Powered by Deep Web Technologies
Note: This page contains sample records for the topic "hybrid tractor evaluation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Coca-Cola Refreshments Class 8 Diesel Electric Hybrid Tractor Evaluation: 13-Month Final Report  

SciTech Connect

This 13-month evaluation used five Kenworth T370 hybrid tractors and five Freightliner M2106 standard diesel tractors at a Coca Cola Refreshments facility in Miami, Florida. The primary objective was to evaluate the fuel economy, emissions, and operational field performance of hybrid electric vehicles when compared to similar-use conventional diesel vehicles. A random dispatch system ensures the vehicles are used in a similar manner. GPS logging, fueling, and maintenance records and laboratory dynamometer testing are used to evaluate the performance of these hybrid tractors. Both groups drive similar duty cycles with similar kinetic intensity (0.95 vs. 0.69), average speed (20.6 vs. 24.3 mph), and stops per mile (1.9 vs. 1.5). The study demonstrated the hybrid group had a 13.7% fuel economy improvement over the diesel group. Laboratory fuel economy and field fuel economy study showed similar trends along the range of KI and stops per mile. Hybrid maintenance costs were 51% lower per mile; hybrid fuel costs per mile were 12% less than for the diesels; and hybrid vehicle total cost of operation per mile was 24% less than the cost of operation for the diesel group.

Walkowicz, K.; Lammert, M.; Curran, P.

2012-08-01T23:59:59.000Z

2

Coca-Cola Refreshments Class 8 Diesel Electric Hybrid Tractor Evaluation: 13-Month Final Report  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Coca-Cola Refreshments Coca-Cola Refreshments Class 8 Diesel Electric Hybrid Tractor Evaluation: 13-Month Final Report K. Walkowicz, M. Lammert, and P. Curran Technical Report NREL/TP-5400-53502 August 2012 NREL is a national laboratory of the U.S. Department of Energy, Office of Energy Efficiency & Renewable Energy, operated by the Alliance for Sustainable Energy, LLC. National Renewable Energy Laboratory 15013 Denver West Parkway Golden, Colorado 80401 303-275-3000 * www.nrel.gov Contract No. DE-AC36-08GO28308 Coca-Cola Refreshments Class 8 Diesel Electric Hybrid Tractor Evaluation: 13-Month Final Report K. Walkowicz, M. Lammert, and P. Curran Prepared under Task No. FC08.3000 Technical Report NREL/TP-5400-53502 August 2012 NOTICE

3

Plug-in Hybrid Electric Yard Tractor Next Generation Recommendations  

Science Conference Proceedings (OSTI)

Diesel-powered tractors that pull containers and cargo are used extensively in ports, warehouses, and other applications to shuttle cargo trailers from point to point within the confines of a specific facility, terminal, or yard. Often called yard tractors, yard hostlers, or terminal tractors, these vehicles are of a specific design with a single driver compartment and a fifth wheel that can be raised and lowered. These widely used yard tractors are unique to the cargo ...

2012-11-30T23:59:59.000Z

4

Plug-In Hybrid Electric Vehicle Yard Tractor: Performance Characterization Report  

Science Conference Proceedings (OSTI)

Diesel-powered tractors, called yard tractors, are used to shuttle cargo trailers from point to point within the confines of a port facility, terminal, or yard. A plug-in hybrid electric vehicle (PHEV) yard tractor design was proposed as a way to reduce operation emissions and diesel fuel use. In 2007, the Electric Power Research Institute (EPRI) began work on the design and construction of a first-of-a-kind PHEV yard tractor. In 2009, Southern California Edison (SCE) tested the completed PHEV yard trac...

2012-02-20T23:59:59.000Z

5

U.S. Hybrid and Lithium Technology Corporation GAIA Battery: Initial System Characterization for the Plug-In Hybrid Electric Vehicle Yard Tractor  

Science Conference Proceedings (OSTI)

Diesel-powered tractors, called yard tractors, are used to shuttle cargo trailers from point to point within the confines of a port facility, terminal, or yard. A plug-in hybrid electric vehicle (PHEV) yard tractor design was proposed as a way to reduce operation emissions and diesel fuel use. The Electric Power Research Institute (EPRI) has designed and constructed a first-of-a-kind PHEV yard tractor. Southern California Edison's (SCE's) Electric Vehicle Technical Center performed PHEV yard tractor bat...

2012-03-01T23:59:59.000Z

6

Plug-in Hybrid Electric Vehicle Yard Tractor: Field Demonstration Results  

Science Conference Proceedings (OSTI)

The fuel economy results for US Hybrid's plug-in hybrid electric vehicle (PHEV) yard tractor, like all PHEVs, is sensitive to the manner in which the operator uses the vehicle and also to different duty cycles, terrain, temperature, and the frequency of charging. At three of the ports, the PHEV operated with a fuel consumption of 1.0 to 1.2 gallons per hour (gph) and 2.3 to 5.7 miles per gallon (mpg) in various duty modes. At the Port of Savannah, where it was solidly operated for only a week, it obtaine...

2011-12-29T23:59:59.000Z

7

Microhole Drilling Tractor Technology Development  

SciTech Connect

In an effort to increase the U.S. energy reserves and lower costs for finding and retrieving oil, the USDOE created a solicitation to encourage industry to focus on means to operate in small diameter well-Microhole. Partially in response to this solicitation and because Western Well Tool's (WWT) corporate objective to develop small diameter coiled tubing drilling tractor, WWT responded to and was awarded a contract to design, prototype, shop test, and field demonstrate a Microhole Drilling Tractor (MDT). The benefit to the oil industry and the US consumer from the project is that with the MDT's ability to facilitate Coiled Tubing drilled wells to be 1000-3000 feet longer horizontally, US brown fields can be more efficiently exploited resulting in fewer wells, less environmental impact, greater and faster oil recovery, and lower drilling costs. Shortly after award of the contract, WWT was approached by a major oil company that strongly indicated that the specified size of a tractor of 3.0 inches diameter was inappropriate and that immediate applications for a 3.38-inch diameter tractor would substantially increase the usefulness of the tool to the oil industry. Based on this along with an understanding with the oil company to use the tractor in multiple field applications, WWT applied for and was granted a no-cost change-of-scope contract amendment to design, manufacture, assemble, shop test and field demonstrate a prototype a 3.38 inch diameter MDT. Utilizing existing WWT tractor technology and conforming to an industry developed specification for the tool, the Microhole Drilling Tractor was designed. Specific features of the MDT that increase it usefulness are: (1) Operation on differential pressure of the drilling fluid, (2) On-Off Capability, (3) Patented unique gripping elements (4) High strength and flexibility, (5) Compatibility to existing Coiled Tubing drilling equipment and operations. The ability to power the MDT with drilling fluid results in a highly efficient tool that both delivers high level of force for the pressure available and inherently increases downhole reliability because parts are less subject to contamination. The On-Off feature is essential to drilling to allow the Driller to turn off the tractor and pull back while circulating in cleanout runs that keep the hole clean of drilling debris. The gripping elements have wide contact surfaces to the formation to allow high loads without damage to the formation. As part of the development materials evaluations were conducted to verify compatibility with anticipated drilling and well bore fluids. Experiments demonstrated that the materials of the tractor are essentially undamaged by exposure to typical drilling fluids used for horizontal coiled tubing drilling. The design for the MDT was completed, qualified vendors identified, parts procured, received, inspected, and a prototype was assembled. As part of the assembly process, WWT prepared Manufacturing instructions (MI) that detail the assembly process and identify quality assurance inspection points. Subsequent to assembly, functional tests were performed. Functional tests consisted of placing the MDT on jack stands, connecting a high pressure source to the tractor, and verifying On-Off functions, walking motion, and operation over a range of pressures. Next, the Shop Demonstration Test was performed. An existing WWT test fixture was modified to accommodate operation of the 3.38 inch diameter MDT. The fixture simulated the tension applied to a tractor while walking (pulling) inside 4.0 inch diameter pipe. The MDT demonstrated: (1) On-off function, (2) Pulling forces proportional to available differential pressure up to 4000 lbs, (3) Walking speeds to 1100 ft/hour. A field Demonstration of the MDT was arranged with a major oil company operating in Alaska. A demonstration well with a Measured Depth of approximately 15,000 ft was selected; however because of problems with the well drilling was stopped before the planned MDT usage. Alternatively, functional and operational tests were run with the MDT insi

Western Well Tool

2007-07-09T23:59:59.000Z

8

Test, Evaluation, and Demonstration of Practical Devices/Systems to Reduce Aerodynamic Drag of Tractor/Semitrailer Combination Unit Trucks  

DOE Green Energy (OSTI)

Class 8 heavy-duty trucks account for over three-quarters of the total diesel fuel used by commercial trucks (trucks with GVWRs more than 10,000 pounds) in the United States each year. At the highway speeds at which these trucks travel (i.e., 60 mph or greater), aerodynamic drag is a major part of total horsepower needed to move the truck down the highway, Reductions in aerodynamic drag can yield measurable benefits in fuel economy through the use of relatively inexpensive and simple devices. The goal of this project was to examine a number of aerodynamic drag reduction devices and systems and determine their effectiveness in reducing aerodynamic drag of Class 8 tractor/semitrailer combination-units, thus contributing to DOE's goal of reducing transportation petroleum use. The project team included major heavy truck manufacturers in the United States, along with the management and industry expertise of the Truck Manufacturers Association as the lead investigative organization. The Truck Manufacturers Association (TMA) is the national trade association representing the major North American manufacturers of Class 6-8 trucks (GVWRs over 19,500 lbs). Four major truck manufacturers participated in this project with TMA: Freightliner LLC; International Truck and Engine Corporation; Mack Trucks Inc.; and Volvo Trucks North America, Inc. Together, these manufacturers represent over three-quarters of total Class 8 truck sales in the United States. These four manufacturers pursued complementary research efforts as part of this project. The project work was separated into two phases conducted over a two-year period. In Phase I, candidate aerodynamic devices and systems were screened to focus research and development attention on devices that offered the most potential. This was accomplished using full-size vehicle tests, scale model tests, and computational fluid dynamics analyses. In Phase II, the most promising devices were installed on full-size trucks and their effect on fuel economy was determined, either through on-road testing or full-size wind tunnel testing. All of the manufacturers worked with devices and systems that offer practical solutions to reduce aerodynamic drag, accounting for functionality, durability, cost effectiveness, reliability, and maintainability. The project team members and their roles and responsibilities are shown in Figure 2-1. Figure 2-2 shows the Phase I and II project schedules for all four projects and associated management activities.

Scott Smith; Karla Younessi; Matt Markstaller; Dan Schlesinger; Bhaskar Bhatnagar; Donald Smith; Bruno Banceu; Ron Schoon; V.K. Sharma; Mark Kachmarsky; Srikant Ghantae; Michael Sorrels; Conal Deedy; Justin Clark; Skip Yeakel; Michael D. Laughlin; Charlotte Seigler; Sidney Diamond

2007-04-30T23:59:59.000Z

9

Condensing Hybrid Water Heater Monitoring Field Evaluation  

NLE Websites -- All DOE Office Websites (Extended Search)

Condensing Hybrid Water Heater Condensing Hybrid Water Heater Monitoring Field Evaluation Jeff Maguire, Lieko Earle, and Chuck Booten National Renewable Energy Laboratory C.E. Hancock Mountain Energy Partnership Produced under direction of the Sacramento Municipal Utilities District by the National Renewable Energy Laboratory (NREL) under Interagency Agreement CRD-05-168 and Task No WR49.3000. Technical Report NREL/TP-5500-52234 October 2011 NREL is a national laboratory of the U.S. Department of Energy, Office of Energy Efficiency & Renewable Energy, operated by the Alliance for Sustainable Energy, LLC. National Renewable Energy Laboratory 1617 Cole Boulevard Golden, Colorado 80401 303-275-3000 * www.nrel.gov Contract No. DE-AC36-08GO28308

10

United Parcel Service Evaluates Hybrid Electric Delivery Vans...  

NLE Websites -- All DOE Office Websites (Extended Search)

fuel economy than comparable conventional vans. United Parcel Service Evaluates Hybrid Electric Delivery Vans Advanced Vehicle Testing This project is part of a series of...

11

NREL: Fleet Test and Evaluation - Hybrid Electric Drive Systems  

NLE Websites -- All DOE Office Websites (Extended Search)

Hybrid Electric Drive Systems Hybrid Electric Drive Systems The Fleet Test and Evaluation Team conducts performance evaluations of hybrid electric drive systems in fleets of delivery vehicles and transit buses. Hybrid electric drive systems combine a primary power source, an energy storage system, and an electric motor to achieve a combination of emissions, fuel economy, and range benefits unattainable with any of these technologies alone. Hybrid electric drive systems use less petroleum-based fuel and capture energy created during breaking and idling. This collected energy is used to propel the vehicle during normal drive cycles. The batteries supply additional power for acceleration and hill climbing. Learn more about the team's hybrid electric drive system evaluations: Delivery Vehicles

12

King County Metro Transit Hybrid Articulated Buses: Final Evaluation Results  

DOE Green Energy (OSTI)

Final technical report compares and evaluates new diesel and diesel hybrid-electric articulated buses operated as part of the King County Metro Transit (KC Metro) fleet in Seattle, Washington. The evaluation lasted 12 months.

Chandler, K.; Walkowicz, K.

2006-12-01T23:59:59.000Z

13

FedEx Express Gasoline Hybrid Electric Delivery Truck Evaluation...  

NLE Websites -- All DOE Office Websites (Extended Search)

FedEx Express Gasoline Hybrid Electric Delivery Truck Evaluation: 12-Month Report R. Barnitt Technical Report NRELTP-5400-48896 January 2011 NREL is a national laboratory of the...

14

NREL: Fleet Test and Evaluation - Hydraulic Hybrid Drive Systems  

NLE Websites -- All DOE Office Websites (Extended Search)

Hydraulic Hybrid Drive Systems Hydraulic Hybrid Drive Systems NREL's Fleet Test and Evaluation Team conducts performance evaluations of hydraulic hybrid drive systems in delivery vehicles. Because hydraulic hybrids feature highly efficient regenerative braking systems and "engine off at idle" capabilities, they are ideal for parcel delivery applications where stop-and-go traffic is common. Hydraulic hybrid systems can capture up to 70% of the kinetic energy that would otherwise be lost during braking. This energy drives a pump, which transfers hydraulic fluid from a low-pressure reservoir to a high-pressure accumulator. When the vehicle accelerates, fluid in the high-pressure accumulator moves to the lower-pressure reservoir, which drives a motor and provides extra torque. This process can improve the vehicle's fuel economy

15

Condensing Hybrid Water Heater Monitoring Field Evaluation  

Science Conference Proceedings (OSTI)

This paper summarizes the Mascot home, an abandoned property that was extensively renovated. Several efficiency upgrades were integrated into this home, of particular interest, a unique water heater (a Navien CR240-A). Field monitoring was performed to determine the in-use efficiency of the hybrid condensing water heater. The results were compared to the unit's rated efficiency. This unit is Energy Star qualified and one of the most efficient gas water heaters currently available on the market.

Maguire, J.; Earle, L.; Booten, C.; Hancock, C. E.

2011-10-01T23:59:59.000Z

16

United Parcel Service Evaluates Hybrid Electric Delivery Vans (Fact Sheet)  

DOE Green Energy (OSTI)

This fact sheet describes how the National Renewable Energy Laboratory's Fleet Test and Evaluation team evaluated the 12-month, in-service performance of six Class 4 hybrid electric delivery vans - fueled by regular diesel - and six comparable conventional diesel vans operated by the United Parcel Service.

Not Available

2010-02-01T23:59:59.000Z

17

A hybrid ANP evaluation model for electronic service quality  

Science Conference Proceedings (OSTI)

Previous research has developed evaluation measurement for electronic service quality (e-SQ) but has ignored the interdependence perspective of the criteria and sub-criteria for e-SQ evaluation. Therefore, this study aims to propose a hybrid analytic ... Keywords: Analytic network process (ANP), Consistent fuzzy preference relations method, Electronic service quality (e-SQ)

Tsuen-Ho Hsu; Li-Chu Hung; Jia-Wei Tang

2012-01-01T23:59:59.000Z

18

Emissions and efficiency of agricultural diesels using low-proof ethanol as supplement fuel. [Tractor engines  

Science Conference Proceedings (OSTI)

Experimental investigations were made to evaluate the potential of using low-proof ethanol to supplement diesel fuel in agricultural engines. Fumigation, mechanical emulsification, and chemical emulsifiers were used to introduce a significant amount of alcohol with diesel fuel for engine operation. A total of five diesel tractor engines were tested using each of the fuel systems. Exhaust products and fuel usage were determined at various engine speed/load conditions. 5 references, 12 figures, 14 tables.

Allsup, J.R.; Clingenpeel, J.M.

1984-01-01T23:59:59.000Z

19

Evaluation Of Potential Hybrid Electric Vehicle Applications: Vol I  

E-Print Network (OSTI)

Vehicle Symposium, "The Hybrid Vehicle Revisited", OctoberBus Hv REFERENCES “Hybrid Vehicle Assessment, Phase I,Laboratory, March 1984 “Hybrid Vehicle Engineering Task”

Gris, Arturo E.

1991-01-01T23:59:59.000Z

20

Evaluation Of Potential Hybrid Electric Vehicle Applications: Vol I  

E-Print Network (OSTI)

of Potential Hybrid Electric Vehicle Applications Volume IOF POTENTIAL HYBRID ELECTRIC VEHICLE APPLICATIONS VOLUME IVIII International Electric Vehicle Symposium, "The Hybrid

Gris, Arturo E.

1991-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "hybrid tractor evaluation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Project Startup: Evaluating Coca-Cola's Class 8 Hybrid-Electric Delivery Trucks (Fact Sheet)  

DOE Green Energy (OSTI)

Fact sheet describing the project startup for evaluating Coca-Cola's Class 8 hybrid-electric delivery trucks.

Not Available

2011-03-01T23:59:59.000Z

22

New York City Transit Hybrid and CNG Transit Buses: Final Evaluation Results  

DOE Green Energy (OSTI)

This report describes the evaluation results for new Orion VII buses at NYCT with CNG propulsion and new hybrid propulsion.

Barnitt, R.; Chandler, K.

2006-11-01T23:59:59.000Z

23

King County Metro Transit Hybrid Articulated Buses: Interim Evaluation Results  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

King County Metro Transit King County Metro Transit Hybrid Articulated Buses: Interim Evaluation Results K. Chandler Battelle K. Walkowicz National Renewable Energy Laboratory Technical Report NREL/TP-540-39742 April 2006 King County Metro Transit Hybrid Articulated Buses: Interim Evaluation Results K. Chandler Battelle K. Walkowicz National Renewable Energy Laboratory Prepared under Task No. FC06.3000 Technical Report NREL/TP-540-39742 April 2006 National Renewable Energy Laboratory 1617 Cole Boulevard, Golden, Colorado 80401-3393 303-275-3000 * www.nrel.gov Operated for the U.S. Department of Energy Office of Energy Efficiency and Renewable Energy by Midwest Research Institute * Battelle Contract No. DE-AC36-99-GO10337 NOTICE This report was prepared as an account of work sponsored by an agency of the United States government.

24

Multi-Location Evaluation of Agronomic Traits in Maize Hybrids  

E-Print Network (OSTI)

Maize (Zea mays L.) is one of the main crops grown in the United States. Genetic improvement over the last century has seen a shift from using open-pollinated varieties to single cross hybrids. This has resulted in major grain yield gains and improved management methodologies. However, there is still concern about reduced genetic diversity in elite corn germplasm and the potential effects this could have on future maize productivity in the presence of numerous abiotic and biotic pressures. One solution to this issue is the incorporation of exotic germplasm into existing maize improvement programs. This exotic material must be evaluated and characterized because too much or poorly matched exotic material can lead to reduced productivity. The use of multiple environments representative to the target improvement area is the best way to determine the true potential of certain material. The objectives of this research were to: i) estimate the responses of hybrids to aflatoxin and their agronomic performance across a range of environments under inoculation with Aspergillus flavus; ii) identify the hybrids within each group that exhibit the lowest levels of contamination; iii) analyze the relationship between agronomic performance and aflatoxin accumulation; and iv) determine how Genotype x Environment interactions affect these traits. Agronomic data was collected in ten Texas environments in 2005 for hybrids created from yellow, white, and Quality Protein Maize material that was crossed with one of two elite temperate inbred testers, LH195 or LH210. Response to aflatoxin was measured in eight of these environments. U.S. commercial hybrids were used as checks. Significant differences between hybrids were observed at different environments for different traits. Overall the experimental hybrids had lower aflatoxin accumulation than the commercial checks. They also yielded lower and had lower test weights and 1000 kernel weights. However, there were some hybrids that were competitive with the commercial checks for these agronomic traits. The incorporation of this material into established U.S. lines could be beneficial with regards to aflatoxin accumulation and kernel quality, which could ultimately translate to higher yields and crop quality.

McKee, Michael 1982-

2012-12-01T23:59:59.000Z

25

Better than blasting for blackwells. [Tractor-mounted ripper  

SciTech Connect

On opencasting, quarrying and rock removal generally, a tractor-mounted ripper is usually felt to be safer and quieter than drilling and blasting with high explosive. Helped by Newram Plant Limited, C.A. Blackwell (Contracts) Limited are seeing if this really is so and if ripping also has any economic and performance advantages.

1979-10-01T23:59:59.000Z

26

A System for Semi-Autonomous Tractor Operations  

Science Conference Proceedings (OSTI)

Tractors are the workhorses of the modern farm. By automating these machines, we can increase the productivity, improve safety, and reduce costs for many agricultural operations. Many researchers have tested computer-controlled machines for farming, ... Keywords: agricultural robots, obstacle detection, path tracking, position estimation, sensor fusion

Anthony Stentz; Cristian Dima; Carl Wellington; Herman Herman; David Stager

2002-07-01T23:59:59.000Z

27

FedEx Gasoline Hybrid Electric Delivery Truck Evaluation: 6-Month...  

NLE Websites -- All DOE Office Websites (Extended Search)

7693 May 2010 FedEx Gasoline Hybrid Electric Delivery Truck Evaluation: 6-Month Interim Report R. Barnitt National Renewable Energy Laboratory 1617 Cole Boulevard, Golden, Colorado...

28

New York City Transit Hybrid and CNG Transit Buses: Interim Evaluation Results  

DOE Green Energy (OSTI)

This report focuses on the evaluation of compressed natural gas (CNG) and diesel hybrid electric bus propulsion systems in New York City Transit's transit buses.

Chandler, K.; Eberts, E.; Eudy, L.

2006-01-01T23:59:59.000Z

29

Characterization and Evaluation of Hybrid Polarization Observation of Precipitation  

Science Conference Proceedings (OSTI)

Transmitting an arbitrary state of polarization while receiving horizontal–vertical polarization states is termed the hybrid polarization mode of operation. A theoretical model is developed for hybrid mode dual-polarization measurements in terms ...

Yanting Wang; V. Chandrasekar; V. N. Bringi

2006-04-01T23:59:59.000Z

30

Ultracapacitor Applications and Evaluation for Hybrid Electric Vehicles (Presentation)  

DOE Green Energy (OSTI)

Describes the use of ultracapacitors in advanced hybrid and electric vehicles and discusses thermal and electrical testing of lithium ion capacitors for HEV applications.

Pesaran, A.; Gonder, J.; Keyser, M.

2009-04-01T23:59:59.000Z

31

Thirty-Six Month Evaluation of UPS Diesel Hybrid-Electric Delivery Vans  

DOE Green Energy (OSTI)

This evaluation compared six hybrids and six standard diesels in UPS facilities in Phoenix, Arizona. Dispatch and maintenance practices are the same at both facilities. GPS logging, fueling, and maintenance records are used to evaluate the performance of these step delivery vans. The hybrids' average monthly mileage rate was 18% less than the diesel vans. The hybrids consistently were driven a fewer number of miles throughout the evaluation period. The hybrids idled more and operating at slower speeds than the diesels, and the diesels spent slightly more time operating at greater speeds, accounting for much of the hybrids fewer monthly miles. The average fuel economy for the hybrid vans is 13.0 mpg, 23% greater than the diesel vans 10.6 mpg. Total hybrid maintenance cost/mile of $0.141 was 9% more than the $0.130 for the diesel vans. Propulsion-related maintenance cost/mile of $0.037 for the hybrid vans was 25% more than the $0.029 for the diesel vans. Neither difference was found to be statistically significant. The hybrid group had a cumulative average of 96.3% uptime, less than the diesel group's 99.0% uptime. The hybrids experienced troubleshooting and recalibration issues related to prototype components that were primarily responsible for the lower uptime figures.

Lammert, M.; Walkowicz, K.

2012-03-01T23:59:59.000Z

32

Comparative performance evaluation of global-local hybrid ensemble  

Science Conference Proceedings (OSTI)

This paper presents a comprehensive simulation study which aims to profile the performance capabilities of the global-local hybrid ensemble in comparison with leading ensemble classifiers as reported in recent studies in the literature. The global-local ... Keywords: Hybrid ensemble, classification, global/local learning, heterogeneous/homogeneous diversity, nonparametric comparison

Dustin Baumgartner; Gursel Serpen

2011-04-01T23:59:59.000Z

33

Hybrid  

NLE Websites -- All DOE Office Websites (Extended Search)

may prove to be a limitation for realizing technologies for very high gradient accelerators. In this article, we present a scheme that uses a hybrid dielectric and iris-loaded...

34

Evaluation of 2004 Toyota Prius Hybrid Electric Drive System  

SciTech Connect

The 2004 Toyota Prius is a hybrid automobile equipped with a gasoline engine and a battery- and generator-powered electric motor. Both of these motive-power sources are capable of providing mechanical-drive power for the vehicle. The engine can deliver a peak-power output of 57 kilowatts (kW) at 5000 revolutions per minute (rpm) while the motor can deliver a peak-power output of 50 kW over the speed range of 1200-1540 rpm. Together, this engine-motor combination has a specified peak-power output of 82 kW at a vehicle speed of 85 kilometers per hour (km/h). In operation, the 2004 Prius exhibits superior fuel economy compared to conventionally powered automobiles. To acquire knowledge and thereby improve understanding of the propulsion technology used in the 2004 Prius, a full range of design characterization studies were conducted to evaluate the electrical and mechanical characteristics of the 2004 Prius and its hybrid electric drive system. These characterization studies included (1) a design review, (2) a packaging and fabrication assessment, (3) bench-top electrical tests, (4) back-electromotive force (emf) and locked rotor tests, (5) loss tests, (6) thermal tests at elevated temperatures, and most recently (7) full-design-range performance testing in a controlled laboratory environment. This final test effectively mapped the electrical and thermal results for motor/inverter operation over the full range of speeds and shaft loads that these assemblies are designed for in the Prius vehicle operations. This testing was undertaken by the Oak Ridge National Laboratory (ORNL) as part of the U.S. Department of Energy (DOE) - Energy Efficiency and Renewable Energy (EERE) FreedomCAR and Vehicle Technologies (FCVT) program through its vehicle systems technologies subprogram. The thermal tests at elevated temperatures were conducted late in 2004, and this report does not discuss this testing in detail. The thermal tests explored the derating of the Prius motor design if operated at temperatures as high as is normally encountered in a vehicle engine. The continuous ratings at base speed (1200 rpm) with different coolant temperatures are projected from test data at 900 rpm. A separate, comprehensive report on this thermal control study is available [1].

Staunton, Robert H [ORNL; Ayers, Curtis William [ORNL; Chiasson, J. N. [University of Tennessee, Knoxville (UTK); Burress, Timothy A [ORNL; Marlino, Laura D [ORNL

2006-05-01T23:59:59.000Z

35

Evaluation of 2004 Toyota Prius Hybrid Electric Drive System  

SciTech Connect

The 2004 Toyota Prius is a hybrid automobile equipped with a gasoline engine and a battery- and generator-powered electric motor. Both of these motive-power sources are capable of providing mechanical-drive power for the vehicle. The engine can deliver a peak-power output of 57 kilowatts (kW) at 5000 revolutions per minute (rpm) while the motor can deliver a peak-power output of 50 kW over the speed range of 1200-1540 rpm. Together, this engine-motor combination has a specified peak-power output of 82 kW at a vehicle speed of 85 kilometers per hour (km/h). In operation, the 2004 Prius exhibits superior fuel economy compared to conventionally powered automobiles. To acquire knowledge and thereby improve understanding of the propulsion technology used in the 2004 Prius, a full range of design characterization studies were conducted to evaluate the electrical and mechanical characteristics of the 2004 Prius and its hybrid electric drive system. These characterization studies included (1) a design review, (2) a packaging and fabrication assessment, (3) bench-top electrical tests, (4) back-electromotive force (emf) and locked rotor tests, (5) loss tests, (6) thermal tests at elevated temperatures, and most recently (7) full-design-range performance testing in a controlled laboratory environment. This final test effectively mapped the electrical and thermal results for motor/inverter operation over the full range of speeds and shaft loads that these assemblies are designed for in the Prius vehicle operations. This testing was undertaken by the Oak Ridge National Laboratory (ORNL) as part of the U.S. Department of Energy (DOE)-Energy Efficiency and Renewable Energy (EERE) FreedomCAR and Vehicle Technologies (FCVT) program through its vehicle systems technologies subprogram. The thermal tests at elevated temperatures were conducted late in 2004, and this report does not discuss this testing in detail. The thermal tests explored the derating of the Prius motor design if operated at temperatures as high as is normally encountered in a vehicle engine. The continuous ratings at base speed (1200 rpm) with different coolant temperatures are projected from test data at 900 rpm. A separate, comprehensive report on this thermal control study is available [1].

Staunton, R.H.; Ayers, C.W.; Chiasson, J.N. (U Tennessee-Knoxville); Burress, B.A. (ORISE); Marlino, L.D.

2006-05-01T23:59:59.000Z

36

Evaluation of a Lower-Energy Energy Storage System (LEESS) for Full-Hybrid Electric Vehicles (HEVs) (Presentation)  

DOE Green Energy (OSTI)

This presentation discusses the evaluation of a lower-energy energy storage system for full-hybrid electric vehicles.

Gonder, J.; Ireland, J.; Cosgrove, J.

2013-04-01T23:59:59.000Z

37

Hybrid Plume Dispersion Model (HPDM) Development and Evaluation  

Science Conference Proceedings (OSTI)

The Hybrid Plume Dispersion Model (HPDM) was developed for application to tall stack plumes dispersing over nearly flat terrain. Emphasis is on convective and high-wind conditions. The meteorological component is based on observational and ...

Steven R. Hanna; Robert J. Paine

1989-03-01T23:59:59.000Z

38

NREL: Fleet Test and Evaluation - Electric and Plug-In Hybrid Electric  

NLE Websites -- All DOE Office Websites (Extended Search)

Electric and Plug-In Hybrid Electric Drive Systems Electric and Plug-In Hybrid Electric Drive Systems NREL's Fleet Test and Evaluation Team conducts performance evaluations of electric and plug-in hybrid electric drive systems in medium-duty trucks operated by fleets. Photo of medium-duty truck with the words "All Electric Vehicle" and "Plug-in" written on its side. NREL evaluates the performance of electric and plug-in hybrid electric vehicles in fleet operation. All-electric vehicles (EVs) use batteries to store the electric energy that powers the motor. EV batteries are charged by plugging the vehicle into an electric power source. Plug-in hybrid electric vehicles (PHEVs) are powered by an internal combustion engine that can run on conventional or alternative fuels and an electric motor that uses energy stored in batteries. The vehicle can be

39

Evaluating a Hybrid Prognostic–Diagnostic Model That Improves Wind Forecast Resolution in Complex Coastal Topography  

Science Conference Proceedings (OSTI)

The results from a hybrid approach that combines the forecasts of a mesoscale model with a diagnostic wind model to produce high-resolution wind forecasts in complex coastal orography are evaluated. The simple diagnostic wind model [Winds on ...

Francis L. Ludwig; Douglas K. Miller; Shawn G. Gallaher

2006-01-01T23:59:59.000Z

40

King County Metro Transit Hybrid Articulated Transit Buses: Interim Evaluation Results  

DOE Green Energy (OSTI)

Interim technical report compares and evaluates new diesel and diesel hybrid-electric articulated buses operated as part of the King County Metro Transit (KC Metro) fleet in Seattle, Washington.

Chandler, K.; Walkowicz, K.

2006-04-01T23:59:59.000Z

Note: This page contains sample records for the topic "hybrid tractor evaluation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Research of Speed Ratio Matching Strategies of Hydro-Mechanical Continuously Variable Transmission System for Tractor  

Science Conference Proceedings (OSTI)

To realize the optimal power and best fuel economy performance of engine, the speed ratio matching strategies of tractor with hydro-mechanical continuously variable transmission (HMCVT) system are studied. The engine output torque model and fuel consumption ... Keywords: Tractor, Hydro-mechanical continuously variable transmission, Speed ratio, Matching strategies

Liyou Xu; Zhili Zhou; Fuyi Cao; Mingzhu Zhang

2009-10-01T23:59:59.000Z

42

A Comparative Evaluation of Candidate Plug-in Hybrid Powertrain Architectures  

Science Conference Proceedings (OSTI)

This report evaluates three existing plug-in hybrid powertrain architecturespre-transmission, power-split, and series. Using simulation software, these powertrains were scaled so they could be compared side-to-side, each vehicle's components meeting the all-electric range targets for plug-in hybrid vehicle (PHEV) configurations. These powertrains were evaluated according to performance, emissions, fuel economy / fuel consumption, equivalent electric range, powertrain design, battery selection, and vehicl...

2007-12-17T23:59:59.000Z

43

Use of hybrid intelligent computing in mineral resources evaluation  

Science Conference Proceedings (OSTI)

Mineral resources are a formal quantification of naturally occurring materials. Estimation of resource parameters such as grade and thickness may be carried out using different methodologies. In this paper, a soft methodology, which is artificial neural ... Keywords: Fuzzy-neural network, Grade estimation, Hybrid modelling, Mineral resource

B. Tutmez

2009-06-01T23:59:59.000Z

44

Eighteen-Month Final Evaluation of UPS Second Generation Diesel Hybrid-Electric Delivery Vans  

Science Conference Proceedings (OSTI)

A parallel hybrid-electric diesel delivery van propulsion system was evaluated at a UPS facility in Minneapolis using on-vehicle data logging, fueling, and maintenance records. Route and drive cycle analysis showed different duty cycles for hybrid vs. conventional delivery vans; routes were switched between the study groups to provide a valid comparison. The hybrids demonstrated greater advantage on the more urban routes; the initial conventional vans' routes had less dense delivery zones. The fuel economy of the hybrids on the original conventional group?s routes was 10.4 mpg vs. 9.2 mpg for the conventional group on those routes a year earlier. The hybrid group's fuel economy on the original hybrid route assignments was 9.4 mpg vs. 7.9 mpg for the conventional group on those routes a year later. There was no statistically significant difference in total maintenance cost per mile or for the vehicle total cost of operation per mile. Propulsion-related maintenance cost per mile was 77% higher for the hybrids, but only 52% more on a cost-per-delivery-day basis. Laboratory dynamometer testing demonstrated 13%-36% hybrid fuel economy improvement, depending on duty cycle, and up to a 45% improvement in ton-mi/gal. NOx emissions increased 21%-49% for the hybrids in laboratory testing.

Lammert, M.; Walkowicz, K.

2012-09-01T23:59:59.000Z

45

Evaluation of the 2007 Toyota Camry Hybrid Syneregy Drive System  

Science Conference Proceedings (OSTI)

The U.S. Department of Energy (DOE) and American automotive manufacturers General Motors, Ford, and DaimlerChrysler began a five-year, cost-shared partnership in 1993. Currently, hybrid electric vehicle (HEV) research and development is conducted by DOE through its FreedomCAR and Vehicle Technologies (FCVT) program. The mission of the FCVT program is to develop more energy efficient and environmentally friendly highway transportation technologies. Program activities include research, development, demonstration, testing, technology validation, and technology transfer. These activities are aimed at developing technologies that can be domestically produced in a clean and cost-competitive manner. Under the FCVT program, support is provided through a three-phase approach [1] which is intended to: • Identify overall propulsion and vehicle-related needs by analyzing programmatic goals and reviewing industry’s recommendations and requirements, then develop the appropriate technical targets for systems, subsystems, and component research and development activities; • Develop and validate individual subsystems and components, including electric motors, emission control devices, battery systems, power electronics, accessories, and devices to reduce parasitic losses; and • Determine how well the components and subassemblies work together in a vehicle environment or as a complete propulsion system and whether the efficiency and performance targets at the vehicle level have been achieved. The research performed in this area will help remove technical and cost barriers to enable technology for use in such advanced vehicles as hybrid electric, plug-in hybrid electric, electric, and fuel-cell-powered vehicles.

Burress, T.A.; Coomer, C.L.; Campbell, S.L.; Seiber, L.E.; Marlino, L.D.; Staunton, R.H.; Cunningham, J.P.

2008-04-15T23:59:59.000Z

46

CO{sub 2} Laser Ablation Propulsion Tractor Beams  

SciTech Connect

Manipulation of objects at a distance has already been achieved with no small measure of success in the realm of microscopic objects on the scale size of nanometers to micrometers in applications including laser trapping and laser tweezers. However, there has been relatively little effort to apply such remote control to macroscopic systems. A space tractor beam could be applied to a wide range of applications, including removal of orbital debris, facilitation of spacecraft docking, adjustment of satellite attitude or orbital position, etc. In this paper, an ablative laser propulsion tractor beam is demonstrated based on radiation from a CO{sub 2} laser. Cooperative, layered polymer targets were used for remote impulse generation using a CO{sub 2} laser. The use of a structured ablatant enabling switching between thrust directional parity (i.e., forward or reverse) and imparting torque to a remote target. Fluence-dependent results are presented in the context of polymer ablation modeling work and with consideration of confined ablation effects.

Sinko, John E. [Micro-Nano Global Center of Excellence, Graduate School of Engineering, Nagoya University, Furo-cho, Chikusa-ku, Nagoya, 464-8603 (Japan); Schlecht, Clifford A. [Institute for Materials and Complexity, Saint Louis, MO 63112 (United States)

2010-05-06T23:59:59.000Z

47

Evaluation of the 2010 Toyota Prius Hybrid Synergy Drive System  

DOE Green Energy (OSTI)

Subsystems of the 2010 Toyota Prius hybrid electric vehicle (HEV) were studied and tested as part of an intensive benchmarking effort carried out to produce detailed information concerning the current state of nondomestic alternative vehicle technologies. Feedback provided by benchmarking efforts is particularly useful to partners of the Vehicle Technologies collaborative research program as it is essential in establishing reasonable yet challenging programmatic goals which facilitate development of competitive technologies. The competitive nature set forth by the Vehicle Technologies Program (VTP) not only promotes energy independence and economic stability, it also advocates the advancement of alternative vehicle technologies in an overall global perspective. These technologies greatly facilitate the potential to reduce dependency on depleting natural resources and mitigate harmful impacts of transportation upon the environment.

Burress, Timothy A [ORNL; Campbell, Steven L [ORNL; Coomer, Chester [ORNL; Ayers, Curtis William [ORNL; Wereszczak, Andrew A [ORNL; Cunningham, Joseph Philip [ORNL; Marlino, Laura D [ORNL; Seiber, Larry Eugene [ORNL; Lin, Hua-Tay [ORNL

2011-03-01T23:59:59.000Z

48

Evaluation of 2005 Honda Accord Hybrid Electric Drive System  

DOE Green Energy (OSTI)

The Hybrid Electric Vehicle (HEV) program officially began in 1993 as a five-year, cost-shared partnership between the U.S. Department of Energy (DOE) and American auto manufacturers: General Motors, Ford, and Daimler Chrysler. Currently, HEV research and development is conducted by DOE through its FreedomCAR and Vehicle Technologies (FCVT) program. The mission of the FCVT program is to develop more energy efficient and environmentally friendly highway transportation technologies. Program activities include research, development, demonstration, testing, technology validation, and technology transfer. These activities are aimed at developing technologies that can be domestically produced in a clean and cost-competitive manner. The vehicle systems technologies subprogram, which is one of four subprograms under the FCVT program, supports the efforts of the FreedomCAR through a three-phase approach [1] intended to: (1) Identify overall propulsion and vehicle-related needs by analyzing programmatic goals and reviewing industry's recommendations and requirements, then develop the appropriate technical targets for systems, subsystems, and component research and development activities; (2) Develop and validate individual subsystems and components, including electric motors, emission control devices, battery systems, power electronics, accessories, and devices to reduce parasitic losses; and (3) Determine how well the components and subassemblies work together in a vehicle environment or as a complete propulsion system and whether the efficiency and performance targets at the vehicle level have been achieved. The research performed under the vehicle systems subprogram will help remove technical and cost barriers to enable technology for use in such advanced vehicles as hybrid electric, plug-in electric, and fuel-cell-powered vehicles.

Staunton, R.H.; Burress, T.A.; Marlino, L.D.

2006-09-11T23:59:59.000Z

49

Using LNG as a Fuel in Heavy-Duty Tractors  

DOE Green Energy (OSTI)

Recognizing the lack of operational data on alternative fuel heavy-truck trucks, NREL contracted with the Trucking Research Institute (TRI) in 1994 to obtain a cooperative agreement with Liquid Carbonic. The purpose of this agreement was to (1) purchase and operate liquid natural gas- (LNG-) powered heavy-duty tractor-trailers with prototype Detroit Diesel Corporation (DDC) Series 60 natural gas (S60G) engines in over-the-road commercial service applications; and (2) collect and provide operational data to DDC to facilitate the on-road prototype development of the engine and to NREL for the Alternative Fuels Data Center. The vehicles operated from August 1994 through April of 1997 and led to a commercially available, emissions-certified S60G in 1998. This report briefly documents the engine development, the operational characteristics of LNG, and the lessons learned during the project.

Liquid Carbonic, Inc. and Trucking Research Institute

1999-08-09T23:59:59.000Z

50

eGSE America Electric Baggage Tow Tractor (EBTT) Technical Specificati...  

NLE Websites -- All DOE Office Websites (Extended Search)

9204 1.0 SCOPE: This document outlines the design and performance requirements for a battery- powered electric tow tractor for the handling of baggage or cargo trailers in...

51

New York City Transit Hybrid and CNG Transit Buses: Interim Evaluation Results  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

New York City Transit Hybrid New York City Transit Hybrid and CNG Transit Buses: Interim Evaluation Results K. Chandler and E. Eberts Battelle L. Eudy National Renewable Energy Laboratory Technical Report NREL/TP-540-38843 January 2006 New York City Transit Hybrid and CNG Transit Buses: Interim Evaluation Results K. Chandler and E. Eberts Battelle L. Eudy National Renewable Energy Laboratory Prepared under Task No. FC06.3000 Technical Report NREL/TP-540-38843 January 2006 National Renewable Energy Laboratory 1617 Cole Boulevard, Golden, Colorado 80401-3393 303-275-3000 * www.nrel.gov Operated for the U.S. Department of Energy Office of Energy Efficiency and Renewable Energy by Midwest Research Institute * Battelle Contract No. DE-AC36-99-GO10337 NOTICE This report was prepared as an account of work sponsored by an agency of the United States government.

52

Design and Performance Evaluation of an Hybrid Reservation-Polling MAC Protocol for Power-Line  

E-Print Network (OSTI)

Units) in a low-voltage power grid, share the transmission capacity of the power-line network. To make of data. Since wires exist to every household connected to the low-voltage grid, PLC systems can provideDesign and Performance Evaluation of an Hybrid Reservation-Polling MAC Protocol for Power-Line

Tinnirello, Ilenia

53

Eighteen-Month Final Evaluation of UPS Second Generation Diesel Hybrid Electric Delivery Vans  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Eighteen-Month Final Evaluation Eighteen-Month Final Evaluation of UPS Second Generation Diesel Hybrid-Electric Delivery Vans M. Lammert and K. Walkowicz National Renewable Energy Laboratory Technical Report NREL/TP-5400-55658 September 2012 NREL is a national laboratory of the U.S. Department of Energy, Office of Energy Efficiency & Renewable Energy, operated by the Alliance for Sustainable Energy, LLC. National Renewable Energy Laboratory 15013 Denver West Parkway Golden, Colorado 80401 303-275-3000 * www.nrel.gov Contract No. DE-AC36-08GO28308 Eighteen-Month Final Evaluation of UPS Second Generation Diesel Hybrid-Electric Delivery Vans M. Lammert and K. Walkowicz National Renewable Energy Laboratory Prepared under Task No. FC08.3000 Technical Report

54

Evaluation of Emerging Battery Technologies for Plug-in Hybrid Vehicles  

Science Conference Proceedings (OSTI)

The performance, cycle life, and cost of available batteries are key issues in determining the marketability of plug-in hybrid-electric vehicles (PHEVs). The California Air Resources Board (CARB) initiated a project to evaluate emerging lithiumion battery technologies for PHEV applications. Work initially focused on the determination of the characteristics of one of the most interesting of the emerging lithium-ion batteries, the lithium titanate battery in commercial development by Altairnano, but other ...

