Powered by Deep Web Technologies
Note: This page contains sample records for the topic "imaging multispectral thermal" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Multispectral thermal imaging  

SciTech Connect

Many remote sensing applications rely on imaging spectrometry. Here the authors use imaging spectrometry for thermal and multispectral signatures measured from a satellite platform enhanced with a combination of accurate calibrations and on-board data for correcting atmospheric distortions. The approach is supported by physics-based end-to-end modeling and analysis, which permits a cost-effective balance between various hardware and software aspects. The goal is to develop and demonstrate advanced technologies and analysis tools toward meeting the needs of the customer; at the same time, the attributes of this system can address other applications in such areas as environmental change, agriculture, and volcanology.

Weber, P.G.; Bender, S.C.; Borel, C.C.; Clodius, W.B.; Smith, B.W. [Los Alamos National Lab., NM (United States). Space and Remote Sensing Sciences Group; Garrett, A.; Pendergast, M.M. [Westinghouse Savannah River Corp., Aiken, SC (United States). Savannah River Technology Center; Kay, R.R. [Sandia National Lab., Albuquerque, NM (United States). Monitoring Systems and Technology Center

1998-12-01T23:59:59.000Z

2

ARM - Evaluation Product - Multispectral Thermal Imager (MTI)  

NLE Websites -- All DOE Office Websites (Extended Search)

ProductsMultispectral Thermal Imager (MTI) ProductsMultispectral Thermal Imager (MTI) Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Evaluation Product : Multispectral Thermal Imager (MTI) 2000.10.01 - 2003.05.02 Site(s) NSA SGP General Description The Multispectral Thermal Imager is a space-based research and development project sponsored by the U.S. Department of Energy (DOE), Office of Nonproliferation and National Security. MTI's primary objective is to demonstrate advanced multispectral and thermal imaging, image processing, and associated technologies that could be used in future systems for detecting and characterizing facilities producing weapons of mass destruction. However, ARM and the MTI have an arrangement that allows ARM to receive MTI images.

3

Design Considerations, Modeling and Analysis for the Multispectral Thermal Imager  

SciTech Connect

The design of remote sensing systems is driven by the need to provide cost-effective, substantive answers to questions posed by our customers. This is especially important for space-based systems, which tend to be expensive, and which generally cannot be changed after they are launched. We report here on the approach we employed in developing the desired attributes of a satellite mission, namely the Multispectral Thermal Imager. After an initial scoping study, we applied a procedure which we call: "End-to-end modeling and analysis (EEM)." We began with target attributes, translated to observable signatures and then propagated the signatures through the atmosphere to the sensor location. We modeled the sensor attributes to yield a simulated data stream, which was then analyzed to retrieve information about the original target. The retrieved signature was then compared to the original to obtain a figure of merit: hence the term "end-to-end modeling and analysis." We base the EEM in physics to ensure high fidelity and to permit scaling. As the actual design of the payload evolves, and as real hardware is tested, we can update the EEM to facilitate trade studies, and to judge, for example, whether components that deviate from specifications are acceptable.

Borel, C.C.; Clodius, W.B.; Cooke, B.J.; Smith, B.W.; Weber, P.G.

1999-02-01T23:59:59.000Z

4

Definition: Multispectral Imaging | Open Energy Information  

Open Energy Info (EERE)

Imaging Imaging Jump to: navigation, search Dictionary.png Multispectral Imaging Multispectral surveys image the earth in an average of ten wide bands over a wide spectral range. Multispectral sensors measure the electromagnetic spectrum in discrete, discontinuous bands (unlike the continuous hyperspectral image). Multispectral sensors are capable of relative material delineation. The thermal wavelength range of the multispectral survey senses heat energy from the Earth's surface. It can be used to sense surface temperature, including anomalies associated with active geothermal or volcanic systems. Both multispectral and hyperspectral remote sensing observations are available. This range can also be used to map mineralogy associate with common rock-forming silicates.[1]

5

Multispectral Imaging | Open Energy Information  

Open Energy Info (EERE)

Multispectral Imaging Multispectral Imaging Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Technique: Multispectral Imaging Details Activities (35) Areas (22) Regions (1) NEPA(0) Exploration Technique Information Exploration Group: Remote Sensing Techniques Exploration Sub Group: Passive Sensors Parent Exploration Technique: Passive Sensors Information Provided by Technique Lithology: relative mineral maps Stratigraphic/Structural: aerial photographs can show structures Hydrological: delineate locations of surface water features Thermal: vegetation maps can show plants stressed due to nearby thermal activity Cost Information Low-End Estimate (USD): 10.001,000 centUSD 0.01 kUSD 1.0e-5 MUSD 1.0e-8 TUSD / sq. mile Median Estimate (USD): 370.2337,023 centUSD

6

Ground truth measurements plan for the Multispectral Thermal Imager (MTI) satellite  

SciTech Connect

Sandia National Laboratories (SNL), Los Alamos National Laboratory (LANL), and the Savannah River Technology Center (SRTC) have developed a diverse group of algorithms for processing and analyzing the data that will be collected by the Multispectral Thermal Imager (MTI) after launch late in 1999. Each of these algorithms must be verified by comparison to independent surface and atmospheric measurements. SRTC has selected 13 sites in the continental U.S. for ground truth data collections. These sites include a high altitude cold water target (Crater Lake), cooling lakes and towers in the warm, humid southeastern US, Department of Energy (DOE) climate research sites, the NASA Stennis satellite Validation and Verification (V and V) target array, waste sites at the Savannah River Site, mining sites in the Four Corners area and dry lake beds in the southwestern US. SRTC has established mutually beneficial relationships with the organizations that manage these sites to make use of their operating and research data and to install additional instrumentation needed for MTI algorithm V and V.

Garrett, A.J.

2000-01-03T23:59:59.000Z

7

Multispectral imaging method and apparatus  

DOE Patents (OSTI)

A multispectral imaging method and apparatus are described which are adapted for use in determining material properties, especially properties characteristic of abnormal non-dermal cells. A target is illuminated with a narrow band light beam. The target expresses light in response to the excitation. The expressed light is collected and the target's response at specific response wavelengths to specific excitation wavelengths is measured. From the measured multispectral response the target's properties can be determined. A sealed, remote probe and robust components can be used for cervical imaging. 5 figs.

Sandison, D.R.; Platzbecker, M.R.; Vargo, T.D.; Lockhart, R.R.; Descour, M.R.; Richards-Kortum, R.

1999-07-06T23:59:59.000Z

8

Multispectral Imaging At Dixie Meadows Area (Martin, Et Al.,...  

Open Energy Info (EERE)

Multispectral Imaging At Dixie Meadows Area (Martin, Et Al., 2004) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Multispectral Imaging At Dixie...

9

Multispectral Imaging At Maui Area (DOE GTP) | Open Energy Information  

Open Energy Info (EERE)

Multispectral Imaging At Maui Area (DOE GTP) Exploration Activity Details Location Maui Area Exploration Technique Multispectral Imaging Activity Date Usefulness not indicated...

10

Multispectral Imaging At Alum Area (DOE GTP) | Open Energy Information  

Open Energy Info (EERE)

Multispectral Imaging At Alum Geothermal Area (DOE GTP) Exploration Activity Details Location Alum Geothermal Area Exploration Technique Multispectral Imaging Activity Date...

11

Definition: Multispectral Thermal Infrared | Open Energy Information  

Open Energy Info (EERE)

Infrared Infrared Jump to: navigation, search Dictionary.png Multispectral Thermal Infrared This wavelength range senses heat energy from the Earth's surface. It can be used to sense surface temperature, including anomalies associated with active geothermal or volcanic systems. Both multispectral and hyperspectral remote sensing observations are available. This range can also be used to map mineralogy associate with common rock-forming silicates.[1][2] View on Wikipedia Wikipedia Definition References ↑ http://en.wikipedia.org/wiki/Thermal_infrared_spectroscopy ↑ http://asterweb.jpl.nasa.gov/ Ret LikeLike UnlikeLike You like this.Sign Up to see what your friends like. rieved from "http://en.openei.org/w/index.php?title=Definition:Multispectral_Thermal_Infrared&oldid=601561

12

Multispectral Imaging (Laney, 2005) | Open Energy Information  

Open Energy Info (EERE)

Page Page Edit History Facebook icon Twitter icon » Multispectral Imaging (Laney, 2005) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Multispectral Imaging (Laney, 2005) Exploration Activity Details Location Unspecified Exploration Technique Multispectral Imaging Activity Date Usefulness not indicated DOE-funding Unknown Notes Design of Sampling Strategies to Detect CO2 Emissions From Hidden Geothermal Systems, Lewicki, Oldenburg and Kennedy. The objective of this project is to investigate geothermal CO2 monitoring in the near surface as a tool to discover hidden geothermal reservoirs. A primary goal of this project is to develop an approach that places emphasis on cost and time-efficient near-surface exploration methods and yields results to guide

13

Multispectral Imaging (Monaster And Coolbaugh, 2007) | Open Energy  

Open Energy Info (EERE)

Multispectral Imaging (Monaster And Coolbaugh, 2007) Multispectral Imaging (Monaster And Coolbaugh, 2007) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Multispectral Imaging (Monaster And Coolbaugh, 2007) Exploration Activity Details Location Unspecified Exploration Technique Multispectral Imaging Activity Date Usefulness useful DOE-funding Unknown References Francis C. Monastero, Mark F. Coolbaugh (2007) Advances In Geothermal Resource Exploration Circa 2007 Retrieved from "http://en.openei.org/w/index.php?title=Multispectral_Imaging_(Monaster_And_Coolbaugh,_2007)&oldid=510998" Category: Exploration Activities What links here Related changes Special pages Printable version Permanent link Browse properties 429 Throttled (bot load) Error 429 Throttled (bot load) Throttled (bot load)

14

Multispectral Imaging At Cove Fort Area (Laney, 2005) | Open Energy  

Open Energy Info (EERE)

Cove Fort Area (Laney, 2005) Cove Fort Area (Laney, 2005) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Multispectral Imaging At Cove Fort Area (Laney, 2005) Exploration Activity Details Location Cove Fort Geothermal Area Exploration Technique Multispectral Imaging Activity Date Usefulness useful DOE-funding Unknown Notes Geology and Geophysics of Geothermal Systems, Gregory Nash, 2005. Vegetalspectral analysis at Cove Fort-Sulphurdale, Utah was tested as a method of detecting hidden faults in exploration efforts. This effort proved to be successful and resulted in the Following published paper: Nash, G. D., J. N. Moore, and T. Sperry, 2003. "Vegetal-spectral anomaly detection at the Cove Fort-Sulphurdale thermal anomaly, Utah, USA: implications for use in geothermal exploration." Geothermics, v. 32, p.

15

Multispectral Imaging At Pilgrim Hot Springs Area (Prakash, Et...  

Open Energy Info (EERE)

Up Search Page Edit History Facebook icon Twitter icon Multispectral Imaging At Pilgrim Hot Springs Area (Prakash, Et Al., 2010) Jump to: navigation, search GEOTHERMAL...

16

Multispectral Imaging At Silver Peak Area (DOE GTP) | Open Energy...  

Open Energy Info (EERE)

Silver Peak Area (DOE GTP) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Multispectral Imaging At Silver Peak Area (DOE GTP) Exploration...

17

Multispectral Imaging At Glass Buttes Area (DOE GTP) | Open Energy...  

Open Energy Info (EERE)

Glass Buttes Area (DOE GTP) Exploration Activity Details Location Glass Buttes Area Exploration Technique Multispectral Imaging Activity Date Usefulness not indicated DOE-funding...

18

Multispectral Imaging At Fish Lake Valley Area (Deymonaz, Et Al., 2008) |  

Open Energy Info (EERE)

Multispectral Imaging At Fish Lake Valley Area (Deymonaz, Et Al., 2008) Multispectral Imaging At Fish Lake Valley Area (Deymonaz, Et Al., 2008) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Multispectral Imaging At Fish Lake Valley Area (Deymonaz, Et Al., 2008) Exploration Activity Details Location Fish Lake Valley Area Exploration Technique Multispectral Imaging Activity Date Spectral Imaging Sensor ASTER Usefulness useful DOE-funding Unknown Notes For this project, fused imagery was created using ASTER data and USGS Digital Orthophoto Quandrangles (DOQs). The ASTER data have a spatial resolution of 15 m for the visible to infrared and near_infrared bands, and 30 m for shortwave_infrared bands; with a cost of $85.00 per 60 x 60 km image. Thermal anomalies were mapped using ASTER kinetic temperature data

19

Multispectral Imaging At Rangely Oilfield Area (Pickles & Cover, 2004) |  

Open Energy Info (EERE)

Multispectral Imaging At Rangely Oilfield Area (Pickles & Cover, 2004) Multispectral Imaging At Rangely Oilfield Area (Pickles & Cover, 2004) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Multispectral Imaging At Rangely Oilfield Area (Pickles & Cover, 2004) Exploration Activity Details Location Rangely Oilfield Area Exploration Technique Multispectral Imaging Activity Date Usefulness useful DOE-funding Unknown Notes Airborne hyperspectral imaging applied to determine vegetation and CO2 leakage in the Rangely oilfield of northwest Colorado - results may be useful for geothermal exploration. References W. Pickles, W. Cover (2004) Hyperspectral Geobotanical Remote Sensing For Co2 Storage Monitoring Retrieved from "http://en.openei.org/w/index.php?title=Multispectral_Imaging_At_Rangely_Oilfield_Area_(Pickles_%26_Cover,_2004)&oldid=511013"

20

Multispectral Imaging At Yellowstone Region (Hellman & Ramsey...  

Open Energy Info (EERE)

Hot Springs And Associated Deposits In Yellowstone National Park Using Aster And Aviris Remote Sensing Retrieved from "http:en.openei.orgwindex.php?titleMultispectralImagin...

Note: This page contains sample records for the topic "imaging multispectral thermal" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Multispectral and panchromatic images fusion by adaptive PCNN  

Science Conference Proceedings (OSTI)

As for low resolution of remote sensing images, a novel image fusion algorithm by adaptive PCNN was proposed. The multi-spectral image is firstly converted from RGB to l?? color space. Then, the input images are adaptively decomposed ... Keywords: adaptive parameter setting, color space conversation, image fusion, pulse-coupled neural network (PCNN)

Yong Li; Ke Wang; Da-ke Chen

2010-01-01T23:59:59.000Z

22

Multispectral Imaging At Silver Peak Area (Laney, 2005) | Open Energy  

Open Energy Info (EERE)

Laney, 2005) Laney, 2005) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Multispectral Imaging At Silver Peak Area (Laney, 2005) Exploration Activity Details Location Silver Peak Area Exploration Technique Multispectral Imaging Activity Date Usefulness not indicated DOE-funding Unknown Notes Geology and Geophysics of Geothermal Systems, Gregory Nash, 2005. A third objective was testing ASTER multispectral data for small-scale mapping of the geology of the northern Silver Peak Range, Nevada near the Fish Lake Valley geothermal field. References Patrick Laney (2005) Federal Geothermal Research Program Update - Fiscal Year 2004 Retrieved from "http://en.openei.org/w/index.php?title=Multispectral_Imaging_At_Silver_Peak_Area_(Laney,_2005)&oldid=511017"

23

Multispectral imaging of the ocular fundus using light emitting diode illumination  

E-Print Network (OSTI)

Multispectral imaging of the ocular fundus using light emitting diode illumination N. L. Everdell,1 on light emitting diode LED illumination that produces multispectral optical images of the human ocular

Claridge, Ela

24

Multispectral Imaging At Buffalo Valley Hot Springs Area (Laney, 2005) |  

Open Energy Info (EERE)

Multispectral Imaging At Buffalo Valley Hot Springs Multispectral Imaging At Buffalo Valley Hot Springs Area (Laney, 2005) Exploration Activity Details Location Buffalo Valley Hot Springs Area Exploration Technique Multispectral Imaging Activity Date Usefulness useful DOE-funding Unknown Notes Remote Sensing for Exploration and Mapping of Geothermal Resources, Wendy Calvin, 2005. Task 1: Detailed analysis of hyperspectral imagery obtained in summer of 2003 over Brady's Hot Springs region was completed and validated (Figure 1). This analysis provided a local map of both sinter and tufa deposits surrounding the Ormat plant, identified fault extensions not previously recognized from field mapping and has helped constrain where to put additional wells that were drilled at the site. Task 2: Initial analysis of Landsat and ASTER data for Buffalo Valley and Pyramid Lake was

25

Multispectral Imaging At The Needles Area (Laney, 2005) | Open Energy  

Open Energy Info (EERE)

Needles Area (Laney, 2005) Needles Area (Laney, 2005) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Multispectral Imaging At The Needles Area (Laney, 2005) Exploration Activity Details Location The Needles Area Exploration Technique Multispectral Imaging Activity Date Usefulness useful DOE-funding Unknown Notes Remote Sensing for Exploration and Mapping of Geothermal Resources, Wendy Calvin, 2005. Task 1: Detailed analysis of hyperspectral imagery obtained in summer of 2003 over Brady's Hot Springs region was completed and validated (Figure 1). This analysis provided a local map of both sinter and tufa deposits surrounding the Ormat plant, identified fault extensions not previously recognized from field mapping and has helped constrain where to

26

OIL SPILL SENSOR USING MULTISPECTRAL INFRARED IMAGING VIA 1 MINIMIZATION  

E-Print Network (OSTI)

OIL SPILL SENSOR USING MULTISPECTRAL INFRARED IMAGING VIA 1 MINIMIZATION Yingying Li , Wei Computational and Applied Mathematics, Rice University ABSTRACT Early detection of oil spill events is the key in detecting the early onset of a small-scale oil spill event. Based on an infrared oil-water contrast model

Yin, Wotao

27

Spectral change directions of multispectral subpixels in image fusion  

Science Conference Proceedings (OSTI)

In an image fusion process, the spatial detail in a panchromatic pixel is injected into the corresponding n-band multispectral (MS) subpixel to yield a synthetic pixel. The synthetic pixel can be regarded as the sum of three terms: the MS subpixel, a ...

Linhai Jing; Qiuming Cheng

2011-03-01T23:59:59.000Z

28

Multispectral Imaging At Coso Geothermal Area (1990) | Open Energy  

Open Energy Info (EERE)

) ) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Multispectral Imaging At Coso Geothermal Area (1990) Exploration Activity Details Location Coso Geothermal Area Exploration Technique Multispectral Imaging Activity Date 1990 Usefulness not indicated DOE-funding Unknown Exploration Basis To understand the complex geology seen on the surface and to try to improve the method of locating geothermal wells. Notes Remote sensing studies have been made in and adjacent to the Coso geothermal field using TM FCC satellite imagery, 1:100,000 scale, US Geological Survey orthophotos, 1:24,000 scale, and proprietary black-and-white photography by California Energy Company, Inc., at various scales including black-and-white positive film transparencies at a scale of

29

Multispectral Imaging At Rhodes Marsh Area (Shevenell, Et Al., 2008) | Open  

Open Energy Info (EERE)

Rhodes Marsh Area (Shevenell, Et Al., 2008) Rhodes Marsh Area (Shevenell, Et Al., 2008) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Multispectral Imaging At Rhodes Marsh Area (Shevenell, Et Al., 2008) Exploration Activity Details Location Rhodes Marsh Area Exploration Technique Multispectral Imaging Activity Date Usefulness useful DOE-funding Unknown Notes Kratt et al. (2006) demonstrate the effectiveness of using a field-portable ASD Fieldspec spectroradiometer and satellite-based Advanced Spaceborne Thermal and emitted Reflectance Radiometer (ASTER) imagery for mapping borate minerals in the field. Borate crusts that were partially mined during the 1800s were identified and mapped at Rhodes, Teels, and Columbus Marshes (playas), all in western Nevada (Figure 1).

30

Multispectral Imaging At Teels Marsh Area (Shevenell, Et Al., 2008) | Open  

Open Energy Info (EERE)

Teels Marsh Area (Shevenell, Et Al., 2008) Teels Marsh Area (Shevenell, Et Al., 2008) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Multispectral Imaging At Teels Marsh Area (Shevenell, Et Al., 2008) Exploration Activity Details Location Teels Marsh Area Exploration Technique Multispectral Imaging Activity Date Usefulness useful DOE-funding Unknown Notes Kratt et al. (2006) demonstrate the effectiveness of using a field-portable ASD Fieldspec spectroradiometer and satellite-based Advanced Spaceborne Thermal and emitted Reflectance Radiometer (ASTER) imagery for mapping borate minerals in the field. Borate crusts that were partially mined during the 1800s were identified and mapped at Rhodes, Teels, and Columbus Marshes (playas), all in western Nevada (Figure 1).

31

Multispectral Imaging At Columbus Salt Marsh Area (Shevenell, Et Al., 2008)  

Open Energy Info (EERE)

Marsh Area (Shevenell, Et Al., 2008) Marsh Area (Shevenell, Et Al., 2008) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Multispectral Imaging At Columbus Salt Marsh Area (Shevenell, Et Al., 2008) Exploration Activity Details Location Columbus Salt Marsh Area Exploration Technique Multispectral Imaging Activity Date Usefulness useful DOE-funding Unknown Notes Kratt et al. (2006) demonstrate the effectiveness of using a field-portable ASD Fieldspec spectroradiometer and satellite-based Advanced Spaceborne Thermal and emitted Reflectance Radiometer (ASTER) imagery for mapping borate minerals in the field. Borate crusts that were partially mined during the 1800s were identified and mapped at Rhodes, Teels, and Columbus Marshes (playas), all in western Nevada (Figure 1).

32

Multispectral Imaging At Rhodes Marsh Area (Kratt, Et Al., 2006) | Open  

Open Energy Info (EERE)

Multispectral Imaging At Rhodes Marsh Area (Kratt, Et Al., 2006) Multispectral Imaging At Rhodes Marsh Area (Kratt, Et Al., 2006) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Multispectral Imaging At Rhodes Marsh Area (Kratt, Et Al., 2006) Exploration Activity Details Location Rhodes Marsh Area Exploration Technique Multispectral Imaging Activity Date Usefulness useful regional reconnaissance DOE-funding Unknown Notes Mapped present-day borate evaporites in Teels and Rhodes Marsh with ASTER satellite imagery References C. Kratt, M. Coolbaugh, Wendy Calvin (2006) Remote Detection Of Quaternary Borate Deposits With Aster Satellite Imagery As A Geothermal Exploration Tool Retrieved from "http://en.openei.org/w/index.php?title=Multispectral_Imaging_At_Rhodes_Marsh_Area_(Kratt,_Et_Al.,_2006)&oldid=511014"

33

Multispectral Imaging At Teels Marsh Area (Kratt, Et Al., 2006) | Open  

Open Energy Info (EERE)

Multispectral Imaging At Teels Marsh Area (Kratt, Et Al., 2006) Multispectral Imaging At Teels Marsh Area (Kratt, Et Al., 2006) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Multispectral Imaging At Teels Marsh Area (Kratt, Et Al., 2006) Exploration Activity Details Location Teels Marsh Area Exploration Technique Multispectral Imaging Activity Date Usefulness useful regional reconnaissance DOE-funding Unknown Notes Mapped present-day borate evaporites in Teels and Rhodes Marsh with ASTER satellite imagery References C. Kratt, M. Coolbaugh, Wendy Calvin (2006) Remote Detection Of Quaternary Borate Deposits With Aster Satellite Imagery As A Geothermal Exploration Tool Retrieved from "http://en.openei.org/w/index.php?title=Multispectral_Imaging_At_Teels_Marsh_Area_(Kratt,_Et_Al.,_2006)&oldid=511018"

34

Resampling approach for anomaly detection in multispectral images  

Science Conference Proceedings (OSTI)

We propose a novel approach for identifying the 'most unusual' samples in a data set, based on a resampling of data attributes. The resampling produces a 'background class' and then binary classification is used to distinguish the original training set from the background. Those in the training set that are most like the background (i e, most unlike the rest of the training set) are considered anomalous. Although by their nature, anomalies do not permit a positive definition (if I knew what they were, I wouldn't call them anomalies), one can make 'negative definitions' (I can say what does not qualify as an interesting anomaly). By choosing different resampling schemes, one can identify different kinds of anomalies. For multispectral images, anomalous pixels correspond to locations on the ground with unusual spectral signatures or, depending on how feature sets are constructed, unusual spatial textures.

Theiler, J. P. (James P.); Cai, D. (David)

2003-01-01T23:59:59.000Z

35

Multispectral Imaging At Long Valley Caldera Area (Martin, Et Al., 2004) |  

Open Energy Info (EERE)

Martin, Et Al., 2004) Martin, Et Al., 2004) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Multispectral Imaging At Long Valley Caldera Area (Martin, Et Al., 2004) Exploration Activity Details Location Long Valley Caldera Area Exploration Technique Multispectral Imaging Activity Date Usefulness useful DOE-funding Unknown Notes At shallow depths in the caldera References B. Martin, E. Silver, W. Pickles, P. Cocks (Unknown) Hyperspectral Mineral Mapping In Support Of Geothermal Exploration- Examples From Long Valley Caldera, Ca And Dixie Valley, Nv, Usa Retrieved from "http://en.openei.org/w/index.php?title=Multispectral_Imaging_At_Long_Valley_Caldera_Area_(Martin,_Et_Al.,_2004)&oldid=511009" Categories: Exploration Activities DOE Funded

36

Multispectral Imaging At The Needles Area (Kratt, Et Al., 2005) | Open  

Open Energy Info (EERE)

Multispectral Imaging At The Needles Area (Kratt, Et Al., 2005) Multispectral Imaging At The Needles Area (Kratt, Et Al., 2005) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Multispectral Imaging At The Needles Area (Kratt, Et Al., 2005) Exploration Activity Details Location The Needles Area Exploration Technique Multispectral Imaging Activity Date Usefulness not indicated DOE-funding Unknown Notes Over 2000 km2 of 5-m resolution Hymap hyperspectral data was acquired in 2004. Subsequent image processing and data analysis has identified reflectance spectra for alunite, kaolinite/halloysite, illite, gypsum, vegetation, and carbonate. A portable spectrometer is being used for in situ validation, along with laboratory measurements and x-ray diffraction analyses of samples collected in teh field. We are in the process of

37

Polarization-dependent wavelength-selective structures for multispectral polarimetric infrared imaging  

E-Print Network (OSTI)

The need for compact, rugged, low-cost multispectral-polarimetric filtering technology exists in both the civilian and defense communities. Such technology can be used for object detection, object recognition, and image ...

Dunmeyer, David Richard, 1978-

2007-01-01T23:59:59.000Z

38

Image quality degradation and retrieval errors introduced by registration and interpolation of multispectral digital images  

SciTech Connect

Full utilization of multispectral data acquired by whiskbroom and pushbroom imagers requires that the individual channels be registered accurately. Poor registration introduces errors which can be significant, especially in high contrast areas such as boundaries between regions. We simulate the acquisition of multispectral imagery in order to estimate the errors that are introduced by co-registration of different channels and interpolation within the images. We compute the Modulation Transfer Function (MTF) and image quality degradation brought about by fractional pixel shifting and calculate errors in retrieved quantities (surface temperature and water vapor) that occur as a result of interpolation. We also present a method which might be used to estimate sensor platform motion for accurate registration of images acquired by a pushbroom scanner.

Henderson, B.G.; Borel, C.C.; Theiler, J.P.; Smith, B.W.

1996-04-01T23:59:59.000Z

39

Calibration Accuracy Of Aerial Multispectral Reflectance Images And Estimation Of Error Sources  

E-Print Network (OSTI)

: We have performed a systematic study of the calibration accuracy of multispectral aerial reflectance images. The study is part of the improvement of change detection for aerial and satellite multispectral images. It is based on (a) a multitemporal image data set from the multispectral airborne scanner Daedalus AADS 1268 and (b) simultaneously made ground based hyperspectral reflectance measurements. Reflectance images were obtained from the raw images by processing with the program package SENSAT-5, using standard urban atmospheres in the MODTRAN code. The systematic uncertainty of the resulting reflectance spectra is mainly due to the uncertainty in the atmospheric parameters. It can be reduced by fitting the Daedalus spectra to ground truth hyperspectral reflectance measurements of selected surfaces. The resulting uncertainty oe ae =ae of the reflectance ae is estimated to be 11.0 % on average. KEY WORDS: Remote sensing, Reflectance, Error sources 1 INTRODUCTION Remotely sensed ...

Andre Rothkirch; Martin Kollewe; Hartwig Spitzer

1998-01-01T23:59:59.000Z

40

Multispectral Imaging At Brady Hot Springs Area (Laney, 2005) | Open Energy  

Open Energy Info (EERE)

Multispectral Imaging At Brady Hot Springs Area Multispectral Imaging At Brady Hot Springs Area (Laney, 2005) Exploration Activity Details Location Brady Hot Springs Area Exploration Technique Multispectral Imaging Activity Date Usefulness useful DOE-funding Unknown Notes Remote Sensing for Exploration and Mapping of Geothermal Resources, Wendy Calvin, 2005. Task 1: Detailed analysis of hyperspectral imagery obtained in summer of 2003 over Brady's Hot Springs region was completed and validated (Figure 1). This analysis provided a local map of both sinter and tufa deposits surrounding the Ormat plant, identified fault extensions not previously recognized from field mapping and has helped constrain where to put additional wells that were drilled at the site. Task 2: Initial analysis of Landsat and ASTER data for Buffalo Valley and Pyramid Lake was

Note: This page contains sample records for the topic "imaging multispectral thermal" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Multispectral Imaging At Long Valley Caldera Area (Pickles, Et Al., 2001) |  

Open Energy Info (EERE)

source source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit History Facebook icon Twitter icon » Multispectral Imaging At Long Valley Caldera Area (Pickles, Et Al., 2001) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Multispectral Imaging At Long Valley Caldera Area (Pickles, Et Al., 2001) Exploration Activity Details Location Long Valley Caldera Area Exploration Technique Multispectral Imaging Activity Date Usefulness useful DOE-funding Unknown Notes At shallow depths in the caldera References W. L. Pickles, P. W. Kasamayer, B. A. Martini, D. C. Potts, E. A. Silver (2001) Geobotanical Remote Sensing For Geothermal Exploration

42

Multispectral Imaging At Dixie Meadows Area (Pickles, Et Al., 2003) | Open  

Open Energy Info (EERE)

Dixie Meadows Area (Pickles, Et Al., 2003) Dixie Meadows Area (Pickles, Et Al., 2003) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Multispectral Imaging At Dixie Meadows Area (Pickles, Et Al., 2003) Exploration Activity Details Location Dixie Meadows Area Exploration Technique Multispectral Imaging Activity Date Usefulness useful DOE-funding Unknown References W. L. Pickles, G. D. Nash, W. M. Calvin, B. A. Martini, P. A. Cocks, T. Kenedy-Bowdoin, R. B. Mac Knight, E. A. Silver, D. C. Potts, W. Foxall, P. Kasamayer, A. F. Waibel (2003) Geobotanical Remote Sensing Applied To Targeting New Geothermal Resource Locations In The Us Basin And Range With A Focus On Dixie Meadows, Nv Retrieved from "http://en.openei.org/w/index.php?title=Multispectral_Imaging_At_Dixie_Meadows_Area_(Pickles,_Et_Al.,_2003)&oldid=511005"

43

Visualizing Chemical Compositions and Kinetics of Sol-Gel by Near-Infrared Multispectral Imaging  

E-Print Network (OSTI)

Visualizing Chemical Compositions and Kinetics of Sol-Gel by Near-Infrared Multispectral Imaging in order to determine the presence of any chemical and kinetic inhomogeneity. Unfortunately, to date, NIR to determine the chemical and kinetic inho- mogeneity of sol-gel. Preliminary results on the kinetics of sol

Reid, Scott A.

44

Primer on Use of Multi-Spectral and Infra Red Imaging for On-Site Inspections  

Science Conference Proceedings (OSTI)

The purpose of an On-Site Inspection (OSI) is to determine whether a nuclear explosion has occurred in violation of the Comprehensive Nuclear Test Ban Treaty (CTBT), and to gather information which might assist in identifying the violator (CTBT, Article IV, Paragraph 35) Multi-Spectral and Infra Red Imaging (MSIR) is allowed by the treaty to detect observables which might help reduce the search area and thus expedite an OSI and make it more effective. MSIR is permitted from airborne measurements, and at and below the surface to search for anomalies and artifacts (CTBT, Protocol, Part II, Paragraph 69b). The three broad types of anomalies and artifacts MSIR is expected to be capable of observing are surface disturbances (disturbed earth, plant stress or anomalous surface materials), human artifacts (man-made roads, buildings and features), and thermal anomalies. The purpose of this Primer is to provide technical information on MSIR relevant to its use for OSI. It is expected that this information may be used for general background information, to inform decisions about the selection and testing of MSIR equipment, to develop operational guidance for MSIR use during an OSI, and to support the development of a training program for OSI Inspectors. References are provided so readers can pursue a topic in more detail than the summary information provided here. The following chapters will provide more information on how MSIR can support an OSI (Section 2), a short summary what Multi-Spectral Imaging and Infra Red Imaging is (Section 3), guidance from the CTBT regarding the use of MSIR (Section 4), and a description of several nuclear explosion scenarios (Section 5) and consequent observables (Section 6). The remaining sections focus on practical aspects of using MSIR for an OSI, such as specification and selection of MSIR equipment, operational considerations for deployment of MISR equipment from an aircraft, and the conduct of field exercises to mature MSIR for an OSI. Finally, an appendix provides detail describing the magnitude and spatial extent of the surface shock expected from an underground nuclear explosion. If there is a seismic event or other data to suggest there has been a nuclear explosion in violation of the CTBT, an OSI may be conducted to determine whether a nuclear explosion has occurred and to gather information which may be useful in identifying the party responsible for conducting the explosion. The OSI must be conducted in the area where the event that triggered the inspection request occurred, and the inspected area must not exceed 1,000 square kilometers, or be more than 50 km on aside (CTBT Protocol, Part II, Paragraphs 2 and 3). One of the guiding principles for an inspection is that it be effective, minimally intrusive, timely, and cost-effective [Hawkins, Feb 1998]. In that context, MSIR is one of several technologies that can be used during an aircraft overflight to identify ground regions of high interest in a timely and cost-effective manner. This allows for an optimized inspection on the ground. The primary purpose for MSIR is to identify artifacts and anomalies that might be associated with a nuclear explosion, and to use the location of those artifacts and anomalies to reduce the search area that must be inspected from the ground. The MSIR measurements can have additional utility. The multi-spectral measurements of the ground can be used for terrain classification, which can aid in geological characterization of the Inspected Area. In conditions of where light smoke or haze is present, long-wave infrared imaging can provide better imaging of the ground than is possible with standard visible imagery.

Henderson, J R

2010-10-26T23:59:59.000Z

45

Satellite-Derived Sea Surface Temperatures: Evaluation of GOES-8 and GOES-9 Multispectral Imager Retrieval Accuracy  

Science Conference Proceedings (OSTI)

Sea surface temperature (SST) retrieval accuracy from the multispectral imager on the new generation of GOES satellites is analyzed. Equations for two and three infrared channels are empirically derived using cloud-free satellite radiances ...

Douglas A. May; Walter O. Osterman

1998-06-01T23:59:59.000Z

46

Multispectral Imaging At Buffalo Valley Hot Springs Area (Littlefield...  

Open Energy Info (EERE)

Spectral Imaging Sensor ASTER Usefulness useful DOE-funding Unknown Notes ASTER airborne remote sensing. References E. Littlefield, W. Calvin (2009) Remote Sensing For Geothermal...

47

Active multispectral illumination and image fusion for retinal microsurgery  

Science Conference Proceedings (OSTI)

It has been shown that white light exposure during retinal microsurgeries is detrimental to patients. To address this problem, we present a novel device and image processing tool, which can be used to significantly reduce the amount of phototoxicity ...

Raphael Sznitman; Seth Billings; Diego Rother; Daniel Mirota; Yi Yang; Jim Handa; Peter Gehlbach; Jin U. Kang; Gregory D. Hager; Russell Taylor

2010-06-01T23:59:59.000Z

48

Multi-Spectral imaging of vegetation for detecting CO2 leaking from underground  

Science Conference Proceedings (OSTI)

Practical geologic CO{sub 2} sequestration will require long-term monitoring for detection of possible leakage back into the atmosphere. One potential monitoring method is multi-spectral imaging of vegetation reflectance to detect leakage through CO{sub 2}-induced plant stress. A multi-spectral imaging system was used to simultaneously record green, red, and near-infrared (NIR) images with a real-time reflectance calibration from a 3-m tall platform, viewing vegetation near shallow subsurface CO{sub 2} releases during summers 2007 and 2008 at the Zero Emissions Research and Technology field site in Bozeman, Montana. Regression analysis of the band reflectances and the Normalized Difference Vegetation Index with time shows significant correlation with distance from the CO{sub 2} well, indicating the viability of this method to monitor for CO{sub 2} leakage. The 2007 data show rapid plant vigor degradation at high CO{sub 2} levels next to the well and slight nourishment at lower, but above-background CO{sub 2} concentrations. Results from the second year also show that the stress response of vegetation is strongly linked to the CO{sub 2} sink-source relationship and vegetation density. The data also show short-term effects of rain and hail. The real-time calibrated imaging system successfully obtained data in an autonomous mode during all sky and daytime illumination conditions.

Rouse, J.H.; Shaw, J.A.; Lawrence, R.L.; Lewicki, J.L.; Dobeck, L.M.; Repasky, K.S.; Spangler, L.H.

2010-06-01T23:59:59.000Z

49

THERMAL NEUTRON BACKSCATTER IMAGING.  

DOE Green Energy (OSTI)

Objects of various shapes, with some appreciable hydrogen content, were exposed to fast neutrons from a pulsed D-T generator, resulting in a partially-moderated spectrum of backscattered neutrons. The thermal component of the backscatter was used to form images of the objects by means of a coded aperture thermal neutron imaging system. Timing signals from the neutron generator were used to gate the detection system so as to record only events consistent with thermal neutrons traveling the distance between the target and the detector. It was shown that this time-of-flight method provided a significant improvement in image contrast compared to counting all events detected by the position-sensitive {sup 3}He proportional chamber used in the imager. The technique may have application in the detection and shape-determination of land mines, particularly non-metallic types.

VANIER,P.; FORMAN,L.; HUNTER,S.; HARRIS,E.; SMITH,G.

2004-10-16T23:59:59.000Z

50

Comparing robust and physics-based sea surface temperature retrievals for high resolution, multi-spectral thermal sensors using one or multiple looks  

SciTech Connect

With the advent of multi-spectral thermal imagers such as EOS's ASTER high spatial resolution thermal imagery of the Earth's surface will soon be a reality. Previous high resolution sensors such as Landsat 5 had only one spectral channel in the thermal infrared and its utility to determine absolute sea surface temperatures was limited to 6-8 K for water warmer than 25 deg C. This inaccuracy resulted from insufficient knowledge of the atmospheric temperature and water vapor, inaccurate sensor calibration, and cooling effects of thin high cirrus clouds. The authors will present two studies of algorithms and compare their performance. The first algorithm they call robust since it retrieves sea surface temperatures accurately over a fairly wide range of atmospheric conditions using linear combinations of nadir and off-nadir brightness temperatures. The second they call physics-based because it relies on physics-based models of the atmosphere. It attempts to come up with a unique sea surface temperature which fits one set of atmospheric parameters.

Borel, C.C.; Clodius, W.B.; Szymanski, J.J.; Theiler, J.P.

1999-04-04T23:59:59.000Z

51

A multispectral scanner survey of the Rocky Flats Environmental Technology Site and surrounding area, Golden, Colorado  

SciTech Connect

Aerial multispectral scanner imagery was collected of the Rocky Flats Environmental Technology Site in Golden, Colorado, on June 3, 5, 6, and 7, 1994, using a Daedalus AADS1268 multispectral scanner and coincident aerial color and color infrared photography. Flight altitudes were 4,500 feet (1372 meters) above ground level to match prior 1989 survey data; 2,000 feet (609 meters) above ground level for sitewide vegetation mapping; and 1,000 feet (304 meters) above ground level for selected areas of special interest. A multispectral survey was initiated to improve the existing vegetation classification map, to identify seeps and springs, and to generate ARC/INFO Geographic Information System compatible coverages of the vegetation and wetlands for the entire site including the buffer zone. The multispectral scanner imagery and coincident aerial photography were analyzed for the detection, identification, and mapping of vegetation and wetlands. The multispectral scanner data were processed digitally while the color and color infrared photography were manually photo-interpreted to define vegetation and wetlands. Several standard image enhancement techniques were applied to the multispectral scanner data to assist image interpretation. A seep enhancement was applied and a color composite consisting of multispectral scanner channels 11, 7, and 5 (thermal infrared, mid-infrared, and red bands, respectively) proved most useful for detecting seeps, seep zones, and springs. The predawn thermal infrared data were also useful in identifying and locating seeps. The remote sensing data, mapped wetlands, and ancillary Geographic Information System compatible data sets were spatially analyzed for seeps.

