Powered by Deep Web Technologies
Note: This page contains sample records for the topic "high-voltage direct current" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

A High Voltage Direct Current Generator  

Science Journals Connector (OSTI)

When powdered materials are blown through metal tubes by means of compressed air considerable quantities of electricity are produced by contact electrification. It was found that 6×10-5 coulombs could be produced per gram of diatomaceous earth, a form of silica, blown through a short length of copper tube. A generator of extremely high voltage is proposed, and a small scale model of such a generator is described, by means of which currents of 8×10-5 amperes at 260 kilovolts were generated.

Richard E. Vollrath

1932-10-15T23:59:59.000Z

2

Summary of multiterminal high-voltage direct current transmission technology  

SciTech Connect (OSTI)

This report summarizes the present state of multiterminal (MT) high-voltage direct current (HVDC) power transmission. The purpose is to reassess the need for HVDC circuit breakers and to identify needed research for MT HVDC. The fundamentals of this technology are presented, and previous research and development is reviewed. Although no MT HVDC systems have yet been built, many concepts have been proposed. Some require a dc breaker, and others do not. Both options have advantages and disadvantages for various applications, so the selection will depend on the proposed application. Research is needed to define operating characteristics of various MT HVDC systems. In some applications, dc breakers will be useful, so research into HVDC interruption should continue. Also, dc fault detection and control algorithms for MT systems should be studied.

Biggs, R.B.; Jewell, W.T.

1984-05-01T23:59:59.000Z

3

An Annotated Bibliography of High-Voltage Direct-Current Transmission and Flexible AC Transmission (FACTS) Devices, 1991-1993.  

SciTech Connect (OSTI)

References are contained for HVDC systems, converter stations and components, overhead transmission lines, cable transmission, system design and operations, simulation of high voltage direct current systems, high-voltage direct current installations, and flexible AC transmission system (FACTS).

Litzenberger, Wayne; Lava, Val

1994-08-01T23:59:59.000Z

4

Partial discharge measurements on a high voltage direct current mass impregnated paper cable  

SciTech Connect (OSTI)

Partial discharge measurement has been a good tool for the quality assurance of cables under alternating voltage. With the growing interest in High Voltage Direct Current cables it seems therefore logical to extend this technique for use at direct voltage. The paper describes this technique as used on a HVDC cable with mass impregnated paper. The different phases of operation (no load, full load, cooling phase, etc.) are characterized by a different discharge behavior. Special attention is given to the dangerous cooling phase. Models have been developed which can explain the discharge patterns that were measured. This paper gives an insight in the electrical behavior of a HVDC cable with mass impregnated paper insulation.

Jeroense, M.J.P. [NKF KABEL B.V., Delft (Netherlands); Kreuger, F.H. [Delft Univ. of Technology (Netherlands)

1996-12-31T23:59:59.000Z

5

Recommended practice for fire protection for electric generating plants and high voltage direct current converter stations. 2005 ed.  

SciTech Connect (OSTI)

The standard outlines fire safety recommendations for gas, oil, coal, and alternative fuel electric generating plants including high voltage direct current converter stations and combustion turbine units greater than 7500 hp used for electric generation. Provisions apply to both new and existing plants. The document provides fire prevention and fire protection recommendations for the: safety of construction and operating personnel; physical integrity of plant components; and continuity of plant operations. The 2005 edition includes revisions and new art that clarify existing provisions. 5 annexes.

NONE

2005-07-01T23:59:59.000Z

6

Epidemiologic study of Holstein dairy cow performance and reproduction near a high-voltage direct - current powerline  

SciTech Connect (OSTI)

The development and operation of a high-voltage direct-current (HVDC) transmission line in rural Minnesota generated public concern over potential adverse effects to nearby residents and their livestock. Electrical parameters near an HVDC line decline rapidly with distance, but effects on ambient space charge have been detected out to 1 mile. To identify potential adverse effects of HVDC line operation on livestock, case-control and cohort study methods were used to examine various indices of Holstein performance in relation to distance from the line and the onset of line operation. It was believed that these indices would reflect changes in physiologic function or overt health effects that might arise from the HVDC environment. High-quality performance data from existing Dairy Herd Improvement Association (DHIA) records were obtained for 97% of qualifying herds located within 10 miles of the line. The large number of animals and years of observation provided high statistical power to detect even small systematic changes in performance. No significant differences in milk production or reproductive capacity were associated with presumed exposure to the HVDC environment. The absence of measurable effects in a large sentinel animal population may have implications for the assessment of human health risks related to HVDC transmission lines.

Martin, F.B.; Bender, A.; Steuernagel, G.; Robinson, R.A.; Revsbech, R.; Sorensen, D.K.; Williamson, N.; Williams, A.

1986-01-01T23:59:59.000Z

7

A 4000-A HVDC (high-voltage direct-current) circuit breaker with fast fault-clearing capability: Final report  

SciTech Connect (OSTI)

This project is a follow-up of the first development of a 500 kV HVDC airblast circuit breaker (EPRI project 1507-3). The objective was to increase the current interrupting capability from 2200 A to 4000 A and shorten its fault clearing time. A high current 500 kV HVDC circuit breaker has been built using the passive commutation circuit. The breaker is modular in construction and can be designed for a wide variety of system conditions. More than 400 current interruptions were carried out successfully. Tests have shown that this circuit breaker is capable of interrupting more than 4000 A dc. Practical breakers with current interrupting capability of even 5500 A dc could be built. The circuit breaker operation and the fault-clearing process can be materially speeded up if the trip signal is given as soon as the fault is detected and without waiting for the current levels to come down in response to converter control action. The new dc breakers are shown to be capable of withstanding these transient arc currents of 8000 A without affecting its ability to interrupt the direct current that follows the transient. This transient current withstand capability is greater than is likely to occur during dc faults. The fault clearing time of this HVDC circuit breaker is comparable to the fault clearing time of conventional ac breakers for ac faults. The developed HVDC circuit breaker is now commercially available and can be supplied for use in HVDC systems. Its use in such systems is expected to provide flexibility in system design and contribute to system stability. 38 refs., 52 figs., 9 tabs.

Not Available

1988-04-01T23:59:59.000Z

8

Fiber optic current monitor for high-voltage applications  

DOE Patents [OSTI]

A current monitor which derives its power from the conductor being measured for bidirectionally measuring the magnitude of current (from DC to above 50 khz) flowing through a conductor across which a relatively high level DC voltage is applied, includes a pair of identical transmitter modules connected in opposite polarity to one another in series with the conductor being monitored, for producing from one module a first light signal having an intensity directly proportional to the magnitude of current flowing in one direction through the conductor during one period of time, and from the other module a second light signal having an intensity directly proportional to the magnitude of current flowing in the opposite direction through the conductor during another period of time, and a receiver located in a safe area remote from the high voltage area for receiving the first and second light signals, and converting the same to first and second voltage signals having levels indicative of the magnitude of current being measured at a given time.

Renda, George F. (Plainsboro, NJ)

1992-01-01T23:59:59.000Z

9

Current isolating epitaxial buffer layers for high voltage photodiode array  

DOE Patents [OSTI]

An array of photodiodes in series on a common semi-insulating substrate has a non-conductive buffer layer between the photodiodes and the semi-insulating substrate. The buffer layer reduces current injection leakage between the photodiodes of the array and allows optical energy to be converted to high voltage electrical energy.

Morse, Jeffrey D. (Martinez, CA); Cooper, Gregory A. (Pleasant Hill, CA)

2002-01-01T23:59:59.000Z

10

Geomagnetically induced currents in the Uruguayan high-voltage power grid  

Science Journals Connector (OSTI)

......currents in the Uruguayan high-voltage power grid R. Caraballo 1 2 L. Sanchez Bettucci...simple topology of the Uruguayan power grid provides some advantages in the calculation...transformers at the South African power grid during the Halloween storm in 2003......

R. Caraballo; L. Sánchez Bettucci; G. Tancredi

2013-01-01T23:59:59.000Z

11

The high voltage problem in the saturated core HTS fault current limiter  

Science Journals Connector (OSTI)

A small model of a one-phase saturated core HTS fault current limiter was developed. It consists of an iron core, an AC coil and a DC HTS coil. The HTS coil comprised six 126 turns double-pancakes (ID 70 mm), wound after heat treatment from Bi-2223 multifilamentary tape in Ag matrix. A fault simulation circuit was set up to characterize the dynamic properties of the model limiter. The voltages and currents of the AC coil and the DC HTS coil were measured through a computer-based data acquisition system. The tests have shown that the limiter has a fast response and the first current peak can be easily limited, but a high voltage will be induced on the DC HTS coil side during the fault state. This high voltage can badly affect the DC current equipment on the DC HTS coil side. The origin and value of the high voltage can be explained using a transformer model. For a limiter with n1 turns AC coil and n2 turns DC coil, the largest induced voltage will be roughly close to (n2/n1)U, where U is the rated voltage of the limiter. To commercialize this kind of limiter, the high voltage problem must be solved. Some different designs were introduced to lower the induced voltage.

Y.F. He; J.H. Li; X.H. Zong; J. Sun; Y.N. Wang; C.L. Wu; J.X. Wang

2003-01-01T23:59:59.000Z

12

3D MHD modelling of the glidarc behaviour of a low current high voltage DC plasma torch Journal of Physics D: Applied Physics  

E-Print Network [OSTI]

in terms of: global behaviour, arc length, mean voltage and glidarc frequency. 1. Introduction The non-thermal on magnetohydrodynamic (MHD) modelling of atmospheric pressure direct current (DC) plasma torch operating at low current3D MHD modelling of the glidarc behaviour of a low current ­ high voltage DC plasma torch Journal

Paris-Sud XI, Université de

13

High-voltage direct current handbook: First edition  

SciTech Connect (OSTI)

HVDC systems offer opportunities for power transfer between asynchronous systems, improved performance of the ac system in which the dc link is integrated, and possibly increased power transfer across existing lines if converted to HVDC. This handbook is intended to help planners and engineers understand the intricacies of HVDC systems.

Piwko, R.J.; Leonard, D.J.; Nolan, J.J.; Thorpe, J.B. [eds.] [GE Industrial and Power Systems, Schenectady, NY (United States)

1994-12-31T23:59:59.000Z

14

Connecting Renewables Directly to the Grid: Resilient Multi-Terminal HVDC Networks with High-Voltage High-Frequency Electronics  

SciTech Connect (OSTI)

GENI Project: GE is developing electricity transmission hardware that could connect distributed renewable energy sources, like wind farms, directly to the grid—eliminating the need to feed the energy generated through intermediate power conversion stations before they enter the grid. GE is using the advanced semiconductor material silicon carbide (SiC) to conduct electricity through its transmission hardware because SiC can operate at higher voltage levels than semiconductors made out of other materials. This high-voltage capability is important because electricity must be converted to high-voltage levels before it can be sent along the grid’s network of transmission lines. Power companies do this because less electricity is lost along the lines when the voltage is high.

None

2012-01-23T23:59:59.000Z

15

Geomagnetically induced currents in the Uruguayan high-voltage power grid  

Science Journals Connector (OSTI)

......magnetic field due to an elementary ionospheric current...calculation. Let M elementary currents I, be placed...Earth's surface due to an elementary unit amplitude current...The horizontal electric field at the surface...earthed nodes linked by resistances R ij (i, j......

R. Caraballo; L. Sánchez Bettucci; G. Tancredi

2013-01-01T23:59:59.000Z

16

ABBGroup-1-High voltage lab  

E-Print Network [OSTI]

;©ABBGroup-3- 3-Sep-07 Where does one use circuit breakers? High voltage (HV) circuit breakers are keyA DISTRIBUTION MEDIUM AND LOW VOLTAGE HV circuit breakers #12;©ABBGroup-4- 3-Sep-07 When a breaker fails to interrupt the current... Fault arc at a disconnector Fault arc in a substation #12;©ABBGroup-5- 3-Sep-07

Basse, Nils Plesner

17

Hybrid high direct current circuit interrupter  

DOE Patents [OSTI]

A device and a method are disclosed for interrupting very high direct currents (greater than 100,000 amperes) and simultaneously blocking high voltages (greater than 600 volts). The device utilizes a mechanical switch to carry very high currents continuously with low loss and a silicon controlled rectifier (SCR) to bypass the current around the mechanical switch while its contacts are separating. A commutation circuit, connected in parallel with the SCR, turns off the SCR by utilizing a resonant circuit to divert the SCR current after the switch opens. 7 figs.

Rockot, J.H.; Mikesell, H.E.; Jha, K.N.

1998-08-11T23:59:59.000Z

18

Hybrid high direct current circuit interrupter  

DOE Patents [OSTI]

A device and a method for interrupting very high direct currents (greater than 100,000 amperes) and simultaneously blocking high voltages (greater than 600 volts). The device utilizes a mechanical switch to carry very high currents continuously with low loss and a silicon controlled rectifier (SCR) to bypass the current around the mechanical switch while its contacts are separating. A commutation circuit, connected in parallel with the SCR, turns off the SCR by utilizing a resonant circuit to divert the SCR current after the switch opens.

Rockot, Joseph H. (N. Huntingdon, PA); Mikesell, Harvey E. (McMurray, PA); Jha, Kamal N. (Bethel Park, PA)

1998-01-01T23:59:59.000Z

19

Control of Analyte Electrolysis in Electrospray Ionization Mass Spectrometry Using Repetitively Pulsed High Voltage  

SciTech Connect (OSTI)

Analyte electrolysis using a repetitively pulsed high voltage ion source was investigated and compared to that using a regular, continuously operating direct current high voltage ion source in electrospray ionization mass spectrometry. The extent of analyte electrolysis was explored as a function of the length and frequency of the high voltage pulse using the model compound reserpine in positive ion mode. Using +5 kV as the maximum high voltage amplitude, reserpine was oxidized to its 2, 4, 6 and 8-electron oxidation products when direct current high voltage was employed. In contrast, when using a pulsed high voltage, oxidation of reserpine was eliminated by employing the appropriate high voltage pulse length and frequency. This effect was caused by inefficient mass transport of the analyte to the electrode surface during the duration of the high voltage pulse and the subsequent relaxation of the emitter electrode/ electrolyte interface during the time period when the high voltage was turned off. This mode of ESI source operation allows for analyte electrolysis to be quickly and simply switched on or off electronically via a change in voltage pulse variables.

Kertesz, Vilmos [ORNL; Van Berkel, Gary J [ORNL

2011-01-01T23:59:59.000Z

20

High-voltage engineering  

E-Print Network [OSTI]

High-voltage engineering covers the application, the useful use and proper working of high voltages and high fields. Here we give some introductory examples, i.e., ‘septa’ and ‘kicker’ at the Large Hadron Collider (14 TeV), the Super Proton Synchrotron (450 GeV) and the Proton Synchrotron (26 GeV) accelerators as found at the European Orginization for Nuclear Research (CERN) today. We briefly cover the theoretical foundation (Maxwell equations) and aspects of numerical field simulation methods. Concepts relating to electrical fields, insulation geometry and medium and breakdown are introduced. We discuss ways of generating high voltages with examples of AC sources (50/60 Hz), DC sources, and pulse sources. Insulation and breakdown in gases, liquids, solids and vacuum are presented, including Paschen’s law (breakdown field and streamer breakdown). Applications of the above are discussed, in particular the general application of a transformer. We briefly discuss measurement techniques of partial disch...

Gaxiola, E

2006-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "high-voltage direct current" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Voltage-dependent calcium channels and currents in native neurons and other cells have been divided into high voltage  

E-Print Network [OSTI]

Voltage-dependent calcium channels and currents in native neurons and other cells have been divided than one subtype of channel. A new subfamily of voltage-dependent calcium channel á1 subunit genes. 1999), having four domains, each with a voltage sensor and a pore-forming P loop. However

Dolphin, Annette C.

22

Distributed Voltage and Current Control of Multi-Terminal High-Voltage Direct  

E-Print Network [OSTI]

to AC transmission systems. Off-shore wind farms also typically require HVDC power transmission This work was supported in part by the European Commission by the Hycon2 project, the Swedish Research

Dimarogonas, Dimos

23

Identification of ions near HVDC (high-voltage direct-current) transmission lines: Final report  

SciTech Connect (OSTI)

Positive and negative ion species were identified and studied at two separate field sites and one laboratory site. The first field study was conducted under an operating HVDC transmission line. The second was near a HVDC test line and measurements were performed with the line in both an energized and de-energized state. During clear, sunny days HSO/sub 4//sup /minus///center dot/H/sub 2/SO/sub 4/ was observed to be the dominant negative ion in the natural ion spectrum. At night, however, HSO/sub 4//sup /minus// core ions virtually disappeared, and were replaced by NO/sub 3//sup /minus// core ions and their first nitric acid cluster. Both negative spectra also typically contained lesser concentrations of the malonate ion. The transmission line negative spectra were similar but were typically dominated by the NO/sub 3//sup /minus// core ions during both day and night. The positive ions observed under HVDC lines were typically either NH/sub 4//sup +/ or C/sub 5/H/sub 6/N/sup +/, which reacted with higher proton affinity species (such as methylpyridines, trimethylamine and quinoline) farther from or in the absence of the transmission line. The observed differences between natural and anthropogenic ion spectra near HVDC lines are attributed primarily to a shortening of ion lifetimes by the strong electric field associated with the HVDC lines. One exception is the production of potassium and probably sodium based ions from the decomposition of insects in transmission line coronas. 22 refs., 29 figs.

Eisele, F.L.

1989-05-01T23:59:59.000Z

24

High voltage pulse conditioning  

DOE Patents [OSTI]

Apparatus for conditioning high voltage pulses from particle accelerators in order to shorten the rise times of the pulses. Flashover switches in the cathode stalk of the transmission line hold off conduction for a determinable period of time, reflecting the early portion of the pulses. Diodes upstream of the switches divert energy into the magnetic and electrostatic storage of the capacitance and inductance inherent to the transmission line until the switches close.

Springfield, Ray M. (Sante Fe, NM); Wheat, Jr., Robert M. (Los Alamos, NM)

1990-01-01T23:59:59.000Z

25

High voltage RF feedthrough bushing  

DOE Patents [OSTI]

Described is a multi-element, high voltage radio frequency bushing for trmitting RF energy to an antenna located in a vacuum container. The bushing includes a center conductor of complex geometrical shape, an outer coaxial shield conductor, and a thin-walled hollow truncated cone insulator disposed between central and outer conductors. The shape of the center conductor, which includes a reverse curvature portion formed of a radially inwardly directed shoulder and a convex portion, controls the uniformity of the axial surface gradient on the insulator cone. The outer shield has a first substantially cylindrical portion and a second radially inwardly extending truncated cone portion.

Grotz, Glenn F. (Huntington Station, NY)

1984-01-01T23:59:59.000Z

26

High voltage DC power supply  

DOE Patents [OSTI]

A high voltage DC power supply having a first series resistor at the output for limiting current in the event of a short-circuited output, a second series resistor for sensing the magnitude of output current, and a voltage divider circuit for providing a source of feedback voltage for use in voltage regulation is disclosed. The voltage divider circuit is coupled to the second series resistor so as to compensate the feedback voltage for a voltage drop across the first series resistor. The power supply also includes a pulse-width modulated control circuit, having dual clock signals, which is responsive to both the feedback voltage and a command voltage, and also includes voltage and current measuring circuits responsive to the feedback voltage and the voltage developed across the second series resistor respectively. 7 figs.

Droege, T.F.

1989-12-19T23:59:59.000Z

27

High voltage DC power supply  

DOE Patents [OSTI]

A high voltage DC power supply having a first series resistor at the output for limiting current in the event of a short-circuited output, a second series resistor for sensing the magnitude of output current, and a voltage divider circuit for providing a source of feedback voltage for use in voltage regulation is disclosed. The voltage divider circuit is coupled to the second series resistor so as to compensate the feedback voltage for a voltage drop across the first series resistor. The power supply also includes a pulse-width modulated control circuit, having dual clock signals, which is responsive to both the feedback voltage and a command voltage, and also includes voltage and current measuring circuits responsive to the feedback voltage and the voltage developed across the second series resistor respectively.

Droege, Thomas F. (Batavia, IL)

1989-01-01T23:59:59.000Z

28

High voltage stability performance of a gamma ray detection device  

SciTech Connect (OSTI)

An industrial grade digital radiation survey meter device is currently being developed at Malaysian Nuclear Agency. This device used a cylindrical type Geiger Mueller (GM) which acts as a detector. GM detector operates at relatively high direct current voltages depend on the type of GM tube. This thin/thick walled cylindrical type of GM tube operates at 450-650 volts range. Proper value and stability performance of high voltage are important parameters to ensure that this device give a reliable radiation dose measurement. This paper will present an assessment of the stability and performance of the high voltage supply for radiation detector. The assessment is performed using System Identification tools box in MATLAB and mathematical statistics.

Abdullah, Nor Arymaswati; Lombigit, Lojius; Rahman, Nur Aira Abd [Technical Support Division, Malaysian Nuclear Agency, 43000 Kajang, Selangor (Malaysia)

2014-02-12T23:59:59.000Z

29

Radio-frequency powered glow discharge device and method with high voltage interface  

DOE Patents [OSTI]

A high voltage accelerating potential, which is supplied by a high voltage direct current power supply, is applied to the electrically conducting interior wall of an RF powered glow discharge cell. The RF power supply desirably is electrically grounded, and the conductor carrying the RF power to the sample held by the probe is desirably shielded completely excepting only the conductor's terminal point of contact with the sample. The high voltage DC accelerating potential is not supplied to the sample. A high voltage capacitance is electrically connected in series between the sample on the one hand and the RF power supply and an impedance matching network on the other hand. The high voltage capacitance isolates the high DC voltage from the RF electronics, while the RF potential is passed across the high voltage capacitance to the plasma. An inductor protects at least the RF power supply, and desirably the impedance matching network as well, from a short that might occur across the high voltage capacitance. The discharge cell and the probe which holds the sample are configured and disposed to prevent the probe's components, which are maintained at ground potential, from bridging between the relatively low vacuum region in communication with the glow discharge maintained within the cell on the one hand, and the relatively high vacuum region surrounding the probe and cell on the other hand. The probe and cell also are configured and disposed to prevent the probe's components from electrically shorting the cell's components. 11 figures.

Duckworth, D.C.; Marcus, R.K.; Donohue, D.L.; Lewis, T.A.

1994-06-28T23:59:59.000Z

30

Temperature controlled high voltage regulator  

DOE Patents [OSTI]

A temperature controlled high voltage regulator for automatically adjusting the high voltage applied to a radiation detector is described. The regulator is a solid state device that is independent of the attached radiation detector, enabling the regulator to be used by various models of radiation detectors, such as gas flow proportional radiation detectors.

Chiaro, Jr., Peter J. (Clinton, TN); Schulze, Gerald K. (Knoxville, TN)

2004-04-20T23:59:59.000Z

31

Modular high voltage power supply for chemical analysis  

DOE Patents [OSTI]

A high voltage power supply for use in a system such as a microfluidics system, uses a DC-DC converter in parallel with a voltage-controlled resistor. A feedback circuit provides a control signal for the DC-DC converter and voltage-controlled resistor so as to regulate the output voltage of the high voltage power supply, as well as, to sink or source current from the high voltage supply.

Stamps, James F. (Livermore, CA); Yee, Daniel D. (Dublin, CA)

2010-05-04T23:59:59.000Z

32

Measurement of high voltage using Rutherford backscattering spectrometry  

E-Print Network [OSTI]

A novel variation of Rutherford Backscattering Spectrometry (RBS) has been utilized to measure a high voltage collected on an aluminum target by Direct Energy Conversion. The maximum high voltage on the target was measured to be 97.5 kV +/- 2 kV...

Abrego, Celestino Pete

2007-04-25T23:59:59.000Z

33

> REPLACE THIS LINE WITH YOUR PAPER IDENTIFICATION NUMBER (DOUBLE-CLICK HERE TO EDIT) < 1 Abstract--In high current, high voltage, high temperature  

E-Print Network [OSTI]

and high current applications, such as HVDC transmission [1] or pulsed power application [2], a thyristor

Paris-Sud XI, Université de

34

High voltage load resistor array  

DOE Patents [OSTI]

A high voltage resistor comprising an array of a plurality of parallel electrically connected resistor elements each containing a resistive solution, attached at each end thereof to an end plate, and about the circumference of each of the end plates, a corona reduction ring. Each of the resistor elements comprises an insulating tube having an electrode inserted into each end thereof and held in position by one or more hose clamps about the outer periphery of the insulating tube. According to a preferred embodiment, the electrode is fabricated from stainless steel and has a mushroom shape at one end, that inserted into the tube, and a flat end for engagement with the end plates that provides connection of the resistor array and with a load.

Lehmann, Monty Ray (Smithfield, VA)

2005-01-18T23:59:59.000Z

35

High Voltage Electrolyte for Lithium Batteries  

Broader source: Energy.gov (indexed) [DOE]

battery using high voltage high energy cathode materials to enable large-scale, cost competitive production of the next generation of electric-drive vehicles. To...

36

Development of High Voltage Electron Microscope  

Science Journals Connector (OSTI)

......Cockcroft Walton Type High Voltage Generator. O Power Line O Fig. 4...pressure in the tank to the atmospheric pressure by removing freon...pump using liquid nitrogen. Water buffer and liquid nitrogen...base plate of high voltage generator. Four poles stand on this......

Shinjiro KATAGIRI; Hirokazu KIMURA; Susumu OZASA; Kazumi SHIRAISHI

1969-01-01T23:59:59.000Z

37

Limitations of High-Voltage Insulation  

Science Journals Connector (OSTI)

... materials such as impregnated paper. The important electrical properties of the materials used for the insulation of high-voltage circuits are conductivity and electric strength. The conductivity measures the ability ... a million times between themselves, but they are all classified as available for high-voltage insulation.

1938-01-08T23:59:59.000Z

38

High Voltage Safety Act | Department of Energy  

Broader source: Energy.gov (indexed) [DOE]

High Voltage Safety Act High Voltage Safety Act High Voltage Safety Act < Back Eligibility Commercial Construction Developer General Public/Consumer Industrial Installer/Contractor Utility Savings Category Alternative Fuel Vehicles Hydrogen & Fuel Cells Buying & Making Electricity Water Home Weatherization Solar Wind Program Info State Georgia Program Type Safety and Operational Guidelines Siting and Permitting The purpose of the High Voltage Safety Act is to prevent injury to persons and property and interruptions of utility service resulting from accidental or inadvertent contact with high-voltage electric lines by providing that no work shall be done in the vicinity of such lines unless and until the owner or operator thereof has been notified of such work and has taken the appropriate safety measures. The Georgia Public Service Commission requires

39

Current Direct Neutrino Mass Experiments  

E-Print Network [OSTI]

In this contribution we review the status and perspectives of direct neutrino mass experiments. These experiments investigate the kinematics of $\\beta$-decays of specific isotopes ($^3$H, $^{187}$Re, $^{163}$Ho) to derive model-independent information on the averaged electron (anti-) neutrino mass, which is formed by the incoherent sum of the neutrino mass eigenstates contributing to the electron neutrino. We first review the kinematics of $\\beta$-decay and the determination of the neutrino mass, before giving a brief overview of past neutrino mass measurements (SN1987a-ToF studies, Mainz and Troitsk experiments for $^3$H, cryo-bolometers for $^{187}$Re). We then describe the Karlsruhe Tritium Neutrino (KATRIN) experiment which is currently under construction at Karlsruhe Institute of Technology. The large-scale setup will use the MAC-E-Filter principle pioneered earlier to push the sensitivity down to a value of 200 meV(90% C.L.). KATRIN faces many technological challenges that have to be resolved with regar...

Drexlin, G; Mertens, S; Weinheimer, C

2013-01-01T23:59:59.000Z

40

ABBGroup-1-High voltage lab  

E-Print Network [OSTI]

A DISTRIBUTION MEDIUM AND LOW VOLTAGE HV circuit breakers #12;©ABBGroup-4- 3-Sep-07 When a breaker fails to interrupt the current... Fault arc at a disconnector Fault arc in a substation #12;©ABBGroup-5- 3-Sep-07/costs A detailed understanding of arc physics and fluid dynamics is necessary for the development of HV circuit

Basse, Nils Plesner

Note: This page contains sample records for the topic "high-voltage direct current" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Assessment of research directions for high voltage direct current power systems. Quarterly technical progress report, October 1, 1980-December 31, 1980  

SciTech Connect (OSTI)

Activities during this quarterly period on proposed HVDC systems research are reported. These activities include studies of HVDC converters, computerized simulation of HVDC systems, circuit breakers, and long-range planning of HVDC projects. (LCL)

Long, W F

1981-01-01T23:59:59.000Z

42

Graz University of Technology Institute of High Voltage Engineering and System Performance  

E-Print Network [OSTI]

.hspt@tugraz.at u www.hspt.tugraz.at Institute of High Voltage Engineering and System Performance Test Laboratory systems Test of insulators, fittings and accessories Testing of high voltage equipment Impulse voltage and current tests On-site-test of medium voltage cables Electrical methods in environmental technology

43

Vehicle Technologies Office Merit Review 2014: High-Voltage Solid...  

Broader source: Energy.gov (indexed) [DOE]

High-Voltage Solid Polymer Batteries for Electric Drive Vehicles Vehicle Technologies Office Merit Review 2014: High-Voltage Solid Polymer Batteries for Electric Drive Vehicles...

44

High-Voltage Solid Polymer Batteries for Electric Drive Vehicles...  

Broader source: Energy.gov (indexed) [DOE]

High-Voltage Solid Polymer Batteries for Electric Drive Vehicles High-Voltage Solid Polymer Batteries for Electric Drive Vehicles 2013 DOE Hydrogen and Fuel Cells Program and...

45

High-Voltage Solid Polymer Batteries for Electric Drive Vehicles...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

High-Voltage Solid Polymer Batteries for Electric Drive Vehicles High-Voltage Solid Polymer Batteries for Electric Drive Vehicles 2012 DOE Hydrogen and Fuel Cells Program and...

46

Definition: Direct current | Open Energy Information  

Open Energy Info (EERE)

Definition Definition Edit with form History Facebook icon Twitter icon » Definition: Direct current Jump to: navigation, search Dictionary.png Direct current A type of electricity transmission and distribution by which electricity flows in one direction through the conductor, usually relatively low voltage and high current (such as from a battery). To be used for typical 120 volt or 220 volt household appliances, DC must be converted to alternating current (AC).[1][2] View on Wikipedia Wikipedia Definition Direct current (DC) is the unidirectional flow of electric charge. Direct current is produced by sources such as batteries, thermocouples, solar cells, and commutator-type electric machines of the dynamo type. Direct current may flow in a conductor such as a wire, but can also flow

47

Design & Fabrication of a High-Voltage Photovoltaic Cell  

SciTech Connect (OSTI)

Silicon photovoltaic (PV) cells are alternative energy sources that are important in sustainable power generation. Currently, applications of PV cells are limited by the low output voltage and somewhat low efficiency of such devices. In light of this fact, this project investigates the possibility of fabricating high-voltage PV cells on float-zone silicon wafers having output voltages ranging from 50 V to 2000 V. Three designs with different geometries of diffusion layers were simulated and compared in terms of metal coverage, recombination, built-in potential, and conduction current density. One design was then chosen and optimized to be implemented in the final device design. The results of the simulation serve as a feasibility test for the design concept and provide supportive evidence of the effectiveness of silicon PV cells as high-voltage power supplies.

Felder, Jennifer; /North Carolina State U. /SLAC

2012-09-05T23:59:59.000Z

48

Optically triggered high voltage switch network and method for switching a high voltage  

DOE Patents [OSTI]

An optically triggered solid state switch and method for switching a high voltage electrical current. A plurality of solid state switches (350) are connected in series for controlling electrical current flow between a compensation capacitor (112) and ground in a reactive power compensator (50, 50') that monitors the voltage and current flowing through each of three distribution lines (52a, 52b and 52c), which are supplying three-phase power to one or more inductive loads. An optical transmitter (100) controlled by the reactive power compensation system produces light pulses that are conveyed over optical fibers (102) to a switch driver (110') that includes a plurality of series connected optical triger circuits (288). Each of the optical trigger circuits controls a pair of the solid state switches and includes a plurality of series connected resistors (294, 326, 330, and 334) that equalize or balance the potential across the plurality of trigger circuits. The trigger circuits are connected to one of the distribution lines through a trigger capacitor (340). In each switch driver, the light signals activate a phototransistor (300) so that an electrical current flows from one of the energy reservoir capacitors through a pulse transformer (306) in the trigger circuit, producing gate signals that turn on the pair of serially connected solid state switches (350).

El-Sharkawi, Mohamed A. (Renton, WA); Andexler, George (Everett, WA); Silberkleit, Lee I. (Mountlake Terrace, WA)

1993-01-19T23:59:59.000Z

49

High-voltage pulsed discharge in an electron source with a plasma cathode  

Science Journals Connector (OSTI)

The nature of and mechanism for producing a high-voltage discharge in an electron source with a plasma cathode are investigated. The possibility of generating pulsed electron currents with an amplitude of 103–104

S. P. Bugaev; F. Ya. Zagulov

1973-10-01T23:59:59.000Z

50

High-voltage supply for backward-wave tube  

SciTech Connect (OSTI)

A high-current high-voltage supply for a backward-wave tube is described that uses a generalppurpose semiconductor converter with pulse-width modulation and two-stage regulation. The load current is up to 250 mA for load voltages of from 0.5 to 4.5 kV. The voltage staiblity is less than or equal to 5 x 10/sup -6/. the root-mean-square output ripple is less than or equal to 2 x 10/sup -6// The supply is equipped with high-speed (5 usec) load-breakdown protection.

Bryvkhanov, A.N.; Kosarev, P.M.; Latushkin, S.T.; Yudin, L.I.

1986-04-01T23:59:59.000Z

51

High Power, High Voltage FETs in Linear Applications: A User's Perspective  

SciTech Connect (OSTI)

The specifications of the current crop of highpower, high-voltage field-effect transistors (FETs) can lure a designer into employing them in high-voltage DC equipment. Devices with extremely low on-resistance and very high power ratings are available from several manufacturers. However, our experience shows that high-voltage, linear operation of these devices at near-continuous duty can present difficult reliability challenges at stress levels well-below their published specifications. This paper chronicles the design evolution of a 600 volt, 8 ampere shunt regulator for use with megawatt-class radio transmitters, and presents a final design that has met its reliability criteria.

N. Greenough, E. Fredd, S. DePasquale

2009-09-21T23:59:59.000Z

52

High-voltage R-F feedthrough bushing  

DOE Patents [OSTI]

Described is a multi-element, high voltage radio frequency bushing for transmitting rf energy to an antenna located in a vacuum container. The bushing includes a center conductor of complex geometrical shape, an outer coaxial shield conductor, and a thin-walled hollow truncated cone insulator disposed between central and outer conductors. The shape of the center conductor, which includes a reverse curvature portion formed of a radially inwardly directed shoulder and a convex portion, controls the uniformity of the axial surface gradient on the insulator cone. The outer shield has a first substantially cylindrical portion and a second radially inwardly extending truncated cone portion.

Grotz, G.F.

1982-09-03T23:59:59.000Z

53

Safe epoxy encapsulant for high voltage magnetics  

SciTech Connect (OSTI)

This paper describes the use of Formula 456, an aliphatic amine cured epoxy for impregnating coils and high voltage transformers. Sandia has evaluated a number of MDA-free epoxy encapsulants which relied on either anhydride or other aromatic amine curing agents. The use of aliphatic amine curing agents was more recently evaluated and has resulted in the definition of Formula 456 resin. Methylene dianiline (MDA) has been used for more than 20 years as the curing agent for various epoxy formulations throughout the Department of Energy and much of industry. Sandia National Laboratories began the process of replacing MDA with other formulations because of regulations imposed by OSHA on the use of MDA. OSHA has regulated MDA because it is a suspect carcinogen. Typically the elimination of OSHA-regulated materials provides a rare opportunity to qualify new formulations in a range of demanding applications. It was important to take full advantage of that opportunity, although the associated materials qualification effort was costly. Small high voltage transformers are one of those demanding applications. The successful implementation of the new formulation for high reliability transformers will be described. The test results that demonstrate the parts are qualified for use in DOE weapon systems will be presented.

Sanchez, R.O.; Archer, W.E.

1998-01-01T23:59:59.000Z

54

E-beam high voltage switching power supply  

DOE Patents [OSTI]

A high-power power supply produces a controllable, constant high voltage put under varying and arcing loads. The power supply includes a voltage regulator, an inductor, an inverter for producing a high frequency square wave current of alternating polarity, an improved inverter voltage clamping circuit, a step up transformer, an output rectifier for producing a dc voltage at the output of each module, and a current sensor for sensing output current. The power supply also provides dynamic response to varying loads by controlling the voltage regulator duty cycle and circuitry is provided for sensing incipient arc currents at the output of the power supply to simultaneously decouple the power supply circuitry from the arcing load. The power supply includes a plurality of discrete switching type dc--dc converter modules.

Shimer, Daniel W. (Danville, CA); Lange, Arnold C. (Livermore, CA)

1996-01-01T23:59:59.000Z

55

E-beam high voltage switching power supply  

DOE Patents [OSTI]

A high-power power supply produces a controllable, constant high voltage output under varying and arcing loads. The power supply includes a voltage regulator, an inductor, an inverter for producing a high frequency square wave current of alternating polarity, an improved inverter voltage clamping circuit, a step up transformer, an output rectifier for producing a dc voltage at the output of each module, and a current sensor for sensing output current. The power supply also provides dynamic response to varying loads by controlling the voltage regulator duty cycle and circuitry is provided for sensing incipient arc currents at the output of the power supply to simultaneously decouple the power supply circuitry from the arcing load. The power supply includes a plurality of discrete switching type dc--dc converter modules. 5 figs.

Shimer, D.W.; Lange, A.C.

1996-10-15T23:59:59.000Z

56

High voltage electric substation performance in earthquakes  

SciTech Connect (OSTI)

This paper examines the performance of several types of high voltage substation equipment in past earthquakes. Damage data is provided in chart form. This data is then developed into a tool for estimating the performance of a substation subjected to an earthquake. First, suggests are made about the development of equipment class fragility curves that represent the expected earthquake performance of different voltages and types of equipment. Second, suggestions are made about how damage to individual pieces of equipment at a substation likely affects the post-earthquake performance of the substation as a whole. Finally, estimates are provided as to how quickly a substation, at various levels of damage, can be restored to operational service after the earthquake.

Eidinger, J. [G and E Engineering Systems, Oakland, CA (United States); Ostrom, D. [Southern California Edison, Rosemead, CA (United States); Matsuda, E. [Pacific Gas and Electric, San Francisco, CA (United States)

1995-12-31T23:59:59.000Z

57

Ocean indicators Current knowledge and future directions  

E-Print Network [OSTI]

Ocean indicators Current knowledge and future directions Brian Burke, NOAA Fisheries Brian.Burke@noaa.gov #12;· Review of ocean indicator work · Forecasting · Indicator gaps and the importance of mechanistic understanding · Plugging in to management #12;Haeseker et al. 2012 Ocean survival is low and variable #12;-10 -5

58

Current Directions in Freight and Logistics Industry  

E-Print Network [OSTI]

Current Directions in Freight and Logistics Industry CTS Freight and Logistics Symposium November- the-box #12;Perspective Be sure to look-up from time-to-time #12;Why Discuss Freight and Logistics....Large Part of the Economy Logistics Cost As A Percent of GDP ­ 10% Source: CSCMP State of Logistics 2007 #12

Minnesota, University of

59

High voltage overhead long transmission line design and fault analysis.  

E-Print Network [OSTI]

??The goal of this project is to design a reliable high voltage overhead long transmission line that satisfies specific design criteria including voltage regulation, efficiency,… (more)

Elzain, Mohamed Ali

2011-01-01T23:59:59.000Z

60

fault diagnosis of a high voltage transmission line using waveform ...  

E-Print Network [OSTI]

Oct 4, 2013 ... FAULT DIAGNOSIS OF A HIGH VOLTAGE TRANSMISSION LINE USING ... Fault types such as single line to ground, line to line, double line to ...

Ripunjoy Phukan

2013-10-04T23:59:59.000Z

Note: This page contains sample records for the topic "high-voltage direct current" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Soft-commutated direct current motor  

DOE Patents [OSTI]

A method and circuit is disclosed for soft-commutation of a direct current (DC) motor. An attenuation circuit is connected through auxiliary brushes A, A[prime], B and B[prime] to the commutator (16) to drain circuit from successive armature coils (15) before the main brushes (27, 28) disconnects from each of the coils (15). This prevents the spark generation that normally occurs in conventional DC motors. The attenuation circuit may also be connected before energization of the coil (15) for a soft turning on operation. 13 figs.

Hsu, J.S.

1999-07-27T23:59:59.000Z

62

The Cavendish high-voltage laboratory 1935–39  

Science Journals Connector (OSTI)

...the period covered. Nuclear Transmutation|Cavendish...development of high-voltage nuclear transmutation equipment...experimental work in nuclear physics though he continued...a new high-voltage accelerator therefore fell mainly...doubler circuit with six vacuum rectifiers forming a...

1999-01-01T23:59:59.000Z

63

Advanced Gate Drive for the SNS High Voltage Converter Modulator  

SciTech Connect (OSTI)

SLAC National Accelerator Laboratory is developing a next generation H-bridge switch plate [1], a critical component of the SNS High Voltage Converter Modulator [2]. As part of that effort, a new IGBT gate driver has been developed. The drivers are an integral part of the switch plate, which are essential to ensuring fault-tolerant, high-performance operation of the modulator. The redesigned driver improves upon the existing gate drive in several ways. The new gate driver has improved fault detection and suppression capabilities; suppression of shoot-through and over-voltage conditions, monitoring of dI/dt and Vce(sat) for fast over-current detection and suppression, and redundant power isolation are some of the added features. In addition, triggering insertion delay is reduced by a factor of four compared to the existing driver. This paper details the design and performance of the new IGBT gate driver. A simplified schematic and description of the construction are included. The operation of the fast over-current detection circuits, active IGBT over-voltage protection circuit, shoot-through prevention circuitry, and control power isolation breakdown detection circuit are discussed.

Nguyen, M.N.; Burkhart, C.; Kemp, M.A.; /SLAC; Anderson, D.E.; /Oak Ridge

2009-05-07T23:59:59.000Z

64

High voltage electrical amplifier having a short rise time  

DOE Patents [OSTI]

A circuit, comprising an amplifier and a transformer is disclosed that produces a high power pulse having a fast response time, and that responds to a digital control signal applied through a digital-to-analog converter. The present invention is suitable for driving a component such as an electro-optic modulator with a voltage in the kilovolt range. The circuit is stable at high frequencies and during pulse transients, and its impedance matching circuit matches the load impedance with the output impedance. The preferred embodiment comprises an input stage compatible with high-speed semiconductor components for amplifying the voltage of the input control signal, a buffer for isolating the input stage from the output stage; and a plurality of current amplifiers connected to the buffer. Each current amplifier is connected to a field effect transistor (FET), which switches a high voltage power supply to a transformer which then provides an output terminal for driving a load. The transformer comprises a plurality of transmission lines connected to the FETs and the load. The transformer changes the impedance and voltage of the output. The preferred embodiment also comprises a low voltage power supply for biasing the FETs at or near an operational voltage.

Christie, David J. (Pleasanton, CA); Dallum, Gregory E. (Livermore, CA)

1991-01-01T23:59:59.000Z

65

High-voltage air-core pulse transformers  

SciTech Connect (OSTI)

General types of air core pulse transformers designed for high voltage pulse generation and energy transfer applications are discussed with special emphasis on pulse charging systems which operate up to the multi-megavolt range. The design, operation, dielectric materials, and performance are described. It is concluded that high voltage air core pulse transformers are best suited to applications outside the normal ranges of conventional magnetic core transformers. In general these include charge transfer at high power levels and fast pulse generation with comparatively low energy. When properly designed and constructed, they are capable of delivering high energy transfer efficiency and have demonstrated superior high voltage endurance. The principal disadvantage of high voltage air core transformers is that they are not generally available from commercial sources. Consequently, the potential user must become thoroughly familiar with all aspects of design, fabrication and system application before he can produce a high performance transformer system. (LCL)

Rohwein, G. J.

