, J.; Moezzi, M.; Denver, A.; Atkinson, B.

    1997-01-01T23:59:59.000Z

    Potentials: Analysis of the Lighting Sector. Doctoral1996b. Residential Lighting: Use and Potential Savings.1993. Research for "The Lighting Pattern Book for Homes",

  6. Product Quality Assurance for Off-Grid Lighting in Africa

    E-Print Network [OSTI]

    Mills, Evan; World Bank

    2008-01-01T23:59:59.000Z

    Jeffrey Miller Pivotal Lighting Design 1601 Fifth Avenueaffordable, sustainable, lighting available to the millionsable to realize modern lighting options. R; Doluweera Peon,

  7. Effect of Research on Lighting for Modern Dance

    E-Print Network [OSTI]

    Grabowski, Andrew

    2013-01-01T23:59:59.000Z

    Print. Staines, Jackie. Lighting Techniques for Theatre In-Bibliography Graves, R. B. Lighting The Shakespearean Stage,Stanley. A Syllabus of Stage Lighting. New York: Drama Books

  8. The perception of shape, lighting, and material properties in images

    E-Print Network [OSTI]

    O'Shea, James Patrick

    2012-01-01T23:59:59.000Z

    the true lighting direction. . . . . . . . . . . . . . . .rep- resent different lighting tilts on the test object. Thedirection. We found the lighting used in the center image

  9. Stochastically Lighting Up Galaxies: Statistical Implications of Stellar Clustering

    E-Print Network [OSTI]

    da Silva, Robert Louis

    2014-01-01T23:59:59.000Z

    SANTA CRUZ STOCHASTICALLY LIGHTING UP GALAXIES: STATISTICAL2 SLUG - Stochastically Lighting Up Galaxies: Methods andx Abstract Stochastically Lighting Up Galaxies: Statistical

  10. EECBG Success Story: South Carolina Community Lights Up the Season...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    South Carolina Community Lights Up the Season with Energy-Efficient Holiday Lights EECBG Success Story: South Carolina Community Lights Up the Season with Energy-Efficient Holiday...

  11. Energy Savings Potential for Street Lighting in India

    E-Print Network [OSTI]

    Johnson, Alissa K.

    2014-01-01T23:59:59.000Z

    M. B. Kostic, “Light-emitting diodes in street and roadwayCompact fluorescent Light emitting diode High intensityCompact fluorescent Light emitting diode Mercury Vapor High

  12. Sandia Energy - Solid-State Lighting Technology: Current State...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Solid-State Lighting Technology: Current State of the Art and Grand Challenges Home Energy Research EFRCs Solid-State Lighting Science EFRC Overview Solid-State Lighting...

  13. Lighting and the Bottom Line

    E-Print Network [OSTI]

    Christensen, M.

    1981-01-01T23:59:59.000Z

    of replace~ent lamps, renlacement and clean ina labor, and electricity. These costs are a?nrOxiMately 5% for lamps, 10% for labor and ~5% for electricity. In a f'1.a.nufacturing plant the avera<1e apnroxi mate expenditure for laf'1ns ner employee per... year is $5.30. ~ith this infor~ation, kno''''in<1 the nu!'1ber of employees, the total annual operatin<1 cost of the li~hting system can be estimated. ~1any analvses of this type have shown that the cost of operating the lighting system is always...

  14. Slow light microfluidics: a proposal

    E-Print Network [OSTI]

    Sumetsky, M

    2014-01-01T23:59:59.000Z

    The resonant slow light structures created along a thin-walled optical capillary by nanoscale deformation of its surface can perform comprehensive simultaneous detection and manipulation of microfluidic components. This concept is illustrated with a model of a 0.5 millimeter long 5 nm high triangular bottle resonator created at a 50 micron radius silica capillary containing floating microparticles. The developed theory shows that the microparticle positions can be determined from the bottle resonator spectrum. In addition, the microparticles can be driven and simultaneously positioned at predetermined locations by the localized electromagnetic field created by the optimized superposition of eigenstates of this resonator, thus, exhibiting a multicomponent near field optical tweezers.

