Powered by Deep Web Technologies
Note: This page contains sample records for the topic "hrsg heat recovery" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Heat Recovery Steam Generator (HRSG) Deposits  

Science Conference Proceedings (OSTI)

Under-deposit corrosion represents the second leading mechanism of chemistry-influenced heat recovery steam generator (HRSG) tube failures (HTFs) and third leading cause of major availability losses. This report was prepared, in recognition of the lack of information, to assemble the state of knowledge on deposition in HRSG high-pressure (HP) evaporator tubing and to identify the major deficiencies in that knowledge. Findings of this effort can be used to establish immediate remediation and correction of...

2009-11-11T23:59:59.000Z

2

Heat Recovery Steam Generator (HRSG) Chemical Cleaning Guidelines Case Studies  

Science Conference Proceedings (OSTI)

A considerable number of combined cycle units with heat recovery steam generators (HRSGs) were installed over the past two decades worldwide, and the design complexity and operating pressures of these units increased significantly during this period. One of the goals of EPRI's Heat Recovery Steam Generator (HRSG) Dependability Program 88 is to minimize availability losses associated with HRSG tube failures. To support its members operating combined cycle units, EPRI published Heat Recovery Steam Generato...

2006-11-13T23:59:59.000Z

3

Examination of Heat Recovery Steam Generator (HRSG) Plants  

Science Conference Proceedings (OSTI)

Previous EPRI reports have documented problems associated with operation and maintenance of complex heat recovery steam generators (HRSGs). The EPRI report Heat Recovery Steam Generator Tube Failure Manual (1004503) provides information about known HRSG tube failures and necessary steps that can be taken to diagnose and prevent similar problems. The EPRI report Delivering High Reliability Heat Recovery Steam Generators (1004240) provides guidance for continued and reliable operation of HRSGs from initial...

2005-11-30T23:59:59.000Z

4

Heat Recovery Steam Generator (HRSG) Chemical Cleaning Guidelines  

Science Conference Proceedings (OSTI)

Combined cycle units with heat recovery steam generators (HRSGs) represent a substantial fraction of the new fossil generating capacity installed around the world since the 1990s. One of the goals of the EPRI HRSG Dependability Program is to make availability losses due to tube failures very low, no more than one per year. An earlier guideline, "Interim Cycle Chemistry Guidelines for Combined Cycle Heat Recovery Steam Generators" (EPRI Report TR-110051), shows organizations how to set up chemistry progra...

2003-12-03T23:59:59.000Z

5

Troubleshooting Guide for Thermal Transients in Heat Recovery Steam Generators (HRSG)  

Science Conference Proceedings (OSTI)

Over the period 2000-2009 EPRI developed ten reports and guidance documents on Heat Recovery Steam Generator (HRSG) thermal transients. Collectively, these documents provide the information required to identify, address, and minimize thermal transients in HRSG superheaters, reheaters, economizers, and evaporators. This summary report offers an overview of this EPRI work on HRSG transients organized to guide the reader to pertinent sections in the original reports and facilitate troubleshooting.

2009-11-09T23:59:59.000Z

6

Heat Recovery Steam Generator Procurement Guideline: HRSG Design Best Practices and Specification for Cyclic Duty  

Science Conference Proceedings (OSTI)

This document provides a summary of best practices for designing a new heat recovery steam generator (HRSG) for cycling and rapid start duty, including typical performance requirements and suggestions for design improvements to improve the HRSGs ability to handle cyclic operation. This document also provides a generic procurement specification for the definition and purchase of an HRSG for installation downstream of a combustion turbine. It includes both horizontal and vertical configuration options. The...

2009-12-16T23:59:59.000Z

7

HRSG Startup and Shutdown Guidelines for Avoiding Heat Recovery Steam Generator Pressure Part Failures  

Science Conference Proceedings (OSTI)

Most of the damage to heat recovery steam generator (HRSG) pressure parts is caused by transiently high thermal-mechanical stresses that occur during shutdown and startup, along with cycle chemistry changes imposed by cyclic operation. Unit shutdown and startup impose considerably more potential for cumulative pressure part damage than stable on-load operation does. Essentially every HRSG damage mechanism is exacerbated by cyclic operationeither directly, through transiently high localized stresses appli...

2009-07-28T23:59:59.000Z

8

Compilation of EPRI Heat Recovery Steam Generator (HRSG) Guidelines  

Science Conference Proceedings (OSTI)

Combined-cycle units with heat recovery steam generators (HRSGs) represent a substantial portion of new installed generation worldwide since the 1990s. Despite being relative new, these units have experienced a significant loss of availability and reliability due to tubing failures. Many of these failures are attributed to poor design, improper operation, weaknesses in fabrication, and poor installation practices. This product is a compilation of nine (9) key individual guidelines developed to address re...

2007-12-20T23:59:59.000Z

9

Proceedings: International Conference on Boiler Tube Failures and Heat Recovery Steam Generator (HRSG) Tube Failures and Inspections  

SciTech Connect

Tube failures remain the leading cause of availability loss in conventional fossil plants and combined cycle/heat recovery steam generator (HRSG) plants. These conference proceedings address state-of-the-art practices and techniques worldwide for understanding and reducing tube failures.

None

2002-10-01T23:59:59.000Z

10

Heat Recovery Steam Generators for Combined Cycle Applications: HRSG Procurement, Design, Construction, and Operation Update  

Science Conference Proceedings (OSTI)

Design alternatives and procurement approaches for heat recovery steam generators, supplemental firing duct burners, and ancillary steam systems are addressed in this report. Power engineers and project developers will find an up-to-date, comprehensive resource for planning, specification and preliminary design in support of combined cycle plant development.

2005-03-29T23:59:59.000Z

11

Temperature profiles determine HRSG steam production  

Science Conference Proceedings (OSTI)

This article examine how temperature profiles affect steam production in heat recovery steam generators(HRSG). A typical gas/steam temperature profile for a HRSG is shown. Heat balance equations for the superheater, evaporator, and the complete HRSG are given along with examples for calculating the HRSG temperature profiles after assuming the pinch and approach point temperatures.

Ganapathy, V.

1993-05-01T23:59:59.000Z

12

Estimate HRSG performance quickly  

SciTech Connect

Heat recovery steam generators (HRSG) are coupled to a heat recovery source which exhausts hot gases, such as gas turbines, furnaces, kilns, etc., to generate steam for the plant's process or power needs. When two pieces of equipment are coupled, their performances may not match their respective design or maximum efficiency points due to varying plant load or steam demand. In addition, many plants require the HRSG to operate effectively over the entire operating range of the plant. In chemical and fertilizer plants, hot gas is cooled in the HRSG to the required limiting temperature. In plants using gas turbines, even ambient conditions will affect HRSG performance indirectly. So a plant engineer should be able to predict the HRSG performance at any design point called for by the plant's load or steam demand.

Kuppuraj, K.

1986-07-01T23:59:59.000Z

13

Troubleshoot HRSG corrosion problems  

SciTech Connect

Heat-recovery steam generators (HRSGs) have come of age. At the same time, these boilers are more complex as designs are refined to maximize heat recovery. Hundreds of units are installed and now have years of operating experience providing valuable information that can benefit all HRSG owners. Experienced troubleshooters can anticipate potential problem areas and recommend cost-effective solutions. The HRSG corrosion problems summarized here--and the means by which they were identified and solved--are useful examples to alert other HRSG owners and operators to potential problem areas. Steps involved include thorough inspection and documentation, problem and cost/benefit analyses, and planning around outages.

Stanley, L.

1996-07-01T23:59:59.000Z

14

Variables Influencing HRSG Designs  

E-Print Network (OSTI)

Heat Recovery Steam Generators (HRSG's) are widely used in chemical plants, refineries, incineration and cogeneration systems and in general for recovering energy from waste gas streams. In applications such as hydrogen or sulfuric acid plants, the duty and exit gas temperature from the HRSG are set by process considerations while the energy recovery potential in other applications is impacted by considerations of efficiency. In addition, low or high temperature corrosion, space availability, duty, size and maintenance aspects play a vital role in the design and sizing of HRSG's. This paper will address a few of the above considerations.

Ganapathy, V.; Rentz, J.

1990-06-01T23:59:59.000Z

15

Applications of HRSG Simulation  

E-Print Network (OSTI)

Heat Recovery Steam Generators are widely used in cogeneration and combined cycle plants generating steam utilizing energy from gas turbine exhaust. Before planning cogen projects, consultants should study various options available in terms of steam parameters and select the optimum. Simulation helps plan such studies. In addition, useful "what if" studies can be performed without even designing the HRSG, thus saving valuable time. This article outlines the applications of HRSG simulation and how plant engineers, consultants can benefit from such studies.

Ganapathy, V. V.

1995-04-01T23:59:59.000Z

16

Monitoring and Controlling Carryover in Heat Recovery Steam Generators  

Science Conference Proceedings (OSTI)

Optimization of the cycle chemistry in the steam generating system of combined-cycle/heat recovery steam generator (HRSG) plants is vital to ensuring the efficient and reliable operation of the equipment. Monitoring of steam purity and drum carryover are core parameters for HRSG chemistry programs. Carryover is any solid, liquid, or vaporous contaminant that leaves the HRSG steam drum along with the steam. Carryover might be the result of the limited separation of the steam/water mixture in the steam dru...

2010-10-27T23:59:59.000Z

17

Remote Inspection Device - Heat Recovery Steam Generators  

Science Conference Proceedings (OSTI)

As heat recovery steam generators (HRSGs) have become more complex over the last 15 years, operating with multiple pressures and temperatures, operators have experienced more types of HRSG tube failures (HTFs). This report provides information on how nondestructive evaluation (NDE) can be combined with newly developed HRSG repair tooling so that operators can detect damaged tubes and verify that repaired tubes do not contain welding defects that might be detrimental to the life of the component.

2009-03-25T23:59:59.000Z

18

Field Guide: Heat Recovery Steam Generator Tube Failure  

Science Conference Proceedings (OSTI)

In conventional and combined-cycle plants, boiler and heat recovery steam generator (HRSG) tube failures have been the main availability problem for as long as reliable statistics have been kept for each generating source. The three volumes of the Electric Power Research Institute (EPRI) report Boiler and Heat Recovery Steam Generator Tube Failures: Theory and Practice (1012757) present an in-depth description of the various HRSG and degradation mechanisms, providing plant owners and operators with the t...

2010-12-15T23:59:59.000Z

19

Evaluation of Thermal-, Creep-, and Corrosion-Fatigue of Heat Recovery Steam Generator Pressure Parts  

Science Conference Proceedings (OSTI)

The worldwide fleet of combined cycle units with heat recovery steam generators (HRSG) has exhibited a disappointing track record with respect to reliability and availability in terms of fatigue HRSG tube failures (HTF) which are thermal transient driven. This report, which forms part of a series, will assist designer, owners, and operators with the technical basis to facilitate specifying, designing, and operating HRSG in a manner to minimize fatigue damage.

2006-03-31T23:59:59.000Z

20

Heat Recovery Steam Generator Materials Selection Guideline  

Science Conference Proceedings (OSTI)

A considerable number of failures have occurred over the past decade in heat recovery steam generators (HRSGs). Many of these failures are attributed to poor design, improper operation, poor fabrication, or poor installation practices, but a number of them are attributed directly to improper material selection. In March 2004, the Electric Power Research Institute (EPRI) published the first heat recovery steam generator materials selection and repair guidelines (HRSG Material Selection and Repair Guidelin...

2010-12-19T23:59:59.000Z

Note: This page contains sample records for the topic "hrsg heat recovery" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Heat Recovery Steam Generator Simulation  

E-Print Network (OSTI)

The paper discusses the applications of Heat Recovery Steam Generator Simulation. Consultants, plant engineers and plant developers can evaluate the steam side performance of HRSGs and arrive at the optimum system which matches the needs of the process plant, cogeneration or combined cycle plant. There is no need to design the HRSG per se and hence simulation is a valuable tool for anyone interested in evaluating the HRSG performance even before it is designed. It can also save a lot of time for specification writers as they need not guess how the steam side performance will vary with different gas/steam parameters. A few examples are given to show how simulation methods can be applied to real life problems.

Ganapathy, V.

1993-03-01T23:59:59.000Z

22

Delivering High Reliability in Heat Recovery Steam Generators  

Science Conference Proceedings (OSTI)

Despite being relatively new, the worldwide fleet of combined-cycle units with heat recovery steam generators (HRSGs) has exhibited a disappointing record with respect to reliability and availability in terms of HRSG tube failures (HTFs). This report identifies actions that—if implemented prior to commercial operation—should greatly improve the operational HRSG reliability.BackgroundWhen contemplating new combined-cycle units, the choices that can ...

2012-12-12T23:59:59.000Z

23

HRSG design method optimizes power plant efficiency  

SciTech Connect

Heat recovery steam generators (HRSGs) are widely used in cogeneration and combined-cycle power plants. simulating the performance of the HRSG system at design and off-design conditions helps the designer optimize the overall plant efficiency. It also helps in the selection of major auxiliary equipment. Conventional simulation of HRSG design and off-design performance is a tedious task, since there are several variables involved. However, with the simplified approach presented in this article, the engineer can acquire information on the performance of the HRSG without actually doing the mechanical design. The engineer does not need to size the tubes or determine the fin configuration. This paper reports that the method also can be used for heat balance studies and in the preparation of the HRSG specification.

Ganapathy, V. (ABCO (US))

1991-05-01T23:59:59.000Z

24

Development of Advanced Nondestructive Evaluation Techniques for Heat Recovery Steam Generators  

Science Conference Proceedings (OSTI)

Contemporary heat recovery steam generators (HRSGs) operate with multiple pressures and temperatures that can result in degradation and failure of key components such as HRSG drains. Periodic nondestructive evaluation (NDE) of HRSGs can mitigate catastrophic component failure as well as facilitate effective maintenance planning through early detection of system damage. This technical update describes HRSG drain damage mechanisms and related NDE techniques.

2009-03-27T23:59:59.000Z

25

Dynamic simulation model for non-supplementary firing triple-pressure heat recovery steam generator  

Science Conference Proceedings (OSTI)

By using the modular modeling method, a real-time dynamic simulation model for the non-supplementary tri-pressure reheat Heat Recovery Steam Generator (HRSG) is developed. On the basis of mass and energy conservation law, the paper discusses the model ... Keywords: HRSG, dynamic model, modular modelling, simulation

Ning Cui; Bing-Shu Wang; Xiang-Yang Gong; Jian-Qiang Gao

2007-10-01T23:59:59.000Z

26

Cycle Chemistry Guidelines for Combined Cycle/Heat Recovery Steam Generators (HRSGs)  

Science Conference Proceedings (OSTI)

The cycle chemistry in combined cycle plants influences about 70 of the heat recovery steam generator (HRSG) tube failure mechanisms. These guidelines have been assembled to assist operators and chemists in developing an effective overall cycle chemistry program which will prevent HRSG tube failures (HTF).

2006-03-09T23:59:59.000Z

27

Design of a heat recovery steam generator  

SciTech Connect

A gas turbine in the size range of 20,000 hp (14.9 MW) was retrofitted with a heat recovery steam generator (HRSG). The HRSG produces high pressure superheated steam for use in a steam turbine. Supplementary firing is used to more than double the steam production over the unfired case. Because of many unusual constraints, an innovative design of the HRSG was formulated. These design constraints included: a wide range of operating conditions was to be accommodated; very limited space in the existing plant; and a desire to limit the field construction work necessary in order to provide a short turnaround time. This paper discusses the design used to satisfy these conditions.

Logeais, D.R.

1984-06-01T23:59:59.000Z

28

Induced draft fan innovation for heat recovery steam generators  

SciTech Connect

A first of its kind, induced draft (ID) heat recovery steam generators (HRSG) have been in service at a cogeneration facility since 1991. A preliminary engineering study considered a forced draft (FD) fan to supply combustion air to the HRSG duct burners (when the combustion turbine (CT) is out of service) as a traditional design; however, the study indicated that the FD fan may require the HRSG duct burner to be shut off following a CT trip and re-ignited after the FD fan was in service. Although the induced draft HRSG design cost more than the FD fan design, the induced draft design has improved the cogeneration facility's steam generation reliability by enabling the HRSG to remain in service following a CT trip. This paper briefly summarizes the preliminary engineering study that supported the decision to select the ID fan design. The paper also discusses the control system that operates the fresh-air louvers, duct burners, HRSG, and ID fan during a CT trip. Startup and operating experiences are presented that demonstrate the effectiveness of the design. Lessons learned are also summarized for input into future induced draft HRSG designs.

Beasley, O.W.; Hutchins, E.C. (Oklahoma Gas and Electric Co., Oklahoma City, OK (United States)); Predick, P.R.; Vavrek, J.M. (Sargent and Lundy, Chicago, IL (United States))

1994-04-01T23:59:59.000Z

29

Heat Recovery Steam Generator Cycle Chemistry Instrumentation  

Science Conference Proceedings (OSTI)

Effective monitoring of the purity of water and steam is an integral part of any productive cycle chemistry monitoring program. The Electric Power Research Institute's (EPRI's) heat recovery steam generator (HRSG) cycle chemistry guidelines identified a group of core monitoring parameters that are considered the minimum requirements. Meeting these requirements is part of EPRI's cycle chemistry benchmarking criteria for HRSGs. In addition to the core parameters, many chemistry parameters might need to be ...

2010-11-19T23:59:59.000Z

30

HRSG Material Selection and Repair Guidelines  

Science Conference Proceedings (OSTI)

The number of failures in heat recovery steam generator (HRSG) components has been quite high during the past decade. Many of these failures are attributed to poor design, improper operation, poor fabrication, or poor installation practices. This report provides repair practices and procedures currently being used to correct a number of these problems. It also identifies domestic and international materials commonly employed.

2004-03-31T23:59:59.000Z

31

Evaluation of a once-through heat recovery steam generator concept: Final report  

Science Conference Proceedings (OSTI)

This report presents the results of a reliability, availability, and maintainability (RAM) evaluation of a once-through concept for a combined-cycle heat recovery steam generator (HRSG). The project included a review of differences in reliability and maintainability characteristics of the once-through concept and a typical drum-type HRSG design. A special effort was placed on an investigation of the expected performance of the thin-wall alloy 800 boiler tubing used in the once-through HRSG. An analysis was performed by using the UNIRAM computer modeling methodology to compare the predicted availability of the once-through HRSG design with that of a drum-type system. The results of this project provide a basis for understanding the RAM characteristics of the once-through HRSG concept and identify areas where additional research may be beneficial in evaluating this new design for application within the utility industry. 28 refs., 5 figs., 7 tabs.

Babione, R.A.

1988-04-01T23:59:59.000Z

32

Guidelines for the Nondestructive Examination of Heat Recovery Steam Generators  

Science Conference Proceedings (OSTI)

As heat recovery steam generators (HRSGs) have become more complex over the last 15 years, operating with multiple pressures and temperatures, operators have experienced an increasing suite of HRSG tube failures (HTFs). This report provides guidance on the performance of nondestructive evaluation (NDE) of HRSGs so that operators will know what types of NDE to perform and where to perform them.

2007-02-27T23:59:59.000Z

33

Simplify heat recovery steam generator evaluation  

SciTech Connect

Heat recovery steam generators (HRSGs) are widely used in process and power plants, refineries and in several cogeneration/combined cycle systems. They are usually designed for a set of gas and steam conditions but often operate under different parameters due to plant constraints, steam demand, different ambient conditions (which affect the gas flow and exhaust gas temperature in a gas turbine plant), etc. As a result, the gas and steam temperature profiles in the HRSG, steam production and the steam temperature differ from the design conditions, affecting the entire plant performance and economics. Also, consultants and process engineers who are involved in evaluating the performance of the steam system as a whole, often would like to simulate the performance of an HRSG under different gas flows, inlet gas temperature and analysis, steam pressure and feed water temperature to optimize the entire steam system and select proper auxiliaries such as steam turbines, condensers, deaerators, etc.

Ganapathy, V. (ABCO Industries, Abilene, TX (US))

1990-03-01T23:59:59.000Z

34

Comprehensive Cycle Chemistry Guidelines for Combined Cycle/Heat Recovery Steam Generators (HRSGs)  

Science Conference Proceedings (OSTI)

The purity of water and steam is central to ensuring combined cycle/heat recovery steam generator (HRSG) plant component availability and reliability. These guidelines for combined cycle/HRSG plants provide information on the application of all-volatile treatment (AVT), oxygenated treatment (OT), phosphate treatment (PT), caustic treatment (CT), and amine treatment. The guidelines will help operators reduce corrosion and deposition and thereby achieve significant operation and maintenance cost ...

2013-11-08T23:59:59.000Z

35

Standardization of HRSG production components for large, combined-cycle power plants  

SciTech Connect

Stein Industrie's experience in the development of heat recovery steam generators (HRSG) for combined cycle applications is briefly reviewed. Standardization of several components, the extended use of N.C. machine tools and automatic welding procedures have made it possible to improve quality as well as production costs. This process has been concentrated on three types of HRSG for 35, 100 and 200 MW class gas turbines. 4 figs.

Chellini, R.

1993-06-01T23:59:59.000Z

36

Mass and Heat Recovery  

E-Print Network (OSTI)

In the last few years heat recovery was under spot and in air conditioning fields usually we use heat recovery by different types of heat exchangers. The heat exchanging between the exhaust air from the building with the fresh air to the building (air to air heat exchanger). In my papers I use (water to air heat exchanger) as a heat recovery and I use the water as a mass recovery. The source of mass and heat recovery is the condensate water which we were dispose and connect it to the drain lines.

Hindawai, S. M.

2010-01-01T23:59:59.000Z

37

Evaluating and Avoiding Heat Recovery Steam Generator Tube Damage Caused by Duct Burners  

Science Conference Proceedings (OSTI)

In heat recovery steam generators (HRSGs), supplemental firing in duct burners introduces the potential for serious HRSG tube failure and damage. Duct burners that are specified, designed, and operated properly can produce a number of significant benefits. This report will assist operators in accruing these benefits.

2007-03-20T23:59:59.000Z

38

Boiler and Heat Recovery Steam Generator Tube Failures: Theory and Practice  

Science Conference Proceedings (OSTI)

Boiler and heat recovery steam generator (HRSG) tube failures have been the primary availability problem for operators of conventional and combined cycle plants for as long as reliable statistics have been kept for each generating source. This book provides owners and operators with the technical basis to address tube failures and create permanent solutions.

2011-12-23T23:59:59.000Z

39

ASU nitrogen sweep gas in hydrogen separation membrane for production of HRSG duct burner fuel  

DOE Patents (OSTI)

The present invention relates to the use of low pressure N2 from an air separation unit (ASU) for use as a sweep gas in a hydrogen transport membrane (HTM) to increase syngas H2 recovery and make a near-atmospheric pressure (less than or equal to about 25 psia) fuel for supplemental firing in the heat recovery steam generator (HRSG) duct burner.

Panuccio, Gregory J.; Raybold, Troy M.; Jamal, Agil; Drnevich, Raymond Francis

2013-04-02T23:59:59.000Z

40

Diagnostic/Troubleshooting Monitoring to Identify Damaging Cycle Chemistry or Thermal Transients in Heat Recovery Steam Generator Pressure Parts  

Science Conference Proceedings (OSTI)

The worldwide fleet of combined cycle units with heat recovery steam generators (HRSGs) has exhibited a disappointing track record with respect to reliability and availability in terms of HRSG tube failures (HTFs). This report will assist operators in identifying the harmful chemical and thermal transient excursions that lead to failure.

2005-03-07T23:59:59.000Z

Note: This page contains sample records for the topic "hrsg heat recovery" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Proceedings: International Conference on Boiler Tube and HRSG Tube Failures and Inspections  

Science Conference Proceedings (OSTI)

Tube failures are the leading cause of availability loss in conventional fossil plants and combined cycle/heat recovery steam generator (HRSG) plants. This conference proceedings addresses worldwide state-of-the-art practices and techniques for understanding and reducing tube failures.

2006-08-29T23:59:59.000Z

42

Competitive realities change focus of boiler/HRSG design  

Science Conference Proceedings (OSTI)

This article describes how, faced with competing against gas-fired plants, coal-fired-boiler designers have squeezed cost and scheduling constraints out of their product. Meanwhile, HRSG design reflects the escalating demands placed on modern combined cycles. In the US, emphasis continues to center around reducing construction time and cost. The large capital investment, particularly during the erection phase of the project, and the need to get projects on-line as quickly as possible, have placed a significant premium on fast cycle time. Innovations appear in project implementation strategies rather than on advanced boiler technologies. Perhaps nothing illustrates this last statement better than comparing recent large utility units in the US to those in Europe and japan. At the other end of the scale, heat-recovery steam generator (HRSG) technology is advancing rapidly to keep pace with ever more powerful gas turbines in combined-cycle (CC) configurations. In fact, the once simple HRSG now anchors a complex steam cycle fully integrated with the gas turbine. Triple pressure levels, NO{sub x} injection steam, steam turbine bypass, elevating steam pressures and temperatures, supplementary firing, selective catalytic reduction, and even accommodating a coal-gasification process are a sampling of extras HRSG designers must accommodate.

NONE

1996-02-01T23:59:59.000Z

43

Laundry heat recovery system  

SciTech Connect

A laundry heat recovery system includes a heat exchanger associated with each dryer in the system, the heat exchanger being positioned within the exhaust system of the dryer. A controller responsive to the water temperature of the heat exchangers and the water storage for the washer selectively circulates the water through a closed loop system whereby the water within the exchangers is preheated by the associated dryers. By venting the exhaust air through the heat exchanger, the air is dehumidified to permit recirculation of the heated air into the dryer.

Alio, P.

1985-04-09T23:59:59.000Z

44

Guidelines for the Nondestructive Examination of Heat Recovery Steam Generators, Revision 2  

Science Conference Proceedings (OSTI)

As heat recovery steam generators (HRSGs) have become more complex over the last 20 years, operating with multiple pressures and temperatures, operators have experienced an increasing suite of HRSG tube failures (HTFs). This report provides guidance on the performance of nondestructive evaluation (NDE) of HRSGs so that operators will know what types of NDE to perform and where to perform them.BackgroundModern HRSGs have numerous varieties available within the ...

2013-12-16T23:59:59.000Z

45

Study for Snake Robot Technology for Inspection of Headers and Tubes in Heat Recovery Steam Generators  

Science Conference Proceedings (OSTI)

Heat recovery steam generator (HRSG) tubing is especially difficult to inspect using conventional nondestructive evaluation (NDE) techniques because: The tubing is tightly bundled, with interior bundle tubing typically inaccessible by conventional equipment without cutting and later repairing the exterior tubes. The tubing is finned and, since ultrasonic techniques require solid contact with the tube, cannot be accessed unless the tubing is cut away. Access to the inside of the tubes is difficult, requi...

2009-11-10T23:59:59.000Z

46

Industrial Heat Recovery - 1982  

E-Print Network (OSTI)

Two years ago I summarized 20 years of experience on Industrial Heat Recovery for the Energy-source Technology Conference and Exhibition held in New Orleans, Louisiana. At the end of that paper I concluded with brief advice on 'How to specify heat recovery equipment.' The two years which have elapsed since then have convinced me that proper specification assures the most reliable equipment at the lowest price. The most economical specification describes the operating and site data but leaves the design details for the supplier. A true specialist will be able to provide you with the latest technology at the best possible price. This paper explores the impact of specifications on heat recovery equipment and its associated cost.

Csathy, D.

1982-01-01T23:59:59.000Z

47

Distributed Generation Heat Recovery  

Science Conference Proceedings (OSTI)

Economic and environmental drivers are promoting the adoption of combined heat and power (CHP) systems. Technology advances have produced new and improved distributed generation (DG) units that can be coupled with heat recovery hardware to create CHP systems. Performance characteristics vary considerably among DG options, and it is important to understand how these characteristics influence the selection of CHP systems that will meet both electric and thermal site loads.

2002-03-06T23:59:59.000Z

48

Heat-recovery steam generators: Understand the basics  

Science Conference Proceedings (OSTI)

Gas turbines with heat-recovery steam generators (HRSGs) can be found in virtually every chemical process industries (CPI) plant. They can be operated in either the cogeneration mode or the combined-cycle mode. In the cogeneration mode, steam produced from the HRSG is mainly used for process applications, whereas in the combined-cycle mode, power is generated via a steam turbine generator. Recent trends in HRSG design include multiple-pressure units for maximum energy recovery, the use of high-temperature superheaters or reheaters in combined-cycle plants, and auxiliary firing for efficient steam generation. In addition, furnace firing is often employed in small capacity units when the exhaust gas is raised to temperatures of 2,400--3,000 F to maximize steam generation and thus improve fuel utilization. This article highlights some of the basic facts about gas turbine HRSGs. This information can help plant engineers, consultants, and those planning cogeneration projects make important decisions about the system and performance related aspects.

Ganapathy, V.

1996-08-01T23:59:59.000Z

49

Wastewater heat recovery apparatus  

DOE Patents (OSTI)

A heat recovery system with a heat exchanger and a mixing valve. A drain trap includes a heat exchanger with an inner coiled tube, baffle plate, wastewater inlet, wastewater outlet, cold water inlet, and preheated water outlet. Wastewater enters the drain trap through the wastewater inlet, is slowed and spread by the baffle plate, and passes downward to the wastewater outlet. Cold water enters the inner tube through the cold water inlet and flows generally upward, taking on heat from the wastewater. This preheated water is fed to the mixing valve, which includes a flexible yoke to which are attached an adjustable steel rod, two stationary zinc rods, and a pivoting arm. The free end of the arm forms a pad which rests against a valve seat. The rods and pivoting arm expand or contract as the temperature of the incoming preheated water changes. The zinc rods expand more than the steel rod, flexing the yoke and rotating the pivoting arm. The pad moves towards the valve seat as the temperature of the preheated water rises, and away as the temperature falls, admitting a variable amount of hot water to maintain a nearly constant average process water temperature.

Kronberg, James W. (108 Independent Blvd., Aiken, SC 29801)

1992-01-01T23:59:59.000Z

50

Wastewater heat recovery apparatus  

DOE Patents (OSTI)

A heat recovery system is described with a heat exchanger and a mixing valve. A drain trap includes a heat exchanger with an inner coiled tube, baffle plate, wastewater inlet, wastewater outlet, cold water inlet, and preheated water outlet. Wastewater enters the drain trap through the wastewater inlet, is slowed and spread by the baffle plate, and passes downward to the wastewater outlet. Cold water enters the inner tube through the cold water inlet and flows generally upward, taking on heat from the wastewater. This preheated water is fed to the mixing valve, which includes a flexible yoke to which are attached an adjustable steel rod, two stationary zinc rods, and a pivoting arm. The free end of the arm forms a pad which rests against a valve seat. The rods and pivoting arm expand or contract as the temperature of the incoming preheated water changes. The zinc rods expand more than the steel rod, flexing the yoke and rotating the pivoting arm. The pad moves towards the valve seat as the temperature of the preheated water rises, and away as the temperature falls, admitting a variable amount of hot water to maintain a nearly constant average process water temperature. 6 figs.

Kronberg, J.W.

1992-09-01T23:59:59.000Z

51

Repowering Fossil Steam Plants with Gas Turbines and Heat Recovery Steam Generators: Design Considerations, Economics, and Lessons L earned  

Science Conference Proceedings (OSTI)

This report describes repowering fossil steam plants using gas turbines (GTs) and heat recovery steam generators (HRSGs) in combined-cycle mode. Design considerations and guidance, comparative economics, and lessons learned in the development of such projects are included. Various other methods of fossil plant repowering with GTs are also briefly discussed. The detailed results and comparisons that are provided relate specifically to a generic GT/HRSG repowering. Design parameters, limitations, schedulin...

2012-08-08T23:59:59.000Z

52

Heat Recovery in Building Envelopes  

SciTech Connect

Infiltration has traditionally been assumed to contribute to the energy load of a building by an amount equal to the product of the infiltration flow rate and the enthalpy difference between inside and outside. Application of such a simple formula may produce an unreasonably high contribution because of heat recovery within the building envelope. Previous laboratory and simulation research has indicated that such heat transfer between the infiltrating air and walls may be substantial. In this study, Computational Fluid Dynamics was used to simulate sensible heat transfer in typical envelope constructions. The results show that the traditional method may over-predict the infiltration energy load by up to 95 percent at low leakage rates. A simplified physical model has been developed and used to predict the infiltration heat recovery based on the Peclet number of the flow and the fraction of the building envelope active in infiltration heat recovery.

Sherman, Max H.; Walker, Iain S.

2001-01-01T23:59:59.000Z

53

Heat Recovery from Coal Gasifiers  

E-Print Network (OSTI)

This paper deals with heat recovery from pressurized entrained and fixed bed coal gasifiers for steam generation. High temperature waste heat, from slagging entrained flow coal gasifier, can be recovered effectively in a series of radiant and convection waste heat boilers. Medium level waste heat leaving fixed bed type gasifiers can be recovered more economically by convection type boilers or shell and tube heat exchangers. An economic analysis for the steam generation and process heat exchanger is presented. Steam generated from the waste heat boiler is used to drive steam turbines for power generation or air compressors for the oxygen plant. Low level heat recovered by process heat exchangers is used to heat product gas or support the energy requirement of the gasification plant. The mechanical design for pressure vessel shell and boiler tubes is discussed. The design considers metallurgical requirements associated with hydrogen rich, high temperature, and high pressure atmosphere.

Wen, H.; Lou, S. C.

1981-01-01T23:59:59.000Z

54

Industrial Waste Heat Recovery Using Heat Pipes  

E-Print Network (OSTI)

For almost a decade now, heat pipes with secondary finned surfaces have been utilized in counter flow heat exchangers to recover sensible energy from industrial exhaust gases. Over 3,000 such heat exchangers are now in service, recovering an estimated energy equivalent of nearly 1.1 million barrels of oil annually. Energy recovered by these units has been used to either preheat process supply air or to heat plant comfort make-up air. Heat pipe heat exchangers have been applied to an ever-expanding variety of industrial processes. One notable application in recent years has been for combustion airs preheat of fired heaters in petroleum refineries and petrochemical plants. Another recent development has been a waste heat recovery boiler using heat pipes. This device has a number of advantageous features. Field operational experience of several units in service has been excellent.

Ruch, M. A.

1981-01-01T23:59:59.000Z

55

Low Level Heat Recovery Technology  

E-Print Network (OSTI)

With today's high fuel prices, energy conservation projects to utilize low level waste heat have become more attractive. Exxon Chemical Company Central Engineering has been developing guidelines and assessing the potential for application of low level heat recovery technology. This paper discusses heat distribution systems, latest developments in absorption refrigeration and organic Rankine cycles, and pressure, minimization possibilities. The relative merits and economics of the various possibilities and some guidelines on when they should be considered will be presented.

O'Brien, W. J.

1982-01-01T23:59:59.000Z

56

Carbon Material Based Heat Exchanger for Waste Heat Recovery ...  

Industrial processing plants Nuclear power Solar power ... Carbon Material Based Heat Exchanger for Waste Heat Recovery from Engine Exhaust Contact:

57

Field Performance of Heat Recovery Chillers and Heat Recovery Heat Pumps  

Science Conference Proceedings (OSTI)

Heat recovery chillers and heat recovery heat pumps operate at high efficiency and excellent economy by simultaneously providing both heating and cooling. Although this technology has been in use for more than thirty years and all major chiller manufacturers offer heat recovery models, applications are not yet widespread. One of the barriers to using this technology is the lack of measured performance information on the devices. This project was undertaken to identify and summarize existing sources of pe...

1994-05-18T23:59:59.000Z

58

Drain Water Heat Recovery | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Drain Water Heat Recovery Drain Water Heat Recovery Drain Water Heat Recovery June 15, 2012 - 6:20pm Addthis Diagram of a drain water heat recovery system. Diagram of a drain water heat recovery system. How does it work? Use heat from water you've already used to preheat more hot water, reducing your water heating costs. Any hot water that goes down the drain carries away energy with it. That's typically 80%-90% of the energy used to heat water in a home. Drain-water (or greywater) heat recovery systems capture this energy from water you've already used (for example, to shower, wash dishes, or wash clothing) to preheat cold water entering the water heater or going to other water fixtures. This reduces the amount of energy needed for water heating. How It Works Drain-water heat recovery technology works well with all types of water

59

Drain Water Heat Recovery | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Drain Water Heat Recovery Drain Water Heat Recovery Drain Water Heat Recovery June 15, 2012 - 6:20pm Addthis Diagram of a drain water heat recovery system. Diagram of a drain water heat recovery system. How does it work? Use heat from water you've already used to preheat more hot water, reducing your water heating costs. Any hot water that goes down the drain carries away energy with it. That's typically 80%-90% of the energy used to heat water in a home. Drain-water (or greywater) heat recovery systems capture this energy from water you've already used (for example, to shower, wash dishes, or wash clothing) to preheat cold water entering the water heater or going to other water fixtures. This reduces the amount of energy needed for water heating. How It Works Drain-water heat recovery technology works well with all types of water

60

Heat recovery in building envelopes  

SciTech Connect

Infiltration has traditionally been assumed to contribute to the energy load of a building by an amount equal to the product of the infiltration flow rate and the enthalpy difference between inside and outside. Some studies have indicated that application of such a simple formula may produce an unreasonably high contribution because of heat recovery within the building envelope. The major objective of this study was to provide an improved prediction of the energy load due to infiltration by introducing a correction factor that multiplies the expression for the conventional load. This paper discusses simplified analytical modeling and CFD simulations that examine infiltration heat recovery (IHR) in an attempt to quantify the magnitude of this effect for typical building envelopes. For comparison, we will also briefly examine the results of some full-scale field measurements of IHR based on infiltration rates and energy use in real buildings. The results of this work showed that for houses with insulated walls the heat recovery is negligible due to the small fraction of the envelope that participates in heat exchange with the infiltrating air. However; there is the potential for IHR to have a significant effect for higher participation dynamic walls/ceilings or uninsulated walls. This result implies that the existing methods for evaluating infiltration related building loads provide adequate results for typical buildings.

Walker, Iain S.; Sherman, Max H.

2003-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "hrsg heat recovery" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Industrial Plate Exchangers Heat Recovery and Fouling  

E-Print Network (OSTI)

Plate and Frame Heat Exchangers have special characteristics for both fouling and heat recovery. These are discussed in general then related to two industrial examples.

Cross, P. H.

1981-01-01T23:59:59.000Z

62

Distributed Generation with Heat Recovery and Storage  

E-Print Network (OSTI)

L ABORATORY Distributed Generation with Heat Recovery andequal opportunity employer. Distributed Generation with Heatenergy resources (DER), distributed generation (DG), and

Siddiqui, Afzal S.; Marnay, Chris; Firestone, Ryan M.; Zhou, Nan

2008-01-01T23:59:59.000Z

63

Development of Corrosion Resistant Coatings For The ID Surface Of HRSG Tubes  

Science Conference Proceedings (OSTI)

Flow-accelerated corrosion (FAC) causes wall thinning (metal loss) in tubes due to flow of water or two-phase wet steam. Wall thinning from FAC in proximity of heat recovery steam generator (HRSG) tube elbows has resulted in numerous tube failures. Use of a reliable and durable protective coating would minimize FAC-induced corrosion and avoid steam tube failures. Thus, there is a great need to develop advanced coating deposition methods for applying corrosion-resistant coatings on the internal surface of...

2008-03-19T23:59:59.000Z

64

Waste Heat Recovery from Industrial Process Heating Equipment...  

NLE Websites -- All DOE Office Websites (Extended Search)

Waste Heat Recovery from Industrial Process Heating Equipment - Cross-cutting Research and Development Priorities Speaker(s): Sachin Nimbalkar Date: January 17, 2013 - 11:00am...

65

Evaluation of the Pulsed Eddy Current Inspection Technique Known as the Through-Fin Inspection System for Heat Recovery Steam Genera tors (T-FISH) as Applicable to Power Plants  

Science Conference Proceedings (OSTI)

This project is a continuation of previous work Intertek APTECH did in support of the Electric Power Research Institute EPRI report 1008093, Electromagnetic Nondestructive Evaluation NDE for Heat Recovery Steam Generators HRSGs, 2005. EPRI report 1008093 was an NDE overview report that reviewed different commercially available electromagnetic NDE techniques suitable for HRSG applications involving both finned and nonfinned tubing. The pulsed eddy current PEC methodology demonstrated an ability to detect ...

