Powered by Deep Web Technologies
Note: This page contains sample records for the topic "horizontal axis wind" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Yaw dynamics of horizontal axis wind turbines  

DOE Green Energy (OSTI)

Designers of a horizontal axis wind turbine yaw mechanism are faced with a difficult decision. They know that if they elect to use a yaw- controlled rotor then the system will suffer increased initial cost and increased inherent maintenance and reliability problems. On the other hand, if they elect to allow the rotor to freely yaw they known they will have to account for unknown and random, though bounded, yaw rates. They will have a higher-risk design to trade-off against the potential for cost savings and reliability improvement. The risk of a yaw-free system could be minimized if methods were available for analyzing and understanding yaw behavior. The complexity of yaw behavior has, until recently, discouraged engineers from developing a complete yaw analysis method. The objectives of this work are to (1) provide a fundamental understanding of free-yaw mechanics and the design concepts most effective at eliminating yaw problems, and (2) provide tested design tools and guidelines for use by free-yaw wind systems manufacturers. The emphasis is on developing practical and sufficiently accurate design methods.

Hansen, A.C. (Utah Univ., Salt Lake City, UT (United States))

1992-05-01T23:59:59.000Z

2

Experimental and theoretical study of horizontal-axis wind turbines  

E-Print Network (OSTI)

in many of the large machines which are now operating . 1.2 Recent developments (prior to 1978) Since 1973 wind power has grown at a very rapid rate in both Europe and America. The number of horizontal-axis wind turbines which have been built... .1 Introduction 9.2 Wind velocity measurement 9.3 Concluding remarks re wind velocity measurement 9.4 Power vs. wind speed 9.5 POWer coefficient vs. tip speed ratio 9.6 Conclusions Chapter 10. Summary of conclusions and suggestions for further research...

Anderson, Michael Broughton

1981-10-20T23:59:59.000Z

3

Study on Aerodynamic Design of Horizontal Axis Wind Turbine Generator System  

Science Conference Proceedings (OSTI)

In this paper the choosing principles of design parameters and multi-airfoils in horizontal axis wind turbine (HAWT) generator system aerodynamic design are introduced. On the basis of the comparison analysis of wind turbine aerodynamic design method ... Keywords: Schmitz, airfoil, partial load, horizontal axis wind turbine (HAWT), blade tip speed ratio (BTSR)

Li Dong; Mingfu Liao; Yingfeng Li; Xiaoping Song; Ke Xu

2009-10-01T23:59:59.000Z

4

Simulation and modeling of flow field around a horizontal axis wind turbine (HAWT) using RANS method.  

E-Print Network (OSTI)

??The principal objective of the proposed CFD analysis is to investigate the flow field around a horizontal axis wind turbine rotor and calculate the turbine's… (more)

Sargsyan, Armen.

2010-01-01T23:59:59.000Z

5

Determination of Elastic Twist in Horizontal Axis Wind Turbines (HAWTs)  

DOE Green Energy (OSTI)

This report presents the results of a project at the Alternative Energy Institute (AEI) which measured and calculated the elastic twist of three representative composite horizontal-axis blades: Carter 300, Gougeon ESI 54, and UTRC 8 kW.

Stoddard, F.; Nelson, V.; Starcher, K.; Andrews, B.

2006-06-01T23:59:59.000Z

6

Review of wind simulation methods for horizontal-axis wind turbine analysis  

DOE Green Energy (OSTI)

This report reviews three reports on simulation of winds for use in wind turbine fatigue analysis. The three reports are presumed to represent the state of the art. The Purdue and Sandia methods simulate correlated wind data at two points rotating as on the rotor of a horizontal-axis wind turbine. The PNL method at present simulates only one point, which rotates either as on a horizontal-axis wind turbine blade or as on a vertical-axis wind turbine blade. The spectra of simulated data are presented from the Sandia and PNL models under comparable input conditions, and the energy calculated in the rotational spikes in the spectra by the two models is compared. Although agreement between the two methods is not impressive at this time, improvement of the Sandia and PNL methods is recommended as the best way to advance the state of the art. Physical deficiencies of the models are cited in the report and technical recommendations are made for improvement. The report also reviews two general methods for simulating single-point data, called the harmonic method and the white noise method. The harmonic method, which is the basis of all three specific methods reviewed, is recommended over the white noise method in simulating winds for wind turbine analysis.

Powell, D.C.; Connell, J.R.

1986-06-01T23:59:59.000Z

7

Combined Experiment Phase 1. [Horizontal axis wind turbines: wind tunnel testing versus field testing  

DOE Green Energy (OSTI)

How does wind tunnel airfoil data differ from the airfoil performance on an operating horizontal axis wind turbine (HAWT) The National Renewable Energy laboratory has been conducting a comprehensive test program focused on answering this question and understanding the basic fluid mechanics of rotating HAWT stall aerodynamics. The basic approach was to instrument a wind rotor, using an airfoil that was well documented by wind tunnel tests, and measure operating pressure distributions on the rotating blade. Based an the integrated values of the pressure data, airfoil performance coefficients were obtained, and comparisons were made between the rotating data and the wind tunnel data. Care was taken to the aerodynamic and geometric differences between the rotating and the wind tunnel models. This is the first of two reports describing the Combined Experiment Program and its results. This Phase I report covers background information such as test setup and instrumentation. It also includes wind tunnel test results and roughness testing.

Butterfield, C.P.; Musial, W.P.; Simms, D.A.

1992-10-01T23:59:59.000Z

8

Study of Composite Materials Application for Horizontal Axis Wind ...  

Science Conference Proceedings (OSTI)

Since the specific velocity is directly related to the coefficient of power Cp of a wind rotor, this article presents a comparative study with different materials and ...

9

Theoretical and experimental power from large horizontal-axis wind turbines  

SciTech Connect

A method for calculating the output power from large horizontal-axis wind turbines is presented. Modifications to the airfoil characteristics and the momentum portion of classical blade element-momentum theory are given that improve correlation with measured data. Improvement is particularly evident at low tip speed ratios where aerodynamic stall can occur as the blade experiences high angles of attack. Output power calculated using the modified theory is compared with measured data for several large wind turbines. These wind turbines range in size from the DOE/NASA 100 kW Mod-O (38 m rotor diameter) to the 2000 kW Mod-1 (61 m rotor diameter). The calculated results are in good agreement with measured data from these machines.

Viterna, L A; Janetzke, D C

1982-09-01T23:59:59.000Z

10

Structural effects of unsteady aerodynamic forces on horizontal-axis wind turbines  

DOE Green Energy (OSTI)

Due to its renewable nature and abundant resources, wind energy has the potential to fulfill a large portion of this nation`s energy needs. The simplest means of utilizing wind energy is through the use of downwind, horizontal-axis wind turbines (HAWT) with fixed-pitch rotors. This configuration regulates the peak power by allowing the rotor blade to aerodynamically stall. The stall point, the point of maximum coefficient of lift, is currently predicted using data obtained from wind tunnel tests. Unfortunately, these tests do not accurately simulate conditions encountered in the field. Flow around the tower and nacelle coupled with inflow turbulence and rotation of the turbine blades create unpredicted aerodynamic forces. Dynamic stall is hypothesized to occur. Such aerodynamic loads are transmitted into the rotor and tower causing structural resonance that drastically reduces the design lifetime of the wind turbine. The current method of alleviating this problem is to structurally reinforce the tower and blades. However, this adds unneeded mass and, therefore, cost to the turbines. A better understanding of the aerodynamic forces and the manner in which they affect the structure would allow for the design of more cost effective and durable wind turbines. Data compiled by the National Renewable Energy Laboratory (NREL) for a downwind HAWT with constant chord, untwisted, fixed-pitch rotors is analyzed. From these data, the actual aerodynamic characteristics of the rotor are being portrayed and the potential effects upon the structure can for the first time be fully analyzed. Based upon their understanding, solutions to the problem of structural resonance are emerging.

Miller, M.S.; Shipley, D.E. [Univ. of Colorado, Boulder, CO (United States). BioServe Space Technologies

1994-08-01T23:59:59.000Z

11

Horizontal-axis wind-system rotor performance model comparison: a compendium  

SciTech Connect

This compendium consists of four reports, the purpose of which is to evaluate performance prediction methods for horizontal-axis wind turbines. The reports were prepared by four separate contractors. Oregon State University, AeroVironment, Inc., Aerospace Systems, Inc., and United Technologies Research Center (UTRC). Three of the four contractors used a blade-element/momentum analysis, while the fourth (UTRC) utilized a lifting line/prescribed wake analysis. These contractors were to apply their prediction methods to two rotors, that of the Enertech 1500 and that of the 1/3-scale UTRC 8 kW turbines. Results from the four prediction methods are compared with actual test data gathered via Controlled Velocity Testing (CVT), carried out by the Rocky Flats Wind Energy Research Center, operated by Rockwell International for the US Department of Energy. The conclusions of the four reports are reviewed in an introduction prepared by Rockwell International. For the Enertech 1500, rotor performance predictions closely agreed with CVT data. Yet, because of the lack of high tip speed ratio data, verification of the Glauert momentum theory was not possible. Predictions regarding the UTRC 1/3 scale 8 kW rotor did not agree well with test results. The reasons cited for the discrepancies center on inadequate airfoil section data and the varying blade pitch angles of the unique UTRC flexbeam rotor.

Not Available

1983-02-01T23:59:59.000Z

12

Lidar Measurement of Turbulence Encountered by Horizontal-Axis Wind Turbines  

Science Conference Proceedings (OSTI)

We used a continuous-wave (CW) Doppler lidar to measure wind velocity turbulence from a moving frame of reference. By directing the lidar beam to trace the perimeters of vertical-plane disks about horizontal axes parallel to the mean wind ...

R. M. Hardesty; B. F. Weber

1987-03-01T23:59:59.000Z

13

A study of pitch oscillation and roughness on airfoils used for horizontal axis wind turbines  

DOE Green Energy (OSTI)

Under subcontract XF-1-11009-3 the Ohio State University Aeronautical and Astronautical Research Laboratory (OSU/AARL) with the National Renewable Energy Laboratory (NREL) developed an extensive database of empirical aerodynamic data. These data will assist in the development of analytical models and in the design of new airfoils for wind turbines. To accomplish the main objective, airfoil models were designed, built and wind tunnel tested with and without model leading edge grit roughness (LEGR). LEGR simulates surface irregularities due to the accumulation of insect debris, ice, and/or the aging process. This report is a summary of project project activity for Phase III, which encompasses the time period from September 17, 1 993 to September 6, 1 994.

Gregorek, G.M.; Hoffmann, M.J.; Ramsay, R.R.; Janiszewska, J.M. [Ohio State Univ., Columbus, OH (United States)

1995-12-01T23:59:59.000Z

14

Analysis and test results for a two-bladed, passive cycle pitch, horizontal-axis wind turbine in free and controlled yaw  

SciTech Connect

This report surveys the analysis and tests performed at Washington University in St. Louis, Missouri, on a horizontal-axis, two-laded wind turbine with teeter hub. The introduction is a brief account of results obtained during the 5-year period ending December 1985. The wind tunnel model and the test turbine (7.6 m [25 ft.] in diameter) at Washington University`s Tyson Research Center had a 67{degree} delta-three angle of the teeter axis. The introduction explains why this configuration was selected and named the passive cycle pitch (PCP) wind turbine. Through the analysis was not limited to the PCP rotor, all tests, including those done from 1986 to 1994, wee conducted with the same teetered wind rotor. The blades are rather stiff and have only a small elastic coning angle and no precone.

Holenemser, K.H. [Washington Univ., St. Louis, MO (United States)

1995-10-01T23:59:59.000Z

15

ARM - Measurement - Horizontal wind  

NLE Websites -- All DOE Office Websites (Extended Search)

govMeasurementsHorizontal wind govMeasurementsHorizontal wind ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Measurement : Horizontal wind The horizontal wind in terms of either speed and direction, or the zonal (u) and meridional (v) components. Categories Atmospheric State Instruments The above measurement is considered scientifically relevant for the following instruments. Refer to the datastream (netcdf) file headers of each instrument for a list of all available measurements, including those recorded for diagnostic or quality assurance purposes. ARM Instruments SONDE : Balloon-Borne Sounding System CO2FLX : Carbon Dioxide Flux Measurement Systems ECOR : Eddy Correlation Flux Measurement System DISDROMETER : Impact Disdrometer

16

Vertical axis wind turbines  

DOE Patents (OSTI)

A vertical axis wind turbine is described. The wind turbine can include a top ring, a middle ring and a lower ring, wherein a plurality of vertical airfoils are disposed between the rings. For example, three vertical airfoils can be attached between the upper ring and the middle ring. In addition, three more vertical airfoils can be attached between the lower ring and the middle ring. When wind contacts the vertically arranged airfoils the rings begin to spin. By connecting the rings to a center pole which spins an alternator, electricity can be generated from wind.

Krivcov, Vladimir (Miass, RU); Krivospitski, Vladimir (Miass, RU); Maksimov, Vasili (Miass, RU); Halstead, Richard (Rohnert Park, CA); Grahov, Jurij (Miass, RU)

2011-03-08T23:59:59.000Z

17

Investigating the Influence of the Added Mass Effect to Marine Hydrokinetic Horizontal-Axis Turbines Using a General Dynamic Wake Wind Turbine Code  

DOE Green Energy (OSTI)

This paper describes a recent study to investigate the applicability of a horizontal-axis wind turbine (HAWT) structural dynamics and unsteady aerodynamics analysis program (FAST and AeroDyn respectively) to modeling the forces on marine hydrokinetic (MHK) turbines. This paper summarizes the added mass model that has been added to AeroDyn. The added mass model only includes flow acceleration perpendicular to the rotor disc, and ignores added mass forces caused by blade deflection. A model of the National Renewable Energy Laboratory's (NREL) Unsteady Aerodynamics Experiment (UAE) Phase VI wind turbine was analyzed using FAST and AeroDyn with sea water conditions and the new added mass model. The results of this analysis exhibited a 3.6% change in thrust for a rapid pitch case and a slight change in amplitude and phase of thrust for a case with 30{sup o} of yaw.

Maniaci, D. C.; Li, Y.

2011-10-01T23:59:59.000Z

18

Investigating the Influence of the Added Mass Effect to Marine Hydrokinetic Horizontal-Axis Turbines Using a General Dynamic Wake Wind Turbine Code: Preprint  

DOE Green Energy (OSTI)

This paper describes a recent study to investigate the applicability of a horizontal-axis wind turbine (HAWT) structural dynamics and unsteady aerodynamics analysis program (FAST and AeroDyn respectively) to modeling the forces on marine hydrokinetic (MHK) turbines. It summarizes the added mass model that has been added to AeroDyn. The added mass model only includes flow acceleration perpendicular to the rotor disc, and ignores added mass forces caused by blade deflection. A model of the National Renewable Energy Laboratory's (NREL) Unsteady Aerodynamics Experiment (UAE) Phase VI wind turbine was analyzed using FAST and AeroDyn with sea water conditions and the new added mass model. The results of this analysis exhibited a 3.6% change in thrust for a rapid pitch case and a slight change in amplitude and phase of thrust for a case with 30 degrees of yaw.

Maniaci, D. C.; Li, Y.

2012-04-01T23:59:59.000Z

19

A comparison of spanwise aerodynamic loads estimated from measured bending moments versus direct pressure measurements on horizontal axis wind turbine blades  

DOE Green Energy (OSTI)

Two methods can be used to determine aerodynamic loads on a rotating wind turbine blade. The first is to make direct pressure measurements on the blade surface. This is a difficult process requiring costly pressure instrumentation. The second method uses measured flap bending moments in conjunction with analytical techniques to estimate airloads. This method, called ALEST, was originally developed for use on helicopter rotors and was modified for use on horizontal axis wind turbine blades. Estimating airloads using flap bending moments in much simpler and less costly because measurements can be made with conventional strain gages and equipment. This paper presents results of airload estimates obtained using both methods under a variety of operating conditions. Insights on the limitations and usefulness of the ALEST bending moment technique are also included. 10 refs., 6 figs.

Simms, D A; Butterfield, C P

1991-10-01T23:59:59.000Z

20

Marketing Strategies for Horizontal Axis Washers  

Science Conference Proceedings (OSTI)

Horizontal axis washing machines provide superior washing quality and gentleness as well as reduced energy use. This EPRI guide describes how utilities can effectively engage the horizontal axis washing machine market and the strategic and load-related reasons they should be interested in doing so. The guide covers topics ranging from a detailed overview of the marketplace to specific tactical advice that offers practical insights for any utility considering entering this new market.

1997-04-21T23:59:59.000Z

Note: This page contains sample records for the topic "horizontal axis wind" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Investigating the Influence of the Added Mass Effect to Marine Hydrokinetic Horizontal-Axis Turbines Using a General Dynamic Wake Wind Turbine Code  

NLE Websites -- All DOE Office Websites (Extended Search)

Investigating the Influence of Investigating the Influence of the Added Mass Effect to Marine Hydrokinetic Horizontal-Axis Turbines Using a General Dynamic Wake Wind Turbine Code D.C. Maniaci Pennsylvania State University Y. Li National Renewable Energy Laboratory Presented at the Oceans 11 Conference Kona, Hawaii September 19-21, 2011 Conference Paper NREL/CP-5000-52306 October 2011 NOTICE The submitted manuscript has been offered by an employee of the Alliance for Sustainable Energy, LLC (Alliance), a contractor of the US Government under Contract No. DE-AC36-08GO28308. Accordingly, the US Government and Alliance retain a nonexclusive royalty-free license to publish or reproduce the published form of this contribution, or allow others to do so, for US Government purposes.

22

Modelling the aerodynamics of vertical-axis wind turbines.  

E-Print Network (OSTI)

??The current generation of wind turbines that are being deployed around the world features, almost exclusively, a three-bladed rotor with a horizontal-axis configuration. In recent… (more)

Scheurich, Frank

2011-01-01T23:59:59.000Z

23

Vertical axis wind turbine airfoil  

DOE Patents (OSTI)

A vertical axis wind turbine airfoil is described. The wind turbine airfoil can include a leading edge, a trailing edge, an upper curved surface, a lower curved surface, and a centerline running between the upper surface and the lower surface and from the leading edge to the trailing edge. The airfoil can be configured so that the distance between the centerline and the upper surface is the same as the distance between the centerline and the lower surface at all points along the length of the airfoil. A plurality of such airfoils can be included in a vertical axis wind turbine. These airfoils can be vertically disposed and can rotate about a vertical axis.

Krivcov, Vladimir; Krivospitski, Vladimir; Maksimov, Vasili; Halstead, Richard; Grahov, Jurij Vasiljevich

2012-12-18T23:59:59.000Z

24

Vertical-axis wind turbines -- The current status of an old technology  

DOE Green Energy (OSTI)

Vertical-axis wind turbine technology is not well understood, even though the earliest wind machines rotated about a vertical axis. The operating environment of a vertical-axis wind turbine is quite complex, but detailed analysis capabilities have been developed and verified over the last 30 years. Although vertical-axis technology has not been widely commercialized, it exhibits both advantages and disadvantages compared to horizontal-axis technology, and in some applications, it appears to offer significant advantages.

Berg, D.E.

1996-12-31T23:59:59.000Z

25

Horizontal-axis clothes washer market poised for expansion  

SciTech Connect

The availability of energy- and water-efficient horizontal-axis washing machines in the North American market is growing, as US and European manufacturers position for an expected long-term market shift toward horizontal-axis (H-axis) technology. Four of the five major producers of washing machines in the US are developing or considering new H-axis models. New entrants, including US-based Staber Industries and several European manufacturers, are also expected to compete in this market. The intensified interest in H-axis technology is partly driven by speculation that new US energy efficiency standards, to be proposed in 1996 and implemented in 1999, will effectively mandate H-axis machines. H-axis washers typically use one-third to two-thirds less energy, water, and detergent than vertical-axis machines. Some models also reduce the energy needed to dry the laundry, since their higher spin speeds extract more water than is typical with vertical-axis designs. H-axis washing machines are the focus of two broadly-based efforts to support coordinated research and incentive programs by electric, gas, and water utilities: The High-Efficiency Laundry Metering/Marketing Analysis (THELMA), and the Consortium for Energy Efficiency (CEE) High-Efficiency Clothes Washer Initiative. These efforts may help to pave the way for new types of marketing partnerships among utilities and other parties that could help to speed adoption of H-axis washers.

George, K.L.

1994-12-31T23:59:59.000Z

26

MHK Technologies/Horizontal Axis Logarithmic Spiral Turbine | Open Energy  

Open Energy Info (EERE)

Horizontal Axis Logarithmic Spiral Turbine Horizontal Axis Logarithmic Spiral Turbine < MHK Technologies Jump to: navigation, search << Return to the MHK database homepage Technology Profile Primary Organization Golden Turbines LLC Technology Resource Click here Current Technology Type Click here Axial Flow Turbine Technology Readiness Level Click here TRL 1 3 Discovery Concept Def Early Stage Dev Design Engineering Technology Description A Horizontal axis Water turbine following the logarithmic spiral to generate clean electric energy from slow moving currents like rivers or ocean currents and with least impact on marine life and the environment because it doesn t require a damn or building huge structures Technology Dimensions Device Testing Date Submitted 36:09.5 << Return to the MHK database homepage

27

Vertical Axis Wind Turbine Foundation parameter study  

DOE Green Energy (OSTI)

The dynamic failure criterion governing the dimensions of prototype Vertical Axis Wind Turbine Foundations is treated as a variable parameter. The resulting change in foundation dimensions and costs is examined.

Lodde, P.F.

1980-07-01T23:59:59.000Z

28

A low order model for vertical axis wind turbines  

E-Print Network (OSTI)

A new computational model for initial sizing and performance prediction of vertical axis wind turbines

Drela, Mark

29

Simulation of winds as seen by a rotating vertical axis wind turbine blade  

DOE Green Energy (OSTI)

The objective of this report is to provide turbulent wind analyses relevant to the design and testing of Vertical Axis Wind Turbines (VAWT). A technique was developed for utilizing high-speed turbulence wind data from a line of seven anemometers at a single level to simulate the wind seen by a rotating VAWT blade. Twelve data cases, representing a range of wind speeds and stability classes, were selected from the large volume of data available from the Clayton, New Mexico, Vertical Plane Array (VPA) project. Simulations were run of the rotationally sampled wind speed relative to the earth, as well as the tangential and radial wind speeds, which are relative to the rotating wind turbine blade. Spectral analysis is used to compare and assess wind simulations from the different wind regimes, as well as from alternate wind measurement techniques. The variance in the wind speed at frequencies at or above the blade rotation rate is computed for all cases, and is used to quantitatively compare the VAWT simulations with Horizontal Axis Wind Turbine (HAWT) simulations. Qualitative comparisons are also made with direct wind measurements from a VAWT blade.

George, R.L.

1984-02-01T23:59:59.000Z

30

Estimators for the Standard Deviation of Horizontal Wind Direction  

Science Conference Proceedings (OSTI)

The standard deviation of horizontal wind direction is a central quantity in the description of atmospheric turbulence and of great practical use in dispersion models. As horizontal wind direction is a circular variable, its standard deviation ...

Rudolf O. Weber

1997-10-01T23:59:59.000Z

31

Vertical axis wind turbine control strategy  

DOE Green Energy (OSTI)

Early expensive in automatic operation of the Sandia 17-m vertical axis research wind turbine (VAWT) has demonstrated the need for a systematic study of control algorithms. To this end, a computer model has been developed that uses actual wind time series and turbine performance data to calculate the power produced by the Sandia 17-m VAWT operating in automatic control. The model has been used to investigate the influence of starting algorithms on annual energy production. The results indicate that, depending on turbine and local wind characteristics, a bad choice of a control algorithm can significantly reduce overall energy production. The model can be used to select control algorithms and threshold parameters that maximize long-term energy production. An attempt has been made to generalize these results from local site and turbine characteristics to obtain general guidelines for control algorithm design.

McNerney, G.M.

1981-08-01T23:59:59.000Z

32

Vertical axis wind turbine with continuous blade angle adjustment  

E-Print Network (OSTI)

The author presents a concept for a vertical axis wind turbine that utilizes each blade's entire rotational cycle for power generation. Each blade has its own vertical axis of rotation and is constrained to rotate at the ...

Weiss, Samuel Bruce

2010-01-01T23:59:59.000Z

33

Airfoil treatments for vertical axis wind turbines  

SciTech Connect

Sandia National Laboratories (SNL) has taken three airfoil related approaches to decreasing the cost of energy of vertical axis wind turbine (VAWT) systems; airfoil sections designed specifically for VAWTs, vortex generators (VGs), and ''pumped spoiling.'' SNL's blade element airfoil section design effort has led to three promising natural laminar flow (NLF) sections. One section is presently being run on the SNL 17-m turbine. Increases in peak efficiency and more desirable dynamic stall regulation characteristics have been observed. Vane-type VGs were fitted on one DOE/Alcoa 100 kW VAWT. With approximately 12% of span having VGs, annual energy production increased by 5%. Pumped spoiling utilizes the centrifugal pumping capabilities of hollow blades. With the addition of small perforations in the surface of the blades and valves controlled by windspeed at the ends of each blade, lift spoiling jets may be generated inducing premature stall and permitting lower capacity, lower cost drivetrain components. SNL has demonstrated this concept on its 5-m turbine and has wind tunnel tested perforation geometries on one NLF section.

Klimas, P.C.

1985-01-01T23:59:59.000Z

34

Means and Standard Deviations of Horizontal Wind Components  

Science Conference Proceedings (OSTI)

An algorithm is presented that computes a measure of horizontal wind dispersion. The algorithm features a compact, machine economic structure that removes wind direction scale discontinuities. By requiring only one pass through the input data, ...

G. R. Ackermann

1983-05-01T23:59:59.000Z

35

Response of a Vertical Axis Wind Turbine to Time Varying Wind Conditions found within the Urban  

E-Print Network (OSTI)

Response of a Vertical Axis Wind Turbine to Time Varying Wind Conditions found within the Urban, 2010 PP 389­401 389 ABSTRACT Experimental testing of a vertical axis wind turbine within the urban of the turbine. Temporal variation of the wind with respect to the direction and velocity fluctuations

Tullis, Stephen

36

Wind Turbines  

Energy.gov (U.S. Department of Energy (DOE))

Although all wind turbines operate on similar principles, several varieties are in use today. These include horizontal axis turbines and vertical axis turbines.

37

Helical-axis stellarator with helical windings  

SciTech Connect

The equilibrium and stability of the plasma in a stellarator with a helical geometric axis and with helical external fields are analyzed.

Mikhailov, M.I.; Pustovitov, V.D.

1981-10-05T23:59:59.000Z

38

Horizontal-axis washing machines offer large savings: New models entering North American market  

Science Conference Proceedings (OSTI)

Long popular in Europe, new horizontal-axis clothes washers are entering the North American market, creating opportunities for government and utility conservation efforts. Unlike vertical-axis machines, which immerse the clothes in water, horizontal-axis designs use a tumbling action and require far less water, water-heating energy, and detergent. One development in this area is the recent reintroduction by the Frigidaire Company of a full-size, front-load, horizontal-axis washing machine. The new model is an improved version of an earlier design that was discontinued in mid-1991 during changes in manufacturing facilities. It is available under the Sears Kenmore, White-Westinghouse, and Gibson labels. While several European and commercial-grade front-load washers are sold in the US, they are all considerably more expensive than the Frigidaire machine, making it the most efficient clothes washer currently available in a mainstream North American consumer product line.

Shepard, M.

1992-12-31T23:59:59.000Z

39

Fish schooling as a basis for vertical axis wind turbine farm design  

E-Print Network (OSTI)

Most wind farms consist of horizontal axis wind turbines (HAWTs) due to the high power coefficient (mechanical power output divided by the power of the free-stream air through the turbine cross-sectional area) of an isolated turbine. However when in close proximity to neighbouring turbines, HAWTs suffer from a reduced power coefficient. In contrast, previous research on vertical axis wind turbines (VAWTs) suggests that closely-spaced VAWTs may experience only small decreases (or even increases) in an individual turbine's power coefficient when placed in close proximity to neighbours, thus yielding much higher power outputs for a given area of land. A potential flow model of inter-VAWT interactions is developed to investigate the effect of changes in VAWT spatial arrangement on the array performance coefficient, which compares the expected average power coefficient of turbines in an array to a spatially-isolated turbine. A geometric arrangement based on the configuration of shed vortices in the wake of schooli...

Whittlesey, Robert W; Dabiri, John O

2010-01-01T23:59:59.000Z

40

IntroductionIntroduction The use of small scale vertical axis wind turbinesThe use of small scale vertical axis wind turbines  

E-Print Network (OSTI)

IntroductionIntroduction The use of small scale vertical axis wind turbinesThe use of small scale vertical axis wind turbines (VAWT) is being studied at McMaster University using(VAWT) is being studied

Tullis, Stephen

Note: This page contains sample records for the topic "horizontal axis wind" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

UNSTEADY SIMULATION OF FLOW IN MICRO VERTICAL AXIS WIND TURBINE  

E-Print Network (OSTI)

Though wind turbines and windmills have been used for centuries, the application of aerodynamics technology to improve reliability and reduce costs of wind-generated energy has only been pursued in earnest for the past 40 years. Today, wind energy is mainly used to generate electricity. Wind is a renewable energy source. Power production from wind turbines is affected by certain conditions: wind speed, turbine speed, turbulence and the changes of wind direction. These conditions are not always optimal and have negative effects on most turbines. The present turbine is supposed to be less affected by these conditions because the blades combine a rotating movement around each own axis and around the nacelle’s one. Due to this combination of movements, flow around this turbine can be more highly unsteady, because of great blade stagger angles. The turbine has a rotor with three straight blades of symmetrical airfoil. Paper presents unsteady simulations that have been performed for one wind velocity, and different initial blades stagger angles. The influence of interaction of blades is studied for one specific constant rotational speed among the four rotational speeds that have been studied.

A. C. Bayeul-lainé; G. Bois

2013-01-01T23:59:59.000Z

42

ANL/APS/TB-32 Test of Horizontal Field Measurements Using Two-Axis Hall  

NLE Websites -- All DOE Office Websites (Extended Search)

2 2 Test of Horizontal Field Measurements Using Two-Axis Hall Probes at the APS Magnetic Measurement Facility I. Vasserman Advanced Photon Source Argonne National Laboratory Argonne, IL 60439 1. Introduction The free-electron laser (FEL) project at the Advanced Photon Source (APS) will use a 400-MeV particle beam from the APS linac with RMS beam transverse size of 100 µm and requires very high performance of the insertion devices in order to achieve high intensity radiation. Averaged over period, the trajectory must deviate from the ideal on-axis trajectory by not more than 10% of the RMS beam size. Meaning that the second field integral should be straight within ±1300 G-cm 2 over the length of the device for both horizontal and vertical directions for the 400-MeV particle

43

Torque ripple in a Darrieus, vertical axis wind turbine  

DOE Green Energy (OSTI)

Interaction between a steady wind and a rotating, Darrieus, vertical axis wind turbine produces time periodic aerodynamic loads which cause time dependent torque variations, referred to as torque ripple, to occur in the mechanical link between the turbine and the electrical generator. There is concern for the effect of torque ripple upon fatigue life of drive train components and upon power quality. An analytical solution characterizing the phenomenon of torque ripple has been obtained which is based upon a Fourier expansion of the time dependent features of the problem. Numerical results for torque ripple, some experimental data, determination of acceptable levels and methods of controlling it, are presented and discussed.

Reuter, R.C. Jr.

1980-01-01T23:59:59.000Z

44

Wind Synthesis and Quality Control of Multiple-Doppler-Derived Horizontal Wind Fields  

Science Conference Proceedings (OSTI)

Horizontal wind vector fields can be measured in real time by a bistatic Doppler radar network and can be applied directly for hazard warnings and weather surveillance. Most applications, however, especially for meteorological research and ...

Katja Friedrich; Martin Hagen

2004-01-01T23:59:59.000Z

45

WIND-TUNNEL STUDY ON AERODYNAMIC PERFORMANCE OF SMALL VERTICAL-AXIS WIND TURBINES  

E-Print Network (OSTI)

of a building was explored [2]. Referred to such applications, a VAWT can be so small in physical size that its by the present authors to study the aerodynamic performance of small VAWTs using the experimental and numerical1 WIND-TUNNEL STUDY ON AERODYNAMIC PERFORMANCE OF SMALL VERTICAL-AXIS WIND TURBINES J. J. Miau*1

Leu, Tzong-Shyng "Jeremy"

46

Blade Offset and Pitch Effects on a High Solidity Vertical Axis Wind Turbine  

E-Print Network (OSTI)

ABSTRACT A high solidity, small scale, 2.5m diameter by 3m high Vertical Axis Wind Turbine (VAWT, performance 1. INTRODUCTION Small scale vertical axis wind turbines (VAWTs) show potential for urban rooftop turbines. Keywords: Vertical Axis Wind Turbine, VAWT, airfoil, pitch, blade, mount, offset, high solidity

Tullis, Stephen

47

Performance Testing of a Small Vertical-Axis Wind Turbine , S. Tullis2  

E-Print Network (OSTI)

Performance Testing of a Small Vertical-Axis Wind Turbine R. Bravo1 , S. Tullis2 , S. Ziada3 of electric production [1]. Although most performance testing for small-scale wind turbines is conducted vertical-axis wind turbines (VAWT) in urban settings, full-scale wind tunnel testing of a prototype 3.5 k

Tullis, Stephen

48

Retrieving Horizontal Temperature Gradients and Advections from Single-Station Wind Profiler Observations  

Science Conference Proceedings (OSTI)

Vertical wind shears measured by the Plattevilie, Colorado wind profiler were used in conjunction with the geostrophic thermal wind equation to retrieve the horizontal thermal gradients and associated advections for a case involving an upper-...

Paul J. Neiman; M. A. Shapiro

1989-06-01T23:59:59.000Z

49

Mesh Requirement Investigation for 2D and 3D Aerodynamic Simulation of Vertical Axis Wind Turbines.  

E-Print Network (OSTI)

??The accuracy of a Computational Fluid Dynamics (CFD) model to capture the complex flow around a small vertical axis wind turbine (VAWT) on 2D and… (more)

Naghib Zadeh, Saman

2013-01-01T23:59:59.000Z

50

A Horizontal Wind and Wind Confidence Algorithm for Doppler Wind Profilers  

Science Conference Proceedings (OSTI)

Boundary layer wind profilers are increasingly being used in applications that require high-quality, rapidly updated winds. An example of this type of application is an airport wind hazard warning system. Wind shear can be a hazard to flight ...

Robert K. Goodrich; Corrinne S. Morse; Larry B. Cornman; Stephen A. Cohn

2002-03-01T23:59:59.000Z

51

A New Approach for the Determination of Horizontal Wind Direction Fluctuations  

Science Conference Proceedings (OSTI)

A new method to determine horizontal wind direction fluctuations ?? is presented based on the hypothesis of a Gaussian distribution of wind direction that gradually moves to a circular, uniform distribution under near-clam conditions. A ...

J. I. Ibarra

1995-09-01T23:59:59.000Z

52

Innovative wind turbines. Circulation controlled vertical axis wind turbine. Progress report, March 1-December 31, 1976  

DOE Green Energy (OSTI)

Theoretical and experimental research efforts in evaluating an innovative concept for vertical axis wind turbines (VAWT) are described. The concept is that of using straight blades composed of circulation controlled airfoil sections. The theoretical analysis has been developed to determine the unsteady lift and moment characteristics of multiple-blade cross-flow wind turbines. To determine the drag data needed as input to the theoretical analysis, an outdoor test model VAWT has been constructed; design details, instrumentation, and calibration results are reported. Initial testing is with fixed pitch blades having cross-sections of conventional symmetrical airfoils. Costs of building the test model are included, as well as estimates for blades constructed with composite materials. These costs are compared with those of other types of wind turbines.

Walters, R. E.; Fanucci, J. B.; Hill, P. W.; Migliore, P. G.; Squire, W.; Waltz, T. L.

1978-10-01T23:59:59.000Z

53

Blade shape for a tropskien type of vertical-axis wind turbine  

SciTech Connect

The equations derived to define a troposkien (the shape a completely flexible cable assumes when it is spun at a constant angular velocity about a vertical axis to which its two ends are attached) are described. The implications of the solutions on the design of a vertical-axis wind turbine are discussed for cases where gravity is neglected.

Blackwell, B.F.; Reis, G.E.

1977-03-01T23:59:59.000Z

54

The Relationships among Wind, Horizontal Pressure Gradient, and Turbulent Momentum Transport during CASES-99  

Science Conference Proceedings (OSTI)

Relationships among the horizontal pressure gradient, the Coriolis force, and the vertical momentum transport by turbulent fluxes are investigated using data collected from the Cooperative Atmosphere-Surface Exchange Study in 1999 (CASES99). Wind ...

Jielun Sun; Donald H. Lenschow; Larry Mahrt; Carmen Nappo

55

Wind Turbine Basics | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Wind Turbine Basics Wind Turbine Basics Wind Turbine Basics July 30, 2013 - 2:58pm Addthis Energy 101: Wind Turbines Basics This video explains the basics of how wind turbines operate to produce clean power from an abundant, renewable resource-the wind. Text Version Wind turbine assembly Although all wind turbines operate on similar principles, several varieties are in use today. These include horizontal axis turbines and vertical axis turbines. Horizontal Axis Turbines Horizontal axis turbines are the most common turbine configuration used today. They consist of a tall tower, atop which sits a fan-like rotor that faces into or away from the wind, a generator, a controller, and other components. Most horizontal axis turbines built today are two- or three-bladed. Horizontal axis turbines sit high atop towers to take advantage of the

56

Vertical axis wind turbine development. Executive summary. Final report, March 1, 1976-June 30, 1977  

DOE Green Energy (OSTI)

Information is presented concerning the numerical solution of the aerodynamics of cross-flow wind turbines; boundary layer considerations for a vertical axis wind turbine; WVU VAWT outdoor test model; low solidity blade tests; high solidity blade design; cost analysis of the WVU VAWT test model; structural parametric analysis of VAWT blades; and cost study of current WECS.

Walters, R. E.; Fanucci, J. B.; Hill, P. W.; Migliore, P. G.