Brewster, S.B. Jr.; Brickey, D.W.; Ross, S.L.; Shines, J.E.

1997-04-01T23:59:59.000Z

52

Resonant-cavity-enhanced multispectral infrared photodetectors for monolithic integration on silicon  

E-Print Network (OSTI)

Multispectral infrared (IR) detection has been widely employed for numerous applications including hyperspectral imaging, IR spectroscopy, and target identification. Traditional multispectral detection technology is based ...

Wang, Jianfei, Ph. D. Massachusetts Institute of Technology

2010-01-01T23:59:59.000Z

53

A multi-spectral imaging system for geo-spatial applications  

Science Conference Proceedings (OSTI)

The integration of remote sensing and geographic information systems (GIS) in environmental applications has become increasingly common in recent years. Remotely sensed images are an important data source for environmental GIS applications and conversely ... Keywords: Imaging systems, computing applications, environmental systems, geographic information systems, prototyping

Carl Steidley; Ray Bachnak; R. Stephen Dannelly; Rahul Kulkarni; Chad Mayfield

2005-01-01T23:59:59.000Z

54

Radiography used to image thermal explosions  

NLE Websites -- All DOE Office Websites (Extended Search)

Radiography used to image thermal explosions Radiography used to image thermal explosions Radiography used to image thermal explosions Researchers have gained an understanding of the mechanism of thermal explosions and have created a model capturing the stages of the explosion. October 9, 2012 Tabletop X-ray radiography of a thermal explosion. Tabletop X-ray radiography of a thermal explosion. Researchers have gained an understanding of the mechanism of thermal explosions and have created a model capturing the stages of the explosion. Proton radiography (pRad) at LANSCE imaged thermal explosions at high speeds to provide a real-time look at how an explosion unfolds and releases its energy. Specifically, it is important to know the range of temperature over which ignition may occur and the subsequent power of the explosion.

55

Sensitive interferometric video thermal wave imager  

Science Conference Proceedings (OSTI)

A new method of parallel thermal wave imaging is demonstrated in which the thermal wave image of a heated sample is converted into an optical phase image which is sensitively probed by a TwymanGreen interferometer. The sample is mounted onto an assembly of optical layers which acts as a temperature sensitive mirror.Heat conduction from the sample to this mirror results in a two?dimensional distribution of optical phase which is probed broadfield by the interferometer. The resulting transmission thermal wave image has characteristics analogous to those of photopyroelectric images. The interferogram produced in the interferometer may be recorded by videography

J. F. Power

1996-01-01T23:59:59.000Z

56

On the focusing of thermal images  

Science Conference Proceedings (OSTI)

In this paper we present a new thermographic image database, suitable for the analysis of automatic focusing measures. This database contains the images of 10 scenes, each of which is represented once for each of 96 different focus positions. Using this ... Keywords: Database, Focus, Image quality, Thermal image

Marcos Faundez-Zanuy; Ji? Mekyska; Virginia Espinosa-Dur

2011-08-01T23:59:59.000Z

57

Thermal Imaging Control of Furnaces and Combustors  

Science Conference Proceedings (OSTI)

The object if this project is to demonstrate and bring to commercial readiness a near-infrared thermal imaging control system for high temperature furnaces and combustors. The thermal imaging control system, including hardware, signal processing, and control software, is designed to be rugged, self-calibrating, easy to install, and relatively transparent to the furnace operator.

David M. Rue; Serguei Zelepouga; Ishwar K. Puri

2003-02-28T23:59:59.000Z

58

Thermal imaging diagnostics of high-current electron beams  

SciTech Connect

The thermal imaging diagnostics of measuring pulsed electron beam energy density is presented. It provides control of the electron energy spectrum and a measure of the density distribution of the electron beam cross section, the spatial distribution of electrons with energies in the selected range, and the total energy of the electron beam. The diagnostics is based on the thermal imager registration of the imaging electron beam thermal print in a material with low bulk density and low thermal conductivity. Testing of the thermal imaging diagnostics has been conducted on a pulsed electron accelerator TEU-500. The energy of the electrons was 300-500 keV, the density of the electron current was 0.1-0.4 kA/cm{sup 2}, the duration of the pulse (at half-height) was 60 ns, and the energy in the pulse was up to 100 J. To register the thermal print, a thermal imager Fluke-Ti10 was used. Testing showed that the sensitivity of a typical thermal imager provides the registration of a pulsed electron beam heat pattern within one pulse with energy density over 0.1 J/cm{sup 2} (or with current density over 10 A/cm{sup 2}, pulse duration of 60 ns and electron energy of 400 keV) with the spatial resolution of 0.9-1 mm. In contrast to the method of using radiosensitive (dosimetric) materials, thermal imaging diagnostics does not require either expensive consumables, or plenty of processing time.

Pushkarev, A.; Kholodnaya, G.; Sazonov, R.; Ponomarev, D. [Tomsk Polytechnic University, 30 Lenin Ave., Tomsk, 634050 (Russian Federation)

2012-10-15T23:59:59.000Z

59

Snow/Cloud Discrimination with Multispectral Satellite Measurements  

Science Conference Proceedings (OSTI)

An algorithm is developed and evaluated for discriminating between clouds, snow-covered land and snow-free land in satellite image data. The multispectral technique uses daytime images of NOAA AVHRR channels 1 (0.63 ?m), 3 (3.7 ?m), and 4 (11.0 ...

Robert C. Allen Jr.; Philip A. Durkee; Carlyle H. Wash

1990-10-01T23:59:59.000Z

60

Automated rapid thermal imaging systems technology  

E-Print Network (OSTI)

A major source of energy savings occurs on the thermal envelop of buildings, which amounts to approximately 10% of annual energy usage in the United States. To pursue these savings, energy auditors use closed loop energy ...

Phan, Long N., 1976-

2012-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "imaging multispectral thermal" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

GOES Multispectral Rainfall Algorithm (GMSRA)  

Science Conference Proceedings (OSTI)

A multispectral approach is used to optimize the identification of raining clouds located at a given altitude estimated from the cloud-top temperature. The approach combines information from five channels on the National Oceanic and Atmospheric ...

Mamoudou B. Ba; Arnold Gruber

2001-08-01T23:59:59.000Z

62

THERMAL IMAGING OF ACTIVE MAGNETIC REGERNERATOR MCE MATERIALS DURING OPERATION  

SciTech Connect

An active magnetic regenerator (AMR) prototype was constructed that incorporates a Gd sheet into the regenerator wall to enable visualization of the system s thermal transients. In this experiment, the thermal conditions inside the AMR are observed under a variety of operating conditions. An infrared (IR) camera is employed to visualize the thermal transients within the AMR. The IR camera is used to visually and quantitatively evaluate the temperature difference and thus giving means to calculate the performance of the system under the various operating conditions. Thermal imaging results are presented for two differing experimental test runs. Real time imaging of the thermal state of the AMR has been conducted while operating the system over a range of conditions. A 1 Tesla twin-coil electromagnet (situated on a C frame base) is used for this experiment such that all components are stationary during testing. A modular, linear reciprocating system has been realized in which the effects of regenerator porosity and utilization factor can be investigated. To evaluate the performance variation in porosity and utilization factor the AMR housing was constructed such that the plate spacing of the Gd sheets may be varied. Each Gd sheet has dimensions of 38 mm wide and 66 mm long with a thickness of 1 mm and the regenerator can hold a maximum of 29 plates with a spacing of 0.25 mm. Quantitative and thermal imaging results are presented for several regenerator configurations.

Shassere, Benjamin [ORNL; West, David L [ORNL; Abdelaziz, Omar [ORNL; Evans III, Boyd Mccutchen [ORNL

2012-01-01T23:59:59.000Z

63

Correlated two-photon imaging with true thermal light  

E-Print Network (OSTI)

We report the first experimental demonstration of two-photon correlated imaging with true thermal light from a hollow cathode lamp. The coherence time of the source is much shorter than that of previous experiments using random scattered light from a laser. A two-pinhole mask was used as object, and the corresponding thin lens equation was well satisfied. Since thermal light sources are easier to obtain and measure than entangled light it is conceivable that they may be used in special imaging applications.

Da Zhang; Xi-Hao Chen; Yan-Hua Zhai; Ling-An Wu

2005-03-14T23:59:59.000Z

64

Multi-spectral band selection for satellite-based systems  

Science Conference Proceedings (OSTI)

The design of satellite based multispectral imaging systems requires the consideration of a number of tradeoffs between cost and performance. The authors have recently been involved in the design and evaluation of a satellite based multispectral sensor operating from the visible through the long wavelength IR. The criteria that led to some of the proposed designs and the modeling used to evaluate and fine tune the designs will both be discussed. These criteria emphasized the use of bands for surface temperature retrieval and the correction of atmospheric effects. The impact of cost estimate changes on the final design will also be discussed.

Clodius, W.B.; Weber, P.G.; Borel, C.C.; Smith, B.W.

1998-09-01T23:59:59.000Z

65

Multicolor Underwater Imaging Techniques.  

E-Print Network (OSTI)

??Studies were conducted on multispectral polarimetric subtraction imaging techniques for underwater imaging that use a broadband light source. The main objective of this study was (more)

Waggoner, Douglas Scott

2007-01-01T23:59:59.000Z

66

Thermal imaging experiments on ANACONDA ion beam generator  

Science Conference Proceedings (OSTI)

The thermal imaging technique was used in two experimental measurements. First, the ion intensity distribution on the anode surface was observed from different angles by using a multi-pinhole camera. Second, the plume from a target intercepting the beam was visualized by observing the distribution of temperature increase on a thin plate hit by the plume.

Jiang, W.; Yatsui, K. [Nagaoka Univ. of Technology (Japan). Lab. of Beam Technology; Olson, J.C.; Davis, H.A. [Los Alamos National Lab., NM (United States)

1996-12-31T23:59:59.000Z

67

Algorithm of feature estimation for real time objects detection in thermal images  

Science Conference Proceedings (OSTI)

Objects detection in thermal or infrared images is an actual and necessary problem in wide range of thermo visual systems applications. The goal of this article is to select a suitable set of features for objects detection in thermal images. Using the ... Keywords: features estimation, infrared images, real time objects detection, thermal images

Snejana Pleshkova

2011-12-01T23:59:59.000Z

68

Thermal Imaging of Medical Saw Blades and Guides  

SciTech Connect

Better Than New, LLC., has developed a surface treatment to reduce the friction and wear of orthopedic saw blades and guides. The medical saw blades were thermally imaged while sawing through fresh animal bone and an IR camera was used to measure the blade temperature as it exited the bone. The thermal performance of as-manufactured saw blades was compared to surface-treated blades, and a freshly used blade was used for temperature calibration purposes in order to account for any emissivity changes due to organic transfer layers. Thermal imaging indicates that the treated saw blades cut faster and cooler than untreated blades. In orthopedic surgery, saw guides are used to perfectly size the bone to accept a prosthesis. However, binding can occur between the blade and guide because of misalignment. This condition increases the saw blade temperature and may result in tissue damage. Both treated ad untreated saw guides were also studied. The treated saw guide operated at a significantly lower temperature than untreated guide. Saw blades and guides that operate at a cooler temperature are expected to reduce the amount of tissue damage (thermal necrosis) and may reduce the number of post-operative complications.

Dinwiddie, Ralph Barton [ORNL; Steffner, Thomas E [ORNL

2007-01-01T23:59:59.000Z

69

Chemical detection using the airborne thermal infrared imaging spectrometer (TIRIS)  

SciTech Connect

A methodology is described for an airborne, downlooking, longwave infrared imaging spectrometer based technique for the detection and tracking of plumes of toxic gases. Plumes can be observed in emission or absorption, depending on the thermal contrast between the vapor and the background terrain. While the sensor is currently undergoing laboratory calibration and characterization, a radiative exchange phenomenology model has been developed to predict sensor response and to facilitate the sensor design. An inverse problem model has also been developed to obtain plume parameters based on sensor measurements. These models, the sensors, and ongoing activities are described.

Gat, N.; Subramanian, S.; Sheffield, M.; Erives, H. [Opto-Knowledge Systems, Inc. (United States); Barhen, J. [Oak Ridge National Lab., TN (United States)

1997-04-01T23:59:59.000Z

70

An Interactive Method for Processing and Display of Sea-Surface Temperature Fields Using VAS Multispectral Data  

Science Conference Proceedings (OSTI)

A technique for interactively producing sea-surface temperatures (SST)from VAS multispectral radiance observations and displaying the derived field is outlined. High-resolution composite images using data from several times per day and over a ...

John J. Bates; William L. Smith; Gary S. Wade; Harold M. Woo1f

1987-06-01T23:59:59.000Z

71

Theoretical scheme of thermal-light many-ghost imaging by Nth-order intensity correlation  

Science Conference Proceedings (OSTI)

In this paper, we propose a theoretical scheme of many-ghost imaging in terms of Nth-order correlated thermal light. We obtain the Gaussian thin lens equations in the many-ghost imaging protocol. We show that it is possible to produce N-1 ghost images of an object at different places in a nonlocal fashion by means of a higher order correlated imaging process with an Nth-order correlated thermal source and correlation measurements. We investigate the visibility of the ghost images in the scheme and obtain the upper bounds of the visibility for the Nth-order correlated thermal-light ghost imaging. It is found that the visibility of the ghost images can be dramatically enhanced when the order of correlation becomes larger. It is pointed out that the many-ghost imaging phenomenon is an observable physical effect induced by higher order coherence or higher order correlations of optical fields.

Liu Yingchuan [Key Laboratory of Low-Dimensional Quantum Structures and Quantum Control of Ministry of Education, and Department of Physics, Hunan Normal University, Changsha 410081 (China); College of Mathematics and Physics, University of South China, Hengyang 421001 (China); Kuang Leman [Key Laboratory of Low-Dimensional Quantum Structures and Quantum Control of Ministry of Education, and Department of Physics, Hunan Normal University, Changsha 410081 (China)

2011-05-15T23:59:59.000Z

72

Cloud detection of MODIS multispectral images  

Science Conference Proceedings (OSTI)

Methods coming from statistics and pattern recognition to estimate the cloud mask from radiance measured by visible and infrared sensors onboard satellites are gaining greater and greater consideration for their ability to properly exploit the ...

Loredana Murino; Umberto Amato; Maria Francesca Carfora; Anestis Antoniadis; Bormin Huang; W. Paul Menzel; Carmine Serio

73

Thermal Imaging of Canals for Remote Detection of Leaks: Evaluation in the United Irrigation District  

E-Print Network (OSTI)

This report summarizes our initial analysis of the potential of thermal imaging for detecting leaking canals and pipelines. Thermal imagery (video format) was obtained during a fly over of a portion of the main canal of United Irrigation District. The video was processed to produce individual images, and 45 potential sites were identified as having possible canal leakage problems (see Appendix I for all 45 thermal images). District Management System Team personnel traveled to 11 of the 45 sites to determine if canal leakage was actually occurring. Of the 11 sites, 10 had leakage problems. Thus, thermal image analysis had a success rate of 91% for leak detection. Two sites had leaks classified as severe by the DMS Team. This report also provides a detailed analysis of 4 sites, 3 with leaks and 1 without. For each site, photographs are included showing the source of the leak and/or condition of the canal segment. A literature review of thermal imagery for leak detection is included in Appendix II. Our findings and recommendations are as following: 1. thermal imaging is a promising technique for evaluation of canal conditions and leak detection; 2. the district provide should provide personnel to help the DMS Team verify the remaining 34 sites; and 3. the district should consider correcting the problems identified at sites 7 and 8.

Huang, Yanbo; Fipps, Guy

2008-11-01T23:59:59.000Z

74

SPECTRUM analysis of multispectral imagery in conjunction with wavelet/KLT data compression  

SciTech Connect

The data analysis program, SPECTRUM, is used for fusion, visualization, and classification of multi-spectral imagery. The raw data used in this study is Landsat Thematic Mapper (TM) 7-channel imagery, with 8 bits of dynamic range per channel. To facilitate data transmission and storage, a compression algorithm is proposed based on spatial wavelet transform coding and KLT decomposition of interchannel spectral vectors, followed by adaptive optimal multiband scalar quantization. The performance of SPECTRUM clustering and visualization is evaluated on compressed multispectral data. 8-bit visualizations of 56-bit data show little visible distortion at 50:1 compression and graceful degradation at higher compression ratios. Two TM images were processed in this experiment: a 1024 x 1024-pixel scene of the region surrounding the Chernobyl power plant, taken a few months before the reactor malfunction, and a 2048 x 2048 image of Moscow and surrounding countryside.

Bradley, J.N.; Brislawn, C.M.

1993-12-01T23:59:59.000Z

75

Combining a thermal-imaging diagnostic with an existing imaging VISAR diagnostic at the National Ignition Facility (NIF)  

Science Conference Proceedings (OSTI)

Optical diagnostics are currently being designed to analyze high-energy density physics experiments at the National Ignition Facility (NIF). Two independent line-imaging Velocity Interferometer System for Any Reflector (VISAR) interferometers have been fielded to measure shock velocities, breakout times, and emission of targets having sizes of 1-5 mm. An 8-inch-diameter, fused silica triplet lens collects light at f/3 inside the 30-foot-diameter NIF vacuum chamber. VISAR recordings use a 659.5-nm probe laser. By adding a specially coated beam splitter to the interferometer table, light at wavelengths from 540 to 645 nm is spilt into a thermal-imaging diagnostic. Because fused silica lenses are used in the first triplet relay, the intermediate image planes for different wavelengths separate by considerable distances. A corrector lens on the interferometer table reunites these separated wavelength planes to provide a good image. Thermal imaging collects light at f/5 from a 2-mm object placed at Target Chamber Center (TCC). Streak cameras perform VISAR and thermal-imaging recording. All optical lenses are on kinematic mounts so that pointing accuracy of the optical axis may be checked. Counter-propagating laser beams (orange and red) are used to align both diagnostics. The red alignment laser is selected to be at the 50 percent reflection point of the beam splitter. This alignment laser is introduced at the recording streak cameras for both diagnostics and passes through this special beam splitter on its way into the NIF vacuum chamber.

Malone, R; Celeste, J; Celliers, P; Frogget, B; Guyton, R L; Kaufman, M; Lee, T; MacGowan, B; Ng, E W; Reinbachs, I P; Robinson, R B; Seppala, L; Tunnell, T W; Watts, P

2005-07-07T23:59:59.000Z

76

Combining a thermal-imaging diagnostic with an existing imaging VISAR diagnostic at the National Ignition Facility (NIF)  

Science Conference Proceedings (OSTI)

Optical diagnostics are currently being designed to analyze high-energy density physics experiments at the National Ignition Facility (NIF). Two independent line-imaging Velocity Interferometer System for Any Reflector (VISAR) interferometers have been fielded to measure shock velocities, breakout times, and emission of targets having sizes of 15 mm. An 8-inch-diameter, fused silica triplet lens collects light at f/3 inside the 30-foot-diameter NIF vacuum chamber. VISAR recordings use a 659.5-nm probe laser. By adding a specially coated beam splitter to the interferometer table, light at wavelengths from 540 to 645 nm is spilt into a thermal-imaging diagnostic. Because fused silica lenses are used in the first triplet relay, the intermediate image planes for different wavelengths separate by considerable distances. A corrector lens on the interferometer table reunites these separated wavelength planes to provide a good image. Thermal imaging collects light at f/5 from a 2-mm object placed at Target Chamber Center (TCC). Streak cameras perform VISAR and thermal-imaging recording. All optical lenses are on kinematic mounts so that pointing accuracy of the optical axis may be checked. Counter-propagating laser beams (orange and red) are used to align both diagnostics. The red alignment laser is selected to be at the 50 percent reflection point of the beam splitter. This alignment laser is introduced at the recording streak cameras for both diagnostics and passes through this special beam splitter on its way into the NIF vacuum chamber.

Robert M. Malone; John R. Celesteb; Peter M. Celliers; Brent C. Froggeta; Robert L. Guyton; Morris I. Kaufman; Tony L. Lee; Brian J. MacGowan; Edmund W. Ng; Imants P. Reinbachs; Ronald B. Robinson; Lynn G. Seppala; Tom W. Tunnell; Phillip W. Watts

2005-01-01T23:59:59.000Z

77

Imaging Fluid Flow in Geothermal Wells Using Distributed Thermal Perturbation Sensing  

SciTech Connect

The objective of Task 2 is to develop a numerical method for the efficient and accurate analysis of distributed thermal perturbation sensing (DTPS) data for (1) imaging flow profiles and (2) in situ determination of thermal conductivities and heat fluxes. Numerical forward and inverse modeling is employed to: (1) Examine heat and fluid flow processes near a geothermal well under heating and cooling conditions; (2) Demonstrate ability to interpret DTPS thermal profiles with acceptable estimation uncertainty using inverse modeling of synthetic temperature data; and (3) Develop template model and analysis procedure for the inversion of temperature data collected during a thermal perturbation test using fiber-optic distributed temperature sensors. This status report summarizes initial model developments and analyses.

Freifeld, B.; Finsterle, S.

2010-12-10T23:59:59.000Z

78

Uncooled thin film infrared imaging device with aerogel thermal isolation: Deposition and planarization techniques  

Science Conference Proceedings (OSTI)

The authors have successfully integrated a thermally insulating silica aerogel thin film into a new uncooled monolithic thin film infrared (IR) imaging device. Compared to other technologies (bulk ceramic and microbridge), use of an aerogel layer provides superior thermal isolation of the pyroelectric imaging element from the relatively massive heat sinking integrated circuit. This results in significantly higher thermal and temporal resolutions. They have calculated noise equivalent temperature differences of 0.04--0.10 C from a variety of Pb{sub x}Zr{sub y}Ti{sub 1{minus}y}O{sub 3} (PZT) and Pb{sub x}La{sub 1{minus}x}Zr{sub y}Ti{sub 1{minus}y}O{sub 3} (PLZT) pyroelectric imaging elements in monolithic structures. In addition, use of aerogels results in an easier, less expensive fabrication process and a more robust device. Fabrication of these monolithic devices entails sol-gel deposition of the aerogel, sputter deposition of the electrodes, and solution chemistry deposition of the pyroelectric imaging elements. Uniform pyroelectric response is achieved across the device by use of appropriate planarization techniques. These deposition and planarization techniques are described. Characterization of the individual layers and monolithic structure using scanning electron microscopy, atomic force microscopy and Byer-Roundy techniques also is discussed.

Ruffner, J.A.; Clem, P.G.; Tuttle, B.A.; Brinker, C.J. [Sandia National Labs., Albuquerque, NM (United States); Sriram, C.S. [Univ. of New Mexico, Albuquerque, NM (United States). Dept. of Chemical and Nuclear Engineering; Bullington, J.A. [AMMPEC, Inc., Albuquerque, NM (United States)

1998-04-01T23:59:59.000Z

79

Video and thermal imaging system for monitoring interiors of high temperature reaction vessels  

Science Conference Proceedings (OSTI)

A system and method for real-time monitoring of the interior of a combustor or gasifier wherein light emitted by the interior surface of a refractory wall of the combustor or gasifier is collected using an imaging fiber optic bundle having a light receiving end and a light output end. Color information in the light is captured with primary color (RGB) filters or complimentary color (GMCY) filters placed over individual pixels of color sensors disposed within a digital color camera in a BAYER mosaic layout, producing RGB signal outputs or GMCY signal outputs. The signal outputs are processed using intensity ratios of the primary color filters or the complimentary color filters, producing video images and/or thermal images of the interior of the combustor or gasifier.

Saveliev, Alexei V. (Chicago, IL); Zelepouga, Serguei A. (Hoffman Estates, IL); Rue, David M. (Chicago, IL)

2012-01-10T23:59:59.000Z

80

In-scene atmospheric correction of hyperspectral thermal infrared images with nadir, horizontal, and oblique view angles  

Science Conference Proceedings (OSTI)

Atmospheric corrections for hyperspectral thermal images acquired with nadir, horizontal, and oblique views have typically relied on atmospheric modelling software, such as Moderate Resolution Atmospheric Transmission MODTRAN, to estimate atmospheric ...

MattR. Smith; AlanR. Gillespie; Hugau Mizzon; LeeK. Balick; Juan Carlos Jimnez-Muoz; JoseA. Sobrino

2013-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "imaging multispectral thermal" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Underwater Radiance Distributions Measured with Miniaturized Multispectral Radiance Cameras  

Science Conference Proceedings (OSTI)

Miniaturized radiance cameras measuring underwater multispectral radiances in all directions at high-radiometric accuracy (CE600) are presented. The camera design is described, as well as the main steps of its optical and radiometric ...

David Antoine; Andr Morel; Edouard Leymarie; Amel Houyou; Bernard Gentili; Stphane Victori; Jean-Pierre Buis; Nicolas Buis; Sylvain Meunier; Marius Canini; Didier Crozel; Bertrand Fougnie; Patrice Henry

2013-01-01T23:59:59.000Z

82

A Method for Multisensor-Multispectral Satellite Data Fusion  

Science Conference Proceedings (OSTI)

Multisensor-multispectral scientific data applications require a tremendous investment regarding data preparation and analysis. A data fusion method is developed that is general enough for use with any scan-line-based datasets (satellite and ...

Andrew S. Jones; Kenneth E. Eis; Thomas H. Vonder Haar

1995-08-01T23:59:59.000Z

83

Imaging Fluid Flow in Geothermal Wells Using Distributed Thermal Perturbation Sensing  

E-Print Network (OSTI)

and end of the cooling periods for both thermal perturbationduring cooling period are used for estimation of thermal andduring cooling period are used for estimation of thermal and

Freifeld, B.

2011-01-01T23:59:59.000Z

84

Optimizing Digital Hardware Perceptrons for Multi-Spectral Image Classification.  

E-Print Network (OSTI)

Nonproliferation and International Security Division, Los Alamos National Laboratory, New Mexico. Abstract. We

Theiler, James

85

Retrieval of Cloud Microphysical Properties from Thermal Infrared Observations by a Fast Iterative Radiance Fitting Method  

Science Conference Proceedings (OSTI)

An algorithm is presented for inferring the IR optical depth, effective radius, and liquid water path of clouds from multispectral observations of emitted thermal radiation, which takes advantage of the larger number of spectral channels of ...

C. Rathke; J. Fischer

2000-11-01T23:59:59.000Z

86

Automated Thermal Image Processing for Detection and Classification of Birds and Bats - FY2012 Annual Report  

DOE Green Energy (OSTI)

Surveying wildlife at risk from offshore wind energy development is difficult and expensive. Infrared video can be used to record birds and bats that pass through the camera view, but it is also time consuming and expensive to review video and determine what was recorded. We proposed to conduct algorithm and software development to identify and to differentiate thermally detected targets of interest that would allow automated processing of thermal image data to enumerate birds, bats, and insects. During FY2012 we developed computer code within MATLAB to identify objects recorded in video and extract attribute information that describes the objects recorded. We tested the efficiency of track identification using observer-based counts of tracks within segments of sample video. We examined object attributes, modeled the effects of random variability on attributes, and produced data smoothing techniques to limit random variation within attribute data. We also began drafting and testing methodology to identify objects recorded on video. We also recorded approximately 10 hours of infrared video of various marine birds, passerine birds, and bats near the Pacific Northwest National Laboratory (PNNL) Marine Sciences Laboratory (MSL) at Sequim, Washington. A total of 6 hours of bird video was captured overlooking Sequim Bay over a series of weeks. An additional 2 hours of video of birds was also captured during two weeks overlooking Dungeness Bay within the Strait of Juan de Fuca. Bats and passerine birds (swallows) were also recorded at dusk on the MSL campus during nine evenings. An observer noted the identity of objects viewed through the camera concurrently with recording. These video files will provide the information necessary to produce and test software developed during FY2013. The annotation will also form the basis for creation of a method to reliably identify recorded objects.

Duberstein, Corey A.; Matzner, Shari; Cullinan, Valerie I.; Virden, Daniel J.; Myers, Joshua R.; Maxwell, Adam R.

2012-09-01T23:59:59.000Z

87

A survey of current issues in inverse problem theory as applied to thermal wave imaging  

Science Conference Proceedings (OSTI)

The recovery of optical and thermal property depth profiles using thermal waves relies directly on the application of inverse problem theory to the photothermal data. A general strategy for assessing and interrelating existing works in the field is presented.

J. F. Power

1999-01-01T23:59:59.000Z

88

Classification of Multispectral High-Resolution Satellite Imagery Using LIDAR Elevation Data  

Science Conference Proceedings (OSTI)

This paper studies the influence of airborne LIDAR elevation data on the classification of multispectral SPOT5 imagery over a semi-urban area; to do this, multispectral and LIDAR elevation data are integrated in a single imagery file composed of independent ... Keywords: Classification, LIDAR, Satellite Imagery, Support Vector Machine

Mara C. Alonso; Jos A. Malpica

2008-12-01T23:59:59.000Z

89

Thermal imaging measurement of lateral diffusivity and non-invasive material defect detection  

DOE Patents (OSTI)

A system and method for determining lateral thermal diffusivity of a material sample using a heat pulse; a sample oriented within an orthogonal coordinate system; an infrared camera; and a computer that has a digital frame grabber, and data acquisition and processing software. The mathematical model used within the data processing software is capable of determining the lateral thermal diffusivity of a sample of finite boundaries. The system and method may also be used as a nondestructive method for detecting and locating cracks within the material sample.

Sun, Jiangang (Westmont, IL); Deemer, Chris (Downers Grove, IL)

2003-01-01T23:59:59.000Z

90

High Spatial Resolution Thermal Imaging of Multiple Section Semiconductor Lasers Ali Shakouri*  

E-Print Network (OSTI)

the thermal design of the device, we have achieved record level of damage free power dissipation in electro-absorption that could be used to control temperature of individual devices on a chip. They have achieved cooling power structures and integrated electro- absorption modulators. Integrated electroabsorption modulator is very

91

Digital image analysis to enhance underwritten text in the Archimedes palimpsest  

Science Conference Proceedings (OSTI)

This paper reports some of the results obtained by applying statistical processing techniques to multispectral images of the Archimedes palimpsest. We focused on the possibilities of extracting the faint and highly degraded underwritten text, which constitutes ...

Emanuele Salerno; Anna Tonazzini; Luigi Bedini

2007-04-01T23:59:59.000Z

92

Pansharpening of high and medium resolution satellite images using bilateral filtering  

Science Conference Proceedings (OSTI)

We provide and evaluate a fusion algorithm of remotely sensed images, i.e. the fusion of a panchromatic (PAN) image with a multi-spectral (MS) image using bilateral filtering, applied to images of three different sensors: SPOT 5, Landsat ETM+ and Quickbird. ... Keywords: bilateral filter, image fusion, pansharpening

Diego Renza; Estibaliz Martinez; Agueda Arquero; Javier Sanchez

2010-11-01T23:59:59.000Z

93

Nanometric Optical Imaging Frontiers in Chemical Imaging  

E-Print Network (OSTI)

Nanometric Optical Imaging Frontiers in Chemical Imaging Seminar Series Presented by... Professor thermal imaging, chemical delivery and other new horizons. Finally, as part of this lecture, Lewis

94

Fusing multiple image transformations and a thermal sensor with kinect to improve person detection ability  

Science Conference Proceedings (OSTI)

This paper proposes a novel approach to combine data from multiple low-cost sensors to detect people in a mobile robot. Robust detection of people is a key capability required for robots working in environments with people. Several works have shown the ... Keywords: Computer vision, Data fusion, Image transformations, Machine learning

L. Susperregi, A. Arruti, E. Jauregi, B. Sierra, J. M. MartNez-Otzeta, E. Lazkano, A. Ansuategui

2013-09-01T23:59:59.000Z

95

An Artificial Neural Network Approach to Multispectral Rainfall Estimation over Africa  

Science Conference Proceedings (OSTI)

Multispectral Spinning Enhanced Visible and IR Interferometer (SEVIRI) data, calibrated with daily rain gauge estimates, were used to produce daily high-resolution rainfall estimates over Africa. An artificial neural network (ANN) approach was ...

Robin Chadwick; David Grimes

2012-06-01T23:59:59.000Z

96

Advances in the Detection and Analysis of Fog at Night Using GOES Multispectral Infrared Imagery  

Science Conference Proceedings (OSTI)

A technique is described for the detection of fog and low clouds at night using multispectral infrared (IR) imagery from Geostationary Operational Environmental Satellites (GOES). The technique requires subtraction and enhancement of digital data ...

Gary P. Ellrod

1995-09-01T23:59:59.000Z

97

Concept design, analysis, and integration of the new u.p.c. multispectral lidar system.  

E-Print Network (OSTI)

??The increasing need for range-resolved aerosol and water-vapour atmospheric observation networks worldwide has given rise to multi-spectral LIDARs (Light Detection and Ranging, a synonym of (more)

Kumar, Dhiraj

2012-01-01T23:59:59.000Z

98

Wavelength-Shifting-Fiber Scintillation Detectors for Thermal Neutron Imaging at SNS  

Science Conference Proceedings (OSTI)

We have developed wavelength-Shifting-fiber Scintillator Detector (SSD) with 0.3 m2 area per module. Each module has 154 x 7 pixels and a 5 mm x 50 mm pixel size. Our goal is to design a large area neutron detector offering higher detection efficiency and higher count-rate capability for Time-Of-Flight (TOF) neutron diffraction in Spallation Neutron Source (SNS). A ZnS/6LiF scintillator combined with a novel fiber encoding scheme was used to record the neutron events. A channel read-out-card (CROC) based digital-signal processing electronics and position-determination algorithm was applied for neutron imaging. Neutron-gamma discrimination was carried out using pulse-shape discrimination (PSD). A sandwich flat-scintillator detector can have detection efficiency close to He-3 tubes (about 10 atm). A single layer flat-scintillator detector has count rate capability of 6,500 cps/cm2, which is acceptable for powder diffractometers at SNS.

Clonts, Lloyd G [ORNL; Cooper, Ronald G [ORNL; Crow, Lowell [ORNL; Diawara, Yacouba [ORNL; Ellis, E Darren [ORNL; Funk, Loren L [ORNL; Hannan, Bruce W [ORNL; Hodges, Jason P [ORNL; Richards, John D [ORNL; Riedel, Richard A [ORNL; Wang, Cai-Lin [ORNL

2012-01-01T23:59:59.000Z

99

Remote sensing image segmentation by active queries Devis Tuia a,n  

E-Print Network (OSTI)

Remote sensing image segmentation by active queries Devis Tuia a,n , Jordi Mun~oz-Mari´ b , Gustavo Multiscale image segmentation Remote sensing Hyperspectral imagery Multispectral imagery a b s t r a c- istics in a compact way. For remote sensing image segmentation, the selected samples are the most

Camps-Valls, Gustavo

100

Mapping surface fuels using LIDAR and multispectral data fusion for fire behavior modeling  

E-Print Network (OSTI)

Fires have become intense and more frequent in the United States. Improving the accuracy of mapping fuel models is essential for fuel management decisions and explicit fire behavior prediction for real-time support of suppression tactics and logistics decisions. This study has two main objectives. The first objective is to develop the use of LIght Detection and Ranging (LIDAR) remote sensing to assess fuel models in East Texas accurately and effectively. More specific goals include: (1) developing LIDAR derived products and the methodology to use them for assessing fuel models; (2) investigating the use of several techniques for data fusion of LIDAR and multispectral imagery for assessing fuel models; (3) investigating the gain in fuels mapping accuracy with LIDAR as opposed to QuickBird imagery alone; and, (4) producing spatially explicit digital fuel maps. The second objective is to model fire behavior using FARSITE (Fire Area Simulator) and to investigate differences in modeling outputs using fuel model maps, which differ in accuracy, in east Texas. Estimates of fuel models were compared with in situ data collected over 62 plots. Supervised image classification methods provided better accuracy (90.10%) with the fusion of airborne LIDAR data and QuickBird data than with QuickBird imagery alone (76.52%). These two fuel model maps obtained from the first objective were used to see the differences in fire growth with fuel model maps of different accuracies. According to our results, LIDAR derived data provides accurate estimates of surface fuel parameters efficiently and accurately over extensive areas of forests. This study demonstrates the importance of using accurate maps of fuel models derived using new LIDAR remote sensing techniques.

Mutlu, Muge

2006-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "imaging multispectral thermal" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Imaging  

NLE Websites -- All DOE Office Websites (Extended Search)

Imaging Print Imaging Print The wavelengths of soft x-ray photons (1-15 nm) are very well matched to the creation of "nanoscopes" capable of probing the interior structure of biological cells and inorganic mesoscopic systems.Topics addressed by soft x-ray imaging techniques include cell biology, nanomagnetism, environmental science, and polymers. The tunability of synchrotron radiation is absolutely essential for the creation of contrast mechanisms. Cell biology CAT scans are performed in the "water window" (300-500 eV). Nanomagnetism studies require the energy range characteristic of iron, cobalt, and nickel (600-900 eV). Mid- and far-infrared (energies below 1 eV) microprobes using synchrotron radiation are being used to address problems such as chemistry in biological tissues, chemical identification and molecular conformation, environmental biodegradation, mineral phases in geological and astronomical specimens, and electronic properties of novel materials. Infrared synchrotron radiation is focused through, or reflected from, a small spot on the specimen and then analyzed using a spectrometer. Tuning to characteristic vibrational frequencies serves as a sensitive fingerprint for molecular species. Images of the various species are built up by raster scanning the specimen through the small illuminated spot.

102

Assessment of MTI Water Temperature Thermal Discharge Retrievals with Ground Truth  

Science Conference Proceedings (OSTI)

Surface water temperatures calculated from Multispectral Thermal Imager (MTI) brightness temperatures and the robust retrieval algorithm, developed by the Los Alamos National Laboratory (LANL), are compared with ground truth measurements at a mid-latitude cold-water site along the Atlantic coast near Plymouth, MA. In contrast to the relative uniformity of the sea-surface temperature in the open ocean the water temperature near Pilgrim exhibits strong spatial gradients and temporal variability. This made it critical that all images be accurately registered in order to extract temperature values at the six buoy locations. Sixteen images during a one-year period from August 2000 to July 2001 were selected for the study. The RMS error of Pilgrim water temperature is about 3.5 C for the 4 buoys located in open water. The RMS error of the combined temperatures from 3 of the open-water buoys is 2.8 C. The RMS error includes errors in the ground truth. The magnitude of this error is estimated to range between 0.8 and 2.3 C. The two main components of this error are warm-layer effect and spatial variability. The actual error in the MTI retrievals for Pilgrim daytime conditions is estimated to be between 2.7 and 3.4 C for individual buoys and between 1.7 and 2.7 C for the combined open-water buoys.

Kurzeja, R.J.

2002-12-06T23:59:59.000Z

103

Depth profiling the optical absorption and thermal reflection coefficient via an analysis based on the method of images (abstract)  

Science Conference Proceedings (OSTI)

The problem of depth profiling optical absorption in a thermally depth variable solid is a problem of direct interest for the analysis of complex structured materials. In this work

J. F. Power

2003-01-01T23:59:59.000Z

104

Earth resistivity estimation based on satellite imaging techniques  

Science Conference Proceedings (OSTI)

This paper proposes a useful technique for generating an earth resistivity map. Earth resistance is one of essential factors in a broad range of power system analysis and design. Information of earth resistivity is helpful for practical power system ... Keywords: Wenner method, classification technique, earth resistivity, multispectral, power system grounding, satellite image technology

Kwanchai Norsangsri; Thanatchai Kulworawanichpong

2009-09-01T23:59:59.000Z

105

A Method to Derive the Multispectral Surface Albedo Consistent with MODIS from Historical AVHRR and VGT Satellite Data  

Science Conference Proceedings (OSTI)

Multispectral surface albedo and bidirectional properties are required for accurate determination of the surface and atmosphere solar radiation budget. A method is developed here to obtain time series of these surface characteristics consistent ...

Alexander P. Trishchenko; Yi Luo; Konstantin V. Khlopenkov; Shusen Wang

2008-04-01T23:59:59.000Z

106

ARM XDC Datastreams  

NLE Websites -- All DOE Office Websites (Extended Search)

StreamsMultispectral Thermal Imager Documentation MTI Instrument MTI netCDF File Header Descriptions (Data Object Design Files) External Datastream Descriptions Order Data...

