Sample records for hydrate production technologies

  1. Toward Production From Gas Hydrates: Current Status, Assessment of Resources, and Simulation-Based Evaluationof Technology and Potential

    SciTech Connect (OSTI)

    Reagan, Matthew; Moridis, George J.; Collett, Timothy; Boswell, Ray; Kurihara, M.; Reagan, Matthew T.; Koh, Carolyn; Sloan, E. Dendy

    2008-02-12T23:59:59.000Z

    Gas hydrates are a vast energy resource with global distribution in the permafrost and in the oceans. Even if conservative estimates are considered and only a small fraction is recoverable, the sheer size of the resource is so large that it demands evaluation as a potential energy source. In this review paper, we discuss the distribution of natural gas hydrate accumulations, the status of the primary international R&D programs, and the remaining science and technological challenges facing commercialization of production. After a brief examination of gas hydrate accumulations that are well characterized and appear to be models for future development and gas production, we analyze the role of numerical simulation in the assessment of the hydrate production potential, identify the data needs for reliable predictions, evaluate the status of knowledge with regard to these needs, discuss knowledge gaps and their impact, and reach the conclusion that the numerical simulation capabilities are quite advanced and that the related gaps are either not significant or are being addressed. We review the current body of literature relevant to potential productivity from different types of gas hydrate deposits, and determine that there are consistent indications of a large production potential at high rates over long periods from a wide variety of hydrate deposits. Finally, we identify (a) features, conditions, geology and techniques that are desirable in potential production targets, (b) methods to maximize production, and (c) some of the conditions and characteristics that render certain gas hydrate deposits undesirable for production.

  2. METHANE HYDRATE PRODUCTION FROM ALASKAN PERMAFROST

    SciTech Connect (OSTI)

    Thomas E. Williams; Keith Millheim; Bill Liddell

    2005-03-01T23:59:59.000Z

    Natural-gas hydrates have been encountered beneath the permafrost and considered a nuisance by the oil and gas industry for years. Oil-field engineers working in Russia, Canada and the USA have documented numerous drilling problems, including kicks and uncontrolled gas releases, in Arctic regions. Information has been generated in laboratory studies pertaining to the extent, volume, chemistry and phase behavior of gas hydrates. Scientists studying hydrates agree that the potential is great--on the North Slope of Alaska alone, it has been estimated at 590 TCF. However, little information has been obtained on physical samples taken from actual rock containing hydrates. This gas-hydrate project is a cost-shared partnership between Maurer Technology, Anadarko Petroleum, Noble Corporation, and the U.S. Department of Energy's Methane Hydrate R&D program. The purpose of the project is to build on previous and ongoing R&D in the area of onshore hydrate deposition to help identify, quantify and predict production potential for hydrates located on the North Slope of Alaska. As part of the project work scope, team members drilled and cored the HOT ICE No. 1 on Anadarko leases beginning in January 2003 and completed in March 2004. Due to scheduling constraints imposed by the Arctic drilling season, operations at the site were suspended between April 21, 2003 and January 30, 2004. An on-site core analysis laboratory was designed, constructed and used for determining physical characteristics of frozen core immediately after it was retrieved from the well. The well was drilled from a new and innovative Anadarko Arctic Platform that has a greatly reduced footprint and environmental impact. Final efforts of the project were to correlate geology, geophysics, logs, and drilling and production data and provide this information to scientists for future hydrate operations. Unfortunately, no gas hydrates were encountered in this well; however, a wealth of information was generated and is contained in the project reports.

  3. Detection and Production of Methane Hydrate

    SciTech Connect (OSTI)

    George Hirasaki; Walter Chapman; Gerald Dickens; Colin Zelt; Brandon Dugan; Kishore Mohanty; Priyank Jaiswal

    2011-12-31T23:59:59.000Z

    This project seeks to understand regional differences in gas hydrate systems from the perspective of as an energy resource, geohazard, and long-term climate influence. Specifically, the effort will: (1) collect data and conceptual models that targets causes of gas hydrate variance, (2) construct numerical models that explain and predict regional-scale gas hydrate differences in 2-dimensions with minimal 'free parameters', (3) simulate hydrocarbon production from various gas hydrate systems to establish promising resource characteristics, (4) perturb different gas hydrate systems to assess potential impacts of hot fluids on seafloor stability and well stability, and (5) develop geophysical approaches that enable remote quantification of gas hydrate heterogeneities so that they can be characterized with minimal costly drilling. Our integrated program takes advantage of the fact that we have a close working team comprised of experts in distinct disciplines. The expected outcomes of this project are improved exploration and production technology for production of natural gas from methane hydrates and improved safety through understanding of seafloor and well bore stability in the presence of hydrates. The scope of this project was to more fully characterize, understand, and appreciate fundamental differences in the amount and distribution of gas hydrate and how this would affect the production potential of a hydrate accumulation in the marine environment. The effort combines existing information from locations in the ocean that are dominated by low permeability sediments with small amounts of high permeability sediments, one permafrost location where extensive hydrates exist in reservoir quality rocks and other locations deemed by mutual agreement of DOE and Rice to be appropriate. The initial ocean locations were Blake Ridge, Hydrate Ridge, Peru Margin and GOM. The permafrost location was Mallik. Although the ultimate goal of the project was to understand processes that control production potential of hydrates in marine settings, Mallik was included because of the extensive data collected in a producible hydrate accumulation. To date, such a location had not been studied in the oceanic environment. The project worked closely with ongoing projects (e.g. GOM JIP and offshore India) that are actively investigating potentially economic hydrate accumulations in marine settings. The overall approach was fivefold: (1) collect key data concerning hydrocarbon fluxes which is currently missing at all locations to be included in the study, (2) use this and existing data to build numerical models that can explain gas hydrate variance at all four locations, (3) simulate how natural gas could be produced from each location with different production strategies, (4) collect new sediment property data at these locations that are required for constraining fluxes, production simulations and assessing sediment stability, and (5) develop a method for remotely quantifying heterogeneities in gas hydrate and free gas distributions. While we generally restricted our efforts to the locations where key parameters can be measured or constrained, our ultimate aim was to make our efforts universally applicable to any hydrate accumulation.

  4. METHANE HYDRATE PRODUCTION FROM ALASKAN PERMAFROST

    SciTech Connect (OSTI)

    Donn McGuire; Steve Runyon; Richard Sigal; Bill Liddell; Thomas Williams; George Moridis

    2005-02-01T23:59:59.000Z

    Natural-gas hydrates have been encountered beneath the permafrost and considered a nuisance by the oil and gas industry for years. Engineers working in Russia, Canada and the USA have documented numerous drilling problems, including kicks and uncontrolled gas releases, in arctic regions. Information has been generated in laboratory studies pertaining to the extent, volume, chemistry and phase behavior of gas hydrates. Scientists studying hydrate potential agree that the potential is great--on the North Slope of Alaska alone, it has been estimated at 590 TCF. However, little information has been obtained on physical samples taken from actual rock containing hydrates. This gas-hydrate project is in the final stages of a cost-shared partnership between Maurer Technology, Noble Corporation, Anadarko Petroleum, and the U.S. Department of Energy's Methane Hydrate R&D program. The purpose of the project is to build on previous and ongoing R&D in the area of onshore hydrate deposition to identify, quantify and predict production potential for hydrates located on the North Slope of Alaska. Hot Ice No. 1 was planned to test the Ugnu and West Sak sequences for gas hydrates and a concomitant free gas accumulation on Anadarko's 100% working interest acreage in section 30 of Township 9N, Range 8E of the Harrison Bay quadrangle of the North Slope of Alaska. The Ugnu and West Sak intervals are favorably positioned in the hydrate-stability zone over an area extending from Anadarko's acreage westward to the vicinity of the aforementioned gas-hydrate occurrences. This suggests that a large, north-to-south trending gas-hydrate accumulation may exist in that area. The presence of gas shows in the Ugnu and West Sak reservoirs in wells situated eastward and down dip of the Hot Ice location indicate that a free-gas accumulation may be trapped by gas hydrates. The Hot Ice No. 1 well was designed to core from the surface to the base of the West Sak interval using the revolutionary and new Arctic Drilling Platform in search of gas hydrate and free gas accumulations at depths of approximately 1200 to 2500 ft MD. A secondary objective was the gas-charged sands of the uppermost Campanian interval at approximately 3000 ft. Summary results of geophysical analysis of the well are presented in this report.

  5. METHANE HYDRATE PRODUCTION FROM ALASKAN PERMAFROST

    SciTech Connect (OSTI)

    Ali Kadaster; Bill Liddell; Tommy Thompson; Thomas Williams; Michael Niedermayr

    2005-02-01T23:59:59.000Z

    Natural-gas hydrates have been encountered beneath the permafrost and considered a nuisance by the oil and gas industry for years. Engineers working in Russia, Canada and the USA have documented numerous drilling problems, including kicks and uncontrolled gas releases, in arctic regions. Information has been generated in laboratory studies pertaining to the extent, volume, chemistry and phase behavior of gas hydrates. Scientists studying hydrate potential agree that the potential is great--on the North Slope of Alaska alone, it has been estimated at 590 TCF. However, little information has been obtained on physical samples taken from actual rock containing hydrates. This gas-hydrate project was a cost-shared partnership between Maurer Technology, Noble Corporation, Anadarko Petroleum, and the U.S. Department of Energy's Methane Hydrate R&D program. The purpose of the project is to build on previous and ongoing R&D in the area of onshore hydrate deposition to identify, quantify and predict production potential for hydrates located on the North Slope of Alaska. The work scope included drilling and coring a well (Hot Ice No. 1) on Anadarko leases beginning in FY 2003 and completed in 2004. During the first drilling season, operations were conducted at the site between January 28, 2003 to April 30, 2003. The well was spudded and drilled to a depth of 1403 ft. Due to the onset of warmer weather, work was then suspended for the season. Operations at the site were continued after the tundra was re-opened the following season. Between January 12, 2004 and March 19, 2004, the well was drilled and cored to a final depth of 2300 ft. An on-site core analysis laboratory was built and implemented for determining physical characteristics of the hydrates and surrounding rock. The well was drilled from a new Anadarko Arctic Platform that has a minimal footprint and environmental impact. Final efforts of the project are to correlate geology, geophysics, logs, and drilling and production data and provide this information to scientists developing reservoir models and to research teams for developing future gas-hydrate projects. No gas hydrates were encountered in this well; however, a wealth of information was generated and has been documented by the project team. This Topical Report documents drilling and coring operations and other daily activities.

  6. METHANE HYDRATE PRODUCTION FROM ALASKAN PERMAFROST

    SciTech Connect (OSTI)

    Steve Runyon; Mike Globe; Kent Newsham; Robert Kleinberg; Doug Griffin

    2005-02-01T23:59:59.000Z

    Natural-gas hydrates have been encountered beneath the permafrost and considered a nuisance by the oil and gas industry for years. Engineers working in Russia, Canada and the USA have documented numerous drilling problems, including kicks and uncontrolled gas releases, in arctic regions. Information has been generated in laboratory studies pertaining to the extent, volume, chemistry and phase behavior of gas hydrates. Scientists studying hydrate potential agree that the potential is great--on the North Slope of Alaska alone, it has been estimated at 590 TCF. However, little information has been obtained on physical samples taken from actual rock containing hydrates. This gas-hydrate project was a cost-shared partnership between Maurer Technology, Noble Corporation, Anadarko Petroleum, and the U.S. Department of Energy's Methane Hydrate R&D program. The purpose of the project is to build on previous and ongoing R&D in the area of onshore hydrate deposition to identify, quantify and predict production potential for hydrates located on the North Slope of Alaska. The work scope included drilling and coring a well (Hot Ice No. 1) on Anadarko leases beginning in FY 2003 and completed in 2004. During the first drilling season, operations were conducted at the site between January 28, 2003 to April 30, 2003. The well was spudded and drilled to a depth of 1403 ft. Due to the onset of warmer weather, work was then suspended for the season. Operations at the site were continued after the tundra was re-opened the following season. Between January 12, 2004 and March 19, 2004, the well was drilled and cored to a final depth of 2300 ft. An on-site core analysis laboratory was built and utilized for determining the physical characteristics of the hydrates and surrounding rock. The well was drilled from a new Anadarko Arctic Platform that has a minimal footprint and environmental impact. The final efforts of the project are to correlate geology, geophysics, logs, and drilling and production data and provide this information to scientists planning hydrate exploration and development projects. No gas hydrates were encountered in this well; however, a wealth of information was generated and is contained in this and other project reports. This Topical Report contains details describing logging operations.

  7. METHANE HYDRATE PRODUCTION FROM ALASKAN PERMAFROST

    SciTech Connect (OSTI)

    Thomas E. Williams; Keith Millheim; Bill Liddell

    2005-02-01T23:59:59.000Z

    Natural-gas hydrates have been encountered beneath the permafrost and considered a nuisance by the oil and gas industry for years. Engineers working in Russia, Canada and the USA have documented numerous drilling problems, including kicks and uncontrolled gas releases, in arctic regions. Information has been generated in laboratory studies pertaining to the extent, volume, chemistry and phase behavior of gas hydrates. Scientists studying hydrate potential agree that the potential is great--on the North Slope of Alaska alone, it has been estimated at 590 TCF. However, little information has been obtained on physical samples taken from actual rock containing hydrates. This gas-hydrate project is a cost-shared partnership between Maurer Technology, Anadarko Petroleum, Noble Corporation, and the U.S. Department of Energy's Methane Hydrate R&D program. The purpose of the project is to build on previous and ongoing R&D in the area of onshore hydrate deposition to help identify, quantify and predict production potential for hydrates located on the North Slope of Alaska. As part of the project work scope, team members drilled and cored a well (the Hot Ice No. 1) on Anadarko leases beginning in January 2003 and completed in March 2004. Due to scheduling constraints imposed by the Arctic drilling season, operations at the site were suspended between April 21, 2003 and January 30, 2004. An on-site core analysis laboratory was constructed and used for determining physical characteristics of frozen core immediately after it was retrieved from the well. The well was drilled from a new and innovative Anadarko Arctic Platform that has a greatly reduced footprint and environmental impact. Final efforts of the project were to correlate geology, geophysics, logs, and drilling and production data and provide this information to scientists for future hydrate operations. No gas hydrates were encountered in this well; however, a wealth of information was generated and is contained in the project reports. Documenting the results of this effort are key to extracting lessons learned and maximizing the industry's benefits for future hydrate exploitation.

  8. Methane hydrate research at NETL: Research to make methane production from hydrates a reality

    SciTech Connect (OSTI)

    Taylor, C.E.; Link, D.D.; English, N.

    2007-03-01T23:59:59.000Z

    Research is underway at NETL to understand the physical properties of methane hydrates. Five key areas of research that need further investigation have been identified. These five areas, i.e. thermal properties of hydrates in sediments, kinetics of natural hydrate dissociation, hysteresis effects, permeability of sediments to gas flow and capillary pressures within sediments, and hydrate distribution at porous scale, are important to the production models that will be used for producing methane from hydrate deposits. NETL is using both laboratory experiments and computational modeling to address these five key areas. The laboratory and computational research reinforce each other by providing feedback. The laboratory results are used in the computational models and the results from the computational modeling is used to help direct future laboratory research. The data generated at NETL will be used to help fulfill The National Methane Hydrate R&D Program of a “long-term supply of natural gas by developing the knowledge and technology base to allow commercial production of methane from domestic hydrate deposits by the year 2015” as outlined on the NETL Website [NETL Website, 2005. http://www.netl.doe.gov/scngo/Natural%20Gas/hydrates/index.html]. Laboratory research is accomplished in one of the numerous high-pressure hydrate cells available ranging in size from 0.15 mL to 15 L in volume. A dedicated high-pressure view cell within the Raman spectrometer allows for monitoring the formation and dissociation of hydrates. Thermal conductivity of hydrates (synthetic and natural) at a certain temperature and pressure is performed in a NETL-designed cell. Computational modeling studies are investigating the kinetics of hydrate formation and dissociation, modeling methane hydrate reservoirs, molecular dynamics simulations of hydrate formation, dissociation, and thermal properties, and Monte Carlo simulations of hydrate formation and dissociation.

  9. METHANE HYDRATE PRODUCTION FROM ALASKAN PERMAFROST

    SciTech Connect (OSTI)

    Donn McGuire; Thomas Williams; Bjorn Paulsson; Alexander Goertz

    2005-02-01T23:59:59.000Z

    Natural-gas hydrates have been encountered beneath the permafrost and considered a drilling hazard by the oil and gas industry for years. Drilling engineers working in Russia, Canada and the USA have documented numerous problems, including drilling kicks and uncontrolled gas releases, in arctic regions. Information has been generated in laboratory studies pertaining to the extent, volume, chemistry and phase behavior of gas hydrates. Scientists studying hydrates as a potential energy source agree that the resource potential is great--on the North Slope of Alaska alone, it has been estimated at 590 TCF. However, little information has been obtained from physical samples taken from actual hydrate-bearing rocks. This gas-hydrate project is a cost-shared partnership between Maurer Technology, Anadarko Petroleum, Noble Corporation, and the U.S. Department of Energy's Methane Hydrate R&D program. The purpose of the project is to build on previous and ongoing R&D in the area of onshore hydrate deposition to identify, quantify and predict production potential for hydrates located on the North Slope of Alaska. The project team drilled and continuously cored the Hot Ice No. 1 well on Anadarko-leased acreage beginning in FY 2003 and completed in 2004. An on-site core analysis laboratory was built and used for determining physical characteristics of hydrates and surrounding rock. After the well was logged, a 3D vertical seismic profile (VSP) was recorded to calibrate the shallow geologic section with seismic data and to investigate techniques to better resolve lateral subsurface variations of potential hydrate-bearing strata. Paulsson Geophysical Services, Inc. deployed their 80 level 3C clamped borehole seismic receiver array in the wellbore to record samples every 25 ft. Seismic vibrators were successively positioned at 1185 different surface positions in a circular pattern around the wellbore. This technique generated a 3D image of the subsurface. Correlations were generated of these seismic data with cores, logging, and other well data. Unfortunately, the Hot Ice No. 1 well did not encounter hydrates in the reservoir sands, although brine-saturated sands containing minor amounts of methane were encountered within the hydrate stability zone (HSZ). Synthetic seismograms created from well log data were in agreement with reflectivity data measured by the 3D VSP survey. Modeled synthetic seismograms indicated a detectable seismic response would be expected in the presence of hydrate-bearing sands. Such a response was detected in the 3D VSP data at locations up-dip to the west of the Hot Ice No. 1 wellbore. Results of this project suggest that the presence of hydrate-bearing strata may not be related as simply to HSZ thickness as previously thought. Geological complications of reservoir facies distribution within fluvial-deltaic environments will require sophisticated detection technologies to assess the locations of recoverable volumes of methane contained in hydrates. High-resolution surface seismic data and more rigorous well log data analysis offer the best near-term potential. The hydrate resource potential is huge, but better tools are needed to accurately assess their location, distribution and economic recoverability.

  10. Comparative Assessment of Advanced Gay Hydrate Production Methods

    SciTech Connect (OSTI)

    M. D. White; B. P. McGrail; S. K. Wurstner

    2009-06-30T23:59:59.000Z

    Displacing natural gas and petroleum with carbon dioxide is a proven technology for producing conventional geologic hydrocarbon reservoirs, and producing additional yields from abandoned or partially produced petroleum reservoirs. Extending this concept to natural gas hydrate production offers the potential to enhance gas hydrate recovery with concomitant permanent geologic sequestration. Numerical simulation was used to assess a suite of carbon dioxide injection techniques for producing gas hydrates from a variety of geologic deposit types. Secondary hydrate formation was found to inhibit contact of the injected CO{sub 2} regardless of injectate phase state, thus diminishing the exchange rate due to pore clogging and hydrate zone bypass of the injected fluids. Additional work is needed to develop methods of artificially introducing high-permeability pathways in gas hydrate zones if injection of CO{sub 2} in either gas, liquid, or micro-emulsion form is to be more effective in enhancing gas hydrate production rates.

  11. CFD Modeling of Methane Production from Hydrate-Bearing Reservoir

    SciTech Connect (OSTI)

    Gamwo, I.K.; Myshakin, E.M.; Warzinski, R.P.

    2007-04-01T23:59:59.000Z

    Methane hydrate is being examined as a next-generation energy resource to replace oil and natural gas. The U.S. Geological Survey estimates that methane hydrate may contain more organic carbon the the world's coal, oil, and natural gas combined. To assist in developing this unfamiliar resource, the National Energy Technology Laboratory has undertaken intensive research in understanding the fate of methane hydrate in geological reservoirs. This presentation reports preliminary computational fluid dynamics predictions of methane production from a subsurface reservoir.

  12. Toward Production From Gas Hydrates: Current Status, Assessment of Resources, and Simulation-Based Evaluation of Technology and Potential

    E-Print Network [OSTI]

    Moridis, George J.

    2008-01-01T23:59:59.000Z

    the second involves gas and hydrate (Class 1G, water-poorpriorities for marine gas hydrates, Fire In The Ice, NETLCollett, T. , 1993, Natural gas hydrates of the Prudhoe Bay

  13. Department of Energy Advance Methane Hydrates Science and Technology Projects

    Broader source: Energy.gov [DOE]

    Descriptions for Energy Department Methane Hydrates Science and Technology Projects, August 31, 2012

  14. Toward Production From Gas Hydrates: Current Status, Assessment of Resources, and Simulation-Based Evaluation of Technology and Potential

    E-Print Network [OSTI]

    Moridis, George J.

    2008-01-01T23:59:59.000Z

    to acquire critical reservoir data needed to develop awith synthetic data (describing hydrate reservoirs under thethe flow of reservoir fluids, and (c) data needs that are

  15. ConocoPhillips Gas Hydrate Production Test

    SciTech Connect (OSTI)

    Schoderbek, David; Farrell, Helen; Howard, James; Raterman, Kevin; Silpngarmlert, Suntichai; Martin, Kenneth; Smith, Bruce; Klein, Perry

    2013-06-30T23:59:59.000Z

    Work began on the ConocoPhillips Gas Hydrates Production Test (DOE award number DE-NT0006553) on October 1, 2008. This final report summarizes the entire project from January 1, 2011 to June 30, 2013.

  16. Toward Production From Gas Hydrates: Current Status, Assessment of Resources, and Simulation-Based Evaluation of Technology and Potential

    E-Print Network [OSTI]

    Moridis, George J.

    2008-01-01T23:59:59.000Z

    occurrence while drilling a well (Takahashi et al, 2001;logging while drilling (16 wells), wireline logging (2that has led the drilling of 36 wells in gas hydrate-bearing

  17. Depressurization-induced gas production from Class 1 and Class 2hydrate deposits

    SciTech Connect (OSTI)

    Moridis, George J.; Kowalsky, Michael

    2006-05-12T23:59:59.000Z

    Class 1 hydrate deposits are characterized by a Hydrate-Bearing Layer (HBL) underlain by a two-phase zone involving mobile gas. Such deposits are further divided to Class 1W (involving water and hydrate in the HBL) and Class 1G (involving gas and hydrate in the HBL). In Class 2 deposits, a mobile water zone underlies the hydrate zone. Methane is the main hydrate-forming gas in natural accumulations. Using TOUGH-FX/HYDRATE to study the depressurization-induced gas production from such deposits, we determine that large volumes of gas could be readily produced at high rates for long times using conventional technology. Dissociation in Class 1W deposits proceeds in distinct stages, but is continuous in Class 1G deposits. Hydrates are shown to contribute significantly to the production rate (up to 65 percent and 75 percent in Class 1W and 1G, respectively) and to the cumulative volume of produced gas (up to 45 percent and 54 percent in Class 1W and 1G, respectively). Large volumes of hydrate-originating CH4 could be produced from Class 2 hydrates, but a relatively long lead time would be needed before gas production (which continuously increases over time) attains a substantial level. The permeability of the confining boundaries plays a significant role in gas production from Class 2 deposits. In general, long-term production is needed to realize the full potential of the very promising Class 1 and Class 2 hydrate deposits.

  18. METHANE HYDRATE PRODUCTION FROM ALASKAN PERMAFROST

    SciTech Connect (OSTI)

    Richard Sigal; Kent Newsham; Thomas Williams; Barry Freifeld; Timothy Kneafsey; Carl Sondergeld; Shandra Rai; Jonathan Kwan; Stephen Kirby; Robert Kleinberg; Doug Griffin

    2005-02-01T23:59:59.000Z

    Natural-gas hydrates have been encountered beneath the permafrost and considered a nuisance by the oil and gas industry for years. Engineers working in Russia, Canada and the USA have documented numerous drilling problems, including kicks and uncontrolled gas releases, in arctic regions. Information has been generated in laboratory studies pertaining to the extent, volume, chemistry and phase behavior of gas hydrates. Scientists studying hydrate potential agree that the potential is great--on the North Slope of Alaska alone, it has been estimated at 590 TCF. However, little information has been obtained on physical samples taken from actual rock containing hydrates. The work scope drilled and cored a well The Hot Ice No. 1 on Anadarko leases beginning in FY 2003 and completed in 2004. An on-site core analysis laboratory was built and utilized for determining the physical characteristics of the hydrates and surrounding rock. The well was drilled from a new Anadarko Arctic Platform that has a minimal footprint and environmental impact. The final efforts of the project are to correlate geology, geophysics, logs, and drilling and production data and provide this information to scientists developing reservoir models. No gas hydrates were encountered in this well; however, a wealth of information was generated and is contained in this report. The Hot Ice No. 1 well was drilled from the surface to a measured depth of 2300 ft. There was almost 100% core recovery from the bottom of surface casing at 107 ft to total depth. Based on the best estimate of the bottom of the methane hydrate stability zone (which used new data obtained from Hot Ice No. 1 and new analysis of data from adjacent wells), core was recovered over its complete range. Approximately 580 ft of porous, mostly frozen, sandstone and 155 of conglomerate were recovered in the Ugnu Formation and approximately 215 ft of porous sandstone were recovered in the West Sak Formation. There were gas shows in the bottom part of the Ugnu and throughout the West Sak. No hydrate-bearing zones were identified either in recovered core or on well logs. The base of the permafrost was found at about 1260 ft. With the exception of the deepest sands in the West Sak and some anomalous thin, tight zones, all sands recovered (after thawing) are unconsolidated with high porosity and high permeability. At 800 psi, Ugnu sands have an average porosity of 39.3% and geometrical mean permeability of 3.7 Darcys. Average grain density is 2.64 g/cc. West Sak sands have an average porosity of 35.5%, geometrical mean permeability of 0.3 Darcys, and average grain density of 2.70 g/cc. There were several 1-2 ft intervals of carbonate-cemented sandstone recovered from the West Sak. These intervals have porosities of only a few percent and very low permeability. On a well log they appear as resistive with a high sonic velocity. In shallow sections of other wells these usually are the only logs available. Given the presence of gas in Hot Ice No. 1, if only resistivity and sonic logs and a mud log had been available, tight sand zones may have been interpreted as containing hydrates. Although this finding does not imply that all previously mapped hydrate zones are merely tight sands, it does add a note of caution to the practice of interpreting the presence of hydrates from old well information. The methane hydrate stability zone below the Hot Ice No. 1 location includes thick sections of sandstone and conglomerate which would make excellent reservoir rocks for hydrates and below the permafrost zone shallow gas. The Ugnu formation comprises a more sand-rich section than does the West Sak formation, and the Ugnu sands when cleaned and dried are slightly more porous and significantly more permeable than the West Sak.

  19. The effect of reservoir heterogeneity on gas production from hydrate accumulations in the permafrost

    E-Print Network [OSTI]

    Reagan, M. T.

    2010-01-01T23:59:59.000Z

    Spatial distributions of gas and hydrate phase saturations (from the Mallik 2002 Gas Hydrate Production Research Wellsimulating the behavior of gas hydrates, Energy Conversion

  20. Challenges, uncertainties and issues facing gas production from gas hydrate deposits

    E-Print Network [OSTI]

    Moridis, G.J.

    2011-01-01T23:59:59.000Z

    of Gas Price ($/Mscf) for Offshore Gas Hydrate StudyEvaluation of deepwater gas-hydrate systems. The Leadingfor Gas Production from Gas Hydrates Reservoirs. J. Canadian

  1. Evaluation of the Gas Production Potential of Marine Hydrate Deposits in the Ulleung Basin of the Korean East Sea

    E-Print Network [OSTI]

    Moridis, George J.; Reagan, Matthew T.; Kim, Se-Joon; Seol, Yongkoo; Zhang, Keni

    2007-01-01T23:59:59.000Z

    indicators for natural gas hydrates in shallow sediments ofInternational Symposium on Gas Hydrate Technology, Seoul,International Symposium on Gas Hydrate Technology, Seoul,

  2. Coupled multiphase fluid flow and wellbore stability analysis associated with gas production from oceanic hydrate-bearing sediments

    E-Print Network [OSTI]

    Rutqvist, J.

    2014-01-01T23:59:59.000Z

    Toward Production from Gas Hydrates: Current Status,Facing Gas Production From Gas-Hydrate Deposits. Society ofConference on Gas Hydrates (ICGH 2011), Edinburgh, Scotland,

  3. U.S. and Japan Complete Successful Field Trial of Methane Hydrate...

    Office of Environmental Management (EM)

    Japan Complete Successful Field Trial of Methane Hydrate Production Technologies U.S. and Japan Complete Successful Field Trial of Methane Hydrate Production Technologies May 2,...

  4. Geomechanical response of permafrost-associated hydrate deposits to depressurization-induced gas production

    E-Print Network [OSTI]

    Rutqvist, J.

    2009-01-01T23:59:59.000Z

    Conference on Gas Hydrates (ICGH 2008), Vancouver, BritishGSC et al. Mallik 5L-38 gas hydrate production research wellfrom the Mallik 2002 Gas Hydrate Production Research Well

  5. The Use of Horizontal Wells in Gas Production from Hydrate Accumulations

    E-Print Network [OSTI]

    Moridis, George J.

    2008-01-01T23:59:59.000Z

    E.D. Toward Production From Gas Hydrates: Current Status,International Conference on Gas Hydrates, Trondheim, Norway,for Gas Production from Gas Hydrate Reservoirs, J. Can. Pet.

  6. Natural gas hydrates - issues for gas production and geomechanical stability

    E-Print Network [OSTI]

    Grover, Tarun

    2008-10-10T23:59:59.000Z

    NATURAL GAS HYDRATES – ISSUES FOR GAS PRODUCTION AND GEOMECHANICAL STABILITY A Dissertation by TARUN GROVER Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment of the requirements... for the degree of DOCTOR OF PHILOSOPHY August 2008 Major Subject: Petroleum Engineering NATURAL GAS HYDRATES – ISSUES FOR GAS PRODUCTION AND GEOMECHANICAL STABILITY A Dissertation by TARUN GROVER Submitted to the Office of Graduate...

  7. Method for production of hydrocarbons from hydrates

    DOE Patents [OSTI]

    McGuire, Patrick L. (Los Alamos, NM)

    1984-01-01T23:59:59.000Z

    A method of recovering natural gas entrapped in frozen subsurface gas hydrate formations in arctic regions. A hot supersaturated solution of CaCl.sub.2 or CaBr.sub.2, or a mixture thereof, is pumped under pressure down a wellbore and into a subsurface hydrate formation so as to hydrostatically fracture the formation. The CaCl.sub.2 /CaBr.sub.2 solution dissolves the solid hydrates and thereby releases the gas entrapped therein. Additionally, the solution contains a polymeric viscosifier, which operates to maintain in suspension finely divided crystalline CaCl.sub.2 /CaBr.sub.2 that precipitates from the supersaturated solution as it is cooled during injection into the formation.

  8. The effect of reservoir heterogeneity on gas production from hydrate accumulations in the permafrost

    SciTech Connect (OSTI)

    Reagan, M. T.; Kowalsky, M B.; Moridis, G. J.; Silpngarmlert, S.

    2010-05-01T23:59:59.000Z

    The quantity of hydrocarbon gases trapped in natural hydrate accumulations is enormous, leading to significant interest in the evaluation of their potential as an energy source. Large volumes of gas can be readily produced at high rates for long times from methane hydrate accumulations in the permafrost by means of depressurization-induced dissociation combined with conventional technologies and horizontal or vertical well configurations. Initial studies on the possibility of natural gas production from permafrost hydrates assumed homogeneity in intrinsic reservoir properties and in the initial condition of the hydrate-bearing layers (either due to the coarseness of the model or due to simplifications in the definition of the system). These results showed great promise for gas recovery from Class 1, 2, and 3 systems in the permafrost. This work examines the consequences of inevitable heterogeneity in intrinsic properties, such as in the porosity of the hydrate-bearing formation, or heterogeneity in the initial state of hydrate saturation. Heterogeneous configurations are generated through multiple methods: (1) through defining heterogeneous layers via existing well-log data, (2) through randomized initialization of reservoir properties and initial conditions, and (3) through the use of geostatistical methods to create heterogeneous fields that extrapolate from the limited data available from cores and well-log data. These extrapolations use available information and established geophysical methods to capture a range of deposit properties and hydrate configurations. The results show that some forms of heterogeneity, such as horizontal stratification, can assist in production of hydrate-derived gas. However, more heterogeneous structures can lead to complex physical behavior within the deposit and near the wellbore that may obstruct the flow of fluids to the well, necessitating revised production strategies. The need for fine discretization is crucial in all cases to capture dynamic behavior during production.

  9. Gas production from oceanic Class 2 hydrate accumulations

    SciTech Connect (OSTI)

    Moridis, G.J.; Reagan, M.T.

    2007-02-01T23:59:59.000Z

    Gas hydrates are solid crystalline compounds in which gasmolecules are lodged within the lattices of ice crystals. The vastamounts of hydrocarbon gases that are trapped in hydrate deposits in thepermafrost and in deep ocean sediments may constitute a promising energysource. Class 2 hydrate deposits are characterized by a Hydrate-BearingLayer (HBL) that is underlain by a saturated zone of mobile water. Inthis study we investigated three methods of gas production via verticalwell designs. A long perforated interval (covering the hydrate layer andextending into the underlying water zone) yields the highest gasproduction rates (up to 20 MMSCFD), but is not recommended for long-termproduction because of severe flow blockage caused by secondary hydrateand ice. A short perforated interval entirely within the water zoneallows long-term production, but only at rates of 4.5 7 MMSCFD. A newwell design involving localized heating appears to be the most promising,alleviating possible blockage by secondary hydrate and/or ice near thewellbore) and delivering sustainably large, long-term rates (10-15MMSCFD).The production strategy involves a cyclical process. During eachcycle, gas production continuously increases, while the correspondingwater production continuously decreases. Each cycle is concluded by acavitation event (marked by a precipitous pressure drop at the well),brought about by the inability of thesystem to satisfy the constant massproduction rate QM imposed at the well. This is caused by the increasinggas contribution to the production stream, and/or flow inhibition causedby secondary hydrate and/or ice. In the latter case, short-term thermalstimulation removes the blockage. The results show that gas productionincreases (and the corresponding water-to-gas ratio RWGC decreases) withan increasing(a) QM, (b) hydrate temperature (which defines its stabilityfor a given pressure), and (c) intrinsic permeability. Lower initialhydrate saturations lead initially to higher gas production and a lowerRWGC, but the effect is later reversed as the hydrate is depleted. Thedisposal of the large amounts of produced water does not appear to pose asignificant environmental problem. Production from Class 2 hydrates ischaracterized by (a) the need for confining boundaries, (b) thecontinuously improving RWGC over time (opposite to conventional gasreservoirs), and (c) the development of a free gas zone at the top of thehydrate layer (necessitating the existence of a gas cap forproduction).

  10. Strategies for gas production from oceanic Class 3 hydrate accumulations

    E-Print Network [OSTI]

    Moridis, George J.; Reagan, Matthew T.

    2007-01-01T23:59:59.000Z

    coexistence of aqueous, gas and hydrate phases, indicatingIntrinsic Rate of Methane Gas Hydrate Decomposition”, Chem.Makogon, Y.F. , “Gas hydrates: frozen energy,” Recherche

  11. The Great Gas Hydrate Escape

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    and hydrogen pack into gas hydrates could enlighten alternative fuel production and carbon dioxide storage January 25, 2012 | Tags: Carver, Chemistry, Energy Technologies,...

  12. Methane hydrate gas production: evaluating and exploiting the solid gas resource

    SciTech Connect (OSTI)

    McGuire, P.L.

    1981-01-01T23:59:59.000Z

    Methane hydrate gas could be a tremendous energy resource if methods can be devised to produce this gas economically. This paper examines two methods of producing gas from hydrate deposits by the injection of hot water or steam, and also examines the feasibility of hydraulic fracturing and pressure reduction as a hydrate gas production technique. A hydraulic fracturing technique suitable for hydrate reservoirs and a system for coring hydrate reservoirs are also described.

  13. Coupled multiphase fluid flow and wellbore stability analysis associated with gas production from oceanic hydrate-bearing sediments

    E-Print Network [OSTI]

    Rutqvist, J.

    2014-01-01T23:59:59.000Z

    and arctic onshore gas hydrate production wells. OTC-21015.Bay Unit L-106 Well Unit C gas hydrate deposit in Alaska.Toward Production from Gas Hydrates: Current Status,

  14. The Use of Horizontal Wells in Gas Production from Hydrate Accumulations

    SciTech Connect (OSTI)

    Reagan, Matthew; Moridis, George J.; Reagan, Matthew T.; Zhang, Keni

    2008-04-15T23:59:59.000Z

    The amounts of hydrocarbon gases trapped in natural hydrate accumulations are enormous, leading to a recent interest in the evaluation of their potential as an energy source. Earlier studies have demonstrated that large volumes of gas can be readily produced at high rates for long times from gas hydrate accumulations by means of depressurization-induced dissociation, using conventional technology and vertical wells. The results of this numerical study indicate that the use of horizontal wells does not confer any practical advantages to gas production from Class 1 deposits. This is because of the large disparity in permeabilities between the hydrate layer (HL) and the underlying free gas zone, leading to a hydrate dissociation that proceeds in a horizontally dominant direction and is uniform along the length of the reservoir. When horizontal wells are placed near the base of the HL in Class 2 deposits, the delay in the evolution of a significant gas production rate outweighs their advantages, which include higher rates and the prevention of flow obstruction problems that often hamper the performance of vertical wells. Conversely, placement of a horizontal well near to top of the HL can lead to dramatic increases in gas production from Class 2 and Class 3 deposits over the corresponding production from vertical wells.

  15. Seismic technology will be of key importance for evaluat-ing gas-hydrate resources, particularly across the Gulf of

    E-Print Network [OSTI]

    Texas at Austin, University of

    Seismic technology will be of key importance for evaluat- ing gas-hydrate resources, particularly to be acquired. To apply seismic technology to gas-hydrate studies in the gulf in an optimal manner, it is essential to understand the seismic target that has to be analyzed. What is gas hydrate? Gas hydrate

  16. Natural gas production from hydrate dissociation: An axisymmetric model

    SciTech Connect (OSTI)

    Ahmadi, G. (Clarkson Univ., Pottsdam, NY); Ji, Chuang (Clarkson Univ., Pottsdam, NY); Smith, D.H.

    2007-08-01T23:59:59.000Z

    This paper describes an axisymmetric model for natural gas production from the dissociation of methane hydrate in a confined reservoir by a depressurizing well. During the hydrate dissociation, heat and mass transfer in the reservoir are analyzed. The system of governing equations is solved by a finite difference scheme. For different well pressures and reservoir temperatures, distributions of temperature and pressure in the reservoir, as well as the natural gas production from the well are evaluated. The numerical results are compared with those obtained by a linearization method. It is shown that the gas production rate is a sensitive function of well pressure. The simulation results are compared with the linearization approach and the shortcomings of the earlier approach are discussed.

  17. Gas Production from Hydrate-Bearing Sediments - Emergent Phenomena -

    SciTech Connect (OSTI)

    Jung, J.W. [Georgia Institute of Technology; Jang, J.W. [Georgia Institute of Technology; Tsouris, Costas [ORNL; Phelps, Tommy Joe [ORNL; Rawn, Claudia J [ORNL; Santamarina, Carlos [Georgia Institute of Technology

    2012-01-01T23:59:59.000Z

    Even a small fraction of fine particles can have a significant effect on gas production from hydrate-bearing sediments and sediment stability. Experiments were conducted to investigate the role of fine particles on gas production using a soil chamber that allows for the application of an effective stress to the sediment. This chamber was instrumented to monitor shear-wave velocity, temperature, pressure, and volume change during CO{sub 2} hydrate formation and gas production. The instrumented chamber was placed inside the Oak Ridge National Laboratory Seafloor Process Simulator (SPS), which was used to control the fluid pressure and temperature. Experiments were conducted with different sediment types and pressure-temperature histories. Fines migrated within the sediment in the direction of fluid flow. A vuggy structure formed in the sand; these small cavities or vuggs were precursors to the development of gas-driven fractures during depressurization under a constant effective stress boundary condition. We define the critical fines fraction as the clay-to-sand mass ratio when clays fill the pore space in the sand. Fines migration, clogging, vugs, and gas-driven fracture formation developed even when the fines content was significantly lower than the critical fines fraction. These results show the importance of fines in gas production from hydrate-bearing sediments, even when the fines content is relatively low.

  18. Challenges, uncertainties and issues facing gas production from gas hydrate deposits

    SciTech Connect (OSTI)

    Moridis, G.J.; Collett, T.S.; Pooladi-Darvish, M.; Hancock, S.; Santamarina, C.; Boswell, R.; Kneafsey, T.; Rutqvist, J.; Kowalsky, M.; Reagan, M.T.; Sloan, E.D.; Sum, A.K.; Koh, C.

    2010-11-01T23:59:59.000Z

    The current paper complements the Moridis et al. (2009) review of the status of the effort toward commercial gas production from hydrates. We aim to describe the concept of the gas hydrate petroleum system, to discuss advances, requirement and suggested practices in gas hydrate (GH) prospecting and GH deposit characterization, and to review the associated technical, economic and environmental challenges and uncertainties, including: the accurate assessment of producible fractions of the GH resource, the development of methodologies for identifying suitable production targets, the sampling of hydrate-bearing sediments and sample analysis, the analysis and interpretation of geophysical surveys of GH reservoirs, well testing methods and interpretation of the results, geomechanical and reservoir/well stability concerns, well design, operation and installation, field operations and extending production beyond sand-dominated GH reservoirs, monitoring production and geomechanical stability, laboratory investigations, fundamental knowledge of hydrate behavior, the economics of commercial gas production from hydrates, and the associated environmental concerns.

  19. International Conference on Gas Hydrates May 19-23, 2002, Yokohama

    E-Print Network [OSTI]

    Gudmundsson, Jon Steinar

    4th International Conference on Gas Hydrates May 19-23, 2002, Yokohama Cold Flow Hydrate Technology an opportunity for flow assurance in deepwater production of oil and gas. Hydrate R&D in the Natural Gas Hydrate exchange and reactor units. Introduction Hydrates form when liquid water and natural gas are in contact

  20. Drilling and Production Testing the Methane Hydrate Resource Potential Associated with the Barrow Gas Fields

    SciTech Connect (OSTI)

    Steve McRae; Thomas Walsh; Michael Dunn; Michael Cook

    2010-02-22T23:59:59.000Z

    In November of 2008, the Department of Energy (DOE) and the North Slope Borough (NSB) committed funding to develop a drilling plan to test the presence of hydrates in the producing formation of at least one of the Barrow Gas Fields, and to develop a production surveillance plan to monitor the behavior of hydrates as dissociation occurs. This drilling and surveillance plan was supported by earlier studies in Phase 1 of the project, including hydrate stability zone modeling, material balance modeling, and full-field history-matched reservoir simulation, all of which support the presence of methane hydrate in association with the Barrow Gas Fields. This Phase 2 of the project, conducted over the past twelve months focused on selecting an optimal location for a hydrate test well; design of a logistics, drilling, completion and testing plan; and estimating costs for the activities. As originally proposed, the project was anticipated to benefit from industry activity in northwest Alaska, with opportunities to share equipment, personnel, services and mobilization and demobilization costs with one of the then-active exploration operators. The activity level dropped off, and this benefit evaporated, although plans for drilling of development wells in the BGF's matured, offering significant synergies and cost savings over a remote stand-alone drilling project. An optimal well location was chosen at the East Barrow No.18 well pad, and a vertical pilot/monitoring well and horizontal production test/surveillance well were engineered for drilling from this location. Both wells were designed with Distributed Temperature Survey (DTS) apparatus for monitoring of the hydrate-free gas interface. Once project scope was developed, a procurement process was implemented to engage the necessary service and equipment providers, and finalize project cost estimates. Based on cost proposals from vendors, total project estimated cost is $17.88 million dollars, inclusive of design work, permitting, barging, ice road/pad construction, drilling, completion, tie-in, long-term production testing and surveillance, data analysis and technology transfer. The PRA project team and North Slope have recommended moving forward to the execution phase of this project.

  1. Estimating the upper limit of gas production from Class 2 hydrate accumulations in the permafrost: 2. Alternative well designs and sensitivity analysis

    SciTech Connect (OSTI)

    Moridis, G.; Reagan, M.T.

    2011-01-15T23:59:59.000Z

    In the second paper of this series, we evaluate two additional well designs for production from permafrost-associated (PA) hydrate deposits. Both designs are within the capabilities of conventional technology. We determine that large volumes of gas can be produced at high rates (several MMSCFD) for long times using either well design. The production approach involves initial fluid withdrawal from the water zone underneath the hydrate-bearing layer (HBL). The production process follows a cyclical pattern, with each cycle composed of two stages: a long stage (months to years) of increasing gas production and decreasing water production, and a short stage (days to weeks) that involves destruction of the secondary hydrate (mainly through warm water injection) that evolves during the first stage, and is followed by a reduction in the fluid withdrawal rate. A well configuration with completion throughout the HBL leads to high production rates, but also the creation of a secondary hydrate barrier around the well that needs to be destroyed regularly by water injection. However, a configuration that initially involves heating of the outer surface of the wellbore and later continuous injection of warm water at low rates (Case C) appears to deliver optimum performance over the period it takes for the exhaustion of the hydrate deposit. Using Case C as the standard, we determine that gas production from PA hydrate deposits increases with the fluid withdrawal rate, the initial hydrate saturation and temperature, and with the formation permeability.

  2. Thermal Properties of Methane Hydrate by Experiment and Modeling and Impacts on Technology

    SciTech Connect (OSTI)

    Warzinski, R.P.; Gamwo, I.K.; Rosenbaum, E.M.; Jiang, Hao; Jordan, K.D.; English, N.J. (Univ. College Dublin, IRELAND); Shaw, D.W. (Geneva College, Beaver Falls, PA)

    2008-07-01T23:59:59.000Z

    Thermal properties of pure methane hydrate, under conditions similar to naturally occurring hydrate-bearing sediments being considered for potential production, have been determined both by a new experimental technique and by advanced molecular dynamics simulation (MDS). A novel single-sided, Transient Plane Source (TPS) technique has been developed and used to measure thermal conductivity and thermal diffusivity values of low-porosity methane hydrate formed in the laboratory. The experimental thermal conductivity data are closely matched by results from an equilibrium MDS method using in-plane polarization of the water molecules. MDS was also performed using a non-equilibrium model with a fully polarizable force field for water. The calculated thermal conductivity values from this latter approach were similar to the experimental data. The impact of thermal conductivity on gas production from a hydrate-bearing reservoir was also evaluated using the Tough+/Hydrate reservoir simulator.

  3. Depressurization-induced gas production from Class 1 and Class 2hydrate deposits

    SciTech Connect (OSTI)

    Moridis, George J.; Kowalsky, Michael

    2006-05-12T23:59:59.000Z

    Class 1 hydrate deposits are characterized by aHy-drate-Bearing Layer (HBL) underlain by a two-phase zone involvingmobile gas. Such deposits are further divided to Class 1W (involvingwater and hydrate in the HBL) and Class 1G (involving gas and hydrate inthe HBL). In Class 2 deposits, a mobile water zone underlies the hydratezone. Methane is the main hydrate-forming gas in natural accumulations.Using TOUGH-FX/HYDRATE to study the depressurization-induced gasproduction from such deposits, we determine that large volumes of gascould be readily produced at high rates for long times using conventionaltechnology. Dissociation in Class 1W deposits proceeds in distinctstages, but is continuous in Class 1G deposits. Hydrates are shown tocontribute significantly to the production rate (up to 65 percent and 75percent in Class 1W and 1G, respectively) and to the cumulative volume ofproduced gas (up to 45 percent and 54 percent in Class 1W and 1G,respectively). Large volumes of hydrate-originating CH4 could be producedfrom Class 2 hydrates, but a relatively long lead time would be neededbefore gas production (which continuously increases over time) attains asubstantial level. The permeability of the confining boundaries plays asignificant role in gas production from Class 2 deposits. In general,long-term production is needed to realize the full potential of the verypromising Class 1 and Class 2 hydrate deposits.

  4. Application of fiber optic temperature and strain sensing technology to gas hydrates

    SciTech Connect (OSTI)

    Ulrich, Shannon M [ORNL; Madden, Megan Elwood [ORNL; Rawn, Claudia J [ORNL; Szymcek, Phillip [ORNL; Phelps, Tommy Joe [ORNL

    2008-01-01T23:59:59.000Z

    Gas hydrates may have a significant influence on global carbon cycles due to their large carbon storage capacity in the form of greenhouse gases and their sensitivity to small perturbations in local conditions. Characterizing existing gas hydrate and the formation of new hydrate within sediment systems and their response to small changes in temperature and pressure is imperative to understanding how this dynamic system functions. Fiber optic sensing technology offers a way to measure precisely temperature and strain in harsh environments such as the seafloor. Recent large-scale experiments using Oak Ridge National Laboratory's Seafloor Process Simulator were designed to evaluate the potential of fiber optic sensors to study the formation and dissociation of gas hydrates in 4-D within natural sediments. Results indicate that the fiber optic sensors are so sensitive to experimental perturbations (e.g. refrigeration cycles) that small changes due to hydrate formation or dissociation can be overshadowed.

  5. Petrophysical Characterization and Reservoir Simulator for Methane Gas Production from Gulf of Mexico Hydrates

    SciTech Connect (OSTI)

    Kishore Mohanty; Bill Cook; Mustafa Hakimuddin; Ramanan Pitchumani; Damiola Ogunlana; Jon Burger; John Shillinglaw

    2006-06-30T23:59:59.000Z

    Gas hydrates are crystalline, ice-like compounds of gas and water molecules that are formed under certain thermodynamic conditions. Hydrate deposits occur naturally within ocean sediments just below the sea floor at temperatures and pressures existing below about 500 meters water depth. Gas hydrate is also stable in conjunction with the permafrost in the Arctic. Most marine gas hydrate is formed of microbially generated gas. It binds huge amounts of methane into the sediments. Estimates of the amounts of methane sequestered in gas hydrates worldwide are speculative and range from about 100,000 to 270,000,000 trillion cubic feet (modified from Kvenvolden, 1993). Gas hydrate is one of the fossil fuel resources that is yet untapped, but may play a major role in meeting the energy challenge of this century. In this project novel techniques were developed to form and dissociate methane hydrates in porous media, to measure acoustic properties and CT properties during hydrate dissociation in the presence of a porous medium. Hydrate depressurization experiments in cores were simulated with the use of TOUGHFx/HYDRATE simulator. Input/output software was developed to simulate variable pressure boundary condition and improve the ease of use of the simulator. A series of simulations needed to be run to mimic the variable pressure condition at the production well. The experiments can be matched qualitatively by the hydrate simulator. The temperature of the core falls during hydrate dissociation; the temperature drop is higher if the fluid withdrawal rate is higher. The pressure and temperature gradients are small within the core. The sodium iodide concentration affects the dissociation pressure and rate. This procedure and data will be useful in designing future hydrate studies.

  6. Prediction of gas-hydrate formation conditions in production and surface facilities

    E-Print Network [OSTI]

    Ameripour, Sharareh

    2006-10-30T23:59:59.000Z

    Gas hydrates are a well-known problem in the oil and gas industry and cost millions of dollars in production and transmission pipelines. To prevent this problem, it is important to predict the temperature and pressure under which gas hydrates...

  7. CHARACTERIZING NATURAL GAS HYDRATES IN THE DEEP WATER GULF OF MEXICO: APPLICATIONS FOR SAFE EXPLORATION AND PRODUCTION ACTIVITIES

    SciTech Connect (OSTI)

    Steve Holditch; Emrys Jones

    2003-01-01T23:59:59.000Z

    In 2000, Chevron began a project to learn how to characterize the natural gas hydrate deposits in the deepwater portions of the Gulf of Mexico. A Joint Industry Participation (JIP) group was formed in 2001, and a project partially funded by the U.S. Department of Energy (DOE) began in October 2001. The primary objective of this project is to develop technology and data to assist in the characterization of naturally occurring gas hydrates in the deep water Gulf of Mexico (GOM). These naturally occurring gas hydrates can cause problems relating to drilling and production of oil and gas, as well as building and operating pipelines. Other objectives of this project are to better understand how natural gas hydrates can affect seafloor stability, to gather data that can be used to study climate change, and to determine how the results of this project can be used to assess if and how gas hydrates act as a trapping mechanism for shallow oil or gas reservoirs. During April-September 2002, the JIP concentrated on: Reviewing the tasks and subtasks on the basis of the information generated during the three workshops held in March and May 2002; Writing Requests for Proposals (RFPs) and Cost, Time and Resource (CTRs) estimates to accomplish the tasks and subtasks; Reviewing proposals sent in by prospective contractors; Selecting four contractors; Selecting six sites for detailed review; and Talking to drill ship owners and operators about potential work with the JIP.

  8. CHARACTERIZING NATURAL GAS HYDRATES IN THE DEEP WATER GULF OF MEXICO: APPLICATIONS FOR SAFE EXPLORATION AND PRODUCTION ACTIVITIES

    SciTech Connect (OSTI)

    Steve Holditch; Emrys Jones

    2003-01-01T23:59:59.000Z

    In 2000, Chevron began a project to learn how to characterize the natural gas hydrate deposits in the deepwater portions of the Gulf of Mexico. A Joint Industry Participation (JIP) group was formed in 2001, and a project partially funded by the U.S. Department of Energy (DOE) began in October 2001. The primary objective of this project is to develop technology and data to assist in the characterization of naturally occurring gas hydrates in the deep water Gulf of Mexico (GOM). These naturally occurring gas hydrates can cause problems relating to drilling and production of oil and gas, as well as building and operating pipelines. Other objectives of this project are to better understand how natural gas hydrates can affect seafloor stability, to gather data that can be used to study climate change, and to determine how the results of this project can be used to assess if and how gas hydrates act as a trapping mechanism for shallow oil or gas reservoirs. During the first six months of operation, the primary activities of the JIP were to conduct and plan Workshops, which were as follows: (1) Data Collection Workshop--March 2002 (2) Drilling, Coring and Core Analyses Workshop--May 2002 (3) Modeling, Measurement and Sensors Workshop--May 2002.

  9. Ice method for production of hydrogen clathrate hydrates

    DOE Patents [OSTI]

    Lokshin, Konstantin (Santa Fe, NM); Zhao, Yusheng (Los Alamos, NM)

    2008-05-13T23:59:59.000Z

    The present invention includes a method for hydrogen clathrate hydrate synthesis. First, ice and hydrogen gas are supplied to a containment volume at a first temperature and a first pressure. Next, the containment volume is pressurized with hydrogen gas to a second higher pressure, where hydrogen clathrate hydrates are formed in the process.

  10. Sensitivity Analysis of Gas Production from Class 2 and Class 3 Hydrate Deposits

    SciTech Connect (OSTI)

    Reagan, Matthew; Moridis, George; Zhang, Keni

    2008-05-01T23:59:59.000Z

    Gas hydrates are solid crystalline compounds in which gas molecules are lodged within the lattices of an ice-like crystalline solid. The vast quantities of hydrocarbon gases trapped in hydrate formations in the permafrost and in deep ocean sediments may constitute a new and promising energy source. Class 2 hydrate deposits are characterized by a Hydrate-Bearing Layer (HBL) that is underlain by a saturated zone of mobile water. Class 3 hydrate deposits are characterized by an isolated Hydrate-Bearing Layer (HBL) that is not in contact with any hydrate-free zone of mobile fluids. Both classes of deposits have been shown to be good candidates for exploitation in earlier studies of gas production via vertical well designs - in this study we extend the analysis to include systems with varying porosity, anisotropy, well spacing, and the presence of permeable boundaries. For Class 2 deposits, the results show that production rate and efficiency depend strongly on formation porosity, have a mild dependence on formation anisotropy, and that tighter well spacing produces gas at higher rates over shorter time periods. For Class 3 deposits, production rates and efficiency also depend significantly on formation porosity, are impacted negatively by anisotropy, and production rates may be larger, over longer times, for well configurations that use a greater well spacing. Finally, we performed preliminary calculations to assess a worst-case scenario for permeable system boundaries, and found that the efficiency of depressurization-based production strategies are compromised by migration of fluids from outside the system.

  11. Strategies for gas production from oceanic Class 3 hydrate accumulations

    E-Print Network [OSTI]

    Moridis, George J.; Reagan, Matthew T.

    2007-01-01T23:59:59.000Z

    through the annular gravel pack (kg) N H = hydration numberthrough the annular gravel pack (kg/s) Q V = rate of CH 4ocean through the annular gravel pack (ST m 3 ) X i = water

  12. Coupled flow and geomechanical analysis for gas production in the Prudhoe Bay Unit L-106 well Unit C gas hydrate deposit in Alaska

    E-Print Network [OSTI]

    Kim, J.

    2014-01-01T23:59:59.000Z

    2009. Toward Production From Gas Hydrates: Current Status,Geologic Controls on Gas Hydrate Occurrence in the MountCollett T.S. 1993. Natural Gas Hydrates of the Prudhoe Bay

  13. Estimating the upper limit of gas production from Class 2 hydrate accumulations in the permafrost: 2. Alternative well designs and sensitivity analysis

    E-Print Network [OSTI]

    Moridis, G.

    2011-01-01T23:59:59.000Z

    m). As in all cases of gas hydrates (Moridis et al. , 2007;by destroying the secondary gas hydrate barrier (if such aInduced Gas Production From Class 1 Hydrate Deposits,” SPE

  14. Evaluation of the gas production economics of the gas hydrate cyclic thermal injection model

    SciTech Connect (OSTI)

    Kuuskraa, V.A.; Hammersheimb, E.; Sawyer, W.