  15. Energy Conservation in Industrial Lighting

    E-Print Network [OSTI]

    Meharg, E.

    1979-01-01T23:59:59.000Z

    color of the fluorescent is a further advantage indoors. I INCAllDESCEiH 120000 3000 I 2500 ! L1FECOS LIFECOS;-$j 100000 2)00 250 W. _IIERCURY 80000 1500 50000 HPS 1000 f ! 40000 500 VARIOUS LIGHT SOURCES 20000 OUTDOOR LTG. - 10 t... MACHINE SHOP O~-=-=-----::-::------:::----,-,------=----------- o ro w ~~~ w ro ~ ~~ ill 120 ILLUMINATION LEVEL - FOOTCANDLES (MAINTAINED) HPS AT 30 FT. MTG. HT. PLUS INCAIWESCENT TASK LTG. ROOM: 230 X 45 FT. FIGURE 4 A similar illustration is given...

  16. Shedding Light on Nanocrystal Defects

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of ScienceandMesa del Sol HomeFacebookScholarship Fund scholarshipsShedding Light on Nanocrystal

  17. Lighting Basics | Department of Energy

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHigh SchoolIn12electron 9 5Let us countLighting Sign In About | Careers

  18. Light Duty Vehicle CNG Tanks

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the.pdfBreaking ofOil & Gas »ofMarketing | Department of EnergyLiekoviiLight Duty

  19. Morning Light | Open Energy Information

    Open Energy Info (EERE)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page onYou are now leaving Energy.gov You are now leaving Energy.gov You are beingZealand Jump to: navigation, searchOfRose BendMiasole IncMinutemanVistaZephyr) Jump to: navigation,WindLight

  20. Tips: Lighting | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the.pdfBreakingMayDepartmentTest for PumpingThe| Department ofAir DuctsTips: Lighting Tips:

  1. Shedding Light on Nanocrystal Defects

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What'sis Taking Over Our Instagram Secretary Moniz9 SeptemberSetting the StageCanon!Shedding Light on

  2. Shedding Light on Nanocrystal Defects

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What'sis Taking Over Our Instagram Secretary Moniz9 SeptemberSetting the StageCanon!Shedding Light

  3. Illuminating system and method for specialized and decorative lighting using liquid light guides

    DOE Patents [OSTI]

    Zorn, C.J.; Kross, B.J.; Majewski, S.; Wojcik, R.F.

    1998-08-25T23:59:59.000Z

    The present invention comprises an illumination system for specialized decorative lighting including a light source, a flexible plastic tube sheath for distributing the light to a remote location, a transparent liquid core filling the tube that has an index of refraction greater than that of the plastic tube and an arrangement where light coupled from the light source is caused to leak from the liquid light guide at desired locations for the purposes of specialized lighting, such as underwater illumination in swimming pools. 5 figs.

  4. Secretary Bodman Touts Importance of Cellulosic Ethanol at Georgia...

    Office of Environmental Management (EM)

    Touts Importance of Cellulosic Ethanol at Georgia Biorefinery Groundbreaking Secretary Bodman Touts Importance of Cellulosic Ethanol at Georgia Biorefinery Groundbreaking October...

  5. Secretary Chu to Discuss Importance of Electric Grid Modernization...

    Energy Savers [EERE]

    Discuss Importance of Electric Grid Modernization to U.S. Competitiveness at Gridwise Global Forum Secretary Chu to Discuss Importance of Electric Grid Modernization to U.S....

  6. US Crude Oil Production Surpasses Net Imports | Department of...

    Office of Environmental Management (EM)

    US Crude Oil Production Surpasses Net Imports US Crude Oil Production Surpasses Net Imports Source: Energy Information Administration Short Term Energy Outlook. Chart by Daniel...

  7. Energy Secretary Bodman in Turkey to Highlight Importance of...

    Office of Environmental Management (EM)

    in Turkey to Highlight Importance of Expanding Oil and Gas Supply and Infrastructure Energy Secretary Bodman in Turkey to Highlight Importance of Expanding Oil and Gas Supply and...