1981-01-01T23:59:59.000Z

66

High Voltage Electrolytes for Li-ion Batteries | Department of...  

Broader source: Energy.gov (indexed) [DOE]

Electrolytes for Li-ion Batteries High Voltage Electrolytes for Li-ion Batteries 2011 DOE Hydrogen and Fuel Cells Program, and Vehicle Technologies Program Annual Merit Review and...

67

Living and Working Safely Around High-Voltage Power Lines.  

SciTech Connect (OSTI)

High-voltage transmission lines can be just as safe as the electrical wiring in the homes--or just as dangerous. The crucial factor is ourselves: they must learn to behave safely around them. This booklet is a basic safety guide for those who live and work around power lines. It deals primarily with nuisance shocks due to induced voltages, and with potential electric shock hazards from contact with high-voltage lines. References on possible long-term biological effects of transmission lines are shown. In preparing this booklet, the Bonneville Power Administration has drawn on more than 50 years of experience with high-voltage transmission. BPA operates one of the world`s largest networks of long-distance, high-voltage lines. This system has more than 400 substations and about 15,000 miles of transmission lines, almost 4,400 miles of which are operated at 500,000 volts.

United States. Bonneville Power Administration.

2001-06-01T23:59:59.000Z

68

High Voltage Electrolytes for Li-ion Batteries | Department of...  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

in Support of 5 V Li-ion Chemistries Vehicle Technologies Office Merit Review 2014: Fluorinated Electrolyte for 5-V Li-Ion Chemistry High Voltage Electrolyte for Lithium Batteries...

69

High voltage dry-type air-core shunt reactors  

Science Journals Connector (OSTI)

Dry-type air-core shunt reactors are now being ... systems to limit overvoltages. Recently, high voltage dry-type air-core shunt reactors have been designed, ... transient overvoltages and electrical and magnetic...

Klaus Papp; Michael R. Sharp…

2014-11-01T23:59:59.000Z

70

High voltage power supply with modular series resonant inverters  

DOE Patents [OSTI]

A relatively small and compact high voltage, high current power supply for a laser utilizes a plurality of modules containing series resonant half bridge inverters. A pair of reverse conducting thyristors are incorporated in each series resonant inverter module such that the series resonant inverter modules are sequentially activated in phases 360.degree./n apart, where n=number of modules for n>2. Selective activation of the modules allows precise output control reducing ripple and improving efficiency. Each series resonant half bridge inverter module includes a transformer which has a cooling manifold for actively circulating a coolant such as water, to cool the transformer core as well as selected circuit elements. Conductors connecting and forming various circuit components comprise hollow, electrically conductive tubes such as copper. Coolant circulates through the tubes to remove heat. The conductive tubes act as electrically conductive lines for connecting various components of the power supply. Where it is desired to make electrical isolation breaks, tubes comprised of insulating material such as nylon are used to provide insulation and continue the fluid circuit.

Dreifuerst, Gary R. (Livermore, CA); Merritt, Bernard T. (Livermore, CA)

1995-01-01T23:59:59.000Z

71

High voltage power supply with modular series resonant inverters  

DOE Patents [OSTI]

A relatively small and compact high voltage, high current power supply for a laser utilizes a plurality of modules containing series resonant half bridge inverters. A pair of reverse conducting thyristors are incorporated in each series resonant inverter module such that the series resonant inverter modules are sequentially activated in phases 360{degree}/n apart, where n=number of modules for n>2. Selective activation of the modules allows precise output control reducing ripple and improving efficiency. Each series resonant half bridge inverter module includes a transformer which has a cooling manifold for actively circulating a coolant such as water, to cool the transformer core as well as selected circuit elements. Conductors connecting and forming various circuit components comprise hollow, electrically conductive tubes such as copper. Coolant circulates through the tubes to remove heat. The conductive tubes act as electrically conductive lines for connecting various components of the power supply. Where it is desired to make electrical isolation breaks, tubes comprised of insulating material such as nylon are used to provide insulation and continue the fluid circuit. 11 figs.

Dreifuerst, G.R.; Merritt, B.T.

1995-07-18T23:59:59.000Z

72

E-beam high voltage switching power supply  

DOE Patents [OSTI]

A high power, solid state power supply is described for producing a controllable, constant high voltage output under varying and arcing loads suitable for powering an electron beam gun or other ion source. The present power supply is most useful for outputs in a range of about 100-400 kW or more. The power supply is comprised of a plurality of discrete switching type dc-dc converter modules, each comprising a voltage regulator, an inductor, an inverter for producing a high frequency square wave current of alternating polarity, an improved inverter voltage clamping circuit, a step up transformer, and an output rectifier for producing a dc voltage at the output of each module. The inputs to the converter modules are fed from a common dc rectifier/filter and are linked together in parallel through decoupling networks to suppress high frequency input interactions. The outputs of the converter modules are linked together in series and connected to the input of the transmission line to the load through a decoupling and line matching network. The dc-dc converter modules are phase activated such that for n modules, each module is activated equally 360{degree}/n out of phase with respect to a successive module. The phased activation of the converter modules, combined with the square current waveforms out of the step up transformers, allows the power supply to operate with greatly reduced output capacitance values which minimizes the stored energy available for discharge into an electron beam gun or the like during arcing. The present power supply also provides dynamic response to varying loads by controlling the voltage regulator duty cycle using simulated voltage feedback signals and voltage feedback loops. Circuitry is also provided for sensing incipient arc currents reflected at the output of the power supply and for simultaneously decoupling the power supply circuitry from the arcing load. 7 figs.

Shimer, D.W.; Lange, A.C.

1997-03-11T23:59:59.000Z

73

E-beam high voltage switching power supply  

DOE Patents [OSTI]

A high power, solid state power supply is described for producing a controllable, constant high voltage output under varying and arcing loads suitable for powering an electron beam gun or other ion source. The present power supply is most useful for outputs in a range of about 100-400 kW or more. The power supply is comprised of a plurality of discrete switching type dc-dc converter modules, each comprising a voltage regulator, an inductor, an inverter for producing a high frequency square wave current of alternating polarity, an improved inverter voltage clamping circuit, a step up transformer, and an output rectifier for producing a dc voltage at the output of each module. The inputs to the converter modules are fed from a common dc rectifier/filter and are linked together in parallel through decoupling networks to suppress high frequency input interactions. The outputs of the converter modules are linked together in series and connected to the input of the transmission line to the load through a decoupling and line matching network. The dc-dc converter modules are phase activated such that for n modules, each module is activated equally 360.degree./n out of phase with respect to a successive module. The phased activation of the converter modules, combined with the square current waveforms out of the step up transformers, allows the power supply to operate with greatly reduced output capacitance values which minimizes the stored energy available for discharge into an electron beam gun or the like during arcing. The present power supply also provides dynamic response to varying loads by controlling the voltage regulator duty cycle using simulated voltage feedback signals and voltage feedback loops. Circuitry is also provided for sensing incipient arc currents reflected at the output of the power supply and for simultaneously decoupling the power supply circuitry from the arcing load.

Shimer, Daniel W. (Danville, CA); Lange, Arnold C. (Livermore, CA)

1997-01-01T23:59:59.000Z

74

Accelerator System Development at High Voltage Engineering  

SciTech Connect (OSTI)

Throughout the years, HVE has continuously extended the capabilities of its accelerator systems to meet the rising demands from a diverse field of applications, among which are deep level ion implantation, micro-machining, neutron production for biomedical research, isotope production or accelerator mass spectrometry. Characteristic for HVE accelerators is the coaxial construction of the all solid state power supply around the acceleration tubes. With the use of solid state technology, the accelerators feature high stability and very low ripple. Terminal voltages range from 1 to 6 MV for HVE Singletrons and Tandetrons. The high-current versions of these accelerators can provide ion beams with powers of several kW. In the last years, several systems have been built with terminal voltages of 1.25 MV, 2 MV and 5 MV. Recently, the first system based on a 6 MV Tandetron has passed the factory tests. In this paper we describe the characteristics of the HVE accelerator systems and present as example recent systems.

Klein, M. G.; Gottdang, A.; Haitsma, R. G.; Mous, D. J. W. [High Voltage Engineering Europa B.V., P.O. Box 99, Amersfoort 3800 AB (Netherlands)

2009-03-10T23:59:59.000Z

75

Experiment Hazard Class 13.0 - High Voltage  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

3.0 - High Voltage 3.0 - High Voltage Applicability This hazard classification applies to all experiments involving the use of High Voltage Equipment. Other hazard classifications and their associated hazard controls may also apply to experiments in this hazard class. The inspection of electric equipment is covered under the APS Policy For User Electric Equipment Inspections. NOTE: Unless required Argonne training has been completed, users are not authorized to perform electrical work. Experiment Category All Hazard Class 13 experiments are categorized as medium risk experiments. Experiment Hazard Control Verification Statements Engineered Controls - Determined by review and results of a DEEI inspection of the equipment. Procedural Controls - Determined by review and results of a DEEI

76

Self-Excited ac High Voltage Generation Using Water Droplets  

Science Journals Connector (OSTI)

By letting water drops fall through rings into cans high voltage can be spontaneously generated with no external electrical excitation. Previous work concerning this type of electric influence machine for dc and three-phase ac high voltage generation is extended to include multiphase multifrequency operation by considering N streams and N cans. A distributed equivalent circuit representation is used to calculate the natural frequencies of the system where it is found that many overstable modes are present. Experimental observations with up to five cans are presented. This device can serve as a model for phenomena concerned with atmospheric electricity.

Markus Zahn

1973-01-01T23:59:59.000Z

77

Direct-Current Resistivity Survey At Mauna Loa Northeast Rift...  

Open Energy Info (EERE)

Mauna Loa Northeast Rift Area (Thomas, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Mauna Loa...

78

Direct-Current Resistivity At Cove Fort Area - Liquid (Warpinski...  

Open Energy Info (EERE)

Warpinski, Et Al., 2004) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity At Cove Fort Area - Liquid (Warpinski, Et...

79

Field Optimization of Three Dimensional High Voltage C. Trinitis  

E-Print Network [OSTI]

Field Optimization of Three Dimensional High Voltage Equipment C. Trinitis Lehrstuhl f The goal of finding an optimal electric field strength distribution for arbitrary three di­ mensional­ cal optimization algorithm. The package ob­ tained from these three components is then able

Stamatakis, Alexandros

80

High voltage gas insulated transmission line with continuous particle trapping  

DOE Patents [OSTI]

This invention provides a novel high voltage gas insulated transmission line utilizing insulating supports spaced at intervals with snap-in means for supporting a continuous trapping apparatus and said trapping apparatus having perforations and cutouts to facilitate trapping of contaminating particles and system flexibility.

Cookson, Alan H. (Pittsburgh, PA); Dale, Steinar J. (Monroeville, PA)

1983-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "high-voltage direct current" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

High Voltage DC Transmission 2 1.0 Introduction  

E-Print Network [OSTI]

1 High Voltage DC Transmission 2 1.0 Introduction Interconnecting HVDC within an AC system requires on use of switching devices collectively referred to in the HVDC community as valves. Valves may be non. Fig. 1 There have been three types of devices for implementing HVDC converter circuits: mercury

McCalley, James D.

82

Summaries of Addresses of Presidents of Sections: High-Voltage Insulation  

Science Journals Connector (OSTI)

... subject of his presidential address to Section A (Mathematics and Physics) *'High-voltage Insulation".

1963-08-31T23:59:59.000Z

83

Category:Direct-Current Resistivity Survey | Open Energy Information  

Open Energy Info (EERE)

source source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Category Edit History Facebook icon Twitter icon » Category:Direct-Current Resistivity Survey Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Geothermalpower.jpg Looking for the Direct-Current Resistivity Survey page? For detailed information on Direct-Current Resistivity Survey as exploration techniques, click here. Category:Direct-Current Resistivity Survey Add.png Add a new Direct-Current Resistivity Survey Technique Subcategories This category has the following 2 subcategories, out of 2 total. E [×] Electrical Profiling Configurations‎ 3 pages V [×] Vertical Electrical Sounding Configurations‎ 2 pages

84

High Voltage Testing of a 5-meter Prototype Triaxial HTS Cable  

SciTech Connect (OSTI)

High voltage tests were performed on a 5-m long prototype triaxial HTS cable (supplied by Ultera) at ORNL in preparation for installation of a 200-m HTS cable of the same design at the AEP utility substation in Columbus, Ohio. The triaxial design comprises three concentric phases and shield around a common former with the phase to phase dielectric at cryogenic temperature. Advantages of this design include increased current density, a reduced amount of HTS tape needed, and reduced heat load. The phase to phase voltage will be 13.2 kVrms (7.6 kVrms to ground). Preliminary testing was done on half-scale and full-scale terminations which successfully passed AC withstand, partial discharge, and impulse tests. High voltage tests conducted on the 5-m cable with the cable straight and after bending 90 degrees were ac withstand to 39 kVrms, partial discharge inception, and a minimum of 10 positive and 10 negative lightning waveform impulses at 110 kV. Phase to phase insulation was tested by applying high voltage to each phase one at a time with all the other phases grounded. Partial discharge data will be presented. The 5-m prototype triaxial HTS cable passed all the HV tests performed, with a PD inception voltage significantly above the required voltage.

Sauers, Isidor [ORNL; James, David Randy [ORNL; Ellis, Alvin R [ORNL; Tuncer, Enis [ORNL; Pace, Marshall O [ORNL; Gouge, Michael J [ORNL; Demko, Jonathan A [ORNL; Lindsay, David T [ORNL

2007-01-01T23:59:59.000Z

85

Design issues for high voltage converters for ion engines  

SciTech Connect (OSTI)

A design strategy is presented for a power converter for a high voltage ion engine for a spacecraft application. Various design issues such as appropriate topologies and control methods are considered. In this particular instance it was determined that a full bridge converter with phase shift gating and voltage mode control provided an efficient system with a minimum of electromagnetic interference. This system can be implemented in a straightforward manner, and it is relatively easy to protect from faults at the output.

King, R.J.; Stuart, T.A. [Univ. of Toledo, OH (United States)

1995-12-31T23:59:59.000Z

86

Direct-Current Resistivity Survey | Open Energy Information  

Open Energy Info (EERE)

Direct-Current Resistivity Survey Direct-Current Resistivity Survey Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Technique: Direct-Current Resistivity Survey Details Activities (65) Areas (34) Regions (4) NEPA(0) Exploration Technique Information Exploration Group: Geophysical Techniques Exploration Sub Group: Electrical Techniques Parent Exploration Technique: Electrical Techniques Information Provided by Technique Lithology: Rock type, mineral and clay content may be inferred. Stratigraphic/Structural: Determination of fracture zones, faults, depth to groundwater aquifers. Hydrological: Resistivity influenced by porosity, permeability, fluid saturation, fluid type and phase state of the pore water. Thermal: Resistivity influenced by temperature.[1] Cost Information

87

Direct-Current Resistivity At Blue Mountain Area (Fairbank Engineering,  

Open Energy Info (EERE)

Direct-Current Resistivity At Blue Mountain Area (Fairbank Engineering, Direct-Current Resistivity At Blue Mountain Area (Fairbank Engineering, 2005) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity At Blue Mountain Area (Fairbank Engineering, 2005) Exploration Activity Details Location Blue Mountain Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness not indicated DOE-funding Unknown Notes Geophysical surveys that have been conducted specifically for the geothermal program at Blue Mountain include a self-potential (SP) survey, and additional IP/electrical resistivity traversing. These surveys were conducted under a cooperative program between Noramex Corporation and the Energy and Geosciences Institute (EGI), University of Utah, with funding

88

Soft commutated direct current motor [summary of proposed paper  

SciTech Connect (OSTI)

A novel soft commutated direct current (DC) motor is introduced. The current of the commutated coil is intentionally drained before the brush disconnects the coil. This prevents the spark generation that normally occurs in conventional DC motors. A similar principle can be applied for DC generators.

Hsu, John S.

1998-10-22T23:59:59.000Z

89

Stray current interference control for HVDC earth currents  

SciTech Connect (OSTI)

High-voltage direct current (HVDC) transmission lines exist around the world, with several in the US. When one conductor must be taken out of operation (in case of emergency), the earth may be used as an alternate conductor. The earth current may be accumulated on and discharged from underground metallic structures that cross the voltage gradient created by the current. Test results on two lines showed that stray current interference is not a major problem if mitigated properly.

Fitzgerald, J.H. III [PSG Corrosion Engineering/Corrpro Cos., Detroit, MI (United States); Kroon, D.H. [Corrpro Companies Inc., Spring, TX (United States)

1995-06-01T23:59:59.000Z

90

Definition: Direct-Current Resistivity Survey | Open Energy Information  

Open Energy Info (EERE)

form form View source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Definition Edit with form History Facebook icon Twitter icon » Definition: Direct-Current Resistivity Survey Jump to: navigation, search Dictionary.png Direct-Current Resistivity Survey Direct-current (DC) resistivity is an active source electrical technique in which current is applied to the ground using electrodes and the earth response (voltage or potential difference) is recorded. This survey generates a geoelectric section of apparent resistivity and enables an inference of subsurface geology.[1] View on Wikipedia Wikipedia Definition References ↑ http://www.nga.com/Flyers_PDF/NGA_DC_Resistivity.pdf

91

Self-monitoring high voltage transmission line suspension insulator  

DOE Patents [OSTI]

A high voltage transmission line suspension insulator (18 or 22) which monitors its own dielectric integrity. A dielectric rod (10) has one larger diameter end fitting attachable to a transmission line and another larger diameter end fitting attachable to a support tower. The rod is enclosed in a dielectric tube (14) which is hermetically sealed to the rod's end fittings such that a liquidtight space (20) is formed between the rod and the tube. A pressurized dielectric liquid is placed within that space. A discoloring dye placed within this space is used to detect the loss of the pressurized liquid.

Stemler, Gary E. (Vancouver, WA); Scott, Donald N. (Vancouver, WA)

1981-01-01T23:59:59.000Z

92

A high voltage test stand for electron gun qualification for LINACs  

SciTech Connect (OSTI)

An electron gun lest stand has been developed at RRCAT. The test stand consists of a high voltage pulsed power supply, electron gun filament supply, grid supply, UHV system and electron gun current measurement system. Several electron guns developed indigenously were evaluated on this test stand. The shielding is provided for the electron gun set up. Electron gun tests can be tested upto 55 kV with pulse width of 15 microsecs and pulse repetition rates up to 200 Hz. The technical details of the subsystems are furnished and results of performance of the test stand have been reported in this paper. (author)

Wanmode, Yashwant D.; Mulchandani, J.; Acharya, M.; Bhisikar, A.; Singh, H.G.; Shrivastava, Purushottam, E-mail: yash@rrcat.gov.in [Pulsed High Power Microwave Section, Raja Ramanna Centre for Advanced Technology, Indore (India)

2011-07-01T23:59:59.000Z

93

Direct-Current Resistivity Survey At Blue Mountain Area (Fairbank  

Open Energy Info (EERE)

5) 5) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Blue Mountain Area (Fairbank Engineering, 2005) Exploration Activity Details Location Blue Mountain Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness not indicated DOE-funding Unknown Notes Geophysical surveys that have been conducted specifically for the geothermal program at Blue Mountain include a self-potential (SP) survey, and additional IP/electrical resistivity traversing. These surveys were conducted under a cooperative program between Noramex Corporation and the Energy and Geosciences Institute (EGI), University of Utah, with funding support from the DOE's Office of Geothermal Technology (DOE/OGT).

94

Seismic vulnerability assessment of a high voltage disconnect switch  

Science Journals Connector (OSTI)

Abstract This paper deals with the seismic vulnerability of high voltage equipment typically installed in electric substations. In particular, the seismic response of a 380 kV vertical disconnect switch has been investigated based on the results of an experimental campaign carried out at Roma Tre University. According to a series of non-linear analyses, the influence of the most significant parameters on the seismic behavior of this apparatus has been analyzed and the corresponding fragility curves have been evaluated by using the Effective Fragility Analysis method. The results showed a limited vulnerability of the disconnect switch, whose most critical parts are the bottom joint of the ceramic support column and the steel column base.

Fabrizio Paolacci; Renato Giannini; Silvia Alessandri; Gianmarco De Felice

2014-01-01T23:59:59.000Z

95

Monolithic high voltage nonlinear transmission line fabrication process  

DOE Patents [OSTI]

A process for fabricating sequential inductors and varistor diodes of a monolithic, high voltage, nonlinear, transmission line in GaAs is disclosed. An epitaxially grown laminate is produced by applying a low doped active n-type GaAs layer to an n-plus type GaAs substrate. A heavily doped p-type GaAs layer is applied to the active n-type layer and a heavily doped n-type GaAs layer is applied to the p-type layer. Ohmic contacts are applied to the heavily doped n-type layer where diodes are desired. Multiple layers are then either etched away or Oxygen ion implanted to isolate individual varistor diodes. An insulator is applied between the diodes and a conductive/inductive layer is thereafter applied on top of the insulator layer to complete the process. 6 figs.

Cooper, G.A.

1994-10-04T23:59:59.000Z

96

Monolithic high voltage nonlinear transmission line fabrication process  

DOE Patents [OSTI]

A process for fabricating sequential inductors and varactor diodes of a monolithic, high voltage, nonlinear, transmission line in GaAs is disclosed. An epitaxially grown laminate is produced by applying a low doped active n-type GaAs layer to an n-plus type GaAs substrate. A heavily doped p-type GaAs layer is applied to the active n-type layer and a heavily doped n-type GaAs layer is applied to the p-type layer. Ohmic contacts are applied to the heavily doped n-type layer where diodes are desired. Multiple layers are then either etched away or Oxygen ion implanted to isolate individual varactor diodes. An insulator is applied between the diodes and a conductive/inductive layer is thereafter applied on top of the insulator layer to complete the process.

Cooper, Gregory A. (346 Primrose Dr., Pleasant Hill, CA 94523)

1994-01-01T23:59:59.000Z

97

Transformer coupling for transmitting direct current through a barrier  

DOE Patents [OSTI]

The transmission system for transmitting direct current from an energy source on one side of an electrical and mechanical barrier to a load on the other side of the barrier utilizes a transformer comprising a primary core on one side of the transformer and a secondary core on the other side of the transformer. The cores are magnetically coupled selectively by moving a magnetic ferrite coupler in and out of alignment with the poles of the cores. The direct current from the energy source is converted to a time varying current by an oscillating circuit, which oscillating circuit is optically coupled to a secondary winding on the secondary core to interrupt oscillations upon the voltage in the secondary winding exceeding a preselected level. 4 figs.

Brown, R.L.; Guilford, R.P.; Stichman, J.H.

1987-06-29T23:59:59.000Z

98

Transformer coupling for transmitting direct current through a barrier  

DOE Patents [OSTI]

The transmission system for transmitting direct current from an energy source on one side of an electrical and mechanical barrier to a load on the other side of the barrier utilizes a transformer comprising a primary core on one side of the transformer and a secondary core on the other side of the transformer. The cores are magnetically coupled selectively by moving a magnetic ferrite coupler in and out of alignment with the poles of the cores. The direct current from the energy source is converted to a time varying current by an oscillating circuit, which oscillating circuit is optically coupled to a secondary winding on the secondary core to interrupt oscillations upon the voltage in the secondary winding exceeding a preselected level.

Brown, Ralph L. (Albuquerque, NM); Guilford, Richard P. (Albuquerque, NM); Stichman, John H. (Albuquerque, NM)

1988-01-01T23:59:59.000Z

99

Object Oriented Safety Analysis of an Extra High Voltage Substation Bay  

Science Journals Connector (OSTI)

Experiences of application of the object oriented approach to safety analysis of an extra high voltage substation bay are presented. As the first step...

Bartosz Nowicki; Janusz Górski

1998-01-01T23:59:59.000Z

100

The design, construction, and operation of long-distance high-voltage electricity transmission technologies.  

SciTech Connect (OSTI)

This report focuses on transmission lines, which operate at voltages of 115 kV and higher. Currently, the highest voltage lines comprising the North American power grid are at 765 kV. The grid is the network of transmission lines that interconnect most large power plants on the North American continent. One transmission line at this high voltage was built near Chicago as part of the interconnection for three large nuclear power plants southwest of the city. Lines at this voltage also serve markets in New York and New England, also very high demand regions. The large power transfers along the West Coast are generally at 230 or 500 kV. Just as there are practical limits to centralization of power production, there are practical limits to increasing line voltage. As voltage increases, the height of the supporting towers, the size of the insulators, the distance between conductors on a tower, and even the width of the right-of-way (ROW) required increase. These design features safely isolate the electric power, which has an increasing tendency to arc to ground as the voltage (or electrical potential) increases. In addition, very high voltages (345 kV and above) are subject to corona losses. These losses are a result of ionization of the atmosphere, and can amount to several megawatts of wasted power. Furthermore, they are a local nuisance to radio transmission and can produce a noticeable hum. Centralized power production has advantages of economies of scale and special resource availability (for instance, hydro resources), but centralized power requires long-distance transfers of power both to reach customers and to provide interconnections for reliability. Long distances are most economically served at high voltages, which require large-scale equipment and impose a substantial footprint on the corridors through which power passes. The most visible components of the transmission system are the conductors that provide paths for the power and the towers that keep these conductors at a safe distance from each other and from the ground and the natural and built environment. Common elements that are generally less visible (or at least more easily overlooked) include the maintained ROW along the path of the towers, access roads needed for maintenance, and staging areas used for initial construction that may be restored after construction is complete. Also visible but less common elements along the corridor may include switching stations or substations, where lines of similar or different voltages meet to transfer power.

Molburg, J. C.; Kavicky, J. A.; Picel, K. C.

2008-03-03T23:59:59.000Z

Note: This page contains sample records for the topic "high-voltage direct current" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Chapter 19. High Voltage Insulation, Diagnostics and Energetic Electron and Photon Beam Interactions  

E-Print Network [OSTI]

Chapter 19. High Voltage Insulation, Diagnostics and Energetic Electron and Photon Beam Interactions 19-1 High Voltage Insulation, Diagnostics and Energetic Electron and Photon Beam Interactions 1. DC Properties of Modern Filled Epoxy Insulation Academic and Research Staff Dr. Chathan Cooke Sponsor

102

An Approximate Dynamic Programming Algorithm for the Allocation of High-Voltage Transformer Spares in the  

E-Print Network [OSTI]

An Approximate Dynamic Programming Algorithm for the Allocation of High-Voltage Transformer Spares high-voltage transformer spares throughout the electric grid to mitigate the risk of random transformer-voltage transformers are an integral part of the electric transmission system. A catas- trophic transformer failure

Powell, Warren B.

103

Evaluation of Insulation Systems for the Optimal Design of High Voltage Pulse Transformers  

E-Print Network [OSTI]

This paper presents a study for the design of the insulation systems of high voltage pulse transformer based on experimental tests and numerical simulations. Data of high voltage tests on solid and liquid insulation materials are presented and discussed. The understanding of each part of the insulation is supported by electrostatic fields simulations.

Sylvain, Candolfi; Davide, Aguglia; Philippe, Viarouge; Jürgen, Biela; Jerome, Cros

2015-01-01T23:59:59.000Z

104

High-Voltage Broadband-Over-Powerline (HV-BPL) Field Test Report | Open  

Open Energy Info (EERE)

High-Voltage Broadband-Over-Powerline (HV-BPL) Field Test Report High-Voltage Broadband-Over-Powerline (HV-BPL) Field Test Report Jump to: navigation, search Tool Summary LAUNCH TOOL Name: High-Voltage Broadband-Over-Powerline (HV-BPL) Field Test Report Focus Area: Crosscutting Topics: Policy Impacts Website: www.netl.doe.gov/smartgrid/referenceshelf/reports/HV-BPL_Final_Report. Equivalent URI: cleanenergysolutions.org/content/high-voltage-broadband-over-powerline Language: English Policies: "Deployment Programs,Financial Incentives" is not in the list of possible values (Deployment Programs, Financial Incentives, Regulations) for this property. DeploymentPrograms: Technical Assistance This reports details findings from a pilot High Voltage Broadband over Power Line (HV-BPL) program, an effort to develop a disruptive technology

105

Direct-Current Resistivity At Central Nevada Seismic Zone Region  

Open Energy Info (EERE)

At Central Nevada Seismic At Central Nevada Seismic Zone Region (Pritchett, 2004) Exploration Activity Details Location Central Nevada Seismic Zone Geothermal Region Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes NOTE: These are theoretical/computer simulation tests of various methods on eight hypothetical 'model' basing-and-range geothermal systems. "The 300-meter heat flow holes are essentially useless for finding the "hidden" reservoirs. Clearly, the best results are obtained from the SP and MT surveys, with DC resistivity a close third. It is concluded that the best way to find "hidden" basin and range geothermal resources of this general type is to carry out simultaneous SP and low-frequency MT surveys, and then

106

Fundamental properties of field emission-driven direct current microdischarges  

SciTech Connect (OSTI)

For half a century, it has been known that the onset of field emission in direct current microdischarges with gap sizes less than 10 {mu}m can lead to breakdown at applied voltages far less than predicted by Paschen's law. It is still unclear how field emission affects other fundamental plasma properties at this scale. In this work, a one-dimensional fluid model is used to predict basic scaling laws for fundamental properties including ion density, electric field due to space charge, and current-voltage relations in the pre-breakdown regime. Computational results are compared with approximate analytic solutions. It is shown that field emission provides an abundance of cathode electrons, which in turn create large ion concentrations through ionizing collisions well before Paschen's criterion for breakdown is met. Breakdown due to ion-enhanced field emission occurs when the electric field due to space charge becomes comparable to the applied electric field. Simple scaling analysis of the 1D Poisson equation demonstrates that an ion density of n{sub +} Almost-Equal-To 0.1V{sub A}{epsilon}{sub 0}/qd{sup 2} is necessary to significantly distort the electric field. Defining breakdown in terms of this critical ion density leads analytically to a simple, effective secondary emission coefficient {gamma}{sup Prime} of the same mathematical form initially suggested by Boyle and Kisliuk [Phys. Rev. 97, 255 (1955)].

Rumbach, Paul; Go, David B. [Department of Aerospace and Mechanical Engineering, University of Notre Dame, Notre Dame, Indiana 46556 (United States)

2012-11-15T23:59:59.000Z

107

Direct-current-like Phase Space Manipulation Using Chirped Alternating Current Fields  

SciTech Connect (OSTI)

Waves in plasmas can accelerate particles that are resonant with the wave. A dc electric field also accelerates particles, but without a resonance discrimination, which makes the acceleration mechanism profoundly different. Whereas wave-particle acceleration mechanisms have been widely discussed in the literature, this work discusses the direct analogy between wave acceleration and dc field acceleration in a particular parameter regime explored in previous works. Apart from the academic interest of this correspondence, there may be practical advantages in using waves to mimic dc electric fields, for example, in driving plasma current with high efficiency.

P.F. Schmit and N.J. Fisch

2010-02-01T23:59:59.000Z

108

Hardware model of a shipboard zonal electrical distribution system (ZEDS) : alternating current/direct current (AC/DC)  

E-Print Network [OSTI]

A hardware model of a shipboard electrical distribution system based on aspects of the DDG 51 Flight IIA, Arleigh Burke class, 60Hz Alternating Current (AC) and the future direct current (DC), zonal electrical distribution ...

Tidd, Chad N. (Chad Norman)

2010-01-01T23:59:59.000Z

109

Light-weight DC to very high voltage DC converter  

DOE Patents [OSTI]

A DC-DC converter capable of generating outputs of 100 KV without a transformer comprises a silicon opening switch (SOS) diode connected to allow a charging current from a capacitor to flow into an inductor. When a specified amount of charge has flowed through the SOS diode, it opens up abruptly; and the consequential collapsing field of the inductor causes a voltage and current reversal that is steered into a load capacitor by an output diode. A switch across the series combination of the capacitor, inductor, and SOS diode closes to periodically reset the SOS diode by inducing a forward-biased current.

Druce, Robert L. (Union City, CA); Kirbie, Hugh C. (Dublin, CA); Newton, Mark A. (Livermore, CA)

1998-01-01T23:59:59.000Z

110

Light-weight DC to very high voltage DC converter  

DOE Patents [OSTI]

A DC-DC converter capable of generating outputs of 100 KV without a transformer comprises a silicon opening switch (SOS) diode connected to allow a charging current from a capacitor to flow into an inductor. When a specified amount of charge has flowed through the SOS diode, it opens up abruptly; and the consequential collapsing field of the inductor causes a voltage and current reversal that is steered into a load capacitor by an output diode. A switch across the series combination of the capacitor, inductor, and SOS diode closes to periodically reset the SOS diode by inducing a forward-biased current. 1 fig.

Druce, R.L.; Kirbie, H.C.; Newton, M.A.

1998-06-30T23:59:59.000Z

111

Monitoring the magnetic field in houses under 50 Hz high-voltage overhead transmission lines  

Science Journals Connector (OSTI)

This paper deals with a one-week monitoring of the 50 Hz magnetic field on the ground floor and the first floor of houses under 150, 220 and 380 kV high-voltage overhead three-phase AC transmission lines. The field strength varied with the current intensity, the conductor height, and the storey of the house. Because current intensity varies with time the magnetic field depended on the time of day and the day of the week. The recorded magnetic field ranged from 0.1 µT to 4.5 µT. The maximum value was at least 20 times weaker than the 100 µT exposure level recommended by the guidelines of the International Radiation Protection Association (IRPA) and about 140 times smaller than the 640 µT of the European Prestandard (CENELEC). The B-field was, for 99.9% of the measuring time, larger than the 0.2 µT cut-off point used to define categories of exposed and unexposed subjects in EMF epidemiological studies and, for 99.3% of the time, was greater than the 0.3 µT level used by US private engineering companies as the 'prudent avoidance' exposure limit. The weakest average magnetic field was at least 40 times larger than the 0.02 µT background value.

G. Decat; J. Van Tongerloo

1998-01-01T23:59:59.000Z

112

Generalized charge simulation method for the calculation of the electric field in high voltage substations  

Science Journals Connector (OSTI)

This paper deals with the calculation of the electric field strength in high voltage (HV) substations comprising complex geometrical structures. Generalized charge simulation ... is to examine the influence of to...

Aleksandar Rankovi?; Milan S. Savi?

2010-07-01T23:59:59.000Z

113

Vehicle Technologies Office Merit Review 2014: High-Voltage Solid Polymer Batteries for Electric Drive Vehicles  

Broader source: Energy.gov [DOE]

Presentation given by Seeo, Inc. at 2014 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Office Annual Merit Review and Peer Evaluation Meeting about high-voltage solid polymer...

114

Optical High Voltage Sensor with Oil- and Gas-free Insulation  

Science Journals Connector (OSTI)

We present an electro-optic high voltage sensor with novel oil- and gas-free insulation based on capacitive electric field steering. The sensor's accuracy is within ±0.2% in a...

Marchese, Sergio V; Wildermuth, Stephan; Steiger, Olivier; Pascal, Joris; Bohnert, Klaus; Eriksson, Göran; Czyzewski, Jan

115

Design of the Wireless Temperature Measurement Alarming System in the High-Voltage Transformer Substation  

Science Journals Connector (OSTI)

Due to electric power overload and equipment aging, fire and explosion occur at transmission circuitry joints in high-voltage transformer substation caused by high temperatures accumulated at these...

Qiang Gao; Hongli Wang; Huaxiang Wang

2008-01-01T23:59:59.000Z

116

Low Cost SiOx-Graphite and High Voltage Spinel Cathode | Department...  

Office of Environmental Management (EM)

Cathode Low Cost SiOx-Graphite and High Voltage Spinel Cathode 2011 DOE Hydrogen and Fuel Cells Program, and Vehicle Technologies Program Annual Merit Review and Peer Evaluation...

117

Electrochemical synthesis of nanosized hydroxyapatite by pulsed direct current method  

SciTech Connect (OSTI)

Synthesis of nanosized of hydroxyapatite (HA) by electrochemical pulsed direct current (PDC) method has been studied. The aim of this work is to study the influence of various PDC parameters (pH initial, electrode distance, duty cycle, frequency, and amplitude) on particle surface area of HA powders. The electrochemical synthesis was prepared in solution Ca{sup 2+}/EDTA{sup 4?}/PO{sub 4}{sup 3+} at concentration 0.25/0.25/0.15 M for 24 h. The electrochemical cell was consisted of two carbon rectangular electrodes connected to a function generator to produce PDC. There were two treatments for particles after electrosynthesized, namely without aging and aged for 2 days at 40 °C. For both cases, the particles were filtered and washed by demineralized water to eliminate the impurities and unreacted reactants. Then, the particles were dried at 100 °C for 2 days. The dried particles were characterized by X-ray diffraction, surface area analyzer, scanning electron microscopy (SEM), Fourier transform infrared spectra and thermogravimetric and differential thermal analysis. HA particles can be produced when the initial pH > 6. The aging process has significant effect on the produced HA particles. SEM images of HA particles showed that the powders consisted of agglomerates composed of fine crystallites and have morphology plate-like and sphere. The surface area of HA particles is in the range of 25 – 91 m{sup 2}/g. The largest particle surface area of HA was produced at 4 cm electrode distance, 80% cycle duty, frequency 0.1 Hz, amplitude 9 V and with aging process.

Nur, Adrian; Rahmawati, Alifah; Ilmi, Noor Izzati; Affandi, Samsudin; Widjaja, Arief [Departement of Chemical Engineering, Faculty of Industrial Technology, Sepuluh Nopember Institute of Technology, Kampus ITS Sukolilo, Surabaya 60111 (Indonesia)

2014-02-24T23:59:59.000Z

118

Cermet insert high voltage holdoff improvement for ceramic/metal vacuum devices  

DOE Patents [OSTI]

An improved metal-to-ceramic seal is provided wherein the ceramic body of the seal contains an integral region of cermet material in electrical contact with the metallic member, e.g., an electrode, of the seal. The seal is useful in high voltage vacuum devices, e.g., vacuum switches, and increases the high-voltage holdoff capabilities of such devices. A method of fabricating such seals is also provided.

Ierna, W.F.

1986-03-11T23:59:59.000Z

119

Princeton Power Systems (TRL 5 6 Component)- Marine High-Voltage Power Conditioning and Transmission System with Integrated Energy Storage  

Broader source: Energy.gov [DOE]

Princeton Power Systems (TRL 5 6 Component) - Marine High-Voltage Power Conditioning and Transmission System with Integrated Energy Storage

120

Students' understanding of direct current resistive electrical circuits Paula Vetter Engelhardta)  

E-Print Network [OSTI]

Students' understanding of direct current resistive electrical circuits Paula Vetter Engelhardta regarding direct current resistive electric circuits often differ from the accepted explanations. At present of direct cur- rent DC resistive electric circuits concepts. DIRECT has been designed for use with high

Zollman, Dean

Note: This page contains sample records for the topic "high-voltage direct current" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

High voltage dc--dc converter with dynamic voltage regulation and decoupling during load-generated arcs  

DOE Patents [OSTI]

A high-power power supply produces a controllable, constant high voltage output under varying and arcing loads. The power supply includes a voltage regulator, an inductor, an inverter for producing a high frequency square wave current of alternating polarity, an improved inverter voltage clamping circuit, a step up transformer, an output rectifier for producing a dc voltage at the output of each module, and a current sensor for sensing output current. The power supply also provides dynamic response to varying loads by controlling the voltage regulator duty cycle and circuitry is provided for sensing incipient arc currents at the output of the power supply to simultaneously decouple the power supply circuitry from the arcing load. The power supply includes a plurality of discrete switching type dc--dc converter modules. 5 Figs.

Shimer, D.W.; Lange, A.C.

1995-05-23T23:59:59.000Z

122

High voltage dc-dc converter with dynamic voltage regulation and decoupling during load-generated arcs  

DOE Patents [OSTI]

A high-power power supply produces a controllable, constant high voltage output under varying and arcing loads. The power supply includes a voltage regulator, an inductor, an inverter for producing a high frequency square wave current of alternating polarity, an improved inverter voltage clamping circuit, a step up transformer, an output rectifier for producing a dc voltage at the output of each module, and a current sensor for sensing output current. The power supply also provides dynamic response to varying loads by controlling the voltage regulator duty cycle and circuitry is provided for sensing incipient arc currents at the output of the power supply to simultaneously decouple the power supply circuitry from the arcing load. The power supply includes a plurality of discrete switching type dc--dc converter modules.

Shimer, Daniel W. (Danville, CA); Lange, Arnold C. (Livermore, CA)

1995-01-01T23:59:59.000Z

123

Mechanisms of deflagration-to-detonation transition under initiation by high-voltage nanosecond discharges  

SciTech Connect (OSTI)

An experimental study of detonation initiation in a stoichiometric propane-oxygen mixture by a high-voltage nanosecond gas discharge was performed in a detonation tube with a single-cell discharge chamber. The discharge study performed in this geometry showed that three modes of discharge development were realized under the experimental conditions: a spark mode with high-temperature channel formation, a streamer mode with nonuniform gas excitation, and a transient mode. Under spark and transient initiation, simultaneous ignition inside the discharge channel occurred, forming a shock wave and leading to a conventional deflagration-to-detonation transition (DDT) via an adiabatic explosion. The DDT length and time at 1 bar of initial pressure in the square smooth tube with a 20-mm transverse size amounted to 50 mm and 50{mu}s, respectively. The streamer mode of discharge development at an initial pressure of 1 bar resulted in nonuniform mixture excitation and a successful DDT via a gradient mechanism, which was confirmed by high-speed time resolved ICCD imaging. The gradient mechanism implied a longer DDT time of 150{mu}s, a DDT run-up distance of 50 mm, and an initiation energy of 1 J, which is two orders of magnitude less than the direct initiation energy for a planar detonation under these conditions. (author)

Rakitin, Aleksandr E.; Starikovskii, Andrei Yu. [Physics of Nonequilibrium Systems Lab, Moscow Institute of Physics and Technology, 9 Institutski Lane, Dolgoprudny 141700 (Russian Federation)

2008-10-15T23:59:59.000Z

124

Apparatuses and method for converting electromagnetic radiation to direct current  

DOE Patents [OSTI]

An energy conversion device may include a first antenna and a second antenna configured to generate an AC current responsive to incident radiation, at least one stripline, and a rectifier coupled with the at least one stripline along a length of the at least one stripline. An energy conversion device may also include an array of nanoantennas configured to generate an AC current in response to receiving incident radiation. Each nanoantenna of the array includes a pair of resonant elements, and a shared rectifier operably coupled to the pair of resonant elements, the shared rectifier configured to convert the AC current to a DC current. The energy conversion device may further include a bus structure operably coupled with the array of nanoantennas and configured to receive the DC current from the array of nanoantennas and transmit the DC current away from the array of nanoantennas.

Kotter, Dale K; Novack, Steven D

2014-09-30T23:59:59.000Z

125

Monte Carlo method for estimating backflashover rates on high voltage transmission lines  

Science Journals Connector (OSTI)

Abstract This paper presents a novel Monte-Carlo based model for the analysis of backflashover rate (BFOR) on high voltage transmission lines. The proposed model aims to take into the account following aspects of the BFOR phenomenon: transmission line (TL) route keraunic level(s), statistical depiction of lightning-current parameters (including statistical correlation), electrogeometric model of lightning attachment, frequency-dependence of TL parameters and electromagnetic coupling effects, tower geometry and surge impedance, tower grounding impulse impedance (with soil ionization), lightning-surge reflections from adjacent towers, non-linearity of the insulator strings flashover characteristic, distribution of lightning strokes along the TL span and power frequency voltage. In the analysis of the BFOR, special attention is given to the influences emanating from the insulator strings flashover characteristic and lightning statistics. The model could be applied to the transmission line as a whole or some of its portions, e.g. first several towers emanating from the substation or several towers crossing a mountain ridge.