    1985-05-01T23:59:59.000Z

    The objective of the work performed under this directive is to assess whether gas hydrates could potentially be technically and economically recoverable. The technical potential and economics of recovering gas from a representative hydrate reservoir will be established using the cyclic thermal injection model, HYDMOD, appropriately modified for this effort, integrated with economics model for gas production on the North Slope of Alaska, and in the deep offshore Atlantic. The results from this effort are presented in this document. In Section 1, the engineering cost and financial analysis model used in performing the economic analysis of gas production from hydrates -- the Hydrates Gas Economics Model (HGEM) -- is described. Section 2 contains a users guide for HGEM. In Section 3, a preliminary economic assessment of the gas production economics of the gas hydrate cyclic thermal injection model is presented. Section 4 contains a summary critique of existing hydrate gas recovery models. Finally, Section 5 summarizes the model modification made to HYDMOD, the cyclic thermal injection model for hydrate gas recovery, in order to perform this analysis.

  15. Evaluation of the Gas Production Potential of Marine HydrateDeposits in the Ulleung Basin of the Korean East Sea

    SciTech Connect (OSTI)

    Moridis, George J.; Reagan, Matthew T.; Kim, Se-Joon; Seol,Yongkoo; Zhang, Keni

    2007-11-16T23:59:59.000Z

    Although significant hydrate deposits are known to exist in the Ulleung Basin of the Korean East Sea, their survey and evaluation as a possible energy resource has not yet been completed. However, it is possible to develop preliminary estimates of their production potential based on the limited data that are currently available. These include the elevation and thickness of the Hydrate-Bearing Layer (HBL), the water depth, and the water temperature at the sea floor. Based on this information, we developed estimates of the local geothermal gradient that bracket its true value. Reasonable estimates of the initial pressure distribution in the HBL can be obtained because it follows closely the hydrostatic. Other critical information needs include the hydrate saturation, and the intrinsic permeabilities of the system formations. These are treated as variables, and sensitivity analysis provides an estimate of their effect on production. Based on the geology of similar deposits, it is unlikely that Ulleung Basin accumulations belong to Class 1 (involving a HBL underlain by a mobile gas zone). If Class 4 (disperse, low saturation accumulations) deposits are involved, they are not likely to have production potential. The most likely scenarios include Class 2 (HBL underlain by a zone of mobile water) or Class 3 (involving only an HBL) accumulations. Assuming nearly impermeable confining boundaries, this numerical study indicates that large production rates (several MMSCFD) are attainable from both Class 2 and Class 3 deposits using conventional technology. The sensitivity analysis demonstrates the dependence of production on the well design, the production rate, the intrinsic permeability of the HBL, the initial pressure, temperature and hydrate saturation, as well as on the thickness of the water zone (Class 2). The study also demonstrates that the presence of confining boundaries is indispensable for the commercially viable production of gas from these deposits.

  16. Challenges, uncertainties and issues facing gas production from gas hydrate deposits

    E-Print Network [OSTI]

    Moridis, G.J.

    2011-01-01T23:59:59.000Z

    Collett, T.S. , 1993. Natural gas hydrates of the Prudhoe2008. Mechanical Properties of Natural Gas Hydrate Bearinggas hydrate reservoir. Natural Gas Hydrate: In Oceanic and

  17. Production of hydrocarbons from hydrates. [DOE patent application

    DOE Patents [OSTI]

    McGuire, P.L.

    1981-09-08T23:59:59.000Z

    An economical and safe method of producing hydrocarbons (or natural gas) from in situ hydrocarbon-containing hydrates is given. Once started, the method will be self-driven and will continue producing hydrocarbons over an extended period of time (i.e., many days).

  18. Simulation of methane production in a laboratory-scale reactor containing hydrate-bearing porous medium

    SciTech Connect (OSTI)

    Gamwo, I.K.; Myshakin, E.M.; Zhang, Wu; Warzinski, R.P.

    2008-01-01T23:59:59.000Z

    Production of methane, induced by depressurization of hydrate sediment in a reactor, was investigated by numerical simulations using a computational fluid dynamics code TOUGH+/Hydrate. The methane production rates were computed at well-pressure drops of 4.2, 14.7, and 29.5 MPa and at a reactor temperature of 21 0C. The predicted behavior of methane production from the reactor is consistent with field-scale simulations and observations. The production rate increases with pressure drop at the well. Evolution patterns of gas and hydrate distributions are similar to those obtained in field-scale simulations. These preliminary results clearly indicate that numerical simulators can be applied to laboratory-scale reactors to anticipate scenarios observed in field experiments.

  19. Numerical simulation studies of gas production scenarios from hydrate accumulations at the Mallik Site, McKenzie Delta, Canada

    SciTech Connect (OSTI)

    Moridis, George J.; Collett, Timothy S.; Dallimore, Scott R.; Satoh, Tohru; Hancock, Stephen; Weatherill, Brian

    2002-03-22T23:59:59.000Z

    The Mallik site represents an onshore permafrost-associated gas hydrate accumulation in the Mackenzie Delta, Northwest Territories, Canada. An 1150 m deep gas hydrate research well was drilled at the site in 1998. The objective of this study is the analysis of various gas production scenarios from several gas-hydrate-bearing zones at the Mallik site. The TOUGH2 general-purpose simulator with the EOSHYDR2 module were used for the analysis. EOSHYDR2 is designed to model the non-isothermal CH{sub 4} (methane) release, phase behavior and flow under conditions typical of methane-hydrate deposits by solving the coupled equations of mass and heat balance, and can describe any combination of gas hydrate dissociation mechanisms. Numerical simulations indicated that significant gas hydrate production at the Mallik site was possible by drawing down the pressure on a thin free-gas zone at the base of the hydrate stability field. Gas hydrate zones with underlying aquifers yielded significant gas production entirely from dissociated gas hydrate, but large amounts of produced water. Lithologically isolated gas-hydrate-bearing reservoirs with no underlying free gas or water zones, and gas-hydrate saturations of at least 50% were also studied. In these cases, it was assumed that thermal stimulation by circulating hot water in the well was the method used to induce dissociation. Sensitivity studies indicated that the methane release from the hydrate accumulations increases with gas-hydrate saturation, the initial formation temperature, the temperature of the circulating water in the well, and the formation thermal conductivity. Methane production appears to be less sensitive to the rock and hydrate specific heat and permeability of the formation.

  20. Numerical studies of gas production from several CH4-hydrate zones at the Mallik Site, Mackenzie Delta, Canada

    SciTech Connect (OSTI)

    Moridis, George J.; Collett, Timothy S.; Dallimore, Scott R.; Satoh, Tohru; Hancock, Steven; Weatherill, Brian

    2002-05-08T23:59:59.000Z

    The Mallik site represents an onshore permafrost-associated gas hydrate accumulation in the Mackenzie Delta, Northwest Territories, Canada. A gas hydrate research well was drilled at the site in 1998. The objective of this study is the analysis of various gas production scenarios from several gas-hydrate-bearing zones at the Mallik site. The TOUGH2 general-purpose simulator with the EOSHYDR2 module were used for the analysis. EOSHYDR2 is designed to model the non-isothermal CH{sub 4} release, phase behavior and flow under conditions typical of methane-hydrate deposits by solving the coupled equations of mass and heat balance, and can describe any combination of gas hydrate dissociation mechanisms. Numerical simulations indicated that significant gas hydrate production at the Mallik site was possible by drawing down the pressure on a thin free-gas zone at the base of the hydrate stability field. Gas hydrate zones with underlying aquifers yielded significant gas production entirely from dissociated gas hydrate, but large amounts of produced water. Lithologically isolated gas-hydrate-bearing reservoirs with no underlying free gas or water zones, and gas-hydrate saturations of at least 50% were also studied. In these cases, it was assumed that thermal stimulation by circulating hot water in the well was the method used to induce dissociation. Sensitivity studies indicated that the methane release from the hydrate accumulations increases with gas-hydrate saturation, the initial formation temperature, the temperature of the circulating water in the well, and the formation thermal conductivity. Methane production appears to be less sensitive to the rock and hydrate specific heat and permeability of the formation.

  1. Technology's Impact on Production

    SciTech Connect (OSTI)

    Rachel Amann; Ellis Deweese; Deborah Shipman

    2009-06-30T23:59:59.000Z

    As part of a cooperative agreement with the United States Department of Energy (DOE) - entitled Technology's Impact on Production: Developing Environmental Solutions at the State and National Level - the Interstate Oil and Gas Compact Commission (IOGCC) has been tasked with assisting state governments in the effective, efficient, and environmentally sound regulation of the exploration and production of natural gas and crude oil, specifically in relation to orphaned and abandoned wells and wells nearing the end of productive life. Project goals include: (1) Developing (a) a model framework for prioritization and ranking of orphaned or abandoned well sites; (b) a model framework for disbursement of Energy Policy Act of 2005 funding; and (c) a research study regarding the current status of orphaned wells in the nation. (2) Researching the impact of new technologies on environmental protection from a regulatory perspective. Research will identify and document (a) state reactions to changing technology and knowledge; (b) how those reactions support state environmental conservation and public health; and (c) the impact of those reactions on oil and natural gas production. (3) Assessing emergent technology issues associated with wells nearing the end of productive life. Including: (a) location of orphaned and abandoned well sites; (b) well site remediation; (c) plugging materials; (d) plug placement; (e) the current regulatory environment; and (f) the identification of emergent technologies affecting end of life wells. New Energy Technologies - Regulating Change, is the result of research performed for Tasks 2 and 3.

  2. Four Critical Needs to Change the Hydrate Energy Paradigm from Assessment to Production: The 2007 Report to Congress by the U.S. Federal methane Hydrate Advisory Committee

    SciTech Connect (OSTI)

    Mahajan,D.; Sloan, D.; Brewer, P.; Dutta, N.; Johnson, A.; Jones, E.; Juenger, K.; Kastner, M.; Masutani, S.; Swenson, R.; Whelan, J.; Wilson, s.; Woolsey, R.

    2009-03-11T23:59:59.000Z

    This work summarizes a two-year study by the U.S. Federal Methane Hydrate Advisory Committee recommending the future needs for federally-supported hydrate research. The Report was submitted to the US Congress on August 14, 2007 and includes four recommendations regarding (a) permafrost hydrate production testing, (b) marine hydrate viability assessment (c) climate effect of hydrates, and (d) international cooperation. A secure supply of natural gas is a vital goal of the U.S. national energy policy because natural gas is the cleanest and most widely used of all fossil fuels. The inherent cleanliness of natural gas, with the lowest CO2 emission per unit of heat energy of any fossil fuel, means substituting gas for coal and fuel oil will reduce emissions that can exacerbate the greenhouse effect. Both a fuel and a feedstock, a secure and reasonably priced supply of natural gas is important to industry, electric power generators, large and small commercial enterprises, and homeowners. Because each volume of solid gas hydrate contains as much as 164 standard volumes of methane, hydrates can be viewed as a concentrated form of natural gas equivalent to compressed gas but less concentrated than liquefied natural gas (LNG). Natural hydrate accumulations worldwide are estimated to contain 700,000 TCF of natural gas, of which 200,000 TCF are located within the United States. Compared with the current national annual consumption of 22 TCF, this estimate of in-place gas in enormous. Clearly, if only a fraction of the hydrated methane is recoverable, hydrates could constitute a substantial component of the future energy portfolio of the Nation (Figure 1). However, recovery poses a major technical and commercial challenge. Such numbers have sparked interest in natural gas hydrates as a potential, long-term source of energy, as well as concerns about any potential impact the release of methane from hydrates might have on the environment. Energy-hungry countries such as India and Japan are outspending the United States on hydrate science and engineering R&D by a factor of 10, and may bring this resource to market as much as a decade before the United States.

  3. Fiber Optic Sensing Technology for Detecting Gas Hydrate Formation and Decomposition

    SciTech Connect (OSTI)

    Rawn, Claudia J [ORNL; Leeman, John R [University of Oklahoma, Norman; Ulrich, Shannon M [ORNL; Alford, Jonathan E [ORNL; Phelps, Tommy Joe [ORNL; Madden, Megan Elwood [University of Oklahoma, Norman

    2011-01-01T23:59:59.000Z

    A fiber optic-based distributed sensing system (DSS) has been integrated with a large volume (72 L) pressure vessel providing high spatial resolution, time resolved, 3-D measurement of hybrid temperature-strain (TS) values within experimental sediment gas hydrate systems. Areas of gas hydrate formation (exothermic) and decomposition (endothermic) can be characterized through this proxy by time series analysis of discrete data points collected along the length of optical fibers placed within a sediment system. Data is visualized as a 'movie' of TS values along the length of each fiber over time. Experiments conducted in the Seafloor Processing Simulator (SPS) at Oak Ridge National Laboratory show clear indications of hydrate formation and dissociation events at expected P-T conditions given the thermodynamics of the CH4-H2O system. The high spatial resolution achieved with fiber optic technology makes the DSS a useful tool for visualizing time resolved formation and dissociation of gas hydrates in large-scale sediment experiments.

  4. Strategies for gas production from hydrate accumulations under various geologic conditions

    E-Print Network [OSTI]

    Moridis, G.; Collett, T.

    2003-01-01T23:59:59.000Z

    JNOC/GSC Mallik 2L- 38 Gas Hydrate Research Well, Mackenziedeposits. INTRODUCTION Gas hydrates are solid crystallinequantity of hydrocarbon gas hydrates range between 10 15 to

  5. Feasibility of monitoring gas hydrate production with time-lapse VSP

    E-Print Network [OSTI]

    Kowalsky, M.B.

    2010-01-01T23:59:59.000Z

    density of the aqueous, gas, and hydrate phases, which isfunction of the aqueous, gas and hydrate phase saturations;in Marine Sediments with Gas Hydrates: Effective Medium

  6. Gas production potential of disperse low-saturation hydrate accumulations in oceanic sediments

    E-Print Network [OSTI]

    Moridis, George J.; Sloan, E. Dendy

    2006-01-01T23:59:59.000Z

    EG. Formation of gas hydrates in natural gas transmissiongeology of natural gas hydrates. Amsterdam: Springer-Verlag;Soloviev, VA. Submarine gas hydrates. St. Petersburg;1998.

  7. The effect of reservoir heterogeneity on gas production from hydrate accumulations in the permafrost

    E-Print Network [OSTI]

    Reagan, M. T.

    2010-01-01T23:59:59.000Z

    Spatial distributions of gas and hydrate phase saturations (Team, 2008, Investigation of gas hydrate bearing sandstoneInternational Conference on Gas Hydrates, July 6-10, 2008,

  8. Alkaline stability of cellulose ethers and impact of their degradation products on cement hydration

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    1 Alkaline stability of cellulose ethers and impact of their degradation products on cement-mail address: pourchez@emse.fr emse-00449712,version1-18Sep2010 Author manuscript, published in "Cement the potential role of cellulose ethers degradation on the alteration of the cement hydration kinetics

  9. Feasibility of monitoring gas hydrate production with time-lapse VSP

    SciTech Connect (OSTI)

    Kowalsky, M.B.; Nakagawa, S.; Moridis, G.J.

    2009-11-01T23:59:59.000Z

    In this work we begin to examine the feasibility of using time-lapse seismic methods-specifically the vertical seismic profiling (VSP) method-for monitoring changes in hydrate accumulations that are predicted to occur during production of natural gas.

  10. Numerical, Laboratory And Field Studies of Gas Production From Natural Hydrate Accumulations in Geologic Media

    E-Print Network [OSTI]

    Moridis, George J.; Kneafsey, Timothy J.; Kowalsky, Michael; Reagan, Matthew

    2006-01-01T23:59:59.000Z

    hydrate (Class 1W) or gas and hydrate (Class 1G). In Class 1Economic Geology of Natural Gas Hydrates, M. Max, A.H. John-of the thermal test of gas hydrate dissociation in the

  11. Depressurization-induced gas production from Class 1 and Class 2 hydrate deposits

    E-Print Network [OSTI]

    Moridis, George J.; Kowalsky, Michael

    2006-01-01T23:59:59.000Z

    hydrate (Class 1W) or gas and hydrate (Class 1G). In Class 1Class 1G (involving gas and hydrate in the HBL). In Class 2JNOC/GSC Mallik 2L-38 Gas Hydrate Research Well, Mackenzie

  12. Glass durability evaluation using product consistency, single-pass flow-through, and vapor hydration tests

    SciTech Connect (OSTI)

    Feng, X.; Hrma, P.; Kim, D. [Pacific Northwest National Lab., Richland, WA (United States)] [and others

    1996-12-31T23:59:59.000Z

    The current approach to assessing chemical durability of waste glasses focuses on a suite of short-term laboratory tests such as dynamic single-pass flow-through (SPFT) tests, static product consistency tests (PCT), and vapor hydration tests. The behavior of the glasses in the three types of tests is quite different, but each test provides insight into the glass corrosion process. The PCT data showed that at constant alumina, silica, and sodium levels the glass durability order for different glass systems is: Boron-series > Boron-Calcium-series > Calcium-series, while the opposite order is observed in SPFT tests. The order for vapor hydration tests is similar to that observed in the PCT tests. The PCT results are consistent with the current understanding of glass structure and are consistent with vapor hydration tests. The SPFT results can be explained using arguments based on solution chemistry.

  13. Geomechanical response of permafrost-associated hydrate deposits to depressurization-induced gas production

    SciTech Connect (OSTI)

    Rutqvist, J.; Moridis, G.J.; Grover, T.; Collett, T.

    2009-02-01T23:59:59.000Z

    In this simulation study, we analyzed the geomechanical response during depressurization production from two known hydrate-bearing permafrost deposits: the Mallik (Northwest Territories, Canada) deposit and Mount Elbert (Alaska, USA) deposit. Gas was produced from these deposits at constant pressure using horizontal wells placed at the top of a hydrate layer (HL), located at a depth of about 900 m at the Mallik and 600 m at the Mount Elbert. The simulation results show that general thermodynamic and geomechanical responses are similar for the two sites, but with substantially higher production and more intensive geomechanical responses at the deeper Mallik deposit. The depressurization-induced dissociation begins at the well bore and then spreads laterally, mainly along the top of the HL. The depressurization results in an increased shear stress within the body of the receding hydrate and causes a vertical compaction of the reservoir. However, its effects are partially mitigated by the relatively stiff permafrost overburden, and compaction of the HL is limited to less than 0.4%. The increased shear stress may lead to shear failure in the hydrate-free zone bounded by the HL overburden and the downward-receding upper dissociation interface. This zone undergoes complete hydrate dissociation, and the cohesive strength of the sediment is low. We determined that the likelihood of shear failure depends on the initial stress state as well as on the geomechanical properties of the reservoir. The Poisson's ratio of the hydrate-bearing formation is a particularly important parameter that determines whether the evolution of the reservoir stresses will increase or decrease the likelihood of shear failure.

  14. Preliminary relative permeability estimates of methane hydrate-bearing sand

    E-Print Network [OSTI]

    Seol, Yongkoo; Kneafsey, Timothy J.; Tomutsa, Liviu; Moridis, George J.

    2006-01-01T23:59:59.000Z

    gas production from gas hydrate reservoirs. We estimated theof gas production from gas hydrate reservoirs. Fieldpermeability function in gas hydrate-bearing sediments is

  15. Sensitivity Analysis of Gas Production from Class 2 and Class 3 Hydrate Deposits

    E-Print Network [OSTI]

    Reagan, Matthew

    2009-01-01T23:59:59.000Z

    a) temperature, (b) gas and hydrate phase saturations, and (A Documented Example of Gas Hydrate Saturated Sand in theMakogon, Y.F. , “Gas hydrates: frozen energy,” Recherche 18(

  16. Vapour Phase Hydration of Blended Oxide Magnox Waste Glasses Neil C. Hyatt,1*

    E-Print Network [OSTI]

    Sheffield, University of

    Vapour Phase Hydration of Blended Oxide ­ Magnox Waste Glasses Neil C. Hyatt,1* William E. Lee,1 BNFL Technology Centre, Sellafield, Seascale, Cumbria, CA20 1PG. UK. ABSTRACT Vapour phase hydration across the alteration layer. Vapour phase hydration leads to formation of surface alteration products

  17. Evaluation of the gas production economics of the gas hydrate cyclic thermal injection model. [Cyclic thermal injection

    SciTech Connect (OSTI)

    Kuuskraa, V.A.; Hammersheimb, E.; Sawyer, W.

    1985-05-01T23:59:59.000Z

    The objective of the work performed under this directive is to assess whether gas hydrates could potentially be technically and economically recoverable. The technical potential and economics of recovering gas from a representative hydrate reservoir will be established using the cyclic thermal injection model, HYDMOD, appropriately modified for this effort, integrated with economics model for gas production on the North Slope of Alaska, and in the deep offshore Atlantic. The results from this effort are presented in this document. In Section 1, the engineering cost and financial analysis model used in performing the economic analysis of gas production from hydrates -- the Hydrates Gas Economics Model (HGEM) -- is described. Section 2 contains a users guide for HGEM. In Section 3, a preliminary economic assessment of the gas production economics of the gas hydrate cyclic thermal injection model is presented. Section 4 contains a summary critique of existing hydrate gas recovery models. Finally, Section 5 summarizes the model modification made to HYDMOD, the cyclic thermal injection model for hydrate gas recovery, in order to perform this analysis.

  18. Investigations into the Polymorphs and Hydration Products of UO3

    SciTech Connect (OSTI)

    Sweet, Lucas E.; Buck, Edgar C.; Henager, Charles H.; Hu, Shenyang Y.; Meier, David E.; Peper, Shane M.; Schwantes, Jon M.; Su, Yin-Fong; Sams, Robert L.; Blake, Thomas A.; Johnson, Timothy J.; Kulp, Thomas J.; Sommers, Ricky L.; Sugar, Joshua D.; Chames, Jeffrey D.

    2012-04-27T23:59:59.000Z

    This work focuses on progress in gaining a better understanding of the polymorphic nature of the UO{sub 3} and UO{sub 3}-water system; one of several important materials associated with the nuclear fuel cycle. The UO{sub 3}-water system is complex and has not been fully characterized, even though these species are common throughout the fuel cycle. For example, most production schemes for UO{sub 3} result in a mixture of up to six different polymorphic phases, and small differences in these conditions will affect phase genesis that ultimately results in measureable changes to the end product. Here we summarize our efforts to better characterize the UO{sub 3}-water system with optical techniques for the purpose of developing some predictive capability of estimating process history and utility, e.g. for polymorphic phases of unknown origin. Specifically, we have investigated three industrially relevant production pathways of UO{sub 3} and discovered a previously unknown low temperature route to {beta}-UO{sub 3}. Powder x-ray diffraction and optical spectroscopies were utilized in our characterization of the UO{sub 3}-water system. Pure phases of UO{sub 3}, its hydrolysis products and starting materials were used to establish optical spectroscopic signatures for these compounds. Preliminary aging studies were conducted on the {alpha}- and {gamma}-phases of UO{sub 3}.

  19. Characterizing Natural Gas Hydrates in the Deep Water Gulf of Mexico: Applications for Safe Exploration and Production Activities

    SciTech Connect (OSTI)

    Bent, Jimmy

    2014-05-31T23:59:59.000Z

    In 2000 Chevron began a project to learn how to characterize the natural gas hydrate deposits in the deep water portion of the Gulf of Mexico (GOM). Chevron is an active explorer and operator in the Gulf of Mexico and is aware that natural gas hydrates need to be understood to operate safely in deep water. In August 2000 Chevron worked closely with the National Energy Technology Laboratory (NETL) of the United States Department of Energy (DOE) and held a workshop in Houston, Texas to define issues concerning the characterization of natural gas hydrate deposits. Specifically, the workshop was meant to clearly show where research, the development of new technologies, and new information sources would be of benefit to the DOE and to the oil and gas industry in defining issues and solving gas hydrate problems in deep water.

  20. Challenges, uncertainties and issues facing gas production from gas hydrate deposits

    E-Print Network [OSTI]

    Moridis, G.J.

    2011-01-01T23:59:59.000Z

    collection of additional reservoir data to support reservoirflow (drawdown) data for those hydrate reservoirs that aregeologic data on gas-hydrate-bearing sand reservoirs in the

  1. Hydrate-phobic surfaces

    E-Print Network [OSTI]

    Smith, Jonathan David, S.M. Massachusetts Institute of Technology

    2011-01-01T23:59:59.000Z

    Clathrate hydrate formation and subsequent plugging of deep-sea oil and gas pipelines represent a significant bottleneck for ultra deep-sea production. Current methods for hydrate mitigation focus on injecting thermodynamic ...

  2. Gas production potential of disperse low-saturation hydrate accumulations in oceanic sediments

    E-Print Network [OSTI]

    Moridis, George J.; Sloan, E. Dendy

    2006-01-01T23:59:59.000Z

    to economically Page viable gas production. The overallare not promising targets for gas production. AcknowledgmentEnergy, Office of Natural Gas and Petroleum Technology,

  3. Geomechanical response of permafrost-associated hydrate deposits to depressurization-induced gas production

    E-Print Network [OSTI]

    Rutqvist, J.

    2009-01-01T23:59:59.000Z

    hydrocarbons) trapped in hydrates is enormous, and easily exceeds the equivalent of all the known conventional

  4. Production of natural gas from methane hydrate by a constant downhole pressure well

    SciTech Connect (OSTI)

    Ahmadi, G. (Clarkson Univ., Potsdam, NY); Ji, C. (Clarkson Univ., Potsdam, NY); Smith, D.H.

    2007-07-01T23:59:59.000Z

    Natural gas production from the dissociation of methane hydrate in a confined reservoir by a depressurizing downhole well was studied. The case that the well pressure was kept constant was treated, and two different linearization schemes in an axisymmetric configuration were used in the analysis. For different fixed well pressures and reservoir temperatures, approximate self similar solutions were obtained. Distributions of temperature, pressure and gas velocity field across the reservoir were evaluated. The distance of the decomposition front from the well and the natural gas production rate as functions of time were also computed. Time evolutions of the resulting profiles were presented in graphical forms, and their differences with the constant well output results were studied. It was shown that the gas production rate was a sensitive function of well pressure and reservoir temperature. The sensitivity of the results to the linearization scheme used was also studied.

  5. Methane Hydrate Production Technologies to be Tested on Alaska's North

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(FactDepartment3311, 3312), OctoberMayEnergy MetalProgram AreasDepartmentSlope

  6. Numerical studies of gas production from several CH4-hydrate zones at the Mallik Site, Mackenzie Delta, Canada

    E-Print Network [OSTI]

    Moridis, George J.; Collett, Timothy S.; Dallimore, Scott R.; Satoh, Tohru; Hancock, Steven; Weatherill, Brian

    2002-01-01T23:59:59.000Z

    JNOC/GSC Mallik 2L-38 Gas Hydrate Research Well, Mackenziepermafrost- associated gas hydrate accumulation in theTerritories, Canada. A gas hydrate research well was drilled

  7. Gas Production From a Cold, Stratigraphically Bounded Hydrate Deposit at the Mount Elbert Site, North Slope, Alaska

    E-Print Network [OSTI]

    Moridis, G.J.

    2010-01-01T23:59:59.000Z

    of P, T, and gas and hydrate phase saturations (S G and SInternational Conference on Gas Hydrates, Vancouver, Britishinterrelations relative to gas hydrates within the North

  8. Hydrogen Production - Current Technology | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    Current Technology Hydrogen Production - Current Technology The development of clean, sustainable, and cost-competitive hydrogen production processes is key to a viable future...

  9. A multi-phase, micro-dispersion reactor for the continuous production of methane gas hydrate

    SciTech Connect (OSTI)

    Taboada Serrano, Patricia L [ORNL; Ulrich, Shannon M [ORNL; Szymcek, Phillip [ORNL; McCallum, Scott [Oak Ridge Associated Universities (ORAU); Phelps, Tommy Joe [ORNL; Palumbo, Anthony Vito [ORNL; Tsouris, Costas [ORNL

    2009-01-01T23:59:59.000Z

    A continuous-jet hydrate reactor originally developed to generate a CO2 hydrate stream has been modified to continuously produce CH4 hydrate. The reactor has been tested in the Seafloor Process Simulator (SPS), a 72-L pressure vessel available at Oak Ridge National Laboratory. During experiments, the reactor was submerged in water inside the SPS and received water from the surrounding through a submersible pump and CH4 externally through a gas booster pump. Thermodynamic conditions in the hydrate stability regime were employed in the experiments. The reactor produced a continuous stream of CH4 hydrate, and based on pressure values and amount of gas injected, the conversion of gas to hydrate was estimated. A conversion of up to 70% was achieved using this reactor.

  10. Challenges, uncertainties and issues facing gas production from gas hydrate deposits

    E-Print Network [OSTI]

    Moridis, G.J.

    2011-01-01T23:59:59.000Z

    Of Gulf Of Mexico Sediments. Mar. Pet. Geo. 23: 893- Yun,of Mexico sediments with and without THF hydrates. Mar. Pet.

  11. Gas Production From a Cold, Stratigraphically Bounded Hydrate Deposit at the Mount Elbert Site, North Slope, Alaska

    SciTech Connect (OSTI)

    Moridis, G.J.; Silpngarmlert, S.; Reagan, M. T.; Collett, T.S.; Zhang, K.

    2009-09-01T23:59:59.000Z

    As part of an effort to identify suitable targets for a planned long-term field test, we investigate by means of numerical simulation the gas production potential from unit D, a stratigraphically bounded (Class 3) permafrost-associated hydrate occurrence penetrated in the ount Elbert well on North Slope, Alaska. This shallow, low-pressure deposit has high porosities, high intrinsic permeabilities and high hydrate saturations. It has a low temperature because of its proximity to the overlying permafrost. The simulation results indicate that vertical ells operating at a constant bottomhole pressure would produce at very low rates for a very long period. Horizontal wells increase gas production by almost two orders of magnitude, but production remains low. Sensitivity analysis indicates that the initial deposit temperature is y the far the most important factor determining production performance (and the most effective criterion for target selection) because it controls the sensible heat available to fuel dissociation.

  12. Product design and development of an aerodynamic hydration system for bicycling and triathlon

    E-Print Network [OSTI]

    Cote, Mark (Mark Brian)

    2007-01-01T23:59:59.000Z

    Proper hydration and aerodynamic performance are both essential needs of a competitive cyclist or triathlete. Several aerodynamic systems have been developed for use on bicycles but few have been designed to be truly ...

  13. Gas Production From a Cold, Stratigraphically Bounded Hydrate Deposit at the Mount Elbert Site, North Slope, Alaska

    E-Print Network [OSTI]

    Moridis, G.J.

    2010-01-01T23:59:59.000Z

    of P, T, and gas and hydrate phase saturations (S G and SJNOC/GSC Mallik 2L-38 Gas Hydrate Research-Well Sediments,interrelations relative to gas hydrates within the North

  14. Numerical simulation studies of gas production scenarios from hydrate accumulations at the Mallik Site, McKenzie Delta, Canada

    E-Print Network [OSTI]

    Moridis, George J.; Collett, Timothy S.; Dallimore, Scott R.; Satoh, Tohru; Hancock, Stephen; Weatherhill, Brian

    2002-01-01T23:59:59.000Z

    permafrost-associated gas hydrate accumulation in theCanada. An 1150 m deep gas hydrate research well was drilledscenarios from several gas-hydrate-bearing zones at the

  15. The use of electrical impedance spectroscopy for monitoring the hydration products of Portland cement mortars with high percentage of pozzolans

    SciTech Connect (OSTI)

    Cruz, J.M. [Departamento de Física Aplicada, Universitat Politècnica de València, Camino de Vera, 46022, Valencia (Spain)] [Departamento de Física Aplicada, Universitat Politècnica de València, Camino de Vera, 46022, Valencia (Spain); Fita, I.C., E-mail: infifer@fis.upv.es [Departamento de Física Aplicada, Universitat Politècnica de València, Camino de Vera, 46022, Valencia (Spain); Soriano, L.; Payá, J.; Borrachero, M.V. [ICITECH, Instituto de Ciencia y Tecnología del Hormigón, Universitat Politècnica de València (Spain)] [ICITECH, Instituto de Ciencia y Tecnología del Hormigón, Universitat Politècnica de València (Spain)

    2013-08-15T23:59:59.000Z

    In this paper, mortars and pastes containing large replacement of pozzolan were studied by mechanical strength, thermogravimetric analysis (TGA), scanning electronic microscopy (SEM), mercury intrusion porosimetry (MIP) and electrical impedance spectroscopy (EIS). The effect of metakaolin (35%) and fly ash (60%) was evaluated and compared with an inert mineral addition (andalusite). The portlandite content was measured, finding that the pozzolanic reaction produced cementing systems with all portlandite fixed. The EIS measurements were analyzed by the equivalent electrical circuit (EEC) method. An EEC with three branches in parallel was applied. The dc resistance was related to the degree of hydration and allowed us to characterize plain and blended mortars. A constant phase element (CPE) quantified the electrical properties of the hydration products located in the solid–solution interface and was useful to distinguish the role of inert and pozzolanic admixtures present in the cement matrix.

  16. Effects of Antiagglomerants on the Interactions between Hydrate Particles

    E-Print Network [OSTI]

    Firoozabadi, Abbas

    InterScience (www.interscience.wiley.com). Hydrate inbibition in natural gas production­574, 2008 Keywords: gas hydrates, antiagglomeration, capillary force, steric repulsion, natural gas production Introduction The undesirable formation of gas hydrates in natural gas pipelines

  17. Assessing the Potential of Using Hydrate Technology to Capture, Store and Transport Gas for the Caribbean Region 

    E-Print Network [OSTI]

    Rajnauth, Jerome Joel

    2012-02-14T23:59:59.000Z

    natural gas as a hydrate while focusing on small scale transportation of natural gas to the Caribbean Islands. This work proposes a workflow for capturing, storing and transporting gas in the hydrate form, particularly for Caribbean situations where...

  18. Numerical simulations of depressurization-induced gas production from gas hydrate reservoirs at the Walker Ridge 312 site, northern Gulf of Mexico

    SciTech Connect (OSTI)

    Myshakin, Evgeniy M.; Gaddipati, Manohar; Rose, Kelly; Anderson, Brian J.

    2012-06-01T23:59:59.000Z

    In 2009, the Gulf of Mexico (GOM) Gas Hydrates Joint-Industry-Project (JIP) Leg II drilling program confirmed that gas hydrate occurs at high saturations within reservoir-quality sands in the GOM. A comprehensive logging-while-drilling dataset was collected from seven wells at three sites, including two wells at the Walker Ridge 313 site. By constraining the saturations and thicknesses of hydrate-bearing sands using logging-while-drilling data, two-dimensional (2D), cylindrical, r-z and three-dimensional (3D) reservoir models were simulated. The gas hydrate occurrences inferred from seismic analysis are used to delineate the areal extent of the 3D reservoir models. Numerical simulations of gas production from the Walker Ridge reservoirs were conducted using the depressurization method at a constant bottomhole pressure. Results of these simulations indicate that these hydrate deposits are readily produced, owing to high intrinsic reservoir-quality and their proximity to the base of hydrate stability. The elevated in situ reservoir temperatures contribute to high (5–40 MMscf/day) predicted production rates. The production rates obtained from the 2D and 3D models are in close agreement. To evaluate the effect of spatial dimensions, the 2D reservoir domains were simulated at two outer radii. The results showed increased potential for formation of secondary hydrate and appearance of lag time for production rates as reservoir size increases. Similar phenomena were observed in the 3D reservoir models. The results also suggest that interbedded gas hydrate accumulations might be preferable targets for gas production in comparison with massive deposits. Hydrate in such accumulations can be readily dissociated due to heat supply from surrounding hydrate-free zones. Special cases were considered to evaluate the effect of overburden and underburden permeability on production. The obtained data show that production can be significantly degraded in comparison with a case using impermeable boundaries. The main reason for the reduced productivity is water influx from the surrounding strata; a secondary cause is gas escape into the overburden. The results dictate that in order to reliably estimate production potential, permeability of the surroundings has to be included in a model.

  19. Green Technology Foresight about environmentally friendly products

    E-Print Network [OSTI]

    Green Technology Foresight about environmentally friendly products and materials - The challenges of Product Development 4 Center for Information and Communication Technologies, Technical University OF THE PROJECT 23 1.2 THE THREE GENERIC TECHNOLOGIES 23 1.3 THE OBJECTIVES OF THE PROJECT 24 1.4 INITIATION

  20. New Oxygen-Production Technology Proving Successful

    Broader source: Energy.gov [DOE]

    The Office of Fossil Energy's National Energy Technology Laboratory has partnered with Air Products and Chemicals Inc. of Allentown, Penn. to develop the Ion Transport Membrane (ITM) Oxygen, a revolutionary new oxygen-production technology that requires less energy and offers lower capital costs than conventional technologies.

  1. Regional long-term production modeling from a single well test, Mount Elbert Gas Hydrate Stratigraphic Test Well, Alaska North Slope

    SciTech Connect (OSTI)

    Anderson, Brian; Kurihara, Masanori; White, Mark D.; Moridis, George J.; Wilson, Scott J.; Pooladi-Darvish, Mehran; Gaddipati, Manohar; Masuda, Yoshihiro; Collett, T. S.; Hunter, Robert B.; Narita, Hideo; Rose, Kelly K.; Boswell, Ray

    2011-02-02T23:59:59.000Z

    Following the results from the open-hole formation pressure response test in the BPXA-DOE-USGS Mount Elbert Gas Hydrate Stratigraphic Test Well (Mount Elbert well) using Schlumberger’s Modular Dynamics Formation Tester (MDT) wireline tool, the International Methane Hydrate Reservoir Simulator Code Comparison project performed long-term reservoir simulations on three different model reservoirs. These descriptions were based on 1) the Mount Elbert gas hydrate accumulation as delineated by an extensive history-matching exercise, 2) an estimation of the hydrate accumulation near the Prudhoe Bay L-pad, and 3) a reservoir that would be down-dip of the Prudhoe Bay L-pad and therefore warmer and deeper. All of these simulations were based, in part, on the results of the MDT results from the Mount Elbert Well. The comparison group’s consensus value for the initial perme- ability of the hydrate-filled reservoir (k = 0.12 mD) and the permeability model based on the MDT history match were used as the basis for subsequent simulations on the three regional scenarios. The simulation results of the five different simulation codes, CMG STARS, HydrateResSim, MH-21 HYDRES, STOMP-HYD, and TOUGHþHYDRATE exhibit good qualitative agreement and the variability of potential methane production rates from gas hydrate reservoirs is illustrated. As expected, the pre- dicted methane production rate increased with increasing in situ reservoir temperature; however, a significant delay in the onset of rapid hydrate dissociation is observed for a cold, homogeneous reservoir and it is found to be repeatable. The inclusion of reservoir heterogeneity in the description of this cold reservoir is shown to eliminate this delayed production. Overall, simulations utilized detailed information collected across the Mount Elbert reservoir either obtained or determined from geophysical well logs, including thickness (37 ft), porosity (35%), hydrate saturation (65%), intrinsic permeability (1000 mD), pore water salinity (5 ppt), and formation temperature (3.3–3.9 ?C). This paper presents the approach and results of extrapolating regional forward production modeling from history-matching efforts on the results from a single well test.

  2. Estimates of Biogenic Methane Production Rates in Deep Marine Sediments at Hydrate Ridge, Cascadia Margin

    SciTech Connect (OSTI)

    F. S. Colwell; S. Boyd; M. E. Delwiche; D. W. Reed; T. J. Phelps; D. T. Newby

    2008-06-01T23:59:59.000Z

    Methane hydrate found in marine sediments is thought to contain gigaton quantities of methane and is considered an important potential fuel source and climate-forcing agent. Much of the methane in hydrates is biogenic, so models that predict the presence and distribution of hydrates require accurate rates of in situ methanogenesis. We estimated the in situ methanogenesis rates in Hydrate Ridge (HR) sediments by coupling experimentally derived minimal rates of methanogenesis to methanogen biomass determinations for discrete locations in the sediment column. When starved in a biomass recycle reactor Methanoculleus submarinus produced ca. 0.017 fmol methane/cell/day. Quantitative polymerase chain reaction (QPCR) directed at the methyl coenzyme M reductase subunit A (mcrA) gene indicated that 75% of the HR sediments analyzed contained <1000 methanogens/g. The highest methanogen numbers were mostly from sediments <10 meters below seafloor. By combining methanogenesis rates for starved methanogens (adjusted to account for in situ temperatures) and the numbers of methanogens at selected depths we derived an upper estimate of <4.25 fmol methane produced/g sediment/day for the samples with fewer methanogens than the QPCR method could detect. The actual rates could vary depending on the real number of methanogens and various seafloor parameters that influence microbial activity. However, our calculated rate is lower than rates previously reported from such sediments and close to the rate derived using geochemical modeling of the sediments. These data will help to improve models that predict microbial gas generation in marine sediments and determine the potential influence of this source of methane on the global carbon cycle.

  3. 2011 Pathways to Commercial Success: Technologies and Products...

    Energy Savers [EERE]

    1 Pathways to Commercial Success: Technologies and Products Supported by the Fuel Cell Technologies Program 2011 Pathways to Commercial Success: Technologies and Products Supported...

  4. 2013 Pathways to Commercial Success: Technologies and Products...

    Energy Savers [EERE]

    2013 Pathways to Commercial Success: Technologies and Products Supported by the Fuel Cell Technologies Office 2013 Pathways to Commercial Success: Technologies and Products...

  5. 2014 Pathways to Commercial Success: Technologies and Products...

    Energy Savers [EERE]

    2014 Pathways to Commercial Success: Technologies and Products Supported by the Fuel Cell Technologies Office 2014 Pathways to Commercial Success: Technologies and Products...

  6. Evaluation of a deposit in the vicinity of the PBU L-106 Site, North Slope, Alaska, for a potential long-term test of gas production from hydrates

    SciTech Connect (OSTI)

    Moridis, G.J.; Reagan, M.T.; Boyle, K.L.; Zhang, K.

    2010-05-01T23:59:59.000Z

    As part of the effort to investigate the technical feasibility of gas production from hydrate deposits, a long-term field test (lasting 18-24 months) is under consideration in a project led by the U.S. Department of Energy. We evaluate a candidate deposit involving the C-Unit in the vicinity of the PBU-L106 site in North Slope, Alaska. This deposit is stratigraphically bounded by impermeable shale top and bottom boundaries (Class 3), and is characterized by high intrinsic permeabilities, high porosity, high hydrate saturation, and a hydrostatic pressure distribution. The C-unit deposit is composed of two hydrate-bearing strata separated by a 30-ft-thick shale interlayer, and its temperatrure across its boundaries ranges between 5 and 6.5 C. We investigate by means of numerical simulation involving very fine grids the production potential of these two deposits using both vertical and horizontal wells. We also explore the sensitivity of production to key parameters such as the hydrate saturation, the formation permeability, and the permeability of the bounding shale layers. Finally, we compare the production performance of the C-Unit at the PBU-L106 site to that of the D-Unit accumulation at the Mount Elbert site, a thinner, single-layer Class 3 deposit on the North Slope of Alaska that is shallower, less-pressurized and colder (2.3-2.6 C). The results indicate that production from horizontal wells may be orders of magnitude larger than that from vertical ones. Additionally, production increases with the formation permeability, and with a decreasing permeability of the boundaries. The effect of the hydrate saturation on production is complex and depends on the time frame of production. Because of higher production, the PBU-L106 deposit appears to have an advantage as a candidate for the long-term test.

  7. Assessing the Potential of Using Hydrate Technology to Capture, Store and Transport Gas for the Caribbean Region

    E-Print Network [OSTI]

    Rajnauth, Jerome Joel

    2012-02-14T23:59:59.000Z

    there are infrastructural constraints such as lack of pipelines. The study shows the gas hydrate value chain for transportation of 5 MMscf/d of natural gas from Trinidad to Jamaica. The analysis evaluated the water required for hydrate formation, effect of composition...

  8. Evaluation of a deposit in the vicinity of the PBU L-106 Site, North Slope, Alaska, for a potential long-term test of gas production from hydrates

    E-Print Network [OSTI]

    Moridis, G.J.

    2010-01-01T23:59:59.000Z

    of P, T, and gas and hydrate phase saturations (S G and SInternational Conference on Gas Hydrates, Vancouver, BritishM. 2008. Investigation of gas hydrate bearing sandstone

  9. Technology and Consumer Products Branch: program plan

    SciTech Connect (OSTI)

    None

    1980-03-01T23:59:59.000Z

    The primary objective of the Technology and Consumer Products Branch (TCP) is to encourage the development and commercialization of energy-efficient technologies and equipment used in buildings and purchased by consumers. The TCP program conducts technical research, development, and demonstration efforts jointly funded with private industry, educational institutions, utilities, and other Federal and state agencies as appropriate. All contracts, grants, or interagency agreements have the major thrust of developing products and disseminating information that will accelerate commercial availability of energy-efficient, low-cost, reliable technologies, techniques, and products suitable for use by consumers and design professionals in the residential and commercial building sectors. Specifically, the technologies pursued by the branch include heating and cooling systems, consumer appliances, lighting design, and systems. Projects for each of these areas are summarized briefly, and publications resulting from the activities are listed.

  10. DOE Fuel Cell Technologies Office Record 12024: Hydrogen Production...

    Energy Savers [EERE]

    DOE Fuel Cell Technologies Office Record 12024: Hydrogen Production Cost Using Low-Cost Natural Gas DOE Fuel Cell Technologies Office Record 12024: Hydrogen Production Cost Using...

  11. Fuel Cell Technologies Researcher Lightens Green Fuel Production...

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    Fuel Cell Technologies Researcher Lightens Green Fuel Production Fuel Cell Technologies Researcher Lightens Green Fuel Production August 25, 2014 - 9:36am Addthis Research funded...

  12. Modeling pure methane hydrate dissociation using a numerical simulator from a novel combination of X-ray computed tomography and macroscopic data

    E-Print Network [OSTI]

    Gupta, A.

    2010-01-01T23:59:59.000Z

    From The Mallik 2002 Gas Hydrate Production Research Wellrate constant of methane gas hydrate decomposition. CanadianJNOC/GSC Mallik 2L-38 Gas Hydrate Research Well, Mackenzie

  13. Hydrogen Production: Overview of Technology Options, January 2009

    Fuel Cell Technologies Publication and Product Library (EERE)

    Overview of technology options for hydrogen production, its challenges and research needs and next steps

  14. Production technology experience in Shell's Michigan waterfloods

    SciTech Connect (OSTI)

    Barnes, P.F.; Tinker, G.E.

    1983-11-01T23:59:59.000Z

    Waterflooding started in the Niagaran carbonate reef oil reservoirs in Northern Michigan in 1978 with Shell's Chester 18 waterflood. Ten waterflood projects had been installed by the spring of 1983. As a result of this experience, significant production technology practices have become established. The majority of the waterflood experience has been in Shell's Gaylord Production Unit located primarily in Otsego and Crawford counties. Specifically, the projects discussed are the Chester 18, Chester 21, Frederic 10, Hayes 15, Hayes 21A, and Mid-Charlton 10 waterfloods. In general, the waterflood program can be characterized by: 1. Very favorable oil production response. 2. Timely and definitive surveillance techniques. 3. Systematic and timely well work on injectors and producers to maintain optimum reservoir withdrawal behavior. 4. Innovative application of artificial lift technology. 5. Aggressive future planning to maintain and improve oil production response.

  15. Production technology experience in Shell's Michigan waterfloods

    SciTech Connect (OSTI)

    Barnes, P.F.; Tinker, G.E.

    1983-01-01T23:59:59.000Z

    Waterflooding started in the Niagaran carbonate reef oil reservoirs in N. Michigan in 1978 with Shell's Chester 18 Waterflood. Ten waterflood projects had been installed by the spring of 1983. As a result of this experience, significant production technology practices have become established. The majority of the waterflood experience has been in Shell's Gaylord Production Unit located primarily in Otsego and Crawford counties. Specifically, the projects discussed are the Chester 18, Chester 21, Frederic 10, Hayes 15, Hayes 21A, and Mid-Charlton 10 waterfloods. In general, the waterflood program can be characterized by (1) a favorable oil production response, (2) timely and definitive surveillance techniques, (3) systematic and timely well work on injectors and producers to maintain optimum reservoir withdrawal behavior, (4) innovative application of artificial lift technology; and (5) aggressive future planning to maintain and improve oil production response.

  16. Production technology experience in Michigan waterfloods

    SciTech Connect (OSTI)

    Burnes, P.F.; Tinker, G.E.

    1985-08-01T23:59:59.000Z

    Waterflooding started in the Niagaran carbonate reef oil reservoirs in northern Michigan in 1978 with Shell Oil Co.'s Chester 18 waterflood. Ten waterflood projects had been installed by Spring 1983. As a result of this experience, significant production technology practices have become established. The majority of the waterflood experience has been in Shell's Gaylord Production Unit located primarily in Otsego and Crawford counties. Specifically, the projects discussed are the Chester 18, Chester 21, Frederic 10, Hayes 15, Hayes 21A, and Mid-Charlton 10 waterfloods. In general, the waterflood program can be characterized by very favorable oil production response, timely and definitive surveillance techniques, systematic and timely well work on injectors and producers to maintain optimum reservoir withdrawal behavior, innovative application of artificial lift technology, and aggressive future planning to maintain and to improve oil production response. This paper elaborates on these waterflood program characterizations.

  17. Gas Hydrate Research Database and Web Dissemination Channel

    SciTech Connect (OSTI)

    Micheal Frenkel; Kenneth Kroenlein; V Diky; R.D. Chirico; A. Kazakow; C.D. Muzny; M. Frenkel

    2009-09-30T23:59:59.000Z

    To facilitate advances in application of technologies pertaining to gas hydrates, a United States database containing experimentally-derived information about those materials was developed. The Clathrate Hydrate Physical Property Database (NIST Standard Reference Database {number_sign} 156) was developed by the TRC Group at NIST in Boulder, Colorado paralleling a highly-successful database of thermodynamic properties of molecular pure compounds and their mixtures and in association with an international effort on the part of CODATA to aid in international data sharing. Development and population of this database relied on the development of three components of information-processing infrastructure: (1) guided data capture (GDC) software designed to convert data and metadata into a well-organized, electronic format, (2) a relational data storage facility to accommodate all types of numerical and metadata within the scope of the project, and (3) a gas hydrate markup language (GHML) developed to standardize data communications between 'data producers' and 'data users'. Having developed the appropriate data storage and communication technologies, a web-based interface for both the new Clathrate Hydrate Physical Property Database, as well as Scientific Results from the Mallik 2002 Gas Hydrate Production Research Well Program was developed and deployed at http://gashydrates.nist.gov.

  18. Evaluation of the Gas Production Potential of Marine Hydrate Deposits in the Ulleung Basin of the Korean East Sea

    E-Print Network [OSTI]

    Moridis, George J.; Reagan, Matthew T.; Kim, Se-Joon; Seol, Yongkoo; Zhang, Keni

    2007-01-01T23:59:59.000Z

    through the annular gravel pack (kg) N H = hydration numberthrough the annular gravel pack (kg/s) Q V = rate of CH 4the ocean through the annular gravel pack (ST m 3 ) X = mass

  19. Systematic Discrimination of Advanced Hydrogen Production Technologies

    SciTech Connect (OSTI)

    Charles V. Park; Michael W. Patterson

    2010-07-01T23:59:59.000Z

    The U.S. Department of Energy, in concert with industry, is developing a high-temperature gas-cooled reactor at the Idaho National Laboratory (INL) to demonstrate high temperature heat applications to produce hydrogen and electricity or to support other industrial applications. A key part of this program is the production of hydrogen from water that would significantly reduce carbon emissions compared to current production using natural gas. In 2009 the INL led the methodical evaluation of promising advanced hydrogen production technologies in order to focus future resources on the most viable processes. This paper describes how the evaluation process was systematically planned and executed. As a result, High-Temperature Steam Electrolysis was selected as the most viable near-term technology to deploy as a part of the Next Generation Nuclear Plant Project.

  20. 2012 Pathways to Commercial Success: Technologies and Products...

    Broader source: Energy.gov (indexed) [DOE]

    (emerging) technologies and products that benefited from the support of the Fuel Cell Technologies Office and its predecessor programs within DOE's Office of Energy...

  1. Buildings R&D Breakthroughs: Technologies and Products Supported...

    Broader source: Energy.gov (indexed) [DOE]

    rdbreakthroughs.pdf More Documents & Publications 2012 Pathways to Commercial Success: Technologies and Products Supported by the Fuel Cell Technologies Program 2011 Pathways to...

  2. 2009 Pathways to Commercial Success: Technologies and Products...

    Office of Environmental Management (EM)

    Pathways to Commercial Success: Technologies and Products Supported by the Hydrogen, Fuel Cells and Infrastructure Technologies Program 2009 Pathways to Commercial Success:...

  3. Handbook of gas hydrate properties and occurrence

    SciTech Connect (OSTI)

    Kuustraa, V.A.; Hammershaimb, E.C.

    1983-12-01T23:59:59.000Z

    This handbook provides data on the resource potential of naturally occurring hydrates, the properties that are needed to evaluate their recovery, and their production potential. The first two chapters give data on the naturally occurring hydrate potential by reviewing published resource estimates and the known and inferred occurrences. The third and fourth chapters review the physical and thermodynamic properties of hydrates, respectively. The thermodynamic properties of hydrates that are discussed include dissociation energies and a simplified method to calculate them; phase diagrams for simple and multi-component gases; the thermal conductivity; and the kinetics of hydrate dissociation. The final chapter evaluates the net energy balance of recovering hydrates and shows that a substantial positive energy balance can theoretically be achieved. The Appendices of the Handbook summarize physical and thermodynamic properties of gases, liquids and solids that can be used in designing and evaluating recovery processes of hydrates. 158 references, 67 figures, 47 tables.

  4. Simulations of Variable Bottomhole Pressure Regimes to Improve Production from the Double-Unit Mount Elbert, Milne Point Unit, North Slope Alaska Hydrate Deposit

    SciTech Connect (OSTI)

    Myshakin, Evgeniy; Anderson, Brian; Rose, Kelly; Boswell, Ray

    2011-01-01T23:59:59.000Z

    Gas production was predicted from a reservoir model based on the Mount Elbert gas hydrate accumulation located on the Alaska North slope at various simulator submodels and production scenarios. Log, core, and fluid measurements were used to provide a comprehensive reservoir description. These data were incorporated with experimentally derived saturations, porosities, permeability values, parameters for capillary pressure, and relative permeability functions. The modeled reservoir exposed to depressurization at a constant bottomhole pressure (2.7 MPa) has shown limited production potential due to its low temperature profile. To improve production the bottomhole pressure was allowed to vary from 2.7 (above the quadruple point) to 2.0 MPa over a 15-year period. The results indicate that gas production was nearly doubled in comparison with a constant-pressure regime. Extensive ice formation and hydrate reformation that could severely hinder gas production were avoided in the variable-pressure regime system. A use of permeability variation coupled with porosity change is shown to be crucial to predict those phenomena at a reservoir scale.

  5. The Research Path to Determining the Natural Gas Supply Potential of Marine Gas Hydrates

    SciTech Connect (OSTI)

    Boswell, R.M.; Rose, K.K.; Baker, R.C.

    2008-06-01T23:59:59.000Z

    A primary goal of the U.S. National Interagency Gas Hydrates R&D program is to determine the natural gas production potential of marine gas hydrates. In pursuing this goal, four primary areas of effort are being conducted in parallel. First, are wide-ranging basic scientific investigations in both the laboratory and in the field designed to advance the understanding of the nature and behavior of gas hydrate bearing sediments (GHBS). This multi-disciplinary work has wide-ranging direct applications to resource recovery, including assisting the development of exploration and production technologies through better rock physics models for GHBS and also in providing key data for numerical simulations of productivity, reservoir geomechanical response, and other phenomena. In addition, fundamental science efforts are essential to developing a fuller understanding of the role gas hydrates play in the natural environment and the potential environmental implications of gas hydrate production, a critical precursor to commercial extraction. A second area of effort is the confirmation of resource presence and viability via a series of multi-well marine drilling expeditions. The collection of data in the field is essential to further clarifying what proportion of the likely immense in-place marine gas hydrate resource exists in accumulations of sufficient quality to represent potential commercial production prospects. A third research focus area is the integration of geologic, geophysical, and geochemical field data into an effective suite of exploration tools that can support the delineation and characterization commercial gas hydrate prospects prior to drilling. The fourth primary research focus is the development and testing of well-based extraction technologies (including drilling, completion, stimulation and production) that can safely deliver commercial gas production rates from gas hydrate reservoirs in a variety of settings. Initial efforts will take advantage of the relatively favorable economics of conducting production tests in Arctic gas-hydrate bearing sandstones with the intent of translating the knowledge gained to later testing in marine sandstone reservoirs. The full and concurrent pusuit of each of these research topics is essential to the determining the future production potential of naturally-occuring gas hydrates.

  6. Solar and Wind Technologies for Hydrogen Production Report to Congress

    Fuel Cell Technologies Publication and Product Library (EERE)

    DOE's Solar and Wind Technologies for Hydrogen Production Report to Congress summarizes the technology roadmaps for solar- and wind-based hydrogen production. Published in December 2005, it fulfills t

  7. Hydrogen Production Roadmap: Technology Pathways to the Future, January 2009

    Fuel Cell Technologies Publication and Product Library (EERE)

    Roadmap to identify key challenges and priority R&D needs associated with various hydrogen fuel production technologies.

  8. Technologies for production of Electricity and Heat in Sweden

    E-Print Network [OSTI]

    Technologies for production of Electricity and Heat in Sweden Wind Energy ­ in perspective Morthorst December 2008 #12;Technologies for production of Electricity and Heat in Sweden Wind Energy Erik Morthorst Title: Technologies for production of Electricity and Heat in Sweden Wind Energy

  9. Technologies for Production of Heat and Electricity

    SciTech Connect (OSTI)

    Jacob J. Jacobson; Kara G. Cafferty

    2014-04-01T23:59:59.000Z

    Biomass is a desirable source of energy because it is renewable, sustainable, widely available throughout the world, and amenable to conversion. Biomass is composed of cellulose, hemicellulose, and lignin components. Cellulose is generally the dominant fraction, representing about 40 to 50% of the material by weight, with hemicellulose representing 20 to 50% of the material, and lignin making up the remaining portion [4,5,6]. Although the outward appearance of the various forms of cellulosic biomass, such as wood, grass, municipal solid waste (MSW), or agricultural residues, is different, all of these materials have a similar cellulosic composition. Elementally, however, biomass varies considerably, thereby presenting technical challenges at virtually every phase of its conversion to useful energy forms and products. Despite the variances among cellulosic sources, there are a variety of technologies for converting biomass into energy. These technologies are generally divided into two groups: biochemical (biological-based) and thermochemical (heat-based) conversion processes. This chapter reviews the specific technologies that can be used to convert biomass to energy. Each technology review includes the description of the process, and the positive and negative aspects.