107

Definition: Hyperspectral Imaging | Open Energy Information  

Open Energy Info (EERE)

Imaging Imaging Jump to: navigation, search Dictionary.png Hyperspectral Imaging Hyperspectral sensors collect data across a wide range of the spectrum (VNIR-LWIR, plus TIR) at small spectral resolution (5-15 nm) and high spatial resolution (1-5 m). This allows detailed spectral signatures to be identified for different imaged materials - for example hyperspectral imaging can be used to identify specific clay minerals; multispectral imaging can identify only the presence of clay minerals in general. View on Wikipedia Wikipedia Definition Hyperspectral imaging, like other spectral imaging, collects and processes information from across the electromagnetic spectrum. Much as the human eye sees visible light in three bands (red, green, and blue), spectral imaging divides the spectrum into many more bands. This technique

108

A contiguity-enhanced k-means clustering algorithm for unsupervised multispectral image segmentation  

E-Print Network (OSTI)

Nonproliferation and International Security Division, MS-D436 Los Alamos National Laboratory, Los Alamos, NM 87545

Theiler, James

109

Thermal Scout Software - Energy Innovation Portal  

Energy Analysis Thermal ... Technology Marketing Summary. ... The software uses GPS data to automate infrared camera image capture and temperature ana ...

110

Bayesian inference for multiband image segmentation via model-based cluster trees  

Science Conference Proceedings (OSTI)

We consider the problem of multiband image clustering and segmentation. We propose a new methodology for doing this, called model-based cluster trees. This is grounded in model-based clustering, which bases inference on finite mixture models estimated ... Keywords: Bayesian model, Clustering, Hyperspectral, Information criterion, Information fusion, Ising, Markov model, Multiband, Multichannel, Multispectral, Potts, Quantization, Segmentation

Fionn Murtagh; Adrian E. Raftery; Jean-Luc Starck

2005-06-01T23:59:59.000Z

111

Algorithms using inter-band cross-correlation for pixel registration and jitter reconstruction in multi-channel push-broom imagers  

SciTech Connect

We present two algorithms for determining sensor motion of a multi-spectral push-broom imager for use in subsequent image registration. The first algorithm, termed the {open_quotes}pairwise{close_quotes} method, performs cross-correlations between individual pairs of channels. The offsets of maximum correlation are formulated into a system of linear equations whose solution gives an estimate of the jitter function. The second algorithm performs cross-correlations between channels and a reference image called the {open_quotes}baseline{close_quotes} which is constructed by averaging together all the channels in the image cube. An estimated jitter time series is computed for each channel, all of which are overlapped and averaged to obtain a best estimate of the jitter function. The pairwise method is more general in that it can handle a wider range of jitter scenarios. The baseline method, although more restricted, is very simple to implement, and its accuracy can be improved substantially through iteration. In this paper, we describe both methods in detail and present results of simulations performed on thermal-infrared data cubes.

Theiler, J.; Henderson, B.G.; Smith, B.W.

1997-11-01T23:59:59.000Z

112

Derivation of Seasonal Cloud Properties at ARM-NSA from Multispectral MODIS Data  

NLE Websites -- All DOE Office Websites (Extended Search)

Derivation of Seasonal Cloud Properties at ARM-NSA Derivation of Seasonal Cloud Properties at ARM-NSA from Multispectral MODIS Data D. A. Spangenberg Analytical Services and Materials, Inc. Hampton, Virginia P. Minnis National Aeronautics and Space Administration Langley Research Center Hampton, Virginia T. Uttal National Oceanic and Atmospheric Administration Environmental Technology Laboratory Boulder, Colorado Q. Z. Trepte and S. S.-Mack Science Applications International Corporation Hampton, Virginia Introduction Improving climate model predictions over earth's Polar Regions requires a complete knowledge of polar cloud microphysics. Over the Arctic, there is minimal contrast between the clouds and background snow surface observed in satellite data, especially for visible wavelengths. This makes it difficult to

113

Instrillment Development Multi-Spectral Automated Rotating Shadowt)and Radiometry  

NLE Websites -- All DOE Office Websites (Extended Search)

Instrillment Development Instrillment Development Multi-Spectral Automated Rotating Shadowt)and Radiometry L. Harrison Atmospheric: Sciences Research Center State University of New York at Albany Albany, NY 12205 I am developing two related instruments for use in the Atmospheric Radiation Measurement (ARM) p,rogram; both use an automated rotating shadowband technique to make spectrally resolved measurements of the direct-normal, total horizontal, and diffuse horizontal irradiances. These parameters of the sky-radiance function are measured using the same detector (for a given wavelength), eliminating the difficulties inherent in comparing these data when measured by independent detectors. The first of these instruments uses independent interterence-filter/photodiode detectors to measure any seven

114

Practical Atmospheric Correction Algorithms for a Multi-Spectral Sensor From the Visible Through the Thermal Spectral Regions  

Science Conference Proceedings (OSTI)

Deriving information about the Earth's surface requires atmospheric corrections of the measured top-of-the-atmosphere radiances. One possible path is to use atmospheric radiative transfer codes to predict how the radiance leaving the ground is affected by the scattering and attenuation. In practice the atmosphere is usually not well known and thus it is necessary to use more practical methods. The authors will describe how to find dark surfaces, estimate the atmospheric optical depth, estimate path radiance and identify thick clouds using thresholds on reflectance and NDVI and columnar water vapor. The authors describe a simple method to correct a visible channel contaminated by a thin cirrus clouds.

Borel, C.C.; Villeneuve, P.V.; Clodium, W.B.; Szymenski, J.J.; Davis, A.B.

1999-04-04T23:59:59.000Z

115

aster-biblio.enl Page 1 Abbott, E. A. Proceedings of the Third Thermal Infrared Multispectral Scanner (TIMS)  

E-Print Network (OSTI)

by any electronic or mechanical means (including photocopying, recording, or information storage.8.3 Downhole pumps _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _5-9 5.8.4 High expansion of U.S. hydropower potential using existing dams and impoundments. But outside of a few pumped

116

Full field imaging based instantaneous hyperspectral absolute refractive index measurement  

SciTech Connect

Multispectral refractometers typically measure refractive index (RI) at discrete monochromatic wavelengths via a serial process. We report on the demonstration of a white light full field imaging based refractometer capable of instantaneous multispectral measurement of absolute RI of clear liquid/gel samples across the entire visible light spectrum. The broad optical bandwidth refractometer is capable of hyperspectral measurement of RI in the range 1.30 1.70 between 400nm 700nm with a maximum error of 0.0036 units (0.24% of actual) at 414nm for a = 1.50 sample. We present system design and calibration method details as well as results from a system validation sample.

Baba, Justin S [ORNL; Boudreaux, Philip R [ORNL

2012-01-01T23:59:59.000Z

117

THERMAL RECOVERY  

NLE Websites -- All DOE Office Websites (Extended Search)

THERMAL RECOVERY Thermal recovery comprises the techniques of steamflooding, cyclic steam stimulation, and in situ combustion. In steamflooding, high-temperature steam is injected...

118

University of Colorado Thermal Comfort Report  

NLE Websites -- All DOE Office Websites (Extended Search)

A A Warmboard sub-floor with tubing and wood Image Courtsey of Warmboard Image Thermal Comfort "That Condition of mind, which expresses satisfaction with the thermal environment" (ASHRAE Standard 55) Design Criteria Design Criteria Design Criteria Design Criteria 1. Thermally comfortable conditions achieved by integrating technologically and economically innovative, low-energy strategies: a. Temperatures between 72 o F and 76 o F b. Humidity between 40.0% and 55.0% 2. Minimal distractions to the occupant 3. Easy control of thermal comfort system 4. Uniform thermal conditions exist throughout the house Bio Bio Bio Bio- - - -S S S S ( ( ( (h h h h) ) ) ) ip ip ip ip Thermal Comfort Features Thermal Comfort Features Thermal Comfort Features Thermal Comfort Features

119

Capturing the Green River -- Multispectral airborne videography to evaluate the environmental impacts of hydropower operations  

DOE Green Energy (OSTI)

The 500-mile long Green River is the largest tributary of the Colorado River. From its origin in the Wind River Range mountains of western Wyoming to its confluence with the Colorado River in southeastern Utah, the Green River is vital to the arid region through which it flows. Large portions of the area remain near-wilderness with the river providing a source of recreation in the form of fishing and rafting, irrigation for farming and ranching, and hydroelectric power. In the late 1950`s and early 1960`s hydroelectric facilities were built on the river. One of these, Flaming Gorge Dam, is located just south of the Utah-Wyoming border near the town of Dutch John, Utah. Hydropower operations result in hourly and daily fluctuations in the releases of water from the dam that alter the natural stream flow below the dam and affect natural resources in and along the river corridor. In the present study, the authors were interested in evaluating the potential impacts of hydropower operations at Flaming Gorge Dam on the downstream natural resources. Considering the size of the area affected by the daily pattern of water release at the dam as well as the difficult terrain and limited accessibility of many reaches of the river, evaluating these impacts using standard field study methods was virtually impossible. Instead an approach was developed that used multispectral aerial videography to determine changes in the affected parameters at different flows, hydrologic modeling to predict flow conditions for various hydropower operating scenarios, and ecological information on the biological resources of concern to assign impacts.

Snider, M.A.; Hayse, J.W.; Hlohowskyj, I.; LaGory, K.E.

1996-02-01T23:59:59.000Z

120

Assessing Available Woody Plant Biomass on Rangelands with Lidar and Multispectral Remote Sensing  

E-Print Network (OSTI)

The majority of biofuels are produced from corn and grain. The drawback to these sources of biofuels is the vast amount of cultivated land needed to produce substantial amounts of biofuel, potentially increasing the price of food and livestock products. Mesquite trees, a type of woody plant, are a proven source of bioenergy feedstock found on semi-arid lands. The overall objectives of this study were to develop algorithms for determining woody plant biomass on rangelands in Texas at plot-level using terrestrial lidar and at the local scale by integrating reference biomass and multispectral imagery. Terrestrial lidar offers a more efficient method for estimating biomass than traditional field measurements. Variables from the terrestrial lidar point cloud were compared to ground measurements of biomass to find a best fitting regression model. Two processing methods were investigated for analyzing the lidar point cloud data, namely: 1) percentile height statistics and 2) a height bin approach. Regression models were developed for variables obtained through each processing technique for estimating woody plant, above-ground biomass. Regression models were able to explain 81 percent and 77 percent of the variance associated with the aboveground biomass using percentile height statistics and height bins, respectively. The aboveground biomass map was generated by using the cokriging interpolation method with NDVI and ground biomass data. According to cross-validation, ordinary cokriging estimated biomass accurately (R^2 = 0.99). The results of this study revealed that terrestrial lidar can be used to accurately and efficiently estimate the aboveground biomass of mesquite trees in a semi-arid environment at plot level. Moreover, spatial interpolation techniques proved useful in scaling up biomass estimates to local scale.

Ku, Nian-Wei

2011-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "imaging multispectral thermal" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Underhood Thermal Management [Heat Transfer and Fluid Mechanics] - Nuclear  

NLE Websites -- All DOE Office Websites (Extended Search)

Underhood Thermal Underhood Thermal Management Capabilities Engineering Computation and Design Engineering and Structural Mechanics Systems/Component Design, Engineering and Drafting Heat Transfer and Fluid Mechanics Overview Thermal Hydraulic Optimization of Nuclear Systems Underhood Thermal Management Combustion Simulations Advanced Model and Methodology Development Multi-physics Reactor Performance and Safety Simulations Other Capabilities Work with Argonne Contact us For Employees Site Map Help Join us on Facebook Follow us on Twitter NE on Flickr Heat Transfer and Fluid Mechanics Bookmark and Share Underhood Thermal Management Hybrid Vehicle Underhood Thermal Analysis Hybrid Vehicle Underhood Thermal Analysis. Click on image to view larger image. In addition to nuclear system applications, the section applies its

122

NIST Image Gallery: Image Details  

Science Conference Proceedings (OSTI)

... Image Gallery : Image Details. 72 DPI Image 150 DPI Image No 300 DPI Version. Title: Frequency Comb, Ultrafast Laser. ...

123

NIST Image Gallery: Image Details  

Science Conference Proceedings (OSTI)

... Image Gallery : Image Details. 72 DPI Image 150 DPI Image No 300 DPI Version. Title: Iron-Based Superconductors. Description ...

124

NIST Image Gallery: Image Details  

Science Conference Proceedings (OSTI)

... Image Gallery : Image Details. 72 DPI Image 150 DPI Image No 300 DPI Version. Title: Space Weather Forecasts. Description ...

125

NIST Image Gallery: Image Details  

Science Conference Proceedings (OSTI)

... Image Gallery : Image Details. 72 DPI Image 150 DPI Image No 300 DPI Version. Title: Organic Solar Power. Description ...

126

NIST Image Gallery: Image Details  

Science Conference Proceedings (OSTI)

... 72 DPI Image 150 DPI Image 300 DPI Image . Title: Nanotechnology; Biotechnology/Health; Nanocrystals; Hwang. ...

127

Airborne Scanning Spectrometer for Remote Sensing of Cloud, Aerosol, Water Vapor, and Surface Properties  

Science Conference Proceedings (OSTI)

An airborne scanning spectrometer was developed for measuring reflected solar and emitted thermal radiation in 50 narrowband channels between 0.55 and 14.2 m. The instrument provides multispectral images of outgoing radiation for purposes of ...

Michael D. King; W. Paul Menzel; Patrick S. Grant; Jeffrey S. Myers; G. Thomas Arnold; Steven E. Platnick; Liam E. Gumley; Si-Chee Tsay; Christopher C. Moeller; Michael Fitzgerald; Kenneth S. Brown; Fred G. Osterwisch

1996-08-01T23:59:59.000Z

128

Satellite Microphysical Retrievals for Land-Based Fog with Validation by Balloon Profiling  

Science Conference Proceedings (OSTI)

Digital data from the National Oceanic and Atmospheric Administration Advanced very High Resolution Radiometer (AVHRR) satellite instrument provides multispectral images in visible near-infrared and thermal infrared wave bands, which have been ...

Melanie A. Wetzel; Randolph D. Borys; Ling E. Xu

1996-06-01T23:59:59.000Z

129

Preflight and In-Flight Calibration Plan for ASTER  

Science Conference Proceedings (OSTI)

Preflight and in-flight radiometric calibration plans are described for the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) that is a multispectral optical imager of high spatial resolution. It is designed for the remote ...

A. Ono; F. Sakuma; K. Arai; Y. Yamaguchi; H. Fujisada; P. N. Slater; K. J. Thome; F. D. Palluconi; H. H. Kieffer

1996-04-01T23:59:59.000Z

130

Filtering, Sampling, and Information Content within Satellite-Derived Multispectral or Mixed-Resolution Imagery  

Science Conference Proceedings (OSTI)

The importance of an alias-free imaging approach to multidimensional sounder instrumentation is highlighted, together with its potential for improving noise-equivalent differential temperature and spatial resolution over current designs. ...

A. C. L. Lee

1994-04-01T23:59:59.000Z

131

High-Spatial-Resolution Surface and Cloud-Type Classification from MODIS Multispectral Band Measurements  

Science Conference Proceedings (OSTI)

A method for automated classification of surface and cloud types using Moderate Resolution Imaging Spectroradiometer (MODIS) radiance measurements has been developed. The MODIS cloud mask is used to define the training sets. Surface and cloud-...

Jun Li; W. Paul Menzel; Zhongdong Yang; Richard A. Frey; Steven A. Ackerman

2003-02-01T23:59:59.000Z

132

High resolution, low cost, privacy preserving human motion tracking system via passive thermal sensing  

E-Print Network (OSTI)

Thermal imaging is powerful but expensive. This thesis presents an alternative thermal sensing system capable of tracking human motion by using a novel projection mechanism from an array of inexpensive single-bit thermal ...

Browarek, Sharmeen

2010-01-01T23:59:59.000Z

133

Full Size Image - Energy Innovation Portal  

Share Full Size Image - Energy Innovation Portal on Facebook; ... Hydropower, Wave and Tidal; Industrial Technologies; Solar Photovoltaic; Solar Thermal; Startup America;

134

Thermally-induced voltage alteration for analysis of ...  

... an image can be generated directly from a thermoelectric potential produced by localized laser heating at the ... Building Energy ... Solar Thermal;

135

Spectral Imaging II: Plant disease detection based on data fusion of hyper-spectral and multi-spectral fluorescence imaging using Kohonen maps  

Science Conference Proceedings (OSTI)

The objective of this research was to develop a ground-based real-time remote sensing system for detecting diseases in arable crops under field conditions and in an early stage of disease development, before it can visibly be detected. This was achieved ...

D. Moshou; C. Bravo; R. Oberti; J. West; L. Bodria; A. McCartney; H. Ramon

2005-04-01T23:59:59.000Z

136

Quantitative luminescence imaging system  

DOE Patents (OSTI)

The QLIS images and quantifies low-level chemiluminescent reactions in an electromagnetic field. It is capable of real time nonperturbing measurement and simultaneous recording of many biochemical and chemical reactions such as luminescent immunoassays or enzyme assays. The system comprises image transfer optics, a low-light level digitizing camera with image intensifying microchannel plates, an image process or, and a control computer. The image transfer optics may be a fiber image guide with a bend, or a microscope, to take the light outside of the RF field. Output of the camera is transformed into a localized rate of cumulative digitalized data or enhanced video display or hard-copy images. The system may be used as a luminescent microdosimetry device for radiofrequency or microwave radiation, as a thermal dosimeter, or in the dosimetry of ultra-sound (sonoluminescence) or ionizing radiation. It provides a near-real-time system capable of measuring the extremely low light levels from luminescent reactions in electromagnetic fields in the areas of chemiluminescence assays and thermal microdosimetry, and is capable of near-real-time imaging of the sample to allow spatial distribution analysis of the reaction. It can be used to instrument three distinctly different irradiation configurations, comprising (1) RF waveguide irradiation of a small Petri-dish-shaped sample cell, (2) RF irradiation of samples in a microscope for the microscopic imaging and measurement, and (3) RF irradiation of small to human body-sized samples in an anechoic chamber. 22 figs.

Erwin, D.N.; Kiel, J.L.; Batishko, C.R.; Stahl, K.A.

1990-08-14T23:59:59.000Z

137

Quantitative luminescence imaging system  

DOE Patents (OSTI)

The QLIS images and quantifies low-level chemiluminescent reactions in an electromagnetic field. It is capable of real time nonperturbing measurement and simultaneous recording of many biochemical and chemical reactions such as luminescent immunoassays or enzyme assays. The system comprises image transfer optics, a low-light level digitizing camera with image intensifying microchannel plates, an image process or, and a control computer. The image transfer optics may be a fiber image guide with a bend, or a microscope, to take the light outside of the RF field. Output of the camera is transformed into a localized rate of cumulative digitalized data or enhanced video display or hard-copy images. The system may be used as a luminescent microdosimetry device for radiofrequency or microwave radiation, as a thermal dosimeter, or in the dosimetry of ultra-sound (sonoluminescence) or ionizing radiation. It provides a near-real-time system capable of measuring the extremely low light levels from luminescent reactions in electromagnetic fields in the areas of chemiluminescence assays and thermal microdosimetry, and is capable of near-real-time imaging of the sample to allow spatial distribution analysis of the reaction. It can be used to instrument three distinctly different irradiation configurations, comprising (1) RF waveguide irradiation of a small Petri-dish-shaped sample cell, (2) RF irradiation of samples in a microscope for the microscopie imaging and measurement, and (3) RF irradiation of small to human body-sized samples in an anechoic chamber.

Erwin, David N. (San Antonio, TX); Kiel, Johnathan L. (San Antonio, TX); Batishko, Charles R. (West Richland, WA); Stahl, Kurt A. (Richland, WA)

1990-01-01T23:59:59.000Z

138

NIST Image Gallery: Image Details  

Science Conference Proceedings (OSTI)

... 72 DPI Image 150 DPI Image 300 DPI Image . Title: Quantum Physics; Quantum Communications; Ultrafast Photon Detector; Nam. ...

139

NIST Image Gallery: Image Details  

Science Conference Proceedings (OSTI)

... 72 DPI Image 150 DPI Image 300 DPI Image . Title: Energy; Fossil Fuels;Distillation Curves for Complex Fuel Mixtures. ...

140

NIST Image Gallery: Image Details  

Science Conference Proceedings (OSTI)

... 72 DPI Image 150 DPI Image 300 DPI Image . Title: Scanning Electron Microscope with Spin Polarization Analysis. ...

Note: This page contains sample records for the topic "imaging multispectral thermal" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

NIST Image Gallery: Image Details  

Science Conference Proceedings (OSTI)

... 72 DPI Image 150 DPI Image 300 DPI Image . Title: Metrology, Basic Units; Mass; Electronic Kilogram. Description ...

142

NIST Image Gallery: Image Details  

Science Conference Proceedings (OSTI)

... nist.gov. 72 DPI Image 150 DPI Image 300 DPI Image . Title: Public safety & Smart Grid. Description: Electrical engineer ...

143

NIST Image Gallery: Image Details  

Science Conference Proceedings (OSTI)

... Image Gallery : Image Details. 72 DPI Image No 150 DPI Version 300 DPI Image. Title: Ultrafast Laser Speeds Up Quest for Atomic Control. ...

144

NIST Image Gallery: Image Details  

Science Conference Proceedings (OSTI)

... Image Gallery : Image Details. 72 DPI Image 150 DPI Image No 300 DPI Version. Title: House; Trees. Description: *BFRL. Subjects (names): ...

145

NIST Image Gallery: Image Details  

Science Conference Proceedings (OSTI)

... 72 DPI Image 150 DPI Image 300 DPI Image . Title: New Imaging Tool is Boon to Fuel Cell Research. Description: NIST ...

146

Thermal Properties  

Science Conference Proceedings (OSTI)

Table 12   Thermal conductivities of polymers and other materials...40,000 2.8 Aluminum 24,000 1.7 Steel 5000 0.35 Granite 350 0.02 Crown glass (75 wt% silica) 90 0.006 Source: Ref 4...

147

Evaluating fusion techniques for multi-sensor satellite image data  

SciTech Connect

Satellite image data fusion is a topic of interest in many areas including environmental monitoring, emergency response, and defense. Typically any single satellite sensor cannot provide all of the benefits offered by a combination of different sensors (e.g., high-spatial but low spectral resolution vs. low-spatial but high spectral, optical vs. SAR). Given the respective strengths and weaknesses of the different types of image data, it is beneficial to fuse many types of image data to extract as much information as possible from the data. Our work focuses on the fusion of multi-sensor image data into a unified representation that incorporates the potential strengths of a sensor in order to minimize classification error. Of particular interest is the fusion of optical and synthetic aperture radar (SAR) images into a single, multispectral image of the best possible spatial resolution. We explore various methods to optimally fuse these images and evaluate the quality of the image fusion by using K-means clustering to categorize regions in the fused images and comparing the accuracies of the resulting categorization maps.

Martin, Benjamin W [ORNL; Vatsavai, Raju [ORNL

2013-01-01T23:59:59.000Z

148

Ralph: A Visible/Infrared Imager for the New Horizons Pluto/Kuiper Belt Mission  

E-Print Network (OSTI)

The New Horizons instrument named Ralph is a visible/near infrared multi-spectral imager and a short wavelength infrared spectral imager. It is one of the core instruments on New Horizons, NASA's first mission to the Pluto/Charon system and the Kuiper Belt. Ralph combines panchromatic and color imaging capabilities with IR imaging spectroscopy. Its primary purpose is to map the surface geology and composition of these objects, but it will also be used for atmospheric studies and to map the surface temperature. It is a compact, low-mass (10.5 kg), power efficient (7.1 W peak), and robust instrument with good sensitivity and excellent imaging characteristics. Other than a door opened once in flight, it has no moving parts. These characteristics and its high degree of redundancy make Ralph ideally suited to this long-duration flyby reconnaissance mission.

Reuter, Dennis C; Scherrer, John; Jennings, Donald E; Baer, James; Hanley, John; Hardaway, Lisa; Lunsford, Allen; McMuldroch, Stuart; Moore, Jeffrey; Olkin, Cathy; Parizek, Robert; Reitsma, Harold; Sabatke, Derek; Spencer, John; Stone, John; Throop, Henry; Van Cleve, Jeffrey; Weigle, Gerald E; Young, Leslie A

2007-01-01T23:59:59.000Z

149

Ralph: A Visible/Infrared Imager for the New Horizons Pluto/Kuiper Belt Mission  

E-Print Network (OSTI)

The New Horizons instrument named Ralph is a visible/near infrared multi-spectral imager and a short wavelength infrared spectral imager. It is one of the core instruments on New Horizons, NASA's first mission to the Pluto/Charon system and the Kuiper Belt. Ralph combines panchromatic and color imaging capabilities with IR imaging spectroscopy. Its primary purpose is to map the surface geology and composition of these objects, but it will also be used for atmospheric studies and to map the surface temperature. It is a compact, low-mass (10.5 kg), power efficient (7.1 W peak), and robust instrument with good sensitivity and excellent imaging characteristics. Other than a door opened once in flight, it has no moving parts. These characteristics and its high degree of redundancy make Ralph ideally suited to this long-duration flyby reconnaissance mission.

Dennis C. Reuter; S. Alan Stern; John Scherrer; Donald E. Jennings; James Baer; John Hanley; Lisa Hardaway; Allen Lunsford; Stuart McMuldroch; Jeffrey Moore; Cathy Olkin; Robert Parizek; Harold Reitsma; Derek Sabatke; John Spencer; John Stone; Henry Throop; Jeffrey Van Cleve; Gerald E. Weigle; Leslie A. Young

2007-09-26T23:59:59.000Z

150

Evaluation of thermal remote sensing as a low-cost regional geothermal exploration technique in New Mexico. Final report  

DOE Green Energy (OSTI)

Airborne and satellite borne thermal infrared scanner data were analyzed for application in the exploration of geothermal resources in New Mexico. The location for this study was the East Mesa Geothermal Field near Las Cruces, New Mexico. Primary sensor was the Thermal Infrared Multispectral Scanner (TIMS) which obtained data at 10-meter resolution. Additional data for comparison came from the Heat Capacity Mapping Mission (HCMM) satellite which provided data at 600-meter resolution. These data were compared to the soils, vegetation, and geology of the area, as well as borehole temperature data in an attempt to explain temperature patterns and anomalies. Thermal infrared scanner data were found to be too sensitive to solar-induced temperature anomalies to directly reflect the presence of subsurface geothermal anomalies but may provide valuable supporting information for a geothermal exploration program. 15 refs., 16 figs., 3 tabs.

Inglis, M.; Budge, T.K.

1985-03-01T23:59:59.000Z

151

Aerosol Properties from Multi-spectral and Multi-angular Aircraft 4STAR Observations: Expected Advantages and Challenges  

SciTech Connect

The airborne Spectrometer for Sky-Scanning, Sun-Tracking Atmospheric Research (4STAR) is developed to retrieve aerosol microphysical and optical properties from multi-angular and multi-spectral measurements of sky radiance and direct-beam sun transmittance. The necessarily compact design of the 4STAR may cause noticeable apparent enhancement of sky radiance at small scattering angles. We assess the sensitivity of expected 4STAR-based aerosol retrieval to such enhancement by applying the operational AERONET retrieval code and constructed synthetic 4STARlike data. Also, we assess the sensitivity of the broadband fluxes and the direct aerosol radiative forcing to uncertainties in aerosol retrievals associated with the sky radiance enhancement. Our sensitivity study results suggest that the 4STARbased aerosol retrieval has limitations in obtaining detailed information on particle size distribution and scattering phase function. However, these limitations have small impact on the retrieved bulk optical parameters, such as the asymmetry factor (up to 4%, or 0.02) and single-scattering albedo (up to 2%, or 0.02), and the calculated direct aerosol radiative forcing (up to 6%, or 2 Wm-2).

Kassianov, Evgueni I.; Flynn, Connor J.; Redemann, Jens; Schmid, Beat; Russell, P. B.; Sinyuk, Alexander

2012-11-01T23:59:59.000Z

152

AQUIFER THERMAL ENERGY STORAGE  

E-Print Network (OSTI)

aquifers for thermal energy storage. Problems outlined aboveModeling of Thermal Energy Storage in Aquifers," Proceed-ings of Aquifer Thermal Energy Storage Workshop, Lawrence

Tsang, C.-F.

2011-01-01T23:59:59.000Z

153

AQUIFER THERMAL ENERGY STORAGE  

E-Print Network (OSTI)

using aquifers for thermal energy storage. Problems outlinedmatical Modeling of Thermal Energy Storage in Aquifers,"Proceed- ings of Aquifer Thermal Energy Storage Workshop,

Tsang, C.-F.

2011-01-01T23:59:59.000Z

154

NIST Image Gallery: Image Details  

Science Conference Proceedings (OSTI)

... 72 DPI Image 150 DPI Image 300 DPI Image . Title: Homeland Security; Chem., Bio, and Other Threats; Standards for Radiation Detection. ...

155

NIST Image Gallery: Image Details  

Science Conference Proceedings (OSTI)

... Image Gallery : Image Details. No 72 DPI Version No 150 DPI Version 300 DPI Image. Title: Gold Nano Anchors Put Nanowires in Their Place. ...

156

NIST Image Gallery: Image Details  

Science Conference Proceedings (OSTI)

... 72 DPI Image 150 DPI Image 300 DPI Image . Title: Iron-based and Copper-Oxide High-Temperature Superconductors. ...

157

Thermal conductivity of thermal-battery insulations  

DOE Green Energy (OSTI)

The thermal conductivities of a variety of insulating materials used in thermal batteries were measured in atmospheres of argon and helium using several techniques. (Helium was used to simulate the hydrogen atmosphere that results when a Li(Si)/FeS{sub 2} thermal battery ages.) The guarded-hot-plate method was used with the Min-K insulation because of its extremely low thermal conductivity. For comparison purposes, the thermal conductivity of the Min-K insulating board was also measured using the hot-probe method. The thermal-comparator method was used for the rigid Fiberfrax board and Fiberfrax paper. The thermal conductivity of the paper was measured under several levels of compression to simulate the conditions of the insulating wrap used on the stack in a thermal battery. The results of preliminary thermal-characterization tests with several silica aerogel materials are also presented.

Guidotti, R.A.; Moss, M.

1995-08-01T23:59:59.000Z

158

Speckle-free laser imaging  

E-Print Network (OSTI)

Many imaging applications require increasingly bright illumination sources, motivating the replacement of conventional thermal light sources with light emitting diodes (LEDs), superluminescent diodes (SLDs) and lasers. Despite their brightness, lasers and SLDs are poorly suited for full-field imaging applications because their high spatial coherence leads to coherent artifacts known as speckle that corrupt image formation. We recently demonstrated that random lasers can be engineered to provide low spatial coherence. Here, we exploit the low spatial coherence of specifically-designed random lasers to perform speckle-free full-field imaging in the setting of significant optical scattering. We quantitatively demonstrate that images generated with random laser illumination exhibit higher resolution than images generated with spatially coherent illumination. By providing intense laser illumination without the drawback of coherent artifacts, random lasers are well suited for a host of full-field imaging applicatio...

Redding, Brandon; Cao, Hui

2011-01-01T23:59:59.000Z

159

Seasonal thermal energy storage  

DOE Green Energy (OSTI)

This report describes the following: (1) the US Department of Energy Seasonal Thermal Energy Storage Program, (2) aquifer thermal energy storage technology, (3) alternative STES technology, (4) foreign studies in seasonal thermal energy storage, and (5) economic assessment.

Allen, R.D.; Kannberg, L.D.; Raymond, J.R.

1984-05-01T23:59:59.000Z

160

Principal Component Image Analysis of MODIS for Volcanic Ash. Part II: Simulation of Current GOES and GOES-M Imagers  

Science Conference Proceedings (OSTI)

In Part I of this paper the infrared bands of the Moderate Resolution Imaging Spectroradiometer (MODIS) were analyzed using principal component image analysis for volcanic ash signals. The analyses performed determined that several of the thermal ...

Donald W. Hillger; James D. Clark

2002-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "imaging multispectral thermal" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Thermal Hydraulic Optimization of Nuclear Systems [Heat Transfer and Fluid  

NLE Websites -- All DOE Office Websites (Extended Search)

Thermal Hydraulic Thermal Hydraulic Optimization of Nuclear Systems Capabilities Engineering Computation and Design Engineering and Structural Mechanics Systems/Component Design, Engineering and Drafting Heat Transfer and Fluid Mechanics Overview Thermal Hydraulic Optimization of Nuclear Systems Underhood Thermal Management Combustion Simulations Advanced Model and Methodology Development Multi-physics Reactor Performance and Safety Simulations Other Capabilities Work with Argonne Contact us For Employees Site Map Help Join us on Facebook Follow us on Twitter NE on Flickr Heat Transfer and Fluid Mechanics Bookmark and Share Thermal Hydraulic Optimization of Nuclear Systems Accelerator Driven Test Facility Target Accelerator Driven Test Facility Target. Click on image to view larger

162

Geothermal Exploration In Akutan, Alaska, Using Multitemporal Thermal  

Open Energy Info (EERE)

Akutan, Alaska, Using Multitemporal Thermal Akutan, Alaska, Using Multitemporal Thermal Infrared Images Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Conference Proceedings: Geothermal Exploration In Akutan, Alaska, Using Multitemporal Thermal Infrared Images Details Activities (1) Areas (1) Regions (0) Abstract: The Akutan geothermal system, which is a part of Alaska's Aleutian volcanic arc, has several known thermal springs and a known fumarole field. It is reported to be one of the few high-grade geothermal resources in Alaska with a potential for further development as a geothermal energy resource. However, there is paucity of data and limited understanding and characterization of this system for optimal resource development. We used cloud-free summer-time thermal infrared (TIR) images

163

Dynamical Interpretation of Satellite-Sensed Thermal Features off Vancouver Island  

Science Conference Proceedings (OSTI)

Two series of very high resolution thermal infrared satellite images, off Vancouver Island, are examined for evidence of baroclinic waves. A 1979 winter sequence of three images exhibits cold tongues, extending seaward from Vancouver Island, ...

William J. Emery; Lawrence A. Mysak

1980-06-01T23:59:59.000Z

164

NIST Image Gallery: Image Details  

Science Conference Proceedings (OSTI)

... 72 DPI Image 150 DPI Image No 300 DPI Version. Title: NIST Finds that Ethanol-Loving Bacteria Accelerate Cracking of Pipeline Steels. ...

165

Fusion of visual and thermal signatures with eyeglass removal for robust face recognition  

E-Print Network (OSTI)

Abstract This paper describes a fusion of visual and thermal infrared (IR) images for robust face recognition. Two types of fusion methods are discussed: data fusion and decision fusion. Data fusion produces an illumination-invariant face image by adaptively integrating registered visual and thermal face images. Decision fusion combines matching scores of individual face recognition modules. In the data fusion process, eyeglasses, which block thermal energy, are detected from thermal images and replaced with an eye template. Three fusion-based face recognition techniques are implemented and tested: Data fusion of visual and thermal images (Df), Decision fusion with highest matching score (Fh), and Decision fusion with average matching score (Fa). A commercial face recognition software FaceIt is used as an individual recognition module. Comparison results show that fusion-based face recognition techniques outperformed individual visual and thermal face recognizers under illumination variations and facial expressions. I.

Jingu Heo; Seong G. Kong; Besma R. Abidi; Mongi A. Abidi

2004-01-01T23:59:59.000Z

166

Photodetectors with passive thermal radiation control  

DOE Patents (OSTI)

A new class of photodetectors which include means for passive shielding against undesired thermal radiation is disclosed. Such devices can substitute in applications currently requiring cooled optical sensors, such as IR detection and imaging. This description is included for purposes of searching, and is not intended to limit or otherwise influence the interpretation of the present invention.

Lin, Shawn-Yu (Albuquerque, NM); Fleming, James G. (Albuquerque, NM); Dodson, Brian W. (Albuquerque, NM)

2001-10-02T23:59:59.000Z

167

NIST Image Gallery: Image Details  

Science Conference Proceedings (OSTI)

... Title: Scanning tunneling microscope; Semiconductor; Spintronics. Description: [Left] A high resolution STM image of a manganese ...

168

NIST Image Gallery: Image Details  

Science Conference Proceedings (OSTI)

... Title: Nanotechnology--Nanomanufacturing; Optical Nano Vision. Description: A new optical imaging technology under ...

169

SPIE Medical Imaging Medical Imaging  

E-Print Network (OSTI)

1 SPIE Medical Imaging 2006 1 Medical Imaging Fundamentals Kenneth H. Wong, Ph.D. Division of Computer Assisted Interventions and Medical Robotics (CAIMR) Imaging Science and Information Systems (ISIS) Center Department of Radiology Georgetown University SPIE Medical Imaging 2006 2 Main Themes · Describe

Miga, Michael I.

170

HEATS: Thermal Energy Storage  

SciTech Connect

HEATS Project: The 15 projects that make up ARPA-Es HEATS program, short for High Energy Advanced Thermal Storage, seek to develop revolutionary, cost-effective ways to store thermal energy. HEATS focuses on 3 specific areas: 1) developing high-temperature solar thermal energy storage capable of cost-effectively delivering electricity around the clock and thermal energy storage for nuclear power plants capable of cost-effectively meeting peak demand, 2) creating synthetic fuel efficiently from sunlight by converting sunlight into heat, and 3) using thermal energy storage to improve the driving range of electric vehicles (EVs) and also enable thermal management of internal combustion engine vehicles.

None

2012-01-01T23:59:59.000Z

171

Image Logs | Open Energy Information  

Open Energy Info (EERE)

Image Logs Image Logs Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Technique: Image Logs Details Activities (2) Areas (1) Regions (0) NEPA(0) Exploration Technique Information Exploration Group: Downhole Techniques Exploration Sub Group: Well Log Techniques Parent Exploration Technique: Well Log Techniques Information Provided by Technique Lithology: Identify different lithological layers, rock composition, grain size, mineral, and clay content Stratigraphic/Structural: -Fault and fracture identification -Rock texture, porosity, and stress analysis -determine dip, thickness, and geometry of rock strata in vicinity of borehole -Detection of permeable pathways, fracture zones, faults Hydrological: Locate zones of aquifer inflow/outflow Thermal:

172

Rapid Damage eXplorer (RDX): A Probabilistic Framework for Learning Changes From Bitemporal Images  

SciTech Connect

Recent decade has witnessed major changes on the Earth, for example, deforestation, varying cropping and human settlement patterns, and crippling damages due to disasters. Accurate damage assessment caused by major natural and anthropogenic disasters is becoming critical due to increases in human and economic loss. This increase in loss of life and severe damages can be attributed to the growing population, as well as human migration to the disaster prone regions of the world. Rapid assessment of these changes and dissemination of accurate information is critical for creating an effective emergency response. Change detection using high-resolution satellite images is a primary tool in assessing damages, monitoring biomass and critical infrastructures, and identifying new settlements. In this demo, we present a novel supervised probabilistic framework for identifying changes using very high-resolution multispectral, and bitemporal remote sensing images. Our demo shows that the rapid damage explorer (RDX) system is resilient to registration errors and differing sensor characteristics.

Vatsavai, Raju [ORNL

2012-01-01T23:59:59.000Z

173

Improving Battery Design with Electro-Thermal Modeling  

DOE Green Energy (OSTI)

Operating temperature greatly affects the performance and life of batteries in electric and hybrid vehicles. Increased attention is necessary to battery thermal management. Electrochemical models and finite element analysis tools are available for predicting the thermal performance of batteries, but each has limitations. In this study we describe an electro-thermal finite element approach that predicts the thermal performance of a cell or module with realistic geometry. To illustrate the process, we simulated the thermal performance of two generations of Panasonic prismatic nickel-metal-hydride modules used in the Toyota Prius. The model showed why the new generation of Panasonic modules had better thermal performance. Thermal images from two battery modules under constant current discharge indicate that the model predicts the experimental trend reasonably well.

Bharathan, D.; Pesaran, A.; Vlahinos, A.; Kim, G.-H.

2005-01-01T23:59:59.000Z

174

Thermal contact resistance  

E-Print Network (OSTI)

This work deals with phenomena of thermal resistance for metallic surfaces in contact. The main concern of the work is to develop reliable and practical methods for prediction of the thermal contact resistance for various ...