Petar Sarajcev

2015-01-01T23:59:59.000Z

126

Lightning strikes to tall objects: Currents inferred from far electromagnetic fields versus directly measured currents  

E-Print Network [OSTI]

-field-to-current conversion factors for lightning strikes to tall objects for (1) the initial peak current at the object top. These far-field-to-current conversion factors are needed for proper interpretation of peak currents reported-field-to-current conversion factor for lightning strikes to flat ground based on the transmission line model and (b

Florida, University of

127

Dual design resistor for high voltage conditioning and transmission lines  

DOE Patents [OSTI]

A dual resistor for eliminating the requirement for two different value resistors. The dual resistor includes a conditioning resistor at a high resistance value and a run resistor at a low resistance value. The run resistor can travel inside the conditioning resistor. The run resistor is capable of being advanced by a drive assembly until an electrical path is completed through the run resistor thereby shorting out the conditioning resistor and allowing the lower resistance run resistor to take over as the current carrier.

Siggins, Timothy Lynn (Newport News, VA); Murray, Charles W. (Hayes, VA); Walker, Richard L. (Norfolk, VA)

2007-01-23T23:59:59.000Z

128

Direct Laser Cladding , Current Status and Future Scope of Application  

Science Journals Connector (OSTI)

During the last decades Direct Laser Cladding has become an established technique in many ... oil drilling components. Continuous wave (CW) lasers with a power up to 18 kW ... with three or more axes, enabling ...

A. Weisheit; A. Gasser; G. Backes; T. Jambor…

2013-01-01T23:59:59.000Z

129

Direct current sputtering of boron from boron/boron mixtures  

DOE Patents [OSTI]

A method for coating a substrate with boron by sputtering includes lowering the electrical resistance of a boron-containing rod to allow electrical conduction in the rod; placing the boron-containing rod inside a vacuum chamber containing substrate material to be coated; applying an electrical potential between the boron target material and the vacuum chamber; countering a current avalanche that commences when the conduction heating rate exceeds the cooling rate, and until a steady equilibrium heating current is reached; and, coating the substrate material with boron by sputtering from the boron-containing rod. 2 figures.

Timberlake, J.R.; Manos, D.; Nartowitz, E.

1994-12-13T23:59:59.000Z

130

HVDC Connected Offshore Wind Power Plants: Review and Outlook of Current Research  

E-Print Network [OSTI]

HVDC Connected Offshore Wind Power Plants: Review and Outlook of Current Research Jakob Glasdam-of-the-art review on grid integration of large offshore wind power plants (OWPPs) using high voltage direct voltage is to acquire in- depth knowledge of relevant operating phenomena in the offshore OWPP grid, rich with power

Bak, Claus Leth

131

Geomagnetically induced currents in the Uruguayan high-voltage power grid  

Science Journals Connector (OSTI)

......and uniform electric fields. IEEE Trans. Power Del. (1998) 13(4):1303-1308. Corbo...Geomagnetic disturbances and impacts upon power system operation. The Electric Power Engineering Handbook-Grigsby L.L., ed. (2007) 2nd edn......

R. Caraballo; L. Sánchez Bettucci; G. Tancredi

2013-01-01T23:59:59.000Z

132

Integrated polymer solar cells in serial architecture with patterned charge-transporting MoOx for miniature high-voltage sources  

Science Journals Connector (OSTI)

We develop miniature high-voltage sources from polymer solar cells (PSCs) with charge-transporting molybdenum oxide (MoOx) integrated in a serial architecture through sacrificial layer (SL)-assisted patterning. The MoOx layer, being patterned by the lift-off process of the SL of a hydrophobic fluorinated-polymer, as a hole transporting layer plays a critical role on the reduction of the dark current and the increase of a high open circuit voltage of an integrated PSC array. The underlying mechanism lies primarily on the elimination of the lateral charge pathways in the MoOx layer in the presence of the electrode interconnection. Two miniature voltage sources consisting of 20 PSCs and 50 PSCs are demonstrated in the operation of a liquid crystal display and an organic field-effect transistor, respectively. Our SL-assisted integration approach will be directly applicable for implementing the self-power sources made of the PSCs into a wide range of the electronic and optoelectronic devices.

Seong-Min Cho; Chang-Min Keum; Hea-Lim Park; Min-Hoi Kim; Jin-Hyuk Bae; Sin-Doo Lee

2014-01-01T23:59:59.000Z

133

Current LDRD Schedule, Laboratory Directed Research and Development (LDRD)  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Homepage BNL Home Homepage BNL Home BNL: Departments | Science | ESS&H | Newsroom | Administration | Visitors | Directory search Go Find People Site Details LDRD Home Current Schedule Proposal Submission Subject Area DOE Order O413.2B DOE-SC Roles & Responsibilities Guidance dated 6/13/06 (pdf) LDRD Reports (PDFs) View Reports Other Information BNL Site Index Can't View PDFs? LDRD Schedule for Fiscal Year 2013 October 1, 2012 FY 2013 Approval of Funding Ceiling from DOE - SC October 1 FY 2013 Individual Project Approvals by DOE - BHSO October 15 Call for FY2012 Individual Project Annual Reports October 31 Information Due to the OMBE/CFO Database November 15 Complex-wide Data from HQ Due to Congress November 20 FY 2012 Individual Project Annual Reports Due

134

International Symposium on High Voltage Engineering, London, August 1999 page 1 of 4  

E-Print Network [OSTI]

substations (GIS) are described. Calculated transfer functions are presented, showing that transverse electric) in gas insulated substations (GIS) has been described in detail previously [1]. In this paper, we present that occurs somewhere in the insulating region between the high voltage (HV) conductor and the metal cladding

Judd, Martin

135

Study of the electric field generated by the high voltage substations  

Science Journals Connector (OSTI)

The paper outlines the results of a study regarding the electromagnetic field generated by a 400 kV high voltage (HV) substation belonging to the Romanian national Power Grid Company Transelectrica SA. In the first part of the paper, a semi-analytical ... Keywords: HV substations, computation, electromagnetic field, human exposure, limits

Calin Munteanu; Vasile Topa; Marius Purcar; Laura Grindei; Adina Racasan

2010-10-01T23:59:59.000Z

136

Electro-optic imagery of high-voltage GaAs photoconductive switches  

SciTech Connect (OSTI)

The authors present electro-optic images of GaAs high-voltage photoconductive switches utilizing the electro-optic effect of the semi-insulating GaAs substrate. Experimental methodology for obtaining the images is described along with a self-calibrating data reduction algorithm. Use of the technique for observing fabrication defects is shown.

Falk, R.A.; Adams, J.C.; Capps, C.D.; Ferrier, S.G.; Krinsky, J.A. (Boeing Defense and Space Group, Seattle, WA (United States))

1995-01-01T23:59:59.000Z

137

An earth-isolated optically coupled wideband high voltage probe powered by ambient light  

E-Print Network [OSTI]

(2012) Optimized working conditions for a thermoelectric generator as a topping cycle for gas turbines J (2012) Feasibility study in application of forging waste heat on absorption cooling system J. Renewable-emitting diode that converts high voltage into an amplitude-modulated optical signal, which is then conveyed

Bellan, Paul M.

138

Public Opinions of Building Additional High-Voltage Electric Power Lines  

E-Print Network [OSTI]

to build new power lines. Residents living in counties with planned routes for new transmission linesPublic Opinions of Building Additional High-Voltage Electric Power Lines A Report to the National-Voltage Electric Power Lines: A Report to the National Science Foundation and the Electric Power Research Center

Tesfatsion, Leigh

139

Performance Analysis of a Hybrid Asymmetric Multilevel Inverter for High Voltage Active Power Filter Applications  

E-Print Network [OSTI]

Performance Analysis of a Hybrid Asymmetric Multilevel Inverter for High Voltage Active Power voltage-source inverters connected in series (known as cascaded hybrid asymmetric multilevel inverter voltage application due to semiconductor constraint. In order to achieve higher power level, hybrid

Catholic University of Chile (Universidad Católica de Chile)

140

Propagation direction reversal of ionization zones in the transition between high and low current magnetron sputtering  

SciTech Connect (OSTI)

Past research has revealed the propagation of dense, asymmetric ionization zones in both high and low current magnetron discharges. Here we report about the direction reversal of ionization zone propagation as observed with fast cameras. At high currents, zones move in the E B direction with velocities of 103 to 104 m/s. However at lower currents, ionization zones are observed to move in the opposite, the -E B direction, with velocities ~;; 103 m/s. It is proposed that the direction reversal is associated with the local balance of ionization and supply of neutrals in the ionization zone.

School of Materials Science and Engineering, State Key Lab for Materials Processing and Die & Mold Technology, Huazhong University of Science and Technology, Wuhan 430074, China; Department of Physics, University of California Berkeley, Berkeley, California 94720, USA; Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, California 94720, USA; Yang, Yuchen; Liu, Jason; Liu, Lin; Anders, André

2014-12-11T23:59:59.000Z

Note: This page contains sample records for the topic "high-voltage direct current" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Direct-Current Resistivity Survey At Cove Fort Area - Vapor (Warpinski, Et  

Open Energy Info (EERE)

Direct-Current Resistivity Survey At Cove Fort Area - Vapor (Warpinski, Et Direct-Current Resistivity Survey At Cove Fort Area - Vapor (Warpinski, Et Al., 2004) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Cove Fort Area (Warpinski, Et Al., 2004) Exploration Activity Details Location Cove Fort Geothermal Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes Update to Warpinski, et al., 2002 References N. R. Warpinski, A. R. Sattler, R. Fortuna, D. A. Sanchez, J. Nathwani (2004) Geothermal Resource Exploration And Definition Projects Retrieved from "http://en.openei.org/w/index.php?title=Direct-Current_Resistivity_Survey_At_Cove_Fort_Area_-_Vapor_(Warpinski,_Et_Al.,_2004)&oldid=598134"

142

Direct-Current Resistivity At Cove Fort Area - Liquid (Warpinski, Et Al.,  

Open Energy Info (EERE)

Direct-Current Resistivity At Cove Fort Area - Liquid (Warpinski, Et Al., Direct-Current Resistivity At Cove Fort Area - Liquid (Warpinski, Et Al., 2004) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity At Cove Fort Area (Warpinski, Et Al., 2004) Exploration Activity Details Location Cove Fort Geothermal Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes Update to Warpinski, et al., 2002 References N. R. Warpinski, A. R. Sattler, R. Fortuna, D. A. Sanchez, J. Nathwani (2004) Geothermal Resource Exploration And Definition Projects Retrieved from "http://en.openei.org/w/index.php?title=Direct-Current_Resistivity_At_Cove_Fort_Area_-_Liquid_(Warpinski,_Et_Al.,_2004)&oldid=598125" Categories: Exploration Activities

143

Direct-Current Resistivity Survey At Marysville Mt Area (Blackwell) | Open  

Open Energy Info (EERE)

Direct-Current Resistivity Survey At Marysville Mt Area (Blackwell) Direct-Current Resistivity Survey At Marysville Mt Area (Blackwell) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Marysville Mt Area (Blackwell) Exploration Activity Details Location Marysville Mt Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness not indicated DOE-funding Unknown Notes A dipole-dipole resistivity survey of the area was carried out with estimated penetration up to 700 meters and no indication of low values of resistivity were found associated with the thermal anomaly. References D. D. Blackwell (Unknown) Exploration In A Blind Geothermal Area Near Marysville, Montana, Usa Retrieved from "http://en.openei.org/w/index.php?title=Direct-Current_Resistivity_Survey_At_Marysville_Mt_Area_(Blackwell)&oldid=510539

144

Direct-Current Resistivity Survey At Roosevelt Hot Springs Area (Combs  

Open Energy Info (EERE)

Direct-Current Resistivity Survey At Roosevelt Hot Springs Area (Combs Direct-Current Resistivity Survey At Roosevelt Hot Springs Area (Combs 2006) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Roosevelt Hot Springs Area (Combs 2006) Exploration Activity Details Location Roosevelt Hot Springs Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness not indicated DOE-funding Unknown Notes "SP, MT, dipole-dipole resistivity, CSAMT; sufficient electrical data may be available" References Jim Combs (1 January 2006) Historical Exploration And Drilling Data From Geothermal Prospects And Power Generation Projects In The Western United States Retrieved from "http://en.openei.org/w/index.php?title=Direct-Current_Resistivity_Survey_At_Roosevelt_Hot_Springs_Area_(Combs_2006)&oldid=510548"

145

Direct-Current Resistivity At Cove Fort Area - Liquid (Combs 2006) | Open  

Open Energy Info (EERE)

Direct-Current Resistivity At Cove Fort Area - Liquid (Combs 2006) Direct-Current Resistivity At Cove Fort Area - Liquid (Combs 2006) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity At Cove Fort Area (Combs 2006) Exploration Activity Details Location Cove Fort Geothermal Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness not indicated DOE-funding Unknown Notes "SP, dipole-dipole resistivity, CSAMT; sufficient electrical data are available. Reservoir model?" References Jim Combs (1 January 2006) Historical Exploration And Drilling Data From Geothermal Prospects And Power Generation Projects In The Western United States Retrieved from "http://en.openei.org/w/index.php?title=Direct-Current_Resistivity_At_Cove_Fort_Area_-_Liquid_(Combs_2006)&oldid=598123

146

Direct-Current Resistivity At Brady Hot Springs Area (Combs 2006) | Open  

Open Energy Info (EERE)

Direct-Current Resistivity At Brady Hot Springs Area (Combs 2006) Direct-Current Resistivity At Brady Hot Springs Area (Combs 2006) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity At Brady Hot Springs Area (Combs 2006) Exploration Activity Details Location Brady Hot Springs Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness not indicated DOE-funding Unknown Notes "sufficient geophysical data are not available" References Jim Combs (1 January 2006) Historical Exploration And Drilling Data From Geothermal Prospects And Power Generation Projects In The Western United States Retrieved from "http://en.openei.org/w/index.php?title=Direct-Current_Resistivity_At_Brady_Hot_Springs_Area_(Combs_2006)&oldid=594379"

147

Monolithically interconnected GaAs solar cells: A new interconnection technology for high voltage solar cell output  

SciTech Connect (OSTI)

Photovoltaic linear concentrator arrays can benefit from high performance solar cell technologies being developed at AstroPower. Specifically, these are the integration of thin GaAs solar cell and epitaxial lateral overgrowth technologies with the application of monolithically interconnected solar cell (MISC) techniques. This MISC array has several advantages which make it ideal for space concentrator systems. These are high system voltage, reliable low cost monolithically formed interconnections, design flexibility, costs that are independent of array voltage, and low power loss from shorts, opens, and impact damage. This concentrator solar cell will incorporate the benefits of light trapping by growing the device active layers over a low-cost, simple, PECVD deposited silicon/silicon dioxide Bragg reflector. The high voltage-low current output results in minimal 12R losses while properly designing the device allows for minimal shading and resistance losses. It is possible to obtain open circuit voltages as high as 67 volts/cm of solar cell length with existing technology. The projected power density for the high performance device is 5 kW/m for an AMO efficiency of 26% at 1 5X. Concentrator solar cell arrays are necessary to meet the power requirements of specific mission platforms and can supply high voltage power for electric propulsion systems. It is anticipated that the high efficiency, GaAs monolithically interconnected linear concentrator solar cell array will enjoy widespread application for space based solar power needs. Additional applications include remote man-portable or ultra-light unmanned air vehicle (UAV) power supplies where high power per area, high radiation hardness and a high bus voltage or low bus current are important. The monolithic approach has a number of inherent advantages, including reduced cost per interconnect and increased reliability of array connections. There is also a high potential for a large number of consumer products.

Dinetta, L.C.; Hannon, M.H.

1995-10-01T23:59:59.000Z

148

Direct-Current Resistivity Survey At Hualalai Northwest Rift Area (Thomas,  

Open Energy Info (EERE)

Hualalai Northwest Rift Area (Thomas, Hualalai Northwest Rift Area (Thomas, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Hualalai Northwest Rift Area (Thomas, 1986) Exploration Activity Details Location Hualalai Northwest Rift Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness not indicated DOE-funding Unknown Notes A total of seven Schlumberger soundings were performed on Hualalai. References Donald M. Thomas (1 January 1986) Geothermal Resources Assessment In Hawaii Retrieved from "http://en.openei.org/w/index.php?title=Direct-Current_Resistivity_Survey_At_Hualalai_Northwest_Rift_Area_(Thomas,_1986)&oldid=510528" Category: Exploration Activities What links here Related changes

149

Direct-Current Resistivity Survey At Cove Fort Area - Liquid (Combs 2006) |  

Open Energy Info (EERE)

- Liquid (Combs 2006) - Liquid (Combs 2006) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Cove Fort Area (Combs 2006) Exploration Activity Details Location Cove Fort Geothermal Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness not indicated DOE-funding Unknown Notes "SP, dipole-dipole resistivity, CSAMT; sufficient electrical data are available. Reservoir model?" References Jim Combs (1 January 2006) Historical Exploration And Drilling Data From Geothermal Prospects And Power Generation Projects In The Western United States Retrieved from "http://en.openei.org/w/index.php?title=Direct-Current_Resistivity_Survey_At_Cove_Fort_Area_-_Liquid_(Combs_2006)&oldid=598127"

150

Radio-Frequency Interference (RFI) From Extra-High-Voltage (EHV) Transmission Lines  

E-Print Network [OSTI]

discharges are a design issue. Extra-high-voltage (EHV) transmission lines have operating voltages of 345 kV building a 345-kV transmission line from Red Hill, NM to Deming, NM which would run east along US60 to its with respect to radio noise: (1) lines with voltages below 70 kV and (2) lines with voltages above 110 kV

Ellingson, Steven W.

151

Round-robin artificial contamination test on high voltage dc insulators  

SciTech Connect (OSTI)

This paper summarizes the results of a worldwide round-robin test of high voltage dc (HVDC) insulators, which was carried out in six laboratories aiming at standardization of the method for artificial contamination tests on HVDC insulators. Flashover characteristics of three kinds of specimens were evaluated by the clean fog and the salt fog procedures. Sufficient information is now available to allow the preparation of provisional international specifications for artificial contamination testing of HVDC insulators.

Naito, K.; Schneider, H.M.

1995-07-01T23:59:59.000Z

152

Direct-Current Resistivity At Cove Fort Area (Warpinski, Et Al., 2002) |  

Open Energy Info (EERE)

(Redirected from Direct-Current Resistivity At Cove Fort Area - Vapor (Redirected from Direct-Current Resistivity At Cove Fort Area - Vapor (Warpinski, Et Al., 2002)) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity At Cove Fort Area (Warpinski, Et Al., 2002) Exploration Activity Details Location Cove Fort Geothermal Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes The project at Cove Fort/Sulphurdale in Utah, T26S R6/7W, is concerned with locating and drilling a 900-meter well to explore the western extension of the Cove Fort-Sulphurdale geothermal area. The geophysical exploration consisted of resistivity, ground magnetic, and microgravity surveys that were made to site the well in an optimum location.

153

Direct-Current Resistivity Survey At Lightning Dock Area (Cunniff & Bowers,  

Open Energy Info (EERE)

Direct-Current Resistivity Survey At Lightning Dock Area (Cunniff & Bowers, Direct-Current Resistivity Survey At Lightning Dock Area (Cunniff & Bowers, 2005) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Lightning Dock Area (Cunniff & Bowers, 2005) Exploration Activity Details Location Lightning Dock Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness not indicated DOE-funding Unknown Notes Two electrical resistivity survey lines were run in the project area: a southern east-west line along Caliche Road, and a northern east-west line in the south half Section 6, T25S, R19W (figure 5). The Caliche Road line is located south of the greenhouse complex and was run along the road, which was also used for a gravity traverse. The northern line, named

154

Direct-Current Resistivity Survey At Coso Geothermal Area (1977) | Open  

Open Energy Info (EERE)

Direct-Current Resistivity Survey At Coso Geothermal Area (1977) Direct-Current Resistivity Survey At Coso Geothermal Area (1977) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Coso Geothermal Area (1977) Exploration Activity Details Location Coso Geothermal Area Exploration Technique Direct-Current Resistivity Survey Activity Date 1977 Usefulness useful regional reconnaissance DOE-funding Unknown Exploration Basis To investigate electrical properties of rocks associated with thermal phenomena of the Devil's Kitchen-Coso Hot Springs area Notes DC resistivity geophysical surveys determined that the secondary low in the geothermal area, best defined by the 7.5-Hz AMT map and dc soundings, is caused by a shallow conductive zone (5--30 ohm m) interpreted to be

155

EIS-0450: TransWest Express 600 kV Direct Current Transmission Project in  

Broader source: Energy.gov (indexed) [DOE]

0: TransWest Express 600 kV Direct Current Transmission 0: TransWest Express 600 kV Direct Current Transmission Project in Wyoming, Colorado, Utah, and Nevada EIS-0450: TransWest Express 600 kV Direct Current Transmission Project in Wyoming, Colorado, Utah, and Nevada Summary This EIS, being prepared jointly by DOE's Western Area Power Administration and the Department of the Interior's Bureau of Land Management (Wyoming State Office), evaluates the environmental impacts of granting a right-of-way for the TransWest Express 600-kilovolt Direct Current Transmission Project and amending a land use plan. The project consists of an overhead transmission line that would extend approximately 725 miles from south-central Wyoming, through Colorado and Utah. Western proposes to be a joint owner of the project. Public Comment Opportunities

156

Direct-Current Resistivity Survey At Kilauea Southwest Rift And South Flank  

Open Energy Info (EERE)

Direct-Current Resistivity Survey At Kilauea Southwest Rift And South Flank Direct-Current Resistivity Survey At Kilauea Southwest Rift And South Flank Area (Thomas, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Kilauea Southwest Rift And South Flank Area (Thomas, 1986) Exploration Activity Details Location Kilauea Southwest Rift And South Flank Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes The electrical resistivity data acquired on the southwest rift delineated two distinct basement resistivity structures northwest of the rift zone: a high-resistivity basement at approximately 60 m a.s.l, and located north of a prehistoric fissure, and a low-resistivity deep basement (20 m a.s.1.) to

157

Direct-Current Resistivity Survey At Cove Fort Area - Vapor (Warpinski, Et  

Open Energy Info (EERE)

Direct-Current Resistivity Survey At Cove Fort Area - Vapor (Warpinski, Et Direct-Current Resistivity Survey At Cove Fort Area - Vapor (Warpinski, Et Al., 2002) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Cove Fort Area (Warpinski, Et Al., 2002) Exploration Activity Details Location Cove Fort Geothermal Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes The project at Cove Fort/Sulphurdale in Utah, T26S R6/7W, is concerned with locating and drilling a 900-meter well to explore the western extension of the Cove Fort-Sulphurdale geothermal area. The geophysical exploration consisted of resistivity, ground magnetic, and microgravity surveys that were made to site the well in an optimum location.

158

Direct-Current Resistivity At Kilauea Southwest Rift And South Flank Area  

Open Energy Info (EERE)

Direct-Current Resistivity At Kilauea Southwest Rift And South Flank Area Direct-Current Resistivity At Kilauea Southwest Rift And South Flank Area (Thomas, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity At Kilauea Southwest Rift And South Flank Area (Thomas, 1986) Exploration Activity Details Location Kilauea Southwest Rift And South Flank Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes The electrical resistivity data acquired on the southwest rift delineated two distinct basement resistivity structures northwest of the rift zone: a high-resistivity basement at approximately 60 m a.s.l, and located north of a prehistoric fissure, and a low-resistivity deep basement (20 m a.s.1.) to the south and east of this fissure (Figs 48, 49). These data suggest that a

159

Direct-Current Resistivity At Cove Fort Area (Warpinski, Et Al., 2002) |  

Open Energy Info (EERE)

Direct-Current Resistivity At Cove Fort Area (Warpinski, Et Al., 2002) Direct-Current Resistivity At Cove Fort Area (Warpinski, Et Al., 2002) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity At Cove Fort Area (Warpinski, Et Al., 2002) Exploration Activity Details Location Cove Fort Geothermal Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes The project at Cove Fort/Sulphurdale in Utah, T26S R6/7W, is concerned with locating and drilling a 900-meter well to explore the western extension of the Cove Fort-Sulphurdale geothermal area. The geophysical exploration consisted of resistivity, ground magnetic, and microgravity surveys that were made to site the well in an optimum location. References N. R. Warpinski, A. R. Sattlerl, D. A. Sanchez (2002) Geothermal

160

The Effect of Propane on Atomic Spectrometric Signals in the Direct-Current Plasma  

Science Journals Connector (OSTI)

The addition of small amounts of propane to the direct-current plasma (DCP) affects the emission signal of analyte species in the plasma. In the normal analytical region of the...

McCreary, Terry W; Long, Gary L

1988-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "high-voltage direct current" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Parallel electric fields in the upward current region of the aurora: Indirect and direct observations  

E-Print Network [OSTI]

Parallel electric fields in the upward current region of the aurora: Indirect and direct In this article we present electric field, magnetic field, and charged particle observations from the upward current region of the aurora focusing on the structure of electric fields at the boundary between

California at Berkeley, University of

162

ELSEVIER Bioelectrochemistry and Bioenergetics 35 (1994) 99-101 Low level direct current -cell culture fibroblast model  

E-Print Network [OSTI]

ELSEVIER Bioelectrochemistry and Bioenergetics 35 (1994) 99-101 Low level direct current - cell;100 U. Batista et al. / Bioelectrochemistry and Bioenergetics 35 (1994) 99-101 2.2. Direct current

Ljubljana, University of

163

High-voltage supply for neutron tubes in well-logging applications  

DOE Patents [OSTI]

A high voltage supply is provided for a neutron tube used in well logging. The biased pulse supply of the invention combines DC and full pulse techniques and produces a target voltage comprising a substantial negative DC bias component on which is superimposed a pulse whose negative peak provides the desired negative voltage level for the neutron tube. The target voltage is preferably generated using voltage doubling techniques and employing a voltage source which generates bipolar pulse pairs having an amplitude corresponding to the DC bias level.

Humphreys, D.R.

1982-09-15T23:59:59.000Z

164

A Fusing Switch for Fault Suppression in the SNS High Voltage Converter Modulators  

SciTech Connect (OSTI)

The High Voltage Converter Modulators (HVCMs) at the Spallation Neutron Source (SNS) have operated in excess of a combined 250,000 hours. Performance and reliability improvements to the HVCM are ongoing to increase modulator availability as accelerator system demands increase. There is a relatively large amount of energy storage in the HVCMs, {approx}180 kJ. This energy has the potential to dump into unsuppressed faults, cause damage, and increase the time to repair. The 'fusing switch' concept involves isolation of this stored energy from the location of the most common faults. This paper introduces this concept and its application to the HVCMs.

Kemp, Mark A.; Burkhart, Craig; Nguyen, Minh N.; /SLAC; Anderson, David E.; /Oak Ridge

2009-08-03T23:59:59.000Z

165

High voltage power supplies for the neutral beam injectors of the stellarator TJ-II  

Science Journals Connector (OSTI)

Neutral beam injection will be available for the second experimental phase of TJ-II. Two injectors, set in co-counter configuration, will inject into the plasma two 40 keV H0 beams, each of up to 1 MW. The two high voltage power supplies to feed the acceleration grids of the injectors, described in this paper, are of the transformer–rectifier type, taking their primary energy from a pulsed flywheel generator, and are coupled to the acceleration grids through a switching device. This environment effectively sets the main operation limits and protection requirements of the power supplies.

J Alonso; M Liniers; L Mart??nez Laso; E Jauregi; C Luc??a; F Valcárcel

2001-01-01T23:59:59.000Z

166

Influence of energy contributions to a high-voltage atmospheric-pressure discharge on the efficiency of conversion of ethanol  

Science Journals Connector (OSTI)

The results of experimental investigations of the conversion of ethanol in a high-voltage atmospheric-pressure discharge have been presented. The influence of the energy parameters of the discharge on the yield a...

S. A. Zhdanok; A. V. Krauklis; P. P. Samtsov…

2006-11-01T23:59:59.000Z

167

Direct-Current Resistivity Survey At Mt Princeton Hot Springs Area  

Open Energy Info (EERE)

source source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit History Facebook icon Twitter icon » Direct-Current Resistivity Survey At Mt Princeton Hot Springs Area (Richards, Et Al., 2010) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Mt Princeton Hot Springs Area (Richards, Et Al., 2010) Exploration Activity Details Location Mt Princeton Hot Springs Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes Used to map fracture and fluid flow patterns. References K. Richards, A. Revil, A. Jardani, F. Henderson, M. Batzle, A. Haas (2010) Pattern Of Shallow Ground Water Flow At Mount Princeton Hot Springs,

168

Direct-Current Resistivity Survey At Mokapu Penninsula Area (Thomas, 1986)  

Open Energy Info (EERE)

Direct-Current Resistivity Survey At Mokapu Direct-Current Resistivity Survey At Mokapu Penninsula Area (Thomas, 1986) Exploration Activity Details Location Mokapu Penninsula Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness not indicated DOE-funding Unknown Notes Geophysical surveys on Mokapu were restricted to three Schlumberger soundings (Fig. 17). The results of these soundings appeared to indicate a highly resistive surface section underlain by one or more layers of intermediate to low resistivity (Fig. 18). Basement resistivities in all cases were less than 3 ohm.m and were interpreted to correspond to alluvial layers saturated with cold seawater (Lienert, 1982). --- A separate geophysical analysis performed on the Koolau caldera area (Kauahikaua, 1981 a) synthesized existing self-potential, gravity, seismic and aeromagnetic

169

Direct-Current Resistivity At Long Valley Caldera Area (Pribnow, Et Al.,  

Open Energy Info (EERE)

source source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit History Facebook icon Twitter icon » Direct-Current Resistivity At Long Valley Caldera Area (Pribnow, Et Al., 2003) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity At Long Valley Caldera Area (Pribnow, Et Al., 2003) Exploration Activity Details Location Long Valley Caldera Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes DC electrical sounding measurements provide a 2-D image of the resistivity distribution beneath Long Valley Caldera. Conductive zones and SP anomalies correlate with the location of known faults in agreement with previous

170

Direct-Current Resistivity Survey At Dixie Valley Geothermal Field Area  

Open Energy Info (EERE)

Direct-Current Resistivity Survey At Dixie Valley Direct-Current Resistivity Survey At Dixie Valley Geothermal Field Area (Laney, 2005) Exploration Activity Details Location Dixie Valley Geothermal Field Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes Structural Controls, Alteration, Permeability and Thermal Regime of Dixie Valley from New-Generation Mt/Galvanic Array Profiling, Phillip Wannamaker. A new-generation MT/DC array resistivity measurement system was applied at the Dixie Valley thermal area. Basic goals of the survey are 1), resolve a fundamental structural ambiguity at the Dixie Valley thermal area (single rangefront fault versus shallower, stepped pediment; 2), delineate fault zones which have experienced fluid flux as indicated by low resistivity;

171

Direct-Current Resistivity Survey At Kilauea Summit Area (Keller, Et Al.,  

Open Energy Info (EERE)

1979) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Kilauea Summit Area (Keller, Et Al., 1979) Exploration Activity Details Location Kilauea Summit Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes An electromagnetic sounding survey by Jackson and Keller (1972) defined a strong resistivity anomaly above the center of inflation associated with volcanic activity during the early 1960's. References George V. Keller, L. Trowbridge Grose, John C. Murray, Catherine K. Skokan (1979) Results Of An Experimental Drill Hole At The Summit Of Kilauea Volcano, Hawaii Retrieved from "http://en.openei.org/w/index.php?title=Direct-Current_Resistivity_Survey_At_Kilauea_Summit_Area_(Keller,_Et_Al.,_1979)&oldid=510532

172

Direct-Current Resistivity Survey At Cove Fort Area (Warpinski, Et Al.,  

Open Energy Info (EERE)

(Warpinski, Et Al., (Warpinski, Et Al., 2004) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Cove Fort Area (Warpinski, Et Al., 2004) Exploration Activity Details Location Cove Fort Geothermal Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes Update to Warpinski, et al., 2002 References N. R. Warpinski, A. R. Sattler, R. Fortuna, D. A. Sanchez, J. Nathwani (2004) Geothermal Resource Exploration And Definition Projects Retrieved from "http://en.openei.org/w/index.php?title=Direct-Current_Resistivity_Survey_At_Cove_Fort_Area_(Warpinski,_Et_Al.,_2004)&oldid=598126" Categories: Exploration Activities DOE Funded Activities What links here

173

Direct-Current Resistivity At Haleakala Volcano Area (Thomas, 1986) | Open  

Open Energy Info (EERE)

source source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit History Facebook icon Twitter icon » Direct-Current Resistivity At Haleakala Volcano Area (Thomas, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity At Haleakala Volcano Area (Thomas, 1986) Exploration Activity Details Location Haleakala Volcano Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness not indicated DOE-funding Unknown Notes The field survey program on the northwest rift zone consisted of soil mercury and radon emanometry surveys, groundwater temperature and chemistry studies, Schlumberger resistivity soundings and self-potential profiles.

174

Direct-Current Resistivity Survey At Mauna Loa Northeast Rift Area (Thomas,  

Open Energy Info (EERE)

Direct-Current Resistivity Survey At Mauna Loa Direct-Current Resistivity Survey At Mauna Loa Northeast Rift Area (Thomas, 1986) Exploration Activity Details Location Mauna Loa Northeast Rift Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes The vertical electrical sounding surveys encountered few difficulties and were able to resolve basement resistivities in all locations. The resistivity sections derived indicated a 3000- 20,000 ohm.m surface layer underlain by a 500- 900 ohm-m cold freshwatersaturated layer and a basement layer of less than 100 ohm.m (Kauahikaua and Mattice, 1981). The depth of penetration of these soundings was estimated to be about 800 m to 900 m b.s.1. and thus the basement resistivities probably correspond to basalts

175

Direct-Current Resistivity Survey At Clear Lake Area (Skokan, 1993) | Open  

Open Energy Info (EERE)

Area (Skokan, 1993) Area (Skokan, 1993) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Clear Lake Area (Skokan, 1993) Exploration Activity Details Location Clear Lake Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes Several direct-current, bipole-dipole surveys were carried out in the area. These field measurements (Rapolla and Keller, 1984) were combined by spatially averaging apparent resistivities on a one kilometer grid ( Fig. 6 ). The authors felt that local geologic noise could be reduced and large-scale features would be emphasized by this averaging. The most significant feature which resulted was a clear electrical signature of the

176

Direct-Current Resistivity Survey At Nw Basin & Range Region (Pritchett,  

Open Energy Info (EERE)

source source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit History Facebook icon Twitter icon » Direct-Current Resistivity Survey At Nw Basin & Range Region (Pritchett, 2004) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Nw Basin & Range Region (Pritchett, 2004) Exploration Activity Details Location Northwest Basin and Range Geothermal Region Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes NOTE: These are theoretical/computer simulation tests of various methods on eight hypothetical 'model' basing-and-range geothermal systems. "The

177

Direct-Current Resistivity Survey At Haleakala Volcano Area (Thomas, 1986)  

Open Energy Info (EERE)

Direct-Current Resistivity Survey At Haleakala Direct-Current Resistivity Survey At Haleakala Volcano Area (Thomas, 1986) Exploration Activity Details Location Haleakala Volcano Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness not indicated DOE-funding Unknown Notes The field survey program on the northwest rift zone consisted of soil mercury and radon emanometry surveys, groundwater temperature and chemistry studies, Schlumberger resistivity soundings and self-potential profiles. Geophysical and geochemical surveys along this rift (southwest) were limited by difficult field conditions and access limitations. The geophysical program consisted of one Schlumberger sounding, one self-potential profile and one controlled-source electromagnetic sounding. The geochemical data collected included a reconnaissance soil mercury and

178

Direct-Current Resistivity Survey At Long Valley Caldera Area (Pribnow, Et  

Open Energy Info (EERE)

source source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit History Facebook icon Twitter icon » Direct-Current Resistivity Survey At Long Valley Caldera Area (Pribnow, Et Al., 2003) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Long Valley Caldera Area (Pribnow, Et Al., 2003) Exploration Activity Details Location Long Valley Caldera Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes DC electrical sounding measurements provide a 2-D image of the resistivity distribution beneath Long Valley Caldera. Conductive zones and SP anomalies

179

Direct-Current Resistivity At Kilauea Summit Area (Keller, Et Al., 1979) |  

Open Energy Info (EERE)

Summit Area (Keller, Et Al., 1979) Summit Area (Keller, Et Al., 1979) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity At Kilauea Summit Area (Keller, Et Al., 1979) Exploration Activity Details Location Kilauea Summit Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes An electromagnetic sounding survey by Jackson and Keller (1972) defined a strong resistivity anomaly above the center of inflation associated with volcanic activity during the early 1960's. References George V. Keller, L. Trowbridge Grose, John C. Murray, Catherine K. Skokan (1979) Results Of An Experimental Drill Hole At The Summit Of Kilauea Volcano, Hawaii Retrieved from "http://en.openei.org/w/index.php?title=Direct-Current_Resistivity_At_Kilauea_Summit_Area_(Keller,_Et_Al.,_1979)&oldid=594370"

180

Direct-Current Resistivity At Clear Lake Area (Skokan, 1993) | Open Energy  

Open Energy Info (EERE)

Clear Lake Area (Skokan, 1993) Clear Lake Area (Skokan, 1993) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity At Clear Lake Area (Skokan, 1993) Exploration Activity Details Location Clear Lake Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes Several direct-current, bipole-dipole surveys were carried out in the area. These field measurements (Rapolla and Keller, 1984) were combined by spatially averaging apparent resistivities on a one kilometer grid ( Fig. 6 ). The authors felt that local geologic noise could be reduced and large-scale features would be emphasized by this averaging. The most significant feature which resulted was a clear electrical signature of the

Note: This page contains sample records for the topic "high-voltage direct current" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Direct-Current Resistivity Survey At Mauna Loa Southwest Rift Area (Thomas,  

Open Energy Info (EERE)

Area (Thomas, Area (Thomas, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Mauna Loa Southwest Rift Area (Thomas, 1986) Exploration Activity Details Location Mauna Loa Southwest Rift Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness not indicated DOE-funding Unknown Notes Field surveys in the South Point area were limited to a series of Schlumberger soundings and a self-potential traverse across the rift zone. The absence of groundwater wells and time and funding constraints precluded any geochemical field surveys. References Donald M. Thomas (1 January 1986) Geothermal Resources Assessment In Hawaii Retrieved from "http://en.openei.org/w/index.php?title=Direct-Current_Resistivity_Survey_At_Mauna_Loa_Southwest_Rift_Area_(Thomas,_1986)&oldid=510541"

182

Direct-Current Resistivity Survey At Kawaihae Area (Thomas, 1986) | Open  

Open Energy Info (EERE)

source source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit History Facebook icon Twitter icon » Direct-Current Resistivity Survey At Kawaihae Area (Thomas, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Kawaihae Area (Thomas, 1986) Exploration Activity Details Location Kawaihae Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness not indicated DOE-funding Unknown Notes In addition to the aeromagnetic data, the field survey program in Kawaihae included six Schlumberger resistivity soundings between Kawaihae and Waimea (Kauahikaua and Mattice, 1981). The results of these sounding (Fig. 35)

183

Direct-Current Resistivity At Cove Fort Area (Warpinski, Et Al., 2004) |  

Open Energy Info (EERE)

source source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit History Facebook icon Twitter icon » Direct-Current Resistivity At Cove Fort Area (Warpinski, Et Al., 2004) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity At Cove Fort Area (Warpinski, Et Al., 2004) Exploration Activity Details Location Cove Fort Geothermal Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes Update to Warpinski, et al., 2002 References N. R. Warpinski, A. R. Sattler, R. Fortuna, D. A. Sanchez, J. Nathwani (2004) Geothermal Resource Exploration And Definition Projects

184

Temperature rise testing of current transformers: improvement in test method.  

E-Print Network [OSTI]

??The nature of electric power generation, transmission and distribution systems frequently faces high voltages, high currents, or a combination of both. Electric phenomena as well… (more)

Garduno, Hideki

2012-01-01T23:59:59.000Z

185

Direct-Current Resistivity Survey At Lightning Dock Area (Warpinski, Et  

Open Energy Info (EERE)

Et Et Al., 2002) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Lightning Dock Area (Warpinski, Et Al., 2002) Exploration Activity Details Location Lightning Dock Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness not indicated DOE-funding Unknown Notes As a foundation for successful siting and drilling a deep test well, additional geophysical work has been completed including gravity, resistivity, and airborne magnetic surveys. Several new seismic profiles are planned to provide more focused siting and drilling plans. These new geophysical surveys are being integrated into the combined thermal, hydrologic, and subsurface stratigraphic information data sets to provide a

186

Direct-Current Resistivity Survey At Walker-Lane Transitional Zone Region  

Open Energy Info (EERE)

Pritchett, 2004) Pritchett, 2004) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Walker-Lane Transitional Zone Region (Pritchett, 2004) Exploration Activity Details Location Walker-Lane Transition Zone Geothermal Region Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes NOTE: These are theoretical/computer simulation tests of various methods on eight hypothetical 'model' basing-and-range geothermal systems. "The 300-meter heat flow holes are essentially useless for finding the "hidden" reservoirs. Clearly, the best results are obtained from the SP and MT surveys, with DC resistivity a close third. It is concluded that the best

187

Direct-Current Resistivity At Lualualei Valley Area (Thomas, 1986) | Open  

Open Energy Info (EERE)

Lualualei Valley Area (Thomas, 1986) Lualualei Valley Area (Thomas, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity At Lualualei Valley Area (Thomas, 1986) Exploration Activity Details Location Lualualei Valley Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes Three Schlumberger resistivity soundings were performed in Lualualei Valley (Mattice and Kauahikaua, 1979). K840 Interpretation of the resistivity soundings suggests that the source of the warm water layer within the valley was the dense dike complex associated with the ancient magma chamber of Waianae volcano. References Donald M. Thomas (1 January 1986) Geothermal Resources Assessment In Hawaii Retrieved from

188

Direct-Current Resistivity At Lightning Dock Area (Warpinski, Et Al., 2002)  

Open Energy Info (EERE)

2) 2) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity At Lightning Dock Area (Warpinski, Et Al., 2002) Exploration Activity Details Location Lightning Dock Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness not indicated DOE-funding Unknown Notes As a foundation for successful siting and drilling a deep test well, additional geophysical work has been completed including gravity, resistivity, and airborne magnetic surveys. Several new seismic profiles are planned to provide more focused siting and drilling plans. These new geophysical surveys are being integrated into the combined thermal, hydrologic, and subsurface stratigraphic information data sets to provide a

189

Direct-Current Resistivity Survey At Lualualei Valley Area (Thomas, 1986) |  

Open Energy Info (EERE)

Lualualei Valley Area (Thomas, 1986) Lualualei Valley Area (Thomas, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Lualualei Valley Area (Thomas, 1986) Exploration Activity Details Location Lualualei Valley Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes Three Schlumberger resistivity soundings were performed in Lualualei Valley (Mattice and Kauahikaua, 1979). K840 Interpretation of the resistivity soundings suggests that the source of the warm water layer within the valley was the dense dike complex associated with the ancient magma chamber of Waianae volcano. References Donald M. Thomas (1 January 1986) Geothermal Resources Assessment In Hawaii

190

Direct-Current Resistivity Survey At Northern Basin & Range Region  

Open Energy Info (EERE)

Region Region (Pritchett, 2004) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Northern Basin & Range Region (Pritchett, 2004) Exploration Activity Details Location Northern Basin and Range Geothermal Region Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes NOTE: These are theoretical/computer simulation tests of various methods on eight hypothetical 'model' basing-and-range geothermal systems. "The 300-meter heat flow holes are essentially useless for finding the "hidden" reservoirs. Clearly, the best results are obtained from the SP and MT surveys, with DC resistivity a close third. It is concluded that the best

191

Qualification High Voltage Testing of Short Triax HTS Cables in the Laboratory  

SciTech Connect (OSTI)

In order to qualify the electrical insulation design of future HTS cables installed in the electric grid, a number of high voltage qualification tests are generally performed in the laboratory on either single-phase model cables and/or actual three-phase cable samples. Prior to installation of the 200-m Triax HTS cable at the American Electric Power Bixby substation near Columbus, Ohio, in September, 2006, such tests were conducted on both single-phase model cables made at ORNL and tri-axial cable sections cut off from cable made on a production run. The three-phase tri-axial design provides some specific testing challenges since the ground shield and three phases are concentric about a central former with each phase separated by dielectric tape insulation immersed in liquid nitrogen. The samples were successfully tested and qualified for partial discharge inception, AC withstand, and lightning impulse where voltage is applied to one phase with the other phases grounded. In addition one of the phase pairs was tested for dc withstand as a ldquoworst caserdquo scenario to simulate the effect of VLF (Very Low Frequency) tests on the actual cable installed at the Bixby site. The model and prototype cables will be described and the high voltage test results summarized.