  8. DOE Researchers Achieve Important Genetic Breakthroughs to Help...

    Office of Environmental Management (EM)

    Researchers Achieve Important Genetic Breakthroughs to Help Develop Cheaper Biofuels DOE Researchers Achieve Important Genetic Breakthroughs to Help Develop Cheaper Biofuels...

  9. Forest Carbon - Sustaining an Important Climate Service: Roles...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Forest Carbon - Sustaining an Important Climate Service: Roles of Biomass Use and Markets Forest Carbon - Sustaining an Important Climate Service: Roles of Biomass Use and Markets...

  10. Handling Strategies for Import Containers at Marine Terminals

    E-Print Network [OSTI]

    De Castilho, Bernardo; Daganzo, Carlos F.

    1993-01-01T23:59:59.000Z

    Containers at Marine Terminals Bemardo De Castilho Carlos F.Import Containers at Marine Terminals Bernardo De CastilhoFOR IMPORT AT MARINE TERMINALS CONTAINERS BERNARDO DE

  11. Rule Proposed to Prohibit Importation of Products that Fail to...

    Energy Savers [EERE]

    Rule Proposed to Prohibit Importation of Products that Fail to Comply with DOE Energy Conservation Standards Rule Proposed to Prohibit Importation of Products that Fail to Comply...

  12. Development of a Web-based Emissions Reduction Calculator for Street Light and Traffic Light Retrofits

    E-Print Network [OSTI]

    Liu, Z.; Gilman, D.; Haberl, J. S.; Culp, C.

    2005-01-01T23:59:59.000Z

    , street lights and traffic lights represent one of the largest categories of electricity used by a city. By retrofitting the street lights with energy efficient lamps such as high pressure sodium and metal halide and traffic lights with light-emitting... diode (LED) traffic signals, a city 1 In the 2003 and 2005 Texas State legislative sessions, the emissions reductions legislation in Senate Bill 5 was modified by House bill 3235, and House bill 1365...

  13. Light-Emitting Diodes in the Solid-State Lighting Systems

    E-Print Network [OSTI]

    Sparavigna, Amelia Carolina

    2014-01-01T23:59:59.000Z

    Red and green light-emitting diodes (LEDs) had been produced for several decades before blue emitting diodes, suitable for lighting applications, were widely available. Today, we have the possibility of combining the three fundamental colours to have a bright white light. And therefore, a new form of lighting, the solid-state lighting, has now become a reality. Here we discuss LEDs and some of their applications in displays and lamps.

  14. Controls for Solid-State Lighting

    SciTech Connect (OSTI)

    Rubinstein, Francis

    2007-06-22T23:59:59.000Z

    This study predicts new hybrid lighting applications for LEDs. In hybrid lighting, LEDs provide a low-energy 'standby' light level while another, more powerful, efficient light source provides light for occupied periods. Lighting controls will allow the two light sources to work together through an appropriate control strategy, typically motion-sensing. There are no technical barriers preventing the use of low through high CRI LEDs for standby lighting in many interior and exterior applications today. The total luminous efficacy of LED systems could be raised by increasing the electrical efficiency of LED drivers to the maximum practically achievable level (94%). This would increase system luminous efficacy by 20-25%. The expected market volumes for many types of LEDs should justify the evolution of new LED drivers that use highly efficient ICs and reduce parts count by means of ASICs. Reducing their electronics parts count by offloading discrete components onto integrated circuits (IC) will allow manufacturers to reduce the cost of LED driver electronics. LED luminaire manufacturers will increasingly integrate the LED driver and thermal management directly in the LED fixture. LED luminaires of the future will likely have no need for separable lamp and ballast because the equipment life of all the LED luminaire components will all be about the same (50,000 hours). The controls and communications techniques used for communicating with conventional light sources, such as dimmable fluorescent lighting, are appropriate for LED illumination for energy management purposes. DALI has been used to control LED systems in new applications and the emerging ZigBee protocol could be used for LEDs as well. Major lighting companies are already moving in this direction. The most significant finding is that there is a significant opportunity to use LEDs today for standby lighting purposes. Conventional lighting systems can be made more efficient still by using LEDs to provide a low-energy standby state when lower light levels are acceptable.