Mikic, B. B.

1966-01-01T23:59:59.000Z

175

Thermal and Electrical Transport in Oxide Heterostructures  

E-Print Network (OSTI)

of thermal conductivity . . . . . . . . . . . . . . . .4.4 Thermal transport in2.3.2 Thermal transport . . . . . . . . . . . . . . . .

Ravichandran, Jayakanth

2011-01-01T23:59:59.000Z

176

Thermal Spray Coatings  

Science Conference Proceedings (OSTI)

Table 35   Thermal spray coatings used for hardfacing applications...piston ring (internal combustion);

177

Plasma-Thermal Synthesis  

INLs Plasma-Thermal Synthesis process improves the conversion process for natural gas into liquid hydrocarbon fuels.

178

Ocean Thermal Energy Conversion  

Energy.gov (U.S. Department of Energy (DOE))

A process called ocean thermal energy conversion (OTEC) uses the heat energy stored in the Earth's oceans to generate electricity.

179

Nanocomposite Thermal Spray Coatings.  

Science Conference Proceedings (OSTI)

Long-Term Surface Restoration Effect Introduced by Advanced Lubricant Additive Nanocomposite Thermal Spray Coatings. New Hardfacing Overlay Claddings...

180

Thermal Management of Solar Cells  

E-Print Network (OSTI)

phonon transmission and interface thermal conductance acrossF. Miao, et al. , "Superior Thermal Conductivity of Single-Advanced Materials for Thermal Management of Electronic

Saadah, Mohammed Ahmed

2013-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "imaging multispectral thermal" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Hyperspectral Imaging | Open Energy Information  

Open Energy Info (EERE)

Hyperspectral Imaging Hyperspectral Imaging Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Technique: Hyperspectral Imaging Details Activities (4) Areas (4) Regions (1) NEPA(1) Exploration Technique Information Exploration Group: Remote Sensing Techniques Exploration Sub Group: Passive Sensors Parent Exploration Technique: Passive Sensors Information Provided by Technique Lithology: mineral maps can be used to show the presence of hydrothermal minerals and mineral assemblages Stratigraphic/Structural: aerial photographs can show structures Hydrological: delineate locations of surface water features Thermal: vegetation maps can show plants stressed due to nearby thermal activity Cost Information Low-End Estimate (USD): 8.63863 centUSD 0.00863 kUSD 8.63e-6 MUSD

182

Thermal neutron detection system  

DOE Patents (OSTI)

According to the present invention, a system for measuring a thermal neutron emission from a neutron source, has a reflector/moderator proximate the neutron source that reflects and moderates neutrons from the neutron source. The reflector/moderator further directs thermal neutrons toward an unmoderated thermal neutron detector.

Peurrung, Anthony J. (Richland, WA); Stromswold, David C. (West Richland, WA)

2000-01-01T23:59:59.000Z

183

Remote sensing for detection of cotton aphid- (Homoptera : Aphididae) and spider mite- (Acari : Tetranychidae) infested cotton in the San Joaquin Valley  

E-Print Network (OSTI)

using multispectral remote sensing. Proc. Beltwide Cottonusing multispectral remote sensing. Proc. Beltwide CottonRichards, J.A. 1993. Remote sensing digital image analysis.

Reisig, D; Godfrey, L

2006-01-01T23:59:59.000Z

184

NIST Image Gallery: Image Details  

Science Conference Proceedings (OSTI)

... Title: Carbon Nanotube Measurements. Description: Scanning electron microscope image of 'cleaned' carbon nanotubes at NIST (color added for ...

185

NIST Image Gallery: Image Details  

Science Conference Proceedings (OSTI)

... Description: Engineering design image shows a cross-section of part of the planned ITER fusion reaction vessel. Diverter ...

186

Property:ThermalInfo | Open Energy Information  

Open Energy Info (EERE)

Property Property Edit with form History Facebook icon Twitter icon » Property:ThermalInfo Jump to: navigation, search Property Name ThermalInfo Property Type Text Subproperties This property has the following 93 subproperties: A Acoustic Logs Active Seismic Methods Active Sensors Aeromagnetic Survey Airborne Electromagnetic Survey Analytical Modeling C Caliper Log Cation Geothermometers Cement Bond Log Conceptual Model Controlled Source Frequency-Domain Magnetics Cross-Dipole Acoustic Log Cuttings Analysis D Data Acquisition-Manipulation Data Collection and Mapping Data Techniques Data and Modeling Techniques Density Log Direct-Current Resistivity Survey Drilling Methods E Earth Tidal Analysis Electric Micro Imager Log Electromagnetic Sounding Methods Elemental Analysis with Fluid Inclusion

187

Building Energy Software Tools Directory: Thermal Comfort  

NLE Websites -- All DOE Office Websites (Extended Search)

Thermal Comfort Thermal Comfort logo. Provides a user-friendly interface for calculating thermal comfort parameters and making thermal comfort predictions using several thermal...

188

Image Resources  

NLE Websites -- All DOE Office Websites (Extended Search)

Mosaic of earth and sky images Mosaic of earth and sky images Image Resources Free image resources covering energy, environment, and general science. Here are some links to energy- and environment-related photographic databases. Berkeley Lab Photo Archive Berkeley Lab's online digital image collection. National Science Digital Library (NSDL) NSDL is the Nation's online library for education and research in science, technology, engineering, and mathematics. The World Bank Group Photo Library A distinctive collection of over 11,000 images that illustrate development through topics such as Agriculture, Education, Environment, Health, Trade and more. Calisphere Compiles the digital collections of libraries, museums, and cultural heritage organizations across California, and organizes them by theme, such

189

Catalytic thermal barrier coatings  

Science Conference Proceedings (OSTI)

A catalyst element (30) for high temperature applications such as a gas turbine engine. The catalyst element includes a metal substrate such as a tube (32) having a layer of ceramic thermal barrier coating material (34) disposed on the substrate for thermally insulating the metal substrate from a high temperature fuel/air mixture. The ceramic thermal barrier coating material is formed of a crystal structure populated with base elements but with selected sites of the crystal structure being populated by substitute ions selected to allow the ceramic thermal barrier coating material to catalytically react the fuel-air mixture at a higher rate than would the base compound without the ionic substitutions. Precious metal crystallites may be disposed within the crystal structure to allow the ceramic thermal barrier coating material to catalytically react the fuel-air mixture at a lower light-off temperature than would the ceramic thermal barrier coating material without the precious metal crystallites.

Kulkarni, Anand A. (Orlando, FL); Campbell, Christian X. (Orlando, FL); Subramanian, Ramesh (Oviedo, FL)

2009-06-02T23:59:59.000Z

190

Simultaneous hierarchical segmentation and vectorization of satellite images through combined data sampling and anisotropic triangulation  

SciTech Connect

The automatic detection, recognition , and segmentation of object classes in remote sensed images is of crucial importance for scene interpretation and understanding. However, it is a difficult task because of the high variability of satellite data. Indeed, the observed scenes usually exhibit a high degree of complexity, where complexity refers to the large variety of pictorial representations of objects with the same semantic meaning and also to the extensive amount of available det.ails. Therefore, there is still a strong demand for robust techniques for automatic information extraction and interpretation of satellite images. In parallel, there is a growing interest in techniques that can extract vector features directly from such imagery. In this paper, we investigate the problem of automatic hierarchical segmentation and vectorization of multispectral satellite images. We propose a new algorithm composed of the following steps: (i) a non-uniform sampling scheme extracting most salient pixels in the image, (ii) an anisotropic triangulation constrained by the sampled pixels taking into account both strength and directionality of local structures present in the image, (iii) a polygonal grouping scheme merging, through techniques based on perceptual information , the obtained segments to a smaller quantity of superior vectorial objects. Besides its computational efficiency, this approach provides a meaningful polygonal representation for subsequent image analysis and/or interpretation.

Grazzini, Jacopo [Los Alamos National Laboratory; Prasad, Lakshman [Los Alamos National Laboratory; Dillard, Scott [PNNL

2010-10-21T23:59:59.000Z

191

Thermally Conductive Graphite Foam  

oriented graphite planes, similar to high performance carbon fibers, which have been estimated to exhibit a thermal conductivity greater than 1700 ...

192

Thermal Barrier Coatings  

NLE Websites -- All DOE Office Websites (Extended Search)

Thermal Barrier Coatings Opportunity The Department of Energy's National Energy Technology Laboratory (NETL) is seeking licensing partners interested in implementing United States...

193

NIST Image Gallery: Image Details  

Science Conference Proceedings (OSTI)

... on the availability of this image. Title: Tiny Tubes May Aid Pharmacuetical R&D. Description: NIST scientists used pairs of ...

194

NIST Image Gallery: Image Details  

Science Conference Proceedings (OSTI)

... Magneto-optical image of magnetic fields within a YBCO superconductor showing electrically ... PHY, High-Temp Superconductors See also http ...

195

NIST Image Gallery: Image Details  

Science Conference Proceedings (OSTI)

... Title: New Imaging Tool is Boon to Fuel Cell Research. ... water being produced and removed inside the maze-like solid housing of fuel cells under a ...

196

THERMAL PHASES OF EARTH-LIKE PLANETS: ESTIMATING THERMAL INERTIA FROM ECCENTRICITY, OBLIQUITY, AND DIURNAL FORCING  

SciTech Connect

In order to understand the climate on terrestrial planets orbiting nearby Sun-like stars, one would like to know their thermal inertia. We use a global climate model to simulate the thermal phase variations of Earth analogs and test whether these data could distinguish between planets with different heat storage and heat transport characteristics. In particular, we consider a temperate climate with polar ice caps (like the modern Earth) and a snowball state where the oceans are globally covered in ice. We first quantitatively study the periodic radiative forcing from, and climatic response to, rotation, obliquity, and eccentricity. Orbital eccentricity and seasonal changes in albedo cause variations in the global-mean absorbed flux. The responses of the two climates to these global seasons indicate that the temperate planet has 3 Multiplication-Sign the bulk heat capacity of the snowball planet due to the presence of liquid water oceans. The obliquity seasons in the temperate simulation are weaker than one would expect based on thermal inertia alone; this is due to cross-equatorial oceanic and atmospheric energy transport. Thermal inertia and cross-equatorial heat transport have qualitatively different effects on obliquity seasons, insofar as heat transport tends to reduce seasonal amplitude without inducing a phase lag. For an Earth-like planet, however, this effect is masked by the mixing of signals from low thermal inertia regions (sea ice and land) with that from high thermal inertia regions (oceans), which also produces a damped response with small phase lag. We then simulate thermal light curves as they would appear to a high-contrast imaging mission (TPF-I/Darwin). In order of importance to the present simulations, which use modern-Earth orbital parameters, the three drivers of thermal phase variations are (1) obliquity seasons, (2) diurnal cycle, and (3) global seasons. Obliquity seasons are the dominant source of phase variations for most viewing angles. A pole-on observer would measure peak-to-trough amplitudes of 13% and 47% for the temperate and snowball climates, respectively. Diurnal heating is important for equatorial observers ({approx}5% phase variations), because the obliquity effects cancel to first order from that vantage. Finally, we compare the prospects of optical versus thermal direct imaging missions for constraining the climate on exoplanets and conclude that while zero- and one-dimensional models are best served by thermal measurements, second-order models accounting for seasons and planetary thermal inertia would require both optical and thermal observations.

Cowan, Nicolas B. [Center for Interdisciplinary Exploration and Research in Astrophysics and Department of Physics and Astronomy, Northwestern University, 2131 Tech Drive, Evanston, IL 60208 (United States); Voigt, Aiko [Max Planck Institute for Meteorology, Bundesstr. 53, D-20146 Hamburg (Germany); Abbot, Dorian S., E-mail: n-cowan@nortwestern.edu [Department of Geophysical Sciences, University of Chicago, 5734 South Ellis Avenue, Chicago, IL 60637 (United States)

2012-09-20T23:59:59.000Z

197

Variable pressure thermal insulating jacket  

DOE Patents (OSTI)

A device for controlled insulation of a thermal device. The device includes a thermal jacket with a closed volume able to be evacuated to form an insulating jacket around the thermal source. A getter material is in communcation with the closed volume of the thermal jacket. The getter material can absorb and desorb a control gas to control gas pressure in the volume of the thermal jacket to control thermal conductivity in the thermal jacket.

Nelson, Paul A. (Wheaton, IL); Malecha, Richard F. (Naperville, IL); Chilenskas, Albert A. (Chicago, IL)

1994-01-01T23:59:59.000Z

198

Variable pressure thermal insulating jacket  

DOE Patents (OSTI)

A device for controlled insulation of a thermal device is disclosed. The device includes a thermal jacket with a closed volume able to be evacuated to form an insulating jacket around the thermal source. A getter material is in communication with the closed volume of the thermal jacket. The getter material can absorb and desorb a control gas to control gas pressure in the volume of the thermal jacket to control thermal conductivity in the thermal jacket. 10 figs.

Nelson, P.A.; Malecha, R.F.; Chilenskas, A.A.

1994-09-20T23:59:59.000Z

199

Thermal protection apparatus  

DOE Patents (OSTI)

An apparatus which thermally protects sensitive components in tools used in a geothermal borehole. The apparatus comprises a Dewar within a housing. The Dewar contains heat pipes such as brass heat pipes for thermally conducting heat from heat sensitive components to a heat sink such as ice.

Bennett, Gloria A. (Los Alamos, NM); Elder, Michael G. (Los Alamos, NM); Kemme, Joseph E. (Albuquerque, NM)

1985-01-01T23:59:59.000Z

200

Thermal protection apparatus  

DOE Patents (OSTI)

The disclosure is directed to an apparatus for thermally protecting sensitive components in tools used in a geothermal borehole. The apparatus comprises a Dewar within a housing. The Dewar contains heat pipes such as brass heat pipes for thermally conducting heat from heat sensitive components such as electronics to a heat sink such as ice.

Bennett, G.A.; Elder, M.G.; Kemme, J.E.

1984-03-20T23:59:59.000Z

Note: This page contains sample records for the topic "imaging multispectral thermal" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Thermal masses in leptogenesis  

E-Print Network (OSTI)

We investigate the validity of using thermal masses in the kinematics of final states in the decay rate of heavy neutrinos in leptogenesis calculations. We find that using thermal masses this way is a reasonable approximation, but corrections arise through quantum statistical distribution functions and leptonic quasiparticles.

Kiessig, Clemens P

2009-01-01T23:59:59.000Z

202

Thermal treatment wall  

DOE Patents (OSTI)

A thermal treatment wall emplaced to perform in-situ destruction of contaminants in groundwater. Thermal destruction of specific contaminants occurs by hydrous pyrolysis/oxidation at temperatures achievable by existing thermal remediation techniques (electrical heating or steam injection) in the presence of oxygen or soil mineral oxidants, such as MnO.sub.2. The thermal treatment wall can be installed in a variety of configurations depending on the specific objectives, and can be used for groundwater cleanup, wherein in-situ destruction of contaminants is carried out rather than extracting contaminated fluids to the surface, where they are to be cleaned. In addition, the thermal treatment wall can be used for both plume interdiction and near-wellhead in-situ groundwater treatment. Thus, this technique can be utilized for a variety of groundwater contamination problems.

Aines, Roger D. (Livermore, CA); Newmark, Robin L. (Livermore, CA); Knauss, Kevin G. (Livermore, CA)

2000-01-01T23:59:59.000Z

203

Solar thermal aircraft  

DOE Patents (OSTI)

A solar thermal powered aircraft powered by heat energy from the sun. A heat engine, such as a Stirling engine, is carried by the aircraft body for producing power for a propulsion mechanism, such as a propeller. The heat engine has a thermal battery in thermal contact with it so that heat is supplied from the thermal battery. A solar concentrator, such as reflective parabolic trough, is movably connected to an optically transparent section of the aircraft body for receiving and concentrating solar energy from within the aircraft. Concentrated solar energy is collected by a heat collection and transport conduit, and heat transported to the thermal battery. A solar tracker includes a heliostat for determining optimal alignment with the sun, and a drive motor actuating the solar concentrator into optimal alignment with the sun based on a determination by the heliostat.

Bennett, Charles L. (Livermore, CA)

2007-09-18T23:59:59.000Z

204

Images, Video, & More  

NLE Websites -- All DOE Office Websites (Extended Search)

Images, Video, & More Images BABAR Design drawings SLAC Image Gallery: BABAR SLAC Image Gallery: Aerial photos Videos Public lecture on "ANTIMATTER: What is it and where did it...

205

Development of Non?Tracking Solar Thermal Technology  

Science Conference Proceedings (OSTI)

The aims of this research is to develop high temperature solar thermal collectors that do not require complex solar tracking devices to maintain optimal performance. The collector technology developed through these efforts uses non?imaging optics and is referred to as an external compound parabolic concentrator. It is able to operate with a solar thermal efficiency of approximately 50% at a temperature of 200??C and can be readily manufactured at a cost between $15 and $18 per square foot.

2011-01-01T23:59:59.000Z

206

Two-photon interference with true thermal light  

E-Print Network (OSTI)

Two-photon interference and "ghost" imaging with entangled light have attracted much attention since the last century because of the novel features such as non-locality and sub-wavelength effect. Recently, it has been found that pseudo-thermal light can mimic certain effects of entangled light. We report here the first observation of two-photon interference with true thermal light.

Yan-Hua Zhai; Xi-Hao Chen; Da Zhang; Ling-An Wu

2005-06-07T23:59:59.000Z

207

Thermally-related safety issues associated with thermal batteries.  

DOE Green Energy (OSTI)

Thermal batteries can experience thermal runaway under certain usage conditions. This can lead to safety issues for personnel and cause damage to associated test equipment if the battery thermally self destructs. This report discusses a number of thermal and design related issues that can lead to catastrophic destruction of thermal batteries under certain conditions. Contributing factors are identified and mitigating actions are presented to minimize or prevent undesirable thermal runaway.

Guidotti, Ronald Armand

2006-06-01T23:59:59.000Z

208

Damage Evolution in Thermal Barrier Coatings with Thermal Cycling  

Science Conference Proceedings (OSTI)

Abstract Scope, Thermal barrier coatings typically fail on cooling after prolonged thermal cycling by the growth of sub-critical interface separations. Observations...

209

Efficient thermal management for multiprocessor systems  

E-Print Network (OSTI)

2.2.4 Thermal Modeling . . . . . . . .63 Table 4.3: Thermal Hot Spots . . . . . . . . . . . . . .Performance-Efficient Thermal Management . . . . . . . . . .

Co?kun, Ay?e K?v?lc?m

2009-01-01T23:59:59.000Z

210

Cooling thermal storage  

Science Conference Proceedings (OSTI)

This article gives some overall guidelines for successful operation of cooling thermal storage installations. Electric utilities use rates and other incentives to encourage thermal storage, which not only reduces their system peaks but also transfers a portion of their load from expensive daytime inefficient peaking plants to less expensive nighttime base load high efficiency coal and nuclear plants. There are hundreds of thermal storage installations around the country. Some of these are very successful; others have failed to achieve all of their predicted benefits because application considerations were not properly addressed.

Gatley, D.P.

1987-04-01T23:59:59.000Z

211

Solar Thermal Conversion  

DOE Green Energy (OSTI)

The thermal conversion process of solar energy is based on well-known phenomena of heat transfer (Kreith 1976). In all thermal conversion processes, solar radiation is absorbed at the surface of a receiver, which contains or is in contact with flow passages through which a working fluid passes. As the receiver heats up, heat is transferred to the working fluid which may be air, water, oil, or a molten salt. The upper temperature that can be achieved in solar thermal conversion depends on the insolation, the degree to which the sunlight is concentrated, and the measures taken to reduce heat losses from the working fluid.

Kreith, F.; Meyer, R. T.

1982-11-01T23:59:59.000Z

212

Multilayer thermal barrier coating systems  

DOE Patents (OSTI)

The present invention generally describes multilayer thermal barrier coating systems and methods of making the multilayer thermal barrier coating systems. The thermal barrier coating systems comprise a first ceramic layer, a second ceramic layer, a thermally grown oxide layer, a metallic bond coating layer and a substrate. The thermal barrier coating systems have improved high temperature thermal and chemical stability for use in gas turbine applications.

Vance, Steven J. (Orlando, FL); Goedjen, John G. (Oviedo, FL); Sabol, Stephen M. (Orlando, FL); Sloan, Kelly M. (Longwood, FL)

2000-01-01T23:59:59.000Z

213

NIST Image Gallery: Image Details  

Science Conference Proceedings (OSTI)

... from the bright glare in the distance transmit images of a cat-like face at ... Though false color has been added to the cats faces, they are otherwise ...

214

NIST Image Gallery: Image Details  

Science Conference Proceedings (OSTI)

... a href http://www.nist.gov/public_affairs/images/Nanopore 20device.avi See video /a PHY, DARPA, spectroscopy See also http://www.nist.gov/pml ...

215

Thermal insulations using vacuum panels  

DOE Patents (OSTI)

Thermal insulation vacuum panels are formed of an inner core of compressed low thermal conductivity powders enclosed by a ceramic/glass envelope evaluated to a low pressure.

Glicksman, Leon R. (Lynnfield, MA); Burke, Melissa S. (Pittsburgh, PA)

1991-07-16T23:59:59.000Z

216

Ocean Thermal | Open Energy Information  

Open Energy Info (EERE)

Community Login | Sign Up Search Page Edit History Facebook icon Twitter icon Ocean Thermal Jump to: navigation, search TODO: Add description List of Ocean Thermal Incentives...

217

Comparison of Thermal Insulation Materials.  

E-Print Network (OSTI)

??This thesis is about comparing of different thermal insulation materials of different manufactures. In our days there are a lot of different thermal insulation materials (more)

Chaykovskiy, German

2010-01-01T23:59:59.000Z

218

Integrability vs Quantum Thermalization  

E-Print Network (OSTI)

Non-integrability is often taken as a prerequisite for quantum thermalization. Still, a generally accepted definition of quantum integrability is lacking. With the basis in the driven Rabi model we discuss this careless usage of the term "integrability" in connection to quantum thermalization. The model would be classified as non-integrable according to the most commonly used definitions, for example, the only preserved quantity is the total energy. Despite this fact, a thorough analysis conjectures that the system will not thermalize. Thus, our findings suggest first of all (i) that care should be paid when linking non-integrability with thermalization, and secondly (ii) that the standardly used definitions for quantum integrability are unsatisfactory.

Jonas Larson

2013-04-12T23:59:59.000Z

219

Contact thermal lithography  

E-Print Network (OSTI)

Contact thermal lithography is a method for fabricating microscale patterns using heat transfer. In contrast to photolithography, where the minimum achievable feature size is proportional to the wavelength of light used ...

Schmidt, Aaron Jerome, 1979-

2004-01-01T23:59:59.000Z

220

Properties of Thermal Glueballs  

E-Print Network (OSTI)

We study the properties of the 0++ glueball at finite temperature using SU(3) quenched lattice QCD. We find a significant thermal effects near T_c. We perform the \\chi^2 fit analyses adopting two Ansaetze for the spectral function, i.e., the conventional narrow-peak Ansatz and an advanced Breit-Wigner Ansatz. The latter is an extension of the former, taking account of the appearance of the thermal width at T>0. We also perform the MEM analysis. These analyses indicate that the thermal effect on the glueball is a significant thermal-width broadening \\Gamma(T_c) \\sim 300 MeV together with a modest reduction in the peak center \\Delta\\omega_0(T_c) \\sim 100 MeV.

Noriyoshi Ishii; Hideo Suganuma

2003-12-27T23:59:59.000Z

Note: This page contains sample records for the topic "imaging multispectral thermal" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Thermal springs of Wyoming  

SciTech Connect

This bulletin attempts, first, to provide a comprehensive inventory of the thermal springs of Wyoming; second, to explore the geologic and hydrologic factors producing these springs; and, third, to analyze the springs collectively as an indicator of the geothermal resources of the state. A general discussion of the state's geology and the mechanisms of thermal spring production, along with a brief comparison of Wyoming's springs with worldwide thermal features are included. A discussion of geothermal energy resources, a guide for visitors, and an analysis of the flora of Wyoming's springs follow the spring inventory. The listing and analysis of Wyoming's thermal springs are arranged alphabetically by county. Tabulated data are given on elevation, ownership, access, water temperature, and flow rate. Each spring system is described and its history, general characteristics and uses, geology, hydrology, and chemistry are discussed. (MHR)

Breckenridge, R.M.; Hinckley, B.S.

1978-01-01T23:59:59.000Z

222

Thermal springs of Wyoming  

DOE Green Energy (OSTI)

This bulletin attempts, first, to provide a comprehensive inventory of the thermal springs of Wyoming; second, to explore the geologic and hydrologic factors producing these springs; and, third, to analyze the springs collectively as an indicator of the geothermal resources of the state. A general discussion of the state's geology and the mechanisms of thermal spring production, along with a brief comparison of Wyoming's springs with worldwide thermal features are included. A discussion of geothermal energy resources, a guide for visitors, and an analysis of the flora of Wyoming's springs follow the spring inventory. The listing and analysis of Wyoming's thermal springs are arranged alphabetically by county. Tabulated data are given on elevation, ownership, access, water temperature, and flow rate. Each spring system is described and its history, general characteristics and uses, geology, hydrology, and chemistry are discussed. (MHR)

Breckenridge, R.M.; Hinckley, B.S.

1978-01-01T23:59:59.000Z

223

Solar Thermal Manufacturing Activities  

Reports and Publications (EIA)

This report, Solar Thermal Collector Manufacturing Activities, providesan overview and tables with historical data spanning 2000-2009. These tables willcorrespond to similar tables to be presented in the Renewable Energy Annual 2009 andare numbered accordingly.

Michele Simmons

2010-12-01T23:59:59.000Z

224

Texas Thermal Comfort Report  

NLE Websites -- All DOE Office Websites (Extended Search)

thermal comfort thermal comfort Too often, the systems in our houses are both physically and intellectually inaccessible. In the SNAP House, HVAC components are integrated into the overall structure, and act as an experiential threshold between public and private spaces. They are located in a central, structural chase that supports the clerestory and gives the systems a functional presence within the interior. Each individual component is contained within a single chase

225

Photovoltaic-thermal collectors  

DOE Patents (OSTI)

A photovoltaic-thermal solar cell including a semiconductor body having antireflective top and bottom surfaces and coated on each said surface with a patterned electrode covering less than 10% of the surface area. A thermal-absorbing surface is spaced apart from the bottom surface of the semiconductor and a heat-exchange fluid is passed between the bottom surface and the heat-absorbing surface.

Cox, III, Charles H. (Carlisle, MA)

1984-04-24T23:59:59.000Z

226

Thermal Energy Storage  

Science Conference Proceedings (OSTI)

This Technology Brief provides an update on the current state of cool thermal energy storage systems (TES) for end-use applications. Because of its ability to shape energy use, TES is strategic technology that allows end-users to reduce their energy costs while simultaneously providing benefits for electric utilities through persistent peak demand reduction and peak shifting. In addition to discussing the concepts of thermal energy storage, the Brief discusses the current state of TES technologies and dr...

2008-12-16T23:59:59.000Z

227

Quantitative Luminescence Imaging System  

SciTech Connect

The goal of the MEASUREMENT OF CHEMILUMINESCENCE project is to develop and deliver a suite of imaging radiometric instruments for measuring spatial distributions of chemiluminescence. Envisioned deliverables include instruments working at the microscopic, macroscopic, and life-sized scales. Both laboratory and field portable instruments are envisioned. The project also includes development of phantoms as enclosures for the diazoluminomelanin (DALM) chemiluminescent chemistry. A suite of either phantoms in a variety of typical poses, or phantoms that could be adjusted to a variety of poses, is envisioned. These are to include small mammals (rats), mid-sized mammals (monkeys), and human body parts. A complete human phantom that can be posed is a long-term goal of the development. Taken together, the chemistry and instrumentation provide a means for imaging rf dosimetry based on chemiluminescence induced by the heat resulting from rf energy absorption. The first delivered instrument, the Quantitative Luminescence Imaging System (QLIS), resulted in a patent, and an R&D Magazine 1991 R&D 100 award, recognizing it as one of the 100 most significant technological developments of 1991. The current status of the project is that three systems have been delivered, several related studies have been conducted, two preliminary human hand phantoms have been delivered, system upgrades have been implemented, and calibrations have been maintained. Current development includes sensitivity improvements to the microscope-based system; extension of the large-scale (potentially life-sized targets) system to field portable applications; extension of the 2-D large-scale system to 3-D measurement; imminent delivery of a more refined human hand phantom and a rat phantom; rf, thermal and imaging subsystem integration; and continued calibration and upgrade support.

Batishko, C.R.; Stahl, K.A.; Fecht, B.A.

1992-12-31T23:59:59.000Z

228

History Images  

NLE Websites -- All DOE Office Websites (Extended Search)

History Images History Images Los Alamos History in Images Los Alamos has a proud history and heritage of almost 70 years of science and innovation. The people of the Laboratory work on advanced technologies to provide the best scientific and engineering solutions to many of the nation's most crucial security challenges. Click thumbnails to enlarge. Photos arranged by most recent first, horizontal formats before vertical. See Flickr for more sizes and details. Back in the day Back in the day LA bridge in Los Alamos LA bridge in Los Alamos 1945 Army-Navy "E" Award 1945 Army-Navy "E" Award Louis Rosen Louis Rosen Bob Van Ness Robert Kuckuck and Michael Anastasio Bob Van Ness Robert Kuckuck and Michael Anastasio TA-18 TA-18 Elmer Island TU-4 assembly area Elmer Island TU-4 assembly area

229

Thermal Performance Engineer's Handbook: Introduction to Thermal Performance  

Science Conference Proceedings (OSTI)

The two-volume Thermal Performance Engineer Handbook will assist thermal performance engineers in identifying and investigating the cause of megawatt (MWe) losses as well as in proposing new ways to increase MWe output. Volume 1 contains a thermal performance primer to provide a brief review of thermodynamic principles involved in the stream power plant thermal cycle. The primer also contains brief descriptions of the equipment and systems in the cycle that can be sources of thermal losses. Also in Volum...

1998-04-01T23:59:59.000Z

230

HEAVY AND THERMAL OIL RECOVERY PRODUCTION MECHANISMS  

Science Conference Proceedings (OSTI)

This technical progress report describes work performed from April 1 through June 30, 2002, for the project ''Heavy and Thermal Oil Recovery Production Mechanisms.'' We investigate a broad spectrum of topics related to thermal and heavy-oil recovery. Significant results were obtained in the areas of multiphase flow and rock properties, hot-fluid injection, improved primary heavy oil recovery, and reservoir definition. The research tools and techniques used are varied and span from pore-level imaging of multiphase fluid flow to definition of reservoir-scale features through streamline-based history-matching techniques. Briefly, experiments were conducted to image at the pore level matrix-to-fracture production of oil from a fractured porous medium. This project is ongoing. A simulation studied was completed in the area of recovery processes during steam injection into fractured porous media. We continued to study experimentally heavy-oil production mechanisms from relatively low permeability rocks under conditions of high pressure and high temperature. High temperature significantly increased oil recovery rate and decreased residual oil saturation. Also in the area of imaging production processes in laboratory-scale cores, we use CT to study the process of gas-phase formation during solution gas drive in viscous oils. Results from recent experiments are reported here. Finally, a project was completed that uses the producing water-oil ratio to define reservoir heterogeneity and integrate production history into a reservoir model using streamline properties.

Anthony R. Kovscek

2002-07-01T23:59:59.000Z

231

Compound Refractive Lenses for Thermal Neutron Applications  

SciTech Connect

This project designed and built compound refractive lenses (CRLs) that are able to focus, collimate and image using thermal neutrons. Neutrons are difficult to manipulate compared to visible light or even x rays; however, CRLs can provide a powerful tool for focusing, collimating and imaging neutrons. Previous neutron CRLs were limited to long focal lengths, small fields of view and poor resolution due to the materials available and manufacturing techniques. By demonstrating a fabrication method that can produce accurate, small features, we have already dramatically improved the focal length of thermal neutron CRLs, and the manufacture of Fresnel lens CRLs that greatly increases the collection area, and thus efficiency, of neutron CRLs. Unlike a single lens, a compound lens is a row of N lenslets that combine to produce an N-fold increase in the refraction of neutrons. While CRLs can be made from a variety of materials, we have chosen to mold Teflon lenses. Teflon has excellent neutron refraction, yet can be molded into nearly arbitrary shapes. We designed, fabricated and tested Teflon CRLs for neutrons. We demonstrated imaging at wavelengths as short as 1.26 ? with large fields of view and achieved resolution finer than 250 ?m which is better than has been previously shown. We have also determined designs for Fresnel CRLs that will greatly improve performance.

Gary, Charles K.

2013-11-12T23:59:59.000Z

232

Thermal Management of Solar Cells  

E-Print Network (OSTI)

UNIVERSITY OF CALIFORNIA RIVERSIDE Thermal Management ofUniversity of California, Riverside Acknowledgments First, I

Saadah, Mohammed Ahmed

2013-01-01T23:59:59.000Z

233

Multilayer Nanoscale Thermal Barrier Coatings  

Science Conference Proceedings (OSTI)

Advanced high-efficiency gas turbines require thermal barrier coatings (TBCs) with low thermal conductivity and excellent thermal-cycling resistance. The multilayer TBC developed in this project has a thermal conductivity about half that of conventional TBCs and also rejects up to 70 percent of incoming radiant energy.

1999-05-26T23:59:59.000Z

234

Solar-thermal technology  

DOE Green Energy (OSTI)

Solar-thermal technology converts sunlight into thermal energy. It stands alongside other solar technologies including solar-electric and photovoltaic technologies, both of which convert sunlight into electricity. Photovoltaic technology converts by direct conversion, and solar-electric converts by using sunlight`s thermal energy in thermodynamic power cycles. The numerous up-and-running solar energy systems prove solar-thermal technology works. But when is it cost-effective, and how can HVAC engineers and facility owners quickly identify cost-effective applications? This article addresses these questions by guiding the reader through the basics of solar-thermal technology. The first section provides an overview of today`s technology including discussions of collectors and typical systems. The next section presents an easy method for identifying potentially cost-effective applications. This section also identifies sources for obtaining more information on the technology--collector ratings and performance, solar manufacturers, and solar design and analysis tools. The article discusses only those collectors and systems that are most often used. Many others are on the market--the article does not, by omission, mean to infer that one is better than the other.

Bennett, C. [Sandia National Labs., Albuquerque, NM (United States)

1995-09-01T23:59:59.000Z

235

Article for thermal energy storage  

DOE Patents (OSTI)

A thermal energy storage composition is provided which is in the form of a gel. The composition includes a phase change material and silica particles, where the phase change material may comprise a linear alkyl hydrocarbon, water/urea, or water. The thermal energy storage composition has a high thermal conductivity, high thermal energy storage, and may be used in a variety of applications such as in thermal shipping containers and gel packs.

Salyer, Ival O. (Dayton, OH)

2000-06-27T23:59:59.000Z

236

Improving face segmentation in thermograms using image signatures  

Science Conference Proceedings (OSTI)

The aim of this paper is to present a method for the automatic segmentation of face images captured in Long Wavelength Infrared (LWIR), allowing for a large range of face rotations and expressions. The motivation behind this effort is to enable better ... Keywords: face segmentation, human skin segmentation, image segmentation, infrared thermal

Slvio Filipe; Lus A. Alexandre

2010-11-01T23:59:59.000Z

237

Thermal insulated glazing unit  

SciTech Connect

An improved insulated glazing unit is provided which can attain about R5 to about R10 thermal performance at the center of the glass while having dimensions about the same as those of a conventional double glazed insulated glazing unit. An outer glazing and inner glazing are sealed to a spacer to form a gas impermeable space. One or more rigid, non-structural glazings are attached to the inside of the spacer to divide the space between the inner and outer glazings to provide insulating gaps between glazings of from about 0.20 inches to about 0.40 inches. One or more glazing surfaces facing each thermal gap are coated with a low emissivity coating. Finally, the thermal gaps are filled with a low conductance gas such as krypton gas.

Selkowitz, Stephen E. (Piedmont, CA); Arasteh, Dariush K. (Oakland, CA); Hartmann, John L. (Seattle, WA)

1991-01-01T23:59:59.000Z

238

Thermal insulated glazing unit  

DOE Patents (OSTI)

An improved insulated glazing unit is provided which can attain about R5 to about R10 thermal performance at the center of the glass while having dimensions about the same as those of a conventional double glazed insulated glazing unit. An outer glazing and inner glazing are sealed to a spacer to form a gas impermeable space. One or more rigid, non-structural glazings are attached to the inside of the spacer to divide the space between the inner and outer glazings to provide insulating gaps between glazings of from about 0.20 inches to about 0.40 inches. One or more glazing surfaces facing each thermal gap are coated with a low emissivity coating. Finally, the thermal gaps are filled with a low conductance gas such as krypton gas. 2 figs.

Selkowitz, S.E.; Arasteh, D.K.; Hartmann, J.L.

1988-04-05T23:59:59.000Z

239

Thermal energy storage material  

DOE Patents (OSTI)

A thermal energy storage material which is stable at atmospheric temperature and pressure and has a melting point higher than 32.degree.F. is prepared by dissolving a specific class of clathrate forming compounds, such as tetra n-propyl or tetra n-butyl ammonium fluoride, in water to form a substantially solid clathrate. The resultant thermal energy storage material is capable of absorbing heat from or releasing heat to a given region as it transforms between solid and liquid states in response to temperature changes in the region above and below its melting point.

Leifer, Leslie (Hancock, MI)

1976-01-01T23:59:59.000Z

240

Thermal test options  

SciTech Connect

Shipping containers for radioactive materials must be qualified to meet a thermal accident environment specified in regulations, such at Title 10, Code of Federal Regulations, Part 71. Aimed primarily at the shipping container design, this report discusses the thermal testing options available for meeting the regulatory requirements, and states the advantages and disadvantages of each approach. The principal options considered are testing with radiant heat, furnaces, and open pool fires. The report also identifies some of the facilities available and current contacts. Finally, the report makes some recommendations on the appropriate use of these different testing methods.

Koski, J.A.; Keltner, N.R.; Sobolik, K.B.

1993-02-01T23:59:59.000Z

Note: This page contains sample records for the topic "imaging multispectral thermal" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Thermal ignition combustion system  

DOE Patents (OSTI)

The thermal ignition combustion system comprises means for providing walls defining an ignition chamber, the walls being made of a material having a thermal conductivity greater than 20 W/m C and a specific heat greater than 480 J/kg C with the ignition chamber being in constant communication with the main combustion chamber, means for maintaining the temperature of the walls above a threshold temperature capable of causing ignition of a fuel, and means for conducting fuel to the ignition chamber. 8 figs.

Kamo, R.; Kakwani, R.M.; Valdmanis, E.; Woods, M.E.

1988-04-19T23:59:59.000Z

242

Thermal Insulation Systems  

E-Print Network (OSTI)

Thermal insulation systems are receiving a high degree of attention in view of increasing energy cost. Industrial, commercial and residential energy users are all well aware of energy cost increases and great emphasis is being directed to energy cost reduction programs. One of the best places to start with energy conservation is to employ proper insulation systems. This article discusses the significant properties of thermal insulation materials primarily for industrial application. Some of the information is applicable to commercial and residential insulation. Only hot service conditions will be covered.

Stanley, T. F.

1982-01-01T23:59:59.000Z

243

Imaging bolometer  

DOE Patents (OSTI)

Radiation-hard, steady-state imaging bolometer. A bolometer employing infrared (IR) imaging of a segmented-matrix absorber of plasma radiation in a cooled-pinhole camera geometry is described. The bolometer design parameters are determined by modeling the temperature of the foils from which the absorbing matrix is fabricated by using a two-dimensional time-dependent solution of the heat conduction equation. The resulting design will give a steady-state bolometry capability, with approximately 100 Hz time resolution, while simultaneously providing hundreds of channels of spatial information. No wiring harnesses will be required, as the temperature-rise data will be measured via an IR camera. The resulting spatial data may be used to tomographically investigate the profile of plasmas.

Wurden, Glen A. (Los Alamos, NM)

1999-01-01T23:59:59.000Z

244

Imaging bolometer  

DOE Patents (OSTI)

Radiation-hard, steady-state imaging bolometer is disclosed. A bolometer employing infrared (IR) imaging of a segmented-matrix absorber of plasma radiation in a cooled-pinhole camera geometry is described. The bolometer design parameters are determined by modeling the temperature of the foils from which the absorbing matrix is fabricated by using a two-dimensional time-dependent solution of the heat conduction equation. The resulting design will give a steady-state bolometry capability, with approximately 100 Hz time resolution, while simultaneously providing hundreds of channels of spatial information. No wiring harnesses will be required, as the temperature-rise data will be measured via an IR camera. The resulting spatial data may be used to tomographically investigate the profile of plasmas. 2 figs.