2009-08-24T23:59:59.000Z

55

Economic evaluation of solar-only and hybrid power towers using molten salt technology  

DOE Green Energy (OSTI)

Several hybrid and solar-only configurations for molten-salt power towers were evaluated with a simple economic model, appropriate for screening analysis. The solar specific aspects of these plants were highlighted. In general, hybrid power towers were shown to be economically superior to solar-only plants with the same field size. Furthermore, the power-booster hybrid approach was generally preferred over the fuel-saver hybrid approach. Using today`s power tower technology, economic viability for the solar power-boost occurs at fuel costs in the neighborhood of $2.60/MBtu to $4.40/ MBtu (low heating value) depending on whether coal-based or gas-turbine-based technology is being offset. The cost Of CO[sub 2] avoidance was also calculated for solar cases in which the fossil fuel cost was too low for solar to be economically viable. The avoidance costs are competitive with other proposed methods of removing CO[sub 2] from fossil-fired power plants.

Kolb, G.J.

1996-12-01T23:59:59.000Z

56

Evaluation of Orion/BAE Hybrid Buses and Orion CNG Buses at New York City Transit: Preprint  

DOE Green Energy (OSTI)

This paper prepared for the 2005 American Public Transportation Association Bus & Paratransit Conference discusses the NREL/DOE evaluation of hybrid electric transit buses operated by New York City Transit.

Eudy, L.; Barnitt, R.; Chandler, K.

2005-05-01T23:59:59.000Z

57

Evaluation of 2004 Toyota Prius Hybrid Electric Drive System Interim Report  

SciTech Connect

Laboratory tests were conducted to evaluate the electrical and mechanical performance of the 2004 Toyota Prius and its hybrid electric drive system. As a hybrid vehicle, the 2004 Prius uses both a gasoline-powered internal combustion engine and a battery-powered electric motor as motive power sources. Innovative algorithms for combining these two power sources results in improved fuel efficiency and reduced emissions compared to traditional automobiles. Initial objectives of the laboratory tests were to measure motor and generator back-electromotive force (emf) voltages and determine gearbox-related power losses over a specified range of shaft speeds and lubricating oil temperatures. Follow-on work will involve additional performance testing of the motor, generator, and inverter. Information contained in this interim report summarizes the test results obtained to date, describes preliminary conclusions and findings, and identifies additional areas for further study.

Ayers, C.W.

2004-11-23T23:59:59.000Z

58

Testing and Evaluation of Batteries for a Fuel Cell Powered Hybrid Bus  

SciTech Connect

Argonne National Laboratory conducted performance characterization and life-cycle tests on various batteries to qualify them for use in a fuel cell/battery hybrid bus. On this bus, methanol-fueled, phosphoric acid fuel cells provide routine power needs, while batteries are used to store energy recovered during bus braking and to produce short-duration power during acceleration. Argonne carried out evaluation and endurance testing on several lead-acid and nickel/cadmium batteries selected by the bus developer as potential candidates for the bus application. Argonne conducted over 10,000 hours of testing, simulating more than 80,000 miles of fuel cell bus operation, for the nickel/cadmium battery, which was ultimately selected for use in the three hybrid buses built under the direction of H-Power Corp.

Miller, J.F.; Webster, C.E.; Tummillo, A.F.; DeLuca, W.H.

1997-05-01T23:59:59.000Z

59

Plug-in Hybrid Electric Vehicle Evaluation and Test Data Analysis  

Science Conference Proceedings (OSTI)

In 2003, EPRI and DaimlerChrysler initiated a three-part collaborative effort to 1) develop and demonstrate a plug-in hybrid electric vehicle (PHEV) based on the Sprinter vehicle platform, 2) deliver prototype Sprinter PHEVs to fleets within the United States, and 3) explore these benefits in the context of commercial fleet use. As part of this effort, EPRI assumed the responsibility of managing data acquisition and analysis. This report focuses on evaluation of the PHEV Sprinter tested by the South Coas...

2009-12-07T23:59:59.000Z

60

Study on Matching Strategies and Simulation of Hydro-mechanical Continuously Variable Transmission System of Tractor  

Science Conference Proceedings (OSTI)

In this paper, the engine output torque model and fuel consumption model are established based on engine test results. The engine rotary speed feature denotes the relationship between the engine rotary speed and the throttle opening when engine works ... Keywords: Tractor, Hydro-mechanical continuously variable transmission, Matching strategies, Simulation

Xu Liyou; Zhou Zhili; Cao Qingmei; Zhang Mingzhu

2010-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "hybrid tractor evaluation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Evaluation of amino acid supplementation of soybean-meal-based diets for hybrid striped bass  

E-Print Network (OSTI)

Hybrid striped bass (Morone chrysops x M. saxatilis) aquaculture is a major commercial enterprise in the United States and internationally. Efforts to decrease diet costs and limit dependence on fishmeal, have led to the development of plant-based diets as an alternative aquafeed. Due to limiting concentrations of amino acids such as methionine, cystine, and taurine in plant meals such as soybean meal, supplementation of these plant-based diets with methionine or other sulfur amino acid compounds is typically required. Therefore, the current study was conducted to evaluate different amino acid supplements in soybean-meal-based diets for hybrid striped bass for possible refinement of diets and reduction of production costs. One feeding trial evaluated methionine hydroxy analog (MHA) and Mintrex® which is MHA containing chelated zinc relative to L-methionine. The second trial evaluated the effects of supplemental taurine or arginine on fish performance and potential health benefits. In the first feeding trial, a basal soybean-meal-based diet (56% soybean meal and 15% fishmeal) marginally deficient in total sulfur amino acids (TSSA) (1.10% methionine and cystine) was supplemented with either L-methionine, Mintrex® or MHA calcium salt and fed to triplicate groups of juvenile hybrid striped bass for 10 weeks. The different methionine supplements provided similar weight gain, feed efficiency ratio (FER) and protein efficiency ratio (PER) values that tended to be greater than observed in fish fed the basal diet. Mintrex® supplementation provided much higher plasma zinc concentrations compared to fish fed the other methionine supplements. In the second feeding trial, soybean-meal based diets which satisfied the requirement for TSAA were supplemented with either taurine or arginine at 1.5% of dry weight. Supplemental taurine or arginine did not provide any improvements in weight gain, FER, PER or survival compared to the basal diet. Thus, taurine or arginine supplementation of soybean-meal-based diets does not appear warranted. However, sulfur amino acid supplementation of plant-based diets is critical, and Mintrex® appears to be an effective supplement to meet the methionine and zinc needs of hybrid striped bass.

Savolainen, Lea Christine

2008-12-01T23:59:59.000Z

62

FedEx Gasoline Hybrid Electric Delivery Truck Evaluation: 6-Month Interim Report  

SciTech Connect

This interim report presents partial (six months) results for a technology evaluation of gasoline hybrid electric parcel delivery trucks operated by FedEx in and around Los Angeles, CA. A 12 month in-use technology evaluation comparing in-use fuel economy and maintenance costs of GHEVs and comparative diesel parcel delivery trucks was started in April 2009. Comparison data was collected and analyzed for in-use fuel economy and fuel costs, maintenance costs, total operating costs, and vehicle uptime. In addition, this interim report presents results of parcel delivery drive cycle collection and analysis activities as well as emissions and fuel economy results of chassis dynamometer testing of a gHEV and a comparative diesel truck at the National Renewable Energy Laboratory's (NREL) ReFUEL laboratory. A final report will be issued when 12 months of in-use data have been collected and analyzed.

Barnitt, R.

2010-05-01T23:59:59.000Z

63

A Study in Sorghum Bicolor: QTL Analysis of Photoperiod Sensitive Sorghums, Evaluation of Sorghum x Sugarcane Hybrids and Trait Introgression for Intergeneric Hybrid Improvement  

E-Print Network (OSTI)

Recently designated as a bioenergy crop, Sorghum is rather unique as it can produce large quantities of cellulose or sugar which can be used to produce advanced biofuels or compounds. Sweet sorghum contains high levels of sugars and biomass sorghums consist primarily of ligno-cellulosic biomass. Improvement of both sorghum types is essential for maximizing production and conversion efficiency. Photoperiod sensitive sorghum is thought to maximize biomass production yet maturity influence on biomass production and composition is not fully understood. Utilizing sorghum for sugar production has increased efforts to develop sweet sorghums with sugar yields similar to sugarcane. Hybridization of these species has been investigated with, until recently, little success. Testing newly developed intergeneric hybrids and improvement of parents used in their creation will determine their feasibility and improve hybrid performance. Objectives of this research are multifaceted. First, analyze photoperiod sensitive sorghum in varying day length environments to determine maturity effects on plant phenotype, composition, and QTL detection. Second, analyze intergeneric sorghum × sugarcane hybrids to determine agronomic performance in relation to sugarcane. Lastly, introgress the iap allele into sweet sorghum females for use in intergeneric hybrid creation. Photoperiod sensitive sorghum RILs were evaluated in College Station and Weslaco, Texas and Puerto Rico which caused differential expression of plant maturity. Genetic control of trait expression was high for each location. Results indicate gradual induction of plant maturity increases detection of phenotypic QTL and detection of compositional QTL increases when maturity effects on plant phenotype are reduced. Intergeneric sorghum × sugarcane F_1 hybrids were compared to sugarcane in Weslaco, Texas in 2011. Each hybrid expressed agronomic traits similar or better than that of the sugarcane variety. High levels of repeatability and genetic influence on trait expression were observed. Overall performance of the sugarcane variety was better than any individual hybrid tested. Introgression of iap into sweet sorghum was successful and generated seventeen new sweet sorghum female genotypes possessing the allele. Only two genotypes exhibited higher brix readings and both were later maturing than Tx3361. Height and maturity of all developed genotypes varied and desirability of developed lines was similar to Tx3361.

Bartek, Matthew

2013-08-01T23:59:59.000Z

64

Evaluation of 2004 Toyota Prius Hybrid Electic Drive System Interim Report - Revised  

SciTech Connect

The 2004 Toyota Prius is a hybrid automobile equipped with a gasoline engine and a battery-powered electric motor. Both of these motive power sources are capable of providing mechanical drive power for the vehicle. The engine can deliver a peak power output of 57 kilowatts (kW) at 5000 revolutions per minute (rpm) while the motor can deliver a peak power output of 50 kW at 1300 rpm. Together, this engine-motor combination has a specified peak power output of 82 kW at a vehicle speed of 85 kilometers per hour (km/h). In operation, the 2004 Prius exhibits superior fuel economy compared to conventionally powered automobiles. Laboratory tests were conducted to evaluate the electrical and mechanical performance of the 2004 Toyota Prius and its hybrid electric drive system. As a hybrid vehicle, the 2004 Prius uses both a gasoline-powered internal combustion engine and a battery-powered electric motor as motive power sources. Innovative algorithms for combining these two power sources results in improved fuel efficiency and reduced emissions compared to traditional automobiles. Initial objectives of the laboratory tests were to measure motor and generator back-electromotive force (emf) voltages and determine gearbox-related power losses over a specified range of shaft speeds and lubricating oil temperatures. Follow-on work will involve additional performance testing of the motor, generator, and inverter. Information contained in this interim report summarizes the test results obtained to date, describes preliminary conclusions and findings, and identifies additional areas for further study.

Ayers, C.W.; Hsu, J.S.; Marlino, L.D.; Miller, C.W.; Ott, G.W., Jr.; Oland, C.B.; Burress, T.A.

2007-07-31T23:59:59.000Z

65

Twelve-Month Evaluation of UPS Diesel Hybrid Electric Delivery Vans  

DOE Green Energy (OSTI)

Results of an NREL study of a parallel hybrid electric-diesel propulsion system in United Parcel Service-operated delivery vans show that the hybrids had higher fuel economy than standard diesel vans.

Lammert, M.

2009-12-01T23:59:59.000Z

66

Plug-In Hybrid Electric Vehicle Value Proposition Study: Interim Report: Phase I Scenario Evaluation  

DOE Green Energy (OSTI)

Plug-in hybrid electric vehicles (PHEVs) offer significant improvements in fuel economy, convenient low-cost recharging capabilities, potential environmental benefits, and decreased reliance on imported petroleum. However, the cost associated with new components (e.g., advanced batteries) to be introduced in these vehicles will likely result in a price premium to the consumer. This study aims to overcome this market barrier by identifying and evaluating value propositions that will increase the qualitative value and/or decrease the overall cost of ownership relative to the competing conventional vehicles and hybrid electric vehicles (HEVs) of 2030 During this initial phase of this study, business scenarios were developed based on economic advantages that either increase the consumer value or reduce the consumer cost of PHEVs to assure a sustainable market that can thrive without the aid of state and Federal incentives or subsidies. Once the characteristics of a thriving PHEV market have been defined for this timeframe, market introduction steps, such as supportive policies, regulations and temporary incentives, needed to reach this level of sustainability will be determined. PHEVs have gained interest over the past decade for several reasons, including their high fuel economy, convenient low-cost recharging capabilities, potential environmental benefits and reduced use of imported petroleum, potentially contributing to President Bush's goal of a 20% reduction in gasoline use in ten years, or 'Twenty in Ten'. PHEVs and energy storage from advanced batteries have also been suggested as enabling technologies to improve the reliability and efficiency of the electric power grid. However, PHEVs will likely cost significantly more to purchase than conventional or other hybrid electric vehicles (HEVs), in large part because of the cost of batteries. Despite the potential long-term savings to consumers and value to stakeholders, the initial cost of PHEVs presents a major market barrier to their widespread commercialization. The purpose of this project is to identify and evaluate value-added propositions for PHEVs that will help overcome this market barrier. Candidate value propositions for the initial case study were chosen to enhance consumer acceptance of PHEVs and/or compatibility with the grid. Potential benefits of such grid-connected vehicles include the ability to supply peak load or emergency power requirements of the grid, enabling utilities to size their generation capacity and contingency resources at levels below peak. Different models for vehicle/battery ownership, leasing, financing and operation, as well as the grid, communications, and vehicle infrastructure needed to support the proposed value-added functions were explored during Phase 1. Rigorous power system, vehicle, financial and emissions modeling were utilized to help identify the most promising value propositions and market niches to focus PHEV deployment initiatives.

Sikes, Karen R [ORNL; Markel, Lawrence C [ORNL; Hadley, Stanton W [ORNL; Hinds, Shaun [Sentech, Inc.; DeVault, Robert C [ORNL

2009-01-01T23:59:59.000Z

67

A new antifouling hybrid CDP formulation with ethyl heptanoate: evaluation of AF performance at Ayajin harbor, east coast of Korea  

Science Conference Proceedings (OSTI)

Antifouling (AF) efficiency of a nontoxic aliphatic ester, ethyl heptanoate was evaluated against spores of a fouling alga Ulva pertusa and a ship fouling diatom Amphora coffeaeformis. Based on the nontoxic AF activity exhibited in the laboratory bioassays, ... Keywords: antifouling, ethyl heptanoate, fouling resistance, hybrid controlled depletion paint (CDP), zinc pyrithione

M. Sidharthan; Sang Mok Jung; Haridatta Bhatta Rai; Ji Hyun Lee; Chi Young Lim; Young-Kyu Kang; N. S. Park; H. W. Shin

2006-07-01T23:59:59.000Z

68

MARVEL: A PC-based interactive software package for life-cycle evaluations of hybrid/electric vehicles  

SciTech Connect

As a life-cycle analysis tool, MARVEL has been developed for the evaluation of hybrid/electric vehicle systems. It can identify the optimal combination of battery and heat engine characteristics for different vehicle types and performance requirements, on the basis of either life-cycle cost or fuel efficiency. Battery models that allow trade-offs between specific power and specific energy, between cycle life and depth of discharge, between peak power and depth of discharge, and between other parameters, are included in the software. A parallel hybrid configuration, using an internal combustion engine and a battery as the power sources, can be simulated with a user-specified energy management strategy. The PC-based software package can also be used for cost or fuel efficiency comparisons among conventional, electric, and hybrid vehicles.

Marr, W.W.; He, J.

1995-07-01T23:59:59.000Z

69

Plug-In Hybrid Electric Vehicle Value Proposition Study: Interim Report: Phase I Scenario Evaluation  

SciTech Connect

Plug-in hybrid electric vehicles (PHEVs) offer significant improvements in fuel economy, convenient low-cost recharging capabilities, potential environmental benefits, and decreased reliance on imported petroleum. However, the cost associated with new components (e.g., advanced batteries) to be introduced in these vehicles will likely result in a price premium to the consumer. This study aims to overcome this market barrier by identifying and evaluating value propositions that will increase the qualitative value and/or decrease the overall cost of ownership relative to the competing conventional vehicles and hybrid electric vehicles (HEVs) of 2030 During this initial phase of this study, business scenarios were developed based on economic advantages that either increase the consumer value or reduce the consumer cost of PHEVs to assure a sustainable market that can thrive without the aid of state and Federal incentives or subsidies. Once the characteristics of a thriving PHEV market have been defined for this timeframe, market introduction steps, such as supportive policies, regulations and temporary incentives, needed to reach this level of sustainability will be determined. PHEVs have gained interest over the past decade for several reasons, including their high fuel economy, convenient low-cost recharging capabilities, potential environmental benefits and reduced use of imported petroleum, potentially contributing to President Bush's goal of a 20% reduction in gasoline use in ten years, or 'Twenty in Ten'. PHEVs and energy storage from advanced batteries have also been suggested as enabling technologies to improve the reliability and efficiency of the electric power grid. However, PHEVs will likely cost significantly more to purchase than conventional or other hybrid electric vehicles (HEVs), in large part because of the cost of batteries. Despite the potential long-term savings to consumers and value to stakeholders, the initial cost of PHEVs presents a major market barrier to their widespread commercialization. The purpose of this project is to identify and evaluate value-added propositions for PHEVs that will help overcome this market barrier. Candidate value propositions for the initial case study were chosen to enhance consumer acceptance of PHEVs and/or compatibility with the grid. Potential benefits of such grid-connected vehicles include the ability to supply peak load or emergency power requirements of the grid, enabling utilities to size their generation capacity and contingency resources at levels below peak. Different models for vehicle/battery ownership, leasing, financing and operation, as well as the grid, communications, and vehicle infrastructure needed to support the proposed value-added functions were explored during Phase 1. Rigorous power system, vehicle, financial and emissions modeling were utilized to help identify the most promising value propositions and market niches to focus PHEV deployment initiatives.

Sikes, Karen R [ORNL; Markel, Lawrence C [ORNL; Hadley, Stanton W [ORNL; Hinds, Shaun [Sentech, Inc.; DeVault, Robert C [ORNL

2009-01-01T23:59:59.000Z

70

Determination of influence factors and accident rates for the Armored Tractor/Safe Secure Trailer  

Science Conference Proceedings (OSTI)

Operating environments, such as road type, road location, and time of day, play an important role in the observed accident rates of heavy trucks used in general commerce. These same factors influence the accident rate of the Armored Tractor/Safe Secure Trailer (AT/SST) used by the Department of Energy to transport hazardous cargos within the continental United States. This report discusses the development of accident rate influence factors. These factors, based on heavy trucks used in general commerce, are used to modify the observed overall AT/SST accident rate to account for the different operating environments.

Phillips, J.S.; Clauss, D.B. [Sandia National Labs., Albuquerque, NM (United States); Blower, D.F. [Univ. of Michigan Transportation Research Institute, Ann Arbor, MI (United States). Center for National Truck Statistics

1994-04-01T23:59:59.000Z

71

Structural dynamics modeling and testing of the Department of Energy tractor/trailer combination  

DOE Green Energy (OSTI)

This study presents a combined analytical and experimental effort to characterize and improve the ride quality of the Department of Energy tractor/trailer combination. The focus is to augment the experimental test results with the use of a high quality computer model. The discussion includes an overview of the finite element model of the vehicle and experimental modal test results. System identification techniques are employed to update the mathematical model. The validated model is then used to illustrate the benefits of incorporating two major design changes, namely the switch from a separate cab/sleeper configuration to an integrated cab, and the use of a cab suspension system.

Field, R.V. Jr.; Hurtado, J.E.; Carne, T.G.; Dohrmann, C.R.

1996-12-31T23:59:59.000Z

72

Technical Description and Evaluation of BWR Hybrid Power Shape Monitoring System  

Science Conference Proceedings (OSTI)

This report discusses the method of monitoring BWR cores that has been implemented in the Power Shape Monitoring System (PSMS). A complete technical description of the hybrid PSMS and the results of detailed qualification testing are included.

1982-03-01T23:59:59.000Z

73

New York City Transit Hybrid and CNG Transit Buses: Interim Evaluation...  

NLE Websites -- All DOE Office Websites (Extended Search)

CA Peterbilt378, Class 8 truck Cummins Westport ISXG high pressure direct injection LNG and diesel Complete and reported IndyGo Indianapolis, IN Ebus 22-ft bus Series hybrid,...

74

Thirty-Six Month Evaluation of UPS Diesel Hybrid Electric Delivery...  

NLE Websites -- All DOE Office Websites (Extended Search)

CO Gillig 40-ft transit bus Biodiesel blend (B20) Completed in October 2006 King County Metro Seattle, WA New Flyer 60-ft articulated transit bus Parallel hybrid, GM-Allison...

75

Test Profile Development for the Evaluation of Battery Cycle Life for Plug-In Hybrid Electric Vehicles  

Science Conference Proceedings (OSTI)

EPRI and DaimlerChrysler have developed a plug-in hybrid electric vehicle (PHEV) concept for the DaimlerChrysler Sprinter Van in an effort to reduce the emissions, fuel consumption, and operating costs of the vehicle while maintaining equivalent or superior functionality and performance. This report describes the development of a test profile to evaluate the life cycle of the batteries for the PHEV vehicle.

2004-03-29T23:59:59.000Z

76

Long Beach Transit: Two-Year Evaluation of Gasoline-Electric Hybrid Transit Buses  

DOE Green Energy (OSTI)

This report focuses on a gasoline-electric hybrid transit bus propulsion system. The propulsion system is an alternative to standard diesel buses and allows for reductions in emissions (usually focused on reductions of particulate matter and oxides of nitrogen) and petroleum use. Gasoline propulsion is an alternative to diesel fuel and hybrid propulsion allows for increased fuel economy, which ultimately results in reduced petroleum use.

Lammert, M.

2008-06-01T23:59:59.000Z

77

Evaluation of Utility System Impacts and Benefits of Optimally Dispatched Plug-In Hybrid Electric Vehicles (Revised)  

SciTech Connect

Hybrid electric vehicles with the capability of being recharged from the grid may provide a significant decrease in oil consumption. These ''plug-in'' hybrids (PHEVs) will affect utility operations, adding additional electricity demand. Because many individual vehicles may be charged in the extended overnight period, and because the cost of wireless communication has decreased, there is a unique opportunity for utilities to directly control the charging of these vehicles at the precise times when normal electricity demand is at a minimum. This report evaluates the effects of optimal PHEV charging, under the assumption that utilities will indirectly or directly control when charging takes place, providing consumers with the absolute lowest cost of driving energy. By using low-cost off-peak electricity, PHEVs owners could purchase the drive energy equivalent to a gallon of gasoline for under 75 cents, assuming current national average residential electricity prices.

Denholm, P.; Short, W.

2006-10-01T23:59:59.000Z

78

Evaluation of Utility System Impacts and Benefits of Optimally Dispatched Plug-In Hybrid Electric Vehicles (Revised)  

DOE Green Energy (OSTI)

Hybrid electric vehicles with the capability of being recharged from the grid may provide a significant decrease in oil consumption. These ''plug-in'' hybrids (PHEVs) will affect utility operations, adding additional electricity demand. Because many individual vehicles may be charged in the extended overnight period, and because the cost of wireless communication has decreased, there is a unique opportunity for utilities to directly control the charging of these vehicles at the precise times when normal electricity demand is at a minimum. This report evaluates the effects of optimal PHEV charging, under the assumption that utilities will indirectly or directly control when charging takes place, providing consumers with the absolute lowest cost of driving energy. By using low-cost off-peak electricity, PHEVs owners could purchase the drive energy equivalent to a gallon of gasoline for under 75 cents, assuming current national average residential electricity prices.

Denholm, P.; Short, W.

2006-10-01T23:59:59.000Z

79

FedEx Express Gasoline Hybrid Electric Delivery Truck Evaluation: 12-Month Report  

DOE Green Energy (OSTI)

This report summarizes the data obtained in a 12-month comparison of three gasoline hybrid electric delivery vehicles with three comparable diesel vehicles. The data show that there was no statistical difference between operating cost per mile of the two groups of vehicles. As expected, tailpipe emissions were considerably lower across all drive cycles for the gHEV than for the diesel vehicle.

Barnitt, R.

2011-01-01T23:59:59.000Z

80

Design and evaluation of a hybrid sensor network for cane toad monitoring  

Science Conference Proceedings (OSTI)

This article investigates a wireless acoustic sensor network application—monitoring amphibian populations in the monsoonal woodlands of northern Australia. Our goal is to use automatic recognition of animal vocalizations to census the populations ... Keywords: Sensor networks, acoustic, application, high frequency sampling, hybrid, solar energy

Wen Hu; Nirupama Bulusu; Chun Tung Chou; Sanjay Jha; Andrew Taylor; Van Nghia Tran

2009-02-01T23:59:59.000Z

Note: This page contains sample records for the topic "hybrid tractor evaluation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Hybrid models in decision making under uncertainty: The case of training provider evaluation  

Science Conference Proceedings (OSTI)

This paper provides a novel design for two hybrid models in modeling decision making under uncertainty: AHP-Fuzzy PROMETHEE and AHP-Fuzzy TOPSIS. The analytic hierarchy process' (AHP) excellent ability in problem structuring allows weights of criteria ... Keywords: AHP, PROMETHEE, TOPSIS, decision analysis, fuzzy MCDM, service outsourcing

J. Ignatius; S. M. H. Motlagh; M. M. Sepehri; M. Behzadian; A. Mustafa

2010-04-01T23:59:59.000Z

82

The U.S. Department of Energy's (DOE's) FreedomCAR and Vehicle Technologies (FCVT) Program is actively evaluating plug-in hybrid electric vehicle (PHEV) technology and researching the most critical technical barriers to  

E-Print Network (OSTI)

for use in hybrid vehicles as well as electric-only vehicles · Hardware-in-the-loop evaluation of advanced is actively evaluating plug-in hybrid electric vehicle (PHEV) technology and researching the most critical and capacitor scaling, thermal management, capacity, and power fade · Using hybrid electric vehicles in fleets

Kemner, Ken

83

A Vehicle Systems Approach to Evaluate Plug-in Hybrid Battery Cold Start, Life and Cost Issues  

E-Print Network (OSTI)

The batteries used in plug-in hybrid electric vehicles (PHEVs) need to overcome significant technical challenges in order for PHEVs to become economically viable and have a large market penetration. The internship at Argonne National Laboratory (ANL) involved two experiments which looked at a vehicle systems approach to analyze two such technical challenges: Battery life and low battery power at cold (-7 ?C) temperature. The first experiment, concerning battery life and its impact on gasoline savings due to a PHEV, evaluates different vehicle control strategies over a pre-defined vehicle drive cycle, in order to identify the control strategy which yields the maximum dollar savings (operating cost) over the life of the vehicle, when compared to a charge sustaining hybrid. Battery life degradation over the life of the vehicle, and fuel economy savings on every trip (daily) are taken into account when calculating the net present value of the gasoline dollars saved. The second experiment evaluates the impact of different vehicle control strategies in heating up the PHEV battery (due to internal ohmic losses) for cold ambient conditions. The impact of low battery power (available to the vehicle powertrain) due to low battery and ambient temperatures has been well documented in literature. The trade-off between the benefits of heating up the battery versus heating up the internal combustion engine are evaluated, using different control strategies, and the control strategy, which provided optimum temperature rise of each component, is identified.

Shidore, Neeraj Shripad

2012-05-01T23:59:59.000Z

84

A hybrid vehicle evaluation code and its application to vehicle design  

DOE Green Energy (OSTI)

This report describes a hybrid vehicle simulation model, which can be applied to many of the vehicles currently being considered for low pollution and high fuel economy. The code operates interactively, with all the vehicle information stored in data files. The code calculates fuel economy for three driving schedules, time for 0-96 km/h at maximum acceleration, hill climbing performance, power train dimensions, and pollution generation rates. This report also documents the application of the code to a hybrid vehicle that operates with a hydrogen internal combustion engine. The simulation model is used for parametric studies of the vehicle. The results show the fuel economy of the vehicle as a function of vehicle mass, aerodynamic drag, engine-generator efficiency, flywheel efficiency, and flywheel energy and power capacities.

Aceves, S.M.; Smith, J.R.

1994-07-15T23:59:59.000Z

85

Plug-in Hybrid Electric Vehicle (PHEV) Prototype Testing and Evaluation -- Data Collection and Analysis  

Science Conference Proceedings (OSTI)

In 2003, EPRI and DaimlerChrysler initiated a collaborative effort to develop and demonstrate a Plug-in Hybrid Electric Vehicle (PHEV) version of DaimlerChrysler's Sprinter commercial van. PHEV Sprinters were subsequently developed and used in limited fleet testing at several locations within the United States. As part of this effort, EPRI took on the responsibility of managing data acquisition and analysis. This report describes the data analysis toolkit EPRI created as part of an ongoing effort to eval...

2008-12-16T23:59:59.000Z

86

A hybrid vehicle evaluation code and its application to vehicle design. Revision 2  

DOE Green Energy (OSTI)

This paper describes a hybrid vehicle simulation model which can be applied to many of the vehicles currently being considered for low pollution and high fuel economy. The code operates in batch mode with all the vehicle information stored in data files. The code calculates power train dimensions, fuel economy for three driving schedules, time for 0-96 km/h at maximum acceleration, hill climbing performance, and pollution generation rates. This paper also documents the application of the code to a hybrid vehicle that utilizes a hydrogen internal combustion engine. The simulation model is used for parametric studies of the vehicle. The results show the fuel economy of the vehicle as a function of vehicle mass, aerodynamic drag, engine efficiency, accessory load, and flywheel efficiency. The code also calculates the minimum flywheel energy and power to obtain a desired performance. The hydrogen hybrid vehicle analyzed in the paper has a range of 480 km (300 miles), with a predicted gasoline equivalent fuel efficiency of 33.7 km/liter (79.3 mpg).

Aceves, S.M.; Smith, J.R.

1994-12-13T23:59:59.000Z

87

A hybrid vehicle evaluation code and its application to vehicle design. Revision 1  

DOE Green Energy (OSTI)

This paper describes a hybrid vehicle simulation model which can be applied to many of the vehicles currently being considered for low pollution and high fuel economy. The code operates in batch mode with all the vehicle information stored in data files. The code calculates fuel economy for three driving schedules, time for 0--96 km/h at maximum acceleration, hill climbing performance, power train dimensions, and pollution generation rates. This paper also documents the application of the code to a hybrid vehicle that utilizes a hydrogen internal combustion engine. The simulation model is used for parametric studies of the vehicle. The results show the fuel economy of the vehicle as a function of vehicle mass, aerodynamic drag, engine efficiency, accessory load, and flywheel efficiency. The code also calculates the minimum flywheel energy and power to obtain a desired performance. The hydrogen hybrid vehicle analyzed in the paper has a predicted range of 480 km (300 miles), with a gasoline equivalent fuel efficiency of 34.2 km/liter (80.9 mpg).

Aceves, S.M.; Smith, J.R.

1994-09-15T23:59:59.000Z

88

A Preliminary Evaluation of Alternative Liquid Desiccants for a Hybrid Desiccant Air Conditioner  

E-Print Network (OSTI)

This paper presents the results of a preliminary investigation at The University of Texas at Austin of alternative liquid desiccants for use in a hybrid desiccant air-conditioning system in which a desiccant is circulated between the evaporator and the condenser of a vapor-compression air conditioner. The liquid desiccants studied were lithium chloride, lithium bromide, calcium chloride, and triethylene glycol. Each candidate desiccant was subjected to a screening process which weighed the merits of the desiccant in terms of selected characteristics. The best liquid desiccant for the anticipated application was found to be calcium chloride.

Studak, J. W.; Peterson, J. L.

1988-01-01T23:59:59.000Z

89

Evaluation of the 2008 Lexus LS 600H Hybrid Synergy Drive System  

Science Conference Proceedings (OSTI)

Subsystems of the 2008 Lexus 600h hybrid electric vehicle (HEV) were studied and tested as part of an intensive benchmarking effort carried out to produce detailed information concerning the current state of nondomestic alternative vehicle technologies. Feedback provided by benchmarking efforts is particularly useful to partners of the Vehicle Technologies collaborative research program as it is essential in establishing reasonable yet challenging programmatic goals which facilitate development of competitive technologies. The competitive nature set forth by the Vehicle Technologies program not only promotes energy independence and economic stability, it also advocates the advancement of alternative vehicle technologies in an overall global perspective. These technologies greatly facilitate the potential to reduce dependency on depleting natural resources and mitigate harmful impacts of transportation upon the environment.

Burress, T.A.; Coomer, C.L.; Campbell, S.L.; Wereszczak, A.A.; Cunningham, J.P.; Marlino, L.D.; Seiber, L.E.; Lin, H.T.

2009-01-15T23:59:59.000Z

90

Heavy and Overweight Vehicle Brake Testing: Five-Axle Combination Tractor-Flatbed Final Report  

Science Conference Proceedings (OSTI)

The Federal Motor Carrier Safety Administration, in coordination with the Federal Highway Administration, sponsored the Heavy and Overweight Vehicle Brake Testing (HOVBT) program in order to provide information about the effect of gross vehicle weight (GVW) on braking performance. Because the Federal Motor Carrier Safety Regulations limit the number of braking system defects that may exist for a vehicle to be allowed to operate on the roadways, the examination of the effect of brake defects on brake performance for increased loads is also relevant. The HOVBT program seeks to provide relevant information to policy makers responsible for establishing load limits, beginning with providing test data for a combination tractor/trailer. This testing was conducted on a five-axle combination vehicle with tractor brakes meeting the Reduced Stopping Distance requirement rulemaking. This report provides a summary of the testing activities, the results of various analyses of the data, and recommendations for future research. Following a complete brake rebuild, instrumentation, and brake burnish, stopping tests were performed from 20 and 40 mph with various brake application pressures (15 psi, 25 psi, 35 psi, 45 psi, 55 psi, and full system pressure). These tests were conducted for various brake conditions at the following GVWs: 60,000, 80,000, 91,000, 97,000, 106,000, and 116,000 lb. The 80,000-lb GVWs included both balanced and unbalanced loads. The condition of the braking system was also varied. To introduce these defects, brakes (none, forward drive axle, or rear trailer axle) were made inoperative. In addition to the stopping tests, performance-based brake tests were conducted for the various loading and brake conditions. Analysis of the stopping test data showed the stopping distance to increase with load (as expected) and also showed that more braking force was generated by the drive axle brakes than the trailer axle brakes. The constant-pressure stopping test data revealed a linear relationship between brake application pressure and was used to develop an algorithm to normalize stopping data for weight and initial speed.

Lascurain, Mary Beth [ORNL] ORNL; Capps, Gary J [ORNL] ORNL; Franzese, Oscar [ORNL] ORNL

2013-10-01T23:59:59.000Z

91

MODEL AND ALGORITHM EVALUATION FOR THE HYBRID UF6 CONTAINER INSPECTION SYSTEM  

Science Conference Proceedings (OSTI)

ABSTRACT Pacific Northwest National Laboratory (PNNL) is developing an automated UF6 cylinder verification station concept based on the combined collection of traditional enrichment-meter (186 keV photons from U-235) data and non-traditional, neutron-induced, high-energy gamma-signatures (3-8.5 MeV) with an array of collimated, medium-resolution scintillators. Previous (2010) work at PNNL demonstrated proof-of-principle that this hybrid method yields accurate, full-volume assay of the cylinder enrichment, reduces systematic errors when compared to several other enrichment assay methods, and provides simplified instrumentation and algorithms suitable for long-term unattended operations. We used Monte Carlo modeling with MCNP5 to support system design (e.g., number and configuration of detector arrays, and design of iron/poly collimators for enhanced (n,?) conversion) and enrichment algorithm development. We developed a first-generation modeling framework in 2010. These tools have since been expanded, refined and benchmarked against field measurements with a prototype system of a 30B cylinder population (0.2 to 4.95 weight % U-235). The MCNP5 model decomposes the radiation transport problem into a linear superposition of “basis spectra” representing contributions from the different uranium isotopes and gamma-ray generation mechanisms (e.g. neutron capture). This scheme accommodates fast generation of “virtual assay signatures” for arbitrary enrichment, material age, and fill variations. Ongoing (FY-2011) refinements to the physics model include accounting for generation of bremsstrahlung photons, arising primarily from the beta decay of Pa-234m, a U-238 daughter. We are using the refined model to optimize collimator design for the hybrid method. The traditional assay method benefits from a high degree of collimation (to isolate each detector’s field-of-view) and relatively small detector area, while the non-traditional method benefits from a wide field-of-view, i.e. less collimation and larger detectors. We implement the enrichment-meter method by applying a square-wave digital filter to a raw spectrum and extracting the 186-keV peak area directly from the convolute spectrum. Ongoing enhancements to this approach include mitigating a systematic peak-area measurement deficit arising from curvature in the spectrum continuum shape. An optimized system prototype based on model results is utilized in a new set of 2011 field measurements, and model and measurement enrichment assay uncertainties are compared.

McDonald, Benjamin S.; Jordan, David V.; Orton, Christopher R.; Mace, Emily K.; Smith, Leon E.; Wittman, Richard S.

2011-06-14T23:59:59.000Z

92

Status and evaluation of hybrid electric vehicle batteries for short term applications. Final report  

SciTech Connect

The objective of this task is to compile information regarding batteries which could be use for electric cars or hybrid vehicles in the short term. More specifically, this study applies lead-acid batteries and nickel-cadmium battery technologies which are more developed than the advanced batteries which are presently being investigated under USABC contracts and therefore more accessible in production efficiency and economies of scale. Moreover, the development of these batteries has advanced the state-of-the-art not only in terms of performance and energy density but also in cost reduction. The survey of lead-acid battery development took the biggest part of the effort, since they are considered more apt to be used in the short-term. Companies pursuing the advancement of lead-acid batteries were not necessarily the major automobile battery manufacturers. Innovation is found more in small or new companies. Other battery systems for short-term are discussed in the last part of this report. We will review the various technologies investigated, their status and prognosis for success in the short term.

Himy, A. [Westinghouse Electric Co., Pittsburgh, PA (United States). Machinery Technology Div.

1995-07-01T23:59:59.000Z

93

Hybrid Car Calculator | Open Energy Information  

Open Energy Info (EERE)

Hybrid Car Calculator Jump to: navigation, search Tool Summary Name: Hybrid Car Calculator AgencyCompany Organization: New American Dream Phase: "Evaluate Options and Determine...

94

EVALUATION OF FLAT-PLATE PHOTOVOLTAIC THERMAL HYBRID SYSTEMS FOR SOLAR ENERGY UTILIZATION.  

DOE Green Energy (OSTI)

The technical and economic attractiveness of combined photovoltaic/thermal (PV/T) solar energy collectors was evaluated. The study was limited to flat-plate collectors since concentrating photovoltaic collectors require active cooling and thus are inherently PV/T collectors, the only decision being whether to use the thermal energy or to dump it. it was also specified at the outset that reduction in required roof area was not to be used as an argument for combining the collection of thermal and electrical energy into one module. Three tests of economic viability were identified, all of which PV/T must pass if it is to be considered a promising alternative: PV/T must prove to be competitive with photovoltaic-only, thermal-only, and side-by-side photovoltaic-plus-thermal collectors and systems. These three tests were applied to systems using low-temperature (unglazed) collectors and to systems using medium-temperature (glazed) collectors in Los Angeles, New York, and Tampa. For photovoltaics, the 1986 DOE cost goals were assumed to have been realized, and for thermal energy collection two technologies were considered: a current technology based on metal and glass, and a future technology based on thin-film plastics. The study showed that for medium-temperature applications PV/T is not an attractive option in any of the locations studied. For low-temperature applications, PV/T appears to be marginally attractive.

ANDREWS,J.W.

1981-06-01T23:59:59.000Z

95

Systematic evaluation of four-dimensional hybrid depth scanning for carbon-ion lung therapy  

Science Conference Proceedings (OSTI)

Purpose: Irradiation of a moving target with a scanning beam requires a comprehensive understanding of organ motion as well as a robust dose error mitigation technique. The authors studied the effects of intrafractional respiratory motion for carbon-ion pencil beam scanning with phase-controlled rescanning on dose distributions for lung tumors. To address density variations, they used 4DCT data. Methods: Dose distributions for various rescanning methods, such as simple layer rescanning (LR), volumetric rescanning, and phase-controlled rescanning (PCR), were calculated for a lung phantom and a lung patient studies. To ensure realism, they set the scanning parameters such as scanning velocity and energy variation time to be similar to those used at our institution. Evaluation metrics were determined with regard to clinical relevance, and consisted of (i) phase-controlled rescanning, (ii) sweep direction, (iii) target motion (direction and amplitude), (iv) respiratory cycle, and (v) prescribed dose. Spot weight maps were calculated by using a beam field-specific target volume, which takes account of range variations for respective respiratory phases. To emphasize the impact of intrafractional motion on the dose distribution, respiratory gating was not used. The accumulated dose was calculated by applying a B-spline-based deformable image registration, and the results for phase-controlled layered rescanning (PCR{sub L}) and phase-controlled volumetric rescanning (PCR{sub V}) were compared. Results: For the phantom study, simple LR was unable to improve the dose distributions for an increased number of rescannings. The phase-controlled technique without rescanning (1 Multiplication-Sign PCR{sub L} and 1 Multiplication-Sign PCR{sub V}) degraded dose conformity significantly due to a reduced scan velocity. In contrast, 4 Multiplication-Sign PCR{sub L} or more significantly and consistently improved dose distribution. PCR{sub V} showed interference effects, but in general also improved dose homogeneity with higher numbers of rescannings. Dose distributions with single PCR{sub L}/PCR{sub V} with a sweep direction perpendicular to motion direction showed large hot/cold spots; however, this effect vanished with higher numbers of rescannings for both methods. Similar observations were obtained for the other dose metrics, such as target motion (SI/AP), amplitude (6-22 mm peak-to-peak) and respiratory period (3.0-5.0 s). For four or more rescannings, both methods showed significantly better results, albeit that volumetric PCR was more affected by interference effects, which lead to severe degradation of a few dose distributions. The clinical example showed the same tendencies as the phantom study. Dose assessment metrics (D95, Dmax/Dmin, homogeneity index) were improved with an increasing number of PCR{sub L}/PCR{sub V}, but with PCR{sub L} being more robust. Conclusions: PCR{sub L} requires a longer treatment time than PCR{sub V} for high numbers of rescannings in the NIRS scanning system but is more robust. Although four or more rescans provided good dose homogeneity and conformity, the authors prefer to use more rescannings for clinical cases to further minimize dose degradation effects due to organ motion.

Mori, Shinichiro; Furukawa, Takuji; Inaniwa, Taku; Zenklusen, Silvan; Nakao, Minoru; Shirai, Toshiyuki; Noda, Koji [Research Center for Charged Particle Therapy, National Institute of Radiological Sciences, Inage-ku, Chiba 263-8555 (Japan)

2013-03-15T23:59:59.000Z

96

Vehicle Technologies Office: Hybrid and Vehicle Systems  

NLE Websites -- All DOE Office Websites (Extended Search)

Hybrid and Vehicle Hybrid and Vehicle Systems to someone by E-mail Share Vehicle Technologies Office: Hybrid and Vehicle Systems on Facebook Tweet about Vehicle Technologies Office: Hybrid and Vehicle Systems on Twitter Bookmark Vehicle Technologies Office: Hybrid and Vehicle Systems on Google Bookmark Vehicle Technologies Office: Hybrid and Vehicle Systems on Delicious Rank Vehicle Technologies Office: Hybrid and Vehicle Systems on Digg Find More places to share Vehicle Technologies Office: Hybrid and Vehicle Systems on AddThis.com... Just the Basics Hybrid & Vehicle Systems Modeling & Simulation Integration & Validation Benchmarking Parasitic Loss Reduction Propulsion Systems Advanced Vehicle Evaluations Energy Storage Advanced Power Electronics & Electrical Machines

97

Alternative Fuels Data Center: Heavy-Duty Vehicle and Engine...  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Freightliner - M2 106 Hybrid Applications: Tractor, Vocational truck Fuel Type: Hybrid - Diesel Electric...

98

Evaluation of auxinic herbicides for broadleaf weed control, tolerance of forage bermudagrass hybrids [Cynodon dactylon (L.) Pers.], and absorption and translocation in common ragweed (Ambrosia artemisiifolia L.)  