1979-07-01T23:59:59.000Z

57

Order-of-magnitude enhancement of wind farm power density via counter-rotating vertical-axis wind turbine arrays  

E-Print Network (OSTI)

Modern wind farms require significant land resources to separate each wind turbine from the adjacent turbine wakes. These aerodynamic constraints limit the amount of power that can be extracted from a given wind farm footprint. We conducted full-scale field tests of vertical-axis wind turbines in counter-rotating configurations under natural wind conditions. Whereas wind farms consisting of propeller-style turbines produce 2 to 3 watts of power per square meter of land area, these field tests indicate that power densities approaching 100 W m^-2 can be achieved by arranging vertical-axis wind turbines in layouts that enable them to extract energy from adjacent wakes. In addition, we calculated that the global wind resource available to 10-m tall turbines based on the present approach is approximately 225 trillion watts (TW), which significantly exceeds the global wind resource available to 80-m tall, propeller-style wind turbines, approximately 75 TW. This improvement is due to the closer spacing that can be a...

Dabiri, John O

2010-01-01T23:59:59.000Z

58

Does Increased Horizontal Resolution Improve Hurricane Wind Forecasts?  

Science Conference Proceedings (OSTI)

The representation of tropical cyclone track, intensity, and structure in a set of 69 parallel forecasts performed at each of two horizontal grid increments with the Advanced Research Hurricane (AHW) component of the Weather and Research and ...

Christopher Davis; Wei Wang; Jimy Dudhia; Ryan Torn

2010-12-01T23:59:59.000Z

59

Energy Basics: Wind Turbines  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Photo of a crane lifting the blades onto a wind turbine that reads 'U.S. Department of Energy, NREL.' You can learn more about horizontal axis turbines from the EERE Wind Program's...

60

Wind turbine | Open Energy Information  

Open Energy Info (EERE)

turbine turbine Jump to: navigation, search Dictionary.png Wind turbine: A machine that converts wind energy to mechanical energy; typically connected to a generator to produce electricity. Other definitions:Wikipedia Reegle Contents 1 Types of Wind Turbines 1.1 Vertical Axis Wind Turbines 1.2 Horizontal Axis Wind Turbines 2 Wind Turbine Sizes 3 Components of a Wind Turbine 4 References Types of Wind Turbines There are two basic wind turbine designs: those with a vertical axis (sometimes referred to as VAWTs) and those with a horizontal axis (sometimes referred to as HAWTs). There are several manufacturers of vertical axis turbines, but they have not penetrated the "utility scale" (100 kW capacity and larger) market to the same degree as horizontal axis turbines.[1]

Note: This page contains sample records for the topic "horizontal axis wind" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Wind Turbine Basics | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Turbine Basics Turbine Basics Wind Turbine Basics July 30, 2013 - 2:58pm Addthis Energy 101: Wind Turbines Basics This video explains the basics of how wind turbines operate to produce clean power from an abundant, renewable resource-the wind. Text Version Wind turbine assembly Although all wind turbines operate on similar principles, several varieties are in use today. These include horizontal axis turbines and vertical axis turbines. Horizontal Axis Turbines Horizontal axis turbines are the most common turbine configuration used today. They consist of a tall tower, atop which sits a fan-like rotor that faces into or away from the wind, a generator, a controller, and other components. Most horizontal axis turbines built today are two- or three-bladed. Horizontal axis turbines sit high atop towers to take advantage of the

62

The Economic Optimization of Wind Turbine Design .  

E-Print Network (OSTI)

??This thesis studies the optimization of a variable speed, three blade, horizontal-axis wind turbine. The design parameters considered are the rotor diameter, hub height and… (more)

Schmidt, Michael Frank

2007-01-01T23:59:59.000Z

63

Sandia Vertical-Axis Wind Turbine Program. Technical quarterly report, July--September 1976. [USA  

DOE Green Energy (OSTI)

This quarterly report describes the activities of the Sandia Laboratories' Vertical-Axis Wind Turbine (VAWT) project during the period July to September 1976, transitional quarter of fiscal year 1976. Included are the highlights of the quarter; review of the status of general design efforts in the areas of aerodynamics, structures, and testing.

Grover, R.D.; Veneruso, A.F. (eds.)

1977-06-01T23:59:59.000Z

64

Test plan for the 34 meter vertical axis wind turbine test bed located at Bushland, Texas  

DOE Green Energy (OSTI)

A plan is presented for the testing and evaluation of a new 500 kw vertical axis wind turbine test bed. The plan starts with the initial measurements made during construction, proceeds through evaluation of the design, the development of control methods, and finally to the test bed phase where new concepts are evaluated and in-depth studies are performed.

Stephenson, W.A.

1986-12-01T23:59:59.000Z

65

Effects of blade configurations on flow distribution and power output of a Zephyr vertical axis wind turbine  

Science Conference Proceedings (OSTI)

Numerical simulations with FLUENT software were conducted to investigate the fluid flow through a novel vertical axis wind turbine (VAWT). Simulation of flow through the turbine rotor was performed with the aim of predicting the performance characteristics ... Keywords: blade configuration, power output, rotor, simulation, vertical axis wind turbine

J. O. Ajedegba; G. F. Naterer; M. A. Rosen; E. Tsang

2008-02-01T23:59:59.000Z

66

Development and Verification of a Computational Fluid Dynamics Model of a Horizontal-Axis Tidal Current Turbine  

NLE Websites -- All DOE Office Websites (Extended Search)

Development and Verification of Development and Verification of a Computational Fluid Dynamics Model of a Horizontal-Axis Tidal Current Turbine M.J. Lawson and Y. Li. National Renewable Energy Laboratory D.C. Sale University of Washington Presented at the 30 th International Conference on Ocean, Offshore, and Arctic Engineering Rotterdam, The Netherlands June 19-24, 2011 NREL is a national laboratory of the U.S. Department of Energy, Office of Energy Efficiency & Renewable Energy, operated by the Alliance for Sustainable Energy, LLC. Conference Paper NREL/CP-5000-50981 October 2011 Contract No. DE-AC36-08GO28308 NOTICE The submitted manuscript has been offered by an employee of the Alliance for Sustainable Energy, LLC (Alliance), a contractor of the US Government under Contract No. DE-AC36-08GO28308. Accordingly, the US

67

Development and Verification of a Computational Fluid Dynamics Model of a Horizontal-Axis Tidal Current Turbine  

DOE Green Energy (OSTI)

This paper describes the development of a computational fluid dynamics (CFD) methodology to simulate the hydrodynamics of horizontal-axis tidal current turbines. Qualitative measures of the CFD solutions were independent of the grid resolution. Conversely, quantitative comparisons of the results indicated that the use of coarse computational grids results in an under prediction of the hydrodynamic forces on the turbine blade in comparison to the forces predicted using more resolved grids. For the turbine operating conditions considered in this study, the effect of the computational timestep on the CFD solution was found to be minimal, and the results from steady and transient simulations were in good agreement. Additionally, the CFD results were compared to corresponding blade element momentum method calculations and reasonable agreement was shown. Nevertheless, we expect that for other turbine operating conditions, where the flow over the blade is separated, transient simulations will be required.

Lawson, M. J.; Li, Y.; Sale, D. C.

2011-10-01T23:59:59.000Z

68

Structural Design of a Horizontal-Axis Tidal Current Turbine Composite Blade  

DOE Green Energy (OSTI)

This paper describes the structural design of a tidal composite blade. The structural design is preceded by two steps: hydrodynamic design and determination of extreme loads. The hydrodynamic design provides the chord and twist distributions along the blade length that result in optimal performance of the tidal turbine over its lifetime. The extreme loads, i.e. the extreme flap and edgewise loads that the blade would likely encounter over its lifetime, are associated with extreme tidal flow conditions and are obtained using a computational fluid dynamics (CFD) software. Given the blade external shape and the extreme loads, we use a laminate-theory-based structural design to determine the optimal layout of composite laminas such that the ultimate-strength and buckling-resistance criteria are satisfied at all points in the blade. The structural design approach allows for arbitrary specification of the chord, twist, and airfoil geometry along the blade and an arbitrary number of shear webs. In addition, certain fabrication criteria are imposed, for example, each composite laminate must be an integral multiple of its constituent ply thickness. In the present effort, the structural design uses only static extreme loads; dynamic-loads-based fatigue design will be addressed in the future. Following the blade design, we compute the distributed structural properties, i.e. flap stiffness, edgewise stiffness, torsion stiffness, mass, moments of inertia, elastic-axis offset, and center-of-mass offset along the blade. Such properties are required by hydro-elastic codes to model the tidal current turbine and to perform modal, stability, loads, and response analyses.

Bir, G. S.; Lawson, M. J.; Li, Y.

2011-10-01T23:59:59.000Z

69

The Influence of Unsteady Wind on the Performance and Aerodynamics of Vertical Axis Wind Turbines.  

E-Print Network (OSTI)

??Interest in small–scale wind turbines as energy sources in the built environment has increased due to the desire of consumers in urban areas to reduce… (more)

Danao, Louis Angelo

2012-01-01T23:59:59.000Z

70

Proceedings of the vertical axis wind turbine (VAWT) design technology seminar for industry  

Science Conference Proceedings (OSTI)

The objective of the Vertical Axis Wind Turbine (VAWT) Program at Sandia National Laboratories is to develop technology that results in economical, industry-produced, and commercially marketable wind energy systems. The purpose of the VAWT Design Technology Seminar or Industry was to provide for the exchange of the current state-of-the-art and predictions for future VAWT technology. Emphasis was placed on technology transfer on Sandia's technical developments and on defining the available analytic and design tools. Separate abstracts are included for presented papers.

Johnston, S.F. Jr. (ed.)

1980-08-01T23:59:59.000Z

71

United States Air Force Academy (USAFA) Vertical Axis Wind Turbine. Final report May 77-Sep 80  

Science Conference Proceedings (OSTI)

This report describes the design, fabrication, installation and testing of a small variable-speed vertical axis wind turbine (VAWT). This VAWT is unique in its installation using hand tools only; unconventional and simple support system; and variable speed operation under microprocessor control. Initial testing confirmed that the turbine can be controlled by commanded alternator field modulation. Further studies will be directed toward determination of an optimum control algorithm.

Kullgren, T.E.; Wiedemeier, D.W.

1980-09-01T23:59:59.000Z

72

An Analysis of Wind Direction and Horizontal Wind Component Fluctuations over Complex Terrain  

Science Conference Proceedings (OSTI)

Based on an extensive wind dataset over complex terrain, the commonly used small-angle approximation ?v ? ??V is studied and found to overestimate over all wind speeds and ?? values observed. This should be anticipated due to the assumptions ...

K. H. Papadopoulos; C. G. Helmis; G. T. Amanatidis

1992-09-01T23:59:59.000Z

73

© IC-EpsMsO NUMERICAL SIMULATION IN VERTICAL WIND AXIS TURBINE WITH PITCH  

E-Print Network (OSTI)

energy, pitch controlled blades Abstract: Wind energy is more and more used as a renewable energy source character. The present wind turbine is a small one which allows to be used on roofs or in gardens to light small areas like publicity boards, parking, roads or for water pumping, heating... The present turbine has a vertical axis. Each turbine blade combines a rotating movement around its own axis and around the main rotor axis. Due to this combination of movements, flow around this turbine is highly unsteady and needs to be modeled by unsteady calculation. One of the main problems of such geometry is to simulate the two combined movements. The present work is an extended study of one’s made in 2009. In the previous study, some results like contours of pressure and velocity fields were presented for elliptic blades for one specific constant rotational speed and benefits of combined rotating blades was shown. The present paper points up the influence of two different blades geometries for different rotational speeds, different blade stagger angles and different Reynolds numbers related to a wider range of wind speeds. 1

Controlled Blades; Bayeul-lainé Annie-claude; Dockter Aurore; Bois Gérard; Simonet Sophie

2013-01-01T23:59:59.000Z

74

Vertical axis wind turbine development. Final report, March 1, 1976-June 30, 1977  

DOE Green Energy (OSTI)

Theoretical and experimental research accomplished in evaluating an innovative concept for vertical axis wind turbines (VAWT) is described. The concept is that of using straight blades composed of circulation controlled airfoil sections. The theoretical analysis has been developed to determine the unsteady lift and moment characteristics of multiple-blade cross-flow wind turbines. To determine the drag data needed as input to the theoretical analysis, an outdoor test model VAWT has been constructed; design details, instrumentation, calibration results, and initial test results are reported. Initial testing was with fixed pitch blades having cross-sections of conventional symmetrical airfoils. Costs of building the test model are included, as well as cost estimates for blades constructed with composite materials. These costs are compared with those of other types of wind turbines.

Walters, R. E.; Fanucci, J. B.; Hill, P. W.; Migliore, P. G.

1979-07-01T23:59:59.000Z

75

Proceedings of the Vertical-Axis Wind Turbine Technology Workshop, Albuquerque, New Mexico, May 18--20, 1976  

DOE Green Energy (OSTI)

Separate abstracts are included for twenty-nine of the thirty papers presented concerning vertical axis wind turbines. One paper has previously been abstracted and included in the ERDA Energy Data Base and Energy Research Abstracts journal.

Not Available

1976-07-01T23:59:59.000Z

76

Development and Verification of a Computational Fluid Dynamics Model of a Horizontal-Axis Tidal Current Turbine  

SciTech Connect

This paper describes the development of a computational fluid dynamics (CFD) methodology to simulate the hydrodynamics of horizontal-axis tidal current turbines (HATTs). First, an HATT blade was designed using the blade element momentum method in conjunction with a genetic optimization algorithm. Several unstructured computational grids were generated using this blade geometry and steady CFD simulations were used to perform a grid resolution study. Transient simulations were then performed to determine the effect of time-dependent flow phenomena and the size of the computational timestep on the numerical solution. Qualitative measures of the CFD solutions were independent of the grid resolution. Conversely, quantitative comparisons of the results indicated that the use of coarse computational grids results in an under prediction of the hydrodynamic forces on the turbine blade in comparison to the forces predicted using more resolved grids. For the turbine operating conditions considered in this study, the effect of the computational timestep on the CFD solution was found to be minimal, and the results from steady and transient simulations were in good agreement. Additionally, the CFD results were compared to corresponding blade element momentum method calculations and reasonable agreement was shown. Nevertheless, we expect that for other turbine operating conditions, where the flow over the blade is separated, transient simulations will be required.

Lawson, Mi. J.; Li, Y.; Sale, D. C.

2011-01-01T23:59:59.000Z

77

Comparisons of Horizontal Winds Measured by Opposing Beams with the Flatland ST Radar and between Flatland Measurements and NMC Analyses  

Science Conference Proceedings (OSTI)

This study examines the consistency between VHF horizontal wind measurements and those interpolated from routine objective analyses. First, the agreement between the two U components and between the two V components measured on opposing beams (...

Patricia M. Pauley; Robert L. Creasey; Wallace L. Clark; Gregory D. Nastrom

1994-04-01T23:59:59.000Z

78

Retrievals of Horizontal Winds from Single-Doppler Clear-Air Data by Methods of Cross Correlation and Variational Analysis  

Science Conference Proceedings (OSTI)

Four methods for retrieval of the horizontal wind field are described and compared using single-Doppler observations of a sea-breeze front measured during the Convective and Precipitation/Electrification Experiment. The first method examined is ...

Stéphane Laroche; Isztar Zawadzki

1995-08-01T23:59:59.000Z

79

A Theory for the Retrievals of Virtual Temperature from Remote Measurements of Horizontal Winds and Thermal Radiation  

Science Conference Proceedings (OSTI)

This paper develops a theory for the estimation of virtual temperature from remote measurements of (i) emitted thermal radiation by microwave and infrared radiometers and (ii) horizontal winds by Doppler radars (or lidars). The problem of ...

Tzvi Gal-Chen

1988-06-01T23:59:59.000Z

80

Wind Energy Innovative Systems conference proceedings  

DOE Green Energy (OSTI)

Separate abstracts are included for 20 of the 22 papers presented concerning innovative wind turbines which vary in design from the standard horizontal-axis propellor-type wind turbines. Two papers have been previously included in the data base.

Vas, I. E. [ed.

1979-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "horizontal axis wind" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Vertical axis wind turbine power regulation through centrifugally pumped lift spoiling  

Science Conference Proceedings (OSTI)

This paper describes an approach for lowering the rated windspeeds of Darrieus-type vertical axis wind turbines (VAWTs) whose blades are hollow aluminum extrusions. The blades, which when rotating act as centrifugal pumps, are fitted with a series of small perforations distributed along a portion of the blades' span. By valving the ends of the hollow blades, flow into the blade ends and out of the perforations may be controlled. This flow can induce premature aerodynamic stall on the blade elements, thereby reducing both the rated power of the turbine and its cost-of-energy. The concept has been proven on the Sandia National Laboratories 5-m diameter research VAWT and force balance and flow visualization wind tunnel tests have been conducted using a blade section designed for the VAWT application.

Klimas, P.C.; Sladky, J.F. Jr.

1985-01-01T23:59:59.000Z

82

Comparison of Wind-Turbine Aeroelastic Codes Used for Certification: Preprint  

DOE Green Energy (OSTI)

NREL created aeroelastic simulators for horizontal-axis wind turbines accepted by Germanischer Lloyd (GL) WindEnergie GmbH for manufacturers to use for on-shore wind turbine certification.

Buhl, M. L., Jr.; Manjock, A.

2006-01-01T23:59:59.000Z

83

On Wind-Driven Mixed Layers with Strong Horizontal Gradients—A Theory with Application to Coastal Upwelling  

Science Conference Proceedings (OSTI)

A theory of a two-dimensional wind-driven diabatic ocean mixed layer with strong horizontal gradients is formulated analytically. An equation that allows the relaxation of the strict Ekman balance—Coriolis force against wind stress—is derived ...

R. A. De Szoeke; J. G. Richman

1984-02-01T23:59:59.000Z

84

Customized airfoils and their impact on VAWT (Vertical-Axis Wind Turbine) cost of energy  

DOE Green Energy (OSTI)

Sandia National Laboratories has developed a family of airfoils specifically designed for use in the equatorial portion of a Vertical-Axis Wind Turbine (VAWT) blade. An airfoil of that family has been incorporated into the rotor blades of the DOE/Sandia 34-m diameter VAWT Test Bed. The airfoil and rotor design process is reviewed. Comparisons with data recently acquired from flow visualization tests and from the DOE/Sandia 34-m diameter VAWT Test Bed illustrate the success that was achieved in the design. The economic optimization model used in the design is described and used to evaluate the effect of modifications to the current Test Bed blade. 1 tab., 11 figs., 13 refs.

Berg, D.E.

1990-01-01T23:59:59.000Z

85

Drop Shapes and Axis Ratio Distributions: Comparison between 2D Video Disdrometer and Wind-Tunnel Measurements  

Science Conference Proceedings (OSTI)

Comparisons of drop shapes between measurements made using 2D video disdrometer (2DVD) and wind-tunnel experiments are presented. Comparisons are made in terms of the mean drop shapes and the axis ratio distributions. Very close agreement of the ...

M. Thurai; V. N. Bringi; M. Szakáll; S. K. Mitra; K. V. Beard; S. Borrmann

2009-07-01T23:59:59.000Z

86

Wind Mixing In a Turbulent Surface Layer in the Presence of a Horizontal Density Gradient  

Science Conference Proceedings (OSTI)

The effect of a horizontal density gradient of buoyancy on the turbulent kinetic energy budget of the surface mixed layer in the ocean is discussed. The combination of a horizontal buoyancy gradient and a vertical shear of the horizontal velocity ...

Johan Rodhe

1991-07-01T23:59:59.000Z

87

RESEARCH ARTICLE Dynamic wind loads and wake characteristics of a wind turbine  

E-Print Network (OSTI)

RESEARCH ARTICLE Dynamic wind loads and wake characteristics of a wind turbine model of the unsteady vortex and turbulent flow structures in the near wake of a horizontal axis wind turbine model.e., aerodynamic forces and bending moments) acting on the wind turbine model by using a high-sensitive force

Hu, Hui

88

LQG control of horizontal wind turbines for blades and tower loads alleviation  

E-Print Network (OSTI)

a profoundly irregular primary source, the wind. The characteristics of the wind energy source are important in different aspects regarding wind energy exploitation. The energy available in the wind varies with the cube, by a continuous essay to significantly improve all aspects of a wind energy conversion system. Many research works

89

The Influence of Aerodynamic Stall on the Performance of Vertical Axis Wind Turbines.  

E-Print Network (OSTI)

??There is currently an increasing desire for local small-scale sustainable energy generation. This has lead to increased interest in the concept of the vertical axis… (more)

Edwards, Jonathan

2012-01-01T23:59:59.000Z

90

Implementation of a Two-Axis Servo-Hydraulic System for Full-Scale Fatigue Testing of Wind Turbine Blades  

DOE Green Energy (OSTI)

Recently, the blade fatigue testing capabilities at NREL were upgraded from single-axis to two-axis loading. To implement this, several practical challenges were addressed, as hardware complexity increased dramatically with two actuators applying the loads at right angles to each other. A custom bellcrank was designed and implemented to minimize the load angle errors and to prevent actuator side loading. The control system was upgraded to accept load and displacement feedback from two actuators. The inherent long strokes uniquely associated with wind turbine blade-tests required substantial real-time corrections for both the control and data systems. A custom data acquisition and control system was developed using a National Instruments LabVIEW platform that interfaces with proprietary servo-hydraulic software developed by MTS Corporation. Before testing, the program is run under quasi-static (slow speed) conditions and iterates to determine the correct operational control parameters for the controller, taking into consideration geometry, test speed, and phase angle errors between the two actuators. Comparisons are made between single-axis and two-axis test loads using actual test load data and load uncertainties are qualitatively described. To date, two fatigue tests have been completed and another is currently ongoing using NREL's two-axis capability.

Hughes, S. D.; Musial, W. D. [National Renewable Energy Lab., Golden, CO (US); Stensland, T. [Stensland Technologies (US)

1999-09-09T23:59:59.000Z

91

Wind shear for large wind turbine generators at selected tall tower sites  

DOE Green Energy (OSTI)

The objective of the study described in this report is to examine the nature of wind shear profiles and their variability over the height of large horizontal-axis wind turbines and to provide information on wind shear relevant to the design and opertion of large wind turbines. Wind turbine fatigue life and power quality are related through the forcing functions on the blade to the shapes of the wind shear profiles and their fluctuations over the disk of rotation.

Elliott, D.L.

1984-04-01T23:59:59.000Z

92

Addendum to a proposal to NSF to sponsor a vertical-axis wind turbine research program  

SciTech Connect

Information is presented concerning the performance evaluation of a 15 foot-diameter test bed Darrieus rotor, Darrieus rotor wind tunnel tests, Savonius rotor wind tunnel tests, blade manufacturing techniques for 15 foot-diameter and 35 foot-diameter wind turbines, static and dynamic structural analysis, production prototype design of a 15 foot-diameter turbine, production prototype design of 35 foot-diameter turbine, and aerodynamic performance studies.

Blackwell, B.F.; Feltz, L.V.; Rightley, E.C.

1974-11-01T23:59:59.000Z

93

Axis Ratios of Water Drops Levitated in a Vertical Wind Tunnel  

Science Conference Proceedings (OSTI)

The shapes of falling raindrops are often significantly altered by drop oscillations, complicating dual-polarization radar methods that rely on a predictable, monotonic variation of drop axis ratio ? with equivolume drop diameter d. This ...

B. K. Jones; J. R. Saylor

2009-11-01T23:59:59.000Z

94

Design and construction of vertical axis wind turbines using dual-layer vacuum-forming  

E-Print Network (OSTI)

How does one visualize wind? Is it the way trees bend in a strong gust or the way smoke is carried in a breeze? What if wind could be visualized using design, technology, and light? This thesis documents the design of a ...

Carper, Christopher T

2010-01-01T23:59:59.000Z

95

Medium-solidity Vertical Axis Wind Turbines for use in Urban Environments S. Tullis, A. Fiedler, K. McLaren, S. Ziada  

E-Print Network (OSTI)

Vertical axis wind turbines are currently experiencing a renewed interest in small- scale applications in urban environments. However, vibration is a large issue with VAWTs due to their highly variable blade. A prototype of a commercially available 2.5 kW VAWT was wind tunnel tested to investigate its power

Tullis, Stephen

96

Approach to the fatigue analysis of vertical-axis wind-turbine blades  

DOE Green Energy (OSTI)

A cursory analysis of the stress history of wind turbine blades indicates that a single stress level at each wind speed does not adequately describe the blade stress history. A statistical description is required. Blade stress data collected from the DOE/ALCOA Low Cost experimental turbines indicate that the Rayleigh probability density function adequately describes the distribution of vibratory stresses at each wind speed. The Rayleigh probability density function allows the distribution of vibratory stresses to be described by the RMS of the stress vs. time signal. With the RMS stress level described for all wind speeds, the complete stress history of the turbine blades is known. Miner's linear cumulative damage rule is used as a basis for summing the fatigue damage over all operating conditions. An analytical expression is derived to predict blade fatigue life.

Veers, P.S.

1981-09-01T23:59:59.000Z

97

Horizontal Divergence and Vertical Velocity Retrievals from Doppler Radar and Wind Profiler Observations  

Science Conference Proceedings (OSTI)

Vertical motion profiles can be diagnosed with the mass continuity equation using horizontal divergence fields derived from various single-Doppler radar techniques such as EVAD (extended velocity-azimuth display), CEVAD (concurrent extended ...

Robert Cifelli; Steven A. Rutledge; Dennis J. Boccippio; Thomas Matejka

1996-10-01T23:59:59.000Z

98

Integral-Field Spectroscopy of the Post Red Supergiant IRC +10420: evidence for an axi-symmetric wind  

E-Print Network (OSTI)

We present NAOMI/OASIS adaptive-optics assisted integral-field spectroscopy of the transitional massive hypergiant IRC +10420, an extreme mass-losing star apparently in the process of evolving from a Red Supergiant toward the Wolf-Rayet phase. To investigate the present-day mass-loss geometry of the star, we study the appearance of the line-emission from the inner wind as viewed when reflected off the surrounding nebula. We find that, contrary to previous work, there is strong evidence for wind axi-symmetry, based on the equivalent-width and velocity variations of H$\\alpha$ and Fe {\\sc ii} $\\lambda$6516. We attribute this behaviour to the appearance of the complex line-profiles when viewed from different angles. We also speculate that the Ti {\\sc ii} emission originates in the outer nebula in a region analogous to the Strontium Filament of $\\eta$ Carinae, based on the morphology of the line-emission. Finally, we suggest that the present-day axisymmetric wind of IRC +10420, combined with its continued blueward evolution, is evidence that the star is evolving toward the B[e] supergiant phase.

Ben Davies; René D. Oudmaijer; Kailash C. Sahu

2007-08-16T23:59:59.000Z

99

Integral-Field Spectroscopy of the Post Red Supergiant IRC +10420: evidence for an axi-symmetric wind  

E-Print Network (OSTI)

We present NAOMI/OASIS adaptive-optics assisted integral-field spectroscopy of the transitional massive hypergiant IRC +10420, an extreme mass-losing star apparently in the process of evolving from a Red Supergiant toward the Wolf-Rayet phase. To investigate the present-day mass-loss geometry of the star, we study the appearance of the line-emission from the inner wind as viewed when reflected off the surrounding nebula. We find that, contrary to previous work, there is strong evidence for wind axi-symmetry, based on the equivalent-width and velocity variations of H$\\alpha$ and Fe {\\sc ii} $\\lambda$6516. We attribute this behaviour to the appearance of the complex line-profiles when viewed from different angles. We also speculate that the Ti {\\sc ii} emission originates in the outer nebula in a region analogous to the Strontium Filament of $\\eta$ Carinae, based on the morphology of the line-emission. Finally, we suggest that the present-day axisymmetric wind of IRC +10420, combined with its continued blueward...

Davies, Ben; Sahu, Kailash C

2007-01-01T23:59:59.000Z

100

Horizontal wind/water wheel with vertical lift a superior protype model  

Science Conference Proceedings (OSTI)

A rotary device is described for capturing fluid flow and converting it to rotary mechanical energy, comprising: a single sheet of thin material having two relatively inverted generally right triangular portions, each having an hypotenuse-like base one-half of which, nearest a central axis point, has a tab-like extension that is partially perforated near the central axis point comprising an angle of slightly less than 180/sup 0/ with the remaining portion of the hypotenuse-like base, with the corresponding edges of each portion parallel to the other and slightly spaced apart from each other, the generally triangular portions each having a crease line extending from the hypotenuse-like base to the right angle vertex slightly offset towards the central axis point, the generally triangular portions being symmetrical about the central axis point and joined together by a generally parallelogram-shaped midsection with a pair of longer edges joined at an angle to a pair of shorter edges, the longer edges being collinear with the sides of the generally triangular portions nearest the central axis point, the shorter edges being respective extensions of the hypotenuse-like bases of the generally triangular portions having the tab-like extensions partially perforated near the central axis point to accommodate folded portions of the thin material; a rectangular-shaped tab, extending perpendicularly from the base of one of the generally triangular portions from near its distal vertex to a point short of the right angle vertex crease line to an outer edge parallel to the base, the tab having perforations along the base and along the outer edge.

Wittwer, J.J.

1986-06-24T23:59:59.000Z

Note: This page contains sample records for the topic "horizontal axis wind" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

PERFORMANCE ENHANCEMENT OF WIND TURBINE POWER REGULATION BY SWITCHED LINEAR CONTROL  

E-Print Network (OSTI)

PERFORMANCE ENHANCEMENT OF WIND TURBINE POWER REGULATION BY SWITCHED LINEAR CONTROL D.J.Leith W Power regulation of horizontal-axis grid-connected up-wind constant-speed pitch-regulated wind turbines, switched linear control is more suited for application to wind turbines than the nonlinear control strategy

Duffy, Ken

102

Dynamic Analysis of a Grid-Connected Wind Electric Generator with Embedded Static VAR Compensator  

Science Conference Proceedings (OSTI)

This paper describes modeling and simulation of Wind Electric Generator (WEG) comprising a pitch controlled Horizontal Axis Wind Turbine (HAWT) coupled to squirrel cage induction generator through a gear. The generic issue of VAR drain from the grid ... Keywords: Wind turbine, induction generator, two mass model - drive train, SVC, wind electric generator dynamics

Vishnuvardhanan V.; Sasi K. Kottayil

2009-12-01T23:59:59.000Z

103

Riso-M-2546 g Wind Turbine Test  

E-Print Network (OSTI)

Riso-M-2546 g Wind Turbine Test Wind Matic WM 17S Troels Friis Pedersen The Test Station TEST WIND MATIC WM 17S Troels Friis Pedersen The Test Station for Windmills, Ris0 Abstract* The report; DYNAMIC LOADS; HORIZONTAL AXIS TUR- BINES; MECHANICAL TESTS; NOISE; PERFORMANCE TESTING; POWER GENERATION

104

Preliminary design and viability consideration of external, shroud-based stators in wind turbine generators  

E-Print Network (OSTI)

Horizontal-axis wind turbine designs often included gearboxes or large direct-drive generators to compensate for the low peripheral speeds of the turbine hub. To take advantage of high blade tip speeds, an alternative ...

Shoemaker-Trejo, Nathaniel (Nathaniel Joseph)

2012-01-01T23:59:59.000Z

105

High Horizontal and Vertical Resolution Limited-Area Model: Near-Surface and Wind Energy Forecast Applications  

Science Conference Proceedings (OSTI)

As harvesting of wind energy grows, so does the need for improved forecasts from the surface to the top of wind turbines. To improve mesoscale forecasts of wind, temperature, and dewpoint temperature in this layer, two different approaches are ...

Natacha B. Bernier; Stéphane Bélair

2012-06-01T23:59:59.000Z

106

Establishing a Comprehensive Wind Energy Program  

SciTech Connect

This project was directed at establishing a comprehensive wind energy program in Indiana, including both educational and research components. A graduate/undergraduate course ME-514 - Fundamentals of Wind Energy has been established and offered and an interactive prediction of VAWT performance developed. Vertical axis wind turbines for education and research have been acquired, instrumented and installed on the roof top of a building on the Calumet campus and at West Lafayette (Kepner Lab). Computational Fluid Dynamics (CFD) calculations have been performed to simulate these urban wind environments. Also, modal dynamic testing of the West Lafayette VAWT has been performed and a novel horizontal axis design initiated. The 50-meter meteorological tower data obtained at the Purdue Beck Agricultural Research Center have been analyzed and the Purdue Reconfigurable Micro Wind Farm established and simulations directed at the investigation of wind farm configurations initiated. The virtual wind turbine and wind turbine farm simulation in the Visualization Lab has been initiated.

Fleeter, Sanford [Purdue University

2012-09-30T23:59:59.000Z

107

Effects of blade configuration on flow distribution and power output of a zephyr vertical axis wind turbine.  

E-Print Network (OSTI)

??Worldwide interest in renewable energy systems has increased dramatically, due to environmental concerns like climate change and other factors. Wind power is a major source… (more)

Ajedegba, John Oviemuno

2008-01-01T23:59:59.000Z

108

Aerodynamic characteristics of seven symmetrical airfoil sections through 180-degree angle of attack for use in aerodynamic analysis of vertical axis wind turbines  

Science Conference Proceedings (OSTI)

When work began on the Darrieus vertical axis wind turbine (VAWT) program at Sandia National Laboratories, it was recognized that there was a paucity of symmetrical airfoil data needed to describe the aerodynamics of turbine blades. Curved-bladed Darrieus turbines operate at local Reynolds numbers (Re) and angles of attack (..cap alpha..) seldom encountered in aeronautical applications. This report describes (1) a wind tunnel test series conducted at moderate values of Re in which 0 less than or equal to ..cap alpha.. less than or equal to 180/sup 0/ force and moment data were obtained for four symmetrical blade-candidate airfoil sections (NACA-0009, -0012, -0012H, and -0015), and (2) how an airfoil property synthesizer code can be used to extend the measured properties to arbitrary values of Re (10/sup 4/ less than or equal to Re less than or equal to 10/sup 7/) and to certain other section profiles (NACA-0018, -0021, -0025).

Sheldahl, R E; Klimas, P C

1981-03-01T23:59:59.000Z

109

Observation of 3–6-Day Meridional Wind Oscillations over the Tropical Pacific, 1973–1992: Horizontal Structure and Propagation  

Science Conference Proceedings (OSTI)

Twenty years of rawinsonde data (1973–1992) were examined in conjunction with European Centre for Medium-Range Weather Forecasts (ECMWF) analyses and outgoing longwave radiation (OLR) in 1980–1989 to determine the horizontal structure, ...

Timothy J. Dunkerton; Mark P. Baldwin

1995-05-01T23:59:59.000Z

110

Optimization of a Savonius rotor vertical-axis wind turbine for use in water pumping systems in rural Honduras  

E-Print Network (OSTI)

The D-lab Honduras team designed and constructed a wind-powered water pump in rural Honduras during IAP 2007. Currently, the system does not work under its own power and water must be pumped by hand. This thesis seeks to ...

Zingman, Aron (Aron Olesen)

2007-01-01T23:59:59.000Z

111

The Vibration Frequencies of Wind Turbine Steel Tower by Transfer Matrix Method  

Science Conference Proceedings (OSTI)

Large-scale wind turbine structure is simplified as a slender cantilever beam with variable sections subject to complex loads configuration. An analytical procedure to estimate not only natural frequencies but also vibration mode shapes of thin-walled ... Keywords: horizontal axis wind turbine tower, natural frequency, transfer matrix method, free vibration

Wang Meng; Wang Zhangqi

2011-01-01T23:59:59.000Z

112

Unsteady Aerodynamics Experiment Phase VI: Wind Tunnel Test Configurations and Available Data Campaigns  

DOE Green Energy (OSTI)

The primary objective of the insteady aerodynamics experiment was to provide information needed to quantify the full-scale, three-dimensional aerodynamic behavior of horizontal-axis wind turbines. This report is intended to familiarize the user with the entire scope of the wind tunnel test and to support the use of the resulting data.

Hand, M. M.; Simms, D. A.; Fingersh, L. J.; Jager, D. W.; Cotrell, J. R.; Schreck, S.; Larwood, S. M.

2001-12-01T23:59:59.000Z

113

Microsoft Word - WACM wind.doc  

NLE Websites -- All DOE Office Websites (Extended Search)

WACM Wind Production WACM Wind Production Summary Overview October 2006 Summary by Joseph Liberatore 2 The following report is designed to give a graphical representation of the wind production on Western's transmission system in the Western Area Colorado/Missouri (WACM) control area for five (5) wind farms. A map and the general locations of the various farms is shown in figure A. Production output graphs of farms A, B, C, D and E were created to be read as follows The horizontal (X) axis is hour of day in military time and The vertical (Y) axis is month of year from January thru December, 1 thru 12 respectively. Color variations are to be interpreted as follows: Dark blue areas represent little or no wind production and are graduated to bright red which depict maximum wind farm output. All levels are normalized

114

NREL: Wind Research - SWIFT Wind Turbine Testing and Results  

NLE Websites -- All DOE Office Websites (Extended Search)

SWIFT Wind Turbine Testing and Results SWIFT Wind Turbine Testing and Results The SWIFT wind turbine. Text Version As part of the National Renewable Energy Laboratory and U.S. Department of Energy (NREL/DOE) Independent Testing project, NREL is testing the SWIFT small wind turbine at the National Wind Technology Center (NWTC). The competitive grant was awarded to Cascade Engineering. The SWIFT is a 1-kilowatt (kW), five-bladed with outer ring, horizontal-axis upwind small wind turbine. The turbine's rotor diameter is 2 meters, and its hub height is 13.72 meters. The SWIFT uses a single-phase permanent-magnet generator rated at 1 kW grid connected through an inverter at 240 volts AC. Testing Summary Supporting data and explanations for data provided in this table will be provided in the final reports. Data presented are preliminary and subject

115

Using a new characterization of turbulent wind for accurate correlation of wind turbine response with wind speed  

SciTech Connect

The turbulence encountered by a point on a rotating wind turbine blade has characteristics that in some important respects are different from those measured by a stationary anemometer. The conventional one-peaked continuous spectrum becomes, broadly, a two-peaked spectrum that in addition contains a set of narrow-band spikes of turbulence energy, one centered on the frequency of rotor rotation and the others centered on multiples of that frequency. The rotational sampling effect on wind spectra is quantified using measurements of wind velocity by anemometers on stationary crosswind circular arrays. Characteristics of fluctuating wind are compared to measured fluctuations of bending moments of the rotor blades and power output fluctuations of a horizontal-axis wind turbine at the same site. The wind characteristics and the correlations between wind fluctuations and wind turbine fluctuations provide a basis for improving turbine design, siting, and control. 6 refs., 11 figs., 1 tab.