  10. Solar and Wind Technologies for Hydrogen Production: Report to Congress Solar and Wind Technologies

    E-Print Network [OSTI]

    .........................5 1.4 Potential Capacity for Hydrogen Production from Conventional Electrolysis Using Wind and SolarSolar and Wind Technologies for Hydrogen Production: Report to Congress Solar and Wind Technologies For Hydrogen Production Report to Congress December 2005 (ESECS EE-3060) #12;Solar and Wind Technologies

  11. Development of Alaskan gas hydrate resources

    SciTech Connect (OSTI)

    Kamath, V.A.; Sharma, G.D.; Patil, S.L.

    1991-06-01T23:59:59.000Z

    The research undertaken in this project pertains to study of various techniques for production of natural gas from Alaskan gas hydrates such as, depressurization, injection of hot water, steam, brine, methanol and ethylene glycol solutions through experimental investigation of decomposition characteristics of hydrate cores. An experimental study has been conducted to measure the effective gas permeability changes as hydrates form in the sandpack and the results have been used to determine the reduction in the effective gas permeability of the sandpack as a function of hydrate saturation. A user friendly, interactive, menu-driven, numerical difference simulator has been developed to model the dissociation of natural gas hydrates in porous media with variable thermal properties. A numerical, finite element simulator has been developed to model the dissociation of hydrates during hot water injection process.

  12. Information Technology and Productivity: A Review of the Literature

    E-Print Network [OSTI]

    Information Technology and Productivity: A Review of the Literature Erik Brynjolfsson Shinkyu Yang for numerous valuable comments. #12;Information Technology and Productivity: A Review of the Literature Erik) and productivity became a source of debate: the astonishing improvements in computers' underlying capabilities

  13. Essays on productivity, technology, and economic fluctuations

    E-Print Network [OSTI]

    Christiansen, Lone Engbo

    2007-01-01T23:59:59.000Z

    BLDG & REPAIRING GENERAL ELECTRIC CO CONGLOMERATES GENERALUnited Technologies General Electric TRW Inc Honeywell Inc-United Technologies General Electric TRW Inc Honeywell Inc-

  14. Managing the integration of technology into the product development pipeline

    E-Print Network [OSTI]

    Barretto, Eduardo F., 1971-

    2005-01-01T23:59:59.000Z

    Managing the integration of technology is a complex task in any industry, but especially so in the highly competitive automotive industry. Automakers seek to develop plans to integrate technology into their products such ...

  15. Physical Properties of Gas Hydrates: A Review

    SciTech Connect (OSTI)

    Gabitto, Jorge [Prairie View A& M University; Tsouris, Costas [ORNL

    2010-01-01T23:59:59.000Z

    Methane gas hydrates in sediments have been studied by several investigators as a possible future energy resource. Recent hydrate reserves have been estimated at approximately 1016?m3 of methane gas worldwide at standard temperature and pressure conditions. In situ dissociation of natural gas hydrate is necessary in order to commercially exploit the resource from the natural-gas-hydrate-bearing sediment. The presence of gas hydrates in sediments dramatically alters some of the normal physical properties of the sediment. These changes can be detected by field measurements and by down-hole logs. An understanding of the physical properties of hydrate-bearing sediments is necessary for interpretation of geophysical data collected in field settings, borehole, and slope stability analyses; reservoir simulation; and production models. This work reviews information available in literature related to the physical properties of sediments containing gas hydrates. A brief review of the physical properties of bulk gas hydrates is included. Detection methods, morphology, and relevant physical properties of gas-hydrate-bearing sediments are also discussed.

  16. Conversion Technologies for Advanced Biofuels - Bio-Oil Production...

    Broader source: Energy.gov (indexed) [DOE]

    International report-out at the CTAB webinar on Conversion Technologies for Advanced Biofuels - Bio-Oil Production. ctabwebinarbiooilsproduction.pdf More Documents &...

  17. TEHNOMUS -New Technologies and Products in Machine Manufacturing Technologies" USING VIRTUAL PARTS TO OPTIMIZE THE METROLOGY

    E-Print Network [OSTI]

    Boyer, Edmond

    TEHNOMUS - New Technologies and Products in Machine Manufacturing Technologies" 9 USING VIRTUAL is a perfect perpendicular cylinder and all plane surfaces #12;TEHNOMUS - New Technologies and Products the dispersion of the position of different drilled holes (XYZ values in a coordinate system) when we change

  18. Strategies for gas production from oceanic Class 3 hydrateaccumulations

    SciTech Connect (OSTI)

    Moridis, George J.; Reagan, Matthew T.

    2007-05-01T23:59:59.000Z

    Gas hydrates are solid crystalline compounds in which gasmolecules are lodged within the lattices of ice crystals. Vast amounts ofCH4 are trapped in gas hydrates, and a significant effort has recentlybegun to evaluate hydrate deposits as a potential energy source. Class 3hydrate deposits are characterized by an isolated Hydrate-Bearing Layer(HBL) that is not in contact with any hydrate-free zone of mobile fluids.The base of the HBL in Class 3 deposits may occur within or at the edgeof the zone of thermodynamic hydrate stability.In this numerical study oflong-term gas production from typical representatives of unfracturedClass 3 deposits, we determine that simple thermal stimulation appears tobe a slow and inefficient production method. Electrical heating and warmwater injection result in very low production rates (4 and 12 MSCFD,respectively) that are orders of magnitude lower than generallyacceptable standards of commercial viability of gas production fromoceanic reservoirs. However, production from depressurization-baseddissociation based on a constant well pressure appears to be a promisingapproach even in deposits characterized by high hydrate saturations. Thisapproach allows the production of very large volumes ofhydrate-originating gas at high rates (>15 MMSCFD, with a long-termaverage of about 8.1 MMSCFD for the reference case) for long times usingconventional technology. Gas production from hydrates is accompanied by asignificant production of water. However, unlike conventional gasreservoirs, the water production rate declines with time. The lowsalinity of the produced water may require care in its disposal. Becauseof the overwhelming advantage of depressurization-based methods, thesensitivity analysis was not extendedto thermal stimulation methods. Thesimulation results indicate that depressurization-induced gas productionfrom oceanic Class 3 deposits increases (and the corresponding waterto-gas ratio decreases) with increasing hydrate temperature (whichdefines the hydrate stability), increasing intrinsic permeability of theHBL, and decreasing hydrate saturation although depletion of the hydratemay complicate the picture in the latter case.

  19. Pathways to Commercial Success: Technologies and Products Supported by the Fuel Cell Technologies Program

    Fuel Cell Technologies Publication and Product Library (EERE)

    This report identifies the commercial and near-commercial (emerging) hydrogen and fuel cell technologies and products that resulted from Department of Energy support through the Fuel Cell Technologies

  20. Sestar Technologies, LLC Revolutionar y Solar Energy Products

    E-Print Network [OSTI]

    Jawitz, James W.

    Sestar Technologies, LLC Revolutionar y Solar Energy Products Sestar Technologies, LLC (SESTAR) is developing revolutionary solar energy products that will be integral components in the ultimate solution to the world's current and future energy pro- grams. It will lead to paradigm shifts in a number of solar

  1. Production Well Performance Enhancement using Sonication Technology

    SciTech Connect (OSTI)

    Adewumi, Michael A; Ityokumbul, M Thaddeus; Watson, Robert W; Eltohami, Eltohami; Farias, Mario; Heckman, Glenn; Houlihan, Brendan; Karoor, Samata Prakash; Miller, Bruce G; Mohammed, Nazia; Olanrewaju, Johnson; Ozdemir, Mine; Rejepov, Dautmamed; Sadegh, Abdallah A; Quammie, Kevin E; Zaghloul, Jose; Hughes, W Jack; Montgomery, Thomas C

    2005-12-31T23:59:59.000Z

    The objective of this project was to develop a sonic well performance enhancement technology that focused on near wellbore formation damage. In order to successfully achieve this objective, a three-year project was defined. The entire project was broken into four tasks. The overall objective of all this was to foster a better understanding of the mechanisms involved in sonic energy interactions with fluid flow in porous media and adapt such knowledge for field applications. The fours tasks are: • Laboratory studies • Mathematical modeling • Sonic tool design and development • Field demonstration The project was designed to be completed in three years; however, due to budget cuts, support was only provided for the first year, and hence the full objective of the project could not be accomplished. This report summarizes what was accomplished with the support provided by the US Department of Energy. Experiments performed focused on determining the inception of cavitation, studying thermal dissipation under cavitation conditions, investigating sonic energy interactions with glass beads and oil, and studying the effects of sonication on crude oil properties. Our findings show that the voltage threshold for onset of cavitation is independent of transducer-hydrophone separation distance. In addition, thermal dissipation under cavitation conditions contributed to the mobilization of deposited paraffins and waxes. Our preliminary laboratory experiments suggest that waxes are mobilized when the fluid temperature approaches 40°C. Experiments were conducted that provided insights into the interactions between sonic wave and the fluid contained in the porous media. Most of these studies were carried out in a slim-tube apparatus. A numerical model was developed for simulating the effect of sonication in the nearwellbore region. The numerical model developed was validated using a number of standard testbed problems. However, actual application of the model for scale-up purposes was limited due to funding constraints. The overall plan for this task was to perlorm field trials with the sonication tooL These trials were to be performed in production and/or injection wells located in Pennsylvania, New York, and West Virginia. Four new wells were drilled in preparation for the field demonstration. Baseline production data were collected and reservoir simulator tuned to simulate these oil reservoirs. The sonication tools were designed for these wells. However, actual field testing could not be carried out because of premature termination of the project.

  2. air clathrate hydrates: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    the extent of hydration can be determined. In order to achieve this, development of a new pellet production method was essential. This technique facilitates the elimination of...

  3. Essays on productivity, technology, and economic fluctuations

    E-Print Network [OSTI]

    Christiansen, Lone Engbo

    2007-01-01T23:59:59.000Z

    BLDG & REPAIRING GENERAL ELECTRIC CO CONGLOMERATES GENERALINC GENERAL DYNAMICS CORP GENERAL ELECTRIC CO GENERAL MOTORSCo Northrop Grumman General Dynamics United Technologies General Electric

  4. Guest Molecule Exchange Kinetics for the 2012 Ignik Sikumi Gas Hydrate Field Trial

    SciTech Connect (OSTI)

    White, Mark D.; Lee, Won Suk

    2014-05-14T23:59:59.000Z

    A commercially viable technology for producing methane from natural gas hydrate reservoirs remains elusive. Short-term depressurization field tests have demonstrated the potential for producing natural gas via dissociation of the clathrate structure, but the long-term performance of the depressurization technology ultimately requires a heat source to sustain the dissociation. A decade of laboratory experiments and theoretical studies have demonstrated the exchange of pure CO2 and N2-CO2 mixtures with CH4 in sI gas hydrates, yielding critical information about molecular mechanisms, recoveries, and exchange kinetics. Findings indicated the potential for producing natural gas with little to no production of water and rapid exchange kinetics, generating sufficient interest in the guest-molecule exchange technology for a field test. In 2012 the U.S. DOE/NETL, ConocoPhillips Company, and Japan Oil, Gas and Metals National Corporation jointly sponsored the first field trial of injecting a mixture of N2-CO2 into a CH4-hydrate bearing formation beneath the permafrost on the Alaska North Slope. Known as the Ignik Sikumi #1 Gas Hydrate Field Trial, this experiment involved three stages: 1) the injection of a N2-CO2 mixture into a targeted hydrate-bearing layer, 2) a 4-day pressurized soaking period, and 3) a sustained depressurization and fluid production period. Data collected during the three stages of the field trial were made available after an extensive quality check. These data included continuous temperature and pressure logs, injected and recovered fluid compositions and volumes. The Ignik Sikumi #1 data set is extensive, but contains no direct evidence of the guest-molecule exchange process. This investigation is directed at using numerical simulation to provide an interpretation of the collected data. A numerical simulator, STOMP-HYDT-KE, was recently completed that solves conservation equations for energy, water, mobile fluid guest molecules, and hydrate guest molecules, for up to three gas hydrate guest molecules: CH4, CO2, and N2. The independent tracking of mobile fluid and hydrate guest molecules allows for the kinetic exchange of guest molecules between the mobile fluids and hydrate. The particular interest of this numerical investigation is to determine whether kinetic exchange parameters, determined from laboratory-scale experiments, are directly applicable to interpreting the Ignik Sikumi #1 data.

  5. Overview on Hydrate Coring, Handling and Analysis

    SciTech Connect (OSTI)

    Jon Burger; Deepak Gupta; Patrick Jacobs; John Shillinglaw

    2003-06-30T23:59:59.000Z

    Gas hydrates are crystalline, ice-like compounds of gas and water molecules that are formed under certain thermodynamic conditions. Hydrate deposits occur naturally within ocean sediments just below the sea floor at temperatures and pressures existing below about 500 meters water depth. Gas hydrate is also stable in conjunction with the permafrost in the Arctic. Most marine gas hydrate is formed of microbially generated gas. It binds huge amounts of methane into the sediments. Worldwide, gas hydrate is estimated to hold about 1016 kg of organic carbon in the form of methane (Kvenvolden et al., 1993). Gas hydrate is one of the fossil fuel resources that is yet untapped, but may play a major role in meeting the energy challenge of this century. In June 2002, Westport Technology Center was requested by the Department of Energy (DOE) to prepare a ''Best Practices Manual on Gas Hydrate Coring, Handling and Analysis'' under Award No. DE-FC26-02NT41327. The scope of the task was specifically targeted for coring sediments with hydrates in Alaska, the Gulf of Mexico (GOM) and from the present Ocean Drilling Program (ODP) drillship. The specific subjects under this scope were defined in 3 stages as follows: Stage 1: Collect information on coring sediments with hydrates, core handling, core preservation, sample transportation, analysis of the core, and long term preservation. Stage 2: Provide copies of the first draft to a list of experts and stakeholders designated by DOE. Stage 3: Produce a second draft of the manual with benefit of input from external review for delivery. The manual provides an overview of existing information available in the published literature and reports on coring, analysis, preservation and transport of gas hydrates for laboratory analysis as of June 2003. The manual was delivered as draft version 3 to the DOE Project Manager for distribution in July 2003. This Final Report is provided for records purposes.

  6. Methane Recovery from Hydrate-bearing Sediments

    SciTech Connect (OSTI)

    J. Carlos Santamarina; Costas Tsouris

    2011-04-30T23:59:59.000Z

    Gas hydrates are crystalline compounds made of gas and water molecules. Methane hydrates are found in marine sediments and permafrost regions; extensive amounts of methane are trapped in the form of hydrates. Methane hydrate can be an energy resource, contribute to global warming, or cause seafloor instability. This study placed emphasis on gas recovery from hydrate bearing sediments and related phenomena. The unique behavior of hydrate-bearing sediments required the development of special research tools, including new numerical algorithms (tube- and pore-network models) and experimental devices (high pressure chambers and micromodels). Therefore, the research methodology combined experimental studies, particle-scale numerical simulations, and macro-scale analyses of coupled processes. Research conducted as part of this project started with hydrate formation in sediment pores and extended to production methods and emergent phenomena. In particular, the scope of the work addressed: (1) hydrate formation and growth in pores, the assessment of formation rate, tensile/adhesive strength and their impact on sediment-scale properties, including volume change during hydrate formation and dissociation; (2) the effect of physical properties such as gas solubility, salinity, pore size, and mixed gas conditions on hydrate formation and dissociation, and it implications such as oscillatory transient hydrate formation, dissolution within the hydrate stability field, initial hydrate lens formation, and phase boundary changes in real field situations; (3) fluid conductivity in relation to pore size distribution and spatial correlation and the emergence of phenomena such as flow focusing; (4) mixed fluid flow, with special emphasis on differences between invading gas and nucleating gas, implications on relative gas conductivity for reservoir simulations, and gas recovery efficiency; (5) identification of advantages and limitations in different gas production strategies with emphasis; (6) detailed study of CH4-CO2 exchange as a unique alternative to recover CH4 gas while sequestering CO2; (7) the relevance of fines in otherwise clean sand sediments on gas recovery and related phenomena such as fines migration and clogging, vuggy structure formation, and gas-driven fracture formation during gas production by depressurization.

  7. Product Libraries Technology Review James Nyambayo and Ihsan Faraj

    E-Print Network [OSTI]

    Amor, Robert

    Product Libraries ­ Technology Review James Nyambayo and Ihsan Faraj Building Research reviews the development of the standards for access to external product libraries in relation to procurement and product data exchange. Procurement accounts for 70-85 % of the value of a build- ing project

  8. Rapid Gas Hydrate Formation Processes: Will They Work?

    SciTech Connect (OSTI)

    Brown, T.D.; Taylor, C.E.; Bernardo, M.P.

    2010-01-01T23:59:59.000Z

    Researchers at DOE’s National Energy Technology Laboratory (NETL) have been investigating the formation of synthetic gas hydrates, with an emphasis on rapid and continuous hydrate formation techniques. The investigations focused on unconventional methods to reduce dissolution, induction, nucleation and crystallization times associated with natural and synthetic hydrates studies conducted in the laboratory. Numerous experiments were conducted with various high-pressure cells equipped with instrumentation to study rapid and continuous hydrate formation. The cells ranged in size from 100 mL for screening studies to proof-of-concept studies with NETL’s 15-Liter Hydrate Cell. Results from this work demonstrate that the rapid and continuous formation of methane hydrate is possible at predetermined temperatures and pressures within the stability zone of a Methane Hydrate Stability Curve (see Figure 1).

  9. Rapid Gas Hydrate Formation Processes: Will They Work?

    DOE Public Access Gateway for Energy & Science Beta (PAGES Beta)

    Brown, Thomas D.; Taylor, Charles E.; Bernardo, Mark P.

    2010-06-01T23:59:59.000Z

    Researchers at DOE’s National Energy Technology Laboratory (NETL) have been investigating the formation of synthetic gas hydrates, with an emphasis on rapid and continuous hydrate formation techniques. The investigations focused on unconventional methods to reduce dissolution, induction, nucleation and crystallization times associated with natural and synthetic hydrates studies conducted in the laboratory. Numerous experiments were conducted with various high-pressure cells equipped with instrumentation to study rapid and continuous hydrate formation. The cells ranged in size from 100 mL for screening studies to proof-of-concept studies with NETL’s 15-Liter Hydrate Cell. Results from this work demonstrate that the rapid and continuous formationmore »of methane hydrate is possible at predetermined temperatures and pressures within the stability zone of a Methane Hydrate Stability Curve.« less

  10. Information, Technology, and Information Worker Productivity

    E-Print Network [OSTI]

    Aral, Sinan

    We econometrically evaluate information worker productivity at a midsize executive recruiting firm and assess whether the knowledge that workers accessed through their electronic communication networks enabled them to ...

  11. Buildings R&D Breakthroughs: Technologies and Products Supported by the Building Technologies Program

    SciTech Connect (OSTI)

    Weakley, Steven A.

    2012-04-15T23:59:59.000Z

    The purpose of the project described in this report is to identify and characterize commercially available products and emerging (near-commercial) technologies that benefited from the support of the Building Technologies Program (BTP) within the U.S. Department of Energy’s Office of Energy Efficiency and Renewable Energy. The investigation specifically focused on technology-oriented research and development (R&D) projects funded by BTP’s Emerging Technologies subprogram from 2005-2011.

  12. analysing production technology: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    analysing production technology First Page Previous Page 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Next Page Last Page Topic Index 1 Information...

  13. Photographic lens manufacturing and production technologies

    E-Print Network [OSTI]

    Kubaczyk, Daniel Mark

    2011-01-01T23:59:59.000Z

    An investigation was conducted to determine the methods and processes required for the manufacture of photographic objective lenses. Production of photographic lenses requires incredible precision in the melting, mixing, ...

  14. Hydration-dependent dynamic crossover phenomenon in protein hydration water

    E-Print Network [OSTI]

    Wang, Zhe

    The characteristic relaxation time ? of protein hydration water exhibits a strong hydration level h dependence. The dynamic crossover is observed when h is higher than the monolayer hydration level h[subscript c] =0.2–0.25 ...

  15. Methane Hydrate Field Program

    SciTech Connect (OSTI)

    None

    2013-12-31T23:59:59.000Z

    This final report document summarizes the activities undertaken and the output from three primary deliverables generated during this project. This fifteen month effort comprised numerous key steps including the creation of an international methane hydrate science team, determining and reporting the current state of marine methane hydrate research, convening an international workshop to collect the ideas needed to write a comprehensive Marine Methane Hydrate Field Research Plan and the development and publication of that plan. The following documents represent the primary deliverables of this project and are discussed in summary level detail in this final report. • Historical Methane Hydrate Project Review Report • Methane Hydrate Workshop Report • Topical Report: Marine Methane Hydrate Field Research Plan • Final Scientific/Technical Report

  16. Methane Hydrates: Major Energy Source for the Future or Wishful Thinking?

    SciTech Connect (OSTI)

    Thomas, Charles Phillip

    2001-09-01T23:59:59.000Z

    Methane hydrates are methane bearing, ice-like materials that occur in abundance in permafrost areas such as on the North Slope of Alaska and Canada and as well as in offshore continental margin environments throughout the world including the Gulf of Mexico and the East and West Coasts of the United States. Methane hydrate accumulations in the United States are currently estimated to be about 200,000 Tcf, which is enormous when compared to the conventional recoverable resource estimate of 2300 Tcf. On a worldwide basis, the estimate is 700,000 Tcf or about two times the total carbon in coal, oil and conventional gas in the world. The enormous size of this resource, if producible to any degree, has significant implications for U.S. and worldwide clean energy supplies and global environmental issues. Historically the petroleum industry's interests in methane hydrates have primarily been related to safety issues such as wellbore stability while drilling, seafloor stability, platform subsidence, and pipeline plugging. Many questions remain to be answered to determine if any of this potential energy resource is technically and economically viable to produce. Major technical hurdles include: 1) methods to find, characterize, and evaluate the resource; 2) technology to safely and economically produce natural gas from methane hydrate deposits; and 3) safety and seafloor stability issues related to drilling through gas hydrate accumulations to produce conventional oil and gas. The petroleum engineering profession currently deals with gas hydrates in drilling and production operations and will be key to solving the technical and economic problems that must be overcome for methane hydrates to be part of the future energy mix in the world.

  17. Depressurization-induced gas production from Class 1 hydratedeposits

    SciTech Connect (OSTI)

    Moridis, George J.; Kowalsky, Michael B.; Pruess, Karsten

    2005-11-01T23:59:59.000Z

    Class 1 hydrate deposits are characterized by ahydratebearing layer underlain by a two-phase zone involving mobile gas.Two kinds of deposits are investigated. The first involves water andhydrate in the hydrate zone (Class 1W), while the second involves gas andhydrate (Class 1G). We introduce new models to describe the effect of thepresence of hydrates on the wettability properties of porous media. Wedetermine that large volumes of gas can be readily produced at high ratesfor long times from Class 1 gas hydrate accumulations by means ofdepressurization-induced dissociation using conventional technology.Dissociation in Class 1W deposits proceeds in distinct stages, while itis continuous in Class 1G deposits. To avoid blockage caused by hydrateformation in the vicinity of the well, wellbore heating is a necessity inproduction from Class 1 hydrates. Class 1W hydrates are shown tocontribute up to 65 percent of the production rate and up to 45 percentof the cumulative volume of produced gas; the corresponding numbers forClass 1G hydrates are 75 percent and 54 percent. Production from bothClass 1W and Class 1G deposits leads to the emergence of a seconddissociation front (in addition to the original ascending hydrateinterface) that forms at the top of the hydrate interval and advancesdownward. Inboth kinds of deposits, capillary pressure effects lead tohydrate lensing, i.e., the emergence of distinct banded structures ofalternating high-low hydrate saturation, which form channels and shellsand have a significant effect on production.

  18. Pathways to Commercial Success: Technologies and Products Supported by the Fuel Cell Technologies Program - 2011

    Fuel Cell Technologies Publication and Product Library (EERE)

    This FY 2011 report updates the results of an effort to identify and characterize commercial and near-commercial (emerging) technologies and products that benefited from the support of the Fuel Cell

  19. Pathways to Commercial Success: Technologies and Products Supported by the Fuel Cell Technologies Program - 2012

    Fuel Cell Technologies Publication and Product Library (EERE)

    This FY 2012 report updates the results of an effort to identify and characterize commercial and near-commercial (emerging) technologies and products that benefited from the support of the Fuel Cell T

  20. Pathways to Commercial Success: Technologies and Products Supported by the Fuel Cell Technologies Office - 2013

    Fuel Cell Technologies Publication and Product Library (EERE)

    This FY 2013 report updates the results of an effort to identify and characterize commercial and near-commercial (emerging) technologies and products that benefited from the support of the Fuel Cell T

  1. Technology diffusion of energy-related products in residential markets

    SciTech Connect (OSTI)

    Davis, L.J.; Bruneau, C.L.

    1987-05-01T23:59:59.000Z

    Acceptance of energy-related technologies by end residential consumers, manufacturers of energy-related products, and other influential intermediate markets such as builders will influence the potential for market penetration of innovative energy-related technologies developed by the Department of Energy, Office of Building and Community Systems (OBCS). In this report, Pacific Northwest Laboratory reviewed the available information on technology adoption, diffusion, and decision-making processes to provide OBCS with a background and understanding of the type of research that has previously been conducted on this topic. Insight was gained as to the potential decision-making criteria and motivating factors that influence the decision-maker(s) selection of new technologies, and some of the barriers to technology adoption faced by potential markets for OBCS technologies.

  2. Coupled flow and geomechanical analysis for gas production in the Prudhoe Bay Unit L-106 well Unit C gas hydrate deposit in Alaska

    E-Print Network [OSTI]

    Kim, J.

    2014-01-01T23:59:59.000Z

    way Coupled Fluid Flow and Geomechanics in Hydrate Deposits.for Coupled Flow and Geomechanics. Soc. Pet. Eng. J. 16(2):for coupled flow and geomechanics: Drained and undrained

  3. Tools and Technology Article New Technology for Estimating Seed Production of

    E-Print Network [OSTI]

    Gray, Matthew

    in moist-soil wetlands. ( JOURNAL OF WILDLIFE MANAGEMENT 73(7):1229­1232; 2009) DOI: 10.2193/2008-468 KEY in moist-soil wetlands is one way to monitor succession and evaluate management (Gray et al. 1999c). ThusTools and Technology Article New Technology for Estimating Seed Production of Moist-Soil Plants

  4. An Overview of Hydrogen Production Technologies

    SciTech Connect (OSTI)

    Holladay, Jamie D.; Hu, Jianli; King, David L.; Wang, Yong

    2009-01-30T23:59:59.000Z

    Currently, hydrogen is primarily used in the chemical industry, but in the near future it will become a significant fuel. There are many processes for hydrogen production. This paper reviews reforming (steam, partial oxidation, autothermal, plasma, and aqueous phase), pyrolysis, hydrogen from biomass, electrolysis and other methods for generating hydrogen from water, and hydrogen storage. In addition, desulfurization, water-gas-shift, and hydrogen purification methods are discussed. Basics of these processes are presented with a large number of references for the interested reader to learn more.

  5. Products and Technologies | Department of Energy

    Office of Environmental Management (EM)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742 33 1112011 Strategic2 OPAM615_CostNSAR - TProcuring Solar for Federal FacilitiesProducts and

  6. Chemically reacting plumes, gas hydrate dissociation and dendrite solidification

    E-Print Network [OSTI]

    Conroy, Devin Thomas

    2008-01-01T23:59:59.000Z

    II Gas hydrates Introductionto gas hydrates . . . . . . . . . . 1.127 Gas hydrate dissociation in porous media . 1.

  7. University of Maine Integrated Forest Product Refinery (IFPR) Technology Research

    SciTech Connect (OSTI)

    Pendse, Hemant P.

    2010-11-23T23:59:59.000Z

    This project supported research on science and technology that forms a basis for integrated forest product refinery for co-production of chemicals, fuels and materials using existing forest products industry infrastructure. Clear systems view of an Integrated Forest Product Refinery (IFPR) allowed development of a compelling business case for a small scale technology demonstration in Old Town ME for co-production of biofuels using cellulosic sugars along with pulp for the new owners of the facility resulting in an active project on Integrated Bio-Refinery (IBR) at the Old Town Fuel & Fiber. Work on production of advanced materials from woody biomass has led to active projects in bioplastics and carbon nanofibers. A lease for 40,000 sq. ft. high-bay space has been obtained to establish a Technology Research Center for IFPR technology validation on industrially relevant scale. UMaine forest bioproducts research initiative that began in April 2006 has led to establishment of a formal research institute beginning in March 2010.

  8. A pilot-scale continuous-jet hydrate reactor

    SciTech Connect (OSTI)

    Szymcek, Phillip [ORNL; McCallum, Scott [Oak Ridge Associated Universities (ORAU); Taboada Serrano, Patricia L [ORNL; Tsouris, Costas [ORNL

    2008-01-01T23:59:59.000Z

    A three-phase, pilot-scale continuous-jet hydrate reactor (CJHR) has been developed for the production of gas hydrates. The reactor receives water and a hydrate-forming species to produce the solid gas hydrate. The CJHR has been tested for the production of CO{sub 2} hydrate for the purpose of ocean carbon sequestration. Formation of CO{sub 2} hydrate was investigated using various reactor/injector designs in a 72-l high-pressure vessel. Designs of the CJHR varied from single-capillary to multiple-capillary injectors that dispersed (1) liquid CO{sub 2} into water or (2) water into liquid CO{sub 2}. The novel injector is designed to improve the dispersion of one reactant into the other and, thus, eliminate mass transfer barriers that negatively affect conversion. An additional goal was an increase in production rates of two orders of magnitude. The designed injectors were tested in both distilled and saline water. Hydrate production experiments were conducted at different CO{sub 2} and water flow rates and for pressures and temperatures equivalent to intermediate ocean depths (1100-1700 m). The pilot-scale reactor with the novel injection system successfully increased hydrate production rates and efficiency.

  9. Prototyping of a real size air-conditioning system using a tetra-n-butylammonium bromide semiclathrate hydrate slurry as secondary two-phase refrigerant

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    semiclathrate hydrate slurry as secondary two-phase refrigerant ­ Experimental investigations and modelling). Abstract Among innovative processes developed in the field of refrigeration systems, technologies) is used as secondary refrigerant. The production of the slurry can be smoothed over day and night. Upon

  10. Innovative applications of technology for nuclear power plant productivity improvements

    SciTech Connect (OSTI)

    Naser, J. A. [Electric Power Research Inst., 3420 Hillview Avenue, Palo Alto, CA 94303 (United States)

    2012-07-01T23:59:59.000Z

    The nuclear power industry in several countries is concerned about the ability to maintain high plant performance levels due to aging and obsolescence, knowledge drain, fewer plant staff, and new requirements and commitments. Current plant operations are labor-intensive due to the vast number of operational and support activities required by commonly used technology in most plants. These concerns increase as plants extend their operating life. In addition, there is the goal to further improve performance while reducing human errors and increasingly focus on reducing operations and maintenance costs. New plants are expected to perform more productively than current plants. In order to achieve and increase high productivity, it is necessary to look at innovative applications of modern technologies and new concepts of operation. The Electric Power Research Inst. is exploring and demonstrating modern technologies that enable cost-effectively maintaining current performance levels and shifts to even higher performance levels, as well as provide tools for high performance in new plants. Several modern technologies being explored can provide multiple benefits for a wide range of applications. Examples of these technologies include simulation, visualization, automation, human cognitive engineering, and information and communications technologies. Some applications using modern technologies are described. (authors)

  11. Method for controlling clathrate hydrates in fluid systems

    DOE Patents [OSTI]

    Sloan, Jr., Earle D. (Golden, CO)

    1995-01-01T23:59:59.000Z

    Discussed is a process for preventing clathrate hydrate masses from impeding the flow of fluid in a fluid system. An additive is contacted with clathrate hydrate masses in the system to prevent those clathrate hydrate masses from impeding fluid flow. The process is particularly useful in the natural gas and petroleum production, transportation and processing industry where gas hydrate formation can cause serious problems. Additives preferably contain one or more five member and/or six member cyclic chemical groupings. Additives include poly(N-vinyl-2-pyrrolidone) and hydroxyethylcellulose, either in combination or alone.

  12. Development of Alaskan gas hydrate resources. Final report

    SciTech Connect (OSTI)

    Kamath, V.A.; Sharma, G.D.; Patil, S.L.

    1991-06-01T23:59:59.000Z

    The research undertaken in this project pertains to study of various techniques for production of natural gas from Alaskan gas hydrates such as, depressurization, injection of hot water, steam, brine, methanol and ethylene glycol solutions through experimental investigation of decomposition characteristics of hydrate cores. An experimental study has been conducted to measure the effective gas permeability changes as hydrates form in the sandpack and the results have been used to determine the reduction in the effective gas permeability of the sandpack as a function of hydrate saturation. A user friendly, interactive, menu-driven, numerical difference simulator has been developed to model the dissociation of natural gas hydrates in porous media with variable thermal properties. A numerical, finite element simulator has been developed to model the dissociation of hydrates during hot water injection process.

  13. Coalbed Methane Procduced Water Treatment Using Gas Hydrate Formation at the Wellhead

    SciTech Connect (OSTI)

    BC Technologies

    2009-12-30T23:59:59.000Z

    Water associated with coalbed methane (CBM) production is a significant and costly process waste stream, and economic treatment and/or disposal of this water is often the key to successful and profitable CBM development. In the past decade, advances have been made in the treatment of CBM produced water. However, produced water generally must be transported in some fashion to a centralized treatment and/or disposal facility. The cost of transporting this water, whether through the development of a water distribution system or by truck, is often greater than the cost of treatment or disposal. To address this economic issue, BC Technologies (BCT), in collaboration with Oak Ridge National Laboratory (ORNL) and International Petroleum Environmental Consortium (IPEC), proposed developing a mechanical unit that could be used to treat CBM produced water by forming gas hydrates at the wellhead. This process involves creating a gas hydrate, washing it and then disassociating hydrate into water and gas molecules. The application of this technology results in three process streams: purified water, brine, and gas. The purified water can be discharged or reused for a variety of beneficial purposes and the smaller brine can be disposed of using conventional strategies. The overall objectives of this research are to develop a new treatment method for produced water where it could be purified directly at the wellhead, to determine the effectiveness of hydrate formation for the treatment of produced water with proof of concept laboratory experiments, to design a prototype-scale injector and test it in the laboratory under realistic wellhead conditions, and to demonstrate the technology under field conditions. By treating the water on-site, producers could substantially reduce their surface handling costs and economically remove impurities to a quality that would support beneficial use. Batch bench-scale experiments of the hydrate formation process and research conducted at ORNL confirmed the feasibility of the process. However, researchers at BCT were unable to develop equipment suitable for continuous operation and demonstration of the process in the field was not attempted. The significant achievements of the research area: Bench-scale batch results using carbon dioxide indicate >40% of the feed water to the hydrate formation reactor was converted to hydrate in a single pass; The batch results also indicate >23% of the feed water to the hydrate formation reactor (>50% of the hydrate formed) was converted to purified water of a quality suitable for discharge; Continuous discharge and collection of hydrates was achieved at atmospheric pressure. Continuous hydrate formation and collection at atmospheric conditions was the most significant achievement and preliminary economics indicate that if the unit could be made operable, it is potentially economic. However, the inability to continuously separate the hydrate melt fraction left the concept not ready for field demonstration and the project was terminated after Phase Two research.

  14. THE PULTRUSION TECHNOLOGY FOR THE PRODUCTION OF FABRIC-CEMENT

    E-Print Network [OSTI]

    Mobasher, Barzin

    THE PULTRUSION TECHNOLOGY FOR THE PRODUCTION OF FABRIC-CEMENT COMPOSITES Alva Peled Structural Engineering, Arizona State University, USA #12;Advantages of Fabrics in Cement Composites 0 300 600 900 0 2 4 6 8 Deflection, mm FlexuralLoad,N Fabrics Continuous Fibers Cement Matrix #12;Fabrics

  15. IBM System Storage Product Guide IBM Systems and Technology Group

    E-Print Network [OSTI]

    IBM System Storage Product Guide IBM Systems and Technology Group #12;2 Today, information has, reduce storage and archiving costs and enable continuous access to information in support of business requirements. Learn more about IBM Information Infrastructure, including the full range of data storage

  16. X-ray Scanner for ODP Leg 204: Drilling Gas Hydrates on Hydrate Ridge, Cascadia Continental Margin

    E-Print Network [OSTI]

    Freifeld, Barry; Kneafsey, Tim; Pruess, Jacob; Reiter, Paul; Tomutsa, Liviu

    2002-01-01T23:59:59.000Z

    International Conference of Gas Hydrates, Yokohama, Japan.Prospectus, Drilling Gas Hydrates On Hydrate Ridge, CascadiaLeg 204: Drilling Gas Hydrates on Hydrate Ridge, Cascadia

  17. GULF OF MEXICO SEAFLOOR STABILITY AND GAS HYDRATE MONITORING STATION PROJECT

    SciTech Connect (OSTI)

    J. Robert Woolsey; Thomas M. McGee; Robin C. Buchannon

    2004-11-01T23:59:59.000Z

    The gas hydrates research Consortium (HRC), established and administered at the University if Mississippi's Center for Marine Research and Environmental Technology (CMRET) has been active on many fronts in FY 03. Extension of the original contract through March 2004, has allowed completion of many projects that were incomplete at the end of the original project period due, primarily, to severe weather and difficulties in rescheduling test cruises. The primary objective of the Consortium, to design and emplace a remote sea floor station for the monitoring of gas hydrates in the Gulf of Mexico by the year 2005 remains intact. However, the possibility of levering HRC research off of the Joint Industries Program (JIP) became a possibility that has demanded reevaluation of some of the fundamental assumptions of the station format. These provisions are discussed in Appendix A. Landmark achievements of FY03 include: (1) Continuation of Consortium development with new researchers and additional areas of research contribution being incorporated into the project. During this period, NOAA's National Undersea Research Program's (NURP) National Institute for Undersea Science and Technology (NIUST) became a Consortium funding partner, joining DOE and Minerals Management Service (MMS); (2) Very successful annual and semiannual meetings in Oxford Mississippi in February and September, 2003; (3) Collection of piston cores from MC798 in support of the effort to evaluate the site for possible monitoring station installation; (4) Completion of the site evaluation effort including reports of all localities in the northern Gulf of Mexico where hydrates have been documented or are strongly suspected to exist on the sea floor or in the shallow subsurface; (5) Collection and preliminary evaluation of vent gases and core samples of hydrate from sites in Green Canyon and Mississippi Canyon, northern Gulf of Mexico; (6) Monitoring of gas activity on the sea floor, acoustically and thermally; (7) Design, construction, and successful deployment of an in situ pore-water sampling device; (8) Improvements to the original Raman spectrometer (methane sensor); (9) Laboratory demonstration of the impact of bacterially-produced surfactants' rates of hydrate formation; (10) Construction and sea floor emplacement and testing--with both watergun and ship noise sources--of the prototypal vertical line array (VLA); (11) Initiation of studies of spatial controls on hydrates; (12) Compilation and analyses of seismic data, including mapping of surface anomalies; (13) Additional field verification (bottom samples recovered), in support of the site selection effort; (14) Collection and preliminary analyses of gas hydrates from new sites that exhibit variant structures; (15) Initial shear wave tests carried out in shallow water; (16) Isolation of microbes for potential medicinal products development; (17) Preliminary modeling of occurrences of gas hydrates.

  18. Assessment of the magnesium primary production technology. Final report

    SciTech Connect (OSTI)

    Flemings, M.C.; Kenney, G.B.; Sadoway, D.R.; Clark, J.P.; Szekely, J.

    1981-02-01T23:59:59.000Z

    At current production levels, direct energy savings achievable in primary magnesium production are 1.2 milliquads of energy per annum. Were magnesium to penetrate the automotive market to an average level of 50 pounds per vehicle, the resultant energy savings at the production stage would be somewhat larger, but the resulting savings in gasoline would conserve an estimated 325 milliquads of energy per year. The principal barrier to more widespread use of magnesium in the immediate future is its price. A price reduction of magnesium of 10% would lead to widespread conversion of aluminum die and permanent mold castings to magnesium. This report addresses the technology of electrolytic and thermic magnesium production and the economics of expanded magnesium production and use.

  19. (GAS HYDRATES) 2 ()

    E-Print Network [OSTI]

    : ... ... .... .... «» , 28 2007 : « » #12; · ·· #12; 2 #12; (GAS HYDRATES) #12;Y · µ 2 µ () µ · µ µ · µ µ µ ·µ: - - µ CO2 - - #12; - 3S·2M·1L·34H3S

  20. Marine electromagnetic methods for gas hydrate characterization

    E-Print Network [OSTI]

    Weitemeyer, Karen Andrea

    2008-01-01T23:59:59.000Z

    1.2 Gas Hydrates . . . . . . . .1.2.1 Distribution of Gas Hydrates . . . . . . . . . . .1.2.2 Importance of Gas Hydrates . . . . .

  1. Marine Electromagnetic Methods for Gas Hydrate Characterization

    E-Print Network [OSTI]

    Weitemeyer, Karen A

    2008-01-01T23:59:59.000Z

    1.2 Gas Hydrates . . . . . . . .1.2.1 Distribution of Gas Hydrates . . . . . . . . . . .1.2.2 Importance of Gas Hydrates . . . . .

  2. Geomechanical Performance of Hydrate-Bearing Sediment in Offshore Environments

    SciTech Connect (OSTI)

    Stephen Holditch; Tad Patzek; Jonny Rutqvist; George Moridis; Richard Plumb

    2008-03-31T23:59:59.000Z

    The objective of this multi-year, multi-institutional research project was to develop the knowledge base and quantitative predictive capability for the description of geomechanical performance of hydrate-bearing sediments (hereafter referred to as HBS) in oceanic environments. The focus was on the determination of the envelope of hydrate stability under conditions typical of those related to the construction and operation of offshore platforms. We have developed a robust numerical simulator of hydrate behavior in geologic media by coupling a reservoir model with a commercial geomechanical code. We also investigated the geomechanical behavior of oceanic HBS using pore-scale models (conceptual and mathematical) of fluid flow, stress analysis, and damage propagation. The objective of the UC Berkeley work was to develop a grain-scale model of hydrate-bearing sediments. Hydrate dissociation alters the strength of HBS. In particular, transformation of hydrate clusters into gas and liquid water weakens the skeleton and, simultaneously, reduces the effective stress by increasing the pore pressure. The large-scale objective of the study is evaluation of geomechanical stability of offshore oil and gas production infrastructure. At Lawrence Berkeley National Laboratory (LBNL), we have developed the numerical model TOUGH + Hydrate + FLAC3D to evaluate how the formation and disassociation of hydrates in seafloor sediments affects seafloor stability. Several technical papers were published using results from this model. LBNL also developed laboratory equipment and methods to produce realistic laboratory samples of sediments containing gas hydrates so that mechanical properties could be measured in the laboratory. These properties are required to run TOUGH + Hydrate + FLAC3D to evaluate seafloor stability issues. At Texas A&M University we performed a detailed literature review to determine what gas hydrate formation properties had been measured and reported in the literature. We then used TOUGH + Hydrate to simulate the observed gas production and reservoir pressure field data at Messoyakha. We simulated various scenarios that help to explain the field behavior. We have evaluated the effect of reservoir parameters on gas recovery from hydrates. Our work should be beneficial to others who are investigating how to produce gas from a hydrate capped gas reservoir. The results also can be used to better evaluate the process of producing gas from offshore hydrates. The Schlumberger PETREL model is used in industry to the description of geologic horizons and the special distribution of properties. An interface between FLAC3D and Petrel was built by Schlumberger to allow for efficient data entry into TOUGH + Hydrate + FLAC3D.

  3. Leaching of Phase II Mercury Control Technology By-Products

    SciTech Connect (OSTI)

    Hesbach, P.A.; Kachur, E.K.

    2007-07-01T23:59:59.000Z

    The U.S. EPA has issued a final regulation for control of mercury from coal-fired power plants. An NETL research, development and demonstration program under DOE/Fossil Energy Innovations for Existing Plants is directed toward the improvement of the performance and economics of mercury control from coal-fired plants. The current Phase II of the RD&D program emphasizes the evaluation of performance and cost of control technologies through slip-stream and full scale field testing while continuing the development of novel concepts. One of the concerns of the NETL program is the fate of the captured flue gas mercury which is transferred to the condensed phase by-product stream. These adulterated by-products, both ashes and FGD material, represent the greatest challenge to the DOE goal of increased utilization of by-products. The degree of stability of capture by-products and their potential for release of mercury can have a large economic impact on material sales or the approach to disposal. One of the considerations for mercury control technology is the potential trade-off between effective but temporary mercury capture and less effective but more permanent sequestration. As part of a greater characterization effort of Phase II facility baseline and control technology sample pairs, NETL in-house laboratories have performed aqueous leaching procedures on a select subset of the available sample pairs. This report describes batch leaching results for mercury, arsenic, and selenium.

  4. Western oil-shale development: a technology assessment. Volume 2: technology characterization and production scenarios

    SciTech Connect (OSTI)

    Not Available

    1982-01-01T23:59:59.000Z

    A technology characterization of processes that may be used in the oil shale industry is presented. The six processes investigated are TOSCO II, Paraho Direct, Union B, Superior, Occidental MIS, and Lurgi-Ruhrgas. A scanario of shale oil production to the 300,000 BPD level by 1990 is developed. (ACR)

  5. Imaging Hydrated Microbial Extracellular Polymers: Comparative...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Hydrated Microbial Extracellular Polymers: Comparative Analysis by Electron Microscopy . Imaging Hydrated Microbial Extracellular Polymers: Comparative Analysis by Electron...

  6. Toward Production From Gas Hydrates: Current Status, Assessment of Resources, and Simulation-Based Evaluation of Technology and Potential

    E-Print Network [OSTI]

    Moridis, George J.

    2008-01-01T23:59:59.000Z

    Assessment of U.S. Oil and Gas Resources (on CD-ROM) (limited conventional oil and gas resources (Boswell, 2007).for conventional oil and gas resources (Collett, 2004)

  7. Toward Production From Gas Hydrates: Current Status, Assessment of Resources, and Simulation-Based Evaluation of Technology and Potential

    E-Print Network [OSTI]

    Moridis, George J.

    2008-01-01T23:59:59.000Z

    through the annular gravel pack (kg/s) radius of the wellthrough the annular gravel pack (ST m 3 ) Greek Symbols ? =

  8. Toward Production From Gas Hydrates: Current Status, Assessment of Resources, and Simulation-Based Evaluation of Technology and Potential

    E-Print Network [OSTI]

    Moridis, George J.

    2008-01-01T23:59:59.000Z

    Assessment of U.S. Oil and Gas Resources (on CD-ROM) (Petroleum Geology, Atlas of Oil and Gas Fields, Structuraland logging conventional oil and gas wells. The ability to

  9. MANAGING SHORT-LIFECYCLE TECHNOLOGY PRODUCTS FOR AGERE S. David Wu

    E-Print Network [OSTI]

    Wu, David

    MANAGING SHORT-LIFECYCLE TECHNOLOGY PRODUCTS FOR AGERE SYSTEMS S. David Wu Department of Industrial demands for short-lifecycle technology products. Agere is particularly interested in using demand the leading indicator approach to various planning functions. Key words: Short-Lifecycle Technology Products

  10. Pathways to Commercial Success: Technologies and Products Supported by the Fuel Cell Technologies Program

    SciTech Connect (OSTI)

    Weakley, Steven A.

    2012-09-28T23:59:59.000Z

    The purpose of the project described in this report is to identify and document the commercial and emerging (projected to be commercialized within the next 3 years) hydrogen and fuel cell technologies and products that resulted from Department of Energy support through the Fuel Cell Technologies (FCT) Program in the Office of Energy Efficiency and Renewable Energy (EERE). Pacific Northwest National Laboratory (PNNL) undertook two efforts simultaneously to accomplish this project. The first effort was a patent search and analysis to identify patents related to hydrogen and fuel cells that are associated with FCT-funded projects (or projects conducted by DOE-EERE predecessor programs) and to ascertain the patents’ current status, as well as any commercial products that may have used the technology documented in the patent. The second effort was a series of interviews with current and past FCT personnel, a review of relevant program annual reports, and an examination of grants made under the Small Business Innovation Research and Small Business Technology Transfer Programs that are related to hydrogen and fuel cells.

  11. Pathways to Commercial Success: Technologies and Products Supported by the Fuel Cell Technologies Program

    SciTech Connect (OSTI)

    Weakley, Steven A.; Brown, Scott A.

    2011-09-29T23:59:59.000Z

    The purpose of the project described in this report is to identify and document the commercial and emerging (projected to be commercialized within the next 3 years) hydrogen and fuel cell technologies and products that resulted from Department of Energy support through the Fuel Cell Technologies (FCT) Program in the Office of Energy Efficiency and Renewable Energy (EERE). To do this, Pacific Northwest National Laboratory (PNNL) undertook two efforts simultaneously to accomplish this project. The first effort was a patent search and analysis to identify hydrogen- and fuel-cell-related patents that are associated with FCT-funded projects (or projects conducted by DOE-EERE predecessor programs) and to ascertain the patents current status, as well as any commercial products that may have used the technology documented in the patent. The second effort was a series of interviews with current and past FCT personnel, a review of relevant program annual reports, and an examination of hydrogen- and fuel-cell-related grants made under the Small Business Innovation Research and Small Business Technology Transfer Programs, and within the FCT portfolio.

  12. Carbonation Behavior of Pure Cement Hydrates under Supercritical Carbon Dioxide Conditions - 12199

    SciTech Connect (OSTI)

    Hirabayashi, Daisuke; Enokida, Youichi [Graduate School of Engineering, Nagoya University, 1 Furo-cho, Chikusa-ku, Nagoya-shi, Aichi-ken, 464-8603 (Japan); Sawada, Kayo [EcoTopia Science Institute, Nagoya University, 1 Furo-cho, Chikusa-ku, Nagoya-shi, Aichi-ken, 464-8603 (Japan); Hertz, Audrey; Charton, Frederic [CEA, DEN, Marcoule, DTCD/SPDE/L2ED, BP 17171, F-30207 Bagnols-sur-Ceze (France); Frizon, Fabien [CEA, DEN, Marcoule, DTCD/SPDE/LFSM, BP 17171, F-30207 Bagnols-sur-Ceze (France); Brouno, Fournel [CEA, DEN, Marcoule, DTCD, BP 17171, F-30207 Bagnols-sur-Ceze (France)

    2012-07-01T23:59:59.000Z

    Carbonation of cement-based waste forms using a supercritical carbon dioxide (SCCO{sub 2}) is a developing technology for the waste immobilization of radioactive and non-radioactive wastes. However, the detail carbonation behaviors of cement matrices under the SCCO{sub 2} condition are unknown, since cement matrices forms very complex phases. In this study, in order to clarify the crystal phases, we synthesized pure cement hydrate phases as each single phases; portlandite (Ca(OH){sub 2}), ettringite (Ca{sub 6}Al{sub 2}(SO{sub 4}){sub 3}(OH){sub 12}.26H{sub 2}O), and calcium silicate hydrate (n CaO---m SiO{sub 2} ---x H{sub 2}O), using suspensions containing a stoichiometric mixture of chemical regents, and performed carbonation experiments using an autoclave under supercritical condition for carbon dioxide. The XRD results revealed both the carbonate phases and co-product phases depending on the initial hydrate phases; gypsum for Ettringite, amorphous or crystalline silica for calcium silicate hydroxide. Thermogravimetric analysis was also performed to understand carbonation behaviors quantitatively. According to the experimental results, it was found that the major reaction was formation of calcium carbonate (CaCO{sub 3}) in all cases. However, the behaviors of H{sub 2}O and CO{sub 2} content were quietly different: Portlandite was most reactive for carbonation under SCCO{sub 2} conditions, and the CO{sub 2} content per one molar CaO was ranged from 0.96 ? 0.98. In the case of Ettringite, the experiment indicates partial decomposition of ettringite phase during carbonation. Ettringite was comparatively stable even under the SCCO{sub 2} conditions. Therefore, a part of ettringite remained and formed similar phases after the ettringite carbonation. The CO{sub 2} content for ettringite showed almost constant values around 0.86 ? 0.87. In the case of calcium silicate hydrate, the carbonation behavior was significantly influenced by the condition of SCCO{sub 2}. The CO{sub 2} content for the calcium silicate hydrate had values that ranged from 0.51 ? 1.01. The co-products of the carbonation were gypsum (CaSO{sub 4}) for ettringite, silica gel (SiO{sub x}) and silica (SiO{sub 2}) for calcium silicate hydrate, which also contributed to the densification of the particles. The production of co-products enhanced the change to their morphology after the carbonation. (authors)

  13. Experimental and Numerical Observations of Hydrate Reformation during Depressurization in a Core-Scale Reactor

    SciTech Connect (OSTI)

    Seol, Yongkoo; Myshakin, Evgeniy

    2011-01-01T23:59:59.000Z

    Gas hydrate has been predicted to reform around a wellbore during depressurization-based gas production from gas hydrate-bearing reservoirs. This process has an adverse effect on gas production rates and it requires time and sometimes special measures to resume gas flow to producing wells. Due to lack of applicable field data, laboratory scale experiments remain a valuable source of information to study hydrate reformation. In this work, we report laboratory experiments and complementary numerical simulations executed to investigate the hydrate reformation phenomenon. Gas production from a pressure vessel filled with hydrate-bearing sand was induced by depressurization with and without heat flux through the boundaries. Hydrate decomposition was monitored with a medical X-ray CT scanner and pressure and temperature measurements. CT images of the hydrate-bearing sample were processed to provide 3-dimensional data of heterogeneous porosity and phase saturations suitable for numerical simulations. In the experiments, gas hydrate reformation was observed only in the case of no-heat supply from surroundings, a finding consistent with numerical simulation. By allowing gas production on either side of the core, numerical simulations showed that initial hydrate distribution patterns affect gas distribution and flow inside the sample. This is a direct consequence of the heterogeneous pore network resulting in varying hydraulic properties of the hydrate-bearing sediment.

  14. Renewable and Appropriate Energy Laboratory Report Review of Technologies for the Production and Use of Charcoal

    E-Print Network [OSTI]

    Kammen, Daniel M.

    of Charcoal Production __________________________________5 The Petroleum LinkRenewable and Appropriate Energy Laboratory Report Review of Technologies for the Production areas. The production, transport and combustion of charcoal constitutes a critical energy and economic

  15. Drilling through gas hydrates formations: possible problems and suggested solution

    E-Print Network [OSTI]

    Amodu, Afolabi Ayoola

    2009-05-15T23:59:59.000Z

    .2.3 Case 310 This is the case of a gas hydrate buildup problem in a subsea christmas tree. The problem was that of a typical Campos Basin subsea well (1971.78ft water depth, 8oC at seabed) producing to a submarine production manifold on the seabed... ................................................................................. 14 2.3 Wellbore sketch for Case 2 ................................................................................. 17 2.4 Localization of gas hydrate in tree cap................................................................ 19 2.5a ROV...

  16. Application Specific Performance Technology for Productive Parallel Computing

    SciTech Connect (OSTI)

    Allen D. Malony; Sameer Shende

    2008-10-01T23:59:59.000Z

    Our accomplishments over the last three years of the DOE pro ject â??Application-Specific Perfor- mance Technology for Productive Parallel Computingâ? (DOE Agreement: DE-FG02-05ER25680) are described below. The pro ject will have met all of its ob jectives by the time of its completion at the end of September, 2008. Two extensive yearly progress reports were produced in in March 2006 and 2007 and were previously submitted to the DOE Oï¬?ce of Advanced Scientific Computing Research (OASCR). Following an overview of the ob jectives of the pro ject, we summarize for each of the pro ject areas the achievements in the first two years, and then describe in some more detail the pro ject accomplishments this past year. At the end, we discuss the relationship of the proposed renewal application to the work done on the current pro ject.

  17. Rapid gas hydrate formation process

    DOE Patents [OSTI]

    Brown, Thomas D.; Taylor, Charles E.; Unione, Alfred J.

    2013-01-15T23:59:59.000Z

    The disclosure provides a method and apparatus for forming gas hydrates from a two-phase mixture of water and a hydrate forming gas. The two-phase mixture is created in a mixing zone which may be wholly included within the body of a spray nozzle. The two-phase mixture is subsequently sprayed into a reaction zone, where the reaction zone is under pressure and temperature conditions suitable for formation of the gas hydrate. The reaction zone pressure is less than the mixing zone pressure so that expansion of the hydrate-forming gas in the mixture provides a degree of cooling by the Joule-Thompson effect and provides more intimate mixing between the water and the hydrate-forming gas. The result of the process is the formation of gas hydrates continuously and with a greatly reduced induction time. An apparatus for conduct of the method is further provided.

  18. Gas hydrate cool storage system

    DOE Patents [OSTI]

    Ternes, M.P.; Kedl, R.J.

    1984-09-12T23:59:59.000Z

    The invention presented relates to the development of a process utilizing a gas hydrate as a cool storage medium for alleviating electric load demands during peak usage periods. Several objectives of the invention are mentioned concerning the formation of the gas hydrate as storage material in a thermal energy storage system within a heat pump cycle system. The gas hydrate was formed using a refrigerant in water and an example with R-12 refrigerant is included. (BCS)

  19. TRACER DETECTION TECHNOLOGY CORP. PRODUCTS AND SERVICES FOR CORPORATE...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    by Dr. Arthur A. Ezra in his article, "Technology Utilization: Incentives and Solar Energy" which appeared in the February 28, 1975 edition of Science Magazine. The technology...