2009-12-23T23:59:59.000Z

66

An Introduction to Waste Heat Recovery  

E-Print Network (OSTI)

The recovery of waste heat energy is one element of a complete energy conservation plan. In addition to contributing to the goal of saving energy, utilization of waste heat is also an important source of cost savings. This presentation details the steps necessary to develop a good waste heat recovery plan. The necessity of performing a complete waste heat audit is detailed, together with guidelines to selecting waste heat recovery projects. The economic analysis of potential projects, and the art of selling these projects to management are discussed. Also included are brief descriptions of the various types of heat exchangers commonly used in industry today.

Darby, D. F.

1985-05-01T23:59:59.000Z

67

Distributed Generation with Heat Recovery and Storage  

E-Print Network (OSTI)

Distributed Generation with Heat Recovery and Storage ‡energy resources (DER), distributed generation (DG), andload of Figure 2. distributed generation of part or all of

Siddiqui, Afzal; Marnay, Chris; Firestone, Ryan M.; Zhou, Nan

2005-01-01T23:59:59.000Z

68

Waste Heat Recovery from Industrial Process Heating Equipment -  

NLE Websites -- All DOE Office Websites (Extended Search)

Waste Heat Recovery from Industrial Process Heating Equipment - Waste Heat Recovery from Industrial Process Heating Equipment - Cross-cutting Research and Development Priorities Speaker(s): Sachin Nimbalkar Date: January 17, 2013 - 11:00am Location: 90-2063 Seminar Host/Point of Contact: Aimee McKane Waste heat is generated from several industrial systems used in manufacturing. The waste heat sources are distributed throughout a plant. The largest source for most industries is exhaust / flue gases or heated air from heating systems. This includes the high temperature gases from burners in process heating, lower temperature gases from heat treat, dryers, and heaters, heat from heat exchangers, cooling liquids and gases etc. The previous studies and direct contact with the industry as well as equipment suppliers have shown that a large amount of waste heat is not

69

Commercial laundry heat recovery system  

SciTech Connect

In a commercial laundry that is connected to a source of fresh water and generates heated waste water, a method is described for recovering heat from the heated waste comprising the steps of: (a) pumping the heated waste water through a heat exchanger; (b) introducing fresh water into the heat exchanger to receive heat from the waste water through a heat transfer effected by the heat exchanger; (c) withdrawing a first proportion of the heated fresh water at a first temperature; (d) conveying the first proportion of the heated fresh water to cold water storage tank; (e) withdrawing a second proportion of the heated fresh water at a second temperature higher than the first temperature; (f) conveying the second proportion of the heated fresh water to a hot water storage tank.

Kaufmann, R.O.

1986-07-29T23:59:59.000Z

70

Heat recovery anti-icing system  

SciTech Connect

A heat recovery anti-icing system is disclosed. The heat recovery system includes a blower which removes air from the air flow path of a combustion turbine power generating system and circulates the air through a heat exchanger located in the exhaust stack of the combustion turbine. The heated air circulating through the heat exchanger is returned to an inlet filter compartment in the air flow path so as to maintain the temperature of the air in the inlet filter compartment at an elevated level.

Cummins, J.R.

1982-05-11T23:59:59.000Z

71

Heat Recovery From Solid Waste  

E-Print Network (OSTI)

More opportunity exists today for the successful implementation of resource recovery projects than at any other period. However, that doesn't mean that energy/resource recovery exists for everyone. You must have a favorable match of all the critical areas of evaluation, including the cost of fuel, cost of solid waste disposal, plant energy requirements, available technology, etc.

Underwood, O. W.

1981-01-01T23:59:59.000Z

72

Heat recovery in building envelopes  

E-Print Network (OSTI)

Heating Research Facility (AHHRF) located in Edmonton, Alberta, Canada. The house is of standard wood

Walker, Iain S.; Sherman, Max H.

2003-01-01T23:59:59.000Z

73

Property:Heat Recovery Utility | Open Energy Information  

Open Energy Info (EERE)

search Property Name Heat Recovery Utility Property Type Page Description The purpose of Distributed Generation heat recovery This is a property of type Page. Retrieved from...

74

Heat Pump for High School Heat Recovery  

E-Print Network (OSTI)

The heat pump system used for recycling and reusing waste heat in s high school bathroom was minutely analyzed in its coefficient of performance, onetime utilization ratio of energy, economic property and so on. The results showed that this system has good economic property, can conserve energy and protects the environment. Therefore, there is a large potential for its development. In addition, three projects using this system are presented and contrasted, which indicate that a joint system that uses both the heat pump and heat exchanger to recycle waste heat is a preferable option.

Huang, K.; Wang, H.; Zhou, X.

2006-01-01T23:59:59.000Z

75

Use Feedwater Economizers for Waste Heat Recovery  

SciTech Connect

This revised ITP tip sheet on feedwater economizers for waste heat recovery provides how-to advice for improving industrial steam systems using low-cost, proven practices and technologies.

2006-01-01T23:59:59.000Z

76

Heat Recovery Boilers for Process Applications  

E-Print Network (OSTI)

Heat recovery boilers are widely used in process plants for recovering energy from various waste gas streams, either from the consideration of process or of economy. Sulfuric, as well as nitric, acid plant heat recovery boilers are examples of the use of heat recovery due primarily to process considerations. On the other hand, cost and payback are main considerations in the case of gas turbine and incineration plants, where large quantities of gases are exhausted at temperatures varying from 800°F to 1800°F. This gas, when recovered, can result in a large energy savings and steam production. This paper attempts to outline some of the engineering considerations in the design of heat recovery boilers for turbine exhaust applications (combined cycle, cogeneration mode), incineration plants (solid waste, fume) and chemical plants (reformer, sulfuric acid, nitric acid).

Ganapathy, V.; Rentz, J.; Flanagan, D.

1985-05-01T23:59:59.000Z

77

Sound power and pressure level measurements in the inlet and outlet of an HRSG duct  

Science Conference Proceedings (OSTI)

The ever-increasing size of cogeneration facilities has mandated the need for noise abatement in the design stage. Many noise projection models are available to the industry for predicting noise levels in an adjacent to new installations. However, the models all require accurate source noise information if valid noise predictions are to be expected. As a consequence of designing one of the world`s largest cogeneration installations involving eight Model W-701 turbine units and their Heat Recovery Steam Generators (HRSGs), it became apparent that the attention between the exhaust of the Generators (HRSGs), it became apparent that the attention between the exhaust of the turbine and the outlet of the HRSGs was not well known. Not having this information posed potentially expensive noise abatement modifications during the design and construction phases. In order to verify the adequacy of scaling studies from a W-501 turbine and HRSG to the W-701 system, a comprehensive field test of an existing W-501 installation was conducted. This paper describes the design of an acoustic intensity and sound pressure probe to operate inside the high-temperature ductwork, the access engineering required, data acquisition, and final results concerning noise attenuation across the HRSG.

Jungbauer, D.E.; Unruh, J.F.; Pantermuehl, P.J. [Southwest Research Institute, San Antonio, TX (United States); Rose, S. [Enron Power Corp., Houston, TX (United States)

1995-04-01T23:59:59.000Z

78

Commercial laundry heat recovery system  

SciTech Connect

Waste water of above ambient temperature in a commercial laundry is directed through a self-cleaning plate and frame heat exchanger to heat incoming fresh water. Some of the fresh water heated to a first temperature is directed to a cold water storage tank to raise the water therein above ambient temperature which results in substantially lessened downstream requirements for heat input with commensurate cost reductions. The remainder of the fresh water is heated to a higher second temperature and is directed to a hot water storage tank. A system of valves regulates the temperature of the water flowing into each of the hot and cold water storage tanks to maintain a preset temperature in each of the storage tanks.

Kaufmann, R.O.

1983-02-15T23:59:59.000Z

79

Crude Distillation Unit Heat Recovery Study  

E-Print Network (OSTI)

Baytown's Pipe Still 3 is a 95,000 barrel per day crude distillation unit. A comprehensive heat recovery and energy utilization study was done on Pipe Still 3 after a preliminary cursory study had indicated that an overall look at the total picture could produce much better results than a series of improvements done piecemeal. The study did meet its objective by identifying the maximum heat recovery that is technically and economically feasible. It showed a potential for dramatic improvement - a 39 percent reduction in fuel, plus a 43 percent increase in the quantity of process steam generated, equivalent to a 48 percent reduction in net energy consumed. Techniques employed included a Source/Sink Profile (which is described later); a combining of oil heating, steam generation, and air preheat to best advantage; and a computer program to design the required heat exchanger trains.

John, P.

1979-01-01T23:59:59.000Z

80

Automatic flue gas heat recovery system  

Science Conference Proceedings (OSTI)

An automatic flue gas heat recovery system for supplementing or replacing a conventional, separate hot water system. In the example described, the heat recovery system is applied to a pizza restaurant where large quantities of heat energy are normally wasted up an oven chimney stack, and large quantities of hot water also are required for restaurant operations. An electric motor driven pump circulates water in a closed loop between a storage tank and a heat exchanger tube located in the oven chimney stack. A thermostat control automatically starts the pump when the oven heats the chimney stack to an effective water heating temperature. When temperature in the storage tank reaches a predetermined maximum, the thermostat control stops the pump, opens a drain valve, and dumps water quickly and completely from the heat exchanger tube. Three different embodiments are shown and described illustrating systems with one or more storage tanks and one or more pumps. In the plural storage tank embodiments, an existing hot water heating tank may be converted for use to augment a main tank supplied with the present system.

Whalen, D.A.

1983-02-22T23:59:59.000Z

Note: This page contains sample records for the topic "hrsg heat recovery" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Low Temperature Heat Recovery for Boiler Systems  

E-Print Network (OSTI)

Low temperature corrosion proof heat exchangers designed to reduce boiler flue gas temperatures to 150°F or lower are now being commercially operated on gas, oil and coal fired boilers. These heat exchangers, when applied to boiler flue gas, are commonly called condensing economizers. It has traditionally been common practice in the boiler industry to not reduce flue gas temperatures below the 300°F to 400°F range. This barrier has now been broken by the development and application of corrosion proof heat exchanger technology. This opens up a vast reservior of untapped recoverable energy that can be recovered and reused as an energy source. The successful recovery of this heat and the optimum use of it are the fundemental goals of the technology presented in this paper. This Recovered Low Level Heat Is Normally Used To Heat Cold Make-up Water Or Combustion Air.

Shook, J. R.; Luttenberger, D. B.

1986-06-01T23:59:59.000Z

82

Heat Recovery Design Considerations for Cogeneration Systems  

E-Print Network (OSTI)

The design and integration of the heat recovery section, which includes the steam generation, auxiliary firing, and steam turbine modules, is critical to the overall performance and economics of cogeneration, systems. In gas turbine topping cogeneration systems, over two-thirds of the energy is in the exhaust gases leaving the gas turbine. In bottoming cycles, where steam and/or electrical power are generated from heating process exhaust streams, the heat recovery design is of primary concern. John Zink Company, since 1929, has specialized in the development, design, and fabrication of energy efficient equipment for the industrial and commercial markets. The paper outlines the design, installation and performance of recently supplied gas turbine cogeneration heat recovery systems. It also describes; several bottoming cycle thermal system designs applied to incinerators, process heaters, refinery secondary reformers and FCC units. Overall parameters and general trends in the design and application of cogeneration thermal systems are presented. New equipment and system designs to reduce pollution and increase overall system efficiency are also reviewed.

Pasquinelli, D. M.; Burns, E. D.

1985-05-01T23:59:59.000Z

83

Teton Coin Op Laundry: heat recovery unit. Final report  

SciTech Connect

Experience with a heat recovery unit using Freon 11 refrigerant as a transfer medium is reported. Heat exchangers were fabricated for use in dryer stacks and the waste heat was used in heating the water for the laundry. (MHR)

1984-01-16T23:59:59.000Z

84

Heat Recovery Steam Generator Materials Selection Guideline  

Science Conference Proceedings (OSTI)

Materials selection is both an art and a science. There is no single material that is the optimal choice for a given application. For example, subtle changes such as the design, fabrication, and quality control specification for a high-pressure superheater (HPSH) tube-to-header connection can alter the choice of the optimal tube material. Minor changes to the component's operating environment can also alter the materials selection choice. What was an ideal tube material in a baseloaded heat recovery stea...

2011-12-21T23:59:59.000Z

85

Heat Recovery Steam Generator Procurement Specification  

Science Conference Proceedings (OSTI)

Many heat recovery steam generators (HRSGs), particularly those equipped with advanced gas turbines that are subjected to periods of frequent cyclic operation, have experienced premature pressure part failures resulting from excessive thermal mechanical fatigue damage. The very competitive power generation marketplace has resulted in the lowest installed cost often taking precedence over medium- and long-term durability and operating costs. The procurement of engineer, procure, and construct ...

2013-12-20T23:59:59.000Z

86

Heat recovery device for exhaust flues  

SciTech Connect

The heat recovery device has a flue pipe assembly including a section of standard flue pipe carrying a plurality of hollow, cylindrical heating tubes extending diametrically through the flue pipe section in axially spaced, parallel relationship and a separate housing defining an air flow chamber surrounding a portion of the flue pipe section. A fan inside the housing draws ambient air into the housing through an ambient air inlet located on the same side of the flue pipe assembly as the inlet of the heating tubes and propels a flow of air both through the heating tubes and over the outer surface of the flue pipe section towards a heated air outlet located on the same side of the flue pipe section as the discharge ends of the heating tubes. The flue pipe assembly is removably mounted on the housing so it can be removed in the event it fatigues and/or becomes plugged with carbon or creosote deposits during use. A thermostat on the flue pipe section turns the fan on and off when the temperature in the flue pipe section is respectively above and below a predetermined temperature. The total open area of the ambient air inlet and the heated air outlet is large enough so that, in the event the fan is inoperative, the natural flow of ambient air through the heating tubes and over the outer surface of the flue pipe is sufficient to prevent the flue pipe section from overheating.

Knoch, D. G.

1985-11-05T23:59:59.000Z

87

Design of Heat Exchanger for Heat Recovery in CHP Systems  

E-Print Network (OSTI)

The objective of this research is to review issues related to the design of heat recovery unit in Combined Heat and Power (CHP) systems. To meet specific needs of CHP systems, configurations can be altered to affect different factors of the design. Before the design process can begin, product specifications, such as steam or water pressures and temperatures, and equipment, such as absorption chillers and heat exchangers, need to be identified and defined. The Energy Engineering Laboratory of the Mechanical Engineering Department of the University of Louisiana at Lafayette and the Louisiana Industrial Assessment Center has been donated an 800kW diesel turbine and a 100 ton absorption chiller from industries. This equipment needs to be integrated with a heat exchanger to work as a Combined Heat and Power system for the University which will supplement the chilled water supply and electricity. The design constraints of the heat recovery unit are the specifications of the turbine and the chiller which cannot be altered.

Kozman, T. A.; Kaur, B.; Lee, J.

2009-05-01T23:59:59.000Z

88

Boiler Blowdown Heat Recovery Project Reduces Steam System Energy...  

NLE Websites -- All DOE Office Websites (Extended Search)

produced. Much of this heat can be recovered by routing the blown down liquid through a heat exchanger that preheats the boiler's makeup water. A boiler blowdown heat recovery...

89

Development and Application of Advanced Models for Steam Hydrogasification: Process Design and Economic Evaluation  

E-Print Network (OSTI)

Recovery Steam Generator (HRSG) to make additional steam foras electricity through HRSG and steam cycle in the steamof FT liquids distribution HRSG CO 2 capture Heat exchanger

Lu, Xiaoming

2012-01-01T23:59:59.000Z

90

Waste Heat Recovery Power Generation with WOWGen  

E-Print Network (OSTI)

WOW operates in the energy efficiency field- one of the fastest growing energy sectors in the world today. The two key products - WOWGen® and WOWClean® provide more energy at cheaper cost and lower emissions. •WOWGen® - Power Generation from Industrial Waste Heat •WOWClean® - Multi Pollutant emission control system. Current power generation technology uses only 35% of the energy in a fossil fuel and converts it to useful output. The remaining 65% is discharged into the environment as waste heat at temperatures ranging from 300°F to 1,200°F. This waste heat can be captured using the WOWGen® technology and turned into electricity. This efficiency is up to twice the rate of competing technologies. Compelling economics and current environmental policy are stimulating industry interest. WOWGen® power plants can generate between 1 - 25 MW of electricity. Project payback is between two to five years with IRR of 15% 30%. Nearly anywhere industrial waste heat is present, the WOW products can be applied. Beneficial applications of heat recovery power generation can be found in Industry (e.g. steel, glass, cement, lime, pulp and paper, refining and petrochemicals), Power Generation (CHP, biomass, biofuel, traditional fuels, gasifiers, diesel engines) and Natural Gas (pipeline compression stations, processing plants). Sources such as stack flue gases, steam, diesel exhaust, hot oil or combinations of sources can be used to generate power. WOWGen® can also be used with stand alone power plants burning fossil fuels or using renewable energy sources such as solar and biomass.

Romero, M.

2009-05-01T23:59:59.000Z

91

Bernd Blöbaum/Stefan Neuhaus (Hrsg.):  

Science Conference Proceedings (OSTI)

378 ßuchäesprerhungen. Bernd Blöbaum/Stefan Neuhaus (Hrsg.): Lite- ratur undjaurnalismus. Theorie, Kontexte, Fall- studien. — Wiesbaden: Westdeutscher

92

Wastewater heat recovery method and apparatus  

DOE Patents (OSTI)

This invention is comprised of a heat recovery system with a heat exchanger and a mixing valve. A drain trap includes a heat exchanger with an inner coiled tube, baffle plate, wastewater inlet, wastewater outlet, cold water inlet, and preheated water outlet. Wastewater enters the drain trap through the wastewater inlet, is slowed and spread by the baffle plate, and passes downward to the wastewater outlet. Cold water enters the inner tube through the cold water inlet and flows generally upward, taking on heat from the wastewater. This preheated water is fed to the mixing valve, which includes a flexible yoke to which are attached an adjustable steel rod, two stationary zinc rods, and a pivoting arm. The free end of the arm forms a pad which rests against a valve seat. The rods and pivoting arm expand or contract as the temperature of the incoming preheated water changes. The zinc rods expand more than the steel rod, flexing the yoke and rotating the pivoting arm. The pad moves towards the valve seat as the temperature of the preheated water rises, and away as the temperature falls, admitting a variable amount of hot water to maintain a nearly constant average process water temperature.

Kronberg, J.W.

1991-01-01T23:59:59.000Z

93

Waste Heat Recovery and Furnace Technology - Programmaster.org  

Science Conference Proceedings (OSTI)

Mar 5, 2013 ... Each source of waste heat is listed together with the assessment for potential cogeneration or direct recovery. The overall impact on energy ...

94

AHEX-A New, Combined Waste Heat Recovery and Emission ...  

Science Conference Proceedings (OSTI)

Presentation Title, AHEX-A New, Combined Waste Heat Recovery and Emission Control System for Anode Bake Furnaces. Author(s), Anders Kenneth Sorhuus, ...

95

Waste water heat recovery appliance. Final report  

SciTech Connect

An efficient convective waste heat recovery heat exchanger was designed and tested. The prototype appliance was designed for use in laundromats and other small commercial operations which use large amounts of hot water. Information on general characteristics of the coin-op laundry business, energy use in laundromats, energy saving resources already in use, and the potential market for energy saving devices in laundromats was collected through a literature search and interviews with local laundromat operators in Fort Collins, Colorado. A brief survey of time-use patterns in two local laundromats was conducted. The results were used, with additional information from interviews with owners, as the basis for the statistical model developed. Mathematical models for the advanced and conventional types were developed and the resulting computer program listed. Computer simulations were made using a variety of parameters; for example, different load profiles, hold-up volumes, wall resistances, and wall areas. The computer simulation results are discussed with regard to the overall conclusions. Various materials were explored for use in fabricating the appliance. Resistance to corrosion, workability, and overall suitability for laundromat installations were considered for each material.

Chapin, H.D.; Armstrong, P.R.; Chapin, F.A.W.

1983-11-21T23:59:59.000Z

96

List of Heat recovery Incentives | Open Energy Information  

Open Energy Info (EERE)

recovery Incentives recovery Incentives Jump to: navigation, search The following contains the list of 174 Heat recovery Incentives. CSV (rows 1 - 174) Incentive Incentive Type Place Applicable Sector Eligible Technologies Active AEP Ohio - Commercial Custom Project Rebate Program (Ohio) Utility Rebate Program Ohio Commercial Fed. Government Industrial Institutional Local Government Nonprofit Schools State Government Tribal Government Boilers Central Air conditioners Chillers Custom/Others pending approval Furnaces Heat pumps Heat recovery Lighting Lighting Controls/Sensors Processing and Manufacturing Equipment Refrigerators Yes AEP Ohio - Commercial Self Direct Rebate Program (Ohio) Utility Rebate Program Ohio Commercial Fed. Government Industrial Institutional Local Government

97

Combined heat recovery and make-up water heating system  

Science Conference Proceedings (OSTI)

A cogeneration plant is described comprising in combination: a first stage source of hot gas; a duct having an inlet for receiving the hot gas and an outlet stack open to the atmosphere; a second stage recovery heat steam generator including an evaporator situated in the duct, and economizer in the duct downstream of the evaporator, and steam drum fluidly connected to the evaporator and the economizer; feedwater supply means including a deaerator heater and feedwater pump for supplying deaerated feedwater to the steam drum through the economizer; makeup water supply means including a makeup pump for delivering makeup water to the deaerator heater; means fluidly connected to the steam drum for supplying auxiliary steam to the deaerator heater; and heat exchanger means located between the deaerator and the economizer, for transferring heat from the feedwater to the makeup water, thereby increasing the temperature of the makeup water delivered to the deaerator and decreasing the temperature of the feedwater delivered to the economizer, without fluid exchange.

Kim, S.Y.

1988-05-24T23:59:59.000Z

98

Design of heat-recovery and seed-recovery units in MHD power generation  

DOE Green Energy (OSTI)

Crucial and limiting engineering and materials problems associated with the design of an MHD steam bottoming plant are discussed. Existing experimental and theoretical results on corrosion, fouling and deposits, potassium seed recovery and regeneration, are reviewed. The state of knowledge regarding the design of heat recovery and seed recovery units for coal-fired MHD plants is inadequate at the present time.

Bergman, P.D.; Joubert, J.I.; Demski, R.J.; Bienstock, D.

1974-01-01T23:59:59.000Z

99

Distributed Generation with Heat Recovery and Storage  

E-Print Network (OSTI)

Energy; Grid systems; Optimization; Heat flow; Financialof grid power and by utilizing combined heat and power (CHP)

Siddiqui, Afzal S.; Marnay, Chris; Firestone, Ryan M.; Zhou, Nan

2008-01-01T23:59:59.000Z

100

Waste Heat Recovery System: Lightweight Thermal Energy Recovery (LIGHTER) System  

SciTech Connect

Broad Funding Opportunity Announcement Project: GM is using shape memory alloys that require as little as a 10°C temperature difference to convert low-grade waste heat into mechanical energy. When a stretched wire made of shape memory alloy is heated, it shrinks back to its pre-stretched length. When the wire cools back down, it becomes more pliable and can revert to its original stretched shape. This expansion and contraction can be used directly as mechanical energy output or used to drive an electric generator. Shape memory alloy heat engines have been around for decades, but the few devices that engineers have built were too complex, required fluid baths, and had insufficient cycle life for practical use. GM is working to create a prototype that is practical for commercial applications and capable of operating with either air- or fluid-based heat sources. GM’s shape memory alloy based heat engine is also designed for use in a variety of non-vehicle applications. For example, it can be used to harvest non-vehicle heat sources, such as domestic and industrial waste heat and natural geothermal heat, and in HVAC systems and generators.

2010-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "hrsg heat recovery" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Apparatus for recovery of heat from exhaust gases of dryer  

SciTech Connect

Apparatus and method are disclosed for recovery of heat from exhaust gases of dryers and return of heat to the dryer system. Fresh air is drawn through a plurality of tubes in heat exchange relation to heated exhaust gases and introduced into the drying system without intermingling of contaminated exhaust gases with the heated fresh air. The apparatus and method have particular utility in gas-fired commercial and industrial laundry dryers.

Winstel, F.H.

1977-06-14T23:59:59.000Z

102

CFD Simulation of Infiltration Heat Recovery  

E-Print Network (OSTI)

Nomenclature Cp= specific heat capacity of air (1006 J/kg K) CP,= specific heat capacity of insulation solidJ/kg K) CPW specific heat capacity of wall sheathing (1200

Buchanan, C.R.

2011-01-01T23:59:59.000Z

103

Distributed Generation with Heat Recovery and Storage  

E-Print Network (OSTI)

Doubling combined heat and power capacity in the UnitedCost Savings from Heat Storage Capacity Figure 49. LargeR 2 = 0.6683 Heat Storage Capacity (kWh) Fig. 48 Weekday

Siddiqui, Afzal S.; Marnay, Chris; Firestone, Ryan M.; Zhou, Nan

2008-01-01T23:59:59.000Z

104

Distributed Generation with Heat Recovery and Storage  

E-Print Network (OSTI)

between heat storage costs and capacity can be determineda given kWh of heat storage capacity is worth to a typicalequation (22) sets the heat storage capacity to the maximum

Siddiqui, Afzal; Marnay, Chris; Firestone, Ryan M.; Zhou, Nan

2005-01-01T23:59:59.000Z

105

Distributed Generation with Heat Recovery and Storage  

E-Print Network (OSTI)

of electricity and natural gas DER No Heat Storage: thefired natural gas AC (a) Capacity of heat storage unit (but no heat storage, a 200 kW natural gas reciprocating

Siddiqui, Afzal; Marnay, Chris; Firestone, Ryan M.; Zhou, Nan

2005-01-01T23:59:59.000Z

106

Distributed Generation with Heat Recovery and Storage  

E-Print Network (OSTI)

of electricity and natural gas DER No Heat Storage: therecovery and storage) utility electricity and natural gasbut no heat storage, a 200 kW natural gas reciprocating

Siddiqui, Afzal S.; Marnay, Chris; Firestone, Ryan M.; Zhou, Nan

2008-01-01T23:59:59.000Z

107

RANKINE CYCLE WASTE HEAT RECOVERY SYSTEM - Energy Innovation Portal  

This disclosure relates to a waste heat recovery (WHR) system and to a system and method for regulation of a fluid inventory in a condenser and a receiver of a ...

108

Open-loop heat-recovery dryer  

DOE Patents (OSTI)

A drying apparatus is disclosed that includes a drum and an open-loop airflow pathway originating at an ambient air inlet, passing through the drum, and terminating at an exhaust outlet. A passive heat exchanger is included for passively transferring heat from air flowing from the drum toward the exhaust outlet to air flowing from the ambient air inlet toward the drum. A heat pump is also included for actively transferring heat from air flowing from the passive heat exchanger toward the exhaust outlet to air flowing from the passive heat exchanger toward the drum. A heating element is also included for further heating air flowing from the heat pump toward the drum.

TeGrotenhuis, Ward Evan

2013-11-05T23:59:59.000Z

109

Waste Heat Recovery in Industrial Facilities  

Science Conference Proceedings (OSTI)

Low-temperature waste heat streams account for the majority of the industrial waste heat inventory. With a reference temperature of 60°F (16°C), 65% of the waste heat is below 450°F (232°C) and 99% is below 1,200°F (649°C). With a reference temperature of 300°F (149°C), 14% of the waste heat is below 450°F, and 96% is below 1,200°F. Waste heat is concentrated in a few industrial manufacturing sectors. Based on a review of 21 manufacturing sectors, the top two sectors that produce waste heat are petroleu...

2010-12-20T23:59:59.000Z

110

Guidelines on Optimizing Heat Recovery Steam Generator Drains  

Science Conference Proceedings (OSTI)

Severe thermal-mechanical fatigue damage to the superheaters (SHs), reheaters (RHs), and steam piping of horizontal-gas-path heat recovery steam generators due primarily to ineffective drainage of the condensate that is generated in superheaters and reheaters at every startup continues to be a significant industry problem that results in avoidable deterioration of unit reliability and significant unnecessary maintenance costs. This report will assist operators in guiding heat recovery steam generator (HR...

2007-12-21T23:59:59.000Z

111

Field Guide: Heat Recovery Steam Generator Outage Inspection Pocket Manual  

Science Conference Proceedings (OSTI)

Heat recovery steam generators (HRSGs) pose a unique set of operational challenges, due in part to their rapid startup capabilities and high operating efficiencies. Among these challenges are the difficulty of inspection and repair, which are complicated by limited access as well as the complexity of the equipment. To help members address these challenges, the Electric Power Research Institute's (EPRI's) Heat Recovery Steam Generator Dependability program has added this field guide to its comprehensive s...

2010-12-23T23:59:59.000Z

112

Minewater heat recovery project. Final Technical report  

DOE Green Energy (OSTI)

This report consists of three sections: (1) Design, experimental testing and performance analysis of the 20-ft long DBHE (Downhole Bundle Heat Exchanger); (2) Modified design of mine water heat exchanger; and (3) Performance tests on mine water heat exchanger. Appendices summarize design calculations, discuss the scope of the work tasks, and present a diary of the progress throughout the research and development project.

NONE

1992-04-01T23:59:59.000Z

113

Heat recovery in a laundry system  

SciTech Connect

In a laundry system including a washer, a dryer, and a water heater, improvement is disclosed of using a heat pipe to recover waste heat, whether it be from the hot air exhaust of the dryer or from the conductive losses from the dryer and to transfer that heat to the feed water of the water heater.

George, O.F.

1981-06-30T23:59:59.000Z

114

Cascade heat recovery with coproduct gas production  

DOE Patents (OSTI)

A process for the integration of a chemical absorption separation of oxygen and nitrogen from air with a combustion process is set forth wherein excess temperature availability from the combustion process is more effectively utilized to desorb oxygen product from the absorbent and then the sensible heat and absorption reaction heat is further utilized to produce a high temperature process stream. The oxygen may be utilized to enrich the combustion process wherein the high temperature heat for desorption is conducted in a heat exchange preferably performed with a pressure differential of less than 10 atmospheres which provides considerable flexibility in the heat exchange. 4 figs.

Brown, W.R.; Cassano, A.A.; Dunbobbin, B.R.; Rao, P.; Erickson, D.C.

1986-10-14T23:59:59.000Z

115

Cascade heat recovery with coproduct gas production  

DOE Patents (OSTI)

A process for the integration of a chemical absorption separation of oxygen and nitrogen from air with a combustion process is set forth wherein excess temperature availability from the combustion process is more effectively utilized to desorb oxygen product from the absorbent and then the sensible heat and absorption reaction heat is further utilized to produce a high temperature process stream. The oxygen may be utilized to enrich the combustion process wherein the high temperature heat for desorption is conducted in a heat exchange preferably performed with a pressure differential of less than 10 atmospheres which provides considerable flexibility in the heat exchange.

Brown, William R. (Zionsville, PA); Cassano, Anthony A. (Allentown, PA); Dunbobbin, Brian R. (Allentown, PA); Rao, Pradip (Allentown, PA); Erickson, Donald C. (Annapolis, MD)

1986-01-01T23:59:59.000Z

116

Distributed Generation with Heat Recovery and Storage  

E-Print Network (OSTI)

selection of on-site power generation with combined heat andsingle-cycle thermal power generation is typically lesshighly centralized power generation and delivery system

Siddiqui, Afzal S.; Marnay, Chris; Firestone, Ryan M.; Zhou, Nan

2008-01-01T23:59:59.000Z

117

Distributed Generation with Heat Recovery and Storage  

E-Print Network (OSTI)

involved, supplemental absorption cooling allows downsizingwater heating and for absorption cooling) in a day SHPricedisplaced by absorption cooling. The same principle applies

Siddiqui, Afzal S.; Marnay, Chris; Firestone, Ryan M.; Zhou, Nan

2008-01-01T23:59:59.000Z

118

Application Research of Evaporative Cooling in the Waste Heat Recovery  

Science Conference Proceedings (OSTI)

Evaporative condenser is one kind of high-efficient and energy-water saving heat exchange equipment, which has been widely applied in many engineering fields. The theory and product characteristic of evaporative condenser is introduced in this paper. ... Keywords: Evaporative condenser, Waste heat recovery, Energy saving, Water saving

Zhijiang Wu; Nan Wang; Gongsheng Zhu

2010-12-01T23:59:59.000Z

119

Direct Refrigeration from Heat Recovery Using 2-Stage Absorption Chillers  

E-Print Network (OSTI)

Although the cost of some fossil fuels has moderated, the importance of energy conservation by heat recovery has not diminished. The application of waste heat generated steam to produce chilled water is not new. However, there is a newly developed absorption chiller which can produce chilled water 44% more efficiently than the conventional single stage absorption chillers. The new 2-stage parallel flow system makes the chiller package more compact, more efficient, and easier to operate. Many types of waste heat, not just steam, can be used directly in this new chiller without the need for costly recovery and conversion systems.

Hufford, P. E.

1983-01-01T23:59:59.000Z

120

Mobile power plants : waste body heat recovery  

E-Print Network (OSTI)

Novel methods to convert waste metabolic heat into useful and useable amounts of electricity were studied. Thermoelectric, magneto hydrodynamic, and piezo-electric energy conversions at the desired scope were evaluated to ...

Gibbons, Jonathan S. (Jonathan Scott), 1979-

2004-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "hrsg heat recovery" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Use of photovoltaics for waste heat recovery  

DOE Patents (OSTI)

A device for recovering waste heat in the form of radiated light, e.g. red visible light and/or infrared light includes a housing having a viewing window, and a photovoltaic cell mounted in the housing in a relationship to the viewing window, wherein rays of radiated light pass through the viewing window and impinge on surface of the photovoltaic cell. The housing and/or the cell are cooled so that the device can be used with a furnace for an industrial process, e.g. mounting the device with a view of the interior of the heating chamber of a glass making furnace. In this manner, the rays of the radiated light generated during the melting of glass batch materials in the heating chamber pass through the viewing window and impinge on the surface of the photovoltaic cells to generate electric current which is passed onto an electric load.

Polcyn, Adam D

2013-04-16T23:59:59.000Z

122

Property:Heat Recovery Systems | Open Energy Information  

Open Energy Info (EERE)

Systems Systems Jump to: navigation, search Property Name Heat Recovery Systems Property Type Page Description Distributed Data heat recovery systems Pages using the property "Heat Recovery Systems" Showing 25 pages using this property. (previous 25) (next 25) C Capstone C30 + Unifin + Capstone C60 + Unifin HX + D Distributed Generation Study/10 West 66th Street Corp + Built-in + Distributed Generation Study/615 kW Waukesha Packaged System + Sondex PHE-Type SL140-TM-EE-190 +, Sondex PHE-Type SL140-TM-EE-150 +, Cain UTR1-810A17.5SSP + Distributed Generation Study/Aisin Seiki G60 at Hooligans Bar and Grille + Built-in + Distributed Generation Study/Arrow Linen + Built-in + Distributed Generation Study/Dakota Station (Minnegasco) + Unifin + Distributed Generation Study/Elgin Community College + Beaird Maxim Model TRP-12 +

123

Advanced heat pump for the recovery of volatile organic compounds  

Science Conference Proceedings (OSTI)

Emissions of Volatile Organic Compounds (VOC) from stationary industrial and commercial sources represent a substantial portion of the total US VOC emissions. The Toxic-Release Inventory'' of The US Environmental Protection Agency estimates this to be at about 3 billion pounds per year (1987 estimates). The majority of these VOC emissions are from coating processes, cleaning processes, polymer production, fuel production and distribution, foam blowing,refrigerant production, and wood products production. The US Department of Energy's (DOE) interest in the recovery of VOC stems from the energy embodied in the recovered solvents and the energy required to dispose of them in an environmentally acceptable manner. This Phase I report documents 3M's work in close working relationship with its subcontractor Nuclear Consulting Services (Nucon) for the preliminary conceptual design of an advanced Brayton cycle heat pump for the recovery of VOC. Nucon designed Brayton cycle heat pump for the recovery of methyl ethyl ketone and toluene from coating operations at 3M Weatherford, OK, was used as a base line for the work under cooperative agreement between 3M and ODE. See appendix A and reference (4) by Kovach of Nucon. This cooperative agreement report evaluates and compares an advanced Brayton cycle heat pump for solvent recovery with other competing technologies for solvent recovery and reuse. This advanced Brayton cycle heat pump is simple (very few components), highly reliable (off the shelf components), energy efficient and economically priced.

Not Available

1992-03-01T23:59:59.000Z

124

Distributed Generation with Heat Recovery and Storage  

DOE Green Energy (OSTI)

Electricity generated by distributed energy resources (DER) located close to end-use loads has the potential to meet consumer requirements more efficiently than the existing centralized grid. Installation of DER allows consumers to circumvent the costs associated with transmission congestion and other non-energy costs of electricity delivery and potentially to take advantage of market opportunities to purchase energy when attractive. On-site thermal power generation is typically less efficient than central station generation, but by avoiding non-fuel costs of grid power and utilizing combined heat and power (CHP) applications, i.e., recovering heat from small-scale on-site generation to displace fuel purchases, then DER can become attractive to a strictly cost-minimizing consumer. In previous efforts, the decisions facing typical commercial consumers have been addressed using a mixed-integer linear programme, the DER Customer Adoption Model(DER-CAM). Given the site s energy loads, utility tariff structure, and information (both technical and financial) on candidate DER technologies, DER-CAM minimizes the overall energy cost for a test year by selecting the units to install and determining their hourly operating schedules. In this paper, the capabilities of DER-CAM are enhanced by the inclusion of the option to store recovered low-grade heat. By being able to keep an inventory of heat for use in subsequent periods, sites are able to lower costs even further by reducing off-peak generation and relying on storage. This and other effects of storages are demonstrated by analysis of five typical commercial buildings in San Francisco, California, and an estimate of the cost per unit capacity of heat storage is calculated.

Siddiqui, Afzal; Marnay, Chris; Firestone, Ryan M.; Zhou, Nan

2005-07-29T23:59:59.000Z

125

Distributed Generation with Heat Recovery and Storage  

SciTech Connect

Electricity produced by distributed energy resources (DER)located close to end-use loads has the potential to meet consumerrequirements more efficiently than the existing centralized grid.Installation of DER allows consumers to circumvent the costs associatedwith transmission congestion and other non-energy costs of electricitydelivery and potentially to take advantage of market opportunities topurchase energy when attractive. On-site, single-cycle thermal powergeneration is typically less efficient than central station generation,but by avoiding non-fuel costs of grid power and by utilizing combinedheat and power (CHP) applications, i.e., recovering heat from small-scaleon-site thermal generation to displace fuel purchases, DER can becomeattractive to a strictly cost-minimizing consumer. In previous efforts,the decisions facing typical commercial consumers have been addressedusing a mixed-integer linear program, the DER Customer Adoption Model(DER-CAM). Given the site s energy loads, utility tariff structure, andinformation (both technical and financial) on candidate DER technologies,DER-CAM minimizes the overall energy cost for a test year by selectingthe units to install and determining their hourly operating schedules. Inthis paper, the capabilities of DER-CAM are enhanced by the inclusion ofthe option to store recovered low-grade heat. By being able to keep aninventory of heat for use in subsequent periods, sites are able to lowercosts even further by reducing lucrative peak-shaving generation whilerelying on storage to meet heat loads. This and other effects of storageare demonstrated by analysis of five typical commercial buildings in SanFrancisco, California, USA, and an estimate of the cost per unit capacityof heat storage is calculated.