Connell, J.R.; George, R.L.

1987-09-01T23:59:59.000Z

116

Experimental and analytical research on the aerodynamics of wind turbines. Mid-term technical report, June 1--December 31, 1975  

SciTech Connect

The successful development of reliable, cost competitive horizontal axis, propeller-type wind energy conversion systems (WECS) is strongly dependent on the availability of advanced technology for each of the system components. Past experience and current studies of this type of wind energy conversion systems have shown that the wind turbine subsystem most significantly effects the system's cost effectiveness and performance capability. Thus adequate technology bases are essential for all elements of the wind turbine design. Information is presented concerning aerodynamic design and performance technology, wind turbine parametric performance study, selection of model wind turbine configurations, and structural design of wind turbine models.

Rohrbach, C.

1976-02-01T23:59:59.000Z

117

Experimental and analytical research on the aerodynamics of wind turbines. Mid-term technical report, June 1--December 31, 1975  

DOE Green Energy (OSTI)

The successful development of reliable, cost competitive horizontal axis, propeller-type wind energy conversion systems (WECS) is strongly dependent on the availability of advanced technology for each of the system components. Past experience and current studies of this type of wind energy conversion systems have shown that the wind turbine subsystem most significantly effects the system's cost effectiveness and performance capability. Thus adequate technology bases are essential for all elements of the wind turbine design. Information is presented concerning aerodynamic design and performance technology, wind turbine parametric performance study, selection of model wind turbine configurations, and structural design of wind turbine models.

Rohrbach, C.

1976-02-01T23:59:59.000Z

118

NREL: Wind Research - Abundant Renewable Energy's ARE 442 Wind Turbine  

NLE Websites -- All DOE Office Websites (Extended Search)

Abundant Renewable Energy's ARE 442 Wind Turbine Testing and Results Abundant Renewable Energy's ARE 442 Wind Turbine Testing and Results Get the Adobe Flash Player to see this video. A video of Abundant Renewable Energy's ARE 442 wind turbine. Text Version As part of the National Renewable Energy Laboratory and U.S. Department of Energy (NREL/DOE) Independent Testing project, NREL tested Abundant Renewable Energy's ARE 442 turbine at the National Wind Technology Center (NWTC). The ARE 442 is a 10-kilowatt (kW), three-bladed, horizontal-axis upwind small wind turbine. It has a hub height of 30.9 meters and a rotor diameter of 7.2 meters. The turbine has a single-phase permanent-magnet generator that operates at variable voltages up to 410 volts AC. Testing Summary The summary of the tests is below with the final reports.

119

SERI advanced wind turbine blades  

DOE Green Energy (OSTI)

The primary goal of the Solar Energy Research Institute`s (SERI) advanced wind turbine blades is to convert the kinetic energy in the wind into mechanical energy in an inexpensive and efficient manner. To accomplish this goal, advanced wind turbine blades have been developed by SERI that utilize unique airfoil technology. Performance characteristics of the advanced blades were verified through atmospheric testing on fixed-pitch, stall-regulated horizontal-axis wind turbines (HAWTs). Of the various wind turbine configurations, the stall-regulated HAWT dominates the market because of its simplicity and low cost. Results of the atmospheric tests show that the SERI advanced blades produce 10% to 30% more energy than conventional blades. 6 refs.

Tangler, J.; Smith, B.; Jager, D.

1992-02-01T23:59:59.000Z

120

SERI advanced wind turbine blades  

DOE Green Energy (OSTI)

The primary goal of the Solar Energy Research Institute's (SERI) advanced wind turbine blades is to convert the kinetic energy in the wind into mechanical energy in an inexpensive and efficient manner. To accomplish this goal, advanced wind turbine blades have been developed by SERI that utilize unique airfoil technology. Performance characteristics of the advanced blades were verified through atmospheric testing on fixed-pitch, stall-regulated horizontal-axis wind turbines (HAWTs). Of the various wind turbine configurations, the stall-regulated HAWT dominates the market because of its simplicity and low cost. Results of the atmospheric tests show that the SERI advanced blades produce 10% to 30% more energy than conventional blades. 6 refs.

Tangler, J.; Smith, B.; Jager, D.

1992-02-01T23:59:59.000Z

Note: This page contains sample records for the topic "horizontal axis wind" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Rotationally sampled wind characteristics and correlations with MOD-OA wind turbine response  

SciTech Connect

This report presents results of a comprehensive wind and wind turbine measurement program: the Clayton, New Mexico, vertical plane array/MOD-OA project. In this experiment, the turbulent wind was measured for a large array of fixed anemometers located two blade diameters upwind of a 200-kW horizontal-axis wind turbine (HAWT). Simultaneously, key wind turbine response parameters were also measured. The first of two major objectives of this experiment was to determine the turbulent wind, rotationally sampled to emulate the motion of the wind turbine blade, for the range of different wind speeds and stability classes actually experienced by the wind turbine. The second major objective was to correlate this rotationally sampled wind with the wind turbine blade stress and power, in order to assess the usefulness of the wind measurements for wind turbine loads testing a prediction. Time series of rotationally sampled winds and wind turbine blade bending moments and power were converted to frequency spectra using Fourier transform techniques. These spectra were used as the basis for both qualitative and quantitative comparisons among the various cases. A quantitative comparison between the rotationally sampled wind input and blade bending response was made, using the Fourier spectra to estimate the blade transfer function. These transfer functions were then used to calculate an approximate damping coefficient for the MOD-OA fiberglass blade.

George, R.L.; Connell, J.R.

1984-09-01T23:59:59.000Z

122

NREL: Wind Research - Entegrity Wind Systems's EW50 Turbine Testing and  

NLE Websites -- All DOE Office Websites (Extended Search)

Entegrity Wind Systems's EW50 Turbine Testing and Results Entegrity Wind Systems's EW50 Turbine Testing and Results Entegrity Wind Systems' EW50 wind turbine. Text Version As part of the National Renewable Energy Laboratory and U.S. Department of Energy (NREL/DOE) Independent Testing project, NREL tested Entegrity Wind Systems' EW50 turbine at the National Wind Technology Center (NWTC). The EW50 is a 50-kilowatt (kW), three-bladed, horizontal-axis downwind small wind turbine. The turbine's rotor diameter is 15 meters, and its hub height is 30.5 meters. It has a three-phase induction generator that operates at 480 volts AC. Testing Summary The summary of the tests is listed below, along with the final reports. Cumulative Energy Production 3/11/2009: 17; 3/12/2009: 17; 3/13/2009: 17; 3/14/2009: 17; 3/15/2009: 17;

123

Wind power for the Creek Nation. Final report  

SciTech Connect

An Enertech 1800 horizontal-axis wind powered electric generator was purchased and interphased with the electric utility system provided to the Creek Nation by the Public Service Company of Oklahoma. Objectives of the work include: to determine the economic feasibility of wind power for the Creek Nation region; to educate the Creek Nation and other Indian tribes about the potential use of wind power; and to accumulate valuable climatic data through an on-site wind survey at a height of 60' over a long period of time. (LEW)

Not Available

1982-01-01T23:59:59.000Z

124

Load attenuating passively adaptive wind turbine blade  

DOE Patents (OSTI)

A method and apparatus for improving wind turbine performance by alleviating loads and controlling the rotor. The invention employs the use of a passively adaptive blade that senses the wind velocity or rotational speed, and accordingly modifies its aerodynamic configuration. The invention exploits the load mitigation prospects of a blade that twists toward feather as it bends. The invention includes passively adaptive wind turbine rotors or blades with currently preferred power control features. The apparatus is a composite fiber horizontal axis wind-turbine blade, in which a substantial majority of fibers in the blade skin are inclined at angles of between 15 and 30 degrees to the axis of the blade, to produces passive adaptive aeroelastic tailoring (bend-twist coupling) to alleviate loading without unduly jeopardizing performance.

Veers, Paul S. (Albuquerque, NM); Lobitz, Donald W. (Albuquerque, NM)

2003-01-01T23:59:59.000Z

125

Horizontal Variability in 10 m Wind Velocities as Observed at Two Prairie Sites Separated by a Distance of 7.5 km  

Science Conference Proceedings (OSTI)

It is important to assess the representativeness of mesoscale wind data because most short range pollution models assume that wind velocity will remain constant over distances in the order of 10 km. Previous observational studies have shown that ...

D. M. Leahey; M. C. Hansen; M. B. Schroeder

1989-11-01T23:59:59.000Z

126

Dynamic stall on wind turbine blades  

DOE Green Energy (OSTI)

Dynamic loads must be predicted accurately in order to estimate the fatigue life of wind turbines operating in turbulent environments. Dynamic stall contributes to increased dynamic loads during normal operation of all types of horizontal-axis wind turbine (HAWTs). This report illustrates how dynamic stall varies throughout the blade span of a 10 m HAWT during yawed and unyawed operating conditions. Lift, drag, and pitching moment coefficients during dynamics stall are discussed. Resulting dynamic loads are presented, and the effects of dynamic stall on yaw loads are demonstrated using a yaw loads dynamic analysis (YAWDYN). 12 refs., 22 figs., 1 tab.

Butterfield, C.P.; Simms, D.; Scott, G. [National Renewable Energy Lab., Golden, CO (United States)] [National Renewable Energy Lab., Golden, CO (United States); Hansen, A.C. [Utah Univ., Salt Lake City, UT (United States)] [Utah Univ., Salt Lake City, UT (United States)

1991-12-01T23:59:59.000Z

127

Direct Determination of Wind Shears from the Gradients of Satellite Radiance Observations  

Science Conference Proceedings (OSTI)

To the extent that the stratosphere wind field is close to geostrophic, the thermal wind is a good approximation to the vertical wind shear (vertical variation of the horizontal wind). And since the thermal wind is proportional to the horizontal ...

George Ohring; Binyamin Neeman; Louis D. Duncan

1981-11-01T23:59:59.000Z

128

Steerable vertical to horizontal energy transducer for mobile robots  

DOE Patents (OSTI)

The present invention provides a steerable vertical to horizontal energy transducer for mobile robots that less complex and requires less power than two degree of freedom tilt mechanisms. The present invention comprises an end effector that, when mounted with a hopping actuator, translates along axis (typically vertical) actuation into combined vertical and horizontal motion. The end effector, or foot, mounts with an end of the actuator that moves toward the support surface (typically a floor or the earth). The foot is shaped so that the first contact with the support surface is off the axis of the actuator. Off-axis contact with the support surface generates an on-axis force (typically resulting in vertical motion) and a moment orthogonal to the axis. The moment initiates a horizontal tumbling motion, and tilts the actuator so that its axis is oriented with a horizontal component and continued actuation generates both vertical and horizontal force.

Spletzer, Barry L. (Albuquerque, NM); Fischer, Gary J. (Albuquerque, NM); Feddema, John T. (Albuquerque, NM)

2001-01-01T23:59:59.000Z

129

Optimizing wind turbine control system parameters  

Science Conference Proceedings (OSTI)

The impending expiration of the levelized period in the Interim Standard Offer Number 4 (ISO4) utility contracts for purchasing wind-generated power in California mandates, more than ever, that windplants be operated in a cost-effective manner. Operating plans and approaches are needed that maximize the net revenue from wind parks--after accounting for operation and maintenance costs. This paper describes a design tool that makes it possible to tailor a control system of a wind turbine (WT) to maximize energy production while minimizing the financial consequences of fatigue damage to key structural components. Plans for code enhancements to include expert systems and fuzzy logic are discussed, and typical results are presented in which the code is applied to study the controls of a generic Danish 15-m horizontal axis wind turbine (HAWT).

Schluter, L.L. [Sandia National Labs., Albuquerque, NM (United States); Vachon, W.A. [Vachon (W.A.) and Associates, Inc., Manchester, MA (United States)

1993-08-01T23:59:59.000Z

130

Vapor Flow to Horizontal Wells in Unsaturated Zones Hongbin Zhan* and Eungyu Park  

E-Print Network (OSTI)

Vapor Flow to Horizontal Wells in Unsaturated Zones Hongbin Zhan* and Eungyu Park ABSTRACT and vaporthree dimensional form for a horizontal-well sink in an unsaturated zone. This is done by solving; horizontal-well axis to obtain the solution of flow to a horizontal-well Zhan and Cao, 2000). Horizontal

Zhan, Hongbin

131

Effects of Precipitation on UHF Wind Profiler Measurements  

Science Conference Proceedings (OSTI)

Horizontal winds in the presence of precipitation were measured routinely with a UHF (405 MHz) Wind Profiler. The profiler had five beam-pointing positions so independent measurements of horizontal winds could be compared to determine relative ...

D. B. Wuertz; B. L. Weber; R. G. Strauch; A. S. Frisch; C. G. Little; D. A. Merritt; K. P. Moran; D. C. Welsh

1988-06-01T23:59:59.000Z

132

Analysis of the Madaras Rotor Power Plant: an alternate method for extracting large amounts of power from the wind. Volume 2. Technical report  

DOE Green Energy (OSTI)

The purpose of the program was to analyze and up-date the design of the Madaras Rotor Power Plant concept that had been developed in the 1930's to determine the technical and economic feasibility of this system to be competitive with conventional horizontal axis wind turbines. A four-task program consisting of a series of wind tunnel tests, an electro-mechanical analysis, a performance analysis, and a cost analysis was conducted.

Whitford, D.H.; Minardi, J.E.; West, B.S.; Dominic, R.J.

1978-06-01T23:59:59.000Z

133

Model for simulating rotational data for wind turbine applications  

DOE Green Energy (OSTI)

This document describes a wind simulation model to be used in relation to wind turbine operations. The model is a computer code written in FORTRAN 77. The model simulates turbulence and mean wind effects as they are experienced at a rotating point on the blade of either a horizontal-axis wind turbine (HAWT) or a vertical-axis wind turbine (VAWT). The model is fast, requiring 15 to 120 seconds of VAX execution time to produce a simulation and related statistics. The model allows the user to set a number of wind parameters so that he may evaluate the uncertainty of model results as well as their typical values. When this capability is combined with short execution time, the user can quickly produce a number of simulations based on reasonable variation of input parameters and can use these simulations to obtain a range of wind turbine responses to the turbulence. This ability is important because some of the wind parameters that cannot be precisely evaluated should be prescribed over a range of values. This document is essentially a user's guide. Its features include theoretical derivations, samples of output, comparisons of measured and modeled results, a listing of the FORTRAN code, a glossary for the code, and the input and output of a sample run.

Powell, D.C.; Connell, J.R.

1986-04-01T23:59:59.000Z

134

An approach to the development and analysis of wind turbine control algorithms  

DOE Green Energy (OSTI)

The objective of this project is to develop the capability of symbolically generating an analytical model of a wind turbine for studies of control systems. This report focuses on a theoretical formulation of the symbolic equations of motion (EOMs) modeler for horizontal axis wind turbines. In addition to the power train dynamics, a generic 7-axis rotor assembly is used as the base model from which the EOMs of various turbine configurations can be derived. A systematic approach to generate the EOMs is presented using d`Alembert`s principle and Lagrangian dynamics. A Matlab M file was implemented to generate the EOMs of a two-bladed, free yaw wind turbine. The EOMs will be compared in the future to those of a similar wind turbine modeled with the YawDyn code for verification. This project was sponsored by Sandia National Laboratories as part of the Adaptive Structures and Control Task. This is the final report of Sandia Contract AS-0985.

Wu, K.C.

1998-03-01T23:59:59.000Z

135

Rotor Speed Dependent Yaw Control of Wind Turbines Based on Empirical Data  

Science Conference Proceedings (OSTI)

When extracting energy from the wind using horizontal-axis upwind wind turbines, a primary condition for maximum power yield is the ability to align the rotor axis with the dominating wind direction. Attempts have been made to improve yaw alignment by applying advanced measurement techniques such as LIDARs. This study is focused at assessing the current performance of an operating turbine and exploring how the yaw alignment can be improved using existing measurements. By analyzing available turbine and met mast data a correction scheme for the original yaw alignment system is synthesized. The correction scheme is applied and it is seen that with the correction scheme in place, the power yield below rated is raised 1-5 percent. Furthermore, results indicate that blade load variations are decreased when the correction scheme is applied. The results are associated with uncertainties due to the amount of available data and the wind site climate. Further work should be focused at gathering more experimental data.

Kragh, K. A.; Fleming, P. A.

2012-01-01T23:59:59.000Z

136

Plan for the Wind Power Device to Make the Best of Earth Wind Energy  

Science Conference Proceedings (OSTI)

To make the best of wind energy resources on the earth surface, the plan for a new type of wind power device, named Multiple wind wheel Wind power Device, MWD in short, was put forward. MWD composes steel tower, trusses, generator, long axis, wind turbines ... Keywords: clean renewable sources, wind energy, wind power, wind turbine

Bingwen Zhang; Yingjin Zhang

2010-06-01T23:59:59.000Z

137

Aerodynamic testing of a rotating wind turbine blade  

DOE Green Energy (OSTI)

Aerodynamic, load, flow-visualization, and inflow measurements were taken on a downwind horizontal-axis wind turbine (HAWT). A video camera mounted on the rotor recorded video images of tufts attached to the low-pressure side of the blade. Strain gages, mounted every 10% of the blade's span, provided load and pressure measurements. Pressure taps at 32 chordwise positions recorded pressure distributions. Wind inflow was measured via a vertical-plane array of anemometers located 10 m upwind. The objectives of the test were to address whether airfoil pressure distributions measured on a rotating blade differed from those measured in the wind tunnel, if radial flow near or in the boundary layer of the airfoil affected pressure distributions, if dynamic stall could result in increased dynamic loads, and if the location of the separation boundary measured on the rotating blade agreed with that measured in two-dimensional flow in the wind tunnel. 6 refs., 9 figs., 1 tab.

Butterfield, C.P.; Nelsen, E.N.

1990-01-01T23:59:59.000Z

138

Large wind turbine siting handbook: television interference assessment. Final subcontract report  

DOE Green Energy (OSTI)

The rotating blades of a horizontal axis wind turbine can distort the video portion of a television signal and thereby interfere with TV reception in the vicinity of the machine. The nature of this interference is described and methods are presented for calculating the zone within which the interference may be severs. Specific results are given for the MOD-OA, MOD-1 and MOD-2 machines as functions of the TV frequency.

Senior, T B.A.; Sengupta, D L

1983-01-01T23:59:59.000Z

139

Lidar measurement of wind velocity turbulence spectra encountered by a rotating turbine blade  

DOE Green Energy (OSTI)

A homodyne CO/sub 2/ lidar system beam was conically scanned around a horizontal axis to measure the wind speed and turbulence characteristics encountered by a rotating turbine blade. Turbulence spectra obtained from the scanning lidar differed considerably from those calculated from fixed-point anemometer measurements, showing a redistribution of energy from lower to higher frequencies. The differences appeared more pronounced during periods when the atmosphere was stable.

Hardesty, R.M.; Korrell, J.A.; Hall, F.F. Jr.

1982-01-01T23:59:59.000Z

140

A Stochastic Model for Wind Occurrence  

Science Conference Proceedings (OSTI)

Knowledge of wind occurrence in any location is a valuable input in most agricultural studies. A bivariate stochastic process is proposed here as a model of daily wind occurrence. Two wind variables have been considered: 1) horizontal direction, ...

Jose Roldan-Cañas; Adela Garcia-Guzman; Alberto Losada-Villasante

1982-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "horizontal axis wind" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Revisiting an Old Concept: The Gradient Wind  

Science Conference Proceedings (OSTI)

The gradient wind is defined as a horizontal wind having the same direction as the geostrophic wind but with a magnitude consistent with a balance of three forces: the pressure gradient force, the Coriolis force, and the centrifugal force arising ...

Keith F. Brill

142

Preliminary Evaluation of the First NOAA Demonstration Network Wind Profiler  

Science Conference Proceedings (OSTI)

The first wind profiler for a demonstration network of wind profilers recently passed the milestone of 300 h of continuous operation. The horizontal wind component measurements taken during that period are compared with the WPL Platteville wind ...

B. L. Weber; D. B. Wuertz; R. G. Strauch; D. A. Merritt; K. P. Moran; D. C. Law; D. van de Kamp; R. B. Chadwick; M. H. Ackley; M. F. Barth; N. L. Abshire; P. A. Miller; T. W. Schlatter

1990-12-01T23:59:59.000Z

143

Structural Design of a Horizontal-Axis Tidal Current Turbine...  

NLE Websites -- All DOE Office Websites (Extended Search)

M.J. Lawson, and Y. Li Presented at the ASME 30 th International Conference on Ocean, Offshore, and Arctic Engineering Rotterdam, The Netherlands June 19-24, 2011 Conference Paper...

144

Estimation of turbulence level and scale for wind turbine applications  

DOE Green Energy (OSTI)

A simplified method is presented for estimating onsite turbulence variance within the wind turbine layer for horizontal wind speed. The method is based principally on estimating the probability distribution of wind speed and assigning a variance to each mean wind speed based on surface roughness estimates. The model is not proposed as an alternative to onsite measurement and analysis, but rather as an adjunct to such a program. A revision of the Kaimal neutral u-component spectrum is suggested to apply to the mix of the stabilities occurring during operational winds. Values of integral length scale calculated from data analysis are shown to contradict the length scale model implicit in turbulence power spectra. Also, these calculated values are shown to be extremely sensitive to the length of the time series and the detrending method used. The analysis and modeling are extended to the rotational frame of reference for a horizontal-axis wind turbine by modeling the ratios of harmonic spike variances (1P, 2P, etc.) in the rotational spectrum to the Eulerian turbulence variance. 15 refs., 11 figs., 3 tabs.

Powell, D.C.

1988-11-01T23:59:59.000Z

145

Low-Maintenance Wind Power System  

E-Print Network (OSTI)

with widespread adoption of wind energy. The project hasProject: Low-Maintenance Wind Power System Summary of theImproved Vertical Axis Wind Turbine and Aerodynamic Control

Rasson, Joseph E

2010-01-01T23:59:59.000Z

146

Full-scale wind turbine rotor aerodynamics research  

DOE Green Energy (OSTI)

The United States Department of Energy and the National Renewable Energy Laboratory (NREL) are conducting research to improve wind turbine technology at the NREL National Wind Technology Center (NWTC). One program, the Combined Experiment, has focused on making measurements needed to understand aerodynamic and structural responses of horizontal-axis wind turbines (HAWT). A new phase of this program, the Unsteady Aerodynamics Experiment, will focus on quantifying unsteady aerodynamic phenomena prevalent in stall-controlled HAWTs. Optimally twisted blades and innovative instrumentation and data acquisition systems will be used in these tests. Data can now be acquired and viewed interactively during turbine operations. This paper describes the NREL Unsteady Aerodynamics Experiment and highlights planned future research activities.

Simms, D A; Butterfield, C P

1994-11-01T23:59:59.000Z

147

Quiet airfoils for small and large wind turbines  

DOE Patents (OSTI)

Thick airfoil families with desirable aerodynamic performance with minimal airfoil induced noise. The airfoil families are suitable for a variety of wind turbine designs and are particularly well-suited for use with horizontal axis wind turbines (HAWTs) with constant or variable speed using pitch and/or stall control. In exemplary embodiments, a first family of three thick airfoils is provided for use with small wind turbines and second family of three thick airfoils is provided for use with very large machines, e.g., an airfoil defined for each of three blade radial stations or blade portions defined along the length of a blade. Each of the families is designed to provide a high maximum lift coefficient or high lift, to exhibit docile stalls, to be relatively insensitive to roughness, and to achieve a low profile drag.

Tangler, James L. (Boulder, CO); Somers, Dan L. (Port Matilda, PA)

2012-06-12T23:59:59.000Z

148

Control of Wind Turbines: Past, Present, and Future  

Science Conference Proceedings (OSTI)

We review the objectives and techniques used in the control of horizontal axis wind turbines at the individual turbine level, where controls are applied to the turbine blade pitch and generator. The turbine system is modeled as a flexible structure operating in the presence of turbulent wind disturbances. Some overview of the various stages of turbine operation and control strategies used to maximize energy capture in below rated wind speeds is given, but emphasis is on control to alleviate loads when the turbine is operating at maximum power. After reviewing basic turbine control objectives, we provide an overview of the common basic linear control approaches and then describe more advanced control architectures and why they may provide significant advantages.

Laks, J. H.; Pao, L. Y.; Wright, A. D.

2009-01-01T23:59:59.000Z

149

On Computing the Surface Horizontal Pressure Gradient over Elevated Terrain  

Science Conference Proceedings (OSTI)

Methods are proposed for calculating the surface horizontal pressure gradient or geostrophic wind in a local area over elevated terrain from randomly spaced surface observations. These procedures avoid many of the problems associated with sea-...

Maurice Danard

1989-06-01T23:59:59.000Z

150

Horizontal Divergence Associated with Zonally Isolated Jet Streams  

Science Conference Proceedings (OSTI)

Horizontal divergence in the upper troposphere associated with zonally isolated jet streams in the climatological-mean fold for the Northern Hemisphere winter is examined by using the wind fields obtained from the NMC operational analyses in the ...

Hisashi Nakamura

1993-07-01T23:59:59.000Z

151

A comparison of measured wind park load histories with the WISPER and WISPERX load spectra  

DOE Green Energy (OSTI)

The blade-loading histories from two adjacent Micon 65/13 wind turbines are compared with the variable-amplitude test-loading histories known as the WISPER and WISPERX spectra. These standardized loading sequences were developed from blade flapwise load histories taken from nine different horizontal-axis wind turbines operating under a wide range of conditions in Europe. The subject turbines covered a broad spectrum of rotor diameters, materials, and operating environments. The final loading sequences were developed as a joint effort of thirteen different European organizations. The goal was to develop a meaningful loading standard for horizontal-axis wind turbine blades that represents common interaction effects seen in service. In 1990, NREL made extensive load measurements on two adjacent Micon 65/13 wind turbines in simultaneous operation in the very turbulent environment of a large wind park. Further, before and during the collection of the loads data, comprehensive measurements of the statistics of the turbulent environment were obtained at both the turbines under test and at two other locations within the park. The trend to larger but lighter wind turbine structures has made an understanding of the expected lifetime loading history of paramount importance. Experience in the US has shown that the turbulence-induced loads associated with multi-row wind parks in general are much more severe than for turbines operating individually or within widely spaced environments. Multi-row wind parks are much more common in the US than in Europe. In this paper we report on our results in applying the methodology utilized to develop the WISPER and WISPERX standardized loading sequences using the available data from the Micon turbines. While the intended purpose of the WISPER sequences were not to represent a specific operating environment, we believe the exercise is useful, especially when a turbine design is likely to be installed in a multi-row wind park.

Kelley, N.D.

1995-01-01T23:59:59.000Z

152

Wind energy conversion. Volume IX. Aerodynamics of wind turbine with tower disturbances  

DOE Green Energy (OSTI)

Lifting line theory which is the counterpart of Prandtl's lifting line theory for rotating wing is employed for the overall performance analysis of a horizontal axis wind turbine rotor operating in a uniform flow. The wake system is modeled by non-rigid wake which includes the radial expansion and the axial retardation of trailing vortices. For the non-uniform flow which are caused by the ground, the tower reflection, or the tower shadow, the unsteady airloads acting on the turbine blade are computed, using lifting line theory and a non-rigid wake model. An equation which gives the wind profile in the tower shadow region is developed. Also, the equations to determine pitch angle control are derived to minimize the flapping moment variations or the thrust variations due to the non-uniform flow over a rotation.

Chung, S.Y.

1978-09-01T23:59:59.000Z

153

Experimental and analytical research on the aerodynamics of wind driven turbines. Final report  

DOE Green Energy (OSTI)

The successful development of reliable, cost competitive horizontal axis, propeller-type wind energy conversion systems (WECS) is strongly dependent on the availability of advanced technology for each of the system components. This aerodynamic research program was aimed at providing a reliable, comprehensive data base on a series of wind turbine models covering a broad range of the prime aerodynamic and geometric variables. Such data obtained under controlled laboratory conditions on turbines designed by the same method, of the same size, and tested in the same wind tunnel had not been available in the literature. Moreover, this research program was further aimed at providing a basis for evaluating the adequacy of existing wind turbine aerodynamic design and performance methodology, for assessing the potential of recent advanced theories and for providing a basis for further method development and refinement.

Rohrbach, C.; Wainauski, H.; Worobel, R.

1977-12-01T23:59:59.000Z

154

Control system for a vertical axis windmill  

DOE Patents (OSTI)

A vertical axis windmill having a rotating structure is provided with a series of articulated vertical blades whose positions are controlled to maintain a constant RPM for the rotating structure, when wind speed is sufficient. A microprocessor controller is used to process information on wind speed, wind direction and RPM of the rotating structure to develop an electrical signal for establishing blade position. The preferred embodiment of the invention, when connected to a utility grid, is designed to generate 40 kilowatts of power when exposed to a 20 mile per hour wind. The control system for the windmill includes electrical blade actuators that modulate the blades of the rotating structure. Blade modulation controls the blade angle of attack, which in turn controls the RPM of the rotor. In the preferred embodiment, the microprocessor controller provides the operation logic and control functions. A wind speed sensor provides inputs to start or stop the windmill, and a wind direction sensor is used to keep the blade flip region at 90.degree. and 270.degree. to the wind. The control system is designed to maintain constant rotor RPM when wind speed is between 10 and 40 miles per hour.

Brulle, Robert V. (St. Louis County, MO)

1983-10-18T23:59:59.000Z

155

The Precision and Relative Accuracy of Profiler Wind Measurements  

Science Conference Proceedings (OSTI)

Two independent wind profiles were measured every hour during February 1986 with a five-beam, UHF (405 MHz) wind Profiler at Platteville, Colorado. Our analysis of the horizontal wind components over all heights for the entire month gave a ...

R. G. Strauch; B. L. Weber; A. S. Frisch; C. G. Little; D. A. Merritt; K. P. Moran; D. C. Welsh

1987-12-01T23:59:59.000Z

156

An Algorithm for the Detection of Fronts in Wind Profiler Data  

Science Conference Proceedings (OSTI)

An algorithm to detect frontal zones in time–height cross sections of horizontal wind from wind profiler measurements is described. The algorithm works by identifying regions with 1) a strong horizontal temperature gradient, estimated by using a ...

Christopher Lucas; Peter T. May; Robert A. Vincent

2001-04-01T23:59:59.000Z

157

Availability of wind power  

DOE Green Energy (OSTI)

Meteorological studies of available wind power were begun at Sandia in 1973 to support the development of a vertical-axis wind turbine (VAWT, ''egg-beater''). This presentation reviews work to date. Copies of seven source reports were provided to ELETROBRAS; Scientia, Ltda., has included them in an extensive bibliography that was distributed at the seminar. This report summarizes those climatological studies that are needed to assist and promote wind energy exploitation in Brazil.

Reed, J.W.

1978-01-01T23:59:59.000Z

158

Horizontal Plate Plate  

NLE Websites -- All DOE Office Websites (Extended Search)

Horizontal Plate Plate Horizontal Plate Plate Metadata also available as Metadata: Identification_Information Data_Quality_Information Spatial_Data_Organization_Information Spatial_Reference_Information Entity_and_Attribute_Information Distribution_Information Metadata_Reference_Information Identification_Information: Citation: Citation_Information: Originator: Ray George Publication_Date: Unknown Title: Horizontal Plate Plate Geospatial_Data_Presentation_Form: vector digital data Online_Linkage: Description: Abstract: Monthly and annual average solar resource potential for the lower 48 states Purpose: Provide information on the solar resource potential for the lower 48

159

Dynamic stall of small wind systems  

SciTech Connect

Aerospace Systems, Inc. (ASI) conducted a study of dynamic stall in order to define its influence on the airfoil force and moment coefficients so that these effects can be included in the calculation of small wind energy conversion system (SWECS) loads and response. The effort includes a review of past work to determine its applicability to SWECS requirements, a definition of a dynamic stall theory for use in SWECS design, and computer implementation of the theory in SWECS loads and dynamic response analyses. Sample calculations are made for representative vertical-axis (VAWT) and horizontal-axis (HAWT) wind turbines. The basic results for the fixed-pitch HAWT show that dynamic stall effects may increase normal loads and moments by about ten percent. For the cyclic pitch VAWT, the peak normal load may be slightly underestimated but the peak moment may be significantly underestimated. The consequences of dynamic stall may be a change in performance with resultant mismatch of selected components or a reduction in the fatigue life of the SWECS structure. Semiempirical methods are used for the practical estimation of the forces and moments on oscillating airfoils or airfoils in an oscillating airstream. The dynamic stall method presented in this report is applicable primarily to large amplitude oscillations of the airfoil. Fully-developed dynamic stall is presumed and, therefore, the method may not be adequate for predicting aerodynamic loads and moments for incipient or light stall.

Noll, R.B.; Ham, N.D.

1983-02-01T23:59:59.000Z

160

Nonlinear Horizontal Diffusion for GCMs  

Science Conference Proceedings (OSTI)

The mixing-length-based parameterization of horizontal diffusion, which was originally proposed by Smagorinsky, is revisited. The complete tendencies of horizontal momentum diffusion, the associated frictional heating, and horizontal diffusion of ...

Erich Becker; Ulrike Burkhardt

2007-04-01T23:59:59.000Z

Note: This page contains sample records for the topic "horizontal axis wind" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

In-field use of laser Doppler vibrometer on a wind turbine blade  

DOE Green Energy (OSTI)

One of our primary goals was to determine how well a laser Doppler vibrometer (LDV) could measure the structural dynamic response of a wind turbine that was parked in the field. We performed a series of preliminary tests in the lab to determine the basic limitations of the LDV for this application. We then instrumented an installed parked horizontal axis wind turbine with accelerometers to determine the natural frequencies, damping, and mode shapes of the wind turbine and rotor as a baseline for the LDV and our other tests. We also wanted to determine if LDV modal information could be obtained from a naturally (wind) excited wind turbine. We compared concurrently obtained accelerometer and LDV data in an attempt to assess the quality of the LDV data. Our test results indicate the LDV can be successfully used in the field environment of an installed wind turbine, but with a few restrictions. We were successful in obtaining modal information from a naturally (wind) excited wind turbine in the field, but the data analysis requires a large number of averaged data sets to obtain reasonable results. An ultimate goal of this continuing project is to develop a technique that will monitor the health of a structure, detect damage, and hopefully predict an impending component failure.

Rumsey, M.; Hurtado, J.; Hansche, B. [and others

1998-12-31T23:59:59.000Z

162

Tropical Cyclone Wind Retrievals from the Advanced Microwave Sounding Unit: Application to Surface Wind Analysis  

Science Conference Proceedings (OSTI)

Horizontal winds at 850 hPa from tropical cyclones retrieved using the nonlinear balance equation, where the mass field was determined from Advanced Microwave Sounding Unit (AMSU) temperature soundings, are compared with the surface wind fields ...

Kotaro Bessho; Mark DeMaria; John A. Knaff

2006-03-01T23:59:59.000Z

163

Operation of a third generation wind turbine  

SciTech Connect

A modern wind turbine was installed on May 26, 1982, at the USDA Conservation and Production Research Laboratory, Bushland, Texas. This wind machine was used to provide electrical energy for irrigation pumping and other agricultural loads. The wind turbine purchased for this research is an Enertech Model 44, manufactured by Enertech Corporation, Norwich, Vermont. The horizontal-axis wind turbine has a 13.4 m diameter, three-bladed, fixed-pitch rotor on a 24.4-m tower. The blades are laminated epoxy-wood, and are attached to a steel hub. A 25-kW induction generator provides 240 V, 60 Hz, single-phase electrical power. The wind turbine operated 64 percent of the time, while being available to operate over 94 percent of the time. The unit had a net energy production of over 80,000 kWh in an average windspeed of 5.9 m/s at a height of 10 m in a 16-month period. The blade pitch was originally offset two degrees from design to maintain power production within the limitations of the gearbox, generator, and brakes. A maximum output of 23.2 kW averaged over a 15-second period indicated that with a new brake, the system was capable of handling more power. After a new brake was installed, the blade pitch was changed to one degree from design. The maximum power output measured after the pitch change was 29.3 kW. Modified blade tip brakes were installed on the wind turbine on July 7, 1983. These tip brakes increased power production at lower windspeeds while reducing power at higher windspeeds.

Vosper, F.C.; Clark, R.N.

1983-12-01T23:59:59.000Z

164

Probabilistic fatigue methodology and wind turbine reliability  

DOE Green Energy (OSTI)

Wind turbines subjected to highly irregular loadings due to wind, gravity, and gyroscopic effects are especially vulnerable to fatigue damage. The objective of this study is to develop and illustrate methods for the probabilistic analysis and design of fatigue-sensitive wind turbine components. A computer program (CYCLES) that estimates fatigue reliability of structural and mechanical components has been developed. A FORM/SORM analysis is used to compute failure probabilities and importance factors of the random variables. The limit state equation includes uncertainty in environmental loading, gross structural response, and local fatigue properties. Several techniques are shown to better study fatigue loads data. Common one-parameter models, such as the Rayleigh and exponential models are shown to produce dramatically different estimates of load distributions and fatigue damage. Improved fits may be achieved with the two-parameter Weibull model. High b values require better modeling of relatively large stress ranges; this is effectively done by matching at least two moments (Weibull) and better by matching still higher moments. For this purpose, a new, four-moment {open_quotes}generalized Weibull{close_quotes} model is introduced. Load and resistance factor design (LRFD) methodology for design against fatigue is proposed and demonstrated using data from two horizontal-axis wind turbines. To estimate fatigue damage, wind turbine blade loads have been represented by their first three statistical moments across a range of wind conditions. Based on the moments {mu}{sub 1}{hor_ellipsis}{mu}{sub 3}, new {open_quotes}quadratic Weibull{close_quotes} load distribution models are introduced. The fatigue reliability is found to be notably affected by the choice of load distribution model.