  20. Advanced Electrochemical Technologies for Hydrogen Production by Alternative Thermochemical Cycles

    SciTech Connect (OSTI)

    The Pennsylvania State Univeristy: Serguei Lvov, Mike Chung, Mark Fedkin, Victor Balashov, Elena, Chalkova, Nikolay Akinfiev; University of South Carolina: Carol Stork, Thomas Davis, Francis Gadala-Maria, Thomas Stanford, John Weidner; Tulane University: Victor Law, John Prindle; Lewis, ANL: Michele

    2011-01-06T23:59:59.000Z

    Hydrogen fuel is a potentially major solution to the problem of climate change, as well as addressing urban air pollution issues. But a key future challenge for hydrogen as a clean energy carrier is a sustainable, low-cost method of producing it in large capacities. Most of the world�s hydrogen is currently derived from fossil fuels through some type of reforming processes. Nuclear hydrogen production is an emerging and promising alternative to the reforming processes for carbon-free hydrogen production in the future. This report presents the main results of a research program carried out by a NERI Consortium, which consisted of Penn State University (PSU) (lead), University of South Carolina (USC), Tulane University (TU), and Argonne National Laboratory (ANL). Thermochemical water decomposition is an emerging technology for large-scale production of hydrogen. Typically using two or more intermediate compounds, a sequence of chemical and physical processes split water into hydrogen and oxygen, without releasing any pollutants externally to the atmosphere. These intermediate compounds are recycled internally within a closed loop. While previous studies have identified over 200 possible thermochemical cycles, only a few have progressed beyond theoretical calculations to working experimental demonstrations that establish scientific and practical feasibility of the thermochemical processes. The Cu-Cl cycle has a significant advantage over other cycles due to lower temperature requirements - around 530 oC and below. As a result, it can be eventually linked with the Generation IV thermal power stations. Advantages of the Cu-Cl cycle over others include lower operating temperatures, ability to utilize low-grade waste heat to improve energy efficiency, and potentially lower cost materials. Another significant advantage is a relatively low voltage required for the electrochemical step (thus low electricity input). Other advantages include common chemical agents and reactions going to completion without side reactions, and lower demands on materials of construction. Three university research groups from PSU, USC, and TU as well as a group from ANL have been collaborating on the development of enabling technologies for the Cu-Cl cycle, including experimental work on the Cu-Cl cycle reactions, modeling and simulation, and particularly electrochemical reaction for hydrogen production using a CuCl electrolyzer. The Consortium research was distributed over the participants and organized in the following tasks: (1) Development of CuCl electrolyzer (PSU), (2) Thermodynamic modeling of anolyte solution (PSU), (3) Proton conductive membranes for CuCl electrolysis (PSU), (4) Development of an analytical method for online analysis of copper compounds in highly concentrated aqueous solutions (USC), (5) Electrodialysis as a means for separation and purification of the streams exiting the electrolyzer in the Cu-Cl cycle (USC), (6) Development of nanostructured electrocatalysts for the Cu-Cl electrolysis (USC), (7) Cu-Cl electrolyzer modeling (USC), (8) Aspen Plus modeling of the Cu-Cl thermochemical cycle (TU), (9) International coordination of research on the development of the Cu-Cl thermochemical cycle (ANL). The results obtained in the project clearly demonstrate that the Cu-Cl alternative thermochemical cycle is a promising and viable technology to produce hydrogen efficiently.

  1. Pathways to Commercial Success: Technologies and Products Supported by the Hydrogen, Fuel Cells and Infrastructure Technologies Program

    Fuel Cell Technologies Publication and Product Library (EERE)

    This report documents the results of an effort to identify and characterize commercial and near-commercial (emerging) technologies and products that benefited from the support of the Hydrogen, Fuel Ce

  2. Method for controlling clathrate hydrates in fluid systems

    DOE Patents [OSTI]

    Sloan, E.D. Jr.

    1995-07-11T23:59:59.000Z

    Discussed is a process for preventing clathrate hydrate masses from impeding the flow of fluid in a fluid system. An additive is contacted with clathrate hydrate masses in the system to prevent those clathrate hydrate masses from impeding fluid flow. The process is particularly useful in the natural gas and petroleum production, transportation and processing industry where gas hydrate formation can cause serious problems. Additives preferably contain one or more five member, six member and/or seven member cyclic chemical groupings. Additives include poly(N-vinyl-2-pyrrolidone) and hydroxyethylcellulose, either in combination or alone. Additives can also contain multiple cyclic chemical groupings having different size rings. One such additive is sold under the name Gaffix VC-713.

  3. Method for controlling clathrate hydrates in fluid systems

    DOE Patents [OSTI]

    Sloan, Jr., Earle D. (Golden, CO)

    1995-01-01T23:59:59.000Z

    Discussed is a process for preventing clathrate hydrate masses from impeding the flow of fluid in a fluid system. An additive is contacted with clathrate hydrate masses in the system to prevent those clathrate hydrate masses from impeding fluid flow. The process is particularly useful in the natural gas and petroleum production, transportation and processing industry where gas hydrate formation can cause serious problems. Additives preferably contain one or more five member, six member and/or seven member cyclic chemical groupings. Additives include poly(N-vinyl-2-pyrrolidone) and hydroxyethylcellulose, either in combination or alone. Additives can also contain multiple cyclic chemical groupings having different size rings. One such additive is sold under the name Gaffix VC-713.

  4. CITE Suitability : an exploration of product evaluation methodologies for developing world technologies

    E-Print Network [OSTI]

    Pombrol, Christopher Anthony

    2014-01-01T23:59:59.000Z

    There are a multitude of technological products that have been developed to improve the lives of bottom of pyramid consumers in the developing world. Unfortunately, many of these products fail to have the desired impact ...

  5. Environmental benefits of advanced oil and gas exploration and production technology

    SciTech Connect (OSTI)

    None

    1999-10-01T23:59:59.000Z

    THROUGHOUT THE OIL AND GAS LIFE CYCLE, THE INDUSTRY HAS APPLIED AN ARRAY OF ADVANCED TECHNOLOGIES TO IMPROVE EFFICIENCY, PRODUCTIVITY, AND ENVIRONMENTAL PERFORMANCE. THIS REPORT FOCUSES SPECIFICALLY ON ADVANCES IN EXPLORATION AND PRODUCTION (E&P) OPERATIONS.

  6. Long Tails vs. Superstars: The Effect of Information Technology on Product Variety and Sales Concentration Patterns

    E-Print Network [OSTI]

    Brynjolfsson, Erik

    The Internet and related information technologies are transforming the distribution of product sales across products, and these effects are likely to grow in coming years. Both the Long Tail and the Superstar effect are ...

  7. Trade and plant level productivity gains: Role of Import Liberalisation, Technological Spillovers and Variety Growth in

    E-Print Network [OSTI]

    Bandyopadhyay, Antar

    1 Trade and plant level productivity gains: Role of Import Liberalisation, Technological Spillovers liberalization impact productivity at the micro level in the economy? Using a panel data of Indian manufacturing productivity growth at the production level in the economy. These mechanisms include trade induced pro

  8. The Software Factory: Integrating CASE Technologies to Improve Productivity

    E-Print Network [OSTI]

    Menendez, Jose

    This report addresses the use of computer-aided software engineering (CASE) technology for the development of aircraft software.

  9. Development of a Numerical Simulator for Analyzing the Geomechanical Performance of Hydrate-Bearing Sediments

    SciTech Connect (OSTI)

    Rutqvist, Jonny; Rutqvist, J.; Moridis, G.J.

    2008-06-01T23:59:59.000Z

    In this paper, we describe the development and application of a numerical simulator that analyzes the geomechanical performance of hydrate-bearing sediments, which may become an important future energy supply. The simulator is developed by coupling a robust numerical simulator of coupled fluid flow, hydrate thermodynamics, and phase behavior in geologic media (TOUGH+HYDRATE) with an established geomechanical code (FLAC3D). We demonstrate the current simulator capabilities and applicability for two examples of geomechanical responses of hydrate bearing sediments during production-induced hydrate dissociation. In these applications, the coupled geomechanical behavior within hydrate-bearing seducements are considered through a Mohr-Coulomb constitutive model, corrected for changes in pore-filling hydrate and ice content, based on laboratory data. The results demonstrate how depressurization-based gas production from oceanic hydrate deposits may lead to severe geomechanical problems unless care is taken in designing the production scheme. We conclude that the coupled simulator can be used to design production strategies for optimizing production, while avoiding damaging geomechanical problems.

  10. Hydration and leaching characteristics of cement pastes made from electroplating sludge

    SciTech Connect (OSTI)

    Chen, Ying-Liang [Department of Environmental Engineering, National Cheng Kung University, No. 1, University Rd., Tainan City 70101, Taiwan (China); Sustainable Environment Research Center, National Cheng Kung University, No. 1, University Rd., Tainan City 70101, Taiwan (China); Ko, Ming-Sheng [Institute of Mineral Resources Engineering, National Taipei University of Technology, No. 1, Sec. 3, Chunghsiao E. Rd., Taipei City 10608, Taiwan (China); Lai, Yi-Chieh [Department of Bioenvironmental Engineering, Chung Yuan Christian University, No. 200, Chung-Pei Rd., Chung-Li 32023, Taiwan (China); Chang, Juu-En, E-mail: juuen@mail.ncku.edu.tw [Department of Environmental Engineering, National Cheng Kung University, No. 1, University Rd., Tainan City 70101, Taiwan (China); Sustainable Environment Research Center, National Cheng Kung University, No. 1, University Rd., Tainan City 70101, Taiwan (China)

    2011-06-15T23:59:59.000Z

    The purpose of this study was to investigate the hydration and leaching characteristics of the pastes of belite-rich cements made from electroplating sludge. The compressive strength of the pastes cured for 1, 3, 7, 28, and 90 days was determined, and the condensation of silicate anions in hydrates was examined with the {sup 29}Si nuclear magnetic resonance (NMR) technology. The leachabilities of the electroplating sludge and the hardened pastes were studied with the multiple toxicity characteristic leaching procedure (MTCLP) and the tank leaching test (NEN 7345), respectively. The results showed that the electroplating sludge continued to leach heavy metals, including nickel, copper, and zinc, and posed a serious threat to the environment. The belite-rich cement made from the electroplating sludge was abundant in hydraulic {beta}-dicalcium silicate, and it performed well with regard to compressive-strength development when properly blended with ordinary Portland cements. The blended cement containing up to 40% the belite-rich cement can still satisfy the compressive-strength requirements of ASTM standards, and the pastes cured for 90 days had comparable compressive strength to an ordinary Portland cement paste. It was also found that the later hydration reaction of the blended cements was relatively more active, and high fractions of belite-rich cement increased the chain length of silicate hydrates. In addition, by converting the sludge into belite-rich cements, the heavy metals became stable in the hardened cement pastes. This study thus indicates a viable alternative approach to dealing with heavy metal bearing wastes, and the resulting products show good compressive strength and heavy-metal stability.

  11. SUESS ET AL.: SEA FLOOR METHANE HYDRATES AT HYDRATE RIDGE, CASCADIA MARGIN Sea Floor Methane Hydrates at Hydrate Ridge, Cascadia Margin

    E-Print Network [OSTI]

    Goldfinger, Chris

    a variety of gas hydrates in near-surface sediments. Hydrate formation and destruction continuously shape established that the uppermost sediment column contains several distinct layers of gas hydrate which the seafloor to the atmosphere. 1. INTRODUCTION The biogeochemical processes associated with gas hydrate

  12. Dynamics of Protein Hydration Water

    E-Print Network [OSTI]

    M. Wolf; S. Emmert; R. Gulich; P. Lunkenheimer; A. Loidl

    2014-12-08T23:59:59.000Z

    We present the frequency- and temperature-dependent dielectric properties of lysozyme solutions in a broad concentration regime, measured at subzero temperatures and compare the results with measurements above the freezing point of water and on hydrated lysozyme powder. Our experiments allow examining the dynamics of unfreezable hydration water in a broad temperature range including the so-called No Man's Land (160 - 235 K). The obtained results prove the bimodality of the hydration shell dynamics and are discussed in the context of the highly-debated fragile-to-strong transition of water.

  13. Coupling the Alkaline-Surfactant-Polymer Technology and The Gelation Technology to Maximize Oil Production

    SciTech Connect (OSTI)

    Malcolm Pitts; Jie Qi; Dan Wilson; Phil Dowling; David Stewart; Bill Jones

    2005-12-01T23:59:59.000Z

    Performance and produced polymer evaluation of four alkaline-surfactant-polymer projects concluded that only one of the projects could have benefited from combining the alkaline-surfactant-polymer and gelation technologies. Cambridge, the 1993 Daqing, Mellott Ranch, and the Wardlaw alkaline-surfacant-polymer floods were studied. An initial gel treatment followed by an alkaline-surfactant-polymer flood in the Wardlaw field would have been a benefit due to reduction of fracture flow. Numerical simulation demonstrated that reducing the permeability of a high permeability zone of a reservoir with gel improved both waterflood and alkaline-surfactant-polymer flood oil recovery. A Minnelusa reservoir with both A and B sand production was simulated. A and B sands are separated by a shale layer. A sand and B sand waterflood oil recovery was improved by 196,000 bbls or 3.3% OOIP when a gel was placed in the B sand. Alkaline-surfactant-polymer flood oil recovery improvement over a waterflood was 392,000 bbls or 6.5% OOIP. Placing a gel into the B sand prior to an alkaline-surfactant-polymer flood resulted in 989,000 bbl or 16.4% OOIP more oil than only water injection. A sand and B sand alkaline-surfactant-polymer flood oil recovery was improved by 596,000 bbls or 9.9% OOIP when a gel was placed in the B sand.

  14. A Realistic Technology and Engineering Assessment of Algae Biofuel Production

    E-Print Network [OSTI]

    Quinn, Nigel

    Creek, California Energy Biosciences Institute University of California Berkeley of microalgae biofuels production through an analysis of five production scenarios. These scenarios, or cases, including raceway ponds for microalgae cultivation, bioflocculation for algae harvesting, and hexane

  15. Reactive Dehydration technology for Production of Fuels and Chemicals...

    Broader source: Energy.gov (indexed) [DOE]

    platform (Intensified Catalytic and Reactive Distillation) for compact, inexpensive production of biomass-based chemicals from complex aqueous mixtures. Separation...

  16. Coupling the Alkaline-Surfactant-Polymer Technology and The Gelation Technology to Maximize Oil Production

    SciTech Connect (OSTI)

    Malcolm Pitts; Jie Qi; Dan Wilson; David Stewart; Bill Jones

    2005-10-01T23:59:59.000Z

    Gelation technologies have been developed to provide more efficient vertical sweep efficiencies for flooding naturally fractured oil reservoirs or more efficient areal sweep efficiency for those with high permeability contrast ''thief zones''. The field proven alkaline-surfactant-polymer technology economically recovers 15% to 25% OOIP more oil than waterflooding from swept pore space of an oil reservoir. However, alkaline-surfactant-polymer technology is not amenable to naturally fractured reservoirs or those with thief zones because much of injected solution bypasses target pore space containing oil. This work investigates whether combining these two technologies could broaden applicability of alkaline-surfactant-polymer flooding into these reservoirs. A prior fluid-fluid report discussed interaction of different gel chemical compositions and alkaline-surfactant-polymer solutions. Gel solutions under dynamic conditions of linear corefloods showed similar stability to alkaline-surfactant-polymer solutions as in the fluid-fluid analyses. Aluminum-polyacrylamide, flowing gels are not stable to alkaline-surfactant-polymer solutions of either pH 10.5 or 12.9. Chromium acetate-polyacrylamide flowing and rigid flowing gels are stable to subsequent alkaline-surfactant-polymer solution injection. Rigid flowing chromium acetate-polyacrylamide gels maintained permeability reduction better than flowing chromium acetate-polyacrylamide gels. Silicate-polyacrylamide gels are not stable with subsequent injection of either a pH 10.5 or a 12.9 alkaline-surfactant-polymer solution. Chromium acetate-xanthan gum rigid gels are not stable to subsequent alkaline-surfactant-polymer solution injection. Resorcinol-formaldehyde gels were stable to subsequent alkaline-surfactant-polymer solution injection. When evaluated in a dual core configuration, injected fluid flows into the core with the greatest effective permeability to the injected fluid. The same gel stability trends to subsequent alkaline-surfactant-polymer injected solution were observed. Aluminum citrate-polyacrylamide, resorcinol-formaldehyde, and the silicate-polyacrylamide gel systems did not produce significant incremental oil in linear corefloods. Both flowing and rigid flowing chromium acetate-polyacrylamide gels and the xanthan gum-chromium acetate gel system produced incremental oil with the rigid flowing gel producing the greatest amount. Higher oil recovery could have been due to higher differential pressures across cores. None of the gels tested appeared to alter alkaline-surfactant-polymer solution oil recovery. Total waterflood plus chemical flood oil recovery sequence recoveries were all similar. Chromium acetate-polyacrylamide gel used to seal fractured core maintain fracture closure if followed by an alkaline-surfactant-polymer solution. Chromium acetate gels that were stable to injection of alkaline-surfactant-polymer solutions at 72 F were stable to injection of alkaline-surfactant-polymer solutions at 125 F and 175 F in linear corefloods. Chromium acetate-polyacrylamide gels maintained diversion capability after injection of an alkaline-surfactant-polymer solution in stacked; radial coreflood with a common well bore. Xanthan gum-chromium acetate gels maintained gel integrity in linear corefloods after injection of an alkaline-surfactant-polymer solution at 125 F. At 175 F, Xanthan gum-chromium acetate gels were not stable either with or without subsequent alkaline-surfactant-polymer solution injection. Numerical simulation demonstrated that reducing the permeability of a high permeability zone of a reservoir with gel improved both waterflood and alkaline-surfactant-polymer flood oil recovery. A Minnelusa reservoir with both A and B sand production was simulated. A and B sands are separated by a shale layer. A sand and B sand waterflood oil recovery was improved by 196,000 bbls when a gel was placed in the B sand. A sand and B sand alkaline-surfactant-polymer flood oil recovery was improved by 596,000 bbls when a gel was placed in the B sand. Alkaline-surfactant-pol

  17. Response of oceanic hydrate-bearing sediments to thermal stresses

    E-Print Network [OSTI]

    Moridis, G.J.; Kowalsky, M.B.

    2006-01-01T23:59:59.000Z

    c) aqueous, gas and hydrate phase saturations, (d) waterIntrinsic Rate of Methane Gas Hydrate Decomposition”, Chem.Western Nankai Trough”, in Gas Hydrates: Challenges for the

  18. Examination of Hydrate Formation Methods: Trying to Create Representative Samples

    E-Print Network [OSTI]

    Kneafsey, T.J.

    2012-01-01T23:59:59.000Z

    permeability measurements of gas hydrate-bearing sediments,International Conference on Gas Hydrates, edited, p. 1058,2009), Influence of gas hydrate morphology on the seismic

  19. Studies of Reaction Kinetics of Methane Hydrate Dissocation in Porous Media

    SciTech Connect (OSTI)

    Moridis, George J.; Seol, Yongkoo; Kneafsey, Timothy J.

    2005-03-10T23:59:59.000Z

    The objective of this study is the description of the kinetic dissociation of CH4-hydrates in porous media, and the determination of the corresponding kinetic parameters. Knowledge of the kinetic dissociation behavior of hydrates can play a critical role in the evaluation of gas production potential of gas hydrate accumulations in geologic media. We analyzed data from a sequence of tests of CH4-hydrate dissociation by means of thermal stimulation. These tests had been conducted on sand cores partially saturated with water, hydrate and CH4 gas, and contained in an x-ray-transparent aluminum pressure vessel. The pressure, volume of released gas, and temperature (at several locations within the cores) were measured. To avoid misinterpreting local changes as global processes, x-ray computed tomography scans provided accurate images of the location and movement of the reaction interface during the course of the experiments. Analysis of the data by means of inverse modeling (history matching ) provided estimates of the thermal properties and of the kinetic parameters of the hydration reaction in porous media. Comparison of the results from the hydrate-bearing porous media cores to those from pure CH4-hydrate samples provided a measure of the effect of the porous medium on the kinetic reaction. A tentative model of composite thermal conductivity of hydrate-bearing media was also developed.

  20. Akamai technologies : an analysis of product and platform growth strategies

    E-Print Network [OSTI]

    Piper, Victor L. (Victor Lawrence)

    2013-01-01T23:59:59.000Z

    Akamai Technologies has achieved market leadership in content delivery and application acceleration services and is pursuing aggressive growth. Akamai has advised the market that growth to $5B by 2020 is achievable by ...

  1. Biofuels Fuels Technology Pathway Options for Advanced Drop-in Biofuels Production

    SciTech Connect (OSTI)

    Kevin L Kenney

    2011-09-01T23:59:59.000Z

    Advanced drop-in hydrocarbon biofuels require biofuel alternatives for refinery products other than gasoline. Candidate biofuels must have performance characteristics equivalent to conventional petroleum-based fuels. The technology pathways for biofuel alternatives also must be plausible, sustainable (e.g., positive energy balance, environmentally benign, etc.), and demonstrate a reasonable pathway to economic viability and end-user affordability. Viable biofuels technology pathways must address feedstock production and environmental issues through to the fuel or chemical end products. Potential end products include compatible replacement fuel products (e.g., gasoline, diesel, and JP8 and JP5 jet fuel) and other petroleum products or chemicals typically produced from a barrel of crude. Considering the complexity and technology diversity of a complete biofuels supply chain, no single entity or technology provider is capable of addressing in depth all aspects of any given pathway; however, all the necessary expert entities exist. As such, we propose the assembly of a team capable of conducting an in-depth technology pathway options analysis (including sustainability indicators and complete LCA) to identify and define the domestic biofuel pathways for a Green Fleet. This team is not only capable of conducting in-depth analyses on technology pathways, but collectively they are able to trouble shoot and/or engineer solutions that would give industrial technology providers the highest potential for success. Such a team would provide the greatest possible down-side protection for high-risk advanced drop-in biofuels procurement(s).

  2. Response of oceanic hydrate-bearing sediments to thermalstresses

    SciTech Connect (OSTI)

    Moridis, G.J.; Kowalsky, M.B.

    2006-05-01T23:59:59.000Z

    In this study, we evaluate the response of oceanicsubsurface systems to thermal stresses caused by the flow of warm fluidsthrough noninsulated well systems crossing hydrate-bearing sediments.Heat transport from warm fluids, originating from deeper reservoirs underproduction, into the geologic media can cause dissociation of the gashydrates. The objective of this study is to determine whether gasevolution from hydrate dissociation can lead to excessive pressurebuildup, and possibly to fracturing of hydrate-bearing formations andtheir confining layers, with potentially adverse consequences on thestability of the suboceanic subsurface. This study also aims to determinewhether the loss of the hydrate--known to have a strong cementing effecton the porous media--in the vicinity of the well, coupled with thesignificant pressure increases, can undermine the structural stability ofthe well assembly.Scoping 1D simulations indicated that the formationintrinsic permeability, the pore compressibility, the temperature of theproduced fluids andthe initial hydrate saturation are the most importantfactors affecting the system response, while the thermal conductivity andporosity (above a certain level) appear to have a secondary effect.Large-scale simulations of realistic systems were also conducted,involving complex well designs and multilayered geologic media withnonuniform distribution of properties and initial hydrate saturationsthat are typical of those expected in natural oceanic systems. Theresults of the 2D study indicate that although the dissociation radiusremains rather limited even after long-term production, low intrinsicpermeability and/or high hydrate saturation can lead to the evolution ofhigh pressures that can threaten the formation and its boundaries withfracturing. Although lower maximum pressures are observed in the absenceof bottom confining layers and in deeper (and thus warmer and morepressurized) systems, the reduction is limited. Wellbore designs withgravel packs that allow gas venting and pressure relief result insubstantially lower pressures.

  3. Improved evidence for the existence of an intermediate phase during hydration of tricalcium silicate

    SciTech Connect (OSTI)

    Bellmann, Frank, E-mail: frank.bellmann@uni-weimar.d [Institute for Building Materials Science, Bauhaus University Weimar, 99423 Weimar (Germany); Damidot, Denis [Ecole des Mines de Douai, Civil and Environmental Engineering Department, 941 rue Charles Bourseul, BP 10838, 59508 Doua cedexi (France); Moeser, Bernd [Institute for Building Materials Science, Bauhaus University Weimar, 99423 Weimar (Germany); Skibsted, Jorgen [Instrument Center for Solid-State NMR Spectroscopy and Interdisciplinary Nanoscience Center (iNANO), Department of Chemistry, Aarhus University DK-8000 Aarhus C (Denmark)

    2010-06-15T23:59:59.000Z

    Tricalcium silicate (Ca{sub 3}SiO{sub 5}) with a very small particle size of approximately 50 nm has been prepared and hydrated for a very short time (5 min) by two different modes in a paste experiment, using a water/solid-ratio of 1.20, and by hydration as a suspension employing a water/solid-ratio of 4000. A phase containing uncondensed silicate monomers close to hydrogen atoms (either hydroxyl groups or water molecules) was formed in both experiments. This phase is distinct from anhydrous tricalcium silicate and from the calcium-silicate-hydrate (C-S-H) phase, commonly identified as the hydration product of tricalcium silicate. In the paste experiment, approximately 79% of silicon atoms were present in the hydrated phase containing silicate monomers as determined from {sup 29}Sileft brace{sup 1}Hright brace CP/MAS NMR. This result is used to show that the hydrated silicate monomers are part of a separate phase and that they cannot be attributed to a hydroxylated surface of tricalcium silicate after contact with water. The phase containing hydrated silicate monomers is metastable with respect to the C-S-H phase since it transforms into the latter in a half saturated calcium hydroxide solution. These data is used to emphasize that the hydration of tricalcium silicate proceeds in two consecutive steps. In the first reaction, an intermediate phase containing hydrated silicate monomers is formed which is subsequently transformed into C-S-H as the final hydration product in the second step. The introduction of an intermediate phase in calculations of the early hydration of tricalcium silicate can explain the presence of the induction period. It is shown that heterogeneous nucleation on appropriate crystal surfaces is able to reduce the length of the induction period and thus to accelerate the reaction of tricalcium silicate with water.

  4. New Natural Gas Storage and Transportation Capabilities Utilizing Rapid Methane Hydrate Formation Techniques

    SciTech Connect (OSTI)

    Brown, T.D.; Taylor, C.E.; Bernardo, M.

    2010-01-01T23:59:59.000Z

    Natural gas (methane as the major component) is a vital fossil fuel for the United States and around the world. One of the problems with some of this natural gas is that it is in remote areas where there is little or no local use for the gas. Nearly 50 percent worldwide natural gas reserves of ~6,254.4 trillion ft3 (tcf) is considered as stranded gas, with 36 percent or ~86 tcf of the U.S natural gas reserves totaling ~239 tcf, as stranded gas [1] [2]. The worldwide total does not include the new estimates by U.S. Geological Survey of 1,669 tcf of natural gas north of the Arctic Circle, [3] and the U.S. ~200,000 tcf of natural gas or methane hydrates, most of which are stranded gas reserves. Domestically and globally there is a need for newer and more economic storage, transportation and processing capabilities to deliver the natural gas to markets. In order to bring this resource to market, one of several expensive methods must be used: 1. Construction and operation of a natural gas pipeline 2. Construction of a storage and compression facility to compress the natural gas (CNG) at 3,000 to 3,600 psi, increasing its energy density to a point where it is more economical to ship, or 3. Construction of a cryogenic liquefaction facility to produce LNG, (requiring cryogenic temperatures at <-161 °C) and construction of a cryogenic receiving port. Each of these options for the transport requires large capital investment along with elaborate safety systems. The Department of Energy's Office of Research and Development Laboratories at the National Energy Technology Laboratory (NETL) is investigating new and novel approaches for rapid and continuous formation and production of synthetic NGHs. These synthetic hydrates can store up to 164 times their volume in gas while being maintained at 1 atmosphere and between -10 to -20°C for several weeks. Owing to these properties, new process for the economic storage and transportation of these synthetic hydrates could be envisioned for stranded gas reserves. The recent experiments and their results from the testing within NETL's 15-Liter Hydrate Cell Facility exhibit promising results. Introduction of water at the desired temperature and pressure through an NETL designed nozzle into a temperature controlled methane environment within the 15-Liter Hydrate Cell allowed for instantaneous formation of methane hydrates. The instantaneous and continuous hydrate formation process was repeated over several days while varying the flow rate of water, its' temperature, and the overall temperature of the methane environment. These results clearly indicated that hydrates formed immediately after the methane and water left the nozzle at temperatures above the freezing point of water throughout the range of operating conditions. [1] Oil and Gas Journal Vol. 160.48, Dec 22, 2008. [2] http://www.eia.doe.gov/oiaf/servicerpt/natgas/chapter3.html and http://www.eia.doe.gov/oiaf/servicerpt/natgas/pdf/tbl7.pdf [3] U.S. Geological Survey, “Circum-Arctic Resource Appraisal: Estimates of Undiscovered Oil and Gas North of the Arctic Circle,” May 2008.

  5. New Technologies that Enhance Environmental Protection, Increase Domestic Production, Result from DOE-Supported Consortium

    Broader source: Energy.gov [DOE]

    New technologies that help small, independent oil and natural gas operators contribute to domestic energy production while improving environmental protection have resulted from U.S. Department of Energy support of the Stripper Well Consortium.

  6. Large-Scale Pyrolysis Oil Production: A Technology Assessment and Economic Analysis

    SciTech Connect (OSTI)

    Ringer, M.; Putsche, V.; Scahill, J.

    2006-11-01T23:59:59.000Z

    A broad perspective of pyrolysis technology as it relates to converting biomass substrates to a liquid bio-oil product and a detailed technical and economic assessment of a fast pyrolysis plant.

  7. Alternative and Renewable fuels and Vehicle Technology Program Subject Area: Biofuels production Facilities

    E-Print Network [OSTI]

    Alternative and Renewable fuels and Vehicle Technology Program Subject Area: Biofuels production: Commercial Facilities · Applicant's Legal Name: Yokayo Biofuels, Inc. · Name of project: A Catalyst for Success · Project Description: Yokayo Biofuels, an industry veteran with over 10 years experience

  8. Thermal dissociation behavior and dissociation enthalpies of methane-carbon dioxide mixed hydrates

    SciTech Connect (OSTI)

    Kwon, T.H.; Kneafsey, T.J.; Rees, E.V.L.

    2011-02-15T23:59:59.000Z

    Replacement of methane with carbon dioxide in hydrate has been proposed as a strategy for geologic sequestration of carbon dioxide (CO{sub 2}) and/or production of methane (CH{sub 4}) from natural hydrate deposits. This replacement strategy requires a better understanding of the thermodynamic characteristics of binary mixtures of CH{sub 4} and CO{sub 2} hydrate (CH{sub 4}-CO{sub 2} mixed hydrates), as well as thermophysical property changes during gas exchange. This study explores the thermal dissociation behavior and dissociation enthalpies of CH{sub 4}-CO{sub 2} mixed hydrates. We prepared CH{sub 4}-CO{sub 2} mixed hydrate samples from two different, well-defined gas mixtures. During thermal dissociation of a CH{sub 4}-CO{sub 2} mixed hydrate sample, gas samples from the head space were periodically collected and analyzed using gas chromatography. The changes in CH{sub 4}-CO{sub 2} compositions in both the vapor phase and hydrate phase during dissociation were estimated based on the gas chromatography measurements. It was found that the CO{sub 2} concentration in the vapor phase became richer during dissociation because the initial hydrate composition contained relatively more CO{sub 2} than the vapor phase. The composition change in the vapor phase during hydrate dissociation affected the dissociation pressure and temperature; the richer CO{sub 2} in the vapor phase led to a lower dissociation pressure. Furthermore, the increase in CO{sub 2} concentration in the vapor phase enriched the hydrate in CO{sub 2}. The dissociation enthalpy of the CH{sub 4}-CO{sub 2} mixed hydrate was computed by fitting the Clausius-Clapeyron equation to the pressure-temperature (PT) trace of a dissociation test. It was observed that the dissociation enthalpy of the CH{sub 4}-CO{sub 2} mixed hydrate lays between the limiting values of pure CH{sub 4} hydrate and CO{sub 2} hydrate, increasing with the CO{sub 2} fraction in the hydrate phase.

  9. Transitioning technology from R&D to production

    E-Print Network [OSTI]

    Pulitzer, Seward Webb, 1974-

    2008-01-01T23:59:59.000Z

    Corporate research and development (R&D) drives progress in the high-tech industries. Companies that advance the state-of-the-art in product performance enjoy significant advantages over the competition. However, although ...

  10. Modeling pure methane hydrate dissociation using a numerical simulator from a novel combination of X-ray computed tomography and macroscopic data

    SciTech Connect (OSTI)

    Gupta, A.; Moridis, G.J.; Kneafsey, T.J.; Sloan, Jr., E.D.

    2009-08-15T23:59:59.000Z

    The numerical simulator TOUGH+HYDRATE (T+H) was used to predict the transient pure methane hydrate (no sediment) dissociation data. X-ray computed tomography (CT) was used to visualize the methane hydrate formation and dissociation processes. A methane hydrate sample was formed from granular ice in a cylindrical vessel, and slow depressurization combined with thermal stimulation was applied to dissociate the hydrate sample. CT images showed that the water produced from the hydrate dissociation accumulated at the bottom of the vessel and increased the hydrate dissociation rate there. CT images were obtained during hydrate dissociation to confirm the radial dissociation of the hydrate sample. This radial dissociation process has implications for dissociation of hydrates in pipelines, suggesting lower dissociation times than for longitudinal dissociation. These observations were also confirmed by the numerical simulator predictions, which were in good agreement with the measured thermal data during hydrate dissociation. System pressure and sample temperature measured at the sample center followed the CH{sub 4} hydrate L{sub w}+H+V equilibrium line during hydrate dissociation. The predicted cumulative methane gas production was within 5% of the measured data. Thus, this study validated our simulation approach and assumptions, which include stationary pure methane hydrate-skeleton, equilibrium hydrate-dissociation and heat- and mass-transfer in predicting hydrate dissociation in the absence of sediments. It should be noted that the application of T+H for the pure methane hydrate system (no sediment) is outside the general applicability limits of T+H.

  11. Solder technology in the manufacturing of electronic products

    SciTech Connect (OSTI)

    Vianco, P.T.

    1993-08-01T23:59:59.000Z

    The electronics industry has relied heavily upon the use of soldering for both package construction and circuit assembly. The solder attachment of devices onto printed circuit boards and ceramic microcircuits has supported the high volume manufacturing processes responsible for low cost, high quality consumer products and military hardware. Defects incurred during the manufacturing process are minimized by the proper selection of solder alloys, substrate materials and process parameters. Prototyping efforts are then used to evaluate the manufacturability of the chosen material systems. Once manufacturing feasibility has been established, service reliability of the final product is evaluated through accelerated testing procedures.

  12. Laboratory measurements on core-scale sediment/hydrate samples topredice reservoir behavior

    SciTech Connect (OSTI)

    Kneafsey, Timothy J.; Seol, Yongkoo; Moridis, George J.; Tomutsa,Liviu; Freifeld, Barry M.

    2005-11-02T23:59:59.000Z

    Measurements on hydrate-bearing laboratory and field samplesare necessary in order to provide realistic bounds on parameters used innumerically modeling the production of natural gas from hydrate-bearingreservoirs. The needed parameters include thermal conductivity,permeability, relative permeability-saturation(s) relationships, andcapillary pressure-saturation(s) relationships. We have developed atechnique to make hydrate-bearing samples ranging in scale from coreplug-size to core-size in the laboratory to facilitate making thesemeasurements. In addition to pressure and temperature measurements, weuse x-ray computed tomography scanning to provide high-resolution dataproviding insights on processes occurring in our samples. Several methodsare available to make gas hydrates in the laboratory, and we expect thatthe method used to make the hydrate will impact the behavior of thehydrate sample, and the parameters measured.

  13. High-surface-area hydrated lime for SO2 control

    SciTech Connect (OSTI)

    Rostam-Abadi, M.; Moran, D.L. (Illinois State Geological Survey, Champaign, IL (United States). Minerals Engineering Section)

    1993-03-01T23:59:59.000Z

    Since 1986, the Illinois State Geological Survey (ISGS), has been developing a process to produce high-surface-area hydrated lime (HSAHL) with more activity for adsorbing SO2 than commercially available hydrated lime. HSAHL prepared by the ISGS method as considerably higher surface area and porosity, and smaller mean particle diameter and crystallite size than commercial hydrated lime. The process has been optimized in a batch, bench-scale reactor and has been scaled-up to a 20--100 lb/hr process optimization unit (POU). Experiments have been conducted to optimize the ISGS hydration process and identify key parameters influencing hydrate properties for SO2 capture (surface area, porosity, particle size, and crystallite size). The known how is available to tailor properties of hydrated limes for specific SO2 removal applications. Pilot-scale tests conducted with the HSAHL under conditions typical of burning high-sulfur coals have achieved up to 90% SO2 capture in various DSI systems. The removal results are enough to bring most high-sulfur coals into compliance with acid rain legislation goals for the year 2000. The focus of the POU program is to generate critical engineering data necessary for the private sector to scale-up the process to a commercial level and provide estimates of the optimal cost of construction and operation of a commercial plant. ISGS is currently participating in a clean coal technology program (CCT-1) by providing 50 tons of HSAHL for a demonstration test at Illinois Power's Hennepin station in January 1993.

  14. HYDRATE RESEARCH ACTIVITIES THAT BOTH SUPPORT AND DERIVE FROM THE MONITORING STATION/SEA-FLOOR OBSERVATORY, MISSISSIPPI CANYON 118, NORTHERN GULF OF MEXICO

    SciTech Connect (OSTI)

    Lutken, Carol

    2013-07-31T23:59:59.000Z

    A permanent observatory has been installed on the seafloor at Federal Lease Block, Mississippi Canyon 118 (MC118), northern Gulf of Mexico. Researched and designed by the Gulf of Mexico Hydrates Research Consortium (GOM-HRC) with the geological, geophysical, geochemical and biological characterization of in situ gas hydrates systems as the research goal, the site has been designated by the Bureau of Ocean Energy Management as a permanent Research Reserve where studies of hydrates and related ocean systems may take place continuously and cooperatively into the foreseeable future. The predominant seafloor feature at MC118 is a carbonate-hydrate complex, officially named Woolsey Mound for the founder of both the GOM-HRC and the concept of the permanent seafloor hydrates research facility, the late James Robert “Bob” Woolsey. As primary investigator of the overall project until his death in mid-2008, Woolsey provided key scientific input and served as chief administrator for the Monitoring Station/ Seafloor Observatory (MS-SFO). This final technical report presents highlights of research and accomplishments to date. Although not all projects reached the status originally envisioned, they are all either complete or positioned for completion at the earliest opportunity. All Department of Energy funds have been exhausted in this effort but, in addition, leveraged to great advantage with additional federal input to the project and matched efforts and resources. This report contains final reports on all subcontracts issued by the University of Mississippi, Administrators of the project, Hydrate research activities that both support and derive from the monitoring station/sea-floor Observatory, Mississippi Canyon 118, northern Gulf of Mexico, as well as status reports on the major components of the project. All subcontractors have fulfilled their primary obligations. Without continued funds designated for further project development, the Monitoring Station/Seafloor Observatory is in danger of lapsing into disuse. However, for the present, interest in the site on the continental slope is healthy and The Center for Marine Resources and Environmental Technology continues to coordinate all activity at the MS/SFO as arranged through the BOEM in 2005. Field and laboratory research projects and findings are reviewed, new technologies and tests described. Many new sensors, systems and two custom ROVs have been developed specifically for this project. Characteristics of marine gas hydrates are dramatically more refined than when the project was initiated and include appear in sections entitled Accomplishments, Products and Publications.

  15. Solubility of Hematite Revisited: Effects of Hydration

    E-Print Network [OSTI]

    Burgos, William

    immediately after synthesis, but [Fe(III)diss] increased with hydration time to be consistent with the predicted solubility of goethite or hydrous ferric oxide (HFO), hydrated analogues of hematite. X an equilibrium with goethite or HFO. This is the first experimental confirmation that the interfacial hydration

  16. 2010 Pathways to Commercial Success: Technologies and Products Supported by

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the YouTube platform is always evolving, soFuel Cell Technologies Market10 New Fuel Cellthe

  17. DOE Fuel Cell Technologies Office Record 12024: Hydrogen Production Cost

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't Your Destiny: Theof"Wave theJulyD&D Project|StatementDOE Fuel Cell Technologies

  18. Occurrence of gas hydrate in Oligocene Frio sand: Alaminos Canyon Block 818: Northern Gulf of Mexico

    SciTech Connect (OSTI)

    Boswell, R.D.; Shelander, D.; Lee, M.; Latham, T.; Collett, T.; Guerin, G.; Moridis, G.; Reagan, M.; Goldberg, D.

    2009-07-15T23:59:59.000Z

    A unique set of high-quality downhole shallow subsurface well log data combined with industry standard 3D seismic data from the Alaminos Canyon area has enabled the first detailed description of a concentrated gas hydrate accumulation within sand in the Gulf of Mexico. The gas hydrate occurs within very fine grained, immature volcaniclastic sands of the Oligocene Frio sand. Analysis of well data acquired from the Alaminos Canyon Block 818 No.1 ('Tigershark') well shows a total gas hydrate occurrence 13 m thick, with inferred gas hydrate saturation as high as 80% of sediment pore space. Average porosity in the reservoir is estimated from log data at approximately 42%. Permeability in the absence of gas hydrates, as revealed from the analysis of core samples retrieved from the well, ranges from 600 to 1500 millidarcies. The 3-D seismic data reveals a strong reflector consistent with significant increase in acoustic velocities that correlates with the top of the gas-hydrate-bearing sand. This reflector extends across an area of approximately 0.8 km{sup 2} and delineates the minimal probable extent of the gas hydrate accumulation. The base of the inferred gas-hydrate zone also correlates well with a very strong seismic reflector that indicates transition into units of significantly reduced acoustic velocity. Seismic inversion analyses indicate uniformly high gas-hydrate saturations throughout the region where the Frio sand exists within the gas hydrate stability zone. Numerical modeling of the potential production of natural gas from the interpreted accumulation indicates serious challenges for depressurization-based production in settings with strong potential pressure support from extensive underlying aquifers.

  19. Comparison of kinetic and equilibrium reaction models insimulating gas hydrate behavior in porous media

    SciTech Connect (OSTI)

    Kowalsky, Michael B.; Moridis, George J.

    2006-11-29T23:59:59.000Z

    In this study we compare the use of kinetic and equilibriumreaction models in the simulation of gas (methane) hydrate behavior inporous media. Our objective is to evaluate through numerical simulationthe importance of employing kinetic versus equilibrium reaction modelsfor predicting the response of hydrate-bearing systems to externalstimuli, such as changes in pressure and temperature. Specifically, we(1) analyze and compare the responses simulated using both reactionmodels for natural gas production from hydrates in various settings andfor the case of depressurization in a hydrate-bearing core duringextraction; and (2) examine the sensitivity to factors such as initialhydrate saturation, hydrate reaction surface area, and numericaldiscretization. We find that for large-scale systems undergoing thermalstimulation and depressurization, the calculated responses for bothreaction models are remarkably similar, though some differences areobserved at early times. However, for modeling short-term processes, suchas the rapid recovery of a hydrate-bearing core, kinetic limitations canbe important, and neglecting them may lead to significantunder-prediction of recoverable hydrate. The use of the equilibriumreaction model often appears to be justified and preferred for simulatingthe behavior of gas hydrates, given that the computational demands forthe kinetic reaction model far exceed those for the equilibrium reactionmodel.

  20. Development of Alaskan gas hydrate resources: Annual report, October 1986--September 1987

    SciTech Connect (OSTI)

    Sharma, G.D.; Kamath, V.A.; Godbole, S.P.; Patil, S.L.; Paranjpe, S.G.; Mutalik, P.N.; Nadem, N.

    1987-10-01T23:59:59.000Z

    Solid ice-like mixtures of natural gas and water in the form of natural gas hydrated have been found immobilized in the rocks beneath the permafrost in Arctic basins and in muds under the deep water along the American continental margins, in the North Sea and several other locations around the world. It is estimated that the arctic areas of the United States may contain as much as 500 trillion SCF of natural gas in the form of gas hydrates (Lewin and Associates, 1983). While the US Arctic gas hydrate resources may have enormous potential and represent long term future source of natural gas, the recovery of this resource from reservoir frozen with gas hydrates has not been commercialized yet. Continuing study and research is essential to develop technologies which will enable a detailed characterization and assessment of this alternative natural gas resource, so that development of cost effective extraction technology.

  1. High-pressure gas hydrates 

    E-Print Network [OSTI]

    Loveday, J. S.; Nelmes, R. J.

    It has long been known that crystalline hydrates are formed by many simple gases that do not interact strongly with water, and in most cases the gas molecules or atoms occupy 'cages' formed by a framework of water molecules. The majority...

  2. Battery Company Puts New Nanowire Technology into Production | Department

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office511041cloth DocumentationProductsAlternativeOperationalAugustDecade5-F,INITIALoperatorBassi IBMof

  3. Conversion Technologies for Advanced Biofuels … Carbohydrates Production

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels Data Center Home Page onYouTube YouTube Note: Since the YouTube platformBuildingCoalComplex(GC-72) |Reserve | DepartmentControls(FactProduction

  4. Clean coal technology. Coal utilisation by-products

    SciTech Connect (OSTI)

    NONE

    2006-08-15T23:59:59.000Z

    The need to remove the bulk of ash contained in flue gas from coal-fired power plants coupled with increasingly strict environmental regulations in the USA result in increased generation of solid materials referred to as coal utilisation by-products, or CUBs. More than 40% of CUBs were sold or reused in the USA in 2004 compared to less than 25% in 1996. A goal of 50% utilization has been established for 2010. The American Coal Ash Association (ACCA) together with the US Department of Energy's Power Plant Improvement Initiative (PPPI) and Clean Coal Power Initiative (CCPI) sponsor a number of projects that promote CUB utilization. Several are mentioned in this report. Report sections are: Executive summary; Introduction; Where do CUBs come from?; Market analysis; DOE-sponsored CUB demonstrations; Examples of best-practice utilization of CUB materials; Factors limiting the use of CUBs; and Conclusions. 14 refs., 1 fig., 5 tabs., 14 photos.

  5. COUPLING THE ALKALINE-SURFACTANT-POLYMER TECHNOLOGY AND THE GELATION TECHNOLOGY TO MAXIMIZE OIL PRODUCTION

    SciTech Connect (OSTI)

    Malcolm Pitts; Jie Qi; Dan Wilson

    2004-10-01T23:59:59.000Z

    Gelation technologies have been developed to provide more efficient vertical sweep efficiencies for flooding naturally fractured oil reservoirs or more efficient areal sweep efficiency for those with high permeability contrast ''thief zones''. The field proven alkaline-surfactant-polymer technology economically recovers 15% to 25% OOIP more oil than waterflooding from swept pore space of an oil reservoir. However, alkaline-surfactant-polymer technology is not amenable to naturally fractured reservoirs or those with thief zones because much of injected solution bypasses target pore space containing oil. This work investigates whether combining these two technologies could broaden applicability of alkaline-surfactant-polymer flooding into these reservoirs. A prior fluid-fluid report discussed interaction of different gel chemical compositions and alkaline-surfactant-polymer solutions. Gel solutions under dynamic conditions of linear corefloods showed similar stability to alkaline-surfactant-polymer solutions as in the fluid-fluid analyses. Aluminum-polyacrylamide, flowing gels are not stable to alkaline-surfactant-polymer solutions of either pH 10.5 or 12.9. Chromium acetate-polyacrylamide flowing and rigid flowing gels are stable to subsequent alkaline-surfactant-polymer solution injection. Rigid flowing chromium acetate-polyacrylamide gels maintained permeability reduction better than flowing chromium acetate-polyacrylamide gels. Silicate-polyacrylamide gels are not stable with subsequent injection of either a pH 10.5 or a 12.9 alkaline-surfactant-polymer solution. Neither aluminum citrate-polyacrylamide nor silicate-polyacrylamide gel systems produced significant incremental oil in linear corefloods. Both flowing and rigid flowing chromium acetate-polyacrylamide gels produced incremental oil with the rigid flowing gel producing the greatest amount. Higher oil recovery could have been due to higher differential pressures across cores. None of the gels tested appeared to alter alkaline-surfactant-polymer solution oil recovery. Total waterflood plus chemical flood oil recovery sequence recoveries were all similar.

  6. COUPLING THE ALKALINE-SURFACTANT-POLYMER TECHNOLOGY AND THE GELATION TECHNOLOGY TO MAXIMIZE OIL PRODUCTION

    SciTech Connect (OSTI)

    Malcolm Pitts; Jie Qui; Dan Wilson; Phil Dowling

    2004-05-01T23:59:59.000Z

    Gelation technologies have been developed to provide more efficient vertical sweep efficiencies for flooding naturally fractured oil reservoirs or more efficient areal sweep efficiency those with high permeability contrast ''thief zones''. The field proven alkaline-surfactant-polymer technology economically recovers 15% to 25% OOIP more oil than waterflooding in the swept pore space of an oil reservoir. However, alkaline-surfactant-polymer technology is not amenable to the naturally fractured reservoirs or those with thief zones because much of the injected solution bypasses the target pore space containing oil. The objective of this work is to investigate whether combining these two technologies could broaden the applicability of alkaline-surfactant-polymer flooding into these reservoirs. Fluid-fluid interaction with different gel chemical compositions and alkaline-surfactant-polymer solution with pH values ranging from 9.2 to 12.9 have been tested. Aluminum-polyacrylamide gels are not stable to alkaline-surfactant-polymer solutions at any pH. Chromium--polyacrylamide gels with polymer to chromium ion ratios of 25 or greater were stable to alkaline-surfactant-polymer solutions if solution pH was 10.6 or less. When the polymer to chromium ion was 15 or less, chromium-polyacrylamide gels were stable to alkaline-surfactant-polymer solutions with pH values up to 12.9. Chromium-xanthan gum gels were stable to alkaline-surfactant-polymer solutions with pH values of 12.9 at the polymer to chromium ion ratios tested. Silicate-polyacrylamide, resorcinol-formaldehyde, and sulfomethylated resorcinol-formaldehyde gels were also stable to alkaline-surfactant-polymer solutions with pH values ranging from 9.2 to 12.9. Iron-polyacrylamide gels were immediately destroyed when contacted with any of the alkaline-surfactant-polymer solutions with pH values of 9.2 to 12.9.

  7. WABASH RIVER INTEGRATED METHANOL AND POWER PRODUCTION FROM CLEAN COAL TECHNOLOGIES (IMPPCCT)

    SciTech Connect (OSTI)

    Albert Tsang

    2003-03-14T23:59:59.000Z

    The Wabash River Integrated Methanol and Power Production from Clean Coal Technologies (IMPPCCT) project is evaluating integrated electrical power generation and methanol production through clean coal technologies. The project is conducted by a multi-industry team lead by Gasification Engineering Corporation (GEC), a company of Global Energy Inc., and supported by Air Products and Chemicals, Inc., Dow Chemical Company, Dow Corning Corporation, Methanex Corporation, and Siemens Westinghouse Power Corporation. Three project phases are planned for execution over several years, including: (1) Feasibility study and conceptual design for an integrated demonstration facility, and for fence-line commercial embodiment plants (CEP) operated at Dow Chemical or Dow Corning chemical plant locations (2) Research, development, and testing to define any technology gaps or critical design and integration issues (3) Engineering design and financing plan to install an integrated commercial demonstration facility at the existing Wabash River Energy Limited (WREL) plant in West Terre Haute, Indiana.

  8. Laboratory measurements on core-scale sediment/hydrate samples to predice reservoir behavior

    E-Print Network [OSTI]

    Kneafsey, Timothy J.; Seol, Yongkoo; Moridis, George J.; Tomutsa, Liviu; Freifeld, Barry M.

    2008-01-01T23:59:59.000Z

    International Conference on Gas Hydrates, Trondheim, Norway,coring of near-surface gas hydrate sediments on HydrateInternational Conference on Gas Hydrates, Trondheim, Norway,

  9. Presentations from the March 27th - 28th Methane Hydrates Advisory...

    Office of Environmental Management (EM)

    from the March 27th - 28th Methane Hydrates Advisory Committee Meeting International Gas Hydrate Research DOE's Natural Gas Hydrates Program Gas Hydrates as a Geohazard: What...

  10. Laboratory measurements on core-scale sediment/hydrate samples to predice reservoir behavior

    E-Print Network [OSTI]

    Kneafsey, Timothy J.; Seol, Yongkoo; Moridis, George J.; Tomutsa, Liviu; Freifeld, Barry M.

    2008-01-01T23:59:59.000Z

    International Conference on Gas Hydrates, Yokohama, May 19-International Conference on Gas Hydrates, Trondheim, Norway,coring of near-surface gas hydrate sediments on Hydrate

  11. Development and production of two explosive components using SCB technology

    SciTech Connect (OSTI)

    Tarbell, W.W.; Sanchez, D.H. [Sandia National Labs., Albuquerque, NM (United States); Oestreich, M.L.; Prentice, J.W. [Pacific Scientific, Inc., Chandler, AZ (United States). Energy Dynamics Div.

    1995-05-01T23:59:59.000Z

    For many years, explosive components have used hotwires to convert an electrical stimulus into the thermal energy required to initiate the device. A Semi-Conductor Bridge (SCB) performs the same function, but with the advantage of requiring approximately 1/10 the input energy of a comparable hotwire, while retaining excellent no-fire characteristics. The SCB also demonstrates faster function times due to its inherently-lower thermal mass. This paper discusses the development and production of two SCB-based devices, the MC4491 Initiator and the MC4492 Actuator. The initiator is designed to shock initiate a linear shaped charge by accelerating a thin metal plate across a small gap. The actuator functions several different components, serving as either an actuator by producing a rapidly expanding gas to activate piston mechanisms or as an ignitor by providing hot particles for initiating pyrotechnic mixtures. Details are provided on the construction of both devices, methods of assembly, and performance characteristics (function time, flyer velocity, pressure in a closed bomb, heat content, and no-fire and all-fire levels).

  12. Multi-property characterization chamber for geophysical-hydrological investigations of hydrate bearing sediments

    SciTech Connect (OSTI)

    Seol, Yongkoo, E-mail: Yongkoo.Seol@netl.doe.gov; Choi, Jeong-Hoon; Dai, Sheng [National Energy Technology Laboratory, U.S. Department of Energy, Morgantown, West Virginia 26507 (United States)

    2014-08-01T23:59:59.000Z

    With the increase in the interest of producing natural gas from methane hydrates as well as potential risks of massive hydrate dissociation in the context of global warming, studies have recently shifted from pure hydrate crystals to hydrates in sediments. Such a research focus shift requires a series of innovative laboratory devices that are capable of investigating various properties of hydrate-bearing sediments (HBS). This study introduces a newly developed high pressure testing chamber, i.e., multi-property characterization chamber (MPCC), that allows simultaneous investigation of a series of fundamental properties of HBS, including small-strain stiffness (i.e., P- and S-waves), shear strength, large-strain deformation, stress-volume responses, and permeability. The peripheral coolant circulation system of the MPCC permits stable and accurate temperature control, while the core holder body, made of aluminum, enables X-ray computer tomography scanning to be easily employed for structural and morphological characterization of specimens. Samples of hydrate-bearing sediments are held within a rubber sleeve inside the chamber. The thick sleeve is more durable and versatile than thin membranes while also being much softer than oedometer-type chambers that are incapable of enabling flow tests. Bias introduced by the rubber sleeve during large deformation tests are also calibrated both theoretically and experimentally. This system provides insight into full characterization of hydrate-bearing sediments in the laboratory, as well as pressure core technology in the field.

  13. Advancing Commercialization of Algal Biofuels Through Increased Biomass Productivity and Technology Integration

    SciTech Connect (OSTI)

    Bai, Xuemei [Cellana LLC; Sabarsky, Martin

    2013-09-30T23:59:59.000Z

    Cellana is a leading developer of algae-based bioproducts, and its pre-commercial production of marine microalgae takes place at Cellana?s Kona Demonstration Facility (KDF) in Hawaii. KDF is housing more than 70 high-performing algal strains for different bioproducts, of which over 30 have been grown outside at scale. So far, Cellana has produced more than 10 metric tons of algal biomass for the development of biofuels, animal feed, and high-value nutraceuticals. Cellana?s ALDUO algal cultivation technology allows Cellana to grow non-extremophile algal strains at large scale with no contamination disruptions. Cellana?s research and production at KDF have addressed three major areas that are crucial for the commercialization of algal biofuels: yield improvement, cost reduction, and the overall economics. Commercially acceptable solutions have been developed and tested for major factors limiting areal productivity of algal biomass and lipids based on years of R&D work conducted at KDF. Improved biomass and lipid productivity were achieved through strain improvement, culture management strategies (e.g., alleviation of self-shading, de-oxygenation, and efficient CO2 delivery), and technical advancement in downstream harvesting technology. Cost reduction was achieved through optimized CO2 delivery system, flue gas utilization technology, and energy-efficient harvesting technology. Improved overall economics was achieved through a holistic approach by integration of high-value co-products in the process, in addition to yield improvements and cost reductions.

  14. COUPLING THE ALKALINE-SURFACTANT-POLYMER TECHNOLOGY AND THE GELATION TECHNOLOGY TO MAXIMIZE OIL PRODUCTION

    SciTech Connect (OSTI)

    Malcolm Pitts; Jie Qi; Dan Wilson; David Stewart; Bill Jones

    2005-04-01T23:59:59.000Z

    Gelation technologies have been developed to provide more efficient vertical sweep efficiencies for flooding naturally fractured oil reservoirs or more efficient areal sweep efficiency for those with high permeability contrast ''thief zones''. The field proven alkaline-surfactant-polymer technology economically recovers 15% to 25% OOIP more oil than waterflooding from swept pore space of an oil reservoir. However, alkaline-surfactant-polymer technology is not amenable to naturally fractured reservoirs or those with thief zones because much of injected solution bypasses target pore space containing oil. This work investigates whether combining these two technologies could broaden applicability of alkaline-surfactant-polymer flooding into these reservoirs. A prior fluid-fluid report discussed interaction of different gel chemical compositions and alkaline-surfactant-polymer solutions. Gel solutions under dynamic conditions of linear corefloods showed similar stability to alkaline-surfactant-polymer solutions as in the fluid-fluid analyses. Aluminum-polyacrylamide, flowing gels are not stable to alkaline-surfactant-polymer solutions of either pH 10.5 or 12.9. Chromium acetate-polyacrylamide flowing and rigid flowing gels are stable to subsequent alkaline-surfactant-polymer solution injection. Rigid flowing chromium acetate-polyacrylamide gels maintained permeability reduction better than flowing chromium acetate-polyacrylamide gels. Silicate-polyacrylamide gels are not stable with subsequent injection of either a pH 10.5 or a 12.9 alkaline-surfactant-polymer solution. Chromium acetate-xanthan gum rigid gels are not stable to subsequent alkaline-surfactant-polymer solution injection. Resorcinol-formaldehyde gels were stable to subsequent alkaline-surfactant-polymer solution injection. When evaluated in a dual core configuration, injected fluid flows into the core with the greatest effective permeability to the injected fluid. The same gel stability trends to subsequent alkaline-surfactant-polymer injected solution were observed. Aluminum citrate-polyacrylamide, resorcinol-formaldehyde, and the silicate-polyacrylamide gel systems did not produce significant incremental oil in linear corefloods. Both flowing and rigid flowing chromium acetate-polyacrylamide gels and the xanthan gum-chromium acetate gel system produced incremental oil with the rigid flowing gel producing the greatest amount. Higher oil recovery could have been due to higher differential pressures across cores. None of the gels tested appeared to alter alkaline-surfactant-polymer solution oil recovery. Total waterflood plus chemical flood oil recovery sequence recoveries were all similar.