Wurden, G.A.

1999-01-19T23:59:59.000Z

245

Mixed phase clouds, cloud electrification and remote sensing.  

SciTech Connect

Most of hypothesis trying to explain charge separation in thunderstorm clouds require presence of ice and supercooled water. Thus the existence of ice or at least mixed phase regions near cloud tops should be a necessary (but not a sufficient) condition for development of lightning. We show that multispectral satellite based instruments, like the DOE MTI (Multispectral Thermal Imager) or NASA MODIS (Moderate Resolution Imaging Spectroradiometer), using the near infrared and visible spectral bands are able to distinguish between water, ice and mixed phase cloud regions. An analysis of the MTI images of mixed phase clouds - with spatial resolution of about 20 m - shows regions of pure water, pure ice as well as regions of water/ice mixtures. We suggest that multispectral satellite instruments may be useful for a short time forecast of lightning probabilities.

Chylek, P. (Petr); Borel, C. C. (Christoph C.); Klett, James

2004-01-01T23:59:59.000Z

246

Uncooled thin film pyroelectric IR detector with aerogel thermal isolation  

Science Conference Proceedings (OSTI)

Uncooled pyroelectric IR imaging systems, such as night vision goggles, offer important strategic advantages in battlefield scenarios and reconnaissance surveys. Until now, the current technology for fabricating these devices has been limited by low throughput and high cost which ultimately limit the availability of these sensor devices. We have developed and fabricated an alternative design for pyroelectric IR imaging sensors that utilizes a multilayered thin film deposition scheme to create a monolithic thin film imaging element on an active silicon substrate for the first time. This approach combines a thin film pyroelectric imaging element with a thermally insulating SiO{sub 2} aerogel thin film to produce a new type of uncooled IR sensor that offers significantly higher thermal, spatial, and temporal resolutions at a substantially lower cost per unit. This report describes the deposition, characterization and optimization of the aerogel thermal isolation layer and an appropriate pyroelectric imaging element. It also describes the overall integration of these components along with the appropriate planarization, etch stop, adhesion, electrode, and blacking agent thin film layers into a monolithic structure. 19 refs., 8 figs., 6 tabs.

Ruffner, J.A.; Clem, P.G.; Tuttle, B.A. [and others

1998-01-01T23:59:59.000Z

247

Cloud classification using whole-sky imager data  

SciTech Connect

Clouds are one of the most important moderators of the earth radiation budget and one of the least understood. The effect that clouds have on the reflection and absorption of solar and terrestrial radiation is strongly influenced by their shape, size, and composition. Physically accurate parameterization of clouds is necessary for any general circulation model (GCM) to yield meaningful results. The work presented here is part of a larger project that is aimed at producing realistic three-dimensional (3D) volume renderings of cloud scenes, thereby providing the important shape information for parameterizing GCMs. The specific goal of the current study is to develop an algorithm that automatically classifies (by cloud type) the clouds observed in the scene. This information will assist the volume rendering program in determining the shape of the cloud. Much work has been done on cloud classification using multispectral satellite images. Most of these references use some kind of texture measure to distinguish the different cloud types and some also use topological features (such as cloud/sky connectivity or total number of clouds). A wide variety of classification methods has been used, including neural networks, various types of clustering, and thresholding. The work presented here utilizes binary decision trees to distinguish the different cloud types based on cloud feature vectors.

Buch, K.A. Jr.; Sun, Chen-Hui

1995-02-01T23:59:59.000Z

248

Building Extraction using LiDAR DEMs and IKONOS Images  

E-Print Network (OSTI)

An automated method for boundary representation of building objects has been considered as a core processor for 3D city modelling. Since the reconstruction of generic building shape fundamentally depends on geometric features extracted from data sources, it suffers difficulties especially when a monocular imagery with high scene complexity is solely used. The research described in this paper aims to develop an automated method for building extraction, in which individual building object is localized and boundaries of polyhedral building shape are delineated with a less specific building model. The developed technique focuses on an exploitation of synergy of Ikonos imagery combined with a LIDAR DEM. Individual buildings are localized with rectangle polygon by a hierarchical segmentation of LIDAR DEM and Ikonos multi-spectral information. This polygon is recursively partitioned by linear features extracted from Ikonos image and LIDAR space, which results in a set of convex polygons. Only polygons comprising significant parts of building shape are verified and aggregated. Finally, polyhedral building shapes are reconstructed. Several results are presented with a discussion of evaluation and limitations of our method. 1.

G. Sohn; I. Dowman

2003-01-01T23:59:59.000Z

249

Thermal Imaging of Single Living Cells Using Semiconductor Quantum Dots  

E-Print Network (OSTI)

properties of colloidal CdSe/ZnS core/shell quantum dotsstrongly luminescing ZnS-Capped CdSe nanocrystals," JournalPhotochemical instability of CdSe nanocrystals coated by

Yang, Jui-Ming

2009-01-01T23:59:59.000Z

250

Solar thermal financing guidebook  

DOE Green Energy (OSTI)

This guidebook contains information on alternative financing methods that could be used to develop solar thermal systems. The financing arrangements discussed include several lease alternatives, joint venture financing, R and D partnerships, industrial revenue bonds, and ordinary sales. In many situations, alternative financing arrangements can significantly enhance the economic attractiveness of solar thermal investments by providing a means to efficiently allocate elements of risk, return on investment, required capital investment, and tax benefits. A net present value approach is an appropriate method that can be used to investigate the economic attractiveness of alternative financing methods. Although other methods are applicable, the net present value approach has advantages of accounting for the time value of money, yielding a single valued solution to the financial analysis, focusing attention on the opportunity cost of capital, and being a commonly understood concept that is relatively simple to apply. A personal computer model for quickly assessing the present value of investments in solar thermal plants with alternative financing methods is presented in this guidebook. General types of financing arrangements that may be desirable for an individual can be chosen based on an assessment of his goals in investing in solar thermal systems and knowledge of the individual's tax situation. Once general financing arrangements have been selected, a screening analysis can quickly determine if the solar investment is worthy of detailed study.

Williams, T.A.; Cole, R.J.; Brown, D.R.; Dirks, J.A.; Edelhertz, H.; Holmlund, I.; Malhotra, S.; Smith, S.A.; Sommers, P.; Willke, T.L.

1983-05-01T23:59:59.000Z

251

Thermal Reactor Safety  

Science Conference Proceedings (OSTI)

Information is presented concerning fire risk and protection; transient thermal-hydraulic analysis and experiments; class 9 accidents and containment; diagnostics and in-service inspection; risk and cost comparison of alternative electric energy sources; fuel behavior and experiments on core cooling in LOCAs; reactor event reporting analysis; equipment qualification; post facts analysis of the TMI-2 accident; and computational methods.

Not Available

1980-06-01T23:59:59.000Z

252

Thermal barrier coating  

SciTech Connect

A thermal barrier coating for hot gas path components of a combustion turbine based on a zirconia-scandia system. A layer of zirconium scandate having the hexagonal Zr.sub.3 Sc.sub.4 O.sub.12 structure is formed directly on a superalloy substrate or on a bond coat formed on the substrate.

Bowker, Jeffrey Charles (Gibsonia, PA); Sabol, Stephen M. (Orlando, FL); Goedjen, John G. (Oviedo, FL)

2001-01-01T23:59:59.000Z

253

Cylindrical thermal contact conductance  

E-Print Network (OSTI)

Thermal contact conductance is highly important in a wide variety of applications, from the cooling of electronic chips to the thermal management of spacecraft. The demand for increased efficiency means that components need to withstand higher temperatures and heat transfer rates. Many situations call for contact heat transfer through nominally cylindrical interfaces, yet relatively few studies of contact conductance through cylindrical interfaces have been undertaken. This study presents a review of the experimental and theoretical investigations of the heat transfer characteristics of composite cylinders, presenting data available in open literature in comparison with relevant correlations. The present investigation presents a study of the thermal contact conductance of cylindrical interfaces. The experimental investigation of sixteen different material combinations offers an opportunity to develop predictive correlations of the contact conductance, in conjunction with an analysis of the interface pressure as a function of the thermal state of the individual cylindrical shells. Experimental results of the present study are compared with previously published conductance data and conductance models.

Ayers, George Harold

2003-08-01T23:59:59.000Z

254

Preliminary requirements for thermal storage subsystems in solar thermal applications  

DOE Green Energy (OSTI)

Methodologies for the analysis of value and comparing thermal storage concepts are presented. Value is a measure of worth and is determined by the cost of conventional fuel systems. Value data for thermal storage in large solar thermal electric power applications are presented. Thermal storage concepts must be compared when all are performing the same mission. A method for doing that analysis, called the ranking index, is derived. Necessary data to use the methodology are included.

Copeland, R.J.

1980-04-01T23:59:59.000Z

255

Striping in the Suomi NPP VIIRS Thermal Bands through Anisotropic Surface Reflection  

Science Conference Proceedings (OSTI)

We have analyzed the Visible Infrared Imaging Radiometer Suite (VIIRS) thermal emissive band (TEB) M12 images centered at 3.7 ?m and found an unexpected striping. The striping was seen from ascending orbit (day time) over uniform oceans and has a ...

Quanhua Liu; Changyong Cao; Fuzhong Weng

256

National Solar Thermal Test Facility  

SciTech Connect

This is a brief report about a Sandia National Laboratory facility which can provide high-thermal flux for simulation of nuclear thermal flash, measurements of the effects of aerodynamic heating on radar transmission, etc

Cameron, C.P.

1989-12-31T23:59:59.000Z

257

THERMAL INSULATION MATERIALS TEST METHOD ...  

Science Conference Proceedings (OSTI)

... _____ 01/W01 CAN/CGSB-51.2-M88 Thermal Insulation, Calcium Silicate, for Piping, Machinery and Boilers _____ ...

2012-05-22T23:59:59.000Z

258

Liquid metal thermal electric converter  

DOE Patents (OSTI)

A liquid metal thermal electric converter which converts heat energy to electrical energy. The design of the liquid metal thermal electric converter incorporates a unique configuration which directs the metal fluid pressure to the outside of the tube which results in the structural loads in the tube to be compressive. A liquid metal thermal electric converter refluxing boiler with series connection of tubes and a multiple cell liquid metal thermal electric converter are also provided.

Abbin, Joseph P. (Albuquerque, NM); Andraka, Charles E. (Albuquerque, NM); Lukens, Laurance L. (Albuquerque, NM); Moreno, James B. (Albuquerque, NM)

1989-01-01T23:59:59.000Z

259

NVLAP Thermal Insulation Materials LAP  

Science Conference Proceedings (OSTI)

... for thermal insulation materials. The final report for Round 31 was released in February 2010. Proficiency testing is on hold ...

2013-07-18T23:59:59.000Z

260

AQUIFER THERMAL ENERGY STORAGE-A SURVEY  

E-Print Network (OSTI)

High temperature underground thermal energy storage, inProceedings, Thermal Energy Storage in Aquifers Workshop:underground thermal energy storage, in ATES newsletter:

Tsang, Chin Fu

2012-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "imaging multispectral thermal" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Thermal Transport in Graphene Multilayers and Nanoribbons  

E-Print Network (OSTI)

1 CHAPTER 2 Thermal transport atvalues of graphenes thermal conductivity and different1 Thermal conductivity : metals and non - metallic

Subrina, Samia

2011-01-01T23:59:59.000Z

262

Modeling thermal comfort in stratified environments  

E-Print Network (OSTI)

Arens E. , and Wang D. 2004. "Thermal sensation and comfortin transient non-uniform thermal environments", European7730, 1994, Moderate Thermal Environments Determination of

Zhang, H.; Huizenga, C.; Arens, Edward A; Yu, T.

2005-01-01T23:59:59.000Z

263

Thermal Conduction in Graphene and Graphene Multilayers  

E-Print Network (OSTI)

1 1.2 Thermal transport atxv Introduction xii 1.1 Thermal conductivity and65 4.13 Thermal conductivity of graphene as a function of

Ghosh, Suchismita

2009-01-01T23:59:59.000Z

264

Indoor Thermal Comfort, an Evolutionary Biology Perspective  

E-Print Network (OSTI)

ASHRAE Standard 55-2004: Thermal environmental conditionsA behavioural approach to thermal comfort assessment inBerger, X. , 1998. Human thermal comfort at Nimes in summer

Stoops, John L.

2006-01-01T23:59:59.000Z

265

AQUIFER THERMAL ENERGY STORAGE-A SURVEY  

E-Print Network (OSTI)

1978, High temperature underground thermal energy storage,in Proceedings, Thermal Energy Storage in Aquifers Workshop:High temperature underground thermal energy storage, in ATES

Tsang, Chin Fu

2012-01-01T23:59:59.000Z

266

THERMAL ENERGY STORAGE IN AQUIFERS WORKSHOP  

E-Print Network (OSTI)

B. Quale. Seasonal storage of thermal energy in water in theand J. Schwarz, Survey of Thermal Energy Storage in AquifersSecond Annual Thermal Energy Storage Contractors'

Authors, Various

2011-01-01T23:59:59.000Z

267

Holographic Thermal Helicity  

E-Print Network (OSTI)

We study the thermal helicity, defined in arXiv:1211.3850, of a conformal field theory with anomalies in the context of AdS$_{2n+1}$/CFT$_{2n}$. To do so, we consider large charged rotating AdS black holes in the Einstein-Maxwell-Chern-Simons theory with a negative cosmological constant using fluid/gravity expansion. We compute the anomaly-induced current and stress tensor of the dual CFT in leading order of the fluid/gravity derivative expansion and show their agreement with the field theoretical replacement rule for the thermal helicity. Such replacement rule is reflected in the bulk by new replacement rules obeyed by the Hall currents around the black hole.

Tatsuo Azeyanagi; R. Loganayagam; Gim Seng Ng; Maria J. Rodriguez

2013-11-12T23:59:59.000Z

268

Reactor Thermal-Hydraulics  

NLE Websites -- All DOE Office Websites (Extended Search)

Thermal-Hydraulics Thermal-Hydraulics Dr. Tanju Sofu, Argonne National Laboratory In a power reactor, the energy produced in fission reaction manifests itself as heat to be removed by a coolant and utilized in a thermodynamic energy conversion cycle to produce electricity. A simplified schematic of a typical nuclear power plant is shown in the diagram below. Primary coolant loop Steam Reactor Heat exchanger Primary pump Secondary pump Condenser Turbine Water Although this process is essentially the same as in any other steam plant configuration, the power density in a nuclear reactor core is typically four orders of magnitude higher than a fossil fueled plant and therefore it poses significant heat transfer challenges. Maximum power that can be obtained from a nuclear reactor is often limited by the

269

Thermally stable diamond brazing  

DOE Patents (OSTI)

A cutting element and a method for forming a cutting element is described and shown. The cutting element includes a substrate, a TSP diamond layer, a metal interlayer between the substrate and the diamond layer, and a braze joint securing the diamond layer to the substrate. The thickness of the metal interlayer is determined according to a formula. The formula takes into account the thickness and modulus of elasticity of the metal interlayer and the thickness of the TSP diamond. This prevents the use of a too thin or too thick metal interlayer. A metal interlayer that is too thin is not capable of absorbing enough energy to prevent the TSP diamond from fracturing. A metal interlayer that is too thick may allow the TSP diamond to fracture by reason of bending stress. A coating may be provided between the TSP diamond layer and the metal interlayer. This coating serves as a thermal barrier and to control residual thermal stress.

Radtke, Robert P. (Kingwood, TX)

2009-02-10T23:59:59.000Z

270

Thermal spallation drilling  

DOE Green Energy (OSTI)

Thermal spallation drilling is an underdeveloped process with great potential for reducing the costs of drilling holes and mining shafts and tunnels in most very hard rocks. Industry has used this process to drill blast holes for emplacing explosives and to quarry granite. Some theoretical work has been performed, and many signs point to a great future for this process. The Los Alamos National Laboratory has studied the theory of the spallation process and is conducting experiments to prove out the system and to adapt it for use with a conventional rotary rig. This report describes work that has been accomplished at the Laboratory on the development of thermal spallation drilling and some work that is projected for the future on the system. 3 references, 3 figures.

Williams, R.E.

1985-01-01T23:59:59.000Z

271

Solar thermal power  

DOE Green Energy (OSTI)

Solar thermal power is produced by three types of concentrating systems, which utilize parabolic troughs, dishes, and heliostats as the solar concentrators. These systems are at various levels of development and commercialization in the United States and in Europe. The U.S. Industry is currently developing these systems for export at the end of this century and at the beginning of the next one for remote power, village electrification, and grid-connected power. U.S. utilities are not forecasting to need power generation capacity until the middle of the first decade of the 21{sup st} century. At that time, solar thermal electric power systems should be cost competitive with conventional power generation in some unique U.S. markets. In this paper, the authors describe the current status of the development of trough electric, dish/engine, and power tower solar generation systems. 46 refs., 20 figs., 8 tabs.

Mancini, T.R.; Kolb, G.J.; Prairie, M.R. [Sandia National Labs., Albuquerque, NM (United States)

1997-12-31T23:59:59.000Z

272

Thermal Stabilization Blend Plan  

SciTech Connect

This Blend Plan documents the feed material items that are stored in 2736-2 vaults, the 2736-ZB 638 cage, the 192C vault, and the 225 vault that will be processed through the thermal stabilization furnaces. The purpose of thermal stabilization is to heat the material to 1000 degrees Celsius to drive off all water and leave the plutonium and/or uranium as oxides. The stabilized material will be sampled to determine the Loss On Ignition (LOI) or percent water. The stabilized material must meet water content or LOI of less than 0.5% to be acceptable for storage under DOE-STD-3013-99 specifications. Out of specification material will be recycled through the furnaces until the water or LOI limits are met.

RISENMAY, H.R.

2000-05-02T23:59:59.000Z

273

Concentrating Solar Thermal Technology  

Science Conference Proceedings (OSTI)

After nearly 20 years of commercial dormancy, concentrating solar thermal (CST) power development and investment activity is heating up globally. Encouraged by volatile energy prices, carbon markets, and renewable-friendly policies, an increasing number of established companies, newcomers, utilities, and government agencies are planning to deploy CST systems to tap the technologies' improving conversion efficiencies and low-cost electricity production potential. This renewable energy technology perspecti...

2009-03-27T23:59:59.000Z

274

THERMAL NEUTRONIC REACTOR  

DOE Patents (OSTI)

A novel thermal reactor was designed in which a first reflector formed from a high atomic weight, nonmoderating material is disposed immediately adjacent to the reactor core. A second reflector composed of a moderating material is disposed outwardly of the first reflector. The advantage of this novel reflector arrangement is that the first reflector provides a high slow neutron flux in the second reflector, where irradiation experiments may be conducted with a small effect on reactor reactivity.

Spinrad, B.I.

1960-01-12T23:59:59.000Z

275

Thermal reactor safety  

SciTech Connect

Information is presented concerning new trends in licensing; seismic considerations and system structural behavior; TMI-2 risk assessment and thermal hydraulics; statistical assessment of potential accidents and verification of computational methods; issues with respect to improved safety; human factors in nuclear power plant operation; diagnostics and activities in support of recovery; LOCA transient analysis; unresolved safety issues and other safety considerations; and fission product transport.

1980-06-01T23:59:59.000Z

276

Thermally actuated thermionic switch  

DOE Patents (OSTI)

A thermally actuated thermionic switch which responds to an increase of temperature by changing from a high impedance to a low impedance at a predictable temperature set point. The switch has a bistable operation mode switching only on temperature increases. The thermionic material may be a metal which is liquid at the desired operation temperature and held in matrix in a graphite block reservoir, and which changes state (ionizes, for example) so as to be electrically conductive at a desired temperature.

Barrus, D.M.; Shires, C.D.

1982-09-30T23:59:59.000Z

277

Mobile Window Thermal Test  

NLE Websites -- All DOE Office Websites (Extended Search)

Mobile Window Thermal Test (MoWiTT) Facility Mobile Window Thermal Test (MoWiTT) Facility winter.jpg (469135 bytes) The window has come a long way since the days when it was a single pane of glass in a wood frame. Low-emissivity windows were designed to help buildings retain some of the energy that would have leaked out of less efficient windows. Designing efficient window-and-frame systems is one strategy for reducing the energy use of buildings. But the net energy flowing through a window is a combination of temperature- driven thermal flows and transmission of incident solar energy, both of which vary with time. U-factor and solar heat gain coefficient (SHGC), the window properties that control these flows, depend partly on ambient conditions. Window energy flows can affect how much energy a building uses, depending on when the window flows are available to help meet other energy demands within the building, and when they are adverse, adding to building energy use. This leads to a second strategy for reducing building energy use: using the beneficial solar gain available through a window, either for winter heating or for daylighting, while minimizing adverse flows.

278

DIRECT MEASUREMENT OF HEAT FLUX FROM COOLING LAKE THERMAL IMAGERY  

SciTech Connect

Laboratory experiments show a linear relationship between the total heat flux from a water surface to air and the standard deviation of the surface temperature field, {sigma}, derived from thermal images of the water surface over a range of heat fluxes from 400 to 1800 Wm{sup -2}. Thermal imagery and surface data were collected at two power plant cooling lakes to determine if the laboratory relationship between heat flux and {sigma} exists in large heated bodies of water. The heat fluxes computed from the cooling lake data range from 200 to 1400 Wm{sup -2}. The linear relationship between {sigma} and Q is evident in the cooling lake data, but it is necessary to apply band pass filtering to the thermal imagery to remove camera artifacts and non-convective thermal gradients. The correlation between {sigma} and Q is improved if a correction to the measured {sigma} is made that accounts for wind speed effects on the thermal convection. Based on more than a thousand cooling lake images, the correlation coefficients between {sigma} and Q ranged from about 0.8 to 0.9.

Garrett, A; Eliel Villa-Aleman, E; Robert Kurzeja, R; Malcolm Pendergast, M; Timothy Brown, T; Saleem Salaymeh, S

2007-12-19T23:59:59.000Z

279

Evaluation of a Satellite Multispectral VISIR Daytime Statistical Rain-Rate Classifier and Comparison with Passive Microwave Rainfall Estimates  

Science Conference Proceedings (OSTI)

A daytime surface rain-rate classifier, based on artificial neural networks (ANNs), is proposed for the Spinning Enhanced Visible and Infrared Imager (SEVIRI) on board the Meteosat-8 geostationary satellite. It is developed over the British Isles ...

Davide Capacci; Federico Porc

2009-02-01T23:59:59.000Z

280

CALIFORNIA SOLAR INITIATIVE-THERMAL PROGRAMHANDBOOK  

E-Print Network (OSTI)

CALIFORNIA SOLAR INITIATIVE-THERMAL PROGRAMHANDBOOK CALIFORNIA PUBLIC UTILITIES California Solar Initiative Thermal Program Handbook i 1. Introduction to CSI-Thermal Program...........................................................................................................................11 #12;Table of Contents California Solar Initiative Thermal Program Handbook ii 2.5 Surface

Note: This page contains sample records for the topic "imaging multispectral thermal" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Thermal and non-thermal energies in solar flares  

E-Print Network (OSTI)

The energy of the thermal flare plasma and the kinetic energy of the non-thermal electrons in 14 hard X-ray peaks from 9 medium-sized solar flares have been determined from RHESSI observations. The emissions have been carefully separated in the spectrum. The turnover or cutoff in the low-energy distribution of electrons has been studied by simulation and fitting, yielding a reliable lower limit to the non-thermal energy. It remains the largest contribution to the error budget. Other effects, such as albedo, non-uniform target ionization, hot target, and cross-sections on the spectrum have been studied. The errors of the thermal energy are about equally as large. They are due to the estimate of the flare volume, the assumption of the filling factor, and energy losses. Within a flare, the non-thermal/thermal ratio increases with accumulation time, as expected from loss of thermal energy due to radiative cooling or heat conduction. Our analysis suggests that the thermal and non-thermal energies are of the same magnitude. This surprising result may be interpreted by an efficient conversion of non-thermal energy to hot flare plasma.

Pascal Saint-Hilaire; Arnold O. Benz

2005-03-03T23:59:59.000Z

282

FM DANTE fast imaging and variations: emerging rf-based ultrafast imaging techniques  

Science Conference Proceedings (OSTI)

Keywords: DANTE fast imaging, NMR, burst imaging, fast chemical shift imaging, fast imaging, fast spectroscopic imaging, fast susceptibility imaging

Z. H. Cho; Y. M. Ro; I. K. Hong

1998-01-01T23:59:59.000Z

283

Thermal transient anemometer  

DOE Patents (OSTI)

A thermal transient anemometer is disclosed having a thermocouple probe which is utilized to measure the change in temperature over a period of time to provide a measure of fluid flow velocity. The thermocouple probe is located in the fluid flow path and pulsed to heat or cool the probe. The cooling of the heated probe or the heating of the cooled probe from the fluid flow over a period of time is measured to determine the fluid flow velocity. The probe is desired to be locally heated near the tip to increase the efficiency of devices incorporating the probe. 12 figs.

Bailey, J.L.; Vresk, J.

1989-07-18T23:59:59.000Z

284

Thermal indicator for wells  

DOE Patents (OSTI)

Minute durable plate-like thermal indicators are employed for precision measuring static and dynamic temperatures of well drilling fluids. The indicators are small enough and sufficiently durable to be circulated in the well with drilling fluids during the drilling operation. The indicators include a heat resistant indicating layer, a coacting meltable solid component and a retainer body which serves to unitize each indicator and which may carry permanent indicator identifying indicia. The indicators are recovered from the drilling fluid at ground level by known techniques.

Gaven, Jr., Joseph V. (Oakton, VA); Bak, Chan S. (Newbury Park, CA)

1983-01-01T23:59:59.000Z

285

Manipulation of Thermal Phonons  

E-Print Network (OSTI)

Developing materials that can conduct electricity easily, but block the motion of phonons is necessary in the applications of thermoelectric devices, which can generate electricity from temperature differences. In converse, a key requirement as chips get faster is to obtain better ways to dissipate heat. Controlling heat transfer in these crystalline materials devices such as silicon is important. The heat is actually the motion or vibration of atoms known as phonons. Finding ways to manipulate the behavior of phonons is crucial for both energy applications and the cooling of integrated circuits. A novel class of artificially periodic structured materials phononic crystals might make manipulation of thermal phonons possible. In many fields of physical sciences and engineering, acoustic wave propagation in solids attracts many researchers. Wave propagation phenomena can be analyzed by mathematically solving the acoustic wave equation. However, wave propagation in inhomogeneous media with various geometric structures is too complex to find an exact solution. Hence, the Finite Difference Time Domain method is developed to investigate these complicated problems. In this work, the Finite-Difference Time-Domain formula is derived from acoustic wave equations based on the Taylors expansion. The numerical dispersion and stability problems are analyzed. In addition, the convergence conditions of numerical acoustic wave are stated. Based on the periodicity of phononic crystal, the Blochs theorem is applied to fulfill the periodic boundary condition of the FDTD method. Then a wide-band input signal is used to excite various acoustic waves with different frequencies. In the beginning of the calculation process, the wave vector is chosen and fixed. By means of recording the displacement field and taking the Fourier transformation, we can obtain the eigenmodes from the resonance peaks of the spectrum and draw the dispersion relation curve of acoustic waves. With the large investment in silicon nanofabrication techniques, this makes tungsten/silicon phononic crystal a particularly attractive platform for manipulating thermal phonons. Phononic crystal makes use of the fundamental properties of waves to create band gap over which there can be no propagation of acoustic waves in the crystal. This crystal can be applied to deterministically manipulate the phonon dispersion curve affected by different crystal structures and to modify the phonon thermal conductivity accordingly. We can expect this unique metamaterial is a promising route to creating unprecedented thermal properties for highly-efficient energy harvesting and thermoelectric cooling.

Hsu, Chung-Hao

2013-05-01T23:59:59.000Z

286

Thermal Stabilization Blend Plan  

SciTech Connect

The Blend Plan was written to identify items stored outside of the 213 MBA that will be moved into the MBA for thermal stabilization processing. Product quality oxide items stored in our vaults are found in Appendix A. A table is included in Appendix A which details the isotopic values for the oxide items and calculates the amount of material of any specific run that can be placed in a product can and maintain the 15 watt limit to meet storage vault specifications. This Revision of the Blend Plan adds items of lesser dose rate to lower the exposure of the workers until additional shielding can be added to the gloveboxes.

RISENMAY, H.R.

2000-04-20T23:59:59.000Z

287

Advanced solar thermal technology  

SciTech Connect

The application of dish solar collectors to industrial process heat (IPH) has been reviewed. IPH represents a market for displacement of fossil fuels (10 quads/y). A 10% market penetration would indicate a substantial market for solar thermal systems. Apparently, parabolic dish systems can produce IPH at a lower cost than that of troughs or compound parabolic concentrators, even though dish fabrication costs per unit area are more expensive. Successful tests of point-focusing collectors indicate that these systems can meet the energy requirements for process heat applications. Continued efforts in concentrator and transport technology development are needed. 7 figures.

Leibowitz, L.P.; Hanseth, E.; Liu, T.M.

1982-06-01T23:59:59.000Z

288

Split image optical display  

DOE Patents (OSTI)

A video image is displayed from an optical panel by splitting the image into a plurality of image components, and then projecting the image components through corresponding portions of the panel to collectively form the image. Depth of the display is correspondingly reduced.

Veligdan, James T. (Manorville, NY)

2007-05-29T23:59:59.000Z

289

Remote Sensing of Thermal Radiation from an AircraftAn Analysis and Evaluation of Crop-Freeze Protection Methods  

Science Conference Proceedings (OSTI)

Thermal images from an aircraft-mounted scanner are used to evaluate the effectiveness of crop-freeze protection devices. Data from flights made while using fuel oil heaters, a wind machine and an undercanopy irrigation system are compared. ...

R. A. Sutherland; H. E. Hannah; A. F. Cook; J. D. Martsolf

1981-07-01T23:59:59.000Z

290

Structure determination of thermal-spray materials using synchrotron x-ray microtomography. [Cr[sub 3]C[sub 2]/NiCr thermal-spray coating  

SciTech Connect

The structure of materials prepared using thermal spray methods is difficult to determine using conventional microscopy of porosimetry methods. The difficulties inherent in these approaches can be circumvented using synchrotron computed microtomography(CMT). An example of the use of CMT to produce a high resolution non- destructive image of a thermal-spray coating is Cr[sub 3]C[sub 2]/NiCr is described here to illustrate the power of this technique.

Spanne, P.; Jones, K.W. (Brookhaven National Lab., Upton, NY (United States)); Herman, H. (State Univ. of New York, Stony Brook, NY (United States)); Riggs, W.L. (General Electric Co., Cincinnati, OH (United States). Aircraft Engines)

1991-01-01T23:59:59.000Z

291

Hard thermal effective action in QCD through the thermal operator  

E-Print Network (OSTI)

Through the application of the thermal operator to the zero temperature retarded Green's functions, we derive in a simple way the well known hard thermal effective action in QCD. By relating these functions to forward scattering amplitudes for on-shell particles, this derivation also clarifies the origin of important properties of the hard thermal effective action, such as the manifest Lorentz and gauge invariance of its integrand.

Ashok Das; J. Frenkel

2007-03-08T23:59:59.000Z

292

2 Technology Description: Solar Thermal Parabolic Trough Solar Thermal  

E-Print Network (OSTI)

Parabolic troughs track sun, concentrate incident light onto a centralized, tubular receiver that runs length of each trough Thermal fluid circulates through all receivers in solar field Thermal fluid brought to one or more centralized power production facilities Heat transferred to a steam cycle, drives a steam turbine to generate power Cooled thermal fluid is then recirculated th through h solar fi field ld Wet cooling is common, dry cooling possible

Timothy J. Skone; Risks Of Implementation

2012-01-01T23:59:59.000Z

293

THERMALLY DRIVEN ATMOSPHERIC ESCAPE  

Science Conference Proceedings (OSTI)

Accurately determining the escape rate from a planet's atmosphere is critical for determining its evolution. A large amount of Cassini data is now available for Titan's upper atmosphere and a wealth of data is expected within the next decade on escape from Pluto, Mars, and extra-solar planets. Escape can be driven by upward thermal conduction of energy deposited well below the exobase, as well as by nonthermal processes produced by energy deposited in the exobase region. Recent applications of a model for escape driven by upward thermal conduction, called the slow hydrodynamic escape model, have resulted in surprisingly large loss rates for the atmosphere of Titan, Saturn's largest moon. Based on a molecular kinetic simulation of the exobase region, these rates appear to be orders of magnitude too large. Therefore, the slow hydrodynamic model is evaluated here. It is shown that such a model cannot give a reliable description of the atmospheric temperature profile unless it is coupled to a molecular kinetic description of the exobase region. Therefore, the present escape rates for Titan and Pluto must be re-evaluated using the atmospheric model described here.

Johnson, Robert E., E-mail: rej@virginia.ed [Engineering Physics, Thornton Hall B102, University of Virginia, Charlottesville, VA 22902 (United States); Physics Department, New York University, New York, NY 10003 (United States)

2010-06-20T23:59:59.000Z

294

Thermal and Structural Equilibrium Studies of Organic Thermal ...  

Science Conference Proceedings (OSTI)

These organic materials undergo a solid-solid state phase transition before melting which will store large amounts of thermal energy. The binary system of...

295

Electric Vehicle Battery Thermal Issues and Thermal Management Techniques (Presentation)  

SciTech Connect

This presentation examines the issues concerning thermal management in electric drive vehicles and management techniques for improving the life of a Li-ion battery in an EDV.

Rugh, J. P.; Pesaran, A.; Smith, K.

2013-07-01T23:59:59.000Z

296

Anomaly detection using simulated MTI data cubes derived from HYDICE data  

SciTech Connect

The US Department of Energy is funding the development of the Multi-spectral Thermal Imager (MTI), a satellite-based multi-spectral (MS) thermal imaging sensor scheduled for launch in October 1999. MTI is a research and development (R and D) platform to test the applicability of multispectral and thermal imaging technology for detecting and monitoring signs of proliferation of weapons of mass destruction. During its three-year mission, MTI will periodically record images of participating government, industrial and natural sites in fifteen visible and infrared spectral bands to provide a variety of image data associated with weapons production activities. The MTI satellite will have spatial resolution in the visible bands that is five times better than LANDSAT TM in each dimension and will have five thermal bands. In this work, the authors quantify the separability between specific materials and the natural background by applying Receiver Operating Curve (ROC) analysis to the residual errors from a linear unmixing. The authors apply the ROC analysis to quantify performance of the MTI. They describe the MTI imager and simulate its data by filtering HYDICE hyperspectral imagery both spatially and spectrally and by introducing atmospheric effects corresponding to the MTI satellite altitude. They compare and contrast the individual effects on performance of spectral resolution, spatial resolution, atmospheric corrections, and varying atmospheric conditions.

Moya, M.M.; Taylor, J.G.; Stallard, B.R.; Motomatsu, S.E.

1998-07-01T23:59:59.000Z

297

Thermal Flipping of Interstellar Grains  

E-Print Network (OSTI)

In interstellar dust grains, internal processes dissipate rotational kinetic energy. The dissipation is accompanied by thermal fluctuations, which transfer energy from the vibrational modes to rotation. Together, these processes are known as internal relaxation. For the past several years, internal relaxation has been thought to give rise to thermal flipping, with profound consequences for grain alignment theory. I show that thermal flipping is not possible in the limit that the inertia tensor does not vary with time.

Joseph C. Weingartner

2008-08-27T23:59:59.000Z

298

Radiation imaging technology for nuclear materials safeguards  

SciTech Connect

Gamma-ray and neutron imaging technology is emerging as a useful tool for nuclear materials safeguards. Principal applications include improvement in accuracy for nondestructive assay of heterogeneous material (e.g., residues) and wide-area imaging of nuclear material in facilities (e.g., holdup). Portable gamma cameras with gamma-ray spectroscopy are available commercially and are being applied to holdup measurements. The technology has the potential to significantly reduce effort and exposure in holdup campaigns; and, with imaging, some of the limiting assumptions required for conventional holdup analysis can be relaxed, resulting in a more general analysis. Methods to analyze spectroscopic-imaging data to assay plutonium and uranium in processing equipment are being development. Results of holdup measurements using a commercial, portable gamma-cameras are presented. The authors are also developing fast neutron imaging techniques for NDA, search, and holdup. Fast neutron imaging provides a direct measurement of the source of neutrons and is relatively insensitive to surroundings when compared to thermal or epithermal neutron imaging. The technology is well-suited for in-process inventory measurements and verification of materials in interim storage, for which gamma-ray measurements may be inadequate due to self-shielding. Results of numerical simulations to predict the performance of fast-neutron telescopes for safeguards applications are presented.

Prettyman, T.H.; Russo, P.A.; Cheung, C.C.; Christianson, A.D.; Feldman, W.C.; Gavron, A.

1997-12-01T23:59:59.000Z

299

Actively driven thermal radiation shield  

DOE Patents (OSTI)

A thermal radiation shield for cooled portable gamma-ray spectrometers. The thermal radiation shield is located intermediate the vacuum enclosure and detector enclosure, is actively driven, and is useful in reducing the heat load to mechanical cooler and additionally extends the lifetime of the mechanical cooler. The thermal shield is electrically-powered and is particularly useful for portable solid-state gamma-ray detectors or spectrometers that dramatically reduces the cooling power requirements. For example, the operating shield at 260K (40K below room temperature) will decrease the thermal radiation load to the detector by 50%, which makes possible portable battery operation for a mechanically cooled Ge spectrometer.

Madden, Norman W. (Livermore, CA); Cork, Christopher P. (Pleasant Hill, CA); Becker, John A. (Alameda, CA); Knapp, David A. (Livermore, CA)

2002-01-01T23:59:59.000Z

300

Shock waves in thermal lensing  

E-Print Network (OSTI)

We review experimental investigation on spatial shock waves formed by the self-defocusing action of a laser beam propagation in a disordered thermal nonlinear media.

Gentilini, S; DeRe, E; Conti, C

2013-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "imaging multispectral thermal" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Thermal Barrier Coating Systems II  

Science Conference Proceedings (OSTI)

Oct 26, 2009... on the application requirements and not on substrate physical properties such as thermal expansion rate Esp. within the same class of alloys.

302

Thermal Oxidation of Titanium Wires  

Science Conference Proceedings (OSTI)

Structural and Thermal Study of Al2O3 Produced by Oxidation of Al-Powders Mixed with Corn Starch Study of Silicon Carbide/Silicon Nitride Composite...

303

Enhanced Thermal Conductivity Oxide Fuels  

SciTech Connect

the purpose of this project was to investigate the feasibility of increasing the thermal conductivity of oxide fuels by adding small fractions of a high conductivity solid phase.

Alvin Solomon; Shripad Revankar; J. Kevin McCoy

2006-01-17T23:59:59.000Z

304

Thermally activated miniaturized cooling system.  

E-Print Network (OSTI)

??A comprehensive study of a miniaturized thermally activated cooling system was conducted. This study represents the first work to conceptualize, design, fabricate and successfully test (more)

Determan, Matthew Delos

2008-01-01T23:59:59.000Z

305

Boiler Tube Corrosion Characterization With a Scanning Thermal Line  

E-Print Network (OSTI)

Wall thinning due to corrosion in utility boiler waterwall tubing is a significant operational concern for boiler operators. Historically, conventional ultrasonics has been used for inspection of these tubes. Unfortunately, ultrasonic inspection is very manpower intense and slow. Therefore, thickness measurements are typically taken over a relatively small percentage of the total boiler wall and statistical analysis is used to determine the overall condition of the boiler tubing. Other inspection techniques, such as electromagnetic acoustic transducer (EMAT), have recently been evaluated, however they provide only a qualitative evaluation - identifying areas or spots where corrosion has significantly reduced the wall thickness. NASA Langley Research Center, in cooperation with ThermTech Services, has developed a thermal NDE technique designed to quantitatively measure the wall thickness and thus determine the amount of material thinning present in steel boiler tubing. The technique involves the movement of a thermal line source across the outer surface of the tubing followed by an infrared imager at a fixed distance behind the line source. Quantitative images of the material loss due to corrosion are reconstructed from measurements of the induced surface temperature variations. This paper will present a discussion of the development of the thermal imaging system as well as the techniques used to reconstruct images of flaws. The application of the thermal line source coupled with the analysis technique represents a significant improvement in the inspection speed and accuracy for large structures such as boiler waterwalls. A theoretical basis for the technique will be presented to establish the quantitative nature of the technique. Further, a dynamic calibration system ...