Lange, C.H. [Stanford Univ., CA (United States)

1996-05-01T23:59:59.000Z

165

NREL: Wind Research - Viryd Technologies' CS8 Turbine Testing and Results  

NLE Websites -- All DOE Office Websites (Extended Search)

Viryd Technologies' CS8 Turbine Testing and Results Viryd Technologies' CS8 Turbine Testing and Results Viryd Technologies CS8 wind turbine. Text Version As part of the National Renewable Energy Laboratory and U.S. Department of Energy (NREL/DOE) Independent Testing project, NREL is testing Viryd Technologies' CS8 small wind turbine at the National Wind Technology Center (NWTC). The CS8 is an upwind, horizontal-axis, three-bladed, stall controlled turbine rated at 8 kilowatts (kW). It has an 8.5-meter rotor diameter and is mounted on a guyed tilt-up lattice tower with a hub height of 24.9 meters. The CS8 uses a single-phase, grid-connected, induction generator that operates at 240 volts AC. Testing Summary Supporting data and explanations for data included in this table are provided in the final reports.

166

Horizontal Advanced Tensiometer  

DOE Patents (OSTI)

An horizontal advanced tensiometer is described that allows the monitoring of the water pressure of soil positions, particularly beneath objects or materials that inhibit the use of previous monitoring wells. The tensiometer includes a porous cup, a pressure transducer (with an attached gasket device), an adaptive chamber, at least one outer guide tube which allows access to the desired horizontal position, a transducer wire, a data logger and preferably an inner guide tube and a specialized joint which provides pressure on the inner guide tube to maintain the seal between the gasket of the transducer and the adaptive chamber.

Hubbell, Joel M.; Sisson, James B.

2004-06-22T23:59:59.000Z

167

Maintenance and operation of a small wind generator in the marine environment. Final report  

SciTech Connect

This report discusses the maintenance and operation of a wind-turbine generator that has been undergoing tests as a source of energy for remote Coast Guard lighthouses. The report documents both the effects of operating the wind machine in the marine environment and the maintenance that it required. Design parameters and performance records of the generator are also evaluated. The HR2 is a horizontal-axis, upwind-oriented, three-bladed wind machine. It is equipped with a direct-drive system that allows the kinetic force captured by the propeller to be converted directly into rotational force driving the main shaft. The HR2 alternator and blade/hub system are allowed to tilt out of a near-vertical plane about a shaft and bearing mechanism. The VARCS is a torsion spring- and hinge-mechanism that acts against the lifting dynamics of the spinning blades. As high winds or gusts tilt the alternator about the hinge, the VARCS's spring opposes this force and regulates the blades angle of attack into the wind; the propeller's RPM drop when tilted because of the feathering action. If the wind subsides, the force of the VARCS spring drives the alternator assembly down and presents the blades back into the wind.

Heerlein, W.

1986-07-01T23:59:59.000Z

168

A Method for Estimating the Standard Deviation of Wind Directions  

Science Conference Proceedings (OSTI)

A method for estimating the standard deviation of horizontal wind directions (??), from the cosines and sines of direction angles, is proposed.

K. A. Verrall; R. L. Williams

1982-12-01T23:59:59.000Z

169

An Evaluation of Two NEXRAD Wind Retrieval Methodologies and Their Use in Atmospheric Dispersion Models  

Science Conference Proceedings (OSTI)

Two entirely different methods for retrieving 3D fields of horizontal winds from Next Generation Weather Radar (NEXRAD) radial velocities have been evaluated using radar wind profiler measurements to determine whether routine wind retrievals ...

Jerome D. Fast; Rob K. Newsom; K. Jerry Allwine; Qin Xu; Pengfei Zhang; Jeffrey Copeland; Juanzhen Sun

2008-09-01T23:59:59.000Z

170

Enertech 15-kW wind-system development: Phase I. Design and analysis. Volume I. Executive summary  

Science Conference Proceedings (OSTI)

A utility interfaced wind machine rated for 15 kW at 9 m/s (20.1 mph) has been designed to be cost effective in 5.4 m/s (12 mph) average wind sites. Approximately 18 months into the research and development program a completed design meeting contract specifications was submitted to the buyer. The design is for a horizontal axis, down wind machine which features three fixed pitch wood-epoxy blades and free yaw. Rotor diameter is 44 feet (13.4 meters). Unit shutdown is provided by an electrohydraulic brake. Blade tip brakes provide back-up rotor overspeed protection. Design merits have been verified through dynamic truck testing of a prototype unit.

Not Available

1981-09-01T23:59:59.000Z

171

Enertech 15-kW wind-system development. Phase I. Design and Analysis. Volume II. Technical report  

SciTech Connect

A utility interfaced wind machine rated for 15 kW at 9 m/s (20.1 mph) has been designed to be cost effective in 5.4 m/s (12 mph) average wind sites. Approximately 18 months into the research and development program a completed design meeting contract specifications was submitted to the buyer. The design is for a horizontal axis, down wind machine which features three fixed pitch wood-epoxy blades and free yaw. Rotor diameter is 44 feet (13.4 meters). Unit shutdown is provided by an electrohydraulic brake. Blade tip brakes provide back-up rotor overspeed protection. Design merits have been verified through dynamic truck testing of a prototype unit.

Dodge, D.M. (ed.)

1981-09-01T23:59:59.000Z

172

Development of a 2-kilowatt high-reliability wind machine. Phase I. Design and analysis. Volume II. Technical report  

Science Conference Proceedings (OSTI)

A high reliability wind machine rated for 2 kW at 9 m/s has been designed to be cost-effective for remote site use. To meet or exceed environmental conditions as specified in Contract PF64410F, the resulting design defines a rugged, relatively simple wind machine. Rigorous fatigue analysis for structural components and development of redundant systems for electrical components led to an expected mean time between failures of 12.35 years. Approximately one year into the research and development program a completed design meeting contract stipulations is being submitted to the contract buyer. The design is for a horizontal axis, down-wind machine with two wooden blades spanning 5 meters diameter. Positive rotor speed control is accomplished through a centrifugally governed variable pitch stalling rotor. Design merits have been confirmed through dynamic truck testing.

Drake, W.; Clews, H.; Cordes, J.; Johnson, B.; Murphy, P.

1980-01-01T23:59:59.000Z

173

Development of a 2-kilowatt high-reliability wind machine. Phase I. Design and analysis. Volume I. Executive summary  

Science Conference Proceedings (OSTI)

A high reliability wind machine rated for 2 kW at 9 m/s has been designed to be cost-effective for remote site use. To meet or exceed environmental conditions as specified in Contract PF64410F, the resulting design defines a rugged, relatively simple wind machine. Rigorous fatigue analysis for structural components and development of redundant systems for electrical components led to an expected mean time between failures of 12.35 years. Approximately one year into the research and development program, a completed design meeting contract stipulations is being submitted to the contract buyer. The design is for a horizontal axis, down-wind machine with two wooden blades spanning 5 meters diameter. Positive rotor speed control is accomplished through a centrifugally governed variable pitch, stalling rotor. Design merits have been confirmed through dynamic truck testing.

Drake, W.; Clews, H.; Cordes, J.; Johnson, B.; Murphy, P.

1980-01-01T23:59:59.000Z

174

Cementing horizontal wells  

SciTech Connect

Since the introduction of horizontal drilling, most completions have been open hole. Open-hole or slotted-liner completions may be satisfactory in straight, thick formations, if stimulation is not required. But if the wellbore wanders out of the reservoir, whether due to loss of directional control or spotty knowledge of formation dimensions, casing becomes a necessity. In addition, a wellbore that stays in the formation but comes uncomfortably close to the water-oil contact or gas cap requires casing to prevent coning. Further, if stimulation is anticipated, or may become a necessity, it is essential that the hole be cased and cemented. Otherwise, there is no control of the stimulation treatment. Even if the horizontal wellbore itself does not require casing, intermediate casing in the high-angle hole is needed. This is especially critical in open-hole completions below a gas cap, for example. The keys to effective horizontal cementing are fundamentally the same as for cementing vertical wells: proper centralization of casing in the bore-hole to ensure efficient mud removal and well-designed cement slurries.

Baret, F.; Griffin, T.J.

1989-05-01T23:59:59.000Z

175

Measurement of turbulent wind velocities using a rotating boom apparatus  

DOE Green Energy (OSTI)

The present report covers both the development of a rotating-boom facility and the evaluation of the spectral energy of the turbulence measured relative to the rotating boom. The rotating boom is composed of a helicopter blade driven through a pulley speed reducer by a variable speed motor. The boom is mounted on a semiportable tower that can be raised to provide various ratios of hub height to rotor diameter. The boom can be mounted to rotate in either the vertical or horizontal plane. Probes that measure the three components of turbulence can be mounted at any location along the radius of the boom. Special hot-film sensors measured two components of the turbulence at a point directly in front of the rotating blade. By using the probe rotated 90/sup 0/ about its axis, the third turbulent velocity component was measured. Evaluation of the spectral energy distributions for the three components of velocity indicates a large concentration of energy at the rotational frequency. At frequencies slightly below the rotational frequency, the spectral energy is greatly reduced over that measured for the nonrotating case measurements. Peaks in the energy at frequencies that are multiples of the rotation frequency were also observed. We conclude that the rotating boom apparatus is suitable and ready to be used in experiments for developing and testing sensors for rotational measurement of wind velocity from wind turbine rotors. It also can be used to accurately measure turbulent wind for testing theories of rotationally sampled wind velocity.

Sandborn, V.A.; Connell, J.R.

1984-04-01T23:59:59.000Z

176

Three Types of Horizontal Vortices Observed in Wildland Mass and Crown Fires  

Science Conference Proceedings (OSTI)

Observation shows that three types of horizontal vortices may form during intense wildland fires. Two of these vortices are longitudinal relative to the ambient wind and the third is transverse. One of the longitudinal types, a vortex pair, ...

Donald A. Haines; Mahlon C. Smith

1987-12-01T23:59:59.000Z

177

Measurement in a wind tunnel of the modification of mean wind and turbulence characteristics due to induction effects near wind turbine rotors  

DOE Green Energy (OSTI)

It is the purpose of this report to provide experimental data on the wind field surrounding a single model wind turbine rotor disk. These data should provide an improved physical insight into the induction effects of the air flow as it approaches the wind turbine. This insight should in turn improve an analytical model's predictive capabilities. A scaled model of a horizontal-axis wind turbine (a two-bladed rotor of diameter 53 cm) was placed into the Meteorological Wind Tunnel (MWT) facility at Colorado State University (cross-section width of 183 cm). Four different approach flow conditions were studied: low and moderate turbulence levels (0.1% and 1.5% intensity) at both 6 and 7.6 m/s freestream air velocities. For each of these flow conditions the rotor power coefficient versus tip speed ratio was obtained, and the 3-dimensional velocity field from 3 rotor diameters upwind to 0.5 diameter downwind was tabulated. The power output of the rotor was obtained via a simple prony brake friction device that imparts a torque (measured by the deflection of a spring) to the spinning shaft of the wind turbine. The rotor speed, measured by a strobe light, was observed to vary with load from 900 rpm up to 2100 rpm for the flow conditions described above. The 3-dimensional velocity field was measured via a three-hot-film probe. Details of the measurement techniques are provided. The test program and data results are also given. A short discussion of the implications of this data set is included. 12 refs., 19 figs., 11 tabs.

Neff, D.E.; Meroney, R.N.

1987-08-01T23:59:59.000Z

178

Numerical and Laboratory Study of a Horizontally Evolving Convective Boundary Layer. Part I: Transition Regimes and Development of the Mixed Layer  

Science Conference Proceedings (OSTI)

Results are presented from a large eddy simulation (LES) and wind tunnel study of the turbulence regime in a horizontally evolving sheared atmospheric convective boundary layer (CBL) capped by a temperature inversion. The wind tunnel part of the ...

E. Fedorovich; F. T. M. Nieuwstadt; R. Kaiser

2001-01-01T23:59:59.000Z

179

Wind turbine spoiler  

DOE Patents (OSTI)

An aerodynamic spoiler system for a vertical axis wind turbine includes spoilers on the blades initially stored near the rotor axis to minimize drag. A solenoid latch adjacent the central support tower releases the spoilers and centrifugal force causes the spoilers to move up the turbine blades away from the rotor axis, thereby producing a braking effect and actual slowing of the associated wind turbine, if desired. The spoiler system can also be used as an infinitely variable power control by regulated movement of the spoilers on the blades over the range between the undeployed and fully deployed positions. This is done by the use of a suitable powered reel and cable located at the rotor tower to move the spoilers.

Sullivan, William N. (Albuquerque, NM)

1985-01-01T23:59:59.000Z

180

Systematic Controller Design Methodology for Variable-Speed Wind Turbines  

DOE Green Energy (OSTI)

Variable-speed, horizontal axis wind turbines use blade-pitch control to meet specified objectives for three operational regions. This paper provides a guide for controller design for the constant power production regime. A simple, rigid, non-linear turbine model was used to systematically perform trade-off studies between two performance metrics. Minimization of both the deviation of the rotor speed from the desired speed and the motion of the actuator is desired. The robust nature of the proportional-integral-derivative controller is illustrated, and optimal operating conditions are determined. Because numerous simulation runs may be completed in a short time, the relationship between the two opposing metrics is easily visualized.

Hand, M. M.; Balas, M. J.

2002-02-01T23:59:59.000Z

Note: This page contains sample records for the topic "horizontal axis wind" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

NREL: Wind Research Home Page  

NLE Websites -- All DOE Office Websites (Extended Search)

Photo of the non-torque loading system at the National Wind Technology Center. Photo of the non-torque loading system at the National Wind Technology Center. New NWTC Test Facility to Improve Wind Turbines Testing the performance of multimegawatt wind turbine drivetrains Illustration showing mountains, several wind turbines, a power plant, a crane setting up a turbine blade, and two semi-trucks carrying turbine blades. The concept is to show all the pieces and parts of a complete wind energy system and how they work together. NWTC Systems Engineering Initiative Analysis Platform New platform helps analyze and integrate entire wind energy systems Short video featuring Fort Felker, Center Director of the National Wind Technology Center, highlighting the NWTC's dual-axis resonant blade testing capabilities. Images from this video include Fort speaking, the static turbine blade in the testing facility, and flapwise and edgewise testing in action.

182

Improved Wind Measurements on Research Aircraft  

Science Conference Proceedings (OSTI)

Improved techniques for measuring horizontal and vertical wind components and state variables on research aircraft are presented. They include a filtering method for correcting ground speed and position Inertial Navigation System data with Global ...

D. Khelif; S. P. Burns; C. A. Friehe

1999-07-01T23:59:59.000Z

183

HORIZONTAL BOILING REACTOR SYSTEM  

DOE Patents (OSTI)

Reactors of the boiling water type are described wherein water serves both as the moderator and coolant. The reactor system consists essentially of a horizontal pressure vessel divided into two compartments by a weir, a thermal neutronic reactor core having vertical coolant passages and designed to use water as a moderator-coolant posltioned in one compartment, means for removing live steam from the other compartment and means for conveying feed-water and water from the steam compartment to the reactor compartment. The system further includes auxiliary apparatus to utilize the steam for driving a turbine and returning the condensate to the feed-water inlet of the reactor. The entire system is designed so that the reactor is self-regulating and has self-limiting power and self-limiting pressure features.

Treshow, M.

1958-11-18T23:59:59.000Z

184

Control system for a vertical-axis windmill  

DOE Patents (OSTI)

A vertical-axis windmill having a rotating structure is provided with a series of articulated vertical blades whose positions are controlled to maintain a constant RPM for the rotating structure, when wind speed is sufficient. A microprocessor controller is used to process information on wind speed, wind direction and RPM of the rotating structure to develop an electrical signal for establishing blade position. The preferred embodiment of the invention, when connected to a utility grid, is designed to generate 40 kilowatts of power when exposed to a 20 mile per hour wind. The control system for the windmill includes electrical blade actuators that modulate the blades of the rotating structure. Blade modulation controls the blade angle of attack, which in turn controls the RPM of the rotor. In the preferred embodiment, the microprocessor controller provides the operation logic and control functions. A wind speed sensor provides inputs to start or stop the windmill, and a wind direction sensor is used to keep the blade flip region at 90 and 270/sup 0/ to the wind. The control system is designed to maintain constant rotor RPM when wind speed is between 10 and 40 miles per hour.

Brulle, R.V.

1981-09-03T23:59:59.000Z

185

Analysis of the Madaras Rotor Power Plant: an alternate method for extracting large amounts of power from the wind. Executive summary  

DOE Green Energy (OSTI)

The purpose of the program was to analyze and up-date the design of the Madaras Rotor Power Plant concept that had been developed in the 1930's to determine the technical and economic feasibility of this system to be competitive with conventional horizontal axis wind turbines. The Madaras concept uses rotating cylinders, vertically mounted on flat cars, to react with the wind like a sail and propel an endless train of connected cars around a closed track at constant speed. Electricity is generated by alternators on each car that are geared to the wheels. Electrical power is transmitted from each car to the power house by a trolley system. A four-task program consisting of a series of wind tunnel tests, an electro-mechanical analysis, a performance analysis, and a cost analysis was conducted.

Whitford, D.H.; Minardi, J.E.; West, B.S.; Dominic, R.J.

1978-06-01T23:59:59.000Z

186

Wake of the MOD-0A1 wind turbine at two rotor diameters downwind on December 3, 1981  

DOE Green Energy (OSTI)

The wake of the MOD-0A1 wind turbine at Clayton, New Mexico has been measured using a vertical plane array of anemometers in a crosswind plane at a distance of two rotor diameters directly downwind of the turbine. Rotor blade vortices were well mixed into the wake turbulence and were not separately detectable. Wake swirl about the along-wind axis had a value not greater than 0.025 rad/s. Extra turbulence energy existed in the edge of the wake at a frequency of about n=0.025 Hz. The cross-wake plane analyses of wind speeds revealed a nearly circular inner portion and a strongly elliptical portion. The elliptical portion major axis was horizontal. An estimate of the average rate of reenergizing of the wake, using measurements of mean wind energy flow and turbine power, suggests that entrainment with ambient air may have been rapid. Some wake characteristics were compared with the corresponding ones for several simple wake models based upon concepts of mixing of ambient air into a wake or an equivalent coaxial jet. (LEW)

Connell, J.R.; George, R.L.

1982-11-01T23:59:59.000Z

187

Two-axis tracking solar collector mechanism  

DOE Green Energy (OSTI)

This invention is a novel solar tracking mechanism incorporating a number of practical features that give it superior environmental resilience and exceptional tracking accuracy. The mechanism comprises a lightweight space-frame assembly supporting an array of point-focus Fresnel lenses in a two-axis tracking structure. The system is enclosed under a glass cover which isolates it from environmental exposure and enhances tracking accuracy by eliminating wind loading. Tracking accuracy is also enhanced by the system's broad-based tracking support. The system's primary intended application would be to focus highly concentrated sunlight into optical fibers for transmission to core building illumination zones, and the system may also have potential for photovoltaic or photothermal solar energy conversion.

Johnson, Kenneth C. (201 W. California Ave., #401, Sunnyvale, CA 94086)

1990-01-01T23:59:59.000Z

188

Two-axis tracking solar collector mechanism  

DOE Green Energy (OSTI)

This invention is a novel solar tracking mechanism incorporating a number of practical features that give it superior environmental resilience and exceptional tracking accuracy. The mechanism comprises a lightweight space-frame assembly supporting an array of point-focus Fresnel lenses in a two-axis tracking structure. The system is enclosed under a glass cover which isolates it from environmental exposure and enhances tracking accuracy by eliminating wind loading. Tracking accuracy is also enhanced by the system's broad-based tracking support. The system's primary intended application would be to focus highly concentrated sunlight into optical fibers for transmission to core building illumination zones, and the system may also have potential for photovoltaic or photothermal solar energy conversion.

Johnson, Kenneth C. (201 W. California Ave. #705, Sunnyvale, CA 94086)

1992-01-01T23:59:59.000Z

189

Two-axis tracking solar collector mechanism  

DOE Patents (OSTI)

This invention is a novel solar tracking mechanism incorporating a number of practical features that give it superior environmental resilience and exceptional tracking accuracy. The mechanism comprises a lightweight space-frame assembly supporting an array of point-focus Fresnel lenses in a two-axis tracking structure. The system is enclosed under a glass cover which isolates it from environmental exposure and enhances tracking accuracy by eliminating wind loading. Tracking accuracy is also enhanced by the system's broad-based tracking support. The system's primary intended application would be to focus highly concentrated sunlight into optical fibers for transmission to core building illumination zones, and the system may also have potential for photovoltaic or photothermal solar energy conversion.

Johnson, Kenneth C. (201 W. California Ave., #401, Sunnyvale, CA 94086)

1990-01-01T23:59:59.000Z

190

Two-axis tracking solar collector mechanism  

DOE Patents (OSTI)

This invention is a novel solar tracking mechanism incorporating a number of practical features that give it superior environmental resilience and exceptional tracking accuracy. The mechanism comprises a lightweight space-frame assembly supporting an array of point-focus Fresnel lenses in a two-axis tracking structure. The system is enclosed under a glass cover which isolates it from environmental exposure and enhances tracking accuracy by eliminating wind loading. Tracking accuracy is also enhanced by the system's broad-based tracking support. The system's primary intended application would be to focus highly concentrated sunlight into optical fibers for transmission to core building illumination zones, and the system may also have potential for photovoltaic or photothermal solar energy conversion.

Johnson, Kenneth C. (201 W. California Ave. #705, Sunnyvale, CA 94086)

1992-01-01T23:59:59.000Z

191

Two-axis tracking solar collector mechanism  

DOE Patents (OSTI)

This invention is a novel solar tracking mechanism incorporating a number of practical features that give it superior environmental resilience and exceptional tracking accuracy. The mechanism comprises a lightweight space-frame assembly supporting an array of point-focus Fresnel lenses in a two-axis tracking structure. The system is enclosed under a glass cover which isolates it from environmental exposure and enhances tracking accuracy by eliminating wind loading. Tracking accuracy is also enhanced by the system's broad-based tracking support. The system's primary intended application would be to focus highly concentrated sunlight into optical fibers for transmission to core building illumination zones, and the system may also have potential for photovoltaic or photothermal solar energy conversion. 16 figs.

Johnson, K.C.

1992-12-08T23:59:59.000Z

192

NREL: Wind Research - Ventera's VT 10 Turbine Testing and Results  

NLE Websites -- All DOE Office Websites (Extended Search)

Ventera's VT 10 Turbine Testing and Results Ventera's VT 10 Turbine Testing and Results Ventera's VT10 wind turbine. Text Version As part of the National Renewable Energy Laboratory and U.S. Department of Energy (NREL/DOE) Independent Testing project, NREL is testing Ventera's VT10 small wind turbine at the National Wind Technology Center (NWTC). The VT10 is a horizontal-axis downwind, three-bladed turbine rated at 10 kilowatts (kW). Its diameter is 6.7 meters, and it is mounted on a lattice tower with a hub height of 21.7 meters. The VT10 uses a single-phase, grid-connected, permanent-magnet generator that operates at 240 volts AC. Testing Summary The summary of the tests is listed below, along with the final reports. Cumulative Energy Production 3/22/2010: 0; 3/29/2010: 26; 3/31/2010: 74; 4/1/2010: 75; 4/2/2010: 174;

193

Wind turbine trailing-edge aerodynamic brake design  

DOE Green Energy (OSTI)

This report describes the design of a centrifugally actuated aerodynamic-overspeed device for a horizontal-axis wind turbine. The device will meet the following criteria; (1) It will be effective for airfoil angles of attack 0{degrees} to 45{degrees}. (2) It will be stowed inside the blade profile prior to deployment. (3) It will be capable of offsetting the positive torque produced by the overall blade. (4) Hinge moments will be minimized to lower actuator loads and cost. (5) It will be evaluated as a potential power modulating active rotor-control system. A literature review of aerodynamic braking devices was conducted. Information from the literature review was used to conceptualize the most effective devices for subsequent testing and design. Wind-tunnel test data for several braking devices are presented in this report. Using the data for the most promising configuration, a preliminary design was developed for a MICON 65/13 wind turbine with Phoenix 7.9-m rotor blades.

Quandt, G.

1996-01-01T23:59:59.000Z

194

Application of a Bayesian Wind Profile Retrieval Technique to Radar Data Collected in the Alpine Southern Upslope Region and Comparison with Upstream Wind Profiler Measurements  

Science Conference Proceedings (OSTI)

In this paper, a new operational technique to retrieve the horizontal wind profile from Doppler radar measurements is used to carry out a statistical comparison of upslope and upstream wind profiles in the southern flank of the European Alps. The ...

P. Tabary; M. Petitdidier

2002-06-01T23:59:59.000Z

195

Fundamentals of horizontal well completions  

Science Conference Proceedings (OSTI)

Oil and gas wells are drilled horizontally for a variety of reasons, chiefly to improve production without drilling multiple vertical wells and to prevent water or gas coning. Benefits of horizontal drilling are well documented. This article addresses the fundamentals of completing a horizontal well, discussing completion by (1) open hole, (2) casing packers, (3) slotted or perforated liner, and (4) cemented casing/liner. Completion methods 1 through 3 are generally known as ''drain hole'' completions, and method 4 is commonly called the ''case hole'' or ''stimulated'' completion.

Austin, C.; Zimmerman, C.; Sullaway, B.; Sabins, F.

1988-05-01T23:59:59.000Z

196

Wind driven gas generator  

SciTech Connect

A means is provided to convert wind energy into electrical energy which, through electrolysis, forms gases to be stored under pressure, giving a form of stored energy for use at some future time by the use of a high torque, low speed vertical axis wind machine connected by direct drive to homopolar direct current generators so as to create direct current for the electrolysis of water, resulting in the breakdown of water into its basic components of hydrogen and oxygen, which are then stored under pressure until necessary for use as a source of energy.

Crehore, R.

1980-01-15T23:59:59.000Z

197

NREL: Wind Research - Mariah Power's Windspire Wind Turbine Testing and  

NLE Websites -- All DOE Office Websites (Extended Search)

Mariah Power's Windspire Wind Turbine Testing and Results Mariah Power's Windspire Wind Turbine Testing and Results A video of Mariah Power's Windspire wind turbine. Text Version As part of the National Renewable Energy Laboratory and U.S. Department of Energy (NREL/DOE) Independent Testing project, NREL tested Mariah Power's Windspire Giromill small wind turbine at the National Wind Technology Center (NWTC) through January 14, 2009 when NREL terminated its testing. Read a chronology of events and letter from Mariah Power to NREL. The Windspire is a 1.2-kilowatt (kW) vertical-axis small wind turbine. The turbine tower is 9.1 meters tall, and its rotor area is 1.2 by 6.1 meters. The turbine has a permanent-magnet generator with a single-phase output at 120 volts AC. Testing Summary Testing was terminated January 14, 2009. Published test reports include

198

A General Method for Fatigue Analysis of Vertical Axis  

E-Print Network (OSTI)

The fatigue life of wind turbine blades that are exposed to the random loading environment of atmospheric winds is described with random data analysis procedures. The incident wind speed and the stresses caused by these winds are expressed in terms of probability density functions, while the fatigue life vs stress level relationship is treated deterministically. This approach uses a "damage density function" to express fatigue damage as a function of wind speed. By examining the constraints on the variables in the damage density expression, some generalizations of the wind turbine fatigue problem are obtained. The area under the damage density function is inversely related to total fatigue life. Therefore, an increase in fatigue life caused by restricted operation in certain wind regimes is readily visualized. An "on parameter", which is the percentage of total time at each wind speed that the turbine actually operates, is introduced for this purpose. An example calculation is presented using data acquired from the DOE 100-kW turbine program. *This work was performed at Sandia National Laboratories and was supported by the US Department of Energy under Contract Number DE-AC04-76DP00789. Acknowledgments The calculations required to produce the figures in this paper would not have been possible without the work of Jerry McNerney and Tim Leonard in developing the AUTOSYM computer simulation, The efforts of Nolan Clark and Ron Davis in collecting data for the DOE 100-kW turbine at the USDA station in Bushland, TX are greatly appreciated. of Vertical Axis Wind Turbine Blades

Paul S. Veers

1983-01-01T23:59:59.000Z

199

Two-axis angular effector  

DOE Patents (OSTI)

A new class of coplanar two-axis angular effectors. These effectors combine a two-axis rotational joint analogous to a Cardan joint with linear actuators in a manner to produce a wider range of rotational motion about both axes defined by the joint. This new class of effectors also allows design of robotic manipulators having very high strength and efficiency. These effectors are particularly suited for remote operation in unknown surroundings, because of their extraordinary versatility. An immediate application is to the problems which arise in nuclear waste remediation.

Vaughn, Mark R. (Albuquerque, NM); Robinett, III, Rush D. (Tijeras, NM); Phelan, John R. (Albuquerque, NM); Van Zuiden, Don M. (Albuquerque, NM)

1997-01-21T23:59:59.000Z

200

Extreme Winds and Wind Effects on Structures  

Science Conference Proceedings (OSTI)

Extreme Winds and Wind Effects on Structures. The Engineering ... section. I. Extreme Winds: ... II. Wind Effects on Buildings. Database ...

2013-01-17T23:59:59.000Z

Note: This page contains sample records for the topic "horizontal axis wind" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Effect of winglets on a vertical-axis wind turbine.  

E-Print Network (OSTI)

??An helical rotor blade configuration, made of a NACA 0021 airfoil, is defined and three candidate winglets, characterized by a wingtip extension of 1.00 blade… (more)

Gasparoni, Lorenzo

2012-01-01T23:59:59.000Z

202

Estimator for the Standard Deviation of Wind Direction Based on Moments of the Cartesian Components  

Science Conference Proceedings (OSTI)

Mean and variance of horizontal wind direction are defined in a minimal variance sense. Starting from a theoretical model, termed anisotropic Gaussian model, of the probability density functions of the Cartesian wind components, the standard ...

Rudolf Weber

1991-09-01T23:59:59.000Z

203

A WRF Ensemble for Improved Wind Speed Forecasts at Turbine Height  

Science Conference Proceedings (OSTI)

The Weather Research and Forecasting Model (WRF) with 10-km horizontal grid spacing was used to explore improvements in wind speed forecasts at a typical wind turbine hub height (80 m). An ensemble consisting of WRF model simulations with ...

Adam J. Deppe; William A. Gallus Jr.; Eugene S. Takle

2013-02-01T23:59:59.000Z

204

On the Ability of the WRF Model to Reproduce the Surface Wind Direction over Complex Terrain  

Science Conference Proceedings (OSTI)

The ability of the Weather Research and Forecasting (WRF) model to reproduce the surface wind direction over complex terrain is examined. A simulation spanning a winter season at a high horizontal resolution of 2 km is compared with wind direction ...

Pedro A. Jiménez; Jimy Dudhia

2013-07-01T23:59:59.000Z

205

Anomalous Wind Circulation Observed during 1997/98 El Niño Using Indian MST Radar  

Science Conference Proceedings (OSTI)

Unique facility of measuring vertical winds using Indian mesosphere–stratosphere–troposphere (MST) radar along with horizontal winds enables the study of the atmospheric circulation over Gadanki, India. Several important features are noted while ...

V. V. M. Jagannadha Rao; A. Narendra Babu; S. Vijaya Bhaskara Rao; D. Narayana Rao

2007-01-01T23:59:59.000Z

206

Katabatic Winds on Ice Sheets: A Refinement of the Prandtl Model  

Science Conference Proceedings (OSTI)

Katabatic winds on ice sheets and glaciers are buoyancy-driven flows, much like turbidity currents in the ocean. These winds are driven by radiative cooling of the ice surface and are not resolved by the typical horizontal and vertical ...

R. J. Zammett; A. C. Fowler

2007-07-01T23:59:59.000Z

207

Adjoint-Method Retrievals of Low-Altitude Wind Fields from Single-Doppler Reflectivity and Radial-Wind Data  

Science Conference Proceedings (OSTI)

The simple adjoint (SA) method is extended to use both the reflectivity equation and the radial-wind equation to retrieve the low-altitude horizontal wind field from single-Doppler reflectivity and radial-wind data. Three extended methods are ...

Qin Xu; Chong-Jian Qiu

1995-10-01T23:59:59.000Z

208

WindPACT Rotor Design Study: Hybrid Tower Design; Period of Performance: 29 June 2000 -- 28 February 2004  

DOE Green Energy (OSTI)

The cost of a wind turbine tower can represent as much as 20% of the cost of an entire megawatt-scale horizontal axis wind turbine (HAWT) and as much as 10% of the total cost of energy. The tower is a major cost component, and its design is important: Its structural properties are key to the response of the rotor; its height determines the wind regime that the rotor experiences; it allows access to the turbine nacelle and rotor; and it houses components of the electrical connection and the control and protection systems. Most large wind turbines installed in the United States use self-supporting steel tubular towers. The diameter of these tubes is limited by the size that can be transported by road (approximately 4.3 m). The base dimensions of a truss tower are not restrained by this limit, but trusses may require more maintenance. Guyed tube towers have been used, but they represent additional foundation costs and inconvenience. Addressing these limitations may lead to an alternative that avoids the problems. For this reason, the WindPACT Rotor Design Study was modified to include a study of a hybrid tower to determine the technical and economic feasibility of such a design.

Malcolm, D. J.

2004-04-01T23:59:59.000Z

209

Methods and apparatus for cooling wind turbine generators  

DOE Patents (OSTI)

A wind turbine generator includes a stator having a core and a plurality of stator windings circumferentially spaced about a generator longitudinal axis. A rotor is rotatable about the generator longitudinal axis, and the rotor includes a plurality of magnetic elements coupled to the rotor and cooperating with the stator windings. The magnetic elements are configured to generate a magnetic field and the stator windings are configured to interact with the magnetic field to generate a voltage in the stator windings. A heat pipe assembly thermally engaging one of the stator and the rotor to dissipate heat generated in the stator or rotor.

Salamah, Samir A. (Niskayuna, NY); Gadre, Aniruddha Dattatraya (Rexford, NY); Garg, Jivtesh (Schenectady, NY); Bagepalli, Bharat Sampathkumaran (Niskayuna, NY); Jansen, Patrick Lee (Alplaus, NY); Carl, Jr., Ralph James (Clifton Park, NY)

2008-10-28T23:59:59.000Z

210

AXI LLC | Open Energy Information  

Open Energy Info (EERE)

Page Page Edit with form History Facebook icon Twitter icon » AXI LLC Jump to: navigation, search Name AXI LLC Place Quincy, Massachusetts Zip 02169 Sector Biofuels Product Aims to make commercially feasible strains of algae for fuel production Coordinates 42.2363996°, -71.0200613° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":42.2363996,"lon":-71.0200613,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

211

Nuclear component horizontal seismic restraint  

DOE Patents (OSTI)

A nuclear component horizontal seismic restraint. Small gaps limit horizontal displacement of components during a seismic occurrence and therefore reduce dynamic loadings on the free lower end. The reactor vessel and reactor guard vessel use thicker section roll-forged rings welded between the vessel straight shell sections and the bottom hemispherical head sections. The inside of the reactor guard vessel ring forging contains local vertical dovetail slots and upper ledge pockets to mount and retain field fitted and installed blocks. As an option, the horizontal displacement of the reactor vessel core support cone can be limited by including shop fitted/installed local blocks in opposing alignment with the reactor vessel forged ring. Beams embedded in the wall of the reactor building protrude into apertures in the thermal insulation shell adjacent the reactor guard vessel ring and have motion limit blocks attached thereto to provide to a predetermined clearance between the blocks and reactor guard vessel ring.

Snyder, Glenn J. (Lynchburg, VA)

1988-01-01T23:59:59.000Z

212

EERE: Wind  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

EERE: Buildings The U.S. Department of Energy funds R&D to develop wind energy. Learn about the DOE Wind Program, how to use wind energy and get financial incentives, and access...

213

WIND ENERGY Wind Energ. (2012)  

E-Print Network (OSTI)

WIND ENERGY Wind Energ. (2012) Published online in Wiley Online Library (wileyonlinelibrary since energy production depends non-linearly on wind speed (U ), and wind speed observa- tions for the assessment of future long-term wind supply A. M. R. Bakker1 , B. J. J. M. Van den Hurk1 and J. P. Coelingh2 1

Haak, Hein

214

Horizontal completions challenge for industry  

SciTech Connect

As the technology to drill horizontal wells continues to evolve, the problem of efficiently and cost-effectively completing such wells grows. The economics of applying horizontal technology in high-productivity reservoirs demands both increased production and lower development costs. Such high productivity reservoirs are typical of the Gulf of Mexico, North Sea, South China basin, and other areas. Lowering development costs is achieved by drilling fewer wells and in the offshore environment by reducing the number of platforms and other well structures. Specifically addressed in this article are the problems of achieving high efficiency, long lasting completions while controlling costs in unconsolidated and poorly consolidated sandstone reservoirs.

Zaleski, T.E. Jr.; Spatz, E.

1988-05-02T23:59:59.000Z

215

Theoretical analysis of acceleration measurements in a model of an operating wind turbine.  

Science Conference Proceedings (OSTI)

Wind loading from turbulence and gusts can cause damage in horizontal axis wind turbines. These unsteady loads and the resulting damage initiation and propagation are difficult to predict. Unsteady loads enter at the rotor and are transmitted to the drivetrain. The current generation of wind turbine has drivetrain-mounted vibration and bearing temperature sensors, a nacelle-mounted inertial measurement unit, and a nacelle-mounted anemometer and wind vane. Some advanced wind turbines are also equipped with strain measurements at the root of the rotor. This paper analyzes additional measurements in a rotor blade to investigate the complexity of these unsteady loads. By identifying the spatial distribution, amplitude, and frequency bandwidth of these loads, design improvements could be facilitated to reduce uncertainties in reliability predictions. In addition, dynamic load estimates could be used in the future to control high-bandwidth aerodynamic actuators distributed along the rotor blade to reduce the saturation of slower pitch actuators currently used for wind turbine blades. Local acceleration measurements are made along a rotor blade to infer operational rotor states including deflection and dynamic modal contributions. Previous work has demonstrated that acceleration measurements can be experimentally acquired on an operating wind turbine. Simulations on simplified rotor blades have also been used to demonstrate that mean blade loading can be estimated based on deflection estimates. To successfully apply accelerometers in wind turbine applications for load identification, the spectral and spatial characteristics of each excitation source must be understood so that the total acceleration measurement can be decomposed into contributions from each source. To demonstrate the decomposition of acceleration measurements in conjunction with load estimation methods, a flexible body model has been created with MSC.ADAMS{copyright} The benefit of using a simulation model as opposed to a physical experiment to examine the merits of acceleration-based load identification methods is that models of the structural dynamics and aerodynamics enable one to compare estimates of the deflection and loading with actual values. Realistic wind conditions are applied to the wind turbine and used to estimate the operational displacement and acceleration of the rotor. The per-revolution harmonics dominate the displacement and acceleration response. Turbulent wind produces broadband excitation that includes both the harmonics and modal vibrations, such as the tower modes. Power Spectral Density estimates of the acceleration along the span of the rotor blades indicate that the edge modes may be coupled to the second harmonic.