E-Print Network (OSTI)

These studies were conducted on several central Texas agricultural producers?? properties, the Stiles Farm Foundation, the Texas Agricultural Experiment Station, and the Texas A&M University campus. First, an experimental herbicide from Dow AgroSciences, GF-884, was evaluated for effectiveness in controlling three annual and three perennial weed species in production pasture lands and hay meadows. Several rates of GF-884 were examined and evaluated against three registered pasture products and one non-selective herbicide. Next, GF-884 was assessed for tolerance on two common bermudagrass hybrids (Cynodon dactylon (L.) Pers.) at three progressive rates with and without adjuvant. Finally, the herbicides, picloram and fluroxypyr, were applied to common ragweed (Ambrosia artemisiifolia L.) to characterize their individual absorption and translocation and assess any influence one might have on the other. GF-884 applied at rates of 0.91 and 1.14 kg a.e./ha provided >85% and >75% control of the annual and perennial weed species evaluated, respectively. These same rates of GF-884 consistently provided control that was equivalent or better than thatachieved with the registered products. No differences were observed among treatments when shoots from the perennial species were evaluated 12 months following treatment application. The tolerance experiments utilized GF-884 at rates twice that used to evaluate weed control efficacy. These elevated rates did not result in discernable influences on yield or forage quality for either hybrid forage grass when compared to untreated areas. The efficacy and tolerance observations suggest that GF-884 applied at the highest recommended weed control rate can effectively control several annual and perennial weed species without imparting detrimental effects to the hybrid bermudagrass being produced. Finally, in the presence of fluroxypyr, 14C picloram absorption was maintained throughout all sampling intervals. Picloram applied alone, maximized 14C absorption at 6 HAT then declined significantly. At the final sampling, 14C from picloram applied alone was in greater concentration in the treated leaf and the root. Picloram significantly decreased absorption of 14C fluroxypyr. Fluroxypyr alone maintained 14C absorption throughout all samplings, whereas the combination maximized at 12 HAT. Initially, picloram limited 14C translocation, however at 6, 12, and 24 HAT this was not evident.

Moore, Frederick Thomas

2003-05-01T23:59:59.000Z

99

Evaluation of battery/microturbine hybrid energy storage technologies at the University of Maryland :a study for the DOE Energy Storage Systems Program.  

DOE Green Energy (OSTI)

This study describes the technical and economic benefits derived from adding an energy storage component to an existing building cooling, heating, and power system that uses microturbine generation to augment utility-provided power. Three different types of battery energy storage were evaluated: flooded lead-acid, valve-regulated lead-acid, and zinc/bromine. Additionally, the economic advantages of hybrid generation/storage systems were evaluated for a representative range of utility tariffs. The analysis was done using the Distributed Energy Technology Simulator developed for the Energy Storage Systems Program at Sandia National Laboratories by Energetics, Inc. The study was sponsored by the U.S. DOE Energy Storage Systems Program through Sandia National Laboratories and was performed in coordination with the University of Maryland's Center for Environmental Energy Engineering.

De Anda, Mindi Farber (Energetics, Inc., Washington, DC); Fall, Ndeye K. (Energetics, Inc., Washington, DC)

2005-03-01T23:59:59.000Z

100

Hybrid solar-fossil fuel power generation  

E-Print Network (OSTI)

In this thesis, a literature review of hybrid solar-fossil fuel power generation is first given with an emphasis on system integration and evaluation. Hybrid systems are defined as those which use solar energy and fuel ...

Sheu, Elysia J. (Elysia Ja-Zeng)

2012-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "hybrid tractor evaluation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Hybrid Vehicle Links  

NLE Websites -- All DOE Office Websites (Extended Search)

Hybrid Links Hybrid Links Exit Fueleconomy.gov The links below are to pages that are not part of the fueleconomy.gov Web site. We offer these external links for your convenience in accessing additional information that may be useful or interesting to you. Hybrid Vehicles and Manufacturers Acura ILX Hybrid Audi Q5 Hybrid BMW ActiveHybrid 3 ActiveHybrid 5 ActiveHybrid 7 Buick LaCrosse eAssist* Regal eAssist* Chevrolet Malibu Eco* Impala eAssist* Ford Fusion Hybrid Honda Accord Hybrid Civic Hybrid Honda CR-Z Honda Insight Hyundai Sonata Hybrid Infiniti M Hybrid Q50 Hybrid Q50 S Hybrid QX60 Hybrid Kia Optima Hybrid Lexus CT 200h Lexus ES 300h GS 450h LS 600h L RX 450h Lincoln MKZ Hybrid Mercedes-Benz Mercedes E400 Hybrid Nissan Pathfinder Hybrid Porsche Cayenne S Hybrid Subaru XV Crosstrek Hybrid Toyota Avalon Hybrid

102

In-Use and Vehicle Dynamometer Evaluation and Comparison of Class 7 Hybrid Electric and Conventional Diesel Delivery Trucks  

SciTech Connect

This study compared fuel economy and emissions between heavy-duty hybrid electric vehicles (HEVs) and equivalent conventional diesel vehicles. In-use field data were collected from daily fleet operations carried out at a FedEx facility in California on six HEV and six conventional 2010 Freightliner M2-106 straight box trucks. Field data collection primarily focused on route assessment and vehicle fuel consumption over a six-month period. Chassis dynamometer testing was also carried out on one conventional vehicle and one HEV to determine differences in fuel consumption and emissions. Route data from the field study was analyzed to determine the selection of dynamometer test cycles. From this analysis, the New York Composite (NYComp), Hybrid Truck Users Forum Class 6 (HTUF 6), and California Air Resource Board (CARB) Heavy Heavy-Duty Diesel Truck (HHDDT) drive cycles were chosen. The HEV showed 31% better fuel economy on the NYComp cycle, 25% better on the HTUF 6 cycle and 4% worse on the CARB HHDDT cycle when compared to the conventional vehicle. The in-use field data indicates that the HEVs had around 16% better fuel economy than the conventional vehicles. Dynamometer testing also showed that the HEV generally emitted higher levels of nitric oxides than the conventional vehicle over the drive cycles, up to 77% higher on the NYComp cycle (though this may at least in part be attributed to the different engine certification levels in the vehicles tested). The conventional vehicle was found to accelerate up to freeway speeds over ten seconds faster than the HEV.

Burton, J.; Walkowicz, K.; Sindler, P.; Duran, A.

2013-10-01T23:59:59.000Z

103

Low Wind Speed Technology Phase I: Evaluation of Design and Construction Approaches for Economical Hybrid Steel/Concrete Wind Turbine Towers; BERGER/ABAM Engineers Inc.  

DOE Green Energy (OSTI)

This fact sheet describes a subcontract with BERGER/ABAM Engineers Inc. to study the economic feasibility of concrete and hybrid concrete/steel wind turbine towers.

Not Available

2006-03-01T23:59:59.000Z

104

Evaluation of a Current Source Active Power Filter to Reduce the DC Bus Capacitor in a Hybrid Electric Vehicle Traction Drive  

E-Print Network (OSTI)

Science Knoxville, TN, 37996, USA tolbert@utk.edu Abstract ­ In hybrid electric vehicles (HEV), a battery-source inverter, dc bus capacitor, Electric vehicle, Harmonic current, Hybrid electric vehicle. I. INTRODUCTION Electric Vehicle Traction Drive Shengnan Li Student Member, IEEE The University of Tennessee Department

Tolbert, Leon M.

105

Hybrid: Overview  

NLE Websites -- All DOE Office Websites (Extended Search)

button highlighted Starting Button Cruising Button Passing Button Braking Button Stopped Button subbanner graphic: gray bar button highlighted Starting Button Cruising Button Passing Button Braking Button Stopped Button subbanner graphic: gray bar OVERVIEW Hybrid-electric vehicles combine the benefits of gasoline engines and electric motors to provide improved fuel economy. The engine provides most of the vehicle's power, and the electric motor provides additional power when needed, such as for accelerating and passing. This allows a smaller, more-efficient engine to be used. The electric power for the motor is generated from regenerative braking and from the gasoline engine, so hybrids don't have to be "plugged in" to an electrical outlet to recharge. stage graphic: vertical blue rule Main stage: See through car with battery, engine, and electric motor visible. The car is stopped at an intersection.

106

Hybrid: Overview  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

button highlighted Starting Button Cruising Button Passing Button Braking Button Stopped Button subbanner graphic: gray bar button highlighted Starting Button Cruising Button Passing Button Braking Button Stopped Button subbanner graphic: gray bar OVERVIEW Hybrid-electric vehicles combine the benefits of gasoline engines and electric motors to provide improved fuel economy. The engine provides most of the vehicle's power, and the electric motor provides additional power when needed, such as for accelerating and passing. This allows a smaller, more-efficient engine to be used. The electric power for the motor is generated from regenerative braking and from the gasoline engine, so hybrids don't have to be "plugged in" to an electrical outlet to recharge. stage graphic: vertical blue rule Main stage: See through car with battery, engine, and electric motor visible. The car is stopped at an intersection.

107

Plug-In Hybrid Electric Vehicle Value Proposition Study: Phase 1, Task 3: Technical Requirements and Procedure for Evaluation of One Scenario  

DOE Green Energy (OSTI)

In Task 2, the project team designed the Phase 1 case study to represent the 'baseline' plug-in hybrid electric vehicle (PHEV) fleet of 2030 that investigates the effects of seventeen (17) value propositions (see Table 1 for complete list). By creating a 'baseline' scenario, a consistent set of assumptions and model parameters can be established for use in more elaborate Phase 2 case studies. The project team chose southern California as the Phase 1 case study location because the economic, environmental, social, and regulatory conditions are conducive to the advantages of PHEVs. Assuming steady growth of PHEV sales over the next two decades, PHEVs are postulated to comprise approximately 10% of the area's private vehicles (about 1,000,000 vehicles) in 2030. New PHEV models introduced in 2030 are anticipated to contain lithium-ion batteries and be classified by a blended mileage description (e.g., 100 mpg, 150 mpg) that demonstrates a battery size equivalence of a PHEV-30. Task 3 includes the determination of data, models, and analysis procedures required to evaluate the Phase 1 case study scenario. Some existing models have been adapted to accommodate the analysis of the business model and establish relationships between costs and value to the respective consumers. Other data, such as the anticipated California generation mix and southern California drive cycles, have also been gathered for use as inputs. The collection of models that encompasses the technical, economic, and financial aspects of Phase 1 analysis has been chosen and is described in this deliverable. The role of PHEV owners, utilities (distribution systems, generators, independent system operators (ISO), aggregators, or regional transmission operators (RTO)), facility owners, financing institutions, and other third parties are also defined.

Sikes, Karen R [ORNL; Hinds, Shaun [Sentech, Inc.; Hadley, Stanton W [ORNL; McGill, Ralph N [ORNL; Markel, Lawrence C [ORNL; Ziegler, Richard E [ORNL; Smith, David E [ORNL; Smith, Richard L [ORNL; Greene, David L [ORNL; Brooks, Daniel L [ORNL; Wiegman, Herman [GE Global Research; Miller, Nicholas [GE; Marano, Dr. Vincenzo [Ohio State University

2008-07-01T23:59:59.000Z

108

Evaluation of commercial lithium-ion cells based on composite positive electrode for plug-in hybrid electric vehicle applications. Part I: Initial characterizations  

Science Conference Proceedings (OSTI)

Evaluating commercial Li-ion batteries presents some unique benefits. One of them is to use cells made from established fabrication process and form factor, such as those offered by the 18650 cylindrical configuration, to provide a common platform to investigate and understand performance deficiency and aging mechanism of target chemistry. Such an approach shall afford us to derive relevant information without influence from processing or form factor variability that may skew our understanding on cell-level issues. A series of 1.9 Ah 18650 lithium ion cells developed by a commercial source using a composite positive electrode comprising (LiMn1/3Ni1/3Co1/3O2 + LiMn2O4) is being used as a platform for the investigation of certain key issues, particularly path-dependent aging and degradation in future plug-in hybrid electric vehicle (PHEV) applications, under the US Department of Energy's Applied Battery Research (ABR) program. Here we report in Part I the initial characterizations of the cell performance and Part II some aspects of cell degradation in 2C cycle aging. The initial characterizations, including cell-to-cell variability, are essential for life cycle performance characterization in the second part of the report when cell-aging phenomena are discussed. Due to the composite nature of the positive electrode, the features (or signature) derived from the incremental capacity (IC) of the cell appear rather complex. In this work, the method to index the observed IC peaks is discussed. Being able to index the IC signature in details is critical for analyzing and identifying degradation mechanism later in the cycle aging study.

Matthieu Dubarry; Cyril Truchot; Mikael Cugnet; Bor Yann Liaw; Kevin Gering; Sergiy Sazhin; David Jamison; Christopher Michelbacher

2011-12-01T23:59:59.000Z

109

Hybrid automobile  

SciTech Connect

The invention discloses a parallel hybrid drive system for self propelled vehicles including a direct current motor-generator having a drive shaft in common with an internal combustion engine leading to a variable speed transmission and a final drive train. The motor-generator has a no-load speed, established by a separate field exciter, below which it drives the shaft as a motor and above which it is driven by the shaft as a generator. Storage batteries are operatively connected to the motor-generator to supply power to it below the no-load speed. The internal combustion engine operates over a small RPM range around its most efficient speed at a power level established by a fixed throttle setting. The transmission is operatively connected to an accelerator and direction selector switch to vary the speed and direction of the vehicle.

Lynch, T.E.; Eastman, D.P.; Price, R.P.

1979-08-28T23:59:59.000Z

110

Evaluation of performance and magnetic characteristics of a radial-radial flux compound-structure permanent-magnet synchronous machine used for hybrid electric vehicle  

Science Conference Proceedings (OSTI)

A breed of compound-structure permanent-magnet synchronous machine (CS-PMSM) is used for power-split hybrid electric vehicles(HEVs). It can help to fulfill both the speed and torque control of the internal combustion engine and

Ping Zheng; Ranran Liu; Lin Shen; Lina Li; Weiguang Fan; Qian Wu; Jing Zhao

2008-01-01T23:59:59.000Z

111

Evaluation of various dietary supplements and strategies to enhance growth and disease management of hybrid striped bass Morone chrysops x M. saxatilis  

E-Print Network (OSTI)

The US hybrid striped bass (Morone chrysops x M. saxatilis) industry has been negatively impacted by infectious diseases because there are very few approved drugs and vaccines. Therefore, a series of experiments was conducted to explore the potential use of various dietary supplements including autolyzed brewers yeast, the commercial prebiotic GroBiotic®, oligonucleotides and levamisole for improvement of hybrid striped bass growth, immunity and resistance to disease caused by various pathogenic bacteria. In two trials with brewers yeast, fish fed diets supplemented with yeast at 2% generally showed enhanced weight gain and feed efficiency compared with those fed a basal diet. Brewers yeast also positively influenced resistance to S. iniae infection. In addition, results of immune response assays demonstrated that brewers yeast can be administered for relatively long periods without causing immunosuppression. GroBiotic® (Grobiotic) also resulted in significantly enhanced weight gain, innate immune responses and resistance of juvenile hybrid striped bass to S. iniae infection. An additional experiment with sub-adult fish showed significantly reduced mortality of fish fed a diet supplemented with GroBiotic® at 2% when subjected to an in-situ Mycobacterium marinum challenge. This is the first report of positive effects from dietary prebiotics for fish health management, although many fundamental questions should be pursued further. Dietary supplementation of a commercial oligonucleotide product (Ascogen P®) at 0.5% of the diet was shown to enhance resistance of hybrid striped bass against S. iniae infection and increased their neutrophil oxidative radical production. However, the effect on growth was marginal. Dietary levamisole supplementation at a low level (100 mg/kg) enhanced the growth and feed efficiency of juvenile hybrid striped bass. However, an elevated dosage (1000 mg/kg diet) strongly suppressed growth, feed intake and feed efficiency. Hypothesized beneficial influences, including antibody production and resistance to S. iniae and A. hydrophila were not substantiated. Although dietary levamisole increased fish macrophage respiratory burst, an in vitro study failed to show a direct effect on cultured macrophages. This suite of studies demonstrated the potential use of some dietary supplements to enhance hybrid striped bass production. Thus, immunonutrition represents a valuable strategy to apply in aquaculture.

Li, Peng

2005-12-01T23:59:59.000Z

112

Formula Hybrid International Competition  

E-Print Network (OSTI)

challenge. We are delighted that they are directing their ingenuity and creativity to advancing hybrid with a traditional combustion engine into a hybrid vehicle, overcoming numerous technical challenges along the way of the hybrid gasoline engine, there are more components to a hybrid drivetrain, including the electric motor

Carver, Jeffrey C.

113

Knoxville Area Transit: Propane Hybrid Electric Trolleys  

DOE Green Energy (OSTI)

A 2-page fact sheet summarizing the evaluation done by the U.S. Department of Energy's Advanced Vehicle Testing Activity on the Knoxville Area Transit's use of propane hybrid electric trolleys.

Not Available

2005-04-01T23:59:59.000Z

114

Case Study: Ebus Hybrid Electric Buses and Trolleys  

DOE Green Energy (OSTI)

Evaluation focuses on the demonstration of hybrid electric buses and trolleys produced by Ebus Inc. at the Indianapolis Transportation Corporation and the Knoxville Area Transit.

Barnitt, R.

2006-07-01T23:59:59.000Z

115

Hybrid Molten Bed Gasifier for High Hydrogen Syngas Production  

NLE Websites -- All DOE Office Websites (Extended Search)

Hybrid Molten Bed Gasifier for High Hydrogen (H2) Syngas Production Gas Technology Institute (GTI) Project Number: FE0012122 Project Description The research team will evaluate and...

116

Design, simulation, and construction of a series hybrid electric vehicle.  

E-Print Network (OSTI)

??This thesis evaluates a series hybrid electric drivetrain design for use in parking patrol vehicles. Due to the particular attributes of this application, it is… (more)

Northcott, Daniel Ross

2007-01-01T23:59:59.000Z

117

Mesoscale hybrid calibration artifact  

DOE Patents (OSTI)

A mesoscale calibration artifact, also called a hybrid artifact, suitable for hybrid dimensional measurement and the method for make the artifact. The hybrid artifact has structural characteristics that make it suitable for dimensional measurement in both vision-based systems and touch-probe-based systems. The hybrid artifact employs the intersection of bulk-micromachined planes to fabricate edges that are sharp to the nanometer level and intersecting planes with crystal-lattice-defined angles.

Tran, Hy D. (Albuquerque, NM); Claudet, Andre A. (Albuquerque, NM); Oliver, Andrew D. (Waltham, MA)

2010-09-07T23:59:59.000Z

118

Hybrid armature projectile  

SciTech Connect

A projectile for a railgun that uses a hybrid armature and provides a seed block around part of the outer surface of the projectile to seed the hybrid plasma brush. In addition, the hybrid armature is continuously vaporized to replenish plasma in a plasma armature to provide a tandem armature and provides a unique ridge and groove to reduce plasama blowby.

Hawke, Ronald S. (Livermore, CA); Asay, James R. (Los Lunas, NM); Hall, Clint A. (Albuquerque, NM); Konrad, Carl H. (Albuquerque, NM); Sauve, Gerald L. (Berthoud, CO); Shahinpoor, Mohsen (Albuquerque, NM); Susoeff, Allan R. (Pleasanton, CA)

1993-01-01T23:59:59.000Z

119

The hydrogen hybrid option  

SciTech Connect

The energy efficiency of various piston engine options for series hybrid automobiles are compared with conventional, battery powered electric, and proton exchange membrane (PEM) fuel cell hybrid automobiles. Gasoline, compressed natural gas (CNG), and hydrogen are considered for these hybrids. The engine and fuel comparisons are done on a basis of equal vehicle weight, drag, and rolling resistance. The relative emissions of these various fueled vehicle options are also presented. It is concluded that a highly optimized, hydrogen fueled, piston engine, series electric hybrid automobile will have efficiency comparable to a similar fuel cell hybrid automobile and will have fewer total emissions than the battery powered vehicle, even without a catalyst.

Smith, J.R.

1993-10-15T23:59:59.000Z

120

How Hybrids Work  

NLE Websites -- All DOE Office Websites (Extended Search)

How Hybrids Work How Hybrids Work Diagram of full hybrid vehicle components, including (1) an internal combustion engine, (2) an electric motor, (3) a generator, (4) a power split device, and (5) a high-capacity battery. Flash Animation: How Hybrids Work (Requires Flash 6.0 or higher) HTML Version: How Hybrids Work Hybrid-electric vehicles (HEVs) combine the benefits of gasoline engines and electric motors and can be configured to obtain different objectives, such as improved fuel economy, increased power, or additional auxiliary power for electronic devices and power tools. Some of the advanced technologies typically used by hybrids include Regenerative Braking. The electric motor applies resistance to the drivetrain causing the wheels to slow down. In return, the energy from the

Note: This page contains sample records for the topic "hybrid tractor evaluation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Hybrid Cooling Systems  

Science Conference Proceedings (OSTI)

Water consumption by power plants has become an increasingly contentious siting issue. In nearly all fossil-fired and nuclear plants, water for plant cooling is by far the greatest water requirement. Therefore, the use of water-conserving cooling systems such as dry or hybrid cooling is receiving increasing attention. This technology overview from the Electric Power Research Institute (EPRI) provides a brief introduction to hybrid cooling systems. As defined in the report, the term "hybrid cooling" refer...

2011-11-23T23:59:59.000Z

122

2011 Hyundai Sonata Hybrid  

NLE Websites -- All DOE Office Websites (Extended Search)

Sonata Hybrid Test cell location 2WD Vehicle Setup Information Downloadable Dynamometer Database (D 3 )- Test Summary Sheet Vehicle architecture P2 HEV Vehicle Dynamometer Input...

123

Test des Systèmes hybrides.  

E-Print Network (OSTI)

??Les systèmes hybrides, systèmes combinant à la fois une dynamique continue et discrète, s'avèrent être un modèle mathématique utile pour différents phénomènes physiques, technologiques, biologiques… (more)

Nahhal, Tarik

124

Alternative Fuels Data Center: Heavy-Duty Vehicle and Engine...  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Kenworth - T370 diesel electric tractor Application: Tractor Fuel Type: Hybrid - Diesel Electric Maximum Seating: 3 Power Source(s): Paccar - PX-6 6.7L Hybrid System(s): Eaton -...

125

New & Upcoming Hybrid Vehicles  

NLE Websites -- All DOE Office Websites (Extended Search)

New & Upcoming Hybrids New & Upcoming Hybrids 2014 Model Year Vehicle EPA MPG Estimates Price (MSRP) Chevrolet Impala eAssist Large Car Chevrolet Impala eAssist Chart: City, 25; Highway, 35; Combined, 29 NA Infiniti Q50 Hybrid Compact Car Infiniti Q50 Hybrid Chart: City, 29; Highway, 36; Combined, 31 $43,950 Infiniti Q50 Hybrid AWD Compact Car Infiniti Q50 Hybrid AWD Chart: City, 28; Highway, 35; Combined, 30 $45,750 Infiniti Q50S Hybrid Compact Car Infiniti Q50S Hybrid Chart: City, 28; Highway, 34; Combined, 30 $46,350 Infiniti Q50S Hybrid AWD Compact Car Infiniti Q50S Hybrid AWD Chart: City, 27; Highway, 31; Combined, 28 $48,150 Infiniti QX60 Hybrid AWD Standard SUV Infiniti QX60 Hybrid AWD Chart: City, 25; Highway, 28; Combined, 26 NA Infiniti QX60 Hybrid FWD

126

Fuel-Cycle energy and emission impacts of ethanol-diesel blends in urban buses and farming tractors.  

DOE Green Energy (OSTI)

About 2.1 billion gallons of fuel ethanol was used in the United States in 2002, mainly in the form of gasoline blends containing up to 10% ethanol (E10). Ethanol use has the potential to increase in the U.S. blended gasoline market because methyl tertiary butyl ether (MTBE), formerly the most popular oxygenate blendstock, may be phased out owing to concerns about MTBE contamination of the water supply. Ethanol would remain the only viable near-term option as an oxygenate in reformulated gasoline production and to meet a potential federal renewable fuels standard (RFS) for transportation fuels. Ethanol may also be blended with additives (co-solvents) into diesel fuels for applications in which oxygenation may improve diesel engine emission performance. Numerous studies have been conducted to evaluate the fuel-cycle energy and greenhouse gas (GHG) emission effects of ethanol-gasoline blends relative to those of gasoline for applications in spark-ignition engine vehicles (see Wang et al. 1997; Wang et al. 1999; Levelton Engineering et al. 1999; Shapouri et al. 2002; Graboski 2002). Those studies did not address the energy and emission effects of ethanol-diesel (E-diesel or ED) blends relative to those of petroleum diesel fuel in diesel engine vehicles. The energy and emission effects of E-diesel could be very different from those of ethanol-gasoline blends because (1) the energy use and emissions generated during diesel production (so-called ''upstream'' effects) are different from those generated during gasoline production; and (2) the energy and emission performance of E-diesel and petroleum diesel fuel in diesel compression-ignition engines differs from that of ethanol-gasoline blends in spark-ignition (Otto-cycle-type) engine vehicles. The Illinois Department of Commerce and Community Affairs (DCCA) commissioned Argonne National Laboratory to conduct a full fuel-cycle analysis of the energy and emission effects of E-diesel blends relative to those of petroleum diesel when used in the types of diesel engines that will likely be targeted first in the marketplace. This report documents the results of our study. The draft report was delivered to DCCA in January 2003. This final report incorporates revisions by the sponsor and by Argonne.

Wang, M.; Saricks, C.; Lee, H.

2003-09-11T23:59:59.000Z

127

Plug-In Hybrid Electric Vehicle  

NLE Websites -- All DOE Office Websites (Extended Search)

* Batteries * Batteries * Downloadable Dynanometer Database (D3) * Modeling * Prototypes * Testing * Assessment PSAT Smart Grid Student Competitions Technology Analysis Transportation Research and Analysis Computing Center Working With Argonne Contact TTRDC Argonne Leads DOE's Effort to Evaluate Plug-in Hybrid Technology aprf testing Argonne's Advanced Powertrain Research Facility (APRF) enables researchers to conduct vehicle benchmarking and testing activities that provide data critical to the development and commercialization of next-generation vehicles such as PHEVs. Argonne's Research Argonne National Laboratory is the U.S. Department of Energy's lead national laboratory for the simulation, validation and laboratory evaluation of plug-in hybrid electric vehicles and the advanced

128

Hybrid options for light-duty vehicles.  

DOE Green Energy (OSTI)

Hybrid electric vehicles (HEVs) offer great promise in improving fuel economy. In this paper, we analyze why, how, and by how much vehicle hybridization can reduce energy consumption and improve fuel economy. Our analysis focuses on efficiency gains associated solely with vehicle hybridization. We do not consider such other measures as vehicle weight reduction or air- and tire-resistance reduction, because such measures would also benefit conventional technology vehicles. The analysis starts with understanding the energy inefficiencies of light-duty vehicles associated with different operation modes in US and Japanese urban and highway driving cycles, with the corresponding energy-saving potentials. The potential for fuel economy gains due to vehicle hybridization can be estimated almost exclusively on the basis of three elements: the reducibility of engine idling operation, the recoverability of braking energy losses, and the capability of improving engine load profiles to gain efficiency associated with specific HEV configurations and control strategies. Specifically, we evaluate the energy efficiencies and fuel economies of a baseline MY97 Corolla-like conventional vehicle (CV), a hypothetical Corolla-based minimal hybrid vehicle (MHV), and a MY98 Prius-like full hybrid vehicle (FHV). We then estimate energy benefits of both MHVs and FHVs over CVs on a performance-equivalent basis. We conclude that the energy benefits of hybridization vary not only with test cycles, but also with performance requirements. The hybrid benefits are greater for ''Corolla (high) performance-equivalent'' vehicles than for ''Prius (low) performance-equivalent'' vehicles. An increasing acceleration requirement would result in larger fuel economy benefits from vehicle hybridization.

An, F., Stodolsky, F.; Santini, D.

1999-07-19T23:59:59.000Z

129

Analysis of a diesel-electric hybrid urban bus system  

DOE Green Energy (OSTI)

A hybrid bus powered by a diesel engine and a battery pack has been analyzed over an idealized bus-driving cycle in Chicago. Three hybrid configurations, two parallel and one series, have been evaluated. The results indicate that the fuel economy of a hybrid bus, taking into account the regenerative braking, is comparable with that of a conventional diesel bus. Life-cycle costs are slightly higher because of the added weight and cost of the battery.

Marr, W.W.; Sekar, R.R. [Argonne National Lab., IL (United States); Ahlheim, M.C. [Regional Transportation Authority, Chicago, IL (United States)

1993-08-01T23:59:59.000Z

130

Alternative Fuels Data Center: Heavy-Duty Vehicle and Engine...  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

86HE Application: Tractor Fuel Type: Hybrid - Diesel Electric Power Source(s): Paccar - MX-13 Hybrid System(s): Eaton - Diesel Electric Hybrid...

131

Hybrid Electric Vehicles  

Energy.gov (U.S. Department of Energy (DOE))

Hybrid electric vehicles (HEVs) combine the benefits of high fuel economy and low emissions with the power, range, and convenience of conventional diesel and gasoline fueling. HEV technologies also have potential to be combined with alternative fuels and fuel cells to provide additional benefits. Future offerings might also include plug-in hybrid electric vehicles.

132

Energy Basics: Hybrid Electric Vehicles  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

a hybrid electric vehicle. Hybrid electric vehicles (HEVs) combine the benefits of high fuel economy and low emissions with the power, range, and convenience of conventional diesel...

133

Hybrid or electric vehicles? A real options perspective  

Science Conference Proceedings (OSTI)

This paper investigates the decision of an automaker concerning the alternative promotion of a hybrid vehicle (HV) and a full electric vehicle (EV). We evaluate the HV project by considering the option to change promotion from the HV to the EV in the ... Keywords: Alternative projects, American options on multiple assets, Exercise region, Hybrid and electric vehicles, Real options

Michi Nishihara

2010-03-01T23:59:59.000Z

134

Analysis of the fuel economy benefit of drivetrain hybridization  

DOE Green Energy (OSTI)

Parallel- and series-configured hybrid vehicles likely feasible in next decade arc defined and evaluated using NREL's flexible ADvanced VehIcle SimulatOR ADVISOR. Fuel economics of these two diesel-powered hybrid vehicles are compared to a comparable-technology diesel- powered internal-combustion-engine vehicle. Sensitivities of these fuel economies to various vehicle and component parameters are determined and differences among them are explained. The fuel economy of the parallel hybrid defined here is 24% better than the internal- combustion-engine vehicle and 4% better than the series hybrid.

Cuddy, M.R.; Wipke, K.B.

1997-01-01T23:59:59.000Z

135

Hybrid Vehicle Technology - Home  

NLE Websites -- All DOE Office Websites (Extended Search)

* Batteries * Batteries * Modeling * Testing Hydrogen & Fuel Cells Materials Modeling, Simulation & Software Plug-In Hybrid Electric Vehicles PSAT Smart Grid Student Competitions Technology Analysis Transportation Research and Analysis Computing Center Working With Argonne Contact TTRDC Hybrid Vehicle Technology revolutionize transportation Argonne's Research Argonne researchers are developing and testing various hybrid electric vehicles (HEVs) and their components to identify the technologies, configurations, and engine control strategies that provide the best combination of high fuel economy and low emissions. Vehicle Validation Argonne also serves as the lead laboratory for hardware-in-the-loop (HIL) and technology validation for the U.S. Department of Energy (DOE). HIL is a

136

Hybrid electric vehicles TOPTEC  

SciTech Connect

This one-day TOPTEC session began with an overview of hybrid electric vehicle technology. Updates were given on alternative types of energy storage, APU control for low emissions, simulation programs, and industry and government activities. The keynote speech was about battery technology, a key element to the success of hybrids. The TOPEC concluded with a panel discussion on the mission of hybrid electric vehicles, with a perspective from industry and government experts from United States and Canada on their view of the role of this technology.

1994-06-21T23:59:59.000Z

137

Artificial mismatch hybridization  

DOE Patents (OSTI)

An improved nucleic acid hybridization process is provided which employs a modified oligonucleotide and improves the ability to discriminate a control nucleic acid target from a variant nucleic acid target containing a sequence variation. The modified probe contains at least one artificial mismatch relative to the control nucleic acid target in addition to any mismatch(es) arising from the sequence variation. The invention has direct and advantageous application to numerous existing hybridization methods, including, applications that employ, for example, the Polymerase Chain Reaction, allele-specific nucleic acid sequencing methods, and diagnostic hybridization methods.

Guo, Zhen (Madison, WI); Smith, Lloyd M. (Madison, WI)

1998-01-01T23:59:59.000Z

138

Dual-Mode Hybrid/Two-Mode Hybrid Accomplishment  

NLE Websites -- All DOE Office Websites (Extended Search)

Dual-Mode Hybrid/Two-Mode Hybrid Accomplishment Dual-Mode Hybrid/Two-Mode Hybrid Accomplishment DOE-funded research, in collaboration with Allison Buses and General Motors Corporation has led to the commercialization of a dramatically different hybrid transmission system for heavy-duty and light-duty applications. The Dual-Mode or Two-Mode hybrid system is an infinitely variable speed hybrid transmission that works with the engine and battery system and automatically chooses to operate in a parallel or series hybrid path to maximize efficiency and minimize emissions, fuel consumption and noise. Parallel and Series hybrid configurations are found on most hybrid vehicles today, both with their own pluses and minuses. The Dual- Mode/Two-Mode systems uses the positive characteristics from both systems to maximize fuel

139

Hybrid matrix geometric algebra  

Science Conference Proceedings (OSTI)

The structures of matrix algebra and geometric algebra are completely compatible and in many ways complimentary, each having their own advantages and disadvantages. We present a detailed study of the hybrid 2 × 2 matrix geometric algebra M(2,IG) ...

Garret Sobczyk; Gordon Erlebacher

2004-05-01T23:59:59.000Z

140

Hybrid Systems Diagnosis  

Science Conference Proceedings (OSTI)

This paper reports on an on-going project to investigate techniques to diagnose complex dynamical systems that are modeled as hybrid systems. In particular, we examine continuous systems with embedded supervisory controllers that experience abrupt, partial ...

Sheila A. McIlraith; Gautam Biswas; Dan Clancy; Vineet Gupta

2000-03-01T23:59:59.000Z

Note: This page contains sample records for the topic "hybrid tractor evaluation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Diesel hybridization and emissions.  

DOE Green Energy (OSTI)

The CTR Vehicle Systems and Fuels team a diesel hybrid powertrain. The goal of this experiment was to investigate and demonstrate the potential of diesel engines for hybrid electric vehicles (HEVs) in a fuel economy and emissions. The test set-up consisted of a diesel engine coupled to an electric motor driving a Continuously Variable Transmission (CVT). This hybrid drive is connected to a dynamometer and a DC electrical power source creating a vehicle context by combining advanced computer models and emulation techniques. The experiment focuses on the impact of the hybrid control strategy on fuel economy and emissions-in particular, nitrogen oxides (NO{sub x}) and particulate matter (PM). The same hardware and test procedure were used throughout the entire experiment to assess the impact of different control approaches.

Pasquier, M.; Monnet, G.

2004-04-21T23:59:59.000Z

142

Assimilating hybridized architecture  

E-Print Network (OSTI)

The thesis searches for means of operation to deal with hybridized architecture. As a conceptual framework, sociology theory appears to be an insightful precedent, for it analyzes and classifies how multiple constituents ...

Wu, Jane C., 1977-

2005-01-01T23:59:59.000Z

143

Evaluation of Whole and Lipid-Extracted Algae Meals (LEA) in the Diet of Juvenile Red Drum (Sciaenops ocellatus) and Digestibility of LEA by Red Drum and Hybrid Striped Bass (Morone chrysops x Morone saxatilis)  

E-Print Network (OSTI)

As aquaculture continues to expand, protein sources have become more costly and less available. Simultaneously, lipid-extracted algal meals (LEA) (co-products of bio-diesel production) are becoming increasingly available as alternative sources of energy are investigated. By integrating LEA into aquaculture diets, feed prices could be lowered and bio-diesel production would have an additional revenue stream. Three feeding trials each of 7 weeks duration were conducted to evaluate five different algal meals as partial replacements for fishmeal and soy protein concentrate in diets for juvenile red drum (Sciaenops ocellatus). Apparent digestibility coefficients (ADCs) for CP and energy in various LEAs also were determined with red drum and hybrid striped bass (HSB). In the first trial, whole algae meal and LEA derived from Navicula sp. replaced 5 or 10% of the crude protein (CP) in the reference diet. Weight gain, feed efficiency (FE), hepatosomatic index (HSI), as well as protein and energy retention were not significantly (P>0.05) affected by the dietary treatments. Algal inclusion significantly affected the ADCs of the various dietary treatments for dry matter, CP, and energy. The inclusion of ash in the form of diatomaceous earth improved digestibility of protein as well as weight gain, survival and FE. A second feeding trial evaluated LEA derived from Chlorella sp. processed at high temperatures, replacing 5, 10, 20, and 25% of the CP in the reference diet. Weight gain, FE, survival, and protein efficiency ratio (PER) were significantly reduced at substitution levels of 20 and 25%. The third feeding trial evaluated LEA derived from Nanochloropsis salina, replacing 5, 7.5, 10, and 15% of the CP in the reference diet. Weight gain, FE, survival, and PER were significantly affected by some dietary treatments, with the 15% substitution levels causing significant reductions in performance. Intraperitoneal fat ratio and whole-body lipids were significantly lower in the fish fed the 15% substitution diet. Based on the results of these experiments, replacement of up to 10% of CP from fishmeal and soy protein concentrate with LEA was possible without causing substantial reductions in fish performance, and the whole algae product provided a more nutritious product. Red drum and HSB showed similar responses in their ability to digest CP and energy from the various algal products, although ADCs varied greatly among the different products and processing methods.

Patterson, Donovan Aaron

2013-05-01T23:59:59.000Z

144

New York City Transit Diesel Hybrid-Electric Buses Final Results...  

Open Energy Info (EERE)

of facilities, a description of the project start-up process, evaluation results of hybrid buses studied, lessons learned, and recommendations for future alternative fuel...

145

Plug-in Hybrid Links  

NLE Websites -- All DOE Office Websites (Extended Search)

Plug-in Hybrid Links Plug-in Hybrid Links Exit Fueleconomy.gov The links below are to pages that are not part of the fueleconomy.gov Web site. We offer these external links for your convenience in accessing additional information that may be useful or interesting to you. Plug-in Hybrid Vehicles and Manufacturers Chevrolet Volt Official site for the Chevrolet Volt Cadillac ELR Official site for the Cadillac ELR (arriving early 2014) Ford C-MAX Energi Plug-in Hybrid Official site for the C-MAX Energi Plug-in Hybrid Ford Fusion Energi Plug-in Hybrid Official site for the Fusion Energi Plug-in Hybrid Honda Accord Plug-in Official site for the Honda Accord Plug-in Hybrid Toyota Prius Plug-in Official site for the Toyota Prius Plug-in Hybrid Plug-in-Related Information and Tools

146

Hybrid Systems Architectures  

E-Print Network (OSTI)

ion suppression of lower-level information not relevant for the current task Encapsulation (information hiding) implementation details are hidden, only interface information is visible F. Kurfeß Hybrid System Architectures ASHS '96 37 Inheritance common characteristics are derived from ancestors Polymorphism appropriate instances of classes and operators can be selected at runtime Advantages ffl very flexible ffl suitable for large systems ffl support reuse Problems ffl handling of new and atypical situations ffl quite complex ffl formal verification F. Kurfeß Hybrid System Architectures ASHS '96 38 Expert System What is an Expert System? Basic concepts ffl designer / user supplies facts and information ffl user asks queries and receives expert advice ffl limited to a problem domain (knowledge domain) Components ffl user interface ffl knowledge base ffl inference mechanism Synonyms: knowledge-based system, knowledge-based expert system F. Kurfeß Hybrid System Archi...

Franz J. Kurfeß

1996-01-01T23:59:59.000Z

147

Hybrid Electric Vehicle Testing  

NLE Websites -- All DOE Office Websites (Extended Search)

Transportation Association Conference Transportation Association Conference Vancouver, Canada December 2005 Hybrid Electric Vehicle Testing Jim Francfort U.S. Department of Energy - FreedomCAR & Vehicle Technologies Program, Advanced Vehicle Testing Activity INL/CON-05-00964 Presentation Outline * Background & goals * Testing partners * Hybrid electric vehicle testing - Baseline performance testing (new HEV models) - 1.5 million miles of HEV fleet testing (160k miles per vehicle in 36 months) - End-of-life HEV testing (rerun fuel economy & conduct battery testing @ 160k miles per vehicle) - Benchmark data: vehicle & battery performance, fuel economy, maintenance & repairs, & life-cycle costs * WWW information location Background * Advanced Vehicle Testing Activity (AVTA) - part of the

148

Diagnostics for hybrid reactors  

SciTech Connect

The Hybrid Reactor(HR) can be considered an attractive actinide-burner or a fusion assisted transmutation for destruction of transuranic(TRU) nuclear waste. The hybrid reactor has two important subsystems: the tokamak neutron source and the blanket which includes a fuel zone where the TRU are placed and a tritium breeding zone. The diagnostic system for a HR must be as simple and robust as possible to monitor and control the plasma scenario, guarantee the protection of the machine and monitor the transmutation.

Orsitto, Francesco Paolo [ENEA Unita' Tecnica Fusione , Associazione ENEA-EURATOM sulla Fusione C R Frascati v E Fermi 45 00044 Frascati (Italy)

2012-06-19T23:59:59.000Z

149

Advanced Vehicle Testing Activity: Hybrid Electric Vehicles  

NLE Websites -- All DOE Office Websites (Extended Search)

Hybrid Electric Vehicles to someone by E-mail Share Advanced Vehicle Testing Activity: Hybrid Electric Vehicles on Facebook Tweet about Advanced Vehicle Testing Activity: Hybrid...

150

Issue 5: High Interest in Hybrid Cars  

E-Print Network (OSTI)

and Associates. (2002). Hybrid Vehicle Consumer Acceptancedefinitely” consider a hybrid vehicle, and any of these werepercent or more for a hybrid vehicle. O THER V ARIATIONS IN

Ong, Paul M.; Haselhoff, Kim

2005-01-01T23:59:59.000Z

151

Quantifying the benefits of hybrid vehicles  

E-Print Network (OSTI)

in the last century. Hybrid electric vehicles (HEVs) reduceon their design, hybrid electric vehicles employ electricof this paper, hybrid electric vehicles are a broad set of

Turrentine, Tom; Delucchi, Mark; Heffner, Reid R.; Kurani, Kenneth S; Sun, Yongling

2006-01-01T23:59:59.000Z

152

Efficient simulation of hybrid systems: A hybrid bond graph approach  

Science Conference Proceedings (OSTI)

Accurate and efficient simulations facilitate cost-effective design and analysis of large, complex, embedded systems, whose behaviors are typically hybrid, i.e. continuous behaviors interspersed with discrete mode changes. In this paper we present an ... Keywords: component-oriented modeling, dynamic causal assignment, hybrid bond graphs, modeling and simulation environments, simulation of hybrid systems

Indranil Roychoudhury; Matthew J Daigle; Gautam Biswas; Xenofon Koutsoukos

2011-06-01T23:59:59.000Z

153

Standards Development as Hybridization  

Science Conference Proceedings (OSTI)

While users in the rest of the World have been offered 3G mobile phones based on either the CDMA2000 or W-CDMA standards, users in China have the additional option of using phones based on the TD-SCDMA standard. As a technology largely developed by Chinese ... Keywords: Global, Hybridization, Indigenous, Innovation, Mobile Phones, National, Technology

Xiaobai Shen, Ian Graham, James Stewart, Robin Williams

2013-07-01T23:59:59.000Z

154

Federal Tax Credits for Hybrids  

NLE Websites -- All DOE Office Websites (Extended Search)

Hybrids Hybrids Hybrid Vehicle Photo Federal tax credit up to $3,400! Hybrids purchased or placed into service after December 31, 2005 may be eligible for a federal income tax credit of up to $3,400. Credit amounts begin to phase out for a given manufacturer once it has sold over 60,000 eligible vehicles. Vehicles purchased after December 31, 2010 are not eligible for this credit. The information below is provided for those filing amended tax returns for previous years. BMW Chrysler/Dodge Ford Brands GM Brands Honda Mazda Mercedes Nissan Porsche Toyota/Lexus 2011 Vehicle Make & Model Full Credit Phase Out No Credit 50% 25% BMW Jan. 1, 2006 TBD TBD Jan. 1, 2011 BMW ActiveHybrid 750i 2011 BMW ActiveHybrid 750i $900 -- -- $0 BMW ActiveHybrid 750Li 2011 BMW ActiveHybrid 750Li $900 -- -- $0

155

New Plug-in Hybrids  

NLE Websites -- All DOE Office Websites (Extended Search)

Cars 2014 Midsize Cars Fuel Economy Specs 2013 Chevrolet Volt 2012 Fisker Karma Plug-in Hybrid Vehicle 2012 Chevy Volt Plug-in Hybrid Vehicle 2012 Karma Fisker Configuration...