James, David Randy [ORNL; Sauers, Isidor [ORNL; Ellis, Alvin R [ORNL; Tuncer, Enis [ORNL; Gouge, Michael J [ORNL; Demko, Jonathan A [ORNL; Duckworth, Robert C [ORNL; Rey, Christopher M [ORNL

2009-01-01T23:59:59.000Z

192

High-voltage nanosecond pulses in a low-pressure radio-frequency discharge  

Science Journals Connector (OSTI)

An influence of a high-voltage (3–17 kV) 20 ns pulse on a weakly-ionized low-pressure (0.1–10 Pa) capacitively coupled radiofrequency (RF) argon plasma is studied experimentally. The plasma evolution after pulse exhibits two characteristic regimes: a bright flash, occurring within 100 ns after the pulse (when the discharge emission increases by 2–3 orders of magnitude over the steady-state level), and a dark phase, lasting a few hundreds ?s (when the intensity of the discharge emission drops significantly below the steady-state level). The electron density increases during the flash and remains very large at the dark phase. 1D3V particle-in-cell simulations qualitatively reproduce both regimes and allow for detailed analysis of the underlying mechanisms. It is found that the high-voltage nanosecond pulse is capable of removing a significant fraction of plasma electrons out of the discharge gap, and that the flash is the result of the excitation of gas atoms, triggered by residual electrons accelerated in the electric field of immobile bulk ions. The secondary emission from the electrodes due to vacuum UV radiation plays an important role at this stage. High-density plasma generated during the flash provides efficient screening of the RF field (which sustains the steady-state plasma). This leads to the electron cooling and, hence, onset of the dark phase.

M. Y. Pustylnik; L. Hou; A. V. Ivlev; L. M. Vasilyak; L. Couëdel; H. M. Thomas; G. E. Morfill; V. E. Fortov

2013-06-10T23:59:59.000Z

193

Method of detecting the direction of arcing faults on power distribution feeders  

E-Print Network [OSTI]

of overcurrent relays, which Journal model is IEEE transactions on Power Delivery is required for distribution system reliability. The traveling wave directionality al- gorithms also require fairly substantial change in voltage for proper operation... is of significant magnitude to cause a current reversal in the case of a reverse fault [18]. 2. Traveling Wave Relaying The need for more accurate and fast detection of fault and direction of very high voltage transmission lines, was the base of invention...

Fernando, W. Anand Krisantha

2012-06-07T23:59:59.000Z

194

The MAPS Program in the Pacific Northwest: Current Status and Future Direction  

E-Print Network [OSTI]

The MAPS Program in the Pacific Northwest: Current Status and Future Direction Report Submitted #12;#12;The MAPS Program in the Pacific Northwest - i TABLE OF CONTENTS EXECUTIVE SUMMARY........................................................................................................................................... 10 Adult Capture Rates and Station Longevity at MAPS Stations in the Pacific Northwest Region

DeSante, David F.

195

Nickel catalyst faceting in plasma-enhanced direct current chemical vapor deposition of carbon nanofibers  

E-Print Network [OSTI]

1 Nickel catalyst faceting in plasma-enhanced direct current chemical vapor deposition of carbon vapor deposition with Ni catalysts on the top of nanofibers. Transmission electron microscopy was used to study the morphology and crystallography of Ni catalysts, which are essential for the nucleation

Paris-Sud XI, Université de

196

Direct evidence for local oscillatory current sources and intracortical phase gradients in turtle  

E-Print Network [OSTI]

Direct evidence for local oscillatory current sources and intracortical phase gradients in turtle of several species. In turtle, these oscillations take the form of linear and circular traveling waves the origin of wave propagation in turtle visual cortex, we performed simultaneous measurements of the local

Kleinfeld, David

197

Current Directions of Structural Health Monitoring and Control in USA Satish Nagarajaiah1,  

E-Print Network [OSTI]

Current Directions of Structural Health Monitoring and Control in USA Satish Nagarajaiah1,§, 1 Prof.,Dept. of Civil & Env./Dept of Mech. Eng. & Mat. Sc., Rice Univ., Houston, TX 77005, U.S.A. 2 Prof.,Dept. of Mech. Aero. and Struc. Eng., Washington Univ., St. Louis, MO 63130, U.S.A. 3 Asst. Prof

Lynch, Jerome P.

198

Direct-Current Resistivity Survey At Raft River Geothermal Area (1983) |  

Open Energy Info (EERE)

Raft River Geothermal Area (1983) Raft River Geothermal Area (1983) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Raft River Geothermal Area (1983) Exploration Activity Details Location Raft River Geothermal Area Exploration Technique Direct-Current Resistivity Survey Activity Date 1983 Usefulness not indicated DOE-funding Unknown Notes The objectives of the resistivity measurements were to determine if measureable changes could be observed and whether they could be used to infer the direction of fluid flow. Most of the apparent resistivity changes observed after the injection phase of Test 5 are smaller than the estimated standard deviation of the measurements. However, the contour map of the changes suggest an anomalous trend to the northeast which is similar to the

199

Bias current influence on the characteristic of the magnetic-controlled switcher type fault current limiter  

Science Journals Connector (OSTI)

A novel magnetic-controlled switcher type fault current limiter (FCL) for high voltage electric network is presented. The current limiting principle of the FCL and the bias current influence on the characteristic...

Yan-xia Pan ???; Jian-guo Jiang ???

2009-06-01T23:59:59.000Z

200

Fluid modeling of radio frequency and direct currents in a biased magnetized plasma  

SciTech Connect (OSTI)

This model aims at simulating a magnetized plasma column connected on one side to a probe and on the other side to an ICRH (Ion Cyclotron Resonant Heating) antenna. This is a double probe modeling of a plasma flux tube exchanging perpendicular currents: rf polarization current and dc currents (inertia, viscous, and friction) perpendicular to the magnetic field. A self consistent solution for the rectified potential and the density is obtained under the assumptions of flute hypothesis, inertialess electrons, and no collision in parallel direction. The main effect of rf biasing on the antenna side is to shift the IV characteristic so that the floating potential can be increased up to ln(I{sub 0}(eV{sub rf}/(k{sub B}T{sub e}))), with I{sub 0} the modified Bessel function of the first kind. On the contrary, the effect of dc currents is to decrease the plasma potential and the sheath potential which can be lower than 3k{sub B}T{sub e}/e or even be negative. Experimental characteristics are well matched by the 1D fluid code and exhibit very high negative currents (more than 30 j{sub i} the ion saturation current) for high positive biasing of the probe and for long flux tube (10 m). The non-saturation of the electron current is here due to high transverse transport enhanced by convective fluxes and dc currents able to bring an amount of density around the biased flux tube. During comparisons with experiments, the floating potential measured by a reciprocating probe is recovered by the code revealing that for a 120 V measured peak potential on the probe, the rf potential on the ICRH antenna is twice this value. Finally, the density profile can be flattened or steepened as a function of the transverse dc current direction.

Faudot, E.; Heuraux, S. [IJL-P2M UMR 7198 CNRS, F-54506 Vandoeuvre les Nancy, IJL, P2M-Faculte des Sciences, Vandoeuvre les Nancy 54506 (France); Kubic, M.; Gunn, J.; Colas, L. [CEA, IRFM, F-13108 Saint-Paul-lez-Durance (France)

2013-04-15T23:59:59.000Z

Note: This page contains sample records for the topic "high-voltage direct current" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

ANUEADflM-31 Electric Power High-Voltage Transmission Lines:  

Office of Scientific and Technical Information (OSTI)

ANUEADflM-31 ANUEADflM-31 Electric Power High-Voltage Transmission Lines: Design Options, Cost, and Electric and Magnetic Field Levels by J.B. Stoffel,' E.D. Pentecost, R.D. Roman, and P.A. Traczyk Environmental Assessment Division, Argonne National Laboratory, 9700 South Cass Avenue, Argonne, Illinois 60439 November 1994 Work sponsored by United States Department of Energy, Assistant Secretary for Fossil Energy, Office of Fuels Program Stoffel is affiliated with Argonne's Electronics and Computing Technologies Division. D4SlRlBUTlON OF THIS DOCUMENT IS UNLiMltEb - . - . - . - . ... - , . ^ ~ .. , . . . , . . _ I T h i s report i s printed on recycled paper. @ . . .. . ' . . . A :_ - .. ., . . DISCLAIMER This report was .prepared as an account of work sponsored by an agency of the United States Government. Neither

202

ESS 2012 Peer Review - Low Cost, Manufacturable High Voltage Power Module for ESS - Brandon Passmore, APEI  

Broader source: Energy.gov (indexed) [DOE]

W. Research Center Blvd. * Fayetteville, AR 72701 * (479) 443-5759 W. Research Center Blvd. * Fayetteville, AR 72701 * (479) 443-5759 Design and Development of a Low Cost, Manufacturable High Voltage Power Module for Energy Storage Systems Phase I SBIR September 27, 2012 Brandon Passmore, PhD Sr. Electronics Packaging Research Engineer Email: bpassmo@apei.net Acknowledgements * I would like to thank Dr. Imre Gyuk of the DOE Energy Storage Systems Program and Dr. Stan Atcitty for technical support * I would also like to thank 2 Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

203

Artificial SEI Enables High-Voltage Lithium-ion Batteries | ornl.gov  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Functional Materials for Energy Functional Materials for Energy Artificial SEI Enables High-Voltage Lithium-ion Batteries September 03, 2013 Efficacy of Lipon coating as an artificial SEI for suppression of electrolyte decomposition on a 5V spinel cathode: coulombic efficiency was measured versus cycle numbers at samples with different coating thickness. An artificial solid electrolyte interphase (SEI) of lithium phosphorus oxynitride (Lipon) enables the use of 5V cathode materials with conventional carbonate electrolytes in lithium-ion batteries. Five volt cathode materials, such as LiNi0.5Mn1.5O4, are desirable to provide higher energy, however conventional carbonate electrolytes decompose above 4.5V compromising the battery performance. This work shows that Lipon coating suppresses the electrolyte decomposition, as measured by the

204

High Voltage Performance of the Beam Screen of the LHC Injection Kicker Magnets  

E-Print Network [OSTI]

The LHC injection kicker magnets include beam screens to shield the ferrite yokes against wakefields resulting from the high intensity beam. The screening is provided by conductors lodged in the inner wall of a ceramic support tube. The design of the beam screen has been upgraded to overcome limitations and permit LHC operation with increasingly higher bunch intensity and short bunch lengths: the new design also significantly reduces the electric field associated with the screen conductors, decreasing the probability of electrical breakdown. The high voltage conditioning process for the upgraded kicker magnets is presented and discussed. In addition a test setup has been utilized to study flashover, on the inner wall of the ceramic tube, as a function of both applied voltage and vacuum pressure: results from the test setup are presented.

Barnes, MJ; Bregliozzi, G; Calatroni, S; Costa Pinto, P; Day, H; Ducimetière, L; Kramer, T; Namora, V; Mertens, V; Taborelli, M

2014-01-01T23:59:59.000Z

205

Constructing ‘population’ criteria for the comparison of different options for a high voltage line route  

Science Journals Connector (OSTI)

This paper presents a method for comparing the sensitiveness of people to different possible options for the route of High Voltage transmission lines. It has been tested on practical cases. First, we create special dimensions and scales in order to evaluate the different zones of a studied area. Then, the different options for the route of HV lines (which are a succession of different zones) have to be compared. The construction of criteria permitting the comparison of different options raises a theoretical issue: how to punctualise the geographic distribution or the grades of the different zones of an option, in order to reflect preferences? Different methods of punctualisation are proposed which could apply to other cases. But the purpose of the paper is merely to show that these methods of punctualisation are not neutral, they cannot reflect all the characteristics of a distribution of grades.

Nathalie Grassin

1986-01-01T23:59:59.000Z

206

EIS-0107: Mead-Phoenix +500-kV Direct Current Transmission Line  

Broader source: Energy.gov [DOE]

The U.S. Department of Energy’s Western Area Power Administration (WAPA) prepared this statement to analyze the potential environmental and socioeconomic impacts arising from WAPA and regional project sponsors’ proposal to construct a 500 kilovolt (kV) alternating current (AC) transmission line with the capability to be upgraded later to 500kV direct current (DC), connecting the Westwing Substation, located north of Phoenix, Arizona, with a new McCullough II Substation, located approximately 14 miles west of Boulder City, Nevada. This statement modifies a previously prepared federal statement from which the participants' election to proceed had not occurred at the time this statement was prepared.

207

Direct-Current Resistivity Survey At Valles Caldera - Sulphur Springs Area  

Open Energy Info (EERE)

Wilt & Haar, 1986) Wilt & Haar, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Valles Caldera - Sulphur Springs Area (Wilt & Haar, 1986) Exploration Activity Details Location Valles Caldera - Sulphur Springs Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness not indicated DOE-funding Unknown Notes Telluric profiles, magnetotelluric sounding, dc resistivity, and electromagnetic sounding surveys were all performed over the caldera in hopes of outlining deep drilling targets (Group 7 Inc., 1972; McPhar, 1973; Geonomics Inc., 1976). These data are used to help define the electrical structure in the reservoir region. Some of the data were reinterpreted using computer models, and interpretations from the various surveys were

208

Direct-Current Resistivity At Kilauea East Rift Area (Thomas, 1986) | Open  

Open Energy Info (EERE)

Kilauea East Rift Area (Thomas, 1986) Kilauea East Rift Area (Thomas, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity At Kilauea East Rift Area (Thomas, 1986) Exploration Activity Details Location Kilauea East Rift Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes Electrical resistivity studies performed on the Kilauea East Rift Zone have employed a variety of techniques. Bipole mapping was conducted by Keller et al. (1977a) as part of the Hawaii Geothermal Project (HGP) geoscience program and was able to provide data on the regional resistivity structure of the summit and eastern flank of Kilauea. The model developed indicated several different types of resistivity sections depending on the location

209

Direct-Current Resistivity At Kawaihae Area (Thomas, 1986) | Open Energy  

Open Energy Info (EERE)

Kawaihae Area (Thomas, 1986) Kawaihae Area (Thomas, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity At Kawaihae Area (Thomas, 1986) Exploration Activity Details Location Kawaihae Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness not indicated DOE-funding Unknown Notes In addition to the aeromagnetic data, the field survey program in Kawaihae included six Schlumberger resistivity soundings between Kawaihae and Waimea (Kauahikaua and Mattice, 1981). The results of these sounding (Fig. 35) detected apparent resistivity differences in the surface rock depending on whether the soundings were done on Kohala or Mauna Kea lavas (Figs 36, 37), whereas uniform resistivities of 650- 850 ohm.m were found at depths of

210

Direct-Current Resistivity At Dixie Valley Geothermal Field Area (Laney,  

Open Energy Info (EERE)

2005) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity At Dixie Valley Geothermal Field Area (Laney, 2005) Exploration Activity Details Location Dixie Valley Geothermal Field Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes Structural Controls, Alteration, Permeability and Thermal Regime of Dixie Valley from New-Generation Mt/Galvanic Array Profiling, Phillip Wannamaker. A new-generation MT/DC array resistivity measurement system was applied at the Dixie Valley thermal area. Basic goals of the survey are 1), resolve a fundamental structural ambiguity at the Dixie Valley thermal area (single rangefront fault versus shallower, stepped pediment; 2), delineate fault

211

Direct-Current Resistivity Survey At Cove Fort Area (Warpinski, Et Al.,  

Open Energy Info (EERE)

Cove Fort Area (Warpinski, Et Al., Cove Fort Area (Warpinski, Et Al., 2002) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Cove Fort Area (Warpinski, Et Al., 2002) Exploration Activity Details Location Cove Fort Geothermal Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes The project at Cove Fort/Sulphurdale in Utah, T26S R6/7W, is concerned with locating and drilling a 900-meter well to explore the western extension of the Cove Fort-Sulphurdale geothermal area. The geophysical exploration consisted of resistivity, ground magnetic, and microgravity surveys that were made to site the well in an optimum location. References N. R. Warpinski, A. R. Sattlerl, D. A. Sanchez (2002) Geothermal

212

Direct-Current Resistivity At Lightning Dock Area (Cunniff & Bowers, 2005)  

Open Energy Info (EERE)

Lightning Dock Area (Cunniff & Bowers, 2005) Lightning Dock Area (Cunniff & Bowers, 2005) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity At Lightning Dock Area (Cunniff & Bowers, 2005) Exploration Activity Details Location Lightning Dock Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness not indicated DOE-funding Unknown Notes Two electrical resistivity survey lines were run in the project area: a southern east-west line along Caliche Road, and a northern east-west line in the south half Section 6, T25S, R19W (figure 5). The Caliche Road line is located south of the greenhouse complex and was run along the road, which was also used for a gravity traverse. The northern line, named "Church Road,"+K846 was parallel to the east-west road and gravity

213

Direct-Current Resistivity Survey At Kilauea East Rift Area (Thomas, 1986)  

Open Energy Info (EERE)

Kilauea East Rift Area (Thomas, 1986) Kilauea East Rift Area (Thomas, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Kilauea East Rift Area (Thomas, 1986) Exploration Activity Details Location Kilauea East Rift Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes Electrical resistivity studies performed on the Kilauea East Rift Zone have employed a variety of techniques. Bipole mapping was conducted by Keller et al. (1977a) as part of the Hawaii Geothermal Project (HGP) geoscience program and was able to provide data on the regional resistivity structure of the summit and eastern flank of Kilauea. The model developed indicated several different types of resistivity sections depending on the location

214

Direct-Current Resistivity Survey At Valles Caldera - Redondo Area (Wilt &  

Open Energy Info (EERE)

Wilt & Wilt & Haar, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Valles Caldera - Redondo Area (Wilt & Haar, 1986) Exploration Activity Details Location Valles Caldera - Redondo Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness not indicated DOE-funding Unknown Notes Telluric profiles, magnetotelluric sounding, dc resistivity, and electromagnetic sounding surveys were all performed over the caldera in hopes of outlining deep drilling targets (Group 7 Inc., 1972; McPhar, 1973; Geonomics Inc., 1976). These data are used to help define the electrical structure in the reservoir region. Some of the data were reinterpreted using computer models, and interpretations from the various surveys were

215

Direct-Current Resistivity At Honokowai Area (Thomas, 1986) | Open Energy  

Open Energy Info (EERE)

Honokowai Area (Thomas, 1986) Honokowai Area (Thomas, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity At Honokowai Area (Thomas, 1986) Exploration Activity Details Location Honokowai Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness not useful DOE-funding Unknown Notes Three Schlumberger resistivity surveys were attempted on the alluvial plain around Honokowai (Fig. 22). Two of the soundings penetrated to a moderate-resistivity basement, interpreted to be seawater-saturated basalt, whereas the other sounding encountered a high-resistivity intermediate layer which could not be adequately penetrated to allow resolution of the basement resistivity (Mattice, 1981). References Donald M. Thomas (1 January 1986) Geothermal Resources Assessment In

216

Direct-Current Resistivity Survey At Honokowai Area (Thomas, 1986) | Open  

Open Energy Info (EERE)

Honokowai Area (Thomas, 1986) Honokowai Area (Thomas, 1986) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Honokowai Area (Thomas, 1986) Exploration Activity Details Location Honokowai Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness not useful DOE-funding Unknown Notes Three Schlumberger resistivity surveys were attempted on the alluvial plain around Honokowai (Fig. 22). Two of the soundings penetrated to a moderate-resistivity basement, interpreted to be seawater-saturated basalt, whereas the other sounding encountered a high-resistivity intermediate layer which could not be adequately penetrated to allow resolution of the basement resistivity (Mattice, 1981). References Donald M. Thomas (1 January 1986) Geothermal Resources Assessment In

217

Direct-Current Resistivity Survey At Stillwater Area (Laney, 2005) | Open  

Open Energy Info (EERE)

Stillwater Area (Laney, 2005) Stillwater Area (Laney, 2005) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Direct-Current Resistivity Survey At Stillwater Area (Laney, 2005) Exploration Activity Details Location Stillwater Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes Structural Controls, Alteration, Permeability and Thermal Regime of Dixie Valley from New-Generation Mt/Galvanic Array Profiling, Phillip Wannamaker. A new-generation MT/DC array resistivity measurement system was applied at the Dixie Valley thermal area. Basic goals of the survey are 1), resolve a fundamental structural ambiguity at the Dixie Valley thermal area (single rangefront fault versus shallower, stepped pediment; 2), delineate fault

218

The effects of direct-current magnetic fields on turtle retinas vitro  

SciTech Connect (OSTI)

Direct-current magnetic fields of 10 to 100 gauss cause a significant short-term reduction of the in vitro electroretinographic b-wave response in turtle retina. This response compression is not accompanied by the usual reduction in retinal sensitivity that occurs with background illumination. Furthermore, this effect is obtained only briefly after the offset of ambient lighting in the diurnal light-dark cycle of nonhibernating animals.

Raybourn, M.S.

1983-05-13T23:59:59.000Z

219

Leveraging the LEDA high voltage power supply systems for the LANSCE refurbishment project  

SciTech Connect (OSTI)

The LANSCE Refurbishment Project (LANSCE-R) will revitalize the LANSCE accelerator infrastructure. Much of the equipment has been in use for over 39 years and is approaching the end of its design lifetime. As obsolescence issues make like-for-like replacements increasingly more expensive, modern systems with lower costs become a reasonable alternative. As part of the LANSCE-R project, four of the seven HV power supplies for the 805 MHz RF klystrons will be replaced. The present and future requirements for these power supplies influence the selection of replacement options. Details of the HV power supply replacement requirements and the different replacement options will be discussed. One option is to use four 95 kV, 21 A DC power supplies originally installed nearby as part of the Low Energy Demonstration Accelerator (LEDA) project. Significant material and labor cost savings can be achieved by leaving these supplies installed where they are and building a HV transport system to bring high voltage power from the existing LEDA facility to the LANSCE facility. The different replacement options will be compared based on material and labor costs as offset by long-term energy savings.

Bradley Iii, Joseph Thomas [Los Alamos National Laboratory; Rees, Daniel E [Los Alamos National Laboratory; Roybal, William T [Los Alamos National Laboratory; Young, Karen A [Los Alamos National Laboratory

2008-01-01T23:59:59.000Z

220

Redesign of the H-Bridge Switch Plate of the SNS High Voltage Converter Modulator  

SciTech Connect (OSTI)

The 1-MW High Voltage Converter Modulators [1] have operated in excess of 250,000 hours at the Spallation Neutron Source. Increased demands on the accelerator performance require increased modulator reliability. An effort is underway at SLAC National Accelerator Laboratory to redesign the modulator H-bridge switch plate with the goals of increasing reliability and performance [2]. The major difference between the SLAC design and the existing design is the use of press-pack IGBTs. Compared to other packaging options, these IGBTs have been shown to have increased performance in pulsed-power applications, have increased cooling capability, and do not fragment and disassemble during a fault event. An overview of the SLAC switch plate redesign is presented. Design steps including electrical modeling of the modulator and H-bridge, development of an integrated IGBT clamping mechanism, and fault tests are discussed. Experimental results will be presented comparing electrical performance of the SLAC switch plate to the existing switchplate under normal and fault conditions.

Kemp, M.A.; Burkhart, C.; Nguyen, M.N.; /SLAC; Anderson, D.E.; /Oak Ridge

2009-05-07T23:59:59.000Z

Note: This page contains sample records for the topic "high-voltage direct current" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Influence of high voltage atmospheric cold plasma process parameters and role of relative humidity on inactivation of Bacillus atrophaeus spores inside a sealed package  

Science Journals Connector (OSTI)

SummaryBackground Non-thermal plasma has received much attention for elimination of microbial contamination from a range of surfaces. Aim This study aimed to determine the effect of a range of dielectric barrier discharge high voltage atmospheric cold plasma (HVACP) parameters for inactivation of Bacillus atrophaeus spores inside a sealed package. Methods A sterile polystyrene Petri dish containing B. atrophaeus spore strip (spore population 2.3 × 106/strip i.e. 6.36 log10/strip) was placed in a sealed polypropylene container and was subjected to HVACP treatment. The HVACP discharge was generated between two aluminium plate electrodes using a high voltage of 70 kVRMS. The effects of process parameters, including treatment time, mode of exposure (direct/indirect), and working gas types, were evaluated. The influence of relative humidity on HVACP inactivation efficacy was also assessed. The inactivation efficacy was evaluated using colony counts. Optical absorption spectroscopy (OAS) was used to assess gas composition following HVACP exposure. Findings A strong effect of process parameters on inactivation was observed. Direct plasma exposure for 60 s resulted in ?6 log10 cycle reduction of spores in all gas types tested. However, indirect exposure for 60 s resulted in either 2.1 or 6.3 log10 cycle reduction of spores depending on gas types used for HVACP generation. The relative humidity (RH) was a critical factor in bacterial spore inactivation by HVACP, where a major role of plasma-generated species other than ozone was noted. Direct and indirect HVACP exposure for 60 s at 70% RH recorded 6.3 and 5.7 log10 cycle reduction of spores, respectively. Conclusion In summary, a strong influence of process parameters on spore inactivation was noted. Rapid in-package HVACP inactivation of bacterial spores within 30–60 s demonstrates the promising potential application for reduction of spores on medical devices and heat-sensitive materials.

S. Patil; T. Moiseev; N.N. Misra; P.J. Cullen; J.P. Mosnier; K.M. Keener; P. Bourke

2014-01-01T23:59:59.000Z

222

Alternative Energy Development and China's Energy Future  

E-Print Network [OSTI]

high voltage direct current (HVDC) transmission which canhigh voltage direct current (HVDC) transmission, an increase

Zheng, Nina

2012-01-01T23:59:59.000Z

223

Breaking the ice: de-icing power transmission lines with high-frequency, high-voltage excitation  

E-Print Network [OSTI]

Breaking the ice: de-icing power transmission lines with high-frequency, high-voltage excitation of this work in other works must be obtained from the IEEE. #12;CING OF POWER TRANSMISSION lines during winter that applies 33-kV, 100-kHz power. TheoverallsystemisillustratedinFigure1.Itcouldbede- ployed in two different

224

A three-level buck converter to regulate a high-voltage DC-to-AC inverter  

E-Print Network [OSTI]

A three-level buck converter is designed and analyzed, and shown to be suitable as a high-voltage down converter as a pre-regulation stage for a 600 watt DC-to-AC power inverter. Topology selection for the inverter is ...

Schrock, Kenneth C

2008-01-01T23:59:59.000Z

225

Coulomb contribution to the direct current electrical conductivity of dense partially ionized plasmas  

Science Journals Connector (OSTI)

The Coulomb contribution to the electrical conductivity of partially ionized plasmas is discussed and its general behavior is investigated. Recent experiments on the direct current conductivity in shock wave induced argon and xenon plasmas are analyzed in this context. Within the relaxation time approach the Coulomb contribution is extracted by eliminating the contribution of scattering from neutrals. Alternatively the Coulomb contribution can be calculated directly within linear-response theory. In particular from the latter approach a generalized Spitzer factor is derived for taking into account electron-electron interactions within the relaxation time approximation. Experimental results for the Coulomb contribution to the electrical conductivity are in reasonable agreement with an interpolation formula derived from linear-response theory.

J. R. Adams; N. S. Shilkin; V. E. Fortov; V. K. Gryaznov; V. B. Mintsev; R. Redmer; H. Reinholz; G. Röpke

2007-01-01T23:59:59.000Z

226

Four-point probe measurements of a direct current potential drop on layered conductive cylinders  

Science Journals Connector (OSTI)

We have determined the steady state electric field due to direct current flowing via point contacts at the cylindrical surface of a uniformly layered conductive rod of finite length. The solution allows one to use four-point probe potential drop measurements to estimate the conductivity or thickness of the layer assuming that the other parameters are known. The electrical potential in the rod has a zero radial derivative at its surface except at the injection and extractions points. This means that the required solution can be expressed in terms of a Green's function satisfying a Neumann boundary condition. Four-point measurements have been made to demonstrate the validity of theoretical results.

Yi Lu; John R Bowler

2012-01-01T23:59:59.000Z

227

Current-based direct power control of a DFIG under unbalanced grid voltage  

Science Journals Connector (OSTI)

Abstract A novel current-based direct power control (CB-DPC) strategy for a grid-connected doubly-fed induction generator (DFIG) is proposed. The reported control scheme is applicable to DFIG-based variable-speed wind turbines that operate under unbalanced network voltages. The required DFIG rotor voltage for precise regulation of the stator active and reactive output powers and accurate elimination of their inherent pulsations are directly obtained using a nonlinear integral sliding-mode control (ISMC) scheme. Compared with other control methods, the proposed strategy is simpler since it is not based on the symmetrical components theory, does not need multiple synchronous coordinate transformations, and only requires DFIG voltage and current values as its inputs. Constant switching frequency of the rotor-side converter (RSC) is achieved by means of space vector pulse-width modulation (SVPWM) technique. Uncertainties in the parameters of the generator are included in the design. A compensation strategy is also proposed for tracking error mitigation of the powers that occur due to elimination of the chattering phenomena in the ISMC scheme. Simulation results on a 2MW DFIG under different operating conditions are presented to validate the effectiveness and robustness of the proposed method.

Mohammad Farshadnia; Seyed Abbas Taher

2014-01-01T23:59:59.000Z

228

New live line tester for porcelain suspension insulators on high-voltage power lines  

SciTech Connect (OSTI)

Suspension insulator assemblies known as insulator strings are used in overhead power transmission lines to mechanically support high-voltage conductors while providing adequate insulation to withstand switching and lightning overvoltages. Since the useful life in service of the individual insulator elements making up these strings is hard to predict, they must be verified periodically to insure that adequate line reliability is maintained at all times. Over the years many testing methods have been used for this purpose, each one with its own advantages and disadvantages. Until now at Hydro-Quebec, porcelain insulators had been tested by the buzz method which simply consists of applying a short-circuit to each insulator in a string and listening for a buzz-like sound indicating a good insulator. However, safety considerations that preclude short-circuiting insulators and other disadvantages of that method have led Hydro-Quebec to undertake and complete the development of a new insulator tester. The working principle of this new device is based on the automatic measurement and recording of the electric field along the insulator string which decreases considerably in front of an internally-shorted insulator. The tester is slid along the string while the insulators are counted automatically. The information from tests on up to 200 strings can be stored in the device to be later transferred in a host computer for interpretation and/or permanent storage. The new tester also gives information on voltage distribution along the insulator strings which can be useful for the design of future power transmission lines.

Vaillancourt, G.H.; St-Jean, M. (Hydro-Quebec, Varennes, Quebec (Canada)); Bellerive, J.P. (Hydro-Quebec, Montreal, Quebec (Canada)); Jean, C. (Positron Inc., Montreal, Quebec (Canada))

1994-01-01T23:59:59.000Z

229

Direct-Current Resistivity Survey At Central Nevada Seismic Zone Region  

Open Energy Info (EERE)

Survey At Central Nevada Survey At Central Nevada Seismic Zone Region (Pritchett, 2004) Exploration Activity Details Location Central Nevada Seismic Zone Geothermal Region Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness useful DOE-funding Unknown Notes NOTE: These are theoretical/computer simulation tests of various methods on eight hypothetical 'model' basing-and-range geothermal systems. "The 300-meter heat flow holes are essentially useless for finding the "hidden" reservoirs. Clearly, the best results are obtained from the SP and MT surveys, with DC resistivity a close third. It is concluded that the best way to find "hidden" basin and range geothermal resources of this general type is to carry out simultaneous SP and low-frequency MT surveys, and then

230

Direct-Current Resistivity At Lahaina-Kaanapali Area (Thomas, 1986) | Open  

Open Energy Info (EERE)

At Lahaina-Kaanapali Area At Lahaina-Kaanapali Area (Thomas, 1986) Exploration Activity Details Location Lahaina-Kaanapali Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness not indicated DOE-funding Unknown Notes Four Schlumberger soundings were performed along the coastal strip adjacent to Lahaina town (Fig. 22). Three of the four soundings were able to detect a moderate to low-resistivity basement that was interpreted to be basalt saturated with seawater at 20degrees C (Mattice, 1981). None of the resistivity sounding data in this area indicated subsurface resistivities lower than could be accounted for by local ambient temperatures (Mattice and Lienert, 1980). References Donald M. Thomas (1 January 1986) Geothermal Resources Assessment In Hawaii

231

Lagrangian Modeling at Sandia National Laboratories: Current Status and Future Directions  

National Nuclear Security Administration (NNSA)

Lagrangian Modeling at Sandia National Laboratories: Lagrangian Modeling at Sandia National Laboratories: Current Status and Future Directions A. C. Robinson, * Martin W. Heinstein, * Guglielmo Scovazzi * * Sandia National Laboratories, New Mexico, 87185 Efficient Lagrangian methodologies for quadrilaterals and hexahedral meshes have been available for a number of years. Mesh generation issues for complex three-dimensional geometries can, however, be a severe limiting factor. Mesh generation for triangular and tetrahedral meshes is readily available, but solid mechanics discretizations on these meshes are not so well established because of problems with locking. We review a relatively new node-based uniform strain element as well as an SUPG stabilized formulation that hold promise for effective simulations

232

Direct-Current Resistivity Survey At Lahaina-Kaanapali Area (Thomas, 1986)  

Open Energy Info (EERE)

Survey At Survey At Lahaina-Kaanapali Area (Thomas, 1986) Exploration Activity Details Location Lahaina-Kaanapali Area Exploration Technique Direct-Current Resistivity Survey Activity Date Usefulness not indicated DOE-funding Unknown Notes Four Schlumberger soundings were performed along the coastal strip adjacent to Lahaina town (Fig. 22). Three of the four soundings were able to detect a moderate to low-resistivity basement that was interpreted to be basalt saturated with seawater at 20degrees C (Mattice, 1981). None of the resistivity sounding data in this area indicated subsurface resistivities lower than could be accounted for by local ambient temperatures (Mattice and Lienert, 1980). References Donald M. Thomas (1 January 1986) Geothermal Resources Assessment In

233

Mechanism behind self-sustained oscillations in direct current glow discharges and dusty plasmas  

SciTech Connect (OSTI)

An alternative explanation to the mechanism behind self-sustained oscillations of ions in direct current (DC) glow discharges is provided. Such description is distinguished from the one provided by the fluid models, where oscillations are attributed to the positive feedback mechanism associated with photoionization of particles and photoemission of electrons from the cathode. Here, oscillations arise as consequence of interaction between an ion and the surface charges induced by it at the bounding electrodes. Such mechanism provides an elegant explanation to why self-sustained oscillations occur only in the negative resistance region of the voltage-current characteristic curve in the DC glow discharges. Furthermore, this alternative description provides an elegant explanation to the formation of plasma fireballs in the laboratory plasma. It has been found that oscillation frequencies increase with ion's surface charge density, but at the rate which is significantly slower than it does with the electric field. The presented mechanism also describes self-sustained oscillations of ions in dusty plasmas, which demonstrates that self-sustained oscillations in dusty plasmas and DC glow discharges involve common physical processes.

Cho, Sung Nae [Devices R and D Center, Samsung Advanced Institute of Technology, Samsung Electronics Co., Ltd., Mt. 14-1 Nongseo-dong, Giheung-gu, Yongin-si, Gyeonggi-do 446-712 (Korea, Republic of)

2013-04-15T23:59:59.000Z

234

Using Dielectric Losses to De-Ice Power Transmission Lines with 100 kHz High-Voltage  

E-Print Network [OSTI]

capable of exciting a 1 m test line to 30 kV has been tested and show to be capable of removing a 7 mm iceUsing Dielectric Losses to De-Ice Power Transmission Lines with 100 kHz High-Voltage Excitation J DIELECTRIC LOSSES TO DE-ICE POWER TRANSMISSION LINES . . . 1 Using Dielectric Losses to De-Ice Power

235

Ionization of Group II A Elements in the Direct Current Plasma: Effects of Ionization Potential on Emission Profiles  

Science Journals Connector (OSTI)

Studies of background corrected ion and atom emission profiles of the group IIA elements in the two-electrode direct current plasma show great variation in both vertical and...

Williams, Ronald R; Coleman, Geoffrey N

1981-01-01T23:59:59.000Z

236

Hemodynamic responses in rat brain during transcranial direct current stimulation: a functional near-infrared spectroscopy study  

Science Journals Connector (OSTI)

In the present study, we monitored hemodynamic responses in rat brains during transcranial direct current stimulation (tDCS) using functional near-infrared spectroscopy (fNIRS). Seven...

Han, Chang-Hee; Song, Hyuna; Kang, Yong-Guk; Kim, Beop-Min; Im, Chang-Hwan

2014-01-01T23:59:59.000Z

237

Measuring surface ocean wave height and directional spectra using an Acoustic Doppler Current Profiler from an autonomous underwater vehicle  

E-Print Network [OSTI]

The Acoustic Doppler Current Profiler (ADCP) is a proven technology which is capable of measuring surface wave height and directional information, however it is generally limited to rigid, bottom mounted applications which ...

Haven, Scott

2012-01-01T23:59:59.000Z

238

Simulation of an Ar/NH{sub 3} low pressure magnetized direct current discharge  

SciTech Connect (OSTI)

A two-dimensional fluid model has been used to investigate the properties of plasma in an Ar/NH{sub 3} low pressure magnetized direct current discharge. We compared the simulation results with the theoretical and experimental results of the other gas discharge in which the magnetic field is considered. Results that obtained using this method are in good agreement with literature. The simulation results show that the positive ammonia ion density follows the positive argon ion density. The Ar{sub 2}{sup +} density is slightly higher than the Ar{sup +} density at 100 mTorr. The largest ammonia ion is NH{sub 3}{sup +} ion, followed by NH{sub 2}{sup +}, NH{sub 4}{sup +}, and NH{sup +} ions. The contribution of NH{sup +} ions to the density of the positive ammonia ions is marginal. The influence of pressure on the plasma discharge has been studied by simulation, and the mechanisms have been discussed. The average plasma density increases as pressure increased. The plasma density appears to be more inhomogeneous than that at the lower pressure. The ratio of charge particles changed as pressure increased. The Ar{sup +} density is slightly higher than the Ar{sub 2}{sup +} density as the pressure increased. It makes NH{sub 4}{sup +} ratio increase as pressure increased. It shows that the electron temperature drops with rising pressure by numerical calculation.

Li Zhi [School of Science, University of Science and Technology Liaoning, Anshan 114051 (China); School of Physics and Optoelectronic Engineering, Dalian University of Technology, Dalian 116024 (China); Zhao Zhen [School of Chemistry and Life Science, Anshan Normal University, Anshan 114007 (China); School of Chemical Engineering, University of Science and Technology Liaoning, Anshan 114051 (China); Li Xuehui [Physiccal Science and Technical College, Dalian University, Dalian 116622 (China)

2013-01-15T23:59:59.000Z

239

Formation of ozone and oxidation of methane in a direct current corona discharge  

E-Print Network [OSTI]

than in the positive corona when using air, while the reverse was observed with oxygen. At low currents and high gas flow rates, the ozone production rate increased linearly with corona current independent of gas flow rate. At high currents... humidity) and positive corona. Their results show: (1) a linear relation between ozone concentration and corona current; (2) an (non- linear) inverse relation between the ozone concentration and air flow; and (3) for a given corona current, the ozone...

Tangirala, Umashanker

1976-01-01T23:59:59.000Z

240

The case for a directional dark matter detector and the status of current experimental efforts  

E-Print Network [OSTI]

We present the case for a dark matter detector with directional sensitivity. This document was developed at the 2009 CYGNUS workshop on directional dark matter detection, and contains contributions from theorists and ...

Battat, James

Note: This page contains sample records for the topic "high-voltage direct current" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Dynamic ON-resistance in high voltage GaN field-effect-transistors  

E-Print Network [OSTI]

Recently, the development of energy efficient electrical power management systems has received considerable interest due to its potential to realize significant energy savings for the world. With current Si-based power ...

Jin, Donghyun

2014-01-01T23:59:59.000Z

242

Measurement of low radioactivity background in a high voltage cable by high resolution inductively coupled plasma mass spectrometry  

SciTech Connect (OSTI)

The measurement of naturally occurring low level radioactivity background in a high voltage (HV) cable by high resolution inductively coupled plasma mass spectrometry (HR ICP MS) is presented in this work. The measurements were performed at the Chemistry Service of the Gran Sasso National Laboratory. The contributions to the radioactive background coming from the different components of the heterogeneous material were separated. Based on the mass fraction of the cable, the whole contamination was calculated. The HR ICP MS results were cross-checked by gamma ray spectroscopy analysis that was performed at the low background facility STELLA (Sub Terranean Low Level Assay) of the LNGS underground lab using HPGe detectors.

Vacri, M. L. di; Nisi, S.; Balata, M. [Gran Sasso National Laboratory, Chemistry Service, SS 17bis km 18.910, 67100 Assergi (Aq) (Italy)] [Gran Sasso National Laboratory, Chemistry Service, SS 17bis km 18.910, 67100 Assergi (Aq) (Italy)

2013-08-08T23:59:59.000Z

243

Effects of Transcranial Direct Current Stimulation (tDCS) on Human Memory.  

SciTech Connect (OSTI)

Training a person in a new knowledge base or skill set is extremely time consuming and costly, particularly in highly specialized domains such as the military and the intelligence community. Recent research in cognitive neuroscience has suggested that a technique called transcranial direct current stimulation (tDCS) has the potential to revolutionize training by enabling learners to acquire new skills faster, more efficiently, and more robustly (Bullard et al., 2011). In this project, we tested the effects of tDCS on two types of memory performance that are critical for learning new skills: associative memory and working memory. Associative memory is memory for the relationship between two items or events. It forms the foundation of all episodic memories, so enhancing associative memory could provide substantial benefits to the speed and robustness of learning new information. We tested the effects of tDCS on associative memory, using a real-world associative memory task: remembering the links between faces and names. Working memory refers to the amount of information that can be held in mind and processed at one time, and it forms the basis for all higher-level cognitive processing. We investigated the degree of transfer between various working memory tasks (the N-back task as a measure of verbal working memory, the rotation-span task as a measure of visuospatial working memory, and Raven's progressive matrices as a measure of fluid intelligence) in order to determine if tDCS-induced facilitation of performance is task-specific or general.

Matzen, Laura E.; Trumbo, Michael Christopher Stefan

2014-10-01T23:59:59.000Z

244

Ice accretions on high–voltage conductors and insulators and related phenomena  

Science Journals Connector (OSTI)

...short-circuit current of the HVAC system is ca. 28 A at the...knowledge, there is no established standard method for eval- uating the...publications will soon be available. Standard methods facilitate the comparison...various outdoor insulator types. Standards will also allow us to compare...