Adams, Douglas E. (Purdue University, Lafayette, IN); Rumsey, Mark Allen; White, Jonathan Randall

2010-04-01T23:59:59.000Z

216

Wind Regimes Associated with a Mountain Gap at the Northeastern Adriatic Coast  

Science Conference Proceedings (OSTI)

Winds through the Vratnik Pass, a mountain gap in the Dinaric Alps, Croatia, are polarized along the gap axis that extends in the northeast–southwest direction. Although stronger northeasterly wind at the Vratnik Pass is frequently related to the ...

Danijel Beluši?; Mario Hrastinski; Željko Ve?enaj; Branko Grisogono

2013-09-01T23:59:59.000Z

217

Wind Regimes Associated with a Mountain Gap at the Northeastern Adriatic Coast  

Science Conference Proceedings (OSTI)

Winds through the Vratnik Pass, a mountain gap in the Dinaric Alps, Croatia, are polarized along the gap axis that extends in the northeast-southwest direction. Although stronger northeasterly wind at the Vratnik Pass is frequently related to the ...

Danijel Beluši?; Mario Hrastinski; Željko Ve?enaj; Branko Grisogono

218

Systematic approach for PID controller design for pitch-regulated, variable-speed wind turbines  

DOE Green Energy (OSTI)

Variable-speed, horizontal axis wind turbines use blade-pitch control to meet specified objectives for three regions of operation. This paper focuses on controller design for the constant power production regime. A simple, rigid, non-linear turbine model was used to systematically perform trade-off studies between two performance metrics. Minimization of both the deviation of the rotor speed from the desired speed and the motion of the actuator is desired. The robust nature of the proportional-integral-derivative (PID) controller is illustrated, and optimal operating conditions are determined. Because numerous simulation runs may be completed in a short time, the relationship of the two opposing metrics is easily visualized. 2 refs., 9 figs.

Hand, M.M. [National Renewable Energy Lab., Golden, CO (United States); Balas, M.J. [Univ. of Colorado, Boulder, CO (United States). Dept. of Aerospace Engineering Sciences

1997-11-01T23:59:59.000Z

219

Vertax Wind | Open Energy Information  

Open Energy Info (EERE)

Vertax Wind Vertax Wind Jump to: navigation, search Name Vertax Wind Place Surrey, United Kingdom Zip RH2 7LD Sector Wind energy Product Vertax is a British company that develops vertical axis wind turbines Coordinates 48.231575°, -101.134114° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":48.231575,"lon":-101.134114,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

220

Adaptive Control of a Utility-Scale Wind Turbine Operating in Region 3  

Science Conference Proceedings (OSTI)

Many challenges exist for the efficient and safe operation of wind turbines due to the difficulty in creating accurate models of their dynamic characteristics and the turbulent conditions in which they operate. A promising new area of wind turbine research is the application of adaptive control techniques, which are well suited to problems where the plant model is not well known and the plant operating conditions are unpredictable. In this paper, we design an adaptive collective pitch controller for a high-fidelity simulation of a utility scale, variable-speed horizontal axis wind turbine operating in Region 3. The objective of the adaptive pitch controller is to regulate generator speed and reject step disturbances, which model the uniform wind disturbance across the wind turbine rotor. The control objective is accomplished by collectively pitching the turbine blades. To improve controller performance, we use an extension of the Direct Model Reference Adaptive Control (DMRAC) approach to regulate turbine rotational speed and to accommodate step disturbances. The turbine simulation models the Controls Advanced Research Turbine (CART) of the National Renewable Energy Laboratory in Golden, Colorado. The CART is a utility-scale wind turbine that has a well-developed and extensively verified simulator. The adaptive collective pitch controller for Region 3 was compared in simulations with a baseline classical Proportional Integrator (PI) collective pitch controller. In the simulations, the adaptive pitch controller showed improved generator speed regulation in Region 3 when compared with the baseline PI pitch controller. The adaptive controller demonstrated robustness to modeling errors and changes in system parameters.

Frost, S. A.; Balas, M. J.; Wright, A. D.

2009-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "horizontal axis wind" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Effect of Reduced Diffusion on Surface Wind and Wave Fields  

Science Conference Proceedings (OSTI)

Horizontal diffusion is used in meteorological models to reduce noise in the shorter spatial scales and to increase numerical stability. In turn, this affects the surface wind distribution. A series of tests on real situations in the ...

Luigi Cavaleri; Luciana Bertotti; Mariano Hortal; Martin Miller

1997-11-01T23:59:59.000Z

222

Effect of various errors on the Spin Tune and Stable Spin Axis  

DOE Green Energy (OSTI)

Even though RHIC has two full Siberian snakes in each ring, there are various perturbations to the ideal case including orbit errors at the snakes, experiment solenoids, injection bumps, and interlaced horizontal-vertical bumps at the hydrogen jet polarimeter. These errors can cause depolarization by shifting the spin tune and tilting the stable spin direction away from vertical. Tilting of the stable spin axis can enhance horizontal depolarizing resonances. This paper presents preliminary results for some of these error scenarios, as well as their impact on the stable spin directions at STAR and PHENIX.

MacKay,W.W.

2008-10-06T23:59:59.000Z

223

Effect of Various Errors on the Spin Tune and Stable Spin Axis  

DOE Green Energy (OSTI)

Even though RHIC has two full Siberian snakes in each ring, there are various perturbations to the ideal case including orbit errors at the snakes, experiment solenoids, injection bumps, and interlaced horizontal-vertical bumps at the hydrogen jet polarimeter. These errors can cause depolarization by shifting the spin tune and tilting the stable spin direction away from vertical. Tilting of the stable spin axis can enhance horizontal depolarizing resonances. This paper presents preliminary results for some of these error scenarios, as well as their impact on the stable spin directions at STAR and PHENIX.

MacKay,W.W.

2009-01-01T23:59:59.000Z

224

The Characteristics of Wind Velocity that Favor the Fitting of a Weibull Distribution in Wind Speed Analysis  

Science Conference Proceedings (OSTI)

The derivation of the Weibull distribution from the bivariate normal distribution provides theoretical justification for its use in wind speed analysis if four conditions are met. These conditions are that the orthogonal components of horizontal ...

Stanton E. Tuller; Arthur C. Brett

1984-01-01T23:59:59.000Z

225

Use of Mass Conservation and Critical Dividing Streamline concepts for Efficient Objective Analysis of Winds in Complex Terrain  

Science Conference Proceedings (OSTI)

Observed winds and temperature profiles can be used to generate three-dimensional, mass-conserving wind fields that reflect topographical influences. The concept of critical dividing streamlines is used to define quasi-horizontal, flow-confining ...

F. L. Ludwig; J. M. Livingston; R. M. Endlich

1991-11-01T23:59:59.000Z

226

global horizontal | OpenEI  

Open Energy Info (EERE)

87 87 Varnish cache server Browse Upload data GDR 429 Throttled (bot load) Error 429 Throttled (bot load) Throttled (bot load) Guru Meditation: XID: 2142278787 Varnish cache server global horizontal Dataset Summary Description (Abstract): Documentation of the satellite-based high resolution solar resource assessment for Ghana provided by DLR. The high resolution solar data (10kmx10km) provide country maps of the annual and monthly sums of hourly global horizontal and direct normal irradiance (GHI and DNI) for the year 2000, 2001 and 2002. Additionally, for selected sites hourly values of GHI and DNI are provided.The Documentation gives an overview about the used input data and used methodology, shows example maps and describes a comparison with ground data (if provided by the country)

227

Wind Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

FUPWG Meeting FUPWG Meeting NREL is a national laboratory of the U.S. Department of Energy Office of Energy Efficiency and Renewable Energy operated by the Alliance for Sustainable Energy, LLC Robi Robichaud November 18, 2009 Topics Introduction Review of the Current Wind Market Drivers for Wind Development Siting g Issues Wind Resource Assessment Wind Characteristics Wind Power Potential Basic Wind Turbine Theory Basic Wind Turbine Theory Types of Wind Turbines Facts About Wind Siting Facts About Wind Siting Wind Performance 1. United States: MW 1 9 8 2 1 9 8 3 1 9 8 4 1 9 8 5 1 9 8 6 1 9 8 7 1 9 8 8 1 9 8 9 1 9 9 0 1 9 9 1 1 9 9 2 1 9 9 3 1 9 9 4 1 9 9 5 1 9 9 6 1 9 9 7 1 9 9 8 1 9 9 9 2 0 0 0 2 0 0 1 2 0 0 2 2 0 0 3 2 0 0 4 2 0 0 5 2 0 0 6 2 0 0 7 2 0 0 8 Current Status of the Wind Industry Total Global Installed Wind Capacity Total Global Installed Wind Capacity Total Global Installed Wind Capacity

228

Mechanical Design, Analysis, and Testing of a Two-Bladed Wind Turbine Hub  

DOE Green Energy (OSTI)

Researchers at the National Wind Technology Center (NWTC) in Golden, Colorado, began performing the Unsteady Aerodynamics Experiment in 1993 to better understand the unsteady aerodynamics and structural responses of horizontal-axis wind turbines. The experiment consists of an extensively instrumented, downwind, three-bladed, 20-kilowatt wind turbine. In May 1995, I received a request from the NWTC to design a two-bladed hub for the experiment. For my thesis, I present the results of the mechanical design, analysis, and testing of the hub. The hub I designed is unique because it runs in rigid, teetering, or independent blade-flapping modes. In addition, the design is unusual because it uses two servomotors to pitch the blades independently. These features are used to investigate new load reduction, noise reduction, blade pitch optimization, and yaw control techniques for two-bladed turbines. I used a methodology by G. Phal and W. Bietz to design the hub. The hub meets all the performance specifications except that it achieves only 90% of the specified teeter range. In my thesis, I focus on the analysis and testing of the hub body. I performed solid-mechanics calculations, ran a finite-element analysis simulation, and experimentally investigated the structural integrity of the hub body.

Cotrell, J.

2002-06-01T23:59:59.000Z

229

Using digital filtering techniques as an aid in wind turbine data analysis  

DOE Green Energy (OSTI)

Research involving very large sets of digital data is often difficult due to the enormity of the database. In the case of a wind turbine operating under varying environmental conditions, determining which data are representative of the blade aerodynamics and which are due to transient flow ingestion effects or errors in instrumentation, operation, and data collection is of primary concern to researchers. The National Renewable Energy Laboratory in Golden, Colorado collected extensive data on a downwind horizontal axis wind turbine (HAWT) during a turbine test project called the Combined Experiment. A principal objective of this experiment was to provide a means to predict HAWT aerodynamic, mechanical, and electrical operational loads based upon analytical models of aerodynamic performance related to blade design and inflow conditions. In a collaborative effort with the Aerospace Engineering Department at the University of Colorado at Boulder, a team of researchers has evolved and utilized various digital filtering techniques in analyzing the data from the Combined Experiment. A preliminary analysis of the data set was performed to determine how to best approach the data. The reduced data set emphasized selection of inflow conditions such that the aerodynamic data could be compared directly to wind tunnel data obtained for the same airfoil design as used for the HAWT`s blades. It will be shown that this reduced data set has yielded valid, reproducible results that a simple averaging technique or a random selection approach cannot achieve. These findings provide a stable baseline against which operational HAWT data can be compared.

Young, T. [Univ. of Colorado, Boulder, CO (United States). BioServe Space Technologies

1994-11-01T23:59:59.000Z

230

Structural Composites Industries 4-kilowatt wind-system development. Phase I. Design and analysis executive summary  

DOE Green Energy (OSTI)

A 4 kW small wind energy conversion system (SWECS) has been designed for residential applications in which relatively low (10 mph) mean annual wind speeds prevail. The objectives were to develop such a machinee to produce electrical energy at 6 cents per kWh while operating in parallel with a utility grid or auxiliary generator. Extensive trade, optimization and analytical studies were performed in an effort to provide the optimum machine to best meet the objectives. Certain components, systems and manufacturing processes were tested and evaluated and detail design drawings were produced. The resulting design is a 31-foot diameter horizontal axis downwind machine rated 5.7 kW and incorporating composite blades; free-standing composite tower; and torque-actuated blade pitch control. The design meets or exceeds all contract requirements except that for cost of energy. The target 6 cents per kWh will be achieved in a mean wind speed slightly below 12 mph instead of the specified 10 mph.

Malkine, N.; Bottrell, G.; Weingart, O.

1981-05-01T23:59:59.000Z

231

SEACC: the systems engineering and analysis computer code for small wind systems  

DOE Green Energy (OSTI)

The systems engineering and analysis (SEA) computer program (code) evaluates complete horizontal-axis SWECS performance. Rotor power output as a function of wind speed and energy production at various wind regions are predicted by the code. Efficiencies of components such as gearbox, electric generators, rectifiers, electronic inverters, and batteries can be included in the evaluation process to reflect the complete system performance. Parametric studies can be carried out for blade design characteristics such as airfoil series, taper rate, twist degrees and pitch setting; and for geometry such as rotor radius, hub radius, number of blades, coning angle, rotor rpm, etc. Design tradeoffs can also be performed to optimize system configurations for constant rpm, constant tip speed ratio and rpm-specific rotors. SWECS energy supply as compared to the load demand for each hour of the day and during each session of the year can be assessed by the code if the diurnal wind and load distributions are known. Also available during each run of the code is blade aerodynamic loading information.

Tu, P.K.C.; Kertesz, V.

1983-03-01T23:59:59.000Z

232

Structural Composites Industries 4 kilowatt wind system development. Phase I: design and analysis, technical report  

DOE Green Energy (OSTI)

A 4 kW small wind energy conversion system (SWECS) has been designed for residential applications in which relatively low (10 mph) mean annual wind speeds prevail. The objectives were to develop such a machine to produce electrical energy at 6 cents per kWh while operating in parallel with a utility grid or auxiliary generator. The Phase I effort began in November, 1979 and was carried through the Final Design Review in February 1981. During this period extensive trade, optimization and analytical studies were performed in an effort to provide the optimum machine to best meet the objectives. Certain components, systems and manufacturing processes were tested and evaluated and detail design drawings were produced. The resulting design is a 31-foot diameter horizontal axis downwind machine rated 5.7 kW and incorporating the following unique features: Composite Blades; Free-Standing Composite Tower; Torque-Actuated Blade Pitch Control. The design meets or exceeds all contract requirements except that for cost of energy. The target 6 cents per kWh will be achieved in a mean wind speed slightly below 12 mph instead of the specified 10 mph.

Malkine, N.; Bottrell, G.; Weingart, O.

1981-05-01T23:59:59.000Z

233

The Canopy Horizontal Array Turbulence Study  

Science Conference Proceedings (OSTI)

The Canopy Horizontal Array Turbulence Study (CHATS) took place in spring 2007 and is the third in the series of Horizontal Array Turbulence Study (HATS) experiments. The HATS experiments have been instrumental in testing and developing subfilterscale (...

Edward G. Patton; Thomas W. Horst; Peter P. Sullivan; Donald H. Lenschow; Steven P. Oncley; William O. J. Brown; Sean P. Burns; Alex B. Guenther; Andreas Held; Thomas Karl; Shane D. Mayor; Luciana V. Rizzo; Scott M. Spuler; Jielun Sun; Andrew A. Turnipseed; Eugene J. Allwine; Steven L. Edburg; Brian K. Lamb; Roni Avissar; Ronald J. Calhoun; Jan Kleissl; William J. Massman; Kyaw Tha Paw U; Jeffrey C. Weil

2011-05-01T23:59:59.000Z

234

Growing Nanowires Horizontally Yields New Benefit: 'Nano ...  

Science Conference Proceedings (OSTI)

Growing Nanowires Horizontally Yields New Benefit: 'Nano-LEDs'. ... Optical microscope image of “nano LEDs” emitting light. ...

2012-10-17T23:59:59.000Z

235

Definition: Global horizontal irradiance | Open Energy Information  

Open Energy Info (EERE)

Normal Irradiance (DNI) and Diffuse Horizontal Irradiance (DIF).1 Related Terms DNI, Solar radiation, Concentrating solar power, Photovoltaics References http:...

236

Evaluation of Three-Beam and Four-Beam Profiler Wind Measurement Techniques Using a Five-Beam Wind Profiler and Collocated Meteorological Tower  

Science Conference Proceedings (OSTI)

In this paper a five-beam wind profiler and a collocated meteorological tower are used to estimate the accuracy of four-beam and three-beam wind profiler techniques in measuring horizontal components of the wind. In the traditional three-beam ...

Ahoro Adachi; Takahisa Kobayashi; Kenneth S. Gage; David A. Carter; Leslie M. Hartten; Wallace L. Clark; Masato Fukuda

2005-08-01T23:59:59.000Z

237

Climatology of High Wind Events in the Owens Valley, California  

Science Conference Proceedings (OSTI)

The climatology of high wind events in the Owens Valley, California, a deep valley located just east of the southern Sierra Nevada, is described using data from six automated weather stations distributed along the valley axis in combination with ...

Shiyuan Zhong; Ju Li; C. David Whiteman; Xindi Bian; Wenqing Yao

2008-09-01T23:59:59.000Z

238

Energy age wind ltd Co KG | Open Energy Information  

Open Energy Info (EERE)

age wind ltd Co KG age wind ltd Co KG Jump to: navigation, search Name energy-age-wind ltd & Co. KG Place Telgte, Germany Zip 48291 Sector Wind energy Product Energy-age-wind aims to develop small scale vertical-axis wind turbines. References energy-age-wind ltd & Co. KG[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. energy-age-wind ltd & Co. KG is a company located in Telgte, Germany . References ↑ "energy-age-wind ltd & Co. KG" Retrieved from "http://en.openei.org/w/index.php?title=Energy_age_wind_ltd_Co_KG&oldid=344826" Categories: Clean Energy Organizations Companies Organizations Stubs What links here Related changes Special pages Printable version

239

Strain Rate Dependence of Mechanical Properties and Failure ...  

Science Conference Proceedings (OSTI)

Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades · Sustainability, Recycling, and Waste Treatment in the Aluminum Industry .

240

Layered Materials as Colored Reinforcement for Polymeric ...  

Science Conference Proceedings (OSTI)

Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades · Sustainability, Recycling, and Waste Treatment in the Aluminum Industry .

Note: This page contains sample records for the topic "horizontal axis wind" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Synoptic-Scale Environments Conducive to Orographic Impacts on Cold-Season Surface Wind Regimes at Montreal, Quebec  

Science Conference Proceedings (OSTI)

Orographic wind channeling, defined as dynamically and thermally induced processes that force wind to blow along the axis of a valley, is a common occurrence along the St. Lawrence River Valley (SLRV) in Quebec, Canada, and produces substantial ...

Alissa Razy; Shawn M. Milrad; Eyad H. Atallah; John R. Gyakum

2012-03-01T23:59:59.000Z

242

EIA: Wind  

U.S. Energy Information Administration (EIA)

Technical information and data on the wind energy industry from the U.S. Energy Information Administration (EIA).

243

Helical axis stellarator with noninterlocking planar coils  

DOE Patents (OSTI)

A helical axis stellarator using only noninterlocking planar, non-circular coils, generates magnetic fields having a magnetic well and large rotational transform with resultant large equilibrium beta.

Reiman, Allan (Princeton, NJ); Boozer, Allen H. (Rocky Hill, NJ)

1987-01-01T23:59:59.000Z

244

Wind Blog  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

wind-blog Office of Energy Efficiency & Renewable wind-blog Office of Energy Efficiency & Renewable Energy Forrestal Building 1000 Independence Avenue, SW Washington, DC 20585 en Two Facilities, One Goal: Advancing America's Wind Industry http://energy.gov/eere/articles/two-facilities-one-goal-advancing-america-s-wind-industry wind-industry" class="title-link">Two Facilities, One Goal: Advancing America's Wind Industry

245

Coupled Dynamic Analysis of Multiple Unit Floating Offshore Wind Turbine  

E-Print Network (OSTI)

In the present study, a numerical simulation tool has been developed for the rotor-floater-tether coupled dynamic analysis of Multiple Unit Floating Offshore Wind Turbine (MUFOWT) in the time domain including aero-blade-tower dynamics and control, mooring dynamics and platform motion. In particular, the numerical tool developed in this study is based on the single turbine analysis tool FAST, which was developed by National Renewable Energy Laboratory (NREL). For linear or nonlinear hydrodynamics of floating platform and generalized-coordinate-based FEM mooring line dynamics, CHARM3D program, hull-riser-mooring coupled dynamics program developed by Prof. M.H. Kim’s research group during the past two decades, is incorporated. So, the entire dynamic behavior of floating offshore wind turbine can be obtained by coupled FAST-CHARM3D in the time domain. During the coupling procedure, FAST calculates all the dynamics and control of tower and wind turbine including the platform itself, and CHARM3D feeds all the relevant forces on the platform into FAST. Then FAST computes the whole dynamics of wind turbine using the forces from CHARM3D and return the updated displacements and velocities of the platform to CHARM3D. To analyze the dynamics of MUFOWT, the coupled FAST-CHARM3D is expanded more and re-designed. The global matrix that includes one floating platform and a number of turbines is built at each time step of the simulation, and solved to obtain the entire degrees of freedom of the system. The developed MUFOWT analysis tool is able to compute any type of floating platform with various kinds of horizontal axis wind turbines (HAWT). Individual control of each turbine is also available and the different structural properties of tower and blades can be applied. The coupled dynamic analysis for the three-turbine MUFOWT and five-turbine MUFOWT are carried out and the performances of each turbine and floating platform in normal operational condition are assessed. To investigate the coupling effect between platform and each turbine, one turbine failure event is simulated and checked. The analysis shows that some of the mal-function of one turbine in MUFOWT may induce significant changes in the performance of other turbines or floating platform. The present approach can directly be applied to the development of the remote structural health monitoring system of MUFOWT in detecting partial turbine failure by measuring tower or platform responses in the future.

Bae, Yoon Hyeok

2013-05-01T23:59:59.000Z

246

Conductor assembly formed about a curved axis  

DOE Patents (OSTI)

A conductor assembly of the type which, when conducting current, generates a magnetic field or in which, in the presence of a changing magnetic field, a voltage is induced. In the assembly a first layer, tubular in shape, is formed about an axis. The axis includes a curved portion along which a conductor may be positioned to define a first conductor path. The first layer also includes a curved portion having a shape that includes a curve extending along the curved portion of the axis. A first conductor is arranged about the curved portion of the first layer in a first helical configuration including a curved segment, helical in shape and formed about the curved portion of the axis. The configuration is capable of sustaining a magnetic field having multipole components oriented in directions transverse to the axis.

Meinke, Rainer (Melbourne, FL)

2011-02-15T23:59:59.000Z

247

TMA Global Wind Energy Systems | Open Energy Information  

Open Energy Info (EERE)

TMA Global Wind Energy Systems TMA Global Wind Energy Systems Jump to: navigation, search Name TMA Global Wind Energy Systems Place Cheyenne, Wyoming Zip 82001 Sector Wind energy Product Involved in the development, manufacture, and marketing of vertical axis wind energy turbines and hybrid energy systems. References TMA Global Wind Energy Systems[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. TMA Global Wind Energy Systems is a company located in Cheyenne, Wyoming . References ↑ "TMA Global Wind Energy Systems" Retrieved from "http://en.openei.org/w/index.php?title=TMA_Global_Wind_Energy_Systems&oldid=352301" Categories: Clean Energy Organizations Companies Organizations

248

Solar: monthly and annual average direct normal (DNI), global horizontal  

Open Energy Info (EERE)

East Asia from NREL East Asia from NREL Dataset Summary Description (Abstract): Monthly Average Solar Resource for horizontal and tilted flat-plates, and 2-axis tracking concentrating collectors. (Purpose): Provide information on the solar resource potential for the data domain. The insolation values represent the average solar energy available to solar collectors. (Supplemental Information): These data provide monthly average and annual average daily total solar resource averaged over surface cells of approximately 40 km by 40 km in size. The solar resource value is represented as watt-hours per square meter per day for each month. The data were developed from NREL's Climatological Solar Radiation (CSR) Model. This model uses information on cloud cover, atmospheric water

249

Solar: monthly and annual average direct normal (DNI), global horizontal  

Open Energy Info (EERE)

Africa from NREL Africa from NREL Dataset Summary Description (Abstract): Monthly Average Solar Resource for horizontal and tilted flat-plates, and 2-axis tracking concentrating collectors. (Purpose): Provide information on the solar resource potential for the data domain. The insolation values represent the average solar energy available to solar collectors. (Supplemental Information): These data provide monthly average and annual average daily total solar resource averaged over surface cells of approximately 40 km by 40 km in size. The solar resource value is represented as watt-hours per square meter per day for each month. The data were developed from NREL's Climatological Solar Radiation (CSR) Model. This model uses information on cloud cover, atmospheric water

250

Energy Basics: Wind Turbines  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Energy Basics Renewable Energy Printable Version Share this resource Biomass Geothermal Hydrogen Hydropower Ocean Solar Wind Wind Turbines Wind Resources Wind Turbines...

251

Standards for Municipal Small Wind Regulations and Small Wind...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Standards for Municipal Small Wind Regulations and Small Wind Model Wind Ordinance Standards for Municipal Small Wind Regulations and Small Wind Model Wind Ordinance Eligibility...

252

NREL: Wind Research - Large Wind Turbine Research  

NLE Websites -- All DOE Office Websites (Extended Search)

Wind Research Search More Search Options Site Map Printable Version Large Wind Turbine Research NREL's utility scale wind system research addresses performance and...

253

Solar: monthly and annual average direct normal (DNI), global horizontal  

Open Energy Info (EERE)

South America from NREL South America from NREL Dataset Summary Description (Abstract): Monthly Average Solar Resource for horizontal and tilted flat-plates, and 2-axis tracking concentrating collectors. (Purpose): Provide information on the solar resource potential for the data domain. The insolation values represent the average solar energy available to solar collectors. (Supplemental Information): These data provide monthly average and annual average daily total solar resource averaged over surface cells of approximately 40 km by 40 km in size. The solar resource value is represented as watt-hours per square meter per day for each month. The data were developed from NREL's Climatological Solar Radiation (CSR) Model. This model uses information on cloud cover, atmospheric water vapor and trace gases, and the amount of aerosols in the atmosphere to calculate the monthly average daily total insolation (sun and sky) falling on a horizontal surface. Existing ground measurement stations are used to validate the data where possible. The modeled values are accurate to approximately 10% of a true measured value within the grid cell due to the uncertainties associated with meteorological input to the model. The local cloud cover can vary significantly even within a single grid cell as a result of terrain effects and other microclimate influences. Furthermore, the uncertainty of the modeled estimates increase with distance from reliable measurement sources and with the complexity of the terrain.

254

Solar: monthly and annual average direct normal (DNI), global horizontal  

Open Energy Info (EERE)

Central America and the Carribean from NREL Central America and the Carribean from NREL Dataset Summary Description (Abstract): Monthly Average Solar Resource for horizontal and tilted flat-plates, and 2-axis tracking concentrating collectors. (Purpose): Provide information on the solar resource potential for the data domain. The insolation values represent the average solar energy available to solar collectors. (Supplemental Information): These data provide monthly average and annual average daily total solar resource averaged over surface cells of approximately 40 km by 40 km in size. The solar resource value is represented as watt-hours per square meter per day for each month. The data were developed from NREL's Climatological Solar Radiation (CSR) Model. This model uses information on cloud cover, atmospheric water vapor and trace gases, and the amount of aerosols in the atmosphere to calculate the monthly average daily total insolation (sun and sky) falling on a horizontal surface. Existing ground measurement stations are used to validate the data where possible. The modeled values are accurate to approximately 10% of a true measured value within the grid cell due to the uncertainties associated with meteorological input to the model. The local cloud cover can vary significantly even within a single grid cell as a result of terrain effects and other microclimate influences. Furthermore, the uncertainty of the modeled estimates increase with distance from reliable measurement sources and with the complexity of the terrain.

255

Wind Powering America: Wind Events  

Wind Powering America (EERE)

calendar.asp Lists upcoming wind calendar.asp Lists upcoming wind power-related events. en-us julie.jones@nrel.gov (Julie Jones) http://www.windpoweringamerica.gov/images/wpa_logo_sm.jpg Wind Powering America: Wind Events http://www.windpoweringamerica.gov/calendar.asp Pennsylvania Wind for Schools Educator Workshop https://www.regonline.com/builder/site/Default.aspx?EventID=1352684 http://www.windpoweringamerica.gov/filter_detail.asp?itemid=4068 Wed, 4 Dec 2013 00:00:00 MST 2014 Joint Action Workshop http://www.windpoweringamerica.gov/filter_detail.asp?itemid=3996 http://www.windpoweringamerica.gov/filter_detail.asp?itemid=3996 Mon, 21 Oct 2013 00:00:00 MST AWEA Wind Project Operations and Maintenance and Safety Seminar http://www.windpoweringamerica.gov/filter_detail.asp?itemid=4009 http://www.windpoweringamerica.gov/filter_detail.asp?itemid=4009 Mon, 21

256

Gravel packing feasible in horizontal well completions  

SciTech Connect

Successful completion of horizontal wells in unconsolidated formations depends on proper equipment selection and installation method balanced with reservoir objectives, formation parameters, and costs. The guidelines for designing these completions are based on generalized field experience, including horizontal cases where applicable.

Zaleski, T.E. Jr.; Ashton, J.P. (Baker Sand Control, Houston, TX (US))

1990-06-11T23:59:59.000Z

257

Wooden wind turbine blade manufacturing process  

DOE Patents (OSTI)

A wooden wind turbine blade is formed by laminating wood veneer in a compression mold having the exact curvature needed for one side of the blade, following which the other side of the blade is ground flat along its length but twisted with respect to the blade axis.

Coleman, Clint (Warren, VT)

1986-01-01T23:59:59.000Z

258

global horizontal irradiance | OpenEI  

Open Energy Info (EERE)

horizontal irradiance horizontal irradiance Dataset Summary Description (Abstract): Global Horizontal IrradianceNASA Surface meteorology and Solar Energy (SSE) Release 6.0 Data Set (Jan 2008)22-year Monthly & Annual Average (July 1983 - June 2005) Parameter: Insolation Incident On A Horizontal Surface (kWh/m^2/day) Internet: http://eosweb.larc.nasa.gov/sse/ Note 1: SSE Methodology & Accuracy sections online Note 2: Lat/Lon values indicate the lower left corner of a 1x1 degree region. Negative values are south and west; Source U.S. National Aeronautics and Space Administration (NASA), Surface meteorology and Solar Energy (SSE) Date Released March 31st, 2009 (5 years ago) Date Updated April 01st, 2009 (5 years ago) Keywords GHI GIS global horizontal irradiance NASA solar

259

Dual Axis Radiographic Hydrodynamic Test Facility  

NLE Websites -- All DOE Office Websites (Extended Search)

DARHT Facility: A critical component of stockpile stewardship DARHT Facility: A critical component of stockpile stewardship A new research frontier awaits! Our door is open and we thrive on mutually beneficial partnerships, collaborations that drive innovations and new technologies. April 12, 2012 Dominic Tafoya and Dave Honaberger prepare a refurbished DARHT (Dual Axis Radiographic Hydrotest Facility) 2nd axis accelerator cell for magnetic axis alignment measurements. Contact Group Leader Terry Priestley (505) 665-1330 Email Deputy Group Leader Tim Ferris (505) 665-2179 Email Hydrotests are critical in assessing nuclear weapons in nation's stockpile Dual Axis Radiographic Hydrodynamic Test facility 4:17 How DARHT Works The weapons programs at Los Alamos have one principal mission: ensure the safety, security, and effectiveness of nuclear weapons in our nation's

260

Feasibility and optical performance of one axis three positions sun-tracking polar-axis aligned CPCs for photovoltaic applications  

SciTech Connect

A new design concept, called one axis three positions sun-tracking polar-axis aligned CPCs (3P-CPCs, in short), was proposed and theoretically studied in this work for photovoltaic applications. The proposed trough-like CPC is oriented in the polar-axis direction, and the aperture is daily adjusted eastward, southward, and westward in the morning, noon and afternoon, respectively, by rotating the CPC trough, to ensure efficient collection of beam radiation nearly all day. To investigate the optical performance of such CPCs, an analytical mathematical procedure is developed to estimate daily and annual solar gain captured by such CPCs based on extraterrestrial radiation and monthly horizontal radiation. Results show that the acceptance half-angle of 3P-CPCs is a unique parameter to determine their optical performance according to extraterrestrial radiation, and the annual solar gain stays constant if the acceptance half-angle, {theta}{sub a}, is less than one third of {omega}{sub 0,min}, the sunset hour angle in the winter solstice, otherwise decreases with the increase of {theta}{sub a}. For 3P-CPCs used in China, the annual solar gain, depending on the climatic conditions in site, decreased with the acceptance half-angle, but such decrease was slow for the case of {theta}{sub a}{<=}{omega}{sub 0,min}/3, indicating that the acceptance half-angle should be less than one third of {omega}{sub 0,min} for maximizing annual energy collection. Compared to fixed east-west aligned CPCs (EW-CPCs) with a yearly optimal acceptance half-angle, the fixed south-facing polar-axis aligned CPCs (1P-CPCs) with the same acceptance half-angle as the EW-CPCs annually collected about 65-74% of that EW-CPCs did, whereas 3P-CPCs annually collected 1.26-1.45 times of that EW-CPCs collected, indicating that 3P-CPCs were more efficient for concentrating solar radiation onto their coupling solar cells. (author)

Tang, Runsheng; Yu, Yamei [Education Ministry Key Laboratory of Advanced Technology and Preparation for Renewable Energy Materials, Yunnan Normal University, Kunming 650092 (China)

2010-09-15T23:59:59.000Z

Note: This page contains sample records for the topic "horizontal axis wind" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Extreme Winds and Wind Effects on Structures  

Science Conference Proceedings (OSTI)

Extreme Winds and Wind Effects on Structures. Description/Summary: The Building and Fire Research Laboratory has an ...

2010-10-04T23:59:59.000Z

262

Development and Test Plans for a small Vertical Axis Turbine Designed and  

NLE Websites -- All DOE Office Websites (Extended Search)

Development and Test Plans for a small Vertical Axis Turbine Designed and Development and Test Plans for a small Vertical Axis Turbine Designed and Built by the Russian State Rocket Center under Berkeley Lab auspices Speaker(s): Anthony Radspieler Jr. Glen Dahlbacka Joseph Rasson Date: March 4, 2010 - 12:00pm Location: 90-3122 Berkeley Lab Engineering Division teamed with Empire Magnetics, Rohnert Park and the Makeyev State Rocket Center under a DOE NNSA non-proliferation project to develop and test a series of small wind turbines of vertical axis design. Over the years, about 100 Russian scientists and engineers worked on the project and the hydrodynamic, aerodynamic and mechanical test facilities of the SRC were used. The objective was to create a highly manufacturable Darieus unit with a modest Tip Speed Ratio (quiet and low

263

Wind Energy Leasing Handbook  

E-Print Network (OSTI)

Wind Energy Leasing Handbook Wind Energy Leasing Handbook E-1033 Oklahoma Cooperative Extension?..................................................................................................................... 31 What do wind developers consider in locating wind energy projects?............................................................................................ 37 How do companies and individuals invest in wind energy projects?....................................................................

Balasundaram, Balabhaskar "Baski"

264

Wind Powering America: New England Wind Forum  

Wind Powering America (EERE)

About the New England Wind Forum About the New England Wind Forum New England Wind Energy Education Project Historic Wind Development in New England State Activities Projects in New England Building Wind Energy in New England Wind Resource Wind Power Technology Economics Markets Siting Policy Technical Challenges Issues Small Wind Large Wind Newsletter Perspectives Events Quick Links to States CT MA ME NH RI VT Bookmark and Share The New England Wind Forum was conceived in 2005 as a platform to provide a single, comprehensive and objective source of up-to-date, Web-based information on a broad array of wind-energy-related issues pertaining to New England. The New England Wind Forum provides information to wind energy stakeholders through Web site features, periodic newsletters, and outreach activities. The New England Wind Forum covers the most frequently discussed wind energy topics.

265

Two-Dimensional Vector Wind Fields from Volume Imaging Lidar Data  

Science Conference Proceedings (OSTI)

Spatially resolved wind fields are derived by cross correlation of aerosol backscatter data from horizontal and vertical scans of the University of Wisconsin volume imaging lidar during the 1997/98 Lake-Induced Convection Experiment. Data from ...

Shane D. Mayor; Edwin W. Eloranta

2001-08-01T23:59:59.000Z

266

Observed Boundary Layer Wind Structure and Balance in the Hurricane Core. Part I: Hurricane Georges  

Science Conference Proceedings (OSTI)

The GPS dropsonde allows observations at unprecedentedly high horizontal and vertical resolution, and of very high accuracy, within the tropical cyclone boundary layer. These data are used to document the boundary layer wind field of the core of ...

Jeffrey D. Kepert

2006-09-01T23:59:59.000Z

267

Mechanisms of Along-Valley Winds and Heat Exchange over Mountainous Terrain  

Science Conference Proceedings (OSTI)

The physical mechanisms leading to the formation of diurnal along-valley winds are investigated over idealized three-dimensional topography. The topography used in this study consists of a valley with a horizontal floor enclosed by two isolated ...

Juerg Schmidli; Richard Rotunno

2010-09-01T23:59:59.000Z

268

Southern Ocean Response to Strengthening Winds in an Eddy-Permitting Global Climate Model  

Science Conference Proceedings (OSTI)

A global climate model with horizontal resolutions in the ocean ranging from relatively coarse to eddy permitting is used to investigate the resolution dependence of the Southern Ocean response to poleward intensifying winds through the past and ...

Paul Spence; John C. Fyfe; Alvaro Montenegro; Andrew J. Weaver

2010-10-01T23:59:59.000Z

269

Satellite-Derived Surface Current Divergence in Relation to Tropical Atlantic SST and Wind  

Science Conference Proceedings (OSTI)

The relationships between tropical Atlantic Ocean surface currents and horizontal (mass) divergence, sea surface temperature (SST), and winds on monthly-to-annual time scales are described for the time period from 1993 through 2003. Surface ...