156

Mirror fusion--fission hybrids  

SciTech Connect

The fusion-fission concept and the mirror fusion-fission hybrid program are outlined. Magnetic mirror fusion drivers and blankets for hybrid reactors are discussed. Results of system analyses are presented and a reference design is described.

Lee, J.D.

1978-05-01T23:59:59.000Z

157

Hybrid and Hierarchical Composite Materials  

Science Conference Proceedings (OSTI)

Chang Soo Kim, University of Wisconsin -Milwaukee. Scope, Hybrid and hierarchical composite materials have several advantageous characteristics that  ...

158

SolarHybrid AG | Open Energy Information  

Open Energy Info (EERE)

SolarHybrid AG Jump to: navigation, search Name SolarHybrid AG Place Germany Sector Solar Product Germany-based solar thermal hybrid product manufacturer References SolarHybrid...

159

Alternative Fuels Data Center: Hybrid Electric Vehicles  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Hybrid Electric Hybrid Electric Vehicles to someone by E-mail Share Alternative Fuels Data Center: Hybrid Electric Vehicles on Facebook Tweet about Alternative Fuels Data Center: Hybrid Electric Vehicles on Twitter Bookmark Alternative Fuels Data Center: Hybrid Electric Vehicles on Google Bookmark Alternative Fuels Data Center: Hybrid Electric Vehicles on Delicious Rank Alternative Fuels Data Center: Hybrid Electric Vehicles on Digg Find More places to share Alternative Fuels Data Center: Hybrid Electric Vehicles on AddThis.com... More in this section... Electricity Basics Benefits & Considerations Stations Vehicles Availability Conversions Emissions Batteries Deployment Maintenance & Safety Laws & Incentives Hybrids Plug-In Hybrids All-Electric Vehicles Hybrid Electric Vehicles

160

Hybrids for Photovoltaics - Programmaster.org  

Science Conference Proceedings (OSTI)

Hybrid Organic: Inorganic Materials for Alternative Energy: Hybrids for Photovoltaics Program Organizers: Andrei Jitianu, Lehman College, City University of ...

Note: This page contains sample records for the topic "hybrid tractor evaluation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Hybrids for Batteries and Fuel Cells  

Science Conference Proceedings (OSTI)

Hybrid Organic: Inorganic Materials for Alternative Energy: Hybrids for Batteries and Fuel Cells Program Organizers: Andrei Jitianu, Lehman College, City ...

162

Conceptual design study for a laser fusion hybrid  

SciTech Connect

Lawrence Livermore Laboratory and Bechtel Corporation have been involved in a joint effort to conceptually design a laser fusion hybrid reactor. The design which has evolved is a depleted-uranium fueled fast-fission blanket which produces fissile plutonium and electricity. A major objective of the design study was to evaluate the feasibility of producing fissile fuel with laser fusion. This feasibility evaluation was carried out by analyzing the integrated engineering performance of the complete conceptual design and by identifying the required laser/pellet performance. The performance of the laser fusion hybrid has also been compared to a typical fast breeder reactor. The results show that the laser fusion hybrid produces enough fissile material to fuel more than six light water reactors (LWR's) of equivalent thermal power while operating in a regime which requires an order of magnitude less laser and pellet performance than pure laser fusion. In comparison to a fast breeder reactor the hybrid produces 10 times more fissile fuel. An economic analysis of the design shows that the cost of electricity in a combined hybrid-LWR scenario is insensitive to the capital cost of the hybrid, increasing by only 20 to 40 percent when the capital cost of the hybrid ranges from 2 to 3 times more than an LWR.

Maniscalco, J.A.

1976-09-01T23:59:59.000Z

163

Can a Hybrid Save Me Money?  

NLE Websites -- All DOE Office Websites (Extended Search)

Can a Hybrid Save Me Money? Can a Hybrid Save Me Money? Step 1: Show me a hybrid. I want to compare... 2013 Acura ILX Hybrid 2013 Acura ILX Hybrid Tech Pkg 2014 Buick LaCrosse eAssist 2013 Cadillac Escalade Hybrid 2WD 2013 Cadillac Escalade Hybrid 4WD 2013 Chevrolet Malibu Eco 2SA 2013 Ford Fusion Hybrid 2013 Ford Fusion Hybrid Titanium 2013 GMC Yukon Denali Hybrid 2WD 2013 GMC Yukon Denali Hybrid 4WD 2013 Honda Insight 2013 Honda Civic Hybrid 2013 Honda Civic Hybrid w/ Nav 2013 Hyundai Sonata Hybrid 2013 Hyundai Sonata Hybrid Limited 2013 Infiniti M35h 2014 Infiniti Q50 Hybrid Premium 2014 Infiniti Q50 Hybrid Premium AWD 2013 Kia Optima Hybrid 2013 Lexus ES 300h 2013 Lexus GS 450h 2013 Lincoln MKZ Hybrid 2013 Toyota Avalon Hybrid XLE Touring 2013 Toyota Avalon Hybrid Limited 2014 Toyota Camry Hybrid LE 2014 Toyota Camry Hybrid XLE 2013 Toyota Highlander Hybrid 4WD 2013 Toyota Prius c One 2013 Toyota Prius Two

164

Project Overview: United Parcel Service's Second-Generation Hybrid-Electric Delivery Vans (Fact Sheet)  

DOE Green Energy (OSTI)

This fact sheet describes UPS second generation hybrid-electric delivery vehicles as compared to conventional delivery vehicles. Medium-duty commercial vehicles such as moving trucks, beverage-delivery trucks, and package-delivery vans consume almost 2,000 gal of fuel per year on average. United Parcel Service (UPS) operates hybrid-electric package-delivery vans to reduce the fuel use and emissions of its fleet. In 2008, the National Renewable Energy Laboratory's (NREL's) Fleet Test and Evaluation Team evaluated the first generation of UPS' hybrid delivery vans. These hybrid vans demonstrated 29%-37% higher fuel economy than comparable conventional diesel vans, which contributed to UPS' decision to add second-generation hybrid vans to its fleet. The Fleet Test and Evaluation Team is now evaluating the 18-month, in-service performance of 11 second-generation hybrid vans and 11 comparable conventional diesel vans operated by UPS in Minneapolis, Minnesota. The evaluation also includes testing fuel economy and emissions at NREL's Renewable Fuels and Lubricants (ReFUEL) Laboratory and comparing diesel particulate filter (DPF) regeneration. In addition, a followup evaluation of UPS' first-generation hybrid vans will show how those vehicles performed over three years of operation. One goal of this project is to provide a consistent comparison of fuel economy and operating costs between the second-generation hybrid vans and comparable conventional vans. Additional goals include quantifying the effects of hybridization on DPF regeneration and helping UPS select delivery routes for its hybrid vans that maximize the benefits of hybrid technology. This document introduces the UPS second-generation hybrid evaluation project. Final results will be available in mid-2012.

Not Available

2011-11-01T23:59:59.000Z

165

Full Hybrid: Overview  

NLE Websites -- All DOE Office Websites (Extended Search)

highlighted Stop/Start button banner graphic: blue bar highlighted Stop/Start button banner graphic: blue bar subbanner graphic: gray bar Overview Button highlighted Starting button Low Speed button Cruising button Passing button Braking button Stopped button OVERVIEW Full hybrids use a gasoline engine as the primary source of power, and an electric motor provides additional power when needed. In addition, full hybrids can use the electric motor as the sole source of propulsion for low-speed, low-acceleration driving, such as in stop-and-go traffic or for backing up. This electric-only driving mode can further increase fuel efficiency under some driving conditions. stage graphic: vertical blue rule Main stage: See through car with battery, engine, generator, power split device, and electric motor visible. The car is stopped at an intersection.

166

Pulsed hybrid field emitter  

DOE Patents (OSTI)

A hybrid emitter exploits the electric field created by a rapidly depoled ferroelectric material. Combining the emission properties of a planar thin film diamond emitter with a ferroelectric alleviates the present technological problems associated with both types of emitters and provides a robust, extremely long life, high current density cathode of the type required by emerging microwave power generation, accelerator technology and display applications. This new hybrid emitter is easy to fabricate and not susceptible to the same failures which plague microstructure field emitter technology. Local electrode geometries and electric field are determined independently from those for optimum transport and brightness preservation. Due to the large amount of surface charge created on the ferroelectric, the emitted electrons have significant energy, thus eliminating the requirement for specialized phosphors in emissive flat-panel displays. 11 figs.

Sampayan, S.E.

1998-03-03T23:59:59.000Z

167

Pulsed hybrid field emitter  

SciTech Connect

A hybrid emitter exploits the electric field created by a rapidly depoled ferroelectric material. Combining the emission properties of a planar thin film diamond emitter with a ferroelectric alleviates the present technological problems associated with both types of emitters and provides a robust, extremely long life, high current density cathode of the type required by emerging microwave power generation, accelerator technology and display applications. This new hybrid emitter is easy to fabricate and not susceptible to the same failures which plague microstructure field emitter technology. Local electrode geometries and electric field are determined independently from those for optimum transport and brightness preservation. Due to the large amount of surface charge created on the ferroelectric, the emitted electrons have significant energy, thus eliminating the requirement for specialized phosphors in emissive flat-panel displays.

Sampayan, Stephen E. (Manteca, CA)

1998-01-01T23:59:59.000Z

168

Full Hybrid: Overview  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

highlighted Starting button Low Speed button Cruising button Passing button Braking button Stopped button highlighted Starting button Low Speed button Cruising button Passing button Braking button Stopped button OVERVIEW Full hybrids use a gasoline engine as the primary source of power, and an electric motor provides additional power when needed. In addition, full hybrids can use the electric motor as the sole source of propulsion for low-speed, low-acceleration driving, such as in stop-and-go traffic or for backing up. This electric-only driving mode can further increase fuel efficiency under some driving conditions. stage graphic: vertical blue rule Main stage: See through car with battery, engine, generator, power split device, and electric motor visible. The car is stopped at an intersection. Main stage: See through car with battery, engine, generator, power split device, and electric motor visible. The car is stopped at an intersection.

169

Hybrid electroluminescent devices  

DOE Patents (OSTI)

A hybrid electroluminescent (EL) device comprises at least one inorganic diode element and at least one organic EL element that are electrically connected in series. The absolute value of the breakdown voltage of the inorganic diode element is greater than the absolute value of the maximum reverse bias voltage across the series. The inorganic diode element can be a power diode, a Schottky barrier diode, or a light-emitting diode.

Shiang, Joseph John (Niskayuna, NY); Duggal, Anil Raj (Niskayuna, NY); Michael, Joseph Darryl (Schenectady, NY)

2010-08-03T23:59:59.000Z

170

Mirror hybrid reactors  

SciTech Connect

The fusion-fission hybrid is a combination of the fusion and fission processes, having features which are complementary. Fission energy is running out of readily available fuel, and fusion has extra neutrons which can be used to breed that fission fuel. Fusion would have to take on an extra burden of radioactivity, but this early application would give fusion, which does not work well enough now to make power, practical experience which may accelerate development of pure fusion.

Moir, R.W.

1978-09-11T23:59:59.000Z

171

Analysis of village hybrid systems in Chile  

DOE Green Energy (OSTI)

Chile recently began a major rural electrification program to electrify those 240,000 families (about half of the rural people) who lack electricity access. In this paper, we discuss a pilot project to electrify three remote villages in Chile`s Region IX using wind/genset/battery hybrids. The intent of this project is to demonstrate the reliability and cost-effectiveness of wind/genset/battery hybrids and to encourage replication of these types of systems in Chile`s electrification program. For each village, electricity connections are planned for several residences, and also schools, health posts, community centers, or chapels. Projected average daily loads are small, ranging from 4 to 10 kWh. Using the optimization program HOMER and the simulation program Hybrid2, we evaluated options to maximize technical performance, minimize costs, and gain experience with a variety of systems and components. We find that wind/genset/battery hybrids will be able to provide cost-effective, reliable power for these sites. More importantly, their inherent flexibility allows for variations in load and resource without greatly affecting the cost of energy.

Lew, D J; Corbus, D; Holz, R [and others

1996-06-01T23:59:59.000Z

172

Dueco Plug-In Hybrid Engines  

Science Conference Proceedings (OSTI)

Dueco, a final stage manufacture of utility trucks, was awarded a congressionally directed cost shared contract to develop, test, validate, and deploy several PHEV utility trucks. Odyne will be the primary subcontractor responsible for all aspects of the hybrid system including its design and installation on a truck chassis. Key objectives in this program include developing a better understanding of the storage device and system capability; improve aspects of the existing design, optimization of system and power train components, and prototype evaluation. This two year project will culminate in the delivery of at least five vehicles for field evaluation.

Phillip Eidler

2011-09-30T23:59:59.000Z

173

Hybrid2: The hybrid power system simulation model  

DOE Green Energy (OSTI)

There is a large-scale need and desire for energy in remote communities, especially in the developing world; however the lack of a user friendly, flexible performance prediction model for hybrid power systems incorporating renewables hindered the analysis of hybrids (including wind turbines, PV, diesel generators, AC/DC energy storage) as options to conventional solutions. A user friendly model was needed with the versatility to simulate the many system locations, widely varying hardware configurations, and differing control options for potential hybrid power systems. To meet these ends, NREL and U. Mass. researchers developed the Hybrid2 software. This paper provides an overview of the capabilities, features, and functionality of the Hybrid2 code, discusses its validation and future plans. Model availability and technical support provided to Hybrid2 users are also discussed.

Baring-Gould, E I; Green, H J; van Dijk, V A.P. [National Renewable Energy Lab., Golden, CO (United States); Manwell, J F [Massachusetts Univ., Amherst, MA (United States). Renewable Energy Research Lab.

1996-07-01T23:59:59.000Z

174

Hybrid Electric Vehicles - HEV Modeling  

NLE Websites -- All DOE Office Websites (Extended Search)

Modeling Modeling Background Because of time and cost constraints, designers cannot build and test each of the many possible powertrain configurations for advanced vehicles. Thus, developing fuel cells and hybrid electric vehicles (HEVs) requires accurate, flexible simulation tools. Argonne undertook a collaborative effort to further develop Autonomie in collaboration with General Motors. Autonomie is sponsored by the U.S. Department of Energy (DOE) Vehicle Technologies Program. Autonomie is a Plug-and-Play Powertrain and Vehicle Model Architecture and Development Environment to support the rapid evaluation of new powertrain/propulsion technologies for improving fuel economy through virtual design and analysis in a math-based simulation environment. Autonomie is an open architecture to support the rapid integration and analysis of powertrain/propulsion systems and technologies for rapid technology sorting and evaluation of fuel economy improvement under dynamic/transient testing conditions. The capability to sort technologies rapidly in a virtual design environment results in faster improvements in real-world fuel consumption by reducing the time necessary to develop and bring new technologies onto our roads.

175

Solar thermal electric hybridization issues  

DOE Green Energy (OSTI)

Solar thermal electric systems have an advantage over many other renewable energy technologies because the former use heat as an intermediate energy carrier. This is an advantage as it allows for a relatively simple method of hybridization by using heat from fossil-fuel. Hybridization of solar thermal electric systems is a topic that has recently generated significant interest and controversy and has led to many diverse opinions. This paper discusses many of the issues associated with hybridization of solar thermal electric systems such as what role hybridization should play; how it should be implemented; what are the efficiency, environmental, and cost implications; what solar fraction is appropriate; how hybrid systems compete with solar-only systems; and how hybridization can impact commercialization efforts for solar thermal electric systems.

Williams, T A; Bohn, M S; Price, H W

1994-10-01T23:59:59.000Z

176

Hybrid Geothermal Heat Pump Systems  

Science Conference Proceedings (OSTI)

Hybrid geothermal heat pump systems offer many of the benefits of full geothermal systems but at lower installed costs. A hybrid geothermal system combines elements of a conventional water loop heat pump system in order to reduce the geothermal loop heat exchanger costs, which are probably the largest cost element of a geothermal system. These hybrid systems have been used successfully where sufficient ground space to install large heat exchangers for full geothermal options was unavailable, or where the...

2009-12-21T23:59:59.000Z

177

Argonne Transportation - Plug-in Hybrid Electric Vehicle Research  

NLE Websites -- All DOE Office Websites (Extended Search)

Plug-in Hybrid Electric Vehicle Research Capabilities at Argonne National Laboratory and Idaho National Laboratory Plug-in Hybrid Electric Vehicle Research Capabilities at Argonne National Laboratory and Idaho National Laboratory Prius testing by Argonne researchers. The U.S. Department of Energy's (DOE's) FreedomCAR and Vehicle Technologies (FCVT) Program is actively evaluating plug-in hybrid electric vehicle (PHEV) technology and researching the most critical technical barriers to commercializing PHEVs. Argonne National Laboratory, working together with Idaho National Laboratory, leads DOE's efforts to evaluate PHEVs and PHEV technology with the nationÂ’s best vehicle technology evaluation tools and expertise. These two national laboratories are Centers for Excellence that combine state-of-the-art facilities; world-class expertise; long-term collaborative relationships with other DOE national laboratories, industry, and academia;

178

Energy Basics: Hybrid Electric Vehicles  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

& Fuels Printable Version Share this resource Fuels Vehicles Electric Vehicles Flexible Fuel Vehicles Fuel Cell Vehicles Hybrid Electric Vehicles Natural Gas Vehicles Propane...

179

Electric and Hybrid Vehicle System Research and Development Project: Hybrid Vehicle Potential Assessment. Volume VI. Cost analysis  

DOE Green Energy (OSTI)

The purpose of the cost analysis is to determine the economic feasibility of a variety of hybrid vehicles with respect to conventional vehicles specifically designed for the same duty cycle defined by the mission analysis. Several different hybrid configurations including parallel, parallel-flywheel, and series vehicles were evaluated. The ramifications of incorporating examples of advanced batteries, these being the advanced lead-acid, nickel-zinc, and sodium sulfur were also investigated. Vehicles were specifically designed with these batteries and for the driving cycles specified by the mission. Simulated operation on the missions yielded the energy consumption (petroleum and/or electricity) over the driving cycles. It was concluded that: in the event that gasoline prices reach $2.50 to $3.00/gal, hybrid vehicles in many applications will become economically competitive with conventional vehicles without subsidization; in some commercial applications hybrid vehicles could be economically competitive, when the gasoline price ranges from $1.20 to $1.50/gal. The cost per kWh per cycle of the advanced batteries is much more important economically than the specific energy; the series hybrid vehicles were found to be more expensive in comparison to the parallel or parallel-flywheel hybrids when designed as passenger vehicles; and hybrid vehicles designed for private use could become economically competitive and displace up to 50% of the fuel normally used on that mission if subsidies of $500 to $2000 were supplied to the owner/operator. (LCL)

Hardy, K.S.

1979-09-30T23:59:59.000Z

180

Hybrid vehicle potential assessment. Volume 7. Hybrid vehicle review  

DOE Green Energy (OSTI)

Review of hybrid vehicles (HVs) built during the past ten years or planned to be built in the near future is presented. An attempt is made to classify and analyze these vehicles to get an overall picture of their key characteristics. The review includes on-road hybrid passenger cars, trucks, vans, and buses.

Leschly, K.O.

1979-09-30T23:59:59.000Z

Note: This page contains sample records for the topic "hybrid tractor evaluation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Hybrid solar lighting distribution systems and components  

Science Conference Proceedings (OSTI)

A hybrid solar lighting distribution system and components having at least one hybrid solar concentrator, at least one fiber receiver, at least one hybrid luminaire, and a light distribution system operably connected to each hybrid solar concentrator and each hybrid luminaire. A controller operates all components.

Muhs, Jeffrey D. (Lenoir City, TN); Earl, Dennis D. (Knoxville, TN); Beshears, David L. (Knoxville, TN); Maxey, Lonnie C. (Powell, TN); Jordan, John K. (Oak Ridge, TN); Lind, Randall F. (Lenoir City, TN)

2011-07-05T23:59:59.000Z

182

Hybrid solar lighting systems and components  

DOE Patents (OSTI)

A hybrid solar lighting system and components having at least one hybrid solar concentrator, at least one fiber receiver, at least one hybrid luminaire, and a light distribution system operably connected to each hybrid solar concentrator and each hybrid luminaire. A controller operates each component.

Muhs, Jeffrey D. (Lenoir City, TN); Earl, Dennis D. (Knoxville, TN); Beshears, David L. (Knoxville, TN); Maxey, Lonnie C. (Powell, TN); Jordan, John K. (Oak Ridge, TN); Lind, Randall F. (Lenoir City, TN)

2007-06-12T23:59:59.000Z

183

Effects of Vehicle Image in Gasoline-Hybrid Electric Vehicles  

E-Print Network (OSTI)

The Images of Hybrid Vehicles Each of the householdsbetween hybrid and non-hybrid vehicles was observed in smallowned Honda Civic Hybrids, vehicles that are virtually

Heffner, Reid R.; Kurani, Ken; Turrentine, Tom

2005-01-01T23:59:59.000Z

184

Conceptual innovations in hybrid reactors  

SciTech Connect

A number of innovations in the conception of fusion-fission hybrid reactors, including the blanket, the fusion driver, the coupling of the fusion and the fission components as well as the application of hybrid reactors are described, and their feasibility assessed.

Greenspan, E.; Miley, G.H.

1980-01-01T23:59:59.000Z

185

Hybrids Plus | Open Energy Information  

Open Energy Info (EERE)

Hybrids Plus Hybrids Plus Jump to: navigation, search Name Hybrids Plus Address 3245 Prarie Ave Place Boulder, Colorado Zip 80301 Sector Vehicles Product Plug in Electric Hybrid Vehicle conversions, chargers, battery systems Website http://www.eetrex.com/ Coordinates 40.022143°, -105.250981° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":40.022143,"lon":-105.250981,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

186

Issue 5: High Interest in Hybrid Cars  

E-Print Network (OSTI)

2005). “High Interest in Hybrid Cars. ” SCS Fact Sheet, Vol.May 2005 High Interest in Hybrid Cars I NTRODUCTION PublicThe unique features of a hybrid car mean that it is more

Ong, Paul M.; Haselhoff, Kim

2005-01-01T23:59:59.000Z

187

Quantifying the benefits of hybrid vehicles  

E-Print Network (OSTI)

secrets, but the price of hybrid cars and trucks are betweenCosts of hybrid vehicles Depending on whether a car companydiesel-hybrid prototypes that attained 70 MPG (Green Car

Turrentine, Tom; Delucchi, Mark; Heffner, Reid R.; Kurani, Kenneth S; Sun, Yongling

2006-01-01T23:59:59.000Z

188

Quantifying the benefits of hybrid vehicles  

E-Print Network (OSTI)

The Emergence of Hybrid Vehicles: Ending oil’s strangleholdthe benefits of hybrid vehicles Dr. Thomas Turrentine Dr.the benefits of hybrid vehicles Report prepared for CSAA Dr.

Turrentine, Tom; Delucchi, Mark; Heffner, Reid R.; Kurani, Kenneth S; Sun, Yongling

2006-01-01T23:59:59.000Z

189

Hybrid powertrain controller  

DOE Patents (OSTI)

A hybrid powertrain for a vehicle comprising a diesel engine and an electric motor in a parallel arrangement with a multiple ratio transmission located on the torque output side of the diesel engine, final drive gearing connecting drivably the output shaft of transmission to traction wheels of the vehicle, and an electric motor drivably coupled to the final drive gearing. A powertrain controller schedules fuel delivered to the diesel engine and effects a split of the total power available, a portion of the power being delivered by the diesel and the balance of the power being delivered by the motor. A shifting schedule for the multiple ratio transmission makes it possible for establishing a proportional relationship between accelerator pedal movement and torque desired at the wheels. The control strategy for the powertrain maintains drivability of the vehicle that resembles drivability of a conventional spark ignition vehicle engine powertrain while achieving improved fuel efficiency and low exhaust gas emissions.

Jankovic, Miroslava (Birmingham, MI); Powell, Barry Kay (Belleville, MI)

2000-12-26T23:59:59.000Z

190

2011 Hyundai Sonata Hybrid  

NLE Websites -- All DOE Office Websites (Extended Search)

Hyundai Sonata Hybrid Hyundai Sonata Hybrid Test cell location 2WD Vehicle Setup Information Downloadable Dynamometer Database (D 3 )- Test Summary Sheet Vehicle architecture P2 HEV Vehicle Dynamometer Input Document date 8/7/2013 Advanced Powertrain Research Facility Test weight [lb] Target A [lb] 3750 26.8 Target B [lb/mph] Target C [lb/mph^2] 0.15 0.0145 Revision number 3 Notes: Test Fuel Information Fuel type EPA Tier II EEE Gasoline Fuel density [g/ml] Fuel Net HV [BTU/lbm] 0.742 18202 T e s t I D [ # ] C y c l e C o l d s t a r t ( C S t ) H o t s t a r t [ H S t ] D a t e T e s t C e l l T e m p [ C ] T e s t C e l l R H [ % ] T e s t C e l l B a r o [ i n / H g ] V e h i c l e c o o l i n g f a n s p e e d : S p e e d M a t c h [ S M ] o r c o n s t a n t s p e e d [ C S ] S o l a r L a m p s [ W / m 2 ] V e i c l e C l i m a t e C o n t r o l s e t t i n g s H o o d P o s i t i o n [ U p ] o r [ C l o s e d ] W i n d o w P o s i t i o n [ C l o s e d ] o r [ D o w n ] C y c l e D i s t a n c e [ m i ] C

191

MERCURY CONTROL WITH ADVANCED HYBRID PARTICULATE COLLECTOR  

SciTech Connect

This project was awarded under U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL) Program Solicitation DE-PS26-00NT40769 and specifically addressed Technical Topical Area 4-Testing Novel and Less Mature Control Technologies on Actual Flue Gas at the Pilot Scale. The project team included the Energy & Environmental Research Center (EERC) as the main contractor; W.L. Gore & Associates, Inc., as a technical and financial partner; and the Big Stone Power Plant operated by Otter Tail Power Company, host for the field-testing portion of the research. Since 1995, DOE has supported development of a new concept in particulate control called the advanced hybrid particulate collector (AHPC). The AHPC has been licensed to W.L. Gore & Associates, Inc., and has been marketed as the Advanced Hybrid{trademark} filter by Gore. The Advanced Hybrid{trademark} filter combines the best features of electrostatic precipitators (ESPs) and baghouses in a unique configuration, providing major synergism between the two collection methods, both in the particulate collection step and in the transfer of dust to the hopper. The Advanced Hybrid{trademark} filter provides ultrahigh collection efficiency, overcoming the problem of excessive fine-particle emissions with conventional ESPs, and it solves the problem of reentrainment and re-collection of dust in conventional baghouses. The Advanced Hybrid{trademark} filter also appears to have unique advantages for mercury control over baghouses or ESPs as an excellent gas--solid contactor. The objective of the project was to demonstrate 90% total mercury control in the Advanced Hybrid{trademark} filter at a lower cost than current mercury control estimates. The approach included bench-scale batch tests, larger-scale pilot testing with real flue gas on a coal-fired combustion system, and field demonstration at the 2.5-MW (9000-acfm) scale at a utility power plant to prove scale-up and demonstrate longer-term mercury control. An additional task was included in this project to evaluate mercury oxidation upstream of a dry scrubber by using mercury oxidants. This project demonstrated at the pilot-scale level a technology that provides a cost-effective technique to control mercury and, at the same time, greatly enhances fine particulate collection efficiency. The technology can be used to retrofit systems currently employing inefficient ESP technology as well as for new construction, thereby providing a solution for improved fine particulate control combined with effective mercury control for a large segment of the U.S. utility industry as well as other industries.

Ye Zhuang; Stanley J. Miller

2005-05-01T23:59:59.000Z

192

Advanced Coal Wind Hybrid: Economic Analysis  

E-Print Network (OSTI)

of Figures Figure ES-1. Advanced Coal Wind Hybrid: Basicviii Figure 1. Advanced-Coal Wind Hybrid: Basic29 Figure 9. Sensitivity to Coal

Phadke, Amol

2008-01-01T23:59:59.000Z

193

Advanced Coal Wind Hybrid: Economic Analysis  

E-Print Network (OSTI)

of Figures Figure ES-1. Advanced Coal Wind Hybrid: Basicviii Figure 1. Advanced-Coal Wind Hybrid: Basic21 Figure 6. Comparison of ACWH and CCGT-Wind

Phadke, Amol

2008-01-01T23:59:59.000Z

194

Quantifying the benefits of hybrid vehicles  

E-Print Network (OSTI)

century. Hybrid electric vehicles (HEVs) reduce emissionsas plug-in HEVs and full electric vehicles to market. In theon their design, hybrid electric vehicles employ electric

Turrentine, Tom; Delucchi, Mark; Heffner, Reid R.; Kurani, Kenneth S; Sun, Yongling

2006-01-01T23:59:59.000Z

195

Advanced Vehicle Testing Activity: Chevrolet Silverado Hybrid...  

NLE Websites -- All DOE Office Websites (Extended Search)

Chevrolet Silverado Hybrid Electric Vehicle Accelerated Reliability Testing - April 2009 to someone by E-mail Share Advanced Vehicle Testing Activity: Chevrolet Silverado Hybrid...

196

Calibration of Hygrometers with the Hybrid Humidity ...  

Science Conference Proceedings (OSTI)

... Hybrid Humidity Generator ... The HHG combines the two-pressure and divided-flow humidity generation techniques (hence the name “hybrid”). ...

2012-05-22T23:59:59.000Z

197

Advanced Coal Wind Hybrid: Economic Analysis  

NLE Websites -- All DOE Office Websites (Extended Search)

Coal Wind Hybrid: Economic Analysis Title Advanced Coal Wind Hybrid: Economic Analysis Publication Type Report LBNL Report Number LBNL-1248E Year of Publication 2008 Authors...

198

Advanced Coal Wind Hybrid: Economic Analysis  

NLE Websites -- All DOE Office Websites (Extended Search)

Advanced Coal Wind Hybrid: Economic Analysis Title Advanced Coal Wind Hybrid: Economic Analysis Publication Type Report Year of Publication 2008 Authors Phadke, Amol, Charles A....

199

Vehicle Technologies Office: Hybrid and Vehicle Systems  

NLE Websites -- All DOE Office Websites (Extended Search)

Hybrid and Vehicle Systems Hybrid and vehicle systems research provides an overarching vehicle systems perspective to the technology research and development (R&D) activities of...

200

Just the Basics - Hybrid Electric Vehicles  

NLE Websites -- All DOE Office Websites (Extended Search)

Hybrid Electric Vehicles Hybrid electric vehicles (HEVs) offer reduced pollution and improved fuel economy. That's why the government and auto- makers are anxious to introduce a...

Note: This page contains sample records for the topic "hybrid tractor evaluation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

2010 Hyundai LPI Hybrid Test Cell Location  

NLE Websites -- All DOE Office Websites (Extended Search)

Hyundai LPI Hybrid Test Cell Location APRF- 4WD Vehicle Setup Information Downloadable Dynamometer Database (D 3 )- Test Summary Sheet Vehicle Architecture Alternative Fuel Hybrid...

202

Development of a Novel Air Hybrid Engine.  

E-Print Network (OSTI)

??An air hybrid vehicle is an alternative to the electric hybrid vehicle that stores the kinetic energy of the vehicle during braking in the form… (more)

Fazeli, Amir

2011-01-01T23:59:59.000Z

203

Hybrid photovoltaic/thermal solar energy system  

DOE Green Energy (OSTI)

Heating and cooling systems that use hybrid solar energy collectors (combination photovoltaic-thermal) have the potential for considerable energy savings, particularly when the system includes a heat pump. Economic evaluations show that photovoltaic systems are potentially most economical, but results depend critically on future collector costs as well as energy prices. Results are based on a specially developed computer program that predicted the total auxiliary energy required for five different solar heating/cooling systems. Performance calculations for a modeled residence and small office building were made using meteorological data from four geographic locations. Annual system costs were also calculated.

Kern, E.C. Jr.; Russell, M.C.

1978-03-27T23:59:59.000Z

204

Extending the lifetime of fuel cell based hybrid systems  

E-Print Network (OSTI)

Fuel cells are clean power sources that have much higher energy densities and lifetimes compared to batteries. However, fuel cells have limited load following capabilities and cannot be efficiently utilized if used in isolation. In this work, we consider a hybrid system where a fuel cell based hybrid power source is used to provide power to a DVFS processor. The hybrid power source consists of a room temperature fuel cell operating as the primary power source and a Li-ion battery (that has good load following capability) operating as the secondary source. Our goal is to develop polices to extend the lifetime of the fuel cell based hybrid system. First, we develop a charge based optimization framework which minimizes the charge loss of the hybrid system (and not the energy consumption of the DVFS processor). Next, we propose a new algorithm to minimize the charge loss by judiciously scaling the load current. We compare the performance of this algorithm with one that has been optimized for energy, and demonstrate its superiority. Finally, we evaluate the performance of the hybrid system under different system configurations and show how to determine the best combination of fuel cell size and battery capacity for a given embedded application.

Jianli Zhuo; Chaitali Chakrabarti; Naehyuck Chang; Sarma Vrudhula

2006-01-01T23:59:59.000Z

205

Economic analysis of PV hybrid power system: Pinnacles National Monument  

DOE Green Energy (OSTI)

PV hybrid electric power systems can offer an economically competitive alternative to engine generator (genset) systems in many off-grid applications. Besides the obvious `green` advantages of producing less noise and emissions, the PV hybrid can, in some cases, offer a lower life-cycle cost (LCC) then the genset. This paper evaluates the LCC of the 9.6 kWp PV hybrid power system installed by the National Park Services (NPS) at Pinnacles National Monument, CA. NPS motivation for installation of this hybrid was not based on economics, but rather the need to replace two aging diesel gensets with an alternative that would be quieter, fuel efficient, and more in keeping with new NPS emphasis on sustainable design and operations. In fact, economic analysis shows a lower 20-year LCC for the installed PV hybrid than for simple replacement of the two gensets. The analysis projects are net savings by the PV hybrid system of $83,561 and over 162,000 gallons of propane when compared with the genset-only system. This net savings is independent of the costs associated with environmental emissions. The effects of including emissions costs, according to NPS guidelines, is also discussed. 5 refs., 2 figs., 3 tabs.

Rosenthal, A.; Durand, S. [Southwest Technology Development Institute, Las Cruces, NM (United States); Thomas, M.; Post, H. [Sandia National Labs., Albuquerque, NM (United States)

1997-11-01T23:59:59.000Z

206

Hybrid lighting: Illuminating our future  

SciTech Connect

Hybrid lighting is a combination of natural and artificial illumination to be used indoors for all lighting needs. Ideally, hybrid lighting is effectively indistinguishable from standard artificial lighting except in quality and cost, where it will likely be an improvement. Hybrid lighting systems are produced by a combination of four technologies: collecting natural light, generating artificial light, transporting and distributing light to where it is needed, and controlling the amounts of both natural and artificial light continuously during usage. Lighting demands a large fraction of our energy needs. If we can control or decrease this demand, we are able to accommodate societal growth without energy demand growth.

Cates, M.R.

1996-12-31T23:59:59.000Z

207

Hybrid Vehicle Program. Final report  

DOE Green Energy (OSTI)

This report summarizes the activities on the Hybrid Vehicle Program. The program objectives and the vehicle specifications are reviewed. The Hybrid Vehicle has been designed so that maximum use can be made of existing production components with a minimum compromise to program goals. The program status as of the February 9-10 Hardware Test Review is presented, and discussions of the vehicle subsystem, the hybrid propulsion subsystem, the battery subsystem, and the test mule programs are included. Other program aspects included are quality assurance and support equipment. 16 references, 132 figures, 47 tables.

None

1984-06-01T23:59:59.000Z

208

NREL: Fleet Test and Evaluation - Research and Development  

NLE Websites -- All DOE Office Websites (Extended Search)

Research and Development Research and Development The Fleet Test and Evaluation Team conducts research that supports the development and deployment of alternative fuel and advanced vehicle technologies in medium- and heavy-duty fleet vehicles. Technology evaluation projects focus on drive cycle analysis, hybrid electric vehicles, all-electric vehicles, truck stop electrification, and alternative fuels. Learn more about the team's project areas: Fleet DNA: Vehicle Drive Cycle Analysis Hybrid Electric Drive Systems Electric and Plug-in Hybrid Electric Drive Systems Hydraulic Hybrid Drive Systems Truck Stop Electrification Alternative Fuels Truck Efficiency Printable Version Fleet Test and Evaluation Home Research & Development Vehicle Drive Cycle Analysis Hybrid Electric Drive Systems

209

Alternative Fuels Data Center: Heavy-Duty Vehicle and Engine...  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

T270 hybrid Applications: Tractor, Vocational truck Fuel Type: Hybrid - Diesel Electric Power Source(s): Paccar - PX-6 6.7L Hybrid System(s): Eaton - Diesel Electric Hybrid...

210

Hybrid Fiber Optics  

SciTech Connect

Instruments and devices based on optical fiber were originally simple and passive. That has changed. A variety of devices uses optical fiber for sensing, communications and various optoelectronic functions. This paper discusses the creation of a hybrid optical fiber that incorporates not just the light transmission function but other types of materials and new multiple fiber arrangements. Recent experiences with a fiber draw tower reveal new possibilities for achieving multifunctional devices able to perform diverse instrumentation sensing applications. This is achievable even with feature sizes, when desired, on the nanoscale. For instance, fiber comprised of one or more light guides and one or more electrically conducting wires is feasible. This combination of optical fiber and metal wire may be termed a wiber . The wiber could determine temperature and proximity to surfaces, detect radio-frequency radiation, and provide electrical power. At the same time, a wiber would have the capability to simultaneously transmit light where the light is utilized to sense temperature and proximity and give illumination. There are many possible uses--depending on design and configuration--cutting across many technologies and programs.

Allison, Stephen W [ORNL; Simpson, John T [ORNL; Gillies, George [ORNL

2010-01-01T23:59:59.000Z

211

Full Hybrid: Starting  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

highlighted Low Speed button Cruising button Passing button Braking button Stopped button highlighted Low Speed button Cruising button Passing button Braking button Stopped button STARTING When a full hybrid vehicle is initially started, the battery typically powers all accessories. The gasoline engine only starts if the battery needs to be charged or the accessories require more power than available from the battery. stage graphic: vertical blue rule Main stage: See through car with battery, engine, generator, power split device, and electric motor visible. the car is stopped at an intersection. Main stage: See through car with battery, engine, generator, power split device, and electric motor visible. the car is stopped at an intersection. Battery (highlighted): The battery stores energy generated from the gasoline engine or, during regenerative braking, from the electric motor. Since the battery powers the vehicle at low speeds, it is larger and holds much more energy than batteries used to start conventional vehicles. Main stage: See through car with battery, engine, generator, power split device, and electric motor visible. the car is stopped at an intersection. Main stage: See through car with battery, engine, generator, power split device, and electric motor visible. the car is stopped at an intersection.

212

ADVANCED HYBRID PARTICULATE COLLECTOR  

SciTech Connect

A new concept in particulate control, called an advanced hybrid particulate collector (AHPC), is being developed under funding from the US Department of Energy. The AHPC combines the best features of electrostatic precipitators (ESPs) and baghouses in an entirely novel manner. The AHPC concept combines fabric filtration and electrostatic precipitation in the same housing, providing major synergism between the two methods, both in the particulate collection step and in transfer of dust to the hopper. The AHPC provides ultrahigh collection efficiency, overcoming the problem of excessive fine-particle emissions with conventional ESPs, and solves the problem of reentrainment and recollection of dust in conventional baghouses. Phase I of the development effort consisted of design, construction, and testing of a 5.7-m{sup 3}/min (200-acfm) working AHPC model. Results from both 8-hour parametric tests and 100-hour proof-of-concept tests with two different coals demonstrated excellent operability and greater than 99.99% fine-particle collection efficiency.

Stanley J. Miller; Grant L. Schelkoph; Grant E. Dunham

2000-12-01T23:59:59.000Z

213

NREL: Learning - Hybrid Electric Vehicles  

NLE Websites -- All DOE Office Websites (Extended Search)

Hybrid Electric Vehicles Hybrid Electric Vehicles Photo of the front and part of the side of a bus parked at the curb of a city street with tall buildings in the background. This diesel hybrid electric bus operated by the Metropolitan Transit Authority, New York City Transit, was part of a test study that recently investigated the fuel efficiency and reliability of these buses. Credit: Leslie Eudy Today's hybrid electric vehicles (HEVs) range from small passenger cars to sport utility vehicles (SUVs) and large trucks. Though they often look just like conventional vehicles, HEVs usually include an electric motor as well as a small internal combustion engine (ICE). This combination provides greater fuel economy and fewer emissions than most conventional ICE vehicles do. HEVs are powered by two energy sources: an energy conversion unit, such as

214

Physics Out Loud - Hybrid Meson  

NLE Websites -- All DOE Office Websites (Extended Search)

Hadron Previous Video (Hadron) Physics Out Loud Main Index Next Video (Laser) Laser Hybrid Meson We're well on our way in exploring how the strong force glues the nucleus together....

215

Global optimization of hybrid systems  

E-Print Network (OSTI)

Systems that exhibit both discrete state and continuous state dynamics are called hybrid systems. In most nontrivial cases, these two aspects of system behavior interact to such a significant extent that they cannot be ...

Lee, Cha Kun

2006-01-01T23:59:59.000Z

216

Hybrid Fuel Cell Technology Overview  

SciTech Connect

For the purpose of this STI product and unless otherwise stated, hybrid fuel cell systems are power generation systems in which a high temperature fuel cell is combined with another power generating technology. The resulting system exhibits a synergism in which the combination performs with an efficiency far greater than can be provided by either system alone. Hybrid fuel cell designs under development include fuel cell with gas turbine, fuel cell with reciprocating (piston) engine, and designs that combine different fuel cell technologies. Hybrid systems have been extensively analyzed and studied over the past five years by the Department of Energy (DOE), industry, and others. These efforts have revealed that this combination is capable of providing remarkably high efficiencies. This attribute, combined with an inherent low level of pollutant emission, suggests that hybrid systems are likely to serve as the next generation of advanced power generation systems.

None available

2001-05-31T23:59:59.000Z

217

NIST 'Hybrid Metrology' Method Could Improve Computer ...  

Science Conference Proceedings (OSTI)

NIST 'Hybrid Metrology' Method Could Improve Computer Chips. From NIST Tech Beat: September 5, 2012. ...

2012-09-06T23:59:59.000Z

218

New York City Transit Diesel Hybrid-Electric Buses Final Results: DOE/ NREL  

Open Energy Info (EERE)

Transit Diesel Hybrid-Electric Buses Final Results: DOE/ NREL Transit Diesel Hybrid-Electric Buses Final Results: DOE/ NREL Transit Bus Evaluation Project Jump to: navigation, search Name New York City Transit Diesel Hybrid-Electric Buses Final Results: DOE/ NREL Transit Bus Evaluation Project Agency/Company /Organization Department of Energy Partner National Renewable Energy Laboratory Batelle"National Renewable Energy Laboratory Batelle" cannot be used as a page name in this wiki. Focus Area Transportation Phase Bring the Right People Together, Determine Baseline, Evaluate Options, Develop Finance and Implement Projects Resource Type Guide/manual Availability Publicly available--Free Publication Date 7/1/2002 Website http://www.nrel.gov/docs/fy02o Locality New York City References New York City Transit Diesel Hybrid-Electric Buses Final Results: DOE/ NREL Transit Bus Evaluation Project[1]

219

ANALYSIS OF CONTROL SYSTEMS FOR VEHICLE HYBRID POWERTRAINS  

E-Print Network (OSTI)

Abstract. Ecological and socioeconomic factors determine high interest in the development of pollution-free vehicles. At present use of electro-vehicles is suppressed by a number of technological factors. Vehicles with alternative powertrains are transitional stage between development of pollution-free vehicles and vehicles with conventional internal combustion engine. According to these aspects the investigation on conventional hybrid drives and their control systems is carried out in the article. The equations that allow evaluating effectiveness of regenerative braking for different variants of hybrid drive are given. The AMESim software is used as the modeling environment, in which models of hybrid vehicles are developed and the results of virtual simulation are analyzed. Also a number of recommendations for increasing of regenerative braking effectiveness are given.