Siddiqui, Afzal S.; Marnay, Chris; Firestone, Ryan M.; Zhou, Nan

2006-06-16T23:59:59.000Z

126

Waste Heat Recovery from Refrigeration in a Meat Processing Facility  

E-Print Network (OSTI)

A case study is reviewed on a heat recovery system installed in a meat processing facility to preheat water for the plant hot water supply. The system utilizes waste superheat from the facility's 1,350-ton ammonia refrigeration system. The heat recovery system consists of a shell and tube heat exchanger (16"? x 14'0") installed in the compressor hot gas discharge line. Water is recirculated from a 23,000-gallon tempered water storage tank to the heat exchanger by a circulating pump at the rate of 100 gallons per minute. All make-up water to the plant hot water system is supplied from this tempered water storage tank, which is maintained at a constant filled level. Tests to determine the actual rate of heat recovery were conducted from October 3, 1979 to October 12, 1979, disclosing an average usage of 147,000 gallons of hot water daily. These tests illustrated a varied heat recovery of from 0.5 to 1.0 million BTU per hour. The deviations were the result of both changing refrigeration demands and compressor operating modes. An average of 16 million BTU per day was realized, resulting in reduced boiler fuel costs of $30,000 annually, based on the present $.80 per gallon #2 fuel oil price. At the total installed cost of $79,000, including test instrumentation, the project was found to be economically viable. The study has demonstrated the technical and economic feasibility of refrigeration waste heat recovery as a positive energy conservation strategy which has broad applications in industry and commerce.

Murphy, W. T.; Woods, B. E.; Gerdes, J. E.

1980-01-01T23:59:59.000Z

127

Waste Heat Recovery – Submerged Arc Furnaces (SAF)  

E-Print Network (OSTI)

Submerged Arc Furnaces are used to produce high temperature alloys. These furnaces typically run at 3000°F using high voltage electricity along with metallurgical carbon to reduce metal oxides to pure elemental form. The process as currently designed consumes power and fuel that yields an energy efficiency of approximately 40% (Total Btu’s required to reduce to elemental form/ Btu Input). The vast majority of heat is lost to the atmosphere or cooling water system. The furnaces can be modified to recover this heat and convert it to power. The system will then reduce the amount of purchased power by approximately 25% without any additional use of fuel. The cost of this power is virtually unchanged over the life of the project because of the use of capital to displace fuel consumed from the purchased power source.

O'Brien, T.

2008-01-01T23:59:59.000Z

128

Heat Recovery Considerations for Process Heaters and Boilers  

E-Print Network (OSTI)

The largest single area for industrial energy conservation is in the improvement of combustion efficiencies for heaters and boilers. A number of methods can be employed to recover heat. The most common are by use of recuperative air preheaters, regenerative air preheaters and economizers. Relative advantages and applicability of the three methods are discussed. Analytical methods and correlations are presented which enable determination of size of unit, capital cost and operating cost for each of the three methods of heat recovery.

Kumar, A.

1982-01-01T23:59:59.000Z

129

Heat Recovery Consideration for Process Heaters and Boilers  

E-Print Network (OSTI)

The largest single area for industrial energy conservation is in the improvement of combustion efficiencies for heaters and boilers. A number of methods can be employed to recover heat. The most common are by use of recuperative air preheaters, regenerative air preheaters and economizers. Relative advantages and applicability of the three methods are discussed. Analytical methods and correlations are presented which enable determination of size of unit, capital cost and operating cost for each of the three methods of heat recovery.

Kumar, A.

1984-01-01T23:59:59.000Z

130

Heat Recovery Considerations for Process Heaters and Boilers  

E-Print Network (OSTI)

The largest single area for industrial energy conservation is in the improvement of combustion efficiencies for heaters and boilers. A number of methods can be employed to recover heat. The most common are by use of recuperative air preheaters, regenerative air preheaters and economizers. Relative advantages and applicability of the three methods are discussed. Analytical methods and correlations are presented which enable determination of size of unit, capital cost and operating cost for each of the three methods of heat recovery.

Kumar, A.

1985-05-01T23:59:59.000Z

131

Heat Recovery Considerations for Process Heaters and Boilers  

E-Print Network (OSTI)

The largest single area for industrial energy conservation is in the improvement of combustion efficiencies for heaters and boilers. A number of methods can be employed to recover heat. The most common are by use of recuperative air preheaters, regenerative air preheaters and economizers. Relative advantages and applicability of the three methods are discussed. Analytical methods and correlations are presented which enable determination of size and unit, capital cost and operating cost for each of the three methods of heat recovery.

Kumar, A.

1986-06-01T23:59:59.000Z

132

Heat Recovery Consideration for Process Heaters and Boilers  

E-Print Network (OSTI)

The largest single area for industrial energy conservation is in the improvement of combustion efficiencies for heaters and boilers. A number of methods can be employed to recover heat. The most common are by use of recuperative air preheaters, regenerative air preheaters and economizers. Relative advantages and applicability of the three methods are discussed. Analytical methods and correlations are presented which enable determination of size of unit, capital cost and operating cost for each of the three methods of heat recovery.

Kumar, A.

1983-01-01T23:59:59.000Z

133

Heat recovery and seed recovery development project: preliminary design report (PDR)  

DOE Green Energy (OSTI)

The preliminary design and performance characteristics are described of the 20 MWt heat recovery and seed recovery (HRSR) system to be fabricated, installed, and evaluated to provide a technological basis for the design of commercial size HRSR systems for coal-fired open-cycle MHD power plants. The system description and heat and material balances, equipment description and functional requirements, controls, interfacing systems, and operation and maintenance are detailed. Appendices include: (1) recommended environmental requirements for compliance with federal and state of Tennessee regulations, (2) channel and diffuser simulator, (3) equipment arrangement drawings, and (4) channel and diffuser simulator barrel drawings. (WHK)

Arkett, A. H.; Alexander, K. C.; Bolek, A. D.; Blackman, B. K.; Kurrle, P. E.; Tram, S. V.; Warren, A. M.; Ziobrowski, A. J.

1981-06-01T23:59:59.000Z

134

High temperature heat pipes for waste heat recovery  

SciTech Connect

Operation of heat pipes in air at temperatures above 1200/sup 0/K has been accomplished using SiC as a shell material and a chemical vapor deposit (CVD) tungsten inner liner for protection of the ceramic from the sodium working fluid. The CVD tungsten has been used as a distribution wick for the gravity assisted heat pipe through the development of a columnar tungsten surface structure, achieved by control of the metal vapor deposition rate. Wick performance has been demonstrated in tests at approximately 2 kW throughput with a 19-mm-i.d. SiC heat pipe. Operation of ceramic heat pipes in repeated start cycle tests has demonstrated their ability to withstand temperature rise rates of greater than 1.2 K/s.

Merrigan, M.A.; Keddy, E.S.

1980-01-01T23:59:59.000Z

135

Waste Heat Recovery From Stacks Using Direct-Contact Condensing Heat Exchange  

E-Print Network (OSTI)

Flue gases exiting the stack of a boiler create thermal losses normally amounting to 15 to 20 percent of the high heating value of the fuel fired. By capturing and using this lost energy using condensing heat recovery, the overall efficiency of the system can be raised to over 95 percent. This paper reviews the origins of stack heat losses, direct contact condensing heat recovery processes, the Rocket Research Company CON-X condensing recuperator equipment and systems, site specific case studies and fuels and condensate acidity. A detailed example of the determination of the magnitude of stack heat losses is presented along with a methodology for the reader to make a preliminary heat recovery evaluation.

Thorn, W. F.

1986-06-01T23:59:59.000Z

136

Method for controlling exhaust gas heat recovery systems in vehicles  

DOE Patents (OSTI)

A method of operating a vehicle including an engine, a transmission, an exhaust gas heat recovery (EGHR) heat exchanger, and an oil-to-water heat exchanger providing selective heat-exchange communication between the engine and transmission. The method includes controlling a two-way valve, which is configured to be set to one of an engine position and a transmission position. The engine position allows heat-exchange communication between the EGHR heat exchanger and the engine, but does not allow heat-exchange communication between the EGHR heat exchanger and the oil-to-water heat exchanger. The transmission position allows heat-exchange communication between the EGHR heat exchanger, the oil-to-water heat exchanger, and the engine. The method also includes monitoring an ambient air temperature and comparing the monitored ambient air temperature to a predetermined cold ambient temperature. If the monitored ambient air temperature is greater than the predetermined cold ambient temperature, the two-way valve is set to the transmission position.

Spohn, Brian L.; Claypole, George M.; Starr, Richard D

2013-06-11T23:59:59.000Z

137

Brayton Solvent Recovery Heat Pump Technology Update  

E-Print Network (OSTI)

The Brayton cycle technology was developed to reduce the temperature of gas streams containing solvents in order to condense and recover them. While the use of turbo compressor/expander machinery in conjunction with an energy recuperator is the basis for this heat pump process, many variations can be incorporated to optimize the total process for specific applications. Several process schemes will be discussed including both direct condensation and adsorption approaches. For situations where the solvent is at a relatively high concentration, such as tank filling operations, the direct condensation system is chosen. If the concentrations are low, which would be the case for an oven drying operation, activated carbon beds are used to concentrate the solvent. Many improvements on the first generation designs have been made in both process and the equipment components used for various commercial installations. Several specific applications have been identified as being well suited to take advantage of the features of this type of equipment.

Enneking, J. C.

1993-03-01T23:59:59.000Z

138

Water recovery using waste heat from coal fired power plants.  

Science Conference Proceedings (OSTI)

The potential to treat non-traditional water sources using power plant waste heat in conjunction with membrane distillation is assessed. Researchers and power plant designers continue to search for ways to use that waste heat from Rankine cycle power plants to recover water thereby reducing water net water consumption. Unfortunately, waste heat from a power plant is of poor quality. Membrane distillation (MD) systems may be a technology that can use the low temperature waste heat (<100 F) to treat water. By their nature, they operate at low temperature and usually low pressure. This study investigates the use of MD to recover water from typical power plants. It looks at recovery from three heat producing locations (boiler blow down, steam diverted from bleed streams, and the cooling water system) within a power plant, providing process sketches, heat and material balances and equipment sizing for recovery schemes using MD for each of these locations. It also provides insight into life cycle cost tradeoffs between power production and incremental capital costs.

Webb, Stephen W.; Morrow, Charles W.; Altman, Susan Jeanne; Dwyer, Brian P.

2011-01-01T23:59:59.000Z

139

Retrofits for Improved Heat Rate and Availability: Circulating Water Heat Recovery Retrofits  

Science Conference Proceedings (OSTI)

Circulating water heat recovery is a means of directly increasing the thermal efficiency of a power plant. If only fuel savings are considered, the economic benefit is often only marginal. However, when increased megawatt output and heat-rate improvements are included in the economic analysis, such retrofits can be attractive, with break-even fuel costs sometimes approaching $1/million Btu.

1990-11-20T23:59:59.000Z

140

Total Energy Recovery System for Agribusiness. [Geothermally heated]. Final Report  

DOE Green Energy (OSTI)

An engineering and economic study was made to determine a practical balance of selected agribusiness subsystems resulting in realistic estimated produce yields for a geothermally heated system known as the Total Energy Recovery System for Agribusiness. The subsystem cycles for an average application at an unspecified hydrothermal resources site in the western United States utilize waste and by-products from their companion cycles insofar as practicable. Based on conservative estimates of current controlled environment yields, produce wholesale market prices, production costs, and capital investment required, it appears that the family-operation-sized TERSA module presents the potential for marginal recovery of all capital investment costs. In addition to family- or small-cooperative-farming groups, TERSA has potential users in food-oriented corporations and large-cooperative-agribusiness operations. The following topics are considered in detail: greenhouse tomatoes and cucumbers; fish farming; mushroom culture; biogas generation; integration methodology; hydrothermal fluids and heat exchanger selection; and the system. 133 references. (MHR)

Fogleman, S.F.; Fisher, L.A.; Black, A.R.; Singh, D.P.

1977-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "hrsg heat recovery" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Cogeneration Waste Heat Recovery at a Coke Calcining Facility  

E-Print Network (OSTI)

PSE Inc. recently completed the design, construction and start-up of a cogeneration plant in which waste heat in the high temperature flue gases of three existing coke calcining kilns is recovered to produce process steam and electrical energy. The heat previously exhausted to the atmosphere is now converted to steam by waste heat recovery boilers. Eighty percent of the steam produced is metered for sale to a major oil refinery, while the remainder passes through a steam turbine generator and is used for deaeration and feedwater heating. The electricity produced is used for the plant auxiliaries and sold to the local utility. Many design concepts were incorporated into the plant which provided for high plant availability, reliability and energy efficiency. This paper will show how these concepts were implemented and incorporated into the detailed design of the plant while making cogeneration a cost effective way to save conventional fuels. Operating data since plant start-up will also be presented.

Coles, R. L.

1986-06-01T23:59:59.000Z

142

Repair Welding Technologies For Heat Recovery Steam Generators  

Science Conference Proceedings (OSTI)

Tube failures that occur in heat recovery steam generators (HRSGs) are often caused by thermal stress or thermal shock associated with cyclic plant operation or by flow-accelerated corrosion. Many premature failures occur along the length of finned tubes or at attachment locations where tubes are joined to the upper or lower header. Because of current tube repair practices and limited access for welding, reoccurring failures are common.

2005-12-21T23:59:59.000Z

143

Waste Heat Recovery by Organic Fluid Rankine Cycle  

E-Print Network (OSTI)

The use of Organic Rankine Cycle for waste heat recovery presents several characteristics which are analyzed in details. After a short comparison with steam cycles, the Organic Rankine Cycle is described : its simplicity is shown and achievable efficiencies versus heat source temperature are given. Available fluids are presented. The choice of the fluid allows a good adaptation to temperature and power for each application. The most interesting field for Organic Rankine Cycles are low mechanical powers of a few megawatts and medium temperatures, about 500 C/600 C, for flue gas. The very simple technology of turbines is shown. Three examples are presented. The first one is a test loop of 300 thermal kW built in BERTIN & Cie laboratory to experiment a supersonic turbine designed by the same company for organic vapor at 250 C. The second gives the main characteristics of recovery from exhaust gas of Diesel engines. The last deals with possible recovery from air quenching of clinker in cement plants.

Verneau, A.

1979-01-01T23:59:59.000Z

144

Recent HRSG projects at Nooter/Eriksen  

Science Conference Proceedings (OSTI)

As demand for combined-cycle power plants continues to grow throughout many parts of the world, Nooter/Eriksen, headquartered in St. Louis, Missouri, U.S.A., has played a leading role in supplying natural circulation heat recovery steam generators (HRSGs) for many high-profile projects. In the U.K., where the company established Nooter/Eriksen Ltd. in 1990, two HRSGs were recently commissioned as part of the Medway power station located on the Isle of Grain in Kent. The Medway project followed closely the company`s successful experience with several HRSGs at the Teesside, England, power station. This article describes in brief the highlights of the project.

McNeely, M.

1996-10-01T23:59:59.000Z

145

Building Technologies Office: Recovery Act-Funded Ground Source Heat Pump  

NLE Websites -- All DOE Office Websites (Extended Search)

Ground Source Heat Pump Demonstration Projects to someone by E-mail Ground Source Heat Pump Demonstration Projects to someone by E-mail Share Building Technologies Office: Recovery Act-Funded Ground Source Heat Pump Demonstration Projects on Facebook Tweet about Building Technologies Office: Recovery Act-Funded Ground Source Heat Pump Demonstration Projects on Twitter Bookmark Building Technologies Office: Recovery Act-Funded Ground Source Heat Pump Demonstration Projects on Google Bookmark Building Technologies Office: Recovery Act-Funded Ground Source Heat Pump Demonstration Projects on Delicious Rank Building Technologies Office: Recovery Act-Funded Ground Source Heat Pump Demonstration Projects on Digg Find More places to share Building Technologies Office: Recovery Act-Funded Ground Source Heat Pump Demonstration Projects on AddThis.com...

146

Protecting the Investment in Heat Recovery with Boiler Economizers  

E-Print Network (OSTI)

Many people consider energy to be a crisis in remission -- even with continuing high fuel costs. Some voice concern over the long term security of an investment in flue gas heat recovery equipment. The concern generally involves the ability of an economizer or air heater to continue to perform efficiently without corrosion. The recognized economic advantages of an economizer result from its ability to convert heat losses into sources of energy. One of the most productive means of obtaining reduced energy costs lies in the improvements of the efficiency of steam generating boilers. Industrial and institutional boilers operating at pressures of 75 psig or greater are excellent applications. The maximum gain that can be safely achieved is governed by a number of technical and physical limitations. Among these are considerations of the economics, temperatures of the flue gas and water, and the potential for corrosion. This paper will discuss the economic and practical considerations of an economizer installation.

Roethe, L. A.

1985-05-01T23:59:59.000Z

147

Effect of Heat Exchanger Material and Fouling on Thermoelectric Exhaust Heat Recovery  

Science Conference Proceedings (OSTI)

This study is conducted in an effort to better understand and improve the performance of thermoelectric heat recovery systems for automotive use. For this purpose an experimental investigation of thermoelectrics in contact with clean and fouled heat exchangers of different materials is performed. The thermoelectric devices are tested on a bench-scale thermoelectric heat recovery apparatus that simulates automotive exhaust. The thermoelectric apparatus consists of a series of thermoelectric generators contacting a hot-side and a cold-side heat exchanger. The thermoelectric devices are tested with two different hot-side heat exchanger materials, stainless steel and aluminum, and at a range of simulated exhaust gas flowrates (40 to 150 slpm), exhaust gas temperatures (240 C and 280 C), and coolant-side temperatures (40 C and 80 C). It is observed that for higher exhaust gas flowrates, thermoelectric power output increases while overall system efficiency decreases. Degradation of the effectiveness of the EGR-type heat exchangers over a period of driving is also simulated by exposing the heat exchangers to diesel engine exhaust under thermophoretic conditions to form a deposit layer. For the fouled EGR-type heat exchangers, power output and system efficiency is observed to be significantly lower for all conditions tested. The study found, however, that heat exchanger material is the dominant factor in the ability of the system to convert heat to electricity with thermoelectric generators. This finding is thought to be unique to the heat exchangers used for this study, and not a universal trend for all system configurations.

Love, Norman [University of Texas, El Paso; Szybist, James P [ORNL; Sluder, Scott [ORNL

2011-01-01T23:59:59.000Z

148

Analysis of IECC2003 Chiller Heat Recovery for Service Water Heating Requirement for New York State  

Science Conference Proceedings (OSTI)

The state of New York asked the U.S. Department of Energy to evaluate the cost-effectiveness of the requirement for Heat Recovery for Service Water Heating that exists in the 2003 International Energy Conservation Code to determine whether this requirement should be adopted into the New York State Energy Code. A typical hotel application that would trigger this requirement was examined using whole building simulation software to generate baseline annual chiller and service hot water loads, and a spreadsheet was used to examine the energy savings potential for heat recovery using hourly load files from the simulation. An example application meeting the code requirement was developed, and the energy savings, energy cost savings, and first costs for the heat recovery installation were developed. The calculated payback for this application was 6.3 years using 2002 New York state average energy costs. This payback met the minimum requirements for cost effectiveness established for the state of New York for updating the commercial energy conservation code.

Winiarski, David W.

2004-08-15T23:59:59.000Z

149

Analysis and modelling of membrane heat exchanger in HVAC energy recovery systems.  

E-Print Network (OSTI)

??The performance of membrane heat exchangers for HVAC total energy recovery systems was evaluated through experimentation and detailed system modelling. The operating principle of the… (more)

Nasif, Mohammad Shakir

2008-01-01T23:59:59.000Z

150

Property:Heat Recovery Rating | Open Energy Information  

Open Energy Info (EERE)

Rating Rating Jump to: navigation, search This is a property of type Number. Pages using the property "Heat Recovery Rating" Showing 22 pages using this property. D Distributed Generation Study/10 West 66th Street Corp + 300,000 + Distributed Generation Study/615 kW Waukesha Packaged System + 2,500,000 + Distributed Generation Study/Aisin Seiki G60 at Hooligans Bar and Grille + 46,105 + Distributed Generation Study/Arrow Linen + 3,000,000 + Distributed Generation Study/Dakota Station (Minnegasco) + 290,000 + Distributed Generation Study/Elgin Community College + 11,200,000 + Distributed Generation Study/Emerling Farm + 2,000,000 + Distributed Generation Study/Floyd Bennett + 230,000 + Distributed Generation Study/Harbec Plastics + 3,750,000 + Distributed Generation Study/Hudson Valley Community College + 32,500,000 +

151

Waste Heat Recovery in Cement Plants By Fluidized Beds  

E-Print Network (OSTI)

Not too many years ago energy costs and efficiencies were virtually ignored by corporate decision makers. The prevailing attitude was 'my business is manufacturing and my capital is best spent improving and expanding my manufacturing capacity.' With energy now contributing a significant fraction of the overall product cost in many industries, there is general recognition that control of fuel and electric costs is just as important to remaining competitive as is improving manufacturing methods. This is particularly true in the cement industry. Cement manufacture consists of mining and grinding rocks, melting them to form clinkers, then grinding those clinkers to a powder. Through recovery of waste heat and inclusion of technology such as flash calciners, the industry has reduced the fuel requirement per ton of cement from about 7 million Btu per ton in old plants to less than 3 million Btu per ton in the most modern plants.

Fraley, L. D.; Ksiao, H. K.; Thunem, C. B.

1984-01-01T23:59:59.000Z

152

Industrial Waste Heat Recovery Opportunities: An Update on Industrial High Temperature Heat Pump Technologies  

Science Conference Proceedings (OSTI)

It is estimated that as much as 20% to 50% of energy consumed is lost via waste heat contained in streams of exhaust gases and hot liquids, as well as through conduction, convection or radiation emanating from the surface of hot equipment. It is also estimated that in some cases, such as industrial furnaces, efficiency improvements resulting from waste heat recovery can improve efficiency by 10% to as much as 50%. This technical update is a continuation of research conducted by the Electric Power ...

2013-12-04T23:59:59.000Z

153

Enhancement of automotive exhaust heat recovery by thermoelectric devices  

SciTech Connect

In an effort to improve automobile fuel economy, an experimental study is undertaken to explore practical aspects of implementing thermoelectric devices for exhaust gas energy recovery. A highly instrumented apparatus consisting of a hot (exhaust gas) and a cold (coolant liquid) side rectangular ducts enclosing the thermoelectric elements has been built. Measurements of thermoelectric voltage output and flow and surface temperatures were acquired and analyzed to investigate the power generation and heat transfer properties of the apparatus. Effects of inserting aluminum wool packing material inside the hot side duct on augmentation of heat transfer from the gas stream to duct walls were studied. Data were collected for both the unpacked and packed cases to allow for detection of packing influence on flow and surface temperatures. Effects of gas and coolant inlet temperatures as well as gas flow rate on the thermoelectric power output were examined. The results indicate that thermoelectric power production is increased at higher gas inlet temperature or flow rate. However, thermoelectric power generation decreases with a higher coolant temperature as a consequence of the reduced hot-cold side temperature differential. For the hot-side duct, a large temperature gradient exists between the gas and solid surface temperature due to poor heat transfer through the gaseous medium. Adding the packing material inside the exhaust duct enhanced heat transfer and hence raised hot-side duct surface temperatures and thermoelectric power compared to the unpacked duct, particularly where the gas-to-surface temperature differential is highest. Therefore it is recommended that packing of exhaust duct becomes common practice in thermoelectric waste energy harvesting applications.

Ibrahim, Essam [Alabama A& M University, Normal; Szybist, James P [ORNL; Parks, II, James E [ORNL

2010-01-01T23:59:59.000Z

154

A Cross-Flow Ceramic Heat Recuperator for Industrial Heat Recovery  

E-Print Network (OSTI)

With increasing fuel costs, the efficient use of fuel is very important to the U.S. process heat industries. Increase in fuel usage efficiency can be obtained by transferring the waste exhaust heat to the cold combustion air. The metallic recuperators currently available suffer from problems of creep, corrosion and oxidation, particularly at high temperatures. The Department of Energy and GTE Products corporation have pursued a jointly funded venture, Contract No. EX-76-C-Q1-2162, to establish performance criteria and demonstrate a cross-flow ceramic heat recuperator for high temperature industrial heat recovery applications. The immediate goals of the ceramic recuperator project were to demonstrate a heat exchanger capable of handling high temperatures (1600-2400oF), that is compact with a high surface area and with costs comparable to the lower temperature metal heat exchangers. This paper describes the basic GTE Products Corporation design and details the design basis, the predicted recuperator performance, the ceramic and housing materials, the recuperator design procedure and the fabrication and assembly. The data provided includes NTU-Effectiveness and low friction and heat transfer ("f" and "J") plots.

Gonzalez, J. M.; Cleveland, J. J.; Kohnken, K. H.; Rebello, W. J.

1980-01-01T23:59:59.000Z

155

Heat Integration and Heat Recovery at a Large Chemical Manufacturing Plant  

E-Print Network (OSTI)

The Honeywell chemical plant located in Hopewell, Virginia includes processing units that purify raw phenol, react the phenol with hydrogen to form crude cyclohexanone, and purify the crude cyclohexanone. In order to reduce energy usage, two opportunities for heat recovery and heat integration were identified. A feasibility study and economic analysis were performed on the two opportunities, and both projects were implemented. The first project utilized the heat contained in a distillation process overheads stream to preheat the raw material entering the distillation process. This was accomplished via a heat exchanger, and reduced the utility steam requirement by 10,000 pph. The second project utilized the heat generated by the hydrogenation reaction (in the form of waste heat steam) to preheat the feed material in an adjacent process. This was accomplished via a heat exchanger, and reduced the utility steam requirement by 8,000 pph. These two energy projects required $1.1 million of capital and saved $1.0 million in utility steam annually.

Togna, K .A.

2012-01-01T23:59:59.000Z

156

Model based methodology development for energy recovery in flash heat exchange systems  

E-Print Network (OSTI)

Model based methodology development for energy recovery in flash heat exchange systems Problem with a condensing heat exchanger can be used when heat exchange is required between two streams and where at leastH, consistency etc.). To increase the efficiency of heat exchange, a cascade of these units in series can be used

McCarthy, John E.

157

Energy Savings By Recovery of Condensate From Steam Heating System  

E-Print Network (OSTI)

The recovery and utilization of condensate has a remarkable energy saving effect if the following are properly done: 1) Determination of a correct and reasonable recovery plan; 2) Selection of bleed valve with good performance; 3) Solving the problem of air bleeding, and 4) Scientific management of condensate system and bleed valve. If the above mentioned points are well dealt with, the recovery and utilization of condensate will be very beneficial.

Cheng, W. S.; Zhi, C. S.

1985-05-01T23:59:59.000Z

158

Energy saving opportunities through heat recovery from cement processing kilns: a case study  

Science Conference Proceedings (OSTI)

This paper proposes a system for the utilization of dissipated heat from the surfaces of cement processing kilns at the Jordan Cement Factories in heating heavy fuel oil used in the burning process of these kilns. It is proposed that this can be achieved ... Keywords: Jordan, cement, energy efficiency, heat recovery, kilns

I. Al-Hinti; A. Al-Ghandoor; A. Al-Naji; M. Abu-Khashabeh; M. Joudeh; M. Al-Hattab

2008-02-01T23:59:59.000Z

159

Waste Heat Recovery from Industrial Smelting Exhaust Gas  

Science Conference Proceedings (OSTI)

For a cost efficient capture of more valuable heat (higher exergy), heat exchangers should operate on the exhaust gases upstream of the gas treatment plants.

160

Advanced Organic Vapor Cycles for Improving Thermal Conversion Efficiency in Renewable Energy Systems  

E-Print Network (OSTI)

of heat recovery steam generators operating parameters forand Heat Recovery Steam Generators: Design, Applications,to the Heat Recovery Steam Generator (HRSG) is high, which

Ho, Tony

2012-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "hrsg heat recovery" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Design and development of eco-friendly alcohol engine fitted with waste heat recovery system  

Science Conference Proceedings (OSTI)

The present paper discusses the design and development of an eco-friendly alcohol engine fitted with the waste heat recovery system as a remedial alternative to the existing commonly used internal combustion engine. With the present trends in Internal ...

G. Vijayan Iyer; Nikos E. Mastorakis

2006-06-01T23:59:59.000Z

162

natural gas+ condensing flue gas heat recovery+ water creation+ CO2  

Open Energy Info (EERE)

natural gas+ condensing flue gas heat recovery+ water creation+ CO2 natural gas+ condensing flue gas heat recovery+ water creation+ CO2 reduction+ cool exhaust gases+ Energy efficiency+ commercial building energy efficiency+ industrial energy efficiency+ power plant energy efficiency+ Home Increase Natural Gas Energy Efficiency Description: Increased natural gas energy efficiency = Reduced utility bills = Profit In 2011 the EIA reports that commercial buildings, industry and the power plants consumed approx. 17.5 Trillion cu.ft. of natural gas. How much of that energy was wasted, blown up chimneys across the country as HOT exhaust into the atmosphere? 40% ~ 60% ? At what temperature? Links: The technology of Condensing Flue Gas Heat Recovery natural gas+ condensing flue gas heat recovery+ water creation+ CO2 reduction+ cool exhaust gases+ Energy efficiency+ commercial building

163

Mild Hybrid System in Combination with Waste Heat Recovery for Commercial Vehicles.  

E-Print Network (OSTI)

?? Performance of two different waste heat recovery systems (one based on Rankine cycle and the other one using thermoelectricity) combined with non-hybrid, mild-hybrid and… (more)

Namakian, Mohsen

2013-01-01T23:59:59.000Z

164

Thermal Energy Storage/Heat Recovery and Energy Conservation in Food Processing  

E-Print Network (OSTI)

Modern food processing operations often require that the temperature of the processed foodstuff be raised or lowered. These operations result in energy consumption by refrigeration or heating systems, and a portion of this energy can be recovered from waste heat streams for reuse in the processing operations. This paper addresses the recovery of waste heat and the storage of thermal energy as a means of energy conservation in food processing. An energy conservation project in a poultry processing plant sponsored by the U.S. Department of Energy and conducted by Georgia Tech is used as an illustrative example of potential applications of heat recovery and thermal energy storage.

Combes, R. S.; Boykin, W. B.

1980-01-01T23:59:59.000Z

165

Recovering heat when generating power  

Science Conference Proceedings (OSTI)

Intelligent use of heat-recovery stream generators (HRSGs) is vital for the efficient operation of cogeneration plants, which furnish both thermal energy (usually in the form of steam) and electric energy. HRSGs are similarly important in combined-cycle power plants, in which the thermal energy rejected from the primary electric-power-generation step is harnessed (as discussed below) to produce additional electrical energy. In these facilities, the HRSG is typically heated by gas-turbine exhaust. Natural gas is the fuel most widely used for gas turbines in the U.S., whereas fuel oil is the main fuel in other countries. Depending on the amount of steam to be produced, HRSGs for gas-turbine-exhaust applications may be unfired, supplementary-fired or furnace fired. The paper describes these three options; the pressure drop encountered in all three systems; the Cheng cycle; catalytic reduction of nitrogen oxides and CO; and performance testing.

Ganapathy, V.

1993-02-01T23:59:59.000Z

166

Recovery Act-Funded Water Heating Projects | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

of Performance (an efficiency measure) of up to 8. These next generation R-744 heat pump water heaters will be targeted for commercial use where cooling load is...

167

A novel heat recovery technology from an Aluminum reduction cell ...  

Science Conference Proceedings (OSTI)

The experimental setup consists of an electrical furnace which provides the simulated hot side walls, the control and measurement instruments, the heat ...

168

Heat Recovery from the Exhaust Gas of Aluminum Reduction Cells  

Science Conference Proceedings (OSTI)

Increased Energy Efficiency and Reduced HF Emissions with New Heat Exchanger · Industrial Test of Low-voltage Energy-saving Aluminum Reduction ...

169

Heat Recovery from Aluminium Reduction Cells - Programmaster.org  

Science Conference Proceedings (OSTI)

The three main heat sources (cathode sides, anode yokes, and gas) were combined in different ways, using different types of power cycles. The potential for ...

170

Waste Heat Recovery Trial from Aluminum Reduction Cell Exhaust ...  

Science Conference Proceedings (OSTI)

By using heat exchangers with in-line and staggered tube arrangements placed before fume treatment plant (FTP) we will be able to recover enough amount of ...

171

Optimization of Heat Recovery from the Precipitation Circuit  

Science Conference Proceedings (OSTI)

For this reason, plate heat exchangers are used both at inlet to Precipitation and in between precipitation stages at Vedanta Aluminium's Lanjigarh alumina ...

172

Renewable energy of waste heat recovery system for automobiles  

Science Conference Proceedings (OSTI)

A system to recover waste heat comprised of eight thermoelectric generators (TEGs) to convert heat from the exhaust pipe of an automobile to electrical energy has been constructed. Simulations and experiments for the thermoelectric module in this system are undertaken to assess the feasibility of these applications. In order to estimate the temperature difference between thermoelectric elements

Cheng-Ting Hsu; Da-Jeng Yao; Ke-Jyun Ye; Ben Yu

2010-01-01T23:59:59.000Z

173

Recovery Act-Funded Geothermal Heat Pump projects | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Geothermal Heat Pump Geothermal Heat Pump projects Recovery Act-Funded Geothermal Heat Pump projects The U.S. Department of Energy (DOE) was allocated funding from the American Recovery and Reinvestment Act to conduct research into ground source heat pump technologies and applications. Projects funded by the Recovery Act include: Historic Train Depot with a Hybrid System Funding amount: $1.7 million 1001 South 15th Street Associates LLC - New School and Performing Arts Theater The facility is a 23,000 square foot historic train depot requiring a GHP with 206 tons of cooling capacity. The hybrid GHP system incorporates a dry cooler to improve efficiency and life cycle effectiveness of the system by seasonally rebalancing the ground temperature. Grants Award Summary Massive Project with Massive Job Creation and Carbon Savings

174

Feasibility of Thermoelectrics for Waste Heat Recovery in Conventional Vehicles  

DOE Green Energy (OSTI)

Thermoelectric (TE) generators convert heat directly into electricity when a temperature gradient is applied across junctions of two dissimilar metals. The devices could increase the fuel economy of conventional vehicles by recapturing part of the waste heat from engine exhaust and generating electricity to power accessory loads. A simple vehicle and engine waste heat model showed that a Class 8 truck presents the least challenging requirements for TE system efficiency, mass, and cost; these trucks have a fairly high amount of exhaust waste heat, have low mass sensitivity, and travel many miles per year. These factors help maximize fuel savings and economic benefits. A driving/duty cycle analysis shows strong sensitivity of waste heat, and thus TE system electrical output, to vehicle speed and driving cycle. With a typical alternator, a TE system could allow electrification of 8%-15% of a Class 8 truck's accessories for 2%-3% fuel savings. More research should reduce system cost and improve economics.

Smith, K.; Thornton, M.

2009-04-01T23:59:59.000Z

175

HRSG Repair Welding Technologies to Address FAC in Tube Bends  

Science Conference Proceedings (OSTI)

Tube failures that occur in heat recovery steam generators (HRSGs) are often caused by thermal stress or thermal shock associated with cyclic plant operation or by flow-accelerated corrosion. Many premature failures occur along the length of finned tubes or at attachment locations where tubes are joined to the upper or lower header. Because of current tube repair practices and limited access for welding, reoccurring failures are common.

2008-03-20T23:59:59.000Z

176

Heat recovery in laundry yields 18-month payback  

SciTech Connect

A heat exchanger used to preheat hot water in a commercial laundry paid for itself in 19 months, despite a 10% increase in local natural gas rates. The Aurora, Illinois hospital commercial laundry chose a water-to-water shell and tube heat reclaimer system. A programmed control panel opens and closes valves at the proper temperature. Dirty water from the laundry cycle is screened to remove particles and returned to the heat exchanger to preheat incoming city water. Dirty water from the exchanger is discharged into the city sewer.

Hines, V.

1985-07-29T23:59:59.000Z

177

Install Waste Heat Recovery Systems for Fuel-Fired Furnaces (English/Chinese) (Fact Sheet)  

SciTech Connect

Chinese translation of ITP fact sheet about installing Waste Heat Recovery Systems for Fuel-Fired Furnaces. For most fuel-fired heating equipment, a large amount of the heat supplied is wasted as exhaust or flue gases. In furnaces, air and fuel are mixed and burned to generate heat, some of which is transferred to the heating device and its load. When the heat transfer reaches its practical limit, the spent combustion gases are removed from the furnace via a flue or stack. At this point, these gases still hold considerable thermal energy. In many systems, this is the greatest single heat loss. The energy efficiency can often be increased by using waste heat gas recovery systems to capture and use some of the energy in the flue gas. For natural gas-based systems, the amount of heat contained in the flue gases as a percentage of the heat input in a heating system can be estimated by using Figure 1. Exhaust gas loss or waste heat depends on flue gas temperature and its mass flow, or in practical terms, excess air resulting from combustion air supply and air leakage into the furnace. The excess air can be estimated by measuring oxygen percentage in the flue gases.

Not Available

2011-10-01T23:59:59.000Z

178

Thermally Activated Desiccant Technology for Heat Recovery and Comfort  

DOE Green Energy (OSTI)

Desiccant cooling is an important part of the diverse portfolio of Thermally Activated Technologies (TAT) designed for conversion of heat for the purpose of indoor air quality control. Thermally activated desiccant cooling incorporates a desiccant material that undergoes a cyclic process involving direct dehumidification of moist air and thermal regeneration. Desiccants fall into two categories: liquid and solid desiccants. Regardless of the type, solid or liquid, the governing principles of desiccant dehumidification systems are the same. In the dehumidification process, the vapor pressure of the moist air is higher than that of the desiccant, leading to transfer of moisture from the air to the desiccant material. By heating the desiccant, the vapor pressure differential is reversed in the regeneration process that drives the moisture from the desiccant. Figure 1 illustrates a rotary solid-desiccant dehumidifier. A burner or a thermally compatible source of waste heat can provide the required heat for regeneration.

Jalalzadeh, A. A.

2005-11-01T23:59:59.000Z

179

Development and Application of Advanced Models for Steam Hydrogasification: Process Design and Economic Evaluation  

E-Print Network (OSTI)

in a Heat Recovery Steam Generator (HRSG) to make additionalAuxiliary Power Block Steam turbine generator using steam

Lu, Xiaoming

2012-01-01T23:59:59.000Z

180

Thermodynamic Analysis of Combined Cycle District Heating System  

E-Print Network (OSTI)

This paper presents a thermodynamic analysis of the University of Massachusetts' Combined Heat and Power (CHP) District Heating System. Energy and exergy analyses are performed based on the first and second laws of thermodynamics for power generation systems that include a 10 MW Solar combustion gas turbine, a 4-MW steam turbine, a 100,000 pph heat recovery steam generator (HRSG), three 125,000 pph package boilers, and auxiliary equipment. In the analysis, actual system data is used to assess the district heating system performance, energy and exergy efficiencies, exergetic improvement potential and exergy losses. Energy and exergy calculations are conducted for the whole year on an hourly basis. System efficiencies are calculated for a wide range of component operating loads. The results show how thermodynamic analysis can be used to identify the magnitudes and location of energy losses in order to improve the existing system, processes or components.

Suresh, S.; Gopalakrishnan, H.; Kosanovic, D.

2011-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "hrsg heat recovery" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Advanced Thermoelectric Materials for Efficient Waste Heat Recovery in Process Industries  

DOE Green Energy (OSTI)

The overall objective of the project was to integrate advanced thermoelectric materials into a power generation device that could convert waste heat from an industrial process to electricity with an efficiency approaching 20%. Advanced thermoelectric materials were developed with figure-of-merit ZT of 1.5 at 275 degrees C. These materials were not successfully integrated into a power generation device. However, waste heat recovery was demonstrated from an industrial process (the combustion exhaust gas stream of an oxyfuel-fired flat glass melting furnace) using a commercially available (5% efficiency) thermoelectric generator coupled to a heat pipe. It was concluded that significant improvements both in thermoelectric material figure-of-merit and in cost-effective methods for capturing heat would be required to make thermoelectric waste heat recovery viable for widespread industrial application.

Adam Polcyn; Moe Khaleel

2009-01-06T23:59:59.000Z

182

Feasibility of Thermoelectrics for Waste Heat Recovery in Conventional Vehicles  

SciTech Connect

Thermoelectric (TE) generators convert heat directly into electricity when a temperature gradient is applied across junctions of two dissimilar metals. The devices could increase the fuel economy of conventional vehicles by recapturing part of the waste heat from engine exhaust and generating electricity to power accessory loads. A simple vehicle and engine waste heat model showed that a Class 8 truck presents the least challenging requirements for TE system efficiency, mass, and cost; these trucks have a fairly high amount of exhaust waste heat, have low mass sensitivity, and travel many miles per year. These factors help maximize fuel savings and economic benefits. A driving/duty cycle analysis shows strong sensitivity of waste heat, and thus TE system electrical output, to vehicle speed and driving cycle. With a typical alternator, a TE system could allow electrification of 8%-15% of a Class 8 truck's accessories for 2%-3% fuel savings. More research should reduce system cost and improve economics.