Elliott Cramer National; K. Elliott Cramer; Langley Blvd; Ronald Jacobstein; Thomas Reilly

2001-01-01T23:59:59.000Z

306

Thermal barrier coatings  

DOE Patents (OSTI)

This disclosure addresses the issue of providing a metallic-ceramic overlay coating that potentially serves as an interface or bond coat layer to provide enhanced oxidation resistance to the underlying superalloy substrate via the formation of a diffusion barrier regime within the supporting base material. Furthermore, the metallic-ceramic coating is expected to limit the growth of a continuous thermally grown oxide (TGO) layer that has been primarily considered to be the principal cause for failure of existing TBC systems. Compositional compatibility of the metallic-ceramic with traditional yttria-stabilized zirconia (YSZ) top coats is provided to further limit debond or spallation of the coating during operational use. A metallic-ceramic architecture is disclosed wherein enhanced oxidation resistance is imparted to the surface of nickel-based superalloy or single crystal metal substrate, with simultaneous integration of the yttria stabilized zirconia (YSZ) within the metallic-ceramic overlayer.

Alvin, Mary Anne (Pittsburg, PA)

2010-06-22T23:59:59.000Z

307

Inhomogeneous holographic thermalization  

E-Print Network (OSTI)

The sudden injection of energy in a strongly coupled conformal field theory and its subsequent thermalization can be holographically modeled by a shell falling into anti-de Sitter space and forming a black brane. For a homogeneous shell, Bhattacharyya and Minwalla were able to study this process analytically using a weak field approximation. Motivated by event-by-event fluctuations in heavy ion collisions, we include inhomogeneities in this model, obtaining analytic results in a long wavelength expansion. In the early-time window in which our approximations can be trusted, the resulting evolution matches well with that of a simple free streaming model. Near the end of this time window, we find that the stress tensor approaches that of second-order viscous hydrodynamics. We comment on possible lessons for heavy ion phenomenology.

V. Balasubramanian; A. Bernamonti; J. de Boer; B. Craps; L. Franti; F. Galli; E. Keski-Vakkuri; B. Mller; A. Schfer

2013-07-26T23:59:59.000Z

308

Thermal protection apparatus  

DOE Patents (OSTI)

An apparatus for thermally protecting heat sensitive components of tools. The apparatus comprises a Dewar holding the heat sensitive components. The Dewar has spaced-apart inside walls, an open top end and a bottom end. A plug is located in the top end. The inside wall has portions defining an inside wall aperture located at the bottom of the Dewar and the outside wall has portions defining an outside wall aperture located at the bottom of the Dewar. A bottom connector has inside and outside components. The inside component sealably engages the inside wall aperture and the outside component sealably engages the outside wall aperture. The inside component is operatively connected to the heat sensitive components and to the outside component. The connections can be made with optical fibers or with electrically conducting wires.

Bennett, G.A.; Moore, T.K.

1986-08-20T23:59:59.000Z

309

SUPERFAST THERMALIZATION OF PLASMA  

DOE Patents (OSTI)

A method is given for the superfast thermalization of plasma by shock conversion of the kinetic energy stored in rotating plasma rings or plasmoids colliding at near supersonic speeds in a containment field to heat energy in the resultant confined plasma mass. The method includes means for generating rotating plasmoids at the opposite ends of a Pyrotron or Astron containment field. The plasmoids are magnetically accelerated towards each other into the opposite ends of time containment field. During acceleration of the plasmoids toward the center of the containment field, the intensity of the field is sequentially increased to adiabatically compress the plasmoids and increase the plasma energy. The plasmoids hence collide with a violent shock at the eenter of the containment field, causing the substantial kinetic energy stored in the plasmoids to be converted to heat in the resultant plasma mass. (AEC)

Chang, C.C.

1962-06-12T23:59:59.000Z

310

Underground Coal Thermal Treatment  

Science Conference Proceedings (OSTI)

The long-term objective of this work is to develop a transformational energy production technology by insitu thermal treatment of a coal seam for the production of substitute natural gas (SNG) while leaving much of the coal??s carbon in the ground. This process converts coal to a high-efficiency, low-GHG emitting gas fuel. It holds the potential of providing environmentally acceptable access to previously unusable coal resources. This topical report discusses the development of experimental capabilities, the collection of available data, and the development of simulation tools to obtain process thermo-chemical and geo-thermal parameters in preparation for the eventual demonstration in a coal seam. It also includes experimental and modeling studies of CO{sub 2} sequestration. Efforts focused on: ? Constructing a suite of three different coal pyrolysis reactors. These reactors offer the ability to gather heat transfer, mass transfer and kinetic data during coal pyrolysis under conditions that mimic in situ conditions (Subtask 6.1). ? Studying the operational parameters for various underground thermal treatment processes for oil shale and coal and completing a design matrix analysis for the underground coal thermal treatment (UCTT). This analysis yielded recommendations for terms of targeted coal rank, well orientation, rubblization, presence of oxygen, temperature, pressure, and heating sources (Subtask 6.2). ? Developing capabilities for simulating UCTT, including modifying the geometry as well as the solution algorithm to achieve long simulation times in a rubblized coal bed by resolving the convective channels occurring in the representative domain (Subtask 6.3). ? Studying the reactive behavior of carbon dioxide (CO{sub 2}) with limestone, sandstone, arkose (a more complex sandstone) and peridotite, including mineralogical changes and brine chemistry for the different initial rock compositions (Subtask 6.4). Arkose exhibited the highest tendency of participating in mineral reactions, which can be attributed to the geochemical complexity of its initial mineral assemblage. In experiments with limestone, continuous dissolution was observed with the release of CO{sub 2} gas, indicated by the increasing pressure in the reactor (formation of a gas chamber). This occurred due to the lack of any source of alkali to buffer the solution. Arkose has the geochemical complexity for permanent sequestration of CO{sub 2} as carbonates and is also relatively abundant. The effect of including NH{sub 3} in the injected gas stream was also investigated in this study. Precipitation of calcite and trace amounts of ammonium zeolites was observed. A batch geochemical model was developed using Geochemists Workbench (GWB). Degassing effect in the experiments was corrected using the sliding fugacity model in GWB. Experimental and simulation results were compared and a reasonable agreement between the two was observed.

P. Smith; M. Deo; E. Eddings; A. Sarofim; K. Gueishen; M. Hradisky; K. Kelly; P. Mandalaparty; H. Zhang

2011-10-30T23:59:59.000Z

311

Thermal Stabilization Blend Plan  

SciTech Connect

The Blend Plan was written to identify items stored outside of the 213 MBA that will be moved into the MBA for thermal stabilization processing. Product quality oxide items stored in our vaults are found in Appendix B. A table is included in Appendix B which details the isotopic values for the oxide items and calculates the amount of material of any specific run that can be placed in a product can and maintain the 15 watt limit to meet storage vault specifications. There is no chance of exceeding the 15 watt limit with items starting with the designations ''LAO'' or ''PBO.'' All items starting with the designations ''BO,'' ''BLO,'' and ''DZ0'' are at risk of exceeding the 15 watt specification if the can were to be filled.

RISENMAY, H.R.

1999-08-19T23:59:59.000Z

312

Thermally stabilized heliostat  

DOE Patents (OSTI)

An improvement in a heliostat having a main support structure and pivoting and tilting motors and gears and a mirror module for reflecting solar energy onto a collector, the improvement being characterized by an internal support structure within each mirror module and front and back sheets attached to the internal support structure, the front and back sheets having the same coefficient of thermal expansion such that no curvature is induced by temperature change, and a layer of adhesive adhering the mirror to the front sheet. The adhesive is water repellent and has adequate set strength to support the mirror but has sufficient shear tolerance to permit the differential expansion of the mirror and the front sheet without inducing stresses or currature effect. The adhesive also serves to dampen fluttering of the mirror and to protect the mirror backside against the adverse effects of weather. Also disclosed are specific details of the preferred embodiment.

Anderson, Alfred J. (Littleton, CO)

1983-01-01T23:59:59.000Z

313

Nanoscale thermal transport and the thermal conductance of interfaces  

E-Print Network (OSTI)

absorption depends on temperature of the nanotube · Assume heat capacity is comparable to graphite · Cooling conductance · Pump probe apparatus · Transient absorption ­ Carbon nanotubes and thermal transport at hard optical absorption of nanoparticles and nanotubes in liquid suspensions. ­ Measure the thermal relaxation

Braun, Paul

314

Thermal sensation and comfort in transient non-uniform thermal environments  

E-Print Network (OSTI)

cooling applied cooling removed Thermal Sensation Skincooling = 14C cooling removed Thermal Sensation We measureda hand cooling test Models to predict thermal sensation and

Zhang, Hui; Huizenga, Charlie; Arens, Edward; Wang, Danni

2004-01-01T23:59:59.000Z

315

Thermal sensation and comfort in transient non-uniform thermal environments  

E-Print Network (OSTI)

environments. and evaluating thermal 6.0 References AttiaM, Engel P (1981) Thermal alliesthesial response in man isof vehicle climate with a thermal manikin - the relationship

Zhang, Hui; Huizenga, Charlie; Arens, Edward; Wang, Danni

2004-01-01T23:59:59.000Z

316

Determination of thermal parameters of one-dimensional nanostructures through a thermal transient method  

E-Print Network (OSTI)

of heat capacity and thermal conductivity measurements bythe heat pulse method for thermal transport measurements ofG. Speci?c heat and thermal conductivity measurements on

Arriagada, A.; Yu, E. T.; Bandaru, P. R.

2009-01-01T23:59:59.000Z

317

Phase Change Materials for Thermal Energy Storage in Concentrated Solar Thermal Power Plants  

E-Print Network (OSTI)

STUDY FOR SOLAR THERMAL POWER PLANTS, Ottawa, Ontario: 1999.Concentrated Solar Thermal Power Plants A Thesis submittedConcentrated Solar Thermal Power Plants by Corey Lee Hardin

Hardin, Corey Lee

2011-01-01T23:59:59.000Z

318

Phase Change Materials for Thermal Energy Storage in Concentrated Solar Thermal Power Plants  

E-Print Network (OSTI)

PHASE CHANGE THERMAL ENERGY STORAGE FOR CONCENTRATING SOLARChange Materials for Thermal Energy Storage in ConcentratedChange Materials for Thermal Energy Storage in Concentrated

Hardin, Corey Lee

2011-01-01T23:59:59.000Z

319

Phase Change Materials for Thermal Energy Storage in Concentrated Solar Thermal Power Plants  

E-Print Network (OSTI)

PHASE CHANGE THERMAL ENERGY STORAGE FOR CONCENTRATING SOLARMaterials for Thermal Energy Storage in Concentrated SolarMaterials for Thermal Energy Storage in Concentrated Solar

Hardin, Corey Lee

2011-01-01T23:59:59.000Z

320

Peg supported thermal insulation panel  

DOE Patents (OSTI)

A thermal insulation panel which is lightweight, load bearing, accommodates thermal stress, and has excellent high temperature insulation capability comprising high performance insulation between thin metal walls supported by high density, high strength glass pegs made in compliance with specified conditions of time, temperature and pressure.

Nowobilski, Jeffert J. (Orchard Park, NY); Owens, William J. (Kenmore, NY)

1985-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "imaging multispectral thermal" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Thermal conductivity Measurements of Kaolite  

Science Conference Proceedings (OSTI)

Testing was performed to determine the thermal conductivity of Kaolite 1600, which primarily consists of Portland cement and vermiculite. The material was made by Thermal Ceramics for refractory applications. Its combination of light weight, low density, low cost, and noncombustibility made it an attractive alternative to the materials currently used in ES-2 container for radioactive materials. Mechanical properties and energy absorption tests of the Kaolite have been conducted at the Y-12 complex. Heat transfer is also an important factor for the application of the material. The Kaolite samples are porous and trap moisture after extended storage. Thermal conductivity changes as a function of moisture content below 100 C. Thermal conductivity of the Kaolite at high temperatures (up to 700 C) are not available in the literature. There are no standard thermal conductivity values for Kaolite because each sample is somewhat different. Therefore, it is necessary to measure thermal conductivity of each type of Kaolite. Thermal conductivity measurements will help the modeling and calculation of temperatures of the ES-2 containers. This report focuses on the thermal conductivity testing effort at ORNL.

Wang, H

2003-02-21T23:59:59.000Z

322

Thermal conductivity of aqueous foam  

Science Conference Proceedings (OSTI)

Thermal conductivity plays an important part in the response of aqueous foams used as geothermal drilling fluids. The thermal conductivity of these foams was measured at ambient conditions using the thermal conductivity probe technique. Foam densities studied were from 0.03 to 0.2 g/cm/sup 3/, corresponding to liquid volume fractions of the same magnitude. Microscopy of the foams indicated bubble sizes in the range 50 to 300 ..mu..m for nitrogen foams, and 30 to 150 ..mu..m for helium foams. Bubble shapes were observed to be polyhedral at low foam densities and spherical at the higher densities. The measured conductivity values ranged from 0.05 to 0.12 W/m-K for the foams studied. The predicted behavior in foam conductivity caused by a change in the conductivity of the discontinuous gas phase was observed using nitrogen or helium gas in the foams. Analysis of the probe response data required an interpretation using the full intergral solution to the heat conduction equation, since the thermal capacity of the foam was small relative to the thermal mass of the probe. The measurements of the thermal conductivity of the foams were influenced by experimental effects such as the probe input power, foam drainage, and the orientation of the probe and test cell. For nitrogen foams, the thermal conductivity vs liquid volume fraction was observed to fall between predictions based on the parallel ordering and Russell models for thermal conduction in heterogeneous materials.

Drotning, W.D.; Ortega, A.; Havey, P.E.

1982-05-01T23:59:59.000Z

323

Peg supported thermal insulation panel  

DOE Patents (OSTI)

A thermal insulation panel which is lightweight, load bearing, accommodates thermal stress, and has excellent high temperature insulation capability comprises high performance insulation between thin metal walls supported by high density, high strength glass pegs made in compliance with specified conditions of time, temperature and pressure. 2 figs.

Nowobilski, J.J.; Owens, W.J.

1985-04-30T23:59:59.000Z

324

Solar Thermal Electric Technology: 2009  

Science Conference Proceedings (OSTI)

This report summarizes the status and progress of the solar thermal and concentrating solar power (CSP) industry in 2009. It addresses relevant policies in the United States and internationally, technology status, trends, companies and organizations involved in the field, and modeling activities supported by the Electric Power Research Institute (EPRI) and the Solar Thermal Electric Project (STEP).

2010-06-23T23:59:59.000Z

325

Solar Thermal Electric Technology: 2008  

Science Conference Proceedings (OSTI)

This report summarizes the status and progress of the solar thermal and concentrating solar power (CSP) industry in 2008. It addresses technology status, trends, companies and organizations involved in the field, and modeling activities supported by EPRI and the Solar Thermal Electric Project (STEP).

2009-03-31T23:59:59.000Z

326

Thermal And-Or Near Infrared At Coso Geothermal Area (2009) | Open Energy  

Open Energy Info (EERE)

And-Or Near Infrared At Coso Geothermal Area (2009) And-Or Near Infrared At Coso Geothermal Area (2009) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Thermal And-Or Near Infrared At Coso Geothermal Area (2009) Exploration Activity Details Location Coso Geothermal Area Exploration Technique Thermal And-Or Near Infrared Activity Date 2009 Usefulness useful DOE-funding Unknown Exploration Basis Determine the importance of elevation and temperature inversions using thermal infrared satellite images Notes Examples of nighttime temperature inversions are shown in thermal infrared satellite images collected over the Coso geothermal field in eastern California. Temperature-elevation plots show the normal trend of temperature decrease with elevation, on which temperature inversions appear

327

Mining partially annotated images  

Science Conference Proceedings (OSTI)

In this paper, we study the problem of mining partially annotated images. We first define what the problem of mining partially annotated images is, and argue that in many real-world applications annotated images are typically partially annotated and ... Keywords: image annotation completion and prediction, partially annotated training set, semi-supervised learning

Zhongang Qi; Ming Yang; Zhongfei (Mark) Zhang; Zhengyou Zhang

2011-08-01T23:59:59.000Z

328

Near-field thermal transistor  

E-Print Network (OSTI)

Using a block of three separated solid elements, a thermal source and drain together with a gate made of an insulator-metal transition material exchanging near-field thermal radiation, we introduce a nanoscale analog of a field-effect transistor which is able to control the flow of heat exchanged by evanescent thermal photons between two bodies. By changing the gate temperature around its critical value, the heat flux exchanged between the hot body (source) and the cold body (drain) can be reversibly switched, amplified, and modulated by a tiny action on the gate. Such a device could find important applications in the domain of nanoscale thermal management and it opens up new perspectives concerning the development of contactless thermal circuits intended for information processing using the photon current rather than the electric current.

Ben-Abdallah, Philippe

2013-01-01T23:59:59.000Z

329

HEAVY AND THERMAL OIL RECOVERY PRODUCTION MECHANISMS  

Science Conference Proceedings (OSTI)

This technical progress report describes work performed from July 1 through September, 2003 for the project ''Heavy and Thermal Oil Recovery Production Mechanisms,'' DE-FC26-00BC15311. In this project, a broad spectrum of research is undertaken related to thermal and heavy-oil recovery. The research tools and techniques span from pore-level imaging of multiphase fluid flow to definition of reservoir-scale features through streamline-based history-matching techniques. During this period, work focused on completing project tasks in the area of multiphase flow and rock properties. The area of interest is the production mechanisms of oil from porous media at high temperature. Temperature has a beneficial effect on oil recovery and reduces residual oil saturation. Work continued to delineate how the wettability of reservoir rock shifts from mixed and intermediate wet conditions to more water-wet conditions as temperature increases. One mechanism for the shift toward water-wet conditions is the release of fines coated with oil-wet material from pore walls. New experiments and theory illustrate the role of temperature on fines release.

Anthony R. Kovscek; Louis M. Castanier

2004-03-01T23:59:59.000Z

330

HEAVY AND THERMAL OIL RECOVERY PRODUCTION MECHANISMS  

Science Conference Proceedings (OSTI)

This technical progress report describes work performed from January 1 through March 31, 2003 for the project ''Heavy and Thermal Oil Recovery Production Mechanisms,'' DE-FC26-00BC15311. In this project, a broad spectrum of research is undertaken related to thermal and heavy-oil recovery. The research tools and techniques span from pore-level imaging of multiphase fluid flow to definition of reservoir-scale features through streamline-based history matching techniques. During this period, previous analysis of experimental data regarding multidimensional imbibition to obtain shape factors appropriate for dual-porosity simulation was verified by comparison among analytic, dual-porosity simulation, and fine-grid simulation. We continued to study the mechanisms by which oil is produced from fractured porous media at high pressure and high temperature. Temperature has a beneficial effect on recovery and reduces residual oil saturation. A new experiment was conducted on diatomite core. Significantly, we show that elevated temperature induces fines release in sandstone cores and this behavior may be linked to wettability. Our work in the area of primary production of heavy oil continues with field cores and crude oil. On the topic of reservoir definition, work continued on developing techniques that integrate production history into reservoir models using streamline-based properties.

Anthony R. Kovscek

2003-04-01T23:59:59.000Z

331

HEAVY AND THERMAL OIL RECOVERY PRODUCTION MECHANISMS  

Science Conference Proceedings (OSTI)

This technical progress report describes work performed from October 1 through December 31, 2002 , for the project ''Heavy and Thermal Oil Recovery Production Mechanisms.'' In this project, a broad spectrum of research is undertaken related to thermal and heavy-oil recovery. The research tools and techniques used are varied and span from pore-level imaging of multiphase fluid flow to definition of reservoir-scale features through streamline-based history-matching techniques. During this period, experimental data regarding multidimensional imbibition was analyzed to obtain shape factors appropriate for dual-porosity simulation. It is shown that the usual assumption of constant, time-independent shape factors is incorrect. In other work, we continued to study the mechanisms by which oil is produced from fractured media at high pressure and high temperature. High temperature significantly increased the apparent wettability and affected water relative permeability of cores used in previous experiments. A phenomenological and mechanistic cause for this behavior is sought. Our work in the area of primary production of heavy oil continues with field cores and crude oil. On the topic of reservoir definition, work continued on developing techniques that integrate production history into reservoir models using streamline-based properties.

Anthony R. Kovscek

2003-01-01T23:59:59.000Z

332

Seismic Imaging and Monitoring  

SciTech Connect

I give an overview of LANL's capability in seismic imaging and monitoring. I present some seismic imaging and monitoring results, including imaging of complex structures, subsalt imaging of Gulf of Mexico, fault/fracture zone imaging for geothermal exploration at the Jemez pueblo, time-lapse imaging of a walkway vertical seismic profiling data for monitoring CO{sub 2} inject at SACROC, and microseismic event locations for monitoring CO{sub 2} injection at Aneth. These examples demonstrate LANL's high-resolution and high-fidelity seismic imaging and monitoring capabilities.

Huang, Lianjie [Los Alamos National Laboratory

2012-07-09T23:59:59.000Z

333

Seismic Imaging and Monitoring  

SciTech Connect

I give an overview of LANL's capability in seismic imaging and monitoring. I present some seismic imaging and monitoring results, including imaging of complex structures, subsalt imaging of Gulf of Mexico, fault/fracture zone imaging for geothermal exploration at the Jemez pueblo, time-lapse imaging of a walkway vertical seismic profiling data for monitoring CO{sub 2} inject at SACROC, and microseismic event locations for monitoring CO{sub 2} injection at Aneth. These examples demonstrate LANL's high-resolution and high-fidelity seismic imaging and monitoring capabilities.

Huang, Lianjie [Los Alamos National Laboratory

2012-07-09T23:59:59.000Z

334

Manhattan Project: Trinity Images  

Office of Scientific and Technical Information (OSTI)

IMAGES IMAGES Trinity Test Site (July 16, 1945) Resources > Photo Gallery The first 0.11 seconds of the Nuclear Age These seven photographs of the Trinity test were taken by time-lapse cameras. The last is 109 milliseconds, or 0.109 seconds, after detonation. Scroll down to view each individual image. The photographs are courtesy the Los Alamos National Laboratory, via the Federation of American Scientists web site. The animation is original to the Office of History and Heritage Resources. The dawn of the Nuclear Age (Trinity image #1) The dawn of the Nuclear Age Trinity image #2 Trinity image #3 Trinity image #4 Trinity image #5 Trinity, 0.09 seconds after detonation (Trinity image #6) Trinity, 0.09 seconds after detonation Trinity, 0.11 seconds after detonation (Trinity image #7)

335

Web accessible image similarity measurements  

Science Conference Proceedings (OSTI)

Web accessible image similarity measurements. Background: There ... messages). Web Access to Image Similarity Measurements. ...

2013-04-16T23:59:59.000Z

336

Structure determination of thermal-spray materials using synchrotron x-ray microtomography  

SciTech Connect

The structure of materials prepared using thermal spray methods is difficult to determine using conventional microscopy of porosimetry methods. The difficulties inherent in these approaches can be circumvented using synchrotron computed microtomography(CMT). An example of the use of CMT to produce a high resolution non- destructive image of a thermal-spray coating is Cr{sub 3}C{sub 2}/NiCr is described here to illustrate the power of this technique.

Spanne, P.; Jones, K.W. [Brookhaven National Lab., Upton, NY (United States); Herman, H. [State Univ. of New York, Stony Brook, NY (United States); Riggs, W.L. [General Electric Co., Cincinnati, OH (United States). Aircraft Engines

1991-12-31T23:59:59.000Z

337

Thermal to electricity conversion using thermal magnetic properties  

DOE Patents (OSTI)

A system for the generation of Electricity from Thermal Energy using the thermal magnetic properties of a Ferromagnetic, Electrically Conductive Material (FECM) in one or more Magnetic Fields. A FECM is exposed to one or more Magnetic Fields. Thermal Energy is applied to a portion of the FECM heating the FECM above its Curie Point. The FECM, now partially paramagnetic, moves under the force of the one or more Magnetic Fields. The movement of the FECM induces an electrical current through the FECM, generating Electricity.

West, Phillip B [Idaho Falls, ID; Svoboda, John [Idaho Falls, ID

2010-04-27T23:59:59.000Z

338

Solar Thermal Demonstration Project  

SciTech Connect

HVAC Retrofit and Energy Efficiency Upgrades at Clark High School, Las Vegas, Nevada The overall objectives of this project are to increase usage of alternative/renewable fuels, create a better and more reliable learning environment for the students, and reduce energy costs. Utilizing the grant resources and local bond revenues, the District proposes to reduce electricity consumption by installing within the existing limited space, one principal energy efficient 100 ton adsorption chiller working in concert with two 500 ton electric chillers. The main heating source will be primarily from low nitrogen oxide (NOX), high efficiency natural gas fired boilers. With the use of this type of chiller, the electric power and cost requirements will be greatly reduced. To provide cooling to the information technology centers and equipment rooms of the school during off-peak hours, the District will install water source heat pumps. In another measure to reduce the cooling requirements at Clark High School, the District will replace single pane glass and metal panels with ??Kalwall?? building panels. An added feature of the ??Kalwall? system is that it will allow for natural day lighting in the student center. This system will significantly reduce thermal heat/cooling loss and control solar heat gain, thus delivering significant savings in heating ventilation and air conditioning (HVAC) costs.

Biesinger, K.; Cuppett, D.; Dyer, D.

2012-01-30T23:59:59.000Z

339

Cesium capsule thermal analysis  

SciTech Connect

Double-walled stainless steel capsules, produced by the Hanford Waste Encapsulation and Storage Facility (WESF), were designed to facilitate storage of radioactive cesium chloride (CsCl). The capsules were later determined to be a useful resource for irradiation facilities (IFs), and are currently being used at several commercial IFs. A capsule at one of these facilities recently failed, resulting in a release of the CsCl. A thermal analysis of a WESF capsule was performed by Pacific Northwest Laboratory (PNL) at the request of Westinghouse Hanford Company. In this analysis, parametric calculations demonstrates the impact that various parameters have on the temperature distribution within a capsule in a commercial irradiation facility. Specifically, the effect of varying the gas gap conductivity, the exterior heat sink temperatures, the exterior heat transfer distribution, the stainless steel emissivity, and the gamma heating rate were addressed. In addition, a calculation was performed to estimate the highest temperatures likely to have been encountered in one of these capsules. 8 refs., 17 figs., 4 tabs.

Eyler, L.L.; Dodge, R.E.

1989-12-01T23:59:59.000Z

340

Thermally activated heat pumps  

SciTech Connect

This article describes research to develop efficient gas-fired heat pumps heat and cool buildings without CFCs. Space heating and cooling use 46% of all energy consumed in US buildings. Air-conditioning is the single leading cause of peak demand for electricity and is a major user of chlorofluorocarbons (CFCs). Advanced energy conversion technology can save 50% of this energy and eliminate CFCs completely. Besides saving energy, advanced systems substantially reduce emissions of carbon dioxide (a greenhouse gas), sulfur dioxide, and nitrogen oxides, which contribute to smog and acid rain. These emissions result from the burning of fossil fuels used to generate electricity. The Office of Building Technologies (OBT) of the US Department of Energy supports private industry`s efforts to improve energy efficiency and increase the use of renewable energy in buildings. To help industry, OBT, through the Oak Ridge National Laboratory, is currently working on thermally activated heat pumps. OBT has selected the following absorption heat pump systems to develop: generator-absorber heat-exchange (GAX) cycle for heating-dominated applications in residential and light commercial buildings; double-condenser-coupled (DCC) cycle for commercial buildings. In addition, OBT is developing computer-aided design software for investigating the absorption cycle.

NONE

1995-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "imaging multispectral thermal" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Image registration method for medical image sequences  

DOE Patents (OSTI)

Image registration of low contrast image sequences is provided. In one aspect, a desired region of an image is automatically segmented and only the desired region is registered. Active contours and adaptive thresholding of intensity or edge information may be used to segment the desired regions. A transform function is defined to register the segmented region, and sub-pixel information may be determined using one or more interpolation methods.

Gee, Timothy F.; Goddard, James S.

2013-03-26T23:59:59.000Z

342

Neutron imaging of alkali metal heat pipes  

Science Conference Proceedings (OSTI)

High-temperature heat pipes are two-phase, capillary driven heat transfer devices capable of passively providing high thermal fluxes. Such a device using a liquid-metal coolant can be used as a solution for successful thermal management on hypersonic flight vehicles. Imaging of the liquid-metal coolant inside will provide valuable information in characterizing the detailed heat and mass transport. Neutron imaging possesses an inherent advantage from the fact that neutrons penetrate the heat pipe metal walls with very little attenuation, but are significantly attenuated by the liquid metal contained inside. Using the BT-2 beam line at the National Institute of Standards and Technology (NIST) in Gaithersburg, Maryland, preliminary efforts have been conducted on a nickel-sodium heat pipe. The contrast between the attenuated beam and the background is calculated to be approximately 3%. This low contrast requires sacrifice in spatial or temporal resolution so efforts have since been concentrated on lithium (Li) which has a substantially larger neutron attenuation cross section. Using the CG-1D beam line at the High Flux Isotope Reactor (HFIR) of Oak Ridge National Laboratory (ORNL) in Oak Ridge, Tennessee, the first neutron images of high-temperature molybdenum (Mo)-Li heat pipes have been achieved. The relatively high neutron cross section of Li allows for the visualization of the Li working fluid inside the heat pipes. The evaporator region of a gravity assisted cylindrical heat pipe prototype 25 cm long was imaged from start-up to steady state operation up to approximately 900 C. In each corner of the square bore inside, the capillary action raises the Li meniscus above the bulk Li pool in the evaporator region. As the operational temperature changes, the meniscus shapes and the bulk meniscus height also changes. Furthermore, a three-dimensional tomographic image is also reconstructed from the total of 128 projection images taken 1.4o apart in which the Li had already cooled and solidified.

Kihm, Ken [University of Tennessee, Knoxville (UTK); Kirchoff, Eric [University of Tennessee, Knoxville (UTK); Golden, Matt [University of Tennessee, Knoxville (UTK); Rosenfeld, J. [Thermacore Inc.; Rawal, S. [Lockheed Martin Space Systems Company; Pratt, D. [United States Air Force Research Laboratory, Wright-Patterson Air Force Base; Bilheux, Hassina Z [ORNL; Walker, Lakeisha MH [ORNL; Voisin, Sophie [ORNL; Hussey, Dan [NIST Center for Neutron Research (NCRN), Gaithersburg, MD

2013-01-01T23:59:59.000Z

343

Advanced nanofabrication of thermal emission devices  

E-Print Network (OSTI)

Nanofabricated thermal emission devices can be used to modify and modulate blackbody thermal radiation. There are many areas in which altering thermal radiation is extremely useful, especially in static power conversion, ...

Hurley, Fergus (Fergus Gerard)

2008-01-01T23:59:59.000Z

344

Ocean Thermal Energy Conversion | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Thermal Energy Conversion Ocean Thermal Energy Conversion August 16, 2013 - 4:22pm Addthis A process called ocean thermal energy conversion (OTEC) uses the heat energy stored in...

345

THERMAL ENERGY STORAGE IN AQUIFERS WORKSHOP  

E-Print Network (OSTI)

and J. Schwarz, Survey of Thermal Energy Storage in AquifersA. 1957. Steady State Free Thermal Convection of Liquid in a1958. An Experiment on Free Thermal Convection of Water in

Authors, Various

2011-01-01T23:59:59.000Z

346

The Development of Thermals from Rest  

Science Conference Proceedings (OSTI)

Conventional techniques for releasing a thermal in laboratory experiments induce enough initial motion to affect seriously the thermal's subsequent evolution. We have invented a mechanism for releasing thermals from very close to a state of rest. ...

Odn Snchez; David J. Raymond; Larry Libersky; Albert G. Petschek

1989-07-01T23:59:59.000Z

347

Reduced Thermal Conductivity of Compacted Silicon Nanowires  

E-Print Network (OSTI)

alpha1=k1/(density1*cp1); %Thermal diffusivity of PMMA B1=Simon R. Phillpot, Nanoscale Thermal Transport, Journal of9] E.T. Swartz, R.O. Pohl, Thermal Boundary Resistance,

Yuen, Taylor S.

348

THERMAL ENERGY STORAGE IN AQUIFERS WORKSHOP  

E-Print Network (OSTI)

solar power plants, thermal power plants(fuel, nuclear),reject heat from thermal power plants can only be re-protection is the thermal electric power plant. Electric

Authors, Various

2011-01-01T23:59:59.000Z

349

Ceramic thermal barrier coating for rapid thermal cycling applications  

DOE Patents (OSTI)

A thermal barrier coating for metal articles subjected to rapid thermal cycling includes a metallic bond coat deposited on the metal article, at least one MCrAlY/ceramic layer deposited on the bond coat, and a ceramic top layer deposited on the MCrAlY/ceramic layer. The M in the MCrAlY material is Fe, Ni, Co, or a mixture of Ni and Co. The ceramic in the MCrAlY/ceramic layer is mullite or Al.sub.2 O.sub.3. The ceramic top layer includes a ceramic with a coefficient of thermal expansion less than about 5.4.times.10.sup.-6 .degree.C.sup.-1 and a thermal conductivity between about 1 J sec.sup.-1 m.sup.-1 .degree.C.sup.-1 and about 1.7 J sec.sup.-1 m.sup.-1 .degree.C.sup.-1.

Scharman, Alan J. (Hebron, CT); Yonushonis, Thomas M. (Columbus, IN)

1994-01-01T23:59:59.000Z

350

Thermal performance of the Brookhaven natural thermal storage house  

DOE Green Energy (OSTI)

In the Brookhaven natural thermal storage house, an energy-efficient envelope, passive solar collectors, and a variety of energy conservation methods are incorporated. The thermal characteristics of the house during the tested heating season are evaluated. Temperature distributions at different zones are displayed, and the effects of extending heating supply ducts only to the main floor and heating return ducts only from the second floor are discussed. The thermal retrievals from the structure and the passive collectors are assessed, and the total conservation and passive solar contributions are outlined. Several correlation factors relating these thermal behaviors are introduced, and their diurnal variations are displayed. Finally, the annual energy requirements, and the average load factors are analyzed and discussed.

Ghaffari, H.T.; Jones, R.F.

1981-01-01T23:59:59.000Z

351

Thermal Conversion Process (TCP) Technology  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Changing World Technologies' Changing World Technologies' Thermal Conversion Process Commercial Demonstration Plant DOE/EA 1506 Weld County, Colorado December 2004 U.S. DEPARTMENT OF ENERGY GOLDEN FIELD OFFICE 1617 Cole Boulevard Golden, Colorado 80401 Thermal Conversion Process (TCP) Technology Commercial Demonstration - Weld County, CO TABLE OF CONTENTS Environmental Assessment Thermal Conversion Process (TCP) Technology Commercial Demonstration Project Weld County, Colorado SUMMARY............................................................................................................................. S-1 1.0 INTRODUCTION.........................................................................................................1-1 1.1. National Environmental Policy Act and Related Procedures...........................1-1

352

Rapid thermal processing by stamping  

DOE Patents (OSTI)

A rapid thermal processing device and methods are provided for thermal processing of samples such as semiconductor wafers. The device has components including a stamp (35) having a stamping surface and a heater or cooler (40) to bring it to a selected processing temperature, a sample holder (20) for holding a sample (10) in position for intimate contact with the stamping surface; and positioning components (25) for moving the stamping surface and the stamp (35) in and away from intimate, substantially non-pressured contact. Methods for using and making such devices are also provided. These devices and methods allow inexpensive, efficient, easily controllable thermal processing.

Stradins, Pauls; Wang, Qi

2013-03-05T23:59:59.000Z

353

REACTOR GROUT THERMAL PROPERTIES  

DOE Green Energy (OSTI)

Savannah River Site has five dormant nuclear production reactors. Long term disposition will require filling some reactor buildings with grout up to ground level. Portland cement based grout will be used to fill the buildings with the exception of some reactor tanks. Some reactor tanks contain significant quantities of aluminum which could react with Portland cement based grout to form hydrogen. Hydrogen production is a safety concern and gas generation could also compromise the structural integrity of the grout pour. Therefore, it was necessary to develop a non-Portland cement grout to fill reactors that contain significant quantities of aluminum. Grouts generate heat when they set, so the potential exists for large temperature increases in a large pour, which could compromise the integrity of the pour. The primary purpose of the testing reported here was to measure heat of hydration, specific heat, thermal conductivity and density of various reactor grouts under consideration so that these properties could be used to model transient heat transfer for different pouring strategies. A secondary purpose was to make qualitative judgments of grout pourability and hardened strength. Some reactor grout formulations were unacceptable because they generated too much heat, or started setting too fast, or required too long to harden or were too weak. The formulation called 102H had the best combination of characteristics. It is a Calcium Alumino-Sulfate grout that contains Ciment Fondu (calcium aluminate cement), Plaster of Paris (calcium sulfate hemihydrate), sand, Class F fly ash, boric acid and small quantities of additives. This composition afforded about ten hours of working time. Heat release began at 12 hours and was complete by 24 hours. The adiabatic temperature rise was 54 C which was within specification. The final product was hard and displayed no visible segregation. The density and maximum particle size were within specification.

Steimke, J.; Qureshi, Z.; Restivo, M.; Guerrero, H.

2011-01-28T23:59:59.000Z

354

IN SEARCH FOR THERMAL ANOMALIES IN THE COSO GEOTHERMAL FIELD (CALIFORNIA)  

Open Energy Info (EERE)

source source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit History Facebook icon Twitter icon » IN SEARCH FOR THERMAL ANOMALIES IN THE COSO GEOTHERMAL FIELD (CALIFORNIA) USING REMOTE SENSING AND FIELD DATA Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Conference Proceedings: IN SEARCH FOR THERMAL ANOMALIES IN THE COSO GEOTHERMAL FIELD (CALIFORNIA) USING REMOTE SENSING AND FIELD DATA Details Activities (2) Areas (1) Regions (0) Abstract: We attempt to identify thermal anomalies using thermal infrared (TIR) data collected over the Coso Geothermal Power Project with the spaceborne ASTER instrument. Our analysis emphasizes corrections for thermal artifacts in the satellite images caused by topography, albedo, and

355

Thermal And-Or Near Infrared At Fish Lake Valley Area (Deymonaz, Et Al.,  

Open Energy Info (EERE)

Thermal And-Or Near Infrared At Fish Lake Valley Area (Deymonaz, Et Al., Thermal And-Or Near Infrared At Fish Lake Valley Area (Deymonaz, Et Al., 2008) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Thermal And-Or Near Infrared At Fish Lake Valley Area (Deymonaz, Et Al., 2008) Exploration Activity Details Location Fish Lake Valley Area Exploration Technique Thermal And-Or Near Infrared Activity Date Usefulness not indicated DOE-funding Unknown Notes For this project, fused imagery was created using ASTER data and USGS Digital Orthophoto Quandrangles (DOQs). The ASTER data have a spatial resolution of 15 m for the visible to infrared and near_infrared bands, and 30 m for shortwave_infrared bands; with a cost of $85.00 per 60 x 60 km image. Thermal anomalies were mapped using ASTER kinetic temperature data

356

A Helicopter-Borne Video Thermal Infrared Survey Of The Rotorua Geothermal  

Open Energy Info (EERE)

Helicopter-Borne Video Thermal Infrared Survey Of The Rotorua Geothermal Helicopter-Borne Video Thermal Infrared Survey Of The Rotorua Geothermal Field Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Journal Article: A Helicopter-Borne Video Thermal Infrared Survey Of The Rotorua Geothermal Field Details Activities (0) Areas (0) Regions (0) Abstract: Delineation and monitoring of surface thermal activity at geothermal development sites and in tourist and urban areas is important for safety, planning, scientific and field management reasons. Because the standard ground-based temperature measurement methods employed for such work are incomplete, expensive and often impractical, we have developed a helicopter-borne video thermal infrared scanner technique to replace them. The imagery obtained is conveniently stored on videotape and powerful image

357

OCEAN THERMAL ENERGY CONVERSION PROGRAMMATIC ENVIRONMENTAL ASSESSMENT  

E-Print Network (OSTI)

Ocean Thermal Energy Conversion (OTEC) Draft Programmaticof ocean thermal energy conversion technology. U.S. Depart~on Ocean TherUial Energy Conversion, June 18, 1979. Ocean

Sands, M.Dale

2013-01-01T23:59:59.000Z

358

Nanosecond time resolved thermal emission measurements during...  