  15. RESULTS FROM THE (1) DATA COLLECTION WORKSHOP, (2) MODELING WORKSHOP AND (3) DRILLING AND CORING METHODS WORKSHOP AS PART OF THE JOINT INDUSTRY PARTICIPATION (JIP) PROJECT TO CHARACTERIZE NATURAL GAS HYDRATES IN THE DEEPWATER GULF OF MEXICO

    SciTech Connect (OSTI)

    Stephen A. Holditch; Emrys Jones

    2002-09-01T23:59:59.000Z

    In 2000, Chevron began a project to learn how to characterize the natural gas hydrate deposits in the deepwater portions of the Gulf of Mexico. A Joint Industry Participation (JIP) group was formed in 2001, and a project partially funded by the U.S. Department of Energy (DOE) began in October 2001. The primary objective of this project is to develop technology and data to assist in the characterization of naturally occurring gas hydrates in the deepwater Gulf of Mexico. These naturally occurring gas hydrates can cause problems relating to drilling and production of oil and gas, as well as building and operating pipelines. Other objectives of this project are to better understand how natural gas hydrates can affect seafloor stability, to gather data that can be used to study climate change, and to determine how the results of this project can be used to assess if and how gas hydrates act as a trapping mechanism for shallow oil or gas reservoirs. As part of the project, three workshops were held. The first was a data collection workshop, held in Houston during March 14-15, 2002. The purpose of this workshop was to find out what data exist on gas hydrates and to begin making that data available to the JIP. The second and third workshop, on Geoscience and Reservoir Modeling, and Drilling and Coring Methods, respectively, were held simultaneously in Houston during May 9-10, 2002. The Modeling Workshop was conducted to find out what data the various engineers, scientists and geoscientists want the JIP to collect in both the field and the laboratory. The Drilling and Coring workshop was to begin making plans on how we can collect the data required by the project's principal investigators.

  16. Scientific Objectives of the Gulf of Mexico Gas Hydrate JIP Leg II Drilling

    SciTech Connect (OSTI)

    Jones, E. (Chevron); Latham, T. (Chevron); McConnell, D. (AOA Geophysics); Frye, M. (Minerals Management Service); Hunt, J. (Minerals Management Service); Shedd, W. (Minerals Management Service); Shelander, D. (Schlumberger); Boswell, R.M. (NETL); Rose, K.K. (NETL); Ruppel, C. (USGS); Hutchinson, D. (USGS); Collett, T. (USGS); Dugan, B. (Rice University); Wood, W. (Naval Research Laboratory)

    2008-05-01T23:59:59.000Z

    The Gulf of Mexico Methane Hydrate Joint Industry Project (JIP) has been performing research on marine gas hydrates since 2001 and is sponsored by both the JIP members and the U.S. Department of Energy. In 2005, the JIP drilled the Atwater Valley and Keathley Canyon exploration blocks in the Gulf of Mexico to acquire downhole logs and recover cores in silt- and clay-dominated sediments interpreted to contain gas hydrate based on analysis of existing 3-D seismic data prior to drilling. The new 2007-2009 phase of logging and coring, which is described in this paper, will concentrate on gas hydrate-bearing sands in the Alaminos Canyon, Green Canyon, and Walker Ridge protraction areas. Locations were selected to target higher permeability, coarser-grained lithologies (e.g., sands) that have the potential for hosting high saturations of gas hydrate and to assist the U.S. Minerals Management Service with its assessment of gas hydrate resources in the Gulf of Mexico. This paper discusses the scientific objectives for drilling during the upcoming campaign and presents the results from analyzing existing seismic and well log data as part of the site selection process. Alaminos Canyon 818 has the most complete data set of the selected blocks, with both seismic data and comprehensive downhole log data consistent with the occurrence of gas hydrate-bearing sands. Preliminary analyses suggest that the Frio sandstone just above the base of the gas hydrate stability zone may have up to 80% of the available sediment pore space occupied by gas hydrate. The proposed sites in the Green Canyon and Walker Ridge areas are also interpreted to have gas hydrate-bearing sands near the base of the gas hydrate stability zone, but the choice of specific drill sites is not yet complete. The Green Canyon site coincides with a 4-way closure within a Pleistocene sand unit in an area of strong gas flux just south of the Sigsbee Escarpment. The Walker Ridge site is characterized by a sand-prone sedimentary section that rises stratigraphically across the base of the gas hydrate stability zone and that has seismic indicators of gas hydrate. Copyright 2008, Offshore Technology Conference

  17. Multiple stage multiple filter hydrate store

    DOE Patents [OSTI]

    Bjorkman, H.K. Jr.

    1983-05-31T23:59:59.000Z

    An improved hydrate store for a metal halogen battery system is disclosed which employs a multiple stage, multiple filter means for separating the halogen hydrate from the liquid used in forming the hydrate. The filter means is constructed in the form of three separate sections which combine to substantially cover the interior surface of the store container. Exit conduit means is provided in association with the filter means for transmitting liquid passing through the filter means to a hydrate former subsystem. The hydrate former subsystem combines the halogen gas generated during the charging of the battery system with the liquid to form the hydrate in association with the store. Relief valve means is interposed in the exit conduit means for controlling the operation of the separate sections of the filter means, such that the liquid flow through the exit conduit means from each of the separate sections is controlled in a predetermined sequence. The three separate sections of the filter means operate in three discrete stages to provide a substantially uniform liquid flow to the hydrate former subsystem during the charging of the battery system. The separation of the liquid from the hydrate causes an increase in the density of the hydrate by concentrating the hydrate along the filter means. 7 figs.

  18. Multiple stage multiple filter hydrate store

    DOE Patents [OSTI]

    Bjorkman, Jr., Harry K. (Birmingham, MI)

    1983-05-31T23:59:59.000Z

    An improved hydrate store for a metal halogen battery system is disclosed which employs a multiple stage, multiple filter means or separating the halogen hydrate from the liquid used in forming the hydrate. The filter means is constructed in the form of three separate sections which combine to substantially cover the interior surface of the store container. Exit conduit means is provided in association with the filter means for transmitting liquid passing through the filter means to a hydrate former subsystem. The hydrate former subsystem combines the halogen gas generated during the charging of the battery system with the liquid to form the hydrate in association with the store. Relief valve means is interposed in the exit conduit means for controlling the operation of the separate sections of the filter means, such that the liquid flow through the exit conduit means from each of the separate sections is controlled in a predetermined sequence. The three separate sections of the filter means operate in three discrete stages to provide a substantially uniform liquid flow to the hydrate former subsystem during the charging of the battery system. The separation of the liquid from the hydrate causes an increase in the density of the hydrate by concentrating the hydrate along the filter means.

  19. Gas hydrate cool storage system

    DOE Patents [OSTI]

    Ternes, Mark P. (Knoxville, TN); Kedl, Robert J. (Oak Ridge, TN)

    1985-01-01T23:59:59.000Z

    This invention is a process for formation of a gas hydrate to be used as a cool storage medium using a refrigerant in water. Mixing of the immiscible refrigerant and water is effected by addition of a surfactant and agitation. The difficult problem of subcooling during the process is overcome by using the surfactant and agitation and performance of the process significantly improves and approaches ideal.

  20. Methane Hydrate Production Feasibility | Department of Energy

    Broader source: Energy.gov (indexed) [DOE]

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645 3,625 1,006 492 742Energy China 2015of 2005 atthe District ofInstitute Regarding ProposedOnU.SformentorsTheThe red

  1. Noble gases and radiocarbon in natural gas hydrates Gisela Winckler

    E-Print Network [OSTI]

    Aeschbach-Hertig, Werner

    Noble gases and radiocarbon in natural gas hydrates Gisela Winckler Lamont-Doherty Earth 2001; published 24 May 2002. [1] In samples of pure natural gas hydrates from Hydrate Ridge, Cascadia ones preferentially incorporated into the gas hydrate structure. The hydrate methane is devoid of 14 C

  2. High Temperature Electrolysis for Hydrogen Production from Nuclear Energy – TechnologySummary

    SciTech Connect (OSTI)

    J. E. O'Brien; C. M. Stoots; J. S. Herring; M. G. McKellar; E. A. Harvego; M. S. Sohal; K. G. Condie

    2010-02-01T23:59:59.000Z

    The Department of Energy, Office of Nuclear Energy, has requested that a Hydrogen Technology Down-Selection be performed to identify the hydrogen production technology that has the best potential for timely commercial demonstration and for ultimate deployment with the Next Generation Nuclear Plant (NGNP). An Independent Review Team has been assembled to execute the down-selection. This report has been prepared to provide the members of the Independent Review Team with detailed background information on the High Temperature Electrolysis (HTE) process, hardware, and state of the art. The Idaho National Laboratory has been serving as the lead lab for HTE research and development under the Nuclear Hydrogen Initiative. The INL HTE program has included small-scale experiments, detailed computational modeling, system modeling, and technology demonstration. Aspects of all of these activities are included in this report. In terms of technology demonstration, the INL successfully completed a 1000-hour test of the HTE Integrated Laboratory Scale (ILS) technology demonstration experiment during the fall of 2008. The HTE ILS achieved a hydrogen production rate in excess of 5.7 Nm3/hr, with a power consumption of 18 kW. This hydrogen production rate is far larger than has been demonstrated by any of the thermochemical or hybrid processes to date.

  3. Approaches for Identifying Consumer Preferences for the Design of Technology Products: A Case Study of Residential Solar Panels

    E-Print Network [OSTI]

    Chen, Heidi Q.

    This paper investigates ways to obtain consumer preferences for technology products to help designers identify the key attributes that contribute to a product's market success. A case study of residential photovoltaic ...

  4. Approaches for identifying consumer preferences for the design of technology products : a case study of residential solar panels

    E-Print Network [OSTI]

    Chen, Heidi Qianyi

    2012-01-01T23:59:59.000Z

    This thesis investigates ways to obtain consumer preferences for technology products to help designers identify the key attributes that contribute to a product's market success. A case study of residential solar PV panels ...

  5. Roberta Zobbi Policy officer Nanosciences and Nanotechnologies, materials and new production technologies

    E-Print Network [OSTI]

    De Cindio, Fiorella

    production technologies 5. Energy 6. Environment (including climate change) 7. Transport (including aeronautics) 8. Socio-economic sciences and the humanities 9. Security and space + Euratom: Fusion energy. Hazard reduction in plant & storage Knowl-based, sust. proc., eco-innovation Public awareness, sust

  6. Chemical Emissions of Residential Materials and Products: Review of Available Information Environmental Energy Technologies Division

    E-Print Network [OSTI]

    -up approach of collecting and evaluating emissions data from construction and interior materials and commonChemical Emissions of Residential Materials and Products: Review of Available Information Building Technologies Program, Office of Energy Efficiency and Renewable Energy under DOE Contract No. DE

  7. Hydrogen, Fuel Cells, and Infrastructure Technologies FY 2003 Progress Report Photoelectrochemical Hydrogen Production

    E-Print Network [OSTI]

    Hydrogen, Fuel Cells, and Infrastructure Technologies FY 2003 Progress Report 1 Photoelectrochemical Hydrogen Production Eric L. Miller (Primary Contact), Daniela Paluselli, Bjorn Marsen, Richard HPEs based on best available materials systems. · Demonstrate 7.5% solar-to-hydrogen (STH) efficiency

  8. Submitted to The First World Congress on Integrated Design and Process Technology Integrated Production Systems for

    E-Print Network [OSTI]

    Foss, Bjarne A.

    and petrochemical plants, oil-processing plants including re neries, pulp and paper plants, metallurgical plantsSubmitted to The First World Congress on Integrated Design and Process Technology Integrated Production Systems for The Process Industries yBjarne A. Foss 1, zRoger Klev, zMorten Levin, xKristian Lien y

  9. WABASH RIVER INTEGRATED METHANOL AND POWER PRODUCTION FROM CLEAN COAL TECHNOLOGIES (IMPPCCT)

    SciTech Connect (OSTI)

    Thomas Lynch

    2004-01-07T23:59:59.000Z

    The Wabash River Integrated Methanol and Power Production from Clean Coal Technologies (IMPPCCT) project is evaluating integrated electrical power generation and methanol production through clean coal technologies. The project is conducted by a multi-industry team lead previously by Gasification Engineering Corporation (GEC). The project is now under the leadership of ConocoPhillips Company (COP) after it acquired GEC and the E-Gas{trademark} gasification technology from Global Energy in July 2003. The Phase I of this project was supported by Air Products and Chemicals, Inc., Dow Chemical Company, Dow Corning Corporation, Methanex Corporation, and Siemens Westinghouse Power Corporation, while the Phase II is supported by Gas Technology Institute, TDA Research, Inc., and Nucon International, Inc. The two project phases planned for execution include: (1) Feasibility study and conceptual design for an integrated demonstration facility at Global Energy's existing Wabash River Energy Limited (WREL) plant in West Terre Haute, Indiana, and for a fence-line commercial embodiment plants (CEP) operated at Dow Chemical or Dow Corning chemical plant locations (2) Research, development, and testing (RD&T) to define any technology gaps or critical design and integration issues. The WREL facility was designed, constructed, and operated under a project selected and co-funded under the Round IV of the United States Department of Energy's (DOE's) Clean Coal Technology Program. In this project, coal and/or other solid fuel feedstocks are gasified in an oxygen-blown, entrained-flow gasifier with continuous slag removal and a dry particulate removal system. The resulting product synthesis gas is used to fuel a combustion turbine generator whose exhaust is integrated with a heat recovery steam generator to drive a refurbished steam turbine generator. The gasifier uses technology initially developed by The Dow Chemical Company (the Destec Gasification Process), and now acquired and offered commercially by COP as the E-GAS{trademark} technology. In a joint effort with the DOE, a Cooperative Agreement was awarded under the Early Entrance Coproduction Plant (EECP) solicitation. GEC, and now COP and the industrial partners are investigating the use of synthesis gas produced by the E-GAS{trademark} technology in a coproduction environment to enhance the efficiency and productivity of solid fuel gasification combined cycle power plants. The objectives of this effort are to determine the feasibility of an EECP located at a specific site which produces some combination of electric power (or heat), fuels, and/or chemicals from synthesis gas derived from coal, or, coal in combination with some other carbonaceous feedstock. The project's intended result is to provide the necessary technical, economic, and environmental information that will be needed to move the EECP forward to detailed design, construction, and operation by industry.

  10. Hydrate-phobic surfaces: fundamental studies in clathrate hydrate adhesion reduction

    E-Print Network [OSTI]

    Smith, J. David

    Clathrate hydrate formation and subsequent plugging of deep-sea oil and gas pipelines represent a significant bottleneck for deep-sea oil and gas operations. Current methods for hydrate mitigation are expensive and energy ...

  11. Simteche Hydrate CO2 Capture Process

    SciTech Connect (OSTI)

    Nexant and Los Alamos National Laboratory

    2006-09-30T23:59:59.000Z

    As a result of an August 4, 2005 project review meeting held at Los Alamos National Laboratory (LANL) to assess the project's technical progress, Nexant/Simteche/LANL project team was asked to meet four targets related to the existing project efforts. The four targets were to be accomplished by the September 30, 2006. These four targets were: (1) The CO{sub 2} hydrate process needs to show, through engineering and sensitivity analysis, that it can achieve 90% CO{sub 2} capture from the treated syngas stream, operating at 1000 psia. The cost should indicate the potential of achieving the Sequestration Program's cost target of less than 10% increase in the cost of electricity (COE) of the non-CO{sub 2} removal IGCC plant or demonstrate a significant cost reduction from the Selexol process cost developed in the Phase II engineering analysis. (2) The ability to meet the 20% cost share requirement for research level efforts. (3) LANL identifies through equilibrium and bench scale testing a once-through 90% CO{sub 2} capture promoter that supports the potential to achieve the Sequestration Program's cost target. Nexant is to perform an engineering analysis case to verify any economic benefits, as needed; no ETM validation is required, however, for this promoter for FY06. (4) The CO{sub 2} hydrate once-through process is to be validated at 1000 psia with the ETM at a CO{sub 2} capture rate of 60% without H{sub 2}S. The performance of 68% rate of capture is based on a batch, equilibrium data with H{sub 2}S. Validation of the test results is required through multiple runs and engineering calculations. Operational issues will be solved that will specifically effect the validation of the technology. Nexant was given the primary responsibility for Target No.1, while Simteche was mainly responsible for Target No.2; with LANL having the responsibility of Targets No.3 and No.4.

  12. Coupling the Alkaline-Surfactant-Polymer Technology and The Gelation Technology to Maximize Oil Production

    SciTech Connect (OSTI)

    Malcolm Pitts; Jie Qi; Dan Wilson; Phil Dowling; David Stewart; Bill Jones

    2005-12-01T23:59:59.000Z

    Gelation technologies have been developed to provide more efficient vertical sweep efficiencies for flooding naturally fractured oil reservoirs or reservoirs with different sand lenses with high permeability contrast. The field proven alkaline-surfactant-polymer technology economically recovers 15% to 25% OOIP more crude oil than waterflooding from swept pore space of an oil reservoir. However, alkaline-surfactant-polymer technology is not amenable to naturally fractured reservoirs or reservoirs with high permeability contrast zones because much of injected solution bypasses target pore space containing oil. This work investigates whether combining these two technologies could broaden applicability of alkaline-surfactant-polymer flooding into these reservoirs. Fluid-fluid interaction with different gel chemical compositions and alkaline-surfactant-polymer solution with pH values ranging from 9.2 to 12.9 have been tested. Aluminum-polyacrylamide gels are not stable to alkaline-surfactant-polymer solutions at any pH. Chromium-polyacrylamide gels with polymer to chromium ion ratios of 25 or greater were stable to alkaline-surfactant-polymer solutions if solution pH was 10.6 or less. When the polymer to chromium ion was 15 or less, chromium-polyacrylamide gels were stable to alkaline-surfactant-polymer solutions with pH values up to 12.9. Chromium-xanthan gum gels were stable to alkaline-surfactant-polymer solutions with pH values of 12.9 at the polymer to chromium ion ratios tested. Silicate-polyacrylamide, resorcinol-formaldehyde, and sulfomethylated resorcinol-formaldehyde gels were also stable to alkaline-surfactant-polymer solutions with pH values ranging from 9.2 to 12.9. Iron-polyacrylamide gels were immediately destroyed when contacted with any of the alkaline-surfactant-polymer solutions with pH values ranging from 9.2 to 12.9. Gel solutions under dynamic conditions of linear corefloods showed similar stability to alkaline-surfactant-polymer solutions as in the fluid-fluid analyses with the exception of the xanthan gum-chromium acetate gels. Aluminum-polyacrylamide flowing gels are not stable to alkaline-surfactant-polymer solutions of either pH 10.5 or 12.9, either in linear corefloods or in dual separate radial core, common manifold corefloods. Chromium acetate-polyacrylamide flowing and rigid tonguing gels are stable to subsequent alkaline-surfactant-polymer solution injection. Rigid tonguing chromium acetate-polyacrylamide gels maintained permeability reduction better than flowing chromium acetate-polyacrylamide gels. Chromium acetate gels were stable to injection of alkaline-surfactant-polymer solutions at 72 F, 125 F and 175 F in linear corefloods. Chromium acetate-polyacrylamide gels maintained diversion capability after injection of an alkaline-surfactant-polymer solution in stacked; radial coreflood with a common well bore. Chromium acetate-polyacrylamide gel used to seal fractured core maintain fracture closure if followed by an alkaline-surfactant-polymer solution. Chromium acetatexanthan gum rigid gels are not stable to subsequent alkaline-surfactant-polymer solution injection at 72, 125, and 175 F. Silicate-polyacrylamide gels are not stable with subsequent injection of either a pH 10.5 or a 12.9 alkaline-surfactant-polymer solution. Resorcinol-formaldehyde gels were stable to subsequent alkaline-surfactant-polymer solution injection. When evaluated in a dual core configuration, injected fluid flows into the core with the greatest effective permeability to the injected fluid. The same gel stability trends to subsequent alkaline-surfactant-polymer injected solution were observed. Aluminum citrate-polyacrylamide, resorcinol-formaldehyde, and the silicate-polyacrylamide gel systems did not produce significant incremental oil in linear corefloods. Both flowing and rigid tonguing chromium acetate-polyacrylamide gels and the xanthan gum-chromium acetate gel system produced incremental oil with the rigid tonguing gel producing the greatest amount. Higher oil recovery could have been due to higher differential

  13. Coupling the Alkaline-Surfactant-Polymer Technology and the Gelation Technology to Maximize Oil Production

    SciTech Connect (OSTI)

    Malcolm Pitts; Jie Qi; Dan Wilson; Phil Dowling; David Stewart; Bill Jones

    2005-12-01T23:59:59.000Z

    Gelation technologies have been developed to provide more efficient vertical sweep efficiencies for flooding naturally fractured oil reservoirs or reservoirs with different sand lenses with high permeability contrast. The field proven alkaline-surfactant-polymer technology economically recovers 15% to 25% OOIP more crude oil than waterflooding froin swept pore space of an oil reservoir. However, alkaline-surfactant-polymer technology is not amenable to naturally fractured reservoirs or reservoirs with high permeability contrast zones because much of injected solution bypasses target pore space containing oil. This work investigates whether combining these two technologies could broaden applicability of alkaline-surfactant-polymer flooding into these reservoirs. Fluid-fluid interaction with different gel chemical compositions and alkaline-surfactant-polymer solution with pH values ranging from 9.2 to 12.9 have been tested. Aluminum-polyacrylamide gels are not stable to alkaline-surfactant-polymer solutions at any pH. Chromium-polyacrylamide gels with polymer to chromium ion ratios of 25 or greater were stable to alkaline-surfactant-polymer solutions if solution pH was 10.6 or less. When the polymer to chromium ion was 15 or less, chromium-polyacrylamide gels were stable to alkaline-surfactant-polymer solutions with pH values up to 12.9. Chromium-xanthan gum gels were stable to alkaline-surfactant-polymer solutions with pH values of 12.9 at the polymer to chromium ion ratios tested. Silicate-polyacrylamide, resorcinol-formaldehyde, and sulfomethylated resorcinol-formaldehyde gels were also stable to alkaline-surfactant-polymer solutions with pH values ranging from 9.2 to 12.9. Iron-polyacrylamide gels were immediately destroyed when contacted with any of the alkaline-surfactant-polymer solutions with pH values ranging from 9.2 to 12.9. Gel solutions under dynamic conditions of linear corefloods showed similar stability to alkaline-surfactant-polymer solutions as in the fluid-fluid analyses with the exception of the xanthan gum-chromium acetate gels. Aluminum-polyacrylamide flowing gels are not stable to alkaline-surfactant-polymer solutions of either pH 10.5 or 12.9, either in linear corefloods or in dual separate radial core, common manifold corefloods. Chromium acetate-polyacrylamide flowing and rigid tonguing gels are stable to subsequent alkaline-surfactant-polymer solution injection. Rigid tonguing chromium acetate-polyacrylamide gels maintained permeability reduction better than flowing chromium acetate-polyacrylamide gels. Chromium acetate gels were stable to injection of alkaline-surfactant-polymer solutions at 72 F, 125 F and 175 F in linear corefloods. Chromium acetate-polyacrylamide gels maintained diversion capability after injection of an alkaline-surfactant-polymer solution in stacked; radial coreflood with a common well bore. Chromium acetate-polyacrylamide gel used to seal fractured core maintain fracture closure if followed by an alkaline-surfactant-polymer solution. Chromium acetate-xanthan gum rigid gels are not stable to subsequent alkaline-surfactant-polymer solution injection at 72, 125, and 175 F. Silicate-polyacrylamide gels are not stable with subsequent injection of either a pH 10.5 or a 12.9 alkaline-surfactant-polymer solution. Resorcinol-formaldehyde gels were stable to subsequent alkaline-surfactant-polymer solution injection. When evaluated in a dual core configuration, injected fluid flows into the core with the greatest effective permeability to the injected fluid. The same gel stability trends to subsequent alkaline-surfactant-polymer injected solution were observed. Aluminum citrate-polyacrylamide, resorcinol-formaldehyde, and the silicate-polyacrylamide gel systems did not produce significant incremental oil in linear corefloods. Both flowing and rigid tonguing chromium acetate-polyacrylamide gels and the xanthan gum-chromium acetate gel system produced incremental oil with the rigid tonguing gel producing the greatest amount. Higher oil recovery could have been due to higher differentia

  14. Productivity genefits from new energy technology: A case study of a paint manufacturing company

    SciTech Connect (OSTI)

    Raghunathan, P.; Capehart, B.L.

    1997-06-01T23:59:59.000Z

    In many cases, implementing new energy efficiency technologies not only helps facilities reduce their energy costs, but it also creates greater profits by increasing productivity. These added benefits from productivity improvements can sometimes be greater than the energy cost savings, and can result in an attractive overall payback period for implementing the new technology. This paper presents a case study of productivity improvement at a paint manufacturing company as a result of implementing new energy efficiency technology. During an industrial energy assessment, it was noted that the company had experienced frequent failures of motor belts and sheaves on five paint mixers resulting in significant replacement costs and labor costs. In addition, a bigger loss was being suffered due to lost potential profit associated with the frequent work stoppages. The IAC recommendation was to install motor soft starters (also known as motor voltage controllers) on the five mixing machines. Installation of soft starters would have the following benefits: lower energy costs, lower replacement costs for transmission components, lower labor costs, and higher production levels and increased profits. The total annual benefits were estimated at $122,659, of which the benefits from increased productivity were nearly $67,000. The overall simple payback period for installing the soft starters was less than 2 months.

  15. Desalination utilizing clathrate hydrates (LDRD final report).

    SciTech Connect (OSTI)

    Simmons, Blake Alexander; Bradshaw, Robert W.; Dedrick, Daniel E.; Cygan, Randall Timothy (Sandia National Laboratories, Albuquerque, NM); Greathouse, Jeffery A. (Sandia National Laboratories, Albuquerque, NM); Majzoub, Eric H. (University of Missouri, Columbia, MO)

    2008-01-01T23:59:59.000Z

    Advances are reported in several aspects of clathrate hydrate desalination fundamentals necessary to develop an economical means to produce municipal quantities of potable water from seawater or brackish feedstock. These aspects include the following, (1) advances in defining the most promising systems design based on new types of hydrate guest molecules, (2) selection of optimal multi-phase reactors and separation arrangements, and, (3) applicability of an inert heat exchange fluid to moderate hydrate growth, control the morphology of the solid hydrate material formed, and facilitate separation of hydrate solids from concentrated brine. The rate of R141b hydrate formation was determined and found to depend only on the degree of supercooling. The rate of R141b hydrate formation in the presence of a heat exchange fluid depended on the degree of supercooling according to the same rate equation as pure R141b with secondary dependence on salinity. Experiments demonstrated that a perfluorocarbon heat exchange fluid assisted separation of R141b hydrates from brine. Preliminary experiments using the guest species, difluoromethane, showed that hydrate formation rates were substantial at temperatures up to at least 12 C and demonstrated partial separation of water from brine. We present a detailed molecular picture of the structure and dynamics of R141b guest molecules within water cages, obtained from ab initio calculations, molecular dynamics simulations, and Raman spectroscopy. Density functional theory calculations were used to provide an energetic and molecular orbital description of R141b stability in both large and small cages in a structure II hydrate. Additionally, the hydrate of an isomer, 1,2-dichloro-1-fluoroethane, does not form at ambient conditions because of extensive overlap of electron density between guest and host. Classical molecular dynamics simulations and laboratory trials support the results for the isomer hydrate. Molecular dynamics simulations show that R141b hydrate is stable at temperatures up to 265K, while the isomer hydrate is only stable up to 150K. Despite hydrogen bonding between guest and host, R141b molecules rotated freely within the water cage. The Raman spectrum of R141b in both the pure and hydrate phases was also compared with vibrational analysis from both computational methods. In particular, the frequency of the C-Cl stretch mode (585 cm{sup -1}) undergoes a shift to higher frequency in the hydrate phase. Raman spectra also indicate that this peak undergoes splitting and intensity variation as the temperature is decreased from 4 C to -4 C.

  16. WABASH RIVER INTEGRATED METHANOL AND POWER PRODUCTION FROM CLEAN COAL TECHNOLOGIES (IMPPCCT)

    SciTech Connect (OSTI)

    Gary Harmond; Albert Tsang

    2003-03-14T23:59:59.000Z

    The Wabash River Integrated Methanol and Power Production from Clean Coal Technologies (IMPPCCT) project is evaluating integrated electrical power generation and methanol production through clean coal technologies. The project is conducted by a multi-industry team lead by Gasification Engineering Corporation (GEC), a company of Global Energy Inc., and supported by Air Products and Chemicals, Inc., Dow Chemical Company, Dow Corning Corporation, Methanex Corporation, and Siemens Westinghouse Power Corporation. Three project phases are planned for execution over a three year period, including: (1) Feasibility study and conceptual design for an integrated demonstration facility, and for fence-line commercial embodiment plants (CEP) operated at Dow Chemical or Dow Corning chemical plant locations (2) Research, development, and testing to define any technology gaps or critical design and integration issues (3) Engineering design and financing plan to install an integrated commercial demonstration facility at the existing Wabash River Energy Limited (WREL) plant in West Terre Haute, Indiana. The WREL facility is a project selected and co-funded under the Round IV of the U.S. Department of Energy's (DOE's) Clean Coal Technology Program. In this project, coal and/or other solid fuel feedstocks are gasified in an oxygen-blown, entrained-flow gasifier with continuous slag removal and a dry particulate removal system. The resulting product synthesis gas is used to fuel a combustion turbine generator whose exhaust is integrated with a heat recovery steam generator to drive a refurbished steam turbine generator. The gasifier uses technology initially developed by The Dow Chemical Company (the Destec Gasification Process), and now offered commercially by Global Energy, Inc., as the E-GAS{trademark} technology. In a joint effort with the DOE, a Cooperative Agreement was awarded under the Early Entrance Coproduction Plant (EECP) solicitation. GEC and an Industrial Consortium are investigating the use of synthesis gas produced by the E-GAS{trademark} technology in a coproduction environment to enhance the efficiency and productivity of solid fuel gasification combined cycle power plants. During the reporting period, various methods to remove low-level contaminants for the synthesis gas were reviewed. In addition, there was a transition of the project personnel for GEC which has slowed the production of the outstanding project reports.

  17. Initial queries into the notion of Power Users of Technology -Investigating ideas of production, competence and identity

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    ' or young people's1 use of technology. What distinguishes the Power User research initiative and makes1 Initial queries into the notion of Power Users of Technology - Investigating ideas of production, which I find very important in order to un- derstand the notion of "Power Users of Technology

  18. New insights into water bonding during early tricalcium silicate hydration with quasielastic neutron scattering

    SciTech Connect (OSTI)

    Gutberlet, T., E-mail: gutberlet@cbm.bv.tum.de [Centre for Building Materials (CBM), Technische Universität München, Baumbachstraße 7, 81245 Munich (Germany); Hilbig, H.; Beddoe, R.E. [Centre for Building Materials (CBM), Technische Universität München, Baumbachstraße 7, 81245 Munich (Germany)] [Centre for Building Materials (CBM), Technische Universität München, Baumbachstraße 7, 81245 Munich (Germany); Lohstroh, W. [Forschungs-Neutronenquelle Heinz Maier-Leibnitz (FRM II), Technische Universität München, Lichtenbergstraße 1, 85748 Garching (Germany)] [Forschungs-Neutronenquelle Heinz Maier-Leibnitz (FRM II), Technische Universität München, Lichtenbergstraße 1, 85748 Garching (Germany)

    2013-09-15T23:59:59.000Z

    New information on the water bonding during the first 36 h of hydration of tricalcium silicate was obtained using the high neutron flux at the sample position of the time-of-flight spectrometer (TOFTOF), FRM II in Garching, Germany, together with {sup 29}Si NMR and X-ray diffraction measurements. A rapid increase in the amount of constrained water was observed at the beginning of the induction period. This is attributed to the formation of an early C-S-H with a large specific surface area (around 800 m{sup 2}/g). During subsequent hydration, the amount of constrained water, as given by the total surface area of the hydration products, is controlled by (a) the formation of new metastable early C-S-H which increases total surface area and (b) polymerisation processes which reduce total surface area. The relative contribution of these processes varies during hydration.

  19. TREATMENT OF METAL-LADEN HAZARDOUS WASTES WITH ADVANCED CLEAN COAL TECHNOLOGY BY-PRODUCTS

    SciTech Connect (OSTI)

    James T. Cobb, Jr.; Ronald D. Neufeld; Jana Agostini

    1999-05-10T23:59:59.000Z

    This fourteenth quarterly report describes work done during the fourteenth three-month period of the University of Pittsburgh's project on the ''Treatment of Metal-Laden Hazardous Wastes with Advanced Clean Coal Technology By-Products.'' This report describes the activities of the project team during the reporting period. The principal work has focused upon new laboratory evaluation of samples from Phase 1, discussions with MAX Environmental Technologies, Inc., on the field work of Phase 2, preparing presentations, and making and responding to two outside contacts.

  20. Microstructural Response of Variably Hydrated Ca-Rich Montmorillonite...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Microstructural Response of Variably Hydrated Ca-Rich Montmorillonite to Supercritical CO2. Microstructural Response of Variably Hydrated Ca-Rich Montmorillonite to Supercritical...

  1. aluminate cements hydration: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    early stage hydration of different classes of oilwell cement Bentz, Dale P. 5 NISTIR 7232 CEMHYD3D: A Three-Dimensional Cement Hydration Engineering Websites Summary: NISTIR...

  2. Stepwise hydration of the cyanide anion: A temperature-controlled...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Stepwise hydration of the cyanide anion: A temperature-controlled photoelectron spectroscopy and ab initio computational study Stepwise hydration of the cyanide anion: A...

  3. Wabash River Integrated Methanol and Power Production from Clean Coal Technologies (IMPPCCT)

    SciTech Connect (OSTI)

    Conocophillips

    2007-09-30T23:59:59.000Z

    The Wabash River Integrated Methanol and Power Production from Clean Coal Technologies (IMPPCCT) project was established to evaluate integrated electrical power generation and methanol production through clean coal technologies. The project was under the leadership of ConocoPhillips Company (COP), after it acquired Gasification Engineering Corporation (GEC) and the E-Gas gasification technology from Global Energy Inc. in July 2003. The project has completed both Phase 1 and Phase 2 of development. The two project phases include the following: (1) Feasibility study and conceptual design for an integrated demonstration facility at SG Solutions LLC (SGS), previously the Wabash River Energy Limited, Gasification Facility located in West Terre Haute, Indiana, and for a fence-line commercial embodiment plant (CEP) operated at the Dow Chemical Company or Dow Corning Corporation chemical plant locations. (2) Research, development, and testing (RD&T) to define any technology gaps or critical design and integration issues. Phase 1 of this project was supported by a multi-industry team consisting of Air Products and Chemicals, Inc., The Dow Chemical Company, Dow Corning Corporation, Methanex Corporation, and Siemens Westinghouse Power Corporation, while Phase 2 was supported by Gas Technology Institute, TDA Research Inc., and Nucon International, Inc. The SGS integrated gasification combined cycle (IGCC) facility was designed, constructed, and operated under a project selected and co-funded under the Round IV of the United States Department of Energy's (DOE's) Clean Coal Technology Program. In this project, coal and/or other carbonaceous fuel feedstocks are gasified in an oxygen-blown, entrained-flow gasifier with continuous slag removal and a dry particulate removal system. The resulting product synthesis gas (syngas) is used to fuel a combustion turbine generator whose exhaust is integrated with a heat recovery steam generator to drive a refurbished steam turbine generator. The gasifier uses technology initially developed by The Dow Chemical Company (the Destec Gasification Process), and now acquired and offered commercially by COP as the E-Gas technology. In a joint effort with the DOE, a Cooperative Agreement was awarded under the Early Entrance Coproduction Plant (EECP) solicitation. GEC, and later COP and the industrial partners investigated the use of syngas produced by the E-Gas technology in a coproduction environment to enhance the efficiency and productivity of solid fuel gasification combined cycle power plants. The objectives of this effort were to determine the feasibility of an EECP located at a specific site which produces some combination of electric power (or heat), fuels, and/or chemicals from syngas derived from coal, or, coal in combination with some other carbonaceous feedstock. The intended result of the project was to provide the necessary technical, economic, and environmental information that would be needed to move the EECP forward to detailed design, construction, and operation by industry. The EECP study conducted in Phase 1 of the IMPPCCT Project confirmed that the concept for the integration of gasification-based (E-Gas) electricity generation from coal and/or petroleum coke and methanol production (Liquid Phase Methanol or LPMEOH{trademark}) processes was feasible for the coproduction of power and chemicals. The results indicated that while there were minimal integration issues that impact the deployment of an IMPPCCT CEP, the major concern was the removal of sulfur and other trace contaminants, which are known methanol catalyst poisons, from the syngas. However, economic concerns in the domestic methanol market which is driven by periodic low natural gas prices and cheap offshore supplies limit the commercial viability of this more capital intensive concept. The objective of Phase 2 was to conduct RD&T as outlined in the Phase 1 RD&T Plan to enhance the development and commercial acceptance of coproduction technology. Studies were designed to address the technical concerns that would mak

  4. Advanced Gas Storage Concepts: Technologies for the Future

    SciTech Connect (OSTI)

    Freeway, Katy (PB-KBB Inc.); Rogers, R.E. (Mississippi State University); DeVries, Kerry L.; Nieland, Joel D.; Ratigan, Joe L.; Mellegard, Kirby D. (RESPEC)

    2000-02-01T23:59:59.000Z

    This full text product includes: 1) A final technical report titled Advanced Underground Gas Storage Concepts, Refrigerated-Mined Cavern Storage and presentations from two technology transfer workshops held in 1998 in Houston, Texas, and Pittsburgh, Pennsylvania (both on the topic of Chilled Gas Storage in Mined Caverns); 2) A final technical report titled Natural Gas Hydrates Storage Project, Final Report 1 October 1997 - 31 May 1999; 3) A final technical report titled Natural Gas Hydrates Storage Project Phase II: Conceptual Design and Economic Study, Final Report 9 June - 10 October 1999; 4) A final technical report titled Commerical Potential of Natural Gas Storage in Lined Rock Caverns (LRC) and presentations from a DOE-sponsored workshop on Alternative Gas Storage Technologies, held Feb 17, 2000 in Pittsburgh, PA; and 5) Phase I and Phase II topical reports titled Feasibility Study for Lowering the Minimum Gas Pressure in Solution-Mined Caverns Based on Geomechanical Analyses of Creep-Induced Damage and Healing.

  5. Diffusion of CO2 During Hydrate Formation and Dissolution

    SciTech Connect (OSTI)

    Franklin M. Orr, Jr.

    2002-08-20T23:59:59.000Z

    Experiments were performed to measure the rate of diffusion of CO2 through hydrate films. Hydrate films were created in a capillary tube, and the growth of the hydrate film was measured. Difficulties were encountered in creating hydrate repeatedly, and some non-uniform growth of the films was observed. Sufficient observations were obtained to demonstrate that hydrate growth occurs preferentially on the hydrate/water side of the interface, rather than at the hydrate/CO2 interface. Diffusion coefficients were estimated from observations of the rate of growth of the hydrate film along with estimates of the solubility of CO2 in water and of the concentration gradient across the hydrate layer. The experimental observations indicate that hydrate formation occurs much more rapidly at the hydrate water interface than at the hydrate/CO2 interface. Any growth of hydrate at the CO2/hydrate interface was too slow to be observed at the time scale of the experiments. That observation is consistent with the idea that CO2 can move more easily through the hydrate, presumably by hopping between hydrate cages, than water can move through the hydrate, presumably by lattice hopping. Estimated diffusion coefficients were in the range 1-3E-06 cm2/sec. Those values are about an order of magnitude lower than the diffusion coefficient for CO2 in liquid water, but four orders of magnitude larger than the value for diffusion of CO2 in a solid. The rate of diffusion through the hydrate controls both the creation of new hydrate at the hydrate/water interface and the rate at which CO2 dissolves in the liquid water and diffuses away from the hydrate layer. Formation of a hydrate layer reduces the rate at which CO2 dissolves in liquid water.

  6. A wide variety of injection molding technologies is now applicable to small series and mass production

    SciTech Connect (OSTI)

    Bloß, P., E-mail: bloss@kuz-leipzig.de, E-mail: juettner@kuz-leipzig.de, E-mail: jacob@kuz-leipzig.de, E-mail: loeser@kuz-leipzig.de, E-mail: michaelis@kuz-leipzig.de, E-mail: krajewsky@kuz-leipzig.de; Jüttner, G., E-mail: bloss@kuz-leipzig.de, E-mail: juettner@kuz-leipzig.de, E-mail: jacob@kuz-leipzig.de, E-mail: loeser@kuz-leipzig.de, E-mail: michaelis@kuz-leipzig.de, E-mail: krajewsky@kuz-leipzig.de; Jacob, S., E-mail: bloss@kuz-leipzig.de, E-mail: juettner@kuz-leipzig.de, E-mail: jacob@kuz-leipzig.de, E-mail: loeser@kuz-leipzig.de, E-mail: michaelis@kuz-leipzig.de, E-mail: krajewsky@kuz-leipzig.de; Löser, C., E-mail: bloss@kuz-leipzig.de, E-mail: juettner@kuz-leipzig.de, E-mail: jacob@kuz-leipzig.de, E-mail: loeser@kuz-leipzig.de, E-mail: michaelis@kuz-leipzig.de, E-mail: krajewsky@kuz-leipzig.de; Michaelis, J., E-mail: bloss@kuz-leipzig.de, E-mail: juettner@kuz-leipzig.de, E-mail: jacob@kuz-leipzig.de, E-mail: loeser@kuz-leipzig.de, E-mail: michaelis@kuz-leipzig.de, E-mail: krajewsky@kuz-leipzig.de; Krajewsky, P., E-mail: bloss@kuz-leipzig.de, E-mail: juettner@kuz-leipzig.de, E-mail: jacob@kuz-leipzig.de, E-mail: loeser@kuz-leipzig.de, E-mail: michaelis@kuz-leipzig.de, E-mail: krajewsky@kuz-leipzig.de [Kunststoff-Zentrum in Leipzig gGmbH (KuZ), Leipzig (Germany)

    2014-05-15T23:59:59.000Z

    Micro plastic parts open new fields for application, e. g., to electronics, sensor technologies, optics, and medical engineering. Before micro parts can go to mass production, there is a strong need of having the possibility for testing different designs and materials including material combinations. Hence, flexible individual technical and technological solutions for processing are necessary. To manufacture high quality micro parts, a micro injection moulding machine named formicaPlast based on a two-step plunger injection technology was developed. Resulting from its design, the residence time and the accuracy problems for managing small shot volumes with reproducible high accuracy are uncompromisingly solved. Due to their simple geometry possessing smooth transitions and non adherent inner surfaces, the plunger units allow to process 'all' thermoplastics from polyolefines to high performance polymers, optical clear polymers, thermally sensitive bioresorbables, highly filled systems (the so-called powder injection molding PIM), and liquid silicon rubber (LSR, here with a special kit). The applied platform strategy in the 1K and 2K version allows integrating automation for assembling, handling and packaging. A perpendicular arrangement allows encapsulation of inserts, also partially, and integration of this machine into process chains. Considering a wide variety of different parts consisting of different materials, the high potential of the technology is demonstrated. Based on challenging industrial parts from electronic applications (2K micro MID and bump mat, where both are highly structured parts), the technological solutions are presented in more detail.

  7. Gas Hydrate Storage of Natural Gas

    SciTech Connect (OSTI)

    Rudy Rogers; John Etheridge

    2006-03-31T23:59:59.000Z

    Environmental and economic benefits could accrue from a safe, above-ground, natural-gas storage process allowing electric power plants to utilize natural gas for peak load demands; numerous other applications of a gas storage process exist. A laboratory study conducted in 1999 to determine the feasibility of a gas-hydrates storage process looked promising. The subsequent scale-up of the process was designed to preserve important features of the laboratory apparatus: (1) symmetry of hydrate accumulation, (2) favorable surface area to volume ratio, (3) heat exchanger surfaces serving as hydrate adsorption surfaces, (4) refrigeration system to remove heat liberated from bulk hydrate formation, (5) rapid hydrate formation in a non-stirred system, (6) hydrate self-packing, and (7) heat-exchanger/adsorption plates serving dual purposes to add or extract energy for hydrate formation or decomposition. The hydrate formation/storage/decomposition Proof-of-Concept (POC) pressure vessel and supporting equipment were designed, constructed, and tested. This final report details the design of the scaled POC gas-hydrate storage process, some comments on its fabrication and installation, checkout of the equipment, procedures for conducting the experimental tests, and the test results. The design, construction, and installation of the equipment were on budget target, as was the tests that were subsequently conducted. The budget proposed was met. The primary goal of storing 5000-scf of natural gas in the gas hydrates was exceeded in the final test, as 5289-scf of gas storage was achieved in 54.33 hours. After this 54.33-hour period, as pressure in the formation vessel declined, additional gas went into the hydrates until equilibrium pressure/temperature was reached, so that ultimately more than the 5289-scf storage was achieved. The time required to store the 5000-scf (48.1 hours of operating time) was longer than designed. The lower gas hydrate formation rate is attributed to a lower heat transfer rate in the internal heat exchanger than was designed. It is believed that the fins on the heat-exchanger tubes did not make proper contact with the tubes transporting the chilled glycol, and pairs of fins were too close for interior areas of fins to serve as hydrate collection sites. A correction of the fabrication fault in the heat exchanger fin attachments could be easily made to provide faster formation rates. The storage success with the POC process provides valuable information for making the process an economically viable process for safe, aboveground natural-gas storage.

  8. WABASH RIVER INTEGRATED METHANOL AND POWER PRODUCTION FROM CLEAN COAL TECHNOLOGIES (IMPPCCT)

    SciTech Connect (OSTI)

    Albert Tsang

    2003-03-14T23:59:59.000Z

    The Wabash River Integrated Methanol and Power Production from Clean Coal Technologies (IMPPCCT) project is evaluating integrated electrical power generation and methanol production through clean coal technologies. The project is conducted by a multi-industry team lead by Gasification Engineering Corporation (GEC), and supported by Air Products and Chemicals, Inc., Dow Chemical Company, Dow Corning Corporation, Methanex Corporation, and Siemens Westinghouse Power Corporation. Three project phases are planned for execution, including: (1) Feasibility study and conceptual design for an integrated demonstration facility, and for fence-line commercial embodiment plants (CEP) operated at Dow Chemical or Dow Corning chemical plant locations (2) Research, development, and testing (RD&T) to define any technology gaps or critical design and integration issues (3) Engineering design and financing plan to install an integrated commercial demonstration facility at the existing Wabash River Energy Limited (WREL) plant in West Terre Haute, Indiana. The WREL facility is a project selected and co-funded under the Round IV of the United States Department of Energy's (DOE's) Clean Coal Technology Program. In this project, coal and/or other solid fuel feedstocks are gasified in an oxygen-blown, entrained-flow gasifier with continuous slag removal and a dry particulate removal system. The resulting product synthesis gas is used to fuel a combustion turbine generator whose exhaust is integrated with a heat recovery steam generator to drive a refurbished steam turbine generator. The gasifier uses technology initially developed by The Dow Chemical Company (the Destec Gasification Process), and now offered commercially by Global Energy, Inc., parent company of GEC and WREL, as the E-GAS{trademark} technology. In a joint effort with the DOE, a Cooperative Agreement was awarded under the Early Entrance Coproduction Plant (EECP) solicitation. GEC and an Industrial Consortium are investigating the use of synthesis gas produced by the E-GAS{trademark} technology in a coproduction environment to enhance the efficiency and productivity of solid fuel gasification combined cycle power plants. The objectives of this effort are to determine the feasibility of an EECP located at a specific site which produces some combination of electric power (or heat), fuels, and/or chemicals from synthesis gas derived from coal, or, coal in combination with some other carbonaceous feedstock. The project's intended result is to provide the necessary technical, economic, and environmental information that will be needed to move the EECP forward to detailed design, construction, and operation by industry. During the reporting period, effort continues on identifying potential technologies for removing contaminants from synthesis gas to the level required by methanol synthesis. A liquid phase Claus process and a direct sulfur oxidation process were evaluated. Preliminary discussion was held with interested parties on cooperating on RD&T in Phase II of the project. Also, significant progress was made during the period in the submission of project deliverables. A meeting was held at DOE's National Energy Technology Laboratory in Morgantown between GEC and the DOE IMPPCCT Project Manager on the status of the project, and reached an agreement on the best way to wrap up Phase I and transition into the Phase II RD&T. Potential projects for the Phase II, cost, and fund availability were also discussed.

  9. GAS METHANE HYDRATES-RESEARCH STATUS, ANNOTATED BIBLIOGRAPHY, AND ENERGY IMPLICATIONS

    SciTech Connect (OSTI)

    James Sorensen; Jaroslav Solc; Bethany Bolles

    2000-07-01T23:59:59.000Z

    The objective of this task as originally conceived was to compile an assessment of methane hydrate deposits in Alaska from available sources and to make a very preliminary evaluation of the technical and economic feasibility of producing methane from these deposits for remote power generation. Gas hydrates have recently become a target of increased scientific investigation both from the standpoint of their resource potential to the natural gas and oil industries and of their positive and negative implications for the global environment After we performed an extensive literature review and consulted with representatives of the U.S. Geological Survey (USGS), Canadian Geological Survey, and several oil companies, it became evident that, at the current stage of gas hydrate research, the available information on methane hydrates in Alaska does not provide sufficient grounds for reaching conclusions concerning their use for energy production. Hence, the original goals of this task could not be met, and the focus was changed to the compilation and review of published documents to serve as a baseline for possible future research at the Energy & Environmental Research Center (EERC). An extensive annotated bibliography of gas hydrate publications has been completed. The EERC will reassess its future research opportunities on methane hydrates to determine where significant initial contributions could be made within the scope of limited available resources.

  10. Gas Hydrates Research Programs: An International Review

    SciTech Connect (OSTI)

    Jorge Gabitto; Maria Barrufet

    2009-12-09T23:59:59.000Z

    Gas hydrates sediments have the potential of providing a huge amount of natural gas for human use. Hydrate sediments have been found in many different regions where the required temperature and pressure conditions have been satisfied. Resource exploitation is related to the safe dissociation of the gas hydrate sediments. Basic depressurization techniques and thermal stimulation processes have been tried in pilot efforts to exploit the resource. There is a growing interest in gas hydrates all over the world due to the inevitable decline of oil and gas reserves. Many different countries are interested in this valuable resource. Unsurprisingly, developed countries with limited energy resources have taken the lead in worldwide gas hydrates research and exploration. The goal of this research project is to collect information in order to record and evaluate the relative strengths and goals of the different gas hydrates programs throughout the world. A thorough literature search about gas hydrates research activities has been conducted. The main participants in the research effort have been identified and summaries of their past and present activities reported. An evaluation section discussing present and future research activities has also been included.

  11. The hydration mechanism of ketene: 15 years later

    E-Print Network [OSTI]

    Nguyen, Minh Tho

    the self-consistent reaction field method (SCRF) and the polarizable continuum model (PCM). The hydration

  12. IMPROVEMENT OF METHANE STORAGE IN ACTIVATED CARBON USING METHANE HYDRATE

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    it to a gas hydrate formation. In fact, the gas hydrate formation in the remaining free porosity after manuscript, published in "Fifth International Conference on Gas Hydrates (ICGH 5),, Tromdheim : Norway (2005IMPROVEMENT OF METHANE STORAGE IN ACTIVATED CARBON USING METHANE HYDRATE M.L. Zanota(1) , L. Perier

  13. Adiabatic Heat of Hydration Calorimetric Measurements for Reference Saltstone Waste

    SciTech Connect (OSTI)

    Bollinger, James

    2006-01-12T23:59:59.000Z

    The production of nuclear materials for weapons, medical, and space applications from the mid-1950's through the late-1980's at the Savannah River Site (SRS) generated approximately 35 million gallons of liquid high-level radioactive waste, which is currently being processed into vitrified glass for long-term storage. Upstream of the vitrification process, the waste is separated into three components: high activity insoluble sludge, high activity insoluble salt, and very low activity soluble salts. The soluble salt represents 90% of the 35 million gallons of overall waste and is processed at the SRS Saltstone Facility, where it mixed with cement, blast furnace slag, and flyash, creating a grout-like mixture. The resulting grout is pumped into aboveground storage vaults, where it hydrates into concrete monoliths, called saltstone, thus immobilizing the low-level radioactive salt waste. As the saltstone hydrates, it generates heat that slowly diffuses out of the poured material. To ensure acceptable grout properties for disposal and immobilization of the salt waste, the grout temperature must not exceed 95 C during hydration. Adiabatic calorimetric measurements of the heat generated for a representative sample of saltstone were made to determine the time-dependent heat source term. These measurements subsequently were utilized as input to a numerical conjugate heat transfer model to determine the expected peak temperatures for the saltstone vaults.

  14. Additives and method for controlling clathrate hydrates in fluid systems

    DOE Patents [OSTI]

    Sloan, E.D. Jr.; Christiansen, R.L.; Lederhos, J.P.; Long, J.P.; Panchalingam, V.; Du, Y.; Sum, A.K.W.

    1997-06-17T23:59:59.000Z

    Discussed is a process for preventing clathrate hydrate masses from detrimentally impeding the possible flow of a fluid susceptible to clathrate hydrate formation. The process is particularly useful in the natural gas and petroleum production, transportation and processing industry where gas hydrate formation can cause serious problems. Additives preferably contain one or more five member, six member and/or seven member cyclic chemical groupings. Additives include polymers having lactam rings. Additives can also contain polyelectrolytes that are believed to improve conformance of polymer additives through steric hindrance and/or charge repulsion. Also, polymers having an amide on which a C{sub 1}-C{sub 4} group is attached to the nitrogen and/or the carbonyl carbon of the amide may be used alone, or in combination with ring-containing polymers for enhanced effectiveness. Polymers having at least some repeating units representative of polymerizing at least one of an oxazoline, an N-substituted acrylamide and an N-vinyl alkyl amide are preferred.

  15. Additives and method for controlling clathrate hydrates in fluid systems

    DOE Patents [OSTI]

    Sloan, Jr., Earle Dendy (Golden, CO); Christiansen, Richard Lee (Littleton, CO); Lederhos, Joseph P. (Wheatridge, CO); Long, Jin Ping (Dallas, TX); Panchalingam, Vaithilingam (Lakewood, CO); Du, Yahe (Golden, CO); Sum, Amadeu Kun Wan (Golden, CO)

    1997-01-01T23:59:59.000Z

    Discussed is a process for preventing clathrate hydrate masses from detrimentally impeding the possible flow of a fluid susceptible to clathrate hydrate formation. The process is particularly useful in the natural gas and petroleum production, transportation and processing industry where gas hydrate formation can cause serious problems. Additives preferably contain one or more five member, six member and/or seven member cyclic chemical groupings. Additives include polymers having lactam rings. Additives can also contain polyelectrolytes that are believed to improve conformance of polymer additives through steric hinderance and/or charge repulsion. Also, polymers having an amide on which a C.sub.1 -C.sub.4 group is attached to the nitrogen and/or the carbonyl carbon of the amide may be used alone, or in combination with ring-containing polymers for enhanced effectiveness. Polymers having at least some repeating units representative of polymerizing at least one of an oxazoline, an N-substituted acrylamide and an N-vinyl alkyl amide are preferred.

  16. WABASH RIVER INTEGRATED METHANOL AND POWER PRODUCTION FROM CLEAN COAL TECHNOLOGIES (IMPPCCT)

    SciTech Connect (OSTI)

    Doug Strickland; Albert Tsang

    2002-10-14T23:59:59.000Z

    The Wabash River Integrated Methanol and Power Production from Clean Coal Technologies (IMPPCCT) project is evaluating integrated electrical power generation and methanol production through clean coal technologies. The project is conducted by a multi-industry team lead by Gasification Engineering Corporation (GEC), and supported by Air Products and Chemicals, Inc., Dow Chemical Company, Dow Corning Corporation, Methanex Corporation, and Siemens Westinghouse Power Corporation. Three project phases are planned for execution over a three year period, including: (1) Feasibility study and conceptual design for an integrated demonstration facility, and for fence-line commercial plants operated at Dow Chemical or Dow Corning chemical plant locations; (2) Research, development, and testing to define any technology gaps or critical design and integration issues; and (3) Engineering design and financing plan to install an integrated commercial demonstration facility at the existing Wabash River Energy Limited (WREL) plant in West Terre Haute, Indiana. This report describes management planning, work breakdown structure development, and feasibility study activities by the IMPPCCT consortium in support of the first project phase. Project planning activities have been completed, and a project timeline and task list has been generated. Requirements for an economic model to evaluate the West Terre Haute implementation and for other commercial implementations are being defined. Specifications for methanol product and availability of local feedstocks for potential commercial embodiment plant sites have been defined. The WREL facility is a project selected and co-funded under the fifth phase solicitation of the U.S. Department of Energy's Clean Coal Technology Program. In this project, coal and/or other solid fuel feedstocks are gasified in an oxygen-blown, entrained-flow gasifier with continuous slag removal and a dry particulate removal system. The resulting product synthesis gas is used to fuel a combustion turbine generator whose exhaust is integrated with a heat recovery steam generator to drive a refurbished steam turbine generator. The gasifier uses technology initially developed by The Dow Chemical Company (the Destec Gasification Process), and now offered commercially by Global Energy, Inc., as the E-GAS{trademark} technology. In a joint effort with the U.S. Department of Energy, working under a Cooperative Agreement Award from the ''Early Entrance Coproduction Plant'' (EECP) initiative, the GEC and an Industrial Consortia are investigating the application of synthesis gas from the E-GAS{trademark} technology to a coproduction environment to enhance the efficiency and productivity of solid fuel gasification combined cycle power plants. The objectives of this effort are to determine the feasibility of an EECP located at a specific site which produces some combination of electric power (or heat), fuels, and/or chemicals from synthesis gas derived from coal, or, coal in combination with some other carbonaceous feedstock. The project's intended result is to provide the necessary technical, economic, and environmental information that will be needed to move the EECP forward to detailed design, construction, and operation by industry.