2000-01-01T23:59:59.000Z

245

Direct-current substrate bias effects on amorphous silicon sputter-deposited films for thin film transistor fabrication  

SciTech Connect (OSTI)

The effect that direct current (dc) substrate bias has on radio frequency-sputter-deposited amorphous silicon (a-Si) films has been investigated. The substrate bias produces a denser a-Si film with fewer defects compared to unbiased films. The reduced number of defects results in a higher resistivity because defect-mediated conduction paths are reduced. Thin film transistors (TFTs) that were completely sputter deposited were fabricated and characterized. The TFT with the biased a-Si film showed lower leakage (off-state) current, higher on/off current ratio, and higher transconductance (field effect mobility) than the TFT with the unbiased a-Si film.

Jun, Seung-Ik; Rack, Philip D.; McKnight, Timothy E.; Melechko, Anatoli V.; Simpson, Michael L. [Department of Materials Science and Engineering, University of Tennessee, Knoxville, Tennessee 37996-2200 (United States); Molecular Scale Engineering and Nanoscale Technologies Research Group, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831 (United States)

2005-09-26T23:59:59.000Z

246

Current:  

Office of Legacy Management (LM)

OWNE3 (55) OWNE3 (55) -------- past: _--_-------------------- Current: Owner contacted I-J yes ,Fqna; ------------_------------- if yes, date contacted TYPE OF OPEF(ATION ---__-------_____ c] Research & Development -4 Facility Type ci Production scale testing 0 Pilbt Scale 0 Bench Scale Process 0 Theoretical Studies 0 Sample & Analysis C Productian E Disposal/Storage TYPE OF CONTRACi _------_-------_ tlanuf acturi ng University Research Organizaticn q Prime --. _' cl Other information (i.e., cost price, + fixed fee, unit time % material, qtr) ------- ~----~---~~------__--------- YuncOntractor Purchase Order Contract/Purkhase Order # cc-km ----_----~~-----___--------- --------------------------------- OWNEKSHIP: AEC/ME3 AEC/MED GOVT GOUT CONTRACTOR CCNTRACTOR

247

Current:  

Office of Legacy Management (LM)

Qwner contacted n yes Qwner contacted n yes Current: ---------------------L---- if yes, date contacted Research & Development cl Facility Type 0 . Productioff 0 Di 3pcsal /Storage TYPE OF CONTRACT ---------------- q Prime q Subcontractor 0 Purchase Order 0 Other information (i.e. q cast + fixed fee, unit piice, time & material, etr) ------- ------_-----_--------------- 0 Production scale testing 0 Pilot Scale 0 Bench Scale Process a Theoretical Studies Sample & Analysis rcc t O' L~1 q Manufacturing 0 University 0 Research Organization 0 Government Sponsored Facility 0 Other ~--~~---_--__-____--- ' Contract/Purchase Order # __-u~-rc,~~--___~~I_IzI__zpI------------ CONTRACTING PE3IOD: lW/ ------------------ _----__--~-~~--~~_-----~~~~~~~~~~~~~~ ClWNERSHIP:

248

Effect of Low Level Direct Current on in Vivo Tumor Growth in Hamsters  

Science Journals Connector (OSTI)

...The treatment current was provided by a battery powered constant current source. The...in tumor mass with treatment was due to thermal effects from heating caused by passage...in these experiments are not caused by thermal factors. It is noted that under our experimental...

Sharon L. David; Darryl R. Absolom; Charles R. Smith; John Gams; and Morley A. Herbert

1985-11-01T23:59:59.000Z

249

Cancer Stem Cells--Perspectives on Current Status and Future Directions: AACR Workshop on Cancer Stem Cells  

E-Print Network [OSTI]

Cancer Stem Cells--Perspectives on Current Status and Future Directions: AACR Workshop on Cancer Hospital for Sick Children, Toronto, Ontario, Canada; 4 Terry Fox Laboratory BC Cancer Research Center, Vancouver, British Columbia, Canada; 5 Moores University of California San Diego Cancer Center; 6 The Salk

Wahl, Geoffrey M.

250

Some Features of an Electrostatic Generator and Ion Source for High Voltage Research  

Science Journals Connector (OSTI)

A compact generator of the Van de Graaff type is described in which several new features have been incorporated. Short-circuit current of one milliampere is available. When operating at 600 kv as voltage supply for accelerating protons or deutersons, 130?a of charged particles at the target have been obtained from an unusual low voltage capillary arc source. In normal operation as a neutron generator, the equivalent of 15 curies of radon-beryllium is readily produced by the reaction Li+D, and 60 curies by the D on D reaction.

I. A. Getting; J. B. Fisk; H. G. Vogt

1939-12-01T23:59:59.000Z

251

Performance Study of K2CsSb Photocathode Inside a DC High Voltage Gun  

SciTech Connect (OSTI)

In the past decade, there has been considerable interest in the generation of tens of mA average current in a photoinjector. Until recently, GaAs:Cs cathodes and K{sub 2}CsSb cathodes have been tested successfully in DC and RF injectors respectively for this application. Our goal is to test the K{sub 2}CsSb photocathode inside a DC gun. Since the multialkali cathode is a compound with constant characteristics over its entire thickness, we anticipate that the lifetime issues seen in GaAs:Cs due to surface damage by ion bombardment would be minimized. Hence successful operation of the K{sub 2}CsSb cathode in a DC gun could lead to a relatively robust electron source capable of delivering ampere level currents. In order to test the performance of a K{sub 2}CsSb cathode in a DC gun, we have designed and built a load lock system that allows the fabrication of the cathode at Brookhaven National Lab (BNL) and its testing at Jefferson Lab (JLab). In this paper, we will present the performance of the K{sub 2}CsSb photocathode in the preparation chamber and in the DC gun.

McCarter J. L.; Rao T.; Smedley, J.; Grames, J.; Mammei, R.; Poelker, M.; Suleiman, R.

2011-09-01T23:59:59.000Z

252

Performance Study of K2CsSb Photocathode inside a DC High Voltage Gun  

SciTech Connect (OSTI)

In the past decade, there has been considerable interest in the generation of tens of mA average current in a photoinjector. Until recently, GaAs:Cs cathodes and K2CsSb cathodes have been tested successfully in DC and RF injectors respectively for this application. Our goal is to test the GaAs:Cs in RF injector and the K2CsSb cathode in the DC gun in order to widen our choices. Since the multialkali cathode is a compound with uniform stochiometry over its entire thickness, we anticipate that the life time issues seen in GaAs:Cs due surface damage by ion bombardment would be minimized with this material. Hence successful operation of the K2CsSb cathode in DC gun could lead to a relatively robust electron source capable of delivering ampere level currents. In order to test the performance of K2CsSb cathode in a DC gun, we have designed and built a load lock system that would allow the fabrication of the cathode at BNL and its testing at JLab. In this paper, we will present the design of the load-lock system, cathode fabrication, and the cathode performance in the preparation chamber and in the DC gun.

T. Rao, J. Smedley, J.M. Grames, R. Mammei, J.L. McCarter, M. Poelker, R. Suleiman

2011-03-01T23:59:59.000Z

253

Direct numerical simulation of electroconvective instability and hysteretic current-voltage response of a permselective membrane  

E-Print Network [OSTI]

We present a systematic, multiscale, fully detailed numerical modeling for dynamics of fluid flow and ion transport covering Ohmic, limiting, and overlimiting current regimes in conductance of ion-selective membrane. By ...

Pham, Van Sang

254

Plasma Immersion Ion Implantation with a 4kV/10kHz Compact High Voltage Pulser  

SciTech Connect (OSTI)

Development of a 4 kV/10 kHz Compact High Voltage Pulser and its application to nitrogen plasma immersion ion implantation (PIII) of different materials as Si, Al alloys, SS304 stainless steel and Ti alloys are discussed. Low voltage (1-5 kV) pulses at high frequencies (up to 20 kHz for 2 kV) were obtained with maximum power delivered at 5 kV, 7 kHz. These conditions were not sufficient to reach temperatures above 200 deg. C in the samples because of short duration of the pulses. However, very shallow implantations of nitrogen in Si, Al5052, SS304 were observed by Auger electron spectroscopy and improved corrosion resistance was obtained for Al5052 when it was treated by nitrogen PIII at 2.5 kV, 5{mu}s and 5 kHz pulses.

Ueda, M.; Oliveira, R. M.; Rossi, J. O. [Associated Laboratory of Plasma, National Institute for Space Research, Av. dos Astronautas 1758, Sao Jose dos Campos, Sao Paulo (Brazil); Reuther, H. [Institute of Ion Beam Physics and Materials Research, Rossendorf, Dresden (Germany); Silva, G. [Associated Laboratory of Plasma, National Institute for Space Research, Av. dos Astronautas 1758, Sao Jose dos Campos, Sao Paulo (Brazil); Department of Aeronautics and Mechanics, Technological Institute of Aeronautics, Sao Jose dos Campos, Sao Paulo (Brazil)

2006-11-13T23:59:59.000Z

255

Electrochemically Stable Cathode Current Collectors for Rechargeable Magnesium Batteries  

SciTech Connect (OSTI)

Rechargeable Mg batteries are attractive energy storage systems and could bring cost-effective energy solutions. Currently, however, no practical cathode current collectors that can withstand high voltages in Mg2+ electrolytes has been identified and therefore cathode research is greatly hindered. Here we identified that two metals, Mo and W, are electrochemically stable through formation of surface passive layers. The presented results could have significant impacts on the developments of high voltage Mg batteries.

Cheng, Yingwen; Liu, Tianbiao L.; Shao, Yuyan; Engelhard, Mark H.; Liu, Jun; Li, Guosheng

2014-01-01T23:59:59.000Z

256

Active electron energy distribution function control in direct current discharge using an auxiliary electrode  

SciTech Connect (OSTI)

The electron energy distribution functions are studied in the low voltage dc discharge with a constriction, which is a diaphragm with an opening. The dc discharge glows in helium and is sustained by the electron current emitted from a heated cathode. We performed kinetic simulations of dc discharge characteristics and electron energy distribution functions for different gas pressures (0.8 Torr-4 Torr) and discharge current of 0.1 A. The results of these simulations indicate the ability to control the shape of the electron energy distribution functions by variation of the diaphragm opening radius.

Schweigert, I. V. [Institute of Theoretical and Applied Mechanics, Novosibirsk 630090 (Russian Federation) [Institute of Theoretical and Applied Mechanics, Novosibirsk 630090 (Russian Federation); George Washington University, Washington, DC 20052 (United States); Kaganovich, I. D. [Princeton Plasma Physics Laboratory, Princeton, NJ 08543 (United States)] [Princeton Plasma Physics Laboratory, Princeton, NJ 08543 (United States); Demidov, V. I. [West Virginia University, Morgantown, WV 26506 (United States) [West Virginia University, Morgantown, WV 26506 (United States); St. Petersburg State University, St. Petersburg (Russian Federation)

2013-10-15T23:59:59.000Z

257

Accelerated Status Exceptionally promising current UCI undergraduate Engineering students may petition for streamlined admission directly  

E-Print Network [OSTI]

Accelerated Status Exceptionally promising current UCI undergraduate Engineering students may numbered 200-289. How to Petition: Students are required to submit an Accelerated Status Petition Form) to the Graduate Student Affairs Office (5400 Engineering Hall). Students may join the Accelerated Status at any

Mease, Kenneth D.

258

Accelerated Status Exceptionally promising current UCI undergraduate Engineering students may petition for streamlined admission directly  

E-Print Network [OSTI]

Accelerated Status Exceptionally promising current UCI undergraduate Engineering students may numbered 200-289. How to Petition: Students are required to submit an Accelerated Status Petition Form) to the Graduate Student Affairs Office (305 Rockwell Engineering Center). Students may join the Accelerated Status

Mease, Kenneth D.

259

Experimental and Numerical Study of Co-ordination of Resistive-Type Superconductor Fault Current Limiter and Relay Protection  

Science Journals Connector (OSTI)

Superconducting fault current limiter (SFCL) has become one of the most ideal current limiting devices to solve the problem of increasing short-circuit current in high-voltage power grid. This paper...

Y. Chen; S. Li; J. Sheng; Z. Jin; Z. Hong…

2013-11-01T23:59:59.000Z

260

A novel direct torque control for induction motor drive system with low torque ripple and current distortion utilising FPGA  

Science Journals Connector (OSTI)

The conventional Direct Torque Control (DTC) is known to produce quick and robust response in ac drives. However, during steady state, notable torque and current pulsations occur. They are reflected in speed estimation, torque response and also produce acoustic noise. In this paper, a novel Space Vector Modulated Direct Torque Control (SVM-DTC) with Low Pass Filter (LPF) for induction motor drive system is proposed, which features low torque ripple, low current distortion and fixed switching frequency. The proposed scheme has been implemented on the Xilinx Spartan 3E FPGA, both simulation and experimental results show that the proposed system can dramatically improve the steady state performance while preserving the dynamic performance of the conventional DTC.

R. Rajendran; N. Devarajan

2013-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "high-voltage direct current" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Direct  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

interactions, and the pollutant emission is hence directly proportional to the bulk neutral density. Simultaneously monitoring the total emission at 1040 nm and the...

262

First-cut design of an all-superconducting 100-T direct current magnet  

SciTech Connect (OSTI)

A 100-T magnetic field has heretofore been available only in pulse mode. This first-cut design demonstrates that a 100-T DC magnet (100?T) is possible. We base our design on: Gadolinium-based coated superconductor; a nested-coil formation, each a stack of double-pancake coils with the no-insulation technique; a band of high-strength steel over each coil; and a 12-T radial-field limit. The 100?T, a 20?mm cold bore, 6-m diameter, 17-m height, with a total of 12?500-km long superconductor, stores an energy of 122 GJ at its 4.2-K operating current of 2400?A. It requires a 4.2-K cooling power of 300?W.

Iwasa, Yukikazu, E-mail: iwasa@jokaku.mit.edu; Hahn, Seungyong [Francis Bitter Magnet Laboratory, Massachusetts Institute of Technology, 170 Albany Street, Cambridge, Massachusetts 02139 (United States)] [Francis Bitter Magnet Laboratory, Massachusetts Institute of Technology, 170 Albany Street, Cambridge, Massachusetts 02139 (United States)

2013-12-16T23:59:59.000Z

263

Silicon-on-insulator-based high-voltage, high-temperature integrated circuit gate driver for silicon carbide-based power field effect transistors  

SciTech Connect (OSTI)

Silicon carbide (SiC)-based field effect transistors (FETs) are gaining popularity as switching elements in power electronic circuits designed for high-temperature environments like hybrid electric vehicle, aircraft, well logging, geothermal power generation etc. Like any other power switches, SiC-based power devices also need gate driver circuits to interface them with the logic units. The placement of the gate driver circuit next to the power switch is optimal for minimising system complexity. Successful operation of the gate driver circuit in a harsh environment, especially with minimal or no heat sink and without liquid cooling, can increase the power-to-volume ratio as well as the power-to-weight ratio for power conversion modules such as a DC-DC converter, inverter etc. A silicon-on-insulator (SOI)-based high-voltage, high-temperature integrated circuit (IC) gate driver for SiC power FETs has been designed and fabricated using a commercially available 0.8--m, 2-poly and 3-metal bipolar-complementary metal oxide semiconductor (CMOS)-double diffused metal oxide semiconductor (DMOS) process. The prototype circuit-s maximum gate drive supply can be 40-V with peak 2.3-A sourcing/sinking current driving capability. Owing to the wide driving range, this gate driver IC can be used to drive a wide variety of SiC FET switches (both normally OFF metal oxide semiconductor field effect transistor (MOSFET) and normally ON junction field effect transistor (JFET)). The switching frequency is 20-kHz and the duty cycle can be varied from 0 to 100-. The circuit has been successfully tested with SiC power MOSFETs and JFETs without any heat sink and cooling mechanism. During these tests, SiC switches were kept at room temperature and ambient temperature of the driver circuit was increased to 200-C. The circuit underwent numerous temperature cycles with negligible performance degradation.

Tolbert, Leon M [ORNL; Huque, Mohammad A [ORNL; Blalock, Benjamin J [ORNL; Islam, Syed K [ORNL

2010-01-01T23:59:59.000Z

264

The effect of a direct current field on the microparticle charge in the plasma afterglow  

SciTech Connect (OSTI)

Residual charges of individual microparticles forming dense clouds were measured in a RF discharge afterglow. Experiments were performed under microgravity conditions on board the International Space Station, which ensured particle levitation inside the gas volume after the plasma switch-off. The distribution of residual charges as well as the spatial distribution of charged particles across the cloud were analyzed by applying a low-frequency voltage to the electrodes and measuring amplitudes of the resulting particle oscillations. Upon “free decharging” conditions, the charge distribution had a sharp peak at zero and was rather symmetric (with charges concentrated between ?10e and +10e), yet positively and negatively charged particles were homogeneously distributed over the cloud. However, when decharging evolved in the presence of an external DC field (applied shortly before the plasma switch-off) practically all residual charges were positive. In this case, the overall charge distribution had a sharp peak at about +15e and was highly asymmetric, while the spatial distribution exhibited a significant charge gradient along the direction of the applied DC field.

Wörner, L. [Max Planck Institute for extraterrestrial Physics, P.O. Box 1312, Giessenbachstr., 85741 Garching (Germany) [Max Planck Institute for extraterrestrial Physics, P.O. Box 1312, Giessenbachstr., 85741 Garching (Germany); Groupe de Recherches sur l'Energétique des Milieux Ionisés, UMR7344, CNRS, Univ. Orléans, F-45067 Orléans (France); Ivlev, A. V.; Huber, P.; Hagl, T.; Thomas, H. M.; Morfill, G. E. [Max Planck Institute for extraterrestrial Physics, P.O. Box 1312, Giessenbachstr., 85741 Garching (Germany)] [Max Planck Institute for extraterrestrial Physics, P.O. Box 1312, Giessenbachstr., 85741 Garching (Germany); Couëdel, L. [Centre National de la Recherche Scientifique, Aix-Marseille-Université, Laboiratoire de Physique des Intéractions Ioniques et Moléculaires, UMR 7345, 13397 Marseille cedex 20 (France)] [Centre National de la Recherche Scientifique, Aix-Marseille-Université, Laboiratoire de Physique des Intéractions Ioniques et Moléculaires, UMR 7345, 13397 Marseille cedex 20 (France); Schwabe, M. [Max Planck Institute for extraterrestrial Physics, P.O. Box 1312, Giessenbachstr., 85741 Garching (Germany) [Max Planck Institute for extraterrestrial Physics, P.O. Box 1312, Giessenbachstr., 85741 Garching (Germany); Department of Chemical and Biomolecular Engineering, University of California, Berkeley, Berkeley, California 94720 (United States); Mikikian, M.; Boufendi, L. [Groupe de Recherches sur l'Energétique des Milieux Ionisés, UMR7344, CNRS, Univ. Orléans, F-45067 Orléans (France)] [Groupe de Recherches sur l'Energétique des Milieux Ionisés, UMR7344, CNRS, Univ. Orléans, F-45067 Orléans (France); Skvortsov, A. [Yuri Gagarin Cosmonauts Training Center, RU-141160 Star City (Russian Federation)] [Yuri Gagarin Cosmonauts Training Center, RU-141160 Star City (Russian Federation); Lipaev, A. M.; Molotkov, V. I.; Petrov, O. F.; Fortov, V. E. [Joint Institute for High Temperatures, RU-125412 Moscow (Russian Federation)] [Joint Institute for High Temperatures, RU-125412 Moscow (Russian Federation)

2013-12-15T23:59:59.000Z

265

Current status, architecture, and future directions for the international space station electric power system  

SciTech Connect (OSTI)

The Electric Power System (EPS) on the International Space Station Alpha has undergone several significant changes over the last year, as major design decisions have been made for the overall station. While the basic topology and system elements have remained as they were under the Freedom program, there are important differences in connectivity, assembly sequence, and start-up. The key drivers for these changes in architecture have been the goal to simplify verification, and most significantly, the introduction of extensive Russian participation in the program. Having the Russians join the international community in this project has resulted in an expanded station size, larger crew, and almost doubled the observable surface of the earth covered by the station. For the power system it has meant additional interfaces for power transfer, and new challenges for solar tracking at the higher inclination orbit. This paper reviews the current architecture and emphasizes the new features that have evolved, as the design for the new, larger station has developed. Additionally, the possible application of developing technology to the station, and other future missions is considered.

Gholdston, E.; Hartung, J.; Friefeld, J. [Rockwell International, Canoga Park, CA (United States). Rocketdyne Division

1995-12-31T23:59:59.000Z

266

EIS-0450: TransWest Express 600 kV Direct Current Transmission Project in Wyoming, Colorado, Utah, and Nevada  

Broader source: Energy.gov [DOE]

This EIS, being prepared jointly by DOE’s Western Area Power Administration and the Department of the Interior’s Bureau of Land Management (Wyoming State Office), evaluates the environmental impacts of granting a right-of-way for the TransWest Express 600-kilovolt Direct Current Transmission Project and amending a land use plan. The project consists of an overhead transmission line that would extend approximately 725 miles from south-central Wyoming, through Colorado and Utah. Western proposes to be a joint owner of the project.

267

Scalable High-Power Redox Capacitors with Aligned Nanoforests of Crystalline MnO2 Nanorods by High Voltage Electrophoretic Deposition  

Science Journals Connector (OSTI)

Scalable High-Power Redox Capacitors with Aligned Nanoforests of Crystalline MnO2 Nanorods by High Voltage Electrophoretic Deposition ... The scalable nanomanufacturing process is demonstrated by roll-printing an aligned forest of ?-MnO2 nanorods on a large flexible substrate (1 inch by 1 foot). ...

Sunand Santhanagopalan; Anirudh Balram; Dennis Desheng Meng

2013-02-01T23:59:59.000Z

268

Theoretical investigation of the effect of hydrogen addition on the formation and properties of soliton in direct current argon plasma  

SciTech Connect (OSTI)

In this study the effect of hydrogen addition on the formation and properties of soliton in direct-current (DC) argon plasma is theoretically investigated. By coupling fluid equations with Poisons equation for such multi-component plasma, the Mach number and amplitude of the soliton are determined following pseudo potential method. Addition of hydrogen in argon discharge leads to the decrease of electron, Ar{sup +} ion density while a reverse trend was observed for ArH{sup +} and hydrogen like ions. It was found that presence of hydrogen like ions in argon plasma affects the formation of soliton with its amplitude significantly decreases as concentration of hydrogen increases. On the other hand, increase in ion to electron temperature ratios of the lighter ions in the discharge also has a significant influence on the amplitude and formation of soliton. The inverse relation between solitons width and amplitude is found to be consistent for the entire range of study.

Saikia, P., E-mail: partha.008@gmail.com; Goswami, K. S.; Saikia, B. K. [Centre of Plasma Physics, Institute for Plasma Research, Nazirakhat, Sonapur, Kamrup, Assam-782 402 (India)] [Centre of Plasma Physics, Institute for Plasma Research, Nazirakhat, Sonapur, Kamrup, Assam-782 402 (India)

2014-03-15T23:59:59.000Z

269

A PC-PCL-based control system for the high-voltage pulsed-power operation of the Intense Diagnostic Neutral Beam (IDNB) Experiment  

SciTech Connect (OSTI)

A stand-alone, semiautomated control system for the high-voltage pulsed-power energy sources on the Intense Diagnostic Neutral Beam Experiment at Los Alamos National Laboratory using personal computer (PC) and programmable logic controller (PLC) technology has been developed and implemented. The control system, consisting of a PC with the graphic operator interface, the network connecting the PC to the PLC, the PLC, the PLC I/O modules, fiber-optic interfaces and software, is described.

Gribble, R.

1993-06-01T23:59:59.000Z

270

Direct and indirect capture of carriers into the lasing ground state and the light-current characteristic of quantum dot lasers  

SciTech Connect (OSTI)

We calculate the light-current characteristic (LCC) of a quantum dot (QD) laser under the conditions of both direct and indirect capture of carriers from the optical confinement layer into the lasing ground state in QDs. We show that direct capture is a dominant process determining the ground-state LCC. Only when direct capture is slow, the role of indirect capture (capture into the QD excited state and subsequent intradot relaxation to the ground state) becomes important.

Wu, Yuchang, E-mail: yuchangw@vt.edu; Asryan, Levon V., E-mail: asryan@vt.edu [Virginia Polytechnic Institute and State University, Blacksburg, Virginia 24061 (United States)

2014-03-14T23:59:59.000Z

271

Comparisons of complex network based models and direct current power flow model to analyze power grid vulnerability under intentional attacks  

Science Journals Connector (OSTI)

Abstract Many scholars have applied complex network based models to investigate power grid vulnerability, but how effective are these models to capture the real performance is an interesting topic. This paper selects two typical complex network based models, including a purely topological model (PTM) and a betweenness based model (BBM), as well as a direct current power flow model (DCPFM), to simulate the topology-based and flow-based vulnerability of power grid under degree, betweenness, maximum traffic and importance based intentional attacks. The relationships of vulnerability results from different models are analyzed and discussed for model comparisons. Taking IEEE 300 power grid with line capacity set proportional to tolerant parameter tp as example, the results show that there exists a critical node attack intensity A I = 0.147 , above which the three models produce almost identical topology-based vulnerability results under each attack strategy at any t p ? 1 , while producing identical flow-based vulnerability results from PTM and DCPFM occurs at A I > 0.147 , and A I > 0.73 for BBM and DCPFM, which indicates that the PTM can better approach the DCPFM for flow-based vulnerability analysis under intentional attacks. Similar results are also found for intentional edge attacks and other power grids.

Min Ouyang; Lijing Zhao; Zhezhe Pan; Liu Hong

2014-01-01T23:59:59.000Z

272

Currents on MDT end plugs  

E-Print Network [OSTI]

A sample of MDT tubes was irradiated in the CERN X5 facility to study their aging behaviour. Part of these tubes were subjected to a glow discharge cleaning (sputtering) with reversed high voltage up to 1660 mC/cm. Current and Ohmic resistance measurements on these tubes gave the same null result as for non-irradiated tubes. The inner plastic surface of one end plug was analysed through the XPS technique. No traces of aluminium were found.

Paschhoff, V

1998-01-01T23:59:59.000Z

273

Comparisons of purely topological model, betweenness based model and direct current power flow model to analyze power grid vulnerability  

Science Journals Connector (OSTI)

This paper selects three frequently used power grid models including a purely topological model (PTM) a betweennness based model (BBM) and a direct current power flow model (DCPFM) to describe three different dynamical processes on a power grid under both single and multiple component failures. Each of the dynamical processes is then characterized by both a topology-based and a flow-based vulnerability metrics to compare the three models with each other from the vulnerability perspective. Taking as an example the IEEE 300 power grid with line capacity set proportional to a tolerance parameter tp the results show non-linear phenomenon: under single node failures there exists a critical value of tp?=?1.36 above which the three models all produce identical topology-based vulnerability results and more than 85% nodes have identical flow-based vulnerability from any two models; under multiple node failures that each node fails with an identical failure probability fp there exists a critical fp?=?0.56 above which the three models produce almost identical topology-based vulnerability results at any tp???1 but producing identical flow-based vulnerability results only occurs at fp?=?1. In addition the topology-based vulnerability results can provide a good approximation for the flow-based vulnerability under large fp and the priority of PTM and BBM to better approach the DCPFM for vulnerability analysis mainly depends on the value of fp. Similar results are also found for other failure types other system operation parameters and other power grids.

2013-01-01T23:59:59.000Z

274

Identifying surface structural changes in layered Li-excess nickel manganese oxides in high voltage lithium ion batteries: A joint experimental and theoretical study  

SciTech Connect (OSTI)

High voltage cathode materials Li-excess layered oxide compounds Li[Ni{sub x}Li{sub 1/3-2x/3}Mn{sub 2/3-x/3}]O{sub 2} (0 < x < 1/2) are investigated in a joint study combining both computational and experimental methods. The bulk and surface structures of pristine and cycled samples of Li[Ni{sub 1/5}Li{sub 1/5}Mn{sub 3/5}]O{sub 2} are characterized by synchrotron X-Ray diffraction together with aberration corrected Scanning Transmission Electron Microscopy (a-S/TEM). Electron Energy Loss Spectroscopy (EELS) is carried out to investigate the surface changes of the samples before/after electrochemical cycling. Combining first principles computational investigation with our experimental observations, a detailed lithium de-intercalation mechanism is proposed for this family of Li-excess layered oxides. The most striking characteristics in these high voltage high energy density cathode materials are (1) formation of tetrahedral lithium ions at voltage less than 4.45 V and (2) the transition metal (TM) ions migration leading to phase transformation on the surface of the materials. We show clear evidence of a new spinel-like solid phase formed on the surface of the electrode materials after high-voltage cycling. It is proposed that such surface phase transformation is one of the factors contributing to the first cycle irreversible capacity and the main reason for the intrinsic poor rate capability of these materials.

Xu, Bo; Fell, Christopher R.; Chi, Miaofang; Meng, Ying Shirley (ORNL); (Florida); (UCSD)

2011-09-06T23:59:59.000Z

275

Experimental investigation of dielectric barrier discharge plasma actuators driven by repetitive high-voltage nanosecond pulses with dc or low frequency sinusoidal bias  

SciTech Connect (OSTI)

Experimental studies were conducted of a flow induced in an initially quiescent room air by a single asymmetric dielectric barrier discharge driven by voltage waveforms consisting of repetitive nanosecond high-voltage pulses superimposed on dc or alternating sinusoidal or square-wave bias voltage. To characterize the pulses and to optimize their matching to the plasma, a numerical code for short pulse calculations with an arbitrary impedance load was developed. A new approach for nonintrusive diagnostics of plasma actuator induced flows in quiescent gas was proposed, consisting of three elements coupled together: the schlieren technique, burst mode of plasma actuator operation, and two-dimensional numerical fluid modeling. The force and heating rate calculated by a plasma model was used as an input to two-dimensional viscous flow solver to predict the time-dependent dielectric barrier discharge induced flow field. This approach allowed us to restore the entire two-dimensional unsteady plasma induced flow pattern as well as characteristics of the plasma induced force. Both the experiments and computations showed the same vortex flow structures induced by the actuator. Parametric studies of the vortices at different bias voltages, pulse polarities, peak pulse voltages, and pulse repetition rates were conducted experimentally. The significance of charge buildup on the dielectric surface was demonstrated. The charge buildup decreases the effective electric field in the plasma and reduces the plasma actuator performance. The accumulated surface charge can be removed by switching the bias polarity, which leads to a newly proposed voltage waveform consisting of high-voltage nanosecond repetitive pulses superimposed on a high-voltage low frequency sinusoidal voltage. Advantages of the new voltage waveform were demonstrated experimentally.

Opaits, Dmitry F.; Likhanskii, Alexandre V.; Neretti, Gabriele; Zaidi, Sohail; Shneider, Mikhail N.; Miles, Richard B. [Mechanical and Aerospace Engineering, Princeton University, Princeton, New Jersey 08544 (United States); Macheret, Sergey O. [Lockheed Martin Aeronautics Company, Palmdale, California 93599 (United States)

2008-08-15T23:59:59.000Z

276

On-line partial discharge monitoring system and data processing using WTST-NST filter for high voltage power cable  

Science Journals Connector (OSTI)

Defects inside insulation of HV XLPE cable accessories can lead to partial discharge (PD) activity. When PD activity happens, leakage current may flow through the grounded line. To acquire the PD current signal, one practicable and effective method is ... Keywords: MRD-MRR algorithm, adaptive WTST-NST filter, condition based maintenance(CBM), on-line monitoring, partial discharge, power cable, stationary noise interference

Hui Wang; Chengjun Huang; Li Zhang; Yong Qian; Junhua Liu; Linpeng Yao; Canxin Guo; Xiuchen Jiang

2009-07-01T23:59:59.000Z

277

Improving the performance of stainless-steel DC high voltage photoelectron gun cathode electrodes via gas conditioning with helium or krypton  

SciTech Connect (OSTI)

Gas conditioning was shown to eliminate field emission from cathode electrodes used inside DC high voltage photoelectron guns, thus providing a reliable means to operate photoguns at higher voltages and field strengths. Measurements and simulation results indicate that gas conditioning eliminates field emission from cathode electrodes via two mechanisms: sputtering and implantation, with the benefits of implantation reversed by heating the electrode. We have studied five stainless steel electrodes (304L and 316LN) that were polished to approximately 20 nm surface roughness using diamond grit, and evaluated inside a high voltage apparatus to determine the onset of field emission as a function of voltage and field strength. The field emission characteristics of each electrode varied significantly upon the initial application of voltage but improved to nearly the same level after gas conditioning using either helium or krypton, exhibiting less than 10 pA field emission at ?225 kV bias voltage with a 50 mm cathode/anode gap, corresponding to a field strength of ~13 MV/m. Field emission could be reduced with either gas, but there were conditions related to gas choice, voltage and field strength that were more favorable than others.

Bastaninejad, Mahzad [ODU; Elmustafa, Abdelmageed [ODU; Forman, Eric I. [JLAB; Clark, James [JLAB; Covert, Steven R. [JLAB; Grames, Joseph M. [JLAB; Hansknecht, John C. [JLAB; Hernandez-Garcia, Carlos [JLAB; Poelker, Bernard [JLAB; Suleiman, Riad S. [JLAB

2014-10-01T23:59:59.000Z

278

Currently, there is a substantial research and development effort directed toward optical signal processing and electronic signal processing for fiber-optic communications. Much of the work  

E-Print Network [OSTI]

Abstract Currently, there is a substantial research and development effort directed toward optical signal processing and electronic signal processing for fiber-optic communications. Much of the work for telecommunication services. For optical signal proc- essing, a variety of approaches are available for implementing

Wu, Shin-Tson

279

Tetrapropyl-tetraphenyl-diindenoperylene derivative as a green absorber for high-voltage stable organic solar cells  

Science Journals Connector (OSTI)

We present small molecule organic solar cells (SMOSC) based on flat heterojunctions (FHJ) of the alternative green donor 2,3,10,11-tetrapropyl-1,4,9,12-tetraphenyl-diindeno[1,2,3-cd:1’,2’,3’-lm]perylene (P4-Ph4-DIP) and the fullerene C60. P4-Ph4-DIP absorbs in the green spectral range and thus fills the spectral gap that standard absorber materials (zinc or copper phthalocyanine for red and C60 for blue absorption) leave, thus allowing broad coverage of the sun spectrum, which is of major interest for tandem devices. The materials properties of P4-Ph4-DIP are studied, and SMOSC are characterized by current voltage, external quantum efficiency, and aging measurements. The solar cells display very high fill factors FF > 76% and open circuit voltages VOC of close to 1 V. Mismatch-corrected efficiencies of up to 1.9% are obtained. Aging measurements show that C60 in conjunction with P4-Ph4-DIP yields extremely stable devices. We observe ? 88% of the initial efficiency after 2500 h illumination at 999 mW/cm2 illumination intensity, with no observable change in short-circuit current density. Furthermore, we also show that a systematic variation of donor thickness in FHJ can be combined with transfer matrix formalism-based optical simulations and the continuity equation for excitons to reliably determine the exciton diffusion length LD. A value of 9 ± 1 nm is found for P4-Ph4-DIP.

Jan Meiss; Martin Hermenau; Wolfgang Tress; Christoph Schuenemann; Franz Selzer; Markus Hummert; Joerg Alex; Gerhard Lackner; Karl Leo; Moritz Riede

2011-04-11T23:59:59.000Z

280

RECIPIENT:Princeton Power Systems STATE: NJ PROJECT Marine High-Voltage Power Conditioning and Transmission System with Integrated Energy Storage  

Broader source: Energy.gov (indexed) [DOE]

Princeton Power Systems Princeton Power Systems STATE: NJ PROJECT Marine High-Voltage Power Conditioning and Transmission System with Integrated Energy Storage TITLE: Funding Opportunity Announcement Number Procurement Instrument Number NEPA Control Number cm Number DE-FOA-0000293 DE-EE0003640 GFO-000364~001 GOO Based on my review of the information concerning the proposed action, as NEPA Compliance Officer (authorized under DOE Order 451.1A), I have made the foUowing determination: CX, EA, EIS APPENDIX AND NUMBER: Description: A9 Information gathering (including, but not limited to, ~terature surveys, inventories, audits), data analysis (including computer modeling), document preparation (such as conceptual design or feasibility studies, analytical energy supply

Note: This page contains sample records for the topic "high-voltage direct current" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Pulsed CO{sub 2} laser with an X-ray preioniser based on a high-voltage low-pressure glow discharge  

SciTech Connect (OSTI)

An X-ray preioniser with an electron beam energy density of 0.1 J cm{sup -2} based on a high-voltage (20 - 40 kV) low-pressure glow discharge is developed for repetitively pulsed gas lasers. The electron concentration in the CO{sub 2} - N{sub 2} - He mixture as a function of the voltage across the preioniser is calculated for titanium and other foils. The preioniser can be operated both in a single-pulse regime and at pulse repetition rates ranging up to hundreds of Hertz. A specific energy yield of 51 J L{sup -1} is achieved in the X-ray preionised pulsed CO{sub 2} atmospheric-pressure laser. This preioniser was shown to be efficient for other active media (CO and excimer lasers), which opens up new opportunities for the development of repetitively pulsed gas lasers. (lasers)

Oreshkin, V F; Seregin, Aleksandr M; Sinaiskii, V V; Shchetinkina, T A ['Astrofizika' Research and Production Association (Russian Federation); Sorokin, A R [Institute of Semiconductor Physics, Siberian Branch of the Russian Academy of Sciences, Novosibirsk (Russian Federation)

2003-12-31T23:59:59.000Z

282

Abstract--Circuit breakers are crucial components for power system operation. The currently adapted time-directed  

E-Print Network [OSTI]

1 Abstract--Circuit breakers are crucial components for power system operation. The currently be This work was supported in part by Mitsubishi Electric Research Laboratories and PSerc consortium, an NSF I used to select the most appropriate maintenance strategy. During the maintenance or repair work

283

A wide bandgap silicon carbide (SiC) gate driver for high-temperature and high-voltage applications  

SciTech Connect (OSTI)

Limitations of silicon (Si) based power electronic devices can be overcome with Silicon Carbide (SiC) because of its remarkable material properties. SiC is a wide bandgap semiconductor material with larger bandgap, lower leakage currents, higher breakdown electric field, and higher thermal conductivity, which promotes higher switching frequencies for high power applications, higher temperature operation, and results in higher power density devices relative to Si [1]. The proposed work is focused on design of a SiC gate driver to drive a SiC power MOSFET, on a Cree SiC process, with rise/fall times (less than 100 ns) suitable for 500 kHz to 1 MHz switching frequency applications. A process optimized gate driver topology design which is significantly different from generic Si circuit design is proposed. The ultimate goal of the project is to integrate this gate driver into a Toyota Prius plug-in hybrid electric vehicle (PHEV) charger module. The application of this high frequency charger will result in lighter, smaller, cheaper, and a more efficient power electronics system.

Lamichhane, Ranjan [University of Arkansas; Ericson, Milton Nance [ORNL; Frank, Steven Shane [ORNL; BRITTONJr., CHARLES L. [Oak Ridge National Laboratory (ORNL); Marlino, Laura D [ORNL; Mantooth, Alan [University of Arkansas; Francis, Matt [APEI, Inc.; Shepherd, Dr. Paul [University of Arkansas; Glover, Dr. Michael [University of Arkansas; Podar, Mircea [ORNL; Perez, M [University of Arkansas; Mcnutt, Tyler [APEI, Inc.; Whitaker, Mr. Bret [APEI, Inc.; Cole, Mr. Zach [APEI, Inc.

2014-01-01T23:59:59.000Z

284

Superconducting fault-current limiter and inductor design  

SciTech Connect (OSTI)

A superconducting fault current limiter (SFCL) that uses a biased superconducting inductor in a diode or thyristor bridge circuit was analyzed for transmission systems in 69, 138, and 230 rms kV utility transmission systems. The limiter was evaluated for costs with all components - superconducting coil, diode and/or SCR power electronics, high voltage insulation, high voltage bushings and vapor cooled leads, dewar, and refrigerator - included. A design was undertaken for the superconducting cable and coils for both diode and SCR 69 kV limiter circuits.

Rogers, J.D.; Boenig, H.J.; Chowdhuri, P.; Schermer, R.I.; Wollan, J.J.; Weldon, D.M.

1982-01-01T23:59:59.000Z

285

Lightweight PV Inverters: Dual Bi-Directional IGBTs Modules Enables Breakthrough PV Inverter Using Current Modulation Topology  

SciTech Connect (OSTI)

Solar ADEPT Project: PV inverters convert DC power generated by modules into usable AC power. IPC’s initial 30kW 94lb. PV inverter reduces the weight of comparable 30kW PV inverters by 90%—reducing the cost of materials, manufacturing, shipping, and installation. With ARPA-E support, new bi-directional silicon power switches will be developed, commercialized, and utilized in IPC’s next-generation PV inverter. With these components, IPC will produce 100kW inverters that weight less than 100lb., reducing the weight of conventional 3,000lb. 100kW inverters by more than 95%. The new power switches will cut IPC’s $/W manufacturing cost in half, as well as further reduce indirect shipping and installation costs.

None

2012-01-30T23:59:59.000Z

286

Exposure information in environmental health research: Current opportunities and future directions for particulate matter, ozone, and toxic air pollutants  

SciTech Connect (OSTI)

Understanding and quantifying outdoor and indoor sources of human exposure are essential but often not adequately addressed in health-effects studies for air pollution. Air pollution epidemiology, risk assessment, health tracking and accountability assessments are examples of health-effects studies that require but often lack adequate exposure information. Recent advances in exposure modeling along with better information on time-activity and exposure factors data provide us with unique opportunities to improve the assignment of exposures for both future and ongoing studies linking air pollution to health impacts. In September 2006, scientists from the US Environmental Protection Agency (EPA) and the Centers for Disease Control and Prevention (CDC) along with scientists from the academic community and state health departments convened a symposium on air pollution exposure and health in order to identify, evaluate, and improve current approaches for linking air pollution exposures to disease. This manuscript presents the key issues, challenges and recommendations identified by the exposure working group, who used cases studies of particulate matter, ozone, and toxic air pollutant exposure to evaluate health-effects for air pollution. One of the over-arching lessons of this workshop is that obtaining better exposure information for these different health-effects studies requires both goal-setting for what is needed and mapping out the transition pathway from current capabilities to meeting these goals. Meeting our long-term goals requires definition of incremental steps that provide useful information for the interim and move us toward our long-term goals. Another over-arching theme among the three different pollutants and the different health study approaches is the need for integration among alternate exposure assessment approaches. For example, different groups may advocate exposure indicators, biomonitoring, mapping methods (GIS), modeling, environmental media monitoring, and/or personal exposure modeling. However, emerging research reveals that the greatest progress comes from integration among two or more of these efforts.

McKone, Thomas E.; Ryan, P. Barry; Ozkaynak, Haluk

2007-02-01T23:59:59.000Z

287

Transmission investment and expansion planning in a restructured electricity market  

E-Print Network [OSTI]

such as phase shifting transformers (PST), high-voltage direct-current (HVDC) lines, and other power

Leung, Ka-Cheong

288

High-Voltage Test Laboratories  

Science Journals Connector (OSTI)

The power for a complete HV laboratory is usually supplied from a medium-...9.20...). One or several three-phase distribution transformers in a nearby substation should be used for that purpose. Their...Sect. 9.2...