NLE Websites -- All DOE Office Websites (Extended Search)

Nanosecond time resolved thermal emission measurements during pulse excimer laser interaction with materials Title Nanosecond time resolved thermal emission measurements during...

359

Efficient thermal energy distribution in commercial buildings...  

NLE Websites -- All DOE Office Websites (Extended Search)

Efficient thermal energy distribution in commercial buildings -- Final Report Title Efficient thermal energy distribution in commercial buildings -- Final Report Publication Type...

360

Environmental Energy Technologies Division Thermal Field Tests  

NLE Websites -- All DOE Office Websites (Extended Search)

Thermal Field Tests Joseph H. Klems, LBNL DOE PEER Review San Francisco, CA April 20, 1999 Environmental Energy Technologies Division Current Work l Skylight Thermal Performance *...

Note: This page contains sample records for the topic "imaging multispectral thermal" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Definition: Thermal Gradient Holes | Open Energy Information  

Open Energy Info (EERE)

Gradient Holes Jump to: navigation, search Dictionary.png Thermal Gradient Holes "A hole logged by a temperature probe to determine the thermal gradient. Usually involves a hole...

362

Stewart Thermal Ltd | Open Energy Information  

Open Energy Info (EERE)

Stewart Thermal Ltd Jump to: navigation, search Name Stewart Thermal Ltd Place United Kingdom Sector Biomass Product Provides specialist advice in the field of biomass energy....

363

Solar Thermal Electric | Open Energy Information  

Open Energy Info (EERE)

Electric Jump to: navigation, search TODO: Add description List of Solar Thermal Electric Incentives Retrieved from "http:en.openei.orgwindex.php?titleSolarThermalElectric&o...

364

Development of Low Thermal Expansion Superalloys  

Science Conference Proceedings (OSTI)

For heat resistant alloys it is useful to decrease the thermal expansion for improved adherance of low thermal expansion ceramic coatings like silicon nitride,.

365

Solar Thermal Process Heat | Open Energy Information  

Open Energy Info (EERE)

Process Heat Jump to: navigation, search TODO: Add description List of Solar Thermal Process Heat Incentives Retrieved from "http:en.openei.orgwindex.php?titleSolarThermalPr...

366

Nextreme Thermal Solutions Inc | Open Energy Information  

Open Energy Info (EERE)

Nextreme Thermal Solutions Inc Jump to: navigation, search Name Nextreme Thermal Solutions Inc Place North Carolina Zip 27709-3981 Product String representation "Manufactures ad...

367

Thermal Transport in Graphene Multilayers and Nanoribbons  

E-Print Network (OSTI)

1 CHAPTER 2 Thermal transport atxix List of Tables Phonon transport regimes Length scaleRIVERSIDE Thermal Transport in Graphene Multilayers and

Subrina, Samia

2011-01-01T23:59:59.000Z

368

Energy Basics: Ocean Thermal Energy Conversion  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Thermal Energy Conversion A process called ocean thermal energy conversion (OTEC) uses the heat energy stored in the Earth's oceans to generate electricity. OTEC works best when...

369

California Solar Initiative - Solar Thermal Program | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Solar Thermal Program California Solar Initiative - Solar Thermal Program Eligibility Commercial Fed. Government Industrial Local Government Low-Income Residential Multi-Family...

370

Electrospun Polymer Nanofiber Composite as Thermal Neutron ...  

Science Conference Proceedings (OSTI)

Lithium-6 isotope has a significant thermal neutron cross-section and produces high energy charged particles on thermal neutron absorption. In this research...

371

Thermal Management of Solar Cells  

E-Print Network (OSTI)

as a source of photovoltaic energy is rapidly increasingphotovoltaic cells under concentrated illumination: a critical review," Solar Energyphotovoltaic/thermal collector, PV/T, and it utilizes both electrical and heat energies

Saadah, Mohammed Ahmed

2013-01-01T23:59:59.000Z

372

Thermal insulation of window glass  

SciTech Connect

The thermal insulation of window glass can be increased by a factor of two using spray-on semiconductive SnO/sub 2/: Sb or IN/sub 2/O/sub 3/: Sn coatings. (auth)

Sievers, A.J.

1973-11-01T23:59:59.000Z

373

Research Article Building Thermal, Lighting,  

NLE Websites -- All DOE Office Websites (Extended Search)

Article Building Thermal, Lighting, and Acoustics Modeling E-mail: yanda@tsinghua.edu.cn A detailed loads comparison of three building energy modeling programs: EnergyPlus, DeST...

374

Thermal Equilibration of Planetary Waves  

Science Conference Proceedings (OSTI)

Equilibration of planetary waves toward free-mode forms, steady solutions of the unforced, undamped equations of motion, is studied in a three-level quasi-geostrophic model on the hemisphere. A thermal mechanism is invoked, parameterized as a ...

John Marshall; Damon W. K. So

1990-04-01T23:59:59.000Z

375

Thermal Mass and Demand Response  

NLE Websites -- All DOE Office Websites (Extended Search)

Thermal Mass and Demand Response Speaker(s): Gregor Henze Phil C. Bomrad Date: November 2, 2011 - 12:00pm Location: 90-4133 Seminar HostPoint of Contact: Janie Page The topic of...

376

Solar thermal electric hybridization issues  

DOE Green Energy (OSTI)

Solar thermal electric systems have an advantage over many other renewable energy technologies because the former use heat as an intermediate energy carrier. This is an advantage as it allows for a relatively simple method of hybridization by using heat from fossil-fuel. Hybridization of solar thermal electric systems is a topic that has recently generated significant interest and controversy and has led to many diverse opinions. This paper discusses many of the issues associated with hybridization of solar thermal electric systems such as what role hybridization should play; how it should be implemented; what are the efficiency, environmental, and cost implications; what solar fraction is appropriate; how hybrid systems compete with solar-only systems; and how hybridization can impact commercialization efforts for solar thermal electric systems.

Williams, T A; Bohn, M S; Price, H W

1994-10-01T23:59:59.000Z

377

Thermal energy storage application areas  

DOE Green Energy (OSTI)

The use of thermal energy storage in the areas of building heating and cooling, recovery of industrial process and waste heat, solar power generation, and off-peak energy storage and load management in electric utilities is reviewed. (TFD)

Not Available

1979-03-01T23:59:59.000Z

378

Lih thermal energy storage device  

DOE Patents (OSTI)

A thermal energy storage device for use in a pulsed power supply to store waste heat produced in a high-power burst operation utilizes lithium hydride as the phase change thermal energy storage material. The device includes an outer container encapsulating the lithium hydride and an inner container supporting a hydrogen sorbing sponge material such as activated carbon. The inner container is in communication with the interior of the outer container to receive hydrogen dissociated from the lithium hydride at elevated temperatures.

Olszewski, Mitchell (Knoxville, TN); Morris, David G. (Knoxville, TN)

1994-01-01T23:59:59.000Z

379

Thermal Batteries for Electric Vehicles  

Science Conference Proceedings (OSTI)

HEATS Project: UT Austin will demonstrate a high-energy density and low-cost thermal storage system that will provide efficient cabin heating and cooling for EVs. Compared to existing HVAC systems powered by electric batteries in EVs, the innovative hot-and-cold thermal batteries-based technology is expected to decrease the manufacturing cost and increase the driving range of next-generation EVs. These thermal batteries can be charged with off-peak electric power together with the electric batteries. Based on innovations in composite materials offering twice the energy density of ice and 10 times the thermal conductivity of water, these thermal batteries are expected to achieve a comparable energy density at 25% of the cost of electric batteries. Moreover, because UT Austins thermal energy storage systems are modular, they may be incorporated into the heating and cooling systems in buildings, providing further energy efficiencies and positively impacting the emissions of current building heating/cooling systems.

None

2011-11-21T23:59:59.000Z

380

Estimation theoretical image restoration  

E-Print Network (OSTI)

In this thesis, we have developed an extensive study to evaluate image restoration from a single image, colored or monochromatic. Using a mixture of Gaussian and Poisson noise process, we derived an objective function to ...

Dolne, Jean J

2008-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "imaging multispectral thermal" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Spectrographic imaging system  

DOE Patents (OSTI)

An imaging system for providing spectrographically resolved images. The system incorporates a one-dimensional spatial encoding mask which enables an image to be projected onto a two-dimensional image detector after spectral dispersion of the image. The dimension of the image which is lost due to spectral dispersion on the two-dimensional detector is recovered through employing a reverse transform based on presenting a multiplicity of different spatial encoding patterns to the image. The system is especially adapted for detecting Raman scattering of monochromatic light transmitted through or reflected from physical samples. Preferably, spatial encoding is achieved through the use of Hadamard mask which selectively transmits or blocks portions of the image from the sample being evaluated.

Morris, Michael D. (Ann Arbor, MI); Treado, Patrick J. (Ann Arbor, MI)

1991-01-01T23:59:59.000Z

382

Synthetic stereoscopic panoramic images  

Science Conference Proceedings (OSTI)

Presented here is a discussion of the techniques required to create stereoscopic panoramic images. Such images allow interactive exploration of 3D environments with stereoscopic depth cues. If projected in a surround display environment they can engage ...

Paul Bourke

2006-10-01T23:59:59.000Z

383

Nuclear Imaging instrumentation  

NLE Websites -- All DOE Office Websites (Extended Search)

Nuclear Imaging instrumentation Advances in gamma-ray detection and imaging have increased the pace of discovery in a broad cross-section of the sciences ranging from nuclear...

384

Turbulent thermal diffusion of aerosols in geophysics and laboratory experiments  

E-Print Network (OSTI)

We discuss a new phenomenon of turbulent thermal diffusion associated with turbulent transport of aerosols in the atmosphere and in laboratory experiments. The essence of this phenomenon is the appearance of a nondiffusive mean flux of particles in the direction of the mean heat flux, which results in the formation of large-scale inhomogeneities in the spatial distribution of aerosols that accumulate in regions of minimum mean temperature of the surrounding fluid. This effect of turbulent thermal diffusion was detected experimentally. In experiments turbulence was generated by two oscillating grids in two directions of the imposed vertical mean temperature gradient. We used Particle Image Velocimetry to determine the turbulent velocity field, and an Image Processing Technique based on an analysis of the intensity of Mie scattering to determine the spatial distribution of aerosols. Analysis of the intensity of laser light Mie scattering by aerosols showed that aerosols accumulate in the vicinity of the minimum mean temperature due to the effect of turbulent thermal diffusion. Geophysical applications of the obtained results are discussed.

A. Eidelman; T. Elperin; N. Kleeorin; A. Krein; I. Rogachevskii; J. Buchholz; G. Gruenefeld

2004-11-11T23:59:59.000Z

385

NIST Image Gallery: Search  

Science Conference Proceedings (OSTI)

... Search Tips - Search index includes image titles, descriptions, other text fields - Searches are case-insensitive - Keyword2 is optional. ...

386

Cell Image Visualization  

Science Conference Proceedings (OSTI)

... Biological cell image analysis projects include methods to measure cell segmentation accuracy and new segmentation methods to track live cells. ...

2011-06-17T23:59:59.000Z

387

Video image position determination  

DOE Patents (OSTI)

An optical beam position controller in which a video camera captures an image of the beam in its video frames, and conveys those images to a processing board which calculates the centroid coordinates for the image. The image coordinates are used by motor controllers and stepper motors to position the beam in a predetermined alignment. In one embodiment, system noise, used in conjunction with Bernoulli trials, yields higher resolution centroid coordinates.

Christensen, Wynn (Los Alamos, NM); Anderson, Forrest L. (Bernalillo, NM); Kortegaard, Birchard L. (Los Alamos, NM)

1991-01-01T23:59:59.000Z

388

Imaging with Scattered Neutrons  

E-Print Network (OSTI)

We describe a novel experimental technique for neutron imaging with scattered neutrons. These scattered neutrons are of interest for condensed matter physics, because they permit to reveal the local distribution of incoherent and coherent scattering within a sample. In contrast to standard attenuation based imaging, scattered neutron imaging distinguishes between the scattering cross section and the total attenuation cross section including absorption. First successful low-noise millimeter-resolution images by scattered neutron radiography and tomography are presented.

H. Ballhausen; H. Abele; R. Gaehler; M. Trapp; A. Van Overberghe

2006-10-30T23:59:59.000Z

389

Thermal spray coatings: New materials, processes and applications; Proceedings of the Second National Conference on Thermal Spray, Long Beach, CA, October 31-November 2, 1984  

SciTech Connect

Thermal-spray-coating techniques and their applications are discussed in reviews and reports of laboratory experiments and industrial experience. Topics explored include the future of thermal spraying, plasma-sprayed bonding coats for plastic substrates, plasma-spray deposition of hollow-particle ceramic powders, volumetric-feed-back powder-feed controllers, metal sprayed coating systems onboard U.S. Navy ships, high-performance plasma-sprayed coatings, and arc-coating technology and equipment. Consideration is given to cavitation-erosion of plasma-sprayed alloys, statistical methods of plasma-spray parameter testing, NDE of surface coatings by photothermal imaging, NDE of thermal-spray-coating bonds, and diamond-wheel grinding of thermal-spray materials.

Longo, F.N.

1985-01-01T23:59:59.000Z

390

Document Imaging | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Document Imaging Document Imaging Employee Services Cafeterias Conferencing and Special Events Copy Services Document Imaging Exchange Visitors Program Facility Operations Food...

391

Advanced Thermal Simulator Testing: Thermal Analysis and Test Results  

SciTech Connect

Work at the NASA Marshall Space Flight Center seeks to develop high fidelity, electrically heated thermal simulators that represent fuel elements in a nuclear reactor design to support non-nuclear testing applicable to the potential development of a space nuclear power or propulsion system. Comparison between the fuel pins and thermal simulators is made at the outer fuel clad surface, which corresponds to the outer sheath surface in the thermal simulator. The thermal simulators that are currently being tested correspond to a liquid metal cooled reactor design that could be applied for Lunar surface power. These simulators are designed to meet the geometric and power requirements of a proposed surface power reactor design, accommodate testing of various axial power profiles, and incorporate imbedded instrumentation. This paper reports the results of thermal simulator analysis and testing in a bare element configuration, which does not incorporate active heat removal, and testing in a water-cooled calorimeter designed to mimic the heat removal that would be experienced in a reactor core.

Bragg-Sitton, Shannon M.; Dickens, Ricky; Dixon, David; Reid, Robert; Adams, Mike; Davis, Joe [NASA Marshall Space Flight Center, Nuclear Systems Branch/ER24, MSFC, AL 35812 (United States)

2008-01-21T23:59:59.000Z

392

Near-Electrode Imager  

DOE Patents (OSTI)

An apparatus, near-electrode imager, for employing nuclear magnetic resonance imaging to provide in situ measurements of electrochemical properties of a sample as a function of distance from a working electrode. The near-electrode imager use the radio frequency field gradient within a cylindrical toroid cavity resonator to provide high-resolution nuclear magnetic resonance spectral information on electrolyte materials.

Rathke, Jerome W.; Klingler, Robert J.; Woelk, Klaus; Gerald, Rex E.,II

1999-05-01T23:59:59.000Z

393

Acoustic Imaging Suite  

INLs acoustic imaging technology improves methods of capturing moving images of a specified object by using a photorefractive effect to produce a full-field image of the object without using a probe to perform a full scan of the object. INL ...

394

Medical imaging systems  

Science Conference Proceedings (OSTI)

A medical imaging system provides simultaneous rendering of visible light and diagnostic or functional images. The system may be portable, and may include adapters for connecting various light sources and cameras in open surgical environments or laparascopic or endoscopic environments. A user interface provides control over the functionality of the integrated imaging system. In one embodiment, the system provides a tool for surgical pathology.

Frangioni, John V

2013-06-25T23:59:59.000Z

395

Diagnostic Imaging Emergency Medicine  

E-Print Network (OSTI)

UC Davis Veterinary Diagnostic Imaging Symposium Emergency Medicine May 15, 2011 Gladys Valley Hall devoted to triage, assessment, and imaging diagnostics in emergency medicine. Speakers in this year's symposium include specialists in diagnostic imaging, and emergency and critical care. Sunday May 15, 2011 8

Hammock, Bruce D.

396

Nonlocal imaging by conditional averaging of random reference measurements  

E-Print Network (OSTI)

We report the nonlocal imaging of an object by conditional averaging of the random exposure frames of a reference detector, which only sees the freely propagating field from a thermal light source. A bucket detector, synchronized with the reference detector, records the intensity fluctuations of an identical beam passing through the object mask. These fluctuations are sorted according to their values relative to the mean, then the reference data in the corresponding time-bins for a given fluctuation range are averaged, to produce either positive or negative images. Since no correlation calculations are involved, this correspondence imaging technique challenges our former interpretations of "ghost" imaging. Compared with conventional correlation imaging or compressed sensing schemes, both the number of exposures and computation time are greatly reduced, while the visibility is much improved. A simple statistical model is presented to explain the phenomenon.

Kai-Hong Luo; Boqiang Huang; Wei-Mou Zheng; Ling-An Wu

2013-03-22T23:59:59.000Z

397

Imaging carrier and phonon transport in Si using ultrashort optical pulses  

DOE Green Energy (OSTI)

A series of experiments have been conducted that microscopically image thermal diffusion and surface acoustic phonon propagation within a single crystallite of a polycrystalline Si sample. The experimental approach employs ultrashort optical pulses to generate an electron-hole plasma and a second probe pulse is used to image the evolution of the plasma. By decomposing the signal into a component that varies with delay time and a steady state component that varies with pump modulation frequency, the respective influence of carrier recombination and thermal diffusion are identified. Additionally, the coherent surface acoustic phonon component to the signal is imaged using a Sagnac interferometer to monitor optical phase.

David H. Hurley; O. B. Wright; O. Matsuda; B. E. McCandless; S. Shinde

2009-01-01T23:59:59.000Z

398

The Nature of Thermal Blackbody Radiation  

E-Print Network (OSTI)

It was shown recently that thermal radio emission has a stimulated character, and it is quite possible that thermal black body radiation in other spectral ranges also has an induced origin. The induced origin of thermal black body emission leads to important astrophysical consequences, such as the existence of laser type sources and thermal harmonics in stellar spectra.

F. V. Prigara

2002-01-11T23:59:59.000Z

399

Thermal storage module for solar dynamic receivers  

DOE Patents (OSTI)

A thermal energy storage system comprising a germanium phase change material and a graphite container.

Beatty, Ronald L. (Farragut, TN); Lauf, Robert J. (Oak Ridge, TN)

1991-01-01T23:59:59.000Z

400

Thermal Modeling of Hybrid Storage Clusters  

Science Conference Proceedings (OSTI)

There is a lack of thermal models for storage clusters; most existing thermal models do not take into account the utilization of hard drives (HDDs) and solid state disks (SSDs). To address this problem, we build a thermal model for hybrid storage clusters ... Keywords: Cluster, Hybrid, Model, Storage, Thermal

Xunfei Jiang; Maen M. Al Assaf; Ji Zhang; Mohammed I. Alghamdi; Xiaojun Ruan; Tausif Muzaffar; Xiao Qin

2013-09-01T23:59:59.000Z

Note: This page contains sample records for the topic "imaging multispectral thermal" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Battery Thermal Management System Design Modeling (Presentation)  

DOE Green Energy (OSTI)

Presents the objectives and motivations for a battery thermal management vehicle system design study.

Kim, G-H.; Pesaran, A.

2006-10-01T23:59:59.000Z

402

Solar thermal power systems. Program summary  

DOE Green Energy (OSTI)

Each of DOE's solar Thermal Power Systems projects funded and/or in existence during FY 1978 is described and the status as of September 30, 1978 is reflected. These projects are divided as follows: small thermal power applications, large thermal power applications, and advanced thermal technology. Also included are: 1978 project summary tables, bibliography, and an alphabetical index of contractors. (MHR)

Not Available

1978-12-01T23:59:59.000Z

403

Device for thermal transfer and power generation  

SciTech Connect

A system is provided. The system includes a device that includes top and bottom thermally conductive substrates positioned opposite to one another, wherein a top surface of the bottom thermally conductive substrate is substantially atomically flat and a thermal blocking layer disposed between the top and bottom thermally conductive substrates. The device also includes top and bottom electrodes separated from one another between the top and bottom thermally conductive substrates to define a tunneling path, wherein the top electrode is disposed on the thermal blocking layer and the bottom electrode is disposed on the bottom thermally conductive substrate.

Weaver, Stanton Earl (Northville, NY); Arik, Mehmet (Niskayuna, NY)

2011-04-19T23:59:59.000Z

404

STATISTICAL ANALYSES ON THERMAL ASPECTS OF SOLAR FLARES  

SciTech Connect

The frequency distribution of flare energies provides a crucial diagnostic to calculate the overall energy residing in flares and to estimate the role of flares in coronal heating. It often takes a power law as its functional form. We have analyzed various variables, including the thermal energies E{sub th} of 1843 flares at their peak time. They were recorded by both Geostationary Operational Environmental Satellites and Reuven Ramaty High-Energy Solar Spectroscopic Imager during the time period from 2002 to 2009 and are classified as flares greater than C 1.0. The relationship between different flare parameters is investigated. It is found that fitting the frequency distribution of E{sub th} to a power law results in an index of -2.38. We also investigate the corrected thermal energy E{sub cth}, which represents the flare total thermal energy including the energy loss in the rising phase. Its corresponding power-law slope is -2.35. Compilation of the frequency distributions of the thermal energies from nanoflares, microflares, and flares in the present work and from other authors shows that power-law indices below -2.0 have covered the range from 10{sup 24} to 10{sup 32} erg. Whether this frequency distribution can provide sufficient energy to coronal heatings in active regions and the quiet Sun is discussed.

Li, Y. P.; Gan, W. Q.; Feng, L., E-mail: wqgan@pmo.ac.cn [Key Laboratory of Dark Matter and Space Astronomy, Purple Mountain Observatory, Chinese Academy of Sciences, 210008 Nanjing (China)

2012-03-10T23:59:59.000Z

405

Second thermal storage applications workshop  

DOE Green Energy (OSTI)

On February 7 and 8, 1980, approximately 20 persons representing the management of both the Solar Thermal Power Systems Program (TPS) of the US Department of Energy (DOE) Division of Central Solar Technology (CST) and the Thermal Energy Storage Program (TES) of the DOE Division of Energy Storage Systems (STOR) met in San Antonio, Texas, for the Second Thermal Storage Applications Workshop. The purpose of the workshop was to review the joint Thermal Energy Storage for Solar Thermal Applications (TESSTA) Program between CST and STOR and to discuss important issues in implementing it. The meeting began with summaries of the seven major elements of the joint program (six receiver-related, storage development elements, and one advanced technology element). Then, a brief description along with supporting data was given of several issues related to the recent joint multiyear program plan (MYPP). Following this session, the participants were divided into three smaller groups representing the program elements that mainly supported large power, small power, and advanced technology activities. During the afternoon of the first day, each group prioritized the program elements through program budgets and discussed the issues defined as well as others of concern. On the morning of the second day, representatives of each group presented the group's results to the other participants. Major conclusions arising from the workshop are presented regarding program and budget. (LEW)

Wyman, C.E.; Larson, R.W.

1980-06-01T23:59:59.000Z

406

SNAP Image Gallery  

NLE Websites -- All DOE Office Websites (Extended Search)

Images Images Cutaway image of SNAP A cutaway illustration of SNAP showing some of the interior optics. Cutaway image of SNAP A computer generated cutaway illustration of SNAP Cutaway image of SNAP's primary mirror A computer generated cutaway illustration of SNAP's primary mirror image of SNAP spacecraft A computer generated illustration of the SNAP spacecraft computer generated image of SNAP A computer generated illustration of SNAP Before-and-after pictures (and Hubble Space Telescope picture) of a high-redshift supernovae discovered by the Supernova Cosmology Project in March, 1998. Before-and-after pictures (and Hubble Space Telescope picture) of a high-redshift supernovae discovered in March, 1998. This observaton showed that the expansion of the universe was accelerarting. Credit: High Redshift Supernova Search Supernova Cosmology Project

407

Shape-based image retrieval applied to trademark images  

Science Conference Proceedings (OSTI)

In this chapter, we propose a new shape-based, query-by-example, image database retrieval method that is able to match a query image to one of the images in the database, based on a whole or partial match. The proposed method has two key components: ... Keywords: image databases, shape analysis, shape representation, shape-based image retrieval, trademark image retrieval

Ossama El Badawy; Mohamed Kamel

2004-01-01T23:59:59.000Z

408

High Performance Thermal Interface Technology Overview  

E-Print Network (OSTI)

An overview on recent developments in thermal interfaces is given with a focus on a novel thermal interface technology that allows the formation of 2-3 times thinner bondlines with strongly improved thermal properties at lower assembly pressures. This is achieved using nested hierarchical surface channels to control the particle stacking with highly particle-filled materials. Reliability testing with thermal cycling has also demonstrated a decrease in thermal resistance after extended times with longer overall lifetime compared to a flat interface.

R. Linderman; T. Brunschwiler; B. Smith; B. Michel

2008-01-07T23:59:59.000Z

409

Analyses of MTI Imagery of Power Plant Thermal Discharge  

Science Conference Proceedings (OSTI)

MTI images of thermal discharge from three power plants are analyzed in this paper with the aid of a 3-D hydrodynamic code. The power plants use different methods to dissipate waste heat in the environment: a cooling lake at Comanche Peak, ocean discharge at Pilgrim and cooling canals at Turkey Point. This paper shows that it is possible to reproduce the temperature distributions captured in MTI imagery with accurate code inputs, but the key parameters change from site to site. Wind direction and speed are the most important parameters at Pilgrim, whereas air temperatures and dewpoint temperatures are most important at Comanche Peak and Turkey Point. This paper also shows how the combination of high-resolution thermal imagery and hydrodynamic simulation lead to better understanding of the mechanisms by which waste heat is dissipated in the environment.

Garrett, A.J.

2001-06-27T23:59:59.000Z

410

OpenEI Community - images  

Open Energy Info (EERE)

Image upload with broken thumbnail image http:en.openei.orgcommunitydiscussionimage-upload-broken-thumbnail-image

OpenEI users can upload images to the wiki by typing a new...

411

Similarity Retrieval of Trademark Images  

Science Conference Proceedings (OSTI)

The Artisan system retrieves abstract trademark images by shape similarity. It analyzes each image to characterize key shape components, grouping image regions into families that potentially mirror human image perception, and then derives characteristic ...

John P. Eakins; Jago M. Boardman; Margaret E. Graham

1998-04-01T23:59:59.000Z

412

Cornell University Thermal Comfort Report  

NLE Websites -- All DOE Office Websites (Extended Search)

Thermal Comfort Thermal Comfort Thermal comfort in the CUSD home is a top priority for our team. Accordingly, we designed a redundant HVAC system that would carefully manage the comfort of our decathletes and guests throughout the competition and the life of the house. The CUSD home's HVAC system was optimized for Washington, DC, with the cold Ithaca climate in mind. Our design tools included a schematic energy-modeling interface called TREAT, which was built off of the SuNREL platform. TREAT was used to passively condition the space. Our schematic energy modeling helped us properly size window areas, overhangs, and building mass distribution. We used a computation fluid dynamics (CFD) package called AirPak, to refine our design. The home was modeled in both

413

solar thermal | OpenEI  

Open Energy Info (EERE)

thermal thermal Dataset Summary Description This dataset presents summary information related to world solar energy. It is part of a supporting dataset for the book World On the Edge: How to Prevent Environmental and Economic Collapse by Lester R. Source Earth Policy Institute Date Released January 12th, 2011 (3 years ago) Date Updated Unknown Keywords EU solar solar PV solar thermal world Data application/vnd.ms-excel icon Excel spreadsheet, summary solar energy data on multiple tabs (xls, 145.9 KiB) Quality Metrics Level of Review Some Review Comment Temporal and Spatial Coverage Frequency Time Period License License Open Data Commons Attribution License Comment "Reuse of our data is permitted. We merely ask that wherever it is listed, it be appropriately cited"

414

Invert Effective Thermal Conductivity Calculation  

SciTech Connect

The objective of this calculation is to evaluate the temperature-dependent effective thermal conductivities of a repository-emplaced invert steel set and surrounding ballast material. The scope of this calculation analyzes a ballast-material thermal conductivity range of 0.10 to 0.70 W/m {center_dot} K, a transverse beam spacing range of 0.75 to 1.50 meters, and beam compositions of A 516 carbon steel and plain carbon steel. Results from this calculation are intended to support calculations that identify waste package and repository thermal characteristics for Site Recommendation (SR). This calculation was developed by Waste Package Department (WPD) under Office of Civilian Radioactive Waste Management (OCRWM) procedure AP-3.12Q, Revision 1, ICN 0, Calculations.

M.J. Anderson; H.M. Wade; T.L. Mitchell

2000-03-17T23:59:59.000Z

415

Thermal And-Or Near Infrared At Socorro Mountain Area (Owens, Et Al., 2005)  

Open Energy Info (EERE)

source source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit History Facebook icon Twitter icon » Thermal And-Or Near Infrared At Socorro Mountain Area (Owens, Et Al., 2005) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Thermal And-Or Near Infrared At Socorro Mountain Area (Owens, Et Al., 2005) Exploration Activity Details Location Socorro Mountain Area Exploration Technique Thermal And-Or Near Infrared Activity Date Usefulness not indicated DOE-funding Unknown Notes IR remote sensing has located elevated surface temperatures (<12 degrees C above background) near Socorro Peak). A four-year compellation of ASTER satellite IR imaging was used. These images work on a 5-band, TIR processor

416

Characterization of energetic devices for thermal battery applications by high-speed photography  

DOE Green Energy (OSTI)

High-speed photography at rates of up to 20,000 images per second was used to measure these properties in thermal battery igniters and also the ignition of thermal battery itself. By synchronizing a copper vapor laser to the high-speed camera, laser-illuminated images recorded details of the performance of a component. Output characteristics of several types of hermetically-sealed igniters using a TiH{chi}/KCIO{sub 4} pyrotechnic blend were measured as a function of the particle size of the pyrotechnic fuel and the closure disc thickness. The igniters were filmed under both ambient (i.e., unconfined) and confined conditions. Recently, the function of the igniter in a cut-away section of a ``mock`` thermal battery has been filmed. Partial details of these films are discussed in this paper, and selected examples of the films will be displayed via video tape during the presentation of the paper.

Dosser, L.R. [EG and G Mound Applied Technologies, Miamisburg, OH (United States); Guidotti, R. [Sandia National Labs., Albuquerque, NM (United States)

1993-12-31T23:59:59.000Z

417

Propagation of Reactions in Thermally-damaged PBX-9501  

SciTech Connect

A thermally-initiated explosion in PBX-9501 (octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine) is observed in situ by flash x-ray imaging, and modeled with the LLNL multi-physics arbitrary-Lagrangian-Eulerian code ALE3D. The containment vessel deformation provides a useful estimate of the reaction pressure at the time of the explosion, which we calculate to be in the range 0.8-1.4 GPa. Closely-coupled ALE3D simulations of these experiments, utilizing the multi-phase convective burn model, provide detailed predictions of the reacted mass fraction and deflagration front acceleration. During the preinitiation heating phase of these experiments, the solid HMX portion of the PBX-9501 undergoes a {beta}-phase to {delta}-phase transition which damages the explosive and induces porosity. The multi-phase convective burn model results demonstrate that damaged particle size and pressure are critical for predicting reaction speed and violence. In the model, energetic parameters are taken from LLNL's thermochemical-kinetics code Cheetah and burn rate parameters from Son et al. (2000). Model predictions of an accelerating deflagration front are in qualitative agreement with the experimental images assuming a mode particle diameter in the range 300-400 {micro}m. There is uncertainty in the initial porosity caused by thermal damage of PBX-9501 and, thus, the effective surface area for burning. To better understand these structures, we employ x-ray computed tomography (XRCT) to examine the microstructure of PBX-9501 before and after thermal damage. Although lack of contrast between grains and binder prevents the determination of full grain size distribution in this material, there are many domains visible in thermally damaged PBX-9501 with diameters in the 300-400 {micro}m range.

Tringe, J W; Glascoe, E A; Kercher, J R; Willey, T M; Springer, H K; Greenwood, D W; Molitoris, J D; Smilowitz, L; Henson, B F; Maienschein, J L

2010-03-05T23:59:59.000Z

418

HEAVY AND THERMAL OIL RECOVERY PRODUCTION MECHANISMS  

SciTech Connect

The Stanford University Petroleum Research Institute (SUPRI-A) studies oil recovery mechanisms relevant to thermal and heavy-oil production. The scope of work is relevant across near-, mid-, and long-term time frames. In August of 2000 we received funding from the U. S. DOE under Award No. DE-FC26-00BC15311 that completed December 1, 2003. The project was cost shared with industry. Heavy oil (10 to 20{sup o} API) is an underutilized energy resource of tremendous potential. Heavy oils are much more viscous than conventional oils. As a result, they are difficult to produce with conventional recovery methods. Heating reduces oil viscosity dramatically. Hence, thermal recovery is especially important because adding heat, usually via steam injection generally improves displacement efficiency. The objectives of this work were to improve our understanding of the production mechanisms of heavy oil under both primary and enhanced modes of operation. The research described spanned a spectrum of topics related to heavy and thermal oil recovery and is categorized into: (1) multiphase flow and rock properties, (2) hot fluid injection, (3) improved primary heavy-oil recovery, (4) in-situ combustion, and (5) reservoir definition. Technology transfer efforts and industrial outreach were also important to project effort. The research tools and techniques used were quite varied. In the area of experiments, we developed a novel apparatus that improved imaging with X-ray computed tomography (CT) and high-pressure micromodels etched with realistic sandstone roughness and pore networks that improved visualization of oil-recovery mechanisms. The CT-compatible apparatus was invaluable for investigating primary heavy-oil production, multiphase flow in fractured and unfractured media, as well as imbibition. Imbibition and the flow of condensed steam are important parts of the thermal recovery process. The high-pressure micromodels were used to develop a conceptual and mechanistic picture of primary heavy-oil production by solution gas drive. They allowed for direct visualization of gas bubble formation, bubble growth, and oil displacement. Companion experiments in representative sands and sandstones were also conducted to understand the mechanisms of cold production. The evolution of in-situ gas and oil saturation was monitored with CT scanning and pressure drop data. These experiments highlighted the importance of depletion rate, overburden pressure, and oil-phase chemistry on the cold production process. From the information provided by the experiments, a conceptual and numerical model was formulated and validated for the heavy-oil solution gas drive recovery process. Also in the area of mechanisms, steamdrive for fractured, low permeability porous media was studied. Field tests have shown that heat injected in the form of steam is effective at unlocking oil from such reservoir media. The research reported here elucidated how the basic mechanisms differ from conventional steamdrive and how these differences are used to an advantage. Using simulations of single and multiple matrix blocks that account for details of heat transfer, capillarity, and fluid exchange between matrix and fracture, the importance of factors such as permeability contrast between matrix and fracture and oil composition were quantified. Experimentally, we examined the speed and extent to which steam injection alters the permeability and wettability of low permeability, siliceous rocks during thermal recovery. Rock dissolution tends to increase permeability moderately aiding in heat delivery, whereas downstream the cooled fluid deposits silica reducing permeability. Permeability reduction is not catastrophic. With respect to wettability, heat shifts rock wettability toward more water wet conditions. This effect is beneficial for the production of heavy and medium gravity oils as it improves displacement efficiency. A combination of analytical and numerical studies was used to examine the efficiency of reservoir heating using nonconventional wells such as horizontal and multi

Anthony R. Kovscek; Louis M. Castanier

2003-12-31T23:59:59.000Z

419

Thermal reclaimer apparatus for a thermal sand reclamation system  

SciTech Connect

A thermal reclaimer apparatus is disclosed for thermally removing from the used foundry sand the organic matter that is present therein. The subject thermal reclaimer apparatus includes chamber means in which the used foundry sand is heated to a predetermined temperature for a preestablished period in order to accomplish the burning away of the organic matter that the used foundry sand contains. The chamber means includes inlet means provided at one end thereof and outlet means provided at the other end thereof. Feed means are cooperatively associated with the pipe means and thereby with the inlet means for feeding the used foundry sand through the inlet means into the chamber means. The subject thermal reclaimer apparatus further includes rotating means operative for effecting the rotation of the chamber means as the used foundry sand is being heated therein. The chamber means has cooperatively associated therewith burner means located at the same end thereof as the outlet means. The burner means is operative to effect the heating of the used foundry sand to the desired temperature within the chamber means. Tumbling means are provided inside the chamber means to ensure that the used foundry sand is constantly turned over, i.e., tumbled, and that the lumps therein are broken up as the chamber means rotates. Lastly, the used foundry sand from which the organic matter has been removed leaves the chamber means through the outlet means.

Deve, V.

1984-02-07T23:59:59.000Z

420

Application of Combined Thermal Equivalen in Thermal Power Plant Reduction  

Science Conference Proceedings (OSTI)

The 3.8MPa medium-pressure steam of Yuntianhua Company get low pressure steam through reducing temperature and pressure, which is used as a heat tracing, a reserve supply of heat. For this situation, the article based on the analysis of energy and chemical ... Keywords: combined thermal equivalent, turbine, economize on energy

Zhang Zhuming; Li Hu; Wang Hua; Qing Shan; Li Liangqing; He Ping; Ma Linzhuan

2011-02-01T23:59:59.000Z

Note: This page contains sample records for the topic "imaging multispectral thermal" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

CPC thermal collector test plan  

DOE Green Energy (OSTI)

A comprehensive set of test procedures has evolved at Argonne National Laboratory for establishing the performance of compound parabolic and related concentrating thermal collectors with large angular fields of view. The procedures range from separate thermal and optical tests, to overall performance tests. A calorimetric ratio technique has been developed to determine the heat output of a collector without knowledge of the heat transfer fluid's mass flow rate and heat capacity. Sepcial attention is paid to the problem of defining and measuring the incident solar flux with respect to which the collector efficiency is to be calculated.

Reed, K A

1977-01-01T23:59:59.000Z

422

Thermal Profiling of Nanoscale Circuitry  

Real-time atomic-resolution imaging of the nano-objects shows how they evolve at temperatures of up to 4,000K, how the atoms of the material shift, ...

423

What can Recycling in Thermal Reactors Accomplish?  

SciTech Connect

Thermal recycle provides several potential benefits when used as stop-gap, mixed, or backup recycling to recycling in fast reactors. These three roles involve a mixture of thermal and fast recycling; fast reactors are required to some degree at some time. Stop-gap uses thermal reactors only until fast reactors are adequately deployed and until any thermal-recycle-only facilities have met their economic lifetime. Mixed uses thermal and fast reactors symbiotically for an extended period of time. Backup uses thermal reactors only if problems later develop in the fast reactor portion of a recycling system. Thermal recycle can also provide benefits when used as pure thermal recycling, with no intention to use fast reactors. However, long term, the pure thermal recycling approach is inadequate to meet several objectives.

Steven Piet; Gretchen E. Matthern; Jacob J. Jacobson

2007-09-01T23:59:59.000Z

424

ARM - Measurement - Hydrometeor image  

NLE Websites -- All DOE Office Websites (Extended Search)

image image ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Measurement : Hydrometeor image Images of hydrometeors from which one can derive characteristics such as size and shape. Categories Cloud Properties Instruments The above measurement is considered scientifically relevant for the following instruments. Refer to the datastream (netcdf) file headers of each instrument for a list of all available measurements, including those recorded for diagnostic or quality assurance purposes. Field Campaign Instruments LEARJET : Lear Jet PARTIMG : Particle imager UAV-PROTEUS-MICRO : Proteus Cloud Microphysics Instruments SPEC-CPI : Stratton Park Engineering Company - Cloud particle imager UAV-PROTEUS : UAV Proteus

425

Video Toroid Cavity Imager  

DOE Patents (OSTI)

A video toroid cavity imager for in situ measurement of electrochemical properties of an electrolytic material sample includes a cylindrical toroid cavity resonator containing the sample and employs NMR and video imaging for providing high-resolution spectral and visual information of molecular characteristics of the sample on a real-time basis. A large magnetic field is applied to the sample under controlled temperature and pressure conditions to simultaneously provide NMR spectroscopy and video imaging capabilities for investigating electrochemical transformations of materials or the evolution of long-range molecular aggregation during cooling of hydrocarbon melts. The video toroid cavity imager includes a miniature commercial video camera with an adjustable lens, a modified compression coin cell imager with a fiat circular principal detector element, and a sample mounted on a transparent circular glass disk, and provides NMR information as well as a video image of a sample, such as a polymer film, with micrometer resolution.