Smith, K.; Thornton, M.

2009-04-01T23:59:59.000Z

183

Energy Recovery By Direct Contact Gas-Liquid Heat Exchange  

E-Print Network (OSTI)

Energy from hot gas discharge streams can be recovered by transfer directly to a coolant liquid in one of several available gas-liquid contacting devices. The design of the device is central to the theme of this paper, and experimental work has verified that the analogy between heat transfer and mass transfer can be used for design purposes. This enables the large amount of available mass transfer data for spray, packed and tray columns to be used for heat transfer calculations. Additional information is provided on flow arrangements for integrating direct contact exchangers into systems for recovering the energy transferred to the liquid.

Fair, J. R.; Bravo, J. L.

1988-09-01T23:59:59.000Z

184

Waste heat recovery in automobile engines : potential solutions and benefits  

E-Print Network (OSTI)

Less than 30% of the energy in a gallon of gasoline reaches the wheels of a typical car; most of the remaining energy is lost as heat. Since most of the energy consumed by an internal combustion engine is wasted, capturing ...

Ruiz, Joaquin G., 1981-

2005-01-01T23:59:59.000Z

185

Energy recovery from waste incineration: Assessing the importance of district heating networks  

SciTech Connect

Municipal solid waste incineration contributes with 20% of the heat supplied to the more than 400 district heating networks in Denmark. In evaluation of the environmental consequences of this heat production, the typical approach has been to assume that other (fossil) fuels could be saved on a 1:1 basis (e.g. 1 GJ of waste heat delivered substitutes for 1 GJ of coal-based heat). This paper investigates consequences of waste-based heat substitution in two specific Danish district heating networks and the energy-associated interactions between the plants connected to these networks. Despite almost equal electricity and heat efficiencies at the waste incinerators connected to the two district heating networks, the energy and CO{sub 2} accounts showed significantly different results: waste incineration in one network caused a CO{sub 2} saving of 48 kg CO{sub 2}/GJ energy input while in the other network a load of 43 kg CO{sub 2}/GJ. This was caused mainly by differences in operation mode and fuel types of the other heat producing plants attached to the networks. The paper clearly indicates that simple evaluations of waste-to-energy efficiencies at the incinerator are insufficient for assessing the consequences of heat substitution in district heating network systems. The paper also shows that using national averages for heat substitution will not provide a correct answer: local conditions need to be addressed thoroughly otherwise we may fail to assess correctly the heat recovery from waste incineration.

Fruergaard, T.; Christensen, T.H. [Department of Environmental Engineering, Technical University of Denmark, Kongens Lyngby (Denmark); Astrup, T., E-mail: tha@env.dtu.d [Department of Environmental Engineering, Technical University of Denmark, Kongens Lyngby (Denmark)

2010-07-15T23:59:59.000Z

186

Waste heat recovery system having thermal sleeve support for heat pipe  

SciTech Connect

A system for recovering waste heat from a stream of heated gas is disclosed. The system includes a convection heat transfer chamber, a boiler tank, and a plurality of heat pipes thermally interconnecting the convection heat transfer chamber with the boiler tank. Each of the heat pipes includes an evaporator section which is disposed in heat transfer relation with a stream of heated gas flowing through the convection heat transfer chamber, and a condenser section disposed in heat transfer relation with a volume of water contained within the boiler tank. The boiler tank is provided with a header plate having an array of heat pipe openings through which the heat pipes project. A heat pipe support sleeve is received in each heat pipe opening in sealed engagement with the header plate, with the heat pipes projecting through the support sleeves and thermally interconnecting the convection heat transfer chamber with the boiler tank. An intermediate portion of each heat pipe is received in sealed engagement with its associated support sleeve. In a preferred embodiment, heat transfer through the support sleeve is minimized in an arrangement in which each heat pipe opening is reduced by a stepped bore with the support sleeve connected in threaded, sealed engagement with the stepped bore. Futhermore, in this arrangement, the support sleeve has swaged end portions which project beyond the header plate and engage the heat pipe on opposite sides at points which are remote with respect to the support sleeve/header plate interface. One of the swages end portions is sealed against the heat pipe in a fluid-tight union within the boiler tank. The support sleeve is radially spaced with respect to the heat pipe, and is also radially spaced with respect to the heat pipe opening whereby heat transfer through the walls of the heat pipe to the support sleeve and to the header plate is minimized by concentric annular air gaps.

McCurley, J.

1984-01-24T23:59:59.000Z

187

Waste heat recovery system having thermal sleeve support for heat pipe  

SciTech Connect

A system for recovering waste heat from a stream of heated gas is disclosed. The system includes a convection heat transfer chamber, a boiler tank, and a plurality of heat pipes thermally interconnecting the convection heat transfer chamber with the boiler tank. Each of the heat pipes includes an evaporator section which is disposed in heat transfer relation with a stream of heated gas flowing through the convection heat transfer chamber, and a condenser section disposed in heat transfer relation with a volume of water contained within the boiler tank. The boiler tank is provided with a header plate having an array of heat pipe openings through which the heat pipes project. A heat pipe support sleeve is received in each heat pipe opening in sealed engagement with the header plate, with the heat pipes projecting through the support sleeves and thermally interconnecting the convection heat transfer chamber with the boiler tank. An intermediate portion of each heat pipe is received in sealed engagement with its associated support sleeve. In a preferred embodiment, heat transfer through the support sleeve is minimized in an arrangement in which each heat pipe opening is reduced by a stepped bore with the support sleeve connected in threaded, sealed engagement with the stepped bore. Furthermore, in this arrangement, the support sleeve has swaged end portions which project beyond the header plate and engage the heat pipe on opposite sides at points which are remote with respect to the support sleeve/header plate interface. One of the swaged end portions is sealed against the heat pipe in a fluid-tight union within the boiler tank. The support sleeve is radially spaced with respect to the heat pipe, and is also radially spaced with respect to the heat pipe opening whereby heat transfer through the walls of the heat pipe to the support sleeve and to the header plate is minimized by concentric annular air gaps.

McCurley, J.

1984-04-10T23:59:59.000Z

188

Waste heat recovery system having thermal sleeve support for heat pipe  

SciTech Connect

A system for recovering waste heat from a stream of heated gas is disclosed. The system includes a convection heat transfer chamber, a boiler tank, and a plurality of heat pipes thermally interconnecting the convection heat transfer chamber with the boiler tank. Each of the heat pipes includes an evaporator section which is disposed in heat transfer relation with a stream of heated gas flowing through the convection heat transfer chamber, and a condenser section disposed in heat transfer relation with a volume of water contained within the boiler tank. The boiler tank is provided with a header plate having an array of heat pipe openings through which the heat pipes project. A heat pipe support sleeve is received in each heat pipe opening in sealed engagement with the header plate, with the heat pipes projecting through the support sleeves and thermally interconnecting the convection heat transfer chamber with the boiler tank. An intermediate portion of each heat pipe is received in sealed engagement with its associated support sleeve. In a preferred embodiment, heat transfer through the support sleeve is minimized in an arrangement in which each heat pipe opening is reduced by a stepped bore with the support sleeve connected in threaded, sealed engagement with the stepped bore. Furthermore, in this arrangement, the support sleeve has swaged end portions which project beyond the header plate and engage the heat pipe on opposite sides at points which are remote with respect to the support sleeve/header plate interface. One of the swaged end portions is sealed against the heat pipe in a fluid-tight union within the boiler tank. The support sleeve is radially spaced with respect to the heat pipe and is also radially spaced with respect to the heat pipe opening whereby heat transfer through the walls of the heat pipe to the support sleeve and to the header plate is minimized by concentric annular air gaps.

McCurley, J.

1984-12-04T23:59:59.000Z

189

Waste heat recovery system having thermal sleeve support for heat pipe  

SciTech Connect

A system for recovering waste heat from a stream of heated gas is disclosed. The system includes a convection heat transfer chamber, a boiler tank, and a plurality of heat pipes thermally interconnecting the convection heat transfer chamber with the boiler tank. Each of the heat pipes includes an evaporator section which is disposed in heat transfer relation with a stream of heated gas flowing through the convection heat transfer chamber, and a condenser section disposed in heat transfer relation with a volume of water contained within the boiler tank. The boiler tank is provided with a header plate having an array of heat pipe openings through which the heat pipes project. A heat support sleeve is received in each heat pipe opening in sealed engagement with the header plate, with the heat pipes projecting through the support sleeves and thermally interconnecting the convection heat transfer chamber with the boiler tank. An intermediate portion of each heat pipe is received in sealed engagement with its associated support sleeve. In a preferred embodiment, heat transfer through the support sleeve is minimized in an arrangement in which each heat pipe opening is reduced by a stepped bore with the support sleeve connected in threaded, sealed engagement with the stepped bore. Furthermore, in this arrangement, the support sleeve has swaged end portions which project beyond the header plate and engage the heat pipe on opposite sides at points which are remote with respect to the support sleeve/header plate interface. One of the swaged end portions is sealed against the heat pipe in a fluid-tight union within the boiler tank. The support sleeve is radially spaced with respect to the heat pipe, and is also radially spaced with respect to the heat pipe opening whereby heat transfer through the walls of the heat pipe to the support sleeve and to the header plate is minimized by concentric annular air gaps.

McCurley, J.

1984-12-18T23:59:59.000Z

190

Heat Recovery in Distillation by Mechanical Vapor Recompression  

E-Print Network (OSTI)

A significant reduction in distillation tower energy requirements can be achieved by mechanical vapor recompression. Three design approaches for heating a distillation tower reboiler by mechanical vapor recompression are presented. The advantages of using a screw compressor are discussed in detail. An example of a xylene extraction tower is sited, illustrating the economic attractiveness in which a simple payback period of less than two years is achievable.

Becker, F. E.; Zakak, A. I.

1986-06-01T23:59:59.000Z

191

Waste Heat Powered Ammonia Absorption Refrigeration Unit for LPG Recovery  

SciTech Connect

An emerging DOE-sponsored technology has been deployed. The technology recovers light ends from a catalytic reformer plant using waste heat powered ammonia absorption refrigeration. It is deployed at the 17,000 bpd Bloomfield, New Mexico refinery of Western Refining Company. The technology recovers approximately 50,000 barrels per year of liquefied petroleum gas that was formerly being flared. The elimination of the flare also reduces CO2 emissions by 17,000 tons per year, plus tons per year reductions in NOx, CO, and VOCs. The waste heat is supplied directly to the absorption unit from the Unifiner effluent. The added cooling of that stream relieves a bottleneck formerly present due to restricted availability of cooling water. The 350oF Unifiner effluent is cooled to 260oF. The catalytic reformer vent gas is directly chilled to minus 25oF, and the FCC column overhead reflux is chilled by 25oF glycol. Notwithstanding a substantial cost overrun and schedule slippage, this project can now be considered a success: it is both profitable and highly beneficial to the environment. The capabilities of directly-integrated waste-heat powered ammonia absorption refrigeration and their benefits to the refining industry have been demonstrated.

Donald C, Energy Concepts Co.; Lauber, Eric, Western Refining Co.

2008-06-20T23:59:59.000Z

192

Counter flow cooling drier with integrated heat recovery  

DOE Patents (OSTI)

A drier apparatus for removing water or other liquids from various materials includes a mixer, drying chamber, separator and regenerator and a method for use of the apparatus. The material to be dried is mixed with a heated media to form a mixture which then passes through the chamber. While passing through the chamber, a comparatively cool fluid is passed counter current through the mixture so that the mixture becomes cooler and drier and the fluid becomes hotter and more saturated with moisture. The mixture is then separated into drier material and media. The media is transferred to the regenerator and heated therein by the hot fluid from the chamber and supplemental heat is supplied to bring the media to a preselected temperature for mixing with the incoming material to be dried. In a closed loop embodiment of the apparatus, the fluid is also recycled from the regenerator to the chamber and a chiller is utilized to reduce the temperature of the fluid to a preselected temperature and dew point temperature.

Shivvers, Steve D. (Prole, IA)

2009-08-18T23:59:59.000Z

193

Fouling reduction characteristics of a no-distributor-fluidized-bed heat exchanger for flue gas heat recovery  

Science Conference Proceedings (OSTI)

In conventional flue gas heat recovery systems, the fouling by fly ashes and the related problems such as corrosion and cleaning are known to be major drawbacks. To overcome these problems, a single-riser no-distributor-fluidized-bed heat exchanger is devised and studied. Fouling and cleaning tests are performed for a uniquely designed fluidized bed-type heat exchanger to demonstrate the effect of particles on the fouling reduction and heat transfer enhancement. The tested heat exchanger model (1 m high and 54 mm internal diameter) is a gas-to-water type and composed of a main vertical tube and four auxiliary tubes through which particles circulate and transfer heat. Through the present study, the fouling on the heat transfer surface could successfully be simulated by controlling air-to-fuel ratios rather than introducing particles through an external feeder, which produced soft deposit layers with 1 to 1.5 mm thickness on the inside pipe wall. Flue gas temperature at the inlet of heat exchanger was maintained at 450{sup o}C at the gas volume rate of 0.738 to 0.768 CMM (0.0123 to 0.0128 m{sup 3}/sec). From the analyses of the measured data, heat transfer performances of the heat exchanger before and after fouling and with and without particles were evaluated. Results showed that soft deposits were easily removed by introducing glass bead particles, and also heat transfer performance increased two times by the particle circulation. In addition, it was found that this type of heat exchanger had high potential to recover heat of waste gases from furnaces, boilers, and incinerators effectively and to reduce fouling related problems.

Jun, Y.D.; Lee, K.B.; Islam, S.Z.; Ko, S.B. [Kongju National University, Kong Ju (Republic of Korea). Dept. for Mechanical Engineering

2008-07-01T23:59:59.000Z

194

Generation Maintenance Application Center: Combustion Turbine Combined-Cycle Heat Recovery Steam Generator Maintenance Guide  

Science Conference Proceedings (OSTI)

This guide provides information to assist personnel involved with the maintenance of the heat recovery steam generator at a combustion gas turbine combined cycle facility, including good maintenance practices, preventive maintenance techniques and troubleshooting guidance. BackgroundCombustion turbine combined cycle (CTCC) facilities utilize various components that can be unique to this particular type of power plant. As such, owners and ...

2013-05-15T23:59:59.000Z

195

New and Existing Buildings Heating and Cooling Opportunities: Dedicated Heat Recovery Chiller  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Langfitt Langfitt U S Department of State Overseas Buildings Operations Mechanical Engineering Division *Engineers are working Harder AND Smarter *New Energy Economy *Heating Is Where The Opportunity Is  39% of total US energy goes into non-residential buildings.  Gas for heating is about 60% of energy used in a building  Gas for heating is at least 25% of total energy used in the US. Heat Generation System Heat Disposal System What's Wrong With This Picture? Keep the heat IN the system Don't run main plant equipment until necessary ! Less rejected heat Less gas consumption High Temp >160F with conventional boilers Hydronic heating... condensing style modular boilers. The entire heating system... designed for low temperature water, recommend maximum temperature of 135ºF.

196

Advanced Energy and Water Recovery Technology from Low Grade Waste Heat  

SciTech Connect

The project has developed a nanoporous membrane based water vapor separation technology that can be used for recovering energy and water from low-temperature industrial waste gas streams with high moisture contents. This kind of exhaust stream is widely present in many industrial processes including the forest products and paper industry, food industry, chemical industry, cement industry, metal industry, and petroleum industry. The technology can recover not only the sensible heat but also high-purity water along with its considerable latent heat. Waste heats from such streams are considered very difficult to recover by conventional technology because of poor heat transfer performance of heat-exchanger type equipment at low temperature and moisture-related corrosion issues. During the one-year Concept Definition stage of the project, the goal was to prove the concept and technology in the laboratory and identify any issues that need to be addressed in future development of this technology. In this project, computational modeling and simulation have been conducted to investigate the performance of a nanoporous material based technology, transport membrane condenser (TMC), for waste heat and water recovery from low grade industrial flue gases. A series of theoretical and computational analyses have provided insight and support in advanced TMC design and experiments. Experimental study revealed condensation and convection through the porous membrane bundle was greatly improved over an impermeable tube bundle, because of the membrane capillary condensation mechanism and the continuous evacuation of the condensate film or droplets through the membrane pores. Convection Nusselt number in flue gas side for the porous membrane tube bundle is 50% to 80% higher than those for the impermeable stainless steel tube bundle. The condensation rates for the porous membrane tube bundle also increase 60% to 80%. Parametric study for the porous membrane tube bundle heat transfer performance was also done, which shows this heat transfer enhancement approach works well in a wide parameters range for typical flue gas conditions. Better understanding of condensing heat transfer mechanism for porous membrane heat transfer surfaces, shows higher condensation and heat transfer rates than non-permeable tubes, due to existence of the porous membrane walls. Laboratory testing has documented increased TMC performance with increased exhaust gas moisture content levels, which has exponentially increased potential markets for the product. The TMC technology can uniquely enhance waste heat recovery in tandem with water vapor recovery for many other industrial processes such as drying, wet and dry scrubber exhaust gases, dewatering, and water chilling. A new metallic substrate membrane tube development and molded TMC part fabrication method, provides an economical way to expand this technology for scaled up applications with less than 3 year payback expectation. A detailed market study shows a broad application area for this advanced waste heat and water recovery technology. A commercialization partner has been lined up to expand this technology to this big market. This research work led to new findings on the TMC working mechanism to improve its performance, better scale up design approaches, and economical part fabrication methods. Field evaluation work needs to be done to verify the TMC real world performance, and get acceptance from the industry, and pave the way for our commercial partner to put it into a much larger waste heat and waste water recovery market. This project is addressing the priority areas specified for DOE Industrial Technologies Program's (ITP's): Energy Intensive Processes (EIP) Portfolio - Waste Heat Minimization and Recovery platform.

Dexin Wang

2011-12-19T23:59:59.000Z

197

Section 5.3.1 Heat-Recovery Water Heating: Greening Federal Facilities...  

NLE Websites -- All DOE Office Websites (Extended Search)

heat pumps, chillers, steam condensate lines, hot air associated with kitchen and laundry facilities, power-generation equipment (such as microturbines or fuel cells), and...

198

Pulverized Coal OxyCombustion Power Plants  

NLE Websites -- All DOE Office Websites (Extended Search)

HHV Higher heating value hp Horsepower HP High pressure HRSG Heat Recovery Steam Generator HSS Heat stable salts HVAC Heating, ventilating, and air conditioning HWT Hot water...

199

Draft report: application of organic Rankine cycle heat recovery systems to diesel powered marine vessels  

DOE Green Energy (OSTI)

The analysis and results of an investigation of the application of organic Rankine cycle heat recovery systems to diesel-powered marine vessels are described. The program under which this study was conducted was sponsored jointly by the US Energy Research and Development Administration, the US Navy, and the US Maritime Administration. The overall objective of this study was to investigate diesel bottoming energy recovery systems, currently under development by three US concerns, to determine the potential for application to marine diesel propulsion and auxiliary systems. The study primarily focused on identifying the most promising vessel applications (considering vessel type, size, population density, operational duty cycle, etc.) so the relative economic and fuel conservation merits of energy recovery systems could be determined and assessed. Vessels in the current fleet and the projected 1985 fleet rated at 1000 BHP class and above were investigated.

Not Available

1977-07-15T23:59:59.000Z

200

Evaluation of Waste Heat Recovery and Utilization from Residential Appliances and Fixtures  

Science Conference Proceedings (OSTI)

Executive Summary In every home irrespective of its size, location, age, or efficiency, heat in the form of drainwater or dryer exhaust is wasted. Although from a waste stream, this energy has the potential for being captured, possibly stored, and then reused for preheating hot water or air thereby saving operating costs to the homeowner. In applications such as a shower and possibly a dryer, waste heat is produced at the same time as energy is used, so that a heat exchanger to capture the waste energy and return it to the supply is all that is needed. In other applications such as capturing the energy in drainwater from a tub, dishwasher, or washing machine, the availability of waste heat might not coincide with an immediate use for energy, and consequently a heat exchanger system with heat storage capacity (i.e. a regenerator) would be necessary. This study describes a two-house experimental evaluation of a system designed to capture waste heat from the shower, dishwasher clothes washer and dryer, and to use this waste heat to offset some of the hot water energy needs of the house. Although each house was unoccupied, they were fitted with equipment that would completely simulate the heat loads and behavior of human occupants including operating the appliances and fixtures on a demand schedule identical to Building American protocol (Hendron, 2009). The heat recovery system combined (1) a gravity-film heat exchanger (GFX) installed in a vertical section of drainline, (2) a heat exchanger for capturing dryer exhaust heat, (3) a preheat tank for storing the captured heat, and (4) a small recirculation pump and controls, so that the system could be operated anytime that waste heat from the shower, dishwasher, clothes washer and dryer, and in any combination was produced. The study found capturing energy from the dishwasher and clothes washer to be a challenge since those two appliances dump waste water over a short time interval. Controls based on the status of the dump valve on these two appliances would have eliminated uncertainty in knowing when waste water was flowing and the recovery system operated. The study also suggested that capture of dryer exhaust heat to heat incoming air to the dryer should be examined as an alternative to using drying exhaust energy for water heating. The study found that over a 6-week test period, the system in each house was able to recover on average approximately 3000 W-h of waste heat daily from these appliance and showers with slightly less on simulated weekdays and slightly more on simulated weekends which were heavy wash/dry days. Most of these energy savings were due to the shower/GFX operation, and the least savings were for the dishwasher/GFX operation. Overall, the value of the 3000 W-h of displaced energy would have been $0.27/day based on an electricity price of $.09/kWh. Although small for today s convention house, these savings are significant for a home designed to approach maximum affordable efficiency where daily operating costs for the whole house are less than a dollar per day. In 2010 the actual measured cost of energy in one of the simulated occupancy houses which waste heat recovery testing was undertaken was $0.77/day.

Tomlinson, John J [ORNL; Christian, Jeff [Oak Ridge National Laboratory (ORNL); Gehl, Anthony C [ORNL

2012-09-01T23:59:59.000Z

Note: This page contains sample records for the topic "hrsg heat recovery" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Use of Thermal Energy Storage to Enhance the Recovery and Utilization of Industrial Waste Heat  

E-Print Network (OSTI)

The recovery and reuse of industrial waste heat may be limited if an energy source cannot be fully utilized in an otherwise available out of phase or unequal capacity end-use process. This paper summarizes the results of a technical and economic evaluation involving process data from 12 industrial plants to determine if thermal energy storage (TES) systems can be used with commercially available energy management equipment to enhance the recovery and utilization of industrial waste heat. Results showing estimated installed costs, net energy savings, economic benefits, and utility impact are presented at both single plant and industry levels for 14 of 24 applications having after tax ROR's in excess of 20 percent. Maximum energy and cost savings for 9 of these 14 systems are shown to be conditional on the use of TES.

McChesney, H. R.; Bass, R. W.; Landerman, A. M.; Obee, T. N.; Sgamboti, C. T.

1982-01-01T23:59:59.000Z

202

Procurement Specification for Horizontal Gas Path Heat Recovery Steam Generator: Avoiding Thermal-Mechanical Fatigue Damage  

Science Conference Proceedings (OSTI)

Many heat recovery steam generators (HRSGs), particularly those equipped with F-class gas turbines that are also subjected to periods of frequent cyclic operation, have experienced premature pressure part failures because of excessive thermal-mechanical fatigue (TMF) damage. The very competitive power generation marketplace has resulted in lowest installed cost often taking precedence over medium- and long-term durability and operating costs.

2009-12-23T23:59:59.000Z

203

Waste Heat Recovery from the Advanced Test Reactor Secondary Coolant Loop  

Science Conference Proceedings (OSTI)

This study investigated the feasibility of using a waste heat recovery system (WHRS) to recover heat from the Advanced Test Reactor (ATR) secondary coolant system (SCS). This heat would be used to preheat air for space heating of the reactor building, thus reducing energy consumption, carbon footprint, and energy costs. Currently, the waste heat from the reactor is rejected to the atmosphere via a four-cell, induced-draft cooling tower. Potential energy and cost savings are 929 kW and $285K/yr. The WHRS would extract a tertiary coolant stream from the SCS loop and pump it to a new plate and frame heat exchanger, from which the heat would be transferred to a glycol loop for preheating outdoor air supplied to the heating and ventilation system. The use of glycol was proposed to avoid the freezing issues that plagued and ultimately caused the failure of a WHRS installed at the ATR in the 1980s. This study assessed the potential installation of a new WHRS for technical, logistical, and economic feasibility.

Donna Post Guillen

2012-11-01T23:59:59.000Z

204

Heat recovery steam generator outlet temperature control system for a combined cycle power plant  

Science Conference Proceedings (OSTI)

This patent describes a command cycle electrical power plant including: a steam turbine and at least one set comprising a gas turbine, an afterburner and a heat recovery steam generator having an attemperator for supplying from an outlet thereof to the steam turbine superheated steam under steam turbine operating conditions requiring predetermined superheated steam temperature, flow and pressure; with the gas turbine and steam turbine each generating megawatts in accordance with a plant load demand; master control means being provided for controlling the steam turbine and the heat recovery steam generator so as to establish the steam operating conditions; the combination of: first control means responsive to the gas inlet temperature of the heat recovery steam generator and to the plant load demand for controlling the firing of the afterburner; second control means responsive to the superheated steam predetermined temperature and to superheated steam temperature from the outlet for controlling the attemperator between a closed and an open position; the first and second control means being operated concurrently to maintain the superheated steam outlet temperature while controlling the load of the gas turbine independently of the steam turbine operating conditions.

Martens, A.; Myers, G.A.; McCarty, W.L.; Wescott, K.R.

1986-04-01T23:59:59.000Z

205

Assessment and development of an advanced heat pump for recovery of volatile organic compounds  

SciTech Connect

This report documents Phase 1 of a project conducted by Mechanical Technology Incorporated (MTI) for the assessment and development of an advanced heat pump for recovery of VOC solvents from process gas streams. In Phase 1, MTI has evaluated solvent recovery applications within New York State (NYS), identified host sites willing to implement their application, and conducted a preliminary design of the equipment required. The design and applications were evaluated for technical and economic feasibility. The solvent recovery heat pump system concept resulting from the Phase 1 work is one of a mobile unit that would service multiple stationary adsorbers. A large percentage of solvent recovery applications within the state can be serviced by on-site carbon bed adsorbers that are desorbed at frequencies ranging from once per to once per month. In this way, many users can effectively share'' the substantial capital investment associated with the system's reverse Brayton hardware, providing it can be packaged as a mobile unit. In a typical operating scenario, a carbon adsorption module will be located permanently at the industrial site. The SLA will be ducted through the adsorber and the solvents removed, thus eliminating an air emission problem. Prior to VOC breakthrough, by schedule or by request, the mobile unit would arrive at the site to recover the concentrated solvent. An engine driven, natural gas fueled system, the mobile unit utilizes conditioned engine exhaust gases as the inert gas for desorption. Hot inert gas is directed through the carbon bed, heating it and volatilizing the adsorbed solvent. Using a revere Brayton-cycle refrigeration system to create low temperatures, the solvent vapors are condensed and collected from the inert gas stream. The solvent can then be recycled to the production process or sold for other uses and the adsorber returned to service.

Not Available

1992-06-01T23:59:59.000Z

206

Assessment and development of an advanced heat pump for recovery of volatile organic compounds. Final report  

SciTech Connect

This report documents Phase 1 of a project conducted by Mechanical Technology Incorporated (MTI) for the assessment and development of an advanced heat pump for recovery of VOC solvents from process gas streams. In Phase 1, MTI has evaluated solvent recovery applications within New York State (NYS), identified host sites willing to implement their application, and conducted a preliminary design of the equipment required. The design and applications were evaluated for technical and economic feasibility. The solvent recovery heat pump system concept resulting from the Phase 1 work is one of a mobile unit that would service multiple stationary adsorbers. A large percentage of solvent recovery applications within the state can be serviced by on-site carbon bed adsorbers that are desorbed at frequencies ranging from once per to once per month. In this way, many users can effectively ``share`` the substantial capital investment associated with the system`s reverse Brayton hardware, providing it can be packaged as a mobile unit. In a typical operating scenario, a carbon adsorption module will be located permanently at the industrial site. The SLA will be ducted through the adsorber and the solvents removed, thus eliminating an air emission problem. Prior to VOC breakthrough, by schedule or by request, the mobile unit would arrive at the site to recover the concentrated solvent. An engine driven, natural gas fueled system, the mobile unit utilizes conditioned engine exhaust gases as the inert gas for desorption. Hot inert gas is directed through the carbon bed, heating it and volatilizing the adsorbed solvent. Using a revere Brayton-cycle refrigeration system to create low temperatures, the solvent vapors are condensed and collected from the inert gas stream. The solvent can then be recycled to the production process or sold for other uses and the adsorber returned to service.

Not Available

1992-06-01T23:59:59.000Z

207

Proposed Design for a Coupled Ground-Source Heat Pump/Energy Recovery Ventilator System to Reduce Building Energy Demand.  

E-Print Network (OSTI)

??The work presented in this thesis focuses on reducing the energy demand of a residential building by using a coupled ground-source heat pump/energy recovery ventilation… (more)

McDaniel, Matthew Lee

2011-01-01T23:59:59.000Z

208

Solar Thermochemical Fuels Production: Solar Fuels via Partial Redox Cycles with Heat Recovery  

SciTech Connect

HEATS Project: The University of Minnesota is developing a solar thermochemical reactor that will efficiently produce fuel from sunlight, using solar energy to produce heat to break chemical bonds. The University of Minnesota is envisioning producing the fuel by using partial redox cycles and ceria-based reactive materials. The team will achieve unprecedented solar-to-fuel conversion efficiencies of more than 10% (where current state-of-the-art efficiency is 1%) by combined efforts and innovations in material development, and reactor design with effective heat recovery mechanisms and demonstration. This new technology will allow for the effective use of vast domestic solar resources to produce precursors to synthetic fuels that could replace gasoline.

None

2011-12-19T23:59:59.000Z

209

Model for determining modular heat recovery incinerator feasibility on air force installations. Master's thesis  

Science Conference Proceedings (OSTI)

This study constructed a model to determine the feasibility of building municipal solid waste (MSW) fired modular heat recovery incinerators (HRIs) on Air Force installations. The model consisted of three gates. Gate one identified current federal regulatory air emission requirements for various HRI pollutants. It also specified two air pollution control configurations with emission reduction efficiencies capable of achieving these requirements. Gate two presented a life-cycle cost (LCC) economic analysis methodology. Operational and cost data for existing modular HRIs located in the United States facilitated the development of regression equations that estimate capital and annual operating costs for a modular HRI. Actual cost and operational information from a central heating plant at Wright-Patterson AFB, along with cost data from the regression equations, provided the basis for an example LCC analysis involving modular HRIs Results of this hypothetical evaluation showed that the LCC for the modular HRI alternatives were both less than the LCC of replacing the existing boiler. Gate three presented a Likert-scale survey to evaluate the sociopolitical acceptability of the proposed HRI. The survey results indicate the level of effort to process the HRI proposal in accordance with the National Environmental Policy Act. Heat recovery, Incinerators, Waste management, Waste treatment.

Anderson, A.H.; Munnell, P.R.

1992-09-01T23:59:59.000Z

210

Thermal Energy Storage/Waste Heat Recovery Applications in the Cement Industry  

E-Print Network (OSTI)

The cement industry is the most energy-intensive industry in the United States in terms of energy cost as a percentage of the product according to a 1973 report by the Cost of Living Council. Martin Marietta Aerospace, Denver Division, and the Portland Cement Association have studied the potential benefits of using waste heat recovery methods and thermal energy storage systems in the cement manufacturing process. This work was performed under DOE Contract No. EC-77-C-01-50S4. The study has been completed and illustrates very attractive cost benefits realized from waste heat recovery/thermal storage systems. This paper will identify and quantify the sources of rejected energy in the cement manufacturing process, establish uses of this energy, exhibit various energy storage concepts, and present a methodology for selection of most promising energy storage systems. Two storage systems show the best promise - rock beds and draw salt storage. Thermal performance and detailed economic analyses have been performed on these systems and will be presented. Through use of thermal energy storage in conjunction with waste heat electric power generation units, an estimated 2.4 x 1013 BTU per year, or an equivalent of 4.0 x 10 barrels of oil per year, can be conserved. Attractive rates of return on investment of the proposed systems are an incentive for utilization and further development.

Beshore, D. G.; Jaeger, F. A.; Gartner, E. M.

1979-01-01T23:59:59.000Z

211

HRSG/SR Revised 07/01/08 Page 1 of 2 HAZARD ASSESSMENT SURVEY & ANALYSIS  

E-Print Network (OSTI)

HRSG/SR Revised 07/01/08 Page 1 of 2 HAZARD ASSESSMENT SURVEY & ANALYSIS PERSONAL PROTECTIVE is accomplished by surveying the workplace to determine where physical or health hazards are present or likely to noise levels. (>85 dBA 8-hour TWA) Ear muffs or plugs Nuisance dust/mist Welding fumes Asbestos

Eirinaki, Magdalini

212

Willamina Project Report : Indirect-Fired, Biomass-Fueled, Combined-Cycle, Gas Turbine Power Plant Using a Ceramic Heat Exchanger. Volume 1. Conceptual Plant Design and Analysis. Final report. [Contains Glossary  

SciTech Connect

A new technology for a wood-fueled electrical generation plant was evaluated. The proposed plant utilizes an indirectly fired gas turbine (IFGT) using a ceramic heat exchanger for high efficiency, due to its high temperature capability. The proposed plant utilizes a wood-fueled furnace with a ceramic heat exchanger to heat compressed air for a gas turbine. The configuration proposed is a combined cycle power plant that can produce 6 to 12 MW, depending upon the amount of wood used to supplementally fire a heat recovery steam generator (HRSG), which in turn powers a steam turbine. Drawings, specifications, and cost estimates based on a combined cycle analysis and wood-fired HRSG were developed. The total plant capital cost was estimated to be $13.1 million ($1640/kW). The heat rate for a 8-MW plant was calculated to be 10,965 Btu/kW when using wood residues with a 42% moisture content. Levelized electric energy costs were estimated to be 6.9 cents/kWh.

F.W. Braun Engineers.

1984-05-01T23:59:59.000Z

213

Recovery of Water from Boiler Flue Gas Using Condensing Heat Exchangers  

Science Conference Proceedings (OSTI)

Most of the water used in a thermoelectric power plant is used for cooling, and DOE has been focusing on possible techniques to reduce the amount of fresh water needed for cooling. DOE has also been placing emphasis on recovery of usable water from sources not generally considered, such as mine water, water produced from oil and gas extraction, and water contained in boiler flue gas. This report deals with development of condensing heat exchanger technology for recovering moisture from flue gas from coal-fired power plants. The report describes: • An expanded data base on water and acid condensation characteristics of condensing heat exchangers in coal-fired units. This data base was generated by performing slip stream tests at a power plant with high sulfur bituminous coal and a wet FGD scrubber and at a power plant firing highmoisture, low rank coals. • Data on typical concentrations of HCl, HNO{sub 3} and H{sub 2}SO{sub 4} in low temperature condensed flue gas moisture, and mercury capture efficiencies as functions of process conditions in power plant field tests. • Theoretical predictions for sulfuric acid concentrations on tube surfaces at temperatures above the water vapor dewpoint temperature and below the sulfuric acid dew point temperature. • Data on corrosion rates of candidate heat exchanger tube materials for the different regions of the heat exchanger system as functions of acid concentration and temperature. • Data on effectiveness of acid traps in reducing sulfuric acid concentrations in a heat exchanger tube bundle. • Condensed flue gas water treatment needs and costs. • Condensing heat exchanger designs and installed capital costs for full-scale applications, both for installation immediately downstream of an ESP or baghouse and for installation downstream of a wet SO{sub 2} scrubber. • Results of cost-benefit studies of condensing heat exchangers.

Levy, Edward; Bilirgen, Harun; DuPont, John

2011-03-31T23:59:59.000Z

214

Recovery of Water from Boiler Flue Gas Using Condensing Heat Exchangers  

Science Conference Proceedings (OSTI)

Most of the water used in a thermoelectric power plant is used for cooling, and DOE has been focusing on possible techniques to reduce the amount of fresh water needed for cooling. DOE has also been placing emphasis on recovery of usable water from sources not generally considered, such as mine water, water produced from oil and gas extraction, and water contained in boiler flue gas. This report deals with development of condensing heat exchanger technology for recovering moisture from flue gas from coal-fired power plants. The report describes: (1) An expanded data base on water and acid condensation characteristics of condensing heat exchangers in coal-fired units. This data base was generated by performing slip stream tests at a power plant with high sulfur bituminous coal and a wet FGD scrubber and at a power plant firing high-moisture, low rank coals. (2) Data on typical concentrations of HCl, HNO{sub 3} and H{sub 2}SO{sub 4} in low temperature condensed flue gas moisture, and mercury capture efficiencies as functions of process conditions in power plant field tests. (3) Theoretical predictions for sulfuric acid concentrations on tube surfaces at temperatures above the water vapor dewpoint temperature and below the sulfuric acid dew point temperature. (4) Data on corrosion rates of candidate heat exchanger tube materials for the different regions of the heat exchanger system as functions of acid concentration and temperature. (5) Data on effectiveness of acid traps in reducing sulfuric acid concentrations in a heat exchanger tube bundle. (6) Condensed flue gas water treatment needs and costs. (7) Condensing heat exchanger designs and installed capital costs for full-scale applications, both for installation immediately downstream of an ESP or baghouse and for installation downstream of a wet SO{sub 2} scrubber. (8) Results of cost-benefit studies of condensing heat exchangers.

Edward Levy; Harun Bilirgen; John DuPoint

2011-03-31T23:59:59.000Z

215

Pressure recovery in a cylindrical heat pipe at high radial Reynolds numbers and at high Mach numbers  

SciTech Connect

The pressure recovery in a cylindrical heat pipe has been investigated. The experiments cover average radial Reynolds numbers between 5 and 150 and average Mach numbers up to the velocity of sound. During preliminary experiments in a cylindrical, gravity-assisted heat pipe at high Mach numbers large condensate flow instabilities were observed. As a consequence the heat pipe power varied strongly. Based on these observations an improved heat pipe design was made that resulted in steady operating conditions throughout the entire parameter range. This heat pipe is described. The pressure recovery was measured and compared with results from a two-dimensional analytical model for describing compressible vapor flow in heat pipes. Good agreement with the experimental data was found.

Haug, F.; Busse, C.A.

1985-01-01T23:59:59.000Z

216

Evaluation of Industrial Energy Options for Cogeneration, Waste Heat Recovery and Alternative Fuel Utilization  

E-Print Network (OSTI)

This paper describes the energy options available to Missouri industrial firms in the areas of cogeneration, waste heat recovery, and coal and alternative fuel utilization. The project, being performed by Synergic Resources Corporation for the Missouri Division of Energy, identifies and evaluates technological options and describes the current status of various energy resource conservation technologies applicable industry and the economic, institutional and regulatory factors which could affect the implementation and use of these energy technologies. An industrial energy manual has been prepared, identifying technologies with significant potential for application in a specific company or plant. Six site-specific industrial case studies have been performed for industries considered suitable for cogeneration, waste heat recovery or alternative fuel use. These case studies, selected after a formal screening process, evaluate actual plant conditions and economics for Missouri industrial establishments. It is hoped that these case studies will show, by example, some of the elements that make energy resource conservation technologies economically a technically feasible in the real world.

Hencey, S.; Hinkle, B.; Limaye, D. R.

1980-01-01T23:59:59.000Z

217

Waste Heat Doesn't Have to be a Waste of Money- The American & Efird Heat Recovery Project: A First for the Textile Industry  

E-Print Network (OSTI)

In 1989 American & Efird, Inc., decided to upgrade their heat recovery system at its Dyeing & Finishing Plant in Mt. Holly, North Carolina. They chose an electric industrial process heat pump to enhance heat recovery and to lower operating costs. This application of the industrial process heat pump was the first of its kind in the American textile industry and was the result of a three year cooperative effort between American & Efird, Inc. and Duke Power Company. This innovative application of heat pump technology has allowed American & Efird to gain additional boiler capacity, lower waste water discharge temperatures and achieve significant energy savings. Duke Power will gain an additional 572,000 KWH in annual sales, of which approximately 70 percent will occur during off-peak hours, and American & Efird will enjoy lower overall energy costs.