Robert W. Helber; Robert H. Weisberg; Fabrice Bonjean; Eric S. Johnson; Gary S. E. Lagerloef

2007-05-01T23:59:59.000Z

270

Development of a Nationwide, Low-Level Wind Shear Mosaic in France  

Science Conference Proceedings (OSTI)

An algorithm for the detection of horizontal wind shear at low levels was developed. The algorithm makes use of data collected by all radars from the Application Radar à la Météorologie Infra-Synoptique (ARAMIS) operational network, in order to ...

Clotilde Augros; Pierre Tabary; Adrien Anquez; Jean-Marc Moisselin; Pascal Brovelli; Olivier Bousquet

2013-10-01T23:59:59.000Z

271

Enhancement of Crosswind Pollutant Dispersion by Steadily Veering Winds in Sea Breezes  

Science Conference Proceedings (OSTI)

An estimate is given of the relative importance of wind veering and turbulent diffusion in the mean horizontal spread of pollutant plumes in the atmosphere. Documented veering rates in sea breezes are used to illustrate the effect, and it is ...

D. G. Steyn; M. Segal

1990-05-01T23:59:59.000Z

272

Vertical Reynolds Stress Divergence in the Upper Ocean Associated with Linear Wind-Driven, Near-Inertial Waves of Finite Wavelength  

Science Conference Proceedings (OSTI)

Study of a schematic linear, wind-driven, inertio–gravity wave model in the upper ocean finds resonant, near-inertial waves of finite horizontal wavelength to have both horizontal and vertical motions. The mean product of these horizontal motions ...

Warren B. White

1986-07-01T23:59:59.000Z

273

Accessibility in 5-Axis Milling Environment  

E-Print Network (OSTI)

Using algorithms from computer graphics, namely hidden line and surface removal, techniques have been constructed to derive the 3-axis visible or millable set of a computer model from a given orientation or simulate and verify machining toolpaths. In this paper, an approach that reduces the accessibility problem of 5-axis milling using a flat end tool into a 3-axis accessibility problem is discussed. Using this approach, global detection of possible gouging into other parts, while a 5-axis flat end mill is in use, is made feasible and collisions can be avoided. Key Words: NURBs, accessibility, 5-axis machining. 1 Introduction Several methods are in use, when freeform computer models are realized using milling machines. Possibly the most common approach utilizes a ball end tool with three degrees of freedom, namely translation in x, y, and z [1, 2, 4, 5, 6, 7]. The ball end center of the tool follows an offset [8] to the model by the tool radius while the ball end surface is tangent to...

Gershon Elber

1997-01-01T23:59:59.000Z

274

Wind News  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

news Office of Energy Efficiency & Renewable news Office of Energy Efficiency & Renewable Energy Forrestal Building 1000 Independence Avenue, SW Washington, DC 20585 en New Report Shows Trend Toward Larger Offshore Wind Systems, with 11 Advanced Stage Projects Proposed in U.S. Waters http://energy.gov/eere/articles/new-report-shows-trend-toward-larger-offshore-wind-systems-11-advanced-stage-projects wind-systems-11-advanced-stage-projects" class="title-link">New Report Shows Trend Toward Larger Offshore Wind Systems, with 11 Advanced Stage Projects Proposed in U.S. Waters

275

Wind Power  

NLE Websites -- All DOE Office Websites (Extended Search)

Power As the accompanying map of New Mexico shows, the best wind power generation potential near WIPP is along the Delaware Mountain ridge line of the southern Guadalupe Mountains,...

276

Dual Axis Radiographic Hydrodynamic Test Facility, IG-0599 |...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Administration Other Agencies You are here Home Dual Axis Radiographic Hydrodynamic Test Facility, IG-0599 Dual Axis Radiographic Hydrodynamic Test Facility, IG-0599 The Dual...

277

Modular Off-Axis Fiber Optic Solar Concentrator  

interior lighting: Sunlight Direct, ... a Modular Off-Axis Fiber Optic Solar Concentrator, uses novel embodiments of an off-axis aspheric focusing system to achieve ...

278

Proper centralizers can improve horizontal well cementing  

SciTech Connect

The selection and spacing of appropriate centralizers can improve the cementation of high-angle and horizontal wells. Mud removal is one of the most important factors in obtaining a good cement job. Effective centralization assists in mud removal and helps ensure an even cement coat around the casing. Centralizers for horizontal wells have to fulfill two requirements: They should have a high restoring capability and a low moving force, and they should allow pipe rotation and reciprocation. Conventional bow-type centralizers have been used successfully in some horizontal wells. But as the horizontal section length increases, special centralizers, such as low-moving-force, bow-type centralizers and rigid centralizers, may be necessary. The paper describes the following: cementing liners, centralization, torque and drag, centralizer placement, the bow-type centralizer, the rigid centralizer, and the downhole activated centralizer.

Kinzel, H. (Weatherford Oil Tool, Langenhagen (Germany))

1993-09-20T23:59:59.000Z

279

Horizontal Roll Vortices and Crown Fires  

Science Conference Proceedings (OSTI)

Observational evidence from nine crown fires suggests that horizontal roll vortices are a major mechanism in crown-fire spread. Post-burn aerial photography indicates that unburned tree-crown streets are common with crown fire. Investigation of ...

Donald A. Haines

1982-06-01T23:59:59.000Z

280

Axis Technologies Group Inc | Open Energy Information  

Open Energy Info (EERE)

Axis Technologies Group Inc Axis Technologies Group Inc Jump to: navigation, search Name Axis Technologies Group, Inc Place Lincoln, Nebraska Zip 68522 Product Designs, manufactures, and markets energy-saving and daylight harvesting electronic dimming ballasts for the commercial lighting industry. Coordinates 47.829403°, -118.419202° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":47.829403,"lon":-118.419202,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

Note: This page contains sample records for the topic "horizontal axis wind" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Enclosed, off-axis solar concentrator  

SciTech Connect

A solar concentrator including a housing having receiving wall, a reflecting wall and at least two end walls, the receiving, reflecting and end walls defining a three-dimensional volume having an inlet, wherein a vertical axis of the housing is generally perpendicular to the inlet, a receiver mounted on the receiving wall of the housing, the receiver including at least one photovoltaic cell, wherein a vertical axis of the receiver is disposed at a non-zero angle relative to the vertical axis of the housing, at least one clip disposed on the reflecting wall an optical element received within the three-dimensional volume, the optical element including at least one tab, the tab being engaged by the clip to align the optical element with the receiver, and a window received over the inlet to enclose the housing.

Benitez, Pablo; Grip, Robert E; Minano, Juan C; Narayanan, Authi A; Plesniak, Adam; Schwartz, Joel A

2013-11-26T23:59:59.000Z

282

Site insolation and wind power characteristics: technical report Midwest region  

SciTech Connect

This phase of the Site Insolation and Wind Power Characteristics Study was performed to provide statistical information on the expected future availability of solar and wind power at various sites in the Midwest Region of the US Historic data (SOLMET), at 22 National Weather Service stations with hourly solar insolation and collateral meteorological information, were interrogated to provide an estimate of future trends. Solar data are global radiation incident on a horizontal surface, and wind data represent wind power normal to the air flow. Selected insolation and wind power conditions were investigated for their occurrence and persistence, for defined periods of time, on a monthly basis. Global horizontal insolation is related to inclined surfaces at each site. Ratios are provided, monthly, for multiplying global insolation to obtain insolation estimates on south-facing surfaces inclined at different angles with respect to the horizontal. Also, joint probability distribution tables are constructed showing the number of occurrences, out of a finite sample size, of daily average solar and wind power within selected intervals, by month. Information of this nature is intended as an aid to preliminary planning activities for the design and operation of solar and wind energy utilization and conversion systems.

1980-08-01T23:59:59.000Z

283

Economic viability of multiple-lateral horizontal wells.  

E-Print Network (OSTI)

??Horizontal wells are gaining popularity throughout the petroleum industry as a means to increase well productivity and enhance incremental economics. Horizontal wells provide greater reservoir… (more)

Smith, Christopher Jason

2012-01-01T23:59:59.000Z

284

Site insolation and wind power characteristics, technical report northeast region. Vol. 2  

SciTech Connect

This phase of the Site Insolation and Wind Power Characteristics Study was performed to provide statistical information on the expected future availability of solar and wind power at various sites in the Northeast Region of the US Historic data (SOLMET), at 8 National Weather Service stations with hourly solar insolation and collateral meteorological information, were interrogated to provide an estimate of future trends. Solar data are global radiation incident on a horizontal surface, and wind data represent wind power normal to the air flow. Selected insolation and wind power conditions were investigated for their occurrence and persistence, for defined periods of time, on a monthly basis. Global horizontal insolation are related to inclined surfaces at each site. Ratios are provided, monthly, for multiplying global insolation to obtain insolation estimates on south-facing surfaces inclined at different angles with respect to the horizontal.

None

1980-08-01T23:59:59.000Z

285

Visibility graph analysis of solar wind velocity  

E-Print Network (OSTI)

We analyze in situ measurements of solar wind velocity obtained by Advanced Composition Explorer (ACE) spacecraft and Helios spacecraft during the years 1998-2012 and 1975-1983 respectively. The data belong to mainly solar cycle 23 (1996-2008) and solar cycle 21 (1976-1986) respectively. We use Directed Horizontal Visibility graph (DHVg) algorithm and estimate a graph functional, namely, the degree distance (D) as the Kullback-Leibler divergence (KLD) argument to understand time irreversibility of solar wind time series. We estimate this degree distance irreversibility parameter for these time series at different phases of solar activity cycle. Irreversibility parameter is first established for known dynamical data and then applied for solar wind velocity time series. It is observed that irreversibility in solar wind velocity fluctuations show similar behaviour at 0.3 AU (Helios data) and 1 AU (ACE data). Moreover it changes over the different phases of solar activity cycle.

Suyal, Vinita; Singh, Harinder P

2013-01-01T23:59:59.000Z

286

New England Wind Forum: Wind Power Technology  

Wind Powering America (EERE)

Wind Power Technology Wind Power Technology Modern wind turbines have become sophisticated power plants while the concept of converting wind energy to electrical energy remains quite simple. Follow these links to learn more about the science behind wind turbine technology. Wind Power Animation An image of a scene from the wind power animation. The animation shows how moving air rotates a wind turbine's blades and describes how the internal components work to produce electricity. It shows small and large wind turbines and the differences between how they are used, as stand alone or connected to the utility grid. How Wind Turbines Work Learn how wind turbines make electricity; what are the types, sizes, and applications of wind turbines; and see an illustration of the components inside a wind turbine.

287

NREL: Wind Research - Wind Resource Assessment  

NLE Websites -- All DOE Office Websites (Extended Search)

Wind Resource Assessment Wind Resource Assessment A map of the United States is color-coded to indicate the high winds at 80 meters. This map shows the wind resource at 80 meters for both land-based and offshore wind resources in the United States. Correct estimation of the energy available in the wind can make or break the economics of wind plant development. Wind mapping and validation techniques developed at the National Wind Technology Center (NWTC) along with collaborations with U.S. companies have produced high-resolution maps of the United States that provide wind plant developers with accurate estimates of the wind resource potential. State Wind Maps International Wind Resource Maps Dynamic Maps, GIS Data, and Analysis Tools Due to the existence of special use airspace (SUA) (i.e., military airspace

288

Wind loading on solar concentrators: some general considerations  

DOE Green Energy (OSTI)

A survey has been completed to examine the problems and complications arising from wind loading on solar concentrators. Wind loading is site specific and has an important bearing on the design, cost, performance, operation and maintenance, safety, survival, and replacement of solar collecting systems. Emphasis herein is on paraboloidal, two-axis tracking systems. Thermal receiver problems also are discussed. Wind characteristics are discussed from a general point of view; current methods for determining design wind speed are reviewed. Aerodynamic coefficients are defined and illustrative examples are presented. Wind tunnel testing is discussed, and environmental wind tunnels are reviewed; recent results on heliostat arrays are reviewed as well. Aeroelasticity in relation to structural design is discussed briefly. Wind loads, i.e., forces and moments, are proportional to the square of the mean wind velocity. Forces are proportional to the square of concentrator diameter, and moments are proportional to the cube of diameter. Thus, wind loads have an important bearing on size selection from both cost and performance standpoints. It is concluded that sufficient information exists so that reasonably accurate predictions of wind loading are possible for a given paraboloidal concentrator configuration, provided that reliable and relevant wind conditions are specified. Such predictions will be useful to the design engineer and to the systems engineer as well. Information is lacking, however, on wind effects in field arrays of paraboloidal concentrators. Wind tunnel tests have been performed on model heliostat arrays, but there are important aerodynamic differences between heliostats and paraboloidal dishes.

Roschke, E. J.

1984-05-01T23:59:59.000Z

289

Balancing of Wind Power.  

E-Print Network (OSTI)

?? In the future, renewable energy share, especially wind power share, in electricity generation is expected to increase. Due to nature of the wind, wind… (more)

Ülker, Muhammed Akif

2011-01-01T23:59:59.000Z

290

Wind lift generator  

SciTech Connect

A wind lift generator includes a housing structure formed by a pair of spaced apart plates mounted on support structure for pivotal rotation about a vertical axis at the forward end thereof for orienting into the wind, and said plates supporting a plurality of coaxially disposed sprockets arranged to support a pair of spaced apart drive chains in a quadrilateral configuration with lift foils connected and supported between the chains with the quadrilateral chain configuration supporting the chain for an initial lift mode at the forward end of the housing, followed by a direct impact mode extending from the front of the housing upward and backward to the rear of the housing and a negative lift mode extending from the top rear of the housing to the bottom with the vanes returning via a neutral mode to the front of the housing for repeating the lift cycle. A suitable electrical generator is driven from one or more shafts of the assembly driven by the drive chains.

Herman, G. R.; Martin, W. A.

1985-08-20T23:59:59.000Z

291

Wind-Stress Coefficients at Light Winds  

Science Conference Proceedings (OSTI)

The increase of the wind-stress coefficient with wind velocity was found to start with winds as light as 3 m s?1, below which, following the formula for aerodynamically smooth flows, the wind-stress coefficient decreases as the wind velocity ...

Jin Wu

1988-12-01T23:59:59.000Z

292

Active curve axis Gaussian mixture models  

Science Conference Proceedings (OSTI)

Gaussian Mixture Models (GMM) have been broadly applied for the fitting of probability density function. However, due to the intrinsic linearity of GMM, usually many components are needed to appropriately fit the data distribution, when there are curve ... Keywords: AcaG, AcaGMM, Active curve axis, EM, Finite mixture models, GMM, Unsupervised learning

Baibo Zhang; Changshui Zhang; Xing Yi

2005-12-01T23:59:59.000Z

293

Wind loading on solar collectors  

DOE Green Energy (OSTI)

The present design methodology for the determination of wind loading on the various solar collectors has been reviewed and assessed. The total force coefficients of flat plates of aspect ratios 1.0 and 3.0, respectively, at various angles of attack obtained by using the guidelines of the ANSI A58.1-1982, have been compared with those obtained by using the methodology of the ASCE Task Committee, 1961, and the experimental results of the full-scale test of heliostats by Peglow. The turbulent energy spectra, currently employed in the building code, are compared with those of Kaimal et al., Lumley, and Ponofsky for wind velocities of 20.0 m/s and 40.24 m/s at an elevation of 9.15 m. The longitudinal spectra of the building code overestimates the Kaimal spectra in the frequency range of 0.007 Hz to 0.08 Hz and underestimates beyond the frequency of 0.08 Hz. The peak angles of attack, on the heliostat, stowed in horizontal position, due to turbulent vertical and lateral components of wind velocity, have been estimated by using Daniel's methodology for three wind velocities and compared with the value suggested by the code. The experimental results of a simple test in the laboratory indicate the feasibility of decreasing the drag forces of the flat plate by reducing the solidity ratio.

Bhaduri, S.; Murphy, L.M.

1985-06-01T23:59:59.000Z

294

Variational Analysis for Airborne Conically Scanned Doppler Lidar to Retrieve Mesoscale Wind Fields  

Science Conference Proceedings (OSTI)

An airborne pulsed Doppler lidar implementing a downlooking conical scan rotating around the vertical axis is under development. The information contained in the measured radial velocities is studied to assess the capacity to retrieve the 3D wind ...

Alain Dabas; Julie Périn; Pierre H. Flamant

1997-10-01T23:59:59.000Z

295

Wind turbine  

DOE Patents (OSTI)

A wind turbine of the type having an airfoil blade (15) mounted on a flexible beam (20) and a pitch governor (55) which selectively, torsionally twists the flexible beam in response to wind turbine speed thereby setting blade pitch, is provided with a limiter (85) which restricts unwanted pitch change at operating speeds due to torsional creep of the flexible beam. The limiter allows twisting of the beam by the governor under excessive wind velocity conditions to orient the blades in stall pitch positions, thereby preventing overspeed operation of the turbine. In the preferred embodiment, the pitch governor comprises a pendulum (65,70) which responds to changing rotor speed by pivotal movement, the limiter comprising a resilient member (90) which engages an end of the pendulum to restrict further movement thereof, and in turn restrict beam creep and unwanted blade pitch misadjustment.

Cheney, Jr., Marvin C. (Glastonbury, CT)

1982-01-01T23:59:59.000Z

296

Sand-control alternatives for horizontal wells  

SciTech Connect

This paper reports that it has been well documented that horizontal completions increase production rates, as much as two to five times those of conventional techniques, because more of the producing formation is exposed to the wellbore. Although productivity improvements are highly sensitive to reservoir parameters, it is becoming generally accepted that optimum horizontal lengths will be 2,000 to 4,000 ft. The length of these completions generally causes the velocity of the fluid at the sandface to be an order of magnitude less than that observed in conventional completions. Because drag forces contributed to sand production, horizontal wells can produce at higher sand-free flow rates than conventional completions in the same reservoir. While it is frequently argued that horizontal wells do not need sand control, the potential for sand production increases significantly as reserves deplete and rock stresses increase. This is becoming more evident today in several major North Sea oil fields with conventional completions. Also, many unconsolidated formations produce sand for the first time with the onset of water production, a typical problem in such areas as the Gulf of Mexico. Operators must decide whether to implement sand control in the original horizontal-completion program because of an immediate concern or because the potential exists for a problem to arise as the well matures.

Zaleski, T.E. Jr. (Baker Sand Control (US))

1991-05-01T23:59:59.000Z

297

New England Wind Forum: Wind Power Economics  

Wind Powering America (EERE)

State Activities Projects in New England Building Wind Energy in New England Wind Resource Wind Power Technology Economics Cost Components Determining Factors Influencing Wind Economics in New England How does wind compare to the cost of other electricity options? Markets Siting Policy Technical Challenges Issues Small Wind Large Wind Newsletter Perspectives Events Quick Links to States CT MA ME NH RI VT Bookmark and Share Wind Power Economics Long-Term Cost Trends Since the first major installations of commercial-scale wind turbines in the 1980s, the cost of energy from wind power projects has decreased substantially due to larger turbine generators, towers, and rotor lengths; scale economies associated with larger projects; improvements in manufacturing efficiency, and technological advances in turbine generator and blade design. These technological advances have allowed for higher generating capacities per turbine and more efficient capture of wind, especially at lower wind speeds.

298

New England Wind Forum: Large Wind  

Wind Powering America (EERE)

Small Wind Small Wind Large Wind Newsletter Perspectives Events Quick Links to States CT MA ME NH RI VT Bookmark and Share Large Wind When establishing wind farms, wind energy developers generally approach landowners where they want to build. Interest in wind farms is frequently spurred by external pressures such as tax and other financial incentives and legislative mandates. Since each situation is influenced by local policies and permitting, we can only provide general guidance to help you learn about the process of installing wind turbines. Publications Wind Project Development Process Permitting of Wind Energy Facilities: A Handbook. (August 2002). National Wind Coordinating Collaborative. Landowner Frequently Asked Questions and Answers. (August 2003). "State Wind Working Group Handbook." pp. 130-133.

299

NREL: Wind Research - International Wind Resource Maps  

NLE Websites -- All DOE Office Websites (Extended Search)

Wind Resource Maps NREL is helping to develop high-resolution projections of wind resources worldwide. This allows for more accurate siting of wind turbines and has led to the...

300

NREL: Wind Research - Wind Project Development Updates  

NLE Websites -- All DOE Office Websites (Extended Search)

Wind Project Development Updates A 2.3 megawatt Siemens wind turbine nacelle on route to the Record Hill Wind project in Roxbury, Maine. January 14, 2013 As a result of the...

Note: This page contains sample records for the topic "horizontal axis wind" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Horizontal stirring in the global ocean  

E-Print Network (OSTI)

Horizontal mixing and the distribution of coherent structures in the global ocean are analyzed using Finite-Size Lyapunov Exponents (FSLE), computed for the surface velocity field derived from the Ocean general circulation model For the Earth Simulator (OFES). FSLEs measure horizontal stirring and dispersion; additionally, the transport barriers which organize the oceanic flow can roughly be identified with the ridges of the FSLE field. We have performed a detailed statistical study, particularizing for the behaviour of the two hemispheres and different ocean basins. The computed Probability Distributions Functions (PDFs) of FSLE are broad and asymmetric. Horizontal mixing is generally more active in the northern hemisphere than in the southern one. Nevertheless the Southern Ocean is the most active ocean, and the Pacific the less active one. A striking result is that the main currents can be classified in two 'activity classes': Western Boundary Currents, which have broad PDFs with large FSLE values, and Eas...

Hernández-Carrasco, I; Hernández-García, E; Turiel, A

2011-01-01T23:59:59.000Z

302

Topic: Wind Engineering  

Science Conference Proceedings (OSTI)

Topic: Wind Engineering. Forty-Fourth Meeting of the UJNR Panel on Wind and Seismic Effects. NIST researchers collected ...

2011-08-31T23:59:59.000Z

303

Extreme Wind Speeds: Publications  

Science Conference Proceedings (OSTI)

... "Algorithms for Generating Large Sets of Synthetic Directional Wind Speed Data for Hurricane, Thunderstorm, and Synoptic Winds," NIST Technical ...

2013-08-19T23:59:59.000Z

304

NREL: Wind Research - Offshore Wind Research  

NLE Websites -- All DOE Office Websites (Extended Search)

Options Site Map Printable Version Offshore Standards and Testing NREL's Offshore Wind Testing Capabilities 35 years of wind turbine testing experience Custom high speed data...

305

High payload six-axis load sensor  

DOE Patents (OSTI)

A repairable high-payload six-axis load sensor includes a table, a base, and at least three shear-pin load transducers removably mounted between the table and the base. Removable mounting permits easy replacement of damaged shear pins. Preferably, the shear-pin load transducers are responsive to shear forces imparted along the two axes perpendicular to an axis of minimum sensitivity characteristic of the transducer. Responsive to an applied shear force, each shear-pin load transducer can produce an electrical signal proportional to the reaction force. The load sensor can further include a structure for receiving the proportional electrical signals and computing the applied load corresponding to the proportional electrical signals. The computed load can be expressed in terms of a three-dimensional XYZ Cartesian coordinate system.

Jansen, John F. (Knoxville, TN); Lind, Randall F. (Knoxville, TN)

2003-01-01T23:59:59.000Z

306

NREL: Wind Research - Small Wind Turbine Development  

NLE Websites -- All DOE Office Websites (Extended Search)

Small Wind Turbine Development Small Wind Turbine Development A photo of Southwest Windpower's Skystream wind turbine in front of a home. PIX14936 Southwest Windpower's Skystream wind turbine. A photo of the Endurance wind turbine. PIX15006 The Endurance wind turbine. A photo of the Atlantic Orient Corporation 15/50 wind turbine at the National Wind Technology Center. PIX07301 The Atlantic Orient Corporation 15/50 wind turbine at the National Wind Technology Center. NREL supports continued market expansion of small wind turbines by funding manufacturers through competitive solicitations (i.e., subcontracts and/or grants) to refine prototype systems leading to commercialization. Learn more about the turbine development projects below. Skystream NREL installed and tested an early prototype of this turbine at the

307

NREL: Wind Research - Small Wind Turbine Webinars  

NLE Websites -- All DOE Office Websites (Extended Search)

Small Wind Turbine Webinars Small Wind Turbine Webinars Here you will find webinars about small wind turbines that NREL hosted. Introducing WindLease(tm): Making Wind Energy Affordable NREL and the American Solar Energy Society (ASES) Wind Division co-hosted this webinar. (Text Version.) Date: August 1, 2013 Run Time: 40 minutes Joe Hess, VP of Business Development at United Wind, described United Wind's WindQuote and WindLease Program and explained the process from the dealer's and consumer's perspective. Texas Renewable Energy Industries Association NREL and the American Solar Energy Society (ASES) Wind Division co-hosted this webinar. (Text Version). Date: March 7, 2013 Run Time: 1 hour Russel Smith, Texas Renewable Energy Industries Association executive director and co-founder, provided an overview of the trade association

308

New England Wind Forum: Small Wind  

Wind Powering America (EERE)

Wind for Schools Project Funding Case Studies: Thomas Harrison Middle School, Virginia Wind for Schools Project Funding Case Studies: Thomas Harrison Middle School, Virginia August 26, 2013 Workshop Explores Information's Role in Wind Project Siting: A Wind Powering America Success Story November 19, 2012 More News Subscribe to News Updates Events Renewable Energy Market Update Webinar January 29, 2014 Strategic Energy Planning: Webinar February 26, 2014 Introduction to Wind Systems March 10, 2014 More Events Publications 2012 Market Report on Wind Technologies in Distributed Applications August 12, 2013 More Publications Features Sign up for the New England Wind Forum Newsletter. New England Wind Forum About the New England Wind Forum New England Wind Energy Education Project Historic Wind Development in New England State Activities Projects in New England

309

Wind-Driven Ageostrophic Transport in the North Equatorial Countercurrent of the Eastern Pacific at 95°W  

Science Conference Proceedings (OSTI)

Observations of horizontal velocity from two shipboard acoustic Doppler current profilers (ADCPs), as well as wind, temperature, and salinity observations from a cruise during June–July 2001, are used to compute a simplified mean meridional ...

Janet Sprintall; Sean Kennan; Yoo Yin Kim; Peter Niiler

2009-11-01T23:59:59.000Z

310

A Climatological Study of Boundary Layer Wind Speed Using a Meso-?-Scale Higher-Order Closure Model  

Science Conference Proceedings (OSTI)

A mesoscale higher-order closure atmospheric boundary layer model has been used to get more detailed information than is possible from observations regarding horizontal and vertical variations of the wind in an area in southeastern Sweden. To ...

Hans Bergström

1996-08-01T23:59:59.000Z

311

Anomalously warm July 2005 in the northern California Current: Historical context and the significance of cumulative wind stress  

E-Print Network (OSTI)

, and equator- ward currents associated with strong horizontal density gradients develop [Huyer et al., 1979 transition was unusually late: by inspection of buoy wind records it was 24 May 2005, about five weeks later

Pierce, Stephen

312

An Analysis of Wind Fluctuation Statistics Collected under Stable Atmospheric Conditions at Three Sites in Alberta, Canada  

Science Conference Proceedings (OSTI)

Wind fluctuation data collected under stable atmospheric conditions at two prairie sites and a site located near the Rocky Mountain foothills have been analyzed. Results of the analysis show a marked tendency for horizontal fluctuation angles to ...

D. M. Leahey; M. C. Hansen; M. B. Schroeder

1988-06-01T23:59:59.000Z

313

Wind turbine generator with improved operating subassemblies  

DOE Patents (OSTI)

A wind turbine includes a yaw spring return assembly to return the nacelle from a position to which it has been rotated by yawing forces, thus preventing excessive twisting of the power cables and control cables. It also includes negative coning restrainers to limit the bending of the flexible arms of the rotor towards the tower, and stop means on the rotor shaft to orient the blades in a vertical position during periods when the unit is upwind when the wind commences. A pendulum pitch control mechanism is improved by orienting the pivot axis for the pendulum arm at an angle to the longitudinal axis of its support arm, and excessive creep is of the synthetic resin flexible beam support for the blades is prevented by a restraining cable which limits the extent of pivoting of the pendulum during normal operation but which will permit further pivoting under abnormal conditions to cause the rotor to stall.

Cheney, Jr., Marvin C. (24 Stonepost Rd., Glastonbury, CT 06033)

1985-01-01T23:59:59.000Z

314

The Distribution of Cloud Horizontal Sizes  

Science Conference Proceedings (OSTI)

Cloud horizontal size distributions from near-global satellite data, from aircraft, and from a global high-resolution numerical weather prediction model, are presented for the scale range 0.1–8000 km and are shown to be well-represented using a ...

Robert Wood; Paul R. Field

2011-09-01T23:59:59.000Z

315

AIAA 20010064 Multi-Flexible-Body Dynamic Analysis of  

E-Print Network (OSTI)

. and Dijkstra, S., "Modeling of Structural Dynamics of Lagerwey LW-50/750 Wind Turbine," Wind En- gineering, VolAIAA 2001­0064 Multi-Flexible-Body Dynamic Analysis of Horizontal-Axis Wind Turbines Mayuresh J-0150 ABSTRACT A dynamic stability analysis is presented for a horizontal-axis wind turbine modeled as a multi

Patil, Mayuresh

316

A Stochastic Methodology for Regional Wind-Field Modeling  

Science Conference Proceedings (OSTI)

Three-dimensional, regional scale (?1000 km) air-quality simulation models require hourly inputs of U and V wind components for each vertical layer of the model and for each grid cell in the horizontal. The standard North American meteorological ...

Kenneth L. Schere; Carlie J. Coats

1992-12-01T23:59:59.000Z

317

SERI Advanced and Innovative Wind-Energy-Concepts Program  

SciTech Connect

In 1978 the Solar Energy Research Institute (SERI) was given the responsibility of managing the Advanced and Innovative Wind Energy Concepts (AIWEC) Task by the US Department of Energy (DOE). The objective of this program has been to determine the technical and economic potential of advanced wind energy concepts. Assessment and R and D efforts in the AIWEC program have included theoretical performance analyses, wind tunnel testing, and/or costing studies. Concepts demonstrating sufficient potential undergo prototype testing in a Proof-of-Concept research phase. Several concepts, such as the Dynamic Inducer, the Diffuser Augmented wind Turbine, the Electrofluid Dynamic Wind-Driven Generator, the Passive Cyclic Pitch concept, and higher performance airfoil configurations for vertical axis wind turbines, have recently made significant progress. The latter has currently reached the Proof-of-Concept phase. The present paper provides an overview of the technical progress and current status of these concepts.

Mitchell, R.L.; Jacobs, E.W.

1983-06-01T23:59:59.000Z

318

NREL: Wind Research - Site Wind Resource Characteristics  

NLE Websites -- All DOE Office Websites (Extended Search)

Site Wind Resource Characteristics Site Wind Resource Characteristics A graphic showing the location of National Wind Technology Center and its wind power class 2. Click on the image to view a larger version. Enlarge image This graphic shows the wind power class at the National Wind Technology Center. You can download a printable copy. The National Wind Technology Center (NWTC) is on the Great Plains just miles from the Rocky Mountains. The site is flat and covered with short grasses. The terrain and lack of obstructions make the site highly suitable for testing wind turbines. Take a tour of the NWTC and its facilities to better understand its location and layout. Another prime feature of the NWTC is the strong directionality of the wind - most of the strong winds come within a few degrees of 285°. West of

319

NREL: Wind Research - Offshore Wind Research  

NLE Websites -- All DOE Office Websites (Extended Search)

Offshore Wind Research Offshore Wind Research Photo of a European offshore wind farm. Early progress in European Offshore Wind Energy over the last decade provides a glimpse into the vast potential of the global offshore resource. For more than eight years, NREL has worked with the Department of Energy to become an international leader in offshore wind energy research. Capabilities NREL's offshore wind capabilities focus on critical areas that reflect the long-term needs of the offshore wind energy industry and the U.S. Department of Energy including: Offshore Design Tools and Methods Offshore Standards and Testing Energy Analysis of Offshore Systems Offshore Wind Resource Characterization Grid Integration of Offshore Wind Key Research NREL documented the status of offshore wind energy in the United States in

320

Horizon Wind  

E-Print Network (OSTI)

The Washington Department of Fish and Wildlife (WDFW) does not have regulatory authority specific to wind power development at this time. WDFW is an agency with environmental expertise as provided for through the Washington Administrative Code (WAC) 197-11-920. Comments related to environmental impacts are provided to regulatory authorities through the State Environmental Policy Act (SEPA) Revised Code of Washington (RCW) 43.21C review process.

Cover Photo; Nina Carter; Heath Packard; Lisa Paribello; Craig Dublanko; Dana Peck; Nicole Hughes; Bill Robinson; Robert Kruse; Arlo Corwin; Joe Buchanan; Ted Clausing; Eric Cummins; Travis Nelson; Eric Pentico; Mike Ritter; Jeff Tayer; James Watson; William Weiler; David Mcclure

2009-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "horizontal axis wind" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Utility Wind Integration Group Distributed Wind/Solar Interconnection...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Utility Wind Integration Group Distributed WindSolar Interconnection Workshop Utility Wind Integration Group Distributed WindSolar Interconnection Workshop May 21, 2013 8:00AM...

322

The Wind Energy Outlook Scenarios 1 India Wind Energy  

E-Print Network (OSTI)

1 ?Status of wind energy in India ????????????????????6 Wind energy in India????????????????????????????????????????????????????????????????????????????????????7 Wind power resource assessment?????????????????????????????????????????????????????????6 Wind power installations by state?????????????????????????????????????????????????????????8

unknown authors

2012-01-01T23:59:59.000Z

323

Horizontal Wavenumber Spectra of Vertical Vorticity and Horizontal Divergence in the Upper Troposphere and Lower Stratosphere  

Science Conference Proceedings (OSTI)

The author shows that the horizontal two-point correlations of vertical vorticity and the associated vorticity wavenumber spectrum can be constructed from previously measured velocity structure functions in the upper troposphere and lower ...

Erik Lindborg

2007-03-01T23:59:59.000Z

324

Observational Study of Wind Channeling within the St. Lawrence River Valley  

Science Conference Proceedings (OSTI)

The presence of orography can lead to thermally and dynamically induced mesoscale wind fields. The phenomenon of channeling refers to the tendency for the winds within a valley to blow more or less parallel to the valley axis for a variety of ...

Marco L. Carrera; John R. Gyakum; Charles A. Lin

2009-11-01T23:59:59.000Z

325

Energy Basics: Wind Power Animation  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Energy Basics Renewable Energy Printable Version Share this resource Biomass Geothermal Hydrogen Hydropower Ocean Solar Wind Wind Turbines Wind Resources Wind Power...

326

Energy Basics: Wind Energy Resources  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Energy Basics Renewable Energy Printable Version Share this resource Biomass Geothermal Hydrogen Hydropower Ocean Solar Wind Wind Turbines Wind Resources Wind Energy...

327

Energy Basics: Wind Energy Technologies  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Energy Basics Renewable Energy Printable Version Share this resource Biomass Geothermal Hydrogen Hydropower Ocean Solar Wind Wind Turbines Wind Resources Wind Energy...

328

Energy Basics: Wind Energy Technologies  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Photo of a hilly field, with six visible wind turbines spinning in the wind. Wind energy technologies use the energy in wind for practical purposes such as generating...

329

Solar Wind | Open Energy Information  

Open Energy Info (EERE)

Wind Jump to: navigation, search Name Solar Wind Place Krasnodar, Romania Zip 350000 Sector Solar, Wind energy Product Russia-based PV product manufacturer. Solar Wind manufactures...

330

EERE: Wind Program Home Page  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

wind projects and offshore wind resource potential. Offshore Wind R&D DOE makes strategic research & deployment investments to launch domestic offshore wind industry....

331

2011 Wind Technologies Market Report  

E-Print Network (OSTI)

A. 2010. Impact of Wind Energy Installations on DomesticUniversity. American Wind Energy Association (AWEA). 2012a.D.C. : American Wind Energy Association. American Wind

Bolinger, Mark

2013-01-01T23:59:59.000Z

332

2011 Wind Technologies Market Report  

E-Print Network (OSTI)

and K. Porter. 2011. Wind Power and Electricity Markets.41 6. Wind Power Priceat Various Levels of Wind Power Capacity Penetration Wind

Bolinger, Mark

2013-01-01T23:59:59.000Z

333

Wind energy conversion. Volume X. Aeroelastic stability of wind turbine rotor blades  

DOE Green Energy (OSTI)

The nonlinear equations of motion of a general wind turbine rotor blade are derived from first principles. The twisted, tapered blade may be preconed out of the plane of rotation, and its root may be offset from the axis of rotation by a small amount. The aerodynamic center, center of mass, shear center, and area centroid are distinct in this derivation. The equations are applicable to studies of forced response or of aeroelastic flutter, however, neither gravity forcing, nor wind shear and gust forcing are included. The equations derived are applied to study the aeroelastic stability of the NASA-ERDA 100 kW wind turbine, and solved using the Galerkin method. The numerical results are used in conjunction with a mathematical comparison to prove the validity of an equivalent hinge model developed by the Wind Energy Conversion Project at the Massachusetts Institute of Technology.

Wendell, J.

1978-09-01T23:59:59.000Z

334

Theoretical tool movement required to diamond turn an off-axis paraboloid on axis  

SciTech Connect

High-quality, off-axis parabolic reflectors, required by the CTR and laser-fusion programs at Lawrence Livermore Laboratory (LLL) and other ERDA laboratories, are currently manufactured by hand. There are several drawbacks to this method, including lead times of up to a year, costs in excess of $75,000 for a small reflector, and unsatisfactory limits to the tolerances obtainable. This situation has led to a search for cheaper and more accurate methods of manufacturing off-axis paraboloids. An alternative method, turning the workpiece about its axis on a diamond-turning machine, is presented, and the equations describing the necessary tool movement are derived. A discussion of a particular case suggests that the proposed technique is feasible. (auth)

Thompson, D.C.