Siarhei Kliauzovich

2007-01-01T23:59:59.000Z

220

Hybrid energy system cost analysis: San Nicolas Island, California  

DOE Green Energy (OSTI)

This report analyzes the local wind resource and evaluates the costs and benefits of supplementing the current diesel-powered energy system on San Nicolas Island, California (SNI), with wind turbines. In Section 2.0 the SNI site, naval operations, and current energy system are described, as are the data collection and analysis procedures. Section 3.0 summarizes the wind resource data and analyses that were presented in NREL/TP 442-20231. Sections 4.0 and 5.0 present the conceptual design and cost analysis of a hybrid wind and diesel energy system on SNI, with conclusions following in Section 6. Appendix A presents summary pages of the hybrid system spreadsheet model, and Appendix B contains input and output files for the HYBRID2 program.

Olsen, T.L.; McKenna, E.

1996-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "hybrid tractor evaluation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Scoping studies of /sup 233/U breeding fusion fission hybrid  

SciTech Connect

Neutronic calculations have been carried out in order to design a laser fusion driven hybrid blanket which maximizes /sup 233/U production per unit of thermal energy (greater than or equal to 1 kg/MW/sub T/-year) with acceptable fusion energy multiplication (M/sub F/ approximately 4). Two hybrid blankets, a thorium and a uranium-thorium blanket, are discussed in detail and their performance is evaluated by incorporating them into an existing hybrid design (the LLL/Bechtel design). The overall performance of the two laser fusion driven /sup 233/U producers is discussed and estimates are given of (1) the number of equivalent thermal power fission reactors (LWR, HWR, SSCR and HTGR) that these fusion breeders can fuel, (2) their capital cost, and (3) the cost of electricity in the combined fusion breder-converter reactor scenario.

Maniscalco, J.A.; Hansen, L.F.; Allen, W.O.

1978-05-01T23:59:59.000Z

222

Neutron diagnostics for mirror hybrids  

SciTech Connect

Fusion-fission (FuFi) hybrids will need instrumentation to diagnose the deuteriumtritium plasma, whose 14-MeV neutron emission is the driver of the sub-critical fission core. While the fission neutron yield rate (Y{sub fi} and hence power P{sub fi}) can be monitored with standard instrumentation, fusion plasmas in hybrids require special diagnostics where the determination of Y{sub th} ({proportional_to}P{sub fu}) is a challenge. Information on Y{sub fu} is essential for assessing the fusion plasma performance which together with Y{sub fi} allows for the validation of the neutron multiplication factor (k) of the subcritical fission core. Diagnostics for hybrid plasmas are heuristically discussed with special reference to straight field line mirror (SFLM). Relevant DT plasma experience from JET and plans for ITER in the main line of fusion research were used as input. It is shown that essential SFLM plasma information can potentially be obtained with proposed instrumentation, but the state of the hybrid plasma must be predictably robust as derived from fully diagnosed dedicated experiments without interface restrictions of the hybrid application.

Kaellne, Jan; Noack, Klaus; Agren, Olov; Gorini, Giuseppe; Tardocchi, Marco; Grosso, Giovanni [Department of Engineering Sciences, Uppsala University, Box 256, SE-751 21 Uppsala (Sweden); Universita degli Studi di Milano - Bicocca, Dip. di Fisica 'G. Occhialini', Piazza della Scienza 3, 20126, Milan (Italy)

2012-06-19T23:59:59.000Z

223

Design of isolated renewable hybrid power systems  

Science Conference Proceedings (OSTI)

Isolated electrical power generating units can be used as an economically viable alternative to electrify remote villages where grid extension is not feasible. One of the options for building isolated power systems is by hybridizing renewable power sources like wind, solar, micro-hydro, etc. along with appropriate energy storage. A method to optimally size and to evaluate the cost of energy produced by a renewable hybrid system is proposed in this paper. The proposed method, which is based on the design space approach, can be used to determine the conditions for which hybridization of the system is cost effective. The simple and novel methodology, proposed in this paper, is based on the principles of process integration. It finds the minimum battery capacity when the availability and ratings of various renewable resources as well as load demand are known. The battery sizing methodology is used to determine the sizing curve and thereby the feasible design space for the entire system. Chance constrained programming approach is used to account for the stochastic nature of the renewable energy resources and to arrive at the design space. The optimal system configuration in the entire design space is selected based on the lowest cost of energy, subject to a specified reliability criterion. The effects of variation of the specified system reliability and the coefficient of correlation between renewable sources on the design space, as well as the optimum configuration are also studied in this paper. The proposed method is demonstrated by designing an isolated power system for an Indian village utilizing wind-solar photovoltaic-battery system. (author)

Sreeraj, E.S.; Chatterjee, Kishore [Department of Electrical Engineering, Indian Institute of Technology Bombay, Mumbai 400 076 (India); Bandyopadhyay, Santanu [Department of Energy Science and Engineering, Indian Institute of Technology Bombay, Mumbai 400 076 (India)

2010-07-15T23:59:59.000Z

224

Early Results from DOE/NREL Transit Bus Evaluations  

DOE Green Energy (OSTI)

Presentation at 2005 American Public Transportation Association Conference provides status of NREL/DOE evaluations of New York City Transit and King County Metro hybrid electric buses.

Eudy, L.; Chandler, K.

2005-05-01T23:59:59.000Z

225

Compositional Variation Within Hybrid Nanostructures  

NLE Websites -- All DOE Office Websites (Extended Search)

Compositional Variation Within Hybrid Nanostructures Print Compositional Variation Within Hybrid Nanostructures Print The inherently high surface area of bimetallic nanoparticles makes them especially attractive materials for heterogeneous catalysis. The ability to selectively grow these and other types of nanoparticles on a desired surface is ideal for the fabrication of higher-order nanoscale architectures. However, the growth mechanism for bimetallic nanoparticles on a surface is expected to be quite different than that for free particles in solution. The altered growth process can lead to modulations in stoichiometry, elemental homogeneity, and surface structure, all of which can profoundly affect the catalytic or magnetic properties of the bimetallic nanoparticles. Now, researchers have experimentally observed these subtle structural differences through x-ray absorption spectroscopic studies at ALS Beamline 10.3.2. The results illustrate how directed nanoparticle growth on specific surfaces can lead to hybrid nanomaterials with a structurally different bimetallic component than its unhybridized counterpart.

226

Compositional Variation Within Hybrid Nanostructures  

NLE Websites -- All DOE Office Websites (Extended Search)

Compositional Variation Within Hybrid Nanostructures Print Compositional Variation Within Hybrid Nanostructures Print The inherently high surface area of bimetallic nanoparticles makes them especially attractive materials for heterogeneous catalysis. The ability to selectively grow these and other types of nanoparticles on a desired surface is ideal for the fabrication of higher-order nanoscale architectures. However, the growth mechanism for bimetallic nanoparticles on a surface is expected to be quite different than that for free particles in solution. The altered growth process can lead to modulations in stoichiometry, elemental homogeneity, and surface structure, all of which can profoundly affect the catalytic or magnetic properties of the bimetallic nanoparticles. Now, researchers have experimentally observed these subtle structural differences through x-ray absorption spectroscopic studies at ALS Beamline 10.3.2. The results illustrate how directed nanoparticle growth on specific surfaces can lead to hybrid nanomaterials with a structurally different bimetallic component than its unhybridized counterpart.

227

Compositional Variation Within Hybrid Nanostructures  

NLE Websites -- All DOE Office Websites (Extended Search)

Compositional Variation Within Hybrid Nanostructures Print Compositional Variation Within Hybrid Nanostructures Print The inherently high surface area of bimetallic nanoparticles makes them especially attractive materials for heterogeneous catalysis. The ability to selectively grow these and other types of nanoparticles on a desired surface is ideal for the fabrication of higher-order nanoscale architectures. However, the growth mechanism for bimetallic nanoparticles on a surface is expected to be quite different than that for free particles in solution. The altered growth process can lead to modulations in stoichiometry, elemental homogeneity, and surface structure, all of which can profoundly affect the catalytic or magnetic properties of the bimetallic nanoparticles. Now, researchers have experimentally observed these subtle structural differences through x-ray absorption spectroscopic studies at ALS Beamline 10.3.2. The results illustrate how directed nanoparticle growth on specific surfaces can lead to hybrid nanomaterials with a structurally different bimetallic component than its unhybridized counterpart.

228

Compositional Variation Within Hybrid Nanostructures  

NLE Websites -- All DOE Office Websites (Extended Search)

Compositional Variation Within Hybrid Nanostructures Print Compositional Variation Within Hybrid Nanostructures Print The inherently high surface area of bimetallic nanoparticles makes them especially attractive materials for heterogeneous catalysis. The ability to selectively grow these and other types of nanoparticles on a desired surface is ideal for the fabrication of higher-order nanoscale architectures. However, the growth mechanism for bimetallic nanoparticles on a surface is expected to be quite different than that for free particles in solution. The altered growth process can lead to modulations in stoichiometry, elemental homogeneity, and surface structure, all of which can profoundly affect the catalytic or magnetic properties of the bimetallic nanoparticles. Now, researchers have experimentally observed these subtle structural differences through x-ray absorption spectroscopic studies at ALS Beamline 10.3.2. The results illustrate how directed nanoparticle growth on specific surfaces can lead to hybrid nanomaterials with a structurally different bimetallic component than its unhybridized counterpart.

229

Compositional Variation Within Hybrid Nanostructures  

NLE Websites -- All DOE Office Websites (Extended Search)

Compositional Variation Within Hybrid Nanostructures Print Compositional Variation Within Hybrid Nanostructures Print The inherently high surface area of bimetallic nanoparticles makes them especially attractive materials for heterogeneous catalysis. The ability to selectively grow these and other types of nanoparticles on a desired surface is ideal for the fabrication of higher-order nanoscale architectures. However, the growth mechanism for bimetallic nanoparticles on a surface is expected to be quite different than that for free particles in solution. The altered growth process can lead to modulations in stoichiometry, elemental homogeneity, and surface structure, all of which can profoundly affect the catalytic or magnetic properties of the bimetallic nanoparticles. Now, researchers have experimentally observed these subtle structural differences through x-ray absorption spectroscopic studies at ALS Beamline 10.3.2. The results illustrate how directed nanoparticle growth on specific surfaces can lead to hybrid nanomaterials with a structurally different bimetallic component than its unhybridized counterpart.

230

Requirements Specifications For Hybrid Systems  

E-Print Network (OSTI)

this paper is to present a formal framework for representing and reasoning about the requirements of hybrid systems. As background, the paper briefly reviews an abstract model for specifying system and software requirements, called the Four Variable Model [12], and a related requirements method, called SCR (Software Cost Reduction) [10, 1]. The paper then introduces a special discrete version of the Four Variable Model, the SCR requirements model [8] and proposes an extension of the SCR model for specifying and reasoning about hybrid systems. 2 Background

Constance Heitmeyer

1996-01-01T23:59:59.000Z

231

Ultracapacitor Technologies and Application in Hybrid and Electric Vehicles  

E-Print Network (OSTI)

The parallel hybrid passenger car (VW Golf) combined an EDLCpassenger cars using the ultracapacitors in micro-hybrid,passenger car using both carbon/carbon and hybrid carbon

Burke, Andy

2009-01-01T23:59:59.000Z

232

Are Batteries Ready for Plug-in Hybrid Buyers?  

E-Print Network (OSTI)

and Impacts of Hybrid Electric Vehicle Options for Compactof Plug-In Hybrid Electric Vehicles, Volume 1: Nationwideand Impacts of Hybrid Electric Vehicle Options, EPRI, Palo

Axsen, Jonn; Kurani, Kenneth S; Burke, Andy

2009-01-01T23:59:59.000Z

233

Are batteries ready for plug-in hybrid buyers?  

E-Print Network (OSTI)

and Impacts of Hybrid Electric Vehicle Options for Compactof Plug-In Hybrid Electric Vehicles, Volume 1: Nationwideand Impacts of Hybrid Electric Vehicle Options, EPRI, Palo

Axsen, Jonn; Kurani, Kenneth S.; Burke, Andrew

2008-01-01T23:59:59.000Z

234

Are Batteries Ready for Plug-in Hybrid Buyers?  

E-Print Network (OSTI)

and impacts of hybrid electric vehicle options for compactof plug-in hybrid electric vehicles, vol. 1: nationwideimpacts of hybrid electric vehicle options. Report #1000349,

Axsen, Jonn; Burke, Andy; Kurani, Kenneth S

2010-01-01T23:59:59.000Z

235

Are Batteries Ready for Plug-in Hybrid Buyers?  

E-Print Network (OSTI)

M. , 2006. Plug-in hybrid vehicle analysis. Milestonegas emissions from plug-in hybrid vehicles: implications forPresentation at SAE 2008 Hybrid Vehicle Technologies

Axsen, Jonn; Burke, Andy; Kurani, Kenneth S

2010-01-01T23:59:59.000Z

236

Optimum Performance of Direct Hydrogen Hybrid Fuel Cell Vehicles  

E-Print Network (OSTI)

ultracapacitors, fuel cells and hybrid vehicle design. Dr.on electric and hybrid vehicle technology and applicationsand performance. Hybrid vehicles utilizing a load leveling

Zhao, Hengbing; Burke, Andy

2009-01-01T23:59:59.000Z

237

Advanced Vehicle Testing Activity - Medium and Heavy Duty Hybrid...  

NLE Websites -- All DOE Office Websites (Extended Search)

an electric vehicle. Medium and heavy duty HEV testing results to date are posted below. Vehicle Testing Reports INL Hybrid Shuttle Busses INL Hybrid Shuttle Busses INL Hybrid...

238

Are Batteries Ready for Plug-in Hybrid Buyers?  

E-Print Network (OSTI)

including the Hybrid and Electric Vehicle Act of 1976. Suchand Impacts of Hybrid Electric Vehicle Options for Compactof Plug-In Hybrid Electric Vehicles, Volume 1: Nationwide

Axsen, Jonn; Kurani, Kenneth S; Burke, Andy

2009-01-01T23:59:59.000Z

239

Are batteries ready for plug-in hybrid buyers?  

E-Print Network (OSTI)

including the Hybrid and Electric Vehicle Act of 1976. Suchand Impacts of Hybrid Electric Vehicle Options for Compactof Plug-In Hybrid Electric Vehicles, Volume 1: Nationwide

Axsen, Jonn; Kurani, Kenneth S.; Burke, Andrew

2008-01-01T23:59:59.000Z

240

Optimum Performance of Direct Hydrogen Hybrid Fuel Cell Vehicles  

E-Print Network (OSTI)

capacitors fuel-cell hybrid electric vehicle optimizationsize for fuel cell hybrid electric vehicle-Part I, Journalbeen developed for hybrid electric vehicles with an internal

Zhao, Hengbing; Burke, Andy

2009-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "hybrid tractor evaluation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Ultracapacitor Technologies and Application in Hybrid and Electric Vehicles  

E-Print Network (OSTI)

simulations of hybrid and electric vehicles Simulation ofand Application in Hybrid and Electric Vehicles Andrew Burkemarketing of hybrid and electric vehicles of various types

Burke, Andy

2009-01-01T23:59:59.000Z

242

Optimum Performance of Direct Hydrogen Hybrid Fuel Cell Vehicles  

E-Print Network (OSTI)

in batteries, ultracapacitors, fuel cells and hybrid vehicleBattery, Hybrid and Fuel Cell Electric Vehicle SymposiumBattery, Hybrid and Fuel Cell Electric Vehicle Symposium

Zhao, Hengbing; Burke, Andy

2009-01-01T23:59:59.000Z

243

Hybrid power technology for remote military facilities  

DOE Green Energy (OSTI)

The Department of Defense (DoD) operates hundreds of test, evaluation, and training facilities across the US and abroad. Due to the nature of their missions, these facilities are often remote and isolated from the utility grid. The preferred choice for power at these facilities has historically been manned diesel generators. The DoD Photovoltaic Review Committee, estimates that on the order of 350 million gallons of diesel fuel is burned each year to generate the 2000 GWh of electricity required to operate these remote military facilities. Other federal agencies, including the National Park Service and the USDA Forest Service use diesel generators for remote power needs as well. The generation of power diesel generators is both expensive and detrimental to the environment. The augmentation of power from diesel generators with power processing and battery energy storage enhances the efficiency and utilization of the generator resulting in lower fuel consumption and lower generator run- time in proportion to the amount of renewables added. The hybrid technology can both reduce the cost of power and reduce environmental degradation at remote DoD facilities. This paper describes the expected performance and economics of photovoltaic/diesel hybrid systems. Capabilities and status of systems now being installed at DoD facilities are presented along with financing mechanisms available within DoD.

Chapman, R.N.

1996-09-01T23:59:59.000Z

244

NYCT Diesel Hybrid-Electric Buses Program Status Update  

DOE Green Energy (OSTI)

Program status update focuses on the experiences gathered during New York City Transit's deployment of hybrid electric buses in its fleet. This report is part of an ongoing Department of Energy (DOE), Office of Heavy Vehicle Technologies program to study heavy-duty alternative fuel and advanced technology vehicles in the United States. DOE's National Renewable Energy Laboratory (NREL) is conducting the Transit Bus Evaluation Project to compare alternative fuel or advanced technology and diesel fuel buses. Information for the comparison comes from data collected on the operational, maintenance, performance, and emissions characteristics of alternative fuel or advanced technology buses currently being used in vehicle fleets and comparable diesel fuel buses serving as controls within the same fleet. This report highlights the New York City Transit (NYCT) alternative fuel and advanced technology programs including its diesel hybrid-electric buses. As part of the NREL Transit Bus Evaluation Project, data collection and evaluation of the Orion VI diesel hybrid-electric buses at NYCT are nearly complete. Final reports from the evaluation are being prepared by NREL and Battelle (NREL's support contractor for the project) and will be available in early 2002. If you want to know more about this transit bus program, its components, advanced technology vehicles, or incentive programs, contact any of the following personnel or visit the Web sites listed.

Not Available

2002-03-01T23:59:59.000Z

245

1997 hybrid electric vehicle specifications  

DOE Green Energy (OSTI)

The US DOE sponsors Advanced Vehicle Technology competitions to help educate the public and advance new vehicle technologies. For several years, DOE has provided financial and technical support for the American Tour de Sol. This event showcases electric and hybrid electric vehicles in a road rally across portions of the northeastern United States. The specifications contained in this technical memorandum apply to vehicles that will be entered in the 1997 American Tour de Sol. However, the specifications were prepared to be general enough for use by other teams and individuals interested in developing hybrid electric vehicles. The purpose of the specifications is to ensure that the vehicles developed do not present a safety hazard to the teams that build and drive them or to the judges, sponsors, or public who attend the competitions. The specifications are by no means the definitive sources of information on constructing hybrid electric vehicles - as electric and hybrid vehicles technologies advance, so will the standards and practices for their construction. In some cases, the new standards and practices will make portions of these specifications obsolete.

Sluder, S.; Larsen, R.; Duoba, M.

1996-10-01T23:59:59.000Z

246

Hybrid free electron laser devices  

Science Conference Proceedings (OSTI)

We consider hybrid free electron laser devices consisting of Cerenkov and undulator sections. We will show that they can in principle be used as segmented devices and also show the possibility of exploiting Cerenkov devices for the generation of nonlinear harmonic coherent power. We discuss both oscillator and amplifier schemes.

Asgekar, Vivek; Dattoli, G. [Department of Physics, University of Pune, Pune 411007 (India); ENEA, Unita Tecnico Scientifica Technologie Fisiche, Avanzate, Centro Ricerche Frascati, C.P. 65-00044 Frascati, Rome (Italy)

2007-03-15T23:59:59.000Z

247

Are hybrid cars too quiet?  

Science Conference Proceedings (OSTI)

The increase in availability of alternative fuel vehicles has elicited concerns for pedestrians who might not hear the approach of these quieter cars. Three experiments tested the relative audibility of hybrid vehicles (in their electric mode) and internal combustion engine (ICE) cars. Binaural recordings were made of the cars approaching from either the right or left

2009-01-01T23:59:59.000Z

248

Hybrid electrical energy storage systems  

Science Conference Proceedings (OSTI)

Electrical energy is a high quality form of energy that can be easily converted to other forms of energy with high efficiency and, even more importantly, it can be used to control lower grades of energy quality with ease. However, building a cost-effective ... Keywords: charge, electrical storage, energy, energy storage, hybrid storage, management

Massoud Pedram; Naehyuck Chang; Younghyun Kim; Yanzhi Wang

2010-08-01T23:59:59.000Z

249

How Plug-in Hybrids Save Money  

NLE Websites -- All DOE Office Websites (Extended Search)

How Plug-in Hybrids Save Money How Plug-in Hybrids Save Money Plug-in hybrid recharging Plug-in hybrids reduce fuel costs by Using high-capacity batteries that allow them to operate on electricity from the outlet for significant distances-electricity typically costs less than half as much as gasoline Using a larger electric motor that typically allows the vehicle to use electricity at higher speeds than regular hybrids Using regenerative braking to recover energy typically wasted when you apply the brakes Plug-in hybrid designs differ, and your driving habits, especially the distance you drive between re-charging, can have a big effect on your fuel bill. My Plug-in Hybrid Calculator estimates gasoline and electricity costs for any available plug-in hybrid using your driving habits and fuel costs.

250

Dynamic programming for hybrid pneumatic vehicles  

Science Conference Proceedings (OSTI)

Pneumatic hybridization of internal combustion engines may prove to be a viable and cost-efficient alternative to electric hybridization. This paper investigates the fuel consumption reduction that is possible with this rather new concept in combination ...

Christian Dönitz; Iulian Vasile; Christopher Onder; Lino Guzzella

2009-06-01T23:59:59.000Z

251

Issue 5: High Interest in Hybrid Cars  

E-Print Network (OSTI)

Survey of Oregon Hybrid Gas-Electric Car Owners. July. U.S.of a qualifying gas-electric car, but because this is aor leasing a hybrid car (gas-electric)” (Baldassare, 2004).

Ong, Paul M.; Haselhoff, Kim

2005-01-01T23:59:59.000Z

252

Hybrid vehicle-centric route guidance  

E-Print Network (OSTI)

This thesis proposes a hybrid route guidance system in which predictive guidance is generated in a centralized layer and revised in a reactive, decentralized layer that resides on-board the vehicle. This hybrid approach ...

Farver, Jennifer M. (Jennifer Margaret), 1976-

2005-01-01T23:59:59.000Z

253

Axisymmetric Magnetic Mirror Fusion-Fission Hybrid  

Science Conference Proceedings (OSTI)

Fusion-Fission Hybrids and Transmutation / Proceedings of the Fifteenth International Conference on Emerging Nuclear Energy Systems

R. W. Moir; N. N. Martovetsky; A. W. Molvik; D. D. Ryutov; T. C. Simonen

254

SYNTHESIS AND CHARACTERIZATION OF A HYBRID BIO ...  

Science Conference Proceedings (OSTI)

Synthesis and characterization of A Hybrid bio/synthetic biomimetic aggrecan Macromolecule for the treatment of Low Back Pain. ...

255

Development of Hybrid Supercapacitors for Portable Power ...  

Science Conference Proceedings (OSTI)

Examples of integrated devices built using Battelle's hybrid supercapacitor materials are presented and work ... Energy Storage for Advanced Electric Vehicles.

256

Advanced Coal Wind Hybrid: Economic Analysis  

E-Print Network (OSTI)

hybrid combined cycle power plant natural gas combined cyclePower Plants study, Volume 1: Bituminous Coal and Natural Gas

Phadke, Amol

2008-01-01T23:59:59.000Z

257

The Hybrid Automobile and the Atkinson Cycle  

Science Conference Proceedings (OSTI)

The hybrid automobile is a strikingly new automobile technology with a number of new technological features that dramatically improve energy efficiency. This paper will briefly describe how hybrid automobiles work; what are these new technological features; why the Toyota Prius hybrid internal combustion engine operates on the Atkinson cycle instead of the Otto cycle; and what are the advantages and disadvantages of the hybrid automobile. This is a follow-up to my two previous papers on the physics of automobile engines.1

Bernard J. Feldman

2008-01-01T23:59:59.000Z

258

Hybrid Controller for Multiple Energy Storage Devices ...  

Summary. A new hybrid energy storage controller developed by researchers at Pacific Northwest National Laboratory is designed for a centralized ...

259

Hybrid Organic: Inorganic Materials for Alternative Energy  

Science Conference Proceedings (OSTI)

About this Symposium. Meeting, Materials Science & Technology 2013. Symposium, Hybrid Organic: Inorganic Materials for Alternative Energy. Sponsorship.

260

Silicon bulk micromachined hybrid dimensional artifact.  

Science Conference Proceedings (OSTI)

A mesoscale dimensional artifact based on silicon bulk micromachining fabrication has been developed and manufactured with the intention of evaluating the artifact both on a high precision coordinate measuring machine (CMM) and video-probe based measuring systems. This hybrid artifact has features that can be located by both a touch probe and a video probe system with a k=2 uncertainty of 0.4 {micro}m, more than twice as good as a glass reference artifact. We also present evidence that this uncertainty could be lowered to as little as 50 nm (k=2). While video-probe based systems are commonly used to inspect mesoscale mechanical components, a video-probe system's certified accuracy is generally much worse than its repeatability. To solve this problem, an artifact has been developed which can be calibrated using a commercially available high-accuracy tactile system and then be used to calibrate typical production vision-based measurement systems. This allows for error mapping to a higher degree of accuracy than is possible with a glass reference artifact. Details of the designed features and manufacturing process of the hybrid dimensional artifact are given and a comparison of the designed features to the measured features of the manufactured artifact is presented and discussed. Measurement results from vision and touch probe systems are compared and evaluated to determine the capability of the manufactured artifact to serve as a calibration tool for video-probe systems. An uncertainty analysis for calibration of the artifact using a CMM is presented.

Claudet, Andre A.; Tran, Hy D.; Bauer, Todd Marks; Shilling, Katherine Meghan; Oliver, Andrew David

2010-03-01T23:59:59.000Z

Note: This page contains sample records for the topic "hybrid tractor evaluation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Advanced Coal Wind Hybrid: Economic Analysis  

E-Print Network (OSTI)

LBNL-1248E Advanced Coal Wind Hybrid: Economic Analysis Principal Authors Amol Phadke1 , Charles;Advanced Coal Wind Hybrid: Economic Analysis ii LBNL-1248E Advanced Coal Wind Hybrid: Economic Analysis and Analysis of the U.S. Department of Energy (DOE) under Contract No. DE-AC02-05CH11231. #12;#12;Advanced Coal

262

In-Use Performance Comparison of Hybrid Electric, CNG, and Diesel Buses at New York City Transit  

Science Conference Proceedings (OSTI)

The National Renewable Energy Laboratory (NREL) evaluated the performance of diesel, compressed natural gas (CNG), and hybrid electric (equipped with BAE Systems? HybriDrive propulsion system) transit buses at New York City Transit (NYCT). CNG, Gen I and Gen II hybrid electric propulsion systems were compared on fuel economy, maintenance and operating costs per mile, and reliability.

Barnitt, R. A.

2008-06-01T23:59:59.000Z

263

Feasibility study of a hybrid erosion drilling concept  

DOE Green Energy (OSTI)

The results of a system analysis of the ERODRILL concept are presented. ERODRILL is an erosion drilling technique that uses a stream of propellant capsules carried in the drilling mud and ignited near the bottom of the drill hole to provide a fluid jet on the rock face. The concept evaluated in this study was a hybrid system using the erosion drill to cut a kerf for a conventional rotary drill to break to. A preliminary design was made and a hypergolic propellant, Hercules HES 6573, was chosen. The background and rationale for this program are presented. The system, from its initial conception to its current hybrid design, is described. The propellant selection process is presented. The hazard evaluation, reliability analysis, and the economic analysis are given. Conclusions and recommendations are included. (MHR)

Not Available

1977-06-01T23:59:59.000Z

264

Alternative Fuels Data Center: Heavy-Duty Vehicle and Engine...  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Kenworth - T270 hybrid Kenworth - T370 diesel electric tractor Peterbilt Motors - 337338 Peterbilt Motors - 330 Hybrid Paccar - PX-6 6.7L Fuel Type: Hybrid - Diesel Hydraulic...

265

Alternative Fuels Data Center: Heavy-Duty Vehicle and Engine...  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Peterbilt Motors - 386HE Kenworth - T370 hybrid truck Kenworth - T270 hybrid IC Bus - HC Hybrid Series Turtle Top - Odyssey XLT Kenworth - T370 diesel electric tractor Thomas Built...

266

Hybrid refrigeration/sorption solar-cooling systems  

DOE Green Energy (OSTI)

The hybrid refrigeration/sorption concept is a technically feasible approach to solar cooling which has not yet been systematically evaluated. Various system configurations are possible, each with advantages and disadvantages relative to the others, and with respect to solar cooling systems based on the individual absorption, Rankine, and desiccant technologies. Conventional cooling and dehumidification, sorption dehumidification, and the effects on the refrigeration unit of adding a dehumidifier are discussed.

Curran, H.M.

1981-08-01T23:59:59.000Z

267

Fusion-Fission Hybrid for Fissile Fuel Production without Processing  

SciTech Connect

Two scenarios are typically envisioned for thorium fuel cycles: 'open' cycles based on irradiation of {sup 232}Th and fission of {sup 233}U in situ without reprocessing or 'closed' cycles based on irradiation of {sup 232}Th followed by reprocessing, and recycling of {sup 233}U either in situ or in critical fission reactors. This study evaluates a third option based on the possibility of breeding fissile material in a fusion-fission hybrid reactor and burning the same fuel in a critical reactor without any reprocessing or reconditioning. This fuel cycle requires the hybrid and the critical reactor to use the same fuel form. TRISO particles embedded in carbon pebbles were selected as the preferred form of fuel and an inertial laser fusion system featuring a subcritical blanket was combined with critical pebble bed reactors, either gas-cooled or liquid-salt-cooled. The hybrid reactor was modeled based on the earlier, hybrid version of the LLNL Laser Inertial Fusion Energy (LIFE1) system, whereas the critical reactors were modeled according to the Pebble Bed Modular Reactor (PBMR) and the Pebble Bed Advanced High Temperature Reactor (PB-AHTR) design. An extensive neutronic analysis was carried out for both the hybrid and the fission reactors in order to track the fuel composition at each stage of the fuel cycle and ultimately determine the plant support ratio, which has been defined as the ratio between the thermal power generated in fission reactors and the fusion power required to breed the fissile fuel burnt in these fission reactors. It was found that the maximum attainable plant support ratio for a thorium fuel cycle that employs neither enrichment nor reprocessing is about 2. This requires tuning the neutron energy towards high energy for breeding and towards thermal energy for burning. A high fuel loading in the pebbles allows a faster spectrum in the hybrid blanket; mixing dummy carbon pebbles with fuel pebbles enables a softer spectrum in the critical reactors. This combination consumes about 20% of the thorium initially loaded in the hybrid reactor ({approx}200 GWd/tHM), partially during hybrid operation, but mostly during operation in the critical reactor. The plant support ratio is low compared to the one attainable using continuous fuel chemical reprocessing, which can yield a plant support ratio of about 20, but the resulting fuel cycle offers better proliferation resistance as fissile material is never separated from the other fuel components.

Fratoni, M; Moir, R W; Kramer, K J; Latkowski, J F; Meier, W R; Powers, J J

2012-01-02T23:59:59.000Z

268

Hybrid Electric Vehicle Basics | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Hybrid Electric Vehicle Basics Hybrid Electric Vehicle Basics Hybrid Electric Vehicle Basics August 20, 2013 - 9:13am Addthis Photo of hands holding a battery pack (grey rectangular box) for a hybrid electric vehicle. Hybrid electric vehicles (HEVs) combine the benefits of high fuel economy and low emissions with the power, range, and convenience of conventional diesel and gasoline fueling. HEV technologies also have potential to be combined with alternative fuels and fuel cells to provide additional benefits. Future offerings might also include plug-in hybrid electric vehicles. Hybrid electric vehicles typically combine the internal combustion engine of a conventional vehicle with the battery and electric motor of an electric vehicle. The combination offers low emissions and convenience-HEVs never need to be plugged in.

269

Hybrid Electric Vehicle Basics | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Hybrid Electric Vehicle Basics Hybrid Electric Vehicle Basics Hybrid Electric Vehicle Basics August 20, 2013 - 9:13am Addthis Photo of hands holding a battery pack (grey rectangular box) for a hybrid electric vehicle. Hybrid electric vehicles (HEVs) combine the benefits of high fuel economy and low emissions with the power, range, and convenience of conventional diesel and gasoline fueling. HEV technologies also have potential to be combined with alternative fuels and fuel cells to provide additional benefits. Future offerings might also include plug-in hybrid electric vehicles. Hybrid electric vehicles typically combine the internal combustion engine of a conventional vehicle with the battery and electric motor of an electric vehicle. The combination offers low emissions and convenience-HEVs never need to be plugged in.

270

Planar slot coupled microwave hybrid  

DOE Patents (OSTI)

A symmetrical 180.degree. microwave hybrid is constructed by opening a slot line in a ground plane below a conducting strip disposed on a dielectric substrate, creating a slot coupled conductor. Difference signals propagating on the slot coupled conductor are isolated on the slot line leaving sum signals to propagate on the microstrip. The difference signal is coupled from the slot line onto a second microstrip line for transmission to a desired location. The microstrip branches in a symmetrical fashion to provide the input/output ports of the 180.degree. hybrid. The symmetry of the device provides for balance and isolation between sum and difference signals, and provides an advantageous balance between the power handling capabilities and the bandwidth of the device.

Petter, Jeffrey K. (Williston, VT)

1991-01-01T23:59:59.000Z

271

Optimum flywheel sizing for parallel and series hybrid vehicles  

DOE Green Energy (OSTI)

Flywheels have the possibility of providing high turnaround efficiency and high specific power output. These characteristics are very important for the successful manufacture of parallel and series hybrid vehicles, which have the potential for providing high fuel economy and very low emissions with range and performance comparable to today`s light-duty vehicles. Flywheels have a high specific power output, but relatively low specific energy output. Therefore, it is of importance to determine energy and power requirements for flywheels applied to light-duty vehicles. Vehicle applications that require an energy storage system with high power and low energy are likely to benefit from a flywheel. In this paper, a vehicle simulation code and a flywheel model are applied to the calculation of optimum flywheel energy storage capacity for a parallel and a series hybrid vehicle. A conventional vehicle is also evaluated as a base-case, to provide an indication of the fuel economy gains that can be obtained with flywheel hybrid vehicles. The results of the analysis indicate that the optimum flywheel energy storage capacity is relatively small. This results in a low weight unit that has a significant power output and high efficiency. Emissions generated by the hybrid vehicles are not calculated, but have the potential of being significantly lower than the emissions from the conventional car.

Aceves, S.M.; Smith, J.R.

1996-12-20T23:59:59.000Z

272

Compositional Variation Within Hybrid Nanostructures  

NLE Websites -- All DOE Office Websites (Extended Search)

Compositional Variation Within Compositional Variation Within Hybrid Nanostructures Compositional Variation Within Hybrid Nanostructures Print Wednesday, 29 September 2010 00:00 The inherently high surface area of bimetallic nanoparticles makes them especially attractive materials for heterogeneous catalysis. The ability to selectively grow these and other types of nanoparticles on a desired surface is ideal for the fabrication of higher-order nanoscale architectures. However, the growth mechanism for bimetallic nanoparticles on a surface is expected to be quite different than that for free particles in solution. The altered growth process can lead to modulations in stoichiometry, elemental homogeneity, and surface structure, all of which can profoundly affect the catalytic or magnetic properties of the bimetallic nanoparticles. Now, researchers have experimentally observed these subtle structural differences through x-ray absorption spectroscopic studies at ALS Beamline 10.3.2. The results illustrate how directed nanoparticle growth on specific surfaces can lead to hybrid nanomaterials with a structurally different bimetallic component than its unhybridized counterpart.

273

Hybrid Kansei-SOM model using risk management and company assessment for stock trading  

Science Conference Proceedings (OSTI)

Risk management and stock assessment are key methods for stock trading decisions. In this paper, we present a new stock trading method using Kansei evaluation integrated with a Self-Organizing Map model for improvement of a stock trading system. The ... Keywords: Hybrid intelligent trading system, Investment risk, Kansei evaluation, Risk management, Self-Organizing Map, Stock trading system

Hai V. Pham, Eric W. Cooper, Thang Cao, Katsuari Kamei

2014-01-01T23:59:59.000Z

274

NREL: Learning - Fuel Cell, Hybrid Electric, and Plug-In Hybrid...  

NLE Websites -- All DOE Office Websites (Extended Search)

Cell, Hybrid Electric, and Plug-In Hybrid Vehicles Photo of a small blue subcompact vehicle in a roadway with other vehicles and foothills in the background. Experimental fuel...

275

Solid Oxide Fuel Cell Hybrid System for Distributed Power Generation  

DOE Green Energy (OSTI)

This report summarizes the work performed by Hybrid Power Generation Systems, LLC (HPGS) under Cooperative Agreement DE-FC2601NT40779 for the US Department of Energy, National Energy Technology Laboratory (DoE/NETL) entitled ''Solid Oxide Fuel Cell Hybrid System for Distributed Power Generation''. The main objective of this project is to develop and demonstrate the feasibility of a highly efficient hybrid system integrating a planar Solid Oxide Fuel Cell (SOFC) and a gas turbine. A conceptual hybrid system design was selected for analysis and evaluation. The selected system is estimated to have over 65% system efficiency, a first cost of approximately $650/kW, and a cost of electricity of 8.4 cents/kW-hr. A control strategy and conceptual control design have been developed for the system. A number of SOFC module tests have been completed to evaluate the pressure impact to performance stability. The results show that the operating pressure accelerates the performance degradation. Several experiments were conducted to explore the effects of pressure on carbon formation. Experimental observations on a functioning cell have verified that carbon deposition does not occur in the cell at steam-to-carbon ratios lower than the steady-state design point for hybrid systems. Heat exchanger design, fabrication and performance testing as well as oxidation testing to support heat exchanger life analysis were also conducted. Performance tests of the prototype heat exchanger yielded heat transfer and pressure drop characteristics consistent with the heat exchanger specification. Multicell stacks have been tested and performance maps were obtained under hybrid operating conditions. Successful and repeatable fabrication of large (>12-inch diameter) planar SOFC cells was demonstrated using the tape calendering process. A number of large area cells and stacks were successfully performance tested at ambient and pressurized conditions. A 25 MW plant configuration was selected with projected system efficiency of over 65% and a factory cost of under $400/kW. The plant design is modular and can be scaled to both higher and lower plant power ratings. Integrated gasification fuel cell systems or IGFCs were developed and analyzed for plant sizes in excess of 200 MW. Two alternative integration configurations were selected with projected system efficiency of over 53% on a HHV basis, or about 10 percentage points higher than that of the state-of-the-art Integrated Gasification Combined Cycle (IGCC) systems.

Nguyen Minh

2005-12-01T23:59:59.000Z

276

Hybrid powertrain controller - Energy Innovation Portal  

A hybrid powertrain for a vehicle comprising a diesel engine and an electric motor in a parallel arrangement with a multiple ratio transmission located on the torque ...

277

Ultracapacitors and Batteries in Hybrid Vehicles  

DOE Green Energy (OSTI)

Using an ultracapacitor in conjunction with a battery in a hybrid vehicle combines the power performance of the former with the greater energy storage capability of the latter.

Pesaran, A.; Markel, T.; Zolot, M.; Sprik, S.

2005-08-01T23:59:59.000Z

278

How Plug-in Hybrids Save Money  

NLE Websites -- All DOE Office Websites (Extended Search)

of gasoline's widespread availability and quick refueling. Plug-in hybrids also save energy through regenerative braking, which recovers much of the energy typically lost when...

279

Plug-In Hybrid Electric Vehicles (Presentation)  

DOE Green Energy (OSTI)

Provides an overview on the current status, long-term prospects, and key challenges in the development of plug-in hybrid electric vehicle technology.

Markel, T.

2006-05-08T23:59:59.000Z

280

Hybrid Anode for Semiconductor Radiation Detectors - Energy ...  

The present invention relates to a novel hybrid anode configuration for a radiation detector that effectively reduces the edge effect of surface defects on the ...

Note: This page contains sample records for the topic "hybrid tractor evaluation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Advanced Vehicle Testing Activity - Hybrid Electric Vehicles  

NLE Websites -- All DOE Office Websites (Extended Search)

Hyundai Sonata (4932) Battery Report 2010 Ultra-Battery Honda Civic Battery Report Some hybrid electric vehicles (HEVs) combine a conventional internal combustion engine (using...

282

Hybrid Electric and Pure Electric vehicle testing  

NLE Websites -- All DOE Office Websites (Extended Search)

Hybrid Electric and Pure Electric Vehicle Testing (Advanced Vehicle Testing Activity) Jim Francfort Discovery Center of Idaho - September 2005 INLCON-05-00693 HEV & EV Testing...

283

A verification framework for hybrid systems  

E-Print Network (OSTI)

Combining; discrete state transitions with differential equations, Hybrid system models provide an expressive formalism for describing software systems that interact with a physical environment. Automatically checking ...

Mitra, Sayan

2007-01-01T23:59:59.000Z

284

Advanced Coal Wind Hybrid: Economic Analysis  

E-Print Network (OSTI)

IGCC PC advanced coal-wind hybrid combined cycle power plantnatural gas combined cycle gas turbine power plant carboncrude gasification combined cycle power plant with carbon

Phadke, Amol

2008-01-01T23:59:59.000Z

285

Advanced Vehicle Testing Activity: Hybrid Electric Vehicles  

NLE Websites -- All DOE Office Websites (Extended Search)

motor of an electric vehicle. Other hybrids combine a fuel cell with batteries to power electric propulsion motors. Fuel Cell Concept: Fuel passes through an anode, electrolyte,...

286

Plug-In Hybrid Electric Vehicles - Assessment  

NLE Websites -- All DOE Office Websites (Extended Search)

EPRI and Argonne Assess Commercial Viability of Plug-In Hybrid Electric Vehicles The Electric Power Research Institute (EPRI) and Argonne National Laboratory are engaged in a...

287

Hybrid Performance of the Pierre Auger Observatory  

E-Print Network (OSTI)

A key feature of the Pierre Auger Observatory is its hybrid design, in which ultra high energy cosmic rays are detected simultaneously by fluorescence telescopes and a ground array. The two techniques see air showers in complementary ways, providing important cross-checks and measurement redundancy. Much of the hybrid capability stems from the accurate geometrical reconstruction it achieves, with accuracy better than either the ground array detectors or a single telescope could achieve independently. We have studied the geometrical and longitudinal profile reconstructions of hybrid events. We present the results for the hybrid performance of the Observatory, including trigger efficiency, energy and angular resolution, and the efficiency of the event selection.

B. R. Dawson; for the Pierre Auger Collaboration

2007-06-08T23:59:59.000Z

288

Hybrid Rotaxanes: Interlocked Structures for Quantum Computing...  

NLE Websites -- All DOE Office Websites (Extended Search)

Hybrid Rotaxanes: Interlocked Structures for Quantum Computing? Print Rotaxanes are mechanically interlocked molecular architectures consisting of a dumbbell-shaped molecule, the...

289

Test and Evaluation of a Hybrid Desiccant Dehumidifier  

Science Conference Proceedings (OSTI)

Dehumidification technology is being investigated for potential savings in building air conditioning systems. The potential for savings lies in separating the sensible and the latent cooling loads to more efficiently address the combined conditioning needs of the space. The Munters DryCool HD combined desiccant/vapor compression system was tested in the EPRI Knoxville psychrometric chambers. The system was tested in the laboratory for a host of indoor and outdoor conditions. The system provides cooling a...

2011-05-09T23:59:59.000Z

290

King County Metro Transit Hybrid Articulated Buses: Interim Evaluation...  

NLE Websites -- All DOE Office Websites (Extended Search)

CA Peterbilt378, Class 8 truck Cummins Westport ISXG high-pressure direct injection LNG and diesel Completed in 2004 Note: CNG compressed natural gas; LNG liquefied...

291

King County Metro Transit Hybrid Articulated Buses: Final Evaluation...  

NLE Websites -- All DOE Office Websites (Extended Search)

CA Peterbilt378, Class 8 truck Cummins Westport ISXG high-pressure direct injection LNG and diesel Completed in 2004 Note: CNG compressed natural gas; LNG liquefied...

292

Twelve-Month Evaluation of UPS Diesel Hybrid Electric Delivery...  

NLE Websites -- All DOE Office Websites (Extended Search)

truck Cummins Westport ISXG high- pressure, direct- injection, lique- fied natural gas (LNG) and diesel Completed in 2004 2 Project Design and Data Collection This report...

293

Evaluation Of Potential Hybrid Electric Vehicle Applications: Vol I  

E-Print Network (OSTI)

note is that the energy per mile at 0% regenerative brakingfor energy consumption reductions due to regenerativeand energy per mile needed are listed in Table 9 for different regenerative

Gris, Arturo E.

1991-01-01T23:59:59.000Z

294

Evaluation Of Potential Hybrid Electric Vehicle Applications: Vol I  

E-Print Network (OSTI)

Air Batteries for Electric Vehicles” E.J.Rudd. SAE 891660.the Soleq Evcort Electric Vehicle”. DOE/ID--10232. Preparedfor Fiscal Year 88, Electric Vehicle Program, February

Gris, Arturo E.