Smith, S. W.

1991-06-01T23:59:59.000Z

218

Advanced heat pump for the recovery of volatile organic compounds. Phase 1, Conceptual design of an advanced Brayton cycle heat pump for the recovery of volatile organic compounds: Final report  

Science Conference Proceedings (OSTI)

Emissions of Volatile Organic Compounds (VOC) from stationary industrial and commercial sources represent a substantial portion of the total US VOC emissions. The ``Toxic-Release Inventory`` of The US Environmental Protection Agency estimates this to be at about 3 billion pounds per year (1987 estimates). The majority of these VOC emissions are from coating processes, cleaning processes, polymer production, fuel production and distribution, foam blowing,refrigerant production, and wood products production. The US Department of Energy`s (DOE) interest in the recovery of VOC stems from the energy embodied in the recovered solvents and the energy required to dispose of them in an environmentally acceptable manner. This Phase I report documents 3M`s work in close working relationship with its subcontractor Nuclear Consulting Services (Nucon) for the preliminary conceptual design of an advanced Brayton cycle heat pump for the recovery of VOC. Nucon designed Brayton cycle heat pump for the recovery of methyl ethyl ketone and toluene from coating operations at 3M Weatherford, OK, was used as a base line for the work under cooperative agreement between 3M and ODE. See appendix A and reference (4) by Kovach of Nucon. This cooperative agreement report evaluates and compares an advanced Brayton cycle heat pump for solvent recovery with other competing technologies for solvent recovery and reuse. This advanced Brayton cycle heat pump is simple (very few components), highly reliable (off the shelf components), energy efficient and economically priced.

Not Available

1992-03-01T23:59:59.000Z

219

Organic Rankine Cycle Systems for Waste Heat Recovery in Refineries and Chemical Process Plants  

E-Print Network (OSTI)

The design of a low temperature Rankine cycle system using R-113 working fluid for recovery and conversion of process waste heat is described for typical applications in oil refineries and chemical plants. The system is designed to produce electric power from waste heat available in a temperature range from 180oF to 400oF. The design of a new ORC turbo generator uniquely adapted to applications of this type is presented. The unit has been designed for power outputs from 3/4 to 2 1/2 MW and turbine inlet temperatures from 170 to 260oF. The machine design has eliminated the need for shaft seals, shaft couplings and the usual lube oil console normally required for turbine-generator units. Results of prototype tests of a 1 MW unit are presented. A product package and recommended division of responsibilities between purchaser, A&E company and supplier is presented for installations in refineries and process plants. The product package covers the electrical power range from 3/4 to 5 MW and waste heat streams from 20 to 130 million BTU/hr.

Meacher, J. S.

1981-01-01T23:59:59.000Z

220

Combustion testing and heat recovery study: Frank E. Van Lare Wastewater Treatment Plant, Monroe County. Final report  

DOE Green Energy (OSTI)

The objectives of the study were to record and analyze sludge management operations data and sludge incinerator combustion data; ascertain instrumentation and control needs; calculate heat balances for the incineration system; and determine the feasibility of different waste-heat recovery technologies for the Frank E. Van Lare (FEV) Wastewater Treatment Plant. As an integral part of this study, current and pending federal and state regulations were evaluated to establish their impact on furnace operation and subsequent heat recovery. Of significance is the effect of the recently promulgated Federal 40 CFR Part 503 regulations on the FEV facility. Part 503 regulations were signed into law in November 1992, and, with some exceptions, affected facilities must be in compliance by February 19, 1994. Those facilities requiring modifications or upgrades to their incineration or air pollution control equipment to meet Part 503 regulations must be in compliance by February 19, 1995.

NONE

1995-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "hrsg heat recovery" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Evaluating and Avoiding HRSG Pressure Part Damage Influenced by Stack Damper Operation  

Science Conference Proceedings (OSTI)

Electric Power Research Institute (EPRI) tube failure data indicate that thermal fatigue is currently the second most prevalent pressure part failure mechanism affecting heat recovery steam generators (HRSGs). It should be anticipated that as HRSGs accumulate more startups and the number of thermal cycles increases, thermal fatigue pressure part failures will occur more often.

2009-12-02T23:59:59.000Z

222

Applications of thermal energy storage to process heat and waste heat recovery in the primary aluminum industry. Final report, September 1977-September 1978  

DOE Green Energy (OSTI)

The results of a study entitled, Applications of Thermal Energy Storage to Process Heat and Waste Heat Recovery in the Primary Aluminum Industry are presented. In this preliminary study, a system has been identified by which the large amounts of low-grade waste energy in the primary pollution control system gas stream can be utilized for comfort heating in nearby communities. Energy is stored in the form of hot water, contained in conventional, insulated steel tanks, enabling a more efficient utilization of the constant energy source by the cyclical energy demand. Less expensive energy storage means (heated ponds, aquifers), when they become fully characterized, will allow even more cost-competitive systems. Extensive design tradeoff studies have been performed. These tradeoff studies indicate that a heating demand equivalent to 12,000 single-family residences can be supplied by the energy from the Intalco plant. Using a 30-year payback criterion (consistent with utility planning practice), the average cost of energy supplied over the system useful life is predicted at one-third the average cost of fossil fuel. The study clearly shows that the utilization of waste energy from aluminum plants is both technically and economically attractive. The program included a detailed survey of all aluminum plants within the United States, allowing the site specific analyses to be extrapolated to a national basis. Should waste heat recovery systems be implemented by 1985, a national yearly savings of 6.5 million barrels of oil can be realized.

Katter, L.B.; Hoskins, R.L.

1979-04-01T23:59:59.000Z

223

Furnace and Heat Recovery Area Design and Analysis for Conceptual Design of Oxygen-Based PC Boiler  

Science Conference Proceedings (OSTI)

The objective of the furnace and heat recovery area design and analysis task of the Conceptual Design of Oxygen-Based PC Boiler study is to optimize the location and design of the furnace, burners, over-fire gas ports, and internal radiant surfaces. The furnace and heat recovery area were designed and analyzed using the FW-FIRE and HEATEX computer programs. The furnace is designed with opposed wall-firing burners and over-fire air ports. Water is circulated in the furnace by natural circulation to the waterwalls and divisional wall panels. Compared to the air-fired furnace, the oxygen-fired furnace requires only 65% of the surface area and 45% of the volume. Two oxygen-fired designs were simulated: (1) without over-fire air and (2) with 20% over-fire air. The maximum wall heat flux in the oxygen-fired furnace is more than double that of the air-fired furnace due to the higher flame temperature and higher H{sub 2}O and CO{sub 2} concentrations. The coal burnout for the oxygen-fired case is 100% due to a 500 F higher furnace temperature and higher concentration of O{sub 2}. Because of the higher furnace wall temperature of the oxygen-fired case compared to the air-fired case, furnace water wall material was upgraded from carbon steel to T91. The total heat transfer surface required in the oxygen-fired heat recovery area (HRA) is 25% less than the air-fired HRA due to more heat being absorbed in the oxygen-fired furnace and the greater molecular weight of the oxygen-fired flue gas. The HRA tube materials and wall thickness are practically the same for the air-fired and oxygen-fired design since the flue gas and water/steam temperature profiles encountered by the heat transfer banks are very similar.

Andrew Seltzer

2005-01-01T23:59:59.000Z

224

Emission Control and Elimination Through The Use Of Condensation and Heat Recovery Technologies- A Case Study  

E-Print Network (OSTI)

Existing regulatory air requirements have created potential restrictions on current and future plant operations. Any process design that allows for the elimination of discharge points and the reduction of emissions at a major source can affect the strategic planning for the facility. This can provide critical flexibility, especially in fast-paced markets. Such a process design and implementation were undertaken at a ceramic capacitor manufacturing facility. This facility utilizes multiple small-scale solvent drying processes that emit volatile organic compounds (VOC's). These exhausts could be recirculated for the purposes of emission point elimination, heat recovery and solvent reuse. The aim was to create an environmental control process which would pay for itself within two to three years. An assessment of the alternatives was completed and standard HVAC-type condensation was selected. The unit operations for the proposed process consisted of a high efficiency air-to-air heat exchanger, cooling coil and a chiller. The air passing across the heat exchanger and coil would begin to dehumidify. In addition, solvents contained in the air stream would begin to condense to some equilibrium level and would be absorbed in the condensing water. Eventually, since there would be no addition of water in the process, the level of water in the condensate would fall off dramatically. A prototype unit capable of handling three ovens with a total air flow of 1200 ft3/min (cfm) was installed. The unit performed as expected with the exception that condensate concentrations remained low. Product testing was undertaken to ensure that returning air containing a low level of solvent would not adversely affect drying operations or product qualities. No adverse effects were found. Monitoring of the air stream verified solvent levels well below 5% of the lower explosive limit. Finally, a large-scale unit was constructed capable of handling up to 171 ovens at up to 68,000 cfm at a cost of $1.2M. At current levels of integration, cost avoidance (savings) performance is within 2% of predicted values. Projected payback is 18 months. Estimated volatile organic compound emission reduction is 100 tons per year.

Madewell, A. E.; Bullock, W. N.

1997-04-01T23:59:59.000Z

225

Simulation et aide au dimensionnement des chaudičres de récupération.  

E-Print Network (OSTI)

??Heat recovery steam generators (HRSG) play a very important role in combined cycle (CC) power plants, where steam is generated from a gas turbine exhaust… (more)

Dumont, Marie-Noelle

2007-01-01T23:59:59.000Z

226

Estimating performance of HRSGs is simplified  

Science Conference Proceedings (OSTI)

This article describes calculating heat recovery steam generators (HRSG) performance without the use of an elaborate computer program. In designing HRSG, used in gas-turbine-based cogeneration plants, the following information must be calculated: HRSG steam production in the fired and unfired mode, oxygen content of the exhaust, and fuel consumption. With the simplified procedure described, engineers can obtain the information quickly without consulting HRSG suppliers or using a computer program.

Ganapathy, V. (ABCO Industries, Abilene, TX (United States))

1994-08-01T23:59:59.000Z

227

Program Final Report - Develop Thermoelectric Technology for Automotive Waste Heat Recovery  

Science Conference Proceedings (OSTI)

We conducted a vehicle analysis to assess the feasibility of thermoelectric technology for waste heat recovery and conversion to useful electrical power and found that eliminating the 500 W of electrical power generated by the alternator corresponded to about a 7% increase in fuel economy (FE) for a small car and about 6% for a full size truck. Electric power targets of 300 W were established for city and highway driving cycles for this project. We obtained critical vehicle level information for these driving cycles that enabled a high-level design and performance analysis of radiator and exhaust gas thermoelectric subsystems for several potential vehicle platforms, and we identified the location and geometric envelopes of the radiator and exhaust gas thermoelectric subsystems. Based on this analysis, we selected the Chevrolet Suburban as the most suitable demonstration vehicle for this project. Our modeling and thermal analysis assessment of a radiator-based thermoelectric generator (TEG), however, revealed severe practical limitations. Specifically the small temperature difference of 100°C or less between the engine coolant and ambient air results in a low Carnot conversion efficiency, and thermal resistance associated with air convection would reduce this conversion efficiency even further. We therefore decided not to pursue a radiator-based waste heat recovery system and focused only on the exhaust gas. Our overall approach was to combine science and engineering: (1) existing and newly developed TE materials were carefully selected and characterized by the material researcher members of our team, and most of the material property results were validated by our research partners, and (2) system engineers worked closely with vehicle engineers to ensure that accurate vehicle-level information was used for developing subsystem models and designs, and the subsystem output was analyzed for potential fuel economy gains. We incorporated material, module, subsystem, and integration costs into the material selection criteria in order to balance various materials, module and subsystem design, and vehicle integration options. Our work on advanced TE materials development and on TEG system design, assembly, vehicle integration, and testing proceeded in parallel efforts. Results from our two preliminary prototype TEGs using only Bi-Te TE modules allowed us to solve various mechanical challenges and to finalize and fine tune aspects of the design and implementation. Our materials research effort led us to quickly abandon work on PbTe and focus on the skutterudite materials due to their superior mechanical performance and suitability at automotive exhaust gas operating temperatures. We synthesized a sufficiently large quantity of skutterudite material for module fabrication for our third and final prototype. Our TEG#3 is the first of its kind to contain state-of-the-art skutterudite-based TE modules to be installed and tested on a production vehicle. The design, which consisted of 24 skutterudite modules and 18 Bi-Te modules, attempted to optimize electrical power generation by using these two kinds of TE modules that have their peak performance temperatures matched to the actual temperature profile of the TEG during operation. The performance of TEG#3 was limited by the maximum temperature allowable for the Bi-Te TE modules located in the colder end of the TEG, resulting in the operating temperature for the skutterudite modules to be considerably below optimum. We measured the power output for (1) the complete TEG (25 Watts) and (2) an individual TE module series string (1/3 of the TEG) operated at a 60°C higher temperature (19 Watts). We estimate that under optimum operating temperature conditions, TEG#3 will generate about 235 Watts. With additional improvements in thermal and electrical interfaces, temperature homogeneity, and power conditioning, we estimate TEG#3 could deliver a power output of about 425 Watts.

Gregory Meisner

2011-08-31T23:59:59.000Z

228

Investigating potential light-duty efficiency improvements through simulation of turbo-compounding and waste-heat recovery systems  

Science Conference Proceedings (OSTI)

Modern diesel engines used in light-duty transportation applications have peak brake thermal efficiencies in the range of 40-42% for high-load operation with substantially lower efficiencies at realistic road-load conditions. Thermodynamic energy and exergy analysis reveals that the largest losses from these engines are due to combustion irreversibility and heat loss to the coolant, through the exhaust, and by direct convection and radiation to the environment. Substantial improvement in overall engine efficiency requires reducing or recovering these losses. Unfortunately, much of the heat transfer either occurs at relatively low temperatures resulting in large entropy generation (such as in the air-charge cooler), is transferred to low-exergy flow streams (such as the oil and engine coolant), or is radiated or convected directly to the environment. While there are significant opportunities for recovery from the exhaust and EGR cooler for heavy-duty applications, achieving similar benefits for light-duty applications is complicated by transient, low-load operation at typical driving conditions and competition with the turbocharger and aftertreatment system for the limited thermal resources. We have developed an organic Rankine cycle model using GT-Suite to investigate the potential for efficiency improvement through waste-heat recovery from the exhaust and EGR cooler of a light-duty diesel engine. The model is used to examine the effects of efficiency-improvement strategies such as cylinder deactivation, use of advanced materials and improved insulation to limit ambient heat loss, and turbo-compounding on the steady-state performance of the ORC system and the availability of thermal energy for downstream aftertreatment systems. Results from transient drive-cycle simulations are also presented, and we discuss strategies to address operational difficulties associated with transient drive cycles and balancing the thermal requirements of waste-heat recovery, turbocharging or turbo-compounding, and exhaust aftertreatment.

Edwards, Kevin Dean [ORNL; Wagner, Robert M [ORNL; Briggs, Thomas E [ORNL

2010-01-01T23:59:59.000Z

229

Recovery Act - Geothermal Technologies Program: Ground Source Heat Pumps Final Scientific/Technical Report  

Science Conference Proceedings (OSTI)

A large centralized geothermal heat pump system was installed to provide ice making, space cooling, space heating, process water heating, and domestic hot water heating for an ice arena in Eagan Minnesota. This paper provides information related to the design and construction of the project. Additionally, operating conditions for 12 months after start-up are provided.

Nick Rosenberry, Harris Companies

2012-05-04T23:59:59.000Z

230

Heat recovery and thermal storage : a study of the Massachusetts State Transportation Building  

E-Print Network (OSTI)

A study of the energy system at the Massachusetts State Transportation Building was conducted. This innovative energy system utilizes internal-source heat pumps and a water thermal storage system to provide building heating ...

Bjorklund, Abbe Ellen

1986-01-01T23:59:59.000Z

231

Furnace and Heat Recovery Area Design and Analysis for Conceptual Design of Supercritical O2-Based PC Boiler  

Science Conference Proceedings (OSTI)

The objective of the furnace and heat recovery area design and analysis task of the Conceptual Design of Supercritical Oxygen-Based PC Boiler study is to optimize the location and design of the furnace, burners, over-fire gas ports, and internal radiant surfaces. The furnace and heat recovery area were designed and analyzed using the FW-FIRE, Siemens, and HEATEX computer programs. The furnace is designed with opposed wall-firing burners and over-fire air ports. Water is circulated in the furnace by forced circulation to the waterwalls at the periphery and divisional wall panels within the furnace. Compared to the air-fired furnace, the oxygen-fired furnace requires only 65% of the surface area and 45% of the volume. Two oxygen-fired designs were simulated: (1) with cryogenic air separation unit (ASU) and (2) with oxygen ion transport membrane (OITM). The maximum wall heat flux in the oxygen-fired furnace is more than double that of the air-fired furnace due to the higher flame temperature and higher H{sub 2}O and CO{sub 2} concentrations. The coal burnout for the oxygen-fired case is 100% due to a 500 F higher furnace temperature and higher concentration of O{sub 2}. Because of the higher furnace wall temperature of the oxygen-fired case compared to the air-fired case, furnace water wall material was upgraded from T2 to T92. Compared to the air-fired heat recovery area (HRA), the oxygen-fired HRA total heat transfer surface is 35% less for the cryogenic design and 13% less for the OITM design due to more heat being absorbed in the oxygen-fired furnace and the greater molecular weight of the oxygen-fired flue gas. The HRA tube materials and wall thickness are nearly the same for the air-fired and oxygen-fired design since the flue gas and water/steam temperature profiles encountered by the heat transfer banks are similar.

Andrew Seltzer

2006-05-01T23:59:59.000Z

232

Waste Heat Recovery and Recycling in Thermal Separation Processes: Distillation, Multi-Effect Evaporation (MEE) and Crystallization Processes  

Science Conference Proceedings (OSTI)

Evaporation and crystallization are key thermal separation processes for concentrating and purifying inorganic and organic products with energy consumption over 1,000 trillion Btu/yr. This project focused on a challenging task of recovering low-temperature latent heat that can have a paradigm shift in the way thermal process units will be designed and operated to achieve high-energy efficiency and significantly reduce the carbon footprint as well as water footprint. Moreover, this project has evaluated the technical merits of waste-heat powered thermal heat pumps for recovery of latent heat from distillation, multi-effect evaporation (MEE), and crystallization processes and recycling into the process. The Project Team has estimated the potential energy, economics and environmental benefits with the focus on reduction in CO2 emissions that can be realized by 2020, assuming successful development and commercialization of the technology being developed. Specifically, with aggressive industry-wide applications of heat recovery and recycling with absorption heat pumps, energy savings of about 26.7 trillion Btu/yr have been estimated for distillation process. The direct environmental benefits of this project are the reduced emissions of combustible products. The estimated major reduction in environmental pollutants in the distillation processes is in CO2 emission equivalent to 3.5 billion lbs/year. Energy consumption associated with water supply and treatments can vary between 1,900 kWh and 23,700 kWh per million-gallon water depending on sources of natural waters [US DOE, 2006]. Successful implementation of this technology would significantly reduce the demand for cooling-tower waters, and thereby the use and discharge of water treatment chemicals. The Project Team has also identified and characterized working fluid pairs for the moderate-temperature heat pump. For an MEE process, the two promising fluids are LiNO3+KNO3+NANO3 (53:28:19 ) and LiNO3+KNO3+NANO2(53:35:12). And for an H2O2 distillation process, the two promising fluids are Trifluoroethanol (TFE) + Triethylene Glycol Dimethyl ether (DMETEG) and Ammonia+ Water. Thermo-physical properties calculated by Aspen+ are reasonably accurate. Documentation of the installation of pilot-plants or full commercial units were not found in the literature for validating thermo-physical properties in an operating unit. Therefore, it is essential to install a pilot-scale unit to verify thermo-physical properties of working fluid pairs and validate the overall efficiency of the thermal heat pump at temperatures typical of distillation processes. For an HO2 process, the ammonia-water heat pump system is more compact and preferable than the TFE-DMETEG heat pump. The ammonia-water heat pump is therefore recommended for the H2O2 process. Based on the complex nature of the heat recovery system, we anticipated that capital costs could make investments financially unattractive where steam costs are low, especially where co-generation is involved. We believe that the enhanced heat transfer equipment has the potential to significantly improve the performance of TEE crystallizers, independent of the absorption heat-pump recovery system. Where steam costs are high, more detailed design/cost engineering will be required to verify the economic viability of the technology. Due to the long payback period estimated for the TEE open system, further studies on the TEE system are not warranted unless there are significant future improvements to heat pump technology. For the H2O2 distillation cycle heat pump waste heat recovery system, there were no significant process constraints and the estimated 5 years payback period is encouraging. We therefore recommend further developments of application of the thermal heat pump in the H2O2 distillation process with the focus on the technical and economic viability of heat exchangers equipped with the state-of-the-art enhancements. This will require additional funding for a prototype unit to validate enhanced thermal performances of heat transfer equipment, evaluat

Emmanuel A. Dada; Chandrakant B. Panchal; Luke K. Achenie; Aaron Reichl; Chris C. Thomas

2012-12-03T23:59:59.000Z

233

Application of the VRV Air-Conditioning System Heat Recovery Series in Interior Zone and Analysis of its Energy Saving  

E-Print Network (OSTI)

To reduce the energy consumption of air conditioning systems, we can use the VRV air conditioning system to supply cold loads in the winter for rooms in the construction inner zone where cold loads need to be supplied. The VRV air-conditioning system of variable frequency technology can achieve the effect of energy conservation. In this article, we analyze the application of the VRV air conditioning system heat recovery series in the construction inner zone and its energy saving characteristics via a project example.

Zhang, Q.; Li, D.; Zhang, J.

2006-01-01T23:59:59.000Z

234

Energy recovery during expansion of compressed gas using power plant low-quality heat sources  

SciTech Connect

A method of recovering energy from a cool compressed gas, compressed liquid, vapor, or supercritical fluid is disclosed which includes incrementally expanding the compressed gas, compressed liquid, vapor, or supercritical fluid through a plurality of expansion engines and heating the gas, vapor, compressed liquid, or supercritical fluid entering at least one of the expansion engines with a low quality heat source. Expansion engines such as turbines and multiple expansions with heating are disclosed.

Ochs, Thomas L. (Albany, OR); O' Connor, William K. (Lebanon, OR)

2006-03-07T23:59:59.000Z

235

New Technology Demonstration of Microturbine with Heat Recovery at Fort Drum, New York  

SciTech Connect

This report replaces PNNL-14417 and documents a project to demonstrate and evaluate a combined heat and power-configured microturbine system.

Friedrich, Michele; Armstrong, Peter R.; Smith, David L.

2004-04-30T23:59:59.000Z

236

Repowering reheat units with gas turbines: Final report. [Adding gas turbines and heat recovery to present units  

SciTech Connect

Although conventional repowering on nonreheat units replaces existing boilers with gas turbines and heat recovery steam generators, options investigated by Virginia Power use gas turbine waste heat to supplement, rather than replace, the output of existing steam generators. Virginia Power's experience in considering feedwater heater repowering (FHR) and hot windbox repowering (HWR) as repowering options is described here. Studying five plants identified as potential repowering candidates, investigators first evaluated FHR, which uses a gas turbine generator set equipped with an economizer to heat boiler feedwater. This reduces the steam turbine extraction flow and increases the steam turbine capacity. HWR, the second method investigated, routes the hot, relatively oxygen-rich exhaust flow from a gas turbine into the boiler windbox, eliminating the need for an air preheater. A boiler stack gas cooler then heats feedwater, again increasing turbine capacity by reducing extraction steam flow requirements for feedwater heating. FHR provided the lowest installed cost, especially at Mount Storm unit 3, a coal-fired minemouth plant. Use of a gas turbine to heat feedwater at this plant resulted in a $523/kW (1985) installed cost and 124-MWe unit capacity increase at a design incremental heat rate of 8600 Btu/kWh. FHR at Mount Storm units 1, 2, and 3 cost less overall than installation and operation of a new combined cycle. Although the findings and conclusions in this series of repowering reports are largely unique to the individual plants, units, and applications studied, other utilities performing repowering studies can draw on the types of consideration entertained, alternatives examined, and factors and rationale leading to rejection or acceptance of a given repowering approach. 12 figs., 12 tabs.

Rives, J.D.; Catina, J.

1987-05-01T23:59:59.000Z

237

A Chronology of the Nashville, Tennessee Incinerator with Heat Recovery and the  

E-Print Network (OSTI)

densers and rejects the surplus heat to the chilling plant cooling tower system. Surplus steam may also disposal hopper. Bleed from the cooling towers is used for makeup to the scrubber recirculation system Heating and Cooling Facility MAURICE J. WILSON I. C. Thomasson & Associates, 1 nco Nashville, Tennessee

Columbia University

238

Technical Subtopic 2.1: Modeling Variable Refrigerant Flow Heat Pump and Heat Recovery Equipment in EnergyPlus  

Science Conference Proceedings (OSTI)

The University of Central Florida/Florida Solar Energy Center, in cooperation with the Electric Power Research Institute and several variable-refrigerant-flow heat pump (VRF HP) manufacturers, provided a detailed computer model for a VRF HP system in the United States Department of Energy's (U.S. DOE) EnergyPlus? building energy simulation tool. Detailed laboratory testing and field demonstrations were performed to measure equipment performance and compare this performance to both the manufacturer's data and that predicted by the use of this new model through computer simulation. The project goal was to investigate the complex interactions of VRF HP systems from an HVAC system perspective, and explore the operational characteristics of this HVAC system type within a laboratory and real world building environment. Detailed laboratory testing of this advanced HVAC system provided invaluable performance information which does not currently exist in the form required for proper analysis and modeling. This information will also be useful for developing and/or supporting test standards for VRF HP systems. Field testing VRF HP systems also provided performance and operational information pertaining to installation, system configuration, and operational controls. Information collected from both laboratory and field tests were then used to create and validate the VRF HP system computer model which, in turn, provides architects, engineers, and building owners the confidence necessary to accurately and reliably perform building energy simulations. This new VRF HP model is available in the current public release version of DOE?s EnergyPlus software and can be used to investigate building energy use in both new and existing building stock. The general laboratory testing did not use the AHRI Standard 1230 test procedure and instead used an approach designed to measure the field installed full-load operating performance. This projects test methodology used the air enthalpy method where relevant air-side parameters were controlled while collecting output performance data at discreet points of steady-state operation. The primary metrics include system power consumption and zonal heating and cooling capacity. Using this test method, the measured total cooling capacity was somewhat lower than reported by the manufacturer. The measured power was found to be equal to or greater than the manufacturers indicated power. Heating capacity measurements produced similar results. The air-side performance metric was total cooling and heating energy since the computer model uses those same metrics as input to the model. Although the sensible and latent components of total cooling were measured, they are not described in this report. The test methodology set the thermostat set point temperature very low for cooling and very high for heating to measure full-load performance and was originally thought to provide the maximum available capacity. Manufacturers stated that this test method would not accurately measure performance of VRF systems which is now believed to be a true statement. Near the end of the project, an alternate test method was developed to better represent VRF system performance as if field installed. This method of test is preliminarily called the Load Based Method of Test where the load is fixed and the indoor conditions and unit operation are allowed to fluctuate. This test method was only briefly attempted in a laboratory setting but does show promise for future lab testing. Since variable-speed air-conditioners and heat pumps include an on-board control algorithm to modulate capacity, these systems are difficult to test. Manufacturers do have the ability to override internal components to accommodate certification procedures, however, it is unknown if the resulting operation is replicated in the field, or if so, how often. Other studies have shown that variable-speed air-conditioners and heat pumps do out perform their single-speed counterparts though these field studies leave as many questions as they do provide answers. The measure

Raustad, Richard; Nigusse, Bereket; Domitrovic, Ron

2013-09-30T23:59:59.000Z

239

Recovery Act: Finite Volume Based Computer Program for Ground Source Heat Pump Systems  

SciTech Connect

This report is a compilation of the work that has been done on the grant DE-EE0002805 entitled ���¢��������Finite Volume Based Computer Program for Ground Source Heat Pump Systems.���¢������� The goal of this project was to develop a detailed computer simulation tool for GSHP (ground source heat pump) heating and cooling systems. Two such tools were developed as part of this DOE (Department of Energy) grant; the first is a two-dimensional computer program called GEO2D and the second is a three-dimensional computer program called GEO3D. Both of these simulation tools provide an extensive array of results to the user. A unique aspect of both these simulation tools is the complete temperature profile information calculated and presented. Complete temperature profiles throughout the ground, casing, tube wall, and fluid are provided as a function of time. The fluid temperatures from and to the heat pump, as a function of time, are also provided. In addition to temperature information, detailed heat rate information at several locations as a function of time is determined. Heat rates between the heat pump and the building indoor environment, between the working fluid and the heat pump, and between the working fluid and the ground are computed. The heat rates between the ground and the working fluid are calculated as a function time and position along the ground loop. The heating and cooling loads of the building being fitted with a GSHP are determined with the computer program developed by DOE called ENERGYPLUS. Lastly COP (coefficient of performance) results as a function of time are provided. Both the two-dimensional and three-dimensional computer programs developed as part of this work are based upon a detailed finite volume solution of the energy equation for the ground and ground loop. Real heat pump characteristics are entered into the program and used to model the heat pump performance. Thus these computer tools simulate the coupled performance of the ground loop and the heat pump. The price paid for the three-dimensional detail is the large computational times required with GEO3D. The computational times required for GEO2D are reasonable, a few minutes for a 20 year simulation. For a similar simulation, GEO3D takes days of computational time. Because of the small simulation times with GEO2D, a number of attractive features have been added to it. GEO2D has a user friendly interface where inputs and outputs are all handled with GUI (graphical user interface) screens. These GUI screens make the program exceptionally easy to use. To make the program even easier to use a number of standard input options for the most common GSHP situations are provided to the user. For the expert user, the option still exists to enter their own detailed information. To further help designers and GSHP customers make decisions about a GSHP heating and cooling system, cost estimates are made by the program. These cost estimates include a payback period graph to show the user where their GSHP system pays for itself. These GSHP simulation tools should be a benefit to the advancement of GSHP system

James A Menart, Professor

2013-02-22T23:59:59.000Z

240

CALTECH SUSTAINABILITY CALTECH ENERGY PORTFOLIO  

E-Print Network (OSTI)

and Distribution · Cogeneration Heat Recovery Steam Generator (HRSG) capacity: 44,500 lbs per hour steam at 300 Psig · #3 Boiler: 58,000 lbs per hour steam at 285 Psig · Steam distribution to campus at 55-65 Psig · Heat Recovery Steam Generator (HRSG) · 2.5 MW Steam Turbine Generator (STG) · Operates on natural gas

Goddard III, William A.

Note: This page contains sample records for the topic "hrsg heat recovery" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Anomalous recovery of damped radial modes in a circular?sector duct with locally heated flow  

Science Conference Proceedings (OSTI)

It is often desirable to predict acoustic propagation in a circular duct carrying a locally heated flow. Common examples include jet engines and certain industrial and commercial burners whose combustion?related noise can be an environmental problem if allowed to penetrate into the surroundings. In these cases axial gradients in the steady flow variables

J. R. Maham; S.?Y. Yeh

1984-01-01T23:59:59.000Z

242

Feasibility of Thermoelectrics for Waste Heat Recovery in Hybrid Vehicles: Preprint  

DOE Green Energy (OSTI)

Using advanced materials, thermoelectric conversion of efficiencies on the order of 20% may be possible in the near future. Thermoelectric generators offer potential to increase vehicle fuel economy by recapturing a portion of the waste heat from the engine exhaust and generating electricity to power vehicle accessory or traction loads.

Smith, K.; Thornton, M.

2007-12-01T23:59:59.000Z

243

Recovery of Water from Boiler Flue Gas Using Condensing Heat Exchangers ProMIS/Project No.: DE-NT0005648  

NLE Websites -- All DOE Office Websites (Extended Search)

Edward Levy Edward Levy Principal Investigator Director, Lehigh University Energy Research Center RecoveRy of WateR fRom BoileR flue Gas usinG condensinG Heat excHanGeRs PRomis/PRoject no.: de-nt0005648 Background As the United States' population grows and demand for electricity and water increases, power plants located in some parts of the country will find it increasingly difficult to obtain the large quantities of water needed to maintain operations. Most of the water used in a thermoelectric power plant is used for cooling, and the U.S. Department of Energy (DOE) has been focusing on possible techniques to reduce the amount of fresh water needed for cooling. Many coal-fired power plants operate with stack temperatures in the 300 °F range to minimize fouling and corrosion problems due to sulfuric acid condensation and to

244

Battleground Energy Recovery Project  

Science Conference Proceedings (OSTI)

In October 2009, the project partners began a 36-month effort to develop an innovative, commercial-scale demonstration project incorporating state-of-the-art waste heat recovery technology at Clean Harbors, Inc., a large hazardous waste incinerator site located in Deer Park, Texas. With financial support provided by the U.S. Department of Energy, the Battleground Energy Recovery Project was launched to advance waste heat recovery solutions into the hazardous waste incineration market, an area that has seen little adoption of heat recovery in the United States. The goal of the project was to accelerate the use of energy-efficient, waste heat recovery technology as an alternative means to produce steam for industrial processes. The project had three main engineering and business objectives: Prove Feasibility of Waste Heat Recovery Technology at a Hazardous Waste Incinerator Complex; Provide Low-cost Steam to a Major Polypropylene Plant Using Waste Heat; and ď?· Create a Showcase Waste Heat Recovery Demonstration Project.

Daniel Bullock

2011-12-31T23:59:59.000Z

245

" "," ",,," Steam Turbines Supplied by Either Conventional or Fluidized Bed Boilers",,,"Conventional Combusion Turbines with Heat Recovery",,,"Combined-Cycle Combusion Turbines",,,"Internal Combusion Engines with Heat Recovery",,," Steam Turbines Supplied by Heat Recovered from High-Temperature Processes",,,," "  

U.S. Energy Information Administration (EIA) Indexed Site

3 Relative Standard Errors for Table 8.3;" 3 Relative Standard Errors for Table 8.3;" " Unit: Percents." " "," ",,," Steam Turbines Supplied by Either Conventional or Fluidized Bed Boilers",,,"Conventional Combusion Turbines with Heat Recovery",,,"Combined-Cycle Combusion Turbines",,,"Internal Combusion Engines with Heat Recovery",,," Steam Turbines Supplied by Heat Recovered from High-Temperature Processes",,,," " " "," " ," " "NAICS Code(a)","Subsector and Industry","Establishments(b)","Establishments with Any Cogeneration Technology in Use(c)","In Use(d)","Not in Use","Don't Know","In Use(d)","Not in Use","Don't Know","In Use(d)","Not in Use","Don't Know","In Use(d)","Not in Use","Don't Know","In Use(d)","Not in Use","Don't Know"

246

Reduced energy consumption by massive thermoelectric waste heat recovery in light duty trucks  

Science Conference Proceedings (OSTI)

The main objective of the EC funded HEATRECAR project is to reduce the energy consumption and curb CO2 emissions of vehicles by massively harvesting electrical energy from the exhaust system and re-use this energy to supply electrical components within the vehicle or to feed the power train of hybrid electrical vehicles. HEATRECAR is targeting light duty trucks and focuses on the development and the optimization of a Thermo Electric Generator (TEG) including heat exchanger

D. Magnetto; G. Vidiella

2012-01-01T23:59:59.000Z

247

Base-Load and Peak Electricity from a Combined Nuclear Heat and Fossil Combined-Cycle Plant  

SciTech Connect

A combined-cycle power plant is proposed that uses heat from a high-temperature reactor and fossil fuel to meet base-load and peak electrical demands. The high temperature gas turbine produces shaft power to turn an electric generator. The hot exhaust is then fed to a heat recovery steam generator (HRSG) that provides steam to a steam turbine for added electrical power production. A simplified computational model of the thermal power conversion system was developed in order to parametrically investigate two different steady-state operation conditions: base load nuclear heat only from an Advanced High Temperature Reactor (AHTR), and combined nuclear heat with fossil heat to increase the turbine inlet temperature. These two cases bracket the expected range of power levels, where any intermediate power level can result during electrical load following. The computed results indicate that combined nuclear-fossil systems have the potential to offer both low-cost base-load electricity and lower-cost peak power relative to the existing combination of base-load nuclear plants and separate fossil-fired peak-electricity production units. In addition, electric grid stability, reduced greenhouse gases, and operational flexibility can also result with using the conventional technology presented here for the thermal power conversion system coupled with the AHTR. (authors)

Conklin, James C.; Forsberg, Charles W. [Oak Ridge National Laboratory, P.O. Box 2008, Oak Ridge, TN 37831 (United States)

2007-07-01T23:59:59.000Z

248

Base-Load and Peak Electricity from a Combined Nuclear Heat and Fossil Combined-Cycle Plant  

Science Conference Proceedings (OSTI)

A combined-cycle power plant is proposed that uses heat from a high-temperature reactor and fossil fuel to meet base-load and peak electrical demands. The high-temperature gas turbine produces shaft power to turn an electric generator. The hot exhaust is then fed to a heat recovery steam generator (HRSG) that provides steam to a steam turbine for added electrical power production. A simplified computational model of the thermal power conversion system was developed in order to parametrically investigate two different steady-state operation conditions: base load nuclear heat only from an Advanced High Temperature Reactor (AHTR), and combined nuclear heat with fossil heat to increase the turbine inlet temperature. These two cases bracket the expected range of power levels, where any intermediate power level can result during electrical load following. The computed results indicate that combined nuclear-fossil systems have the potential to offer both low-cost base-load electricity and lower-cost peak power relative to the existing combination of base-load nuclear plants and separate fossil-fired peak-electricity production units. In addition, electric grid stability, reduced greenhouse gases, and operational flexibility can also result with using the conventional technology presented here for the thermal power conversion system coupled with the AHTR.

Conklin, Jim [ORNL; Forsberg, Charles W [ORNL

2007-01-01T23:59:59.000Z

249

OpenEI Community - natural gas+ condensing flue gas heat recovery+ water  

Open Energy Info (EERE)

Increase Natural Gas Increase Natural Gas Energy Efficiency http://en.openei.org/community/group/increase-natural-gas-energy-efficiency Description: Increased natural gas energy efficiency = Reduced utility bills = Profit In 2011 the EIA reports that commercial buildings, industry and the power plants consumed approx. 17.5 Trillion cu.ft. of natural gas.How much of that energy was wasted, blown up chimneys across the country as HOT exhaust into the atmosphere? 40% ~ 60% ? At what temperature?read more natural gas+ condensing flue gas heat

250

Thermal engine driven heat pump for recovery of volatile organic compounds  

DOE Patents (OSTI)

The present invention relates to a method and apparatus for separating volatile organic compounds from a stream of process gas. An internal combustion engine drives a plurality of refrigeration systems, an electrical generator and an air compressor. The exhaust of the internal combustion engine drives an inert gas subsystem and a heater for the gas. A water jacket captures waste heat from the internal combustion engine and drives a second heater for the gas and possibly an additional refrigeration system for the supply of chilled water. The refrigeration systems mechanically driven by the internal combustion engine effect the precipitation of volatile organic compounds from the stream of gas.