Wolfgang Hauschild; Eberhard Lemke

2014-01-01T23:59:59.000Z

289

Fault current limiter using a series impedance combined with bus sectionalizing circuit breaker  

Science Journals Connector (OSTI)

The necessity and procedure for application of series fault current limiter (FCL) composed to bus sectionalizing in power network of IRAN have been discussed. In this regard, all of the high voltage substations in the power network of IRAN were evaluated in point of view of the fault current amplitude. The short circuit analysis of the power network was done based on the actual and future network specifications which have been designed and published by Iran Generation Transmission & Distribution Company in 2005. The overall results of this analysis and the detail data of using FCL together bus sectionalizing for two of the most important high voltage substations of Iran are presented. This method allows decreasing of 27% in fault current amplitude. The economical observation shows this method can be profitable if high voltage substation contains more than four feeders.

Hamid Javadi

2011-01-01T23:59:59.000Z

290

Effect of the change in the load resistance on the high voltage pulse transformer of the intense electron-beam accelerators  

SciTech Connect (OSTI)

A high voltage pulse transformer (HVPT) is usually used as a charging device for the pulse forming line (PFL) of intense electron-beam accelerators (IEBAs). Insulation of the HVPT is one of the important factors that restrict the development of the HVPT. Until now, considerable effort has been focused on minimizing high field regions to avoid insulation breakdown between windings. Characteristics of the HVPT have been widely discussed to achieve these goals, but the effects of the PFL and load resistance on HVPT are usually neglected. In this paper, a HVPT is used as a charging device for the PFL of an IEBA and the effect of the change in the load resistance on the HVPT of the IEBA is presented. When the load resistance does not match the wave impedance of the PFL, a high-frequency bipolar oscillating voltage will occur, and the amplitude of the oscillating voltage will increase with the decrease in the load resistance. The load resistance approximates to zero and the amplitude of the oscillating voltage is much higher. This makes it easier for surface flashover along the insulation materials to form and decrease the lifetime of the HVPT.

Cheng Xinbing; Liu Jinliang; Qian Baoliang; Zhang Yu; Zhang Hongbo [College of Photoelectrical Science and Engineering, National University of Defense Technology, Hunan 410073 (China)

2009-11-15T23:59:59.000Z

291

Low resistivity Ga-doped ZnO thin films of less than 100 nm thickness prepared by ion plating with direct current arc discharge  

SciTech Connect (OSTI)

Low resistivity Ga-doped ZnO films were prepared on a glass substrate by ion plating with direct current arc discharge. Thickness dependent changes in the electrical properties of the films are reported, focusing on the thin films of less than 100 nm thickness. Structural analyses showed that the thinnest film of 30 nm thickness consists of well-oriented columnar grains normal to the substrate, and the resistivity was as low as 4.4x10{sup -4} {omega} cm. The changes in lattice strain and c-axis fluctuation with the growth of grains are also shown to be associated with the electrical properties.

Yamada, Takahiro; Miyake, Aki; Kishimoto, Seiichi; Makino, Hisao; Yamamoto, Naoki; Yamamoto, Tetsuya [Kochi University of Technology, 185, Miyanokuchi, Tosayamada, Kami, Kochi 782-8502 (Japan)

2007-07-30T23:59:59.000Z

292

Measurements of the volt-ampere characteristics and the breakdown voltages of direct-current helium and hydrogen discharges in microgaps  

SciTech Connect (OSTI)

The discharge phenomena for micro meter gap sizes include many interesting problems from engineering and physical perspectives. In this paper, the authors deal with the experimental and theoretical results of the breakdown voltage and current-voltage characteristics of the direct-current helium and hydrogen discharges. The measurements were performed at a constant pressure of around one atmosphere, while varying the gap size between two parallel plane tungsten electrodes between 1??m and 100??m. From the measured breakdown voltage curves, the effective yields and the ionization coefficients were derived for both gases. Present data for the ionization coefficients correlate with the data obtained for the breakdown voltage curves measured for fixed 100??m interelectrode separation. The current-voltage characteristics were plotted for the various gap sizes illustrating the role of the field emission effects in the microgaps. Based on the Fowler-Nordheim theory, the enhancement factors were determined. The gap spacing dependence of the field emission current can be explained by the introduction of two ideas, the first being a space charge effect by emitted electrons, and the second a change in the breakdown mechanism. Experimental results, presented here, demonstrate that Townsend phenomenology breaks down when field emission becomes the key mechanism affecting the breakdown and deforming the left hand side of the breakdown voltage curves.

Klas, M.; Matej?ik, Š. [Department of Experimental Physics, Comenius University, Mlynskadolina F2, 84248 Bratislava (Slovakia); Radjenovi?, B.; Radmilovi?-Radjenovi?, M. [Institute of Physics, University of Belgrade, P.O. Box 57, 11080 Belgrade (Serbia)

2014-10-15T23:59:59.000Z

293

OMNI SMARTPUMP: DIRECT CURRENT POWERED  

E-Print Network [OSTI]

completed grant projects. The purpose of the FAR is to provide a concise summary and independent assessment Program, please visit the Commission's Web site at http://www.energy.ca.gov/research/index.html. #12;Page

294

Direct current power transmission systems  

SciTech Connect (OSTI)

This book represents text on HVDC transmission available. It deals with the various aspects of the state of the art in HVDC transmission technology. This book presents many aspects of interactions of AC/DC systems. Modeling and analysis of DC systems are also discussed in detail.

Padiyar, K.R.

1991-01-01T23:59:59.000Z

295

Measurement of critical energy for direct initiation of spherical detonations in stoichiometric high-pressure H{sub 2}-O{sub 2} mixtures  

SciTech Connect (OSTI)

In this study, the critical energy for direct initiation of spherical detonations in stoichiometric high-pressure hydrogen-oxygen mixtures are measured and investigated to look at the effect of explosion limits on the detonation sensitivity. Results up to an initial pressure of 20 atm are obtained. Experiments are carried out in a spherical bomb and direct initiation is achieved via spark ignition from a high-voltage capacitor discharge. A detailed description of different methods to obtain a good estimate of the correct amount of energy deposited into the mixture used to initiate the detonation, including the calorimeter method and current method, is provided. It is demonstrated that at elevated initial pressure, the second explosion limit effect plays a significant role leading to slow-branching reactions and the detonation sensitivity of hydrogen mixtures is comparable to other common hydrocarbon mixtures at such condition. (author)

Kamenskihs, Vsevolods; Lee, John H.S. [Department of Mechanical Engineering, McGill University, Montreal, Quebec (Canada); Ng, Hoi Dick [Department of Mechanical and Industrial Engineering, Concordia University, Montreal, Quebec (Canada)

2010-09-15T23:59:59.000Z

296

Dielectric-wall linear accelerator with a high voltage fast rise time switch that includes a pair of electrodes between which are laminated alternating layers of isolated conductors and insulators  

DOE Patents [OSTI]

A dielectric-wall linear accelerator is improved by a high-voltage, fast rise-time switch that includes a pair of electrodes between which are laminated alternating layers of isolated conductors and insulators. A high voltage is placed between the electrodes sufficient to stress the voltage breakdown of the insulator on command. A light trigger, such as a laser, is focused along at least one line along the edge surface of the laminated alternating layers of isolated conductors and insulators extending between the electrodes. The laser is energized to initiate a surface breakdown by a fluence of photons, thus causing the electrical switch to close very promptly. Such insulators and lasers are incorporated in a dielectric wall linear accelerator with Blumlein modules, and phasing is controlled by adjusting the length of fiber optic cables that carry the laser light to the insulator surface. 12 figs.

Caporaso, G.J.; Sampayan, S.E.; Kirbie, H.C.

1998-10-13T23:59:59.000Z

297

Self consistent radio-frequency wave propagation and peripheral direct current plasma biasing: Simplified three dimensional non-linear treatment in the 'wide sheath' asymptotic regime  

SciTech Connect (OSTI)

A minimal two-field fluid approach is followed to describe the radio-frequency (RF) wave propagation in the bounded scrape-off layer plasma of magnetic fusion devices self-consistently with direct current (DC) biasing of this plasma. The RF and DC parts are coupled by non-linear RF and DC sheath boundary conditions at both ends of open magnetic field lines. The physical model is studied within a simplified framework featuring slow wave (SW) only and lateral walls normal to the straight confinement magnetic field. The possibility is however kept to excite the system by any realistic 2D RF field map imposed at the outer boundary of the simulation domain. The self-consistent RF + DC system is solved explicitly in the asymptotic limit when the width of the sheaths gets very large, for several configurations of the RF excitation and of the target plasma. In the case of 3D parallelepipedic geometry, semi-analytical results are proposed in terms of asymptotic waveguide eigenmodes that can easily be implemented numerically. The validity of the asymptotic treatment is discussed and is illustrated by numerical tests against a quantitative criterion expressed from the simulation parameters. Iterative improvement of the solution from the asymptotic result is also outlined. Throughout the resolution, key physical properties of the solution are presented. The radial penetration of the RF sheath voltages along lateral walls at both ends of the open magnetic field lines can be far deeper than the skin depth characteristic of the SW evanescence. This is interpreted in terms of sheath-plasma wave excitation. Therefore, the proper choice of the inner boundary location is discussed as well as the appropriate boundary conditions to apply there. The asymptotic scaling of various quantities with the amplitude of the input RF excitation is established.

Colas, L.; Jacquot, J.; Hillairet, J.; Goniche, M. [CEA, IRFM, F-13108 Saint-Paul-lez-Durance (France); Heuraux, S.; Faudot, E. [IJL-P2M UMR 7198 CNRS, F-54506 Vandoeuvre les Nancy (France); Crombe, K. [Department of Applied Physics, Ghent University, B-9000 Ghent (Belgium); Kyrytsya, V. [LPP-ERM/KMS, Association Euratom-'Belgian State', TEC Partner, Brussels (Belgium)

2012-09-15T23:59:59.000Z

298

Electric Currents Electric Current  

E-Print Network [OSTI]

coefficient of resistivity Electric Power: = = = Also, = . So, = = 2 = 2 Unit of Power(P): Watt (WChapter 18 Electric Currents #12;Electric Current: Flow of electric charge Current is flow of positive charge. In reality it's the electron moves in solids- Electron current. #12;Ohm's Law : Resistance

Yu, Jaehoon

299

The high current, fast, 100ns, Linear Transformer Driver (LTD) developmental project at Sandia National Laboratories.  

SciTech Connect (OSTI)

Sandia National Laboratories, Albuquerque, N.M., USA, in collaboration with the High Current Electronic Institute (HCEI), Tomsk, Russia, is developing a new paradigm in pulsed power technology: the Linear Transformer Driver (LTD) technology. This technological approach can provide very compact devices that can deliver very fast high current and high voltage pulses straight out of the cavity with out any complicated pulse forming and pulse compression network. Through multistage inductively insulated voltage adders, the output pulse, increased in voltage amplitude, can be applied directly to the load. The load may be a vacuum electron diode, a z-pinch wire array, a gas puff, a liner, an isentropic compression load (ICE) to study material behavior under very high magnetic fields, or a fusion energy (IFE) target. This is because the output pulse rise time and width can be easily tailored to the specific application needs. In this paper we briefly summarize the developmental work done in Sandia and HCEI during the last few years, and describe our new MYKONOS Sandia High Current LTD Laboratory.

Ward, Kevin S.; Long, Finis W.; Sinebryukhov, Vadim A. (High Current Electronic Institute (HCEI), Tomsk, Russia); Kim, Alexandre A. (High Current Electronic Institute (HCEI), Tomsk, RUSSIA); Wakeland, Peter Eric (Ktech Corporation, Albuquerque, NM); McKee, G. Randall; Woodworth, Joseph Ray; McDaniel, Dillon Heirman; Fowler, William E.; Mazarakis, Michael Gerrassimos; Porter, John Larry, Jr.; Struve, Kenneth William; Stygar, William A.; LeChien, Keith R.; Matzen, Maurice Keith

2010-04-01T23:59:59.000Z

300

Restoration and testing of an HTS fault current controller  

SciTech Connect (OSTI)

A three-phase, 1200 A, 12.5 kV fault current controller using three HTS 4 mH coils, was built by industry and tested in 1999 at the Center Substation of Southern California Edison in Norwalk, CA. During the testing, it appeared that each of the three single-phase units had experienced a voltage breakdown, one externally and two internally. Los Alamos National Laboratory (LANL) was asked by DOE to restore the operation of the fault current controller provided the HTS coils had not been damaged during the initial substation tests. When the internally-failed coil vacuum vessels were opened it became evident that in these two vessels, a flashover had occurred at the high voltage bus section leading to the terminals of the superconducting coil. An investigation into the failure mechanism resulted in six possible causes for the flashover. Based on these causes, the high voltage bus was completely redesigned. Single-phase tests were successfully performed on the modified unit at a 13.7 kV LANL substation. This paper presents the postulated voltage flashover failure mechanisms, the new high voltage bus design which mitigates the failure mechanisms, the sequence of tests used to validate the new design, and finally, the results of variable load and short-circuit tests with the single-phase unit operating on the LANL 13.7 kV substation.

Waynert, J. A. (Joseph A.); Boenig, H. (Heinrich E.); Mielke, C. H. (Charles H.); Willis, J. O. (Jeffrey O.); Burley, B. L. (Burt L.)

2002-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "high-voltage direct current" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Notices  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

in Oklahoma and Tennessee; an approximately 720- mile high voltage direct current (HVDC) transmission line; an alternating current (AC) collection system; and access roads. This...

302

Offshore Wind Park Connection to an HVDC Platform, without using an AC Collector Platform.  

E-Print Network [OSTI]

?? This thesis investigates the comparison between two different alternating current topologies of an offshore wind farms connection to an offshore high voltage direct current… (more)

Ahmad, Haseeb

2012-01-01T23:59:59.000Z

303

Trace Analysis and Speciation for Cr(VI) and Cr(III) via HPLC-Direct Current Plasma Emission Spectroscopy (HPLC-DCP)  

Science Journals Connector (OSTI)

......chromium content, and were then free/e-dried prior to storage and preservation. It was this freeze-dried material that...current interests in possible chromium levels to be found in seawater and/or biological samples taken from the Georges Bank area......

I.S. Krull; K.W. Panaro; L.L. Gershman

1983-10-01T23:59:59.000Z

304

Current Status  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Current Status Current Status > Content on this page requires a newer version of Adobe Flash Player. Get Adobe Flash player July 31, 1942 The Army Corp of Engineers leases 1,025 acres of the Cook County Forest Preserve to build a research facility. November 1942 Under the direction of Enrico Fermi, a group of scientists at the University of Chicago begin building Chicago Pile-1 (CP-1). Security and secracy were essential. December 2, 1942 Enrico Fermi's team creates the world's first self-sustaining nuclear chain reaction using the CP-1 reactor under Stagg Field at the University of Chicago. CP-1 1943 The experiments under Stagg Field shut down, and the scientists move to a 19 acre section of the leased forest preserve, known as Site A. CP-1 is reconstructed and modified at Site A and renamed Chicago Pile 2 (CP-2).

305

Theoretical investigation of direct and phonon-assisted tunneling currents in InAlGaAs/InGaAs bulk and quantum-well interband tunnel junctions for multijunction solar cells  

Science Journals Connector (OSTI)

Direct and phonon-assisted tunneling currents in InAlGaAs-InGaAs bulk and double-quantum-well interband tunnel heterojunctions are simulated rigorously using the nonequilibrium Green's function formalism for coherent and dissipative quantum transport in combination with a simple two-band tight-binding model for the electronic structure. A realistic band profile and the associated built-in electrostatic field are obtained via self-consistent coupling of the transport formalism to Poisson's equation. The model reproduces experimentally observed features in the current-voltage characteristics of the devices, such as the pronounced current enhancement in the quantum-well junction as compared to the bulk junction and the structure appearing in the negative-differential resistance regime due to quantization of emitter states. Local maps of density of states and the current spectrum reveal the impact of quasibound states, electric fields, and electron-phonon scattering on the interband tunneling current. In this way, resonances appearing in the current through the double-quantum-well structure in the negative-differential resistance regime can be related to the alignment of subbands in the coupled quantum wells.

U. Aeberhard

2013-02-05T23:59:59.000Z

306

IEEE Applied Power Elecb"onics Confererice (APEC '93) Record, pp. 58-64, San Diego, March 1993. Current-Fed Multi-Resonant DC-DC Converter  

E-Print Network [OSTI]

.: +(972) 57461-561; FAX: +(972) 57281-340; Email: SBY@BGUEE.BI1NET Department of ElecUical and Computer at the output, a high voltage gain and zero voltage switching over a iarge range of output voitage against short circuit at the output while maintaining Zero Voltage Switching (ZVS) or Zero Current

307

Home: Directives, Delegations, and Requirements  

Broader source: All U.S. Department of Energy (DOE) Office Webpages

content. | Skip to navigation content. | Skip to navigation Site Map Contact Us Current Documents Archived Documents Entire Site only in current section Advanced Search... U.S. Department of Energy Office of Management Directives, Delegations, and Requirements Sections Home Directives Current Directives Draft Directives Archives Delegations Current Delegations Current Designations Rescinded Organizations' Assignment of Responsibility Development & Review RevCom Writers' Tools DPC Corner References News and Updates Help Personal tools You are here: Office of Management » Directives, Delegations, and Requirements Info Home Directives are the Department of Energy's primary means of establishing policies, requirements, responsibilities, and procedures for Departmental elements and contractors. Directive

308

Modelling and control of multi-terminal HVDC networks for offshore wind power generation.  

E-Print Network [OSTI]

??Due to the recent developments in semiconductors and control equipment, Voltage Source Converter based High Voltage Direct Current (VSC-HVDC) becomes a promising technology for grid… (more)

Zhou, Shu

2011-01-01T23:59:59.000Z

309

EIS-0486: DOE Notice of Availability of Draft Environmental Impact...  

Office of Environmental Management (EM)

project would include an overhead 600 kilovolt (kV) high voltage direct current (HVDC) electric transmission system and associated facilities with the capacity to deliver...

310

Application for presidential permit OE Docket No. PP-371 Northern...  

Broader source: Energy.gov (indexed) [DOE]

for a Presidential Permit to construct a 1,200 MW high voltage direct current ("HVDC") transmission line (the "Application") from the Des Cantons substation in Quebec, to...

311

Optically initiated silicon carbide high voltage switch  

DOE Patents [OSTI]

An improved photoconductive switch having a SiC or other wide band gap substrate material, such as GaAs and field-grading liners composed of preferably SiN formed on the substrate adjacent the electrode perimeters or adjacent the substrate perimeters for grading the electric fields.

Caporaso, George J. (Livermore, CA); Sampayan, Stephen E. (Manteca, CA); Sullivan, James S. (Livermore, CA); Sanders; David M. (Livermore, CA)

2011-02-22T23:59:59.000Z

312

HIGH-VOLTAGE SPINEL AND POLYANION CATHODES  

Broader source: Energy.gov (indexed) [DOE]

POLYANION CATHODES ARUMUGAM MANTHIRAM Electrochemical Energy Laboratory (ECEL) Materials Science and Engineering Program The University of Texas at Austin May 14, 2012 Project ID...

313

Lockout device for high voltage circuit breaker  

SciTech Connect (OSTI)

An improved lockout assembly is provided for a circuit breaker to lock the switch handle into a selected switch position. The lockout assembly includes two main elements, each having a respective foot for engaging a portion of the upper housing wall of the circuit breaker. The first foot is inserted into a groove in the upper housing wall, and the second foot is inserted into an adjacent aperture (e.g., a slot) in the upper housing wall. The first foot is slid under and into engagement with a first portion, and the second foot is slid under and into engagement with a second portion of the upper housing wall. At the same time the respective two feet are placed in engagement with the respective portions of the upper housing wall, two holes, one on each of the respective two main elements of the assembly, are placed in registration; and a locking device, such as a special scissors equipped with a padlock, is installed through the registered holes to secure the lockout assembly on the circuit breaker. When the lockout assembly of the invention is secured on the circuit breaker, the switch handle of the circuit breaker is locked into the selected switch position and prevented from being switched to another switch position.

Kozlowski, L.J.; Shirey, L.A.

1993-01-26T23:59:59.000Z

314

Lockout device for high voltage circuit breaker  

DOE Patents [OSTI]

An improved lockout assembly is provided for a circuit breaker to lock the switch handle into a selected switch position. The lockout assembly includes two main elements, each having a respective foot for engaging a portion of the upper housing wall of the circuit breaker. The first foot is inserted into a groove in the upper housing wall, and the second foot is inserted into an adjacent aperture (e.g., a slot) in the upper housing wall. The first foot is slid under and into engagement with a first portion, and the second foot is slid under and into engagement with a second portion of the upper housing wall. At the same time the repsective two feet are placed in engagement with the respective portions of the upper housing wall, two holes, one on each of the respective two main elements of the assembly, are placed in registration; and a locking device, such as a special scissors equipped with a padlock, is installed through the registered holes to secure the lockout assembly on the circuit breaker. When the lockout assembly of the invention is secured on the circuit breaker, the switch handle of the circuit breaker is locked into the selected switch position and prevented from being switched to another switch position.

Kozlowski, Lawrence J. (New Kensington, PA); Shirey, Lawrence A. (North Huntingdon, PA)

1993-01-01T23:59:59.000Z

315

Lookout device for high voltage circuit breaker  

SciTech Connect (OSTI)

An improved lockout assembly is provided for a circuit breaker to lock the switch handle into a selected switch position. The lockout assembly includes two main elements, each having a respective foot for engaging a portion of the upper housing wall of the circuit breaker. The first foot is inserted into a groove in the upper housing wall, and the second foot is inserted into an adjacent aperture (e.g., a slot) in the upper housing wall. The first foot is slid under and into engagement with a first portion, and the second foot is slid under and into engagement with a second portion of the upper housing wall. At the same time the respective two feet are placed in engagement with the respective portions of the upper housing wall, two holes, one on each of the respective two main elements of the assembly, are placed in registration; and a locking device, such as a special scissors equipped with a padlock, is installed through the registered holes to secure the lockout assembly on the circuit breaker. When the lockout assembly of the invention is secured on the circuit breaker, the switch handle of the circuit breaker is locked into the selected switch position and prevented from being switched to another switch position.

Kozlowski, L.J.; Shirey, L.A.

1991-12-31T23:59:59.000Z

316

High Voltage Power Supply Capacitor Problem Analysis  

E-Print Network [OSTI]

evidence of pits on the surface. One pit showed evidence that the silver had burned thru. It was concluded this was the shorted area.. A microsection of the capacitor (see photomicrograph #1} shows a pit in the dielectric material. Photomicrograph #2 shows another pit in the same capacitor. 2. 3 A total of eighteen capacitors

Rathbun, Julie A.

317

Production of high voltage by ion bombardment  

E-Print Network [OSTI]

E-08 2000 0. 511 1999. 489 5. 120E-08 0. 539 1999. 461 5. 401E-08 2500 O. B39 2499. 361 6. 403E-DB 0. 675 2499. 325 6. 764E-DB 3000 0. 769 2999. 231 7. 705E-OB 0. 810 2999. 190 8. 116E-OB 3500 0. 899 3499. 101 9. 008E-OB 0. 948 3499. 054 9. 479E...E-08 2000 0. 511 1999. 489 5. 120E-08 0. 539 1999. 461 5. 401E-08 2500 O. B39 2499. 361 6. 403E-DB 0. 675 2499. 325 6. 764E-DB 3000 0. 769 2999. 231 7. 705E-OB 0. 810 2999. 190 8. 116E-OB 3500 0. 899 3499. 101 9. 008E-OB 0. 948 3499. 054 9. 479E...

Phinney, Lucas Carter

2012-06-07T23:59:59.000Z

318

HIGH-VOLTAGE SPINEL AND POLYANION CATHODES  

Broader source: Energy.gov [DOE]

2012 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting

319

A Radiofrequency High-Voltage Generator  

Science Journals Connector (OSTI)

A large radio oscillator with unrectified alternating anode power-supply sends high-frequency power into a 50 meter wave-length antenna which is coiled up without insulation, and enclosed in a metal vacuum tank. Over 800,000 volts is generated inside of the tank exactly where it is to be used for x-rays or for accelerating ions. There is no insulation to become punctured. Single tuned-circuit resonance transformers are superior to coupled tuned-circuit Tesla coils. Resonance transformers, oscillator circuits, power tubes, power supply and coil construction are described. X-ray production, and ion acceleration are outlined.

David H. Sloan

1935-01-01T23:59:59.000Z

320

Electro-optic high voltage sensor  

DOE Patents [OSTI]

A small sized electro-optic voltage sensor capable of accurate measurement of high levels of voltages without contact with a conductor or voltage source is provided. When placed in the presence of an electric field, the sensor receives an input beam of electromagnetic radiation into the sensor. A polarization beam displacer serves as a filter to separate the input beam into two beams with orthogonal linear polarizations. The beam displacer is oriented in such a way as to rotate the linearly polarized beams such that they enter a Pockels crystal having at a preferred angle of 45 degrees. The beam displacer is therefore capable of causing a linearly polarized beam to impinge a crystal at a desired angle independent of temperature. The Pockels electro-optic effect induces a differential phase shift on the major and minor axes of the input beam as it travels through the Pockels crystal, which causes the input beam to be elliptically polarized. A reflecting prism redirects the beam back through the crystal and the beam displacer. On the return path, the polarization beam displacer separates the elliptically polarized beam into two output beams of orthogonal linear polarization representing the major and minor axes. The system may include a detector for converting the output beams into electrical signals, and a signal processor for determining the voltage based on an analysis of the output beams. The output beams are amplitude modulated by the frequency of the electric field and the amplitude of the output beams is proportional to the magnitude of the electric field, which is related to the voltage being measured.

Davidson, James R. (Idaho Falls, ID); Seifert, Gary D. (Idaho Falls, ID)

2002-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "high-voltage direct current" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

High Voltage Electrolyte for Lithium Batteries  

Broader source: Energy.gov [DOE]

2012 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting

322

Electrical system architecture having high voltage bus  

DOE Patents [OSTI]

An electrical system architecture is disclosed. The architecture has a power source configured to generate a first power, and a first bus configured to receive the first power from the power source. The architecture also has a converter configured to receive the first power from the first bus and convert the first power to a second power, wherein a voltage of the second power is greater than a voltage of the first power, and a second bus configured to receive the second power from the converter. The architecture further has a power storage device configured to receive the second power from the second bus and deliver the second power to the second bus, a propulsion motor configured to receive the second power from the second bus, and an accessory motor configured to receive the second power from the second bus.

Hoff, Brian Douglas (East Peoria, IL); Akasam, Sivaprasad (Peoria, IL)

2011-03-22T23:59:59.000Z

323

High voltage photo switch package module  

DOE Patents [OSTI]

A photo-conductive switch package module having a photo-conductive substrate or wafer with opposing electrode-interface surfaces, and at least one light-input surface. First metallic layers are formed on the electrode-interface surfaces, and one or more optical waveguides having input and output ends are bonded to the substrate so that the output end of each waveguide is bonded to a corresponding one of the light-input surfaces of the photo-conductive substrate. This forms a waveguide-substrate interface for coupling light into the photo-conductive wafer. A dielectric material such as epoxy is then used to encapsulate the photo-conductive substrate and optical waveguide so that only the metallic layers and the input end of the optical waveguide are exposed. Second metallic layers are then formed on the first metallic layers so that the waveguide-substrate interface is positioned under the second metallic layers.

Sullivan, James S; Sanders, David M; Hawkins, Steven A; Sampayan, Stephen E

2014-02-18T23:59:59.000Z

324

High-voltage-compatible, fully depleted CCDs  

E-Print Network [OSTI]

B. Flaugher, “The dark energy survey,” Inter. J. of ModernTelescope (LSST), 1 the Dark Energy Survey camera, 2 the

2006-01-01T23:59:59.000Z

325

Polymerizable Additive for Passivating High Voltage Cathodes  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

batteries with the goal of significantly increasing battery energy density. Conventional Li-ion battery electrolyte systems are quite unstable at these high potentials, leading to...

326

Verification of an IGBT Fusing Switch for Over-current Protection of the SNS HVCM  

SciTech Connect (OSTI)

An IGBT based over-current protection system has been developed to detect faults and limit the damage caused by faults in high voltage converter modulators. During normal operation, an IGBT enables energy to be transferred from storage capacitors to a H-bridge. When a fault occurs, the over-current protection system detects the fault, limits the fault current and opens the IGBT to isolate the remaining stored energy from the fault. This paper presents an experimental verification of the over-current protection system under applicable conditions.

Benwell, Andrew; Kemp, Mark; Burkhart, Craig; Nguyen, Minh; /SLAC; ,

2010-06-11T23:59:59.000Z

327

Changing Direct Current to Alternating Current by Means of Thyratrons  

Science Journals Connector (OSTI)

...Laboratory, General Electric Company. | Journal Article...LABORATORY, GENERAL ELECTRIC COMPANY Read before the...alternating for transmission of electric power has many well recognized...method of controlling an arc discharge by means of a grid...

Albert W. Hull

1936-01-01T23:59:59.000Z

328

Geothermal Energy: Current abstracts  

SciTech Connect (OSTI)

This bulletin announces the current worldwide information available on the technologies required for economic recovery of geothermal energy and its use as direct heat or for electric power production. (ACR)

Ringe, A.C. (ed.)

1988-02-01T23:59:59.000Z

329

Superconducting Fault Current Limiter for Transmission Voltage  

Science Journals Connector (OSTI)

Within a collaboration of American Superconductor, Siemens, Nexans and Southern California Edison one electrical phase of a resistive superconducting fault current limiter for the 115 kV transmission voltage level has been designed and manufactured. The active part of the limiter consists of 63 bifilar coils made of 12 mm wide steel-stabilized YBCO conductor and is housed in a cryostat operated at 5 bar and 74 K. The first phase was completely assembled and successfully subjected to power switching tests and high voltage tests. The basic design of the system and the test results are reported. The work was funded in part by US-DOE under Contract Number DE-FC26-07NT43243.

Hans-Peter Kraemer; Wolfgang Schmidt; Hong Cai; Bruce Gamble; David Madura; Tim MacDonald; Joe McNamara; Walther Romanosky; Greg Snitchler; Nicolas Lallouet; Frank Schmidt; Syed Ahmed

2012-01-01T23:59:59.000Z

330

Anomalous - viscosity current drive  

DOE Patents [OSTI]

An apparatus and method for maintaining a steady-state current in a toroidal magnetically confined plasma. An electric current is generated in an edge region at or near the outermost good magnetic surface of the toroidal plasma. The edge current is generated in a direction parallel to the flow of current in the main plasma and such that its current density is greater than the average density of the main plasma current. The current flow in the edge region is maintained in a direction parallel to the main current for a period of one or two of its characteristic decay times. Current from the edge region will penetrate radially into the plasma and augment the main plasma current through the mechanism of anomalous viscosity. In another aspect of the invention, current flow driven between a cathode and an anode is used to establish a start-up plasma current. The plasma-current channel is magnetically detached from the electrodes, leaving a plasma magnetically insulated from contact with any material obstructions including the cathode and anode.

Stix, Thomas H. (Princeton, NJ); Ono, Masayuki (Princeton Junction, NJ)

1988-01-01T23:59:59.000Z

331

Pacific Direct Current Intertie (PDCI) Upgrade Project  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Accommodate increased power transmission - The upgrade will allow even more clean power, including hydro, wind and solar, to reach markets that need it. Upgrading and...

332

Optical crystal based devices for current and voltage measurement  

SciTech Connect (OSTI)

A prerequisite for safe, stable operation of an electric power system is accurate, reliable measurement of the system parameters, in particular, current and voltage. Traditionally this has been achieved on High Voltage (HV) systems by expensive, bulky iron-cored current transformers (CTs) and capacitor voltage transformers (VTs). Both these devices are increasingly coming under review in modern power systems due to their cost, safety implications for personnel and surrounding plant if failure occurs, installation time and indeed substation land requirements. This paper describes novel designs for magneto-optic and electro-optic crystal sensors providing potentially separate and combined current and voltage measurement. The results of testing programs are presented and details of the work associated with field trials given.

Cruden, A.; Richardson, Z.J.; McDonald, J.R.; Andonovic, I. [Univ. of Strathclyde (United Kingdom)] [Univ. of Strathclyde (United Kingdom)

1995-07-01T23:59:59.000Z

333

Method for sputtering with low frequency alternating current  

DOE Patents [OSTI]

Low frequency alternating current sputtering is provided by connecting a low frequency alternating current source to a high voltage transformer having outer taps and a center tap for stepping up the voltage of the alternating current. The center tap of the transformer is connected to a vacuum vessel containing argon or helium gas. Target electrodes, in close proximity to each other, and containing material with which the substrates will be coated, are connected to the outer taps of the transformer. With an applied potential, the gas will ionize and sputtering from the target electrodes onto the substrate will then result. The target electrodes can be copper or boron, and the substrate can be stainless steel, aluminum, or titanium. Copper coatings produced are used in place of nickel and/or copper striking. 6 figs.

Timberlake, J.R.

1996-04-30T23:59:59.000Z

334

Method for sputtering with low frequency alternating current  

DOE Patents [OSTI]

Low frequency alternating current sputtering is provided by connecting a low frequency alternating current source to a high voltage transformer having outer taps and a center tap for stepping up the voltage of the alternating current. The center tap of the transformer is connected to a vacuum vessel containing argon or helium gas. Target electrodes, in close proximity to each other, and containing material with which the substrates will be coated, are connected to the outer taps of the transformer. With an applied potential, the gas will ionize and sputtering from the target electrodes onto the substrate will then result. The target electrodes can be copper or boron, and the substrate can be stainless steel, aluminum, or titanium. Copper coatings produced are used in place of nickel and/or copper striking.

Timberlake, John R. (Allentown, NJ)

1996-01-01T23:59:59.000Z

335

Nonlinear Control Design and Analysis of a Multi-Terminal VSC-HVDC System  

E-Print Network [OSTI]

Nonlinear Control Design and Analysis of a Multi-Terminal VSC-HVDC System Yijing Chen1, Jing Dai1-terminal voltage- source converter based high-voltage direct current (multi- terminal VSC-HVDC) system-Source Converter based High-Voltage Direct Current (VSC-HVDC) multipoint networks could be a good solution

Paris-Sud XI, Université de

336

Chapter 17. High-Voltage Systems and Dielectric Materials High-Voltage Systems and Dielectric Materials  

E-Print Network [OSTI]

aromatic, naphthenic, and paraffinic molecules with complex molecular structures. With the advancement

337

Surface Wind Direction Variability  

Science Journals Connector (OSTI)

Common large shifts of wind direction in the weak-wind nocturnal boundary layer are poorly understood and are not adequately captured by numerical models and statistical parameterizations. The current study examines 15 datasets representing a ...

Larry Mahrt

2011-01-01T23:59:59.000Z

338

Determination of High-Frequency Current Distribution Using EMTP-Based Transmission Line Models with Resulting Radiated Electromagnetic Fields  

SciTech Connect (OSTI)

Application of BPL technologies to existing overhead high-voltage power lines would benefit greatly from improved simulation tools capable of predicting performance - such as the electromagnetic fields radiated from such lines. Existing EMTP-based frequency-dependent line models are attractive since their parameters are derived from physical design dimensions which are easily obtained. However, to calculate the radiated electromagnetic fields, detailed current distributions need to be determined. This paper presents a method of using EMTP line models to determine the current distribution on the lines, as well as a technique for using these current distributions to determine the radiated electromagnetic fields.

Mork, B; Nelson, R; Kirkendall, B; Stenvig, N

2009-11-30T23:59:59.000Z

339

Leakage currents in 4H-SiC JBS diodes  

SciTech Connect (OSTI)

Leakage currents in high-voltage 4H-SiC diodes, which have an integrated (p-n) Schottky structure (Junction Barrier Schottky, JBS), have been studied using commercial diodes and specially fabricated (based on a commercial epitaxial material) test Schottky diodes with and without the JBS structure. It is shown that (i) the main role in reverse charge transport is played by SiC crystal structure defects, most probably, by threading dislocations (density {approx}10{sup 4} cm{sup -2}), and (ii) the JBS structure, formed by the implantation of boron, partially suppresses the leakage currents (by up to a factor of 10 at optimal separation, 8 {mu}m between local p-type regions).

Ivanov, P. A., E-mail: Pavel.Ivanov@mail.ioffe.ru; Grekhov, I. V.; Potapov, A. S.; Kon'kov, O. I.; Il'inskaya, N. D.; Samsonova, T. P. [Russian Academy of Sciences, Ioffe Physical Technical Institute (Russian Federation); Korol'kov, O.; Sleptsuk, N. [Tallinn University of Technology, Department of Electronics (Estonia)

2012-03-15T23:59:59.000Z

340

Departmental Directives Program  

Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

To define requirements and responsibilities for implementing the Department of Energy (DOE) Directives Program in support of the Secretary's memorandum of September 10, 2007, Principles Governing Departmental Directives. See also the current list of Directives Requiring Further Documentation, as required by Appendix D of this Order. Cancels DOE P 251.1A, DOE O 251.1B, DOE M 251.1-1B.

2007-09-10T23:59:59.000Z

Note: This page contains sample records for the topic "high-voltage direct current" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Quench current degradation in superconducting coil for 6.6 kV/2 fault current limiter  

SciTech Connect (OSTI)

A 6.6 kV/2 kA class fault current limiter that consists of non-inductive superconducting windings was developed and tested. The limiter can deliver continuous power at 2 kArms and limit fault current of more than 20 kA to 4 kA in 6 kV. The limiter recovers to the superconducting state within a few seconds and can perform a fault current limiting operation in 60 seconds after the last limiting operation. After high-voltage operation, however, the quench current of the limiter dropped significantly. This quench current degradation is related to the coil bobbin strain due to helium pressure raised by large ohmic heating in quenching. The degradation is a fatal problem for a fault current limiter if the quench current falls below the operating current because the limiter cannot revert to the normal operation. High Young`s modulus bobbin is effective to remove the coil degradation. They have obtained a fault current limiter without any degradation after repeated limiting operations.

Tasaki, K.; Yazawa, T.; Yoneda, E.S.; Nomura, S.; Maeda, H. [Toshiba Corp., Kawasaki (Japan). Research and Development Center] [Toshiba Corp., Kawasaki (Japan). Research and Development Center; Ohkuma, T.; Nakade, M.; Hara, T. [Tokyo Electric Power Co., Yokohama (Japan). Power Engineering R and D Center] [Tokyo Electric Power Co., Yokohama (Japan). Power Engineering R and D Center

1996-07-01T23:59:59.000Z

342

Beam current sensor  

DOE Patents [OSTI]

A current sensor for measuring the dc component of a beam of charged particles employs a superconducting pick-up loop probe, with twisted superconducting leads in combination with a Superconducting Quantum Interference Device (SQUID) detector. The pick-up probe is in the form of a single-turn loop, or a cylindrical toroid, through which the beam is directed and within which a first magnetic flux is excluded by the Meisner effect. The SQUID detector acts as a flux-to-voltage converter in providing a current to the pick-up loop so as to establish a second magnetic flux within the electrode which nulls out the first magnetic flux. A feedback voltage within the SQUID detector represents the beam current of the particles which transit the pick-up loop. Meisner effect currents prevent changes in the magnetic field within the toroidal pick-up loop and produce a current signal independent of the beam's cross-section and its position within the toroid, while the combination of superconducting elements provides current measurement sensitivities in the nano-ampere range.

Kuchnir, M.; Mills, F.E.

1984-09-28T23:59:59.000Z

343

Beam current sensor  

DOE Patents [OSTI]

A current sensor for measuring the DC component of a beam of charged particles employs a superconducting pick-up loop probe, with twisted superconducting leads in combination with a Superconducting Quantum Interference Device (SQUID) detector. The pick-up probe is in the form of a single-turn loop, or a cylindrical toroid, through which the beam is directed and within which a first magnetic flux is excluded by the Meisner effect. The SQUID detector acts as a flux-to-voltage converter in providing a current to the pick-up loop so as to establish a second magnetic flux within the electrode which nulls out the first magnetic flux. A feedback voltage within the SQUID detector represents the beam current of the particles which transit the pick-up loop. Meisner effect currents prevent changes in the magnetic field within the toroidal pick-up loop and produce a current signal independent of the beam's cross-section and its position within the toroid, while the combination of superconducting elements provides current measurement sensitivites in the nano-ampere range.

Kuchnir, Moyses (Elmhurst, IL); Mills, Frederick E. (Elburn, IL)

1987-01-01T23:59:59.000Z

344

Definition: Alternating current | Open Energy Information  

Open Energy Info (EERE)

Alternating current Alternating current Jump to: navigation, search Dictionary.png Alternating current An electric current that reverses its direction at regularly recurring intervals. In the United States, the standard is 120 reversals or 60 cycles per second. Electricity transmission networks use AC.[1][2] View on Wikipedia Wikipedia Definition In alternating current (AC, also ac), the flow of electric charge periodically reverses direction. In direct current (DC, also dc), the flow of electric charge is only in one direction. The abbreviations AC and DC are often used to mean simply alternating and direct, as when they modify current or voltage. AC is the form in which electric power is delivered to businesses and residences. The usual waveform of an AC power circuit is a

345

Energy Currents  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

7 7 Energy Currents Survey Result Our thanks to all of you who responded to our reader survey. We were pleased that many of you find this a useful publication. Your opinions will help us improve it further. The CBS News' readers include a variety of professions. 17% of respondents were consultants, 15% were engineers, 11% were teachers, 11% were scientists, 10% were program managers. The remainder included contractors, designers, marketing professionals policy analysts, journalists and others. Ranked according to highest response first, the majority of readers work in education, various levels of government, utilities, non-profit organizations, and a variety of private concerns. A surprisingly large number, 52% of the respondents, are Internet users and 23% have browsed the World Wide Web. 8% have browsed the Center's Web site

346

Energy Currents  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

1 1 Energy Currents LBL Scientist Joins Clinton Administration Art Rosenfeld Art Rosenfeld, former head of LBL's Center for Building Science, has been named a senior advisor in the U.S. Department of Energy, serving under Assistant Secretary for Energy Efficiency and Renewable Energy Christine Ervin. His appointment began July 1. In Washington, Rosenfeld will sit on President Clinton's National Science and Technology Council. He will also serve as national spokesperson for the Administration's "Cool Communities" program and will help steer through the political process a proposed new "government-sponsored enterprise"- called EFFIE MAE for Energy Efficiency Mortgage and Loan Agency-that would guarantee loans for retrofitting energy-inefficient public buildings.

347

High-efficiency solar cells fabricated from direct-current magnetron sputtered n-indium tin oxide onto p-InP grown by atmospheric pressure metalorganic vapor phase epitaxy  

SciTech Connect (OSTI)

Solar cells based on dc magnetron sputtered indium tin oxide onto epitaxially grown films of p-InP have been fabricated and analyzed. The best cells had a global efficiency of 18.4% and an air mass zero (AMO) efficiency of 16.0%. The principal fabrication variable considered was the constituency of the sputtering gas and both argon/hydrogen and argon/oxygen mixtures have been used. The former cells have the higher efficiencies, are apparently stable, and exhibit almost ideal junction characteristics. The latter cells are relatively unstable and exhibit much higher ideality factors and reverse saturation current densities. The temperature dependence of the reverse saturation current indicates totally different charge transfer mechanisms in the two cases.

Li, X.; Wanlass, M.W.; Gessert, T.A.; Emery, K.A.; Coutts, T.J.

1989-05-01T23:59:59.000Z

348

Directives Help  

Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

All DOE directives are available through this site. While it may seem overwhelming, given the number of documents, we have provided a number of ways in which you may get to the information you need.

349

Superconducting fault current limiter with fast vacuum commutation modulus  

Science Journals Connector (OSTI)

A new approach to a problem of creation of a resistive version of superconducting fault current limiters (FCL) on the basis of HTS materials has been considered. According to this approach, a scheme of FCL is added by a commutation modulus which contains a fast vacuum interrupter. This interrupter allows one to switch off the transport current as soon as 5 ms after transition of the HTS element to the normal state. The proposed scheme allows one to restrict more than an order in value a necessary operation time of FCL in a regime of a current limitation. As a result, a time of recovering the superconducting state can be significantly reduced that allows FCL to operate in automatic iterative regime. The considering device can operate not only in high voltage ac transmission lines but also in dc electrical networks. A numerical simulation of transit processes in a proposed scheme of FCL has been performed for different regimes and its features are analyzed with respect to other schemes of FCL. An experimental study of test mock-up commutation elements of FCL has been performed. This study demonstrates an efficiency of the proposed scheme. A test of a FCL model with the limiting current up to 15 kA has been realized.