1975-12-19T23:59:59.000Z

335

Wind Vision Wind Farm | Open Energy Information  

Open Energy Info (EERE)

Wind Farm Wind Farm Jump to: navigation, search Name Wind Vision Wind Farm Facility Wind Vision Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner Wind Vision Developer Wind Vision Location St. Ansgar IA Coordinates 43.348224°, -92.888816° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":43.348224,"lon":-92.888816,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

336

High Winds Wind Farm | Open Energy Information  

Open Energy Info (EERE)

Winds Wind Farm Winds Wind Farm Jump to: navigation, search Name High Winds Wind Farm Facility High Winds Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner NextEra Energy Resources Developer NextEra Energy Resources Energy Purchaser PPM Energy Inc Location Solano County CA Coordinates 38.124844°, -121.764915° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":38.124844,"lon":-121.764915,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

337

NREL: Wind Research - Small Wind Turbine Research  

NLE Websites -- All DOE Office Websites (Extended Search)

Small Wind Turbine Research Small Wind Turbine Research The National Renewable Energy Laboratory and U.S. Department of Energy (NREL/DOE) Small Wind Project's objectives are to reduce barriers to wind energy expansion, stabilize the market, and expand the number of small wind turbine systems installed in the United States. "Small wind turbine" refers to a turbine smaller than or equal to 100 kilowatts (kW). "Distributed wind" includes small and midsize turbines (100 kW through 1 megawatt [MW]). Since 1996, NREL's small wind turbine research has provided turbine testing, turbine development, and prototype refinement leading to more commercially available small wind turbines. Work is conducted under the following areas. You can also learn more about state and federal policies

338

Horizontal drilling in shallow, geologically complex reservoirs  

Science Conference Proceedings (OSTI)

The objective of this project is to test the concept that multiple hydraulic fracturing from a directionally-drilled horizontal well, using the medium radius build rate method, can increase gas production sufficiently to justify economic viability over conventional stimulated vertical wells. The test well is located in Yuma County, Colorado, in a favorable area of established production to avoid exploration risks. This report presents: background information; project description which covers location selection/geologic considerations; and preliminary work plan. (AT)

Venable, S.D.

1992-01-01T23:59:59.000Z

339

Horizontal drilling in shallow, geologically complex reservoirs  

Science Conference Proceedings (OSTI)

The objective of this project is to test the concept that multiple hydraulic fracturing from a directionally-drilled horizontal well, using the medium radius build rate method, can increase gas production sufficiently to justify economic viability over conventional stimulated vertical wells. The test well is located in Yuma County, Colorado, in a favorable area of established production to avoid exploration risks. This report presents: background information; project description which covers location selection/geologic considerations; and preliminary work plan. (AT)

Venable, S.D.

1992-10-01T23:59:59.000Z

340

NREL: Wind Research - Information and Outreach  

NLE Websites -- All DOE Office Websites (Extended Search)

small wind systems. Printable Version Wind Research Home Capabilities Projects Offshore Wind Research Large Wind Turbine Research Midsize Wind Turbine Research Small Wind Turbine...

Note: This page contains sample records for the topic "horizontal axis wind" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Portable top drive cuts horizontal drilling costs  

SciTech Connect

Economic analysis of a seven-well, long-reach horizontal drilling program into an unconsolidated, heavy-oil-bearing reservoir in Winter field near the Alberta/Saskatchewan border in Canada reveals that -- in the right application -- renting a portable top drive drilling system can reduce total drilling costs. Use of the portable top drive combined with other cost-saving measures enabled Saskoil, one of Canada`s larger independents, to drill more cheaply, on a cost-per-meter basis, in 1993 than in 1992. This was despite significant rental rates for drilling rigs and directional drilling services caused by increased demand in Western Canada. Total cost savings of 10% on wells that would otherwise cost in the (C) $500,000 range are believed realistic. Based on this year`s performance, Saskoil recommends top drive for the company`s future horizontal wells in this area. This article describes the operator`s horizontal well program, advantages of top drive in that program and how it was installed and applied. Estimated time savings for six wells, plus other ways top drive can cut costs and improve operations are discussed.

Jackson, B. [Saskoil, Regina, Saskatchewan (Canada); Yager, D. [Tesco Drilling Tech., Calgary, Alberta (Canada)

1993-11-01T23:59:59.000Z

342

High accuracy diffuse horizontal irradiance measurements without a shadowband  

DOE Green Energy (OSTI)

The standard method for measuring diffuse horizontal irradiance uses a fixed shadowband to block direct solar radiation. This method requires a correction for the excess skylight blocked by the band, and this correction varies with sky conditions. Alternately, diffuse horizontal irradiance may be calculated from total horizontal and direct normal irradiance. This method is in error because of angular (cosine) response of the total horizontal pyranometer to direct beam irradiance. This paper describes an improved calculation of diffuse horizontal irradiance from total horizontal and direct normal irradiance using a predetermination of the angular response of the total horizontal pyranometer. We compare these diffuse horizontal irradiance calculations with measurements made with a shading-disk pyranometer that shields direct irradiance using a tracking disk. Results indicate significant improvement in most cases. Remaining disagreement most likely arises from undetected tracking errors and instrument leveling.

Schlemmer, J.A; Michalsky, J.J.

1995-12-31T23:59:59.000Z

343

Aerodynamic interference between two Darrieus wind turbines  

DOE Green Energy (OSTI)

The effect of aerodynamic interference on the performance of two curved bladed Darrieus-type vertical axis wind turbines has been calculated using a vortex/lifting line aerodynamic model. The turbines have a tower-to-tower separation distance of 1.5 turbine diameters, with the line of turbine centers varying with respect to the ambient wind direction. The effects of freestream turbulence were neglected. For the cases examined, the calculations showed that the downwind turbine power decrement (1) was significant only when the line of turbine centers was coincident with the ambient wind direction, (2) increased with increasing tipspeed ratio, and (3) is due more to induced flow angularities downstream than to speed deficits near the downstream turbine.

Schatzle, P.R.; Klimas, P.C.; Spahr, H.R.

1981-04-01T23:59:59.000Z

344

Horizontal drilling boosts Pennsylvania’s natural gas production ...  

U.S. Energy Information Administration (EIA)

Between 2009 and 2011, Pennsylvania's natural gas production more than quadrupled due to expanded horizontal drilling combined with hydraulic fracturing.

345

Method of making a wooden wind turbine blade  

DOE Patents (OSTI)

A wooden wind turbine blade is formed by laminating wood veneer in a compression mold having the exact curvature needed for one side of the blade, following which the other side of the blade is ground flat along its length but twisted with respect to the blade axis.

Coleman, Clint (Warren, VT)

1984-01-01T23:59:59.000Z

346

Method of making a wooden wind turbine blade  

DOE Patents (OSTI)

A wooden wind turbine blade is formed by laminating wood veneer in a compression mold having the exact curvature needed for one side of the blade, following which the other side of the blade is ground flat along its length but twisted with respect to the blade axis. 8 figs.

Coleman, C.

1984-08-14T23:59:59.000Z

347

Wind Power Today  

SciTech Connect

Wind Power Today is an annual publication that provides an overview of the wind energy research conducted by the U.S. Department of Energy Wind and Hydropower Technologies Program.

2006-05-01T23:59:59.000Z

348

Wind Power Today  

DOE Green Energy (OSTI)

Wind Power Today is an annual publication that provides an overview of the wind energy research conducted by the U.S. Department of Energy Wind and Hydropower Technologies Program.

Not Available

2007-05-01T23:59:59.000Z

349

Wind: wind power density GIS data at 50m above ground and 1km resolution  

Open Energy Info (EERE)

China from NREL China from NREL Dataset Summary Description (Abstract): Raster GIS data, exported as BIL file, 50 m wind power density for eastern China. (Purpose): To provide information on the wind resource potential in eastern China. Values range from 0 to 3079 W/m2. (Supplemental Information): The modeling regions do not completely cover eastern China. Projection Parameters Projection LAMBERT_AZIMUTHAL Datum WGS84 Zunits METERS Units METERS Spheroid DEFINED Major Axis 6370997.00000 Minor Axis 0.00000 Parameters: radius of the sphere of reference 6370997.00000 Continue? longitude of center of projection 119 0 0.00 latitude of center of projection 33 30 0.000 false easting (meters) 0.00000 false northing (meters) 0.00000 Spatial Information Raster: Number of Columns: 2658 Number of Rows: 3926 Pixel

350

Wind: wind power density maps at 50 m above ground and 1km resolution for  

Open Energy Info (EERE)

eastern China from NREL eastern China from NREL Dataset Summary Description (Abstract): PDF maps of Eastern China wind mapping. (Purpose): To provide information on the wind resource potential in eastern China. Includes maps of full mapping region, and 15 sub-regions. (Supplemental Information): The modeling regions do not completely cover eastern China. Projection Parameters Projection LAMBERT_AZIMUTHAL Datum WGS84 Z-units METERS Units METERS Spheroid DEFINED Major Axis 6370997.00000 Minor Axis 0.00000 Parameters: radius of the sphere of reference 6370997.00000 Continue? longitude of center of projection 119 0 0.00 latitude of center of projection 33 30 0.000 false easting (meters) 0.00000 false northing (meters) 0.00000 Spatial Information Raster: Number of Columns: 2658 Number of Rows: 3926

351

Wind energy manual  

E-Print Network (OSTI)

Objectives: The course introduces principles of wind power production, design of wind turbines, location and design of wind farms, control of turbines and wind farms, predictive modeling, diagnostics, operations and maintenance, condition monitoring, health monitoring and of turbine components and systems, wind farm performance optimization, and integration of wind power with a grid. The modeling and analysis aspect of the topics discussed in the class will be illustrated with examples and case studies. Textbook: References:

A. Vieira; Da Rosa; Fundamentals Renewable; Energy Processes; San Diego; Jacob Kirpes; Small Wind

2013-01-01T23:59:59.000Z

352

NREL: Wind Research - Testing  

NLE Websites -- All DOE Office Websites (Extended Search)

Testing Photo of a large wind turbine blade sticking out of the structural testing laboratory; it is perpendicular to a building at the National Wind Technology Center. A...

353

Wind | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Assessment and Characterization Defining, measuring, and forecasting land-based and offshore wind resources Environmental Impacts and Siting of Wind Projects Avoiding,...

354

Wind/Hydro Study  

NLE Websites -- All DOE Office Websites (Extended Search)

WindHydro Integration Feasibility Study Announcements (Updated July 8, 2010) The Final WindHydro Integration Feasibility Study Report, dated June 2, 2009, has been submitted to...

355

Wind Energy Technologies  

Energy.gov (U.S. Department of Energy (DOE))

Wind energy technologies use the energy in wind for practical purposes such as generating electricity, charging batteries, pumping water, and grinding grain.

356

Wind for Schools (Poster)  

SciTech Connect

As the United States dramatically expands wind energy deployment, the industry is challenged with developing a skilled workforce and addressing public resistance. Wind Powering America's Wind for Schools project addresses these issues by developing Wind Application Centers (WACs) at universities; WAC students assist in implementing school wind turbines and participate in wind courses, by installing small wind turbines at community "host" schools, by implementing teacher training with interactive curricula at each host school. This poster provides an overview of the first two years of the Wind for Schools project, primarily supporting activities in Colorado, Kansas, Nebraska, South Dakota, Montana, and Idaho.

Baring-Gould, I.

2010-05-01T23:59:59.000Z

357

Wind for Schools (Poster)  

SciTech Connect

As the United States dramatically expands wind energy deployment, the industry is challenged with developing a skilled workforce and addressing public resistance. Wind Powering America's Wind for Schools project addresses these issues by developing Wind Application Centers (WACs) at universities; WAC students assist in implementing school wind turbines and participate in wind courses, by installing small wind turbines at community "host" schools, by implementing teacher training with interactive curricula at each host school. This poster provides an overview of the first two years of the Wind for Schools project, primarily supporting activities in Colorado, Kansas, Nebraska, South Dakota, Montana, and Idaho.

Baring-Gould, I.

2010-05-01T23:59:59.000Z

358

Wind energy bibliography  

DOE Green Energy (OSTI)

This bibliography is designed to help the reader search for information on wind energy. The bibliography is intended to help several audiences, including engineers and scientists who may be unfamiliar with a particular aspect of wind energy, university researchers who are interested in this field, manufacturers who want to learn more about specific wind topics, and librarians who provide information to their clients. Topics covered range from the history of wind energy use to advanced wind turbine design. References for wind energy economics, the wind energy resource, and environmental and institutional issues related to wind energy are also included.

None

1995-05-01T23:59:59.000Z

359

Diablo Winds Wind Farm | Open Energy Information  

Open Energy Info (EERE)

Diablo Winds Wind Farm Diablo Winds Wind Farm Facility Diablo Winds Wind Farm Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner NextEra Energy Resources Developer NextEra Energy Resources Energy Purchaser Pacific Gas & Electric Co Location Altamont Pass CA Coordinates 37.7347°, -121.652° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":37.7347,"lon":-121.652,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

360

NREL: Wind Research - Offshore Wind Resource Characterization  

NLE Websites -- All DOE Office Websites (Extended Search)

Offshore Wind Resource Characterization Offshore Wind Resource Characterization Map of the United States, showing the wind potential of offshore areas across the country. Enlarge image US offshore wind speed estimates at 90-m height NREL scientists and engineers are leading efforts in resource mapping, remote sensor measurement and development, and forecasting that are essential for the development of offshore wind. Resource Mapping For more than 15 years, NREL's meteorologists, engineers, and Geographic Information System experts have led the production of wind resource characterization maps and reports used by policy makers, private industry, and other government organizations to inform and accelerate the development of wind energy in the United States. Offshore wind resource data and mapping has strategic uses. As with terrestrial developments, traditional

Note: This page contains sample records for the topic "horizontal axis wind" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

NREL: Wind Research - Midsize Wind Turbine Research  

NLE Websites -- All DOE Office Websites (Extended Search)

Midsize Wind Turbine Research Midsize Wind Turbine Research To facilitate the development and commercialization of midsize wind turbines (turbines with a capacity rating of more than 100 kW up to 1 MW), the U.S. Department of Energy (DOE) and NREL launched the Midsize Wind Turbine Development Project. In its latest study, NREL determined that there is a substantial market for midsize wind turbines. One of the most significant barriers to the midsize turbine market is the lack of turbines available for deployment; there are few midsize turbines on the market today. The objectives of the Midsize Wind Turbine Development Project are to reduce the barriers to wind energy expansion by filling an existing domestic technology gap; facilitate partnerships; accelerate maturation of existing U.S. wind energy businesses; and incorporate process improvement

362

Commonwealth Wind Incentive Program – Micro Wind Initiative  

Energy.gov (U.S. Department of Energy (DOE))

Through the Commonwealth Wind Incentive Program – Micro Wind Initiative the Massachusetts Clean Energy Center (MassCEC) offers rebates of up to $4/W with a maximum of $130,000 for design and...

363

Wind characteristics for agricultural wind energy applications  

SciTech Connect

Wind energy utilization in agriculture can provide a potentially significant savings in fuel oil consumption and ultimately a cost savings to the farmer. A knowledge of the wind characteristics within a region and at a location can contribute greatly to a more efficient and cost-effective use of this resource. Current research indicates that the important wind characteristics include mean annual wind speed and the frequency distribution of the wind, seasonal and diurnal variations in wind speed and direction, and the turbulent and gustiness characteristics of the wind. Further research is underway to provide a better definition of the total wind resource available, improved methods for siting WECS and an improved understanding of the environment to which the WECS respond.

Renne, D. S.

1979-01-01T23:59:59.000Z

364

Wind Power Today: Federal Wind Program Highlights  

DOE Green Energy (OSTI)

Wind Power Today is an annual publication that provides an overview of the wind research conducted under the U.S. Department of Energy's Wind and Hydropower Technologies Program. The purpose of Wind Power Today is to show how DOE supports wind turbine research and deployment in hopes of furthering the advancement of wind technologies that produce clean, low-cost, reliable energy. Content objectives include: educate readers about the advantages and potential for widespread deployment of wind energy; explain the program's objectives and goals; describe the program's accomplishments in research and application; examine the barriers to widespread deployment; describe the benefits of continued research and development; facilitate technology transfer; and attract cooperative wind energy projects with industry.

Not Available

2005-04-01T23:59:59.000Z

365

2008 WIND TECHNOLOGIES MARKET REPORT  

E-Print Network (OSTI)

policy support for other renewable energy sources, wind mayrenewable energy and climate policy initiatives. With wind

Bolinger, Mark

2010-01-01T23:59:59.000Z

366

Zhongshan Yixiong Wind Power Co Ltd | Open Energy Information  

Open Energy Info (EERE)

Yixiong Wind Power Co Ltd Yixiong Wind Power Co Ltd Jump to: navigation, search Name Zhongshan Yixiong Wind Power Co Ltd Place Zhongshan, Guangdong Province, China Sector Wind energy Product A producer for vertical axis wind turbine. Coordinates 22.516701°, 113.366699° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":22.516701,"lon":113.366699,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

367

Simulation of ENSO-Related Surface Winds in the Tropical Pacific by an Atmospheric General Circulation Model Forced by Observed Sea Surface Temperatures  

Science Conference Proceedings (OSTI)

The authors present the simulation of the tropical Pacific surface wind variability by a low-resolution (R15 horizontal resolution and 18 vertical levels) version of the Center for Ocean-Land-Atmosphere Interactions, Maryland, general circulation ...

B. N. Goswami; V. Krishnamurthy; N. H. Saji

1995-06-01T23:59:59.000Z

368

Assimilation of T-TREC-Retrieved Winds from Single-Doppler Radar with an Ensemble Kalman Filter for the Forecast of Typhoon Jangmi (2008)  

Science Conference Proceedings (OSTI)

A tropical cyclone (TC) circulation Tracking Radar Echo by Correlation technique (T-TREC) developed recently is applied to derive horizontal winds from single Doppler radar reflectivity Z data (combined with radial velocity Vr data when available)...

Mingjun Wang; Ming Xue; Kun Zhao; Jili Dong

369

A comparison of on-axis and off-axis heliostat alignment strategies  

DOE Green Energy (OSTI)

Heliostat installation and alignment costs will be an important element in future solar power tower projects. The predicted annual performances of on- and-off axis strategies are compared for 95 m{sup 2} flat-glass heliostats and an external, molten-salt receiver. Actual approaches to heliostat alignment that have been used in the past are briefly discussed, and relative strengths and limitations are noted. The optimal approach can vary with the application.

Jones, S.A.

1996-03-01T23:59:59.000Z

370

NREL Combined Experimental Final Report--Phase II  

SciTech Connect

Predicting peak power and loads on a fixed-pitch wind turbine. How does the performance of the airfoil in the wind tunnel differ from the performance of an operating horizontal-axis wind turbine (HAWT)?

Butterfield, C. P.; Musial, W. P.; Scott, G. N.; Simms, D. A.

1992-08-01T23:59:59.000Z

371

West Winds Wind Farm | Open Energy Information  

Open Energy Info (EERE)

West Winds Wind Farm West Winds Wind Farm Facility West Winds Sector Wind energy Facility Type Commercial Scale Wind Facility Status In Service Owner Caithness Developer SeaWest Energy Purchaser Southern California Edison/PacifiCorp Location San Gorgonio CA Coordinates 33.9095°, -116.734° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":33.9095,"lon":-116.734,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

372

Solar and Wind Energy Resource Assessment in Nepal | OpenEI  

Open Energy Info (EERE)

in Nepal in Nepal Dataset Summary Description (Abstract): Global Horizontal Solar Irradiance is developed based on a linear regression model that has been developed to correlate the theoretical and ground measured solar irradiance on the basis of available ground measured Global Horizontal Solar Irradiance at three locations: a) Syangboche (Solukhumbu) b) Pulchowk (Lalitpur) and c) Prakashpur (Sunsari). These locations represent the three different geographical regions: Mountain, Hill and Plain. The model is used for converting the theoretical Global Horizontal Solar Irradiance to actual solar irradiance in 15 meteorological stations spread throughout the country. Interpolating the data obtained at these stations, a map has been developed using ArcView GIS software. The existing methodology for projecting wind speedat 2m height from DHM meteorological station data to 10m height, shows a deviated figures. In other to develop wind map, valid methodology is required which can project the low height wind speed to higher heights. The projected data (Thini and Thakmarpha) when

373

Applications: Operational wind turbines  

E-Print Network (OSTI)

Capability Applications: Operational wind turbines Benefits: Optimize wind turbine performance Summary: Researchers at the Los Alamos National Laboratory (LANL) Intelligent Wind Turbine Program are developing a multi-physics modeling approach for the analysis of wind turbines in the presence of realistic

374

Wind powering America: Iowa  

DOE Green Energy (OSTI)

Wind resources in the state of Iowa show great potential for wind energy development. This fact sheet provides a brief description of the state's wind resources and the financial incentives available for the development of wind energy systems. It also provides a list of contacts for more information.

NREL

2000-04-11T23:59:59.000Z

375

Three-axis particle impact probe  

DOE Patents (OSTI)

Three-axis particle impact probes detect particle impact vectors along x-, y-, and z-axes by means of a head mounted on the outer end of a shaft that is flexibly mounted in silicone rubber at the top of a housing so as to enable motion imparted to the head upon impact to be transmitted to a grounded electrode secured to the shaft within the housing. Excitable electrodes are mounted in the housing in a fixed position, spaced apart from the ground electrode and forming, with the ground electrode, capacitor pairs. Movement of the ground electrode results in changes in capacitance, and these differences in capacitance are used for measurement or derivation of momentum vectors along each of the three axes. In one embodiment, the ground electrode is mounted at the base of the shaft and is secured to a silicone rubber layer at the top of the housing, providing for cantilevered movement. In another embodiment, the shaft is mounted at its mid point in a flexible bushing so that it undergoes pivotal movement around that point.

Fasching, G.E.; Smith, N.S. Jr.; Utt, C.E.

1991-04-02T23:59:59.000Z

376

Wind effects on convective heat loss from a cavity receiver for a parabolic concentrating solar collector  

DOE Green Energy (OSTI)

Tests were performed to determine the convective heat loss characteristics of a cavity receiver for a parabolid dish concentrating solar collector for various tilt angles and wind speeds of 0-24 mph. Natural (no wind) convective heat loss from the receiver is the highest for a horizontal receiver orientation and negligible with the reveler facing straight down. Convection from the receiver is substantially increased by the presence of side-on wind for all receiver tilt angles. For head-on wind, convective heat loss with the receiver facing straight down is approximately the same as that for side-on wind. Overall it was found that for wind speeds of 20--24 mph, convective heat loss from the receiver can be as much as three times that occurring without wind.

Ma, R.Y. [California State Polytechnic Univ., Pomoma, CA (United States). Dept. of Mechanical Engineering

1993-09-01T23:59:59.000Z

377

NREL: Wind Research - Small Wind Site Assessment: Wind Powering...  

NLE Websites -- All DOE Office Websites (Extended Search)

environmental impacts have increased the demand for small wind energy systems for homeowners, schools, businesses, and local governments. Over the past decade, the knowledge,...

378

New England Wind Forum: New England Wind Resources  

Wind Powering America (EERE)

New England Wind Forum About the New England Wind Forum New England Wind Energy Education Project Historic Wind Development in New England State Activities Projects in New England Building Wind Energy in New England Wind Resources Wind Power Technology Economics Markets Siting Policy Technical Challenges Issues Small Wind Large Wind Newsletter Perspectives Events Quick Links to States CT MA ME NH RI VT Bookmark and Share New England Wind Resources Go to the Vermont wind resource map. Go to the New Hampshire wind resource map. Go to the Maine wind resource map. Go to the Massachusetts wind resource map. Go to the Connecticut wind resource map. Go to the Rhode Island wind resource map. New England Wind Resource Maps Wind resources maps of Connecticut, Massachusetts, Maine, New Hampshire, Rhode Island, and Vermont.

379

Wind Powering America  

Wind Powering America (EERE)

These news items are notable additions These news items are notable additions to the Wind Powering America Web site. The Wind Powering America Web site reports recent national and state wind market changes by cataloging wind activities such as wind resource maps, small wind consumer's guides, local wind workshops, news articles, and publications in the areas of policy, public power, small wind, Native Americans, agricultural sector, economic development, public lands, and schools. en-us julie.jones@nrel.gov (Julie Jones) http://www.windpoweringamerica.gov/images/wpa_logo_sm.jpg Wind Powering America http://www.windpoweringamerica.gov/ Nominate an Electric Cooperative for Wind Power Leadership Award by January 15 http://www.windpoweringamerica.gov/filter_detail.asp?itemid=4076 http://www.windpoweringamerica.gov/filter_detail.asp?itemid=4076 Mon, 16

380

Wind energy, offers considerable promise: the wind itself is free,  

E-Print Network (OSTI)

Wind energy, offers considerable promise: the wind itself is free, wind power is clean. One of these sources, wind energy, offers considerable promise: the wind itself is free, wind power is clean, and it is virtually inexhaustible. In recent years, research on wind energy has accelerated

Langendoen, Koen

Note: This page contains sample records for the topic "horizontal axis wind" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

The triple axis spectrometer at the new research reactor OPAL ...  

Science Conference Proceedings (OSTI)

... The triple axis spectrometer at the new research reactor OPAL in Australia. ... The TAS will be based on a thermal beam at the reactor face. ...

382

Solasta aka The Eagle Axis | Open Energy Information  

Open Energy Info (EERE)

search Name Solasta (aka The Eagle Axis) Place Newton, Massachusetts Zip 2458 Sector Efficiency, Solar Product Start-up planning to produce high-efficiency solar cells using...

383

DARHT: Dual-Axis Radiographic Hydrodynamic Test Facility  

NLE Websites -- All DOE Office Websites (Extended Search)

Radiographic Hydrodynamic Test Facility DARHT: Dual-Axis Radiographic Hydrodynamic Test Facility DARHT, supports a critical component of LANL's primary mission: to ensure...

384

Wind Power Outlook 2004  

DOE Green Energy (OSTI)

The brochure, expected to be updated annually, provides the American Wind Energy Association's (AWAE's) up-to-date assessment of the wind industry. It provides a summary of the state of wind power in the U.S., including the challenges and opportunities facing the industry. It provides summary information on the growth of the industry, policy-related factors such as the federal wind energy production tax credit status, comparisons with natural gas, and public views on wind energy.

anon.

2004-01-01T23:59:59.000Z

385

Wind Resource Maps (Postcard)  

DOE Green Energy (OSTI)

The U.S. Department of Energy's Wind Powering America initiative provides high-resolution wind maps and estimates of the wind resource potential that would be possible from development of the available windy land areas after excluding areas unlikely to be developed. This postcard is a marketing piece that stakeholders can provide to interested parties; it will guide them to Wind Powering America's online wind energy resource maps.

Not Available

2011-07-01T23:59:59.000Z

386

Winds Measured by a UHF Doppler Radar and Rawinsondes: Comparisons Made on Twenty-Six Days (August-September 1977) at Arecibo, Puerto Rico  

Science Conference Proceedings (OSTI)

Vertical profiles of horizontal winds in the lower stratosphere and upper troposphere were measured by the UHF Doppler radar at Arecibo, Puerto Rico (18.35°N, 66.75°W) on 26 days in August and September 1977. On comparing these with horizontal ...

Shoichiro Fukao; Toru Sato; Norikazu Yamasaki; Robert M. Harper; Susumu Kato

1982-09-01T23:59:59.000Z

387

Synthesis and Characterization of Co-ZnO Composite  

Science Conference Proceedings (OSTI)

Overview of Microstructural Models Applied to Hot Rolling Mill for Long ... Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades.

388

Negative Thermal Expansion in YInMo3O12  

Science Conference Proceedings (OSTI)

Overview of Microstructural Models Applied to Hot Rolling Mill for Long ... Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades.

389

Lignocellulosic-Based Carbon Fibers from Biofuel Production Wastes  

Science Conference Proceedings (OSTI)

Overview of Microstructural Models Applied to Hot Rolling Mill for Long ... Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades.

390

Mechanical and Microstructural Aspects Observed in 6063 ...  

Science Conference Proceedings (OSTI)

Overview of Microstructural Models Applied to Hot Rolling Mill for Long ... Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades.

391

Stress-Strain Curves for Steel Fiber-Reinforced Concrete in ...  

Science Conference Proceedings (OSTI)

Overview of Microstructural Models Applied to Hot Rolling Mill for Long ... Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades.

392

Three Dimensional (3D) Microstructure Visualization and Modeling ...  

Science Conference Proceedings (OSTI)

Overview of Microstructural Models Applied to Hot Rolling Mill for Long ... Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades.

393

State of the Art in Aluminum Matrix Composites using Fly Ash  

Science Conference Proceedings (OSTI)

Overview of Microstructural Models Applied to Hot Rolling Mill for Long ... Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades.

394

Microstructure Evolution of AA7050 Al Alloy by ECAP  

Science Conference Proceedings (OSTI)

Overview of Microstructural Models Applied to Hot Rolling Mill for Long ... Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades.

395

Deformation and Fracture of an Alpha/Beta Titanium Alloy  

Science Conference Proceedings (OSTI)

Overview of Microstructural Models Applied to Hot Rolling Mill for Long ... Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades.

396

Processing of a Duplex Stainless Steel by Equal Channel Angular ...  

Science Conference Proceedings (OSTI)

Overview of Microstructural Models Applied to Hot Rolling Mill for Long ... Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades.

397

Strain Rate Dependent Response of Rabbit Femur Bones  

Science Conference Proceedings (OSTI)

Overview of Microstructural Models Applied to Hot Rolling Mill for Long ... Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades.

398

Society Changing Needs in Advanced Materials  

Science Conference Proceedings (OSTI)

Overview of Microstructural Models Applied to Hot Rolling Mill for Long ... Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades.

399

Simulation of Nanofoams under Stress and Irradiation Conditions  

Science Conference Proceedings (OSTI)

Overview of Microstructural Models Applied to Hot Rolling Mill for Long ... Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades.

400

Experimental Tests of Vanadium Strength Models at High Pressures ...  

Science Conference Proceedings (OSTI)

Overview of Microstructural Models Applied to Hot Rolling Mill for Long ... Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades.

Note: This page contains sample records for the topic "horizontal axis wind" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Micrometric Solar-Cell Coating Adhesion Characterization by Sub ...  

Science Conference Proceedings (OSTI)

Overview of Microstructural Models Applied to Hot Rolling Mill for Long ... Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades.

402

Stresses within Dislocation Cell Structures: Size Effects versus ...  

Science Conference Proceedings (OSTI)

Overview of Microstructural Models Applied to Hot Rolling Mill for Long ... Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades.

403

Work Hardening Characteristics of TWIP Steel Cold Rolling and ...  

Science Conference Proceedings (OSTI)

Overview of Microstructural Models Applied to Hot Rolling Mill for Long ... Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades.

404

Using Accumulative Roll Bonding to Process Ultrafine Grained ...  

Science Conference Proceedings (OSTI)

Overview of Microstructural Models Applied to Hot Rolling Mill for Long ... Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades.

405

Mechanical and Microstructural Investigation of Autoclaved ...  

Science Conference Proceedings (OSTI)

Overview of Microstructural Models Applied to Hot Rolling Mill for Long ... Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades.

406

Hawaii Zuteck Rotor Project: Compilation of project reports  

DOE Green Energy (OSTI)

Summarizes project to design and build aileron retrofit blades for a 600 kW upwind, teetered rotor, full-span pitch control, horizontal-axis wind turbine.

Zuteck, M.D.; Miller, M.W.

1999-02-25T23:59:59.000Z

407

Material Deformation Dynamics at Ultrahigh Pressures and Strain ...  

Science Conference Proceedings (OSTI)

Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades ... Using the Computational Modelling to Improve Durability of Diesel Engine ...

408

The Neural Network Model using for Predictions Mechanical ...  

Science Conference Proceedings (OSTI)

Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades ... Using the Computational Modelling to Improve Durability of Diesel Engine ...

409

Influence of Environmental Degradation on the Ballistic Behavior of ...  

Science Conference Proceedings (OSTI)

Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades ... Using the Computational Modelling to Improve Durability of Diesel Engine ...

410

Modelling the Pulsed Laser Welding and Cutting for Thin Sheets ...  

Science Conference Proceedings (OSTI)

Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades ... Using the Computational Modelling to Improve Durability of Diesel Engine ...

411

The Impact of Corrosion on Society  

Science Conference Proceedings (OSTI)

Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades ... Using the Computational Modelling to Improve Durability of Diesel Engine ...

412

The Energy Challenge and the Role of Advanced Materials ...  

Science Conference Proceedings (OSTI)

Among the current options for cleaner energy production, many are .... Study of Composite Materials Application for Horizontal Axis Wind Turbine Blades.

413

Site insolation and wind power characteristics: technical report western region (south section)  

DOE Green Energy (OSTI)

This phase of the Site Insolation and Wind Power Characteristics Study was performed to provide statistical information on the expected future availability of solar and wind power at various sites in the Western Region (South Section) of the US Historic data (SOLMET), at 22 National Weather Service stations with hourly solar insolation and collateral meteorological information, were interrogated to provide an estimate of future trends. Solar data are global radiation incident on a horizontal surface, and wind data represent wind power normal to the air flow. Selected insolation and wind power conditions were investigated for their occurrence and persistence, for defined periods of time, on a monthly basis. Global horizontal insolation is related to inclined surfaces at each site. Ratios are provided, monthly, for multiplying global insolation to obtain insolation estimates on south-facing surfaces inclined at different angles with respect to the horizontal. Also, joint probability distribution tables are constructed showing the number of occurrences, out of a finite sample size, of daily average solar and wind power within selected intervals, by month. Information of this nature is intended as an aid to preliminary planning activities for the design and operation of solar and wind energy utilization and conversion systems.

None

1980-08-01T23:59:59.000Z

414

Sinomatech Wind Power Blade aka Sinoma Science Technology Wind...  

Open Energy Info (EERE)

Sinomatech Wind Power Blade aka Sinoma Science Technology Wind Turbine Blade Co Ltd Jump to: navigation, search Name Sinomatech Wind Power Blade (aka Sinoma Science & Technology...

415

NREL: Wind Research - Wind Applications Center Valuable Resource...  

NLE Websites -- All DOE Office Websites (Extended Search)

Wind Applications Center Valuable Resource for Wind for Schools Partners March 14, 2013 Audio with Jerry Hudgins, Nebraska Wind Applications Center Director and Joel Jacobs,...

416

Wind Powering America Webinar: Wind Power Economics: Past, Present...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Power Economics: Past, Present, and Future Trends Wind Powering America Webinar: Wind Power Economics: Past, Present, and Future Trends November 23, 2011 - 1:43pm Addthis Wind...

417

NREL: Wind Research - Small Wind Turbine Independent Testing  

NLE Websites -- All DOE Office Websites (Extended Search)

Wind Research Search More Search Options Site Map Printable Version Small Wind Turbine Independent Testing One of the barriers for the small wind market has been the lack...

418

Discussion of “Ultimate Wind Load Design Gust Wind Speeds ...  

Science Conference Proceedings (OSTI)

... Ind. Aerodyn., 97(3–4), 120–131. Peterka, JA (2001). “Database of peak gust wind speeds, Texas Tech/ CSU.” Extreme winds and wind effects on ...

2013-08-19T23:59:59.000Z

419

Surface wind speed distributions| Implications for climate and wind power.  

E-Print Network (OSTI)

?? Surface constituent and energy fluxes, and wind power depend non-linearly on wind speed and are sensitive to the tails of the wind distribution. Until… (more)

Capps, Scott Blair

2010-01-01T23:59:59.000Z

420

Site insolation and wind power characteristics. Summary report  

DOE Green Energy (OSTI)

Design and operation of either large or small scale solar and wind energy conversion systems should be based, in part, on knowledge of expected solar and wind power trends. For this purpose, historic solar and wind data available at 101 National Weather Service stations were processed statistically. Preliminary planning data are provided for selected daily average solar and wind power conditions occurring and persisting for time periods of interest. Solar data are global radiation incident on a horizontal surface, and wind data represent wind power normal to the air flow. Empirical probabilities were constructed from the historic data to provide a reasonable inference of the chance of similar climatological conditions occurring at any given time in the future. (Diurnal wind power variations were also considered.) Ratios were also generated at each station to relate the global radiation data to insolation on a south-facing surface inclined at various angles. In addition, joint probability distributions were derived to show the proportion of days with solar and wind power within selected intervals.

Bray, R E

1980-08-01T23:59:59.000Z

Note: This page contains sample records for the topic "horizontal axis wind" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Horizontal Drop of 21- PWR Waste Package  

SciTech Connect

The objective of this calculation is to determine the structural response of the waste package (WP) dropped horizontally from a specified height. The WP used for that purpose is the 21-Pressurized Water Reactor (PWR) WP. The scope of this document is limited to reporting the calculation results in-terms of stress intensities. This calculation is associated with the WP design and was performed by the Waste Package Design group in accordance with the ''Technical Work Plan for: Waste Package Design Description for LA'' (Ref. 16). AP-3.12Q, ''Calculations'' (Ref. 1 1) is used to perform the calculation and develop the document. The sketches attached to this calculation provide the potential dimensions and materials for the 21-PWR WP design.

A.K. Scheider

2007-01-31T23:59:59.000Z

422

ERRATUM Energy exchange in an array of vertical-axis wind turbines  

E-Print Network (OSTI)

The calculation of the planform kinetic energy flux in this paper contains an error. The equation stated in the manuscript, Pvert ???Aplanu , is correct. However, a typographical error in the data processing code had the effect of calculating the planform kinetic energy flux using u 2 instead of u. This error caused a quantitative change in the planform kinetic energy flux as can be seen in the revised version of Figure 7. Figure 7. Contours of the power transport due to the planform kinetic energy flux along the centre of the turbine array. The three turbine pairs are indicated as vertical bars. Upon correction, the planform kinetic energy flux is lower than originally stated. In the region in front of the turbine array, it is 2.2 W/m 2 instead of 17 W/m 2. The average planform kinetic energy flux into the turbine array from 2 D downwind of the second turbine pair to 7.5 D downwind of the third sensor pair is 3.4 W/m 2 for the highest sensor position and 0.03 W/m 2 for the lowest sensor position; values of 22 W/m 2 and 0.4 W/m 2, respectively, were stated in the paper. The correction leads to a planform kinetic energy flux of 316 W per turbine pair which is approximately one-third of the power that is extracted by the turbine pair. Furthermore, the corrected results lead to the conclusion that the Frandsen formula gives the better estimate of the planform kinetic energy flux. The Frandsen estimate is off by 76 % while the Lettau is off by a factor of 8.5. While the conclusions of the manuscript are largely unchanged, the corrected data indicate that the planform kinetic energy flux is not sufficient to account for the total power

Matthias Kinzel; Quinn Mulligan; John O. Dabiri

2013-01-01T23:59:59.000Z

423

Measurements of television interference caused by a vertical-axis wind machine. Final subcontract report  

DOE Green Energy (OSTI)

The electromagnetic interference to television reception caused by the 17 m Darreius at Albuquerque, NM, has been studied by carrying out measurements at a number of sites in the vicinity of the VAWT. The rf sources used were the commercial vhf and uhf TV signals available in the area. Ambient field-strength measurements showed that the signals on all TV channels except one were strong, and provided good reception at all test sites. With the antenna (properly) oriented for maximum direct signal, unacceptable interference was observed on some channels at sites out to 33 m from the WT in the forward and backward regions. With the antenna beam directed at the WT, interference varying from slight to violent were observed at all sites on some or all TV channels. A simple theoretical model has been developed for analyzing the TVI produced by a VAWT like the Darrieus. Using the model in conjunction with measured data, an approximate expression for the equivalent scattering area A of the Darrieus has been developed. It is found that A is wavelength (lambda) dependent and varies as lambda/sup 1/2/.