Drake, Richard L. (Schenectady, NY)

1991-01-01T23:59:59.000Z

251

System study on partial gasification combined cycle with CO{sub 2} recovery - article no. 051801  

Science Conference Proceedings (OSTI)

S partial gasification combined cycle with CO{sub 2} recovery is proposed in this paper. Partial gasification adopts cascade conversion of the composition of coal. Active composition of coal is simply gasified, while inactive composition, that is char, is burnt in a boiler. Oxy-fuel combustion of syngas produces only CO{sub 2} and H{sub 2}O, so the CO{sub 2} can be separated through cooling the working fluid. This decreases the amount of energy consumption to separate CO{sub 2} compared with conventional methods. The novel system integrates the above two key technologies by injecting steam from a steam turbine into the combustion chamber of a gas turbine to combine the Rankine cycle with the Brayton cycle. The thermal efficiency of this system will be higher based on the cascade utilization of energy level. Compared with the conventional integrated gasification combined cycle (IGCC), the compressor of the gas turbine, heat recovery steam generator (HRSG) and gasifier are substituted for a pump, reheater, and partial gasifier, so the system is simplified. Furthermore, the novel system is investigated by means of energy-utilization diagram methodology and provides a simple analysis of their economic and environmental performance. As a result, the thermal efficiency of this system may be expected to be 45%, with CO{sub 2} recovery of 41.2%, which is 1.5-3.5% higher than that of an IGCC system. At the same time, the total investment cost of the new system is about 16% lower than that of an IGCC. The comparison between the partial gasification technology and the IGCC technology is based on the two representative cases to identify the specific feature of the proposed system.

Xu, Y.J.; Jin, H.G.; Lin, R.M.; Han, W. [Chinese Academy of Science, Beijing (China)

2008-09-15T23:59:59.000Z

252

Waste Heat Reduction and Recovery for Improving Furnace Efficiency, Productivity and Emissions Performance: A BestPractices Process Heating Technical Brief  

DOE Green Energy (OSTI)

This technical brief is a guide to help plant operators reduce waste heat losses associated with process heating equipment.

Not Available

2004-11-01T23:59:59.000Z

253

Investigating potential efficiency improvement for light-duty transportation applications through simulation of an organic Rankine cycle for waste-heat recovery  

SciTech Connect

Modern diesel engines used in light-duty transportation applications have peak brake thermal efficiencies in the range of 40-42% for high-load operation with substantially lower efficiencies at realistic road-load conditions. Thermodynamic energy and exergy analysis reveals that the largest losses from these engines are due to heat loss and combustion irreversibility. Substantial improvement in overall engine efficiency requires reducing or recovering these losses. Unfortunately, much of the heat transfer either occurs at relatively low temperatures resulting in large entropy generation (such as in the air-charge cooler), is transferred to low-exergy flow streams (such as the oil and engine coolant), or is radiated or convected directly to the environment. While there are significant opportunities for recovery from the exhaust and EGR cooler for heavy-duty applications, the potential benefits of such a strategy for light-duty applications are unknown due to transient operation, low-load operation at typical driving conditions, and the added mass of the system. We have developed an organic Rankine cycle model using GT-Suite to investigate the potential for efficiency improvement through waste-heat recovery from the exhaust and EGR cooler of a light-duty diesel engine. Results from steady-state and drive-cycle simulations are presented, and we discuss strategies to address operational difficulties associated with transient drive cycles and competition between waste-heat recovery systems, turbochargers, aftertreatment devices, and other systems for the limited thermal resources.

Edwards, Kevin Dean [ORNL; Wagner, Robert M [ORNL

2010-01-01T23:59:59.000Z

254

Cyanidation Recovery Process  

Science Conference Proceedings (OSTI)

Heat Treatment of Black Dross for the Production of a Value Added Material ... Leaching Studies for Metals Recovery from Waste Printed Wiring Boards (PWBs).

255

Waste Heat Recovery Modellering.  

E-Print Network (OSTI)

?? SammanfattningI ett tidigare projekt, utfört under vĺren 2010, modellerades och simulerades en ĺnggenerator i GT-SUITE för att analysera och jämföra dess resultat med de… (more)

Rojas Tena, Fernando

2011-01-01T23:59:59.000Z

256

Lighting a building with a single bulb : toward a system for illumination in the 21st c.; or, A centralized illumination system for the efficient decoupling and recovery of lighting related heat  

E-Print Network (OSTI)

Piping light represents the first tenable method for recovery and reutilization of lighting related heat. It can do this by preserving the energy generated at the lamp as radiative, departing from precedent and avoiding ...

Levens, Kurt Antony, 1961-

1997-01-01T23:59:59.000Z

257

Design and Analysis on Energy Recovery System of Aquatic Product Comprehensive Process Factory  

Science Conference Proceedings (OSTI)

To reduce energy consumption and carbon emission, this paper designs energy recovery technology of aquatic products processing plant, including refrigeration heat recovery and ice-making cooling recovery. Three heat recovery plans are compared and analyzed, ... Keywords: aquatic products, sensible heat recovery, heat recovery efficiency, cooling recovery

Min Li; Zhan Li; Xiaoqiang Jiang; Zhongjin Zhang; Lijin Zheng

2009-10-01T23:59:59.000Z

258

Pre-Procurement Technical Due Diligence Guideline -- Existing HRSGs  

Science Conference Proceedings (OSTI)

The dynamic and competitive nature of the power generation market sometimes presents Electric Power Research Institute (EPRI) members with the opportunity to procure an existing combined-cycle plant or heat recovery steam generator (HRSG). The potential for the HRSG to deliver suitably reliable service at reasonable maintenance expense depends on design details of key pressure parts and the maintenance, ...

2012-12-12T23:59:59.000Z

259

INTERNATIONAL Presented by  

E-Print Network (OSTI)

This presentation..... MVPP #12; Fuel is burned to drive a gas turbine The gas turbine drives a generator Hot exhaust from the gas turbine is sent to a Heat Recovery Steam Generator (HRSG) The steam turbine drives Steam HRSG Air Fuel Gas Turbine & Generator Cooling Water #12;Plant Output MVPP Gas Turbine A Gas

Keller, Arturo A.

260

Recovery Act - Geothermal Technologies Program:Ground Source...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Recovery Act - Geothermal Technologies Program:Ground Source Heat Pumps Recovery Act - Geothermal Technologies Program:Ground Source Heat Pumps A detailled description of the...

Note: This page contains sample records for the topic "hrsg heat recovery" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Early Tube Leak Detection in a HRSG Application Using Acoustic Monitoring Technology  

Science Conference Proceedings (OSTI)

Acoustic monitoring has become an essential part of early tube leak detection for conventional boilers. Acoustic monitoring is intended for steam leak detection in pressurized vessels, including power boilers, recovery boilers, and feedwater heaters. The system performs acoustic monitoring by continuously measuring the internal sounds from the boiler, signaling an alarm when the sound exceeds a preset threshold for a ...

2012-12-12T23:59:59.000Z

262

Simulation aids cogeneration system analysis  

Science Conference Proceedings (OSTI)

Cogeneration systems using gas turbines and heat-recovery steam generators (HRSGs) are widely used in chemical process industries (CPI) plants. Because these plants are quite expensive and the HRSG is an important part of the system, it is prudent to analyze the heat-recovery system or simulate its performance well in advance of finalizing plant specifications. Simulation is a method of predicting the performance of the HRSG under different operating modes and gas and steam conditions without physically designing the equipment. Such a study will provide the engineer with valuable information about the HRSG and its performance capabilities. The simulation results could influence the choice of steam system parameters and the selection of the steam or gas turbine. In addition, one may also obtain information about the performance of the HRSG and the cogeneration system. This article explains what HRSG simulation is and the basic methodology. Its applications are then illustrated through several examples.

Ganapathy, V.

1993-10-01T23:59:59.000Z

263

Combined cycle electric power plant and a heat recovery steam generator having improved boiler feed pump flow control  

SciTech Connect

A combined cycle electric power plant is described that includes gas and steam turbines and a steam generator for recovering the heat in the exhaust gases exited from the gas turbine and for using the recovered heat to produce and supply steam to the steam turbine. The steam generator includes an economizer tube and a high pressure evaporator tube and a boiler feed pump for directing the heat exchange fluid serially through the aforementioned tubes. A condenser is associated with the steam turbine for converting the spent steam into condensate water to be supplied to a deaerator for removing undesired air and for preliminarily heating the water condensate before being pumped to the economizer tube. Condensate flow through the economizer tube is maintained substantially constant by maintaining the boiler feed pump at a predetermined, substantially constant rate. A bypass conduit is provided to feed back a portion of the flow heated in the economizer tube to the deaerator; the portion being equal to the difference between the constant flow through the economizer tube and the flow to be directed through the high pressure evaporator tube as required by the steam turbine for its present load.

Martz, L.F.; Plotnick, R.J.

1976-06-29T23:59:59.000Z

264

Corrosive resistant heat exchanger  

DOE Patents (OSTI)

A corrosive and errosive resistant heat exchanger which recovers heat from a contaminated heat stream. The heat exchanger utilizes a boundary layer of innocuous gas, which is continuously replenished, to protect the heat exchanger surface from the hot contaminated gas. The innocuous gas is conveyed through ducts or perforations in the heat exchanger wall. Heat from the heat stream is transferred by radiation to the heat exchanger wall. Heat is removed from the outer heat exchanger wall by a heat recovery medium.

Richlen, Scott L. (Annandale, VA)

1989-01-01T23:59:59.000Z

265

Energy integrated dairy farm system in Georgia: Technical manual, Mathis/P and M Dairy Farm, Social Circle, Georgia. [Cogeneration using biogas; heat recovery  

SciTech Connect

This manual describes a project sponsored to optimize energy generation and utilization in the agricultural or food processing industry. The particular project involves the Mathis/P and M Dairy Farm located in Social Circle, Georgia (about 60 miles east of Atlanta). The farm is designed for a 550 milking cow herd and produces certified raw milk for sale to a processing plant located in Atlanta. The project converted the Mathis/P and and M Dairy into an energy integrated dairy farm system (EIDFS) in which the interaction of the subsystems and components are modified such that the energy resources of the farm are optimized. This manual is a description of the system, subsystems and components composing the Mathis EIDFS and is primarily intended for farmers, extension agents, and equipment manufacturers who might be involved in future EIDFS projects. Cogeneration using biogas from manures and heat recovery from the refrigeration machinery were among the options chosen.

Walsh, J.L. Jr.; Ross, C.C.; Lamade, R.M.

1986-09-01T23:59:59.000Z

266

Final Report: Modifications and Optimization of the Organic Rankine Cycle to Improve the Recovery of Waste Heat  

Science Conference Proceedings (OSTI)

This research and development (R&D) project exemplifies a shared public private commitment to advance the development of energy efficient industrial technologies that will reduce the U.S. dependence upon foreign oil, provide energy savings and reduce greenhouse gas emissions. The purpose of this project was to develop and demonstrate a Direct Evaporator for the Organic Rankine Cycle (ORC) for the conversion of waste heat from gas turbine exhaust to electricity. In conventional ORCs, the heat from the exhaust stream is transferred indirectly to a hydrocarbon based working fluid by means of an intermediate thermal oil loop. The Direct Evaporator accomplishes preheating, evaporation and superheating of the working fluid by a heat exchanger placed within the exhaust gas stream. Direct Evaporation is simpler and up to 15% less expensive than conventional ORCs, since the secondary oil loop and associated equipment can be eliminated. However, in the past, Direct Evaporation has been avoided due to technical challenges imposed by decomposition and flammability of the working fluid. The purpose of this project was to retire key risks and overcome the technical barriers to implementing an ORC with Direct Evaporation. R&D was conducted through a partnership between the Idaho National Laboratory (INL) and General Electric (GE) Global Research Center (GRC). The project consisted of four research tasks: (1) Detailed Design & Modeling of the ORC Direct Evaporator, (2) Design and Construction of Partial Prototype Direct Evaporator Test Facility, (3) Working Fluid Decomposition Chemical Analyses, and (4) Prototype Evaluation. Issues pertinent to the selection of an ORC working fluid, along with thermodynamic and design considerations of the direct evaporator, were identified. The FMEA (Failure modes and effects analysis) and HAZOP (Hazards and operability analysis) safety studies performed to mitigate risks are described, followed by a discussion of the flammability analysis of the direct evaporator. A testbed was constructed and the prototype demonstrated at the GE GRC Niskayuna facility.

Donna Post Guillen; Jalal Zia

2013-09-01T23:59:59.000Z

267

Preliminary market analysis for Brayton cycle heat recovery system characterization program. Subtask 5. 2 of phase I program plan  

Science Conference Proceedings (OSTI)

The purpose of the task is to determine the market potential of the Brayton-cycle Subatmospheric System (SAS), especially as applied to the glass processing industry. Areas which impact the sales of the Brayton-cycle systems examined are: market size; opportunities for waste heat system installation (furnace rebuild and repair); pollution control on glass furnaces; equipment costs; equipment performance; and market growth potential. Supporting data were compiled for the glass industry inventory and are presented in Appendix A. Emission control techniques in the glass industry are discussed in Appendix B. (MCW)

Not Available

1980-08-31T23:59:59.000Z

268

Heat recovery subsystem and overall system integration of fuel cell on-site integrated energy systems. Final report  

DOE Green Energy (OSTI)

The overall objective of this project was to determine the best HVAC (heating, ventilating and air conditioning) subsystem to interface with the Engelhard fuel cell system for application in commercial buildings. To accomplish this objective, the effects of several system and site specific parameters on the economic feasibility of fuel cell/HVAC systems were investigated. The fuel cell system provides electricity for an electric water chiller and for domestic electric needs. Supplemental electricity is purchased from the utility if needed. An excess of electricity generated by the fuel cell system can be sold to the utility. The fuel cell system also provides thermal energy which can be used for absorption cooling, space heating and domestic hot water. Thermal storage can be incorporated into the system. Thermal energy is also provided by an auxiliary boiler if needed to supplement the fuel cell system output. Fuel cell/HVAC systems were analyzed with the TRACE computer program. TRACE is an energy and economic analysis program that has been developed by The Trane Company. Results are detailed. (WHK)

Mougin, L.J.

1983-07-15T23:59:59.000Z

269

Feasibility Study for the Ivano-Frankivsk District Heating Repowering: Analysis of Options  

Science Conference Proceedings (OSTI)

Part of the U.S. Initiative on Joint Implementation with the Ukraine Inter-Ministerial Commission on Climate Change, financed by the US Department of Energy. The project was implemented by a team consisting of the US company SenTech, Inc. and the Ukrainian company Esco-West. The main objective of the effort was to assess available alternatives of Ivano-Frankivsk (I-F) District Heating repowering and provide information for I-F's investment decision process. This study provides information on positive and negative technical and economic aspects of available options. Three options were analyzed for technical merit and economic performance: 1. Installation of cogeneration system based on Gas Turbine (GT) and Heat Recovery Heat Exchanger with thermal capacity of 30 MW and electrical capacity of 13.5 MW. This Option assumes utilization of five existing boilers with total capacity of 221 MW. Existing boilers will be equipped with modern controls. Equipment in this Option was sized for longest operating hours, about 8000 based on the available summer baseload. 2. Installation of Gas Turbine Combined Cycle (GTCC) and Heat Recovery Steam Generator (HRSG) with thermal capacity 45 MW and electrical capacity of 58.7 MW. This Option assumes utilization of five existing boilers with total capacity of 221 MW. Existing boilers will be equipped with modern controls. The equipment was sized for medium, shoulder season thermal load, and some cooling was assumed during the summer operation for extension of operating hours for electricity production. 3. Retrofit of six existing boilers (NGB) with total thermal capacity of 255.9 MW by installation of modern control system and minor upgrades. This option assumes only heat production with minimum investment. The best economic performance and the largest investment cost would result from alternative GTCC. This alternative has positive Net Present Value (NPV) with discount rate lower than about 12%, and has IRR slightly above 12%. The lowest economic results, and the lowest required investment, would result from alternative NGB. This Option's NPV is negative even at 0% discount rate, and would not become positive even by improving some parameters within a reasonable range. The Option with Gas Turbine displays relatively modest results and the NPV is positive for low discount rate, higher price of sold electricity and lower cost of natural gas. The IRR of this alternative is 9.75%, which is not very attractive. The largest influences on the investment are from the cost of electricity sold to the grid, the heat tariff, and the cost of natural gas. Assuming the implementation of the GTCC alternative, the benefit of the project is also reflected in lower Green House Emissions.

Markel, L.; Popelka, A.; Laskarevsky, V.

2002-03-20T23:59:59.000Z

270

THERMAL RECOVERY  

NLE Websites -- All DOE Office Websites (Extended Search)

THERMAL RECOVERY Thermal recovery comprises the techniques of steamflooding, cyclic steam stimulation, and in situ combustion. In steamflooding, high-temperature steam is injected...

271

Secretary Chu Announces Nearly $50 Million of Recovery Act Funding...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Chu Announces Nearly 50 Million of Recovery Act Funding to Accelerate Deployment of Geothermal Heat Pumps Secretary Chu Announces Nearly 50 Million of Recovery Act Funding to...

272

Advanced Organic Vapor Cycles for Improving Thermal Conversion Efficiency in Renewable Energy Systems  

E-Print Network (OSTI)

profiles for a dual pressure HRSG. Reprinted with permissionRecovery Steam Generator (HRSG) is high, which is often thecosts, single pressure HRSG may also be used; however, the

Ho, Tony

2012-01-01T23:59:59.000Z

273

Enhanced geothermal systems (EGS) with CO2 as heat transmission fluid--A scheme for combining recovery of renewable energy with geologic storage of CO2  

E-Print Network (OSTI)

Approach for Generating Renewable Energy with SimultaneousCombining Recovery of Renewable Energy with Geologic Storageof this abundant and renewable resource, geothermal energy

Pruess, K.

2010-01-01T23:59:59.000Z

274

Heat Recovery in Building Envelopes  

E-Print Network (OSTI)

glass fiber insulation), an exterior plywood sheathing andan interior plywood layer. The cross-section of a

Sherman, Max H.; Walker, Iain S.

2001-01-01T23:59:59.000Z

275

Werner Rösener (Hrsg.): - Springer  

Science Conference Proceedings (OSTI)

49 8 Buchbesprechungen. Werner Rösener (I-Irsg.): Kommunikation in der ländlichen Gesellschaft vom Mittelalter bis zur. Moderne. — Göttingen: Vandenhoeck ...

276

Moritz Föllmer (Hrsg.): Sehnsucht ...  

Science Conference Proceedings (OSTI)

S02 Buchbesprechungen schen Fundes entwickelt werden. Sie wirken eher ad hoc formuliert, teilweise unzusammenhän- gend und in ihrer theoretischen ...

277

Categorical Exclusion Determinations: American Recovery and Reinvestme...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

September 28, 2010 CX-004168: Categorical Exclusion Determination Modeling Variable Refrigerant Flow Heat Pump and Heat Recovery Equipment in EnergyPlus CX(s) Applied: A1, A9,...

278

Assessment of the Need to Chemical Clean  

Science Conference Proceedings (OSTI)

Operational chemical cleaning criteria for heat recovery steam generators (HRSG) are currently based on those applicable to conventional radiant boilers. However, the design and operating conditions in HRSG differ considerably from those of conventional boilers. Thus there is a need to evaluate whether the current criteria for operational cleans are suitable and to consider if alternative and/or supplemental criteria are applicable. A potentially significant issue with regard to the need for chemical cle...

2005-11-22T23:59:59.000Z

279

Guidelines for Makeup Water Treatment  

Science Conference Proceedings (OSTI)

The quality of boiler and heat recovery steam generator HRSG cycle makeup water is central to ensuring the necessary purity of boiler or HRSG water, feedwater, and steam. It plays an important role in ensuring component availability and reliability in fossil and combined cycle plants. This report presents up-to-date guidelines based on proven approaches for producing makeup water from various raw water supplies. Major losses of availability in fossil fuel plants are attributable to water and steam contam...

2010-12-23T23:59:59.000Z

280

In high-tech industries, large amounts of reliable, high-quality  

E-Print Network (OSTI)

with the grid, three reciprocating engines, two absorption chillers, and a heat recovery steam generator (HRSGW natural gas-fired fuel cells · Two 70-ton Thermax LiBr absorption chillers · One unfired heat recovery, absorption chillers, and a HRSG. DISTRIBUTED ENERGY PROGRAM PROJECT PROFILE #12;Distributed Energy Project

Note: This page contains sample records for the topic "hrsg heat recovery" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Waste Steam Recovery  

E-Print Network (OSTI)

An examination has been made of the recovery of waste steam by three techniques: direct heat exchange to process, mechanical compression, and thermocompression. Near atmospheric steam sources were considered, but the techniques developed are equally applicable to other sources of steam. The interaction of the recovery system with the plant's steam/power system has been included. Typical operating economics have been prepared. It was found that the profitability of most recovery schemes is generally dependent on the techniques used, the existing steam/power system, and the relative costs of steam and power. However, there will always be site-specific factors to consider. It is shown that direct heat exchange and thermocompression will always yield an energy profit when interacting with PRVs in the powerhouse. A set of typical comparisons between the three recovery techniques, interacting with various powerhouse and plant steam system configurations, is presented. A brief outline of the analysis techniques needed to prepare the comparison is also shown. Only operating costs are examined; capital costs are so size - and site-specific as to be impossible to generalize. The operating cost savings may be used to give an indication of investment potential.

Kleinfeld, J. M.

1979-01-01T23:59:59.000Z

282

Enhanced oil recovery system  

DOE Patents (OSTI)

All energy resources available from a geopressured geothermal reservoir are used for the production of pipeline quality gas using a high pressure separator/heat exchanger and a membrane separator, and recovering waste gas from both the membrane separator and a low pressure separator in tandem with the high pressure separator for use in enhanced oil recovery, or in powering a gas engine and turbine set. Liquid hydrocarbons are skimmed off the top of geothermal brine in the low pressure separator. High pressure brine from the geothermal well is used to drive a turbine/generator set before recovering waste gas in the first separator. Another turbine/generator set is provided in a supercritical binary power plant that uses propane as a working fluid in a closed cycle, and uses exhaust heat from the combustion engine and geothermal energy of the brine in the separator/heat exchanger to heat the propane.

Goldsberry, Fred L. (Spring, TX)

1989-01-01T23:59:59.000Z

283

Woven heat exchanger  

DOE Patents (OSTI)

This invention relates to a heat exchanger for waste heat recovery from high temperature industrial exhaust streams. In a woven ceramic heat exchanger using the basic tube-in-shell design, each heat exchanger consisting of tube sheets and tube, is woven separately. Individual heat exchangers are assembled in cross-flow configuration. Each heat exchanger is woven from high temperature ceramic fiber, the warp is continuous from tube to tube sheet providing a smooth transition and unitized construction.

Piscitella, R.R.

1984-07-16T23:59:59.000Z

284

Effects of a shortened depreciation schedule on the investment costs for combined heat and power  

E-Print Network (OSTI)

Recovery Steam Generators Water Treatment System Electricalapplicable), heat recovery steam generators, water treatmentMW Combustion Turbines Steam Turbine Generators Heat

Kranz, Nicole; Worrell, Ernst

2001-01-01T23:59:59.000Z

285

Development and Evaluation of Brazed Joints for a Plate Microchnanel Heat Exchanger.  

E-Print Network (OSTI)

??A brazing method is developed for high efficiency microchannel heat plate heat exchangers for waste heat recovery. Prototype elements for these heat exchangers are fabricated… (more)

Craymer, Kenneth L.

2011-01-01T23:59:59.000Z

286

Efficiency combined cycle power plant  

SciTech Connect

This patent describes a method of operating a combined cycle power plant. It comprises: flowing exhaust gas from a combustion turbine through a heat recovery steam generator (HRSG); flowing feed water through an economizer section of the HRSG at a flow rate and providing heated feed water; flowing a first portion of the heated feed water through an evaporator section of the HRSG and producing saturated steam at a production rate, the flow rate of the feed water through the economizer section being greater than required to sustain the production rate of steam in the evaporator section; flowing fuel for the turbine through a heat exchanger; and, flowing a second portion of the heated feed water provided by the economizer section through the heat exchanger then to an inlet of the economizer section, thereby heating the fuel flowing through the heat exchanger.

Pavel, J.; Meyers, G.A.; Baldwin, T.S.

1990-06-12T23:59:59.000Z

287

Combined cycle electric power plant and heat recovery steam generator having improved multi-loop temperature control of the steam generated  

SciTech Connect

A combined cycle electric power plant is described that includes gas and steam turbines and a steam generator for recovering the heat in the exhaust gases exited from the gas turbine and for using the recovered heat to produce and supply steam to the steam turbine. The steam generator includes a superheater tube and a steam drum from which heated steam is directed through the superheater to be additionally heated into superheated steam by the exhaust gas turbine gases. An afterburner serves to further heat the exhaust gas turbine gases passed to the superheater tube and a bypass conduit is disposed about the superheater tube whereby a variable steam flow determined by a bypass valve disposed in the bypass conduit may be directed about the superheater tube to be mixed with the superheated steam therefrom, whereby the temperature of the superheated steam supplied to the steam turbine may be accurately controlled. Steam temperature control means includes a first control loop responsive to the superheated steam temperature for regulating the position of the bypass valve with respect to a first setpoint, and a second control loop responsive to the superheated steam temperature for controlling the fuel supply to the afterburner with respect to a second setpoint varying in accordance with the bypass valve position. In particular, as the bypass valve position increases, the second setpoint, originally higher, is lowered toward a value substantially equal to that of the first setpoint.

Martz, L.F.; Plotnick, R.J.

1976-08-17T23:59:59.000Z

288

Milestone Report #2: Direct Evaporator Leak and Flammability Analysis Modifications and Optimization of the Organic Rankine Cycle to Improve the Recovery of Waste Heat  

Science Conference Proceedings (OSTI)

The direct evaporator is a simplified heat exchange system for an Organic Rankine Cycle (ORC) that generates electricity from a gas turbine exhaust stream. Typically, the heat of the exhaust stream is transferred indirectly to the ORC by means of an intermediate thermal oil loop. In this project, the goal is to design a direct evaporator where the working fluid is evaporated in the exhaust gas heat exchanger. By eliminating one of the heat exchangers and the intermediate oil loop, the overall ORC system cost can be reduced by approximately 15%. However, placing a heat exchanger operating with a flammable hydrocarbon working fluid directly in the hot exhaust gas stream presents potential safety risks. The purpose of the analyses presented in this report is to assess the flammability of the selected working fluid in the hot exhaust gas stream stemming from a potential leak in the evaporator. Ignition delay time for cyclopentane at temperatures and pressure corresponding to direct evaporator operation was obtained for several equivalence ratios. Results of a computational fluid dynamic analysis of a pinhole leak scenario are given.

Donna Post Guillen

2013-09-01T23:59:59.000Z

289

Recovery Act  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3 3 Recovery Act Buy American Requirements for Information Needed from Financial Assistance Applicants/Recipients for Waiver Requests Based on Unreasonable Cost or Nonavailability Applicants for and recipients of financial assistance funded by the Recovery Act must comply with the requirement that all of the iron, steel, and manufactured goods used for a project for the construction, alteration, maintenance, or repair of a public building or public work be produced in the United States, unless the head of the agency makes a waiver, or determination of inapplicability of the Buy American Recovery Act provisions, based on one of the authorized exceptions. The authorized exceptions are unreasonable cost, nonavailability, and in furtherance of the public interest. This

290

Energy recovery system  

DOE Patents (OSTI)

The present invention is directed to an improved wet air oxidation system and method for reducing the chemical oxygen demand (COD) of waste water used from scrubbers of coal gasification plants, with this COD reduction being sufficient to effectively eliminate waste water as an environmental pollutant. The improvement of the present invention is provided by heating the air used in the oxidation process to a temperature substantially equal to the temperature in the oxidation reactor before compressing or pressurizing the air. The compression of the already hot air further heats the air which is then passed in heat exchange with gaseous products of the oxidation reaction for "superheating" the gaseous products prior to the use thereof in turbines as the driving fluid. The superheating of the gaseous products significantly minimizes condensation of gaseous products in the turbine so as to provide a substantially greater recovery of mechanical energy from the process than heretofore achieved.

Moore, Albert S. (Morgantown, WV); Verhoff, Francis H. (Morgantown, WV)

1980-01-01T23:59:59.000Z

291

Energy recovery solves hospital's problem  

SciTech Connect

A heat recovery system for a hospital heating-ventilation-air conditioning installation is described. The system design allows for recovery of energy in the laundry exhaust air, distribution of supply air to the patient care wing, easy access for servicing, and economic feasibility. A rotary energy recovery wheel was selected as the energy recovery device because of its performance and economical advantages. The unit work continuously without difficulty during the severe winter of 1976. (PMA)

1977-08-01T23:59:59.000Z

292

A corrosive resistant heat exchanger  

DOE Patents (OSTI)

A corrosive and erosive resistant heat exchanger which recovers heat from a contaminated heat stream. The heat exchanger utilizes a boundary layer of innocuous gas, which is continuously replenished, to protect the heat exchanger surface from the hot contaminated gas. The innocuous gas is pumped through ducts or perforations in the heat exchanger wall. Heat from the heat stream is transferred by radiation to the heat exchanger wall. Heat is removed from the outer heat exchanger wall by a heat recovery medium. 3 figs., 3 tabs.

Richlen, S.L.

1987-08-10T23:59:59.000Z

293

White Paper for U.S. Army Rapid Equipping Force: Waste Heat Recovery with Thermoelectric and Lithium-Ion Hybrid Power System  

DOE Green Energy (OSTI)

By harvesting waste heat from engine exhaust and storing it in light-weight high-capacity modules, it is believed that the need for energy transport by convoys can be lowered significantly. By storing this power during operation, substantial electrical power can be provided during long periods of silent operation, while the engines are not operating. It is proposed to investigate the potential of installing efficient thermoelectric generators on the exhaust systems of trucks and other vehicles to generate electrical power from the waste heat contained in the exhaust and to store that power in advanced power packs comprised of polymer-gel lithium ion batteries. Efficient inexpensive methods for production of the thermoelectric generator are also proposed. The technology that exists at LLNL, as well as that which exists at industrial partners, all have high technology readiness level (TRL). Work is needed for integration and deployment.

Farmer, J C

2007-11-26T23:59:59.000Z

294

Cost-Effective Fabrication Routes for the Production of Quantum Well Structures and Recovery of Waste Heat from Heavy Duty Trucks  

Science Conference Proceedings (OSTI)

The primary objectives of Phase I were: (a) carry out cost, performance and system level models, (b) quantify the cost benefits of cathodic arc and heterogeneous nanocomposites over sputtered material, (c) evaluate the expected power output of the proposed thermoelectric materials and predict the efficiency and power output of an integrated TE module, (d) define market acceptance criteria by engaging Caterpillar's truck OEMs, potential customers and dealers and identify high-level criteria for a waste heat thermoelectric generator (TEG), (e) identify potential TEG concepts, and (f) establish cost/kWatt targets as well as a breakdown of subsystem component cost targets for the commercially viable TEG.

Willigan, Rhonda

2009-09-30T23:59:59.000Z

295

Geothermal: Sponsored by OSTI -- Recovery Act: Finite Volume...  

Office of Scientific and Technical Information (OSTI)

GEOTHERMAL TECHNOLOGIES LEGACY COLLECTION - Sponsored by OSTI -- Recovery Act: Finite Volume Based Computer Program for Ground Source Heat Pump Systems Geothermal Technologies...

296

Energy Recovery During Expansion of Compressed Gas Using Power...  

NLE Websites -- All DOE Office Websites (Extended Search)

Recovery During Expansion of Compressed Gas Using Power Plant Low-Quality Heat Sources Opportunity The Department of Energy's National Energy Technology Laboratory (NETL) is...

297

Integration of a "Passive Water Recovery" MEA into a Portable...  

NLE Websites -- All DOE Office Websites (Extended Search)

complexity and scaling difficulties of water recovery components such as the condenser heat exchanger. To overcome this barrier, the research objective of the University of...

298

Water Recovery From Humidified Power Cycles  

Science Conference Proceedings (OSTI)

Recovery of water from humidified cycles using a scrubber-desaturator, and the recovered water's clean-up and reuse have been shown to be practical, with comparatively low increases in capital costs and heat rates.

1998-02-09T23:59:59.000Z

299

Recovery Newsletters  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

newsletters Office of Environmental newsletters Office of Environmental Management 1000 Independence Ave., SW Washington, DC 20585 202-586-7709 en 2011 ARRA Newsletters http://energy.gov/em/downloads/2011-arra-newsletters 2011 ARRA Newsletters

300

High performance steam cogeneration (proof-of-concept phases). Phase 2, HRSG 500-hour test report: Final report  

SciTech Connect

Recent advances in small once-through Alloy 800 steam generators, improved materials technology, and application of small industrial gas turbine technology to steam turbine cogeneration offers the potential to make a step increase in steam temperature from around 1000{degree}F, where industry has been for almost fifty years, to 1500{degree}F. In small cogeneration systems, it is economically practical to introduce new technology and make a step change in temperature where it may not be possible (given the regulatory environment and economic risk) for a major change in steam temperature to be introduced in the hundreds of megawatt size of an electric utility. Increasing the peak steam temperature in a steam turbine cycle allows more work to be extracted or electrical power to be generated from a given quantity of heat input. Figure 1 plots steam efficiency as a function of superheat steam temperature and pressure for a turbine-back pressure of 166 psia. This figure clearly shows that increasing the steam conditions from the typical current practice of 900{degree}F and 900 psia to 1500{degree}F and 1500 psia will increase the steam cycle efficiency by 53%. The combination of higher cycle efficiency with an advanced high efficiency steam turbine design provides a substantial increase in turbine output power for a given steam flowrate. The output of this advanced high temperature steam turbine is approximately twice that of a current industrial practive turbine for the same turbine flowrate as seen in Figure 2.

Campbell, A.H.

1992-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "hrsg heat recovery" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Modern Heating Options for Commercial/Institutional Buildings  

NLE Websites -- All DOE Office Websites (Extended Search)

reducing the heating energy in buildings using a combination of low temperature boilers, heat recovery strategies and a new approach to geo-thermal systems. His data from...

302

Heat Exchangers Fouling and Corrosion-A Detailed Investigation  

Science Conference Proceedings (OSTI)

Presentation Title, Aluminum Smelter Waste Heat Recovery Plant (Heat Exchangers Fouling and Corrosion-A Detailed Investigation). Author(s), Hadi Fanisalek, ...

303

An Innovative Compact Heat Exchanger Solution for Aluminium Off ...  

Science Conference Proceedings (OSTI)

Presentation Title, An Innovative Compact Heat Exchanger Solution for Aluminium Off-Gas Cooling and Heat Recovery. Author(s), El Hani Bouhabila, Erling ...

304

ARM - Recovery Act Instruments  

NLE Websites -- All DOE Office Websites (Extended Search)

ActRecovery Act Instruments ActRecovery Act Instruments Recovery Act Logo Subscribe FAQs Recovery Act Instruments Recovery Act Fact Sheet March 2010 Poster (PDF, 10MB) External Resources Recovery Act - Federal Recovery Act - DOE Recovery Act - ANL Recovery Act - BNL Recovery Act - LANL Recovery Act - PNNL Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Recovery Act Instruments These pages provide a breakdown of the new instruments planned for installation among the permanent and mobile ARM sites. In addition, several instruments will be purchased for use throughout the facility and deployed as needed. These are considered "facility spares" and are included in the table below. View All | Hide All ARM Aerial Facility Instrument Title Instrument Mentor Measurement Group Measurements

305

Screen payback on cogeneration-system options  

SciTech Connect

Presented here are charts that provide a quick look at the relationship among the primary variables that affect the viability of a cogeneration project. The graphs are not intended to be complete feasibility studies, but rather screening aids for understanding the important interrelationships. Use of the charts will enable engineers to compare the predominant system options: gas turbine with heat-recovery steam generator (HRSG), diesel engine with HRSG, and fired boiler with steam turbine. The three options are presented separately because of differing capital costs and heat balances.

Wilson, F.

1984-06-01T23:59:59.000Z

306

Recovery Act | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

March 15, 2010 March 15, 2010 A woodchip-fired combined heat and power system will be built in Montpelier, Vt. | File photo Jobs, sustainable heating coming to Vermont city Their new woodchip-fired combined heat and power system will heat the Capitol Complex, the city's schools, City Hall and as many as 156 other buildings in the downtown area. March 12, 2010 Reginald Speight, CEO of Martin County Community Action | Photo courtesy of Martin County Community Action N.C. Agency Growing, Helping Citizens Save Money MCCA runs a hybrid program in the state that has expanded energy efficiency services to municipalities and made advanced-income households eligible for weatherization, and this work helped prepare the agency for the workload it is seeing now under the Recovery Act.

307

Recovery Act Open House  

NLE Websites -- All DOE Office Websites (Extended Search)

Recovery Act Open House North Wind Environmental was one of three local small businesses that received Recovery Funding for projects at DOE's Idaho Site. Members of the community...

308

Sonja Deppisch (Hrsg.) Transdisziplinre Impulse  

E-Print Network (OSTI)

Jahresverlauf hervorra- gend - aufgrund von regeltechnischen Pro- blemen werden aber zunehmend Wind- kraftwerke Wind- kraftwerke abgeschaltet. Wertvolle Energie wird so nicht genutzt. Gefördert vom Bund und Land- schaftlichen Geräte (Beispiel: Kosten für ein studentenmikroskop ca. 1000 eur), konnten durch dieses re-Investitions

von Storch, Hans

309

Overview of Electricity Markets A good overview is contained in [1].  

E-Print Network (OSTI)

accepted that electric energy generation, transmission, and distribution required either public transmission or distribution system than two parallel ones) [3]. This view was first called into question between the combustion turbines (CTs) and the heat recovery steam generators (HRSG) that are driven

McCalley, James D.

310

Proceedings: Sixth International Conference on Fossil Plant Cycle Chemistry  

Science Conference Proceedings (OSTI)

The purity of boiler water, feedwater, and steam is central to ensuring component availability and reliability in fossil-fired plants. These conference proceedings address the state of the art in fossil plant and combined cycle/heat recovery steam generator (HRSG) cycle chemistry as well as international practices for control of corrosion and water preparation and purification.

None

2001-04-01T23:59:59.000Z

311

Steam driven markets  

Science Conference Proceedings (OSTI)

The market for steam equipment has been relatively level. Looking ahead, manufacturers anticipate steady market growth worldwide. Steam equipment manufacturers share a similar view of the market for next few years - upward. The steady upward climb is being attributed to a number of factors that will benefit steam turbine and heat recovery steam generator (HRSG) makers.

Anderson, J.L.

1993-02-01T23:59:59.000Z

312

Proceedings: Sixth International Conference on Fossil Plant Cycle Chemistry  

Science Conference Proceedings (OSTI)

The purity of boiler water, feedwater, and steam is central to ensuring component availability and reliability in fossil-fired plants. These conference proceedings address the state of the art in fossil plant and combined cycle/heat recovery steam generator (HRSG) cycle chemistry as well as international practices for control of corrosion and water preparation and purification.

2001-03-30T23:59:59.000Z

313

Combined Heat and Power Plant Steam Turbine  

E-Print Network (OSTI)

waste heat) Gas Turbine University Substation High Pressure Natural Gas Campus Electric Load SouthernCombined Heat and Power Plant Steam Turbine Steam Turbine Chiller Campus Heat Load Steam (recovered Generator Heat Recovery Alternative Uses: 1. Campus heating load 2. Steam turbine chiller to campus cooling

Rose, Michael R.

314

Drain Water Heat Recovery | Department of Energy  

NLE Websites -- All DOE Office Websites (Extended Search)

to shower, wash dishes, or wash clothing) to preheat cold water entering the water heater or going to other water fixtures. This reduces the amount of energy needed for water...

315

Heat and Seed Recovery Technology Project  

DOE Green Energy (OSTI)

The objective of this work is to address technical issues related to both the MHD topping and bottoming cycles and to their integration. Design information will be obtained through modeling and experimentation. This information, together with the insults of long duration testing at DOE`s Coal Fired Flow Facility (CFFF) and Component Development and Integration Facility (CDIF), can be used to reliably design the first-generation MHD retrofit plant. Work during the reporting period focused on the following tasks: (1) computer modeling of the integrated topping-cycle power train (combustor/nozzle/channel/diffuser); (2) evaluation of materials for the bottoming steam cycle; (3) systems analysis of an MHD/CO{sub 2} cyde; and (4) the completion of a topical report on the reactivation of the ANL superconducting magnet system. Accomplishments in these areas are described briefly.

Swift, W.M.; Petrick, M.; Natesan, K.