D Alferov; D Yevsin; L Fisher; V Ivanov; V Sidorov

2008-01-01T23:59:59.000Z

350

Design of Electron Cyclotron Heating and Current Drive System of ITER  

SciTech Connect (OSTI)

Since the end of EDA, the design of the Electron Cyclotron Heating and Current Drive (ECH and CD) system has been modified to respond to progress in physics understanding and change of interface conditions. Nominal RF power of 20 MW is shared by four upper launchers or one equatorial launcher RF beams are steered by front steering mirrors providing wide sweeping angle for the RF beam. DC high voltage power supply may be composed of IGBT pulse step modulators because of high frequency modulation and design flexibility to three different types of 170 GHz gyrotrons provided by three parties. The RF power from the 170 GHz gyrotron is transmitted to the launcher by 63.5 mm{phi} corrugated waveguide line and remotely switched by a waveguide switch between the upper launcher and the equatorial launcher. The ECH and CD system has also a start-up sub-system for assist of initial discharge composed of three 127.5 GHz gyrotrons and a dedicated DC high voltage power supply. Three of transmission lines are shared between 170 GHz gyrotron and 127.5 GHz gyrotron so as to inject RF beam for the start-up through the equatorial launcher. R and Ds of components for high power long pulse and mirror steering mechanism have been on-going in the parties to establish a reliable ITER ECH and CD system.

Kobayashi, N. [ITER, Cadarache (France); Bigelow, T.; Rasmussen, D. [ORNL, Oak Ridge (United States); Bonicelli, T.; Ramponi, G.; Saibene, G. [EFDA, Garching (Germany); Cirant, S. [ENEA-CNR, Milan (Italy); Denisov, G. [IAP, Nizhny Novgorod (Russian Federation); Heidinger, R.; Piosczyk, B. [FZK, Karlsruhe (Germany); Henderson, M.; Hogge, J.-P.; Thumm, M.; Tran, M. Q. [CRPP, Lausanne (Switzerland); Rao, S. L. [IPR, Bhat (India); Sakamoto, K.; Takahashi, K. [JAEA, Naka (Japan); Temkin, R. J. [MIT PSFC, Cambridge (United States); Verhoeven, A. G. A. [FOM IPP, Rijnhuizen (Netherlands); Zohm, H. [MPI IPP, Garching (Germany)

2007-09-28T23:59:59.000Z

351

Current balancing for battery strings  

DOE Patents [OSTI]

A battery plant is described which features magnetic circuit means for balancing the electrical current flow through a pluraliircuitbattery strings which are connected electrically in parallel. The magnetic circuit means is associated with the battery strings such that the conductors carrying the electrical current flow through each of the battery strings pass through the magnetic circuit means in directions which cause the electromagnetic fields of at least one predetermined pair of the conductors to oppose each other. In an alternative embodiment, a low voltage converter is associated with each of the battery strings for balancing the electrical current flow through the battery strings.

Galloway, James H. (New Baltimore, MI)

1985-01-01T23:59:59.000Z

352

NETL F 451.1/1-1, Categorical Exclusion Designation Form  

Broader source: Energy.gov (indexed) [DOE]

DE-AC26-07NT42677 RPSEA FE University of Connecticut SCNGO FY14-16 30 months Richard Baker Storrs, CT Subsea High Voltage Direct Current Connectors for Environmentally Safe and...

353

California's electricity system of the future scenario analysis in support of public-interest transmission system R&D planning  

E-Print Network [OSTI]

Voltage Direct Current (HVDC) 10. Underground Cables 11.E2I FACTS FERC GIL GMC GPS HVDC IEEE IOU ISO LADWP MD02 MJare minimal. High-voltage DC (HVDC) lines are not considered

Eto, Joseph; Stovall, John P.

2003-01-01T23:59:59.000Z

354

High Voltage DC Transmission 1.0 Introduction  

E-Print Network [OSTI]

HVDC HelWin 2 Germany - Büttel 53°5501N9° 1355E Germany - HelWin Beta platform 54°2711N 7 °4420E 130 320 690 2015 IGBT HVDC DolWin 2 Germany - Heede 52°5852N7° 1526E Germany - DolWin Bets platform 53 14 450 650 2014 Thy HVDC SylWin 1 Germany - Büttel 53°5501N9° 1355E Germany - SylWin Alpha platform

McCalley, James D.

355

,"Table 6. Proposed High-voltage Transmission Line Additions...  

U.S. Energy Information Administration (EIA) Indexed Site

,2010,"US","WECC","NORW","AC","300-399","300-399",1398,6,2011,"South Jordan, UT","SLC,UT",0,"OH",,,14354,"PACE","I",100,"Camp Williams- Terminal 345 kV 1...

356

,"Table 6. Proposed High-voltage Transmission Line Additions...  

U.S. Energy Information Administration (EIA) Indexed Site

"Planned","Reliability"," " ,"US","SERC","Southeastern","AC","100-120",115,290,5,2014,"Jordan dam","Bouldin Dam",0,"OH","Unknown","Unknown",795,"Other","Single",1,1,195,"Alabama...

357

Electrolytes and Separators for High Voltage Li Ion Cells  

Broader source: Energy.gov [DOE]

2012 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting

358

Nanoscale Morphological and Chemical Changes of High Voltage...  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

reconstructed from nano-tomography data (left panel). The distribution of the three transition metal ions is rendered and quantified in the middle and right columns. In this...

359

Studies on High Voltage Lithium Rich MNC Composite Cathodes  

Broader source: Energy.gov [DOE]

2012 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting

360

Optically-initiated silicon carbide high voltage switch  

DOE Patents [OSTI]

An improved photoconductive switch having a SIC or other wide band gap substrate material, such as GaAs and field-grading liners composed of preferably SiN formed on the substrate adjacent the electrode perimeters or adjacent the substrate perimeters for grading the electric fields.

Caporaso, George J. (Livermore, CA); Sampayan, Stephen E. (Manteca, CA); Sullivan, James S. (Livermore, CA); Sanders, David M. (Livermore, CA)

2012-02-28T23:59:59.000Z

Note: This page contains sample records for the topic "high-voltage direct current" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Highline Pacific Northwests High-Voltage Transmission System  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Elliot Mainzer Greg Delwiche Claudia Andrews Mark Gendron Cathy Ehli Administrators of BPA Nancy Mitman Mission Vision Values History Vintage Film Vault 75th Anniversary...

362

Electrolytes and Separators for High Voltage Li Ion Cells  

Broader source: Energy.gov [DOE]

2011 DOE Hydrogen and Fuel Cells Program, and Vehicle Technologies Program Annual Merit Review and Peer Evaluation

363

Electrolytes and Separators for High Voltage Li Ion Cells  

Broader source: Energy.gov [DOE]

2013 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting

364

High-Voltage Solid Polymer Batteries for Electric Drive Vehicles  

Broader source: Energy.gov [DOE]

2012 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting

365

High-Voltage Solid Polymer Batteries for Electric Drive Vehicles  

Broader source: Energy.gov [DOE]

2013 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting

366

Four generations of high-voltage electron microscopes  

Science Journals Connector (OSTI)

......TM' py and Analysis, ed. Nixon , , , , , ,, , , , W C, p. 188, (Institute of Physics Conf. Series Nr. 10, London ceed only if the ballistic exchange rate exceeds the thermal a n d Bristol). rate sufficiently. This implies that the transformation......

Alfred Seeger

1999-01-01T23:59:59.000Z

367

Studies on High Voltage Lithium Rich MNC Composite Cathodes  

Broader source: Energy.gov (indexed) [DOE]

Compositions from Toda Inc. Subtask 1.2 : Improving the rate performance using 1.5 wt% carbon fiber additives ProgressStatus : 100% complete Task 2: Ex situ SoC analysis of...

368

High Temperature, High Voltage Fully Integrated Gate Driver Circuit  

Broader source: Energy.gov (indexed) [DOE]

driver circuit, 5-V on- chip voltage regulator, short-circuit protection, undervoltage lockout, bootstrap capacitor, dead time controller and temperature sensor * 0.8-micron,...

369

High Voltage Electrolytes for Li-ion Batteries  

Broader source: Energy.gov (indexed) [DOE]

effective than HFiP in improving cycle life in LNMOgraphite cells at RT. - Synthesized Al(HFiP) additives with electron deficient center Al - Calculated oxidation potential of...

370

High Temperature, High Voltage Fully Integrated Gate Driver Circuit  

Broader source: Energy.gov [DOE]

2010 DOE Vehicle Technologies and Hydrogen Programs Annual Merit Review and Peer Evaluation Meeting, June 7-11, 2010 -- Washington D.C.

371

High Temperature, High Voltage Fully Integrated Gate Driver Circuit  

Broader source: Energy.gov [DOE]

2009 DOE Hydrogen Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting, May 18-22, 2009 -- Washington D.C.

372

Automotive high-voltage electrical system with integrated safeguard  

Science Journals Connector (OSTI)

For several years the use of higher system voltages has been a topic in the automotive industry. Whether for hybrid or conventional vehicles, safeguards are required which protect both the vehicle...

Thomas Flottmann

2007-03-01T23:59:59.000Z

373

High Voltage Electrolytes for Li-ion Batteries  

Broader source: Energy.gov [DOE]

2013 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting

374

High-Voltage Solid Polymer Batteries for Electric Drive Vehicles  

Broader source: Energy.gov (indexed) [DOE]

complete Timeline Budget Barriers Partners Overview * Barriers addressed: - A. Battery cost - C. Performance: Energy Density - E. Lifetime * Targets - prototype cells...

375

ESS 2012 Peer Review - Low Cost, Manufacturable High Voltage...  

Broader source: Energy.gov (indexed) [DOE]

11 kV 600 kW ESS 6 Comparison of solutions for a 13.8 kV 480 V 100 kVA substation transformer 2 S. Bhattacharya, "15kV SiC IGBT Modules for Grid Scale Power Conversion",...

376

High Voltage Electrolytes for Li-ion Batteries  

Broader source: Energy.gov (indexed) [DOE]

below 4.5 V; * Sulfone-based solvents showed anodic stability up to 5.8 V but: * SEI chemistry from reduction of sulfones does not provide protection of graphitic anodes * Most...

377

Four generations of high-voltage electron microscopes  

Science Journals Connector (OSTI)

......microscopes 307 Table 3 Edge lengths of elementary cubes. a0, and separations...data were obtained by electrical resistance measurements [41,42], those...measure- ment of the residual electric resistance using 'conven- tional' accelerator......

Alfred Seeger

1999-01-01T23:59:59.000Z

378

CLNS 03/1827 VERY HIGH VOLTAGE PHOTOEMISSION ELECTRON GUNS*  

E-Print Network [OSTI]

photoemission electron guns, will be reviewed. INTRODUCTION The successful demonstration of beam energy recovery with demanding specifications on transverse and longitudinal emittances. DC electron guns with photoemission, there are few restrictions on vacuum chamber geometry or the location and size of ports, and many choices

379

High Voltage Electrolytes for Li-ion Batteries  

Broader source: Energy.gov (indexed) [DOE]

FY09 and FY10 * 400K (DOE) Timeline Budget Barriers * Argonne National Laboratory * Saft Batteries * University of Maryland Partners * State-of-the-art LiPF 6 Carbonate...

380

High Voltage Electrolytes for Li-ion Batteries  

Broader source: Energy.gov (indexed) [DOE]

* Funding for FY12 * 250K Timeline Budget Barriers * Argonne National Laboratory * Saft Batteries * U of Texas, Austin * U of Utah * U of Maryland Partners * SOA electrolytes...

Note: This page contains sample records for the topic "high-voltage direct current" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Direct costing  

E-Print Network [OSTI]

oau 5e reduced. Under the same oonOitions, even ~Me on a bread scale entails not mere1y the conduct of the direct oyeraticns cf yrccessing the materials into finished products, but also the performance of auxiliary functions. these may 'ba power y... purposes have been advanced as folkway le Most of a o03RyaxO' 8 products Grc usual13r sold at prices which oovex' full product costs y plus 861ling a%el administrative expenses, plus normal profit. The inventoi~ valuate. on should be consistent...

Browning, Donald Bullock

2012-06-07T23:59:59.000Z

382

Current drivers and future directions of global livestock disease dynamics  

Science Journals Connector (OSTI)

...demand models other than...and HPAI outbreaks or threats...ability to predict changes is...Endemic disease outbreaks Greater private...and other models Livestock Revolution...2005 ) Models of foot-and-mouth...Web data predict flu . Nature...

Brian D. Perry; Delia Grace; Keith Sones

2013-01-01T23:59:59.000Z

383

Direct Biological Conversion of Electrical Current into Methane by  

E-Print Network [OSTI]

assisted method of hydrogen production (electrohydrogenesis) is that a precious metal catalyst the search for new and sustainable approaches for energy production. Two new methods of bioenergy productionfrombiomassincludeelectricityproductionusing microbial fuel cells (MFCs) and hydrogen production by electrohydrogenesis using microbial

384

http://cdp.sagepub.com/ Current Directions in Psychological  

E-Print Network [OSTI]

A Window on Reality : Perceiving Edited Moving Images Published by: http the cognitive and perceptual bases of film has been a lonely activity. Near the inception of film, some astute to understand film. Part of the reason for this lack of interest has been the presumption that the discontinuous

385

Brushless Separately Excited Direct Current Motor Electric Motors: A Survey  

E-Print Network [OSTI]

Abstract: In this paper the importance of brushless SEDC electric motors in the automotive industry continues to grow, writes Matthew Beecham. The driving force behind market growth is motorists ’ insatiable demand for safety, comfort, economy, a clean environment and overall quality of driving.

R. C. Chourasia; Dr. A. K. Bhardwaj

386

Direct-Current Resistivity Survey At Mt Princeton Hot Springs...  

Open Energy Info (EERE)

Survey Activity Date 2010 Usefulness useful DOE-funding Unknown Notes Used to map fracture and fluid flow patterns. References K. Richards, A. Revil, A. Jardani, F. Henderson,...

387

Direct-Current Resistivity Survey At Long Valley Caldera Geothermal...  

Open Energy Info (EERE)

conductive regions here may be caused by hydrothermal alteration or a fluid filled fracture system." References Daniel F. C. Pribnow, Claudia Schutze, Suzanne J. Hurter,...

388

Current hepatitis B treatment guidelines and future research directions  

Science Journals Connector (OSTI)

Hepatitis B virus (HBV) infection causes a tremendous clinical burden across the world with more than half a million people dying annually from HBV related disease. Significant advances have been made in HBV t...

Jonathan Skupsky; Ke-Qin Hu

2014-06-01T23:59:59.000Z

389

Theoretical Investigation of Bacteria Polarizability under Direct Current Electric Fields  

Science Journals Connector (OSTI)

The characteristic thickness of the electric double layer known as the Debye length is given by ?D* = ((?m*kBT*)/(2z2e2cbulk*))1/2, where kB is the Boltzmann constant, T* is the absolute temperature, cbulk* is the bulk electrolyte concentration, z is the valence of ions in a symmetric z/z electrolyte, and e is the elementary electric charge. ... The fluid experiences a resistance due to the soft layer, which can be modeled within the framework of the Debye–Bueche model. ...

Naga Neehar Dingari; Cullen R. Buie

2014-03-25T23:59:59.000Z

390

Sandia National Laboratories: temporal variation of current direction  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Doppler Velocimeter EC Top Publications A Comparison of Platform Options for Deep-water Floating Offshore Vertical Axis Wind Turbines: An Initial Study Nonlinear Time-Domain...

391

Direct search for dark matter  

SciTech Connect (OSTI)

Dark matter is hypothetical matter which does not interact with electromagnetic radiation. The existence of dark matter is only inferred from gravitational effects of astrophysical observations to explain the missing mass component of the Universe. Weakly Interacting Massive Particles are currently the most popular candidate to explain the missing mass component. I review the current status of experimental searches of dark matter through direct detection using terrestrial detectors.

Yoo, Jonghee; /Fermilab

2009-12-01T23:59:59.000Z

392

IonCCD™ for direct position-sensitive charged-particle detection: from electrons and keV ions to hyperthermal biomolecular ions  

SciTech Connect (OSTI)

A novel charged-particle sensitive, pixel based detector array is described and its usage is demonstrated for a variety of applications, from detection of elemental particles (electrons) to hyper-thermal large biomolecular positive and negative ions including keV light atomic and molecular ions. The array detector is a modified light-sensitive charged coupled device (CCD). The IonCCDTM was engineered for direct charged particle detection by replacing the semi-conductor part of the CCD pixel by a conductor1. In contrast with the CCD, where the semi-conductive pixel is responsible for electron-hole pair formation upon photon bombardment, the IonCCD uses a capacitor coupled to the conductive electrode for direct charge integration. The detector can be operated from atmospheric pressure to high vacuum since no high voltages are needed. The IonCCD, presented in this work is an array of 2126 active pixels with 21 um pixel width and 3 um pixel gap. The detection area is 1.5x51mm2 where 1.5 mm and 51 mm are pixel and detector array length, respectively. The result is a one-dimensional position-sensitive detector with 24 um spatial resolution and 88 % pixel area ratio (PAR). In this work we demonstrate the capabilities and the performance of the detector. For the first time we show the direct detection of 250 eV electrons providing linearity response and detection efficiency of the IonCCD as function of electron beam current. Using positive ions from and electron impact source (E-I), we demonstrate that the detection efficiency of the IonCCD is virtually independent of particle energy [250 eV, 1250 eV], particle impact angle [45o, 90o] and particle flux. By combining the IonCCD with a double focusing sector field of Mattauch-Herzog geometry (M-H), we demonstrate fast acquisition of mass spectra in direct air sniffing mode. A first step towards fast in vivo breath analysis is presented. Detection of hyper-thermal biomolecular ions produced using an electrospray ionization source (ESI) is presented. The IonCCD was used as beam profiler to characterize the beam shape and intensity of 15 eV protonated and deprotonated biomolecular ions at the exit of an RF only collisional quadrupole. We present simultaneous detection of 140 eV doubly protonated biomolecular ions when the IonCCD is combined with the M-H analyzer. The latter, demonstrates the possibility of simultaneous separation and micro-array deposition of biological material using a miniature sector field.

Hadjar, Omar; Johnson, Grant E.; Laskin, Julia; Kibelka, Gottfried; Shill, Scott M.; Kuhn, Ken; Cameron, Chad; Kassan, Scott

2011-04-01T23:59:59.000Z

393

High frequency fast wave current drive for DEMO  

SciTech Connect (OSTI)

A steady-state tokamak reactor (SSTR) requires a high efficiency current drive system, from plug to driven mega-amps. RF systems working in the ion-cyclotron range of frequencies (ICRF) have high efficiency from plug to antenna but a limited current drive (CD) efficiency and centrally peaked CD profiles. The latter feature is not adequate for a SSTR where the current should be sufficiently broad to keep the central safety factor (possibly significantly) above 1. In addition, the fact that the fast wave (FW) is evanescent at the edge limits coupling, requiring high voltage operation, which makes the system dependent on plasma edge properties and prone to arcing, reducing its reliability. A possible way to overcome these weaknesses is to operate at higher frequency (10 times or more the cyclotron frequency). The advantages are: (1) The coupling can be much better (waves propagate in vacuum) if the parallel refractive index n{sub ||} is kept below one, (2) The FW group velocity tends to align to the magnetic field, so the power circumnavigates the magnetic axis and can drive off-axis current, (3) Due to the latter property, n{sub ||} can be upshifted along the wave propagation path, allowing low n{sub ||} launch (hence good coupling, large CD efficiency) with ultimately good electron absorption (which requires higher n{sub ||}. Note however that the n{sub ||} upshift is a self-organized feature, that electron absorption is in competition with {alpha}-particle absorption and that uncoupling of the FW from the lower hybrid resonance at the edge requires n{sub ||} slightly above one. The latter possibly counterproductive features might complicate the picture. The different aspects of this potentially attractive off-axis FWCD scheme are discussed.

Koch, R.; Lerche, E.; Van Eester, D. [LPP/ERM-KMS, Association 'EURATOM-Belgian State', 1000 Brussels, TEC Partner (Belgium); Nightingale, M. [Culham Centre for Fusion Energy, Abingdon OX14 3DB (United Kingdom)

2011-12-23T23:59:59.000Z

394

High Charge State Ions Extracted from Metal Plasmas in the Transition Regime from Vacuum Spark to High Current Vacuum Arc  

SciTech Connect (OSTI)

Metal ions were extracted from pulsed discharge plasmas operating in the transition region between vacuum spark (transient high voltage of kV) and vacuum arc (arc voltage ~;; 20 V). At a peak current of about 4 kA, and with a pulse duration of 8 ?s, we observed mean ion charges states of about 6 for several cathode materials. In the case of platinum, the highest average charge state was 6.74 with ions of charge states as high as 10 present. For gold we found traces of charge state 11, with the highest average charge state of 7.25. At currents higher than 5 kA, non-metallic contaminations started to dominate the ion beam, preventing further enhancement of the metal charge states.

Yushkov, Georgy Yu.; Anders, A.

2008-06-19T23:59:59.000Z

395

An Introduction to Wave-Current Interactions  

E-Print Network [OSTI]

-scale wave focusing across a storm can re-direct the wind-stress? #12;1. Adiabatic interaction StartAn Introduction to Wave-Current Interactions Jerry Smith, MPL-SIO-UCSD jasmith@ucsd.edu http just want to hold up your hand. #12;Some Questions in Wave-Current Interaction Physics 1. Adiabatic

Smith, Jerome A.

396

Current Solicitations - Hanford Site  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Home Prime Contracts Current Solicitations Small Business Other Sources DOE RL Contracting Officers DOE RL Contracting Officer Representatives Current Solicitations Email...

397

Current to Current Corporation | Open Energy Information  

Open Energy Info (EERE)

to Current Corporation to Current Corporation Jump to: navigation, search Name Current to Current Corporation Place Burlington, Massachusetts Zip 1803 Sector Ocean Product Developing a technology which generates power from ocean currents : Submersible Power Generators (SPG). Coordinates 44.446275°, -108.431704° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":44.446275,"lon":-108.431704,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

398

Utility-Scale Power Router: Dynamic Control of Grid Assets Using Direct AC Converter Cells  

SciTech Connect (OSTI)

ADEPT Project: Georgia Tech is developing a cost-effective, utility-scale power router that uses an enhanced transformer to more efficiently direct power on the grid. Existing power routing technologies are too expensive for widespread use, but the ability to route grid power to match real-time demand and power outages would significantly reduce energy costs for utilities, municipalities, and consumers. Georgia Tech is adding a power converter to an existing grid transformer to better control power flows at about 1/10th the cost of existing power routing solutions. Transformers convert the high-voltage electricity that is transmitted through the grid into the low-voltage electricity that is used by homes and businesses. The added converter uses fewer steps to convert some types of power and eliminates unnecessary power storage, among other improvements. The enhanced transformer is more efficient, and it would still work even if the converter fails, ensuring grid reliability.

None

2010-09-01T23:59:59.000Z

399

Direct coupling of pulsed radio frequency and pulsed high power in novel pulsed power system for plasma immersion ion implantation  

SciTech Connect (OSTI)

A novel power supply system that directly couples pulsed high voltage (HV) pulses and pulsed 13.56 MHz radio frequency (rf) has been developed for plasma processes. In this system, the sample holder is connected to both the rf generator and HV modulator. The coupling circuit in the hybrid system is composed of individual matching units, low pass filters, and voltage clamping units. This ensures the safe operation of the rf system even when the HV is on. The PSPICE software is utilized to optimize the design of circuits. The system can be operated in two modes. The pulsed rf discharge may serve as either the seed plasma source for glow discharge or high-density plasma source for plasma immersion ion implantation (PIII). The pulsed high-voltage glow discharge is induced when a rf pulse with a short duration or a larger time interval between the rf and HV pulses is used. Conventional PIII can also be achieved. Experiments conducted on the new system confirm steady and safe operation.

Gong Chunzhi; Tian Xiubo; Yang Shiqin [State Key Laboratory of Advanced Welding Production and Technology, School of Materials Science and Engineering, Harbin Institute of Technology, 150001 Harbin (China); Fu, Ricky K. Y.; Chu, Paul K. [Department of Physics and Materials Science, City University of Hong Kong, Tat Chee Avenue, Kowloon (Hong Kong)

2008-04-15T23:59:59.000Z

400

Current Injection Spiral-Shaped Chaotic Microcavity Quantum Cascade Lasers  

Science Journals Connector (OSTI)

We report room temperature operation of current-injection quantum cascade lasers with spiral-shaped chaotic microresonators, capable of directional, single mode emission, operating...

Belkin, Mikhail A; Audet, Ross M; Fan, Jonathan A; Capasso, Federico; Narimanov, Evgenii; Bour, D; Corzine, S; Zhu, J; Höfler, G

Note: This page contains sample records for the topic "high-voltage direct current" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

LANSCE beam current limiter  

SciTech Connect (OSTI)

The Radiation Security System (RSS) at the Los Alamos Neutron Science Center (LANSCE) provides personnel protection from prompt radiation due to accelerated beam. Active instrumentation, such as the Beam Current Limiter, is a component of the RSS. The current limiter is designed to limit the average current in a beam line below a specific level, thus minimizing the maximum current available for a beam spill accident. The beam current limiter is a self-contained, electrically isolated toroidal beam transformer which continuously monitors beam current. It is designed as fail-safe instrumentation. The design philosophy, hardware design, operation, and limitations of the device are described.

Gallegos, F.R.

1996-06-01T23:59:59.000Z

402

CANDU safety-status and direction  

SciTech Connect (OSTI)

This paper reviews the status and direction of Canada deuterium uranium (CANDU) safety design for the current CANDU product line, with emphasis on the single-unit containment plants.

Snell, V.G.; Allen, P.J. (Atomic Energy of Canada Limited, Sheridan Park (Canada))

1993-01-01T23:59:59.000Z

403

High-Current Accelerators  

E-Print Network [OSTI]

F i g . 13 F i g . 14 A 48 ACCELERATOR F i g . 25 F i g . 16supply. Extrapolation of accelerator energy and current9 . A-48 high-current accelerator, low-velocity end. Fig.

Lawrence, Ernest O.

1955-01-01T23:59:59.000Z

404

Directional detection of dark matter streams  

Science Journals Connector (OSTI)

Directional detection of weakly interacting massive particles, in which the energies and directions of the recoiling nuclei are measured, currently presents the only prospect for probing the local velocity distribution of Galactic dark matter. We investigate the extent to which future directional detectors would be capable of probing dark matter substructure in the form of streams. We analyze the signal expected from a Sagittarius-like stream and also explore the full parameter space of stream speed, direction, dispersion and density. Using a combination of nonparametric directional statistics, a profile likelihood ratio test and Bayesian parameter inference we find that within acceptable exposure times [O(10)??kg?yr for cross sections just below the current exclusion limits] future directional detectors will be sensitive to a wide range of stream velocities and densities. We also examine and discuss the importance of the energy window of the detector.

Ciaran A.?J. O’Hare and Anne M. Green

2014-12-08T23:59:59.000Z

406

Revised: 10-2012 NAME: Michael G. Giesselmann  

E-Print Network [OSTI]

, Ignitrons, Utility Power Systems, Gas Discharges, High Voltage and High Current Design, High Speed Optical

Zhuang, Yu

407

Current Testbed Research  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Current Testbed Research Previous Testbed Research Proposal Process Terms and Conditions Dark Fiber Testbed Performance (perfSONAR) Software & Tools Development Partnerships...

408

Current Research Portfolio  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Resources News & Events Expand News & Events Skip navigation links Smart Grid Demand Response Energy Efficiency Emerging Technologies Current Research Portfolio Behavior Based...

409

Ion current interface.  

E-Print Network [OSTI]

?? Abstract Abstract The reason to measure the ion current in a combustion engine is to extract combustion parameters in order to achieve closed loop… (more)

Johansson, Morgan

2005-01-01T23:59:59.000Z

410

RF current sensor  

DOE Patents [OSTI]

An RF sensor having a novel current sensing probe and a voltage sensing probe to measure voltage and current. The current sensor is disposed in a transmission line to link all of the flux generated by the flowing current in order to obtain an accurate measurement. The voltage sensor is a flat plate which operates as a capacitive plate to sense voltage on a center conductor of the transmission line, in which the measured voltage is obtained across a resistance leg of a R-C differentiator circuit formed by the characteristic impedance of a connecting transmission line and a capacitance of the plate, which is positioned proximal to the center conductor.

Moore, James A. (Powell, TN); Sparks, Dennis O. (Maryville, TN)

1998-11-10T23:59:59.000Z

411

Directives Quarterly Updates  

Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

Listings of new Justification Memoranda and new or revised Directives that have been posted to the DOE Directives, Delegations, and Requirements Portal. Updated quarterly.

412

Another face of DIRECT  

E-Print Network [OSTI]

authors, see for example, tree-Direct [5]. This paper ..... [4] J.M. Gablonsky, Modifications of the DIRECT Algorithm, Ph.D. Thesis, North Carolina State. University ...

chiter

2007-08-01T23:59:59.000Z

413

Highly sensitive vacuum ion pump current measurement system  

DOE Patents [OSTI]

A vacuum system comprising: 1) an ion pump; 2) power supply; 3) a high voltage DC--DC converter drawing power from the power supply and powering the vacuum pump; 4) a feedback network comprising an ammeter circuit including an operational amplifier and a series of relay controlled scaling resistors of different resistance for detecting circuit feedback; 5) an optional power block section intermediate the power supply and the high voltage DC--DC converter; and 6) a microprocessor receiving feedback information from the feedback network, controlling which of the scaling resistors should be in the circuit and manipulating data from the feedback network to provide accurate vacuum measurement to an operator.

Hansknecht, John Christopher (Williamsburg, VA)

2006-02-21T23:59:59.000Z

414

Ultracapacitor current collector  

DOE Patents [OSTI]

An ultracapacitor having two solid, nonporous current collectors, two porous electrodes separating the collectors, a porous separator between the electrodes and an electrolyte occupying the pores in the electrodes and separator. At least one of the current collectors comprises a conductive metal substrate coated with a metal nitride, carbide or boride coating.

Jerabek, Elihu Calfin (Glenmont, NY); Mikkor, Mati (Ann Arbor, MI)

2001-10-16T23:59:59.000Z

415

Tokamak halo currents  

SciTech Connect (OSTI)

A halo current flows for part of its path through the plasma edge and for part through the chamber walls and can be as large as tenths of the plasma current. The primary interest in halo currents is the large force that they can exert on machine components. Two discordant constraints are central to the theory: (1) Halo currents must produce the magnetic field distribution required to maintain plasma force balance—a distribution that depends on the two angular coordinates of a torus. (2) Halo currents must flow along the magnetic field lines in the plasma, which implies a dependence on a linear combination of the two angular coordinates—only one angular coordinate is free. The physics basis of these two constraints is explained as is their application to the calculation of the properties of halo currents, such as their broad toroidal spectrum. Existing codes could be used to (1) provide detailed comparisons with experiments to validate that the critical elements of physics are adequately included, (2) allow more complete predictions for future machines such as ITER, and (3) design shunts and resistive elements to ensure halo currents follow paths that are the least damaging to the machine. The physics of halo currents implies that it may be possible to feedback stabilize resistive wall modes beyond the ideal-wall limit.

Boozer, Allen H. [Department of Applied Physics and Applied Mathematics Columbia University, New York, New York 10027 (United States)] [Department of Applied Physics and Applied Mathematics Columbia University, New York, New York 10027 (United States)

2013-08-15T23:59:59.000Z

416

Fuzzy Estimation of DC Motor Winding Currents Innovatia Software  

E-Print Network [OSTI]

stator windings. an attractive alternative to current estimation using In order to implement an eFuzzy Estimation of DC Motor Winding Currents Dan Simon Innovatia Software 775 Rothrock Circle °ux is rotated in the desired direction of ofuzzy ¯ltering to motor winding current estimation

Simon, Dan

417

Voltage controlled current source  

DOE Patents [OSTI]

A seven decade, voltage controlled current source is described for use in testing intermediate range nuclear instruments that covers the entire test current range of from 10 picoamperes to 100 microamperes. High accuracy is obtained throughout the entire seven decades of output current with circuitry that includes a coordinated switching scheme responsive to the input signal from a hybrid computer to control the input voltage to an antilog amplifier, and to selectively connect a resistance to the antilog amplifier output to provide a continuous output current source as a function of a preset range of input voltage. An operator controlled switch provides current adjustment for operation in either a real-time simulation test mode or a time response test mode.

Casne, Gregory M. (Pittsburgh, PA)

1992-01-01T23:59:59.000Z

418

Methods of Conditioning Direct Methanol Fuel Cells  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Methods of Conditioning Direct Methanol Fuel Cells Methods of Conditioning Direct Methanol Fuel Cells Methods of Conditioning Direct Methanol Fuel Cells Methods for conditioning the membrane electrode assembly of a direct methanol fuel cell ("DMFC") are disclosed. Available for thumbnail of Feynman Center (505) 665-9090 Email Methods of Conditioning Direct Methanol Fuel Cells Methods for conditioning the membrane electrode assembly of a direct methanol fuel cell ("DMFC") are disclosed. In a first method, an electrical current of polarity opposite to that used in a functioning direct methanol fuel cell is passed through the anode surface of the membrane electrode assembly. In a second method, methanol is supplied to an anode surface of the membrane electrode assembly, allowed to cross over the polymer

419

Foreign Direct Investment  

Gasoline and Diesel Fuel Update (EIA)

Investment Investment Foreign Direct Investment Foreign Direct Investment Foreign Direct Investment in U.S. Energy in U.S. Energy in U.S. Energy in U.S. Energy in 1999 in 1999 in 1999 in 1999 June 2001 ii iii Contents Foreign Affiliates' Role in U.S. Energy Industry Operations ..............................................................................1 Foreign Direct Investment: The International Transactions Accounts ..............................................................8 U.S. Companies' Direct Investment Abroad in Energy ......................................................................................14 Conclusion...............................................................................................................................................................19

420

Current Journals Athena Computers  

E-Print Network [OSTI]

Computers Reference Collection Restrooms-outside of library Scanner, Copier, Public Printer Special REFERENCE STUDY SPACE PUBLIC COMPUTERS CURRENT JOURNALS SCANNER, COPIER, PUBLIC PRINTER, ATHENA COMPUTER & Technology Stations Media Room Music Software Stations New Books and Scores Oversize Collection Public

Note: This page contains sample records for the topic "high-voltage direct current" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Accelerated Currents in Superconductors  

Science Journals Connector (OSTI)

It is shown that the ratio of the accelerated currents of energy and matter induced in a superconductor by a long-wavelength electric field is equal to the chemical potential of the system.

Vinay Ambegaokar and Gerald Rickayzen

1966-02-04T23:59:59.000Z

422

Current Physics Information  

Science Journals Connector (OSTI)

...MARKS, R.H., MAY CONV NAT MICR AS ( 1971 ). ROBERTS, L.G., AFIPS C P 36 : 543 ( 1970 ). ZIMAN, J.M., INFORMATION, COMMUNICATION, KNOWLEDGE, NATURE 224 : 318 ( 1969 ). Current physics information. | A new concept in science...

H. William Koch

1971-11-26T23:59:59.000Z

423

Direct/Indirect Costs  

Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

This chapter provides recommended categories for direct and indirect elements developed by the Committee for Cost Methods Development (CCMD) and describes various estimating techniques for direct and indirect costs.

1997-03-28T23:59:59.000Z

424

Directives System Manual  

Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

This Manual provides detailed requirements to supplement DOE O 251.1A, Directives System, dated 1-30-98.

1998-01-30T23:59:59.000Z

425

A study of the Antilles Current using moored current meter arrays  

E-Print Network [OSTI]

characteristics of the Savcnius rotor have been reported previously by Gaul (1962). The output from the current meter is a ro11 of 16 mm photographic film containing current direction and speed data, data on case inclination, and timing pulses. An example... the summer npeia ions, wind directions and speeds were typical for this subtropical latitude being gener;illy out of the east at Table 2. Mooring nositioning data. oorlpg; I I IFix No. !:Date, " Time I !I, " L'ST :I ~L*'- 0. ! I ILongitude Il...

Maloney, William Everett

2012-06-07T23:59:59.000Z

426

Fault Current Limiters  

Broader source: Energy.gov (indexed) [DOE]

Fault Fault Current Limiters Superconducting & Solid-state Power Equipment Office of Electricity Delivery and Energy Reliability www.oe.energy.gov Office of Electricity Delivery and Energy Reliability, OE-1 U.S. Department of Energy - 1000 Independence Avenue, SW - Washington, DC 20585 Plugging America Into the Future of Power What are FCLs? A fault is an unintentional short circuit, or partial short-circuit, in an electric circuit. A variety of factors such as lightning, downed power lines, or crossed power lines cause faults. During a fault, excessive current-called fault current- flows through the electrical system often resulting in a failure of one section of that system by causing a

427

Current Testbed Research  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Research Research R&D Overview 100G Testbed Testbed Description Testbed Results Current Testbed Research Previous Testbed Research Proposal Process Terms and Conditions Virtual Circuits (OSCARS) Performance (perfSONAR) Tools Development Green Networking Authentication & Trust Federation (ATF) Partnerships Contact Us Technical Assistance: 1 800-33-ESnet (Inside the US) 1 800-333-7638 (Inside the US) 1 510-486-7600 (Globally) 1 510-486-7607 (Globally) Report Network Problems: trouble@es.net Provide Web Site Feedback: info@es.net Current Testbed Research The following projects are currently using the ESnet Testbed. Previous testbed projects descriptions are located here. New Projects, Summer 2013 Project Name/PI End-system affinities and the performance of high-speed flows, Dipak Ghosal (UC Davis)

428

Counter Current Multiplier Mechanism  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Counter Current Multiplier Mechanism Counter Current Multiplier Mechanism Name: Stephen Location: N/A Country: N/A Date: N/A Question: Can you please explain to me the counter-current multiplier mechanism. I understand that cholride and sodium ions are filtered out of the ascending loop of Henle into the interstial fluid, however, I'm not sure exactly what happens from there and how this effects osmotic pressure gradients in the nephron. Any help would be greatly appriciated. Replies: This mechanism is very complex when it comes to writing a response. You have to have a strong background in osmotic pressure understanding and the anatomy of the kidney. It involves the cortex, outer and inner medula in relationship to the vasa recta, interstitial fluids at two points, the loop of Henle and the collecting duct. The size of the tubes and the position in relations to the cortex and medulla is an essential part. I can suggest some references.

429

Transformer current sensor for superconducting magnetic coils  

DOE Patents [OSTI]

A transformer current sensor having primary turns carrying a primary current for a superconducting coil and secondary turns only partially arranged within the primary turns. The secondary turns include an active winding disposed within the primary turns and a dummy winding which is not disposed in the primary turns and so does not experience a magnetic field due to a flow of current in the primary turns. The active and dummy windings are wound in opposite directions or connected in series-bucking relationship, and are exposed to the same ambient magnetic field. Voltages which might otherwise develop in the active and dummy windings due to ambient magnetic fields thus cancel out. The resultant voltage is purely indicative of the rate of change of current flowing in the primary turns.

Shen, Stewart S. (Oak Ridge, TN); Wilson, C. Thomas (Norris, TN)

1988-01-01T23:59:59.000Z

430

Hydrogen Delivery- Current Technology  

Broader source: Energy.gov [DOE]

Hydrogen is transported from the point of production to the point of use via pipeline, over the road in cryogenic liquid trucks or gaseous tube trailers, or by rail or barge. Read on to learn more about current hydrogen delivery and storage technologies.

431

Current address: Samuel Johnson  

E-Print Network [OSTI]

CV: E-mail : Homepage: Current address: Samuel Johnson samuel.johnson@imperial.ac.uk www. #12;Submitted work 1. The meaning of niche: Cause or consequence of food-web structure?, S. Johnson, V learning, S. Johnson, J. Marro, and J.J. Torres, PLoS ONE 8(1): e50276 (2013) 3. Enhancing neural network

Johnson, Samuel

432

Clean Cities: Current Financial Opportunities  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Financial Opportunities Financial Opportunities Printable Version Share this resource Send a link to Clean Cities: Current Financial Opportunities to someone by E-mail Share Clean Cities: Current Financial Opportunities on Facebook Tweet about Clean Cities: Current Financial Opportunities on Twitter Bookmark Clean Cities: Current Financial Opportunities on Google Bookmark Clean Cities: Current Financial Opportunities on Delicious Rank Clean Cities: Current Financial Opportunities on Digg Find More places to share Clean Cities: Current Financial Opportunities on AddThis.com... Current Opportunities Related Opportunities Funded Projects Current Financial Opportunities Current transportation-related financial opportunities, including Clean Cities funding opportunity announcements (FOAs) issued by the U.S.

433

FCT Hydrogen Production: Current Technology  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Current Technology to Current Technology to someone by E-mail Share FCT Hydrogen Production: Current Technology on Facebook Tweet about FCT Hydrogen Production: Current Technology on Twitter Bookmark FCT Hydrogen Production: Current Technology on Google Bookmark FCT Hydrogen Production: Current Technology on Delicious Rank FCT Hydrogen Production: Current Technology on Digg Find More places to share FCT Hydrogen Production: Current Technology on AddThis.com... Home Basics Current Technology Thermal Processes Electrolytic Processes Photolytic Processes R&D Activities Quick Links Hydrogen Delivery Hydrogen Storage Fuel Cells Technology Validation Manufacturing Codes & Standards Education Systems Analysis Contacts Current Technology The development of clean, sustainable, and cost-competitive hydrogen

434

Current Status of Concentrator Photovoltaic (CPV) Technology  

SciTech Connect (OSTI)

This report describes the current status of the market and technology for concentrator photovoltaic (CPV) cells and modules. Significant progress in CPV has been achieved, including record efficiencies for modules (36.7%) and cells (46%), as well as growth of large field installations in recent years. CPV technology may also have the potential to be cost-competitive on a levelized cost of energy (LCOE) basis in regions of high direct normal irradiance (DNI). The study includes an overview of all installations larger than 1 MW, information on companies currently active in the CPV field, efficiency data, and estimates of the LCOE in different scenarios.

Philipps, S. P.; Bett, A. W.; Horowitz, K.; Kurtz, S.

2015-01-01T23:59:59.000Z

435

Joule heating generated by spin current through Josephson junctions  

SciTech Connect (OSTI)

We theoretically study the spin-polarized current flowing through a Josephson junction (JJ) in a spin injection device. When the spin-polarized current is injected from a ferromagnet in a superconductor (SC), the charge current is carried by the superconducting condensate (Cooper pairs), while the spin-up and spin-down currents flow in equal magnitude but in the opposite direction in a SC, because of no quasiparticle charge current in the SC. This indicates that not only the Josephson current but also the spin current flow across JJ at zero bias voltage, thereby generating Joule heating by the spin current. The result provides a new method for detecting the spin current by measuring Joule heating at JJ. {copyright} 2001 American Institute of Physics.

Takahashi, S.; Yamashita, T.; Koyama, T.; Maekawa, S.; Imamura, H.