Sengupta, D L; Senior, T B.A.; Ferris, J E

1983-01-01T23:59:59.000Z

424

Sandia Vertical-Axis Wind Turbine Program. Technical quarterly report, October--December 1975  

DOE Green Energy (OSTI)

Information is presented concerning: review of the status of general design efforts in the areas of aerodynamics, structures, systems analysis, and testing; summary of preliminary design details of the proposed 17-m turbine/60-kW generator system for power grid application; and structural analysis and operational test results for the existing 5-m turbine.

Banas, J.F.; Sullivan, W.N. (eds.)

1976-04-01T23:59:59.000Z

425

User's manual for the vertical axis wind turbine performance computer code darter  

DOE Green Energy (OSTI)

The computer code DARTER (DARrieus, Turbine, Elemental Reynolds number) is an aerodynamic performance/loads prediction scheme based upon the conservation of momentum principle. It is the latest evolution in a sequence which began with a model developed by Templin of NRC, Canada and progressed through the Sandia National Laboratories-developed SIMOSS (SSImple MOmentum, Single Streamtube) and DART (SARrieus Turbine) to DARTER.

Klimas, P. C.; French, R. E.

1980-05-01T23:59:59.000Z

426

Computer subroutine for estimating aerodynamic blade loads on Darrieus vertical axis wind turbines. [FORCE code  

DOE Green Energy (OSTI)

An important aspect of structural design of the Darrieus rotor is the determination of aerodynamic blade loads. This report describes a load generator which has been used at Sandia for quasi-static and dynamic rotor analyses. The generator is based on the single streamtube aerodynamic flow model and is constructed as a FORTRAN IV subroutine to facilitate its use in finite element structural models. Input and output characteristics of the subroutine are described and a complete listing is attached as an appendix.

Sullivan, W. N.; Leonard, T. M.

1980-11-01T23:59:59.000Z

427

DEVELOPMENT OF OPTIMUM DESIGN CONFIGURATION AND PERFORMANCE FOR VERTICAL AXIS WIND TURBINE  

E-Print Network (OSTI)

report was prepared as a result of work sponsored by the California Energy Commission (Commission). It does not necessarily represent the views of the Commission, its employees, or the state of California. The Commission, the state of California, its employees, contractors, and subcontractors make no warranty, express or implied, and assume no legal liability for the information in this report; nor does any party represent that the use of this information will not infringe upon privately owned rights. This report has not been approved or disapproved by the Commission nor has the Commission passed upon the accuracy or adequacy of the information in this report. PREFACE The Public Interest Energy Research (PIER) Program supports public interest energy research and development that will help improve the quality of life in California by bringing environmentally safe, affordable and reliable energy services and products to the marketplace. The PIER Program, managed by the California Energy Commission (Commission), annually awards up to $62 million of which $2 million/year is allocated to the Energy Innovation Small Grant (EISG) Program for grants. The EISG Program is administered by the San Diego State

Hamid R. Rahai; Eisg Awardee

2001-01-01T23:59:59.000Z

428

Horizontal flow drilling requires focus on well control  

Science Conference Proceedings (OSTI)

Horizontal wells drilled underbalanced or while flowing must have surface equipment and a blow-out preventer stack specially designed for circulating operations. Functional well control methods for drilling horizontal wells have been developed in specific regions worldwide. Special safety equipment and procedures, however, are still required in most horizontal development applications. The challenge for horizontal drilling development and underbalanced drilling is to overcome the obstacles of government regulation, reduce pollution dangers, and improve personnel and equipment safety. Well control techniques tailored to the demands of each field can help overcome these challenges. Several well control elements must be addressed carefully on each horizontal well: drilling fluid requirements, well control procedures and equipment, and surface equipment and special considerations for handling hydrocarbons produced while drilling. The paper discusses each of these elements for underbalanced horizontal drilling.

Tangedahl, M.J. (RBOP Oil Tools International Inc., Houston, TX (United States))

1994-06-13T23:59:59.000Z

429

Searchlight Wind Energy Project FEIS Appendix E  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

E E Page | E 21B Appendix E: Visual Simulations and Contrast Rating Forms Form 8400-4 UNITED STATES DEPARTMENT OF THE INTERIOR BUREAU OF LAND MANAGEMENT VISUAL CONTRAST RATING WORKSHEET Date June 2, 2009 District Las Vegas Field Office Resource Area Activity (program) Proposed Wind Generation SECTION A. PROJECT INFORMATION 1. Project Name Searchlight Wind Project 4. Location Township 23S Range 63E Section 2 5. Location Sketch 2. Key Observation Point KOP 1 - Railroad Pass Hotel/Casino 3. VRM Class NA SECTION B. CHARACTERISTIC LANDSCAPE DESCRIPTION 1. LAND/WATER 2. VEGETATION 3. STRUCTURES FORM Gently rolling to flat valleys with angular and jagged mountainous features Pixilated and amorphous/patchy Vertical, horizontal, angular, cylindrical, and geometric

430

NREL: Wind Research - WindPACT  

NLE Websites -- All DOE Office Websites (Extended Search)

WindPACT WindPACT The Wind Partnerships for Advanced Component Technology (WindPACT) studies were conducted to assist industry by testing innovative components, such as advanced blades and drivetrains, to lower the cost of energy. Specific goals included: Foster technological advancements to reduce the cost of wind energy Determine probable size ranges of advanced utility-scale turbines over the next decade for U.S. application Evaluate advanced concepts that are necessary to achieve objectives of cost and size for future turbines Identify and solve technological hurdles that may block industry from taking advantage of promising technology Design, fabricate, and test selected advanced components to prove their viability Support wind industry through transfer of technology from

431

Shallow horizontal drilling in unconsolidated sands offshore California  

SciTech Connect

Four shallow horizontal wells were drilled from Platform C in Dos Cuadras field offshore California to recover reserves inaccessible with conventional drilling techniques. The wells had true vertical depths (TVD's) ranging from 746 to 989 ft with total horizontal displacements from 1,613 to 3,788 ft. The wells had horizontal displacement TVD ratios up to 3.95. The targets were unconsolidated, high-permeability sands. This paper details well planning, drilling, and completion.

Payne, J.D.; Bunyak, M.J. (Unocal Corp., Los Angeles, CA (United States)); Huston, C.W. (Smith International Inc., Tyler, TX (United States))

1993-12-01T23:59:59.000Z

432

Measurements of sky luminance, sky illuminance, and horizontal solar radiation  

Science Conference Proceedings (OSTI)

This paper presents initial findings of a sky measurement program currently in progress at the National Bureau of Standards. Measurements are reported on sky luminance and illuminance and how they relate to horizontal solar radiation and sun position. Correlations are presented relating horizontal illuminance to horizontal solar radiation, and zenith luminance to solar altitude. These empirical models are particularly suitable for use in daylighting energy studies since they are based on existing solar data currently available on standard weather tapes.

Treado, S.; Gillette, G.

1983-04-01T23:59:59.000Z

433

Guided Horizontal Drilling: A Primer for Electric Utilities  

Science Conference Proceedings (OSTI)

This document is intended to be an introduction to guided horizontal drilling, also termed horizontal directional drilling (HDD), as an alternative construction method to open trenching for the installation of underground power cables, pipes, ducts, or conduits. It is written for an audience that includes electric power engineers, designers, operations and procurement personnel. The document introduces guided horizontal drilling technology, the equipment, and several critical aspects of operating the equ...

1997-02-18T23:59:59.000Z

434

Mesoscale Simulations of a Wind Ramping Event for Wind Energy Prediction  

DOE Green Energy (OSTI)

Ramping events, or rapid changes of wind speed and wind direction over a short period of time, present challenges to power grid operators in regions with significant penetrations of wind energy in the power grid portfolio. Improved predictions of wind power availability require adequate predictions of the timing of ramping events. For the ramping event investigated here, the Weather Research and Forecasting (WRF) model was run at three horizontal resolutions in 'mesoscale' mode: 8100m, 2700m, and 900m. Two Planetary Boundary Layer (PBL) schemes, the Yonsei University (YSU) and Mellor-Yamada-Janjic (MYJ) schemes, were run at each resolution as well. Simulations were not 'tuned' with nuanced choices of vertical resolution or tuning parameters so that these simulations may be considered 'out-of-the-box' tests of a numerical weather prediction code. Simulations are compared with sodar observations during a wind ramping event at a 'West Coast North America' wind farm. Despite differences in the boundary-layer schemes, no significant differences were observed in the abilities of the schemes to capture the timing of the ramping event. As collaborators have identified, the boundary conditions of these simulations probably dominate the physics of the simulations. They suggest that future investigations into characterization of ramping events employ ensembles of simulations, and that the ensembles include variations of boundary conditions. Furthermore, the failure of these simulations to capture not only the timing of the ramping event but the shape of the wind profile during the ramping event (regardless of its timing) indicates that the set-up and execution of such simulations for wind power forecasting requires skill and tuning of the simulations for a specific site.

Rhodes, M; Lundquist, J K

2011-09-21T23:59:59.000Z

435

Multi-winding homopolar electric machine  

SciTech Connect

A multi-winding homopolar electric machine and method for converting between mechanical energy and electrical energy. The electric machine includes a shaft defining an axis of rotation, first and second magnets, a shielding portion, and a conductor. First and second magnets are coaxial with the shaft and include a charged pole surface and an oppositely charged pole surface, the charged pole surfaces facing one another to form a repulsive field therebetween. The shield portion extends between the magnets to confine at least a portion of the repulsive field to between the first and second magnets. The conductor extends between first and second end contacts and is toroidally coiled about the first and second magnets and the shield portion to develop a voltage across the first and second end contacts in response to rotation of the electric machine about the axis of rotation.

Van Neste, Charles W

2012-10-16T23:59:59.000Z

436

Wind | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Wind Wind Wind America is home to one of the largest and fastest growing wind markets in the world. Watch the video to learn more about the latest trends in the U.S. wind power market and join us this Thursday, August 8 at 3 pm ET for a Google+ Hangout on wind energy in America. The United States is home to one of the largest and fastest growing wind markets in the world. To stay competitive in this sector, the Energy Department invests in wind projects, both on land and offshore, to advance technology innovations, create job opportunities and boost economic growth. Moving forward, the U.S. wind industry remains a critical part of the Energy Department's all-of-the-above energy strategy to cut carbon pollution, diversify our energy economy and bring the next-generation of

437

2009 Wind Technologies Market Report  

NLE Websites -- All DOE Office Websites (Extended Search)

PROGRAM 2 Presentation Overview * Introduction to 2009 edition of U.S. wind energy market report * Wind installation trends * Wind industry trends * Price, cost, and...

438

2011 Wind Technologies Market Report  

E-Print Network (OSTI)

2010. SPP WITF Wind Integration Study. Little Rock,GE Energy. 2011a. Oahu Wind Integration Study Final Report.Corp. 2010. Eastern Wind Integration and Transmission Study.

Bolinger, Mark

2013-01-01T23:59:59.000Z

439

2009 Wind Technologies Market Report  

E-Print Network (OSTI)

Prepared for the Utility Wind Integration Group. Arlington,Arizona Public Service Wind Integration Cost Impact Study.2010. SPP WITF Wind Integration Study. Little Rock,

Wiser, Ryan

2010-01-01T23:59:59.000Z

440

2010 Wind Technologies Market Report  

E-Print Network (OSTI)

The wind energy integration, transmission, and policy2012, however, federal policy towards wind energy remainsin federal policy towards wind energy after 2012 places such

Wiser, Ryan

2012-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "horizontal axis wind" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

2009 Wind Technologies Market Report  

E-Print Network (OSTI)

The wind energy integration, transmission, and policyPTC. Moreover, federal policy towards wind energy remainsand policy announcements demonstrate accelerated activity in the offshore wind energy

Wiser, Ryan

2010-01-01T23:59:59.000Z

442

2011 Wind Technologies Market Report  

E-Print Network (OSTI)

performance, and price of wind energy, policy uncertainty –The wind energy integration, transmission, and policyand absent supportive policies for wind energy. That said,

Bolinger, Mark

2013-01-01T23:59:59.000Z

443

WIND DATA REPORT Presque Isle  

E-Print Network (OSTI)

WIND DATA REPORT Presque Isle December 1, 2004 ­ December 1, 2005 Prepared for United States ......................................................................................................... 9 Wind Speed Time Series........................................................................................................... 10 Wind Speed Distributions

Massachusetts at Amherst, University of

444

WIND DATA REPORT Thompson Island  

E-Print Network (OSTI)

WIND DATA REPORT Thompson Island June 1, 2003 ­ August 31, 2003 Prepared for Massachusetts...................................................................................................................... 9 Wind Speed Time Series............................................................................................................. 9 Wind Speed Distribution

Massachusetts at Amherst, University of

445

WIND DATA REPORT Thompson Island  

E-Print Network (OSTI)

WIND DATA REPORT Thompson Island December 1, 2003 ­ February 29, 2004 Prepared for Massachusetts.................................................................................................................... 11 Wind Speed Time Series........................................................................................................... 11 Wind Speed Distribution

Massachusetts at Amherst, University of

446

WIND DATA REPORT Thompson Island  

E-Print Network (OSTI)

WIND DATA REPORT Thompson Island June 1, 2004 ­ August 31, 2004 Prepared for Massachusetts...................................................................................................................... 9 Wind Speed Time Series............................................................................................................. 9 Wind Speed Distribution

Massachusetts at Amherst, University of

447

WIND DATA REPORT FALMOUTH, MA  

E-Print Network (OSTI)

WIND DATA REPORT FALMOUTH, MA June1, 2004 to August 31, 2004. Prepared for Massachusetts Technology...................................................................................................................... 8 Wind Speed Time Series............................................................................................................. 8 Wind Speed Distributions

Massachusetts at Amherst, University of

448

WIND DATA REPORT Thompson Island  

E-Print Network (OSTI)

WIND DATA REPORT Thompson Island September 1, 2003 ­ November 30, 2003 Prepared for Massachusetts...................................................................................................................... 9 Wind Speed Time Series............................................................................................................. 9 Wind Speed Distribution

Massachusetts at Amherst, University of

449

WIND DATA REPORT Thompson Island  

E-Print Network (OSTI)

WIND DATA REPORT Thompson Island March 1, 2004 ­ May 31, 2004 Prepared for Massachusetts Technology...................................................................................................................... 9 Wind Speed Time Series............................................................................................................. 9 Wind Speed Distribution

Massachusetts at Amherst, University of

450

WIND DATA REPORT Presque Isle  

E-Print Network (OSTI)

WIND DATA REPORT Presque Isle December 1, 2004 ­ February 28, 2005 Prepared for United States.................................................................................................................... 10 Wind Speed Time Series........................................................................................................... 10 Wind Speed Distributions

Massachusetts at Amherst, University of

451

WIND DATA REPORT Presque Isle  

E-Print Network (OSTI)

WIND DATA REPORT Presque Isle March 1, 2005 ­ May 31, 2005 Prepared for United States Department.................................................................................................................... 10 Wind Speed Time Series........................................................................................................... 10 Wind Speed Distributions

Massachusetts at Amherst, University of

452

WIND DATA REPORT Presque Isle  

E-Print Network (OSTI)

WIND DATA REPORT Presque Isle June 1, 2005 ­ August 31, 2005 Prepared for United States Department...................................................................................................................... 9 Wind Speed Time Series............................................................................................................. 9 Wind Speed Distributions

Massachusetts at Amherst, University of

453

WIND DATA REPORT Thompson Island  

E-Print Network (OSTI)

WIND DATA REPORT Thompson Island March 1, 2003 ­ May 31, 2003 Prepared for Massachusetts Technology...................................................................................................................... 9 Wind Speed Time Series............................................................................................................. 9 Wind Speed Distributions

Massachusetts at Amherst, University of

454

2010 Wind Technologies Market Report  

E-Print Network (OSTI)

turbine prices. Installed project costs are found to exhibitpressure on total project costs and wind power prices. Windinstalled wind power project costs, wind turbine transaction

Wiser, Ryan

2012-01-01T23:59:59.000Z

455

2009 Wind Technologies Market Report  

E-Print Network (OSTI)

downward pressure on project costs and wind power prices.installed wind power project costs, wind turbine transactionand uncertain offshore project costs, and public acceptance

Wiser, Ryan

2010-01-01T23:59:59.000Z

456

2009 Wind Technologies Market Report  

E-Print Network (OSTI)

Prepared for the Utility Wind Integration Group. Arlington,Consult. 2010. International Wind Energy Development: WorldUBS Global I/O: Global Wind Sector. UBS Investment Research.

Wiser, Ryan

2010-01-01T23:59:59.000Z

457

2008 WIND TECHNOLOGIES MARKET REPORT  

E-Print Network (OSTI)

2008. Washington, DC: American Wind Energy Association.American Wind Energy Association ( AWEA).2009b. AWEA Small Wind Turbine Global Market Study: Year

Bolinger, Mark

2010-01-01T23:59:59.000Z

458

2010 Wind Technologies Market Report  

E-Print Network (OSTI)

and Minnesota (12%). Offshore Wind Power Project and Policythe emergence of an offshore wind power market still facesexists in developing offshore wind energy in several parts

Wiser, Ryan

2012-01-01T23:59:59.000Z

459

2008 WIND TECHNOLOGIES MARKET REPORT  

E-Print Network (OSTI)

11 “advanced-stage” offshore wind project proposals totalingcontinued in 2008 (see Offshore Wind Development Activities,Market Report Offshore Wind Development Activities In

Bolinger, Mark

2010-01-01T23:59:59.000Z

460

2011 Wind Technologies Market Report  

E-Print Network (OSTI)

natural gas prices), pushed wind energy to the top of (andperformance, and price of wind energy, policy uncertainty –cost, performance, and price of wind energy, some of these

Bolinger, Mark

2013-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "horizontal axis wind" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

RI_50m_Wind  

NLE Websites -- All DOE Office Websites (Extended Search)

UnitedStatesWindHighResolutionRhodeIslandWindHighResolution.zip> Description: Abstract: Annual average wind resource potential for the state of Rhode...

462

CT_50m_Wind  

NLE Websites -- All DOE Office Websites (Extended Search)

UnitedStatesWindHighResolutionConnecticutWindHighResolution.zip> Description: Abstract: Annual average wind resource potential for the state of...

463

MA_50m_Wind  

NLE Websites -- All DOE Office Websites (Extended Search)

UnitedStatesWindHighResolutionMassachusettsWindHighResolution.zip> Description: Abstract: Annual average wind resource potential for the state of...

464

VT_50m_Wind  

NLE Websites -- All DOE Office Websites (Extended Search)

DataTechnologySpecificUnitedStatesWindHighResolutionVermontWindHighResolution.zip> Description: Abstract: Annual average wind resource potential for the state of Vermont...

465

NH_50m_Wind  

NLE Websites -- All DOE Office Websites (Extended Search)

UnitedStatesWindHighResolutionNewHampshireWindHighResolution.zip> Description: Abstract: Annual average wind resource potential for the state of New...

466

IA_50m_Wind  

NLE Websites -- All DOE Office Websites (Extended Search)

ISDataTechnologySpecificUnitedStatesWindHighResolutionIowaWindHighResolution.zip> Description: Abstract: Annual average wind resource potential for the state of Iowa at...

467

ME_50m_Wind  

NLE Websites -- All DOE Office Websites (Extended Search)

SDataTechnologySpecificUnitedStatesWindHighResolutionMaineWindHighResolution.zip> Description: Abstract: Annual average wind resource potential for the state of Maine...

468

ga_50m_wind  

NLE Websites -- All DOE Office Websites (Extended Search)

DataTechnologySpecificUnitedStatesWindHighResolutionGeorgiaWindHighResolution.zip> Description: Abstract: Annual average wind resource potential for the state of Georgia...

469

ny_50m_wind  

NLE Websites -- All DOE Office Websites (Extended Search)

ataTechnologySpecificUnitedStatesWindHighResolutionNewYorkWindHighResolution.zip> Description: Abstract: Annual average wind resource potential for New York at a 50...

470

2010 Wind Technologies Market Report  

E-Print Network (OSTI)

federal and state incentives for wind energy deployment. Thefederal and state incentives for wind energy deployment.federal and state incentives for wind energy deployment in

Wiser, Ryan

2012-01-01T23:59:59.000Z

471

2011 Wind Technologies Market Report  

E-Print Network (OSTI)

continued state and federal incentives for wind energy,continued state and federal incentives for wind energy,continued state and federal incentives for wind energy,

Bolinger, Mark

2013-01-01T23:59:59.000Z

472

2008 WIND TECHNOLOGIES MARKET REPORT  

E-Print Network (OSTI)

2008. Washington, DC: American Wind Energy Association.American Wind Energy Association ( AWEA). 2009b. AWEA SmallWashington, DC: American Wind Energy Association. Bolinger,

Bolinger, Mark

2010-01-01T23:59:59.000Z

473

2009 Wind Technologies Market Report  

E-Print Network (OSTI)

2010. International Wind Energy Development: World MarketUniversity. American Wind Energy Association (AWEA). 2010a.Washington, DC: American Wind Energy Association. American

Wiser, Ryan

2010-01-01T23:59:59.000Z

474

2009 Wind Technologies Market Report  

E-Print Network (OSTI)

2010. Status of Centralized Wind Power Forecasting in NorthInterconnection Policies and Wind Power: A Discussion ofs first utility-scale wind power project. Credit: Klaus

Wiser, Ryan

2010-01-01T23:59:59.000Z

475

2008 WIND TECHNOLOGIES MARKET REPORT  

E-Print Network (OSTI)

The Effects of Integrating Wind Power on Transmission SystemInterconnection Policies and Wind Power: A Discussion ofof their database of wind power projects, and for providing

Bolinger, Mark

2010-01-01T23:59:59.000Z

476

DOE Science Showcase - Wind Power  

Office of Scientific and Technical Information (OSTI)

Power Testing and Data in General Wind and Turbine Dynamics Wind Stresses Control, the Power Grid, and the Grids Economics Environmental Effects Energy101: Wind Turbines...

477

Spin-stabilized magnetic levitation without vertical axis of rotation  

DOE Patents (OSTI)

The symmetry properties of a magnetic levitation arrangement are exploited to produce spin-stabilized magnetic levitation without aligning the rotational axis of the rotor with the direction of the force of gravity. The rotation of the rotor stabilizes perturbations directed parallel to the rotational axis.

Romero, Louis (Albuquerque, NM); Christenson, Todd (Albuquerque, NM); Aaronson, Gene (Albuquerque, NM)

2009-06-09T23:59:59.000Z

478

Drilling Sideways -- A Review of Horizontal Well Technology and ...  

U.S. Energy Information Administration (EIA)

DOE/EIA-TR-0565 Distribution Category UC-950 Drilling Sideways -- A Review of Horizontal Well Technology and Its Domestic Application April 1993 Energy Information ...

479

NREL: Wind Research - Projects  

NLE Websites -- All DOE Office Websites (Extended Search)

Projects Projects NREL's wind energy research and development projects focus on reducing the cost of wind technology and expanding access to wind energy sites. Our specialized technical expertise, comprehensive design and analysis tools, and unique testing facilities help industry overcome challenges to bringing new wind technology to the marketplace. Some of these success stories are described in NREL's Wind R&D Success Stories. We also work closely with universities and other national laboratories supporting fundamental research in wind technologies, including aerodynamics, aeroacoustics, and material sciences essential in the development of new blade technologies and advanced controls, power electronics, and testing to further refine drivetrain topology.

480

Wind Power Career Chat  

DOE Green Energy (OSTI)

This document will teach students about careers in the wind energy industry. Wind energy, both land-based and offshore, is expected to provide thousands of new jobs in the next several decades. Wind energy companies are growing rapidly to meet America's demand for clean, renewable, and domestic energy. These companies need skilled professionals. Wind power careers will require educated people from a variety of areas. Trained and qualified workers manufacture, construct, operate, and manage wind energy facilities. The nation will also need skilled researchers, scientists, and engineers to plan and develop the next generation of wind energy technologies.

Not Available

2011-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "horizontal axis wind" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Wind power today  

DOE Green Energy (OSTI)

This publication highlights initiatives of the US DOE`s Wind Energy Program. 1997 yearly activities are also very briefly summarized. The first article describes a 6-megawatt wind power plant installed in Vermont. Another article summarizes technical advances in wind turbine technology, and describes next-generation utility and small wind turbines in the planning stages. A village power project in Alaska using three 50-kilowatt turbines is described. Very brief summaries of the Federal Wind Energy Program and the National Wind Technology Center are also included in the publication.

NONE

1998-04-01T23:59:59.000Z

482

Wind energy information guide  

DOE Green Energy (OSTI)

This book is divided into nine chapters. Chapters 1--8 provide background and annotated references on wind energy research, development, and commercialization. Chapter 9 lists additional sources of printed information and relevant organizations. Four indices provide alphabetical access to authors, organizations, computer models and design tools, and subjects. A list of abbreviations and acronyms is also included. Chapter topics include: introduction; economics of using wind energy; wind energy resources; wind turbine design, development, and testing; applications; environmental issues of wind power; institutional issues; and wind energy systems development.

NONE

1996-04-01T23:59:59.000Z

483

The WEI6K, a 6-kW 7-m Small Wind Turbine: Final Technical Report  

SciTech Connect

This project was selected by the U.S. Department of Energy under a DOE solicitation “Low Wind Speed Technology for Small Turbine Development.” The objective of this project has been to design a new small wind turbine with improved cost, reliability and performance in grid-connected residential and small business applications, in order to achieve the overall DOE goal of cost effectiveness in Class 3 wind resources that can now be achieved in Class 5 resources. The scope of work for this project has been to complete the preliminary design of an improved small wind turbine, including preliminary loads and strength analyses; analysis and design of all major components; systems integration and structural dynamic analysis; estimation of life-cycle cost of energy; and design documentation and review. The project did not entail hardware fabrication or testing. The WEI6K Turbine resulting from this project is an upwind horizontal-axis wind turbine rated at 6 kW. It features a 3-blade 7-m diameter rotor. The generator is a direct-drive permanent magnet synchronous machine generating 3-phase power at 240 VAC. The turbine is maintained oriented in to the wind via active yaw control using electromechanical servos. Power is regulated with active blade pitch control. The turbine is presently designed to be placed on a 100-foot (30m) tower. The turbine is predicted to generate electricity at a levelized cost of energy (COE) between 7.3 and 8.9 ¢/kWh at an IEC Class II site, with an average wind speed of 8.5 m/s at hub height, depending upon whether the customer uses a guyed truss tower (the lower figure) or a monopole tower. For the NREL Reference Site, with a mean wind speed of 5.35 m/s at 10 m height, the turbine would generate at a levelized cost of energy of between 9.7 and 11.9 ¢/kWh. The lowest of these numbers is presently competitive with retail electricity rates in most of the country. The 8.9 ¢/kWh is still competitive with retail rates in many regions of the country with high electricity costs. The study further concludes that several design changes could shave 10-14% from the cost of energy determined in the preliminary design. These changes include a new tower design that offers tilt-up capability without guy wires and takes better advantage of the lowered loads produced by pitch control; design a family of airfoils more appropriate for pitch regulation on a turbine of this size; tune the pitch controller properly to minimize shedding of power during turbulent operation in the transition from Region 2 to 3; value engineer the pitch system to shave costs, including consideration of a collective pitch system; and refine the design of the hub and main frame castings to minimize weight and cost. We are generally encouraged by the results. These preliminary numbers show that we can produce a turbine that is competitive with retail electric rates at relatively windy IEC Class II sites. With further improvements in the design, we believe the turbine could be competitive at sites with lesser wind resource.

Wetzel, Kyle K.; McCleer, Patrick J.; Hahlbeck, Edwin C.; DOE Project Office - Keith Bennett

2006-07-21T23:59:59.000Z

484

Validation of regional wind resource predictions in the Northern Great Plains  

DOE Green Energy (OSTI)

The development and validation of computerized wind mapping tools for regional assessment purposes is an important step in accelerating wind energy deployment. This paper summarizes the results of a validation study of the automated wind resource mapping technique developed at the National Renewable Energy Laboratory (NREL). This technique uses Geographic Information System (GIS) software and produces high horizontal resolution (1 km) wind resource maps. The automated wind maps have been used to help plan wind measurement programs and to define potential areas for wind energy projects in countries such as Mexico, Chile, Indonesia, and China. The authors chose a US location for this project to test the accuracy of the automated mapping technique in a region where the wind resource distribution was already fairly well known. The Buffalo Ridge region of the Northern Great Plains served as the subject area. The study area covered northwestern Iowa, southwestern Minnesota, and adjacent parts of South Dakota and Nebraska. This area had several advantages for use in a validation study. First, this area has active wind energy development and the results would be of interest to the wind energy community. Second, a validation data set would be fairly easy to derive because recent wind measurements were taken in that region specifically for wind energy purposes. These data were publicly available and easily obtained. Finally, the relatively simple terrain in that region enabled this study to be completed in a timely manner.

Elliott, D.; Schwartz, M.

1998-08-01T23:59:59.000Z

485

NREL: Education Programs - KidWind Project and Wind Education...  

NLE Websites -- All DOE Office Websites (Extended Search)

KidWind Project and Wind Education in the Classroom: Wind Powering America Lessons Learned July 1, 2013 Integrating wind energy curricula into the classroom can seem like a...

486

NREL: Wind Research - Landing a Job in the Wind Industry: Wind...  

NLE Websites -- All DOE Office Websites (Extended Search)

Landing a Job in the Wind Industry: Wind Powering America Lessons Learned January 28, 2013 Wind Powering America interviewed Marilla Lamb, a 2012 graduate of Northern Arizona...

487

Method and application of horizontal slice volumetrics to waterflood management and horizontal drilling  

SciTech Connect

A computer mapping program was used to make horizontal slices of pore volume. The goal was to create maps that showed the distribution of pore volume vertically and laterally throughout the reservoir. That information was used for studying waterflood feasibility, monitoring an existing waterflood, and planning a horizontal well. This work was done at the United States Naval Petroleum Reserve No. 1, Elk Hills, CA. The reservoirs are the Miocene aged Northwest Stevens A sands and T N sands. These sands are a series of stacked deep water turbidites draped across the western nose of a plunging anticline. To determine the reservoir sensitivity to the approach used to calculate horizontal slice volume, two methods were tested. The first involves creation of four isochores, bounded above by the sand top or base and below by the slice top or base, whose volumes are combined to give the slice volume. The second involves creation of a grid of the slice itself from which slice volume is calculated.

Deshpande, A.; Flemings, P.B. (Pennsylvania State Univ., University Park, PA (United States)); Huang, J. (Exxon Production Research Co., Houston, TX (United States))

1996-01-01T23:59:59.000Z

488

Demonstration of a utility industry horizontal drilling system: Horizontal well AMH-5 installation report  

SciTech Connect

The Department of Energy`s Office of Technology Development initiated an integrated demonstration of innovative technologies and systems for cleanup of VOCs in soils and groundwater at the Savannah River Site (SRS) in 1989. The overall goal of the program is demonstration of multiple technologies and systems in the fields of drilling, characterization, monitoring, and remediation at a single test bed. Innovative technologies are compared to one another and to baseline technologies in terms of technical performance and cost effectiveness. Transfer of successfully demonstrated technologies and systems to DOE environmental restoration organizations, to other government agencies, and to industry is a critical part of the program. Directional drilling has been shown to be a successful technique for enhancing access to the subsurface, thus improving remediation systems, especially remediation systems which perform in situ. Demonstration of an innovative directional drilling system at the Integrated Demonstration Site at the SRS, was initiated in June of 1992. The directional drilling system was designed to install an in situ remediation system. The drilling system is an experimental compaction/dry drilling technique developed by Charles Machine Works (Ditch Witch{reg_sign}) of Perry, Oklahoma. A horizontal well was installed in the M Area of the SRS below and parallel to an abandoned tile process sewer line. The installation of the horizontal well was a two-part process. Part one consisted of drilling the borehole, and part two was the horizontal well completion.

Not Available

1992-12-31T23:59:59.000Z

489

Jet spoiler arrangement for wind turbine  

DOE Patents (OSTI)

An air jet spoiler arrangement is provided for a Darrieus-type vertical axis wind-powered turbine. Air is drawn into hollow turbine blades through air inlets at the ends thereof and is ejected in the form of air jets through small holes or openings provided along the lengths of the blades. The air jets create flow separation at the surfaces of the turbine blades, thereby inducing stall conditions and reducing the output power. A feedback control unit senses the power output of the turbine and controls the amount of air drawn into the air inlets accordingly.

Cyrus, Jack D. (Corrales, NM); Kadlec, Emil G. (Albuquerque, NM); Klimas, Paul C. (Albuquerque, NM)

1985-01-01T23:59:59.000Z

490

Jet spoiler arrangement for wind turbine  

DOE Patents (OSTI)

An air jet spoiler arrangement is provided for a Darrieus-type vertical axis wind-powered turbine. Air is drawn into hollow turbine blades through air inlets at the end thereof and is ejected in the form of air jets through small holes or openings provided along the lengths of the blades. The air jets create flow separation at the surfaces of the turbine blades, thereby including stall conditions and reducing the output power. A feedback control unit senses the power output of the turbine and controls the amount of air drawn into the air inlets accordingly.

Cyrus, J.D.; Kadlec, E.G.; Klimas, P.C.

1983-09-15T23:59:59.000Z

491

2008 Wind Energy Projects, Wind Powering America (Poster)  

SciTech Connect

The Wind Powering America program produces a poster at the end of every calendar year that depicts new U.S. wind energy projects. The 2008 poster includes the following projects: Stetson Wind Farm in Maine; Dutch Hill Wind Farm in New York; Grand Ridge Wind Energy Center in Illinois; Hooper Bay, Alaska; Forestburg, South Dakota; Elbow Creek Wind Project in Texas; Glacier Wind Farm in Montana; Wray, Colorado; Smoky Hills Wind Farm in Kansas; Forbes Park Wind Project in Massachusetts; Spanish Fork, Utah; Goodland Wind Farm in Indiana; and the Tatanka Wind Energy Project on the border of North Dakota and South Dakota.

2009-01-01T23:59:59.000Z

492

Passive load control for large wind turbines.  

DOE Green Energy (OSTI)

Wind energy research activities at Sandia National Laboratories focus on developing large rotors that are lighter and more cost-effective than those designed with current technologies. Because gravity scales as the cube of the blade length, gravity loads become a constraining design factor for very large blades. Efforts to passively reduce turbulent loading has shown significant potential to reduce blade weight and capture more energy. Research in passive load reduction for wind turbines began at Sandia in the late 1990's and has moved from analytical studies to blade applications. This paper discusses the test results of two Sandia prototype research blades that incorporate load reduction techniques. The TX-100 is a 9-m long blade that induces bend-twist coupling with the use of off-axis carbon in the skin. The STAR blade is a 27-m long blade that induces bend-twist coupling by sweeping the blade in a geometric fashion.

Ashwill, Thomas D.

2010-05-01T23:59:59.000Z

493

Virtual Wind Speed Sensor for Wind Turbines Andrew Kusiak1  

E-Print Network (OSTI)

Virtual Wind Speed Sensor for Wind Turbines Andrew Kusiak1 ; Haiyang Zheng2 ; and Zijun Zhang3 Abstract: A data-driven approach for development of a virtual wind-speed sensor for wind turbines is presented. The virtual wind-speed sensor is built from historical wind-farm data by data-mining algorithms

Kusiak, Andrew

494

2008 WIND TECHNOLOGIES MARKET REPORT  

E-Print Network (OSTI)

Prepared for the Utility Wind Integration Group. Arlington,Wind Logics, Inc. 2004. Wind Integration Study—Final Report.EnerNex Corp. 2006. Wind Integration Study for Public

Bolinger, Mark

2010-01-01T23:59:59.000Z

495

Energy Basics: Wind Power Animation  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

EERE: Energy Basics Wind Power Animation This animation discusses the advantages of wind power, the workings of a wind turbine, and wind resources in the United States. It also...

496

Wind Blog | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Wind Blog Wind Blog RSS September 26, 2013 Wind Farm Brings Clean, Affordable Energy to Alaskan Cooperative How can we make it easier for more communities to use wind power?...

497

2010 Wind Technologies Market Report  

E-Print Network (OSTI)

growth in U.S. wind turbine manufacturing capability and the drop in wind power plantgrowth in U.S. wind turbine manufacturing capability and the drop in wind power plant

Wiser, Ryan

2012-01-01T23:59:59.000Z

498

Severe Convective Wind Environments  

Science Conference Proceedings (OSTI)

Nontornadic thunderstorm winds from long-lived, widespread convective windstorms can have a tremendous impact on human lives and property. To examine environments that support damaging wind producing convection, sounding parameters from Rapid ...

Evan L. Kuchera; Matthew D. Parker

2006-08-01T23:59:59.000Z

499

Greensburg Wind Farm  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

renewable energy and energy efficiency. * Kansas offers the third highest potential for wind energy in the U.S. * Thorough research conducted by NREL proved the viability of wind...

500

Wind Rose Bias Correction  

Science Conference Proceedings (OSTI)

Wind rose summaries, which provide a basis for understanding and evaluating the climatological behavior of local wind, have a directional bias if a conventional method is used in their generation. Three techniques used to remove this bias are ...

Scott Applequist

2012-07-01T23:59:59.000Z