1993-03-01T23:59:59.000Z

316

Heat and Seed Recovery Technology Project  

DOE Green Energy (OSTI)

The objective of this work is to address technical issues related to both the MHD topping and bottoming cycles and to their integration. Design information will be obtained through modeling and experimentation. This information, together with the insults of long duration testing at DOE's Coal Fired Flow Facility (CFFF) and Component Development and Integration Facility (CDIF), can be used to reliably design the first-generation MHD retrofit plant. Work during the reporting period focused on the following tasks: (1) computer modeling of the integrated topping-cycle power train (combustor/nozzle/channel/diffuser); (2) evaluation of materials for the bottoming steam cycle; (3) systems analysis of an MHD/CO[sub 2] cyde; and (4) the completion of a topical report on the reactivation of the ANL superconducting magnet system. Accomplishments in these areas are described briefly.

Swift, W.M.; Petrick, M.; Natesan, K.

1993-01-01T23:59:59.000Z

317

Distributed Generation with Heat Recovery and Storage  

E-Print Network (OSTI)

electricity and natural gas usage. Cooling electricity loadspurchases of natural gas for direct end usage. Hence, unlikeof natural gas purchased for direct end usage. As a result,

Siddiqui, Afzal; Marnay, Chris; Firestone, Ryan M.; Zhou, Nan

2005-01-01T23:59:59.000Z

318

Distributed Generation with Heat Recovery and Storage  

E-Print Network (OSTI)

electricity and natural gas usage. Cooling electricity loadspurchases of natural gas for direct end usage. Hence, unlikeof natural gas purchased for direct end usage. As a result,

Siddiqui, Afzal S.; Marnay, Chris; Firestone, Ryan M.; Zhou, Nan

2008-01-01T23:59:59.000Z

319

Distributed Generation with Heat Recovery and Storage  

E-Print Network (OSTI)

On-site thermal power generation is typically less efficienthighly centralised power generation and delivery systemProduction from US Power Generation Note this is only the

Siddiqui, Afzal; Marnay, Chris; Firestone, Ryan M.; Zhou, Nan

2005-01-01T23:59:59.000Z

320

Distributed Generation with Heat Recovery and Storage  

E-Print Network (OSTI)

Given the site’s energy loads, utility tariff structure, andgas tariffs, which reflect the current state of energy coststariff. Natural Gas Natural gas rates for San Francisco are obtained from the Annual Energy

Siddiqui, Afzal S.; Marnay, Chris; Firestone, Ryan M.; Zhou, Nan

2008-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "hrsg heat recovery" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Distributed Generation with Heat Recovery and Storage  

E-Print Network (OSTI)

Electric (PG&E); the electricity tariff for San Franciscocomponents of the electricity tariff are volumetric, demand,5. PG&E Electricity and Power Tariff summer* Volumetric ($/

Siddiqui, Afzal; Marnay, Chris; Firestone, Ryan M.; Zhou, Nan

2005-01-01T23:59:59.000Z

322

Distributed Generation with Heat Recovery and Storage  

E-Print Network (OSTI)

Electric (PG&E); the electricity tariff for San Franciscocomponents of the electricity tariff are volumetric, demand,5. PG&E Electricity and Power Tariff summer* Volumetric ($/

Siddiqui, Afzal S.; Marnay, Chris; Firestone, Ryan M.; Zhou, Nan

2008-01-01T23:59:59.000Z

323

Waste Heat Recovery - Programmaster.org  

Science Conference Proceedings (OSTI)

Mar 15, 2012 ... Effect of Materials on the Autoignition of Cyclopentane: Donna Guillen1; 1Idaho National Laboratory Cyclopentane, a flammable hydrocarbon, ...

324

Distributed Generation with Heat Recovery and Storage  

E-Print Network (OSTI)

Electricity generated by distributed energy resources (DER)Energy, Office of Distributed Energy of the US Department ofdefined names including distributed energy resources (DER),

Siddiqui, Afzal; Marnay, Chris; Firestone, Ryan M.; Zhou, Nan

2005-01-01T23:59:59.000Z

325

Distributed Generation with Heat Recovery and Storage  

E-Print Network (OSTI)

of customer adoption of distributed energy resources, LBNLR. M. (2005). Distributed energy resources customer adoptionT. (2003). Gas-fired distributed energy resource technology

Siddiqui, Afzal S.; Marnay, Chris; Firestone, Ryan M.; Zhou, Nan

2008-01-01T23:59:59.000Z

326

Distributed Generation with Heat Recovery and Storage  

E-Print Network (OSTI)

fired natural gas absorption chiller (kW) Turnkey cost offired natural gas absorption chiller (US$) Annualized costfired natural gas absorption chiller (US$), where DCCap

Siddiqui, Afzal S.; Marnay, Chris; Firestone, Ryan M.; Zhou, Nan

2008-01-01T23:59:59.000Z

327

CFD Simulation of Infiltration Heat Recovery  

E-Print Network (OSTI)

in the outer sheathing (plywood) allow air to leak into thefor turbulence. The plywood sheathing is represented as an

Buchanan, C.R.

2011-01-01T23:59:59.000Z

328

Miniaturized stirling engines for waste heat recovery.  

E-Print Network (OSTI)

??Portable electronic devices have made a profound impact on our society and economy due to their widespread use for computation, communications, and entertainment. The performance… (more)

Lemaire, Lacey-Lynne

2012-01-01T23:59:59.000Z

329

Distributed Generation with Heat Recovery and Storage  

E-Print Network (OSTI)

involved, supplemental absorption cooling allows downsizingdisplaced by absorption cooling. The same principle appliesof storage and absorption cooling in case of the cooling

Siddiqui, Afzal; Marnay, Chris; Firestone, Ryan M.; Zhou, Nan

2005-01-01T23:59:59.000Z

330

Distributed Generation with Heat Recovery and Storage  

E-Print Network (OSTI)

a microgrid,” Journal of Energy Engineering, 131(1), 2-25.be published in the Journal of Energy Engineering. The work

Siddiqui, Afzal S.; Marnay, Chris; Firestone, Ryan M.; Zhou, Nan

2008-01-01T23:59:59.000Z

331

CFD Simulation of Infiltration Heat Recovery  

E-Print Network (OSTI)

residential buildings with dynamic insulation”, 16* AIVCas dynamic insulation, air is drawn through the building

Buchanan, C.R.

2011-01-01T23:59:59.000Z

332

Combined Cycle Performance Monitoring and Recovery Guideline  

Science Conference Proceedings (OSTI)

The benefits of improved combined cycle power plant performance continue to grow as the cost of fuel rises and international concerns over global warming increase.This guideline provides a framework for performance monitoring, assessment, recovery and optimization of combined cycle power plants. The guideline distills existing experience and documents on heat rate recovery and capacity improvement into a comprehensive manual for plant implementation and training applications. The purpose ...

2012-12-31T23:59:59.000Z

333

Recovery Act | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

19, 2010 19, 2010 The Blaine County Public Safety Facility houses between 60 and 80 prisoners and roughly 30 staffers. | Photo courtesy of Blaine High Water Heating Bills on Lockdown at Idaho Jail Using funds from the American Recovery and Reinvestment Act, the county is installing a solar thermal hot water system that will provide nearly 70 percent of the power required for heating 600,000 gallons of water for the jail annually. August 16, 2010 800,000 Jobs by 2012 President Barack Obama visited ZBB Energy Corporation in Wisconsin and declared that our commitment to clean energy is expected to lead to more than 800,000 jobs by 2012. August 16, 2010 An array of solar collectors | Photo courtesy of Trane Knox County Detention Facility Goes Solar for Heating Water Hot water demand soars at the six-building Knox County Detention Facility

334

Case study: savings from energy recovery  

SciTech Connect

The design, operation, and performance of a heat-pipe heat exchanger installed in a commercial laundry dryer system are described. Hot air from the dryer exhaust is passed through one side of the exchanger and cold makeup air is passed through the other side in a counter flow arrangement. Energy from the hot air is transferred by heat pipes to the other side of the exchanger, thereby warming the incoming air. An annual savings of approximately $2000 due to decreased natural gas consumption by the dryer has been realized with use of this heat recovery unit. (LCL)

1976-11-01T23:59:59.000Z

335

A2: Corrosion Problems in Heat Recovery for Water Heating  

Science Conference Proceedings (OSTI)

A30: Study on Super Stable All-solid-state Battery at High Temperature · A3: Investigation on Co-combustion Kinetics of Anthracite Coal and Biomass Char by  ...

336

Recovery mechanisms of Arctic summer sea ice  

E-Print Network (OSTI)

[1] We examine the recovery of Arctic sea ice from prescribed ice?free summer conditions in simulations of 21st century climate in an atmosphere–ocean general circulation model. We find that ice extent recovers typically within two years. The excess oceanic heat that had built up during the ice?free summer is rapidly returned to the atmosphere during the following autumn and winter, and then leaves the Arctic partly through increased longwave emission at the top of the atmosphere and partly through reduced atmospheric heat advection from lower latitudes. Oceanic heat transport does not contribute significantly to the loss of the excess heat. Our results suggest that anomalous loss of Arctic sea ice during asinglesummerisreversible,astheice–albedo feedback is alleviated by large?scale recovery mechanisms. Hence, hysteretic threshold behavior (or a “tipping point”) is unlikely to occur during the decline of Arctic summer sea?

unknown authors

2011-01-01T23:59:59.000Z

337

Energy Recovery in Industrial Distillation Processes  

E-Print Network (OSTI)

Distillation processes are energy intensive separation processes which present attractive opportunities for energy conservation. Through the use of multistage vapor recompression, heat which is normally unavailable can be delivered at suitably high temperatures resulting in significant energy savings. The distillation process will be reviewed as it relates to both vapor recompression and heat pumping techniques and case study examples of these energy recovery methods will be discussed.

Paul, D. B.

1983-01-01T23:59:59.000Z

338

Modified Accelerated Cost-Recovery System (MACRS) + Bonus Depreciation  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Modified Accelerated Cost-Recovery System (MACRS) + Bonus Modified Accelerated Cost-Recovery System (MACRS) + Bonus Depreciation (2008-2012) Modified Accelerated Cost-Recovery System (MACRS) + Bonus Depreciation (2008-2012) < Back Eligibility Agricultural Commercial Industrial Savings Category Bioenergy Commercial Heating & Cooling Manufacturing Buying & Making Electricity Alternative Fuel Vehicles Hydrogen & Fuel Cells Wind Water Solar Heating & Cooling Heating Water Heating Program Info Start Date 1986 Program Type Corporate Depreciation Provider U.S. Internal Revenue Service Under the federal Modified Accelerated Cost-Recovery System (MACRS), businesses may recover investments in certain property through depreciation deductions. The MACRS establishes a set of class lives for various types of property, ranging from three to 50 years, over which the property may be

339

Categorical Exclusion Determinations: American Recovery and Reinvestment  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Categorical Exclusion Determinations: American Recovery and Categorical Exclusion Determinations: American Recovery and Reinvestment Act Related Categorical Exclusion Determinations: American Recovery and Reinvestment Act Related Categorical Exclusion Determinations issued for actions related to the the American Recovery and Reinvestment Act of 2009. DOCUMENTS AVAILABLE FOR DOWNLOAD January 19, 2011 CX-005047: Categorical Exclusion Determination Chicago Area Alternative Fuels Deployment Project CX(s) Applied: B5.1 Date: 01/19/2011 Location(s): Chicago, Illinois Office(s): Energy Efficiency and Renewable Energy, National Energy Technology Laboratory January 19, 2011 CX-005039: Categorical Exclusion Determination Development and Validation of a Gas-Fired Residential Heat Pump Water Heater CX(s) Applied: B3.6 Date: 01/19/2011

340

American Recovery and Reinvestment Act Information Services  

NLE Websites -- All DOE Office Websites (Extended Search)

Recovery and Reinvestment Act Recovery and Reinvestment Act Information Services American Recovery and Reinvestment Act American Recovery and Reinvestment Act Information Services American Recovery and Reinvestment Act American Recovery and Reinvestment Act Information Services American Recovery and Reinvestment Act American Recovery and Reinvestment Act American Recovery and Reinvestment Act American Recovery and Reinvestment Act American Recovery and Reinvestment Act American Recovery and Reinvestment Act American Recovery and Reinvestment Act American Recovery and Reinvestment Act American Recovery and Reinvestment Act American Recovery and Reinvestment Act American Recovery and Reinvestment Act American Recovery and Reinvestment Act American Recovery and Reinvestment Act American Recovery and Reinvestment Act

Note: This page contains sample records for the topic "hrsg heat recovery" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Optimal selection of on-site generation with combined heat and power applications  

E-Print Network (OSTI)

ios in which distributed generation and heat recovery486-7976 Keywords: distributed generation; combined heat andCERTS) Microgrid. Distributed generation would alleviate the

Siddiqui, Afzal S.; Marnay, Chris; Bailey, Owen; Hamachi LaCommare, Kristina

2004-01-01T23:59:59.000Z

342

Recovery Act | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

July 18, 2011 July 18, 2011 Secretary Chu speaks at the A123 Systems lithium-ion battery manufacturing plant in Romulus, Michigan, while employees look on. | Photo Courtesy of Damien LaVera, Energy Department Secretary Chu Visits Advanced Battery Plant in Michigan, Announces New Army Partnership Thirty new manufacturing plants across the country for electric vehicle batteries and components - including A123 in Michigan - were supported through the Recovery Act, meaning we'll have the capacity to manufacture enough batteries and components for 500,000 electric vehicles annually by 2015. July 26, 2011 Smart Meters Helping Oklahoma Consumers Save Hundreds During Summer Heat With already 32 days reaching over 100 degrees this summer, Oklahoma is certainly feeling the heat. But smart meters -- just one of the advanced

343

Optimization of Heat Exchanger Cleaning  

E-Print Network (OSTI)

The performance of heat integration systems is quantified in terms of the amount of heat that is recovered. This decreases with time due to increased fouling of the heat exchange surface. Using the "Total Fouling Related Expenses (TFRE)" approach, economic incentives for heat exchanger cleaning are evaluated using linear, exponential, and exponential finite decrease models of the heat recovery decay. A mathematical comparison of mechanical and chemical cleaning of heat exchangers has identified the most significant parameters which affect the choice between the two methods.

Siegell, J. H.

1986-06-01T23:59:59.000Z

344

High efficiency shale oil recovery  

SciTech Connect

The overall project objective is to demonstrate the high efficiency of the Adams Counter-Current shale oil recovery process. The efficiency will first be demonstrated on a small scale, in the current phase, after which the demonstration will be extended to the operation of a small pilot plant. Thus the immediate project objective is to obtain data on oil shale retorting operations in a small batch rotary kiln that will be representative of operations in the proposed continuous process pilot plant. Although an oil shale batch sample is sealed in the batch kiln from the start until the end of the run, the process conditions for the batch are the same as the conditions that an element of oil shale would encounter in a continuous process kiln. Similar chemical and physical conditions (heating, mixing, pyrolysis, oxidation) exist in both systems.The two most important data objectives in this phase of the project are to demonstrate (1) that the heat recovery projected for this project is reasonable and (2) that an oil shale kiln will run well and not plug up due to sticking and agglomeration. The following was completed this quarter. (1) Twelve pyrolysis runs were made on five different oil shales. All of the runs exhibited a complete absence of any plugging, tendency. Heat transfer for Green River oil shale in the rotary kiln was 84.6 Btu/hr/ft[sup 2]/[degrees]F, and this will provide for ample heat exchange in the Adams kiln. (2) One retorted residue sample was oxidized at 1000[degrees]F. Preliminary indications are that the ash of this run appears to have been completely oxidized. (3) Further minor equipment repairs and improvements were required during the course of the several runs.

Adams, D.C.

1993-04-22T23:59:59.000Z

345

Heat pipe dynamics. Final report, April 30, 1981. [Uses of heat pipe, especially in solar collector  

DOE Green Energy (OSTI)

A heat-pipe flat plate solar collector is constructed like a typical flat plate collector with the exception that individual heat pipes are attached to the collector surface to transfer collected heat via a phase change from collector surface into an attached jacket containing a phase change material. The efficiency of such a collector was measured roughly. Also briefly described are: a heat-pipe heat exchanger, heat-pipe heat exchanger freeze proofing, heat-pipe attic ventilation, transfer of light bulb heat via a heat pipe to heat water, heat recovery via heat pipe, cooling of oil in engines and transmissions via heat pipe, a tracking reflector, automatic sun tracker, single-stroke vacuum pump for heat-pipe manufacture, and heat pipe heat transfer from rock bed. (LEW)

Norman, R.M. Sr.

1981-01-01T23:59:59.000Z

346

Heat Pipe Technology for Energy Conservation in the Process Industry  

E-Print Network (OSTI)

Many applications for heat pipe technology have emerged in the relatively short time this technology has been known. Heat pipes incorporated in heat exchangers have been used in tens of thousands of successful heat recovery systems. These systems range from residential and commercial air-to-air heat exchangers to giant air preheaters for the process and utility industries. The heat pipe offers a unique, efficient heat transfer device that can recover valuable thermal energy resulting in reduced equipment and operating costs. Q-dot is the world leader in heat pipe technology and we have applied our expertise in engineering heat recovery products for the process industry. This paper discusses two such products, the heat pipe air preheater and waste heat recovery boiler. These heat pipe products have been used in many successful installations all over the world and some important, distinctive features of these systems will be presented.

Price, B. L. Jr.

1985-05-01T23:59:59.000Z

347

Tenth oil recovery conference  

SciTech Connect

The Tertiary Oil Recovery Project is sponsored by the State of Kansas to introduce Kansas producers to the economic potential of enhanced recovery methods for Kansas fields. Specific objectives include estimation of the state-wide tertiary oil resource, identification and evaluation of the most applicable processes, dissemination of technical information to producers, occasional collaboration on recovery projects, laboratory studies on Kansas applicable processes, and training of students and operators in tertiary oil recovery methods. Papers have been processed separately for inclusion on the data base.

Sleeper, R. (ed.)

1993-01-01T23:59:59.000Z

348

Heat pipe array heat exchanger  

DOE Patents (OSTI)

A heat pipe arrangement for exchanging heat between two different temperature fluids. The heat pipe arrangement is in a ounterflow relationship to increase the efficiency of the coupling of the heat from a heat source to a heat sink.

Reimann, Robert C. (Lafayette, NY)

1987-08-25T23:59:59.000Z

349

Recovery Act State Summaries | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Recovery Act State Summaries Recovery Act State Summaries Recovery Act State Summaries Alabama Recovery Act State Memo Alaska Recovery Act State Memo American Samoa Recovery Act State Memo Arizona Recovery Act State Memo Arkansas Recovery Act State Memo California Recovery Act State Memo Colorado Recovery Act State Memo Connecticut Recovery Act State Memo Delaware Recovery Act State Memo District of Columbia Recovery Act State Memo Florida Recovery Act State Memo Georgia Recovery Act State Memo Guam Recovery Act State Memo Hawaii Recovery Act State Memo Idaho Recovery Act State Memo Illinois Recovery Act State Memo Indiana Recovery Act State Memo Iowa Recovery Act State Memo Kansas Recovery Act State Memo Kentucky Recovery Act State Memo Louisiana Recovery Act State Memo Maine Recovery Act State Memo

350

High efficiency shale oil recovery  

SciTech Connect

The overall project objective is to demonstrate the high efficiency of the Adams Counter-Current shale oil recovery process. The efficiency will first be demonstrated on a small scale, in the current phase, after which the demonstration will be extended to the operation of a small pilot plant. Thus the immediate project objective is to obtain data on oil shale retorting operations in a small batch rotary kiln that will be representative of operations in the proposed continuous process pilot plant. Although an oil shale batch sample is sealed in the batch kiln from the start until the end of the run, the process conditions for the batch are the same as the conditions that an element of oil shale would encounter in a continuous process kiln. Similar chemical and physical (heating, mixing) conditions exist in both systems. The two most important data objectives in this phase of the project are to demonstrate (1) that the heat recovery projected for this project is reasonable and (2) that an oil shale kiln will run well and not plug up due to sticking and agglomeration. The following was completed and is reported on this quarter: (1) A software routine was written to eliminate intermittently inaccurate temperature readings. (2) We completed the quartz sand calibration runs, resolving calibration questions from the 3rd quarter. (3) We also made low temperature retorting runs to identify the need for certain kiln modifications and kiln modifications were completed. (4) Heat Conductance data on two Pyrolysis runs were completed on two samples of Occidental oil shale.

Adams, D.C.

1992-01-01T23:59:59.000Z

351

Low Grade Waste Heat Driven Desalination and SO2 Scrubbing  

Science Conference Proceedings (OSTI)

About 15% of the electricity required to produce aluminum is lost as waste heat ... An Overview of Energy Consumption and Waste Generation in the Recovery of ...

352

Oakland University Human Health Science Building Geothermal Heat...  

Open Energy Info (EERE)

Last modified on July 22, 2011. Project Title Oakland University Human Health Science Building Geothermal Heat Pump Systems Project Type Topic 1 Recovery Act - Geothermal...

353

Waste Heat Utilization to Increase Energy Efficiency in the Metals ...  

Science Conference Proceedings (OSTI)

This system will produce electricity, and/or process steam. • Low grade: ... or Save Conflict]. Waste Heat Reduction and Recovery Options for Metals Industry.

354

Flexibility and economics of combustion turbine-based cogeneration systems  

SciTech Connect

The major objective of this paper is to discuss various options that affect the efficiency of combustion turbine cogeneration plants and the commensurate net worth impact to the firm. Topics considered include technical evaluation parameters, an efficiency definition, a cogeneration heat rate definition, the qualitative value of efficiency and the cogeneration heat rate, economic evaluation techniques, industrial processes suitable for cogeneration, equipment requirements, the combustion turbine package, the heat recovery steam generator package, balance of plant equipment, engineering and construction, the total cost of incorporating the cogeneration plant, cogeneration with the basic combustion turbine/heat recovery steam generator (CT/HRSG) cycle, cogeneration-steam production increase by ductburning, dual-pressure HRSG, the backpressure steam turbine, supercharging, separating electrical power generation from steam demand, and incorporating a backup source of steam generation.

Wohlschlegel, M.V.; Marcellino, A.; Myers, G.

1983-01-01T23:59:59.000Z

355

Building Technologies Office: Recovery Act-Funded Working Fluid Projects  

NLE Websites -- All DOE Office Websites (Extended Search)

Working Fluid Projects to someone by E-mail Working Fluid Projects to someone by E-mail Share Building Technologies Office: Recovery Act-Funded Working Fluid Projects on Facebook Tweet about Building Technologies Office: Recovery Act-Funded Working Fluid Projects on Twitter Bookmark Building Technologies Office: Recovery Act-Funded Working Fluid Projects on Google Bookmark Building Technologies Office: Recovery Act-Funded Working Fluid Projects on Delicious Rank Building Technologies Office: Recovery Act-Funded Working Fluid Projects on Digg Find More places to share Building Technologies Office: Recovery Act-Funded Working Fluid Projects on AddThis.com... About Take Action to Save Energy Partner with DOE Activities Appliances Research Building Envelope Research Windows, Skylights, & Doors Research Space Heating & Cooling Research

356

Building Technologies Office: Recovery Act-Funded HVAC Research Projects  

NLE Websites -- All DOE Office Websites (Extended Search)

HVAC Research Projects to someone by E-mail HVAC Research Projects to someone by E-mail Share Building Technologies Office: Recovery Act-Funded HVAC Research Projects on Facebook Tweet about Building Technologies Office: Recovery Act-Funded HVAC Research Projects on Twitter Bookmark Building Technologies Office: Recovery Act-Funded HVAC Research Projects on Google Bookmark Building Technologies Office: Recovery Act-Funded HVAC Research Projects on Delicious Rank Building Technologies Office: Recovery Act-Funded HVAC Research Projects on Digg Find More places to share Building Technologies Office: Recovery Act-Funded HVAC Research Projects on AddThis.com... About Take Action to Save Energy Partner with DOE Activities Appliances Research Building Envelope Research Windows, Skylights, & Doors Research Space Heating & Cooling Research

357

Recovery Act Recipient Reporting  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Smart Grid Investment Grant Recipients Smart Grid Investment Grant Recipients November 19, 2009 1 Outline of Presentation * OMB Reporting Requirements * Jobs Guidance * FR.gov 2 Section 1512 of American Reinvestment and Recovery Act Outlines Recipient Reporting Requirements "Recipient reports required by Section 1512 of the Recovery Act will answer important questions, such as: â–Ş Who is receiving Recovery Act dollars and in what amounts? â–Ş What projects or activities are being funded with Recovery Act dollars? â–Ş What is the completion status of such projects or activities and what impact have they had on job creation and retention?" "When published on www.Recovery.gov, these reports will provide the public with an unprecedented level of transparency into how Federal dollars are being spent and will help drive accountability for the timely,

358

Summary - Caustic Recovery Technology  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Caustic Recovery Technology Caustic Recovery Technology ETR Report Date: July 2007 ETR-7 United States Department of Energy Office of Environmental Management (DOE-EM) External Technical Review of Caustic Recovery Technology Why DOE-EM Did This Review The Department of Energy (DOE) Environmental Management Office (EM-21) has been developing caustic recovery technology for application to the Hanford Waste Treatment Plant (WTP) to reduce the amount of Low Activity Waste (LAW) vitrified. Recycle of sodium hydroxide with an efficient caustic recovery process could reduce the amount of waste glass produced by greater than 30%. The Ceramatec Sodium (Na), Super fast Ionic CONductors (NaSICON) membrane has shown promise for directly producing 50% caustic with high sodium selectivity. The external review

359

Waste Heat Recapture from Supermarket Refrigeration Systems  

DOE Green Energy (OSTI)

The objective of this project was to determine the potential energy savings associated with improved utilization of waste heat from supermarket refrigeration systems. Existing and advanced strategies for waste heat recovery in supermarkets were analyzed, including options from advanced sources such as combined heat and power (CHP), micro-turbines and fuel cells.

Fricke, Brian A [ORNL

2011-11-01T23:59:59.000Z

360

Heat Transfer Enhancement: Second Generation Technology  

E-Print Network (OSTI)

This paper reviews current activity in the field of enhanced heat transfer, with the aim of illustrating the technology and typical applications. Guidelines for application of enhanced surfaces are given, and practical concerns and economics are discussed. Special attention is directed toward use of enhanced surfaces in industrial process heat exchangers and heat recovery equipment.

Bergles, A. E.; Webb, R. L.

1984-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "hrsg heat recovery" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

OE Recovery Act Archive | Department of Energy  

NLE Websites -- All DOE Office Websites (Extended Search)

Act » OE Recovery Act Archive Act » OE Recovery Act Archive OE Recovery Act Archive 2011 July 26, 2011: BLOG Smart Meters Helping Oklahoma Consumers Save Hundreds During Summer Heat Smart meters -- just one of the advanced technologies being used to modernize the grid -- are helping Oklahoma businesses and home owners beat high electricity bills not only during these summer months, but year-round. July 26, 2011: PRESS RELEASE CenterPoint Energy has released survey results from a 500 participant smart meter In-Home Display pilot program showing that 71 percent of customers changed their electricity consumption behavior as a result of the energy use data they accessed on their in-home displays. The results were released while U.S. Deputy Secretary of Energy Daniel B. Poneman visited Houston to

362

Categorical Exclusion Determinations: American Recovery and Reinvestment  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

9, 2010 9, 2010 CX-003355: Categorical Exclusion Determination Oklahoma State Energy Program American Recovery and Reinvestment Act- Phase 2 - Wind Turbine for Guthrie Waste Water Treatment Plant CX(s) Applied: B5.1 Date: 08/09/2010 Location(s): Guthrie, Oklahoma Office(s): Energy Efficiency and Renewable Energy, Golden Field Office August 9, 2010 CX-003354: Categorical Exclusion Determination Oklahoma State Energy Program American Recovery and Reinvestment Act - Heating, Ventilating, and Air Conditioning and Window Replacement in Administration Building CX(s) Applied: B5.1 Date: 08/09/2010 Location(s): Shawnee, Oklahoma Office(s): Energy Efficiency and Renewable Energy, Golden Field Office August 9, 2010 CX-003353: Categorical Exclusion Determination Oklahoma State Energy Program American Recovery and Reinvestment Act -

363

HEAVY AND THERMAL OIL RECOVERY PRODUCTION MECHANISMS  

SciTech Connect

The Stanford University Petroleum Research Institute (SUPRI-A) studies oil recovery mechanisms relevant to thermal and heavy-oil production. The scope of work is relevant across near-, mid-, and long-term time frames. In August of 2000 we received funding from the U. S. DOE under Award No. DE-FC26-00BC15311 that completed December 1, 2003. The project was cost shared with industry. Heavy oil (10 to 20{sup o} API) is an underutilized energy resource of tremendous potential. Heavy oils are much more viscous than conventional oils. As a result, they are difficult to produce with conventional recovery methods. Heating reduces oil viscosity dramatically. Hence, thermal recovery is especially important because adding heat, usually via steam injection generally improves displacement efficiency. The objectives of this work were to improve our understanding of the production mechanisms of heavy oil under both primary and enhanced modes of operation. The research described spanned a spectrum of topics related to heavy and thermal oil recovery and is categorized into: (1) multiphase flow and rock properties, (2) hot fluid injection, (3) improved primary heavy-oil recovery, (4) in-situ combustion, and (5) reservoir definition. Technology transfer efforts and industrial outreach were also important to project effort. The research tools and techniques used were quite varied. In the area of experiments, we developed a novel apparatus that improved imaging with X-ray computed tomography (CT) and high-pressure micromodels etched with realistic sandstone roughness and pore networks that improved visualization of oil-recovery mechanisms. The CT-compatible apparatus was invaluable for investigating primary heavy-oil production, multiphase flow in fractured and unfractured media, as well as imbibition. Imbibition and the flow of condensed steam are important parts of the thermal recovery process. The high-pressure micromodels were used to develop a conceptual and mechanistic picture of primary heavy-oil production by solution gas drive. They allowed for direct visualization of gas bubble formation, bubble growth, and oil displacement. Companion experiments in representative sands and sandstones were also conducted to understand the mechanisms of cold production. The evolution of in-situ gas and oil saturation was monitored with CT scanning and pressure drop data. These experiments highlighted the importance of depletion rate, overburden pressure, and oil-phase chemistry on the cold production process. From the information provided by the experiments, a conceptual and numerical model was formulated and validated for the heavy-oil solution gas drive recovery process. Also in the area of mechanisms, steamdrive for fractured, low permeability porous media was studied. Field tests have shown that heat injected in the form of steam is effective at unlocking oil from such reservoir media. The research reported here elucidated how the basic mechanisms differ from conventional steamdrive and how these differences are used to an advantage. Using simulations of single and multiple matrix blocks that account for details of heat transfer, capillarity, and fluid exchange between matrix and fracture, the importance of factors such as permeability contrast between matrix and fracture and oil composition were quantified. Experimentally, we examined the speed and extent to which steam injection alters the permeability and wettability of low permeability, siliceous rocks during thermal recovery. Rock dissolution tends to increase permeability moderately aiding in heat delivery, whereas downstream the cooled fluid deposits silica reducing permeability. Permeability reduction is not catastrophic. With respect to wettability, heat shifts rock wettability toward more water wet conditions. This effect is beneficial for the production of heavy and medium gravity oils as it improves displacement efficiency. A combination of analytical and numerical studies was used to examine the efficiency of reservoir heating using nonconventional wells such as horizontal and multi

Anthony R. Kovscek; Louis M. Castanier

2003-12-31T23:59:59.000Z

364

Enhanced recovery update  

SciTech Connect

Three key projects featuring enhanced operations in California are described. In the Kern River oil field, steaming at a pilot project is testing the hot plate heavy oil recovery method. In Buena Vista oil field, steam will be injected in a test project to determine the commercial feasibility of using steam for the enhanced recovery of light crude oil. Also, in the McKittrick oil field, 2 processes are being considered for a commercial heavy oil mining venture. Steam continues to be the most important element in the recovery of hard-to-produce oil. Other steam-using projects are highlighted.

Rintoul, B.

1984-02-01T23:59:59.000Z

365

Oregon Hospital Heats Up with a Biomass Boiler | Department of...  

NLE Websites -- All DOE Office Websites (Extended Search)

Oregon Hospital Heats Up with a Biomass Boiler Oregon Hospital Heats Up with a Biomass Boiler December 27, 2012 - 4:30pm Addthis Using money from the Recovery Act, Blue Mountain...

366

American Recovery and Reinvestment Act  

Energy.gov (U.S. Department of Energy (DOE))

Here is one compliance agreement for EM’s American Recovery and Reinvestment Act Program on accelerated milestones for the Recovery Act program.

367

Experimental comparison of hot water/propane injection to steam/propane injection for recovery of heavy oil.  

E-Print Network (OSTI)

??Generating enough heat to convert water into steam is a major expense for projects that inject steam into reservoirs to enhance hydrocarbon recovery. If the… (more)

Nesse, Thomas

2005-01-01T23:59:59.000Z

368

Recovery News Flashes  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

news-flashes Office of Environmental news-flashes Office of Environmental Management 1000 Independence Ave., SW Washington, DC 20585 202-586-7709 en "TRU" Success: SRS Recovery Act Prepares to Complete Shipment of More Than 5,000 Cubic Meters of Nuclear Waste to WIPP http://energy.gov/em/downloads/tru-success-srs-recovery-act-prepares-complete-shipment-more-5000-cubic-meters-nuclear recovery-act-prepares-complete-shipment-more-5000-cubic-meters-nuclear" class="title-link">"TRU" Success: SRS Recovery Act Prepares to Complete Shipment of More Than 5,000 Cubic Meters of Nuclear Waste to WIPP

369

Heat pipe heat amplifier  

SciTech Connect

In a heat pipe combination consisting of a common condenser section with evaporator sections at either end, two working fluids of different vapor pressures are employed to effectively form two heat pipe sections within the same cavity to support an amplifier mode of operation.

Arcella, F.G.

1978-08-15T23:59:59.000Z

370

NGNP Process Heat Utilization: Liquid Metal Phase Change Heat Exchanger  

DOE Green Energy (OSTI)

One key long-standing issue that must be overcome to fully realize the successful growth of nuclear power is to determine other benefits of nuclear energy apart from meeting the electricity demands. The Next Generation Nuclear Plant (NGNP) will most likely be producing electricity and heat for the production of hydrogen and/or oil retrieval from oil sands and oil shale to help in our national pursuit of energy independence. For nuclear process heat to be utilized, intermediate heat exchange is required to transfer heat from the NGNP to the hydrogen plant or oil recovery field in the most efficient way possible. Development of nuclear reactor - process heat technology has intensified the interest in liquid metals as heat transfer media because of their ideal transport properties. Liquid metal heat exchangers are not new in practical applications. An important rational for considering liquid metals is the potential convective heat transfer is among the highest known. Thus explains the interest in liquid metals as coolant for intermediate heat exchange from NGNP. For process heat it is desired that, intermediate heat exchangers (IHX) transfer heat from the NGNP in the most efficient way possible. The production of electric power at higher efficiency via the Brayton Cycle, and hydrogen production, requires both heat at higher temperatures and high effectiveness compact heat exchangers to transfer heat to either the power or process cycle. Compact heat exchangers maximize the heat transfer surface area per volume of heat exchanger; this has the benefit of reducing heat exchanger size and heat losses. High temperature IHX design requirements are governed in part by the allowable temperature drop between the outlet and inlet of the NGNP. In order to improve the characteristics of heat transfer, liquid metal phase change heat exchangers may be more effective and efficient. This paper explores the overall heat transfer characteristics and pressure drop of the phase change heat exchanger with Na as the heat exchanger coolant. In order to design a very efficient and effective heat exchanger one must optimize the design such that we have a high heat transfer and a lower pressure drop, but there is always a trade-off between them. Based on NGNP operational parameters, a heat exchanger analysis with the sodium phase change will be presented to show that the heat exchanger has the potential for highly effective heat transfer, within a small volume at reasonable cost.

Piyush Sabharwall; Mike Patterson; Vivek Utgikar; Fred Gunnerson

2008-09-01T23:59:59.000Z

371

Radiant Heating  

Energy.gov (U.S. Department of Energy (DOE))

Radiant heating systems involve supplying heat directly to the floor or to panels in the walls or ceiling of a house. The systems depend largely on radiant heat transfer: the delivery of heat...

372

Hot tips on water heating  

SciTech Connect

Water-heater manufacturers responded to the call for energy conservation with innovations and efficiency standards for the home, business, and plant. Conventional tank-type water heaters offer better design and insulation, but the heat-pump water heater offers the highest efficiency. Available in add-on units and integral units, they now represent up to 40% of manufacturers' sales. Other advances are the desuperheater devices which recapture air-conditioner waste heat, solar-water-heating systems, instantaneous water heaters, and industrial heat-recovery systems for process water. 1 figure. (DCK)

Forker, J.

1982-03-01T23:59:59.000Z

373

Method for recovery of hydrocarbon material from hydrocarbon material-bearing formations  

SciTech Connect

A method is disclosed for heating a hydrocarbon material contained in a recovery zone in an underground hydrocarbon material-bearing formation to reduce the viscosity thereof for facilitating recovery of the hydrocarbon material. A gaseous penetration medium comprising a gaseous working fluid and a carrier gas, is fed into the formation at a penetration pressure sufficient for penetration of the recovery zone, the working fluid being a water soluble gas which generates heat of solution upon absorption in an aqueous medium, and in which the partial pressure of the working fluid in relation to the penetration pressure and the temperature prevailing in the recovery zone is controlled to inhibit working fluid condensation but to provide for absorption of working fluid by water present in the formation to release heat for heating the hydrocarbon material in the recovery zone.

Kalina, A.I.

1982-05-25T23:59:59.000Z

374

Engineering-Scale Distillation of Cadmium for Actinide Recovery  

Science Conference Proceedings (OSTI)

During the recovery of actinide products from spent nuclear fuel, cadmium is separated from the actinide products by a distillation process. Distillation occurs in an induction-heated furnace called a cathode processor capable of processing kilogram quantities of cadmium. Operating parameters have been established for sufficient recovery of the cadmium based on mass balance and product purity. A cadmium distillation rate similar to previous investigators has also been determined. The development of cadmium distillation for spent fuel treatment enhances the capabilities for actinide recovery processes.

J.C. Price; D. Vaden; R.W. Benedict

2007-10-01T23:59:59.000Z

375

Enhanced coalbed methane recovery  

SciTech Connect

The recovery of coalbed methane can be enhanced by injecting CO{sub 2} in the coal seam at supercritical conditions. Through an in situ adsorption/desorption process the displaced methane is produced and the adsorbed CO{sub 2} is permanently stored. This is called enhanced coalbed methane recovery (ECBM) and it is a technique under investigation as a possible approach to the geological storage of CO{sub 2} in a carbon dioxide capture and storage system. This work reviews the state of the art on fundamental and practical aspects of the technology and summarizes the results of ECBM field tests. These prove the feasibility of ECBM recovery and highlight substantial opportunities for interdisciplinary research at the interface between earth sciences and chemical engineering.

Mazzotti, M.; Pini, R.; Storti, G. [ETH, Zurich (Switzerland). Inst. of Process Engineering

2009-01-15T23:59:59.000Z

376

Secretary Chu Announces Nearly $50 Million of Recovery Act Funding to  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Secretary Chu Announces Nearly $50 Million of Recovery Act Funding Secretary Chu Announces Nearly $50 Million of Recovery Act Funding to Accelerate Deployment of Geothermal Heat Pumps Secretary Chu Announces Nearly $50 Million of Recovery Act Funding to Accelerate Deployment of Geothermal Heat Pumps June 2, 2009 - 12:00am Addthis WASHINGTON - During a visit to Fort Wayne, Indiana, where he toured a manufacturer of geothermal heating pumps (GHPs), U.S. Energy Secretary Steven Chu today announced nearly $50 million from the American Reinvestment and Recovery Act to advance commercial deployment of the renewable heating and cooling systems, which use energy from below the Earth's surface to move heat either into or away from the home or building. The expanded manufacturing and installation of GHPs could aid in the creation of new jobs while reducing the use of fossil fuels.