1991-01-01T23:59:59.000Z

295

Hybrid Vehicle design and evaluation Andrew Burke and Hengbing Zhao  

E-Print Network (OSTI)

-mode (Toyota/Prius) c. Multiple-planetary,dual-mode (GM) d. Multiple-shaft, dual-clutch transmission (VW effi ciency data from simulations for 2004 Prius and 2006 Civic HEV Drive Cycle NEDC FUDS HWFE T US06 Si m 3.2 (74) 3.5 (68) 3.6 (66) 5.5 (43)2004 Prius HEV EP A 3.6 (67) a 3.6 (65) c Si m 4.1 (58) 4

California at Davis, University of

296

Design and Evaluation of Hybrid Fault-Detection Systems  

Science Conference Proceedings (OSTI)

As chip densities and clock rates increase, processors are becoming more susceptible to transient faults that can affect program correctness. Up to now, system designers have primarily considered hardware-only and software-only fault-detection mechanisms ...

George A. Reis; Jonathan Chang; Neil Vachharajani; Ram Rangan; David I. August; Shubhendu S. Mukherjee

2005-06-01T23:59:59.000Z

297

Hybrid eager and lazy evaluation for efficient compilation of Haskell  

E-Print Network (OSTI)

The advantage of a non-strict, purely functional language such as Haskell lies in its clean equational semantics. However, lazy implementations of Haskell fall short: they cannot express tail recursion gracefully without ...

Maessen, Jan-Willem

2002-01-01T23:59:59.000Z

298

Cooling Evolution of Hybrid Stars  

E-Print Network (OSTI)

The cooling of compact isolated objects for different values of the gravitational mass has been simulated for two alternative assumptions. One is that the interior of the star is purely hadronic and second that the star can have a rather large quark core. It has been shown that within a nonlocal chiral quark model the critical density for a phase transition to color superconducting quark matter under neutron star conditions can be low enough for these phases to occur in compact star configurations with masses below 1.3 M_sun. For a realistic choice of parameters the equation of state (EoS) allows for 2SC quark matter with a large quark gap ~ 100 MeV for u and d quarks of two colors that coexists with normal quark matter within a mixed phase in the hybrid star interior. We argue that, if in the hadronic phase the neutron pairing gap in 3P_2 channel is larger than few keV and the phases with unpaired quarks are allowed, the corresponding hybrid stars would cool too fast. Even in the case of the essentially supp...

Grigorian, H

2005-01-01T23:59:59.000Z

299

Hybrid regional air pollution models  

SciTech Connect

This discussion deals with a family of air quality models for predicting and analyzing the fine particulate loading in the atmosphere, for assessing the extent and degree of visibility impairment, and for determining the potential of pollutants for increasing the acidity of soils and water. The major horizontal scales of interest are from 400km to 2000km; and the time scales may vary from several hours, to days, weeks, and a few months or years, depending on the EPA regulations being addressed. First the role air quality models play in the general family of atmospheric simulation models is described. Then, the characteristics of a well-designed, comprehensive air quality model are discussed. Following this, the specific objectives of this workshop are outlined, and their modeling implications are summarized. There are significant modeling differences produced by the choice of the coordinate system, whether it be the fixed Eulerian system, the moving Lagrangian system, or some hybrid of the two. These three systems are briefly discussed, and a list of hybrid models that are currently in use are given. Finally, the PNL regional transport model is outlined and a number of research needs are listed.

Drake, R.L.

1980-03-01T23:59:59.000Z

300

Drive cycle analysis of the performance of hybrid electric vehicles  

Science Conference Proceedings (OSTI)

This paper presents a drive cycle analysis of hybrid electric vehicle power train configurations. Based on fuel economy and emissions factors, a tradeoff between conventional, series hybrid, parallel hybrid, and a parallel-series hybrid is drawn. The ... Keywords: emissions, fuel consumption, hybrid electric vehicles, modeling and simulation

Behnam Ganji; Abbas Z. Kouzani; H. M. Trinh

2010-09-01T23:59:59.000Z

Note: This page contains sample records for the topic "hybrid tractor evaluation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

The LatestThe LatestThe LatestThe Latest,,,, Quick Motor EvaluationQuick Motor EvaluationQuick Motor EvaluationQuick Motor Evaluation Myway Plus Development of Specialized Equipment  

E-Print Network (OSTI)

The LatestThe LatestThe LatestThe Latest,,,, Quick Motor EvaluationQuick Motor EvaluationQuick Motor EvaluationQuick Motor Evaluation Myway Plus Development of Specialized Equipment Myway Plus developed a quick test/evaluation equipment for highly efficient hybrid car (HV) motor. The equipment

Kambhampati, Patanjali

302

Electrochemical Capacitors as Energy Storage in Hybrid-Electric Vehicles: Present Status and Future Prospects  

E-Print Network (OSTI)

Energy Storage in Hybrid- Electric Vehicles: Present Statusmarketing of hybrid-electric vehicles of various types arefor various types of hybrid-electric vehicles Type of hybrid

Burke, Andy; Miller, Marshall

2009-01-01T23:59:59.000Z

303

Interim Project Results: United Parcel Service's Second-Generation Hybrid-Electric Delivery Vans (Fact Sheet)  

DOE Green Energy (OSTI)

This fact sheet describes the performance evaluation of United Parcel Service's second-generation hybrid-electric delivery vans. The Fleet Test and Evaluation Team at the National Renewable Energy Laboratory (NREL) is evaluating the 18-month, in-service performance of 11 of these vans along with 11 comparable conventional diesel vans operating in Minneapolis, Minnesota. As a complement to the field study, the team recently completed fuel economy and emissions testing at NREL's Renewable Fuels and Lubricants (ReFUEL) laboratory.

Not Available

2012-01-01T23:59:59.000Z

304

The Architecture of Phenotypes in a Naturally Hybridizing Complex of Xiphophorus Fishes  

E-Print Network (OSTI)

The origin and maintenance of phenotypic variation has generated considerable interest among students of functional morphology, sexual selection and behavioral ecology. In particular, hybridization has been suggested as a phenomenon which may generate novel phenotypic variation. In this dissertation I focus on the Xiphophorus birchmanni - X. malinche hybrid system to assess the role of hybridization in altering behavioral, morphological, sexual and non-sexual traits. I determine the relationship between the sword sexual ornament and body condition to support previous work which suggests that the sword is an inexpensive means to increase apparent size. My findings support the prediction that, while body size is condition-dependent, the sword is not. I show a trend toward hybrid populations displaying increased phenotypic variance and reduced phenotypic integration in sexual ornaments and body size. These findings provide evidence for a potential answer to a central question in the study of sexual selection, that of reduced genetic and phenotypic variance in sexual ornaments as the result of persistent direction selection generated by female choice. I take advantage of reduced phenotypic integration in hybrids allowing the evaluation of locomotor performance across a broad range of multivariate trait values. Sexual ornaments did not impair swimming performance per se. Rather, the sword negatively affected performance only when paired with a sub-optimal body shape. I evaluated how natural hybridization changes the relationship between boldness and anti-predator response. In poeciliid fishes, bold individuals have increased survival in the presence of predators. This non-intuitive observation may result from bold individuals being more likely to engage in anti-predator behaviors. Counter to my prediction, bold individuals were less likely to perform a fast-start response to a predator threat. This correlation was consistent among populations and species but was only significant in hybrids. My findings suggest that hybridization could influence correlations between behavioral traits in a manner similar to that documented for morphological traits.

Johnson, James Bradley

2013-05-01T23:59:59.000Z

305

Thermal Modeling of Hybrid Storage Clusters  

Science Conference Proceedings (OSTI)

There is a lack of thermal models for storage clusters; most existing thermal models do not take into account the utilization of hard drives (HDDs) and solid state disks (SSDs). To address this problem, we build a thermal model for hybrid storage clusters ... Keywords: Cluster, Hybrid, Model, Storage, Thermal

Xunfei Jiang; Maen M. Al Assaf; Ji Zhang; Mohammed I. Alghamdi; Xiaojun Ruan; Tausif Muzaffar; Xiao Qin

2013-09-01T23:59:59.000Z

306

A universal planning system for hybrid domains  

Science Conference Proceedings (OSTI)

Many real world problems involve hybrid systems, subject to (continuous) physical effects and controlled by (discrete) digital equipments. Indeed, many efforts are being made to extend the current planning systems and modelling languages to support such ... Keywords: Hybrid systems, PDDL+, Universal planning

Giuseppe Della Penna; Daniele Magazzeni; Fabio Mercorio

2012-06-01T23:59:59.000Z

307

Presented by Adaptive Hybrid Mesh Refinement for  

E-Print Network (OSTI)

meters. · Orography plays an important role in determining the strength and location of the atmospheric on orographic field data Hybrid adapted geodesic mesh based on orographic field data Structured adapted spherical mesh based on orographic field data #12;7 Khamayseh_ITAPS_SC07 h-Adaptive hybrid mesh generation

308

Solving Fuzzy Linear Regression with Hybrid Optimization  

Science Conference Proceedings (OSTI)

Fuzzy linear regression is an important tool to find the linear inexact relationship between uncertain data. We then propose a hybrid optimization method based on tabu search and harmony search as a potential way of solving fuzzy linear regression. The ... Keywords: Fuzzy linear regression, Harmony search, Hybrid optimization, Tabu search

M. H. Mashinchi; M. A. Orgun; M. Mashinchi

2009-12-01T23:59:59.000Z

309

A hybrid face recognition approach using GPUMLib  

Science Conference Proceedings (OSTI)

We present a hybrid face recognition approach which relies on a Graphics Processing Unit (GPU) Machine Learning (ML) Library (GPUMLib). The library includes a high-performance implementation of the Non-Negative Matrix Factorization (NMF) and the Multiple ... Keywords: GPU computing, face recognition, hybrid systems, multiple back-propagation, non-negative matrix factorization

Noel Lopes; Bernardete Ribeiro

2010-11-01T23:59:59.000Z

310

Brief Equivalence of hybrid dynamical models  

Science Conference Proceedings (OSTI)

This paper establishes equivalences among five classes of hybrid systems: mixed logical dynamical (MLD) systems, linear complementarity (LC) systems, extended linear complementarity (ELC) systems, piecewise affine (PWA) systems, and max-min-plus-scaling ... Keywords: Equivalent models, Hybrid systems, Piecewise affine systems

W. P. M. H. Heemels; B. De Schutter; A. Bemporad

2001-07-01T23:59:59.000Z

311

Poulsen Hybrid, LLC | Open Energy Information  

Open Energy Info (EERE)

Poulsen Hybrid, LLC Poulsen Hybrid, LLC Jump to: navigation, search Name Poulsen Hybrid, LLC Address 6 Waterview Drive Place Shelton, Connecticut Zip 06615 Sector Vehicles Product Poulsen Hybrid Year founded 2007 Number of employees 1-10 Phone number 203-954-0050 Website http://www.poulsenhybrid.com Coordinates 41.2940567°, -73.0830626° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":41.2940567,"lon":-73.0830626,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

312

Hybrid Multicore Consortium Tackles Programming Challenges  

NLE Websites -- All DOE Office Websites (Extended Search)

Hybrid Multicore Hybrid Multicore Consortium Tackles Programming Challenges Hybrid Multicore Consortium Tackles Programming Challenges Oak Ridge, Lawrence Berkeley and Los Alamos national laboratories to pool high-end computing expertise with Georgia Tech, Swiss University November 18, 2009 HMC PORTLAND, Oregon-While hybrid multicore technologies will be a critical component in future high-end computing systems, most of today's scientific applications will require a significant re-engineering effort to take advantage of the resources provided by these systems. To address this challenge, three U.S. Department of Energy national laboratories, including the Berkeley Lab, and two leading universities have formed the Hybrid Multicore Consortium, or HMC, and held their first meeting at SC09.

313

Ultra-thin microporous/hybrid materials  

DOE Patents (OSTI)

Ultra-thin hybrid and/or microporous materials and methods for their fabrication are provided. In one embodiment, the exemplary hybrid membranes can be formed including successive surface activation and reaction steps on a porous support that is patterned or non-patterned. The surface activation can be performed using remote plasma exposure to locally activate the exterior surfaces of porous support. Organic/inorganic hybrid precursors such as organometallic silane precursors can be condensed on the locally activated exterior surfaces, whereby ALD reactions can then take place between the condensed hybrid precursors and a reactant. Various embodiments can also include an intermittent replacement of ALD precursors during the membrane formation so as to enhance the hybrid molecular network of the membranes.

Jiang, Ying-Bing (Albuquerque, NM); Cecchi, Joseph L. (Albuquerque, NM); Brinker, C. Jeffrey (Albuquerque, NM)

2012-05-29T23:59:59.000Z

314

Effects of Vehicle Image in Gasoline-Hybrid Electric Vehicles  

E-Print Network (OSTI)

Survey of Oregon Hybrid Gas-Electric Car Owners. Julysimilar disdain for non-hybrid compact cars. During her HEVefficient, non-hybrid compact or midsized car during their

Heffner, Reid R.; Kurani, Ken; Turrentine, Tom

2005-01-01T23:59:59.000Z

315

Effects of Vehicle Image in Gasoline-Hybrid Electric Vehicles  

E-Print Network (OSTI)

similar disdain for non-hybrid compact cars. During her HEVSurvey of Oregon Hybrid Gas-Electric Car Owners. Julyefficient, non-hybrid compact or midsized car during their

Heffner, Reid R.; Kurani, Kenneth S; Turrentine, Tom

2005-01-01T23:59:59.000Z

316

Are batteries ready for plug-in hybrid buyers?  

E-Print Network (OSTI)

M. (2006) Plug-In Hybrid Vehicle Analysis, Milestone Report,gas emissions from plug-in hybrid vehicles: Implications forPresentation at SAE 2008 Hybrid Vehicle Technologies

Axsen, Jonn; Kurani, Kenneth S.; Burke, Andrew

2008-01-01T23:59:59.000Z

317

Are Batteries Ready for Plug-in Hybrid Buyers?  

E-Print Network (OSTI)

M. (2006) Plug-In Hybrid Vehicle Analysis, Milestone Report,gas emissions from plug-in hybrid vehicles: Implications forPresentation at SAE 2008 Hybrid Vehicle Technologies

Axsen, Jonn; Kurani, Kenneth S; Burke, Andy

2009-01-01T23:59:59.000Z

318

Ultracapacitor Technologies and Application in Hybrid and Electric Vehicles  

E-Print Network (OSTI)

Power Battery for Hybrid Vehicle Applications. ProceedingsAF. Electric and Hybrid Vehicle Design and Performance.A, Thornton M. Plug-in Hybrid Vehicle Analysis. NREL/MP-540-

Burke, Andy

2009-01-01T23:59:59.000Z

319

Charge It: The Promise of Plug-in Electric Hybrids  

E-Print Network (OSTI)

Impacts of Plug-In Hybrid Electric Vehicles on Energy andthe plug-in hybrid electric vehicle, a variant of theknown self-charging hybrid electric vehicle, is fast gaining

Recker, W.W.; Kang, J.E.

2011-01-01T23:59:59.000Z

320

Charge It: The Promise of Plug-in Electric Hybrids  

E-Print Network (OSTI)

Impacts of Plug-In Hybrid Electric Vehicles on Energy andthe plug-in hybrid electric vehicle, a variant of theknown self-charging hybrid electric vehicle, is fast gaining

Recker, W. W.; Kang, J. E.

2010-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "hybrid tractor evaluation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Are Batteries Ready for Plug-in Hybrid Buyers?  

E-Print Network (OSTI)

including the Hybrid and Electric Vehicle Act of 1976. Suchfor plug- in hybrid electric vehicles: analysis and2007. Plug-in Hybrid Electric Vehicle R&D Plan: Working

Axsen, Jonn; Burke, Andy; Kurani, Kenneth S

2010-01-01T23:59:59.000Z

322

Effects of Vehicle Image in Gasoline-Hybrid Electric Vehicles  

E-Print Network (OSTI)

Image in Gasoline-Hybrid Electric Vehicles Reid R. HeffnerImage in Gasoline-Hybrid Electric Vehicles Reid R. Heffner,6, 2005 Abstract Hybrid electric vehicles (HEVs) have image,

Heffner, Reid R.; Kurani, Ken; Turrentine, Tom

2005-01-01T23:59:59.000Z

323

Effects of Vehicle Image in Gasoline-Hybrid Electric Vehicles  

E-Print Network (OSTI)

6, 2005 Abstract Hybrid electric vehicles (HEVs) have image,Image in Gasoline-Hybrid Electric Vehicles Reid R. HeffnerImage in Gasoline-Hybrid Electric Vehicles Reid R. Heffner,

Heffner, Reid R.; Kurani, Kenneth S; Turrentine, Tom

2005-01-01T23:59:59.000Z

324

Hybrid2: The hybrid system simulation model, Version 1.0, user manual  

DOE Green Energy (OSTI)

In light of the large scale desire for energy in remote communities, especially in the developing world, the need for a detailed long term performance prediction model for hybrid power systems was seen. To meet these ends, engineers from the National Renewable Energy Laboratory (NREL) and the University of Massachusetts (UMass) have spent the last three years developing the Hybrid2 software. The Hybrid2 code provides a means to conduct long term, detailed simulations of the performance of a large array of hybrid power systems. This work acts as an introduction and users manual to the Hybrid2 software. The manual describes the Hybrid2 code, what is included with the software and instructs the user on the structure of the code. The manual also describes some of the major features of the Hybrid2 code as well as how to create projects and run hybrid system simulations. The Hybrid2 code test program is also discussed. Although every attempt has been made to make the Hybrid2 code easy to understand and use, this manual will allow many organizations to consider the long term advantages of using hybrid power systems instead of conventional petroleum based systems for remote power generation.

Baring-Gould, E.I.

1996-06-01T23:59:59.000Z

325

Hybrid Microwave Cavity Heat Engine  

E-Print Network (OSTI)

We propose and analyze the use of hybrid microwave cavities as quantum heat engines. A possible realization consists of two macroscopically separated quantum dot conductors coupled capacitively to the fundamental mode of a microwave cavity. We demonstrate that an electrical current can be induced in one conductor through cavity-mediated processes by heating up the other conductor. The heat engine can reach Carnot efficiency with optimal conversion of heat to work. When the system delivers the maximum power, the efficiency can be a large fraction of the Carnot efficiency. The heat engine functions even with moderate electronic relaxation and dephasing in the quantum dots. We provide detailed estimates for the electrical current and output power using realistic parameters.

Christian Bergenfeldt; Peter Samuelsson; Björn Sothmann; Christian Flindt; Markus Büttiker

2013-07-18T23:59:59.000Z

326

Cooling Evolution of Hybrid Stars  

E-Print Network (OSTI)

The cooling of compact isolated objects for different values of the gravitational mass has been simulated for two alternative assumptions. One is that the interior of the star is purely hadronic and second that the star can have a rather large quark core. It has been shown that within a nonlocal chiral quark model the critical density for a phase transition to color superconducting quark matter under neutron star conditions can be low enough for these phases to occur in compact star configurations with masses below 1.3 M_sun. For a realistic choice of parameters the equation of state (EoS) allows for 2SC quark matter with a large quark gap ~ 100 MeV for u and d quarks of two colors that coexists with normal quark matter within a mixed phase in the hybrid star interior. We argue that, if in the hadronic phase the neutron pairing gap in 3P_2 channel is larger than few keV and the phases with unpaired quarks are allowed, the corresponding hybrid stars would cool too fast. Even in the case of the essentially suppressed 3P_2 neutron gap if free quarks occur for M cooling data existing by today. It is suggested to discuss a "2SC+X" phase, as a possibility to have all quarks paired in two-flavor quark matter under neutron star constraints, where the X-gap is of the order of 10 keV - 1 MeV. Density independent gaps do not allow to fit the cooling data. Only the presence of an X-gap that decreases with increase of the density could allow to appropriately fit the data in a similar compact star mass interval to that following from a purely hadronic model.

H. Grigorian

2005-02-28T23:59:59.000Z

327

Hybridization and Selective Release of DNA Microarrays  

SciTech Connect

DNA microarrays contain sequence specific probes arrayed in distinct spots numbering from 10,000 to over 1,000,000, depending on the platform. This tremendous degree of multiplexing gives microarrays great potential for environmental background sampling, broad-spectrum clinical monitoring, and continuous biological threat detection. In practice, their use in these applications is not common due to limited information content, long processing times, and high cost. The work focused on characterizing the phenomena of microarray hybridization and selective release that will allow these limitations to be addressed. This will revolutionize the ways that microarrays can be used for LLNL's Global Security missions. The goals of this project were two-fold: automated faster hybridizations and selective release of hybridized features. The first study area involves hybridization kinetics and mass-transfer effects. the standard hybridization protocol uses an overnight incubation to achieve the best possible signal for any sample type, as well as for convenience in manual processing. There is potential to significantly shorten this time based on better understanding and control of the rate-limiting processes and knowledge of the progress of the hybridization. In the hybridization work, a custom microarray flow cell was used to manipulate the chemical and thermal environment of the array and autonomously image the changes over time during hybridization. The second study area is selective release. Microarrays easily generate hybridization patterns and signatures, but there is still an unmet need for methodologies enabling rapid and selective analysis of these patterns and signatures. Detailed analysis of individual spots by subsequent sequencing could potentially yield significant information for rapidly mutating and emerging (or deliberately engineered) pathogens. In the selective release work, optical energy deposition with coherent light quickly provides the thermal energy to single spots to release hybridized DNA. This work leverages LLNL expertise in optics, microfluids, and bioinformatics.

Beer, N R; Baker, B; Piggott, T; Maberry, S; Hara, C M; DeOtte, J; Benett, W; Mukerjee, E; Dzenitis, J; Wheeler, E K

2011-11-29T23:59:59.000Z

328

Hybrid Dynamic Density Functional Theory for Polymer Melts and Blends  

E-Print Network (OSTI)

We propose a high-speed and accurate hybrid dynamic density functional theory for the computer simulations of the phase separation processes of polymer melts and blends. The proposed theory is a combination of the dynamic self-consistent field (SCF) theory and a time-dependent Ginzburg-Landau type theory with the random phase approximation (GRPA). The SCF theory is known to be accurate in evaluating the free energy of the polymer systems in both weak and strong segregation regions although it has a disadvantage of the requirement of a considerable amount of computational cost. On the other hand, the GRPA theory has an advantage of much smaller amount of required computational cost than the SCF theory while its applicability is limited to the weak segregation region. To make the accuracy of the SCF theory and the high-performance of the GRPA theory compatible, we adjust the chemical potential of the GRPA theory by using the SCF theory every constant time steps in the dynamic simulations. The performance of the GRPA and the hybrid theories is tested by using several systems composed of an A/B homopolymer, an AB diblock copolymer, or an ABC triblock copolymer. Using the hybrid theory, we succeeded in reproducing the metastable complex phase-separated domain structures of an ABC triblock copolymer observed by experiments.

Takashi Honda; Toshihiro Kawakatsu

2006-09-05T23:59:59.000Z

329

Solid Oxide Fuel Cell Hybrid System for Distributed Power Generation  

SciTech Connect

This report summarizes the work performed by Hybrid Power Generation Systems, LLC (HPGS) during the April to October 2004 reporting period in Task 2.3 (SOFC Scaleup for Hybrid and Fuel Cell Systems) under Cooperative Agreement DE-FC26-01NT40779 for the U. S. Department of Energy, National Energy Technology Laboratory (DOE/NETL), entitled ''Solid Oxide Fuel Cell Hybrid System for Distributed Power Generation''. This study analyzes the performance and economics of power generation systems for central power generation application based on Solid Oxide Fuel Cell (SOFC) technology and fueled by natural gas. The main objective of this task is to develop credible scale up strategies for large solid oxide fuel cell-gas turbine systems. System concepts that integrate a SOFC with a gas turbine were developed and analyzed for plant sizes in excess of 20 MW. A 25 MW plant configuration was selected with projected system efficiency of over 65% and a factory cost of under $400/kW. The plant design is modular and can be scaled to both higher and lower plant power ratings. Technology gaps and required engineering development efforts were identified and evaluated.

David Deangelis; Rich Depuy; Debashis Dey; Georgia Karvountzi; Nguyen Minh; Max Peter; Faress Rahman; Pavel Sokolov; Deliang Yang

2004-09-30T23:59:59.000Z

330

Hybrid and conventional hydrogen engine vehicles that meet EZEV emissions  

DOE Green Energy (OSTI)

In this paper, a time-dependent engine model is used for predicting hydrogen engine efficiency and emissions. The model uses basic thermodynamic equations for the compression and expansion processes, along with an empirical correlation for heat transfer, to predict engine indicated efficiency. A friction correlation and a supercharger/turbocharger model are then used to calculate brake thermal efficiency. The model is validated with many experimental points obtained in a recent evaluation of a hydrogen research engine. A The validated engine model is then used to calculate fuel economy and emissions for three hydrogen-fueled vehicles: a conventional, a parallel hybrid, and a series hybrid. All vehicles use liquid hydrogen as a fuel. The hybrid vehicles use a flywheel for energy storage. Comparable ultra capacitor or battery energy storage performance would give similar results. This paper analyzes the engine and flywheel sizing requirements for obtaining a desired level of performance. The results indicate that hydrogen lean-burn spark-ignited engines can provide a high fuel economy and Equivalent Zero Emission Vehicle (EZEV) levels in the three vehicle configurations being analyzed.

Aceves, S.M.; Smith, J.R.

1996-12-10T23:59:59.000Z

331

Solid Oxide Fuel Cell Hybrid System for Distributed Power Generation  

DOE Green Energy (OSTI)

This report summarizes the work performed by Hybrid Power Generation Systems, LLC (HPGS) during the April to October 2004 reporting period in Task 2.3 (SOFC Scaleup for Hybrid and Fuel Cell Systems) under Cooperative Agreement DE-FC26-01NT40779 for the U. S. Department of Energy, National Energy Technology Laboratory (DOE/NETL), entitled ''Solid Oxide Fuel Cell Hybrid System for Distributed Power Generation''. This study analyzes the performance and economics of power generation systems for central power generation application based on Solid Oxide Fuel Cell (SOFC) technology and fueled by natural gas. The main objective of this task is to develop credible scale up strategies for large solid oxide fuel cell-gas turbine systems. System concepts that integrate a SOFC with a gas turbine were developed and analyzed for plant sizes in excess of 20 MW. A 25 MW plant configuration was selected with projected system efficiency of over 65% and a factory cost of under $400/kW. The plant design is modular and can be scaled to both higher and lower plant power ratings. Technology gaps and required engineering development efforts were identified and evaluated.

David Deangelis; Rich Depuy; Debashis Dey; Georgia Karvountzi; Nguyen Minh; Max Peter; Faress Rahman; Pavel Sokolov; Deliang Yang

2004-09-30T23:59:59.000Z

332

SOLID OXIDE FUEL CELL HYBRID SYSTEM FOR DISTRIBUTED POWER GENERATION  

DOE Green Energy (OSTI)

This report summarizes the work performed by Hybrid Power Generation Systems, LLC during the January 2003 to June 2003 reporting period under Cooperative Agreement DE-FC26-01NT40779 for the U. S. Department of Energy, National Energy Technology Laboratory (DOE/NETL) entitled ''Solid Oxide Fuel Cell Hybrid System for Distributed Power Generation''. The main objective of this project is to develop and demonstrate the feasibility of a highly efficient hybrid system integrating a planar Solid Oxide Fuel Cell (SOFC) and a micro-turbine. In addition, an activity included in this program focuses on the development of an integrated coal gasification fuel cell system concept based on planar SOFC technology. This report summarizes the results obtained to date on: System performance analysis and model optimization; Reliability and cost model development; System control including dynamic model development; Heat exchanger material tests and life analysis; Pressurized SOFC evaluation; and Pre-baseline system definition for coal gasification fuel cell system concept.

Faress Rahman; Nguyen Minh

2003-07-01T23:59:59.000Z

333

Alternative Fuels Data Center: Hybrid Electric Vehicle (HEV) Taxicab  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Hybrid Electric Hybrid Electric Vehicle (HEV) Taxicab Restriction Exemption to someone by E-mail Share Alternative Fuels Data Center: Hybrid Electric Vehicle (HEV) Taxicab Restriction Exemption on Facebook Tweet about Alternative Fuels Data Center: Hybrid Electric Vehicle (HEV) Taxicab Restriction Exemption on Twitter Bookmark Alternative Fuels Data Center: Hybrid Electric Vehicle (HEV) Taxicab Restriction Exemption on Google Bookmark Alternative Fuels Data Center: Hybrid Electric Vehicle (HEV) Taxicab Restriction Exemption on Delicious Rank Alternative Fuels Data Center: Hybrid Electric Vehicle (HEV) Taxicab Restriction Exemption on Digg Find More places to share Alternative Fuels Data Center: Hybrid Electric Vehicle (HEV) Taxicab Restriction Exemption on AddThis.com...

334

Hybrid and Plug-In Electric Vehicles (Brochure)  

DOE Green Energy (OSTI)

Describes the basics of electric-drive vehicles, including hybrid electric vehicles, plug-in hybrid electric vehicles, all-electric vehicles, and the various charging options.

Not Available

2011-05-01T23:59:59.000Z

335

Hybrid and Plug-In Electric Vehicles (Brochure)  

DOE Green Energy (OSTI)

Describes the basics of electric-drive vehicles, including hybrid electric vehicles, plug-in hybrid electric vehicles, all-electric vehicles, and the various charging options.

Not Available

2011-10-01T23:59:59.000Z

336

STATEMENT OF CONSIDERATIONS REQUEST BY HYBRID POWER GENERATION...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

of a highly efficient hybrid system integrating a planar Solid Oxide Fuel Cell (SOFC) and a turbogenerator. The proposed hybrid system is based on planar SOFC and...

337

Performance analysis of hybrid liquid desiccant solar cooling system.  

E-Print Network (OSTI)

??This thesis investigates the coefficient of performance (COP) of a hybrid liquid desiccant solar cooling system. This hybrid cooling system includes three sections: 1) conventional… (more)

Zhou, Zhipeng (Joe Zoe)

2009-01-01T23:59:59.000Z

338

Advanced Vehicle Testing Activity: 2004 Toyota Prius Hybrid Electric...  

NLE Websites -- All DOE Office Websites (Extended Search)

4 Toyota Prius Hybrid Electric Vehicle Accelerated Reliability Testing - October 2007 to someone by E-mail Share Advanced Vehicle Testing Activity: 2004 Toyota Prius Hybrid...

339

Advanced Vehicle Testing Activity: Honda Accord Hybrid Electric...  

NLE Websites -- All DOE Office Websites (Extended Search)

Accord Hybrid Electric Vehicle Accelerated Reliability Testing - April 2008 to someone by E-mail Share Advanced Vehicle Testing Activity: Honda Accord Hybrid Electric Vehicle...

340

Mechanical and Regenerative Braking Integration for a Hybrid Electric Vehicle.  

E-Print Network (OSTI)

??Hybrid electric vehicle technology has become a preferred method for the automotive industry to reduce environmental impact and fuel consumption of their vehicles. Hybrid electric… (more)

DeMers, Steven Michael

2008-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "hybrid tractor evaluation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Synthesis and properties of chitosan-silica hybrid aerogels  

NLE Websites -- All DOE Office Websites (Extended Search)

Synthesis and properties of chitosan-silica hybrid aerogels Title Synthesis and properties of chitosan-silica hybrid aerogels Publication Type Journal Article Year of Publication...

342

Ultracapacitor Technologies and Application in Hybrid and Electric Vehicles  

E-Print Network (OSTI)

Moderate Hybrid-electric Vehicles. ESScap06, Switzerland,GH. SIMPLEV: A Simple Electric Vehicle Simulation Program-Ultracapacitors in Hybrid- electric Vehicle Applications.

Burke, Andy

2009-01-01T23:59:59.000Z

343

Optimum Performance of Direct Hydrogen Hybrid Fuel Cell Vehicles  

E-Print Network (OSTI)

batteries and ultracapacitors for electric vehicles. EVS24Battery, Hybrid and Fuel Cell Electric Vehicle Symposiumpublications on electric and hybrid vehicle technology and

Zhao, Hengbing; Burke, Andy

2009-01-01T23:59:59.000Z

344

Materials for Motors of Hybrid Automobiles - Programmaster.org  

Science Conference Proceedings (OSTI)

To realize the sustainable mobility society, Hybrid vehicle could be one of the good candidates as eco-friendly car. In this speech, the benefit of Hybrid vehicle  ...

345

King County Metro Transit: Allison Hybrid Electric Transit Bus...  

NLE Websites -- All DOE Office Websites (Extended Search)

advanced hybrid electric drivetrain. Both vehicles also incorporated an oxidizing diesel particulate filter. The fuel economy and emissions benefits of the hybrid vehicle were...

346

Platform Engineering Applied to Plug-In Hybrid Electric Vehicles  

SciTech Connect

This paper quantifies the relative impacts of each platform engineering step on conventional, hybrid, and plug-in hybrid vehicle architectures.

Markel, T.

2007-05-01T23:59:59.000Z

347

Environmental Assessment of Plug-In Hybrid Electric Vehicles...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Environmental Assessment of Plug-In Hybrid Electric Vehicles Volume 1: Nationwide Greenhouse Gas Emissions Environmental Assessment of Plug-In Hybrid Electric Vehicles Volume 1:...

348

HYSPEC: the Hybrid Spectrometer at SNS | ORNL Neutron Sciences  

NLE Websites -- All DOE Office Websites (Extended Search)

Hybrid Spectrometer at SNS Hybrid Spectrometer Schematic of the HYSPEC instrument Developed by a team from leading U.S. universities and national laboratories and an international...

349

Design and Development of Hybrid Nanoparticles for Energy and...  

NLE Websites -- All DOE Office Websites (Extended Search)

PRESENTATION PRESENTATION " " Design and Development of Design and Development of Hybrid Hybrid Nanoparticles Nanoparticles for for Energy and Biomedical Energy and Biomedical...

350

Affordable Cold Climate Infill Housing with Hybrid Insulation...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

with Hybrid Insulation Approach Affordable Cold Climate Infill Housing with Hybrid Insulation Approach, Wyandotte, Michigan (Fact Sheet), Building America Case Study:...

351

Hybrid and electric advanced vehicle systems (heavy) simulation. Final report  

Science Conference Proceedings (OSTI)

A computer program to simulate hybrid and electric advanced vehicle systems (HEAVY) is described. It is intended for use early in the design process: concept evaluation, alternative comparison, preliminary design, control and management strategy development, component sizing, and sensitivity studies. It allows the designer to quickly, conveniently, and economically predict the performance of a proposed drive train. The user defines the system to be simulated using a library of predefined component models that may be connected to represent a wide variety of propulsion systems. The development of three models are discussed as examples.

Hammond, R.A.; McGehee, R.K.

1981-11-01T23:59:59.000Z

352

Performance characteristics of hybrid MPI/OpenMP implementations of NAS parallel benchmarks SP and BT on large-scale multicore supercomputers  

Science Conference Proceedings (OSTI)

The NAS Parallel Benchmarks (NPB) are well-known applications with the fixed algorithms for evaluating parallel systems and tools. Multicore supercomputers provide a natural programming paradigm for hybrid programs, whereby OpenMP can be used with the ... Keywords: Hybrid MPI/OpenMP, NAS parallel benchmarks, benchmarks, multicore, performance characteristics, supercomputers

Xingfu Wu; Valerie Taylor

2011-03-01T23:59:59.000Z

353

Prototype testing for a hybrid gas-gun/railgun device  

DOE Green Energy (OSTI)

In 1984 Los Alamos began the design of the lethality test system (LTS), a facility to be used for the study of impact physics at velocities up to 15 km/s. The key component of LTS was an electromagnetic launcher capable of accelerating a 30 gram mass to 15 km/s. By the time of the Preliminary Design Review (July 1985) it was known from laboratory experiments that a conventional railgun was incapable of reaching 15 km/s starting at low velocity (/approximately/1 km/s) and a hybrid design was adopted for the LTS launcher. The hybrid launcher consisted of a two-stage hydrogen gun that preaccelerated the test mass to 6.5 km/s and an electromagnetic launcher for the final acceleration from 6.5 to 15 km/s. Design calculations predicted that injection into the railgun at 6.5 km/s would reduce ablation sufficiently to permit operation at 12 km/s with reasonable probability of achieving 15 km/s. The hybrid launcher design adopted for LTS presents some unique mechanical and electrical issues. In particular, the hybrid design requires that the plasma armature be established in a high pressure gas environment behind the projectile. To address this issue, as well as to evaluate the mechanical and electrical design, an 1.83 meter long prototype of the electromagnetic launcher barrel was built and tested. This paper describes the prototype launcher tests and the performance achieved. In addition, testing of a plasma initiator operating in a high pressure gas environment is discussed. 5 refs., 11 figs., 1 tab.

Parker, J.V.

1989-01-01T23:59:59.000Z

354

Analysis of data from electric and hybrid electric vehicle student competitions  

DOE Green Energy (OSTI)

The US Department of Energy sponsored several student engineering competitions in 1993 that provided useful information on electric and hybrid electric vehicles. The electrical energy usage from these competitions has been recorded with a custom-built digital meter installed in every vehicle and used under controlled conditions. When combined with other factors, such as vehicle mass, speed, distance traveled, battery type, and type of components, this information provides useful insight into the performance characteristics of electrics and hybrids. All the vehicles tested were either electric vehicles or hybrid vehicles in electric-only mode, and had an average energy economy of 7.0 km/kwh. Based on the performance of the ``ground-up`` hybrid electric vehicles in the 1993 Hybrid Electric Vehicle Challenge, data revealed a I km/kwh energy economy benefit for every 133 kg decrease in vehicle mass. By running all the electric vehicles at a competition in Atlanta at several different constant speeds, the effects of rolling resistance and aerodynamic drag were evaluated. On average, these vehicles were 32% more energy efficient at 40 km/h than at 72 km/h. The results of the competition data analysis confirm that these engineering competitions not only provide an educational experience for the students, but also show technology performance and improvements in electric and hybrid vehicles by setting benchmarks and revealing trends.

Wipke, K.B. [National Renewable Energy Lab., Golden, CO (United States); Hill, N.; Larsen, R.P. [Argonne National Lab., IL (United States)

1994-01-01T23:59:59.000Z

355

Spectroscopy identification performance enhancement of a novel CZT/CsI hybrid system  

Science Conference Proceedings (OSTI)

New hybrid spectroscopic systems directly combine spectra from detectors with very different energy resolutions, accommodating standard analyses of the output hybrid spectrum. Simulations of a hybrid system consisting of a 2 or 4 cm{sup 3} cadmium zinc telluride detector combined with a 32.8 cm{sup 3} CsI(Tl) were evaluated for identification performance. 29 nuclides of interest for security applications were simulated as singles and unique pairs, producing 435 spectral simulations at live times of 3, 10, 30, 100 and 300 seconds. The nuclides were modeled as point sources at 25 cm with activities that provide an interesting range of statistical significance for the range of counting times. Standard nuclide identification analyses were applied to the component detectors as well as the hybrid combination. Tallies of the results were used to calculate true and false identification rates. The hybrid system was shown to provide an identification performance benefit, consistently achieving performances closest to ideal relative to the separate component detectors. The hybrid approach enables the consideration of a greater variety of measurement system solutions in terms of cost and performance. (authors)

Russ, W.; Nakazawa, D.; Hau, I.; Morichi, M. [Canberra Industries, Inc., AREVA Company (United States)

2011-07-01T23:59:59.000Z

356

Alternative Fuels Data Center: Heavy-Duty Vehicle and Engine...  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Vision Motor Corp. - Tyrano Application: Tractor Fuel Type: Hydrogen Power Source(s): Vision Motor Corp. - 65kW Hydrogen Fuel Cell Hybrid System(s): Eaton - Hybrid Drive System...

357

Powertrain system for a hybrid electric vehicle  

DOE Patents (OSTI)

A hybrid electric powertrain system is provided including an electric motor/generator drivingly engaged with the drive shaft of a transmission. The electric is utilized for synchronizing the rotation of the drive shaft with the driven shaft during gear shift operations. In addition, a mild hybrid concept is provided which utilizes a smaller electric motor than typical hybrid powertrain systems. Because the electric motor is drivingly engaged with the drive shaft of the transmission, the electric motor/generator is driven at high speed even when the vehicle speed is low so that the electric motor/generator provides more efficient regeneration. 34 figs.

Reed, R.G. Jr.; Boberg, E.S.; Lawrie, R.E.; Castaing, F.J.

1999-08-31T23:59:59.000Z

358

Powertrain system for a hybrid electric vehicle  

DOE Patents (OSTI)

A hybrid electric powertrain system is provided including an electric motor/generator drivingly engaged with the drive shaft of a transmission. The electric is utilized for synchronizing the rotation of the drive shaft with the driven shaft during gear shift operations. In addition, a mild hybrid concept is provided which utilizes a smaller electric motor than typical hybrid powertrain systems. Because the electric motor is drivingly engaged with the drive shaft of the transmission, the electric motor/generator is driven at high speed even when the vehicle speed is low so that the electric motor/generator provides more efficient regeneration.

Reed, Jr., Richard G. (Royal Oak, MI); Boberg, Evan S. (Hazel Park, MI); Lawrie, Robert E. (Whitmore Lake, MI); Castaing, Francois J. (Bloomfield Township, MI)

1999-08-31T23:59:59.000Z

359

NREL: Vehicles and Fuels Research - Fleet Test and Evaluation  

NLE Websites -- All DOE Office Websites (Extended Search)

Research Research Search More Search Options Site Map The Fleet Test and Evaluation Team at the National Renewable Energy Laboratory works in partnership with commercial and government fleets and industry groups to evaluate the performance of alternative fuels and advanced technologies in medium- and heavy-duty fleet vehicles. The team's project areas include: Fleet DNA: Vehicle Drive Cycle Analysis Hybrid Electric Drive Systems Electric and Plug-in Hybrid Electric Drive Systems Hydraulic Hybrid Drive Systems Truck Stop Electrification Alternative Fuels Truck Efficiency Key aspects of this work involve meeting with industry stakeholders to understand market factors and customer requirements, evaluating the performance of advanced technology vehicles versus their conventional

360

NETL: Bench-Scale Development of a Hybrid Membrane-Absorption CO2 Capture  

NLE Websites -- All DOE Office Websites (Extended Search)

Bench-Scale Development of a Hybrid Membrane-Absorption CO2 Capture Process Bench-Scale Development of a Hybrid Membrane-Absorption CO2 Capture Process Project No.: DE-FE0013118 Membrane Technology and Research (MTR) is developing and evaluating a hybrid membrane-absorption CO2 capture system. This work builds on prior DOE-funded work and combines MTR's Polaris(tm) membrane, in a low-pressure-drop, large area, plate-and-frame module, with UT Austin's piperazine (PZ) solvent and advanced, high-temperature and pressure regeneration technology. Preliminary estimates indicate that this hybrid system could lower the regeneration energy by 30 percent compared to that required with 30 weight percent monoethanolamine (MEA). MTR is evaluating two variations of the hybrid design consisting of the cross-flow Polaris membrane, which enriches flue gas to approximately 20 percent CO2, and an advanced 5 molal PZ advanced flash stripper with cold-rich bypass. The flash stripper will be optimized to take advantage of the higher CO2 concentration. In the first variation, the two systems are operated in series; in the second, the flue gas flow is split and treated by each system in parallel. The first phase of this project will include an examination of both hybrid configurations, using an integrated process model and a preliminary techno-economic assessment. In the second phase, MTR will manufacture and test a low pressure drop, large-area membrane module and UT Austin will modify their 0.1 MWe pilot plant and operate it under simulated series and parallel configurations. Based on the model and test results, the most promising configuration will be identified. In the final stage of the project, the membrane module will be integrated into the pilot plant where the fully integrated hybrid system, in its most promising cost optimized configuration, will be tested on simulated flue gas.

Note: This page contains sample records for the topic "hybrid tractor evaluation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

NREL: Fleet Test and Evaluation - Alternative Fuels  

NLE Websites -- All DOE Office Websites (Extended Search)

Alternative Fuels Alternative Fuels NREL's Fleet Test and Evaluation Team works with industry partners to evaluate the use of alternative fuels in delivery, transit, and freight vehicles. Although biodiesel is the most commonly used alternative fuel in medium- and heavy-duty diesel vehicles, compressed and liquefied natural gas and Fischer-Tropsch diesel are also viable options for trucking companies. Learn more about the team's evaluations of alternative fuels in fleet operations: Biodiesel Compressed Natural Gas Fischer-Tropsch Diesel Liquefied Natural Gas Printable Version Fleet Test and Evaluation Home Research & Development Vehicle Drive Cycle Analysis Hybrid Electric Drive Systems Electric & Plug-in Hybrid Electric Drive Systems Hydraulic Hybrid Drive Systems Truck Stop Electrification

362

Hybrid Rotaxanes: Interlocked Structures for Quantum Computing?  