  17. Dipolar response of hydrated proteins

    E-Print Network [OSTI]

    Dmitry V. Matyushov

    2011-08-12T23:59:59.000Z

    The paper presents an analytical theory and numerical simulations of the dipolar response of hydrated proteins. The effective dielectric constant of the solvated protein, representing the average dipole moment induced at the protein by a uniform external field, shows a remarkable variation among the proteins studied by numerical simulations. It changes from 0.5 for ubiquitin to 640 for cytochrome c. The former value implies a negative dipolar susceptibility of ubiquitin, that is a dia-electric dipolar response and negative dielectrophoresis. It means that a protein carrying an average dipole of ~240 D is expected to repel from the region of a stronger electric field. This outcome is the result of a negative cross-correlation between the protein and water dipoles, compensating for the positive variance of the protein dipole in the overall dipolar susceptibility. This phenomenon can be characterized as overscreening of protein's dipole by the hydration shell. In contrast to the neutral ubiquitin, charged proteins studied here show para-electric dipolar response and positive dielectrophoresis. The protein-water dipolar cross-correlations are long-ranged, extending approximately 2 nm from the protein surface into the bulk. The analysis of numerical simulations suggests that the polarization of the protein-water interface is strongly affected by the distribution of the protein surface charge. This component of the protein dipolar response gains in importance for high frequencies, above the protein Debye peak, when the response of the protein dipole becomes dynamically arrested. The interface response found in simulations suggests a possibility of a positive increment of the high-frequency dielectric constant of the solution compared to the dielectric constant of the solvent, in support of the observed THz absorbance of protein solutions.

  18. AISI/DOE Technology Roadmap Program: A Technology of Low Coal Rate and High Productivity of RHF Ironmaking

    SciTech Connect (OSTI)

    Wei-Kao Lu

    2002-09-15T23:59:59.000Z

    An economical and environment-friendly ironmaking process based on heating the chemiexecy self-sufficient green balls of iron ore and coal in a hearth furnace is being developed with financial support from AISI members and DOE. DRI, which is hot (1400 C), dense (3.2 g/cm) and of high degree of metallization (95%), has been produced in laboratory and in a pilot plant in Genoa, Italy. Products of such quality have been made from American and Brazilian ores, BOF sludge, EAF dust/BOF sludge mixtures and millscale. The removal of zinc and lead from green balls by this process is essentially complete. In comparison with typical blast furnace operation, the new technology with a melter would have a lower total coal rate by 200kg.THM. The elimination of cokemaking and high temperature agglomeration steps, and a simpler gas handling system would lead to lower capital and operating costs. In comparison with commercial RHF practice it is different in atmosphere (fully oxidized at 1600 to 1650 C), in bed height (120 mm instead of 20-25 mm) and in pellet composition (much less coal but of higher VM). The combined effect leads to three times higher furnace productivity, lower coal consumption and superior DRI quality. The risk of re-oxidation (slag formation) and dusty operation are practiexecy eliminated. The process is stable, tolerant and independent of the size, shape and movement of the hearth. However, materials handling (e.g., discharge of hot DRI) and the exact energy savings have to be established in a larger furnace, straight or rotary, and in a continuous mode of operation.

  19. Long-Term Column Leaching of Phase II Mercury Control Technology By-Products

    SciTech Connect (OSTI)

    Schroeder, K.T.; Cardone, C.R.; White, Fredrick; Rohar, P.C.; Kim, A.G

    2007-07-01T23:59:59.000Z

    An NETL research, development and demonstration program under DOE/Fossil Energy Innovations for Existing Plants is directed toward the improvement of the performance and economics of mercury control from coal-fired plants. The current Phase II of the RD&D program emphasizes the evaluation of performance and cost of control technologies through slip-stream and full scale field testing while continuing the development of novel concepts. One of the concerns of the NETL program is the fate of the captured flue gas mercury which is transferred to the condensed phase by-product stream. The stability of mercury and any co-captured elements in the by-products could have a large economic impact if it reduced by-product sales or increasing their disposal costs. As part of a greater characterization effort of Phase II facility baseline and control technology sample pairs, NETL in-house laboratories have performed continuous leaching of a select subset of the available sample pairs using four leachants: water (pH=5.7), dilute sulfuric acid (pH=1.2), dilute acetic acid (pH=2.9), and sodium carbonate (pH=11.1). This report describes results obtained for mercury, arsenic, and selenium during the 5-month leaching experiments.

  20. Increasing Heavy Oil Reserves in the Wilmington Oil Field Through Advanced Reservoir Characterization and Thermal Production Technologies, Class III

    SciTech Connect (OSTI)

    City of Long Beach; Tidelands Oil Production Company; University of Southern California; David K. Davies and Associates

    2002-09-30T23:59:59.000Z

    The objective of this project was to increase the recoverable heavy oil reserves within sections of the Wilmington Oil Field, near Long Beach, California through the testing and application of advanced reservoir characterization and thermal production technologies. The successful application of these technologies would result in expanding their implementation throughout the Wilmington Field and, through technology transfer, to other slope and basin clastic (SBC) reservoirs.

  1. Increasing Heavy Oil Reserves in the Wilmington Oil Field Through Advanced Reservoir Characterization and Thermal Production Technologies, Class III

    SciTech Connect (OSTI)

    City of Long Beach; Tidelands Oil Production Company; University of Southern California; David K. Davies and Associates

    2002-09-30T23:59:59.000Z

    The objective of this project was to increase the recoverable heavy oil reserves within sections of the Wilmington Oil Field, near Long Beach, California through the testing and application of advanced reservoir characterization and thermal production technologies. It was hoped that the successful application of these technologies would result in their implementation throughout the Wilmington Field and, through technology transfer, will be extended to increase the recoverable oil reserves in other slope and basin clastic (SBC) reservoirs.

  2. DOE/Fossil Energy`s drilling, completion, and stimulation RD&D: A technologies/products overview

    SciTech Connect (OSTI)

    Duda, J.R.; Yost, A.B. II

    1995-12-31T23:59:59.000Z

    An overview of natural gas drilling, completion, and stimulation RD&D sponsored by the US Department of Energy is reported in this paper. Development of high rate-of-penetration drilling systems and underbalanced drilling technologies are detailed among other RD&D activities. The overview serves as a technology transfer medium and is intended to accelerate the deployment of the products and technologies described.

  3. Nanomechanical properties of hydrated organic thin films

    E-Print Network [OSTI]

    Choi, Jae Hyeok

    2007-01-01T23:59:59.000Z

    Hydrated organic thin films are biological or synthetic molecularly thin coatings which impart a particular functionality to an underlying substrate and which have discrete water molecules associated with them. Such films ...

  4. A realistic molecular model of cement hydrates

    E-Print Network [OSTI]

    Ulm, Franz-Josef

    Despite decades of studies of calcium-silicate-hydrate (C-S-H), the structurally complex binder phase of concrete, the interplay between chemical composition and density remains essentially unexplored. Together these ...

  5. MethaneHydrateRD_FC.indd

    Office of Environmental Management (EM)

    source of natural gas in 1983. The Methane Hydrate Research and Development Act of 2000 established DOE as the lead U.S. agency for R&D in this fi eld. Early phases of...

  6. Metal-Catalyzed Hydration of 2-Pyridyloxirane

    E-Print Network [OSTI]

    Hanzlik, Robert P.; Michaely, William J.

    1975-01-01T23:59:59.000Z

    In the presence of CuII the hydration of 2-pyridyloxiran is accelerated 18,000-fold, and its reaction with Cl–, Br–, and MeO– becomes 100% regiospecific for ?-attack....

  7. Hydrate Control for Gas Storage Operations

    SciTech Connect (OSTI)

    Jeffrey Savidge

    2008-10-31T23:59:59.000Z

    The overall objective of this project was to identify low cost hydrate control options to help mitigate and solve hydrate problems that occur in moderate and high pressure natural gas storage field operations. The study includes data on a number of flow configurations, fluids and control options that are common in natural gas storage field flow lines. The final phase of this work brings together data and experience from the hydrate flow test facility and multiple field and operator sources. It includes a compilation of basic information on operating conditions as well as candidate field separation options. Lastly the work is integrated with the work with the initial work to provide a comprehensive view of gas storage field hydrate control for field operations and storage field personnel.

  8. Weakening of ice by magnesium perchlorate hydrate

    E-Print Network [OSTI]

    Lenferink, Hendrik J., 1985-

    2012-01-01T23:59:59.000Z

    I show that perchlorate hydrates, which have been indirectly detected at high Martian circumpolar latitudes by the Phoenix Mars Lander, have a dramatic effect upon the rheological behavior of polycrystalline water ice under ...

  9. Modeling of gas hydrates from first principles

    E-Print Network [OSTI]

    Cao, Zhitao, 1974-

    2002-01-01T23:59:59.000Z

    Ab initio calculations were used to determine the H20-CH4 potential energy surface (PES) accurately for use in modeling gas hydrates. Electron correlation was found to be treated accurately by the second-order Moller-Plesset ...

  10. Thermal dissociation behavior and dissociation enthalpies of methane-carbon dioxide mixed hydrates

    E-Print Network [OSTI]

    Kwon, T.H.

    2012-01-01T23:59:59.000Z

    Dissociation heat of mixed-gas hydrate composed of methaneInternational Conference on Gas Hydrates (ICGH 2008), 2008,and specific heats of gas hydrates under submarine and

  11. Physical property changes in hydrate-bearing sediment due to depressurization and subsequent repressurization

    E-Print Network [OSTI]

    Waite, W.F.

    2008-01-01T23:59:59.000Z

    distribution of water, gas and hydrate within a core and thecontaining natural and laboratory-formed gas hydrate, inNatural Gas Hydrate In Oceanic and Permafrost Environments,

  12. Methane Hydrate Dissociation by Depressurization in a Mount Elbert Sandstone Sample: Experimental Observations and Numerical Simulations

    E-Print Network [OSTI]

    Kneafsey, T.

    2012-01-01T23:59:59.000Z

    DOE-USGS Mount Elbert gas hydrate stratigraphic test well:International Conference on Gas Hydrates, Vancouver, BritishGeologic controls on gas hydrate occurrence in the Mount

  13. The dynamic response of oceanic hydrate deposits to ocean temperature change

    E-Print Network [OSTI]

    Reagan, Matthew T.

    2008-01-01T23:59:59.000Z

    of the fate of gas hydrates during transit through the oceanVA. (1998), Submarine Gas Hydrates. St. Petersburg. Gornitzgas reservoirs below gas-hydrate provinces, Nature, 427,

  14. RESOURCE CHARACTERIZATION AND QUANTIFICATION OF NATURAL GAS-HYDRATE AND ASSOCIATED FREE-GAS ACCUMULATIONS IN THE PRUDHOE BAY - KUPARUK RIVER AREA ON THE NORTH SLOPE OF ALASKA

    SciTech Connect (OSTI)

    Robert Hunter; Shirish Patil; Robert Casavant; Tim Collett

    2003-06-02T23:59:59.000Z

    Interim results are presented from the project designed to characterize, quantify, and determine the commercial feasibility of Alaska North Slope (ANS) gas-hydrate and associated free-gas resources in the Prudhoe Bay Unit (PBU), Kuparuk River Unit (KRU), and Milne Point Unit (MPU) areas. This collaborative research will provide practical input to reservoir and economic models, determine the technical feasibility of gas hydrate production, and influence future exploration and field extension of this potential ANS resource. The large magnitude of unconventional in-place gas (40-100 TCF) and conventional ANS gas commercialization evaluation creates industry-DOE alignment to assess this potential resource. This region uniquely combines known gas hydrate presence and existing production infrastructure. Many technical, economical, environmental, and safety issues require resolution before enabling gas hydrate commercial production. Gas hydrate energy resource potential has been studied for nearly three decades. However, this knowledge has not been applied to practical ANS gas hydrate resource development. ANS gas hydrate and associated free gas reservoirs are being studied to determine reservoir extent, stratigraphy, structure, continuity, quality, variability, and geophysical and petrophysical property distribution. Phase 1 will characterize reservoirs, lead to recoverable reserve and commercial potential estimates, and define procedures for gas hydrate drilling, data acquisition, completion, and production. Phases 2 and 3 will integrate well, core, log, and long-term production test data from additional wells, if justified by results from prior phases. The project could lead to future ANS gas hydrate pilot development. This project will help solve technical and economic issues to enable government and industry to make informed decisions regarding future commercialization of unconventional gas-hydrate resources.

  15. CARBON DIOXIDE HYDRATES CRYSTALLISATION IN EMULSION Aurlie Galfr, Amara Fezoua, Yamina Ouabbas, Ana Cameirao, Jean Michel Herri

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    identified as major sources responsible for global warming. To reduce carbon dioxide emissions, capture (several cubic meters per second of CO2), the capture technology needs to run at severe conditions and to minimize the cost of the process Innovative technology capture by gas hydrates crystallization can

  16. Fe-containing phases in hydrated cements

    SciTech Connect (OSTI)

    Dilnesa, B.Z., E-mail: belay.dilnesa@gmail.com [Empa, Laboratory for Concrete and Construction Chemistry, Überlandstrasse 129, 8600 Dübendorf (Switzerland); Wieland, E. [Paul Scherrer Institute, Laboratory for Waste Management, 5232 Villigen PSI (Switzerland); Lothenbach, B. [Empa, Laboratory for Concrete and Construction Chemistry, Überlandstrasse 129, 8600 Dübendorf (Switzerland); Dähn, R. [Paul Scherrer Institute, Laboratory for Waste Management, 5232 Villigen PSI (Switzerland); Scrivener, K.L. [Ecole Polytechnique Federal de Lausanne (EPFL), Laboratory for Construction Materials, 1015 Lausanne (Switzerland)

    2014-04-01T23:59:59.000Z

    In this study synchrotron X-ray absorption spectroscopy (XAS) has been applied, an element specific technique which allows Fe-containing phases to be identified in the complex mineral mixture of hydrated cements. Several Fe species contributed to the overall Fe K-edge spectra recorded on the cement samples. In the early stage of cement hydration ferrite was the dominant Fe-containing mineral. Ferrihydrite was detected during the first hours of the hydration process. After 1 day the formation of Al- and Fe-siliceous hydrogarnet was observed, while the amount of ferrihydrite decreased. The latter finding agrees with thermodynamic modeling, which predicts the formation of Fe-siliceous hydrogarnet in Portland cement systems. The presence of Al- and Fe-containing siliceous hydrogarnet was further substantiated in the residue of hydrated cement by performing a selective dissolution procedure. - Highlights: • Fe bound to ferrihydrite at early age hydration • Fe found to be stable in siliceous hydrogarnet at longer term age hydration • Fe-containing AFt and AFm phases are less stable than siliceous hydrogarnet. • The study demonstrates EXAFS used to identify amorphous or poorly crystalline phases.

  17. Automobiles on Steroids: Product Attribute Trade-Offs and Technological Progress in the Automobile Sector

    E-Print Network [OSTI]

    Knittel, Christopher R

    2009-01-01T23:59:59.000Z

    engine power/weight technology costs is correlated withto Vehicle-Speci?c Technology Costs I estimate threefor Proxies of Technology Costs Base Cobb-Douglas Model

  18. Technology and social process : oscillations in Iron Age copper production and power in Southern Jordan

    E-Print Network [OSTI]

    Ben-Yosef, Erez

    2010-01-01T23:59:59.000Z

    Yosef, E. , 2008. Technology and Society: Some Insights onYosef, E. , 2008a. Technology and Society: Some Insights onweb’) between technology and society (Chapter 1) and the

  19. UWM-CBU Concrete Materials Technology Series Program No. 71 Workshop on GREEN CONSTRUCTION MATERIALS USING COAL-COMBUSTION PRODUCTS

    E-Print Network [OSTI]

    Saldin, Dilano

    : Classification (Class F, Class C, Class N, and SDA & Clean-Coal Ash); Chemical Composition; PhysicalUWM-CBU Concrete Materials Technology Series Program No. 71 Workshop on GREEN CONSTRUCTION MATERIALS USING COAL-COMBUSTION PRODUCTS Center for By-Products Utilization NONPROFIT ORGANIZATION 3200

  20. Anomalous porosity preservation and preferential accumulation of gas hydrate in the Andaman accretionary wedge, NGHP-01 site 17A

    SciTech Connect (OSTI)

    Rose, Kelly K.; Johnson, Joel E.; Torres, Marta E.; Hong, WeiLi; Giosan, Liviu; Solomon, E.; Kastner, Miriam; Cawthern, Thomas; Long, Philip E.; Schaef, Herbert T.

    2014-12-01T23:59:59.000Z

    In addition to well established properties that control the presence or absence of the hydrate stability zone, such as pressure, temperature, and salinity, additional parameters appear to influence the concentration of gas hydrate in host sediments. The stratigraphic record at Site 17A in the Andaman Sea, eastern Indian Ocean, illustrates the need to better understand the role pore-scale phenomena play in the distribution and presence of marine gas hydrates in a variety of subsurface settings. In this paper we integrate field-generated datasets with newly acquired sedimentology, physical property, imaging and geochemical data with mineral saturation and ion activity products of key mineral phases such as amorphous silica and calcite, to document the presence and nature of secondary precipitates that contributed to anomalous porosity preservation at Site 17A in the Andaman Sea. This study demonstrates the importance of grain-scale subsurface heterogeneities in controlling the occurrence and distribution of concentrated gas hydrate accumulations in marine sediments, and document the importance that increased permeability and enhanced porosity play in supporting gas concentrations sufficient to support gas hydrate formation. The grain scale relationships between porosity, permeability, and gas hydrate saturation documented at Site 17A likely offer insights into what may control the occurrence and distribution of gas hydrate in other sedimentary settings.

  1. Novel Fast Pyrolysis/Catalytic Technology for the Production of Stable Upgraded Liquids

    SciTech Connect (OSTI)

    Ted Oyama, Foster Agblevor, Francine Battaglia, Michael Klein

    2013-01-18T23:59:59.000Z

    The objective of the proposed research is the demonstration and development of a novel biomass pyrolysis technology for the production of a stable bio-oil. The approach is to carry out catalytic hydrodeoxygenation (HDO) and upgrading together with pyrolysis in a single fluidized bed reactor with a unique two-level design that permits the physical separation of the two processes. The hydrogen required for the HDO will be generated in the catalytic section by the water-gas shift reaction employing recycled CO produced from the pyrolysis reaction itself. Thus, the use of a reactive recycle stream is another innovation in this technology. The catalysts will be designed in collaboration with BASF Catalysts LLC (formerly Engelhard Corporation), a leader in the manufacture of attrition-resistant cracking catalysts. The proposed work will include reactor modeling with state-of-the-art computational fluid dynamics in a supercomputer, and advanced kinetic analysis for optimization of bio-oil production. The stability of the bio-oil will be determined by viscosity, oxygen content, and acidity determinations in real and accelerated measurements. A multi-faceted team has been assembled to handle laboratory demonstration studies and computational analysis for optimization and scaleup.

  2. Study of the Natural Gas Hydrate 'Trap Zone' and the Methane Hydrate Potential in the Sverdrup Basin, Canada

    SciTech Connect (OSTI)

    Majorowicz, J. A. [Northern Geothermal Consult. (Canada)], E-mail: majorowi@show.ca; Hannigan, P. K.; Osadetz, K. G. [Geological Survey of Canada, Calgary (Canada)

    2002-06-15T23:59:59.000Z

    The methane hydrate stability zone beneath Sverdrup Basin has developed to a depth of 2 km underneath the Canadian Arctic Islands and 1 km below sea level under the deepest part of the inter-island sea channels. It is not, however, a continuous zone. Methane hydrates are detected in this zone, but the gas hydrate/free gas contact occurs rarely. Interpretation of well logs indicate that methane hydrate occurs within the methane stability zone in 57 of 150 analyzed wells. Fourteen wells show the methane hydrate/free gas contact. Analysis of the distribution of methane hydrate and hydrate/gas contact occurrences with respect to the present methane hydrate stability zone indicate that, in most instances, the detected methane hydrate occurs well above the base of methane hydrate stability. This relationship suggests that these methane hydrates were formed in shallower strata than expected with respect to the present hydrate stability zone from methane gases which migrated upward into hydrate trap zones. Presently, only a small proportion of gas hydrate occurrences occur in close proximity to the base of predicted methane hydrate stability. The association of the majority of detected hydrates with deeply buried hydrocarbon discoveries, mostly conventional natural gas accumulations, or mapped seismic closures, some of which are dry, located in structures in western and central Sverdrup Basin, indicate the concurring relationship of hydrate occurrence with areas of high heat flow. Either present-day or paleo-high heat flows are relevant. Twenty-three hydrate occurrences coincide directly with underlying conventional hydrocarbon accumulations. Other gas hydrate occurrences are associated with structures filled with water with evidence of precursor hydrocarbons that were lost because of upward leakage.

  3. Controls on Gas Hydrate Formation and Dissociation

    SciTech Connect (OSTI)

    Miriam Kastner; Ian MacDonald

    2006-03-03T23:59:59.000Z

    The main objectives of the project were to monitor, characterize, and quantify in situ the rates of formation and dissociation of methane hydrates at and near the seafloor in the northern Gulf of Mexico, with a focus on the Bush Hill seafloor hydrate mound; to record the linkages between physical and chemical parameters of the deposits over the course of one year, by emphasizing the response of the hydrate mound to temperature and chemical perturbations; and to document the seafloor and water column environmental impacts of hydrate formation and dissociation. For these, monitoring the dynamics of gas hydrate formation and dissociation was required. The objectives were achieved by an integrated field and laboratory scientific study, particularly by monitoring in situ formation and dissociation of the outcropping gas hydrate mound and of the associated gas-rich sediments. In addition to monitoring with the MOSQUITOs, fluid flow rates and temperature, continuously sampling in situ pore fluids for the chemistry, and imaging the hydrate mound, pore fluids from cores, peepers and gas hydrate samples from the mound were as well sampled and analyzed for chemical and isotopic compositions. In order to determine the impact of gas hydrate dissociation and/or methane venting across the seafloor on the ocean and atmosphere, the overlying seawater was sampled and thoroughly analyzed chemically and for methane C isotope ratios. At Bush hill the pore fluid chemistry varies significantly over short distances as well as within some of the specific sites monitored for 440 days, and gas venting is primarily focused. The pore fluid chemistry in the tub-warm and mussel shell fields clearly documented active gas hydrate and authigenic carbonate formation during the monitoring period. The advecting fluid is depleted in sulfate, Ca Mg, and Sr and is rich in methane; at the main vent sites the fluid is methane supersaturated, thus bubble plumes form. The subsurface hydrology exhibits both up-flow and down-flow of fluid at rates that range between 0.5 to 214 cm/yr and 2-162 cm/yr, respectively. The fluid flow system at the mound and background sites are coupled having opposite polarities that oscillate episodically between 14 days to {approx}4 months. Stability calculations suggest that despite bottom water temperature fluctuations, of up to {approx}3 C, the Bush Hill gas hydrate mound is presently stable, as also corroborated by the time-lapse video camera images that did not detect change in the gas hydrate mound. As long as methane (and other hydrocarbon) continues advecting at the observed rates the mound would remain stable. The {_}{sup 13}C-DIC data suggest that crude oil instead of methane serves as the primary electron-donor and metabolic substrate for anaerobic sulfate reduction. The oil-dominated environment at Bush Hill shields some of the methane bubbles from being oxidized both anaerobically in the sediment and aerobically in the water column. Consequently, the methane flux across the seafloor is higher at Bush hill than at non-oil rich seafloor gas hydrate regions, such as at Hydrate Ridge, Cascadia. The methane flux across the ocean/atmosphere interface is as well higher. Modeling the methane flux across this interface at three bubble plumes provides values that range from 180-2000 {_}mol/m{sup 2} day; extrapolating it over the Gulf of Mexico basin utilizing satellite data is in progress.

  4. Strength and hydration properties of reactive MgO-activated ground granulated blastfurnace slag paste

    E-Print Network [OSTI]

    Jin, Fei; Gu, Kai; Al-Tabbaa, Abir

    2014-12-10T23:59:59.000Z

    on the Siemens D5000 X-ray diffractometer using a scanning range from 5 to 60 (2?), with scanning speed of 2 s/step and resolution of 0.05 °/step to identify the hydration products formed. TGA was conducted on PerkinElmer STA6000 equipment from 40 to 1000 °C...

  5. Complex admixtures of clathrate hydrates in a water desalination method

    DOE Patents [OSTI]

    Simmons, Blake A. (San Francisco, CA); Bradshaw, Robert W. (Livermore, CA); Dedrick, Daniel E. (Berkeley, CA); Anderson, David W. (Riverbank, CA)

    2009-07-14T23:59:59.000Z

    Disclosed is a method that achieves water desalination by utilizing and optimizing clathrate hydrate phenomena. Clathrate hydrates are crystalline compounds of gas and water that desalinate water by excluding salt molecules during crystallization. Contacting a hydrate forming gaseous species with water will spontaneously form hydrates at specific temperatures and pressures through the extraction of water molecules from the bulk phase followed by crystallite nucleation. Subsequent dissociation of pure hydrates yields fresh water and, if operated correctly, allows the hydrate-forming gas to be efficiently recycled into the process stream.

  6. Energy, water and process technologies integration for the simultaneous production of

    E-Print Network [OSTI]

    Grossmann, Ignacio E.

    production process from gasification. Keywords: Bioethanol; Energy and Food Production; Integrated Process production of corn. Figure 1.- Bioethanol Production expectations (source US DOE) However, there are limits

  7. Methane Hydrate Dissociation by Depressurization in a Mount Elbert Sandstone Sample: Experimental Observations and Numerical Simulations

    SciTech Connect (OSTI)

    Kneafsey, T.; Moridis, G.J.

    2011-01-15T23:59:59.000Z

    A preserved sample of hydrate-bearing sandstone from the Mount Elbert Test Well was dissociated by depressurization while monitoring the internal temperature of the sample in two locations and the density changes at high spatial resolution using x-ray CT scanning. The sample contained two distinct regions having different porosity and grain size distributions. The hydrate dissociation occurred initially throughout the sample as a result of depressing the pressure below the stability pressure. This initial stage reduced the temperature to the equilibrium point, which was maintained above the ice point. After that, dissociation occurred from the outside in as a result of heat transfer from the controlled temperature bath surrounding the pressure vessel. Numerical modeling of the test using TOUGH+HYDRATE yielded a gas production curve that closely matches the experimentally measured curve.

  8. CO-PRODUCTION OF HYDROGEN AND ELECTRICITY USING PRESSURIZED CIRCULATING FLUIDIZED BED GASIFICATION TECHNOLOGY

    SciTech Connect (OSTI)

    Zhen Fan

    2006-05-30T23:59:59.000Z

    Foster Wheeler has completed work under a U.S. Department of Energy cooperative agreement to develop a gasification equipment module that can serve as a building block for a variety of advanced, coal-fueled plants. When linked with other equipment blocks also under development, studies have shown that Foster Wheeler's gasification module can enable an electric generating plant to operate with an efficiency exceeding 60 percent (coal higher heating value basis) while producing near zero emissions of traditional stack gas pollutants. The heart of the equipment module is a pressurized circulating fluidized bed (PCFB) that is used to gasify the coal; it can operate with either air or oxygen and produces a coal-derived syngas without the formation of corrosive slag or sticky ash that can reduce plant availabilities. Rather than fuel a gas turbine for combined cycle power generation, the syngas can alternatively be processed to produce clean fuels and or chemicals. As a result, the study described herein was conducted to determine the performance and economics of using the syngas to produce hydrogen for sale to a nearby refinery in a hydrogen-electricity co-production plant setting. The plant is fueled with Pittsburgh No. 8 coal, produces 99.95 percent pure hydrogen at a rate of 260 tons per day and generates 255 MWe of power for sale. Based on an electricity sell price of $45/MWhr, the hydrogen has a 10-year levelized production cost of $6.75 per million Btu; this price is competitive with hydrogen produced by steam methane reforming at a natural gas price of $4/MMBtu. Hence, coal-fueled, PCFB gasifier-based plants appear to be a viable means for either high efficiency power generation or co-production of hydrogen and electricity. This report describes the PCFB gasifier-based plant, presents its performance and economics, and compares it to other coal-based and natural gas based hydrogen production technologies.

  9. Characterization of NOx Species in Dehydrated and Hydrated Na...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    NOx Species in Dehydrated and Hydrated Na- and Ba-Y, FAU Zeolites Formed in NO Adsorption. Characterization of NOx Species in Dehydrated and Hydrated Na- and Ba-Y, FAU Zeolites...

  10. Technical support for the Ohio Coal Technology Program. Volume 1, Baseline of knowledge concerning by-product characteristics: Final report

    SciTech Connect (OSTI)

    Olfenbuttel, R.; Clark, S.; Helper, E.; Hinchee, R.; Kuntz, C.; Means, J.; Oxley, J.; Paisley, M.; Rogers, C.; Sheppard, W.; Smolak, L. [Battelle, Columbus, OH (United States)

    1989-08-28T23:59:59.000Z

    This report was prepared for the Ohio Coal Development Office (OCDO) under Grant Agreement No. CDO/R-88-LRl and comprises two volumes. Volume I presents data on the chemical, physical, and leaching characteristics of by-products from a wide variety of clean coal combustion processes. Volume II consists of a discussion of (a) process modification waste minimization opportunities and stabilization considerations; (b) research and development needs and issues relating to clean coal combustion technologies and by-products; (c) the market potential for reusing or recycling by-product materials; and (d) regulatory considerations relating to by-product disposal or reuse.

  11. Fuel cell membrane hydration and fluid metering

    DOE Patents [OSTI]

    Jones, Daniel O. (Glenville, NY); Walsh, Michael M. (Fairfield, CT)

    2003-01-01T23:59:59.000Z

    A hydration system includes fuel cell fluid flow plate(s) and injection port(s). Each plate has flow channel(s) with respective inlet(s) for receiving respective portion(s) of a given stream of reactant fluid for a fuel cell. Each injection port injects a portion of liquid water directly into its respective flow channel. This serves to hydrate at least corresponding part(s) of a given membrane of the corresponding fuel cell(s). The hydration system may be augmented by a metering system including flow regulator(s). Each flow regulator meters an injecting at inlet(s) of each plate of respective portions of liquid into respective portion(s) of a given stream of fluid by corresponding injection port(s).

  12. Fuel cell membrane hydration and fluid metering

    DOE Patents [OSTI]

    Jones, Daniel O. (Glenville, NY); Walsh, Michael M. (Fairfield, CT)

    1999-01-01T23:59:59.000Z

    A hydration system includes fuel cell fluid flow plate(s) and injection port(s). Each plate has flow channel(s) with respective inlet(s) for receiving respective portion(s) of a given stream of reactant fluid for a fuel cell. Each injection port injects a portion of liquid water directly into its respective flow channel in order to mix its respective portion of liquid water with the corresponding portion of the stream. This serves to hydrate at least corresponding part(s) of a given membrane of the corresponding fuel cell(s). The hydration system may be augmented by a metering system including flow regulator(s). Each flow regulator meters an injecting at inlet(s) of each plate of respective portions of liquid into respective portion(s) of a given stream of fluid by corresponding injection port(s).

  13. Curvature Dependence of Hydrophobic Hydration Dynamics

    E-Print Network [OSTI]

    R. Gregor Weiß; Matthias Heyden; Joachim Dzubiella

    2015-04-08T23:59:59.000Z

    We investigate the curvature-dependence of water dynamics in the vicinity of hydrophobic spherical solutes using molecular dynamics simulations. For both, the lateral and perpendicular diffusivity as well as for H-bond kinetics of water in the first hydration shell, we find a non-monotonic solute-size dependence, exhibiting extrema close to the well-known structural crossover length scale for hydrophobic hydration. Additionally, we find an apparently anomalous diffusion for water moving parallel to the surface of small solutes, which, however, can be explained by topology effects. The intimate connection between solute curvature, water structure and dynamics has implications for our understanding of hydration dynamics at heterogeneous biomolecular surfaces.

  14. Emerging Energy-efficiency and CO2 Emission-reduction Technologies for Cement and Concrete Production

    E-Print Network [OSTI]

    Hasanbeigi, Ali

    2013-01-01T23:59:59.000Z

    24 3.5. Emerging Carbon Capture Technologies for the CementGmbH (ECRA), 2007. Carbon Capture Technology - Options andEmerging carbon capture technologies for the cement industry

  15. Investigating late stage biopharmaceutical product loss using novel analytical and process technology

    E-Print Network [OSTI]

    Hunnicutt, Leigh Anne

    2008-01-01T23:59:59.000Z

    The biopharmaceutical industry uses recombinant protein technologies to provide novel therapeutics to patients around the world. These technologies have presented exciting opportunities for breakthrough medical treatments ...

  16. Essays on regional and firm-level productivity, military spending, and technology

    E-Print Network [OSTI]

    Goudie, Bryan Daniel

    2008-01-01T23:59:59.000Z

    BLDG & REPAIRING GENERAL ELECTRIC CO CONGLOMERATES GENERALUnited Technologies General Electric TRW Inc Honeywell Inc-United Technologies General Electric TRW Inc Honeywell Inc-

  17. The thermodynamic properties of hydrated -Al2O3 nanoparticles

    SciTech Connect (OSTI)

    Spencer, Elinor [Virginia Polytechnic Institute and State University] [Virginia Polytechnic Institute and State University; Huang, Baiyu [Brigham Young University, Provo] [Brigham Young University, Provo; Parker, Stewart F. [ISIS Facility, Rutherford Appleton Laboratory (ISIS)] [ISIS Facility, Rutherford Appleton Laboratory (ISIS); Kolesnikov, Alexander I [ORNL] [ORNL; Ross, Dr. Nancy [Virginia Polytechnic Institute and State University] [Virginia Polytechnic Institute and State University; Woodfield, Brian [Brigham Young University, Provo] [Brigham Young University, Provo

    2013-01-01T23:59:59.000Z

    In this paper we report a combined calorimetric and inelastic neutron scattering (INS) study of hydrated -Al2O3 ( -alumina) nanoparticles. These complementary techniques have enabled a comprehensive evaluation of the thermodynamic properties of this technological and industrially important metal oxide to be achieved. The isobaric heat capacity (Cp) data presented herein provide further critical insights into the much-debated chemical composition of -alumina nanoparticles. Furthermore, the isochoric heat capacity (Cv) of the surface water, which is so essential to the stability of all metal-oxides at the nanoscale, has been extracted from the high-resolution INS data and differs significantly from that of ice Ih due to the dominating influence of strong surface-water interactions. This study also encompassed the analysis of four -alumina samples with differing pore diameters [4.5 (1), 13.8 (2), 17.9 (3), and 27.2 nm (4)], and the results obtained allow us to unambiguously conclude that the water content and pore size have no influence on the thermodynamic behaviour of hydrated -alumina nanoparticles.

  18. Confined water in the low hydration regime

    E-Print Network [OSTI]

    P. Gallo; M. Rapinesi; M. Rovere

    2002-04-05T23:59:59.000Z

    Molecular dynamics results on water confined in a silica pore in the low hydration regime are presented. Strong layering effects are found due to the hydrophilic character of the substrate. The local properties of water are studied as function of both temperature and hydration level. The interaction of the thin films of water with the silica atoms induces a strong distortion of the hydrogen bond network. The residence time of the water molecules is dependent on the distance from the surface. Its behavior shows a transition from a brownian to a non-brownian regime approaching the substrate in agreement with results found in studies of water at contact with globular proteins.

  19. Dehydration of plutonium or neptunium trichloride hydrate

    DOE Patents [OSTI]

    Foropoulos, J. Jr.; Avens, L.R.; Trujillo, E.A.

    1992-03-24T23:59:59.000Z

    A process is described for preparing anhydrous actinide metal trichlorides of plutonium or neptunium by reacting an aqueous solution of an actinide metal trichloride selected from the group consisting of plutonium trichloride or neptunium trichloride with a reducing agent capable of converting the actinide metal from an oxidation state of +4 to +3 in a resultant solution, evaporating essentially all the solvent from the resultant solution to yield an actinide trichloride hydrate material, dehydrating the actinide trichloride hydrate material by heating the material in admixture with excess thionyl chloride, and recovering anhydrous actinide trichloride.

  20. Dehydration of plutonium or neptunium trichloride hydrate

    DOE Patents [OSTI]

    Foropoulos, Jr., Jerry (Los Alamos, NM); Avens, Larry R. (Los Alamos, NM); Trujillo, Eddie A. (Espanola, NM)

    1992-01-01T23:59:59.000Z

    A process of preparing anhydrous actinide metal trichlorides of plutonium or neptunium by reacting an aqueous solution of an actinide metal trichloride selected from the group consisting of plutonium trichloride or neptunium trichloride with a reducing agent capable of converting the actinide metal from an oxidation state of +4 to +3 in a resultant solution, evaporating essentially all the solvent from the resultant solution to yield an actinide trichloride hydrate material, dehydrating the actinide trichloride hydrate material by heating the material in admixture with excess thionyl chloride, and recovering anhydrous actinide trichloride is provided.

  1. Gas hydrates in the Gulf of Mexico

    E-Print Network [OSTI]

    Cox, Henry Benjamin

    1986-01-01T23:59:59.000Z

    GAS HYDRATES IN THE GULF OF MEXICO A Thesis by HENRY BENJAMIN COX Submitted to the Graduate College of Texas A&M University in partial fulfillment of the requirements for the degree of MASTER OF SCIENCE December 1986 Major Subject...: Oceanography GAS HYDRATES IN THE GULF OF MEXICO A Thesis by HENRY BENJAMIN COX Approved as to style and content by: James M. Brooks (Chair of Committee) Leis M. Jef e (Member) Andre M. Landry, J (Member) Roger R. Fay (Member) Robert 0. Reid (Head...

  2. Dynamic behavior of hydration water in calcium-silicate-hydrate gel: A quasielastic neutron scattering spectroscopy investigation

    E-Print Network [OSTI]

    Li, Hua

    The translational dynamics of hydration water confined in calcium-silicate-hydrate (C-S-H) gel was studied by quasielastic neutron scattering spectroscopy in the temperature range from 280 to 230 K. The stretch exponent ...

  3. MODELING OF HYDRATION KINETICS AND SHRINKAGE OF PORTLAND CEMENT PASTE

    E-Print Network [OSTI]

    Meyer, Christian

    MODELING OF HYDRATION KINETICS AND SHRINKAGE OF PORTLAND CEMENT PASTE Feng Lin Submitted in partial and Sciences COLUMBIA UNIVERSITY 2006 #12;MODELING OF HYDRATION KINETICS AND SHRINKAGE OF PORTLAND CEMENT PASTE;ABSTRACT MODELING OF HYDRATION KINETICS AND SHRINKAGE OF PORTLAND CEMENT PASTE Feng Lin A mathematical

  4. Videos of Experiments from ORNL Gas Hydrate Research

    DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

    Gas hydrate research performed by the Environmental Sciences Division utilizes the ORNL Seafloor Process Simulator, the Parr Vessel, the Sapphire Cell, a fiber optic distributed sensing system, and Raman spectroscopy. The group studies carbon sequestration in the ocean, desalination, gas hydrates in the solar system, and nucleation and dissociation kinetics. The videos available at the gas hydrates website are very short clips from experiments.

  5. Rock-physics Models for Gas-hydrate Systems Associated

    E-Print Network [OSTI]

    Texas at Austin, University of

    Rock-physics Models for Gas-hydrate Systems Associated with Unconsolidated Marine Sediments Diana at Austin, Austin, Texas, U.S.A. ABSTRACT R ock-physics models are presented describing gas-hydrate systems associated with unconsolidated marine sediments. The goals are to predict gas-hydrate concentration from

  6. The goal of this work is to quantify the Van der Waals interactions in systems involving gas hydrates. Gas hydrates are crystalline com-

    E-Print Network [OSTI]

    Boyer, Edmond

    gas hydrates. Gas hydrates are crystalline com- pounds that are often encountered in oil and gas briefly present the hydrate crystalline structure and the role of hydrates in oil-and gas industry the industrial contexts where they appear, we shall cite : hydrate plugs obstructing oil- or gas

  7. Efficient capture of CO{sub 2} from simulated flue gas by formation of TBAB or TBAF semiclathrate hydrates

    SciTech Connect (OSTI)

    Shuanshi Fan; Shifeng Li; Jingqu Wang; Xuemei Lang; Yanhong Wang [South China University of Technology, Guangzhou (China). Key Laboratory of Enhanced Heat Transfer and Energy Conversation

    2009-08-15T23:59:59.000Z

    Capturing CO{sub 2} by forming hydrate is an attractive technology for reducing the greenhouse effect. The most primary challenges are high energy consumption, low hydrate formation rate, and separation efficiency. This work presents efficient capture of CO{sub 2} from simulated flue gas (CO{sub 2} (16.60 mol %)/N{sub 2} binary mixtures) by formation of semiclathrate hydrates at 4.5 and 7.1{sup o}C and feed pressures ranging from 2.19 to 7.31 MPa. The effect of 0.293 mol % tetra-n-butyl ammonium bromide (TBAB) and tetra-n-butyl ammonium fluoride (TBAF) on the hydrate formation rate, reactor space velocity, and CO{sub 2} separation efficiency was studied in a 1 L stirred reactor. The results showed the hydrate formation rate constant increased with increasing feed pressure and reached the maximum at 2.82 x 10{sup -7} mol{sup 2}/(s.J) with TBAB and 8.26 x 10{sup -7} mol{sup 2}/(s.J) with TBAF. The space velocity of the hydrate reactor increased with increasing feed pressure and reached a maximum of 13.46 h{sup -1} with TBAB and 25.96 h{sup -1} with TBAF. CO{sub 2} recovery was about 50%, and the optimum CO{sub 2} separation factor with TBAF was 36.98, which was about 4 times higher than that with TBAB in the range of feed pressure. CO{sub 2} could be enriched to 90.40 mol % from simulated flue gas under low feed pressure by two stages of hydrate separation with TBAF. The results demonstrated that TBAB, especially TBAF, could accelerate hydrate formation. The space velocity of the hydrate reactor with TBAB or TBAF was higher than that with THF. CO{sub 2} could be easily enriched in the hydrate phase by two stages of hydrate separation under gentle conditions. 27 refs., 8 figs., 5 tabs.

  8. Technology

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of ScienceandMesa del SolStrengthening a solidSynthesis of 2D AlloysTrails NewsTechnologyTechnology A

  9. Technology

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of ScienceandMesa del SolStrengthening a solidSynthesis of 2D AlloysTrails NewsTechnologyTechnology

  10. Emerging Energy-efficiency and CO2 Emission-reduction Technologies for Cement and Concrete Production

    E-Print Network [OSTI]

    Hasanbeigi, Ali

    2013-01-01T23:59:59.000Z

    technology would be more economical in new plants because retrofits would involve removal of existing

  11. Development of an In Situ Biosurfactant Production Technology for Enhanced Oil Recovery

    SciTech Connect (OSTI)

    M.J. McInerney; R.M. Knapp; Kathleen Duncan; D.R. Simpson; N. Youssef; N. Ravi; M.J. Folmsbee; T.Fincher; S. Maudgalya; Jim Davis; Sandra Weiland

    2007-09-30T23:59:59.000Z

    The long-term economic potential for enhanced oil recovery (EOR) is large with more than 300 billion barrels of oil remaining in domestic reservoirs after conventional technologies reach their economic limit. Actual EOR production in the United States has never been very large, less than 10% of the total U. S. production even though a number of economic incentives have been used to stimulate the development and application of EOR processes. The U.S. DOE Reservoir Data Base contains more than 600 reservoirs with over 12 billion barrels of unrecoverable oil that are potential targets for microbially enhanced oil recovery (MEOR). If MEOR could be successfully applied to reduce the residual oil saturation by 10% in a quarter of these reservoirs, more than 300 million barrels of oil could be added to the U.S. oil reserve. This would stimulate oil production from domestic reservoirs and reduce our nation's dependence on foreign imports. Laboratory studies have shown that detergent-like molecules called biosurfactants, which are produced by microorganisms, are very effective in mobilizing entrapped oil from model test systems. The biosurfactants are effective at very low concentrations. Given the promising laboratory results, it is important to determine the efficacy of using biosurfactants in actual field applications. The goal of this project is to move biosurfactant-mediated oil recovery from laboratory investigations to actual field applications. In order to meet this goal, several important questions must be answered. First, it is critical to know whether biosurfactant-producing microbes are present in oil formations. If they are present, then it will be important to know whether a nutrient regime can be devised to stimulate their growth and activity in the reservoir. If biosurfactant producers are not present, then a suitable strain must be obtained that can be injected into oil reservoirs. We were successful in answering all three questions. The specific objectives of the project were (1) to determine the prevalence of biosurfactant producers in oil reservoirs, and (2) to develop a nutrient regime that would stimulate biosurfactant production in the oil reservoir.

  12. Multipole Electrostatics in Hydration Free Energy Calculations

    E-Print Network [OSTI]

    Ponder, Jay

    Multipole Electrostatics in Hydration Free Energy Calculations YUE SHI,1 CHUANJIE WU,2 JAY W Acceptance Ratio method. We have compared two approaches to derive the atomic multipoles from quantum mechanical calculations: one directly from the new distributed multipole analysis and the other involving

  13. Dynamics of Kr in dense clathrate hydrates.

    SciTech Connect (OSTI)

    Klug, D. D.; Tse, J. S.; Zhao, J. Y.; Sturhahn, W.; Alp, E. E.; Tulk, C. A. (X-Ray Science Division); (National Research Council of Canada); (Univ. of Saskatchewan); (ORNL)

    2011-01-01T23:59:59.000Z

    The dynamics of Kr atoms as guests in dense clathrate hydrate structures are investigated using site specific {sup 83}Kr nuclear resonant inelastic x-ray scattering (NRIXS) spectroscopy in combination with molecular dynamics simulations. The dense structure H hydrate and filled-ice structures are studied at high pressures in a diamond anvil high-pressure cell. The dynamics of Kr in the structure H clathrate hydrate quench recovered at 77 K is also investigated. The Kr phonon density of states obtained from the experimental NRIXS data are compared with molecular dynamics simulations. The temperature and pressure dependence of the phonon spectra provide details of the Kr dynamics in the clathrate hydrate cages. Comparison with the dynamics of Kr atoms in the low-pressure structure II obtained previously was made. The Lamb-Mossbauer factor obtained from NRIXS experiments and molecular dynamics calculations are in excellent agreement and are shown to yield unique information on the strength and temperature dependence of guest-host interactions.

  14. Enabling technologies: Supporting the development and use of innovative, energy-efficient, and environmentally friendly products and processes

    SciTech Connect (OSTI)

    NONE

    1999-02-01T23:59:59.000Z

    This pamphlet describes the Office of Industrial Technologies cooperative efforts to address industry needs for advanced materials, sensors and controls, process energy and energy efficiency. US industry needs enabling materials that are stronger and lighter, with resistance to high-temperature fatigue and improved resistance to corrosion and wear. New industrial materials such as intermetallic alloys and advanced ceramics have the potential to meet the challenges of the Industries of the Future. The manufacturing industries obtain over 85% of their energy from the on-site combustion of fuels. Enhancements to burners, boilers, and process heating systems can lower energy costs, reduce emissions, enhance fuel options, and increase safety and reliability. Robust, integrated measurement devices linked to intelligent control systems will enable US industry to use resources more efficiently and improve product quality. Through constant process monitoring and adjustment of parameters, these systems can reduce energy use and labor, minimize waste and pollution, and boost productivity. The Enabling Technologies Program is designed to address the cross-cutting needs of the Office of Industrial Technologies (OIT). OIT partners with industry to promote the development and use of energy-efficient, pollution-preventing technologies. The Nation`s environment benefits from greater use of these technologies, and industries benefit from cost savings, improved productivity, and increased competitiveness.

  15. ENDF/B-VII.1 Nuclear Data for Science and Technology: Cross Sections, Covariances, Fission Product Yields and Decay Data

    E-Print Network [OSTI]

    Danon, Yaron

    ENDF/B-VII.1 Nuclear Data for Science and Technology: Cross Sections, Covariances, Fission Product Jozef Stefan Institute, Jamova 39, 1000 Ljubljana, Slovenia 11 Nuclear Research and Consultancy Group, P 2011) The ENDF/B-VII.1 library is our latest recommended evaluated nuclear data file for use in nuclear

  16. lame synthesis is one of the most versatile and promising technologies for large-scale production of nanoscale

    E-Print Network [OSTI]

    Beaucage, Gregory

    andenvironmental24 concern. Inorganic, nanostructured materials can be produced by doping a flame with inorganicLETTERS F lame synthesis is one of the most versatile and promising technologies for large-scale production of nanoscale materials1­3 . Pyrolysis has recently been shown to be a useful route

  17. Z .Surface and Coatings Technology 130 2000 164 172 Production of high-density Ni-bonded tungsten carbide

    E-Print Network [OSTI]

    Ghoniem, Nasr M.

    Z .Surface and Coatings Technology 130 2000 164 172 Production of high-density Ni-bonded tungsten spraying; Nickel; Tungsten carbide 1. Introduction 1.1. General Since the mid-1990s, the market share of cemented Z .carbides has surpassed that of high-speed steels HSS , Z .with tungsten carbide WC having 50

  18. TOUGH+Hydrate v1.0 User's Manual: A Code for the Simulation of System Behavior in Hydrate-Bearing Geologic Media

    E-Print Network [OSTI]

    Moridis, George

    2008-01-01T23:59:59.000Z

    coexistence of aqueous, gas and hydrate phases in a cell (a deposit in which water, gas and hydrate are initially atequilibrium. The initial gas and hydrate saturations are S G

  19. TREATMENT OF METAL-LADEN HAZARDOUS WASTES WITH ADVANCED CLEAN COAL TECHNOLOGY BY-PRODUCTS

    SciTech Connect (OSTI)

    James T. Cobb, Jr.

    2003-09-12T23:59:59.000Z

    Metal-laden wastes can be stabilized and solidified using advanced clean coal technology by-products (CCTBs)--fluid bed combustor ash and spray drier solids. These utility-generated treatment chemicals are available for purchase through brokers, and commercial applications of this process are being practiced by treaters of metal-laden hazardous waste. A complex of regulations governs this industry, and sensitivities to this complex has discouraged public documentation of treatment of metal-laden hazardous wastes with CCTBs. This report provides a comprehensive public documentation of laboratory studies that show the efficacy of the stabilization and solidification of metal-laden hazardous wastes--such as lead-contaminated soils and sandblast residues--through treatment with CCTBs. It then describes the extensive efforts that were made to obtain the permits allowing a commercial hazardous waste treater to utilize CCTBs as treatment chemicals and to install the equipment required to do so. It concludes with the effect of this lengthy process on the ability of the treatment company to realize the practical, physical outcome of this effort, leading to premature termination of the project.

  20. Emerging Energy-efficiency and CO2 Emission-reduction Technologies for Cement and Concrete Production

    E-Print Network [OSTI]

    Hasanbeigi, Ali

    2013-01-01T23:59:59.000Z

    24 3.5. Emerging Carbon Capture Technologies for the Cement27 3.5.2. Post-combustion Carbon Capture Using AbsorptionGmbH (ECRA), 2007. Carbon Capture Technology - Options and

  1. Maintaining a Technology-Neutral Approach to Hydrogen Production Process Development through Conceptual Design of the Next Generation Nuclear Plant

    SciTech Connect (OSTI)

    Michael W. Patterson

    2008-05-01T23:59:59.000Z

    The Next Generation Nuclear Plant (NGNP) project was authorized in the Energy Policy Act of 2005 (EPAct), tasking the U.S. Department of Energy (DOE) with demonstrating High Temperature Gas-Cooled Reactor (HTGR) technology. The demonstration is to include the technical, licensing, operational, and commercial viability of HTGR technology for the production of electricity and hydrogen. The Nuclear Hydrogen Initiative (NHI), a component of the DOE Hydrogen Program managed by the Office of Nuclear Energy, is also investigating multiple approaches to cost effective hydrogen production from nuclear energy. The objective of NHI is development of the technology and information basis for a future decision on commercial viability. The initiatives are clearly intertwined. While the objectives of NGNP and NHI are generally consistent, NGNP has progressed to the project definition phase and the project plan has matured. Multiple process applications for the NGNP require process heat, electricity and hydrogen in varied combinations and sizes. Coupling these processes to the reactor in multiple configurations adds complexity to the design, licensing and demonstration of both the reactor and the hydrogen production process. Commercial viability of hydrogen production may depend on the specific application and heat transport configuration. A component test facility (CTF) is planned by the NGNP to support testing and demonstration of NGNP systems, including those for hydrogen production, in multiple configurations. Engineering-scale demonstrations in the CTF are expected to start in 2012 to support scheduled design and licensing activities leading to subsequent construction and operation. Engineering-scale demonstrations planned by NHI are expected to start at least two years later. Reconciliation of these schedules is recommended to successfully complete both initiatives. Hence, closer and earlier integration of hydrogen process development and heat transport systems is sensible. For integration purposes, an analysis comparing the design, cost and schedule impact of maintaining a technology neutral approach through conceptual design or making an early hydrogen process technology selection was performed. Early selection does not specifically eliminate a technology, but rather selects the first hydrogen technology for demonstration. A systems-engineering approach was taken to define decision-making criteria for selecting a hydrogen technology. The relative technical, cost and schedule risks of each approach were analyzed and risk mitigation strategies were recommended, including provisions to maintain close collaboration with the NHI. The results of these analyses are presented here.

  2. The Role of Emerging Energy-Efficient Technology in Promoting Workplace Productivity and Health: Final Report

    E-Print Network [OSTI]

    Kumar, Satish; Fisk, William J.

    2002-01-01T23:59:59.000Z

    of an effect of IAQ on productivity, and this is stated. 26.Effects on Productivity. Proceedings of IAQ ‘96: Paths toEffects on Productivity. Proceedings of IAQ ‘96: Paths to

  3. The role of emerging energy-efficient technology in promoting workplace productivity and health: Final report

    E-Print Network [OSTI]

    Kumar, Satish; Fisk, William J.

    2002-01-01T23:59:59.000Z

    of an effect of IAQ on productivity, and this is stated. 26.Effects on Productivity. Proceedings of IAQ ‘96: Paths toEffects on Productivity. Proceedings of IAQ ‘96: Paths to

  4. X-ray CT Observations of Methane Hydrate Distribution Changes over Time in a Natural Sediment Core from the BPX-DOE-USGS Mount Elbert Gas Hydrate Stratigraphic Test Well

    E-Print Network [OSTI]

    Kneafsey, T.J.

    2012-01-01T23:59:59.000Z

    and Englezos, P. , 2009. Gas hydrate formation in a variable1999. Formation of natural gas hydrates in marine sediments.1. Conceptual model of gas hydrate growth conditioned by

  5. DOE Hydrogen, Fuel Cells and Infrastructure Technologies Program Integrated Hydrogen Production, Purification and Compression System

    SciTech Connect (OSTI)

    Tamhankar, Satish; Gulamhusein, Ali; Boyd, Tony; DaCosta, David; Golben, Mark

    2011-06-30T23:59:59.000Z

    The project was started in April 2005 with the objective to meet the DOE target of delivered hydrogen of <$1.50/gge, which was later revised by DOE to $2-$3/gge range for hydrogen to be competitive with gasoline as a fuel for vehicles. For small, on-site hydrogen plants being evaluated at the time for refueling stations (the 'forecourt'), it was determined that capital cost is the main contributor to the high cost of delivered hydrogen. The concept of this project was to reduce the cost by combining unit operations for the entire generation, purification, and compression system (refer to Figure 1). To accomplish this, the Fluid Bed Membrane Reactor (FBMR) developed by MRT was used. The FBMR has hydrogen selective, palladium-alloy membrane modules immersed in the reformer vessel, thereby directly producing high purity hydrogen in a single step. The continuous removal of pure hydrogen from the reformer pushes the equilibrium 'forward', thereby maximizing the productivity with an associated reduction in the cost of product hydrogen. Additional gains were envisaged by the integration of the novel Metal Hydride Hydrogen Compressor (MHC) developed by Ergenics, which compresses hydrogen from 0.5 bar (7 psia) to 350 bar (5,076 psia) or higher in a single unit using thermal energy. Excess energy from the reformer provides up to 25% of the power used for driving the hydride compressor so that system integration improved efficiency. Hydrogen from the membrane reformer is of very high, fuel cell vehicle (FCV) quality (purity over 99.99%), eliminating the need for a separate purification step. The hydride compressor maintains hydrogen purity because it does not have dynamic seals or lubricating oil. The project team set out to integrate the membrane reformer developed by MRT and the hydride compression system developed by Ergenics in a single package. This was expected to result in lower cost and higher efficiency compared to conventional hydrogen production technologies. The overall objective was to develop an integrated system to directly produce high pressure, high-purity hydrogen from a single unit, which can meet the DOE cost H2 cost target of $2 - $3/gge when mass produced. The project was divided into two phases with the following tasks and corresponding milestones, targets and decision points. Phase 1 - Task 1 - Verify feasibility of the concept, perform a detailed techno-economic analysis, and develop a test plan; and Task 2: Build and experimentally test a Proof of Concept (POC) integrated membrane reformer/metal hydride compressor system. Phase 2 - Task 3: Build an Advanced Prototype (AP) system with modifications based on POC learning and demonstrate at a commercial site; and Task 4: Complete final product design for mass manufacturing units capable of achieving DOE 2010 H2 cost and performance targets.

  6. Insights into the structure of mixed CO2/CH4 in gas hydrates

    SciTech Connect (OSTI)

    Everett, Susan M [ORNL; Rawn, Claudia J [ORNL; Chakoumakos, Bryan C [ORNL; Keffer, David J. [University of Tennessee, Knoxville (UTK); Huq, Ashfia [ORNL; Phelps, Tommy Joe [ORNL

    2015-01-01T23:59:59.000Z

    The exchange of CO2 for CH4 in natural gas hydrates is an attractive approach to methane for energy production while simultaneously sequestering CO2. In addition to the energy and environmental implications, the solid solution of clathrate hydrate (CH4)1-x(CO2)x 5.75H2O provides a model system to study how the distinct bonding and shapes of CH4 and CO2 influence the structure and properties of the compound. High-resolution neutron diffraction was used to examine mixed CO2/CH4 gas hydrates. CO2-rich hydrates had smaller lattice parameters, which were attributed to the higher affinity of the CO2 molecule interacting with H2O molecules that form the surrounding cages, and resulted in a reduction in the unit cell volume. Experimental nuclear scattering densities illustrate how the cage occupants and energy landscape change with composition. These results provide important insights on the impact and mechanisms for exchanging CH4 and CO2.

  7. X-ray computed-tomography observations of water flow through anisotropic methane hydrate-bearing sand

    E-Print Network [OSTI]

    Seol, Yongkoo

    2010-01-01T23:59:59.000Z

    Formation of natural gas hydrates in marine sediments 1.Conceptual model of gas hydrate growth conditioned by hostPotential effects of gas hydrate on human welfare, Proc.