  15. Demand Responsive Lighting: A Scoping Study

    SciTech Connect (OSTI)

    Rubinstein, Francis; Kiliccote, Sila

    2007-01-03T23:59:59.000Z

    The objective of this scoping study is: (1) to identify current market drivers and technology trends that can improve the demand responsiveness of commercial building lighting systems and (2) to quantify the energy, demand and environmental benefits of implementing lighting demand response and energy-saving controls strategies Statewide. Lighting systems in California commercial buildings consume 30 GWh. Lighting systems in commercial buildings often waste energy and unnecessarily stress the electrical grid because lighting controls, especially dimming, are not widely used. But dimmable lighting equipment, especially the dimming ballast, costs more than non-dimming lighting and is expensive to retrofit into existing buildings because of the cost of adding control wiring. Advances in lighting industry capabilities coupled with the pervasiveness of the Internet and wireless technologies have led to new opportunities to realize significant energy saving and reliable demand reduction using intelligent lighting controls. Manufacturers are starting to produce electronic equipment--lighting-application specific controllers (LAS controllers)--that are wirelessly accessible and can control dimmable or multilevel lighting systems obeying different industry-accepted protocols. Some companies make controllers that are inexpensive to install in existing buildings and allow the power consumed by bi-level lighting circuits to be selectively reduced during demand response curtailments. By intelligently limiting the demand from bi-level lighting in California commercial buildings, the utilities would now have an enormous 1 GW demand shed capability at hand. By adding occupancy and light sensors to the remotely controllable lighting circuits, automatic controls could harvest an additional 1 BkWh/yr savings above and beyond the savings that have already been achieved. The lighting industry's adoption of DALI as the principal wired digital control protocol for dimming ballasts and increased awareness of the need to standardize on emerging wireless technologies are evidence of this transformation. In addition to increased standardization of digital control protocols controller capabilities, the lighting industry has improved the performance of dimming lighting systems over the last two years. The system efficacy of today's current dimming ballasts is approaching that of non-dimming program start ballasts. The study finds that the benefits of applying digital controls technologies to California's unique commercial buildings market are enormous. If California were to embark on an concerted 20 year program to improve the demand responsiveness and energy efficiency of commercial building lighting systems, the State could avoid adding generation capacity, improve the elasticity of the grid, save Californians billion of dollars in avoided energy charges and significantly reduce greenhouse gas emissions.

  16. Full phosphorescent white-light organic light-emitting diodes with improved color stability and efficiency by fine tuning primary emission contributions

    SciTech Connect (OSTI)

    Hua, Wang, E-mail: wmsu2008@sinano.ac.cn, E-mail: wanghua001@tyut.edu.cn; Du, Xiaogang [Key Laboratory of Interface Science and Engineering in Advanced Materials, Taiyuan University of Technology, Ministry of Education, Taiyuan 030024 (China) [Key Laboratory of Interface Science and Engineering in Advanced Materials, Taiyuan University of Technology, Ministry of Education, Taiyuan 030024 (China); Research Center of Advanced Materials Science and Technology, Taiyuan University of Technology, Taiyuan 030024 (China); Su, Wenming, E-mail: wmsu2008@sinano.ac.cn, E-mail: wanghua001@tyut.edu.cn; Zhang, Dongyu [Printable Electronics Research Centre, Suzhou Institute of Nano-Tech and Nano-Bionics, CAS, suzhou 215123 (China)] [Printable Electronics Research Centre, Suzhou Institute of Nano-Tech and Nano-Bionics, CAS, suzhou 215123 (China); Lin, Wenjing [Key Laboratory of Interface Science and Engineering in Advanced Materials, Taiyuan University of Technology, Ministry of Education, Taiyuan 030024 (China) [Key Laboratory of Interface Science and Engineering in Advanced Materials, Taiyuan University of Technology, Ministry of Education, Taiyuan 030024 (China); Research Center of Advanced Materials Science and Technology, Taiyuan University of Technology, Taiyuan 030024 (China); Printable Electronics Research Centre, Suzhou Institute of Nano-Tech and Nano-Bionics, CAS, suzhou 215123 (China)