NLE Websites -- All DOE Office Websites (Extended Search)

Hybrid Rotaxanes: Interlocked Structures for Quantum Computing? Print Hybrid Rotaxanes: Interlocked Structures for Quantum Computing? Print Rotaxanes are mechanically interlocked molecular architectures consisting of a dumbbell-shaped molecule, the "axle," that threads through a ring called a macrocycle. Because the rings can spin around and slide along the axle, rotaxanes are promising components of molecular machines. While most rotaxanes have been entirely organic, the physical properties desirable in molecular machines are mostly found in inorganic compounds. Working together, two British groups at the University of Edinburgh and the University of Manchester have bridged this gap with hybrid rotaxanes, in which inorganic rings encircle the organic axles. The hybrid architecture greatly increases their range of useful physical properties, such as the magnetism based on molecular magnets that may make them suitable as qubits for quantum computers.

363

Hybrid Rotaxanes: Interlocked Structures for Quantum Computing?  

NLE Websites -- All DOE Office Websites (Extended Search)

Hybrid Rotaxanes: Interlocked Structures for Quantum Computing? Print Hybrid Rotaxanes: Interlocked Structures for Quantum Computing? Print Rotaxanes are mechanically interlocked molecular architectures consisting of a dumbbell-shaped molecule, the "axle," that threads through a ring called a macrocycle. Because the rings can spin around and slide along the axle, rotaxanes are promising components of molecular machines. While most rotaxanes have been entirely organic, the physical properties desirable in molecular machines are mostly found in inorganic compounds. Working together, two British groups at the University of Edinburgh and the University of Manchester have bridged this gap with hybrid rotaxanes, in which inorganic rings encircle the organic axles. The hybrid architecture greatly increases their range of useful physical properties, such as the magnetism based on molecular magnets that may make them suitable as qubits for quantum computers.

364

Hybrid Rotaxanes: Interlocked Structures for Quantum Computing?  

NLE Websites -- All DOE Office Websites (Extended Search)

Hybrid Rotaxanes: Interlocked Structures for Quantum Computing? Print Hybrid Rotaxanes: Interlocked Structures for Quantum Computing? Print Rotaxanes are mechanically interlocked molecular architectures consisting of a dumbbell-shaped molecule, the "axle," that threads through a ring called a macrocycle. Because the rings can spin around and slide along the axle, rotaxanes are promising components of molecular machines. While most rotaxanes have been entirely organic, the physical properties desirable in molecular machines are mostly found in inorganic compounds. Working together, two British groups at the University of Edinburgh and the University of Manchester have bridged this gap with hybrid rotaxanes, in which inorganic rings encircle the organic axles. The hybrid architecture greatly increases their range of useful physical properties, such as the magnetism based on molecular magnets that may make them suitable as qubits for quantum computers.

365

Hybrid Rotaxanes: Interlocked Structures for Quantum Computing?  

NLE Websites -- All DOE Office Websites (Extended Search)

Hybrid Rotaxanes: Interlocked Structures for Quantum Computing? Print Hybrid Rotaxanes: Interlocked Structures for Quantum Computing? Print Rotaxanes are mechanically interlocked molecular architectures consisting of a dumbbell-shaped molecule, the "axle," that threads through a ring called a macrocycle. Because the rings can spin around and slide along the axle, rotaxanes are promising components of molecular machines. While most rotaxanes have been entirely organic, the physical properties desirable in molecular machines are mostly found in inorganic compounds. Working together, two British groups at the University of Edinburgh and the University of Manchester have bridged this gap with hybrid rotaxanes, in which inorganic rings encircle the organic axles. The hybrid architecture greatly increases their range of useful physical properties, such as the magnetism based on molecular magnets that may make them suitable as qubits for quantum computers.

366

Highline Hydrogen Hybrids | Open Energy Information  

Open Energy Info (EERE)

Hydrogen Hybrids Hydrogen Hybrids Jump to: navigation, search Name Highline Hydrogen Hybrids Place farmington, Arkansas Zip 72730-1500 Sector Hydro, Hydrogen, Vehicles Product US-based manufacturer of hydrogen conversion systems for gasoline and diesel-powered vehicles. Coordinates 43.533982°, -88.093717° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":43.533982,"lon":-88.093717,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

367

Tough, bio-inspired hybrid materials  

E-Print Network (OSTI)

Tough, bio-inspired hybrid materials E. Munch, 1 M. E.guide the synthesis of bio-inspired ceramic-based compositesLike many hard mineralized bio-composites, the ice-templated

Munch, Etienne

2009-01-01T23:59:59.000Z

368

Argonne CNM Highlight: Improved Hybrid Solar Cells  

NLE Websites -- All DOE Office Websites (Extended Search)

Improved Hybrid Solar Cells Improved Hybrid Solar Cells inorganic-organic hybrid photovoltaic (PV) cells imade of highly ordered titanium dioxide (TiO2) nanotube arrays filled with solid organic hole conductors such as conjugated polymers One approach for making inexpensive inorganic-organic hybrid photovoltaic (PV) cells is to fill highly ordered titanium dioxide (TiO2) nanotube arrays with solid organic hole conductors such as conjugated polymers. Center for Nanoscale Materials researchers and collaborative users from the University of Chicago present a new in situ ultraviolet (UV) polymerization method for growing polythiophene inside TiO2 nanotubes and compare this method to the conventional approach of infiltrating nanotubes with presynthesized polymer. A nanotubular TiO2 substrate is immersed in a 2,5-diiodothiophene (DIT)

369

Hybrid Rotaxanes: Interlocked Structures for Quantum Computing?  

NLE Websites -- All DOE Office Websites (Extended Search)

Hybrid Rotaxanes: Interlocked Structures for Quantum Computing? Print Hybrid Rotaxanes: Interlocked Structures for Quantum Computing? Print Rotaxanes are mechanically interlocked molecular architectures consisting of a dumbbell-shaped molecule, the "axle," that threads through a ring called a macrocycle. Because the rings can spin around and slide along the axle, rotaxanes are promising components of molecular machines. While most rotaxanes have been entirely organic, the physical properties desirable in molecular machines are mostly found in inorganic compounds. Working together, two British groups at the University of Edinburgh and the University of Manchester have bridged this gap with hybrid rotaxanes, in which inorganic rings encircle the organic axles. The hybrid architecture greatly increases their range of useful physical properties, such as the magnetism based on molecular magnets that may make them suitable as qubits for quantum computers.

370

Advanced Vehicle Testing Activity - Hybrid Electric Vehicles  

NLE Websites -- All DOE Office Websites (Extended Search)

Hybrid Electric Vehicles What's New 2012 Hyundai Sonata (4932) Battery Report (PDF 574KB) 2010 Ultra-Battery Honda Civic Battery Report (PDF 614KB) 2013 Chevrolet Malibu Baseline...

371

Hybrid Silicon Photonic Integrated Circuit Technology  

E-Print Network (OSTI)

modulators for sili- con photonics,” in Proc. IEEE Photon.J.E. Bowers, “Hybrid silicon photonics for optical Intercon-The evolution of silicon photonics as an enabling technology

2013-01-01T23:59:59.000Z

372

Advanced Coal Wind Hybrid: Economic Analysis  

E-Print Network (OSTI)

Advanced Coal-Wind Non-Hybrid SNG IGCC+CCS PC CCGT Windor a synthetic natural gas (SNG) production facility) and anwithout Fuel With with SNG Production or Syncrude Production

Phadke, Amol

2008-01-01T23:59:59.000Z

373

Travelling waves in hybrid chemotaxis models  

E-Print Network (OSTI)

Hybrid models of chemotaxis combine agent-based models of cells with partial differential equation models of extracellular chemical signals. In this paper, travelling wave properties of hybrid models of bacterial chemotaxis are investigated. Bacteria are modelled using an agent-based (individual-based) approach with internal dynamics describing signal transduction. In addition to the chemotactic behaviour of the bacteria, the individual-based model also includes cell proliferation and death. Cells consume the extracellular nutrient field (chemoattractant) which is modelled using a partial differential equation. Mesoscopic and macroscopic equations representing the behaviour of the hybrid model are derived and the existence of travelling wave solutions for these models is established. It is shown that cell proliferation is necessary for the existence of non-transient (stationary) travelling waves in hybrid models. Additionally, a numerical comparison between the wave speeds of the continuum models and the hybr...

Franz, Benjamin; Painter, Kevin J; Erban, Radek

2013-01-01T23:59:59.000Z

374

Hybrid electric vehicles take to the streets  

Science Conference Proceedings (OSTI)

In this paper, the authors describe how, equipped with a gasoline engine and an electric motor, hybrid electric vehicles can now bridge the gap between vehicle range and environmental concerns

D. Hermance; S. Sasaki

1998-11-01T23:59:59.000Z

375

Issue 5: High Interest in Hybrid Cars  

E-Print Network (OSTI)

Reports. (2005). “Which Cars Would People Get Again? ” Con-Motor Trend Announces 2004 Car of the Year. ” Motor Trend,Oregon Hybrid Gas-Electric Car Owners. July. U.S. Internal

Ong, Paul M.; Haselhoff, Kim

2005-01-01T23:59:59.000Z

376

Hybrid hierarchical learning from dynamic scenes  

Science Conference Proceedings (OSTI)

The work proposes a hierarchical architecture for learning from dynamic scenes at various levels of knowledge abstraction. The raw visual information is processed at different stages to generate hybrid symbolic/sub-symbolic descriptions of the scene, ...

Prithwijit Guha; Pradeep Vaghela; Pabitra Mitra; K. S. Venkatesh; Amitabha Mukerjee

2005-12-01T23:59:59.000Z

377

Fuel Savings from Hybrid Electric Vehicles  

DOE Green Energy (OSTI)

NREL's study shows that hybrid electric vehicles can significantly reduce oil imports for use in light-duty vehicles, particularly if drivers switch to smaller, more fuel-efficient vehicles overall.

Bennion, K.; Thornton, M.

2009-03-01T23:59:59.000Z

378

HEV Fleet Testing - 2001 Honda Insight Hybrid  

NLE Websites -- All DOE Office Websites (Extended Search)

1 - Honda Insight Hybrid VIN JHMZE14781T002163 Date Mileage Description Cost 2202002 7,595 Changed oil, rotated tires 27.00 592002 15,119 15K service 160.21 6142002 19,290...

379

Advanced Coal Wind Hybrid: Economic Analysis  

E-Print Network (OSTI)

Coal prices have been far less volatile than natural gas prices.Coal Prices Figure 9 is similar to Figure 8 except the natural gas pricesCoal Wind Hybrid: Economic Analysis interested in natural gas prices

Phadke, Amol

2008-01-01T23:59:59.000Z

380

Quantifying the benefits of hybrid vehicles  

E-Print Network (OSTI)

per month; one model, the Toyota Prius has reached salesand their halo effect on Toyota and Honda have spurred abattery. Blending power Toyota’s Hybrid Synergy Drive™ uses

Turrentine, Tom; Delucchi, Mark; Heffner, Reid R.; Kurani, Kenneth S; Sun, Yongling

2006-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "hybrid tractor evaluation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Experimental Study of Hybrid Cooled Heat Exchanger.  

E-Print Network (OSTI)

??A test system for a hybrid cooled heat exchanger was designed, and the test facility was constructed based on ASHRAE Standard 41.2-1987. A conventional air-cooled… (more)

Tsao, Han-Chuan

2011-01-01T23:59:59.000Z

382

Hybrid staging of geothermal energy conversion process  

DOE Green Energy (OSTI)

Progress in the demonstration of the feasibility of hybrid staging in geothermal energy conversion is described, particularly processes involving the Lysholm engine. The performance limitations of the Lysholm engine were studied. (MHR)

Steidel, R.F. Jr.

1984-05-07T23:59:59.000Z

383

Study of Hybrid Geothermal Heat Pump Systems  

Science Conference Proceedings (OSTI)

Hybrid Ground Source Heat Pump systems often combine a traditional geothermal system with either a cooling tower or fluid cooler for heat rejection and a boiler or solar heat collector for heat addition to the loop. These systems offer the same energy efficiency benefits as full geothermal systems to utilities and their customers but at a potentially lower first cost. Many hybrid systems have materialized to resolve heat buildup in full geothermal system loops where loop temperatures continue to rise as ...

2010-12-06T23:59:59.000Z

384

Analysis of Hybrid Hydrogen Systems: Final Report  

DOE Green Energy (OSTI)

Report on biomass pathways for hydrogen production and how they can be hybridized to support renewable electricity generation. Two hybrid systems were studied in detail for process feasibility and economic performance. The best-performing system was estimated to produce hydrogen at costs ($1.67/kg) within Department of Energy targets ($2.10/kg) for central biomass-derived hydrogen production while also providing value-added energy services to the electric grid.

Dean, J.; Braun, R.; Munoz, D.; Penev, M.; Kinchin, C.

2010-01-01T23:59:59.000Z

385

Use of Hybrid Rendering Styles for Presentation  

E-Print Network (OSTI)

This paper presents hybrid rendering that combines the use of photorealistic and non-photorealistic rendering styles in the same image. This allows to extend the set of expression dimensions available in a visualization environment. To provide general applicability, this use of hybrid rendering styles is controlled by an XML-based scene description. We discuss the according schema definition and present an architecture for implementing the presented methods as well as two exemplary applications.

Roland Jesse; Tobias Isenberg

2003-01-01T23:59:59.000Z

386

Mixed-hybrid discretization methods for the P1 equations  

Science Conference Proceedings (OSTI)

We consider mixed-hybrid discretization methods for the linear Boltzmann transport equation which is extensively used in computational neutron transport. Mixed-hybrid methods combine attractive features of both mixed and hybrid methods, namely the simultaneous ... Keywords: 02.60.Cb, 02.70.Dh, 65N12, 65N30, Linear Boltzmann transport equation, Mixed-hybrid discretization methods, P1 approximation

S. Van Criekingen; R. Beauwens

2007-02-01T23:59:59.000Z

387

Super Energy Saver Heat Pump with Dynamic Hybrid Phase Change ...  

Super Energy Saver Heat Pump with Dynamic Hybrid Phase Change Material United States Patent Application

388

Modeling and Simulation of Hybrid Electric Yuliang Leon Zhou  

E-Print Network (OSTI)

Modeling and Simulation of Hybrid Electric Vehicles By Yuliang Leon Zhou B. Eng., University and Simulation of Hybrid Electric Vehicles By Yuliang Leon Zhou B.Eng., University of Science and Technology and analysis of next generation hybrid electric vehicles, exploring the potentials of new hybrid powertrain

Victoria, University of

389

Predictive energy management for hybrid electric vehicles -Prediction horizon and  

E-Print Network (OSTI)

Predictive energy management for hybrid electric vehicles - Prediction horizon and battery capacity of a combined hybrid electric vehicle. Keywords: Hybrid vehicles, Energy Management, Predictive control, Optimal on a sliding window in order to minimize the hybrid vehicle fuel consumption. For real time implementation

Paris-Sud XI, Université de

390

Perspective on the fusion-fission hybrid reactor  

SciTech Connect

The hybrid reactor's role as a source of fuel for fission converter reactors is investigated. The role of the hybrid reactor in the energy economy, the interface between the hybrid reactor and the present fusion program, implications of the Carter Energy Plan, and the rationale for further hybrid reactor studies are discussed.

Bender, D.J.; Lee, J.D.; Moir, R.W.

1977-10-01T23:59:59.000Z

391

Adaptive hybrid impedance control of robot manipulators: a comparative study  

Science Conference Proceedings (OSTI)

Keywords: direct adaptive control, hybrid impedance control, passivity-based adaptive control, robotics

Luís F. Baptista; José M. G. Sá da Costa

1997-01-01T23:59:59.000Z

392

Hydraulic Hybrid Systems | Open Energy Information  

Open Energy Info (EERE)

Hydraulic Hybrid Systems Hydraulic Hybrid Systems Jump to: navigation, search Logo: Hydraulic Hybrid Systems Name Hydraulic Hybrid Systems Address 320 N. Railroad Ave Place Loveland, Colorado Zip 80537 Sector Vehicles Product hydraulic hybrid system for light-duty vehicles Year founded 2008 Number of employees 11-50 Phone number 303-519-4144 Website http://www.hydraulichybridsyst Coordinates 40.394833°, -105.0758931° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":40.394833,"lon":-105.0758931,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

393

Demand Response Performance of GE Hybrid Heat Pump Water Heater  

SciTech Connect

This report describes a project to evaluate and document the DR performance of HPWH as compared to ERWH for two primary types of DR events: peak curtailments and balancing reserves. The experiments were conducted with GE second-generation “Brillion”-enabled GeoSpring hybrid water heaters in the PNNL Lab Homes, with one GE GeoSpring water heater operating in “Standard” electric resistance mode to represent the baseline and one GE GeoSpring water heater operating in “Heat Pump” mode to provide the comparison to heat pump-only demand response. It is expected that “Hybrid” DR performance, which would engage both the heat pump and electric elements, could be interpolated from these two experimental extremes. Signals were sent simultaneously to the two water heaters in the side-by-side PNNL Lab Homes under highly controlled, simulated occupancy conditions. This report presents the results of the evaluation, which documents the demand-response capability of the GE GeoSpring HPWH for peak load reduction and regulation services. The sections describe the experimental protocol and test apparatus used to collect data, present the baselining procedure, discuss the results of the simulated DR events for the HPWH and ERWH, and synthesize key conclusions based on the collected data.

Widder, Sarah H.; Parker, Graham B.; Petersen, Joseph M.; Baechler, Michael C.

2013-07-01T23:59:59.000Z

394

Assimilating AMSU-A Radiances in TC Core Area with NOAA Operational HWRF (2011) and a Hybrid Data Assimilation System: Danielle (2010)  

Science Conference Proceedings (OSTI)

A regional hybrid variational-ensemble data assimilation system (HVEDAS), the Maximum Likelihood Ensemble Filter (MLEF), is applied to the 2011 version of the NOAA operational Hurricane Weather Research and Forecasting (HWRF) model to evaluate the ...

Man Zhang; Milija Zupanski; Min-Jeong Kim; John A. Knaff

395

Alternative Fuels Data Center: State Hybrid Electric (HEV) Alternative Fuel  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

State Hybrid Electric State Hybrid Electric (HEV) Alternative Fuel Vehicle (AFV) Acquisition Requirements to someone by E-mail Share Alternative Fuels Data Center: State Hybrid Electric (HEV) Alternative Fuel Vehicle (AFV) Acquisition Requirements on Facebook Tweet about Alternative Fuels Data Center: State Hybrid Electric (HEV) Alternative Fuel Vehicle (AFV) Acquisition Requirements on Twitter Bookmark Alternative Fuels Data Center: State Hybrid Electric (HEV) Alternative Fuel Vehicle (AFV) Acquisition Requirements on Google Bookmark Alternative Fuels Data Center: State Hybrid Electric (HEV) Alternative Fuel Vehicle (AFV) Acquisition Requirements on Delicious Rank Alternative Fuels Data Center: State Hybrid Electric (HEV) Alternative Fuel Vehicle (AFV) Acquisition Requirements on Digg

396

Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Hybrid  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Hybrid Electric Vehicle (HEV) Acquisition Requirements to Hybrid Electric Vehicle (HEV) Acquisition Requirements to someone by E-mail Share Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Hybrid Electric Vehicle (HEV) Acquisition Requirements on Facebook Tweet about Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Hybrid Electric Vehicle (HEV) Acquisition Requirements on Twitter Bookmark Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Hybrid Electric Vehicle (HEV) Acquisition Requirements on Google Bookmark Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Hybrid Electric Vehicle (HEV) Acquisition Requirements on Delicious Rank Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Hybrid Electric Vehicle (HEV) Acquisition Requirements on Digg

397

Alternative Fuels Data Center: Hybrid Electric Vehicle (HEV) and Electric  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Hybrid Electric Hybrid Electric Vehicle (HEV) and Electric Vehicle (EV) Exemption from Vehicle Testing Requirements to someone by E-mail Share Alternative Fuels Data Center: Hybrid Electric Vehicle (HEV) and Electric Vehicle (EV) Exemption from Vehicle Testing Requirements on Facebook Tweet about Alternative Fuels Data Center: Hybrid Electric Vehicle (HEV) and Electric Vehicle (EV) Exemption from Vehicle Testing Requirements on Twitter Bookmark Alternative Fuels Data Center: Hybrid Electric Vehicle (HEV) and Electric Vehicle (EV) Exemption from Vehicle Testing Requirements on Google Bookmark Alternative Fuels Data Center: Hybrid Electric Vehicle (HEV) and Electric Vehicle (EV) Exemption from Vehicle Testing Requirements on Delicious Rank Alternative Fuels Data Center: Hybrid Electric Vehicle (HEV)

398

Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Hybrid  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

and Hybrid Electric Vehicle (HEV) Acquisition Requirements to and Hybrid Electric Vehicle (HEV) Acquisition Requirements to someone by E-mail Share Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Hybrid Electric Vehicle (HEV) Acquisition Requirements on Facebook Tweet about Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Hybrid Electric Vehicle (HEV) Acquisition Requirements on Twitter Bookmark Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Hybrid Electric Vehicle (HEV) Acquisition Requirements on Google Bookmark Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Hybrid Electric Vehicle (HEV) Acquisition Requirements on Delicious Rank Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Hybrid Electric Vehicle (HEV) Acquisition Requirements on Digg

399

Alternative Fuels Data Center: Texas Taxis Go Hybrid  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Texas Taxis Go Hybrid Texas Taxis Go Hybrid to someone by E-mail Share Alternative Fuels Data Center: Texas Taxis Go Hybrid on Facebook Tweet about Alternative Fuels Data Center: Texas Taxis Go Hybrid on Twitter Bookmark Alternative Fuels Data Center: Texas Taxis Go Hybrid on Google Bookmark Alternative Fuels Data Center: Texas Taxis Go Hybrid on Delicious Rank Alternative Fuels Data Center: Texas Taxis Go Hybrid on Digg Find More places to share Alternative Fuels Data Center: Texas Taxis Go Hybrid on AddThis.com... May 6, 2010 Texas Taxis Go Hybrid L earn how San Antonio is replacing traditional cabs with gasoline-electric hybrids. For information about this project, contact Alamo Area Clean Cities (San Antonio). Download QuickTime Video QuickTime (.mov) Download Windows Media Video Windows Media (.wmv)

400

Alternative Fuels Data Center: Hybrid Electric Horsepower for Kentucky  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Hybrid Electric Hybrid Electric Horsepower for Kentucky Schools to someone by E-mail Share Alternative Fuels Data Center: Hybrid Electric Horsepower for Kentucky Schools on Facebook Tweet about Alternative Fuels Data Center: Hybrid Electric Horsepower for Kentucky Schools on Twitter Bookmark Alternative Fuels Data Center: Hybrid Electric Horsepower for Kentucky Schools on Google Bookmark Alternative Fuels Data Center: Hybrid Electric Horsepower for Kentucky Schools on Delicious Rank Alternative Fuels Data Center: Hybrid Electric Horsepower for Kentucky Schools on Digg Find More places to share Alternative Fuels Data Center: Hybrid Electric Horsepower for Kentucky Schools on AddThis.com... April 7, 2011 Hybrid Electric Horsepower for Kentucky Schools " The hybrid school bus project not only serves as a means to improve

Note: This page contains sample records for the topic "hybrid tractor evaluation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Global Grid-Connected Hybrid-Electric Vehicle Project: Year-End Summary Report, November 2000  

Science Conference Proceedings (OSTI)

This interim report summarizes research conducted under the auspices of the Global Grid-Connected Hybrid Electric Vehicle Project, an EPRI initiative to promote the use of grid-connected electric technologies in heavy-duty applications. One study in the program evaluated the potential of converting a Ford E-350 or E-450 Super Duty chassis into a grid-connected hybrid electric vehicle airport shuttle bus and a Ford Explorer chassis into a dedicated electric vehicle delivery van. A second study analyzed ad...

2000-12-13T23:59:59.000Z

402

Demonstration Development Project: Solar-Fossil Hybrid Power Plants: Summary Report on Conceptual Designs  

Science Conference Proceedings (OSTI)

This document provides a high-level summary of selected EPRI research into solar-fossil hybrid power systems. It summarizes key technology results from a series of conceptual design studies that evaluated the performance of a range of solar-fossil hybrid options for existing natural gas combined cycle (NGCC) and coal-fired plants. All of the conceptual designs considered the use of solar-derived steam in conventional fossil-fired steam cycles, an approach that offsets some of the fuel required to generat...

2010-12-17T23:59:59.000Z

403

NOT EVERY HYBRID BECOMES ANOT EVERY HYBRID BECOMES A PRIUS: THE CASE AGAINST THEPRIUS: THE CASE AGAINST THE  

E-Print Network (OSTI)

NOT EVERY HYBRID BECOMES ANOT EVERY HYBRID BECOMES A PRIUS: THE CASE AGAINST THEPRIUS: THE CASE INTRODUCED ITS HYBRIDIN 1997 TOYOTA INTRODUCED ITS HYBRID CAR CALLED THE PRIUS WITH ELECTRICCAR CALLED THE PRIUS WITH ELECTRIC DRIVEDRIVE #12;IN THE 1950s FORD PROPOSED ITS HYBRID CARIN THE 1950s FORD PROPOSED

404

High Energy Batteries for Hybrid Buses  

DOE Green Energy (OSTI)

EnerDel batteries have already been employed successfully for electric vehicle (EV) applications. Compared to EV applications, hybrid electric vehicle (HEV) bus applications may be less stressful, but are still quite demanding, especially compared to battery applications for consumer products. This program evaluated EnerDel cell and pack system technologies with three different chemistries using real world HEV-Bus drive cycles recorded in three markets covering cold, hot, and mild climates. Cells were designed, developed, and fabricated using each of the following three chemistries: (1) Lithium nickel manganese cobalt oxide (NMC) - hard carbon (HC); (2) Lithium manganese oxide (LMO) - HC; and (3) LMO - lithium titanium oxide (LTO) cells. For each cell chemistry, battery pack systems integrated with an EnerDel battery management system (BMS) were successfully constructed with the following features: real time current monitoring, cell and pack voltage monitoring, cell and pack temperature monitoring, pack state of charge (SOC) reporting, cell balancing, and over voltage protection. These features are all necessary functions for real-world HEV-Bus applications. Drive cycle test data was collected for each of the three cell chemistries using real world drive profiles under hot, mild, and cold climate conditions representing cities like Houston, Seattle, and Minneapolis, respectively. We successfully tested the battery packs using real-world HEV-Bus drive profiles under these various climate conditions. The NMC-HC and LMO-HC based packs successfully completed the drive cycles, while the LMO-LTO based pack did not finish the preliminary testing for the drive cycles. It was concluded that the LMO-HC chemistry is optimal for the hot or mild climates, while the NMC-HC chemistry is optimal for the cold climate. In summary, the objectives were successfully accomplished at the conclusion of the project. This program provided technical data to DOE and the public for assessing EnerDel technology, and helps DOE to evaluate the merits of underlying technology. The successful completion of this program demonstrated the capability of EnerDel battery packs to satisfactorily supply all power and energy requirements of a real-world HEV-Bus drive profile. This program supports green solutions to metropolitan public transportation problems by demonstrating the effectiveness of EnerDel lithium ion batteries for HEV-Bus applications.

Bruce Lu

2010-12-31T23:59:59.000Z

405

Symmetric and asymmetric hybridization in citrus spp.  

E-Print Network (OSTI)

The United States is the second largest producer of oranges and grapefruit. However, the US citrus industry experiences constraints in production due to pests, diseases and environmental concerns. Furthermore, due to the low diversity in current commercial scion cultivars any exotic diseases, if introduced into any of the producing states could be devastating. To maintain the US industry competitiveness it is necessary to improve cold, pest and disease resistance to allow expansion of citrus production areas in the US, and to improve fruit quality characteristics such as sweetness, vitamins and phytochemical contents and seedlessness. Sexual hybridization in most Citrus species is complicated because they are highly apomictic. Polyembryony makes it difficult to create large segregating populations for selection. Somatic hybridization by protoplast fusion circumvents sexual incompatibilities and is a powerful tool in genetic improvement. Symmetric and asymmetric hybdridization (gamma irradiation plus iodoacetamide) via protoplast fusion were performed with the objective of producing somatic hybrids of Citrus paradisi with C. sinensis and C. reticulata with C. sinensis. These hybrids could be used for grapefruit improvement and to create genetic diversity. Furthermore, irradiated Swinglea glutinosa microprotoplasts were fused with ‘Ruby Red’ grapefruit and ‘Mucott’ tangor to assess the possibility of introgression of pieces of S. glutinosa chromosomes into the recipient protoplasts, a possible first step for radiation hybrid mapping. Double-inactivated fusions (irradiation + iodoacetamide) produced tetraploid and aneuploid plants, and hybridity was confirmed by amplified fragment length polymorphism (AFLP) analysis. This is the first report of obtaining rooted Citrus asymmetric hybrid plants, produced by irradiation plus iodoacetamide. AFLP confirmed presence of S. glutinosa into the receptor genomes, showing a possible donor introgression.

Bona, Claudine M.

2007-05-01T23:59:59.000Z

406

NETL - Post-Combustion CO2 Emissions Control - Evaluation of...  

NLE Websites -- All DOE Office Websites (Extended Search)

Evaluation of CO2 Capture from Existing Coal-Fired Plants by Hybrid Sorption Using Solid Sorbents (CACHYS(tm)) Project No.: DE-FE0007603 The University of North Dakota (UND) is...

407

HybridStore: A Cost-Efficient, High-Performance Storage System Combining SSDs and HDDs  

SciTech Connect

Unlike the use of DRAM for caching or buffering, certain idiosyncrasies of NAND Flash-based solid-state drives (SSDs) make their integration into existing systems non-trivial. Flash memory suffers from limits on its reliability, is an order of magnitude more expensive than the magnetic hard disk drives (HDDs), and can sometimes be as slow as the HDD (due to excessive garbage collection (GC) induced by high intensity of random writes). Given these trade-offs between HDDs and SSDs in terms of cost, performance, and lifetime, the current consensus among several storage experts is to view SSDs not as a replacement for HDD but rather as a complementary device within the high-performance storage hierarchy. We design and evaluate such a hybrid system called HybridStore to provide: (a) HybridPlan: improved capacity planning technique to administrators with the overall goal of operating within cost-budgets and (b) HybridDyn: improved performance/lifetime guarantees during episodes of deviations from expected workloads through two novel mechanisms: write-regulation and fragmentation busting. As an illustrative example of HybridStore s ef cacy, HybridPlan is able to nd the most cost-effective storage con guration for a large scale workload of Microsoft Research and suggest one MLC SSD with ten 7.2K RPM HDDs instead of fourteen 7.2K RPM HDDs only. HybridDyn is able to reduce the average response time for an enterprise scale random-write dominant workload by about 71% as compared to a HDD-based system.

Kim, Youngjae [ORNL; Gupta, Aayush [Pennsylvania State University, University Park, PA; Urgaonkar, Bhuvan [Pennsylvania State University; Piotr, Berman [Pennsylvania State University, University Park, PA; Sivasubramaniam, Anand [Pennsylvania State University

2011-01-01T23:59:59.000Z

408

Electric and Hybrid Vehicle System Research and Development Project: Hybrid Vehicle Potential Assessment. Volume 1. Summary  

DOE Green Energy (OSTI)

The results of investigations conducted under Ce Hybrid Vehicle Potential Assessment Task are reported in 10 volumes. This volume contains an overview of the study and its results. The purpose of the overall study was to determine if the petroleum fuel savings achievable through the use of hybrid electric vehicles is worth the R and D expenditures needed to develop the hybrid vehicles and to determine R and D priorities. It was concluded that by the year 2010 hybrid vehicles could replace 80% of the automotive power that would otherwise be produced from petroleum fuels; the public should not suffer any mobility loss through the use of hybrid vehicles; high initial and life-cycle costs are a limiting factor; and R and D funds should be spent for systems design and the development of low-cost batteries and controllers. (LCL)

Surber, F.T.

1979-09-30T23:59:59.000Z

409

Assessing the Battery Cost at Which Plug-In Hybrid Medium-Duty Parcel Delivery Vehicles Become Cost-Effective  

DOE Green Energy (OSTI)

The National Renewable Energy Laboratory (NREL) validated diesel-conventional and diesel-hybrid medium-duty parcel delivery vehicle models to evaluate petroleum reductions and cost implications of hybrid and plug-in hybrid diesel variants. The hybrid and plug-in hybrid variants are run on a field data-derived design matrix to analyze the effect of drive cycle, distance, engine downsizing, battery replacements, and battery energy on fuel consumption and lifetime cost. For an array of diesel fuel costs, the battery cost per kilowatt-hour at which the hybridized configuration becomes cost-effective is calculated. This builds on a previous analysis that found the fuel savings from medium duty plug-in hybrids more than offset the vehicles' incremental price under future battery and fuel cost projections, but that they seldom did so under present day cost assumptions in the absence of purchase incentives. The results also highlight the importance of understanding the application's drive cycle specific daily distance and kinetic intensity.

Ramroth, L. A.; Gonder, J. D.; Brooker, A. D.

2013-04-01T23:59:59.000Z

410

Analysis of hybrid solar systems  

DOE Green Energy (OSTI)

This study uses the TRNSYS simulation program to evaluate the performance of active charge/passive discharge solar systems with water as the working fluid. This design was introduced in the Village Homes development in Davis, Calif., and is currently being used by Trident Energy Systems in Davis. TRNSYS simulations are used to evaluate the heating performance and cooling augmentation provided by systems in several climates. The results of the simulations are used to develop a simplified analysis tool similar to the F-chart and Phi-bar procedures used for active systems. This tool, currently in a preliminary stage, should provide the designer with quantitative performance estimates for comparison with other passive, active, and nonsolar heating and cooling designs.

Swisher, J.

1980-10-01T23:59:59.000Z

411

Hybrid staging of geothermal energy conversion processes  

SciTech Connect

A hybrid system consists of two or more energy conversion processes. This study examines the use of three energy conversion machines in hybrid systems: the conventional single-phase turbine, and the two-phase expanders known as the Lysholm engine and the radial outflow reaction turbine. Two hybrid systems are presented. The first is a two-stage, single-flash system with the Lysholm engine as the first stage, and a separator and conventional turbine as the second stage. The second system adds a radial outflow reaction turbine to recover a part of the energy rejected in the second stage. A theoretical specific power of 41.3 kW.s/lb is predicted for the two-stage, single-flash hybrid system. The addition of the radial outflow rotary turbine increases performance to 44.8 kW.s/lb. Both are superior to the double-flash system, with a specific power of 37.8 kW.s/lb. In addition, the hybrid system offers operating flexibility.

Steidel, R.F.

1978-09-01T23:59:59.000Z

412

Manzanita Hybrid Power system Project Final Report  

DOE Green Energy (OSTI)

The Manzanita Indian Reservation is located in southeastern San Diego County, California. The Tribe has long recognized that the Reservation has an abundant wind resource that could be commercially utilized to its benefit, and in 1995 the Tribe established the Manzanita Renewable Energy Office. Through the U.S. Department of Energy's Tribal Energy Program the Band received funds to install a hybrid renewable power system to provide electricity to one of the tribal community buildings, the Manzanita Activities Center (MAC building). The project began September 30, 1999 and was completed March 31, 2005. The system was designed and the equipment supplied by Northern Power Systems, Inc, an engineering company with expertise in renewable hybrid system design and development. Personnel of the National Renewable Energy Laboratory provided technical assistance in system design, and continued to provide technical assistance in system monitoring. The grid-connected renewable hybrid wind/photovoltaic system provides a demonstration of a solar/wind energy hybrid power-generating project on Manzanita Tribal land. During the system design phase, the National Renewable Energy Lab estimated that the wind turbine is expected to produce 10,000-kilowatt hours per year and the solar array 2,000-kilowatt hours per year. The hybrid system was designed to provide approximately 80 percent of the electricity used annually in the MAC building. The project proposed to demonstrate that this kind of a system design would provide highly reliable renewable power for community uses.

Trisha Frank

2005-03-31T23:59:59.000Z

413

Fuel Economy of Hybrids, Diesels, and Alternative Fuel Vehicles  

NLE Websites -- All DOE Office Websites (Extended Search)

You are here: Find a Car - Home > Hybrids, Diesels, and Alternative Fuel You are here: Find a Car - Home > Hybrids, Diesels, and Alternative Fuel Vehicles Hybrids, Diesels, and Alternative Fuel Vehicles Search by Vehicle Type 2014 2013 2012 2011 2010 2009 2008 2007 2006 2005 2004 2003 2002 2001 2000 Select Vehicle Type Diesel Electric Ethanol-Gasoline Hybrid Plug-in Hybrid Natural Gas Bifuel Natural Gas Bifuel Propane Go More Search Options Browse New Cars Hybrid Vehicles Plug-in Hybrid Vehicles Battery Electric Vehicles Diesel Vehicles Flex-Fuel Vehicles CNG Vehicles Related Information How Hybrid Vehicles Work How Fuel Cell Vehicles Work MotorWeek Videos Compare Hybrids Compare Diesels Extreme MPG Tax Incentive Information Center Alternative Fuel Station Locator Alternative Fuel and Advanced Vehicle Data Center | Share I want to... Compare Side-by-Side

414

Vehicle Technologies Office: Materials for Hybrid and Electric Drive  

NLE Websites -- All DOE Office Websites (Extended Search)

for Hybrid and for Hybrid and Electric Drive Systems to someone by E-mail Share Vehicle Technologies Office: Materials for Hybrid and Electric Drive Systems on Facebook Tweet about Vehicle Technologies Office: Materials for Hybrid and Electric Drive Systems on Twitter Bookmark Vehicle Technologies Office: Materials for Hybrid and Electric Drive Systems on Google Bookmark Vehicle Technologies Office: Materials for Hybrid and Electric Drive Systems on Delicious Rank Vehicle Technologies Office: Materials for Hybrid and Electric Drive Systems on Digg Find More places to share Vehicle Technologies Office: Materials for Hybrid and Electric Drive Systems on AddThis.com... Just the Basics Hybrid & Vehicle Systems Energy Storage Advanced Power Electronics & Electrical Machines

415

Alternative Fuels Data Center: Plug-In Hybrid Electric Vehicles  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Plug-In Hybrid Plug-In Hybrid Electric Vehicles to someone by E-mail Share Alternative Fuels Data Center: Plug-In Hybrid Electric Vehicles on Facebook Tweet about Alternative Fuels Data Center: Plug-In Hybrid Electric Vehicles on Twitter Bookmark Alternative Fuels Data Center: Plug-In Hybrid Electric Vehicles on Google Bookmark Alternative Fuels Data Center: Plug-In Hybrid Electric Vehicles on Delicious Rank Alternative Fuels Data Center: Plug-In Hybrid Electric Vehicles on Digg Find More places to share Alternative Fuels Data Center: Plug-In Hybrid Electric Vehicles on AddThis.com... More in this section... Electricity Basics Benefits & Considerations Stations Vehicles Availability Conversions Emissions Batteries Deployment Maintenance & Safety Laws & Incentives Hybrids

416

Series hybrid vehicles and optimized hydrogen engine design  

DOE Green Energy (OSTI)

Lawrence Livermore, Sandia Livermore and Los Alamos National Laboratories have a joint project to develop an optimized hydrogen fueled engine for series hybrid automobiles. The major divisions of responsibility are: system analysis, engine design and kinetics modeling by LLNL; performance and emission testing, and friction reduction by SNL; computational fluid mechanics and combustion modeling by LANL. This project is a component of the Department of Energy, Office of Utility Technology, National Hydrogen Program. We report here on the progress on system analysis and preliminary engine testing. We have done system studies of series hybrid automobiles that approach the PNGV design goal of 34 km/liter (80 mpg), for 384 km (240 mi) and 608 km (380 mi) ranges. Our results indicate that such a vehicle appears feasible using an optimized hydrogen engine. The impact of various on-board storage options on fuel economy are evaluated. Experiments with an available engine at the Sandia Combustion Research Facility demonstrated NO{sub x} emissions of 10 to 20 ppm at an equivalence ratio of 0.4, rising to about 500 ppm at 0.5 equivalence ratio using neat hydrogen. Hybrid vehicle simulation studies indicate that exhaust NO{sub x} concentrations must be less than 180 ppm to meet the 0.2 g/mile California Air Resources Board ULEV or Federal Tier II emissions regulations. We have designed and fabricated a first generation optimized hydrogen engine head for use on an existing single cylinder Onan engine. This head currently features 14.8:1 compression ratio, dual ignition, water cooling, two valves and open quiescent combustion chamber to minimize heat transfer losses.

Smith, J.R.; Aceves, S. [Lawrence Livermore National Lab., CA (United States); Van Blarigan, P. [Sandia National Labs., Livermore, CA (United States)

1995-05-10T23:59:59.000Z

417

Measured Laboratory and In-Use Fuel Economy Observed over Targeted Drive Cycles for Comparable Hybrid and Conventional Package Delivery Vehicles  

Science Conference Proceedings (OSTI)

In-use and laboratory-derived fuel economies were analyzed for a medium-duty hybrid electric drivetrain with 'engine off at idle' capability and a conventional drivetrain in a typical commercial package delivery application. Vehicles studied included eleven 2010 Freightliner P100H hybrids in service at a United Parcel Service facility in Minneapolis during the first half of 2010. The hybrids were evaluated for 18 months against eleven 2010 Freightliner P100D diesels at the same facility. Both vehicle groups use the same 2009 Cummins ISB 200-HP engine. In-use fuel economy was evaluated using UPS's fueling and mileage records, periodic ECM image downloads, and J1939 CAN bus recordings during the periods of duty cycle study. Analysis of the in-use fuel economy showed 13%-29% hybrid advantage depending on measurement method, and a delivery route assignment analysis showed 13%-26% hybrid advantage on the less kinetically intense original diesel route assignments and 20%-33% hybrid advantage on the more kinetically intense original hybrid route assignments. Three standardized laboratory drive cycles were selected that encompassed the range of real-world in-use data. The hybrid vehicle demonstrated improvements in ton-mi./gal fuel economy of 39%, 45%, and 21% on the NYC Comp, HTUF Class 4, and CARB HHDDT test cycles, respectively.

Lammert, M. P.; Walkowicz, K.; Duran, A.; Sindler, P.

2012-10-01T23:59:59.000Z

418

Effect of design parameter variations on hybrid (combination hydrostatic and hydrodynamic) bearings for use in high speed turbomachinery  

E-Print Network (OSTI)

Hybrid (combination hydrostatic and hydrodynamic) bearings have been proposed for use as a support element in cryogenic high speed turbomachinery for primary and auxiliary space power applications because of their long lifetime, low friction and wear, and ability to use low viscosity fluids. However, very little work has been done in determining the rotordynamic performance of hybrid journal bearings. This thesis presents theoretical and experimental results for radial-injection, orifice-compensated, annulus-fed hybrid water journal bearings which show the effects on bearing performance of changing the following design parameters: radial clearance, concentric recess pressure ratio, recess-to-land area ratio, and recess depth geometry. Experimental test results are used to evaluate predictions from the analytical hybrid bearing computer model developed by San Andres (1990).

Mosher, Phillip Andrew

1993-01-01T23:59:59.000Z

419

Verified hybrid controllers for automated vehicles  

E-Print Network (OSTI)

Abstract — The objective of an Automated Highway System (AHS) is to increase the safety and throughput of the existing highway infrastructure by introducing traffic automation. AHS is an example of a large scale, multiagent complex dynamical system and is ideally suited for a hierarchical hybrid controller. We discuss the design of safe and efficient hybrid controllers for regulation of vehicles on an AHS. We use game theoretic techniques to deal with the multiagent and multiobjective nature of the problem. The result is a hybrid controller that by design guarantees safety, without the need for further verification. The calculations also provide an upper bound on the performance that can be expected in terms of throughput at various levels of centralization. Index Terms — Automated highway systems, game theory, safety. I.