  8. Comparison of Kinetic and Equilibrium Reaction Models in Simulating the Behavior of Gas Hydrates in Porous Media

    E-Print Network [OSTI]

    Kowalsky, Michael B.; Moridis, George J.

    2006-01-01T23:59:59.000Z

    rate constant of methane gas hydrate decomposition, CanadianAdvances in the Study of Gas Hydrates, C. Taylor , J. Qwan,International Conference on Gas Hydrates, Trondheim, Norway,

  9. IN-SITU SAMPLING AND CHARACTERIZATION OF NATURALLY OCCURRING MARINE METHANE HYDRATE USING THE D/V JOIDES RESOLUTION

    SciTech Connect (OSTI)

    Frank R. Rack; Tim Francis; Peter Schultheiss; Philip E. Long; Barry M. Freifeld

    2005-04-01T23:59:59.000Z

    The primary activities accomplished during this quarter were continued efforts to develop plans for Phase 2 of this cooperative agreement based on the evolving operational planning for IODP Expedition 311, which will use the JOIDES Resolution to study marine methane hydrates along the Cascadia margin, offshore Vancouver Island. IODP Expedition 311 has been designed to further constrain the models for the formation of marine gas hydrate in subduction zone accretionary prisms. The objectives include characterizing the deep origin of the methane, its upward transport, its incorporation in gas hydrate, and its subsequent loss to the seafloor. The main attention of this expedition is on the widespread seafloor-parallel layer of dispersed gas hydrate located just above the base of the predicted stability field. In a gas hydrate formation model, methane is carried upward through regional sediment or small-scale fracture permeability, driven by the tectonic consolidation of the accretionary prism. The upward moving methane is incorporated into the gas hydrate clathrate as it enters the methane hydrate stability zone. Also important is the focusing of a portion of the upward methane flux into localized plumes or channels to form concentrations of near-seafloor gas hydrate. The amount of gas hydrate in local concentrations near the seafloor is especially important for understanding the response of marine gas hydrate to climate change. The expedition includes coring and downhole measurements at five sites across the Northern Cascadia accretionary prism. The sites will track the history of methane in an accretionary prism from (1) its production by mainly microbiological processes over a thick sediment vertical extent, (2) its upward transport through regional or locally focused fluid flow, (3) its incorporation in the regional hydrate layer above the BSR or in local concentrations at or near the seafloor, (4) methane loss from the hydrate by upward diffusion, and (5) methane oxidation and incorporation in seafloor carbonate, or expulsion to the ocean. This expedition builds on the previous Cascadia gas hydrate drilling of ODP Leg 146 and on more recent ODP Leg 204 off Oregon. Important experiments being considered for DOE/NETL funding as part of the JOI cooperative agreement include, (1) Logging-While-Drilling/Measurements-While-Drilling (LWD/MWD), (2) Pressure Core Sampling (PCS/HYACINTH) of gas hydrate, and fluid recovery under in situ conditions, (3) X-ray CT logging of whole cores under in situ conditions, and (4) Infrared thermal imaging of whole round cores to map temperature variations resulting from the presence of hydrate. Preliminary budget estimates have been made for each of these tasks and discussions are ongoing with DOE/NETL program managers to develop a final plan that can be implemented within the constraints of the available funding and logistical considerations.

  10. Emerging Energy-efficiency and CO{sub 2} Emission-reduction Technologies for Cement and Concrete Production

    SciTech Connect (OSTI)

    Hasanbeigi, Ali; Price, Lynn; Lin, Elina

    2012-04-06T23:59:59.000Z

    Globally, the cement industry accounts for approximately 5 percent of current anthropogenic carbon dioxide (CO{sub 2}) emissions. World cement demand and production are increasing significantly, leading to an increase in this industry's absolute energy use and CO{sub 2} emissions. Development of new energy-efficiency and CO{sub 2} emission-reduction technologies and their deployment in the market will be key for the cement industry's mid- and long-term climate change mitigation strategies. This report is an initial effort to compile available information on process description, energy savings, environmental and other benefits, costs, commercialization status, and references for emerging technologies to reduce the cement industry's energy use and CO{sub 2} emissions. Although studies from around the world identify a variety of sector-specific and cross-cutting energy-efficiency technologies for the cement industry that have already been commercialized, information is scarce and/or scattered regarding emerging or advanced energy-efficiency and low-carbon technologies that are not yet commercialized. This report consolidates available information on nineteen emerging technologies for the cement industry, with the goal of providing engineers, researchers, investors, cement companies, policy makers, and other interested parties with easy access to a well-structured database of information on these technologies.

  11. THERMODYNAMIC MODELLING OF GAS SEMI-CLATHRATE HYDRATES USING THE ELECTROLYTE NRTL MODEL

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    THERMODYNAMIC MODELLING OF GAS SEMI-CLATHRATE HYDRATES USING THE ELECTROLYTE NRTL MODEL Matthias. For the description of the gas semiclathrate hydrate phase a combination of the salt hydrate model of Paricaud the applicability of the approach presented. Keywords: modeling, semiclathrate hydrate, gas semiclathrate hydrate, e

  12. Resource Characterization and Quantification of Natural Gas-Hydrate and Associated Free-Gas Accumulations in the Prudhoe Bay - Kuparuk River Area on the North Slope of Alaska

    SciTech Connect (OSTI)

    Shirish Patil; Abhijit Dandekar

    2008-12-31T23:59:59.000Z

    Natural gas hydrates have long been considered a nuisance by the petroleum industry. Hydrates have been hazards to drilling crews, with blowouts a common occurrence if not properly accounted for in drilling plans. In gas pipelines, hydrates have formed plugs if gas was not properly dehydrated. Removing these plugs has been an expensive and time-consuming process. Recently, however, due to the geologic evidence indicating that in situ hydrates could potentially be a vast energy resource of the future, research efforts have been undertaken to explore how natural gas from hydrates might be produced. This study investigates the relative permeability of methane and brine in hydrate-bearing Alaska North Slope core samples. In February 2007, core samples were taken from the Mt. Elbert site situated between the Prudhoe Bay and Kuparuk oil fields on the Alaska North Slope. Core plugs from those core samples have been used as a platform to form hydrates and perform unsteady-steady-state displacement relative permeability experiments. The absolute permeability of Mt. Elbert core samples determined by Omni Labs was also validated as part of this study. Data taken with experimental apparatuses at the University of Alaska Fairbanks, ConocoPhillips laboratories at the Bartlesville Technology Center, and at the Arctic Slope Regional Corporation's facilities in Anchorage, Alaska, provided the basis for this study. This study finds that many difficulties inhibit the ability to obtain relative permeability data in porous media-containing hydrates. Difficulties include handling unconsolidated cores during initial core preparation work, forming hydrates in the core in such a way that promotes flow of both brine and methane, and obtaining simultaneous two-phase flow of brine and methane necessary to quantify relative permeability using unsteady-steady-state displacement methods.

  13. Multicavity SCRF calculation of ion hydration energies

    SciTech Connect (OSTI)

    Diercksen, B.H.F. [Max-Planck-Institut Fuer Astrophysik, Muenchen (Germany); Karelson, M. [Univ. of Tartu (Estonia); Tamm, T. [Univ. of Florida, Gainesville, FL (United States)

    1994-12-31T23:59:59.000Z

    The hydration energies of the proton, hydroxyl ion, and several inorganic ions were calculated using the multicavity self-consistent reaction field (MCa SCRF) method developed for the quantum-mechanical modeling of rotationally or flexible systems in dielectric media. The ionic complexes H{sub 3}O{sup +}(H2O){sub 4}, OH{sup {minus}}(H2O){sub 4}, NH{sup +}{sub 4}(H2O){sub 4}, and Hal{sup {minus}}(H2O){sub 4}, where Hal = F, Cl, or Br, have been studied. Each complex was divided between five spheres, corresponding to the central ion and four water molecules in their first coordination sphere, respectively. Each cavity was surrounded by a polarizable medium with the dielectric permittivity of water at room temperature (80). The ionic hydration energies of ions were divided into specific and nonspecific parts. After accounting for the cavity-formation energy using scaled particle theory, good agreement between the total calculated and experimental hydration energies was obtained for all ions studied.

  14. Emerging Energy-efficiency and CO2 Emission-reduction Technologies for Cement and Concrete Production

    E-Print Network [OSTI]

    Hasanbeigi, Ali

    2013-01-01T23:59:59.000Z

    International Energy Agency (IEA). 2007. Tracking IndustrialInternational Energy Agency (IEA). 2009a. Cement TechnologyInternational Energy Agency (IEA). 2009b. Cement roadmap

  15. Essays on regional and firm-level productivity, military spending, and technology

    E-Print Network [OSTI]

    Goudie, Bryan Daniel

    2008-01-01T23:59:59.000Z

    BLDG & REPAIRING GENERAL ELECTRIC CO CONGLOMERATES GENERALINC GENERAL DYNAMICS CORP GENERAL ELECTRIC CO GENERAL MOTORSCo Northrop Grumman General Dynamics United Technologies General Electric

  16. Emerging Energy-efficiency and CO2 Emission-reduction Technologies for Cement and Concrete Production

    E-Print Network [OSTI]

    Hasanbeigi, Ali

    2013-01-01T23:59:59.000Z

    2010. Cement and concrete nanoscience and nanotechnology.of 100 Percent Fly Ash Concrete. 2005 World of Coal Ash (carbon dioxide in precast concrete. TECHNOLOGY REVIEW – A

  17. Emerging Energy-efficiency and CO2 Emission-reduction Technologies for Cement and Concrete Production

    E-Print Network [OSTI]

    Hasanbeigi, Ali

    2013-01-01T23:59:59.000Z

    and/or used in enhanced oil recovery. This technology can beCO 2 for underground storage, enhanced oil recovery or other

  18. INCREASING HEAVY OIL RESERVES IN THE WILMINGTON OIL FIELD THROUGH ADVANCED RESERVOIR CHARACTERIZATION AND THERMAL PRODUCTION TECHNOLOGIES

    SciTech Connect (OSTI)

    Scott Hara

    2001-06-27T23:59:59.000Z

    The objective of this project is to increase the recoverable heavy oil reserves within sections of the Wilmington Oil Field, near Long Beach, California through the testing and application of advanced reservoir characterization and thermal production technologies. The successful application of these technologies will result in expanding their implementation throughout the Wilmington Field and, through technology transfer, to other slope and basin clastic (SBC) reservoirs. The existing steamflood in the Tar zone of Fault Block II-A (Tar II-A) has been relatively inefficient because of several producibility problems which are common in SBC reservoirs: inadequate characterization of the heterogeneous turbidite sands, high permeability thief zones, low gravity oil and non-uniform distribution of the remaining oil. This has resulted in poor sweep efficiency, high steam-oil ratios, and early steam breakthrough. Operational problems related to steam breakthrough, high reservoir pressure, and unconsolidated sands have caused premature well and downhole equipment failures. In aggregate, these reservoir and operational constraints have resulted in increased operating costs and decreased recoverable reserves. A suite of advanced reservoir characterization and thermal production technologies are being applied during the project to improve oil recovery and reduce operating costs.

  19. Breakthrough Water Cleaning Technology Could Lessen Environmental Impacts from Shale Production

    Broader source: Energy.gov [DOE]

    A novel water cleaning technology currently being tested in field demonstrations could help significantly reduce potential environmental impacts from producing natural gas from the Marcellus shale and other geologic formations, according to the Department of Energy’s National Energy Technology Laboratory

  20. Task 1.13 - Data Collection and Database Development for Clean Coal Technology By-Product Characteristics and Management Practices

    SciTech Connect (OSTI)

    Debra F. Pflughoeft-Hassett

    1998-02-01T23:59:59.000Z

    U.S. Department of Energy Federal Energy Technology Center-Morgantown (DOE FETC) efforts in the areas of fossil fuels and clean coal technology (CCT) have included involvement with both conventional and advanced process coal conversion by-products. In 1993, DOE submitted a Report to Congress on "Barriers to the Increased Utilization of Coal Combustion Desulfurization Byproducts by Governmental and Commercial Sectors" that provided an outline of activities to remove the barriers identified in the report. DOE charged itself with participation in this process, and the work proposed in this document facilitates DOE's response to its own recommendations for action. The work reflects DOE's commitment to the coal combustion by-product (CCB) industry, to the advancement of clean coal technology, and to cooperation with other government agencies. Information from DOE projects and commercial endeavors in fluidized-bed combustion (FBC) and coal gasification is the focus of this task. The primary goal is to provide an easily accessible compilation of characterization information on the by-products from these processes to government agencies and industry to facilitate sound regulatory and management decisions. Additional written documentation will facilitate the preparation of an updated final version of background information collected for DOE in preparation of the Report to Congress on barriers to CCB utilization.

  1. Dissolved carbonic anhydrase for enhancing post-combustion carbon dioxide hydration in aqueous ammonia

    SciTech Connect (OSTI)

    Collett, James R.; Heck, Robert W.; Zwoster, Andy

    2011-04-01T23:59:59.000Z

    Aqueous ammonia solvents that capture CO2 as ionic complexes of carbonates with ammonium have recently been advanced as alternatives to amine-based solvents due to their lower energy requirements for thermal regeneration. In ammonia based solvents, the hydration of CO2 to form bicarbonate may become a rate-limiting step as the CO2 loading increases and the resulting pH level of the solvent decreases. Variants of the enzyme carbonic anhydrase can accelerate the reversible hydration of CO2 to yield bicarbonate by more than 10(6)-fold. The possible benefit of bovine carbonic anhydrase (BCA) addition to solutions of aqueous ammonia to enhance CO2 hydration was investigated in semi-batch reactions within continuously stirred tank reactors or in a bubble column gas-liquid contactor. Adding 154 mg/liter of BCA to 2 M aqueous ammonia provided a 34.1% overall increase in the rate of CO2 hydration (as indicated by the production of [H+]) as the pH declined from 9.6 to 8.6 during sparging with a 15% CO2, 85% N-2 gas at a flow rate of 3 lpm. The benefits of adding BCA to enhance CO2 hydration were only discernable below similar to pH 9. The implications of the apparent pH limitations on the utility of BCA are discussed in the context of absorber unit operation design. Possible embodiments of carbonic anhydrase as either an immobilized catalyst or as a dissolved, recirculating catalyst in potential plant scale aqueous ammonia systems are considered as well. (C) 2010 Published by Elsevier Ltd.

  2. Geology, reservoir engineering and methane hydrate potential of the Walakpa Gas Field, North Slope, Alaska

    SciTech Connect (OSTI)

    Glenn, R.K.; Allen, W.W.

    1992-12-01T23:59:59.000Z

    The Walakpa Gas Field, located near the city of Barrow on Alaska's North Slope, has been proven to be methane-bearing at depths of 2000--2550 feet below sea level. The producing formation is a laterally continuous, south-dipping, Lower Cretaceous shelf sandstone. The updip extent of the reservoir has not been determined by drilling, but probably extends to at least 1900 feet below sea level. Reservoir temperatures in the updip portion of the reservoir may be low enough to allow the presence of in situ methane hydrates. Reservoir net pay however, decreases to the north. Depths to the base of permafrost in the area average 940 feet. Drilling techniques and production configuration in the Walakpa field were designed to minimize formation damage to the reservoir sandstone and to eliminate methane hydrates formed during production. Drilling development of the Walakpa field was a sequential updip and lateral stepout from a previously drilled, structurally lower confirmation well. Reservoir temperature, pressure, and gas chemistry data from the development wells confirm that they have been drilled in the free-methane portion of the reservoir. Future studies in the Walakpa field are planned to determine whether or not a component of the methane production is due to the dissociation of updip in situ hydrates.

  3. Examination of Hydrate Formation Methods: Trying to Create Representative Samples

    E-Print Network [OSTI]

    Kneafsey, T.J.

    2012-01-01T23:59:59.000Z

    Methods: Trying to Create Representative Samples Timothy J.Methods: Trying to Create Representative Samples Timothy J.Introduction Forming representative gas hydrate-bearing

  4. Method for the photocatalytic conversion of gas hydrates

    DOE Patents [OSTI]

    Taylor, Charles E. (Pittsburg, PA); Noceti, Richard P. (Pittsburg, PA); Bockrath, Bradley C. (Bethel Park, PA)

    2001-01-01T23:59:59.000Z

    A method for converting methane hydrates to methanol, as well as hydrogen, through exposure to light. The process includes conversion of methane hydrates by light where a radical initiator has been added, and may be modified to include the conversion of methane hydrates with light where a photocatalyst doped by a suitable metal and an electron transfer agent to produce methanol and hydrogen. The present invention operates at temperatures below 0.degree. C., and allows for the direct conversion of methane contained within the hydrate in situ.

  5. Energy Department Expands Research into Methane Hydrates, a Vast...

    Broader source: Energy.gov (indexed) [DOE]

    of methane in shallow subsurface and water columns, and the role gas hydrates play in carbon cycling. DOE Investment: approximately 650,000 Massachusetts Institute of...

  6. airway surface hydration: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    I. Introduction Cementpaste,the binding phaseof concrete Bentz, Dale P. 200 NISTIR 7232 CEMHYD3D: A Three-Dimensional Cement Hydration Engineering Websites Summary: NISTIR...

  7. angiogenesis vascularity hydration: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    I. Introduction Cementpaste,the binding phaseof concrete Bentz, Dale P. 177 NISTIR 7232 CEMHYD3D: A Three-Dimensional Cement Hydration Engineering Websites Summary: NISTIR...

  8. alaskan gas hydrate: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    I. Introduction Cementpaste,the binding phaseof concrete Bentz, Dale P. 224 NISTIR 7232 CEMHYD3D: A Three-Dimensional Cement Hydration Engineering Websites Summary: NISTIR...

  9. aluminum hydration effects: Topics by E-print Network

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    I. Introduction Cementpaste,the binding phaseof concrete Bentz, Dale P. 258 NISTIR 7232 CEMHYD3D: A Three-Dimensional Cement Hydration Engineering Websites Summary: NISTIR...

  10. Increasing gas hydrate formation temperature for desalination of high salinity produced water with secondary guests

    SciTech Connect (OSTI)

    Cha, Jong-Ho [ORISE; Seol, Yongkoo [U.S. DOE

    2013-01-01T23:59:59.000Z

    We suggest a new gas hydrate-based desalination process using water-immiscible hydrate formers; cyclopentane (CP) and cyclohexane (CH) as secondary hydrate guests to alleviate temperature requirements for hydrate formation. The hydrate formation reactions were carried out in an isobaric condition of 3.1 MPa to find the upper temperature limit of CO2 hydrate formation. Simulated produced water (8.95 wt % salinity) mixed with the hydrate formers shows an increased upper temperature limit from ?2 °C for simple CO2 hydrate to 16 and 7 °C for double (CO2 + CP) and (CO2 + CH) hydrates, respectively. The resulting conversion rate to double hydrate turned out to be similar to that with simple CO2 hydrate at the upper temperature limit. Hydrate formation rates (Rf) for the double hydrates with CP and CH are shown to be 22 and 16 times higher, respectively, than that of the simple CO2 hydrate at the upper temperature limit. Such mild hydrate formation temperature and fast formation kinetics indicate increased energy efficiency of the double hydrate system for the desalination process. Dissociated water from the hydrates shows greater than 90% salt removal efficiency for the hydrates with the secondary guests, which is also improved from about 70% salt removal efficiency for the simple hydrates.

  11. A Review of Emerging Energy-efficiency and CO2 Emission-reduction Technologies for Cement and Concrete Production

    E-Print Network [OSTI]

    Hasanbeigi, Ali

    2014-01-01T23:59:59.000Z

    301–314. New Energy and Industrial Technology Development (Group Environmental Energy Technologies Division Lawrenceproceedings, Industrial Energy Technology Conference (IETC)

  12. Occurrence of gas hydrate in Oligocene Frio sand: Alaminos Canyon Block 818: Northern Gulf of Mexico

    E-Print Network [OSTI]

    Boswell, R.D.

    2010-01-01T23:59:59.000Z

    Advances in the Study of Gas Hydrates. Kluwer, New York, pp.and quantification of gas hydrates using rock physics andand Salt Inhibition of Gas Hydrate Formation in the Northern

  13. Estimation of composite thermal conductivity of a heterogeneous methane hydrate sample using iTOUGH2

    E-Print Network [OSTI]

    Gupta, Arvind; Kneafsey, Timothy J.; Moridis, George J.; Seol, Yongkoo; Kowalsky, Michael B.; Sloan Jr., E.D.

    2006-01-01T23:59:59.000Z

    International Conference on Gas Hydrates, Trondheim, Norway,Challenges for the future/gas hydrates, NYAS 912, 304, 2000.C. , Thermal state of the gas hydrate reservoir, natural gas

  14. Development of a Numerical Simulator for Analyzing the Geomechanical Performance of Hydrate-Bearing Sediments

    E-Print Network [OSTI]

    Rutqvist, J.

    2008-01-01T23:59:59.000Z

    J. Mienert. 2004. Effect of gas hydrates melting on seafloorInternational Conference on Gas Hydrates, Trondheim, Norway,A Documented Example of Gas Hydrate Saturated Sand in the

  15. The dynamic response of oceanic hydrate deposits to ocean temperature change

    E-Print Network [OSTI]

    Reagan, Matthew T.

    2008-01-01T23:59:59.000Z

    Moridis, G.J. (2007), Oceanic gas hydrate instability andand salt inhibition of gas hydrate formation in the northernI.R. (1999), Thermogenic gas hydrates and hydrocarbon gases

  16. Hydration-dependent dynamics of deeply cooled water under strong confinement

    E-Print Network [OSTI]

    Bertrand, C. E.

    We have measured the hydration-level dependence of the single-particle dynamics of water confined in the ordered mesoporous silica MCM-41. The dynamic crossover observed at full hydration is absent at monolayer hydration. ...

  17. Comparison of kinetic and equilibrium reaction models in simulating gas hydrate behavior in porous media

    E-Print Network [OSTI]

    Kowalsky, Michael B.; Moridis, George J.

    2006-01-01T23:59:59.000Z

    with Diapirism and Gas Hydrates at the Head of the Cape FearSea-Level Low Stands Above Gas Hydrate-Bearing Sediments.rate constant of methane gas hydrate decomposition. Canadian

  18. Occurrence of gas hydrate in Oligocene Frio sand: Alaminos Canyon Block 818: Northern Gulf of Mexico

    E-Print Network [OSTI]

    Boswell, R.D.

    2010-01-01T23:59:59.000Z

    and quantification of gas hydrates using rock physics andAdvances in the Study of Gas Hydrates. Kluwer, New York, pp.and Salt Inhibition of Gas Hydrate Formation in the Northern

  19. Modeling of Oceanic Gas Hydrate Instability and Methane Release in Response to Climate Change

    E-Print Network [OSTI]

    Reagan, Matthew T.

    2008-01-01T23:59:59.000Z

    Potential effects of gas hydrate on human welfare. Proc.W.S. A review of methane and gas hydrates in the dynamic,Geology of Natural Gas Hydrates, M. Max, A.H. Johnson, W.P.

  20. Basin scale assessment of gas hydrate dissociation in response to climate change

    E-Print Network [OSTI]

    Reagan, M.

    2012-01-01T23:59:59.000Z

    Moridis GJ. Oceanic gas hydrate instability and dissociationKA. Potential effects of gas hydrate on human welfare, Proc.WS. A review of methane and gas hydrates in the dynamic,

  1. Contribution of oceanic gas hydrate dissociation to the formation of Arctic Ocean methane plumes

    E-Print Network [OSTI]

    Reagan, M.

    2012-01-01T23:59:59.000Z

    V.A. Soloviev, Submarine Gas Hydrates. St. Petersburg, 1998.and stability of gas hydrate-related bottom-simulatingPotential effects of gas hydrate on human welfare, Proc.

  2. INCREASING HEAVY OIL RESERVES IN THE WILMINGTON OIL FIELD THROUGH ADVANCED RESERVOIR CHARACTERIZATION AND THERMAL PRODUCTION TECHNOLOGIES

    SciTech Connect (OSTI)

    Unknown

    2001-08-08T23:59:59.000Z

    The objective of this project is to increase the recoverable heavy oil reserves within sections of the Wilmington Oil Field, near Long Beach, California, through the testing and application of advanced reservoir characterization and thermal production technologies. The hope is that successful application of these technologies will result in their implementation throughout the Wilmington Field and, through technology transfer, will be extended to increase the recoverable oil reserves in other slope and basin clastic (SBC) reservoirs. The existing steamflood in the Tar zone of Fault Block II-A (Tar II-A) has been relatively inefficient because of several producibility problems which are common in SBC reservoirs: inadequate characterization of the heterogeneous turbidite sands, high permeability thief zones, low gravity oil and non-uniform distribution of the remaining oil. This has resulted in poor sweep efficiency, high steam-oil ratios, and early steam breakthrough. Operational problems related to steam breakthrough, high reservoir pressure, and unconsolidated sands have caused premature well and downhole equipment failures. In aggregate, these reservoir and operational constraints have resulted in increased operating costs and decreased recoverable reserves. A suite of advanced reservoir characterization and thermal production technologies are being applied during the project to improve oil recovery and reduce operating costs, including: (1) Development of three-dimensional (3-D) deterministic and stochastic reservoir simulation models--thermal or otherwise--to aid in reservoir management of the steamflood and post-steamflood phases and subsequent development work. (2) Development of computerized 3-D visualizations of the geologic and reservoir simulation models to aid reservoir surveillance and operations. (3) Perform detailed studies of the geochemical interactions between the steam and the formation rock and fluids. (4) Testing and proposed application of a novel alkaline-steam well completion technique for the containment of the unconsolidated formation sands and control of fluid entry and injection profiles. (5) Installation of a 2100 ft, 14 inch insulated, steam line beneath a harbor channel to supply steam to an island location. (6) Testing and proposed application of thermal recovery technologies to increase oil production and reserves: (a) Performing pilot tests of cyclic steam injection and production on new horizontal wells. (b) Performing pilot tests of hot water-alternating-steam (WAS) drive in the existing steam drive area to improve thermal efficiency. (7) Perform a pilot steamflood with the four horizontal injectors and producers using a pseudo steam-assisted gravity-drainage (SAGD) process. (8) Advanced reservoir management, through computer-aided access to production and geologic data to integrate reservoir characterization, engineering, monitoring and evaluation.

  3. Methane hydrate distribution from prolonged and repeated formation in natural and compacted sand samples: X-ray CT observations

    E-Print Network [OSTI]

    Rees, E.V.L.

    2012-01-01T23:59:59.000Z

    K. and McDonald, T. , Gas Hydrates of the Middle Americaet al. , Indian National Gas Hydrate Program Expedition 01et al. , Drilling Gas Hydrates on Hydrate Ridge, Cascadia

  4. Surfactant process for promoting gas hydrate formation and application of the same

    DOE Patents [OSTI]

    Rogers, Rudy E. (Starkville, MS); Zhong, Yu (Brandon, MS)

    2002-01-01T23:59:59.000Z

    This invention relates to a method of storing gas using gas hydrates comprising forming gas hydrates in the presence of a water-surfactant solution that comprises water and surfactant. The addition of minor amounts of surfactant increases the gas hydrate formation rate, increases packing density of the solid hydrate mass and simplifies the formation-storage-decomposition process of gas hydrates. The minor amounts of surfactant also enhance the potential of gas hydrates for industrial storage applications.

  5. SELECTING INFORMATION TECHNOLOGY SECURITY

    E-Print Network [OSTI]

    April 2004 SELECTING INFORMATION TECHNOLOGY SECURITY PRODUCTS Shirley Radack, Editor Computer Security Division Information Technology Laboratory National Institute of Standards and Technology Information technology security prod ucts are essential to better secure infor mation technology (IT) systems

  6. Creating ladders out of chains : China's technological development in a world of global production

    E-Print Network [OSTI]

    Fuller, Douglas Brian

    2005-01-01T23:59:59.000Z

    With the advent of economic globalization, the terms of debate over the political and social conditions necessary to foster development in the Global South have shifted. Examining technological development, one important ...

  7. Vehicle Technologies Office Merit Review 2015: Lithium-Ion Battery Production and Recycling Materials Issues

    Broader source: Energy.gov [DOE]

    Presentation given by Argonne National Laboratory at 2015 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Office Annual Merit Review and Peer Evaluation Meeting about lithium-ion...

  8. Automobiles on steroids: Product attribute trade-offs and technological progress in the automobile sector

    E-Print Network [OSTI]

    Knittel, Christopher Roland

    This paper estimates the technological progress that has occurred since 1980 in the automobile industry and the trade-offs faced when choosing between fuel economy, weight, and engine power characteristics. The results ...

  9. Enzymatically based cellulosic ethanol production technology was selected as a key area for biomass

    E-Print Network [OSTI]

    California at Riverside, University of

    of biotechnology offered the promise for significant advances that could dramati- cally reduce costs and make Laboratory, PO Box 2008, Oak Ridge, Tennessee, USA 5 Center for Environmental Research & Technology, Bourns

  10. DOE Announces Selections for SSL Core Technology and Product Development Funding Opportunities (Round 5)

    Broader source: Energy.gov [DOE]

    The National Energy Technology Laboratory, on behalf of the U.S. Department of Energy (DOE), is pleased to announce its selections for solid-state lighting (SSL) funding opportunities. Fourteen...

  11. Investigating the Metastability of Clathrate Hydrates for Energy Storage

    SciTech Connect (OSTI)

    Koh, Carolyn Ann [Colorado School of Mines

    2014-11-18T23:59:59.000Z

    Important breakthrough discoveries have been achieved from the DOE award on the key processes controlling the synthesis and structure-property relations of clathrate hydrates, which are critical to the development of clathrate hydrates as energy storage materials. Key achievements include: (i) the discovery of key clathrate hydrate building blocks (stable and metastable) leading to clathrate hydrate nucleation and growth; (ii) development of a rapid clathrate hydrate synthesis route via a seeding mechanism; (iii) synthesis-structure relations of H2 + CH4/CO2 binary hydrates to control thermodynamic requirements for energy storage and sequestration applications; (iv) discovery of a new metastable phase present during clathrate hydrate structural transitions. The success of our research to-date is demonstrated by the significant papers we have published in high impact journals, including Science, Angewandte Chemie, J. Am. Chem. Soc. Intellectual Merits of Project Accomplishments: The intellectual merits of the project accomplishments are significant and transformative, in which the fundamental coupled computational and experimental program has provided new and critical understanding on the key processes controlling the nucleation, growth, and thermodynamics of clathrate hydrates containing hydrogen, methane, carbon dioxide, and other guest molecules for energy storage. Key examples of the intellectual merits of the accomplishments include: the first discovery of the nucleation pathways and dominant stable and metastable structures leading to clathrate hydrate formation; the discovery and experimental confirmation of new metastable clathrate hydrate structures; the development of new synthesis methods for controlling clathrate hydrate formation and enclathration of molecular hydrogen. Broader Impacts of Project Accomplishments: The molecular investigations performed in this project on the synthesis (nucleation & growth)-structure-stability relations of clathrate hydrate systems are pivotal in the fundamental understanding of crystalline clathrate hydrates and the discovery of new clathrate hydrate properties and novel materials for a broad spectrum of energy applications, including: energy storage (hydrogen, natural gas); carbon dioxide sequestration; controlling hydrate formation in oil/gas transportation in subsea pipelines. The Project has also enabled the training of undergraduate, graduate and postdoctoral students in computational methods, molecular spectroscopy and diffraction, and measurement methods at extreme conditions of high pressure and low temperature.

  12. Fundamental measure theory of hydrated hydrocarbons

    E-Print Network [OSTI]

    Victor F. Sokolov; Gennady N. Chuev

    2006-04-13T23:59:59.000Z

    To calculate the solvation of hydrophobic solutes we have developed the method based on the fundamental measure treatment of the density functional theory. This method allows us to carry out calculations of density profiles and the solvation energy for various hydrophobic molecules with a high accuracy. We have applied the method to the hydration of various hydrocarbons (linear, branched and cyclic). The calculations of the entropic and the enthalpic parts are also carried out. We have examined a question about temperature dependence of the entropy convergence. Finally, we have calculated the mean force potential between two large hydrophobic nanoparticles immersed in water.

  13. methane_hydrates | netl.doe.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOE Office of ScienceandMesa del SolStrengtheningWildfires mayYuan T.External Links ExternalMethane Hydrates Special

  14. Methane Hydrates R&D Program

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level: National5Sales for4,645U.S. DOEThe Bonneville PowerCherries 82981-1cnHighand Retrievals from aRodMIT-Harvard Center forMetallicH.Gas Hydrates

  15. Multi-Seam Well Completion Technology: Implications for Powder River Basin Coalbed Methane Production

    SciTech Connect (OSTI)

    Office of Fossil Energy; National Energy Technology Laboratory

    2003-09-01T23:59:59.000Z

    The purpose of this study is to evaluate the potential benefits of applying multiseam [well] completion (MSC) technology to the massive stack of low-rank coals in the Powder River Basin. As part of this, the study objectives are: Estimate how much additional CBM resource would become accessible and technically recoverable--compared to the current practice of drilling one well to drain a single coal seam; Determine whether there are economic benefits associated with MSC technology utilization (assuming its widespread, successful application) and if so, quantify the gains; Briefly examine why past attempts by Powder River Basin CBM operators to use MSC technology have been relatively unsuccessful; Provide the underpinnings to a decision whether a MSC technology development and/or demonstration effort is warranted by DOE. To a great extent, this assessment builds on the previously published study (DOE, 2002), which contains many of the key references that underlie this analysis. It is available on the U.S. Department of Energy, National Energy technology Laboratory, Strategic Center for Natural Gas website (www.netl.doe.gov/scng). It is suggested that readers obtain a copy of the original study to complement the current report.

  16. The role of emerging energy-efficient technology in promoting workplace productivity and health: Final report

    SciTech Connect (OSTI)

    Kumar, Satish; Fisk, William J.

    2002-02-01T23:59:59.000Z

    The objective of this particular Indoor Health and Productivity (IHP) project is to improve the communication of research findings in the indoor health and productivity area to scientists and building professionals (e.g. architects and engineers) and, thus, to help stimulate implementation of existing knowledge.

  17. CHARACTERIZATION OF MIXED CO2-TBPB HYDRATE FOR REFRIGERATION APPLICATIONS

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    CHARACTERIZATION OF MIXED CO2-TBPB HYDRATE FOR REFRIGERATION APPLICATIONS Pascal Clain , Anthony storage and distribution in refrigeration applications. Previous studies show that these hydrates are able.s] INTRODUCTION Secondary refrigeration is a method using a neutral fluid for cold distribution in order

  18. Seismic-Scale Rock Physics of Methane Hydrate

    SciTech Connect (OSTI)

    Amos Nur

    2009-01-08T23:59:59.000Z

    We quantify natural methane hydrate reservoirs by generating synthetic seismic traces and comparing them to real seismic data: if the synthetic matches the observed data, then the reservoir properties and conditions used in synthetic modeling might be the same as the actual, in-situ reservoir conditions. This approach is model-based: it uses rock physics equations that link the porosity and mineralogy of the host sediment, pressure, and hydrate saturation, and the resulting elastic-wave velocity and density. One result of such seismic forward modeling is a catalogue of seismic reflections of methane hydrate which can serve as a field guide to hydrate identification from real seismic data. We verify this approach using field data from known hydrate deposits.

  19. Design of generic coal conversion facilities: Production of oxygenates from synthesis gas---A technology review

    SciTech Connect (OSTI)

    Not Available

    1991-10-01T23:59:59.000Z

    This report concentrates on the production of oxygenates from coal via gasification and indirect liquefaction. At the present the majority of oxygenate synthesis programs are at laboratory scale. Exceptions include commercial and demonstration scale plants for methanol and higher alcohols production, and ethers such as MTBE. Research and development work has concentrated on elucidating the fundamental transport and kinetic limitations governing various reactor configurations. But of equal or greater importance has been investigations into the optimal catalyst composition and process conditions for the production of various oxygenates.

  20. Synthesis and characterization of a new structure of gas hydrate

    SciTech Connect (OSTI)

    Tulk, Christopher A [ORNL; Chakoumakos, Bryan C [ORNL; Ehm, Lars [Stony Brook University (SUNY); Klug, Dennis D [National Research Council of Canada; Parise, John B [Stony Brook University (SUNY); Yang, Ling [ORNL; Martin, Dave [Argonne National Laboratory (ANL); Ripmeester, John [National Research Council of Canada; Moudrakovski, Igor [National Research Council of Canada; Ratcliffe, Chris [National Research Council of Canada

    2009-01-01T23:59:59.000Z

    Atoms and molecules 0.4 0.9 nm in diameter can be incorporated in the cages formed by hydrogen-bonded water molecules making up the crystalline solid clathrate hydrates. There are three structural families of these hydrates , known as sI, sII and sH, and the structure usually depends on the largest guest molecule in the hydrate. Species such as Ar, Kr, Xe and methane form sI or sII hydrate, sH is unique in that it requires both small and large cage guests for stability. All three structures, containing methane, other hydrocarbons, H2S and CO2, O2 and N2 have been found in the geosphere, with sI methane hydrate by far the most abundant. At high pressures (P > 0.7 kbar) small guests (Ar, Kr, Xe, methane) are also known to form sH hydrate with multiple occupancy of the largest cage in the hydrate. The high-pressure methane hydrate of sH has been proposed as playing a role in the outer solar system, including formation models for Titan , and yet another high pressure phase of methane has been reported , although its structure remains unknown. In this study, we report a new and unique hydrate structure that is derived from the high pressure sH hydrate of xenon. After quench recovery at ambient pressure and 77 K it shows considerable stability at low temperatures (T < 160 K) and is compositionally similar to the sI Xe clathrate starting material. This evidence of structural complexity in compositionally similar clathrate compounds indicates that thermodynamic pressure temperature conditions may not be the only important factor in structure determination, but also the reaction path may have an important effect.

  1. Design manual for management of solid by-products from advanced coal technologies

    SciTech Connect (OSTI)

    NONE

    1994-10-01T23:59:59.000Z

    Developing coal conversion technologies face major obstacles in byproduct management. This project has developed several management strategies based on field trials of small-scale landfills in an earlier phase of the project, as well as on published/unpublished sources detailing regulatory issues, current industry practice, and reuse opportunities. Field testing, which forms the basis for several of the disposal alternatives presented in this design manual, was limited to byproducts from Ca-based dry SO{sub 2} control technologies, circulating fluidized bed combustion ash, and bubbling bed fluidized bed combustion ash. Data on byproducts from other advanced coal technologies and on reuse opportunities are drawn from other sources (citations following Chapter 3). Field results from the 5 test cases examined under this project, together with results from other ongoing research, provide a basis for predictive modeling of long-term performance of some advanced coal byproducts on exposure to ambient environment. This manual is intended to provide a reference database and development plan for designing, permitting, and operating facilities where advanced coal technology byproducts are managed.

  2. Hydrogen, Fuel Cells, and Infrastructure Technologies FY 2002 Progress Report Section II. Hydrogen Production and Delivery

    E-Print Network [OSTI]

    Renewable Energy Laboratory 1617 Cole Blvd. Golden, CO 80401 (303) 384-7705, fax: (303) 384-6363, e-mail: ed_wolfum@nrel.gov DOE Technology Development Manager: Roxanne Danz (202) 586-7260, fax: (202) 586-9811, e-mail: Roxanne. · Successfully operated trickle-bed bioreactors with volumes of 1L and 5L, and showed that the performance

  3. Lean effectiveness model for products and services : servicing existing systems in aerospace and technology

    E-Print Network [OSTI]

    Srivastava, Tina Prabha

    2012-01-01T23:59:59.000Z

    Enterprises undergo transformation for more efficient and effective performance and growth. The Lean Enterprise Self Assessment Tool (LESAT) is a product of the Lean Advancement Initiative (LAI) and the Massachusetts ...

  4. Emerging Energy-efficiency and CO2 Emission-reduction Technologies for Cement and Concrete Production

    E-Print Network [OSTI]

    Hasanbeigi, Ali

    2013-01-01T23:59:59.000Z

    Hilger, J. 2003. Combined Utilization of Oil Shale Energyand Oil Shale Minerals within the Production of Cement andOther Hydraulic Minerals. Oil Shale, Vol. 20, No. 3, pp.

  5. A Novel, Green Technology for the Production of Aromatic Thiol from Aromatic Sulfonyl Chloride

    E-Print Network [OSTI]

    Atkinson, Bradley R.

    2010-01-16T23:59:59.000Z

    The hydrogenation of aromatic sulfonyl chloride to produce aromatic thiol is an important industrial reaction. The aromatic thiol is a critical intermediate in the production of many pharmaceuticals as well as several agrochemicals. Density...

  6. A Review of Emerging Energy-efficiency and CO2 Emission-reduction Technologies for Cement and Concrete Production

    E-Print Network [OSTI]

    Hasanbeigi, Ali

    2014-01-01T23:59:59.000Z

    GmbH (ECRA), 2007. Carbon Capture Technology - Options and2.5. Emerging Carbon Capture Technologies for the Cementof emerging carbon capture technologies for the cement

  7. A Review of Emerging Energy-efficiency and CO2 Emission-reduction Technologies for Cement and Concrete Production

    E-Print Network [OSTI]

    Hasanbeigi, Ali

    2014-01-01T23:59:59.000Z

    efficiency and CO2 Emission-reduction Technologies forefficiency and CO2 Emission- reduction Technologies forefficiency and CO2 Emission-reduction Technologies The

  8. Geothermal Energy Production with Co-produced and Geopressured Resources (Fact Sheet), Geothermal Technologies Program (GTP)

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(Fact Sheet), Geothermal Technologies Program (GTP) | Department of

  9. CLATHRATE HYDRATES FORMATION IN SHORT-PERIOD COMETS

    SciTech Connect (OSTI)

    Marboeuf, Ulysse; Mousis, Olivier; Petit, Jean-Marc [Institut UTINAM, CNRS-UMR 6213, Observatoire de Besancon, BP 1615, 25010 Besancon Cedex (France); Schmitt, Bernard, E-mail: marboeuf@ujf-grenoble.f [Universite Joseph Fourier, Laboratoire de Planetologie de Grenoble, CNRS INSU (France)

    2010-01-01T23:59:59.000Z

    The initial composition of current models of cometary nuclei is only based on two forms of ice: crystalline ice for long-period comets and amorphous ice for short-period comets. A third form of ice, i.e., clathrate hydrate, could exist within the short-period cometary nuclei, but the area of formation of this crystalline structure in these objects has never been studied. Here, we show that the thermodynamic conditions in the interior of short-period comets allow the existence of clathrate hydrates in Halley-type comets. We show that their existence is viable in the Jupiter family comets only when the equilibrium pressure of CO clathrate hydrate is at least 1 order of magnitude lower than the usually assumed theoretical value. We calculate that the amount of volatiles that could be trapped in the clathrate hydrate layer may be orders of magnitude greater than the daily amount of gas released at the surface of the nucleus at perihelion. The formation and the destruction of the clathrate hydrate cages could then explain the diversity of composition of volatiles observed in comets, as well as some pre-perihelion outbursts. We finally show that the potential clathrate hydrate layer in comet 67P/Churyumov-Gerasimenko would, unfortunately, be deep inside the nucleus, out of reach of the Rosetta lander. However, such a clathrate hydrate layer would show up by the gas composition of the coma.

  10. Metal halogen battery system with multiple outlet nozzle for hydrate

    DOE Patents [OSTI]

    Bjorkman, Jr., Harry K. (Birmingham, MI)

    1983-06-21T23:59:59.000Z

    A metal halogen battery system, including at least one cell having a positive electrode and a negative electrode contacted by aqueous electrolyte containing the material of said metal and halogen, store means whereby halogen hydrate is formed and stored as part of an aqueous material, means for circulating electrolyte through the cell and to the store means, and conduit means for transmitting halogen gas formed in the cell to a hydrate former whereby the hydrate is formed in association with the store means, said store means being constructed in the form of a container which includes a filter means, said filter means being inoperative to separate the hydrate formed from the electrolyte, said system having, a hydrate former pump means associated with the store means and being operative to intermix halogen gas with aqueous electrolyte to form halogen hydrate, said hydrate former means including, multiple outlet nozzle means connected with the outlet side of said pump means and being operative to minimize plugging, said nozzle means being comprised of at least one divider means which is generally perpendicular to the rotational axes of gears within the pump means, said divider means acting to divide the flow from the pump means into multiple outlet flow paths.

  11. Increasing Heavy Oil Reserves in the Wilmington Oil Field through Advanced Reservoir Characterization and Thermal Production Technologies

    SciTech Connect (OSTI)

    City of Long Beach; David K.Davies and Associates; Tidelands Oil Production Company; University of Southern California

    1999-06-25T23:59:59.000Z

    The objective of this project is to increase the recoverable heavy oil reserves within sections of the Wilmington Oil Field, near Long Beach, California. This is realized through the testing and application of advanced reservoir characterization and thermal production technologies. It is hoped that the successful application of these technologies will result in their implementation throughout the Wilmington Field and through technology transfer, will be extended to increase the recoverable oil reserves in other slope and basin clastic (SBC) reservoirs. The existing steamflood in the Tar zone of Fault Block (FB) II-A has been relatively insufficient because of several producability problems which are common in SBC reservoir; inadequate characterization of the heterogeneous turbidite sands, high permeability thief zones, low gravity oil and non-uniform distribution of the remaining oil. This has resulted in poor sweep efficiency, high steam-oil ratios, and early breakthrough. Operational problems related to steam breakthrough, high reservoir pressure, and unconsolidated sands have caused premature well and downhole equipment failures. In aggregate, these reservoir and operational constraints have resulted in increased operating costs and decreased recoverable reserves.

  12. Cement & Concrete Science Conference: Leeds, 2009 Hydration of alite containing aluminium

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Cement & Concrete Science Conference: Leeds, 2009 Hydration of alite containing aluminium Begarin in cement is tricalcium silicate which leads during its hydration to the nucleation and growth of calcium silicate hydrate (referred to C-S-H (CaO)x-SiO2-(H2O)y). The development of this hydrate around the cement

  13. Micromechanics of Hydrate Dissociation in Marine Sediments by Grain-Scale Simulations

    E-Print Network [OSTI]

    Patzek, Tadeusz W.

    dissociation on the strength of hydrate-bearing sediments. Dissociation of gas-hydrates in marine sediments. Introduction Gas-hydrates are solid materials formed under a range of high pressures and low temperatures seek to evaluate the mechanical response to dissoci- ation of gas-hydrates in marine sediments

  14. E ects of the Driving Force on the Composition of Natural Gas Hydrates

    E-Print Network [OSTI]

    Gudmundsson, Jon Steinar

    E ects of the Driving Force on the Composition of Natural Gas Hydrates Odd I. Levik(1) , Jean for storage and transport of natural gas. Storage of natural gas in the form of hydrate at elevated pressure concept) (Gud- mundsson et al. 1998). Natural gas hydrate contains up to 182 Sm3 gas per m3 hydrate

  15. Driving force and composition for multicomponent gas hydrate nucleation from supersaturated aqueous solutions

    E-Print Network [OSTI]

    Firoozabadi, Abbas

    formation in storage. Other interests include deep ocean carbon sequestration, use of hydrate deposits

  16. Comparison of kinetic and equilibrium reaction models in simulating gas hydrate behavior in porous media

    E-Print Network [OSTI]

    Kowalsky, Michael B.; Moridis, George J.

    2006-01-01T23:59:59.000Z

    hydrocarbons residing in hydrate deposits is estimated to substantially exceed all known conventional

  17. Geophysical constraints on the surface distribution of authigenic carbonates across the Hydrate Ridge region,

    E-Print Network [OSTI]

    Goldfinger, Chris

    the shallow source of methane and water contained in subsurface and surface gas hydrates. The distribution hemipelagic sediment. Hydrate Ridge lies within the gas hydrate stability field offshore central Oregon and during the last 15 years several studies have documented gas hydrate and cold seep carbonate occurrence

  18. Geophysical evidence for gas hydrates in the deep water of the South Caspian Basin, Azerbaijan

    E-Print Network [OSTI]

    Knapp, James Howard

    Geophysical evidence for gas hydrates in the deep water of the South Caspian Basin, Azerbaijan C) of this area, the presence of gas hydrates. Geophysical evidence for gas hydrates consists of a shallow (300, and is interpreted as the top of the gas hydrate layer. Similarly, a high-amplitude Rc

  19. Journal of Crystal Growth 243 (2002) 476489 Nucleation of gas hydrates

    E-Print Network [OSTI]

    Firoozabadi, Abbas

    2002-01-01T23:59:59.000Z

    Journal of Crystal Growth 243 (2002) 476­489 Nucleation of gas hydrates Dimo Kashchieva , Abbas of nucleation of one-component gas hydrates in aqueous solutions are analyzed. The size of the hydrate nucleus. Nucleation; B1. Gas hydrates 1. Introduction Nucleation is perhaps the most challenging step in understanding

  20. Characterization of in situ elastic properties of gas hydrate-bearing sediments on the Blake Ridge

    E-Print Network [OSTI]

    Guerin, Gilles

    17 Chapter 2: Characterization of in situ elastic properties of gas hydrate-bearing sediments acquired in gas-hydrate bearing sediments on the Blake Ridge to characterize the very distinct seismic with free gas. Between these two depths, gas hydrate and free gas seem to coexist. Within the Gas Hydrate

  1. Evidence from threedimensional seismic tomography for a substantial accumulation of gas hydrate in a fluidescape

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Evidence from threedimensional seismic tomography for a substantial accumulation of gas hydrate to be associated with the emplacement of hydrate, accompanying the invasion of the gas hydrate stability zone accumulation of gas hydrate in a fluidescape chimney in the Nyegga pockmark field, offshore Norway, J. Geophys

  2. Gas hydrate research in the Gulf of Mexico: Final report

    SciTech Connect (OSTI)

    Bennet, R.

    1988-05-01T23:59:59.000Z

    The high energy seismic sections on the continental slope showed no evidence of a Bottom Simulating Reflector (BSR), which would indicate the presence of gas hydrates. There was no indication of metastable hydrates in continental shelf or slope sediments outside of the conventionally accepted temperature and pressure environment. Tracing the path of migrating gas from the source is much more straight forward than intercepting gas being transported and tracing it back to the source. Our study of low and medium energy seismic methods has shown that they could identify migrating gas. We feel strongly that there are hydrate zones in the Gulf of Mexico that are decomposing; they build up pressure and periodically release the trapped hydrocarbon gases. The released gases migrate vertically and/or laterally to mix with other types of gas or to form discrete pockets. Some of this gas may be emitted from underwater seeps into the overlying water column where it could be identified by a geochemical survey. The ratio of isobutane to normal butane determined by the geochemical survey can be used to assess the probability of the hydrocarbons emanating from a hydrate source. (The more the ratio exceeds 1.0 the greater the probability that the gas could be from a hydrate source.) As no indications of a hydrate zone (e.g., a BSR) were located, we were not able to establish a geophysical signature for gas hydrates; but the records indicate there are large volumes of gas migrating up the continental slope, some of which may have originated from a decomposing hydrate zone or from gas trapped below the hydrate cap. 20 refs., 13 figs., 1 tab.

  3. WPMT (Fall 2009) Page 1 June 8, 2009 Wood Products Manufacturing Technology

    E-Print Network [OSTI]

    positions in wood products manufacturing, particularly for the hardwood cabinet and furniture industries to Lean Manufacturing (3) MET 14100 Materials I (4) Physics elective3 (3) STAT 30100 Elementary Sixth Semester (3) ECON 21000 Principles of Economics (3) FNR 31100 Wood Structure, Identification

  4. Supplying the nuclear arsenal: Production reactor technology, management, and policy, 1942--1992

    SciTech Connect (OSTI)

    Carlisle, R.P.; Zenzen, J.M.

    1994-01-01T23:59:59.000Z

    This book focuses on the lineage of America`s production reactors, those three at Hanford and their descendants, the reactors behind America`s nuclear weapons. The work will take only occasional sideways glances at the collateral lines of descent, the reactor cousins designed for experimental purposes, ship propulsion, and electric power generation. Over the decades from 1942 through 1992, fourteen American production reactors made enough plutonium to fuel a formidable arsenal of more than twenty thousand weapons. In the last years of that period, planners, nuclear engineers, and managers struggled over designs for the next generation of production reactors. The story of fourteen individual machines and of the planning effort to replace them might appear relatively narrow. Yet these machines lay at the heart of the nation`s nuclear weapons complex. The story of these machines is the story of arming the winning weapon, supplying the nuclear arms race. This book is intended to capture the history of the first fourteen production reactors, and associated design work, in the face of the end of the Cold War.

  5. Science and Technology Development to Integrate Energy Production and Greenhouse Gas Management

    SciTech Connect (OSTI)

    Pendergast, D.

    2004-10-03T23:59:59.000Z

    This paper reviews the carbon cycle from the point of view of past and present human influence. Potential future human input to the cycle through science and technology to manage atmospheric greenhouse gas are considered. The review suggests that humans will need to ingeniously exploit even more energy to integrate its use with control of atmospheric greenhouse gases. Continuing development and application of energy is essential if the development of human society is to be sustained through the coming centuries. The continuing development of nuclear energy seems an essential energy supply component.

  6. Hydrogen Storage Technologies: Long-Term Commercialization Approach with First Products First

    Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative Fuels Data Center Home Page on Google Bookmark EERE: Alternative Fuels DataDepartment of Energy Your Density Isn't YourTransport(Fact Sheet), GeothermalGridHYDROGEND D eReview |Panel HydrogenM M a aTechnologies

  7. Rapid Production of Methane Hydrates | netl.doe.gov

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    AFDC Printable Version Share this resource Send a link to EERE: Alternative Fuels Data Center Home Page to someone by E-mail Share EERE: Alternative Fuels Data Center Home Page on Facebook Tweet about EERE: Alternative Fuels Data Center Home Page on Twitter Bookmark EERE: Alternative1 First Use of Energy for All Purposes (Fuel and Nonfuel), 2002; Level:Energy: Grid Integration Redefining What's PossibleRadiation Protection Radiation ProtectionRaising funds for a cureEnergy Storage

  8. Examination of Hydrate Formation Methods: Trying to Create Representative Samples

    SciTech Connect (OSTI)

    Kneafsey, T.J.; Rees, E.V.L.; Nakagawa, S.; Kwon, T.-H.

    2011-04-01T23:59:59.000Z

    Forming representative gas hydrate-bearing laboratory samples is important so that the properties of these materials may be measured, while controlling the composition and other variables. Natural samples are rare, and have often experienced pressure and temperature changes that may affect the property to be measured [Waite et al., 2008]. Forming methane hydrate samples in the laboratory has been done a number of ways, each having advantages and disadvantages. The ice-to-hydrate method [Stern et al., 1996], contacts melting ice with methane at the appropriate pressure to form hydrate. The hydrate can then be crushed and mixed with mineral grains under controlled conditions, and then compacted to create laboratory samples of methane hydrate in a mineral medium. The hydrate in these samples will be part of the load-bearing frame of the medium. In the excess gas method [Handa and Stupin, 1992], water is distributed throughout a mineral medium (e.g. packed moist sand, drained sand, moistened silica gel, other porous media) and the mixture is brought to hydrate-stable conditions (chilled and pressurized with gas), allowing hydrate to form. This method typically produces grain-cementing hydrate from pendular water in sand [Waite et al., 2004]. In the dissolved gas method [Tohidi et al., 2002], water with sufficient dissolved guest molecules is brought to hydrate-stable conditions where hydrate forms. In the laboratory, this is can be done by pre-dissolving the gas of interest in water and then introducing it to the sample under the appropriate conditions. With this method, it is easier to form hydrate from more soluble gases such as carbon dioxide. It is thought that this method more closely simulates the way most natural gas hydrate has formed. Laboratory implementation, however, is difficult, and sample formation is prohibitively time consuming [Minagawa et al., 2005; Spangenberg and Kulenkampff, 2005]. In another version of this technique, a specified quantity of gas is placed in a sample, then the sample is flooded with water and cooled [Priest et al., 2009]. We have performed a number of tests in which hydrate was formed and the uniformity of the hydrate formation was examined. These tests have primarily used a variety of modifications of the excess gas method to make the hydrate, although we have also used a version of the excess water technique. Early on, we found difficulties in creating uniform samples with a particular sand/ initial water saturation combination (F-110 Sand, {approx} 35% initial water saturation). In many of our tests we selected this combination intentionally to determine whether we could use a method to make the samples uniform. The following methods were examined: Excess gas, Freeze/thaw/form, Freeze/pressurize/thaw, Excess gas followed by water saturation, Excess water, Sand and kaolinite, Use of a nucleation enhancer (SnoMax), and Use of salt in the water. Below, each method, the underlying hypothesis, and our results are briefly presented, followed by a brief conclusion. Many of the hypotheses investigated are not our own, but were presented to us. Much of the data presented is from x-ray CT scanning our samples. The x-ray CT scanner provides a three-dimensional density map of our samples. From this map and the physics that is occurring in our samples, we are able to gain an understanding of the spatial nature of the processes that occur, and attribute them to the locations where they occur.

  9. Quarterly Report: Microchannel-Assisted Nanomaterial Deposition Technology for Photovoltaic Material Production

    SciTech Connect (OSTI)

    Palo, Daniel R.

    2011-04-26T23:59:59.000Z

    Quarterly report to ITP for Nanomanufacturing program. Report covers FY11 Q2. The primary objective of this project is to develop a nanomanufacturing process which will reduce the manufacturing energy, environmental discharge, and production cost associated with current nano-scale thin-film photovoltaic (PV) manufacturing approaches. The secondary objective is to use a derivative of this nanomanufacturing process to enable greener, more efficient manufacturing of higher efficiency quantum dot-based photovoltaic cells now under development. The work is to develop and demonstrate a scalable (pilot) microreactor-assisted nanomaterial processing platform for the production, purification, functionalization, and solution deposition of nanomaterials for photovoltaic applications. The high level task duration is shown. Phase I consists of a pilot platform for Gen II PV films along with parallel efforts aimed at Gen III PV quantum dot materials. Status of each task is described.