    2014-02-15T23:59:59.000Z

    In this paper, a novel type of white-light organic light emitting diode (OLED) with high color stability was reported, in which the yellow-light emission layer of (4,4{sup ?}-N,N{sup ?}-dicarbazole)biphenyl (CBP) : tris(2-phenylquinoline-C2,N{sup ?})iridium(III) (Ir(2-phq){sub 3}) was sandwiched by double blue-light emission layers of 1,1-bis-[(di-4-tolylamino)pheny1]cyclohexane (TAPC) : bis[4,6-(di-fluorophenyl)-pyridinato-N,C2{sup ?}]picolinate (FIrpic) and tris[3-(3-pyridyl)mesityl]borane (3TPYMB):FIrpic. And, it exhibited the maximum current efficiency of 33.1 cd/A, the turn-on voltage at about 3 V and the maximum luminance in excess of 20000 cd/m{sup 2}. More important, it realized very stable white-light emission, and its CIE(x, y) coordinates only shift from (0.34, 0.37) to (0.33, 0.37) as applied voltage increased from 5 V to 12 V. It is believed that the new scheme in emission layer of white-light OLED can fine tune the contribution of primary emission with applied voltage changed, resulting in high quality white-light OLED.

  17. Green Light-Emitting Diode Makes Highly Efficient White Light; The Spectrum of Clean Energy Innovation (Fact Sheet)

    SciTech Connect (OSTI)

    Not Available

    2010-06-01T23:59:59.000Z

    Fact sheet describing NREL's green light emitting diode that can lead to higher efficiency white light used in indoor lighting applications.

  18. Appliances, Lighting, Electronics, and Miscellaneous Equipment Electricity Use in New Homes

    E-Print Network [OSTI]

    Brown, Richard E.; Rittelman, William; Parker, Danny; Homan, Gregory

    2007-01-01T23:59:59.000Z

    62440 Appliances, Lighting, Electronics, and Miscellaneousof California. Appliances, Lighting, Electronics, anduses (appliances, lighting, electronics, and miscellaneous

  19. The Dark Penguin Shines Light at Colliders

    E-Print Network [OSTI]

    Primulando, Reinard; Tsai, Yuhsin

    2015-01-01T23:59:59.000Z

    Collider experiments are one of the most promising ways to constrain Dark Matter (DM) interactions. For several types of DM-Standard Model couplings, a meaningful interpretation of the results requires to go beyond effective field theory, considering simplified models with light mediators. This is especially important in the case of loop-mediated interactions. In this paper we perform the first simplified model study of the magnetic dipole interacting DM, by including the one-loop momentum-dependent form factors that mediate the coupling -- given by the Dark Penguin -- in collider processes. We compute bounds from the monojet, monophoton, and diphoton searches at the $8$ and $14$ TeV LHC, and compare the results to those of direct and indirect detection experiments. Future searches at the $100$ TeV hadron collider and at the ILC are also addressed. We find that the optimal search strategy requires loose cuts on the missing transverse energy, to capture the enhancement of the form factors near the threshold fo...

  20. Evaluation of Covariances for Actinides and Light Elements at LANL

    SciTech Connect (OSTI)

    Kawano, T. [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States)], E-mail: kawano@lanl.gov; Talou, P.; Young, P.G.; Hale, G.; Chadwick, M.B.; Little, R.C. [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States)

    2008-12-15T23:59:59.000Z

    Los Alamos evaluates covariances for the evaluated nuclear data library (ENDF), mainly for actinides above the resonance region and for light elements in the entire energy range. We also develop techniques to evaluate the covariance data, like Bayesian and least-squares fitting methods, which are important to explore the uncertainty information on different types of physical quantities such as elastic scattering angular distribution, or prompt neutron fission spectra. This paper summarizes our current activities of the covariance evaluation work at LANL, including the actinide and light element data mainly for criticality safety studies and transmutation technology. The Bayesian method based on the Kalman filter technique, which combines uncertainties in the theoretical model and experimental data, is discussed.