377

Secretary Chu Announces Nearly $50 Million of Recovery Act Funding to  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Secretary Chu Announces Nearly $50 Million of Recovery Act Funding Secretary Chu Announces Nearly $50 Million of Recovery Act Funding to Accelerate Deployment of Geothermal Heat Pumps Secretary Chu Announces Nearly $50 Million of Recovery Act Funding to Accelerate Deployment of Geothermal Heat Pumps June 2, 2009 - 12:00am Addthis WASHINGTON - During a visit to Fort Wayne, Indiana, where he toured a manufacturer of geothermal heating pumps (GHPs), U.S. Energy Secretary Steven Chu today announced nearly $50 million from the American Reinvestment and Recovery Act to advance commercial deployment of the renewable heating and cooling systems, which use energy from below the Earth's surface to move heat either into or away from the home or building. The expanded manufacturing and installation of GHPs could aid in the creation of new jobs while reducing the use of fossil fuels.

378

Apparatus and methods of reheating gas turbine cooling steam and high pressure steam turbine exhaust in a combined cycle power generating system  

DOE Patents (OSTI)

In a combined cycle system having a multi-pressure heat recovery steam generator, a gas turbine and steam turbine, steam for cooling gas turbine components is supplied from the intermediate pressure section of the heat recovery steam generator supplemented by a portion of the steam exhausting from the HP section of the steam turbine, steam from the gas turbine cooling cycle and the exhaust from the HP section of the steam turbine are combined for flow through a reheat section of the HRSG. The reheated steam is supplied to the IP section inlet of the steam turbine. Thus, where gas turbine cooling steam temperature is lower than optimum, a net improvement in performance is achieved by flowing the cooling steam exhausting from the gas turbine and the exhaust steam from the high pressure section of the steam turbine in series through the reheater of the HRSG for applying steam at optimum temperature to the IP section of the steam turbine.

Tomlinson, Leroy Omar (Niskayuna, NY); Smith, Raub Warfield (Ballston Lake, NY)

2002-01-01T23:59:59.000Z

379

Water heater heat reclaimer  

SciTech Connect

This invention relates to the conservation of energy in a domestic gas water heater by utilizing the hot exhaust gases in a gas water heater for the preheating of the incoming unheated water into the water heater. The exhaust gases from a domestic gas water heater carry wasted heat and the present invention provides a mean to reclaim part of the wasted heat for the preheating of the incoming unheated water during hot water usage periods. During non hot water usage periods the heat in the exhaust gases is not reclaimed to prevent overheating of the water and also to prevent the formation of water deposit in the preheating assembly or heat reclaimer. During the non hot water usage periods the heat produced in the water heater is normally needed only to maintain the desired water temperature of the stored water in the water tank of the water heater. Due to the rapid heating or recovery rate, the present invention enables the use of a smaller water heater. The use of a smaller water heater reduces the normal heat loss from the stored hot water thereby further reduces energy consumption.

Wie, C.T.

1983-08-09T23:59:59.000Z

380

Recycling and Secondary Recovery  

Science Conference Proceedings (OSTI)

"Applying Ausmelt Technology to Recover Cu, Ni, and Co from Slags" .... " Enhancing Cobalt Recovery from Primary and Secondary Resources" .... " Modifying Alumina Red Mud to Support a Revegetation Cover" (Research .... " Recycling Used Automotive Oil Filters" (Research Summary), K.D. Peaslee, February 1994, pp.

Note: This page contains sample records for the topic "hrsg heat recovery" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Method and apparatus for fuel gas moisturization and heating  

SciTech Connect

Fuel gas is saturated with water heated with a heat recovery steam generator heat source. The heat source is preferably a water heating section downstream of the lower pressure evaporator to provide better temperature matching between the hot and cold heat exchange streams in that portion of the heat recovery steam generator. The increased gas mass flow due to the addition of moisture results in increased power output from the gas and steam turbines. Fuel gas saturation is followed by superheating the fuel, preferably with bottom cycle heat sources, resulting in a larger thermal efficiency gain compared to current fuel heating methods. There is a gain in power output compared to no fuel heating, even when heating the fuel to above the LP steam temperature.

Ranasinghe, Jatila (Niskayuna, NY); Smith, Raub Warfield (Ballston Lake, NY)

2002-01-01T23:59:59.000Z

382

Determining the quality and quantity of heat produced by proton exchange membrane fuel cells with application to air-cooled stacks for combined heat and power  

E-Print Network (OSTI)

Determining the quality and quantity of heat produced by proton exchange membrane fuel cells Determining the quality and quantity of heat produced by proton exchange membrane fuel cells with application, the coolant is pumped to a heat recovery system. A water-to-air heat exchange system or water-to-water heat

Victoria, University of

383

Demonstration of Wear and Tear Sensors for Measurement of Damage  

Science Conference Proceedings (OSTI)

In 2005, Southern Company and EPRI initiated a small project to install and test wear and tear sensors on a combined-cycle, heat recovery steam generator (HRSG). The term wear and tear sensor refers to any sensor that provides insight into equipment degradation resulting from normal plant operation. For this project, the sensors were monitoring thermocouples and high-temperature strain gages. This report describes the installation of the sensors, the monitoring system, and the data collected during 80 da...

2006-03-30T23:59:59.000Z

384

Proceedings: 7th International Conference on Cycle Chemistry in Fossil Plants  

SciTech Connect

The purity of boiler water, feedwater, and steam is central to ensuring component availability and reliability in fossil-fired plants. These proceedings of EPRI's Seventh International Conference on Cycle Chemistry in Fossil Plants address the state of the art in fossil plant and combined cycle/heat recovery steam generator (HRSG) cycle chemistry as well as international practices for corrosion control and water preparation and purification.

None

2004-02-01T23:59:59.000Z

385

Advanced Control Demonstration on a Combined Cycle Plant  

Science Conference Proceedings (OSTI)

Southern Company, Electricit de France (EDF), and EPRI have undertaken a project to demonstrate the applicability of advanced control techniques on a combined-cycle heat recovery steam generator (HRSG). This report describes progress on the project during 2005 including model identification, the advanced controller design, controller program development, and controller testing in a simulation environment. A combined-cycle plant was selected as the host plant because many combined-cycle plants have chang...

2006-03-31T23:59:59.000Z

386

State of Knowledge for Advanced Bainitic Creep-Strength-Enhanced Ferritic Steel Grades 23 and 24  

Science Conference Proceedings (OSTI)

Two advanced, bainitic creep-strength-enhanced ferritic (CSEF) steels have recently been developed and introduced to construction codes governing power generation applications. These two materials, Grades 23 and 24, are actively being used across a wide range of boiler and heat recovery steam generator (HRSG) components including thick-section headers, loose tubing in reheaters and superheaters, and waterwall panels. The wide range of use presents a demanding situation in which these two materials ...

2013-11-25T23:59:59.000Z

387

Assessment of Amines for Fossil Plant Applications  

Science Conference Proceedings (OSTI)

The purity and proper chemical treatment of water and steam are central to ensuring fossil and heat recovery steam generator (HRSG) plant component availability and reliability, which are critical to the overall economic performance and profitability of plant unit operations. This report provides a technical assessment of neutralizing amines for application in plant cycles to improve the pH conditions in the low pressure (LP) evaporators and economizers of HRSGs, the phase transition zone (PTZ) of the LP...

2010-03-31T23:59:59.000Z

388

Heat Pipes: An Industrial Application  

E-Print Network (OSTI)

This paper reviews the basics of heat pipe exchangers. Included are how they are constructed, how they operate, where they have application, and various aspects of evaluating a potential application. After discussing the technical aspects of heat pipe exchangers, an industrial case history is presented. The case history involves a retrofit project which added heat pipes to five natural draft process heaters with a combined heat duty of 150 M Btu/hr. A heat recovery of 15 M Btu/hr has resulted from the flue gas/combustion air interchange. The paper will include design considerations, and operating and maintenance history since early 1980. A second application for heat pipes with a 12 M Btu/hr duty installed in 1983 will also be discussed.

Murray, F.

1984-01-01T23:59:59.000Z

389

Heating Alloys  

Science Conference Proceedings (OSTI)

...are used in many varied applications--from small household appliances to large industrial process heating systems and furnaces. In appliances or industrial process heating, the heating elements are usually either open

390

Recovery Act | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Recovery Act Recovery Act Recovery Act Center Map PERFORMANCE The Department estimates the $6 billion Recovery Act investment will allow us to complete work now that would cost approximately $13 billion in future years, saving $7 billion. As Recovery Act work is completed through the cleanup of contaminated sites, facilities, and material disposition, these areas will becoming available for potential reuse by other entities. Recovery Act funding is helping the Department reach our cleanup goals faster. Through the end of December 2012, EM achieved a total footprint reduction of 74%, or 690 of 931 square miles. EM achieved its goal of 40% footprint reduction in April 2011, five months ahead of schedule. Recovery Act payments exceeded $5.9 billion in December 2012. Recovery Act

391

Recovery Act | OpenEI  

Open Energy Info (EERE)

Recovery Act Recovery Act Dataset Summary Description This dataset, updated quarterly by Recovery.org, contains a breakdown of state-by-state recovery act funds awarded and received, as well as the number of jobs created and saved. The shows two periods, February 17, 2009 to December 31, 2010, and January 1, 2011 to March 31, 2011. The jobs created and saved are displayed just for January 1, 2011 to March 31, 2011. The document was downloaded from Recovery.org. It is a simple document displaying 50 states, as well as American territories. Source Recovery.org Date Released June 08th, 2011 (3 years ago) Date Updated Unknown Keywords award funding jobs Recovery Act Recovery.org Data text/csv icon recipientfundingawardedbystate.csv (csv, 5.1 KiB) Quality Metrics Level of Review Some Review

392

Ceramic heat pipes for high temperature heat removal  

SciTech Connect

Difficulties in finding metal or protected metal components that exhibit both strength and corrosion resistance at high temperature have severely restricted the application of effective heat recovery techniques to process heat furnaces. A potential method of overcoming this restriction is to use heat pipes fabricated from ceramic materials to construct counterflow recuperators. A development program has been initiated to demonstrate the technical and eventually the economical feasibility of ceramic heat pipes and ceramic heat pipe recuperators. The prime candidate for heat pipe construction is SiC. Closed-end tubes of this material have been prepared by chemical vapor deposition (CVD). These tubes were lined internally with tungsten by a subsequent CVD operation, partially filled with sodium, and sealed by brazing a tungsten lined SiC plug into the open-end with a palladium--cobalt alloy. Heat pipes constructed in this manner have been successfully operated in vacuum at temperatures of 1225/sup 0/K and in air at a temperature of 1125/sup 0/K. The heat source used initially for the air testing was an induction heated metallic sleeve in thermal contact with the test unit. Subsequent testing has shown that a silicon carbide heat pipe can be successfully operated with natural gas burners providing the input heat. Methods of fabricating and testing these devices are described.

Keddy, E.S.; Ranken, W.A.

1978-01-01T23:59:59.000Z

393

COLORADO RECOVERY ACT SNAPSHOT | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

COLORADO RECOVERY ACT SNAPSHOT COLORADO RECOVERY ACT SNAPSHOT The American Recovery & Reinvestment Act (ARRA) is making a meaningful down payment on the nation's energy and...

394

Heating Systems  

Energy.gov (U.S. Department of Energy (DOE))

A variety of heating technologies are available today. In addition to heat pumps, which are discussed separately, many homes and buildings use the following approaches:

395

Symposium on enhanced oil recovery  

SciTech Connect

The Second Joint Symposium on Enhanced Oil Recovery was held in Tulsa, Oklahoma on April 5 to 8, 1981. Forty-four technical papers were presented which covered all phases of enhanced oil recovery. Field tests, laboratory investigations, and mathematical analyses of tertiary recovery methods such as microemulsion flooding, carbon dioxide injection, in-situ combustion, steam injection, and gas injection are presented.

Not Available

1981-01-01T23:59:59.000Z

396

Caustic Recovery Technology  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

366, REVISON 0 366, REVISON 0 Key Words: Waste Treatment Plant Sodium Recovery Electrochemical Retention: Permanent Review of Ceramatec's Caustic Recovery Technology W. R. Wilmarth D. T. Hobbs W. A. Averill E. B. Fox R. A. Peterson UNCLASSIFIED DOES NOT CONTAIN UNCLASSIFIED CONTROLLED NUCLEAR INFORMATION ADC & Reviewing Official:_______________________________________ (E. Stevens, Manager, Solid Waste and Special Programs) Date:______________________________________ JULY 20, 2007 Washington Savannah River Company Savannah River Site Aiken, SC 29808 Prepared for the U. S. Department of Energy Under Contract Number DE-AC09-96SR18500 Page 1 of 28 WSRC-STI-2007-00366, REVISON 0 DISCLAIMER This report was prepared for the United States Department of Energy under

397

Fermilab | Recovery Act | Videos  

NLE Websites -- All DOE Office Websites (Extended Search)

Videos Videos Watch videos documenting progress on Fermilab projects funded by the American Recovery and Reinvestment Act. NOvA - Community Voices - September 2009 Residents of northern Minnesota and construction workers building the NOvA detector facility discuss the benefits the high-energy physics research project has brought their communities. Congressman Bill Foster at Fermilab Congressman Bill Foster speaks to Fermilab Technical Division employees and members of the media at a press conference on Wednesday, August 5 to announce an additional $60.2 million in Recovery Act funds for the lab. NOvA first blast On July 20, construction crews began blasting into the rock at the future site of the NOvA detector facility in northern Minnesota. NOvA groundbreaking ceremony

398

Fermilab | Recovery Act | Features  

NLE Websites -- All DOE Office Websites (Extended Search)

Features - Archive Features - Archive photo Industrial Building 3 addition Fermilab Today-November 5, 2010 IB3 addition nears completion The future site of FermilabÂ’s new materials laboratory space has evolved from a steel outline to a fully enclosed building over the past five months. Read full column photo Fermilab Today-October 22, 2010 Recovery Act gives LBNE team chance to grow Thanks to funding from the American Recovery and Reinvestment Act, the collaboration for the Long-Baseline Neutrino Experiment, LBNE, has expanded its project team. Read full column photo cooling units Fermilab Today-October 15, 2010 Local company completes FCC roof construction A local construction company recently completed work on the roof of the Feynman Computing Center, an important step in an ongoing project funded by

399

Elemental sulfur recovery process  

DOE Patents (OSTI)

An improved catalytic reduction process for the direct recovery of elemental sulfur from various SO[sub 2]-containing industrial gas streams. The catalytic process provides combined high activity and selectivity for the reduction of SO[sub 2] to elemental sulfur product with carbon monoxide or other reducing gases. The reaction of sulfur dioxide and reducing gas takes place over certain catalyst formulations based on cerium oxide. The process is a single-stage, catalytic sulfur recovery process in conjunction with regenerators, such as those used in dry, regenerative flue gas desulfurization or other processes, involving direct reduction of the SO[sub 2] in the regenerator off gas stream to elemental sulfur in the presence of a catalyst. 4 figures.

Flytzani-Stephanopoulos, M.; Zhicheng Hu.

1993-09-07T23:59:59.000Z

400

Heavy crude oil recovery  

SciTech Connect

The oil crisis of the past decade has focused most of the attention and effort of researchers on crude oil resources, which are accepted as unrecoverable using known technology. World reserves are estimated to be 600-1000 billion metric tons, and with present technology 160 billion tons of this total can be recovered. This book is devoted to the discussion of Enhanced Oil Recovery (EOR) techniques, their mechanism and applicability to heavy oil reservoirs. The book also discusses some field results. The use of numerical simulators has become important, in addition to laboratory research, in analysing the applicability of oil recovery processes, and for this reason the last section of the book is devoted to simulators used in EOR research.

Okandan, E.

1984-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "hrsg heat recovery" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Recovery Boiler Modeling  

E-Print Network (OSTI)

Preliminary computations of the cold flow in a simplified geometry of a recovery boiler are presented. The computations have been carried out using a new code containing multigrid methods and segmentation techniques. This approach is shown to provide good resolution of the complex flow near the air ports and greatly improve the convergence characteristics of the numerical procedure. The improved resolution enhances the predictive capabilities of the computations, and allows the assessment of the relative performance of different air delivery systems.

Abdullah, Z.; Salcudean, M.; Nowak, P.

1994-04-01T23:59:59.000Z

402

Chemically enhanced oil recovery  

Science Conference Proceedings (OSTI)

Yet when conducted according to present state of the art, chemical flooding (i.e., micellar/polymer flooding, surfactant/polymer flooding, surfactant flooding) can mobilize more residual crude oil than any other method of enhanced oil recovery. It also is one of the most expensive methods of enhanced oil recovery. This contribution will describe some of the technology that comprises the state of the art technology that must be adhered to if a chemical flood is to be successful. Although some of the efforts to reduce cost and other points are discussed, the principle focus is on technical considerations in designing a good chemical flooding system. The term chemical flooding is restricted here to methods of enhanced oil recovery that employs a surfactant, either injected into the oil reservoir or generated in situ, primarily to reduce oil-water interfacial tension. Hence, polymer-water floods for mobility or profile control, steam foams, and carbon dioxide foams are excluded. Some polymer considerations are mentioned because they apply to providing mobility control for chemical flooding systems.

Nelson, R.C.

1989-03-01T23:59:59.000Z

403

Spatio-Temporal Signal Recovery from Political Tweets in Indonesia  

E-Print Network (OSTI)

Spatio-Temporal Signal Recovery from Political Tweets in Indonesia Anisha Mazumder, Arun Das activity in the provinces of Indonesia. Based on analysis of radical/counter radical sentiments expressed in tweets by Twitter users, we create a Heat Map of Indonesia which visually demonstrates the degree

Davulcu, Hasan

404

A Kinetics Study on the Hydrometallurgical Recovery of Vanadium ...  

Science Conference Proceedings (OSTI)

In this research, recovery of vanadium from LD converter slag of steelmaking plant ... of the Chemical Changes and Surface Properties of Carbonated Waste Cement ... Flux for Basic Oxygen Steel Making Using Waste Oxides of Steel Plant ... Heat Treatment of Black Dross for the Production of a Value Added Material - A

405

Leaching Studies for Metals Recovery from Waste Printed Wiring ...  

Science Conference Proceedings (OSTI)

Presentation Title, Leaching Studies for Metals Recovery from Waste Printed Wiring ... of the Chemical Changes and Surface Properties of Carbonated Waste Cement ... Flux for Basic Oxygen Steel Making Using Waste Oxides of Steel Plant ... Heat Treatment of Black Dross for the Production of a Value Added Material - A

406

Iron Recovery from Copper Slag through Oxidation-magnetic ...  

Science Conference Proceedings (OSTI)

Recovery of iron from the copper slag is very essential not only for recycling the valuable ... Characterization of High-arsenic Sludge in Copper Metallurgy Plant ... Characterization of Waste from Ornamental Stones for Use in Mortar ... Effect of Friction Stir Welding Speed and Post Weld Heat Treatment on the Microstructure

407

EA-1769: Battleground Energy Recovery Project, Harris County, Texas |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

69: Battleground Energy Recovery Project, Harris County, Texas 69: Battleground Energy Recovery Project, Harris County, Texas EA-1769: Battleground Energy Recovery Project, Harris County, Texas Summary This EA evaluates the environmental impacts of a proposal to provide $1.94 million in cost-shared funding to the Houston Advanced Research Center for the Battleground Energy Recovery Project, which would produce 8 megawatts of electricity from high pressure steam generated by capturing heat that is currently lost at the Clean Harbors Deer Park facility. The proposed project was selected by the DOE's Office of Energy Efficiency and Renewable Energy to advance research and demonstration of energy efficiency and renewable energy technologies. Public Comment Opportunities No public comment opportunities available at this time.

408

HRSG Life Assessment-Case Studies  

Science Conference Proceedings (OSTI)

Many power plant pressure parts, particularly those exposed to high temperatures and/or cyclic stresses, have a finite design life. Creep and/or fatigue damage is anticipated by the designer to accumulate at predictable rates based upon knowledge of the material’s response to stresses imposed on the component. Key factors associated with determining these stress values and the specific locations where stress values are highest include component geometry, static and dynamic operating pressures, ...

2013-12-20T23:59:59.000Z

409

Heat pipe theory and practice: a sourcebook  

SciTech Connect

An introduction to heat pipe operating principles, types, and applications followed by a comprehensive treatment of heat pipe theory, design, and manufacture are presented. The organization of heat pipe theory provides parallel treatment of the fundamental laws of thermodynamics, heat transfer, fluid mechanics, and materials science during heat pipe analysis. For the problem-solving convenience of practicing engineers, design procedures are developed summarizing theoretical information. Methods of summarizing voluminous research information are presented in detail. Current practices in the manufacture of heat pipes are described. Current and potential applications of the heat pipe to energy systems discussed are: heat exchangers, heat recovery for HVAC systems, residential buildings, industrial processes, gasification plants, and thermal storage subsystems.

Chi, S.W.

1976-01-01T23:59:59.000Z

410

Comprehensive Municipal Solid Waste Management, Resource Recovery...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Municipal Solid Waste Management, Resource Recovery, and Conservation Act (Texas) Comprehensive Municipal Solid Waste Management, Resource Recovery, and Conservation...

411

Categorical Exclusion Determinations: American Recovery and Reinvestment  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

9, 2010 9, 2010 CX-004104: Categorical Exclusion Determination State Energy Program Conductor Optimized Rotary Energy Mega-Watt Scale Direct Wind Generator CX(s) Applied: A9, B5.1 Date: 09/29/2010 Location(s): Ronan, Montana Office(s): Energy Efficiency and Renewable Energy, Golden Field Office September 28, 2010 CX-004168: Categorical Exclusion Determination Modeling Variable Refrigerant Flow Heat Pump and Heat Recovery Equipment in EnergyPlus CX(s) Applied: A1, A9, B2.2, B3.6, B5.1 Date: 09/28/2010 Location(s): Brevard County, Florida Office(s): Energy Efficiency and Renewable Energy, National Energy Technology Laboratory September 27, 2010 CX-004077: Categorical Exclusion Determination Replacement of a Relay/Transfer Trip Rack at Redmond Substation and a Transfer Trip Panel at LaPine Substation

412

System Modeling of Gas Engine Driven Heat Pump  

SciTech Connect

To improve the system performance of the GHP, modeling and experimental study has been made by using desiccant system in cooling operation (particularly in high humidity operations) and suction line waste heat recovery to augment heating capacity and efficiency. The performance of overall GHP system has been simulated by using ORNL Modulating Heat Pump Design Software, which is used to predict steady-state heating and cooling performance of variable-speed vapor compression air-to-air heat pumps for a wide range of operational variables. The modeling includes: (1) GHP cycle without any performance improvements (suction liquid heat exchange and heat recovery) as a baseline (both in cooling and heating mode), (2) the GHP cycle in cooling mode with desiccant system regenerated by waste heat from engine incorporated, (3) GHP cycle in heating mode with heat recovery (recovered heat from engine). According to the system modeling results, by using desiccant system regenerated by waste heat from engine, the SHR can be lowered to 40%. The waste heat of the gas engine can boost the space heating efficiency by 25% in rated operating conditions.

Mahderekal, Isaac [Oak Ridge National Laboratory (ORNL); Shen, Bo [ORNL; Vineyard, Edward [Oak Ridge National Laboratory (ORNL)

2012-01-01T23:59:59.000Z

413

URANIUM RECOVERY PROCESS  

DOE Patents (OSTI)

A method is described for recovering uranium values from uranium bearing phosphate solutions such as are encountered in the manufacture of phosphate fertilizers. The solution is first treated with a reducing agent to obtain all the uranium in the tetravalent state. Following this reduction, the solution is treated to co-precipitate the rcduced uranium as a fluoride, together with other insoluble fluorides, thereby accomplishing a substantially complete recovery of even trace amounts of uranium from the phosphate solution. This precipitate usually takes the form of a complex fluoride precipitate, and after appropriate pre-treatment, the uranium fluorides are leached from this precipitate and rccovered from the leach solution.

Bailes, R.H.; Long, R.S.; Olson, R.S.; Kerlinger, H.O.

1959-02-10T23:59:59.000Z

414

The ALEXIS mission recovery  

SciTech Connect

The authors report the recovery of the ALEXIS small satellite mission. ALEXIS is a 113-kg satellite that carries an ultrasoft x-ray telescope array and a high-speed VHF receiver/digitizer (BLACKBEARD), supported by a miniature spacecraft bus. It was launched by a Pegasus booster on 1993 April 25, but a solar paddle was damaged during powered flight. Initial attempts to contact ALEXIS were unsuccessful. The satellite finally responded in June, and was soon brought under control. Because the magnetometer had failed, the rescue required the development of new attitude control-techniques. The telemetry system has performed nominally. They discuss the procedures used to recover the ALEXIS mission.

Bloch, J.; Armstrong, T.; Dingler, B.; Enemark, D.; Holden, D.; Little, C.; Munson, C.; Priedhorsky, B.; Roussel-Dupre, D.; Smith, B. [Los Alamos National Lab., NM (United States); Warner, R.; Dill, B.; Huffman, G.; McLoughlin, F.; Mills, R.; Miller, R. [AeroAstro, Inc., Herndon, VA (United States)

1994-03-01T23:59:59.000Z

415

Industrial and Commercial Heat Pump Applications in the United States  

E-Print Network (OSTI)

The energy crisis of 1973 accelerated the development of large-scale heat pumps in the United States. Since that time, the commercial, institutional, and industrial applications of heat pumps for waste heat recovery have expanded. This paper reviews the trends in heat pump cycle developments and discusses both the closed vapor compression cycle and refrigerants most commonly used and the open-cycle mechanical vapor compression heat pumps. Waste heat sources, heat loads served by heat pumps--and typical applications using heat pumps for large-scale space heating, domestic water heating, and industrial process water heating-- are discussed. Typical installations include commercial applications in hotels, high-rise apartments and condominiums, and office buildings. Institutional installations discussed include hospitals, universities, wastewater treatment plants, and airport terminals. Industrial applications largely center on food processing industries, feedwater heating, metal fabricating, and other industries. Reference is also made to other applications and alternative energy sources now gaining acceptance, including groundwater/geothermal water.

Niess, R. C.

1986-06-01T23:59:59.000Z

416

Recovery Act State Memos Ohio  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

20 20 For total Recovery Act jobs numbers in Ohio go to www.recovery.gov DOE Recovery Act projects in Ohio: 83 U.S. DEPARTMENT OF ENERGY * OHIO RECOVERY ACT SNAPSHOT The American Recovery & Reinvestment Act (ARRA) is making a meaningful down payment on the nation's energy and environmental future. The Recovery Act investments in Ohio are supporting a broad range of clean energy projects from the smart grid and energy efficiency to advanced battery manufacturing, biofuels, carbon capture and storage, and cleanup of the state's Cold War legacy nuclear sites Through these investments, Ohio's businesses, universities, non-profits, and local governments are creating quality jobs today and positioning Ohio to play an important role in the new energy economy of the future. EXAMPLES OF OHIO FORMULA GRANTS Program

417

Recovery Act | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Energy Economy » Recovery Act Energy Economy » Recovery Act Recovery Act December 18, 2013 BPA Wins Platts Global Energy Award for Grid Optimization Platts awarded the Bonneville Power Administration (BPA) a Global Energy Award for grid optimization on December 12 in New York City for its development of a synchrophasor network. BPA is part of the Recovery Act-funded Western Interconnection Synchrophasor Program. December 13, 2013 Cumulative Federal Payments to OE Recovery Act Recipients, through November 30, 2013 Graph of cumulative Federal Payments to OE Recovery Act Recipients, through November 30, 2013. December 12, 2013 Energy Department Announces $150 Million in Tax Credits to Invest in U.S. Clean Energy Manufacturing Domestic Manufacturing Projects to Support Renewable Energy Generation as

418

Resource Conservation and Recovery Act  

NLE Websites -- All DOE Office Websites (Extended Search)

Resource Conservation and Recovery Act (RCRA) Resource Conservation and Recovery Act (RCRA) In 1965 the Solid Waste Disposal Act [Public Law (Pub. L.) 89-72] was enacted to improve solid waste disposal methods. It was amended in 1970 by the Resource Recovery Act (Pub. L. 91-512), which provided the Environmental Protection Agency (EPA) with funding for resource recovery programs. However, that Act had little impact on the management and ultimate disposal of hazardous waste. In 1976 Congress enacted the Resource Conservation and Recovery Act (RCRA, Pub. L. 94-580). RCRA established a system for managing non-hazardous and hazardous solid wastes in an environmentally sound manner. Specifically, it provides for the management of hazardous wastes from the point of origin to the point of final disposal (i.e., "cradle to grave"). RCRA also promotes resource recovery and waste minimization.

419

Recovery Act State Memos Louisiana  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Louisiana Louisiana For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

420

Recovery Act State Memos Alabama  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Alabama Alabama For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

Note: This page contains sample records for the topic "hrsg heat recovery" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Recovery Act State Memos Oklahoma  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Oklahoma Oklahoma For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

422

Recovery Act State Memos Massachusetts  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Massachusetts Massachusetts For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

423

Recovery Act State Memos Mississippi  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Mississippi Mississippi For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 4

424

Recovery Act State Memos Wyoming  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Wyoming Wyoming For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 ELECTRIC GRID ........................................................................................................ 4

425

Recovery Act State Memos Connecticut  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Connecticut Connecticut For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 4

426

Recovery Act State Memos Oregon  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Oregon Oregon For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 4 RENEWABLE ENERGY ............................................................................................. 5

427

Recovery Act State Memos Utah  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Utah Utah For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

428

Recovery Act State Memos Nebraska  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Nebraska Nebraska For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 4

429

Recovery Act State Memos Alaska  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Alaska Alaska For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

430

Recovery Act State Memos Arkansas  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Arkansas Arkansas For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 4

431

Recovery Act State Memos Indiana  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Indiana Indiana For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

432

Recovery Act State Memos Guam  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Guam Guam For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 ELECTRIC GRID ........................................................................................................ 4

433

Recovery Act State Memos Iowa  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Iowa Iowa For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 4

434

Recovery Act State Memos Georgia  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Georgia Georgia For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

435

Recovery Act State Memos Minnesota  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Minnesota Minnesota For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

436

Recovery Act State Memos Idaho  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Idaho Idaho For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 4

437

Recovery Act State Memos Illinois  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Illinois Illinois For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 7

438

Recovery Act State Memos Pennsylvania  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Pennsylvania Pennsylvania For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................ 3 RENEWABLE ENERGY ......................................................................................... 7

439

Recovery Act State Memos Wisconsin  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Wisconsin Wisconsin For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 6

440

Recovery Act State Memos Montana  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Montana Montana For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 4

Note: This page contains sample records for the topic "hrsg heat recovery" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Recovery Act State Memos Arizona  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Arizona Arizona For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

442

Recovery Act State Memos Kansas  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Kansas Kansas For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

443

Recovery Act State Memos California  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

California California For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY .............................................................................................. 3 RENEWABLE ENERGY ............................................................................................ 12

444

Recovery Act State Memos Washington  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Washington Washington For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 6

445

Recovery Act State Memos Nevada  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Nevada Nevada For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ................................................................................................ 1 RENEWABLE ENERGY ............................................................................................. 5

446

Recovery Act State Memos Virginia  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Virginia Virginia For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

447

Recovery Act State Memos Maine  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Maine Maine For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 4

448

Recovery Act State Memos Missouri  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Missouri Missouri For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

449

Recovery Act State Memos Maryland  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Maryland Maryland For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ....................................................................................................... 3 RENEWABLE ENERGY ..................................................................................................... 4

450

Recovery Act State Memos Colorado  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Colorado Colorado For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 6

451

Recovery Act State Memos Texas  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Texas Texas For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 7

452

Recovery Act State Memos Vermont  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Vermont Vermont For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................ 4

453

Recovery Act State Memos Michigan  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Michigan Michigan For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 4

454

Recovery Act State Memos Tennessee  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Tennessee Tennessee For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 5

455

Recovery Act State Memos Hawaii  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Hawaii Hawaii For questions about DOE's Recovery Act activities, please contact the DOE Recovery Act Clearinghouse: 1-888-DOE-RCVY (888-363-7289), Monday through Friday, 9 a.m. to 7 p.m. Eastern Time https://recoveryclearinghouse.energy.gov/contactUs.htm. All numbers and projects listed as of June 1, 2010 TABLE OF CONTENTS RECOVERY ACT SNAPSHOT................................................................................... 1 FUNDING ALLOCATION TABLE.............................................................................. 2 ENERGY EFFICIENCY ............................................................................................... 3 RENEWABLE ENERGY ............................................................................................. 4

456

Cement Kiln Flue Gas Recovery Scrubber Project  

SciTech Connect

The Cement Kiln Flue Gas Recovery Scrubber Project was a technical success and demonstrated the following: CKD can be used successfully as the sole reagent for removing SO2 from cement kiln flue gas, with removal efficiencies of 90 percent or greater; Removal efficiencies for HCl and VOCs were approximately 98 percent and 70 percent, respectively; Particulate emissions were low, in the range of 0.005 to 0.007 grains/standard cubic foot; The treated CKD sorbent can be recycled to the kiln after its potassium content has been reduced in the scrubber, thereby avoiding the need for landfilling; The process can yield fertilizer-grade K2SO4, a saleable by-product; and Waste heat in the flue gas can provide the energy required for evaporation and crystallization in the by-product recovery operation. The demonstration program established the feasibility of using the Recovery Scrubber{trademark} for desulfurization of flue gas from cement kilns, with generally favorable economics, assuming tipping fees are available for disposal of ash from biomass combustion. The process appears to be suitable for commercial use on any type of cement kiln. EPA has ruled that CKD is a nonhazardous waste, provided the facility meets Performance Standards for the Management of CKD (U.S. Environmental Protection Agency 1999d). Therefore, regulatory drivers for the technology focus more on reduction of air pollutants and pollution prevention, rather than on treating CKD as a hazardous waste. Application of the Recovery Scrubbe{trademark} concept to other waste-disposal operations, where pollution and waste reductions are needed, appears promising.

National Energy Technology Laboratory

2001-11-30T23:59:59.000Z

457

PREDICTIVE MODELS. Enhanced Oil Recovery Model  

SciTech Connect

PREDICTIVE MODELS is a collection of five models - CFPM, CO2PM, ICPM, PFPM, and SFPM - used in the 1982-1984 National Petroleum Council study of enhanced oil recovery (EOR) potential. Each pertains to a specific EOR process designed to squeeze additional oil from aging or spent oil fields. The processes are: 1 chemical flooding, where soap-like surfactants are injected into the reservoir to wash out the oil; 2 carbon dioxide miscible flooding, where carbon dioxide mixes with the lighter hydrocarbons making the oil easier to displace; 3 in-situ combustion, which uses the heat from burning some of the underground oil to thin the product; 4 polymer flooding, where thick, cohesive material is pumped into a reservoir to push the oil through the underground rock; and 5 steamflood, where pressurized steam is injected underground to thin the oil. CFPM, the Chemical Flood Predictive Model, models micellar (surfactant)-polymer floods in reservoirs, which have been previously waterflooded to residual oil saturation. Thus, only true tertiary floods are considered. An option allows a rough estimate of oil recovery by caustic or caustic-polymer processes. CO2PM, the Carbon Dioxide miscible flooding Predictive Model, is applicable to both secondary (mobile oil) and tertiary (residual oil) floods, and to either continuous CO2 injection or water-alternating gas processes. ICPM, the In-situ Combustion Predictive Model, computes the recovery and profitability of an in-situ combustion project from generalized performance predictive algorithms. PFPM, the Polymer Flood Predictive Model, is switch-selectable for either polymer or waterflooding, and an option allows the calculation of the incremental oil recovery and economics of polymer relative to waterflooding. SFPM, the Steamflood Predictive Model, is applicable to the steam drive process, but not to cyclic steam injection (steam soak) processes.

Ray, R.M. [DOE Bartlesville Energy Technology Technology Center, Bartlesville, OK (United States)

1992-02-26T23:59:59.000Z

458

Heat Conduction  

Science Conference Proceedings (OSTI)

Table 2   Differential equations for heat conduction in solids...conduction in solids General form with variable thermal properties General form with constant thermal properties General form, constant properties, without heat

459

Recovery Act | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Research and Commercialization New green jobs a benefit of effort to end dependence on foreign oil April 29, 2009 Secretary Chu Announces 93 Million from Recovery Act to...

460

Economic Recovery Loan Program (Maine)  

Energy.gov (U.S. Department of Energy (DOE))

The Economic Recovery Loan Program provides subordinate financing to help businesses remain viable and improve productivity. Eligibility criteria are based on ability to repay, and the loan is...

Note: This page contains sample records for the topic "hrsg heat recovery" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Recovery Act | Department of Energy  

NLE Websites -- All DOE Office Websites (Extended Search)

Reports Calendar Year Reports Recovery Act Peer Reviews DOE Directives Performance Strategic Plan Testimony Financial Statements Semiannual Reports Work Plan Mission About Us...

462

Recovery Act State Memos Delaware  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

weatherization efforts in the state, creating jobs, reducing carbon emissions, and saving money for Delaware's low-income families. Over the course of the Recovery Act,...

463

The economics of repowering steam turbines  

SciTech Connect

Repowering is defined as displacing steam presently generated in an existing fossil fuel fired boiler with a gas turbine-heat recovery steam generator (HRSG) system. The steam generated in the HRSG is expanded in the existing steam turbine generator. Repowering advantages include a significant increase in power output at an improved heat rate relative to the base value for the existing steam turbine cycle being repowered. In addition, the reduction in emissions can be advantageous in most locations. This paper discusses application and economic considerations associated with repowering. In addition, an illustration will show how repowering coal fired steam turbine systems may prove economic relative to retrofit scrubbers and/or low sulfur coal fuel substitution that may be part of the forthcoming acid rain legislation.

Kovacik, J.M.; Stoll, H.G. (General Electric Co., Schenectady, NY (United States))

1990-01-01T23:59:59.000Z

464

Heat exchanger  

DOE Patents (OSTI)

A heat exchanger is provided having first and second fluid chambers for passing primary and secondary fluids. The chambers are spaced apart and have heat pipes extending from inside one chamber to inside the other chamber. A third chamber is provided for passing a purge fluid, and the heat pipe portion between the first and second chambers lies within the third chamber.

Daman, Ernest L. (Westfield, NJ); McCallister, Robert A. (Mountain Lakes, NJ)

1979-01-01T23:59:59.000Z

465

High efficiency shale oil recovery  

SciTech Connect

The overall project objective is to demonstrate the high efficiency of the Adams Counter-Current shale oil recovery process. The efficiency will first be demonstrated at bench-scale, in the current phase, after which the demonstration will be extended to the operation of a small pilot plant. Thus the immediate project objective is to obtain data on oil shale retorting operations in a small batch rotary kiln that will be representative of operations in the proposed continuous process pilot plant. Although a batch oil shale sample will be sealed in the batch kiln from the start until the end of the run, the process conditions for the batch will be the same as the conditions that an element of oil shale would encounter in a large continuous process kiln. For example, similar conditions of heat-up rate (20 deg F/min during the pyrolysis), oxidation of the residue and cool-down will prevail for the element in both systems. This batch kiln is a unit constructed in a 1987 Phase I SBIR tar sand retorting project. The kiln worked fairly well in that project; however, the need for certain modifications was observed. These modifications are now underway to simplify the operation and make the data and analysis more exact. The agenda for the first three months of the project consisted of the first of nine tasks and was specified as the following four items: 1. Sample acquisition and equipment alteration: Obtain seven oil shale samples, of varying grade each 10 lb or more, and samples of quartz sand. Order equipment for kiln modification. 3. Set up and modify kiln for operation, including electric heaters on the ends of the kiln. 4. Connect data logger and make other repairs and changes in rotary batch kiln.

Adams, D.C.

1992-01-01T23:59:59.000Z

466

Potential of the heat pipe in coal gasification processes  

SciTech Connect

The declining production of natural gas in the United States has provided great impetus to the development of economcal methods of producing methane from coal. Coal gasification systems share in common a need for highly efficient heat transfer and energy recovery methods in order to maximize the coal-methane conversion efficiency. Characteristics of heat pipe heat transfer units that offer potential for increasing conversion efficiency and/or reducing production costs include: (1) complete physical separation of process streams, (2) capability of handling more than two process streams in a single unit, (3) heat removal at near-constant temperature, (4) high heat recovery efficiency, (5) low operating cost-with no requirement for auxiliary power, and (6) relative ease of cleaning. Design concepts incorporating heat pipes into indirect coal gasification units, methanators, and energy recovery units are presented and technological impediments that must be surmounted in the successful development of these units are discussed.

Ranken, W.A.

1976-01-01T23:59:59.000Z