  10. Fuel-Flexible Gasification-Combustion Technology for Production of H2 and Sequestration-Ready CO2

    SciTech Connect (OSTI)

    Parag Kulkarni; Jie Guan; Raul Subia; Zhe Cui; Jeff Manke; Arnaldo Frydman; Wei Wei; Roger Shisler; Raul Ayala; om McNulty; George Rizeq; Vladimir Zamansky; Kelly Fletcher

    2008-03-31T23:59:59.000Z

    In the near future, the nation will continue to rely on fossil fuels for electricity, transportation, and chemicals. It is necessary to improve both the process efficiency and environmental impact of fossil fuel utilization including greenhouse gas management. GE Global Research (GEGR) investigated an innovative fuel-flexible Unmixed Fuel Processor (UFP) technology with potential to produce H{sub 2}, power, and sequestration-ready CO{sub 2} from coal and other solid fuels. The UFP technology offers the long-term potential for reduced cost, increased process efficiency relative to conventional gasification and combustion systems, and near-zero pollutant emissions. GE was awarded a contract from U.S. DOE NETL to investigate and develop the UFP technology. Work started on the Phase I program in October 2000 and on the Phase II effort in April 2005. In the UFP technology, coal, water and air are simultaneously converted into (1) hydrogen rich stream that can be utilized in fuel cells or turbines, (2) CO{sub 2} rich stream for sequestration, and (3) high temperature/pressure vitiated air stream to produce electricity in a gas turbine expander. The process produces near-zero emissions with an estimated efficiency higher than Integrated Gasification Combined Cycle (IGCC) process with conventional CO{sub 2} separation. The Phase I R&D program established the chemical feasibility of the major reactions of the integrated UFP technology through lab-, bench- and pilot-scale testing. A risk analysis session was carried out at the end of Phase I effort to identify the major risks in the UFP technology and a plan was developed to mitigate these risks in the Phase II of the program. The Phase II effort focused on three high-risk areas: economics, lifetime of solids used in the UFP process, and product gas quality for turbines (or the impact of impurities in the coal on the overall system). The economic analysis included estimating the capital cost as well as the costs of hydrogen and electricity for a full-scale UFP plant. These costs were benchmarked with IGCC polygen plants with similar level of CO{sub 2} capture. Based on the promising economic analysis comparison results (performed with the help from Worley Parsons), GE recommended a 'Go' decision in April 2006 to continue the experimental investigation of the UFP technology to address the remaining risks i.e. solids lifetime and the impact of impurities in the coal on overall system. Solids attrition and lifetime risk was addressed via bench-scale experiments that monitor solids performance over time and by assessing materials interactions at operating conditions. The product gas under the third reactor (high-temperature vitiated air) operating conditions was evaluated to assess the concentration of particulates, pollutants and other impurities relative to the specifications required for gas turbine feed streams. During this investigation, agglomeration of solids used in the UFP process was identified as a serious risk that impacts the lifetime of the solids and in turn feasibility of the UFP technology. The main causes of the solids agglomeration were the combination of oxygen transfer material (OTM) reduction at temperatures {approx}1000 C and interaction between OTM and CO{sub 2} absorbing material (CAM) at high operating temperatures (>1200 C). At the end of phase II, in March 2008, GEGR recommended a 'No-go' decision for taking the UFP technology to the next level of development, i.e. development of a 3-5 MW prototype system, at this time. GEGR further recommended focused materials development research programs on improving the performance and lifetime of solids materials used in UFP or chemical looping technologies. The scale-up activities would be recommended only after mitigating the risks involved with the agglomeration and overall lifetime of the solids. This is the final report for the phase II of the DOE-funded Vision 21 program entitled 'Fuel-Flexible Gasification-Combustion Technology for Production of H{sub 2} and Sequestration-Ready CO{sub 2}' (DOE Award No.

  11. INCREASING HEAVY OIL RESERVES IN THE WILMINGTON OIL FIELD THROUGH ADVANCED RESERVOIR CHARACTERIZATION AND THERMAL PRODUCTION TECHNOLOGIES

    SciTech Connect (OSTI)

    Scott Hara

    2004-03-05T23:59:59.000Z

    The overall objective of this project is to increase heavy oil reserves in slope and basin clastic (SBC) reservoirs through the application of advanced reservoir characterization and thermal production technologies. The project involves improving thermal recovery techniques in the Tar Zone of Fault Blocks II-A and V (Tar II-A and Tar V) of the Wilmington Field in Los Angeles County, near Long Beach, California. A primary objective is to transfer technology which can be applied in other heavy oil formations of the Wilmington Field and other SBC reservoirs, including those under waterflood. The thermal recovery operations in the Tar II-A and Tar V have been relatively inefficient because of several producibility problems which are common in SBC reservoirs. Inadequate characterization of the heterogeneous turbidite sands, high permeability thief zones, low gravity oil, and nonuniform distribution of remaining oil have all contributed to poor sweep efficiency, high steam-oil ratios, and early steam breakthrough. Operational problems related to steam breakthrough, high reservoir pressure, and unconsolidated formation sands have caused premature well and downhole equipment failures. In aggregate, these reservoir and operational constraints have resulted in increased operating costs and decreased recoverable reserves. The advanced technologies to be applied include: (1) Develop three-dimensional (3-D) deterministic and stochastic geologic models. (2) Develop 3-D deterministic and stochastic thermal reservoir simulation models to aid in reservoir management and subsequent development work. (3) Develop computerized 3-D visualizations of the geologic and reservoir simulation models to aid in analysis. (4) Perform detailed study on the geochemical interactions between the steam and the formation rock and fluids. (5) Pilot steam injection and production via four new horizontal wells (2 producers and 2 injectors). (6) Hot water alternating steam (WAS) drive pilot in the existing steam drive area to improve thermal efficiency. (7) Installing an 2400 foot insulated, subsurface harbor channel crossing to supply steam to an island location. (8) Test a novel alkaline steam completion technique to control well sanding problems and fluid entry profiles. (9) Advanced reservoir management through computer-aided access to production and geologic data to integrate reservoir characterization, engineering, monitoring, and evaluation.

  12. Status of the technologies for the production of the Cherenkov Telescope Array (CTA) mirrors

    E-Print Network [OSTI]

    Pareschi, G; Baba, H; Bähr, J; Bonardi, A; Bonnoli, G; Brun, P; Canestrari, R; Chadwick, P; Chikawa, M; Carton, P -H; de Souza, V; Dipold, J; Doro, M; Durand, D; Dyrda, M; Förster, A; Garczarczyk, M; Giro, E; Glicenstein, J -F; Hanabata, Y; Hayashida, M; Hrabovski, M; Jeanney, C; Kagaya, M; Katagiri, H; Lessio, L; Mandat, D; Mariotti, M; Medina, C; Micha?owski, J; Micolon, P; Nakajima, D; Niemiec, J; Nozato, A; Palatka, M; Pech, M; Peyaud, B; Pühlhofer, G; Rataj, M; Rodeghiero, G; Rojas, G; Rousselle, J; Sakonaka, R; Schovanek, P; Seweryn, K; Schultz, C; Shu, S; Stinzing, F; Stodulski, M; Teshima, M; Travniczek, P; van Eldik, C; Vassiliev, V; Wi?niewski, ?; Wörnlein, A; Yoshida, T

    2013-01-01T23:59:59.000Z

    The Cherenkov Telescope Array (CTA) is the next generation very high-energy gamma-ray observatory, with at least 10 times higher sensitivity than current instruments. CTA will comprise several tens of Imaging Atmospheric Cherenkov Telescopes (IACTs) operated in array-mode and divided into three size classes: large, medium and small telescopes. The total reflective surface could be up to 10,000 m2 requiring unprecedented technological efforts. The properties of the reflector directly influence the telescope performance and thus constitute a fundamental ingredient to improve and maintain the sensitivity. The R&D status of lightweight, reliable and cost-effective mirror facets for the CTA telescope reflectors for the different classes of telescopes is reviewed in this paper.

  13. Simulation studies of slow dynamics of hydration water in lysozyme : hydration level dependence and comparison with experiment using new time domain analysis

    E-Print Network [OSTI]

    Kim, Chansoo, S.M. Massachusetts Institute of Technology

    2008-01-01T23:59:59.000Z

    A series of Molecular Dynamics (MD) simulations using the GROMACS® package has been performed in this thesis. It is used to mimic and simulate the hydration water in Lysozyme with three different hydration levels (h = 0.3, ...

  14. HEAT OF HYDRATION OF SALTSTONE MIXES-MEASUREMENT BY ISOTHERMAL CALORIMETRY

    SciTech Connect (OSTI)

    Harbour, J; Vickie Williams, V; Tommy Edwards, T

    2007-07-02T23:59:59.000Z

    This report provides initial results on the measurement of heat of hydration of Saltstone mixes using isothermal calorimetry. The results were obtained using a recently purchased TAM Air Model 3116 Isothermal Conduction Calorimeter. Heat of hydration is an important property of Saltstone mixes. Greater amounts of heat will increase the temperature of the curing mix in the vaults and limit the processing rate. The heat of hydration also reflects the extent of the hydraulic reactions that turn the fluid mixture into a ''stone like'' solid and consequently impacts performance properties such as permeability. Determining which factors control these reactions, as monitored by the heat of hydration, is an important goal of the variability study. Experiments with mixes of portland cement in water demonstrated that the heats measured by this technique over a seven day period match very well with the literature values of (1) seven day heats of hydration using the standard test method for heat of hydration of hydraulic cement, ASTM C 186-05 and (2) heats of hydration measured using isothermal calorimetry. The heats of hydration of portland cement or blast furnace slag in a Modular Caustic Side Solvent Extraction Unit (MCU) simulant revealed that if the cure temperature is maintained at 25 C, the amount of heat released over a seven day period is roughly 62% less than the heat released by portland cement in water. Furthermore, both the blast furnace slag and the portland cement were found to be equivalent in heat production over the seven day period in MCU. This equivalency is due to the activation of the slag by the greater than 1 Molar free hydroxide ion concentration in the simulant. Results using premix (a blend of 10% cement, 45% blast furnace slag, and 45% fly ash) in MCU, Deliquification, Dissolution and Adjustment (DDA) and Salt Waste Processing Facility (SWPF) simulants reveal that the fly ash had not significantly reacted (undergone hydration reactions) after seven days (most likely less than 5%). There were clear differences in the amount of heat released and the peak times of heat release for the three different simulants. It turns out that SWPF simulant mixes give off greater heat than does MCU and DDA simulant mixes. The temperature dependence of the heat of hydration was measured by carrying out these measurements at 25, 40 and 55 C. In general, the peak times shifted to shorter times as the isothermal temperature increased and the amount of heat released was independent of temperature for DDA and MCU but slightly higher at higher temperatures for SWPF. The goal of this study is to apply this technique to the measurement of the heat of hydration of mixes that will be made as part of the variability study. It is important to understand which variables will impact (and to what extent) the amount of heat generated and the peak times for the heat release. Those variables that can be controlled can then be tuned to adjust the heat of hydration as long as the other properties are still acceptable. The first application of heat of hydration measurements to the variability study was completed and the results presented in this report. These measurements were made using Phase VI mixes (SWPF simulants) following a statistical design that included variation in the compositional and operational variables. Variation in both the amount of heat released and the peak times for the heat release were observed. The measured ranges were 23 Joules per gram of premix for the heat release and 23 hours for the peak time of heat release at 25 C. Linear models with high R{sup 2} values and no statistical evidence for lack of fit were developed that relate the amount of heat release and the peak time for heat release for the Phase VI mixes to certain variables. The amount of heat released was a function of the aluminate and portland cement concentrations as well as the temperature of mixing. The peak time for heat release was a function of aluminate, portland cement and total nitrate plus nitrite concentrations. A comparison was made of the mea

  15. Drilling Through Gas Hydrates Formations: Managing Wellbore Stability Risks

    E-Print Network [OSTI]

    Khabibullin, Tagir R.

    2010-10-12T23:59:59.000Z

    As hydrocarbon exploration and development moves into deeper water and onshore arctic environments, it becomes increasingly important to quantify the drilling hazards posed by gas hydrates. To address these concerns, a 1D semi-analytical model...

  16. Carbon dioxide hydrate particles for ocean carbon sequestration

    E-Print Network [OSTI]

    Chow, A.C.

    This paper presents strategies for producing negatively buoyant CO[subscript 2] hydrate composite particles for ocean carbon sequestration. Our study is based on recent field observations showing that a continuous-jet ...

  17. Effectiveness of Alcohol Cosurfactants in Hydrate Antiagglomeration Minwei Sun,

    E-Print Network [OSTI]

    Firoozabadi, Abbas

    Firoozabadi*,, Reservoir Engineering Research Institute, 595 Lytton Ave. Suite B, Palo Alto, California 94301, especially in the deep sea, formation of gas hydrates may plug flowlines.1 There are significant safety

  18. Geotechnical characterization of sediments from Hydrate Ridge, Cascadia Continental Margin

    E-Print Network [OSTI]

    Tan, Brian B. (Brian Bautista), 1979-

    2004-01-01T23:59:59.000Z

    Eight whole core sediment samples were obtained from ODP Site 1244, Hydrate Ridge, Cascadia Continental Margin with the goal of understanding the stress history, consolidation behavior and strength characteristics of the ...

  19. An Integrated Study Method For Exploration Of Gas Hydrate Reservoirs...

    Open Energy Info (EERE)

    Method For Exploration Of Gas Hydrate Reservoirs In Marine Areas Jump to: navigation, search OpenEI Reference LibraryAdd to library Journal Article: An Integrated Study Method For...

  20. Continuing investigations for technology assessment of /sup 99/Mo production from LEU (low enriched Uranium) targets

    SciTech Connect (OSTI)

    Vandergrift, G.F.; Kwok, J.D.; Marshall, S.L.; Vissers, D.R.; Matos, J.E.

    1987-01-01T23:59:59.000Z

    Currently much of the world's supply of /sup 99m/Tc for medical purposes is produced from /sup 99/Mo derived from the fissioning of high enriched uranium (HEU). The need for /sup 99m/Tc is continuing to grow, especially in developing countries, where needs and national priorities call for internal production of /sup 99/Mo. This paper presents the results of our continuing studies on the effects of substituting low enriched Uranium (LEU) for HEU in targets for the production of fission product /sup 99/Mo. Improvements in the electrodeposition of thin films of uranium metal are reported. These improvements continue to increase the appeal for the substitution of LEU metal for HEU oxide films in cylindrical targets. The process is effective for targets fabricated from stainless steel or hastaloy. A cost estimate for setting up the necessary equipment to electrodeposit uranium metal on cylindrical targets is reported. Further investigations on the effect of LEU substitution on processing of these targets are also reported. Substitution of uranium silicides for the uranium-aluminum alloy or uranium aluminide dispersed fuel used in other current target designs will allow the substitution of LEU for HEU in these targets with equivalent /sup 99/Mo-yield per target and no change in target geometries. However, this substitution will require modifications in current processing steps due to (1) the insolubility of uranium silicides in alkaline solutions and (2) the presence of significant quantities of silicate in solution. Results to date suggest that both concerns can be handled and that substitution of LEU for HEU can be achieved.

  1. Advanced Production Surface Preparation Technology Development for Ultra-High Pressure Diesel Injection

    SciTech Connect (OSTI)

    Grant, Marion B.

    2012-04-30T23:59:59.000Z

    In 2007, An Ultra High Injection Pressure (UHIP) fueling method has been demonstrated by Caterpillar Fuel Systems - Product Development, demonstrating ability to deliver U.S. Environment Protection Agency (EPA) Tier 4 Final diesel engine emission performance with greatly reduced emissions handling components on the engine, such as without NOx reduction after-treatment and with only a through-flow 50% effective diesel particulate trap (DPT). They have shown this capability using multiple multi-cylinder engine tests of an Ultra High Pressure Common Rail (UHPCR) fuel system with higher than traditional levels of CEGR and an advanced injector nozzle design. The system delivered better atomization of the fuel, for more complete burn, to greatly reduce diesel particulates, while CEGR or high efficiency NOx reduction after-treatment handles the NOx. With the reduced back pressure of a traditional DPT, and with the more complete fuel burn, the system reduced levels of fuel consumption by 2.4% for similar delivery of torque and horsepower over the best Tier 4 Interim levels of fuel consumption in the diesel power industry. The challenge is to manufacture the components in high-volume production that can withstand the required higher pressure injection. Production processes must be developed to increase the toughness of the injector steel to withstand the UHIP pulsations and generate near perfect form and finish in the sub-millimeter size geometries within the injector. This project resulted in two developments in 2011. The first development was a process and a machine specification by which a high target of compressive residual stress (CRS) can be consistently imparted to key surfaces of the fuel system to increase the toughness of the steel, and a demonstration of the feasibility of further refinement of the process for use in volume production. The second development was the demonstration of the feasibility of a process for imparting near perfect, durable geometry to these same feature surfaces to withstand the pulsating UHIP diesel injection without fatigue failure, through the expected life of the fuel system's components (10,000 hours for the pump and common rail, 5000 hours for the injector). The potential to Caterpillar of this fueling approach and the overall emissions reduction system is the cost savings of the fuel, the cost savings of not requiring a full emissions module and other emissions hardware, and the enabling of the use of biodiesel fuel due to the reduced dependency on after-treatment. A proprietary production CRS generating process was developed to treat the interior of the sac-type injector nozzle tip region (particularly for the sac region). Ninety-five tips passed ultra high pulsed pressure fatigue testing with no failures assignable to treated surfaces or materials. It was determined that the CRS impartation method does not weaken the tip internal seat area. Caterpillar Fuel Systems - Product Development accepts that the CRS method initial production technical readiness level has been established. A method to gage CRS levels in production was not yet accomplished, but it is believed that monitoring process parameters call be used to guarantee quality. A precision profiling process for injector seat and sac regions has been shown to be promising but not yet fully confirmed. It was demonstrated that this precision profiling process can achieve form and geometry to well under an aggressively small micron peak-to-valley and that there are no surface flaws that approach an even tighter micron peak-to-valley tolerance. It is planned to purchase machines to further develop and move the process towards production. The system is targeted towards the high-power diesel electric power generators and high-power diesel marine power generators, with displacement from 20 liters to 80 liters and with power from 800 brake horsepower (BHP) to 3200BHP (0.6 megawatts to 2.4 megawatts). However, with market adoption, this system has the potential to meet EPA exhaust standards for all diesel engines nine liters and up, or 300B

  2. Oil and Gas Science and Technology, 2009, 64(5), 629-636, doi: 10.2516/ogst/2009042 DDDiiissscccuuussssssiiiooonnn ooofff aaagggggglllooommmeeerrraaatttiiiooonnn mmmeeeccchhhaaannniiisssmmmsss bbbeeetttwwweeeeeennn hhhyyydddrrraaattteee

    E-Print Network [OSTI]

    Paris-Sud XI, Université de

    Oil and Gas Science and Technology, 2009, 64(5), 629-636, doi: 10.2516/ogst/2009042 1. KKeeyywwoorrddss:: gas hydrate formation ; water/oil emulsions ; hydrate slurry ; agglomeration ; Population@emse.fr hal-00480033,version1-3May2010 Author manuscript, published in "Oil & Gas Science and Technology 64, 5

  3. FUEL-FLEXIBLE GASIFICATION-COMBUSTION TECHNOLOGY FOR PRODUCTION OF H2 AND SEQUESTRATION-READY CO2

    SciTech Connect (OSTI)

    George Rizeq; Janice West; Arnaldo Frydman; Raul Subia; Vladimir Zamansky; Hana Loreth; Lubor Stonawski; Tomasz Wiltowski; Edwin Hippo; Shashi Lalvani

    2003-01-01T23:59:59.000Z

    It is expected that in the 21st century the Nation will continue to rely on fossil fuels for electricity, transportation, and chemicals. It will be necessary to improve both the process efficiency and environmental impact performance of fossil fuel utilization. GE Energy and Environmental Research Corporation (GE EER) has developed an innovative fuel-flexible Unmixed Fuel Processor (UFP) technology to produce H{sub 2}, power, and sequestration-ready CO{sub 2} from coal and other solid fuels. The UFP module offers the potential for reduced cost, increased process efficiency relative to conventional gasification and combustion systems, and near-zero pollutant emissions including NO{sub x}. GE EER was awarded a Vision 21 program from U.S. DOE NETL to develop the UFP technology. Work on this Phase I program started on October 1, 2000. The project team includes GE EER, California Energy Commission, Southern Illinois University at Carbondale, and T. R. Miles, Technical Consultants, Inc. In the UFP technology, coal/opportunity fuels and air are simultaneously converted into separate streams of (1) pure hydrogen that can be utilized in fuel cells, (2) sequestration-ready CO{sub 2}, and (3) high temperature/pressure oxygen-depleted air to produce electricity in a gas turbine. The process produces near-zero emissions and, based on process modeling work, has an estimated process efficiency of 68%, based on electrical and H{sub 2} energy outputs relative to the higher heating value of coal, and an estimated equivalent electrical efficiency of 60%. The Phase I R&D program will determine the operating conditions that maximize separation of CO{sub 2} and pollutants from the vent gas, while simultaneously maximizing coal conversion efficiency and hydrogen production. The program integrates lab-, bench- and pilot-scale studies to demonstrate the UFP technology. This is the ninth quarterly technical progress report for the Vision 21 UFP program supported by U.S. DOE NETL (Contract No. DE-FC26-00FT40974). This report summarizes program accomplishments for the period starting October 1, 2002 and ending December 31, 2002. The report includes an introduction summarizing the UFP technology, main program tasks, and program objectives; it also provides a summary of program activities and accomplishments covering progress in tasks including lab- and bench-scale experimental testing, pilot-scale design and assembly, and program management.

  4. A Domain Decomposition Approach for Large-Scale Simulations of Flow Processes in Hydrate-Bearing Geologic Media

    SciTech Connect (OSTI)

    Zhang, Keni; Moridis, G.J.; Wu, Y.-S.; Pruess, K.

    2008-07-01T23:59:59.000Z

    Simulation of the system behavior of hydrate-bearing geologic media involves solving fully coupled mass- and heat-balance equations. In this study, we develop a domain decomposition approach for large-scale gas hydrate simulations with coarse-granularity parallel computation. This approach partitions a simulation domain into small subdomains. The full model domain, consisting of discrete subdomains, is still simulated simultaneously by using multiple processes/processors. Each processor is dedicated to following tasks of the partitioned subdomain: updating thermophysical properties, assembling mass- and energy-balance equations, solving linear equation systems, and performing various other local computations. The linearized equation systems are solved in parallel with a parallel linear solver, using an efficient interprocess communication scheme. This new domain decomposition approach has been implemented into the TOUGH+HYDRATE code and has demonstrated excellent speedup and good scalability. In this paper, we will demonstrate applications for the new approach in simulating field-scale models for gas production from gas-hydrate deposits.

  5. The rate of isothermal hydration of polyperfluorosulfonic acid membranes

    E-Print Network [OSTI]

    Van Nguyen, Trung; Vanderborgh, N.

    1998-05-27T23:59:59.000Z

    The Rate of Isothermal Hydration of Polyperfluorosulfonic Acid Membranes by Trung Van Nguyen * Department of Chemical and Petroleum Engineering 4006 Learned Hall The University of Kansas Lawrence, Kansas 66045-2223 and Nicholas... conditions for the three phases of a typical polymer hydration dynamic experiment. Measurements were made using a TA3000 Mettler thermal analysis system. Nitrogen was used as the carrier gas along with controlled quantities of water vapor that were...

  6. Predicted geoacoustic properties of gas hydrate saturated marine sediments

    E-Print Network [OSTI]

    Curtis, William Robert

    1992-01-01T23:59:59.000Z

    PREDICTED GEOACOUSTIC PROPERTIES OF GAS HYDRATE SATURATED MAR&K SEDIMENTS A Thesis by WILLIAM ROBERT CURTIS JR. Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment of the requirements for the degree... of MASTER OF SCIENCE May 1992 Major Subject: Oceanography PREDICTED GEOACOUSTIC PROPERTIES OF GAS HYDRATE SATURATED MARINE SEDIMENTS A Thesis by WILLIAM ROBERT CURTIS JR. Approved as to style and content by; A brey L. Anderson (Chair of Committee...

  7. Examination of core samples from the Mount Elbert Gas Hydrate Stratigraphic Test Well, Alaska North Slope: Effects of retrieval and preservation

    E-Print Network [OSTI]

    Collett, T.J. Kneafsey, T.J., H. Liu, W. Winters, R. Boswell, R. Hunter, and T.S.

    2012-01-01T23:59:59.000Z

    and handling of natural gas hydrate. GSC Bulletin, 544: 263-naturally occurring gas hydrates: the structures of methanefrom the Mount Elbert Gas Hydrate Stratigraphic Test Well,

  8. Analysis of core samples from the BPXA-DOE-USGS Mount Elbert gas hydrate stratigraphic test well: Insights into core disturbance and handling

    E-Print Network [OSTI]

    Kneafsey, Timothy J.

    2010-01-01T23:59:59.000Z

    and handling of natural gas hydrate. GSC Bulletin, 544: 263-naturally occurring gas hydrates: the structures of methaneDOE-USGS Mount Elbert gas hydrate stratigraphic test well:

  9. Production of ethanol from refinery waste gases. Phase 2, technology development, annual report

    SciTech Connect (OSTI)

    Arora, D.; Basu, R.; Phillips, J.R.; Wikstrom, C.V.; Clausen, E.C.; Gaddy, J.L.

    1995-07-01T23:59:59.000Z

    Oil refineries discharge large volumes of H{sub 2}, CO, and CO{sub 2} from cracking, coking, and hydrotreating operations. This program seeks to develop a biological process for converting these waste gases into ethanol, which can be blended with gasoline to reduce emissions. Production of ethanol from all 194 US refineries would save 450 billion BTU annually, would reduce crude oil imports by 110 million barrels/year and emissions by 19 million tons/year. Phase II efforts has yielded at least 3 cultures (Clostridium ljungdahlii, Isolate O-52, Isolate C-01) which are able to produce commercially viable concentrations of ethanol from CO, CO{sub 2}, and H{sub 2} in petroleum waste gas. Single continuous stirred tank reactor studies have shown that 15-20 g/L of ethanol can be produced, with less than 5 g/L acetic acid byproduct. Culture and reactor optimization in Phase III should yield even higher ethanol concentrations and minimal acetic acid. Product recovery studies showed that ethanol is best recovered in a multi-step process involving solvent extraction/distillation to azeotrope/azeotropic distillation or pervaporation, or direct distillation to the azeotrope/azeotropic distillation or pervaporation. Projections show that the ethanol facility for a typical refinery would require an investment of about $30 million, which would be returned in less than 2 years.

  10. Enhanced Wellbore Stabilization and Reservoir Productivity with Aphron Drilling Fluid Technology

    SciTech Connect (OSTI)

    Fred Growcock

    2004-03-31T23:59:59.000Z

    During this second Quarter of the Project, the first four tasks of Phase I--all focusing on the behavior of aphrons--were continued: (a) Aphron Visualization--evaluate and utilize various methods of monitoring and measuring aphron size distribution at elevated pressure; (b) Fluid Density--investigate the effects of pressure, temperature and chemical composition on the survivability of aphrons; (c) Aphron Air Diffusivity--determine the rate of loss of air from aphrons during pressurization; and (d) Pressure Transmissibility--determine whether aphron bridges created in fractures and pore throats reduce fracture propagation. The project team expanded the laboratory facilities and purchased a high-pressure system to measure bubble size distribution, a dissolved oxygen (DO) probe and computers for data acquisition. Although MASI Technologies LLC is not explicitly ISO-certified, all procedures are being documented in a manner commensurate with ISO 9001 certification, including equipment inventory and calibration, data gathering and reporting, chemical inventory and supplier data base, waste management procedures and emergency response plan. Several opportunities presented themselves to share the latest aphron drilling fluid technology with potential clients, including presentation of papers and working exhibit booths at the IADC/SPE Drilling Conference and the SPE Coiled Tubing Conference & Exhibition. In addition, a brief trip to the Formation Damage Symposium resulted in contacts for possible collaboration with ActiSystems, the University of Alberta and TUDRP/ACTS at the University of Tulsa. Preliminary results indicate that the Aphron Visualization and Pressure Transmissibility tasks should be completed on time. Although the Aphron Air Diffusivity task has been impeded by the lack of a suitable DO probe, it is hoped to be completed on time, too. The Fluid Density task, on the other hand, has had significant delays caused by faulty equipment and will likely require an additional month of work. Meanwhile, an assessment of potential methodologies for the Aphron Hydrophobicity project has been initiated and is now focused on measuring wettability of the aphron surface rather than interfacial tension.

  11. Painting a Picture of Gas Hydrate Distribution with Thermal Images

    SciTech Connect (OSTI)

    Weinberger, Jill L.; Brown, Kevin M.; Long, Philip E.

    2005-02-25T23:59:59.000Z

    Large uncertainties about the energy resource potential and role in global climate change of gas hydrates result from uncertainty about how much hydrate is contained in marine sediments. During Leg 204 of the Ocean Drilling Program (ODP) to the accretionary complex of the Cascadia subduction zone, the entire gas hydrate stability zone was sampled in contrasting geological settings defined by a 3D seismic survey. By integrating results from different methods, including several new techniques developed for Leg 204, we overcome the problem of spatial under-sampling inherent in robust methods traditionally used for estimating the hydrate content of cores and obtain a high-resolution, quantitative estimate of the total amount and spatial variability of gas hydrate in this structural system. We conclude that high gas hydrate content (30-40% of pore space of 20-26% of total volume) is restricted to the upper tens of meters below the seafloor near the summit of the structure, where vigorous fluid venting occurs.

  12. Premium Fuel Production From Mining and Timber Waste Using Advanced Separation and Pelletizing Technologies

    SciTech Connect (OSTI)

    Honaker, R. Q.; Taulbee, D.; Parekh, B. K.; Tao, D.

    2005-12-05T23:59:59.000Z

    The Commonwealth of Kentucky is one of the leading states in the production of both coal and timber. As a result of mining and processing coal, an estimated 3 million tons of fine coal are disposed annually to waste-slurry impoundments with an additional 500 million tons stored at a number of disposal sites around the state due to past practices. Likewise, the Kentucky timber industry discards nearly 35,000 tons of sawdust on the production site due to unfavorable economics of transporting the material to industrial boilers for use as a fuel. With an average heating value of 6,700 Btu/lb, the monetary value of the energy disposed in the form of sawdust is approximately $490,000 annually. Since the two industries are typically in close proximity, one promising avenue is to selectively recover and dewater the fine-coal particles and then briquette them with sawdust to produce a high-value fuel. The benefits are i) a premium fuel product that is low in moisture and can be handled, transported, and utilized in existing infrastructure, thereby avoiding significant additional capital investment and ii) a reduction in the amount of fine-waste material produced by the two industries that must now be disposed at a significant financial and environmental price. As such, the goal of this project was to evaluate the feasibility of producing a premium fuel with a heating value greater than 10,000 Btu/lb from waste materials generated by the coal and timber industries. Laboratory and pilot-scale testing of the briquetting process indicated that the goal was successfully achieved. Low-ash briquettes containing 5% to 10% sawdust were produced with energy values that were well in excess of 12,000 Btu/lb. A major economic hurdle associated with commercially briquetting coal is binder cost. Approximately fifty binder formulations, both with and without lime, were subjected to an extensive laboratory evaluation to assess their relative technical and economical effectiveness as binding agents for the briquetting of 90% coal and 10% sawdust blends. Guar gum, wheat starch, and a multi-component formulation were identified as most cost-effective for the production of briquettes targeted for the pulverized-coal market with costs being around $8 per ton of the coal-sawdust blend. REAX/lime and a second multi-component formulation were identified as the most cost-effective for the production of briquettes targeted for the stoker-coal market. Various sources of sawdust generated from different wood types were also investigated to determine their chemical properties and to evaluate their relative performance when briquetted with clean coal to form a premium fuel. The highest heating values, approaching 7,000 Btu/lb, were obtained from oak. Sawdusts from higher-density, red oak, white oak, hickory, and beech trees provided higher quality briquettes relative to their lower-density counterparts. In addition to sawdust type, a number of other parameters were evaluated to characterize their impact on briquette properties. The parameters that exhibited the greatest impact on briquette performance were binder concentration; sawdust concentration and particle size; cure temperature; and ash content. Parameters that had the least impact on briquette properties, at least over the ranges studied, were moisture content, briquetting force, and briquetting dwell time. The continuous production of briquettes from a blend of coal and sawdust was evaluated using a 200 lbs/hr Komarek Model B-100 briquetter. The heating values of briquettes produced by the unit exceeded the goal of the project by a large margin. A significant observation was the role of feed moisture on the stability of the mass flow rate through the briquetter and on briquette strength. Excessive feed moisture levels caused inconsistent or stoppage of material flow through the feed hopper and resulted in the production of variable-quality briquettes. Obviously, the limit on feed moisture content has a significant impact on the economics of coal-sawdust briquetting since it will ultimately dictate dew

  13. Final technical report: Commercialization of the Biofine technology for levulinic acid production from paper sludge

    SciTech Connect (OSTI)

    Fitzpatrick, Stephen W.

    2002-04-23T23:59:59.000Z

    This project involved a three-year program managed by BioMetics, Inc. (Waltham, MA) to demonstrate the commercial feasibility of Biofine thermochemical process technology for conversion of cellulose-containing wastes or renewable materials into levulinic acid, a versatile platform chemical. The program, commencing in October 1995, involved the design, procurement, construction and operation of a plant utilizing the Biofine process to convert 1 dry ton per day of paper sludge waste. The plant was successfully designed, constructed, and commissioned in 1997. It was operated for a period of one year on paper sludge from a variety of source paper mills to collect data to verify the design for a commercial scale plant. Operational results were obtained for four different feedstock varieties. Stable, continuous operation was achieved for two of the feedstocks. Continuous operation of the plant at demonstration scale provided the opportunity for process optimization, development of operational protocols, operator training and identification of suitable materials of construction for scale up to commercial operation . Separated fiber from municipal waster was also successfully processed. The project team consisted of BioMetics Inc., Great Lakes Chemical Corporation (West Lafayette, IN), and New York State Energy Research and Development Authority (Albany, NY).

  14. In-Situ Sampling and Characterization of Naturally Occurring Marine Methane Hydrate Using the D/V JOIDES Resolution

    SciTech Connect (OSTI)

    Frank R. Rack

    2006-09-20T23:59:59.000Z

    Cooperative Agreement DE-FC26-01NT41329 between Joint Oceanographic Institutions and DOE-NETL was divided into two phases based on successive proposals and negotiated statements of work pertaining to activities to sample and characterize methane hydrates on ODP Leg 204 (Phase 1) and on IODP Expedition 311 (Phase 2). The Phase 1 Final Report was submitted to DOE-NETL in April 2004. This report is the Phase 2 Final Report to DOE-NETL. The primary objectives of Phase 2 were to sample and characterize methane hydrates using the systems and capabilities of the D/V JOIDES Resolution during IODP Expedition 311, to enable scientists the opportunity to establish the mass and distribution of naturally occurring gas and gas hydrate at all relevant spatial and temporal scales, and to contribute to the DOE methane hydrate research and development effort. The goal of the work was to provide expanded measurement capabilities on the JOIDES Resolution for a dedicated hydrate cruise to the Cascadia continental margin off Vancouver Island, British Columbia, Canada (IODP Expedition 311) so that hydrate deposits in this region would be well characterized and technology development continued for hydrate research. IODP Expedition 311 shipboard activities on the JOIDES Resolution began on August 28 and were concluded on October 28, 2005. The statement of work for this project included three primary tasks: (1) research management oversight, provided by JOI; (2) mobilization, deployment and demobilization of pressure coring and core logging systems, through a subcontract with Geotek Ltd.; and, (3) mobilization, deployment and demobilization of a refrigerated container van that will be used for degassing of the Pressure Core Sampler and density logging of these pressure cores, through a subcontract with the Texas A&M Research Foundation (TAMRF). Additional small tasks that arose during the course of the research were included under these three primary tasks in consultation with the DOE-NETL Program Manager. All tasks outlined in the original statement of work were accomplished except for the deployment and use of the X-ray CT system under Subtask 2-2. This reduction in scope provided resources that were applied to other activities to support the overall project. Post-expedition analysis of results and report writing will continue beyond this reporting period, however, all field deployments associated with this project have been successfully concluded as of this writing.

  15. Ab initio investigation of the first hydration shell of protonated glycine

    SciTech Connect (OSTI)

    Wei, Zhichao; Chen, Dong, E-mail: dongchen@henu.edu.cn, E-mail: boliu@henu.edu.cn; Zhao, Huiling; Li, Yinli; Zhu, Jichun; Liu, Bo, E-mail: dongchen@henu.edu.cn, E-mail: boliu@henu.edu.cn [Institute of Photo-Biophysics, Physics and Electronics Department, Henan University, 475004 Kaifeng (China)] [Institute of Photo-Biophysics, Physics and Electronics Department, Henan University, 475004 Kaifeng (China)

    2014-02-28T23:59:59.000Z

    The first hydration shell of the protonated glycine is built up using Monte Carlo multiple minimum conformational search analysis with the MMFFs force field. The potential energy surfaces of the protonated glycine and its hydration complexes with up to eight water molecules have been scanned and the energy-minimized structures are predicted using the ab initio calculations. First, three favorable structures of protonated glycine were determined, and the micro-hydration processes showed that water can significantly stabilize the unstable conformers, and then their first hydration shells were established. Finally, we found that seven water molecules are required to fully hydrate the first hydration shell for the most stable conformer of protonated glycine. In order to analyse the hydration process, the dominant hydration sites located around the ammonium and carboxyl groups are studied carefully and systemically. The results indicate that, water molecules hydrate the protonated glycine in an alternative dynamic hydration process which is driven by the competition between different hydration sites. The first three water molecules are strongly attached by the ammonium group, while only the fourth water molecule is attached by the carboxyl group in the ultimate first hydration shell of the protonated glycine. In addition, the first hydration shell model has predicted most identical structures and a reasonable accord in hydration energy and vibrational frequencies of the most stable conformer with the conductor-like polarizable continuum model.

  16. Pressure-induced Hydration in Zeolite Tetranatrolite

    SciTech Connect (OSTI)

    Lee,Y.; Hriljac, J.; Parise, J.; Vogt, T.

    2006-01-01T23:59:59.000Z

    The tetranatrolite-paranatrolite transformation has remained a key problem in understanding the paragenesis of zeolites in the natrolite family. It is accepted that when paranatrolite, approximate formula Na{sub 16-x}Ca{sub x}Al{sub 16+x}Si{sub 24-x}O{sub 80}{center_dot}24H{sub 2}O, is removed from an aqueous environment and exposed to the atmosphere, it loses water and transforms to tetranatrolite, Na{sub 16-x}Ca{sub x}Al{sub 16+x}Si{sub 24-x}O{sub 80}{center_dot}nH{sub 2}O (n {le} 24). Here we show that this transformation is not only reversible, but that tetranatrolite exhibits two sequential pressure-induced hydrations leading first to paranatrolite and then to a superhydrated tetranatrolite above 0.2 and 3.0 GPa, respectively. We have previously reported similar behavior for the corresponding system with an ordered Si/Al distribution, i.e., natrolite itself, however the ordered version of paranatrolite exists over a much smaller pressure range. The pressure-induced transformations of natrolite and tetranatrolite thus further supports the supposition that paranatrolite is a distinct mineral species, with a pressure-stability field dependent upon composition.

  17. X-ray CT Observations of Methane Hydrate Distribution Changes over Time in a Natural Sediment Core from the BPX-DOE-USGS Mount Elbert Gas Hydrate Stratigraphic Test Well

    E-Print Network [OSTI]

    Kneafsey, T.J.

    2012-01-01T23:59:59.000Z

    and Englezos, P. , 2009. Gas hydrate formation in a variableDOE-USGS Mount Elbert Gas Hydrate Stratigraphic Test WellFormation of natural gas hydrates in marine sediments. 1.

  18. Geology, reservoir engineering and methane hydrate potential of the Walakpa Gas Field, North Slope, Alaska. Final report

    SciTech Connect (OSTI)

    Glenn, R.K.; Allen, W.W.

    1992-12-01T23:59:59.000Z

    The Walakpa Gas Field, located near the city of Barrow on Alaska`s North Slope, has been proven to be methane-bearing at depths of 2000--2550 feet below sea level. The producing formation is a laterally continuous, south-dipping, Lower Cretaceous shelf sandstone. The updip extent of the reservoir has not been determined by drilling, but probably extends to at least 1900 feet below sea level. Reservoir temperatures in the updip portion of the reservoir may be low enough to allow the presence of in situ methane hydrates. Reservoir net pay however, decreases to the north. Depths to the base of permafrost in the area average 940 feet. Drilling techniques and production configuration in the Walakpa field were designed to minimize formation damage to the reservoir sandstone and to eliminate methane hydrates formed during production. Drilling development of the Walakpa field was a sequential updip and lateral stepout from a previously drilled, structurally lower confirmation well. Reservoir temperature, pressure, and gas chemistry data from the development wells confirm that they have been drilled in the free-methane portion of the reservoir. Future studies in the Walakpa field are planned to determine whether or not a component of the methane production is due to the dissociation of updip in situ hydrates.

  19. Dynamics of lysozyme and its hydration water under electric field

    E-Print Network [OSTI]

    P. M. Favi; Q. Zhang; H. O'Neill; E. Mamontov; S. O. Diallo

    2013-12-06T23:59:59.000Z

    The effects of static electric field on the dynamics of lysozyme and its hydration water have been investigated by means of incoherent quasi-elastic neutron scattering (QENS). Measurements were performed on lysozyme samples, hydrated respectively with heavy water (D2O) to capture the protein dynamics, and with light water (H2O), to probe the dynamics of the hydration shell, in the temperature range from 210 $hydration fraction in both cases was about $\\sim$ 0.38 gram of water per gram of dry protein. The field strengths investigated were respectively 0 kV/mm and 2 kV/mm (2 10$^6$ V/m) for the protein hydrated with D2O and 0 kV and 1 kV/mm for the H2O hydrated counterpart. While the overall internal protons dynamics of the protein appears to be unaffected by the application of electric field up to 2 kV/mm, likely due to the stronger intra-molecular interactions, there is also no appreciable quantitative enhancement of the diffusive dynamics of the hydration water, as would be anticipated based on our recent observations in water confined in silica pores under field values of 2.5 kV/mm. This may be due to the difference in surface interactions between water and the two adsorption hosts (silica and protein), or to the existence of a critical threshold field value Ec $\\sim$ 2-3 kV/mm for increased molecular diffusion, for which electrical breakdown is a limitation for our sample.

  20. Product development practices that matter

    E-Print Network [OSTI]

    Gupta, Nisheeth

    2010-01-01T23:59:59.000Z

    Product Development consists of activities to transforms a market opportunity and technological innovation into successful products. Several waves of improvements in technological innovation and product development have ...

  1. Green Purchasing & Green Technology

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Purchasing & Technology Goals 6 & 7: Green Purchasing & Green Technology Our goal is to purchase and use environmentally sustainable products whenever possible and to implement...

  2. Phase Equilibria Studies in Water-Methane System: Structural Memory-Effect of Water On Hydrate Re-Formation

    E-Print Network [OSTI]

    Kim, Brice Yoonshik

    2014-12-08T23:59:59.000Z

    Naturally-occurring hydrates are promising resources. The potential value of gas accumulation in naturally-occurring gas hydrates can exceed 16 equivalent trillion tons of oil. There are many accurate findings on properties of gas hydrates...

  3. Application of the Split Hopkinson Resonant Bar Test for Seismic Property Characterization of Hydrate-bearing Sand Undergoing Water Saturation

    E-Print Network [OSTI]

    Nakagawa, S.

    2012-01-01T23:59:59.000Z

    E.V.L. 2009. Methane Gas Hydrate Morphology and its EffectGEO-SEQ Program and Gas Hydrate Program, through theInternational Conference on Gas Hydrates , Yokohama, 856–

  4. A Domain Decomposition Approach for Large-Scale Simulations of Flow Processes in Hydrate-Bearing Geologic Media

    E-Print Network [OSTI]

    Zhang, Keni

    2009-01-01T23:59:59.000Z

    In this deposit, water, gas, and hydrate are initially atwhen exhaustion of the free gas and hydrate resources in theAdvances in the Study of Gas Hydrates, C. Taylor and J.

  5. Methane Hydrate Field Program: Development of a Scientific Plan for a Methane Hydrate-Focused Marine Drilling, Logging and Coring Program

    SciTech Connect (OSTI)

    Collett, Tim; Bahk, Jang-Jun; Frye, Matt; Goldberg, Dave; Husebo, Jarle; Koh, Carolyn; Malone, Mitch; Shipp, Craig; Torres, Marta; Myers, Greg; Divins, David; Morell, Margo

    2013-11-30T23:59:59.000Z

    This topical report represents a pathway toward better understanding of the impact of marine methane hydrates on safety and seafloor stability and future collection of data that can be used by scientists, engineers, managers and planners to study climate change and to assess the feasibility of marine methane hydrate as a potential future energy resource. Our understanding of the occurrence, distribution and characteristics of marine methane hydrates is incomplete; therefore, research must continue to expand if methane hydrates are to be used as a future energy source. Exploring basins with methane hydrates has been occurring for over 30 years, but these e?orts have been episodic in nature. To further our understanding, these e?orts must be more regular and employ new techniques to capture more data. This plan identifies incomplete areas of methane hydrate research and o?ers solutions by systematically reviewing known methane hydrate “Science Challenges” and linking them with “Technical Challenges” and potential field program locations.

  6. Production

    Broader source: Energy.gov [DOE]

    Algae production R&D focuses on exploring resource use and availability, algal biomass development and improvements, characterizing algal biomass components, and the ecology and engineering of...

  7. Hydration water dynamics and instigation of protein structuralrelaxation

    SciTech Connect (OSTI)

    Russo, Daniela; Hura, Greg; Head-Gordon, Teresa

    2003-09-01T23:59:59.000Z

    Until a critical hydration level is reached, proteins do not function. This critical level of hydration is analogous to a similar lack of protein function observed for temperatures below a dynamical temperature range of 180-220K that also is connected to the dynamics of protein surface water. Restoration of some enzymatic activity is observed in partially hydrated protein powders, sometimes corresponding to less than a single hydration layer on the protein surface, which indicates that the dynamical and structural properties of the surface water is intimately connected to protein stability and function. Many elegant studies using both experiment and simulation have contributed important information about protein hydration structure and timescales. The molecular mechanism of the solvent motion that is required to instigate the protein structural relaxation above a critical hydration level or transition temperature has yet to be determined. In this work we use experimental quasi-elastic neutron scattering (QENS) and molecular dynamics simulation to investigate hydration water dynamics near a greatly simplified protein system. We consider the hydration water dynamics near the completely deuterated N-acetyl-leucine-methylamide (NALMA) solute, a hydrophobic amino acid side chain attached to a polar blocked polypeptide backbone, as a function of concentration between 0.5M-2.0M under ambient conditions. We note that roughly 50-60% of a folded protein's surface is equally distributed between hydrophobic and hydrophilic domains, domains whose lengths are on the order of a few water diameters, that justify our study of hydration dynamics of this simple model protein system. The QENS experiment was performed at the NIST Center for Neutron Research, using the disk chopper time of flight spectrometer (DCS). In order to separate the translational and rotational components in the spectra, two sets of experiments were carried out using different incident neutron wavelengths of 7.5{angstrom} and 5.5{angstrom} to give two different time resolutions. All the spectra have been measure at room temperature. The spectra were corrected for the sample holder contribution and normalized using the vanadium standard. The resulting data were analyzed with DAVE programs (http://www.ncnr.nist.gov/dave/). The AMBER force field and SPCE water model were used for modeling the NALMA solute and water, respectively. For the analysis of the water dynamics in the NALMA aqueous solutions, we performed simulations of a dispersed solute configuration consistent with our previous structural analysis, where we had primarily focused on the structural organization of these peptide solutions and their connection to protein folding. Further details of the QENS experiment and molecular dynamics simulations are reported elsewhere.

  8. Carbon Dioxide Hydrate Particles for Ocean Carbon Sequestration

    SciTech Connect (OSTI)

    Chow, Aaron C. [Massachusetts Institute of Technology (MIT); Adams, E. Eric [Massachusetts Institute of Technology (MIT); Israelsson, P. H. [Quantitative Environmental Analysis; Tsouris, Costas [ORNL

    2009-01-01T23:59:59.000Z

    This paper presents strategies for producing negatively buoyant CO{sub 2} hydrate composite particles for ocean carbon sequestration. Our study is based on recent field observations showing that a continuous-jet hydrate reactor located at an ocean depth of 1500 m produced curved negatively buoyant cylindrical particles with diameters {approx} 2.5 cm and lengths up to {approx} 1 m. Accordingly we performed new laboratory experiments to determine the drag coefficient of such particles and, based on the measured drag coefficient and the initial settling velocity observed in the field, have concluded that the reactor efficiency (percentage of liquid CO{sub 2} converted to hydrate) in the field was {approx} 16%. Using the dissolution rates observed in the field, we conclude that such particles would ultimately sink to depth below discharge of {approx} 115 m. We have also predicted the sinking depth of particles potentially produced from various scaled-up reactors and have shown that, for example, a 10 cm diameter particle produced with a hydrate conversion of 50% could reach the ocean bottom before completely dissolving. In a real sequestration scenario, we are interested in following large groups of hydrate particles released continuously. We have previously shown that increasing particle size and hydrate conversion efficiency enhances the sinking of hydrate particle plumes produced by the continuous release of CO{sub 2} in a quiescent ambient, but that a sufficiently strong current will cause the entrained particles to separate from the plume and settle discretely. In the latter case, particles of different sizes and hydrate conversions (hence different settling velocities) will follow different settling trajectories as they dissolve. This particle fractionation, if employed deliberately, spreads the discharged CO{sub 2} in the down current and vertical directions, enhancing mixing, while turbulent diffusion helps spread the CO{sub 2} in the third direction. A numerical model that incorporates these processes is used to predict the downstream concentrations and changes in pH from such particle plumes in a 'strong' current. An extension of this model simulates hydrate particles that are released continuously from a moving ship. Because of the ship speed, such particles would never form a coherent plume, but the combination of particle fractionation and advection due to the ship motion produces excellent dilution of the discharged CO{sub 2}.

  9. Integrating Natural Gas Hydrates in the Global Carbon Cycle

    SciTech Connect (OSTI)

    David Archer; Bruce Buffett

    2011-12-31T23:59:59.000Z

    We produced a two-dimensional geological time- and basin-scale model of the sedimentary margin in passive and active settings, for the simulation of the deep sedimentary methane cycle including hydrate formation. Simulation of geochemical data required development of parameterizations for bubble transport in the sediment column, and for the impact of the heterogeneity in the sediment pore fluid flow field, which represent new directions in modeling methane hydrates. The model is somewhat less sensitive to changes in ocean temperature than our previous 1-D model, due to the different methane transport mechanisms in the two codes (pore fluid flow vs. bubble migration). The model is very sensitive to reasonable changes in organic carbon deposition through geologic time, and to details of how the bubbles migrate, in particular how efficiently they are trapped as they rise through undersaturated or oxidizing chemical conditions and the hydrate stability zone. The active margin configuration reproduces the elevated hydrate saturations observed in accretionary wedges such as the Cascadia Margin, but predicts a decrease in the methane inventory per meter of coastline relative to a comparable passive margin case, and a decrease in the hydrate inventory with an increase in the plate subduction rate.

  10. Structural stability of methane hydrate at high pressures

    SciTech Connect (OSTI)

    Shu, Jinfu; Chen, Xiaojia; Chou, I.-Ming; Yang, Wenge; Hu, Jingzhu; Hemley, Russell J.; Mao, Ho-kwang

    2011-01-01T23:59:59.000Z

    The structural stability of methane hydrate under pressure at room temperature was examined by both in-situ single-crystal and powder X-ray diffraction techniques on samples with structure types I, II, and H in diamond-anvil cells. The diffraction data for types II (sII) and H (sH) were refined to the known structures with space groups Fd3m and P6{sub 3}/mmc, respectively. Upon compression, sI methane hydrate transforms to the sII phase at 120 MPa, and then to the sH phase at 600 MPa. The sII methane hydrate was found to coexist locally with sI phase up to 500 MPa and with sH phase up to 600 MPa. The pure sH structure was found to be stable between 600 and 900 MPa. Methane hydrate decomposes at pressures above 3 GPa to form methane with the orientationally disordered Fm3m structure and ice VII (Pn3m). The results highlight the role of guest (CH{sub 4})-host (H{sub 2}O) interactions in the stabilization of the hydrate structures under pressure.

  11. Variability of the methane trapping in martian subsurface clathrate hydrates

    E-Print Network [OSTI]

    Caroline Thomas; Olivier Mousis; Sylvain Picaud; Vincent Ballenegger

    2008-10-23T23:59:59.000Z

    Recent observations have evidenced traces of methane CH4 heterogeneously distributed in the martian atmosphere. However, because the lifetime of CH4 in the atmosphere of Mars is estimated to be around 300-600 years on the basis of photochemistry, its release from a subsurface reservoir or an active primary source of methane have been invoked in the recent literature. Among the existing scenarios, it has been proposed that clathrate hydrates located in the near subsurface of Mars could be at the origin of the small quantities of the detected CH4. Here, we accurately determine the composition of these clathrate hydrates, as a function of temperature and gas phase composition, by using a hybrid statistical thermodynamic model based on experimental data. Compared to other recent works, our model allows us to calculate the composition of clathrate hydrates formed from a more plausible composition of the martian atmosphere by considering its main compounds, i.e. carbon dioxyde, nitrogen and argon, together with methane. Besides, because there is no low temperature restriction in our model, we are able to determine the composition of clathrate hydrates formed at temperatures corresponding to the extreme ones measured in the polar caps. Our results show that methane enriched clathrate hydrates could be stable in the subsurface of Mars only if a primitive CH4-rich atmosphere has existed or if a subsurface source of CH4 has been (or is still) present.

  12. Home | Product Information | About Us | Heat Technology | What's New | Parts & Service | Contact Us Call 1-800-323-0620 for Fast Service

    E-Print Network [OSTI]

    Haller, Gary L.

    Home | Product Information | About Us | Heat Technology | What's New | Parts & Service | Contact Us Call 1-800-323-0620 for Fast Service MASTER HEAT GUN REPLACEMENT PARTS ITEM NO. UPC NO. Model NO-Murphy #12;Call 1-800-323-0620 for Fast Service HOME BACK TO PARTS LISTING 42

  13. Effects of Hydration and Oxygen Vacancy on CO2 Adsorption and...

    Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

    Hydration and Oxygen Vacancy on CO2 Adsorption and Activation on ?-Ga2O3(100). Effects of Hydration and Oxygen Vacancy on CO2 Adsorption and Activation on ?-Ga2O3(100)....

  14. Transparent hydrogel with enhanced water retention capacity by introducing highly hydratable salt

    E-Print Network [OSTI]

    Suo, Zhigang

    Transparent hydrogel with enhanced water retention capacity by introducing highly hydratable salt 2014; published online 14 October 2014) Polyacrylamide hydrogels containing salt as electrolyte have of polyacrylamide hydrogel by introducing highly hydratable salts into the hydrogel. These hydrogels show enhanced

  15. NISTIR 7232 CEMHYD3D: A Three-Dimensional Cement Hydration

    E-Print Network [OSTI]

    Bentz, Dale P.

    NISTIR 7232 CEMHYD3D: A Three-Dimensional Cement Hydration and Microstructure Development Modeling Package. Version 3.0 Dale P. Bentz #12;NISTIR 7232 CEMHYD3D: A Three-Dimensional Cement Hydration

  16. Dynamics of biopolymers and their hydration water studied by neutron and X-ray scattering

    E-Print Network [OSTI]

    Chu, Xiang-qiang

    2010-01-01T23:59:59.000Z

    Protein functions are intimately related to their dynamics. Moreover, protein hydration water is believed to have significant influence on the dynamics of proteins. One of the evidence is that both protein and its hydration ...

  17. Experimental evidence of logarithmic relaxation in single-particle dynamics of hydrated protein molecules

    E-Print Network [OSTI]

    Chen, Sow-Hsin

    Experimental evidence of logarithmic relaxation in single-particle dynamics of hydrated protein dynamics of hydrated lysozyme powder follows a logarithmic relax- ation in the time domain. In particular

  18. Methane Hydrate Formation and Dissocation in a Partially Saturated Sand--Measurements and Observations

    SciTech Connect (OSTI)

    Kneafsey, Timothy J.; Tomutsa, Liviu; Moridis, George J.; Seol, Yongkoo; Freifeld, Barry; Taylor, Charles E.; Gupta, Arvind

    2005-03-01T23:59:59.000Z

    We performed a sequence of tests on a partially water-saturated sand sample contained in an x-ray transparent aluminum pressure vessel that is conducive to x-ray computed tomography (CT) observation. These tests were performed to gather data for estimation of thermal properties of the sand/water/gas system and the sand/hydrate/water/gas systems, as well as data to evaluate the kinetic nature of hydrate dissociation. The tests included mild thermal perturbations for the estimation of the thermal properties of the sand/water/gas system, hydrate formation, thermal perturbations with hydrate in the stability zone, hydrate dissociation through thermal stimulation, additional hydrate formation, and hydrate dissociation through depressurization with thermal stimulation. Density changes throughout the sample were observed as a result of hydrate formation and dissociation, and these processes induced capillary pressure changes that altered local water saturation.

  19. Site Selection for DOE/JIP Gas Hydrate Drilling in the Northern Gulf of Mexico

    SciTech Connect (OSTI)

    Collett, T.S. (USGS); Riedel, M. (McGill Univ., Montreal, Quebec, Canada); Cochran, J.R. (Columbia Univ., Palisades, NY); Boswell, R.M.; Kumar, Pushpendra (Oil and Natural Gas Corporation Ltd., Navi Mumbai, India); Sathe, A.V. (Oil and Natural Gas Corporation Ltd., Uttaranchal, INDIA)

    2008-07-01T23:59:59.000Z

    Studies of geologic and geophysical data from the offshore of India have revealed two geologically distinct areas with inferred gas hydrate occurrences: the passive continental margins of the Indian Peninsula and along the Andaman convergent margin. The Indian National Gas Hydrate Program (NGHP) Expedition 01 was designed to study the occurrence of gas hydrate off the Indian Peninsula and along the Andaman convergent margin with special emphasis on understanding the geologic and geochemical controls on the occurrence of gas hydrate in these two diverse settings. NGHP Expedition 01 established the presence of gas hydrates in Krishna- Godavari, Mahanadi and Andaman basins. The expedition discovered one of the richest gas hydrate accumulations yet documented (Site 10 in the Krishna-Godavari Basin), documented the thickest and deepest gas hydrate stability zone yet known (Site 17 in Andaman Sea), and established the existence of a fully-developed gas hydrate system in the Mahanadi Basin (Site 19).

  20. Analysis of the Development of Messoyakha Gas Field: A Commercial Gas Hydrate Reservoir

    E-Print Network [OSTI]

    Omelchenko, Roman 1987-

    2012-12-11T23:59:59.000Z

    the presence of gas hydrates in the Messoyakha field was not a certainty, this current study determined the undeniable presence of gas hydrates in the reservoir. This study uses four models of the Messoyakha field structure and reservoir conditions...