Gerald, Rex E. II; Sanchez, Jairo; Rathke, Jerome W.

2004-08-10T23:59:59.000Z

426

Video image position determination  

DOE Patents (OSTI)

The present invention generally relates to the control of video and optical information and, more specifically, to control systems utilizing video images to provide control. Accurate control of video images and laser beams is becoming increasingly important as the use of lasers for machine, medical and experimental processes escalates. In, AURORA, an installation at Los Alamos National Laboratory dedicated to laser fusion research, it is necessary to precisely control the path and angle of up to 96 lasers beams. This invention is comprised of an optical beam position controller in which a video camera captures an image of the beam in its video frames, and conveys those images to a processing board which calculates the centroid coordinates for the image. The image coordinates are used by motor controllers and stepper motors to position the beam in a predetermined alignment. In one embodiment, system noise, used in conjunction with Bernoulli trials, yields higher resolution centroid coordinates.

Christensen, W.; Anderson, F.L.; Kortegaard, B.L.

1990-01-01T23:59:59.000Z

427

Video image position determination  

DOE Patents (OSTI)

The present invention generally relates to the control of video and optical information and, more specifically, to control systems utilizing video images to provide control. Accurate control of video images and laser beams is becoming increasingly important as the use of lasers for machine, medical and experimental processes escalates. In, AURORA, an installation at Los Alamos National Laboratory dedicated to laser fusion research, it is necessary to precisely control the path and angle of up to 96 lasers beams. This invention is comprised of an optical beam position controller in which a video camera captures an image of the beam in its video frames, and conveys those images to a processing board which calculates the centroid coordinates for the image. The image coordinates are used by motor controllers and stepper motors to position the beam in a predetermined alignment. In one embodiment, system noise, used in conjunction with Bernoulli trials, yields higher resolution centroid coordinates.

Christensen, W.; Anderson, F.L.; Kortegaard, B.L.

1990-12-31T23:59:59.000Z

428

Active solar thermal design manual  

SciTech Connect

This manual is aimed at systems design engineers, architects, system supplier/installers, and contractor/builders. Practical information for both skilled and inexperienced designers. Solar thermal applications focuses on residential and commercial space heating, potable hot water heating, process water heating, and space cooling.

1985-01-01T23:59:59.000Z

429

Thermally insulated windows and doors  

SciTech Connect

Complete thermal insulation of metal rails and stiles in vertically or horizontally sliding or rolling windows or doors is provided by including in the frame thereof centered rigid plastic shapes which extend between panels of the windows or doors. All rails and stiles of each panel are thereby exposed only to either interior or exterior ambient temperatures.

Schmidt, D.F.

1979-05-01T23:59:59.000Z

430

HYDROGEOLOGY OF THE THERMAL LANDSLIDE  

DOE Green Energy (OSTI)

The large Thermal Landslide overlies the initial area of geothermal development at The Geysers. The landslide is waterbearing while the underlying Franciscan formation bedrock units are essentially non-waterbearing except where affected by hydrothermal alteration. Perched ground water moving through the landslide is heated prior to discharge as spring flow.

Vantine, J.

1985-01-22T23:59:59.000Z

431

Thermal decomposition of mercuric sulfide  

Science Conference Proceedings (OSTI)

The rate of thermal decomposition of mercuric sulfide (HgS) has been measured at temperatures from 265 to 345 C. These data have been analyzed using a first-order chemical reaction model for the time dependence of the reaction and the Arrhenius equation for the temperature dependence of the rate constant. Using this information, the activation energy for the reaction was found to be 55 kcal/mol. Significant reaction vessel surface effects obscured the functional form of the time dependence of the initial portion of the reaction. The data and the resulting time-temperature reaction-rate model were used to predict the decomposition rate of HgS as a function of time and temperature in thermal treatment systems. Data from large-scale thermal treatment studies already completed were interpreted in terms of the results of this study. While the data from the large-scale thermal treatment studies were consistent with the data from this report, mass transport effects may have contributed to the residual amount of mercury which remained in the soil after most of the large-scale runs.

Leckey, J.H.; Nulf, L.E.

1994-10-28T23:59:59.000Z

432

Solar mechanics thermal response capabilities.  

DOE Green Energy (OSTI)

In many applications, the thermal response of structures exposed to solar heat loads is of interest. Solar mechanics governing equations were developed and integrated with the Calore thermal response code via user subroutines to provide this computational simulation capability. Solar heat loads are estimated based on the latitude and day of the year. Vector algebra is used to determine the solar loading on each face of a finite element model based on its orientation relative to the sun as the earth rotates. Atmospheric attenuation is accounted for as the optical path length varies from sunrise to sunset. Both direct and diffuse components of solar flux are calculated. In addition, shadowing of structures by other structures can be accounted for. User subroutines were also developed to provide convective and radiative boundary conditions for the diurnal variations in air temperature and effective sky temperature. These temperature boundary conditions are based on available local weather data and depend on latitude and day of the year, consistent with the solar mechanics formulation. These user subroutines, coupled with the Calore three-dimensional thermal response code, provide a complete package for addressing complex thermal problems involving solar heating. The governing equations are documented in sufficient detail to facilitate implementation into other heat transfer codes. Suggestions for improvements to the approach are offered.

Dobranich, Dean D.

2009-07-01T23:59:59.000Z

433

Solar energy thermalization and storage device  

DOE Patents (OSTI)

A passive solar thermalization and thermal energy storage assembly which is visually transparent. The assembly consists of two substantial parallel, transparent wall members mounted in a rectangular support frame to form a liquid-tight chamber. A semitransparent thermalization plate is located in the chamber, substantially paralled to and about equidistant from the transparent wall members to thermalize solar radiation which is stored in a transparent thermal energy storage liquid which fills the chamber. A number of the devices, as modules, can be stacked together to construct a visually transparent, thermal storage wall for passive solar-heated buildings.

McClelland, John F. (Ames, IA)

1981-09-01T23:59:59.000Z

434

Ferroelectric optical image comparator  

DOE Patents (OSTI)

A ferroelectric optical image comparator has a lead lanthanum zirconate titanate thin-film device which is constructed with a semi-transparent or transparent conductive first electrode on one side of the thin film, a conductive metal second electrode on the other side of the thin film, and the second electrode is in contact with a nonconducting substrate. A photoinduced current in the device represents the dot product between a stored image and an image projected onto the first electrode. One-dimensional autocorrelations are performed by measuring this current while displacing the projected image. 7 figures.

Butler, M.A.; Land, C.E.; Martin, S.J.; Pfeifer, K.B.

1993-11-30T23:59:59.000Z

435

Ferroelectric optical image comparator  

DOE Patents (OSTI)

A ferroelectric optical image comparator has a lead lanthanum zirconate titanate thin-film device which is constructed with a semi-transparent or transparent conductive first electrode on one side of the thin film, a conductive metal second electrode on the other side of the thin film, and the second electrode is in contact with a nonconducting substrate. A photoinduced current in the device represents the dot product between a stored image and an image projected onto the first electrode. One-dimensional autocorrelations are performed by measuring this current while displacing the projected image.

Butler, Michael A. (Albuquerque, NM); Land, Cecil E. (Albuquerque, NM); Martin, Stephen J. (Albuquerque, NM); Pfeifer, Kent B. (Los Lunas, NM)

1993-01-01T23:59:59.000Z

436

Image Shift Measurement  

Science Conference Proceedings (OSTI)

... Set the write directory to a new folder for the cropped images. Use Process Folder / Text file / Template to make the boiler plate processing file. ...

437

Manhattan Project: Places Images  

Office of Scientific and Technical Information (OSTI)

PLACES IMAGES PLACES IMAGES Resources > Photo Gallery Scroll down to see each of these images individually. The images are: 1. Remains of a Shinto Shrine, Nagasaki, October 1945 (courtesy the United States Marine Corps, Lieutenant R. J. Battersby, photographer, via the National Archives); 2. University of California, Berkeley, 1940 (courtesy the Lawrence Berkeley National Laboratory); 3. Aerial photograph of the Trinity Site after the test (courtesy the Federation of American Scientists); 4. Aerial photograph of Hiroshima before the bombing; 5. Columbia University, 1903 (courtesy the Library of Congress; this photograph originated from the Detroit Publishing Company; it was a 1949 gift to the Library of Congress from the State Historical Society of Colorado).

438

Imaging Beyond Optics  

NLE Websites -- All DOE Office Websites (Extended Search)

Views" piece in that same issue. "Generations of astronomers have used interferometric tests to achieve the proper shape of their mirrors before using them to image the heavens....

439

Kursk Site Image #1  

NLE Websites -- All DOE Office Websites (Extended Search)

Graphs Image KRS-1: Clipping above-ground biomass at the Kursk grassland site, Russia. (Dr. Kira Khodashova and student Nina N., Moscow State University, are estimating monthly...

440

Thermal And-Or Near Infrared At Mt Ranier Area (Frank, 1995) | Open Energy  

Open Energy Info (EERE)

Thermal And-Or Near Infrared At Mt Ranier Area Thermal And-Or Near Infrared At Mt Ranier Area (Frank, 1995) Exploration Activity Details Location Mt Ranier Area Exploration Technique Thermal And-Or Near Infrared Activity Date Usefulness useful DOE-funding Unknown Notes Infrared images acquired through joint US. Department of Energy and U.S. Geological Survey efforts (Kieffer et al., 1982) show a representative pattern of heat emission from the summit area (Fig. 5). References David Frank (1995) Surficial Extent And Conceptual Model Of Hydrothermal System At Mount Rainier, Washington Retrieved from "http://en.openei.org/w/index.php?title=Thermal_And-Or_Near_Infrared_At_Mt_Ranier_Area_(Frank,_1995)&oldid=386481" Categories: Exploration Activities DOE Funded Activities What links here Related changes

Note: This page contains sample records for the topic "imaging multispectral thermal" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Advanced thermally stable jet fuels  

Science Conference Proceedings (OSTI)

The Pennsylvania State University program in advanced thermally stable coal-based jet fuels has five broad objectives: (1) Development of mechanisms of degradation and solids formation; (2) Quantitative measurement of growth of sub-micrometer and micrometer-sized particles suspended in fuels during thermal stressing; (3) Characterization of carbonaceous deposits by various instrumental and microscopic methods; (4) Elucidation of the role of additives in retarding the formation of carbonaceous solids; (5) Assessment of the potential of production of high yields of cycloalkanes by direct liquefaction of coal. Future high-Mach aircraft will place severe thermal demands on jet fuels, requiring the development of novel, hybrid fuel mixtures capable of withstanding temperatures in the range of 400--500 C. In the new aircraft, jet fuel will serve as both an energy source and a heat sink for cooling the airframe, engine, and system components. The ultimate development of such advanced fuels requires a thorough understanding of the thermal decomposition behavior of jet fuels under supercritical conditions. Considering that jet fuels consist of hundreds of compounds, this task must begin with a study of the thermal degradation behavior of select model compounds under supercritical conditions. The research performed by The Pennsylvania State University was focused on five major tasks that reflect the objectives stated above: Task 1: Investigation of the Quantitative Degradation of Fuels; Task 2: Investigation of Incipient Deposition; Task 3: Characterization of Solid Gums, Sediments, and Carbonaceous Deposits; Task 4: Coal-Based Fuel Stabilization Studies; and Task 5: Exploratory Studies on the Direct Conversion of Coal to High Quality Jet Fuels. The major findings of each of these tasks are presented in this executive summary. A description of the sub-tasks performed under each of these tasks and the findings of those studies are provided in the remainder of this volume (Sections 1 through 5).

Schobert, H.H.

1999-01-31T23:59:59.000Z

442

Phase Change Materials for Thermal Energy Storage in Concentrated Solar Thermal Power Plants  

E-Print Network (OSTI)

STORAGE FOR CONCENTRATING SOLAR POWER PLANTS, Eurosun 2010,COST REDUCTION STUDY FOR SOLAR THERMAL POWER PLANTS, Ottawa,Storage in Concentrated Solar Thermal Power Plants A Thesis

Hardin, Corey Lee

2011-01-01T23:59:59.000Z

443

Thermal via placement in 3D ICs  

E-Print Network (OSTI)

As thermal problems become more evident, new physical design paradigms and tools are needed to alleviate them. Incorporating thermal vias into integrated circuits (ICs) is a promising way of mitigating thermal issues by lowering the thermal resistance of the chip itself. However, thermal vias take up valuable routing space, and therefore, algorithms are needed to minimize their usage while placing them in areas where they would make the greatest impact. With the developing technology of three-dimensional integrated circuits (3D ICs), thermal problems are expected to be more prominent, and thermal vias can have a larger impact on them than in traditional 2D ICs. In this paper, thermal vias are assigned to specific areas of a 3D IC and used to adjust their effective thermal conductivities. The thermal via placement method makes iterative adjustments to these thermal conductivities in order to achieve a desired maximum temperature objective. Finite element analysis (FEA) is used in formulating the method and in calculating temperatures quickly during each iteration. As a result, the method efficiently achieves its thermal objective while minimizing the thermal via utilization.

Brent Goplen

2005-01-01T23:59:59.000Z

444

Automatic Image Orientation Determination with Natural Image Statistics  

E-Print Network (OSTI)

Automatic Image Orientation Determination with Natural Image Statistics Siwei Lyu Dept. of Computer a new method for automatically determining image orientations. This method is based on a set of natural image statistics collected from a multi- scale multi-orientation image decomposition (e.g., wavelets

Lyu, Siwei

445

Quantum Imaging: Enhanced Image Formation Using Quantum States of Light  

E-Print Network (OSTI)

Quantum Imaging: Enhanced Image Formation Using Quantum States of Light Robert W. Boyd, Kam Wai, University of Rochester, Rochester, NY 14627, USA ABSTRACT We review recent research in the field of quantum imaging. Quantum imaging deals with the formation of images that possess higher resolution or better

Boyd, Robert W.

446

Tools for Designing Thermal Management of Batteries in Electric Drive Vehicles (Presentation)  

DOE Green Energy (OSTI)

Temperature has a significant impact on life, performance, and safety of lithium-ion battery technology, which is expected to be the energy storage of choice for electric drive vehicles (xEVs). High temperatures degrade Li-ion cells faster while low temperatures reduce power and energy capabilities that could have cost, reliability, range, or drivability implications. Thermal management of battery packs in xEVs is essential to keep the cells in the desired temperature range and also reduce cell-to-cell temperature variations, both of which impact life and performance. The value that the battery thermal management system provides in reducing battery life and improving performance outweighs its additional cost and complexity. Tools that are essential for thermal management of batteries are infrared thermal imaging, isothermal calorimetry, thermal conductivity meter and computer-aided thermal analysis design software. This presentation provides details of these tools that NREL has used and we believe are needed to design right-sized battery thermal management systems.

Pesaran, A.; Keyser, M.; Kim, G. H.; Santhanagopalan, S.; Smith, K.

2013-02-01T23:59:59.000Z

447

OCEAN THERMAL ENERGY CONVERSION PROGRAMMATIC ENVIRONMENTAL ASSESSMENT  

E-Print Network (OSTI)

DOE-EPA Working Group on Ocean TherUial Energy Conversion,Sands, M.D. (editor) Ocean Thermal Energy Conversion (OTEC)r:he comnercialization of ocean thermal energy conversion

Sands, M.Dale

2013-01-01T23:59:59.000Z

448

Vortex Formation in Ellipsoidal Thermal Bubbles  

Science Conference Proceedings (OSTI)

The rise of an isolated dry thermal bubble in a quiescent unstratified environment is a prototypical natural convective flow. This study considers the rise of an isolated dry thermal bubble of ellipsoidal shape (elliptical in both horizontal and ...

Alan Shapiro; Katharine M. Kanak

2002-07-01T23:59:59.000Z

449

Thermal pumping of light-emitting diodes  

E-Print Network (OSTI)

The work presented here is a study of thermally enhanced injection in light-emitting diodes (LEDs). This effect, which we refer to as "thermal pumping", results from Peltier energy exchange from the lattice to charge ...

Gray, Dodd (Dodd J.)

2011-01-01T23:59:59.000Z

450

Heart imaging method  

DOE Patents (OSTI)

A method for providing an image of the human heart's electrical system derives time-of-flight data from an array of EKG electrodes and this data is transformed into phase information. The phase information, treated as a hologram, is reconstructed to provide an image in one or two dimensions of the electrical system of the functioning heart.

Collins, H. Dale (Richland, WA); Gribble, R. Parks (Richland, WA); Busse, Lawrence J. (Littleton, CO)

1991-01-01T23:59:59.000Z

451

Medical imaging systems  

DOE Patents (OSTI)

A medical imaging system provides simultaneous rendering of visible light and fluorescent images. The system may employ dyes in a small-molecule form that remains in a subject's blood stream for several minutes, allowing real-time imaging of the subject's circulatory system superimposed upon a conventional, visible light image of the subject. The system may also employ dyes or other fluorescent substances associated with antibodies, antibody fragments, or ligands that accumulate within a region of diagnostic significance. In one embodiment, the system provides an excitation light source to excite the fluorescent substance and a visible light source for general illumination within the same optical guide that is used to capture images. In another embodiment, the system is configured for use in open surgical procedures by providing an operating area that is closed to ambient light. More broadly, the systems described herein may be used in imaging applications where a visible light image may be usefully supplemented by an image formed from fluorescent emissions from a fluorescent substance that marks areas of functional interest.

Frangioni, John V. (Wayland, MA)

2012-07-24T23:59:59.000Z

452

DOUBLE MAJORS Imaging Science + ...  

E-Print Network (OSTI)

DOUBLE MAJORS Imaging Science + ... Applied Mathematics Biomedical Sciences Computer Science Undergraduate Research Internships and Cooperative Education (Co-op) (optional) Study Abroad WHY IMAGING SCIENCE Science: BS, MS, PhD Color Science: MS, PhD BS + MS/PhD Combos HUMAN VISION BIO- MEDICAL ASTRO- PHYSICS

Zanibbi, Richard

453

Manhattan Project: Image Retouching`  

Office of Scientific and Technical Information (OSTI)

Image Retouching Image Retouching Resources > Photo Gallery Smyth Report (original) Smyth Report (retouched) Images on this web site have sometimes been "retouched." In every case, however, the intention has been only to restore the image as much as possible to its original condition. Above is a rather extreme example-"before and after" versions of the cover of the Smyth Report (Henry DeWolf Smyth, Atomic Energy for Military Purposes: The Official Report on the Development of the Atomic Bomb under the Auspices of the United States Government, 1940-1945 (Princeton, NJ: Princeton University Press, 1945)). The Smyth Report was commissioned by Leslie Groves and originally issued by the Manhattan Engineer District. Princeton University Press reprinted it in book form as a "public service" with "reproduction in whole or in part authorized and permitted.") Larger versions of the same images are below.

454

GTL Image Gallery  

NLE Websites -- All DOE Office Websites (Extended Search)

Human Genome Project Information • Genomic Science • Microbial Genome Program • sitemap • home Human Genome Project Information • Genomic Science • Microbial Genome Program • sitemap • home Announcing the New Image Gallery Visit the new Image Gallery for an expanded suite of images Biofuels Browse the 2010 "Bioenergy Research Centers: An Overview of the Science" Brochure Gallery. Browse the 2006 "Breaking the Biological Barriers to Cellulosic Ethanol: A Joint Research Agenda" Report Gallery. Browse more biofuels images (includes the June 2006 "Understanding Biomass" Primer Gallery). Systems Biology Browse the August 2005 "Genomics:GTL Roadmap: Systems Biology for Energy and Environment" Gallery. Basic Genomics Browse the Human Chromosome Gallery. Browse more Basic Genomics images. Carbon Cycling

455

User Science Images  

NLE Websites -- All DOE Office Websites (Extended Search)

User Science Images User Science Images User Science Images Sort by: Default | Name | Date (low-high) | Date (high-low) | Category NIMROD-1.png FES: NIMROD Simulation February 18, 2010 | Author(s): Dr. Charlson C. Kim (University of Washington) | Category: Fusion Energy | URL: https://nimrodteam.org/ Download Image: NIMROD-1.png | png | 1.5 MB Trajectory of an energetic ion in a Field Reverse Configuration (FRC) magnetic field. Magnetic separatrix denoted by green surface. Spheres are colored by azimuthal velocity. Image courtesy of Charlson Kim, University of Washington; NERSC repos m487, mp21, m1552 Scheibe.png BER: Pore-Scale Fluid Flow for Subsurface Reactive Transport January 1, 2008 | Author(s): Timothy D. Scheibe, PNNL | Category: Environmental Science | URL: http://http://subsurface.pnl.gov/

456

Efficient Graffiti Image Retrieval  

Science Conference Proceedings (OSTI)

Research of graffiti character recognition and retrieval, as a branch of traditional optical character recognition (OCR), has started to gain attention in recent years. We have investigated the special challenge of the graffiti image retrieval problem and propose a series of novel techniques to overcome the challenges. The proposed bounding box framework locates the character components in the graffiti images to construct meaningful character strings and conduct image-wise and semantic-wise retrieval on the strings rather than the entire image. Using real world data provided by the law enforcement community to the Pacific Northwest National Laboratory, we show that the proposed framework outperforms the traditional image retrieval framework with better retrieval results and improved computational efficiency.

Yang, Chunlei; Wong, Pak C.; Ribarsky, William; Fan, Jianping

2012-07-05T23:59:59.000Z

457

Thermoelectrics and Thermal Transport - Programmaster.org  

Science Conference Proceedings (OSTI)

Mar 14, 2012 ... Energy Nanomaterials: Thermoelectrics and Thermal Transport Sponsored by: The Minerals, Metals and Materials Society, TMS Materials...

458

Thermal Response Testing for Geothermal Heat Exchangers ...  

Science Conference Proceedings (OSTI)

Thermal Response Testing for Geothermal Heat Exchangers Begins. The Net-Zero house features a geothermal heat pump ...

2013-03-12T23:59:59.000Z

459

Solar Thermal Technologies Available for Licensing ...  

Solar Thermal Technologies Available for Licensing U.S. Department of Energy (DOE) laboratories and participating research institutions have ...

460

Thermal Spray Coatings for Coastal Infrastructure  

Science Conference Proceedings (OSTI)

Several protection strategies for coastal infrastructure using thermal-spray technology are presented from research at the Albany Research Center. Thermal-sprayed zinc coatings for anodes in impressed current cathodic protection systems are used to extend the service lives of reinforced concrete bridges along the Oregon coast. Thermal-sprayed Ti is examined as an alternative to the consumable zinc anode. Sealed thermal-sprayed Al is examined as an alternative coating to zinc dust filled polyurethane paint for steel structures.

Holcomb, G.R.; Covino, BernardS. Jr.; Cramer, S.D.; Bullard, S.J.

1997-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "imaging multispectral thermal" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Window performance for human thermal comfort  

E-Print Network (OSTI)

gender, acclimation state, the opportunity to adjust clothing and physical disability on requirements for thermal comfort. Energy

Huizenga, C; Zhang, H.; Mattelaer, P.; Yu, T.; Arens, Edward A; Lyons, P.

2006-01-01T23:59:59.000Z

462

Quantum thermal waves in quantum corrals  

E-Print Network (OSTI)

In this paper the possibility of the generation of the thermal waves in 2D electron gas is investigated. In the frame of the quantum heat transport theory the 2D quantum hyperbolic heat transfer equation is formulated and numerically solved. The obtained solutions are the thermal waves in electron 2D gases. As an exapmle the thermal waves in quantum corrals are described. Key words: 2D electron gas, quantum corrals, thermal waves.

J. Marciak-Kozlowska; M. Kozlowski

2004-05-07T23:59:59.000Z

463

Battery Thermal Modeling and Testing (Presentation)  

DOE Green Energy (OSTI)

This presentation summarizes NREL battery thermal modeling and testing work for the DOE Annual Merit Review, May 9, 2011.

Smith, K.

2011-05-01T23:59:59.000Z

464

THERMAL ENERGY STORAGE IN AQUIFERS WORKSHOP  

E-Print Network (OSTI)

thermal storage can be interfaced with a variety of high temperature heat generating systems, e.g. nuclear

Authors, Various

2011-01-01T23:59:59.000Z

465

Appendix B Metric and Thermal Conversion Tables  

U.S. Energy Information Administration (EIA)

2011 U.S. Energy Information Administration | Natural Gas Annual 193 Appendix B Metric and Thermal Conversion Tables

466

Battery Thermal Management System Design Modeling  

SciTech Connect

Looks at the impact of cooling strategies with air and both direct and indirect liquid cooling for battery thermal management.

Pesaran, A.; Kim, G. H.

2006-11-01T23:59:59.000Z

467

MEMS BASED PYROELECTRIC THERMAL ENERGY HARVESTER - Energy ...  

A pyroelectric thermal energy harvesting apparatus for generating an electric current includes a cantilevered layered pyroelectric capacitor extending ...

468

Solar Thermal Test Facility experiment manual  

DOE Green Energy (OSTI)

Information is provided on administrative procedures, capabilities, and requirements of experimenters using the Solar Thermal Test Facility. (MHR)

Darsey, D. M.; Holmes, J. T.; Seamons, L. O.; Kuehl, D. J.; Davis, D. B.; Stomp, J. M.; Matthews, L. K.; Otts, J. V.

1977-10-01T23:59:59.000Z

469

OCEAN THERMAL ENERGY CONVERSION: AN OVERALL ENVIRONMENTAL ASSESSMENT  

E-Print Network (OSTI)

l OCEAN THERMAL ENERGY CONVERSION: ENVIRONMENTAL ASSESSMENTOcean Thermal Energy Conversion Draft Programmatic Environ-Ocean Thermal Energy Conversion. U.S. DOE Assistant Secre-

Sands, M.Dale

2013-01-01T23:59:59.000Z

470

Thermal Energy Storage for Cooling of Commercial Buildings  

E-Print Network (OSTI)

OF THIS DOCUME THERMAL FOR COOLING ENERGY STORAGE BUILDINGSi- LBL-25393 THERMAL FOR COOLING w ENERGY STORAGE BUILDINGSpeak power periods, thermal storage for cooling has become a

Akbari, H.

2010-01-01T23:59:59.000Z

471

Gas Atomization of Amorphous Aluminum: Part I. Thermal Behavior Calculations  

E-Print Network (OSTI)

article, the thermal history and cooling rate experienced byalloys, knowledge of the thermal history and cooling rate isarticle, the thermal history and cooling rate experienced by

Zheng, Baolong; Lin, Yaojun; Zhou, Yizhang; Lavernia, Enrique J.

2009-01-01T23:59:59.000Z

472

OCEAN THERMAL ENERGY CONVERSION (OTEC) PROGRAMMATIC ENVIRONMENTAL ANALYSIS  

E-Print Network (OSTI)

Thermal Energy Conversion Conference. Ocean Systems Branch,Thermal Energy Conversion Conference. Ocean Systems Branch,thermal energy conversion, June 18, 1979. Ocean Systems

Sands, M. D.

2011-01-01T23:59:59.000Z

473

Recycling of wasted energy : thermal to electrical energy conversion  

E-Print Network (OSTI)

Thermally-Chargeable Supercapacitor Fluctuating Low-GradeThermally-Chargeable Supercapacitor for Fluctuating Low-Thermally-Chargeable Supercapacitor for Fluctuating Low-

Lim, Hyuck

2011-01-01T23:59:59.000Z

474

Thermal Energy Storage for Cooling of Commercial Buildings  

E-Print Network (OSTI)

Building Thermal Energy _Storage in ASEAN Countries,"Company, "Thermal Energy Storage for Cooling," Seminar25393 DE91 ,THERMAL ENERGY STORAGE FOR COOLING OF COMMERCIAL

Akbari, H.

2010-01-01T23:59:59.000Z

475

NREL-Ocean Energy Thermal Conversion | Open Energy Information  

Open Energy Info (EERE)

Ocean Energy Thermal Conversion Jump to: navigation, search Logo: NREL-Ocean Energy Thermal Conversion Name NREL-Ocean Energy Thermal Conversion AgencyCompany Organization...

476

Thermal Conductivity of Cubic and Hexagonal Mesoporous Silica Thin Films  

E-Print Network (OSTI)

K.L. Fang, Anisotropic thermal conductivity of nanoporousmesoporous silica as a thermal isolation layer, Ceramicsand V. Wittwer, Some thermal and optical properties of a

Coquil, Thomas; Richman, Eric K.; Hutchinson, Neal J.; Tolbert, S H; Pilon, Laurent

2009-01-01T23:59:59.000Z

477

Thermal dependence of electrical characteristics of micromachined silica microchannel plates  

E-Print Network (OSTI)

Thermal dependence of electrical characteristics ofresults of our studies on the thermal properties of silicatemperature with a negative thermal coefficient of -0.036

Tremsin, A S; Vallerga, J V; Siegmund, OHW; Beetz, C P; Boerstler, R W

2004-01-01T23:59:59.000Z

478

Thermal-Aware CAD for Modern Integrated Circuits  

E-Print Network (OSTI)

Thermal Background 3.1 HeatExperiments 9.1 Thermal-Floorplanning9.1.1 Fast Thermal Floorplanning . . . . . . . . . . .

Logan, Sheldon Logan Paul

2013-01-01T23:59:59.000Z

479

Guide to Setting Thermal Comfort Criteria and Minimizing Energy...  

NLE Websites -- All DOE Office Websites (Extended Search)

Guide to Setting Thermal Comfort Criteria and Minimizing Energy Use in Delivering Thermal Comfort Title Guide to Setting Thermal Comfort Criteria and Minimizing Energy Use in...

480

Thermal Characterization of Nanostructures and Advanced Engineered Materials  

E-Print Network (OSTI)

A. and McEuen, P. L. , Thermal Transport Measurements ofTomanek, D. , Unusually High Thermal Conductivity of Carbonand Lau, C. N. , Superior thermal conductivity of single-

Goyal, Vivek Kumar

2011-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "imaging multispectral thermal" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Recycling of wasted energy : thermal to electrical energy conversion  

E-Print Network (OSTI)

the portion of thermal energy that can be converted toof high-performance thermal energy harvesting systems, butreferred to as the thermal energy from low- temperature heat

Lim, Hyuck

2011-01-01T23:59:59.000Z

482

Thermal Energy Storage for Cooling of Commercial Buildings  

E-Print Network (OSTI)

of Commercial Building Thermal Energy _Storage in ASEANGas Electric Company, "Thermal Energy Storage for Cooling,"LBL--25393 DE91 ,THERMAL ENERGY STORAGE FOR COOLING OF

Akbari, H.

2010-01-01T23:59:59.000Z

483

OCEAN THERMAL ENERGY CONVERSION: AN OVERALL ENVIRONMENTAL ASSESSMENT  

E-Print Network (OSTI)

M.D. (editor). 1980. Ocean Thermal Energy Conversion Draft1980 :. i l OCEAN THERMAL ENERGY CONVERSION: ENVIRONMENTALDevelopment Plan. Ocean Thermal Energy Conversion. U.S. DOE

Sands, M.Dale

2013-01-01T23:59:59.000Z

484

A Magnetomechanical Thermal Energy Harvester With A Reversible Liquid Interface  

E-Print Network (OSTI)

and Mechanical Model of a Thermal Energy Harvesting Device,M, and Ferrari V. , Thermal energy harvesting throughand G. P. Carman, Thermal energy harvesting device using

He, Hong

2012-01-01T23:59:59.000Z

485

THE MOBILE WINDOW THERMAL TEST FACILITY (MoWiTT)  

E-Print Network (OSTI)

December 3-5, 1979 THE MOBILE WINDOW THERMAL TEST FACILITY (Orlando, Florida. The Mobile Window Thermal Test Facility (Press, 197 . THE NOBILE WINDOW THERMAL TEST FACILITY (

Klems, J. H.

2011-01-01T23:59:59.000Z

486

Smart Thermal Skins for Vehicles  

NLE Websites -- All DOE Office Websites (Extended Search)

8 8 Smart Thermal Skins for Vehicles With a modest effort, many of the energy-efficient technologies developed for buildings can be transferred to the transportation sector. The goal of vehicle thermal management research at LBL is to save the energy equivalent of one to two billion gallons of gasoline per year, and improve the marketability of next-generation vehicles using advanced solar control glazings and insulating shell components to reduce accessory loads. Spectrally selective and electrochromic window glass and lightweight insulating materials improve the fuel efficiency of conventional and hybrid vehicles and extend the range of electric vehicles by reducing the need for air conditioning and heating, and by allowing the downsizing of equipment.

487

Microwavable thermal energy storage material  

DOE Patents (OSTI)

A microwavable thermal energy storage material is provided which includes a mixture of a phase change material and silica, and a carbon black additive in the form of a conformable dry powder of phase change material/silica/carbon black, or solid pellets, films, fibers, moldings or strands of phase change material/high density polyethylene/ethylene-vinyl acetate/silica/carbon black which allows the phase change material to be rapidly heated in a microwave oven. The carbon black additive, which is preferably an electrically conductive carbon black, may be added in low concentrations of from 0.5 to 15% by weight, and may be used to tailor the heating times of the phase change material as desired. The microwavable thermal energy storage material can be used in food serving applications such as tableware items or pizza warmers, and in medical wraps and garments.

Salyer, Ival O. (Dayton, OH)

1998-09-08T23:59:59.000Z

488

Microwavable thermal energy storage material  

DOE Patents (OSTI)

A microwavable thermal energy storage material is provided which includes a mixture of a phase change material and silica, and a carbon black additive in the form of a conformable dry powder of phase change material/silica/carbon black, or solid pellets, films, fibers, moldings or strands of phase change material/high density polyethylene/ethylene vinyl acetate/silica/carbon black which allows the phase change material to be rapidly heated in a microwave oven. The carbon black additive, which is preferably an electrically conductive carbon black, may be added in low concentrations of from 0.5 to 15% by weight, and may be used to tailor the heating times of the phase change material as desired. The microwavable thermal energy storage material can be used in food serving applications such as tableware items or pizza warmers, and in medical wraps and garments. 3 figs.

Salyer, I.O.

1998-09-08T23:59:59.000Z

489

Practical Solar Thermal Chilled Water  

E-Print Network (OSTI)

With the pressing need for the United States to reduce our dependence upon fossil fuels, it has become a national priority to develop technologies that allow practical use of renewable energy sources. One such energy source is sunlight. It has the potential to impact America's use of non-renewable energy beyond its own design capacity by applying it to the optimization of an existing building's system. Solar-thermal chilling systems are not new. However, few of them can be described as a practical success. The primary reason for these disappointments is a misunderstanding of solar energy dynamics by air conditioning designers; combined with a similar misunderstanding by solar engineers of how thermally driven chillers react to the loads and energy sources applied to them. With this in mind, a modeling tool has been developed which provides the flexibility to apply a strategy which can be termed, Optimization by Design.

Leavell, B.

2010-01-01T23:59:59.000Z

490

Solar Thermal Reactor Materials Characterization  

DOE Green Energy (OSTI)

Current research into hydrogen production through high temperature metal oxide water splitting cycles has created a need for robust high temperature materials. Such cycles are further enhanced by the use of concentrated solar energy as a power source. However, samples subjected to concentrated solar radiation exhibited lifetimes much shorter than expected. Characterization of the power and flux distributions representative of the High Flux Solar Furnace(HFSF) at the National Renewable Energy Laboratory(NREL) were compared to ray trace modeling of the facility. In addition, samples of candidate reactor materials were thermally cycled at the HFSF and tensile failure testing was performed to quantify material degradation. Thermal cycling tests have been completed on super alloy Haynes 214 samples and results indicate that maximum temperature plays a significant role in reduction of strength. The number of cycles was too small to establish long term failure trends for this material due to the high ductility of the material.

Lichty, P. R.; Scott, A. M.; Perkins, C. M.; Bingham, C.; Weimer, A. W.

2008-03-01T23:59:59.000Z

491

Edge structure preserving image denoising  

Science Conference Proceedings (OSTI)

Image denoising is important in image analysis. It is often used for pre-processing images so that subsequent image analysis is more reliable. Besides noise removal, one important requirement for image denoising procedures is that they should preserve ... Keywords: Angles, Curvature, Edges, Jump-preserving surface estimation, Local smoothing, Nonparametric regression, Surface estimation

Peihua Qiu; Partha Sarathi Mukherjee

2010-10-01T23:59:59.000Z

492

Adaptive wiener image restoration kernel  

DOE Patents (OSTI)

A method and device for restoration of electro-optical image data using an adaptive Wiener filter begins with constructing imaging system Optical Transfer Function, and the Fourier Transformations of the noise and the image. A spatial representation of the imaged object is restored by spatial convolution of the image using a Wiener restoration kernel.

Yuan, Ding (Henderson, NV)

2007-06-05T23:59:59.000Z

493

Thermally stable, plastic-bonded explosives  

DOE Patents (OSTI)

By use of an appropriate thermoplastic rubber as the binder, the thermal stability and thermal stress characteristics of plastic-bonded explosives may be greatly improved. In particular, an HMX-based explosive composition using an oil-extended styrene-ethylenebutylene-styrene block copolymer as the binder exhibits high explosive energy and thermal stability and good handling safety and physical properties.

Benziger, Theodore M. (Santa Fe, NM)

1979-01-01T23:59:59.000Z

494

Hard thermal loops in static background fields  

E-Print Network (OSTI)

We discuss the high temperature behavior of retarded thermal loops in static external fields. We employ an analytic continuation of the imaginary time formalism and use a spectral representation of the thermal amplitudes. We show that, to all orders, the leading contributions of static hard thermal loops can be directly obtained by evaluating them at zero external energies and momenta.

Brandt, F T; Siqueira, J B

2013-01-01T23:59:59.000Z

495

LABORATORY VI ENERGY AND THERMAL PROCESSES  

E-Print Network (OSTI)

LABORATORY VI ENERGY AND THERMAL PROCESSES Lab VI - 1 The change of the internal energy of a system temperature by sweating to cool down. Running seems to be the conversion of chemical energy to thermal energy energy into thermal energy, you decide to make some measurements in the laboratory. To make

Minnesota, University of

496

Practical 1P6 Thermal Analysis  

E-Print Network (OSTI)

and loaded into the tube furnace. The computer software `RS Recorder' logs the data from two furnacesPractical 1P6 Thermal Analysis 1 1P6 ­ Thermal Analysis 1. What you should learn from-tin (electrical solder) by thermal analysis. The results will show that whereas pure metals freeze at one

Paxton, Anthony T.

497

Heat Exchanger Thermal Performance Margin Guidelines  

Science Conference Proceedings (OSTI)

This report provides utility engineers with guidance on how to identify the thermal performance margin that is available in a given heat exchanger by comparing the thermal performance requirement at design limiting conditions to the thermal performance capability of the heat exchanger under those same conditions.

2005-11-30T23:59:59.000Z

498

The Advection of Submesoscale Thermal Features in the Alboran Sea Gyre  

Science Conference Proceedings (OSTI)

NOAA-7 infrared and Nimbus-7 multi-spectral visible imagery of the Alboran Sea collected as part of the Donde Va? experiment during the period 620 October, show the advection of submesoscale cold-water features about the Alboran Sea Gyre.

Paul E. La Violette

1984-03-01T23:59:59.000Z

499

Thermal well-test method  

DOE Patents (OSTI)

A well-test method involving injection of hot (or cold) water into a groundwater aquifer, or injecting cold water into a geothermal reservoir. By making temperature measurements at various depths in one or more observation wells, certain properties of the aquifer are determined. These properties, not obtainable from conventional well test procedures, include the permeability anisotropy, and layering in the aquifer, and in-situ thermal properties. The temperature measurements at various depths are obtained from thermistors mounted in the observation wells.

Tsang, Chin-Fu (Albany, CA); Doughty, Christine A. (Berkeley, CA)

1985-01-01T23:59:59.000Z

500

Electric thermal storage demonstration program  

DOE Green Energy (OSTI)

In early 1989, MMWEC, a joint action agency comprised of 30 municipal light departments in Massachusetts and on affiliate in Rhode Island, responded to a DOE request to proposal for the Least Cost Utility Planning program. The MMWEC submission was for the development of a program, focused on small rural electric utilities, to promote the use of electric thermal storage heating systems in residential applications. This report discusses the demonstration of ETS equipment at four member light departments.

Not Available

1992-02-01T23:59:59.000Z