John Lygeros; Datta N. Godbole; Shankar Sastry

1998-01-01T23:59:59.000Z

420

Combining stated and revealed choice research to simulate the neighbor effect: The case of hybrid-electric vehicles  

E-Print Network (OSTI)

D R.L. Polk & Co. , 2006. Hybrid Vehicle Registrations Morecapital cost of the hybrid vehicle, subsidy providedfor the hybrid vehicle, horsepower of the hybrid vehicle,

Axsen, Jonn; Mountain, Dean C.; Jaccard, Mark

2009-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "hybrid tractor evaluation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Hybrid  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Fuel Fuel Vehicle (AFV) and Hybrid Electric Vehicle (HEV) Funding to someone by E-mail Share Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Hybrid Electric Vehicle (HEV) Funding on Facebook Tweet about Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Hybrid Electric Vehicle (HEV) Funding on Twitter Bookmark Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Hybrid Electric Vehicle (HEV) Funding on Google Bookmark Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Hybrid Electric Vehicle (HEV) Funding on Delicious Rank Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Hybrid Electric Vehicle (HEV) Funding on Digg Find More places to share Alternative Fuels Data Center: Alternative

422

Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Hybrid  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Alternative Fuel Alternative Fuel Vehicle (AFV) and Hybrid Electric Vehicle (HEV) Insurance Discount to someone by E-mail Share Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Hybrid Electric Vehicle (HEV) Insurance Discount on Facebook Tweet about Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Hybrid Electric Vehicle (HEV) Insurance Discount on Twitter Bookmark Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Hybrid Electric Vehicle (HEV) Insurance Discount on Google Bookmark Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Hybrid Electric Vehicle (HEV) Insurance Discount on Delicious Rank Alternative Fuels Data Center: Alternative Fuel Vehicle (AFV) and Hybrid Electric Vehicle (HEV) Insurance Discount on Digg

423

Genetic and Environmental Effects on Phenolic Composition and Agronomic Performacne in Black Sorghum (Sorghum bicolor L.) Hybrids  

E-Print Network (OSTI)

A healthy diet requires a shift from the consumption of highly refined and processed foods with low nutritional value and towards whole grain food that have increased levels of antioxidants and phenolic compounds. Certain specialty sorghum genotypes have been identified as potential whole grain foods that have high levels of desired chemical compounds. Specifically, sorghums with a black pericarp are excellent sources of antioxidant compounds, including the unique compound 3-deoxyanthocyanin (3-DOA). Although extensive work has been performed on the chemistry and food properties of black sorghum inbreds, little research has been done studying the grain phenolic composition and agronomic performance of black sorghum hybrids in production environments. The goal of this study was to evaluate black sorghum hybrids with differing genetic backgrounds for grain phenolic composition and agronomic performance across multiple environments and identify the best lines for producing these hybrids. Results from this study confirm that sorghums with a black pericarp contain elevated levels of phenols, tannins and 3-DOA. Concentrations of these beneficial compounds were many times the concentration levels seen in traditional grain hybrids. Grain yields of black sorghum hybrids averaged 36% below commercial hybrids in this study. Lower grain yields could be due to reduced heterosis in black sorghum hybrids and other unknown factors associated with the black phenotype. From this study, the Texas AgriLife Sorghum Breeding Program has developed two elite black sorghum lines for release as the first publicly available black pericarp seed parents. These newly developed seed parents, proposed for release as Tx3363 and Tx3364, allow for the creation of the first temperately adapted black seeded grain hybrid. These hybrids help address the growing demand for products that are healthy, and provide natural and stable antioxidant compounds for a growing health food industry.

Hayes, Chad

2012-12-01T23:59:59.000Z

424

Microgravity-Hybrid Microgravity | Open Energy Information  

Open Energy Info (EERE)

Page Page Edit with form History Facebook icon Twitter icon » Microgravity-Hybrid Microgravity Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Technique: Microgravity-Hybrid Microgravity Details Activities (0) Areas (0) Regions (0) NEPA(1) Exploration Technique Information Exploration Group: Geophysical Techniques Exploration Sub Group: Gravity Techniques Parent Exploration Technique: Gravity Techniques Information Provided by Technique Lithology: Stratigraphic/Structural: Ground subsidence can be mapped using microgravity Hydrological: Monitoring net mass changes of a geothermal reservoir due to production and reinjection processes Thermal: Changes in liquid density due to temperature changes in the reservoir Cost Information Low-End Estimate (USD): 50.005,000 centUSD

425

Lower Hybrid to Whistler Wave Conversion  

Science Conference Proceedings (OSTI)

In this presentation we discuss recent work concerning the conversion of whistler waves to lower hybrid waves (as well as the inverse process). These efforts have been motivated by the issue of attenuation of upward propagating whistler waves in the ionosphere generated by VLF transmitters on the ground, i.e., the 'Starks 20 db' problem, which affects the lifetimes of energetic electrons trapped in the geomagnetic field at low magnetic altitude (L). We discuss recent fluid and kinetic plasma simulations as well as ongoing experiments at UCLA to quantify linear and nonlinear mode conversion of lower hybrid to whistler waves.

Winske, Dan [Los Alamos National Laboratory

2012-07-16T23:59:59.000Z

426

The Rational Hybrid Monte Carlo Algorithm  

E-Print Network (OSTI)

The past few years have seen considerable progress in algorithmic development for the generation of gauge fields including the effects of dynamical fermions. The Rational Hybrid Monte Carlo (RHMC) algorithm, where Hybrid Monte Carlo is performed using a rational approximation in place the usual inverse quark matrix kernel is one of these developments. This algorithm has been found to be extremely beneficial in many areas of lattice QCD (chiral fermions, finite temperature, Wilson fermions etc.). We review the algorithm and some of these benefits, and we compare against other recent algorithm developements. We conclude with an update of the Berlin wall plot comparing costs of all popular fermion formulations.

M. A. Clark

2006-10-06T23:59:59.000Z

427

Italian hybrid and fission reactors scenario analysis  

SciTech Connect

Italy is a country where a long tradition of studies both in the fission and fusion field is consolidated; nevertheless a strong public opinion concerned with the destination of the Spent Nuclear Fuel hinders the development of nuclear power. The possibility to a severe reduction of the NSF mass generated from a fleet of nuclear reactors employing an hypothetical fusionfission hybrid reactor has been investigated in the Italian framework. The possibility to produce nuclear fuel for the fission nuclear reactors with the hybrid reactor was analyzed too.

Ciotti, M.; Manzano, J.; Sepielli, M. [ENEA CR Frascati, Via Enrico Fermi, 45, 00044, Frascati, Roma (Italy); ENEA CR casaccia, Via Anguillarese, 301, 00123, Santa Maria di Galeria, Roma (Italy)

2012-06-19T23:59:59.000Z

428

Assessment of the Greenhouse Gas Emission Reduction Potential of Ultra-Clean Hybrid-Electric Vehicles  

E-Print Network (OSTI)

Table ES-3: Summaryof Hybrid Vehicle Fuel Economy Results onmal ICE and Series Hybrid Vehicles (t) Vehicle Test Weight (I) Conventional and Series Hybrid Vehicles had same weight,

Burke, A.F.; Miller, M.

1997-01-01T23:59:59.000Z

429

Electrochemical Capacitors as Energy Storage in Hybrid-Electric Vehicles: Present Status and Future Prospects  

E-Print Network (OSTI)

ultracapacitors, fuel cells and hybrid vehicle design. Dr.on electric and hybrid vehicle technology and applicationssupervises testing in the Hybrid Vehicle Propulsion Systems

Burke, Andy; Miller, Marshall

2009-01-01T23:59:59.000Z

430

Anticipating plug-in hybrid vehicle energy impacts in California: Constructing consumer-informed recharge profiles  

E-Print Network (OSTI)

converted plug-in hybrid vehicles. Transportation ResearchM. , 2006. Plug-In Hybrid Vehicle Analysis. Nationalgas emissions from plug-in hybrid vehicles: implications for

Axsen, Jonn; Kurani, Kenneth S

2010-01-01T23:59:59.000Z

431

Performance Characteristics of Lithium-ion Batteries of Various Chemistries for Plug-in Hybrid Vehicles  

E-Print Network (OSTI)

supervises testing in the Hybrid Vehicle Propulsion SystemsChemistries for Plug-in Hybrid Vehicles Andrew Burke,batteries, plug-in hybrid vehicles, energy density, pulse

Burke, Andrew; Miller, Marshall

2009-01-01T23:59:59.000Z

432

Testing Electric Vehicle Demand in "Hybrid Households" Using a Reflexive Survey  

E-Print Network (OSTI)

In contrast to a hybrid vehicle whichcombines multiple1994) "Demand Electric Vehicles in Hybrid for Households:or 180 mile hybrid electric vehicle. Natural gas vehicles (

Kurani, Kenneth S.; Turrentine, Thomas; Sperling, Daniel

2001-01-01T23:59:59.000Z

433

Semiotics and Advanced Vehicles: What Hybrid Electric Vehicles (HEVs) Mean and Why it Matters to Consumers  

E-Print Network (OSTI)

Automobile (2007) Future Toyota Hybrids: Prius Times Three.features/news/0706_future_toyota_hybrids/ Automotive News742. Freeman, S. (2003) “Toyota's Prius Hybrid Named Motor

Heffner, Reid R.

2007-01-01T23:59:59.000Z

434

Failure modes in high-power lithium-ion batteries for use in hybrid electric vehicles  

E-Print Network (OSTI)

BATTERIES FOR USE IN HYBRID ELECTRIC VEHICLES R. Kostecki,ion batteries for hybrid electric vehicles. Nine 18650-sizebatteries for hybrid electric vehicle (HEV) applications.

2001-01-01T23:59:59.000Z

435

Semiotics and Advanced Vehicles: What Hybrid Electric Vehicles (HEVs) Mean and Why it Matters to Consumers  

E-Print Network (OSTI)

In Early Markets For Hybrid Electric Vehicles. Institute ofon Plug-in Hybrid Electric Vehicle (PHEV) Technology,and Impacts of Hybrid Electric Vehicle Options. Electric

Heffner, Reid R.

2007-01-01T23:59:59.000Z

436

Anticipating plug-in hybrid vehicle energy impacts in California: Constructing consumer-informed recharge profiles  

E-Print Network (OSTI)

of Plug-In Hybrid Electric Vehicles, vol. 1. Nationwidecompetitive plug-in hybrid electric vehicles. EnvironmentalDriving plug-in hybrid electric vehicles: reports from US

Axsen, Jonn; Kurani, Kenneth S

2010-01-01T23:59:59.000Z

437

HYBRID2 -- A versatile model of the performance of hybrid power systems  

DOE Green Energy (OSTI)

In 1993, the National Renewable Laboratory (NREL) made an assessment of the available tools from the United States and Europe for predicting the long-term performance of hybrid power systems. By hybrid power the authors mean combinations of two or more power sources wind turbines, photovoltaics (PV), diesel gensets, or other generators into integrated systems for electric power generation in remote locations. Their conclusion was that there was no single, user-friendly tool capable of modeling the full range of hybrid power technologies being considered for the 1990s and beyond. The existing tools were, in particular, lacking flexibility in system configuration and in dispatch of components. As a result, NREL developed a specification for a model, called HYBRID2, for making comparisons of competing technology options on a level playing field. This specification was prepared with a range of potential users in mind including not only the US Department of Energy (DOE) renewable energy programs, but also the US wind industry, technical consultants, international development institutions/banks, and rural electrification programs in developing countries. During 1994, NREL and subcontractor, the University of Massachusetts (UMass), began development of HYBRID2 with funding from the DOE Wind Energy Program. It builds on the wind/diesel model, HYBRID1, developed previously by UMass, and expands that model to accommodate the wider array of technologies used in hybrid power systems. This paper will provide an overview of the model`s features, functions, and status.

Green, H.J. [National Renewable Energy Lab., Golden, CO (United States); Manwell, J. [Univ. of Massachusetts, Amherst, MA (United States)

1995-04-01T23:59:59.000Z

438

Plug-In Hybrid Electric Vehicles - PHEV Modeling - Component Requirement  

NLE Websites -- All DOE Office Websites (Extended Search)

Requirement Definition for PHEVs Requirement Definition for PHEVs One of the main objectives of the U.S. Department of Energy's (DOE's) Plug-in Hybrid Electric Vehicle R&D Plan (2.2Mb pdf) is to "determine component development requirements" through simulation analysis. PSAT has been used to design and evaluate a series of PHEVs to define the requirements of different components, focusing on the energy storage system's power and energy. Several vehicle classes (including midsize car, crossover SUV and midsize SUV) and All Electric Range (AER from 10 to 40 miles) were considered. The preliminary simulations were performed at Argonne using a pre-transmission parallel hybrid configuration with an energy storage system sized to run the Urban Dynanometer Driving Schedule (UDDS) in electric mode. Additional powertrain configurations and sizing algorithm are currently being considered. Trade-off studies are being performed as ways to achieve some level of performance while easing requirements on one area or another. As shown in the figure below, the FreedomCAR Energy Storage Technical Team selected a short term and a long term All Electric Range (AER) goals based on several vehicle simulations.

439

The neutronics studies of fusion fission hybrid power reactor  

SciTech Connect

In this paper, a series of neutronics analysis of hybrid power reactor is proposed. The ideas of loading different fuels in a modular-type fission blanket is analyzed, fitting different level of fusion developments, i.e., the current experimental power output, the level can be obtained in the coming future and the high-power fusion reactor like ITER. The energy multiplication of fission blankets and tritium breeding ratio are evaluated as the criterion of design. The analysis is implemented based on the D-type simplified model, aiming to find a feasible 1000MWe hybrid power reactor for 5 years' lifetime. Three patterns are analyzed: 1) for the low fusion power, the reprocessed fuel is chosen. The fuel with high plutonium content is loaded to achieve large energy multiplication. 2) For the middle fusion power, the spent fuel from PWRs can be used to realize about 30 times energy multiplication. 3) For the high fusion power, the natural uranium can be directly used and about 10 times energy multiplication can be achieved.

Zheng Youqi; Wu Hongchun; Zu Tiejun; Yang Chao; Cao Liangzhi [School of Nuclear Science and Technology, Xi'an Jiaotong University, Xi'an, Shaanxi, 710049 (China)

2012-06-19T23:59:59.000Z

440

Commercial viability of hybrid vehicles : best household use and cross national considerations.  

DOE Green Energy (OSTI)

Japanese automakers have introduced hybrid passenger cars in Japan and will soon do so in the US. In this paper, we report how we used early computer simulation model results to compare the commercial viability of a hypothetical near-term (next decade) hybrid mid-size passenger car configuration under varying fuel price and driving patterns. The fuel prices and driving patterns evaluated are designed to span likely values for major OECD nations. Two types of models are used. One allows the ''design'' of a hybrid to a specified set of performance requirements and the prediction of fuel economy under a number of possible driving patterns (called driving cycles). Another provides an estimate of the incremental cost of the hybrid in comparison to a comparably performing conventional vehicle. In this paper, the models are applied to predict the NPV cost of conventional gasoline-fueled vehicles vs. parallel hybrid vehicles. The parallel hybrids are assumed to (1) be produced at high volume, (2) use nickel metal hydride battery packs, and (3) have high-strength steel bodies. The conventional vehicle also is assumed to have a high-strength steel body. The simulated vehicles are held constant in many respects, including 0-60 time, engine type, aerodynamic drag coefficient, tire rolling resistance, and frontal area. The hybrids analyzed use the minimum size battery pack and motor to meet specified 0-60 times. A key characteristic affecting commercial viability is noted and quantified: that hybrids achieve the most pronounced fuel economy increase (best use) in slow, average-speed, stop-and-go driving, but when households consistently drive these vehicles under these conditions, they tend to travel fewer miles than average vehicles. We find that hours driven is a more valuable measure than miles. Estimates are developed concerning hours of use of household vehicles versus driving cycle, and the pattern of minimum NPV incremental cost (or benefit) of selecting the hybrid over the conventional vehicle at various fuel prices is illustrated. These results are based on data from various OECD motions on fuel price, annual miles of travel per vehicle, and driving cycles assumed to be applicable in those nations. Scatter in results plotted as a function of average speed, related to details of driving cycles and the vehicles selected for analysis, is discussed.

Santini, D. J.; Vyas, A. D.

1999-07-16T23:59:59.000Z

Note: This page contains sample records for the topic "hybrid tractor evaluation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Electro jet drilling using hybrid NNGA approach  

Science Conference Proceedings (OSTI)

This paper presents a hybrid neural network and genetic algorithm (NNGA) approach for the multi-response optimization of the electro jet drilling (EJD) process. The approach first uses a neural network model to predict the response parameters of the ... Keywords: Electro jet drilling, Electrochemical machining, Genetic algorithm, Multi-response, Neural network, Optimization

Mohan Sen; H. S. Shan

2007-02-01T23:59:59.000Z

442

Dynamic power management with hybrid power sources  

Science Conference Proceedings (OSTI)

DPM (Dynamic Power Management) is an effective technique for reducing the energy consumption of embedded systems that is based on migrating to a low power state when possible. While conventional DPM minimizes the energy consumption of the embedded system, ... Keywords: DPM, embedded system, fuel cell, hybrid power

Jianli Zhuo; Chaitali Chakrabarti; Kyungsoo Lee; Naehyuck Chang

2007-06-01T23:59:59.000Z

443

Hybrid simulation models - When, Why, How?  

Science Conference Proceedings (OSTI)

Agent-Based Modeling and Simulation (ABMS) and System Dynamics (SD) are two popular simulation paradigms. Despite their common goal, these simulation methods are rarely combined and there has been a very low amount of joint research in these fields. ... Keywords: Agent-Based Modeling and Simulation, Artificial intelligence, Expert Systems, Hybrid simulation models, System Dynamics

Lauri Lättilä; Per Hilletofth; Bishan Lin

2010-12-01T23:59:59.000Z

444

Predicting time series with advanced hybrid systems  

Science Conference Proceedings (OSTI)

Autogressive moving average (ARMA) has been widely used to model processes that generate linear time-series. Recent research activities in forecasting with artificial neutral networks (ANNs) suggest that ANNs can be a promising alternative to the traditional ... Keywords: ARMA models, fuzzy system, hybrid system, neutral networks, time series

O. Valenzuela; I. Rojas; F. Rojas; H. Pomares; J. Gonzalez; L. J. Herrera; A. Guillen

2005-12-01T23:59:59.000Z

445

GlueX: Photoproduction of Hybrid Mesons  

SciTech Connect

The goal of the GlueX experiment is to provide critical data to help understand the soft gluonic field responsible for binding quarks in hadrons. Hybrid mesons, and in particular exotic hybrid mesons, provide the ideal laboratory for testing QCD in the confinement regime since these mesons explicitly manifest the gluonic degrees of freedom. Photoproduction is expected to be particularly effective in producing exotic hybrids but there is little data on the photoproduction of light mesons. GlueX will use the new 12-GeV electron beam to produce a 9-GeV beam of linearly polarized photons using the technique of coherent bremsstrahlung. A solenoid-based hermetic detector is under construction, which will be used to collect data on meson production and decays. These data will also be used to study the spectrum of conventional mesons, including the poorly understood excited vector mesons. This talk will describe the latest theoretical developments to help understand how the data of hybrid mesons can provide insights into the fundamental theory of strong interactions.

Elton Smith

2012-12-01T23:59:59.000Z

446

Top 10 tech cars [hybrid electric vehicles  

Science Conference Proceedings (OSTI)

A number of new hybrid electric vehicle owners have expressed their disappointment with their purchase because of poor mileage. Official ratings for fuel use, based on the outdated driving patterns of US government test, turned out to be a poor predictor ...

J. Voelcker

2005-03-01T23:59:59.000Z

447

A Hybrid Network Emergency Communication Model  

Science Conference Proceedings (OSTI)

To communicate within disaster scenarios, different devices/systems need to cooperate with specific protocols. The key communication protocol needs to provide interoperability among these systems and provide the solution for emergency services. The paper ... Keywords: Ad Hoc Network, Hybrid Network Emergency Communication Protocol HNEC, Inter-Domain Messaging IDM, Network Disaster Recovery, Routing Protocols, Sensor Network

Abdussalam Nuri Baryun, Khalid Al Begain, David Villa

2013-04-01T23:59:59.000Z

448

Associative computer: a hybrid connectionistic production system  

Science Conference Proceedings (OSTI)

In this paper, we introduce a connectionistic hybrid production system, which relies on the distributed representation and the usage of associative memories. Benefits of the distributed representation include heuristics resulting from pictogram representation. ... Keywords: Connectionism, Distributed representation, Learning, Problem solving, Production system

Andreas Wichert

2005-06-01T23:59:59.000Z

449

Hybrid Membranes for Light Gas Separations  

E-Print Network (OSTI)

Membrane separations provide a potentially attractive technology over conventional processes due to their advantages, such as low capital cost and energy consumption. The goal of this thesis is to design hybrid membranes that facilitate specific gas separations, especially olefin/paraffin separations. This thesis focuses on the designing dendrimer-based hybrid membranes on mesoporous alumina for reverse-selective separations, synthesizing Cu(I)-dendrimer hybrid membrane to facilitate olefin/paraffin separations, particularly ethylene/methane separation, and investigating the influence of solvent, stabilizing ligands on facilitated transport membrane. Reverse-selective gas separations have attracted considerable attention in removing the heavier/larger molecules from gas mixtures. In this study, dendrimer-based chemistry was proved to be an effective method by altering dendrimer structures and generations. G6-PIP, G4-AMP and G3-XDA are capable to fill the alumina mesopores and slight selectivity are observed. Facilitated transport membranes were made to increase the olefin/paraffin selectivity based on their chemical interaction with olefin molecules. Two approaches were explored, the first was to combine facilitator Cu(I) with dendrimer hybrid membrane to increase olefin permeance and olefin/paraffin selectivity simultaneously, and second was to facilitate transport membrane functionality by altering solvents and stabilizing ligands. Promising results were found by these two approaches, which were: 1) olefin/paraffin selectivity slightly increased by introducing facilitator Cu(I), 2) the interaction between Cu(I) and dendrimer functional groups are better known.

Liu, Ting

2012-05-01T23:59:59.000Z

450

Hybrid cache architecture with disparate memory technologies  

Science Conference Proceedings (OSTI)

Caching techniques have been an efficient mechanism for mitigating the effects of the processor-memory speed gap. Traditional multi-level SRAM-based cache hierarchies, especially in the context of chip multiprocessors (CMPs), present many challenges ... Keywords: hybrid cache architecture, three-dimensional ic

Xiaoxia Wu; Jian Li; Lixin Zhang; Evan Speight; Ram Rajamony; Yuan Xie

2009-06-01T23:59:59.000Z

451

Page placement in hybrid memory systems  

Science Conference Proceedings (OSTI)

Phase-Change Memory (PCM) technology has received substantial attention recently. Because PCM is byte-addressable and exhibits access times in the nanosecond range, it can be used in main memory designs. In fact, PCM has higher density and lower idle ... Keywords: hybrid memory, memory controller, phase-change memory

Luiz E. Ramos; Eugene Gorbatov; Ricardo Bianchini

2011-05-01T23:59:59.000Z

452

Google's Hybrid Approach to Research Alfred Spector  

E-Print Network (OSTI)

Google's Hybrid Approach to Research Alfred Spector Google Inc. azs@google.com Peter Norvig Google Inc. pnorvig@google.com Slav Petrov Google Inc. slav@google.com 1 Introduction In this paper, we describe how we organize Computer Science (CS) research at Google. We focus on how we integrate research

Cortes, Corinna

453

Alternative Fuels Data Center: Hybrid Electric Shuttle Buses Offer Free  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Hybrid Electric Hybrid Electric Shuttle Buses Offer Free Rides in Maryland to someone by E-mail Share Alternative Fuels Data Center: Hybrid Electric Shuttle Buses Offer Free Rides in Maryland on Facebook Tweet about Alternative Fuels Data Center: Hybrid Electric Shuttle Buses Offer Free Rides in Maryland on Twitter Bookmark Alternative Fuels Data Center: Hybrid Electric Shuttle Buses Offer Free Rides in Maryland on Google Bookmark Alternative Fuels Data Center: Hybrid Electric Shuttle Buses Offer Free Rides in Maryland on Delicious Rank Alternative Fuels Data Center: Hybrid Electric Shuttle Buses Offer Free Rides in Maryland on Digg Find More places to share Alternative Fuels Data Center: Hybrid Electric Shuttle Buses Offer Free Rides in Maryland on AddThis.com... June 18, 2010

454

Advanced Vehicle Testing Activity: Plug-in Hybrid Electric Vehicles  

NLE Websites -- All DOE Office Websites (Extended Search)

Plug-in Hybrid Electric Vehicles to someone by E-mail Share Advanced Vehicle Testing Activity: Plug-in Hybrid Electric Vehicles on Facebook Tweet about Advanced Vehicle Testing...

455

Hybrid Heterogeneous Energy Supply Networks Farinaz Koushanfar and Azalia Mirhoseini  

E-Print Network (OSTI)

-level system realization for a hybrid network of energy supply options [2]. Recently a hybrid battery-supercapacitor supercapacitor and solar energy generation system in optimizing system's efficiency and dynamic response time

456

Benefits of battery-uItracapacitor hybrid energy storage systems  

E-Print Network (OSTI)

This thesis explores the benefits of battery and battery-ultracapacitor hybrid energy storage systems (ESSs) in pulsed-load applications. It investigates and quantifies the benefits of the hybrid ESS over its battery-only ...

Smith, Ian C., S.M. (Ian Charles). Massachusetts Institute of Technology

2012-01-01T23:59:59.000Z

457

Fuel Economy of the 2013 Toyota Highlander Hybrid 4WD  

NLE Websites -- All DOE Office Websites (Extended Search)

Highlander Hybrid 4WD Search for Other Vehicles View the Mobile Version of This Page 6 cyl, 3.5 L Automatic (variable gear ratios) Regular Gasoline Compare Side-by-Side Hybrid EPA...

458

Vehicle Technologies Office: Draft Plug-In Hybrid Electric Vehicle...  

NLE Websites -- All DOE Office Websites (Extended Search)

Draft Plug-In Hybrid Electric Vehicle R&D Plan to someone by E-mail Share Vehicle Technologies Office: Draft Plug-In Hybrid Electric Vehicle R&D Plan on Facebook Tweet about...

459

Vehicle Technologies Office: Fact #251: January 20, 2003 Hybrid...  

NLE Websites -- All DOE Office Websites (Extended Search)

1: January 20, 2003 Hybrid Vehicle Sales to someone by E-mail Share Vehicle Technologies Office: Fact 251: January 20, 2003 Hybrid Vehicle Sales on Facebook Tweet about Vehicle...

460

Hybrid & electric vehicle technology and its market feasibility  

E-Print Network (OSTI)

In this thesis, Hybrid Electric Vehicles (HEV), Plug-In Hybrid Electric Vehicle (PHEV) and Electric Vehicle (EV) technology and their sales forecasts are discussed. First, the current limitations and the future potential ...

Jeon, Sang Yeob

2010-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "hybrid tractor evaluation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Do You Drive a Hybrid Electric Vehicle? | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Drive a Hybrid Electric Vehicle? Do You Drive a Hybrid Electric Vehicle? July 9, 2009 - 1:34am Addthis In Tuesday's entry, Francis X. Vogel from the Wisconsin Clean Cities...

462

A study in hybrid vehicle architectures : comparing efficiency and performance  

E-Print Network (OSTI)

This paper presents a comparison of performance and efficiencies for four vehicle power architectures; the internal combustion engine (ICE), the parallel hybrid (i.e. Toyota Prius), the serial hybrid (i.e. Chevrolet Volt), ...

Cotter, Gavin M

2009-01-01T23:59:59.000Z

463

Vehicle Technologies Office: Fact #322: May 31, 2004 Hybrid Vehicle...  

NLE Websites -- All DOE Office Websites (Extended Search)

2: May 31, 2004 Hybrid Vehicle Registrations to someone by E-mail Share Vehicle Technologies Office: Fact 322: May 31, 2004 Hybrid Vehicle Registrations on Facebook Tweet about...

464

Vehicle Technologies Office: Fact #230: August 19, 2002 Hybrid...  

NLE Websites -- All DOE Office Websites (Extended Search)

0: August 19, 2002 Hybrid Electric Vehicles in the United States to someone by E-mail Share Vehicle Technologies Office: Fact 230: August 19, 2002 Hybrid Electric Vehicles in the...

465

Vehicle Technologies Office: Fact #703: November 28, 2011 Hybrid...  

NLE Websites -- All DOE Office Websites (Extended Search)

3: November 28, 2011 Hybrid Vehicles Lose Market Share in 2010 to someone by E-mail Share Vehicle Technologies Office: Fact 703: November 28, 2011 Hybrid Vehicles Lose Market...

466

Vehicle Technologies Office: Fact #511: March 24, 2008 Hybrid...  

NLE Websites -- All DOE Office Websites (Extended Search)

1: March 24, 2008 Hybrid and Flex-fuel Vehicles Increase while Diesels Experience a Decline to someone by E-mail Share Vehicle Technologies Office: Fact 511: March 24, 2008 Hybrid...

467

Vehicle Technologies Office: Fact #381: July 18, 2005 Hybrid...  

NLE Websites -- All DOE Office Websites (Extended Search)

1: July 18, 2005 Hybrid Vehicle Registrations, 2000-2004 to someone by E-mail Share Vehicle Technologies Office: Fact 381: July 18, 2005 Hybrid Vehicle Registrations, 2000-2004 on...

468

NREL: Learning - Plug-In Hybrid Electric Vehicles  

NLE Websites -- All DOE Office Websites (Extended Search)

Plug-In Hybrid Electric Vehicles Photo of a parked blue compact car with large decals on the doors stating that it is a plug-in hybrid achieving more than 120 miles per gallon....

469

Cooperative Regulation of Emissions Using Plug-in Hybrid Vehicles  

Science Conference Proceedings (OSTI)

We exploit new types of vehicles, such as Plug-in Hybrid Electric Vehicles (PHEVs), to control transport related emissions in urban environments. By appropriately choosing whether single power-split hybrid vehicles should be operated in fully electric ...

A. Schlote, F. Hausler, T. Hecker, A. Bergmann, E. Crisostomi, I. Radusch, R. Shorten

2012-12-01T23:59:59.000Z

470

Filamentation instability of lower hybrid waves in a plasma  

SciTech Connect

It is shown that a strong lower hybrid wave is modulationally unstable to perturbations propagating along its own wave vector. The instability relies critically on the finite thermal corrections to the lower hybrid dispersion relation. (auth)

Kaw, P. K.

1976-02-01T23:59:59.000Z

471

Electron-State Hybridization in Heavy-Fermion Systems  

NLE Websites -- All DOE Office Websites (Extended Search)

Electron-State Hybridization in Heavy-Fermion Systems Electron-State Hybridization in Heavy-Fermion Systems Print Wednesday, 27 September 2006 00:00 Heavy-fermion systems are...

472

Alternative Fuels Data Center: Maryland Conserves Fuel With Hybrid Trucks  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Maryland Conserves Maryland Conserves Fuel With Hybrid Trucks to someone by E-mail Share Alternative Fuels Data Center: Maryland Conserves Fuel With Hybrid Trucks on Facebook Tweet about Alternative Fuels Data Center: Maryland Conserves Fuel With Hybrid Trucks on Twitter Bookmark Alternative Fuels Data Center: Maryland Conserves Fuel With Hybrid Trucks on Google Bookmark Alternative Fuels Data Center: Maryland Conserves Fuel With Hybrid Trucks on Delicious Rank Alternative Fuels Data Center: Maryland Conserves Fuel With Hybrid Trucks on Digg Find More places to share Alternative Fuels Data Center: Maryland Conserves Fuel With Hybrid Trucks on AddThis.com... March 5, 2011 Maryland Conserves Fuel With Hybrid Trucks L earn how Maryland is reducing fuel consumption, engine noise, and

473

Alternative Fuels Data Center: Hybrid Electric Vehicle (HEV) and Zero  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Hybrid Electric Hybrid Electric Vehicle (HEV) and Zero Emission Vehicle (ZEV) Purchase Vouchers to someone by E-mail Share Alternative Fuels Data Center: Hybrid Electric Vehicle (HEV) and Zero Emission Vehicle (ZEV) Purchase Vouchers on Facebook Tweet about Alternative Fuels Data Center: Hybrid Electric Vehicle (HEV) and Zero Emission Vehicle (ZEV) Purchase Vouchers on Twitter Bookmark Alternative Fuels Data Center: Hybrid Electric Vehicle (HEV) and Zero Emission Vehicle (ZEV) Purchase Vouchers on Google Bookmark Alternative Fuels Data Center: Hybrid Electric Vehicle (HEV) and Zero Emission Vehicle (ZEV) Purchase Vouchers on Delicious Rank Alternative Fuels Data Center: Hybrid Electric Vehicle (HEV) and Zero Emission Vehicle (ZEV) Purchase Vouchers on Digg Find More places to share Alternative Fuels Data Center: Hybrid

474

Alternative Fuels Data Center: Hybrid Electric Vehicle (HEV) High Occupancy  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Hybrid Electric Hybrid Electric Vehicle (HEV) High Occupancy Vehicle (HOV) Lane Exemption to someone by E-mail Share Alternative Fuels Data Center: Hybrid Electric Vehicle (HEV) High Occupancy Vehicle (HOV) Lane Exemption on Facebook Tweet about Alternative Fuels Data Center: Hybrid Electric Vehicle (HEV) High Occupancy Vehicle (HOV) Lane Exemption on Twitter Bookmark Alternative Fuels Data Center: Hybrid Electric Vehicle (HEV) High Occupancy Vehicle (HOV) Lane Exemption on Google Bookmark Alternative Fuels Data Center: Hybrid Electric Vehicle (HEV) High Occupancy Vehicle (HOV) Lane Exemption on Delicious Rank Alternative Fuels Data Center: Hybrid Electric Vehicle (HEV) High Occupancy Vehicle (HOV) Lane Exemption on Digg Find More places to share Alternative Fuels Data Center: Hybrid

475

Plug-In Hybrid Electric Vehicles - PHEV Modeling - Component Technologies  

NLE Websites -- All DOE Office Websites (Extended Search)

Technologies Impact on Fuel Efficiency Technologies Impact on Fuel Efficiency One of the main objectives of the U.S. Department of Energy's (DOE's) Plug-in Hybrid Electric Vehicle (PHEV) R&D Plan (2.2Mb pdf) is to "determine component development requirements" through simulation analysis. Overall fuel efficiency is affected by component technologies from a component sizing and efficiency aspect. To properly define component requirements, several technologies for each of the main components (energy storage, engine and electric machines) are being compared at Argonne using PSAT. Per the R&D plan, several Li-ion battery materials are being modeled to evaluate their impacts on fuel efficiency and vehicle mass. Different Power to Energy ratios are being considered to understand the relative impact of power and energy.

476

Plug-In Hybrid Electric Vehicles - PHEV Modeling - Powertrain Configuration  

NLE Websites -- All DOE Office Websites (Extended Search)

Impact of Powertrain Configuration on Fuel Efficiency To evaluate the fuel efficiency potential of plug-in hybrid electric vehicles, it is necessary to compare the advantages and drawbacks of several powertrain configurations, ranging from power split to parallel and series. PSAT offers the unique ability to simulate and compare hundreds of powertrain configurations. The goal of the effort is to define the most promising configurations depending on the particular usage. Component sizes, fuel efficiency and cost will be used to make appropriate decisions. The configurations currently being considered include, but are not limited to: Pre-transmission parallel HEV Post-transmission parallel HEV Power split HEV (including THS II and GM 2 Mode) Series The figure below shows an example comparison of three powertrain configurations (parallel, series and power split).

477

Fluorescence and Hybrid Detection Aperture of the Pierre Auger Observatory  

E-Print Network (OSTI)

The aperture of the Fluorescence Detector (FD) of the Pierre Auger Observatory is evaluated from simulated events using different detector configurations: mono, stereo, 3-FD and 4-FD. The trigger efficiency has been modeled using shower profiles with ground impacts in the field of view of a single telescope and studying the trigger response (at the different levels) by that telescope and by its neighbours. In addition, analysis cuts imposed by event reconstruction have been applied. The hybrid aperture is then derived for the Auger final extension. Taking into account the actual Surface Detector (SD) array configuration and its trigger response, the aperture is also calculated for a typical configuration of the present phase.

J. A. Bellido; D. D'Urso; H. Geenen; F. Guarino; L. Perrone; S. Petrera; L. Prado Jr.; F. Salamida

2005-07-05T23:59:59.000Z

478

Hybrid Contacts for CZT Virtual Frisch-grid Detectors  

Science Conference Proceedings (OSTI)

In our previous design of virtual Frisch-grid CdZnTe (CZT) detectors, the charge drift-lines can be terminated at the side surfaces before the carriers reach the collecting anode; this results in a loss of signal from the interacting events near the detector's edges. Here, we describe our new design for the anode contact that reduces these edge effects by focusing the electric field towards the detectors' central axes. Four detectors were fabricated with the new hybrid anode contact, and their performances were evaluated and compared to those from the previous design for our virtual Frisch-grid detectors. The results obtained for all four showed similar improvement: therefore, we illustrate them with the findings from one detector.

Camarda G.; Bolotnikov, A.E.; Chan, W.; Cui, Y.; Gul R.; Hossain, A.; Kim, K.; Yang, G.; James, R.B.

2011-08-22T23:59:59.000Z

479

Conversion of Solar Two to a Kokhala hybrid power tower  

DOE Green Energy (OSTI)

The continued drop in energy prices and restructuring of the utility industry have reduced the likelihood that a follow-on commercial 100-MW, power tower project will be built immediately following the Solar Two demonstration project. Given this, it would be desirable to find a way to extend the life of the Solar Two project to allow the plant to operate as a showcase for future power tower projects. This paper looks at the possibility of converting Solar Two into a commercial Kokhala hybrid power tower plant at the end of its demonstration period in 1998. The study identifies two gas turbines that could be integrated into a Kokhala cycle at Solar Two and evaluates the design, expected performance, and economics of each of the systems. The study shows that a commercial Kokhala project at Solar Two could produce power at a cost of less than 7 e/kWhr.

Price, H.W.

1997-06-01T23:59:59.000Z

480

Battery control system for hybrid vehicle and method for controlling a hybrid vehicle battery  

DOE Patents (OSTI)

A battery control system for hybrid vehicle includes a hybrid powertrain battery, a vehicle accessory battery, and a prime mover driven generator adapted to charge the vehicle accessory battery. A detecting arrangement is configured to monitor the vehicle accessory battery's state of charge. A controller is configured to activate the prime mover to drive the generator and recharge the vehicle accessory battery in response to the vehicle accessory battery's state of charge falling below a first predetermined level, or transfer electrical power from the hybrid powertrain battery to the vehicle accessory battery in response to the vehicle accessory battery's state of charge falling below a second predetermined level. The invention further includes a method for controlling a hybrid vehicle powertrain system.

Bockelmann, Thomas R. (Battle Creek, MI); Hope, Mark E. (Marshall, MI); Zou, Zhanjiang (Battle Creek, MI); Kang, Xiaosong (Battle Creek, MI)

2009-02-10T23:59:59.000Z

Note: This page contains sample records for the topic "hybrid tractor evaluation" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Computer aided design tool for electric, hybrid electric and plug-in hybrid electric vehicles  

Science Conference Proceedings (OSTI)

This research is focused on designing a new generation of CAD tools that could help a ”hybrid vehicle” designer with the design process to come up with better vehicle configurations.The conventional design process for any type ...

Ali Eskandari Halvaii / Mehrdad Ehsani

2011-01-01T23:59:59.000Z

482

The HybridTree: a hybrid constructive shape representation for free-form modeling  

Science Conference Proceedings (OSTI)

In this paper, we describe a hybrid modeling framework for creating complex 3D objects incrementally. Our system relies on an extended CSG tree that assembles skeletal implicit primitives, triangle meshes and point set models in a coherent fashion: we ...

Rémi Allègre; Eric Galin; Raphaëlle Chaine; Samir Akkouche

2008-01-01T23:59:59.000Z

483

Tempe Transportation Division: LNG Turbine Hybrid Electric Buses  

SciTech Connect

Fact sheet describes the performance of liquefied natural gas (LNG) turbine hybrid electric buses used in Tempe's Transportation Division.

Not Available

2002-02-01T23:59:59.000Z

484

Optimum Performance of Direct Hydrogen Hybrid Fuel Cell Vehicles  

E-Print Network (OSTI)

of an experimental fuel cell/supercapacitor-powered hybridof fuel cell/battery/supercapacitor hybrid power source for

Zhao, Hengbing; Burke, Andy

2009-01-01T23:59:59.000Z

485

The Green Production of Hybrid Poly(lactide) / Layered ...  

Science Conference Proceedings (OSTI)

The Green Production of Hybrid Poly(lactide) / Layered Double Hydroxide Nanocomposites. ED McCarthy, JW Gilman, P ...

486

Compact Tokamaks as Convenient Neutron Sources for Hybrid Reactors  

Science Conference Proceedings (OSTI)

Fusion-Fission Hybrids and Transmutation / Proceedings of the Fifteenth International Conference on Emerging Nuclear Energy Systems

M. Zucchetti; F. Bombarda; B. Coppi

487

Electron distribution function during lower-hybrid heating  

SciTech Connect

The acceleration of electrons during lower-hybrid heating is suppressed by a nonlinear interaction of parametrically excited waves.

Litvin, S.B.; Tikhonchuk, V.T.

1980-03-01T23:59:59.000Z

488

A Fusion Hybrid Reactor Based on the Gasdynamic Mirror (GDM)  

Science Conference Proceedings (OSTI)

Fusion-Fission Hybrids and Transmutation / Proceedings of the Fifteenth International Conference on Emerging Nuclear Energy Systems

Terry Kammash

489

Polysulfone /Multi-Walled Carbon Nanotube Hybrid Nanocomposites  

Science Conference Proceedings (OSTI)

Abstract Scope, Polyurethane (PU)/ polysulfone/multi-walled carbon nanotubes ( MWNTs) hybrid nanocomposites of different weight ratio have been prepared ...

490

Energy Management Strategies for Plug-In Hybrid Electric Vehicles  

DOE Green Energy (OSTI)

Summarizes and compares potential energy management strategies for plug-in hybrid electric vehicles, accounting for duty cycle distance.

Gonder, J.; Markel, T.

2007-05-01T23:59:59.000Z

491

Two-Phase Spray Cooling of Hybrid Vehicle Electronics: Preprint  

DOE Green Energy (OSTI)

Spray cooling is a feasible cooling technology for hybrid vehicle electronics; HFE 7100 is a promising coolant.

Mudawar, I.; Bharathan, D.; Kelly, K.; Narumanchi, S.

2008-07-01T23:59:59.000Z

492

Optimization of a CNG series hybrid concept vehicle  

DOE Green Energy (OSTI)

Compressed Natural Gas (CNG) has favorable characteristics as a vehicular fuel, in terms of fuel economy as well as emissions. Using CNG as a fuel in a series hybrid vehicle has the potential of resulting in very high fuel economy (between 26 and 30 km/liter, 60 to 70 mpg) and very low emissions (substantially lower than Federal Tier II or CARB ULEV). This paper uses a vehicle evaluation code and an optimizer to find a set of vehicle parameters that result in optimum vehicle fuel economy. The vehicle evaluation code used in this analysis estimates vehicle power performance, including engine efficiency and power, generator efficiency, energy storage device efficiency and state-of-charge, and motor and transmission efficiencies. Eight vehicle parameters are selected as free variables for the optimization. The optimum vehicle must also meet two perfect requirements: accelerate to 97 km/h in less than 10 s, and climb an infinitely long hill with a 6% slope at 97 km/h with a 272 kg (600 lb.) payload. The optimizer used in this work was originally developed in the magnetic fusion energy program, and has been used to optimize complex systems, such as magnetic and inertial fusion devices, neutron sources, and mil guns. The optimizer consists of two parts: an optimization package for minimizing non-linear functions of many variables subject to several non-linear equality and/or inequality constraints and a programmable shell that allows interactive configuration and execution of the optimizer. The results of the analysis indicate that the CNG series hybrid vehicle has a high efficiency and low emissions. These results emphasize the advantages of CNG as a near-term alternative fuel for vehicles.

Aceves, S.M.; Smith, J.R.; Perkins, L.J.; Haney, S.W.; Flowers, D.L.

1995-09-22T23:59:59.000Z

493

Electric and hybrid vehicles program. 5th annual report to Congress for Fiscal Year 1981  

Science Conference Proceedings (OSTI)

This fifth annual report on the implementation of the Electric and Hybrid Vehicle Research, Development and Demonstration Act of 1976 (Public Law 94-413, as amended by Public Law 95-238, referred to as the Act) complies with the reporting requirements established in Section 14 of the Act. In addition to informing the Congress of the progress and plans of the Department of Energy Electric and Hybrid Vehicles Program, this report is intended to serve as a communication link between the Department and all of the public and private interests involved in making the program a success. The Annual Report represents the major summary of the Electric and Hybrid Vehicles Program activities; since July 1981, DOE has ceased publication of the EHV Quarterly Reports with Congressional approval. The fourth quarter activities for FY 1981 are included in this report. During FY 1981, significant progress was made toward implementing the policies established by Congress in the Act. There has been a noticeable increase in interest shown by both the automobile manufacturing and the supply sectors of our economy in electric and hybrid vehicles. This year, the emphasis in the Electric and Hybrid Vehicles Program shifted from vehicle demonstration and preparation for production readiness to research, development, test, and evaluation of advanced technologies to achieve the attributes necessary to make electric and hybrid vehicles a practical transportation alternative. Research and development efforts in batteries and propulsion components, as well as total vehicle systems, continue to reveal significant progress toward providing industry with technology options that will result in vehicles with greater public acceptance.

None

1982-03-01T23:59:59.000Z

494