2001-06-01T23:59:59.000Z

436

CMVRTC: Current Research  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Current reseach projects Current reseach projects Wireless Roadside Inspection Field Operational Test (WRI-FOT) Brake Defect Causation and Abatement Study Infrared-Based Screening System Overweight Vehicle Defect Study WRI-fot WRI-FOT roadmap In Fall of 2012, FMCSA kicked offed the WRI-FOT Program to validate technologies and methodologies that can improve safety through inspections using wireless technologies that convey real-time identification of commercial motor vehicles (CMV), drivers, and carriers, as well as information about the status of the vehicles and their drivers. It is believed that these inspections will (1) increase CMV safety, (2) increase inspection efficiency, (3) improve inspection effectiveness by reducing the probability of drivers bypassing CMV inspection stations and

437

Contracting Polymer with Current  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Contracting Polymer with Current Contracting Polymer with Current Name: Ian Status: student Grade: 9-12 Location: PA Country: USA Date: Summer 2011 Question: Hello and thank you in advance. I have previously read of a material ( a kind of "rubber") that contracts when an electric current is applied. My question is what is this material, how does it work/what is it made of? Thank you very much. Replies: Hi Ian, I believe the material you are referring to is a kind of piezoelectric rubber. Piezoelectric materials (usually they are special types of ceramics or crystals) produce an electrical voltage when compressed of otherwise subjected to stress. They also do the opposite... they slightly expand or contract when a voltage is applied. But the amount they expand or contract is very small indeed. For example, one square meter of the recently discovered piezoelectric rubber materials typically contracts a mere 100 picometers for ever applied volt. Translated into everyday measurements, this means that if you apply a voltage of 1 Volt to a one foot long piece of this rubber, it will only contract less than half a billionth of an inch! Applying 100 volts will cause it to contract just under 50 billionths of an inch!

438

Directives System Manual  

Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

This Manual provides detailed requirements to supplement DOE O 251.1, which establishes requirements for the development, coordination, and sunset review of DOE directives.

1995-10-16T23:59:59.000Z

439

Departmental Directives Program  

Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

To establish directives as the primary means to set, communicate, and institutionalize policies, requirements, responsibilities, and procedures for Departmental elements and contractors.

2014-10-16T23:59:59.000Z

440

Quantum pumping of valley current in strain engineered graphene  

SciTech Connect (OSTI)

We studied the generation of valley dependent current by adiabatic quantum pumping in monolayer graphene in the presence of electric potential barriers, ferromagnetic field and strain. The pumped currents in the two valleys have same magnitudes and opposite directions; thus, a pure valley current is generated. The oscillation of the pumped pure valley current is determined by the Fabry-Perot resonances formed in the structure. In our calculation, the pumped pure valley current can be as high as 50?nA, which is measurable using present technologies. The proposed device is useful for the development of graphene valleytronic devices.

Wang, Jing [Department of Physics, University of Science and Technology of China, Hefei (China) [Department of Physics, University of Science and Technology of China, Hefei (China); Department of Physics and Materials Science and Centre for Functional Photonics, City University of Hong Kong, Hong Kong and City University of Hong Kong Shenzhen Research Institute, Shenzhen (China); Chan, K. S., E-mail: apkschan@cityu.edu.hk, E-mail: zjlin@ustc.edu.cn [Department of Physics and Materials Science and Centre for Functional Photonics, City University of Hong Kong, Hong Kong and City University of Hong Kong Shenzhen Research Institute, Shenzhen (China); Lin, Zijing, E-mail: apkschan@cityu.edu.hk, E-mail: zjlin@ustc.edu.cn [Department of Physics, University of Science and Technology of China, Hefei (China)] [Department of Physics, University of Science and Technology of China, Hefei (China)

2014-01-06T23:59:59.000Z

Note: This page contains sample records for the topic "high-voltage direct current" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Ripping Graphene: Preferred Directions  

Science Journals Connector (OSTI)

Ripping Graphene: Preferred Directions ... Here we present experimental and theoretical studies on cracks or tears in suspended monolayer graphene membranes. ... Edges from mechanically induced ripping exhibit straight lines and are predominantly aligned in the armchair or zigzag directions of the graphene lattice. ...

Kwanpyo Kim; Vasilii I. Artyukhov; William Regan; Yuanyue Liu; M. F. Crommie; Boris I. Yakobson; A. Zettl

2011-12-12T23:59:59.000Z

442

Departmental Directives System  

Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

The order establishes the directives system to be used for publishing permanent and temporary directives issued by DOE Headquarters and addressed to Headquarters and/or field elements. Chg 1 dated 3-14-85. Cancels DOE 1321.1A.

1983-04-07T23:59:59.000Z

443

Currents, Berkeley Lab's Biweekly Newspaper  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Currents Index A-Z Index Search Phone Book Comments Ernest Orlando Lawrence Berkeley National Laboratory Search Currents Back Issues (1994 to present) Search Lab science articles...

444

Current HMS Observations - Hanford Site  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Station Real Time Met Data from Around the Site Current HMS Observations Daily HMS Extremes in Met Data Met and Climate Data Summary Products Contacts Hours Current NWS...

445

direct_deposit_111609  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

PROTECT YOUR BANKING INFORMATION: PROTECT YOUR BANKING INFORMATION: DO NOT complete this form until you are ready to submit it to the Payroll Department. DIRECT DEPOSIT REQUEST Directions: 1. Provide required information neatly, legibly; 2. If Checking Account Direct Deposit, include a voided check. a. DO NOT submit a deposit slip! 3. If Savings Account Direct Deposit, include a copy of savings card. 4. Sign this form; 5. Inter-office mail it to Craft Payroll at "P238." DIRECT DEPOSITION AUTHORIZATION I hereby authorize Los Alamos National Laboratory, hereinafter called The Laboratory, to initiate credit entries and, if necessary, debit entries and adjustments for any credit entries in error to my account listed on this form. If deposit is for:

446

Directions and Maps  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Directions & Maps Directions & Maps Plan Your Visit Visit About the Museum Museum Hours Directions & Maps When to Visit Arrange for a Visit Around Los Alamos Contact Us invisible utility element Directions and Maps Aerial View of Los Alamos Aerial approach to the Los Alamos airport Where we're located Los Alamos (elevation 7,355 feet) is perched high atop the Pajarito Plateau in the Jemez Mountains, 35 miles northwest of Santa Fe. The Bradbury Science Museum is located in downtown Los Alamos at the corner of Central Avenue and 15th Street. If you're driving here and using GPS navigation, our address is 1350 Central Avenue, Los Alamos, NM 87544. How to get here From Albuquerque take I-25 north to Santa Fe (take NM 599 for most direct route), then US 84/285 north to Pojoaque. At Pojoaque take the NM 502 exit

447

Chapter 2 - The History of Measuring Ocean Currents  

Science Journals Connector (OSTI)

Abstract This chapter begins with a brief mention of the contributions made by the ancient mariners in the “discovery” of oceanic currents. Subsequent efforts made by several investigators in this direction, toward development of various devices for measurements of oceanic currents, are then addressed. These include technologies for measurement of surface currents, subsurface and abyssal currents, seafloor boundary layer currents, and vertical profiling of horizontal currents. Surface current measurement technologies include the application of drifting surface bodies; imaging of surface water motion trajectories and patterns with the support of aerial photography, radiometry, and active microwave radar systems; and vector mapping based on current-driven sea-surface wave transport. This is followed by discussion of technologies developed for subsurface and abyssal current measurements. These include spatially integrated measurements based on earth’s magnetism and oceanic sound speed, Lagrangian measurements based on motion of drifting subsurface floats, and Eulerian measurements with the support of a multitude of devices such as suspended drag, propeller revolution registration by mechanical counters, unidirectional impeller current meters, Savonius rotor current meters, ultrasonic acoustic methods, thermal sensors for measurements of turbulent motions, laser Doppler sensors, and acoustic Doppler current meters. This chapter further addresses an important topic of seafloor boundary layer current measurements using mechanical devices and nonmechanical devices such as BASS and MAVS. The chapter concludes with a discussion of technologies developed for vertical profiling of horizontal currents.

Antony Joseph

2014-01-01T23:59:59.000Z

448

Predictions of fast wave heating, current drive, and current drive antenna arrays for advanced tokamaks  

SciTech Connect (OSTI)

The objective of the advanced tokamak program is to optimize plasma performance leading to a compact tokamak reactor through active, steady state control of the current profile using non-inductive current drive and profile control. To achieve these objectives requires compatibility and flexibility in the use of available heating and current drive systems--ion cyclotron radio frequency (ICRF), neutral beams, and lower hybrid. For any advanced tokamak, the following are important challenges to effective use of fast waves in various roles of direct electron heating, minority ion heating, and current drive: (1) to employ the heating and current drive systems to give self-consistent pressure and current profiles leading to the desired advanced tokamak operating modes; (2) to minimize absorption of the fast waves by parasitic resonances, which limit current drive; (3) to optimize and control the spectrum of fast waves launched by the antenna array for the required mix of simultaneous heating and current drive. The authors have addressed these issues using theoretical and computational tools developed at a number of institutions by benchmarking the computations against available experimental data and applying them to the specific case of TPX.

Batchelor, D.B.; Baity, F.W.; Carter, M.D. [and others

1994-12-31T23:59:59.000Z

449

Argonne Transportation Current News  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Current News November 21, 2013 -- Pixelligent Technologies Working with Argonne to Develop Nanoadditives under DOE SBIR Grant November 4, 2013 -- New GREET Model Released October 25, 2013 -- Argonne Creates IdleBox Toolkit for DOE's Clean Cities Initiative to Help Reduce Vehicle Idling September 23, 2013 -- New VISION Model Released for Estimating Potential Energy Use, Oil Use and Carbon Emission Impacts September 17, 2013 -- Water Assessment for Transportation Energy Resources (WATER) Tool Released September 9, 2013 -- Dileep Singh to Receive Prestigious Lee Hsun Award July 17, 2013 -- Summer 2013 TransForum now available July 10, 2013 -- Argonne Wins Four R&D 100 Awards March 23, 2013 -- White House Women's Leadership Summit on Climate and Energy recognizes Argonne scientists

450

Current Concepts: Flavivirus Encephalitis  

Science Journals Connector (OSTI)

..., which has caused encephalitis outbreaks in Brazil, and Murray Valley encephalitis virus in Australia, New Guinea, and New Zealand. Kunjin virus, which also circulates in Australia, recently has been reclassified as a subtype of West Nile virus. In terms of numbers, the most important member of the... West Nile virus is one member of the genus flavivirus, which includes mosquito-borne viruses that cause similar disease patterns in much of the world. The other members of this serogroup include the St. Louis encephalitis virus, the Murray Valley virus, and the Japanese encephalitis virus (which causes thousands of deaths each year in Asia). This review summarizes what is currently known about flavivirus encephalitis, with emphasis on the pathogenesis of West Nile virus infections.

Solomon T.

2004-07-22T23:59:59.000Z

451

Plasma-Current Multipole Experiments  

Science Journals Connector (OSTI)

The magnetohydrodynamic equilibrium and stability of the plasma-current multipole configuration have been demonstrated experimentally.

T. Ohkawa and H. G. Voorhies

1969-06-16T23:59:59.000Z

452

Pumping single-file colloids: Absence of current reversal  

E-Print Network [OSTI]

We consider the single-file motion of colloidal particles interacting via short-ranged repulsion and placed in a traveling wave potential, that varies periodically in time and space. Under suitable driving conditions, a directed time-averaged flow of colloids is generated. We obtain analytic results for the model using a perturbative approach to solve the Fokker-Planck equations. The predictions show good agreement with numerical simulations. We find peaks in the time-averaged directed current as a function of driving frequency, wavelength and particle density and discuss possible experimental realizations. Surprisingly, unlike a closely related exclusion dynamics on a lattice, the directed current in the present model does not show current reversal with density. A linear response formula relating current response to equilibrium correlations is also proposed.

Debasish Chaudhuri; Archishman Raju; Abhishek Dhar

2014-09-24T23:59:59.000Z

453

FCT Hydrogen Delivery: Current Technology  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Current Technology to someone Current Technology to someone by E-mail Share FCT Hydrogen Delivery: Current Technology on Facebook Tweet about FCT Hydrogen Delivery: Current Technology on Twitter Bookmark FCT Hydrogen Delivery: Current Technology on Google Bookmark FCT Hydrogen Delivery: Current Technology on Delicious Rank FCT Hydrogen Delivery: Current Technology on Digg Find More places to share FCT Hydrogen Delivery: Current Technology on AddThis.com... Home Basics Current Technology R&D Activities Quick Links Hydrogen Production Hydrogen Storage Fuel Cells Technology Validation Manufacturing Codes & Standards Education Systems Analysis Contacts Current Technology Today, hydrogen is transported from the point of production to the point of use via pipeline, over the road in cryogenic liquid trucks or gaseous tube

454

FCT Hydrogen Storage: Current Technology  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Current Technology to someone Current Technology to someone by E-mail Share FCT Hydrogen Storage: Current Technology on Facebook Tweet about FCT Hydrogen Storage: Current Technology on Twitter Bookmark FCT Hydrogen Storage: Current Technology on Google Bookmark FCT Hydrogen Storage: Current Technology on Delicious Rank FCT Hydrogen Storage: Current Technology on Digg Find More places to share FCT Hydrogen Storage: Current Technology on AddThis.com... Home Basics Current Technology Gaseous and Liquid Hydrogen Storage Materials-Based Hydrogen Storage Hydrogen Storage Challenges Status of Hydrogen Storage Technologies DOE R&D Activities Quick Links Hydrogen Production Hydrogen Delivery Fuel Cells Technology Validation Manufacturing Codes & Standards Education Systems Analysis Contacts Current Technology

455

Direct Discharge Permit (Vermont)  

Broader source: Energy.gov [DOE]

A direct discharge permit is required if a project involves the discharge of pollutants to state waters. For generation purposes, this involves the withdrawal of surface water for cooling purposes...

456

Directed transport in equilibrium  

E-Print Network [OSTI]

We investigate how a microscopic system, which can move only in one direction, comes to equilibrium with a heat-bath. To understand this problem, we investigate a symmetry broken dimer constrained to move in a particular direction when in contact with a uniform heat-bath at a constant temperature. The dimer is not driven by any external force. The system gains kinetic energy from the heat-bath and that the system can only use in directed transport. At the hard core collision limit between the particles of the dimer, we show by exact analytic calculations and complementary numerical results that the dimer undergoes steady directed transport by attaining a stationary distribution for a relevant degree of freedom. Our observation, being perfectly consistent with the {\\it second law of thermodynamics}, leads to a generalization of the existing {\\it Brownian ratchet} paradigm and points out some important limitations of {\\it Fokker-Planck} dynamics.

Bhattacharyay, A

2010-01-01T23:59:59.000Z

457

Art Directable Tornadoes  

E-Print Network [OSTI]

......................................................................... 25 2. Directional Force ........................................................... 26 3. Vortex Force .................................................................. 26 4. Lattice... ................................................................... 7 7 Tornado in its rope stage before disappearing ........................................... 9 8 Fire vortex and Waterspout ........................................................................ 10 9 Landspout and Gustnado...

Dwivedi, Ravindra

2011-08-08T23:59:59.000Z

458

Refrigerant directly cooled capacitors  

DOE Patents [OSTI]

The invention is a direct contact refrigerant cooling system using a refrigerant floating loop having a refrigerant and refrigeration devices. The cooling system has at least one hermetic container disposed in the refrigerant floating loop. The hermetic container has at least one electronic component selected from the group consisting of capacitors, power electronic switches and gating signal module. The refrigerant is in direct contact with the electronic component.

Hsu, John S. (Oak Ridge, TN); Seiber, Larry E. (Oak Ridge, TN); Marlino, Laura D. (Oak Ridge, TN); Ayers, Curtis W. (Kingston, TN)

2007-09-11T23:59:59.000Z

459

New Directions in Direct Dark Matter Searches  

E-Print Network [OSTI]

I present the status of direct dark matter detection with specific attention to the experimental results and their phenomenological interpretation in terms of dark matter interactions. In particular I review a new and more general approach to study signals in this field based on non-relativistic operators which parametrize more efficiently the dark matter-nucleus interactions in terms of a very limited number of relevant degrees of freedom. Then I list the major experimental results, pointing out the main uncertainties that affect the theoretical interpretation of the data. Finally, since the underlying theory that describes both the dark matter and the standard model fields is unknown, I address the uncertainties coming from the nature of the interaction. In particular, the phenomenology of a class of models in which the interaction between dark matter particles and target nuclei is of a long-range type is discussed.

Paolo Panci

2014-02-06T23:59:59.000Z

460

Advances and new directions in direct liquefaction  

SciTech Connect (OSTI)

With advance in single stage processes such as H-Coal, EDS and SRC, and refining and upgrading of coal liquids by Chevron and UOP, the direct liquefaction process has continuously evolved to the present two-stage catalytic configuration, which produces the highest liquid yield and product quality of any process worldwide. The Two Stage Liquefaction (TSL) process has been successfully applied to bituminous and subbituminous coals, overcoming problems associated with earlier processes. But, potential for additional improvement is recognized in several areas: cleaning coal prior to liquefaction; low temperature and pressure preconditioning of feed coal; novel catalysts development to arrest regressive reactions and improve hydrotreatment and cracking reactions; improvement in hydrocarbon value recovery and reduced energy rejection by alternate bottoms processing techniques. In this paper, after discussing briefly the history of liquefaction and development of the TSL process, present potential areas for research and development are presented.

Rao, S.N.; Schindler, H.D.; McGurl, G.V.

1988-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "high-voltage direct current" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

VOLTAGE COLLAPSE AND TRANSIENT ENERGY FUNCTION ANALYSES OF AC/DC SYSTEMS  

E-Print Network [OSTI]

for power system dynamic models, including a third order representation of high voltage direct current (HVDC power limits, HVDC firing angle limits and voltage dependent current order limits (VDCOL) are shown the derivation of individual component Lyapunov functions for simplified models of HVDC links connected

Cañizares, Claudio A.

462

Oscillatory nonohomic current drive for maintaining a plasma current  

DOE Patents [OSTI]

Apparatus and methods are described for maintaining a plasma current with an oscillatory nonohmic current drive. Each cycle of operation has a generation period in which current driving energy is applied to the plasma, and a relaxation period in which current driving energy is removed. Plasma parameters, such as plasma temperature or plasma average ionic charge state, are modified during the generation period so as to oscillate plasma resistivity in synchronism with the application of current driving energy. The invention improves overall current drive efficiencies.

Fisch, N.J.

1984-01-01T23:59:59.000Z

463

Oscillatory nonhmic current drive for maintaining a plasma current  

DOE Patents [OSTI]

Apparatus and method of the invention maintain a plasma current with an oscillatory nonohmic current drive. Each cycle of operation has a generation period in which current driving energy is applied to the plasma, and a relaxation period in which current driving energy is removed. Plasma parameters, such as plasma temperature or plasma average ionic charge state, are modified during the generation period so as to oscillate plasma resistivity in synchronism with the application of current driving energy. The invention improves overall current drive efficiencies.

Fisch, Nathaniel J. (Princeton, NJ)

1986-01-01T23:59:59.000Z

464

Geothermal direct use engineering and design guidebook  

SciTech Connect (OSTI)

The Geothermal Direct Use Engineering and Design Guidebook is designed to be a comprehensive, thoroughly practical reference guide for engineers and designers of direct heat projects. These projects could include the conversion of geothermal energy into space heating and cooling of buildings, district heating, greenhouse heating, aquaculture and industrial processing. The Guidebook is directed at understanding the nature of geothermal resources and the exploration of the resources, fluid sampling techniques, drilling, and completion of geothermal wells through well testing, and reservoir evaluation. It presents information useful to engineers on the specification of equipment including well pumps, piping, heat exchangers, space heating equipment, heat pumps and absorption refrigeration. A compilation of current information about greenhouse aquaculture and industrial applications is included together with a discussion of engineering cost analysis, regulation requirements, and environmental consideration. The purpose of the Guidebook is to provide an integrated view for the development of direct use projects for which there is a very large potential in the United States.

Lienau, P.J.; Lunis, B.C. (eds.)

1991-01-01T23:59:59.000Z

465

Geothermal direct use engineering and design guidebook  

SciTech Connect (OSTI)

The Geothermal Direct Use Engineering and Design Guidebook is designed to be a comprehensive, thoroughly practical reference guide for engineers and designers of direct heat projects. These projects could include the conversion of geothermal energy into space heating cooling of buildings, district heating, greenhouse heating, aquaculture and industrial processing. The Guidebook is directed at understanding the nature of geothermal resources and the exploration of these resources, fluid sampling techniques, drilling, and completion of geothermal wells through well testing, and reservoir evaluation. It presents information useful to engineers on the specification of equipment including well pumps, piping, heat exchangers, space heating equipment, heat pumps and absorption refrigeration. A compilation of current information about greenhouse, aquaculture and industrial applications is included together with a discussion of engineering cost analysis, regulation requirements, and environmental considerations. The purpose of the Guidebook is to provide an integrated view for the development of direct use projects for which there is a very potential in the United States.

Bloomquist, R.G.; Culver, G.; Ellis, P.F.; Higbee, C.; Kindle, C.; Lienau, P.J.; Lunis, B.C.; Rafferty, K.; Stiger, S.; Wright, P.M.

1989-03-01T23:59:59.000Z

466

Microsoft Word - HVDC Workshop Agenda - Final  

Broader source: Energy.gov (indexed) [DOE]

US Department of Energy's Grid Tech Team US Department of Energy's Grid Tech Team hosts Applications for High-Voltage Direct Current Transmission Technologies April 22, 2013 NRECA Conference Center 4301 Wilson Blvd. Arlington, VA 22203 Objective This workshop is aimed at developing a better understanding of the potential for High Voltage Direct Current (HVdc) transmission technologies and its application in the North American electric grid. Through a series of case studies and group discussions, DOE would like to identify the state-of-the-art for HVdc transmission technologies, including performance and benefits. The workshop will also discuss technical and institutional barriers to greater deployment and possible opportunities to address those barriers. Background The advantages of HVdc transmission over conventional High Voltage Alternating Current

467

Direct memory access transfer completion notification  

DOE Patents [OSTI]

Methods, compute nodes, and computer program products are provided for direct memory access (`DMA`) transfer completion notification. Embodiments include determining, by an origin DMA engine on an origin compute node, whether a data descriptor for an application message to be sent to a target compute node is currently in an injection first-in-first-out (`FIFO`) buffer in dependence upon a sequence number previously associated with the data descriptor, the total number of descriptors currently in the injection FIFO buffer, and the current sequence number for the newest data descriptor stored in the injection FIFO buffer; and notifying a processor core on the origin DMA engine that the message has been sent if the data descriptor for the message is not currently in the injection FIFO buffer.

Chen, Dong (Croton on Hudson, NY); Giampapa, Mark E. (Irvington, NY); Heidelberger, Philip (Cortlandt Manor, NY); Kumar, Sameer (White Plains, NY); Parker, Jeffrey J. (Rochester, MN); Steinmacher-Burow, Burkhard D. (Esslingen, DE); Vranas, Pavlos (Danville, CA)

2010-07-27T23:59:59.000Z

468

Current Annualized Request  

Broader source: Energy.gov (indexed) [DOE]

Organization Organization FY 2012 FY 2013 FY 2014 Current Annualized Request CR $ % National Security Weapons Activities* 7,214,834 7,557,342 7,868,409 +311,067 +4.1% Defense Nuclear Nonproliferation 2,300,950 2,409,930 2,140,142 -160,808 -7.0% Naval Reactors 1,080,000 1,086,610 1,246,134 +166,134 +15.4% Office of the Administrator 410,000 412,509 397,784 -12,216 -3.0% Total, National Nuclear Security Administration 11,005,784 11,466,391 11,652,469 +304,177 +2.8% Energy and Environment Energy Efficiency and Renewable Energy 1,780,548 1,820,713 2,775,700 +995,152 +55.9% Electricity Delivery and Energy Reliability 136,178 139,954 169,015 +32,837 +24.1% Fossil Energy 554,806 714,033 637,975 +83,169 +15.0% Nuclear Energy 853,816 863,996 735,460 -118,356 -13.9% Race to the Top for Energy Efficiency and Grid Modernization

469

MHK Technologies/Current Catcher | Open Energy Information  

Open Energy Info (EERE)

Catcher Catcher < MHK Technologies Jump to: navigation, search << Return to the MHK database homepage Current Catcher.png Technology Profile Primary Organization Offshore Islands Ltd Technology Resource Click here Current Technology Type Click here Axial Flow Turbine Technology Description The Current Catcher harnesses the power and fluctuations of the ocean s currents to generate energy It uses cones to increase the velocity of the ocean current and to direct it to the turbine blades to maximize the production of energy which in turn is transferred through electrical swivels The Current Catcher uses conventional low cost steel tubular frames These frames can support both ocean and tidal current power generators rigidly fixed to the seabed or moored to the seabed

470

Computing plasma focus pinch current from total current measurement  

Science Journals Connector (OSTI)

The total current I total waveform in a plasma focus discharge is the most commonly measured quantity contrasting with the difficult measurement of I pinch . However yield laws should be scaled to focus pinch current I pinch rather than the peak I total . This paper describes how I pinch may be computed from the I total trace by fitting a computed current trace to the measured current trace using the Lee model. The method is applied to an experiment in which both the I total trace and the plasma sheath current trace were measured. The result shows good agreement between the values of computed and measured I pinch .

S. Lee; S. H. Saw; P. C. K. Lee; R. S. Rawat; H. Schmidt

2008-01-01T23:59:59.000Z

471

Heat Transfer and Convection Currents  

Science Journals Connector (OSTI)

...October 1965 research-article Heat Transfer and Convection Currents D. C...convection in a medium with internal heat generation is discussed semi-quantitatively...States English United Kingdom 1966 Heat transfer and convection currents Tozer D...

1965-01-01T23:59:59.000Z

472

Directional gamma detector  

DOE Patents [OSTI]

An improved directional gamma radiation detector has a collector sandwiched etween two layers of insulation of varying thicknesses. The collector and insulation layers are contained within an evacuated casing, or emitter, which releases electrons upon exposure to gamma radiation. Delayed electrons and electrons entering the collector at oblique angles are attenuated as they pass through the insulation layers on route to the collector.

LeVert, Francis E. (Downers Grove, Knoxville, TN); Cox, Samson A. (Downers Grove, IL)

1981-01-01T23:59:59.000Z

473

Extension of DOE Directives  

Broader source: Directives, Delegations, and Requirements [Office of Management (MA)]

This Notice extends the following directives until 2/16/04: DOE N 205.2, Foreign National Access to DOE Cyber Systems, and DOE N 205.3, Password Generation, Protection, and Use, dated 11/23/99-7/1/00.

2003-02-24T23:59:59.000Z

474

Current Experiments in Particle Physics (September 1996)  

SciTech Connect (OSTI)

This report contains summaries of current and recent experiments in Particle Physics. Included are experiments at BEPC (Beijing), BNL, CEBAF, CERN, CESR, DESY, FNAL, Frascati, ITEP (Moscow), JINR (Dubna), KEK, LAMPF, Novosibirsk, PNPI (St. Petersburg), PSI, Saclay, Serpukhov, SLAC, and TRIUMF, and also several proton decay and solar neutrino experiments. Excluded are experiments that finished taking data before 1991. Instructions are given for the World Wide Web (WWW) searching of the computer database (maintained under the SLAC-SPIRES system) that contains the summaries. This report contains full summaries of 180 approved current and recent experiments in elementary particle physics. The focus of the report is on selected experiments which directly contribute to our better understanding of elementary particles and their properties such as masses, widths or lifetimes, and branching fractions.

Galic, H.; Lehar, F.; Klyukhin, V.I.; Ryabov, Yu.G.; Bilak, S.V.; Illarionova, N.S.; Khachaturov, B.A.; Strokovsky, E.A.; Hoffman, C.M.; Kettle, P.-R.; Olin, A.; Armstrong, F.E.

1996-09-01T23:59:59.000Z

475

Current Awards | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

National Laser User Facilities Program Current Awards Current Awards National Laser Users' Facility Grant Program Current Awards Under Construction...

476

Current Awards | National Nuclear Security Administration  

National Nuclear Security Administration (NNSA)

Stewardship Science Academic Alliances Program Current Awards Current Awards Stewardship Science Academic Alliances (SSAA) Program Current Awards Under Construction...

477

Letter: Direction and Guidance for Implementing Direct DOE Relationship &  

Broader source: Energy.gov (indexed) [DOE]

Letter: Direction and Guidance for Implementing Direct DOE Letter: Direction and Guidance for Implementing Direct DOE Relationship & Funding for EMSSABs Letter: Direction and Guidance for Implementing Direct DOE Relationship & Funding for EMSSABs From: Assistant Secretary, Jessie Hill Roberson (EM-11) To: Mr. Monte Wilson, Chair, INEEL Citizens Advisory Board This letter is in response to a November 21, 2003 letter regarding direction and guidance for implementing direct DOE relationship and funding for Environmental Management Site Specific Advisory Boards. Roberson Letter - December 12, 2003 More Documents & Publications Letter: Progress in Implementing a Direct DOE Relationship & Funding for the EMSSABs Letter: Mission, Objectives & Scope of the Site Specific Advisory Board Memorandum: Direction and Guidance for Implementing Direct DOE Relationship

478

Letter: Direction and Guidance for Implementing Direct DOE Relationship &  

Broader source: Energy.gov (indexed) [DOE]

Letter: Direction and Guidance for Implementing Direct DOE Letter: Direction and Guidance for Implementing Direct DOE Relationship & Funding for EMSSABs Letter: Direction and Guidance for Implementing Direct DOE Relationship & Funding for EMSSABs From: Assistant Secretary, Jessie Hill Roberson (EM-11) To: Mr. Monte Wilson, Chair, INEEL Citizens Advisory Board This letter is in response to a November 21, 2003 letter regarding direction and guidance for implementing direct DOE relationship and funding for Environmental Management Site Specific Advisory Boards. Roberson Letter - December 12, 2003 More Documents & Publications Letter: Progress in Implementing a Direct DOE Relationship & Funding for the EMSSABs Letter: Mission, Objectives & Scope of the Site Specific Advisory Board Memorandum: Direction and Guidance for Implementing Direct DOE Relationship

479

Fault current limiter and alternating current circuit breaker  

DOE Patents [OSTI]

A solid-state circuit breaker and current limiter are disclosed for a load served by an alternating current source having a source impedance, the solid-state circuit breaker and current limiter comprising a thyristor bridge interposed between the alternating current source and the load, the thyristor bridge having four thyristor legs and four nodes, with a first node connected to the alternating current source, and a second node connected to the load. A coil is connected from a third node to a fourth node, the coil having an impedance of a value calculated to limit the current flowing therethrough to a predetermined value. Control means are connected to the thyristor legs for limiting the alternating current flow to the load under fault conditions to a predetermined level, and for gating the thyristor bridge under fault conditions to quickly reduce alternating current flowing therethrough to zero and thereafter to maintain the thyristor bridge in an electrically open condition preventing the alternating current from flowing therethrough for a predetermined period of time. 9 figs.

Boenig, H.J.

1998-03-10T23:59:59.000Z

480

Fault current limiter and alternating current circuit breaker  

SciTech Connect (OSTI)

A solid-state circuit breaker and current limiter for a load served by an alternating current source having a source impedance, the solid-state circuit breaker and current limiter comprising a thyristor bridge interposed between the alternating current source and the load, the thyristor bridge having four thyristor legs and four nodes, with a first node connected to the alternating current source, and a second node connected to the load. A coil is connected from a third node to a fourth node, the coil having an impedance of a value calculated to limit the current flowing therethrough to a predetermined value. Control means are connected to the thyristor legs for limiting the alternating current flow to the load under fault conditions to a predetermined level, and for gating the thyristor bridge under fault conditions to quickly reduce alternating current flowing therethrough to zero and thereafter to maintain the thyristor bridge in an electrically open condition preventing the alternating current from flowing therethrough for a predetermined period of time.

Boenig, Heinrich J. (Los Alamos, NM)

1998-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "high-voltage direct current" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Definition: Direct normal irradiance | Open Energy Information  

Open Energy Info (EERE)

normal irradiance normal irradiance (Redirected from Definition:DNI) Jump to: navigation, search Dictionary.png Direct normal irradiance the amount of solar radiation received per unit area by a surface perpendicular (normal) to the rays that come in a straight line from the direction of the sun at its current position in the sky.[1] Also Known As DNI Related Terms Solar radiation, Irradiance, Concentrating solar power, Global horizontal irradiance References ↑ http://www.3tier.com/en/support/glossary/#dni Retrie LikeLike UnlikeLike You like this.Sign Up to see what your friends like. ved from "http://en.openei.org/w/index.php?title=Definition:Direct_normal_irradiance&oldid=423379" Category: Definitions What links here Related changes Special pages Printable version Permanent link

482

MHK Technologies/Current Power | Open Energy Information  

Open Energy Info (EERE)

Power Power < MHK Technologies Jump to: navigation, search << Return to the MHK database homepage Current Power.jpg Technology Profile Primary Organization Current Power AB Project(s) where this technology is utilized *MHK Projects/Norde lv Technology Resource Click here Current/Tidal Technology Type Click here Cross Flow Turbine Technology Readiness Level Click here TRL 1-3: Discovery / Concept Definition / Early Stage Development & Design & Engineering Technology Description The Current Power device is a slow speed vertical axis turbine that utilizes a direct drive permanent magnet rotating generator The concept is based on a vertical axle turbine directly coupled to a permanent magnet synchronous generator The system is intended to be placed on the bottom of the ocean or a river where it would be protected from storm surges and strong waves The output from the generator has to be rectified and inverted before connection to the grid Robustness is achived by the simple mechanical construction

483

Geothermal Energy Technology: a current-awareness bulletin  

SciTech Connect (OSTI)

This bulletin announces on a semimonthly basis the current worldwide information available on the technology required for economic recovery of geothermal energy and its use either directly or for production of electric power. The subject content encompasses: resource status and assessment, geology and hydrology of geothermal systems, geothermal exploration, legal and institutional aspects, economic and final aspects, environmental aspects and waste disposal, by-products, geothermal power plants, geothermal engineering, direct energy utilization, and geothermal data and theory.

Smith, L.B. (ed.)

1983-01-15T23:59:59.000Z

484

Ionization tube simmer current circuit  

DOE Patents [OSTI]

A highly efficient flash lamp simmer current circuit utilizes a fifty percent duty cycle square wave pulse generator to pass a current over a current limiting inductor to a full wave rectifier. The DC output of the rectifier is then passed over a voltage smoothing capacitor through a reverse current blocking diode to a flash lamp tube to sustain ionization in the tube between discharges via a small simmer current. An alternate embodiment of the circuit combines the pulse generator and inductor in the form of an FET off line square wave generator with an impedance limited step up output transformer which is then applied to the full wave rectifier as before to yield a similar simmer current.

Steinkraus, Jr., Robert F. (Livermore, CA)

1994-01-01T23:59:59.000Z

485

Ionization tube simmer current circuit  

DOE Patents [OSTI]

A highly efficient flash lamp simmer current circuit utilizes a fifty percent duty cycle square wave pulse generator to pass a current over a current limiting inductor to a full wave rectifier. The DC output of the rectifier is then passed over a voltage smoothing capacitor through a reverse current blocking diode to a flash lamp tube to sustain ionization in the tube between discharges via a small simmer current. An alternate embodiment of the circuit combines the pulse generator and inductor in the form of an FET off line square wave generator with an impedance limited step up output transformer which is then applied to the full wave rectifier as before to yield a similar simmer current. 6 figures.

Steinkraus, R.F. Jr.

1994-12-13T23:59:59.000Z

486

Particle Detector / Beam Current Transformer  

E-Print Network [OSTI]

Particle Detector / Beam Current Transformer Analysis December 8, 2009 Harold G. Kirk #12;ShotSignal,A.U. Proton Bunch Number Beam Current Transformer - 17011 0 2 4 6 8 0 2 4 6 8 10 12 14 16 18 20 Integrated Transformer Pump 187829 (au) Probe 196504 (au) Ratios: Beam Current 1.046 SF 1.019 2.9% difference #12;Shot

McDonald, Kirk

487

Current Jobs | Argonne National Laboratory  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Job Openings Argonne National Laboratory is currently hiring Co-op students in the following areas: Facilities Management and Services Division: The Facilities Management and...

488

ARM - Lesson Plans: Ocean Currents  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Ocean Currents Outreach Home Room News Publications Traditional Knowledge Kiosks Barrow, Alaska Tropical Western Pacific Site Tours Contacts Students Study Hall About ARM Global...

489

Current Month Summary - Hanford Site  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Station Real Time Met Data from Around the Site Current HMS Observations Daily HMS Extremes in Met Data Met and Climate Data Summary Products Historical Weather Charts Contacts...

490

Breakout Session -- TEC Direction  

Broader source: Energy.gov (indexed) [DOE]

III: TEC III: TEC Direction and Priorities Presented to: Transportation External Coordination Working Group Presented by: Alex Thrower Office of Logistics Management February 7, 2008 San Antonio, Texas 2 Topics of Discussion * Transportation External Coordination Working Group (TEC) charter and membership * Topic group functions * Meeting format 3 TEC Charter and Membership * Mission - TEC was formed in 1992 to improve coordination among the Department of Energy (DOE) and external groups interested in the Department's transportation activities The Office of Civilian Radioactive Waste Management (OCRWM) co-chairs TEC with DOE's Environmental Management Program Provides an opportunity for broad based input and information exchange from varied organizations - Members meet semi-annually to participate in

491

Anomalous-viscosity current drive  

DOE Patents [OSTI]

The present invention relates to a method and apparatus for maintaining a steady-state current for magnetically confining the plasma in a toroidal magnetic confinement device using anomalous viscosity current drive. A second aspect of this invention relates to an apparatus and method for the start-up of a magnetically confined toroidal plasma.

Stix, T.H.; Ono, M.

1986-04-25T23:59:59.000Z

492

Direct Aerosol Forcing Uncertainty  

DOE Data Explorer [Office of Scientific and Technical Information (OSTI)]

Understanding sources of uncertainty in aerosol direct radiative forcing (DRF), the difference in a given radiative flux component with and without aerosol, is essential to quantifying changes in Earth's radiation budget. We examine the uncertainty in DRF due to measurement uncertainty in the quantities on which it depends: aerosol optical depth, single scattering albedo, asymmetry parameter, solar geometry, and surface albedo. Direct radiative forcing at the top of the atmosphere and at the surface as well as sensitivities, the changes in DRF in response to unit changes in individual aerosol or surface properties, are calculated at three locations representing distinct aerosol types and radiative environments. The uncertainty in DRF associated with a given property is computed as the product of the sensitivity and typical measurement uncertainty in the respective aerosol or surface property. Sensitivity and uncertainty values permit estimation of total uncertainty in calculated DRF and identification of properties that most limit accuracy in estimating forcing. Total uncertainties in modeled local diurnally averaged forcing range from 0.2 to 1.3 W m-2 (42 to 20%) depending on location (from tropical to polar sites), solar zenith angle, surface reflectance, aerosol type, and aerosol optical depth. The largest contributor to total uncertainty in DRF is usually single scattering albedo; however decreasing measurement uncertainties for any property would increase accuracy in DRF. Comparison of two radiative transfer models suggests the contribution of modeling error is small compared to the total uncertainty although comparable to uncertainty arising from some individual properties.

Mccomiskey, Allison

493

Radio-Frequency Current Drive in a Fusion-Producing Plasma  

Science Journals Connector (OSTI)

A method for driving current in a fusion-producing plasma is proposed. Radio-frequency power is used to prohibit fusion-produced energetic particles from slowing down isotropically or to push them in a preferential direction. As a result, a net plasma current is generated whose efficiency is comparable to other current drive schemes.

D. K. Bhadra and C. Chu

1982-06-28T23:59:59.000Z

494

Current Drive in Recombining Plasma  

SciTech Connect (OSTI)

The Langevin equations describing the average collisional dynamics of suprathermal particles in nonstationary plasma remarkably admit an exact analytical solution in the case of recombining plasma. The current density produced by arbitrary particle fluxes is derived including the effect of charge recombination. Since recombination has the effect of lowering the charge density of the plasma, thus reducing the charged particle collisional frequencies, the evolution of the current density can be modified substantially compared to plasma with fixed charge density. The current drive efficiency is derived and optimized for discrete and continuous pulses of current, leading to the discovery of a nonzero "residual" current density that persists indefinitely under certain conditions, a feature not present in stationary plasmas.

P.F. Schmit and N.J. Fisch

2012-05-15T23:59:59.000Z

495

Energy current imaging method for time reversal in elastic media  

SciTech Connect (OSTI)

An energy current imaging method is presented for use in locating sources of wave energy during the back propagation stage of the time reversal process. During the back propagation phase of an ideal time reversal experiment, wave energy coalesces from all angles of incidence to recreate the source event; after the recreation, wave energy diverges in every direction. An energy current imaging method based on this convergence/divergence behavior has been developed. The energy current imaging method yields a smaller spatial distribution for source reconstruction than is possible with traditional energy imaging methods.

Anderson, Brian E [Los Alamos National Laboratory; Ulrich, Timothy J [Los Alamos National Laboratory; Le Bas, Pierre - Yves A [Los Alamos National Laboratory; Larmat, Carene [Los Alamos National Laboratory; Johnson, Paul A [Los Alamos National Laboratory; Guyer, Robert A [UNR; Griffa, Michele [ETH ZURICH

2009-01-01T23:59:59.000Z

496

Current  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

E"Bdv, 1 where magnetic helicity, a measure of the knottedness of the magnetic field lines, is defined as KA"Bdv p z , p is the poloidal flux passing...

497

Foreign Direct Investment in U  

Gasoline and Diesel Fuel Update (EIA)

Foreign Direct Investment in U.S. Energy in 1998 Foreign Direct Investment in U.S. Energy in 1998 Foreign Direct Investment Foreign Direct Investment Foreign Direct Investment Foreign Direct Investment in U.S. Energy in U.S. Energy in U.S. Energy in U.S. Energy in 1998 in 1998 in 1998 in 1998 November 2000 Energy Information Administration/Foreign Direct Investment in U.S. Energy in 1998 Contacts This report was prepared in the Office of Energy Markets and End Use of the Energy Information Administration, U.S. Department of Energy, under the general direction of W. Calvin Kilgore. The project was directed by Mark E. Rodekohr, Director of the Energy Markets and Contingency Information Division (202) 586-1441, and Mary E. Northup, the Team Leader for Financial Analysis (202) 586-1383. Specific technical information concerning this

498

SRNL - Directions and Maps  

Broader source: All U.S. Department of Energy (DOE) Office Webpages (Extended Search)

Map of SRS, with Georgia and South Carolina Map of SRS, with Georgia and South Carolina Directions and Maps The Savannah River National Laboratory is located at the Savannah River Site , a 310 square mile site located in the southeastern coastal area of the United States in the state of South Carolina. It is bordered to the west by the Savannah River and Georgia, and is close to several major cities, including Augusta and Savannah (Ga.), Columbia, Greenville, and Charleston (S.C.). It is in an area residents refer to as the Central Savannah River Area, or CSRA. The Aiken County Technology Laboratory (which houses SRNL's biotechnology laboratories and certain waste treatment technology laboratories) and the Center for Hydrogen Research are located at Aiken County's Savannah River Research Campus, located adjacent to SRS.

499

Semiconductor Alternating-Current Motor Drives and Energy Conservation  

Science Journals Connector (OSTI)

...required to avoid high heating losses in the motors...important user concerns-price, efficiency, and...been offered at a price thatjustified broad...direct-ly, causes motor heating, mechanical stress...000 barrels of oil equivalent per day...University, New Haven, Connecticut, and is currently...

D. J. BenDaniel; E. E. David Jr.

1979-11-16T23:59:59.000Z

500

Ring current intensity estimated from low-altitude proton observations  

E-Print Network [OSTI]

. Oksavik Department of Physics, University of Bergen, Bergen, Norway D. S. Evans NOAA Space Environment as a proxy for estimating the energy injection rate into the ring current (RC) due to energetic protons. The injection rate Q(t) is not based upon solar wind parameters but directly on the observed proton

Bergen, Universitetet i